--- linux-xilinx-zynqmp-5.15.0.orig/.github/pull_request_template.md
+++ linux-xilinx-zynqmp-5.15.0/.github/pull_request_template.md
@@ -0,0 +1,3 @@
+Please do not submit a Pull Request via github.  Our project makes use of
+mailing lists for patch submission and review.  For more details please see
+https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842172/Create+and+Submit+a+Patch
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/stable/sysfs-driver-dma-idxd
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/stable/sysfs-driver-dma-idxd
@@ -220,6 +220,24 @@
 Description:	Show the current number of entries in this WQ if WQ Occupancy
 		Support bit WQ capabilities is 1.
 
+What:		/sys/bus/dsa/devices/wq<m>.<n>/op_config
+Date:		Sept 14, 2022
+KernelVersion:	6.0.0
+Contact:	dmaengine@vger.kernel.org
+Description:	Shows the operation capability bits displayed in bitmap format
+		presented by %*pb printk() output format specifier.
+		The attribute can be configured when the WQ is disabled in
+		order to configure the WQ to accept specific bits that
+		correlates to the operations allowed. It's visible only
+		on platforms that support the capability.
+
+What:		/sys/bus/dsa/devices/wq<m>.<n>/enqcmds_retries
+Date		Oct 29, 2021
+KernelVersion:	5.17.0
+Contact:	dmaengine@vger.kernel.org
+Description:	Indicate the number of retires for an enqcmds submission on a shared wq.
+		A max value to set attribute is capped at 64.
+
 What:           /sys/bus/dsa/devices/engine<m>.<n>/group_id
 Date:           Oct 25, 2019
 KernelVersion:  5.6.0
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/stable/sysfs-driver-firmware-zynqmp
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/stable/sysfs-driver-firmware-zynqmp
@@ -113,3 +113,100 @@
 		    # echo 0 > /sys/devices/platform/firmware\:zynqmp-firmware/health_status
 
 Users:		Xilinx
+
+What:		/sys/devices/platform/firmware\:zynqmp-firmware/last_reset_reason
+Date:		Feb 2021
+KernelVersion:	5.10.0
+Contact:	"Tejas Patel" <tejasp@xilinx.com>
+Description:
+		This sysfs interface allows to get last reset reason.
+
+		Usage:
+		Get last reset reason
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/last_reset_reason
+
+Users:		Xilinx
+
+What:		/sys/devices/platform/firmware\:zynqmp-firmware/feature_config_*
+Date:		Jul 2021
+KernelVersion:	TBD
+Contact:	"Ronak Jain" <ronak.jain@xilinx.com>
+Description:
+		This sysfs interface allows to configure features at runtime.
+		The user can enable or disable features running at firmware.
+		Also, the user can configure the parameters of the features
+		at runtime. The supported features are over temperature and
+		external watchdog. Here, the external watchdog is completely
+		different than the /dev/watchdog as the external watchdog is
+		running on the firmware and it is used to monitor the health
+		of firmware not APU(Linux). Also, the external watchdog is
+		interfaced outside of the zynqmp soc.
+
+		By default the features are disabled in the firmware. The user
+		can enable features by querying appropriate config id of the
+		features.
+
+		The default limit for the over temperature is 90 Degree Celsius.
+		The default timer interval for the external watchdog is 570ms.
+
+		The supported config ids are for the feature configuration is,
+		1. PM_FEATURE_OVERTEMP_STATUS = 1, the user can enable or
+		disable the over temperature feature.
+		2. PM_FEATURE_OVERTEMP_VALUE = 2, the user can configure the
+		over temperature limit in Degree Celsius.
+		3. PM_FEATURE_EXTWDT_STATUS = 3, the user can enable or disable
+		the external watchdog feature.
+		4. PM_FEATURE_EXTWDT_VALUE = 4, the user can configure the
+		external watchdog feature.
+
+		Usage:
+
+		Enable over temperature feature
+		# echo 1 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_id
+		# echo 1 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+
+		Check whether the over temperature feature is enabled or not
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+		The expected result is 1.
+
+		Disable over temperature feature
+		# echo 1 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_id
+		# echo 0 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+
+		Check whether the over temperature feature is disabled or not
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+		The expected result is 0.
+
+		Configure over temperature limit to 50 Degree Celsius
+		# echo 2 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_id
+		# echo 50 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+
+		Check whether the over temperature limit is configured or not
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+		The expected result is 50.
+
+		Enable external watchdog feature
+		# echo 3 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_id
+		# echo 1 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+
+		Check whether the external watchdog feature is enabled or not
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+		The expected result is 1.
+
+		Disable external watchdog feature
+		# echo 3 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_id
+		# echo 0 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+
+		Check whether the external watchdog feature is disabled or not
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+		The expected result is 0.
+
+		Configure external watchdog timer interval to 500ms
+		# echo 4 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_id
+		# echo 500 > /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+
+		Check whether the external watchdog timer interval is configured or not
+		# cat /sys/devices/platform/firmware\:zynqmp-firmware/feature_config_value
+		The expected result is 500.
+
+Users:		Xilinx
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/configfs-usb-gadget-uvc
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/configfs-usb-gadget-uvc
@@ -51,7 +51,7 @@
 KernelVersion:	4.0
 Description:	Default output terminal descriptors
 
-		All attributes read only:
+		All attributes read only except bSourceID:
 
 		==============	=============================================
 		iTerminal	index of string descriptor
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/debugfs-aufs
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/debugfs-aufs
@@ -0,0 +1,55 @@
+What:		/debug/aufs/si_<id>/
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		Under /debug/aufs, a directory named si_<id> is created
+		per aufs mount, where <id> is a unique id generated
+		internally.
+
+What:		/debug/aufs/si_<id>/plink
+Date:		Apr 2013
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It has three lines and shows the information about the
+		pseudo-link. The first line is a single number
+		representing a number of buckets. The second line is a
+		number of pseudo-links per buckets (separated by a
+		blank). The last line is a single number representing a
+		total number of psedo-links.
+		When the aufs mount option 'noplink' is specified, it
+		will show "1\n0\n0\n".
+
+What:		/debug/aufs/si_<id>/xib
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It shows the consumed blocks by xib (External Inode Number
+		Bitmap), its block size and file size.
+		When the aufs mount option 'noxino' is specified, it
+		will be empty. About XINO files, see the aufs manual.
+
+What:		/debug/aufs/si_<id>/xi<branch-index>
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It shows the consumed blocks by xino (External Inode Number
+		Translation Table), its link count, block size and file
+		size.
+		Due to the file size limit, there may exist multiple
+		xino files per branch.  In this case, "-N" is added to
+		the filename and it corresponds to the index of the
+		internal xino array.  "-0" is omitted.
+		When the aufs mount option 'noxino' is specified, Those
+		entries won't exist.  About XINO files, see the aufs
+		manual.
+
+What:		/debug/aufs/si_<id>/xigen
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It shows the consumed blocks by xigen (External Inode
+		Generation Table), its block size and file size.
+		If CONFIG_AUFS_EXPORT is disabled, this entry will not
+		be created.
+		When the aufs mount option 'noxino' is specified, it
+		will be empty. About XINO files, see the aufs manual.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-ata
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-ata
@@ -107,13 +107,14 @@
 				described in ATA8 7.16 and 7.17. Only valid if
 				the device is not a PM.
 
-		pio_mode:	(RO) Transfer modes supported by the device when
-				in PIO mode. Mostly used by PATA device.
+		pio_mode:	(RO) PIO transfer mode used by the device.
+				Mostly used by PATA devices.
 
-		xfer_mode:	(RO) Current transfer mode
+		xfer_mode:	(RO) Current transfer mode. Mostly used by
+				PATA devices.
 
-		dma_mode:	(RO) Transfer modes supported by the device when
-				in DMA mode. Mostly used by PATA device.
+		dma_mode:	(RO) DMA transfer mode used by the device.
+				Mostly used by PATA devices.
 
 		class:		(RO) Device class. Can be "ata" for disk,
 				"atapi" for packet device, "pmp" for PM, or
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-aufs
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-aufs
@@ -0,0 +1,31 @@
+What:		/sys/fs/aufs/si_<id>/
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		Under /sys/fs/aufs, a directory named si_<id> is created
+		per aufs mount, where <id> is a unique id generated
+		internally.
+
+What:		/sys/fs/aufs/si_<id>/br<idx>
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It shows the abolute path of a member directory (which
+		is called branch) in aufs, and its permission.
+
+What:		/sys/fs/aufs/si_<id>/brid<idx>
+Date:		July 2013
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It shows the id of a member directory (which is called
+		branch) in aufs.
+
+What:		/sys/fs/aufs/si_<id>/xi_path
+Date:		March 2009
+Contact:	J. R. Okajima <hooanon05g@gmail.com>
+Description:
+		It shows the abolute path of XINO (External Inode Number
+		Bitmap, Translation Table and Generation Table) file
+		even if it is the default path.
+		When the aufs mount option 'noxino' is specified, it
+		will be empty. About XINO files, see the aufs manual.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-bus-iio
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-bus-iio
@@ -188,7 +188,7 @@
 		Raw capacitance measurement from channel Y. Units after
 		application of scale and offset are nanofarads.
 
-What:		/sys/.../iio:deviceX/in_capacitanceY-in_capacitanceZ_raw
+What:		/sys/.../iio:deviceX/in_capacitanceY-capacitanceZ_raw
 KernelVersion:	3.2
 Contact:	linux-iio@vger.kernel.org
 Description:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-bus-iio-vf610
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-bus-iio-vf610
@@ -1,4 +1,4 @@
-What:		/sys/bus/iio/devices/iio:deviceX/conversion_mode
+What:		/sys/bus/iio/devices/iio:deviceX/in_conversion_mode
 KernelVersion:	4.2
 Contact:	linux-iio@vger.kernel.org
 Description:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-bus-optee-devices
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-bus-optee-devices
@@ -6,3 +6,12 @@
 		OP-TEE bus provides reference to registered drivers under this directory. The <uuid>
 		matches Trusted Application (TA) driver and corresponding TA in secure OS. Drivers
 		are free to create needed API under optee-ta-<uuid> directory.
+
+What:		/sys/bus/tee/devices/optee-ta-<uuid>/need_supplicant
+Date:		November 2023
+KernelVersion:	6.7
+Contact:	op-tee@lists.trustedfirmware.org
+Description:
+		Allows to distinguish whether an OP-TEE based TA/device requires user-space
+		tee-supplicant to function properly or not. This attribute will be present for
+		devices which depend on tee-supplicant to be running.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-bus-pci
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-bus-pci
@@ -148,6 +148,17 @@
 		will be present in sysfs.  Writing 1 to this file
 		will perform reset.
 
+What:		/sys/bus/pci/devices/.../reset_subordinate
+Date:		October 2024
+Contact:	linux-pci@vger.kernel.org
+Description:
+		This is visible only for bridge devices. If you want to reset
+		all devices attached through the subordinate bus of a specific
+		bridge device, writing 1 to this will try to do it.  This will
+		affect all devices attached to the system through this bridge
+		similiar to writing 1 to their individual "reset" file, so use
+		with caution.
+
 What:		/sys/bus/pci/devices/.../vpd
 Date:		February 2008
 Contact:	Ben Hutchings <bwh@kernel.org>
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-bus-spi-devices-spi-nor
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-bus-spi-devices-spi-nor
@@ -5,6 +5,9 @@
 Description:	(RO) The JEDEC ID of the SPI NOR flash as reported by the
 		flash device.
 
+		The attribute is not present if the flash doesn't support
+		the "Read JEDEC ID" command (9Fh). This is the case for
+		non-JEDEC compliant flashes.
 
 What:		/sys/bus/spi/devices/.../spi-nor/manufacturer
 Date:		April 2021
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-class-devfreq
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-class-devfreq
@@ -52,6 +52,9 @@
 
 			echo 0 > /sys/class/devfreq/.../trans_stat
 
+		If the transition table is bigger than PAGE_SIZE, reading
+		this will return an -EFBIG error.
+
 What:		/sys/class/devfreq/.../available_frequencies
 Date:		October 2012
 Contact:	Nishanth Menon <nm@ti.com>
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-class-fpga-bridge
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-class-fpga-bridge
@@ -9,3 +9,12 @@
 KernelVersion:	4.5
 Contact:	Alan Tull <atull@opensource.altera.com>
 Description:	Show bridge state as "enabled" or "disabled"
+
+What:		/sys/class/fpga_bridge/<bridge>/set
+Date:		January 2017
+KernelVersion:	4.9
+Contact:	Michal Simek <michal.simek@xilinx.com>
+Description:	Manual set bridge state (0-disable, !0 enable).
+		Enabling this option requires that the module is
+		compiled with #define DEBUG which is enabled by default
+		when CONFIG_DEBUG_KERNEL is setup.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-class-net-queues
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-class-net-queues
@@ -1,4 +1,4 @@
-What:		/sys/class/<iface>/queues/rx-<queue>/rps_cpus
+What:		/sys/class/net/<iface>/queues/rx-<queue>/rps_cpus
 Date:		March 2010
 KernelVersion:	2.6.35
 Contact:	netdev@vger.kernel.org
@@ -8,7 +8,7 @@
 		network device queue. Possible values depend on the number
 		of available CPU(s) in the system.
 
-What:		/sys/class/<iface>/queues/rx-<queue>/rps_flow_cnt
+What:		/sys/class/net/<iface>/queues/rx-<queue>/rps_flow_cnt
 Date:		April 2010
 KernelVersion:	2.6.35
 Contact:	netdev@vger.kernel.org
@@ -16,7 +16,7 @@
 		Number of Receive Packet Steering flows being currently
 		processed by this particular network device receive queue.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/tx_timeout
+What:		/sys/class/net/<iface>/queues/tx-<queue>/tx_timeout
 Date:		November 2011
 KernelVersion:	3.3
 Contact:	netdev@vger.kernel.org
@@ -24,7 +24,7 @@
 		Indicates the number of transmit timeout events seen by this
 		network interface transmit queue.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/tx_maxrate
+What:		/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
 Date:		March 2015
 KernelVersion:	4.1
 Contact:	netdev@vger.kernel.org
@@ -32,7 +32,7 @@
 		A Mbps max-rate set for the queue, a value of zero means disabled,
 		default is disabled.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/xps_cpus
+What:		/sys/class/net/<iface>/queues/tx-<queue>/xps_cpus
 Date:		November 2010
 KernelVersion:	2.6.38
 Contact:	netdev@vger.kernel.org
@@ -42,7 +42,7 @@
 		network device transmit queue. Possible vaules depend on the
 		number of available CPU(s) in the system.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/xps_rxqs
+What:		/sys/class/net/<iface>/queues/tx-<queue>/xps_rxqs
 Date:		June 2018
 KernelVersion:	4.18.0
 Contact:	netdev@vger.kernel.org
@@ -53,7 +53,7 @@
 		number of available receive queue(s) in the network device.
 		Default is disabled.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/byte_queue_limits/hold_time
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/hold_time
 Date:		November 2011
 KernelVersion:	3.3
 Contact:	netdev@vger.kernel.org
@@ -62,7 +62,7 @@
 		of this particular network device transmit queue.
 		Default value is 1000.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/byte_queue_limits/inflight
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/inflight
 Date:		November 2011
 KernelVersion:	3.3
 Contact:	netdev@vger.kernel.org
@@ -70,7 +70,7 @@
 		Indicates the number of bytes (objects) in flight on this
 		network device transmit queue.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/byte_queue_limits/limit
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/limit
 Date:		November 2011
 KernelVersion:	3.3
 Contact:	netdev@vger.kernel.org
@@ -79,7 +79,7 @@
 		on this network device transmit queue. This value is clamped
 		to be within the bounds defined by limit_max and limit_min.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/byte_queue_limits/limit_max
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/limit_max
 Date:		November 2011
 KernelVersion:	3.3
 Contact:	netdev@vger.kernel.org
@@ -88,7 +88,7 @@
 		queued on this network device transmit queue. See
 		include/linux/dynamic_queue_limits.h for the default value.
 
-What:		/sys/class/<iface>/queues/tx-<queue>/byte_queue_limits/limit_min
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/limit_min
 Date:		November 2011
 KernelVersion:	3.3
 Contact:	netdev@vger.kernel.org
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-class-net-statistics
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-class-net-statistics
@@ -1,4 +1,4 @@
-What:		/sys/class/<iface>/statistics/collisions
+What:		/sys/class/net/<iface>/statistics/collisions
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -6,7 +6,7 @@
 		Indicates the number of collisions seen by this network device.
 		This value might not be relevant with all MAC layers.
 
-What:		/sys/class/<iface>/statistics/multicast
+What:		/sys/class/net/<iface>/statistics/multicast
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -14,7 +14,7 @@
 		Indicates the number of multicast packets received by this
 		network device.
 
-What:		/sys/class/<iface>/statistics/rx_bytes
+What:		/sys/class/net/<iface>/statistics/rx_bytes
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -23,7 +23,7 @@
 		See the network driver for the exact meaning of when this
 		value is incremented.
 
-What:		/sys/class/<iface>/statistics/rx_compressed
+What:		/sys/class/net/<iface>/statistics/rx_compressed
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -32,7 +32,7 @@
 		network device. This value might only be relevant for interfaces
 		that support packet compression (e.g: PPP).
 
-What:		/sys/class/<iface>/statistics/rx_crc_errors
+What:		/sys/class/net/<iface>/statistics/rx_crc_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -41,7 +41,7 @@
 		by this network device. Note that the specific meaning might
 		depend on the MAC layer used by the interface.
 
-What:		/sys/class/<iface>/statistics/rx_dropped
+What:		/sys/class/net/<iface>/statistics/rx_dropped
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -51,7 +51,7 @@
 		packet processing. See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_errors
+What:		/sys/class/net/<iface>/statistics/rx_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -59,7 +59,7 @@
 		Indicates the number of receive errors on this network device.
 		See the network driver for the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_fifo_errors
+What:		/sys/class/net/<iface>/statistics/rx_fifo_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -68,7 +68,7 @@
 		network device. See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_frame_errors
+What:		/sys/class/net/<iface>/statistics/rx_frame_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -78,7 +78,7 @@
 		on the MAC layer protocol used. See the network driver for
 		the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_length_errors
+What:		/sys/class/net/<iface>/statistics/rx_length_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -87,7 +87,7 @@
 		error, oversized or undersized. See the network driver for the
 		exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_missed_errors
+What:		/sys/class/net/<iface>/statistics/rx_missed_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -96,7 +96,7 @@
 		due to lack of capacity in the receive side. See the network
 		driver for the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_nohandler
+What:		/sys/class/net/<iface>/statistics/rx_nohandler
 Date:		February 2016
 KernelVersion:	4.6
 Contact:	netdev@vger.kernel.org
@@ -104,7 +104,7 @@
 		Indicates the number of received packets that were dropped on
 		an inactive device by the network core.
 
-What:		/sys/class/<iface>/statistics/rx_over_errors
+What:		/sys/class/net/<iface>/statistics/rx_over_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -114,7 +114,7 @@
 		(e.g: larger than MTU). See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_packets
+What:		/sys/class/net/<iface>/statistics/rx_packets
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -122,7 +122,7 @@
 		Indicates the total number of good packets received by this
 		network device.
 
-What:		/sys/class/<iface>/statistics/tx_aborted_errors
+What:		/sys/class/net/<iface>/statistics/tx_aborted_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -132,7 +132,7 @@
 		a medium collision). See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/tx_bytes
+What:		/sys/class/net/<iface>/statistics/tx_bytes
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -143,7 +143,7 @@
 		transmitted packets or all packets that have been queued for
 		transmission.
 
-What:		/sys/class/<iface>/statistics/tx_carrier_errors
+What:		/sys/class/net/<iface>/statistics/tx_carrier_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -152,7 +152,7 @@
 		because of carrier errors (e.g: physical link down). See the
 		network driver for the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/tx_compressed
+What:		/sys/class/net/<iface>/statistics/tx_compressed
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -161,7 +161,7 @@
 		this might only be relevant for devices that support
 		compression (e.g: PPP).
 
-What:		/sys/class/<iface>/statistics/tx_dropped
+What:		/sys/class/net/<iface>/statistics/tx_dropped
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -170,7 +170,7 @@
 		See the driver for the exact reasons as to why the packets were
 		dropped.
 
-What:		/sys/class/<iface>/statistics/tx_errors
+What:		/sys/class/net/<iface>/statistics/tx_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -179,7 +179,7 @@
 		a network device. See the driver for the exact reasons as to
 		why the packets were dropped.
 
-What:		/sys/class/<iface>/statistics/tx_fifo_errors
+What:		/sys/class/net/<iface>/statistics/tx_fifo_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -188,7 +188,7 @@
 		FIFO error. See the driver for the exact reasons as to why the
 		packets were dropped.
 
-What:		/sys/class/<iface>/statistics/tx_heartbeat_errors
+What:		/sys/class/net/<iface>/statistics/tx_heartbeat_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -197,7 +197,7 @@
 		reported as heartbeat errors. See the driver for the exact
 		reasons as to why the packets were dropped.
 
-What:		/sys/class/<iface>/statistics/tx_packets
+What:		/sys/class/net/<iface>/statistics/tx_packets
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -206,7 +206,7 @@
 		device. See the driver for whether this reports the number of all
 		attempted or successful transmissions.
 
-What:		/sys/class/<iface>/statistics/tx_window_errors
+What:		/sys/class/net/<iface>/statistics/tx_window_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-devices-system-cpu
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-devices-system-cpu
@@ -511,15 +511,19 @@
 		cpu_capacity: capacity of cpu#.
 
 What:		/sys/devices/system/cpu/vulnerabilities
+		/sys/devices/system/cpu/vulnerabilities/gather_data_sampling
+		/sys/devices/system/cpu/vulnerabilities/itlb_multihit
+		/sys/devices/system/cpu/vulnerabilities/l1tf
+		/sys/devices/system/cpu/vulnerabilities/mds
 		/sys/devices/system/cpu/vulnerabilities/meltdown
+		/sys/devices/system/cpu/vulnerabilities/mmio_stale_data
+		/sys/devices/system/cpu/vulnerabilities/reg_file_data_sampling
+		/sys/devices/system/cpu/vulnerabilities/retbleed
+		/sys/devices/system/cpu/vulnerabilities/spec_store_bypass
 		/sys/devices/system/cpu/vulnerabilities/spectre_v1
 		/sys/devices/system/cpu/vulnerabilities/spectre_v2
-		/sys/devices/system/cpu/vulnerabilities/spec_store_bypass
-		/sys/devices/system/cpu/vulnerabilities/l1tf
-		/sys/devices/system/cpu/vulnerabilities/mds
 		/sys/devices/system/cpu/vulnerabilities/srbds
 		/sys/devices/system/cpu/vulnerabilities/tsx_async_abort
-		/sys/devices/system/cpu/vulnerabilities/itlb_multihit
 Date:		January 2018
 Contact:	Linux kernel mailing list <linux-kernel@vger.kernel.org>
 Description:	Information about CPU vulnerabilities
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-driver-cortexa53-edac
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-driver-cortexa53-edac
@@ -0,0 +1,10 @@
+What:		/sys/devices/system/edac/cpu_cache/inject_(L1/L2)_Cache_Error
+Date:		June 2016
+Contact:	nagasure@xilinx.com
+		punnaia@xilinx.com
+Description:    This control file allows to inject cache errors on cortexa53
+		L1 and L2 caches. arm provided error injection for cortexa53
+		caches (L1 and L2). Just echo 1 > /sys/devices/system/edac/
+		cpu_cache/inject_L1_Error for L1 cache error injection and
+		echo 1 > /sys/devices/system/edac/cpu_cache/inject_L2_Error
+		for L2 cache error injection.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-driver-xen-blkback
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-driver-xen-blkback
@@ -42,5 +42,5 @@
 Contact:        SeongJae Park <sjpark@amazon.de>
 Description:
                 Whether to enable the persistent grants feature or not.  Note
-                that this option only takes effect on newly created backends.
+                that this option only takes effect on newly connected backends.
                 The default is Y (enable).
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-driver-xen-blkfront
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-driver-xen-blkfront
@@ -15,5 +15,5 @@
 Contact:        SeongJae Park <sjpark@amazon.de>
 Description:
                 Whether to enable the persistent grants feature or not.  Note
-                that this option only takes effect on newly created frontends.
+                that this option only takes effect on newly connected frontends.
                 The default is Y (enable).
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-driver-xilinx-tmr-inject
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-driver-xilinx-tmr-inject
@@ -0,0 +1,12 @@
+What:		/sys/devices/platform/amba_pl/<dev>/inject_err
+Date:		Feb 2022
+Contact:	appana.durga.rao@xilinx.com
+Description:	This control file allows to inject fault using tmr inject.
+		This file is write only.
+
+What:		/sys/devices/platform/amba_pl/<dev>/inject_cpuid
+Date:		Feb 2022
+Contact:	appana.durga.rao@xilinx.com
+Description:	This control file allows to configure the CPU identifier
+		to enable fault injection.
+		This file is write only.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-driver-xilinx-tmr-manager
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-driver-xilinx-tmr-manager
@@ -0,0 +1,18 @@
+What:		/sys/devices/platform/amba_pl/<dev>/status
+Date:		Feb 2022
+Contact:	appana.durga.rao@xilinx.com
+Description:	This control file provides the status of the tmr manager
+		useful for getting the status of fault.
+		This file cannot be written.
+
+What:		/sys/devices/platform/amba_pl/<dev>/errcnt
+Date:		Feb 2022
+Contact:	appana.durga.rao@xilinx.com
+Description:	This control file provides the fault detection count.
+		This file cannot be written.
+
+What:		/sys/devices/platform/amba_pl/<dev>/dis_block_break
+Date:		Feb 2022
+Contact:	appana.durga.rao@xilinx.com
+Description:	This control file enables the break signal.
+		This file is write only.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-fs-f2fs
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-fs-f2fs
@@ -55,8 +55,9 @@
 		0x04  F2FS_IPU_UTIL
 		0x08  F2FS_IPU_SSR_UTIL
 		0x10  F2FS_IPU_FSYNC
-		0x20  F2FS_IPU_ASYNC,
+		0x20  F2FS_IPU_ASYNC
 		0x40  F2FS_IPU_NOCACHE
+		0x80  F2FS_IPU_HONOR_OPU_WRITE
 		====  =================
 
 		Refer segment.h for details.
@@ -425,6 +426,7 @@
 		0x800  SBI_QUOTA_SKIP_FLUSH  skip flushing quota in current CP
 		0x1000 SBI_QUOTA_NEED_REPAIR quota file may be corrupted
 		0x2000 SBI_IS_RESIZEFS       resizefs is in process
+		0x4000 SBI_IS_FREEZING       freefs is in process
 		====== ===================== =================================
 
 What:		/sys/fs/f2fs/<disk>/ckpt_thread_ioprio
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-kernel-oops_count
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-kernel-oops_count
@@ -0,0 +1,6 @@
+What:		/sys/kernel/oops_count
+Date:		November 2022
+KernelVersion:	6.2.0
+Contact:	Linux Kernel Hardening List <linux-hardening@vger.kernel.org>
+Description:
+		Shows how many times the system has Oopsed since last boot.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-kernel-warn_count
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-kernel-warn_count
@@ -0,0 +1,6 @@
+What:		/sys/kernel/warn_count
+Date:		November 2022
+KernelVersion:	6.2.0
+Contact:	Linux Kernel Hardening List <linux-hardening@vger.kernel.org>
+Description:
+		Shows how many times the system has Warned since last boot.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/ABI/testing/sysfs-platform-asus-wmi
+++ linux-xilinx-zynqmp-5.15.0/Documentation/ABI/testing/sysfs-platform-asus-wmi
@@ -57,3 +57,12 @@
 			* 0 - default,
 			* 1 - overboost,
 			* 2 - silent
+
+What:		/sys/devices/platform/<platform>/dgpu_disable
+Date:		Aug 2022
+KernelVersion:	5.17
+Contact:	"Luke Jones" <luke@ljones.dev>
+Description:
+		Disable discrete GPU:
+			* 0 - Enable dGPU,
+			* 1 - Disable dGPU
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/Makefile
+++ linux-xilinx-zynqmp-5.15.0/Documentation/Makefile
@@ -87,7 +87,7 @@
 	$(abspath $(BUILDDIR)/$3/$4)
 
 htmldocs:
-	@$(srctree)/scripts/sphinx-pre-install --version-check
+	@$(srctree)/scripts/sphinx-pre-install --version-check --no-virtualenv
 	@+$(foreach var,$(SPHINXDIRS),$(call loop_cmd,sphinx,html,$(var),,$(var)))
 
 linkcheckdocs:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/accounting/psi.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/accounting/psi.rst
@@ -37,11 +37,7 @@
 Pressure information for each resource is exported through the
 respective file in /proc/pressure/ -- cpu, memory, and io.
 
-The format for CPU is as such::
-
-	some avg10=0.00 avg60=0.00 avg300=0.00 total=0
-
-and for memory and IO::
+The format is as such::
 
 	some avg10=0.00 avg60=0.00 avg300=0.00 total=0
 	full avg10=0.00 avg60=0.00 avg300=0.00 total=0
@@ -58,6 +54,9 @@
 still doing productive work. As such, time spent in this subset of the
 stall state is tracked separately and exported in the "full" averages.
 
+CPU full is undefined at the system level, but has been reported
+since 5.13, so it is set to zero for backward compatibility.
+
 The ratios (in %) are tracked as recent trends over ten, sixty, and
 three hundred second windows, which gives insight into short term events
 as well as medium and long term trends. The total absolute stall time
@@ -92,7 +91,8 @@
 for the same psi metric can be specified. However for each trigger a separate
 file descriptor is required to be able to poll it separately from others,
 therefore for each trigger a separate open() syscall should be made even
-when opening the same psi interface file.
+when opening the same psi interface file. Write operations to a file descriptor
+with an already existing psi trigger will fail with EBUSY.
 
 Monitors activate only when system enters stall state for the monitored
 psi metric and deactivates upon exit from the stall state. While system is
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/acpi/cppc_sysfs.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/acpi/cppc_sysfs.rst
@@ -4,6 +4,8 @@
 Collaborative Processor Performance Control (CPPC)
 ==================================================
 
+.. _cppc_sysfs:
+
 CPPC
 ====
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/cgroup-v1/memory.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/cgroup-v1/memory.rst
@@ -84,6 +84,8 @@
  memory.swappiness		     set/show swappiness parameter of vmscan
 				     (See sysctl's vm.swappiness)
  memory.move_charge_at_immigrate     set/show controls of moving charges
+                                     This knob is deprecated and shouldn't be
+                                     used.
  memory.oom_control		     set/show oom controls.
  memory.numa_stat		     show the number of memory usage per numa
 				     node
@@ -723,8 +725,15 @@
        It is recommended to set the soft limit always below the hard limit,
        otherwise the hard limit will take precedence.
 
-8. Move charges at task migration
-=================================
+8. Move charges at task migration (DEPRECATED!)
+===============================================
+
+THIS IS DEPRECATED!
+
+It's expensive and unreliable! It's better practice to launch workload
+tasks directly from inside their target cgroup. Use dedicated workload
+cgroups to allow fine-grained policy adjustments without having to
+move physical pages between control domains.
 
 Users can move charges associated with a task along with task migration, that
 is, uncharge task's pages from the old cgroup and charge them to the new cgroup.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/cifs/usage.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/cifs/usage.rst
@@ -734,10 +734,9 @@
 			using weaker password hashes is 0x37037 (lanman,
 			plaintext, ntlm, ntlmv2, signing allowed).  Some
 			SecurityFlags require the corresponding menuconfig
-			options to be enabled (lanman and plaintext require
-			CONFIG_CIFS_WEAK_PW_HASH for example).  Enabling
-			plaintext authentication currently requires also
-			enabling lanman authentication in the security flags
+			options to be enabled.  Enabling plaintext
+			authentication currently requires also enabling
+			lanman authentication in the security flags
 			because the cifs module only supports sending
 			laintext passwords using the older lanman dialect
 			form of the session setup SMB.  (e.g. for authentication
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/device-mapper/dm-init.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/device-mapper/dm-init.rst
@@ -123,3 +123,11 @@
     0 1638400 verity 1 8:1 8:2 4096 4096 204800 1 sha256
     fb1a5a0f00deb908d8b53cb270858975e76cf64105d412ce764225d53b8f3cfd
     51934789604d1b92399c52e7cb149d1b3a1b74bbbcb103b2a0aaacbed5c08584
+
+For setups using device-mapper on top of asynchronously probed block
+devices (MMC, USB, ..), it may be necessary to tell dm-init to
+explicitly wait for them to become available before setting up the
+device-mapper tables. This can be done with the "dm-mod.waitfor="
+module parameter, which takes a list of devices to wait for::
+
+  dm-mod.waitfor=<device1>[,..,<deviceN>]
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/device-mapper/writecache.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/device-mapper/writecache.rst
@@ -78,16 +78,16 @@
 2. the number of blocks
 3. the number of free blocks
 4. the number of blocks under writeback
-5. the number of read requests
-6. the number of read requests that hit the cache
-7. the number of write requests
-8. the number of write requests that hit uncommitted block
-9. the number of write requests that hit committed block
-10. the number of write requests that bypass the cache
-11. the number of write requests that are allocated in the cache
+5. the number of read blocks
+6. the number of read blocks that hit the cache
+7. the number of write blocks
+8. the number of write blocks that hit uncommitted block
+9. the number of write blocks that hit committed block
+10. the number of write blocks that bypass the cache
+11. the number of write blocks that are allocated in the cache
 12. the number of write requests that are blocked on the freelist
 13. the number of flush requests
-14. the number of discard requests
+14. the number of discarded blocks
 
 Messages:
 	flush
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/devices.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/devices.txt
@@ -2339,13 +2339,7 @@
 		disks (see major number 3) except that the limit on
 		partitions is 31.
 
- 162 char	Raw block device interface
-		  0 = /dev/rawctl	Raw I/O control device
-		  1 = /dev/raw/raw1	First raw I/O device
-		  2 = /dev/raw/raw2	Second raw I/O device
-		    ...
-		 max minor number of raw device is set by kernel config
-		 MAX_RAW_DEVS or raw module parameter 'max_raw_devs'
+ 162 char	Used for (now removed) raw block device interface
 
  163 char
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/filesystem-monitoring.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/filesystem-monitoring.rst
@@ -0,0 +1,78 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================================
+File system Monitoring with fanotify
+====================================
+
+File system Error Reporting
+===========================
+
+Fanotify supports the FAN_FS_ERROR event type for file system-wide error
+reporting.  It is meant to be used by file system health monitoring
+daemons, which listen for these events and take actions (notify
+sysadmin, start recovery) when a file system problem is detected.
+
+By design, a FAN_FS_ERROR notification exposes sufficient information
+for a monitoring tool to know a problem in the file system has happened.
+It doesn't necessarily provide a user space application with semantics
+to verify an IO operation was successfully executed.  That is out of
+scope for this feature.  Instead, it is only meant as a framework for
+early file system problem detection and reporting recovery tools.
+
+When a file system operation fails, it is common for dozens of kernel
+errors to cascade after the initial failure, hiding the original failure
+log, which is usually the most useful debug data to troubleshoot the
+problem.  For this reason, FAN_FS_ERROR tries to report only the first
+error that occurred for a file system since the last notification, and
+it simply counts additional errors.  This ensures that the most
+important pieces of information are never lost.
+
+FAN_FS_ERROR requires the fanotify group to be setup with the
+FAN_REPORT_FID flag.
+
+At the time of this writing, the only file system that emits FAN_FS_ERROR
+notifications is Ext4.
+
+A FAN_FS_ERROR Notification has the following format::
+
+  ::
+
+     [ Notification Metadata (Mandatory) ]
+     [ Generic Error Record  (Mandatory) ]
+     [ FID record            (Mandatory) ]
+
+The order of records is not guaranteed, and new records might be added
+in the future.  Therefore, applications must not rely on the order and
+must be prepared to skip over unknown records. Please refer to
+``samples/fanotify/fs-monitor.c`` for an example parser.
+
+Generic error record
+--------------------
+
+The generic error record provides enough information for a file system
+agnostic tool to learn about a problem in the file system, without
+providing any additional details about the problem.  This record is
+identified by ``struct fanotify_event_info_header.info_type`` being set
+to FAN_EVENT_INFO_TYPE_ERROR.
+
+  ::
+
+     struct fanotify_event_info_error {
+          struct fanotify_event_info_header hdr;
+         __s32 error;
+         __u32 error_count;
+     };
+
+The `error` field identifies the type of error using errno values.
+`error_count` tracks the number of errors that occurred and were
+suppressed to preserve the original error information, since the last
+notification.
+
+FID record
+----------
+
+The FID record can be used to uniquely identify the inode that triggered
+the error through the combination of fsid and file handle.  A file system
+specific application can use that information to attempt a recovery
+procedure.  Errors that are not related to an inode are reported with an
+empty file handle of type FILEID_INVALID.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/core-scheduling.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/core-scheduling.rst
@@ -66,8 +66,8 @@
     will be performed for all tasks in the task group of ``pid``.
 
 arg5:
-    userspace pointer to an unsigned long for storing the cookie returned by
-    ``PR_SCHED_CORE_GET`` command. Should be 0 for all other commands.
+    userspace pointer to an unsigned long long for storing the cookie returned
+    by ``PR_SCHED_CORE_GET`` command. Should be 0 for all other commands.
 
 In order for a process to push a cookie to, or pull a cookie from a process, it
 is required to have the ptrace access mode: `PTRACE_MODE_READ_REALCREDS` to the
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/cross-thread-rsb.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/cross-thread-rsb.rst
@@ -0,0 +1,92 @@
+
+.. SPDX-License-Identifier: GPL-2.0
+
+Cross-Thread Return Address Predictions
+=======================================
+
+Certain AMD and Hygon processors are subject to a cross-thread return address
+predictions vulnerability. When running in SMT mode and one sibling thread
+transitions out of C0 state, the other sibling thread could use return target
+predictions from the sibling thread that transitioned out of C0.
+
+The Spectre v2 mitigations protect the Linux kernel, as it fills the return
+address prediction entries with safe targets when context switching to the idle
+thread. However, KVM does allow a VMM to prevent exiting guest mode when
+transitioning out of C0. This could result in a guest-controlled return target
+being consumed by the sibling thread.
+
+Affected processors
+-------------------
+
+The following CPUs are vulnerable:
+
+    - AMD Family 17h processors
+    - Hygon Family 18h processors
+
+Related CVEs
+------------
+
+The following CVE entry is related to this issue:
+
+   ==============  =======================================
+   CVE-2022-27672  Cross-Thread Return Address Predictions
+   ==============  =======================================
+
+Problem
+-------
+
+Affected SMT-capable processors support 1T and 2T modes of execution when SMT
+is enabled. In 2T mode, both threads in a core are executing code. For the
+processor core to enter 1T mode, it is required that one of the threads
+requests to transition out of the C0 state. This can be communicated with the
+HLT instruction or with an MWAIT instruction that requests non-C0.
+When the thread re-enters the C0 state, the processor transitions back
+to 2T mode, assuming the other thread is also still in C0 state.
+
+In affected processors, the return address predictor (RAP) is partitioned
+depending on the SMT mode. For instance, in 2T mode each thread uses a private
+16-entry RAP, but in 1T mode, the active thread uses a 32-entry RAP. Upon
+transition between 1T/2T mode, the RAP contents are not modified but the RAP
+pointers (which control the next return target to use for predictions) may
+change. This behavior may result in return targets from one SMT thread being
+used by RET predictions in the sibling thread following a 1T/2T switch. In
+particular, a RET instruction executed immediately after a transition to 1T may
+use a return target from the thread that just became idle. In theory, this
+could lead to information disclosure if the return targets used do not come
+from trustworthy code.
+
+Attack scenarios
+----------------
+
+An attack can be mounted on affected processors by performing a series of CALL
+instructions with targeted return locations and then transitioning out of C0
+state.
+
+Mitigation mechanism
+--------------------
+
+Before entering idle state, the kernel context switches to the idle thread. The
+context switch fills the RAP entries (referred to as the RSB in Linux) with safe
+targets by performing a sequence of CALL instructions.
+
+Prevent a guest VM from directly putting the processor into an idle state by
+intercepting HLT and MWAIT instructions.
+
+Both mitigations are required to fully address this issue.
+
+Mitigation control on the kernel command line
+---------------------------------------------
+
+Use existing Spectre v2 mitigations that will fill the RSB on context switch.
+
+Mitigation control for KVM - module parameter
+---------------------------------------------
+
+By default, the KVM hypervisor mitigates this issue by intercepting guest
+attempts to transition out of C0. A VMM can use the KVM_CAP_X86_DISABLE_EXITS
+capability to override those interceptions, but since this is not common, the
+mitigation that covers this path is not enabled by default.
+
+The mitigation for the KVM_CAP_X86_DISABLE_EXITS capability can be turned on
+using the boolean module parameter mitigate_smt_rsb, e.g.:
+        kvm.mitigate_smt_rsb=1
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/gather_data_sampling.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/gather_data_sampling.rst
@@ -0,0 +1,109 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+GDS - Gather Data Sampling
+==========================
+
+Gather Data Sampling is a hardware vulnerability which allows unprivileged
+speculative access to data which was previously stored in vector registers.
+
+Problem
+-------
+When a gather instruction performs loads from memory, different data elements
+are merged into the destination vector register. However, when a gather
+instruction that is transiently executed encounters a fault, stale data from
+architectural or internal vector registers may get transiently forwarded to the
+destination vector register instead. This will allow a malicious attacker to
+infer stale data using typical side channel techniques like cache timing
+attacks. GDS is a purely sampling-based attack.
+
+The attacker uses gather instructions to infer the stale vector register data.
+The victim does not need to do anything special other than use the vector
+registers. The victim does not need to use gather instructions to be
+vulnerable.
+
+Because the buffers are shared between Hyper-Threads cross Hyper-Thread attacks
+are possible.
+
+Attack scenarios
+----------------
+Without mitigation, GDS can infer stale data across virtually all
+permission boundaries:
+
+	Non-enclaves can infer SGX enclave data
+	Userspace can infer kernel data
+	Guests can infer data from hosts
+	Guest can infer guest from other guests
+	Users can infer data from other users
+
+Because of this, it is important to ensure that the mitigation stays enabled in
+lower-privilege contexts like guests and when running outside SGX enclaves.
+
+The hardware enforces the mitigation for SGX. Likewise, VMMs should  ensure
+that guests are not allowed to disable the GDS mitigation. If a host erred and
+allowed this, a guest could theoretically disable GDS mitigation, mount an
+attack, and re-enable it.
+
+Mitigation mechanism
+--------------------
+This issue is mitigated in microcode. The microcode defines the following new
+bits:
+
+ ================================   ===   ============================
+ IA32_ARCH_CAPABILITIES[GDS_CTRL]   R/O   Enumerates GDS vulnerability
+                                          and mitigation support.
+ IA32_ARCH_CAPABILITIES[GDS_NO]     R/O   Processor is not vulnerable.
+ IA32_MCU_OPT_CTRL[GDS_MITG_DIS]    R/W   Disables the mitigation
+                                          0 by default.
+ IA32_MCU_OPT_CTRL[GDS_MITG_LOCK]   R/W   Locks GDS_MITG_DIS=0. Writes
+                                          to GDS_MITG_DIS are ignored
+                                          Can't be cleared once set.
+ ================================   ===   ============================
+
+GDS can also be mitigated on systems that don't have updated microcode by
+disabling AVX. This can be done by setting gather_data_sampling="force" or
+"clearcpuid=avx" on the kernel command-line.
+
+If used, these options will disable AVX use by turning off XSAVE YMM support.
+However, the processor will still enumerate AVX support.  Userspace that
+does not follow proper AVX enumeration to check both AVX *and* XSAVE YMM
+support will break.
+
+Mitigation control on the kernel command line
+---------------------------------------------
+The mitigation can be disabled by setting "gather_data_sampling=off" or
+"mitigations=off" on the kernel command line. Not specifying either will default
+to the mitigation being enabled. Specifying "gather_data_sampling=force" will
+use the microcode mitigation when available or disable AVX on affected systems
+where the microcode hasn't been updated to include the mitigation.
+
+GDS System Information
+------------------------
+The kernel provides vulnerability status information through sysfs. For
+GDS this can be accessed by the following sysfs file:
+
+/sys/devices/system/cpu/vulnerabilities/gather_data_sampling
+
+The possible values contained in this file are:
+
+ ============================== =============================================
+ Not affected                   Processor not vulnerable.
+ Vulnerable                     Processor vulnerable and mitigation disabled.
+ Vulnerable: No microcode       Processor vulnerable and microcode is missing
+                                mitigation.
+ Mitigation: AVX disabled,
+ no microcode                   Processor is vulnerable and microcode is missing
+                                mitigation. AVX disabled as mitigation.
+ Mitigation: Microcode          Processor is vulnerable and mitigation is in
+                                effect.
+ Mitigation: Microcode (locked) Processor is vulnerable and mitigation is in
+                                effect and cannot be disabled.
+ Unknown: Dependent on
+ hypervisor status              Running on a virtual guest processor that is
+                                affected but with no way to know if host
+                                processor is mitigated or vulnerable.
+ ============================== =============================================
+
+GDS Default mitigation
+----------------------
+The updated microcode will enable the mitigation by default. The kernel's
+default action is to leave the mitigation enabled.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/index.rst
@@ -17,3 +17,8 @@
    special-register-buffer-data-sampling.rst
    core-scheduling.rst
    l1d_flush.rst
+   processor_mmio_stale_data.rst
+   cross-thread-rsb.rst
+   gather_data_sampling.rst
+   srso
+   reg-file-data-sampling
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/processor_mmio_stale_data.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/processor_mmio_stale_data.rst
@@ -0,0 +1,260 @@
+=========================================
+Processor MMIO Stale Data Vulnerabilities
+=========================================
+
+Processor MMIO Stale Data Vulnerabilities are a class of memory-mapped I/O
+(MMIO) vulnerabilities that can expose data. The sequences of operations for
+exposing data range from simple to very complex. Because most of the
+vulnerabilities require the attacker to have access to MMIO, many environments
+are not affected. System environments using virtualization where MMIO access is
+provided to untrusted guests may need mitigation. These vulnerabilities are
+not transient execution attacks. However, these vulnerabilities may propagate
+stale data into core fill buffers where the data can subsequently be inferred
+by an unmitigated transient execution attack. Mitigation for these
+vulnerabilities includes a combination of microcode update and software
+changes, depending on the platform and usage model. Some of these mitigations
+are similar to those used to mitigate Microarchitectural Data Sampling (MDS) or
+those used to mitigate Special Register Buffer Data Sampling (SRBDS).
+
+Data Propagators
+================
+Propagators are operations that result in stale data being copied or moved from
+one microarchitectural buffer or register to another. Processor MMIO Stale Data
+Vulnerabilities are operations that may result in stale data being directly
+read into an architectural, software-visible state or sampled from a buffer or
+register.
+
+Fill Buffer Stale Data Propagator (FBSDP)
+-----------------------------------------
+Stale data may propagate from fill buffers (FB) into the non-coherent portion
+of the uncore on some non-coherent writes. Fill buffer propagation by itself
+does not make stale data architecturally visible. Stale data must be propagated
+to a location where it is subject to reading or sampling.
+
+Sideband Stale Data Propagator (SSDP)
+-------------------------------------
+The sideband stale data propagator (SSDP) is limited to the client (including
+Intel Xeon server E3) uncore implementation. The sideband response buffer is
+shared by all client cores. For non-coherent reads that go to sideband
+destinations, the uncore logic returns 64 bytes of data to the core, including
+both requested data and unrequested stale data, from a transaction buffer and
+the sideband response buffer. As a result, stale data from the sideband
+response and transaction buffers may now reside in a core fill buffer.
+
+Primary Stale Data Propagator (PSDP)
+------------------------------------
+The primary stale data propagator (PSDP) is limited to the client (including
+Intel Xeon server E3) uncore implementation. Similar to the sideband response
+buffer, the primary response buffer is shared by all client cores. For some
+processors, MMIO primary reads will return 64 bytes of data to the core fill
+buffer including both requested data and unrequested stale data. This is
+similar to the sideband stale data propagator.
+
+Vulnerabilities
+===============
+Device Register Partial Write (DRPW) (CVE-2022-21166)
+-----------------------------------------------------
+Some endpoint MMIO registers incorrectly handle writes that are smaller than
+the register size. Instead of aborting the write or only copying the correct
+subset of bytes (for example, 2 bytes for a 2-byte write), more bytes than
+specified by the write transaction may be written to the register. On
+processors affected by FBSDP, this may expose stale data from the fill buffers
+of the core that created the write transaction.
+
+Shared Buffers Data Sampling (SBDS) (CVE-2022-21125)
+----------------------------------------------------
+After propagators may have moved data around the uncore and copied stale data
+into client core fill buffers, processors affected by MFBDS can leak data from
+the fill buffer. It is limited to the client (including Intel Xeon server E3)
+uncore implementation.
+
+Shared Buffers Data Read (SBDR) (CVE-2022-21123)
+------------------------------------------------
+It is similar to Shared Buffer Data Sampling (SBDS) except that the data is
+directly read into the architectural software-visible state. It is limited to
+the client (including Intel Xeon server E3) uncore implementation.
+
+Affected Processors
+===================
+Not all the CPUs are affected by all the variants. For instance, most
+processors for the server market (excluding Intel Xeon E3 processors) are
+impacted by only Device Register Partial Write (DRPW).
+
+Below is the list of affected Intel processors [#f1]_:
+
+   ===================  ============  =========
+   Common name          Family_Model  Steppings
+   ===================  ============  =========
+   HASWELL_X            06_3FH        2,4
+   SKYLAKE_L            06_4EH        3
+   BROADWELL_X          06_4FH        All
+   SKYLAKE_X            06_55H        3,4,6,7,11
+   BROADWELL_D          06_56H        3,4,5
+   SKYLAKE              06_5EH        3
+   ICELAKE_X            06_6AH        4,5,6
+   ICELAKE_D            06_6CH        1
+   ICELAKE_L            06_7EH        5
+   ATOM_TREMONT_D       06_86H        All
+   LAKEFIELD            06_8AH        1
+   KABYLAKE_L           06_8EH        9 to 12
+   ATOM_TREMONT         06_96H        1
+   ATOM_TREMONT_L       06_9CH        0
+   KABYLAKE             06_9EH        9 to 13
+   COMETLAKE            06_A5H        2,3,5
+   COMETLAKE_L          06_A6H        0,1
+   ROCKETLAKE           06_A7H        1
+   ===================  ============  =========
+
+If a CPU is in the affected processor list, but not affected by a variant, it
+is indicated by new bits in MSR IA32_ARCH_CAPABILITIES. As described in a later
+section, mitigation largely remains the same for all the variants, i.e. to
+clear the CPU fill buffers via VERW instruction.
+
+New bits in MSRs
+================
+Newer processors and microcode update on existing affected processors added new
+bits to IA32_ARCH_CAPABILITIES MSR. These bits can be used to enumerate
+specific variants of Processor MMIO Stale Data vulnerabilities and mitigation
+capability.
+
+MSR IA32_ARCH_CAPABILITIES
+--------------------------
+Bit 13 - SBDR_SSDP_NO - When set, processor is not affected by either the
+	 Shared Buffers Data Read (SBDR) vulnerability or the sideband stale
+	 data propagator (SSDP).
+Bit 14 - FBSDP_NO - When set, processor is not affected by the Fill Buffer
+	 Stale Data Propagator (FBSDP).
+Bit 15 - PSDP_NO - When set, processor is not affected by Primary Stale Data
+	 Propagator (PSDP).
+Bit 17 - FB_CLEAR - When set, VERW instruction will overwrite CPU fill buffer
+	 values as part of MD_CLEAR operations. Processors that do not
+	 enumerate MDS_NO (meaning they are affected by MDS) but that do
+	 enumerate support for both L1D_FLUSH and MD_CLEAR implicitly enumerate
+	 FB_CLEAR as part of their MD_CLEAR support.
+Bit 18 - FB_CLEAR_CTRL - Processor supports read and write to MSR
+	 IA32_MCU_OPT_CTRL[FB_CLEAR_DIS]. On such processors, the FB_CLEAR_DIS
+	 bit can be set to cause the VERW instruction to not perform the
+	 FB_CLEAR action. Not all processors that support FB_CLEAR will support
+	 FB_CLEAR_CTRL.
+
+MSR IA32_MCU_OPT_CTRL
+---------------------
+Bit 3 - FB_CLEAR_DIS - When set, VERW instruction does not perform the FB_CLEAR
+action. This may be useful to reduce the performance impact of FB_CLEAR in
+cases where system software deems it warranted (for example, when performance
+is more critical, or the untrusted software has no MMIO access). Note that
+FB_CLEAR_DIS has no impact on enumeration (for example, it does not change
+FB_CLEAR or MD_CLEAR enumeration) and it may not be supported on all processors
+that enumerate FB_CLEAR.
+
+Mitigation
+==========
+Like MDS, all variants of Processor MMIO Stale Data vulnerabilities  have the
+same mitigation strategy to force the CPU to clear the affected buffers before
+an attacker can extract the secrets.
+
+This is achieved by using the otherwise unused and obsolete VERW instruction in
+combination with a microcode update. The microcode clears the affected CPU
+buffers when the VERW instruction is executed.
+
+Kernel reuses the MDS function to invoke the buffer clearing:
+
+	mds_clear_cpu_buffers()
+
+On MDS affected CPUs, the kernel already invokes CPU buffer clear on
+kernel/userspace, hypervisor/guest and C-state (idle) transitions. No
+additional mitigation is needed on such CPUs.
+
+For CPUs not affected by MDS or TAA, mitigation is needed only for the attacker
+with MMIO capability. Therefore, VERW is not required for kernel/userspace. For
+virtualization case, VERW is only needed at VMENTER for a guest with MMIO
+capability.
+
+Mitigation points
+-----------------
+Return to user space
+^^^^^^^^^^^^^^^^^^^^
+Same mitigation as MDS when affected by MDS/TAA, otherwise no mitigation
+needed.
+
+C-State transition
+^^^^^^^^^^^^^^^^^^
+Control register writes by CPU during C-state transition can propagate data
+from fill buffer to uncore buffers. Execute VERW before C-state transition to
+clear CPU fill buffers.
+
+Guest entry point
+^^^^^^^^^^^^^^^^^
+Same mitigation as MDS when processor is also affected by MDS/TAA, otherwise
+execute VERW at VMENTER only for MMIO capable guests. On CPUs not affected by
+MDS/TAA, guest without MMIO access cannot extract secrets using Processor MMIO
+Stale Data vulnerabilities, so there is no need to execute VERW for such guests.
+
+Mitigation control on the kernel command line
+---------------------------------------------
+The kernel command line allows to control the Processor MMIO Stale Data
+mitigations at boot time with the option "mmio_stale_data=". The valid
+arguments for this option are:
+
+  ==========  =================================================================
+  full        If the CPU is vulnerable, enable mitigation; CPU buffer clearing
+              on exit to userspace and when entering a VM. Idle transitions are
+              protected as well. It does not automatically disable SMT.
+  full,nosmt  Same as full, with SMT disabled on vulnerable CPUs. This is the
+              complete mitigation.
+  off         Disables mitigation completely.
+  ==========  =================================================================
+
+If the CPU is affected and mmio_stale_data=off is not supplied on the kernel
+command line, then the kernel selects the appropriate mitigation.
+
+Mitigation status information
+-----------------------------
+The Linux kernel provides a sysfs interface to enumerate the current
+vulnerability status of the system: whether the system is vulnerable, and
+which mitigations are active. The relevant sysfs file is:
+
+	/sys/devices/system/cpu/vulnerabilities/mmio_stale_data
+
+The possible values in this file are:
+
+  .. list-table::
+
+     * - 'Not affected'
+       - The processor is not vulnerable
+     * - 'Vulnerable'
+       - The processor is vulnerable, but no mitigation enabled
+     * - 'Vulnerable: Clear CPU buffers attempted, no microcode'
+       - The processor is vulnerable, but microcode is not updated. The
+         mitigation is enabled on a best effort basis.
+     * - 'Mitigation: Clear CPU buffers'
+       - The processor is vulnerable and the CPU buffer clearing mitigation is
+         enabled.
+     * - 'Unknown: No mitigations'
+       - The processor vulnerability status is unknown because it is
+	 out of Servicing period. Mitigation is not attempted.
+
+Definitions:
+------------
+
+Servicing period: The process of providing functional and security updates to
+Intel processors or platforms, utilizing the Intel Platform Update (IPU)
+process or other similar mechanisms.
+
+End of Servicing Updates (ESU): ESU is the date at which Intel will no
+longer provide Servicing, such as through IPU or other similar update
+processes. ESU dates will typically be aligned to end of quarter.
+
+If the processor is vulnerable then the following information is appended to
+the above information:
+
+  ========================  ===========================================
+  'SMT vulnerable'          SMT is enabled
+  'SMT disabled'            SMT is disabled
+  'SMT Host state unknown'  Kernel runs in a VM, Host SMT state unknown
+  ========================  ===========================================
+
+References
+----------
+.. [#f1] Affected Processors
+   https://www.intel.com/content/www/us/en/developer/topic-technology/software-security-guidance/processors-affected-consolidated-product-cpu-model.html
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
@@ -0,0 +1,104 @@
+==================================
+Register File Data Sampling (RFDS)
+==================================
+
+Register File Data Sampling (RFDS) is a microarchitectural vulnerability that
+only affects Intel Atom parts(also branded as E-cores). RFDS may allow
+a malicious actor to infer data values previously used in floating point
+registers, vector registers, or integer registers. RFDS does not provide the
+ability to choose which data is inferred. CVE-2023-28746 is assigned to RFDS.
+
+Affected Processors
+===================
+Below is the list of affected Intel processors [#f1]_:
+
+   ===================  ============
+   Common name          Family_Model
+   ===================  ============
+   ATOM_GOLDMONT           06_5CH
+   ATOM_GOLDMONT_D         06_5FH
+   ATOM_GOLDMONT_PLUS      06_7AH
+   ATOM_TREMONT_D          06_86H
+   ATOM_TREMONT            06_96H
+   ALDERLAKE               06_97H
+   ALDERLAKE_L             06_9AH
+   ATOM_TREMONT_L          06_9CH
+   RAPTORLAKE              06_B7H
+   RAPTORLAKE_P            06_BAH
+   ALDERLAKE_N             06_BEH
+   RAPTORLAKE_S            06_BFH
+   ===================  ============
+
+As an exception to this table, Intel Xeon E family parts ALDERLAKE(06_97H) and
+RAPTORLAKE(06_B7H) codenamed Catlow are not affected. They are reported as
+vulnerable in Linux because they share the same family/model with an affected
+part. Unlike their affected counterparts, they do not enumerate RFDS_CLEAR or
+CPUID.HYBRID. This information could be used to distinguish between the
+affected and unaffected parts, but it is deemed not worth adding complexity as
+the reporting is fixed automatically when these parts enumerate RFDS_NO.
+
+Mitigation
+==========
+Intel released a microcode update that enables software to clear sensitive
+information using the VERW instruction. Like MDS, RFDS deploys the same
+mitigation strategy to force the CPU to clear the affected buffers before an
+attacker can extract the secrets. This is achieved by using the otherwise
+unused and obsolete VERW instruction in combination with a microcode update.
+The microcode clears the affected CPU buffers when the VERW instruction is
+executed.
+
+Mitigation points
+-----------------
+VERW is executed by the kernel before returning to user space, and by KVM
+before VMentry. None of the affected cores support SMT, so VERW is not required
+at C-state transitions.
+
+New bits in IA32_ARCH_CAPABILITIES
+----------------------------------
+Newer processors and microcode update on existing affected processors added new
+bits to IA32_ARCH_CAPABILITIES MSR. These bits can be used to enumerate
+vulnerability and mitigation capability:
+
+- Bit 27 - RFDS_NO - When set, processor is not affected by RFDS.
+- Bit 28 - RFDS_CLEAR - When set, processor is affected by RFDS, and has the
+  microcode that clears the affected buffers on VERW execution.
+
+Mitigation control on the kernel command line
+---------------------------------------------
+The kernel command line allows to control RFDS mitigation at boot time with the
+parameter "reg_file_data_sampling=". The valid arguments are:
+
+  ==========  =================================================================
+  on          If the CPU is vulnerable, enable mitigation; CPU buffer clearing
+              on exit to userspace and before entering a VM.
+  off         Disables mitigation.
+  ==========  =================================================================
+
+Mitigation default is selected by CONFIG_MITIGATION_RFDS.
+
+Mitigation status information
+-----------------------------
+The Linux kernel provides a sysfs interface to enumerate the current
+vulnerability status of the system: whether the system is vulnerable, and
+which mitigations are active. The relevant sysfs file is:
+
+	/sys/devices/system/cpu/vulnerabilities/reg_file_data_sampling
+
+The possible values in this file are:
+
+  .. list-table::
+
+     * - 'Not affected'
+       - The processor is not vulnerable
+     * - 'Vulnerable'
+       - The processor is vulnerable, but no mitigation enabled
+     * - 'Vulnerable: No microcode'
+       - The processor is vulnerable but microcode is not updated.
+     * - 'Mitigation: Clear Register File'
+       - The processor is vulnerable and the CPU buffer clearing mitigation is
+	 enabled.
+
+References
+----------
+.. [#f1] Affected Processors
+   https://www.intel.com/content/www/us/en/developer/topic-technology/software-security-guidance/processors-affected-consolidated-product-cpu-model.html
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/spectre.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/spectre.rst
@@ -60,8 +60,8 @@
 Spectre variant 1 attacks take advantage of speculative execution of
 conditional branches, while Spectre variant 2 attacks use speculative
 execution of indirect branches to leak privileged memory.
-See :ref:`[1] <spec_ref1>` :ref:`[5] <spec_ref5>` :ref:`[7] <spec_ref7>`
-:ref:`[10] <spec_ref10>` :ref:`[11] <spec_ref11>`.
+See :ref:`[1] <spec_ref1>` :ref:`[5] <spec_ref5>` :ref:`[6] <spec_ref6>`
+:ref:`[7] <spec_ref7>` :ref:`[10] <spec_ref10>` :ref:`[11] <spec_ref11>`.
 
 Spectre variant 1 (Bounds Check Bypass)
 ---------------------------------------
@@ -131,6 +131,18 @@
 speculative execution's side effects left in level 1 cache to infer the
 victim's data.
 
+Yet another variant 2 attack vector is for the attacker to poison the
+Branch History Buffer (BHB) to speculatively steer an indirect branch
+to a specific Branch Target Buffer (BTB) entry, even if the entry isn't
+associated with the source address of the indirect branch. Specifically,
+the BHB might be shared across privilege levels even in the presence of
+Enhanced IBRS.
+
+Previously the only known real-world BHB attack vector was via unprivileged
+eBPF. Further research has found attacks that don't require unprivileged eBPF.
+For a full mitigation against BHB attacks it is recommended to set BHI_DIS_S or
+use the BHB clearing sequence.
+
 Attack scenarios
 ----------------
 
@@ -364,13 +376,15 @@
 
   - Kernel status:
 
-  ====================================  =================================
-  'Not affected'                        The processor is not vulnerable
-  'Vulnerable'                          Vulnerable, no mitigation
-  'Mitigation: Full generic retpoline'  Software-focused mitigation
-  'Mitigation: Full AMD retpoline'      AMD-specific software mitigation
-  'Mitigation: Enhanced IBRS'           Hardware-focused mitigation
-  ====================================  =================================
+  ========================================  =================================
+  'Not affected'                            The processor is not vulnerable
+  'Mitigation: None'                        Vulnerable, no mitigation
+  'Mitigation: Retpolines'                  Use Retpoline thunks
+  'Mitigation: LFENCE'                      Use LFENCE instructions
+  'Mitigation: Enhanced IBRS'               Hardware-focused mitigation
+  'Mitigation: Enhanced IBRS + Retpolines'  Hardware-focused + Retpolines
+  'Mitigation: Enhanced IBRS + LFENCE'      Hardware-focused + LFENCE
+  ========================================  =================================
 
   - Firmware status: Show if Indirect Branch Restricted Speculation (IBRS) is
     used to protect against Spectre variant 2 attacks when calling firmware (x86 only).
@@ -407,6 +421,31 @@
   'RSB filling'   Protection of RSB on context switch enabled
   =============   ===========================================
 
+  - EIBRS Post-barrier Return Stack Buffer (PBRSB) protection status:
+
+  ===========================  =======================================================
+  'PBRSB-eIBRS: SW sequence'   CPU is affected and protection of RSB on VMEXIT enabled
+  'PBRSB-eIBRS: Vulnerable'    CPU is vulnerable
+  'PBRSB-eIBRS: Not affected'  CPU is not affected by PBRSB
+  ===========================  =======================================================
+
+  - Branch History Injection (BHI) protection status:
+
+.. list-table::
+
+ * - BHI: Not affected
+   - System is not affected
+ * - BHI: Retpoline
+   - System is protected by retpoline
+ * - BHI: BHI_DIS_S
+   - System is protected by BHI_DIS_S
+ * - BHI: SW loop, KVM SW loop
+   - System is protected by software clearing sequence
+ * - BHI: Vulnerable
+   - System is vulnerable to BHI
+ * - BHI: Vulnerable, KVM: SW loop
+   - System is vulnerable; KVM is protected by software clearing sequence
+
 Full mitigation might require a microcode update from the CPU
 vendor. When the necessary microcode is not available, the kernel will
 report vulnerability.
@@ -456,8 +495,23 @@
    On Intel Skylake-era systems the mitigation covers most, but not all,
    cases. See :ref:`[3] <spec_ref3>` for more details.
 
-   On CPUs with hardware mitigation for Spectre variant 2 (e.g. Enhanced
-   IBRS on x86), retpoline is automatically disabled at run time.
+   On CPUs with hardware mitigation for Spectre variant 2 (e.g. IBRS
+   or enhanced IBRS on x86), retpoline is automatically disabled at run time.
+
+   Systems which support enhanced IBRS (eIBRS) enable IBRS protection once at
+   boot, by setting the IBRS bit, and they're automatically protected against
+   some Spectre v2 variant attacks. The BHB can still influence the choice of
+   indirect branch predictor entry, and although branch predictor entries are
+   isolated between modes when eIBRS is enabled, the BHB itself is not isolated
+   between modes. Systems which support BHI_DIS_S will set it to protect against
+   BHI attacks.
+
+   On Intel's enhanced IBRS systems, this includes cross-thread branch target
+   injections on SMT systems (STIBP). In other words, Intel eIBRS enables
+   STIBP, too.
+
+   AMD Automatic IBRS does not protect userspace, and Legacy IBRS systems clear
+   the IBRS bit on exit to userspace, therefore both explicitly enable STIBP.
 
    The retpoline mitigation is turned on by default on vulnerable
    CPUs. It can be forced on or off by the administrator
@@ -468,7 +522,7 @@
    before invoking any firmware code to prevent Spectre variant 2 exploits
    using the firmware.
 
-   Using kernel address space randomization (CONFIG_RANDOMIZE_SLAB=y
+   Using kernel address space randomization (CONFIG_RANDOMIZE_BASE=y
    and CONFIG_SLAB_FREELIST_RANDOM=y in the kernel configuration) makes
    attacks on the kernel generally more difficult.
 
@@ -481,9 +535,12 @@
    For Spectre variant 2 mitigation, individual user programs
    can be compiled with return trampolines for indirect branches.
    This protects them from consuming poisoned entries in the branch
-   target buffer left by malicious software.  Alternatively, the
-   programs can disable their indirect branch speculation via prctl()
-   (See :ref:`Documentation/userspace-api/spec_ctrl.rst <set_spec_ctrl>`).
+   target buffer left by malicious software.
+
+   On legacy IBRS systems, at return to userspace, implicit STIBP is disabled
+   because the kernel clears the IBRS bit. In this case, the userspace programs
+   can disable indirect branch speculation via prctl() (See
+   :ref:`Documentation/userspace-api/spec_ctrl.rst <set_spec_ctrl>`).
    On x86, this will turn on STIBP to guard against attacks from the
    sibling thread when the user program is running, and use IBPB to
    flush the branch target buffer when switching to/from the program.
@@ -584,12 +641,14 @@
 
 		Specific mitigations can also be selected manually:
 
-		retpoline
-					replace indirect branches
-		retpoline,generic
-					google's original retpoline
-		retpoline,amd
-					AMD-specific minimal thunk
+                retpoline               auto pick between generic,lfence
+                retpoline,generic       Retpolines
+                retpoline,lfence        LFENCE; indirect branch
+                retpoline,amd           alias for retpoline,lfence
+                eibrs                   Enhanced/Auto IBRS
+                eibrs,retpoline         Enhanced/Auto IBRS + Retpolines
+                eibrs,lfence            Enhanced/Auto IBRS + LFENCE
+                ibrs                    use IBRS to protect kernel
 
 		Not specifying this option is equivalent to
 		spectre_v2=auto.
@@ -649,6 +708,20 @@
 		spectre_v2=off. Spectre variant 1 mitigations
 		cannot be disabled.
 
+	spectre_bhi=
+
+		[X86] Control mitigation of Branch History Injection
+		(BHI) vulnerability.  This setting affects the deployment
+		of the HW BHI control and the SW BHB clearing sequence.
+
+		on
+			(default) Enable the HW or SW mitigation as
+			needed.
+		off
+			Disable the mitigation.
+
+For spectre_v2_user see Documentation/admin-guide/kernel-parameters.txt
+
 Mitigation selection guide
 --------------------------
 
@@ -730,7 +803,7 @@
 
 .. _spec_ref6:
 
-[6] `Software techniques for managing speculation on AMD processors <https://developer.amd.com/wp-content/resources/90343-B_SoftwareTechniquesforManagingSpeculation_WP_7-18Update_FNL.pdf>`_.
+[6] `Software techniques for managing speculation on AMD processors <https://developer.amd.com/wp-content/resources/Managing-Speculation-on-AMD-Processors.pdf>`_.
 
 ARM white papers:
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/hw-vuln/srso.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/hw-vuln/srso.rst
@@ -0,0 +1,133 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Speculative Return Stack Overflow (SRSO)
+========================================
+
+This is a mitigation for the speculative return stack overflow (SRSO)
+vulnerability found on AMD processors. The mechanism is by now the well
+known scenario of poisoning CPU functional units - the Branch Target
+Buffer (BTB) and Return Address Predictor (RAP) in this case - and then
+tricking the elevated privilege domain (the kernel) into leaking
+sensitive data.
+
+AMD CPUs predict RET instructions using a Return Address Predictor (aka
+Return Address Stack/Return Stack Buffer). In some cases, a non-architectural
+CALL instruction (i.e., an instruction predicted to be a CALL but is
+not actually a CALL) can create an entry in the RAP which may be used
+to predict the target of a subsequent RET instruction.
+
+The specific circumstances that lead to this varies by microarchitecture
+but the concern is that an attacker can mis-train the CPU BTB to predict
+non-architectural CALL instructions in kernel space and use this to
+control the speculative target of a subsequent kernel RET, potentially
+leading to information disclosure via a speculative side-channel.
+
+The issue is tracked under CVE-2023-20569.
+
+Affected processors
+-------------------
+
+AMD Zen, generations 1-4. That is, all families 0x17 and 0x19. Older
+processors have not been investigated.
+
+System information and options
+------------------------------
+
+First of all, it is required that the latest microcode be loaded for
+mitigations to be effective.
+
+The sysfs file showing SRSO mitigation status is:
+
+  /sys/devices/system/cpu/vulnerabilities/spec_rstack_overflow
+
+The possible values in this file are:
+
+ - 'Not affected'               The processor is not vulnerable
+
+ - 'Vulnerable: no microcode'   The processor is vulnerable, no
+                                microcode extending IBPB functionality
+                                to address the vulnerability has been
+                                applied.
+
+ - 'Mitigation: microcode'      Extended IBPB functionality microcode
+                                patch has been applied. It does not
+                                address User->Kernel and Guest->Host
+                                transitions protection but it does
+                                address User->User and VM->VM attack
+                                vectors.
+
+                                (spec_rstack_overflow=microcode)
+
+ - 'Mitigation: safe RET'       Software-only mitigation. It complements
+                                the extended IBPB microcode patch
+                                functionality by addressing User->Kernel
+                                and Guest->Host transitions protection.
+
+                                Selected by default or by
+                                spec_rstack_overflow=safe-ret
+
+ - 'Mitigation: IBPB'           Similar protection as "safe RET" above
+                                but employs an IBPB barrier on privilege
+                                domain crossings (User->Kernel,
+                                Guest->Host).
+
+                                (spec_rstack_overflow=ibpb)
+
+ - 'Mitigation: IBPB on VMEXIT' Mitigation addressing the cloud provider
+                                scenario - the Guest->Host transitions
+                                only.
+
+                                (spec_rstack_overflow=ibpb-vmexit)
+
+In order to exploit vulnerability, an attacker needs to:
+
+ - gain local access on the machine
+
+ - break kASLR
+
+ - find gadgets in the running kernel in order to use them in the exploit
+
+ - potentially create and pin an additional workload on the sibling
+   thread, depending on the microarchitecture (not necessary on fam 0x19)
+
+ - run the exploit
+
+Considering the performance implications of each mitigation type, the
+default one is 'Mitigation: safe RET' which should take care of most
+attack vectors, including the local User->Kernel one.
+
+As always, the user is advised to keep her/his system up-to-date by
+applying software updates regularly.
+
+The default setting will be reevaluated when needed and especially when
+new attack vectors appear.
+
+As one can surmise, 'Mitigation: safe RET' does come at the cost of some
+performance depending on the workload. If one trusts her/his userspace
+and does not want to suffer the performance impact, one can always
+disable the mitigation with spec_rstack_overflow=off.
+
+Similarly, 'Mitigation: IBPB' is another full mitigation type employing
+an indrect branch prediction barrier after having applied the required
+microcode patch for one's system. This mitigation comes also at
+a performance cost.
+
+Mitigation: safe RET
+--------------------
+
+The mitigation works by ensuring all RET instructions speculate to
+a controlled location, similar to how speculation is controlled in the
+retpoline sequence.  To accomplish this, the __x86_return_thunk forces
+the CPU to mispredict every function return using a 'safe return'
+sequence.
+
+To ensure the safety of this mitigation, the kernel must ensure that the
+safe return sequence is itself free from attacker interference.  In Zen3
+and Zen4, this is accomplished by creating a BTB alias between the
+untraining function srso_alias_untrain_ret() and the safe return
+function srso_alias_safe_ret() which results in evicting a potentially
+poisoned BTB entry and using that safe one for all function returns.
+
+In older Zen1 and Zen2, this is accomplished using a reinterpretation
+technique similar to Retbleed one: srso_untrain_ret() and
+srso_safe_ret().
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/index.rst
@@ -82,6 +82,7 @@
    edid
    efi-stub
    ext4
+   filesystem-monitoring
    nfs/index
    gpio/index
    highuid
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/kdump/gdbmacros.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/kdump/gdbmacros.txt
@@ -312,10 +312,10 @@
 			set var $prev_flags = $info->flags
 		end
 
-		set var $id = ($id + 1) & $id_mask
 		if ($id == $end_id)
 			loop_break
 		end
+		set var $id = ($id + 1) & $id_mask
 	end
 end
 document dmesg
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/kernel-parameters.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/kernel-parameters.txt
@@ -600,12 +600,6 @@
 			loops can be debugged more effectively on production
 			systems.
 
-	clocksource.max_cswd_read_retries= [KNL]
-			Number of clocksource_watchdog() retries due to
-			external delays before the clock will be marked
-			unstable.  Defaults to three retries, that is,
-			four attempts to read the clock under test.
-
 	clocksource.verify_n_cpus= [KNL]
 			Limit the number of CPUs checked for clocksources
 			marked with CLOCK_SOURCE_VERIFY_PERCPU that
@@ -750,6 +744,10 @@
 			0: default value, disable debugging
 			1: enable debugging at boot time
 
+	cpufreq_driver= [X86] Allow only the named cpu frequency scaling driver
+			to register. Example: cpufreq_driver=powernow-k8
+			Format: { none | STRING }
+
 	cpuidle.off=1	[CPU_IDLE]
 			disable the cpuidle sub-system
 
@@ -780,7 +778,7 @@
 			memory region [offset, offset + size] for that kernel
 			image. If '@offset' is omitted, then a suitable offset
 			is selected automatically.
-			[KNL, X86-64] Select a region under 4G first, and
+			[KNL, X86-64, ARM64] Select a region under 4G first, and
 			fall back to reserve region above 4G when '@offset'
 			hasn't been specified.
 			See Documentation/admin-guide/kdump/kdump.rst for further details.
@@ -793,22 +791,25 @@
 			Documentation/admin-guide/kdump/kdump.rst for an example.
 
 	crashkernel=size[KMG],high
-			[KNL, X86-64] range could be above 4G. Allow kernel
+			[KNL, X86-64, ARM64] range could be above 4G. Allow kernel
 			to allocate physical memory region from top, so could
 			be above 4G if system have more than 4G ram installed.
 			Otherwise memory region will be allocated below 4G, if
 			available.
 			It will be ignored if crashkernel=X is specified.
 	crashkernel=size[KMG],low
-			[KNL, X86-64] range under 4G. When crashkernel=X,high
+			[KNL, X86-64, ARM64] range under 4G. When crashkernel=X,high
 			is passed, kernel could allocate physical memory region
 			above 4G, that cause second kernel crash on system
 			that require some amount of low memory, e.g. swiotlb
 			requires at least 64M+32K low memory, also enough extra
 			low memory is needed to make sure DMA buffers for 32-bit
-			devices won't run out. Kernel would try to allocate at
-			at least 256M below 4G automatically.
-			This one let user to specify own low range under 4G
+			devices won't run out. Kernel would try to allocate
+			default	size of memory below 4G automatically. The default
+			size is	platform dependent.
+			  --> x86: max(swiotlb_size_or_default() + 8MiB, 256MiB)
+			  --> arm64: 128MiB
+			This one lets the user specify own low range under 4G
 			for second kernel instead.
 			0: to disable low allocation.
 			It will be ignored when crashkernel=X,high is not used
@@ -916,10 +917,6 @@
 
 	debugpat	[X86] Enable PAT debugging
 
-	decnet.addr=	[HW,NET]
-			Format: <area>[,<node>]
-			See also Documentation/networking/decnet.rst.
-
 	default_hugepagesz=
 			[HW] The size of the default HugeTLB page. This is
 			the size represented by the legacy /proc/ hugepages
@@ -1041,6 +1038,26 @@
 			The filter can be disabled or changed to another
 			driver later using sysfs.
 
+	reg_file_data_sampling=
+			[X86] Controls mitigation for Register File Data
+			Sampling (RFDS) vulnerability. RFDS is a CPU
+			vulnerability which may allow userspace to infer
+			kernel data values previously stored in floating point
+			registers, vector registers, or integer registers.
+			RFDS only affects Intel Atom processors.
+
+			on:	Turns ON the mitigation.
+			off:	Turns OFF the mitigation.
+
+			This parameter overrides the compile time default set
+			by CONFIG_MITIGATION_RFDS. Mitigation cannot be
+			disabled when other VERW based mitigations (like MDS)
+			are enabled. In order to disable RFDS mitigation all
+			VERW based mitigations need to be disabled.
+
+			For details see:
+			Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
+
 	driver_async_probe=  [KNL]
 			List of driver names to be probed asynchronously.
 			Format: <driver_name1>,<driver_name2>...
@@ -1088,8 +1105,12 @@
 	nopku		[X86] Disable Memory Protection Keys CPU feature found
 			in some Intel CPUs.
 
-	<module>.async_probe [KNL]
-			Enable asynchronous probe on this module.
+	<module>.async_probe[=<bool>] [KNL]
+			If no <bool> value is specified or if the value
+			specified is not a valid <bool>, enable asynchronous
+			probe on this module.  Otherwise, enable/disable
+			asynchronous probe on this module as indicated by the
+			<bool> value. See also: module.async_probe
 
 	early_ioremap_debug [KNL]
 			Enable debug messages in early_ioremap support. This
@@ -1505,6 +1526,26 @@
 			Format: off | on
 			default: on
 
+	gather_data_sampling=
+			[X86,INTEL] Control the Gather Data Sampling (GDS)
+			mitigation.
+
+			Gather Data Sampling is a hardware vulnerability which
+			allows unprivileged speculative access to data which was
+			previously stored in vector registers.
+
+			This issue is mitigated by default in updated microcode.
+			The mitigation may have a performance impact but can be
+			disabled. On systems without the microcode mitigation
+			disabling AVX serves as a mitigation.
+
+			force:	Disable AVX to mitigate systems without
+				microcode mitigation. No effect if the microcode
+				mitigation is present. Known to cause crashes in
+				userspace with buggy AVX enumeration.
+
+			off:	Disable GDS mitigation.
+
 	gcov_persist=	[GCOV] When non-zero (default), profiling data for
 			kernel modules is saved and remains accessible via
 			debugfs, even when the module is unloaded/reloaded.
@@ -1690,6 +1731,8 @@
 			architectures force reset to be always executed
 	i8042.unlock	[HW] Unlock (ignore) the keylock
 	i8042.kbdreset	[HW] Reset device connected to KBD port
+	i8042.probe_defer
+			[HW] Allow deferred probing upon i8042 probe errors
 
 	i810=		[HW,DRM]
 
@@ -2198,24 +2241,57 @@
 
 	ivrs_ioapic	[HW,X86-64]
 			Provide an override to the IOAPIC-ID<->DEVICE-ID
-			mapping provided in the IVRS ACPI table. For
-			example, to map IOAPIC-ID decimal 10 to
-			PCI device 00:14.0 write the parameter as:
+			mapping provided in the IVRS ACPI table.
+			By default, PCI segment is 0, and can be omitted.
+
+			For example, to map IOAPIC-ID decimal 10 to
+			PCI segment 0x1 and PCI device 00:14.0,
+			write the parameter as:
+				ivrs_ioapic=10@0001:00:14.0
+
+			Deprecated formats:
+			* To map IOAPIC-ID decimal 10 to PCI device 00:14.0
+			  write the parameter as:
 				ivrs_ioapic[10]=00:14.0
+			* To map IOAPIC-ID decimal 10 to PCI segment 0x1 and
+			  PCI device 00:14.0 write the parameter as:
+				ivrs_ioapic[10]=0001:00:14.0
 
 	ivrs_hpet	[HW,X86-64]
 			Provide an override to the HPET-ID<->DEVICE-ID
-			mapping provided in the IVRS ACPI table. For
-			example, to map HPET-ID decimal 0 to
-			PCI device 00:14.0 write the parameter as:
+			mapping provided in the IVRS ACPI table.
+			By default, PCI segment is 0, and can be omitted.
+
+			For example, to map HPET-ID decimal 10 to
+			PCI segment 0x1 and PCI device 00:14.0,
+			write the parameter as:
+				ivrs_hpet=10@0001:00:14.0
+
+			Deprecated formats:
+			* To map HPET-ID decimal 0 to PCI device 00:14.0
+			  write the parameter as:
 				ivrs_hpet[0]=00:14.0
+			* To map HPET-ID decimal 10 to PCI segment 0x1 and
+			  PCI device 00:14.0 write the parameter as:
+				ivrs_ioapic[10]=0001:00:14.0
 
 	ivrs_acpihid	[HW,X86-64]
 			Provide an override to the ACPI-HID:UID<->DEVICE-ID
-			mapping provided in the IVRS ACPI table. For
-			example, to map UART-HID:UID AMD0020:0 to
-			PCI device 00:14.5 write the parameter as:
+			mapping provided in the IVRS ACPI table.
+			By default, PCI segment is 0, and can be omitted.
+
+			For example, to map UART-HID:UID AMD0020:0 to
+			PCI segment 0x1 and PCI device ID 00:14.5,
+			write the parameter as:
+				ivrs_acpihid=AMD0020:0@0001:00:14.5
+
+			Deprecated formats:
+			* To map UART-HID:UID AMD0020:0 to PCI segment is 0,
+			  PCI device ID 00:14.5, write the parameter as:
 				ivrs_acpihid[00:14.5]=AMD0020:0
+			* To map UART-HID:UID AMD0020:0 to PCI segment 0x1 and
+			  PCI device ID 00:14.5, write the parameter as:
+				ivrs_acpihid[0001:00:14.5]=AMD0020:0
 
 	js=		[HW,JOY] Analog joystick
 			See Documentation/input/joydev/joystick.rst.
@@ -2403,8 +2479,12 @@
 			Default is 1 (enabled)
 
 	kvm-intel.emulate_invalid_guest_state=
-			[KVM,Intel] Enable emulation of invalid guest states
-			Default is 0 (disabled)
+			[KVM,Intel] Disable emulation of invalid guest state.
+			Ignored if kvm-intel.enable_unrestricted_guest=1, as
+			guest state is never invalid for unrestricted guests.
+			This param doesn't apply to nested guests (L2), as KVM
+			never emulates invalid L2 guest state.
+			Default is 1 (enabled)
 
 	kvm-intel.flexpriority=
 			[KVM,Intel] Disable FlexPriority feature (TPR shadow).
@@ -2999,20 +3079,27 @@
 				Disable all optional CPU mitigations.  This
 				improves system performance, but it may also
 				expose users to several CPU vulnerabilities.
-				Equivalent to: nopti [X86,PPC]
-					       kpti=0 [ARM64]
-					       nospectre_v1 [X86,PPC]
+				Equivalent to: if nokaslr then kpti=0 [ARM64]
+					       gather_data_sampling=off [X86]
+					       kvm.nx_huge_pages=off [X86]
+					       l1tf=off [X86]
+					       mds=off [X86]
+					       mmio_stale_data=off [X86]
+					       no_entry_flush [PPC]
+					       no_uaccess_flush [PPC]
 					       nobp=0 [S390]
+					       nopti [X86,PPC]
+					       nospectre_bhb [ARM64]
+					       nospectre_v1 [X86,PPC]
 					       nospectre_v2 [X86,PPC,S390,ARM64]
-					       spectre_v2_user=off [X86]
+					       reg_file_data_sampling=off [X86]
+					       retbleed=off [X86]
 					       spec_store_bypass_disable=off [X86,PPC]
+					       spectre_bhi=off [X86]
+					       spectre_v2_user=off [X86]
+					       srbds=off [X86,INTEL]
 					       ssbd=force-off [ARM64]
-					       l1tf=off [X86]
-					       mds=off [X86]
 					       tsx_async_abort=off [X86]
-					       kvm.nx_huge_pages=off [X86]
-					       no_entry_flush [PPC]
-					       no_uaccess_flush [PPC]
 
 				Exceptions:
 					       This does not have any effect on
@@ -3034,6 +3121,8 @@
 				Equivalent to: l1tf=flush,nosmt [X86]
 					       mds=full,nosmt [X86]
 					       tsx_async_abort=full,nosmt [X86]
+					       mmio_stale_data=full,nosmt [X86]
+					       retbleed=auto,nosmt [X86]
 
 	mminit_loglevel=
 			[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
@@ -3043,6 +3132,49 @@
 			log everything. Information is printed at KERN_DEBUG
 			so loglevel=8 may also need to be specified.
 
+	mmio_stale_data=
+			[X86,INTEL] Control mitigation for the Processor
+			MMIO Stale Data vulnerabilities.
+
+			Processor MMIO Stale Data is a class of
+			vulnerabilities that may expose data after an MMIO
+			operation. Exposed data could originate or end in
+			the same CPU buffers as affected by MDS and TAA.
+			Therefore, similar to MDS and TAA, the mitigation
+			is to clear the affected CPU buffers.
+
+			This parameter controls the mitigation. The
+			options are:
+
+			full       - Enable mitigation on vulnerable CPUs
+
+			full,nosmt - Enable mitigation and disable SMT on
+				     vulnerable CPUs.
+
+			off        - Unconditionally disable mitigation
+
+			On MDS or TAA affected machines,
+			mmio_stale_data=off can be prevented by an active
+			MDS or TAA mitigation as these vulnerabilities are
+			mitigated with the same mechanism so in order to
+			disable this mitigation, you need to specify
+			mds=off and tsx_async_abort=off too.
+
+			Not specifying this option is equivalent to
+			mmio_stale_data=full.
+
+			For details see:
+			Documentation/admin-guide/hw-vuln/processor_mmio_stale_data.rst
+
+	module.async_probe=<bool>
+			[KNL] When set to true, modules will use async probing
+			by default. To enable/disable async probing for a
+			specific module, use the module specific control that
+			is documented under <module>.async_probe. When both
+			module.async_probe and <module>.async_probe are
+			specified, <module>.async_probe takes precedence for
+			the specific module.
+
 	module.sig_enforce
 			[KNL] When CONFIG_MODULE_SIG is set, this means that
 			modules without (valid) signatures will fail to load.
@@ -3328,9 +3460,6 @@
 
 	noautogroup	Disable scheduler automatic task group creation.
 
-	nobats		[PPC] Do not use BATs for mapping kernel lowmem
-			on "Classic" PPC cores.
-
 	nocache		[ARM]
 
 	noclflush	[BUGS=X86] Don't use the CLFLUSH instruction
@@ -3446,8 +3575,7 @@
 			difficult since unequal pointers can no longer be
 			compared.  However, if this command-line option is
 			specified, then all normal pointers will have their true
-			value printed.  Pointers printed via %pK may still be
-			hashed.  This option should only be specified when
+			value printed. This option should only be specified when
 			debugging the kernel.  Please do not use on production
 			kernels.
 
@@ -3507,9 +3635,6 @@
 
 	nolapic_timer	[X86-32,APIC] Do not use the local APIC timer.
 
-	noltlbs		[PPC] Do not use large page/tlb entries for kernel
-			lowmem mapping on PPC40x and PPC8xx
-
 	nomca		[IA-64] Disable machine check abort handling
 
 	nomce		[X86-32] Disable Machine Check Exception
@@ -3892,6 +4017,12 @@
 		nomsi		[MSI] If the PCI_MSI kernel config parameter is
 				enabled, this kernel boot option can be used to
 				disable the use of MSI interrupts system-wide.
+		clearmsi	[X86] Clears MSI/MSI-X enable bits early in boot
+				time in order to avoid issues like adapters
+				screaming irqs and preventing boot progress.
+				Also, it enforces the PCI Local Bus spec
+				rule that those bits should be 0 in system reset
+				events (useful for kexec/kdump cases).
 		noioapicquirk	[APIC] Disable all boot interrupt quirks.
 				Safety option to keep boot IRQs enabled. This
 				should never be necessary.
@@ -3949,6 +4080,15 @@
 				please report a bug.
 		nocrs		[X86] Ignore PCI host bridge windows from ACPI.
 				If you need to use this, please report a bug.
+		use_e820	[X86] Use E820 reservations to exclude parts of
+				PCI host bridge windows. This is a workaround
+				for BIOS defects in host bridge _CRS methods.
+				If you need to use this, please report a bug to
+				<linux-pci@vger.kernel.org>.
+		no_e820		[X86] Ignore E820 reservations for PCI host
+				bridge windows. This is the default on modern
+				hardware. If you need to use this, please report
+				a bug to <linux-pci@vger.kernel.org>.
 		routeirq	Do IRQ routing for all PCI devices.
 				This is normally done in pci_enable_device(),
 				so this option is a temporary workaround
@@ -4217,6 +4357,16 @@
 	printk.time=	Show timing data prefixed to each printk message line
 			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
 
+	proc_mem.force_override= [KNL]
+			Format: {always | ptrace | never}
+			Traditionally /proc/pid/mem allows memory permissions to be
+			overridden without restrictions. This option may be set to
+			restrict that. Can be one of:
+			- 'always': traditional behavior always allows mem overrides.
+			- 'ptrace': only allow mem overrides for active ptracers.
+			- 'never':  never allow mem overrides.
+			If not specified, default is the CONFIG_PROC_MEM_* choice.
+
 	processor.max_cstate=	[HW,ACPI]
 			Limit processor to maximum C-state
 			max_cstate=9 overrides any DMI blacklist limit.
@@ -4227,11 +4377,9 @@
 
 	profile=	[KNL] Enable kernel profiling via /proc/profile
 			Format: [<profiletype>,]<number>
-			Param: <profiletype>: "schedule", "sleep", or "kvm"
+			Param: <profiletype>: "schedule" or "kvm"
 				[defaults to kernel profiling]
 			Param: "schedule" - profile schedule points.
-			Param: "sleep" - profile D-state sleeping (millisecs).
-				Requires CONFIG_SCHEDSTATS
 			Param: "kvm" - profile VM exits.
 			Param: <number> - step/bucket size as a power of 2 for
 				statistical time based profiling.
@@ -4302,6 +4450,12 @@
 			fully seed the kernel's CRNG. Default is controlled
 			by CONFIG_RANDOM_TRUST_CPU.
 
+	random.trust_bootloader={on,off}
+			[KNL] Enable or disable trusting the use of a
+			seed passed by the bootloader (if available) to
+			fully seed the kernel's CRNG. Default is controlled
+			by CONFIG_RANDOM_TRUST_BOOTLOADER.
+
 	randomize_kstack_offset=
 			[KNL] Enable or disable kernel stack offset
 			randomization, which provides roughly 5 bits of
@@ -4921,6 +5075,43 @@
 
 	retain_initrd	[RAM] Keep initrd memory after extraction
 
+	retbleed=	[X86] Control mitigation of RETBleed (Arbitrary
+			Speculative Code Execution with Return Instructions)
+			vulnerability.
+
+			AMD-based UNRET and IBPB mitigations alone do not stop
+			sibling threads from influencing the predictions of other
+			sibling threads. For that reason, STIBP is used on pro-
+			cessors that support it, and mitigate SMT on processors
+			that don't.
+
+			off          - no mitigation
+			auto         - automatically select a migitation
+			auto,nosmt   - automatically select a mitigation,
+				       disabling SMT if necessary for
+				       the full mitigation (only on Zen1
+				       and older without STIBP).
+			ibpb         - On AMD, mitigate short speculation
+				       windows on basic block boundaries too.
+				       Safe, highest perf impact. It also
+				       enables STIBP if present. Not suitable
+				       on Intel.
+			ibpb,nosmt   - Like "ibpb" above but will disable SMT
+				       when STIBP is not available. This is
+				       the alternative for systems which do not
+				       have STIBP.
+			unret        - Force enable untrained return thunks,
+				       only effective on AMD f15h-f17h based
+				       systems.
+			unret,nosmt  - Like unret, but will disable SMT when STIBP
+				       is not available. This is the alternative for
+				       systems which do not have STIBP.
+
+			Selecting 'auto' will choose a mitigation method at run
+			time according to the CPU.
+
+			Not specifying this option is equivalent to retbleed=auto.
+
 	rfkill.default_state=
 		0	"airplane mode".  All wifi, bluetooth, wimax, gps, fm,
 			etc. communication is blocked by default.
@@ -5234,6 +5425,15 @@
 	sonypi.*=	[HW] Sony Programmable I/O Control Device driver
 			See Documentation/admin-guide/laptops/sonypi.rst
 
+	spectre_bhi=	[X86] Control mitigation of Branch History Injection
+			(BHI) vulnerability.  This setting affects the
+			deployment of the HW BHI control and the SW BHB
+			clearing sequence.
+
+			on   - (default) Enable the HW or SW mitigation
+			       as needed.
+			off  - Disable the mitigation.
+
 	spectre_v2=	[X86] Control mitigation of Spectre variant 2
 			(indirect branch speculation) vulnerability.
 			The default operation protects the kernel from
@@ -5261,8 +5461,13 @@
 			Specific mitigations can also be selected manually:
 
 			retpoline	  - replace indirect branches
-			retpoline,generic - google's original retpoline
-			retpoline,amd     - AMD-specific minimal thunk
+			retpoline,generic - Retpolines
+			retpoline,lfence  - LFENCE; indirect branch
+			retpoline,amd     - alias for retpoline,lfence
+			eibrs		  - Enhanced/Auto IBRS
+			eibrs,retpoline   - Enhanced/Auto IBRS + Retpolines
+			eibrs,lfence      - Enhanced/Auto IBRS + LFENCE
+			ibrs		  - use IBRS to protect kernel
 
 			Not specifying this option is equivalent to
 			spectre_v2=auto.
@@ -5309,6 +5514,17 @@
 			Not specifying this option is equivalent to
 			spectre_v2_user=auto.
 
+	spec_rstack_overflow=
+			[X86] Control RAS overflow mitigation on AMD Zen CPUs
+
+			off		- Disable mitigation
+			microcode	- Enable microcode mitigation only
+			safe-ret	- Enable sw-only safe RET mitigation (default)
+			ibpb		- Enable mitigation by issuing IBPB on
+					  kernel entry
+			ibpb-vmexit	- Issue IBPB only on VMEXIT
+					  (cloud-specific mitigation)
+
 	spec_store_bypass_disable=
 			[HW] Control Speculative Store Bypass (SSB) Disable mitigation
 			(Speculative Store Bypass vulnerability)
@@ -5497,6 +5713,15 @@
 	stifb=		[HW]
 			Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
 
+        strict_sas_size=
+			[X86]
+			Format: <bool>
+			Enable or disable strict sigaltstack size checks
+			against the required signal frame size which
+			depends on the supported FPU features. This can
+			be used to filter out binaries which have
+			not yet been made aware of AT_MINSIGSTKSZ.
+
 	sunrpc.min_resvport=
 	sunrpc.max_resvport=
 			[NFS,SUNRPC]
@@ -5618,10 +5843,6 @@
 			-1: disable all critical trip points in all thermal zones
 			<degrees C>: override all critical trip points
 
-	thermal.nocrt=	[HW,ACPI]
-			Set to disable actions on ACPI thermal zone
-			critical and hot trip points.
-
 	thermal.off=	[HW,ACPI]
 			1: disable ACPI thermal control
 
@@ -5772,6 +5993,16 @@
 			first trust source as a backend which is initialized
 			successfully during iteration.
 
+	trusted.rng=	[KEYS]
+			Format: <string>
+			The RNG used to generate key material for trusted keys.
+			Can be one of:
+			- "kernel"
+			- the same value as trusted.source: "tpm" or "tee"
+			- "default"
+			If not specified, "default" is used. In this case,
+			the RNG's choice is left to each individual trust source.
+
 	tsc=		Disable clocksource stability checks for TSC.
 			Format: <string>
 			[x86] reliable: mark tsc clocksource as reliable, this
@@ -6349,6 +6580,13 @@
 			improve timer resolution at the expense of processing
 			more timer interrupts.
 
+	xen.balloon_boot_timeout= [XEN]
+			The time (in seconds) to wait before giving up to boot
+			in case initial ballooning fails to free enough memory.
+			Applies only when running as HVM or PVH guest and
+			started with less memory configured than allowed at
+			max. Default is 180.
+
 	xen.event_eoi_delay=	[XEN]
 			How long to delay EOI handling in case of event
 			storms (jiffies). Default is 10.
@@ -6410,3 +6648,14 @@
 				memory, and other data can't be written using
 				xmon commands.
 			off	xmon is disabled.
+
+	amd_pstate=	[X86]
+			disable
+			  Do not enable amd_pstate as the default
+			  scaling driver for the supported processors
+			passive
+			  Use amd_pstate as a scaling driver, driver requests a
+			  desired performance on this abstract scale and the power
+			  management firmware translates the requests into actual
+			  hardware states (core frequency, data fabric and memory
+			  clocks etc.)
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/mm/pagemap.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/mm/pagemap.rst
@@ -23,7 +23,7 @@
     * Bit  56    page exclusively mapped (since 4.2)
     * Bit  57    pte is uffd-wp write-protected (since 5.13) (see
       :ref:`Documentation/admin-guide/mm/userfaultfd.rst <userfaultfd>`)
-    * Bits 57-60 zero
+    * Bits 58-60 zero
     * Bit  61    page is file-page or shared-anon (since 3.5)
     * Bit  62    page swapped
     * Bit  63    page present
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/pm/amd-pstate.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/pm/amd-pstate.rst
@@ -0,0 +1,479 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. include:: <isonum.txt>
+
+===============================================
+``amd-pstate`` CPU Performance Scaling Driver
+===============================================
+
+:Copyright: |copy| 2021 Advanced Micro Devices, Inc.
+
+:Author: Huang Rui <ray.huang@amd.com>
+
+
+Introduction
+===================
+
+``amd-pstate`` is the AMD CPU performance scaling driver that introduces a
+new CPU frequency control mechanism on modern AMD APU and CPU series in
+Linux kernel. The new mechanism is based on Collaborative Processor
+Performance Control (CPPC) which provides finer grain frequency management
+than legacy ACPI hardware P-States. Current AMD CPU/APU platforms are using
+the ACPI P-states driver to manage CPU frequency and clocks with switching
+only in 3 P-states. CPPC replaces the ACPI P-states controls and allows a
+flexible, low-latency interface for the Linux kernel to directly
+communicate the performance hints to hardware.
+
+``amd-pstate`` leverages the Linux kernel governors such as ``schedutil``,
+``ondemand``, etc. to manage the performance hints which are provided by
+CPPC hardware functionality that internally follows the hardware
+specification (for details refer to AMD64 Architecture Programmer's Manual
+Volume 2: System Programming [1]_). Currently, ``amd-pstate`` supports basic
+frequency control function according to kernel governors on some of the
+Zen2 and Zen3 processors, and we will implement more AMD specific functions
+in future after we verify them on the hardware and SBIOS.
+
+
+AMD CPPC Overview
+=======================
+
+Collaborative Processor Performance Control (CPPC) interface enumerates a
+continuous, abstract, and unit-less performance value in a scale that is
+not tied to a specific performance state / frequency. This is an ACPI
+standard [2]_ which software can specify application performance goals and
+hints as a relative target to the infrastructure limits. AMD processors
+provide the low latency register model (MSR) instead of an AML code
+interpreter for performance adjustments. ``amd-pstate`` will initialize a
+``struct cpufreq_driver`` instance, ``amd_pstate_driver``, with the callbacks
+to manage each performance update behavior. ::
+
+ Highest Perf ------>+-----------------------+                         +-----------------------+
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |          Max Perf  ---->|                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+ Nominal Perf ------>+-----------------------+                         +-----------------------+
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |      Desired Perf  ---->|                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+  Lowest non-        |                       |                         |                       |
+  linear perf ------>+-----------------------+                         +-----------------------+
+                     |                       |                         |                       |
+                     |                       |       Lowest perf  ---->|                       |
+                     |                       |                         |                       |
+  Lowest perf ------>+-----------------------+                         +-----------------------+
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+                     |                       |                         |                       |
+          0   ------>+-----------------------+                         +-----------------------+
+
+                                     AMD P-States Performance Scale
+
+
+.. _perf_cap:
+
+AMD CPPC Performance Capability
+--------------------------------
+
+Highest Performance (RO)
+.........................
+
+This is the absolute maximum performance an individual processor may reach,
+assuming ideal conditions. This performance level may not be sustainable
+for long durations and may only be achievable if other platform components
+are in a specific state; for example, it may require other processors to be in
+an idle state. This would be equivalent to the highest frequencies
+supported by the processor.
+
+Nominal (Guaranteed) Performance (RO)
+......................................
+
+This is the maximum sustained performance level of the processor, assuming
+ideal operating conditions. In the absence of an external constraint (power,
+thermal, etc.), this is the performance level the processor is expected to
+be able to maintain continuously. All cores/processors are expected to be
+able to sustain their nominal performance state simultaneously.
+
+Lowest non-linear Performance (RO)
+...................................
+
+This is the lowest performance level at which nonlinear power savings are
+achieved, for example, due to the combined effects of voltage and frequency
+scaling. Above this threshold, lower performance levels should be generally
+more energy efficient than higher performance levels. This register
+effectively conveys the most efficient performance level to ``amd-pstate``.
+
+Lowest Performance (RO)
+........................
+
+This is the absolute lowest performance level of the processor. Selecting a
+performance level lower than the lowest nonlinear performance level may
+cause an efficiency penalty but should reduce the instantaneous power
+consumption of the processor.
+
+AMD CPPC Performance Control
+------------------------------
+
+``amd-pstate`` passes performance goals through these registers. The
+register drives the behavior of the desired performance target.
+
+Minimum requested performance (RW)
+...................................
+
+``amd-pstate`` specifies the minimum allowed performance level.
+
+Maximum requested performance (RW)
+...................................
+
+``amd-pstate`` specifies a limit the maximum performance that is expected
+to be supplied by the hardware.
+
+Desired performance target (RW)
+...................................
+
+``amd-pstate`` specifies a desired target in the CPPC performance scale as
+a relative number. This can be expressed as percentage of nominal
+performance (infrastructure max). Below the nominal sustained performance
+level, desired performance expresses the average performance level of the
+processor subject to hardware. Above the nominal performance level,
+the processor must provide at least nominal performance requested and go higher
+if current operating conditions allow.
+
+Energy Performance Preference (EPP) (RW)
+.........................................
+
+This attribute provides a hint to the hardware if software wants to bias
+toward performance (0x0) or energy efficiency (0xff).
+
+
+Key Governors Support
+=======================
+
+``amd-pstate`` can be used with all the (generic) scaling governors listed
+by the ``scaling_available_governors`` policy attribute in ``sysfs``. Then,
+it is responsible for the configuration of policy objects corresponding to
+CPUs and provides the ``CPUFreq`` core (and the scaling governors attached
+to the policy objects) with accurate information on the maximum and minimum
+operating frequencies supported by the hardware. Users can check the
+``scaling_cur_freq`` information comes from the ``CPUFreq`` core.
+
+``amd-pstate`` mainly supports ``schedutil`` and ``ondemand`` for dynamic
+frequency control. It is to fine tune the processor configuration on
+``amd-pstate`` to the ``schedutil`` with CPU CFS scheduler. ``amd-pstate``
+registers the adjust_perf callback to implement performance update behavior
+similar to CPPC. It is initialized by ``sugov_start`` and then populates the
+CPU's update_util_data pointer to assign ``sugov_update_single_perf`` as the
+utilization update callback function in the CPU scheduler. The CPU scheduler
+will call ``cpufreq_update_util`` and assigns the target performance according
+to the ``struct sugov_cpu`` that the utilization update belongs to.
+Then, ``amd-pstate`` updates the desired performance according to the CPU
+scheduler assigned.
+
+.. _processor_support:
+
+Processor Support
+=======================
+
+The ``amd-pstate`` initialization will fail if the ``_CPC`` entry in the ACPI
+SBIOS does not exist in the detected processor. It uses ``acpi_cpc_valid``
+to check the existence of ``_CPC``. All Zen based processors support the legacy
+ACPI hardware P-States function, so when ``amd-pstate`` fails initialization,
+the kernel will fall back to initialize the ``acpi-cpufreq`` driver.
+
+There are two types of hardware implementations for ``amd-pstate``: one is
+`Full MSR Support <perf_cap_>`_ and another is `Shared Memory Support
+<perf_cap_>`_. It can use the :c:macro:`X86_FEATURE_CPPC` feature flag to
+indicate the different types. (For details, refer to the Processor Programming
+Reference (PPR) for AMD Family 19h Model 51h, Revision A1 Processors [3]_.)
+``amd-pstate`` is to register different ``static_call`` instances for different
+hardware implementations.
+
+Currently, some of the Zen2 and Zen3 processors support ``amd-pstate``. In the
+future, it will be supported on more and more AMD processors.
+
+Full MSR Support
+-----------------
+
+Some new Zen3 processors such as Cezanne provide the MSR registers directly
+while the :c:macro:`X86_FEATURE_CPPC` CPU feature flag is set.
+``amd-pstate`` can handle the MSR register to implement the fast switch
+function in ``CPUFreq`` that can reduce the latency of frequency control in
+interrupt context. The functions with a ``pstate_xxx`` prefix represent the
+operations on MSR registers.
+
+Shared Memory Support
+----------------------
+
+If the :c:macro:`X86_FEATURE_CPPC` CPU feature flag is not set, the
+processor supports the shared memory solution. In this case, ``amd-pstate``
+uses the ``cppc_acpi`` helper methods to implement the callback functions
+that are defined on ``static_call``. The functions with the ``cppc_xxx`` prefix
+represent the operations of ACPI CPPC helpers for the shared memory solution.
+
+
+AMD P-States and ACPI hardware P-States always can be supported in one
+processor. But AMD P-States has the higher priority and if it is enabled
+with :c:macro:`MSR_AMD_CPPC_ENABLE` or ``cppc_set_enable``, it will respond
+to the request from AMD P-States.
+
+
+User Space Interface in ``sysfs``
+==================================
+
+``amd-pstate`` exposes several global attributes (files) in ``sysfs`` to
+control its functionality at the system level. They are located in the
+``/sys/devices/system/cpu/cpufreq/policyX/`` directory and affect all CPUs. ::
+
+ root@hr-test1:/home/ray# ls /sys/devices/system/cpu/cpufreq/policy0/*amd*
+ /sys/devices/system/cpu/cpufreq/policy0/amd_pstate_highest_perf
+ /sys/devices/system/cpu/cpufreq/policy0/amd_pstate_lowest_nonlinear_freq
+ /sys/devices/system/cpu/cpufreq/policy0/amd_pstate_max_freq
+
+
+``amd_pstate_highest_perf / amd_pstate_max_freq``
+
+Maximum CPPC performance and CPU frequency that the driver is allowed to
+set, in percent of the maximum supported CPPC performance level (the highest
+performance supported in `AMD CPPC Performance Capability <perf_cap_>`_).
+In some ASICs, the highest CPPC performance is not the one in the ``_CPC``
+table, so we need to expose it to sysfs. If boost is not active, but
+still supported, this maximum frequency will be larger than the one in
+``cpuinfo``.
+This attribute is read-only.
+
+``amd_pstate_lowest_nonlinear_freq``
+
+The lowest non-linear CPPC CPU frequency that the driver is allowed to set,
+in percent of the maximum supported CPPC performance level. (Please see the
+lowest non-linear performance in `AMD CPPC Performance Capability
+<perf_cap_>`_.)
+This attribute is read-only.
+
+Other performance and frequency values can be read back from
+``/sys/devices/system/cpu/cpuX/acpi_cppc/``, see :ref:`cppc_sysfs`.
+
+
+``amd-pstate`` vs ``acpi-cpufreq``
+======================================
+
+On the majority of AMD platforms supported by ``acpi-cpufreq``, the ACPI tables
+provided by the platform firmware are used for CPU performance scaling, but
+only provide 3 P-states on AMD processors.
+However, on modern AMD APU and CPU series, hardware provides the Collaborative
+Processor Performance Control according to the ACPI protocol and customizes this
+for AMD platforms. That is, fine-grained and continuous frequency ranges
+instead of the legacy hardware P-states. ``amd-pstate`` is the kernel
+module which supports the new AMD P-States mechanism on most of the future AMD
+platforms. The AMD P-States mechanism is the more performance and energy
+efficiency frequency management method on AMD processors.
+
+Kernel Module Options for ``amd-pstate``
+=========================================
+
+Passive Mode
+------------
+
+``amd_pstate=passive``
+
+It will be enabled if the ``amd_pstate=passive`` is passed to the kernel in the command line.
+In this mode, ``amd_pstate`` driver software specifies a desired QoS target in the CPPC
+performance scale as a relative number. This can be expressed as percentage of nominal
+performance (infrastructure max). Below the nominal sustained performance level,
+desired performance expresses the average performance level of the processor subject
+to the Performance Reduction Tolerance register. Above the nominal performance level,
+processor must provide at least nominal performance requested and go higher if current
+operating conditions allow.
+
+
+``cpupower`` tool support for ``amd-pstate``
+===============================================
+
+``amd-pstate`` is supported by the ``cpupower`` tool, which can be used to dump
+frequency information. Development is in progress to support more and more
+operations for the new ``amd-pstate`` module with this tool. ::
+
+ root@hr-test1:/home/ray# cpupower frequency-info
+ analyzing CPU 0:
+   driver: amd-pstate
+   CPUs which run at the same hardware frequency: 0
+   CPUs which need to have their frequency coordinated by software: 0
+   maximum transition latency: 131 us
+   hardware limits: 400 MHz - 4.68 GHz
+   available cpufreq governors: ondemand conservative powersave userspace performance schedutil
+   current policy: frequency should be within 400 MHz and 4.68 GHz.
+                   The governor "schedutil" may decide which speed to use
+                   within this range.
+   current CPU frequency: Unable to call hardware
+   current CPU frequency: 4.02 GHz (asserted by call to kernel)
+   boost state support:
+     Supported: yes
+     Active: yes
+     AMD PSTATE Highest Performance: 166. Maximum Frequency: 4.68 GHz.
+     AMD PSTATE Nominal Performance: 117. Nominal Frequency: 3.30 GHz.
+     AMD PSTATE Lowest Non-linear Performance: 39. Lowest Non-linear Frequency: 1.10 GHz.
+     AMD PSTATE Lowest Performance: 15. Lowest Frequency: 400 MHz.
+
+
+Diagnostics and Tuning
+=======================
+
+Trace Events
+--------------
+
+There are two static trace events that can be used for ``amd-pstate``
+diagnostics. One of them is the ``cpu_frequency`` trace event generally used
+by ``CPUFreq``, and the other one is the ``amd_pstate_perf`` trace event
+specific to ``amd-pstate``.  The following sequence of shell commands can
+be used to enable them and see their output (if the kernel is
+configured to support event tracing). ::
+
+ root@hr-test1:/home/ray# cd /sys/kernel/tracing/
+ root@hr-test1:/sys/kernel/tracing# echo 1 > events/amd_cpu/enable
+ root@hr-test1:/sys/kernel/tracing# cat trace
+ # tracer: nop
+ #
+ # entries-in-buffer/entries-written: 47827/42233061   #P:2
+ #
+ #                                _-----=> irqs-off
+ #                               / _----=> need-resched
+ #                              | / _---=> hardirq/softirq
+ #                              || / _--=> preempt-depth
+ #                              ||| /     delay
+ #           TASK-PID     CPU#  ||||   TIMESTAMP  FUNCTION
+ #              | |         |   ||||      |         |
+          <idle>-0       [015] dN...  4995.979886: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=15 changed=false fast_switch=true
+          <idle>-0       [007] d.h..  4995.979893: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=7 changed=false fast_switch=true
+             cat-2161    [000] d....  4995.980841: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=0 changed=false fast_switch=true
+            sshd-2125    [004] d.s..  4995.980968: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=4 changed=false fast_switch=true
+          <idle>-0       [007] d.s..  4995.980968: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=7 changed=false fast_switch=true
+          <idle>-0       [003] d.s..  4995.980971: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=3 changed=false fast_switch=true
+          <idle>-0       [011] d.s..  4995.980996: amd_pstate_perf: amd_min_perf=85 amd_des_perf=85 amd_max_perf=166 cpu_id=11 changed=false fast_switch=true
+
+The ``cpu_frequency`` trace event will be triggered either by the ``schedutil`` scaling
+governor (for the policies it is attached to), or by the ``CPUFreq`` core (for the
+policies with other scaling governors).
+
+
+Tracer Tool
+-------------
+
+``amd_pstate_tracer.py`` can record and parse ``amd-pstate`` trace log, then
+generate performance plots. This utility can be used to debug and tune the
+performance of ``amd-pstate`` driver. The tracer tool needs to import intel
+pstate tracer.
+
+Tracer tool located in ``linux/tools/power/x86/amd_pstate_tracer``. It can be
+used in two ways. If trace file is available, then directly parse the file
+with command ::
+
+ ./amd_pstate_trace.py [-c cpus] -t <trace_file> -n <test_name>
+
+Or generate trace file with root privilege, then parse and plot with command ::
+
+ sudo ./amd_pstate_trace.py [-c cpus] -n <test_name> -i <interval> [-m kbytes]
+
+The test result can be found in ``results/test_name``. Following is the example
+about part of the output. ::
+
+ common_cpu  common_secs  common_usecs  min_perf  des_perf  max_perf  freq    mperf   apef    tsc       load   duration_ms  sample_num  elapsed_time  common_comm
+ CPU_005     712          116384        39        49        166       0.7565  9645075 2214891 38431470  25.1   11.646       469         2.496         kworker/5:0-40
+ CPU_006     712          116408        39        49        166       0.6769  8950227 1839034 37192089  24.06  11.272       470         2.496         kworker/6:0-1264
+
+Unit Tests for amd-pstate
+-------------------------
+
+``amd-pstate-ut`` is a test module for testing the ``amd-pstate`` driver.
+
+ * It can help all users to verify their processor support (SBIOS/Firmware or Hardware).
+
+ * Kernel can have a basic function test to avoid the kernel regression during the update.
+
+ * We can introduce more functional or performance tests to align the result together, it will benefit power and performance scale optimization.
+
+1. Test case decriptions
+
+        +---------+--------------------------------+------------------------------------------------------------------------------------+
+        | Index   | Functions                      | Description                                                                        |
+        +=========+================================+====================================================================================+
+        | 0       | amd_pstate_ut_acpi_cpc_valid   || Check whether the _CPC object is present in SBIOS.                                |
+        |         |                                ||                                                                                   |
+        |         |                                || The detail refer to `Processor Support <processor_support_>`_.                    |
+        +---------+--------------------------------+------------------------------------------------------------------------------------+
+        | 1       | amd_pstate_ut_check_enabled    || Check whether AMD P-State is enabled.                                             |
+        |         |                                ||                                                                                   |
+        |         |                                || AMD P-States and ACPI hardware P-States always can be supported in one processor. |
+        |         |                                | But AMD P-States has the higher priority and if it is enabled with                 |
+        |         |                                | :c:macro:`MSR_AMD_CPPC_ENABLE` or ``cppc_set_enable``, it will respond to the      |
+        |         |                                | request from AMD P-States.                                                         |
+        +---------+--------------------------------+------------------------------------------------------------------------------------+
+        | 2       | amd_pstate_ut_check_perf       || Check if the each performance values are reasonable.                              |
+        |         |                                || highest_perf >= nominal_perf > lowest_nonlinear_perf > lowest_perf > 0.           |
+        +---------+--------------------------------+------------------------------------------------------------------------------------+
+        | 3       | amd_pstate_ut_check_freq       || Check if the each frequency values and max freq when set support boost mode       |
+        |         |                                | are reasonable.                                                                    |
+        |         |                                || max_freq >= nominal_freq > lowest_nonlinear_freq > min_freq > 0                   |
+        |         |                                || If boost is not active but supported, this maximum frequency will be larger than  |
+        |         |                                | the one in ``cpuinfo``.                                                            |
+        +---------+--------------------------------+------------------------------------------------------------------------------------+
+
+#. How to execute the tests
+
+   We use test module in the kselftest frameworks to implement it.
+   We create amd-pstate-ut module and tie it into kselftest.(for
+   details refer to Linux Kernel Selftests [4]_).
+
+    1. Build
+
+        + open the :c:macro:`CONFIG_X86_AMD_PSTATE` configuration option.
+        + set the :c:macro:`CONFIG_X86_AMD_PSTATE_UT` configuration option to M.
+        + make project
+        + make selftest ::
+
+            $ cd linux
+            $ make -C tools/testing/selftests
+
+    #. Installation & Steps ::
+
+        $ make -C tools/testing/selftests install INSTALL_PATH=~/kselftest
+        $ sudo ./kselftest/run_kselftest.sh -c amd-pstate
+        TAP version 13
+        1..1
+        # selftests: amd-pstate: amd-pstate-ut.sh
+        # amd-pstate-ut: ok
+        ok 1 selftests: amd-pstate: amd-pstate-ut.sh
+
+    #. Results ::
+
+         $ dmesg | grep "amd_pstate_ut" | tee log.txt
+         [12977.570663] amd_pstate_ut: 1    amd_pstate_ut_acpi_cpc_valid  success!
+         [12977.570673] amd_pstate_ut: 2    amd_pstate_ut_check_enabled   success!
+         [12977.571207] amd_pstate_ut: 3    amd_pstate_ut_check_perf      success!
+         [12977.571212] amd_pstate_ut: 4    amd_pstate_ut_check_freq      success!
+
+Reference
+===========
+
+.. [1] AMD64 Architecture Programmer's Manual Volume 2: System Programming,
+       https://www.amd.com/system/files/TechDocs/24593.pdf
+
+.. [2] Advanced Configuration and Power Interface Specification,
+       https://uefi.org/sites/default/files/resources/ACPI_Spec_6_4_Jan22.pdf
+
+.. [3] Processor Programming Reference (PPR) for AMD Family 19h Model 51h, Revision A1 Processors
+       https://www.amd.com/system/files/TechDocs/56569-A1-PUB.zip
+
+.. [4] Linux Kernel Selftests,
+       https://www.kernel.org/doc/html/latest/dev-tools/kselftest.html
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/pm/cpuidle.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/pm/cpuidle.rst
@@ -612,8 +612,8 @@
 by default this way, for example.
 
 The other kernel command line parameters controlling CPU idle time management
-described below are only relevant for the *x86* architecture and some of
-them affect Intel processors only.
+described below are only relevant for the *x86* architecture and references
+to ``intel_idle`` affect Intel processors only.
 
 The *x86* architecture support code recognizes three kernel command line
 options related to CPU idle time management: ``idle=poll``, ``idle=halt``,
@@ -635,10 +635,13 @@
 energy-efficiency.  Thus using it for performance reasons may not be a good idea
 at all.]
 
-The ``idle=nomwait`` option disables the ``intel_idle`` driver and causes
-``acpi_idle`` to be used (as long as all of the information needed by it is
-there in the system's ACPI tables), but it is not allowed to use the
-``MWAIT`` instruction of the CPUs to ask the hardware to enter idle states.
+The ``idle=nomwait`` option prevents the use of ``MWAIT`` instruction of
+the CPU to enter idle states. When this option is used, the ``acpi_idle``
+driver will use the ``HLT`` instruction instead of ``MWAIT``. On systems
+running Intel processors, this option disables the ``intel_idle`` driver
+and forces the use of the ``acpi_idle`` driver instead. Note that in either
+case, ``acpi_idle`` driver will function only if all the information needed
+by it is in the system's ACPI tables.
 
 In addition to the architecture-level kernel command line options affecting CPU
 idle time management, there are parameters affecting individual ``CPUIdle``
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/pm/working-state.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/pm/working-state.rst
@@ -11,6 +11,7 @@
    intel_idle
    cpufreq
    intel_pstate
+   amd-pstate
    cpufreq_drivers
    intel_epb
    intel-speed-select
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/security-bugs.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/security-bugs.rst
@@ -63,31 +63,28 @@
 of the report are treated confidentially even after the embargo has been
 lifted, in perpetuity.
 
-Coordination
-------------
+Coordination with other groups
+------------------------------
 
-Fixes for sensitive bugs, such as those that might lead to privilege
-escalations, may need to be coordinated with the private
-<linux-distros@vs.openwall.org> mailing list so that distribution vendors
-are well prepared to issue a fixed kernel upon public disclosure of the
-upstream fix. Distros will need some time to test the proposed patch and
-will generally request at least a few days of embargo, and vendor update
-publication prefers to happen Tuesday through Thursday. When appropriate,
-the security team can assist with this coordination, or the reporter can
-include linux-distros from the start. In this case, remember to prefix
-the email Subject line with "[vs]" as described in the linux-distros wiki:
-<http://oss-security.openwall.org/wiki/mailing-lists/distros#how-to-use-the-lists>
+The kernel security team strongly recommends that reporters of potential
+security issues NEVER contact the "linux-distros" mailing list until
+AFTER discussing it with the kernel security team.  Do not Cc: both
+lists at once.  You may contact the linux-distros mailing list after a
+fix has been agreed on and you fully understand the requirements that
+doing so will impose on you and the kernel community.
+
+The different lists have different goals and the linux-distros rules do
+not contribute to actually fixing any potential security problems.
 
 CVE assignment
 --------------
 
-The security team does not normally assign CVEs, nor do we require them
-for reports or fixes, as this can needlessly complicate the process and
-may delay the bug handling. If a reporter wishes to have a CVE identifier
-assigned ahead of public disclosure, they will need to contact the private
-linux-distros list, described above. When such a CVE identifier is known
-before a patch is provided, it is desirable to mention it in the commit
-message if the reporter agrees.
+The security team does not assign CVEs, nor do we require them for
+reports or fixes, as this can needlessly complicate the process and may
+delay the bug handling.  If a reporter wishes to have a CVE identifier
+assigned, they should find one by themselves, for example by contacting
+MITRE directly.  However under no circumstances will a patch inclusion
+be delayed to wait for a CVE identifier to arrive.
 
 Non-disclosure agreements
 -------------------------
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/sysctl/kernel.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/sysctl/kernel.rst
@@ -442,6 +442,35 @@
 ``IA64_THREAD_UAC_NOPRINT`` ``prctl`` and avoid logs being flooded.
 
 
+io_uring_disabled
+=================
+
+Prevents all processes from creating new io_uring instances. Enabling this
+shrinks the kernel's attack surface.
+
+= ======================================================================
+0 All processes can create io_uring instances as normal. This is the
+  default setting.
+1 io_uring creation is disabled (io_uring_setup() will fail with
+  -EPERM) for unprivileged processes not in the io_uring_group group.
+  Existing io_uring instances can still be used.  See the
+  documentation for io_uring_group for more information.
+2 io_uring creation is disabled for all processes. io_uring_setup()
+  always fails with -EPERM. Existing io_uring instances can still be
+  used.
+= ======================================================================
+
+
+io_uring_group
+==============
+
+When io_uring_disabled is set to 1, a process must either be
+privileged (CAP_SYS_ADMIN) or be in the io_uring_group group in order
+to create an io_uring instance.  If io_uring_group is set to -1 (the
+default), only processes with the CAP_SYS_ADMIN capability may create
+io_uring instances.
+
+
 kexec_load_disabled
 ===================
 
@@ -671,6 +700,15 @@
 an oops event is detected.
 
 
+oops_limit
+==========
+
+Number of kernel oopses after which the kernel should panic when
+``panic_on_oops`` is not set. Setting this to 0 disables checking
+the count. Setting this to  1 has the same effect as setting
+``panic_on_oops=1``. The default value is 10000.
+
+
 osrelease, ostype & version
 ===========================
 
@@ -795,6 +833,7 @@
 bit 2  print timer info
 bit 3  print locks info if ``CONFIG_LOCKDEP`` is on
 bit 4  print ftrace buffer
+bit 5  print all printk messages in buffer
 =====  ============================================
 
 So for example to print tasks and memory info on panic, user can::
@@ -1013,28 +1052,22 @@
 * ``boot_id``: a UUID generated the first time this is retrieved, and
   unvarying after that;
 
+* ``uuid``: a UUID generated every time this is retrieved (this can
+  thus be used to generate UUIDs at will);
+
 * ``entropy_avail``: the pool's entropy count, in bits;
 
 * ``poolsize``: the entropy pool size, in bits;
 
 * ``urandom_min_reseed_secs``: obsolete (used to determine the minimum
-  number of seconds between urandom pool reseeding).
-
-* ``uuid``: a UUID generated every time this is retrieved (this can
-  thus be used to generate UUIDs at will);
+  number of seconds between urandom pool reseeding). This file is
+  writable for compatibility purposes, but writing to it has no effect
+  on any RNG behavior;
 
 * ``write_wakeup_threshold``: when the entropy count drops below this
   (as a number of bits), processes waiting to write to ``/dev/random``
-  are woken up.
-
-If ``drivers/char/random.c`` is built with ``ADD_INTERRUPT_BENCH``
-defined, these additional entries are present:
-
-* ``add_interrupt_avg_cycles``: the average number of cycles between
-  interrupts used to feed the pool;
-
-* ``add_interrupt_avg_deviation``: the standard deviation seen on the
-  number of cycles between interrupts used to feed the pool.
+  are woken up. This file is writable for compatibility purposes, but
+  writing to it has no effect on any RNG behavior.
 
 
 randomize_va_space
@@ -1099,7 +1132,7 @@
 ===============
 
 Enables/disables task delay accounting (see
-:doc:`accounting/delay-accounting.rst`). Enabling this feature incurs
+Documentation/accounting/delay-accounting.rst. Enabling this feature incurs
 a small amount of overhead in the scheduler but is useful for debugging
 and performance tuning. It is required by some tools such as iotop.
 
@@ -1490,6 +1523,16 @@
 2 Unprivileged calls to ``bpf()`` are disabled
 = =============================================================
 
+
+warn_limit
+==========
+
+Number of kernel warnings after which the kernel should panic when
+``panic_on_warn`` is not set. Setting this to 0 disables checking
+the warning count. Setting this to 1 has the same effect as setting
+``panic_on_warn=1``. The default value is 0.
+
+
 watchdog
 ========
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/sysctl/net.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/sysctl/net.rst
@@ -31,17 +31,18 @@
 
 Table : Subdirectories in /proc/sys/net
 
- ========= =================== = ========== ==================
+ ========= =================== = ========== ===================
  Directory Content               Directory  Content
- ========= =================== = ========== ==================
- core      General parameter     appletalk  Appletalk protocol
- unix      Unix domain sockets   netrom     NET/ROM
- 802       E802 protocol         ax25       AX25
- ethernet  Ethernet protocol     rose       X.25 PLP layer
+ ========= =================== = ========== ===================
+ 802       E802 protocol         mptcp      Multipath TCP
+ appletalk Appletalk protocol    netfilter  Network Filter
+ ax25      AX25                  netrom     NET/ROM
+ bridge    Bridging              rose       X.25 PLP layer
+ core      General parameter     tipc       TIPC
+ ethernet  Ethernet protocol     unix       Unix domain sockets
  ipv4      IP version 4          x25        X.25 protocol
- bridge    Bridging              decnet     DEC net
- ipv6      IP version 6          tipc       TIPC
- ========= =================== = ========== ==================
+ ipv6      IP version 6
+ ========= =================== = ========== ===================
 
 1. /proc/sys/net/core - Network core options
 ============================================
@@ -271,7 +272,7 @@
 netdev_max_backlog
 ------------------
 
-Maximum number  of  packets,  queued  on  the  INPUT  side, when the interface
+Maximum number of packets, queued on the INPUT side, when the interface
 receives packets faster than kernel can process them.
 
 netdev_rss_key
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/admin-guide/sysctl/vm.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/admin-guide/sysctl/vm.rst
@@ -948,7 +948,7 @@
 
 The unit is in fractions of 10,000. The default value of 10 means the
 distances between watermarks are 0.1% of the available memory in the
-node/system. The maximum value is 1000, or 10% of memory.
+node/system. The maximum value is 3000, or 30% of memory.
 
 A high rate of threads entering direct reclaim (allocstall) or kswapd
 going to sleep prematurely (kswapd_low_wmark_hit_quickly) can indicate
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/arm64/cpu-feature-registers.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/arm64/cpu-feature-registers.rst
@@ -92,7 +92,7 @@
 
 The infrastructure emulates only the following system register space::
 
-	Op0=3, Op1=0, CRn=0, CRm=0,4,5,6,7
+	Op0=3, Op1=0, CRn=0, CRm=0,2,3,4,5,6,7
 
 (See Table C5-6 'System instruction encodings for non-Debug System
 register accesses' in ARMv8 ARM DDI 0487A.h, for the list of
@@ -235,7 +235,15 @@
      | DPB                          | [3-0]   |    y    |
      +------------------------------+---------+---------+
 
-  6) ID_AA64MMFR2_EL1 - Memory model feature register 2
+  6) ID_AA64MMFR0_EL1 - Memory model feature register 0
+
+     +------------------------------+---------+---------+
+     | Name                         |  bits   | visible |
+     +------------------------------+---------+---------+
+     | ECV                          | [63-60] |    y    |
+     +------------------------------+---------+---------+
+
+  7) ID_AA64MMFR2_EL1 - Memory model feature register 2
 
      +------------------------------+---------+---------+
      | Name                         |  bits   | visible |
@@ -243,7 +251,7 @@
      | AT                           | [35-32] |    y    |
      +------------------------------+---------+---------+
 
-  7) ID_AA64ZFR0_EL1 - SVE feature ID register 0
+  8) ID_AA64ZFR0_EL1 - SVE feature ID register 0
 
      +------------------------------+---------+---------+
      | Name                         |  bits   | visible |
@@ -267,6 +275,59 @@
      | SVEVer                       | [3-0]   |    y    |
      +------------------------------+---------+---------+
 
+  8) ID_AA64MMFR1_EL1 - Memory model feature register 1
+
+     +------------------------------+---------+---------+
+     | Name                         |  bits   | visible |
+     +------------------------------+---------+---------+
+     | AFP                          | [47-44] |    y    |
+     +------------------------------+---------+---------+
+
+  9) ID_AA64ISAR2_EL1 - Instruction set attribute register 2
+
+     +------------------------------+---------+---------+
+     | Name                         |  bits   | visible |
+     +------------------------------+---------+---------+
+     | RPRES                        | [7-4]   |    y    |
+     +------------------------------+---------+---------+
+
+  10) MVFR0_EL1 - AArch32 Media and VFP Feature Register 0
+
+     +------------------------------+---------+---------+
+     | Name                         |  bits   | visible |
+     +------------------------------+---------+---------+
+     | FPDP                         | [11-8]  |    y    |
+     +------------------------------+---------+---------+
+
+  11) MVFR1_EL1 - AArch32 Media and VFP Feature Register 1
+
+     +------------------------------+---------+---------+
+     | Name                         |  bits   | visible |
+     +------------------------------+---------+---------+
+     | SIMDFMAC                     | [31-28] |    y    |
+     +------------------------------+---------+---------+
+     | SIMDSP                       | [19-16] |    y    |
+     +------------------------------+---------+---------+
+     | SIMDInt                      | [15-12] |    y    |
+     +------------------------------+---------+---------+
+     | SIMDLS                       | [11-8]  |    y    |
+     +------------------------------+---------+---------+
+
+  12) ID_ISAR5_EL1 - AArch32 Instruction Set Attribute Register 5
+
+     +------------------------------+---------+---------+
+     | Name                         |  bits   | visible |
+     +------------------------------+---------+---------+
+     | CRC32                        | [19-16] |    y    |
+     +------------------------------+---------+---------+
+     | SHA2                         | [15-12] |    y    |
+     +------------------------------+---------+---------+
+     | SHA1                         | [11-8]  |    y    |
+     +------------------------------+---------+---------+
+     | AES                          | [7-4]   |    y    |
+     +------------------------------+---------+---------+
+
+
 Appendix I: Example
 -------------------
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/arm64/elf_hwcaps.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/arm64/elf_hwcaps.rst
@@ -247,6 +247,18 @@
     Functionality implied by ID_AA64PFR1_EL1.MTE == 0b0010, as described
     by Documentation/arm64/memory-tagging-extension.rst.
 
+HWCAP2_ECV
+
+    Functionality implied by ID_AA64MMFR0_EL1.ECV == 0b0001.
+
+HWCAP2_AFP
+
+    Functionality implied by ID_AA64MFR1_EL1.AFP == 0b0001.
+
+HWCAP2_RPRES
+
+    Functionality implied by ID_AA64ISAR2_EL1.RPRES == 0b0001.
+
 4. Unused AT_HWCAP bits
 -----------------------
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/arm64/silicon-errata.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/arm64/silicon-errata.rst
@@ -68,6 +68,8 @@
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A55      | #1530923        | ARM64_ERRATUM_1530923       |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A55      | #2441007        | ARM64_ERRATUM_2441007       |
++----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A57      | #832075         | ARM64_ERRATUM_832075        |
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A57      | #852523         | N/A                         |
@@ -76,10 +78,14 @@
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A57      | #1319537        | ARM64_ERRATUM_1319367       |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A57      | #1742098        | ARM64_ERRATUM_1742098       |
++----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A72      | #853709         | N/A                         |
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A72      | #1319367        | ARM64_ERRATUM_1319367       |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A72      | #1655431        | ARM64_ERRATUM_1742098       |
++----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A73      | #858921         | ARM64_ERRATUM_858921        |
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A76      | #1188873,1418040| ARM64_ERRATUM_1418040       |
@@ -90,16 +96,76 @@
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A76      | #1463225        | ARM64_ERRATUM_1463225       |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A76      | #3324349        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Cortex-A77      | #1508412        | ARM64_ERRATUM_1508412       |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A77      | #3324348        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A78      | #3324344        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A78C     | #3324346,3324347| ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A510     | #2441009        | ARM64_ERRATUM_2441009       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A510     | #2457168        | ARM64_ERRATUM_2457168       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A710     | #2119858        | ARM64_ERRATUM_2119858       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A710     | #2054223        | ARM64_ERRATUM_2054223       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A710     | #2224489        | ARM64_ERRATUM_2224489       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A710     | #3324338        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A715     | #3456084        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A720     | #3456091        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-A725     | #3456106        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-X1       | #3324344        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-X1C      | #3324346        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-X2       | #3324338        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-X3       | #3324335        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-X4       | #3194386        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Cortex-X925     | #3324334        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Neoverse-N1     | #1188873,1418040| ARM64_ERRATUM_1418040       |
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Neoverse-N1     | #1349291        | N/A                         |
 +----------------+-----------------+-----------------+-----------------------------+
 | ARM            | Neoverse-N1     | #1542419        | ARM64_ERRATUM_1542419       |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-N1     | #3324349        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-N2     | #2139208        | ARM64_ERRATUM_2139208       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-N2     | #2067961        | ARM64_ERRATUM_2067961       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-N2     | #2253138        | ARM64_ERRATUM_2253138       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-N2     | #3324339        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-N3     | #3456111        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-V1     | #3324341        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-V2     | #3324336        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | Neoverse-V3     | #3312417        | ARM64_ERRATUM_3194386       |
++----------------+-----------------+-----------------+-----------------------------+
 | ARM            | MMU-500         | #841119,826419  | N/A                         |
 +----------------+-----------------+-----------------+-----------------------------+
+| ARM            | MMU-600         | #1076982,1209401| N/A                         |
++----------------+-----------------+-----------------+-----------------------------+
+| ARM            | MMU-700         | #2268618,2812531| N/A                         |
++----------------+-----------------+-----------------+-----------------------------+
 +----------------+-----------------+-----------------+-----------------------------+
 | Broadcom       | Brahma-B53      | N/A             | ARM64_ERRATUM_845719        |
 +----------------+-----------------+-----------------+-----------------------------+
@@ -146,6 +212,9 @@
 +----------------+-----------------+-----------------+-----------------------------+
 | Hisilicon      | Hip08 SMMU PMCG | #162001800      | N/A                         |
 +----------------+-----------------+-----------------+-----------------------------+
+| Hisilicon      | Hip08 SMMU PMCG | #162001900      | N/A                         |
+|                | Hip09 SMMU PMCG |                 |                             |
++----------------+-----------------+-----------------+-----------------------------+
 +----------------+-----------------+-----------------+-----------------------------+
 | Qualcomm Tech. | Kryo/Falkor v1  | E1003           | QCOM_FALKOR_ERRATUM_1003    |
 +----------------+-----------------+-----------------+-----------------------------+
@@ -163,6 +232,16 @@
 +----------------+-----------------+-----------------+-----------------------------+
 | Qualcomm Tech. | Kryo4xx Silver  | N/A             | ARM64_ERRATUM_1024718       |
 +----------------+-----------------+-----------------+-----------------------------+
+| Qualcomm Tech. | Kryo4xx Gold    | N/A             | ARM64_ERRATUM_1286807       |
++----------------+-----------------+-----------------+-----------------------------+
+
 +----------------+-----------------+-----------------+-----------------------------+
 | Fujitsu        | A64FX           | E#010001        | FUJITSU_ERRATUM_010001      |
 +----------------+-----------------+-----------------+-----------------------------+
++----------------+-----------------+-----------------+-----------------------------+
+| Microsoft      | Azure Cobalt 100| #2139208        | ARM64_ERRATUM_2139208       |
++----------------+-----------------+-----------------+-----------------------------+
+| Microsoft      | Azure Cobalt 100| #2067961        | ARM64_ERRATUM_2067961       |
++----------------+-----------------+-----------------+-----------------------------+
+| Microsoft      | Azure Cobalt 100| #2253138        | ARM64_ERRATUM_2253138       |
++----------------+-----------------+-----------------+-----------------------------+
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/atomic_bitops.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/atomic_bitops.txt
@@ -59,7 +59,7 @@
  - RMW operations that have a return value are fully ordered.
 
  - RMW operations that are conditional are unordered on FAILURE,
-   otherwise the above rules apply. In the case of test_and_{}_bit() operations,
+   otherwise the above rules apply. In the case of test_and_set_bit_lock(),
    if the bit in memory is unchanged by the operation then it is deemed to have
    failed.
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/cgroups/namespace.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/cgroups/namespace.txt
@@ -0,0 +1,142 @@
+			CGroup Namespaces
+
+CGroup Namespace provides a mechanism to virtualize the view of the
+/proc/<pid>/cgroup file. The CLONE_NEWCGROUP clone-flag can be used with
+clone() and unshare() syscalls to create a new cgroup namespace.
+The process running inside the cgroup namespace will have its /proc/<pid>/cgroup
+output restricted to cgroupns-root. cgroupns-root is the cgroup of the process
+at the time of creation of the cgroup namespace.
+
+Prior to CGroup Namespace, the /proc/<pid>/cgroup file used to show complete
+path of the cgroup of a process. In a container setup (where a set of cgroups
+and namespaces are intended to isolate processes), the /proc/<pid>/cgroup file
+may leak potential system level information to the isolated processes.
+
+For Example:
+  $ cat /proc/self/cgroup
+  0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/batchjobs/container_id1
+
+The path '/batchjobs/container_id1' can generally be considered as system-data
+and its desirable to not expose it to the isolated process.
+
+CGroup Namespaces can be used to restrict visibility of this path.
+For Example:
+  # Before creating cgroup namespace
+  $ ls -l /proc/self/ns/cgroup
+  lrwxrwxrwx 1 root root 0 2014-07-15 10:37 /proc/self/ns/cgroup -> cgroup:[4026531835]
+  $ cat /proc/self/cgroup
+  0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/batchjobs/container_id1
+
+  # unshare(CLONE_NEWCGROUP) and exec /bin/bash
+  $ ~/unshare -c
+  [ns]$ ls -l /proc/self/ns/cgroup
+  lrwxrwxrwx 1 root root 0 2014-07-15 10:35 /proc/self/ns/cgroup -> cgroup:[4026532183]
+  # From within new cgroupns, process sees that its in the root cgroup
+  [ns]$ cat /proc/self/cgroup
+  0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/
+
+  # From global cgroupns:
+  $ cat /proc/<pid>/cgroup
+  0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/batchjobs/container_id1
+
+  # Unshare cgroupns along with userns and mountns
+  # Following calls unshare(CLONE_NEWCGROUP|CLONE_NEWUSER|CLONE_NEWNS), then
+  # sets up uid/gid map and execs /bin/bash
+  $ ~/unshare -c -u -m
+  # Originally, we were in /batchjobs/container_id1 cgroup. Mount our own cgroup
+  # hierarchy.
+  [ns]$ mount -t cgroup cgroup /tmp/cgroup
+  [ns]$ ls -l /tmp/cgroup
+  total 0
+  -r--r--r-- 1 root root 0 2014-10-13 09:32 cgroup.controllers
+  -r--r--r-- 1 root root 0 2014-10-13 09:32 cgroup.populated
+  -rw-r--r-- 1 root root 0 2014-10-13 09:25 cgroup.procs
+  -rw-r--r-- 1 root root 0 2014-10-13 09:32 cgroup.subtree_control
+
+The cgroupns-root (/batchjobs/container_id1 in above example) becomes the
+filesystem root for the namespace specific cgroupfs mount.
+
+The virtualization of /proc/self/cgroup file combined with restricting
+the view of cgroup hierarchy by namespace-private cgroupfs mount
+should provide a completely isolated cgroup view inside the container.
+
+In its current form, the cgroup namespaces patcheset provides following
+behavior:
+
+(1) The 'cgroupns-root' for a cgroup namespace is the cgroup in which
+    the process calling unshare is running.
+    For ex. if a process in /batchjobs/container_id1 cgroup calls unshare,
+    cgroup /batchjobs/container_id1 becomes the cgroupns-root.
+    For the init_cgroup_ns, this is the real root ('/') cgroup
+    (identified in code as cgrp_dfl_root.cgrp).
+
+(2) The cgroupns-root cgroup does not change even if the namespace
+    creator process later moves to a different cgroup.
+    $ ~/unshare -c # unshare cgroupns in some cgroup
+    [ns]$ cat /proc/self/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/
+    [ns]$ mkdir sub_cgrp_1
+    [ns]$ echo 0 > sub_cgrp_1/cgroup.procs
+    [ns]$ cat /proc/self/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/sub_cgrp_1
+
+(3) Each process gets its CGROUPNS specific view of /proc/<pid>/cgroup
+(a) Processes running inside the cgroup namespace will be able to see
+    cgroup paths (in /proc/self/cgroup) only inside their root cgroup
+    [ns]$ sleep 100000 &  # From within unshared cgroupns
+    [1] 7353
+    [ns]$ echo 7353 > sub_cgrp_1/cgroup.procs
+    [ns]$ cat /proc/7353/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/sub_cgrp_1
+
+(b) From global cgroupns, the real cgroup path will be visible:
+    $ cat /proc/7353/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/batchjobs/container_id1/sub_cgrp_1
+
+(c) From a sibling cgroupns (cgroupns root-ed at a different cgroup), cgroup
+    path relative to its own cgroupns-root will be shown:
+    # ns2's cgroupns-root is at '/batchjobs/container_id2'
+    [ns2]$ cat /proc/7353/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/../container_id2/sub_cgrp_1
+
+    Note that the relative path always starts with '/' to indicate that its
+    relative to the cgroupns-root of the caller.
+
+(4) Processes inside a cgroupns can move in-and-out of the cgroupns-root
+    (if they have proper access to external cgroups).
+    # From inside cgroupns (with cgroupns-root at /batchjobs/container_id1), and
+    # assuming that the global hierarchy is still accessible inside cgroupns:
+    $ cat /proc/7353/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/sub_cgrp_1
+    $ echo 7353 > batchjobs/container_id2/cgroup.procs
+    $ cat /proc/7353/cgroup
+    0:cpuset,cpu,cpuacct,memory,devices,freezer,hugetlb:/../container_id2
+
+    Note that this kind of setup is not encouraged. A task inside cgroupns
+    should only be exposed to its own cgroupns hierarchy. Otherwise it makes
+    the virtualization of /proc/<pid>/cgroup less useful.
+
+(5) Setns to another cgroup namespace is allowed when:
+    (a) the process has CAP_SYS_ADMIN in its current userns
+    (b) the process has CAP_SYS_ADMIN in the target cgroupns' userns
+    No implicit cgroup changes happen with attaching to another cgroupns. It
+    is expected that the somone moves the attaching process under the target
+    cgroupns-root.
+
+(6) When some thread from a multi-threaded process unshares its
+    cgroup-namespace, the new cgroupns gets applied to the entire process (all
+    the threads). For the unified-hierarchy this is expected as it only allows
+    process-level containerization.  For the legacy hierarchies this may be
+    unexpected.  So all the threads in the process will have the same cgroup.
+
+(7) The cgroup namespace is alive as long as there is atleast 1
+    process inside it. When the last process exits, the cgroup
+    namespace is destroyed. The cgroupns-root and the actual cgroups
+    remain though.
+
+(8) Namespace specific cgroup hierarchy can be mounted by a process running
+    inside cgroupns:
+    $ mount -t cgroup -o __DEVEL__sane_behavior cgroup $MOUNT_POINT
+
+    This will mount the unified cgroup hierarchy with cgroupns-root as the
+    filesystem root. The process needs CAP_SYS_ADMIN in its userns and mntns.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/conf.py
+++ linux-xilinx-zynqmp-5.15.0/Documentation/conf.py
@@ -161,7 +161,7 @@
 #
 # This is also used if you do content translation via gettext catalogs.
 # Usually you set "language" from the command line for these cases.
-language = None
+language = 'en'
 
 # There are two options for replacing |today|: either, you set today to some
 # non-false value, then it is used:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/core-api/dma-api.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/core-api/dma-api.rst
@@ -206,6 +206,20 @@
 
 ::
 
+	size_t
+	dma_opt_mapping_size(struct device *dev);
+
+Returns the maximum optimal size of a mapping for the device.
+
+Mapping larger buffers may take much longer in certain scenarios. In
+addition, for high-rate short-lived streaming mappings, the upfront time
+spent on the mapping may account for an appreciable part of the total
+request lifetime. As such, if splitting larger requests incurs no
+significant performance penalty, then device drivers are advised to
+limit total DMA streaming mappings length to the returned value.
+
+::
+
 	bool
 	dma_need_sync(struct device *dev, dma_addr_t dma_addr);
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/dev-tools/gdb-kernel-debugging.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/dev-tools/gdb-kernel-debugging.rst
@@ -39,6 +39,10 @@
   this mode. In this case, you should build the kernel with
   CONFIG_RANDOMIZE_BASE disabled if the architecture supports KASLR.
 
+- Build the gdb scripts (required on kernels v5.1 and above)::
+
+    make scripts_gdb
+
 - Enable the gdb stub of QEMU/KVM, either
 
     - at VM startup time by appending "-s" to the QEMU command line
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/dev-tools/kfence.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/dev-tools/kfence.rst
@@ -41,6 +41,18 @@
 ``CONFIG_KFENCE_SAMPLE_INTERVAL``. Setting ``kfence.sample_interval=0``
 disables KFENCE.
 
+The sample interval controls a timer that sets up KFENCE allocations. By
+default, to keep the real sample interval predictable, the normal timer also
+causes CPU wake-ups when the system is completely idle. This may be undesirable
+on power-constrained systems. The boot parameter ``kfence.deferrable=1``
+instead switches to a "deferrable" timer which does not force CPU wake-ups on
+idle systems, at the risk of unpredictable sample intervals. The default is
+configurable via the Kconfig option ``CONFIG_KFENCE_DEFERRABLE``.
+
+.. warning::
+   The KUnit test suite is very likely to fail when using a deferrable timer
+   since it currently causes very unpredictable sample intervals.
+
 The KFENCE memory pool is of fixed size, and if the pool is exhausted, no
 further KFENCE allocations occur. With ``CONFIG_KFENCE_NUM_OBJECTS`` (default
 255), the number of available guarded objects can be controlled. Each object
@@ -231,10 +243,14 @@
 of the sample interval, the next allocation through the main allocator (SLAB or
 SLUB) returns a guarded allocation from the KFENCE object pool (allocation
 sizes up to PAGE_SIZE are supported). At this point, the timer is reset, and
-the next allocation is set up after the expiration of the interval. To "gate" a
-KFENCE allocation through the main allocator's fast-path without overhead,
-KFENCE relies on static branches via the static keys infrastructure. The static
-branch is toggled to redirect the allocation to KFENCE.
+the next allocation is set up after the expiration of the interval.
+
+When using ``CONFIG_KFENCE_STATIC_KEYS=y``, KFENCE allocations are "gated"
+through the main allocator's fast-path by relying on static branches via the
+static keys infrastructure. The static branch is toggled to redirect the
+allocation to KFENCE. Depending on sample interval, target workloads, and
+system architecture, this may perform better than the simple dynamic branch.
+Careful benchmarking is recommended.
 
 KFENCE objects each reside on a dedicated page, at either the left or right
 page boundaries selected at random. The pages to the left and right of the
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -119,6 +119,9 @@
 - OMAP3 BeagleBoard : Low cost community board
   compatible = "ti,omap3-beagle", "ti,omap3430", "ti,omap3"
 
+- OMAP3 BeagleBoard A to B4 : Early BeagleBoard revisions A to B4 with a timer quirk
+  compatible = "ti,omap3-beagle-ab4", "ti,omap3-beagle", "ti,omap3430", "ti,omap3"
+
 - OMAP3 Tobi with Overo : Commercial expansion board with daughter board
   compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3"
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/arm/qcom.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -135,28 +135,34 @@
           - const: qcom,msm8974
 
       - items:
-          - enum:
-              - alcatel,idol347
-          - const: qcom,msm8916-mtp/1
           - const: qcom,msm8916-mtp
+          - const: qcom,msm8916-mtp/1
           - const: qcom,msm8916
 
       - items:
           - enum:
-              - longcheer,l8150
+              - alcatel,idol347
               - samsung,a3u-eur
               - samsung,a5u-eur
           - const: qcom,msm8916
 
       - items:
+          - const: longcheer,l8150
+          - const: qcom,msm8916-v1-qrd/9-v1
+          - const: qcom,msm8916
+
+      - items:
           - enum:
               - sony,karin_windy
+          - const: qcom,apq8094
+
+      - items:
+          - enum:
               - sony,karin-row
               - sony,satsuki-row
               - sony,sumire-row
               - sony,suzuran-row
-              - qcom,msm8994
-          - const: qcom,apq8094
+          - const: qcom,msm8994
 
       - items:
           - const: qcom,msm8996-mtp
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/arm/xilinx.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/arm/xilinx.yaml
@@ -61,12 +61,6 @@
           - const: xlnx,zynqmp-zc1254
           - const: xlnx,zynqmp
 
-      - description: Xilinx internal board zc1275
-        items:
-          - const: xlnx,zynqmp-zc1275-revA
-          - const: xlnx,zynqmp-zc1275
-          - const: xlnx,zynqmp
-
       - description: Xilinx 96boards compatible board zcu100
         items:
           - const: xlnx,zynqmp-zcu100-revC
@@ -87,6 +81,7 @@
               - xlnx,zynqmp-zcu102-revA
               - xlnx,zynqmp-zcu102-revB
               - xlnx,zynqmp-zcu102-rev1.0
+              - xlnx,zynqmp-zcu102-rev1.1
           - const: xlnx,zynqmp-zcu102
           - const: xlnx,zynqmp
 
@@ -115,6 +110,54 @@
           - const: xlnx,zynqmp-zcu111
           - const: xlnx,zynqmp
 
+      - description: Xilinx evaluation board zcu208
+        items:
+          - enum:
+              - xlnx,zynqmp-zcu208-revA
+              - xlnx,zynqmp-zcu208-rev1.0
+          - const: xlnx,zynqmp-zcu208
+          - const: xlnx,zynqmp
+
+      - description: Xilinx evaluation board zcu216
+        items:
+          - enum:
+              - xlnx,zynqmp-zcu216-revA
+              - xlnx,zynqmp-zcu216-rev1.0
+          - const: xlnx,zynqmp-zcu216
+          - const: xlnx,zynqmp
+
+      - description: Xilinx evaluation board zcu1275
+        items:
+          - enum:
+              - xlnx,zynqmp-zcu1275-revA
+              - xlnx,zynqmp-zcu1275-revB
+              - xlnx,zynqmp-zcu1275-rev1.0
+          - const: xlnx,zynqmp-zcu1275
+          - const: xlnx,zynqmp
+
+      - description: Xilinx evaluation board zcu1285
+        items:
+          - enum:
+              - xlnx,zynqmp-zcu1285-revA
+              - xlnx,zynqmp-zcu1285-rev1.0
+          - const: xlnx,zynqmp-zcu1285
+
+      - description: Xilinx Kria SOMs
+        items:
+          - const: xlnx,zynqmp-sm-k26-rev1
+          - const: xlnx,zynqmp-sm-k26-revB
+          - const: xlnx,zynqmp-sm-k26-revA
+          - const: xlnx,zynqmp-sm-k26
+          - const: xlnx,zynqmp
+
+      - description: Xilinx Kria SOMs (starter)
+        items:
+          - const: xlnx,zynqmp-smk-k26-rev1
+          - const: xlnx,zynqmp-smk-k26-revB
+          - const: xlnx,zynqmp-smk-k26-revA
+          - const: xlnx,zynqmp-smk-k26
+          - const: xlnx,zynqmp
+
 additionalProperties: true
 
 ...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/arm/zynq/zynq-efuse.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/arm/zynq/zynq-efuse.txt
@@ -0,0 +1,15 @@
+Device tree bindings for Zynq's eFuse Controller
+
+The Zynq eFuse controller provides the access to the chip efuses which contain
+information about device DNA, security settings and also device status.
+
+Required properties:
+ compatible: Compatibility string. Must be "xlnx,zynq-efuse".
+ reg: Specify the base and size of the EFUSE controller registers
+      in the memory map. E.g.: reg = <0xf800d000 0x20>;
+
+Example:
+efuse: efuse@f800d000 {
+	compatible = "xlnx,zynq-efuse";
+	reg = <0xf800d000 0x20>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/arm/zynq/zynq-ocmc.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/arm/zynq/zynq-ocmc.txt
@@ -0,0 +1,17 @@
+Device tree bindings for Zynq's OCM Controller
+
+The OCM is divided to 4 64kB segments which can be separately configured
+to low or high location. Location is controlled via SLCR.
+
+Required properties:
+ compatible: Compatibility string. Must be "xlnx,zynq-ocmc-1.0".
+ reg: Specify the base and size of the OCM controller registers
+      in the memory map. E.g.: reg = <0xf800c000 0x1000>;
+
+Example:
+ocmc: ocmc@f800c000 {
+	compatible = "xlnx,zynq-ocmc-1.0";
+	interrupt-parent = <&intc>;
+	interrupts = <0 3 4>;
+	reg = <0xf800c000 0x1000>;
+} ;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml
@@ -0,0 +1,196 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ata/ceva,ahci-1v84.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ceva AHCI SATA Controller
+
+maintainers:
+  - Piyush Mehta <piyush.mehta@xilinx.com>
+
+description: |
+  The Ceva SATA controller mostly conforms to the AHCI interface with some
+  special extensions to add functionality, is a high-performance dual-port
+  SATA host controller with an AHCI compliant command layer which supports
+  advanced features such as native command queuing and frame information
+  structure (FIS) based switching for systems employing port multipliers.
+
+properties:
+  compatible:
+    const: ceva,ahci-1v84
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  dma-coherent: true
+
+  interrupts:
+    maxItems: 1
+
+  iommus:
+    maxItems: 4
+
+  power-domains:
+    maxItems: 1
+
+  ceva,p0-cominit-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMINIT parameter for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>;
+    items:
+      - description: CINMP - COMINIT Negate Minimum Period.
+      - description: CIBGN - COMINIT Burst Gap Nominal.
+      - description: CIBGMX - COMINIT Burst Gap Maximum.
+      - description: CIBGMN - COMINIT Burst Gap Minimum.
+
+  ceva,p0-comwake-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMWAKE parameter for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>;
+    items:
+      - description: CWBGMN - COMWAKE Burst Gap Minimum.
+      - description: CWBGMX - COMWAKE Burst Gap Maximum.
+      - description: CWBGN - COMWAKE Burst Gap Nominal.
+      - description: CWNMP - COMWAKE Negate Minimum Period.
+
+  ceva,p0-burst-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      Burst timing value for COM parameter for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
+    items:
+      - description: BMX - COM Burst Maximum.
+      - description: BNM - COM Burst Nominal.
+      - description: SFD - Signal Failure Detection value.
+      - description: PTST - Partial to Slumber timer value.
+
+  ceva,p0-retry-params:
+    $ref: /schemas/types.yaml#/definitions/uint16-array
+    description: |
+      Retry interval timing value for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-retry-params = /bits/ 16 <RIT RCT>;
+    items:
+      - description: RIT - Retry Interval Timer.
+      - description: RCT - Rate Change Timer.
+
+  ceva,p1-cominit-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMINIT parameter for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,p1-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>;
+    items:
+      - description: CINMP - COMINIT Negate Minimum Period.
+      - description: CIBGN - COMINIT Burst Gap Nominal.
+      - description: CIBGMX - COMINIT Burst Gap Maximum.
+      - description: CIBGMN - COMINIT Burst Gap Minimum.
+
+  ceva,p1-comwake-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMWAKE parameter for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,p1-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>;
+    items:
+      - description: CWBGMN - COMWAKE Burst Gap Minimum.
+      - description: CWBGMX - COMWAKE Burst Gap Maximum.
+      - description: CWBGN - COMWAKE Burst Gap Nominal.
+      - description: CWNMP - COMWAKE Negate Minimum Period.
+
+  ceva,p1-burst-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      Burst timing value for COM parameter for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,p1-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
+    items:
+      - description: BMX - COM Burst Maximum.
+      - description: BNM - COM Burst Nominal.
+      - description: SFD - Signal Failure Detection value.
+      - description: PTST - Partial to Slumber timer value.
+
+  ceva,p1-retry-params:
+    $ref: /schemas/types.yaml#/definitions/uint16-array
+    description: |
+      Retry interval timing value for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,pN-retry-params = /bits/ 16 <RIT RCT>;
+    items:
+      - description: RIT - Retry Interval Timer.
+      - description: RCT - Rate Change Timer.
+
+  ceva,broken-gen2:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: |
+      limit to gen1 speed instead of gen2.
+
+  dma-coherent:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: |
+      Enable this flag if CCI is enabled in design.
+      Adding this flag configures AXI cache control register.
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    items:
+      - const: sata-phy
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+  - ceva,p0-cominit-params
+  - ceva,p0-comwake-params
+  - ceva,p0-burst-params
+  - ceva,p0-retry-params
+  - ceva,p1-cominit-params
+  - ceva,p1-comwake-params
+  - ceva,p1-burst-params
+  - ceva,p1-retry-params
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/power/xlnx-zynqmp-power.h>
+    #include <dt-bindings/reset/xlnx-zynqmp-resets.h>
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+    #include <dt-bindings/phy/phy.h>
+
+    sata: ahci@fd0c0000 {
+        compatible = "ceva,ahci-1v84";
+        reg = <0xfd0c0000 0x200>;
+        interrupt-parent = <&gic>;
+        interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&zynqmp_clk SATA_REF>;
+        ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
+        ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
+        ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
+        ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
+        ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
+        ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
+        ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
+        ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
+        ceva,broken-gen2;
+        dma-coherent;
+        phys = <&psgtr 1 PHY_TYPE_SATA 1 1>;
+        resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/adi,axi-clkgen.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/adi,axi-clkgen.yaml
@@ -26,9 +26,21 @@
     description:
       Specifies the reference clock(s) from which the output frequency is
       derived. This must either reference one clock if only the first clock
-      input is connected or two if both clock inputs are connected.
-    minItems: 1
-    maxItems: 2
+      input is connected or two if both clock inputs are connected. The last
+      clock is the AXI bus clock that needs to be enabled so we can access the
+      core registers.
+    minItems: 2
+    maxItems: 3
+
+  clock-names:
+    oneOf:
+      - items:
+          - const: clkin1
+          - const: s_axi_aclk
+      - items:
+          - const: clkin1
+          - const: clkin2
+          - const: s_axi_aclk
 
   '#clock-cells':
     const: 0
@@ -40,6 +52,7 @@
   - compatible
   - reg
   - clocks
+  - clock-names
   - '#clock-cells'
 
 additionalProperties: false
@@ -50,5 +63,6 @@
       compatible = "adi,axi-clkgen-2.00.a";
       #clock-cells = <0>;
       reg = <0xff000000 0x1000>;
-      clocks = <&osc 1>;
+      clocks = <&osc 1>, <&clkc 15>;
+      clock-names = "clkin1", "s_axi_aclk";
     };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/idt,idt8t49n24x.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/idt,idt8t49n24x.txt
@@ -0,0 +1,156 @@
+Binding for IDT 8T49N24x Universal Frequency Translator
+
+The 8T49N241 has one fractional-feedback PLL that can be used as a
+jitter attenuator and frequency translator. It is equipped with one
+integer and three fractional output dividers, allowing the generation
+of up to four different output frequencies, ranging from 8kHz to 1GHz.
+These frequencies are completely independent of each other, the input
+reference frequencies and the crystal reference frequency. The device
+places virtually no constraints on input to output frequency conversion,
+supporting all FEC rates, including the new revision of ITU-T
+Recommendation G.709 (2009), most with 0ppm conversion error.
+The outputs may select among LVPECL, LVDS, HCSL or LVCMOS output levels.
+
+The driver can read a full register map from the DT, and will use that
+register map to initialize the attached part (via I2C) when the system
+boots. Any configuration not supported by the common clock framework
+must be done via the full register map, including optimized settings.
+
+The 8T49N241 accepts up to two differential or single-ended input clocks
+and a fundamental-mode crystal input. The internal PLL can lock to either
+of the input reference clocks or just to the crystal to behave as a
+frequency synthesizer. The PLL can use the second input for redundant
+backup of the primary input reference, but in this case, both input clock
+references must be related in frequency.
+
+All outputs are currently assumed to be LVDS, unless overridden in the
+full register map in the DT.
+
+==I2C device node==
+
+Required properties:
+- compatible:	shall be one of "idt,idt8t49n241"
+- reg:		i2c device address, shall be one of 0x7C, 0x6C, 0x7D, 0x6D,
+		0x7E, 0x6E, 0x7F, 0x6F.
+- #clock-cells: From common clock bindings: Shall be 1.
+
+- clocks:	from common clock binding; input clock handle. Required.
+- clock-names:	from common clock binding; clock input names, shall be
+		one of "input-clk0", "input-clk1", "input-xtal". Required.
+
+==Mapping between clock specifier and physical pins==
+
+When referencing the provided clock in the DT using phandle and
+clock specifier, the following mapping applies:
+
+8T49N241:
+	0 -- Q0
+	1 -- Q1
+	2 -- Q2
+	3 -- Q3
+
+==Example==
+
+/* Example1: 25MHz input clock (via CLK0) */
+
+ref25: ref25m {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <25000000>;
+};
+
+i2c-master-node {
+
+	/* IDT 8T49N241 i2c universal frequency translator */
+	i2c241: clock-generator@6a {
+		compatible = "idt,idt8t49n241";
+		reg = <0x6c>;
+		#clock-cells = <1>;
+
+		/* Connect input-clk0 to 25MHz reference */
+		clocks = <&ref25m>;
+		clock-names = "input-clk0";
+	};
+};
+
+/* Consumer referencing the 8T49N241 pin Q1 */
+consumer {
+	...
+	clocks = <&i2c241 1>;
+	...
+}
+
+/* Example2: 40MHz xtal frequency, specify all settings */
+
+ref40: ref40m {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <40000000>;
+};
+
+i2c-master-node {
+
+	/* IDT 8T49N241 i2c universal frequency translator */
+	i2c241: clock-generator@6a {
+		compatible = "idt,idt8t49n241";
+		reg = <0x6c>;
+		#clock-cells = <1>;
+
+		/* Connect input-xtal to 40MHz reference */
+		clocks = <&ref40m>;
+		clock-names = "input-xtal";
+
+		settings=[
+09 50 00 60 67 C5 6C FF 03 00 30 00 00 01 00 00
+01 07 00 00 07 00 00 77 6D 06 00 00 00 00 00 FF
+FF FF FF 00 3F 00 2A 00 16 33 33 00 01 00 00 D0
+00 00 00 00 00 00 00 00 00 04 00 00 00 02 00 00
+00 00 00 00 00 00 00 17 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 D7 0A 2B 20 00 00 00 0B
+00 00 00 00 00 00 00 00 00 00 27 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+C3 00 08 01 00 00 00 00 00 00 00 00 00 30 00 00
+00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+00 00 00 00 85 00 00 9C 01 D4 02 71 07 00 00 00
+00 83 00 10 02 08 8C
+];
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/qcom,gcc-msm8996.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/qcom,gcc-msm8996.yaml
@@ -22,16 +22,32 @@
     const: qcom,gcc-msm8996
 
   clocks:
+    minItems: 3
     items:
       - description: XO source
       - description: Second XO source
       - description: Sleep clock source
+      - description: PCIe 0 PIPE clock (optional)
+      - description: PCIe 1 PIPE clock (optional)
+      - description: PCIe 2 PIPE clock (optional)
+      - description: USB3 PIPE clock (optional)
+      - description: UFS RX symbol 0 clock (optional)
+      - description: UFS RX symbol 1 clock (optional)
+      - description: UFS TX symbol 0 clock (optional)
 
   clock-names:
+    minItems: 3
     items:
       - const: cxo
       - const: cxo2
       - const: sleep_clk
+      - const: pcie_0_pipe_clk_src
+      - const: pcie_1_pipe_clk_src
+      - const: pcie_2_pipe_clk_src
+      - const: usb3_phy_pipe_clk_src
+      - const: ufs_rx_symbol_0_clk_src
+      - const: ufs_rx_symbol_1_clk_src
+      - const: ufs_tx_symbol_0_clk_src
 
   '#clock-cells':
     const: 1
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/renesas,versaclock7.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/renesas,versaclock7.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/renesas,versaclock7.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas Versaclock7 Programmable Clock Device Tree Bindings
+
+maintainers:
+  - Alex Helms <alexander.helms.jy@renesas.com>
+
+description: |
+  Renesas Versaclock7 is a family of configurable clock generator and
+  jitter attenuator ICs with fractional and integer dividers.
+
+properties:
+  '#clock-cells':
+    const: 1
+
+  compatible:
+    enum:
+      - renesas,rc21008a
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: External crystal or oscillator
+
+  clock-names:
+    items:
+      - const: xin
+
+required:
+  - '#clock-cells'
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    vc7_xin: vc7_xin {
+        compatible = "fixed-clock";
+        #clock-cells = <0>;
+        clock-frequency = <49152000>;
+    };
+
+    i2c@0 {
+        reg = <0x0 0x100>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        vc7: vc7@9 {
+            compatible = "renesas,rc21008a";
+            reg = <0x9>;
+            #clock-cells = <1>;
+            clocks = <&vc7_xin>;
+            clock-names = "xin";
+        };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/silabs,si5324.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/silabs,si5324.txt
@@ -0,0 +1,78 @@
+Binding for Silicon Labs si5324, si5328 and si5319 programmable
+I2C clock generator.
+
+Reference
+This binding uses the common clock binding[1].
+The si5324 is programmable i2c low-bandwidth, jitter-attenuating, precision
+clock multiplier with up to 2 output clocks. The internal structure can be
+found in [2].
+The internal pin structure of si5328 and si5319 can be found in [3].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Si5324 Data Sheet
+	http://www.silabs.com/Support%20Documents/TechnicalDocs/Si5324.pdf
+[3] Si53xx Reference Manual
+	http://www.silabs.com/Support%20Documents/TechnicalDocs/
+	Si53xxReferenceManual.pdf
+
+==I2C device node==
+
+Required properties:
+- compatible: should be one of
+	"silabs,si5324"
+	"silabs,si5319"
+	"silabs,si5328"
+- reg: i2c device address.
+- #clock-cells: from common clock binding; shall be set to 1.
+- clocks: from common clock binding; list of parent clock
+  handles, clock name should be one of
+	"xtal"
+	"clkin1"
+	"clkin2"
+- #address-cells: shall be set to 1.
+- #size-cells: shall be set to 0.
+
+Optional properties:
+- silabs,pll-source: pair of (number, source) for each pll. Allows
+  to overwrite clock source of pll.
+
+==Child nodes==
+
+Each of the clock outputs can be overwritten individually by
+using a child node to the I2C device node. If a child node for a clock
+output is not set, the eeprom configuration is not overwritten.
+
+Required child node properties:
+- reg: number of clock output.
+- clock-frequency: default output frequency at power on
+
+Optional child node properties:
+- silabs,drive-strength: output drive strength in mA, shall be one of {2,4,6,8}.
+
+Example:
+Following example describes the ZCU102 board with hdmi design which
+uses si5319 as clock generator. XTAL is hard-wired on the board to act
+as input clock with a frequency of 114.285MHz.
+
+refhdmi: refhdmi {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <114285000>;
+};
+
+/* Si5319 i2c clock generator */
+si5319: clock-generator@68 {
+	status = "okay";
+	compatible = "silabs,si5319";
+	reg = <0x68>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	#clock-cells = <1>;
+	clocks = <&refhdmi>;
+	clock-names = "xtal";
+
+	clk0 {
+		reg = <0>;
+		clock-frequency = <27000000>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/clock/xlnx,clocking-wizard.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Xilinx clocking wizard
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+description:
+  The clocking wizard is a soft ip clocking block of Xilinx versal. It
+  reads required input clock frequencies from the devicetree and acts as clock
+  clock output.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,clocking-wizard
+      - xlnx,clocking-wizard-v5.2
+      - xlnx,clocking-wizard-v6.0
+
+
+  reg:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 1
+
+  clocks:
+    items:
+      - description: clock input
+      - description: axi clock
+
+  clock-names:
+    items:
+      - const: clk_in1
+      - const: s_axi_aclk
+
+
+  xlnx,speed-grade:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 3]
+    description:
+      Speed grade of the device. Higher the speed grade faster is the FPGA device.
+
+  xlnx,nr-outputs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 8
+    description:
+      Number of outputs.
+
+required:
+  - compatible
+  - reg
+  - "#clock-cells"
+  - clocks
+  - clock-names
+  - xlnx,speed-grade
+  - xlnx,nr-outputs
+
+additionalProperties: false
+
+examples:
+  - |
+    clock-controller@b0000000  {
+        compatible = "xlnx,clocking-wizard";
+        reg = <0xb0000000 0x10000>;
+        #clock-cells = <1>;
+        xlnx,speed-grade = <1>;
+        xlnx,nr-outputs = <6>;
+        clock-names = "clk_in1", "s_axi_aclk";
+        clocks = <&clkc 15>, <&clkc 15>;
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/xlnx,vcu.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/xlnx,vcu.txt
@@ -0,0 +1,33 @@
+LogicoreIP designed compatible with Xilinx ZYNQ family.
+-------------------------------------------------------
+
+General concept
+---------------
+
+LogicoreIP design to provide the isolation between processing system
+and programmable logic. Also provides the list of register set to configure
+the frequency.
+
+Required properties:
+- compatible: shall be one of:
+	"xlnx,vcu"
+	"xlnx,vcu-logicoreip-1.0"
+- reg : The base offset and size of the VCU_PL_SLCR register space.
+- clocks: phandle for aclk and pll_ref clocksource
+- clock-names: The identification string, "aclk", is always required for
+   the axi clock. "pll_ref" is required for pll.
+
+Optional properties:
+- reset-gpios : The GPIO used to reset the VCU, if available. Need use this
+		reset gpio when in design 'vcu_resetn' is driven by gpio. See
+		Documentation/devicetree/bindings/gpio/gpio.txt for details.
+
+Example:
+
+	xlnx_vcu: vcu@a0040000 {
+		compatible = "xlnx,vcu-logicoreip-1.0";
+		reg = <0x0 0xa0040000 0x0 0x1000>;
+		reset-gpios = <&gpio 0x4e GPIO_ACTIVE_HIGH>;t
+		clocks = <&si570_1>, <&clkc 71>;
+		clock-names = "pll_ref", "aclk";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/xlnx,versal-clk.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/xlnx,versal-clk.yaml
@@ -16,8 +16,6 @@
   reads required input clock frequencies from the devicetree and acts as clock
   provider for all clock consumers of PS clocks.
 
-select: false
-
 properties:
   compatible:
     const: xlnx,versal-clk
@@ -30,13 +28,11 @@
       clocks to the given clock controller.
     items:
       - description: reference clock
-      - description: alternate reference clock
       - description: alternate reference clock for programmable logic
 
   clock-names:
     items:
       - const: ref
-      - const: alt_ref
       - const: pl_alt_ref
 
 required:
@@ -56,8 +52,8 @@
         versal_clk: clock-controller {
           #clock-cells = <1>;
           compatible = "xlnx,versal-clk";
-          clocks = <&ref>, <&alt_ref>, <&pl_alt_ref>;
-          clock-names = "ref", "alt_ref", "pl_alt_ref";
+          clocks = <&ref>, <&pl_alt_ref>;
+          clock-names = "ref", "pl_alt_ref";
         };
       };
     };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/clock/xlnx,versal-wiz.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/clock/xlnx,versal-wiz.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/xlnx,versal-wiz.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Versal clocking wizard
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+description: |
+  The clocking wizard is a soft ip clocking block of Xilinx versal. It
+  reads required input clock frequencies from the devicetree and acts as clock
+  clock output.
+
+select: false
+
+properties:
+  compatible:
+    const: xlnx,clk-wizard-1.0
+
+  "#clock-cells":
+    const: 1
+
+  clocks:
+    description: List of clock specifiers which are external input
+      clocks to the given clock controller.
+    items:
+      - description: clock input
+      - description: axi clock
+
+  clock-names:
+    items:
+      - const: clk_in1
+      - const: s_axi_aclk
+
+required:
+  - compatible
+  - "#clock-cells"
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    clock-generator@40040000 {
+        #clock-cells = <1>;
+        reg = <0x40040000 0x1000>;
+        compatible = "xlnx,clk-wizard-1.0";
+        speed-grade = <1>;
+        clock-names = "clk_in1", "s_axi_aclk";
+        clocks = <&clkc 15>, <&clkc 15>;clock-output-names = "clk_out1", "clk_out2",
+        "clk_out3", "clk_out4", "clk_out5",
+        "clk_out6", "clk_out7";
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/connector/usb-connector.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/connector/usb-connector.yaml
@@ -104,8 +104,7 @@
       - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB
         Type-C Cable and Connector specification, when Power Delivery is not
         supported.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/string
+    $ref: /schemas/types.yaml#/definitions/string
     enum:
       - default
       - 1.5A
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/crypto/zynqmp-rsa.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/crypto/zynqmp-rsa.txt
@@ -0,0 +1,12 @@
+Xilinx ZynqMP RSA hw acceleration support
+
+The zynqmp PS-RSA hw accelerator is used to encrypt/decrypt
+the given user data.
+
+Required properties:
+- compatible:	should contain "xlnx,zynqmp-rsa"
+
+Example:
+	xlnx_rsa: zynqmp_rsa {
+		compatible = "xlnx,zynqmp-rsa";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/crypto/zynqmp-sha.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/crypto/zynqmp-sha.txt
@@ -0,0 +1,12 @@
+Xilinx ZynqMP SHA3(keccak-384) hw acceleration support.
+
+The ZynqMp PS-SHA hw accelerator is used to calculate the
+SHA3(keccak-384) hash value on the given user data.
+
+Required properties:
+- compatible:	should contain "xlnx,zynqmp-keccak-384"
+
+Example:
+	xlnx_keccak_384: sha384 {
+		compatible = "xlnx,zynqmp-keccak-384";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.yaml
@@ -10,6 +10,9 @@
 maintainers:
   - Neil Armstrong <narmstrong@baylibre.com>
 
+allOf:
+  - $ref: /schemas/sound/name-prefix.yaml#
+
 description: |
   The Amlogic Meson Synopsys Designware Integration is composed of
   - A Synopsys DesignWare HDMI Controller IP
@@ -99,6 +102,8 @@
   "#sound-dai-cells":
     const: 0
 
+  sound-name-prefix: true
+
 required:
   - compatible
   - reg
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/amlogic,meson-vpu.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/amlogic,meson-vpu.yaml
@@ -78,6 +78,10 @@
   interrupts:
     maxItems: 1
 
+  amlogic,canvas:
+    description: should point to a canvas provider node
+    $ref: /schemas/types.yaml#/definitions/phandle
+
   power-domains:
     maxItems: 1
     description: phandle to the associated power domain
@@ -106,6 +110,7 @@
   - port@1
   - "#address-cells"
   - "#size-cells"
+  - amlogic,canvas
 
 additionalProperties: false
 
@@ -118,6 +123,7 @@
         interrupts = <3>;
         #address-cells = <1>;
         #size-cells = <0>;
+        amlogic,canvas = <&canvas>;
 
         /* CVBS VDAC output port */
         port@0 {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
@@ -72,8 +72,7 @@
       - const: hpd-removed
 
   ddc:
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/phandle
+    $ref: /schemas/types.yaml#/definitions/phandle
     description: >
       Phandle of the I2C controller used for DDC EDID probing
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
@@ -76,9 +76,8 @@
 
   adi,input-depth:
     description: Number of bits per color component at the input.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - enum: [ 8, 10, 12 ]
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 8, 10, 12 ]
 
   adi,input-colorspace:
     description: Input color space.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
@@ -87,7 +87,7 @@
   adi,dsi-lanes:
     description: Number of DSI data lanes connected to the DSI host.
     $ref: /schemas/types.yaml#/definitions/uint32
-    enum: [ 1, 2, 3, 4 ]
+    enum: [ 2, 3, 4 ]
 
   ports:
     description:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
@@ -26,9 +26,8 @@
   reg-io-width:
     description:
       Width (in bytes) of the registers specified by the reg property.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - enum: [1, 4]
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 4]
     default: 1
 
   clocks:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
@@ -31,7 +31,7 @@
       - description: Display byte clock
       - description: Display byte interface clock
       - description: Display pixel clock
-      - description: Display escape clock
+      - description: Display core clock
       - description: Display AHB clock
       - description: Display AXI clock
 
@@ -64,6 +64,18 @@
       Indicates if the DSI controller is driving a panel which needs
       2 DSI links.
 
+  qcom,master-dsi:
+    type: boolean
+    description: |
+      Indicates if the DSI controller is the master DSI controller when
+      qcom,dual-dsi-mode enabled.
+
+  qcom,sync-dual-dsi:
+    type: boolean
+    description: |
+      Indicates if the DSI controller needs to sync the other DSI controller
+      with MIPI DCS commands when qcom,dual-dsi-mode enabled.
+
   assigned-clocks:
     minItems: 2
     maxItems: 2
@@ -135,8 +147,6 @@
   - phy-names
   - assigned-clocks
   - assigned-clock-parents
-  - power-domains
-  - operating-points-v2
   - ports
 
 additionalProperties: false
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
@@ -39,7 +39,6 @@
   - compatible
   - reg
   - reg-names
-  - vdds-supply
 
 unevaluatedProperties: false
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
@@ -37,7 +37,6 @@
   - compatible
   - reg
   - reg-names
-  - vcca-supply
 
 unevaluatedProperties: false
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
@@ -34,6 +34,10 @@
   vddio-supply:
     description: Phandle to vdd-io regulator device node.
 
+  qcom,dsi-phy-regulator-ldo-mode:
+    type: boolean
+    description: Indicates if the LDO mode PHY regulator is wanted.
+
 required:
   - compatible
   - reg
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/panel/display-timings.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/panel/display-timings.yaml
@@ -31,8 +31,7 @@
 patternProperties:
   "^timing":
     type: object
-    allOf:
-      - $ref: panel-timing.yaml#
+    $ref: panel-timing.yaml#
 
 additionalProperties: false
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/sitronix,st7735r.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/sitronix,st7735r.yaml
@@ -72,6 +72,7 @@
                     dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
                     reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
                     rotation = <270>;
+                    backlight = <&backlight>;
             };
     };
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/ste,mcde.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/ste,mcde.yaml
@@ -58,8 +58,8 @@
   "^dsi@[0-9a-f]+$":
     description: subnodes for the three DSI host adapters
     type: object
-    allOf:
-      - $ref: dsi-controller.yaml#
+    $ref: dsi-controller.yaml#
+
     properties:
       compatible:
         const: ste,mcde-dsi
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/bridge.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/bridge.txt
@@ -0,0 +1,29 @@
+Xilinx DRM bridge
+-----------------
+
+The Xilinx DRM provides the interface layer called Xilinx bridge to bridge
+multiple components with a series of functions. It models a simple
+unidirectional communication, single client -> single bridge. The client
+is not limited to DRM compatible drivers, but can be any subsystem driver,
+but the client driver should call the bridge functions explicitly.
+
+Provider
+--------
+
+The bridge provider should assign a corresponding of_node to struct xlnx_bridge.
+For example, if its own node is used,
+
+	provider_node: provider_node {
+	};
+
+	bridge.of_node = provider_device->of_node;
+
+Client
+------
+
+The bridge client should have a phandle to the bridge device node. The bridge
+device node should be passed to get a bridge instance,
+
+       client_node {
+	       xlnx,bridge = <&provider_node>;
+       };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,dp-tx.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,dp-tx.yaml
@@ -0,0 +1,182 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/xlnx/xlnx,dp-tx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx DisplayPort Transmitter Subsystem
+
+maintainers:
+  - Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>
+
+description: |
+  The Xilinx DisplayPort Tx Subsystem contains several subcores to implement
+  a DisplayPort Transmitter and outputs video data using DisplayPort protocol.
+  For more details, please refer to PG199 at
+  https://www.xilinx.com/support/documentation/ip_documentation/dp_tx_subsystem/v2_1/pg199-displayport-tx-subsystem.pdf
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,v-dp-txss-3.0
+
+  reg:
+    maxItems: 2
+    description: DisplayPort Transmitter Subsystem registers
+
+  reg-names:
+    items:
+      - const: dp_base
+      - const: gt_quad_base
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: List of clock specifiers
+    items:
+      - description: AXI Lite clock
+      - description: Video clock
+
+  clock-names:
+    items:
+      - const: s_axi_aclk
+      - const: tx_vid_clk
+
+  phys:
+    description: This denotes phandles for phy lanes registered
+                 for DP protocol.DisplayPort always require 4 lanes
+
+  phy-names:
+    items:
+      - const: dp-phy0
+      - const: dp-phy1
+      - const: dp-phy2
+      - const: dp-phy3
+
+  xlnx,max-lanes:
+    description: Max number of lanes that IP configured with.
+                 Possible values are 1, 2, 4.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4]
+
+  xlnx,max-link-rate:
+    description: |
+      Max link rate that IP configured with.Possible values are as below -
+      162000 - 1.6 Gb/s
+      270000 - 2.7 Gb/s
+      540000 - 5.4 Gb/s
+      810000 - 8.1 Gb/s
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [162000, 270000, 540000, 810000]
+
+  xlnx,bpc:
+    description: |
+      Max BPC value that IP configured with. For example if IP is configured
+      with 10 BPC means it supports (6, 8, 10) up to 10bpc.
+      Possible values are 6, 8, 10, 12, 16.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [6, 8, 10, 12, 16]
+
+  xlnx,audio-channels:
+    description: |
+      This denotes number of audio channels enabled in the IP
+      configuration. Possible values are 2, 3, 4, 5, 6, 7, 8.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [2, 3, 4, 5, 6, 7, 8]
+
+  xlnx,versal-gt:
+    type: boolean
+    description: |
+      Boolean property present when versal GT is present in design.
+
+  xlnx,xilinx-vfmc:
+    description: phandle of xilinx video FMC node
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+  ports:
+    type: object
+
+    properties:
+      port@0:
+        type: object
+        description: |
+          Output / source port node, endpoint describing modules
+          connected the DisplayPort transmitter
+
+        properties:
+          reg:
+            const: 0
+
+          endpoint:
+            type: object
+
+            properties:
+
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+            additionalProperties: false
+
+        additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+  - xlnx,max-link-rate
+  - xlnx,bpc
+  - xlnx,max-lanes
+  - phy-names
+  - phys
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+   bus {
+       #address-cells = <2>;
+       #size-cells = <2>;
+
+       v_dp_txss1@a0100000 {
+           compatible = "xlnx,v-dp-txss-3.0";
+           reg = <0x0 0xa0100000 0x0 0x40000>, <0x0 0xa4080000 0x0 0x10000>;
+           reg-names = "dp_base", "gt_quad_base";
+           clock-names = "s_axi_aclk", "tx_vid_clk";
+           clocks = <&zynqmp_clk 71>, <&si570_1>;
+           interrupts = <0 92 4>;
+           xlnx,max-lanes = <4>;
+           xlnx,max-link-rate = <810000>;
+           xlnx,bpc = <8>;
+           xlnx,audio-channels = <2>;
+           xlnx,versal-gt;
+           xlnx,xilinx-vfmc = <&xfmc>;
+           phy-names = "dp-phy0", "dp-phy1", "dp-phy2", "dp-phy3";
+           phys = <&vphy_lane0 0 1 1 0>, <&vphy_lane1 0 1 1 0>,
+                  <&vphy_lane2 0 1 1 0>, <&vphy_lane3 0 1 1 0>;
+
+           ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                   reg = <0>;
+                   dp_transmitter: endpoint {
+                       remote-endpoint = <&display_controller>;
+                   };
+               };
+           };
+       };
+   };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,dsi.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,dsi.txt
@@ -0,0 +1,74 @@
+Device-Tree bindings for Xilinx MIPI DSI Tx IP core
+
+The IP core supports transmission of video data in MIPI DSI protocol.
+
+Required properties:
+ - compatible: Should be "xlnx,dsi".
+
+ - reg: Base address and size of the IP core.
+
+ - xlnx,dsi-datatype: Color format. The value should be one of "MIPI_DSI_FMT_RGB888",
+  "MIPI_DSI_FMT_RGB666", "MIPI_DSI_FMT_RGB666_PACKED" or "MIPI_DSI_FMT_RGB565".
+
+ - simple_panel: The subnode for connected panel. This represents the
+   DSI peripheral connected to the DSI host node. Please refer to
+   Documentation/devicetree/bindings/display/mipi-dsi-bus.txt. The
+   simple-panel driver has auo,b101uan01 panel timing parameters added along
+   with other existing panels. DSI driver derive the required Tx IP controller
+   timing values from the panel timing parameters.
+
+ - port: Logical block can be used / connected independently with
+   external device. In the display controller port nodes, topology
+   for entire pipeline should be described using the DT bindings defined in
+   Documentation/devicetree/bindings/graph.txt.
+
+ - xlnx,dsi-num-lanes: Possible number of DSI lanes for the Tx controller.
+   The values should be 1, 2, 3 or 4. Based on xlnx,dsi-num-lanes and
+   line rate for the MIPI D-PHY core in Mbps, the AXI4-stream received by
+   Xilinx MIPI DSI Tx IP core adds markers as per DSI protocol and the packet
+   thus framed is convered to serial data by MIPI D-PHY core. Please refer
+   Xilinx pg238 for more details. This value should be equal to the number
+   of lanes supported by the connected DSI panel. Panel has to support this
+   value or has to be programmed to the same value that DSI Tx controller is
+   configured to.
+
+ - clocks: List of phandles to Video and 200Mhz DPHY clocks.
+
+ - clock-names: Must contain "s_axis_aclk" and "dphy_clk_200M" in same order as
+   clocks listed in clocks property.
+
+Required simple_panel properties:
+ - compatible: Value should be one of the panel names in
+   Documentation/devicetree/bindings/display/panel/. e.g. "auo,b101uan01".
+   For available panel compatible strings, please refer to bindings in
+   Documentation/devicetree/bindings/display/panel/
+
+Optional properties:
+ - xlnx,vpss: vpss phandle
+   This handle is required only when VPSS is connected to DSI as bridge.
+ - xlnx,dsi-cmd-mode: denotes command mode enable.
+
+Example:
+
+#include <dt-bindings/drm/mipi-dsi.h>
+	mipi_dsi_tx_subsystem@80000000 {
+		compatible = "xlnx,dsi";
+		reg = <0x0 0x80000000 0x0 0x10000>;
+		xlnx,dsi-num-lanes = <4>;
+		xlnx,dsi-data-type = <MIPI_DSI_FMT_RGB888>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		xlnx,vpss = <&v_proc_ss_0>;
+		clock-names = "dphy_clk_200M", "s_axis_aclk";
+		clocks = <&misc_clk_0>, <&misc_clk_1>;
+		encoder_dsi_port: port@0 {
+			reg = <0>;
+			dsi_encoder: endpoint {
+				remote-endpoint = <&xyz_port>;
+			};
+		};
+		simple_panel: simple-panel@0 {
+			compatible = "auo,b101uan01";
+			reg = <0>;
+			};
+		};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,mixer.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,mixer.txt
@@ -0,0 +1,211 @@
+Device-Tree bindings for Xilinx Video Mixer IP core
+
+The IP core provides a flexible video processing block for alpha blending
+and compositing multiple video and/or graphics layers.
+Support for up to sixteen layers based on IP version, with an optional logo
+layer, using a combination of video inputs from either frame buffer or
+streaming video cores (through AXI4-Stream interfaces) is provided.
+The Video Mixer always has one streaming input layer, known as master layer.
+
+Required properties:
+ - compatible: Must contain atleast one of
+	"xlnx,mixer-5.0" (MIXER 5.0 version)
+	"xlnx,mixer-4.0" (MIXER 4.0 version)
+	"xlnx,mixer-3.0" (MIXER 3.0 version)
+ - reg: Base address and size of the IP core.
+ - interrupts: Interrupt number.
+ - interrupts-parent: phandle for interrupt controller.
+ - reset-gpio: gpio to reset the mixer IP
+ - xlnx,enable-csc-coefficient-register: denotes colorimetry
+   coefficients can be programmed, valid for mixer 5.0 version only.
+ - xlnx,dma-addr-width: dma address width, valid values are 32 and 64
+ - xlnx,bpc: bits per component for mixer
+ - xlnx,ppc: pixel per clock for mixer
+ - xlnx,num-layers: Total number of layers (excluding logo)
+   Value ranges from 1-9 for compatible string xlnx,mixer-3.0 and
+   Value ranges from 1-17 for comptaible string xlnx,mixer-4.0 and above
+ - layer_[x]: node for [x] layer
+ - xlnx,layer-id: layer identifier number
+ - xlnx,vformat: video format for layer. See list of supported formats below.
+ - xlnx,layer-max-width: max layer width, mandatory for master layer
+   for overlay layers if scaling is alowed then this is mandatory otherwise
+   not required for overlay layers. Valid range is 64 to 8192
+ - xlnx,layer-max-height: max layer height, mandatory for master layer
+   Not required for overlay layers. Valid range is 64 to 4320
+ - xlnx,layer-primary: denotes the primary layer, should be mentioned in node
+   of layer which is expected to be constructing the primary plane
+
+Optional properties:
+ - dmas: dma attach to layer, mandatory for master layer
+   for rest other layers its optional
+ - dma-names: Should be "dma0", for more details on DMA identifier string
+   refer Documentation/devicetree/bindings/dma/dma.txt
+ - xlnx,layer-streaming: denotes layer can be streaming,
+   mandatory for master layer. Streaming layers need external dma, where
+   as non streaming layers read directly from memory.
+ - xlnx,layer-alpha: denotes layer can do alpha compositing
+ - xlnx,layer-scale: denotes layer can be scale to 2x and 4x
+ - xlnx,logo-layer: denotes logo layer is enable
+ - logo: logo layer
+ - xlnx,bridge: phandle to bridge node.
+   This handle is required only when VTC is connected as bridge.
+ - memory-region: phandle to /reserved-memory node.
+   If memory is reserved for special use by mixer then this node
+   can be used to refer and use from this reserved memory region.
+
+Supported Formats:
+	Mixer IP Format		Driver supported Format String
+	 BGR888			"RG24"
+	 RGB888			"BG24"
+	 XBGR2101010		"XB30"
+	 XRGB8888		"XR24"
+	 RGBA8888		"RA24"
+	 ABGR8888		"AB24"
+	 ARGB8888		"AR24"
+	 XBGR8888		"XB24"
+	 YUYV			"YUYV"
+	 UYVY			"UYVY"
+	 AYUV			"AYUV"
+	 NV12			"NV12"
+	 NV16			"NV16"
+	 Y8			"GREY"
+	 Y10			"Y10 " (Note: Space included)
+	 XVUY2101010		"XV30"
+	 VUY888			"VU24"
+	 XVUY8888		"XV24"
+	 XV15			"XV15"
+	 XV20			"XV20"
+Note : Format strings are case sensitive.
+
+Example:
+	v_mix_0: v_mix@80100000 {
+		compatible = "xlnx,mixer-3.0";
+		interrupt-parent = <&gic>;
+		interrupts = <0 93 4>;
+		reg = <0x0 0x80100000 0x0 0x80000>;
+
+		xlnx,dma-addr-width=<32>;
+		reset-gpios = <&gpio 1 1>;
+
+		xlnx,bpc = <8>;
+		xlnx,ppc = <2>;
+		xlnx,num-layers = <8>;
+		xlnx,logo-layer;
+		xlnx,bridge = <&v_tc_0>;
+
+		mixer_port: mixer_port@0 {
+			reg = <0>;
+			mixer_crtc: endpoint {
+				remote-endpoint = <&sdi_encoder>;
+			};
+		};
+		xv_mix_master: layer_0 {
+			xlnx,layer-id = <0>;
+			xlnx,vformat = "YUYV";
+			xlnx,layer-max-width = <4096>;
+			xlnx,layer-height = <2160>;
+			dmas = <&axi_vdma_0 0>;
+			dma-names = "dma0";
+			xlnx,layer-streaming;
+			xlnx,layer-primary;
+		};
+		xv_mix_overlay_1: layer_1 {
+			xlnx,layer-id = <1>;
+			xlnx,vformat = "NV16";
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+		};
+		xv_mix_overlay_2: layer_2 {
+			xlnx,layer-id = <2>;
+			xlnx,vformat = "YUYV";
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+		};
+		xv_mix_overlay_3: layer_3 {
+			xlnx,layer-id = <3>;
+			xlnx,vformat = "AYUV";
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+		};
+		xv_mix_overlay_4: layer_4 {
+			xlnx,layer-id = <4>;
+			xlnx,vformat = "GREY";
+			dmas = <&scaler_v_frmbuf_rd_0 0>;
+			dma-names = "dma0";
+			xlnx,layer-streaming;
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+		};
+		xv_mix_overlay_5: layer_5 {
+			xlnx,layer-id = <5>;
+			xlnx,vformat = "AB24";
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+		};
+		xv_mix_overlay_6: layer_6 {
+			xlnx,layer-id = <6>;
+			xlnx,vformat = "XB24";
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+			};
+		xv_mix_overlay_7: layer_7 {
+			xlnx,layer-id = <7>;
+			xlnx,vformat = "BG24";
+			xlnx,layer-alpha;
+			xlnx,layer-scale;
+			xlnx,layer-max-width=<1920>;
+		};
+		xv_mix_logo: logo {
+			xlnx,layer-id = <8>;
+			xlnx,logo-height = <64>;
+			xlnx,logo-width = <64>;
+		};
+	};
+Example using reserved memory:
+Reserving from 32bit Shared CMA pool of 512MiB using System RAM:
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+/ {
+	reserved-memory {
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		ranges;
+		psmem_multimedia: multimedia_cma_mem_region {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x40000000 0x00 0x20000000>;
+			reusable;
+		};
+	};
+};
+...
+	v_mix_0: v_mix@80100000 {
+		/* ... */
+		memory-region = <&psmem_multimedia>;
+	};
+
+Reserving from 64bit Shared DMA pool of 1792 MiB using external PL based
+DDR memory:
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+/ {
+	reserved-memory {
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		ranges;
+		plmem_multimedia: multimedia_dma_mem_region {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x48 0x0 0x0 0x70000000>;
+		};
+	};
+
+};
+...
+	v_mix_0: v_mix@80100000 {
+		/* ... */
+		memory-region = <&plmem_multimedia>;
+	}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,pl-disp.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,pl-disp.txt
@@ -0,0 +1,41 @@
+Xilinx PL Display driver
+------------------------
+
+Pl_Display is a logical device to provide completeness to xilinx display
+pipeline. This is a software driver for providing drm components crtc
+and plane for various IPs using xilinx display pipelines.
+
+A linear pipeline with multiple blocks:
+DMA --> PL_Display --> SDI
+
+Required properties:
+
+- compatible: Must be "xlnx,pl-disp"
+- dmas: dma attach to pipeline
+- dma-names: names for dma
+- xlnx,vformat: video format for layer
+- port: Logical block can be used / connected independently with
+  external device. In the display controller port nodes, topology
+  for entire pipeline should be described using the DT bindings defined in
+  Documentation/devicetree/bindings/graph.txt.
+- reg: Base address and size of device
+
+Optional properties:
+ - xlnx,bridge: bridge phandle
+   This handle is required only when VTC is connected as bridge.
+
+Example:
+
+	drm-pl-disp-drv {
+		compatible = "xlnx,pl-disp";
+		dmas = <&axi_vdma_0 0>;
+		dma-names = "dma0";
+		xlnx,vformat = "YUYV";
+		xlnx,bridge = <&v_tc_0>;
+		pl_disp_port@0 {
+			reg = <0>;
+			endpoint {
+				remote-endpoint = <&sdi_port>;
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,sdi-tx.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,sdi-tx.txt
@@ -0,0 +1,63 @@
+Device-Tree bindings for Xilinx SDI Tx subsystem
+
+The IP core supports transmission of video data in SDI Tx protocol
+
+Required properties:
+ - compatible: Should be "xlnx,sdi-tx".
+ - interrupts: Interrupt number.
+ - interrupts-parent: phandle for interrupt controller.
+ - reg: Base address and size of the IP core.
+ - port: Logical block can be used / connected independently with
+   external device. In the display controller port nodes, topology
+   for entire pipeline should be described using the DT bindings defined in
+   Documentation/devicetree/bindings/graph.txt.
+   Minimum one port is required. At max, 2 ports are present.
+   The reg index for AXI4 stream port is 0 and for ancillary data is 1.
+ - clocks: List of phandles to AXI Lite, Video and SDI Tx Clock
+ - clock-names: Must contain "s_axi_aclk", "video_in_clk" and "sdi_tx_clk"
+   in same order as clocks listed in clocks property.
+ - phy-reset-gpio: Specifier for a gpio that asserts GT phy
+
+Optional properties:
+ - xlnx,vpss: vpss phandle
+   This handle is required only when VPSS is connected to SDI as bridge.
+ - xlnx,tx-insert-c-str-st352: Insert ST352 payload in Chroma stream.
+ - interrupt-names: Should be "sdi_tx_irq". This is only required when
+   multiple interrupts are connected in the hardware design.
+ - xlnx,qpll1enabled: boolean property present when the QPLL1 drives GT clock
+   absent with QPLL0 drives GT clock
+- xlnx,picxo_enabled: boolean property present when PICXO is present in design
+
+Example:
+
+	sdi_tx_subsystem@80000000 {
+		compatible = "xlnx,sdi-tx";
+		reg = <0x0 0x80000000 0x0 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 90 4>;
+		interrupt-names = "sdi_tx_irq";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		xlnx,vpss = <&v_proc_ss_0>;
+		clock-names = "s_axi_aclk", "video_in_clk", "sdi_tx_clk";
+		clocks = <&misc_clk_0>, <&misc_clk_1>, <&misc_clk_2>;
+		phy-reset-gpio = <&axi_gpio_0 0 0 0>;
+		xlnx,qpll1enabled;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			encoder_sdi_port: port@0 {
+				reg = <0>;
+				sdi_encoder: endpoint {
+					remote-endpoint = <&pl_disp_crtc>;
+				};
+			};
+
+			sdi_audio_port: port@1 {
+				reg = <1>;
+				sdi_audio_sink_port: endpoint {
+					remote-endpoint = <&sditx_audio_embed_src_port>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,v-hdmi-txss1.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,v-hdmi-txss1.yaml
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/xlnx/xlnx,v-hdmi-txss1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx HDMI Transmitter Subsystem
+
+maintainers:
+  - Venkateshwar Rao Gannavarapu <venkateshwar.rao.gannavarapu@xilinx.com>
+
+description: |
+  The Xilinx HDMI Tx Subsystem contains several subcores to implement
+  a HDMI Transmitter and outputs video data using HDMI protocol.
+  For more details refer to PG350 Xilinx HDMI-2.1 Tx Subsystem.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,v-hdmi-txss1-1.1
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: List of clock specifiers
+    items:
+      - description: AXI Lite CPU clock
+      - description: Link clock
+      - description: Video clock
+      - description: Fixed Rate Link clock
+      - description: AXI4-Stream Video clock
+
+  clock-names:
+    items:
+      - const: s_axi_cpu_aclk
+      - const: link_clk
+      - const: video_clk
+      - const: frl_clk
+      - const: s_axis_video_aclk
+
+  phys:
+    description: This denotes phandles for phy lanes registered
+                 for HDMI protocol. HDMI always require 4 lanes
+
+  phy-names:
+    items:
+      - const: hdmi-phy0
+      - const: hdmi-phy1
+      - const: hdmi-phy2
+      - const: hdmi-phy3
+
+  xlnx,input-pixels-per-clock:
+    description: Configurable samples per clock.
+                 Possible values are 4, 8.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [4, 8]
+
+  xlnx,max-bits-per-component:
+    description: |
+      Max BPC value that IP configured with. For example if IP is configured
+      with 12 BPC means it supports (8, 10, 12) up to 12bpc.
+      Possible values are 8, 10, 12, 16.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [8, 10, 12, 16]
+
+  xlnx,vid-interface:
+    description: Supported video interface.
+                 Possible values are 0 for AXI4-Stream,
+                 1 for Native and 2 for Native-IDE interface.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1, 2]
+
+  xlnx,max-frl-rate:
+    description: Maximum FRL Rate.
+                 Possible values are 0 for TMDS mode,
+                 1 to 6 for FRL mode of operation.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1, 2, 3, 4, 5, 6]
+
+  ports:
+    type: object
+
+    properties:
+      port@0:
+        type: object
+        description: |
+          Output / source port node, endpoint describing modules
+          connected the HDMI transmitter
+
+        properties:
+          reg:
+            const: 0
+
+          endpoint:
+            type: object
+
+            properties:
+
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - xlnx,input-pixels-per-clock
+  - xlnx,max-bits-per-component
+  - xlnx,vid-interface
+  - xlnx,max-frl-rate
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    v_hdmi_txss1@80020000 {
+        compatible = "xlnx,v-hdmi-txss1-1.1";
+        reg = <0x80020000 0x20000>;
+        interrupts = <0 91 4>;
+        clock-names = "s_axi_cpu_aclk", "link_clk", "video_clk", "frl_clk", "s_axis_video_aclk";
+        clocks = <&zynqmp_clk 71>, <&misc_clk_1>, <&misc_clk_3>, <&misc_clk_4>, <&misc_clk_5>;
+        xlnx,input-pixels-per-clock = <4>;
+        xlnx,max-bits-per-component = <0x8>;
+        xlnx,vid-interface = <0>;
+        xlnx,max-frl-rate = <0x6>;
+        phy-names = "hdmi-phy0", "hdmi-phy1", "hdmi-phy2", "hdmi-phy3";
+        phys = <&hdmiphy_lane0 0 1 1 1>, <&hdmiphy_lane1 0 1 1 1>,
+               <&hdmiphy_lane2 0 1 1 1>, <&hdmiphy_lane3 0 1 1 1>;
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                hdmi_encoder: endpoint {
+                    remote-endpoint = <&dmaengine_crtc>;
+                };
+            };
+        };
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,vpss-csc.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,vpss-csc.txt
@@ -0,0 +1,35 @@
+Xllinx VPSS Color Space Converter
+-----------------------------------------
+The Xilinx VPSS Color Space Converter is a Video IP that supports
+color space conversion from RGB to YUV 444/422/420 and vice versa.
+
+Required properties:
+
+- compatible: Must be "xlnx,vpss-csc".
+
+- reg: Physical base address and length of registers set for the device.
+
+- xlnx,video-width: This property qualifies the video format with sample
+  width expressed as a number of bits per pixel component. Supported video
+  width values are 8/10/12/16.
+
+-reset-gpios: GPIO specifier to assert/de-assert the reset line.
+
+- clocks: phandle to IP clock.
+
+- xlnx,max-width: Maximum number of pixels in a line.
+  Valid range from 64 to 8192.
+
+- xlnx,max-height: Maximum number of lines in a frame.
+  Valid range from 64 to 4320.
+
+Example:
+	csc@a0040000 {
+		compatible = "xlnx,vpss-csc";
+		reg = <0x0 0xa0040000 0x0 0x10000>;
+		reset-gpios = <&gpio 0x0 GPIO_ACTIVE_LOW>;
+		xlnx,video-width = <8>;
+		clocks = <&misc_clk_0>;
+		xlnx,max-width = <3840>;
+		xlnx,max-height = <2160>;
+	}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,vpss-scaler.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,vpss-scaler.txt
@@ -0,0 +1,50 @@
+Xilinx VPSS Scaler
+------------------
+The Xilinx VPSS Scaler is a Video IP that supports up scaling,
+down scaling and no scaling functionailty. This supports custom
+resolution values between 0 to 4096.
+
+Required properties:
+
+- compatible: Must be "xlnx,vpss-scaler-2.2" or "xlnx,vpss-scaler".
+
+- reg: Physical base address and length of registers set for the device.
+
+- xlnx,num-hori-taps: The number of horizontal taps for scaling filter
+  supported tap values are 2/4/6/8/10/12.
+
+- xlnx,num-vert-taps: The number of vertical taps for scaling filter
+  supported tap values are 2/4/6/8/10/12.
+
+  A value of 2 represents bilinear filters. A value of 4 represents bicubic.
+  Values 6, 8, 10, 12 represent polyphase filters.
+
+- xlnx,pix-per-clk : The pixels per clock property of the IP.
+  supported values are 1 and 2.
+
+- reset-gpios: GPIO specifier to assert/de-assert the reset line.
+
+- clocks: List of phandles to AXI Lite and Video clock
+
+- clock-names: Must contain "aclk_ctrl" and "aclk_axis" in same order as clocks
+  listed in clocks property.
+
+- xlnx,max-width: Maximum number of pixels in a line.
+  Valid range from 64 to 8192.
+
+- xlnx,max-height: Maximum number of lines in a frame.
+  Valid range from 64 to 4320.
+
+Example:
+	scaler@a0040000 {
+		compatible = "xlnx,vpss-scaler";
+		reg = <0x0 0xa0000000 0x0 0x40000>;
+		reset-gpios = <&gpio 0x0 GPIO_ACTIVE_LOW>;
+		xlnx,num-hori-taps = <8>;
+		xlnx,num-vert-taps = <8>;
+		xlnx,pix-per-clk = <2>;
+		clock-names = "aclk_ctrl", "aclk_axis";
+		clocks = <&misc_clk_0>, <&misc_clk_1>;
+		xlnx,max-width = <3840>;
+		xlnx,max-height = <2160>;
+	}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,vtc.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,vtc.txt
@@ -0,0 +1,32 @@
+Device-Tree bindings for Xilinx Video Timing Controller(VTC)
+
+Xilinx VTC is a general purpose video timing generator and detector.
+The input side of this core automatically detects horizontal and
+vertical synchronization, pulses, polarity, blanking timing and active pixels.
+While on the output, it generates the horizontal and vertical blanking and
+synchronization pulses used with a standard video system including support
+for programmable pulse polarity.
+
+The core is commonly used with Video in to AXI4-Stream core to detect the
+format and timing of incoming video data or with AXI4-Stream to Video out core
+to generate outgoing video timing for downstream sinks like a video monitor.
+
+For details please refer to
+https://www.xilinx.com/support/documentation/ip_documentation/v_tc/v6_1/pg016_v_tc.pdf
+
+Required properties:
+ - compatible: value should be "xlnx,bridge-v-tc-6.1"
+ - reg: base address and size of the VTC IP
+ - xlnx,pixels-per-clock: Pixels per clock of the stream. Can be 1, 2 or 4.
+ - clocks: List of phandles for AXI Lite and Video Clock
+ - clock-names: Must contain "s_axi_aclk" and "clk" in same order as clocks listed
+   in clocks property.
+
+Example:
+	v_tc_0: v_tc@80030000 {
+			compatible = "xlnx,bridge-v-tc-6.1";
+			reg = <0x0 0x80030000 0x0 0x10000>;
+			xlnx,pixels-per-clock = <2>;
+			clock-names = "s_axi_aclk", "clk";
+			clocks = <&misc_clk_0>, <&misc_clk_1>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
@@ -0,0 +1,82 @@
+Xilinx ZynqMP DisplayPort subsystem
+-----------------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,zynqmp-dpsub-1.7".
+
+- reg: Physical base address and length of the registers set for the device.
+- reg-names: Must be "dp", "blend", "av_buf", and "aud" to map logical register
+  partitions.
+
+- interrupts: Interrupt number.
+- interrupts-parent: phandle for interrupt controller.
+
+- clocks: phandles for axi, audio, non-live video, and live video clocks.
+  axi clock is required. Audio clock is optional. If not present, audio will
+  be disabled. One of non-live or live video clock should be present.
+- clock-names: The identification strings are required. "aclk" for axi clock.
+  "dp_aud_clk" for audio clock. "dp_vtc_pixel_clk_in" for non-live video clock.
+  "dp_live_video_in_clk" for live video clock (clock from programmable logic).
+
+- phys: phandles for phy specifier. The number of lanes is configurable
+  between 1 and 2. The number of phandles should be 1 or 2.
+- phy-names: The identifier strings. "dp-phy" followed by index, 0 or 1.
+  For single lane, only "dp-phy0" is required. For dual lane, both "dp-phy0"
+  and "dp-phy1" are required where "dp-phy0" is the primary lane.
+
+- power-domains: phandle for the corresponding power domain
+
+- vid-layer, gfx-layer: Required to represent available layers
+
+Required layer properties
+
+- dmas: phandles for DMA channels as defined in
+  Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names: The identifier strings are required. "gfx0" for graphics layer
+  dma channel. "vid" followed by index (0 - 2) for video layer dma channels.
+
+Optional child node
+
+- The driver populates any child device node in this node. This can be used,
+  for example, to populate the sound device from the DisplayPort subsystem
+  driver.
+
+Example:
+	zynqmp-display-subsystem@fd4a0000 {
+		compatible = "xlnx,zynqmp-dpsub-1.7";
+		reg = <0x0 0xfd4a0000 0x0 0x1000>,
+		      <0x0 0xfd4aa000 0x0 0x1000>,
+		      <0x0 0xfd4ab000 0x0 0x1000>,
+		      <0x0 0xfd4ac000 0x0 0x1000>;
+		reg-names = "dp", "blend", "av_buf", "aud";
+		interrupts = <0 119 4>;
+		interrupt-parent = <&gic>;
+
+		clock-names = "dp_apb_clk", "dp_aud_clk", "dp_live_video_in_clk";
+		clocks = <&dp_aclk>, <&clkc 17>, <&si570_1>;
+
+		phys = <&lane1>, <&lane0>;
+		phy-names = "dp-phy0", "dp-phy1";
+
+		power-domains = <&pd_dp>;
+
+		vid-layer {
+			dma-names = "vid0", "vid1", "vid2";
+			dmas = <&xlnx_dpdma 0>,
+			       <&xlnx_dpdma 1>,
+			       <&xlnx_dpdma 2>;
+		};
+
+		gfx-layer {
+			dma-names = "gfx0";
+			dmas = <&xlnx_dpdma 3>;
+		};
+
+		dma-names = "vid0", "vid1", "vid2", "gfx0";
+		dmas = <&xlnx_dpdma 0>,
+		       <&xlnx_dpdma 1>,
+		       <&xlnx_dpdma 2>,
+		       <&xlnx_dpdma 3>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.yaml
@@ -49,13 +49,19 @@
     const: xlnx,zynqmp-dpsub-1.7
 
   reg:
-    maxItems: 4
+    maxItems: 3
   reg-names:
     items:
       - const: dp
       - const: blend
       - const: av_buf
-      - const: aud
+
+  xlnx,dpaud-reg:
+    description:
+      A phandle to a syscon device, used to access
+      dp audio cfg registers.
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+    maxItems: 1
 
   interrupts:
     maxItems: 1
@@ -121,6 +127,7 @@
   - compatible
   - reg
   - reg-names
+  - xlnx,dpaud-reg
   - interrupts
   - clocks
   - clock-names
@@ -142,9 +149,9 @@
         compatible = "xlnx,zynqmp-dpsub-1.7";
         reg = <0xfd4a0000 0x1000>,
               <0xfd4aa000 0x1000>,
-              <0xfd4ab000 0x1000>,
-              <0xfd4ac000 0x1000>;
-        reg-names = "dp", "blend", "av_buf", "aud";
+              <0xfd4ab000 0x1000>;
+        reg-names = "dp", "blend", "av_buf";
+        xlnx,dpaud-reg = <&dp_aud>;
         interrupts = <0 119 4>;
         interrupt-parent = <&gic>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml
@@ -64,7 +64,7 @@
 then:
   properties:
     clocks:
-      maxItems: 2
+      minItems: 2
 
   required:
     - clock-names
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/moxa,moxart-dma.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/moxa,moxart-dma.txt
@@ -34,8 +34,8 @@
 Use specific request line passing from dma
 For example, MMC request line is 5
 
-	sdhci: sdhci@98e00000 {
-		compatible = "moxa,moxart-sdhci";
+	mmc: mmc@98e00000 {
+		compatible = "moxa,moxart-mmc";
 		reg = <0x98e00000 0x5C>;
 		interrupts = <5 0>;
 		clocks = <&clk_apb>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/xilinx/axi-dma.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/xilinx/axi-dma.txt
@@ -0,0 +1,38 @@
+* Xilinx AXI DMA Test client
+
+Required properties:
+- compatible: Should be "xlnx,axi-dma-test-1.00.a"
+- dmas: a list of <[DMA device phandle] [Channel ID]> pairs,
+	where Channel ID is '0' for write/tx and '1' for read/rx
+	channel.
+- dma-names: a list of DMA channel names, one per "dmas" entry
+
+Example:
+++++++++
+
+dmatest_0: dmatest@0 {
+	compatible ="xlnx,axi-dma-test-1.00.a";
+	dmas = <&axi_dma_0 0
+		&axi_dma_0 1>;
+	dma-names = "axidma0", "axidma1";
+} ;
+
+
+Xilinx AXI DMA Device Node Example
+++++++++++++++++++++++++++++++++++++
+
+axi_dma_0: axidma@40400000 {
+	compatible = "xlnx,axi-dma-1.00.a";
+	#dma-cells = <1>;
+	reg = < 0x40400000 0x10000 >;
+	dma-channel@40400000 {
+		compatible = "xlnx,axi-dma-mm2s-channel";
+		interrupts = < 0 59 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+	dma-channel@40400030 {
+		compatible = "xlnx,axi-dma-s2mm-channel";
+		interrupts = < 0 58 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+} ;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/xilinx/vdmatest.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/xilinx/vdmatest.txt
@@ -0,0 +1,39 @@
+* Xilinx Video DMA Test client
+
+Required properties:
+- compatible: Should be "xlnx,axi-vdma-test-1.00.a"
+- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
+	where Channel ID is '0' for write/tx and '1' for read/rx
+	channel.
+- dma-names: a list of DMA channel names, one per "dmas" entry
+- xlnx,num-fstores: Should be the number of framebuffers as configured in
+	VDMA device node.
+
+Example:
+++++++++
+
+vdmatest_0: vdmatest@0 {
+	compatible ="xlnx,axi-vdma-test-1.00.a";
+	dmas = <&axi_vdma_0 0
+		&axi_vdma_0 1>;
+	dma-names = "vdma0", "vdma1";
+	xlnx,num-fstores = <0x8>;
+} ;
+
+
+Xilinx Video DMA Device Node Example
+++++++++++++++++++++++++++++++++++++
+axi_vdma_0: axivdma@44A40000 {
+	compatible = "xlnx,axi-vdma-1.00.a";
+	...
+	dma-channel@44A40000 {
+		...
+		xlnx,num-fstores = <0x8>;
+		...
+	} ;
+	dma-channel@44A40030 {
+		...
+		xlnx,num-fstores = <0x8>;
+		...
+	} ;
+} ;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
@@ -110,7 +110,11 @@
 Required properties:
 - dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
 	where Channel ID is '0' for write/tx and '1' for read/rx
-	channel.
+	channel. For MCMDA, MM2S channel(write/tx) ID start from
+	'0' and is in [0-15] range. S2MM channel(read/rx) ID start
+	from '16' and is in [16-31] range. These channels ID are
+	fixed irrespective of IP configuration.
+
 - dma-names: a list of DMA channel names, one per "dmas" entry
 
 Example:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/xilinx/xilinx_frmbuf.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/xilinx/xilinx_frmbuf.txt
@@ -0,0 +1,128 @@
+The Xilinx framebuffer DMA engine supports two soft IP blocks: one IP
+block is used for reading video frame data from memory (FB Read) to the device
+and the other IP block is used for writing video frame data from the device
+to memory (FB Write).  Both the FB Read/Write IP blocks are aware of the
+format of the data being written to or read from memory including RGB and
+YUV in packed, planar, and semi-planar formats.  Because the FB Read/Write
+is format aware, only one buffer pointer is needed by the IP blocks even
+when planar or semi-planar format are used.
+
+FB Read Required propertie(s):
+- compatible		: Should be "xlnx,axi-frmbuf-rd-v2.1" or
+			  "xlnx,axi-frmbuf-rd-v2.2". Older string
+			  "xlnx,axi-frmbuf-rd-v2" is now deprecated.
+
+Note: Compatible string "xlnx,axi-frmbuf-rd" and the hardware it
+represented is no longer supported.
+
+FB Write Required propertie(s):
+- compatible		: Should be "xlnx,axi-frmbuf-wr-v2.1" or
+			  "xlnx,axi-frmbuf-wr-v2.2". Older string
+			  "xlnx,axi-frmbuf-wr-v2" is now deprecated.
+
+Note: Compatible string "xlnx,axi-frmbuf-wr" and the hardware it
+represented is no longer supported.
+
+Required Properties Common to both FB Read and FB Write:
+- #dma-cells		: should be 1
+- interrupt-parent	: Interrupt controller the interrupt is routed through
+- interrupts		: Should contain DMA channel interrupt
+- reset-gpios		: Should contain GPIO reset phandle
+- reg			: Memory map for module access
+- xlnx,dma-addr-width	: Size of dma address pointer in IP (either 32 or 64)
+- xlnx,vid-formats	: A list of strings indicating what video memory
+			  formats the IP has been configured to support.
+			  See VIDEO FORMATS table below and examples.
+
+Required Properties Common to both FB Read and FB Write for v2.1:
+- xlnx,pixels-per-clock	: Pixels per clock set in IP (1, 2, 4 or 8)
+- clocks: Reference to the AXI Streaming clock feeding the AP_CLK
+- clock-names: Must have "ap_clk"
+- xlnx,max-height	: Maximum number of lines.
+			  Valid range from 64 to 8640.
+- xlnx,max-width	: Maximum number of pixels in a line.
+			  Valid range from 64 to 15360.
+
+Optional Properties Common to both FB Read and FB Write for v2.1:
+- xlnx,dma-align	: DMA alignment required in bytes.
+			  If absent then dma alignment is calculated as
+			  pixels per clock * 8.
+			  If present it should be power of 2 and at least
+			  pixels per clock * 8.
+			  Minimum is 8, 16, 32 when pixels-per-clock is
+			  1, 2 or 4.
+- xlnx,fid		: Field ID enabled for interlaced video support.
+			  Can be absent for progressive video.
+
+VIDEO FORMATS
+The following table describes the legal string values to be used for
+the xlnx,vid-formats property.  To the left is the string value and the
+two columns to the right describe how this is mapped to an equivalent V4L2
+and DRM fourcc code---respectively---by the driver.
+
+IP FORMAT	DTS String	V4L2 Fourcc		DRM Fourcc
+-------------|----------------|----------------------|---------------------
+RGB8		bgr888		V4L2_PIX_FMT_RGB24	DRM_FORMAT_BGR888
+BGR8		rgb888		V4L2_PIX_FMT_BGR24	DRM_FORMAT_RGB888
+RGBX8		xbgr8888	V4L2_PIX_FMT_BGRX32	DRM_FORMAT_XBGR8888
+RGBA8		abgr8888	<not supported>		DRM_FORMAT_ABGR8888
+BGRA8		argb8888	<not supported>		DRM_FORMAT_ARGB8888
+BGRX8		xrgb8888	V4L2_PIX_FMT_XBGR32	DRM_FORMAT_XRGB8888
+RGBX10		xbgr2101010	V4L2_PIX_FMT_XBGR30	DRM_FORMAT_XBGR2101010
+RGBX12		xbgr2121212	V4L2_PIX_FMT_XBGR40	<not supported>
+RGBX16		rgb16		V4L2_PIX_FMT_BGR40	<not supported>
+YUV8		vuy888		V4L2_PIX_FMT_VUY24	DRM_FORMAT_VUY888
+YUVX8		xvuy8888	V4L2_PIX_FMT_XVUY32	DRM_FORMAT_XVUY8888
+Y_U_V8		y_u_v8		V4L2_PIX_FMT_YUV444P	DRM_FORMAT_YUV444
+Y_U_V8		y_u_v8		V4L2_PIX_FMT_YUV444M	DRM_FORMAT_YUV444
+Y_U_V10		y_u_v10		V4L2_PIX_FMT_X403	DRM_FORMAT_X403
+YUYV8		yuyv		V4L2_PIX_FMT_YUYV	DRM_FORMAT_YUYV
+UYVY8		uyvy		V4L2_PIX_FMT_UYVY	DRM_FORMAT_UYVY
+YUVA8		avuy8888	<not supported>		DRM_FORMAT_AVUY
+YUVX10		yuvx2101010	V4L2_PIX_FMT_XVUY10	DRM_FORMAT_XVUY2101010
+Y8		y8		V4L2_PIX_FMT_GREY	DRM_FORMAT_Y8
+Y10		y10		V4L2_PIX_FMT_XY10	DRM_FORMAT_Y10
+Y_UV8		nv16		V4L2_PIX_FMT_NV16	DRM_FORMAT_NV16
+Y_UV8		nv16		V4L2_PIX_FMT_NV16M	DRM_FORMAT_NV16
+Y_UV8_420	nv12		V4L2_PIX_FMT_NV12	DRM_FORMAT_NV12
+Y_UV8_420	nv12		V4L2_PIX_FMT_NV12M	DRM_FORMAT_NV12
+Y_UV10		xv20		V4L2_PIX_FMT_XV20M	DRM_FORMAT_XV20
+Y_UV10		xv20		V4L2_PIX_FMT_XV20	<not supported>
+Y_UV10_420	xv15		V4L2_PIX_FMT_XV15M	DRM_FORMAT_XV15
+Y_UV10_420	xv15		V4L2_PIX_FMT_XV20	<not supported>
+
+Examples:
+
+FB Read Example:
+++++++++
+v_frmbuf_rd_0: v_frmbuf_rd@80000000 {
+	#dma-cells = <1>;
+	compatible = "xlnx,axi-frmbuf-rd-v2.1";
+	interrupt-parent = <&gic>;
+	interrupts = <0 92 4>;
+	reset-gpios = <&gpio 80 1>;
+	reg = <0x0 0x80000000 0x0 0x10000>;
+	xlnx,dma-addr-width = <32>;
+	xlnx,vid-formats = "bgr888","xbgr8888";
+	xlnx,pixels-per-clock = <1>;
+	xlnx,dma-align = <8>;
+	clocks = <&vid_stream_clk>;
+	clock-names = "ap_clk"
+};
+
+FB Write Example:
+++++++++
+v_frmbuf_wr_0: v_frmbuf_wr@80000000 {
+	#dma-cells = <1>;
+	compatible = "xlnx,axi-frmbuf-wr-v2.1";
+	interrupt-parent = <&gic>;
+	interrupts = <0 92 4>;
+	reset-gpios = <&gpio 80 1>;
+	reg = <0x0 0x80000000 0x0 0x10000>;
+	xlnx,dma-addr-width = <64>;
+	xlnx,vid-formats = "bgr888","yuyv","nv16","nv12";
+	xlnx,pixels-per-clock = <2>;
+	xlnx,dma-align = <16>;
+	clocks = <&vid_stream_clk>;
+	clock-names = "ap_clk"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp_dma.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp_dma.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/xilinx/xlnx,zynqmp_dma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx ZynqMP DMA Controller Device Tree Bindings
+
+description:
+  Xilinx ZynqMP DMA engine, it does support memory to memory transfers,
+  memory to device and device to memory transfers. It also has flow
+  control and rate control support for slave/peripheral dma access.
+
+maintainers:
+  - Harini Katakam <harini.katakam@xilinx.com>
+  - Shravya Kumbham <shravya.kumbham@xilinx.com>
+
+allOf:
+  - $ref: "../dma-controller.yaml#"
+
+properties:
+  "#dma-cells":
+    const: 1
+    description:
+      The cell is the DMA channel ID.
+
+  compatible:
+    const: xlnx,zynqmp-dma-1.0
+
+  reg:
+    description: Memory map for gdma/adma module access.
+    maxItems: 1
+
+  interrupts:
+    description: Should contain DMA channel interrupt.
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    description: The main and apb clocks
+    items:
+      - const: clk_main
+      - const: clk_apb
+
+  xlnx,bus-width:
+    description: Axi buswidth in bits. Should contain 128 or 64.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [64, 128]
+
+  dma-coherent: true
+
+  iommus:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - "#dma-cells"
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - xlnx,bus-width
+
+additionalProperties: false
+
+examples:
+  - |
+    fpd_dma_chan1: dma-controller@fd500000 {
+      #dma-cells = <1>;
+      compatible = "xlnx,zynqmp-dma-1.0";
+      reg = <0xFD500000 0x1000>;
+      interrupt-parent = <&gic>;
+      interrupts = <0 117 4>;
+      clocks = <&dma_clk>, <&dma_clk>;
+      clock-names = "clk_main", "clk_apb";
+      xlnx,bus-width = <128>;
+      dma-coherent;
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/edac/cortex-arm64-edac.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/edac/cortex-arm64-edac.txt
@@ -0,0 +1,15 @@
+* ARM Cortex A57 and A53 L1/L2 cache error reporting
+
+CPU Memory Error Syndrome and L2 Memory Error Syndrome registers can be used
+for checking L1 and L2 memory errors.
+
+The following section describes the Cortex A57/A53 EDAC DT node binding.
+
+Required properties:
+- compatible: Should be "arm,cortex-a57-edac" or "arm,cortex-a53-edac"
+
+Example:
+	edac {
+		compatible = "arm,cortex-a57-edac";
+	};
+
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/edac/pl310_edac_l2.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/edac/pl310_edac_l2.txt
@@ -0,0 +1,19 @@
+Pl310 L2 Cache EDAC driver, it does reports the data and tag ram parity errors.
+
+Required properties:
+- compatible: Should be "arm,pl310-cache".
+- intterupts: Interrupt number to the cpu.
+- reg: Physical base address and size of cache controller's memory mapped
+  registers
+
+Example:
+++++++++
+
+	L2: cache-controller {
+		compatible = "arm,pl310-cache";
+		interrupts = <0 2 4>;
+		reg = <0xf8f02000 0x1000>;
+	};
+
+PL310 L2 Cache EDAC driver detects the Parity enable state by reading the
+appropriate control register.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/edac/xlnx,versal-ddrmc-edac.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/edac/xlnx,versal-ddrmc-edac.yaml
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/edac/xlnx,versal-ddrmc-edac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Versal DDRMC EDAC driver
+
+maintainers:
+  - Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
+
+description: |
+  Versal DDR controller has an optional ECC support which correct
+  single bit ECC errors and detect double bit ECC errors.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,versal-ddrmc-edac
+
+  reg:
+    items:
+      - description: DDR Memory Controller registers
+      - description: NOC registers corresponding to DDR Memory Controller
+
+  reg-names:
+    items:
+      - const: ddrmc_base
+      - const: ddrmc_noc_base
+
+  interrupts:
+    maxItems: 1
+
+  xlnx,mc-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Instance number of the DDR Memory Controller
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - xlnx,mc-id
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <2>;
+      #size-cells = <2>;
+      memory-controller@f6150000 {
+        compatible = "xlnx,versal-ddrmc-edac";
+        reg = <0x0 0xf6150000 0x0 0x2000>, <0x0 0xf6070000 0x0 0x20000>;
+        reg-names = "ddrmc_base", "ddrmc_noc_base";
+        interrupt-parent = <&gic>;
+        interrupts = <0 147 4>;
+        xlnx,mc-id = <0>;
+      };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/edac/xlnx,zynqmp-ocmc.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/edac/xlnx,zynqmp-ocmc.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/edac/xlnx,zynqmp-ocmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Zynqmp OCM EDAC driver
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+description: |
+  Xilinx ZynqMP OCM EDAC driver, it does reports the OCM ECC single bit errors
+  that are corrected and double bit ecc errors that are detected by the OCM
+  ECC controller.
+
+properties:
+  compatible:
+    const: xlnx,zynqmp-ocmc-1.0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+      memory-controller@ff960000 {
+        compatible = "xlnx,zynqmp-ocmc-1.0";
+        reg = <0xff960000 0x1000>;
+        interrupt-parent = <&gic>;
+        interrupts = <0 10 4>;
+      };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/edac/zynqmp_ocm_edac.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/edac/zynqmp_ocm_edac.txt
@@ -0,0 +1,18 @@
+Xilinx ZynqMP OCM EDAC driver, it does reports the OCM ECC single bit errors
+that are corrected and double bit ecc errors that are detected by the OCM
+ECC controller.
+
+Required properties:
+- compatible: Should be "xlnx,zynqmp-ocmc-1.0".
+- reg: Should contain OCM controller registers location and length.
+- interrupt-parent: Should be core interrupt controller.
+- interrupts: Property with a value describing the interrupt number.
+
+Example:
+++++++++
+ocm: memory-controller@ff960000 {
+	compatible = "xlnx,zynqmp-ocmc-1.0";
+	reg = <0x0 0xff960000 0x1000>;
+	interrupt-parent = <&gic>;
+	interrupts = <0 10 4>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/fpga/fpga-region.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/fpga/fpga-region.txt
@@ -187,6 +187,12 @@
 - external-fpga-config : boolean, set if the FPGA has already been configured
 	prior to OS boot up.
 - encrypted-fpga-config : boolean, set if the bitstream is encrypted
+- userkey-encrypted-fpga-config: boolean, set if the bitstream is encrypted with
+	user key.
+- ddrmem-authenticated-fpga-config: boolean, if set do bitstream authentication
+	using DDR memory.
+- securemem-authenticated-fpga-config: boolean, if set do bitstream
+	authenticated using secure memory.
 - region-unfreeze-timeout-us : The maximum time in microseconds to wait for
 	bridges to successfully become enabled after the region has been
 	programmed.
@@ -196,6 +202,20 @@
 - config-complete-timeout-us : The maximum time in microseconds time for the
 	FPGA to go to operating mode after the region has been programmed.
 - child nodes : devices in the FPGA after programming.
+- power-domains : A phandle and PM domain specifier as defined by bindings of
+	the power controller specified by phandle.
+Example:
+	fpga_full: fpga-full {
+                compatible = "fpga-region";
+                fpga-mgr = <&zynqmp_pcap>;
+                #address-cells = <2>;
+                #size-cells = <2>;
+                ranges;
+                power-domains = <&zynqmp_firmware PL_PD>;
+        };
+
+	The PL_PD power domain will be turned on before loading the bitstream
+and turned off while removing/unloading the bitstream using overlays.
 
 In the example below, when an overlay is applied targeting fpga-region0,
 fpga_mgr is used to program the FPGA.  Two bridges are controlled during
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/fpga/xlnx,afi-fpga.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/fpga/xlnx,afi-fpga.txt
@@ -0,0 +1,67 @@
+Xilinx ZynqMp AFI interface Manager
+
+The Zynq UltraScale+ MPSoC Processing System core provides access from PL
+masters to PS internal peripherals, and memory through AXI FIFO interface
+(AFI) interfaces.
+
+Required properties:
+-compatible:		Should contain "xlnx,afi-fpga"
+-config-afi:		Pairs of  <regid value >
+
+The possible values of regid and values are
+ regid:		Regids of the register to be written possible values
+		0- AFIFM0_RDCTRL
+		1- AFIFM0_WRCTRL
+		2- AFIFM1_RDCTRL
+		3- AFIFM1_WRCTRL
+		4- AFIFM2_RDCTRL
+		5- AFIFM2_WRCTRL
+		6- AFIFM3_RDCTRL
+		7- AFIFM3_WRCTRL
+		8- AFIFM4_RDCTRL
+		9- AFIFM4_WRCTRL
+		10- AFIFM5_RDCTRL
+		11- AFIFM5_WRCTRL
+		12- AFIFM6_RDCTRL
+		13- AFIFM6_WRCTRL
+		14- AFIFS
+		15- AFIFS_SS2
+- value:	Array of values to be written.
+		for FM0_RDCTRL(0) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM0_WRCTRL(1) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM1_RDCTRL(2) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM1_WRCTRL(3) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM2_RDCTRL(4) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM2_WRCTRL(5) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM3_RDCTRL(6) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM3_WRCTRL(7) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM4_RDCTRL(8) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM4_WRCTRL(9) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM5_RDCTRL(10) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM5_WRCTRL(11) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM6_RDCTRL(12) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for FM6_WRCTRL(13) the valid values-fabric width   2: 32-bit,1 : 64-bit ,0: 128-bit enabled
+		for AFI_FA(14)
+			dw_ss1_sel	bits (11:10)
+			dw_ss0_sel	bits (9:8)
+				0x0: 32-bit AXI data width),
+				0x1: 64-bit AXI data width,
+				0x2: 128-bit AXI data
+		All other bits are 0 write ignored.
+
+		for AFI_FA(15)  selects for ss2AXI data width valid values
+					0x000: 32-bit AXI data width),
+					0x100: 64-bit AXI data width,
+					0x200: 128-bit AXI data
+
+Optional properties:
+- resets : Phandle and reset specifier for the ps-pl reset.
+  See ../reset/reset.txt for details.
+
+Example:
+afi0: afi0 {
+	compatible = "xlnx,afi-fpga";
+	config-afi = <0 2>, <1 1>, <2 1>;
+	resets = <&zynqmp_reset 116>, <&zynqmp_reset 117>,
+		 <&zynqmp_reset 118>, <&zynqmp_reset 119>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/fpga/xlnx,zynq-afi-fpga.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/fpga/xlnx,zynq-afi-fpga.txt
@@ -0,0 +1,19 @@
+Xilinx Zynq AFI interface Manager
+
+The Zynq Processing System core provides access from PL masters to PS
+internal peripherals, and memory through AXI FIFO interface
+(AFI) interfaces.
+
+Required properties:
+-compatible:	Should contain "xlnx,zynq-afi-fpga"
+-reg:	Physical base address and size of the controller's register area.
+-xlnx,afi-buswidth :	Size of the afi bus width.
+			0: 64-bit AXI data width,
+			1: 32-bit AXI data width,
+
+Example:
+afi0: afi0 {
+	compatible = "xlnx,zynq-afi-fpga";
+	reg = <0xf8008000 0x1000>;
+	xlnx,afi-buswidth = <1>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/gpio/gpio-altera.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/gpio/gpio-altera.txt
@@ -9,8 +9,9 @@
   - The second cell is reserved and is currently unused.
 - gpio-controller : Marks the device node as a GPIO controller.
 - interrupt-controller: Mark the device node as an interrupt controller
-- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware.
+- #interrupt-cells : Should be 2. The interrupt type is fixed in the hardware.
   - The first cell is the GPIO offset number within the GPIO controller.
+  - The second cell is the interrupt trigger type and level flags.
 - interrupts: Specify the interrupt.
 - altr,interrupt-type: Specifies the interrupt trigger type the GPIO
   hardware is synthesized. This field is required if the Altera GPIO controller
@@ -38,6 +39,6 @@
 	altr,interrupt-type = <IRQ_TYPE_EDGE_RISING>;
 	#gpio-cells = <2>;
 	gpio-controller;
-	#interrupt-cells = <1>;
+	#interrupt-cells = <2>;
 	interrupt-controller;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/gpio/gpio-slg7xl45106.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/gpio/gpio-slg7xl45106.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/gpio-slg7xl45106.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: slg7xl45106 I2C GPO expander
+
+maintainers:
+  - Raviteja Narayanam <raviteja.narayanam@xilinx.com>
+
+properties:
+  compatible:
+    enum:
+      - dlg,slg7xl45106
+
+  reg:
+    maxItems: 1
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        gpio@10 {
+            compatible = "dlg,slg7xl45106";
+            reg = <0x10>;
+            gpio-controller;
+            #gpio-cells = <2>;
+        };
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/gpio/gpio-zynq.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/gpio/gpio-zynq.yaml
@@ -11,7 +11,11 @@
 
 properties:
   compatible:
-    const: xlnx,zynq-gpio-1.0
+    enum:
+      - xlnx,zynq-gpio-1.0
+      - xlnx,zynqmp-gpio-1.0
+      - xlnx,versal-gpio-1.0
+      - xlnx,pmc-gpio-1.0
 
   reg:
     maxItems: 1
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/gpio/xlnx,zynqmp-gpio-modepin.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: ZynqMP Mode Pin GPIO controller
+
+description:
+  PS_MODE is 4-bits boot mode pins sampled on POR deassertion. Mode Pin
+  GPIO controller with configurable from numbers of pins (from 0 to 3 per
+  PS_MODE). Every pin can be configured as input/output.
+
+maintainers:
+  - Piyush Mehta <piyush.mehta@xilinx.com>
+
+properties:
+  compatible:
+    const: xlnx,zynqmp-gpio-modepin
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+
+required:
+  - compatible
+  - gpio-controller
+  - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    zynqmp-firmware {
+        gpio {
+            compatible = "xlnx,zynqmp-gpio-modepin";
+            gpio-controller;
+            #gpio-cells = <2>;
+        };
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/hwmon/tps544.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/hwmon/tps544.txt
@@ -0,0 +1,14 @@
+TPS544B25 power regulator
+
+This power regulator driver supports voltage read/write and
+current calibration and readback.
+
+Required properties:
+- compatible: should be "ti,tps544"
+- reg: I2C slave address
+
+Example:
+tps544@24 {
+	compatible = "ti,tps544";
+	reg = <0x24>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/i2c/google,cros-ec-i2c-tunnel.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/i2c/google,cros-ec-i2c-tunnel.yaml
@@ -22,7 +22,7 @@
   google,cros-ec-spi or google,cros-ec-i2c.
 
 allOf:
-  - $ref: i2c-controller.yaml#
+  - $ref: /schemas/i2c/i2c-controller.yaml#
 
 properties:
   compatible:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml
@@ -14,7 +14,9 @@
 
 properties:
   compatible:
-    const: xlnx,xps-iic-2.00.a
+    enum:
+      - xlnx,xps-iic-2.00.a
+      - xlnx,axi-iic-2.1
 
   reg:
     maxItems: 1
@@ -30,6 +32,13 @@
     description: |
       Input clock name.
 
+  clock-frequency:
+    description: Desired operating frequency, in Hz, of the bus.
+                 If not specified, driver doesn't configure frequency,
+                 relies only on Vivado design IP configuration.
+
+    enum: [100000, 400000, 1000000]
+
 required:
   - compatible
   - reg
@@ -48,4 +57,5 @@
 
       #size-cells = <0>;
       #address-cells = <1>;
+      clock-frequency = <400000>;
     };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml
@@ -0,0 +1,88 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/accel/adi,adxl355.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADXL355 3-Axis, Low noise MEMS Accelerometer
+
+maintainers:
+  - Puranjay Mohan <puranjay12@gmail.com>
+
+description: |
+  Analog Devices ADXL355 3-Axis, Low noise MEMS Accelerometer that supports
+  both I2C & SPI interfaces
+    https://www.analog.com/en/products/adxl355.html
+
+properties:
+  compatible:
+    enum:
+      - adi,adxl355
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 3
+    description: |
+      Type for DRDY should be IRQ_TYPE_EDGE_RISING.
+      Three configurable interrupt lines exist.
+
+  interrupt-names:
+    description: Specify which interrupt line is in use.
+    items:
+      enum:
+        - INT1
+        - INT2
+        - DRDY
+    minItems: 1
+    maxItems: 3
+
+  vdd-supply:
+    description: Regulator that provides power to the sensor
+
+  vddio-supply:
+    description: Regulator that provides power to the bus
+
+  spi-max-frequency: true
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+        #include <dt-bindings/gpio/gpio.h>
+        #include <dt-bindings/interrupt-controller/irq.h>
+        i2c {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                /* Example for a I2C device node */
+                accelerometer@1d {
+                        compatible = "adi,adxl355";
+                        reg = <0x1d>;
+                        interrupt-parent = <&gpio>;
+                        interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+                        interrupt-names = "DRDY";
+                };
+        };
+  - |
+        #include <dt-bindings/gpio/gpio.h>
+        #include <dt-bindings/interrupt-controller/irq.h>
+        spi {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                accelerometer@0 {
+                        compatible = "adi,adxl355";
+                        reg = <0>;
+                        spi-max-frequency = <1000000>;
+                        interrupt-parent = <&gpio>;
+                        interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+                        interrupt-names = "DRDY";
+                };
+        };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml
@@ -86,7 +86,7 @@
             of the MAX chips to the GyroADC, while MISO line of each Maxim
             ADC connects to a shared input pin of the GyroADC.
         enum:
-          - adi,7476
+          - adi,ad7476
           - fujitsu,mb88101a
           - maxim,max1162
           - maxim,max11100
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/adc/ti,ina260.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/adc/ti,ina260.yaml
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/ti,ina260.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments INA260 power monitor
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+description: |
+  The INA260 is a digital-output, current, power and voltage monitor
+  with an I2C and SMBUS compatible interface with an integrated shunt
+  resistor. It features up to 16 programmable addresses on I2C compatible
+  interface. Datasheet - https://www.ti.com/lit/ds/symlink/ina260.pdf?ts=1608607288391
+
+properties:
+  compatible:
+    enum:
+      - ti,ina260
+
+  reg:
+    description: |
+      The 7-bits long I2c address of the device
+
+  "#io-channel-cells":
+    const: 1
+
+  interrupts:
+    description: |
+      IRQ line for the device
+
+  label:
+    description: |
+      A symbolic name for the device
+
+required:
+  - compatible
+  - reg
+  - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      ina260@40 {
+        compatible = "ti,ina260";
+        reg = <0x40>;
+        #io-channel-cells = <1>;
+      };
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt
@@ -0,0 +1,159 @@
+Xilinx AMS device driver
+
+The AMS includes an ADC as well as on-chip sensors that can be used to
+sample external voltages and monitor on-die operating conditions, such as
+temperature and supply voltage levels. The AMS has two SYSMON blocks.
+PL-SYSMON block is capable of monitoring off chip voltage and temperature.
+PL-SYSMON block has DRP, JTAG and I2C interface to enable monitoring from
+external master. Out of this interface currenlty only DRP is supported.
+Other block PS-SYSMON is memory mapped to PS. Both of block has built-in
+alarm generation logic that is used to interrupt the processor based on
+condition set.
+
+All designs should have AMS register, but PS and PL are optional depending on
+the design. The driver can work with only PS, only PL and both PS and PL
+configurations. Please specify registers according to your design. DTS file
+should always have AMS module property. Providing PS & PL module is optional.
+
+Required properties:
+	- compatible: Should be "xlnx,zynqmp-ams"
+	- reg:  Should specify AMS register space
+	- interrupts: Interrupt number for the AMS control interface
+	- interrupt-names: Interrupt name, must be "ams-irq"
+	- clocks: Should contain a clock specifier for the device
+	- ranges: keep the property empty to map child address space
+	          (for PS and/or PL) nodes 1:1 onto the parent address
+	          space
+
+AMS device tree subnode:
+	- compatible: Should be "xlnx,zynqmp-ams-ps" or "xlnx,zynqmp-ams-pl"
+	- reg:  Register space for PS or PL
+
+Optional properties:
+
+Following optional property only valid for PL.
+	- xlnx,ext-channels: List of external channels that are connected to the
+	                     AMS PL module.
+
+	  The child nodes of this node represent the external channels which are
+	  connected to the AMS Module. If the property is not present
+	  no external channels will be assumed to be connected.
+
+	  Each child node represents one channel and has the following
+	  properties:
+		Required properties:
+			* reg: Pair of pins the channel is connected to.
+				0: VP/VN
+				1: VUSER0
+				2: VUSER1
+				3: VUSER3
+				4: VUSER4
+				5: VAUXP[0]/VAUXN[0]
+				6: VAUXP[1]/VAUXN[1]
+				...
+				20: VAUXP[15]/VAUXN[15]
+			  Note each channel number should only be used at most
+			  once.
+		Optional properties:
+			* xlnx,bipolar: If set the channel is used in bipolar
+			  mode.
+
+
+Example:
+	xilinx_ams: ams@ffa50000 {
+		compatible = "xlnx,zynqmp-ams";
+		interrupt-parent = <&gic>;
+		interrupts = <0 56 4>;
+		interrupt-names = "ams-irq";
+		clocks = <&clkc 70>;
+		reg = <0x0 0xffa50000 0x0 0x800>;
+		reg-names = "ams-base";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ams_ps: ams_ps@ffa50800 {
+			compatible = "xlnx,zynqmp-ams-ps";
+			reg = <0x0 0xffa50800 0x0 0x400>;
+		};
+
+		ams_pl: ams_pl@ffa50c00 {
+			compatible = "xlnx,zynqmp-ams-pl";
+			reg = <0x0 0xffa50c00 0x0 0x400>;
+			xlnx,ext-channels {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				channel@0 {
+					reg = <0>;
+					xlnx,bipolar;
+				};
+				channel@1 {
+					reg = <1>;
+				};
+				channel@8 {
+					reg = <8>;
+					xlnx,bipolar;
+				};
+			};
+		};
+	};
+
+AMS Channels Details:
+
+Sysmon Block	|Channel|			Details					|Measurement
+		 Number									 Type
+---------------------------------------------------------------------------------------------------------
+AMS CTRL	|0	|System PLLs voltage measurement, VCC_PSPLL.			|Voltage
+		|1	|Battery voltage measurement, VCC_PSBATT.			|Voltage
+		|2	|PL Internal voltage measurement, VCCINT.			|Voltage
+		|3	|Block RAM voltage measurement, VCCBRAM.			|Voltage
+		|4	|PL Aux voltage measurement, VCCAUX.				|Voltage
+		|5	|Voltage measurement for six DDR I/O PLLs, VCC_PSDDR_PLL.	|Voltage
+		|6	|VCC_PSINTFP_DDR voltage measurement.				|Voltage
+---------------------------------------------------------------------------------------------------------
+PS Sysmon	|7	|LPD temperature measurement.					|Temperature
+		|8	|FPD Temperature Measurment (REMOTE).				|Temperature
+		|9	|VCC PS LPD voltage measurement (supply1).			|Voltage
+		|10	|VCC PS FPD voltage measurement (supply2).			|Voltage
+		|11	|PS Aux voltage reference (supply3).				|Voltage
+		|12	|DDR I/O VCC voltage measurement.				|Voltage
+		|13	|PS IO Bank 503 voltage measurement (supply5).			|Voltage
+		|14	|PS IO Bank 500 voltage measurement (supply6).			|Voltage
+		|15	|VCCO_PSIO1 voltage measurement.				|Voltage
+		|16	|VCCO_PSIO2 voltage measurement.				|Voltage
+		|17	|VCC_PS_GTR voltage measurement (VPS_MGTRAVCC).			|Voltage
+		|18	|VTT_PS_GTR voltage measurement (VPS_MGTRAVTT).			|Voltage
+		|19	|VCC_PSADC voltage measurement.					|Voltage
+---------------------------------------------------------------------------------------------------------
+PL Sysmon	|20	|PL Temperature measurement.					|Temperature
+		|21	|PL Internal Voltage Voltage measurement, VCCINT.		|Voltage
+		|22	|PL Auxiliary Voltage measurement, VCCAUX.			|Voltage
+		|23	|ADC Reference P+ Voltage measurement.				|Voltage
+		|24	|ADC Reference N- Voltage measurement.				|Voltage
+		|25	|PL Block RAM Voltage measurement, VCCBRAM.			|Voltage
+		|26	|LPD Internal Voltage measurement, VCC_PSINTLP (supply4).	|Voltage
+		|27	|FPD Internal Voltage measurement, VCC_PSINTFP (supply5).	|Voltage
+		|28	|PS Auxiliary Voltage measurement (supply6).			|Voltage
+		|29	|PL VCCADC Voltage measurement (vccams).			|Voltage
+		|30	|Differencial analog input signal Voltage measurment.		|Voltage
+		|31	|VUser0 Voltage measurement (supply7).				|Voltage
+		|32	|VUser1 Voltage measurement (supply8).				|Voltage
+		|33	|VUser2 Voltage measurement (supply9).				|Voltage
+		|34	|VUser3 Voltage measurement (supply10).				|Voltage
+		|35	|Auxiliary ch 0 Voltage measurement (VAux0).			|Voltage
+		|36	|Auxiliary ch 1 Voltage measurement (VAux1).			|Voltage
+		|37	|Auxiliary ch 2 Voltage measurement (VAux2).			|Voltage
+		|38	|Auxiliary ch 3 Voltage measurement (VAux3).			|Voltage
+		|39	|Auxiliary ch 4 Voltage measurement (VAux4).			|Voltage
+		|40	|Auxiliary ch 5 Voltage measurement (VAux5).			|Voltage
+		|41	|Auxiliary ch 6 Voltage measurement (VAux6).			|Voltage
+		|42	|Auxiliary ch 7 Voltage measurement (VAux7).			|Voltage
+		|43	|Auxiliary ch 8 Voltage measurement (VAux8).			|Voltage
+		|44	|Auxiliary ch 9 Voltage measurement (VAux9).			|Voltage
+		|45	|Auxiliary ch 10 Voltage measurement (VAux10).			|Voltage
+		|46	|Auxiliary ch 11 Voltage measurement (VAux11).			|Voltage
+		|47	|Auxiliary ch 12 Voltage measurement (VAux12).			|Voltage
+		|48	|Auxiliary ch 13 Voltage measurement (VAux13).			|Voltage
+		|49	|Auxiliary ch 14 Voltage measurement (VAux14).			|Voltage
+		|50	|Auxiliary ch 15 Voltage measurement (VAux15).			|Voltage
+---------------------------------------------------------------------------------------------------------
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/adc/xlnx,versal-sysmon.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/adc/xlnx,versal-sysmon.yaml
@@ -0,0 +1,143 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright 2019 - 2020 Xilinx Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/xlnx,versal-sysmon.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Versal Sysmon Linux Driver
+
+maintainers:
+  - Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
+
+description: |
+  Sysmon Driver uses Linux IIO framework which was used to abstract the supply
+  voltages and temperatures across the chip as Voltage and Temperature
+  Channels in the framework. Since there are only 160 supply voltage registers
+  and 184 measurement points, there is no constant mapping of supply voltage
+  registers and the measurement points. User has to select the voltages to
+  monitor in design tool. Depending on the selection, a voltage supply gets
+  mapped to one of the supply registers. So, this mapping information is
+  provided to the driver via a device tree. Depending on the number of supplies
+  enabled in the design, the device tree will contain the information of name
+  of the supply enabled and the supply register it maps to.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,versal-sysmon
+
+  reg:
+    description: Sysmon Registers
+    maxItems: 1
+
+  interrupts:
+    description: interrupt line for Sysmon
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  xlnx,numchannels:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    maxItems: 1
+    description: |
+      Number of supply channels enabled in the design.
+      Possible values 0 - 160. Based on this value, child supply nodes will
+      be created
+
+patternProperties:
+  "^supply@([0-9]{1,2}|1[0-5][0-9])$":
+    type: object
+    description: |
+      Represents the supplies configured in the design.
+
+    properties:
+      reg:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 159
+        description:
+          The supply number associated with the voltage.
+
+      xlnx,name:
+        $ref: /schemas/types.yaml#/definitions/string
+        description:
+          Name of the supply enabled
+
+      xlnx,bipolar:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          If the supply has a bipolar type and the output will be signed
+
+    required:
+      - reg
+      - xlnx,name
+
+required:
+  - compatible
+  - reg
+  - xlnx,numchannels
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        sysmon@f1270000 {
+            compatible = "xlnx,versal-sysmon";
+            reg = <0 0xf1270000 0 0x4000>;
+            interrupts = <0 0x90 0x4>;
+            xlnx,numchannels = /bits/8 <8>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+            supply@0 {
+                    reg = <0>;
+                    xlnx,name = "vccint";
+            };
+
+            supply@31 {
+                    reg = <31>;
+                    xlnx,name = "vccsoc";
+            };
+
+            supply@32 {
+                    reg = <32>;
+                    xlnx,bipolar;
+                    xlnx,name = "vccram";
+            };
+
+            supply@63 {
+                    reg = <63>;
+                    xlnx,bipolar;
+                    xlnx,name = "vccaux";
+            };
+
+            supply@64 {
+                    reg = <64>;
+                    xlnx,name = "vccbram";
+            };
+
+            supply@95 {
+                    reg = <95>;
+                    xlnx,name = "gt_avaux";
+            };
+
+            supply@96 {
+                    reg = <96>;
+                    xlnx,name = "gt_vccaux";
+            };
+
+            supply@159 {
+                    reg = <159>;
+                    xlnx,name = "vccint_ir";
+            };
+        };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml
@@ -54,7 +54,7 @@
 
           ad5766@0 {
               compatible = "adi,ad5766";
-              output-range-microvolts = <(-5000) 5000>;
+              output-range-microvolts = <(-5000000) 5000000>;
               reg = <0>;
               spi-cpol;
               spi-max-frequency = <1000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/gyroscope/bosch,bmg160.yaml
@@ -24,8 +24,10 @@
 
   interrupts:
     minItems: 1
+    maxItems: 2
     description:
       Should be configured with type IRQ_TYPE_EDGE_RISING.
+      If two interrupts are provided, expected order is INT1 and INT2.
 
 required:
   - compatible
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/iio/health/maxim,max30102.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/iio/health/maxim,max30102.yaml
@@ -42,7 +42,7 @@
       properties:
         compatible:
           contains:
-            const: maxim,max30100
+            const: maxim,max30102
     then:
       properties:
         maxim,green-led-current-microamp: false
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/input/adc-joystick.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/input/adc-joystick.yaml
@@ -61,11 +61,10 @@
         description: EV_ABS specific event code generated by the axis.
 
       abs-range:
-        allOf:
-          - $ref: /schemas/types.yaml#/definitions/uint32-array
-          - items:
-              - description: minimum value
-              - description: maximum value
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        items:
+          - description: minimum value
+          - description: maximum value
         description: >
           Minimum and maximum values produced by the axis.
           For an ABS_X axis this will be the left-most and right-most
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/input/hid-over-i2c.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/input/hid-over-i2c.txt
@@ -32,6 +32,8 @@
 - vdd-supply: phandle of the regulator that provides the supply voltage.
 - post-power-on-delay-ms: time required by the device after enabling its regulators
   or powering it on, before it is ready for communication.
+- touchscreen-inverted-x: See touchscreen.txt
+- touchscreen-inverted-y: See touchscreen.txt
 
 Example:
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/interrupt-controller/xilinx,intc.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/interrupt-controller/xilinx,intc.txt
@@ -0,0 +1,56 @@
+Xilinx Interrupt Controller
+
+The controller is a soft IP core that is configured at build time for the
+number of interrupts and the type of each interrupt. These details cannot
+be changed at run time.
+
+Required properties:
+
+- compatible : should be "xlnx,xps-intc-1.00.a"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+		     interrupt source. The value shall be a minimum of 1.
+		     The Xilinx device trees typically use 2 but the 2nd value
+		     is not used.
+- xlnx,kind-of-intr : A 32 bit value specifying the interrupt type for each
+		      possible interrupt (1 = edge, 0 = level). The interrupt
+		      type typically comes in thru the device tree node of
+		      the interrupt generating device, but in this case
+		      the interrupt type is determined by the interrupt
+		      controller based on how it was implemented.
+- xlnx,num-intr-inputs: Specifies the number of interrupts supported
+		        by the specific implementation of the controller (1-32).
+
+Optional properties:
+- interrupt-parent : Specifies an interrupt controller from which it is
+		     chained (cascaded).
+- interrupts : Specifies the interrupt of the parent controller from which
+	       it is chained.
+
+Example:
+
+axi_intc_0: interrupt-controller@41800000 {
+	#interrupt-cells = <2>;
+	compatible = "xlnx,xps-intc-1.00.a";
+	interrupt-controller;
+	reg = <0x41800000 0x10000>;
+	xlnx,kind-of-intr = <0x1>;
+	xlnx,num-intr-inputs = <0x1>;
+};
+
+Chained Example:
+
+The interrupt is chained to hardware interrupt 61 (29 + 32) of the GIC
+for Zynq.
+
+axi_intc_0: interrupt-controller@41800000 {
+	#interrupt-cells = <2>;
+	compatible = "xlnx,xps-intc-1.00.a";
+	interrupt-controller;
+	interrupt-parent = <&ps7_scugic_0>;
+	interrupts = <0 29 4>;
+	reg = <0x41800000 0x10000>;
+	xlnx,kind-of-intr = <0x1>;
+	xlnx,num-intr-inputs = <0x1>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml
@@ -32,8 +32,9 @@
 patternProperties:
   "^multi-led@[0-9a-b]$":
     type: object
-    allOf:
-      - $ref: leds-class-multicolor.yaml#
+    $ref: leds-class-multicolor.yaml#
+    unevaluatedProperties: false
+
     description:
       This node represents one of the RGB LED devices on Turris Omnia.
       No subnodes need to be added for subchannels since this controller only
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/leds/leds-class-multicolor.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/leds/leds-class-multicolor.yaml
@@ -19,22 +19,22 @@
   LED class.  Common LED nodes and properties are inherited from the common.yaml
   within this documentation directory.
 
-patternProperties:
-  "^multi-led@([0-9a-f])$":
-    type: object
-    description: Represents the LEDs that are to be grouped.
-    properties:
-      color:
-        description: |
-          For multicolor LED support this property should be defined as either
-          LED_COLOR_ID_RGB or LED_COLOR_ID_MULTI which can be found in
-          include/linux/leds/common.h.
-        enum: [ 8, 9 ]
+properties:
+  $nodename:
+    pattern: "^multi-led(@[0-9a-f])?$"
 
-    $ref: "common.yaml#"
+  color:
+    description: |
+      For multicolor LED support this property should be defined as either
+      LED_COLOR_ID_RGB or LED_COLOR_ID_MULTI which can be found in
+      include/dt-bindings/leds/common.h.
+    enum: [ 8, 9 ]
 
-    required:
-      - color
+required:
+  - color
+
+allOf:
+  - $ref: "common.yaml#"
 
 additionalProperties: true
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
@@ -55,8 +55,9 @@
 patternProperties:
   '^multi-led@[0-9a-f]$':
     type: object
-    allOf:
-      - $ref: leds-class-multicolor.yaml#
+    $ref: leds-class-multicolor.yaml#
+    unevaluatedProperties: false
+
     properties:
       reg:
         minItems: 1
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-pwm-multicolor.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Multi-color LEDs connected to PWM
+
+maintainers:
+  - Sven Schwermer <sven.schwermer@disruptive-technologies.com>
+
+description: |
+  This driver combines several monochrome PWM LEDs into one multi-color
+  LED using the multicolor LED class.
+
+properties:
+  compatible:
+    const: pwm-leds-multicolor
+
+  multi-led:
+    type: object
+    $ref: leds-class-multicolor.yaml#
+    unevaluatedProperties: false
+
+    patternProperties:
+      "^led-[0-9a-z]+$":
+        type: object
+        $ref: common.yaml#
+
+        additionalProperties: false
+
+        properties:
+          pwms:
+            maxItems: 1
+
+          pwm-names: true
+
+          color: true
+
+        required:
+          - pwms
+          - color
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/leds/common.h>
+
+    led-controller {
+        compatible = "pwm-leds-multicolor";
+
+        multi-led {
+          color = <LED_COLOR_ID_RGB>;
+          function = LED_FUNCTION_INDICATOR;
+          max-brightness = <65535>;
+
+          led-red {
+              pwms = <&pwm1 0 1000000>;
+              color = <LED_COLOR_ID_RED>;
+          };
+
+          led-green {
+              pwms = <&pwm2 0 1000000>;
+              color = <LED_COLOR_ID_GREEN>;
+          };
+
+          led-blue {
+              pwms = <&pwm3 0 1000000>;
+              color = <LED_COLOR_ID_BLUE>;
+          };
+        };
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-qcom-lpg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Light Pulse Generator
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: >
+  The Qualcomm Light Pulse Generator consists of three different hardware blocks;
+  a ramp generator with lookup table, the light pulse generator and a three
+  channel current sink. These blocks are found in a wide range of Qualcomm PMICs.
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm8150b-lpg
+      - qcom,pm8150l-lpg
+      - qcom,pm8916-pwm
+      - qcom,pm8941-lpg
+      - qcom,pm8994-lpg
+      - qcom,pmc8180c-lpg
+      - qcom,pmi8994-lpg
+      - qcom,pmi8998-lpg
+
+  "#pwm-cells":
+    const: 2
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  qcom,power-source:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      power-source used to drive the output, as defined in the datasheet.
+      Should be specified if the TRILED block is present
+    enum: [0, 1, 3]
+
+  qcom,dtest:
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    description: >
+      A list of integer pairs, where each pair represent the dtest line the
+      particular channel should be connected to and the flags denoting how the
+      value should be outputed, as defined in the datasheet. The number of
+      pairs should be the same as the number of channels.
+    items:
+      items:
+        - description: dtest line to attach
+        - description: flags for the attachment
+
+  multi-led:
+    type: object
+    $ref: leds-class-multicolor.yaml#
+    unevaluatedProperties: false
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+    patternProperties:
+      "^led@[0-9a-f]$":
+        type: object
+        $ref: common.yaml#
+
+patternProperties:
+  "^led@[0-9a-f]$":
+    type: object
+    $ref: common.yaml#
+
+    properties:
+      reg: true
+
+    required:
+      - reg
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/leds/common.h>
+
+    led-controller {
+      compatible = "qcom,pmi8994-lpg";
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      qcom,power-source = <1>;
+
+      qcom,dtest = <0 0>,
+                   <0 0>,
+                   <0 0>,
+                   <4 1>;
+
+      led@1 {
+        reg = <1>;
+        color = <LED_COLOR_ID_GREEN>;
+        function = LED_FUNCTION_INDICATOR;
+        function-enumerator = <1>;
+      };
+
+      led@2 {
+        reg = <2>;
+        color = <LED_COLOR_ID_GREEN>;
+        function = LED_FUNCTION_INDICATOR;
+        function-enumerator = <0>;
+        default-state = "on";
+      };
+
+      led@3 {
+        reg = <3>;
+        color = <LED_COLOR_ID_GREEN>;
+        function = LED_FUNCTION_INDICATOR;
+        function-enumerator = <2>;
+      };
+
+      led@4 {
+        reg = <4>;
+        color = <LED_COLOR_ID_GREEN>;
+        function = LED_FUNCTION_INDICATOR;
+        function-enumerator = <3>;
+      };
+    };
+  - |
+    #include <dt-bindings/leds/common.h>
+
+    led-controller {
+      compatible = "qcom,pmi8994-lpg";
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      qcom,power-source = <1>;
+
+      multi-led {
+        color = <LED_COLOR_ID_RGB>;
+        function = LED_FUNCTION_STATUS;
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        led@1 {
+          reg = <1>;
+          color = <LED_COLOR_ID_RED>;
+        };
+
+        led@2 {
+          reg = <2>;
+          color = <LED_COLOR_ID_GREEN>;
+        };
+
+        led@3 {
+          reg = <3>;
+          color = <LED_COLOR_ID_BLUE>;
+        };
+      };
+    };
+  - |
+    pwm-controller {
+      compatible = "qcom,pm8916-pwm";
+      #pwm-cells = <2>;
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/i2c/onnn,ap1302.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/i2c/onnn,ap1302.yaml
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/onnn,ap1302.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ON Semiconductor AP1302 Advanced Image Coprocessor
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+  - Anil Kumar M <anil.mamidala@xilinx.com>
+
+description: |-
+  The AP1302 is a standalone ISP for ON Semiconductor sensors. It interfaces to
+  up to two RAW CMOS sensors over MIPI CSI-2 connections, processes the two
+  video streams and outputs YUV frames to the host over a MIPI CSI-2 interface.
+  Frames are output side by side or on two virtual channels.
+
+  The sensors must be identical. They are connected to the AP1302 on dedicated
+  I2C buses, and are controlled by the AP1302 firmware. They are not accessible
+  from the host.
+
+properties:
+  compatible:
+    const: onnn,ap1302
+
+  reg:
+    description: I2C device address.
+    maxItems: 1
+
+  clocks:
+    description: Reference to the CLK clock.
+    maxItems: 1
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the RST pin (active low).
+    maxItems: 1
+
+  standby-gpios:
+    description:
+      Reference to the GPIO connected to the STANDBY pin (active high).
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    unevaluatedProperties: false
+    description: MIPI CSI-2 output interface to the host.
+
+    properties:
+      endpoint:
+        $ref: /schemas/graph.yaml#/$defs/endpoint-base
+        unevaluatedProperties: false
+
+        properties:
+          clock-noncontinuous:
+            type: boolean
+
+          data-lanes:
+            oneOf:
+              - items:
+                  - const: 1
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+        required:
+          - data-lanes
+
+  sensors:
+    type: object
+    description: List of connected sensors
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      onnn,model:
+        $ref: "/schemas/types.yaml#/definitions/string"
+        description: |
+          Model of the connected sensors. Must be a valid compatible string.
+
+          If no sensor is connected, this property must no be specified, and
+          the AP1302 can be used with it's internal test pattern generator.
+
+    patternProperties:
+      "^sensor@[01]":
+        type: object
+        description: |
+          Sensors connected to the first and second input, with one node per
+          sensor.
+
+        properties:
+          reg:
+            description: AP1302 input port number
+            maxItems: 1
+
+        patternProperties:
+          ".*-supply":
+            description: Power supplies for the sensor
+
+        required:
+          - reg
+
+        additionalProperties: false
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+
+    # How can we express that onnn,model requires one sensor object to be set ?
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+  - sensors
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@3c {
+            compatible = "onnn,ap1302";
+            reg = <0x3c>;
+
+            clocks = <&clk24mhz>;
+
+            reset-gpios = <&pio 102 GPIO_ACTIVE_LOW>;
+            standby-gpios = <&pio 40 GPIO_ACTIVE_HIGH>;
+
+            port {
+                isp1_out: endpoint {
+                    remote-endpoint = <&seninf_in1>;
+                    data-lanes = <1 2 3 4>;
+                };
+            };
+
+            sensors {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                onnn,model = "onnn,ar0144";
+
+                sensor@0 {
+                    reg = <0>;
+
+                    vdd-supply = <&mt6358_vcamd_reg>;
+                    vaa-supply = <&mt6358_vcama1_reg>;
+                    vddio-supply = <&reg_1p8v_ext>;
+                };
+            };
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@3c {
+            compatible = "onnn,ap1302";
+            reg = <0x3c>;
+
+            clocks = <&topckgen 0>;
+
+            reset-gpios = <&pio 102 GPIO_ACTIVE_LOW>;
+            standby-gpios = <&pio 40 GPIO_ACTIVE_HIGH>;
+
+            port {
+                isp2_out: endpoint {
+                    remote-endpoint = <&seninf_in1>;
+                    data-lanes = <1 2>;
+                };
+            };
+
+            sensors {
+                #address-cells = <1>;
+                #size-cells = <0>;
+            };
+        };
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/i2c/onnn,ar1335.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/i2c/onnn,ar1335.yaml
@@ -0,0 +1,98 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/onnn,ar1335.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: AR1335 1/3.2‐Inch 13 Mp CMOS Digital Image Sensor 
+
+maintainers:
+  - Anil Kumar M <anil.mamidala@amd.com>
+
+description: |-
+  The AR1335 from ON Semiconductor is a 1/3.2-inch BSI (Back Side Illuminated)
+  CMOS active-pixel digital image sensor with a pixel array of 4208 (H) × 3120 (V).
+  It is programmable through I2C interface. Image data is sent through MIPI CSI-2, 
+  serial data lanes.
+
+properties:
+  compatible:
+    const: ar1335 
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: |-
+      Reference to the GPIO connected to the reset pin.
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    unevaluatedProperties: false
+    description: MIPI CSI-2 output interface to the host.
+
+    properties:
+      clock-lanes:
+        description: |-
+          lane for extrenal clock.
+
+      data-lanes:
+        description: |-
+          Two, three and four-lane supported, for four-lane operation the 
+          property must be set to <1 2 3 4>.
+        oneOf:
+          - items:
+              - const: 1
+              - const: 1
+          - items:
+              - const: 1
+              - const: 2
+              - const: 2
+          - items:
+              - const: 1
+              - const: 2
+              - const: 3
+              - const: 4
+
+        required:
+          - data-lanes
+          - clock-lanes
+
+      endpoint:
+        $ref: /schemas/graph.yaml#/$defs/endpoint-base
+        unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ar1335: sensor@36 {
+            compatible = "ar1335";
+            reg = <0x36>;
+            reset-gpios = <&axi_gpio 2 0>;
+
+            port {
+                clock-lanes = <0>;
+                data-lanes = <1 2 3 4>;
+                ar1335_out: endpoint {
+                    remote-endpoint = <&csi_ep>;
+                };
+            };
+        };
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
@@ -37,15 +37,15 @@
       active low.
     maxItems: 1
 
-  dovdd-supply:
+  DOVDD-supply:
     description:
       Definition of the regulator used as interface power supply.
 
-  avdd-supply:
+  AVDD-supply:
     description:
       Definition of the regulator used as analog power supply.
 
-  dvdd-supply:
+  DVDD-supply:
     description:
       Definition of the regulator used as digital power supply.
 
@@ -59,9 +59,9 @@
   - reg
   - clocks
   - clock-names
-  - dovdd-supply
-  - avdd-supply
-  - dvdd-supply
+  - DOVDD-supply
+  - AVDD-supply
+  - DVDD-supply
   - reset-gpios
   - port
 
@@ -82,9 +82,9 @@
                 clock-names = "xvclk";
                 reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
-                dovdd-supply = <&sw2_reg>;
-                dvdd-supply = <&sw2_reg>;
-                avdd-supply = <&reg_peri_3p15v>;
+                DOVDD-supply = <&sw2_reg>;
+                DVDD-supply = <&sw2_reg>;
+                AVDD-supply = <&reg_peri_3p15v>;
 
                 port {
                         ov2680_to_mipi: endpoint {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
@@ -79,6 +79,8 @@
 
             properties:
               data-lanes:
+                description:
+                  Note that 'fsl,imx7-mipi-csi2' only supports up to 2 data lines.
                 items:
                   minItems: 1
                   maxItems: 4
@@ -91,18 +93,6 @@
             required:
               - data-lanes
 
-            allOf:
-              - if:
-                  properties:
-                    compatible:
-                      contains:
-                        const: fsl,imx7-mipi-csi2
-                then:
-                  properties:
-                    data-lanes:
-                      items:
-                        maxItems: 2
-
       port@1:
         $ref: /schemas/graph.yaml#/properties/port
         description:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,axis-broadcaster.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,axis-broadcaster.yaml
@@ -0,0 +1,179 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/xilinx/xlnx,axis-broadcaster.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx AXI4-Stream Broadcaster
+
+maintainers:
+  - Ronak Shah <ronak.shah@xilinx.com>
+
+description: |
+  The AXI4-Stream Broadcaster provides a solution for replicating a single
+  inbound AXI4-Stream interface into multiple outbound AXI4-Stream interfaces.
+  Support for up to 16 outbound AXI4-Stream interfaces is provided.
+  For more details, Please refer to PG085 AXI4-Stream Infrastructure IP Suite.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,axis-broadcaster-1.1
+
+  # See ./video-interfaces.txt for details
+  ports:
+    type: object
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      port@0:
+        type: object
+        description: |
+          Input/sink port node, describing module connected to the
+          input of AXI4-Stream Broadcaster.
+
+        properties:
+          reg:
+            description: |
+              Input/sink port number.
+            const: 0
+
+          endpoint:
+            type: object
+
+            properties:
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+            additionalProperties: false
+
+        required:
+          - reg
+          - endpoint
+
+        additionalProperties: false
+
+    patternProperties:
+      "^port@([1-9]|1[0-6])$":
+        type: object
+        description: |
+          Output/source port node, describing module connected to the
+          output of AXI4-Stream Broadcaster.
+
+        properties:
+          reg:
+            description: |
+              Output/source port number. It can have min 2 ports and
+              max 16 ports, numbered from 1 to 16.
+            items:
+              minimum: 1
+              maximum: 16
+
+          endpoint:
+            type: object
+
+            properties:
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+            additionalProperties: false
+
+        required:
+          - reg
+          - endpoint
+
+        additionalProperties: false
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+      - port@0
+      - port@1
+      - port@2
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    axis_broadcaster_0 {
+        compatible = "xlnx,axis-broadcaster-1.1";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                /* Sink port */
+                reg = <0>;
+                axis_broad_0_in: endpoint {
+                    remote-endpoint = <&v_proc_ss_out>;
+                };
+            };
+            port@1 {
+                /* Source port */
+                reg = <1>;
+                axis_broad_0_out1: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_0_in>;
+                };
+            };
+            port@2 {
+                /* Source port */
+                reg = <2>;
+                axis_broad_0_out2: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_1_in>;
+                };
+            };
+            port@3 {
+                /* Source port */
+                reg = <3>;
+                axis_broad_0_out3: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_2_in>;
+                };
+            };
+            port@4 {
+                /* Source port */
+                reg = <4>;
+                axis_broad_0_out4: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_3_in>;
+                };
+            };
+            port@5 {
+                /* Source port */
+                reg = <5>;
+                axis_broad_0_out5: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_4_in>;
+                };
+            };
+            port@6 {
+                /* Source port */
+                reg = <6>;
+                axis_broad_0_out6: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_5_in>;
+                };
+            };
+            port@7 {
+                /* Source port */
+                reg = <7>;
+                axis_broad_0_out7: endpoint {
+                    remote-endpoint = <&v_frmbuf_wr_6_in>;
+                };
+            };
+        };
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,axis-subsetconv.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,axis-subsetconv.yaml
@@ -0,0 +1,133 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/xilinx/xlnx,axis-subsetconv.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Subset Converter
+
+maintainers:
+  - Anil Kumar Mamidala <anil.mamidala@xilinx.com>
+  - Karthikeyan T <karthikeyan.thangavel@xilinx.com>
+
+description: |
+    This subset converter driver is for the Xilinx subset converter
+    IP which is a non-memory mapped IP used for converting formats.
+    The format conversion of source pad and sink pad in the pipeline
+    done by subset converter IP will be mapped in this driver.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,axis-subsetconv-1.1
+
+  # See ./video-interfaces.txt for details
+  ports:
+    type: object
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      port@0:
+        type: object
+        description: |
+          Input/sink port node, describing module connected to the
+          input of AXI4-Stream Subset Converter.
+
+        properties:
+          reg:
+            description: |
+              Input/sink port number.
+            const: 0
+
+          endpoint:
+            type: object
+
+            properties:
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+            additionalProperties: false
+
+        required:
+          - reg
+          - endpoint
+
+        additionalProperties: false
+
+    patternProperties:
+      "port@1":
+        type: object
+        description: |
+          Output/source port node, describing module connected to the
+          output.
+
+        properties:
+          reg:
+            description: |
+              Output/source port number.
+
+          endpoint:
+            type: object
+
+            properties:
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+            additionalProperties: false
+
+        required:
+          - reg
+          - endpoint
+
+        additionalProperties: false
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+      - port@0
+      - port@1
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+   axis_subsetconv_0 {
+        compatible = "xlnx,axis-subsetconv-1.1";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                /* Sink port */
+                reg = <0>;
+                subset_conv_in: endpoint {
+                    remote-endpoint = <&isp_csiss_out>;
+                };
+            };
+            port@1 {
+                /* Source port */
+                reg = <1>;
+                subset_conv_out: endpoint {
+                    remote-endpoint = <&isp_vcap_csi_in>;
+                };
+            };
+        };
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml
@@ -50,6 +50,7 @@
       Packets other than this data type (except for RAW8 and
       User defined data types) will be filtered out.
       Possible values are as below -
+      0x18 - YUV4208B
       0x1e - YUV4228B
       0x1f - YUV42210B
       0x20 - RGB444
@@ -67,6 +68,7 @@
       0x2f - RAW20
     $ref: /schemas/types.yaml#/definitions/uint32
     oneOf:
+      - 0x18
       - minimum: 0x1e
         maximum: 0x24
       - minimum: 0x28
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,mem2mem.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,mem2mem.txt
@@ -0,0 +1,25 @@
+Xilinx Video IP MEM2MEM Pipeline (XVIM2M)
+----------------------------------------
+
+Xilinx video IP mem2mem pipeline processes DMA transfers to achieve memory
+copy from one physical memory to other. The data is copied by employing two
+DMA transfers memory to device and device to memory transactions one after
+the other. The DT node of the XVIM2M represents as a top level node of the
+pipeline and defines mappings between DMAs.
+
+Required properties:
+
+- compatible: Must be "xlnx,mem2mem".
+
+- dmas, dma-names: List of two DMA specifier and identifier strings (as
+  defined in Documentation/devicetree/bindings/dma/dma.txt) per port.
+  Identifier string of one DMA channel should be "tx" and other should be
+  "rx".
+
+Example:
+
+	video_m2m {
+		compatible = "xlnx,mem2mem";
+		dmas = <&dma_1 0>, <&dma_2 0>;
+		dma-names = "tx", "rx";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt
@@ -0,0 +1,77 @@
+
+Xilinx SDI Receiver Subsystem
+------------------------------
+
+The Xilinx SDI Rx Subsystem is used to capture SDI Video in upto 12G mode.
+It outputs the video as an AXI4 Stream video data in YUV 422 10bpc mode.
+The subsystem consists of the SDI Rx IP whose SDI native output is connected
+to a SDI to Native conversion Bridge. The output of the Native bridge is
+connected to a Native to AXI4S Bridge which generates the AXI4 Stream of
+YUV422 or YUV420 10 bpc in dual pixel per clock.
+
+Required properties:
+
+- compatible: Must contain "xlnx,v-smpte-uhdsdi-rx-ss"
+
+- reg: Physical base address and length of the registers set for the device.
+
+- interrupts: Contains the interrupt line number.
+
+- interrupt-parent: phandle to interrupt controller.
+
+- xlnx,include-edh: Whether the EDH processor is enabled in design or not.
+
+- xlnx,line-rate: The maximum mode supported by the design.
+
+- clocks: Input clock specifier. Refer to common clock bindings.
+
+- clock-names: List of input clocks.
+  Required elements: "s_axi_aclk", "sdi_rx_clk", "video_out_clk"
+
+- port: Video port, using the DT bindings defined in ../video-interfaces.txt.
+  The SDI Rx subsystem has one port configured as output port.
+
+- xlnx,video-format, xlnx,video-width: Video format and width, as defined in
+  video.txt. Please note that the video format is fixed to either YUV422 or YUV420
+  and the video-width is 10.
+
+Optional properties:
+
+- reset_gt-gpios: contains GPIO reset phandle for FMC init done pin in GT.
+  This pin is active low.
+- picxo_reset-gpios: contains GPIO reset phandle for PICXO done pin for PICXO module.
+  This pin is active high.
+- xlnx,bpp: This denotes the bit depth as 10 or 12 based on IP configuration.
+  The default value is 10 for backward compatibility.
+
+Example:
+		v_smpte_uhdsdi_rx_ss: v_smpte_uhdsdi_rx_ss@80000000 {
+			compatible = "xlnx,v-smpte-uhdsdi-rx-ss";
+			interrupt-parent = <&gic>;
+			interrupts = <0 89 4>;
+			reg = <0x0 0x80000000 0x0 0x10000>;
+			xlnx,include-axilite = "true";
+			xlnx,include-edh = "true";
+			xlnx,include-vid-over-axi = "true";
+			xlnx,line-rate = "12G_SDI_8DS";
+			clocks = <&clk_1>, <&si570_1>, <&clk_2>;
+			clock-names = "s_axi_aclk", "sdi_rx_clk", "video_out_clk";
+			reset_gt-gpios = <&axi_gpio_0 0 0 GPIO_ACTIVE_LOW>;
+			picxo_reset-gpios = <&axi_gpio_0 2 0 GPIO_ACTIVE_HIGH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					xlnx,video-format = <XVIP_VF_YUV_422>;
+					xlnx,video-width = <10>;
+
+					sdirx_out: endpoint {
+						remote-endpoint = <&vcap_sdirx_in>;
+					};
+				};
+			};
+		};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-axi4s-switch.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-axi4s-switch.txt
@@ -0,0 +1,141 @@
+Xilinx AXI4-Stream Switch
+-------------------------------
+
+The AXI4-Stream Switch provides configurable routing between masters and slaves.
+It supports up to 16 masters/sources and 16 slaves/sinks and two routing options.
+There is atleast one slave/sink port and two master/source ports.
+
+The two routing options available are TDEST routing and control register routing.
+The TDEST based routing uses design parameters and hence there no software control.
+Each port is mapped as a pad and has its own format specified.
+
+Control register routing introduces an AXI4-Lite interface to configure the
+routing table. There is one register for each of the master interfaces to
+control each of the selectors. This routing mode requires that there is
+precisely only one path between master and slave. When attempting to map the
+same slave interface to multiple master interfaces, only the lowest master
+interface is able to access the slave interface.
+Here only the slave/sink ports have formats as master/source ports will inherit
+the corresponding slave ports formats. A routing table is maintained in this case.
+
+Please refer to PG085 AXI4-Stream Infrastructure IP Suite v2.2 for more details.
+
+Required properties:
+
+ - compatible: Must be "xlnx,axis-switch-1.1".
+ - xlnx,routing-mode: Can be 0 (TDEST routing) or 1 (Control reg routing)
+ - xlnx,num-si-slots: Number of slave / input ports. Min 1 Max 16 .
+ - xlnx,num-mi-slots: Number of master / output ports. Min 1 Max 16.
+ - ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+ - clocks: Reference to the AXI Streaming clock feeding the ACLK and
+   AXI4 Lite control interface clock when control routing is enabled.
+ - clock-names: Must have "aclk".
+
+Optional properties:
+ - reg: Physical base address and length of the registers set for the device.
+	This is required only if xlnx,routing-mode is 1.
+ - clocks: Reference to AXI4 Lite control interface clock when routing-mode is 1.
+ - clock-names: "s_axi_ctl_clk" clock for AXI4 Lite interface when routing-mode is 1.
+
+Example:
+
+For TDEST routing, from 1 slave port to 4 master ports
+
+	axis_switch_0: axis_switch@0 {
+		compatible = "xlnx,axis-switch-1.1";
+		xlnx,routing-mode = <0x0>;
+		xlnx,num-si-slots = <0x1>;
+		xlnx,num-mi-slots = <0x4>;
+		clocks = <&vid_stream_clk>;
+		clock-names = "aclk";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				switch_in0: endpoint {
+					remote-endpoint = <&csirxss_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				switch_out0: endpoint {
+					remote-endpoint = <&vcap_csirxss0_in>;
+				};
+			};
+			port@2 {
+				reg = <2>;
+				switch_out1: endpoint {
+					remote-endpoint = <&vcap_csirxss1_in>;
+				};
+			};
+			port@3 {
+				reg = <3>;
+				switch_out2: endpoint {
+					remote-endpoint = <&vcap_csirxss2_in>;
+				};
+			};
+			port@4 {
+				reg = <4>;
+				switch_out3: endpoint {
+					remote-endpoint = <&vcap_csirxss3_in>;
+				};
+			};
+		};
+
+	};
+
+For Control reg based routing, from 2 slave ports to 4 master ports
+
+	axis_switch_0: axis_switch@a0050000 {
+		compatible = "xlnx,axis-switch-1.1";
+		reg = <0x0 0xa0050000 0x0 0x1000>;
+		xlnx,routing-mode = <0x1>;
+		xlnx,num-si-slots = <0x2>;
+		xlnx,num-mi-slots = <0x4>;
+		clocks = <&vid_stream_clk>, <&misc_clk_0>;
+		clock-names = "aclk", "s_axi_ctl_clk;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				switch_in0: endpoint {
+					remote-endpoint = <&csirxss_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				switch_in1: endpoint {
+					remote-endpoint = <&tpg_out>;
+				};
+			};
+			port@2 {
+				reg = <2>;
+				switch_out0: endpoint {
+					remote-endpoint = <&vcap_csirxss0_in>;
+				};
+			};
+			port@3 {
+				reg = <3>;
+				switch_out1: endpoint {
+					remote-endpoint = <&vcap_csirxss1_in>;
+				};
+			};
+			port@4 {
+				reg = <4>;
+				switch_out2: endpoint {
+					remote-endpoint = <&vcap_csirxss2_in>;
+				};
+			};
+			port@5 {
+				reg = <5>;
+				switch_out3: endpoint {
+					remote-endpoint = <&vcap_csirxss3_in>;
+				};
+			};
+		};
+
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-cfa.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-cfa.txt
@@ -0,0 +1,58 @@
+Xilinx Color Filter Array (CFA)
+-------------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,v-cfa-7.0".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the video core clock.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The cfa has an input port (0) and an output port (1).
+
+Required port properties:
+
+- xlnx,video-format: Must be SENSOR_MONO for the input port (0), and RBG for
+  the output port (1).
+
+- xlnx,video-width: Video width as defined in video.txt
+
+- xlnx, cfa-pattern: Must be one of "rggb", "grbg", "gbrg", and "bggr" for the
+  input port (0). Must not be specified for the output port (1).
+
+Example:
+
+	cfa_0: cfa@400b0000 {
+		compatible = "xlnx,v-cfa-7.0";
+		reg = <0x400b0000 0x10000>;
+		clocks = <&clkc 15>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_SENSOR_MONO>;
+				xlnx,video-width = <8>;
+				xlnx,cfa-pattern = "rggb";
+
+				cfa0_in: endpoint {
+					remote-endpoint = <&spc0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_RBG>;
+				xlnx,video-width = <8>;
+
+				cfa0_out: endpoint {
+					remote-endpoint = <&ccm0_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-cresample.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-cresample.txt
@@ -0,0 +1,54 @@
+Xilinx Chroma Resampler (CRESAMPLE)
+-----------------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,v-cresample-4.0".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the video core clock.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The cresample as han input port (0) and an output port (1).
+
+Required port properties:
+
+- xlnx,video-format: Must be one of YUV_444, YUV_422 or YUV_420 for the input
+  port (0), and one of YUV_422 or YUV_420 for the output port (1).
+
+- xlnx,video-width: Video width as defined in video.txt
+
+Example:
+
+	cresample_0: cresample@40120000 {
+		compatible = "xlnx,v-cresample-4.0";
+		reg = <0x40120000 0x10000>;
+		clocks = <&clkc 15>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_YUV_444>;
+				xlnx,video-width = <8>;
+
+				cresample0_in: endpoint {
+					remote-endpoint = <&rgb2yuv0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				cresample0_out: endpoint {
+					remote-endpoint = <&scaler0_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-demosaic.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-demosaic.txt
@@ -0,0 +1,62 @@
+Xilinx Video Demosaic IP
+-----------------------------
+The Xilinx Video Demosaic IP is used to interface to a Bayer video source.
+
+The driver set default Sink Pad media bus format to RGGB.
+The IP and driver only support RGB as its Source Pad media format.
+
+Required properties:
+
+- compatible: Must be "xlnx,v-demosaic".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the AXI Streaming clock feeding the Demosaic ap_clk.
+
+- xlnx,max-height: Maximum number of lines. Valid range is 64 to 4320.
+
+- xlnx,max-width: Maximum number of pixels in a line. Valid range is 64 to 8192.
+
+- reset-gpios: Specifier for GPIO that asserts Demosaic IP (AP_RST_N) reset.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+
+Required port properties:
+
+- reg: This value represents the media pad of the V4L2 sub-device.
+  A Sink Pad is represented by reg = <0>
+  A Source Pad is represented by reg = <1>
+
+- xlnx,video-width: Video width as defined in video.txt
+
+Example:
+	demosaic_1: demosaic@a00b0000 {
+		compatible = "xlnx,v-demosaic";
+		reg = <0x0 0xa00b0000 0x0 0x10000>;
+		clocks = <&vid_stream_clk>;
+		reset-gpios = <&gpio 87 1>;
+		xlnx,max-width = <3840>;
+		xlnx,max-height = <2160>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				xlnx,video-width = <8>;
+
+				demosaic_in: endpoint {
+					remote-endpoint = <&tpg_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				xlnx,video-width = <8>;
+
+				demosaic_out: endpoint {
+					remote-endpoint = <&gamma_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-dprxss.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-dprxss.yaml
@@ -0,0 +1,178 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/xilinx/xlnx,v-dprxss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx DisplayPort Receiver Subsystem
+
+maintainers:
+  - Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>
+
+description: |
+  The DisplayPort subsystem is a full feature, hierarchically packaged
+  subsystem with a DisplayPort sink(RX). DP RX subsystem can capture
+  video data in different formats at different resolutions.
+  For more details, please refer to PG233 at
+  https://www.xilinx.com/support/documentation/ip_documentation/dp_rx_subsystem/v2_1/pg233-displayport-rx-subsystem.pdf
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,v-dprxss-3.0
+
+  reg:
+    minItems: 1
+    items:
+      - description: DisplayPort Receiver Subsystem registers
+      - description: EDID IP block registers
+
+  reg-names:
+    items:
+      - const: dp_base
+      - const: edid_base
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: List of clock specifiers
+    items:
+      - description: AXI Lite clock
+      - description: Link clock
+      - description: Video clock
+
+  clock-names:
+    items:
+      - const: s_axi_aclk
+      - const: rx_lnk_clk
+      - const: rx_vid_clk
+
+  phys:
+    description: This denotes phandles for phy lanes registered for DP
+                 protocol. Number of phy lanes registered are depends on
+                 the xlnx,lane-count property.
+
+  phy-names:
+    items:
+      - const: dp-phy0
+      - const: dp-phy1
+      - const: dp-phy2
+      - const: dp-phy3
+
+  xlnx,link-rate:
+    description: |
+      Max link rate that IP configured with.Possible values are as below -
+      0x6  - 1.62 Gb/s
+      0xa  - 2.7 Gb/s
+      0x14 - 5.4 Gb/s
+      0x1e - 8.1 Gb/s
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0x6, 0xa, 0x14, 0x1e]
+
+  xlnx,lane-count:
+    description: Max number of lanes that IP configured with.
+                 Possible values are 1, 2, 4.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4]
+
+  xlnx,bpc:
+    description: |
+      Max BPC value that IP configured with. For example if IP is
+      configured
+      with 10 BPC means it supports (6, 8, 10) up to 10bpc.
+      Possible values are 6, 8, 10, 12, 16.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [6, 8, 10, 12, 16]
+
+  xlnx,audio-channels:
+    description: |
+      This denotes number of audio channels enabled in the IP
+      configuration. Possible values are 2, 3, 4, 5, 6, 7, 8.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [2, 3, 4, 5, 6, 7, 8]
+
+  ports:
+    type: object
+
+    properties:
+      port@0:
+        type: object
+        description: |
+          Output / source port node, endpoint describing modules
+          connected the DisplayPort receiver
+
+        properties:
+          reg:
+            const: 0
+
+          endpoint:
+            type: object
+
+            properties:
+
+              remote-endpoint: true
+
+            required:
+              - remote-endpoint
+
+            additionalProperties: false
+
+        additionalProperties: false
+
+required:
+  - clock-names
+  - clocks
+  - compatible
+  - interrupts
+  - reg
+  - reg-names
+  - link-rate
+  - bpc
+  - lane-count
+  - phy-names
+  - phys
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+   v_dp_rxss1@a0040000 {
+       clock-names = "s_axi_aclk", "rx_lnk_clk", "rx_vid_clk" ;
+       clocks = <&zynqmp_clk 71>, <&zynqmp_clk 72>;
+       compatible = "xlnx,v-dp-rxss-3.0";
+       interrupt-names = "dprxss_dp_irq";
+       interrupt-parent = <&gic>;
+       interrupts = <0 89 4>;
+       reg = <0xa0040000 0x40000>, <0xa0010000 0x1000>;
+       reg-names = "dp_base", "edid_base";
+       xlnx,link-rate = <0x1e>;
+       xlnx,audio-enable;
+       xlnx,audio-channels = <2>;
+       xlnx,bpc = <10>;
+       xlnx,hdcp22-enable;
+       xlnx,hdcp-enable;
+       xlnx,lane-count = <4>;
+       phy-names = "dp-phy0", "dp-phy1", "dp-phy2", "dp-phy3";
+       phys = <&vphy_lane0 0 1 1 0>, <&vphy_lane1 0 1 1 0>,
+              <&vphy_lane2 0 1 1 0>, <&vphy_lane3 0 1 1 0>;
+
+       ports {
+           #address-cells = <1>;
+           #size-cells = <0>;
+
+           port@0 {
+               reg = <0>;
+               dp_rxss_out: endpoint {
+                   remote-endpoint = <&remap0_in>;
+               };
+           };
+       };
+   };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-gamma-lut.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-gamma-lut.txt
@@ -0,0 +1,63 @@
+Xilinx Video Gamma Correction IP
+-----------------------------------
+The Xilinx Video Gamma Correction IP is used to provide RGB gamma correction.
+The IP provides a look up table for each R,G and B components.
+
+Required properties:
+
+- compatible: Must be "xlnx,v-gamma-lut".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the clock that drives the ap_clk
+	  signal of Video Gamma Lookup.
+
+- xlnx,max-height: Maximum number of lines. Valid range is 64 to 4320.
+
+- xlnx,max-width: Maximum number of pixels in a line. Valid range is 64 to 8192.
+
+- reset-gpios: Specifier for a GPIO that asserts Gamma IP (AP_RST_N) reset
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The Gamma LUT IP has an input port (0) and an output port (1).
+
+
+Required port properties:
+- reg: This value represents the media pad of the V4L2 sub-device.
+  A Sink Pad is represented by reg = <0>
+  A Source Pad is represented by reg = <1>
+
+- xlnx,video-width: Video width as defined in video.txt. Can be either 8 or 10.
+
+Example:
+
+	gamma_lut_1: gamma_lut_1@0xa0080000 {
+		compatible = "xlnx,v-gamma-lut";
+		reg = <0x0 0xa0080000 0x0 0x10000>;
+		clocks = <&vid_stream_clk>;
+		reset-gpios = <&gpio 83 1>;
+		xlnx,max-height = <2160>;
+		xlnx,max-width = <3840>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				xlnx,video-width = <8>;
+
+				gamma_in: endpoint {
+					remote-endpoint = <&demosaic_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				xlnx,video-width = <8>;
+
+				gamma_out: endpoint {
+					remote-endpoint = <&csc_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-hdmi-rxss1.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-hdmi-rxss1.yaml
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/xilinx/xlnx,v-hdmi-rxss1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx HDMI 2.1 Receiver Subsystem
+
+maintainers:
+  - Vishal Sagar <vishal.sagar@xilinx.com>
+
+description: |
+  The Xilinx HDMI 2.1 Receiver Subsystem is a feature rich soft IP incorporating
+  all the necesssary logic to properly interface with PHY layer and provides HDMI
+  decoding functionality. The subsystem is a hierarchical IP that bundles a
+  collection of HDMI 2.1 Rx-related IP sub-cores and outputs them as a  single IP.
+  The subsystem receives the captured TMDS data from the PHY layer. It then
+  extracts the video and audio streams from the HDMI stream and converts it to
+  video and audio streams.
+  For more details refer to PG 351 Xilinx HDMI 2.1 Rx Subsystem.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,v-hdmi-rxss1-1.1
+          - xlnx,v-hdmi-rxss1-1.2
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Clock for AXI4-Lite control interface
+      - description: Fixed FRL Link clock
+      - description: AXI4-Stream clock
+
+  clock-names:
+    items:
+      - const: s_axi_cpu_aclk
+      - const: frl_clk
+      - const: s_axis_video_aclk
+
+  xlnx,edid-ram-size:
+    description: |
+      This is size of EDID in BRAM.
+      The possible values are 256, 512, 1024 or 4096.
+      This property has to be specified as '/bits/ 16' value.
+    $ref: /schemas/types.yaml#/definitions/uint16
+    enum: [ 256, 512, 1024, 4096 ]
+
+  xlnx,input-pixels-per-clock:
+    description: |
+      Number of pixels per clock on Video Interface.
+      This property has to be specified as '/bits/ 8' value.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    enum: [ 4, 8 ]
+
+  xlnx,max-bits-per-component:
+    description: |
+      Maximum bits per component.
+      This property has to be specified as '/bits/ 8' value.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    enum: [ 8, 10, 12, 16 ]
+
+  xlnx,max-frl-rate:
+    description: |
+      Maximum FRL rate.
+      This property has to be specified as '/bits/ 8' value.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    enum: [ 4, 5, 6 ]
+
+  xlnx,frl-clk-freq-khz:
+    description: |
+      FRL clock frequency in KHz
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  xlnx,vid-clk-freq-khz:
+    description: |
+      Video clock frequency in KHz
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  phys:
+    description: |
+      This denotes phandles for phy lanes registered for HDMI protocol.
+
+  phy-names:
+    items:
+      - const: hdmi-phy0
+      - const: hdmi-phy1
+      - const: hdmi-phy2
+      - const: hdmi-phy3
+
+  ports:
+    type: object
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      port@0:
+        type: object
+        description: |
+          Sink port node with one endpoint connected to a hdmi-connector node.
+        properties:
+          reg:
+            const: 0
+          endpoint:
+            type: object
+            properties:
+              remote-endpoint: true
+            required:
+              - remote-endpoint
+            additionalProperties: false
+        additionalProperties: false
+
+      port@1:
+        type: object
+        description: |
+          Source port node with one endpoint.
+        properties:
+          reg:
+            const: 1
+          endpoint:
+            type: object
+            properties:
+              remote-endpoint: true
+            required:
+              - remote-endpoint
+            additionalProperties: false
+        additionalProperties: false
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+      - port@0
+      - port@1
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - xlnx,edid-ram-size
+  - xlnx,max-bits-per-component
+  - xlnx,max-frl-rate
+  - xlnx,frl-clk-freq-khz
+  - xlnx,vid-clk-freq-khz
+  - xlnx,input-pixels-per-clock
+  - phys
+  - phy-names
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    v_hdmi_rxss1: v_hdmi_rxss1@80000000 {
+      compatible = "xlnx,v-hdmi-rxss1-1.1";
+      reg = <0x80000000 0x10000>;
+      clock-names = "s_axi_cpu_aclk", "frl_clk", "s_axis_video_aclk";
+      clocks = <&zynqmp_clk 71>, <&misc_clk_4>, <&misc_clk_5>;
+      interrupt-parent = <&gic>;
+      interrupts = <0 90 4>;
+      xlnx,edid-ram-size = /bits/ 16 <0x100>;
+      xlnx,input-pixels-per-clock = /bits/ 8 <0x8>;
+      xlnx,max-bits-per-component = /bits/ 8 <0xa>;
+      xlnx,max-frl-rate = /bits/ 8 <0x6>;
+      xlnx,frl-clk-freq-khz = <449955>;
+      xlnx,vid-clk-freq-khz = <400000>;
+      phy-names = "hdmi-phy0", "hdmi-phy1", "hdmi-phy2", "hdmi-phy3";
+      phys = <&hdmiphy1_lane0 0 1 1 0>,
+             <&hdmiphy1_lane1 0 1 1 0>,
+             <&hdmiphy1_lane2 0 1 1 0>,
+             <&hdmiphy1_lane3 0 1 1 0>;
+      ports {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        port@0 {
+           reg = <0>;
+           hdmi_rx_in: endpoint {
+             remote-endpoint = <&hdmi_connector_out>;
+           };
+        };
+        port@1 {
+           reg = <1>;
+           hdmi_rx_out: endpoint {
+             remote-endpoint = <&vpss_in>;
+           };
+        };
+      };
+    };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-hls.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-hls.txt
@@ -0,0 +1,64 @@
+Xilinx High-Level Synthesis Core (HLS)
+--------------------------------------
+
+High-Level Synthesis cores are synthesized from a high-level function
+description developed by the user. As such their functions vary widely, but
+they all share a set of common characteristics that allow them to be described
+by common bindings.
+
+
+Required properties:
+
+- compatible: This property must contain "xlnx,v-hls" to indicate that the
+  core is compatible with the generic Xilinx HLS DT bindings. It can also
+  contain a more specific string to identify the HLS core implementation. The
+  value of those implementation-specific strings is out of scope for these DT
+  bindings.
+
+- reg: Physical base address and length of the registers sets for the device.
+  The HLS core has two registers sets, the first one contains the core
+  standard registers and the second one contains the custom user registers.
+
+- clocks: Reference to the video core clock.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The HLS core has one input port (0) and one output port (1).
+
+Required port properties:
+
+- xlnx,video-format: Video format as defined in video.txt.
+- xlnx,video-width: Video width as defined in video.txt.
+
+Example:
+
+	hls_0: hls@43c00000 {
+		compatible = "xlnx,v-hls-sobel", "xlnx,v-hls";
+		reg = <0x43c00000 0x24>, <0x43c00024 0xa0>;
+		clocks = <&clkc 15>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				hls0_in: endpoint {
+					remote-endpoint = <&vdma_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				hls0_out: endpoint {
+					remote-endpoint = <&vdma_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-multi-scaler.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-multi-scaler.txt
@@ -0,0 +1,95 @@
+Xilinx mem2mem Multi Video Scaler (XM2MSC)
+-----------------------------------------
+
+Required propertie(s):
+- compatible		: Should be "xlnx,v-multi-scaler-v1.0"
+- clocks		: Input clock specifier. Refer to common clk bindings.
+- interrupt-parent	: Interrupt controller the interrupt is routed through
+- interrupts		: Should contain MultiScaler interrupt
+- reset-gpios		: Should contain GPIO reset phandle
+- reg			: Physical base address and
+			  length of the registers set for the device.
+- xlnx,max-chan		: Maximum number of supported scaling channels (1 - 8)
+- xlnx,max-width	: Maximum number of supported column/width (64 - 3840)
+- xlnx,max-height	: Maximum number of supported row/height (64 - 2160)
+- xlnx,dma-addr-width	: dma address width (either 32 or 64)
+- xlnx,pixels-per-clock	: pixels per clock set in IP (1, 2 or 4)
+- xlnx,vid-formats	: A list of strings indicating what video memory
+			  formats the IP has been configured to support.
+			  See VIDEO FORMATS table below and examples.
+- xlnx,num-taps		: The number of filter taps for scaling (6, 8, 10, 12)
+
+VIDEO FORMATS
+The following table describes the legal string values to be used for
+the xlnx,vid-formats property. To the left is the string value and the
+column to the right describes the format.
+
+IP FORMAT	DTS String	Description
+-------------|----------------|---------------------
+RGB8		bgr888		Packed RGB, 8 bits per component.
+				Every RGB pixel in memory is represented with
+				24 bits.
+RGBX8		xbgr8888	Packed RGB, 8 bits per component. Every RGB
+				pixel in memory is represented with 32 bits.
+				Bits[31:24] do not contain pixel information.
+BGRX8		xrgb8888	Packed BGR, 8 bits per component. Every BGR
+				pixel in memory is represented with 32 bits.
+				Bits[31:24] do not contain pixel information.
+RGBX10		xbgr2101010	Packed RGB, 10 bits per component. Every RGB
+				pixel is represented with 32 bits. Bits[31:30]
+				do not contain any pixel information.
+YUV8		vuy888		Packed YUV 4:4:4, 8 bits per component. Every
+				YUV 4:4:4 pixel in memory is represented with
+				24 bits.
+YUVX8		xvuy8888	Packed YUV 4:4:4, 8 bits per component.
+				Every YUV 4:4:4 pixel in memory is represented
+				with 32 bits. Bits[31:24] do not contain pixel
+				information.
+YUYV8		yuyv		Packed YUV 4:2:2, 8 bits per component. Every
+				two YUV 4:2:2 pixels in memory are represented
+				with 32 bits.
+UYVY8		uyvy		Packed YUV 4:2:2, 8 bits per component.
+				Every two YUV 4:2:2 pixels in memory are
+				represented with 32 bits.
+YUVX10		yuvx2101010	Packed YUV 4:4:4, 10 bits per component.
+				Every YUV 4:4:4 pixel is represented with 32 bits.
+				Bits[31:30] do not contain any pixel information.
+Y8		y8		Packed Luma-Only, 8 bits per component. Every
+				luma-only pixel in memory is represented with
+				8 bits. Y8 is presented as YUV 4:4:4 on the
+				AXI4-Stream interface.
+Y10		y10		Packed Luma-Only, 10 bits per component. Every
+				three luma-only pixels in memory is represented
+				with 32 bits. Y10 is presented as YUV 4:4:4 on
+				the AXI4-Stream interface.
+Y_UV8		nv16		Semi-planar YUV 4:2:2 with 8 bits per component.
+				Y and UV stored in separate planes.
+Y_UV8_420	nv12		Semi-planar YUV 4:2:0 with 8 bits per component.
+				Y and UV stored in separate planes.
+Y_UV10		xv20		Semi-planar YUV 4:2:2 with 10 bits per component.
+				Every 3 pixels is represented with 32 bits.
+				Bits[31:30] do not contain any pixel information.
+				Y and UV stored in separate planes.
+Y_UV10_420	xv15		Semi-planar YUV 4:2:0 with 10 bits per component.
+				Every 3 pixels is represented with 32 bits.
+				Bits[31:30] do not contain any pixel information.
+				Y and UV stored in separate planes.
+
+Example
+
+v_multi_scaler_0: v_multi_scaler@a0000000 {\
+	clocks = <&clk 71>;
+	compatible = "xlnx,v-multi-scaler-v1.0";
+	interrupt-names = "interrupt";
+	interrupt-parent = <&gic>;
+	interrupts = <0 89 4>;
+	reg = <0x0 0xa0000000 0x0 0x10000>;
+	xlnx,vid-formats = "bgr888","vuy888";
+	reset-gpios = <&gpio 78 1>;
+	xlnx,max-chan = <0x01>;
+	xlnx,dma-addr-width = <0x20>;
+	xlnx,pixels-per-clock = /bits/ 8 <2>;
+	xlnx,max-width = <3840>;
+	xlnx,max-height = <2160>;
+	xlnx,num-taps = <6>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-remapper.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-remapper.txt
@@ -0,0 +1,61 @@
+Xilinx Video Remapper
+---------------------
+
+The IP core remaps input pixel components to produce an output pixel with
+less, more or the same number of components as the input pixel.
+
+Required properties:
+
+- compatible: Must be "xlnx,v-remapper".
+
+- clocks: Reference to the video core clock.
+
+- xlnx,video-width: Video pixel component width, as defined in video.txt.
+
+- #xlnx,s-components: Number of components per pixel at the input port
+  (between 1 and 4 inclusive).
+
+- #xlnx,m-components: Number of components per pixel at the output port
+  (between 1 and 4 inclusive).
+
+- xlnx,component-maps: Remapping configuration represented as an array of
+  integers. The array contains one entry per output component, in the low to
+  high order. Each entry corresponds to the zero-based position of the
+  corresponding input component, or the value 4 to drive a constant value on
+  the output component. For example, to remap RGB to BGR use <2 1 0>, and to
+  remap RBG to xRGB use <1 0 2 4>.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The remapper as an input port (0) and and output port (1).
+
+Example: RBG to xRGB remapper
+
+	remapper_0: remapper {
+		compatible = "xlnx,v-remapper";
+
+		clocks = <&clkc 15>;
+
+		xlnx,video-width = <8>;
+
+		#xlnx,s-components = <3>;
+		#xlnx,m-components = <4>;
+		xlnx,component-maps = <1 0 2 4>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				remap0_in: endpoint {
+					remote-endpoint = <&tpg0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				remap0_out: endpoint {
+					remote-endpoint = <&sobel0_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-rgb2yuv.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-rgb2yuv.txt
@@ -0,0 +1,54 @@
+Xilinx RGB to YUV (RGB2YUV)
+---------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,v-rgb2yuv-7.1".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the video core clock.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The rgb2yuv has an input port (0) and an output port (1).
+
+Required port properties:
+
+- xlnx,video-format: Must be RBG for the input port (0) and YUV_444 for the
+  output port (1).
+
+- xlnx,video-width: Video width as defined in video.txt
+
+Example:
+
+	rgb2yuv_0: rgb2yuv@40100000 {
+		compatible = "xlnx,v-rgb2yuv-7.1";
+		reg = <0x40100000 0x10000>;
+		clocks = <&clkc 15>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_RBG>;
+				xlnx,video-width = <8>;
+
+				rgb2yuv0_in: endpoint {
+					remote-endpoint = <&gamma0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_YUV_444>;
+				xlnx,video-width = <8>;
+
+				rgb2yuv0_out: endpoint {
+					remote-endpoint = <&cresample0_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-scaler.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-scaler.txt
@@ -0,0 +1,75 @@
+Xilinx Scaler (SCALER)
+------------------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,v-scaler-8.1".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the video core clock.
+
+- xlnx,num-hori-taps, xlnx,num-vert-taps: The number of horizontal and vertical
+  taps for scaling filter(range: 2 - 12).
+
+- xlnx,max-num-phases: The maximum number of phases for scaling filter
+  (range: 2 - 64).
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The scaler has an input port (0) and an output port (1).
+
+Optional properties:
+
+- xlnx,separate-yc-coef: When set, this boolean property specifies that
+  the hardware uses separate coefficients for the luma and chroma filters.
+  Otherwise a single set of coefficients is shared for both.
+
+- xlnx,separate-hv-coef: When set, this boolean property specifies that
+  the hardware uses separate coefficients for the horizontal and vertical
+  filters. Otherwise a single set of coefficients is shared for both.
+
+Required port properties:
+
+- xlnx,video-format: Must be one of RBG, YUV_422, YUV_422 or YUV_420 for
+  both input port (0) and output port (1). The two formats must be identical.
+
+- xlnx,video-width: Video width as defined in video.txt
+
+Example:
+
+	scaler_0: scaler@43c30000 {
+		compatible = "xlnx,v-scaler-8.1";
+		reg = <0x43c30000 0x10000>;
+		clocks = <&clkc 15>;
+
+		xlnx,num-hori-taps = <12>;
+		xlnx,num-vert-taps = <12>;
+		xlnx,max-num-phases = <4>;
+		xlnx,separate-hv-coef;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				scaler0_in: endpoint {
+					remote-endpoint = <&cresample0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				scaler0_out: endpoint {
+					remote-endpoint = <&vcap0_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-scd.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-scd.txt
@@ -0,0 +1,164 @@
+Xilinx Scene Change Detection IP (SCD)
+--------------------------------------
+
+The Xilinx Scene Change Detection IP contains two blocks: one IP block is used
+for reading video frame data from memory to the device and the other IP block
+is used for determining whether there is a scene change between current and the
+previous frame. The IP supports YUV planar and semi-planar formats. IP only
+needs luma frame to determine the scene change event. The IP supports memory
+based model, which means that it will accept a dma buffer address and perform
+MEM2DEV transfer followed by statistical based image processing and give the
+data back to application if scene change detection is present or not.
+
+Another version of scene change detection IP which supports streaming model,
+which means that IP can be inserted in a capture pipeline. For example,
+"hdmirx -> streaming-scd -> fb_wr" is a typical capture pipeline where
+streaming SCD can be embedded. The IP accespts the AXI video data and perform
+histogram based statistical analysis to detect scene change. The IP supports
+single channel.
+
+Required properties:
+
+- compatible: Should be "xlnx,v-scd"
+
+- reg: Physical base address and length of the registers set for the device
+
+- clocks: Reference to the video core clock.
+
+- reset-gpios: Specifier for a GPIO that assert SCD (AP_RST_N) reset.
+
+- xlnx,memory-based: This is to differentiate between memory based and
+  streaming based IP. The value is 1 for memory based and 0 for streaming
+  based IPs.
+
+- xlnx,numstreams: Maximum active streams IP can support is 8 and this is based
+  on the design.
+
+- xlnx,addrwidth: Size of dma address pointer in IP (either 32 or 64)
+
+- subdev: Each channel will have its own subdev node. Each subdev will have its
+  sink port.
+
+- port: Video port, using the DT bindings defined in ../video-interfaces.txt.
+
+Example:
+
+1. Memory based device tree
+
+The following example shows how the device tree would look like for a memory
+based design where 8 streams are enabled.
+
+	scd: scenechange@a0100000 {
+		compatible = "xlnx,v-scd";
+		reg = <0x0 0xa0100000 0x0 0x1fff>;
+		clocks = <&misc_clk_0>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 90 4>;
+		reset-gpios = <&gpio 94 1>;
+
+		xlnx,memory-based;
+		xlnx,numstreams = <8>;
+		xlnx,addrwidth = <0x20>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#dma-cells = <1>;
+
+		subdev@0 {
+			port@0 {
+				reg = <0>;
+				scd_in0: endpoint {
+					remote-endpoint = <&vcap0_out0>;
+				};
+			};
+		};
+		subdev@1 {
+			port@0 {
+				reg = <0>;
+				scd_in1: endpoint {
+					remote-endpoint = <&vcap0_out1>;
+				};
+			};
+		};
+		subdev@2 {
+			port@0 {
+				reg = <0>;
+				scd_in2: endpoint {
+					remote-endpoint = <&vcap0_out2>;
+				};
+			};
+		};
+		subdev@3 {
+			port@0 {
+				reg = <0>;
+				scd_in3: endpoint {
+					remote-endpoint = <&vcap0_out3>;
+				};
+			};
+		};
+		subdev@4 {
+			port@0 {
+				reg = <0>;
+				scd_in4: endpoint {
+					remote-endpoint = <&vcap0_out4>;
+				};
+			};
+		};
+		subdev@5 {
+			port@0 {
+				reg = <0>;
+				scd_in5: endpoint {
+					remote-endpoint = <&vcap0_out5>;
+				};
+			};
+		};
+		subdev@6 {
+			port@0 {
+				reg = <0>;
+				scd_in6: endpoint {
+					remote-endpoint = <&vcap0_out6>;
+				};
+			};
+		};
+		subdev@7 {
+			port@0 {
+				reg = <0>;
+			scd_in7: endpoint {
+					remote-endpoint = <&vcap0_out7>;
+				};
+			};
+		};
+	};
+
+2. Streaming based device tree
+
+The following example shows how the device tree would look like for a streaming
+based design.
+
+	scd: scenechange@a0280000 {
+		compatible = "xlnx,v-scd";
+		reg = <0x0 0xa0280000 0x0 0x1fff>;
+		clocks = <&clk 72>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 111 4>;
+		reset-gpios = <&gpio 100 1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		xlnx,numstreams = <1>;
+
+		scd {
+			port@0 {
+				reg = <0x0>;
+				scd_in0: endpoint {
+					remote-endpoint = <&vpss_scaler_out>;
+				};
+			};
+
+			port@1 {
+				reg = <0x1>;
+				scd_out0: endpoint {
+					remote-endpoint = <&vcap_hdmi_in_1>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-switch.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-switch.txt
@@ -0,0 +1,55 @@
+Xilinx Video Switch
+-------------------
+
+Required properties:
+
+  - compatible: Must be "xlnx,v-switch-1.0".
+
+  - reg: Physical base address and length of the registers set for the device.
+
+  - clocks: Reference to the video core clock.
+
+  - #xlnx,inputs: Number of input ports
+  - #xlnx,outputs: Number of outputs ports
+
+  - ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+
+Example:
+
+	switch: switch@43c10000 {
+		compatible = "xlnx,v-switch-1.0";
+		reg = <0x43c10000 0x10000>;
+		clocks = <&clkc 15>;
+
+		#xlnx,inputs = <2>;
+		#xlnx,outputs = <2>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				switch_in0: endpoint {
+					remote-endpoint = <&tpg_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				switch_in1: endpoint {
+					remote-endpoint = <&cresample0_out>;
+				};
+			};
+			port@2 {
+				reg = <2>;
+				switch_out0: endpoint {
+					remote-endpoint = <&scaler0_in>;
+				};
+			};
+			port@3 {
+				reg = <3>;
+				switch_out1: endpoint {
+					remote-endpoint = <&vcap0_in1>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt
@@ -6,7 +6,8 @@
 - compatible: Must contain at least one of
 
     "xlnx,v-tpg-5.0" (TPG version 5.0)
-    "xlnx,v-tpg-6.0" (TPG version 6.0)
+    "xlnx,v-tpg-7.0" (TPG version 7.0)
+    "xlnx,v-tpg-8.0" (TPG version 8.0)
 
   TPG versions backward-compatible with previous versions should list all
   compatible versions in the newer to older order.
@@ -23,6 +24,8 @@
 
 Optional properties:
 
+- xlnx,ppc: Pixels per clock. Valid values are 1, 2, 4 or 8.
+
 - xlnx,vtc: A phandle referencing the Video Timing Controller that generates
   video timings for the TPG test patterns.
 
@@ -30,16 +33,26 @@
   input. The GPIO active level corresponds to the selection of VTC-generated
   video timings.
 
+- reset-gpios: Specifier for a GPIO that assert TPG (AP_RST_N) reset.
+  This property is mandatory for TPG v7.0 and above.
+
+- xlnx,max-height: Maximum number of lines.
+  This property is mandatory for TPG v8.0. Value ranges from 64 to 7760.
+
+- xlnx,max-width: Maximum number of pixels in a line.
+  This property is mandatory for TPG v8.0. Value ranges from 64 to 10328.
+
 The xlnx,vtc and timing-gpios properties are mandatory when the TPG is
 synthesized with two ports and forbidden when synthesized with one port.
 
 Example:
 
 	tpg_0: tpg@40050000 {
-		compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0";
+		compatible = "xlnx,v-tpg-5.0";
 		reg = <0x40050000 0x10000>;
 		clocks = <&clkc 15>;
 
+		xlnx,ppc = <2>;
 		xlnx,vtc = <&vtc_3>;
 		timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-vpss-csc.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-vpss-csc.txt
@@ -0,0 +1,67 @@
+Xilinx VPSS Color Space Converter (CSC)
+-----------------------------------------
+The Xilinx VPSS Color Space Converter (CSC) is a Video IP that supports
+color space conversion from RGB or YUV(444, 422, 420)input to RGB or
+YUV(444, 422, 420) output.
+
+Required properties:
+
+- compatible: Must be "xlnx,v-vpss-csc".
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the clock that drives the ap_clk signal.
+
+- xlnx,max-height: Maximum number of lines.
+  Valid range from 64 to 4320.
+
+- xlnx,max-width: Maximum number of pixels in a line.
+  Valid range from 64 to 8192.
+
+- reset-gpios: Specifier for a GPIO that assert VPSS CSC (AP_RST_N) reset.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The scaler has an input port (0) and an output port (1).
+
+Required port properties:
+
+- xlnx,video-format: Must be XVIP_VF_RBG, XVIP_VF_YUV_444 or XVIP_VF_YUV_422
+  for input port (0) and XVIP_VF_RBG, XVIP_VF_YUV_444 or XVIP_VF_YUV_422
+  for output port (1). See <dt-bindings/media/xilinx-vip.h> for more details.
+
+- xlnx,video-width: Video width as defined in video.txt. Must be either 8 or 10.
+
+Example:
+	csc_1:csc@a0040000 {
+		compatible = "xlnx,v-vpss-csc";
+		reg = <0x0 0xa0040000 0x0 0x10000>;
+		clocks = <&vid_stream_clk>;
+		reset-gpios = <&gpio 84 1>;
+		xlnx,max-width = <3840>;
+		xlnx,max-height = <2160>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* Sink Pad */
+			port@0 {
+				reg = <0>;
+				xlnx,video-format = <XVIP_VF_RBG>;
+				xlnx,video-width = <8>;
+
+				csc_in: endpoint {
+					remote-endpoint = <&gamma_out>;
+				};
+			};
+			/* Source Pad */
+			port@1 {
+				reg = <1>;
+				xlnx,video-format = <XVIP_VF_RBG>;
+				xlnx,video-width = <8>;
+
+				csc_out: endpoint {
+					remote-endpoint = <&scalar_in>;
+				};
+			};
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,v-vpss-scaler.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,v-vpss-scaler.txt
@@ -0,0 +1,93 @@
+  Xilinx VPSS Scaler
+------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,v-vpss-scaler-2.2" or "xlnx,v-vpss-scaler-1.0".
+  The older string "xlnx,v-vpss-scaler" will be deprecated.
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the AXI Streaming clock feeding the VPSS Scaler AP_CLK
+  and AXI4 Lite control interface clock.
+
+- clock-names: Must contain "aclk_axis" and "aclk_ctrl" in the same order as
+  clocks listed in clocks property.
+
+- xlnx,num-hori-taps, xlnx,num-vert-taps: The number of horizontal and vertical
+  taps for scaling filter(range: 2,4,6,8,10,12).
+
+  A value of 2 represents bilinear filters. A value of 4 represents bicubic.
+  Values 6,8,10,12 represent polyphase filters.
+
+- xlnx,pix-per-clk : The pixels per clock property of the IP
+
+- reset-gpios: Specifier for a GPIO that assert for VPSS Scaler reset.
+  This property is mandatory for the Scaler
+
+- xlnx,max-height: Maximum number of lines.
+  Valid range from 64 to 4320.
+
+- xlnx,max-width: Maximum number of pixels in a line.
+  Valid range from 64 to 8192.
+
+- ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+  The scaler has an input port (0) and an output port (1).
+
+Required port properties:
+
+- xlnx,video-format: Must be one of XVIP_VF_RBG or XVIP_VF_YUV_422 for
+  input port (0) and must be XVIP_VF_RBG or XVIP_VF_YUV_422 or for
+  the output port (1).
+  See <dt-bindings/media/xilinx-vip.h> for more details.
+
+- reg: This value represents the media pad of the V4L2 sub-device.
+  A Sink Pad is represented by reg = <0>
+  A Source Pad is represented by reg = <1>
+
+- xlnx,video-width: Video width as defined in video.txt
+
+Example:
+
+	scaler_1:scaler@a0000000 {
+		compatible = "xlnx,v-vpss-scaler-1.0";
+		reg = <0x0 0xa0000000 0x0 0x40000>;
+		clocks = <&vid_stream_clk>, <&misc_clk_2>;
+		clock-names = "aclk_axis", "aclk_ctrl";
+		xlnx,num-hori-taps = <8>;
+		xlnx,num-vert-taps = <8>;
+		xlnx,pix-per-clk = <2>;
+		reset-gpios = <&gpio 87 1>;
+		xlnx,max-width = <3840>;
+		xlnx,max-height = <2160>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				/* Sink Pad */
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_RBG>;
+				xlnx,video-width = <8>;
+
+				scaler_in: endpoint {
+					remote-endpoint = <&csc_out>;
+				};
+			};
+
+			port@1 {
+				/* Source Pad */
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				scaler_out: endpoint {
+					remote-endpoint = <&vcap_tpg_in>;
+				};
+			};
+		};
+
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt
@@ -21,6 +21,18 @@
 
 - ports: Video port, using the DT bindings defined in ../video-interfaces.txt.
 
+Optional properties:
+- memory-region : phandle to /reserved-memory node.
+  If memory is reserved for special use by DMAs then this node
+  can be used to refer and use from this reserved memory region.
+
+- xlnx,atomic_streamon: This property is useful for the scenario where some of
+  the upstream entities are being shared with multiple video devices (dma
+  engines) in the same media pipeline. When set, all entities belonging to
+  the media pipeline will get enabled even when any one of the dma engine
+  present in the media  pipeline start streaming, otherwise the entities
+  get enabled only when all dma engines start streaming.
+
 Required port properties:
 
 - direction: should be either "input" or "output" depending on the direction
@@ -53,3 +65,46 @@
 			};
 		};
 	};
+
+Example using reserved memory:
+Reserving from 32bit Shared CMA pool of 512MiB using System RAM:
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+/ {
+	reserved-memory {
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		ranges;
+		psmem_multimedia: multimedia_cma_mem_region {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x40000000 0x00 0x20000000>;
+			reusable;
+		};
+	};
+};
+...
+	video_cap {
+		/* ... */
+		memory-region = <&psmem_multimedia>;
+	};
+
+
+Reserving from 64bit Shared DMA pool of 1792 MiB using external PL based
+DDR memory:
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+/ {
+	reserved-memory {
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		ranges;
+		plmem_multimedia: multimedia_dma_mem_region {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x48 0x0 0x0 0x70000000>;
+		};
+	};
+};
+...
+	video_cap {
+		/* ... */
+		memory-region = <&plmem_multimedia>;
+	}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml
@@ -106,7 +106,6 @@
               - mediatek,mt2701-smi-larb
               - mediatek,mt2712-smi-larb
               - mediatek,mt6779-smi-larb
-              - mediatek,mt8167-smi-larb
               - mediatek,mt8192-smi-larb
 
     then:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/mfd/google,cros-ec.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/mfd/google,cros-ec.yaml
@@ -39,18 +39,14 @@
     description:
       This property specifies the delay in usecs between the
       assertion of the CS and the first clock pulse.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - default: 0
-      - minimum: 0
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
 
   google,cros-ec-spi-msg-delay:
     description:
       This property specifies the delay in usecs between messages.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - default: 0
-      - minimum: 0
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
 
   google,has-vbc-nvram:
     description:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml
@@ -50,15 +50,15 @@
     minimum: 0
     maximum: 1
 
-  rohm,charger-sense-resistor-ohms:
-    minimum: 10000000
-    maximum: 50000000
+  rohm,charger-sense-resistor-micro-ohms:
+    minimum: 10000
+    maximum: 50000
     description: |
-      BD71827 and BD71828 have SAR ADC for measuring charging currents.
-      External sense resistor (RSENSE in data sheet) should be used. If
-      something other but 30MOhm resistor is used the resistance value
-      should be given here in Ohms.
-    default: 30000000
+      BD71815 has SAR ADC for measuring charging currents. External sense
+      resistor (RSENSE in data sheet) should be used. If something other
+      but a 30 mOhm resistor is used the resistance value should be given
+      here in micro Ohms.
+    default: 30000
 
   regulators:
     $ref: ../regulator/rohm,bd71815-regulator.yaml
@@ -67,7 +67,7 @@
 
   gpio-reserved-ranges:
     description: |
-      Usage of BD71828 GPIO pins can be changed via OTP. This property can be
+      Usage of BD71815 GPIO pins can be changed via OTP. This property can be
       used to mark the pins which should not be configured for GPIO. Please see
       the ../gpio/gpio.txt for more information.
 
@@ -113,7 +113,7 @@
             gpio-controller;
             #gpio-cells = <2>;
 
-            rohm,charger-sense-resistor-ohms = <10000000>;
+            rohm,charger-sense-resistor-micro-ohms = <10000>;
 
             regulators {
                 buck1: buck1 {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/mfd/syscon.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -55,6 +55,7 @@
               - samsung,exynos4-sysreg
               - samsung,exynos5-sysreg
               - samsung,exynos5433-sysreg
+              - xlnx,zynqmp-dpaud-setting
 
           - const: syscon
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/jesd-phy.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/jesd-phy.txt
@@ -0,0 +1,24 @@
+* Xilinx JESD204B Phy
+
+Description:
+The LogiCORE™ IP JESD204 PHY core implements a JESD204B Physical interface supporting
+line rates between 1.0 and 12.5 Gb/s on 1 to 12 lanes using GTX, GTH, or GTP transceivers.
+
+Required properties:
+- compatible = "xlnx,jesd204-phy-2.0"
+- reg = Should contain JESD204B phy registers location and length
+- xlnx,pll-selection = The PLL selection 3 for QPLL and 1 For CPLL
+- xlnx,lanes = No of Lanes
+- xlnx,gt-refclk-freq = Reference frequency in Hz
+- clocks = The phandle to the clock tree
+
+Example:
+++++++++
+	jesd204_phycores:phy@41e10000 {
+		compatible = "xlnx,jesd204-phy-2.0";
+		reg = <0x41e10000 0x10000>;
+		xlnx,gt-refclk-freq = "156250000";
+		xlnx,lanes = <0x1>;
+		xlnx,pll-selection = <0x3>;
+		clocks = <&si570>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/jesd204b.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/jesd204b.txt
@@ -0,0 +1,28 @@
+* Xilinx JESD204B core
+
+Description:
+The LogiCORE™ IP JESD204 core implements a JESD204B core
+
+Required properties:
+- compatible = Should be one of
+		"xlnx,jesd204-5.1";
+		"xlnx,jesd204-5.2";
+		"xlnx,jesd204-6.1";
+- reg = Should contain JESD204B registers location and length
+- xlnx,frames-per-multiframe = No of frames per multiframe
+- xlnx,bytes-per-frame = No of bytes per frame
+- xlnx,lanes = No of Lanes
+- xlnx,subclass = subclass
+- xlnx,node-is-transmit = should be present only for transmit nodes
+
+Example:
+++++++++
+jesd_Tx_axi_0: jesd_Tx@44a20000 {
+	compatible = "xlnx,jesd204-5.1";
+	reg = <0x44a20000 0x10000>;
+	xlnx,frames-per-multiframe = <30>;
+	xlnx,bytes-per-frame = <2>;
+	xlnx,subclass = <1>;
+	xlnx,lanes = <0x2>;
+	xlnx,node-is-transmit;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/xlnx,axi-traffic-gen.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/xlnx,axi-traffic-gen.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/xlnx,axi-traffic-gen.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Axi Traffic generator Device Tree Bindings
+
+maintainers:
+  - shubhrajyoti.datta@xilinx.com
+
+properties:
+  compatible:
+    enum:
+      - xlnx,axi-traffic-gen
+      - xlnx,axi-traffic-gen-1.0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: err-out interrupt
+      - description: irq-out interrupt
+
+  interrupt-names:
+    items:
+      - const: err-out
+      - const: irq-out
+
+  clocks:
+    minItems: 1
+
+  xlnx,device-id:
+    description: Device instance id
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+
+additionalProperties: false
+
+examples:
+  - |
+    trafgen_0: trafgen@76000000 {
+        compatible = "xlnx,axi-traffic-gen";
+        clocks = <&clkc 15>;
+        interrupts = <0 93 4 >, < 0 94 4 >;
+        interrupt-parent = <&axi_intc_1>;
+        interrupt-names = "err-out", "irq-out";
+        reg = <0x76000000 0x800000>;
+        xlnx,device-id = <0x0>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/xlnx,dpu.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/xlnx,dpu.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/xlnx,dpu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Deep learning Processing Unit (DPU) Vivado Flow DT Bindings
+
+maintainers:
+  - Ye Yang <ye.yang@xilinx.com>
+
+description: |+
+    The DPUCZDX8G is the deep learning processing unit (DPU) designed to
+    support the Zynq UltraScale+ MPSoC. It is a configurable computation
+    engine optimized for convolutional neural networks.
+
+    The driver supports up to 4 DPU cores with 40-bit addressing and 1
+    softmax core with 32-bit addressing, depending on how the user config
+    the IP in Vivado TRD Flow.
+
+    For more details refer to PG338 "DPUCZDX8G for Zynq UltraScale+ MPSoCs"
+    (https://www.xilinx.com/content/dam/xilinx/support/documentation/ip_documentation/dpu/v3_4/pg338-dpu.pdf)
+
+properties:
+  compatible:
+    items:
+      - const: xlnx,dpuczdx8g-3.4
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: List of clock specifiers.
+    items:
+      - description: AXI Lite clock
+      - description: dsp clock, used for DSP blocks in the DPUCZDX8G. The frequency is twice that of dpu clock
+      - description: dpu clock, used for DPUCZDX8G general logic
+
+  clock-names:
+    items:
+      - const: s_axi_aclk
+      - const: dpu_2x_clk
+      - const: m_axi_dpu_aclk
+
+  interrupts:
+    description: One interrupt per available DPU core(up to 4) or 1 softmax core
+    minItems: 1
+    maxItems: 5
+
+  interrupt-names:
+    minItems: 1
+    maxItems: 5
+    items:
+      pattern: "^(dpu[0-3]|sfm)_interrupt$"
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+
+additionalProperties: false
+
+examples:
+  # Example for ZynqMP (2 DPU and 1 SOFTMAX)
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    dpuczdx8g@8f000000 {
+        compatible = "xlnx,dpuczdx8g-3.4";
+        reg = <0x8f000000 0x1000000>;
+        interrupt-parent = <&gic>;
+        interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "dpu0_interrupt", "dpu1_interrupt", "sfm_interrupt";
+        clocks = <&zynqmp_clk 71>, <&misc_clk_0>, <&misc_clk_1>;
+        clock-names = "s_axi_aclk", "dpu_2x_clk", "m_axi_dpu_aclk";
+    };
+
+  # Example for Microblaze (1 DPU)
+  - |
+    dpuczdx8g@1000000 {
+        compatible = "xlnx,dpuczdx8g-3.4";
+        reg = <0x01000000 0x1000000>;
+        interrupt-parent = <&microblaze_0_axi_intc>;
+        interrupts = <8 2>;
+        interrupt-names = "dpu0_interrupt";
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/xlnx,fclk.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/xlnx,fclk.txt
@@ -0,0 +1,12 @@
+* Xilinx fclk clock enable
+Temporary solution for enabling the PS_PL clocks.
+
+Required properties:
+- compatible: "xlnx,fclk"
+
+Example:
+++++++++
+fclk0: fclk0 {
+	compatible = "xlnx,fclk";
+	clocks = <&clkc 71>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/xlnx,tmr-inject.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/xlnx,tmr-inject.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/xlnx,tmr-inject.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx TMR Inject Device Tree Bindings
+
+maintainers:
+  - Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+
+description: |
+  The Triple Modular Redundancy(TMR) Inject core provides functional
+  fault injection by changing selected MicroBlaze instructions,
+  which provides the possibility to verify that the TMR
+  subsystem error detection and fault recovery logic
+  is working properly.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,tmr-inject-1.0
+
+  reg:
+    maxItems: 1
+
+  xlnx,magic:
+    description: |
+      Magic number used when injecting faults. The fault inject write
+      data least significant byte (bits 7:0) must match this number
+      to have any effect. The value shall be in the range 0-255.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+  - compatible
+  - reg
+  - xlnx,magic
+
+additionalProperties: false
+
+examples:
+  - |
+    tmr-inject@44a30000 {
+            compatible = "xlnx,tmr-inject-1.0";
+            reg = <0x44a10000 0x10000>;
+            xlnx,magic = <0x46>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/misc/xlnx,tmr-manager.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/misc/xlnx,tmr-manager.yaml
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/xlnx,tmr-manager.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx TMR Microblaze Device Tree Bindings
+
+maintainers:
+  - Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+
+description: |
+  The Triple Modular Redundancy(TMR) Manager is responsible
+  for handling the TMR subsystem state, including fault detection
+  and error recovery. The core is triplicated in each of the
+  sub-blocks in the TMR subsystem, and provides majority
+  voting of its internal state.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,tmr-manager-1.0
+
+  reg:
+    maxItems: 1
+
+  xlnx,magic1:
+    description:
+      Magic number 1, When writing to the control register the first
+      write data byte (bits 7:0) must match this value in order to
+      have any effect on the nominal recovery function. the value
+      shall be in the range 0-255.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+  - compatible
+  - reg
+  - xlnx,magic1
+
+additionalProperties: false
+
+examples:
+  - |
+    tmr-manager@44a10000 {
+            compatible = "xlnx,tmr-manager-1.0";
+            reg = <0x44a10000 0x10000>;
+            xlnx,magic1 = <0x46>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
@@ -25,7 +25,7 @@
   "#address-cells":
     const: 1
     description: |
-      The cell is the slot ID if a function subnode is used.
+      The cell is the SDIO function number if a function subnode is used.
 
   "#size-cells":
     const: 0
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -55,7 +55,7 @@
     properties:
       reg:
         description:
-          Contains the native Ready/Busy IDs.
+          Contains the chip-select IDs.
 
       nand-ecc-engine:
         allOf:
@@ -184,7 +184,7 @@
         nand-use-soft-ecc-engine;
         nand-ecc-algo = "bch";
 
-        /* controller specific properties */
+        /* NAND chip specific properties */
       };
 
       nand@1 {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml
@@ -96,8 +96,7 @@
 
       rockchip,boot-ecc-strength:
         enum: [16, 24, 40, 60, 70]
-        allOf:
-          - $ref: /schemas/types.yaml#/definitions/uint32
+        $ref: /schemas/types.yaml#/definitions/uint32
         description: |
           If specified it indicates that a different BCH/ECC setting is
           supported by the boot ROM.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
@@ -23,6 +23,7 @@
       - brcm,bcm4345c5
       - brcm,bcm43540-bt
       - brcm,bcm4335a0
+      - brcm,bcm4349-bt
 
   shutdown-gpios:
     maxItems: 1
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
@@ -31,7 +31,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		spi-max-frequency = <10000000>;
-		bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>;
+		bosch,mram-cfg = <0x0 0 0 16 0 0 1 1>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
 		device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/can/xilinx,can.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/can/xilinx,can.yaml
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/can/xilinx,can.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title:
+  Xilinx Axi CAN/Zynq CANPS controller
+
+maintainers:
+  - Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+
+properties:
+  compatible:
+    enum:
+      - xlnx,zynq-can-1.0
+      - xlnx,axi-can-1.00.a
+      - xlnx,canfd-1.0
+      - xlnx,canfd-2.0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+    maxItems: 2
+
+  clock-names:
+    maxItems: 2
+
+  power-domains:
+    maxItems: 1
+
+  tx-fifo-depth:
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    description: CAN Tx fifo depth (Zynq, Axi CAN).
+
+  rx-fifo-depth:
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    description: CAN Rx fifo depth (Zynq, Axi CAN, CAN FD in sequential Rx mode)
+
+  tx-mailbox-count:
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    description: CAN Tx mailbox buffer count (CAN FD)
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+allOf:
+  - $ref: can-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - xlnx,zynq-can-1.0
+
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: can_clk
+            - const: pclk
+      required:
+        - tx-fifo-depth
+        - rx-fifo-depth
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - xlnx,axi-can-1.00.a
+
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: can_clk
+            - const: s_axi_aclk
+      required:
+        - tx-fifo-depth
+        - rx-fifo-depth
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - xlnx,canfd-1.0
+              - xlnx,canfd-2.0
+
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: can_clk
+            - const: s_axi_aclk
+      required:
+        - tx-mailbox-count
+        - rx-fifo-depth
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    can@e0008000 {
+        compatible = "xlnx,zynq-can-1.0";
+        reg = <0xe0008000 0x1000>;
+        clocks = <&clkc 19>, <&clkc 36>;
+        clock-names = "can_clk", "pclk";
+        interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-parent = <&intc>;
+        tx-fifo-depth = <0x40>;
+        rx-fifo-depth = <0x40>;
+    };
+
+  - |
+    can@40000000 {
+        compatible = "xlnx,axi-can-1.00.a";
+        reg = <0x40000000 0x10000>;
+        clocks = <&clkc 0>, <&clkc 1>;
+        clock-names = "can_clk", "s_axi_aclk";
+        interrupt-parent = <&intc>;
+        interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>;
+        tx-fifo-depth = <0x40>;
+        rx-fifo-depth = <0x40>;
+    };
+
+  - |
+    can@40000000 {
+        compatible = "xlnx,canfd-1.0";
+        reg = <0x40000000 0x2000>;
+        clocks = <&clkc 0>, <&clkc 1>;
+        clock-names = "can_clk", "s_axi_aclk";
+        interrupt-parent = <&intc>;
+        interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>;
+        tx-mailbox-count = <0x20>;
+        rx-fifo-depth = <0x20>;
+    };
+
+  - |
+    can@ff060000 {
+        compatible = "xlnx,canfd-2.0";
+        reg = <0xff060000 0x6000>;
+        clocks = <&clkc 0>, <&clkc 1>;
+        clock-names = "can_clk", "s_axi_aclk";
+        interrupt-parent = <&intc>;
+        interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>;
+        tx-mailbox-count = <0x20>;
+        rx-fifo-depth = <0x40>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/cdns,macb.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/cdns,macb.yaml
@@ -0,0 +1,213 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/cdns,macb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence MACB/GEM Ethernet controller
+
+maintainers:
+  - Nicolas Ferre <nicolas.ferre@microchip.com>
+  - Claudiu Beznea <claudiu.beznea@microchip.com>
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - cdns,at91rm9200-emac  # Atmel at91rm9200 SoC
+          - const: cdns,emac          # Generic
+
+      - items:
+          - enum:
+              - cdns,zynq-gem         # Xilinx Zynq-7xxx SoC
+              - cdns,zynqmp-gem       # Xilinx Zynq Ultrascale+ MPSoC
+              - cdns,versal-gem       # Xilinx Versal
+          - const: cdns,gem           # Generic
+
+      - items:
+          - enum:
+              - cdns,at91sam9260-macb # Atmel at91sam9 SoCs
+              - cdns,sam9x60-macb     # Microchip sam9x60 SoC
+          - const: cdns,macb          # Generic
+
+      - items:
+          - enum:
+              - atmel,sama5d3-macb    # 10/100Mbit IP on Atmel sama5d3 SoCs
+          - enum:
+              - cdns,at91sam9260-macb # Atmel at91sam9 SoCs.
+          - const: cdns,macb          # Generic
+
+      - enum:
+          - atmel,sama5d29-gem        # GEM XL IP (10/100) on Atmel sama5d29 SoCs
+          - atmel,sama5d2-gem         # GEM IP (10/100) on Atmel sama5d2 SoCs
+          - atmel,sama5d3-gem         # Gigabit IP on Atmel sama5d3 SoCs
+          - atmel,sama5d4-gem         # GEM IP (10/100) on Atmel sama5d4 SoCs
+          - cdns,at32ap7000-macb      # Other 10/100 usage or use the generic form
+          - cdns,np4-macb             # NP4 SoC devices
+          - microchip,sama7g5-emac    # Microchip SAMA7G5 ethernet interface
+          - microchip,sama7g5-gem     # Microchip SAMA7G5 gigabit ethernet interface
+          - sifive,fu540-c000-gem     # SiFive FU540-C000 SoC
+          - cdns,emac                 # Generic
+          - cdns,gem                  # Generic
+          - cdns,macb                 # Generic
+
+  reg:
+    minItems: 1
+    items:
+      - description: Basic register set
+      - description: GEMGXL Management block registers on SiFive FU540-C000 SoC
+
+  interrupts:
+    minItems: 1
+    maxItems: 8
+    description: One interrupt per available hardware queue
+
+  clocks:
+    minItems: 1
+    maxItems: 5
+
+  clock-names:
+    minItems: 1
+    items:
+      - enum: [ ether_clk, hclk, pclk ]
+      - enum: [ hclk, pclk ]
+      - const: tx_clk
+      - enum: [ rx_clk, tsu_clk ]
+      - const: tsu_clk
+
+  local-mac-address: true
+
+  phy-mode: true
+
+  phy-handle: true
+
+  phys:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description:
+      Recommended with ZynqMP, specify reset control for this
+      controller instance with zynqmp-reset driver.
+
+  reset-names:
+    maxItems: 1
+
+  fixed-link: true
+
+  iommus:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  rx-watermark:
+    description:
+      Set watermark value for pbuf_rxcutthru reg and enable rx partial store
+      and forward, only when compatible = "cdns,zynqmp-gem"
+    maximum: 0xFF
+  mdio:
+    type: object
+    description:
+      Node containing PHY children. If this node is not present, then PHYs will
+      be direct children.
+
+patternProperties:
+  "^ethernet-phy@[0-9a-f]$":
+    type: object
+    $ref: ethernet-phy.yaml#
+
+    properties:
+      reset-gpios: true
+
+      magic-packet:
+        description:
+          Indicates that the hardware supports waking up via magic packet.
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - phy-mode
+
+allOf:
+  - $ref: ethernet-controller.yaml#
+
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              const: sifive,fu540-c000-gem
+    then:
+      properties:
+        reg:
+          maxItems: 1
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    macb0: ethernet@fffc4000 {
+            compatible = "cdns,at32ap7000-macb";
+            reg = <0xfffc4000 0x4000>;
+            interrupts = <21>;
+            phy-mode = "rmii";
+            local-mac-address = [3a 0e 03 04 05 06];
+            clock-names = "pclk", "hclk", "tx_clk";
+            clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            ethernet-phy@1 {
+                    reg = <0x1>;
+                    reset-gpios = <&pioE 6 1>;
+            };
+    };
+
+  - |
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+    #include <dt-bindings/power/xlnx-zynqmp-power.h>
+    #include <dt-bindings/reset/xlnx-zynqmp-resets.h>
+    #include <dt-bindings/phy/phy.h>
+
+    bus {
+            #address-cells = <2>;
+            #size-cells = <2>;
+            gem1: ethernet@ff0c0000 {
+                    compatible = "cdns,zynqmp-gem", "cdns,gem";
+                    interrupt-parent = <&gic>;
+                    interrupts = <0 59 4>, <0 59 4>;
+                    reg = <0x0 0xff0c0000 0x0 0x1000>;
+                    clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>,
+                             <&zynqmp_clk GEM1_TX>, <&zynqmp_clk GEM1_RX>,
+                             <&zynqmp_clk GEM_TSU>;
+                    clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    #stream-id-cells = <1>;
+                    iommus = <&smmu 0x875>;
+                    power-domains = <&zynqmp_firmware PD_ETH_1>;
+                    resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>;
+                    reset-names = "gem1_rst";
+                    status = "okay";
+                    phy-mode = "sgmii";
+                    phys = <&psgtr 1 PHY_TYPE_SGMII 1 1>;
+                    fixed-link {
+                            speed = <1000>;
+                            full-duplex;
+                            pause;
+                    };
+            };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/ethernet-phy.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/ethernet-phy.yaml
@@ -91,6 +91,14 @@
       compensate for the board being designed with the lanes
       swapped.
 
+  enet-phy-lane-no-swap:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      If set, indicates that PHY will disable swap of the
+      TX/RX lanes. This property allows the PHY to work correcly after
+      e.g. wrong bootstrap configuration caused by issues in PCB
+      layout design.
+
   eee-broken-100tx:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
@@ -33,7 +33,14 @@
 			  VSC8531_DUPLEX_COLLISION (8).
 - load-save-gpios	: GPIO used for the load/save operation of the PTP
 			  hardware clock (PHC).
-
+- vsc8531,rx-delay	: RGMII RX delay. Allowed values are defined in
+			  "include/dt-bindings/net/mscc-phy-vsc8531.h".
+			  Default value, set by the driver is
+			  VSC8531_RGMII_CLK_DELAY_1_1_NS.
+- vsc8531,tx-delay	: RGMII TX delay. Allowed values are defined in
+			  "include/dt-bindings/net/mscc-phy-vsc8531.h".
+			  Default value, set by the driver is
+			  VSC8531_RGMII_CLK_DELAY_0_2_NS.
 
 Table: 1 - Edge rate change
 ----------------------------------------------------------------|
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/qcom,ipa.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/qcom,ipa.yaml
@@ -106,6 +106,10 @@
           - const: imem
           - const: config
 
+  qcom,qmp:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to the AOSS side-channel message RAM
+
   qcom,smem-states:
     $ref: /schemas/types.yaml#/definitions/phandle-array
     description: State bits used in by the AP to signal the modem.
@@ -221,6 +225,8 @@
                                      "imem",
                                      "config";
 
+                qcom,qmp = <&aoss_qmp>;
+
                 qcom,smem-states = <&ipa_smp2p_out 0>,
                                    <&ipa_smp2p_out 1>;
                 qcom,smem-state-names = "ipa-clock-enabled-valid",
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/snps,dwmac.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/snps,dwmac.yaml
@@ -53,20 +53,18 @@
         - allwinner,sun8i-r40-emac
         - allwinner,sun8i-v3s-emac
         - allwinner,sun50i-a64-emac
-        - loongson,ls2k-dwmac
-        - loongson,ls7a-dwmac
         - amlogic,meson6-dwmac
         - amlogic,meson8b-dwmac
         - amlogic,meson8m2-dwmac
         - amlogic,meson-gxbb-dwmac
         - amlogic,meson-axg-dwmac
-        - loongson,ls2k-dwmac
-        - loongson,ls7a-dwmac
         - ingenic,jz4775-mac
         - ingenic,x1000-mac
         - ingenic,x1600-mac
         - ingenic,x1830-mac
         - ingenic,x2000-mac
+        - loongson,ls2k-dwmac
+        - loongson,ls7a-dwmac
         - rockchip,px30-gmac
         - rockchip,rk3128-gmac
         - rockchip,rk3228-gmac
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml
@@ -88,8 +88,7 @@
         type: object
         description: CPSW external ports
 
-        allOf:
-          - $ref: ethernet-controller.yaml#
+        $ref: ethernet-controller.yaml#
 
         properties:
           reg:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/xilinx-phy.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/xilinx-phy.txt
@@ -0,0 +1,15 @@
+Xilinx PCS/PMA PHY bindings
+
+Required properties:
+	- reg - The ID number for the phy, usually a small integer
+
+Optional properties:
+	- xlnx,phy-type - Describes type 1000BaseX (set to 0x5) or
+			  SGMII (set to 0x4)
+
+Example:
+
+	ethernet-phy@9 {
+		reg = <9>;
+		xlnx,phy-type = <0x5>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/xilinx_axienet.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/xilinx_axienet.txt
@@ -1,34 +1,59 @@
 XILINX AXI ETHERNET Device Tree Bindings
 --------------------------------------------------------
 
-Also called  AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
-provides connectivity to an external ethernet PHY supporting different
-interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
-segments of memory for buffering TX and RX, as well as the capability of
-offloading TX/RX checksum calculation off the processor.
+This driver supports following MAC configurations-
+a) AXI 1G/2.5G Ethernet Subsystem.
+b) 10G/25G High Speed Ethernet Subsystem.
+c) 10 Gigabit Ethernet Subsystem.
+d) USXGMII Ethernet Subsystem.
+e) MRMAC Ethernet Subsystem.
+
+AXI 1G/2.5G Ethernet Subsystem- also called  AXI 1G/2.5G Ethernet Subsystem,
+the xilinx axi ethernet IP core provides connectivity to an external ethernet
+PHY supporting different interfaces: MII, GMII, RGMII, SGMII, 1000BaseX.
+It also includes two segments of memory for buffering TX and RX, as well as
+the capability of offloading TX/RX checksum calculation off the processor.
 
 Management configuration is done through the AXI interface, while payload is
 sent and received through means of an AXI DMA controller. This driver
 includes the DMA driver code, so this driver is incompatible with AXI DMA
 driver.
 
-For more details about mdio please refer phy.txt file in the same directory.
+MRMAC is a hardened Ethernet IP on Versal supporting multiple rates from
+10G to 100G which can be used with a soft DMA controller.
+
+For details about MDIO please refer phy.txt [1].
 
 Required properties:
-- compatible	: Must be one of "xlnx,axi-ethernet-1.00.a",
-		  "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a"
+- compatible	: Must be one of "xlnx,axi-ethernet-1.00.a" or
+		  "xlnx,axi-ethernet-1.01.a" or "xlnx,axi-ethernet-2.01.a"
+		  for 1G MAC,
+		  "xlnx,ten-gig-eth-mac" for 10 Gigabit Ethernet Subsystem,
+		  "xlnx,xxv-ethernet-1.0" for 10G/25G MAC,
+		  "xlnx,axi-2_5-gig-ethernet-1.0" for 2.5G MAC,
+		  "xlnx,xxv-usxgmii-ethernet-1.0" for USXGMII and
+		  "xlnx,mrmac-ethernet-1.0" for MRMAC.
 - reg		: Address and length of the IO space, as well as the address
                   and length of the AXI DMA controller IO space, unless
                   axistream-connected is specified, in which case the reg
                   attribute of the node referenced by it is used.
 - interrupts	: Should be a list of 2 or 3 interrupts: TX DMA, RX DMA,
-		  and optionally Ethernet core. If axistream-connected is
-		  specified, the TX/RX DMA interrupts should be on that node
-		  instead, and only the Ethernet core interrupt is optionally
-		  specified here.
+		  and optionally Ethernet core.
 - phy-handle	: Should point to the external phy device.
 		  See ethernet.txt file in the same directory.
 - xlnx,rxmem	: Set to allocated memory buffer for Rx/Tx in the hardware
+Required properties (When AxiEthernet is configured with MCDMA):
+- xlnx,channel-ids	: Queue Identifier associated with the MCDMA Channel.
+- interrupt-names	: Should contain the interrupt names.
+
+Required properties when configured as MRMAC:
+- xlnx,mrmac-rate	: Can be 10000 or 25000 providing rate in Mbps.
+- xlnx,gtlane		: Indicate the GT reset and speed control lane for the
+			  the current MRMAC lane. Valid range is 0 to 3.
+- xlnx,gtpll		: Handle to AXI GPIO instance for GT PLL mask control.
+			  This is required to control the common PLL mask bits.
+- xlnx,gtctrl		: Handle to AXI GPIO instance for GT speed and reset
+			  control for each MRMAC lane.
 
 Optional properties:
 - phy-mode	: See ethernet.txt
@@ -38,56 +63,106 @@
 		  1 to enable partial TX checksum offload,
 		  2 to enable full TX checksum offload
 - xlnx,rxcsum	: Same values as xlnx,txcsum but for RX checksum offload
-- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to
-		  support both 1000BaseX and SGMII modes. If set, the phy-mode
-		  should be set to match the mode selected on core reset (i.e.
-		  by the basex_or_sgmii core input line).
-- clock-names: 	  Tuple listing input clock names. Possible clocks:
-		  s_axi_lite_clk: Clock for AXI register slave interface
-		  axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces
-		  ref_clk: Ethernet reference clock, used by signal delay
-			   primitives and transceivers
-		  mgt_clk: MGT reference clock (used by optional internal
-			   PCS/PMA PHY)
-
-		  Note that if s_axi_lite_clk is not specified by name, the
-		  first clock of any name is used for this. If that is also not
-		  specified, the clock rate is auto-detected from the CPU clock
-		  (but only on platforms where this is possible). New device
-		  trees should specify all applicable clocks by name - the
-		  fallbacks to an unnamed clock or to CPU clock are only for
-		  backward compatibility.
-- clocks: 	  Phandles to input clocks matching clock-names. Refer to common
-		  clock bindings.
-- axistream-connected: Reference to another node which contains the resources
-		       for the AXI DMA controller used by this device.
-		       If this is specified, the DMA-related resources from that
-		       device (DMA registers and DMA TX/RX interrupts) rather
-		       than this one will be used.
+- clocks		: Input clock specifier. Refer to common clock bindings.
+- clock-names		: Input clock names. Refer to IP PG for signal description.
+			  1G/2.5G: s_axi_lite_clk, axis_clk and ref_clk.
+			  10G/25G and USXGMII: s_axi_aclk, rx_core_clk and dclk.
+			  10 Gigabit: s_axi_aclk and dclk.
+			  AXI DMA and MCDMA: m_axi_sg_aclk, m_axi_mm2s_aclk and
+			  m_axi_s2mm_aclk.
  - mdio		: Child node for MDIO bus. Must be defined if PHY access is
 		  required through the core's MDIO interface (i.e. always,
 		  unless the PHY is accessed through a different bus).
+- dma-coherent		: Present if dma operations are coherent.
+- xlnx,eth-hasnobuf	: Used when 1G MAC is configured in non-processor mode.
+- xlnx,rxtsfifo		: Configures the axi fifo for receive timestamping.
+
+Optional properties for connected DMA node:
+- xlnx,addrwidth	: Specify the width of the DMA address space in bits.
+			  Value type is u8. Valid range is 32-64. Default is 32.
+- xlnx,include-dre	: Tells whether DMA h/w is configured with data
+			  realignment engine(DRE) or not.
+
+Optional properties (When USXGMII is in use):
+- xlnx,usxgmii-rate	: USXGMII PHY speed - can be 10, 100, 1000, 2500,
+			  5000 or 10000.
+
+Optional properties (When AxiEthernet is configured with MCDMA):
+- xlnx,num-queues	: Number of queues h/w configured for.
+
+Optional properties for MRMAC:
+- xlnx,phcindex		: Indicate the index of the physical hardware clock
+			  to be used as per PTP clock connected to the given
+			  MRMAC lane. Valid range is 0 to 3.
+
+NOTE: Time Sensitive Networking (TSN) related DT bindings are explained in [4].
+
+[1] Documentation/devicetree/bindings/net/phy.txt
+[2] Documentation/devicetree/bindings/net/ethernet.txt
+[3] Documentation/devicetree/bindings/net/xilinx-phy.txt
+[4] Documentation/devicetree/bindings/net/xilinx_tsn.txt
+
+
+Example: AXI 1G/2.5G Ethernet Subsystem + AXIDMA
+
+	axi_eth_0_dma: dma@80040000 {
+			#dma-cells = <1>;
+			compatible = "xlnx,eth-dma";
+			xlnx,addrwidth = /bits/ 8 <32>;
+			<snip>
+	};
 
-Example:
-	axi_ethernet_eth: ethernet@40c00000 {
-		compatible = "xlnx,axi-ethernet-1.00.a";
-		device_type = "network";
-		interrupt-parent = <&microblaze_0_axi_intc>;
-		interrupts = <2 0 1>;
-		clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
-		clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
-		phy-mode = "mii";
-		reg = <0x40c00000 0x40000 0x50c00000 0x40000>;
-		xlnx,rxcsum = <0x2>;
-		xlnx,rxmem = <0x800>;
-		xlnx,txcsum = <0x2>;
-		phy-handle = <&phy0>;
-		axi_ethernetlite_0_mdio: mdio {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			phy0: phy@0 {
-				device_type = "ethernet-phy";
-				reg = <1>;
+	axi_eth_0: ethernet@80000000 {
+			axistream-connected = <&axi_eth_0_dma>;
+			compatible = "xlnx,axi-ethernet-1.00.a";
+			device_type = "network";
+			interrupt-names = "interrupt";
+			interrupt-parent = <&gic>;
+			interrupts = <0 91 4>;
+			phy-handle = <&phy2>;
+			phy-mode = "sgmii";
+			reg = <0x0 0x80000000 0x0 0x40000>;
+			xlnx,include-dre ;
+			xlnx,phy-type = <0x5>;
+			xlnx,rxcsum = <0x0>;
+			xlnx,rxmem = <0x1000>;
+			xlnx,txcsum = <0x0>;
+			axi_eth_0_mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy2: phy@2 {
+					device_type = "ethernet-phy";
+					reg = <2>;
+				};
 			};
-		};
+	};
+
+Example for MRMAC Ethernet subsystem with MCDMA:
+	axi_mcdma_0: axi_mcdma@a4050000 {
+			#dma-cells = <1>;
+			compatible = "xlnx,axi-mcdma-1.1";
+			xlnx,addrwidth = <0x20>;
+			xlnx,include-dre;
+			<snip>
+	};
+
+	gt_pll: gpio@a4000000 {
+		reg = <0x0 0xa4000000 0x0 0x10000>;
+		<snip>
+	}
+
+	gt_ctrl: gpio@a4010000 {
+		reg = <0x0 0xa4010000 0x0 0x40000>;
+		<snip>
+	};
+
+	mrmac_0: mrmac@80000000 {
+		axistream-connected = <&axi_mcdma_0>;
+		compatible = "xlnx,mrmac-ethernet-1.0";
+		reg = <0x0 0xa4090000 0x0 0x1000>;
+		xlnx,mrmac-rate = <10000>;
+		xlnx,gtpll = <&gt_pll>;
+		xlnx,gtctrl = <&gt_ctrl>;
+		xlnx,gtlane = <0x0>;
+		xlnx,rxmem = <0x8000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/net/xilinx_emaclite.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/net/xilinx_emaclite.txt
@@ -0,0 +1,35 @@
+Xilinx Axi Ethernetlite controller Device Tree Bindings
+---------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,opb-ethernetlite-1.01.a" or
+			  "xlnx,opb-ethernetlite-1.01.b" or
+			  "xlnx,opb-ethernetlite-1.00.a" or
+			  "xlnx,xps-ethernetlite-2.00.a" or
+			  "xlnx,xps-ethernetlite-2.01.a" or
+			  "xlnx,xps-ethernetlite-3.00.a" or.
+- reg			: Physical base address and size of the Axi ethernetlite
+			  registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupt-parent	: Must be core interrupt controller.
+- phy-handle		: See ethernet.txt file in the same directory.
+
+Optional properties:
+- local-mac-address	: See ethernet.txt file in the same directory.
+			  If absent, random mac address is selected.
+- xlnx,tx-ping-pong	: If present, hardware supports tx ping pong buffer.
+- xlnx,rx-ping-pong	: If present, hardware supports rx ping pong buffer.
+
+Example:
+	axi_ethernetlite_1: ethernet@40e00000 {
+                        compatible = "xlnx,axi-ethernetlite-3.0", "xlnx,xps-ethernetlite-1.00.a";
+                        device_type = "network";
+                        interrupt-parent = <&axi_intc_1>;
+                        interrupts = <1 0>;
+                        local-mac-address = [00 0a 35 00 00 00];
+                        phy-handle = <&phy0>;
+                        reg = <0x40e00000 0x10000>;
+                        xlnx,rx-ping-pong;
+                        xlnx,tx-ping-pong;
+	}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/nvmem/mxs-ocotp.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/nvmem/mxs-ocotp.yaml
@@ -14,9 +14,11 @@
 
 properties:
   compatible:
-    enum:
-      - fsl,imx23-ocotp
-      - fsl,imx28-ocotp
+    items:
+      - enum:
+          - fsl,imx23-ocotp
+          - fsl,imx28-ocotp
+      - const: fsl,ocotp
 
   "#address-cells":
     const: 1
@@ -40,7 +42,7 @@
 examples:
   - |
     ocotp: efuse@8002c000 {
-        compatible = "fsl,imx28-ocotp";
+        compatible = "fsl,imx28-ocotp", "fsl,ocotp";
         #address-cells = <1>;
         #size-cells = <1>;
         reg = <0x8002c000 0x2000>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/nvmem/xlnx,versal-sec-cfg.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/nvmem/xlnx,versal-sec-cfg.yaml
@@ -0,0 +1,148 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/xlnx,versal-sec-cfg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Secure Configuration driver binding
+
+description: |
+  The versal_sec_cfg node provides access to the BBRAM keys,
+  BBRAM user data and volatile user keys by using the firmware interface.
+
+maintainers:
+  - Harsha <harshah@xilinx.com>
+
+allOf:
+  - $ref: "nvmem.yaml#"
+
+properties:
+  compatible:
+    const: xlnx,versal-sec-cfg
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 1
+
+patternProperties:
+  "^bbram-zeroize@4$":
+    type: object
+    description:
+      Initiates zeroization of BBRAM AES key. Write-only.
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+  "^bbram-key@10$":
+    type: object
+    description:
+      256-bit BBRAM AES key. Write-only.
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+  "^bbram-usr@30$":
+    type: object
+    description:
+      32-bit BBRAM user data space. Read and Write is supported.
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+  "^bbram-lock@48$":
+    type: object
+    description:
+      Lock register for upper 32 bits of the BBRAM. Write-only
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+  "^user-key@1[1,3,5,7,9,b,d,f,B,D,F]0$":
+    type: object
+    description:
+      Eight volatile user keys, Size can be 128-bits or 256-bits.
+      All are write-only.
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    versal-sec-cfg {
+      compatible = "xlnx,versal-sec-cfg";
+      #address-cells = <1>;
+      #size-cells = <1>;
+
+      bbram_zeroize: bbram-zeroize@4 {
+        reg = <0x4 0x4>;
+      };
+
+      bbram_key: bbram-key@10 {
+        reg = <0x10 0x20>;
+      };
+
+      bbram_usr: bbram-usr@30 {
+        reg = <0x30 0x4>;
+      };
+
+      bbram_lock: bbram-lock@48 {
+        reg = <0x48 0x4>;
+      };
+
+      user_key0: user-key@110 {
+        reg = <0x110 0x20>;
+      };
+
+      user_key1: user-key@130 {
+        reg = <0x130 0x20>;
+      };
+
+      user_key2: user-key@150 {
+        reg = <0x150 0x20>;
+      };
+
+      user_key3: user-key@170 {
+        reg = <0x170 0x20>;
+      };
+
+      user_key4: user-key@190 {
+       reg = <0x190 0x20>;
+      };
+
+      user_key5: user-key@1b0 {
+        reg = <0x1b0 0x20>;
+      };
+
+      user_key6: user-key@1d0 {
+        reg = <0x1d0 0x20>;
+      };
+
+      user_key7: user-key@1f0 {
+        reg = <0x1f0 0x20>;
+      };
+    };
+
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/nvmem/xlnx,zynqmp-nvmem.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/nvmem/xlnx,zynqmp-nvmem.txt
@@ -25,9 +25,78 @@
 			#size-cells = <1>;
 
 			/* Data cells */
-			soc_revision: soc_revision {
+			soc_revision: soc_revision@0 {
 				reg = <0x0 0x4>;
 			};
+			/*
+			* efuse memory access:
+			* all the efuse feilds need to be read
+			* with the exact size specified in the node
+			*/
+			/* DNA */
+			efuse_dna: efuse_dna@c {
+				reg = <0xc 0xc>;
+			};
+			/* User 0 */
+			efuse_usr0: efuse_usr0@20 {
+				reg = <0x20 0x4>;
+			};
+			/* User 1 */
+			efuse_usr1: efuse_usr1@24 {
+				reg = <0x24 0x4>;
+			};
+			/* User 2 */
+			efuse_usr2: efuse_usr2@28 {
+				reg = <0x28 0x4>;
+			};
+			/* User 3 */
+			efuse_usr3: efuse_usr3@2c {
+				reg = <0x2c 0x4>;
+			};
+			/* User 4 */
+			efuse_usr4: efuse_usr4@30 {
+				reg = <0x30 0x4>;
+			};
+			/* User 5 */
+			efuse_usr5: efuse_usr5@34 {
+				reg = <0x34 0x4>;
+			};
+			/* User 6 */
+			efuse_usr6: efuse_usr6@38 {
+				reg = <0x38 0x4>;
+			};
+			/* User 7 */
+			efuse_usr7: efuse_usr7@3c {
+				reg = <0x3c 0x4>;
+			};
+			/* Misc user control bits */
+			efuse_miscusr: efuse_miscusr@40 {
+				reg = <0x40 0x4>;
+			};
+			/* PUF chash */
+			efuse_chash: efuse_chash@50 {
+				reg = <0x50 0x4>;
+			};
+			/* PUF misc */
+			efuse_pufmisc: efuse_pufmisc@54 {
+				reg = <0x54 0x4>;
+			};
+			/* SEC_CTRL */
+			efuse_sec: efuse_sec@58 {
+				reg = <0x58 0x4>;
+			};
+			/* SPK ID */
+			efuse_spkid: efuse_spkid@5c {
+				reg = <0x5c 0x4>;
+			};
+			/* PPK0 hash */
+			efuse_ppk0hash: efuse_ppk0hash@a0 {
+				reg = <0xa0 0x30>;
+			};
+			/* PPK1 hash */
+			efuse_ppk1hash: efuse_ppk1hash@d0 {
+				reg = <0xd0 0x30>;
+			};
 		};
 	};
 };
@@ -44,3 +113,22 @@
 
 		...
 	};
+
+To program efuse memory, one should request specified bytes of size as below,
+NOTE: Efuse bits once programmed cannot be reverted.
+
+	- | TYPE	| OFFSET | SIZE(bytes)	|
+	- |User-0	| 0x20	 | 0x4		|
+	- |User-1	| 0x24	 | 0x4		|
+	- |User-2	| 0x28	 | 0x4		|
+	- |User-3	| 0x2C	 | 0x4		|
+	- |User-4	| 0x30	 | 0x4		|
+	- |User-5	| 0x34	 | 0x4		|
+	- |User-6	| 0x38	 | 0x4		|
+	- |User-7	| 0x3c	 | 0x4		|
+	- |Misc User	| 0x40	 | 0x4		|
+	- |SEC_CTRL	| 0x58	 | 0x4		|
+	- |SPK ID 	| 0x5C	 | 0x4		|
+	- |AES KEY 	| 0x60	 | 0x20		|
+	- |PPK0 hash	| 0xA0	 | 0x30		|
+	- |PPK1 hash	| 0xD0	 | 0x30		|
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -14,9 +14,6 @@
   This PCIe host controller is based on the Synopsys DesignWare PCIe IP
   and thus inherits all the common properties defined in snps,dw-pcie.yaml.
 
-allOf:
-  - $ref: /schemas/pci/snps,dw-pcie.yaml#
-
 properties:
   compatible:
     enum:
@@ -59,7 +56,7 @@
       - const: pcie
       - const: pcie_bus
       - const: pcie_phy
-      - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie
+      - enum: [ pcie_inbound_axi, pcie_aux ]
 
   num-lanes:
     const: 1
@@ -166,6 +163,47 @@
   - clocks
   - clock-names
 
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx6sx-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - {}
+            - {}
+            - {}
+            - const: pcie_inbound_axi
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx8mq-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - {}
+            - {}
+            - {}
+            - const: pcie_aux
+  - if:
+      properties:
+        compatible:
+          not:
+            contains:
+              enum:
+                - fsl,imx6sx-pcie
+                - fsl,imx8mq-pcie
+    then:
+      properties:
+        clock-names:
+          maxItems: 3
+
 unevaluatedProperties: false
 
 examples:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pci/rcar-pci-host.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pci/rcar-pci-host.yaml
@@ -68,6 +68,18 @@
   phy-names:
     const: pcie
 
+  vpcie1v5-supply:
+    description: The 1.5v regulator to use for PCIe.
+
+  vpcie3v3-supply:
+    description: The 3.3v regulator to use for PCIe.
+
+  vpcie12v-supply:
+    description: The 12v regulator to use for PCIe.
+
+  iommu-map: true
+  iommu-map-mask: true
+
 required:
   - compatible
   - reg
@@ -121,5 +133,7 @@
              clock-names = "pcie", "pcie_bus";
              power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
              resets = <&cpg 319>;
+             vpcie3v3-supply = <&pcie_3v3>;
+             vpcie12v-supply = <&pcie_12v>;
          };
     };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
@@ -36,7 +36,7 @@
       - const: mpu
 
   interrupts:
-    maxItems: 1
+    maxItems: 2
 
   clocks:
     items:
@@ -94,8 +94,9 @@
             #interrupt-cells = <1>;
             ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000>,
                      <0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>;
-            interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
-            interrupt-names = "intr";
+            interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "msi", "intr";
             interrupt-map-mask = <0 0 0 7>;
             interrupt-map =
                 <0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pci/xilinx-xdma-pl-pcie.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pci/xilinx-xdma-pl-pcie.txt
@@ -0,0 +1,121 @@
+* Xilinx XDMA PL PCIe Root Port Bridge DT description
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+- compatible: Should contain "xlnx,xdma-host-3.00"
+- reg: Should contain XDMA PCIe registers location and length
+- device_type: must be "pci"
+- interrupts: Should contain AXI PCIe interrupt
+- interrupt-map-mask,
+  interrupt-map: standard PCI properties to define the mapping of the
+	PCI interface to interrupt numbers.
+- ranges: ranges for the PCI memory regions (I/O space region is not
+	supported by hardware)
+	Please refer to the standard PCI bus binding document for a more
+	detailed explanation
+
+For MSI DECODE mode:
+- interrupt-names: Must include the following entries:
+	"misc": interrupt asserted when legacy or error interrupt is received
+	"msi1, msi0": interrupt asserted when an MSI is received
+
+Interrupt controller child node
++++++++++++++++++++++++++++++++
+Required properties:
+- interrupt-controller: identifies the node as an interrupt controller
+- #address-cells: specifies the number of cells needed to encode an
+	address. The value must be 0.
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+
+NOTE:
+The core provides a single interrupt for both INTx/MSI messages. So,
+created a interrupt controller node to support 'interrupt-map' DT
+functionality.  The driver will create an IRQ domain for this map, decode
+the four INTx interrupts in ISR and route them to this domain.
+
+
+Example:
+++++++++
+MSI FIFO mode:
+	xdma_0: axi-pcie@a0000000 {
+		#address-cells = <3>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		compatible = "xlnx,xdma-host-3.00";
+		device_type = "pci";
+		interrupt-map = <0 0 0 1 &pcie_intc_0 1>,
+				<0 0 0 2 &pcie_intc_0 2>,
+				<0 0 0 3 &pcie_intc_0 3>,
+				<0 0 0 4 &pcie_intc_0 4>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 89 4>;
+		ranges = <0x02000000 0x00000000 0xB0000000 0x0 0xB0000000 0x00000000 0x01000000>,
+			<0x43000000 0x00000005 0x00000000 0x00000005 0x00000000 0x00000000 0x01000000>;
+		reg = <0x0 0xA0000000 0x0 0x10000000>;
+		pcie_intc_0: interrupt-controller {
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller ;
+		};
+	};
+
+MSI DECODE mode:
+	xdma_0: axi-pcie@a0000000 {
+		#address-cells = <3>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		compatible = "xlnx,xdma-host-3.00";
+		device_type = "pci";
+		interrupt-map = <0 0 0 1 &pcie_intc_0 1>, <0 0 0 2 &pcie_intc_0 2>, <0 0 0 3 &pcie_intc_0 3>, <0 0 0 4 &pcie_intc_0 4>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-parent = <&gic>;
+		interrupt-names = "misc", "msi0", "msi1";
+		interrupts = <0 89 4>, <0 90 4>, <0 91 4>;
+		ranges = <0x02000000 0x00000000 0xB0000000 0x0 0xB0000000 0x00000000 0x01000000>,
+			<0x43000000 0x00000005 0x00000000 0x00000005 0x00000000 0x00000000 0x01000000>;
+		reg = <0x0 0xA0000000 0x0 0x10000000>;
+		pcie_intc_0: interrupt-controller {
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller ;
+		};
+	};
+
+Versal PL PCIe host Bridge DT description.
+
+The properties and their meanings are identical to those described in
+above Xilinx XDMA PL PCIe Root Port Bridge description.
+The IP supports only MSI DECODE mode.
+
+Properties that differ are:
+- compatible: Should contain "xlnx,pcie-dma-versal-2.0"
+
+Example:
+	pcie_dma_versal_0: axi-pcie@80000000 {
+		#address-cells = <3>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		compatible = "xlnx,pcie-dma-versal-2.0";
+		device_type = "pci";
+		interrupt-map = <0 0 0 1 &psv_pcie_intc_0 1>,
+				<0 0 0 2 &psv_pcie_intc_0 2>,
+				<0 0 0 3 &psv_pcie_intc_0 3>,
+				<0 0 0 4 &psv_pcie_intc_0 4>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-names = "misc", "msi0", "msi1";
+		interrupt-parent = <&gic>;
+		interrupts = <0 84 4 0 85 4 0 86 4>;
+		ranges = <0x02000000 0x00000000 0xB0000000 0x0 0xB0000000 0x00000000 0x10000000>,
+			 <0x43000000 0x00000005 0x00000000 0x00000005 0x00000000 0x00000000 0x01000000>;
+		reg = <0x0 0x80000000 0x0 0x10000000>;
+		psv_pcie_intc_0: interrupt-controller {
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller ;
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/perf/xilinx-apm.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/perf/xilinx-apm.yaml
@@ -0,0 +1,137 @@
+# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/perf/xilinx-apm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Axi Performance Monitor device tree bindings
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,axi-perf-monitor
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  xlnx,enable-profile:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1]
+    description:
+      Enables the profile mode.
+    maxItems: 1
+
+  xlnx,enable-trace:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1]
+    description:
+      Enables trace mode.
+    maxItems: 1
+
+  xlnx,num-monitor-slots:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 1
+      - maximum: 8
+    description:
+      Number of monitor slots.
+
+  xlnx,enable-event-count:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1]
+    description:
+      Enable event count.
+
+  xlnx,enable-event-log:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1]
+    description:
+      Enable event log.
+
+  xlnx,have-sampled-metric-cnt:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Sampled metric counters enabled in APM.
+
+  xlnx,metric-count-width:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [32, 64]
+    description:
+      Metric Counter width.
+
+  xlnx,metric-count-scale:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4, 8]
+    description:
+      Metric Counter scale factor.
+
+  xlnx,num-of-counters:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Number of counters in APM.
+
+  xlnx,metrics-sample-count-width:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [32, 64]
+    description:
+      Sampled metric counter width.
+
+  xlnx,global-count-width:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [32, 64]
+    description:
+      Global Clock counter width.
+
+  xlnx,id-filter-32bit:
+    description: APM is in 32-bit mode.
+    type: boolean
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    apm@44a00000 {
+        compatible = "xlnx,axi-perf-monitor";
+        interrupt-parent = <&axi_intc_1>;
+        interrupts = <1 2>;
+        reg = <0x44a00000 0x1000>;
+        clocks = <&clkc 15>;
+        xlnx,enable-profile = <0>;
+        xlnx,enable-trace = <0>;
+        xlnx,num-monitor-slots = <4>;
+        xlnx,enable-event-count = <1>;
+        xlnx,enable-event-log = <1>;
+        xlnx,have-sampled-metric-cnt = <1>;
+        xlnx,num-of-counters = <8>;
+        xlnx,metric-count-width = <32>;
+        xlnx,metrics-sample-count-width = <32>;
+        xlnx,global-count-width = <32>;
+        xlnx,metric-count-scale = <1>;
+        xlnx,id-filter-32bit;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/perf/xlnx-flexnoc-pm.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/perf/xlnx-flexnoc-pm.yaml
@@ -0,0 +1,46 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/perf/xlnx-flexnoc-pm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx flexnoc Performance Monitor device tree bindings
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+properties:
+  compatible:
+    # Versal SoC based boards
+    items:
+      - enum:
+          - xlnx,flexnoc-pm-2.7
+
+  reg:
+    items:
+      - description: funnel registers
+      - description: baselpd registers
+      - description: basefpd registers
+
+  reg-names:
+    # The core schema enforces this is a string array
+    items:
+      - const: funnel
+      - const: baselpd
+      - const: basefpd
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    performance-monitor@f0920000 {
+        compatible = "xlnx,flexnoc-pm-2.7";
+        reg-names = "funnel", "baselpd", "basefpd";
+        reg = <0x0 0xf0920000 0x0 0x1000>,
+              <0x0 0xf0980000 0x0 0x9000>,
+              <0x0 0xf0b80000 0x0 0x9000>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/phy/amlogic,g12a-usb2-phy.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/phy/amlogic,g12a-usb2-phy.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 BayLibre, SAS
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/amlogic,g12a-usb2-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Amlogic G12A USB2 PHY
+
+maintainers:
+  - Neil Armstrong <narmstrong@baylibre.com>
+
+properties:
+  compatible:
+    enum:
+      - amlogic,g12a-usb2-phy
+      - amlogic,a1-usb2-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: xtal
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    items:
+      - const: phy
+
+  "#phy-cells":
+    const: 0
+
+  phy-supply:
+    description:
+      Phandle to a regulator that provides power to the PHY. This
+      regulator will be managed during the PHY power on/off sequence.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - "#phy-cells"
+
+if:
+  properties:
+    compatible:
+      enum:
+        - amlogic,meson-a1-usb-ctrl
+
+then:
+  properties:
+    power-domains:
+      maxItems: 1
+  required:
+    - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    phy@36000 {
+          compatible = "amlogic,g12a-usb2-phy";
+          reg = <0x36000 0x2000>;
+          clocks = <&xtal>;
+          clock-names = "xtal";
+          resets = <&phy_reset>;
+          reset-names = "phy";
+          #phy-cells = <0>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/phy/amlogic,g12a-usb3-pcie-phy.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/phy/amlogic,g12a-usb3-pcie-phy.yaml
@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 BayLibre, SAS
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/amlogic,g12a-usb3-pcie-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Amlogic G12A USB3 + PCIE Combo PHY
+
+maintainers:
+  - Neil Armstrong <narmstrong@baylibre.com>
+
+properties:
+  compatible:
+    enum:
+      - amlogic,g12a-usb3-pcie-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: ref_clk
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    items:
+      - const: phy
+
+  "#phy-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    phy@46000 {
+          compatible = "amlogic,g12a-usb3-pcie-phy";
+          reg = <0x46000 0x2000>;
+          clocks = <&ref_clk>;
+          clock-names = "ref_clk";
+          resets = <&phy_reset>;
+          reset-names = "phy";
+          #phy-cells = <1>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
@@ -76,8 +76,7 @@
 
       connector:
         type: object
-        allOf:
-          - $ref: ../connector/usb-connector.yaml
+        $ref: /schemas/connector/usb-connector.yaml
         properties:
           vbus-supply: true
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/phy/xlnx,gt-quad-base.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/phy/xlnx,gt-quad-base.yaml
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/xlnx,gt-quad-base.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx DP GTQUAD PHY
+
+maintainers:
+  - Jagadeesh Banisetti <jagadeesh.banisetti@xilinx.com>
+
+description: |
+  The Xilinx DP GTQUAD PHY Controller core is designed for enabling
+  connectivity with Xilinx DP RX and TX with xilinx versal devices.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,gt-quad-base-1.1
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: List of clock specifiers
+    items:
+      - description: AXI Lite clock
+
+  "#phy-cells":
+    const: 0
+
+required:
+  - clocks
+  - compatible
+  - reg
+  - '#phy-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+   gt_quad_base: gt_qb@a4080000 {
+           clocks = <&misc_clk_0>;
+           compatible = "xlnx,gt-quad-base-1.1";
+           reg = <0xa4080000 0x10000>;
+           #phy-cells = <0>;
+   };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/phy/xlnx,v-hmdi-phy1.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/phy/xlnx,v-hmdi-phy1.yaml
@@ -0,0 +1,228 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/xlnx,v-hmdi-phy1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx HDMI PHY
+
+maintainers:
+  - Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>
+
+description: |
+  The Xilinx HDMI PHY Controller core is designed for enabling plug-and-play
+  connectivity with Xilinx HDMI 2.1 technology MAC transmit or receive
+  subsystems. The interface between the video MAC and PHY layers are
+  standardized to enable ease of use in accessing shared transceiver resource.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,v-hdmi-phy1-1.0
+
+  reg:
+    maxItems: 1
+
+  rxch4-sel-gpios:
+    maxItems: 1
+    description: |
+      Select HDMI 2.1 PHY Rx channel as data or clock based on FRL or TMDS mode.
+      Polarity of this GPIO is GPIO_ACTIVE_LOW
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: List of clock specifiers
+    items:
+      - description: AXI Lite clock
+      - description: DRP clock
+
+  clock-names:
+    items:
+      - const: axi4lite_aclk
+      - const: drpclk
+
+  xlnx,transceiver-type:
+    description: |
+      Gigabit transceiver type that IP configured with.Possible values are as
+      below -
+      5  - GTHE4
+      6  - GTYE4
+      7  - GTYE5
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [5, 6, 7]
+
+  xlnx,tx-no-of-channels:
+    description: Max number of channels that Tx configured with.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4]
+
+  xlnx,rx-no-of-channels:
+    description: Max number of channels that Rx configured with.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4]
+
+  xlnx,rx-protocol:
+    description: Protocol type that Tx is configured with.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 3
+
+  xlnx,tx-protocol:
+    description: Protocol type that Rx is configured with.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 3
+
+  xlnx,nidru:
+    description: nidru present in the IP or not.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1]
+
+  xlnx,tx-refclk-sel:
+    description: Available reference clocks for Tx PLL clock selection
+                 multiplexer.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 6
+
+  xlnx,rx-refclk-sel:
+    description: Available reference clocks for Rx PLL clock selection
+                 multiplexer.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 6
+
+  xlnx,tx-frl-refclk-sel:
+    description: Available reference clocks for Tx PLL FRL(fixed rate link)
+                 clock selection multiplexer.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 7
+
+  xlnx,rx-frl-refclk-sel:
+    description: Available reference clocks for Rx PLL FRL(fixed rate link)
+                 clock selection multiplexer.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 6
+
+  xlnx,tx-pll-selection:
+    description: Available reference clocks used to driver Tx datapath.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 6
+
+  xlnx,rx-pll-selection:
+    description: Available reference clocks used to driver Rx datapath.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 6
+
+  xlnx,nidru-refclk-sel:
+    description: Available reference clocks for NI-DRU(non-integer data rate
+                 unit) clock selection multiplexer.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 7
+
+  xlnx,transceiver-width:
+    description: Transceiver width that IP is configured with.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [2, 4]
+
+  xlnx,input-pixels-per-clock:
+    description: |
+      Input number of pixel per clock that IP configured with.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4, 8]
+
+  xlnx,use-gt-ch4-hdmi:
+    description: |
+      use 4th GT channel as tx TMDS clock.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [0, 1]
+
+  xlnx,rx-max-gt-line-rate:
+    description: |
+      Maxmimum Rx GT linerate that IP is configured with.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [3, 6, 8, 10, 12]
+
+  xlnx,tx-max-gt-line-rate:
+    description: |
+      Maxmimum Tx GT linerate that IP is configured with.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [3, 6, 8, 10, 12]
+
+  "#phy-cells":
+    const: 0
+
+required:
+  - clock-names
+  - clocks
+  - compatible
+  - interrupts
+  - reg
+  - rxch4-sel-gpios
+  - xlnx,transceiver-type
+  - xlnx,tx-no-of-channels
+  - xlnx,rx-no-of-channels
+  - xlnx,tx-refclk-sel
+  - xlnx,rx-refclk-sel
+  - xlnx,tx-frl-refclk-sel
+  - xlnx,rx-frl-refclk-sel
+  - xlnx,tx-pll-selection
+  - xlnx,rx-pll-selection
+  - xlnx,nidru-refclk-sel
+  - xlnx,transceiver-width
+  - xlnx,input-pixels-per-clock
+  - xlnx,use-gt-ch4-hdmi
+  - xlnx,rx-max-gt-line-rate
+  - xlnx,tx-max-gt-line-rate
+  - '#phy-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+   v_hdmi_phy1@80040000 {
+           clock-names = "axi4lite_aclk", "drpclk";
+           clocks =  <&zynqmp_clk 71>, <&zynqmp_clk 71>;
+           compatible = "xlnx,v-hdmi-phy1-1.0";
+           interrupt-parent = <&gic>;
+           interrupts = <0 89 4>;
+           reg = <0x80040000 0x10000>;
+           rxch4-sel-gpios = <&foo_gpio 18 1>;
+           xlnx,transceiver-type = <5>;
+           xlnx,tx-no-of-channels = <4>;
+           xlnx,rx-no-of-channels = <4>;
+           xlnx,rx-protocol = <2>;
+           xlnx,tx-protocol = <2>;
+           xlnx,tx-refclk-sel = <2>;
+           xlnx,rx-refclk-sel = <0>;
+           xlnx,tx-frl-refclk-sel = <2>;
+           xlnx,rx-frl-refclk-sel = <0>;
+           xlnx,tx-pll-selection = <6>;
+           xlnx,rx-pll-selection = <0>;
+           xlnx,nidru = <1>;
+           xlnx,nidru-refclk-sel = <4>;
+           xlnx,transceiver-width = <4>;
+           xlnx,input-pixels-per-clock = <4>;
+           xlnx,use-gt-ch4-hdmi = <1>;
+           xlnx,rx-max-gt-line-rate = <0xc>;
+           xlnx,tx-max-gt-line-rate = <0xc>;
+           #phy-cells = <0>;
+   };
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml
@@ -58,7 +58,7 @@
           $ref: "/schemas/types.yaml#/definitions/string"
           enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2,
                   ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMCG1, EMMCG4,
-                  EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWQSPID, FWSPIWP,
+                  EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWSPIWP,
                   GPIT0, GPIT1, GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1,
                   GPIU2, GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, HVI3C3, HVI3C4, I2C1, I2C10,
                   I2C11, I2C12, I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, I2C4, I2C5,
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml
@@ -94,7 +94,8 @@
             then:
               properties:
                 groups:
-                  enum: [emmc, emmc_rst]
+                  items:
+                    enum: [emmc, emmc_rst]
           - if:
               properties:
                 function:
@@ -102,8 +103,9 @@
             then:
               properties:
                 groups:
-                  enum: [esw, esw_p0_p1, esw_p2_p3_p4, rgmii_via_esw,
-                         rgmii_via_gmac1, rgmii_via_gmac2, mdc_mdio]
+                  items:
+                    enum: [esw, esw_p0_p1, esw_p2_p3_p4, rgmii_via_esw,
+                           rgmii_via_gmac1, rgmii_via_gmac2, mdc_mdio]
           - if:
               properties:
                 function:
@@ -120,10 +122,11 @@
             then:
               properties:
                 groups:
-                  enum: [i2s_in_mclk_bclk_ws, i2s1_in_data, i2s2_in_data,
-                         i2s3_in_data, i2s4_in_data, i2s_out_mclk_bclk_ws,
-                         i2s1_out_data, i2s2_out_data, i2s3_out_data,
-                         i2s4_out_data]
+                  items:
+                    enum: [i2s_in_mclk_bclk_ws, i2s1_in_data, i2s2_in_data,
+                           i2s3_in_data, i2s4_in_data, i2s_out_mclk_bclk_ws,
+                           i2s1_out_data, i2s2_out_data, i2s3_out_data,
+                           i2s4_out_data]
           - if:
               properties:
                 function:
@@ -156,10 +159,11 @@
             then:
               properties:
                 groups:
-                  enum: [pcie0_0_waken, pcie0_1_waken, pcie1_0_waken,
-                         pcie0_0_clkreq, pcie0_1_clkreq, pcie1_0_clkreq,
-                         pcie0_pad_perst, pcie1_pad_perst, pcie_pereset,
-                         pcie_wake, pcie_clkreq]
+                  items:
+                    enum: [pcie0_0_waken, pcie0_1_waken, pcie1_0_waken,
+                           pcie0_0_clkreq, pcie0_1_clkreq, pcie1_0_clkreq,
+                           pcie0_pad_perst, pcie1_pad_perst, pcie_pereset,
+                           pcie_wake, pcie_clkreq]
           - if:
               properties:
                 function:
@@ -175,11 +179,12 @@
             then:
               properties:
                 groups:
-                  enum: [pwm_ch1_0, pwm_ch1_1, pwm_ch1_2, pwm_ch2_0, pwm_ch2_1,
-                         pwm_ch2_2, pwm_ch3_0, pwm_ch3_1, pwm_ch3_2, pwm_ch4_0,
-                         pwm_ch4_1, pwm_ch4_2, pwm_ch4_3, pwm_ch5_0, pwm_ch5_1,
-                         pwm_ch5_2, pwm_ch6_0, pwm_ch6_1, pwm_ch6_2, pwm_ch6_3,
-                         pwm_ch7_0, pwm_0, pwm_1]
+                  items:
+                    enum: [pwm_ch1_0, pwm_ch1_1, pwm_ch1_2, pwm_ch2_0, pwm_ch2_1,
+                           pwm_ch2_2, pwm_ch3_0, pwm_ch3_1, pwm_ch3_2, pwm_ch4_0,
+                           pwm_ch4_1, pwm_ch4_2, pwm_ch4_3, pwm_ch5_0, pwm_ch5_1,
+                           pwm_ch5_2, pwm_ch6_0, pwm_ch6_1, pwm_ch6_2, pwm_ch6_3,
+                           pwm_ch7_0, pwm_0, pwm_1]
           - if:
               properties:
                 function:
@@ -257,33 +262,34 @@
           pins:
             description: |
               An array of strings. Each string contains the name of a pin.
-            enum: [GPIO_A, I2S1_IN, I2S1_OUT, I2S_BCLK, I2S_WS, I2S_MCLK, TXD0,
-                   RXD0, SPI_WP, SPI_HOLD, SPI_CLK, SPI_MOSI, SPI_MISO, SPI_CS,
-                   I2C_SDA, I2C_SCL, I2S2_IN, I2S3_IN, I2S4_IN, I2S2_OUT,
-                   I2S3_OUT, I2S4_OUT, GPIO_B, MDC, MDIO, G2_TXD0, G2_TXD1,
-                   G2_TXD2, G2_TXD3, G2_TXEN, G2_TXC, G2_RXD0, G2_RXD1, G2_RXD2,
-                   G2_RXD3, G2_RXDV, G2_RXC, NCEB, NWEB, NREB, NDL4, NDL5, NDL6,
-                   NDL7, NRB, NCLE, NALE, NDL0, NDL1, NDL2, NDL3, MDI_TP_P0,
-                   MDI_TN_P0, MDI_RP_P0, MDI_RN_P0, MDI_TP_P1, MDI_TN_P1,
-                   MDI_RP_P1, MDI_RN_P1, MDI_RP_P2, MDI_RN_P2, MDI_TP_P2,
-                   MDI_TN_P2, MDI_TP_P3, MDI_TN_P3, MDI_RP_P3, MDI_RN_P3,
-                   MDI_RP_P4, MDI_RN_P4, MDI_TP_P4, MDI_TN_P4, PMIC_SCL,
-                   PMIC_SDA, SPIC1_CLK, SPIC1_MOSI, SPIC1_MISO, SPIC1_CS,
-                   GPIO_D, WATCHDOG, RTS3_N, CTS3_N, TXD3, RXD3, PERST0_N,
-                   PERST1_N, WLED_N, EPHY_LED0_N, AUXIN0, AUXIN1, AUXIN2,
-                   AUXIN3, TXD4, RXD4, RTS4_N, CST4_N, PWM1, PWM2, PWM3, PWM4,
-                   PWM5, PWM6, PWM7, GPIO_E, TOP_5G_CLK, TOP_5G_DATA,
-                   WF0_5G_HB0, WF0_5G_HB1, WF0_5G_HB2, WF0_5G_HB3, WF0_5G_HB4,
-                   WF0_5G_HB5, WF0_5G_HB6, XO_REQ, TOP_RST_N, SYS_WATCHDOG,
-                   EPHY_LED0_N_JTDO, EPHY_LED1_N_JTDI, EPHY_LED2_N_JTMS,
-                   EPHY_LED3_N_JTCLK, EPHY_LED4_N_JTRST_N, WF2G_LED_N,
-                   WF5G_LED_N, GPIO_9, GPIO_10, GPIO_11, GPIO_12, UART1_TXD,
-                   UART1_RXD, UART1_CTS, UART1_RTS, UART2_TXD, UART2_RXD,
-                   UART2_CTS, UART2_RTS, SMI_MDC, SMI_MDIO, PCIE_PERESET_N,
-                   PWM_0, GPIO_0, GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5,
-                   GPIO_6, GPIO_7, GPIO_8, UART0_TXD, UART0_RXD, TOP_2G_CLK,
-                   TOP_2G_DATA, WF0_2G_HB0, WF0_2G_HB1, WF0_2G_HB2, WF0_2G_HB3,
-                   WF0_2G_HB4, WF0_2G_HB5, WF0_2G_HB6]
+            items:
+              enum: [GPIO_A, I2S1_IN, I2S1_OUT, I2S_BCLK, I2S_WS, I2S_MCLK, TXD0,
+                     RXD0, SPI_WP, SPI_HOLD, SPI_CLK, SPI_MOSI, SPI_MISO, SPI_CS,
+                     I2C_SDA, I2C_SCL, I2S2_IN, I2S3_IN, I2S4_IN, I2S2_OUT,
+                     I2S3_OUT, I2S4_OUT, GPIO_B, MDC, MDIO, G2_TXD0, G2_TXD1,
+                     G2_TXD2, G2_TXD3, G2_TXEN, G2_TXC, G2_RXD0, G2_RXD1, G2_RXD2,
+                     G2_RXD3, G2_RXDV, G2_RXC, NCEB, NWEB, NREB, NDL4, NDL5, NDL6,
+                     NDL7, NRB, NCLE, NALE, NDL0, NDL1, NDL2, NDL3, MDI_TP_P0,
+                     MDI_TN_P0, MDI_RP_P0, MDI_RN_P0, MDI_TP_P1, MDI_TN_P1,
+                     MDI_RP_P1, MDI_RN_P1, MDI_RP_P2, MDI_RN_P2, MDI_TP_P2,
+                     MDI_TN_P2, MDI_TP_P3, MDI_TN_P3, MDI_RP_P3, MDI_RN_P3,
+                     MDI_RP_P4, MDI_RN_P4, MDI_TP_P4, MDI_TN_P4, PMIC_SCL,
+                     PMIC_SDA, SPIC1_CLK, SPIC1_MOSI, SPIC1_MISO, SPIC1_CS,
+                     GPIO_D, WATCHDOG, RTS3_N, CTS3_N, TXD3, RXD3, PERST0_N,
+                     PERST1_N, WLED_N, EPHY_LED0_N, AUXIN0, AUXIN1, AUXIN2,
+                     AUXIN3, TXD4, RXD4, RTS4_N, CST4_N, PWM1, PWM2, PWM3, PWM4,
+                     PWM5, PWM6, PWM7, GPIO_E, TOP_5G_CLK, TOP_5G_DATA,
+                     WF0_5G_HB0, WF0_5G_HB1, WF0_5G_HB2, WF0_5G_HB3, WF0_5G_HB4,
+                     WF0_5G_HB5, WF0_5G_HB6, XO_REQ, TOP_RST_N, SYS_WATCHDOG,
+                     EPHY_LED0_N_JTDO, EPHY_LED1_N_JTDI, EPHY_LED2_N_JTMS,
+                     EPHY_LED3_N_JTCLK, EPHY_LED4_N_JTRST_N, WF2G_LED_N,
+                     WF5G_LED_N, GPIO_9, GPIO_10, GPIO_11, GPIO_12, UART1_TXD,
+                     UART1_RXD, UART1_CTS, UART1_RTS, UART2_TXD, UART2_RXD,
+                     UART2_CTS, UART2_RTS, SMI_MDC, SMI_MDIO, PCIE_PERESET_N,
+                     PWM_0, GPIO_0, GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5,
+                     GPIO_6, GPIO_7, GPIO_8, UART0_TXD, UART0_RXD, TOP_2G_CLK,
+                     TOP_2G_DATA, WF0_2G_HB0, WF0_2G_HB1, WF0_2G_HB2, WF0_2G_HB3,
+                     WF0_2G_HB4, WF0_2G_HB5, WF0_2G_HB6]
 
           bias-disable: true
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
@@ -138,7 +138,7 @@
       clocks = <&sys_clk>;
       pinctrl-0 = <&sgpio2_pins>;
       pinctrl-names = "default";
-      reg = <0x1101059c 0x100>;
+      reg = <0x1101059c 0x118>;
       microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
       bus-frequency = <25000000>;
       sgpio_in2: gpio@0 {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.yaml
@@ -46,9 +46,7 @@
 patternProperties:
   "^i2c@[1-4]$":
     type: object
-
-    allOf:
-      - $ref: /schemas/i2c/i2c-controller.yaml#
+    $ref: /schemas/i2c/i2c-controller.yaml#
 
 examples:
   - |
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/ptp/ptp-xilinx.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/ptp/ptp-xilinx.yaml
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ptp/ptp-xilinx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx 1588 PTP timer-syncer
+
+maintainers:
+  - Harini Katakam <harini.katakam@xilinx.com>
+
+description: |
+  Xilinx 1588 PTP timer-syncer IP provides  precision timing functionality
+  along with capabiity for time and fine adjustment. This IP is provided
+  for use with Xilinx Ethernet MAC with HW timestamping capability.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,timer-syncer-1588-1.0 #Deprecated
+      - xlnx,timer-syncer-1588-2.0
+
+  reg:
+    description: |
+      Offset and length of the register set for the device.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    ptp_timer@80000000 {
+        compatible = "xlnx,timer-syncer-1588-2.0";
+        reg = <0x80000000 0x10000>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/regulator/mt6315-regulator.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/regulator/mt6315-regulator.yaml
@@ -30,10 +30,6 @@
         type: object
         $ref: "regulator.yaml#"
 
-        properties:
-          regulator-name:
-            pattern: "^vbuck[1-4]$"
-
     additionalProperties: false
 
 required:
@@ -51,19 +47,17 @@
 
       regulators {
         vbuck1 {
-          regulator-compatible = "vbuck1";
           regulator-min-microvolt = <300000>;
           regulator-max-microvolt = <1193750>;
           regulator-enable-ramp-delay = <256>;
-          regulator-allowed-modes = <0 1 2 4>;
+          regulator-allowed-modes = <0 1 2>;
         };
 
         vbuck3 {
-          regulator-compatible = "vbuck3";
           regulator-min-microvolt = <300000>;
           regulator-max-microvolt = <1193750>;
           regulator-enable-ramp-delay = <256>;
-          regulator-allowed-modes = <0 1 2 4>;
+          regulator-allowed-modes = <0 1 2>;
         };
       };
     };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
@@ -47,12 +47,6 @@
         description:
           Properties for single LDO regulator.
 
-        properties:
-          regulator-name:
-            pattern: "^LDO[1-5]$"
-            description:
-              should be "LDO1", ..., "LDO5"
-
         unevaluatedProperties: false
 
       "^BUCK[1-6]$":
@@ -62,11 +56,6 @@
           Properties for single BUCK regulator.
 
         properties:
-          regulator-name:
-            pattern: "^BUCK[1-6]$"
-            description:
-              should be "BUCK1", ..., "BUCK6"
-
           nxp,dvs-run-voltage:
             $ref: "/schemas/types.yaml#/definitions/uint32"
             minimum: 600000
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt
@@ -13,6 +13,14 @@
 
 
 Required properties of the main device node (the parent!):
+ - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
+   for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
+
+ [1] If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
+     property is specified, then all the eight voltage values for the
+     's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
+
+Optional properties of the main device node (the parent!):
  - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
    units for buck2 when changing voltage using gpio dvs. Refer to [1] below
    for additional information.
@@ -25,26 +33,13 @@
    units for buck4 when changing voltage using gpio dvs. Refer to [1] below
    for additional information.
 
- - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
-   for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
-
- [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
-     property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
-     property should specify atleast one voltage level (which would be a
-     safe operating voltage).
-
-     If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
-     property is specified, then all the eight voltage values for the
-     's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
-
-Optional properties of the main device node (the parent!):
  - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
  - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
  - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
 
 Additional properties required if either of the optional properties are used:
 
- - s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
+ - s5m8767,pmic-buck-default-dvs-idx: Default voltage setting selected from
    the possible 8 options selectable by the dvs gpios. The value of this
    property should be between 0 and 7. If not specified or if out of range, the
    default value of this property is set to 0.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml
@@ -94,8 +94,7 @@
       addresses. Cache and memory access settings are provided through a
       Memory Protection Unit (MPU), programmable only from the R5Fs.
 
-    allOf:
-      - $ref: /schemas/arm/keystone/ti,k3-sci-common.yaml#
+    $ref: /schemas/arm/keystone/ti,k3-sci-common.yaml#
 
     properties:
       compatible:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml
@@ -0,0 +1,224 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Xilinx R5 remote processor controller bindings
+
+description:
+  This document defines the binding for the remoteproc component that loads and
+  boots firmwares on the Xilinx Zynqmp and Versal family chipsets.
+
+  Note that the Linux has global addressing view of the R5-related memory (TCM)
+  so the absolute address ranges are provided in TCM reg's.
+
+maintainers:
+  - Ed Mooring <ed.mooring@xilinx.com>
+  - Ben Levinsky <ben.levinsky@xilinx.com>
+
+properties:
+  $nodename:
+    pattern: "^r5fss(@.*)?"
+
+  compatible:
+    enum:
+      - xlnx,zynqmp-r5-remoteproc
+      - xlnx,versal-r5-remoteproc
+
+  reg:
+    items:
+      - description: Address and Size of Xilinx RPU Configuration register
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 2
+
+  ranges: true
+
+# Optional properties:
+# --------------------
+  xlnx,cluster-mode:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+    description: |
+      Configuration Mode for the Dual R5F cores within the R5F cluster.
+      Should be either a value of 0 (LockStep mode) or 1 (Split mode),
+      default is LockStep mode if omitted.
+
+
+#R5F Processor Child Nodes:
+# ==========================
+
+patternProperties:
+  "^r5f_[a-f0-9]+$":
+    type: object
+    description: |
+      The R5F Sub-System device node should define one or two R5F child nodes,
+      each node representing a Xilinx instantiation of the Arm Cortex R5F core.
+      There should be one or two child nodes if the R5F is in Split mode and
+      one child node if the R5F is in Lockstep mode.
+
+      In Split mode each R5F core has two associated TCM Banks. R5_0 has
+      TCM Banks 0A and 0B and R5_1 has TCM Banks 1A and 1B.
+
+      In Lockstep mode only one R5F child node should be defined. This one
+      child has access to TCM Banks 0A, 0B, 1A and 1B and any of the four can
+      be included in the child R5F's sram property.
+
+      The example below shows Split mode with two child nodes.
+
+    properties:
+      compatible:
+        enum:
+          - xilinx,r5f
+
+# The following properties are mandatory for R5F Core0 in both LockStep and Split
+# modes, and are mandatory for R5F Core1 _only_ in Split mode.
+
+      memory-region:
+        description: |
+          Phandles to the memory nodes to be associated with the
+          The reserved memory nodes should be carveout nodes, and
+          should be defined with a "no-map" property as per the bindings in
+          Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
+        minItems: 1
+        maxItems: 6
+        items:
+          - description: Region used for dynamic DMA allocations like vrings and
+                         vring buffers
+          - description: region reserved for firmware image sections
+        additionalItems: true
+
+      power-domain:
+        description: |
+          Power node ID that is used to uniquely identify the RPU for Xilinx
+          Power Management.
+        maxItems: 1
+
+# Optional properties:
+# --------------------
+# The following properties are optional properties for each of the R5F cores:
+
+      mboxes:
+        description: |
+          Standard property to specify a mailbox
+          This property is required only if the rpmsg/virtio functionality
+          is used
+
+           Refer to the zynqmp-ipi-mailbox documentation for client usage of this
+           property
+        maxItems: 1
+
+      mbox-names:
+        description: |
+          Refer to the zynqmp-ipi-mailbox documentation for client usage of this
+          property
+        items:
+          - const: tx
+          - const: rx
+
+      sram:
+        $ref: /schemas/types.yaml#/definitions/phandle-array
+        minItems: 1
+        maxItems: 4
+        description: |
+          Phandles to one or more reserved on-chip SRAM regions. The regions
+          should be defined as child nodes of the respective SRAM node, and
+          should be defined as per the generic bindings in,
+          Documentation/devicetree/bindings/sram/sram.yaml
+
+    required:
+      - compatible
+      - power-domain
+
+    unevaluatedProperties: false
+
+required:
+  - reg
+  - compatible
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    / {
+        compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+        #address-cells = <2>;
+        #size-cells = <2>;
+        model = "ZynqMP ZCU102 ";
+
+        zynqmp_ipi1 {
+          compatible = "xlnx,zynqmp-ipi-mailbox";
+          interrupt-parent = <&gic>;
+          interrupts = <0 33 4>;
+          xlnx,ipi-id = <5>;
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          ipi_mailbox_rpu0: mailbox@ff990600 {
+            reg = <0xff990600 0x20>,
+                  <0xff990620 0x20>,
+                  <0xff9900c0 0x20>,
+                  <0xff9900e0 0x20>;
+            reg-names = "local_request_region",
+            "local_response_region",
+            "remote_request_region",
+            "remote_response_region";
+            #mbox-cells = <1>;
+            xlnx,ipi-id = <3>;
+          };
+          ipi_mailbox_rpu1: mailbox@ff990780 {
+            reg = <0xff990780 0x20>,
+                  <0xff9907a0 0x20>,
+                  <0xff9907c0 0x20>,
+                  <0xff9905a0 0x20>;
+            reg-names = "local_request_region",
+            "local_response_region",
+            "remote_request_region",
+            "remote_response_region";
+            #mbox-cells = <1>;
+            xlnx,ipi-id = <3>;
+          };
+        };
+
+        r5fss@ff9a0000 {
+          compatible = "xlnx,zynqmp-r5-remoteproc";
+          #address-cells = <2>;
+          #size-cells = <2>;
+          ranges;
+          reg = <0x0 0xff9a0000 0x0 0x10000>;
+          xlnx,cluster-mode = <0>;
+
+          r5f_0 {
+               compatible = "xilinx,r5f";
+               memory-region = <&elf_load0>,
+                               <&rpu0vdev0vring0>,
+                               <&rpu0vdev0vring1>,
+                               <&rpu0vdev0buffer>;
+               sram = <&tcm_0a>, <&tcm_0b>;
+               mboxes = <&ipi_mailbox_rpu0 0x0 &ipi_mailbox_rpu0 0x1>;
+               mbox-names = "tx", "rx";
+               power-domain = <0x7>;
+          };
+          r5f_1 {
+               compatible = "xilinx,r5f";
+               memory-region = <&elf_load1>,
+                               <&rpu1vdev0vring0>,
+                               <&rpu1vdev0vring1>,
+                               <&rpu1vdev0buffer>;
+               sram = <&tcm_1a>, <&tcm_1b>;
+               mboxes = <&ipi_mailbox_rpu1 0x0 &ipi_mailbox_rpu1 0x1>;
+               mbox-names = "tx", "rx";
+               power-domain = <0x8>;
+          };
+
+        };
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/remoteproc/zynq_remoteproc.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/remoteproc/zynq_remoteproc.txt
@@ -0,0 +1,47 @@
+Xilinx ARM Cortex A9-A9 remoteproc driver
+==========================================
+
+Zynq family of devices can use one A9 processor to help with various
+low power / real time tasks.
+
+This driver requires specific Zynq hardware design.
+
+Zynq RemoteProc Device Node:
+=================================
+A zynq_remoteproc device node is used to represent the 2nd A9 instance
+within Zynq SoC.
+
+Required properties:
+--------------------
+ - compatible : should be "xlnx,zynq_remoteproc"
+ - vring0: soft interrupt for kicking from firmware
+ - vring1: soft interrupt for kicking from Linux kernel
+
+Optional Properties:
+--------------------
+ - memory-region: reserved memory which will be used by R5 processor
+
+Example:
+--------
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rproc_0_reserved: rproc@3e000000 {
+			no-map;
+			reg = <0x3e000000 0x400000>;
+		};
+		rproc_0_dma: rproc@3e800000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0x3e800000 0x100000>;
+		};
+	};
+
+	zynq_remoteproc@0 {
+		compatible = "xlnx,zynq_remoteproc";
+		vring0 = <15>;
+		vring1 = <14>;
+		memory-region = <&rproc_0_reserved>, <&rproc_0_dma>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/riscv/sifive-l2-cache.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/riscv/sifive-l2-cache.yaml
@@ -47,7 +47,7 @@
     const: 2
 
   cache-sets:
-    const: 1024
+    enum: [1024, 2048]
 
   cache-size:
     const: 2097152
@@ -85,6 +85,8 @@
       description: |
         Must contain entries for DirError, DataError and DataFail signals.
       maxItems: 3
+    cache-sets:
+      const: 1024
 
 else:
   properties:
@@ -92,6 +94,8 @@
       description: |
         Must contain entries for DirError, DataError, DataFail, DirFail signals.
       minItems: 4
+    cache-sets:
+      const: 2048
 
 additionalProperties: false
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/serial/cdns,uart.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/serial/cdns,uart.yaml
@@ -9,9 +9,6 @@
 maintainers:
   - Michal Simek <michal.simek@xilinx.com>
 
-allOf:
-  - $ref: /schemas/serial.yaml#
-
 properties:
   compatible:
     oneOf:
@@ -46,6 +43,12 @@
       port does not use this pin.
     type: boolean
 
+  power-domains:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
 required:
   - compatible
   - reg
@@ -53,6 +56,18 @@
   - clocks
   - clock-names
 
+allOf:
+  - $ref: serial.yaml#
+  - $ref: rs485.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: cdns,uart-r1p8
+    then:
+      properties:
+        power-domains: false
+
 unevaluatedProperties: false
 
 examples:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/serial/pl011.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/serial/pl011.yaml
@@ -19,14 +19,19 @@
       contains:
         enum:
           - arm,pl011
+          - arm,xlnx-sbsa-uart
   required:
     - compatible
 
 properties:
   compatible:
-    items:
-      - const: arm,pl011
-      - const: arm,primecell
+    oneOf:
+      - items:
+          - const: arm,pl011
+          - const: arm,primecell
+      - items:
+          - const: arm,xlnx-sbsa-uart
+          - const: arm,primecell
 
   reg:
     maxItems: 1
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/serial/renesas,scif.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/serial/renesas,scif.yaml
@@ -79,7 +79,7 @@
           - description: Error interrupt
           - description: Receive buffer full interrupt
           - description: Transmit buffer empty interrupt
-          - description: Transmit End interrupt
+          - description: Break interrupt
       - items:
           - description: Error interrupt
           - description: Receive buffer full interrupt
@@ -94,7 +94,7 @@
           - const: eri
           - const: rxi
           - const: txi
-          - const: tei
+          - const: bri
       - items:
           - const: eri
           - const: rxi
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/serial/rs485.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/serial/rs485.yaml
@@ -18,16 +18,15 @@
     description: prop-encoded-array <a b>
     $ref: /schemas/types.yaml#/definitions/uint32-array
     items:
-      items:
-        - description: Delay between rts signal and beginning of data sent in
-            milliseconds. It corresponds to the delay before sending data.
-          default: 0
-          maximum: 1000
-        - description: Delay between end of data sent and rts signal in milliseconds.
-            It corresponds to the delay after sending data and actual release
-            of the line.
-          default: 0
-          maximum: 1000
+      - description: Delay between rts signal and beginning of data sent in
+          milliseconds. It corresponds to the delay before sending data.
+        default: 0
+        maximum: 100
+      - description: Delay between end of data sent and rts signal in milliseconds.
+          It corresponds to the delay after sending data and actual release
+          of the line.
+        default: 0
+        maximum: 100
 
   rs485-rts-active-low:
     description: drive RTS low when sending (default is high).
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/xlnx,opb-uartlite.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+maintainers:
+  - Michal Simek <michals@xilinx.com>
+
+title: Xilinx uartlite bindings
+
+properties:
+  compatible:
+    enum:
+      - xlnx,opb-uartlite-1.00.b
+      - xlnx,xps-uartlite-1.00.a
+      - xlnx,axi-uartlite-rs485
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-name:
+    const: s_axi_aclk
+    description: |
+      Input clock name.
+
+  port-number:
+    $ref: '/schemas/types.yaml#/definitions/uint32'
+    description:
+      The port number of the uartlite.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    serial@800c0000 {
+      compatible = "xlnx,xps-uartlite-1.00.a";
+      reg = <0x800c0000 0x10000>;
+      interrupts = <0x0 0x6e 0x1>;
+      port-number = <0>;
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
@@ -34,6 +34,8 @@
       - qcom,rpm-ipq6018
       - qcom,rpm-msm8226
       - qcom,rpm-msm8916
+      - qcom,rpm-msm8936
+      - qcom,rpm-msm8953
       - qcom,rpm-msm8974
       - qcom,rpm-msm8976
       - qcom,rpm-msm8996
@@ -57,6 +59,7 @@
           - qcom,rpm-apq8084
           - qcom,rpm-msm8916
           - qcom,rpm-msm8974
+          - qcom,rpm-msm8953
 then:
   required:
     - qcom,smd-channels
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -141,6 +141,7 @@
           unevaluatedProperties: false
 
         pcie-phy:
+          type: object
           description:
             Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
@@ -281,10 +281,7 @@
       PRUSS INTC Node. Each PRUSS has a single interrupt controller instance
       that is common to all the PRU cores. This should be represented as an
       interrupt-controller node.
-
-    allOf:
-      - $ref: /schemas/interrupt-controller/ti,pruss-intc.yaml#
-
+    $ref: /schemas/interrupt-controller/ti,pruss-intc.yaml#
     type: object
 
   mdio@[a-f0-9]+$:
@@ -292,10 +289,7 @@
       MDIO Node. Each PRUSS has an MDIO module that can be used to control
       external PHYs. The MDIO module used within the PRU-ICSS is an instance of
       the MDIO Controller used in TI Davinci SoCs.
-
-    allOf:
-      - $ref: /schemas/net/ti,davinci-mdio.yaml#
-
+    $ref: /schemas/net/ti,davinci-mdio.yaml#
     type: object
 
   "^(pru|rtu|txpru)@[0-9a-f]+$":
@@ -305,10 +299,7 @@
       inactive by using the standard DT string property, "status". The ICSSG IP
       present on K3 SoCs have additional auxiliary PRU cores with slightly
       different IP integration.
-
-    allOf:
-      - $ref: /schemas/remoteproc/ti,pru-rproc.yaml#
-
+    $ref: /schemas/remoteproc/ti,pru-rproc.yaml#
     type: object
 
 required:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/soc/xilinx/xlnx,ai-engine-npi.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/soc/xilinx/xlnx,ai-engine-npi.txt
@@ -0,0 +1,23 @@
+Xilinx AI Engine NPI
+--------------------
+
+The Xilinx AI Engine NPI space is where the privileged operations for AI Engine
+device are handled, such as reset and pll. The space is typically meant to be
+owned by platform management software, and this space is accessible only when
+the platform management software grants the access. Thus, this dt binding only
+works in such configuration, and in case the platform locks the access,
+the non-secure software fails to access the device.
+
+This is a temporary solution to allow direct access to NPI space.
+
+Required properties:
+
+- compatible: Must be "xlnx,ai-engine-npi"
+- reg: Physical base address and length of the registers set for the device.
+
+Example:
+
+	aie-npi@f70a0000 {
+		compatible = "xlnx,ai-engine-npi";
+		reg = <0x0 0xf70a0000 0x0 0x1000>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/soc/xilinx/xlnx,ai-engine.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/soc/xilinx/xlnx,ai-engine.yaml
@@ -0,0 +1,199 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/xilinx/xlnx,ai-engine.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx AI Engine
+
+maintainers:
+  - Wendy Liang <wendy.liang@xilinx.com>
+
+description: |+
+  The Xilinx AI Engine is a tile processor with many cores (up to 400) that
+  can run in parallel. The data routing between cores is configured through
+  internal switches, and shim tiles interface with external interconnect, such
+  as memory or PL. One AI engine device can have multiple apertures, each
+  has its own address space and interrupt. At runtime application can create
+  multiple partitions within an aperture which are groups of columns of AI
+  engine tiles. Each AI engine partition is the minimum resetable unit for an
+  AI engine application.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,ai-engine-v2.0
+      - xlnx,ai-engine-v1.0 # deprecated
+
+  reg:
+    deprecated: true
+    description: |
+      Physical base address and length of the device registers.
+      The AI engine address space assigned to Linux is defined by Xilinx
+      platform design tool.
+
+  '#address-cells':
+    enum: [2]
+    description: |
+      size of cell to describe AI engine range of tiles address.
+      It is the location of the starting tile of the range.
+      As the AI engine tiles are 2D array, the location of a tile
+      is presented as (column, row), the address cell is 2.
+
+  '#size-cells':
+    enum: [2]
+    description: |
+      size of cell to describe AI engine range of tiles size.
+      As the AI engine tiles are 2D array, the size cell is 2.
+
+  interrupts:
+    deprecated: true
+    maxItems: 3
+
+  interrupt-names:
+    deprecated: true
+    description: |
+      Should be "interrupt1", "interrupt2" or "interrupt3".
+
+  ranges: true
+
+  xlnx,aie-gen:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    description: |
+      hardware generation of AI engine device. E.g. the current values supported
+      are 1 and 2, it will be presented as <0x1> or <0x2>
+
+  xlnx,shim-rows:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      start row and the number of rows of SHIM tiles of the AI engine device
+
+  xlnx,core-rows:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      start row and the number of rows of core tiles of the AI engine device
+
+  xlnx,mem-rows:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      start row and the number of rows of memory tiles of the AI engine device
+
+required:
+  - compatible
+  - '#address-cells'
+  - '#size-cells'
+  - ranges
+  - power-domains
+  - xlnx,aie-gen
+  - xlnx,shim-rows
+  - xlnx,core-rows
+  - xlnx,mem-rows
+
+patternProperties:
+  "^aperture@[0-9]+$":
+    type: object
+    description: |
+      AI engine aperture which is a group of column based tiles of the
+      AI engine device. Each AI engine apertures isolated from the
+      other AI engine apertures. An AI engine aperture is defined by
+      Xilinx platform design tools.
+
+    properties:
+      reg:
+        description: |
+          Physical base address and length of the aperture registers.
+          The AI engine address space assigned to Linux is defined by Xilinx
+          platform design tool.
+
+      xlnx,columns:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        description:
+          It describes the location of the aperture. It specifies the start
+          column and the number of columns. E.g. an aperture starts from
+          column 0 and there are 50 columns, it will be presented as <0 50>.
+
+      interrupts:
+        maxItems: 3
+
+      interrupt-names:
+        description: |
+          Should be "interrupt1", "interrupt2" or "interrupt3".
+
+      xlnx,node-id:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: |
+          AI engine aperture node ID, which is defined by Xilinx platform design
+          tool to identify the AI engine aperture in the firmware.
+
+    required:
+      - reg
+      - xlnx,columns
+      - xlnx,node-id
+
+  "^partition[0-9]@[0-9]+$":
+    deprecated: true
+    type: object
+    description: |
+      AI engine partition which is a group of column based tiles of the AI
+      engine device. Each AI engine partition is isolated from the other
+      AI engine partitions. An AI engine partition is defined by Xilinx
+      platform design tools.
+      AI engine partition driver will create a FPGA bridge when probes the
+      AI engine partition. The AI engine SHIM row of the partition is the
+      bridge to connect AI engine partition, FPGA and PS.
+
+    properties:
+      reg:
+        description: |
+          It describes the group of tiles of the AI engine partition. It needs
+          to include the SHIM row. The format is defined by the parent AI engine
+          device node's '#address-cells' and '#size-cells' properties. e.g. a v1
+          AI engine device has 2D tiles array, the first row is SHIM row. A
+          partition which has 50 columns and 8 rows of core tiles and 1 row of
+          SHIM tiles will be presented as <0 0 50 9>.
+
+      label:
+        maxItems: 1
+
+      xlnx,partition-id:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: |
+          AI engine partition ID, which is defined by Xilinx platform design
+          tool to identify the AI engine partition in the system.
+
+    required:
+      - reg
+      - xlnx,partition-id
+
+additionalProperties: true
+
+examples:
+  - |
+    #include <dt-bindings/power/xlnx-versal-power.h>
+    bus {
+      #address-cells = <2>;
+      #size-cells = <2>;
+      ai_engine: ai_engine {
+        compatible = "xlnx,ai-engine-v2.0";
+        xlnx,aie-gen = /bits/ 8 <0x1>;
+        xlnx,shim-rows = /bits/ 8 <0 1>;
+        xlnx,core-rows = /bits/ 8 <1 8>;
+        xlnx,mem-rows = /bits/ 8 <0 0>;
+        power-domains = <&versal_firmware PM_DEV_AI>;
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges;
+
+        aperture0: aperture@0 {
+          /* 50 columns and 8 core tile rows + 1 SHIM row */
+          reg = <0x200 0x0 0x1 0x0>;
+          xlnx,columns = <0 50>;
+          xlnx,node-id = <1>;
+          interrupt-parent = <&gic>;
+          interrupts = <0x0 0x94 0x4>,
+                       <0x0 0x95 0x4>,
+                       <0x0 0x96 0x4>;
+          interrupt-names = "interrupt1", "interrupt2", "interrupt3";
+        };
+      };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/soc/xilinx/xlnx,ai_engine.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/soc/xilinx/xlnx,ai_engine.txt
@@ -0,0 +1,28 @@
+Xilinx AI Engine
+----------------
+
+The Xilinx AI Engine is a tile processor with many cores (up to 400) that
+can run in parallel. The data routing between cores is configured through
+internal switches, and shim tiles interface with external interconnect, such
+as memory or PL.
+
+Required properties:
+
+- compatible: Must be "xlnx,ai_engine".
+- reg: Physical base address and length of the registers set for the device.
+- interrupt-parent: the phandle to the interrupt controller.
+- interrupts: the interrupt numbers.
+- interrupt-names: Should be "interrupt0", "interrupt1", "interrupt2" or
+  "interrupt3".
+
+Example:
+
+	ai_engine@20000000000 {
+		compatible = "xlnx,ai_engine";
+		reg = <0x200 0x0 0x1 0x0>;
+		interrupt-parent = <&gic>;
+		interrupts = <0x0 0x94 0x1>,
+			     <0x0 0x95 0x1>,
+			     <0x0 0x96 0x1>;
+		interrupt-names = "interrupt1", "interrupt2", "interrupt3";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/amlogic,gx-sound-card.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/amlogic,gx-sound-card.yaml
@@ -61,7 +61,7 @@
         description: phandle of the CPU DAI
 
     patternProperties:
-      "^codec-[0-9]+$":
+      "^codec(-[0-9]+)?$":
         type: object
         description: |-
           Codecs:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/mt6359.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/mt6359.yaml
@@ -23,8 +23,8 @@
       Indicates how many data pins are used to transmit two channels of PDM
       signal. 0 means two wires, 1 means one wire. Default value is 0.
     enum:
-      - 0 # one wire
-      - 1 # two wires
+      - 0 # two wires
+      - 1 # one wire
 
   mediatek,mic-type-0:
     $ref: /schemas/types.yaml#/definitions/uint32
@@ -53,9 +53,9 @@
 
 examples:
   - |
-    mt6359codec: mt6359codec {
-      mediatek,dmic-mode = <0>;
-      mediatek,mic-type-0 = <2>;
+    mt6359codec: audio-codec {
+        mediatek,dmic-mode = <0>;
+        mediatek,mic-type-0 = <2>;
     };
 
 ...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt
@@ -109,7 +109,7 @@
 	reg  = <1 0>;
 	interrupts = <&msmgpio 54 IRQ_TYPE_LEVEL_HIGH>;
 	interrupt-names = "intr2"
-	reset-gpios = <&msmgpio 64 0>;
+	reset-gpios = <&msmgpio 64 GPIO_ACTIVE_LOW>;
 	slim-ifc-dev  = <&wc9335_ifd>;
 	clock-names = "mclk", "native";
 	clocks = <&rpmcc RPM_SMD_DIV_CLK1>,
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/rt5645.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/rt5645.txt
@@ -20,6 +20,11 @@
   a GPIO spec for the external headphone detect pin. If jd-mode = 0,
   we will get the JD status by getting the value of hp-detect-gpios.
 
+- cbj-sleeve-gpios:
+  a GPIO spec to control the external combo jack circuit to tie the sleeve/ring2
+  contacts to the ground or floating. It could avoid some electric noise from the
+  active speaker jacks.
+
 - realtek,in2-differential
   Boolean. Indicate MIC2 input are differential, rather than single-ended.
 
@@ -68,6 +73,7 @@
 	compatible = "realtek,rt5650";
 	reg = <0x1a>;
 	hp-detect-gpios = <&gpio 19 0>;
+	cbj-sleeve-gpios = <&gpio 20 0>;
 	interrupt-parent = <&gpio>;
 	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
 	realtek,dmic-en = "true";
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
@@ -113,8 +113,7 @@
           By default, custom protocol is assumed, meaning that protocol is
           configured according to protocol defined in related DAI link node,
           such as i2s, left justified, right justified, dsp and pdm protocols.
-        allOf:
-          - $ref: /schemas/types.yaml#/definitions/flag
+        $ref: /schemas/types.yaml#/definitions/flag
 
       "#clock-cells":
         description: Configure the SAI device as master clock provider.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/tas2562.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/tas2562.yaml
@@ -52,7 +52,9 @@
     description: TDM TX current sense time slot.
 
   '#sound-dai-cells':
-    const: 1
+    # The codec has a single DAI, the #sound-dai-cells=<1>; case is left in for backward
+    # compatibility but is deprecated.
+    enum: [0, 1]
 
 required:
   - compatible
@@ -69,7 +71,7 @@
      codec: codec@4c {
        compatible = "ti,tas2562";
        reg = <0x4c>;
-       #sound-dai-cells = <1>;
+       #sound-dai-cells = <0>;
        interrupt-parent = <&gpio1>;
        interrupts = <14>;
        shutdown-gpios = <&gpio1 15 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/tas2764.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/tas2764.yaml
@@ -46,7 +46,9 @@
     description: TDM TX voltage sense time slot.
 
   '#sound-dai-cells':
-    const: 1
+    # The codec has a single DAI, the #sound-dai-cells=<1>; case is left in for backward
+    # compatibility but is deprecated.
+    enum: [0, 1]
 
 required:
   - compatible
@@ -63,7 +65,7 @@
      codec: codec@38 {
        compatible = "ti,tas2764";
        reg = <0x38>;
-       #sound-dai-cells = <1>;
+       #sound-dai-cells = <0>;
        interrupt-parent = <&gpio1>;
        interrupts = <14>;
        reset-gpios = <&gpio1 15 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/tas2770.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/tas2770.yaml
@@ -54,7 +54,9 @@
       - 1 # Falling edge
 
   '#sound-dai-cells':
-    const: 1
+    # The codec has a single DAI, the #sound-dai-cells=<1>; case is left in for backward
+    # compatibility but is deprecated.
+    enum: [0, 1]
 
 required:
   - compatible
@@ -71,7 +73,7 @@
      codec: codec@41 {
        compatible = "ti,tas2770";
        reg = <0x41>;
-       #sound-dai-cells = <1>;
+       #sound-dai-cells = <0>;
        interrupt-parent = <&gpio1>;
        interrupts = <14>;
        reset-gpio = <&gpio1 15 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
@@ -176,13 +176,12 @@
        4 - Drive weak low and active high
        5 - Drive Hi-Z and active high
 
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32-array
-      - minItems: 2
-        maxItems: 2
-        items:
-          maximum: 15
-        default: [2, 2]
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 2
+    items:
+      maximum: 15
+    default: [2, 2]
 
 required:
   - compatible
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
@@ -1,6 +1,6 @@
 Device-Tree bindings for Xilinx PL audio formatter
 
-The IP core supports DMA, data formatting(AES<->PCM conversion)
+The IP core supports DMA, data formatting(packing, conversion)
 of audio samples.
 
 Required properties:
@@ -13,8 +13,21 @@
  - interrupts-parent: Phandle for interrupt controller.
  - interrupts: List of Interrupt numbers.
  - reg: Base address and size of the IP core instance.
+ - xlnx,tx: connected audio sink node.
+	    Should be one of below supported nodes:
+		1. HDMI video Tx output
+		2. I2S transmitter
+		3. UHDSDI audio embed
+	    Only those nodes were supported in sound card driver
+
+ - xlnx,rx: connected audio source node.
+	    Should be one of below supported nodes:
+		1. HDMI video Rx input
+		2. I2S receiver
+		3. UHDSDI audio extract
+	    Only those nodes were supported in sound card driver
  - clock-names: List of input clocks.
-   Required elements: "s_axi_lite_aclk", "aud_mclk"
+   Required elements: "s_axi_lite_aclk", "m_axis_mm2s_aclk", "aud_mclk", "s_axis_s2mm_aclk"
  - clocks: Input clock specifier. Refer to common clock bindings.
 
 Example:
@@ -24,6 +37,8 @@
 		interrupt-parent = <&gic>;
 		interrupts = <0 104 4>, <0 105 4>;
 		reg = <0x0 0x80010000 0x0 0x1000>;
-		clock-names = "s_axi_lite_aclk", "aud_mclk";
-		clocks = <&clk 71>, <&clk_wiz_1 0>;
+		xlnx,tx = <&i2s_transmitter>;
+		xlnx,rx = <&i2s_receiver>;
+		clock-names = "s_axi_lite_aclk", "m_axis_mm2s_aclk", "aud_mclk", "s_axis_s2mm_aclk";
+		clocks = <&clk 71>, <&audio_ss_0_clk_wiz_0 0>, <&audio_ss_0_clk_wiz_0 0>, <&clk 71>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,dp-snd-card.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,dp-snd-card.txt
@@ -0,0 +1,17 @@
+Device-Tree bindings for Xilinx ZynqMP DisplayPort Audio Card
+
+The card driver integrates codec and pcm components and represents as a single
+audio device.
+
+Required properties:
+ - compatible: Should be "xlnx,dp-snd-card".
+ - xlnx,dp-snd-pcm: phandle(s) to the ZynqMP DP PCM node.
+ - xlnx,dp-snd-codec: phandle to the ZynqMP DP card node.
+
+Example:
+
+	xlnx_dp_snd_card: dp_snd_card {
+		compatible = "xlnx,dp-snd-card";
+		xlnx,dp-snd-pcm = <&xlnx_dp_snd_pcm0>, <&xlnx_dp_snd_pcm1>;
+		xlnx,dp-snd-codec = <&xlnx_dp_snd_codec0>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,dp-snd-codec.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,dp-snd-codec.txt
@@ -0,0 +1,18 @@
+Device-Tree bindings for Xilinx ZynqMP DisplayPort Codec
+
+The codec driver handles the audio clock and format management.
+
+Required properties:
+ - compatible: Should be "xlnx,dp-snd-codec".
+ - clocks: The phandle for the audio clock. The audio clock should be
+   configured to the correct audio clock rate, which should be one of
+   (44100 * 512) or (48000 * 512).
+ - clock-names: The identification string should be "aud_clk".
+
+Example:
+
+	xlnx_dp_snd_codec0: dp_snd_codec0 {
+		compatible = "xlnx,dp-snd-codec";
+		clocks = <&dp_aud_clk>;
+		clock-names = "aud_clk";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,dp-snd-pcm.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,dp-snd-pcm.txt
@@ -0,0 +1,18 @@
+Device-Tree bindings for Xilinx ZynqMP DisplayPort PCM
+
+The DPDMA driver of ZynqMP DisplayPort subsystem is based on DMA engine,
+and the DP PCM driver is based on snd dmaengine helpers.
+
+Required properties:
+ - compatible: Should be "xlnx,dp-snd-pcm" or "xlnx,dp-snd-pcm0" or "xlnx,dp-snd-pcm1".
+ - dmas: the phandle list of DMA specifiers. The dma channel ID should be one
+   of 4 for audio0 channel or 5 for audio1 channel.
+ - dma-names: the indentifier strings for DMAs. The value should be "tx".
+
+Example:
+
+	xlnx_dp_snd_pcm0: dp_snd_pcm0 {
+		compatible = "xlnx,dp-snd-pcm0";
+		dmas = <&xlnx_dpdma 4>;
+		dma-names = "tx";
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,i2s.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,i2s.txt
@@ -11,18 +11,31 @@
  - xlnx,dwidth: sample data width. Can be any of 16, 24.
  - xlnx,num-channels: Number of I2S streams. Can be any of 1, 2, 3, 4.
 		      supported channels = 2 * xlnx,num-channels
+ - xlnx,snd-pcm: reference to audio formatter block
+ - clock-names: List of input clocks.
+   Required elements for I2S Tx: "s_axi_ctrl_aclk", "aud_mclk", "s_axis_aud_aclk".
+   Required elements for I2S Rx: "s_axi_ctrl_aclk", "aud_mclk", "m_axis_aud_aclk".
+ - clocks: Input clock specifier. Refer to common clock bindings.
 
 Example:
 
 	i2s_receiver@a0080000 {
 		compatible = "xlnx,i2s-receiver-1.0";
+		clock-names = "s_axi_ctrl_aclk", "aud_mclk", "m_axis_aud_aclk";
+		clocks = <&clk 71>, <&audio_ss_0_clk_wiz_0 0>, <&clk 71>;
 		reg = <0x0 0xa0080000 0x0 0x10000>;
 		xlnx,dwidth = <0x18>;
 		xlnx,num-channels = <1>;
+		xlnx,snd-pcm = <&audio_ss_0_audio_formatter_0>;
 	};
 	i2s_transmitter@a0090000 {
 		compatible = "xlnx,i2s-transmitter-1.0";
+		clock-names = "s_axi_ctrl_aclk", "aud_mclk", "s_axis_aud_aclk";
+		clocks = <&clk 71>, <&audio_ss_0_clk_wiz_0 0>, <&audio_ss_0_clk_wiz_0 0>;
 		reg = <0x0 0xa0090000 0x0 0x10000>;
 		xlnx,dwidth = <0x18>;
 		xlnx,num-channels = <1>;
+		xlnx,snd-pcm = <&audio_ss_0_audio_formatter_0>;
 	};
+	Documentation of "audio_ss_0_audio_formatter_0" node is located
+	at Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,spdif.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,spdif.txt
@@ -1,28 +1,27 @@
-Device-Tree bindings for Xilinx SPDIF IP
+Device-Tree bindings for Xilinx SPDIF PL IP
 
-The IP supports playback and capture of SPDIF audio
+The IP supports SPDIF based playback and capture audio
 
 Required properties:
  - compatible: "xlnx,spdif-2.0"
  - clock-names: List of input clocks.
-   Required elements: "s_axi_aclk", "aud_clk_i"
+   Required elements for SPDIF Tx: "aud_clk_i", "s_axi_aclk", "s_axis_aclk".
+   Required elements for SPDIF Rx: "aud_clk_i", "s_axi_aclk", "m_axis_aclk".
  - clocks: Input clock specifier. Refer to common clock bindings.
  - reg: Base address and address length of the IP core instance.
  - interrupts-parent: Phandle for interrupt controller.
  - interrupts: List of Interrupt numbers.
- - xlnx,spdif-mode: 0 :- receiver mode
-		    1 :- transmitter mode
- - xlnx,aud_clk_i: input audio clock value.
+ - xlnx,spdif-mode: 0 :- receiver mode ; 1 :- transmitter mode
+ - xlnx,snd-pcm: phandle to audio formatter node
 
-Example:
+Example - SPDIF Rx:
 	spdif_0: spdif@80010000 {
-		clock-names = "aud_clk_i", "s_axi_aclk";
-		clocks = <&misc_clk_0>, <&clk 71>;
+		clock-names = "aud_clk_i", "s_axi_aclk", "m_axis_aclk";
+		clocks = <&si570_1>, <&clk 71>, <&clk 71>;
 		compatible = "xlnx,spdif-2.0";
-		interrupt-names = "spdif_interrupt";
 		interrupt-parent = <&gic>;
 		interrupts = <0 91 4>;
 		reg = <0x0 0x80010000 0x0 0x10000>;
 		xlnx,spdif-mode = <1>;
-		xlnx,aud_clk_i = <49152913>;
+		xlnx,snd-pcm = <&audio_formatter_0>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/sound/xlnx,v-uhdsdi-audio.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/sound/xlnx,v-uhdsdi-audio.txt
@@ -0,0 +1,60 @@
+Device-Tree bindings for Xilinx SDI audio
+
+The IP core supports embed/extract of audio in SDI Tx and Rx
+protocol respectively. Reference to PG:
+https://www.xilinx.com/support/documentation/ip_documentation/v_uhdsdi_audio/v1_0/pg309-v-uhdsdi-audio.pdf
+
+Required properties:
+ - compatible: Should be one of:
+		"xlnx,v-uhdsdi-audio-2.0"
+		"xlnx,v-uhdsdi-audio-1.0"
+   Note: v1.0 (xlnx,v-uhdsdi-audio-1.0) is deprecated
+   and driver no longer supports it. Mandatory to upgrade to v2.0
+ - interrupts: Interrupt number.
+ - interrupts-parent: phandle for interrupt controller.
+ - reg: Base address and size of the IP core instance.
+ - xlnx,snd-pcm: reference to audio formatter block
+ - clock-names: List of input clocks.
+   Required elements for SDI Embed: "s_axi_aclk", "s_axis_clk", "sdi_embed_clk".
+   Required elements for SDI Extract: "s_axi_aclk", "sdi_extract_clk", "m_axis_clk".
+ - clocks: Input clock specifier. Refer to common clock bindings.
+
+SDI embed contains a output port to remote endpoint of SDI video Tx node.
+This pipeline should be described using the DT bindings defined in
+Documentation/devicetree/bindings/graph.txt
+
+Example:
+
+	audio_ss_0_v_uhdsdi_audio_extract_0: v_uhdsdi_audio@80080000 {
+		compatible = "xlnx,v-uhdsdi-audio-2.0";
+		clock-names = "s_axi_aclk", "sdi_extract_clk", "m_axis_clk";
+		clocks = <&misc_clk_0>, <&misc_clk_1>, <&misc_clk_0>;
+		interrupt-names = "interrupt";
+		interrupt-parent = <&gic>;
+		interrupts = <0 106 4>;
+		reg = <0x0 0x80080000 0x0 0x10000>;
+		xlnx,snd-pcm = <&audio_ss_0_audio_formatter_0>;
+	};
+
+	audio_ss_0_v_uhdsdi_audio_embed_0: v_uhdsdi_audio@80090000 {
+		compatible = "xlnx,v-uhdsdi-audio-2.0";
+		clock-names = "s_axi_aclk", "s_axis_clk", "sdi_embed_clk";
+		clocks = <&misc_clk_0>, <&misc_clk_0>, <&misc_clk_1>;
+		interrupt-names = "interrupt";
+		interrupt-parent = <&gic>;
+		interrupts = <0 107 4>;
+		reg = <0x0 0x80090000 0x0 0x10000>;
+		xlnx,snd-pcm = <&audio_ss_0_audio_formatter_0>;
+		sdi_av_port: port@0 {
+			reg = <0>;
+			sditx_audio_embed_src: endpoint {
+				remote-endpoint = <&sdi_audio_sink_port>;
+			};
+		};
+	};
+
+	Node 'v_smpte_uhdsdi_tx_ss' is documented in SDI Tx video bindings,
+	located at Documentation/devicetree/bindings/display/xlnx/xlnx,sdi-tx.txt.
+
+	Node 'audio_ss_0_audio_formatter_0' node is documented
+	at Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
@@ -11,6 +11,14 @@
 
 allOf:
   - $ref: spi-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: xlnx,versal-ospi-1.0
+    then:
+      required:
+        - power-domains
 
 properties:
   compatible:
@@ -20,6 +28,7 @@
               - ti,k2g-qspi
               - ti,am654-ospi
               - intel,lgm-qspi
+              - xlnx,versal-ospi-1.0
           - const: cdns,qspi-nor
       - const: cdns,qspi-nor
 
@@ -65,6 +74,9 @@
       data rather than the QSPI clock. Make sure that QSPI return clock
       is populated on the board before using this property.
 
+  power-domains:
+    maxItems: 1
+
   resets:
     maxItems: 2
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
@@ -106,7 +106,7 @@
             dma-names = "rx", "tx";
 
             flash@0 {
-                    compatible = "spi-nor";
+                    compatible = "jedec,spi-nor";
                     reg = <0>;
                     spi-max-frequency = <104000000>;
                     spi-tx-bus-width = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
@@ -45,6 +45,7 @@
     maxItems: 2
 
   interconnect-names:
+    minItems: 1
     items:
       - const: qspi-config
       - const: qspi-memory
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/spi-cadence.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/spi-cadence.yaml
@@ -49,6 +49,13 @@
     enum: [ 0, 1 ]
     default: 0
 
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clock-names
+  - clocks
+
 unevaluatedProperties: false
 
 examples:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/spi-controller.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/spi-controller.yaml
@@ -93,74 +93,7 @@
 patternProperties:
   "^.*@[0-9a-f]+$":
     type: object
-
-    properties:
-      compatible:
-        description:
-          Compatible of the SPI device.
-
-      reg:
-        minItems: 1
-        maxItems: 256
-        items:
-          minimum: 0
-          maximum: 256
-        description:
-          Chip select used by the device.
-
-      spi-3wire:
-        $ref: /schemas/types.yaml#/definitions/flag
-        description:
-          The device requires 3-wire mode.
-
-      spi-cpha:
-        $ref: /schemas/types.yaml#/definitions/flag
-        description:
-          The device requires shifted clock phase (CPHA) mode.
-
-      spi-cpol:
-        $ref: /schemas/types.yaml#/definitions/flag
-        description:
-          The device requires inverse clock polarity (CPOL) mode.
-
-      spi-cs-high:
-        $ref: /schemas/types.yaml#/definitions/flag
-        description:
-          The device requires the chip select active high.
-
-      spi-lsb-first:
-        $ref: /schemas/types.yaml#/definitions/flag
-        description:
-          The device requires the LSB first mode.
-
-      spi-max-frequency:
-        $ref: /schemas/types.yaml#/definitions/uint32
-        description:
-          Maximum SPI clocking speed of the device in Hz.
-
-      spi-rx-bus-width:
-        description:
-          Bus width to the SPI bus used for read transfers.
-          If 0 is provided, then no RX will be possible on this device.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1, 2, 4, 8]
-        default: 1
-
-      spi-rx-delay-us:
-        description:
-          Delay, in microseconds, after a read transfer.
-
-      spi-tx-bus-width:
-        description:
-          Bus width to the SPI bus used for write transfers.
-          If 0 is provided, then no TX will be possible on this device.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1, 2, 4, 8]
-        default: 1
-
-      spi-tx-delay-us:
-        description:
-          Delay, in microseconds, after a write transfer.
+    $ref: spi-peripheral-props.yaml
 
     required:
       - compatible
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/spi-mxic.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/spi-mxic.txt
@@ -8,11 +8,13 @@
 - reg: should contain 2 entries, one for the registers and one for the direct
        mapping area
 - reg-names: should contain "regs" and "dirmap"
-- interrupts: interrupt line connected to the SPI controller
 - clock-names: should contain "ps_clk", "send_clk" and "send_dly_clk"
 - clocks: should contain 3 entries for the "ps_clk", "send_clk" and
 	  "send_dly_clk" clocks
 
+Optional properties:
+- interrupts: interrupt line connected to the SPI controller
+
 Example:
 
 	spi@43c30000 {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-peripheral-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral-specific properties for a SPI bus.
+
+description:
+  Many SPI controllers need to add properties to peripheral devices. They could
+  be common properties like spi-max-frequency, spi-cpha, etc. or they could be
+  controller specific like delay in clock or data lines, etc. These properties
+  need to be defined in the peripheral node because they are per-peripheral and
+  there can be multiple peripherals attached to a controller. All those
+  properties are listed here. The controller specific properties should go in
+  their own separate schema that should be referenced from here.
+
+maintainers:
+  - Pratyush Yadav <p.yadav@ti.com>
+
+properties:
+  reg:
+    minItems: 1
+    maxItems: 256
+    items:
+      minimum: 0
+      maximum: 256
+    description:
+      Chip select used by the device.
+
+  spi-3wire:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires 3-wire mode.
+
+  spi-cpha:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires shifted clock phase (CPHA) mode.
+
+  spi-cpol:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires inverse clock polarity (CPOL) mode.
+
+  spi-cs-high:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires the chip select active high.
+
+  spi-lsb-first:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The device requires the LSB first mode.
+
+  spi-max-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Maximum SPI clocking speed of the device in Hz.
+
+  spi-rx-bus-width:
+    description:
+      Bus width to the SPI bus used for read transfers.
+      If 0 is provided, then no RX will be possible on this device.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 4, 8]
+    default: 1
+
+  spi-rx-delay-us:
+    description:
+      Delay, in microseconds, after a read transfer.
+
+  spi-tx-bus-width:
+    description:
+      Bus width to the SPI bus used for write transfers.
+      If 0 is provided, then no TX will be possible on this device.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 4, 8]
+    default: 1
+
+  spi-tx-delay-us:
+    description:
+      Delay, in microseconds, after a write transfer.
+
+# The controller specific properties go here.
+
+additionalProperties: true
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml
@@ -14,7 +14,11 @@
 
 properties:
   compatible:
-    const: xlnx,zynqmp-qspi-1.0
+    oneOf:
+      - items:
+          - enum:
+              - xlnx,zynqmp-qspi-1.0
+              - xlnx,versal-qspi-1.0
 
   reg:
     maxItems: 2
@@ -30,6 +34,13 @@
   clocks:
     maxItems: 2
 
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clock-names
+  - clocks
+
 unevaluatedProperties: false
 
 examples:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/staging/net/xilinx-tsn-ethernet.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/staging/net/xilinx-tsn-ethernet.txt
@@ -0,0 +1,54 @@
+Xilinx TSN (time sensitive networking) TEMAC axi ethernet driver (xilinx_axienet)
+-----------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,tsn-ethernet-1.00.a".
+- reg			: Physical base address and size of the TSN registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupts-names	: Property denotes the interrupt names.
+- interrupt-parent	: Must be core interrupt controller.
+- phy-handle		: See ethernet.txt file [1].
+- local-mac-address	: See ethernet.txt file [1].
+- phy-mode		: see ethernet.txt file [1].
+
+Optional properties:
+- xlnx,tsn		: Denotes a ethernet with TSN capabilities.
+- xlnx,tsn-slave	: Denotes a TSN slave port.
+- xlnx,txcsum		: Tx checksum mode (Full, Partial and None).
+- xlnx,rxcsum		: Rx checksum mode (Full, Partial and None).
+- xlnx,phy-type		: Xilinx phy device type. See xilinx-phy.txt [2].
+- xlnx,eth-hasnobuf	: Used when 1G MAC is configured in non-processor mode.
+- xlnx,num-queue	: Number of queue supported in current design, range is
+			  2 to 5 and default value is 5.
+- xlnx,num-tc		: Number of traffic class supported in current design,
+			  range is 2,3 and default value is 3. It denotes
+			  the traffic classes based on VLAN-PCP value.
+- xlnx,qbv-addr		: Denotes mac scheduler physical base address.
+- xlnx,qbv-size		: Denotes mac scheduler address space size.
+
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+[2] Documentation/devicetree/bindings/net/xilinx-phy.txt
+
+Example:
+
+	tsn_emac_0: tsn_mac@80040000 {
+		compatible = "xlnx,tsn-ethernet-1.00.a";
+		interrupt-parent = <&gic>;
+		interrupts = <0 104 4 0 106 4 0 91 4 0 110 4>;
+		interrupt-names = "interrupt_ptp_rx_1", "interrupt_ptp_tx_1", "mac_irq_1", "interrupt_ptp_timer";
+		local-mac-address = [ 00 0A 35 00 01 0e ];
+		phy-mode = "rgmii";
+		reg = <0x0 0x80040000 0x0 0x14000>;
+		tsn,endpoint = <&tsn_ep>;
+		xlnx,tsn;
+		xlnx,tsn-slave;
+		xlnx,phy-type = <0x3>;
+		xlnx,eth-hasnobuf;
+		xlnx,num-queue = <0x2>;
+		xlnx,num-tc = <0x3>;
+		xlnx,qbv-addr = <0x80054000>;
+		xlnx,qbv-size = <0x2000>;
+		xlnx,txsum = <0>;
+		xlnx,rxsum = <0>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/staging/net/xilinx_tsn.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/staging/net/xilinx_tsn.txt
@@ -0,0 +1,14 @@
+Xilinx TSN (time sensitive networking) IP driver (xilinx_tsn_ip)
+-----------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be one of "xlnx,tsn-endpoint-ethernet-mac-1.0",
+			  "xlnx,tsn-endpoint-ethernet-mac-2.0" for TSN.
+- reg			: Physical base address and size of the TSN registers map.
+
+Example:
+
+	tsn_endpoint_ip_0: tsn_endpoint_ip_0 {
+		compatible = "xlnx,tsn-endpoint-ethernet-mac-2.0";
+		reg = <0x0 0x80040000 0x0 0x40000>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/staging/net/xilinx_tsn_ep.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/staging/net/xilinx_tsn_ep.txt
@@ -0,0 +1,51 @@
+Xilinx TSN (time sensitive networking) EndPoint Driver (xilinx_tsn_ep)
+-------------------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,tsn-ep"
+- reg			: Physical base address and size of the TSN Endpoint
+				registers map
+- interrupts		: Property with a value describing the interrupt
+- interrupts-names	: Property denotes the interrupt names.
+- interrupt-parent	: Must be core interrupt controller.
+- local-mac-address	: See ethernet.txt [1].
+
+Optional properties:
+- xlnx,num-tc		: Number of traffic class supported in current design,
+			  range is 2,3 and default value is 3. It denotes
+			  the traffic classes based on VLAN-PCP value.
+- xlnx,channel-ids 	: Queue Identifier associated with the MCDMA Channel, range
+			  is Tx: "1 to 2" and Rx: "2 to 5", default value is "1 to 5".
+- xlnx,eth-hasnobuf	: Used when 1G MAC is configured in non processor mode.
+- axistream-connected-rx	: Reference to another node which contains the
+				  resources for the MCDMA controller used by
+				  this device. The MCDMA related resources
+				  (registers and interrupts) will be used from
+				  this node.
+
+Optional TADMA properties:
+- xlnx,num-buffers-per-stream	: Number of TADMA buffers per stream in design. Default is 64.
+- xlnx,num-streams		: Number of streams. Default is 8.
+- xlnx,num-fetch-entries	: Maximum number of entries that can be programmed to be
+				  fetched by TADMA. Default is 8.
+- axistream-connected-tx	: Reference to another node which contains the
+				  resources for the TADMA controller used by
+				  this device. The TADMA-related resources
+				  (registers and interrupts) will be used from
+				  this node.
+
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+
+Example:
+
+	tsn_ep: tsn_ep@80056000 {
+		compatible = "xlnx,tsn-ep";
+		reg = <0x0 0x80056000 0x0 0xA000>;
+		xlnx,num-tc = <0x3>;
+		interrupt-names = "tsn_ep_scheduler_irq";
+		interrupt-parent = <&gic>;
+		interrupts = <0 111 4>;
+		local-mac-address = [00 0A 35 00 01 10];
+		xlnx,channel-ids = "1","2","3","4","5";
+		xlnx,eth-hasnobuf ;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/staging/net/xilinx_tsn_ep_ex.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/staging/net/xilinx_tsn_ep_ex.txt
@@ -0,0 +1,26 @@
+Xilinx TSN (time sensitive networking) Extended EndPoint Driver (xilinx_tsn_ep_ex)
+-------------------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,tsn-ex-ep"
+- reg			: Physical base address and size of the TSN Endpoint
+				registers map
+- local-mac-address	: See ethernet.txt [1].
+
+Optional properties:
+- packet-switch		: set to 1 when packet switching on ex-ep is
+			  enabled in the design.
+- tsn,endpoint		: This is a handle to the endpoint node.
+			  The necessary ep resource details are obtained
+			  from this reference.
+
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+
+Example:
+
+	tsn_ep_ex: tsn_ep_ex@80056000 {
+		compatible = "xlnx,tsn-ex-ep";
+		reg = <0x0 0x80056000 0x0 0xA000>;
+		local-mac-address = [00 0A 35 00 01 20];
+		tsn,endpoint = <&tsn_ep>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/staging/net/xilinx_tsn_switch.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/staging/net/xilinx_tsn_switch.txt
@@ -0,0 +1,26 @@
+Xilinx TSN (time sensitive networking) Switch Driver (xilinx_tsn_switch)
+-----------------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,tsn-switch"
+- reg			: Physical base address and size of the TSN registers map.
+- xlnx,num-ports	: Number of network ports in subsystems. For ex., for an
+			  EP + Switch system to two TEMACs, this value should be 3
+			  (ep, temac1 and temac 2).
+
+Optional properties:
+- xlnx,num-tc		: Number of traffic class supported in current design,
+			  range is 2,3 and default value is 3. It denotes
+			  the traffic classes based on VLAN-PCP value.
+- xlnx,has-hwaddr-learning	: Denotes hardware address learning support
+- xlnx,has-inband-mgmt-tag	: Denotes inband management support
+
+Example:
+
+	epswitch: tsn_switch@80078000 {
+		compatible = "xlnx,tsn-switch";
+		reg = <0x0 0x80078000 0x0 0x4000>;
+		xlnx,num-tc = <0x3>;
+		xlnx,has-hwaddr-learning ;
+		xlnx,has-inband-mgmt-tag ;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/thermal/thermal-zones.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/thermal/thermal-zones.yaml
@@ -49,7 +49,10 @@
       to take when the temperature crosses those thresholds.
 
 patternProperties:
-  "^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$":
+  # Node name is limited in size due to Linux kernel requirements - 19
+  # characters in total (see THERMAL_NAME_LENGTH, including terminating NUL
+  # byte):
+  "^[a-zA-Z][a-zA-Z0-9\\-]{1,10}-thermal$":
     type: object
     description:
       Each thermal zone node contains information about how frequently it
@@ -199,12 +202,11 @@
 
               contribution:
                 $ref: /schemas/types.yaml#/definitions/uint32
-                minimum: 0
-                maximum: 100
                 description:
-                  The percentage contribution of the cooling devices at the
-                  specific trip temperature referenced in this map
-                  to this thermal zone
+                  The cooling contribution to the thermal zone of the referred
+                  cooling device at the referred trip point. The contribution is
+                  a ratio of the sum of all cooling contributions within a
+                  thermal zone.
 
             required:
               - trip
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/timer/cdns,ttc.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/timer/cdns,ttc.yaml
@@ -30,12 +30,26 @@
     description: |
       Bit width of the timer, necessary if not 16.
 
+  "#pwm-cells":
+    description: |
+      Required to configure TTC as PWM device, supported cells are 0 to 3.
+    minimum: 0
+    maximum: 3
+
 required:
   - compatible
   - reg
-  - interrupts
   - clocks
 
+allOf:
+  - if:
+      not:
+        required:
+          - "#pwm-cells"
+    then:
+      required:
+        - interrupts
+
 additionalProperties: false
 
 examples:
@@ -48,3 +62,12 @@
         clocks = <&cpu_clk 3>;
         timer-width = <32>;
     };
+
+  - |
+    ttc1: ttc1@f8002000 {
+        compatible = "cdns,ttc";
+        reg = <0xF8002000 0x1000>;
+        clocks = <&cpu_clk 3>;
+        timer-width = <32>;
+        #pwm-cells = <3>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/cdns,usb3.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/cdns,usb3.yaml
@@ -64,7 +64,7 @@
     description:
       size of memory intended as internal memory for endpoints
       buffers expressed in KB
-    $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint16
 
   cdns,phyrst-a-enable:
     description: Enable resetting of PHY if Rx fail is detected
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/dwc3-xilinx.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/dwc3-xilinx.yaml
@@ -0,0 +1,131 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/dwc3-xilinx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx SuperSpeed DWC3 USB SoC controller
+
+maintainers:
+  - Manish Narani <manish.narani@xilinx.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - xlnx,zynqmp-dwc3
+          - xlnx,versal-dwc3
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    enum: [ 1, 2 ]
+
+  "#size-cells":
+    enum: [ 1, 2 ]
+
+  ranges: true
+
+  power-domains:
+    description: specifies a phandle to PM domain provider node
+    maxItems: 1
+
+  clocks:
+    description:
+      A list of phandle and clock-specifier pairs for the clocks
+      listed in clock-names.
+    items:
+      - description: Master/Core clock, has to be >= 125 MHz
+          for SS operation and >= 60MHz for HS operation.
+      - description: Clock source to core during PHY power down.
+
+  clock-names:
+    items:
+      - const: bus_clk
+      - const: ref_clk
+
+  resets:
+    description:
+      A list of phandles for resets listed in reset-names.
+
+    items:
+      - description: USB core reset
+      - description: USB hibernation reset
+      - description: USB APB reset
+
+  reset-names:
+    items:
+      - const: usb_crst
+      - const: usb_hibrst
+      - const: usb_apbrst
+
+  reset-gpio:
+    description: Specifies a mode-pin GPIO for reset
+    maxItems: 1
+
+  phys:
+    minItems: 1
+    maxItems: 2
+
+  phy-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      enum:
+        - usb2-phy
+        - usb3-phy
+
+# Required child node:
+
+patternProperties:
+  "^usb@[0-9a-f]+$":
+    $ref: snps,dwc3.yaml#
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+  - power-domains
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/power/xlnx-zynqmp-power.h>
+    #include <dt-bindings/reset/xlnx-zynqmp-resets.h>
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+    #include <dt-bindings/reset/xlnx-zynqmp-resets.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/phy/phy.h>
+
+    usb@ff9d0000 {
+        #address-cells = <0x1>;
+        #size-cells = <0x1>;
+        compatible = "xlnx,zynqmp-dwc3";
+        reg = <0xff9d0000 0x100>;
+        clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+        clock-names = "bus_clk", "ref_clk";
+        power-domains = <&zynqmp_firmware PD_USB_0>;
+        resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
+                 <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
+                 <&zynqmp_reset ZYNQMP_RESET_USB1_APB>;
+        reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
+        reset-gpio = <&modepin_gpio 1 GPIO_ACTIVE_LOW>;
+        phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+        phy-names = "usb3-phy";
+        ranges;
+
+        usb@fe200000 {
+            compatible = "snps,dwc3";
+            reg = <0xfe200000 0x40000>;
+            interrupt-names = "dwc_usb3", "otg", "hiber";
+            interrupts = <0 65 4>, <0 69 4>, <0 75 4>;
+            dr_mode = "host";
+        };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/ehci-xilinx.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/ehci-xilinx.txt
@@ -0,0 +1,21 @@
+Xilinx USB EHCI controller
+
+Required properties:
+- compatible: must be "xlnx,xps-usb-host-1.00.a"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The EHCI interrupt
+
+Optional properties:
+- xlnx,ext-vbus-valid: Use external VBUS
+- xlnx,support-usb-fs: Support for Full Speed USB
+- xlnx,use-phy-bus-pwr: Use phy bus power in USB
+
+Example:
+
+	xps_usb_host_0: usb@82400000 {
+		compatible = "xlnx,xps-usb-host-1.00.a";
+		interrupt-parent = <&xps_intc_0>;
+		interrupts = < 0 2 >;
+		reg = < 0x82400000 0x200 >;
+	} ;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/generic-ehci.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/generic-ehci.yaml
@@ -135,7 +135,8 @@
       Phandle of a companion.
 
   phys:
-    maxItems: 1
+    minItems: 1
+    maxItems: 3
 
   phy-names:
     const: usb
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/generic-ohci.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/generic-ohci.yaml
@@ -102,7 +102,8 @@
       Overrides the detected port count
 
   phys:
-    maxItems: 1
+    minItems: 1
+    maxItems: 3
 
   phy-names:
     const: usb
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -56,6 +56,7 @@
       - description: optional, wakeup interrupt used to support runtime PM
 
   interrupt-names:
+    minItems: 1
     items:
       - const: host
       - const: wakeup
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/microchip,usb2244.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/microchip,usb2244.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/usb/microchip,usb2244.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Bindings for the Microchip USB2244 Ultra Fast USB-SD Controller
+
+description:
+  Microchip’s USB224x is a USB 2.0 compliant, Hi-Speed bulk only mass
+  storage class peripheral controller intended for reading and writing
+  to popular flash media from the xDPicture Card™, Memory Stick® (MS),
+  Secure Digital (SD), and MultiMediaCard™ (MMC) families.
+
+  USB224x is a flash media card reader solution fully compliant with the
+  USB 2.0 specification
+
+maintainers:
+  - Piyush Mehta <piyush.mehta@xilinx.com>
+
+properties:
+  compatible:
+    const: microchip,usb2244
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      The phandle and specifier for the GPIO that controls the RESET line of
+      flash media controller.
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    usb {
+       compatible = "microchip,usb2244";
+       reset-gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/usb/microchip,usb5744.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Bindings for the Microchip USB5744 4-port Hub Controller
+
+description:
+  Microchip’s USB5744 SmartHub™ IC is a 4 port, SuperSpeed (SS)/Hi-Speed (HS),
+  low power, low pin count configurable and fully compliant with the USB 3.1
+  Gen 1 specification. The USB5744 also supports Full Speed (FS) and Low Speed
+  (LS) USB signaling, offering complete coverage of all defined USB operating
+  speeds. The new SuperSpeed hubs operate in parallel with the USB 2.0
+  controller, so 5 Gbps SuperSpeed data transfers are not affected by slower
+  USB 2.0 traffic.
+
+maintainers:
+  - Piyush Mehta <piyush.mehta@xilinx.com>
+  - Michal Simek <michal.simek@xilinx.com>
+
+properties:
+  compatible:
+    const: microchip,usb5744
+
+  reg:
+    maxItems: 1
+    description: |
+      Specifies the i2c slave address, it is required and should be 0x2d
+      if I2C is used.
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      The phandle and specifier for the GPIO that controls the RESET line of
+      USB hub.
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        usb5744@2d {
+            compatible = "microchip,usb5744";
+            reg = <0x2d>;
+            reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+        };
+    };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
@@ -50,6 +50,8 @@
       - const: dwc_usb3
       - items:
           enum: [host, peripheral, otg]
+      - items:
+          enum: [dwc_usb3, otg, hiber]
 
   clocks:
     description:
@@ -240,7 +242,7 @@
     description:
       High-Speed PHY interface selection between UTMI+ and ULPI when the
       DWC_USB3_HSPHY_INTERFACE has value 3.
-    $ref: /schemas/types.yaml#/definitions/uint8
+    $ref: /schemas/types.yaml#/definitions/string
     enum: [utmi, ulpi]
 
   snps,quirk-frame-length-adjustment:
@@ -252,6 +254,13 @@
     minimum: 0
     maximum: 0x3f
 
+  snps,xhci-reset-on-resume:
+    description:
+      When set, xhci host will reset the host controller on resume from
+      suspend. Some controllers might lose power during suspend, so host
+      require re-initialization.
+    type: boolean
+
   snps,rx-thr-num-pkt-prd:
     description:
       Periodic ESS RX packet threshold count (host mode only). Set this and
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/st,stusb160x.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/st,stusb160x.yaml
@@ -32,9 +32,7 @@
 
   connector:
     type: object
-
-    allOf:
-      - $ref: ../connector/usb-connector.yaml
+    $ref: /schemas/connector/usb-connector.yaml#
 
     properties:
       compatible:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/udc-xilinx.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/udc-xilinx.txt
@@ -6,13 +6,16 @@
 			  device registers map.
 - interrupts		: Should contain single irq line of USB2 device
 			  controller
-- xlnx,has-builtin-dma	: if DMA is included
+- xlnx,has-builtin-dma	: If DMA is included
 
-Example:
- 		axi-usb2-device@42e00000 {
-                        compatible = "xlnx,usb2-device-4.00.a";
-                        interrupts = <0x0 0x39 0x1>;
-                        reg = <0x42e00000 0x10000>;
-                        xlnx,has-builtin-dma;
-                };
+Optional properties:
+- clock-names		: Should be  "s_axi_aclk"
+- clocks		: Input clock specifier. Refer to common clock bindings.
 
+Example:
+		axi-usb2-device@42e00000 {
+			compatible = "xlnx,usb2-device-4.00.a";
+			interrupts = <0x0 0x39 0x1>;
+			reg = <0x42e00000 0x10000>;
+			xlnx,has-builtin-dma;
+		};
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/usb/usb-hcd.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/usb/usb-hcd.yaml
@@ -33,7 +33,7 @@
   "^.*@[0-9a-f]{1,2}$":
     description: The hard wired USB devices
     type: object
-    $ref: /usb/usb-device.yaml
+    $ref: /schemas/usb/usb-device.yaml
 
 additionalProperties: true
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -782,6 +782,8 @@
     description: National Semiconductor
   "^nec,.*":
     description: NEC LCD Technologies, Ltd.
+  "^neofidelity,.*":
+    description: Neofidelity Inc.
   "^neonode,.*":
     description: Neonode Inc.
   "^netgear,.*":
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/w1/amd,axi-1wire-host.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/w1/amd,axi-1wire-host.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/w1/amd,axi-1wire-host.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: AMD AXI 1-wire bus host for programmable logic
+
+maintainers:
+  - Kris Chaplin <kris.chaplin@amd.com>
+
+properties:
+  compatible:
+    const: amd,axi-1wire-host
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    onewire@a0000000 {
+        compatible = "amd,axi-1wire-host";
+        reg = <0xa0000000 0x10000>;
+        clocks = <&zynqmp_clk 0x47>;
+        interrupts = <GIC_SPI 0x59 IRQ_TYPE_LEVEL_HIGH>;
+    };
+
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/watchdog/samsung-wdt.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/watchdog/samsung-wdt.yaml
@@ -39,8 +39,8 @@
   samsung,syscon-phandle:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
-      Phandle to the PMU system controller node (in case of Exynos5250
-      and Exynos5420).
+      Phandle to the PMU system controller node (in case of Exynos5250,
+      Exynos5420 and Exynos7).
 
 required:
   - compatible
@@ -58,6 +58,7 @@
             enum:
               - samsung,exynos5250-wdt
               - samsung,exynos5420-wdt
+              - samsung,exynos7-wdt
     then:
       required:
         - samsung,syscon-phandle
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/watchdog/xlnx,xps-timebase.yaml
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/watchdog/xlnx,xps-timebase.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/watchdog/xlnx,timebase.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx AXI/PLB softcore and window Watchdog Timer
+
+allOf:
+  - $ref: "watchdog.yaml#"
+
+maintainers:
+  - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - xlnx,xps-timebase-wdt-1.01.a
+              - xlnx,xps-timebase-wdt-1.00.a
+              - xlnx,versal-wwdt-1.0
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+
+  clock-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: |
+        Frequency of clock in Hz
+
+  xlnx,wdt-interval:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: |
+        Watchdog interval
+
+  xlnx,wdt-enable-once:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+      - enum: [0, 1]
+    description: |
+        Watchdog enable once
+
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    watchdog@40100000 {
+      clock-frequency = <50000000>;
+      compatible = "xlnx,xps-timebase-wdt-1.00.a";
+      clocks = <&clkc 15>;
+      reg = <0x40100000 0x1000>;
+      xlnx,wdt-enable-once = <0x0>;
+      xlnx,wdt-interval = <0x1b>;
+    } ;
+...
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/xlnx,ctrl-fb.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/xlnx,ctrl-fb.txt
@@ -0,0 +1,22 @@
+The Xilinx framebuffer DMA engine supports two soft IP blocks: one IP
+block is used for reading video frame data from memory (FB Read) to the device
+and the other IP block is used for writing video frame data from the device
+to memory (FB Write).  Both the FB Read/Write IP blocks are aware of the
+format of the data being written to or read from memory including RGB and
+YUV in packed, planar, and semi-planar formats.  Because the FB Read/Write
+is format aware, only one buffer pointer is needed by the IP blocks even
+when planar or semi-planar format are used.
+
+Required properties:
+ - compatible: Should be "xlnx,ctrl-fbwr-1.0" for framebuffer Write OR
+	       "xlnx,ctrl-fbrd-1.0" for framebuffer Read.
+ - reg: Base address and size of the IP core.
+ - reset-gpios: gpio to reset the framebuffer IP
+
+Example:
+
+        fbwr@0xa0000000 {
+                compatible = "xlnx,ctrl-fbwr-1.0";
+                reg = <0x0 0xa0000000 0x0 0x10000>;
+                reset-gpios = <&gpio 82 1>;
+        };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/bindings/xlnx,ctrl-vpss.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/bindings/xlnx,ctrl-vpss.txt
@@ -0,0 +1,21 @@
+The Xilinx VPSS Scaler is a Video IP that supports up scaling, down scaling and
+no scaling functionailty along with color space conversion. This supports custom
+resolution values between 0 to 4096.
+
+Required properties:
+
+- compatible: Must be "xlnx,ctrl-xvpss-1.0".
+- reg: Base address and size of the IP core.
+- reset-gpios: gpio to reset the framebuffer IP
+- xlnx,vpss-taps: number of taps
+- xlnx,vpss-ppc: pixels per clock
+
+Example:
+
+        ctrlvpss: vpss@0xa0200000 {
+                compatible = "xlnx,ctrl-xvpss-1.0";
+                reg = <0x0 0xa0200000 0x0 0x30000>;
+                reset-gpios = <&gpio 80 1>;
+                xlnx,vpss-taps = <6>;
+                xlnx,vpss-ppc = <2>;
+        };
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/configfs-overlays.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/configfs-overlays.txt
@@ -0,0 +1,31 @@
+Howto use the configfs overlay interface.
+
+A device-tree configfs entry is created in /config/device-tree/overlays
+and and it is manipulated using standard file system I/O.
+Note that this is a debug level interface, for use by developers and
+not necessarily something accessed by normal users due to the
+security implications of having direct access to the kernel's device tree.
+
+* To create an overlay you mkdir the directory:
+
+	# mkdir /config/device-tree/overlays/foo
+
+* Either you echo the overlay firmware file to the path property file.
+
+	# echo foo.dtbo >/config/device-tree/overlays/foo/path
+
+* Or you cat the contents of the overlay to the dtbo file
+
+	# cat foo.dtbo >/config/device-tree/overlays/foo/dtbo
+
+The overlay file will be applied, and devices will be created/destroyed
+as required.
+
+To remove it simply rmdir the directory.
+
+	# rmdir /config/device-tree/overlays/foo
+
+The rationalle of the dual interface (firmware & direct copy) is that each is
+better suited to different use patterns. The firmware interface is what's
+intended to be used by hardware managers in the kernel, while the copy interface
+make sense for developers (since it avoids problems with namespaces).
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/devicetree/overlay-notes.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/devicetree/overlay-notes.rst
@@ -119,10 +119,32 @@
 of_overlay_remove_all() which will remove every single one in the correct
 order.
 
-In addition, there is the option to register notifiers that get called on
+There is the option to register notifiers that get called on
 overlay operations. See of_overlay_notifier_register/unregister and
 enum of_overlay_notify_action for details.
 
-Note that a notifier callback is not supposed to store pointers to a device
-tree node or its content beyond OF_OVERLAY_POST_REMOVE corresponding to the
-respective node it received.
+A notifier callback for OF_OVERLAY_PRE_APPLY, OF_OVERLAY_POST_APPLY, or
+OF_OVERLAY_PRE_REMOVE may store pointers to a device tree node in the overlay
+or its content but these pointers must not persist past the notifier callback
+for OF_OVERLAY_POST_REMOVE.  The memory containing the overlay will be
+kfree()ed after OF_OVERLAY_POST_REMOVE notifiers are called.  Note that the
+memory will be kfree()ed even if the notifier for OF_OVERLAY_POST_REMOVE
+returns an error.
+
+The changeset notifiers in drivers/of/dynamic.c are a second type of notifier
+that could be triggered by applying or removing an overlay.  These notifiers
+are not allowed to store pointers to a device tree node in the overlay
+or its content.  The overlay code does not protect against such pointers
+remaining active when the memory containing the overlay is freed as a result
+of removing the overlay.
+
+Any other code that retains a pointer to the overlay nodes or data is
+considered to be a bug because after removing the overlay the pointer
+will refer to freed memory.
+
+Users of overlays must be especially aware of the overall operations that
+occur on the system to ensure that other kernel code does not retain any
+pointers to the overlay nodes or data.  Any example of an inadvertent use
+of such pointers is if a driver or subsystem module is loaded after an
+overlay has been applied, and the driver or subsystem scans the entire
+devicetree or a large portion of it, including the overlay nodes.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/dmaengine/dmatest.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/dmaengine/dmatest.rst
@@ -143,13 +143,14 @@
 Allocating Channels
 -------------------
 
-Channels are required to be configured prior to starting the test run.
-Attempting to run the test without configuring the channels will fail.
+Channels do not need to be configured prior to starting a test run. Attempting
+to run the test without configuring the channels will result in testing any
+channels that are available.
 
 Example::
 
     % echo 1 > /sys/module/dmatest/parameters/run
-    dmatest: Could not start test, no channels configured
+    dmatest: No channels configured, continue with any
 
 Channels are registered using the "channel" parameter. Channels can be requested by their
 name, once requested, the channel is registered and a pending thread is added to the test list.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/firewire.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/firewire.rst
@@ -19,7 +19,7 @@
 Firewire char device data structures
 ====================================
 
-.. include:: /ABI/stable/firewire-cdev
+.. include:: ../ABI/stable/firewire-cdev
     :literal:
 
 .. kernel-doc:: include/uapi/linux/firewire-cdev.h
@@ -28,7 +28,7 @@
 Firewire device probing and sysfs interfaces
 ============================================
 
-.. include:: /ABI/stable/sysfs-bus-firewire
+.. include:: ../ABI/stable/sysfs-bus-firewire
     :literal:
 
 .. kernel-doc:: drivers/firewire/core-device.c
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/firmware/other_interfaces.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/firmware/other_interfaces.rst
@@ -13,6 +13,12 @@
 .. kernel-doc:: drivers/firmware/edd.c
    :internal:
 
+Generic System Framebuffers Interface
+-------------------------------------
+
+.. kernel-doc:: drivers/firmware/sysfb.c
+   :export:
+
 Intel Stratix10 SoC Service Layer
 ---------------------------------
 Some features of the Intel Stratix10 SoC require a level of privilege
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/fpga/fpga-region.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/fpga/fpga-region.rst
@@ -46,10 +46,16 @@
 ----------------------------
 
 * struct fpga_region - The FPGA region struct
-* devm_fpga_region_create() - Allocate and init a region struct
-* fpga_region_register() -  Register an FPGA region
+* struct fpga_region_info - Parameter structure for __fpga_region_register_full()
+* __fpga_region_register_full() -  Create and register an FPGA region using the
+  fpga_region_info structure to provide the full flexibility of options
+* __fpga_region_register() -  Create and register an FPGA region using standard
+  arguments
 * fpga_region_unregister() -  Unregister an FPGA region
 
+Helper macros ``fpga_region_register()`` and ``fpga_region_register_full()``
+automatically set the module that registers the FPGA region as the owner.
+
 The FPGA region's probe function will need to get a reference to the FPGA
 Manager it will be using to do the programming.  This usually would happen
 during the region's probe function.
@@ -75,11 +81,14 @@
 .. kernel-doc:: include/linux/fpga/fpga-region.h
    :functions: fpga_region
 
+.. kernel-doc:: include/linux/fpga/fpga-region.h
+   :functions: fpga_region_info
+
 .. kernel-doc:: drivers/fpga/fpga-region.c
-   :functions: devm_fpga_region_create
+   :functions: __fpga_region_register_full
 
 .. kernel-doc:: drivers/fpga/fpga-region.c
-   :functions: fpga_region_register
+   :functions: __fpga_region_register
 
 .. kernel-doc:: drivers/fpga/fpga-region.c
    :functions: fpga_region_unregister
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/generic-counter.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/generic-counter.rst
@@ -247,7 +247,7 @@
 .. kernel-doc:: include/linux/counter.h
    :internal:
 
-.. kernel-doc:: drivers/counter/counter.c
+.. kernel-doc:: drivers/counter/counter-core.c
    :export:
 
 Implementation
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/ipmi.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/ipmi.rst
@@ -519,7 +519,7 @@
 	alerts_broken
 
 The addresses are normal I2C addresses.  The adapter is the string
-name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name.
+name of the adapter, as shown in /sys/bus/i2c/devices/i2c-<n>/name.
 It is *NOT* i2c-<n> itself.  Also, the comparison is done ignoring
 spaces, so if the name is "This is an I2C chip" you can say
 adapter_name=ThisisanI2cchip.  This is because it's hard to pass in
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/driver-api/spi.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/driver-api/spi.rst
@@ -25,8 +25,8 @@
 a pair of FIFOs connected to dual DMA engines on the other side of the
 SPI shift register (maximizing throughput). Such drivers bridge between
 whatever bus they sit on (often the platform bus) and SPI, and expose
-the SPI side of their device as a :c:type:`struct spi_master
-<spi_master>`. SPI devices are children of that master,
+the SPI side of their device as a :c:type:`struct spi_controller
+<spi_controller>`. SPI devices are children of that master,
 represented as a :c:type:`struct spi_device <spi_device>` and
 manufactured from :c:type:`struct spi_board_info
 <spi_board_info>` descriptors which are usually provided by
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/fault-injection/fault-injection.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/fault-injection/fault-injection.rst
@@ -83,9 +83,7 @@
 - /sys/kernel/debug/fail*/times:
 
 	specifies how many times failures may happen at most. A value of -1
-	means "no limit". Note, though, that this file only accepts unsigned
-	values. So, if you want to specify -1, you better use 'printf' instead
-	of 'echo', e.g.: $ printf %#x -1 > times
+	means "no limit".
 
 - /sys/kernel/debug/fail*/space:
 
@@ -277,7 +275,7 @@
     echo Y > /sys/kernel/debug/$FAILTYPE/task-filter
     echo 10 > /sys/kernel/debug/$FAILTYPE/probability
     echo 100 > /sys/kernel/debug/$FAILTYPE/interval
-    printf %#x -1 > /sys/kernel/debug/$FAILTYPE/times
+    echo -1 > /sys/kernel/debug/$FAILTYPE/times
     echo 0 > /sys/kernel/debug/$FAILTYPE/space
     echo 2 > /sys/kernel/debug/$FAILTYPE/verbose
     echo 1 > /sys/kernel/debug/$FAILTYPE/ignore-gfp-wait
@@ -331,7 +329,7 @@
     echo N > /sys/kernel/debug/$FAILTYPE/task-filter
     echo 10 > /sys/kernel/debug/$FAILTYPE/probability
     echo 100 > /sys/kernel/debug/$FAILTYPE/interval
-    printf %#x -1 > /sys/kernel/debug/$FAILTYPE/times
+    echo -1 > /sys/kernel/debug/$FAILTYPE/times
     echo 0 > /sys/kernel/debug/$FAILTYPE/space
     echo 2 > /sys/kernel/debug/$FAILTYPE/verbose
     echo 1 > /sys/kernel/debug/$FAILTYPE/ignore-gfp-wait
@@ -362,7 +360,7 @@
     echo N > /sys/kernel/debug/$FAILTYPE/task-filter
     echo 100 > /sys/kernel/debug/$FAILTYPE/probability
     echo 0 > /sys/kernel/debug/$FAILTYPE/interval
-    printf %#x -1 > /sys/kernel/debug/$FAILTYPE/times
+    echo -1 > /sys/kernel/debug/$FAILTYPE/times
     echo 0 > /sys/kernel/debug/$FAILTYPE/space
     echo 1 > /sys/kernel/debug/$FAILTYPE/verbose
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/README
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/README
@@ -0,0 +1,396 @@
+
+Aufs5 -- advanced multi layered unification filesystem version 5.x
+http://aufs.sf.net
+Junjiro R. Okajima
+
+
+0. Introduction
+----------------------------------------
+In the early days, aufs was entirely re-designed and re-implemented
+Unionfs Version 1.x series. Adding many original ideas, approaches,
+improvements and implementations, it became totally different from
+Unionfs while keeping the basic features.
+Later, Unionfs Version 2.x series began taking some of the same
+approaches to aufs1's.
+Unionfs was being developed by Professor Erez Zadok at Stony Brook
+University and his team.
+
+Aufs5 supports linux-v5.0 and later, If you want older kernel version
+support,
+- for linux-v4.x series, try aufs4-linux.git or aufs4-standalone.git
+- for linux-v3.x series, try aufs3-linux.git or aufs3-standalone.git
+- for linux-v2.6.16 and later, try aufs2-2.6.git, aufs2-standalone.git
+  or aufs1 from CVS on SourceForge.
+
+Note: it becomes clear that "Aufs was rejected. Let's give it up."
+      According to Christoph Hellwig, linux rejects all union-type
+      filesystems but UnionMount.
+<http://marc.info/?l=linux-kernel&m=123938533724484&w=2>
+
+PS. Al Viro seems have a plan to merge aufs as well as overlayfs and
+    UnionMount, and he pointed out an issue around a directory mutex
+    lock and aufs addressed it. But it is still unsure whether aufs will
+    be merged (or any other union solution).
+<http://marc.info/?l=linux-kernel&m=136312705029295&w=1>
+
+
+1. Features
+----------------------------------------
+- unite several directories into a single virtual filesystem. The member
+  directory is called as a branch.
+- you can specify the permission flags to the branch, which are 'readonly',
+  'readwrite' and 'whiteout-able.'
+- by upper writable branch, internal copyup and whiteout, files/dirs on
+  readonly branch are modifiable logically.
+- dynamic branch manipulation, add, del.
+- etc...
+
+Also there are many enhancements in aufs, such as:
+- test only the highest one for the directory permission (dirperm1)
+- copyup on open (coo=)
+- 'move' policy for copy-up between two writable branches, after
+  checking free space.
+- xattr, acl
+- readdir(3) in userspace.
+- keep inode number by external inode number table
+- keep the timestamps of file/dir in internal copyup operation
+- seekable directory, supporting NFS readdir.
+- whiteout is hardlinked in order to reduce the consumption of inodes
+  on branch
+- do not copyup, nor create a whiteout when it is unnecessary
+- revert a single systemcall when an error occurs in aufs
+- remount interface instead of ioctl
+- maintain /etc/mtab by an external command, /sbin/mount.aufs.
+- loopback mounted filesystem as a branch
+- kernel thread for removing the dir who has a plenty of whiteouts
+- support copyup sparse file (a file which has a 'hole' in it)
+- default permission flags for branches
+- selectable permission flags for ro branch, whether whiteout can
+  exist or not
+- export via NFS.
+- support <sysfs>/fs/aufs and <debugfs>/aufs.
+- support multiple writable branches, some policies to select one
+  among multiple writable branches.
+- a new semantics for link(2) and rename(2) to support multiple
+  writable branches.
+- no glibc changes are required.
+- pseudo hardlink (hardlink over branches)
+- allow a direct access manually to a file on branch, e.g. bypassing aufs.
+  including NFS or remote filesystem branch.
+- userspace wrapper for pathconf(3)/fpathconf(3) with _PC_LINK_MAX.
+- and more...
+
+Currently these features are dropped temporary from aufs5.
+See design/08plan.txt in detail.
+- nested mount, i.e. aufs as readonly no-whiteout branch of another aufs
+  (robr)
+- statistics of aufs thread (/sys/fs/aufs/stat)
+
+Features or just an idea in the future (see also design/*.txt),
+- reorder the branch index without del/re-add.
+- permanent xino files for NFSD
+- an option for refreshing the opened files after add/del branches
+- light version, without branch manipulation. (unnecessary?)
+- copyup in userspace
+- inotify in userspace
+- readv/writev
+
+
+2. Download
+----------------------------------------
+There are three GIT trees for aufs5, aufs5-linux.git,
+aufs5-standalone.git, and aufs-util.git. Note that there is no "5" in
+"aufs-util.git."
+While the aufs-util is always necessary, you need either of aufs5-linux
+or aufs5-standalone.
+
+The aufs5-linux tree includes the whole linux mainline GIT tree,
+git://git.kernel.org/.../torvalds/linux.git.
+And you cannot select CONFIG_AUFS_FS=m for this version, eg. you cannot
+build aufs5 as an external kernel module.
+Several extra patches are not included in this tree. Only
+aufs5-standalone tree contains them. They are described in the later
+section "Configuration and Compilation."
+
+On the other hand, the aufs5-standalone tree has only aufs source files
+and necessary patches, and you can select CONFIG_AUFS_FS=m.
+But you need to apply all aufs patches manually.
+
+You will find GIT branches whose name is in form of "aufs5.x" where "x"
+represents the linux kernel version, "linux-5.x". For instance,
+"aufs5.0" is for linux-5.0. For latest "linux-5.x-rcN", use
+"aufs5.x-rcN" branch.
+
+o aufs5-linux tree
+$ git clone --reference /your/linux/git/tree \
+	git://github.com/sfjro/aufs5-linux.git aufs5-linux.git
+- if you don't have linux GIT tree, then remove "--reference ..."
+$ cd aufs5-linux.git
+$ git checkout origin/aufs5.0
+
+Or You may want to directly git-pull aufs into your linux GIT tree, and
+leave the patch-work to GIT.
+$ cd /your/linux/git/tree
+$ git remote add aufs5 git://github.com/sfjro/aufs5-linux.git
+$ git fetch aufs5
+$ git checkout -b my5.0 v5.0
+$ (add your local change...)
+$ git pull aufs5 aufs5.0
+- now you have v5.0 + your_changes + aufs5.0 in you my5.0 branch.
+- you may need to solve some conflicts between your_changes and
+  aufs5.0. in this case, git-rerere is recommended so that you can
+  solve the similar conflicts automatically when you upgrade to 5.1 or
+  later in the future.
+
+o aufs5-standalone tree
+$ git clone git://github.com/sfjro/aufs5-standalone.git aufs5-standalone.git
+$ cd aufs5-standalone.git
+$ git checkout origin/aufs5.0
+
+o aufs-util tree
+$ git clone git://git.code.sf.net/p/aufs/aufs-util aufs-util.git
+- note that the public aufs-util.git is on SourceForge instead of
+  GitHUB.
+$ cd aufs-util.git
+$ git checkout origin/aufs5.0
+
+Note: The 5.x-rcN branch is to be used with `rc' kernel versions ONLY.
+The minor version number, 'x' in '5.x', of aufs may not always
+follow the minor version number of the kernel.
+Because changes in the kernel that cause the use of a new
+minor version number do not always require changes to aufs-util.
+
+Since aufs-util has its own minor version number, you may not be
+able to find a GIT branch in aufs-util for your kernel's
+exact minor version number.
+In this case, you should git-checkout the branch for the
+nearest lower number.
+
+For (an unreleased) example:
+If you are using "linux-5.10" and the "aufs5.10" branch
+does not exist in aufs-util repository, then "aufs5.9", "aufs5.8"
+or something numerically smaller is the branch for your kernel.
+
+Also you can view all branches by
+	$ git branch -a
+
+
+3. Configuration and Compilation
+----------------------------------------
+Make sure you have git-checkout'ed the correct branch.
+
+For aufs5-linux tree,
+- enable CONFIG_AUFS_FS.
+- set other aufs configurations if necessary.
+- for aufs5.13 and later
+  Because aufs is not only an ordinary filesystem (callee of VFS), but
+  also a caller of VFS functions for branch filesystems, subclassing of
+  the internal locks for LOCKDEP is necessary. LOCKDEP is a debugging
+  feature of linux kernel. If you enable CONFIG_LOCKDEP, then you will
+  need to customize some LOCKDEP numbers. Here are what I use on my
+  test environment.
+	CONFIG_LOCKDEP_BITS=21
+	CONFIG_LOCKDEP_CHAINS_BITS=21
+	CONFIG_LOCKDEP_STACK_TRACE_BITS=24
+
+For aufs5-standalone tree,
+There are several ways to build.
+
+1.
+- apply ./aufs5-kbuild.patch to your kernel source files.
+- apply ./aufs5-base.patch too.
+- apply ./aufs5-mmap.patch too.
+- apply ./aufs5-standalone.patch too, if you have a plan to set
+  CONFIG_AUFS_FS=m. otherwise you don't need ./aufs5-standalone.patch.
+- copy ./{Documentation,fs,include/uapi/linux/aufs_type.h} files to your
+  kernel source tree. Never copy $PWD/include/uapi/linux/Kbuild.
+- enable CONFIG_AUFS_FS, you can select either
+  =m or =y.
+- and build your kernel as usual.
+- install the built kernel.
+- install the header files too by "make headers_install" to the
+  directory where you specify. By default, it is $PWD/usr.
+  "make help" shows a brief note for headers_install.
+- and reboot your system.
+
+2.
+- module only (CONFIG_AUFS_FS=m).
+- apply ./aufs5-base.patch to your kernel source files.
+- apply ./aufs5-mmap.patch too.
+- apply ./aufs5-standalone.patch too.
+- build your kernel, don't forget "make headers_install", and reboot.
+- edit ./config.mk and set other aufs configurations if necessary.
+  Note: You should read $PWD/fs/aufs/Kconfig carefully which describes
+  every aufs configurations.
+- build the module by simple "make".
+- you can specify ${KDIR} make variable which points to your kernel
+  source tree.
+- install the files
+  + run "make install" to install the aufs module, or copy the built
+    $PWD/aufs.ko to /lib/modules/... and run depmod -a (or reboot simply).
+  + run "make install_headers" (instead of headers_install) to install
+    the modified aufs header file (you can specify DESTDIR which is
+    available in aufs standalone version's Makefile only), or copy
+    $PWD/usr/include/linux/aufs_type.h to /usr/include/linux or wherever
+    you like manually. By default, the target directory is $PWD/usr.
+- no need to apply aufs5-kbuild.patch, nor copying source files to your
+  kernel source tree.
+
+Note: The header file aufs_type.h is necessary to build aufs-util
+      as well as "make headers_install" in the kernel source tree.
+      headers_install is subject to be forgotten, but it is essentially
+      necessary, not only for building aufs-util.
+      You may not meet problems without headers_install in some older
+      version though.
+
+And then,
+- read README in aufs-util, build and install it
+- note that your distribution may contain an obsoleted version of
+  aufs_type.h in /usr/include/linux or something. When you build aufs
+  utilities, make sure that your compiler refers the correct aufs header
+  file which is built by "make headers_install."
+- if you want to use readdir(3) in userspace or pathconf(3) wrapper,
+  then run "make install_ulib" too. And refer to the aufs manual in
+  detail.
+
+There several other patches in aufs5-standalone.git. They are all
+optional. When you meet some problems, they will help you.
+- aufs5-loopback.patch
+  Supports a nested loopback mount in a branch-fs. This patch is
+  unnecessary until aufs produces a message like "you may want to try
+  another patch for loopback file".
+- vfs-ino.patch
+  Modifies a system global kernel internal function get_next_ino() in
+  order to stop assigning 0 for an inode-number. Not directly related to
+  aufs, but recommended generally.
+- tmpfs-idr.patch
+  Keeps the tmpfs inode number as the lowest value. Effective to reduce
+  the size of aufs XINO files for tmpfs branch. Also it prevents the
+  duplication of inode number, which is important for backup tools and
+  other utilities. When you find aufs XINO files for tmpfs branch
+  growing too much, try this patch.
+
+
+4. Usage
+----------------------------------------
+At first, make sure aufs-util are installed, and please read the aufs
+manual, aufs.5 in aufs-util.git tree.
+$ man -l aufs.5
+
+And then,
+$ mkdir /tmp/rw /tmp/aufs
+# mount -t aufs -o br=/tmp/rw:${HOME} none /tmp/aufs
+
+Here is another example. The result is equivalent.
+# mount -t aufs -o br=/tmp/rw=rw:${HOME}=ro none /tmp/aufs
+  Or
+# mount -t aufs -o br:/tmp/rw none /tmp/aufs
+# mount -o remount,append:${HOME} /tmp/aufs
+
+Then, you can see whole tree of your home dir through /tmp/aufs. If
+you modify a file under /tmp/aufs, the one on your home directory is
+not affected, instead the same named file will be newly created under
+/tmp/rw. And all of your modification to a file will be applied to
+the one under /tmp/rw. This is called the file based Copy on Write
+(COW) method.
+Aufs mount options are described in aufs.5.
+If you run chroot or something and make your aufs as a root directory,
+then you need to customize the shutdown script. See the aufs manual in
+detail.
+
+Additionally, there are some sample usages of aufs which are a
+diskless system with network booting, and LiveCD over NFS.
+See sample dir in CVS tree on SourceForge.
+
+
+5. Contact
+----------------------------------------
+When you have any problems or strange behaviour in aufs, please let me
+know with:
+- /proc/mounts (instead of the output of mount(8))
+- /sys/module/aufs/*
+- /sys/fs/aufs/* (if you have them)
+- /debug/aufs/* (if you have them)
+- linux kernel version
+  if your kernel is not plain, for example modified by distributor,
+  the url where i can download its source is necessary too.
+- aufs version which was printed at loading the module or booting the
+  system, instead of the date you downloaded.
+- configuration (define/undefine CONFIG_AUFS_xxx)
+- kernel configuration or /proc/config.gz (if you have it)
+- LSM (linux security module, if you are using)
+- behaviour which you think to be incorrect
+- actual operation, reproducible one is better
+- mailto: aufs-users at lists.sourceforge.net
+
+Usually, I don't watch the Public Areas(Bugs, Support Requests, Patches,
+and Feature Requests) on SourceForge. Please join and write to
+aufs-users ML.
+
+
+6. Acknowledgements
+----------------------------------------
+Thanks to everyone who have tried and are using aufs, whoever
+have reported a bug or any feedback.
+
+Especially donators:
+Tomas Matejicek(slax.org) made a donation (much more than once).
+	Since Apr 2010, Tomas M (the author of Slax and Linux Live
+	scripts) is making "doubling" donations.
+	Unfortunately I cannot list all of the donators, but I really
+	appreciate.
+	It ends Aug 2010, but the ordinary donation URL is still available.
+	<http://sourceforge.net/donate/index.php?group_id=167503>
+Dai Itasaka made a donation (2007/8).
+Chuck Smith made a donation (2008/4, 10 and 12).
+Henk Schoneveld made a donation (2008/9).
+Chih-Wei Huang, ASUS, CTC donated Eee PC 4G (2008/10).
+Francois Dupoux made a donation (2008/11).
+Bruno Cesar Ribas and Luis Carlos Erpen de Bona, C3SL serves public
+	aufs2 GIT tree (2009/2).
+William Grant made a donation (2009/3).
+Patrick Lane made a donation (2009/4).
+The Mail Archive (mail-archive.com) made donations (2009/5).
+Nippy Networks (Ed Wildgoose) made a donation (2009/7).
+New Dream Network, LLC (www.dreamhost.com) made a donation (2009/11).
+Pavel Pronskiy made a donation (2011/2).
+Iridium and Inmarsat satellite phone retailer (www.mailasail.com), Nippy
+	Networks (Ed Wildgoose) made a donation for hardware (2011/3).
+Max Lekomcev (DOM-TV project) made a donation (2011/7, 12, 2012/3, 6 and
+11).
+Sam Liddicott made a donation (2011/9).
+Era Scarecrow made a donation (2013/4).
+Bor Ratajc made a donation (2013/4).
+Alessandro Gorreta made a donation (2013/4).
+POIRETTE Marc made a donation (2013/4).
+Alessandro Gorreta made a donation (2013/4).
+lauri kasvandik made a donation (2013/5).
+"pemasu from Finland" made a donation (2013/7).
+The Parted Magic Project made a donation (2013/9 and 11).
+Pavel Barta made a donation (2013/10).
+Nikolay Pertsev made a donation (2014/5).
+James B made a donation (2014/7 and 2015/7).
+Stefano Di Biase made a donation (2014/8).
+Daniel Epellei made a donation (2015/1).
+OmegaPhil made a donation (2016/1, 2018/4).
+Tomasz Szewczyk made a donation (2016/4).
+James Burry made a donation (2016/12).
+Carsten Rose made a donation (2018/9).
+Porteus Kiosk made a donation (2018/10).
+
+Thank you very much.
+Donations are always, including future donations, very important and
+helpful for me to keep on developing aufs.
+
+
+7.
+----------------------------------------
+If you are an experienced user, no explanation is needed. Aufs is
+just a linux filesystem.
+
+
+Enjoy!
+
+# Local variables: ;
+# mode: text;
+# End: ;
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/01intro.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/01intro.txt
@@ -0,0 +1,171 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Introduction
+----------------------------------------
+
+aufs [ei ju: ef es] | /ey-yoo-ef-es/ | [a u f s]
+1. abbrev. for "advanced multi-layered unification filesystem".
+2. abbrev. for "another unionfs".
+3. abbrev. for "auf das" in German which means "on the" in English.
+   Ex. "Butter aufs Brot"(G) means "butter onto bread"(E).
+   But "Filesystem aufs Filesystem" is hard to understand.
+4. abbrev. for "African Urban Fashion Show".
+
+AUFS is a filesystem with features:
+- multi layered stackable unification filesystem, the member directory
+  is called as a branch.
+- branch permission and attribute, 'readonly', 'real-readonly',
+  'readwrite', 'whiteout-able', 'link-able whiteout', etc. and their
+  combination.
+- internal "file copy-on-write".
+- logical deletion, whiteout.
+- dynamic branch manipulation, adding, deleting and changing permission.
+- allow bypassing aufs, user's direct branch access.
+- external inode number translation table and bitmap which maintains the
+  persistent aufs inode number.
+- seekable directory, including NFS readdir.
+- file mapping, mmap and sharing pages.
+- pseudo-link, hardlink over branches.
+- loopback mounted filesystem as a branch.
+- several policies to select one among multiple writable branches.
+- revert a single systemcall when an error occurs in aufs.
+- and more...
+
+
+Multi Layered Stackable Unification Filesystem
+----------------------------------------------------------------------
+Most people already knows what it is.
+It is a filesystem which unifies several directories and provides a
+merged single directory. When users access a file, the access will be
+passed/re-directed/converted (sorry, I am not sure which English word is
+correct) to the real file on the member filesystem. The member
+filesystem is called 'lower filesystem' or 'branch' and has a mode
+'readonly' and 'readwrite.' And the deletion for a file on the lower
+readonly branch is handled by creating 'whiteout' on the upper writable
+branch.
+
+On LKML, there have been discussions about UnionMount (Jan Blunck,
+Bharata B Rao and Valerie Aurora) and Unionfs (Erez Zadok). They took
+different approaches to implement the merged-view.
+The former tries putting it into VFS, and the latter implements as a
+separate filesystem.
+(If I misunderstand about these implementations, please let me know and
+I shall correct it. Because it is a long time ago when I read their
+source files last time).
+
+UnionMount's approach will be able to small, but may be hard to share
+branches between several UnionMount since the whiteout in it is
+implemented in the inode on branch filesystem and always
+shared. According to Bharata's post, readdir does not seems to be
+finished yet.
+There are several missing features known in this implementations such as
+- for users, the inode number may change silently. eg. copy-up.
+- link(2) may break by copy-up.
+- read(2) may get an obsoleted filedata (fstat(2) too).
+- fcntl(F_SETLK) may be broken by copy-up.
+- unnecessary copy-up may happen, for example mmap(MAP_PRIVATE) after
+  open(O_RDWR).
+
+In linux-3.18, "overlay" filesystem (formerly known as "overlayfs") was
+merged into mainline. This is another implementation of UnionMount as a
+separated filesystem. All the limitations and known problems which
+UnionMount are equally inherited to "overlay" filesystem.
+
+Unionfs has a longer history. When I started implementing a stackable
+filesystem (Aug 2005), it already existed. It has virtual super_block,
+inode, dentry and file objects and they have an array pointing lower
+same kind objects. After contributing many patches for Unionfs, I
+re-started my project AUFS (Jun 2006).
+
+In AUFS, the structure of filesystem resembles to Unionfs, but I
+implemented my own ideas, approaches and enhancements and it became
+totally different one.
+
+Comparing DM snapshot and fs based implementation
+- the number of bytes to be copied between devices is much smaller.
+- the type of filesystem must be one and only.
+- the fs must be writable, no readonly fs, even for the lower original
+  device. so the compression fs will not be usable. but if we use
+  loopback mount, we may address this issue.
+  for instance,
+	mount /cdrom/squashfs.img /sq
+	losetup /sq/ext2.img
+	losetup /somewhere/cow
+	dmsetup "snapshot /dev/loop0 /dev/loop1 ..."
+- it will be difficult (or needs more operations) to extract the
+  difference between the original device and COW.
+- DM snapshot-merge may help a lot when users try merging. in the
+  fs-layer union, users will use rsync(1).
+
+You may want to read my old paper "Filesystems in LiveCD"
+(http://aufs.sourceforge.net/aufs2/report/sq/sq.pdf).
+
+
+Several characters/aspects/persona of aufs
+----------------------------------------------------------------------
+
+Aufs has several characters, aspects or persona.
+1. a filesystem, callee of VFS helper
+2. sub-VFS, caller of VFS helper for branches
+3. a virtual filesystem which maintains persistent inode number
+4. reader/writer of files on branches such like an application
+
+1. Callee of VFS Helper
+As an ordinary linux filesystem, aufs is a callee of VFS. For instance,
+unlink(2) from an application reaches sys_unlink() kernel function and
+then vfs_unlink() is called. vfs_unlink() is one of VFS helper and it
+calls filesystem specific unlink operation. Actually aufs implements the
+unlink operation but it behaves like a redirector.
+
+2. Caller of VFS Helper for Branches
+aufs_unlink() passes the unlink request to the branch filesystem as if
+it were called from VFS. So the called unlink operation of the branch
+filesystem acts as usual. As a caller of VFS helper, aufs should handle
+every necessary pre/post operation for the branch filesystem.
+- acquire the lock for the parent dir on a branch
+- lookup in a branch
+- revalidate dentry on a branch
+- mnt_want_write() for a branch
+- vfs_unlink() for a branch
+- mnt_drop_write() for a branch
+- release the lock on a branch
+
+3. Persistent Inode Number
+One of the most important issue for a filesystem is to maintain inode
+numbers. This is particularly important to support exporting a
+filesystem via NFS. Aufs is a virtual filesystem which doesn't have a
+backend block device for its own. But some storage is necessary to
+keep and maintain the inode numbers. It may be a large space and may not
+suit to keep in memory. Aufs rents some space from its first writable
+branch filesystem (by default) and creates file(s) on it. These files
+are created by aufs internally and removed soon (currently) keeping
+opened.
+Note: Because these files are removed, they are totally gone after
+      unmounting aufs. It means the inode numbers are not persistent
+      across unmount or reboot. I have a plan to make them really
+      persistent which will be important for aufs on NFS server.
+
+4. Read/Write Files Internally (copy-on-write)
+Because a branch can be readonly, when you write a file on it, aufs will
+"copy-up" it to the upper writable branch internally. And then write the
+originally requested thing to the file. Generally kernel doesn't
+open/read/write file actively. In aufs, even a single write may cause a
+internal "file copy". This behaviour is very similar to cp(1) command.
+
+Some people may think it is better to pass such work to user space
+helper, instead of doing in kernel space. Actually I am still thinking
+about it. But currently I have implemented it in kernel space.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/02struct.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/02struct.txt
@@ -0,0 +1,258 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Basic Aufs Internal Structure
+
+Superblock/Inode/Dentry/File Objects
+----------------------------------------------------------------------
+As like an ordinary filesystem, aufs has its own
+superblock/inode/dentry/file objects. All these objects have a
+dynamically allocated array and store the same kind of pointers to the
+lower filesystem, branch.
+For example, when you build a union with one readwrite branch and one
+readonly, mounted /au, /rw and /ro respectively.
+- /au = /rw + /ro
+- /ro/fileA exists but /rw/fileA
+
+Aufs lookup operation finds /ro/fileA and gets dentry for that. These
+pointers are stored in a aufs dentry. The array in aufs dentry will be,
+- [0] = NULL (because /rw/fileA doesn't exist)
+- [1] = /ro/fileA
+
+This style of an array is essentially same to the aufs
+superblock/inode/dentry/file objects.
+
+Because aufs supports manipulating branches, ie. add/delete/change
+branches dynamically, these objects has its own generation. When
+branches are changed, the generation in aufs superblock is
+incremented. And a generation in other object are compared when it is
+accessed. When a generation in other objects are obsoleted, aufs
+refreshes the internal array.
+
+
+Superblock
+----------------------------------------------------------------------
+Additionally aufs superblock has some data for policies to select one
+among multiple writable branches, XIB files, pseudo-links and kobject.
+See below in detail.
+About the policies which supports copy-down a directory, see
+wbr_policy.txt too.
+
+
+Branch and XINO(External Inode Number Translation Table)
+----------------------------------------------------------------------
+Every branch has its own xino (external inode number translation table)
+file. The xino file is created and unlinked by aufs internally. When two
+members of a union exist on the same filesystem, they share the single
+xino file.
+The struct of a xino file is simple, just a sequence of aufs inode
+numbers which is indexed by the lower inode number.
+In the above sample, assume the inode number of /ro/fileA is i111 and
+aufs assigns the inode number i999 for fileA. Then aufs writes 999 as
+4(8) bytes at 111 * 4(8) bytes offset in the xino file.
+
+When the inode numbers are not contiguous, the xino file will be sparse
+which has a hole in it and doesn't consume as much disk space as it
+might appear. If your branch filesystem consumes disk space for such
+holes, then you should specify 'xino=' option at mounting aufs.
+
+Aufs has a mount option to free the disk blocks for such holes in XINO
+files on tmpfs or ramdisk. But it is not so effective actually. If you
+meet a problem of disk shortage due to XINO files, then you should try
+"tmpfs-ino.patch" (and "vfs-ino.patch" too) in aufs4-standalone.git.
+The patch localizes the assignment inumbers per tmpfs-mount and avoid
+the holes in XINO files.
+
+Also a writable branch has three kinds of "whiteout bases". All these
+are existed when the branch is joined to aufs, and their names are
+whiteout-ed doubly, so that users will never see their names in aufs
+hierarchy.
+1. a regular file which will be hardlinked to all whiteouts.
+2. a directory to store a pseudo-link.
+3. a directory to store an "orphan"-ed file temporary.
+
+1. Whiteout Base
+   When you remove a file on a readonly branch, aufs handles it as a
+   logical deletion and creates a whiteout on the upper writable branch
+   as a hardlink of this file in order not to consume inode on the
+   writable branch.
+2. Pseudo-link Dir
+   See below, Pseudo-link.
+3. Step-Parent Dir
+   When "fileC" exists on the lower readonly branch only and it is
+   opened and removed with its parent dir, and then user writes
+   something into it, then aufs copies-up fileC to this
+   directory. Because there is no other dir to store fileC. After
+   creating a file under this dir, the file is unlinked.
+
+Because aufs supports manipulating branches, ie. add/delete/change
+dynamically, a branch has its own id. When the branch order changes,
+aufs finds the new index by searching the branch id.
+
+
+Pseudo-link
+----------------------------------------------------------------------
+Assume "fileA" exists on the lower readonly branch only and it is
+hardlinked to "fileB" on the branch. When you write something to fileA,
+aufs copies-up it to the upper writable branch. Additionally aufs
+creates a hardlink under the Pseudo-link Directory of the writable
+branch. The inode of a pseudo-link is kept in aufs super_block as a
+simple list. If fileB is read after unlinking fileA, aufs returns
+filedata from the pseudo-link instead of the lower readonly
+branch. Because the pseudo-link is based upon the inode, to keep the
+inode number by xino (see above) is essentially necessary.
+
+All the hardlinks under the Pseudo-link Directory of the writable branch
+should be restored in a proper location later. Aufs provides a utility
+to do this. The userspace helpers executed at remounting and unmounting
+aufs by default.
+During this utility is running, it puts aufs into the pseudo-link
+maintenance mode. In this mode, only the process which began the
+maintenance mode (and its child processes) is allowed to operate in
+aufs. Some other processes which are not related to the pseudo-link will
+be allowed to run too, but the rest have to return an error or wait
+until the maintenance mode ends. If a process already acquires an inode
+mutex (in VFS), it has to return an error.
+
+
+XIB(external inode number bitmap)
+----------------------------------------------------------------------
+Addition to the xino file per a branch, aufs has an external inode number
+bitmap in a superblock object. It is also an internal file such like a
+xino file.
+It is a simple bitmap to mark whether the aufs inode number is in-use or
+not.
+To reduce the file I/O, aufs prepares a single memory page to cache xib.
+
+As well as XINO files, aufs has a feature to truncate/refresh XIB to
+reduce the number of consumed disk blocks for these files.
+
+
+Virtual or Vertical Dir, and Readdir in Userspace
+----------------------------------------------------------------------
+In order to support multiple layers (branches), aufs readdir operation
+constructs a virtual dir block on memory. For readdir, aufs calls
+vfs_readdir() internally for each dir on branches, merges their entries
+with eliminating the whiteout-ed ones, and sets it to file (dir)
+object. So the file object has its entry list until it is closed. The
+entry list will be updated when the file position is zero and becomes
+obsoleted. This decision is made in aufs automatically.
+
+The dynamically allocated memory block for the name of entries has a
+unit of 512 bytes (by default) and stores the names contiguously (no
+padding). Another block for each entry is handled by kmem_cache too.
+During building dir blocks, aufs creates hash list and judging whether
+the entry is whiteouted by its upper branch or already listed.
+The merged result is cached in the corresponding inode object and
+maintained by a customizable life-time option.
+
+Some people may call it can be a security hole or invite DoS attack
+since the opened and once readdir-ed dir (file object) holds its entry
+list and becomes a pressure for system memory. But I'd say it is similar
+to files under /proc or /sys. The virtual files in them also holds a
+memory page (generally) while they are opened. When an idea to reduce
+memory for them is introduced, it will be applied to aufs too.
+For those who really hate this situation, I've developed readdir(3)
+library which operates this merging in userspace. You just need to set
+LD_PRELOAD environment variable, and aufs will not consume no memory in
+kernel space for readdir(3).
+
+
+Workqueue
+----------------------------------------------------------------------
+Aufs sometimes requires privilege access to a branch. For instance,
+in copy-up/down operation. When a user process is going to make changes
+to a file which exists in the lower readonly branch only, and the mode
+of one of ancestor directories may not be writable by a user
+process. Here aufs copy-up the file with its ancestors and they may
+require privilege to set its owner/group/mode/etc.
+This is a typical case of a application character of aufs (see
+Introduction).
+
+Aufs uses workqueue synchronously for this case. It creates its own
+workqueue. The workqueue is a kernel thread and has privilege. Aufs
+passes the request to call mkdir or write (for example), and wait for
+its completion. This approach solves a problem of a signal handler
+simply.
+If aufs didn't adopt the workqueue and changed the privilege of the
+process, then the process may receive the unexpected SIGXFSZ or other
+signals.
+
+Also aufs uses the system global workqueue ("events" kernel thread) too
+for asynchronous tasks, such like handling inotify/fsnotify, re-creating a
+whiteout base and etc. This is unrelated to a privilege.
+Most of aufs operation tries acquiring a rw_semaphore for aufs
+superblock at the beginning, at the same time waits for the completion
+of all queued asynchronous tasks.
+
+
+Whiteout
+----------------------------------------------------------------------
+The whiteout in aufs is very similar to Unionfs's. That is represented
+by its filename. UnionMount takes an approach of a file mode, but I am
+afraid several utilities (find(1) or something) will have to support it.
+
+Basically the whiteout represents "logical deletion" which stops aufs to
+lookup further, but also it represents "dir is opaque" which also stop
+further lookup.
+
+In aufs, rmdir(2) and rename(2) for dir uses whiteout alternatively.
+In order to make several functions in a single systemcall to be
+revertible, aufs adopts an approach to rename a directory to a temporary
+unique whiteouted name.
+For example, in rename(2) dir where the target dir already existed, aufs
+renames the target dir to a temporary unique whiteouted name before the
+actual rename on a branch, and then handles other actions (make it opaque,
+update the attributes, etc). If an error happens in these actions, aufs
+simply renames the whiteouted name back and returns an error. If all are
+succeeded, aufs registers a function to remove the whiteouted unique
+temporary name completely and asynchronously to the system global
+workqueue.
+
+
+Copy-up
+----------------------------------------------------------------------
+It is a well-known feature or concept.
+When user modifies a file on a readonly branch, aufs operate "copy-up"
+internally and makes change to the new file on the upper writable branch.
+When the trigger systemcall does not update the timestamps of the parent
+dir, aufs reverts it after copy-up.
+
+
+Move-down (aufs3.9 and later)
+----------------------------------------------------------------------
+"Copy-up" is one of the essential feature in aufs. It copies a file from
+the lower readonly branch to the upper writable branch when a user
+changes something about the file.
+"Move-down" is an opposite action of copy-up. Basically this action is
+ran manually instead of automatically and internally.
+For desgin and implementation, aufs has to consider these issues.
+- whiteout for the file may exist on the lower branch.
+- ancestor directories may not exist on the lower branch.
+- diropq for the ancestor directories may exist on the upper branch.
+- free space on the lower branch will reduce.
+- another access to the file may happen during moving-down, including
+  UDBA (see "Revalidate Dentry and UDBA").
+- the file should not be hard-linked nor pseudo-linked. they should be
+  handled by auplink utility later.
+
+Sometimes users want to move-down a file from the upper writable branch
+to the lower readonly or writable branch. For instance,
+- the free space of the upper writable branch is going to run out.
+- create a new intermediate branch between the upper and lower branch.
+- etc.
+
+For this purpose, use "aumvdown" command in aufs-util.git.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/03atomic_open.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/03atomic_open.txt
@@ -0,0 +1,85 @@
+
+# Copyright (C) 2015-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Support for a branch who has its ->atomic_open()
+----------------------------------------------------------------------
+The filesystems who implement its ->atomic_open() are not majority. For
+example NFSv4 does, and aufs should call NFSv4 ->atomic_open,
+particularly for open(O_CREAT|O_EXCL, 0400) case. Other than
+->atomic_open(), NFSv4 returns an error for this open(2). While I am not
+sure whether all filesystems who have ->atomic_open() behave like this,
+but NFSv4 surely returns the error.
+
+In order to support ->atomic_open() for aufs, there are a few
+approaches.
+
+A. Introduce aufs_atomic_open()
+   - calls one of VFS:do_last(), lookup_open() or atomic_open() for
+     branch fs.
+B. Introduce aufs_atomic_open() calling create, open and chmod. this is
+   an aufs user Pip Cet's approach
+   - calls aufs_create(), VFS finish_open() and notify_change().
+   - pass fake-mode to finish_open(), and then correct the mode by
+     notify_change().
+C. Extend aufs_open() to call branch fs's ->atomic_open()
+   - no aufs_atomic_open().
+   - aufs_lookup() registers the TID to an aufs internal object.
+   - aufs_create() does nothing when the matching TID is registered, but
+     registers the mode.
+   - aufs_open() calls branch fs's ->atomic_open() when the matching
+     TID is registered.
+D. Extend aufs_open() to re-try branch fs's ->open() with superuser's
+   credential
+   - no aufs_atomic_open().
+   - aufs_create() registers the TID to an internal object. this info
+     represents "this process created this file just now."
+   - when aufs gets EACCES from branch fs's ->open(), then confirm the
+     registered TID and re-try open() with superuser's credential.
+
+Pros and cons for each approach.
+
+A.
+   - straightforward but highly depends upon VFS internal.
+   - the atomic behavaiour is kept.
+   - some of parameters such as nameidata are hard to reproduce for
+     branch fs.
+   - large overhead.
+B.
+   - easy to implement.
+   - the atomic behavaiour is lost.
+C.
+   - the atomic behavaiour is kept.
+   - dirty and tricky.
+   - VFS checks whether the file is created correctly after calling
+     ->create(), which means this approach doesn't work.
+D.
+   - easy to implement.
+   - the atomic behavaiour is lost.
+   - to open a file with superuser's credential and give it to a user
+     process is a bad idea, since the file object keeps the credential
+     in it. It may affect LSM or something. This approach doesn't work
+     either.
+
+The approach A is ideal, but it hard to implement. So here is a
+variation of A, which is to be implemented.
+
+A-1. Introduce aufs_atomic_open()
+     - calls branch fs ->atomic_open() if exists. otherwise calls
+       vfs_create() and finish_open().
+     - the demerit is that the several checks after branch fs
+       ->atomic_open() are lost. in the ordinary case, the checks are
+       done by VFS:do_last(), lookup_open() and atomic_open(). some can
+       be implemented in aufs, but not all I am afraid.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/03lookup.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/03lookup.txt
@@ -0,0 +1,113 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Lookup in a Branch
+----------------------------------------------------------------------
+Since aufs has a character of sub-VFS (see Introduction), it operates
+lookup for branches as VFS does. It may be a heavy work. But almost all
+lookup operation in aufs is the simplest case, ie. lookup only an entry
+directly connected to its parent. Digging down the directory hierarchy
+is unnecessary. VFS has a function lookup_one_len() for that use, and
+aufs calls it.
+
+When a branch is a remote filesystem, aufs basically relies upon its
+->d_revalidate(), also aufs forces the hardest revalidate tests for
+them.
+For d_revalidate, aufs implements three levels of revalidate tests. See
+"Revalidate Dentry and UDBA" in detail.
+
+
+Test Only the Highest One for the Directory Permission (dirperm1 option)
+----------------------------------------------------------------------
+Let's try case study.
+- aufs has two branches, upper readwrite and lower readonly.
+  /au = /rw + /ro
+- "dirA" exists under /ro, but /rw. and its mode is 0700.
+- user invoked "chmod a+rx /au/dirA"
+- the internal copy-up is activated and "/rw/dirA" is created and its
+  permission bits are set to world readable.
+- then "/au/dirA" becomes world readable?
+
+In this case, /ro/dirA is still 0700 since it exists in readonly branch,
+or it may be a natively readonly filesystem. If aufs respects the lower
+branch, it should not respond readdir request from other users. But user
+allowed it by chmod. Should really aufs rejects showing the entries
+under /ro/dirA?
+
+To be honest, I don't have a good solution for this case. So aufs
+implements 'dirperm1' and 'nodirperm1' mount options, and leave it to
+users.
+When dirperm1 is specified, aufs checks only the highest one for the
+directory permission, and shows the entries. Otherwise, as usual, checks
+every dir existing on all branches and rejects the request.
+
+As a side effect, dirperm1 option improves the performance of aufs
+because the number of permission check is reduced when the number of
+branch is many.
+
+
+Revalidate Dentry and UDBA (User's Direct Branch Access)
+----------------------------------------------------------------------
+Generally VFS helpers re-validate a dentry as a part of lookup.
+0. digging down the directory hierarchy.
+1. lock the parent dir by its i_mutex.
+2. lookup the final (child) entry.
+3. revalidate it.
+4. call the actual operation (create, unlink, etc.)
+5. unlock the parent dir
+
+If the filesystem implements its ->d_revalidate() (step 3), then it is
+called. Actually aufs implements it and checks the dentry on a branch is
+still valid.
+But it is not enough. Because aufs has to release the lock for the
+parent dir on a branch at the end of ->lookup() (step 2) and
+->d_revalidate() (step 3) while the i_mutex of the aufs dir is still
+held by VFS.
+If the file on a branch is changed directly, eg. bypassing aufs, after
+aufs released the lock, then the subsequent operation may cause
+something unpleasant result.
+
+This situation is a result of VFS architecture, ->lookup() and
+->d_revalidate() is separated. But I never say it is wrong. It is a good
+design from VFS's point of view. It is just not suitable for sub-VFS
+character in aufs.
+
+Aufs supports such case by three level of revalidation which is
+selectable by user.
+1. Simple Revalidate
+   Addition to the native flow in VFS's, confirm the child-parent
+   relationship on the branch just after locking the parent dir on the
+   branch in the "actual operation" (step 4). When this validation
+   fails, aufs returns EBUSY. ->d_revalidate() (step 3) in aufs still
+   checks the validation of the dentry on branches.
+2. Monitor Changes Internally by Inotify/Fsnotify
+   Addition to above, in the "actual operation" (step 4) aufs re-lookup
+   the dentry on the branch, and returns EBUSY if it finds different
+   dentry.
+   Additionally, aufs sets the inotify/fsnotify watch for every dir on branches
+   during it is in cache. When the event is notified, aufs registers a
+   function to kernel 'events' thread by schedule_work(). And the
+   function sets some special status to the cached aufs dentry and inode
+   private data. If they are not cached, then aufs has nothing to
+   do. When the same file is accessed through aufs (step 0-3) later,
+   aufs will detect the status and refresh all necessary data.
+   In this mode, aufs has to ignore the event which is fired by aufs
+   itself.
+3. No Extra Validation
+   This is the simplest test and doesn't add any additional revalidation
+   test, and skip the revalidation in step 4. It is useful and improves
+   aufs performance when system surely hide the aufs branches from user,
+   by over-mounting something (or another method).
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/04branch.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/04branch.txt
@@ -0,0 +1,74 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Branch Manipulation
+
+Since aufs supports dynamic branch manipulation, ie. add/remove a branch
+and changing its permission/attribute, there are a lot of works to do.
+
+
+Add a Branch
+----------------------------------------------------------------------
+o Confirm the adding dir exists outside of aufs, including loopback
+  mount, and its various attributes.
+o Initialize the xino file and whiteout bases if necessary.
+  See struct.txt.
+
+o Check the owner/group/mode of the directory
+  When the owner/group/mode of the adding directory differs from the
+  existing branch, aufs issues a warning because it may impose a
+  security risk.
+  For example, when a upper writable branch has a world writable empty
+  top directory, a malicious user can create any files on the writable
+  branch directly, like copy-up and modify manually. If something like
+  /etc/{passwd,shadow} exists on the lower readonly branch but the upper
+  writable branch, and the writable branch is world-writable, then a
+  malicious guy may create /etc/passwd on the writable branch directly
+  and the infected file will be valid in aufs.
+  I am afraid it can be a security issue, but aufs can do nothing except
+  producing a warning.
+
+
+Delete a Branch
+----------------------------------------------------------------------
+o Confirm the deleting branch is not busy
+  To be general, there is one merit to adopt "remount" interface to
+  manipulate branches. It is to discard caches. At deleting a branch,
+  aufs checks the still cached (and connected) dentries and inodes. If
+  there are any, then they are all in-use. An inode without its
+  corresponding dentry can be alive alone (for example, inotify/fsnotify case).
+
+  For the cached one, aufs checks whether the same named entry exists on
+  other branches.
+  If the cached one is a directory, because aufs provides a merged view
+  to users, as long as one dir is left on any branch aufs can show the
+  dir to users. In this case, the branch can be removed from aufs.
+  Otherwise aufs rejects deleting the branch.
+
+  If any file on the deleting branch is opened by aufs, then aufs
+  rejects deleting.
+
+
+Modify the Permission of a Branch
+----------------------------------------------------------------------
+o Re-initialize or remove the xino file and whiteout bases if necessary.
+  See struct.txt.
+
+o rw --> ro: Confirm the modifying branch is not busy
+  Aufs rejects the request if any of these conditions are true.
+  - a file on the branch is mmap-ed.
+  - a regular file on the branch is opened for write and there is no
+    same named entry on the upper branch.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/05wbr_policy.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/05wbr_policy.txt
@@ -0,0 +1,64 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Policies to Select One among Multiple Writable Branches
+----------------------------------------------------------------------
+When the number of writable branch is more than one, aufs has to decide
+the target branch for file creation or copy-up. By default, the highest
+writable branch which has the parent (or ancestor) dir of the target
+file is chosen (top-down-parent policy).
+By user's request, aufs implements some other policies to select the
+writable branch, for file creation several policies, round-robin,
+most-free-space, and other policies. For copy-up, top-down-parent,
+bottom-up-parent, bottom-up and others.
+
+As expected, the round-robin policy selects the branch in circular. When
+you have two writable branches and creates 10 new files, 5 files will be
+created for each branch. mkdir(2) systemcall is an exception. When you
+create 10 new directories, all will be created on the same branch.
+And the most-free-space policy selects the one which has most free
+space among the writable branches. The amount of free space will be
+checked by aufs internally, and users can specify its time interval.
+
+The policies for copy-up is more simple,
+top-down-parent is equivalent to the same named on in create policy,
+bottom-up-parent selects the writable branch where the parent dir
+exists and the nearest upper one from the copyup-source,
+bottom-up selects the nearest upper writable branch from the
+copyup-source, regardless the existence of the parent dir.
+
+There are some rules or exceptions to apply these policies.
+- If there is a readonly branch above the policy-selected branch and
+  the parent dir is marked as opaque (a variation of whiteout), or the
+  target (creating) file is whiteout-ed on the upper readonly branch,
+  then the result of the policy is ignored and the target file will be
+  created on the nearest upper writable branch than the readonly branch.
+- If there is a writable branch above the policy-selected branch and
+  the parent dir is marked as opaque or the target file is whiteouted
+  on the branch, then the result of the policy is ignored and the target
+  file will be created on the highest one among the upper writable
+  branches who has diropq or whiteout. In case of whiteout, aufs removes
+  it as usual.
+- link(2) and rename(2) systemcalls are exceptions in every policy.
+  They try selecting the branch where the source exists as possible
+  since copyup a large file will take long time. If it can't be,
+  ie. the branch where the source exists is readonly, then they will
+  follow the copyup policy.
+- There is an exception for rename(2) when the target exists.
+  If the rename target exists, aufs compares the index of the branches
+  where the source and the target exists and selects the higher
+  one. If the selected branch is readonly, then aufs follows the
+  copyup policy.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/06dirren.dot
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/06dirren.dot
@@ -0,0 +1,31 @@
+
+// to view this graph, run dot(1) command in GRAPHVIZ.
+
+digraph G {
+node [shape=box];
+whinfo [label="detailed info file\n(lower_brid_root-hinum, h_inum, namelen, old name)"];
+
+node [shape=oval];
+
+aufs_rename -> whinfo [label="store/remove"];
+
+node [shape=oval];
+inode_list [label="h_inum list in branch\ncache"];
+
+node [shape=box];
+whinode [label="h_inum list file"];
+
+node [shape=oval];
+brmgmt [label="br_add/del/mod/umount"];
+
+brmgmt -> inode_list [label="create/remove"];
+brmgmt -> whinode [label="load/store"];
+
+inode_list -> whinode [style=dashed,dir=both];
+
+aufs_rename -> inode_list [label="add/del"];
+
+aufs_lookup -> inode_list [label="search"];
+
+aufs_lookup -> whinfo [label="load/remove"];
+}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/06dirren.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/06dirren.txt
@@ -0,0 +1,102 @@
+
+# Copyright (C) 2017-2021 Junjiro R. Okajima
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Special handling for renaming a directory (DIRREN)
+----------------------------------------------------------------------
+First, let's assume we have a simple usecase.
+
+- /u = /rw + /ro
+- /rw/dirA exists
+- /ro/dirA and /ro/dirA/file exist too
+- there is no dirB on both branches
+- a user issues rename("dirA", "dirB")
+
+Now, what should aufs behave against this rename(2)?
+There are a few possible cases.
+
+A. returns EROFS.
+   since dirA exists on a readonly branch which cannot be renamed.
+B. returns EXDEV.
+   it is possible to copy-up dirA (only the dir itself), but the child
+   entries ("file" in this case) should not be. it must be a bad
+   approach to copy-up recursively.
+C. returns a success.
+   even the branch /ro is readonly, aufs tries renaming it. Obviously it
+   is a violation of aufs' policy.
+D. construct an extra information which indicates that /ro/dirA should
+   be handled as the name of dirB.
+   overlayfs has a similar feature called REDIRECT.
+
+Until now, aufs implements the case B only which returns EXDEV, and
+expects the userspace application behaves like mv(1) which tries
+issueing rename(2) recursively.
+
+A new aufs feature called DIRREN is introduced which implements the case
+D. There are several "extra information" added.
+
+1. detailed info per renamed directory
+   path: /rw/dirB/$AUFS_WH_DR_INFO_PFX.<lower branch-id>
+2. the inode-number list of directories on a branch
+   path: /rw/dirB/$AUFS_WH_DR_BRHINO
+
+The filename of "detailed info per directory" represents the lower
+branch, and its format is
+- a type of the branch id
+  one of these.
+  + uuid (not implemented yet)
+  + fsid
+  + dev
+- the inode-number of the branch root dir
+
+And it contains these info in a single regular file.
+- magic number
+- branch's inode-number of the logically renamed dir
+- the name of the before-renamed dir
+
+The "detailed info per directory" file is created in aufs rename(2), and
+loaded in any lookup.
+The info is considered in lookup for the matching case only. Here
+"matching" means that the root of branch (in the info filename) is same
+to the current looking-up branch. After looking-up the before-renamed
+name, the inode-number is compared. And the matched dentry is used.
+
+The "inode-number list of directories" is a regular file which contains
+simply the inode-numbers on the branch. The file is created or updated
+in removing the branch, and loaded in adding the branch. Its lifetime is
+equal to the branch.
+The list is refered in lookup, and when the current target inode is
+found in the list, the aufs tries loading the "detailed info per
+directory" and get the changed and valid name of the dir.
+
+Theoretically these "extra informaiton" may be able to be put into XATTR
+in the dir inode. But aufs doesn't choose this way because
+1. XATTR may not be supported by the branch (or its configuration)
+2. XATTR may have its size limit.
+3. XATTR may be less easy to convert than a regular file, when the
+   format of the info is changed in the future.
+At the same time, I agree that the regular file approach is much slower
+than XATTR approach. So, in the future, aufs may take the XATTR or other
+better approach.
+
+This DIRREN feature is enabled by aufs configuration, and is activated
+by a new mount option.
+
+For the more complicated case, there is a work with UDBA option, which
+is to dected the direct access to the branches (by-passing aufs) and to
+maintain the cashes in aufs. Since a single cached aufs dentry may
+contains two names, before- and after-rename, the name comparision in
+UDBA handler may not work correctly. In this case, the behaviour will be
+equivalen to udba=reval case.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/06fhsm.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/06fhsm.txt
@@ -0,0 +1,120 @@
+
+# Copyright (C) 2011-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+File-based Hierarchical Storage Management (FHSM)
+----------------------------------------------------------------------
+Hierarchical Storage Management (or HSM) is a well-known feature in the
+storage world. Aufs provides this feature as file-based with multiple
+writable branches, based upon the principle of "Colder, the Lower".
+Here the word "colder" means that the less used files, and "lower" means
+that the position in the order of the stacked branches vertically.
+These multiple writable branches are prioritized, ie. the topmost one
+should be the fastest drive and be used heavily.
+
+o Characters in aufs FHSM story
+- aufs itself and a new branch attribute.
+- a new ioctl interface to move-down and to establish a connection with
+  the daemon ("move-down" is a converse of "copy-up").
+- userspace tool and daemon.
+
+The userspace daemon establishes a connection with aufs and waits for
+the notification. The notified information is very similar to struct
+statfs containing the number of consumed blocks and inodes.
+When the consumed blocks/inodes of a branch exceeds the user-specified
+upper watermark, the daemon activates its move-down process until the
+consumed blocks/inodes reaches the user-specified lower watermark.
+
+The actual move-down is done by aufs based upon the request from
+user-space since we need to maintain the inode number and the internal
+pointer arrays in aufs.
+
+Currently aufs FHSM handles the regular files only. Additionally they
+must not be hard-linked nor pseudo-linked.
+
+
+o Cowork of aufs and the user-space daemon
+  During the userspace daemon established the connection, aufs sends a
+  small notification to it whenever aufs writes something into the
+  writable branch. But it may cost high since aufs issues statfs(2)
+  internally. So user can specify a new option to cache the
+  info. Actually the notification is controlled by these factors.
+  + the specified cache time.
+  + classified as "force" by aufs internally.
+  Until the specified time expires, aufs doesn't send the info
+  except the forced cases. When aufs decide forcing, the info is always
+  notified to userspace.
+  For example, the number of free inodes is generally large enough and
+  the shortage of it happens rarely. So aufs doesn't force the
+  notification when creating a new file, directory and others. This is
+  the typical case which aufs doesn't force.
+  When aufs writes the actual filedata and the files consumes any of new
+  blocks, the aufs forces notifying.
+
+
+o Interfaces in aufs
+- New branch attribute.
+  + fhsm
+    Specifies that the branch is managed by FHSM feature. In other word,
+    participant in the FHSM.
+    When nofhsm is set to the branch, it will not be the source/target
+    branch of the move-down operation. This attribute is set
+    independently from coo and moo attributes, and if you want full
+    FHSM, you should specify them as well.
+- New mount option.
+  + fhsm_sec
+    Specifies a second to suppress many less important info to be
+    notified.
+- New ioctl.
+  + AUFS_CTL_FHSM_FD
+    create a new file descriptor which userspace can read the notification
+    (a subset of struct statfs) from aufs.
+- Module parameter 'brs'
+  It has to be set to 1. Otherwise the new mount option 'fhsm' will not
+  be set.
+- mount helpers /sbin/mount.aufs and /sbin/umount.aufs
+  When there are two or more branches with fhsm attributes,
+  /sbin/mount.aufs invokes the user-space daemon and /sbin/umount.aufs
+  terminates it. As a result of remounting and branch-manipulation, the
+  number of branches with fhsm attribute can be one. In this case,
+  /sbin/mount.aufs will terminate the user-space daemon.
+
+
+Finally the operation is done as these steps in kernel-space.
+- make sure that,
+  + no one else is using the file.
+  + the file is not hard-linked.
+  + the file is not pseudo-linked.
+  + the file is a regular file.
+  + the parent dir is not opaqued.
+- find the target writable branch.
+- make sure the file is not whiteout-ed by the upper (than the target)
+  branch.
+- make the parent dir on the target branch.
+- mutex lock the inode on the branch.
+- unlink the whiteout on the target branch (if exists).
+- lookup and create the whiteout-ed temporary name on the target branch.
+- copy the file as the whiteout-ed temporary name on the target branch.
+- rename the whiteout-ed temporary name to the original name.
+- unlink the file on the source branch.
+- maintain the internal pointer array and the external inode number
+  table (XINO).
+- maintain the timestamps and other attributes of the parent dir and the
+  file.
+
+And of course, in every step, an error may happen. So the operation
+should restore the original file state after an error happens.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/06mmap.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/06mmap.txt
@@ -0,0 +1,72 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+mmap(2) -- File Memory Mapping
+----------------------------------------------------------------------
+In aufs, the file-mapped pages are handled by a branch fs directly, no
+interaction with aufs. It means aufs_mmap() calls the branch fs's
+->mmap().
+This approach is simple and good, but there is one problem.
+Under /proc, several entries show the mmapped files by its path (with
+device and inode number), and the printed path will be the path on the
+branch fs's instead of virtual aufs's.
+This is not a problem in most cases, but some utilities lsof(1) (and its
+user) may expect the path on aufs.
+
+To address this issue, aufs adds a new member called vm_prfile in struct
+vm_area_struct (and struct vm_region). The original vm_file points to
+the file on the branch fs in order to handle everything correctly as
+usual. The new vm_prfile points to a virtual file in aufs, and the
+show-functions in procfs refers to vm_prfile if it is set.
+Also we need to maintain several other places where touching vm_file
+such like
+- fork()/clone() copies vma and the reference count of vm_file is
+  incremented.
+- merging vma maintains the ref count too.
+
+This is not a good approach. It just fakes the printed path. But it
+leaves all behaviour around f_mapping unchanged. This is surely an
+advantage.
+Actually aufs had adopted another complicated approach which calls
+generic_file_mmap() and handles struct vm_operations_struct. In this
+approach, aufs met a hard problem and I could not solve it without
+switching the approach.
+
+There may be one more another approach which is
+- bind-mount the branch-root onto the aufs-root internally
+- grab the new vfsmount (ie. struct mount)
+- lazy-umount the branch-root internally
+- in open(2) the aufs-file, open the branch-file with the hidden
+  vfsmount (instead of the original branch's vfsmount)
+- ideally this "bind-mount and lazy-umount" should be done atomically,
+  but it may be possible from userspace by the mount helper.
+
+Adding the internal hidden vfsmount and using it in opening a file, the
+file path under /proc will be printed correctly. This approach looks
+smarter, but is not possible I am afraid.
+- aufs-root may be bind-mount later. when it happens, another hidden
+  vfsmount will be required.
+- it is hard to get the chance to bind-mount and lazy-umount
+  + in kernel-space, FS can have vfsmount in open(2) via
+    file->f_path, and aufs can know its vfsmount. But several locks are
+    already acquired, and if aufs tries to bind-mount and lazy-umount
+    here, then it may cause a deadlock.
+  + in user-space, bind-mount doesn't invoke the mount helper.
+- since /proc shows dev and ino, aufs has to give vma these info. it
+  means a new member vm_prinode will be necessary. this is essentially
+  equivalent to vm_prfile described above.
+
+I have to give up this "looks-smater" approach.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/06xattr.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/06xattr.txt
@@ -0,0 +1,96 @@
+
+# Copyright (C) 2014-2021 Junjiro R. Okajima
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+Listing XATTR/EA and getting the value
+----------------------------------------------------------------------
+For the inode standard attributes (owner, group, timestamps, etc.), aufs
+shows the values from the topmost existing file. This behaviour is good
+for the non-dir entries since the bahaviour exactly matches the shown
+information. But for the directories, aufs considers all the same named
+entries on the lower branches. Which means, if one of the lower entry
+rejects readdir call, then aufs returns an error even if the topmost
+entry allows it. This behaviour is necessary to respect the branch fs's
+security, but can make users confused since the user-visible standard
+attributes don't match the behaviour.
+To address this issue, aufs has a mount option called dirperm1 which
+checks the permission for the topmost entry only, and ignores the lower
+entry's permission.
+
+A similar issue can happen around XATTR.
+getxattr(2) and listxattr(2) families behave as if dirperm1 option is
+always set. Otherwise these very unpleasant situation would happen.
+- listxattr(2) may return the duplicated entries.
+- users may not be able to remove or reset the XATTR forever,
+
+
+XATTR/EA support in the internal (copy,move)-(up,down)
+----------------------------------------------------------------------
+Generally the extended attributes of inode are categorized as these.
+- "security" for LSM and capability.
+- "system" for posix ACL, 'acl' mount option is required for the branch
+  fs generally.
+- "trusted" for userspace, CAP_SYS_ADMIN is required.
+- "user" for userspace, 'user_xattr' mount option is required for the
+  branch fs generally.
+
+Moreover there are some other categories. Aufs handles these rather
+unpopular categories as the ordinary ones, ie. there is no special
+condition nor exception.
+
+In copy-up, the support for XATTR on the dst branch may differ from the
+src branch. In this case, the copy-up operation will get an error and
+the original user operation which triggered the copy-up will fail. It
+can happen that even all copy-up will fail.
+When both of src and dst branches support XATTR and if an error occurs
+during copying XATTR, then the copy-up should fail obviously. That is a
+good reason and aufs should return an error to userspace. But when only
+the src branch support that XATTR, aufs should not return an error.
+For example, the src branch supports ACL but the dst branch doesn't
+because the dst branch may natively un-support it or temporary
+un-support it due to "noacl" mount option. Of course, the dst branch fs
+may NOT return an error even if the XATTR is not supported. It is
+totally up to the branch fs.
+
+Anyway when the aufs internal copy-up gets an error from the dst branch
+fs, then aufs tries removing the just copied entry and returns the error
+to the userspace. The worst case of this situation will be all copy-up
+will fail.
+
+For the copy-up operation, there two basic approaches.
+- copy the specified XATTR only (by category above), and return the
+  error unconditionally if it happens.
+- copy all XATTR, and ignore the error on the specified category only.
+
+In order to support XATTR and to implement the correct behaviour, aufs
+chooses the latter approach and introduces some new branch attributes,
+"icexsec", "icexsys", "icextr", "icexusr", and "icexoth".
+They correspond to the XATTR namespaces (see above). Additionally, to be
+convenient, "icex" is also provided which means all "icex*" attributes
+are set (here the word "icex" stands for "ignore copy-error on XATTR").
+
+The meaning of these attributes is to ignore the error from setting
+XATTR on that branch.
+Note that aufs tries copying all XATTR unconditionally, and ignores the
+error from the dst branch according to the specified attributes.
+
+Some XATTR may have its default value. The default value may come from
+the parent dir or the environment. If the default value is set at the
+file creating-time, it will be overwritten by copy-up.
+Some contradiction may happen I am afraid.
+Do we need another attribute to stop copying XATTR? I am unsure. For
+now, aufs implements the branch attributes to ignore the error.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/07export.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/07export.txt
@@ -0,0 +1,58 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Export Aufs via NFS
+----------------------------------------------------------------------
+Here is an approach.
+- like xino/xib, add a new file 'xigen' which stores aufs inode
+  generation.
+- iget_locked(): initialize aufs inode generation for a new inode, and
+  store it in xigen file.
+- destroy_inode(): increment aufs inode generation and store it in xigen
+  file. it is necessary even if it is not unlinked, because any data of
+  inode may be changed by UDBA.
+- encode_fh(): for a root dir, simply return FILEID_ROOT. otherwise
+  build file handle by
+  + branch id (4 bytes)
+  + superblock generation (4 bytes)
+  + inode number (4 or 8 bytes)
+  + parent dir inode number (4 or 8 bytes)
+  + inode generation (4 bytes))
+  + return value of exportfs_encode_fh() for the parent on a branch (4
+    bytes)
+  + file handle for a branch (by exportfs_encode_fh())
+- fh_to_dentry():
+  + find the index of a branch from its id in handle, and check it is
+    still exist in aufs.
+  + 1st level: get the inode number from handle and search it in cache.
+  + 2nd level: if not found in cache, get the parent inode number from
+    the handle and search it in cache. and then open the found parent
+    dir, find the matching inode number by vfs_readdir() and get its
+    name, and call lookup_one_len() for the target dentry.
+  + 3rd level: if the parent dir is not cached, call
+    exportfs_decode_fh() for a branch and get the parent on a branch,
+    build a pathname of it, convert it a pathname in aufs, call
+    path_lookup(). now aufs gets a parent dir dentry, then handle it as
+    the 2nd level.
+  + to open the dir, aufs needs struct vfsmount. aufs keeps vfsmount
+    for every branch, but not itself. to get this, (currently) aufs
+    searches in current->nsproxy->mnt_ns list. it may not be a good
+    idea, but I didn't get other approach.
+  + test the generation of the gotten inode.
+- every inode operation: they may get EBUSY due to UDBA. in this case,
+  convert it into ESTALE for NFSD.
+- readdir(): call lockdep_on/off() because filldir in NFSD calls
+  lookup_one_len(), vfs_getattr(), encode_fh() and others.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/08shwh.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/08shwh.txt
@@ -0,0 +1,52 @@
+
+# Copyright (C) 2005-2021 Junjiro R. Okajima
+# 
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+# 
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+# 
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Show Whiteout Mode (shwh)
+----------------------------------------------------------------------
+Generally aufs hides the name of whiteouts. But in some cases, to show
+them is very useful for users. For instance, creating a new middle layer
+(branch) by merging existing layers.
+
+(borrowing aufs1 HOW-TO from a user, Michael Towers)
+When you have three branches,
+- Bottom: 'system', squashfs (underlying base system), read-only
+- Middle: 'mods', squashfs, read-only
+- Top: 'overlay', ram (tmpfs), read-write
+
+The top layer is loaded at boot time and saved at shutdown, to preserve
+the changes made to the system during the session.
+When larger changes have been made, or smaller changes have accumulated,
+the size of the saved top layer data grows. At this point, it would be
+nice to be able to merge the two overlay branches ('mods' and 'overlay')
+and rewrite the 'mods' squashfs, clearing the top layer and thus
+restoring save and load speed.
+
+This merging is simplified by the use of another aufs mount, of just the
+two overlay branches using the 'shwh' option.
+# mount -t aufs -o ro,shwh,br:/livesys/overlay=ro+wh:/livesys/mods=rr+wh \
+	aufs /livesys/merge_union
+
+A merged view of these two branches is then available at
+/livesys/merge_union, and the new feature is that the whiteouts are
+visible!
+Note that in 'shwh' mode the aufs mount must be 'ro', which will disable
+writing to all branches. Also the default mode for all branches is 'ro'.
+It is now possible to save the combined contents of the two overlay
+branches to a new squashfs, e.g.:
+# mksquashfs /livesys/merge_union /path/to/newmods.squash
+
+This new squashfs archive can be stored on the boot device and the
+initramfs will use it to replace the old one at the next boot.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/aufs/design/10dynop.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/aufs/design/10dynop.txt
@@ -0,0 +1,47 @@
+
+# Copyright (C) 2010-2021 Junjiro R. Okajima
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+Dynamically customizable FS operations
+----------------------------------------------------------------------
+Generally FS operations (struct inode_operations, struct
+address_space_operations, struct file_operations, etc.) are defined as
+"static const", but it never means that FS have only one set of
+operation. Some FS have multiple sets of them. For instance, ext2 has
+three sets, one for XIP, for NOBH, and for normal.
+Since aufs overrides and redirects these operations, sometimes aufs has
+to change its behaviour according to the branch FS type. More importantly
+VFS acts differently if a function (member in the struct) is set or
+not. It means aufs should have several sets of operations and select one
+among them according to the branch FS definition.
+
+In order to solve this problem and not to affect the behaviour of VFS,
+aufs defines these operations dynamically. For instance, aufs defines
+dummy direct_IO function for struct address_space_operations, but it may
+not be set to the address_space_operations actually. When the branch FS
+doesn't have it, aufs doesn't set it to its address_space_operations
+while the function definition itself is still alive. So the behaviour
+itself will not change, and it will return an error when direct_IO is
+not set.
+
+The lifetime of these dynamically generated operation object is
+maintained by aufs branch object. When the branch is removed from aufs,
+the reference counter of the object is decremented. When it reaches
+zero, the dynamically generated operation object will be freed.
+
+This approach is designed to support AIO (io_submit), Direct I/O and
+XIP (DAX) mainly.
+Currently this approach is applied to address_space_operations for
+regular files only.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/autofs-mount-control.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/autofs-mount-control.rst
@@ -196,7 +196,7 @@
 		    struct args_ismountpoint	ismountpoint;
 	    };
 
-	    char path[0];
+	    char path[];
     };
 
 The ioctlfd field is a mount point file descriptor of an autofs mount
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/autofs.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/autofs.rst
@@ -467,7 +467,7 @@
 			struct args_ismountpoint	ismountpoint;
 		};
 
-                char path[0];
+                char path[];
         };
 
 For the **OPEN_MOUNT** and **IS_MOUNTPOINT** commands, the target
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/directory-locking.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/directory-locking.rst
@@ -23,13 +23,15 @@
 locks victim and calls the method.  Locks are exclusive.
 
 4) rename() that is _not_ cross-directory.  Locking rules: caller locks
-the parent and finds source and target.  In case of exchange (with
-RENAME_EXCHANGE in flags argument) lock both.  In any case,
-if the target already exists, lock it.  If the source is a non-directory,
-lock it.  If we need to lock both, lock them in inode pointer order.
-Then call the method.  All locks are exclusive.
-NB: we might get away with locking the source (and target in exchange
-case) shared.
+the parent and finds source and target.  Then we decide which of the
+source and target need to be locked.  Source needs to be locked if it's a
+non-directory; target - if it's a non-directory or about to be removed.
+Take the locks that need to be taken, in inode pointer order if need
+to take both (that can happen only when both source and target are
+non-directories - the source because it wouldn't be locked otherwise
+and the target because mixing directory and non-directory is allowed
+only with RENAME_EXCHANGE, and that won't be removing the target).
+After the locks had been taken, call the method.  All locks are exclusive.
 
 5) link creation.  Locking rules:
 
@@ -44,19 +46,18 @@
 rules:
 
 	* lock the filesystem
-	* lock parents in "ancestors first" order.
+	* lock parents in "ancestors first" order. If one is not ancestor of
+	  the other, lock the parent of source first.
 	* find source and target.
 	* if old parent is equal to or is a descendent of target
 	  fail with -ENOTEMPTY
 	* if new parent is equal to or is a descendent of source
 	  fail with -ELOOP
-	* If it's an exchange, lock both the source and the target.
-	* If the target exists, lock it.  If the source is a non-directory,
-	  lock it.  If we need to lock both, do so in inode pointer order.
+	* Lock subdirectories involved (source before target).
+	* Lock non-directories involved, in inode pointer order.
 	* call the method.
 
-All ->i_rwsem are taken exclusive.  Again, we might get away with locking
-the source (and target in exchange case) shared.
+All ->i_rwsem are taken exclusive.
 
 The rules above obviously guarantee that all directories that are going to be
 read, modified or removed by method will be locked by caller.
@@ -66,8 +67,10 @@
 
 Proof:
 
-	First of all, at any moment we have a partial ordering of the
-	objects - A < B iff A is an ancestor of B.
+[XXX: will be updated once we are done massaging the lock_rename()]
+	First of all, at any moment we have a linear ordering of the
+	objects - A < B iff (A is an ancestor of B) or (B is not an ancestor
+        of A and ptr(A) < ptr(B)).
 
 	That ordering can change.  However, the following is true:
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/ext4/attributes.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/ext4/attributes.rst
@@ -76,7 +76,7 @@
      - Checksum of the extended attribute block.
    * - 0x14
      - \_\_u32
-     - h\_reserved[2]
+     - h\_reserved[3]
      - Zero.
 
 The checksum is calculated against the FS UUID, the 64-bit block number
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/f2fs.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/f2fs.rst
@@ -197,6 +197,7 @@
 			 FAULT_DISCARD		  0x000002000
 			 FAULT_WRITE_IO		  0x000004000
 			 FAULT_SLAB_ALLOC	  0x000008000
+			 FAULT_DQUOT_INIT	  0x000010000
 			 ===================	  ===========
 mode=%s			 Control block allocation mode which supports "adaptive"
 			 and "lfs". In "lfs" mode, there should be no random
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/fscrypt.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/fscrypt.rst
@@ -176,11 +176,11 @@
 
 Each encrypted directory tree is protected by a *master key*.  Master
 keys can be up to 64 bytes long, and must be at least as long as the
-greater of the key length needed by the contents and filenames
-encryption modes being used.  For example, if AES-256-XTS is used for
-contents encryption, the master key must be 64 bytes (512 bits).  Note
-that the XTS mode is defined to require a key twice as long as that
-required by the underlying block cipher.
+greater of the security strength of the contents and filenames
+encryption modes being used.  For example, if any AES-256 mode is
+used, the master key must be at least 256 bits, i.e. 32 bytes.  A
+stricter requirement applies if the key is used by a v1 encryption
+policy and AES-256-XTS is used; such keys must be 64 bytes.
 
 To "unlock" an encrypted directory tree, userspace must provide the
 appropriate master key.  There can be any number of master keys, each
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/idmappings.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/idmappings.rst
@@ -952,75 +952,3 @@
 their home directory back to their home computer where they are assigned
 ``u1000`` using the initial idmapping and mount the filesystem with the initial
 idmapping they will see all those files owned by ``u1000``.
-
-Shortcircuting
---------------
-
-Currently, the implementation of idmapped mounts enforces that the filesystem
-is mounted with the initial idmapping. The reason is simply that none of the
-filesystems that we targeted were mountable with a non-initial idmapping. But
-that might change soon enough. As we've seen above, thanks to the properties of
-idmappings the translation works for both filesystems mounted with the initial
-idmapping and filesystem with non-initial idmappings.
-
-Based on this current restriction to filesystem mounted with the initial
-idmapping two noticeable shortcuts have been taken:
-
-1. We always stash a reference to the initial user namespace in ``struct
-   vfsmount``. Idmapped mounts are thus mounts that have a non-initial user
-   namespace attached to them.
-
-   In order to support idmapped mounts this needs to be changed. Instead of
-   stashing the initial user namespace the user namespace the filesystem was
-   mounted with must be stashed. An idmapped mount is then any mount that has
-   a different user namespace attached then the filesystem was mounted with.
-   This has no user-visible consequences.
-
-2. The translation algorithms in ``mapped_fs*id()`` and ``i_*id_into_mnt()``
-   are simplified.
-
-   Let's consider ``mapped_fs*id()`` first. This function translates the
-   caller's kernel id into a kernel id in the filesystem's idmapping via
-   a mount's idmapping. The full algorithm is::
-
-    mapped_fsuid(kid):
-      /* Map the kernel id up into a userspace id in the mount's idmapping. */
-      from_kuid(mount-idmapping, kid) = uid
-
-      /* Map the userspace id down into a kernel id in the filesystem's idmapping. */
-      make_kuid(filesystem-idmapping, uid) = kuid
-
-   We know that the filesystem is always mounted with the initial idmapping as
-   we enforce this in ``mount_setattr()``. So this can be shortened to::
-
-    mapped_fsuid(kid):
-      /* Map the kernel id up into a userspace id in the mount's idmapping. */
-      from_kuid(mount-idmapping, kid) = uid
-
-      /* Map the userspace id down into a kernel id in the filesystem's idmapping. */
-      KUIDT_INIT(uid) = kuid
-
-   Similarly, for ``i_*id_into_mnt()`` which translated the filesystem's kernel
-   id into a mount's kernel id::
-
-    i_uid_into_mnt(kid):
-      /* Map the kernel id up into a userspace id in the filesystem's idmapping. */
-      from_kuid(filesystem-idmapping, kid) = uid
-
-      /* Map the userspace id down into a kernel id in the mounts's idmapping. */
-      make_kuid(mount-idmapping, uid) = kuid
-
-   Again, we know that the filesystem is always mounted with the initial
-   idmapping as we enforce this in ``mount_setattr()``. So this can be
-   shortened to::
-
-    i_uid_into_mnt(kid):
-      /* Map the kernel id up into a userspace id in the filesystem's idmapping. */
-      __kuid_val(kid) = uid
-
-      /* Map the userspace id down into a kernel id in the mounts's idmapping. */
-      make_kuid(mount-idmapping, uid) = kuid
-
-Handling filesystems mounted with non-initial idmappings requires that the
-translation functions be converted to their full form. They can still be
-shortcircuited on non-idmapped mounts. This has no user-visible consequences.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/locking.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/locking.rst
@@ -98,7 +98,7 @@
 mkdir:		exclusive
 unlink:		exclusive (both)
 rmdir:		exclusive (both)(see below)
-rename:		exclusive (all)	(see below)
+rename:		exclusive (both parents, some children)	(see below)
 readlink:	no
 get_link:	no
 setattr:	exclusive
@@ -118,6 +118,9 @@
 	Additionally, ->rmdir(), ->unlink() and ->rename() have ->i_rwsem
 	exclusive on victim.
 	cross-directory ->rename() has (per-superblock) ->s_vfs_rename_sem.
+	->unlink() and ->rename() have ->i_rwsem exclusive on all non-directories
+	involved.
+	->rename() has ->i_rwsem exclusive on any subdirectory that changes parent.
 
 See Documentation/filesystems/directory-locking.rst for more detailed discussion
 of the locking scheme for directory operations.
@@ -439,17 +442,21 @@
 	void (*lm_break)(struct file_lock *); /* break_lease callback */
 	int (*lm_change)(struct file_lock **, int);
 	bool (*lm_breaker_owns_lease)(struct file_lock *);
+        bool (*lm_lock_expirable)(struct file_lock *);
+        void (*lm_expire_lock)(void);
 
 locking rules:
 
 ======================	=============	=================	=========
-ops			inode->i_lock	blocked_lock_lock	may block
+ops			   flc_lock  	blocked_lock_lock	may block
 ======================	=============	=================	=========
-lm_notify:		yes		yes			no
+lm_notify:		no      	yes			no
 lm_grant:		no		no			no
 lm_break:		yes		no			no
 lm_change		yes		no			no
-lm_breaker_owns_lease:	no		no			no
+lm_breaker_owns_lease:	yes     	no			no
+lm_lock_expirable	yes		no			no
+lm_expire_lock		no		no			yes
 ======================	=============	=================	=========
 
 buffer_head
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/mount_api.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/mount_api.rst
@@ -778,7 +778,8 @@
 
    * ::
 
-       bool fs_validate_description(const struct fs_parameter_description *desc);
+       bool fs_validate_description(const char *name,
+                                    const struct fs_parameter_description *desc);
 
      This performs some validation checks on a parameter description.  It
      returns true if the description is good and false if it is not.  It will
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/nfs/exporting.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/nfs/exporting.rst
@@ -215,3 +215,29 @@
     This flag causes nfsd to close any open files for this inode _before_
     calling into the vfs to do an unlink or a rename that would replace
     an existing file.
+
+  EXPORT_OP_REMOTE_FS - Backing storage for this filesystem is remote
+    PF_LOCAL_THROTTLE exists for loopback NFSD, where a thread needs to
+    write to one bdi (the final bdi) in order to free up writes queued
+    to another bdi (the client bdi). Such threads get a private balance
+    of dirty pages so that dirty pages for the client bdi do not imact
+    the daemon writing to the final bdi. For filesystems whose durable
+    storage is not local (such as exported NFS filesystems), this
+    constraint has negative consequences. EXPORT_OP_REMOTE_FS enables
+    an export to disable writeback throttling.
+
+  EXPORT_OP_NOATOMIC_ATTR - Filesystem does not update attributes atomically
+    EXPORT_OP_NOATOMIC_ATTR indicates that the exported filesystem
+    cannot provide the semantics required by the "atomic" boolean in
+    NFSv4's change_info4. This boolean indicates to a client whether the
+    returned before and after change attributes were obtained atomically
+    with the respect to the requested metadata operation (UNLINK,
+    OPEN/CREATE, MKDIR, etc).
+
+  EXPORT_OP_FLUSH_ON_CLOSE - Filesystem flushes file data on close(2)
+    On most filesystems, inodes can remain under writeback after the
+    file is closed. NFSD relies on client activity or local flusher
+    threads to handle writeback. Certain filesystems, such as NFS, flush
+    all of an inode's dirty data on last close. Exports that behave this
+    way should set EXPORT_OP_FLUSH_ON_CLOSE so that NFSD knows to skip
+    waiting for writeback when closing such files.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/porting.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/porting.rst
@@ -908,3 +908,21 @@
 instead of passing mount and dentry separately.  For callers that used to
 pass <mnt, mnt->mnt_root> pair (i.e. the root of given mount), a new helper
 is provided - file_open_root_mnt().  In-tree users adjusted.
+
+---
+
+**mandatory**
+
+If ->rename() update of .. on cross-directory move needs an exclusion with
+directory modifications, do *not* lock the subdirectory in question in your
+->rename() - it's done by the caller now [that item should've been added in
+28eceeda130f "fs: Lock moved directories"].
+
+---
+
+**mandatory**
+
+On same-directory ->rename() the (tautological) update of .. is not protected
+by any locks; just don't do it if the old parent is the same as the new one.
+We really can't lock two subdirectories in same-directory rename - not without
+deadlocks.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/filesystems/vfs.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/filesystems/vfs.rst
@@ -274,6 +274,9 @@
 	This is specifically for the inode itself being marked dirty,
 	not its data.  If the update needs to be persisted by fdatasync(),
 	then I_DIRTY_DATASYNC will be set in the flags argument.
+	I_DIRTY_TIME will be set in the flags in case lazytime is enabled
+	and struct inode has times updated since the last ->dirty_inode
+	call.
 
 ``write_inode``
 	this method is called when the VFS needs to write an inode to
@@ -1207,7 +1210,7 @@
 	return
 	-ECHILD and it will be called again in ref-walk mode.
 
-``_weak_revalidate``
+``d_weak_revalidate``
 	called when the VFS needs to revalidate a "jumped" dentry.  This
 	is called when a path-walk ends at dentry that was not acquired
 	by doing a lookup in the parent directory.  This includes "/",
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/firmware-guide/acpi/apei/einj.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/firmware-guide/acpi/apei/einj.rst
@@ -168,7 +168,7 @@
   0x00000008	Memory Correctable
   0x00000010	Memory Uncorrectable non-fatal
   # echo 0x12345000 > param1		# Set memory address for injection
-  # echo $((-1 << 12)) > param2		# Mask 0xfffffffffffff000 - anywhere in this page
+  # echo 0xfffffffffffff000 > param2		# Mask - anywhere in this page
   # echo 0x8 > error_type			# Choose correctable memory error
   # echo 1 > error_inject			# Inject now
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/firmware-guide/acpi/dsd/data-node-references.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/firmware-guide/acpi/dsd/data-node-references.rst
@@ -5,7 +5,7 @@
 Referencing hierarchical data nodes
 ===================================
 
-:Copyright: |copy| 2018 Intel Corporation
+:Copyright: |copy| 2018, 2021 Intel Corporation
 :Author: Sakari Ailus <sakari.ailus@linux.intel.com>
 
 ACPI in general allows referring to device objects in the tree only.
@@ -52,12 +52,14 @@
 	    Name (NOD0, Package() {
 		ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
 		Package () {
+		    Package () { "reg", 0 },
 		    Package () { "random-property", 3 },
 		}
 	    })
 	    Name (NOD1, Package() {
 		ToUUID("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
 		Package () {
+		    Package () { "reg", 1 },
 		    Package () { "anothernode", "ANOD" },
 		}
 	    })
@@ -74,7 +76,11 @@
 	    Name (_DSD, Package () {
 		ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
 		Package () {
-		    Package () { "reference", ^DEV0, "node@1", "anothernode" },
+		    Package () {
+			"reference", Package () {
+			    ^DEV0, "node@1", "anothernode"
+			}
+		    },
 		}
 	    })
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/gpu/i915.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/gpu/i915.rst
@@ -183,25 +183,25 @@
 Display Refresh Rate Switching (DRRS)
 -------------------------------------
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :doc: Display Refresh Rate Switching (DRRS)
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :functions: intel_dp_set_drrs_state
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :functions: intel_edp_drrs_enable
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :functions: intel_edp_drrs_disable
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :functions: intel_edp_drrs_invalidate
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :functions: intel_edp_drrs_flush
 
-.. kernel-doc:: drivers/gpu/drm/i915/display/intel_dp.c
+.. kernel-doc:: drivers/gpu/drm/i915/display/intel_drrs.c
    :functions: intel_dp_drrs_init
 
 DPIO
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/gpu/todo.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/gpu/todo.rst
@@ -311,27 +311,6 @@
 
 Level: Advanced
 
-Garbage collect fbdev scrolling acceleration
---------------------------------------------
-
-Scroll acceleration is disabled in fbcon by hard-wiring p->scrollmode =
-SCROLL_REDRAW. There's a ton of code this will allow us to remove:
-
-- lots of code in fbcon.c
-
-- a bunch of the hooks in fbcon_ops, maybe the remaining hooks could be called
-  directly instead of the function table (with a switch on p->rotate)
-
-- fb_copyarea is unused after this, and can be deleted from all drivers
-
-Note that not all acceleration code can be deleted, since clearing and cursor
-support is still accelerated, which might be good candidates for further
-deletion projects.
-
-Contact: Daniel Vetter
-
-Level: Intermediate
-
 idr_init_base()
 ---------------
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/hwmon/ftsteutates.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/hwmon/ftsteutates.rst
@@ -22,6 +22,10 @@
 8 fans. It also contains an integrated watchdog which is currently
 implemented in this driver.
 
+The 4 voltages require a board-specific multiplier, since the BMC can
+only measure voltages up to 3.3V and thus relies on voltage dividers.
+Consult your motherboard manual for details.
+
 To clear a temperature or fan alarm, execute the following command with the
 correct path to the alarm file::
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/hwmon/lm90.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/hwmon/lm90.rst
@@ -265,6 +265,16 @@
 
 	       https://www.ti.com/litv/pdf/sbos686
 
+  * Texas Instruments TMP461
+
+    Prefix: 'tmp461'
+
+    Addresses scanned: I2C 0x48 through 0x4F
+
+    Datasheet: Publicly available at TI website
+
+	       https://www.ti.com/lit/gpn/tmp461
+
 Author: Jean Delvare <jdelvare@suse.de>
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/input/joydev/joystick.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/input/joydev/joystick.rst
@@ -517,6 +517,7 @@
 * AVB Mag Turbo Force
 * AVB Top Shot Pegasus
 * AVB Top Shot Force Feedback Racing Wheel
+* Boeder Force Feedback Wheel
 * Logitech WingMan Force
 * Logitech WingMan Force Wheel
 * Guillemot Race Leader Force Feedback
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/kbuild/kconfig.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/kbuild/kconfig.rst
@@ -54,6 +54,15 @@
 If you set KCONFIG_OVERWRITECONFIG in the environment, Kconfig will not
 break symlinks when .config is a symlink to somewhere else.
 
+KCONFIG_WARN_UNKNOWN_SYMBOLS
+----------------------------
+This environment variable makes Kconfig warn about all unrecognized
+symbols in the config input.
+
+KCONFIG_WERROR
+--------------
+If set, Kconfig treats warnings as errors.
+
 `CONFIG_`
 ---------
 If you set `CONFIG_` in the environment, Kconfig will prefix all symbols
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/kernel-hacking/locking.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/kernel-hacking/locking.rst
@@ -1352,7 +1352,7 @@
 Futex API reference
 ===================
 
-.. kernel-doc:: kernel/futex.c
+.. kernel-doc:: kernel/futex/core.c
    :internal:
 
 Further reading
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/locking/hwspinlock.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/locking/hwspinlock.rst
@@ -87,6 +87,17 @@
 
 ::
 
+  int hwspin_lock_bust(struct hwspinlock *hwlock, unsigned int id);
+
+After verifying the owner of the hwspinlock, release a previously acquired
+hwspinlock; returns 0 on success, or an appropriate error code on failure
+(e.g. -EOPNOTSUPP if the bust operation is not defined for the specific
+hwspinlock).
+
+Should be called from a process context (might sleep).
+
+::
+
   int hwspin_lock_timeout(struct hwspinlock *hwlock, unsigned int timeout);
 
 Lock a previously-assigned hwspinlock with a timeout limit (specified in
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/locking/locktypes.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/locking/locktypes.rst
@@ -439,11 +439,9 @@
   spin_lock(&p->lock);
   p->count += this_cpu_read(var2);
 
-On a non-PREEMPT_RT kernel migrate_disable() maps to preempt_disable()
-which makes the above code fully equivalent. On a PREEMPT_RT kernel
 migrate_disable() ensures that the task is pinned on the current CPU which
 in turn guarantees that the per-CPU access to var1 and var2 are staying on
-the same CPU.
+the same CPU while the task remains preemptible.
 
 The migrate_disable() substitution is not valid for the following
 scenario::
@@ -456,9 +454,8 @@
     p = this_cpu_ptr(&var1);
     p->val = func2();
 
-While correct on a non-PREEMPT_RT kernel, this breaks on PREEMPT_RT because
-here migrate_disable() does not protect against reentrancy from a
-preempting task. A correct substitution for this case is::
+This breaks because migrate_disable() does not protect against reentrancy from
+a preempting task. A correct substitution for this case is::
 
   func()
   {
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/locking/seqlock.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/locking/seqlock.rst
@@ -153,7 +153,7 @@
 from interruption by readers. This is typically the case when the read
 side can be invoked from NMI handlers.
 
-Check `raw_write_seqcount_latch()` for more information.
+Check `write_seqcount_latch()` for more information.
 
 
 .. _seqlock_t:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/misc-devices/xilinx_flex.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/misc-devices/xilinx_flex.txt
@@ -0,0 +1,66 @@
+Kernel driver xilinx_flex
+============================
+
+Supported chips:
+Versal SOC
+
+Author:
+	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+Description
+-----------
+
+Versal uses the Arteris FlexNoC interconnect instead of the ARM NIC. FlexNoC
+provides the capability to integrate performance counters in the interconnect.
+It has configurable probe points to monitor the packet and forwards it to
+observer for logging. It supports read and write transaction counts for
+request and response.
+
+Features:
+---> Run-time programmable selection of packet probe points.
+---> Recording of traffic and link statistics.
+---> Separate read and write response and request count.
+
+SYSFS:
+
+counteridfpd
+	RW - shows the counter number selected for the FPD Flexnoc.
+
+counterfpd_rdreq
+	RO - shows the read request count for the FPD counters.
+
+counterfpdsrc
+	WO - sets the source of the FPD counter.
+
+counterfpd_wrrsp
+	RO - shows the write response count for the FPD counters.
+
+counterfpd_rdrsp
+	RO - shows the read response count for the FPD counters.
+
+counterfpd_wrreq
+	RO - shows the write request count for the FPD counters.
+
+counterfpdport
+	WO - sets the port number selected for the FPD Flexnoc.
+
+counteridlpd
+	RW - shows the counter number selected for the LPD Flexnoc.
+
+counterlpdport
+	WO - sets the port number selected for the LPD Flexnoc.
+
+counterlpd_rdreq
+	RO - shows the read request count for the LPD counters.
+
+counterlpd_wrreq
+	RO - shows the write request count for the LPD counters.
+
+counterlpd_wrrsp
+	RO - shows the write response count for the LPD counters.
+
+counterlpdsrc
+	WO - sets the source of the LPD counter.
+
+counterlpd_rdrsp
+	RO - shows the read response count for the LPD counters.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/misc-devices/xilinx_trafgen.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/misc-devices/xilinx_trafgen.txt
@@ -0,0 +1,97 @@
+Kernel driver xilinx_trafgen
+============================
+
+Supported chips:
+Zynq SOC, Xilinx 7 series fpga's (Virtex,Kintex,Artix)
+
+Data Sheet:
+	http://www.xilinx.com/support/documentation/ip_documentation/axi_traffic_gen/v2_0/pg125-axi-traffic-gen.pdf
+
+Author:
+        Kedareswara Rao Appana <appanad@xilinx.com>
+
+Description
+-----------
+
+AXI Traffic Generator IP is a core that stresses the AXI4 interconnect and other
+AXI4 peripherals in the system. It generates a wide variety of AXI4 transactions
+based on the core programming.
+
+Features:
+---> Configurable option to generate and accept data according to different
+traffic profiles.
+---> Supports dependent/independent transaction between read/write master port
+with configurable delays.
+---> Programmable repeat count for each transaction with
+constant/increment/random address.
+---> External start/stop to generate traffic without processor intervention.
+---> Generates IP-specific traffic on AXI interface for pre-defined protocols.
+
+SYSFS:
+
+id
+	RO - shows the trafgen id.
+
+resource
+	RO - shows the baseaddress for the trafgen.
+
+master_start_stop
+	RW - monitors the master start logic.
+
+config_slave_status
+	RW - configure and monitors the slave status.
+
+err_sts
+	RW - get the error statistics/clear the errors.
+
+err_en
+	WO - enable the errors.
+
+intr_en
+	WO - enable the interrupts.
+
+last_valid_index
+	RW - gets the last valid index value.
+
+config_sts_show
+	RO - show the config status value.
+
+mram_clear
+	WO - clears the master ram.
+
+cram_clear
+	WO - clears the command ram.
+
+pram_clear
+	WO - clears the parameter ram.
+
+static_enable
+	RO - enables the static mode.
+
+static_burst_len
+	RW - gets/sets the static burst length.
+
+static_transferdone
+	RW - monitors the static transfer done status.
+
+reset_static_transferdone
+	RO - resets the static transferdone bit.
+
+stream_cfg
+	RW - sets the stream configuration parameters like delay.
+
+stream_tktsn
+	RW - TSTRB/TKEEP value for the last beat of the
+transfer set n. N can be 1 to 4.
+
+stream_enable
+	RO - enables the streaming mode.
+
+stream_transferlen
+	RW - get/set the streaming mode transfer length.
+
+stream_transfercnt
+	RW - get/set the streaming mode transfer count.
+
+loop_enable
+	RW - get/set loop enable value.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/af_xdp.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/af_xdp.rst
@@ -433,6 +433,15 @@
 application to use. The final option is the flags field, but it will
 be dealt with in separate sections for each UMEM flag.
 
+SO_BINDTODEVICE setsockopt
+--------------------------
+
+This is a generic SOL_SOCKET option that can be used to tie AF_XDP
+socket to a particular network interface.  It is useful when a socket
+is created by a privileged process and passed to a non-privileged one.
+Once the option is set, kernel will refuse attempts to bind that socket
+to a different interface.  Updating the value requires CAP_NET_RAW.
+
 XDP_STATISTICS getsockopt
 -------------------------
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/bonding.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/bonding.rst
@@ -196,11 +196,12 @@
 ad_actor_system
 
 	In an AD system, this specifies the mac-address for the actor in
-	protocol packet exchanges (LACPDUs). The value cannot be NULL or
-	multicast. It is preferred to have the local-admin bit set for this
-	mac but driver does not enforce it. If the value is not given then
-	system defaults to using the masters' mac address as actors' system
-	address.
+	protocol packet exchanges (LACPDUs). The value cannot be a multicast
+	address. If the all-zeroes MAC is specified, bonding will internally
+	use the MAC of the bond itself. It is preferred to have the
+	local-admin bit set for this mac but driver does not enforce it. If
+	the value is not given then system defaults to using the masters'
+	mac address as actors' system address.
 
 	This parameter has effect only in 802.3ad mode and is available through
 	SysFs interface.
@@ -421,6 +422,17 @@
 		consider the slave up only when all of the arp_ip_targets
 		are reachable
 
+arp_missed_max
+
+	Specifies the number of arp_interval monitor checks that must
+	fail in order for an interface to be marked down by the ARP monitor.
+
+	In order to provide orderly failover semantics, backup interfaces
+	are permitted an extra monitor check (i.e., they must fail
+	arp_missed_max + 1 times before being marked down).
+
+	The default value is 2, and the allowable range is 1 - 255.
+
 downdelay
 
 	Specifies the time, in milliseconds, to wait before disabling
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/device_drivers/ethernet/amazon/ena.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/device_drivers/ethernet/amazon/ena.rst
@@ -205,6 +205,7 @@
 More information about Adaptive Interrupt Moderation (DIM) can be found in
 Documentation/networking/net_dim.rst
 
+.. _`RX copybreak`:
 RX copybreak
 ============
 The rx_copybreak is initialized by default to ENA_DEFAULT_RX_COPYBREAK
@@ -315,3 +316,34 @@
 - The new SKB is updated with the necessary information (protocol,
   checksum hw verify result, etc), and then passed to the network
   stack, using the NAPI interface function :code:`napi_gro_receive()`.
+
+Dynamic RX Buffers (DRB)
+------------------------
+
+Each RX descriptor in the RX ring is a single memory page (which is either 4KB
+or 16KB long depending on system's configurations).
+To reduce the memory allocations required when dealing with a high rate of small
+packets, the driver tries to reuse the remaining RX descriptor's space if more
+than 2KB of this page remain unused.
+
+A simple example of this mechanism is the following sequence of events:
+
+::
+
+        1. Driver allocates page-sized RX buffer and passes it to hardware
+                +----------------------+
+                |4KB RX Buffer         |
+                +----------------------+
+
+        2. A 300Bytes packet is received on this buffer
+
+        3. The driver increases the ref count on this page and returns it back to
+           HW as an RX buffer of size 4KB - 300Bytes = 3796 Bytes
+               +----+--------------------+
+               |****|3796 Bytes RX Buffer|
+               +----+--------------------+
+
+This mechanism isn't used when an XDP program is loaded, or when the
+RX packet is less than rx_copybreak bytes (in which case the packet is
+copied out of the RX buffer into the linear part of a new skb allocated
+for it and the RX buffer remains the same size, see `RX copybreak`_).
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/device_drivers/ethernet/intel/ixgbe.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/device_drivers/ethernet/intel/ixgbe.rst
@@ -440,6 +440,22 @@
 a virtual function (VF), jumbo frames must first be enabled in the physical
 function (PF). The VF MTU setting cannot be larger than the PF MTU.
 
+NBASE-T Support
+---------------
+The ixgbe driver supports NBASE-T on some devices. However, the advertisement
+of NBASE-T speeds is suppressed by default, to accommodate broken network
+switches which cannot cope with advertised NBASE-T speeds. Use the ethtool
+command to enable advertising NBASE-T speeds on devices which support it::
+
+  ethtool -s eth? advertise 0x1800000001028
+
+On Linux systems with INTERFACES(5), this can be specified as a pre-up command
+in /etc/network/interfaces so that the interface is always brought up with
+NBASE-T support, e.g.::
+
+  iface eth? inet dhcp
+       pre-up ethtool -s eth? advertise 0x1800000001028 || true
+
 Generic Receive Offload, aka GRO
 --------------------------------
 The driver supports the in-kernel software implementation of GRO. GRO has
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/ethtool-netlink.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/ethtool-netlink.rst
@@ -213,7 +213,9 @@
   ``ETHTOOL_MSG_MODULE_EEPROM_GET``     read SFP module EEPROM
   ``ETHTOOL_MSG_STATS_GET``             get standard statistics
   ``ETHTOOL_MSG_PHC_VCLOCKS_GET``       get PHC virtual clocks info
-  ===================================== ================================
+  ``ETHTOOL_MSG_MM_GET``                get MAC merge layer state
+  ``ETHTOOL_MSG_MM_SET``                set MAC merge layer parameters
+  ===================================== =================================
 
 Kernel to userspace:
 
@@ -252,6 +254,7 @@
   ``ETHTOOL_MSG_MODULE_EEPROM_GET_REPLY``  read SFP module EEPROM
   ``ETHTOOL_MSG_STATS_GET_REPLY``          standard statistics
   ``ETHTOOL_MSG_PHC_VCLOCKS_GET_REPLY``    PHC virtual clocks info
+  ``ETHTOOL_MSG_MM_GET_REPLY``             MAC merge layer status
   ======================================== =================================
 
 ``GET`` requests are sent by userspace applications to retrieve device
@@ -1017,8 +1020,18 @@
 
   =====================================  ======  ==========================
   ``ETHTOOL_A_PAUSE_HEADER``             nested  request header
+  ``ETHTOOL_A_PAUSE_STATS_SRC``          u32     source of statistics
   =====================================  ======  ==========================
 
+``ETHTOOL_A_PAUSE_STATS_SRC`` is optional. It takes values from:
+
+.. kernel-doc:: include/uapi/linux/ethtool.h
+    :identifiers: ethtool_mac_stats_src
+
+If absent from the request, stats will be provided with
+an ``ETHTOOL_A_PAUSE_STATS_SRC`` attribute in the response equal to
+``ETHTOOL_MAC_STATS_SRC_AGGREGATE``.
+
 Kernel response contents:
 
   =====================================  ======  ==========================
@@ -1433,6 +1446,7 @@
 
   =======================================  ======  ==========================
   ``ETHTOOL_A_STATS_HEADER``               nested  request header
+  ``ETHTOOL_A_STATS_SRC``                  u32     source of statistics
   ``ETHTOOL_A_STATS_GROUPS``               bitset  requested groups of stats
   =======================================  ======  ==========================
 
@@ -1441,6 +1455,8 @@
  +-----------------------------------+--------+--------------------------------+
  | ``ETHTOOL_A_STATS_HEADER``        | nested | reply header                   |
  +-----------------------------------+--------+--------------------------------+
+ | ``ETHTOOL_A_STATS_SRC``           | u32    | source of statistics           |
+ +-----------------------------------+--------+--------------------------------+
  | ``ETHTOOL_A_STATS_GRP``           | nested | one or more group of stats     |
  +-+---------------------------------+--------+--------------------------------+
  | | ``ETHTOOL_A_STATS_GRP_ID``      | u32    | group ID - ``ETHTOOL_STATS_*`` |
@@ -1502,6 +1518,11 @@
  etherStatsPkts512to1023Octets 512  1023
  ============================= ==== ====
 
+``ETHTOOL_A_STATS_SRC`` is optional. Similar to ``PAUSE_GET``, it takes values
+from ``enum ethtool_mac_stats_src``. If absent from the request, stats will be
+provided with an ``ETHTOOL_A_STATS_SRC`` attribute in the response equal to
+``ETHTOOL_MAC_STATS_SRC_AGGREGATE``.
+
 PHC_VCLOCKS_GET
 ===============
 
@@ -1521,6 +1542,90 @@
   ``ETHTOOL_A_PHC_VCLOCKS_INDEX``       s32     PHC index array
   ====================================  ======  ==========================
 
+MM_GET
+======
+
+Retrieve 802.3 MAC Merge parameters.
+
+Request contents:
+
+  ====================================  ======  ==========================
+  ``ETHTOOL_A_MM_HEADER``               nested  request header
+  ====================================  ======  ==========================
+
+Kernel response contents:
+
+  =================================  ======  ===================================
+  ``ETHTOOL_A_MM_HEADER``            nested  request header
+  ``ETHTOOL_A_MM_PMAC_ENABLED``      bool    set if RX of preemptible and SMD-V
+                                             frames is enabled
+  ``ETHTOOL_A_MM_TX_ENABLED``        bool    set if TX of preemptible frames is
+                                             administratively enabled (might be
+                                             inactive if verification failed)
+  ``ETHTOOL_A_MM_TX_ACTIVE``         bool    set if TX of preemptible frames is
+                                             operationally enabled
+  ``ETHTOOL_A_MM_TX_MIN_FRAG_SIZE``  u32     minimum size of transmitted
+                                             non-final fragments, in octets
+  ``ETHTOOL_A_MM_RX_MIN_FRAG_SIZE``  u32     minimum size of received non-final
+                                             fragments, in octets
+  ``ETHTOOL_A_MM_VERIFY_ENABLED``    bool    set if TX of SMD-V frames is
+                                             administratively enabled
+  ``ETHTOOL_A_MM_VERIFY_STATUS``     u8      state of the verification function
+  ``ETHTOOL_A_MM_VERIFY_TIME``       u32     delay between verification attempts
+  ``ETHTOOL_A_MM_MAX_VERIFY_TIME```  u32     maximum verification interval
+                                             supported by device
+  ``ETHTOOL_A_MM_STATS``             nested  IEEE 802.3-2018 subclause 30.14.1
+                                             oMACMergeEntity statistics counters
+  =================================  ======  ===================================
+
+The attributes are populated by the device driver through the following
+structure:
+
+.. kernel-doc:: include/linux/ethtool.h
+    :identifiers: ethtool_mm_state
+
+The ``ETHTOOL_A_MM_VERIFY_STATUS`` will report one of the values from
+
+.. kernel-doc:: include/uapi/linux/ethtool.h
+    :identifiers: ethtool_mm_verify_status
+
+If ``ETHTOOL_A_MM_VERIFY_ENABLED`` was passed as false in the ``MM_SET``
+command, ``ETHTOOL_A_MM_VERIFY_STATUS`` will report either
+``ETHTOOL_MM_VERIFY_STATUS_INITIAL`` or ``ETHTOOL_MM_VERIFY_STATUS_DISABLED``,
+otherwise it should report one of the other states.
+
+It is recommended that drivers start with the pMAC disabled, and enable it upon
+user space request. It is also recommended that user space does not depend upon
+the default values from ``ETHTOOL_MSG_MM_GET`` requests.
+
+``ETHTOOL_A_MM_STATS`` are reported if ``ETHTOOL_FLAG_STATS`` was set in
+``ETHTOOL_A_HEADER_FLAGS``. The attribute will be empty if driver did not
+report any statistics. Drivers fill in the statistics in the following
+structure:
+
+.. kernel-doc:: include/linux/ethtool.h
+    :identifiers: ethtool_mm_stats
+
+MM_SET
+======
+
+Modifies the configuration of the 802.3 MAC Merge layer.
+
+Request contents:
+
+  =================================  ======  ==========================
+  ``ETHTOOL_A_MM_VERIFY_TIME``       u32     see MM_GET description
+  ``ETHTOOL_A_MM_VERIFY_ENABLED``    bool    see MM_GET description
+  ``ETHTOOL_A_MM_TX_ENABLED``        bool    see MM_GET description
+  ``ETHTOOL_A_MM_PMAC_ENABLED``      bool    see MM_GET description
+  ``ETHTOOL_A_MM_TX_MIN_FRAG_SIZE``  u32     see MM_GET description
+  =================================  ======  ==========================
+
+The attributes are propagated to the driver through the following structure:
+
+.. kernel-doc:: include/linux/ethtool.h
+    :identifiers: ethtool_mm_cfg
+
 Request translation
 ===================
 
@@ -1620,4 +1725,6 @@
   n/a                                 ``ETHTOOL_MSG_CABLE_TEST_TDR_ACT``
   n/a                                 ``ETHTOOL_MSG_TUNNEL_INFO_GET``
   n/a                                 ``ETHTOOL_MSG_PHC_VCLOCKS_GET``
+  n/a                                 ``ETHTOOL_MSG_MM_GET``
+  n/a                                 ``ETHTOOL_MSG_MM_SET``
   =================================== =====================================
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/index.rst
@@ -46,7 +46,6 @@
    cdc_mbim
    dccp
    dctcp
-   decnet
    dns_resolver
    driver
    eql
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/ip-sysctl.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/ip-sysctl.rst
@@ -322,6 +322,8 @@
 	Reserve max(window/2^tcp_app_win, mss) of window for application
 	buffer. Value 0 is special, it means that nothing is reserved.
 
+	Possible values are [0, 31], inclusive.
+
 	Default: 31
 
 tcp_autocorking - BOOLEAN
@@ -1063,7 +1065,7 @@
 cipso_cache_bucket_size - INTEGER
 	The CIPSO label cache consists of a fixed size hash table with each
 	hash bucket containing a number of cache entries.  This variable limits
-	the number of entries in each hash bucket; the larger the value the
+	the number of entries in each hash bucket; the larger the value is, the
 	more CIPSO label mappings that can be cached.  When the number of
 	entries in a given hash bucket reaches this limit adding new entries
 	causes the oldest entry in the bucket to be removed to make room.
@@ -1157,7 +1159,7 @@
 	option should only be set by experts.
 	Default: 0
 
-ip_dynaddr - BOOLEAN
+ip_dynaddr - INTEGER
 	If set non-zero, enables support for dynamic addresses.
 	If set to a non-zero value larger than 1, a kernel log
 	message will be printed when dynamic address rewriting
@@ -2068,6 +2070,14 @@
 
 	Default: 1
 
+accept_ra_min_lft - INTEGER
+	Minimum acceptable lifetime value in Router Advertisement.
+
+	RA sections with a lifetime less than this value shall be
+	ignored. Zero lifetimes stay unaffected.
+
+	Default: 0
+
 accept_ra_pinfo - BOOLEAN
 	Learn Prefix Information in Router Advertisement.
 
@@ -2808,7 +2818,14 @@
 	Default: 4K
 
 sctp_wmem  - vector of 3 INTEGERs: min, default, max
-	Currently this tunable has no effect.
+	Only the first value ("min") is used, "default" and "max" are
+	ignored.
+
+	min: Minimum size of send buffer that can be used by SCTP sockets.
+	It is guaranteed to each SCTP socket (but not association) even
+	under moderate memory pressure.
+
+	Default: 4K
 
 addr_scope_policy - INTEGER
 	Control IPv4 address scoping - draft-stewart-tsvwg-sctp-ipv4-00
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/ipvs-sysctl.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/ipvs-sysctl.rst
@@ -37,8 +37,7 @@
 
 	0: disable any special handling on port reuse. The new
 	connection will be delivered to the same real server that was
-	servicing the previous connection. This will effectively
-	disable expire_nodest_conn.
+	servicing the previous connection.
 
 	bit 1: enable rescheduling of new connections when it is safe.
 	That is, whenever expire_nodest_conn and for TCP sockets, when
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/j1939.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/j1939.rst
@@ -121,7 +121,7 @@
 
 On the other hand, when using PDU1 format, the PS-field contains a so-called
 Destination Address, which is _not_ part of the PGN. When communicating a PGN
-from user space to kernel (or vice versa) and PDU2 format is used, the PS-field
+from user space to kernel (or vice versa) and PDU1 format is used, the PS-field
 of the PGN shall be set to zero. The Destination Address shall be set
 elsewhere.
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/networking/statistics.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/networking/statistics.rst
@@ -171,6 +171,7 @@
 
   - `ETHTOOL_MSG_PAUSE_GET`
   - `ETHTOOL_MSG_FEC_GET`
+  - `ETHTOOL_MSG_MM_GET`
 
 debugfs
 -------
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/power/runtime_pm.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/power/runtime_pm.rst
@@ -341,7 +341,9 @@
 
   `int pm_runtime_resume_and_get(struct device *dev);`
     - run pm_runtime_resume(dev) and if successful, increment the device's
-      usage counter; return the result of pm_runtime_resume
+      usage counter; returns 0 on success (whether or not the device's
+      runtime PM status was already 'active') or the error code from
+      pm_runtime_resume() on failure.
 
   `int pm_request_idle(struct device *dev);`
     - submit a request to execute the subsystem-level idle callback for the
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/process/code-of-conduct-interpretation.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/process/code-of-conduct-interpretation.rst
@@ -51,7 +51,7 @@
 uncertain how to handle situations that come up.  It will not be
 considered a violation report unless you want it to be.  If you are
 uncertain about approaching the TAB or any other maintainers, please
-reach out to our conflict mediator, Mishi Choudhary <mishi@linux.com>.
+reach out to our conflict mediator, Joanna Lee <jlee@linuxfoundation.org>.
 
 In the end, "be kind to each other" is really what the end goal is for
 everybody.  We know everyone is human and we all fail at times, but the
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/process/deprecated.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/process/deprecated.rst
@@ -70,6 +70,9 @@
 
 	foo = kmalloc_array(count, size, GFP_KERNEL);
 
+Specifically, kmalloc() can be replaced with kmalloc_array(), and
+kzalloc() can be replaced with kcalloc().
+
 If no 2-factor form is available, the saturate-on-overflow helpers should
 be used::
 
@@ -90,9 +93,20 @@
         array usage and switch to a `flexible array member
         <#zero-length-and-one-element-arrays>`_ instead.
 
-See array_size(), array3_size(), and struct_size(),
-for more details as well as the related check_add_overflow() and
-check_mul_overflow() family of functions.
+For other calculations, please compose the use of the size_mul(),
+size_add(), and size_sub() helpers. For example, in the case of::
+
+	foo = krealloc(current_size + chunk_size * (count - 3), GFP_KERNEL);
+
+Instead, use the helpers::
+
+	foo = krealloc(size_add(current_size,
+				size_mul(chunk_size,
+					 size_sub(count, 3))), GFP_KERNEL);
+
+For more details, also see array3_size() and flex_array_size(),
+as well as the related check_mul_overflow(), check_add_overflow(),
+check_sub_overflow(), and check_shl_overflow() family of functions.
 
 simple_strtol(), simple_strtoll(), simple_strtoul(), simple_strtoull()
 ----------------------------------------------------------------------
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/process/howto.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/process/howto.rst
@@ -36,7 +36,7 @@
  - "C:  A Reference Manual" by Harbison and Steele [Prentice Hall]
 
 The kernel is written using GNU C and the GNU toolchain.  While it
-adheres to the ISO C89 standard, it uses a number of extensions that are
+adheres to the ISO C11 standard, it uses a number of extensions that are
 not featured in the standard.  The kernel is a freestanding C
 environment, with no reliance on the standard C library, so some
 portions of the C standard are not supported.  Arbitrary long long
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/process/stable-kernel-rules.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/process/stable-kernel-rules.rst
@@ -168,7 +168,16 @@
  - The finalized and tagged releases of all stable kernels can be found
    in separate branches per version at:
 
-	https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git
+	https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
+
+ - The release candidate of all stable kernel versions can be found at:
+
+        https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git/
+
+   .. warning::
+      The -stable-rc tree is a snapshot in time of the stable-queue tree and
+      will change frequently, hence will be rebased often. It should only be
+      used for testing purposes (e.g. to be consumed by CI systems).
 
 
 Review committee
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/process/submitting-patches.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/process/submitting-patches.rst
@@ -72,7 +72,7 @@
 
 The maintainer will thank you if you write your patch description in a
 form which can be easily pulled into Linux's source code management
-system, ``git``, as a "commit log".  See :ref:`explicit_in_reply_to`.
+system, ``git``, as a "commit log".  See :ref:`the_canonical_patch_format`.
 
 Solve only one problem per patch.  If your description starts to get
 long, that's a sign that you probably need to split up your patch.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/riscv/vm-layout.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/riscv/vm-layout.rst
@@ -48,7 +48,7 @@
   ____________________________________________________________|___________________________________________________________
                     |            |                  |         |
    ffffffc000000000 | -256    GB | ffffffc7ffffffff |   32 GB | kasan
-   ffffffcefee00000 | -196    GB | ffffffcefeffffff |    2 MB | fixmap
+   ffffffcefea00000 | -196    GB | ffffffcefeffffff |    6 MB | fixmap
    ffffffceff000000 | -196    GB | ffffffceffffffff |   16 MB | PCI io
    ffffffcf00000000 | -196    GB | ffffffcfffffffff |    4 GB | vmemmap
    ffffffd000000000 | -192    GB | ffffffdfffffffff |   64 GB | vmalloc/ioremap space
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/scsi/scsi_mid_low_api.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/scsi/scsi_mid_low_api.rst
@@ -1190,11 +1190,11 @@
 		 - pointer to scsi_device object that this command is
                    associated with.
     resid
-		 - an LLD should set this signed integer to the requested
+		 - an LLD should set this unsigned integer to the requested
                    transfer length (i.e. 'request_bufflen') less the number
                    of bytes that are actually transferred. 'resid' is
                    preset to 0 so an LLD can ignore it if it cannot detect
-                   underruns (overruns should be rare). If possible an LLD
+                   underruns (overruns should not be reported). An LLD
                    should set 'resid' prior to invoking 'done'. The most
                    interesting case is data transfers from a SCSI target
                    device (e.g. READs) that underrun.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/security/keys/trusted-encrypted.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/security/keys/trusted-encrypted.rst
@@ -87,22 +87,26 @@
 Trusted Keys
 ------------
 
-New keys are created from random numbers generated in the trust source. They
-are encrypted/decrypted using a child key in the storage key hierarchy.
-Encryption and decryption of the child key must be protected by a strong
-access control policy within the trust source.
+New keys are created from random numbers. They are encrypted/decrypted using
+a child key in the storage key hierarchy. Encryption and decryption of the
+child key must be protected by a strong access control policy within the
+trust source. The random number generator in use differs according to the
+selected trust source:
 
-  *  TPM (hardware device) based RNG
+  *  TPM: hardware device based RNG
 
-     Strength of random numbers may vary from one device manufacturer to
-     another.
+     Keys are generated within the TPM. Strength of random numbers may vary
+     from one device manufacturer to another.
 
-  *  TEE (OP-TEE based on Arm TrustZone) based RNG
+  *  TEE: OP-TEE based on Arm TrustZone based RNG
 
      RNG is customizable as per platform needs. It can either be direct output
      from platform specific hardware RNG or a software based Fortuna CSPRNG
      which can be seeded via multiple entropy sources.
 
+Users may override this by specifying ``trusted.rng=kernel`` on the kernel
+command-line to override the used RNG with the kernel's random number pool.
+
 Encrypted Keys
 --------------
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/security/lsm.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/security/lsm.rst
@@ -129,3 +129,31 @@
 The capabilities security module does not use the general security
 blobs, unlike other modules. The reasons are historical and are
 based on overhead, complexity and performance concerns.
+
+LSM External Interfaces
+=======================
+
+The LSM infrastructure does not generally provide external interfaces.
+The individual security modules provide what external interfaces they
+require.
+
+The file ``/sys/kernel/security/lsm`` provides a comma
+separated list of the active security modules.
+
+The file ``/proc/pid/attr/display`` contains the name of the security
+module for which the ``/proc/pid/attr/current`` interface will
+apply. This interface can be written to.
+
+The infrastructure does provide an interface for the special
+case where multiple security modules provide a process context.
+This is provided in compound context format.
+
+-  `lsm\0value\0lsm\0value\0`
+
+The `lsm` and `value` fields are nul terminated bytestrings.
+Each field may contain whitespace or non-printable characters.
+The nul bytes are included in the size of a compound context.
+The context ``Bell\0Secret\0Biba\0Loose\0`` has a size of 23.
+
+The file ``/proc/pid/attr/context`` provides the security
+context of the identified process.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sound/alsa-configuration.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sound/alsa-configuration.rst
@@ -2237,7 +2237,7 @@
     Apply the generic implicit feedback sync mode.  When this is set
     and the playback stream sync mode is ASYNC, the driver tries to
     tie an adjacent ASYNC capture stream as the implicit feedback
-    source.
+    source.  This is equivalent with quirk_flags bit 17.
 use_vmalloc
     Use vmalloc() for allocations of the PCM buffers (default: yes).
     For architectures with non-coherent memory like ARM or MIPS, the
@@ -2279,6 +2279,8 @@
         * bit 14: Ignore errors for mixer access
         * bit 15: Support generic DSD raw U32_BE format
         * bit 16: Set up the interface at first like UAC1
+        * bit 17: Apply the generic implicit feedback sync mode
+        * bit 18: Don't apply implicit feedback sync mode
 
 This module supports multiple devices, autoprobe and hotplugging.
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sound/hd-audio/models.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sound/hd-audio/models.rst
@@ -261,6 +261,10 @@
 huawei-mbx-stereo
     Enable initialization verbs for Huawei MBX stereo speakers;
     might be risky, try this at your own risk
+alc298-samsung-headphone
+    Samsung laptops with ALC298
+alc256-samsung-headphone
+    Samsung laptops with ALC256
 
 ALC66x/67x/892
 ==============
@@ -326,6 +330,8 @@
     Headset support on USI machines
 dual-codecs
     Lenovo laptops with dual codecs
+alc285-hp-amp-init
+    HP laptops which require speaker amplifier initialization (ALC285)
 
 ALC680
 ======
@@ -698,7 +704,7 @@
 no-jd
     BIOS setup but without jack-detection
 intel
-    Intel DG45* mobos
+    Intel D*45* mobos
 dell-m6-amic
     Dell desktops/laptops with analog mics
 dell-m6-dmic
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sound/soc/dapm.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sound/soc/dapm.rst
@@ -234,7 +234,7 @@
 a virtual widget - a widget with no control bits e.g.
 ::
 
-  SND_SOC_DAPM_MIXER("AC97 Mixer", SND_SOC_DAPM_NOPM, 0, 0, NULL, 0),
+  SND_SOC_DAPM_MIXER("AC97 Mixer", SND_SOC_NOPM, 0, 0, NULL, 0),
 
 This can be used to merge to signal paths together in software.
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sphinx/cdomain.py
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sphinx/cdomain.py
@@ -37,12 +37,29 @@
 
 import sphinx
 from sphinx import addnodes
-from sphinx.domains.c import c_funcptr_sig_re, c_sig_re
 from sphinx.domains.c import CObject as Base_CObject
 from sphinx.domains.c import CDomain as Base_CDomain
 from itertools import chain
 import re
 
+# fixes https://github.com/sphinx-doc/sphinx/commit/0f49e30c51b5cc5055cda5b4b294c2dd9d1df573#r38750737
+
+# pylint: disable=invalid-name
+c_sig_re = re.compile(
+    r'''^([^(]*?)          # return type
+        ([\w:.]+)  \s*     # thing name (colon allowed for C++)
+        (?: \((.*)\) )?    # optionally arguments
+        (\s+const)? $      # const specifier
+    ''', re.VERBOSE)
+
+c_funcptr_sig_re = re.compile(
+    r'''^([^(]+?)          # return type
+        (\( [^()]+ \)) \s* # name in parentheses
+        \( (.*) \)         # arguments
+        (\s+const)? $      # const specifier
+    ''', re.VERBOSE)
+# pylint: enable=invalid-name
+
 __version__  = '1.1'
 
 # Get Sphinx version
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sphinx/kernel_include.py
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sphinx/kernel_include.py
@@ -94,7 +94,6 @@
         # HINT: this is the only line I had to change / commented out:
         #path = utils.relative_path(None, path)
 
-        path = nodes.reprunicode(path)
         encoding = self.options.get(
             'encoding', self.state.document.settings.input_encoding)
         e_handler=self.state.document.settings.input_encoding_error_handler
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sphinx/load_config.py
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sphinx/load_config.py
@@ -3,7 +3,7 @@
 
 import os
 import sys
-from sphinx.util.pycompat import execfile_
+from sphinx.util.osutil import fs_encoding
 
 # ------------------------------------------------------------------------------
 def loadConfig(namespace):
@@ -48,7 +48,9 @@
             sys.stdout.write("load additional sphinx-config: %s\n" % config_file)
             config = namespace.copy()
             config['__file__'] = config_file
-            execfile_(config_file, config)
+            with open(config_file, 'rb') as f:
+                code = compile(f.read(), fs_encoding, 'exec')
+                exec(code, config)
             del config['__file__']
             namespace.update(config)
         else:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/sphinx/requirements.txt
+++ linux-xilinx-zynqmp-5.15.0/Documentation/sphinx/requirements.txt
@@ -1,2 +1,4 @@
+# jinja2>=3.1 is not compatible with Sphinx<4.0
+jinja2<3.1
 sphinx_rtd_theme
 Sphinx==2.4.4
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/timers/no_hz.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/timers/no_hz.rst
@@ -129,11 +129,8 @@
 online to handle timekeeping tasks in order to ensure that system
 calls like gettimeofday() returns accurate values on adaptive-tick CPUs.
 (This is not an issue for CONFIG_NO_HZ_IDLE=y because there are no running
-user processes to observe slight drifts in clock rate.)  Therefore, the
-boot CPU is prohibited from entering adaptive-ticks mode.  Specifying a
-"nohz_full=" mask that includes the boot CPU will result in a boot-time
-error message, and the boot CPU will be removed from the mask.  Note that
-this means that your system must have at least two CPUs in order for
+user processes to observe slight drifts in clock rate.) Note that this
+means that your system must have at least two CPUs in order for
 CONFIG_NO_HZ_FULL=y to do anything for you.
 
 Finally, adaptive-ticks CPUs must have their RCU callbacks offloaded.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/trace/coresight/coresight-config.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/trace/coresight/coresight-config.rst
@@ -211,19 +211,13 @@
 be selected when running trace under perf::
 
     $ ls /sys/devices/cs_etm
-    configurations  format  perf_event_mux_interval_ms  sinks  type
-    events  nr_addr_filters  power
+    cpu0  cpu2  events  nr_addr_filters		power  subsystem  uevent
+    cpu1  cpu3  format  perf_event_mux_interval_ms	sinks  type
 
-Key directories here are 'configurations' - which lists the loaded
-configurations, and 'events' - a generic perf directory which allows
-selection on the perf command line.::
+The key directory here is 'events' - a generic perf directory which allows
+selection on the perf command line. As with the sinks entries, this provides
+a hash of the configuration name.
 
-    $ ls configurations/
-    autofdo
-    $ cat configurations/autofdo
-    0xa7c3dddd
-
-As with the sinks entries, this provides a hash of the configuration name.
 The entry in the 'events' directory uses perfs built in syntax generator
 to substitute the syntax for the name when evaluating the command::
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/trace/events.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/trace/events.rst
@@ -198,6 +198,15 @@
   prev_comm ~ "*sh*"
   prev_comm ~ "ba*sh"
 
+If the field is a pointer that points into user space (for example
+"filename" from sys_enter_openat), then you have to append ".ustring" to the
+field name::
+
+  filename.ustring ~ "password"
+
+As the kernel will have to know how to retrieve the memory that the pointer
+is at from user space.
+
 5.2 Setting filters
 -------------------
 
@@ -230,6 +239,16 @@
 the filter string; the error message should still be useful though
 even without more accurate position info.
 
+5.2.1 Filter limitations
+------------------------
+
+If a filter is placed on a string pointer ``(char *)`` that does not point
+to a string on the ring buffer, but instead points to kernel or user space
+memory, then, for safety reasons, at most 1024 bytes of the content is
+copied onto a temporary buffer to do the compare. If the copy of the memory
+faults (the pointer points to memory that should not be accessed), then the
+string compare will be treated as not matching.
+
 5.3 Clearing filters
 --------------------
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/trace/ftrace.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/trace/ftrace.rst
@@ -2929,7 +2929,7 @@
               bash-1994  [000] ....  4342.324898: ima_get_action <-process_measurement
               bash-1994  [000] ....  4342.324898: ima_match_policy <-ima_get_action
               bash-1994  [000] ....  4342.324899: do_truncate <-do_last
-              bash-1994  [000] ....  4342.324899: should_remove_suid <-do_truncate
+              bash-1994  [000] ....  4342.324899: setattr_should_drop_suidgid <-do_truncate
               bash-1994  [000] ....  4342.324899: notify_change <-do_truncate
               bash-1994  [000] ....  4342.324900: current_fs_time <-notify_change
               bash-1994  [000] ....  4342.324900: current_kernel_time <-current_fs_time
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/trace/histogram.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/trace/histogram.rst
@@ -39,7 +39,7 @@
   will use the event's kernel stacktrace as the key.  The keywords
   'keys' or 'key' can be used to specify keys, and the keywords
   'values', 'vals', or 'val' can be used to specify values.  Compound
-  keys consisting of up to two fields can be specified by the 'keys'
+  keys consisting of up to three fields can be specified by the 'keys'
   keyword.  Hashing a compound key produces a unique entry in the
   table for each unique combination of component keys, and can be
   useful for providing more fine-grained summaries of event data.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/trace/kprobetrace.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/trace/kprobetrace.rst
@@ -58,8 +58,8 @@
   NAME=FETCHARG : Set NAME as the argument name of FETCHARG.
   FETCHARG:TYPE : Set TYPE as the type of FETCHARG. Currently, basic types
 		  (u8/u16/u32/u64/s8/s16/s32/s64), hexadecimal types
-		  (x8/x16/x32/x64), "string", "ustring" and bitfield
-		  are supported.
+		  (x8/x16/x32/x64), "string", "ustring", "symbol", "symstr"
+                  and bitfield are supported.
 
   (\*1) only for the probe on function entry (offs == 0).
   (\*2) only for return probe.
@@ -96,6 +96,10 @@
 
 Symbol type('symbol') is an alias of u32 or u64 type (depends on BITS_PER_LONG)
 which shows given pointer in "symbol+offset" style.
+On the other hand, symbol-string type ('symstr') converts the given address to
+"symbol+offset/symbolsize" style and stores it as a null-terminated string.
+With 'symstr' type, you can filter the event with wildcard pattern of the
+symbols, and you don't need to solve symbol name by yourself.
 For $comm, the default type is "string"; any other type is invalid.
 
 .. _user_mem_access:
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/translations/it_IT/kernel-hacking/locking.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/translations/it_IT/kernel-hacking/locking.rst
@@ -1396,7 +1396,7 @@
 Riferimento per l'API dei Futex
 ===============================
 
-.. kernel-doc:: kernel/futex.c
+.. kernel-doc:: kernel/futex/core.c
    :internal:
 
 Approfondimenti
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/translations/it_IT/process/howto.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/translations/it_IT/process/howto.rst
@@ -44,7 +44,7 @@
 - "C:  A Reference Manual" di Harbison and Steele [Prentice Hall]
 
 Il kernel è stato scritto usando GNU C e la toolchain GNU.
-Sebbene si attenga allo standard ISO C89, esso utilizza una serie di
+Sebbene si attenga allo standard ISO C11, esso utilizza una serie di
 estensioni che non sono previste in questo standard. Il kernel è un
 ambiente C indipendente, che non ha alcuna dipendenza dalle librerie
 C standard, così alcune parti del C standard non sono supportate.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/translations/ja_JP/howto.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/translations/ja_JP/howto.rst
@@ -65,7 +65,7 @@
  - 『新・詳説 C 言語 H&S リファレンス』 (サミュエル P ハービソン/ガイ L スティール共著 斉藤 信男監訳)[ソフトバンク]
 
 カーネルは GNU C と GNU ツールチェインを使って書かれています。カーネル
-は ISO C89 仕様に準拠して書く一方で、標準には無い言語拡張を多く使って
+は ISO C11 仕様に準拠して書く一方で、標準には無い言語拡張を多く使って
 います。カーネルは標準 C ライブラリに依存しない、C 言語非依存環境です。
 そのため、C の標準の中で使えないものもあります。特に任意の long long
 の除算や浮動小数点は使えません。カーネルがツールチェインや C 言語拡張
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/translations/ko_KR/howto.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/translations/ko_KR/howto.rst
@@ -62,7 +62,7 @@
  - "Practical C Programming" by Steve Oualline [O'Reilly]
  - "C:  A Reference Manual" by Harbison and Steele [Prentice Hall]
 
-커널은 GNU C와 GNU 툴체인을 사용하여 작성되었다. 이 툴들은 ISO C89 표준을
+커널은 GNU C와 GNU 툴체인을 사용하여 작성되었다. 이 툴들은 ISO C11 표준을
 따르는 반면 표준에 있지 않은 많은 확장기능도 가지고 있다. 커널은 표준 C
 라이브러리와는 관계없이 freestanding C 환경이어서 C 표준의 일부는
 지원되지 않는다. 임의의 long long 나누기나 floating point는 지원되지 않는다.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/translations/zh_CN/process/howto.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/translations/zh_CN/process/howto.rst
@@ -45,7 +45,7 @@
  - "C:  A Reference Manual" by Harbison and Steele [Prentice Hall]
    《C语言参考手册（原书第5版）》（邱仲潘 等译）[机械工业出版社]
 
-Linux内核使用GNU C和GNU工具链开发。虽然它遵循ISO C89标准，但也用到了一些
+Linux内核使用GNU C和GNU工具链开发。虽然它遵循ISO C11标准，但也用到了一些
 标准中没有定义的扩展。内核是自给自足的C环境，不依赖于标准C库的支持，所以
 并不支持C标准中的部分定义。比如long long类型的大数除法和浮点运算就不允许
 使用。有时候确实很难弄清楚内核对工具链的要求和它所使用的扩展，不幸的是目
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/translations/zh_TW/process/howto.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/translations/zh_TW/process/howto.rst
@@ -48,7 +48,7 @@
  - "C:  A Reference Manual" by Harbison and Steele [Prentice Hall]
    《C語言參考手冊（原書第5版）》（邱仲潘 等譯）[機械工業出版社]
 
-Linux內核使用GNU C和GNU工具鏈開發。雖然它遵循ISO C89標準，但也用到了一些
+Linux內核使用GNU C和GNU工具鏈開發。雖然它遵循ISO C11標準，但也用到了一些
 標準中沒有定義的擴展。內核是自給自足的C環境，不依賴於標準C庫的支持，所以
 並不支持C標準中的部分定義。比如long long類型的大數除法和浮點運算就不允許
 使用。有時候確實很難弄清楚內核對工具鏈的要求和它所使用的擴展，不幸的是目
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/tty/device_drivers/oxsemi-tornado.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/tty/device_drivers/oxsemi-tornado.rst
@@ -0,0 +1,129 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================================================================
+Notes on Oxford Semiconductor PCIe (Tornado) 950 serial port devices
+====================================================================
+
+Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
+by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
+
+The baud rate produced by the baud generator is obtained from this input
+frequency by dividing it by the clock prescaler, which can be set to any
+value from 1 to 63.875 in increments of 0.125, and then the usual 16-bit
+divisor is used as with the original 8250, to divide the frequency by a
+value from 1 to 65535.  Finally a programmable oversampling rate is used
+that can take any value from 4 to 16 to divide the frequency further and
+determine the actual baud rate used.  Baud rates from 15625000bps down
+to 0.933bps can be obtained this way.
+
+By default the oversampling rate is set to 16 and the clock prescaler is
+set to 33.875, meaning that the frequency to be used as the reference
+for the usual 16-bit divisor is 115313.653, which is close enough to the
+frequency of 115200 used by the original 8250 for the same values to be
+used for the divisor to obtain the requested baud rates by software that
+is unaware of the extra clock controls available.
+
+The oversampling rate is programmed with the TCR register and the clock
+prescaler is programmed with the CPR/CPR2 register pair[1][2][3][4].
+To switch away from the default value of 33.875 for the prescaler the
+the enhanced mode has to be explicitly enabled though, by setting bit 4
+of the EFR.  In that mode setting bit 7 in the MCR enables the prescaler
+or otherwise it is bypassed as if the value of 1 was used.  Additionally
+writing any value to CPR clears CPR2 for compatibility with old software
+written for older conventional PCI Oxford Semiconductor devices that do
+not have the extra prescaler's 9th bit in CPR2, so the CPR/CPR2 register
+pair has to be programmed in the right order.
+
+By using these parameters rates from 15625000bps down to 1bps can be
+obtained, with either exact or highly-accurate actual bit rates for
+standard and many non-standard rates.
+
+Here are the figures for the standard and some non-standard baud rates
+(including those quoted in Oxford Semiconductor documentation), giving
+the requested rate (r), the actual rate yielded (a) and its deviation
+from the requested rate (d), and the values of the oversampling rate
+(tcr), the clock prescaler (cpr) and the divisor (div) produced by the
+new `get_divisor' handler:
+
+r: 15625000, a: 15625000.00, d:  0.0000%, tcr:  4, cpr:  1.000, div:     1
+r: 12500000, a: 12500000.00, d:  0.0000%, tcr:  5, cpr:  1.000, div:     1
+r: 10416666, a: 10416666.67, d:  0.0000%, tcr:  6, cpr:  1.000, div:     1
+r:  8928571, a:  8928571.43, d:  0.0000%, tcr:  7, cpr:  1.000, div:     1
+r:  7812500, a:  7812500.00, d:  0.0000%, tcr:  8, cpr:  1.000, div:     1
+r:  4000000, a:  4000000.00, d:  0.0000%, tcr:  5, cpr:  3.125, div:     1
+r:  3686400, a:  3676470.59, d: -0.2694%, tcr:  8, cpr:  2.125, div:     1
+r:  3500000, a:  3496503.50, d: -0.0999%, tcr: 13, cpr:  1.375, div:     1
+r:  3000000, a:  2976190.48, d: -0.7937%, tcr: 14, cpr:  1.500, div:     1
+r:  2500000, a:  2500000.00, d:  0.0000%, tcr: 10, cpr:  2.500, div:     1
+r:  2000000, a:  2000000.00, d:  0.0000%, tcr: 10, cpr:  3.125, div:     1
+r:  1843200, a:  1838235.29, d: -0.2694%, tcr: 16, cpr:  2.125, div:     1
+r:  1500000, a:  1492537.31, d: -0.4975%, tcr:  5, cpr:  8.375, div:     1
+r:  1152000, a:  1152073.73, d:  0.0064%, tcr: 14, cpr:  3.875, div:     1
+r:   921600, a:   919117.65, d: -0.2694%, tcr: 16, cpr:  2.125, div:     2
+r:   576000, a:   576036.87, d:  0.0064%, tcr: 14, cpr:  3.875, div:     2
+r:   460800, a:   460829.49, d:  0.0064%, tcr:  7, cpr:  3.875, div:     5
+r:   230400, a:   230414.75, d:  0.0064%, tcr: 14, cpr:  3.875, div:     5
+r:   115200, a:   115207.37, d:  0.0064%, tcr: 14, cpr:  1.250, div:    31
+r:    57600, a:    57603.69, d:  0.0064%, tcr:  8, cpr:  3.875, div:    35
+r:    38400, a:    38402.46, d:  0.0064%, tcr: 14, cpr:  3.875, div:    30
+r:    19200, a:    19201.23, d:  0.0064%, tcr:  8, cpr:  3.875, div:   105
+r:     9600, a:     9600.06, d:  0.0006%, tcr:  9, cpr:  1.125, div:   643
+r:     4800, a:     4799.98, d: -0.0004%, tcr:  7, cpr:  2.875, div:   647
+r:     2400, a:     2400.02, d:  0.0008%, tcr:  9, cpr:  2.250, div:  1286
+r:     1200, a:     1200.00, d:  0.0000%, tcr: 14, cpr:  2.875, div:  1294
+r:      300, a:      300.00, d:  0.0000%, tcr: 11, cpr:  2.625, div:  7215
+r:      200, a:      200.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 15625
+r:      150, a:      150.00, d:  0.0000%, tcr: 13, cpr:  2.250, div: 14245
+r:      134, a:      134.00, d:  0.0000%, tcr: 11, cpr:  2.625, div: 16153
+r:      110, a:      110.00, d:  0.0000%, tcr: 12, cpr:  1.000, div: 47348
+r:       75, a:       75.00, d:  0.0000%, tcr:  4, cpr:  5.875, div: 35461
+r:       50, a:       50.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 62500
+r:       25, a:       25.00, d:  0.0000%, tcr: 16, cpr:  2.500, div: 62500
+r:        4, a:        4.00, d:  0.0000%, tcr: 16, cpr: 20.000, div: 48828
+r:        2, a:        2.00, d:  0.0000%, tcr: 16, cpr: 40.000, div: 48828
+r:        1, a:        1.00, d:  0.0000%, tcr: 16, cpr: 63.875, div: 61154
+
+With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
+limitation imposed by `serial8250_get_baud_rate' standard baud rates
+below 300bps become unavailable in the regular way, e.g. the rate of
+200bps requires the baud base to be divided by 78125 and that is beyond
+the unsigned 16-bit range.  The historic spd_cust feature can still be
+used by encoding the values for, the prescaler, the oversampling rate
+and the clock divisor (DLM/DLL) as follows to obtain such rates if so
+required:
+
+ 31 29 28             20 19   16 15                            0
++-----+-----------------+-------+-------------------------------+
+|0 0 0|    CPR2:CPR     |  TCR  |            DLM:DLL            |
++-----+-----------------+-------+-------------------------------+
+
+Use a value such encoded for the `custom_divisor' field along with the
+ASYNC_SPD_CUST flag set in the `flags' field in `struct serial_struct'
+passed with the TIOCSSERIAL ioctl(2), such as with the setserial(8)
+utility and its `divisor' and `spd_cust' parameters, and the select
+the baud rate of 38400bps.  Note that the value of 0 in TCR sets the
+oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are
+clamped by the driver to 1.
+
+For example the value of 0x1f4004e2 will set CPR2/CPR, TCR and DLM/DLL
+respectively to 0x1f4, 0x0 and 0x04e2, choosing the prescaler value,
+the oversampling rate and the clock divisor of 62.500, 16 and 1250
+respectively.  These parameters will set the baud rate for the serial
+port to 62500000 / 62.500 / 1250 / 16 = 50bps.
+
+References:
+
+[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
+    Inc., DS-0045, 10 Nov 2008, Section "950 Mode", pp. 64-65
+
+[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
+    Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "950 Mode",
+    p. 20
+
+[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
+    Semiconductor, Inc., DS-0047, Feb 08, Section "950 Mode", p. 20
+
+[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
+    Semiconductor, Inc., DS-0048, Feb 08, Section "950 Mode", p. 20
+
+Maciej W. Rozycki  <macro@orcam.me.uk>
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/ioctl/ioctl-number.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/ioctl/ioctl-number.rst
@@ -304,7 +304,6 @@
 0x89  00-06  arch/x86/include/asm/sockios.h
 0x89  0B-DF  linux/sockios.h
 0x89  E0-EF  linux/sockios.h                                         SIOCPROTOPRIVATE range
-0x89  E0-EF  linux/dn.h                                              PROTOPRIVATE range
 0x89  F0-FF  linux/sockios.h                                         SIOCDEVPRIVATE range
 0x8B  all    linux/wireless.h
 0x8C  00-3F                                                          WiNRADiO driver
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/landlock.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/landlock.rst
@@ -267,8 +267,8 @@
 Ruleset layers
 --------------
 
-There is a limit of 64 layers of stacked rulesets.  This can be an issue for a
-task willing to enforce a new ruleset in complement to its 64 inherited
+There is a limit of 16 layers of stacked rulesets.  This can be an issue for a
+task willing to enforce a new ruleset in complement to its 16 inherited
 rulesets.  Once this limit is reached, sys_landlock_restrict_self() returns
 E2BIG.  It is then strongly suggested to carefully build rulesets once in the
 life of a thread, especially for applications able to launch other applications
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/v4l/biblio.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/v4l/biblio.rst
@@ -417,3 +417,13 @@
 :title:     RFC 6386: "VP8 Data Format and Decoding Guide"
 
 :author:    J. Bankoski et al.
+
+.. _itu2100:
+
+ITU BT.2100
+===========
+
+
+:title:     ITU-R Recommendation BT.2100-2 (07/2018) "Image parameter values for high dynamic range television for use in production and international programme exchange"
+
+:author:    International Telecommunication Union (http://www.itu.int)
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/v4l/colorspaces-defs.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/v4l/colorspaces-defs.rst
@@ -99,6 +99,8 @@
       - Use the DCI-P3 transfer function.
     * - ``V4L2_XFER_FUNC_SMPTE2084``
       - Use the SMPTE 2084 transfer function. See :ref:`xf-smpte-2084`.
+    * - ``V4L2_XFER_FUNC_HLG``
+      - Use the Hybrid Log Gamma(HLG) transfer function. See :ref:`xf-hlg`.
 
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/v4l/colorspaces-details.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/v4l/colorspaces-details.rst
@@ -773,3 +773,34 @@
 
 There are better methods, see e.g. :ref:`colimg` for more in-depth information
 about this.
+
+
+.. _xf-hlg:
+
+Transfer Function HLG (V4L2_XFER_FUNC_HLG)
+=======================================================
+
+The :ref:`itu2100` defines the transfer function used.
+
+Constants:
+
+.. math::
+    a = 0.17883277
+
+    b = 1 - 4 * a = 0.28466892
+
+    c = 0.5 - a * \ln (4 * a) = 0.55991073
+
+Transfer function:
+
+.. math::
+
+     E' = \begin{cases}\sqrt(3 * E) & 0 \leq E \leq \frac{1}{12}
+     \\ a * \ln(12 * E - b) + c & \frac{1}{12} \le E \leq 1\end{cases}
+
+Inverse Transfer function:
+
+.. math::
+
+     x' =\begin{cases}x^{2} / 3  & 0 \leq x \leq \frac{1}{12}
+     \\(exp((x - c) / a) + b) / 12 & \frac{1}{12} \le x \leq 1\end{cases}
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst
@@ -3326,15 +3326,15 @@
     * - __u8
       - ``poc_st_curr_before[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
       - PocStCurrBefore as described in section 8.3.2 "Decoding process for reference
-        picture set.
+        picture set": provides the index of the short term before references in DPB array.
     * - __u8
       - ``poc_st_curr_after[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
       - PocStCurrAfter as described in section 8.3.2 "Decoding process for reference
-        picture set.
+        picture set": provides the index of the short term after references in DPB array.
     * - __u8
       - ``poc_lt_curr[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]``
       - PocLtCurr as described in section 8.3.2 "Decoding process for reference
-        picture set.
+        picture set": provides the index of the long term references in DPB array.
     * - __u64
       - ``flags``
       - See :ref:`Decode Parameters Flags <hevc_decode_params_flags>`
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/v4l/subdev-formats.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/v4l/subdev-formats.rst
@@ -1603,6 +1603,43 @@
       - b\ :sub:`2`
       - b\ :sub:`1`
       - b\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-RBG101010-1X30:
+
+      - MEDIA_BUS_FMT_RBG101010_1X30
+      - 0x1100
+      -
+      - 0
+      - 0
+      - r\ :sub:`9`
+      - r\ :sub:`8`
+      - r\ :sub:`7`
+      - r\ :sub:`6`
+      - r\ :sub:`5`
+      - r\ :sub:`4`
+      - r\ :sub:`3`
+      - r\ :sub:`2`
+      - r\ :sub:`1`
+      - r\ :sub:`0`
+      - b\ :sub:`9`
+      - b\ :sub:`8`
+      - b\ :sub:`7`
+      - b\ :sub:`6`
+      - b\ :sub:`5`
+      - b\ :sub:`4`
+      - b\ :sub:`3`
+      - b\ :sub:`2`
+      - b\ :sub:`1`
+      - b\ :sub:`0`
+      - g\ :sub:`9`
+      - g\ :sub:`8`
+      - g\ :sub:`7`
+      - g\ :sub:`6`
+      - g\ :sub:`5`
+      - g\ :sub:`4`
+      - g\ :sub:`3`
+      - g\ :sub:`2`
+      - g\ :sub:`1`
+      - g\ :sub:`0`
 
 .. raw:: latex
 
@@ -1710,6 +1747,47 @@
       - b\ :sub:`2`
       - b\ :sub:`1`
       - b\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-RBG121212-1X36:
+
+      - MEDIA_BUS_FMT_RBG121212_1X36
+      - 0x1101
+      -
+      - r\ :sub:`11`
+      - r\ :sub:`10`
+      - r\ :sub:`9`
+      - r\ :sub:`8`
+      - r\ :sub:`7`
+      - r\ :sub:`6`
+      - r\ :sub:`5`
+      - r\ :sub:`4`
+      - r\ :sub:`3`
+      - r\ :sub:`2`
+      - r\ :sub:`1`
+      - r\ :sub:`0`
+      - b\ :sub:`11`
+      - b\ :sub:`10`
+      - b\ :sub:`9`
+      - b\ :sub:`8`
+      - b\ :sub:`7`
+      - b\ :sub:`6`
+      - b\ :sub:`5`
+      - b\ :sub:`4`
+      - b\ :sub:`3`
+      - b\ :sub:`2`
+      - b\ :sub:`1`
+      - b\ :sub:`0`
+      - g\ :sub:`11`
+      - g\ :sub:`10`
+      - g\ :sub:`9`
+      - g\ :sub:`8`
+      - g\ :sub:`7`
+      - g\ :sub:`6`
+      - g\ :sub:`5`
+      - g\ :sub:`4`
+      - g\ :sub:`3`
+      - g\ :sub:`2`
+      - g\ :sub:`1`
+      - g\ :sub:`0`
 
 .. raw:: latex
 
@@ -1879,6 +1957,78 @@
       - b\ :sub:`2`
       - b\ :sub:`1`
       - b\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-RBG161616-1X48:
+
+      - MEDIA_BUS_FMT_RBG161616_1X48
+      - 0x1102
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - r\ :sub:`15`
+      - r\ :sub:`14`
+      - r\ :sub:`13`
+      - r\ :sub:`12`
+      - r\ :sub:`11`
+      - r\ :sub:`10`
+      - r\ :sub:`9`
+      - r\ :sub:`8`
+      - r\ :sub:`7`
+      - r\ :sub:`6`
+      - r\ :sub:`5`
+      - r\ :sub:`4`
+      - r\ :sub:`3`
+      - r\ :sub:`2`
+      - r\ :sub:`1`
+      - r\ :sub:`0`
+    * -
+      -
+      -
+      - b\ :sub:`15`
+      - b\ :sub:`14`
+      - b\ :sub:`13`
+      - b\ :sub:`12`
+      - b\ :sub:`11`
+      - b\ :sub:`10`
+      - b\ :sub:`9`
+      - b\ :sub:`8`
+      - b\ :sub:`7`
+      - b\ :sub:`6`
+      - b\ :sub:`5`
+      - b\ :sub:`4`
+      - b\ :sub:`3`
+      - b\ :sub:`2`
+      - b\ :sub:`1`
+      - b\ :sub:`0`
+      - g\ :sub:`15`
+      - g\ :sub:`14`
+      - g\ :sub:`13`
+      - g\ :sub:`12`
+      - g\ :sub:`11`
+      - g\ :sub:`10`
+      - g\ :sub:`9`
+      - g\ :sub:`8`
+      - g\ :sub:`7`
+      - g\ :sub:`6`
+      - g\ :sub:`5`
+      - g\ :sub:`4`
+      - g\ :sub:`3`
+      - g\ :sub:`2`
+      - g\ :sub:`1`
+      - g\ :sub:`0`
 
 .. raw:: latex
 
@@ -5259,6 +5409,148 @@
       - u\ :sub:`2`
       - u\ :sub:`1`
       - u\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-VYYUYY10_4X20:
+
+      - MEDIA_BUS_FMT_VYYUYY10_4X20
+      - 0x2101
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-Y12-1X12:
 
       - MEDIA_BUS_FMT_Y12_1X12
@@ -7053,6 +7345,185 @@
       - u\ :sub:`2`
       - u\ :sub:`1`
       - u\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-UYYVYY12-4X24:
+
+      - MEDIA_BUS_FMT_UYYVYY12_4X24
+      - 0x2103
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - u\ :sub:`11`
+      - u\ :sub:`10`
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - v\ :sub:`11`
+      - v\ :sub:`10`
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-VYYUYY8-1X24:
+
+      - MEDIA_BUS_FMT_VYYUYY8_1X24
+      - 0x2100
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-YUV10-1X30:
 
       - MEDIA_BUS_FMT_YUV10_1X30
@@ -7090,6 +7561,43 @@
       - v\ :sub:`2`
       - v\ :sub:`1`
       - v\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-VUY10-1X30:
+
+      - MEDIA_BUS_FMT_VUY10_1X30
+      - 0x2102
+      -
+      -
+      -
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-UYYVYY10-0-5X30:
 
       - MEDIA_BUS_FMT_UYYVYY10_0_5X30
@@ -7162,6 +7670,43 @@
       - y\ :sub:`2`
       - y\ :sub:`1`
       - y\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-Y16-1X16:
+
+      - MEDIA_BUS_FMT_Y16_1X16
+      - 0x2105
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-AYUV8-1X32:
 
       - MEDIA_BUS_FMT_AYUV8_1X32
@@ -7199,6 +7744,220 @@
       - v\ :sub:`2`
       - v\ :sub:`1`
       - v\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-UYYVYY16-4X32:
+
+      - MEDIA_BUS_FMT_UYYVYY16_4X32
+      - 0x2106
+      -
+      - u\ :sub:`15`
+      - u\ :sub:`14`
+      - u\ :sub:`13`
+      - u\ :sub:`12`
+      - u\ :sub:`11`
+      - u\ :sub:`10`
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      - v\ :sub:`15`
+      - v\ :sub:`14`
+      - v\ :sub:`13`
+      - v\ :sub:`12`
+      - v\ :sub:`11`
+      - v\ :sub:`10`
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-UYVY16-2X32:
+
+      - MEDIA_BUS_FMT_UYVY16_2X32
+      - 0x2108
+      -
+      - u\ :sub:`15`
+      - u\ :sub:`14`
+      - u\ :sub:`13`
+      - u\ :sub:`12`
+      - u\ :sub:`11`
+      - u\ :sub:`10`
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
+    * -
+      -
+      -
+      - v\ :sub:`15`
+      - v\ :sub:`14`
+      - v\ :sub:`13`
+      - v\ :sub:`12`
+      - v\ :sub:`11`
+      - v\ :sub:`10`
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
 
 
 .. raw:: latex
@@ -7387,6 +8146,47 @@
       - v\ :sub:`2`
       - v\ :sub:`1`
       - v\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-VUY12-1X36:
+
+      - MEDIA_BUS_FMT_VUY12_1X36
+      - 0x2104
+      -
+      - v\ :sub:`11`
+      - v\ :sub:`10`
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+      - u\ :sub:`11`
+      - u\ :sub:`10`
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
 
 
 .. raw:: latex
@@ -7557,6 +8357,78 @@
       - v\ :sub:`2`
       - v\ :sub:`1`
       - v\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-VUY16-1X48:
+
+      - MEDIA_BUS_FMT_VUY16_1X48
+      - 0x2107
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - v\ :sub:`15`
+      - v\ :sub:`14`
+      - v\ :sub:`13`
+      - v\ :sub:`12`
+      - v\ :sub:`11`
+      - v\ :sub:`10`
+      - v\ :sub:`9`
+      - v\ :sub:`8`
+      - v\ :sub:`7`
+      - v\ :sub:`6`
+      - v\ :sub:`5`
+      - v\ :sub:`4`
+      - v\ :sub:`3`
+      - v\ :sub:`2`
+      - v\ :sub:`1`
+      - v\ :sub:`0`
+    * -
+      -
+      -
+      - u\ :sub:`15`
+      - u\ :sub:`14`
+      - u\ :sub:`13`
+      - u\ :sub:`12`
+      - u\ :sub:`11`
+      - u\ :sub:`10`
+      - u\ :sub:`9`
+      - u\ :sub:`8`
+      - u\ :sub:`7`
+      - u\ :sub:`6`
+      - u\ :sub:`5`
+      - u\ :sub:`4`
+      - u\ :sub:`3`
+      - u\ :sub:`2`
+      - u\ :sub:`1`
+      - u\ :sub:`0`
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`8`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-UYYVYY16-0-5X48:
 
       - MEDIA_BUS_FMT_UYYVYY16_0_5X48
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/v4l/vidioc-queryctrl.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/v4l/vidioc-queryctrl.rst
@@ -471,6 +471,12 @@
       - n/a
       - A struct :c:type:`v4l2_ctrl_h264_decode_params`, containing H264
 	decode parameters for stateless video decoders.
+    * - ``V4L2_CTRL_TYPE_HDR``
+      - n/a
+      - n/a
+      - n/a
+      - A struct :c:type:`v4l2_metadata_hdr`, containing HDR
+	metadata.
     * - ``V4L2_CTRL_TYPE_FWHT_PARAMS``
       - n/a
       - n/a
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/userspace-api/media/videodev2.h.rst.exceptions
+++ linux-xilinx-zynqmp-5.15.0/Documentation/userspace-api/media/videodev2.h.rst.exceptions
@@ -81,6 +81,7 @@
 replace symbol V4L2_XFER_FUNC_SMPTE2084 :c:type:`v4l2_xfer_func`
 replace symbol V4L2_XFER_FUNC_SMPTE240M :c:type:`v4l2_xfer_func`
 replace symbol V4L2_XFER_FUNC_SRGB :c:type:`v4l2_xfer_func`
+replace symbol V4L2_XFER_FUNC_HLG :c:type:`v4l2_xfer_func`
 
 # Documented enum v4l2_ycbcr_encoding
 replace symbol V4L2_YCBCR_ENC_601 :c:type:`v4l2_ycbcr_encoding`
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/api.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/api.rst
@@ -3462,15 +3462,17 @@
 4.89 KVM_S390_MEM_OP
 --------------------
 
-:Capability: KVM_CAP_S390_MEM_OP
+:Capability: KVM_CAP_S390_MEM_OP, KVM_CAP_S390_PROTECTED, KVM_CAP_S390_MEM_OP_EXTENSION
 :Architectures: s390
-:Type: vcpu ioctl
+:Type: vm ioctl, vcpu ioctl
 :Parameters: struct kvm_s390_mem_op (in)
 :Returns: = 0 on success,
           < 0 on generic error (e.g. -EFAULT or -ENOMEM),
           > 0 if an exception occurred while walking the page tables
 
-Read or write data from/to the logical (virtual) memory of a VCPU.
+Read or write data from/to the VM's memory.
+The KVM_CAP_S390_MEM_OP_EXTENSION capability specifies what functionality is
+supported.
 
 Parameters are specified via the following structure::
 
@@ -3480,33 +3482,99 @@
 	__u32 size;		/* amount of bytes */
 	__u32 op;		/* type of operation */
 	__u64 buf;		/* buffer in userspace */
-	__u8 ar;		/* the access register number */
-	__u8 reserved[31];	/* should be set to 0 */
+	union {
+		struct {
+			__u8 ar;	/* the access register number */
+			__u8 key;	/* access key, ignored if flag unset */
+		};
+		__u32 sida_offset; /* offset into the sida */
+		__u8 reserved[32]; /* ignored */
+	};
   };
 
-The type of operation is specified in the "op" field. It is either
-KVM_S390_MEMOP_LOGICAL_READ for reading from logical memory space or
-KVM_S390_MEMOP_LOGICAL_WRITE for writing to logical memory space. The
-KVM_S390_MEMOP_F_CHECK_ONLY flag can be set in the "flags" field to check
-whether the corresponding memory access would create an access exception
-(without touching the data in the memory at the destination). In case an
-access exception occurred while walking the MMU tables of the guest, the
-ioctl returns a positive error number to indicate the type of exception.
-This exception is also raised directly at the corresponding VCPU if the
-flag KVM_S390_MEMOP_F_INJECT_EXCEPTION is set in the "flags" field.
-
 The start address of the memory region has to be specified in the "gaddr"
 field, and the length of the region in the "size" field (which must not
 be 0). The maximum value for "size" can be obtained by checking the
 KVM_CAP_S390_MEM_OP capability. "buf" is the buffer supplied by the
 userspace application where the read data should be written to for
-KVM_S390_MEMOP_LOGICAL_READ, or where the data that should be written is
-stored for a KVM_S390_MEMOP_LOGICAL_WRITE. When KVM_S390_MEMOP_F_CHECK_ONLY
-is specified, "buf" is unused and can be NULL. "ar" designates the access
-register number to be used; the valid range is 0..15.
+a read access, or where the data that should be written is stored for
+a write access.  The "reserved" field is meant for future extensions.
+Reserved and unused values are ignored. Future extension that add members must
+introduce new flags.
+
+The type of operation is specified in the "op" field. Flags modifying
+their behavior can be set in the "flags" field. Undefined flag bits must
+be set to 0.
+
+Possible operations are:
+  * ``KVM_S390_MEMOP_LOGICAL_READ``
+  * ``KVM_S390_MEMOP_LOGICAL_WRITE``
+  * ``KVM_S390_MEMOP_ABSOLUTE_READ``
+  * ``KVM_S390_MEMOP_ABSOLUTE_WRITE``
+  * ``KVM_S390_MEMOP_SIDA_READ``
+  * ``KVM_S390_MEMOP_SIDA_WRITE``
+
+Logical read/write:
+^^^^^^^^^^^^^^^^^^^
+
+Access logical memory, i.e. translate the given guest address to an absolute
+address given the state of the VCPU and use the absolute address as target of
+the access. "ar" designates the access register number to be used; the valid
+range is 0..15.
+Logical accesses are permitted for the VCPU ioctl only.
+Logical accesses are permitted for non-protected guests only.
+
+Supported flags:
+  * ``KVM_S390_MEMOP_F_CHECK_ONLY``
+  * ``KVM_S390_MEMOP_F_INJECT_EXCEPTION``
+  * ``KVM_S390_MEMOP_F_SKEY_PROTECTION``
+
+The KVM_S390_MEMOP_F_CHECK_ONLY flag can be set to check whether the
+corresponding memory access would cause an access exception; however,
+no actual access to the data in memory at the destination is performed.
+In this case, "buf" is unused and can be NULL.
+
+In case an access exception occurred during the access (or would occur
+in case of KVM_S390_MEMOP_F_CHECK_ONLY), the ioctl returns a positive
+error number indicating the type of exception. This exception is also
+raised directly at the corresponding VCPU if the flag
+KVM_S390_MEMOP_F_INJECT_EXCEPTION is set.
+
+If the KVM_S390_MEMOP_F_SKEY_PROTECTION flag is set, storage key
+protection is also in effect and may cause exceptions if accesses are
+prohibited given the access key designated by "key"; the valid range is 0..15.
+KVM_S390_MEMOP_F_SKEY_PROTECTION is available if KVM_CAP_S390_MEM_OP_EXTENSION
+is > 0.
+
+Absolute read/write:
+^^^^^^^^^^^^^^^^^^^^
+
+Access absolute memory. This operation is intended to be used with the
+KVM_S390_MEMOP_F_SKEY_PROTECTION flag, to allow accessing memory and performing
+the checks required for storage key protection as one operation (as opposed to
+user space getting the storage keys, performing the checks, and accessing
+memory thereafter, which could lead to a delay between check and access).
+Absolute accesses are permitted for the VM ioctl if KVM_CAP_S390_MEM_OP_EXTENSION
+is > 0.
+Currently absolute accesses are not permitted for VCPU ioctls.
+Absolute accesses are permitted for non-protected guests only.
+
+Supported flags:
+  * ``KVM_S390_MEMOP_F_CHECK_ONLY``
+  * ``KVM_S390_MEMOP_F_SKEY_PROTECTION``
+
+The semantics of the flags are as for logical accesses.
+
+SIDA read/write:
+^^^^^^^^^^^^^^^^
+
+Access the secure instruction data area which contains memory operands necessary
+for instruction emulation for protected guests.
+SIDA accesses are available if the KVM_CAP_S390_PROTECTED capability is available.
+SIDA accesses are permitted for the VCPU ioctl only.
+SIDA accesses are permitted for protected guests only.
 
-The "reserved" field is meant for future extensions. It is not used by
-KVM with the currently defined set of flags.
+No flags are supported.
 
 4.90 KVM_S390_GET_SKEYS
 -----------------------
@@ -4117,6 +4185,18 @@
 :Parameters: struct kvm_s390_cmma_log (in, out)
 :Returns: 0 on success, a negative value on error
 
+Errors:
+
+  ======     =============================================================
+  ENOMEM     not enough memory can be allocated to complete the task
+  ENXIO      if CMMA is not enabled
+  EINVAL     if KVM_S390_CMMA_PEEK is not set but migration mode was not enabled
+  EINVAL     if KVM_S390_CMMA_PEEK is not set but dirty tracking has been
+             disabled (and thus migration mode was automatically disabled)
+  EFAULT     if the userspace address is invalid or if no page table is
+             present for the addresses (e.g. when using hugepages).
+  ======     =============================================================
+
 This ioctl is used to get the values of the CMMA bits on the s390
 architecture. It is meant to be used in two scenarios:
 
@@ -4197,12 +4277,6 @@
 
 values points to the userspace buffer where the result will be stored.
 
-This ioctl can fail with -ENOMEM if not enough memory can be allocated to
-complete the task, with -ENXIO if CMMA is not enabled, with -EINVAL if
-KVM_S390_CMMA_PEEK is not set but migration mode was not enabled, with
--EFAULT if the userspace address is invalid or if no page table is
-present for the addresses (e.g. when using hugepages).
-
 4.108 KVM_S390_SET_CMMA_BITS
 ----------------------------
 
@@ -4773,7 +4847,15 @@
 	__u32 reserved[3];
   };
 
-cmd values:
+**Ultravisor return codes**
+The Ultravisor return (reason) codes are provided by the kernel if a
+Ultravisor call has been executed to achieve the results expected by
+the command. Therefore they are independent of the IOCTL return
+code. If KVM changes `rc`, its value will always be greater than 0
+hence setting it to 0 before issuing a PV command is advised to be
+able to detect a change of `rc`.
+
+**cmd values:**
 
 KVM_PV_ENABLE
   Allocate memory and register the VM with the Ultravisor, thereby
@@ -4789,7 +4871,6 @@
   =====      =============================
 
 KVM_PV_DISABLE
-
   Deregister the VM from the Ultravisor and reclaim the memory that
   had been donated to the Ultravisor, making it usable by the kernel
   again.  All registered VCPUs are converted back to non-protected
@@ -4806,6 +4887,117 @@
   Verify the integrity of the unpacked image. Only if this succeeds,
   KVM is allowed to start protected VCPUs.
 
+KVM_PV_INFO
+  :Capability: KVM_CAP_S390_PROTECTED_DUMP
+
+  Presents an API that provides Ultravisor related data to userspace
+  via subcommands. len_max is the size of the user space buffer,
+  len_written is KVM's indication of how much bytes of that buffer
+  were actually written to. len_written can be used to determine the
+  valid fields if more response fields are added in the future.
+
+  ::
+
+     enum pv_cmd_info_id {
+	KVM_PV_INFO_VM,
+	KVM_PV_INFO_DUMP,
+     };
+
+     struct kvm_s390_pv_info_header {
+	__u32 id;
+	__u32 len_max;
+	__u32 len_written;
+	__u32 reserved;
+     };
+
+     struct kvm_s390_pv_info {
+	struct kvm_s390_pv_info_header header;
+	struct kvm_s390_pv_info_dump dump;
+	struct kvm_s390_pv_info_vm vm;
+     };
+
+**subcommands:**
+
+  KVM_PV_INFO_VM
+    This subcommand provides basic Ultravisor information for PV
+    hosts. These values are likely also exported as files in the sysfs
+    firmware UV query interface but they are more easily available to
+    programs in this API.
+
+    The installed calls and feature_indication members provide the
+    installed UV calls and the UV's other feature indications.
+
+    The max_* members provide information about the maximum number of PV
+    vcpus, PV guests and PV guest memory size.
+
+    ::
+
+      struct kvm_s390_pv_info_vm {
+	__u64 inst_calls_list[4];
+	__u64 max_cpus;
+	__u64 max_guests;
+	__u64 max_guest_addr;
+	__u64 feature_indication;
+      };
+
+
+  KVM_PV_INFO_DUMP
+    This subcommand provides information related to dumping PV guests.
+
+    ::
+
+      struct kvm_s390_pv_info_dump {
+	__u64 dump_cpu_buffer_len;
+	__u64 dump_config_mem_buffer_per_1m;
+	__u64 dump_config_finalize_len;
+      };
+
+KVM_PV_DUMP
+  :Capability: KVM_CAP_S390_PROTECTED_DUMP
+
+  Presents an API that provides calls which facilitate dumping a
+  protected VM.
+
+  ::
+
+    struct kvm_s390_pv_dmp {
+      __u64 subcmd;
+      __u64 buff_addr;
+      __u64 buff_len;
+      __u64 gaddr;		/* For dump storage state */
+    };
+
+  **subcommands:**
+
+  KVM_PV_DUMP_INIT
+    Initializes the dump process of a protected VM. If this call does
+    not succeed all other subcommands will fail with -EINVAL. This
+    subcommand will return -EINVAL if a dump process has not yet been
+    completed.
+
+    Not all PV vms can be dumped, the owner needs to set `dump
+    allowed` PCF bit 34 in the SE header to allow dumping.
+
+  KVM_PV_DUMP_CONFIG_STOR_STATE
+     Stores `buff_len` bytes of tweak component values starting with
+     the 1MB block specified by the absolute guest address
+     (`gaddr`). `buff_len` needs to be `conf_dump_storage_state_len`
+     aligned and at least >= the `conf_dump_storage_state_len` value
+     provided by the dump uv_info data. buff_user might be written to
+     even if an error rc is returned. For instance if we encounter a
+     fault after writing the first page of data.
+
+  KVM_PV_DUMP_COMPLETE
+    If the subcommand succeeds it completes the dump process and lets
+    KVM_PV_DUMP_INIT be called again.
+
+    On success `conf_dump_finalize_len` bytes of completion data will be
+    stored to the `buff_addr`. The completion data contains a key
+    derivation seed, IV, tweak nonce and encryption keys as well as an
+    authentication tag all of which are needed to decrypt the dump at a
+    later time.
+
+
 4.126 KVM_X86_SET_MSR_FILTER
 ----------------------------
 
@@ -5317,6 +5509,79 @@
 The Stats Data block contains an array of 64-bit values in the same order
 as the descriptors in Descriptors block.
 
+4.137 KVM_S390_ZPCI_OP
+----------------------
+
+:Capability: KVM_CAP_S390_ZPCI_OP
+:Architectures: s390
+:Type: vm ioctl
+:Parameters: struct kvm_s390_zpci_op (in)
+:Returns: 0 on success, <0 on error
+
+Used to manage hardware-assisted virtualization features for zPCI devices.
+
+Parameters are specified via the following structure::
+
+  struct kvm_s390_zpci_op {
+	/* in */
+	__u32 fh;		/* target device */
+	__u8  op;		/* operation to perform */
+	__u8  pad[3];
+	union {
+		/* for KVM_S390_ZPCIOP_REG_AEN */
+		struct {
+			__u64 ibv;	/* Guest addr of interrupt bit vector */
+			__u64 sb;	/* Guest addr of summary bit */
+			__u32 flags;
+			__u32 noi;	/* Number of interrupts */
+			__u8 isc;	/* Guest interrupt subclass */
+			__u8 sbo;	/* Offset of guest summary bit vector */
+			__u16 pad;
+		} reg_aen;
+		__u64 reserved[8];
+	} u;
+  };
+
+The type of operation is specified in the "op" field.
+KVM_S390_ZPCIOP_REG_AEN is used to register the VM for adapter event
+notification interpretation, which will allow firmware delivery of adapter
+events directly to the vm, with KVM providing a backup delivery mechanism;
+KVM_S390_ZPCIOP_DEREG_AEN is used to subsequently disable interpretation of
+adapter event notifications.
+
+The target zPCI function must also be specified via the "fh" field.  For the
+KVM_S390_ZPCIOP_REG_AEN operation, additional information to establish firmware
+delivery must be provided via the "reg_aen" struct.
+
+The "pad" and "reserved" fields may be used for future extensions and should be
+set to 0s by userspace.
+
+4.136 KVM_S390_PV_CPU_COMMAND
+-----------------------------
+
+:Capability: KVM_CAP_S390_PROTECTED_DUMP
+:Architectures: s390
+:Type: vcpu ioctl
+:Parameters: none
+:Returns: 0 on success, < 0 on error
+
+This ioctl closely mirrors `KVM_S390_PV_COMMAND` but handles requests
+for vcpus. It re-uses the kvm_s390_pv_dmp struct and hence also shares
+the command ids.
+
+**command:**
+
+KVM_PV_DUMP
+  Presents an API that provides calls which facilitate dumping a vcpu
+  of a protected VM.
+
+**subcommand:**
+
+KVM_PV_DUMP_CPU
+  Provides encrypted dump data like register values.
+  The length of the returned data is provided by uv_info.guest_cpu_stor_len.
+
+
 5. The kvm_run structure
 ========================
 
@@ -7265,3 +7530,76 @@
 of the result of KVM_CHECK_EXTENSION.  KVM will forward to userspace
 the hypercalls whose corresponding bit is in the argument, and return
 ENOSYS for the others.
+
+8.37 KVM_CAP_S390_PROTECTED_DUMP
+--------------------------------
+
+:Capability: KVM_CAP_S390_PROTECTED_DUMP
+:Architectures: s390
+:Type: vm
+
+This capability indicates that KVM and the Ultravisor support dumping
+PV guests. The `KVM_PV_DUMP` command is available for the
+`KVM_S390_PV_COMMAND` ioctl and the `KVM_PV_INFO` command provides
+dump related UV data. Also the vcpu ioctl `KVM_S390_PV_CPU_COMMAND` is
+available and supports the `KVM_PV_DUMP_CPU` subcommand.
+
+9. Known KVM API problems
+=========================
+
+In some cases, KVM's API has some inconsistencies or common pitfalls
+that userspace need to be aware of.  This section details some of
+these issues.
+
+Most of them are architecture specific, so the section is split by
+architecture.
+
+9.1. x86
+--------
+
+``KVM_GET_SUPPORTED_CPUID`` issues
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+In general, ``KVM_GET_SUPPORTED_CPUID`` is designed so that it is possible
+to take its result and pass it directly to ``KVM_SET_CPUID2``.  This section
+documents some cases in which that requires some care.
+
+Local APIC features
+~~~~~~~~~~~~~~~~~~~
+
+CPU[EAX=1]:ECX[21] (X2APIC) is reported by ``KVM_GET_SUPPORTED_CPUID``,
+but it can only be enabled if ``KVM_CREATE_IRQCHIP`` or
+``KVM_ENABLE_CAP(KVM_CAP_IRQCHIP_SPLIT)`` are used to enable in-kernel emulation of
+the local APIC.
+
+The same is true for the ``KVM_FEATURE_PV_UNHALT`` paravirtualized feature.
+
+CPU[EAX=1]:ECX[24] (TSC_DEADLINE) is not reported by ``KVM_GET_SUPPORTED_CPUID``.
+It can be enabled if ``KVM_CAP_TSC_DEADLINE_TIMER`` is present and the kernel
+has enabled in-kernel emulation of the local APIC.
+
+CPU topology
+~~~~~~~~~~~~
+
+Several CPUID values include topology information for the host CPU:
+0x0b and 0x1f for Intel systems, 0x8000001e for AMD systems.  Different
+versions of KVM return different values for this information and userspace
+should not rely on it.  Currently they return all zeroes.
+
+If userspace wishes to set up a guest topology, it should be careful that
+the values of these three leaves differ for each CPU.  In particular,
+the APIC ID is found in EDX for all subleaves of 0x0b and 0x1f, and in EAX
+for 0x8000001e; the latter also encodes the core id and node id in bits
+7:0 of EBX and ECX respectively.
+
+Obsolete ioctls and capabilities
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+KVM_CAP_DISABLE_QUIRKS does not let userspace know which quirks are actually
+available.  Use ``KVM_CHECK_EXTENSION(KVM_CAP_DISABLE_QUIRKS2)`` instead if
+available.
+
+Ordering of KVM_GET_*/KVM_SET_* ioctls
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+TBD
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/devices/vm.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/devices/vm.rst
@@ -215,6 +215,7 @@
 :Parameters: address of a buffer in user space to store the data (u8) to
 :Returns:   -EFAULT if the given address is not accessible from kernel space;
 	    -EINVAL if setting the TOD clock extension to != 0 is not supported
+	    -EOPNOTSUPP for a PV guest (TOD managed by the ultravisor)
 
 3.2. ATTRIBUTE: KVM_S390_VM_TOD_LOW
 -----------------------------------
@@ -224,6 +225,7 @@
 
 :Parameters: address of a buffer in user space to store the data (u64) to
 :Returns:    -EFAULT if the given address is not accessible from kernel space
+	     -EOPNOTSUPP for a PV guest (TOD managed by the ultravisor)
 
 3.3. ATTRIBUTE: KVM_S390_VM_TOD_EXT
 -----------------------------------
@@ -237,6 +239,7 @@
 	     (kvm_s390_vm_tod_clock) to
 :Returns:   -EFAULT if the given address is not accessible from kernel space;
 	    -EINVAL if setting the TOD clock extension to != 0 is not supported
+	    -EOPNOTSUPP for a PV guest (TOD managed by the ultravisor)
 
 4. GROUP: KVM_S390_VM_CRYPTO
 ============================
@@ -299,6 +302,10 @@
 Setting this attribute when migration mode is already active will have
 no effects.
 
+Dirty tracking must be enabled on all memslots, else -EINVAL is returned. When
+dirty tracking is disabled on any memslot, migration mode is automatically
+stopped.
+
 :Parameters: none
 :Returns:   -ENOMEM if there is not enough free memory to start migration mode;
 	    -EINVAL if the state of the VM is invalid (e.g. no memory defined);
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/index.rst
@@ -8,25 +8,13 @@
    :maxdepth: 2
 
    api
-   amd-memory-encryption
-   cpuid
-   halt-polling
-   hypercalls
-   locking
-   mmu
-   msr
-   nested-vmx
-   ppc-pv
-   s390-diag
-   s390-pv
-   s390-pv-boot
-   timekeeping
-   vcpu-requests
-
-   review-checklist
+   devices/index
 
    arm/index
+   s390/index
+   ppc-pv
+   x86/index
 
-   devices/index
-
-   running-nested-guests
+   locking
+   vcpu-requests
+   review-checklist
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/s390/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/s390/index.rst
@@ -0,0 +1,13 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================
+KVM for s390 systems
+====================
+
+.. toctree::
+   :maxdepth: 2
+
+   s390-diag
+   s390-pv
+   s390-pv-boot
+   s390-pv-dump
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/s390/s390-diag.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/s390/s390-diag.rst
@@ -0,0 +1,119 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=============================
+The s390 DIAGNOSE call on KVM
+=============================
+
+KVM on s390 supports the DIAGNOSE call for making hypercalls, both for
+native hypercalls and for selected hypercalls found on other s390
+hypervisors.
+
+Note that bits are numbered as by the usual s390 convention (most significant
+bit on the left).
+
+
+General remarks
+---------------
+
+DIAGNOSE calls by the guest cause a mandatory intercept. This implies
+all supported DIAGNOSE calls need to be handled by either KVM or its
+userspace.
+
+All DIAGNOSE calls supported by KVM use the RS-a format::
+
+  --------------------------------------
+  |  '83'  | R1 | R3 | B2 |     D2     |
+  --------------------------------------
+  0        8    12   16   20           31
+
+The second-operand address (obtained by the base/displacement calculation)
+is not used to address data. Instead, bits 48-63 of this address specify
+the function code, and bits 0-47 are ignored.
+
+The supported DIAGNOSE function codes vary by the userspace used. For
+DIAGNOSE function codes not specific to KVM, please refer to the
+documentation for the s390 hypervisors defining them.
+
+
+DIAGNOSE function code 'X'500' - KVM virtio functions
+-----------------------------------------------------
+
+If the function code specifies 0x500, various virtio-related functions
+are performed.
+
+General register 1 contains the virtio subfunction code. Supported
+virtio subfunctions depend on KVM's userspace. Generally, userspace
+provides either s390-virtio (subcodes 0-2) or virtio-ccw (subcode 3).
+
+Upon completion of the DIAGNOSE instruction, general register 2 contains
+the function's return code, which is either a return code or a subcode
+specific value.
+
+Subcode 0 - s390-virtio notification and early console printk
+    Handled by userspace.
+
+Subcode 1 - s390-virtio reset
+    Handled by userspace.
+
+Subcode 2 - s390-virtio set status
+    Handled by userspace.
+
+Subcode 3 - virtio-ccw notification
+    Handled by either userspace or KVM (ioeventfd case).
+
+    General register 2 contains a subchannel-identification word denoting
+    the subchannel of the virtio-ccw proxy device to be notified.
+
+    General register 3 contains the number of the virtqueue to be notified.
+
+    General register 4 contains a 64bit identifier for KVM usage (the
+    kvm_io_bus cookie). If general register 4 does not contain a valid
+    identifier, it is ignored.
+
+    After completion of the DIAGNOSE call, general register 2 may contain
+    a 64bit identifier (in the kvm_io_bus cookie case), or a negative
+    error value, if an internal error occurred.
+
+    See also the virtio standard for a discussion of this hypercall.
+
+
+DIAGNOSE function code 'X'501 - KVM breakpoint
+----------------------------------------------
+
+If the function code specifies 0x501, breakpoint functions may be performed.
+This function code is handled by userspace.
+
+This diagnose function code has no subfunctions and uses no parameters.
+
+
+DIAGNOSE function code 'X'9C - Voluntary Time Slice Yield
+---------------------------------------------------------
+
+General register 1 contains the target CPU address.
+
+In a guest of a hypervisor like LPAR, KVM or z/VM using shared host CPUs,
+DIAGNOSE with function code 0x9c may improve system performance by
+yielding the host CPU on which the guest CPU is running to be assigned
+to another guest CPU, preferably the logical CPU containing the specified
+target CPU.
+
+
+DIAG 'X'9C forwarding
++++++++++++++++++++++
+
+The guest may send a DIAGNOSE 0x9c in order to yield to a certain
+other vcpu. An example is a Linux guest that tries to yield to the vcpu
+that is currently holding a spinlock, but not running.
+
+However, on the host the real cpu backing the vcpu may itself not be
+running.
+Forwarding the DIAGNOSE 0x9c initially sent by the guest to yield to
+the backing cpu will hopefully cause that cpu, and thus subsequently
+the guest's vcpu, to be scheduled.
+
+
+diag9c_forwarding_hz
+    KVM kernel parameter allowing to specify the maximum number of DIAGNOSE
+    0x9c forwarding per second in the purpose of avoiding a DIAGNOSE 0x9c
+    forwarding storm.
+    A value of 0 turns the forwarding off.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/s390/s390-pv-boot.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/s390/s390-pv-boot.rst
@@ -0,0 +1,84 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================
+s390 (IBM Z) Boot/IPL of Protected VMs
+======================================
+
+Summary
+-------
+The memory of Protected Virtual Machines (PVMs) is not accessible to
+I/O or the hypervisor. In those cases where the hypervisor needs to
+access the memory of a PVM, that memory must be made accessible.
+Memory made accessible to the hypervisor will be encrypted. See
+Documentation/virt/kvm/s390-pv.rst for details."
+
+On IPL (boot) a small plaintext bootloader is started, which provides
+information about the encrypted components and necessary metadata to
+KVM to decrypt the protected virtual machine.
+
+Based on this data, KVM will make the protected virtual machine known
+to the Ultravisor (UV) and instruct it to secure the memory of the
+PVM, decrypt the components and verify the data and address list
+hashes, to ensure integrity. Afterwards KVM can run the PVM via the
+SIE instruction which the UV will intercept and execute on KVM's
+behalf.
+
+As the guest image is just like an opaque kernel image that does the
+switch into PV mode itself, the user can load encrypted guest
+executables and data via every available method (network, dasd, scsi,
+direct kernel, ...) without the need to change the boot process.
+
+
+Diag308
+-------
+This diagnose instruction is the basic mechanism to handle IPL and
+related operations for virtual machines. The VM can set and retrieve
+IPL information blocks, that specify the IPL method/devices and
+request VM memory and subsystem resets, as well as IPLs.
+
+For PVMs this concept has been extended with new subcodes:
+
+Subcode 8: Set an IPL Information Block of type 5 (information block
+for PVMs)
+Subcode 9: Store the saved block in guest memory
+Subcode 10: Move into Protected Virtualization mode
+
+The new PV load-device-specific-parameters field specifies all data
+that is necessary to move into PV mode.
+
+* PV Header origin
+* PV Header length
+* List of Components composed of
+   * AES-XTS Tweak prefix
+   * Origin
+   * Size
+
+The PV header contains the keys and hashes, which the UV will use to
+decrypt and verify the PV, as well as control flags and a start PSW.
+
+The components are for instance an encrypted kernel, kernel parameters
+and initrd. The components are decrypted by the UV.
+
+After the initial import of the encrypted data, all defined pages will
+contain the guest content. All non-specified pages will start out as
+zero pages on first access.
+
+
+When running in protected virtualization mode, some subcodes will result in
+exceptions or return error codes.
+
+Subcodes 4 and 7, which specify operations that do not clear the guest
+memory, will result in specification exceptions. This is because the
+UV will clear all memory when a secure VM is removed, and therefore
+non-clearing IPL subcodes are not allowed.
+
+Subcodes 8, 9, 10 will result in specification exceptions.
+Re-IPL into a protected mode is only possible via a detour into non
+protected mode.
+
+Keys
+----
+Every CEC will have a unique public key to enable tooling to build
+encrypted images.
+See  `s390-tools <https://github.com/ibm-s390-linux/s390-tools/>`_
+for the tooling.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/s390/s390-pv-dump.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/s390/s390-pv-dump.rst
@@ -0,0 +1,64 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===========================================
+s390 (IBM Z) Protected Virtualization dumps
+===========================================
+
+Summary
+-------
+
+Dumping a VM is an essential tool for debugging problems inside
+it. This is especially true when a protected VM runs into trouble as
+there's no way to access its memory and registers from the outside
+while it's running.
+
+However when dumping a protected VM we need to maintain its
+confidentiality until the dump is in the hands of the VM owner who
+should be the only one capable of analysing it.
+
+The confidentiality of the VM dump is ensured by the Ultravisor who
+provides an interface to KVM over which encrypted CPU and memory data
+can be requested. The encryption is based on the Customer
+Communication Key which is the key that's used to encrypt VM data in a
+way that the customer is able to decrypt.
+
+
+Dump process
+------------
+
+A dump is done in 3 steps:
+
+**Initiation**
+
+This step initializes the dump process, generates cryptographic seeds
+and extracts dump keys with which the VM dump data will be encrypted.
+
+**Data gathering**
+
+Currently there are two types of data that can be gathered from a VM:
+the memory and the vcpu state.
+
+The vcpu state contains all the important registers, general, floating
+point, vector, control and tod/timers of a vcpu. The vcpu dump can
+contain incomplete data if a vcpu is dumped while an instruction is
+emulated with help of the hypervisor. This is indicated by a flag bit
+in the dump data. For the same reason it is very important to not only
+write out the encrypted vcpu state, but also the unencrypted state
+from the hypervisor.
+
+The memory state is further divided into the encrypted memory and its
+metadata comprised of the encryption tweaks and status flags. The
+encrypted memory can simply be read once it has been exported. The
+time of the export does not matter as no re-encryption is
+needed. Memory that has been swapped out and hence was exported can be
+read from the swap and written to the dump target without need for any
+special actions.
+
+The tweaks / status flags for the exported pages need to be requested
+from the Ultravisor.
+
+**Finalization**
+
+The finalization step will provide the data needed to be able to
+decrypt the vcpu and memory data and end the dump process. When this
+step completes successfully a new dump initiation can be started.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/s390/s390-pv.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/s390/s390-pv.rst
@@ -0,0 +1,116 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=========================================
+s390 (IBM Z) Ultravisor and Protected VMs
+=========================================
+
+Summary
+-------
+Protected virtual machines (PVM) are KVM VMs that do not allow KVM to
+access VM state like guest memory or guest registers. Instead, the
+PVMs are mostly managed by a new entity called Ultravisor (UV). The UV
+provides an API that can be used by PVMs and KVM to request management
+actions.
+
+Each guest starts in non-protected mode and then may make a request to
+transition into protected mode. On transition, KVM registers the guest
+and its VCPUs with the Ultravisor and prepares everything for running
+it.
+
+The Ultravisor will secure and decrypt the guest's boot memory
+(i.e. kernel/initrd). It will safeguard state changes like VCPU
+starts/stops and injected interrupts while the guest is running.
+
+As access to the guest's state, such as the SIE state description, is
+normally needed to be able to run a VM, some changes have been made in
+the behavior of the SIE instruction. A new format 4 state description
+has been introduced, where some fields have different meanings for a
+PVM. SIE exits are minimized as much as possible to improve speed and
+reduce exposed guest state.
+
+
+Interrupt injection
+-------------------
+Interrupt injection is safeguarded by the Ultravisor. As KVM doesn't
+have access to the VCPUs' lowcores, injection is handled via the
+format 4 state description.
+
+Machine check, external, IO and restart interruptions each can be
+injected on SIE entry via a bit in the interrupt injection control
+field (offset 0x54). If the guest cpu is not enabled for the interrupt
+at the time of injection, a validity interception is recognized. The
+format 4 state description contains fields in the interception data
+block where data associated with the interrupt can be transported.
+
+Program and Service Call exceptions have another layer of
+safeguarding; they can only be injected for instructions that have
+been intercepted into KVM. The exceptions need to be a valid outcome
+of an instruction emulation by KVM, e.g. we can never inject a
+addressing exception as they are reported by SIE since KVM has no
+access to the guest memory.
+
+
+Mask notification interceptions
+-------------------------------
+KVM cannot intercept lctl(g) and lpsw(e) anymore in order to be
+notified when a PVM enables a certain class of interrupt.  As a
+replacement, two new interception codes have been introduced: One
+indicating that the contents of CRs 0, 6, or 14 have been changed,
+indicating different interruption subclasses; and one indicating that
+PSW bit 13 has been changed, indicating that a machine check
+intervention was requested and those are now enabled.
+
+Instruction emulation
+---------------------
+With the format 4 state description for PVMs, the SIE instruction already
+interprets more instructions than it does with format 2. It is not able
+to interpret every instruction, but needs to hand some tasks to KVM;
+therefore, the SIE and the ultravisor safeguard emulation inputs and outputs.
+
+The control structures associated with SIE provide the Secure
+Instruction Data Area (SIDA), the Interception Parameters (IP) and the
+Secure Interception General Register Save Area.  Guest GRs and most of
+the instruction data, such as I/O data structures, are filtered.
+Instruction data is copied to and from the SIDA when needed.  Guest
+GRs are put into / retrieved from the Secure Interception General
+Register Save Area.
+
+Only GR values needed to emulate an instruction will be copied into this
+save area and the real register numbers will be hidden.
+
+The Interception Parameters state description field still contains
+the bytes of the instruction text, but with pre-set register values
+instead of the actual ones. I.e. each instruction always uses the same
+instruction text, in order not to leak guest instruction text.
+This also implies that the register content that a guest had in r<n>
+may be in r<m> from the hypervisor's point of view.
+
+The Secure Instruction Data Area contains instruction storage
+data. Instruction data, i.e. data being referenced by an instruction
+like the SCCB for sclp, is moved via the SIDA. When an instruction is
+intercepted, the SIE will only allow data and program interrupts for
+this instruction to be moved to the guest via the two data areas
+discussed before. Other data is either ignored or results in validity
+interceptions.
+
+
+Instruction emulation interceptions
+-----------------------------------
+There are two types of SIE secure instruction intercepts: the normal
+and the notification type. Normal secure instruction intercepts will
+make the guest pending for instruction completion of the intercepted
+instruction type, i.e. on SIE entry it is attempted to complete
+emulation of the instruction with the data provided by KVM. That might
+be a program exception or instruction completion.
+
+The notification type intercepts inform KVM about guest environment
+changes due to guest instruction interpretation. Such an interception
+is recognized, for example, for the store prefix instruction to provide
+the new lowcore location. On SIE reentry, any KVM data in the data areas
+is ignored and execution continues as if the guest instruction had
+completed. For that reason KVM is not allowed to inject a program
+interrupt.
+
+Links
+-----
+`KVM Forum 2019 presentation <https://static.sched.com/hosted_files/kvmforum2019/3b/ibm_protected_vms_s390x.pdf>`_
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/amd-memory-encryption.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/amd-memory-encryption.rst
@@ -0,0 +1,439 @@
+======================================
+Secure Encrypted Virtualization (SEV)
+======================================
+
+Overview
+========
+
+Secure Encrypted Virtualization (SEV) is a feature found on AMD processors.
+
+SEV is an extension to the AMD-V architecture which supports running
+virtual machines (VMs) under the control of a hypervisor. When enabled,
+the memory contents of a VM will be transparently encrypted with a key
+unique to that VM.
+
+The hypervisor can determine the SEV support through the CPUID
+instruction. The CPUID function 0x8000001f reports information related
+to SEV::
+
+	0x8000001f[eax]:
+			Bit[1] 	indicates support for SEV
+	    ...
+		  [ecx]:
+			Bits[31:0]  Number of encrypted guests supported simultaneously
+
+If support for SEV is present, MSR 0xc001_0010 (MSR_AMD64_SYSCFG) and MSR 0xc001_0015
+(MSR_K7_HWCR) can be used to determine if it can be enabled::
+
+	0xc001_0010:
+		Bit[23]	   1 = memory encryption can be enabled
+			   0 = memory encryption can not be enabled
+
+	0xc001_0015:
+		Bit[0]	   1 = memory encryption can be enabled
+			   0 = memory encryption can not be enabled
+
+When SEV support is available, it can be enabled in a specific VM by
+setting the SEV bit before executing VMRUN.::
+
+	VMCB[0x90]:
+		Bit[1]	    1 = SEV is enabled
+			    0 = SEV is disabled
+
+SEV hardware uses ASIDs to associate a memory encryption key with a VM.
+Hence, the ASID for the SEV-enabled guests must be from 1 to a maximum value
+defined in the CPUID 0x8000001f[ecx] field.
+
+SEV Key Management
+==================
+
+The SEV guest key management is handled by a separate processor called the AMD
+Secure Processor (AMD-SP). Firmware running inside the AMD-SP provides a secure
+key management interface to perform common hypervisor activities such as
+encrypting bootstrap code, snapshot, migrating and debugging the guest. For more
+information, see the SEV Key Management spec [api-spec]_
+
+The main ioctl to access SEV is KVM_MEMORY_ENCRYPT_OP.  If the argument
+to KVM_MEMORY_ENCRYPT_OP is NULL, the ioctl returns 0 if SEV is enabled
+and ``ENOTTY` if it is disabled (on some older versions of Linux,
+the ioctl runs normally even with a NULL argument, and therefore will
+likely return ``EFAULT``).  If non-NULL, the argument to KVM_MEMORY_ENCRYPT_OP
+must be a struct kvm_sev_cmd::
+
+       struct kvm_sev_cmd {
+               __u32 id;
+               __u64 data;
+               __u32 error;
+               __u32 sev_fd;
+       };
+
+
+The ``id`` field contains the subcommand, and the ``data`` field points to
+another struct containing arguments specific to command.  The ``sev_fd``
+should point to a file descriptor that is opened on the ``/dev/sev``
+device, if needed (see individual commands).
+
+On output, ``error`` is zero on success, or an error code.  Error codes
+are defined in ``<linux/psp-dev.h>``.
+
+KVM implements the following commands to support common lifecycle events of SEV
+guests, such as launching, running, snapshotting, migrating and decommissioning.
+
+1. KVM_SEV_INIT
+---------------
+
+The KVM_SEV_INIT command is used by the hypervisor to initialize the SEV platform
+context. In a typical workflow, this command should be the first command issued.
+
+Returns: 0 on success, -negative on error
+
+2. KVM_SEV_LAUNCH_START
+-----------------------
+
+The KVM_SEV_LAUNCH_START command is used for creating the memory encryption
+context. To create the encryption context, user must provide a guest policy,
+the owner's public Diffie-Hellman (PDH) key and session information.
+
+Parameters: struct  kvm_sev_launch_start (in/out)
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_start {
+                __u32 handle;           /* if zero then firmware creates a new handle */
+                __u32 policy;           /* guest's policy */
+
+                __u64 dh_uaddr;         /* userspace address pointing to the guest owner's PDH key */
+                __u32 dh_len;
+
+                __u64 session_addr;     /* userspace address which points to the guest session information */
+                __u32 session_len;
+        };
+
+On success, the 'handle' field contains a new handle and on error, a negative value.
+
+KVM_SEV_LAUNCH_START requires the ``sev_fd`` field to be valid.
+
+For more details, see SEV spec Section 6.2.
+
+3. KVM_SEV_LAUNCH_UPDATE_DATA
+-----------------------------
+
+The KVM_SEV_LAUNCH_UPDATE_DATA is used for encrypting a memory region. It also
+calculates a measurement of the memory contents. The measurement is a signature
+of the memory contents that can be sent to the guest owner as an attestation
+that the memory was encrypted correctly by the firmware.
+
+Parameters (in): struct  kvm_sev_launch_update_data
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_update {
+                __u64 uaddr;    /* userspace address to be encrypted (must be 16-byte aligned) */
+                __u32 len;      /* length of the data to be encrypted (must be 16-byte aligned) */
+        };
+
+For more details, see SEV spec Section 6.3.
+
+4. KVM_SEV_LAUNCH_MEASURE
+-------------------------
+
+The KVM_SEV_LAUNCH_MEASURE command is used to retrieve the measurement of the
+data encrypted by the KVM_SEV_LAUNCH_UPDATE_DATA command. The guest owner may
+wait to provide the guest with confidential information until it can verify the
+measurement. Since the guest owner knows the initial contents of the guest at
+boot, the measurement can be verified by comparing it to what the guest owner
+expects.
+
+If len is zero on entry, the measurement blob length is written to len and
+uaddr is unused.
+
+Parameters (in): struct  kvm_sev_launch_measure
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_measure {
+                __u64 uaddr;    /* where to copy the measurement */
+                __u32 len;      /* length of measurement blob */
+        };
+
+For more details on the measurement verification flow, see SEV spec Section 6.4.
+
+5. KVM_SEV_LAUNCH_FINISH
+------------------------
+
+After completion of the launch flow, the KVM_SEV_LAUNCH_FINISH command can be
+issued to make the guest ready for the execution.
+
+Returns: 0 on success, -negative on error
+
+6. KVM_SEV_GUEST_STATUS
+-----------------------
+
+The KVM_SEV_GUEST_STATUS command is used to retrieve status information about a
+SEV-enabled guest.
+
+Parameters (out): struct kvm_sev_guest_status
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_guest_status {
+                __u32 handle;   /* guest handle */
+                __u32 policy;   /* guest policy */
+                __u8 state;     /* guest state (see enum below) */
+        };
+
+SEV guest state:
+
+::
+
+        enum {
+        SEV_STATE_INVALID = 0;
+        SEV_STATE_LAUNCHING,    /* guest is currently being launched */
+        SEV_STATE_SECRET,       /* guest is being launched and ready to accept the ciphertext data */
+        SEV_STATE_RUNNING,      /* guest is fully launched and running */
+        SEV_STATE_RECEIVING,    /* guest is being migrated in from another SEV machine */
+        SEV_STATE_SENDING       /* guest is getting migrated out to another SEV machine */
+        };
+
+7. KVM_SEV_DBG_DECRYPT
+----------------------
+
+The KVM_SEV_DEBUG_DECRYPT command can be used by the hypervisor to request the
+firmware to decrypt the data at the given memory region.
+
+Parameters (in): struct kvm_sev_dbg
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_dbg {
+                __u64 src_uaddr;        /* userspace address of data to decrypt */
+                __u64 dst_uaddr;        /* userspace address of destination */
+                __u32 len;              /* length of memory region to decrypt */
+        };
+
+The command returns an error if the guest policy does not allow debugging.
+
+8. KVM_SEV_DBG_ENCRYPT
+----------------------
+
+The KVM_SEV_DEBUG_ENCRYPT command can be used by the hypervisor to request the
+firmware to encrypt the data at the given memory region.
+
+Parameters (in): struct kvm_sev_dbg
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_dbg {
+                __u64 src_uaddr;        /* userspace address of data to encrypt */
+                __u64 dst_uaddr;        /* userspace address of destination */
+                __u32 len;              /* length of memory region to encrypt */
+        };
+
+The command returns an error if the guest policy does not allow debugging.
+
+9. KVM_SEV_LAUNCH_SECRET
+------------------------
+
+The KVM_SEV_LAUNCH_SECRET command can be used by the hypervisor to inject secret
+data after the measurement has been validated by the guest owner.
+
+Parameters (in): struct kvm_sev_launch_secret
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_secret {
+                __u64 hdr_uaddr;        /* userspace address containing the packet header */
+                __u32 hdr_len;
+
+                __u64 guest_uaddr;      /* the guest memory region where the secret should be injected */
+                __u32 guest_len;
+
+                __u64 trans_uaddr;      /* the hypervisor memory region which contains the secret */
+                __u32 trans_len;
+        };
+
+10. KVM_SEV_GET_ATTESTATION_REPORT
+----------------------------------
+
+The KVM_SEV_GET_ATTESTATION_REPORT command can be used by the hypervisor to query the attestation
+report containing the SHA-256 digest of the guest memory and VMSA passed through the KVM_SEV_LAUNCH
+commands and signed with the PEK. The digest returned by the command should match the digest
+used by the guest owner with the KVM_SEV_LAUNCH_MEASURE.
+
+If len is zero on entry, the measurement blob length is written to len and
+uaddr is unused.
+
+Parameters (in): struct kvm_sev_attestation
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_attestation_report {
+                __u8 mnonce[16];        /* A random mnonce that will be placed in the report */
+
+                __u64 uaddr;            /* userspace address where the report should be copied */
+                __u32 len;
+        };
+
+11. KVM_SEV_SEND_START
+----------------------
+
+The KVM_SEV_SEND_START command can be used by the hypervisor to create an
+outgoing guest encryption context.
+
+If session_len is zero on entry, the length of the guest session information is
+written to session_len and all other fields are not used.
+
+Parameters (in): struct kvm_sev_send_start
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_send_start {
+                __u32 policy;                 /* guest policy */
+
+                __u64 pdh_cert_uaddr;         /* platform Diffie-Hellman certificate */
+                __u32 pdh_cert_len;
+
+                __u64 plat_certs_uaddr;        /* platform certificate chain */
+                __u32 plat_certs_len;
+
+                __u64 amd_certs_uaddr;        /* AMD certificate */
+                __u32 amd_certs_len;
+
+                __u64 session_uaddr;          /* Guest session information */
+                __u32 session_len;
+        };
+
+12. KVM_SEV_SEND_UPDATE_DATA
+----------------------------
+
+The KVM_SEV_SEND_UPDATE_DATA command can be used by the hypervisor to encrypt the
+outgoing guest memory region with the encryption context creating using
+KVM_SEV_SEND_START.
+
+If hdr_len or trans_len are zero on entry, the length of the packet header and
+transport region are written to hdr_len and trans_len respectively, and all
+other fields are not used.
+
+Parameters (in): struct kvm_sev_send_update_data
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_send_update_data {
+                __u64 hdr_uaddr;        /* userspace address containing the packet header */
+                __u32 hdr_len;
+
+                __u64 guest_uaddr;      /* the source memory region to be encrypted */
+                __u32 guest_len;
+
+                __u64 trans_uaddr;      /* the destination memory region  */
+                __u32 trans_len;
+        };
+
+13. KVM_SEV_SEND_FINISH
+------------------------
+
+After completion of the migration flow, the KVM_SEV_SEND_FINISH command can be
+issued by the hypervisor to delete the encryption context.
+
+Returns: 0 on success, -negative on error
+
+14. KVM_SEV_SEND_CANCEL
+------------------------
+
+After completion of SEND_START, but before SEND_FINISH, the source VMM can issue the
+SEND_CANCEL command to stop a migration. This is necessary so that a cancelled
+migration can restart with a new target later.
+
+Returns: 0 on success, -negative on error
+
+15. KVM_SEV_RECEIVE_START
+-------------------------
+
+The KVM_SEV_RECEIVE_START command is used for creating the memory encryption
+context for an incoming SEV guest. To create the encryption context, the user must
+provide a guest policy, the platform public Diffie-Hellman (PDH) key and session
+information.
+
+Parameters: struct  kvm_sev_receive_start (in/out)
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_receive_start {
+                __u32 handle;           /* if zero then firmware creates a new handle */
+                __u32 policy;           /* guest's policy */
+
+                __u64 pdh_uaddr;        /* userspace address pointing to the PDH key */
+                __u32 pdh_len;
+
+                __u64 session_uaddr;    /* userspace address which points to the guest session information */
+                __u32 session_len;
+        };
+
+On success, the 'handle' field contains a new handle and on error, a negative value.
+
+For more details, see SEV spec Section 6.12.
+
+16. KVM_SEV_RECEIVE_UPDATE_DATA
+-------------------------------
+
+The KVM_SEV_RECEIVE_UPDATE_DATA command can be used by the hypervisor to copy
+the incoming buffers into the guest memory region with encryption context
+created during the KVM_SEV_RECEIVE_START.
+
+Parameters (in): struct kvm_sev_receive_update_data
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_receive_update_data {
+                __u64 hdr_uaddr;        /* userspace address containing the packet header */
+                __u32 hdr_len;
+
+                __u64 guest_uaddr;      /* the destination guest memory region */
+                __u32 guest_len;
+
+                __u64 trans_uaddr;      /* the incoming buffer memory region  */
+                __u32 trans_len;
+        };
+
+17. KVM_SEV_RECEIVE_FINISH
+--------------------------
+
+After completion of the migration flow, the KVM_SEV_RECEIVE_FINISH command can be
+issued by the hypervisor to make the guest ready for execution.
+
+Returns: 0 on success, -negative on error
+
+References
+==========
+
+
+See [white-paper]_, [api-spec]_, [amd-apm]_ and [kvm-forum]_ for more info.
+
+.. [white-paper] http://amd-dev.wpengine.netdna-cdn.com/wordpress/media/2013/12/AMD_Memory_Encryption_Whitepaper_v7-Public.pdf
+.. [api-spec] https://support.amd.com/TechDocs/55766_SEV-KM_API_Specification.pdf
+.. [amd-apm] https://support.amd.com/TechDocs/24593.pdf (section 15.34)
+.. [kvm-forum]  https://www.linux-kvm.org/images/7/74/02x08A-Thomas_Lendacky-AMDs_Virtualizatoin_Memory_Encryption_Technology.pdf
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/cpuid.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/cpuid.rst
@@ -0,0 +1,124 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==============
+KVM CPUID bits
+==============
+
+:Author: Glauber Costa <glommer@gmail.com>
+
+A guest running on a kvm host, can check some of its features using
+cpuid. This is not always guaranteed to work, since userspace can
+mask-out some, or even all KVM-related cpuid features before launching
+a guest.
+
+KVM cpuid functions are:
+
+function: KVM_CPUID_SIGNATURE (0x40000000)
+
+returns::
+
+   eax = 0x40000001
+   ebx = 0x4b4d564b
+   ecx = 0x564b4d56
+   edx = 0x4d
+
+Note that this value in ebx, ecx and edx corresponds to the string "KVMKVMKVM".
+The value in eax corresponds to the maximum cpuid function present in this leaf,
+and will be updated if more functions are added in the future.
+Note also that old hosts set eax value to 0x0. This should
+be interpreted as if the value was 0x40000001.
+This function queries the presence of KVM cpuid leafs.
+
+function: define KVM_CPUID_FEATURES (0x40000001)
+
+returns::
+
+          ebx, ecx
+          eax = an OR'ed group of (1 << flag)
+
+where ``flag`` is defined as below:
+
+================================== =========== ================================
+flag                               value       meaning
+================================== =========== ================================
+KVM_FEATURE_CLOCKSOURCE            0           kvmclock available at msrs
+                                               0x11 and 0x12
+
+KVM_FEATURE_NOP_IO_DELAY           1           not necessary to perform delays
+                                               on PIO operations
+
+KVM_FEATURE_MMU_OP                 2           deprecated
+
+KVM_FEATURE_CLOCKSOURCE2           3           kvmclock available at msrs
+                                               0x4b564d00 and 0x4b564d01
+
+KVM_FEATURE_ASYNC_PF               4           async pf can be enabled by
+                                               writing to msr 0x4b564d02
+
+KVM_FEATURE_STEAL_TIME             5           steal time can be enabled by
+                                               writing to msr 0x4b564d03
+
+KVM_FEATURE_PV_EOI                 6           paravirtualized end of interrupt
+                                               handler can be enabled by
+                                               writing to msr 0x4b564d04
+
+KVM_FEATURE_PV_UNHALT              7           guest checks this feature bit
+                                               before enabling paravirtualized
+                                               spinlock support
+
+KVM_FEATURE_PV_TLB_FLUSH           9           guest checks this feature bit
+                                               before enabling paravirtualized
+                                               tlb flush
+
+KVM_FEATURE_ASYNC_PF_VMEXIT        10          paravirtualized async PF VM EXIT
+                                               can be enabled by setting bit 2
+                                               when writing to msr 0x4b564d02
+
+KVM_FEATURE_PV_SEND_IPI            11          guest checks this feature bit
+                                               before enabling paravirtualized
+                                               send IPIs
+
+KVM_FEATURE_POLL_CONTROL           12          host-side polling on HLT can
+                                               be disabled by writing
+                                               to msr 0x4b564d05.
+
+KVM_FEATURE_PV_SCHED_YIELD         13          guest checks this feature bit
+                                               before using paravirtualized
+                                               sched yield.
+
+KVM_FEATURE_ASYNC_PF_INT           14          guest checks this feature bit
+                                               before using the second async
+                                               pf control msr 0x4b564d06 and
+                                               async pf acknowledgment msr
+                                               0x4b564d07.
+
+KVM_FEATURE_MSI_EXT_DEST_ID        15          guest checks this feature bit
+                                               before using extended destination
+                                               ID bits in MSI address bits 11-5.
+
+KVM_FEATURE_HC_MAP_GPA_RANGE       16          guest checks this feature bit before
+                                               using the map gpa range hypercall
+                                               to notify the page state change
+
+KVM_FEATURE_MIGRATION_CONTROL      17          guest checks this feature bit before
+                                               using MSR_KVM_MIGRATION_CONTROL
+
+KVM_FEATURE_CLOCKSOURCE_STABLE_BIT 24          host will warn if no guest-side
+                                               per-cpu warps are expected in
+                                               kvmclock
+================================== =========== ================================
+
+::
+
+      edx = an OR'ed group of (1 << flag)
+
+Where ``flag`` here is defined as below:
+
+================== ============ =================================
+flag               value        meaning
+================== ============ =================================
+KVM_HINTS_REALTIME 0            guest checks this feature bit to
+                                determine that vCPUs are never
+                                preempted for an unlimited time
+                                allowing optimizations
+================== ============ =================================
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/halt-polling.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/halt-polling.rst
@@ -0,0 +1,140 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===========================
+The KVM halt polling system
+===========================
+
+The KVM halt polling system provides a feature within KVM whereby the latency
+of a guest can, under some circumstances, be reduced by polling in the host
+for some time period after the guest has elected to no longer run by cedeing.
+That is, when a guest vcpu has ceded, or in the case of powerpc when all of the
+vcpus of a single vcore have ceded, the host kernel polls for wakeup conditions
+before giving up the cpu to the scheduler in order to let something else run.
+
+Polling provides a latency advantage in cases where the guest can be run again
+very quickly by at least saving us a trip through the scheduler, normally on
+the order of a few micro-seconds, although performance benefits are workload
+dependant. In the event that no wakeup source arrives during the polling
+interval or some other task on the runqueue is runnable the scheduler is
+invoked. Thus halt polling is especially useful on workloads with very short
+wakeup periods where the time spent halt polling is minimised and the time
+savings of not invoking the scheduler are distinguishable.
+
+The generic halt polling code is implemented in:
+
+	virt/kvm/kvm_main.c: kvm_vcpu_block()
+
+The powerpc kvm-hv specific case is implemented in:
+
+	arch/powerpc/kvm/book3s_hv.c: kvmppc_vcore_blocked()
+
+Halt Polling Interval
+=====================
+
+The maximum time for which to poll before invoking the scheduler, referred to
+as the halt polling interval, is increased and decreased based on the perceived
+effectiveness of the polling in an attempt to limit pointless polling.
+This value is stored in either the vcpu struct:
+
+	kvm_vcpu->halt_poll_ns
+
+or in the case of powerpc kvm-hv, in the vcore struct:
+
+	kvmppc_vcore->halt_poll_ns
+
+Thus this is a per vcpu (or vcore) value.
+
+During polling if a wakeup source is received within the halt polling interval,
+the interval is left unchanged. In the event that a wakeup source isn't
+received during the polling interval (and thus schedule is invoked) there are
+two options, either the polling interval and total block time[0] were less than
+the global max polling interval (see module params below), or the total block
+time was greater than the global max polling interval.
+
+In the event that both the polling interval and total block time were less than
+the global max polling interval then the polling interval can be increased in
+the hope that next time during the longer polling interval the wake up source
+will be received while the host is polling and the latency benefits will be
+received. The polling interval is grown in the function grow_halt_poll_ns() and
+is multiplied by the module parameters halt_poll_ns_grow and
+halt_poll_ns_grow_start.
+
+In the event that the total block time was greater than the global max polling
+interval then the host will never poll for long enough (limited by the global
+max) to wakeup during the polling interval so it may as well be shrunk in order
+to avoid pointless polling. The polling interval is shrunk in the function
+shrink_halt_poll_ns() and is divided by the module parameter
+halt_poll_ns_shrink, or set to 0 iff halt_poll_ns_shrink == 0.
+
+It is worth noting that this adjustment process attempts to hone in on some
+steady state polling interval but will only really do a good job for wakeups
+which come at an approximately constant rate, otherwise there will be constant
+adjustment of the polling interval.
+
+[0] total block time:
+		      the time between when the halt polling function is
+		      invoked and a wakeup source received (irrespective of
+		      whether the scheduler is invoked within that function).
+
+Module Parameters
+=================
+
+The kvm module has 3 tuneable module parameters to adjust the global max
+polling interval as well as the rate at which the polling interval is grown and
+shrunk. These variables are defined in include/linux/kvm_host.h and as module
+parameters in virt/kvm/kvm_main.c, or arch/powerpc/kvm/book3s_hv.c in the
+powerpc kvm-hv case.
+
++-----------------------+---------------------------+-------------------------+
+|Module Parameter	|   Description		    |	     Default Value    |
++-----------------------+---------------------------+-------------------------+
+|halt_poll_ns		| The global max polling    | KVM_HALT_POLL_NS_DEFAULT|
+|			| interval which defines    |			      |
+|			| the ceiling value of the  |			      |
+|			| polling interval for      | (per arch value)	      |
+|			| each vcpu.		    |			      |
++-----------------------+---------------------------+-------------------------+
+|halt_poll_ns_grow	| The value by which the    | 2			      |
+|			| halt polling interval is  |			      |
+|			| multiplied in the	    |			      |
+|			| grow_halt_poll_ns()	    |			      |
+|			| function.		    |			      |
++-----------------------+---------------------------+-------------------------+
+|halt_poll_ns_grow_start| The initial value to grow | 10000		      |
+|			| to from zero in the	    |			      |
+|			| grow_halt_poll_ns()	    |			      |
+|			| function.		    |			      |
++-----------------------+---------------------------+-------------------------+
+|halt_poll_ns_shrink	| The value by which the    | 0			      |
+|			| halt polling interval is  |			      |
+|			| divided in the	    |			      |
+|			| shrink_halt_poll_ns()	    |			      |
+|			| function.		    |			      |
++-----------------------+---------------------------+-------------------------+
+
+These module parameters can be set from the debugfs files in:
+
+	/sys/module/kvm/parameters/
+
+Note: that these module parameters are system wide values and are not able to
+      be tuned on a per vm basis.
+
+Further Notes
+=============
+
+- Care should be taken when setting the halt_poll_ns module parameter as a large value
+  has the potential to drive the cpu usage to 100% on a machine which would be almost
+  entirely idle otherwise. This is because even if a guest has wakeups during which very
+  little work is done and which are quite far apart, if the period is shorter than the
+  global max polling interval (halt_poll_ns) then the host will always poll for the
+  entire block time and thus cpu utilisation will go to 100%.
+
+- Halt polling essentially presents a trade off between power usage and latency and
+  the module parameters should be used to tune the affinity for this. Idle cpu time is
+  essentially converted to host kernel time with the aim of decreasing latency when
+  entering the guest.
+
+- Halt polling will only be conducted by the host when no other tasks are runnable on
+  that cpu, otherwise the polling will cease immediately and schedule will be invoked to
+  allow that other task to run. Thus this doesn't allow a guest to denial of service the
+  cpu.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/hypercalls.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/hypercalls.rst
@@ -0,0 +1,192 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===================
+Linux KVM Hypercall
+===================
+
+X86:
+ KVM Hypercalls have a three-byte sequence of either the vmcall or the vmmcall
+ instruction. The hypervisor can replace it with instructions that are
+ guaranteed to be supported.
+
+ Up to four arguments may be passed in rbx, rcx, rdx, and rsi respectively.
+ The hypercall number should be placed in rax and the return value will be
+ placed in rax.  No other registers will be clobbered unless explicitly stated
+ by the particular hypercall.
+
+S390:
+  R2-R7 are used for parameters 1-6. In addition, R1 is used for hypercall
+  number. The return value is written to R2.
+
+  S390 uses diagnose instruction as hypercall (0x500) along with hypercall
+  number in R1.
+
+  For further information on the S390 diagnose call as supported by KVM,
+  refer to Documentation/virt/kvm/s390-diag.rst.
+
+PowerPC:
+  It uses R3-R10 and hypercall number in R11. R4-R11 are used as output registers.
+  Return value is placed in R3.
+
+  KVM hypercalls uses 4 byte opcode, that are patched with 'hypercall-instructions'
+  property inside the device tree's /hypervisor node.
+  For more information refer to Documentation/virt/kvm/ppc-pv.rst
+
+MIPS:
+  KVM hypercalls use the HYPCALL instruction with code 0 and the hypercall
+  number in $2 (v0). Up to four arguments may be placed in $4-$7 (a0-a3) and
+  the return value is placed in $2 (v0).
+
+KVM Hypercalls Documentation
+============================
+
+The template for each hypercall is:
+1. Hypercall name.
+2. Architecture(s)
+3. Status (deprecated, obsolete, active)
+4. Purpose
+
+1. KVM_HC_VAPIC_POLL_IRQ
+------------------------
+
+:Architecture: x86
+:Status: active
+:Purpose: Trigger guest exit so that the host can check for pending
+          interrupts on reentry.
+
+2. KVM_HC_MMU_OP
+----------------
+
+:Architecture: x86
+:Status: deprecated.
+:Purpose: Support MMU operations such as writing to PTE,
+          flushing TLB, release PT.
+
+3. KVM_HC_FEATURES
+------------------
+
+:Architecture: PPC
+:Status: active
+:Purpose: Expose hypercall availability to the guest. On x86 platforms, cpuid
+          used to enumerate which hypercalls are available. On PPC, either
+	  device tree based lookup ( which is also what EPAPR dictates)
+	  OR KVM specific enumeration mechanism (which is this hypercall)
+	  can be used.
+
+4. KVM_HC_PPC_MAP_MAGIC_PAGE
+----------------------------
+
+:Architecture: PPC
+:Status: active
+:Purpose: To enable communication between the hypervisor and guest there is a
+	  shared page that contains parts of supervisor visible register state.
+	  The guest can map this shared page to access its supervisor register
+	  through memory using this hypercall.
+
+5. KVM_HC_KICK_CPU
+------------------
+
+:Architecture: x86
+:Status: active
+:Purpose: Hypercall used to wakeup a vcpu from HLT state
+:Usage example:
+  A vcpu of a paravirtualized guest that is busywaiting in guest
+  kernel mode for an event to occur (ex: a spinlock to become available) can
+  execute HLT instruction once it has busy-waited for more than a threshold
+  time-interval. Execution of HLT instruction would cause the hypervisor to put
+  the vcpu to sleep until occurrence of an appropriate event. Another vcpu of the
+  same guest can wakeup the sleeping vcpu by issuing KVM_HC_KICK_CPU hypercall,
+  specifying APIC ID (a1) of the vcpu to be woken up. An additional argument (a0)
+  is used in the hypercall for future use.
+
+
+6. KVM_HC_CLOCK_PAIRING
+-----------------------
+:Architecture: x86
+:Status: active
+:Purpose: Hypercall used to synchronize host and guest clocks.
+
+Usage:
+
+a0: guest physical address where host copies
+"struct kvm_clock_offset" structure.
+
+a1: clock_type, ATM only KVM_CLOCK_PAIRING_WALLCLOCK (0)
+is supported (corresponding to the host's CLOCK_REALTIME clock).
+
+       ::
+
+		struct kvm_clock_pairing {
+			__s64 sec;
+			__s64 nsec;
+			__u64 tsc;
+			__u32 flags;
+			__u32 pad[9];
+		};
+
+       Where:
+               * sec: seconds from clock_type clock.
+               * nsec: nanoseconds from clock_type clock.
+               * tsc: guest TSC value used to calculate sec/nsec pair
+               * flags: flags, unused (0) at the moment.
+
+The hypercall lets a guest compute a precise timestamp across
+host and guest.  The guest can use the returned TSC value to
+compute the CLOCK_REALTIME for its clock, at the same instant.
+
+Returns KVM_EOPNOTSUPP if the host does not use TSC clocksource,
+or if clock type is different than KVM_CLOCK_PAIRING_WALLCLOCK.
+
+6. KVM_HC_SEND_IPI
+------------------
+
+:Architecture: x86
+:Status: active
+:Purpose: Send IPIs to multiple vCPUs.
+
+- a0: lower part of the bitmap of destination APIC IDs
+- a1: higher part of the bitmap of destination APIC IDs
+- a2: the lowest APIC ID in bitmap
+- a3: APIC ICR
+
+The hypercall lets a guest send multicast IPIs, with at most 128
+128 destinations per hypercall in 64-bit mode and 64 vCPUs per
+hypercall in 32-bit mode.  The destinations are represented by a
+bitmap contained in the first two arguments (a0 and a1). Bit 0 of
+a0 corresponds to the APIC ID in the third argument (a2), bit 1
+corresponds to the APIC ID a2+1, and so on.
+
+Returns the number of CPUs to which the IPIs were delivered successfully.
+
+7. KVM_HC_SCHED_YIELD
+---------------------
+
+:Architecture: x86
+:Status: active
+:Purpose: Hypercall used to yield if the IPI target vCPU is preempted
+
+a0: destination APIC ID
+
+:Usage example: When sending a call-function IPI-many to vCPUs, yield if
+	        any of the IPI target vCPUs was preempted.
+
+8. KVM_HC_MAP_GPA_RANGE
+-------------------------
+:Architecture: x86
+:Status: active
+:Purpose: Request KVM to map a GPA range with the specified attributes.
+
+a0: the guest physical address of the start page
+a1: the number of (4kb) pages (must be contiguous in GPA space)
+a2: attributes
+
+    Where 'attributes' :
+        * bits  3:0 - preferred page size encoding 0 = 4kb, 1 = 2mb, 2 = 1gb, etc...
+        * bit     4 - plaintext = 0, encrypted = 1
+        * bits 63:5 - reserved (must be zero)
+
+**Implementation note**: this hypercall is implemented in userspace via
+the KVM_CAP_EXIT_HYPERCALL capability. Userspace must enable that capability
+before advertising KVM_FEATURE_HC_MAP_GPA_RANGE in the guest CPUID.  In
+addition, if the guest supports KVM_FEATURE_MIGRATION_CONTROL, userspace
+must also set up an MSR filter to process writes to MSR_KVM_MIGRATION_CONTROL.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/index.rst
@@ -0,0 +1,18 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===================
+KVM for x86 systems
+===================
+
+.. toctree::
+   :maxdepth: 2
+
+   amd-memory-encryption
+   cpuid
+   halt-polling
+   hypercalls
+   mmu
+   msr
+   nested-vmx
+   running-nested-guests
+   timekeeping
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/mmu.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/mmu.rst
@@ -0,0 +1,480 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================
+The x86 kvm shadow mmu
+======================
+
+The mmu (in arch/x86/kvm, files mmu.[ch] and paging_tmpl.h) is responsible
+for presenting a standard x86 mmu to the guest, while translating guest
+physical addresses to host physical addresses.
+
+The mmu code attempts to satisfy the following requirements:
+
+- correctness:
+	       the guest should not be able to determine that it is running
+               on an emulated mmu except for timing (we attempt to comply
+               with the specification, not emulate the characteristics of
+               a particular implementation such as tlb size)
+- security:
+	       the guest must not be able to touch host memory not assigned
+               to it
+- performance:
+               minimize the performance penalty imposed by the mmu
+- scaling:
+               need to scale to large memory and large vcpu guests
+- hardware:
+               support the full range of x86 virtualization hardware
+- integration:
+               Linux memory management code must be in control of guest memory
+               so that swapping, page migration, page merging, transparent
+               hugepages, and similar features work without change
+- dirty tracking:
+               report writes to guest memory to enable live migration
+               and framebuffer-based displays
+- footprint:
+               keep the amount of pinned kernel memory low (most memory
+               should be shrinkable)
+- reliability:
+               avoid multipage or GFP_ATOMIC allocations
+
+Acronyms
+========
+
+====  ====================================================================
+pfn   host page frame number
+hpa   host physical address
+hva   host virtual address
+gfn   guest frame number
+gpa   guest physical address
+gva   guest virtual address
+ngpa  nested guest physical address
+ngva  nested guest virtual address
+pte   page table entry (used also to refer generically to paging structure
+      entries)
+gpte  guest pte (referring to gfns)
+spte  shadow pte (referring to pfns)
+tdp   two dimensional paging (vendor neutral term for NPT and EPT)
+====  ====================================================================
+
+Virtual and real hardware supported
+===================================
+
+The mmu supports first-generation mmu hardware, which allows an atomic switch
+of the current paging mode and cr3 during guest entry, as well as
+two-dimensional paging (AMD's NPT and Intel's EPT).  The emulated hardware
+it exposes is the traditional 2/3/4 level x86 mmu, with support for global
+pages, pae, pse, pse36, cr0.wp, and 1GB pages. Emulated hardware also
+able to expose NPT capable hardware on NPT capable hosts.
+
+Translation
+===========
+
+The primary job of the mmu is to program the processor's mmu to translate
+addresses for the guest.  Different translations are required at different
+times:
+
+- when guest paging is disabled, we translate guest physical addresses to
+  host physical addresses (gpa->hpa)
+- when guest paging is enabled, we translate guest virtual addresses, to
+  guest physical addresses, to host physical addresses (gva->gpa->hpa)
+- when the guest launches a guest of its own, we translate nested guest
+  virtual addresses, to nested guest physical addresses, to guest physical
+  addresses, to host physical addresses (ngva->ngpa->gpa->hpa)
+
+The primary challenge is to encode between 1 and 3 translations into hardware
+that support only 1 (traditional) and 2 (tdp) translations.  When the
+number of required translations matches the hardware, the mmu operates in
+direct mode; otherwise it operates in shadow mode (see below).
+
+Memory
+======
+
+Guest memory (gpa) is part of the user address space of the process that is
+using kvm.  Userspace defines the translation between guest addresses and user
+addresses (gpa->hva); note that two gpas may alias to the same hva, but not
+vice versa.
+
+These hvas may be backed using any method available to the host: anonymous
+memory, file backed memory, and device memory.  Memory might be paged by the
+host at any time.
+
+Events
+======
+
+The mmu is driven by events, some from the guest, some from the host.
+
+Guest generated events:
+
+- writes to control registers (especially cr3)
+- invlpg/invlpga instruction execution
+- access to missing or protected translations
+
+Host generated events:
+
+- changes in the gpa->hpa translation (either through gpa->hva changes or
+  through hva->hpa changes)
+- memory pressure (the shrinker)
+
+Shadow pages
+============
+
+The principal data structure is the shadow page, 'struct kvm_mmu_page'.  A
+shadow page contains 512 sptes, which can be either leaf or nonleaf sptes.  A
+shadow page may contain a mix of leaf and nonleaf sptes.
+
+A nonleaf spte allows the hardware mmu to reach the leaf pages and
+is not related to a translation directly.  It points to other shadow pages.
+
+A leaf spte corresponds to either one or two translations encoded into
+one paging structure entry.  These are always the lowest level of the
+translation stack, with optional higher level translations left to NPT/EPT.
+Leaf ptes point at guest pages.
+
+The following table shows translations encoded by leaf ptes, with higher-level
+translations in parentheses:
+
+ Non-nested guests::
+
+  nonpaging:     gpa->hpa
+  paging:        gva->gpa->hpa
+  paging, tdp:   (gva->)gpa->hpa
+
+ Nested guests::
+
+  non-tdp:       ngva->gpa->hpa  (*)
+  tdp:           (ngva->)ngpa->gpa->hpa
+
+  (*) the guest hypervisor will encode the ngva->gpa translation into its page
+      tables if npt is not present
+
+Shadow pages contain the following information:
+  role.level:
+    The level in the shadow paging hierarchy that this shadow page belongs to.
+    1=4k sptes, 2=2M sptes, 3=1G sptes, etc.
+  role.direct:
+    If set, leaf sptes reachable from this page are for a linear range.
+    Examples include real mode translation, large guest pages backed by small
+    host pages, and gpa->hpa translations when NPT or EPT is active.
+    The linear range starts at (gfn << PAGE_SHIFT) and its size is determined
+    by role.level (2MB for first level, 1GB for second level, 0.5TB for third
+    level, 256TB for fourth level)
+    If clear, this page corresponds to a guest page table denoted by the gfn
+    field.
+  role.quadrant:
+    When role.gpte_is_8_bytes=0, the guest uses 32-bit gptes while the host uses 64-bit
+    sptes.  That means a guest page table contains more ptes than the host,
+    so multiple shadow pages are needed to shadow one guest page.
+    For first-level shadow pages, role.quadrant can be 0 or 1 and denotes the
+    first or second 512-gpte block in the guest page table.  For second-level
+    page tables, each 32-bit gpte is converted to two 64-bit sptes
+    (since each first-level guest page is shadowed by two first-level
+    shadow pages) so role.quadrant takes values in the range 0..3.  Each
+    quadrant maps 1GB virtual address space.
+  role.access:
+    Inherited guest access permissions from the parent ptes in the form uwx.
+    Note execute permission is positive, not negative.
+  role.invalid:
+    The page is invalid and should not be used.  It is a root page that is
+    currently pinned (by a cpu hardware register pointing to it); once it is
+    unpinned it will be destroyed.
+  role.gpte_is_8_bytes:
+    Reflects the size of the guest PTE for which the page is valid, i.e. '1'
+    if 64-bit gptes are in use, '0' if 32-bit gptes are in use.
+  role.efer_nx:
+    Contains the value of efer.nx for which the page is valid.
+  role.cr0_wp:
+    Contains the value of cr0.wp for which the page is valid.
+  role.smep_andnot_wp:
+    Contains the value of cr4.smep && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
+  role.smap_andnot_wp:
+    Contains the value of cr4.smap && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
+  role.smm:
+    Is 1 if the page is valid in system management mode.  This field
+    determines which of the kvm_memslots array was used to build this
+    shadow page; it is also used to go back from a struct kvm_mmu_page
+    to a memslot, through the kvm_memslots_for_spte_role macro and
+    __gfn_to_memslot.
+  role.ad_disabled:
+    Is 1 if the MMU instance cannot use A/D bits.  EPT did not have A/D
+    bits before Haswell; shadow EPT page tables also cannot use A/D bits
+    if the L1 hypervisor does not enable them.
+  gfn:
+    Either the guest page table containing the translations shadowed by this
+    page, or the base page frame for linear translations.  See role.direct.
+  spt:
+    A pageful of 64-bit sptes containing the translations for this page.
+    Accessed by both kvm and hardware.
+    The page pointed to by spt will have its page->private pointing back
+    at the shadow page structure.
+    sptes in spt point either at guest pages, or at lower-level shadow pages.
+    Specifically, if sp1 and sp2 are shadow pages, then sp1->spt[n] may point
+    at __pa(sp2->spt).  sp2 will point back at sp1 through parent_pte.
+    The spt array forms a DAG structure with the shadow page as a node, and
+    guest pages as leaves.
+  gfns:
+    An array of 512 guest frame numbers, one for each present pte.  Used to
+    perform a reverse map from a pte to a gfn. When role.direct is set, any
+    element of this array can be calculated from the gfn field when used, in
+    this case, the array of gfns is not allocated. See role.direct and gfn.
+  root_count:
+    A counter keeping track of how many hardware registers (guest cr3 or
+    pdptrs) are now pointing at the page.  While this counter is nonzero, the
+    page cannot be destroyed.  See role.invalid.
+  parent_ptes:
+    The reverse mapping for the pte/ptes pointing at this page's spt. If
+    parent_ptes bit 0 is zero, only one spte points at this page and
+    parent_ptes points at this single spte, otherwise, there exists multiple
+    sptes pointing at this page and (parent_ptes & ~0x1) points at a data
+    structure with a list of parent sptes.
+  unsync:
+    If true, then the translations in this page may not match the guest's
+    translation.  This is equivalent to the state of the tlb when a pte is
+    changed but before the tlb entry is flushed.  Accordingly, unsync ptes
+    are synchronized when the guest executes invlpg or flushes its tlb by
+    other means.  Valid for leaf pages.
+  unsync_children:
+    How many sptes in the page point at pages that are unsync (or have
+    unsynchronized children).
+  unsync_child_bitmap:
+    A bitmap indicating which sptes in spt point (directly or indirectly) at
+    pages that may be unsynchronized.  Used to quickly locate all unsychronized
+    pages reachable from a given page.
+  clear_spte_count:
+    Only present on 32-bit hosts, where a 64-bit spte cannot be written
+    atomically.  The reader uses this while running out of the MMU lock
+    to detect in-progress updates and retry them until the writer has
+    finished the write.
+  write_flooding_count:
+    A guest may write to a page table many times, causing a lot of
+    emulations if the page needs to be write-protected (see "Synchronized
+    and unsynchronized pages" below).  Leaf pages can be unsynchronized
+    so that they do not trigger frequent emulation, but this is not
+    possible for non-leafs.  This field counts the number of emulations
+    since the last time the page table was actually used; if emulation
+    is triggered too frequently on this page, KVM will unmap the page
+    to avoid emulation in the future.
+
+Reverse map
+===========
+
+The mmu maintains a reverse mapping whereby all ptes mapping a page can be
+reached given its gfn.  This is used, for example, when swapping out a page.
+
+Synchronized and unsynchronized pages
+=====================================
+
+The guest uses two events to synchronize its tlb and page tables: tlb flushes
+and page invalidations (invlpg).
+
+A tlb flush means that we need to synchronize all sptes reachable from the
+guest's cr3.  This is expensive, so we keep all guest page tables write
+protected, and synchronize sptes to gptes when a gpte is written.
+
+A special case is when a guest page table is reachable from the current
+guest cr3.  In this case, the guest is obliged to issue an invlpg instruction
+before using the translation.  We take advantage of that by removing write
+protection from the guest page, and allowing the guest to modify it freely.
+We synchronize modified gptes when the guest invokes invlpg.  This reduces
+the amount of emulation we have to do when the guest modifies multiple gptes,
+or when the a guest page is no longer used as a page table and is used for
+random guest data.
+
+As a side effect we have to resynchronize all reachable unsynchronized shadow
+pages on a tlb flush.
+
+
+Reaction to events
+==================
+
+- guest page fault (or npt page fault, or ept violation)
+
+This is the most complicated event.  The cause of a page fault can be:
+
+  - a true guest fault (the guest translation won't allow the access) (*)
+  - access to a missing translation
+  - access to a protected translation
+    - when logging dirty pages, memory is write protected
+    - synchronized shadow pages are write protected (*)
+  - access to untranslatable memory (mmio)
+
+  (*) not applicable in direct mode
+
+Handling a page fault is performed as follows:
+
+ - if the RSV bit of the error code is set, the page fault is caused by guest
+   accessing MMIO and cached MMIO information is available.
+
+   - walk shadow page table
+   - check for valid generation number in the spte (see "Fast invalidation of
+     MMIO sptes" below)
+   - cache the information to vcpu->arch.mmio_gva, vcpu->arch.mmio_access and
+     vcpu->arch.mmio_gfn, and call the emulator
+
+ - If both P bit and R/W bit of error code are set, this could possibly
+   be handled as a "fast page fault" (fixed without taking the MMU lock).  See
+   the description in Documentation/virt/kvm/locking.rst.
+
+ - if needed, walk the guest page tables to determine the guest translation
+   (gva->gpa or ngpa->gpa)
+
+   - if permissions are insufficient, reflect the fault back to the guest
+
+ - determine the host page
+
+   - if this is an mmio request, there is no host page; cache the info to
+     vcpu->arch.mmio_gva, vcpu->arch.mmio_access and vcpu->arch.mmio_gfn
+
+ - walk the shadow page table to find the spte for the translation,
+   instantiating missing intermediate page tables as necessary
+
+   - If this is an mmio request, cache the mmio info to the spte and set some
+     reserved bit on the spte (see callers of kvm_mmu_set_mmio_spte_mask)
+
+ - try to unsynchronize the page
+
+   - if successful, we can let the guest continue and modify the gpte
+
+ - emulate the instruction
+
+   - if failed, unshadow the page and let the guest continue
+
+ - update any translations that were modified by the instruction
+
+invlpg handling:
+
+  - walk the shadow page hierarchy and drop affected translations
+  - try to reinstantiate the indicated translation in the hope that the
+    guest will use it in the near future
+
+Guest control register updates:
+
+- mov to cr3
+
+  - look up new shadow roots
+  - synchronize newly reachable shadow pages
+
+- mov to cr0/cr4/efer
+
+  - set up mmu context for new paging mode
+  - look up new shadow roots
+  - synchronize newly reachable shadow pages
+
+Host translation updates:
+
+  - mmu notifier called with updated hva
+  - look up affected sptes through reverse map
+  - drop (or update) translations
+
+Emulating cr0.wp
+================
+
+If tdp is not enabled, the host must keep cr0.wp=1 so page write protection
+works for the guest kernel, not guest guest userspace.  When the guest
+cr0.wp=1, this does not present a problem.  However when the guest cr0.wp=0,
+we cannot map the permissions for gpte.u=1, gpte.w=0 to any spte (the
+semantics require allowing any guest kernel access plus user read access).
+
+We handle this by mapping the permissions to two possible sptes, depending
+on fault type:
+
+- kernel write fault: spte.u=0, spte.w=1 (allows full kernel access,
+  disallows user access)
+- read fault: spte.u=1, spte.w=0 (allows full read access, disallows kernel
+  write access)
+
+(user write faults generate a #PF)
+
+In the first case there are two additional complications:
+
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+  the kernel may now execute it.  We handle this by also setting spte.nx.
+  If we get a user fetch or read fault, we'll change spte.u=1 and
+  spte.nx=gpte.nx back.  For this to work, KVM forces EFER.NX to 1 when
+  shadow paging is in use.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+  page, it can not be reused when CR4.SMAP is enabled. We set
+  CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+  here we do not care the case that CR4.SMAP is enabled since KVM will
+  directly inject #PF to guest due to failed permission check.
+
+To prevent an spte that was converted into a kernel page with cr0.wp=0
+from being written by the kernel after cr0.wp has changed to 1, we make
+the value of cr0.wp part of the page role.  This means that an spte created
+with one value of cr0.wp cannot be used when cr0.wp has a different value -
+it will simply be missed by the shadow page lookup code.  A similar issue
+exists when an spte created with cr0.wp=0 and cr4.smep=0 is used after
+changing cr4.smep to 1.  To avoid this, the value of !cr0.wp && cr4.smep
+is also made a part of the page role.
+
+Large pages
+===========
+
+The mmu supports all combinations of large and small guest and host pages.
+Supported page sizes include 4k, 2M, 4M, and 1G.  4M pages are treated as
+two separate 2M pages, on both guest and host, since the mmu always uses PAE
+paging.
+
+To instantiate a large spte, four constraints must be satisfied:
+
+- the spte must point to a large host page
+- the guest pte must be a large pte of at least equivalent size (if tdp is
+  enabled, there is no guest pte and this condition is satisfied)
+- if the spte will be writeable, the large page frame may not overlap any
+  write-protected pages
+- the guest page must be wholly contained by a single memory slot
+
+To check the last two conditions, the mmu maintains a ->disallow_lpage set of
+arrays for each memory slot and large page size.  Every write protected page
+causes its disallow_lpage to be incremented, thus preventing instantiation of
+a large spte.  The frames at the end of an unaligned memory slot have
+artificially inflated ->disallow_lpages so they can never be instantiated.
+
+Fast invalidation of MMIO sptes
+===============================
+
+As mentioned in "Reaction to events" above, kvm will cache MMIO
+information in leaf sptes.  When a new memslot is added or an existing
+memslot is changed, this information may become stale and needs to be
+invalidated.  This also needs to hold the MMU lock while walking all
+shadow pages, and is made more scalable with a similar technique.
+
+MMIO sptes have a few spare bits, which are used to store a
+generation number.  The global generation number is stored in
+kvm_memslots(kvm)->generation, and increased whenever guest memory info
+changes.
+
+When KVM finds an MMIO spte, it checks the generation number of the spte.
+If the generation number of the spte does not equal the global generation
+number, it will ignore the cached MMIO information and handle the page
+fault through the slow path.
+
+Since only 18 bits are used to store generation-number on mmio spte, all
+pages are zapped when there is an overflow.
+
+Unfortunately, a single memory access might access kvm_memslots(kvm) multiple
+times, the last one happening when the generation number is retrieved and
+stored into the MMIO spte.  Thus, the MMIO spte might be created based on
+out-of-date information, but with an up-to-date generation number.
+
+To avoid this, the generation number is incremented again after synchronize_srcu
+returns; thus, bit 63 of kvm_memslots(kvm)->generation set to 1 only during a
+memslot update, while some SRCU readers might be using the old copy.  We do not
+want to use an MMIO sptes created with an odd generation number, and we can do
+this without losing a bit in the MMIO spte.  The "update in-progress" bit of the
+generation is not stored in MMIO spte, and is so is implicitly zero when the
+generation is extracted out of the spte.  If KVM is unlucky and creates an MMIO
+spte while an update is in-progress, the next access to the spte will always be
+a cache miss.  For example, a subsequent access during the update window will
+miss due to the in-progress flag diverging, while an access after the update
+window closes will have a higher generation number (as compared to the spte).
+
+
+Further reading
+===============
+
+- NPT presentation from KVM Forum 2008
+  https://www.linux-kvm.org/images/c/c8/KvmForum2008%24kdf2008_21.pdf
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/msr.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/msr.rst
@@ -0,0 +1,391 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=================
+KVM-specific MSRs
+=================
+
+:Author: Glauber Costa <glommer@redhat.com>, Red Hat Inc, 2010
+
+KVM makes use of some custom MSRs to service some requests.
+
+Custom MSRs have a range reserved for them, that goes from
+0x4b564d00 to 0x4b564dff. There are MSRs outside this area,
+but they are deprecated and their use is discouraged.
+
+Custom MSR list
+---------------
+
+The current supported Custom MSR list is:
+
+MSR_KVM_WALL_CLOCK_NEW:
+	0x4b564d00
+
+data:
+	4-byte alignment physical address of a memory area which must be
+	in guest RAM. This memory is expected to hold a copy of the following
+	structure::
+
+	 struct pvclock_wall_clock {
+		u32   version;
+		u32   sec;
+		u32   nsec;
+	  } __attribute__((__packed__));
+
+	whose data will be filled in by the hypervisor. The hypervisor is only
+	guaranteed to update this data at the moment of MSR write.
+	Users that want to reliably query this information more than once have
+	to write more than once to this MSR. Fields have the following meanings:
+
+	version:
+		guest has to check version before and after grabbing
+		time information and check that they are both equal and even.
+		An odd version indicates an in-progress update.
+
+	sec:
+		 number of seconds for wallclock at time of boot.
+
+	nsec:
+		 number of nanoseconds for wallclock at time of boot.
+
+	In order to get the current wallclock time, the system_time from
+	MSR_KVM_SYSTEM_TIME_NEW needs to be added.
+
+	Note that although MSRs are per-CPU entities, the effect of this
+	particular MSR is global.
+
+	Availability of this MSR must be checked via bit 3 in 0x4000001 cpuid
+	leaf prior to usage.
+
+MSR_KVM_SYSTEM_TIME_NEW:
+	0x4b564d01
+
+data:
+	4-byte aligned physical address of a memory area which must be in
+	guest RAM, plus an enable bit in bit 0. This memory is expected to hold
+	a copy of the following structure::
+
+	  struct pvclock_vcpu_time_info {
+		u32   version;
+		u32   pad0;
+		u64   tsc_timestamp;
+		u64   system_time;
+		u32   tsc_to_system_mul;
+		s8    tsc_shift;
+		u8    flags;
+		u8    pad[2];
+	  } __attribute__((__packed__)); /* 32 bytes */
+
+	whose data will be filled in by the hypervisor periodically. Only one
+	write, or registration, is needed for each VCPU. The interval between
+	updates of this structure is arbitrary and implementation-dependent.
+	The hypervisor may update this structure at any time it sees fit until
+	anything with bit0 == 0 is written to it.
+
+	Fields have the following meanings:
+
+	version:
+		guest has to check version before and after grabbing
+		time information and check that they are both equal and even.
+		An odd version indicates an in-progress update.
+
+	tsc_timestamp:
+		the tsc value at the current VCPU at the time
+		of the update of this structure. Guests can subtract this value
+		from current tsc to derive a notion of elapsed time since the
+		structure update.
+
+	system_time:
+		a host notion of monotonic time, including sleep
+		time at the time this structure was last updated. Unit is
+		nanoseconds.
+
+	tsc_to_system_mul:
+		multiplier to be used when converting
+		tsc-related quantity to nanoseconds
+
+	tsc_shift:
+		shift to be used when converting tsc-related
+		quantity to nanoseconds. This shift will ensure that
+		multiplication with tsc_to_system_mul does not overflow.
+		A positive value denotes a left shift, a negative value
+		a right shift.
+
+		The conversion from tsc to nanoseconds involves an additional
+		right shift by 32 bits. With this information, guests can
+		derive per-CPU time by doing::
+
+			time = (current_tsc - tsc_timestamp)
+			if (tsc_shift >= 0)
+				time <<= tsc_shift;
+			else
+				time >>= -tsc_shift;
+			time = (time * tsc_to_system_mul) >> 32
+			time = time + system_time
+
+	flags:
+		bits in this field indicate extended capabilities
+		coordinated between the guest and the hypervisor. Availability
+		of specific flags has to be checked in 0x40000001 cpuid leaf.
+		Current flags are:
+
+
+		+-----------+--------------+----------------------------------+
+		| flag bit  | cpuid bit    | meaning			      |
+		+-----------+--------------+----------------------------------+
+		|	    |		   | time measures taken across       |
+		|    0      |	   24      | multiple cpus are guaranteed to  |
+		|	    |		   | be monotonic		      |
+		+-----------+--------------+----------------------------------+
+		|	    |		   | guest vcpu has been paused by    |
+		|    1	    |	  N/A	   | the host			      |
+		|	    |		   | See 4.70 in api.txt	      |
+		+-----------+--------------+----------------------------------+
+
+	Availability of this MSR must be checked via bit 3 in 0x4000001 cpuid
+	leaf prior to usage.
+
+
+MSR_KVM_WALL_CLOCK:
+	0x11
+
+data and functioning:
+	same as MSR_KVM_WALL_CLOCK_NEW. Use that instead.
+
+	This MSR falls outside the reserved KVM range and may be removed in the
+	future. Its usage is deprecated.
+
+	Availability of this MSR must be checked via bit 0 in 0x4000001 cpuid
+	leaf prior to usage.
+
+MSR_KVM_SYSTEM_TIME:
+	0x12
+
+data and functioning:
+	same as MSR_KVM_SYSTEM_TIME_NEW. Use that instead.
+
+	This MSR falls outside the reserved KVM range and may be removed in the
+	future. Its usage is deprecated.
+
+	Availability of this MSR must be checked via bit 0 in 0x4000001 cpuid
+	leaf prior to usage.
+
+	The suggested algorithm for detecting kvmclock presence is then::
+
+		if (!kvm_para_available())    /* refer to cpuid.txt */
+			return NON_PRESENT;
+
+		flags = cpuid_eax(0x40000001);
+		if (flags & 3) {
+			msr_kvm_system_time = MSR_KVM_SYSTEM_TIME_NEW;
+			msr_kvm_wall_clock = MSR_KVM_WALL_CLOCK_NEW;
+			return PRESENT;
+		} else if (flags & 0) {
+			msr_kvm_system_time = MSR_KVM_SYSTEM_TIME;
+			msr_kvm_wall_clock = MSR_KVM_WALL_CLOCK;
+			return PRESENT;
+		} else
+			return NON_PRESENT;
+
+MSR_KVM_ASYNC_PF_EN:
+	0x4b564d02
+
+data:
+	Asynchronous page fault (APF) control MSR.
+
+	Bits 63-6 hold 64-byte aligned physical address of a 64 byte memory area
+	which must be in guest RAM and must be zeroed. This memory is expected
+	to hold a copy of the following structure::
+
+	  struct kvm_vcpu_pv_apf_data {
+		/* Used for 'page not present' events delivered via #PF */
+		__u32 flags;
+
+		/* Used for 'page ready' events delivered via interrupt notification */
+		__u32 token;
+
+		__u8 pad[56];
+		__u32 enabled;
+	  };
+
+	Bits 5-4 of the MSR are reserved and should be zero. Bit 0 is set to 1
+	when asynchronous page faults are enabled on the vcpu, 0 when disabled.
+	Bit 1 is 1 if asynchronous page faults can be injected when vcpu is in
+	cpl == 0. Bit 2 is 1 if asynchronous page faults are delivered to L1 as
+	#PF vmexits.  Bit 2 can be set only if KVM_FEATURE_ASYNC_PF_VMEXIT is
+	present in CPUID. Bit 3 enables interrupt based delivery of 'page ready'
+	events. Bit 3 can only be set if KVM_FEATURE_ASYNC_PF_INT is present in
+	CPUID.
+
+	'Page not present' events are currently always delivered as synthetic
+	#PF exception. During delivery of these events APF CR2 register contains
+	a token that will be used to notify the guest when missing page becomes
+	available. Also, to make it possible to distinguish between real #PF and
+	APF, first 4 bytes of 64 byte memory location ('flags') will be written
+	to by the hypervisor at the time of injection. Only first bit of 'flags'
+	is currently supported, when set, it indicates that the guest is dealing
+	with asynchronous 'page not present' event. If during a page fault APF
+	'flags' is '0' it means that this is regular page fault. Guest is
+	supposed to clear 'flags' when it is done handling #PF exception so the
+	next event can be delivered.
+
+	Note, since APF 'page not present' events use the same exception vector
+	as regular page fault, guest must reset 'flags' to '0' before it does
+	something that can generate normal page fault.
+
+	Bytes 5-7 of 64 byte memory location ('token') will be written to by the
+	hypervisor at the time of APF 'page ready' event injection. The content
+	of these bytes is a token which was previously delivered as 'page not
+	present' event. The event indicates the page in now available. Guest is
+	supposed to write '0' to 'token' when it is done handling 'page ready'
+	event and to write 1' to MSR_KVM_ASYNC_PF_ACK after clearing the location;
+	writing to the MSR forces KVM to re-scan its queue and deliver the next
+	pending notification.
+
+	Note, MSR_KVM_ASYNC_PF_INT MSR specifying the interrupt vector for 'page
+	ready' APF delivery needs to be written to before enabling APF mechanism
+	in MSR_KVM_ASYNC_PF_EN or interrupt #0 can get injected. The MSR is
+	available if KVM_FEATURE_ASYNC_PF_INT is present in CPUID.
+
+	Note, previously, 'page ready' events were delivered via the same #PF
+	exception as 'page not present' events but this is now deprecated. If
+	bit 3 (interrupt based delivery) is not set APF events are not delivered.
+
+	If APF is disabled while there are outstanding APFs, they will
+	not be delivered.
+
+	Currently 'page ready' APF events will be always delivered on the
+	same vcpu as 'page not present' event was, but guest should not rely on
+	that.
+
+MSR_KVM_STEAL_TIME:
+	0x4b564d03
+
+data:
+	64-byte alignment physical address of a memory area which must be
+	in guest RAM, plus an enable bit in bit 0. This memory is expected to
+	hold a copy of the following structure::
+
+	  struct kvm_steal_time {
+		__u64 steal;
+		__u32 version;
+		__u32 flags;
+		__u8  preempted;
+		__u8  u8_pad[3];
+		__u32 pad[11];
+	  }
+
+	whose data will be filled in by the hypervisor periodically. Only one
+	write, or registration, is needed for each VCPU. The interval between
+	updates of this structure is arbitrary and implementation-dependent.
+	The hypervisor may update this structure at any time it sees fit until
+	anything with bit0 == 0 is written to it. Guest is required to make sure
+	this structure is initialized to zero.
+
+	Fields have the following meanings:
+
+	version:
+		a sequence counter. In other words, guest has to check
+		this field before and after grabbing time information and make
+		sure they are both equal and even. An odd version indicates an
+		in-progress update.
+
+	flags:
+		At this point, always zero. May be used to indicate
+		changes in this structure in the future.
+
+	steal:
+		the amount of time in which this vCPU did not run, in
+		nanoseconds. Time during which the vcpu is idle, will not be
+		reported as steal time.
+
+	preempted:
+		indicate the vCPU who owns this struct is running or
+		not. Non-zero values mean the vCPU has been preempted. Zero
+		means the vCPU is not preempted. NOTE, it is always zero if the
+		the hypervisor doesn't support this field.
+
+MSR_KVM_EOI_EN:
+	0x4b564d04
+
+data:
+	Bit 0 is 1 when PV end of interrupt is enabled on the vcpu; 0
+	when disabled.  Bit 1 is reserved and must be zero.  When PV end of
+	interrupt is enabled (bit 0 set), bits 63-2 hold a 4-byte aligned
+	physical address of a 4 byte memory area which must be in guest RAM and
+	must be zeroed.
+
+	The first, least significant bit of 4 byte memory location will be
+	written to by the hypervisor, typically at the time of interrupt
+	injection.  Value of 1 means that guest can skip writing EOI to the apic
+	(using MSR or MMIO write); instead, it is sufficient to signal
+	EOI by clearing the bit in guest memory - this location will
+	later be polled by the hypervisor.
+	Value of 0 means that the EOI write is required.
+
+	It is always safe for the guest to ignore the optimization and perform
+	the APIC EOI write anyway.
+
+	Hypervisor is guaranteed to only modify this least
+	significant bit while in the current VCPU context, this means that
+	guest does not need to use either lock prefix or memory ordering
+	primitives to synchronise with the hypervisor.
+
+	However, hypervisor can set and clear this memory bit at any time:
+	therefore to make sure hypervisor does not interrupt the
+	guest and clear the least significant bit in the memory area
+	in the window between guest testing it to detect
+	whether it can skip EOI apic write and between guest
+	clearing it to signal EOI to the hypervisor,
+	guest must both read the least significant bit in the memory area and
+	clear it using a single CPU instruction, such as test and clear, or
+	compare and exchange.
+
+MSR_KVM_POLL_CONTROL:
+	0x4b564d05
+
+	Control host-side polling.
+
+data:
+	Bit 0 enables (1) or disables (0) host-side HLT polling logic.
+
+	KVM guests can request the host not to poll on HLT, for example if
+	they are performing polling themselves.
+
+MSR_KVM_ASYNC_PF_INT:
+	0x4b564d06
+
+data:
+	Second asynchronous page fault (APF) control MSR.
+
+	Bits 0-7: APIC vector for delivery of 'page ready' APF events.
+	Bits 8-63: Reserved
+
+	Interrupt vector for asynchnonous 'page ready' notifications delivery.
+	The vector has to be set up before asynchronous page fault mechanism
+	is enabled in MSR_KVM_ASYNC_PF_EN.  The MSR is only available if
+	KVM_FEATURE_ASYNC_PF_INT is present in CPUID.
+
+MSR_KVM_ASYNC_PF_ACK:
+	0x4b564d07
+
+data:
+	Asynchronous page fault (APF) acknowledgment.
+
+	When the guest is done processing 'page ready' APF event and 'token'
+	field in 'struct kvm_vcpu_pv_apf_data' is cleared it is supposed to
+	write '1' to bit 0 of the MSR, this causes the host to re-scan its queue
+	and check if there are more notifications pending. The MSR is available
+	if KVM_FEATURE_ASYNC_PF_INT is present in CPUID.
+
+MSR_KVM_MIGRATION_CONTROL:
+        0x4b564d08
+
+data:
+        This MSR is available if KVM_FEATURE_MIGRATION_CONTROL is present in
+        CPUID.  Bit 0 represents whether live migration of the guest is allowed.
+
+        When a guest is started, bit 0 will be 0 if the guest has encrypted
+        memory and 1 if the guest does not have encrypted memory.  If the
+        guest is communicating page encryption status to the host using the
+        ``KVM_HC_MAP_GPA_RANGE`` hypercall, it can set bit 0 in this MSR to
+        allow live migration of the guest.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/nested-vmx.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/nested-vmx.rst
@@ -0,0 +1,244 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==========
+Nested VMX
+==========
+
+Overview
+---------
+
+On Intel processors, KVM uses Intel's VMX (Virtual-Machine eXtensions)
+to easily and efficiently run guest operating systems. Normally, these guests
+*cannot* themselves be hypervisors running their own guests, because in VMX,
+guests cannot use VMX instructions.
+
+The "Nested VMX" feature adds this missing capability - of running guest
+hypervisors (which use VMX) with their own nested guests. It does so by
+allowing a guest to use VMX instructions, and correctly and efficiently
+emulating them using the single level of VMX available in the hardware.
+
+We describe in much greater detail the theory behind the nested VMX feature,
+its implementation and its performance characteristics, in the OSDI 2010 paper
+"The Turtles Project: Design and Implementation of Nested Virtualization",
+available at:
+
+	https://www.usenix.org/events/osdi10/tech/full_papers/Ben-Yehuda.pdf
+
+
+Terminology
+-----------
+
+Single-level virtualization has two levels - the host (KVM) and the guests.
+In nested virtualization, we have three levels: The host (KVM), which we call
+L0, the guest hypervisor, which we call L1, and its nested guest, which we
+call L2.
+
+
+Running nested VMX
+------------------
+
+The nested VMX feature is enabled by default since Linux kernel v4.20. For
+older Linux kernel, it can be enabled by giving the "nested=1" option to the
+kvm-intel module.
+
+
+No modifications are required to user space (qemu). However, qemu's default
+emulated CPU type (qemu64) does not list the "VMX" CPU feature, so it must be
+explicitly enabled, by giving qemu one of the following options:
+
+     - cpu host              (emulated CPU has all features of the real CPU)
+
+     - cpu qemu64,+vmx       (add just the vmx feature to a named CPU type)
+
+
+ABIs
+----
+
+Nested VMX aims to present a standard and (eventually) fully-functional VMX
+implementation for the a guest hypervisor to use. As such, the official
+specification of the ABI that it provides is Intel's VMX specification,
+namely volume 3B of their "Intel 64 and IA-32 Architectures Software
+Developer's Manual". Not all of VMX's features are currently fully supported,
+but the goal is to eventually support them all, starting with the VMX features
+which are used in practice by popular hypervisors (KVM and others).
+
+As a VMX implementation, nested VMX presents a VMCS structure to L1.
+As mandated by the spec, other than the two fields revision_id and abort,
+this structure is *opaque* to its user, who is not supposed to know or care
+about its internal structure. Rather, the structure is accessed through the
+VMREAD and VMWRITE instructions.
+Still, for debugging purposes, KVM developers might be interested to know the
+internals of this structure; This is struct vmcs12 from arch/x86/kvm/vmx.c.
+
+The name "vmcs12" refers to the VMCS that L1 builds for L2. In the code we
+also have "vmcs01", the VMCS that L0 built for L1, and "vmcs02" is the VMCS
+which L0 builds to actually run L2 - how this is done is explained in the
+aforementioned paper.
+
+For convenience, we repeat the content of struct vmcs12 here. If the internals
+of this structure changes, this can break live migration across KVM versions.
+VMCS12_REVISION (from vmx.c) should be changed if struct vmcs12 or its inner
+struct shadow_vmcs is ever changed.
+
+::
+
+	typedef u64 natural_width;
+	struct __packed vmcs12 {
+		/* According to the Intel spec, a VMCS region must start with
+		 * these two user-visible fields */
+		u32 revision_id;
+		u32 abort;
+
+		u32 launch_state; /* set to 0 by VMCLEAR, to 1 by VMLAUNCH */
+		u32 padding[7]; /* room for future expansion */
+
+		u64 io_bitmap_a;
+		u64 io_bitmap_b;
+		u64 msr_bitmap;
+		u64 vm_exit_msr_store_addr;
+		u64 vm_exit_msr_load_addr;
+		u64 vm_entry_msr_load_addr;
+		u64 tsc_offset;
+		u64 virtual_apic_page_addr;
+		u64 apic_access_addr;
+		u64 ept_pointer;
+		u64 guest_physical_address;
+		u64 vmcs_link_pointer;
+		u64 guest_ia32_debugctl;
+		u64 guest_ia32_pat;
+		u64 guest_ia32_efer;
+		u64 guest_pdptr0;
+		u64 guest_pdptr1;
+		u64 guest_pdptr2;
+		u64 guest_pdptr3;
+		u64 host_ia32_pat;
+		u64 host_ia32_efer;
+		u64 padding64[8]; /* room for future expansion */
+		natural_width cr0_guest_host_mask;
+		natural_width cr4_guest_host_mask;
+		natural_width cr0_read_shadow;
+		natural_width cr4_read_shadow;
+		natural_width dead_space[4]; /* Last remnants of cr3_target_value[0-3]. */
+		natural_width exit_qualification;
+		natural_width guest_linear_address;
+		natural_width guest_cr0;
+		natural_width guest_cr3;
+		natural_width guest_cr4;
+		natural_width guest_es_base;
+		natural_width guest_cs_base;
+		natural_width guest_ss_base;
+		natural_width guest_ds_base;
+		natural_width guest_fs_base;
+		natural_width guest_gs_base;
+		natural_width guest_ldtr_base;
+		natural_width guest_tr_base;
+		natural_width guest_gdtr_base;
+		natural_width guest_idtr_base;
+		natural_width guest_dr7;
+		natural_width guest_rsp;
+		natural_width guest_rip;
+		natural_width guest_rflags;
+		natural_width guest_pending_dbg_exceptions;
+		natural_width guest_sysenter_esp;
+		natural_width guest_sysenter_eip;
+		natural_width host_cr0;
+		natural_width host_cr3;
+		natural_width host_cr4;
+		natural_width host_fs_base;
+		natural_width host_gs_base;
+		natural_width host_tr_base;
+		natural_width host_gdtr_base;
+		natural_width host_idtr_base;
+		natural_width host_ia32_sysenter_esp;
+		natural_width host_ia32_sysenter_eip;
+		natural_width host_rsp;
+		natural_width host_rip;
+		natural_width paddingl[8]; /* room for future expansion */
+		u32 pin_based_vm_exec_control;
+		u32 cpu_based_vm_exec_control;
+		u32 exception_bitmap;
+		u32 page_fault_error_code_mask;
+		u32 page_fault_error_code_match;
+		u32 cr3_target_count;
+		u32 vm_exit_controls;
+		u32 vm_exit_msr_store_count;
+		u32 vm_exit_msr_load_count;
+		u32 vm_entry_controls;
+		u32 vm_entry_msr_load_count;
+		u32 vm_entry_intr_info_field;
+		u32 vm_entry_exception_error_code;
+		u32 vm_entry_instruction_len;
+		u32 tpr_threshold;
+		u32 secondary_vm_exec_control;
+		u32 vm_instruction_error;
+		u32 vm_exit_reason;
+		u32 vm_exit_intr_info;
+		u32 vm_exit_intr_error_code;
+		u32 idt_vectoring_info_field;
+		u32 idt_vectoring_error_code;
+		u32 vm_exit_instruction_len;
+		u32 vmx_instruction_info;
+		u32 guest_es_limit;
+		u32 guest_cs_limit;
+		u32 guest_ss_limit;
+		u32 guest_ds_limit;
+		u32 guest_fs_limit;
+		u32 guest_gs_limit;
+		u32 guest_ldtr_limit;
+		u32 guest_tr_limit;
+		u32 guest_gdtr_limit;
+		u32 guest_idtr_limit;
+		u32 guest_es_ar_bytes;
+		u32 guest_cs_ar_bytes;
+		u32 guest_ss_ar_bytes;
+		u32 guest_ds_ar_bytes;
+		u32 guest_fs_ar_bytes;
+		u32 guest_gs_ar_bytes;
+		u32 guest_ldtr_ar_bytes;
+		u32 guest_tr_ar_bytes;
+		u32 guest_interruptibility_info;
+		u32 guest_activity_state;
+		u32 guest_sysenter_cs;
+		u32 host_ia32_sysenter_cs;
+		u32 padding32[8]; /* room for future expansion */
+		u16 virtual_processor_id;
+		u16 guest_es_selector;
+		u16 guest_cs_selector;
+		u16 guest_ss_selector;
+		u16 guest_ds_selector;
+		u16 guest_fs_selector;
+		u16 guest_gs_selector;
+		u16 guest_ldtr_selector;
+		u16 guest_tr_selector;
+		u16 host_es_selector;
+		u16 host_cs_selector;
+		u16 host_ss_selector;
+		u16 host_ds_selector;
+		u16 host_fs_selector;
+		u16 host_gs_selector;
+		u16 host_tr_selector;
+	};
+
+
+Authors
+-------
+
+These patches were written by:
+    - Abel Gordon, abelg <at> il.ibm.com
+    - Nadav Har'El, nyh <at> il.ibm.com
+    - Orit Wasserman, oritw <at> il.ibm.com
+    - Ben-Ami Yassor, benami <at> il.ibm.com
+    - Muli Ben-Yehuda, muli <at> il.ibm.com
+
+With contributions by:
+    - Anthony Liguori, aliguori <at> us.ibm.com
+    - Mike Day, mdday <at> us.ibm.com
+    - Michael Factor, factor <at> il.ibm.com
+    - Zvi Dubitzky, dubi <at> il.ibm.com
+
+And valuable reviews by:
+    - Avi Kivity, avi <at> redhat.com
+    - Gleb Natapov, gleb <at> redhat.com
+    - Marcelo Tosatti, mtosatti <at> redhat.com
+    - Kevin Tian, kevin.tian <at> intel.com
+    - and others.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/running-nested-guests.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/running-nested-guests.rst
@@ -0,0 +1,276 @@
+==============================
+Running nested guests with KVM
+==============================
+
+A nested guest is the ability to run a guest inside another guest (it
+can be KVM-based or a different hypervisor).  The straightforward
+example is a KVM guest that in turn runs on a KVM guest (the rest of
+this document is built on this example)::
+
+              .----------------.  .----------------.
+              |                |  |                |
+              |      L2        |  |      L2        |
+              | (Nested Guest) |  | (Nested Guest) |
+              |                |  |                |
+              |----------------'--'----------------|
+              |                                    |
+              |       L1 (Guest Hypervisor)        |
+              |          KVM (/dev/kvm)            |
+              |                                    |
+      .------------------------------------------------------.
+      |                 L0 (Host Hypervisor)                 |
+      |                    KVM (/dev/kvm)                    |
+      |------------------------------------------------------|
+      |        Hardware (with virtualization extensions)     |
+      '------------------------------------------------------'
+
+Terminology:
+
+- L0 – level-0; the bare metal host, running KVM
+
+- L1 – level-1 guest; a VM running on L0; also called the "guest
+  hypervisor", as it itself is capable of running KVM.
+
+- L2 – level-2 guest; a VM running on L1, this is the "nested guest"
+
+.. note:: The above diagram is modelled after the x86 architecture;
+          s390x, ppc64 and other architectures are likely to have
+          a different design for nesting.
+
+          For example, s390x always has an LPAR (LogicalPARtition)
+          hypervisor running on bare metal, adding another layer and
+          resulting in at least four levels in a nested setup — L0 (bare
+          metal, running the LPAR hypervisor), L1 (host hypervisor), L2
+          (guest hypervisor), L3 (nested guest).
+
+          This document will stick with the three-level terminology (L0,
+          L1, and L2) for all architectures; and will largely focus on
+          x86.
+
+
+Use Cases
+---------
+
+There are several scenarios where nested KVM can be useful, to name a
+few:
+
+- As a developer, you want to test your software on different operating
+  systems (OSes).  Instead of renting multiple VMs from a Cloud
+  Provider, using nested KVM lets you rent a large enough "guest
+  hypervisor" (level-1 guest).  This in turn allows you to create
+  multiple nested guests (level-2 guests), running different OSes, on
+  which you can develop and test your software.
+
+- Live migration of "guest hypervisors" and their nested guests, for
+  load balancing, disaster recovery, etc.
+
+- VM image creation tools (e.g. ``virt-install``,  etc) often run
+  their own VM, and users expect these to work inside a VM.
+
+- Some OSes use virtualization internally for security (e.g. to let
+  applications run safely in isolation).
+
+
+Enabling "nested" (x86)
+-----------------------
+
+From Linux kernel v4.20 onwards, the ``nested`` KVM parameter is enabled
+by default for Intel and AMD.  (Though your Linux distribution might
+override this default.)
+
+In case you are running a Linux kernel older than v4.19, to enable
+nesting, set the ``nested`` KVM module parameter to ``Y`` or ``1``.  To
+persist this setting across reboots, you can add it in a config file, as
+shown below:
+
+1. On the bare metal host (L0), list the kernel modules and ensure that
+   the KVM modules::
+
+    $ lsmod | grep -i kvm
+    kvm_intel             133627  0
+    kvm                   435079  1 kvm_intel
+
+2. Show information for ``kvm_intel`` module::
+
+    $ modinfo kvm_intel | grep -i nested
+    parm:           nested:bool
+
+3. For the nested KVM configuration to persist across reboots, place the
+   below in ``/etc/modprobed/kvm_intel.conf`` (create the file if it
+   doesn't exist)::
+
+    $ cat /etc/modprobe.d/kvm_intel.conf
+    options kvm-intel nested=y
+
+4. Unload and re-load the KVM Intel module::
+
+    $ sudo rmmod kvm-intel
+    $ sudo modprobe kvm-intel
+
+5. Verify if the ``nested`` parameter for KVM is enabled::
+
+    $ cat /sys/module/kvm_intel/parameters/nested
+    Y
+
+For AMD hosts, the process is the same as above, except that the module
+name is ``kvm-amd``.
+
+
+Additional nested-related kernel parameters (x86)
+-------------------------------------------------
+
+If your hardware is sufficiently advanced (Intel Haswell processor or
+higher, which has newer hardware virt extensions), the following
+additional features will also be enabled by default: "Shadow VMCS
+(Virtual Machine Control Structure)", APIC Virtualization on your bare
+metal host (L0).  Parameters for Intel hosts::
+
+    $ cat /sys/module/kvm_intel/parameters/enable_shadow_vmcs
+    Y
+
+    $ cat /sys/module/kvm_intel/parameters/enable_apicv
+    Y
+
+    $ cat /sys/module/kvm_intel/parameters/ept
+    Y
+
+.. note:: If you suspect your L2 (i.e. nested guest) is running slower,
+          ensure the above are enabled (particularly
+          ``enable_shadow_vmcs`` and ``ept``).
+
+
+Starting a nested guest (x86)
+-----------------------------
+
+Once your bare metal host (L0) is configured for nesting, you should be
+able to start an L1 guest with::
+
+    $ qemu-kvm -cpu host [...]
+
+The above will pass through the host CPU's capabilities as-is to the
+gues); or for better live migration compatibility, use a named CPU
+model supported by QEMU. e.g.::
+
+    $ qemu-kvm -cpu Haswell-noTSX-IBRS,vmx=on
+
+then the guest hypervisor will subsequently be capable of running a
+nested guest with accelerated KVM.
+
+
+Enabling "nested" (s390x)
+-------------------------
+
+1. On the host hypervisor (L0), enable the ``nested`` parameter on
+   s390x::
+
+    $ rmmod kvm
+    $ modprobe kvm nested=1
+
+.. note:: On s390x, the kernel parameter ``hpage`` is mutually exclusive
+          with the ``nested`` paramter — i.e. to be able to enable
+          ``nested``, the ``hpage`` parameter *must* be disabled.
+
+2. The guest hypervisor (L1) must be provided with the ``sie`` CPU
+   feature — with QEMU, this can be done by using "host passthrough"
+   (via the command-line ``-cpu host``).
+
+3. Now the KVM module can be loaded in the L1 (guest hypervisor)::
+
+    $ modprobe kvm
+
+
+Live migration with nested KVM
+------------------------------
+
+Migrating an L1 guest, with a  *live* nested guest in it, to another
+bare metal host, works as of Linux kernel 5.3 and QEMU 4.2.0 for
+Intel x86 systems, and even on older versions for s390x.
+
+On AMD systems, once an L1 guest has started an L2 guest, the L1 guest
+should no longer be migrated or saved (refer to QEMU documentation on
+"savevm"/"loadvm") until the L2 guest shuts down.  Attempting to migrate
+or save-and-load an L1 guest while an L2 guest is running will result in
+undefined behavior.  You might see a ``kernel BUG!`` entry in ``dmesg``, a
+kernel 'oops', or an outright kernel panic.  Such a migrated or loaded L1
+guest can no longer be considered stable or secure, and must be restarted.
+Migrating an L1 guest merely configured to support nesting, while not
+actually running L2 guests, is expected to function normally even on AMD
+systems but may fail once guests are started.
+
+Migrating an L2 guest is always expected to succeed, so all the following
+scenarios should work even on AMD systems:
+
+- Migrating a nested guest (L2) to another L1 guest on the *same* bare
+  metal host.
+
+- Migrating a nested guest (L2) to another L1 guest on a *different*
+  bare metal host.
+
+- Migrating a nested guest (L2) to a bare metal host.
+
+Reporting bugs from nested setups
+-----------------------------------
+
+Debugging "nested" problems can involve sifting through log files across
+L0, L1 and L2; this can result in tedious back-n-forth between the bug
+reporter and the bug fixer.
+
+- Mention that you are in a "nested" setup.  If you are running any kind
+  of "nesting" at all, say so.  Unfortunately, this needs to be called
+  out because when reporting bugs, people tend to forget to even
+  *mention* that they're using nested virtualization.
+
+- Ensure you are actually running KVM on KVM.  Sometimes people do not
+  have KVM enabled for their guest hypervisor (L1), which results in
+  them running with pure emulation or what QEMU calls it as "TCG", but
+  they think they're running nested KVM.  Thus confusing "nested Virt"
+  (which could also mean, QEMU on KVM) with "nested KVM" (KVM on KVM).
+
+Information to collect (generic)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The following is not an exhaustive list, but a very good starting point:
+
+  - Kernel, libvirt, and QEMU version from L0
+
+  - Kernel, libvirt and QEMU version from L1
+
+  - QEMU command-line of L1 -- when using libvirt, you'll find it here:
+    ``/var/log/libvirt/qemu/instance.log``
+
+  - QEMU command-line of L2 -- as above, when using libvirt, get the
+    complete libvirt-generated QEMU command-line
+
+  - ``cat /sys/cpuinfo`` from L0
+
+  - ``cat /sys/cpuinfo`` from L1
+
+  - ``lscpu`` from L0
+
+  - ``lscpu`` from L1
+
+  - Full ``dmesg`` output from L0
+
+  - Full ``dmesg`` output from L1
+
+x86-specific info to collect
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Both the below commands, ``x86info`` and ``dmidecode``, should be
+available on most Linux distributions with the same name:
+
+  - Output of: ``x86info -a`` from L0
+
+  - Output of: ``x86info -a`` from L1
+
+  - Output of: ``dmidecode`` from L0
+
+  - Output of: ``dmidecode`` from L1
+
+s390x-specific info to collect
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Along with the earlier mentioned generic details, the below is
+also recommended:
+
+  - ``/proc/sysinfo`` from L1; this will also include the info from L0
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/virt/kvm/x86/timekeeping.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/virt/kvm/x86/timekeeping.rst
@@ -0,0 +1,645 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================================
+Timekeeping Virtualization for X86-Based Architectures
+======================================================
+
+:Author: Zachary Amsden <zamsden@redhat.com>
+:Copyright: (c) 2010, Red Hat.  All rights reserved.
+
+.. Contents
+
+   1) Overview
+   2) Timing Devices
+   3) TSC Hardware
+   4) Virtualization Problems
+
+1. Overview
+===========
+
+One of the most complicated parts of the X86 platform, and specifically,
+the virtualization of this platform is the plethora of timing devices available
+and the complexity of emulating those devices.  In addition, virtualization of
+time introduces a new set of challenges because it introduces a multiplexed
+division of time beyond the control of the guest CPU.
+
+First, we will describe the various timekeeping hardware available, then
+present some of the problems which arise and solutions available, giving
+specific recommendations for certain classes of KVM guests.
+
+The purpose of this document is to collect data and information relevant to
+timekeeping which may be difficult to find elsewhere, specifically,
+information relevant to KVM and hardware-based virtualization.
+
+2. Timing Devices
+=================
+
+First we discuss the basic hardware devices available.  TSC and the related
+KVM clock are special enough to warrant a full exposition and are described in
+the following section.
+
+2.1. i8254 - PIT
+----------------
+
+One of the first timer devices available is the programmable interrupt timer,
+or PIT.  The PIT has a fixed frequency 1.193182 MHz base clock and three
+channels which can be programmed to deliver periodic or one-shot interrupts.
+These three channels can be configured in different modes and have individual
+counters.  Channel 1 and 2 were not available for general use in the original
+IBM PC, and historically were connected to control RAM refresh and the PC
+speaker.  Now the PIT is typically integrated as part of an emulated chipset
+and a separate physical PIT is not used.
+
+The PIT uses I/O ports 0x40 - 0x43.  Access to the 16-bit counters is done
+using single or multiple byte access to the I/O ports.  There are 6 modes
+available, but not all modes are available to all timers, as only timer 2
+has a connected gate input, required for modes 1 and 5.  The gate line is
+controlled by port 61h, bit 0, as illustrated in the following diagram::
+
+  --------------             ----------------
+  |            |           |                |
+  |  1.1932 MHz|---------->| CLOCK      OUT | ---------> IRQ 0
+  |    Clock   |   |       |                |
+  --------------   |    +->| GATE  TIMER 0  |
+                   |        ----------------
+                   |
+                   |        ----------------
+                   |       |                |
+                   |------>| CLOCK      OUT | ---------> 66.3 KHZ DRAM
+                   |       |                |            (aka /dev/null)
+                   |    +->| GATE  TIMER 1  |
+                   |        ----------------
+                   |
+                   |        ----------------
+                   |       |                |
+                   |------>| CLOCK      OUT | ---------> Port 61h, bit 5
+                           |                |      |
+  Port 61h, bit 0 -------->| GATE  TIMER 2  |       \_.----   ____
+                            ----------------         _|    )--|LPF|---Speaker
+                                                    / *----   \___/
+  Port 61h, bit 1 ---------------------------------/
+
+The timer modes are now described.
+
+Mode 0: Single Timeout.
+ This is a one-shot software timeout that counts down
+ when the gate is high (always true for timers 0 and 1).  When the count
+ reaches zero, the output goes high.
+
+Mode 1: Triggered One-shot.
+ The output is initially set high.  When the gate
+ line is set high, a countdown is initiated (which does not stop if the gate is
+ lowered), during which the output is set low.  When the count reaches zero,
+ the output goes high.
+
+Mode 2: Rate Generator.
+ The output is initially set high.  When the countdown
+ reaches 1, the output goes low for one count and then returns high.  The value
+ is reloaded and the countdown automatically resumes.  If the gate line goes
+ low, the count is halted.  If the output is low when the gate is lowered, the
+ output automatically goes high (this only affects timer 2).
+
+Mode 3: Square Wave.
+ This generates a high / low square wave.  The count
+ determines the length of the pulse, which alternates between high and low
+ when zero is reached.  The count only proceeds when gate is high and is
+ automatically reloaded on reaching zero.  The count is decremented twice at
+ each clock to generate a full high / low cycle at the full periodic rate.
+ If the count is even, the clock remains high for N/2 counts and low for N/2
+ counts; if the clock is odd, the clock is high for (N+1)/2 counts and low
+ for (N-1)/2 counts.  Only even values are latched by the counter, so odd
+ values are not observed when reading.  This is the intended mode for timer 2,
+ which generates sine-like tones by low-pass filtering the square wave output.
+
+Mode 4: Software Strobe.
+ After programming this mode and loading the counter,
+ the output remains high until the counter reaches zero.  Then the output
+ goes low for 1 clock cycle and returns high.  The counter is not reloaded.
+ Counting only occurs when gate is high.
+
+Mode 5: Hardware Strobe.
+ After programming and loading the counter, the
+ output remains high.  When the gate is raised, a countdown is initiated
+ (which does not stop if the gate is lowered).  When the counter reaches zero,
+ the output goes low for 1 clock cycle and then returns high.  The counter is
+ not reloaded.
+
+In addition to normal binary counting, the PIT supports BCD counting.  The
+command port, 0x43 is used to set the counter and mode for each of the three
+timers.
+
+PIT commands, issued to port 0x43, using the following bit encoding::
+
+  Bit 7-4: Command (See table below)
+  Bit 3-1: Mode (000 = Mode 0, 101 = Mode 5, 11X = undefined)
+  Bit 0  : Binary (0) / BCD (1)
+
+Command table::
+
+  0000 - Latch Timer 0 count for port 0x40
+	sample and hold the count to be read in port 0x40;
+	additional commands ignored until counter is read;
+	mode bits ignored.
+
+  0001 - Set Timer 0 LSB mode for port 0x40
+	set timer to read LSB only and force MSB to zero;
+	mode bits set timer mode
+
+  0010 - Set Timer 0 MSB mode for port 0x40
+	set timer to read MSB only and force LSB to zero;
+	mode bits set timer mode
+
+  0011 - Set Timer 0 16-bit mode for port 0x40
+	set timer to read / write LSB first, then MSB;
+	mode bits set timer mode
+
+  0100 - Latch Timer 1 count for port 0x41 - as described above
+  0101 - Set Timer 1 LSB mode for port 0x41 - as described above
+  0110 - Set Timer 1 MSB mode for port 0x41 - as described above
+  0111 - Set Timer 1 16-bit mode for port 0x41 - as described above
+
+  1000 - Latch Timer 2 count for port 0x42 - as described above
+  1001 - Set Timer 2 LSB mode for port 0x42 - as described above
+  1010 - Set Timer 2 MSB mode for port 0x42 - as described above
+  1011 - Set Timer 2 16-bit mode for port 0x42 as described above
+
+  1101 - General counter latch
+	Latch combination of counters into corresponding ports
+	Bit 3 = Counter 2
+	Bit 2 = Counter 1
+	Bit 1 = Counter 0
+	Bit 0 = Unused
+
+  1110 - Latch timer status
+	Latch combination of counter mode into corresponding ports
+	Bit 3 = Counter 2
+	Bit 2 = Counter 1
+	Bit 1 = Counter 0
+
+	The output of ports 0x40-0x42 following this command will be:
+
+	Bit 7 = Output pin
+	Bit 6 = Count loaded (0 if timer has expired)
+	Bit 5-4 = Read / Write mode
+	    01 = MSB only
+	    10 = LSB only
+	    11 = LSB / MSB (16-bit)
+	Bit 3-1 = Mode
+	Bit 0 = Binary (0) / BCD mode (1)
+
+2.2. RTC
+--------
+
+The second device which was available in the original PC was the MC146818 real
+time clock.  The original device is now obsolete, and usually emulated by the
+system chipset, sometimes by an HPET and some frankenstein IRQ routing.
+
+The RTC is accessed through CMOS variables, which uses an index register to
+control which bytes are read.  Since there is only one index register, read
+of the CMOS and read of the RTC require lock protection (in addition, it is
+dangerous to allow userspace utilities such as hwclock to have direct RTC
+access, as they could corrupt kernel reads and writes of CMOS memory).
+
+The RTC generates an interrupt which is usually routed to IRQ 8.  The interrupt
+can function as a periodic timer, an additional once a day alarm, and can issue
+interrupts after an update of the CMOS registers by the MC146818 is complete.
+The type of interrupt is signalled in the RTC status registers.
+
+The RTC will update the current time fields by battery power even while the
+system is off.  The current time fields should not be read while an update is
+in progress, as indicated in the status register.
+
+The clock uses a 32.768kHz crystal, so bits 6-4 of register A should be
+programmed to a 32kHz divider if the RTC is to count seconds.
+
+This is the RAM map originally used for the RTC/CMOS::
+
+  Location    Size    Description
+  ------------------------------------------
+  00h         byte    Current second (BCD)
+  01h         byte    Seconds alarm (BCD)
+  02h         byte    Current minute (BCD)
+  03h         byte    Minutes alarm (BCD)
+  04h         byte    Current hour (BCD)
+  05h         byte    Hours alarm (BCD)
+  06h         byte    Current day of week (BCD)
+  07h         byte    Current day of month (BCD)
+  08h         byte    Current month (BCD)
+  09h         byte    Current year (BCD)
+  0Ah         byte    Register A
+                       bit 7   = Update in progress
+                       bit 6-4 = Divider for clock
+                                  000 = 4.194 MHz
+                                  001 = 1.049 MHz
+                                  010 = 32 kHz
+                                  10X = test modes
+                                  110 = reset / disable
+                                  111 = reset / disable
+                       bit 3-0 = Rate selection for periodic interrupt
+                                  000 = periodic timer disabled
+                                  001 = 3.90625 uS
+                                  010 = 7.8125 uS
+                                  011 = .122070 mS
+                                  100 = .244141 mS
+                                     ...
+                                 1101 = 125 mS
+                                 1110 = 250 mS
+                                 1111 = 500 mS
+  0Bh         byte    Register B
+                       bit 7   = Run (0) / Halt (1)
+                       bit 6   = Periodic interrupt enable
+                       bit 5   = Alarm interrupt enable
+                       bit 4   = Update-ended interrupt enable
+                       bit 3   = Square wave interrupt enable
+                       bit 2   = BCD calendar (0) / Binary (1)
+                       bit 1   = 12-hour mode (0) / 24-hour mode (1)
+                       bit 0   = 0 (DST off) / 1 (DST enabled)
+  OCh         byte    Register C (read only)
+                       bit 7   = interrupt request flag (IRQF)
+                       bit 6   = periodic interrupt flag (PF)
+                       bit 5   = alarm interrupt flag (AF)
+                       bit 4   = update interrupt flag (UF)
+                       bit 3-0 = reserved
+  ODh         byte    Register D (read only)
+                       bit 7   = RTC has power
+                       bit 6-0 = reserved
+  32h         byte    Current century BCD (*)
+  (*) location vendor specific and now determined from ACPI global tables
+
+2.3. APIC
+---------
+
+On Pentium and later processors, an on-board timer is available to each CPU
+as part of the Advanced Programmable Interrupt Controller.  The APIC is
+accessed through memory-mapped registers and provides interrupt service to each
+CPU, used for IPIs and local timer interrupts.
+
+Although in theory the APIC is a safe and stable source for local interrupts,
+in practice, many bugs and glitches have occurred due to the special nature of
+the APIC CPU-local memory-mapped hardware.  Beware that CPU errata may affect
+the use of the APIC and that workarounds may be required.  In addition, some of
+these workarounds pose unique constraints for virtualization - requiring either
+extra overhead incurred from extra reads of memory-mapped I/O or additional
+functionality that may be more computationally expensive to implement.
+
+Since the APIC is documented quite well in the Intel and AMD manuals, we will
+avoid repetition of the detail here.  It should be pointed out that the APIC
+timer is programmed through the LVT (local vector timer) register, is capable
+of one-shot or periodic operation, and is based on the bus clock divided down
+by the programmable divider register.
+
+2.4. HPET
+---------
+
+HPET is quite complex, and was originally intended to replace the PIT / RTC
+support of the X86 PC.  It remains to be seen whether that will be the case, as
+the de facto standard of PC hardware is to emulate these older devices.  Some
+systems designated as legacy free may support only the HPET as a hardware timer
+device.
+
+The HPET spec is rather loose and vague, requiring at least 3 hardware timers,
+but allowing implementation freedom to support many more.  It also imposes no
+fixed rate on the timer frequency, but does impose some extremal values on
+frequency, error and slew.
+
+In general, the HPET is recommended as a high precision (compared to PIT /RTC)
+time source which is independent of local variation (as there is only one HPET
+in any given system).  The HPET is also memory-mapped, and its presence is
+indicated through ACPI tables by the BIOS.
+
+Detailed specification of the HPET is beyond the current scope of this
+document, as it is also very well documented elsewhere.
+
+2.5. Offboard Timers
+--------------------
+
+Several cards, both proprietary (watchdog boards) and commonplace (e1000) have
+timing chips built into the cards which may have registers which are accessible
+to kernel or user drivers.  To the author's knowledge, using these to generate
+a clocksource for a Linux or other kernel has not yet been attempted and is in
+general frowned upon as not playing by the agreed rules of the game.  Such a
+timer device would require additional support to be virtualized properly and is
+not considered important at this time as no known operating system does this.
+
+3. TSC Hardware
+===============
+
+The TSC or time stamp counter is relatively simple in theory; it counts
+instruction cycles issued by the processor, which can be used as a measure of
+time.  In practice, due to a number of problems, it is the most complicated
+timekeeping device to use.
+
+The TSC is represented internally as a 64-bit MSR which can be read with the
+RDMSR, RDTSC, or RDTSCP (when available) instructions.  In the past, hardware
+limitations made it possible to write the TSC, but generally on old hardware it
+was only possible to write the low 32-bits of the 64-bit counter, and the upper
+32-bits of the counter were cleared.  Now, however, on Intel processors family
+0Fh, for models 3, 4 and 6, and family 06h, models e and f, this restriction
+has been lifted and all 64-bits are writable.  On AMD systems, the ability to
+write the TSC MSR is not an architectural guarantee.
+
+The TSC is accessible from CPL-0 and conditionally, for CPL > 0 software by
+means of the CR4.TSD bit, which when enabled, disables CPL > 0 TSC access.
+
+Some vendors have implemented an additional instruction, RDTSCP, which returns
+atomically not just the TSC, but an indicator which corresponds to the
+processor number.  This can be used to index into an array of TSC variables to
+determine offset information in SMP systems where TSCs are not synchronized.
+The presence of this instruction must be determined by consulting CPUID feature
+bits.
+
+Both VMX and SVM provide extension fields in the virtualization hardware which
+allows the guest visible TSC to be offset by a constant.  Newer implementations
+promise to allow the TSC to additionally be scaled, but this hardware is not
+yet widely available.
+
+3.1. TSC synchronization
+------------------------
+
+The TSC is a CPU-local clock in most implementations.  This means, on SMP
+platforms, the TSCs of different CPUs may start at different times depending
+on when the CPUs are powered on.  Generally, CPUs on the same die will share
+the same clock, however, this is not always the case.
+
+The BIOS may attempt to resynchronize the TSCs during the poweron process and
+the operating system or other system software may attempt to do this as well.
+Several hardware limitations make the problem worse - if it is not possible to
+write the full 64-bits of the TSC, it may be impossible to match the TSC in
+newly arriving CPUs to that of the rest of the system, resulting in
+unsynchronized TSCs.  This may be done by BIOS or system software, but in
+practice, getting a perfectly synchronized TSC will not be possible unless all
+values are read from the same clock, which generally only is possible on single
+socket systems or those with special hardware support.
+
+3.2. TSC and CPU hotplug
+------------------------
+
+As touched on already, CPUs which arrive later than the boot time of the system
+may not have a TSC value that is synchronized with the rest of the system.
+Either system software, BIOS, or SMM code may actually try to establish the TSC
+to a value matching the rest of the system, but a perfect match is usually not
+a guarantee.  This can have the effect of bringing a system from a state where
+TSC is synchronized back to a state where TSC synchronization flaws, however
+small, may be exposed to the OS and any virtualization environment.
+
+3.3. TSC and multi-socket / NUMA
+--------------------------------
+
+Multi-socket systems, especially large multi-socket systems are likely to have
+individual clocksources rather than a single, universally distributed clock.
+Since these clocks are driven by different crystals, they will not have
+perfectly matched frequency, and temperature and electrical variations will
+cause the CPU clocks, and thus the TSCs to drift over time.  Depending on the
+exact clock and bus design, the drift may or may not be fixed in absolute
+error, and may accumulate over time.
+
+In addition, very large systems may deliberately slew the clocks of individual
+cores.  This technique, known as spread-spectrum clocking, reduces EMI at the
+clock frequency and harmonics of it, which may be required to pass FCC
+standards for telecommunications and computer equipment.
+
+It is recommended not to trust the TSCs to remain synchronized on NUMA or
+multiple socket systems for these reasons.
+
+3.4. TSC and C-states
+---------------------
+
+C-states, or idling states of the processor, especially C1E and deeper sleep
+states may be problematic for TSC as well.  The TSC may stop advancing in such
+a state, resulting in a TSC which is behind that of other CPUs when execution
+is resumed.  Such CPUs must be detected and flagged by the operating system
+based on CPU and chipset identifications.
+
+The TSC in such a case may be corrected by catching it up to a known external
+clocksource.
+
+3.5. TSC frequency change / P-states
+------------------------------------
+
+To make things slightly more interesting, some CPUs may change frequency.  They
+may or may not run the TSC at the same rate, and because the frequency change
+may be staggered or slewed, at some points in time, the TSC rate may not be
+known other than falling within a range of values.  In this case, the TSC will
+not be a stable time source, and must be calibrated against a known, stable,
+external clock to be a usable source of time.
+
+Whether the TSC runs at a constant rate or scales with the P-state is model
+dependent and must be determined by inspecting CPUID, chipset or vendor
+specific MSR fields.
+
+In addition, some vendors have known bugs where the P-state is actually
+compensated for properly during normal operation, but when the processor is
+inactive, the P-state may be raised temporarily to service cache misses from
+other processors.  In such cases, the TSC on halted CPUs could advance faster
+than that of non-halted processors.  AMD Turion processors are known to have
+this problem.
+
+3.6. TSC and STPCLK / T-states
+------------------------------
+
+External signals given to the processor may also have the effect of stopping
+the TSC.  This is typically done for thermal emergency power control to prevent
+an overheating condition, and typically, there is no way to detect that this
+condition has happened.
+
+3.7. TSC virtualization - VMX
+-----------------------------
+
+VMX provides conditional trapping of RDTSC, RDMSR, WRMSR and RDTSCP
+instructions, which is enough for full virtualization of TSC in any manner.  In
+addition, VMX allows passing through the host TSC plus an additional TSC_OFFSET
+field specified in the VMCS.  Special instructions must be used to read and
+write the VMCS field.
+
+3.8. TSC virtualization - SVM
+-----------------------------
+
+SVM provides conditional trapping of RDTSC, RDMSR, WRMSR and RDTSCP
+instructions, which is enough for full virtualization of TSC in any manner.  In
+addition, SVM allows passing through the host TSC plus an additional offset
+field specified in the SVM control block.
+
+3.9. TSC feature bits in Linux
+------------------------------
+
+In summary, there is no way to guarantee the TSC remains in perfect
+synchronization unless it is explicitly guaranteed by the architecture.  Even
+if so, the TSCs in multi-sockets or NUMA systems may still run independently
+despite being locally consistent.
+
+The following feature bits are used by Linux to signal various TSC attributes,
+but they can only be taken to be meaningful for UP or single node systems.
+
+=========================	=======================================
+X86_FEATURE_TSC			The TSC is available in hardware
+X86_FEATURE_RDTSCP		The RDTSCP instruction is available
+X86_FEATURE_CONSTANT_TSC	The TSC rate is unchanged with P-states
+X86_FEATURE_NONSTOP_TSC		The TSC does not stop in C-states
+X86_FEATURE_TSC_RELIABLE	TSC sync checks are skipped (VMware)
+=========================	=======================================
+
+4. Virtualization Problems
+==========================
+
+Timekeeping is especially problematic for virtualization because a number of
+challenges arise.  The most obvious problem is that time is now shared between
+the host and, potentially, a number of virtual machines.  Thus the virtual
+operating system does not run with 100% usage of the CPU, despite the fact that
+it may very well make that assumption.  It may expect it to remain true to very
+exacting bounds when interrupt sources are disabled, but in reality only its
+virtual interrupt sources are disabled, and the machine may still be preempted
+at any time.  This causes problems as the passage of real time, the injection
+of machine interrupts and the associated clock sources are no longer completely
+synchronized with real time.
+
+This same problem can occur on native hardware to a degree, as SMM mode may
+steal cycles from the naturally on X86 systems when SMM mode is used by the
+BIOS, but not in such an extreme fashion.  However, the fact that SMM mode may
+cause similar problems to virtualization makes it a good justification for
+solving many of these problems on bare metal.
+
+4.1. Interrupt clocking
+-----------------------
+
+One of the most immediate problems that occurs with legacy operating systems
+is that the system timekeeping routines are often designed to keep track of
+time by counting periodic interrupts.  These interrupts may come from the PIT
+or the RTC, but the problem is the same: the host virtualization engine may not
+be able to deliver the proper number of interrupts per second, and so guest
+time may fall behind.  This is especially problematic if a high interrupt rate
+is selected, such as 1000 HZ, which is unfortunately the default for many Linux
+guests.
+
+There are three approaches to solving this problem; first, it may be possible
+to simply ignore it.  Guests which have a separate time source for tracking
+'wall clock' or 'real time' may not need any adjustment of their interrupts to
+maintain proper time.  If this is not sufficient, it may be necessary to inject
+additional interrupts into the guest in order to increase the effective
+interrupt rate.  This approach leads to complications in extreme conditions,
+where host load or guest lag is too much to compensate for, and thus another
+solution to the problem has risen: the guest may need to become aware of lost
+ticks and compensate for them internally.  Although promising in theory, the
+implementation of this policy in Linux has been extremely error prone, and a
+number of buggy variants of lost tick compensation are distributed across
+commonly used Linux systems.
+
+Windows uses periodic RTC clocking as a means of keeping time internally, and
+thus requires interrupt slewing to keep proper time.  It does use a low enough
+rate (ed: is it 18.2 Hz?) however that it has not yet been a problem in
+practice.
+
+4.2. TSC sampling and serialization
+-----------------------------------
+
+As the highest precision time source available, the cycle counter of the CPU
+has aroused much interest from developers.  As explained above, this timer has
+many problems unique to its nature as a local, potentially unstable and
+potentially unsynchronized source.  One issue which is not unique to the TSC,
+but is highlighted because of its very precise nature is sampling delay.  By
+definition, the counter, once read is already old.  However, it is also
+possible for the counter to be read ahead of the actual use of the result.
+This is a consequence of the superscalar execution of the instruction stream,
+which may execute instructions out of order.  Such execution is called
+non-serialized.  Forcing serialized execution is necessary for precise
+measurement with the TSC, and requires a serializing instruction, such as CPUID
+or an MSR read.
+
+Since CPUID may actually be virtualized by a trap and emulate mechanism, this
+serialization can pose a performance issue for hardware virtualization.  An
+accurate time stamp counter reading may therefore not always be available, and
+it may be necessary for an implementation to guard against "backwards" reads of
+the TSC as seen from other CPUs, even in an otherwise perfectly synchronized
+system.
+
+4.3. Timespec aliasing
+----------------------
+
+Additionally, this lack of serialization from the TSC poses another challenge
+when using results of the TSC when measured against another time source.  As
+the TSC is much higher precision, many possible values of the TSC may be read
+while another clock is still expressing the same value.
+
+That is, you may read (T,T+10) while external clock C maintains the same value.
+Due to non-serialized reads, you may actually end up with a range which
+fluctuates - from (T-1.. T+10).  Thus, any time calculated from a TSC, but
+calibrated against an external value may have a range of valid values.
+Re-calibrating this computation may actually cause time, as computed after the
+calibration, to go backwards, compared with time computed before the
+calibration.
+
+This problem is particularly pronounced with an internal time source in Linux,
+the kernel time, which is expressed in the theoretically high resolution
+timespec - but which advances in much larger granularity intervals, sometimes
+at the rate of jiffies, and possibly in catchup modes, at a much larger step.
+
+This aliasing requires care in the computation and recalibration of kvmclock
+and any other values derived from TSC computation (such as TSC virtualization
+itself).
+
+4.4. Migration
+--------------
+
+Migration of a virtual machine raises problems for timekeeping in two ways.
+First, the migration itself may take time, during which interrupts cannot be
+delivered, and after which, the guest time may need to be caught up.  NTP may
+be able to help to some degree here, as the clock correction required is
+typically small enough to fall in the NTP-correctable window.
+
+An additional concern is that timers based off the TSC (or HPET, if the raw bus
+clock is exposed) may now be running at different rates, requiring compensation
+in some way in the hypervisor by virtualizing these timers.  In addition,
+migrating to a faster machine may preclude the use of a passthrough TSC, as a
+faster clock cannot be made visible to a guest without the potential of time
+advancing faster than usual.  A slower clock is less of a problem, as it can
+always be caught up to the original rate.  KVM clock avoids these problems by
+simply storing multipliers and offsets against the TSC for the guest to convert
+back into nanosecond resolution values.
+
+4.5. Scheduling
+---------------
+
+Since scheduling may be based on precise timing and firing of interrupts, the
+scheduling algorithms of an operating system may be adversely affected by
+virtualization.  In theory, the effect is random and should be universally
+distributed, but in contrived as well as real scenarios (guest device access,
+causes of virtualization exits, possible context switch), this may not always
+be the case.  The effect of this has not been well studied.
+
+In an attempt to work around this, several implementations have provided a
+paravirtualized scheduler clock, which reveals the true amount of CPU time for
+which a virtual machine has been running.
+
+4.6. Watchdogs
+--------------
+
+Watchdog timers, such as the lock detector in Linux may fire accidentally when
+running under hardware virtualization due to timer interrupts being delayed or
+misinterpretation of the passage of real time.  Usually, these warnings are
+spurious and can be ignored, but in some circumstances it may be necessary to
+disable such detection.
+
+4.7. Delays and precision timing
+--------------------------------
+
+Precise timing and delays may not be possible in a virtualized system.  This
+can happen if the system is controlling physical hardware, or issues delays to
+compensate for slower I/O to and from devices.  The first issue is not solvable
+in general for a virtualized system; hardware control software can't be
+adequately virtualized without a full real-time operating system, which would
+require an RT aware virtualization platform.
+
+The second issue may cause performance problems, but this is unlikely to be a
+significant issue.  In many cases these delays may be eliminated through
+configuration or paravirtualization.
+
+4.8. Covert channels and leaks
+------------------------------
+
+In addition to the above problems, time information will inevitably leak to the
+guest about the host in anything but a perfect implementation of virtualized
+time.  This may allow the guest to infer the presence of a hypervisor (as in a
+red-pill type detection), and it may allow information to leak between guests
+by using CPU utilization itself as a signalling channel.  Preventing such
+problems would require completely isolated virtual time which may not track
+real time any longer.  This may be useful in certain security or QA contexts,
+but in general isn't recommended for real-world deployment scenarios.
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/x86/index.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/x86/index.rst
@@ -37,3 +37,4 @@
    sgx
    features
    elf_auxvec
+   xstate
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/x86/mds.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/x86/mds.rst
@@ -95,6 +95,9 @@
 
     mds_clear_cpu_buffers()
 
+Also macro CLEAR_CPU_BUFFERS can be used in ASM late in exit-to-user path.
+Other than CFLAGS.ZF, this macro doesn't clobber any registers.
+
 The mitigation is invoked on kernel/userspace, hypervisor/guest and C-state
 (idle) transitions.
 
@@ -138,17 +141,30 @@
 
    When transitioning from kernel to user space the CPU buffers are flushed
    on affected CPUs when the mitigation is not disabled on the kernel
-   command line. The migitation is enabled through the static key
-   mds_user_clear.
+   command line. The mitigation is enabled through the feature flag
+   X86_FEATURE_CLEAR_CPU_BUF.
 
-   The mitigation is invoked in prepare_exit_to_usermode() which covers
-   all but one of the kernel to user space transitions.  The exception
-   is when we return from a Non Maskable Interrupt (NMI), which is
-   handled directly in do_nmi().
-
-   (The reason that NMI is special is that prepare_exit_to_usermode() can
-    enable IRQs.  In NMI context, NMIs are blocked, and we don't want to
-    enable IRQs with NMIs blocked.)
+   The mitigation is invoked just before transitioning to userspace after
+   user registers are restored. This is done to minimize the window in
+   which kernel data could be accessed after VERW e.g. via an NMI after
+   VERW.
+
+   **Corner case not handled**
+   Interrupts returning to kernel don't clear CPUs buffers since the
+   exit-to-user path is expected to do that anyways. But, there could be
+   a case when an NMI is generated in kernel after the exit-to-user path
+   has cleared the buffers. This case is not handled and NMI returning to
+   kernel don't clear CPU buffers because:
+
+   1. It is rare to get an NMI after VERW, but before returning to userspace.
+   2. For an unprivileged user, there is no known way to make that NMI
+      less rare or target it.
+   3. It would take a large number of these precisely-timed NMIs to mount
+      an actual attack.  There's presumably not enough bandwidth.
+   4. The NMI in question occurs after a VERW, i.e. when user state is
+      restored and most interesting data is already scrubbed. Whats left
+      is only the data that NMI touches, and that may or may not be of
+      any interest.
 
 
 2. C-State transition
--- linux-xilinx-zynqmp-5.15.0.orig/Documentation/x86/xstate.rst
+++ linux-xilinx-zynqmp-5.15.0/Documentation/x86/xstate.rst
@@ -0,0 +1,65 @@
+Using XSTATE features in user space applications
+================================================
+
+The x86 architecture supports floating-point extensions which are
+enumerated via CPUID. Applications consult CPUID and use XGETBV to
+evaluate which features have been enabled by the kernel XCR0.
+
+Up to AVX-512 and PKRU states, these features are automatically enabled by
+the kernel if available. Features like AMX TILE_DATA (XSTATE component 18)
+are enabled by XCR0 as well, but the first use of related instruction is
+trapped by the kernel because by default the required large XSTATE buffers
+are not allocated automatically.
+
+Using dynamically enabled XSTATE features in user space applications
+--------------------------------------------------------------------
+
+The kernel provides an arch_prctl(2) based mechanism for applications to
+request the usage of such features. The arch_prctl(2) options related to
+this are:
+
+-ARCH_GET_XCOMP_SUPP
+
+ arch_prctl(ARCH_GET_XCOMP_SUPP, &features);
+
+ ARCH_GET_XCOMP_SUPP stores the supported features in userspace storage of
+ type uint64_t. The second argument is a pointer to that storage.
+
+-ARCH_GET_XCOMP_PERM
+
+ arch_prctl(ARCH_GET_XCOMP_PERM, &features);
+
+ ARCH_GET_XCOMP_PERM stores the features for which the userspace process
+ has permission in userspace storage of type uint64_t. The second argument
+ is a pointer to that storage.
+
+-ARCH_REQ_XCOMP_PERM
+
+ arch_prctl(ARCH_REQ_XCOMP_PERM, feature_nr);
+
+ ARCH_REQ_XCOMP_PERM allows to request permission for a dynamically enabled
+ feature or a feature set. A feature set can be mapped to a facility, e.g.
+ AMX, and can require one or more XSTATE components to be enabled.
+
+ The feature argument is the number of the highest XSTATE component which
+ is required for a facility to work.
+
+When requesting permission for a feature, the kernel checks the
+availability. The kernel ensures that sigaltstacks in the process's tasks
+are large enough to accommodate the resulting large signal frame. It
+enforces this both during ARCH_REQ_XCOMP_SUPP and during any subsequent
+sigaltstack(2) calls. If an installed sigaltstack is smaller than the
+resulting sigframe size, ARCH_REQ_XCOMP_SUPP results in -ENOSUPP. Also,
+sigaltstack(2) results in -ENOMEM if the requested altstack is too small
+for the permitted features.
+
+Permission, when granted, is valid per process. Permissions are inherited
+on fork(2) and cleared on exec(3).
+
+The first use of an instruction related to a dynamically enabled feature is
+trapped by the kernel. The trap handler checks whether the process has
+permission to use the feature. If the process has no permission then the
+kernel sends SIGILL to the application. If the process has permission then
+the handler allocates a larger xstate buffer for the task so the large
+state can be context switched. In the unlikely cases that the allocation
+fails, the kernel sends SIGSEGV.
--- linux-xilinx-zynqmp-5.15.0.orig/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/Kconfig
@@ -19,6 +19,8 @@
 
 source "drivers/Kconfig"
 
+source "ubuntu/Kconfig"
+
 source "fs/Kconfig"
 
 source "security/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/MAINTAINERS
+++ linux-xilinx-zynqmp-5.15.0/MAINTAINERS
@@ -257,6 +257,18 @@
 F:	Documentation/scsi/aacraid.rst
 F:	drivers/scsi/aacraid/
 
+AAEON DEVICE DRIVER WITH WMI INTERFACE
+M:	Edward Lin<edward1_lin@asus.com>
+M:	Kunyang Fan <kunyang_fan@asus.com>
+M:	Frank Hsieh <frank2_hsieh@asus.com>
+M:	Jacob Wu <jacob_wu@asus.com>
+S:	Supported
+F:	drivers/gpio/gpio-aaeon.c
+F:	drivers/hwmon/hwmon-aaeon.c
+F:	drivers/leds/leds-aaeon.c
+F:	drivers/mfd/mfd-aaeon.c
+F:	drivers/watchdog/wdt_aaeon.c
+
 ABI/API
 L:	linux-api@vger.kernel.org
 F:	include/linux/syscalls.h
@@ -395,11 +407,11 @@
 S:	Maintained
 F:	drivers/acpi/arm64
 
-ACPI I2C MULTI INSTANTIATE DRIVER
+ACPI SERIAL MULTI INSTANTIATE DRIVER
 M:	Hans de Goede <hdegoede@redhat.com>
 L:	platform-driver-x86@vger.kernel.org
 S:	Maintained
-F:	drivers/platform/x86/i2c-multi-instantiate.c
+F:	drivers/platform/x86/serial-multi-instantiate.c
 
 ACPI PMIC DRIVERS
 M:	"Rafael J. Wysocki" <rafael@kernel.org>
@@ -434,6 +446,7 @@
 M:	Jean-Philippe Brucker <jean-philippe@linaro.org>
 L:	linux-acpi@vger.kernel.org
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Maintained
 F:	drivers/acpi/viot.c
 F:	include/linux/acpi_viot.h
@@ -884,6 +897,14 @@
 F:	drivers/infiniband/hw/efa/
 F:	include/uapi/rdma/efa-abi.h
 
+AMD AXI W1 DRIVER
+M:	Kris Chaplin <kris.chaplin@amd.com>
+R:	Thomas Delev <thomas.delev@amd.com>
+R:	Michal Simek <michal.simek@amd.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/w1/amd,axi-1wire-host.yaml
+F:	drivers/w1/masters/amd_axi_w1.c
+
 AMD CRYPTOGRAPHIC COPROCESSOR (CCP) DRIVER
 M:	Tom Lendacky <thomas.lendacky@amd.com>
 M:	John Allen <john.allen@amd.com>
@@ -941,6 +962,7 @@
 M:	Joerg Roedel <joro@8bytes.org>
 R:	Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu.git
 F:	drivers/iommu/amd/
@@ -991,6 +1013,13 @@
 S:	Maintained
 F:	drivers/dma/ptdma/
 
+AMD PSTATE DRIVER
+M:	Huang Rui <ray.huang@amd.com>
+L:	linux-pm@vger.kernel.org
+S:	Supported
+F:	Documentation/admin-guide/pm/amd-pstate.rst
+F:	drivers/cpufreq/amd-pstate*
+
 AMD SEATTLE DEVICE TREE SUPPORT
 M:	Brijesh Singh <brijeshkumar.singh@amd.com>
 M:	Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
@@ -1248,7 +1277,7 @@
 M:	William Breathitt Gray <vilhelm.gray@gmail.com>
 L:	linux-iio@vger.kernel.org
 S:	Maintained
-F:	drivers/iio/adc/stx104.c
+F:	drivers/iio/addac/stx104.c
 
 APM DRIVER
 M:	Jiri Kosina <jikos@kernel.org>
@@ -1336,6 +1365,12 @@
 S:	Maintained
 F:	drivers/media/i2c/aptina-pll.*
 
+AR1335 ON SEMICONDUCTOR CAMERA SENSOR DRIVER
+M:      Anil Kumar M <anil.mamidala@amd.com>
+S:      Maintained
+F:      Documentation/devicetree/bindings/media/i2c/onnn,ar1335.yaml
+F:      drivers/media/i2c/ar1335.c
+
 AQUACOMPUTER D5 NEXT PUMP SENSOR DRIVER
 M:	Aleksa Savic <savicaleksa83@gmail.com>
 L:	linux-hwmon@vger.kernel.org
@@ -3064,8 +3099,11 @@
 ATMEL MACB ETHERNET DRIVER
 M:	Nicolas Ferre <nicolas.ferre@microchip.com>
 M:	Claudiu Beznea <claudiu.beznea@microchip.com>
+R:	Harini Katakam <harini.katakam@xilinx.com>
+L:	git@xilinx.com
 S:	Supported
 F:	drivers/net/ethernet/cadence/
+W:	https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841740/Macb+Driver
 
 ATMEL MAXTOUCH DRIVER
 M:	Nick Dyer <nick@shmanahar.org>
@@ -3112,7 +3150,7 @@
 AUDIT SUBSYSTEM
 M:	Paul Moore <paul@paul-moore.com>
 M:	Eric Paris <eparis@redhat.com>
-L:	linux-audit@redhat.com (moderated for non-subscribers)
+L:	audit@vger.kernel.org
 S:	Supported
 W:	https://github.com/linux-audit
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit.git
@@ -3122,6 +3160,19 @@
 F:	kernel/audit*
 F:	lib/*audit.c
 
+AUFS (advanced multi layered unification filesystem) FILESYSTEM
+M:	"J. R. Okajima" <hooanon05g@gmail.com>
+L:	aufs-users@lists.sourceforge.net (members only)
+L:	linux-unionfs@vger.kernel.org
+S:	Supported
+W:	http://aufs.sourceforge.net
+T:	git://github.com/sfjro/aufs4-linux.git
+F:	Documentation/ABI/testing/debugfs-aufs
+F:	Documentation/ABI/testing/sysfs-aufs
+F:	Documentation/filesystems/aufs/
+F:	fs/aufs/
+F:	include/uapi/linux/aufs_type.h
+
 AUXILIARY DISPLAY DRIVERS
 M:	Miguel Ojeda <ojeda@kernel.org>
 S:	Maintained
@@ -3405,6 +3456,8 @@
 F:	net/sched/cls_bpf.c
 F:	samples/bpf/
 F:	scripts/bpf_doc.py
+F:	scripts/pahole-flags.sh
+F:	scripts/pahole-version.sh
 F:	tools/bpf/
 F:	tools/lib/bpf/
 F:	tools/testing/selftests/bpf/
@@ -4068,6 +4121,13 @@
 F:	Documentation/filesystems/caching/cachefiles.rst
 F:	fs/cachefiles/
 
+CADENCE I2C DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+R:	Venkata Visweswarachari Mallavarapu <vmallava@xilinx.com>
+L:	git@xilinx.com
+F:	drivers/i2c/busses/i2c-cadence.c
+W:	https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842160/Cadence+I2C+Driver
+
 CADENCE MIPI-CSI2 BRIDGES
 M:	Maxime Ripard <mripard@kernel.org>
 L:	linux-media@vger.kernel.org
@@ -4371,6 +4431,15 @@
 X:	drivers/char/random.c
 X:	drivers/char/tpm/
 
+CHAR and MISC XILINX AI ENGINE DRIVER
+M:	Wendy Liang <wendy.liang@xilinx.com>
+M:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/soc/xilinx/xlnx,ai-engine.yaml
+F:	drivers/misc/xilinx-ai-engine/
+F:	include/linux/xlnx-ai-engine.h
+F:	include/uapi/linux/xlnx-ai-engine.h
+
 CHECKPATCH
 M:	Andy Whitcroft <apw@canonical.com>
 M:	Joe Perches <joe@perches.com>
@@ -4393,6 +4462,7 @@
 
 CHIPIDEA USB HIGH SPEED DUAL ROLE CONTROLLER
 M:	Peter Chen <peter.chen@kernel.org>
+R:	Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git
@@ -4446,9 +4516,12 @@
 CIRRUS LOGIC AUDIO CODEC DRIVERS
 M:	James Schulman <james.schulman@cirrus.com>
 M:	David Rhodes <david.rhodes@cirrus.com>
+M:	Lucas Tanure <tanureal@opensource.cirrus.com>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 L:	patches@opensource.cirrus.com
 S:	Maintained
+F:	Documentation/devicetree/bindings/sound/cirrus,cs*
+F:	sound/pci/hda/cs*
 F:	sound/soc/codecs/cs*
 
 CIRRUS LOGIC EP93XX ETHERNET DRIVER
@@ -4663,6 +4736,7 @@
 F:	Documentation/admin-guide/cifs/
 F:	fs/cifs/
 F:	fs/smbfs_common/
+F:	include/uapi/linux/cifs
 
 COMPACTPCI HOTPLUG CORE
 M:	Scott Murray <scott@spiteful.org>
@@ -4810,7 +4884,6 @@
 F:	Documentation/driver-api/generic-counter.rst
 F:	drivers/counter/
 F:	include/linux/counter.h
-F:	include/linux/counter_enum.h
 
 CP2615 I2C DRIVER
 M:	Bence Csókás <bence98@sch.bme.hu>
@@ -5203,13 +5276,6 @@
 F:	include/uapi/linux/dccp.h
 F:	net/dccp/
 
-DECnet NETWORK LAYER
-L:	linux-decnet-user@lists.sourceforge.net
-S:	Orphan
-W:	http://linux-decnet.sourceforge.net
-F:	Documentation/networking/decnet.rst
-F:	net/decnet/
-
 DECSTATION PLATFORM SUPPORT
 M:	"Maciej W. Rozycki" <macro@orcam.me.uk>
 L:	linux-mips@vger.kernel.org
@@ -5363,6 +5429,7 @@
 
 DESIGNWARE USB3 DRD IP DRIVER
 M:	Felipe Balbi <balbi@kernel.org>
+R:	Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git
@@ -5602,6 +5669,7 @@
 M:	Marek Szyprowski <m.szyprowski@samsung.com>
 R:	Robin Murphy <robin.murphy@arm.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Supported
 W:	http://git.infradead.org/users/hch/dma-mapping.git
 T:	git git://git.infradead.org/users/hch/dma-mapping.git
@@ -5614,6 +5682,7 @@
 DMA MAPPING BENCHMARK
 M:	Barry Song <song.bao.hua@hisilicon.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 F:	kernel/dma/map_benchmark.c
 F:	tools/testing/selftests/dma/
 
@@ -7024,7 +7093,6 @@
 F:	drivers/net/mdio/of_mdio.c
 F:	drivers/net/pcs/
 F:	drivers/net/phy/
-F:	drivers/of/of_net.c
 F:	include/dt-bindings/net/qca-ar803x.h
 F:	include/linux/*mdio*.h
 F:	include/linux/mdio/*.h
@@ -7036,6 +7104,7 @@
 F:	include/trace/events/mdio.h
 F:	include/uapi/linux/mdio.h
 F:	include/uapi/linux/mii.h
+F:	net/core/of_net.c
 
 EXFAT FILE SYSTEM
 M:	Namjae Jeon <linkinjeon@kernel.org>
@@ -7115,6 +7184,7 @@
 EXYNOS SYSMMU (IOMMU) driver
 M:	Marek Szyprowski <m.szyprowski@samsung.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Maintained
 F:	drivers/iommu/exynos-iommu.c
 
@@ -7239,9 +7309,6 @@
 F:	include/linux/fs_types.h
 F:	include/uapi/linux/fs.h
 F:	include/uapi/linux/openat2.h
-X:	fs/io-wq.c
-X:	fs/io-wq.h
-X:	fs/io_uring.c
 
 FINTEK F75375S HARDWARE MONITOR AND FAN CONTROLLER DRIVER
 M:	Riku Voipio <riku.voipio@iki.fi>
@@ -7250,6 +7317,12 @@
 F:	drivers/hwmon/f75375s.c
 F:	include/linux/f75375s.h
 
+FINTEK F81604 USB to 2xCANBUS DEVICE DRIVER
+M:	Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
+L:	linux-can@vger.kernel.org
+S:	Maintained
+F:	drivers/net/can/usb/f81604.c
+
 FIREWIRE AUDIO DRIVERS and IEC 61883-1/6 PACKET STREAMING ENGINE
 M:	Clemens Ladisch <clemens@ladisch.de>
 M:	Takashi Sakamoto <o-takashi@sakamocchi.jp>
@@ -7744,7 +7817,7 @@
 F:	include/asm-generic/futex.h
 F:	include/linux/futex.h
 F:	include/uapi/linux/futex.h
-F:	kernel/futex.c
+F:	kernel/futex/*
 F:	tools/perf/bench/futex*
 F:	tools/testing/selftests/futex/
 
@@ -7947,9 +8020,10 @@
 
 GOODIX TOUCHSCREEN
 M:	Bastien Nocera <hadess@hadess.net>
+M:	Hans de Goede <hdegoede@redhat.com>
 L:	linux-input@vger.kernel.org
 S:	Maintained
-F:	drivers/input/touchscreen/goodix.c
+F:	drivers/input/touchscreen/goodix*
 
 GOOGLE ETHERNET DRIVERS
 M:	Jeroen de Borst <jeroendb@google.com>
@@ -8565,7 +8639,7 @@
 HP COMPAQ TC1100 TABLET WMI EXTRAS DRIVER
 L:	platform-driver-x86@vger.kernel.org
 S:	Orphan
-F:	drivers/platform/x86/tc1100-wmi.c
+F:	drivers/platform/x86/hp/tc1100-wmi.c
 
 HPET:	High Precision Event Timers driver
 M:	Clemens Ladisch <clemens@ladisch.de>
@@ -9174,6 +9248,14 @@
 F:	drivers/hwmon/ina2xx.c
 F:	include/linux/platform_data/ina2xx.h
 
+INA260 POWER MONITOR DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+R:	Raviteja Narayanam <raviteja.narayanam@xilinx.com>
+R:	Michal Simek <michal.simek@xilinx.com>
+S:	Maintained
+F:	drivers/iio/adc/ina260-adc.c
+F:	Documentation/devicetree/bindings/iio/adc/ti,ina260.yaml
+
 INDUSTRY PACK SUBSYSTEM (IPACK)
 M:	Samuel Iglesias Gonsalvez <siglesias@igalia.com>
 M:	Jens Taprogge <jens.taprogge@taprogge.org>
@@ -9203,6 +9285,7 @@
 F:	include/rdma/
 F:	include/trace/events/ib_mad.h
 F:	include/trace/events/ib_umad.h
+F:	include/trace/misc/rdma.h
 F:	include/uapi/linux/if_infiniband.h
 F:	include/uapi/rdma/
 F:	samples/bpf/ibumad_kern.c
@@ -9457,6 +9540,7 @@
 M:	David Woodhouse <dwmw2@infradead.org>
 M:	Lu Baolu <baolu.lu@linux.intel.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Supported
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu.git
 F:	drivers/iommu/intel/
@@ -9793,6 +9877,7 @@
 M:	Joerg Roedel <joro@8bytes.org>
 M:	Will Deacon <will@kernel.org>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu.git
 F:	Documentation/devicetree/bindings/iommu/
@@ -9810,9 +9895,7 @@
 S:	Maintained
 T:	git git://git.kernel.dk/linux-block
 T:	git git://git.kernel.dk/liburing
-F:	fs/io-wq.c
-F:	fs/io-wq.h
-F:	fs/io_uring.c
+F:	io_uring/
 F:	include/linux/io_uring.h
 F:	include/uapi/linux/io_uring.h
 F:	tools/io_uring/
@@ -10184,6 +10267,12 @@
 F:	fs/nfsd/
 F:	include/linux/lockd/
 F:	include/linux/sunrpc/
+F:	include/trace/events/rpcgss.h
+F:	include/trace/events/rpcrdma.h
+F:	include/trace/events/sunrpc.h
+F:	include/trace/misc/fs.h
+F:	include/trace/misc/nfs.h
+F:	include/trace/misc/sunrpc.h
 F:	include/uapi/linux/nfsd/
 F:	include/uapi/linux/sunrpc/
 F:	net/sunrpc/
@@ -10301,9 +10390,11 @@
 F:	arch/s390/include/asm/gmap.h
 F:	arch/s390/include/asm/kvm*
 F:	arch/s390/include/uapi/asm/kvm*
+F:	arch/s390/include/uapi/asm/uvdevice.h
 F:	arch/s390/kernel/uv.c
 F:	arch/s390/kvm/
 F:	arch/s390/mm/gmap.c
+F:	drivers/s390/char/uvdevice.c
 F:	tools/testing/selftests/kvm/*/s390x/
 F:	tools/testing/selftests/kvm/s390x/
 
@@ -10621,6 +10712,12 @@
 F:	drivers/ata/sata_gemini.c
 F:	drivers/ata/sata_gemini.h
 
+LIBATA SATA AHCI CEVA CONTROLLER DRIVER
+M:	Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
+S:	Maintained
+F:	drivers/ata/ahci_ceva.c
+F:	Documentation/devicetree/bindings/ata/ahci-ceva.txt
+
 LIBATA SATA AHCI PLATFORM devices support
 M:	Hans de Goede <hdegoede@redhat.com>
 M:	Jens Axboe <axboe@kernel.dk>
@@ -10835,7 +10932,7 @@
 S:	Maintained
 F:	Documentation/misc-devices/lis3lv02d.rst
 F:	drivers/misc/lis3lv02d/
-F:	drivers/platform/x86/hp_accel.c
+F:	drivers/platform/x86/hp/hp_accel.c
 
 LIST KUNIT TEST
 M:	David Gow <davidgow@google.com>
@@ -11795,6 +11892,7 @@
 MEDIATEK IOMMU DRIVER
 M:	Yong Wu <yong.wu@mediatek.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	Documentation/devicetree/bindings/iommu/mediatek*
@@ -12224,6 +12322,20 @@
 T:	git git://git.monstr.eu/linux-2.6-microblaze.git
 F:	arch/microblaze/
 
+MICROBLAZE TMR MANAGER
+M:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Supported
+F:	Documentation/ABI/testing/sysfs-driver-xilinx-tmr-manager
+F:	Documentation/devicetree/bindings/misc/xlnx,tmr-manager.yaml
+F:	drivers/misc/xilinx_tmr_manager.c
+
+MICROBLAZE TMR INJECT
+M:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Supported
+F:	Documentation/ABI/testing/sysfs-driver-xilinx-tmr-inject
+F:	Documentation/devicetree/bindings/misc/xlnx,tmr-inject.yaml
+F:	drivers/misc/xilinx_tmr_inject.c
+
 MICROCHIP AT91 DMA DRIVERS
 M:	Ludovic Desroches <ludovic.desroches@microchip.com>
 M:	Tudor Ambarus <tudor.ambarus@microchip.com>
@@ -13393,6 +13505,11 @@
 F:	include/linux/nubus.h
 F:	include/uapi/linux/nubus.h
 
+NUVOTON M058SSAN GPIO DRIVER
+M:	Filippo Copetti <filippo.copetti@eurotech.com>
+S:	Maintained
+F:	drivers/gpio/gpio-m058ssan.c
+
 NVIDIA (rivafb and nvidiafb) FRAMEBUFFER DRIVER
 M:	Antonino Daplas <adaplas@gmail.com>
 L:	linux-fbdev@vger.kernel.org
@@ -13400,6 +13517,12 @@
 F:	drivers/video/fbdev/nvidia/
 F:	drivers/video/fbdev/riva/
 
+NVIDIA WMI EC BACKLIGHT DRIVER
+M:	Daniel Dadap <ddadap@nvidia.com>
+L:	platform-driver-x86@vger.kernel.org
+S:	Supported
+F:	drivers/platform/x86/nvidia-wmi-ec-backlight.c
+
 NVM EXPRESS DRIVER
 M:	Keith Busch <kbusch@kernel.org>
 M:	Jens Axboe <axboe@fb.com>
@@ -13482,6 +13605,12 @@
 F:	Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml
 F:	drivers/gpu/drm/imx/dcss/
 
+NXP PCF85263 RTC DRIVER
+M:	Filippo Copetti <filippo.copetti@eurotech.com>
+S:	Maintained
+F:	drivers/rtc/rtc-pcf85263.c
+F:	drivers/rtc/rtc-pcf85263.h
+
 NXP PF8100/PF8121A/PF8200 PMIC REGULATOR DEVICE DRIVER
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
@@ -15554,6 +15683,7 @@
 QUALCOMM IOMMU
 M:	Rob Clark <robdclark@gmail.com>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 L:	linux-arm-msm@vger.kernel.org
 S:	Maintained
 F:	drivers/iommu/arm/arm-smmu/qcom_iommu.c
@@ -15720,6 +15850,8 @@
 
 RANDOM NUMBER DRIVER
 M:	"Theodore Ts'o" <tytso@mit.edu>
+M:	Jason A. Donenfeld <Jason@zx2c4.com>
+T:	git https://git.kernel.org/pub/scm/linux/kernel/git/crng/random.git
 S:	Maintained
 F:	drivers/char/random.c
 
@@ -16021,6 +16153,12 @@
 F:	Documentation/devicetree/bindings/iio/adc/renesas,rzg2l-adc.yaml
 F:	drivers/iio/adc/rzg2l_adc.c
 
+RENESAS VERSACLOCK 7 CLOCK DRIVER
+M:	Alex Helms <alexander.helms.jy@renesas.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/clock/renesas,versaclock7.yaml
+F:	drivers/clk/clk-versaclock7.c
+
 RESET CONTROLLER FRAMEWORK
 M:	Philipp Zabel <p.zabel@pengutronix.de>
 S:	Maintained
@@ -16408,6 +16546,7 @@
 L:	linux-s390@vger.kernel.org
 L:	kvm@vger.kernel.org
 S:	Supported
+F:	arch/s390/kvm/pci*
 F:	drivers/vfio/pci/vfio_pci_zdev.c
 F:	include/uapi/linux/vfio_zdev.h
 
@@ -17980,6 +18119,7 @@
 SWIOTLB SUBSYSTEM
 M:	Christoph Hellwig <hch@infradead.org>
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Supported
 W:	http://git.infradead.org/users/hch/dma-mapping.git
 T:	git git://git.infradead.org/users/hch/dma-mapping.git
@@ -19573,6 +19713,7 @@
 
 USB XHCI DRIVER
 M:	Mathias Nyman <mathias.nyman@intel.com>
+R:	Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	drivers/usb/host/pci-quirks*
@@ -19630,6 +19771,11 @@
 F:	drivers/uio/
 F:	include/linux/uio_driver.h
 
+USERSPACE I/O (UIO) DRIVER FOR XILINX AI ENGINE NPI
+M:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/soc/xilinx/xlnx,ai-engine-npi.txt
+
 UTIL-LINUX PACKAGE
 M:	Karel Zak <kzak@redhat.com>
 L:	util-linux@vger.kernel.org
@@ -20560,12 +20706,14 @@
 M:	Stefano Stabellini <sstabellini@kernel.org>
 L:	xen-devel@lists.xenproject.org (moderated for non-subscribers)
 L:	iommu@lists.linux-foundation.org
+L:	iommu@lists.linux.dev
 S:	Supported
 F:	arch/x86/xen/*swiotlb*
 F:	drivers/xen/*swiotlb*
 
 XFS FILESYSTEM
 C:	irc://irc.oftc.net/xfs
+M:	Leah Rumancik <leah.rumancik@gmail.com>
 M:	Darrick J. Wong <djwong@kernel.org>
 M:	linux-xfs@vger.kernel.org
 L:	linux-xfs@vger.kernel.org
@@ -20580,10 +20728,204 @@
 F:	include/uapi/linux/dqblk_xfs.h
 F:	include/uapi/linux/fsmap.h
 
+XILINX AUDIO FORMATTER (ASoC) DRIVER
+M:	Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
+R:	Vishal Sagar <vishal.sagar@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
+F:	sound/soc/xilinx/xlnx_formatter_pcm.c
+
+XILINX AXI DMAENGINE DRIVER
+M:	Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+R:	Harini Katakam <harini.katakam@xilinx.com>
+S:	Maintained
+F:	drivers/dma/xilinx/xilinx_dma.c
+F:	Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
+
 XILINX AXI ETHERNET DRIVER
 M:	Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
 S:	Maintained
 F:	drivers/net/ethernet/xilinx/xilinx_axienet*
+F:	Documentation/devicetree/bindings/net/xilinx_axienet.txt
+
+XILINX AXI SPI DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+R:	Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
+S:	Maintained
+F:	drivers/spi/spi-xilinx.c
+F:	Documentation/devicetree/bindings/spi/spi-xilinx.txt
+
+XILINX FLEXNOC PERFORMANCE MONITOR DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+R:	Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
+R:	Srinivas Goud <srinivas.goud@xilinx.com>
+S:	Maintained
+F:	drivers/misc/xilinx_flex_pm.c
+F:	Documentation/devicetree/bindings/misc/xlnx,flexnoc-pm.txt
+
+XILINX AXI USB DRIVER
+M:	Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
+S:	Maintained
+F:	drivers/usb/gadget/udc/udc-xilinx.c
+F:	Documentation/devicetree/bindings/usb/udc-xilinx.txt
+
+XILINX AXI PERFORMANCE MONITOR DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+S:	Maintained
+F:	drivers/uio/uio_xilinx_apm.c
+F:	Documentation/devicetree/bindings/uio/xilinx_apm.txt
+
+XILINX CAN DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+R:	Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/net/can/xilinx_can.c
+F:	Documentation/devicetree/bindings/net/can/xilinx_can.txt
+
+XILINX DMA FRAMEBUFFER READ/WRITE DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/dma/xilinx/xilinx_frmbuf.txt
+F:	drivers/dma/xilinx/xilinx_frmbuf.c
+F:	include/linux/dma/xilinx_frmbuf.h
+
+XILINX EMACLITE DRIVER
+M:	Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+R:	Harini Katakam <harini.katakam@xilinx.com>
+S:	Maintained
+F:	drivers/net/ethernet/xilinx/xilinx_emaclite.c
+F:	Documentation/devicetree/bindings/net/xilinx_emaclite.txt
+
+XILINX GMII2RGMII DRIVER
+M:	Harini Katakam <harini.katakam@xilinx.com>
+R:	Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/net/phy/xilinx_gmii2rgmii.c
+W:	https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842246/Xilinx+GMII2RGMII+convertor
+
+XILINX GQSPI ZYNQMP SPI DRIVER
+M:	Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
+R:	Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
+F:	drivers/spi/spi-zynqmp-gqspi.c
+W:	https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841754/Zynqmp+QSPI+Driver
+
+XILINX I2S AUDIO (ASoC) DRIVER
+M:	Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
+R:	Vishal Sagar <vishal.sagar@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/sound/xlnx,i2s.txt
+F:	sound/soc/xilinx/xlnx_i2s.c
+
+XILINX MEDIA AXIS SWITCH DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,v-axi4s-switch.txt
+F:	drivers/media/platform/xilinx/xilinx-axis-switch.c
+
+XILINX MEDIA AXIS SWITCH DRIVER
+M:	Anil kumar M <anil.mamidala@xilinx.com>
+M:	Karthikeyan T <karthikeyan.thangavel@xilinx.com>
+L:	git@xilinx.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,axis-subsetconv.yaml
+F:	drivers/media/platform/xilinx/xilinx-axis-subsetconv.c
+
+XILINX MEDIA CSI2RXSS DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+L:	git@xilinx.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
+F:	drivers/media/platform/xilinx/xilinx-csi2rxss.c
+F:	include/uapi/linux/xilinx-csi2rxss.h
+
+XILINX MEDIA DEMOSAIC DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+L:	git@xilinx.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,v-demosaic.txt
+F:	drivers/media/platform/xilinx/xilinx-demosaic.c
+
+XILINX MEDIA GAMMA DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,v-gamma-lut.txt
+F:	drivers/media/platform/xilinx/xilinx-gamma.c
+F:	drivers/media/platform/xilinx/xilinx-gamma-coeff.h
+
+XILINX MEDIA SDI RX DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt
+F:	drivers/media/platform/xilinx/xilinx-sdirxss.c
+F:	include/uapi/linux/xilinx-sdirxss.h
+
+XILINX MEDIA VPSS COLOR SPACE CONVERTER DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+L:	git@xilinx.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,v-vpss-csc.txt
+F:	drivers/media/platform/xilinx/xilinx-vpss-csc.c
+
+XILINX MEDIA VPSS SCALER DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+R:	Hyun Kwon <hyun.kwon@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/media/xilinx/xlnx,v-vpss-scaler.txt
+F:	drivers/media/platform/xilinx/xilinx-vpss-scaler.c
+
+XILINX PL SOUND CARD (ASoC) DRIVER
+M:	Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
+R:	Vishal Sagar <vishal.sagar@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	sound/soc/xilinx/xlnx_pl_snd_card.c
+
+XILINX QSPI ZYNQ SPI DRIVER
+M:	Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
+R:	Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
+F:	drivers/spi/spi-zynq-qspi.c
+W:	https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842262/Zynq+QSPI+Driver
+
+XILINX RTC ZYNQMP DRIVER
+M:	Neeli Srinivas <srinivas.neeli@xilinx.com>
+R:	Srinivas Goud <srinivas.goud@xilinx.com>
+R:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+S:	Maintained
+F:	drivers/rtc/rtc-zynqmp.c
+
+XILINX SDI AUDIO (ASoC) DRIVER
+M:	Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
+R:	Vishal Sagar <vishal.sagar@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/sound/xlnx,v-uhdsdi-audio.txt
+F:	sound/soc/xilinx/xlnx_sdi_audio.c
+
+XILINX SPDIF AUDIO (ASoC) DRIVER
+M:	Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
+R:	Vishal Sagar <vishal.sagar@xilinx.com>
+S:	Maintained
+L:	git@xilinx.com
+F:	Documentation/devicetree/bindings/sound/xlnx,spdif.txt
+F:	sound/soc/xilinx/xlnx_spdif.c
 
 XILINX CAN DRIVER
 M:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
@@ -20614,12 +20956,35 @@
 F:	drivers/misc/xilinx_sdfec.c
 F:	include/uapi/misc/xilinx_sdfec.h
 
+XILINX VERSAL SYSMON DRIVER
+M:	Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
+R:	Dragan Cvetic <dragan.cvetic@xilinx.com>
+L:	git@xilinx.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/iio/adc/xlnx,versal-sysmon.yaml
+F:	drivers/iio/adc/versal-sysmon.c
+F:	drivers/iio/adc/versal-sysmon.h
+F:	include/linux/iio/adc/versal-sysmon-events.h
+
+XILINX VERSAL SECURE CONFIGURATION DRIVER
+M:	Harsha <harsha.harsha@xilinx.com>
+R:	Michal Simek <michal.simek@xilinx.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/nvmem/xlnx,versal-sec-cfg.yaml
+F:	drivers/nvmem/xlnx_secure_config.c
+
 XILINX UARTLITE SERIAL DRIVER
 M:	Peter Korsgaard <jacmet@sunsite.dk>
 L:	linux-serial@vger.kernel.org
 S:	Maintained
 F:	drivers/tty/serial/uartlite.c
 
+XILINX UARTPS DRIVER
+M:	Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+S:	Maintained
+F:	drivers/tty/serial/xilinx_uartps.c
+F:	Documentation/devicetree/bindings/serial/cdns,uart.txt
+
 XILINX VIDEO IP CORES
 M:	Hyun Kwon <hyun.kwon@xilinx.com>
 M:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
@@ -20648,6 +21013,101 @@
 F:	Documentation/devicetree/bindings/phy/xlnx,zynqmp-psgtr.yaml
 F:	drivers/phy/xilinx/phy-zynqmp.c
 
+XILINX ZYNQ FPGA MANAGER DRIVER
+M:	Nava Kishore Manne <nava.manne@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/fpga/zynq-fpga.c
+F:	Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt
+
+XILINX ZYNQMP AES DRIVER
+M:	Kalyani Akula <kalyani.akula@xilinx.com>
+M:	Nava Kishore Manne <nava.manne@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/crypto/zynqmp-aes.c
+F:	Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.txt
+
+XILINX ZYNQMP DMAENGINE DRIVER
+M:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+R:	Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
+R:	Harini Katakam <harini.katakam@xilinx.com>
+S:	Maintained
+F:	drivers/dma/xilinx/zynqmp_dma.c
+F:	Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt
+
+XILINX ZYNQMP FPGA MANAGER DRIVER
+M:	Nava Kishore Manne <nava.manne@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/fpga/zynqmp-fpga.c
+F:	Documentation/devicetree/bindings/fpga/xilinx-zynqmp-fpga-mgr.txt
+
+ZYNQMP IPI MAILBOX CONTROLLER DRIVER
+M:	Wendy Liang <wendy.liang@xilinx.com>
+S:	Maintained
+F:	drivers/mailbox/zynqmp-ipi-mailbox.c
+F:	include/linux/mailbox/zynqmp-ipi-message.h
+F:	Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.txt
+
+XILINX VERSAL DDRMC EDAC DRIVER
+M:	Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
+R:	Michal Simek <michal.simek@xilinx.com>
+R:	Srinivas Goud <srinivas.goud@xilinx.com>
+S:	Maintained
+F:	drivers/edac/xilinx_ddrmc_edac.c
+F:	Documentation/devicetree/bindings/edac/xlnx,versal-ddrmc-edac.yaml
+
+XILINX ZYNQMP PHY DRIVER
+M:	Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
+S:	Maintained
+F:	drivers/phy/phy-zynqmp.c
+F:	Documentation/devicetree/bindings/phy/phy-zynqmp.txt
+
+XILINX ZYNQMP R5 REMOTE PROCESSOR (REMOTEPROC) SUBSYSTEM
+M:	Wendy Liang <wendy.liang@xilinx.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.txt
+F:	drivers/remoteproc/zynqmp_r5_remoteproc.c
+
+XILINX ZYNQMP RSA DRIVER
+M:	Nava Kishore Manne <nava.manne@xilinx.com>
+M:	Kalyani Akula <kalyani.akula@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/crypto/zynqmp-rsa.c
+F:	Documentation/devicetree/bindings/crypto/zynqmp-rsa.txt
+
+XILINX ZYNQMP SHA DRIVER
+M:	Nava Kishore Manne <nava.manne@xilinx.com>
+M:	Kalyani Akula <kalyani.akula@xilinx.com>
+R:	Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
+S:	Maintained
+F:	drivers/crypto/zynqmp-sha.c
+F:	Documentation/devicetree/bindings/crypto/zynqmp-sha.txt
+
+XILINX SD-FEC IP CORES
+M:	Derek Kiernan <derek.kiernan@xilinx.com>
+M:	Dragan Cvetic <dragan.cvetic@xilinx.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt
+F:	Documentation/misc-devices/xilinx_sdfec.rst
+F:	drivers/misc/xilinx_sdfec.c
+F:	drivers/misc/Kconfig
+F:	drivers/misc/Makefile
+F:	include/uapi/misc/xilinx_sdfec.h
+
+XILINX EVENT MANAGEMENT DRIVER
+M:	Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
+S:	Maintained
+F:	drivers/soc/xilinx/xlnx_event_manager.c
+F:	include/linux/firmware/xlnx-event-manager.h
+
+XILINX ZYNQMP POWER DRIVER
+M:	Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml
+
 XILLYBUS DRIVER
 M:	Eli Billauer <eli.billauer@gmail.com>
 L:	linux-kernel@vger.kernel.org
--- linux-xilinx-zynqmp-5.15.0.orig/Makefile
+++ linux-xilinx-zynqmp-5.15.0/Makefile
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 15
-SUBLEVEL = 0
+SUBLEVEL = 180
 EXTRAVERSION =
 NAME = Trick or Treat
 
@@ -93,10 +93,17 @@
 
 # If the user is running make -s (silent mode), suppress echoing of
 # commands
+# make-4.0 (and later) keep single letter options in the 1st word of MAKEFLAGS.
 
-ifneq ($(findstring s,$(filter-out --%,$(MAKEFLAGS))),)
-  quiet=silent_
-  KBUILD_VERBOSE = 0
+ifeq ($(filter 3.%,$(MAKE_VERSION)),)
+silence:=$(findstring s,$(firstword -$(MAKEFLAGS)))
+else
+silence:=$(findstring s,$(filter-out --%,$(MAKEFLAGS)))
+endif
+
+ifeq ($(silence),s)
+quiet=silent_
+KBUILD_VERBOSE = 0
 endif
 
 export quiet Q KBUILD_VERBOSE
@@ -430,6 +437,7 @@
 HOSTCC	= gcc
 HOSTCXX	= g++
 endif
+HOSTPKG_CONFIG	= pkg-config
 
 export KBUILD_USERCFLAGS := -Wall -Wmissing-prototypes -Wstrict-prototypes \
 			      -O2 -fomit-frame-pointer -std=gnu89
@@ -480,6 +488,8 @@
 XZ		= xz
 ZSTD		= zstd
 
+PAHOLE_FLAGS	= $(shell PAHOLE=$(PAHOLE) $(srctree)/scripts/pahole-flags.sh)
+
 CHECKFLAGS     := -D__linux__ -Dlinux -D__STDC__ -Dunix -D__unix__ \
 		  -Wbitwise -Wno-return-void -Wno-unknown-attribute $(CF)
 NOSTDINC_FLAGS :=
@@ -508,6 +518,9 @@
 		-I$(objtree)/include \
 		$(USERINCLUDE)
 
+# UBUNTU: Include our third party driver stuff too
+LINUXINCLUDE   += -I$(srctree)/ubuntu/include
+
 KBUILD_AFLAGS   := -D__ASSEMBLY__ -fno-PIE
 KBUILD_CFLAGS   := -Wall -Wundef -Werror=strict-prototypes -Wno-trigraphs \
 		   -fno-strict-aliasing -fno-common -fshort-wchar -fno-PIE \
@@ -523,7 +536,7 @@
 KBUILD_LDFLAGS :=
 CLANG_FLAGS :=
 
-export ARCH SRCARCH CONFIG_SHELL BASH HOSTCC KBUILD_HOSTCFLAGS CROSS_COMPILE LD CC
+export ARCH SRCARCH CONFIG_SHELL BASH HOSTCC KBUILD_HOSTCFLAGS CROSS_COMPILE LD CC HOSTPKG_CONFIG
 export CPP AR NM STRIP OBJCOPY OBJDUMP READELF PAHOLE RESOLVE_BTFIDS LEX YACC AWK INSTALLKERNEL
 export PERL PYTHON3 CHECK CHECKFLAGS MAKE UTS_MACHINE HOSTCXX
 export KGZIP KBZIP2 KLZOP LZMA LZ4 XZ ZSTD
@@ -534,6 +547,7 @@
 export KBUILD_AFLAGS AFLAGS_KERNEL AFLAGS_MODULE
 export KBUILD_AFLAGS_MODULE KBUILD_CFLAGS_MODULE KBUILD_LDFLAGS_MODULE
 export KBUILD_AFLAGS_KERNEL KBUILD_CFLAGS_KERNEL
+export PAHOLE_FLAGS
 
 # Files to ignore in find ... statements
 
@@ -661,7 +675,7 @@
 ifeq ($(KBUILD_EXTMOD),)
 # Objects we will link into vmlinux / subdirs we need to visit
 core-y		:= init/ usr/ arch/$(SRCARCH)/
-drivers-y	:= drivers/ sound/
+drivers-y	:= drivers/ sound/ ubuntu/
 drivers-$(CONFIG_SAMPLES) += samples/
 drivers-$(CONFIG_NET) += net/
 drivers-y	+= virt/
@@ -687,12 +701,19 @@
 
 ifdef CONFIG_CC_IS_GCC
 RETPOLINE_CFLAGS	:= $(call cc-option,-mindirect-branch=thunk-extern -mindirect-branch-register)
+RETPOLINE_CFLAGS	+= $(call cc-option,-mindirect-branch-cs-prefix)
 RETPOLINE_VDSO_CFLAGS	:= $(call cc-option,-mindirect-branch=thunk-inline -mindirect-branch-register)
 endif
 ifdef CONFIG_CC_IS_CLANG
 RETPOLINE_CFLAGS	:= -mretpoline-external-thunk
 RETPOLINE_VDSO_CFLAGS	:= -mretpoline
 endif
+
+ifdef CONFIG_RETHUNK
+RETHUNK_CFLAGS         := -mfunction-return=thunk-extern
+RETPOLINE_CFLAGS       += $(RETHUNK_CFLAGS)
+endif
+ 
 export RETPOLINE_CFLAGS
 export RETPOLINE_VDSO_CFLAGS
 
@@ -811,6 +832,9 @@
 KBUILD_CFLAGS += $(call cc-disable-warning, unused-but-set-variable)
 KBUILD_CFLAGS += $(call cc-disable-warning, unused-const-variable)
 
+# These result in bogus false positives
+KBUILD_CFLAGS += $(call cc-disable-warning, dangling-pointer)
+
 ifdef CONFIG_FRAME_POINTER
 KBUILD_CFLAGS	+= -fno-omit-frame-pointer -fno-optimize-sibling-calls
 else
@@ -831,12 +855,12 @@
 
 # Initialize all stack variables with a zero value.
 ifdef CONFIG_INIT_STACK_ALL_ZERO
-# Future support for zero initialization is still being debated, see
-# https://bugs.llvm.org/show_bug.cgi?id=45497. These flags are subject to being
-# renamed or dropped.
 KBUILD_CFLAGS	+= -ftrivial-auto-var-init=zero
+ifdef CONFIG_CC_HAS_AUTO_VAR_INIT_ZERO_ENABLER
+# https://github.com/llvm/llvm-project/issues/44842
 KBUILD_CFLAGS	+= -enable-trivial-auto-var-init-zero-knowing-it-will-be-removed-from-clang
 endif
+endif
 
 # While VLAs have been removed, GCC produces unreachable stack probes
 # for the randomize_kstack_offset feature. Disable it for all compilers.
@@ -857,7 +881,9 @@
 DEBUG_CFLAGS	+= -g
 endif
 
-ifndef CONFIG_AS_IS_LLVM
+ifdef CONFIG_AS_IS_LLVM
+KBUILD_AFLAGS	+= -g
+else
 KBUILD_AFLAGS	+= -Wa,-gdwarf-2
 endif
 
@@ -865,6 +891,7 @@
 dwarf-version-$(CONFIG_DEBUG_INFO_DWARF4) := 4
 dwarf-version-$(CONFIG_DEBUG_INFO_DWARF5) := 5
 DEBUG_CFLAGS	+= -gdwarf-$(dwarf-version-y)
+KBUILD_AFLAGS	+= -gdwarf-$(dwarf-version-y)
 endif
 
 ifdef CONFIG_DEBUG_INFO_REDUCED
@@ -935,7 +962,6 @@
 ifdef CONFIG_LTO_CLANG
 ifdef CONFIG_LTO_CLANG_THIN
 CC_FLAGS_LTO	:= -flto=thin -fsplit-lto-unit
-KBUILD_LDFLAGS	+= --thinlto-cache-dir=$(extmod_prefix).thinlto-cache
 else
 CC_FLAGS_LTO	:= -flto
 endif
@@ -976,8 +1002,8 @@
 export CC_FLAGS_CFI
 endif
 
-ifdef CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B
-KBUILD_CFLAGS += -falign-functions=64
+ifneq ($(CONFIG_FUNCTION_ALIGNMENT),0)
+KBUILD_CFLAGS += -falign-functions=$(CONFIG_FUNCTION_ALIGNMENT)
 endif
 
 # arch Makefile may override CC so keep this after arch Makefile is included
@@ -1008,6 +1034,21 @@
 KBUILD_CFLAGS += -Wno-maybe-uninitialized
 endif
 
+ifdef CONFIG_CC_IS_GCC
+# The allocators already balk at large sizes, so silence the compiler
+# warnings for bounds checks involving those possible values. While
+# -Wno-alloc-size-larger-than would normally be used here, earlier versions
+# of gcc (<9.1) weirdly don't handle the option correctly when _other_
+# warnings are produced (?!). Using -Walloc-size-larger-than=SIZE_MAX
+# doesn't work (as it is documented to), silently resolving to "0" prior to
+# version 9.1 (and producing an error more recently). Numeric values larger
+# than PTRDIFF_MAX also don't work prior to version 9.1, which are silently
+# ignored, continuing to default to PTRDIFF_MAX. So, left with no other
+# choice, we must perform a versioned check to disable this warning.
+# https://lore.kernel.org/lkml/20210824115859.187f272f@canb.auug.org.au
+KBUILD_CFLAGS += $(call cc-ifversion, -ge, 0901, -Wno-alloc-size-larger-than)
+endif
+
 # disable invalid "can't wrap" optimizations for signed / pointers
 KBUILD_CFLAGS	+= -fno-strict-overflow
 
@@ -1053,6 +1094,11 @@
 KBUILD_LDFLAGS_MODULE += --build-id=sha1
 LDFLAGS_vmlinux += --build-id=sha1
 
+KBUILD_LDFLAGS	+= -z noexecstack
+ifeq ($(CONFIG_LD_IS_BFD),y)
+KBUILD_LDFLAGS	+= $(call ld-option,--no-warn-rwx-segments)
+endif
+
 ifeq ($(CONFIG_STRIP_ASM_SYMS),y)
 LDFLAGS_vmlinux	+= $(call ld-option, -X,)
 endif
@@ -1071,6 +1117,11 @@
 KBUILD_USERCFLAGS  += $(filter -m32 -m64 --target=%, $(KBUILD_CFLAGS))
 KBUILD_USERLDFLAGS += $(filter -m32 -m64 --target=%, $(KBUILD_CFLAGS))
 
+# userspace programs are linked via the compiler, use the correct linker
+ifeq ($(CONFIG_CC_IS_CLANG)$(CONFIG_LD_IS_LLD),yy)
+KBUILD_USERLDFLAGS += $(call cc-option, --ld-path=$(LD))
+endif
+
 # make the checker run with the right architecture
 CHECKFLAGS += --arch=$(ARCH)
 
@@ -1115,7 +1166,9 @@
 export MODULES_NSDEPS := $(extmod_prefix)modules.nsdeps
 
 ifeq ($(KBUILD_EXTMOD),)
-core-y		+= kernel/ certs/ mm/ fs/ ipc/ security/ crypto/ block/
+core-y			+= kernel/ certs/ mm/ fs/ ipc/ security/ crypto/
+core-$(CONFIG_BLOCK)	+= block/
+core-$(CONFIG_IO_URING)	+= io_uring/
 
 vmlinux-dirs	:= $(patsubst %/,%,$(filter %/, \
 		     $(core-y) $(core-m) $(drivers-y) $(drivers-m) \
@@ -1125,13 +1178,11 @@
 		     $(patsubst %/,%,$(filter %/, $(core-) \
 			$(drivers-) $(libs-))))
 
-subdir-modorder := $(addsuffix modules.order,$(filter %/, \
-			$(core-y) $(core-m) $(libs-y) $(libs-m) \
-			$(drivers-y) $(drivers-m)))
-
 build-dirs	:= $(vmlinux-dirs)
 clean-dirs	:= $(vmlinux-alldirs)
 
+subdir-modorder := $(addsuffix /modules.order, $(build-dirs))
+
 # Externally visible symbols (used by link-vmlinux.sh)
 KBUILD_VMLINUX_OBJS := $(head-y) $(patsubst %/,%/built-in.a, $(core-y))
 KBUILD_VMLINUX_OBJS += $(addsuffix built-in.a, $(filter %/, $(libs-y)))
@@ -1160,7 +1211,7 @@
 
 autoksyms_recursive: descend modules.order
 	$(Q)$(CONFIG_SHELL) $(srctree)/scripts/adjust_autoksyms.sh \
-	  "$(MAKE) -f $(srctree)/Makefile vmlinux"
+	  "$(MAKE) -f $(srctree)/Makefile autoksyms_recursive"
 endif
 
 autoksyms_h := $(if $(CONFIG_TRIM_UNUSED_KSYMS), include/generated/autoksyms.h)
@@ -1301,10 +1352,10 @@
 
 PHONY += headers
 headers: $(version_h) scripts_unifdef uapi-asm-generic archheaders archscripts
-	$(if $(wildcard $(srctree)/arch/$(SRCARCH)/include/uapi/asm/Kbuild),, \
-	  $(error Headers not exportable for the $(SRCARCH) architecture))
+	$(if $(filter um, $(SRCARCH)), $(error Headers not exportable for UML))
 	$(Q)$(MAKE) $(hdr-inst)=include/uapi
 	$(Q)$(MAKE) $(hdr-inst)=arch/$(SRCARCH)/include/uapi
+	$(Q)$(MAKE) $(hdr-inst)=ubuntu/include dst=include oldheaders=
 
 # Deprecated. It is no-op now.
 PHONY += headers_check
@@ -1517,7 +1568,7 @@
 # Directories & files removed with 'make clean'
 CLEAN_FILES += include/ksym vmlinux.symvers modules-only.symvers \
 	       modules.builtin modules.builtin.modinfo modules.nsdeps \
-	       compile_commands.json .thinlto-cache
+	       compile_commands.json
 
 # Directories & files removed with 'make mrproper'
 MRPROPER_FILES += include/config include/generated          \
@@ -1745,7 +1796,7 @@
 
 clean-dirs := $(KBUILD_EXTMOD)
 clean: rm-files := $(KBUILD_EXTMOD)/Module.symvers $(KBUILD_EXTMOD)/modules.nsdeps \
-	$(KBUILD_EXTMOD)/compile_commands.json $(KBUILD_EXTMOD)/.thinlto-cache
+	$(KBUILD_EXTMOD)/compile_commands.json
 
 PHONY += prepare
 # now expand this into a simple variable to reduce the cost of shell evaluations
@@ -1792,7 +1843,9 @@
 
 modules_install:
 	$(Q)$(MAKE) -f $(srctree)/scripts/Makefile.modinst
+ifndef modules_sign_only
 	$(call cmd,depmod)
+endif
 
 else # CONFIG_MODULES
 
@@ -1807,6 +1860,8 @@
 	@echo >&2 '***'
 	@exit 1
 
+KBUILD_MODULES :=
+
 endif # CONFIG_MODULES
 
 # Single targets
@@ -1832,18 +1887,12 @@
 $(single-no-ko): descend
 	@:
 
-ifeq ($(KBUILD_EXTMOD),)
-# For the single build of in-tree modules, use a temporary file to avoid
-# the situation of modules_install installing an invalid modules.order.
-MODORDER := .modules.tmp
-endif
-
+# Remove MODORDER when done because it is not the real one.
 PHONY += single_modpost
 single_modpost: $(single-no-ko) modules_prepare
 	$(Q){ $(foreach m, $(single-ko), echo $(extmod_prefix)$m;) } > $(MODORDER)
 	$(Q)$(MAKE) -f $(srctree)/scripts/Makefile.modpost
-
-KBUILD_MODULES := 1
+	$(Q)rm -f $(MODORDER)
 
 export KBUILD_SINGLE_TARGETS := $(addprefix $(extmod_prefix), $(single-no-ko))
 
@@ -1851,10 +1900,8 @@
 build-dirs := $(foreach d, $(build-dirs), \
 			$(if $(filter $(d)/%, $(KBUILD_SINGLE_TARGETS)), $(d)))
 
-endif
+KBUILD_MODULES := 1
 
-ifndef CONFIG_MODULES
-KBUILD_MODULES :=
 endif
 
 # Handle descending into subdirectories listed in $(build-dirs)
--- linux-xilinx-zynqmp-5.15.0.orig/Ubuntu.md
+++ linux-xilinx-zynqmp-5.15.0/Ubuntu.md
@@ -0,0 +1,8 @@
+Name:    linux-xilinx-zynqmp
+Version: 5.15.0
+Series:  22.04 (jammy)
+Description:
+    This is the source code for the Ubuntu linux kernel for the 22.04 series. This
+    source tree is used to produce the flavours: xilinx-zynqmp.
+    This kernel is configured to support the widest range of desktop, laptop and
+    server configurations.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/Kconfig
@@ -9,6 +9,14 @@
 #
 source "arch/$(SRCARCH)/Kconfig"
 
+config ARCH_CONFIGURES_CPU_MITIGATIONS
+	bool
+
+if !ARCH_CONFIGURES_CPU_MITIGATIONS
+config CPU_MITIGATIONS
+	def_bool y
+endif
+
 menu "General architecture-dependent options"
 
 config CRASH_CORE
@@ -200,6 +208,9 @@
 config TRACE_IRQFLAGS_SUPPORT
 	bool
 
+config TRACE_IRQFLAGS_NMI_SUPPORT
+	bool
+
 #
 # An arch should select this if it provides all these things:
 #
@@ -261,6 +272,9 @@
 config ARCH_HAS_DMA_CLEAR_UNCACHED
 	bool
 
+config ARCH_HAS_CPU_FINALIZE_INIT
+	bool
+
 # Select if arch init_task must go in the __init_task_data section
 config ARCH_TASK_STRUCT_ON_STACK
 	bool
@@ -599,6 +613,7 @@
 	bool "Clang Shadow Call Stack"
 	depends on CC_IS_CLANG && ARCH_SUPPORTS_SHADOW_CALL_STACK
 	depends on DYNAMIC_FTRACE_WITH_REGS || !FUNCTION_GRAPH_TRACER
+	depends on MMU
 	help
 	  This option enables Clang's Shadow Call Stack, which uses a
 	  shadow stack to protect function return addresses from being
@@ -1141,6 +1156,7 @@
 config RANDOMIZE_KSTACK_OFFSET_DEFAULT
 	bool "Randomize kernel stack offset on syscall entry"
 	depends on HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET
+	depends on INIT_STACK_NONE || !CC_IS_CLANG || CLANG_VERSION >= 140000
 	help
 	  The kernel stack offset can be randomized (after pt_regs) by
 	  roughly 5 bits of entropy, frustrating memory corruption
@@ -1234,6 +1250,9 @@
 config ARCH_HAS_MEM_ENCRYPT
 	bool
 
+config ARCH_HAS_CC_PLATFORM
+	bool
+
 config HAVE_SPARSE_SYSCALL_NR
        bool
        help
@@ -1288,8 +1307,35 @@
 config ARCH_HAS_PARANOID_L1D_FLUSH
 	bool
 
+config DYNAMIC_SIGFRAME
+	bool
+
 source "kernel/gcov/Kconfig"
 
 source "scripts/gcc-plugins/Kconfig"
 
+config FUNCTION_ALIGNMENT_4B
+	bool
+
+config FUNCTION_ALIGNMENT_8B
+	bool
+
+config FUNCTION_ALIGNMENT_16B
+	bool
+
+config FUNCTION_ALIGNMENT_32B
+	bool
+
+config FUNCTION_ALIGNMENT_64B
+	bool
+
+config FUNCTION_ALIGNMENT
+	int
+	default 64 if FUNCTION_ALIGNMENT_64B
+	default 32 if FUNCTION_ALIGNMENT_32B
+	default 16 if FUNCTION_ALIGNMENT_16B
+	default 8 if FUNCTION_ALIGNMENT_8B
+	default 4 if FUNCTION_ALIGNMENT_4B
+	default 0
+
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/boot/tools/objstrip.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/boot/tools/objstrip.c
@@ -148,7 +148,7 @@
 #ifdef __ELF__
     elf = (struct elfhdr *) buf;
 
-    if (elf->e_ident[0] == 0x7f && str_has_prefix((char *)elf->e_ident + 1, "ELF")) {
+    if (memcmp(&elf->e_ident[EI_MAG0], ELFMAG, SELFMAG) == 0) {
 	if (elf->e_type != ET_EXEC) {
 	    fprintf(stderr, "%s: %s is not an ELF executable\n",
 		    prog_name, inname);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/asm/elf.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/asm/elf.h
@@ -74,7 +74,7 @@
 /*
  * This is used to ensure we don't load something for the wrong architecture.
  */
-#define elf_check_arch(x) ((x)->e_machine == EM_ALPHA)
+#define elf_check_arch(x) (((x)->e_machine == EM_ALPHA) && !((x)->e_flags & EF_ALPHA_32BIT))
 
 /*
  * These are used to set parameters in the core dumps.
@@ -145,10 +145,6 @@
 	: amask (AMASK_CIX) ? "ev6" : "ev67");	\
 })
 
-#define SET_PERSONALITY(EX)					\
-	set_personality(((EX).e_flags & EF_ALPHA_32BIT)		\
-	   ? PER_LINUX_32BIT : PER_LINUX)
-
 extern int alpha_l1i_cacheshape;
 extern int alpha_l1d_cacheshape;
 extern int alpha_l2_cacheshape;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/asm/page.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/asm/page.h
@@ -18,7 +18,7 @@
 #define clear_user_page(page, vaddr, pg)	clear_page(page)
 
 #define alloc_zeroed_user_highpage_movable(vma, vaddr) \
-	alloc_page_vma(GFP_HIGHUSER_MOVABLE | __GFP_ZERO, vma, vmaddr)
+	alloc_page_vma(GFP_HIGHUSER_MOVABLE | __GFP_ZERO, vma, vaddr)
 #define __HAVE_ARCH_ALLOC_ZEROED_USER_HIGHPAGE_MOVABLE
 
 extern void copy_page(void * _to, void * _from);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/asm/pgtable.h
@@ -340,7 +340,7 @@
 
 extern void paging_init(void);
 
-/* We have our own get_unmapped_area to cope with ADDR_LIMIT_32BIT.  */
+/* We have our own get_unmapped_area */
 #define HAVE_ARCH_UNMAPPED_AREA
 
 #endif /* _ALPHA_PGTABLE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/asm/processor.h
@@ -8,23 +8,19 @@
 #ifndef __ASM_ALPHA_PROCESSOR_H
 #define __ASM_ALPHA_PROCESSOR_H
 
-#include <linux/personality.h>	/* for ADDR_LIMIT_32BIT */
-
 /*
  * We have a 42-bit user address space: 4TB user VM...
  */
 #define TASK_SIZE (0x40000000000UL)
 
-#define STACK_TOP \
-  (current->personality & ADDR_LIMIT_32BIT ? 0x80000000 : 0x00120000000UL)
+#define STACK_TOP (0x00120000000UL)
 
 #define STACK_TOP_MAX	0x00120000000UL
 
 /* This decides where the kernel will search for a free chunk of vm
  * space during mmap's.
  */
-#define TASK_UNMAPPED_BASE \
-  ((current->personality & ADDR_LIMIT_32BIT) ? 0x40000000 : TASK_SIZE / 2)
+#define TASK_UNMAPPED_BASE (TASK_SIZE / 2)
 
 typedef struct {
 	unsigned long seg;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/asm/thread_info.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/asm/thread_info.h
@@ -77,7 +77,7 @@
 
 /* Work to do on interrupt/exception return.  */
 #define _TIF_WORK_MASK		(_TIF_SIGPENDING | _TIF_NEED_RESCHED | \
-				 _TIF_NOTIFY_RESUME)
+				 _TIF_NOTIFY_RESUME | _TIF_NOTIFY_SIGNAL)
 
 /* Work to do on any return to userspace.  */
 #define _TIF_ALLWORK_MASK	(_TIF_WORK_MASK		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/asm/timex.h
@@ -28,5 +28,6 @@
 	__asm__ __volatile__ ("rpcc %0" : "=r"(ret));
 	return ret;
 }
+#define get_cycles get_cycles
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/include/uapi/asm/ptrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/include/uapi/asm/ptrace.h
@@ -42,6 +42,8 @@
 	unsigned long trap_a0;
 	unsigned long trap_a1;
 	unsigned long trap_a2;
+/* This makes the stack 16-byte aligned as GCC expects */
+	unsigned long __pad0;
 /* These are saved by PAL-code: */
 	unsigned long ps;
 	unsigned long pc;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/asm-offsets.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/asm-offsets.c
@@ -32,7 +32,9 @@
         DEFINE(CRED_EGID, offsetof(struct cred, egid));
         BLANK();
 
+	DEFINE(SP_OFF, offsetof(struct pt_regs, ps));
 	DEFINE(SIZEOF_PT_REGS, sizeof(struct pt_regs));
+	DEFINE(SWITCH_STACK_SIZE, sizeof(struct switch_stack));
 	DEFINE(PT_PTRACED, PT_PTRACED);
 	DEFINE(CLONE_VM, CLONE_VM);
 	DEFINE(CLONE_UNTRACED, CLONE_UNTRACED);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/entry.S
@@ -15,10 +15,6 @@
 	.set noat
 	.cfi_sections	.debug_frame
 
-/* Stack offsets.  */
-#define SP_OFF			184
-#define SWITCH_STACK_SIZE	320
-
 .macro	CFI_START_OSF_FRAME	func
 	.align	4
 	.globl	\func
@@ -199,8 +195,8 @@
 CFI_START_OSF_FRAME entMM
 	SAVE_ALL
 /* save $9 - $15 so the inline exception code can manipulate them.  */
-	subq	$sp, 56, $sp
-	.cfi_adjust_cfa_offset	56
+	subq	$sp, 64, $sp
+	.cfi_adjust_cfa_offset	64
 	stq	$9, 0($sp)
 	stq	$10, 8($sp)
 	stq	$11, 16($sp)
@@ -215,7 +211,7 @@
 	.cfi_rel_offset	$13, 32
 	.cfi_rel_offset	$14, 40
 	.cfi_rel_offset	$15, 48
-	addq	$sp, 56, $19
+	addq	$sp, 64, $19
 /* handle the fault */
 	lda	$8, 0x3fff
 	bic	$sp, $8, $8
@@ -228,7 +224,7 @@
 	ldq	$13, 32($sp)
 	ldq	$14, 40($sp)
 	ldq	$15, 48($sp)
-	addq	$sp, 56, $sp
+	addq	$sp, 64, $sp
 	.cfi_restore	$9
 	.cfi_restore	$10
 	.cfi_restore	$11
@@ -236,7 +232,7 @@
 	.cfi_restore	$13
 	.cfi_restore	$14
 	.cfi_restore	$15
-	.cfi_adjust_cfa_offset	-56
+	.cfi_adjust_cfa_offset	-64
 /* finish up the syscall as normal.  */
 	br	ret_from_sys_call
 CFI_END_OSF_FRAME entMM
@@ -383,8 +379,8 @@
 	.cfi_restore	$0
 	.cfi_adjust_cfa_offset	-256
 	SAVE_ALL		/* setup normal kernel stack */
-	lda	$sp, -56($sp)
-	.cfi_adjust_cfa_offset	56
+	lda	$sp, -64($sp)
+	.cfi_adjust_cfa_offset	64
 	stq	$9, 0($sp)
 	stq	$10, 8($sp)
 	stq	$11, 16($sp)
@@ -400,7 +396,7 @@
 	.cfi_rel_offset	$14, 40
 	.cfi_rel_offset	$15, 48
 	lda	$8, 0x3fff
-	addq	$sp, 56, $19
+	addq	$sp, 64, $19
 	bic	$sp, $8, $8
 	jsr	$26, do_entUnaUser
 	ldq	$9, 0($sp)
@@ -410,7 +406,7 @@
 	ldq	$13, 32($sp)
 	ldq	$14, 40($sp)
 	ldq	$15, 48($sp)
-	lda	$sp, 56($sp)
+	lda	$sp, 64($sp)
 	.cfi_restore	$9
 	.cfi_restore	$10
 	.cfi_restore	$11
@@ -418,7 +414,7 @@
 	.cfi_restore	$13
 	.cfi_restore	$14
 	.cfi_restore	$15
-	.cfi_adjust_cfa_offset	-56
+	.cfi_adjust_cfa_offset	-64
 	br	ret_from_sys_call
 CFI_END_OSF_FRAME entUna
 
@@ -469,8 +465,10 @@
 #ifdef CONFIG_AUDITSYSCALL
 	lda     $6, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT
 	and     $3, $6, $3
-#endif
 	bne     $3, strace
+#else
+	blbs    $3, strace		/* check for SYSCALL_TRACE in disguise */
+#endif
 	beq	$4, 1f
 	ldq	$27, 0($5)
 1:	jsr	$26, ($27), sys_ni_syscall
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/irq.c
@@ -60,7 +60,7 @@
 		cpu = (cpu < (NR_CPUS-1) ? cpu + 1 : 0);
 	last_cpu = cpu;
 
-	cpumask_copy(irq_data_get_affinity_mask(data), cpumask_of(cpu));
+	irq_data_update_affinity(data, cpumask_of(cpu));
 	chip->irq_set_affinity(data, cpumask_of(cpu), false);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/module.c
@@ -146,10 +146,8 @@
 	base = (void *)sechdrs[sechdrs[relsec].sh_info].sh_addr;
 	symtab = (Elf64_Sym *)sechdrs[symindex].sh_addr;
 
-	/* The small sections were sorted to the end of the segment.
-	   The following should definitely cover them.  */
-	gp = (u64)me->core_layout.base + me->core_layout.size - 0x8000;
 	got = sechdrs[me->arch.gotsecindex].sh_addr;
+	gp = got + 0x8000;
 
 	for (i = 0; i < n; i++) {
 		unsigned long r_sym = ELF64_R_SYM (rela[i].r_info);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/osf_sys.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/osf_sys.c
@@ -1212,8 +1212,7 @@
 	return ret;
 }
 
-/* Get an address range which is currently unmapped.  Similar to the
-   generic version except that we know how to honor ADDR_LIMIT_32BIT.  */
+/* Get an address range which is currently unmapped. */
 
 static unsigned long
 arch_get_unmapped_area_1(unsigned long addr, unsigned long len,
@@ -1235,13 +1234,7 @@
 		       unsigned long len, unsigned long pgoff,
 		       unsigned long flags)
 {
-	unsigned long limit;
-
-	/* "32 bit" actually means 31 bit, since pointers sign extend.  */
-	if (current->personality & ADDR_LIMIT_32BIT)
-		limit = 0x80000000;
-	else
-		limit = TASK_SIZE;
+	unsigned long limit = TASK_SIZE;
 
 	if (len > limit)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/rtc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/rtc.c
@@ -80,7 +80,12 @@
 static int
 alpha_rtc_read_time(struct device *dev, struct rtc_time *tm)
 {
-	mc146818_get_time(tm);
+	int ret = mc146818_get_time(tm);
+
+	if (ret < 0) {
+		dev_err_ratelimited(dev, "unable to read current time\n");
+		return ret;
+	}
 
 	/* Adjust for non-default epochs.  It's easier to depend on the
 	   generic __get_rtc_time and adjust the epoch here than create
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/setup.c
@@ -385,8 +385,7 @@
 #endif /* CONFIG_BLK_DEV_INITRD */
 }
 
-int __init
-page_is_ram(unsigned long pfn)
+int page_is_ram(unsigned long pfn)
 {
 	struct memclust_struct * cluster;
 	struct memdesc_struct * memdesc;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/srmcons.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/srmcons.c
@@ -59,7 +59,7 @@
 	} while((result.bits.status & 1) && (++loops < 10));
 
 	if (count)
-		tty_schedule_flip(port);
+		tty_flip_buffer_push(port);
 
 	return count;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/kernel/traps.c
@@ -192,7 +192,7 @@
 		local_irq_enable();
 		while (1);
 	}
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 #ifndef CONFIG_MATHEMU
@@ -235,7 +235,21 @@
 {
 	int signo, code;
 
-	if ((regs->ps & ~IPL_MAX) == 0) {
+	if (type == 3) { /* FEN fault */
+		/* Irritating users can call PAL_clrfen to disable the
+		   FPU for the process.  The kernel will then trap in
+		   do_switch_stack and undo_switch_stack when we try
+		   to save and restore the FP registers.
+
+		   Given that GCC by default generates code that uses the
+		   FP registers, PAL_clrfen is not useful except for DoS
+		   attacks.  So turn the bleeding FPU back on and be done
+		   with it.  */
+		current_thread_info()->pcb.flags |= 1;
+		__reload_thread(&current_thread_info()->pcb);
+		return;
+	}
+	if (!user_mode(regs)) {
 		if (type == 1) {
 			const unsigned int *data
 			  = (const unsigned int *) regs->pc;
@@ -368,20 +382,6 @@
 		}
 		break;
 
-	      case 3: /* FEN fault */
-		/* Irritating users can call PAL_clrfen to disable the
-		   FPU for the process.  The kernel will then trap in
-		   do_switch_stack and undo_switch_stack when we try
-		   to save and restore the FP registers.
-
-		   Given that GCC by default generates code that uses the
-		   FP registers, PAL_clrfen is not useful except for DoS
-		   attacks.  So turn the bleeding FPU back on and be done
-		   with it.  */
-		current_thread_info()->pcb.flags |= 1;
-		__reload_thread(&current_thread_info()->pcb);
-		return;
-
 	      case 5: /* illoc */
 	      default: /* unexpected instruction-fault type */
 		      ;
@@ -577,7 +577,7 @@
 
 	printk("Bad unaligned kernel access at %016lx: %p %lx %lu\n",
 		pc, va, opcode, reg);
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 
 got_exception:
 	/* Ok, we caught the exception, but we don't want it.  Is there
@@ -632,7 +632,7 @@
 		local_irq_enable();
 		while (1);
 	}
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 /*
@@ -709,7 +709,7 @@
 static int unauser_reg_offsets[32] = {
 	R(r0), R(r1), R(r2), R(r3), R(r4), R(r5), R(r6), R(r7), R(r8),
 	/* r9 ... r15 are stored in front of regs.  */
-	-56, -48, -40, -32, -24, -16, -8,
+	-64, -56, -48, -40, -32, -24, -16,	/* padding at -8 */
 	R(r16), R(r17), R(r18),
 	R(r19), R(r20), R(r21), R(r22), R(r23), R(r24), R(r25), R(r26),
 	R(r27), R(r28), R(gp),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/alpha/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/alpha/mm/fault.c
@@ -78,8 +78,8 @@
 
 /* Macro for exception fixup code to access integer registers.  */
 #define dpf_reg(r)							\
-	(((unsigned long *)regs)[(r) <= 8 ? (r) : (r) <= 15 ? (r)-16 :	\
-				 (r) <= 18 ? (r)+10 : (r)-10])
+	(((unsigned long *)regs)[(r) <= 8 ? (r) : (r) <= 15 ? (r)-17 :	\
+				 (r) <= 18 ? (r)+11 : (r)-10])
 
 asmlinkage void
 do_page_fault(unsigned long address, unsigned long mmcsr,
@@ -204,7 +204,7 @@
 	printk(KERN_ALERT "Unable to handle kernel paging request at "
 	       "virtual address %016lx\n", address);
 	die_if_kernel("Oops", regs, cause, (unsigned long*)regs - 16);
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 
 	/* We ran out of memory, or some other thing happened to us that
 	   made us unable to handle the page fault gracefully.  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/Makefile
@@ -6,7 +6,7 @@
 KBUILD_DEFCONFIG := haps_hs_smp_defconfig
 
 ifeq ($(CROSS_COMPILE),)
-CROSS_COMPILE := $(call cc-cross-prefix, arc-linux- arceb-linux-)
+CROSS_COMPILE := $(call cc-cross-prefix, arc-linux- arceb-linux- arc-linux-gnu-)
 endif
 
 cflags-y	+= -fno-common -pipe -fno-builtin -mmedium-calls -D__linux__
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/boot/dts/hsdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/boot/dts/hsdk.dts
@@ -205,7 +205,6 @@
 		};
 
 		gmac: ethernet@8000 {
-			#interrupt-cells = <1>;
 			compatible = "snps,dwmac";
 			reg = <0x8000 0x2000>;
 			interrupts = <10>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/include/asm/atomic-llsc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/include/asm/atomic-llsc.h
@@ -18,7 +18,7 @@
 	: [val]	"=&r"	(val) /* Early clobber to prevent reg reuse */	\
 	: [ctr]	"r"	(&v->counter), /* Not "m": llock only supports reg direct addr mode */	\
 	  [i]	"ir"	(i)						\
-	: "cc");							\
+	: "cc", "memory");						\
 }									\
 
 #define ATOMIC_OP_RETURN(op, c_op, asm_op)				\
@@ -34,7 +34,7 @@
 	: [val]	"=&r"	(val)						\
 	: [ctr]	"r"	(&v->counter),					\
 	  [i]	"ir"	(i)						\
-	: "cc");							\
+	: "cc", "memory");						\
 									\
 	return val;							\
 }
@@ -56,7 +56,7 @@
 	  [orig] "=&r" (orig)						\
 	: [ctr]	"r"	(&v->counter),					\
 	  [i]	"ir"	(i)						\
-	: "cc");							\
+	: "cc", "memory");						\
 									\
 	return orig;							\
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/include/asm/atomic64-arcv2.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/include/asm/atomic64-arcv2.h
@@ -60,7 +60,7 @@
 	"	bnz     1b		\n"				\
 	: "=&r"(val)							\
 	: "r"(&v->counter), "ir"(a)					\
-	: "cc");							\
+	: "cc", "memory");						\
 }									\
 
 #define ATOMIC64_OP_RETURN(op, op1, op2)		        	\
@@ -77,7 +77,7 @@
 	"	bnz     1b		\n"				\
 	: [val] "=&r"(val)						\
 	: "r"(&v->counter), "ir"(a)					\
-	: "cc");	/* memory clobber comes from smp_mb() */	\
+	: "cc", "memory");						\
 									\
 	return val;							\
 }
@@ -99,7 +99,7 @@
 	"	bnz     1b		\n"				\
 	: "=&r"(orig), "=&r"(val)					\
 	: "r"(&v->counter), "ir"(a)					\
-	: "cc");	/* memory clobber comes from smp_mb() */	\
+	: "cc", "memory");						\
 									\
 	return orig;							\
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/include/asm/io.h
@@ -32,7 +32,7 @@
 {
 }
 
-extern void iounmap(const void __iomem *addr);
+extern void iounmap(const volatile void __iomem *addr);
 
 /*
  * io{read,write}{16,32}be() macros
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/include/asm/kprobes.h
@@ -46,7 +46,7 @@
 };
 
 int kprobe_fault_handler(struct pt_regs *regs, unsigned long cause);
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 void trap_is_kprobe(unsigned long address, struct pt_regs *regs);
 #else
 #define trap_is_kprobe(address, regs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/include/asm/linkage.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/include/asm/linkage.h
@@ -8,6 +8,10 @@
 
 #include <asm/dwarf.h>
 
+#define ASM_NL		 `	/* use '`' to mark new line in macro */
+#define __ALIGN		.align 4
+#define __ALIGN_STR	__stringify(__ALIGN)
+
 #ifdef __ASSEMBLY__
 
 .macro ST2 e, o, off
@@ -28,10 +32,6 @@
 #endif
 .endm
 
-#define ASM_NL		 `	/* use '`' to mark new line in macro */
-#define __ALIGN		.align 4
-#define __ALIGN_STR	__stringify(__ALIGN)
-
 /* annotation for data we want in DCCM - if enabled in .config */
 .macro ARCFP_DATA nm
 #ifdef CONFIG_ARC_HAS_DCCM
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/include/asm/pgtable-levels.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/include/asm/pgtable-levels.h
@@ -163,7 +163,7 @@
 #define pmd_page_vaddr(pmd)	(pmd_val(pmd) & PAGE_MASK)
 #define pmd_page(pmd)		virt_to_page(pmd_page_vaddr(pmd))
 #define set_pmd(pmdp, pmd)	(*(pmdp) = pmd)
-#define pmd_pgtable(pmd)	((pgtable_t) pmd_page_vaddr(pmd))
+#define pmd_pgtable(pmd)	((pgtable_t) pmd_page(pmd))
 
 /*
  * 4th level paging: pte
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/kernel/entry.S
@@ -196,6 +196,7 @@
 	st  r0, [sp, PT_r0]     ; sys call return value in pt_regs
 
 	;POST Sys Call Ptrace Hook
+	mov r0, sp		; pt_regs needed
 	bl  @syscall_trace_exit
 	b   ret_from_exception ; NOT ret_from_system_call at is saves r0 which
 	; we'd done before calling post hook above
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/kernel/kprobes.c
@@ -363,8 +363,9 @@
 
 static void __used kretprobe_trampoline_holder(void)
 {
-	__asm__ __volatile__(".global kretprobe_trampoline\n"
-			     "kretprobe_trampoline:\n" "nop\n");
+	__asm__ __volatile__(".global __kretprobe_trampoline\n"
+			     "__kretprobe_trampoline:\n"
+			     "nop\n");
 }
 
 void __kprobes arch_prepare_kretprobe(struct kretprobe_instance *ri,
@@ -375,13 +376,13 @@
 	ri->fp = NULL;
 
 	/* Replace the return addr with trampoline addr */
-	regs->blink = (unsigned long)&kretprobe_trampoline;
+	regs->blink = (unsigned long)&__kretprobe_trampoline;
 }
 
 static int __kprobes trampoline_probe_handler(struct kprobe *p,
 					      struct pt_regs *regs)
 {
-	regs->ret = __kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	regs->ret = __kretprobe_trampoline_handler(regs, NULL);
 
 	/* By returning a non zero value, we are telling the kprobe handler
 	 * that we don't want the post_handler to run
@@ -390,7 +391,7 @@
 }
 
 static struct kprobe trampoline_p = {
-	.addr = (kprobe_opcode_t *) &kretprobe_trampoline,
+	.addr = (kprobe_opcode_t *) &__kretprobe_trampoline,
 	.pre_handler = trampoline_probe_handler
 };
 
@@ -402,7 +403,7 @@
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
 {
-	if (p->addr == (kprobe_opcode_t *) &kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *) &__kretprobe_trampoline)
 		return 1;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/kernel/process.c
@@ -43,7 +43,7 @@
 	return task_thread_info(current)->thr_ptr;
 }
 
-SYSCALL_DEFINE3(arc_usr_cmpxchg, int *, uaddr, int, expected, int, new)
+SYSCALL_DEFINE3(arc_usr_cmpxchg, int __user *, uaddr, int, expected, int, new)
 {
 	struct pt_regs *regs = current_pt_regs();
 	u32 uval;
@@ -294,7 +294,7 @@
 	eflags = x->e_flags;
 	if ((eflags & EF_ARC_OSABI_MSK) != EF_ARC_OSABI_CURRENT) {
 		pr_err("ABI mismatch - you need newer toolchain\n");
-		force_sigsegv(SIGSEGV);
+		force_fatal_sig(SIGSEGV);
 		return 0;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/kernel/signal.c
@@ -61,7 +61,7 @@
 	unsigned int sigret_magic;
 };
 
-static int save_arcv2_regs(struct sigcontext *mctx, struct pt_regs *regs)
+static int save_arcv2_regs(struct sigcontext __user *mctx, struct pt_regs *regs)
 {
 	int err = 0;
 #ifndef CONFIG_ISA_ARCOMPACT
@@ -74,12 +74,12 @@
 #else
 	v2abi.r58 = v2abi.r59 = 0;
 #endif
-	err = __copy_to_user(&mctx->v2abi, &v2abi, sizeof(v2abi));
+	err = __copy_to_user(&mctx->v2abi, (void const *)&v2abi, sizeof(v2abi));
 #endif
 	return err;
 }
 
-static int restore_arcv2_regs(struct sigcontext *mctx, struct pt_regs *regs)
+static int restore_arcv2_regs(struct sigcontext __user *mctx, struct pt_regs *regs)
 {
 	int err = 0;
 #ifndef CONFIG_ISA_ARCOMPACT
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/mm/init.c
@@ -59,13 +59,13 @@
 
 		low_mem_sz = size;
 		in_use = 1;
-		memblock_add_node(base, size, 0);
+		memblock_add_node(base, size, 0, MEMBLOCK_NONE);
 	} else {
 #ifdef CONFIG_HIGHMEM
 		high_mem_start = base;
 		high_mem_sz = size;
 		in_use = 1;
-		memblock_add_node(base, size, 1);
+		memblock_add_node(base, size, 1, MEMBLOCK_NONE);
 		memblock_reserve(base, size);
 #endif
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arc/mm/ioremap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arc/mm/ioremap.c
@@ -94,7 +94,7 @@
 EXPORT_SYMBOL(ioremap_prot);
 
 
-void iounmap(const void __iomem *addr)
+void iounmap(const volatile void __iomem *addr)
 {
 	/* weird double cast to handle phys_addr_t > 32 bits */
 	if (arc_uncached_addr_space((phys_addr_t)(u32)addr))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/Kconfig
@@ -4,6 +4,7 @@
 	default y
 	select ARCH_32BIT_OFF_T
 	select ARCH_HAS_BINFMT_FLAT
+	select ARCH_HAS_CPU_FINALIZE_INIT if MMU
 	select ARCH_HAS_DEBUG_VIRTUAL if MMU
 	select ARCH_HAS_DMA_WRITE_COMBINE if !ARM_DMA_MEM_BUFFERABLE
 	select ARCH_HAS_ELF_RANDOMIZE
@@ -1455,6 +1456,7 @@
 	bool "High Memory Support"
 	depends on MMU
 	select KMAP_LOCAL
+	select KMAP_LOCAL_NON_LINEAR_PTE_ARRAY
 	help
 	  The address space of ARM processors is only 4 Gigabytes large
 	  and it has to accommodate user address space, kernel address
@@ -1740,7 +1742,6 @@
 choice
 	prompt "Kernel command line type" if CMDLINE != ""
 	default CMDLINE_FROM_BOOTLOADER
-	depends on ATAGS
 
 config CMDLINE_FROM_BOOTLOADER
 	bool "Use bootloader kernel arguments if available"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/Kconfig.debug
@@ -410,12 +410,12 @@
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX25.
 
-	config DEBUG_IMX21_IMX27_UART
-		bool "i.MX21 and i.MX27 Debug UART"
-		depends on SOC_IMX21 || SOC_IMX27
+	config DEBUG_IMX27_UART
+		bool "i.MX27 Debug UART"
+		depends on SOC_IMX27
 		help
 		  Say Y here if you want kernel low-level debugging support
-		  on i.MX21 or i.MX27.
+		  on i.MX27.
 
 	config DEBUG_IMX28_UART
 		bool "i.MX28 Debug UART"
@@ -1481,7 +1481,7 @@
 	int "i.MX Debug UART Port Selection"
 	depends on DEBUG_IMX1_UART || \
 		   DEBUG_IMX25_UART || \
-		   DEBUG_IMX21_IMX27_UART || \
+		   DEBUG_IMX27_UART || \
 		   DEBUG_IMX31_UART || \
 		   DEBUG_IMX35_UART || \
 		   DEBUG_IMX50_UART || \
@@ -1540,12 +1540,12 @@
 	default "debug/icedcc.S" if DEBUG_ICEDCC
 	default "debug/imx.S" if DEBUG_IMX1_UART || \
 				 DEBUG_IMX25_UART || \
-				 DEBUG_IMX21_IMX27_UART || \
+				 DEBUG_IMX27_UART || \
 				 DEBUG_IMX31_UART || \
 				 DEBUG_IMX35_UART || \
 				 DEBUG_IMX50_UART || \
 				 DEBUG_IMX51_UART || \
-				 DEBUG_IMX53_UART ||\
+				 DEBUG_IMX53_UART || \
 				 DEBUG_IMX6Q_UART || \
 				 DEBUG_IMX6SL_UART || \
 				 DEBUG_IMX6SX_UART || \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/Makefile
@@ -56,19 +56,22 @@
 #
 KBUILD_CFLAGS	+= $(call cc-option,-fno-ipa-sra)
 
+# Need -msoft-float for gcc 11 for the below instruction set selection
+KBUILD_CFLAGS	+= -msoft-float
+
 # This selects which instruction set is used.
 # Note that GCC does not numerically define an architecture version
 # macro, but instead defines a whole series of macros which makes
 # testing for a specific architecture or later rather impossible.
-arch-$(CONFIG_CPU_32v7M)	=-D__LINUX_ARM_ARCH__=7 -march=armv7-m -Wa,-march=armv7-m
-arch-$(CONFIG_CPU_32v7)		=-D__LINUX_ARM_ARCH__=7 $(call cc-option,-march=armv7-a,-march=armv5t -Wa$(comma)-march=armv7-a)
-arch-$(CONFIG_CPU_32v6)		=-D__LINUX_ARM_ARCH__=6 $(call cc-option,-march=armv6,-march=armv5t -Wa$(comma)-march=armv6)
+arch-$(CONFIG_CPU_32v7M)	=-D__LINUX_ARM_ARCH__=7 -march=armv7-m
+arch-$(CONFIG_CPU_32v7)		=-D__LINUX_ARM_ARCH__=7 -march=armv7-a
+arch-$(CONFIG_CPU_32v6)		=-D__LINUX_ARM_ARCH__=6 -march=armv6
 # Only override the compiler option if ARMv6. The ARMv6K extensions are
 # always available in ARMv7
 ifeq ($(CONFIG_CPU_32v6),y)
-arch-$(CONFIG_CPU_32v6K)	=-D__LINUX_ARM_ARCH__=6 $(call cc-option,-march=armv6k,-march=armv5t -Wa$(comma)-march=armv6k)
+arch-$(CONFIG_CPU_32v6K)	=-D__LINUX_ARM_ARCH__=6 -march=armv6k
 endif
-arch-$(CONFIG_CPU_32v5)		=-D__LINUX_ARM_ARCH__=5 $(call cc-option,-march=armv5te,-march=armv4t)
+arch-$(CONFIG_CPU_32v5)		=-D__LINUX_ARM_ARCH__=5 -march=armv5te
 arch-$(CONFIG_CPU_32v4T)	=-D__LINUX_ARM_ARCH__=4 -march=armv4t
 arch-$(CONFIG_CPU_32v4)		=-D__LINUX_ARM_ARCH__=4 -march=armv4
 arch-$(CONFIG_CPU_32v3)		=-D__LINUX_ARM_ARCH__=3 -march=armv3m
@@ -82,7 +85,7 @@
 tune-$(CONFIG_CPU_ARM740T)	=-mtune=arm7tdmi
 tune-$(CONFIG_CPU_ARM9TDMI)	=-mtune=arm9tdmi
 tune-$(CONFIG_CPU_ARM940T)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_ARM946E)	=$(call cc-option,-mtune=arm9e,-mtune=arm9tdmi)
+tune-$(CONFIG_CPU_ARM946E)	=-mtune=arm9e
 tune-$(CONFIG_CPU_ARM920T)	=-mtune=arm9tdmi
 tune-$(CONFIG_CPU_ARM922T)	=-mtune=arm9tdmi
 tune-$(CONFIG_CPU_ARM925T)	=-mtune=arm9tdmi
@@ -90,11 +93,11 @@
 tune-$(CONFIG_CPU_FA526)	=-mtune=arm9tdmi
 tune-$(CONFIG_CPU_SA110)	=-mtune=strongarm110
 tune-$(CONFIG_CPU_SA1100)	=-mtune=strongarm1100
-tune-$(CONFIG_CPU_XSCALE)	=$(call cc-option,-mtune=xscale,-mtune=strongarm110) -Wa,-mcpu=xscale
-tune-$(CONFIG_CPU_XSC3)		=$(call cc-option,-mtune=xscale,-mtune=strongarm110) -Wa,-mcpu=xscale
-tune-$(CONFIG_CPU_FEROCEON)	=$(call cc-option,-mtune=marvell-f,-mtune=xscale)
-tune-$(CONFIG_CPU_V6)		=$(call cc-option,-mtune=arm1136j-s,-mtune=strongarm)
-tune-$(CONFIG_CPU_V6K)		=$(call cc-option,-mtune=arm1136j-s,-mtune=strongarm)
+tune-$(CONFIG_CPU_XSCALE)	=-mtune=xscale
+tune-$(CONFIG_CPU_XSC3)		=-mtune=xscale
+tune-$(CONFIG_CPU_FEROCEON)	=-mtune=xscale
+tune-$(CONFIG_CPU_V6)		=-mtune=arm1136j-s
+tune-$(CONFIG_CPU_V6K)		=-mtune=arm1136j-s
 
 # Evaluate tune cc-option calls now
 tune-y := $(tune-y)
@@ -125,7 +128,7 @@
 endif
 
 # Need -Uarm for gcc < 3.x
-KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(CFLAGS_ISA) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
+KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(CFLAGS_ISA) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -Uarm
 KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_ISA) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
 
 CHECKFLAGS	+= -D__arm__
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/compressed/efi-header.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/compressed/efi-header.S
@@ -9,16 +9,22 @@
 #include <linux/sizes.h>
 
 		.macro	__nop
-#ifdef CONFIG_EFI_STUB
-		@ This is almost but not quite a NOP, since it does clobber the
-		@ condition flags. But it is the best we can do for EFI, since
-		@ PE/COFF expects the magic string "MZ" at offset 0, while the
-		@ ARM/Linux boot protocol expects an executable instruction
-		@ there.
-		.inst	MZ_MAGIC | (0x1310 << 16)	@ tstne r0, #0x4d000
-#else
  AR_CLASS(	mov	r0, r0		)
   M_CLASS(	nop.w			)
+		.endm
+
+		.macro __initial_nops
+#ifdef CONFIG_EFI_STUB
+		@ This is a two-instruction NOP, which happens to bear the
+		@ PE/COFF signature "MZ" in the first two bytes, so the kernel
+		@ is accepted as an EFI binary. Booting via the UEFI stub
+		@ will not execute those instructions, but the ARM/Linux
+		@ boot protocol does, so we need some NOPs here.
+		.inst	MZ_MAGIC | (0xe225 << 16)	@ eor r5, r5, 0x4d000
+		eor	r5, r5, 0x4d000			@ undo previous insn
+#else
+		__nop
+		__nop
 #endif
 		.endm
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/compressed/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/compressed/head.S
@@ -203,7 +203,8 @@
 		 * were patching the initial instructions of the kernel, i.e
 		 * had started to exploit this "patch area".
 		 */
-		.rept	7
+		__initial_nops
+		.rept	5
 		__nop
 		.endr
 #ifndef CONFIG_THUMB2_KERNEL
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/compressed/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/compressed/vmlinux.lds.S
@@ -23,6 +23,7 @@
     *(.ARM.extab*)
     *(.note.*)
     *(.rel.*)
+    *(.printk_index)
     /*
      * Discard any r/w data - this produces a link error if we have any,
      * which is required for PIC decompression.  Local data generates
@@ -57,6 +58,7 @@
     *(.rodata)
     *(.rodata.*)
     *(.data.rel.ro)
+    *(.data.rel.ro.*)
   }
   .piggydata : {
     *(.piggydata)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/Makefile
@@ -127,6 +127,7 @@
 	bcm47094-luxul-xwr-3150-v1.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm47094-phicomm-k3.dtb \
+	bcm53015-meraki-mr26.dtb \
 	bcm53016-meraki-mr32.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
@@ -779,6 +780,7 @@
 	logicpd-som-lv-37xx-devkit.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-beagle-ab4.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-beagle-xm-ab.dtb \
 	omap3-cm-t3517.dtb \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -12,22 +12,20 @@
 	compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx";
 
 	/* Power */
-	regulators {
-		vcc3v3: fixedregulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "vcc3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-boot-on;
-		};
+	vcc3v3: fixedregulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
 
-		vcc1v8: fixedregulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "vcc1v8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-boot-on;
-		};
+	vcc1v8: fixedregulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
 	};
 
 	/* User IO */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am33xx-l4.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am33xx-l4.dtsi
@@ -1500,8 +1500,7 @@
 			mmc1: mmc@0 {
 				compatible = "ti,am335-sdhci";
 				ti,needs-special-reset;
-				dmas = <&edma_xbar 24 0 0
-					&edma_xbar 25 0 0>;
+				dmas = <&edma 24 0>, <&edma 25 0>;
 				dma-names = "tx", "rx";
 				interrupts = <64>;
 				reg = <0x0 0x1000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am33xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am33xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for AM33XX SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
@@ -352,6 +349,7 @@
 					<SYSC_IDLE_NO>,
 					<SYSC_IDLE_SMART>,
 					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-delay-us = <2>;
 			clocks = <&l3s_clkctrl AM3_L3S_USB_OTG_HS_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am3517-evm.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am3517-evm.dts
@@ -161,6 +161,8 @@
 
 	/* HS USB Host PHY on PORT 1 */
 	hsusb1_phy: hsusb1_phy {
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb1_rst_pins>;
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; /* gpio_57 */
 		#phy-cells = <0>;
@@ -168,7 +170,9 @@
 };
 
 &davinci_emac {
-	     status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_pins>;
+	status = "okay";
 };
 
 &davinci_mdio {
@@ -193,6 +197,8 @@
 };
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 	/* User DIP swithes [1:8] / User LEDS [1:2] */
 	tca6416: gpio@21 {
@@ -205,6 +211,8 @@
 };
 
 &i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
 };
 
@@ -223,6 +231,8 @@
 };
 
 &usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_pins>;
 	port1-mode = "ehci-phy";
 };
 
@@ -231,8 +241,35 @@
 };
 
 &omap3_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb1_rst_pins>;
+
+	ethernet_pins: pinmux_ethernet_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21fe, PIN_INPUT | MUX_MODE0) /* rmii_mdio_data */
+			OMAP3_CORE1_IOPAD(0x2200, MUX_MODE0) /* rmii_mdio_clk */
+			OMAP3_CORE1_IOPAD(0x2202, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd0 */
+			OMAP3_CORE1_IOPAD(0x2204, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd1 */
+			OMAP3_CORE1_IOPAD(0x2206, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_crs_dv */
+			OMAP3_CORE1_IOPAD(0x2208, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_rxer */
+			OMAP3_CORE1_IOPAD(0x220a, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd0 */
+			OMAP3_CORE1_IOPAD(0x220c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd1 */
+			OMAP3_CORE1_IOPAD(0x220e, PIN_OUTPUT_PULLDOWN |MUX_MODE0) /* rmii_txen */
+			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_scl */
+			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_scl */
+			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_sda */
+		>;
+	};
 
 	leds_pins: pinmux_leds_pins {
 		pinctrl-single,pins = <
@@ -300,8 +337,6 @@
 };
 
 &omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb1_pins>;
 
 	hsusb1_pins: pinmux_hsusb1_pins {
 		pinctrl-single,pins = <
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am3517-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am3517-som.dtsi
@@ -69,6 +69,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <400000>;
 
 	s35390a: s35390a@30 {
@@ -179,6 +181,13 @@
 
 &omap3_pmx_core {
 
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c1_scl */
+			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c1_sda */
+		>;
+	};
+
 	wl12xx_buffer_pins: pinmux_wl12xx_buffer_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4)  /* mmc1_dat7.gpio_129 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am3517.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am3517.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for am3517 SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap3.dtsi"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am4372.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am4372.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for AM4372 SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am5748.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am5748.dtsi
@@ -25,6 +25,10 @@
 	status = "disabled";
 };
 
+&usb4_tm {
+	status = "disabled";
+};
+
 &atl_tm {
 	status = "disabled";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
@@ -527,7 +527,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <31 0>;
-		pendown-gpio = <&gpio1 31 0>;
+		pendown-gpio = <&gpio1 31 GPIO_ACTIVE_LOW>;
 
 
 		ti,x-min = /bits/ 16 <0x0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/arm-realview-pb1176.dts
@@ -435,7 +435,7 @@
 
 		/* Direct-mapped development chip ROM */
 		pb1176_rom@10200000 {
-			compatible = "direct-mapped";
+			compatible = "mtd-rom";
 			reg = <0x10200000 0x4000>;
 			bank-width = <1>;
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-370.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-370.dtsi
@@ -74,7 +74,7 @@
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x80000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-375.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-375.dtsi
@@ -582,7 +582,7 @@
 
 			pcie1: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-380.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-380.dtsi
@@ -79,7 +79,7 @@
 			/* x1 port */
 			pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -98,7 +98,7 @@
 			/* x1 port */
 			pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-385-turris-omnia.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-385-turris-omnia.dts
@@ -23,6 +23,12 @@
 		stdout-path = &uart0;
 	};
 
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+	};
+
 	memory {
 		device_type = "memory";
 		reg = <0x00000000 0x40000000>; /* 1024 MB */
@@ -450,7 +456,17 @@
 				};
 			};
 
-			/* port 6 is connected to eth0 */
+			ports@6 {
+				reg = <6>;
+				label = "cpu";
+				ethernet = <&eth0>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
 		};
 	};
 };
@@ -471,7 +487,7 @@
 		marvell,function = "spi0";
 	};
 
-	spi0cs1_pins: spi0cs1-pins {
+	spi0cs2_pins: spi0cs2-pins {
 		marvell,pins = "mpp26";
 		marvell,function = "spi0";
 	};
@@ -506,7 +522,7 @@
 		};
 	};
 
-	/* MISO, MOSI, SCLK and CS1 are routed to pin header CN11 */
+	/* MISO, MOSI, SCLK and CS2 are routed to pin header CN11 */
 };
 
 &uart0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-385.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-385.dtsi
@@ -84,7 +84,7 @@
 			/* x1 port */
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -103,7 +103,7 @@
 			/* x1 port */
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -125,7 +125,7 @@
 			 */
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x48000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-38x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-38x.dtsi
@@ -168,7 +168,7 @@
 			};
 
 			uart0: serial@12000 {
-				compatible = "marvell,armada-38x-uart";
+				compatible = "marvell,armada-38x-uart", "ns16550a";
 				reg = <0x12000 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
@@ -178,7 +178,7 @@
 			};
 
 			uart1: serial@12100 {
-				compatible = "marvell,armada-38x-uart";
+				compatible = "marvell,armada-38x-uart", "ns16550a";
 				reg = <0x12100 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-39x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-39x.dtsi
@@ -453,7 +453,7 @@
 			/* x1 port */
 			pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -472,7 +472,7 @@
 			/* x1 port */
 			pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -494,7 +494,7 @@
 			 */
 			pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x48000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -97,7 +97,7 @@
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -115,7 +115,7 @@
 
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -133,7 +133,7 @@
 
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -151,7 +151,7 @@
 
 			pcie5: pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -112,7 +112,7 @@
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -130,7 +130,7 @@
 
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -148,7 +148,7 @@
 
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -166,7 +166,7 @@
 
 			pcie5: pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -184,7 +184,7 @@
 
 			pcie6: pcie@6,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+				assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -202,7 +202,7 @@
 
 			pcie7: pcie@7,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+				assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -220,7 +220,7 @@
 
 			pcie8: pcie@8,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+				assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -238,7 +238,7 @@
 
 			pcie9: pcie@9,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/artpec6-devboard.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/artpec6-devboard.dts
@@ -1,10 +1,5 @@
-/*
- * Axis ARTPEC-6 development board.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Axis ARTPEC-6 development board.
 
 /dts-v1/;
 #include "artpec6.dtsi"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-ast2500-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-ast2500-evb.dts
@@ -5,7 +5,7 @@
 
 / {
 	model = "AST2500 EVB";
-	compatible = "aspeed,ast2500";
+	compatible = "aspeed,ast2500-evb", "aspeed,ast2500";
 
 	aliases {
 		serial4 = &uart5;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts
@@ -5,6 +5,7 @@
 
 / {
 	model = "AST2600 A1 EVB";
+	compatible = "aspeed,ast2600-evb-a1", "aspeed,ast2600";
 
 	/delete-node/regulator-vcc-sdhci0;
 	/delete-node/regulator-vcc-sdhci1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-ast2600-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-ast2600-evb.dts
@@ -8,7 +8,7 @@
 
 / {
 	model = "AST2600 EVB";
-	compatible = "aspeed,ast2600";
+	compatible = "aspeed,ast2600-evb-a1", "aspeed,ast2600";
 
 	aliases {
 		serial4 = &uart5;
@@ -103,7 +103,7 @@
 &mac0 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethphy0>;
 
 	pinctrl-names = "default";
@@ -114,7 +114,7 @@
 &mac1 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethphy1>;
 
 	pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts
@@ -63,7 +63,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
-		spi-max-frequency = <100000000>; /* 100 MHz */
+		spi-max-frequency = <50000000>; /* 50 MHz */
 #include "openbmc-flash-layout.dtsi"
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
@@ -231,6 +231,21 @@
 			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+				 &pinctrl_adc10_default &pinctrl_adc11_default
+				 &pinctrl_adc12_default &pinctrl_adc13_default
+				 &pinctrl_adc14_default &pinctrl_adc15_default>;
 };
 
 &gpio0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -246,6 +246,21 @@
 			linux,code = <11>;
 		};
 	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
 };
 
 &ehci1 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
@@ -117,11 +117,6 @@
 		groups = "FWSPID";
 	};
 
-	pinctrl_fwqspid_default: fwqspid_default {
-		function = "FWQSPID";
-		groups = "FWQSPID";
-	};
-
 	pinctrl_fwspiwp_default: fwspiwp_default {
 		function = "FWSPIWP";
 		groups = "FWSPIWP";
@@ -653,12 +648,12 @@
 	};
 
 	pinctrl_qspi1_default: qspi1_default {
-		function = "QSPI1";
+		function = "SPI1";
 		groups = "QSPI1";
 	};
 
 	pinctrl_qspi2_default: qspi2_default {
-		function = "QSPI2";
+		function = "SPI2";
 		groups = "QSPI2";
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/aspeed-g6.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -364,6 +364,41 @@
 				status = "disabled";
 			};
 
+			adc0: adc@1e6e9000 {
+				compatible = "aspeed,ast2600-adc0";
+				reg = <0x1e6e9000 0x100>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				resets = <&syscon ASPEED_RESET_ADC>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				#io-channel-cells = <1>;
+				status = "disabled";
+			};
+
+			adc1: adc@1e6e9100 {
+				compatible = "aspeed,ast2600-adc1";
+				reg = <0x1e6e9100 0x100>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				resets = <&syscon ASPEED_RESET_ADC>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				#io-channel-cells = <1>;
+				status = "disabled";
+			};
+
+			sbc: secure-boot-controller@1e6f2000 {
+				compatible = "aspeed,ast2600-sbc";
+				reg = <0x1e6f2000 0x1000>;
+			};
+
+			video: video@1e700000 {
+				compatible = "aspeed,ast2600-video-engine";
+				reg = <0x1e700000 0x1000>;
+				clocks = <&syscon ASPEED_CLK_GATE_VCLK>,
+					 <&syscon ASPEED_CLK_GATE_ECLK>;
+				clock-names = "vclk", "eclk";
+				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
 			gpio0: gpio@1e780000 {
 				#gpio-cells = <2>;
 				gpio-controller;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -233,10 +233,9 @@
 		status = "okay";
 
 		eeprom@53 {
-			compatible = "atmel,24c32";
+			compatible = "atmel,24c02";
 			reg = <0x53>;
 			pagesize = <16>;
-			size = <128>;
 			status = "okay";
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
@@ -68,8 +68,8 @@
 		regulators {
 			vdd_3v3: VDD_IO {
 				regulator-name = "VDD_IO";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -87,8 +87,8 @@
 
 			vddio_ddr: VDD_DDR {
 				regulator-name = "VDD_DDR";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1850000>;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -110,8 +110,8 @@
 
 			vdd_core: VDD_CORE {
 				regulator-name = "VDD_CORE";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1850000>;
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -152,8 +152,8 @@
 
 			LDO1 {
 				regulator-name = "LDO1";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 
 				regulator-state-standby {
@@ -167,9 +167,8 @@
 
 			LDO2 {
 				regulator-name = "LDO2";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
-				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
 
 				regulator-state-standby {
 					regulator-on-in-suspend;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-sama5d2_icp.dts
@@ -197,8 +197,8 @@
 			regulators {
 				vdd_io_reg: VDD_IO {
 					regulator-name = "VDD_IO";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -216,8 +216,8 @@
 
 				VDD_DDR {
 					regulator-name = "VDD_DDR";
-					regulator-min-microvolt = <600000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -235,8 +235,8 @@
 
 				VDD_CORE {
 					regulator-name = "VDD_CORE";
-					regulator-min-microvolt = <600000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1250000>;
+					regulator-max-microvolt = <1250000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -258,7 +258,6 @@
 					regulator-max-microvolt = <1850000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
-					regulator-always-on;
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
@@ -273,8 +272,8 @@
 
 				LDO1 {
 					regulator-name = "LDO1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -288,8 +287,8 @@
 
 				LDO2 {
 					regulator-name = "LDO2";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -323,21 +322,21 @@
 	status = "okay";
 
 	eeprom@50 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 		status = "okay";
 	};
 
 	eeprom@52 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x52>;
 		pagesize = <16>;
 		status = "disabled";
 	};
 
 	eeprom@53 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x53>;
 		pagesize = <16>;
 		status = "disabled";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -57,8 +57,8 @@
 			};
 
 			spi0: spi@f0004000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi0_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi0_cs>;
 				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
 			};
@@ -171,8 +171,8 @@
 			};
 
 			spi1: spi@f8008000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi1_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioC 25 0>;
 				status = "okay";
 			};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -81,8 +81,8 @@
 			};
 
 			spi1: spi@fc018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi0_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioB 21 0>;
 				status = "okay";
 			};
@@ -140,7 +140,7 @@
 						atmel,pins =
 							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
 					};
-					pinctrl_spi0_cs: spi0_cs_default {
+					pinctrl_spi1_cs: spi1_cs_default {
 						atmel,pins =
 							<AT91_PIOB 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
 					};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-sama7g5ek.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-sama7g5ek.dts
@@ -169,8 +169,8 @@
 			regulators {
 				vdd_3v3: VDD_IO {
 					regulator-name = "VDD_IO";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -188,8 +188,8 @@
 
 				vddioddr: VDD_DDR {
 					regulator-name = "VDD_DDR";
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1450000>;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -209,8 +209,8 @@
 
 				vddcore: VDD_CORE {
 					regulator-name = "VDD_CORE";
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -228,8 +228,8 @@
 
 				vddcpu: VDD_OTHER {
 					regulator-name = "VDD_OTHER";
-					regulator-min-microvolt = <1125000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1250000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-ramp-delay = <3125>;
@@ -248,8 +248,8 @@
 
 				vldo1: LDO1 {
 					regulator-name = "LDO1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -403,7 +403,7 @@
 	pinctrl_flx3_default: flx3_default {
 		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
 			 <PIN_PD17__FLEXCOM3_IO1>;
-		bias-disable;
+		bias-pull-up;
 	};
 
 	pinctrl_flx4_default: flx4_default {
@@ -659,7 +659,7 @@
 };
 
 &shdwc {
-	atmel,shdwc-debouncer = <976>;
+	debounce-delay-us = <976>;
 	status = "okay";
 
 	input@0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91-tse850-3.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91-tse850-3.dts
@@ -262,7 +262,7 @@
 &macb1 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rmii";
 
 	#address-cells = <1>;
 	#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91rm9200.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91rm9200.dtsi
@@ -660,7 +660,7 @@
 				compatible = "atmel,at91rm9200-udc";
 				reg = <0xfffb0000 0x4000>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>;
-				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>, <&pmc PMC_TYPE_SYSTEM 2>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>, <&pmc PMC_TYPE_SYSTEM 1>;
 				clock-names = "pclk", "hclk";
 				status = "disabled";
 			};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91sam9261ek.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91sam9261ek.dts
@@ -156,7 +156,7 @@
 					compatible = "ti,ads7843";
 					interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>;
 					spi-max-frequency = <3000000>;
-					pendown-gpio = <&pioC 2 GPIO_ACTIVE_HIGH>;
+					pendown-gpio = <&pioC 2 GPIO_ACTIVE_LOW>;
 
 					ti,x-min = /bits/ 16 <150>;
 					ti,x-max = /bits/ 16 <3830>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -39,6 +39,13 @@
 
 				};
 
+				usb1 {
+					pinctrl_usb1_vbus_gpio: usb1_vbus_gpio {
+						atmel,pins =
+							<AT91_PIOC 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PC5 GPIO */
+					};
+				};
+
 				mmc0_slot1 {
 					pinctrl_board_mmc0_slot1: mmc0_slot1-board {
 						atmel,pins =
@@ -84,6 +91,8 @@
 			};
 
 			usb1: gadget@fffa4000 {
+				pinctrl-0 = <&pinctrl_usb1_vbus_gpio>;
+				pinctrl-names = "default";
 				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
@@ -219,6 +228,12 @@
 		wm8731: wm8731@1b {
 			compatible = "wm8731";
 			reg = <0x1b>;
+
+			/* PCK0 at 12MHz */
+			clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			clock-names = "mclk";
+			assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			assigned-clock-rates = <12000000>;
 		};
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm-nsp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -77,7 +77,7 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
-	mpcore@19000000 {
+	mpcore-bus@19000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
@@ -219,7 +219,7 @@
 			status = "disabled";
 		};
 
-		sdio: sdhci@21000 {
+		sdio: mmc@21000 {
 			compatible = "brcm,sdhci-iproc-cygnus";
 			reg = <0x21000 0x100>;
 			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2711-rpi-400.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2711-rpi-400.dts
@@ -28,12 +28,12 @@
 &expgpio {
 	gpio-line-names = "BT_ON",
 			  "WL_ON",
-			  "",
+			  "PWR_LED_OFF",
 			  "GLOBAL_RESET",
 			  "VDD_SD_IO_SEL",
-			  "CAM_GPIO",
+			  "GLOBAL_SHUTDOWN",
 			  "SD_PWR_ON",
-			  "SD_OC_N";
+			  "SHUTDOWN_REQUEST";
 };
 
 &genet_mdio {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2711.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2711.dtsi
@@ -133,7 +133,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -144,7 +144,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -155,7 +155,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -166,7 +166,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -290,6 +290,7 @@
 
 		hvs: hvs@7e400000 {
 			compatible = "brcm,bcm2711-hvs";
+			reg = <0x7e400000 0x8000>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
@@ -449,8 +450,6 @@
 					  IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
 					  IRQ_TYPE_LEVEL_LOW)>;
-		/* This only applies to the ARMv7 stub */
-		arm,cpu-registers-not-fw-configured;
 	};
 
 	cpus: cpus {
@@ -458,12 +457,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/100095/0003
+		 * /Level-1-Memory-System/About-the-L1-memory-system?lang=en
+		 * Source for d/i-cache-size
+		 * https://www.raspberrypi.com/documentation/computers
+		 * /processors.html#bcm2711
+		 */
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a72";
 			reg = <0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu1: cpu@1 {
@@ -472,6 +485,13 @@
 			reg = <1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu2: cpu@2 {
@@ -480,6 +500,13 @@
 			reg = <2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu3: cpu@3 {
@@ -488,6 +515,28 @@
 			reg = <3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 *  https://developer.arm.com/documentation/100095/0003
+		 *  /Level-2-Memory-System/About-the-L2-memory-system?lang=en
+		 *  Source for d/i-cache-size
+		 *  https://www.raspberrypi.com/documentation/computers
+		 *  /processors.html#bcm2711
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set
+			cache-level = <2>;
 		};
 	};
 
@@ -506,11 +555,17 @@
 			#address-cells = <3>;
 			#interrupt-cells = <1>;
 			#size-cells = <2>;
-			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "pcie", "msi";
 			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
 			interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &gicv2 GIC_SPI 144
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &gicv2 GIC_SPI 145
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &gicv2 GIC_SPI 146
 							IRQ_TYPE_LEVEL_HIGH>;
 			msi-controller;
 			msi-parent = <&pcie0>;
@@ -576,6 +631,8 @@
 		     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
 
+	gpio-ranges = <&gpio 0 0 58>;
+
 	gpclk0_gpio49: gpclk0_gpio49 {
 		pin-gpclk {
 			pins = "gpio49";
@@ -1083,6 +1140,7 @@
 };
 
 &uart0 {
+	arm,primecell-periphid = <0x00341011>;
 	interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -53,18 +53,17 @@
 			  "GPIO18",
 			  "NC", /* GPIO19 */
 			  "NC", /* GPIO20 */
-			  "GPIO21",
+			  "CAM_GPIO0",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
 			  "NC", /* GPIO26 */
-			  "CAM_GPIO0",
-			  /* Binary number representing build/revision */
-			  "CONFIG0",
-			  "CONFIG1",
-			  "CONFIG2",
-			  "CONFIG3",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
 			  "NC", /* GPIO32 */
 			  "NC", /* GPIO33 */
 			  "NC", /* GPIO34 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
@@ -74,16 +74,18 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
 			  "CAM_GPIO1", /* GPIO40 */
 			  "WL_ON", /* GPIO41 */
 			  "NC", /* GPIO42 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -45,7 +45,7 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "BT_ON",
 				  "WL_ON",
-				  "STATUS_LED_R",
+				  "PWR_LED_R",
 				  "LAN_RUN",
 				  "",
 				  "CAM_GPIO0",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
@@ -63,8 +63,8 @@
 			  "GPIO43",
 			  "GPIO44",
 			  "GPIO45",
-			  "GPIO46",
-			  "GPIO47",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
 			  /* Used by eMMC */
 			  "SD_CLK_R",
 			  "SD_CMD_R",
@@ -77,7 +77,7 @@
 };
 
 &hdmi {
-	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&expgpio 0 GPIO_ACTIVE_LOW>;
 	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm2837.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm2837.dtsi
@@ -40,12 +40,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0500/e/level-1-memory-system
+		 * /about-the-l1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://magpi.raspberrypi.com/articles/raspberry-pi-3-specs-benchmarks
+		 */
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
 			reg = <0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu1: cpu@1 {
@@ -54,6 +68,13 @@
 			reg = <1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu2: cpu@2 {
@@ -62,6 +83,13 @@
 			reg = <2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu3: cpu@3 {
@@ -70,6 +98,27 @@
 			reg = <3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0500
+		 * /e/level-2-memory-system/about-the-l2-memory-system?lang=en
+		 * Source for cache-size
+		 * https://datasheets.raspberrypi.com/cm/cm1-and-cm3-datasheet.pdf
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>; // 512KiB(size)/64(line-size)=8192ways/16-way set
+			cache-level = <2>;
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm283x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm283x.dtsi
@@ -126,6 +126,8 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
+			gpio-ranges = <&gpio 0 0 54>;
+
 			/* Defines common pin muxing groups
 			 *
 			 * While each pin can have its mux selected
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
@@ -19,7 +19,8 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	gpio-keys {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
@@ -20,7 +20,7 @@
 		bootargs = "console=ttyS0,115200 earlycon";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x08000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
@@ -19,7 +19,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x08000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
@@ -19,7 +19,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x18000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
@@ -16,7 +16,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x08000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
@@ -19,7 +19,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x08000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
@@ -30,7 +30,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x08000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
@@ -15,7 +15,7 @@
 		bootargs = "console=ttyS0,115200 earlycon";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -129,7 +129,7 @@
 		};
 	};
 
-	mdio-bus-mux@18003000 {
+	mdio-mux@18003000 {
 
 		/* BIT(9) = 1 => external mdio */
 		mdio@200 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
@@ -16,7 +16,7 @@
 		bootargs = "earlycon";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>,
 		      <0x88000000 0x18000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
@@ -26,7 +26,6 @@
 		wlan {
 			label = "bcm53xx:blue:wlan";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "default-off";
 		};
 
 		system {
@@ -46,3 +45,16 @@
 		};
 	};
 };
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
@@ -26,7 +26,6 @@
 		5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-off";
 		};
 
 		system {
@@ -42,7 +41,6 @@
 		2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-off";
 		};
 	};
 
@@ -83,3 +81,16 @@
 		};
 	};
 };
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+	model = "Meraki MR26";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		key-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <50000000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&nandcs {
+	nand-ecc-algo = "hw";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x200000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x200000 0x200000>;
+			/* empty */
+		};
+
+		partition@400000 {
+			label = "u-boot-backup";
+			reg = <0x400000 0x200000>;
+			/* empty */
+		};
+
+		partition@600000 {
+			label = "u-boot-env-backup";
+			reg = <0x600000 0x200000>;
+			/* empty */
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+			label = "poe";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	ina219@40 {
+		compatible = "ti,ina219"; /* PoE power */
+		reg = <0x40>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* it's empty */
+	};
+};
+
+&thermal {
+	status = "disabled";
+	/* does not work, reads 418 degree Celsius */
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
@@ -20,7 +20,7 @@
 		bootargs = " console=ttyS0,115200n8 earlycon";
 	};
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x08000000>;
 		device_type = "memory";
 	};
@@ -195,3 +195,25 @@
 		};
 	};
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+			label = "poe";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm5301x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm5301x.dtsi
@@ -19,7 +19,7 @@
 	#size-cells = <1>;
 	interrupt-parent = <&gic>;
 
-	chipcommonA@18000000 {
+	chipcommon-a-bus@18000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x18000000 0x00001000>;
 		#address-cells = <1>;
@@ -44,7 +44,7 @@
 		};
 	};
 
-	mpcore@19000000 {
+	mpcore-bus@19000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
@@ -242,6 +242,8 @@
 
 			gpio-controller;
 			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		pcie0: pcie@12000 {
@@ -369,8 +371,8 @@
 		#address-cells = <1>;
 	};
 
-	mdio-bus-mux@18003000 {
-		compatible = "mdio-mux-mmioreg";
+	mdio-mux@18003000 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
 		mdio-parent-bus = <&mdio>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -408,27 +410,27 @@
 	i2c0: i2c@18009000 {
 		compatible = "brcm,iproc-i2c";
 		reg = <0x18009000 0x50>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clock-frequency = <100000>;
 		status = "disabled";
 	};
 
-	dmu@1800c000 {
+	dmu-bus@1800c000 {
 		compatible = "simple-bus";
 		ranges = <0 0x1800c000 0x1000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		cru@100 {
-			compatible = "simple-bus";
+		cru-bus@100 {
+			compatible = "brcm,ns-cru", "simple-mfd";
 			reg = <0x100 0x1a4>;
 			ranges;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			lcpll0: lcpll0@100 {
+			lcpll0: clock-controller@100 {
 				#clock-cells = <1>;
 				compatible = "brcm,nsp-lcpll0";
 				reg = <0x100 0x14>;
@@ -437,7 +439,7 @@
 						     "sdio", "ddr_phy";
 			};
 
-			genpll: genpll@140 {
+			genpll: clock-controller@140 {
 				#clock-cells = <1>;
 				compatible = "brcm,nsp-genpll";
 				reg = <0x140 0x24>;
@@ -448,7 +450,12 @@
 						     "sata1", "sata2";
 			};
 
-			pinctrl: pin-controller@1c0 {
+			syscon@180 {
+				compatible = "brcm,cru-clkset", "syscon";
+				reg = <0x180 0x4>;
+			};
+
+			pinctrl: pinctrl@1c0 {
 				compatible = "brcm,bcm4708-pinmux";
 				reg = <0x1c0 0x24>;
 				reg-names = "cru_gpio_control";
@@ -535,7 +542,6 @@
 				  "spi_lr_session_done",
 				  "spi_lr_overread";
 		clocks = <&iprocmed>;
-		clock-names = "iprocmed";
 		num-cs = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm53573.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm53573.dtsi
@@ -127,6 +127,9 @@
 
 		pcie0: pcie@2000 {
 			reg = <0x00002000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		usb2: usb2@4000 {
@@ -156,8 +159,6 @@
 			};
 
 			ohci: usb@d000 {
-				#usb-cells = <0>;
-
 				compatible = "generic-ohci";
 				reg = <0xd000 0x1000>;
 				interrupt-parent = <&gic>;
@@ -180,6 +181,24 @@
 
 		gmac0: ethernet@5000 {
 			reg = <0x5000 0x1000>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch: switch@1e {
+					compatible = "brcm,bcm53125";
+					reg = <0x1e>;
+
+					status = "disabled";
+
+					/* ports are defined in board DTS */
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+			};
 		};
 
 		gmac1: ethernet@b000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm94708.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm94708.dts
@@ -38,7 +38,7 @@
 	model = "NorthStar SVK (BCM94708)";
 	compatible = "brcm,bcm94708", "brcm,bcm4708";
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm94709.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm94709.dts
@@ -38,7 +38,7 @@
 	model = "NorthStar SVK (BCM94709)";
 	compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708";
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/bcm947189acdbmr.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/bcm947189acdbmr.dts
@@ -60,9 +60,9 @@
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 21 0>;
-		gpio-miso = <&chipcommon 22 0>;
-		gpio-mosi = <&chipcommon 23 0>;
+		sck-gpios = <&chipcommon 21 0>;
+		miso-gpios = <&chipcommon 22 0>;
+		mosi-gpios = <&chipcommon 23 0>;
 		cs-gpios = <&chipcommon 24 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dm814x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dm814x.dtsi
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
 #include <dt-bindings/bus/ti-sysc.h>
 #include <dt-bindings/clock/dm814.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dm816x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dm816x.dtsi
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
 #include <dt-bindings/bus/ti-sysc.h>
 #include <dt-bindings/clock/dm816.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dove.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dove.dtsi
@@ -129,7 +129,7 @@
 			pcie1: pcie@2 {
 				device_type = "pci";
 				status = "disabled";
-				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x80000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				clocks = <&gate_clk 5>;
 				marvell,pcie-port = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dra62x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dra62x.dtsi
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
 #include "dm814x.dtsi"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for DRA7x SoC DSPEVE thermal
  *
  * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dra7-iva-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dra7-iva-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for DRA7x SoC IVA thermal
  *
  * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dra7-l4.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dra7-l4.dtsi
@@ -12,6 +12,7 @@
 	ranges = <0x00000000 0x4a000000 0x100000>,	/* segment 0 */
 		 <0x00100000 0x4a100000 0x100000>,	/* segment 1 */
 		 <0x00200000 0x4a200000 0x100000>;	/* segment 2 */
+	dma-ranges;
 
 	segment@0 {					/* 0x4a000000 */
 		compatible = "simple-pm-bus";
@@ -557,6 +558,7 @@
 			 <0x0007e000 0x0017e000 0x001000>,	/* ap 124 */
 			 <0x00059000 0x00159000 0x001000>,	/* ap 125 */
 			 <0x0005a000 0x0015a000 0x001000>;	/* ap 126 */
+		dma-ranges;
 
 		target-module@2000 {			/* 0x4a102000, ap 27 3c.0 */
 			compatible = "ti,sysc";
@@ -3482,8 +3484,7 @@
 				ti,timer-pwm;
 			};
 		};
-
-		target-module@2c000 {			/* 0x4882c000, ap 17 02.0 */
+		timer15_target: target-module@2c000 {	/* 0x4882c000, ap 17 02.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
 			reg = <0x2c000 0x4>,
 			      <0x2c010 0x4>;
@@ -3511,7 +3512,7 @@
 			};
 		};
 
-		target-module@2e000 {			/* 0x4882e000, ap 19 14.0 */
+		timer16_target: target-module@2e000 {	/* 0x4882e000, ap 19 14.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
 			reg = <0x2e000 0x4>,
 			      <0x2e010 0x4>;
@@ -4189,11 +4190,11 @@
 			reg = <0x1d0010 0x4>;
 			reg-names = "sysc";
 			ti,sysc-midle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
+					<SYSC_IDLE_NO>;
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
 					<SYSC_IDLE_SMART>;
+			power-domains = <&prm_vpe>;
 			clocks = <&vpe_clkctrl DRA7_VPE_VPE_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/dra7.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/dra7.dtsi
@@ -144,7 +144,7 @@
 
 		l3-noc@44000000 {
 			compatible = "ti,dra7-l3-noc";
-			reg = <0x44000000 0x1000>,
+			reg = <0x44000000 0x1000000>,
 			      <0x45000000 0x1000>;
 			interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
 					      <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
@@ -1320,20 +1320,20 @@
 };
 
 /* Local timers, see ARM architected timer wrap erratum i940 */
-&timer3_target {
+&timer15_target {
 	ti,no-reset-on-init;
 	ti,no-idle;
 	timer@0 {
-		assigned-clocks = <&l4per_clkctrl DRA7_L4PER_TIMER3_CLKCTRL 24>;
+		assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>;
 		assigned-clock-parents = <&timer_sys_clk_div>;
 	};
 };
 
-&timer4_target {
+&timer16_target {
 	ti,no-reset-on-init;
 	ti,no-idle;
 	timer@0 {
-		assigned-clocks = <&l4per_clkctrl DRA7_L4PER_TIMER4_CLKCTRL 24>;
+		assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>;
 		assigned-clock-parents = <&timer_sys_clk_div>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/e60k02.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/e60k02.dtsi
@@ -302,6 +302,7 @@
 
 &usbotg1 {
 	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	disable-over-current;
 	srp-disable;
 	hnp-disable;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos3250-rinato.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -249,7 +249,7 @@
 	i80-if-timings {
 		cs-setup = <0>;
 		wr-setup = <0>;
-		wr-act = <1>;
+		wr-active = <1>;
 		wr-hold = <0>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4-cpu-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4-cpu-thermal.dtsi
@@ -10,7 +10,7 @@
 / {
 thermal-zones {
 	cpu_thermal: cpu-thermal {
-		thermal-sensors = <&tmu 0>;
+		thermal-sensors = <&tmu>;
 		polling-delay-passive = <0>;
 		polling-delay = <0>;
 		trips {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4.dtsi
@@ -605,7 +605,7 @@
 			status = "disabled";
 
 			hdmi_i2c_phy: hdmiphy@38 {
-				compatible = "exynos4210-hdmiphy";
+				compatible = "samsung,exynos4210-hdmiphy";
 				reg = <0x38>;
 			};
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4210-i9100.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4210-i9100.dts
@@ -200,8 +200,8 @@
 			power-on-delay = <10>;
 			reset-delay = <10>;
 
-			panel-width-mm = <90>;
-			panel-height-mm = <154>;
+			panel-width-mm = <56>;
+			panel-height-mm = <93>;
 
 			display-timings {
 				timing {
@@ -520,6 +520,14 @@
 				regulator-name = "VT_CAM_1.8V";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+
+				/*
+				 * Force-enable this regulator; otherwise the
+				 * kernel hangs very early in the boot process
+				 * for about 12 seconds, without apparent
+				 * reason.
+				 */
+				regulator-always-on;
 			};
 
 			vcclcd_reg: LDO13 {
@@ -827,7 +835,7 @@
 		compatible = "brcm,bcm4330-bt";
 
 		shutdown-gpios = <&gpl0 4 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpl1 0 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpl1 0 GPIO_ACTIVE_LOW>;
 		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
 		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -84,7 +84,7 @@
 &keypad {
 	samsung,keypad-num-rows = <2>;
 	samsung,keypad-num-columns = <8>;
-	linux,keypad-no-autorepeat;
+	linux,input-no-autorepeat;
 	wakeup-source;
 	pinctrl-names = "default";
 	pinctrl-0 = <&keypad_rows &keypad_cols>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4210.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4210.dtsi
@@ -393,7 +393,6 @@
 &cpu_thermal {
 	polling-delay-passive = <0>;
 	polling-delay = <0>;
-	thermal-sensors = <&tmu 0>;
 };
 
 &gic {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4412-itop-elite.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4412-itop-elite.dts
@@ -179,7 +179,7 @@
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
 		clocks = <&pmu_system_controller 0>;
-		clock-names = "MCLK1";
+		clock-names = "mclk";
 		wlf,shared-lrclk;
 		#sound-dai-cells = <0>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -585,7 +585,7 @@
 		clocks = <&camera 1>;
 		clock-names = "extclk";
 		samsung,camclk-out = <1>;
-		gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpm1 6 GPIO_ACTIVE_LOW>;
 
 		port {
 			is_s5k6a3_ep: endpoint {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4412-origen.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4412-origen.dts
@@ -95,7 +95,7 @@
 };
 
 &ehci {
-	samsung,vbus-gpio = <&gpx3 5 1>;
+	samsung,vbus-gpio = <&gpx3 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 	phys = <&exynos_usbphy 2>, <&exynos_usbphy 3>;
 	phy-names = "hsic0", "hsic1";
@@ -448,7 +448,7 @@
 &keypad {
 	samsung,keypad-num-rows = <3>;
 	samsung,keypad-num-columns = <2>;
-	linux,keypad-no-autorepeat;
+	linux,input-no-autorepeat;
 	wakeup-source;
 	pinctrl-0 = <&keypad_rows &keypad_cols>;
 	pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos4412-smdk4412.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos4412-smdk4412.dts
@@ -65,7 +65,7 @@
 &keypad {
 	samsung,keypad-num-rows = <3>;
 	samsung,keypad-num-columns = <8>;
-	linux,keypad-no-autorepeat;
+	linux,input-no-autorepeat;
 	wakeup-source;
 	pinctrl-0 = <&keypad_rows &keypad_cols>;
 	pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
@@ -260,7 +260,7 @@
 	};
 
 	uart3_data: uart3-data {
-		samsung,pins = "gpa1-4", "gpa1-4";
+		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -118,6 +118,9 @@
 	status = "okay";
 	ddc = <&i2c_2>;
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+	vdd-supply = <&ldo8_reg>;
+	vdd_osc-supply = <&ldo10_reg>;
+	vdd_pll-supply = <&ldo8_reg>;
 };
 
 &i2c_0 {
@@ -126,7 +129,7 @@
 	samsung,i2c-max-bus-freq = <20000>;
 
 	eeprom@50 {
-		compatible = "samsung,s524ad0xd1";
+		compatible = "samsung,s524ad0xd1", "atmel,24c128";
 		reg = <0x50>;
 	};
 
@@ -286,7 +289,7 @@
 	samsung,i2c-max-bus-freq = <20000>;
 
 	eeprom@51 {
-		compatible = "samsung,s524ad0xd1";
+		compatible = "samsung,s524ad0xd1", "atmel,24c128";
 		reg = <0x51>;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5250.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5250.dtsi
@@ -1119,7 +1119,7 @@
 &cpu_thermal {
 	polling-delay-passive = <0>;
 	polling-delay = <0>;
-	thermal-sensors = <&tmu 0>;
+	thermal-sensors = <&tmu>;
 
 	cooling-maps {
 		map0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5410-odroidxu.dts
@@ -120,7 +120,6 @@
 };
 
 &cpu0_thermal {
-	thermal-sensors = <&tmu_cpu0 0>;
 	polling-delay-passive = <0>;
 	polling-delay = <0>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -124,6 +124,9 @@
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_hpd_irq>;
+	vdd-supply = <&ldo6_reg>;
+	vdd_osc-supply = <&ldo7_reg>;
+	vdd_pll-supply = <&ldo6_reg>;
 };
 
 &hsi2c_4 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5420.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5420.dtsi
@@ -602,7 +602,7 @@
 		};
 
 		mipi_phy: mipi-video-phy {
-			compatible = "samsung,s5pv210-mipi-video-phy";
+			compatible = "samsung,exynos5420-mipi-video-phy";
 			syscon = <&pmu_system_controller>;
 			#phy-cells = <1>;
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5422-odroidhc1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5422-odroidhc1.dts
@@ -29,7 +29,7 @@
 
 	thermal-zones {
 		cpu0_thermal: cpu0-thermal {
-			thermal-sensors = <&tmu_cpu0 0>;
+			thermal-sensors = <&tmu_cpu0>;
 			trips {
 				cpu0_alert0: cpu-alert-0 {
 					temperature = <70000>; /* millicelsius */
@@ -84,7 +84,7 @@
 			};
 		};
 		cpu1_thermal: cpu1-thermal {
-			thermal-sensors = <&tmu_cpu1 0>;
+			thermal-sensors = <&tmu_cpu1>;
 			trips {
 				cpu1_alert0: cpu-alert-0 {
 					temperature = <70000>;
@@ -128,7 +128,7 @@
 			};
 		};
 		cpu2_thermal: cpu2-thermal {
-			thermal-sensors = <&tmu_cpu2 0>;
+			thermal-sensors = <&tmu_cpu2>;
 			trips {
 				cpu2_alert0: cpu-alert-0 {
 					temperature = <70000>;
@@ -172,7 +172,7 @@
 			};
 		};
 		cpu3_thermal: cpu3-thermal {
-			thermal-sensors = <&tmu_cpu3 0>;
+			thermal-sensors = <&tmu_cpu3>;
 			trips {
 				cpu3_alert0: cpu-alert-0 {
 					temperature = <70000>;
@@ -216,7 +216,7 @@
 			};
 		};
 		gpu_thermal: gpu-thermal {
-			thermal-sensors = <&tmu_gpu 0>;
+			thermal-sensors = <&tmu_gpu>;
 			trips {
 				gpu_alert0: gpu-alert-0 {
 					temperature = <70000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -50,7 +50,7 @@
 
 	thermal-zones {
 		cpu0_thermal: cpu0-thermal {
-			thermal-sensors = <&tmu_cpu0 0>;
+			thermal-sensors = <&tmu_cpu0>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -139,7 +139,7 @@
 			};
 		};
 		cpu1_thermal: cpu1-thermal {
-			thermal-sensors = <&tmu_cpu1 0>;
+			thermal-sensors = <&tmu_cpu1>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -212,7 +212,7 @@
 			};
 		};
 		cpu2_thermal: cpu2-thermal {
-			thermal-sensors = <&tmu_cpu2 0>;
+			thermal-sensors = <&tmu_cpu2>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -285,7 +285,7 @@
 			};
 		};
 		cpu3_thermal: cpu3-thermal {
-			thermal-sensors = <&tmu_cpu3 0>;
+			thermal-sensors = <&tmu_cpu3>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -358,7 +358,7 @@
 			};
 		};
 		gpu_thermal: gpu-thermal {
-			thermal-sensors = <&tmu_gpu 0>;
+			thermal-sensors = <&tmu_gpu>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/gemini-nas4220b.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/gemini-nas4220b.dts
@@ -84,7 +84,7 @@
 			partitions {
 				compatible = "redboot-fis";
 				/* Eraseblock at 0xfe0000 */
-				fis-index-block = <0x1fc>;
+				fis-index-block = <0x7f>;
 			};
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx1-ads.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx1-ads.dts
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <4>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx1-apf9328.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx1-apf9328.dts
@@ -45,7 +45,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx1.dtsi
@@ -268,9 +268,12 @@
 			status = "disabled";
 		};
 
-		esram: esram@300000 {
+		esram: sram@300000 {
 			compatible = "mmio-sram";
 			reg = <0x00300000 0x20000>;
+			ranges = <0 0x00300000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx23-evk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx23-evk.dts
@@ -79,7 +79,6 @@
 						MX23_PAD_LCD_RESET__GPIO_1_18
 						MX23_PAD_PWM3__GPIO_1_29
 						MX23_PAD_PWM4__GPIO_1_30
-						MX23_PAD_SSP1_DETECT__SSP1_DETECT
 					>;
 					fsl,drive-strength = <MXS_DRIVE_4mA>;
 					fsl,voltage = <MXS_VOLTAGE_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx23-sansa.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx23-sansa.dts
@@ -175,10 +175,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio1 24 0		/* SDA */
-			&gpio1 22 0		/* SCL */
-		>;
+		sda-gpios = <&gpio1 24 0>;
+		scl-gpios = <&gpio1 22 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 
@@ -186,10 +184,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio0 31 0		/* SDA */
-			&gpio0 30 0		/* SCL */
-		>;
+		sda-gpios = <&gpio0 31 0>;
+		scl-gpios = <&gpio0 30 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 
 		touch: touch@20 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx23.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx23.dtsi
@@ -59,7 +59,7 @@
 				reg = <0x80000000 0x2000>;
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
 				reg = <0x80004000 0x2000>;
 				interrupts = <0 14 20 0
@@ -414,7 +414,7 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
 				reg = <0x80024000 0x2000>;
 				interrupts = <7 5 9 26
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi
@@ -27,7 +27,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&qvga_timings>;
-			qvga_timings: 320x240 {
+			qvga_timings: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_svga_timings>;
-			dvi_svga_timings: 800x600 {
+			dvi_svga_timings: timing0 {
 				clock-frequency = <40000000>;
 				hactive = <800>;
 				vactive = <600>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_vga_timings>;
-			dvi_vga_timings: 640x480 {
+			dvi_vga_timings: timing0 {
 				clock-frequency = <31250000>;
 				hactive = <640>;
 				vactive = <480>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx25-pdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx25-pdk.dts
@@ -78,7 +78,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&wvga_timings>;
-			wvga_timings: 640x480 {
+			wvga_timings: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <45>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx25.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx25.dtsi
@@ -515,7 +515,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx25-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 112>, <&clks 68>;
@@ -543,7 +543,7 @@
 			};
 
 			iim: efuse@53ff0000 {
-				compatible = "fsl,imx25-iim", "fsl,imx27-iim";
+				compatible = "fsl,imx25-iim";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <19>;
 				clocks = <&clks 99>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27-apf27dev.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27-apf27dev.dts
@@ -16,7 +16,7 @@
 		fsl,pcr = <0xfae80083>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 800x480 {
+			timing0: timing0 {
 				clock-frequency = <33000033>;
 				hactive = <800>;
 				vactive = <480>;
@@ -47,7 +47,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi
@@ -33,7 +33,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -90,7 +90,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts
@@ -16,7 +16,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 320x240 {
+			timing0: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
@@ -19,7 +19,7 @@
 		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 640x480 {
+			timing0: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <112>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
@@ -19,7 +19,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 240x320 {
+			timing0: timing0 {
 				clock-frequency = <5500000>;
 				hactive = <240>;
 				vactive = <320>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
@@ -322,7 +322,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx27.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx27.dtsi
@@ -588,6 +588,9 @@
 		iram: sram@ffff4c00 {
 			compatible = "mmio-sram";
 			reg = <0xffff4c00 0xb400>;
+			ranges = <0 0xffff4c00 0xb400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx28-evk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx28-evk.dts
@@ -129,7 +129,7 @@
 				pinctrl-0 = <&spi2_pins_a>;
 				status = "okay";
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
 					compatible = "sst,sst25vf016b", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx28-m28evk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx28-m28evk.dts
@@ -33,7 +33,7 @@
 				pinctrl-0 = <&spi2_pins_a>;
 				status = "okay";
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
 					compatible = "m25p80", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx28-sps1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx28-sps1.dts
@@ -51,7 +51,7 @@
 				pinctrl-0 = <&spi2_pins_a>;
 				status = "okay";
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
 					compatible = "everspin,mr25h256", "mr25h256";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx28-xea.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx28-xea.dts
@@ -8,6 +8,7 @@
 #include "imx28-lwe.dtsi"
 
 / {
+	model = "Liebherr XEA board";
 	compatible = "lwn,imx28-xea", "fsl,imx28";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx28.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx28.dtsi
@@ -78,7 +78,7 @@
 				status = "disabled";
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
 				reg = <0x80004000 0x2000>;
 				interrupts = <82 83 84 85
@@ -992,7 +992,7 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
 				reg = <0x80024000 0x2000>;
 				interrupts = <78 79 66 0
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx31.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx31.dtsi
@@ -297,7 +297,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx31-sdma";
 				reg = <0x53fd4000 0x4000>;
 				interrupts = <34>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx35.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx35.dtsi
@@ -284,7 +284,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx35-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 9>, <&clks 65>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx50.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx50.dtsi
@@ -421,7 +421,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx50-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx51.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx51.dtsi
@@ -498,7 +498,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@83fb0000 {
+			sdma: dma-controller@83fb0000 {
 				compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
 				reg = <0x83fb0000 0x4000>;
 				interrupts = <6>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx53-m53menlo.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -53,6 +53,31 @@
 		};
 	};
 
+	lvds-decoder {
+		compatible = "ti,ds90cf364a", "lvds-decoder";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_decoder_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_decoder_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+
 	panel {
 		compatible = "edt,etm0700g0dh6";
 		pinctrl-0 = <&pinctrl_display_gpio>;
@@ -61,7 +86,7 @@
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
+				remote-endpoint = <&lvds_decoder_out>;
 			};
 		};
 	};
@@ -450,7 +475,7 @@
 			reg = <2>;
 
 			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
+				remote-endpoint = <&lvds_decoder_in>;
 			};
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx53-ppd.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx53-ppd.dts
@@ -488,7 +488,7 @@
 	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx53.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx53.dtsi
@@ -710,7 +710,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
@@ -297,7 +297,11 @@
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
 	phy-handle = <&phy>;
-	clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&rmii_clk>,
+		 <&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
 	status = "okay";
 
 	mdio {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6dl-prtrvt.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6dl-prtrvt.dts
@@ -126,6 +126,10 @@
 	status = "disabled";
 };
 
+&usbotg {
+	disable-over-current;
+};
+
 &vpu {
 	status = "disabled";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6dl-rex-basic.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6dl-rex-basic.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -105,8 +105,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <20>;
 	phy-supply = <&sw2_reg>;
 	status = "okay";
 
@@ -119,17 +117,10 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy_port2: phy@1 {
-			reg = <1>;
-		};
-
-		phy_port3: phy@2 {
-			reg = <2>;
-		};
-
 		switch@10 {
 			compatible = "qca,qca8334";
-			reg = <10>;
+			reg = <0x10>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 
 			switch_ports: ports {
 				#address-cells = <1>;
@@ -150,15 +141,30 @@
 				eth2: port@2 {
 					reg = <2>;
 					label = "eth2";
+					phy-mode = "internal";
 					phy-handle = <&phy_port2>;
 				};
 
 				eth1: port@3 {
 					reg = <3>;
 					label = "eth1";
+					phy-mode = "internal";
 					phy-handle = <&phy_port3>;
 				};
 			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_port2: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy_port3: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6dl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6dl.dtsi
@@ -84,6 +84,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-ba16.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-ba16.dtsi
@@ -142,7 +142,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: n25q032@0 {
+	flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-bx50v3.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-bx50v3.dtsi
@@ -160,7 +160,7 @@
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: flash@0 {
 		compatible = "atmel,at25";
 		spi-max-frequency = <10000000>;
 		size = <0x8000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -260,7 +260,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
@@ -102,7 +102,7 @@
 	cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80", "jedec,spi-nor";
 		spi-max-frequency = <40000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-dms-ba16.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-dms-ba16.dts
@@ -47,7 +47,7 @@
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: flash@0 {
 		compatible = "atmel,at25256B", "atmel,at25";
 		spi-max-frequency = <20000000>;
 		size = <0x8000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-gk802.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-gk802.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2013 Philipp Zabel
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Philipp Zabel
 
 /dts-v1/;
 #include <dt-bindings/gpio/gpio.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-gw5400-a.dts
@@ -137,7 +137,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,w25q256", "jedec,spi-nor";
 		spi-max-frequency = <30000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
@@ -5,31 +5,8 @@
 
 #include "imx6q.dtsi"
 #include "imx6qdl-kontron-samx6i.dtsi"
-#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Kontron SMARC sAMX6i Quad/Dual";
 	compatible = "kontron,imx6q-samx6i", "fsl,imx6q";
 };
-
-/* Quad/Dual SoMs have 3 chip-select signals */
-&ecspi4 {
-	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>,
-		   <&gpio3 29 GPIO_ACTIVE_LOW>,
-		   <&gpio3 25 GPIO_ACTIVE_LOW>;
-};
-
-&pinctrl_ecspi4 {
-	fsl,pins = <
-		MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
-		MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
-		MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
-
-		/* SPI4_IMX_CS2# - connected to internal flash */
-		MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x1b0b0
-		/* SPI4_IMX_CS0# - connected to SMARC SPI0_CS0# */
-		MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
-		/* SPI4_CS3# - connected to  SMARC SPI0_CS1# */
-		MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x1b0b0
-	>;
-};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-marsboard.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-marsboard.dts
@@ -100,7 +100,7 @@
 	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-prti6q.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-prti6q.dts
@@ -364,8 +364,8 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_wifi>;
 		interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
-		ref-clock-frequency = "38400000";
-		tcxo-clock-frequency = "19200000";
+		ref-clock-frequency = <38400000>;
+		tcxo-clock-frequency = <19200000>;
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q-rex-pro.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q-rex-pro.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf032b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6q.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6q.dtsi
@@ -163,6 +163,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -286,6 +286,8 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
@@ -516,8 +518,6 @@
 			MX6QDL_PAD_DISP0_DAT21__AUD4_TXD	0x130b0
 			MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS	0x130b0
 			MX6QDL_PAD_DISP0_DAT23__AUD4_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
 		>;
 	};
 
@@ -810,6 +810,12 @@
 		>;
 	};
 
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1	0x130b0
+		>;
+	};
+
 	pinctrl_spdif: spdifgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_16__SPDIF_IN  0x1b0b0
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
@@ -96,7 +96,7 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
@@ -131,7 +131,7 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
@@ -132,7 +132,7 @@
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
-	pinctrl-0 = <&pinctrl_i2c2_gpio>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
 	scl-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
@@ -488,7 +488,7 @@
 		>;
 	};
 
-	pinctrl_i2c2_gpio: i2c2grp {
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x4001b8b1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
@@ -35,7 +35,7 @@
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "sst,sst25vf040b", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
@@ -632,7 +632,6 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
 	rts-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
@@ -29,7 +29,7 @@
 
 		user-pb {
 			label = "user_pb";
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
@@ -26,7 +26,7 @@
 
 		user-pb {
 			label = "user_pb";
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
@@ -51,16 +51,6 @@
 		vin-supply = <&reg_3p3v_s5>;
 	};
 
-	reg_3p3v_s0: regulator-3p3v-s0 {
-		compatible = "regulator-fixed";
-		regulator-name = "V_3V3_S0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_3p3v_s5>;
-	};
-
 	reg_3p3v_s5: regulator-3p3v-s5 {
 		compatible = "regulator-fixed";
 		regulator-name = "V_3V3_S5";
@@ -254,12 +244,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>,
-		   <&gpio3 29 GPIO_ACTIVE_LOW>;
+		   <&gpio3 29 GPIO_ACTIVE_LOW>,
+		   <&gpio3 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	/* default boot source: workaround #1 for errata ERR006282 */
-	smarc_flash: spi-flash@0 {
-		compatible = "winbond,w25q16dw", "jedec,spi-nor";
+	smarc_flash: flash@0 {
+		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <20000000>;
 	};
@@ -269,8 +260,24 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
 };
 
 &i2c_intern {
@@ -397,7 +404,7 @@
 
 /* HDMI_CTRL */
 &i2c2 {
-	clock-frequency = <375000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 };
@@ -458,6 +465,8 @@
 			MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x1b0b0
 			/* SPI_IMX_CS0# - connected to SMARC SPI0_CS0# */
 			MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+			/* SPI4_CS3# - connected to SMARC SPI0_CS1# */
+			MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x1b0b0
 		>;
 	};
 
@@ -510,7 +519,7 @@
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC         0x1b0b0
 			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25    0x1b0b0 /* RST_GBE0_PHY# */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01       0x1b0b0 /* RST_GBE0_PHY# */
 		>;
 	};
 
@@ -723,7 +732,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
 	wake-up-gpio = <&gpio6 18 GPIO_ACTIVE_HIGH>;
-	reset-gpio = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	reset-gpio = <&gpio3 13 GPIO_ACTIVE_LOW>;
 };
 
 /* LCD_BKLT_PWM */
@@ -811,5 +820,6 @@
 	/* CPLD is feeded by watchdog (hardwired) */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
@@ -179,7 +179,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
@@ -321,7 +321,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
@@ -252,7 +252,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
@@ -237,7 +237,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -69,6 +69,7 @@
 	vbus-supply = <&reg_usb_h1_vbus>;
 	phy_type = "utmi";
 	dr_mode = "host";
+	disable-over-current;
 	status = "okay";
 };
 
@@ -78,10 +79,18 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
-	disable-over-current;
+	over-current-active-low;
 	status = "okay";
 };
 
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -272,7 +272,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
 	status = "disabled"; /* pin conflict with WEIM NOR */
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -313,7 +313,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -197,7 +197,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
@@ -226,7 +226,7 @@
 		reg = <0x28>;
 		#gpio-cells = <2>;
 		gpio-controller;
-		ngpio = <32>;
+		ngpios = <62>;
 	};
 
 	sgtl5000: codec@a {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-udoo.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-udoo.dtsi
@@ -5,6 +5,8 @@
  * Author: Fabio Estevam <fabio.estevam@freescale.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	aliases {
 		backlight = &backlight;
@@ -226,6 +228,7 @@
 				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
 			>;
 		};
 
@@ -304,7 +307,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	non-removable;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -309,6 +309,7 @@
 
 		ethphy: ethernet-phy@1 {
 			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qdl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qdl.dtsi
@@ -150,7 +150,7 @@
 		interrupt-parent = <&gpc>;
 		ranges;
 
-		dma_apbh: dma-apbh@110000 {
+		dma_apbh: dma-controller@110000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x00110000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
@@ -763,7 +763,7 @@
 					regulator-name = "vddpu";
 					regulator-min-microvolt = <725000>;
 					regulator-max-microvolt = <1450000>;
-					regulator-enable-ramp-delay = <150>;
+					regulator-enable-ramp-delay = <380>;
 					anatop-reg-offset = <0x140>;
 					anatop-vol-bit-shift = <9>;
 					anatop-vol-bit-width = <5>;
@@ -930,7 +930,7 @@
 				interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6qp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6qp.dtsi
@@ -9,12 +9,18 @@
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sl-evk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sl-evk.dts
@@ -137,7 +137,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
@@ -597,6 +597,7 @@
 
 &usbotg1 {
 	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	disable-over-current;
 	srp-disable;
 	hnp-disable;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sl.dtsi
@@ -117,6 +117,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
@@ -749,7 +752,7 @@
 				interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sl-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sll.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sll.dtsi
@@ -51,20 +51,18 @@
 			device_type = "cpu";
 			reg = <0>;
 			next-level-cache = <&L2>;
-			operating-points = <
+			operating-points =
 				/* kHz    uV */
-				996000  1275000
-				792000  1175000
-				396000  1075000
-				198000	975000
-			>;
-			fsl,soc-operating-points = <
+				<996000  1275000>,
+				<792000  1175000>,
+				<396000  1075000>,
+				<198000	  975000>;
+			fsl,soc-operating-points =
 				/* ARM kHz      SOC-PU uV */
-				996000          1175000
-				792000          1175000
-				396000          1175000
-				198000		1175000
-			>;
+				<996000         1175000>,
+				<792000         1175000>,
+				<396000         1175000>,
+				<198000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SLL_CLK_ARM>,
@@ -117,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -551,7 +552,7 @@
 				reg = <0x020ca000 0x1000>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SLL_CLK_USBPHY2>;
-				phy-reg_3p0-supply = <&reg_3p0>;
+				phy-3p0-supply = <&reg_3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
@@ -107,7 +107,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sx-sdb-reva.dts
@@ -123,7 +123,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: s25fl128s@0 {
+	flash0: flash@0 {
 		reg = <0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -133,7 +133,7 @@
 		spi-tx-bus-width = <4>;
 	};
 
-	flash1: s25fl128s@2 {
+	flash1: flash@2 {
 		reg = <2>;
 		#address-cells = <1>;
 		#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sx-sdb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -108,7 +108,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
@@ -118,7 +118,7 @@
 		reg = <0>;
 	};
 
-	flash1: n25q256a@2 {
+	flash1: flash@2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6sx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6sx.dtsi
@@ -164,12 +164,18 @@
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
@@ -203,7 +209,7 @@
 			power-domains = <&pd_pu>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
@@ -842,7 +848,7 @@
 				reg = <0x020e4000 0x4000>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sx-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -975,6 +981,8 @@
 					 <&clks IMX6SX_CLK_USDHC1>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
 				status = "disabled";
 			};
 
@@ -987,6 +995,8 @@
 					 <&clks IMX6SX_CLK_USDHC2>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
 				status = "disabled";
 			};
 
@@ -999,6 +1009,8 @@
 					 <&clks IMX6SX_CLK_USDHC3>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
 				status = "disabled";
 			};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -286,7 +286,7 @@
 	pinctrl-0 = <&pinctrl_qspi>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
@@ -19,7 +19,7 @@
 };
 
 &qspi {
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "spi-nand";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
@@ -18,7 +18,7 @@
 };
 
 &qspi {
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "spi-nand";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
@@ -19,7 +19,7 @@
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul-pico-dwarf.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul-pico-dwarf.dts
@@ -32,7 +32,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul-pico.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul-pico.dtsi
@@ -121,6 +121,8 @@
 			max-speed = <100>;
 			interrupt-parent = <&gpio5>;
 			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ul.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ul.dtsi
@@ -64,20 +64,18 @@
 			clock-frequency = <696000000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
-			operating-points = <
+			operating-points =
 				/* kHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1025000
-				198000	950000
-			>;
-			fsl,soc-operating-points = <
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1025000>,
+				<198000	950000>;
+			fsl,soc-operating-points =
 				/* KHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1175000
-				198000	1175000
-			>;
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1175000>,
+				<198000	1175000>;
 			clocks = <&clks IMX6UL_CLK_ARM>,
 				 <&clks IMX6UL_CLK_PLL2_BUS>,
 				 <&clks IMX6UL_CLK_PLL2_PFD2>,
@@ -149,6 +147,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -163,7 +164,7 @@
 			      <0x00a06000 0x2000>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
@@ -543,7 +544,7 @@
 			};
 
 			kpp: keypad@20b8000 {
-				compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
+				compatible = "fsl,imx6ul-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_KPP>;
@@ -743,7 +744,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
 					     "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
@@ -998,7 +999,7 @@
 			};
 
 			csi: csi@21c4000 {
-				compatible = "fsl,imx6ul-csi", "fsl,imx7-csi";
+				compatible = "fsl,imx6ul-csi";
 				reg = <0x021c4000 0x4000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_CSI>;
@@ -1007,7 +1008,7 @@
 			};
 
 			lcdif: lcdif@21c8000 {
-				compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx6ul-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x021c8000 0x4000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_LCDIF_PIX>,
@@ -1028,7 +1029,7 @@
 			qspi: spi@21e0000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
+				compatible = "fsl,imx6ul-qspi";
 				reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
 				reg-names = "QuadSPI", "QuadSPI-memory";
 				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -37,7 +37,7 @@
 
 	reg_sd1_vmmc: regulator-sd1-vmmc {
 		compatible = "regulator-gpio";
-		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_snvs_reg_sd>;
 		regulator-always-on;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
@@ -18,7 +18,7 @@
 };
 
 &qspi {
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "spi-nand";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx6ull-pinfunc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx6ull-pinfunc.h
@@ -82,6 +82,6 @@
 #define MX6ULL_PAD_CSI_DATA04__ESAI_TX_FS                         0x01F4 0x0480 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA05__ESAI_TX_CLK                        0x01F8 0x0484 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA06__ESAI_TX5_RX0                       0x01FC 0x0488 0x0000 0x9 0x0
-#define MX6ULL_PAD_CSI_DATA07__ESAI_T0                            0x0200 0x048C 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA07__ESAI_TX0                           0x0200 0x048C 0x0000 0x9 0x0
 
 #endif /* __DTS_IMX6ULL_PINFUNC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7-colibri.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -40,7 +40,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&codec>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -293,7 +293,7 @@
 		compatible = "fsl,sgtl5000";
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sai1_mclk>;
 		VDDA-supply = <&reg_module_3v3_avdd>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7-mba7.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7-mba7.dtsi
@@ -264,7 +264,7 @@
 	tlv320aic32x4: audio-codec@18 {
 		compatible = "ti,tlv320aic32x4";
 		reg = <0x18>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		ldoin-supply = <&reg_audio_3v3>;
 		iov-supply = <&reg_audio_3v3>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
@@ -13,6 +13,10 @@
 	};
 };
 
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
 &gpio6 {
 	gpio-line-names = "",
 			  "",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-nitrogen7.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-nitrogen7.dts
@@ -288,7 +288,7 @@
 	codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		wlf,shared-lrclk;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-pico-dwarf.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-pico-dwarf.dts
@@ -32,7 +32,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -52,7 +52,7 @@
 };
 
 &i2c4 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-pico-hobbit.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-pico-hobbit.dts
@@ -31,7 +31,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -41,7 +41,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_vref_1v8>;
 	};
@@ -64,7 +64,7 @@
 		interrupt-parent = <&gpio2>;
 		interrupts = <7 0>;
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio2 7 0>;
+		pendown-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_3p3v>;
 		ti,x-min = /bits/ 16 <0>;
 		ti,x-max = /bits/ 16 <4095>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-pico-nymph.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-pico-nymph.dts
@@ -43,7 +43,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -64,7 +64,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-pico-pi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-pico-pi.dts
@@ -31,7 +31,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -41,7 +41,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_vref_1v8>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-sdb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-sdb.dts
@@ -205,13 +205,8 @@
 		pinctrl-0 = <&pinctrl_tsc2046_pendown>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
-		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
@@ -385,14 +380,14 @@
 	codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		wlf,shared-lrclk;
 		wlf,hp-cfg = <2 2 3>;
 		wlf,gpio-cfg = <1 3>;
 		assigned-clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_SRC>,
 				  <&clks IMX7D_PLL_AUDIO_POST_DIV>,
-				  <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+				  <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
 		assigned-clock-rates = <0>, <884736000>, <12288000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d-zii-rmu2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d-zii-rmu2.dts
@@ -350,7 +350,7 @@
 
 &iomuxc_lpsr {
 	pinctrl_enet1_phy_interrupt: enet1phyinterruptgrp {
-		fsl,phy = <
+		fsl,pins = <
 			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x08
 		>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7d.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7d.dtsi
@@ -209,9 +209,6 @@
 };
 
 &ca_funnel_in_ports {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	port@1 {
 		reg = <1>;
 		ca_funnel_in_port1: endpoint {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7s-warp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7s-warp.dts
@@ -75,7 +75,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&codec>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -232,7 +232,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sai1_mclk>;
 		VDDA-supply = <&vgen4_reg>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7s.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7s.dtsi
@@ -104,6 +104,7 @@
 		compatible = "usb-nop-xceiv";
 		clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_hsic_phy>;
 		#phy-cells = <0>;
 	};
 
@@ -173,7 +174,11 @@
 			clock-names = "apb_pclk";
 
 			ca_funnel_in_ports: in-ports {
-				port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
 					ca_funnel_in_port0: endpoint {
 						remote-endpoint = <&etm0_out_port>;
 					};
@@ -437,7 +442,7 @@
 			};
 
 			gpt1: timer@302d0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302d0000 0x10000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT1_ROOT_CLK>,
@@ -446,7 +451,7 @@
 			};
 
 			gpt2: timer@302e0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302e0000 0x10000>;
 				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT2_ROOT_CLK>,
@@ -456,7 +461,7 @@
 			};
 
 			gpt3: timer@302f0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302f0000 0x10000>;
 				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT3_ROOT_CLK>,
@@ -466,7 +471,7 @@
 			};
 
 			gpt4: timer@30300000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x30300000 0x10000>;
 				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT4_ROOT_CLK>,
@@ -496,7 +501,7 @@
 
 				mux: mux-controller {
 					compatible = "mmio-mux";
-					#mux-control-cells = <0>;
+					#mux-control-cells = <1>;
 					mux-reg-masks = <0x14 0x00000010>;
 				};
 
@@ -797,7 +802,7 @@
 			};
 
 			lcdif: lcdif@30730000 {
-				compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx7d-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x30730000 0x10000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
@@ -1135,7 +1140,6 @@
 				compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
 				reg = <0x30b30000 0x200>;
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-				power-domains = <&pgc_hsic_phy>;
 				clocks = <&clks IMX7D_USB_CTRL_CLK>;
 				fsl,usbphy = <&usbphynop3>;
 				fsl,usbmisc = <&usbmisc3 0>;
@@ -1166,6 +1170,8 @@
 					<&clks IMX7D_USDHC1_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
@@ -1178,6 +1184,8 @@
 					<&clks IMX7D_USDHC2_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
@@ -1190,6 +1198,8 @@
 					<&clks IMX7D_USDHC3_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
@@ -1206,7 +1216,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@30bd0000 {
+			sdma: dma-controller@30bd0000 {
 				compatible = "fsl,imx7d-sdma", "fsl,imx35-sdma";
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -1239,14 +1249,13 @@
 			};
 		};
 
-		dma_apbh: dma-apbh@33000000 {
+		dma_apbh: dma-controller@33000000 {
 			compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x33000000 0x2000>;
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
@@ -1255,7 +1264,7 @@
 		gpmi: nand-controller@33002000{
 			compatible = "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/imx7ulp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/imx7ulp.dtsi
@@ -259,7 +259,7 @@
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_WDG1>;
 			assigned-clocks = <&pcc2 IMX7ULP_CLK_WDG1>;
-			assigned-clocks-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>;
 			timeout-sec = <40>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/integratorap.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/integratorap.dts
@@ -153,6 +153,7 @@
 
 	pci: pciv3@62000000 {
 		compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
+		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/iwg20d-q7-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/iwg20d-q7-common.dtsi
@@ -49,7 +49,7 @@
 	lcd_backlight: backlight {
 		compatible = "pwm-backlight";
 
-		pwms = <&pwm3 0 5000000 0>;
+		pwms = <&pwm3 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		enable-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/kirkwood-lsxl.dtsi
@@ -10,6 +10,11 @@
 
 	ocp@f1000000 {
 		pinctrl: pin-controller@10000 {
+			/* Non-default UART pins */
+			pmx_uart0: pmx-uart0 {
+				marvell,pins = "mpp4", "mpp5";
+			};
+
 			pmx_power_hdd: pmx-power-hdd {
 				marvell,pins = "mpp10";
 				marvell,function = "gpo";
@@ -213,22 +218,11 @@
 &mdio {
 	status = "okay";
 
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-
 	ethphy1: ethernet-phy@8 {
 		reg = <8>;
 	};
 };
 
-&eth0 {
-	status = "okay";
-	ethernet0-port@0 {
-		phy-handle = <&ethphy0>;
-	};
-};
-
 &eth1 {
 	status = "okay";
 	ethernet1-port@0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
@@ -11,3 +11,18 @@
 	model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
 	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
 };
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_2_pins>;
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
@@ -11,3 +11,18 @@
 	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
 	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
 };
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_2_pins>;
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/logicpd-som-lv.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/logicpd-som-lv.dtsi
@@ -265,21 +265,6 @@
 	};
 };
 
-&omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_2_pins>;
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
-		pinctrl-single,pins = <
-			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
-			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
-			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
-			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
-			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
-			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
-		>;
-	};
-};
-
 &uart2 {
 	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 	pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/ls1021a-tsn.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/ls1021a-tsn.dts
@@ -251,7 +251,7 @@
 
 	flash@0 {
 		/* Rev. A uses 64MB flash, Rev. B & C use 32MB flash */
-		compatible = "jedec,spi-nor", "s25fl256s1", "s25fl512s";
+		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/ls1021a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/ls1021a.dtsi
@@ -329,39 +329,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-
-				thermal-sensors = <&tmu 0>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-							<&cpu1 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		dspi0: spi@2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
@@ -1016,4 +983,37 @@
 			big-endian;
 		};
 	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/meson.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/meson.dtsi
@@ -59,7 +59,7 @@
 			};
 
 			uart_A: serial@84c0 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x84c0 0x18>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
 				fifo-size = <128>;
@@ -67,7 +67,7 @@
 			};
 
 			uart_B: serial@84dc {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x84dc 0x18>;
 				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -105,7 +105,7 @@
 			};
 
 			uart_C: serial@8700 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x8700 0x18>;
 				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -228,7 +228,7 @@
 			};
 
 			uart_AO: serial@4c0 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart", "amlogic,meson-ao-uart";
 				reg = <0x4c0 0x18>;
 				interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/meson8.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/meson8.dtsi
@@ -736,27 +736,27 @@
 };
 
 &uart_AO {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_CLK81>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart", "amlogic,meson-ao-uart";
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_A {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART0>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_B {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART1>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART2>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &usb0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/meson8b.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/meson8b.dtsi
@@ -724,27 +724,27 @@
 };
 
 &uart_AO {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_CLK81>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart", "amlogic,meson-ao-uart";
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_A {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART0>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_B {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART1>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART2>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &usb0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/mmp2-brownstone.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/mmp2-brownstone.dts
@@ -28,7 +28,7 @@
 &twsi1 {
 	status = "okay";
 	pmic: max8925@3c {
-		compatible = "maxium,max8925";
+		compatible = "maxim,max8925";
 		reg = <0x3c>;
 		interrupts = <1>;
 		interrupt-parent = <&intcmux4>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/motorola-mapphone-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/motorola-mapphone-common.dtsi
@@ -614,12 +614,12 @@
 /* Configure pwm clock source for timers 8 & 9 */
 &timer8 {
 	assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_clkin_ck>;
+	assigned-clock-parents = <&sys_32k_ck>;
 };
 
 &timer9 {
 	assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_clkin_ck>;
+	assigned-clock-parents = <&sys_32k_ck>;
 };
 
 /*
@@ -640,6 +640,7 @@
 &uart3 {
 	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
 			       &omap4_pmx_core 0x17c>;
+	overrun-throttle-ms = <500>;
 };
 
 &uart4 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/moxart-uc7112lx.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/moxart-uc7112lx.dts
@@ -79,7 +79,7 @@
 	clocks = <&ref12>;
 };
 
-&sdhci {
+&mmc {
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/moxart.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/moxart.dtsi
@@ -93,8 +93,8 @@
 			clock-names = "PCLK";
 		};
 
-		sdhci: sdhci@98e00000 {
-			compatible = "moxa,moxart-sdhci";
+		mmc: mmc@98e00000 {
+			compatible = "moxa,moxart-mmc";
 			reg = <0x98e00000 0x5C>;
 			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_apb>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/mt7623.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/mt7623.dtsi
@@ -309,7 +309,7 @@
 		clock-names = "spi", "wrap";
 	};
 
-	cir: cir@10013000 {
+	cir: ir-receiver@10013000 {
 		compatible = "mediatek,mt7623-cir";
 		reg = <0 0x10013000 0 0x1000>;
 		interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts
@@ -366,7 +366,7 @@
 		spi-max-frequency = <20000000>;
 		spi-rx-bus-width = <2>;
 		label = "bmc";
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts
@@ -142,7 +142,7 @@
 		reg = <0>;
 		spi-rx-bus-width = <2>;
 
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts
@@ -388,7 +388,7 @@
 		spi-max-frequency = <5000000>;
 		spi-rx-bus-width = <2>;
 		label = "bmc";
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -422,7 +422,7 @@
 		reg = <1>;
 		spi-max-frequency = <5000000>;
 		spi-rx-bus-width = <2>;
-		partitions@88000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -447,7 +447,7 @@
 		reg = <0>;
 		spi-max-frequency = <5000000>;
 		spi-rx-bus-width = <2>;
-		partitions@A0000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
@@ -74,7 +74,7 @@
 		spi-rx-bus-width = <2>;
 		reg = <0>;
 		spi-max-frequency = <5000000>;
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -135,7 +135,7 @@
 		spi-rx-bus-width = <2>;
 		reg = <0>;
 		spi-max-frequency = <5000000>;
-		partitions@A0000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts
@@ -107,7 +107,7 @@
 		reg = <0>;
 		spi-rx-bus-width = <2>;
 
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -146,7 +146,7 @@
 		reg = <1>;
 		npcm,fiu-rx-bus-width = <2>;
 
-		partitions@88000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -173,7 +173,7 @@
 		reg = <0>;
 		spi-rx-bus-width = <2>;
 
-		partitions@A0000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -8,9 +8,9 @@
 
 / {
 	vddvario: regulator-vddvario {
-		  compatible = "regulator-fixed";
-		  regulator-name = "vddvario";
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
 	};
 
 	vdd33a: regulator-vdd33a {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi
@@ -12,9 +12,9 @@
 
 / {
 	vddvario: regulator-vddvario {
-		  compatible = "regulator-fixed";
-		  regulator-name = "vddvario";
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
 	};
 
 	vdd33a: regulator-vdd33a {
@@ -29,7 +29,7 @@
 		compatible = "smsc,lan9221","smsc,lan9115";
 		bank-width = <2>;
 
-		gpmc,mux-add-data;
+		gpmc,mux-add-data = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <42>;
 		gpmc,cs-wr-off-ns = <36>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap2.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP2 SoC
  *
  * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap2420.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap2420.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP2420 SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap2.dtsi"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap2430.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap2430.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP243x SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap2.dtsi"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-beagle-ab4.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-beagle-ab4.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "omap3-beagle.dts"
+
+/ {
+	model = "TI OMAP3 BeagleBoard A to B4";
+	compatible = "ti,omap3-beagle-ab4", "ti,omap3-beagle", "ti,omap3430", "ti,omap3";
+};
+
+/*
+ * Workaround for capacitor C70 issue, see "Boards revision A and < B5"
+ * section at https://elinux.org/BeagleBoard_Community
+ */
+
+/* Unusable as clocksource because of unreliable oscillator */
+&counter32k {
+	status = "disabled";
+};
+
+/* Unusable as clockevent because of unreliable oscillator, allow to idle */
+&timer1_target {
+	/delete-property/ti,no-reset-on-init;
+	/delete-property/ti,no-idle;
+	timer@0 {
+		/delete-property/ti,timer-alwon;
+	};
+};
+
+/* Preferred always-on timer for clocksource */
+&timer12_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		/* Always clocked by secure_32k_fck */
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt2_fck>;
+		assigned-clock-parents = <&sys_ck>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-beagle.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-beagle.dts
@@ -304,39 +304,6 @@
 	phys = <0 &hsusb2_phy>;
 };
 
-/* Unusable as clocksource because of unreliable oscillator */
-&counter32k {
-	status = "disabled";
-};
-
-/* Unusable as clockevent because if unreliable oscillator, allow to idle */
-&timer1_target {
-	/delete-property/ti,no-reset-on-init;
-	/delete-property/ti,no-idle;
-	timer@0 {
-		/delete-property/ti,timer-alwon;
-	};
-};
-
-/* Preferred always-on timer for clocksource */
-&timer12_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		/* Always clocked by secure_32k_fck */
-	};
-};
-
-/* Preferred timer for clockevent */
-&timer2_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		assigned-clocks = <&gpt2_fck>;
-		assigned-clock-parents = <&sys_ck>;
-	};
-};
-
 &twl_gpio {
 	ti,use-leds;
 	/* pullups: BIT(1) */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-cm-t3517.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-cm-t3517.dts
@@ -11,12 +11,12 @@
 	model = "CompuLab CM-T3517";
 	compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
 
-	vmmc:  regulator-vmmc {
-                compatible = "regulator-fixed";
-                regulator-name = "vmmc";
-                regulator-min-microvolt = <3300000>;
-                regulator-max-microvolt = <3300000>;
-        };
+	vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
 	wl12xx_vmmc2: wl12xx_vmmc2 {
 		compatible = "regulator-fixed";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-cm-t3x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-cm-t3x.dtsi
@@ -227,7 +227,7 @@
 
 		interrupt-parent = <&gpio2>;
 		interrupts = <25 0>;		/* gpio_57 */
-		pendown-gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC CPU thermal
  *
  * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
@@ -15,8 +12,7 @@
 	polling-delay = <1000>; /* milliseconds */
 	coefficients = <0 20000>;
 
-			/* sensor       ID */
-	thermal-sensors = <&bandgap     0>;
+	thermal-sensors = <&bandgap>;
 
 	cpu_trips: trips {
 		cpu_alert0: cpu_alert {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-devkit8000-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-devkit8000-common.dtsi
@@ -158,6 +158,24 @@
 	status = "disabled";
 };
 
+/* Unusable as clockevent because if unreliable oscillator, allow to idle */
+&timer1_target {
+	/delete-property/ti,no-reset-on-init;
+	/delete-property/ti,no-idle;
+	timer@0 {
+		/delete-property/ti,timer-alwon;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer12_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		/* Always clocked by secure_32k_fck */
+	};
+};
+
 &twl_gpio {
 	ti,use-leds;
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi
@@ -54,7 +54,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <27 0>;		/* gpio_27 */
-		pendown-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-devkit8000.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-devkit8000.dts
@@ -14,36 +14,3 @@
 		display2 = &tv0;
 	};
 };
-
-/* Unusable as clocksource because of unreliable oscillator */
-&counter32k {
-	status = "disabled";
-};
-
-/* Unusable as clockevent because if unreliable oscillator, allow to idle */
-&timer1_target {
-	/delete-property/ti,no-reset-on-init;
-	/delete-property/ti,no-idle;
-	timer@0 {
-		/delete-property/ti,timer-alwon;
-	};
-};
-
-/* Preferred always-on timer for clocksource */
-&timer12_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		/* Always clocked by secure_32k_fck */
-	};
-};
-
-/* Preferred timer for clockevent */
-&timer2_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		assigned-clocks = <&gpt2_fck>;
-		assigned-clock-parents = <&sys_ck>;
-	};
-};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-gta04.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -31,6 +31,8 @@
 	aliases {
 		display0 = &lcd;
 		display1 = &tv0;
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
 	};
 
 	ldo_3v3: fixedregulator {
@@ -330,7 +332,7 @@
 			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
 			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
 		>;
-       };
+	};
 
 	gps_pins: pinmux_gps_pins {
 		pinctrl-single,pins = <
@@ -515,7 +517,7 @@
 		compatible = "bosch,bma180";
 		reg = <0x41>;
 		pinctrl-names = "default";
-		pintcrl-0 = <&bma180_pins>;
+		pinctrl-0 = <&bma180_pins>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
@@ -607,6 +609,22 @@
 	clock-frequency = <100000>;
 };
 
+&mcspi1 {
+	status = "disabled";
+};
+
+&mcspi2 {
+	status = "disabled";
+};
+
+&mcspi3 {
+	status = "disabled";
+};
+
+&mcspi4 {
+	status = "disabled";
+};
+
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
@@ -848,8 +866,8 @@
 };
 
 &hdqw1w {
-        pinctrl-names = "default";
-        pinctrl-0 = <&hdq_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdq_pins>;
 };
 
 /* image signal processor within OMAP3 SoC */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-gta04a5one.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-gta04a5one.dts
@@ -5,9 +5,11 @@
 
 #include "omap3-gta04a5.dts"
 
-&omap3_pmx_core {
+/ {
 	model = "Goldelico GTA04A5/Letux 2804 with OneNAND";
+};
 
+&omap3_pmx_core {
 	gpmc_pins: pinmux_gpmc_pins {
 		pinctrl-single,pins = <
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-ldp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-ldp.dts
@@ -301,5 +301,5 @@
 
 &vaux1 {
 	/* Needed for ads7846 */
-        regulator-name = "vcc";
+	regulator-name = "vcc";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
@@ -311,7 +311,7 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <8 0>;   /* boot6 / gpio_8 */
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_vcc3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tsc2048_pins>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-n900.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-n900.dts
@@ -8,6 +8,7 @@
 
 #include "omap34xx.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 /*
  * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
@@ -235,27 +236,27 @@
 		pinctrl-single,pins = <
 
 			/* address lines */
-                        OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a1.gpmc_a1 */
-                        OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a2.gpmc_a2 */
-                        OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a3.gpmc_a3 */
+			OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a1.gpmc_a1 */
+			OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a2.gpmc_a2 */
+			OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a3.gpmc_a3 */
 
 			/* data lines, gpmc_d0..d7 not muxable according to TRM */
-                        OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0)        /* gpmc_d8.gpmc_d8 */
-                        OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0)        /* gpmc_d9.gpmc_d9 */
-                        OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0)        /* gpmc_d10.gpmc_d10 */
-                        OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0)        /* gpmc_d11.gpmc_d11 */
-                        OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0)        /* gpmc_d12.gpmc_d12 */
-                        OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0)        /* gpmc_d13.gpmc_d13 */
-                        OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0)        /* gpmc_d14.gpmc_d14 */
-                        OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0)        /* gpmc_d15.gpmc_d15 */
+			OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0)        /* gpmc_d8.gpmc_d8 */
+			OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0)        /* gpmc_d9.gpmc_d9 */
+			OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0)        /* gpmc_d10.gpmc_d10 */
+			OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0)        /* gpmc_d11.gpmc_d11 */
+			OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0)        /* gpmc_d12.gpmc_d12 */
+			OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0)        /* gpmc_d13.gpmc_d13 */
+			OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0)        /* gpmc_d14.gpmc_d14 */
+			OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0)        /* gpmc_d15.gpmc_d15 */
 
 			/*
 			 * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
 			 * according to TRM. OneNAND seems to require PIN_INPUT on clock.
 			 */
-                        OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0)       /* gpmc_ncs1.gpmc_ncs1 */
-                        OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
-		>;
+			OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0)       /* gpmc_ncs1.gpmc_ncs1 */
+			OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
+			>;
 	};
 
 	i2c1_pins: pinmux_i2c1_pins {
@@ -630,63 +631,92 @@
 	};
 
 	lp5523: lp5523@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		compatible = "national,lp5523";
 		reg = <0x32>;
 		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
-		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
+		enable-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
 
-		chan0 {
+		led@0 {
+			reg = <0>;
 			chan-name = "lp5523:kb1";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan1 {
+		led@1 {
+			reg = <1>;
 			chan-name = "lp5523:kb2";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan2 {
+		led@2 {
+			reg = <2>;
 			chan-name = "lp5523:kb3";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan3 {
+		led@3 {
+			reg = <3>;
 			chan-name = "lp5523:kb4";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan4 {
+		led@4 {
+			reg = <4>;
 			chan-name = "lp5523:b";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan5 {
+		led@5 {
+			reg = <5>;
 			chan-name = "lp5523:g";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan6 {
+		led@6 {
+			reg = <6>;
 			chan-name = "lp5523:r";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan7 {
+		led@7 {
+			reg = <7>;
 			chan-name = "lp5523:kb5";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan8 {
+		led@8 {
+			reg = <8>;
 			chan-name = "lp5523:kb6";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 	};
 
@@ -708,12 +738,12 @@
 
 	si4713: si4713@63 {
 		compatible = "silabs,si4713";
-                reg = <0x63>;
+		reg = <0x63>;
 
-                interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
-                reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
-                vio-supply = <&vio>;
-                vdd-supply = <&vaux1>;
+		interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
+		reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
+		vio-supply = <&vio>;
+		vdd-supply = <&vaux1>;
 	};
 
 	bq24150a: bq24150a@6b {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
@@ -149,7 +149,7 @@
 
 		interrupt-parent = <&gpio4>;
 		interrupts = <18 0>;			/* gpio_114 */
-		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
@@ -160,7 +160,7 @@
 
 		interrupt-parent = <&gpio4>;
 		interrupts = <18 0>;			/* gpio_114 */
-		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi
@@ -22,7 +22,7 @@
 		compatible = "smsc,lan9221","smsc,lan9115";
 		bank-width = <2>;
 
-		gpmc,mux-add-data;
+		gpmc,mux-add-data = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <42>;
 		gpmc,cs-wr-off-ns = <36>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-pandora-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-pandora-common.dtsi
@@ -651,7 +651,7 @@
 		pinctrl-0 = <&penirq_pins>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <30 IRQ_TYPE_NONE>;	/* GPIO_94 */
-		pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio3 30 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&vaux4>;
 
 		ti,x-min = /bits/ 16 <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3-zoom3.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3-zoom3.dts
@@ -23,9 +23,9 @@
 	};
 
 	vddvario: regulator-vddvario {
-		  compatible = "regulator-fixed";
-		  regulator-name = "vddvario";
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
 	};
 
 	vdd33a: regulator-vdd33a {
@@ -84,28 +84,28 @@
 
 	uart1_pins: pinmux_uart1_pins {
 		pinctrl-single,pins = <
-                        OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0)		/* uart1_cts.uart1_cts */
-                        OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0)		/* uart1_rts.uart1_rts */
-                        OMAP3_CORE1_IOPAD(0x2182, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
-                        OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)		/* uart1_tx.uart1_tx */
+			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0)		/* uart1_cts.uart1_cts */
+			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0)		/* uart1_rts.uart1_rts */
+			OMAP3_CORE1_IOPAD(0x2182, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
+			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)		/* uart1_tx.uart1_tx */
 		>;
 	};
 
 	uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
-                        OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
-                        OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
-                        OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
-                        OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
+			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
+			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
 		>;
 	};
 
 	uart3_pins: pinmux_uart3_pins {
 		pinctrl-single,pins = <
-                        OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
-                        OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
-                        OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
-                        OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
+			OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
+			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
@@ -205,22 +205,22 @@
 };
 
 &uart1 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
 };
 
 &uart2 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
 };
 
 &uart3 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart3_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
 };
 
 &uart4 {
-       status = "disabled";
+	status = "disabled";
 };
 
 &usb_otg_hs {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap3.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap3.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC
  *
  * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap34xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap34xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP34xx/OMAP35xx SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap36xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap36xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP4/5 SoC CPU thermal
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
@@ -15,21 +12,24 @@
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <1000>; /* milliseconds */
 
-			/* sensor       ID */
-        thermal-sensors = <&bandgap     0>;
+	/*
+	 * See 44xx files for single sensor addressing, omap5 and dra7 need
+	 * also sensor ID for addressing.
+	 */
+	thermal-sensors = <&bandgap     0>;
 
 	cpu_trips: trips {
-                cpu_alert0: cpu_alert {
-                        temperature = <100000>; /* millicelsius */
-                        hysteresis = <2000>; /* millicelsius */
-                        type = "passive";
-                };
-                cpu_crit: cpu_crit {
-                        temperature = <125000>; /* millicelsius */
-                        hysteresis = <2000>; /* millicelsius */
-                        type = "critical";
-                };
-        };
+		cpu_alert0: cpu_alert {
+			temperature = <100000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu_crit: cpu_crit {
+			temperature = <125000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "critical";
+		};
+	};
 
 	cpu_cooling_maps: cooling-maps {
 		map0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap443x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap443x.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP443x SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap4.dtsi"
@@ -72,6 +69,7 @@
 };
 
 &cpu_thermal {
+	thermal-sensors = <&bandgap>;
 	coefficients = <0 20000>;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap4460.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap4460.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP4460 SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 #include "omap4.dtsi"
 
@@ -82,6 +79,7 @@
 };
 
 &cpu_thermal {
+	thermal-sensors = <&bandgap>;
 	coefficients = <348 (-9301)>;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap5-cm-t54.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap5-cm-t54.dts
@@ -84,36 +84,36 @@
 	};
 
 	lcd0: display {
-                compatible = "startek,startek-kd050c", "panel-dpi";
-                label = "lcd";
+		compatible = "startek,startek-kd050c", "panel-dpi";
+		label = "lcd";
 
-                pinctrl-names = "default";
-                pinctrl-0 = <&lcd_pins>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins>;
+
+		enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
 
-                enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+		panel-timing {
+			clock-frequency = <33000000>;
+			hactive = <800>;
+			vactive = <480>;
+			hfront-porch = <40>;
+			hback-porch = <40>;
+			hsync-len = <43>;
+			vback-porch = <29>;
+			vfront-porch = <13>;
+			vsync-len = <3>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
 
-                panel-timing {
-                        clock-frequency = <33000000>;
-                        hactive = <800>;
-                        vactive = <480>;
-                        hfront-porch = <40>;
-                        hback-porch = <40>;
-                        hsync-len = <43>;
-                        vback-porch = <29>;
-                        vfront-porch = <13>;
-                        vsync-len = <3>;
-                        hsync-active = <0>;
-                        vsync-active = <0>;
-                        de-active = <1>;
-                        pixelclk-active = <1>;
-                };
-
-                port {
-                        lcd_in: endpoint {
-                                remote-endpoint = <&dpi_lcd_out>;
-                        };
-                };
-        };
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_lcd_out>;
+			};
+		};
+	};
 
 	hdmi0: connector0 {
 		compatible = "hdmi-connector";
@@ -354,7 +354,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <15 0>;			/* gpio1_wk15 */
-		pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 15 GPIO_ACTIVE_LOW>;
 
 
 		ti,x-min = /bits/ 16 <0x0>;
@@ -644,8 +644,8 @@
 };
 
 &usb3 {
-       extcon = <&extcon_usb3>;
-       vbus-supply = <&smps10_out1_reg>;
+	extcon = <&extcon_usb3>;
+	vbus-supply = <&smps10_out1_reg>;
 };
 
 &cpu0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap5-core-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap5-core-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP543x SoC CORE thermal
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/omap5-gpu-thermal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/omap5-gpu-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP543x SoC GPU thermal
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi
@@ -28,7 +28,7 @@
 		label = "rofs";
 	};
 
-	rwfs@6000000 {
+	rwfs@2a00000 {
 		reg = <0x2a00000 0x1600000>; // 22MB
 		label = "rwfs";
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/openbmc-flash-layout.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/openbmc-flash-layout.dtsi
@@ -20,7 +20,7 @@
 		label = "kernel";
 	};
 
-	rofs@c0000 {
+	rofs@4c0000 {
 		reg = <0x4c0000 0x1740000>;
 		label = "rofs";
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /*
  * TODO: add Orion USB device port init when kernel.org support is added.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 #include "orion5x.dtsi"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #include "orion5x.dtsi"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 /dts-v1/;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /dts-v1/;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/orion5x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/orion5x.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/ox820.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/ox820.dtsi
@@ -287,7 +287,7 @@
 				clocks = <&armclk>;
 			};
 
-			gic: gic@1000 {
+			gic: interrupt-controller@1000 {
 				compatible = "arm,arm11mp-gic";
 				interrupt-controller;
 				#interrupt-cells = <3>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -760,7 +760,7 @@
 
 				xoadc: xoadc@197 {
 					compatible = "qcom,pm8921-adc";
-					reg = <197>;
+					reg = <0x197>;
 					interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
 					#address-cells = <2>;
 					#size-cells = <0>;
@@ -1571,7 +1571,7 @@
 		};
 
 		etb@1a01000 {
-			compatible = "coresight-etb10", "arm,primecell";
+			compatible = "arm,coresight-etb10", "arm,primecell";
 			reg = <0x1a01000 0x1000>;
 
 			clocks = <&rpmcc RPM_QDSS_CLK>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
@@ -11,9 +11,9 @@
 		dma@7984000 {
 			status = "okay";
 		};
-
-		qpic-nand@79b0000 {
-			status = "okay";
-		};
 	};
 };
+
+&nand {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
@@ -102,10 +102,10 @@
 			status = "okay";
 			perst-gpio = <&tlmm 38 0x1>;
 		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
-		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
@@ -65,11 +65,11 @@
 		dma@7984000 {
 			status = "okay";
 		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -142,7 +142,8 @@
 	clocks {
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+			clock-frequency = <32000>;
+			clock-output-names = "gcc_sleep_clk_src";
 			#clock-cells = <0>;
 		};
 
@@ -423,8 +424,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000>,
-				 <0x82000000 0 0x40300000 0x40300000 0 0x00d00000>;
+			ranges = <0x81000000 0x0 0x00000000 0x40200000 0x0 0x00100000>,
+				 <0x82000000 0x0 0x40300000 0x40300000 0x0 0x00d00000>;
 
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
@@ -19,12 +19,12 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory@0 {
+	memory@42000000 {
 		reg = <0x42000000 0x3e000000>;
 		device_type = "memory";
 	};
 
-	mdio0: mdio@0 {
+	mdio0: mdio-0 {
 		status = "okay";
 		compatible = "virtual,mdio-gpio";
 		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
@@ -91,7 +91,7 @@
 		};
 	};
 
-	mdio1: mdio@1 {
+	mdio1: mdio-1 {
 		status = "okay";
 		compatible = "virtual,mdio-gpio";
 		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -808,8 +808,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* MEM */
 
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
@@ -859,8 +859,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x31e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x2e000000 0x2e000000 0x0 0x03e00000>; /* MEM */
 
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
@@ -910,8 +910,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x35e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x32000000 0x32000000 0x0 0x03e00000>; /* MEM */
 
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-mdm9615.dtsi
@@ -82,14 +82,12 @@
 		};
 	};
 
-	regulators {
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
 	};
 
 	soc: soc {
@@ -324,6 +322,7 @@
 
 				pmicgpio: gpio@150 {
 					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
+					reg = <0x150>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
 					gpio-controller;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -146,7 +146,9 @@
 			reg		= <0x108000 0x1000>;
 			qcom,ipc	= <&l2cc 0x8 2>;
 
-			interrupts	= <0 19 0>, <0 21 0>, <0 22 0>;
+			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names	= "ack", "err", "wakeup";
 
 			regulators {
@@ -192,7 +194,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x16440000 0x1000>,
 				      <0x16400000 0x1000>;
-				interrupts = <0 154 0x0>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -318,7 +320,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x16080000 0x1000>;
-				interrupts = <0 147 0>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
 				spi-max-frequency = <24000000>;
 				cs-gpios = <&msmgpio 8 0>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -718,7 +718,7 @@
 		blsp2_uart7: serial@f995d000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xf995d000 0x1000>;
-			interrupts = <GIC_SPI 113 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP2_UART1_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
 			clock-names = "core", "iface";
 			status = "disabled";
@@ -1589,8 +1589,8 @@
 				#phy-cells = <0>;
 				qcom,dsi-phy-index = <0>;
 
-				clocks = <&mmcc MDSS_AHB_CLK>;
-				clock-names = "iface";
+				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
+				clock-names = "iface", "ref";
 			};
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-pm8841.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-pm8841.dtsi
@@ -25,6 +25,7 @@
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
 			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <0>;
 		};
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/qcom-sdx55.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/qcom-sdx55.dtsi
@@ -205,7 +205,7 @@
 		blsp1_uart3: serial@831000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x00831000 0x200>;
-			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc 30>,
 				 <&gcc 9>;
 			clock-names = "core", "iface";
@@ -334,12 +334,10 @@
 			clocks = <&rpmhcc RPMH_IPA_CLK>;
 			clock-names = "core";
 
-			interconnects = <&system_noc MASTER_IPA &system_noc SLAVE_SNOC_MEM_NOC_GC>,
-					<&mem_noc MASTER_SNOC_GC_MEM_NOC &mc_virt SLAVE_EBI_CH0>,
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI_CH0>,
 					<&system_noc MASTER_IPA &system_noc SLAVE_OCIMEM>,
 					<&mem_noc MASTER_AMPSS_M0 &system_noc SLAVE_IPA_CFG>;
-			interconnect-names = "memory-a",
-					     "memory-b",
+			interconnect-names = "memory",
 					     "imem",
 					     "config";
 
@@ -422,10 +420,10 @@
 					  <&gcc GCC_USB30_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
-			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 51 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 11 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 10 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -449,7 +447,7 @@
 			compatible = "qcom,sdx55-pdc", "qcom,pdc";
 			reg = <0x0b210000 0x30000>;
 			qcom,pdc-ranges = <0 179 52>;
-			#interrupt-cells = <3>;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&intc>;
 			interrupt-controller;
 		};
@@ -459,7 +457,7 @@
 			reg = <0x0c264000 0x1000>;
 		};
 
-		spmi_bus: qcom,spmi@c440000 {
+		spmi_bus: spmi@c440000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0c440000 0x0000d00>,
 			      <0x0c600000 0x2000000>,
@@ -504,7 +502,7 @@
 		};
 
 		apps_smmu: iommu@15000000 {
-			compatible = "qcom,sdx55-smmu-500", "arm,mmu-500";
+			compatible = "qcom,sdx55-smmu-500", "qcom,smmu-500", "arm,mmu-500";
 			reg = <0x15000000 0x20000>;
 			#iommu-cells = <2>;
 			#global-interrupts = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/r8a7792-blanche.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -239,7 +239,7 @@
 	};
 
 	keyboard_pins: keyboard {
-		pins = "GP_3_10", "GP_3_11", "GP_3_12", "GP_3_15", "GP_11_02";
+		pins = "GP_3_10", "GP_3_11", "GP_3_12", "GP_3_15", "GP_11_2";
 		bias-pull-up;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3036-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3036-evb.dts
@@ -31,11 +31,10 @@
 &i2c1 {
 	status = "okay";
 
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3036-kylin.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3036-kylin.dts
@@ -300,8 +300,8 @@
 &i2c2 {
 	status = "okay";
 
-	rt5616: rt5616@1b {
-		compatible = "rt5616";
+	rt5616: audio-codec@1b {
+		compatible = "realtek,rt5616";
 		reg = <0x1b>;
 		clocks = <&cru SCLK_I2S_OUT>;
 		clock-names = "mclk";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3036.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3036.dtsi
@@ -382,12 +382,13 @@
 		};
 	};
 
-	acodec: acodec-ana@20030000 {
-		compatible = "rk3036-codec";
+	acodec: audio-codec@20030000 {
+		compatible = "rockchip,rk3036-codec";
 		reg = <0x20030000 0x4000>;
-		rockchip,grf = <&grf>;
 		clock-names = "acodec_pclk";
 		clocks = <&cru PCLK_ACODEC>;
+		rockchip,grf = <&grf>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
@@ -397,17 +398,24 @@
 		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru  PCLK_HDMI>;
 		clock-names = "pclk";
-		rockchip,grf = <&grf>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&hdmi_ctl>;
 		status = "disabled";
 
-		hdmi_in: port {
+		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			hdmi_in_vop: endpoint@0 {
+
+			hdmi_in: port@0 {
 				reg = <0>;
-				remote-endpoint = <&vop_out_hdmi>;
+
+				hdmi_in_vop: endpoint {
+					remote-endpoint = <&vop_out_hdmi>;
+				};
+			};
+
+			hdmi_out: port@1 {
+				reg = <1>;
 			};
 		};
 	};
@@ -542,11 +550,11 @@
 	};
 
 	spi: spi@20074000 {
-		compatible = "rockchip,rockchip-spi";
+		compatible = "rockchip,rk3036-spi";
 		reg = <0x20074000 0x1000>;
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_SPI>, <&cru SCLK_SPI>;
-		clock-names = "apb-pclk","spi_pclk";
+		clocks = <&cru SCLK_SPI>, <&cru PCLK_SPI>;
+		clock-names = "spiclk", "apb_pclk";
 		dmas = <&pdma 8>, <&pdma 9>;
 		dma-names = "tx", "rx";
 		pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3066a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3066a.dtsi
@@ -124,6 +124,7 @@
 		pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>;
 		power-domains = <&power RK3066_PD_VIO>;
 		rockchip,grf = <&grf>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 
 		ports {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3188-radxarock.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3188-radxarock.dts
@@ -71,7 +71,7 @@
 		#sound-dai-cells = <0>;
 	};
 
-	ir_recv: gpio-ir-receiver {
+	ir_recv: ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3188.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3188.dtsi
@@ -378,7 +378,7 @@
 				rockchip,pins = <2 RK_PD3 1 &pcfg_pull_none>;
 			};
 
-			lcdc1_rgb24: ldcd1-rgb24 {
+			lcdc1_rgb24: lcdc1-rgb24 {
 				rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>,
 						<2 RK_PA1 1 &pcfg_pull_none>,
 						<2 RK_PA2 1 &pcfg_pull_none>,
@@ -606,7 +606,6 @@
 
 &global_timer {
 	interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
-	status = "disabled";
 };
 
 &local_timer {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk322x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk322x.dtsi
@@ -718,8 +718,8 @@
 		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 		assigned-clocks = <&cru SCLK_HDMI_PHY>;
 		assigned-clock-parents = <&hdmi_phy>;
-		clocks = <&cru SCLK_HDMI_HDCP>, <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_CEC>;
-		clock-names = "isfr", "iahb", "cec";
+		clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>, <&cru SCLK_HDMI_CEC>;
+		clock-names = "iahb", "isfr", "cec";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hdmii2c_xfer &hdmi_hpd &hdmi_cec>;
 		resets = <&cru SRST_HDMI_P>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3288-evb-act8846.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3288-evb-act8846.dts
@@ -54,7 +54,7 @@
 		vin-supply = <&vcc_sys>;
 	};
 
-	hym8563@51 {
+	rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3288-firefly.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3288-firefly.dtsi
@@ -233,11 +233,10 @@
 		vin-supply = <&vcc_sys>;
 	};
 
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 		interrupt-parent = <&gpio7>;
 		interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3288-miqi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3288-miqi.dts
@@ -162,11 +162,10 @@
 		vin-supply = <&vcc_sys>;
 	};
 
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3288-rock2-square.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3288-rock2-square.dts
@@ -165,11 +165,10 @@
 };
 
 &i2c0 {
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3288-vmarc-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3288-vmarc-som.dtsi
@@ -241,7 +241,6 @@
 		interrupt-parent = <&gpio5>;
 		interrupts = <RK_PC3 IRQ_TYPE_LEVEL_LOW>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "hym8563";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hym8563_int>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3288.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3288.dtsi
@@ -940,7 +940,7 @@
 		status = "disabled";
 	};
 
-	spdif: sound@ff88b0000 {
+	spdif: sound@ff8b0000 {
 		compatible = "rockchip,rk3288-spdif", "rockchip,rk3066-spdif";
 		reg = <0x0 0xff8b0000 0x0 0x10000>;
 		#sound-dai-cells = <0>;
@@ -971,7 +971,7 @@
 		status = "disabled";
 	};
 
-	crypto: cypto-controller@ff8a0000 {
+	crypto: crypto@ff8a0000 {
 		compatible = "rockchip,rk3288-crypto";
 		reg = <0x0 0xff8a0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
@@ -1180,6 +1180,7 @@
 		clock-names = "dp", "pclk";
 		phys = <&edp_phy>;
 		phy-names = "dp";
+		power-domains = <&power RK3288_PD_VIO>;
 		resets = <&cru SRST_EDP>;
 		reset-names = "dp";
 		rockchip,grf = <&grf>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/rk3xxx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/rk3xxx.dtsi
@@ -76,6 +76,13 @@
 		reg = <0x1013c200 0x20>;
 		interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
 		clocks = <&cru CORE_PERI>;
+		status = "disabled";
+		/* The clock source and the sched_clock provided by the arm_global_timer
+		 * on Rockchip rk3066a/rk3188 are quite unstable because their rates
+		 * depend on the CPU frequency.
+		 * Keep the arm_global_timer disabled in order to have the
+		 * DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
+		 */
 	};
 
 	local_timer: local-timer@1013c600 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/s3c6410-mini6410.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/s3c6410-mini6410.dts
@@ -51,7 +51,7 @@
 
 		ethernet@18000000 {
 			compatible = "davicom,dm9000";
-			reg = <0x18000000 0x2 0x18000004 0x2>;
+			reg = <0x18000000 0x2>, <0x18000004 0x2>;
 			interrupt-parent = <&gpn>;
 			interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
 			davicom,no-eeprom;
@@ -193,12 +193,12 @@
 };
 
 &pinctrl0 {
-	gpio_leds: gpio-leds {
+	gpio_leds: gpio-leds-pins {
 		samsung,pins = "gpk-4", "gpk-5", "gpk-6", "gpk-7";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	gpio_keys: gpio-keys {
+	gpio_keys: gpio-keys-pins {
 		samsung,pins = "gpn-0", "gpn-1", "gpn-2", "gpn-3",
 				"gpn-4", "gpn-5", "gpl-11", "gpl-12";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
@@ -16,111 +16,111 @@
 	 * Pin banks
 	 */
 
-	gpa: gpa {
+	gpa: gpa-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpc: gpc {
+	gpc: gpc-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpd: gpd {
+	gpd: gpd-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpe: gpe {
+	gpe: gpe-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpf: gpf {
+	gpf: gpf-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpg: gpg {
+	gpg: gpg-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gph: gph {
+	gph: gph-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpi: gpi {
+	gpi: gpi-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpj: gpj {
+	gpj: gpj-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpk: gpk {
+	gpk: gpk-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpl: gpl {
+	gpl: gpl-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpm: gpm {
+	gpm: gpm-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpn: gpn {
+	gpn: gpn-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpo: gpo {
+	gpo: gpo-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpp: gpp {
+	gpp: gpp-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpq: gpq {
+	gpq: gpq-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -131,225 +131,225 @@
 	 * Pin groups
 	 */
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa-0", "gpa-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa-2", "gpa-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa-4", "gpa-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa-6", "gpa-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ext_dma_0: ext-dma-0 {
+	ext_dma_0: ext-dma-0-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ext_dma_1: ext-dma-1 {
+	ext_dma_1: ext-dma-1-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_data_0: irda-data-0 {
+	irda_data_0: irda-data-0-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_data_1: irda-data-1 {
+	irda_data_1: irda-data-1-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_sdbw: irda-sdbw {
+	irda_sdbw: irda-sdbw-pins {
 		samsung,pins = "gpb-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb-5", "gpb-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_6>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpc-0", "gpc-1", "gpc-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi0_cs: spi0-cs {
+	spi0_cs: spi0-cs-pins {
 		samsung,pins = "gpc-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpc-4", "gpc-5", "gpc-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi1_cs: spi1-cs {
+	spi1_cs: spi1-cs-pins {
 		samsung,pins = "gpc-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpg-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpg-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_bus1: sd0-bus1 {
+	sd0_bus1: sd0-bus1-pins {
 		samsung,pins = "gpg-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_bus4: sd0-bus4 {
+	sd0_bus4: sd0-bus4-pins {
 		samsung,pins = "gpg-2", "gpg-3", "gpg-4", "gpg-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpg-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gph-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gph-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus1: sd1-bus1 {
+	sd1_bus1: sd1-bus1-pins {
 		samsung,pins = "gph-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus4: sd1-bus4 {
+	sd1_bus4: sd1-bus4-pins {
 		samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus8: sd1-bus8 {
+	sd1_bus8: sd1-bus8-pins {
 		samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5",
 				"gph-6", "gph-7", "gph-8", "gph-9";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpg-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_bus1: sd2-bus1 {
+	sd2_bus1: sd2-bus1-pins {
 		samsung,pins = "gph-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_bus4: sd2-bus4 {
+	sd2_bus4: sd2-bus4-pins {
 		samsung,pins = "gph-6", "gph-7", "gph-8", "gph-9";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s0_cdclk: i2s0-cdclk {
+	i2s0_cdclk: i2s0-cdclk-pins {
 		samsung,pins = "gpd-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s1_cdclk: i2s1-cdclk {
+	i2s1_cdclk: i2s1-cdclk-pins {
 		samsung,pins = "gpe-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpc-4", "gpc-5", "gpc-6", "gph-6",
 				"gph-8", "gph-9";
@@ -357,50 +357,50 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s2_cdclk: i2s2-cdclk {
+	i2s2_cdclk: i2s2-cdclk-pins {
 		/* S3C6410-only */
 		samsung,pins = "gph-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm0_extclk: pcm0-extclk {
+	pcm0_extclk: pcm0-extclk-pins {
 		samsung,pins = "gpd-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm1_extclk: pcm1-extclk {
+	pcm1_extclk: pcm1-extclk-pins {
 		samsung,pins = "gpe-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ac97_bus_0: ac97-bus-0 {
+	ac97_bus_0: ac97-bus-0-pins {
 		samsung,pins = "gpd-0", "gpd-1", "gpd-2", "gpd-3", "gpd-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ac97_bus_1: ac97-bus-1 {
+	ac97_bus_1: ac97-bus-1-pins {
 		samsung,pins = "gpe-0", "gpe-1", "gpe-2", "gpe-3", "gpe-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_port: cam-port {
+	cam_port: cam-port-pins {
 		samsung,pins = "gpf-0", "gpf-1", "gpf-2", "gpf-4",
 				"gpf-5", "gpf-6", "gpf-7", "gpf-8",
 				"gpf-9", "gpf-10", "gpf-11", "gpf-12";
@@ -408,242 +408,242 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_rst: cam-rst {
+	cam_rst: cam-rst-pins {
 		samsung,pins = "gpf-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_field: cam-field {
+	cam_field: cam-field-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpb-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm_extclk: pwm-extclk {
+	pwm_extclk: pwm-extclk-pins {
 		samsung,pins = "gpf-13";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpf-14";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpf-15";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	clkout0: clkout-0 {
+	clkout0: clkout-0-pins {
 		samsung,pins = "gpf-14";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col0_0: keypad-col0-0 {
+	keypad_col0_0: keypad-col0-0-pins {
 		samsung,pins = "gph-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col1_0: keypad-col1-0 {
+	keypad_col1_0: keypad-col1-0-pins {
 		samsung,pins = "gph-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col2_0: keypad-col2-0 {
+	keypad_col2_0: keypad-col2-0-pins {
 		samsung,pins = "gph-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col3_0: keypad-col3-0 {
+	keypad_col3_0: keypad-col3-0-pins {
 		samsung,pins = "gph-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col4_0: keypad-col4-0 {
+	keypad_col4_0: keypad-col4-0-pins {
 		samsung,pins = "gph-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col5_0: keypad-col5-0 {
+	keypad_col5_0: keypad-col5-0-pins {
 		samsung,pins = "gph-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col6_0: keypad-col6-0 {
+	keypad_col6_0: keypad-col6-0-pins {
 		samsung,pins = "gph-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col7_0: keypad-col7-0 {
+	keypad_col7_0: keypad-col7-0-pins {
 		samsung,pins = "gph-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col0_1: keypad-col0-1 {
+	keypad_col0_1: keypad-col0-1-pins {
 		samsung,pins = "gpl-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col1_1: keypad-col1-1 {
+	keypad_col1_1: keypad-col1-1-pins {
 		samsung,pins = "gpl-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col2_1: keypad-col2-1 {
+	keypad_col2_1: keypad-col2-1-pins {
 		samsung,pins = "gpl-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col3_1: keypad-col3-1 {
+	keypad_col3_1: keypad-col3-1-pins {
 		samsung,pins = "gpl-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col4_1: keypad-col4-1 {
+	keypad_col4_1: keypad-col4-1-pins {
 		samsung,pins = "gpl-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col5_1: keypad-col5-1 {
+	keypad_col5_1: keypad-col5-1-pins {
 		samsung,pins = "gpl-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col6_1: keypad-col6-1 {
+	keypad_col6_1: keypad-col6-1-pins {
 		samsung,pins = "gpl-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col7_1: keypad-col7-1 {
+	keypad_col7_1: keypad-col7-1-pins {
 		samsung,pins = "gpl-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row0_0: keypad-row0-0 {
+	keypad_row0_0: keypad-row0-0-pins {
 		samsung,pins = "gpk-8";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row1_0: keypad-row1-0 {
+	keypad_row1_0: keypad-row1-0-pins {
 		samsung,pins = "gpk-9";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row2_0: keypad-row2-0 {
+	keypad_row2_0: keypad-row2-0-pins {
 		samsung,pins = "gpk-10";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row3_0: keypad-row3-0 {
+	keypad_row3_0: keypad-row3-0-pins {
 		samsung,pins = "gpk-11";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row4_0: keypad-row4-0 {
+	keypad_row4_0: keypad-row4-0-pins {
 		samsung,pins = "gpk-12";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row5_0: keypad-row5-0 {
+	keypad_row5_0: keypad-row5-0-pins {
 		samsung,pins = "gpk-13";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row6_0: keypad-row6-0 {
+	keypad_row6_0: keypad-row6-0-pins {
 		samsung,pins = "gpk-14";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row7_0: keypad-row7-0 {
+	keypad_row7_0: keypad-row7-0-pins {
 		samsung,pins = "gpk-15";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row0_1: keypad-row0-1 {
+	keypad_row0_1: keypad-row0-1-pins {
 		samsung,pins = "gpn-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row1_1: keypad-row1-1 {
+	keypad_row1_1: keypad-row1-1-pins {
 		samsung,pins = "gpn-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row2_1: keypad-row2-1 {
+	keypad_row2_1: keypad-row2-1-pins {
 		samsung,pins = "gpn-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row3_1: keypad-row3-1 {
+	keypad_row3_1: keypad-row3-1-pins {
 		samsung,pins = "gpn-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row4_1: keypad-row4-1 {
+	keypad_row4_1: keypad-row4-1-pins {
 		samsung,pins = "gpn-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row5_1: keypad-row5-1 {
+	keypad_row5_1: keypad-row5-1-pins {
 		samsung,pins = "gpn-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row6_1: keypad-row6-1 {
+	keypad_row6_1: keypad-row6-1-pins {
 		samsung,pins = "gpn-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row7_1: keypad-row7-1 {
+	keypad_row7_1: keypad-row7-1-pins {
 		samsung,pins = "gpn-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpj-8", "gpj-9", "gpj-10", "gpj-11";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpi-3", "gpi-4", "gpi-5", "gpi-6",
 				"gpi-7", "gpi-10", "gpi-11", "gpi-12",
 				"gpi-13", "gpi-14", "gpi-15", "gpj-3",
@@ -652,7 +652,7 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpi-2", "gpi-3", "gpi-4", "gpi-5",
 				"gpi-6", "gpi-7", "gpi-10", "gpi-11",
 				"gpi-12", "gpi-13", "gpi-14", "gpi-15",
@@ -662,7 +662,7 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
 				"gpi-4", "gpi-5", "gpi-6", "gpi-7",
 				"gpi-8", "gpi-9", "gpi-10", "gpi-11",
@@ -673,7 +673,7 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	hsi_bus: hsi-bus {
+	hsi_bus: hsi-bus-pins {
 		samsung,pins = "gpk-0", "gpk-1", "gpk-2", "gpk-3",
 				"gpk-4", "gpk-5", "gpk-6", "gpk-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -564,7 +564,6 @@
 			reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
 			vdd3-supply = <&ldo7_reg>;
 			vci-supply = <&ldo17_reg>;
-			spi-cs-high;
 			spi-max-frequency = <1200000>;
 
 			pinctrl-names = "default";
@@ -636,7 +635,7 @@
 };
 
 &i2s0 {
-	dmas = <&pdma0 9>, <&pdma0 10>, <&pdma0 11>;
+	dmas = <&pdma0 10>, <&pdma0 9>, <&pdma0 11>;
 	status = "okay";
 };
 
@@ -895,7 +894,7 @@
 		device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
 		interrupt-parent = <&gph2>;
 		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "host-wake";
+		interrupt-names = "host-wakeup";
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/s5pv210-smdkv210.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/s5pv210-smdkv210.dts
@@ -41,7 +41,7 @@
 
 	ethernet@a8000000 {
 		compatible = "davicom,dm9000";
-		reg = <0xA8000000 0x2 0xA8000002 0x2>;
+		reg = <0xa8000000 0x2>, <0xa8000002 0x2>;
 		interrupt-parent = <&gph1>;
 		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 		local-mac-address = [00 00 de ad be ef];
@@ -55,6 +55,14 @@
 		default-brightness-level = <6>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm3_out>;
+		power-supply = <&dc5v_reg>;
+	};
+
+	dc5v_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "DC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/s5pv210.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/s5pv210.dtsi
@@ -239,8 +239,8 @@
 			reg = <0xeee30000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <16>;
-			dma-names = "rx", "tx", "tx-sec";
-			dmas = <&pdma1 9>, <&pdma1 10>, <&pdma1 11>;
+			dma-names = "tx", "rx", "tx-sec";
+			dmas = <&pdma1 10>, <&pdma1 9>, <&pdma1 11>;
 			clock-names = "iis",
 				      "i2s_opclk0",
 				      "i2s_opclk1";
@@ -259,8 +259,8 @@
 			reg = <0xe2100000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <17>;
-			dma-names = "rx", "tx";
-			dmas = <&pdma1 12>, <&pdma1 13>;
+			dma-names = "tx", "rx";
+			dmas = <&pdma1 13>, <&pdma1 12>;
 			clock-names = "iis", "i2s_opclk0";
 			clocks = <&clocks CLK_I2S1>, <&clocks SCLK_AUDIO1>;
 			pinctrl-names = "default";
@@ -274,8 +274,8 @@
 			reg = <0xe2a00000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <18>;
-			dma-names = "rx", "tx";
-			dmas = <&pdma1 14>, <&pdma1 15>;
+			dma-names = "tx", "rx";
+			dmas = <&pdma1 15>, <&pdma1 14>;
 			clock-names = "iis", "i2s_opclk0";
 			clocks = <&clocks CLK_I2S2>, <&clocks SCLK_AUDIO2>;
 			pinctrl-names = "default";
@@ -582,7 +582,7 @@
 				interrupts = <29>;
 				clocks = <&clocks CLK_CSIS>,
 						<&clocks SCLK_CSIS>;
-				clock-names = "clk_csis",
+				clock-names = "csis",
 						"sclk_csis";
 				bus-width = <4>;
 				status = "disabled";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sam9x60.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sam9x60.dtsi
@@ -567,7 +567,7 @@
 			mpddrc: mpddrc@ffffe800 {
 				compatible = "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
 				reg = <0xffffe800 0x200>;
-				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 49>;
 				clock-names = "ddrck", "mpddr";
 			};
 
@@ -692,7 +692,7 @@
 				compatible = "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
 				reg = <0xfffffe20 0x20>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				clocks = <&clk32k 0>;
+				clocks = <&clk32k 1>;
 			};
 
 			pit: timer@fffffe40 {
@@ -718,7 +718,7 @@
 				compatible = "microchip,sam9x60-rtc", "atmel,at91sam9x5-rtc";
 				reg = <0xfffffea8 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				clocks = <&clk32k 0>;
+				clocks = <&clk32k 1>;
 			};
 
 			watchdog: watchdog@ffffff80 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sama5d2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sama5d2.dtsi
@@ -413,7 +413,7 @@
 				pmecc: ecc-engine@f8014070 {
 					compatible = "atmel,sama5d2-pmecc";
 					reg = <0xf8014070 0x490>,
-					      <0xf8014500 0x100>;
+					      <0xf8014500 0x200>;
 				};
 			};
 
@@ -1125,7 +1125,7 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 55>, <&pmc PMC_TYPE_GCK 55>;
 				clock-names = "pclk", "gclk";
 				assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S1_MUX>;
-				assigned-parrents = <&pmc PMC_TYPE_GCK 55>;
+				assigned-clock-parents = <&pmc PMC_TYPE_GCK 55>;
 				status = "disabled";
 			};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sama7g5-pinfunc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sama7g5-pinfunc.h
@@ -261,7 +261,7 @@
 #define PIN_PB2__FLEXCOM6_IO0		PINMUX_PIN(PIN_PB2, 2, 1)
 #define PIN_PB2__ADTRG			PINMUX_PIN(PIN_PB2, 3, 1)
 #define PIN_PB2__A20			PINMUX_PIN(PIN_PB2, 4, 1)
-#define PIN_PB2__FLEXCOM11_IO0		PINMUX_PIN(PIN_PB2, 6, 3)
+#define PIN_PB2__FLEXCOM11_IO1		PINMUX_PIN(PIN_PB2, 6, 3)
 #define PIN_PB3				35
 #define PIN_PB3__GPIO			PINMUX_PIN(PIN_PB3, 0, 0)
 #define PIN_PB3__RF1			PINMUX_PIN(PIN_PB3, 1, 1)
@@ -765,7 +765,7 @@
 #define PIN_PD20__PCK0			PINMUX_PIN(PIN_PD20, 1, 3)
 #define PIN_PD20__FLEXCOM2_IO3		PINMUX_PIN(PIN_PD20, 2, 2)
 #define PIN_PD20__PWMH3			PINMUX_PIN(PIN_PD20, 3, 4)
-#define PIN_PD20__CANTX4		PINMUX_PIN(PIN_PD20, 5, 2)
+#define PIN_PD20__CANTX4		PINMUX_PIN(PIN_PD20, 4, 2)
 #define PIN_PD20__FLEXCOM5_IO0		PINMUX_PIN(PIN_PD20, 6, 5)
 #define PIN_PD21			117
 #define PIN_PD21__GPIO			PINMUX_PIN(PIN_PD21, 0, 0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sama7g5.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sama7g5.dtsi
@@ -319,8 +319,6 @@
 				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
 					<&dma0 AT91_XDMAC_DT_PERID(8)>;
 				dma-names = "rx", "tx";
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				status = "disabled";
 			};
 		};
@@ -485,8 +483,6 @@
 				dmas = <&dma0 AT91_XDMAC_DT_PERID(21)>,
 					<&dma0 AT91_XDMAC_DT_PERID(22)>;
 				dma-names = "rx", "tx";
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				status = "disabled";
 			};
 		};
@@ -511,8 +507,6 @@
 				dmas = <&dma0 AT91_XDMAC_DT_PERID(23)>,
 					<&dma0 AT91_XDMAC_DT_PERID(24)>;
 				dma-names = "rx", "tx";
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				status = "disabled";
 			};
 		};
@@ -559,7 +553,6 @@
 			#interrupt-cells = <3>;
 			#address-cells = <0>;
 			interrupt-controller;
-			interrupt-parent;
 			reg = <0xe8c11000 0x1000>,
 				<0xe8c12000 0x2000>;
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga.dtsi
@@ -46,7 +46,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@fffed000 {
+	intc: interrupt-controller@fffed000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -782,7 +782,7 @@
 		};
 
 		qspi: spi@ff705000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff705000 0x1000>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_arria10.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_arria10.dtsi
@@ -38,7 +38,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@ffffd000 {
+	intc: interrupt-controller@ffffd000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -756,7 +756,7 @@
 		};
 
 		qspi: spi@ff809000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff809000 0x100>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
@@ -12,7 +12,7 @@
 	flash0: n25q00@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00aa";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_arria5_socdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_arria5_socdk.dts
@@ -119,7 +119,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
@@ -124,7 +124,7 @@
 	flash0: n25q00@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;	/* chip select */
 		spi-max-frequency = <100000000>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
@@ -169,7 +169,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
@@ -80,7 +80,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
@@ -116,7 +116,7 @@
 	flash0: n25q512a@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q512a";
+		compatible = "micron,n25q512a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
@@ -224,7 +224,7 @@
 	n25q128@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q128";
+		compatible = "micron,n25q128", "jedec,spi-nor";
 		reg = <0>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
@@ -241,7 +241,7 @@
 	n25q00@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <1>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/spear1340.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/spear1340.dtsi
@@ -136,9 +136,9 @@
 				reg = <0xb4100000 0x1000>;
 				interrupts = <0 105 0x4>;
 				status = "disabled";
-				dmas = <&dwdma0 12 0 1>,
-					<&dwdma0 13 1 0>;
-				dma-names = "tx", "rx";
+				dmas = <&dwdma0 13 0 1>,
+					<&dwdma0 12 1 0>;
+				dma-names = "rx", "tx";
 			};
 
 			thermal@e07008c4 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/spear13xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/spear13xx.dtsi
@@ -284,9 +284,9 @@
 				#size-cells = <0>;
 				interrupts = <0 31 0x4>;
 				status = "disabled";
-				dmas = <&dwdma0 4 0 0>,
-					<&dwdma0 5 0 0>;
-				dma-names = "tx", "rx";
+				dmas = <&dwdma0 5 0 0>,
+					<&dwdma0 4 0 0>;
+				dma-names = "rx", "tx";
 			};
 
 			rtc@e0580000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/spear320-hmi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/spear320-hmi.dts
@@ -242,7 +242,7 @@
 					irq-trigger = <0x1>;
 
 					stmpegpio: stmpe-gpio {
-						compatible = "stmpe,gpio";
+						compatible = "st,stmpe-gpio";
 						reg = <0>;
 						gpio-controller;
 						#gpio-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/spear600.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/spear600.dtsi
@@ -47,7 +47,7 @@
 			compatible = "arm,pl110", "arm,primecell";
 			reg = <0xfc200000 0x1000>;
 			interrupt-parent = <&vic1>;
-			interrupts = <12>;
+			interrupts = <13>;
 			status = "disabled";
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
@@ -544,8 +544,8 @@
 				reg = <0x19>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
 				vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
-				mount-matrix = "0", "-1", "0",
-					       "1", "0", "0",
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
 					       "0", "0", "1";
 			};
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
@@ -502,8 +502,8 @@
 					accelerometer@18 {
 						compatible = "bosch,bma222e";
 						reg = <0x18>;
-						mount-matrix = "0", "1", "0",
-							       "-1", "0", "0",
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
 							       "0", "0", "1";
 						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
 						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
@@ -181,10 +181,6 @@
 			cap-sd-highspeed;
 			cap-mmc-highspeed;
 			/* All direction control is used */
-			st,sig-dir-cmd;
-			st,sig-dir-dat0;
-			st,sig-dir-dat2;
-			st,sig-dir-dat31;
 			st,sig-pin-fbclk;
 			full-pwr-cycle;
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
@@ -292,10 +288,10 @@
 					};
 
 					ab8500_ldo_aux2 {
-						/* Supplies the Cypress TMA140 touchscreen only with 3.3V */
+						/* Supplies the Cypress TMA140 touchscreen only with 3.0V */
 						regulator-name = "AUX2";
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
 					};
 
 					ab8500_ldo_aux3 {
@@ -314,9 +310,9 @@
 
 					ab8500_ldo_aux5 {
 						regulator-name = "AUX5";
+						/* Intended for 1V8 for touchscreen but actually left unused */
 						regulator-min-microvolt = <1050000>;
 						regulator-max-microvolt = <2790000>;
-						regulator-always-on;
 					};
 
 					ab8500_ldo_aux6 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32f429-disco.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32f429-disco.dts
@@ -192,7 +192,7 @@
 
 	display: display@1{
 		/* Connect panel-ilitek-9341 to ltdc */
-		compatible = "st,sf-tc240t-9370-t";
+		compatible = "st,sf-tc240t-9370-t", "ilitek,ili9341";
 		reg = <1>;
 		spi-3wire;
 		spi-max-frequency = <10000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32f7-pinctrl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32f7-pinctrl.dtsi
@@ -284,6 +284,88 @@
 					slew-rate = <2>;
 				};
 			};
+
+			can1_pins_a: can1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 12, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 11, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can1_pins_b: can1-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 9, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 8, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can1_pins_c: can1-2 {
+				pins1 {
+					pinmux = <STM32_PINMUX('D', 1, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('D', 0, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+
+				};
+			};
+
+			can1_pins_d: can1-3 {
+				pins1 {
+					pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+
+				};
+			};
+
+			can2_pins_a: can2-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 6, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_b: can2-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 12, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can3_pins_a: can3-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 15, AF11)>; /* CAN3_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 8, AF11)>; /* CAN3_RX */
+					bias-pull-up;
+				};
+			};
+
+			can3_pins_b: can3-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 4, AF11)>;  /* CAN3_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 3, AF11)>; /* CAN3_RX */
+					bias-pull-up;
+				};
+			};
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1179,7 +1179,7 @@
 		};
 	};
 
-	sai2a_pins_c: sai2a-4 {
+	sai2a_pins_c: sai2a-2 {
 		pins {
 			pinmux = <STM32_PINMUX('D', 13, AF10)>, /* SAI2_SCK_A */
 				 <STM32_PINMUX('D', 11, AF10)>, /* SAI2_SD_A */
@@ -1190,7 +1190,7 @@
 		};
 	};
 
-	sai2a_sleep_pins_c: sai2a-5 {
+	sai2a_sleep_pins_c: sai2a-sleep-2 {
 		pins {
 			pinmux = <STM32_PINMUX('D', 13, ANALOG)>, /* SAI2_SCK_A */
 				 <STM32_PINMUX('D', 11, ANALOG)>, /* SAI2_SD_A */
@@ -1235,14 +1235,14 @@
 		};
 	};
 
-	sai2b_pins_c: sai2a-4 {
+	sai2b_pins_c: sai2b-2 {
 		pins1 {
 			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
 			bias-disable;
 		};
 	};
 
-	sai2b_sleep_pins_c: sai2a-sleep-5 {
+	sai2b_sleep_pins_c: sai2b-sleep-2 {
 		pins {
 			pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp151.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp151.dtsi
@@ -553,7 +553,7 @@
 			compatible = "st,stm32-cec";
 			reg = <0x40016000 0x400>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CEC_K>, <&clk_lse>;
+			clocks = <&rcc CEC_K>, <&rcc CEC>;
 			clock-names = "cec", "hdmi-cec";
 			status = "disabled";
 		};
@@ -824,7 +824,7 @@
 				#sound-dai-cells = <0>;
 
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x1c>;
+				reg = <0x4 0x20>;
 				clocks = <&rcc SAI1_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 87 0x400 0x01>;
@@ -834,7 +834,7 @@
 			sai1b: audio-controller@4400a024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI1_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 88 0x400 0x01>;
@@ -855,7 +855,7 @@
 			sai2a: audio-controller@4400b004 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x1c>;
+				reg = <0x4 0x20>;
 				clocks = <&rcc SAI2_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 89 0x400 0x01>;
@@ -865,7 +865,7 @@
 			sai2b: audio-controller@4400b024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI2_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 90 0x400 0x01>;
@@ -886,7 +886,7 @@
 			sai3a: audio-controller@4400c004 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x1c>;
+				reg = <0x04 0x20>;
 				clocks = <&rcc SAI3_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 113 0x400 0x01>;
@@ -896,7 +896,7 @@
 			sai3b: audio-controller@4400c024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI3_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 114 0x400 0x01>;
@@ -1271,7 +1271,7 @@
 			sai4a: audio-controller@50027004 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x1c>;
+				reg = <0x04 0x20>;
 				clocks = <&rcc SAI4_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 99 0x400 0x01>;
@@ -1281,7 +1281,7 @@
 			sai4b: audio-controller@50027024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI4_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 100 0x400 0x01>;
@@ -1452,7 +1452,7 @@
 		usbh_ohci: usb@5800c000 {
 			compatible = "generic-ohci";
 			reg = <0x5800c000 0x1000>;
-			clocks = <&rcc USBH>;
+			clocks = <&usbphyc>, <&rcc USBH>;
 			resets = <&rcc USBH_R>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -1461,7 +1461,7 @@
 		usbh_ehci: usb@5800d000 {
 			compatible = "generic-ehci";
 			reg = <0x5800d000 0x1000>;
-			clocks = <&rcc USBH>;
+			clocks = <&usbphyc>, <&rcc USBH>;
 			resets = <&rcc USBH_R>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			companion = <&usbh_ohci>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts
@@ -13,7 +13,6 @@
 /dts-v1/;
 
 #include "stm32mp157.dtsi"
-#include "stm32mp15xc.dtsi"
 #include "stm32mp15xx-dhcor-som.dtsi"
 #include "stm32mp15xx-dhcor-avenger96.dtsi"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -137,10 +137,13 @@
 
 	sound {
 		compatible = "audio-graph-card";
-		routing =
-			"MIC_IN", "Capture",
-			"Capture", "Mic Bias",
-			"Playback", "HP_OUT";
+		widgets = "Headphone", "Headphone Jack",
+			  "Line", "Line In Jack",
+			  "Microphone", "Microphone Jack";
+		routing = "Headphone Jack", "HP_OUT",
+			  "LINE_IN", "Line In Jack",
+			  "MIC_IN", "Microphone Jack",
+			  "Microphone Jack", "Mic Bias";
 		dais = <&sai2a_port &sai2b_port>;
 		status = "okay";
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
@@ -88,7 +88,7 @@
 
 	sound {
 		compatible = "audio-graph-card";
-		label = "STM32MP1-AV96-HDMI";
+		label = "STM32-AV96-HDMI";
 		dais = <&sai2a_port>;
 		status = "okay";
 	};
@@ -100,7 +100,7 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
-		gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpioz 3 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
 };
@@ -141,6 +141,7 @@
 		compatible = "snps,dwmac-mdio";
 		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
 		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
 
 		phy0: ethernet-phy@7 {
 			reg = <7>;
@@ -266,6 +267,12 @@
 			};
 		};
 	};
+
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
 };
 
 &ltdc {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -171,12 +171,6 @@
 			status = "disabled";
 		};
 	};
-
-	eeprom@53 {
-		compatible = "atmel,24c02";
-		reg = <0x53>;
-		pagesize = <16>;
-	};
 };
 
 &iwdg2 {
@@ -202,7 +196,7 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
-		spi-max-frequency = <108000000>;
+		spi-max-frequency = <50000000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
@@ -249,7 +249,7 @@
 	stusb1600@28 {
 		compatible = "st,stusb1600";
 		reg = <0x28>;
-		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-parent = <&gpioi>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&stusb1600_pins_a>;
@@ -438,7 +438,7 @@
 	i2s2_port: port {
 		i2s2_endpoint: endpoint {
 			remote-endpoint = <&sii9022_tx_endpoint>;
-			format = "i2s";
+			dai-format = "i2s";
 			mclk-fs = <256>;
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun8i-a33.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun8i-a33.dtsi
@@ -46,7 +46,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -164,7 +164,7 @@
 		io-channels = <&ths>;
 	};
 
-	mali_opp_table: gpu-opp-table {
+	mali_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-144000000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -200,7 +200,7 @@
 		status = "disabled";
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cluster0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -253,7 +253,7 @@
 		};
 	};
 
-	cpu1_opp_table: opp_table1 {
+	cpu1_opp_table: opp-table-cluster1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -169,7 +169,7 @@
 	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
@@ -57,7 +57,7 @@
 		regulator-ramp-delay = <50>; /* 4ms */
 
 		enable-active-high;
-		enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
 		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
 		gpios-states = <0x1>;
 		states = <1100000 0>, <1300000 1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun8i-h3.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -44,7 +44,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -112,7 +112,7 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-120000000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -593,6 +593,17 @@
 			#size-cells = <0>;
 		};
 
+		gic: interrupt-controller@1c81000 {
+			compatible = "arm,gic-400";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x2000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
 		csi1: camera@1cb4000 {
 			compatible = "allwinner,sun8i-v3s-csi";
 			reg = <0x01cb4000 0x3000>;
@@ -604,16 +615,5 @@
 			resets = <&ccu RST_BUS_CSI>;
 			status = "disabled";
 		};
-
-		gic: interrupt-controller@1c81000 {
-			compatible = "arm,gic-400";
-			reg = <0x01c81000 0x1000>,
-			      <0x01c82000 0x2000>,
-			      <0x01c84000 0x2000>,
-			      <0x01c86000 0x2000>;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
-		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -280,8 +280,8 @@
 
 			reg_dcdc5: dcdc5 {
 				regulator-always-on;
-				regulator-min-microvolt = <1425000>;
-				regulator-max-microvolt = <1575000>;
+				regulator-min-microvolt = <1450000>;
+				regulator-max-microvolt = <1550000>;
 				regulator-name = "vcc-dram";
 			};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/suniv-f1c100s.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/suniv-f1c100s.dtsi
@@ -104,8 +104,10 @@
 
 		wdt: watchdog@1c20ca0 {
 			compatible = "allwinner,suniv-f1c100s-wdt",
-				     "allwinner,sun4i-a10-wdt";
+				     "allwinner,sun6i-a31-wdt";
 			reg = <0x01c20ca0 0x20>;
+			interrupts = <16>;
+			clocks = <&osc32k>;
 		};
 
 		uart0: serial@1c25000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/tegra124-nyan-big.dts
@@ -13,12 +13,15 @@
 		     "google,nyan-big-rev1", "google,nyan-big-rev0",
 		     "google,nyan-big", "google,nyan", "nvidia,tegra124";
 
-	panel: panel {
-		compatible = "auo,b133xtn01";
-
-		power-supply = <&vdd_3v3_panel>;
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "auo,b133xtn01";
+					backlight = <&backlight>;
+				};
+			};
+		};
 	};
 
 	mmc@700b0400 { /* SD Card on this bus */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/tegra124-nyan-blaze.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/tegra124-nyan-blaze.dts
@@ -15,12 +15,15 @@
 		     "google,nyan-blaze-rev0", "google,nyan-blaze",
 		     "google,nyan", "nvidia,tegra124";
 
-	panel: panel {
-		compatible = "samsung,ltn140at29-301";
-
-		power-supply = <&vdd_3v3_panel>;
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "samsung,ltn140at29-301";
+					backlight = <&backlight>;
+				};
+			};
+		};
 	};
 
 	sound {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/tegra124-venice2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/tegra124-venice2.dts
@@ -48,6 +48,13 @@
 		dpaux@545c0000 {
 			vdd-supply = <&vdd_3v3_panel>;
 			status = "okay";
+
+			aux-bus {
+				panel: panel {
+					compatible = "lg,lp129qe";
+					backlight = <&backlight>;
+				};
+			};
 		};
 	};
 
@@ -1079,13 +1086,6 @@
 		};
 	};
 
-	panel: panel {
-		compatible = "lg,lp129qe";
-		power-supply = <&vdd_3v3_panel>;
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
-	};
-
 	vdd_mux: regulator@0 {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_MUX";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/tegra20-tamonten.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/tegra20-tamonten.dtsi
@@ -183,8 +183,8 @@
 			};
 			conf_ata {
 				nvidia,pins = "ata", "atb", "atc", "atd", "ate",
-					"cdev1", "cdev2", "dap1", "dtb", "gma",
-					"gmb", "gmc", "gmd", "gme", "gpu7",
+					"cdev1", "cdev2", "dap1", "dtb", "dtf",
+					"gma", "gmb", "gmc", "gmd", "gme", "gpu7",
 					"gpv", "i2cp", "irrx", "irtx", "pta",
 					"rm", "slxa", "slxk", "spia", "spib",
 					"uac";
@@ -203,7 +203,7 @@
 			};
 			conf_crtp {
 				nvidia,pins = "crtp", "dap2", "dap3", "dap4",
-					"dtc", "dte", "dtf", "gpu", "sdio1",
+					"dtc", "dte", "gpu", "sdio1",
 					"slxc", "slxd", "spdi", "spdo", "spig",
 					"uda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/uniphier-pxs2.dtsi
@@ -597,8 +597,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <0 134 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -693,8 +693,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <0 137 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
 			clock-names = "ref", "bus_early", "suspend";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/vexpress-v2p-ca5s.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/vexpress-v2p-ca5s.dts
@@ -132,6 +132,7 @@
 		reg = <0x2c0f0000 0x1000>;
 		interrupts = <0 84 4>;
 		cache-level = <2>;
+		cache-unified;
 	};
 
 	pmu {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
@@ -343,7 +343,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
@@ -340,7 +340,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-7000.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-7000.dtsi
@@ -1,6 +1,9 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2011 - 2014 Xilinx
+ * Xilinx Zynq 7000 DTSI
+ * Describes the hardware common to all Zynq 7000-based boards.
+ *
+ *  Copyright (C) 2011 - 2015 Xilinx
  */
 
 / {
@@ -93,6 +96,7 @@
 	};
 
 	amba: axi {
+		u-boot,dm-pre-reloc;
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -188,6 +192,13 @@
 			reg = <0xf8006000 0x1000>;
 		};
 
+		ocmc: ocmc@f800c000 {
+			compatible = "xlnx,zynq-ocmc-1.0";
+			interrupt-parent = <&intc>;
+			interrupts = <0 3 4>;
+			reg = <0xf800c000 0x1000>;
+		};
+
 		uart0: serial@e0000000 {
 			compatible = "xlnx,xuartps", "cdns,uart-r1p8";
 			status = "disabled";
@@ -230,6 +241,18 @@
 			#size-cells = <0>;
 		};
 
+		qspi: spi@e000d000 {
+			clock-names = "ref_clk", "pclk";
+			clocks = <&clkc 10>, <&clkc 43>;
+			compatible = "xlnx,zynq-qspi-1.0";
+			status = "disabled";
+			interrupt-parent = <&intc>;
+			interrupts = <0 19 4>;
+			reg = <0xe000d000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		gem0: ethernet@e000b000 {
 			compatible = "cdns,zynq-gem", "cdns,gem";
 			reg = <0xe000b000 0x1000>;
@@ -263,6 +286,8 @@
 				  0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 18 4>;
 
 			nfc0: nand-controller@0,0 {
 				compatible = "arm,pl353-nand-r2p1";
@@ -271,6 +296,13 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 			};
+			nor0: flash@1,0 {
+				status = "disabled";
+				compatible = "cfi-flash";
+				reg = <1 0 0x2000000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
 		};
 
 		sdhci0: mmc@e0100000 {
@@ -294,15 +326,17 @@
 		};
 
 		slcr: slcr@f8000000 {
+			u-boot,dm-pre-reloc;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "xlnx,zynq-slcr", "syscon", "simple-mfd";
 			reg = <0xF8000000 0x1000>;
 			ranges;
 			clkc: clkc@100 {
+				u-boot,dm-pre-reloc;
 				#clock-cells = <1>;
 				compatible = "xlnx,ps7-clkc";
-				fclk-enable = <0>;
+				fclk-enable = <0xf>;
 				clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
 						"cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
 						"dci", "lqspi", "smc", "pcap", "gem0", "gem1",
@@ -351,14 +385,19 @@
 
 		devcfg: devcfg@f8007000 {
 			compatible = "xlnx,zynq-devcfg-1.0";
-			reg = <0xf8007000 0x100>;
 			interrupt-parent = <&intc>;
 			interrupts = <0 8 4>;
-			clocks = <&clkc 12>;
-			clock-names = "ref_clk";
+			reg = <0xf8007000 0x100>;
+			clocks = <&clkc 12>, <&clkc 15>, <&clkc 16>, <&clkc 17>, <&clkc 18>;
+			clock-names = "ref_clk", "fclk0", "fclk1", "fclk2", "fclk3";
 			syscon = <&slcr>;
 		};
 
+		efuse: efuse@f800d000 {
+			compatible = "xlnx,zynq-efuse";
+			reg = <0xf800d000 0x20>;
+		};
+
 		global_timer: timer@f8f00200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0xf8f00200 0x20>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-cc108.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-cc108.dts
@@ -18,6 +18,7 @@
 	aliases {
 		ethernet0 = &gem0;
 		serial0 = &uart0;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -52,6 +53,45 @@
 	};
 };
 
+&qspi {
+	status = "okay";
+	is-dual = <0>;
+	num-cs = <1>;
+	flash@0 { /* 16 MB */
+		compatible = "n25q128a11", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "qspi-fsbl-uboot-bs";
+			reg = <0x0 0x400000>; /* 4MB */
+		};
+		partition@400000 {
+			label = "qspi-linux";
+			reg = <0x400000 0x400000>; /* 4MB */
+		};
+		partition@800000 {
+			label = "qspi-rootfs";
+			reg = <0x800000 0x400000>; /* 4MB */
+		};
+		partition@c00000 {
+			label = "qspi-devicetree";
+			reg = <0xc00000 0x100000>; /* 1MB */
+		};
+		partition@d00000 {
+			label = "qspi-scratch";
+			reg = <0xd00000 0x200000>; /* 2MB */
+		};
+		partition@f00000 {
+			label = "qspi-uboot-env";
+			reg = <0xf00000 0x100000>; /* 1MB */
+		};
+	};
+};
+
 &sdhci1 {
 	status = "okay";
 	broken-cd ;
@@ -59,6 +99,7 @@
 };
 
 &uart0 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zc702.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zc702.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0+
 /*
- *  Copyright (C) 2011 - 2014 Xilinx
+ *  Copyright (C) 2011 - 2015 Xilinx
  *  Copyright (C) 2012 National Instruments Corp.
  */
 /dts-v1/;
@@ -14,7 +14,9 @@
 		ethernet0 = &gem0;
 		i2c0 = &i2c0;
 		serial0 = &uart1;
+		spi0 = &qspi;
 		mmc0 = &sdhci0;
+		usb0 = &usb0;
 	};
 
 	memory@0 {
@@ -56,9 +58,12 @@
 		};
 	};
 
-	usb_phy0: phy0 {
-		compatible = "usb-nop-xceiv";
+	usb_phy0: phy0@e0002000 {
+		compatible = "ulpi-phy";
 		#phy-cells = <0>;
+		reg = <0xe0002000 0x1000>;
+		view-port = <0x0170>;
+		drv-vbus;
 	};
 };
 
@@ -91,6 +96,8 @@
 	phy-handle = <&ethernet_phy>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gem0_default>;
+	phy-reset-gpio = <&gpio0 11 0>;
+	phy-reset-active-low;
 
 	ethernet_phy: ethernet-phy@7 {
 		reg = <7>;
@@ -106,8 +113,11 @@
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio0 50 0>;
+	sda-gpios = <&gpio0 51 0>;
 
 	i2c-mux@74 {
 		compatible = "nxp,pca9548";
@@ -206,7 +216,7 @@
 		conf {
 			groups = "can0_9_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-rx {
@@ -229,7 +239,7 @@
 		conf {
 			groups = "ethernet0_0_grp";
 			slew-rate = <0>;
-			io-standard = <4>;
+			power-source = <4>;
 		};
 
 		conf-rx {
@@ -252,7 +262,7 @@
 		conf-mdio {
 			groups = "mdio0_0_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 			bias-disable;
 		};
 	};
@@ -270,7 +280,7 @@
 				 "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
 				 "gpio0_13_grp", "gpio0_14_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-pull-up {
@@ -294,7 +304,20 @@
 			groups = "i2c0_10_grp";
 			bias-pull-up;
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_50_grp", "gpio0_51_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_50_grp", "gpio0_51_grp";
+			slew-rate = <0>;
+			power-source = <1>;
 		};
 	};
 
@@ -307,7 +330,7 @@
 		conf {
 			groups = "sdio0_2_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 			bias-disable;
 		};
 
@@ -321,7 +344,7 @@
 			bias-high-impedance;
 			bias-pull-up;
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		mux-wp {
@@ -334,7 +357,7 @@
 			bias-high-impedance;
 			bias-pull-up;
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 	};
 
@@ -347,7 +370,7 @@
 		conf {
 			groups = "uart1_10_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-rx {
@@ -370,7 +393,7 @@
 		conf {
 			groups = "usb0_0_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-rx {
@@ -386,13 +409,51 @@
 	};
 };
 
+&qspi {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+	is-dual = <0>;
+	num-cs = <1>;
+	flash@0 {
+		compatible = "n25q128a11", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 {
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 {
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 {
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+		partition@c00000 {
+			label = "qspi-bitstream";
+			reg = <0xC00000 0x400000>;
+		};
+	};
+};
+
 &sdhci0 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sdhci0_default>;
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_default>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zc706.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zc706.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0+
 /*
- *  Copyright (C) 2011 - 2014 Xilinx
+ *  Copyright (C) 2011 - 2015 Xilinx
  *  Copyright (C) 2012 National Instruments Corp.
  */
 /dts-v1/;
@@ -14,6 +14,7 @@
 		ethernet0 = &gem0;
 		i2c0 = &i2c0;
 		serial0 = &uart1;
+		spi0 = &qspi;
 		mmc0 = &sdhci0;
 	};
 
@@ -27,9 +28,12 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	usb_phy0: phy0 {
-		compatible = "usb-nop-xceiv";
+	usb_phy0: phy0@e0002000 {
+		compatible = "ulpi-phy";
 		#phy-cells = <0>;
+		reg = <0xe0002000 0x1000>;
+		view-port = <0x0170>;
+		drv-vbus;
 	};
 };
 
@@ -150,7 +154,7 @@
 		conf {
 			groups = "ethernet0_0_grp";
 			slew-rate = <0>;
-			io-standard = <4>;
+			power-source = <4>;
 		};
 
 		conf-rx {
@@ -173,7 +177,7 @@
 		conf-mdio {
 			groups = "mdio0_0_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 			bias-disable;
 		};
 	};
@@ -187,7 +191,7 @@
 		conf {
 			groups = "gpio0_7_grp", "gpio0_46_grp", "gpio0_47_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-pull-up {
@@ -211,7 +215,7 @@
 			groups = "i2c0_10_grp";
 			bias-pull-up;
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 	};
 
@@ -224,7 +228,7 @@
 		conf {
 			groups = "sdio0_2_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 			bias-disable;
 		};
 
@@ -238,7 +242,7 @@
 			bias-high-impedance;
 			bias-pull-up;
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		mux-wp {
@@ -251,7 +255,7 @@
 			bias-high-impedance;
 			bias-pull-up;
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 	};
 
@@ -264,7 +268,7 @@
 		conf {
 			groups = "uart1_10_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-rx {
@@ -287,7 +291,7 @@
 		conf {
 			groups = "usb0_0_grp";
 			slew-rate = <0>;
-			io-standard = <1>;
+			power-source = <1>;
 		};
 
 		conf-rx {
@@ -303,13 +307,51 @@
 	};
 };
 
+&qspi {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+	is-dual = <1>;
+	num-cs = <1>;
+	flash@0 {
+		compatible = "n25q128a11", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 {
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 {
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 {
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+		partition@c00000 {
+			label = "qspi-bitstream";
+			reg = <0xC00000 0x400000>;
+		};
+	};
+};
+
 &sdhci0 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sdhci0_default>;
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_default>;
@@ -322,3 +364,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usb0_default>;
 };
+
+&watchdog0 {
+	reset-on-timeout;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zc770-xm010.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zc770-xm010.dts
@@ -15,6 +15,7 @@
 		ethernet0 = &gem0;
 		i2c0 = &i2c0;
 		serial0 = &uart1;
+		spi0 = &qspi;
 		spi1 = &spi1;
 	};
 
@@ -57,7 +58,41 @@
 		compatible = "atmel,24c02";
 		reg = <0x52>;
 	};
+};
 
+&qspi {
+	status = "okay";
+	is-dual = <0>;
+	num-cs = <1>;
+	flash@0 {
+		compatible = "n25q128a11", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 {
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 {
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 {
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+		partition@c00000 {
+			label = "qspi-bitstream";
+			reg = <0xC00000 0x400000>;
+		};
+	};
 };
 
 &sdhci0 {
@@ -85,6 +120,7 @@
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zc770-xm011.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zc770-xm011.dts
@@ -47,6 +47,33 @@
 	};
 };
 
+&nfc0 {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "nand-fsbl-uboot";
+			reg = <0x0 0x1000000>;
+		};
+		partition@1000000 {
+			label = "nand-linux";
+			reg = <0x1000000 0x2000000>;
+		};
+		partition@3000000 {
+			label = "nand-rootfs";
+			reg = <0x3000000 0x200000>;
+		};
+	};
+};
+
+&smcc {
+	status = "okay";
+};
+
 &spi0 {
 	status = "okay";
 	num-cs = <4>;
@@ -54,6 +81,7 @@
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zc770-xm012.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zc770-xm012.dts
@@ -53,6 +53,35 @@
 	};
 };
 
+&nor0 {
+	status = "okay";
+	bank-width = <1>;
+	partition@0 {
+		label = "nor-fsbl-uboot";
+		reg = <0x0 0x100000>;
+	};
+	partition@100000 {
+		label = "nor-linux";
+		reg = <0x100000 0x500000>;
+	};
+	partition@600000 {
+		label = "nor-device-tree";
+		reg = <0x600000 0x20000>;
+	};
+	partition@620000 {
+		label = "nor-rootfs";
+		reg = <0x620000 0x5E0000>;
+	};
+	partition@c00000 {
+		label = "nor-bitstream";
+		reg = <0xC00000 0x400000>;
+	};
+};
+
+&smcc {
+	status = "okay";
+};
+
 &spi1 {
 	status = "okay";
 	num-cs = <4>;
@@ -60,5 +89,6 @@
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zc770-xm013.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zc770-xm013.dts
@@ -15,6 +15,7 @@
 		ethernet0 = &gem1;
 		i2c0 = &i2c1;
 		serial0 = &uart0;
+		spi0 = &qspi;
 		spi1 = &spi0;
 	};
 
@@ -58,6 +59,41 @@
 	};
 };
 
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	num-cs = <1>;
+	flash@0 {
+		compatible = "n25q128a11", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 {
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 {
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 {
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+		partition@c00000 {
+			label = "qspi-bitstream";
+			reg = <0xC00000 0x400000>;
+		};
+	};
+};
+
 &spi0 {
 	status = "okay";
 	num-cs = <4>;
@@ -73,5 +109,6 @@
 };
 
 &uart0 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zed.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zed.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0+
 /*
- *  Copyright (C) 2011 - 2014 Xilinx
+ *  Copyright (C) 2011 - 2015 Xilinx
  *  Copyright (C) 2012 National Instruments Corp.
  */
 /dts-v1/;
@@ -13,6 +13,7 @@
 	aliases {
 		ethernet0 = &gem0;
 		serial0 = &uart1;
+		spi0 = &qspi;
 		mmc0 = &sdhci0;
 	};
 
@@ -26,9 +27,12 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	usb_phy0: phy0 {
-		compatible = "usb-nop-xceiv";
+	usb_phy0: phy0@e0002000 {
+		compatible = "ulpi-phy";
 		#phy-cells = <0>;
+		reg = <0xe0002000 0x1000>;
+		view-port = <0x0170>;
+		drv-vbus;
 	};
 };
 
@@ -47,11 +51,50 @@
 	};
 };
 
+&qspi {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+	is-dual = <0>;
+	num-cs = <1>;
+	flash@0 {
+		compatible = "spansion,s25fl256s1", "jedec,spi-nor";
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 {
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 {
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 {
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+		partition@c00000 {
+			label = "qspi-bitstream";
+			reg = <0xC00000 0x400000>;
+		};
+	};
+};
+
 &sdhci0 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/boot/dts/zynq-zybo.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/boot/dts/zynq-zybo.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0+
 /*
- *  Copyright (C) 2011 - 2014 Xilinx
+ *  Copyright (C) 2011 - 2015 Xilinx
  *  Copyright (C) 2012 National Instruments Corp.
  */
 /dts-v1/;
@@ -13,6 +13,7 @@
 	aliases {
 		ethernet0 = &gem0;
 		serial0 = &uart1;
+		spi0 = &qspi;
 		mmc0 = &sdhci0;
 	};
 
@@ -48,11 +49,18 @@
 	};
 };
 
+&qspi {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+};
+
 &sdhci0 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
 &uart1 {
+	u-boot,dm-pre-reloc;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/bcm2835_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/bcm2835_defconfig
@@ -108,6 +108,7 @@
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_DRM=y
 CONFIG_DRM_VC4=y
+CONFIG_FB=y
 CONFIG_FB_SIMPLE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_SOUND=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/cm_x300_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/cm_x300_defconfig
@@ -146,7 +146,6 @@
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_ISO8859_1=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/ezx_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/ezx_defconfig
@@ -314,7 +314,6 @@
 CONFIG_SMB_FS=m
 CONFIG_CIFS=m
 CONFIG_CIFS_STATS=y
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/imote2_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/imote2_defconfig
@@ -288,7 +288,6 @@
 CONFIG_SMB_FS=m
 CONFIG_CIFS=m
 CONFIG_CIFS_STATS=y
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/multi_v5_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/multi_v5_defconfig
@@ -188,6 +188,7 @@
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_PLATFORM_SUPPORT=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_ASPEED=m
 CONFIG_VIDEO_ATMEL_ISI=m
@@ -195,6 +196,7 @@
 CONFIG_DRM_ATMEL_HLCDC=m
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_ASPEED_GFX=m
+CONFIG_FB=y
 CONFIG_FB_IMX=y
 CONFIG_FB_ATMEL=y
 CONFIG_BACKLIGHT_ATMEL_LCDC=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/multi_v7_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/multi_v7_defconfig
@@ -696,7 +696,6 @@
 CONFIG_DRM_IMX_HDMI=m
 CONFIG_DRM_ATMEL_HLCDC=m
 CONFIG_DRM_RCAR_DU=m
-CONFIG_DRM_RCAR_LVDS=y
 CONFIG_DRM_SUN4I=m
 CONFIG_DRM_MSM=m
 CONFIG_DRM_FSL_DCU=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/mxs_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/mxs_defconfig
@@ -93,6 +93,7 @@
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
 CONFIG_DRM_MXSFB=y
+CONFIG_FB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/nhk8815_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/nhk8815_defconfig
@@ -127,7 +127,6 @@
 CONFIG_NFS_V3_ACL=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/pxa_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/pxa_defconfig
@@ -699,7 +699,6 @@
 CONFIG_NFSD_V4=y
 CONFIG_CIFS=m
 CONFIG_CIFS_STATS=y
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_DEFAULT="utf8"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/spear13xx_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/spear13xx_defconfig
@@ -61,7 +61,6 @@
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=8192
 CONFIG_I2C=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/spear3xx_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/spear3xx_defconfig
@@ -41,7 +41,6 @@
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=8192
 CONFIG_I2C=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/spear6xx_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/spear6xx_defconfig
@@ -36,7 +36,6 @@
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=8192
 CONFIG_I2C=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/configs/xilinx_zynq_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/configs/xilinx_zynq_defconfig
@@ -0,0 +1,232 @@
+CONFIG_LOCALVERSION="-xilinx"
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+# CONFIG_BUG is not set
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+CONFIG_SLAB=y
+CONFIG_ARCH_VEXPRESS=y
+CONFIG_ARCH_ZYNQ=y
+CONFIG_PL310_ERRATA_588369=y
+CONFIG_PL310_ERRATA_727915=y
+CONFIG_PL310_ERRATA_769419=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_754327=y
+CONFIG_ARM_ERRATA_764369=y
+CONFIG_ARM_ERRATA_775420=y
+CONFIG_SMP=y
+CONFIG_SCHED_MC=y
+CONFIG_SCHED_SMT=y
+CONFIG_BIG_LITTLE=y
+CONFIG_BL_SWITCHER=y
+CONFIG_HIGHMEM=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_IDLE=y
+CONFIG_ARM_ZYNQ_CPUIDLE=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+# CONFIG_GCC_PLUGINS is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPIP=m
+CONFIG_SYN_COOKIES=y
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_CAN=y
+CONFIG_CAN_XILINXCAN=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCIE_XILINX=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_CONNECTOR=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_PL35X=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_OF_OVERLAY=y
+CONFIG_OF_CONFIGFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_XILINX_TRAFGEN=y
+CONFIG_EEPROM_AT24=y
+CONFIG_EEPROM_AT25=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NETDEVICES=y
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+CONFIG_E1000E=y
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+CONFIG_R8169=y
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_XILINX_EMACLITE=y
+CONFIG_XILINX_AXI_EMAC=y
+CONFIG_MARVELL_PHY=y
+CONFIG_VITESSE_PHY=y
+CONFIG_MDIO_BITBANG=y
+CONFIG_INPUT_SPARSEKMAP=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_GPIO_POLLED=y
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_CADENCE=y
+CONFIG_SPI=y
+CONFIG_SPI_CADENCE=y
+CONFIG_SPI_XILINX=y
+CONFIG_SPI_ZYNQ_QSPI=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+CONFIG_GPIO_ZYNQ=y
+CONFIG_PMBUS=y
+CONFIG_SENSORS_UCD9000=y
+CONFIG_SENSORS_UCD9200=y
+CONFIG_THERMAL=y
+CONFIG_CPU_THERMAL=y
+CONFIG_WATCHDOG=y
+CONFIG_XILINX_WATCHDOG=y
+CONFIG_CADENCE_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_XILINX=y
+CONFIG_VIDEO_XILINX_CFA=y
+CONFIG_VIDEO_XILINX_CRESAMPLE=y
+CONFIG_VIDEO_XILINX_REMAPPER=y
+CONFIG_VIDEO_XILINX_RGB2YUV=y
+CONFIG_VIDEO_XILINX_SCALER=y
+CONFIG_VIDEO_XILINX_SWITCH=y
+CONFIG_VIDEO_XILINX_TPG=y
+CONFIG_VIDEO_ADV7604=y
+CONFIG_DRM=y
+CONFIG_DRM_XLNX=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_ADI=y
+CONFIG_SND_SOC_ADI_AXI_I2S=y
+CONFIG_SND_SOC_ADI_AXI_SPDIF=y
+CONFIG_HID_MICROSOFT=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_STORAGE=y
+CONFIG_USB_CHIPIDEA=y
+CONFIG_USB_CHIPIDEA_UDC=y
+CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_NOP_USB_XCEIV=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_XILINX=y
+CONFIG_USB_CONFIGFS=m
+CONFIG_USB_CONFIGFS_MASS_STORAGE=y
+CONFIG_USB_ZERO=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ARASAN=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_LEDS_TRIGGER_TRANSIENT=y
+CONFIG_LEDS_TRIGGER_CAMERA=y
+CONFIG_EDAC=y
+CONFIG_EDAC_SYNOPSYS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_PCF8563=y
+CONFIG_DMADEVICES=y
+CONFIG_PL330_DMA=y
+CONFIG_XILINX_DMA=y
+CONFIG_UIO=y
+CONFIG_UIO_PDRV_GENIRQ=y
+CONFIG_UIO_XILINX_APM=y
+CONFIG_COMMON_CLK_SI570=y
+CONFIG_REMOTEPROC=y
+CONFIG_ZYNQ_REMOTEPROC=m
+CONFIG_MEMORY=y
+CONFIG_IIO=y
+CONFIG_XILINX_XADC=y
+CONFIG_XILINX_INTC=y
+CONFIG_RAS=y
+CONFIG_FPGA=y
+CONFIG_FPGA_MGR_ZYNQ_FPGA=y
+CONFIG_FPGA_MGR_ZYNQ_AFI_FPGA=y
+CONFIG_XILINX_PR_DECOUPLER=y
+CONFIG_FPGA_REGION=y
+CONFIG_OF_FPGA_REGION=y
+CONFIG_EXT3_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_DMA_CMA=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_RCU_CPU_STALL_TIMEOUT=60
+# CONFIG_FTRACE is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/crypto/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/crypto/Kconfig
@@ -63,7 +63,7 @@
 	  using optimized ARM assembler and NEON, when available.
 
 config CRYPTO_BLAKE2S_ARM
-	tristate "BLAKE2s digest algorithm (ARM)"
+	bool "BLAKE2s digest algorithm (ARM)"
 	select CRYPTO_ARCH_HAVE_LIB_BLAKE2S
 	help
 	  BLAKE2s digest algorithm optimized with ARM scalar instructions.  This
@@ -102,6 +102,8 @@
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
 	select CRYPTO_LIB_AES
+	select CRYPTO_AES
+	select CRYPTO_CBC
 	select CRYPTO_SIMD
 	help
 	  Use a faster and more secure NEON based implementation of AES in CBC,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/crypto/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/crypto/Makefile
@@ -9,7 +9,7 @@
 obj-$(CONFIG_CRYPTO_SHA1_ARM_NEON) += sha1-arm-neon.o
 obj-$(CONFIG_CRYPTO_SHA256_ARM) += sha256-arm.o
 obj-$(CONFIG_CRYPTO_SHA512_ARM) += sha512-arm.o
-obj-$(CONFIG_CRYPTO_BLAKE2S_ARM) += blake2s-arm.o
+obj-$(CONFIG_CRYPTO_BLAKE2S_ARM) += libblake2s-arm.o
 obj-$(CONFIG_CRYPTO_BLAKE2B_NEON) += blake2b-neon.o
 obj-$(CONFIG_CRYPTO_CHACHA20_NEON) += chacha-neon.o
 obj-$(CONFIG_CRYPTO_POLY1305_ARM) += poly1305-arm.o
@@ -31,7 +31,7 @@
 sha256-arm-y	:= sha256-core.o sha256_glue.o $(sha256-arm-neon-y)
 sha512-arm-neon-$(CONFIG_KERNEL_MODE_NEON) := sha512-neon-glue.o
 sha512-arm-y	:= sha512-core.o sha512-glue.o $(sha512-arm-neon-y)
-blake2s-arm-y   := blake2s-core.o blake2s-glue.o
+libblake2s-arm-y:= blake2s-core.o blake2s-glue.o
 blake2b-neon-y  := blake2b-neon-core.o blake2b-neon-glue.o
 sha1-arm-ce-y	:= sha1-ce-core.o sha1-ce-glue.o
 sha2-arm-ce-y	:= sha2-ce-core.o sha2-ce-glue.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/crypto/blake2s-core.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/crypto/blake2s-core.S
@@ -167,8 +167,8 @@
 .endm
 
 //
-// void blake2s_compress_arch(struct blake2s_state *state,
-//			      const u8 *block, size_t nblocks, u32 inc);
+// void blake2s_compress(struct blake2s_state *state,
+//			 const u8 *block, size_t nblocks, u32 inc);
 //
 // Only the first three fields of struct blake2s_state are used:
 //	u32 h[8];	(inout)
@@ -176,7 +176,7 @@
 //	u32 f[2];	(in)
 //
 	.align		5
-ENTRY(blake2s_compress_arch)
+ENTRY(blake2s_compress)
 	push		{r0-r2,r4-r11,lr}	// keep this an even number
 
 .Lnext_block:
@@ -303,4 +303,4 @@
 	str		r3, [r12], #4
 	bne		1b
 	b		.Lcopy_block_done
-ENDPROC(blake2s_compress_arch)
+ENDPROC(blake2s_compress)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/crypto/blake2s-glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/crypto/blake2s-glue.c
@@ -1,78 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * BLAKE2s digest algorithm, ARM scalar implementation
- *
- * Copyright 2020 Google LLC
- */
 
 #include <crypto/internal/blake2s.h>
-#include <crypto/internal/hash.h>
-
 #include <linux/module.h>
 
 /* defined in blake2s-core.S */
-EXPORT_SYMBOL(blake2s_compress_arch);
-
-static int crypto_blake2s_update_arm(struct shash_desc *desc,
-				     const u8 *in, unsigned int inlen)
-{
-	return crypto_blake2s_update(desc, in, inlen, blake2s_compress_arch);
-}
-
-static int crypto_blake2s_final_arm(struct shash_desc *desc, u8 *out)
-{
-	return crypto_blake2s_final(desc, out, blake2s_compress_arch);
-}
-
-#define BLAKE2S_ALG(name, driver_name, digest_size)			\
-	{								\
-		.base.cra_name		= name,				\
-		.base.cra_driver_name	= driver_name,			\
-		.base.cra_priority	= 200,				\
-		.base.cra_flags		= CRYPTO_ALG_OPTIONAL_KEY,	\
-		.base.cra_blocksize	= BLAKE2S_BLOCK_SIZE,		\
-		.base.cra_ctxsize	= sizeof(struct blake2s_tfm_ctx), \
-		.base.cra_module	= THIS_MODULE,			\
-		.digestsize		= digest_size,			\
-		.setkey			= crypto_blake2s_setkey,	\
-		.init			= crypto_blake2s_init,		\
-		.update			= crypto_blake2s_update_arm,	\
-		.final			= crypto_blake2s_final_arm,	\
-		.descsize		= sizeof(struct blake2s_state),	\
-	}
-
-static struct shash_alg blake2s_arm_algs[] = {
-	BLAKE2S_ALG("blake2s-128", "blake2s-128-arm", BLAKE2S_128_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-160", "blake2s-160-arm", BLAKE2S_160_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-224", "blake2s-224-arm", BLAKE2S_224_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-256", "blake2s-256-arm", BLAKE2S_256_HASH_SIZE),
-};
-
-static int __init blake2s_arm_mod_init(void)
-{
-	return IS_REACHABLE(CONFIG_CRYPTO_HASH) ?
-		crypto_register_shashes(blake2s_arm_algs,
-					ARRAY_SIZE(blake2s_arm_algs)) : 0;
-}
-
-static void __exit blake2s_arm_mod_exit(void)
-{
-	if (IS_REACHABLE(CONFIG_CRYPTO_HASH))
-		crypto_unregister_shashes(blake2s_arm_algs,
-					  ARRAY_SIZE(blake2s_arm_algs));
-}
-
-module_init(blake2s_arm_mod_init);
-module_exit(blake2s_arm_mod_exit);
-
-MODULE_DESCRIPTION("BLAKE2s digest algorithm, ARM scalar implementation");
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Eric Biggers <ebiggers@google.com>");
-MODULE_ALIAS_CRYPTO("blake2s-128");
-MODULE_ALIAS_CRYPTO("blake2s-128-arm");
-MODULE_ALIAS_CRYPTO("blake2s-160");
-MODULE_ALIAS_CRYPTO("blake2s-160-arm");
-MODULE_ALIAS_CRYPTO("blake2s-224");
-MODULE_ALIAS_CRYPTO("blake2s-224-arm");
-MODULE_ALIAS_CRYPTO("blake2s-256");
-MODULE_ALIAS_CRYPTO("blake2s-256-arm");
+EXPORT_SYMBOL(blake2s_compress);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/crypto/sha256_glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/crypto/sha256_glue.c
@@ -24,8 +24,8 @@
 
 #include "sha256_glue.h"
 
-asmlinkage void sha256_block_data_order(u32 *digest, const void *data,
-					unsigned int num_blks);
+asmlinkage void sha256_block_data_order(struct sha256_state *state,
+					const u8 *data, int num_blks);
 
 int crypto_sha256_arm_update(struct shash_desc *desc, const u8 *data,
 			     unsigned int len)
@@ -33,23 +33,20 @@
 	/* make sure casting to sha256_block_fn() is safe */
 	BUILD_BUG_ON(offsetof(struct sha256_state, state) != 0);
 
-	return sha256_base_do_update(desc, data, len,
-				(sha256_block_fn *)sha256_block_data_order);
+	return sha256_base_do_update(desc, data, len, sha256_block_data_order);
 }
 EXPORT_SYMBOL(crypto_sha256_arm_update);
 
 static int crypto_sha256_arm_final(struct shash_desc *desc, u8 *out)
 {
-	sha256_base_do_finalize(desc,
-				(sha256_block_fn *)sha256_block_data_order);
+	sha256_base_do_finalize(desc, sha256_block_data_order);
 	return sha256_base_finish(desc, out);
 }
 
 int crypto_sha256_arm_finup(struct shash_desc *desc, const u8 *data,
 			    unsigned int len, u8 *out)
 {
-	sha256_base_do_update(desc, data, len,
-			      (sha256_block_fn *)sha256_block_data_order);
+	sha256_base_do_update(desc, data, len, sha256_block_data_order);
 	return crypto_sha256_arm_final(desc, out);
 }
 EXPORT_SYMBOL(crypto_sha256_arm_finup);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/crypto/sha512-glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/crypto/sha512-glue.c
@@ -25,27 +25,25 @@
 MODULE_ALIAS_CRYPTO("sha384-arm");
 MODULE_ALIAS_CRYPTO("sha512-arm");
 
-asmlinkage void sha512_block_data_order(u64 *state, u8 const *src, int blocks);
+asmlinkage void sha512_block_data_order(struct sha512_state *state,
+					u8 const *src, int blocks);
 
 int sha512_arm_update(struct shash_desc *desc, const u8 *data,
 		      unsigned int len)
 {
-	return sha512_base_do_update(desc, data, len,
-		(sha512_block_fn *)sha512_block_data_order);
+	return sha512_base_do_update(desc, data, len, sha512_block_data_order);
 }
 
 static int sha512_arm_final(struct shash_desc *desc, u8 *out)
 {
-	sha512_base_do_finalize(desc,
-		(sha512_block_fn *)sha512_block_data_order);
+	sha512_base_do_finalize(desc, sha512_block_data_order);
 	return sha512_base_finish(desc, out);
 }
 
 int sha512_arm_finup(struct shash_desc *desc, const u8 *data,
 		     unsigned int len, u8 *out)
 {
-	sha512_base_do_update(desc, data, len,
-		(sha512_block_fn *)sha512_block_data_order);
+	sha512_base_do_update(desc, data, len, sha512_block_data_order);
 	return sha512_arm_final(desc, out);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/arch_gicv3.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/arch_gicv3.h
@@ -48,6 +48,7 @@
 	return read_sysreg(a32); 		\
 }						\
 
+CPUIF_MAP(ICC_EOIR1, ICC_EOIR1_EL1)
 CPUIF_MAP(ICC_PMR, ICC_PMR_EL1)
 CPUIF_MAP(ICC_AP0R0, ICC_AP0R0_EL1)
 CPUIF_MAP(ICC_AP0R1, ICC_AP0R1_EL1)
@@ -63,12 +64,6 @@
 
 /* Low-level accessors */
 
-static inline void gic_write_eoir(u32 irq)
-{
-	write_sysreg(irq, ICC_EOIR1);
-	isb();
-}
-
 static inline void gic_write_dir(u32 val)
 {
 	write_sysreg(val, ICC_DIR);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/arch_timer.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/arch_timer.h
@@ -7,6 +7,7 @@
 #include <asm/hwcap.h>
 #include <linux/clocksource.h>
 #include <linux/init.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
 #include <linux/types.h>
 
 #include <clocksource/arm_arch_timer.h>
@@ -24,29 +25,35 @@
  * the code. At least it does so with a recent GCC (4.6.3).
  */
 static __always_inline
-void arch_timer_reg_write_cp15(int access, enum arch_timer_reg reg, u32 val)
+void arch_timer_reg_write_cp15(int access, enum arch_timer_reg reg, u64 val)
 {
 	if (access == ARCH_TIMER_PHYS_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
-			asm volatile("mcr p15, 0, %0, c14, c2, 1" : : "r" (val));
+			asm volatile("mcr p15, 0, %0, c14, c2, 1" : : "r" ((u32)val));
+			isb();
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			asm volatile("mcr p15, 0, %0, c14, c2, 0" : : "r" (val));
+		case ARCH_TIMER_REG_CVAL:
+			asm volatile("mcrr p15, 2, %Q0, %R0, c14" : : "r" (val));
 			break;
+		default:
+			BUILD_BUG();
 		}
 	} else if (access == ARCH_TIMER_VIRT_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
-			asm volatile("mcr p15, 0, %0, c14, c3, 1" : : "r" (val));
+			asm volatile("mcr p15, 0, %0, c14, c3, 1" : : "r" ((u32)val));
+			isb();
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			asm volatile("mcr p15, 0, %0, c14, c3, 0" : : "r" (val));
+		case ARCH_TIMER_REG_CVAL:
+			asm volatile("mcrr p15, 3, %Q0, %R0, c14" : : "r" (val));
 			break;
+		default:
+			BUILD_BUG();
 		}
+	} else {
+		BUILD_BUG();
 	}
-
-	isb();
 }
 
 static __always_inline
@@ -59,19 +66,19 @@
 		case ARCH_TIMER_REG_CTRL:
 			asm volatile("mrc p15, 0, %0, c14, c2, 1" : "=r" (val));
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			asm volatile("mrc p15, 0, %0, c14, c2, 0" : "=r" (val));
-			break;
+		default:
+			BUILD_BUG();
 		}
 	} else if (access == ARCH_TIMER_VIRT_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
 			asm volatile("mrc p15, 0, %0, c14, c3, 1" : "=r" (val));
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			asm volatile("mrc p15, 0, %0, c14, c3, 0" : "=r" (val));
-			break;
+		default:
+			BUILD_BUG();
 		}
+	} else {
+		BUILD_BUG();
 	}
 
 	return val;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/assembler.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/assembler.h
@@ -107,6 +107,16 @@
 	.endm
 #endif
 
+#if __LINUX_ARM_ARCH__ < 7
+	.macro	dsb, args
+	mcr	p15, 0, r0, c7, c10, 4
+	.endm
+
+	.macro	isb, args
+	mcr	p15, 0, r0, c7, c5, 4
+	.endm
+#endif
+
 	.macro asm_trace_hardirqs_off, save=1
 #if defined(CONFIG_TRACE_IRQFLAGS)
 	.if \save
@@ -259,6 +269,7 @@
  */
 #define ALT_UP(instr...)					\
 	.pushsection ".alt.smp.init", "a"			;\
+	.align	2						;\
 	.long	9998b - .					;\
 9997:	instr							;\
 	.if . - 9997b == 2					;\
@@ -270,6 +281,7 @@
 	.popsection
 #define ALT_UP_B(label)					\
 	.pushsection ".alt.smp.init", "a"			;\
+	.align	2						;\
 	.long	9998b - .					;\
 	W(b)	. + (label - 9998b)					;\
 	.popsection
@@ -314,6 +326,23 @@
 #endif
 	.endm
 
+/*
+ * Raw SMP data memory barrier
+ */
+	.macro	__smp_dmb mode
+#if __LINUX_ARM_ARCH__ >= 7
+	.ifeqs "\mode","arm"
+	dmb	ish
+	.else
+	W(dmb)	ish
+	.endif
+#elif __LINUX_ARM_ARCH__ == 6
+	mcr	p15, 0, r0, c7, c10, 5	@ dmb
+#else
+	.error "Incompatible SMP platform"
+#endif
+	.endm
+
 #if defined(CONFIG_CPU_V7M)
 	/*
 	 * setmode is used to assert to be in svc mode during boot. For v7-M
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/bugs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/bugs.h
@@ -1,7 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- *  arch/arm/include/asm/bugs.h
- *
  *  Copyright (C) 1995-2003 Russell King
  */
 #ifndef __ASM_BUGS_H
@@ -10,10 +8,8 @@
 extern void check_writebuffer_bugs(void);
 
 #ifdef CONFIG_MMU
-extern void check_bugs(void);
 extern void check_other_bugs(void);
 #else
-#define check_bugs() do { } while (0)
 #define check_other_bugs() do { } while (0)
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/dma.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/dma.h
@@ -10,7 +10,7 @@
 #else
 #define MAX_DMA_ADDRESS	({ \
 	extern phys_addr_t arm_dma_zone_size; \
-	arm_dma_zone_size && arm_dma_zone_size < (0x10000000 - PAGE_OFFSET) ? \
+	arm_dma_zone_size && arm_dma_zone_size < (0x100000000ULL - PAGE_OFFSET) ? \
 		(PAGE_OFFSET + arm_dma_zone_size) : 0xffffffffUL; })
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/efi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/efi.h
@@ -17,7 +17,6 @@
 
 #ifdef CONFIG_EFI
 void efi_init(void);
-extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
 
 int efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md);
 int efi_set_mapping_permissions(struct mm_struct *mm, efi_memory_desc_t *md);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/entry-macro-multi.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/entry-macro-multi.S
@@ -13,28 +13,4 @@
 	@
 	badrne	lr, 1b
 	bne	asm_do_IRQ
-
-#ifdef CONFIG_SMP
-	/*
-	 * XXX
-	 *
-	 * this macro assumes that irqstat (r2) and base (r6) are
-	 * preserved from get_irqnr_and_base above
-	 */
-	ALT_SMP(test_for_ipi r0, r2, r6, lr)
-	ALT_UP_B(9997f)
-	movne	r1, sp
-	badrne	lr, 1b
-	bne	do_IPI
-#endif
-9997:
-	.endm
-
-	.macro	arch_irq_handler, symbol_name
-	.align	5
-	.global \symbol_name
-\symbol_name:
-	mov	r8, lr
-	arch_irq_handler_default
-	ret	r8
 	.endm
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/exception.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/exception.h
@@ -10,10 +10,6 @@
 
 #include <linux/interrupt.h>
 
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
 #define __exception_irq_entry	__irq_entry
-#else
-#define __exception_irq_entry
-#endif
 
 #endif /* __ASM_ARM_EXCEPTION_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/hardware/cache-aurora-l2.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/hardware/cache-aurora-l2.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AURORA shared L2 cache controller support
  *
@@ -5,10 +6,6 @@
  *
  * Yehuda Yitschak <yehuday@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARM_HARDWARE_AURORA_L2_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/hardware/cache-feroceon-l2.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/hardware/cache-feroceon-l2.h
@@ -1,13 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/include/asm/hardware/cache-feroceon-l2.h
  *
  * Copyright (C) 2008 Marvell Semiconductor
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 extern void __init feroceon_l2_init(int l2_wt_override);
 extern int __init feroceon_of_init(void);
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/hardware/cache-tauros2.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/hardware/cache-tauros2.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/include/asm/hardware/cache-tauros2.h
  *
  * Copyright (C) 2008 Marvell Semiconductor
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define CACHE_TAUROS2_PREFETCH_ON	(1 << 0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/io.h
@@ -436,6 +436,9 @@
 #define ARCH_HAS_VALID_PHYS_ADDR_RANGE
 extern int valid_phys_addr_range(phys_addr_t addr, size_t size);
 extern int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
+extern bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+					unsigned long flags);
+#define arch_memremap_can_ram_remap arch_memremap_can_ram_remap
 #endif
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/mach/map.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/mach/map.h
@@ -27,6 +27,7 @@
 	MT_HIGH_VECTORS,
 	MT_MEMORY_RWX,
 	MT_MEMORY_RW,
+	MT_MEMORY_RO,
 	MT_ROM,
 	MT_MEMORY_RWX_NONCACHED,
 	MT_MEMORY_RW_DTCM,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/perf_event.h
@@ -17,7 +17,7 @@
 
 #define perf_arch_fetch_caller_regs(regs, __ip) { \
 	(regs)->ARM_pc = (__ip); \
-	(regs)->ARM_fp = (unsigned long) __builtin_frame_address(0); \
+	frame_pointer((regs)) = (unsigned long) __builtin_frame_address(0); \
 	(regs)->ARM_sp = current_stack_pointer; \
 	(regs)->ARM_cpsr = SVC_MODE; \
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/pgtable-nommu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/pgtable-nommu.h
@@ -45,12 +45,6 @@
 typedef pte_t *pte_addr_t;
 
 /*
- * ZERO_PAGE is a global shared page that is always zero: used
- * for zero-mapped memory areas etc..
- */
-#define ZERO_PAGE(vaddr)	(virt_to_page(0))
-
-/*
  * Mark the prot value as uncacheable and unbufferable.
  */
 #define pgprot_noncached(prot)	(prot)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/pgtable.h
@@ -10,6 +10,15 @@
 #include <linux/const.h>
 #include <asm/proc-fns.h>
 
+#ifndef __ASSEMBLY__
+/*
+ * ZERO_PAGE is a global shared page that is always zero: used
+ * for zero-mapped memory areas etc..
+ */
+extern struct page *empty_zero_page;
+#define ZERO_PAGE(vaddr)	(empty_zero_page)
+#endif
+
 #ifndef CONFIG_MMU
 
 #include <asm-generic/pgtable-nopud.h>
@@ -156,13 +165,6 @@
 #define __S111  __PAGE_SHARED_EXEC
 
 #ifndef __ASSEMBLY__
-/*
- * ZERO_PAGE is a global shared page that is always zero: used
- * for zero-mapped memory areas etc..
- */
-extern struct page *empty_zero_page;
-#define ZERO_PAGE(vaddr)	(empty_zero_page)
-
 
 extern pgd_t swapper_pg_dir[PTRS_PER_PGD];
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/processor.h
@@ -96,6 +96,7 @@
 #define __ALT_SMP_ASM(smp, up)						\
 	"9998:	" smp "\n"						\
 	"	.pushsection \".alt.smp.init\", \"a\"\n"		\
+	"	.align	2\n"						\
 	"	.long	9998b - .\n"					\
 	"	" up "\n"						\
 	"	.popsection\n"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/ptrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/ptrace.h
@@ -163,5 +163,31 @@
 		((current_stack_pointer | (THREAD_SIZE - 1)) - 7) - 1;	\
 })
 
+
+/*
+ * Update ITSTATE after normal execution of an IT block instruction.
+ *
+ * The 8 IT state bits are split into two parts in CPSR:
+ *	ITSTATE<1:0> are in CPSR<26:25>
+ *	ITSTATE<7:2> are in CPSR<15:10>
+ */
+static inline unsigned long it_advance(unsigned long cpsr)
+{
+	if ((cpsr & 0x06000400) == 0) {
+		/* ITSTATE<2:0> == 0 means end of IT block, so clear IT state */
+		cpsr &= ~PSR_IT_MASK;
+	} else {
+		/* We need to shift left ITSTATE<4:0> */
+		const unsigned long mask = 0x06001c00;  /* Mask ITSTATE<4:0> */
+		unsigned long it = cpsr & mask;
+		it <<= 1;
+		it |= it >> (27 - 10);  /* Carry ITSTATE<2> to correct place */
+		it &= mask;
+		cpsr &= ~mask;
+		cpsr |= it;
+	}
+	return cpsr;
+}
+
 #endif /* __ASSEMBLY__ */
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/smp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/smp.h
@@ -25,11 +25,6 @@
 extern void show_ipi_list(struct seq_file *, int);
 
 /*
- * Called from assembly code, this handles an IPI.
- */
-asmlinkage void do_IPI(int ipinr, struct pt_regs *regs);
-
-/*
  * Called from C code, this handles an IPI.
  */
 void handle_IPI(int ipinr, struct pt_regs *regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/spectre.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/spectre.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __ASM_SPECTRE_H
+#define __ASM_SPECTRE_H
+
+enum {
+	SPECTRE_UNAFFECTED,
+	SPECTRE_MITIGATED,
+	SPECTRE_VULNERABLE,
+};
+
+enum {
+	__SPECTRE_V2_METHOD_BPIALL,
+	__SPECTRE_V2_METHOD_ICIALLU,
+	__SPECTRE_V2_METHOD_SMC,
+	__SPECTRE_V2_METHOD_HVC,
+	__SPECTRE_V2_METHOD_LOOP8,
+};
+
+enum {
+	SPECTRE_V2_METHOD_BPIALL = BIT(__SPECTRE_V2_METHOD_BPIALL),
+	SPECTRE_V2_METHOD_ICIALLU = BIT(__SPECTRE_V2_METHOD_ICIALLU),
+	SPECTRE_V2_METHOD_SMC = BIT(__SPECTRE_V2_METHOD_SMC),
+	SPECTRE_V2_METHOD_HVC = BIT(__SPECTRE_V2_METHOD_HVC),
+	SPECTRE_V2_METHOD_LOOP8 = BIT(__SPECTRE_V2_METHOD_LOOP8),
+};
+
+#ifdef CONFIG_GENERIC_CPU_VULNERABILITIES
+void spectre_v2_update_state(unsigned int state, unsigned int methods);
+#else
+static inline void spectre_v2_update_state(unsigned int state,
+					   unsigned int methods)
+{}
+#endif
+
+int spectre_bhb_update_vectors(unsigned int method);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/sync_bitops.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/sync_bitops.h
@@ -14,14 +14,35 @@
  * ops which are SMP safe even on a UP kernel.
  */
 
+/*
+ * Unordered
+ */
+
 #define sync_set_bit(nr, p)		_set_bit(nr, p)
 #define sync_clear_bit(nr, p)		_clear_bit(nr, p)
 #define sync_change_bit(nr, p)		_change_bit(nr, p)
-#define sync_test_and_set_bit(nr, p)	_test_and_set_bit(nr, p)
-#define sync_test_and_clear_bit(nr, p)	_test_and_clear_bit(nr, p)
-#define sync_test_and_change_bit(nr, p)	_test_and_change_bit(nr, p)
 #define sync_test_bit(nr, addr)		test_bit(nr, addr)
-#define arch_sync_cmpxchg		arch_cmpxchg
 
+/*
+ * Fully ordered
+ */
+
+int _sync_test_and_set_bit(int nr, volatile unsigned long * p);
+#define sync_test_and_set_bit(nr, p)	_sync_test_and_set_bit(nr, p)
+
+int _sync_test_and_clear_bit(int nr, volatile unsigned long * p);
+#define sync_test_and_clear_bit(nr, p)	_sync_test_and_clear_bit(nr, p)
+
+int _sync_test_and_change_bit(int nr, volatile unsigned long * p);
+#define sync_test_and_change_bit(nr, p)	_sync_test_and_change_bit(nr, p)
+
+#define arch_sync_cmpxchg(ptr, old, new)				\
+({									\
+	__typeof__(*(ptr)) __ret;					\
+	__smp_mb__before_atomic();					\
+	__ret = arch_cmpxchg_relaxed((ptr), (old), (new));		\
+	__smp_mb__after_atomic();					\
+	__ret;								\
+})
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/syscall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/syscall.h
@@ -25,6 +25,9 @@
 	if (IS_ENABLED(CONFIG_AEABI) && !IS_ENABLED(CONFIG_OABI_COMPAT))
 		return task_thread_info(task)->abi_syscall;
 
+	if (task_thread_info(task)->abi_syscall == -1)
+		return -1;
+
 	return task_thread_info(task)->abi_syscall & __NR_SYSCALL_MASK;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/thread_info.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/thread_info.h
@@ -129,15 +129,16 @@
 #define TIF_NEED_RESCHED	1	/* rescheduling necessary */
 #define TIF_NOTIFY_RESUME	2	/* callback before returning to user */
 #define TIF_UPROBE		3	/* breakpointed or singlestepping */
-#define TIF_SYSCALL_TRACE	4	/* syscall trace active */
-#define TIF_SYSCALL_AUDIT	5	/* syscall auditing active */
-#define TIF_SYSCALL_TRACEPOINT	6	/* syscall tracepoint instrumentation */
-#define TIF_SECCOMP		7	/* seccomp syscall filtering active */
-#define TIF_NOTIFY_SIGNAL	8	/* signal notifications exist */
+#define TIF_NOTIFY_SIGNAL	4	/* signal notifications exist */
 
 #define TIF_USING_IWMMXT	17
 #define TIF_MEMDIE		18	/* is terminating due to OOM killer */
-#define TIF_RESTORE_SIGMASK	20
+#define TIF_RESTORE_SIGMASK	19
+#define TIF_SYSCALL_TRACE	20	/* syscall trace active */
+#define TIF_SYSCALL_AUDIT	21	/* syscall auditing active */
+#define TIF_SYSCALL_TRACEPOINT	22	/* syscall tracepoint instrumentation */
+#define TIF_SECCOMP		23	/* seccomp syscall filtering active */
+
 
 #define _TIF_SIGPENDING		(1 << TIF_SIGPENDING)
 #define _TIF_NEED_RESCHED	(1 << TIF_NEED_RESCHED)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/timex.h
@@ -11,5 +11,6 @@
 
 typedef unsigned long cycles_t;
 #define get_cycles()	({ cycles_t c; read_current_timer(&c) ? 0 : c; })
+#define random_get_entropy() (((unsigned long)get_cycles()) ?: random_get_entropy_fallback())
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/uaccess.h
@@ -11,6 +11,7 @@
 #include <linux/string.h>
 #include <asm/memory.h>
 #include <asm/domain.h>
+#include <asm/unaligned.h>
 #include <asm/unified.h>
 #include <asm/compiler.h>
 
@@ -123,16 +124,6 @@
 extern int __get_user_64t_2(void *);
 extern int __get_user_64t_4(void *);
 
-#define __GUP_CLOBBER_1	"lr", "cc"
-#ifdef CONFIG_CPU_USE_DOMAINS
-#define __GUP_CLOBBER_2	"ip", "lr", "cc"
-#else
-#define __GUP_CLOBBER_2 "lr", "cc"
-#endif
-#define __GUP_CLOBBER_4	"lr", "cc"
-#define __GUP_CLOBBER_32t_8 "lr", "cc"
-#define __GUP_CLOBBER_8	"lr", "cc"
-
 #define __get_user_x(__r2, __p, __e, __l, __s)				\
 	   __asm__ __volatile__ (					\
 		__asmeq("%0", "r0") __asmeq("%1", "r2")			\
@@ -140,7 +131,7 @@
 		"bl	__get_user_" #__s				\
 		: "=&r" (__e), "=r" (__r2)				\
 		: "0" (__p), "r" (__l)					\
-		: __GUP_CLOBBER_##__s)
+		: "ip", "lr", "cc")
 
 /* narrowing a double-word get into a single 32bit word register: */
 #ifdef __ARMEB__
@@ -162,7 +153,7 @@
 		"bl	__get_user_64t_" #__s				\
 		: "=&r" (__e), "=r" (__r2)				\
 		: "0" (__p), "r" (__l)					\
-		: __GUP_CLOBBER_##__s)
+		: "ip", "lr", "cc")
 #else
 #define __get_user_x_64t __get_user_x
 #endif
@@ -497,7 +488,10 @@
 	}								\
 	default: __err = __get_user_bad(); break;			\
 	}								\
-	*(type *)(dst) = __val;						\
+	if (IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS))		\
+		put_unaligned(__val, (type *)(dst));			\
+	else								\
+		*(type *)(dst) = __val; /* aligned by caller */		\
 	if (__err)							\
 		goto err_label;						\
 } while (0)
@@ -507,7 +501,9 @@
 	const type *__pk_ptr = (dst);					\
 	unsigned long __dst = (unsigned long)__pk_ptr;			\
 	int __err = 0;							\
-	type __val = *(type *)src;					\
+	type __val = IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS)	\
+		     ? get_unaligned((type *)(src))			\
+		     : *(type *)(src);	/* aligned by caller */		\
 	switch (sizeof(type)) {						\
 	case 1: __put_user_asm_byte(__val, __dst, __err, ""); break;	\
 	case 2:	__put_user_asm_half(__val, __dst, __err, ""); break;	\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/asm/vmlinux.lds.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/asm/vmlinux.lds.h
@@ -26,6 +26,19 @@
 #define ARM_MMU_DISCARD(x)	x
 #endif
 
+/*
+ * ld.lld does not support NOCROSSREFS:
+ * https://github.com/ClangBuiltLinux/linux/issues/1609
+ */
+#ifdef CONFIG_LD_IS_LLD
+#define NOCROSSREFS
+#endif
+
+/* Set start/end symbol names to the LMA for the section */
+#define ARM_LMA(sym, section)						\
+	sym##_start = LOADADDR(section);				\
+	sym##_end = LOADADDR(section) + SIZEOF(section)
+
 #define PROC_INFO							\
 		. = ALIGN(4);						\
 		__proc_info_begin = .;					\
@@ -110,19 +123,31 @@
  * only thing that matters is their relative offsets
  */
 #define ARM_VECTORS							\
-	__vectors_start = .;						\
-	.vectors 0xffff0000 : AT(__vectors_start) {			\
-		*(.vectors)						\
+	__vectors_lma = .;						\
+	OVERLAY 0xffff0000 : NOCROSSREFS AT(__vectors_lma) {		\
+		.vectors {						\
+			*(.vectors)					\
+		}							\
+		.vectors.bhb.loop8 {					\
+			*(.vectors.bhb.loop8)				\
+		}							\
+		.vectors.bhb.bpiall {					\
+			*(.vectors.bhb.bpiall)				\
+		}							\
 	}								\
-	. = __vectors_start + SIZEOF(.vectors);				\
-	__vectors_end = .;						\
+	ARM_LMA(__vectors, .vectors);					\
+	ARM_LMA(__vectors_bhb_loop8, .vectors.bhb.loop8);		\
+	ARM_LMA(__vectors_bhb_bpiall, .vectors.bhb.bpiall);		\
+	. = __vectors_lma + SIZEOF(.vectors) +				\
+		SIZEOF(.vectors.bhb.loop8) +				\
+		SIZEOF(.vectors.bhb.bpiall);				\
 									\
-	__stubs_start = .;						\
-	.stubs ADDR(.vectors) + 0x1000 : AT(__stubs_start) {		\
+	__stubs_lma = .;						\
+	.stubs ADDR(.vectors) + 0x1000 : AT(__stubs_lma) {		\
 		*(.stubs)						\
 	}								\
-	. = __stubs_start + SIZEOF(.stubs);				\
-	__stubs_end = .;						\
+	ARM_LMA(__stubs, .stubs);					\
+	. = __stubs_lma + SIZEOF(.stubs);				\
 									\
 	PROVIDE(vector_fiq_offset = vector_fiq - ADDR(.vectors));
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/include/debug/imx-uart.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/include/debug/imx-uart.h
@@ -11,13 +11,6 @@
 #define IMX1_UART_BASE_ADDR(n)	IMX1_UART##n##_BASE_ADDR
 #define IMX1_UART_BASE(n)	IMX1_UART_BASE_ADDR(n)
 
-#define IMX21_UART1_BASE_ADDR	0x1000a000
-#define IMX21_UART2_BASE_ADDR	0x1000b000
-#define IMX21_UART3_BASE_ADDR	0x1000c000
-#define IMX21_UART4_BASE_ADDR	0x1000d000
-#define IMX21_UART_BASE_ADDR(n)	IMX21_UART##n##_BASE_ADDR
-#define IMX21_UART_BASE(n)	IMX21_UART_BASE_ADDR(n)
-
 #define IMX25_UART1_BASE_ADDR	0x43f90000
 #define IMX25_UART2_BASE_ADDR	0x43f94000
 #define IMX25_UART3_BASE_ADDR	0x5000c000
@@ -26,6 +19,13 @@
 #define IMX25_UART_BASE_ADDR(n)	IMX25_UART##n##_BASE_ADDR
 #define IMX25_UART_BASE(n)	IMX25_UART_BASE_ADDR(n)
 
+#define IMX27_UART1_BASE_ADDR	0x1000a000
+#define IMX27_UART2_BASE_ADDR	0x1000b000
+#define IMX27_UART3_BASE_ADDR	0x1000c000
+#define IMX27_UART4_BASE_ADDR	0x1000d000
+#define IMX27_UART_BASE_ADDR(n)	IMX27_UART##n##_BASE_ADDR
+#define IMX27_UART_BASE(n)	IMX27_UART_BASE_ADDR(n)
+
 #define IMX31_UART1_BASE_ADDR	0x43f90000
 #define IMX31_UART2_BASE_ADDR	0x43f94000
 #define IMX31_UART3_BASE_ADDR	0x5000c000
@@ -112,10 +112,10 @@
 
 #ifdef CONFIG_DEBUG_IMX1_UART
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX1)
-#elif defined(CONFIG_DEBUG_IMX21_IMX27_UART)
-#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX21)
 #elif defined(CONFIG_DEBUG_IMX25_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX25)
+#elif defined(CONFIG_DEBUG_IMX27_UART)
+#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX27)
 #elif defined(CONFIG_DEBUG_IMX31_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX31)
 #elif defined(CONFIG_DEBUG_IMX35_UART)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/Makefile
@@ -106,4 +106,6 @@
 
 obj-$(CONFIG_HAVE_ARM_SMCCC)	+= smccc-call.o
 
+obj-$(CONFIG_GENERIC_CPU_VULNERABILITIES) += spectre.o
+
 extra-y := $(head-y) vmlinux.lds
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/bugs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/bugs.c
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <linux/init.h>
+#include <linux/cpu.h>
 #include <asm/bugs.h>
 #include <asm/proc-fns.h>
 
@@ -11,7 +12,7 @@
 #endif
 }
 
-void __init check_bugs(void)
+void __init arch_cpu_finalize_init(void)
 {
 	check_writebuffer_bugs();
 	check_other_bugs();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/entry-armv.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/entry-armv.S
@@ -597,11 +597,9 @@
 	tstne	r0, #0x04000000			@ bit 26 set on both ARM and Thumb-2
 	reteq	lr
 	and	r8, r0, #0x00000f00		@ mask out CP number
- THUMB(	lsr	r8, r8, #8		)
 	mov	r7, #1
-	add	r6, r10, #TI_USED_CP
- ARM(	strb	r7, [r6, r8, lsr #8]	)	@ set appropriate used_cp[]
- THUMB(	strb	r7, [r6, r8]		)	@ set appropriate used_cp[]
+	add	r6, r10, r8, lsr #8		@ add used_cp[] array offset first
+	strb	r7, [r6, #TI_USED_CP]		@ set appropriate used_cp[]
 #ifdef CONFIG_IWMMXT
 	@ Test if we need to give access to iWMMXt coprocessors
 	ldr	r5, [r10, #TI_FLAGS]
@@ -610,7 +608,7 @@
 	bcs	iwmmxt_task_enable
 #endif
  ARM(	add	pc, pc, r8, lsr #6	)
- THUMB(	lsl	r8, r8, #2		)
+ THUMB(	lsr	r8, r8, #6		)
  THUMB(	add	pc, r8			)
 	nop
 
@@ -1002,12 +1000,11 @@
 	sub	lr, lr, #\correction
 	.endif
 
-	@
-	@ Save r0, lr_<exception> (parent PC) and spsr_<exception>
-	@ (parent CPSR)
-	@
+	@ Save r0, lr_<exception> (parent PC)
 	stmia	sp, {r0, lr}		@ save r0, lr
-	mrs	lr, spsr
+
+	@ Save spsr_<exception> (parent CPSR)
+2:	mrs	lr, spsr
 	str	lr, [sp, #8]		@ save spsr
 
 	@
@@ -1028,6 +1025,44 @@
 	movs	pc, lr			@ branch to handler in SVC mode
 ENDPROC(vector_\name)
 
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+	.subsection 1
+	.align 5
+vector_bhb_loop8_\name:
+	.if \correction
+	sub	lr, lr, #\correction
+	.endif
+
+	@ Save r0, lr_<exception> (parent PC)
+	stmia	sp, {r0, lr}
+
+	@ bhb workaround
+	mov	r0, #8
+3:	W(b)	. + 4
+	subs	r0, r0, #1
+	bne	3b
+	dsb
+	isb
+	b	2b
+ENDPROC(vector_bhb_loop8_\name)
+
+vector_bhb_bpiall_\name:
+	.if \correction
+	sub	lr, lr, #\correction
+	.endif
+
+	@ Save r0, lr_<exception> (parent PC)
+	stmia	sp, {r0, lr}
+
+	@ bhb workaround
+	mcr	p15, 0, r0, c7, c5, 6	@ BPIALL
+	@ isb not needed due to "movs pc, lr" in the vector stub
+	@ which gives a "context synchronisation".
+	b	2b
+ENDPROC(vector_bhb_bpiall_\name)
+	.previous
+#endif
+
 	.align	2
 	@ handler addresses follow this label
 1:
@@ -1036,6 +1071,10 @@
 	.section .stubs, "ax", %progbits
 	@ This must be the first word
 	.word	vector_swi
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+	.word	vector_bhb_loop8_swi
+	.word	vector_bhb_bpiall_swi
+#endif
 
 vector_rst:
  ARM(	swi	SYS_ERROR0	)
@@ -1150,8 +1189,10 @@
  * FIQ "NMI" handler
  *-----------------------------------------------------------------------------
  * Handle a FIQ using the SVC stack allowing FIQ act like NMI on x86
- * systems.
+ * systems. This must be the last vector stub, so lets place it in its own
+ * subsection.
  */
+	.subsection 2
 	vector_stub	fiq, FIQ_MODE, 4
 
 	.long	__fiq_usr			@  0  (USR_26 / USR_32)
@@ -1184,6 +1225,30 @@
 	W(b)	vector_irq
 	W(b)	vector_fiq
 
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+	.section .vectors.bhb.loop8, "ax", %progbits
+.L__vectors_bhb_loop8_start:
+	W(b)	vector_rst
+	W(b)	vector_bhb_loop8_und
+	W(ldr)	pc, .L__vectors_bhb_loop8_start + 0x1004
+	W(b)	vector_bhb_loop8_pabt
+	W(b)	vector_bhb_loop8_dabt
+	W(b)	vector_addrexcptn
+	W(b)	vector_bhb_loop8_irq
+	W(b)	vector_bhb_loop8_fiq
+
+	.section .vectors.bhb.bpiall, "ax", %progbits
+.L__vectors_bhb_bpiall_start:
+	W(b)	vector_rst
+	W(b)	vector_bhb_bpiall_und
+	W(ldr)	pc, .L__vectors_bhb_bpiall_start + 0x1008
+	W(b)	vector_bhb_bpiall_pabt
+	W(b)	vector_bhb_bpiall_dabt
+	W(b)	vector_addrexcptn
+	W(b)	vector_bhb_bpiall_irq
+	W(b)	vector_bhb_bpiall_fiq
+#endif
+
 	.data
 	.align	2
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/entry-common.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/entry-common.S
@@ -101,6 +101,7 @@
 	cmp	r0, #0
 	beq	no_work_pending
 	movlt	scno, #(__NR_restart_syscall - __NR_SYSCALL_BASE)
+	str	scno, [tsk, #TI_ABI_SYSCALL]	@ make sure tracers see update
 	ldmia	sp, {r0 - r6}			@ have to reload r0 - r6
 	b	local_restart			@ ... and off we go
 ENDPROC(ret_fast_syscall)
@@ -154,12 +155,36 @@
  */
 
 	.align	5
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+ENTRY(vector_bhb_loop8_swi)
+	sub	sp, sp, #PT_REGS_SIZE
+	stmia	sp, {r0 - r12}
+	mov	r8, #8
+1:	b	2f
+2:	subs	r8, r8, #1
+	bne	1b
+	dsb
+	isb
+	b	3f
+ENDPROC(vector_bhb_loop8_swi)
+
+	.align	5
+ENTRY(vector_bhb_bpiall_swi)
+	sub	sp, sp, #PT_REGS_SIZE
+	stmia	sp, {r0 - r12}
+	mcr	p15, 0, r8, c7, c5, 6	@ BPIALL
+	isb
+	b	3f
+ENDPROC(vector_bhb_bpiall_swi)
+#endif
+	.align	5
 ENTRY(vector_swi)
 #ifdef CONFIG_CPU_V7M
 	v7m_exception_entry
 #else
 	sub	sp, sp, #PT_REGS_SIZE
 	stmia	sp, {r0 - r12}			@ Calling r0 - r12
+3:
  ARM(	add	r8, sp, #S_PC		)
  ARM(	stmdb	r8, {sp, lr}^		)	@ Calling sp, lr
  THUMB(	mov	r8, sp			)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/entry-ftrace.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/entry-ftrace.S
@@ -22,10 +22,7 @@
  * mcount can be thought of as a function called in the middle of a subroutine
  * call.  As such, it needs to be transparent for both the caller and the
  * callee: the original lr needs to be restored when leaving mcount, and no
- * registers should be clobbered.  (In the __gnu_mcount_nc implementation, we
- * clobber the ip register.  This is OK because the ARM calling convention
- * allows it to be clobbered in subroutines and doesn't use it to hold
- * parameters.)
+ * registers should be clobbered.
  *
  * When using dynamic ftrace, we patch out the mcount call by a "pop {lr}"
  * instead of the __gnu_mcount_nc call (see arch/arm/kernel/ftrace.c).
@@ -70,26 +67,25 @@
 
 .macro __ftrace_regs_caller
 
-	sub	sp, sp, #8	@ space for PC and CPSR OLD_R0,
+	str	lr, [sp, #-8]!	@ store LR as PC and make space for CPSR/OLD_R0,
 				@ OLD_R0 will overwrite previous LR
 
-	add 	ip, sp, #12	@ move in IP the value of SP as it was
-				@ before the push {lr} of the mcount mechanism
+	ldr	lr, [sp, #8]    @ get previous LR
 
-	str     lr, [sp, #0]    @ store LR instead of PC
+	str	r0, [sp, #8]	@ write r0 as OLD_R0 over previous LR
 
-	ldr     lr, [sp, #8]    @ get previous LR
+	str	lr, [sp, #-4]!	@ store previous LR as LR
 
-	str	r0, [sp, #8]	@ write r0 as OLD_R0 over previous LR
+	add 	lr, sp, #16	@ move in LR the value of SP as it was
+				@ before the push {lr} of the mcount mechanism
 
-	stmdb   sp!, {ip, lr}
-	stmdb   sp!, {r0-r11, lr}
+	push	{r0-r11, ip, lr}
 
 	@ stack content at this point:
 	@ 0  4          48   52       56            60   64    68       72
-	@ R0 | R1 | ... | LR | SP + 4 | previous LR | LR | PSR | OLD_R0 |
+	@ R0 | R1 | ... | IP | SP + 4 | previous LR | LR | PSR | OLD_R0 |
 
-	mov r3, sp				@ struct pt_regs*
+	mov	r3, sp				@ struct pt_regs*
 
 	ldr r2, =function_trace_op
 	ldr r2, [r2]				@ pointer to the current
@@ -112,11 +108,9 @@
 #endif
 
 	@ pop saved regs
-	ldmia   sp!, {r0-r12}			@ restore r0 through r12
-	ldr	ip, [sp, #8]			@ restore PC
-	ldr	lr, [sp, #4]			@ restore LR
-	ldr	sp, [sp, #0]			@ restore SP
-	mov	pc, ip				@ return
+	pop	{r0-r11, ip, lr}		@ restore r0 through r12
+	ldr	lr, [sp], #4			@ restore LR
+	ldr	pc, [sp], #12
 .endm
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
@@ -132,11 +126,9 @@
 	bl	prepare_ftrace_return
 
 	@ pop registers saved in ftrace_regs_caller
-	ldmia   sp!, {r0-r12}			@ restore r0 through r12
-	ldr	ip, [sp, #8]			@ restore PC
-	ldr	lr, [sp, #4]			@ restore LR
-	ldr	sp, [sp, #0]			@ restore SP
-	mov	pc, ip				@ return
+	pop	{r0-r11, ip, lr}		@ restore r0 through r12
+	ldr	lr, [sp], #4			@ restore LR
+	ldr	pc, [sp], #12
 
 .endm
 #endif
@@ -202,16 +194,17 @@
 .endm
 
 .macro mcount_exit
-	ldmia	sp!, {r0-r3, ip, lr}
-	ret	ip
+	ldmia	sp!, {r0-r3}
+	ldr	lr, [sp, #4]
+	ldr	pc, [sp], #8
 .endm
 
 ENTRY(__gnu_mcount_nc)
 UNWIND(.fnstart)
 #ifdef CONFIG_DYNAMIC_FTRACE
-	mov	ip, lr
-	ldmia	sp!, {lr}
-	ret	ip
+	push	{lr}
+	ldr	lr, [sp, #4]
+	ldr	pc, [sp], #8
 #else
 	__mcount
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/head-nommu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/head-nommu.S
@@ -114,6 +114,7 @@
 	add	r12, r12, r10
 	ret	r12
 1:	bl	__after_proc_init
+	ldr	r7, __secondary_data		@ reload r7
 	ldr	sp, [r7, #12]			@ set up the stack pointer
 	mov	fp, #0
 	b	secondary_start_kernel
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/head.S
@@ -252,18 +252,23 @@
 	 */
 	add	r0, r4, #KERNEL_OFFSET >> (SECTION_SHIFT - PMD_ORDER)
 	ldr	r6, =(_end - 1)
+
+	/* For XIP, kernel_sec_start/kernel_sec_end are currently in RO memory */
+#ifndef CONFIG_XIP_KERNEL
 	adr_l	r5, kernel_sec_start		@ _pa(kernel_sec_start)
 #if defined CONFIG_CPU_ENDIAN_BE8 || defined CONFIG_CPU_ENDIAN_BE32
 	str	r8, [r5, #4]			@ Save physical start of kernel (BE)
 #else
 	str	r8, [r5]			@ Save physical start of kernel (LE)
 #endif
+#endif
 	orr	r3, r8, r7			@ Add the MMU flags
 	add	r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
 1:	str	r3, [r0], #1 << PMD_ORDER
 	add	r3, r3, #1 << SECTION_SHIFT
 	cmp	r0, r6
 	bls	1b
+#ifndef CONFIG_XIP_KERNEL
 	eor	r3, r3, r7			@ Remove the MMU flags
 	adr_l	r5, kernel_sec_end		@ _pa(kernel_sec_end)
 #if defined CONFIG_CPU_ENDIAN_BE8 || defined CONFIG_CPU_ENDIAN_BE32
@@ -271,8 +276,7 @@
 #else
 	str	r3, [r5]			@ Save physical end of kernel (LE)
 #endif
-
-#ifdef CONFIG_XIP_KERNEL
+#else
 	/*
 	 * Map the kernel image separately as it is not located in RAM.
 	 */
@@ -407,7 +411,11 @@
 	/*
 	 * Use the page tables supplied from  __cpu_up.
 	 */
+#ifdef CONFIG_XIP_KERNEL
+	ldr	r3, =(secondary_data + PLAT_PHYS_OFFSET - PAGE_OFFSET)
+#else
 	adr_l	r3, secondary_data
+#endif
 	mov_l	r12, __secondary_switched
 	ldrd	r4, r5, [r3, #0]		@ get secondary_data.pgdir
 ARM_BE8(eor	r4, r4, r5)			@ Swap r5 and r4 in BE:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/hw_breakpoint.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/hw_breakpoint.c
@@ -626,7 +626,7 @@
 	hw->address &= ~alignment_mask;
 	hw->ctrl.len <<= offset;
 
-	if (is_default_overflow_handler(bp)) {
+	if (uses_default_overflow_handler(bp)) {
 		/*
 		 * Mismatch breakpoints are required for single-stepping
 		 * breakpoints.
@@ -798,7 +798,7 @@
 		 * Otherwise, insert a temporary mismatch breakpoint so that
 		 * we can single-step over the watchpoint trigger.
 		 */
-		if (!is_default_overflow_handler(wp))
+		if (!uses_default_overflow_handler(wp))
 			continue;
 step:
 		enable_single_step(wp, instruction_pointer(regs));
@@ -811,7 +811,7 @@
 		info->trigger = addr;
 		pr_debug("watchpoint fired: address = 0x%x\n", info->trigger);
 		perf_bp_event(wp, regs);
-		if (is_default_overflow_handler(wp))
+		if (uses_default_overflow_handler(wp))
 			enable_single_step(wp, instruction_pointer(regs));
 	}
 
@@ -886,7 +886,7 @@
 			info->trigger = addr;
 			pr_debug("breakpoint fired: address = 0x%x\n", addr);
 			perf_bp_event(bp, regs);
-			if (is_default_overflow_handler(bp))
+			if (uses_default_overflow_handler(bp))
 				enable_single_step(bp, addr);
 			goto unlock;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/kgdb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/kgdb.c
@@ -154,22 +154,38 @@
 	return 0;
 }
 
-static struct undef_hook kgdb_brkpt_hook = {
+static struct undef_hook kgdb_brkpt_arm_hook = {
 	.instr_mask		= 0xffffffff,
 	.instr_val		= KGDB_BREAKINST,
-	.cpsr_mask		= MODE_MASK,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
 	.cpsr_val		= SVC_MODE,
 	.fn			= kgdb_brk_fn
 };
 
-static struct undef_hook kgdb_compiled_brkpt_hook = {
+static struct undef_hook kgdb_brkpt_thumb_hook = {
+	.instr_mask		= 0xffff,
+	.instr_val		= KGDB_BREAKINST & 0xffff,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
+	.cpsr_val		= PSR_T_BIT | SVC_MODE,
+	.fn			= kgdb_brk_fn
+};
+
+static struct undef_hook kgdb_compiled_brkpt_arm_hook = {
 	.instr_mask		= 0xffffffff,
 	.instr_val		= KGDB_COMPILED_BREAK,
-	.cpsr_mask		= MODE_MASK,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
 	.cpsr_val		= SVC_MODE,
 	.fn			= kgdb_compiled_brk_fn
 };
 
+static struct undef_hook kgdb_compiled_brkpt_thumb_hook = {
+	.instr_mask		= 0xffff,
+	.instr_val		= KGDB_COMPILED_BREAK & 0xffff,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
+	.cpsr_val		= PSR_T_BIT | SVC_MODE,
+	.fn			= kgdb_compiled_brk_fn
+};
+
 static int __kgdb_notify(struct die_args *args, unsigned long cmd)
 {
 	struct pt_regs *regs = args->regs;
@@ -210,8 +226,10 @@
 	if (ret != 0)
 		return ret;
 
-	register_undef_hook(&kgdb_brkpt_hook);
-	register_undef_hook(&kgdb_compiled_brkpt_hook);
+	register_undef_hook(&kgdb_brkpt_arm_hook);
+	register_undef_hook(&kgdb_brkpt_thumb_hook);
+	register_undef_hook(&kgdb_compiled_brkpt_arm_hook);
+	register_undef_hook(&kgdb_compiled_brkpt_thumb_hook);
 
 	return 0;
 }
@@ -224,8 +242,10 @@
  */
 void kgdb_arch_exit(void)
 {
-	unregister_undef_hook(&kgdb_brkpt_hook);
-	unregister_undef_hook(&kgdb_compiled_brkpt_hook);
+	unregister_undef_hook(&kgdb_brkpt_arm_hook);
+	unregister_undef_hook(&kgdb_brkpt_thumb_hook);
+	unregister_undef_hook(&kgdb_compiled_brkpt_arm_hook);
+	unregister_undef_hook(&kgdb_compiled_brkpt_thumb_hook);
 	unregister_die_notifier(&kgdb_notifier);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/machine_kexec.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/machine_kexec.c
@@ -92,16 +92,28 @@
 	}
 }
 
+static DEFINE_PER_CPU(call_single_data_t, cpu_stop_csd) =
+	CSD_INIT(machine_crash_nonpanic_core, NULL);
+
 void crash_smp_send_stop(void)
 {
 	static int cpus_stopped;
 	unsigned long msecs;
+	call_single_data_t *csd;
+	int cpu, this_cpu = raw_smp_processor_id();
 
 	if (cpus_stopped)
 		return;
 
 	atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1);
-	smp_call_function(machine_crash_nonpanic_core, NULL, false);
+	for_each_online_cpu(cpu) {
+		if (cpu == this_cpu)
+			continue;
+
+		csd = &per_cpu(cpu_stop_csd, cpu);
+		smp_call_function_single_async(cpu, csd);
+	}
+
 	msecs = 1000; /* Wait at most a second for the other cpus to stop */
 	while ((atomic_read(&waiting_for_crash_ipi) > 0) && msecs) {
 		mdelay(1);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/module-plts.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/module-plts.c
@@ -256,7 +256,7 @@
 		/* sort by type and symbol index */
 		sort(rels, numrels, sizeof(Elf32_Rel), cmp_rel, NULL);
 
-		if (strncmp(secstrings + dstsec->sh_name, ".init", 5) != 0)
+		if (!module_init_layout_section(secstrings + dstsec->sh_name))
 			core_plts += count_plts(syms, dstsec->sh_addr, rels,
 						numrels, s->sh_info);
 		else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/perf_callchain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/perf_callchain.c
@@ -62,9 +62,10 @@
 void
 perf_callchain_user(struct perf_callchain_entry_ctx *entry, struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct frame_tail __user *tail;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -98,9 +99,10 @@
 void
 perf_callchain_kernel(struct perf_callchain_entry_ctx *entry, struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct stackframe fr;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -111,18 +113,21 @@
 
 unsigned long perf_instruction_pointer(struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
-		return perf_guest_cbs->get_guest_ip();
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
+
+	if (guest_cbs && guest_cbs->is_in_guest())
+		return guest_cbs->get_guest_ip();
 
 	return instruction_pointer(regs);
 }
 
 unsigned long perf_misc_flags(struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	int misc = 0;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		if (perf_guest_cbs->is_user_mode())
+	if (guest_cbs && guest_cbs->is_in_guest()) {
+		if (guest_cbs->is_user_mode())
 			misc |= PERF_RECORD_MISC_GUEST_USER;
 		else
 			misc |= PERF_RECORD_MISC_GUEST_KERNEL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/psci_smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/psci_smp.c
@@ -45,8 +45,15 @@
 static int psci_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	if (psci_ops.cpu_on)
+#ifdef CONFIG_XIP_KERNEL
+		return psci_ops.cpu_on(cpu_logical_map(cpu),
+			((phys_addr_t)(&secondary_startup)
+			- XIP_VIRT_ADDR(CONFIG_XIP_PHYS_ADDR)
+			+ CONFIG_XIP_PHYS_ADDR));
+#else
 		return psci_ops.cpu_on(cpu_logical_map(cpu),
 					virt_to_idmap(&secondary_startup));
+#endif
 	return -ENODEV;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/ptrace.c
@@ -786,8 +786,9 @@
 			break;
 
 		case PTRACE_SET_SYSCALL:
-			task_thread_info(child)->abi_syscall = data &
-							__NR_SYSCALL_MASK;
+			if (data != -1)
+				data &= __NR_SYSCALL_MASK;
+			task_thread_info(child)->abi_syscall = data;
 			ret = 0;
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/signal.c
@@ -708,6 +708,7 @@
 static_assert(offsetof(siginfo_t, si_pkey)	== 0x14);
 static_assert(offsetof(siginfo_t, si_perf_data)	== 0x10);
 static_assert(offsetof(siginfo_t, si_perf_type)	== 0x14);
+static_assert(offsetof(siginfo_t, si_perf_flags) == 0x18);
 static_assert(offsetof(siginfo_t, si_band)	== 0x0c);
 static_assert(offsetof(siginfo_t, si_fd)	== 0x10);
 static_assert(offsetof(siginfo_t, si_call_addr)	== 0x0c);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/sleep.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/sleep.S
@@ -114,6 +114,10 @@
 	.popsection
 cpu_resume_after_mmu:
 	bl	cpu_init		@ restore the und/abt/irq banked regs
+#if defined(CONFIG_KASAN) && defined(CONFIG_KASAN_STACK)
+	mov	r0, sp
+	bl	kasan_unpoison_task_stack_below
+#endif
 	mov	r0, #0			@ return zero on success
 	ldmfd	sp!, {r4 - r11, pc}
 ENDPROC(cpu_resume_after_mmu)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/smp.c
@@ -622,11 +622,6 @@
 /*
  * Main handler for inter-processor interrupts
  */
-asmlinkage void __exception_irq_entry do_IPI(int ipinr, struct pt_regs *regs)
-{
-	handle_IPI(ipinr, regs);
-}
-
 static void do_handle_IPI(int ipinr)
 {
 	unsigned int cpu = smp_processor_id();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/spectre.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/spectre.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/bpf.h>
+#include <linux/cpu.h>
+#include <linux/device.h>
+
+#include <asm/spectre.h>
+
+static bool _unprivileged_ebpf_enabled(void)
+{
+#ifdef CONFIG_BPF_SYSCALL
+	return !sysctl_unprivileged_bpf_disabled;
+#else
+	return false;
+#endif
+}
+
+ssize_t cpu_show_spectre_v1(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	return sprintf(buf, "Mitigation: __user pointer sanitization\n");
+}
+
+static unsigned int spectre_v2_state;
+static unsigned int spectre_v2_methods;
+
+void spectre_v2_update_state(unsigned int state, unsigned int method)
+{
+	if (state > spectre_v2_state)
+		spectre_v2_state = state;
+	spectre_v2_methods |= method;
+}
+
+ssize_t cpu_show_spectre_v2(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	const char *method;
+
+	if (spectre_v2_state == SPECTRE_UNAFFECTED)
+		return sprintf(buf, "%s\n", "Not affected");
+
+	if (spectre_v2_state != SPECTRE_MITIGATED)
+		return sprintf(buf, "%s\n", "Vulnerable");
+
+	if (_unprivileged_ebpf_enabled())
+		return sprintf(buf, "Vulnerable: Unprivileged eBPF enabled\n");
+
+	switch (spectre_v2_methods) {
+	case SPECTRE_V2_METHOD_BPIALL:
+		method = "Branch predictor hardening";
+		break;
+
+	case SPECTRE_V2_METHOD_ICIALLU:
+		method = "I-cache invalidation";
+		break;
+
+	case SPECTRE_V2_METHOD_SMC:
+	case SPECTRE_V2_METHOD_HVC:
+		method = "Firmware call";
+		break;
+
+	case SPECTRE_V2_METHOD_LOOP8:
+		method = "History overwrite";
+		break;
+
+	default:
+		method = "Multiple mitigations";
+		break;
+	}
+
+	return sprintf(buf, "Mitigation: %s\n", method);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/stacktrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/stacktrace.c
@@ -53,18 +53,17 @@
 		return -EINVAL;
 
 	frame->sp = frame->fp;
-	frame->fp = *(unsigned long *)(fp);
-	frame->pc = frame->lr;
-	frame->lr = *(unsigned long *)(fp + 4);
+	frame->fp = READ_ONCE_NOCHECK(*(unsigned long *)(fp));
+	frame->pc = READ_ONCE_NOCHECK(*(unsigned long *)(fp + 4));
 #else
 	/* check current frame pointer is within bounds */
 	if (fp < low + 12 || fp > high - 4)
 		return -EINVAL;
 
 	/* restore the registers from the stack frame */
-	frame->fp = *(unsigned long *)(fp - 12);
-	frame->sp = *(unsigned long *)(fp - 8);
-	frame->pc = *(unsigned long *)(fp - 4);
+	frame->fp = READ_ONCE_NOCHECK(*(unsigned long *)(fp - 12));
+	frame->sp = READ_ONCE_NOCHECK(*(unsigned long *)(fp - 8));
+	frame->pc = READ_ONCE_NOCHECK(*(unsigned long *)(fp - 4));
 #endif
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/swp_emulate.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/swp_emulate.c
@@ -195,7 +195,7 @@
 		 destreg, EXTRACT_REG_NUM(instr, RT2_OFFSET), data);
 
 	/* Check access in reasonable access range for both SWP and SWPB */
-	if (!access_ok((address & ~3), 4)) {
+	if (!access_ok((void __user *)(address & ~3), 4)) {
 		pr_debug("SWP{B} emulation: access to %p not allowed!\n",
 			 (void *)address);
 		res = -EFAULT;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/traps.c
@@ -30,6 +30,7 @@
 #include <linux/atomic.h>
 #include <asm/cacheflush.h>
 #include <asm/exception.h>
+#include <asm/spectre.h>
 #include <asm/unistd.h>
 #include <asm/traps.h>
 #include <asm/ptrace.h>
@@ -333,7 +334,7 @@
 	if (panic_on_oops)
 		panic("Fatal exception");
 	if (signr)
-		do_exit(signr);
+		make_task_dead(signr);
 }
 
 /*
@@ -574,7 +575,7 @@
 	if (end < start || flags)
 		return -EINVAL;
 
-	if (!access_ok(start, end - start))
+	if (!access_ok((void __user *)start, end - start))
 		return -EFAULT;
 
 	return __do_cache_op(start, end);
@@ -787,10 +788,59 @@
 }
 #endif
 
+#ifndef CONFIG_CPU_V7M
+static void copy_from_lma(void *vma, void *lma_start, void *lma_end)
+{
+	memcpy(vma, lma_start, lma_end - lma_start);
+}
+
+static void flush_vectors(void *vma, size_t offset, size_t size)
+{
+	unsigned long start = (unsigned long)vma + offset;
+	unsigned long end = start + size;
+
+	flush_icache_range(start, end);
+}
+
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+int spectre_bhb_update_vectors(unsigned int method)
+{
+	extern char __vectors_bhb_bpiall_start[], __vectors_bhb_bpiall_end[];
+	extern char __vectors_bhb_loop8_start[], __vectors_bhb_loop8_end[];
+	void *vec_start, *vec_end;
+
+	if (system_state > SYSTEM_SCHEDULING) {
+		pr_err("CPU%u: Spectre BHB workaround too late - system vulnerable\n",
+		       smp_processor_id());
+		return SPECTRE_VULNERABLE;
+	}
+
+	switch (method) {
+	case SPECTRE_V2_METHOD_LOOP8:
+		vec_start = __vectors_bhb_loop8_start;
+		vec_end = __vectors_bhb_loop8_end;
+		break;
+
+	case SPECTRE_V2_METHOD_BPIALL:
+		vec_start = __vectors_bhb_bpiall_start;
+		vec_end = __vectors_bhb_bpiall_end;
+		break;
+
+	default:
+		pr_err("CPU%u: unknown Spectre BHB state %d\n",
+		       smp_processor_id(), method);
+		return SPECTRE_VULNERABLE;
+	}
+
+	copy_from_lma(vectors_page, vec_start, vec_end);
+	flush_vectors(vectors_page, 0, vec_end - vec_start);
+
+	return SPECTRE_MITIGATED;
+}
+#endif
+
 void __init early_trap_init(void *vectors_base)
 {
-#ifndef CONFIG_CPU_V7M
-	unsigned long vectors = (unsigned long)vectors_base;
 	extern char __stubs_start[], __stubs_end[];
 	extern char __vectors_start[], __vectors_end[];
 	unsigned i;
@@ -811,17 +861,20 @@
 	 * into the vector page, mapped at 0xffff0000, and ensure these
 	 * are visible to the instruction stream.
 	 */
-	memcpy((void *)vectors, __vectors_start, __vectors_end - __vectors_start);
-	memcpy((void *)vectors + 0x1000, __stubs_start, __stubs_end - __stubs_start);
+	copy_from_lma(vectors_base, __vectors_start, __vectors_end);
+	copy_from_lma(vectors_base + 0x1000, __stubs_start, __stubs_end);
 
 	kuser_init(vectors_base);
 
-	flush_icache_range(vectors, vectors + PAGE_SIZE * 2);
+	flush_vectors(vectors_base, 0, PAGE_SIZE * 2);
+}
 #else /* ifndef CONFIG_CPU_V7M */
+void __init early_trap_init(void *vectors_base)
+{
 	/*
 	 * on V7-M there is no need to copy the vector table to a dedicated
 	 * memory area. The address is configurable and so a table in the kernel
 	 * image can be used.
 	 */
-#endif
 }
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/kernel/unwind.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/kernel/unwind.c
@@ -301,6 +301,29 @@
 	return URC_OK;
 }
 
+static unsigned long unwind_decode_uleb128(struct unwind_ctrl_block *ctrl)
+{
+	unsigned long bytes = 0;
+	unsigned long insn;
+	unsigned long result = 0;
+
+	/*
+	 * unwind_get_byte() will advance `ctrl` one instruction at a time, so
+	 * loop until we get an instruction byte where bit 7 is not set.
+	 *
+	 * Note: This decodes a maximum of 4 bytes to output 28 bits data where
+	 * max is 0xfffffff: that will cover a vsp increment of 1073742336, hence
+	 * it is sufficient for unwinding the stack.
+	 */
+	do {
+		insn = unwind_get_byte(ctrl);
+		result |= (insn & 0x7f) << (bytes * 7);
+		bytes++;
+	} while (!!(insn & 0x80) && (bytes != sizeof(result)));
+
+	return result;
+}
+
 /*
  * Execute the current unwind instruction.
  */
@@ -354,7 +377,7 @@
 		if (ret)
 			goto error;
 	} else if (insn == 0xb2) {
-		unsigned long uleb128 = unwind_get_byte(ctrl);
+		unsigned long uleb128 = unwind_decode_uleb128(ctrl);
 
 		ctrl->vrs[SP] += 0x204 + (uleb128 << 2);
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/bitops.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/bitops.h
@@ -28,7 +28,7 @@
 ENDPROC(\name		)
 	.endm
 
-	.macro	testop, name, instr, store
+	.macro	__testop, name, instr, store, barrier
 ENTRY(	\name		)
 UNWIND(	.fnstart	)
 	ands	ip, r1, #3
@@ -38,7 +38,7 @@
 	mov	r0, r0, lsr #5
 	add	r1, r1, r0, lsl #2	@ Get word offset
 	mov	r3, r2, lsl r3		@ create mask
-	smp_dmb
+	\barrier
 #if __LINUX_ARM_ARCH__ >= 7 && defined(CONFIG_SMP)
 	.arch_extension	mp
 	ALT_SMP(W(pldw)	[r1])
@@ -50,13 +50,21 @@
 	strex	ip, r2, [r1]
 	cmp	ip, #0
 	bne	1b
-	smp_dmb
+	\barrier
 	cmp	r0, #0
 	movne	r0, #1
 2:	bx	lr
 UNWIND(	.fnend		)
 ENDPROC(\name		)
 	.endm
+
+	.macro	testop, name, instr, store
+	__testop \name, \instr, \store, smp_dmb
+	.endm
+
+	.macro	sync_testop, name, instr, store
+	__testop \name, \instr, \store, __smp_dmb
+	.endm
 #else
 	.macro	bitop, name, instr
 ENTRY(	\name		)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/findbit.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/findbit.S
@@ -40,8 +40,8 @@
  * Prototype: int find_next_zero_bit(void *addr, unsigned int maxbit, int offset)
  */
 ENTRY(_find_next_zero_bit_le)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
  ARM(		ldrb	r3, [r0, r2, lsr #3]	)
@@ -81,8 +81,8 @@
  * Prototype: int find_next_zero_bit(void *addr, unsigned int maxbit, int offset)
  */
 ENTRY(_find_next_bit_le)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
  ARM(		ldrb	r3, [r0, r2, lsr #3]	)
@@ -115,8 +115,8 @@
 ENDPROC(_find_first_zero_bit_be)
 
 ENTRY(_find_next_zero_bit_be)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
 		eor	r3, r2, #0x18		@ big endian byte ordering
@@ -149,8 +149,8 @@
 ENDPROC(_find_first_bit_be)
 
 ENTRY(_find_next_bit_be)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
 		eor	r3, r2, #0x18		@ big endian byte ordering
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/memset.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/memset.S
@@ -17,6 +17,7 @@
 ENTRY(mmioset)
 WEAK(memset)
 UNWIND( .fnstart         )
+	and	r1, r1, #255		@ cast to unsigned char
 	ands	r3, r0, #3		@ 1 unaligned?
 	mov	ip, r0			@ preserve r0 as return value
 	bne	6f			@ 1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/testchangebit.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/testchangebit.S
@@ -10,3 +10,7 @@
                 .text
 
 testop	_test_and_change_bit, eor, str
+
+#if __LINUX_ARM_ARCH__ >= 6
+sync_testop	_sync_test_and_change_bit, eor, str
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/testclearbit.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/testclearbit.S
@@ -10,3 +10,7 @@
                 .text
 
 testop	_test_and_clear_bit, bicne, strne
+
+#if __LINUX_ARM_ARCH__ >= 6
+sync_testop	_sync_test_and_clear_bit, bicne, strne
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/testsetbit.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/testsetbit.S
@@ -10,3 +10,7 @@
                 .text
 
 testop	_test_and_set_bit, orreq, streq
+
+#if __LINUX_ARM_ARCH__ >= 6
+sync_testop	_sync_test_and_set_bit, orreq, streq
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/uaccess_with_memcpy.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/uaccess_with_memcpy.c
@@ -121,7 +121,7 @@
 			tocopy = n;
 
 		ua_flags = uaccess_save_and_enable();
-		memcpy((void *)to, from, tocopy);
+		__memcpy((void *)to, from, tocopy);
 		uaccess_restore(ua_flags);
 		to += tocopy;
 		from += tocopy;
@@ -188,7 +188,7 @@
 			tocopy = n;
 
 		ua_flags = uaccess_save_and_enable();
-		memset((void *)addr, 0, tocopy);
+		__memset((void *)addr, 0, tocopy);
 		uaccess_restore(ua_flags);
 		addr += tocopy;
 		n -= tocopy;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/lib/xor-neon.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/lib/xor-neon.c
@@ -26,8 +26,9 @@
  * While older versions of GCC do not generate incorrect code, they fail to
  * recognize the parallel nature of these functions, and emit plain ARM code,
  * which is known to be slower than the optimized ARM code in asm-arm/xor.h.
+ *
+ * #warning This code requires at least version 4.6 of GCC
  */
-#warning This code requires at least version 4.6 of GCC
 #endif
 
 #pragma GCC diagnostic ignored "-Wunused-variable"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-at91/pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-at91/pm.c
@@ -146,7 +146,7 @@
 
 static const struct of_device_id sama5d2_ws_ids[] = {
 	{ .compatible = "atmel,sama5d2-gem",		.data = &ws_info[0] },
-	{ .compatible = "atmel,at91rm9200-rtc",		.data = &ws_info[1] },
+	{ .compatible = "atmel,sama5d2-rtc",		.data = &ws_info[1] },
 	{ .compatible = "atmel,sama5d3-udc",		.data = &ws_info[2] },
 	{ .compatible = "atmel,at91rm9200-ohci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ohci",			.data = &ws_info[2] },
@@ -157,24 +157,24 @@
 };
 
 static const struct of_device_id sam9x60_ws_ids[] = {
-	{ .compatible = "atmel,at91sam9x5-rtc",		.data = &ws_info[1] },
+	{ .compatible = "microchip,sam9x60-rtc",	.data = &ws_info[1] },
 	{ .compatible = "atmel,at91rm9200-ohci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ohci",			.data = &ws_info[2] },
 	{ .compatible = "atmel,at91sam9g45-ehci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ehci",			.data = &ws_info[2] },
-	{ .compatible = "atmel,at91sam9260-rtt",	.data = &ws_info[4] },
+	{ .compatible = "microchip,sam9x60-rtt",	.data = &ws_info[4] },
 	{ .compatible = "cdns,sam9x60-macb",		.data = &ws_info[5] },
 	{ /* sentinel */ }
 };
 
 static const struct of_device_id sama7g5_ws_ids[] = {
-	{ .compatible = "atmel,at91sam9x5-rtc",		.data = &ws_info[1] },
+	{ .compatible = "microchip,sama7g5-rtc",	.data = &ws_info[1] },
 	{ .compatible = "microchip,sama7g5-ohci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ohci",			.data = &ws_info[2] },
 	{ .compatible = "atmel,at91sam9g45-ehci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ehci",			.data = &ws_info[2] },
 	{ .compatible = "microchip,sama7g5-sdhci",	.data = &ws_info[3] },
-	{ .compatible = "atmel,at91sam9260-rtt",	.data = &ws_info[4] },
+	{ .compatible = "microchip,sama7g5-rtt",	.data = &ws_info[4] },
 	{ /* sentinel */ }
 };
 
@@ -350,10 +350,42 @@
 
 static int at91_suspend_finish(unsigned long val)
 {
+	unsigned char modified_gray_code[] = {
+		0x00, 0x01, 0x02, 0x03, 0x06, 0x07, 0x04, 0x05, 0x0c, 0x0d,
+		0x0e, 0x0f, 0x0a, 0x0b, 0x08, 0x09, 0x18, 0x19, 0x1a, 0x1b,
+		0x1e, 0x1f, 0x1c, 0x1d, 0x14, 0x15, 0x16, 0x17, 0x12, 0x13,
+		0x10, 0x11,
+	};
+	unsigned int tmp, index;
 	int i;
 
 	if (soc_pm.data.mode == AT91_PM_BACKUP && soc_pm.data.ramc_phy) {
 		/*
+		 * Bootloader will perform DDR recalibration and will try to
+		 * restore the ZQ0SR0 with the value saved here. But the
+		 * calibration is buggy and restoring some values from ZQ0SR0
+		 * is forbidden and risky thus we need to provide processed
+		 * values for these (modified gray code values).
+		 */
+		tmp = readl(soc_pm.data.ramc_phy + DDR3PHY_ZQ0SR0);
+
+		/* Store pull-down output impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SR0_PDO_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] = modified_gray_code[index];
+
+		/* Store pull-up output impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SR0_PUO_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] |= modified_gray_code[index];
+
+		/* Store pull-down on-die termination impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SR0_PDODT_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] |= modified_gray_code[index];
+
+		/* Store pull-up on-die termination impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SRO_PUODT_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] |= modified_gray_code[index];
+
+		/*
 		 * The 1st 8 words of memory might get corrupted in the process
 		 * of DDR PHY recalibration; it is saved here in securam and it
 		 * will be restored later, after recalibration, by bootloader
@@ -371,7 +403,21 @@
 	return 0;
 }
 
-static void at91_pm_switch_ba_to_vbat(void)
+/**
+ * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
+ * to automatic/hardware mode.
+ *
+ * The Backup Unit Power Switch can be managed either by software or hardware.
+ * Enabling hardware mode allows the automatic transition of power between
+ * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
+ * availability of these power sources.
+ *
+ * If the Backup Unit Power Switch is already in automatic mode, no action is
+ * required. If it is in software-controlled mode, it is switched to automatic
+ * mode to enhance safety and eliminate the need for toggling between power
+ * sources.
+ */
+static void at91_pm_switch_ba_to_auto(void)
 {
 	unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
 	unsigned int val;
@@ -382,24 +428,19 @@
 
 	val = readl(soc_pm.data.sfrbu + offset);
 
-	/* Already on VBAT. */
-	if (!(val & soc_pm.sfrbu_regs.pswbu.state))
+	/* Already on auto/hardware. */
+	if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
 		return;
 
-	val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
-	val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
+	val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
+	val |= soc_pm.sfrbu_regs.pswbu.key;
 	writel(val, soc_pm.data.sfrbu + offset);
-
-	/* Wait for update. */
-	val = readl(soc_pm.data.sfrbu + offset);
-	while (val & soc_pm.sfrbu_regs.pswbu.state)
-		val = readl(soc_pm.data.sfrbu + offset);
 }
 
 static void at91_pm_suspend(suspend_state_t state)
 {
 	if (soc_pm.data.mode == AT91_PM_BACKUP) {
-		at91_pm_switch_ba_to_vbat();
+		at91_pm_switch_ba_to_auto();
 
 		cpu_suspend(0, at91_suspend_finish);
 
@@ -841,10 +882,6 @@
 		of_scan_flat_dt(at91_pm_backup_scan_memcs, &located);
 		if (!located)
 			goto securam_fail;
-
-		/* DDR3PHY_ZQ0SR0 */
-		soc_pm.bu->ddr_phy_calibration[0] = readl(soc_pm.data.ramc_phy +
-							  0x188);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-at91/pm_suspend.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-at91/pm_suspend.S
@@ -169,12 +169,23 @@
 	cmp	tmp1, #UDDRC_STAT_SELFREF_TYPE_SW
 	bne	sr_ena_2
 
-	/* Put DDR PHY's DLL in bypass mode for non-backup modes. */
+	/* Disable DX DLLs for non-backup modes. */
 	cmp	r7, #AT91_PM_BACKUP
 	beq	sr_ena_3
-	ldr	tmp1, [r3, #DDR3PHY_PIR]
-	orr	tmp1, tmp1, #DDR3PHY_PIR_DLLBYP
-	str	tmp1, [r3, #DDR3PHY_PIR]
+
+	/* Do not soft reset the AC DLL. */
+	ldr	tmp1, [r3, DDR3PHY_ACDLLCR]
+	bic	tmp1, tmp1, DDR3PHY_ACDLLCR_DLLSRST
+	str	tmp1, [r3, DDR3PHY_ACDLLCR]
+
+	/* Disable DX DLLs. */
+	ldr	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+	orr	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+
+	ldr	tmp1, [r3, #DDR3PHY_DX1DLLCR]
+	orr	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX1DLLCR]
 
 sr_ena_3:
 	/* Power down DDR PHY data receivers. */
@@ -221,10 +232,14 @@
 	bic	tmp1, tmp1, #DDR3PHY_DSGCR_ODTPDD_ODT0
 	str	tmp1, [r3, #DDR3PHY_DSGCR]
 
-	/* Take DDR PHY's DLL out of bypass mode. */
-	ldr	tmp1, [r3, #DDR3PHY_PIR]
-	bic	tmp1, tmp1, #DDR3PHY_PIR_DLLBYP
-	str	tmp1, [r3, #DDR3PHY_PIR]
+	/* Enable DX DLLs. */
+	ldr	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+	bic	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+
+	ldr	tmp1, [r3, #DDR3PHY_DX1DLLCR]
+	bic	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX1DLLCR]
 
 	/* Enable quasi-dynamic programming. */
 	mov	tmp1, #0
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-axxia/platsmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-axxia/platsmp.c
@@ -39,6 +39,7 @@
 		return -ENOENT;
 
 	syscon = of_iomap(syscon_np, 0);
+	of_node_put(syscon_np);
 	if (!syscon)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-bcm/bcm_kona_smc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-bcm/bcm_kona_smc.c
@@ -52,6 +52,7 @@
 		return -ENODEV;
 
 	prop_val = of_get_address(node, 0, &prop_size, NULL);
+	of_node_put(node);
 	if (!prop_val)
 		return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-cns3xxx/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-cns3xxx/core.c
@@ -372,6 +372,7 @@
 		/* De-Asscer SATA Reset */
 		cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SATA));
 	}
+	of_node_put(dn);
 
 	dn = of_find_compatible_node(NULL, NULL, "cavium,cns3420-sdhci");
 	if (of_device_is_available(dn)) {
@@ -385,6 +386,7 @@
 		cns3xxx_pwr_clk_en(CNS3XXX_PWR_CLK_EN(SDIO));
 		cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SDIO));
 	}
+	of_node_put(dn);
 
 	pm_power_off = cns3xxx_power_off;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/Kconfig
@@ -3,12 +3,14 @@
 menuconfig ARCH_DAVINCI
 	bool "TI DaVinci"
 	depends on ARCH_MULTI_V5
+	select CPU_ARM926T
 	select DAVINCI_TIMER
 	select ZONE_DMA
 	select PM_GENERIC_DOMAINS if PM
 	select PM_GENERIC_DOMAINS_OF if PM && OF
 	select REGMAP_MMIO
 	select RESET_CONTROLLER
+	select PINCTRL
 	select PINCTRL_SINGLE
 
 if ARCH_DAVINCI
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-da830-evm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-da830-evm.c
@@ -1,13 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA830/OMAP L137 EVM board
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  * Derived from: arch/arm/mach-davinci/board-dm644x-evm.c
  *
- * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007, 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-da850-evm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-da850-evm.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA850/OMAP-L138 EVM board
  *
@@ -6,10 +7,7 @@
  * Derived from: arch/arm/mach-davinci/board-da830-evm.c
  * Original Copyrights follow:
  *
- * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007, 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/console.h>
 #include <linux/delay.h>
@@ -1101,11 +1099,13 @@
 	int ret;
 	u32 val;
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
-	u8 rmii_en = soc_info->emac_pdata->rmii_en;
+	u8 rmii_en;
 
 	if (!machine_is_davinci_da850_evm())
 		return 0;
 
+	rmii_en = soc_info->emac_pdata->rmii_en;
+
 	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
 
 	val = __raw_readl(cfg_chip3_base);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-dm355-evm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-dm355-evm.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci EVM board support
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-dm355-leopard.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-dm355-leopard.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * DM355 leopard board support
  *
  * Based on board-dm355-evm.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-dm644x-evm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-dm644x-evm.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci EVM board support
  *
  * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-dm646x-evm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-dm646x-evm.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM646X EVM board
  *
@@ -5,11 +6,6 @@
  * Copyright (C) 2006 Texas Instruments.
  *
  * (C) 2007-2008, MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- *
  */
 
 /**************************************************************************
@@ -873,4 +869,3 @@
 	.init_late	= davinci_init_late,
 	.dma_zone_size	= SZ_128M,
 MACHINE_END
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-mityomapl138.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-mityomapl138.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Critical Link MityOMAP-L138 SoM
  *
  * Copyright (C) 2010 Critical Link LLC - https://www.criticallink.com
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of
- * any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "MityOMAPL138: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-neuros-osd2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-neuros-osd2.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Neuros Technologies OSD2 board support
  *
@@ -18,10 +19,6 @@
  *
  * For more information please refer to
  * 		http://wiki.neurostechnology.com/index.php/OSD_2.0_HD
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Hawkboard.org based on TI's OMAP-L138 Platform
  *
  * Initial code: Syed Mohammed Khasim
  *
  * Copyright (C) 2009 Texas Instruments Incorporated - https://www.ti.com
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of
- * any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/common.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Code commons to all DaVinci SoCs.
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/module.h>
 #include <linux/io.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/cpuidle.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/cpuidle.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * TI DaVinci cpuidle platform support
  *
  * 2009 (C) Texas Instruments, Inc. https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 #ifndef _MACH_DAVINCI_CPUIDLE_H
 #define _MACH_DAVINCI_CPUIDLE_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/da830.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/da830.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA830/OMAP L137 chip specific setup
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/clk-provider.h>
 #include <linux/clk/davinci.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/da850.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/da850.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA850/OMAP-L138 chip specific setup
  *
@@ -6,10 +7,7 @@
  * Derived from: arch/arm/mach-davinci/da830.c
  * Original Copyrights follow:
  *
- * 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) MontaVista Software, Inc.
  */
 
 #include <linux/clk-provider.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/dm355.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/dm355.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM355 chip specific setup
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) Deep Root Systems, LLC.
  */
 
 #include <linux/clk-provider.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/dm644x.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/dm644x.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM644x chip specific setup
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) Deep Root Systems, LLC.
  */
 
 #include <linux/clk-provider.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/dm646x.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/dm646x.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM646x chip specific setup
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) Deep Root Systems, LLC.
  */
 
 #include <linux/clk-provider.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/include/mach/common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/include/mach/common.h
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header for code common to all DaVinci machines.
  *
  * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  */
 
 #ifndef __ARCH_ARM_MACH_DAVINCI_COMMON_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/include/mach/cputype.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/include/mach/cputype.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * DaVinci CPU type detection
  *
@@ -8,10 +9,7 @@
  * compiled in to the kernel, the macros return 0 so that
  * resulting code can be optimized out.
  *
- * 2009 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) Deep Root Systems, LLC.
  */
 #ifndef _ASM_ARCH_CPU_H
 #define _ASM_ARCH_CPU_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/include/mach/da8xx.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/include/mach/da8xx.h
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Chip specific defines for DA8XX/OMAP L1XX SoC
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2007, 2009-2010 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007, 2009-2010 (c) MontaVista Software, Inc.
  */
 #ifndef __ASM_ARCH_DAVINCI_DA8XX_H
 #define __ASM_ARCH_DAVINCI_DA8XX_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/include/mach/hardware.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/include/mach/hardware.h
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Hardware definitions common to all DaVinci family processors
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) Deep Root Systems, LLC.
  */
 #ifndef __ASM_ARCH_HARDWARE_H
 #define __ASM_ARCH_HARDWARE_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/include/mach/serial.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/include/mach/serial.h
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * DaVinci serial device definitions
  *
  * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  */
 #ifndef __ASM_ARCH_SERIAL_H
 #define __ASM_ARCH_SERIAL_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/mux.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/mux.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Utility to set the DAVINCI MUX register from a table in mux.h
  *
@@ -8,10 +9,7 @@
  *
  * Written by Tony Lindgren
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  *
  * Copyright (C) 2008 Texas Instruments.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/mux.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/mux.h
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Pin-multiplex helper macros for TI DaVinci family devices
  *
  * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com>
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  *
  * Copyright (C) 2008 Texas Instruments.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/pm.c
@@ -62,7 +62,7 @@
 
 	/* Configure sleep count in deep sleep register */
 	val = __raw_readl(pm_config.deepsleep_reg);
-	val &= ~DEEPSLEEP_SLEEPCOUNT_MASK,
+	val &= ~DEEPSLEEP_SLEEPCOUNT_MASK;
 	val |= pm_config.sleepcount;
 	__raw_writel(val, pm_config.deepsleep_reg);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-davinci/pm_domain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-davinci/pm_domain.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Runtime PM support code for DaVinci
  *
  * Author: Kevin Hilman
  *
  * Copyright (C) 2012 Texas Instruments, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/init.h>
 #include <linux/pm_runtime.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/bridge-regs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/bridge-regs.h
@@ -1,10 +1,5 @@
-/*
- * Mbus-L to Mbus Bridge Registers
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Mbus-L to Mbus Bridge Registers */
 
 #ifndef __ASM_ARCH_BRIDGE_REGS_H
 #define __ASM_ARCH_BRIDGE_REGS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/cm-a510.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/cm-a510.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/cm-a510.c
  *
@@ -5,10 +6,6 @@
  * Konstantin Sinyuk <kostyas@compulab.co.il>
  *
  * Based on Marvell DB-MV88AP510-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/common.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/common.c
  *
  * Core functions for Marvell Dove 88AP510 System On Chip
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk-provider.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/common.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-dove/common.h
  *
  * Core functions for Marvell Dove 88AP510 System On Chip
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ARCH_DOVE_COMMON_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/dove-db-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/dove-db-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/dove-db-setup.c
  *
  * Marvell DB-MV88AP510-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/dove.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/dove.h
@@ -1,10 +1,5 @@
-/*
- * Generic definitions for Marvell Dove 88AP510 SoC
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Generic definitions for Marvell Dove 88AP510 SoC */
 
 #ifndef __ASM_ARCH_DOVE_H
 #define __ASM_ARCH_DOVE_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/irq.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/irq.c
  *
  * Dove IRQ handling.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/init.h>
 #include <linux/irq.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/irqs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/irqs.h
@@ -1,10 +1,5 @@
-/*
- * IRQ definitions for Marvell Dove 88AP510 SoC
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* IRQ definitions for Marvell Dove 88AP510 SoC */
 
 #ifndef __ASM_ARCH_IRQS_H
 #define __ASM_ARCH_IRQS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/mpp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/mpp.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/mpp.c
  *
  * MPP functions for Marvell Dove SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/pcie.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/pcie.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/pcie.c
  *
  * PCIe functions for Marvell Dove 88AP510 SoC
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-dove/pm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-dove/pm.h
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
 
 #ifndef __ASM_ARCH_PM_H
 #define __ASM_ARCH_PM_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-ep93xx/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-ep93xx/core.c
@@ -337,6 +337,7 @@
 				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
 		GPIO_LOOKUP_IDX("G", 0, NULL, 1,
 				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		{ }
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-ep93xx/timer-ep93xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-ep93xx/timer-ep93xx.c
@@ -9,6 +9,7 @@
 #include <linux/io.h>
 #include <asm/mach/time.h>
 #include "soc.h"
+#include "platform.h"
 
 /*************************************************************************
  * Timer handling for EP93xx
@@ -60,7 +61,7 @@
 	return ret;
 }
 
-u64 ep93xx_clocksource_read(struct clocksource *c)
+static u64 ep93xx_clocksource_read(struct clocksource *c)
 {
 	u64 ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-exynos/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-exynos/Kconfig
@@ -18,7 +18,6 @@
 	select EXYNOS_PMU
 	select EXYNOS_SROM
 	select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
-	select GPIOLIB
 	select HAVE_ARM_ARCH_TIMER if ARCH_EXYNOS5
 	select HAVE_ARM_SCU if SMP
 	select HAVE_S3C2410_I2C if I2C
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-exynos/exynos.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-exynos/exynos.c
@@ -149,6 +149,7 @@
 	np = of_find_matching_node(NULL, exynos_dt_pmu_match);
 	if (np)
 		pmu_base_addr = of_iomap(np, 0);
+	of_node_put(np);
 }
 
 static void __init exynos_init_irq(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-hisi/platsmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-hisi/platsmp.c
@@ -67,14 +67,17 @@
 		}
 		ctrl_base = of_iomap(np, 0);
 		if (!ctrl_base) {
+			of_node_put(np);
 			pr_err("failed to map address\n");
 			return;
 		}
 		if (of_property_read_u32(np, "smp-offset", &offset) < 0) {
+			of_node_put(np);
 			pr_err("failed to find smp-offset property\n");
 			return;
 		}
 		ctrl_base += offset;
+		of_node_put(np);
 	}
 }
 
@@ -160,6 +163,7 @@
 	if (WARN_ON(!node))
 		return -1;
 	ctrl_base = of_iomap(node, 0);
+	of_node_put(node);
 
 	/* set the secondary core boot from DDR */
 	remap_reg_value = readl_relaxed(ctrl_base + REG_SC_CTRL);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-imx/cpu-imx25.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-imx/cpu-imx25.c
@@ -23,6 +23,7 @@
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx25-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 	rev = readl(iim_base + MXC_IIMSREV);
 	iounmap(iim_base);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-imx/cpu-imx27.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-imx/cpu-imx27.c
@@ -28,6 +28,7 @@
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
 	ccm_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!ccm_base);
 	/*
 	 * now we have access to the IO registers. As we need
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-imx/cpu-imx31.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-imx/cpu-imx31.c
@@ -39,6 +39,7 @@
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx31-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 
 	/* read SREV register from IIM module */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-imx/cpu-imx35.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-imx/cpu-imx35.c
@@ -21,6 +21,7 @@
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx35-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 
 	rev = imx_readl(iim_base + MXC_IIMSREV);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-imx/cpu-imx5.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-imx/cpu-imx5.c
@@ -28,6 +28,7 @@
 
 	np = of_find_compatible_node(NULL, NULL, compat);
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!iim_base);
 
 	srev = readl(iim_base + IIM_SREV) & 0xff;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-imx/mmdc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-imx/mmdc.c
@@ -99,6 +99,7 @@
 	cpumask_t cpu;
 	struct hrtimer hrtimer;
 	unsigned int active_events;
+	int id;
 	struct device *dev;
 	struct perf_event *mmdc_events[MMDC_NUM_COUNTERS];
 	struct hlist_node node;
@@ -433,8 +434,6 @@
 static int mmdc_pmu_init(struct mmdc_pmu *pmu_mmdc,
 		void __iomem *mmdc_base, struct device *dev)
 {
-	int mmdc_num;
-
 	*pmu_mmdc = (struct mmdc_pmu) {
 		.pmu = (struct pmu) {
 			.task_ctx_nr    = perf_invalid_context,
@@ -452,15 +451,16 @@
 		.active_events = 0,
 	};
 
-	mmdc_num = ida_simple_get(&mmdc_ida, 0, 0, GFP_KERNEL);
+	pmu_mmdc->id = ida_simple_get(&mmdc_ida, 0, 0, GFP_KERNEL);
 
-	return mmdc_num;
+	return pmu_mmdc->id;
 }
 
 static int imx_mmdc_remove(struct platform_device *pdev)
 {
 	struct mmdc_pmu *pmu_mmdc = platform_get_drvdata(pdev);
 
+	ida_simple_remove(&mmdc_ida, pmu_mmdc->id);
 	cpuhp_state_remove_instance_nocalls(cpuhp_mmdc_state, &pmu_mmdc->node);
 	perf_pmu_unregister(&pmu_mmdc->pmu);
 	iounmap(pmu_mmdc->mmdc_base);
@@ -474,7 +474,6 @@
 {
 	struct mmdc_pmu *pmu_mmdc;
 	char *name;
-	int mmdc_num;
 	int ret;
 	const struct of_device_id *of_id =
 		of_match_device(imx_mmdc_dt_ids, &pdev->dev);
@@ -497,14 +496,18 @@
 		cpuhp_mmdc_state = ret;
 	}
 
-	mmdc_num = mmdc_pmu_init(pmu_mmdc, mmdc_base, &pdev->dev);
-	pmu_mmdc->mmdc_ipg_clk = mmdc_ipg_clk;
-	if (mmdc_num == 0)
-		name = "mmdc";
-	else
-		name = devm_kasprintf(&pdev->dev,
-				GFP_KERNEL, "mmdc%d", mmdc_num);
+	ret = mmdc_pmu_init(pmu_mmdc, mmdc_base, &pdev->dev);
+	if (ret < 0)
+		goto  pmu_free;
+
+	name = devm_kasprintf(&pdev->dev,
+				GFP_KERNEL, "mmdc%d", ret);
+	if (!name) {
+		ret = -ENOMEM;
+		goto pmu_release_id;
+	}
 
+	pmu_mmdc->mmdc_ipg_clk = mmdc_ipg_clk;
 	pmu_mmdc->devtype_data = (struct fsl_mmdc_devtype_data *)of_id->data;
 
 	hrtimer_init(&pmu_mmdc->hrtimer, CLOCK_MONOTONIC,
@@ -527,6 +530,8 @@
 	pr_warn("MMDC Perf PMU failed (%d), disabled\n", ret);
 	cpuhp_state_remove_instance_nocalls(cpuhp_mmdc_state, &pmu_mmdc->node);
 	hrtimer_cancel(&pmu_mmdc->hrtimer);
+pmu_release_id:
+	ida_simple_remove(&mmdc_ida, pmu_mmdc->id);
 pmu_free:
 	kfree(pmu_mmdc);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-iop32x/include/mach/entry-macro.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-iop32x/include/mach/entry-macro.S
@@ -20,7 +20,7 @@
 	mrc     p6, 0, \irqstat, c8, c0, 0	@ Read IINTSRC
 	cmp     \irqstat, #0
 	clzne   \irqnr, \irqstat
-	rsbne   \irqnr, \irqnr, #31
+	rsbne   \irqnr, \irqnr, #32
 	.endm
 
 	.macro arch_ret_to_user, tmp1, tmp2
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-iop32x/include/mach/irqs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-iop32x/include/mach/irqs.h
@@ -9,6 +9,6 @@
 #ifndef __IRQS_H
 #define __IRQS_H
 
-#define NR_IRQS			32
+#define NR_IRQS			33
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-iop32x/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-iop32x/irq.c
@@ -32,14 +32,14 @@
 static void
 iop32x_irq_mask(struct irq_data *d)
 {
-	iop32x_mask &= ~(1 << d->irq);
+	iop32x_mask &= ~(1 << (d->irq - 1));
 	intctl_write(iop32x_mask);
 }
 
 static void
 iop32x_irq_unmask(struct irq_data *d)
 {
-	iop32x_mask |= 1 << d->irq;
+	iop32x_mask |= 1 << (d->irq - 1);
 	intctl_write(iop32x_mask);
 }
 
@@ -65,7 +65,7 @@
 	    machine_is_em7210())
 		*IOP3XX_PCIIRSR = 0x0f;
 
-	for (i = 0; i < NR_IRQS; i++) {
+	for (i = 1; i < NR_IRQS; i++) {
 		irq_set_chip_and_handler(i, &ext_chip, handle_level_irq);
 		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-iop32x/irqs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-iop32x/irqs.h
@@ -7,36 +7,40 @@
 #ifndef __IOP32X_IRQS_H
 #define __IOP32X_IRQS_H
 
+/* Interrupts in Linux start at 1, hardware starts at 0 */
+
+#define IOP_IRQ(x) ((x) + 1)
+
 /*
  * IOP80321 chipset interrupts
  */
-#define IRQ_IOP32X_DMA0_EOT	0
-#define IRQ_IOP32X_DMA0_EOC	1
-#define IRQ_IOP32X_DMA1_EOT	2
-#define IRQ_IOP32X_DMA1_EOC	3
-#define IRQ_IOP32X_AA_EOT	6
-#define IRQ_IOP32X_AA_EOC	7
-#define IRQ_IOP32X_CORE_PMON	8
-#define IRQ_IOP32X_TIMER0	9
-#define IRQ_IOP32X_TIMER1	10
-#define IRQ_IOP32X_I2C_0	11
-#define IRQ_IOP32X_I2C_1	12
-#define IRQ_IOP32X_MESSAGING	13
-#define IRQ_IOP32X_ATU_BIST	14
-#define IRQ_IOP32X_PERFMON	15
-#define IRQ_IOP32X_CORE_PMU	16
-#define IRQ_IOP32X_BIU_ERR	17
-#define IRQ_IOP32X_ATU_ERR	18
-#define IRQ_IOP32X_MCU_ERR	19
-#define IRQ_IOP32X_DMA0_ERR	20
-#define IRQ_IOP32X_DMA1_ERR	21
-#define IRQ_IOP32X_AA_ERR	23
-#define IRQ_IOP32X_MSG_ERR	24
-#define IRQ_IOP32X_SSP		25
-#define IRQ_IOP32X_XINT0	27
-#define IRQ_IOP32X_XINT1	28
-#define IRQ_IOP32X_XINT2	29
-#define IRQ_IOP32X_XINT3	30
-#define IRQ_IOP32X_HPI		31
+#define IRQ_IOP32X_DMA0_EOT	IOP_IRQ(0)
+#define IRQ_IOP32X_DMA0_EOC	IOP_IRQ(1)
+#define IRQ_IOP32X_DMA1_EOT	IOP_IRQ(2)
+#define IRQ_IOP32X_DMA1_EOC	IOP_IRQ(3)
+#define IRQ_IOP32X_AA_EOT	IOP_IRQ(6)
+#define IRQ_IOP32X_AA_EOC	IOP_IRQ(7)
+#define IRQ_IOP32X_CORE_PMON	IOP_IRQ(8)
+#define IRQ_IOP32X_TIMER0	IOP_IRQ(9)
+#define IRQ_IOP32X_TIMER1	IOP_IRQ(10)
+#define IRQ_IOP32X_I2C_0	IOP_IRQ(11)
+#define IRQ_IOP32X_I2C_1	IOP_IRQ(12)
+#define IRQ_IOP32X_MESSAGING	IOP_IRQ(13)
+#define IRQ_IOP32X_ATU_BIST	IOP_IRQ(14)
+#define IRQ_IOP32X_PERFMON	IOP_IRQ(15)
+#define IRQ_IOP32X_CORE_PMU	IOP_IRQ(16)
+#define IRQ_IOP32X_BIU_ERR	IOP_IRQ(17)
+#define IRQ_IOP32X_ATU_ERR	IOP_IRQ(18)
+#define IRQ_IOP32X_MCU_ERR	IOP_IRQ(19)
+#define IRQ_IOP32X_DMA0_ERR	IOP_IRQ(20)
+#define IRQ_IOP32X_DMA1_ERR	IOP_IRQ(21)
+#define IRQ_IOP32X_AA_ERR	IOP_IRQ(23)
+#define IRQ_IOP32X_MSG_ERR	IOP_IRQ(24)
+#define IRQ_IOP32X_SSP		IOP_IRQ(25)
+#define IRQ_IOP32X_XINT0	IOP_IRQ(27)
+#define IRQ_IOP32X_XINT1	IOP_IRQ(28)
+#define IRQ_IOP32X_XINT2	IOP_IRQ(29)
+#define IRQ_IOP32X_XINT3	IOP_IRQ(30)
+#define IRQ_IOP32X_HPI		IOP_IRQ(31)
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-lpc18xx/board-dt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-lpc18xx/board-dt.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree board file for NXP LPC18xx/43xx
  *
  * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <asm/mach/arch.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-lpc32xx/pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-lpc32xx/pm.c
@@ -1,13 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-lpc32xx/pm.c
  *
  * Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
  * Modified by Kevin Wells <kevin.wells@nxp.com>
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2005 (c) MontaVista Software, Inc.
  */
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-lpc32xx/suspend.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-lpc32xx/suspend.S
@@ -1,13 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-lpc32xx/suspend.S
  *
  * Original authors: Dmitry Chigirev, Vitaly Wool <source@mvista.com>
  * Modified by Kevin Wells <kevin.wells@nxp.com>
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2005 (c) MontaVista Software, Inc.
  */
 #include <linux/linkage.h>
 #include <asm/assembler.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mediatek/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mediatek/Kconfig
@@ -30,6 +30,7 @@
 config MACH_MT7629
 	bool "MediaTek MT7629 SoCs support"
 	default ARCH_MEDIATEK
+	select HAVE_ARM_ARCH_TIMER
 
 config MACH_MT8127
 	bool "MediaTek MT8127 SoCs support"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-meson/platsmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-meson/platsmp.c
@@ -71,6 +71,7 @@
 	}
 
 	sram_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!sram_base) {
 		pr_err("Couldn't map SRAM registers\n");
 		return;
@@ -91,6 +92,7 @@
 	}
 
 	scu_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!scu_base) {
 		pr_err("Couldn't map SCU registers\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mmp/sram.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mmp/sram.c
@@ -72,6 +72,8 @@
 	if (!info)
 		return -ENOMEM;
 
+	platform_set_drvdata(pdev, info);
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (res == NULL) {
 		dev_err(&pdev->dev, "no memory resource defined\n");
@@ -107,8 +109,6 @@
 	list_add(&info->node, &sram_bank_list);
 	mutex_unlock(&sram_lock);
 
-	platform_set_drvdata(pdev, info);
-
 	dev_info(&pdev->dev, "initialized\n");
 	return 0;
 
@@ -127,17 +127,19 @@
 	struct sram_bank_info *info;
 
 	info = platform_get_drvdata(pdev);
-	if (info == NULL)
-		return -ENODEV;
 
-	mutex_lock(&sram_lock);
-	list_del(&info->node);
-	mutex_unlock(&sram_lock);
+	if (info->sram_size) {
+		mutex_lock(&sram_lock);
+		list_del(&info->node);
+		mutex_unlock(&sram_lock);
+
+		gen_pool_destroy(info->gpool);
+		iounmap(info->sram_virt);
+		kfree(info->pool_name);
+	}
 
-	gen_pool_destroy(info->gpool);
-	iounmap(info->sram_virt);
-	kfree(info->pool_name);
 	kfree(info);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mmp/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mmp/time.c
@@ -43,18 +43,21 @@
 static void __iomem *mmp_timer_base = TIMERS_VIRT_BASE;
 
 /*
- * FIXME: the timer needs some delay to stablize the counter capture
+ * Read the timer through the CVWR register. Delay is required after requesting
+ * a read. The CR register cannot be directly read due to metastability issues
+ * documented in the PXA168 software manual.
  */
 static inline uint32_t timer_read(void)
 {
-	int delay = 100;
+	uint32_t val;
+	int delay = 3;
 
 	__raw_writel(1, mmp_timer_base + TMR_CVWR(1));
 
 	while (delay--)
-		cpu_relax();
+		val = __raw_readl(mmp_timer_base + TMR_CVWR(1));
 
-	return __raw_readl(mmp_timer_base + TMR_CVWR(1));
+	return val;
 }
 
 static u64 notrace mmp_read_sched_clock(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mstar/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mstar/Kconfig
@@ -3,6 +3,7 @@
 	depends on ARCH_MULTI_V7
 	select ARM_GIC
 	select ARM_HEAVY_MB
+	select HAVE_ARM_ARCH_TIMER
 	select MST_IRQ
 	select MSTAR_MSC313_MPLL
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/bridge-regs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/bridge-regs.h
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
 
 #ifndef __ASM_ARCH_BRIDGE_REGS_H
 #define __ASM_ARCH_BRIDGE_REGS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
  *
  * Buffalo WXL (Terastation Duo) Setup routines
  *
  * sebastien requiem <sebastien@requiem.fr>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/common.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/common.c
  *
  * Core functions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/common.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-mv78xx0/common.h
  *
  * Core functions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ARCH_MV78XX0_COMMON_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/db78x00-bp-setup.c
  *
  * Marvell DB-78x00-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/irq.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/irq.c
  *
  * MV78xx0 IRQ handling.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/irqs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/irqs.h
@@ -1,10 +1,5 @@
-/*
- * IRQ definitions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* IRQ definitions for Marvell MV78xx0 SoCs */
 
 #ifndef __ASM_ARCH_IRQS_H
 #define __ASM_ARCH_IRQS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/mpp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/mpp.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78x00/mpp.c
  *
  * MPP functions for Marvell MV78x00 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/mpp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/mpp.h
@@ -1,12 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * linux/arch/arm/mach-mv78xx0/mpp.h -- Multi Purpose Pins
  *
- *
  * sebastien requiem <sebastien@requiem.fr>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MV78X00_MPP_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/mv78xx0.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/mv78xx0.h
@@ -1,10 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Generic definitions for Marvell MV78xx0 SoC flavors:
  *  MV781x0 and MV782x0.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARCH_MV78XX0_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/pcie.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/pcie.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/pcie.c
  *
  * PCIe functions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78x00/rd78x00-masa-setup.c
  *
  * Marvell RD-78x00-mASA Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/armada-370-xp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/armada-370-xp.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Generic definitions for Marvell Armada_370_XP SoCs
  *
@@ -6,10 +7,6 @@
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_ARMADA_370_XP_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/board-v7.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/board-v7.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree support for Armada 370 and XP platforms.
  *
@@ -6,10 +7,6 @@
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/coherency.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/coherency.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Coherency fabric (Aurora) support for Armada 370, 375, 38x and XP
  * platforms.
@@ -8,10 +9,6 @@
  * Gregory Clement <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada 370, 375, 38x and XP SOCs have a coherency fabric which is
  * responsible for ensuring hardware coherency between all CPUs and between
  * CPUs and I/O masters. This file initializes the coherency fabric and
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/coherency.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/coherency.h
@@ -1,14 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-mvebu/include/mach/coherency.h
  *
- *
  * Coherency fabric (Aurora) support for Armada 370 and XP platforms.
  *
  * Copyright (C) 2012 Marvell
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_370_XP_COHERENCY_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/coherency_ll.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/coherency_ll.S
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Coherency fabric: low level functions
  *
@@ -5,10 +6,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * This file implements the assembly function to add a CPU to the
  * coherency fabric. This function is called by each of the secondary
  * CPUs during their early boot in an SMP kernel, this why this
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/common.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Core functions for Marvell System On Chip
  *
@@ -6,10 +7,6 @@
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ARCH_MVEBU_COMMON_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/cpu-reset.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/cpu-reset.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "mvebu-cpureset: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/dove.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/dove.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mvebu/dove.c
  *
  * Marvell Dove 88AP510 System On Chip FDT Board
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/headsmp-a9.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/headsmp-a9.S
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SMP support: Entry point for secondary CPUs of Marvell EBU
  * Cortex-A9 based SOCs (Armada 375 and Armada 38x).
@@ -6,10 +7,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/linkage.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/headsmp.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/headsmp.S
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SMP support: Entry point for secondary CPUs
  *
@@ -7,10 +8,6 @@
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * This file implements the assembly entry point for secondary CPUs in
  * an SMP kernel. The only thing we need to do is to add the CPU to
  * the coherency fabric by writing to 2 registers. Currently the base
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/kirkwood.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/kirkwood.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
  *
  * arch/arm/mach-mvebu/kirkwood.c
  *
  * Flattened Device Tree board initialization
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/kirkwood.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/kirkwood.h
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-mvebu/kirkwood.h
  *
  * Generic definitions for Marvell Kirkwood SoC flavors:
  * 88F6180, 88F6192 and 88F6281.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define KIRKWOOD_REGS_PHYS_BASE	0xf1000000
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/mvebu-soc-id.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/mvebu-soc-id.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * ID and revision information for mvebu SoCs
  *
@@ -5,10 +6,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * All the mvebu SoCs have information related to their variant and
  * revision that can be read from the PCI control register. This is
  * done before the PCI initialization to avoid any conflict. Once the
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/mvebu-soc-id.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/mvebu-soc-id.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Marvell EBU SoC ID and revision definitions.
  *
  * Copyright (C) 2014 Marvell Semiconductor
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __LINUX_MVEBU_SOC_ID_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/platsmp-a9.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/platsmp-a9.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Symmetric Multi Processing (SMP) support for Marvell EBU Cortex-A9
  * based SOCs (Armada 375/38x).
@@ -6,10 +7,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/platsmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/platsmp.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Symmetric Multi Processing (SMP) support for Armada XP
  *
@@ -8,10 +9,6 @@
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada XP SoC has 4 ARMv7 PJ4B CPUs running in full HW coherency
  * This file implements the routines for preparing the SMP infrastructure
  * and waking up the secondary CPUs
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/pm-board.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/pm-board.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Board-level suspend/resume support.
  *
  * Copyright (C) 2014-2015 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/delay.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/pm.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Suspend/resume support. Currently supporting Armada XP only.
  *
  * Copyright (C) 2014 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/cpu_pm.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/pmsu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/pmsu.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Power Management Service Unit(PMSU) support for Armada 370/XP platforms.
  *
@@ -7,10 +8,6 @@
  * Gregory Clement <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada 370 and Armada XP SOCs have a power management service
  * unit which is responsible for powering down and waking up CPUs and
  * other SOC units
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/pmsu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/pmsu.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Power Management Service Unit (PMSU) support for Armada 370/XP platforms.
  *
  * Copyright (C) 2012 Marvell
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_MVEBU_PMSU_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/pmsu_ll.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/pmsu_ll.S
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Copyright (C) 2014 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Gregory Clement <gregory.clement@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/linkage.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mvebu/system-controller.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mvebu/system-controller.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * System controller support for Armada 370, 375 and XP platforms.
  *
@@ -7,10 +8,6 @@
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada 370, 375 and Armada XP SoCs have a range of
  * miscellaneous registers, that do not belong to a particular device,
  * but rather provide system-level features. This basic
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-mxs/mach-mxs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-mxs/mach-mxs.c
@@ -393,8 +393,10 @@
 
 	root = of_find_node_by_path("/");
 	ret = of_property_read_string(root, "model", &soc_dev_attr->machine);
-	if (ret)
+	if (ret) {
+		kfree(soc_dev_attr);
 		return;
+	}
 
 	soc_dev_attr->family = "Freescale MXS Family";
 	soc_dev_attr->soc_id = mxs_get_soc_id();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap1/clock.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap1/clock.c
@@ -41,7 +41,7 @@
 unsigned long omap1_uart_recalc(struct clk *clk)
 {
 	unsigned int val = __raw_readl(clk->enable_reg);
-	return val & clk->enable_bit ? 48000000 : 12000000;
+	return val & 1 << clk->enable_bit ? 48000000 : 12000000;
 }
 
 unsigned long omap1_sossi_recalc(struct clk *clk)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap1/include/mach/mtd-xip.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap1/include/mach/mtd-xip.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * MTD primitives for XIP support. Architecture specific functions.
  *
@@ -5,10 +6,7 @@
  *
  * Author: Vladimir Barinov <vbarinov@embeddedalley.com>
  *
- * (c) 2005 MontaVista Software, Inc.  This file is licensed under the
- * terms of the GNU General Public License version 2.  This program is
- * licensed "as is" without any warranty of any kind, whether express or
- * implied.
+ * (c) 2005 MontaVista Software, Inc.
  */
 
 #ifndef __ARCH_OMAP_MTD_XIP_H__
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap1/pm_bus.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap1/pm_bus.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Runtime PM support code for OMAP1
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
  * Copyright (C) 2010 Texas Instruments, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/init.h>
 #include <linux/kernel.h>
@@ -43,4 +40,3 @@
 	return 0;
 }
 core_initcall(omap1_pm_runtime_init);
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap1/timer.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap1/timer.c
@@ -165,7 +165,7 @@
 	kfree(pdata);
 
 err_free_pdev:
-	platform_device_unregister(pdev);
+	platform_device_put(pdev);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/board-generic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/board-generic.c
@@ -13,6 +13,7 @@
 #include <linux/of_platform.h>
 #include <linux/irqdomain.h>
 #include <linux/clocksource.h>
+#include <linux/clockchips.h>
 
 #include <asm/setup.h>
 #include <asm/mach/arch.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/display.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/display.c
@@ -211,6 +211,7 @@
 	node = of_find_node_by_name(NULL, "omap4_padconf_global");
 	if (node)
 		omap4_dsi_mux_syscon = syscon_node_to_regmap(node);
+	of_node_put(node);
 
 	return 0;
 }
@@ -259,13 +260,15 @@
 
 	if (!pdev) {
 		pr_err("Unable to find DSS platform device\n");
+		of_node_put(node);
 		return -ENODEV;
 	}
 
 	r = of_platform_populate(node, NULL, NULL, &pdev->dev);
+	put_device(&pdev->dev);
+	of_node_put(node);
 	if (r) {
 		pr_err("Unable to populate DSS submodule devices\n");
-		put_device(&pdev->dev);
 		return r;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/id.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/id.c
@@ -793,11 +793,16 @@
 
 	soc_dev_attr->machine  = soc_name;
 	soc_dev_attr->family   = omap_get_family();
+	if (!soc_dev_attr->family) {
+		kfree(soc_dev_attr);
+		return;
+	}
 	soc_dev_attr->revision = soc_rev;
 	soc_dev_attr->custom_attr_group = omap_soc_groups[0];
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev)) {
+		kfree(soc_dev_attr->family);
 		kfree(soc_dev_attr);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/omap4-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/omap4-common.c
@@ -314,10 +314,12 @@
 
 	np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-gic");
 	gic_dist_base_addr = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!gic_dist_base_addr);
 
 	np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-twd-timer");
 	twd_base = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!twd_base);
 
 skip_errata_init:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/omap_hwmod.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/omap_hwmod.c
@@ -752,8 +752,10 @@
 
 	for_each_matching_node(np, ti_clkctrl_match_table) {
 		ret = _setup_clkctrl_provider(np);
-		if (ret)
+		if (ret) {
+			of_node_put(np);
 			break;
+		}
 	}
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/pdata-quirks.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/pdata-quirks.c
@@ -587,6 +587,8 @@
 
 		of_platform_populate(np, omap_dt_match_table,
 				     omap_auxdata_lookup, NULL);
+
+		of_node_put(np);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/powerdomain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/powerdomain.c
@@ -174,7 +174,7 @@
 		break;
 	case PWRDM_STATE_PREV:
 		prev = pwrdm_read_prev_pwrst(pwrdm);
-		if (pwrdm->state != prev)
+		if (prev >= 0 && pwrdm->state != prev)
 			pwrdm->state_counter[prev]++;
 		if (prev == PWRDM_POWER_RET)
 			_update_logic_membank_counters(pwrdm);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/prcm43xx.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/prcm43xx.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AM43x PRCM defines
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_PRCM_43XX_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/prm3xxx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/prm3xxx.c
@@ -708,6 +708,7 @@
 	}
 
 	irq_num = of_irq_get(np, 0);
+	of_node_put(np);
 	if (irq_num == -EPROBE_DEFER)
 		return irq_num;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/timer.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/timer.c
@@ -76,6 +76,7 @@
 	}
 
 	rate = clk_get_rate(sys_clk);
+	clk_put(sys_clk);
 
 	if (soc_is_dra7xx()) {
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-omap2/vc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-omap2/vc.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP Voltage Controller (VC) interface
  *
  * Copyright (C) 2011 Texas Instruments, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/delay.h>
@@ -895,4 +892,3 @@
 	else if (cpu_is_omap44xx())
 		omap4_vc_init_channel(voltdm);
 }
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/board-d2net.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/board-d2net.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/board-d2net.c
  *
  * LaCie d2Network and Big Disk Network NAS setup
  *
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/board-dt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/board-dt.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright 2012 (C), Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
  * arch/arm/mach-orion5x/board-dt.c
  *
  * Flattened Device Tree board initialization
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
@@ -63,6 +60,9 @@
 	if (of_machine_is_compatible("maxtor,shared-storage-2"))
 		mss2_init();
 
+	if (of_machine_is_compatible("lacie,d2-network"))
+		d2net_init();
+
 	of_platform_default_populate(NULL, orion5x_auxdata_lookup, NULL);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/board-rd88f5182.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/board-rd88f5182.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5182-setup.c
  *
  * Marvell Orion-NAS Reference Design Setup
  *
  * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/bridge-regs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/bridge-regs.h
@@ -1,10 +1,5 @@
-/*
- * Orion CPU Bridge Registers
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Orion CPU Bridge Registers */
 
 #ifndef __ASM_ARCH_BRIDGE_REGS_H
 #define __ASM_ARCH_BRIDGE_REGS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/common.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/common.c
  *
  * Core functions for Marvell Orion 5x SoCs
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/common.h
@@ -75,6 +75,12 @@
 static inline void mss2_init(void) {}
 #endif
 
+#ifdef CONFIG_MACH_D2NET_DT
+void d2net_init(void);
+#else
+static inline void d2net_init(void) {}
+#endif
+
 /*****************************************************************************
  * Helpers to access Orion registers
  ****************************************************************************/
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/db88f5281-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/db88f5281-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/db88f5281-setup.c
  *
  * Marvell Orion-2 Development Board Setup
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/irq.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/irq.c
  *
  * Core IRQ functions for Marvell Orion System On Chip
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/irqs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/irqs.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * IRQ definitions for Orion SoC
  *
  *  Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- *  This file is licensed under the terms of the GNU General Public
- *  License version 2. This program is licensed "as is" without any
- *  warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARCH_IRQS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/kurobox_pro-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/kurobox_pro-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/kurobox_pro-setup.c
  *
  * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/ls_hgl-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/ls_hgl-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/ls_hgl-setup.c
  *
  * Maintainer: Zhu Qingsen <zhuqs@cn.fujitsu.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/mpp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/mpp.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/mpp.c
  *
  * MPP functions for Marvell Orion 5x SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/net2big-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/net2big-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/net2big-setup.c
  *
  * LaCie 2Big Network NAS setup
  *
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
@@ -432,4 +429,3 @@
 	.fixup		= tag_fixup_mem32,
 	.restart	= orion5x_restart,
 MACHINE_END
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/orion5x.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/orion5x.h
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Generic definitions of Orion SoC flavors:
  *  Orion-1, Orion-VoIP, Orion-NAS, Orion-2, and Orion-1-90.
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARCH_ORION5X_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/pci.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/pci.c
  *
  * PCI and PCIe functions for Marvell Orion System On Chip
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
  *
  * Marvell Orion-VoIP FXO Reference Design Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
  *
  * Marvell Orion-VoIP GE Reference Design Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/rd88f5182-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/rd88f5182-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5182-setup.c
  *
  * Marvell Orion-NAS Reference Design Setup
  *
  * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f6183-ap-ge-setup.c
  *
  * Marvell Orion-1-90 AP GE Reference Design Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/ts78xx-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/ts78xx-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/ts78xx-setup.c
  *
  * Maintainer: Alexander Clouter <alex@digriz.org.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/wnr854t-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -1,10 +1,5 @@
-/*
- * arch/arm/mach-orion5x/wnr854t-setup.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// arch/arm/mach-orion5x/wnr854t-setup.c
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -1,10 +1,5 @@
-/*
- * arch/arm/mach-orion5x/wrt350n-v2-setup.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// arch/arm/mach-orion5x/wrt350n-v2-setup.c
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/cm-x300.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/cm-x300.c
@@ -354,13 +354,13 @@
 static struct gpiod_lookup_table cm_x300_spi_gpiod_table = {
 	.dev_id         = "spi_gpio",
 	.table          = {
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_SCL,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_SCL - GPIO_LCD_BASE,
 			    "sck", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_DIN,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_DIN - GPIO_LCD_BASE,
 			    "mosi", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_DOUT,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_DOUT - GPIO_LCD_BASE,
 			    "miso", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_CS,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_CS - GPIO_LCD_BASE,
 			    "cs", GPIO_ACTIVE_HIGH),
 		{ },
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/eseries.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/eseries.c
@@ -1,13 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Hardware definitions for the Toshiba eseries PDAs
  *
  * Copyright (c) 2003 Ian Molton <spyro@f2s.com>
- *
- * This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- *
  */
 
 #include <linux/clkdev.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/magician.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/magician.c
@@ -681,7 +681,7 @@
 static struct gpiod_lookup_table bq24022_gpiod_table = {
 	.dev_id = "gpio-regulator",
 	.table = {
-		GPIO_LOOKUP("gpio-pxa", EGPIO_MAGICIAN_BQ24022_ISET2,
+		GPIO_LOOKUP("htc-egpio-0", EGPIO_MAGICIAN_BQ24022_ISET2 - MAGICIAN_EGPIO_BASE,
 			    NULL, GPIO_ACTIVE_HIGH),
 		GPIO_LOOKUP("gpio-pxa", GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
 			    "enable", GPIO_ACTIVE_LOW),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/sharpsl_pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/sharpsl_pm.c
@@ -220,8 +220,6 @@
 {
 	schedule_delayed_work(&sharpsl_bat, msecs_to_jiffies(125));
 }
-EXPORT_SYMBOL(sharpsl_battery_kick);
-
 
 static void sharpsl_battery_thread(struct work_struct *private_)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/spitz.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/spitz.c
@@ -9,7 +9,6 @@
  */
 
 #include <linux/kernel.h>
-#include <linux/module.h>	/* symbol_get ; symbol_put */
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/gpio_keys.h>
@@ -44,7 +43,7 @@
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/video-pxafb.h>
-#include <mach/spitz.h>
+#include "spitz.h"
 #include "sharpsl_pm.h"
 #include <mach/smemc.h>
 
@@ -514,24 +513,11 @@
 	.gpio_cs		= SPITZ_GPIO_ADS7846_CS,
 };
 
-static void spitz_bl_kick_battery(void)
-{
-	void (*kick_batt)(void);
-
-	kick_batt = symbol_get(sharpsl_battery_kick);
-	if (kick_batt) {
-		kick_batt();
-		symbol_put(sharpsl_battery_kick);
-	}
-}
-
 static struct gpiod_lookup_table spitz_lcdcon_gpio_table = {
 	.dev_id = "spi2.1",
 	.table = {
-		GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_BACKLIGHT_CONT,
-			    "BL_CONT", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_BACKLIGHT_ON,
-			    "BL_ON", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.1", 6, "BL_CONT", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("sharp-scoop.1", 7, "BL_ON", GPIO_ACTIVE_HIGH),
 		{ },
 	},
 };
@@ -539,10 +525,8 @@
 static struct gpiod_lookup_table akita_lcdcon_gpio_table = {
 	.dev_id = "spi2.1",
 	.table = {
-		GPIO_LOOKUP("gpio-pxa", AKITA_GPIO_BACKLIGHT_CONT,
-			    "BL_CONT", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("gpio-pxa", AKITA_GPIO_BACKLIGHT_ON,
-			    "BL_ON", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("i2c-max7310", 3, "BL_ON", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("i2c-max7310", 4, "BL_CONT", GPIO_ACTIVE_LOW),
 		{ },
 	},
 };
@@ -552,7 +536,7 @@
 	.max_intensity		= 0x2f,
 	.default_intensity	= 0x1f,
 	.limit_mask		= 0x0b,
-	.kick_battery		= spitz_bl_kick_battery,
+	.kick_battery		= sharpsl_battery_kick,
 };
 
 static struct pxa2xx_spi_chip spitz_lcdcon_chip = {
@@ -966,11 +950,36 @@
 static inline void spitz_i2c_init(void) {}
 #endif
 
+static struct gpiod_lookup_table spitz_audio_gpio_table = {
+	.dev_id = "spitz-audio",
+	.table = {
+		GPIO_LOOKUP("sharp-scoop.0", 3, "mute-l", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.0", 4, "mute-r", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.1", 8, "mic", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table akita_audio_gpio_table = {
+	.dev_id = "spitz-audio",
+	.table = {
+		GPIO_LOOKUP("sharp-scoop.0", 3, "mute-l", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.0", 4, "mute-r", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("i2c-max7310", 2, "mic", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /******************************************************************************
  * Audio devices
  ******************************************************************************/
 static inline void spitz_audio_init(void)
 {
+	if (machine_is_akita())
+		gpiod_add_lookup_table(&akita_audio_gpio_table);
+	else
+		gpiod_add_lookup_table(&spitz_audio_gpio_table);
+
 	platform_device_register_simple("spitz-audio", -1, NULL, 0);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/spitz.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/spitz.h
@@ -0,0 +1,185 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Hardware specific definitions for SL-Cx000 series of PDAs
+ *
+ * Copyright (c) 2005 Alexander Wykes
+ * Copyright (c) 2005 Richard Purdie
+ *
+ * Based on Sharp's 2.4 kernel patches
+ */
+#ifndef __ASM_ARCH_SPITZ_H
+#define __ASM_ARCH_SPITZ_H  1
+#endif
+
+#include <mach/irqs.h> /* PXA_NR_BUILTIN_GPIO, PXA_GPIO_TO_IRQ */
+#include <linux/fb.h>
+
+/* Spitz/Akita GPIOs */
+
+#define SPITZ_GPIO_KEY_INT         (0) /* Key Interrupt */
+#define SPITZ_GPIO_RESET           (1)
+#define SPITZ_GPIO_nSD_DETECT      (9)
+#define SPITZ_GPIO_TP_INT          (11) /* Touch Panel interrupt */
+#define SPITZ_GPIO_AK_INT          (13) /* Remote Control */
+#define SPITZ_GPIO_ADS7846_CS      (14)
+#define SPITZ_GPIO_SYNC            (16)
+#define SPITZ_GPIO_MAX1111_CS      (20)
+#define SPITZ_GPIO_FATAL_BAT       (21)
+#define SPITZ_GPIO_HSYNC           (22)
+#define SPITZ_GPIO_nSD_CLK         (32)
+#define SPITZ_GPIO_USB_DEVICE      (35)
+#define SPITZ_GPIO_USB_HOST        (37)
+#define SPITZ_GPIO_USB_CONNECT     (41)
+#define SPITZ_GPIO_LCDCON_CS       (53)
+#define SPITZ_GPIO_nPCE            (54)
+#define SPITZ_GPIO_nSD_WP          (81)
+#define SPITZ_GPIO_ON_RESET        (89)
+#define SPITZ_GPIO_BAT_COVER       (90)
+#define SPITZ_GPIO_CF_CD           (94)
+#define SPITZ_GPIO_ON_KEY          (95)
+#define SPITZ_GPIO_SWA             (97)
+#define SPITZ_GPIO_SWB             (96)
+#define SPITZ_GPIO_CHRG_FULL       (101)
+#define SPITZ_GPIO_CO              (101)
+#define SPITZ_GPIO_CF_IRQ          (105)
+#define SPITZ_GPIO_AC_IN           (115)
+#define SPITZ_GPIO_HP_IN           (116)
+
+/* Spitz Only GPIOs */
+
+#define SPITZ_GPIO_CF2_IRQ         (106) /* CF slot1 Ready */
+#define SPITZ_GPIO_CF2_CD          (93)
+
+
+/* Spitz/Akita Keyboard Definitions */
+
+#define SPITZ_KEY_STROBE_NUM         (11)
+#define SPITZ_KEY_SENSE_NUM          (7)
+#define SPITZ_GPIO_G0_STROBE_BIT     0x0f800000
+#define SPITZ_GPIO_G1_STROBE_BIT     0x00100000
+#define SPITZ_GPIO_G2_STROBE_BIT     0x01000000
+#define SPITZ_GPIO_G3_STROBE_BIT     0x00041880
+#define SPITZ_GPIO_G0_SENSE_BIT      0x00021000
+#define SPITZ_GPIO_G1_SENSE_BIT      0x000000d4
+#define SPITZ_GPIO_G2_SENSE_BIT      0x08000000
+#define SPITZ_GPIO_G3_SENSE_BIT      0x00000000
+
+#define SPITZ_GPIO_KEY_STROBE0       88
+#define SPITZ_GPIO_KEY_STROBE1       23
+#define SPITZ_GPIO_KEY_STROBE2       24
+#define SPITZ_GPIO_KEY_STROBE3       25
+#define SPITZ_GPIO_KEY_STROBE4       26
+#define SPITZ_GPIO_KEY_STROBE5       27
+#define SPITZ_GPIO_KEY_STROBE6       52
+#define SPITZ_GPIO_KEY_STROBE7       103
+#define SPITZ_GPIO_KEY_STROBE8       107
+#define SPITZ_GPIO_KEY_STROBE9       108
+#define SPITZ_GPIO_KEY_STROBE10      114
+
+#define SPITZ_GPIO_KEY_SENSE0        12
+#define SPITZ_GPIO_KEY_SENSE1        17
+#define SPITZ_GPIO_KEY_SENSE2        91
+#define SPITZ_GPIO_KEY_SENSE3        34
+#define SPITZ_GPIO_KEY_SENSE4        36
+#define SPITZ_GPIO_KEY_SENSE5        38
+#define SPITZ_GPIO_KEY_SENSE6        39
+
+
+/* Spitz Scoop Device (No. 1) GPIOs */
+/* Suspend States in comments */
+#define SPITZ_SCP_LED_GREEN     SCOOP_GPCR_PA11  /* Keep */
+#define SPITZ_SCP_JK_B          SCOOP_GPCR_PA12  /* Keep */
+#define SPITZ_SCP_CHRG_ON       SCOOP_GPCR_PA13  /* Keep */
+#define SPITZ_SCP_MUTE_L        SCOOP_GPCR_PA14  /* Low */
+#define SPITZ_SCP_MUTE_R        SCOOP_GPCR_PA15  /* Low */
+#define SPITZ_SCP_CF_POWER      SCOOP_GPCR_PA16  /* Keep */
+#define SPITZ_SCP_LED_ORANGE    SCOOP_GPCR_PA17  /* Keep */
+#define SPITZ_SCP_JK_A          SCOOP_GPCR_PA18  /* Low */
+#define SPITZ_SCP_ADC_TEMP_ON   SCOOP_GPCR_PA19  /* Low */
+
+#define SPITZ_SCP_IO_DIR      (SPITZ_SCP_JK_B | SPITZ_SCP_CHRG_ON | \
+                               SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R | \
+                               SPITZ_SCP_CF_POWER | SPITZ_SCP_JK_A | SPITZ_SCP_ADC_TEMP_ON)
+#define SPITZ_SCP_IO_OUT      (SPITZ_SCP_CHRG_ON | SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R)
+#define SPITZ_SCP_SUS_CLR     (SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R | SPITZ_SCP_JK_A | SPITZ_SCP_ADC_TEMP_ON)
+#define SPITZ_SCP_SUS_SET     0
+
+#define SPITZ_SCP_GPIO_BASE	(PXA_NR_BUILTIN_GPIO)
+#define SPITZ_GPIO_LED_GREEN	(SPITZ_SCP_GPIO_BASE + 0)
+#define SPITZ_GPIO_JK_B		(SPITZ_SCP_GPIO_BASE + 1)
+#define SPITZ_GPIO_CHRG_ON	(SPITZ_SCP_GPIO_BASE + 2)
+#define SPITZ_GPIO_MUTE_L	(SPITZ_SCP_GPIO_BASE + 3)
+#define SPITZ_GPIO_MUTE_R	(SPITZ_SCP_GPIO_BASE + 4)
+#define SPITZ_GPIO_CF_POWER	(SPITZ_SCP_GPIO_BASE + 5)
+#define SPITZ_GPIO_LED_ORANGE	(SPITZ_SCP_GPIO_BASE + 6)
+#define SPITZ_GPIO_JK_A		(SPITZ_SCP_GPIO_BASE + 7)
+#define SPITZ_GPIO_ADC_TEMP_ON	(SPITZ_SCP_GPIO_BASE + 8)
+
+/* Spitz Scoop Device (No. 2) GPIOs */
+/* Suspend States in comments */
+#define SPITZ_SCP2_IR_ON           SCOOP_GPCR_PA11  /* High */
+#define SPITZ_SCP2_AKIN_PULLUP     SCOOP_GPCR_PA12  /* Keep */
+#define SPITZ_SCP2_RESERVED_1      SCOOP_GPCR_PA13  /* High */
+#define SPITZ_SCP2_RESERVED_2      SCOOP_GPCR_PA14  /* Low */
+#define SPITZ_SCP2_RESERVED_3      SCOOP_GPCR_PA15  /* Low */
+#define SPITZ_SCP2_RESERVED_4      SCOOP_GPCR_PA16  /* Low */
+#define SPITZ_SCP2_BACKLIGHT_CONT  SCOOP_GPCR_PA17  /* Low */
+#define SPITZ_SCP2_BACKLIGHT_ON    SCOOP_GPCR_PA18  /* Low */
+#define SPITZ_SCP2_MIC_BIAS        SCOOP_GPCR_PA19  /* Low */
+
+#define SPITZ_SCP2_IO_DIR (SPITZ_SCP2_AKIN_PULLUP | SPITZ_SCP2_RESERVED_1 | \
+                           SPITZ_SCP2_RESERVED_2 | SPITZ_SCP2_RESERVED_3 | SPITZ_SCP2_RESERVED_4 | \
+                           SPITZ_SCP2_BACKLIGHT_CONT | SPITZ_SCP2_BACKLIGHT_ON | SPITZ_SCP2_MIC_BIAS)
+
+#define SPITZ_SCP2_IO_OUT   (SPITZ_SCP2_AKIN_PULLUP | SPITZ_SCP2_RESERVED_1)
+#define SPITZ_SCP2_SUS_CLR  (SPITZ_SCP2_RESERVED_2 | SPITZ_SCP2_RESERVED_3 | SPITZ_SCP2_RESERVED_4 | \
+                             SPITZ_SCP2_BACKLIGHT_CONT | SPITZ_SCP2_BACKLIGHT_ON | SPITZ_SCP2_MIC_BIAS)
+#define SPITZ_SCP2_SUS_SET  (SPITZ_SCP2_IR_ON | SPITZ_SCP2_RESERVED_1)
+
+#define SPITZ_SCP2_GPIO_BASE		(PXA_NR_BUILTIN_GPIO + 12)
+#define SPITZ_GPIO_IR_ON		(SPITZ_SCP2_GPIO_BASE + 0)
+#define SPITZ_GPIO_AKIN_PULLUP		(SPITZ_SCP2_GPIO_BASE + 1)
+#define SPITZ_GPIO_RESERVED_1		(SPITZ_SCP2_GPIO_BASE + 2)
+#define SPITZ_GPIO_RESERVED_2		(SPITZ_SCP2_GPIO_BASE + 3)
+#define SPITZ_GPIO_RESERVED_3		(SPITZ_SCP2_GPIO_BASE + 4)
+#define SPITZ_GPIO_RESERVED_4		(SPITZ_SCP2_GPIO_BASE + 5)
+#define SPITZ_GPIO_BACKLIGHT_CONT	(SPITZ_SCP2_GPIO_BASE + 6)
+#define SPITZ_GPIO_BACKLIGHT_ON		(SPITZ_SCP2_GPIO_BASE + 7)
+#define SPITZ_GPIO_MIC_BIAS		(SPITZ_SCP2_GPIO_BASE + 8)
+
+/* Akita IO Expander GPIOs */
+#define AKITA_IOEXP_GPIO_BASE		(PXA_NR_BUILTIN_GPIO + 12)
+#define AKITA_GPIO_RESERVED_0		(AKITA_IOEXP_GPIO_BASE + 0)
+#define AKITA_GPIO_RESERVED_1		(AKITA_IOEXP_GPIO_BASE + 1)
+#define AKITA_GPIO_MIC_BIAS		(AKITA_IOEXP_GPIO_BASE + 2)
+#define AKITA_GPIO_BACKLIGHT_ON		(AKITA_IOEXP_GPIO_BASE + 3)
+#define AKITA_GPIO_BACKLIGHT_CONT	(AKITA_IOEXP_GPIO_BASE + 4)
+#define AKITA_GPIO_AKIN_PULLUP		(AKITA_IOEXP_GPIO_BASE + 5)
+#define AKITA_GPIO_IR_ON		(AKITA_IOEXP_GPIO_BASE + 6)
+#define AKITA_GPIO_RESERVED_7		(AKITA_IOEXP_GPIO_BASE + 7)
+
+/* Spitz IRQ Definitions */
+
+#define SPITZ_IRQ_GPIO_KEY_INT        PXA_GPIO_TO_IRQ(SPITZ_GPIO_KEY_INT)
+#define SPITZ_IRQ_GPIO_AC_IN          PXA_GPIO_TO_IRQ(SPITZ_GPIO_AC_IN)
+#define SPITZ_IRQ_GPIO_AK_INT         PXA_GPIO_TO_IRQ(SPITZ_GPIO_AK_INT)
+#define SPITZ_IRQ_GPIO_HP_IN          PXA_GPIO_TO_IRQ(SPITZ_GPIO_HP_IN)
+#define SPITZ_IRQ_GPIO_TP_INT         PXA_GPIO_TO_IRQ(SPITZ_GPIO_TP_INT)
+#define SPITZ_IRQ_GPIO_SYNC           PXA_GPIO_TO_IRQ(SPITZ_GPIO_SYNC)
+#define SPITZ_IRQ_GPIO_ON_KEY         PXA_GPIO_TO_IRQ(SPITZ_GPIO_ON_KEY)
+#define SPITZ_IRQ_GPIO_SWA            PXA_GPIO_TO_IRQ(SPITZ_GPIO_SWA)
+#define SPITZ_IRQ_GPIO_SWB            PXA_GPIO_TO_IRQ(SPITZ_GPIO_SWB)
+#define SPITZ_IRQ_GPIO_BAT_COVER      PXA_GPIO_TO_IRQ(SPITZ_GPIO_BAT_COVER)
+#define SPITZ_IRQ_GPIO_FATAL_BAT      PXA_GPIO_TO_IRQ(SPITZ_GPIO_FATAL_BAT)
+#define SPITZ_IRQ_GPIO_CO             PXA_GPIO_TO_IRQ(SPITZ_GPIO_CO)
+#define SPITZ_IRQ_GPIO_CF_IRQ         PXA_GPIO_TO_IRQ(SPITZ_GPIO_CF_IRQ)
+#define SPITZ_IRQ_GPIO_CF_CD          PXA_GPIO_TO_IRQ(SPITZ_GPIO_CF_CD)
+#define SPITZ_IRQ_GPIO_CF2_IRQ        PXA_GPIO_TO_IRQ(SPITZ_GPIO_CF2_IRQ)
+#define SPITZ_IRQ_GPIO_nSD_INT        PXA_GPIO_TO_IRQ(SPITZ_GPIO_nSD_INT)
+#define SPITZ_IRQ_GPIO_nSD_DETECT     PXA_GPIO_TO_IRQ(SPITZ_GPIO_nSD_DETECT)
+
+/*
+ * Shared data structures
+ */
+extern struct platform_device spitzssp_device;
+extern struct sharpsl_charger_machinfo spitz_pm_machinfo;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/spitz_pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/spitz_pm.c
@@ -20,7 +20,7 @@
 #include <asm/mach-types.h>
 #include <mach/hardware.h>
 
-#include <mach/spitz.h>
+#include "spitz.h"
 #include "pxa27x.h"
 #include "sharpsl_pm.h"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/standby.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/standby.S
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * PXA27x standby mode
  *
  * Author: David Burrage
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2005 (c) MontaVista Software, Inc.
  */
 
 #include <linux/linkage.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-pxa/tosa.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-pxa/tosa.c
@@ -296,9 +296,9 @@
 	.table = {
 		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_nSD_DETECT,
 			    "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_SD_WP,
+		GPIO_LOOKUP("sharp-scoop.0", TOSA_GPIO_SD_WP - TOSA_SCOOP_GPIO_BASE,
 			    "wp", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_PWR_ON,
+		GPIO_LOOKUP("sharp-scoop.0", TOSA_GPIO_PWR_ON - TOSA_SCOOP_GPIO_BASE,
 			    "power", GPIO_ACTIVE_HIGH),
 		{ },
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-realview/platsmp-dt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-realview/platsmp-dt.c
@@ -66,6 +66,7 @@
 		return;
 	}
 	map = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (IS_ERR(map)) {
 		pr_err("PLATSMP: No syscon regmap\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-s3c/irq-s3c24xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-s3c/irq-s3c24xx.c
@@ -361,11 +361,25 @@
 static asmlinkage void __exception_irq_entry s3c24xx_handle_irq(struct pt_regs *regs)
 {
 	do {
-		if (likely(s3c_intc[0]))
-			if (s3c24xx_handle_intc(s3c_intc[0], regs, 0))
-				continue;
+		/*
+		 * For platform based machines, neither ERR nor NULL can happen here.
+		 * The s3c24xx_handle_irq() will be set as IRQ handler iff this succeeds:
+		 *
+		 *    s3c_intc[0] = s3c24xx_init_intc()
+		 *
+		 * If this fails, the next calls to s3c24xx_init_intc() won't be executed.
+		 *
+		 * For DT machine, s3c_init_intc_of() could set the IRQ handler without
+		 * setting s3c_intc[0] only if it was called with num_ctrl=0. There is no
+		 * such code path, so again the s3c_intc[0] will have a valid pointer if
+		 * set_handle_irq() is called.
+		 *
+		 * Therefore in s3c24xx_handle_irq(), the s3c_intc[0] is always something.
+		 */
+		if (s3c24xx_handle_intc(s3c_intc[0], regs, 0))
+			continue;
 
-		if (s3c_intc[2])
+		if (!IS_ERR_OR_NULL(s3c_intc[2]))
 			if (s3c24xx_handle_intc(s3c_intc[2], regs, 64))
 				continue;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-s3c/mach-jive.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-s3c/mach-jive.c
@@ -236,11 +236,11 @@
 	unsigned long set;
 
 	if (options == NULL || options[0] == '\0')
-		return 0;
+		return 1;
 
 	if (kstrtoul(options, 10, &set)) {
 		printk(KERN_ERR "failed to parse mtdset=%s\n", options);
-		return 0;
+		return 1;
 	}
 
 	switch (set) {
@@ -255,7 +255,7 @@
 		       "using default.", set);
 	}
 
-	return 0;
+	return 1;
 }
 
 /* parse the mtdset= option given to the kernel command line */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-s3c/s3c64xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-s3c/s3c64xx.c
@@ -173,7 +173,8 @@
 	.tclk_mask	= (1 << 7) | (1 << 6) | (1 << 5),
 };
 
-void __init s3c64xx_set_timer_source(unsigned int event, unsigned int source)
+void __init s3c64xx_set_timer_source(enum s3c64xx_timer_mode event,
+				     enum s3c64xx_timer_mode source)
 {
 	s3c64xx_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
 	s3c64xx_pwm_variant.output_mask &= ~(BIT(event) | BIT(source));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-sa1100/jornada720_ssp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-sa1100/jornada720_ssp.c
@@ -1,5 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
-/**
+/*
  *  arch/arm/mac-sa1100/jornada720_ssp.c
  *
  *  Copyright (C) 2006/2007 Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
@@ -26,6 +26,7 @@
 
 /**
  * jornada_ssp_reverse - reverses input byte
+ * @byte: input byte to reverse
  *
  * we need to reverse all data we receive from the mcu due to its physical location
  * returns : 01110111 -> 11101110
@@ -46,6 +47,7 @@
 
 /**
  * jornada_ssp_byte - waits for ready ssp bus and sends byte
+ * @byte: input byte to transmit
  *
  * waits for fifo buffer to clear and then transmits, if it doesn't then we will
  * timeout after <timeout> rounds. Needs mcu running before its called.
@@ -77,6 +79,7 @@
 
 /**
  * jornada_ssp_inout - decide if input is command or trading byte
+ * @byte: input byte to send (may be %TXDUMMY)
  *
  * returns : (jornada_ssp_byte(byte)) on success
  *         : %-ETIMEDOUT on timeout failure
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-shmobile/headsmp.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-shmobile/headsmp.S
@@ -136,6 +136,7 @@
 	.long	shmobile_smp_arg - 1b
 
 	.bss
+	.align	2
 	.globl	shmobile_smp_mpidr
 shmobile_smp_mpidr:
 	.space	NR_CPUS * 4
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
@@ -125,6 +125,7 @@
 
 	list_for_each_entry_safe(pos, tmp, &quirk_list, list) {
 		list_del(&pos->list);
+		of_node_put(pos->np);
 		kfree(pos);
 	}
 
@@ -154,8 +155,10 @@
 		return -ENODEV;
 
 	for_each_matching_node_and_match(np, rcar_gen2_quirk_match, &id) {
-		if (!of_device_is_available(np))
+		if (!of_device_is_available(np)) {
+			of_node_put(np);
 			break;
+		}
 
 		ret = of_property_read_u32(np, "reg", &addr);
 		if (ret)	/* Skip invalid entry and continue */
@@ -164,6 +167,7 @@
 		quirk = kzalloc(sizeof(*quirk), GFP_KERNEL);
 		if (!quirk) {
 			ret = -ENOMEM;
+			of_node_put(np);
 			goto err_mem;
 		}
 
@@ -171,11 +175,12 @@
 		memcpy(&quirk->i2c_msg, id->data, sizeof(quirk->i2c_msg));
 
 		quirk->id = id;
-		quirk->np = np;
+		quirk->np = of_node_get(np);
 		quirk->i2c_msg.addr = addr;
 
 		ret = of_irq_parse_one(np, 0, argsa);
 		if (ret) {	/* Skip invalid entry and continue */
+			of_node_put(np);
 			kfree(quirk);
 			continue;
 		}
@@ -222,6 +227,7 @@
 err_mem:
 	list_for_each_entry_safe(pos, tmp, &quirk_list, list) {
 		list_del(&pos->list);
+		of_node_put(pos->np);
 		kfree(pos);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-socfpga/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-socfpga/Kconfig
@@ -2,6 +2,7 @@
 menuconfig ARCH_INTEL_SOCFPGA
 	bool "Altera SOCFPGA family"
 	depends on ARCH_MULTI_V7
+	select ARCH_HAS_RESET_CONTROLLER
 	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARM_AMBA
 	select ARM_GIC
@@ -18,6 +19,7 @@
 	select PL310_ERRATA_727915
 	select PL310_ERRATA_753970 if PL310
 	select PL310_ERRATA_769419
+	select RESET_CONTROLLER
 
 if ARCH_INTEL_SOCFPGA
 config SOCFPGA_SUSPEND
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-socfpga/core.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-socfpga/core.h
@@ -33,7 +33,7 @@
 u32 socfpga_sdram_self_refresh(u32 sdr_base);
 extern unsigned int socfpga_sdram_self_refresh_sz;
 
-extern char secondary_trampoline, secondary_trampoline_end;
+extern char secondary_trampoline[], secondary_trampoline_end[];
 
 extern unsigned long socfpga_cpu1start_addr;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-socfpga/platsmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-socfpga/platsmp.c
@@ -20,14 +20,14 @@
 
 static int socfpga_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
-	int trampoline_size = &secondary_trampoline_end - &secondary_trampoline;
+	int trampoline_size = secondary_trampoline_end - secondary_trampoline;
 
 	if (socfpga_cpu1start_addr) {
 		/* This will put CPU #1 into reset. */
 		writel(RSTMGR_MPUMODRST_CPU1,
 		       rst_manager_base_addr + SOCFPGA_RSTMGR_MODMPURST);
 
-		memcpy(phys_to_virt(0), &secondary_trampoline, trampoline_size);
+		memcpy(phys_to_virt(0), secondary_trampoline, trampoline_size);
 
 		writel(__pa_symbol(secondary_startup),
 		       sys_manager_base_addr + (socfpga_cpu1start_addr & 0x000000ff));
@@ -45,12 +45,12 @@
 
 static int socfpga_a10_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
-	int trampoline_size = &secondary_trampoline_end - &secondary_trampoline;
+	int trampoline_size = secondary_trampoline_end - secondary_trampoline;
 
 	if (socfpga_cpu1start_addr) {
 		writel(RSTMGR_MPUMODRST_CPU1, rst_manager_base_addr +
 		       SOCFPGA_A10_RSTMGR_MODMPURST);
-		memcpy(phys_to_virt(0), &secondary_trampoline, trampoline_size);
+		memcpy(phys_to_virt(0), secondary_trampoline, trampoline_size);
 
 		writel(__pa_symbol(secondary_startup),
 		       sys_manager_base_addr + (socfpga_cpu1start_addr & 0x00000fff));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/generic.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/generic.h
@@ -1,13 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * spear machine family generic header file
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Rajeev Kumar <rajeev-dlh.kumar@st.com>
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_GENERIC_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/include/mach/misc_regs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/include/mach/misc_regs.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-spear3xx/include/mach/misc_regs.h
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_MISC_REGS_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/include/mach/spear.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/include/mach/spear.h
@@ -1,13 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SPEAr3xx/6xx Machine family specific definition
  *
  * Copyright (C) 2009,2012 ST Microelectronics
  * Rajeev Kumar<rajeev-dlh.kumar@st.com>
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_SPEAR_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/pl080.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/pl080.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/plat-spear/pl080.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/amba/pl08x.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/pl080.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/pl080.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/plat-spear/include/plat/pl080.h
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __PLAT_PL080_H
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/restart.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/restart.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/plat-spear/restart.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/io.h>
 #include <linux/amba/sp810.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear1310.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear1310.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear13xx/spear1310.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr1310: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear1340.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear1340.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear13xx/spear1340.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr1340: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear13xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear13xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear13xx/spear13xx.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr13xx: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear300.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear300.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear300.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr300: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear310.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear310.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear310.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr310: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear320.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear320.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear320.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr320: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear3xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear3xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear3xx.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr3xx: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/spear6xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/spear6xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear6xx/spear6xx.c
  *
@@ -7,10 +8,6 @@
  * Rajeev Kumar<rajeev-dlh.kumar@st.com>
  *
  * Copyright 2012 Stefan Roese <sr@denx.de>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/amba/pl08x.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-spear/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-spear/time.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/plat-spear/time.c
  *
  * Copyright (C) 2010 ST Microelectronics
  * Shiraz Hashim<shiraz.linux.kernel@gmail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk.h>
@@ -93,7 +90,7 @@
 		200, 16, clocksource_mmio_readw_up);
 }
 
-static inline void timer_shutdown(struct clock_event_device *evt)
+static inline void spear_timer_shutdown(struct clock_event_device *evt)
 {
 	u16 val = readw(gpt_base + CR(CLKEVT));
 
@@ -104,7 +101,7 @@
 
 static int spear_shutdown(struct clock_event_device *evt)
 {
-	timer_shutdown(evt);
+	spear_timer_shutdown(evt);
 
 	return 0;
 }
@@ -114,7 +111,7 @@
 	u16 val;
 
 	/* stop the timer */
-	timer_shutdown(evt);
+	spear_timer_shutdown(evt);
 
 	val = readw(gpt_base + CR(CLKEVT));
 	val |= CTRL_ONE_SHOT;
@@ -129,7 +126,7 @@
 	u16 val;
 
 	/* stop the timer */
-	timer_shutdown(evt);
+	spear_timer_shutdown(evt);
 
 	period = clk_get_rate(gpt_clk) / HZ;
 	period >>= CTRL_PRESCALER16;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-sunxi/mc_smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-sunxi/mc_smp.c
@@ -804,16 +804,16 @@
 	for (i = 0; i < ARRAY_SIZE(sunxi_mc_smp_data); i++) {
 		ret = of_property_match_string(node, "enable-method",
 					       sunxi_mc_smp_data[i].enable_method);
-		if (!ret)
+		if (ret >= 0)
 			break;
 	}
 
-	is_a83t = sunxi_mc_smp_data[i].is_a83t;
-
 	of_node_put(node);
-	if (ret)
+	if (ret < 0)
 		return -ENODEV;
 
+	is_a83t = sunxi_mc_smp_data[i].is_a83t;
+
 	if (!sunxi_mc_smp_cpu_table_init())
 		return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-vexpress/dcscb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-vexpress/dcscb.c
@@ -144,6 +144,7 @@
 	if (!node)
 		return -ENODEV;
 	dcscb_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!dcscb_base)
 		return -EADDRNOTAVAIL;
 	cfg = readl_relaxed(dcscb_base + DCS_CFG_R);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-vexpress/spc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-vexpress/spc.c
@@ -580,7 +580,7 @@
 		}
 
 		cluster = topology_physical_package_id(cpu_dev->id);
-		if (init_opp_table[cluster])
+		if (cluster < 0 || init_opp_table[cluster])
 			continue;
 
 		if (ve_init_opp_table(cpu_dev))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/Kconfig
@@ -16,3 +16,19 @@
 	select SOC_BUS
 	help
 	  Support for Xilinx Zynq ARM Cortex A9 Platform
+
+if ARCH_ZYNQ
+
+menu "Xilinx Specific Options"
+
+config XILINX_PREFETCH
+	bool "Cache Prefetch"
+	default y
+	help
+	  This option turns on L1 & L2 cache prefetching to get the best performance
+	  in many cases. This may not always be the best performance depending on
+	  the usage.
+
+endmenu
+
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/Makefile
@@ -4,5 +4,8 @@
 #
 
 # Common support
-obj-y				:= common.o slcr.o pm.o
+obj-y				:= common.o efuse.o slcr.o zynq_ocm.o pm.o
+
 obj-$(CONFIG_SMP)		+= headsmp.o platsmp.o
+obj-$(CONFIG_SUSPEND)	+= suspend.o
+AFLAGS_suspend.o		+=-Wa,-march=armv7-a
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/common.c
@@ -77,6 +77,7 @@
 	}
 
 	zynq_devcfg_base = of_iomap(np, 0);
+	of_node_put(np);
 	if (!zynq_devcfg_base) {
 		pr_err("%s: Unable to map I/O memory\n", __func__);
 		return -1;
@@ -95,6 +96,7 @@
 {
 	zynq_core_pm_init();
 	zynq_pm_late_init();
+	zynq_prefetch_init();
 }
 
 /**
@@ -175,6 +177,7 @@
 
 static void __init zynq_irq_init(void)
 {
+	zynq_early_efuse_init();
 	zynq_early_slcr_init();
 	irqchip_init();
 }
@@ -186,8 +189,13 @@
 
 DT_MACHINE_START(XILINX_EP107, "Xilinx Zynq Platform")
 	/* 64KB way size, 8-way associativity, parity disabled */
-	.l2c_aux_val    = 0x00400000,
+#ifdef CONFIG_XILINX_PREFETCH
+	.l2c_aux_val	= 0x30400000,
+	.l2c_aux_mask	= 0xcfbfffff,
+#else
+	.l2c_aux_val	= 0x00400000,
 	.l2c_aux_mask	= 0xffbfffff,
+#endif
 	.smp		= smp_ops(zynq_smp_ops),
 	.map_io		= zynq_map_io,
 	.init_irq	= zynq_irq_init,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/common.h
@@ -15,8 +15,12 @@
 extern void zynq_slcr_cpu_start(int cpu);
 extern bool zynq_slcr_cpu_state_read(int cpu);
 extern void zynq_slcr_cpu_state_write(int cpu, bool die);
+extern u32 zynq_slcr_get_ocm_config(void);
 extern u32 zynq_slcr_get_device_id(void);
 
+extern bool zynq_efuse_cpu_state(int cpu);
+extern int zynq_early_efuse_init(void);
+
 #ifdef CONFIG_SMP
 extern char zynq_secondary_trampoline;
 extern char zynq_secondary_trampoline_jump;
@@ -25,9 +29,31 @@
 extern const struct smp_operations zynq_smp_ops;
 #endif
 
+extern void zynq_slcr_init_preload_fpga(void);
+extern void zynq_slcr_init_postload_fpga(void);
+
+extern void __iomem *zynq_slcr_base;
 extern void __iomem *zynq_scu_base;
 
 void zynq_pm_late_init(void);
+extern unsigned int zynq_sys_suspend_sz;
+int zynq_sys_suspend(void __iomem *ddrc_base, void __iomem *slcr_base);
+
+static inline void zynq_prefetch_init(void)
+{
+	/*
+	 * Enable prefetching in aux control register. L2 prefetch must
+	 * only be enabled if the slave supports it (PL310 does)
+	 */
+	asm volatile ("mrc   p15, 0, r1, c1, c0, 1\n"
+#ifdef CONFIG_XILINX_PREFETCH
+		      "orr   r1, r1, #6\n"
+#else
+		      "bic   r1, r1, #6\n"
+#endif
+		      "mcr   p15, 0, r1, c1, c0, 1\n"
+		      : : : "r1");
+}
 
 static inline void zynq_core_pm_init(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/efuse.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/efuse.c
@@ -0,0 +1,78 @@
+/*
+ * Xilinx EFUSE driver
+ *
+ * Copyright (c) 2016 Xilinx Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include "common.h"
+
+#define EFUSE_STATUS_OFFSET	0x10
+
+/* 0 means cpu1 is working, 1 means cpu1 is broken */
+#define EFUSE_STATUS_CPU_BIT	BIT(7)
+
+void __iomem *zynq_efuse_base;
+
+/**
+ * zynq_efuse_cpu_state - Read/write cpu state
+ * @cpu:	cpu number
+ *
+ * Return: true if cpu is running, false if cpu is broken
+ */
+bool zynq_efuse_cpu_state(int cpu)
+{
+	u32 state;
+
+	if (!cpu)
+		return true;
+
+	if (!zynq_efuse_base)
+		return true;
+
+	state = readl(zynq_efuse_base + EFUSE_STATUS_OFFSET);
+	state &= EFUSE_STATUS_CPU_BIT;
+
+	if (!state)
+		return true;
+
+	return false;
+}
+
+/**
+ * zynq_early_efuse_init - Early efuse init function
+ *
+ * Return:	0 on success, negative errno otherwise.
+ *
+ * Called very early during boot from platform code.
+ */
+int __init zynq_early_efuse_init(void)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "xlnx,zynq-efuse");
+	if (!np) {
+		pr_err("%s: no efuse node found\n", __func__);
+		return -1;
+	}
+
+	zynq_efuse_base = of_iomap(np, 0);
+	if (!zynq_efuse_base) {
+		pr_err("%s: Unable to map I/O memory\n", __func__);
+		return -1;
+	}
+
+	np->data = (__force void *)zynq_efuse_base;
+
+	pr_info("%s mapped to %p\n", np->name, zynq_efuse_base);
+
+	of_node_put(np);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/platsmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/platsmp.c
@@ -83,6 +83,9 @@
 
 static int zynq_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
+	if (!zynq_efuse_cpu_state(cpu))
+		return -1;
+
 	return zynq_cpun_start(__pa_symbol(secondary_startup_arm), cpu);
 }
 
@@ -115,6 +118,7 @@
 static void zynq_secondary_init(unsigned int cpu)
 {
 	zynq_core_pm_init();
+	zynq_prefetch_init();
 }
 
 #ifdef CONFIG_HOTPLUG_CPU
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/pm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/pm.c
@@ -7,6 +7,14 @@
  *  Sören Brinkmann <soren.brinkmann@xilinx.com>
  */
 
+#include <linux/clk/zynq.h>
+#include <linux/genalloc.h>
+#include <linux/suspend.h>
+#include <asm/cacheflush.h>
+#include <asm/fncpy.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/mach/map.h>
+#include <asm/suspend.h>
 #include <linux/io.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
@@ -22,6 +30,165 @@
 
 static void __iomem *ddrc_base;
 
+#ifdef CONFIG_SUSPEND
+static int (*zynq_suspend_ptr)(void __iomem *, void __iomem *);
+
+static int zynq_pm_prepare_late(void)
+{
+	return zynq_clk_suspend_early();
+}
+
+static void zynq_pm_wake(void)
+{
+	zynq_clk_resume_late();
+}
+
+static int zynq_pm_suspend(unsigned long arg)
+{
+	u32 reg;
+	int do_ddrpll_bypass = 1;
+
+	/* Topswitch clock stop disable */
+	zynq_clk_topswitch_disable();
+
+	if (!zynq_suspend_ptr || !ddrc_base) {
+		do_ddrpll_bypass = 0;
+	} else {
+		/* enable DDRC self-refresh mode */
+		reg = readl(ddrc_base + DDRC_CTRL_REG1_OFFS);
+		reg |= DDRC_SELFREFRESH_MASK;
+		writel(reg, ddrc_base + DDRC_CTRL_REG1_OFFS);
+	}
+
+	if (do_ddrpll_bypass) {
+		/*
+		 * Going this way will turn off DDR related clocks and the DDR
+		 * PLL. I.e. We might brake sub systems relying on any of this
+		 * clocks. And even worse: If there are any other masters in the
+		 * system (e.g. in the PL) accessing DDR they are screwed.
+		 */
+		flush_cache_all();
+		if (zynq_suspend_ptr(ddrc_base, zynq_slcr_base))
+			pr_warn("DDR self refresh failed.\n");
+	} else {
+		WARN_ONCE(1, "DRAM self-refresh not available\n");
+		cpu_do_idle();
+	}
+
+	/* disable DDRC self-refresh mode */
+	if (do_ddrpll_bypass) {
+		reg = readl(ddrc_base + DDRC_CTRL_REG1_OFFS);
+		reg &= ~DDRC_SELFREFRESH_MASK;
+		writel(reg, ddrc_base + DDRC_CTRL_REG1_OFFS);
+	}
+
+	/* Topswitch clock stop enable */
+	zynq_clk_topswitch_enable();
+
+	return 0;
+}
+
+static int zynq_pm_enter(suspend_state_t suspend_state)
+{
+	switch (suspend_state) {
+	case PM_SUSPEND_STANDBY:
+	case PM_SUSPEND_MEM:
+		cpu_suspend(0, zynq_pm_suspend);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct platform_suspend_ops zynq_pm_ops = {
+	.prepare_late	= zynq_pm_prepare_late,
+	.enter		= zynq_pm_enter,
+	.wake		= zynq_pm_wake,
+	.valid		= suspend_valid_only_mem,
+};
+
+/**
+ * zynq_pm_remap_ocm() - Remap OCM
+ * Returns a pointer to the mapped memory or NULL.
+ *
+ * Remap the OCM.
+ */
+static void __iomem *zynq_pm_remap_ocm(void)
+{
+	struct device_node *np;
+	const char *comp = "xlnx,zynq-ocmc-1.0";
+	void __iomem *base = NULL;
+
+	np = of_find_compatible_node(NULL, NULL, comp);
+	if (np) {
+		struct device *dev;
+		unsigned long pool_addr;
+		unsigned long pool_addr_virt;
+		struct gen_pool *pool;
+
+		of_node_put(np);
+
+		dev = &(of_find_device_by_node(np)->dev);
+
+		/* Get OCM pool from device tree or platform data */
+		pool = gen_pool_get(dev, NULL);
+		if (!pool) {
+			pr_warn("%s: OCM pool is not available\n", __func__);
+			return NULL;
+		}
+
+		pool_addr_virt = gen_pool_alloc(pool, zynq_sys_suspend_sz);
+		if (!pool_addr_virt) {
+			pr_warn("%s: Can't get OCM poll\n", __func__);
+			return NULL;
+		}
+		pool_addr = gen_pool_virt_to_phys(pool, pool_addr_virt);
+		if (!pool_addr) {
+			pr_warn("%s: Can't get physical address of OCM pool\n",
+				__func__);
+			return NULL;
+		}
+		base = __arm_ioremap_exec(pool_addr, zynq_sys_suspend_sz,
+				     MT_MEMORY_RWX);
+		if (!base) {
+			pr_warn("%s: IOremap OCM pool failed\n", __func__);
+			return NULL;
+		}
+		pr_debug("%s: Remap OCM %s from %lx to %lx\n", __func__, comp,
+			 pool_addr_virt, (unsigned long)base);
+	} else {
+		pr_warn("%s: no compatible node found for '%s'\n", __func__,
+				comp);
+	}
+
+	return base;
+}
+
+static void zynq_pm_suspend_init(void)
+{
+	void __iomem *ocm_base = zynq_pm_remap_ocm();
+
+	if (!ocm_base) {
+		pr_warn("%s: Unable to map OCM.\n", __func__);
+	} else {
+		/*
+		 * Copy code to suspend system into OCM. The suspend code
+		 * needs to run from OCM as DRAM may no longer be available
+		 * when the PLL is stopped.
+		 */
+		zynq_suspend_ptr = fncpy((__force void *)ocm_base,
+					 (__force void *)&zynq_sys_suspend,
+					 zynq_sys_suspend_sz);
+	}
+
+	suspend_set_ops(&zynq_pm_ops);
+}
+#else	/* CONFIG_SUSPEND */
+static void zynq_pm_suspend_init(void) { };
+#endif	/* CONFIG_SUSPEND */
+
 /**
  * zynq_pm_ioremap() - Create IO mappings
  * @comp:	DT compatible string
@@ -68,4 +235,7 @@
 		reg |= DDRC_CLOCKSTOP_MASK;
 		writel(reg, ddrc_base + DDRC_DRAM_PARAM_REG3_OFFS);
 	}
+
+	/* set up suspend */
+	zynq_pm_suspend_init();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/slcr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/slcr.c
@@ -16,10 +16,13 @@
 /* register offsets */
 #define SLCR_UNLOCK_OFFSET		0x8   /* SCLR unlock register */
 #define SLCR_PS_RST_CTRL_OFFSET		0x200 /* PS Software Reset Control */
+#define SLCR_FPGA_RST_CTRL_OFFSET	0x240 /* FPGA Software Reset Control */
 #define SLCR_A9_CPU_RST_CTRL_OFFSET	0x244 /* CPU Software Reset Control */
 #define SLCR_REBOOT_STATUS_OFFSET	0x258 /* PS Reboot Status */
 #define SLCR_PSS_IDCODE			0x530 /* PS IDCODE */
 #define SLCR_L2C_RAM			0xA1C /* L2C_RAM in AR#54190 */
+#define SLCR_LVL_SHFTR_EN_OFFSET	0x900 /* Level Shifters Enable */
+#define SLCR_OCM_CFG_OFFSET		0x910 /* OCM Address Mapping */
 
 #define SLCR_UNLOCK_MAGIC		0xDF0D
 #define SLCR_A9_CPU_CLKSTOP		0x10
@@ -27,7 +30,7 @@
 #define SLCR_PSS_IDCODE_DEVICE_SHIFT	12
 #define SLCR_PSS_IDCODE_DEVICE_MASK	0x1F
 
-static void __iomem *zynq_slcr_base;
+void __iomem *zynq_slcr_base;
 static struct regmap *zynq_slcr_regmap;
 
 /**
@@ -116,6 +119,48 @@
 };
 
 /**
+ * zynq_slcr_get_ocm_config - Get SLCR OCM config
+ *
+ * return:	OCM config bits
+ */
+u32 zynq_slcr_get_ocm_config(void)
+{
+	u32 ret;
+
+	zynq_slcr_read(&ret, SLCR_OCM_CFG_OFFSET);
+	return ret;
+}
+
+/**
+ * zynq_slcr_init_preload_fpga - Disable communication from the PL to PS.
+ */
+void zynq_slcr_init_preload_fpga(void)
+{
+	/* Assert FPGA top level output resets */
+	zynq_slcr_write(0xF, SLCR_FPGA_RST_CTRL_OFFSET);
+
+	/* Disable level shifters */
+	zynq_slcr_write(0, SLCR_LVL_SHFTR_EN_OFFSET);
+
+	/* Enable output level shifters */
+	zynq_slcr_write(0xA, SLCR_LVL_SHFTR_EN_OFFSET);
+}
+EXPORT_SYMBOL(zynq_slcr_init_preload_fpga);
+
+/**
+ * zynq_slcr_init_postload_fpga - Re-enable communication from the PL to PS.
+ */
+void zynq_slcr_init_postload_fpga(void)
+{
+	/* Enable level shifters */
+	zynq_slcr_write(0xf, SLCR_LVL_SHFTR_EN_OFFSET);
+
+	/* Deassert AXI interface resets */
+	zynq_slcr_write(0, SLCR_FPGA_RST_CTRL_OFFSET);
+}
+EXPORT_SYMBOL(zynq_slcr_init_postload_fpga);
+
+/**
  * zynq_slcr_cpu_start - Start cpu
  * @cpu:	cpu number
  */
@@ -213,6 +258,7 @@
 	zynq_slcr_regmap = syscon_regmap_lookup_by_compatible("xlnx,zynq-slcr");
 	if (IS_ERR(zynq_slcr_regmap)) {
 		pr_err("%s: failed to find zynq-slcr\n", __func__);
+		of_node_put(np);
 		return -ENODEV;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/suspend.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/suspend.S
@@ -0,0 +1,177 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Suspend support for Zynq
+ *
+ *  Copyright (C) 2012 Xilinx
+ *
+ *  Soren Brinkmann <soren.brinkmann@xilinx.com>
+ */
+
+#include <linux/linkage.h>
+
+#define ARMPLL_CTRL_OFFS	0x100
+#define DDRPLL_CTRL_OFFS	0x104
+#define PLLSTATUS_OFFS		0x10c
+#define DDR_CLK_CTRL_OFFS	0x124
+#define DCI_CLK_CTRL_OFFS	0x128
+#define MODE_STS_OFFS		0x54
+
+#define PLL_RESET_MASK		1
+#define PLL_PWRDWN_MASK		(1 << 1)
+#define PLL_BYPASS_MASK		(1 << 4)
+#define DCICLK_ENABLE_MASK	1
+#define DDRCLK_ENABLE_MASK	3
+#define ARM_LOCK_MASK		(1 << 0)
+#define DDR_LOCK_MASK		(1 << 1)
+#define DDRC_STATUS_MASK	7
+
+#define DDRC_OPMODE_SR		3
+#define MAXTRIES		100
+
+	.text
+	.align 3
+
+/**
+ * zynq_sys_suspend - Enter suspend
+ * @ddrc_base:	Base address of the DDRC
+ * @slcr_base:	Base address of the SLCR
+ * Returns -1 if DRAM subsystem is not gated off, 0 otherwise.
+ *
+ * This function is moved into OCM and finishes the suspend operation. I.e. DDR
+ * related clocks are gated off and the DDR PLL is bypassed.
+ */
+ENTRY(zynq_sys_suspend)
+	push	{r4 - r7}
+
+	/* Check DDRC is in self-refresh mode */
+	ldr	r2, [r0, #MODE_STS_OFFS]
+	and	r2, #DDRC_STATUS_MASK
+	cmp	r2, #DDRC_OPMODE_SR
+	movweq	r3, #0xff00
+	bne	suspend
+
+	mov	r3, #MAXTRIES
+	movw	r4, #0xfff0
+	movt	r4, #0x1f
+	/* Wait for command queue empty */
+1:	subs	r3, #1
+	movweq	r3, #0xff00
+	beq	suspend
+	dsb	sy
+	ldr	r2, [r0, #MODE_STS_OFFS]
+	ands	r2, r4
+	bne	1b
+
+	dsb	sy
+
+	/*
+	 * Wait for DDRC pipeline/queues to drain.
+	 * We should wait ~40 DDR cycles. DDR is still at full speed while the
+	 * CPU might already run in PLL bypass mode. The fastest speed the CPU
+	 * runs at is ~1 GHz ~ 2 * DDR speed.
+	 */
+	mov	r3, #160
+1:	nop
+	subs	r3, #1
+	bne	1b
+
+	dsb	sy
+
+	/* read back CAM status once more */
+	ldr	r2, [r0, #MODE_STS_OFFS]
+	ands	r2, r4
+	movwne	r3, #0xff00
+	bne	suspend
+
+	/* Stop DDR clocks */
+	ldr	r2, [r1, #DDR_CLK_CTRL_OFFS]
+	bic	r2, #DDRCLK_ENABLE_MASK
+	str	r2, [r1, #DDR_CLK_CTRL_OFFS]
+
+	dmb	st
+
+	ldr	r2, [r1, #DCI_CLK_CTRL_OFFS]
+	bic	r2, #DCICLK_ENABLE_MASK
+	str	r2, [r1, #DCI_CLK_CTRL_OFFS]
+
+	dmb	st
+
+	/* Bypass and powerdown DDR PLL */
+	ldr	r2, [r1, #DDRPLL_CTRL_OFFS]
+	orr	r2, #PLL_BYPASS_MASK
+	str	r2, [r1, #DDRPLL_CTRL_OFFS]
+	orr	r2, #(PLL_PWRDWN_MASK | PLL_RESET_MASK)
+	str	r2, [r1, #DDRPLL_CTRL_OFFS]
+
+	/* Bypass and powerdown ARM PLL */
+	ldr	r2, [r1, #ARMPLL_CTRL_OFFS]
+	orr	r2, #PLL_BYPASS_MASK
+	str	r2, [r1, #ARMPLL_CTRL_OFFS]
+	orr	r2, #(PLL_PWRDWN_MASK | PLL_RESET_MASK)
+	str	r2, [r1, #ARMPLL_CTRL_OFFS]
+
+suspend:
+	dsb	sy
+	wfi
+	dsb	sy
+	cmp	r3, #0xff00
+	moveq	r0, #-1
+	beq	exit
+
+	/* Power up ARM PLL */
+	ldr	r2, [r1, #ARMPLL_CTRL_OFFS]
+	bic	r2, #(PLL_PWRDWN_MASK | PLL_RESET_MASK)
+	str	r2, [r1, #ARMPLL_CTRL_OFFS]
+	/* wait for lock */
+1:	ldr	r2, [r1, #PLLSTATUS_OFFS]
+	ands	r2, #ARM_LOCK_MASK
+	beq	1b
+
+	dsb	sy
+
+	/* Disable ARM PLL bypass */
+	ldr	r2, [r1, #ARMPLL_CTRL_OFFS]
+	bic	r2, #PLL_BYPASS_MASK
+	str	r2, [r1, #ARMPLL_CTRL_OFFS]
+
+	dmb	st
+
+	/* Power up DDR PLL */
+	ldr	r2, [r1, #DDRPLL_CTRL_OFFS]
+	bic	r2, #(PLL_PWRDWN_MASK | PLL_RESET_MASK)
+	str	r2, [r1, #DDRPLL_CTRL_OFFS]
+	/* wait for lock */
+1:	ldr	r2, [r1, #PLLSTATUS_OFFS]
+	ands	r2, #DDR_LOCK_MASK
+	beq	1b
+
+	dsb	sy
+
+	/* Disable DDR PLL bypass */
+	ldr	r2, [r1, #DDRPLL_CTRL_OFFS]
+	bic	r2, #PLL_BYPASS_MASK
+	str	r2, [r1, #DDRPLL_CTRL_OFFS]
+
+	dmb	st
+
+	/* Start DDR clocks */
+	ldr	r2, [r1, #DCI_CLK_CTRL_OFFS]
+	orr	r2, #DCICLK_ENABLE_MASK
+	str	r2, [r1, #DCI_CLK_CTRL_OFFS]
+
+	dmb	st
+
+	ldr	r2, [r1, #DDR_CLK_CTRL_OFFS]
+	orr	r2, #DDRCLK_ENABLE_MASK
+	str	r2, [r1, #DDR_CLK_CTRL_OFFS]
+
+	dsb	sy
+
+	mov	r0, #0
+exit:	pop	{r4 - r7}
+	bx	lr
+
+ENTRY(zynq_sys_suspend_sz)
+	.word	. - zynq_sys_suspend
+
+	ENDPROC(zynq_sys_suspend)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mach-zynq/zynq_ocm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mach-zynq/zynq_ocm.c
@@ -0,0 +1,245 @@
+/*
+ * Copyright (C) 2013 Xilinx
+ *
+ * Based on "Generic on-chip SRAM allocation driver"
+ *
+ * Copyright (C) 2012 Philipp Zabel, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/genalloc.h>
+
+#include "common.h"
+
+#define ZYNQ_OCM_HIGHADDR	0xfffc0000
+#define ZYNQ_OCM_LOWADDR	0x0
+#define ZYNQ_OCM_BLOCK_SIZE	0x10000
+#define ZYNQ_OCM_BLOCKS		4
+#define ZYNQ_OCM_GRANULARITY	32
+
+#define ZYNQ_OCM_PARITY_CTRL	0x0
+#define ZYNQ_OCM_PARITY_ENABLE	0x1e
+
+#define ZYNQ_OCM_PARITY_ERRADDRESS	0x4
+
+#define ZYNQ_OCM_IRQ_STS		0x8
+#define ZYNQ_OCM_IRQ_STS_ERR_MASK	0x7
+
+struct zynq_ocm_dev {
+	void __iomem *base;
+	int irq;
+	struct gen_pool *pool;
+	struct resource res[ZYNQ_OCM_BLOCKS];
+};
+
+/**
+ * zynq_ocm_irq_handler - Interrupt service routine of the OCM controller
+ * @irq:	IRQ number
+ * @data:	Pointer to the zynq_ocm_dev structure
+ *
+ * Return:	IRQ_HANDLED when handled; IRQ_NONE otherwise.
+ */
+static irqreturn_t zynq_ocm_irq_handler(int irq, void *data)
+{
+	u32 sts;
+	u32 err_addr;
+	struct zynq_ocm_dev *zynq_ocm = data;
+
+	/* check status */
+	sts = readl(zynq_ocm->base + ZYNQ_OCM_IRQ_STS);
+	if (sts & ZYNQ_OCM_IRQ_STS_ERR_MASK) {
+		/* check error address */
+		err_addr = readl(zynq_ocm->base + ZYNQ_OCM_PARITY_ERRADDRESS);
+		pr_err("%s: OCM err intr generated at 0x%04x (stat: 0x%08x).",
+		       __func__, err_addr, sts & ZYNQ_OCM_IRQ_STS_ERR_MASK);
+		return IRQ_HANDLED;
+	}
+	pr_warn("%s: Interrupt generated by OCM, but no error is found.",
+		__func__);
+
+	return IRQ_NONE;
+}
+
+/**
+ * zynq_ocm_probe - Probe method for the OCM driver
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * This function initializes the driver data structures and the hardware.
+ *
+ * Return:	0 on success and error value on failure
+ */
+static int zynq_ocm_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct zynq_ocm_dev *zynq_ocm;
+	u32 i, ocm_config, curr;
+	struct resource *res;
+
+	ocm_config = zynq_slcr_get_ocm_config();
+
+	zynq_ocm = devm_kzalloc(&pdev->dev, sizeof(*zynq_ocm), GFP_KERNEL);
+	if (!zynq_ocm)
+		return -ENOMEM;
+
+	zynq_ocm->pool = devm_gen_pool_create(&pdev->dev,
+					      ilog2(ZYNQ_OCM_GRANULARITY),
+					      NUMA_NO_NODE, NULL);
+	if (!zynq_ocm->pool)
+		return -ENOMEM;
+
+	curr = 0; /* For storing current struct resource for OCM */
+	for (i = 0; i < ZYNQ_OCM_BLOCKS; i++) {
+		u32 base, start, end;
+
+		/* Setup base address for 64kB OCM block */
+		if (ocm_config & BIT(i))
+			base = ZYNQ_OCM_HIGHADDR;
+		else
+			base = ZYNQ_OCM_LOWADDR;
+
+		/* Calculate start and end block addresses */
+		start = i * ZYNQ_OCM_BLOCK_SIZE + base;
+		end = start + (ZYNQ_OCM_BLOCK_SIZE - 1);
+
+		/* Concatenate OCM blocks together to get bigger pool */
+		if (i > 0 && start == (zynq_ocm->res[curr - 1].end + 1)) {
+			zynq_ocm->res[curr - 1].end = end;
+		} else {
+#ifdef CONFIG_SMP
+			/*
+			 * OCM block if placed at 0x0 has special meaning
+			 * for SMP because jump trampoline is added there.
+			 * Ensure that this address won't be allocated.
+			 */
+			if (!base) {
+				u32 trampoline_code_size =
+					&zynq_secondary_trampoline_end -
+					&zynq_secondary_trampoline;
+				dev_dbg(&pdev->dev,
+					"Allocate reset vector table %dB\n",
+					trampoline_code_size);
+				/* postpone start offset */
+				start += trampoline_code_size;
+			}
+#endif
+			/* First resource is always initialized */
+			zynq_ocm->res[curr].start = start;
+			zynq_ocm->res[curr].end = end;
+			zynq_ocm->res[curr].flags = IORESOURCE_MEM;
+			curr++; /* Increment curr value */
+		}
+		dev_dbg(&pdev->dev, "OCM block %d, start %x, end %x\n",
+			i, start, end);
+	}
+
+	/*
+	 * Separate pool allocation from OCM block detection to ensure
+	 * the biggest possible pool.
+	 */
+	for (i = 0; i < ZYNQ_OCM_BLOCKS; i++) {
+		unsigned long size;
+		void __iomem *virt_base;
+
+		/* Skip all zero size resources */
+		if (zynq_ocm->res[i].end == 0)
+			break;
+		dev_dbg(&pdev->dev, "OCM resources %d, start %x, end %x\n",
+			i, zynq_ocm->res[i].start, zynq_ocm->res[i].end);
+		size = resource_size(&zynq_ocm->res[i]);
+		virt_base = devm_ioremap_resource(&pdev->dev,
+						  &zynq_ocm->res[i]);
+		if (IS_ERR(virt_base))
+			return PTR_ERR(virt_base);
+
+		ret = gen_pool_add_virt(zynq_ocm->pool,
+					(unsigned long)virt_base,
+					zynq_ocm->res[i].start, size, -1);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "Gen pool failed\n");
+			return ret;
+		}
+		dev_info(&pdev->dev, "ZYNQ OCM pool: %ld KiB @ 0x%p\n",
+			 size / 1024, virt_base);
+	}
+
+	/* Get OCM config space */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	zynq_ocm->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(zynq_ocm->base))
+		return PTR_ERR(zynq_ocm->base);
+
+	/* Allocate OCM parity IRQ */
+	zynq_ocm->irq = platform_get_irq(pdev, 0);
+	if (zynq_ocm->irq < 0) {
+		dev_err(&pdev->dev, "irq resource not found\n");
+		return zynq_ocm->irq;
+	}
+	ret = devm_request_irq(&pdev->dev, zynq_ocm->irq, zynq_ocm_irq_handler,
+			       0, pdev->name, zynq_ocm);
+	if (ret != 0) {
+		dev_err(&pdev->dev, "request_irq failed\n");
+		return ret;
+	}
+
+	/* Enable parity errors */
+	writel(ZYNQ_OCM_PARITY_ENABLE, zynq_ocm->base + ZYNQ_OCM_PARITY_CTRL);
+
+	platform_set_drvdata(pdev, zynq_ocm);
+
+	return 0;
+}
+
+/**
+ * zynq_ocm_remove - Remove method for the OCM driver
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * This function is called if a device is physically removed from the system or
+ * if the driver module is being unloaded. It frees all resources allocated to
+ * the device.
+ *
+ * Return:	0 on success and error value on failure
+ */
+static int zynq_ocm_remove(struct platform_device *pdev)
+{
+	struct zynq_ocm_dev *zynq_ocm = platform_get_drvdata(pdev);
+
+	if (gen_pool_avail(zynq_ocm->pool) < gen_pool_size(zynq_ocm->pool))
+		dev_dbg(&pdev->dev, "removed while SRAM allocated\n");
+
+	return 0;
+}
+
+static struct of_device_id zynq_ocm_dt_ids[] = {
+	{ .compatible = "xlnx,zynq-ocmc-1.0" },
+	{ /* end of table */ }
+};
+
+static struct platform_driver zynq_ocm_driver = {
+	.driver = {
+		.name = "zynq-ocm",
+		.of_match_table = zynq_ocm_dt_ids,
+	},
+	.probe = zynq_ocm_probe,
+	.remove = zynq_ocm_remove,
+};
+
+static int __init zynq_ocm_init(void)
+{
+	return platform_driver_register(&zynq_ocm_driver);
+}
+
+arch_initcall(zynq_ocm_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/Kconfig
@@ -750,7 +750,7 @@
 config CPU_ENDIAN_BE8
 	bool
 	depends on CPU_BIG_ENDIAN
-	default CPU_V6 || CPU_V6K || CPU_V7
+	default CPU_V6 || CPU_V6K || CPU_V7 || CPU_V7M
 	help
 	  Support for the BE-8 (big-endian) mode on ARMv6 and ARMv7 processors.
 
@@ -830,6 +830,7 @@
 
 config CPU_SPECTRE
 	bool
+	select GENERIC_CPU_VULNERABILITIES
 
 config HARDEN_BRANCH_PREDICTOR
 	bool "Harden the branch predictor against aliasing attacks" if EXPERT
@@ -850,6 +851,16 @@
 
 	   If unsure, say Y.
 
+config HARDEN_BRANCH_HISTORY
+	bool "Harden Spectre style attacks against branch history" if EXPERT
+	depends on CPU_SPECTRE
+	default y
+	help
+	  Speculation attacks against some high-performance processors can
+	  make use of branch history to influence future speculation. When
+	  taking an exception, a sequence of branches overwrites the branch
+	  history, or branch history is invalidated.
+
 config TLS_REG_EMUL
 	bool
 	select NEED_KUSER_HELPERS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/alignment.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/alignment.c
@@ -935,6 +935,9 @@
 	if (type == TYPE_LDST)
 		do_alignment_finish_ldst(addr, instr, regs, offset);
 
+	if (thumb_mode(regs))
+		regs->ARM_cpsr = it_advance(regs->ARM_cpsr);
+
 	return 0;
 
  bad_or_fault:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/cache-feroceon-l2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/cache-feroceon-l2.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mm/cache-feroceon-l2.c - Feroceon L2 cache controller support
  *
  * Copyright (C) 2008 Marvell Semiconductor
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * References:
  * - Unified Layer 2 Cache for Feroceon CPU Cores,
  *   Document ID MV-S104858-00, Rev. A, October 23 2007.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/cache-tauros2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/cache-tauros2.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mm/cache-tauros2.c - Tauros2 L2 cache controller support
  *
  * Copyright (C) 2008 Marvell Semiconductor
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * References:
  * - PJ1 CPU Core Datasheet,
  *   Document ID MV-S104837-01, Rev 0.7, January 24 2008.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/dump.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/dump.c
@@ -346,7 +346,7 @@
 		addr = start + i * PMD_SIZE;
 		domain = get_domain_name(pmd);
 		if (pmd_none(*pmd) || pmd_large(*pmd) || !pmd_present(*pmd))
-			note_page(st, addr, 3, pmd_val(*pmd), domain);
+			note_page(st, addr, 4, pmd_val(*pmd), domain);
 		else
 			walk_pte(st, pmd, addr, domain);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/fault.c
@@ -26,6 +26,13 @@
 
 #ifdef CONFIG_MMU
 
+bool copy_from_kernel_nofault_allowed(const void *unsafe_src, size_t size)
+{
+	unsigned long addr = (unsigned long)unsafe_src;
+
+	return addr >= TASK_SIZE && ULONG_MAX - addr >= size;
+}
+
 /*
  * This is useful to dump out the page tables associated with
  * 'addr' in mm 'mm'.
@@ -125,7 +132,7 @@
 	show_pte(KERN_ALERT, mm, addr);
 	die("Oops", regs, fsr);
 	bust_spinlocks(0);
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 /*
@@ -552,6 +559,7 @@
 	if (!inf->fn(addr, ifsr | FSR_LNX_PF, regs))
 		return;
 
+	pr_alert("8<--- cut here ---\n");
 	pr_alert("Unhandled prefetch abort: %s (0x%03x) at 0x%08lx\n",
 		inf->name, ifsr, addr);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/flush.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/flush.c
@@ -280,6 +280,8 @@
 		return;
 
 	page = pfn_to_page(pfn);
+	if (PageReserved(page))
+		return;
 	if (cache_is_vipt_aliasing())
 		mapping = page_mapping_file(page);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/idmap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/idmap.c
@@ -84,8 +84,15 @@
 	unsigned long addr, end;
 	unsigned long next;
 
+#ifdef CONFIG_XIP_KERNEL
+	addr = (phys_addr_t)(text_start) - XIP_VIRT_ADDR(CONFIG_XIP_PHYS_ADDR)
+		+ CONFIG_XIP_PHYS_ADDR;
+	end = (phys_addr_t)(text_end) - XIP_VIRT_ADDR(CONFIG_XIP_PHYS_ADDR)
+		+ CONFIG_XIP_PHYS_ADDR;
+#else
 	addr = virt_to_idmap(text_start);
 	end = virt_to_idmap(text_end);
+#endif
 	pr_info("Setting up static identity map for 0x%lx - 0x%lx\n", addr, end);
 
 	prot |= PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_AF;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/ioremap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/ioremap.c
@@ -479,3 +479,11 @@
 {
 	early_ioremap_setup();
 }
+
+bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+				 unsigned long flags)
+{
+	unsigned long pfn = PHYS_PFN(offset);
+
+	return memblock_is_map_memory(pfn);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/kasan_init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/kasan_init.c
@@ -226,7 +226,7 @@
 	BUILD_BUG_ON(pgd_index(KASAN_SHADOW_START) !=
 		     pgd_index(KASAN_SHADOW_END));
 	memcpy(tmp_pmd_table,
-	       pgd_page_vaddr(*pgd_offset_k(KASAN_SHADOW_START)),
+	       (void*)pgd_page_vaddr(*pgd_offset_k(KASAN_SHADOW_START)),
 	       sizeof(tmp_pmd_table));
 	set_pgd(&tmp_pgd_table[pgd_index(KASAN_SHADOW_START)],
 		__pgd(__pa(tmp_pmd_table) | PMD_TYPE_TABLE | L_PGD_SWAPPER));
@@ -264,12 +264,17 @@
 
 	/*
 	 * 1. The module global variables are in MODULES_VADDR ~ MODULES_END,
-	 *    so we need to map this area.
+	 *    so we need to map this area if CONFIG_KASAN_VMALLOC=n. With
+	 *    VMALLOC support KASAN will manage this region dynamically,
+	 *    refer to kasan_populate_vmalloc() and ARM's implementation of
+	 *    module_alloc().
 	 * 2. PKMAP_BASE ~ PKMAP_BASE+PMD_SIZE's shadow and MODULES_VADDR
 	 *    ~ MODULES_END's shadow is in the same PMD_SIZE, so we can't
 	 *    use kasan_populate_zero_shadow.
 	 */
-	create_mapping((void *)MODULES_VADDR, (void *)(PKMAP_BASE + PMD_SIZE));
+	if (!IS_ENABLED(CONFIG_KASAN_VMALLOC) && IS_ENABLED(CONFIG_MODULES))
+		create_mapping((void *)MODULES_VADDR, (void *)(MODULES_END));
+	create_mapping((void *)PKMAP_BASE, (void *)(PKMAP_BASE + PMD_SIZE));
 
 	/*
 	 * KAsan may reuse the contents of kasan_early_shadow_pte directly, so
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/mmu.c
@@ -212,12 +212,14 @@
 static int __init early_cachepolicy(char *p)
 {
 	pr_warn("cachepolicy kernel parameter not supported without cp15\n");
+	return 0;
 }
 early_param("cachepolicy", early_cachepolicy);
 
 static int __init noalign_setup(char *__unused)
 {
 	pr_warn("noalign kernel parameter not supported without cp15\n");
+	return 1;
 }
 __setup("noalign", noalign_setup);
 
@@ -294,6 +296,17 @@
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
 		.domain    = DOMAIN_KERNEL,
 	},
+	[MT_MEMORY_RO] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+			     L_PTE_XN | L_PTE_RDONLY,
+		.prot_l1   = PMD_TYPE_TABLE,
+#ifdef CONFIG_ARM_LPAE
+		.prot_sect = PMD_TYPE_SECT | L_PMD_SECT_RDONLY | PMD_SECT_AP2,
+#else
+		.prot_sect = PMD_TYPE_SECT,
+#endif
+		.domain    = DOMAIN_KERNEL,
+	},
 	[MT_ROM] = {
 		.prot_sect = PMD_TYPE_SECT,
 		.domain    = DOMAIN_KERNEL,
@@ -390,9 +403,9 @@
 	BUILD_BUG_ON(__fix_to_virt(__end_of_fixed_addresses) < FIXADDR_START);
 	BUG_ON(idx >= __end_of_fixed_addresses);
 
-	/* we only support device mappings until pgprot_kernel has been set */
+	/* We support only device mappings before pgprot_kernel is set. */
 	if (WARN_ON(pgprot_val(prot) != pgprot_val(FIXMAP_PAGE_IO) &&
-		    pgprot_val(pgprot_kernel) == 0))
+		    pgprot_val(prot) && pgprot_val(pgprot_kernel) == 0))
 		return;
 
 	if (pgprot_val(prot))
@@ -487,6 +500,7 @@
 
 			/* Also setup NX memory mapping */
 			mem_types[MT_MEMORY_RW].prot_sect |= PMD_SECT_XN;
+			mem_types[MT_MEMORY_RO].prot_sect |= PMD_SECT_XN;
 		}
 		if (cpu_arch >= CPU_ARCH_ARMv7 && (cr & CR_TRE)) {
 			/*
@@ -566,6 +580,7 @@
 		mem_types[MT_ROM].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 		mem_types[MT_MINICLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 		mem_types[MT_CACHECLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
+		mem_types[MT_MEMORY_RO].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 #endif
 
 		/*
@@ -585,6 +600,8 @@
 			mem_types[MT_MEMORY_RWX].prot_pte |= L_PTE_SHARED;
 			mem_types[MT_MEMORY_RW].prot_sect |= PMD_SECT_S;
 			mem_types[MT_MEMORY_RW].prot_pte |= L_PTE_SHARED;
+			mem_types[MT_MEMORY_RO].prot_sect |= PMD_SECT_S;
+			mem_types[MT_MEMORY_RO].prot_pte |= L_PTE_SHARED;
 			mem_types[MT_MEMORY_DMA_READY].prot_pte |= L_PTE_SHARED;
 			mem_types[MT_MEMORY_RWX_NONCACHED].prot_sect |= PMD_SECT_S;
 			mem_types[MT_MEMORY_RWX_NONCACHED].prot_pte |= L_PTE_SHARED;
@@ -645,6 +662,8 @@
 	mem_types[MT_MEMORY_RWX].prot_pte |= kern_pgprot;
 	mem_types[MT_MEMORY_RW].prot_sect |= ecc_mask | cp->pmd;
 	mem_types[MT_MEMORY_RW].prot_pte |= kern_pgprot;
+	mem_types[MT_MEMORY_RO].prot_sect |= ecc_mask | cp->pmd;
+	mem_types[MT_MEMORY_RO].prot_pte |= kern_pgprot;
 	mem_types[MT_MEMORY_DMA_READY].prot_pte |= kern_pgprot;
 	mem_types[MT_MEMORY_RWX_NONCACHED].prot_sect |= ecc_mask;
 	mem_types[MT_ROM].prot_sect |= cp->pmd;
@@ -1358,23 +1377,11 @@
 		map.pfn = __phys_to_pfn(__atags_pointer & SECTION_MASK);
 		map.virtual = FDT_FIXED_BASE;
 		map.length = FDT_FIXED_SIZE;
-		map.type = MT_ROM;
+		map.type = MT_MEMORY_RO;
 		create_mapping(&map);
 	}
 
 	/*
-	 * Map the kernel if it is XIP.
-	 * It is always first in the modulearea.
-	 */
-#ifdef CONFIG_XIP_KERNEL
-	map.pfn = __phys_to_pfn(CONFIG_XIP_PHYS_ADDR & SECTION_MASK);
-	map.virtual = MODULES_VADDR;
-	map.length = ((unsigned long)_exiprom - map.virtual + ~SECTION_MASK) & SECTION_MASK;
-	map.type = MT_ROM;
-	create_mapping(&map);
-#endif
-
-	/*
 	 * Map the cache flushing regions.
 	 */
 #ifdef FLUSH_BASE
@@ -1563,12 +1570,27 @@
 	 * This will only persist until we turn on proper memory management later on
 	 * and we remap the whole kernel with page granularity.
 	 */
+#ifdef CONFIG_XIP_KERNEL
+	phys_addr_t kernel_nx_start = kernel_sec_start;
+#else
 	phys_addr_t kernel_x_start = kernel_sec_start;
 	phys_addr_t kernel_x_end = round_up(__pa(__init_end), SECTION_SIZE);
 	phys_addr_t kernel_nx_start = kernel_x_end;
+#endif
 	phys_addr_t kernel_nx_end = kernel_sec_end;
 	struct map_desc map;
 
+	/*
+	 * Map the kernel if it is XIP.
+	 * It is always first in the modulearea.
+	 */
+#ifdef CONFIG_XIP_KERNEL
+	map.pfn = __phys_to_pfn(CONFIG_XIP_PHYS_ADDR & SECTION_MASK);
+	map.virtual = MODULES_VADDR;
+	map.length = ((unsigned long)_exiprom - map.virtual + ~SECTION_MASK) & SECTION_MASK;
+	map.type = MT_ROM;
+	create_mapping(&map);
+#else
 	map.pfn = __phys_to_pfn(kernel_x_start);
 	map.virtual = __phys_to_virt(kernel_x_start);
 	map.length = kernel_x_end - kernel_x_start;
@@ -1578,7 +1600,7 @@
 	/* If the nx part is small it may end up covered by the tail of the RWX section */
 	if (kernel_x_end == kernel_nx_end)
 		return;
-
+#endif
 	map.pfn = __phys_to_pfn(kernel_nx_start);
 	map.virtual = __phys_to_virt(kernel_nx_start);
 	map.length = kernel_nx_end - kernel_nx_start;
@@ -1723,6 +1745,11 @@
 {
 	void *zero_page;
 
+#ifdef CONFIG_XIP_KERNEL
+	/* Store the kernel RW RAM region start/end in these variables */
+	kernel_sec_start = CONFIG_PHYS_OFFSET & SECTION_MASK;
+	kernel_sec_end = round_up(__pa(_end), SECTION_SIZE);
+#endif
 	pr_debug("physical kernel sections: 0x%08llx-0x%08llx\n",
 		 kernel_sec_start, kernel_sec_end);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/nommu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/nommu.c
@@ -26,6 +26,13 @@
 
 unsigned long vectors_base;
 
+/*
+ * empty_zero_page is a special page that is used for
+ * zero-initialized data and COW.
+ */
+struct page *empty_zero_page;
+EXPORT_SYMBOL(empty_zero_page);
+
 #ifdef CONFIG_ARM_MPU
 struct mpu_rgn_info mpu_rgn_info;
 #endif
@@ -148,9 +155,21 @@
  */
 void __init paging_init(const struct machine_desc *mdesc)
 {
+	void *zero_page;
+
 	early_trap_init((void *)vectors_base);
 	mpu_setup();
+
+	/* allocate the zero page. */
+	zero_page = (void *)memblock_alloc(PAGE_SIZE, PAGE_SIZE);
+	if (!zero_page)
+		panic("%s: Failed to allocate %lu bytes align=0x%lx\n",
+		      __func__, PAGE_SIZE, PAGE_SIZE);
+
 	bootmem_init();
+
+	empty_zero_page = virt_to_page(zero_page);
+	flush_dcache_page(empty_zero_page);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/mm/proc-v7-bugs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/mm/proc-v7-bugs.c
@@ -6,8 +6,35 @@
 #include <asm/cp15.h>
 #include <asm/cputype.h>
 #include <asm/proc-fns.h>
+#include <asm/spectre.h>
 #include <asm/system_misc.h>
 
+#ifdef CONFIG_ARM_PSCI
+static int __maybe_unused spectre_v2_get_cpu_fw_mitigation_state(void)
+{
+	struct arm_smccc_res res;
+
+	arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
+			     ARM_SMCCC_ARCH_WORKAROUND_1, &res);
+
+	switch ((int)res.a0) {
+	case SMCCC_RET_SUCCESS:
+		return SPECTRE_MITIGATED;
+
+	case SMCCC_ARCH_WORKAROUND_RET_UNAFFECTED:
+		return SPECTRE_UNAFFECTED;
+
+	default:
+		return SPECTRE_VULNERABLE;
+	}
+}
+#else
+static int __maybe_unused spectre_v2_get_cpu_fw_mitigation_state(void)
+{
+	return SPECTRE_VULNERABLE;
+}
+#endif
+
 #ifdef CONFIG_HARDEN_BRANCH_PREDICTOR
 DEFINE_PER_CPU(harden_branch_predictor_fn_t, harden_branch_predictor_fn);
 
@@ -36,13 +63,60 @@
 	arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL);
 }
 
-static void cpu_v7_spectre_init(void)
+static unsigned int spectre_v2_install_workaround(unsigned int method)
 {
 	const char *spectre_v2_method = NULL;
 	int cpu = smp_processor_id();
 
 	if (per_cpu(harden_branch_predictor_fn, cpu))
-		return;
+		return SPECTRE_MITIGATED;
+
+	switch (method) {
+	case SPECTRE_V2_METHOD_BPIALL:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			harden_branch_predictor_bpiall;
+		spectre_v2_method = "BPIALL";
+		break;
+
+	case SPECTRE_V2_METHOD_ICIALLU:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			harden_branch_predictor_iciallu;
+		spectre_v2_method = "ICIALLU";
+		break;
+
+	case SPECTRE_V2_METHOD_HVC:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			call_hvc_arch_workaround_1;
+		cpu_do_switch_mm = cpu_v7_hvc_switch_mm;
+		spectre_v2_method = "hypervisor";
+		break;
+
+	case SPECTRE_V2_METHOD_SMC:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			call_smc_arch_workaround_1;
+		cpu_do_switch_mm = cpu_v7_smc_switch_mm;
+		spectre_v2_method = "firmware";
+		break;
+	}
+
+	if (spectre_v2_method)
+		pr_info("CPU%u: Spectre v2: using %s workaround\n",
+			smp_processor_id(), spectre_v2_method);
+
+	return SPECTRE_MITIGATED;
+}
+#else
+static unsigned int spectre_v2_install_workaround(unsigned int method)
+{
+	pr_info_once("Spectre V2: workarounds disabled by configuration\n");
+
+	return SPECTRE_VULNERABLE;
+}
+#endif
+
+static void cpu_v7_spectre_v2_init(void)
+{
+	unsigned int state, method = 0;
 
 	switch (read_cpuid_part()) {
 	case ARM_CPU_PART_CORTEX_A8:
@@ -51,69 +125,133 @@
 	case ARM_CPU_PART_CORTEX_A17:
 	case ARM_CPU_PART_CORTEX_A73:
 	case ARM_CPU_PART_CORTEX_A75:
-		per_cpu(harden_branch_predictor_fn, cpu) =
-			harden_branch_predictor_bpiall;
-		spectre_v2_method = "BPIALL";
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_BPIALL;
 		break;
 
 	case ARM_CPU_PART_CORTEX_A15:
 	case ARM_CPU_PART_BRAHMA_B15:
-		per_cpu(harden_branch_predictor_fn, cpu) =
-			harden_branch_predictor_iciallu;
-		spectre_v2_method = "ICIALLU";
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_ICIALLU;
 		break;
 
-#ifdef CONFIG_ARM_PSCI
 	case ARM_CPU_PART_BRAHMA_B53:
 		/* Requires no workaround */
+		state = SPECTRE_UNAFFECTED;
 		break;
+
 	default:
 		/* Other ARM CPUs require no workaround */
-		if (read_cpuid_implementor() == ARM_CPU_IMP_ARM)
+		if (read_cpuid_implementor() == ARM_CPU_IMP_ARM) {
+			state = SPECTRE_UNAFFECTED;
 			break;
+		}
+
 		fallthrough;
-		/* Cortex A57/A72 require firmware workaround */
-	case ARM_CPU_PART_CORTEX_A57:
-	case ARM_CPU_PART_CORTEX_A72: {
-		struct arm_smccc_res res;
 
-		arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
-				     ARM_SMCCC_ARCH_WORKAROUND_1, &res);
-		if ((int)res.a0 != 0)
-			return;
+	/* Cortex A57/A72 require firmware workaround */
+	case ARM_CPU_PART_CORTEX_A57:
+	case ARM_CPU_PART_CORTEX_A72:
+		state = spectre_v2_get_cpu_fw_mitigation_state();
+		if (state != SPECTRE_MITIGATED)
+			break;
 
 		switch (arm_smccc_1_1_get_conduit()) {
 		case SMCCC_CONDUIT_HVC:
-			per_cpu(harden_branch_predictor_fn, cpu) =
-				call_hvc_arch_workaround_1;
-			cpu_do_switch_mm = cpu_v7_hvc_switch_mm;
-			spectre_v2_method = "hypervisor";
+			method = SPECTRE_V2_METHOD_HVC;
 			break;
 
 		case SMCCC_CONDUIT_SMC:
-			per_cpu(harden_branch_predictor_fn, cpu) =
-				call_smc_arch_workaround_1;
-			cpu_do_switch_mm = cpu_v7_smc_switch_mm;
-			spectre_v2_method = "firmware";
+			method = SPECTRE_V2_METHOD_SMC;
 			break;
 
 		default:
+			state = SPECTRE_VULNERABLE;
 			break;
 		}
 	}
-#endif
+
+	if (state == SPECTRE_MITIGATED)
+		state = spectre_v2_install_workaround(method);
+
+	spectre_v2_update_state(state, method);
+}
+
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+static int spectre_bhb_method;
+
+static const char *spectre_bhb_method_name(int method)
+{
+	switch (method) {
+	case SPECTRE_V2_METHOD_LOOP8:
+		return "loop";
+
+	case SPECTRE_V2_METHOD_BPIALL:
+		return "BPIALL";
+
+	default:
+		return "unknown";
 	}
+}
 
-	if (spectre_v2_method)
-		pr_info("CPU%u: Spectre v2: using %s workaround\n",
-			smp_processor_id(), spectre_v2_method);
+static int spectre_bhb_install_workaround(int method)
+{
+	if (spectre_bhb_method != method) {
+		if (spectre_bhb_method) {
+			pr_err("CPU%u: Spectre BHB: method disagreement, system vulnerable\n",
+			       smp_processor_id());
+
+			return SPECTRE_VULNERABLE;
+		}
+
+		if (spectre_bhb_update_vectors(method) == SPECTRE_VULNERABLE)
+			return SPECTRE_VULNERABLE;
+
+		spectre_bhb_method = method;
+
+		pr_info("CPU%u: Spectre BHB: enabling %s workaround for all CPUs\n",
+			smp_processor_id(), spectre_bhb_method_name(method));
+	}
+
+	return SPECTRE_MITIGATED;
 }
 #else
-static void cpu_v7_spectre_init(void)
+static int spectre_bhb_install_workaround(int method)
 {
+	return SPECTRE_VULNERABLE;
 }
 #endif
 
+static void cpu_v7_spectre_bhb_init(void)
+{
+	unsigned int state, method = 0;
+
+	switch (read_cpuid_part()) {
+	case ARM_CPU_PART_CORTEX_A15:
+	case ARM_CPU_PART_BRAHMA_B15:
+	case ARM_CPU_PART_CORTEX_A57:
+	case ARM_CPU_PART_CORTEX_A72:
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_LOOP8;
+		break;
+
+	case ARM_CPU_PART_CORTEX_A73:
+	case ARM_CPU_PART_CORTEX_A75:
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_BPIALL;
+		break;
+
+	default:
+		state = SPECTRE_UNAFFECTED;
+		break;
+	}
+
+	if (state == SPECTRE_MITIGATED)
+		state = spectre_bhb_install_workaround(method);
+
+	spectre_v2_update_state(state, method);
+}
+
 static __maybe_unused bool cpu_v7_check_auxcr_set(bool *warned,
 						  u32 mask, const char *msg)
 {
@@ -142,16 +280,18 @@
 void cpu_v7_ca8_ibe(void)
 {
 	if (check_spectre_auxcr(this_cpu_ptr(&spectre_warned), BIT(6)))
-		cpu_v7_spectre_init();
+		cpu_v7_spectre_v2_init();
 }
 
 void cpu_v7_ca15_ibe(void)
 {
 	if (check_spectre_auxcr(this_cpu_ptr(&spectre_warned), BIT(0)))
-		cpu_v7_spectre_init();
+		cpu_v7_spectre_v2_init();
+	cpu_v7_spectre_bhb_init();
 }
 
 void cpu_v7_bugs_init(void)
 {
-	cpu_v7_spectre_init();
+	cpu_v7_spectre_v2_init();
+	cpu_v7_spectre_bhb_init();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/nwfpe/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/nwfpe/Makefile
@@ -11,3 +11,9 @@
 				   entry.o
 
 nwfpe-$(CONFIG_FPE_NWFPE_XP)	+= extended_cpdo.o
+
+# Try really hard to avoid generating calls to __aeabi_uldivmod() from
+# float64_rem() due to loop elision.
+ifdef CONFIG_CC_IS_CLANG
+CFLAGS_softfloat.o	+= -mllvm -replexitval=never
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/decode.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/decode.h
@@ -14,6 +14,7 @@
 #include <linux/types.h>
 #include <linux/stddef.h>
 #include <asm/probes.h>
+#include <asm/ptrace.h>
 #include <asm/kprobes.h>
 
 void __init arm_probes_decode_init(void);
@@ -35,31 +36,6 @@
 #endif
 
 
-/*
- * Update ITSTATE after normal execution of an IT block instruction.
- *
- * The 8 IT state bits are split into two parts in CPSR:
- *	ITSTATE<1:0> are in CPSR<26:25>
- *	ITSTATE<7:2> are in CPSR<15:10>
- */
-static inline unsigned long it_advance(unsigned long cpsr)
-	{
-	if ((cpsr & 0x06000400) == 0) {
-		/* ITSTATE<2:0> == 0 means end of IT block, so clear IT state */
-		cpsr &= ~PSR_IT_MASK;
-	} else {
-		/* We need to shift left ITSTATE<4:0> */
-		const unsigned long mask = 0x06001c00;  /* Mask ITSTATE<4:0> */
-		unsigned long it = cpsr & mask;
-		it <<= 1;
-		it |= it >> (27 - 10);  /* Carry ITSTATE<2> to correct place */
-		it &= mask;
-		cpsr &= ~mask;
-		cpsr |= it;
-	}
-	return cpsr;
-}
-
 static inline void __kprobes bx_write_pc(long pcv, struct pt_regs *regs)
 {
 	long cpsr = regs->ARM_cpsr;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/kprobes/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/kprobes/Makefile
@@ -1,4 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
+KASAN_SANITIZE_actions-common.o := n
+KASAN_SANITIZE_actions-arm.o := n
+KASAN_SANITIZE_actions-thumb.o := n
 obj-$(CONFIG_KPROBES)		+= core.o actions-common.o checkers-common.o
 obj-$(CONFIG_ARM_KPROBES_TEST)	+= test-kprobes.o
 test-kprobes-objs		:= test-core.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/kprobes/checkers-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/kprobes/checkers-common.c
@@ -40,7 +40,7 @@
  * Different from other insn uses imm8, the real addressing offset of
  * STRD in T32 encoding should be imm8 * 4. See ARMARM description.
  */
-enum probes_insn checker_stack_use_t32strd(probes_opcode_t insn,
+static enum probes_insn checker_stack_use_t32strd(probes_opcode_t insn,
 		struct arch_probes_insn *asi,
 		const struct decode_header *h)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/kprobes/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/kprobes/core.c
@@ -11,6 +11,8 @@
  * Copyright (C) 2007 Marvell Ltd.
  */
 
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/kernel.h>
 #include <linux/kprobes.h>
 #include <linux/module.h>
@@ -231,7 +233,7 @@
  * kprobe, and that level is reserved for user kprobe handlers, so we can't
  * risk encountering a new kprobe in an interrupt handler.
  */
-void __kprobes kprobe_handler(struct pt_regs *regs)
+static void __kprobes kprobe_handler(struct pt_regs *regs)
 {
 	struct kprobe *p, *cur;
 	struct kprobe_ctlblk *kcb;
@@ -278,7 +280,7 @@
 				break;
 			case KPROBE_REENTER:
 				/* A nested probe was hit in FIQ, it is a BUG */
-				pr_warn("Unrecoverable kprobe detected.\n");
+				pr_warn("Failed to recover from reentered kprobes.\n");
 				dump_kprobe(p);
 				fallthrough;
 			default:
@@ -371,7 +373,7 @@
  * for kretprobe handlers which should normally be interested in r0 only
  * anyway.
  */
-void __naked __kprobes kretprobe_trampoline(void)
+void __naked __kprobes __kretprobe_trampoline(void)
 {
 	__asm__ __volatile__ (
 		"stmdb	sp!, {r0 - r11}		\n\t"
@@ -387,11 +389,10 @@
 		: : : "memory");
 }
 
-/* Called from kretprobe_trampoline */
+/* Called from __kretprobe_trampoline */
 static __used __kprobes void *trampoline_handler(struct pt_regs *regs)
 {
-	return (void *)kretprobe_trampoline_handler(regs, &kretprobe_trampoline,
-						    (void *)regs->ARM_fp);
+	return (void *)kretprobe_trampoline_handler(regs, (void *)regs->ARM_fp);
 }
 
 void __kprobes arch_prepare_kretprobe(struct kretprobe_instance *ri,
@@ -401,7 +402,7 @@
 	ri->fp = (void *)regs->ARM_fp;
 
 	/* Replace the return addr with trampoline addr. */
-	regs->ARM_lr = (unsigned long)&kretprobe_trampoline;
+	regs->ARM_lr = (unsigned long)&__kretprobe_trampoline;
 }
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/kprobes/opt-arm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/kprobes/opt-arm.c
@@ -145,8 +145,6 @@
 	}
 }
 
-extern void kprobe_handler(struct pt_regs *regs);
-
 static void
 optimized_callback(struct optimized_kprobe *op, struct pt_regs *regs)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/kprobes/test-core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/kprobes/test-core.c
@@ -720,7 +720,7 @@
 	[REG_TYPE_NOSPPCX]	= COVERAGE_ANY_REG | COVERAGE_SP,
 };
 
-unsigned coverage_start_registers(const struct decode_header *h)
+static unsigned coverage_start_registers(const struct decode_header *h)
 {
 	unsigned regs = 0;
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/probes/kprobes/test-core.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/probes/kprobes/test-core.h
@@ -454,3 +454,7 @@
 #else
 void kprobe_arm_test_cases(void);
 #endif
+
+void __kprobes_test_case_start(void);
+void __kprobes_test_case_end_16(void);
+void __kprobes_test_case_end_32(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/xen/enlighten.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/xen/enlighten.c
@@ -159,9 +159,6 @@
 	BUG_ON(err);
 	per_cpu(xen_vcpu, cpu) = vcpup;
 
-	if (!xen_kernel_unmapped_at_usr())
-		xen_setup_runstate_info(cpu);
-
 after_register_vcpu_info:
 	enable_percpu_irq(xen_events_irq, 0);
 	return 0;
@@ -362,7 +359,8 @@
 	 * for secondary CPUs as they are brought up.
 	 * For uniformity we use VCPUOP_register_vcpu_info even on cpu0.
 	 */
-	xen_vcpu_info = alloc_percpu(struct vcpu_info);
+	xen_vcpu_info = __alloc_percpu(sizeof(struct vcpu_info),
+				       1 << fls(sizeof(struct vcpu_info) - 1));
 	if (xen_vcpu_info == NULL)
 		return -ENOMEM;
 
@@ -394,9 +392,6 @@
 		return -EINVAL;
 	}
 
-	if (!xen_kernel_unmapped_at_usr())
-		xen_time_setup_guest();
-
 	if (xen_initial_domain())
 		pvclock_gtod_register_notifier(&xen_pvclock_gtod_notifier);
 
@@ -406,7 +401,13 @@
 }
 early_initcall(xen_guest_init);
 
-static int __init xen_pm_init(void)
+static int xen_starting_runstate_cpu(unsigned int cpu)
+{
+	xen_setup_runstate_info(cpu);
+	return 0;
+}
+
+static int __init xen_late_init(void)
 {
 	if (!xen_domain())
 		return -ENODEV;
@@ -419,9 +420,16 @@
 		do_settimeofday64(&ts);
 	}
 
-	return 0;
+	if (xen_kernel_unmapped_at_usr())
+		return 0;
+
+	xen_time_setup_guest();
+
+	return cpuhp_setup_state(CPUHP_AP_ARM_XEN_RUNSTATE_STARTING,
+				 "arm/xen_runstate:starting",
+				 xen_starting_runstate_cpu, NULL);
 }
-late_initcall(xen_pm_init);
+late_initcall(xen_late_init);
 
 
 /* empty stubs */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm/xen/p2m.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm/xen/p2m.c
@@ -63,11 +63,12 @@
 
 unsigned long __pfn_to_mfn(unsigned long pfn)
 {
-	struct rb_node *n = phys_to_mach.rb_node;
+	struct rb_node *n;
 	struct xen_p2m_entry *entry;
 	unsigned long irqflags;
 
 	read_lock_irqsave(&p2m_lock, irqflags);
+	n = phys_to_mach.rb_node;
 	while (n) {
 		entry = rb_entry(n, struct xen_p2m_entry, rbnode_phys);
 		if (entry->pfn <= pfn &&
@@ -152,10 +153,11 @@
 	int rc;
 	unsigned long irqflags;
 	struct xen_p2m_entry *p2m_entry;
-	struct rb_node *n = phys_to_mach.rb_node;
+	struct rb_node *n;
 
 	if (mfn == INVALID_P2M_ENTRY) {
 		write_lock_irqsave(&p2m_lock, irqflags);
+		n = phys_to_mach.rb_node;
 		while (n) {
 			p2m_entry = rb_entry(n, struct xen_p2m_entry, rbnode_phys);
 			if (p2m_entry->pfn <= pfn &&
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/Kconfig
@@ -154,7 +154,6 @@
 	select HAVE_ARCH_KGDB
 	select HAVE_ARCH_MMAP_RND_BITS
 	select HAVE_ARCH_MMAP_RND_COMPAT_BITS if COMPAT
-	select HAVE_ARCH_PFN_VALID
 	select HAVE_ARCH_PREL32_RELOCATIONS
 	select HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET
 	select HAVE_ARCH_SECCOMP_FILTER
@@ -221,6 +220,7 @@
 	select THREAD_INFO_IN_TASK
 	select HAVE_ARCH_USERFAULTFD_MINOR if USERFAULTFD
 	select TRACE_IRQFLAGS_SUPPORT
+	select TRACE_IRQFLAGS_NMI_SUPPORT
 	help
 	  ARM 64-bit (AArch64) Linux support.
 
@@ -487,6 +487,22 @@
 
 	  If unsure, say Y.
 
+config ARM64_ERRATUM_1742098
+	bool "Cortex-A57/A72: 1742098: ELR recorded incorrectly on interrupt taken between cryptographic instructions in a sequence"
+	depends on COMPAT
+	default y
+	help
+	  This option removes the AES hwcap for aarch32 user-space to
+	  workaround erratum 1742098 on Cortex-A57 and Cortex-A72.
+
+	  Affected parts may corrupt the AES state if an interrupt is
+	  taken between a pair of AES instructions. These instructions
+	  are only present if the cryptography extensions are present.
+	  All software should have a fallback implementation for CPUs
+	  that don't implement the cryptography extensions.
+
+	  If unsure, say Y.
+
 config ARM64_ERRATUM_845719
 	bool "Cortex-A53: 845719: a load might read incorrect data"
 	depends on COMPAT
@@ -596,6 +612,23 @@
 config ARM64_WORKAROUND_REPEAT_TLBI
 	bool
 
+config ARM64_ERRATUM_2441007
+	bool "Cortex-A55: Completion of affected memory accesses might not be guaranteed by completion of a TLBI"
+	default y
+	select ARM64_WORKAROUND_REPEAT_TLBI
+	help
+	  This option adds a workaround for ARM Cortex-A55 erratum #2441007.
+
+	  Under very rare circumstances, affected Cortex-A55 CPUs
+	  may not handle a race between a break-before-make sequence on one
+	  CPU, and another CPU accessing the same page. This could allow a
+	  store to a page that has been unmapped.
+
+	  Work around this by adding the affected CPUs to the list that needs
+	  TLB sequences to be done twice.
+
+	  If unsure, say Y.
+
 config ARM64_ERRATUM_1286807
 	bool "Cortex-A76: Modification of the translation table for a virtual address might lead to read-after-read ordering violation"
 	default y
@@ -666,6 +699,195 @@
 
 	  If unsure, say Y.
 
+config ARM64_ERRATUM_2441009
+	bool "Cortex-A510: Completion of affected memory accesses might not be guaranteed by completion of a TLBI"
+	default y
+	select ARM64_WORKAROUND_REPEAT_TLBI
+	help
+	  This option adds a workaround for ARM Cortex-A510 erratum #2441009.
+
+	  Under very rare circumstances, affected Cortex-A510 CPUs
+	  may not handle a race between a break-before-make sequence on one
+	  CPU, and another CPU accessing the same page. This could allow a
+	  store to a page that has been unmapped.
+
+	  Work around this by adding the affected CPUs to the list that needs
+	  TLB sequences to be done twice.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2457168
+	bool "Cortex-A510: 2457168: workaround for AMEVCNTR01 incrementing incorrectly"
+	depends on ARM64_AMU_EXTN
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 2457168.
+
+	  The AMU counter AMEVCNTR01 (constant counter) should increment at the same rate
+	  as the system counter. On affected Cortex-A510 cores AMEVCNTR01 increments
+	  incorrectly giving a significantly higher output value.
+
+	  Work around this problem by returning 0 when reading the affected counter in
+	  key locations that results in disabling all users of this counter. This effect
+	  is the same to firmware disabling affected counters.
+
+	  If unsure, say Y.
+
+config ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	bool
+
+config ARM64_ERRATUM_2119858
+	bool "Cortex-A710: 2119858: workaround TRBE overwriting trace data in FILL mode"
+	default y
+	depends on COMPILE_TEST # Until the CoreSight TRBE driver changes are in
+	depends on CORESIGHT_TRBE
+	select ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	help
+	  This option adds the workaround for ARM Cortex-A710 erratum 2119858.
+
+	  Affected Cortex-A710 cores could overwrite up to 3 cache lines of trace
+	  data at the base of the buffer (pointed to by TRBASER_EL1) in FILL mode in
+	  the event of a WRAP event.
+
+	  Work around the issue by always making sure we move the TRBPTR_EL1 by
+	  256 bytes before enabling the buffer and filling the first 256 bytes of
+	  the buffer with ETM ignore packets upon disabling.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2139208
+	bool "Neoverse-N2: 2139208: workaround TRBE overwriting trace data in FILL mode"
+	default y
+	depends on COMPILE_TEST # Until the CoreSight TRBE driver changes are in
+	depends on CORESIGHT_TRBE
+	select ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	help
+	  This option adds the workaround for ARM Neoverse-N2 erratum 2139208.
+
+	  Affected Neoverse-N2 cores could overwrite up to 3 cache lines of trace
+	  data at the base of the buffer (pointed to by TRBASER_EL1) in FILL mode in
+	  the event of a WRAP event.
+
+	  Work around the issue by always making sure we move the TRBPTR_EL1 by
+	  256 bytes before enabling the buffer and filling the first 256 bytes of
+	  the buffer with ETM ignore packets upon disabling.
+
+	  If unsure, say Y.
+
+config ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+	bool
+
+config ARM64_ERRATUM_2054223
+	bool "Cortex-A710: 2054223: workaround TSB instruction failing to flush trace"
+	default y
+	select ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+	help
+	  Enable workaround for ARM Cortex-A710 erratum 2054223
+
+	  Affected cores may fail to flush the trace data on a TSB instruction, when
+	  the PE is in trace prohibited state. This will cause losing a few bytes
+	  of the trace cached.
+
+	  Workaround is to issue two TSB consecutively on affected cores.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2067961
+	bool "Neoverse-N2: 2067961: workaround TSB instruction failing to flush trace"
+	default y
+	select ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+	help
+	  Enable workaround for ARM Neoverse-N2 erratum 2067961
+
+	  Affected cores may fail to flush the trace data on a TSB instruction, when
+	  the PE is in trace prohibited state. This will cause losing a few bytes
+	  of the trace cached.
+
+	  Workaround is to issue two TSB consecutively on affected cores.
+
+	  If unsure, say Y.
+
+config ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
+	bool
+
+config ARM64_ERRATUM_2253138
+	bool "Neoverse-N2: 2253138: workaround TRBE writing to address out-of-range"
+	depends on COMPILE_TEST # Until the CoreSight TRBE driver changes are in
+	depends on CORESIGHT_TRBE
+	default y
+	select ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
+	help
+	  This option adds the workaround for ARM Neoverse-N2 erratum 2253138.
+
+	  Affected Neoverse-N2 cores might write to an out-of-range address, not reserved
+	  for TRBE. Under some conditions, the TRBE might generate a write to the next
+	  virtually addressed page following the last page of the TRBE address space
+	  (i.e., the TRBLIMITR_EL1.LIMIT), instead of wrapping around to the base.
+
+	  Work around this in the driver by always making sure that there is a
+	  page beyond the TRBLIMITR_EL1.LIMIT, within the space allowed for the TRBE.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2224489
+	bool "Cortex-A710: 2224489: workaround TRBE writing to address out-of-range"
+	depends on COMPILE_TEST # Until the CoreSight TRBE driver changes are in
+	depends on CORESIGHT_TRBE
+	default y
+	select ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
+	help
+	  This option adds the workaround for ARM Cortex-A710 erratum 2224489.
+
+	  Affected Cortex-A710 cores might write to an out-of-range address, not reserved
+	  for TRBE. Under some conditions, the TRBE might generate a write to the next
+	  virtually addressed page following the last page of the TRBE address space
+	  (i.e., the TRBLIMITR_EL1.LIMIT), instead of wrapping around to the base.
+
+	  Work around this in the driver by always making sure that there is a
+	  page beyond the TRBLIMITR_EL1.LIMIT, within the space allowed for the TRBE.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_3194386
+	bool "Cortex-*/Neoverse-*: workaround for MSR SSBS not self-synchronizing"
+	default y
+	help
+	  This option adds the workaround for the following errata:
+
+	  * ARM Cortex-A76 erratum 3324349
+	  * ARM Cortex-A77 erratum 3324348
+	  * ARM Cortex-A78 erratum 3324344
+	  * ARM Cortex-A78C erratum 3324346
+	  * ARM Cortex-A78C erratum 3324347
+	  * ARM Cortex-A710 erratam 3324338
+	  * ARM Cortex-A715 errartum 3456084
+	  * ARM Cortex-A720 erratum 3456091
+	  * ARM Cortex-A725 erratum 3456106
+	  * ARM Cortex-X1 erratum 3324344
+	  * ARM Cortex-X1C erratum 3324346
+	  * ARM Cortex-X2 erratum 3324338
+	  * ARM Cortex-X3 erratum 3324335
+	  * ARM Cortex-X4 erratum 3194386
+	  * ARM Cortex-X925 erratum 3324334
+	  * ARM Neoverse-N1 erratum 3324349
+	  * ARM Neoverse N2 erratum 3324339
+	  * ARM Neoverse-N3 erratum 3456111
+	  * ARM Neoverse-V1 erratum 3324341
+	  * ARM Neoverse V2 erratum 3324336
+	  * ARM Neoverse-V3 erratum 3312417
+
+	  On affected cores "MSR SSBS, #0" instructions may not affect
+	  subsequent speculative instructions, which may permit unexepected
+	  speculative store bypassing.
+
+	  Work around this problem by placing a Speculation Barrier (SB) or
+	  Instruction Synchronization Barrier (ISB) after kernel changes to
+	  SSBS. The presence of the SSBS special-purpose register is hidden
+	  from hwcaps and EL0 reads of ID_AA64PFR1_EL1, such that userspace
+	  will use the PR_SPEC_STORE_BYPASS prctl to change SSBS.
+
+	  If unsure, say Y.
+
 config CAVIUM_ERRATUM_22375
 	bool "Cavium erratum 22375, 24313"
 	default y
@@ -971,6 +1193,8 @@
 config CPU_BIG_ENDIAN
 	bool "Build big-endian kernel"
 	depends on !LD_IS_LLD || LLD_VERSION >= 130000
+	# https://github.com/llvm/llvm-project/commit/1379b150991f70a5782e9a143c2ba5308da1161c
+	depends on AS_IS_GNU || AS_VERSION >= 150000
 	help
 	  Say Y if you plan on running a kernel with a big-endian userspace.
 
@@ -1053,9 +1277,6 @@
 	def_bool y
 	depends on ARM_PMU
 
-config ARCH_HAS_FILTER_PGPROT
-	def_bool y
-
 # Supported by clang >= 7.0
 config CC_HAVE_SHADOW_CALL_STACK
 	def_bool $(cc-option, -fsanitize=shadow-call-stack -ffixed-x18)
@@ -1152,6 +1373,7 @@
 config FORCE_MAX_ZONEORDER
 	int
 	default "14" if ARM64_64K_PAGES
+	default "13" if (ARCH_THUNDER && ARM64_4K_PAGES)
 	default "12" if ARM64_16K_PAGES
 	default "11"
 	help
@@ -1184,6 +1406,15 @@
 
 	  If unsure, say Y.
 
+config MITIGATE_SPECTRE_BRANCH_HISTORY
+	bool "Mitigate Spectre style attacks against branch history" if EXPERT
+	default y
+	help
+	  Speculation attacks against some high-performance processors can
+	  make use of branch history to influence future speculation.
+	  When taking an exception from user-space, a sequence of branches
+	  or a firmware call overwrites the branch history.
+
 config RODATA_FULL_DEFAULT_ENABLED
 	bool "Apply r/o permissions of VM areas also to their linear aliases"
 	default y
@@ -1264,7 +1495,8 @@
 
 config COMPAT_VDSO
 	bool "Enable vDSO for 32-bit applications"
-	depends on !CPU_BIG_ENDIAN && "$(CROSS_COMPILE_COMPAT)" != ""
+	depends on !CPU_BIG_ENDIAN
+	depends on (CC_IS_CLANG && LD_IS_LLD) || "$(CROSS_COMPILE_COMPAT)" != ""
 	select GENERIC_COMPAT_VDSO
 	default y
 	help
@@ -1602,6 +1834,8 @@
 	depends on CC_HAS_BRANCH_PROT_PAC_RET_BTI
 	# https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94697
 	depends on !CC_IS_GCC || GCC_VERSION >= 100100
+	# https://gcc.gnu.org/bugzilla/show_bug.cgi?id=106671
+	depends on !CC_IS_GCC
 	# https://github.com/llvm/llvm-project/commit/a88c722e687e6780dcd6a58718350dc76fcc4cc9
 	depends on !CC_IS_CLANG || CLANG_VERSION >= 120000
 	depends on (!FUNCTION_GRAPH_TRACER || DYNAMIC_FTRACE_WITH_REGS)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/Kconfig.platforms
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/Kconfig.platforms
@@ -259,6 +259,7 @@
 
 config ARCH_SYNQUACER
 	bool "Socionext SynQuacer SoC Family"
+	select IRQ_FASTEOI_HIERARCHY_HANDLERS
 
 config ARCH_TEGRA
 	bool "NVIDIA Tegra SoC Family"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/Makefile
@@ -10,7 +10,7 @@
 #
 # Copyright (C) 1995-2001 by Russell King
 
-LDFLAGS_vmlinux	:=--no-undefined -X
+LDFLAGS_vmlinux	:=--no-undefined -X --pic-veneer
 
 ifeq ($(CONFIG_RELOCATABLE), y)
 # Pass --no-apply-dynamic-relocs to restore pre-binutils-2.27 behaviour
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -343,19 +343,19 @@
 	};
 
 	thermal-zones {
-		cpu-thermal-zone {
+		cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 0>;
 		};
 
-		ddr-thermal-zone {
+		ddr-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 2>;
 		};
 
-		gpu-thermal-zone {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
@@ -4,7 +4,7 @@
  */
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
@@ -40,7 +40,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "orangepi:green:status";
 			gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
@@ -200,6 +200,9 @@
 		interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */
 		vdd-supply = <&reg_dldo1>;
 		vddio-supply = <&reg_dldo1>;
+		mount-matrix = "0", "1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "1";
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
@@ -2,7 +2,7 @@
 // Copyright (C) 2020 Chen-Yu Tsai <wens@csie.org>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
@@ -69,7 +69,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -217,7 +217,7 @@
 			};
 		};
 
-		gpu_thermal {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
@@ -3,7 +3,7 @@
 // Copyright (C) 2020 Clément Péron <peron.clem@gmail.com>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "allwinner,sun50i-h6-operating-points";
 		nvmem-cells = <&cpu_speed_grade>;
 		opp-shared;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
@@ -594,7 +594,7 @@
 		};
 
 		qspi: spi@ff8d2000 {
-			compatible = "cdns,qspi-nor";
+			compatible =  "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff8d2000 0x100>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts
@@ -129,7 +129,7 @@
 	status = "okay";
 	clock-frequency = <100000>;
 	i2c-sda-falling-time-ns = <890>;  /* hcnt */
-	i2c-sdl-falling-time-ns = <890>;  /* lcnt */
+	i2c-scl-falling-time-ns = <890>;  /* lcnt */
 
 	adc@14 {
 		compatible = "lltc,ltc2497";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
@@ -162,7 +162,7 @@
 	status = "okay";
 	clock-frequency = <100000>;
 	i2c-sda-falling-time-ns = <890>;  /* hcnt */
-	i2c-sdl-falling-time-ns = <890>;  /* lcnt */
+	i2c-scl-falling-time-ns = <890>;  /* lcnt */
 
 	adc@14 {
 		compatible = "lltc,ltc2497";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
@@ -152,7 +152,7 @@
 		scpi_clocks: clocks {
 			compatible = "arm,scpi-clocks";
 
-			scpi_dvfs: clock-controller {
+			scpi_dvfs: clocks-0 {
 				compatible = "arm,scpi-dvfs-clocks";
 				#clock-cells = <1>;
 				clock-indices = <0>;
@@ -161,7 +161,7 @@
 		};
 
 		scpi_sensors: sensors {
-			compatible = "amlogic,meson-gxbb-scpi-sensors";
+			compatible = "amlogic,meson-gxbb-scpi-sensors", "arm,scpi-sensors";
 			#thermal-sensor-cells = <1>;
 		};
 	};
@@ -1885,7 +1885,7 @@
 			sd_emmc_b: sd@5000 {
 				compatible = "amlogic,meson-axg-mmc";
 				reg = <0x0 0x5000 0x0 0x800>;
-				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_B>,
 					<&clkc CLKID_SD_EMMC_B_CLK0>,
@@ -1897,7 +1897,7 @@
 			sd_emmc_c: mmc@7000 {
 				compatible = "amlogic,meson-axg-mmc";
 				reg = <0x0 0x7000 0x0 0x800>;
-				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_C>,
 					<&clkc CLKID_SD_EMMC_C_CLK0>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -58,7 +58,7 @@
 		secure-monitor = <&sm>;
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-124999998 {
@@ -107,6 +107,12 @@
 			no-map;
 		};
 
+		/* 32 MiB reserved for ARM Trusted Firmware (BL32) */
+		secmon_reserved_bl32: secmon@5300000 {
+			reg = <0x0 0x05300000 0x0 0x2000000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -1604,10 +1610,9 @@
 
 			dmc: bus@38000 {
 				compatible = "simple-bus";
-				reg = <0x0 0x38000 0x0 0x400>;
 				#address-cells = <2>;
 				#size-cells = <2>;
-				ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>;
+				ranges = <0x0 0x0 0x0 0x38000 0x0 0x2000>;
 
 				canvas: video-lut@48 {
 					compatible = "amlogic,canvas";
@@ -1727,7 +1732,7 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					internal_ephy: ethernet_phy@8 {
+					internal_ephy: ethernet-phy@8 {
 						compatible = "ethernet-phy-id0180.3301",
 							     "ethernet-phy-ieee802.3-c22";
 						interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -2324,7 +2329,7 @@
 		sd_emmc_a: sd@ffe03000 {
 			compatible = "amlogic,meson-axg-mmc";
 			reg = <0x0 0xffe03000 0x0 0x800>;
-			interrupts = <GIC_SPI 189 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 			clocks = <&clkc CLKID_SD_EMMC_A>,
 				 <&clkc CLKID_SD_EMMC_A_CLK0>,
@@ -2336,7 +2341,7 @@
 		sd_emmc_b: sd@ffe05000 {
 			compatible = "amlogic,meson-axg-mmc";
 			reg = <0x0 0xffe05000 0x0 0x800>;
-			interrupts = <GIC_SPI 190 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 			clocks = <&clkc CLKID_SD_EMMC_B>,
 				 <&clkc CLKID_SD_EMMC_B_CLK0>,
@@ -2348,7 +2353,7 @@
 		sd_emmc_c: mmc@ffe07000 {
 			compatible = "amlogic,meson-axg-mmc";
 			reg = <0x0 0xffe07000 0x0 0x800>;
-			interrupts = <GIC_SPI 191 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 			clocks = <&clkc CLKID_SD_EMMC_C>,
 				 <&clkc CLKID_SD_EMMC_C_CLK0>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -139,7 +139,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -157,14 +157,6 @@
 		regulator-always-on;
 	};
 
-	reserved-memory {
-		/* TEE Reserved Memory */
-		bl32_reserved: bl32@5000000 {
-			reg = <0x0 0x05300000 0x0 0x2000000>;
-			no-map;
-		};
-	};
-
 	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -139,7 +139,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -139,7 +139,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -57,26 +57,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <666666666>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <731000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi
@@ -11,26 +11,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <761000>;
@@ -71,26 +51,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <731000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi
@@ -18,7 +18,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_ab 0 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -37,7 +37,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&vsys_3v3>;
+		pwm-supply = <&vsys_3v3>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -17,7 +17,7 @@
 		rtc1 = &vrtc;
 	};
 
-	dioo2133: audio-amplifier-0 {
+	dio2133: audio-amplifier-0 {
 		compatible = "simple-audio-amplifier";
 		enable-gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
 		VCC-supply = <&vcc_5v>;
@@ -130,7 +130,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_ab 0 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -149,7 +149,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -217,7 +217,7 @@
 		audio-widgets = "Line", "Lineout";
 		audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>,
 				 <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>,
-				 <&dioo2133>;
+				 <&dio2133>;
 		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
 				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
 				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
@@ -607,7 +607,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	mx25u64: spi-flash@0 {
+	mx25u64: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "mxicy,mx25u6435f", "jedec,spi-nor";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi
@@ -11,26 +11,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <731000>;
@@ -76,26 +56,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <751000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <751000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <751000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <751000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <771000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
@@ -96,7 +96,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_ab 0 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -115,7 +115,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
@@ -17,7 +17,7 @@
 		io-channel-names = "buttons";
 		keyup-threshold-microvolt = <1800000>;
 
-		update-button {
+		button-update {
 			label = "update";
 			linux,code = <KEY_VENDOR>;
 			press-threshold-microvolt = <1300000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -49,6 +49,12 @@
 			no-map;
 		};
 
+		/* 32 MiB reserved for ARM Trusted Firmware (BL32) */
+		secmon_reserved_bl32: secmon@5300000 {
+			reg = <0x0 0x05300000 0x0 0x2000000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -226,7 +232,7 @@
 			reg = <0x14 0x10>;
 		};
 
-		eth_mac: eth_mac@34 {
+		eth_mac: eth-mac@34 {
 			reg = <0x34 0x10>;
 		};
 
@@ -243,7 +249,7 @@
 		scpi_clocks: clocks {
 			compatible = "arm,scpi-clocks";
 
-			scpi_dvfs: scpi_clocks@0 {
+			scpi_dvfs: clocks-0 {
 				compatible = "arm,scpi-dvfs-clocks";
 				#clock-cells = <1>;
 				clock-indices = <0>;
@@ -525,7 +531,7 @@
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
 
-			hwrng: rng {
+			hwrng: rng@0 {
 				compatible = "amlogic,meson-rng";
 				reg = <0x0 0x0 0x0 0x4>;
 			};
@@ -596,21 +602,21 @@
 			sd_emmc_a: mmc@70000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
 				reg = <0x0 0x70000 0x0 0x800>;
-				interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
 
 			sd_emmc_b: mmc@72000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
 				reg = <0x0 0x72000 0x0 0x800>;
-				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
 
 			sd_emmc_c: mmc@74000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
 				reg = <0x0 0x74000 0x0 0x800>;
-				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts
@@ -16,7 +16,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		status {
+		led {
 			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			color = <LED_COLOR_ID_RED>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
@@ -6,6 +6,7 @@
  */
 
 #include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	aliases {
@@ -64,6 +65,7 @@
 		regulator-name = "VDDIO_AO18";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
 	};
 
 	vcc_3v3: regulator-vcc_3v3 {
@@ -161,6 +163,7 @@
 	status = "okay";
 	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
 	pinctrl-names = "default";
+	hdmi-supply = <&vddio_ao18>;
 };
 
 &hdmi_tx_tmds_port {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -311,8 +311,8 @@
 		 <&reset RESET_HDMI_SYSTEM_RESET>,
 		 <&reset RESET_HDMI_TX>;
 	reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
-	clocks = <&clkc CLKID_HDMI_PCLK>,
-		 <&clkc CLKID_CLK81>,
+	clocks = <&clkc CLKID_HDMI>,
+		 <&clkc CLKID_HDMI_PCLK>,
 		 <&clkc CLKID_GCLK_VENCI_INT0>;
 	clock-names = "isfr", "iahb", "venci";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-phicomm-n1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-phicomm-n1.dts
@@ -18,7 +18,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led {
 			label = "n1:white:status";
 			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
@@ -79,6 +79,5 @@
 		enable-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
 		max-speed = <2000000>;
 		clocks = <&wifi32k>;
-		clock-names = "lpo";
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -323,8 +323,8 @@
 		 <&reset RESET_HDMI_SYSTEM_RESET>,
 		 <&reset RESET_HDMI_TX>;
 	reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
-	clocks = <&clkc CLKID_HDMI_PCLK>,
-		 <&clkc CLKID_CLK81>,
+	clocks = <&clkc CLKID_HDMI>,
+		 <&clkc CLKID_HDMI_PCLK>,
 		 <&clkc CLKID_GCLK_VENCI_INT0>;
 	clock-names = "isfr", "iahb", "venci";
 };
@@ -759,7 +759,7 @@
 		};
 	};
 
-	eth-phy-mux {
+	eth-phy-mux@55c {
 		compatible = "mdio-mux-mmioreg", "mdio-mux";
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -17,13 +17,13 @@
 	compatible = "bananapi,bpi-m5", "amlogic,sm1";
 	model = "Banana Pi BPI-M5";
 
-	adc_keys {
+	adc-keys {
 		compatible = "adc-keys";
 		io-channels = <&saradc 2>;
 		io-channel-names = "buttons";
 		keyup-threshold-microvolt = <1800000>;
 
-		key {
+		button-sw3 {
 			label = "SW3";
 			linux,code = <BTN_3>;
 			press-threshold-microvolt = <1700000>;
@@ -123,7 +123,7 @@
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 
-		enable-gpio = <&gpio GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 
@@ -173,7 +173,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -437,6 +437,7 @@
 		"",
 		"eMMC_RST#", /* BOOT_12 */
 		"eMMC_DS", /* BOOT_13 */
+		"", "",
 		/* GPIOC */
 		"SD_D0_B", /* GPIOC_0 */
 		"SD_D1_B", /* GPIOC_1 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
@@ -24,7 +24,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&vsys_3v3>;
+		pwm-supply = <&vsys_3v3>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
@@ -76,9 +76,17 @@
 };
 
 &cpu_thermal {
+	trips {
+		cpu_active: cpu-active {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "active";
+		};
+	};
+
 	cooling-maps {
 		map {
-			trip = <&cpu_passive>;
+			trip = <&cpu_active>;
 			cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
@@ -48,7 +48,7 @@
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc_5v>;
 
-		enable-gpio = <&gpio GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 
@@ -116,7 +116,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -263,6 +263,10 @@
 		reg = <0>;
 		max-speed = <1000>;
 
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
 		interrupt-parent = <&gpio_intc>;
 		/* MAC_INTR on GPIOZ_14 */
 		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
@@ -185,7 +185,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1500 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -203,14 +203,6 @@
 		regulator-always-on;
 	};
 
-	reserved-memory {
-		/* TEE Reserved Memory */
-		bl32_reserved: bl32@5000000 {
-			reg = <0x0 0x05300000 0x0 0x2000000>;
-			no-map;
-		};
-	};
-
 	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
@@ -95,26 +95,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <730000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <730000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <730000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <666666666>;
-			opp-microvolt = <750000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <770000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/arm/juno-base.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/arm/juno-base.dtsi
@@ -26,7 +26,8 @@
 		compatible = "arm,mhu", "arm,primecell";
 		reg = <0x0 0x2b1f0000 0x0 0x1000>;
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		#mbox-cells = <1>;
 		clocks = <&soc_refclk100mhz>;
 		clock-names = "apb_pclk";
@@ -543,8 +544,7 @@
 			 <0x02000000 0x00 0x50000000 0x00 0x50000000 0x0 0x08000000>,
 			 <0x42000000 0x40 0x00000000 0x40 0x00000000 0x1 0x00000000>;
 		/* Standard AXI Translation entries as programmed by EDK2 */
-		dma-ranges = <0x02000000 0x0 0x2c1c0000 0x0 0x2c1c0000 0x0 0x00040000>,
-			     <0x02000000 0x0 0x80000000 0x0 0x80000000 0x0 0x80000000>,
+		dma-ranges = <0x02000000 0x0 0x80000000 0x0 0x80000000 0x0 0x80000000>,
 			     <0x43000000 0x8 0x00000000 0x8 0x00000000 0x2 0x00000000>;
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 7>;
@@ -597,12 +597,26 @@
 			polling-delay = <1000>;
 			polling-delay-passive = <100>;
 			thermal-sensors = <&scpi_sensors0 0>;
+			trips {
+				pmic_crit0: trip0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
 		};
 
 		soc {
 			polling-delay = <1000>;
 			polling-delay-passive = <100>;
 			thermal-sensors = <&scpi_sensors0 3>;
+			trips {
+				soc_crit0: trip0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
 		};
 
 		big_cluster_thermal_zone: big-cluster {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/Makefile
@@ -6,6 +6,6 @@
 			      bcm2837-rpi-3-b-plus.dtb \
 			      bcm2837-rpi-cm3-io3.dtb
 
-subdir-y	+= bcm4908
+subdir-y	+= bcmbca
 subdir-y	+= northstar2
 subdir-y	+= stingray
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_BCMBCA) += \
+				bcm4906-netgear-r8000p.dtb \
+				bcm4906-tplink-archer-c2300-v1.dtb \
+				bcm4908-asus-gt-ac5300.dtb \
+				bcm4908-netgear-raxe500.dtb \
+				bcm4912-asus-gt-ax6000.dtb \
+				bcm94912.dtb \
+				bcm963158.dtb \
+				bcm96858.dtb
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-netgear-r8000p.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-netgear-r8000p.dts
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "bcm4906.dtsi"
+
+/ {
+	compatible = "netgear,r8000p", "brcm,bcm4906", "brcm,bcm4908";
+	model = "Netgear R8000P";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power-white {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power-amber {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wps {
+			function = LED_FUNCTION_WPS;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2ghz {
+			function = "2ghz";
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz-1 {
+			function = "5ghz-1";
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz-2 {
+			function = "5ghz-2";
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			function = "usb2";
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3 {
+			function = "usb3";
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wifi {
+			function = "wifi";
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 56 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&enet {
+	nvmem-cells = <&base_mac_addr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&usb_phy {
+	brcm,ioc = <1>;
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan4";
+	};
+
+	port@1 {
+		label = "lan3";
+	};
+
+	port@2 {
+		label = "lan2";
+	};
+
+	port@3 {
+		label = "lan1";
+	};
+
+	port@7 {
+		reg = <7>;
+		phy-mode = "internal";
+		phy-handle = <&phy12>;
+		label = "wan";
+	};
+};
+
+&nandcs {
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	nand-on-flash-bbt;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			compatible = "nvmem-cells";
+			label = "cferom";
+			reg = <0x0 0x100000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x0 0x100000>;
+
+			base_mac_addr: mac@106a0 {
+				reg = <0x106a0 0x6>;
+			};
+		};
+
+		partition@100000 {
+			compatible = "brcm,bcm4908-firmware";
+			label = "firmware";
+			reg = <0x100000 0x4400000>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-tplink-archer-c2300-v1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-tplink-archer-c2300-v1.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "bcm4906.dtsi"
+
+/ {
+	compatible = "tplink,archer-c2300-v1", "brcm,bcm4906", "brcm,bcm4908";
+	model = "TP-Link Archer C2300 V1";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2ghz {
+			function = "2ghz";
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			function = "5ghz";
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan-amber {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-blue {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan {
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wps {
+			function = LED_FUNCTION_WPS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			function = "usb2";
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3 {
+			function = "usbd3";
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-brightness {
+			function = LED_FUNCTION_BACKLIGHT;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		brightness {
+			label = "LEDs";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb_phy {
+	brcm,ioc = <1>;
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan4";
+	};
+
+	port@1 {
+		label = "lan3";
+	};
+
+	port@2 {
+		label = "lan2";
+	};
+
+	port@3 {
+		label = "lan1";
+	};
+
+	port@7 {
+		reg = <7>;
+		phy-mode = "internal";
+		phy-handle = <&phy12>;
+		label = "wan";
+	};
+};
+
+&nandcs {
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	nand-on-flash-bbt;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	partitions {
+		compatible = "brcm,bcm4908-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "cferom";
+			reg = <0x0 0x100000>;
+		};
+
+		partition@100000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x100000 0x3900000>;
+		};
+
+		partition@5800000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x3a00000 0x3900000>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "bcm4908.dtsi"
+
+/ {
+	cpus {
+		/delete-node/ cpu@2;
+
+		/delete-node/ cpu@3;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dts
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "bcm4908.dtsi"
+
+/ {
+	compatible = "asus,gt-ac5300", "brcm,bcm4908";
+	model = "Asus GT-AC5300";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x40000000>;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		wifi {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+		};
+
+		brightness {
+			label = "LEDs";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&enet {
+	nvmem-cells = <&base_mac_addr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&usb_phy {
+	brcm,ioc = <1>;
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan2";
+	};
+
+	port@1 {
+		label = "lan1";
+	};
+
+	port@2 {
+		label = "lan6";
+	};
+
+	port@3 {
+		label = "lan5";
+	};
+
+	/* External BCM53134S switch */
+	port@7 {
+		label = "sw";
+		reg = <7>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+};
+
+&mdio {
+	/* lan8 */
+	ethernet-phy@0 {
+		reg = <0>;
+	};
+
+	/* lan7 */
+	ethernet-phy@1 {
+		reg = <1>;
+	};
+
+	/* lan4 */
+	ethernet-phy@2 {
+		reg = <2>;
+	};
+
+	/* lan3 */
+	ethernet-phy@3 {
+		reg = <3>;
+	};
+};
+
+&nandcs {
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	nand-on-flash-bbt;
+	brcm,nand-has-wp;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	partitions {
+		compatible = "brcm,bcm4908-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			compatible = "nvmem-cells";
+			label = "cferom";
+			reg = <0x0 0x100000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x0 0x100000>;
+
+			base_mac_addr: mac@106a0 {
+				reg = <0x106a0 0x6>;
+			};
+		};
+
+		partition@100000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x100000 0x5700000>;
+		};
+
+		partition@5800000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x5800000 0x5700000>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-netgear-raxe500.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-netgear-raxe500.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "bcm4908.dtsi"
+
+/ {
+	compatible = "netgear,raxe500", "brcm,bcm4908";
+	model = "Netgear RAXE500";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x40000000>;
+	};
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan4";
+	};
+
+	port@1 {
+		label = "lan3";
+	};
+
+	port@2 {
+		label = "lan2";
+	};
+
+	port@3 {
+		label = "lan1";
+	};
+
+	port@7 {
+		reg = <7>;
+		phy-mode = "internal";
+		phy-handle = <&phy12>;
+		label = "wan";
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
@@ -0,0 +1,336 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/soc/bcm-pmb.h>
+
+/dts-v1/;
+
+/ {
+	interrupt-parent = <&gic>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x81000000 0x4000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+			      <0x2000 0x2000>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	clocks {
+		periph_clk: periph_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x80000000 0x281000>;
+
+		enet: ethernet@2000 {
+			compatible = "brcm,bcm4908-enet";
+			reg = <0x2000 0x1000>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
+		};
+
+		usb_phy: usb-phy@c200 {
+			compatible = "brcm,bcm4908-usb-phy";
+			reg = <0xc200 0x100>;
+			reg-names = "ctrl";
+			power-domains = <&pmb BCM_PMB_HOST_USB>;
+			dr_mode = "host";
+			brcm,has-xhci;
+			brcm,has-eohci;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ehci: usb@c300 {
+			compatible = "generic-ehci";
+			reg = <0xc300 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb_phy PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		ohci: usb@c400 {
+			compatible = "generic-ohci";
+			reg = <0xc400 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb_phy PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		xhci: usb@d000 {
+			compatible = "generic-xhci";
+			reg = <0xd000 0x8c8>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb_phy PHY_TYPE_USB3>;
+			status = "disabled";
+		};
+
+		bus@80000 {
+			compatible = "simple-bus";
+			#size-cells = <1>;
+			#address-cells = <1>;
+			ranges = <0 0x80000 0x50000>;
+
+			ethernet-switch@0 {
+				compatible = "brcm,bcm4908-switch";
+				reg = <0x0 0x40000>,
+				      <0x40000 0x110>,
+				      <0x40340 0x30>,
+				      <0x40380 0x30>,
+				      <0x40600 0x34>,
+				      <0x40800 0x208>;
+				reg-names = "core", "reg", "intrl2_0",
+					    "intrl2_1", "fcb", "acb";
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+				brcm,num-gphy = <5>;
+				brcm,num-rgmii-ports = <2>;
+
+				ports: ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						phy-mode = "internal";
+						phy-handle = <&phy8>;
+					};
+
+					port@1 {
+						reg = <1>;
+						phy-mode = "internal";
+						phy-handle = <&phy9>;
+					};
+
+					port@2 {
+						reg = <2>;
+						phy-mode = "internal";
+						phy-handle = <&phy10>;
+					};
+
+					port@3 {
+						reg = <3>;
+						phy-mode = "internal";
+						phy-handle = <&phy11>;
+					};
+
+					port@8 {
+						reg = <8>;
+						phy-mode = "internal";
+						ethernet = <&enet>;
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+
+			mdio: mdio@405c0 {
+				compatible = "brcm,unimac-mdio";
+				reg = <0x405c0 0x8>;
+				reg-names = "mdio";
+				#size-cells = <0>;
+				#address-cells = <1>;
+
+				phy8: ethernet-phy@8 {
+					reg = <8>;
+				};
+
+				phy9: ethernet-phy@9 {
+					reg = <9>;
+				};
+
+				phy10: ethernet-phy@a {
+					reg = <10>;
+				};
+
+				phy11: ethernet-phy@b {
+					reg = <11>;
+				};
+
+				phy12: ethernet-phy@c {
+					reg = <12>;
+				};
+			};
+		};
+
+		procmon: bus@280000 {
+			compatible = "simple-bus";
+			reg = <0x280000 0x1000>;
+			ranges;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pmb: power-controller@2800c0 {
+				compatible = "brcm,bcm4908-pmb";
+				reg = <0x2800c0 0x40>;
+				#power-domain-cells = <1>;
+			};
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0xff800000 0x3000>;
+
+		twd: timer-mfd@400 {
+			compatible = "brcm,bcm4908-twd", "simple-mfd", "syscon";
+			reg = <0x400 0x4c>;
+		};
+
+		gpio0: gpio-controller@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg-names = "dirout", "dat";
+			reg = <0x500 0x28>, <0x528 0x28>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x18>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "okay";
+		};
+
+		nand@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "nand_ctlrdy";
+			status = "okay";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		misc@2600 {
+			compatible = "brcm,misc", "simple-mfd";
+			reg = <0x2600 0xe4>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00 0x2600 0xe4>;
+
+			reset-controller@2644 {
+				compatible = "brcm,bcm4908-misc-pcie-reset";
+				reg = <0x44 0x04>;
+				#reset-cells = <1>;
+			};
+		};
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&twd>;
+		offset = <0x34>;
+		mask = <1>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912-asus-gt-ax6000.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912-asus-gt-ax6000.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "bcm4912.dtsi"
+
+/ {
+	compatible = "asus,gt-ax6000", "brcm,bcm4912", "brcm,bcmbca";
+	model = "Asus GT-AX6000";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x40000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm4912", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm63158", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm6858", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk:periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>, /* GICD */
+				<0x2000 0x2000>, /* GICC */
+				<0x4000 0x2000>, /* GICH */
+				<0x6000 0x2000>; /* GICV */
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x62000>;
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x18>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm94912.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm94912.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm4912.dtsi"
+
+/ {
+	model = "Broadcom BCM94912 Reference Board";
+	compatible = "brcm,bcm94912", "brcm,bcm4912", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63158.dtsi"
+
+/ {
+	model = "Broadcom BCM963158 Reference Board";
+	compatible = "brcm,bcm963158", "brcm,bcm63158", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/bcmbca/bcm96858.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/bcmbca/bcm96858.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6858.dtsi"
+
+/ {
+	model = "Broadcom BCM96858 Reference Board";
+	compatible = "brcm,bcm96858", "brcm,bcm6858", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts
@@ -111,8 +111,8 @@
 		compatible = "silabs,si3226x";
 		reg = <0>;
 		spi-max-frequency = <5000000>;
-		spi-cpha = <1>;
-		spi-cpol = <1>;
+		spi-cpha;
+		spi-cpol;
 		pl022,hierarchy = <0>;
 		pl022,interface = <0>;
 		pl022,slave-tx-disable = <0>;
@@ -135,8 +135,8 @@
 		at25,byte-len = <0x8000>;
 		at25,addr-mode = <2>;
 		at25,page-size = <64>;
-		spi-cpha = <1>;
-		spi-cpol = <1>;
+		spi-cpha;
+		spi-cpol;
 		pl022,hierarchy = <0>;
 		pl022,interface = <0>;
 		pl022,slave-tx-disable = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
@@ -687,7 +687,7 @@
 			};
 		};
 
-		sata: ahci@663f2000 {
+		sata: sata@663f2000 {
 			compatible = "brcm,iproc-ahci", "generic-ahci";
 			reg = <0x663f2000 0x1000>;
 			dma-coherent;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
@@ -110,7 +110,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
@@ -15,6 +15,7 @@
 	compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
 
 	aliases {
+		serial0 = &duart0;
 		mmc0 = &esdhc0;
 		mmc1 = &esdhc1;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -272,11 +272,6 @@
 				vcc-supply = <&sb_3v3>;
 			};
 
-			rtc@51 {
-				compatible = "nxp,pcf2129";
-				reg = <0x51>;
-			};
-
 			eeprom@56 {
 				compatible = "atmel,24c512";
 				reg = <0x56>;
@@ -318,6 +313,15 @@
 
 };
 
+&i2c1 {
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf2129";
+		reg = <0x51>;
+	};
+};
+
 &enetc_port1 {
 	phy-handle = <&qds_phy1>;
 	phy-connection-type = "rgmii-id";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
@@ -70,7 +70,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
@@ -536,9 +536,9 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(1)>;
-			dmas = <&edma0 1 39>,
-			       <&edma0 1 38>;
-			dma-names = "tx", "rx";
+			dmas = <&edma0 1 38>,
+			       <&edma0 1 39>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -76,7 +76,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -499,9 +499,9 @@
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(2)>;
-			dmas = <&edma0 1 39>,
-			       <&edma0 1 38>;
-			dma-names = "tx", "rx";
+			dmas = <&edma0 1 38>,
+			       <&edma0 1 39>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts
@@ -53,7 +53,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -136,7 +136,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
@@ -38,7 +38,6 @@
 		powerdn {
 			label = "External Power Down";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-			interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>;
 			linux,code = <KEY_POWER>;
 		};
 
@@ -46,7 +45,6 @@
 		admin {
 			label = "ADMIN button";
 			gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
-			interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>;
 			linux,code = <KEY_WPS_BUTTON>;
 		};
 	};
@@ -247,7 +245,7 @@
 &i2c3 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9540";
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -758,6 +758,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(1)>;
 			status = "disabled";
 		};
 
@@ -767,6 +770,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(1)>;
 			status = "disabled";
 		};
 
@@ -847,7 +853,7 @@
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -857,7 +863,7 @@
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -867,7 +873,7 @@
 		};
 
 		cluster1_core2_watchdog: wdt@c020000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc020000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -877,7 +883,7 @@
 		};
 
 		cluster1_core3_watchdog: wdt@c030000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc030000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -887,7 +893,7 @@
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -897,7 +903,7 @@
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -907,7 +913,7 @@
 		};
 
 		cluster2_core2_watchdog: wdt@c120000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc120000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -917,7 +923,7 @@
 		};
 
 		cluster2_core3_watchdog: wdt@c130000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc130000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
@@ -44,7 +44,7 @@
 
 &i2c0 {
 	status = "okay";
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
@@ -44,7 +44,7 @@
 
 &i2c0 {
 	status = "okay";
-	pca9547@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9547";
 		reg = <0x75>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -387,7 +387,7 @@
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -397,7 +397,7 @@
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -407,7 +407,7 @@
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -417,7 +417,7 @@
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -427,7 +427,7 @@
 		};
 
 		cluster3_core0_watchdog: wdt@c200000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc200000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -437,7 +437,7 @@
 		};
 
 		cluster3_core1_watchdog: wdt@c210000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc210000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -447,7 +447,7 @@
 		};
 
 		cluster4_core0_watchdog: wdt@c300000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc300000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -457,7 +457,7 @@
 		};
 
 		cluster4_core1_watchdog: wdt@c310000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc310000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -525,6 +525,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -534,6 +537,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -1173,26 +1179,34 @@
 			dma-coherent;
 		};
 
-		usb0: usb@3100000 {
-			status = "disabled";
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3100000 0x0 0x10000>;
-			interrupts = <0 80 0x4>; /* Level high type */
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-		};
-
-		usb1: usb@3110000 {
-			status = "disabled";
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3110000 0x0 0x10000>;
-			interrupts = <0 81 0x4>; /* Level high type */
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+		bus: bus {
+			#address-cells = <2>;
+			#size-cells = <2>;
+			compatible = "simple-bus";
+			ranges;
+			dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x00000000>;
+
+			usb0: usb@3100000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x3100000 0x0 0x10000>;
+				interrupts = <0 80 0x4>; /* Level high type */
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				status = "disabled";
+			};
+
+			usb1: usb@3110000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x3110000 0x0 0x10000>;
+				interrupts = <0 81 0x4>; /* Level high type */
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				status = "disabled";
+			};
 		};
 
 		ccn@4000000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi
@@ -54,7 +54,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -719,7 +719,7 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>;
-			scl-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+			scl-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
 			status = "disabled";
 		};
 
@@ -768,7 +768,7 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>;
-			scl-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+			scl-gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
 			status = "disabled";
 		};
 
@@ -1369,6 +1369,9 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			little-endian;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -1379,6 +1382,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
@@ -40,7 +40,7 @@
 		clocks = <&sdhc0_lpcg IMX_LPCG_CLK_4>,
 			 <&sdhc0_lpcg IMX_LPCG_CLK_5>,
 			 <&sdhc0_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "ipg", "per", "ahb";
+		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_0>;
 		status = "disabled";
 	};
@@ -51,7 +51,7 @@
 		clocks = <&sdhc1_lpcg IMX_LPCG_CLK_4>,
 			 <&sdhc1_lpcg IMX_LPCG_CLK_5>,
 			 <&sdhc1_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "ipg", "per", "ahb";
+		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_1>;
 		fsl,tuning-start-tap = <20>;
 		fsl,tuning-step= <2>;
@@ -64,7 +64,7 @@
 		clocks = <&sdhc2_lpcg IMX_LPCG_CLK_4>,
 			 <&sdhc2_lpcg IMX_LPCG_CLK_5>,
 			 <&sdhc2_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "ipg", "per", "ahb";
+		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_2>;
 		status = "disabled";
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
@@ -26,6 +26,8 @@
 		clocks = <&uart0_lpcg IMX_LPCG_CLK_4>,
 			 <&uart0_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "baud";
+		assigned-clocks = <&clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <80000000>;
 		power-domains = <&pd IMX_SC_R_UART_0>;
 		status = "disabled";
 	};
@@ -36,6 +38,8 @@
 		clocks = <&uart1_lpcg IMX_LPCG_CLK_4>,
 			 <&uart1_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "baud";
+		assigned-clocks = <&clk IMX_SC_R_UART_1 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <80000000>;
 		power-domains = <&pd IMX_SC_R_UART_1>;
 		status = "disabled";
 	};
@@ -46,6 +50,8 @@
 		clocks = <&uart2_lpcg IMX_LPCG_CLK_4>,
 			 <&uart2_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "baud";
+		assigned-clocks = <&clk IMX_SC_R_UART_2 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <80000000>;
 		power-domains = <&pd IMX_SC_R_UART_2>;
 		status = "disabled";
 	};
@@ -56,6 +62,8 @@
 		clocks = <&uart3_lpcg IMX_LPCG_CLK_4>,
 			 <&uart3_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "baud";
+		assigned-clocks = <&clk IMX_SC_R_UART_3 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <80000000>;
 		power-domains = <&pd IMX_SC_R_UART_3>;
 		status = "disabled";
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
@@ -70,7 +70,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom@0 {
@@ -166,6 +166,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	assigned-clocks = <&clk IMX8MM_CLK_UART3>;
 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -185,7 +186,7 @@
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
 			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13              0x41
 		>;
 	};
 
@@ -236,6 +237,8 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX	0x40
 			MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX	0x40
+			MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x40
+			MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x40
 		>;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -136,7 +136,7 @@
 		rohm,reset-snvs-powered;
 
 		#clock-cells = <0>;
-		clocks = <&osc_32k 0>;
+		clocks = <&osc_32k>;
 		clock-output-names = "clk-32k-out";
 
 		regulators {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -123,8 +123,8 @@
 
 		ethphy: ethernet-phy@0 {
 			reg = <0>;
-			reset-assert-us = <100>;
-			reset-deassert-us = <100>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
 			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -191,8 +191,10 @@
 };
 
 &usdhc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
 	vqmmc-supply = <&reg_nvcc_sd>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
@@ -275,8 +277,8 @@
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
@@ -288,19 +290,19 @@
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
@@ -312,13 +314,40 @@
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -220,8 +220,8 @@
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts
@@ -214,7 +214,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	i2cmux@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9540";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -247,7 +247,7 @@
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
 		clocks = <&clk IMX8MM_CLK_SAI1_ROOT>;
-		clock-names = "mclk1";
+		clock-names = "mclk";
 		wlf,shared-lrclk;
 		#sound-dai-cells = <0>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
@@ -601,7 +601,7 @@
 #define MX8MM_IOMUXC_UART1_RXD_GPIO5_IO22                                   0x234 0x49C 0x000 0x5 0x0
 #define MX8MM_IOMUXC_UART1_RXD_TPSMP_HDATA24                                0x234 0x49C 0x000 0x7 0x0
 #define MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX                                 0x238 0x4A0 0x000 0x0 0x0
-#define MX8MM_IOMUXC_UART1_TXD_UART1_DTE_RX                                 0x238 0x4A0 0x4F4 0x0 0x0
+#define MX8MM_IOMUXC_UART1_TXD_UART1_DTE_RX                                 0x238 0x4A0 0x4F4 0x0 0x1
 #define MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI                                  0x238 0x4A0 0x000 0x1 0x0
 #define MX8MM_IOMUXC_UART1_TXD_GPIO5_IO23                                   0x238 0x4A0 0x000 0x5 0x0
 #define MX8MM_IOMUXC_UART1_TXD_TPSMP_HDATA25                                0x238 0x4A0 0x000 0x7 0x0
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -89,12 +89,12 @@
 		pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <125>;
-		touchscreen-size-x = /bits/ 16 <4008>;
+		touchscreen-size-x = <4008>;
 		ti,y-min = /bits/ 16 <282>;
-		touchscreen-size-y = /bits/ 16 <3864>;
+		touchscreen-size-y = <3864>;
 		ti,x-plate-ohms = /bits/ 16 <180>;
-		touchscreen-max-pressure = /bits/ 16 <255>;
-		touchscreen-average-samples = /bits/ 16 <10>;
+		touchscreen-max-pressure = <255>;
+		touchscreen-average-samples = <10>;
 		ti,debounce-tol = /bits/ 16 <3>;
 		ti,debounce-rep = /bits/ 16 <1>;
 		ti,settle-delay-usec = /bits/ 16 <150>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
@@ -40,17 +40,6 @@
 		gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 		status = "okay";
 	};
-
-	reg_usb_otg1_vbus: regulator-usb-otg1 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_usb1_en>;
-		compatible = "regulator-fixed";
-		regulator-name = "usb_otg1_vbus";
-		gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
 };
 
 /* off-board header */
@@ -102,13 +91,16 @@
 };
 
 &usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
-	vbus-supply = <&reg_usb_otg1_vbus>;
+	over-current-active-low;
 	status = "okay";
 };
 
 &usbotg2 {
 	dr_mode = "host";
+	disable-over-current;
 	status = "okay";
 };
 
@@ -154,19 +146,11 @@
 		>;
 	};
 
-	pinctrl_reg_usb1_en: regusb1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x41
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
-			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
-		>;
-	};
-
 	pinctrl_spi2: spi2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0xd6
 			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
 		>;
 	};
@@ -184,4 +168,11 @@
 			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
 		>;
 	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
+		>;
+	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
@@ -139,12 +139,14 @@
 
 &usbotg1 {
 	dr_mode = "otg";
+	over-current-active-low;
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
 	dr_mode = "host";
+	disable-over-current;
 	vbus-supply = <&reg_usb_otg2_vbus>;
 	status = "okay";
 };
@@ -231,7 +233,7 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0xd6
 			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
 		>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
@@ -166,12 +166,14 @@
 
 &usbotg1 {
 	dr_mode = "otg";
+	over-current-active-low;
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
 	dr_mode = "host";
+	disable-over-current;
 	vbus-supply = <&reg_usb_otg2_vbus>;
 	status = "okay";
 };
@@ -280,7 +282,7 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0xd6
 			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
 		>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
@@ -675,6 +675,7 @@
 &usbotg2 {
 	dr_mode = "host";
 	vbus-supply = <&reg_usb2_vbus>;
+	over-current-active-low;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -366,6 +366,7 @@
 						      "pll8k", "pll11k", "clkext3";
 					dmas = <&sdma2 24 25 0x80000000>;
 					dma-names = "rx";
+					#sound-dai-cells = <0>;
 					status = "disabled";
 				};
 
@@ -530,7 +531,7 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 
-				imx8mm_uid: unique-id@410 {
+				imx8mm_uid: unique-id@4 {
 					reg = <0x4 0x8>;
 				};
 
@@ -1014,10 +1015,10 @@
 			clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
 		};
 
-		gpmi: nand-controller@33002000{
+		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx8mm-gpmi-nand", "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
@@ -81,7 +81,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom@0 {
@@ -176,6 +176,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	assigned-clocks = <&clk IMX8MN_CLK_UART3>;
 	assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -202,7 +203,7 @@
 			MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
 			MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
 			MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
+			MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x41
 		>;
 	};
 
@@ -259,6 +260,8 @@
 		fsl,pins = <
 			MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX	0x40
 			MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX	0x40
+			MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x40
+			MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x40
 		>;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -59,6 +59,10 @@
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
+
 		regulators {
 			buck1_reg: BUCK1 {
 				regulator-name = "buck1";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
@@ -70,12 +70,12 @@
 		pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <125>;
-		touchscreen-size-x = /bits/ 16 <4008>;
+		touchscreen-size-x = <4008>;
 		ti,y-min = /bits/ 16 <282>;
-		touchscreen-size-y = /bits/ 16 <3864>;
+		touchscreen-size-y = <3864>;
 		ti,x-plate-ohms = /bits/ 16 <180>;
-		touchscreen-max-pressure = /bits/ 16 <255>;
-		touchscreen-average-samples = /bits/ 16 <10>;
+		touchscreen-max-pressure = <255>;
+		touchscreen-average-samples = <10>;
 		ti,debounce-tol = /bits/ 16 <3>;
 		ti,debounce-rep = /bits/ 16 <1>;
 		ti,settle-delay-usec = /bits/ 16 <150>;
@@ -98,11 +98,17 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethphy: ethernet-phy@4 {
+		ethphy: ethernet-phy@4 { /* AR8033 or ADIN1300 */
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <4>;
 			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
+			/*
+			 * Deassert delay:
+			 * ADIN1300 requires 5ms.
+			 * AR8033   requires 1ms.
+			 */
+			reset-deassert-us = <20000>;
 		};
 	};
 };
@@ -345,7 +351,7 @@
 			MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
 			MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
-			MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x159
 		>;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mn.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mn.dtsi
@@ -263,8 +263,9 @@
 				ranges;
 
 				sai2: sai@30020000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30020000 0x10000>;
+					#sound-dai-cells = <0>;
 					interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI2_IPG>,
 						<&clk IMX8MN_CLK_DUMMY>,
@@ -277,8 +278,9 @@
 				};
 
 				sai3: sai@30030000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30030000 0x10000>;
+					#sound-dai-cells = <0>;
 					interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI3_IPG>,
 						 <&clk IMX8MN_CLK_DUMMY>,
@@ -291,8 +293,9 @@
 				};
 
 				sai5: sai@30050000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30050000 0x10000>;
+					#sound-dai-cells = <0>;
 					interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI5_IPG>,
 						 <&clk IMX8MN_CLK_DUMMY>,
@@ -307,8 +310,9 @@
 				};
 
 				sai6: sai@30060000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30060000  0x10000>;
+					#sound-dai-cells = <0>;
 					interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI6_IPG>,
 						 <&clk IMX8MN_CLK_DUMMY>,
@@ -336,6 +340,7 @@
 						      "pll8k", "pll11k", "clkext3";
 					dmas = <&sdma2 24 25 0x80000000>;
 					dma-names = "rx";
+					#sound-dai-cells = <0>;
 					status = "disabled";
 				};
 
@@ -364,8 +369,9 @@
 				};
 
 				sai7: sai@300b0000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x300b0000 0x10000>;
+					#sound-dai-cells = <0>;
 					interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI7_IPG>,
 						 <&clk IMX8MN_CLK_DUMMY>,
@@ -533,7 +539,7 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 
-				imx8mn_uid: unique-id@410 {
+				imx8mn_uid: unique-id@4 {
 					reg = <0x4 0x8>;
 				};
 
@@ -998,7 +1004,7 @@
 		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx8mn-gpmi-nand", "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -285,21 +285,21 @@
 &iomuxc {
 	pinctrl_eqos: eqosgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3
-			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3
-			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91
-			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91
-			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91
-			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91
-			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
-			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x91
-			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f
-			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f
-			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f
-			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f
-			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x1f
-			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
-			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22				0x19
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
+			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22				0x10
 		>;
 	};
 
@@ -351,21 +351,21 @@
 
 	pinctrl_gpio_led: gpioledgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x19
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x140
 		>;
 	};
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3
-			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c2
 		>;
 	};
 
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c3
-			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c3
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c2
 		>;
 	};
 
@@ -377,20 +377,20 @@
 
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x49
-			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x49
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x140
 		>;
 	};
 
 	pinctrl_usb1_vbus: usb1grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x19
+			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x10
 		>;
 	};
 
@@ -402,7 +402,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 
@@ -414,7 +414,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0
 		>;
 	};
 
@@ -426,7 +426,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0
 		>;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
@@ -116,48 +116,48 @@
 &iomuxc {
 	pinctrl_eqos: eqosgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC			0x3
-			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO			0x3
-			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0		0x91
-			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1		0x91
-			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2		0x91
-			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3		0x91
-			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
-			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x91
-			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0		0x1f
-			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1		0x1f
-			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2		0x1f
-			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3		0x1f
-			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x1f
-			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC			0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO			0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0		0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1		0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2		0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3		0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0		0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1		0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2		0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3		0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
 			MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20			0x10
 		>;
 	};
 
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c3
-			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c3
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
 		>;
 	};
 
 	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1e3
-			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1e3
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1e2
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1e2
 		>;
 	};
 
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
 		>;
 	};
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x49
-			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x49
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x40
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x40
 		>;
 	};
 
@@ -175,7 +175,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 
@@ -187,7 +187,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 
@@ -199,7 +199,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
@@ -98,7 +98,6 @@
 
 		regulators {
 			buck1: BUCK1 {
-				regulator-compatible = "BUCK1";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
@@ -107,7 +106,6 @@
 			};
 
 			buck2: BUCK2 {
-				regulator-compatible = "BUCK2";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
@@ -116,7 +114,6 @@
 			};
 
 			buck4: BUCK4 {
-				regulator-compatible = "BUCK4";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -124,7 +121,6 @@
 			};
 
 			buck5: BUCK5 {
-				regulator-compatible = "BUCK5";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -132,7 +128,6 @@
 			};
 
 			buck6: BUCK6 {
-				regulator-compatible = "BUCK6";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -140,7 +135,6 @@
 			};
 
 			ldo1: LDO1 {
-				regulator-compatible = "LDO1";
 				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -148,7 +142,6 @@
 			};
 
 			ldo2: LDO2 {
-				regulator-compatible = "LDO2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1150000>;
 				regulator-boot-on;
@@ -156,7 +149,6 @@
 			};
 
 			ldo3: LDO3 {
-				regulator-compatible = "LDO3";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -164,7 +156,6 @@
 			};
 
 			ldo4: LDO4 {
-				regulator-compatible = "LDO4";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -172,7 +163,6 @@
 			};
 
 			ldo5: LDO5 {
-				regulator-compatible = "LDO5";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -358,7 +358,7 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 
-				imx8mp_uid: unique-id@420 {
+				imx8mp_uid: unique-id@8 {
 					reg = <0x8 0x8>;
 				};
 
@@ -740,7 +740,7 @@
 				compatible = "fsl,imx8mp-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b40000 0x10000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk IMX8MP_CLK_DUMMY>,
+				clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
 					 <&clk IMX8MP_CLK_NAND_USDHC_BUS>,
 					 <&clk IMX8MP_CLK_USDHC1_ROOT>;
 				clock-names = "ipg", "ahb", "per";
@@ -754,7 +754,7 @@
 				compatible = "fsl,imx8mp-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b50000 0x10000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk IMX8MP_CLK_DUMMY>,
+				clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
 					 <&clk IMX8MP_CLK_NAND_USDHC_BUS>,
 					 <&clk IMX8MP_CLK_USDHC2_ROOT>;
 				clock-names = "ipg", "ahb", "per";
@@ -768,7 +768,7 @@
 				compatible = "fsl,imx8mp-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b60000 0x10000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk IMX8MP_CLK_DUMMY>,
+				clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
 					 <&clk IMX8MP_CLK_NAND_USDHC_BUS>,
 					 <&clk IMX8MP_CLK_USDHC3_ROOT>;
 				clock-names = "ipg", "ahb", "per";
@@ -912,7 +912,8 @@
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy0>, <&usb3_phy0>;
 				phy-names = "usb2-phy", "usb3-phy";
-				snps,dis-u2-freeclk-exists-quirk;
+				snps,gfladj-refclk-lpm-sel-quirk;
+				snps,parkmode-disable-ss-quirk;
 			};
 
 		};
@@ -953,7 +954,8 @@
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy1>, <&usb3_phy1>;
 				phy-names = "usb2-phy", "usb3-phy";
-				snps,dis-u2-freeclk-exists-quirk;
+				snps,gfladj-refclk-lpm-sel-quirk;
+				snps,parkmode-disable-ss-quirk;
 			};
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -967,6 +967,7 @@
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gauge>;
+		power-supplies = <&bq25895>;
 		maxim,over-heat-temp = <700>;
 		maxim,over-volt = <4500>;
 		maxim,rsns-microohm = <5000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -133,7 +133,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	i2cmux@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c1_pca9546>;
@@ -216,7 +216,7 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	pca9546: i2cmux@70 {
+	pca9546: i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
@@ -339,7 +339,7 @@
 	bus-width = <4>;
 	non-removable;
 	no-sd;
-	no-emmc;
+	no-mmc;
 	status = "okay";
 
 	brcmf: wifi@1 {
@@ -359,7 +359,7 @@
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	no-sdio;
-	no-emmc;
+	no-mmc;
 	disable-wp;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -524,11 +524,9 @@
 						  <&clk IMX8MQ_VIDEO_PLL1>,
 						  <&clk IMX8MQ_VIDEO_PLL1_OUT>;
 				assigned-clock-rates = <0>, <0>, <0>, <594000000>;
-				interconnects = <&noc IMX8MQ_ICM_LCDIF &noc IMX8MQ_ICS_DRAM>;
-				interconnect-names = "dram";
 				status = "disabled";
 
-				port@0 {
+				port {
 					lcdif_mipi_dsi: endpoint {
 						remote-endpoint = <&mipi_dsi_lcdif_in>;
 					};
@@ -559,7 +557,7 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 
-				imx8mq_uid: soc-uid@410 {
+				imx8mq_uid: soc-uid@4 {
 					reg = <0x4 0x8>;
 				};
 
@@ -1125,8 +1123,8 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
-						reg = <0>;
+					port@1 {
+						reg = <1>;
 
 						csi1_mipi_ep: endpoint {
 							remote-endpoint = <&csi1_ep>;
@@ -1177,8 +1175,8 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
-						reg = <0>;
+					port@1 {
+						reg = <1>;
 
 						csi2_mipi_ep: endpoint {
 							remote-endpoint = <&csi2_ep>;
@@ -1384,7 +1382,7 @@
 			phys = <&usb3_phy0>, <&usb3_phy0>;
 			phy-names = "usb2-phy", "usb3-phy";
 			power-domains = <&pgc_otg1>;
-			usb3-resume-missing-cas;
+			snps,parkmode-disable-ss-quirk;
 			status = "disabled";
 		};
 
@@ -1416,7 +1414,7 @@
 			phys = <&usb3_phy1>, <&usb3_phy1>;
 			phy-names = "usb2-phy", "usb3-phy";
 			power-domains = <&pgc_otg2>;
-			usb3-resume-missing-cas;
+			snps,parkmode-disable-ss-quirk;
 			status = "disabled";
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -32,7 +32,7 @@
 		regulator-name = "SD1_SPWR";
 		regulator-min-microvolt = <3000000>;
 		regulator-max-microvolt = <3000000>;
-		gpio = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>;
+		gpio = <&lsio_gpio4 7 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
 };
@@ -82,8 +82,8 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	vmmc-supply = <&reg_usdhc2_vmmc>;
-	cd-gpios = <&lsio_gpio4 22 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&lsio_gpio4 21 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&lsio_gpio5 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&lsio_gpio5 21 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8qm-ss-img.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8qm-ss-img.dtsi
@@ -8,5 +8,5 @@
 };
 
 &jpegenc {
-	compatible = "nxp,imx8qm-jpgdec", "nxp,imx8qxp-jpgenc";
+	compatible = "nxp,imx8qm-jpgenc", "nxp,imx8qxp-jpgenc";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -155,7 +155,7 @@
 		};
 
 		clk: clock-controller {
-			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
+			compatible = "fsl,imx8qm-clk", "fsl,scu-clk";
 			#clock-cells = <2>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -61,7 +61,7 @@
 	pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>;
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9646", "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -1087,7 +1087,7 @@
 		};
 
 		watchdog0: watchdog@e8a06000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xe8a06000 0x0 0x1000>;
 			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3660_OSC32K>,
@@ -1096,7 +1096,7 @@
 		};
 
 		watchdog1: watchdog@e8a07000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xe8a07000 0x0 0x1000>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3660_OSC32K>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
@@ -58,7 +58,7 @@
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		reg = <0x0 0xf1001000 0x0 0x1000>,  /* GICD */
-		      <0x0 0xf1002000 0x0 0x100>;   /* GICC */
+		      <0x0 0xf1002000 0x0 0x2000>;  /* GICC */
 		#address-cells = <0>;
 		#interrupt-cells = <3>;
 		interrupt-controller;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -840,7 +840,7 @@
 		};
 
 		watchdog0: watchdog@f8005000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xf8005000 0x0 0x1000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ao_ctrl HI6220_WDT0_PCLK>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
@@ -502,7 +502,7 @@
 		};
 
 		usb0: usb@ffb00000 {
-			compatible = "snps,dwc2";
+			compatible = "intel,socfpga-agilex-hsotg", "snps,dwc2";
 			reg = <0xffb00000 0x40000>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usbphy0>;
@@ -515,7 +515,7 @@
 		};
 
 		usb1: usb@ffb40000 {
-			compatible = "snps,dwc2";
+			compatible = "intel,socfpga-agilex-hsotg", "snps,dwc2";
 			reg = <0xffb40000 0x40000>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usbphy0>;
@@ -628,7 +628,7 @@
 		};
 
 		qspi: spi@ff8d2000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff8d2000 0x100>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
@@ -71,10 +71,6 @@
 
 &spi0 {
 	flash@0 {
-		spi-max-frequency = <108000000>;
-		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
-
 		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
@@ -112,7 +108,6 @@
 
 &usb3 {
 	usb-phy = <&usb3_phy>;
-	status = "disabled";
 };
 
 &mdio {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -18,6 +18,7 @@
 
 	aliases {
 		spi0 = &spi0;
+		ethernet0 = &eth0;
 		ethernet1 = &eth1;
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
@@ -124,9 +125,12 @@
 	/delete-property/ mrvl,i2c-fast-mode;
 	status = "okay";
 
+	/* MCP7940MT-I/MNY RTC */
 	rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO2_5 */
 	};
 };
 
@@ -138,7 +142,9 @@
 	/*
 	 * U-Boot port for Turris Mox has a bug which always expects that "ranges" DT property
 	 * contains exactly 2 ranges with 3 (child) address cells, 2 (parent) address cells and
-	 * 2 size cells and also expects that the second range starts at 16 MB offset. If these
+	 * 2 size cells and also expects that the second range starts at 16 MB offset. Also it
+	 * expects that first range uses same address for PCI (child) and CPU (parent) cells (so
+	 * no remapping) and that this address is the lowest from all specified ranges. If these
 	 * conditions are not met then U-Boot crashes during loading kernel DTB file. PCIe address
 	 * space is 128 MB long, so the best split between MEM and IO is to use fixed 16 MB window
 	 * for IO and the rest 112 MB (64+32+16) for MEM, despite that maximal IO size is just 64 kB.
@@ -147,6 +153,9 @@
 	 * https://source.denx.de/u-boot/u-boot/-/commit/cb2ddb291ee6fcbddd6d8f4ff49089dfe580f5d7
 	 * https://source.denx.de/u-boot/u-boot/-/commit/c64ac3b3185aeb3846297ad7391fc6df8ecd73bf
 	 * https://source.denx.de/u-boot/u-boot/-/commit/4a82fca8e330157081fc132a591ebd99ba02ee33
+	 * Bug related to requirement of same child and parent addresses for first range is fixed
+	 * in U-Boot version 2022.04 by following commit:
+	 * https://source.denx.de/u-boot/u-boot/-/commit/1fd54253bca7d43d046bba4853fe5fafd034bc17
 	 */
 	#address-cells = <3>;
 	#size-cells = <2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -414,14 +414,14 @@
 			crypto: crypto@90000 {
 				compatible = "inside-secure,safexcel-eip97ies";
 				reg = <0x90000 0x20000>;
-				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "mem", "ring0", "ring1",
-						  "ring2", "ring3", "eip";
+					     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "ring0", "ring1", "ring2",
+						  "ring3", "eip", "mem";
 				clocks = <&nb_periph_clk 15>;
 			};
 
@@ -497,7 +497,7 @@
 			 * (totaling 127 MiB) for MEM.
 			 */
 			ranges = <0x82000000 0 0xe8000000   0 0xe8000000   0 0x07f00000   /* Port 0 MEM */
-				  0x81000000 0 0xefff0000   0 0xefff0000   0 0x00010000>; /* Port 0 IO */
+				  0x81000000 0 0x00000000   0 0xefff0000   0 0x00010000>; /* Port 0 IO */
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0 0 0 1 &pcie_intc 0>,
 					<0 0 0 2 &pcie_intc 1>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -506,14 +506,14 @@
 		CP11X_LABEL(crypto): crypto@800000 {
 			compatible = "inside-secure,safexcel-eip197b";
 			reg = <0x800000 0x200000>;
-			interrupts = <87 IRQ_TYPE_LEVEL_HIGH>,
-				<88 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts = <88 IRQ_TYPE_LEVEL_HIGH>,
 				<89 IRQ_TYPE_LEVEL_HIGH>,
 				<90 IRQ_TYPE_LEVEL_HIGH>,
 				<91 IRQ_TYPE_LEVEL_HIGH>,
-				<92 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "mem", "ring0", "ring1",
-				"ring2", "ring3", "eip";
+				<92 IRQ_TYPE_LEVEL_HIGH>,
+				<87 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ring0", "ring1", "ring2", "ring3",
+					  "eip", "mem";
 			clock-names = "core", "reg";
 			clocks = <&CP11X_LABEL(clk) 1 26>,
 				 <&CP11X_LABEL(clk) 1 17>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -107,7 +107,7 @@
 				       "mpp59", "mpp60", "mpp61";
 			marvell,function = "sdio";
 		};
-		cp0_spi0_pins: cp0-spi-pins-0 {
+		cp0_spi1_pins: cp0-spi-pins-1 {
 			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
 			marvell,function = "spi1";
 		};
@@ -149,7 +149,7 @@
 
 &cp0_spi1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cp0_spi0_pins>;
+	pinctrl-0 = <&cp0_spi1_pins>;
 	reg = <0x700680 0x50>,		/* control */
 	      <0x2000000 0x1000000>;	/* CS0 */
 	status = "okay";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
@@ -307,7 +307,7 @@
 &cp0_spi1 {
 	status = "disabled";
 	pinctrl-names = "default";
-	pinctrl-0 = <&cp0_spi0_pins>;
+	pinctrl-0 = <&cp0_spi1_pins>;
 	reg = <0x700680 0x50>;
 
 	spi-flash@0 {
@@ -371,7 +371,7 @@
 				       "mpp59", "mpp60", "mpp61";
 			marvell,function = "sdio";
 		};
-		cp0_spi0_pins: cp0-spi-pins-0 {
+		cp0_spi1_pins: cp0-spi-pins-1 {
 			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
 			marvell,function = "spi1";
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/marvell/cn9130.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/marvell/cn9130.dtsi
@@ -11,6 +11,13 @@
 	model = "Marvell Armada CN9130 SoC";
 	compatible = "marvell,cn9130", "marvell,armada-ap807-quad",
 		     "marvell,armada-ap807";
+
+	aliases {
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+	};
 };
 
 /*
@@ -35,3 +42,11 @@
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
 #undef CP11X_PCIE2_BASE
+
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
@@ -26,14 +26,14 @@
 		stdout-path = "serial0:921600n8";
 	};
 
-	cpus_fixed_vproc0: fixedregulator@0 {
+	cpus_fixed_vproc0: regulator-vproc-buck0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vproc_buck0";
 		regulator-min-microvolt = <1000000>;
 		regulator-max-microvolt = <1000000>;
 	};
 
-	cpus_fixed_vproc1: fixedregulator@1 {
+	cpus_fixed_vproc1: regulator-vproc-buck1 {
 		compatible = "regulator-fixed";
 		regulator-name = "vproc_buck1";
 		regulator-min-microvolt = <1000000>;
@@ -50,7 +50,7 @@
 		id-gpio = <&pio 14 GPIO_ACTIVE_HIGH>;
 	};
 
-	usb_p0_vbus: regulator@2 {
+	usb_p0_vbus: regulator-usb-p0-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "p0_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -59,7 +59,7 @@
 		enable-active-high;
 	};
 
-	usb_p1_vbus: regulator@3 {
+	usb_p1_vbus: regulator-usb-p1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "p1_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -68,7 +68,7 @@
 		enable-active-high;
 	};
 
-	usb_p2_vbus: regulator@4 {
+	usb_p2_vbus: regulator-usb-p2-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "p2_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -77,7 +77,7 @@
 		enable-active-high;
 	};
 
-	usb_p3_vbus: regulator@5 {
+	usb_p3_vbus: regulator-usb-p3-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "p3_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -127,7 +127,7 @@
 };
 
 &pio {
-	eth_default: eth_default {
+	eth_default: eth-default-pins {
 		tx_pins {
 			pinmux = <MT2712_PIN_71_GBE_TXD3__FUNC_GBE_TXD3>,
 				 <MT2712_PIN_72_GBE_TXD2__FUNC_GBE_TXD2>,
@@ -154,7 +154,7 @@
 		};
 	};
 
-	eth_sleep: eth_sleep {
+	eth_sleep: eth-sleep-pins {
 		tx_pins {
 			pinmux = <MT2712_PIN_71_GBE_TXD3__FUNC_GPIO71>,
 				 <MT2712_PIN_72_GBE_TXD2__FUNC_GPIO72>,
@@ -180,14 +180,14 @@
 		};
 	};
 
-	usb0_id_pins_float: usb0_iddig {
+	usb0_id_pins_float: usb0-iddig-pins {
 		pins_iddig {
 			pinmux = <MT2712_PIN_12_IDDIG_P0__FUNC_IDDIG_A>;
 			bias-pull-up;
 		};
 	};
 
-	usb1_id_pins_float: usb1_iddig {
+	usb1_id_pins_float: usb1-iddig-pins {
 		pins_iddig {
 			pinmux = <MT2712_PIN_14_IDDIG_P1__FUNC_IDDIG_B>;
 			bias-pull-up;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -160,70 +160,70 @@
 		#clock-cells = <0>;
 	};
 
-	clk26m: oscillator@0 {
+	clk26m: oscillator-26m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <26000000>;
 		clock-output-names = "clk26m";
 	};
 
-	clk32k: oscillator@1 {
+	clk32k: oscillator-32k {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
 		clock-output-names = "clk32k";
 	};
 
-	clkfpc: oscillator@2 {
+	clkfpc: oscillator-50m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
 		clock-output-names = "clkfpc";
 	};
 
-	clkaud_ext_i_0: oscillator@3 {
+	clkaud_ext_i_0: oscillator-aud0 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <6500000>;
 		clock-output-names = "clkaud_ext_i_0";
 	};
 
-	clkaud_ext_i_1: oscillator@4 {
+	clkaud_ext_i_1: oscillator-aud1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <196608000>;
 		clock-output-names = "clkaud_ext_i_1";
 	};
 
-	clkaud_ext_i_2: oscillator@5 {
+	clkaud_ext_i_2: oscillator-aud2 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <180633600>;
 		clock-output-names = "clkaud_ext_i_2";
 	};
 
-	clki2si0_mck_i: oscillator@6 {
+	clki2si0_mck_i: oscillator-i2s0 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <30000000>;
 		clock-output-names = "clki2si0_mck_i";
 	};
 
-	clki2si1_mck_i: oscillator@7 {
+	clki2si1_mck_i: oscillator-i2s1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <30000000>;
 		clock-output-names = "clki2si1_mck_i";
 	};
 
-	clki2si2_mck_i: oscillator@8 {
+	clki2si2_mck_i: oscillator-i2s2 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <30000000>;
 		clock-output-names = "clki2si2_mck_i";
 	};
 
-	clktdmin_mclk_i: oscillator@9 {
+	clktdmin_mclk_i: oscillator-mclk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <30000000>;
@@ -249,10 +249,11 @@
 		#clock-cells = <1>;
 	};
 
-	infracfg: syscon@10001000 {
+	infracfg: clock-controller@10001000 {
 		compatible = "mediatek,mt2712-infracfg", "syscon";
 		reg = <0 0x10001000 0 0x1000>;
 		#clock-cells = <1>;
+		#reset-cells = <1>;
 	};
 
 	pericfg: syscon@10003000 {
@@ -266,7 +267,7 @@
 		reg = <0 0x10005000 0 0x1000>;
 	};
 
-	pio: pinctrl@10005000 {
+	pio: pinctrl@1000b000 {
 		compatible = "mediatek,mt2712-pinctrl";
 		reg = <0 0x1000b000 0 0x1000>;
 		mediatek,pctl-regmap = <&syscfg_pctl_a>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt6779.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt6779.dtsi
@@ -88,14 +88,14 @@
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW 0>;
 	};
 
-	clk26m: oscillator@0 {
+	clk26m: oscillator-26m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <26000000>;
 		clock-output-names = "clk26m";
 	};
 
-	clk32k: oscillator@1 {
+	clk32k: oscillator-32k {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
@@ -117,7 +117,7 @@
 		compatible = "simple-bus";
 		ranges;
 
-		gic: interrupt-controller@0c000000 {
+		gic: interrupt-controller@c000000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <4>;
 			interrupt-parent = <&gic>;
@@ -138,7 +138,7 @@
 
 		};
 
-		sysirq: intpol-controller@0c53a650 {
+		sysirq: intpol-controller@c53a650 {
 			compatible = "mediatek,mt6779-sysirq",
 				     "mediatek,mt6577-sysirq";
 			interrupt-controller;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt6797.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt6797.dtsi
@@ -95,7 +95,7 @@
 		};
 	};
 
-	clk26m: oscillator@0 {
+	clk26m: oscillator-26m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <26000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
@@ -49,7 +49,7 @@
 		wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&pio 102 GPIO_ACTIVE_HIGH>;
+			gpios = <&pio 102 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -69,8 +69,9 @@
 		};
 	};
 
-	memory {
+	memory@40000000 {
 		reg = <0 0x40000000 0 0x40000000>;
+		device_type = "memory";
 	};
 
 	reg_1p8v: regulator-1p8v {
@@ -284,8 +285,8 @@
 	/* eMMC is shared pin with parallel NAND */
 	emmc_pins_default: emmc-pins-default {
 		mux {
-			function = "emmc", "emmc_rst";
-			groups = "emmc";
+			function = "emmc";
+			groups = "emmc", "emmc_rst";
 		};
 
 		/* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
@@ -55,8 +55,9 @@
 		};
 	};
 
-	memory {
+	memory@40000000 {
 		reg = <0 0x40000000 0 0x20000000>;
+		device_type = "memory";
 	};
 
 	reg_1p8v: regulator-1p8v {
@@ -248,8 +249,8 @@
 	/* eMMC is shared pin with parallel NAND */
 	emmc_pins_default: emmc-pins-default {
 		mux {
-			function = "emmc", "emmc_rst";
-			groups = "emmc";
+			function = "emmc";
+			groups = "emmc", "emmc_rst";
 		};
 
 		/* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -244,7 +244,7 @@
 		clock-names = "hif_sel";
 	};
 
-	cir: cir@10009000 {
+	cir: ir-receiver@10009000 {
 		compatible = "mediatek,mt7622-cir";
 		reg = <0 0x10009000 0 0x1000>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_LOW>;
@@ -275,16 +275,14 @@
 		};
 	};
 
-	apmixedsys: apmixedsys@10209000 {
-		compatible = "mediatek,mt7622-apmixedsys",
-			     "syscon";
+	apmixedsys: clock-controller@10209000 {
+		compatible = "mediatek,mt7622-apmixedsys";
 		reg = <0 0x10209000 0 0x1000>;
 		#clock-cells = <1>;
 	};
 
-	topckgen: topckgen@10210000 {
-		compatible = "mediatek,mt7622-topckgen",
-			     "syscon";
+	topckgen: clock-controller@10210000 {
+		compatible = "mediatek,mt7622-topckgen";
 		reg = <0 0x10210000 0 0x1000>;
 		#clock-cells = <1>;
 	};
@@ -357,7 +355,7 @@
 		};
 
 		cci_control2: slave-if@5000 {
-			compatible = "arm,cci-400-ctrl-if";
+			compatible = "arm,cci-400-ctrl-if", "syscon";
 			interface-type = "ace";
 			reg = <0x5000 0x1000>;
 		};
@@ -428,6 +426,7 @@
 	pwm: pwm@11006000 {
 		compatible = "mediatek,mt7622-pwm";
 		reg = <0 0x11006000 0 0x1000>;
+		#pwm-cells = <2>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&topckgen CLK_TOP_PWM_SEL>,
 			 <&pericfg CLK_PERI_PWM_PD>,
@@ -506,7 +505,6 @@
 			 <&pericfg CLK_PERI_AUXADC_PD>;
 		clock-names = "therm", "auxadc";
 		resets = <&pericfg MT7622_PERI_THERM_SW_RST>;
-		reset-names = "therm";
 		mediatek,auxadc = <&auxadc>;
 		mediatek,apmixedsys = <&apmixedsys>;
 		nvmem-cells = <&thermal_calibration>;
@@ -714,9 +712,8 @@
 		power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
 	};
 
-	ssusbsys: ssusbsys@1a000000 {
-		compatible = "mediatek,mt7622-ssusbsys",
-			     "syscon";
+	ssusbsys: clock-controller@1a000000 {
+		compatible = "mediatek,mt7622-ssusbsys";
 		reg = <0 0x1a000000 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -773,9 +770,8 @@
 		};
 	};
 
-	pciesys: pciesys@1a100800 {
-		compatible = "mediatek,mt7622-pciesys",
-			     "syscon";
+	pciesys: clock-controller@1a100800 {
+		compatible = "mediatek,mt7622-pciesys";
 		reg = <0 0x1a100800 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -893,7 +889,13 @@
 		};
 	};
 
-	ethsys: syscon@1b000000 {
+	hifsys: clock-controller@1af00000 {
+		compatible = "mediatek,mt7622-hifsys";
+		reg = <0 0x1af00000 0 0x70>;
+		#clock-cells = <1>;
+	};
+
+	ethsys: clock-controller@1b000000 {
 		compatible = "mediatek,mt7622-ethsys",
 			     "syscon";
 		reg = <0 0x1b000000 0 0x1000>;
@@ -911,10 +913,28 @@
 		#dma-cells = <1>;
 	};
 
-	eth: ethernet@1b100000 {
-		compatible = "mediatek,mt7622-eth",
-			     "mediatek,mt2701-eth",
+	pcie_mirror: pcie-mirror@10000400 {
+		compatible = "mediatek,mt7622-pcie-mirror",
 			     "syscon";
+		reg = <0 0x10000400 0 0x10>;
+	};
+
+	wed0: wed@1020a000 {
+		compatible = "mediatek,mt7622-wed",
+			     "syscon";
+		reg = <0 0x1020a000 0 0x1000>;
+		interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	wed1: wed@1020b000 {
+		compatible = "mediatek,mt7622-wed",
+			     "syscon";
+		reg = <0 0x1020b000 0 0x1000>;
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	eth: ethernet@1b100000 {
+		compatible = "mediatek,mt7622-eth";
 		reg = <0 0x1b100000 0 0x20000>;
 		interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_LOW>,
 			     <GIC_SPI 224 IRQ_TYPE_LEVEL_LOW>,
@@ -937,6 +957,11 @@
 		power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
 		mediatek,ethsys = <&ethsys>;
 		mediatek,sgmiisys = <&sgmiisys>;
+		mediatek,cci-control = <&cci_control2>;
+		mediatek,wed = <&wed0>, <&wed1>;
+		mediatek,pcie-mirror = <&pcie_mirror>;
+		mediatek,hifsys = <&hifsys>;
+		dma-coherent;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		status = "disabled";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
@@ -43,6 +43,14 @@
 		interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x2c>;
 		hid-descr-addr = <0x0020>;
+		/*
+		 * The trackpad needs a post-power-on delay of 100ms,
+		 * but at time of writing, the power supply for it on
+		 * this board is always on. The delay is therefore not
+		 * added to avoid impacting the readiness of the
+		 * trackpad.
+		 */
+		vdd-supply = <&mt6397_vgp6_reg>;
 		wakeup-source;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
@@ -914,7 +914,7 @@
 		interrupt-controller;
 		#interrupt-cells = <2>;
 
-		clock: mt6397clock {
+		clock: clocks {
 			compatible = "mediatek,mt6397-clk";
 			#clock-cells = <1>;
 		};
@@ -926,11 +926,10 @@
 			#gpio-cells = <2>;
 		};
 
-		regulator: mt6397regulator {
+		regulators {
 			compatible = "mediatek,mt6397-regulator";
 
 			mt6397_vpca15_reg: buck_vpca15 {
-				regulator-compatible = "buck_vpca15";
 				regulator-name = "vpca15";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -940,7 +939,6 @@
 			};
 
 			mt6397_vpca7_reg: buck_vpca7 {
-				regulator-compatible = "buck_vpca7";
 				regulator-name = "vpca7";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -950,7 +948,6 @@
 			};
 
 			mt6397_vsramca15_reg: buck_vsramca15 {
-				regulator-compatible = "buck_vsramca15";
 				regulator-name = "vsramca15";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -959,7 +956,6 @@
 			};
 
 			mt6397_vsramca7_reg: buck_vsramca7 {
-				regulator-compatible = "buck_vsramca7";
 				regulator-name = "vsramca7";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -968,7 +964,6 @@
 			};
 
 			mt6397_vcore_reg: buck_vcore {
-				regulator-compatible = "buck_vcore";
 				regulator-name = "vcore";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -977,7 +972,6 @@
 			};
 
 			mt6397_vgpu_reg: buck_vgpu {
-				regulator-compatible = "buck_vgpu";
 				regulator-name = "vgpu";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -986,7 +980,6 @@
 			};
 
 			mt6397_vdrm_reg: buck_vdrm {
-				regulator-compatible = "buck_vdrm";
 				regulator-name = "vdrm";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1400000>;
@@ -995,7 +988,6 @@
 			};
 
 			mt6397_vio18_reg: buck_vio18 {
-				regulator-compatible = "buck_vio18";
 				regulator-name = "vio18";
 				regulator-min-microvolt = <1620000>;
 				regulator-max-microvolt = <1980000>;
@@ -1004,18 +996,15 @@
 			};
 
 			mt6397_vtcxo_reg: ldo_vtcxo {
-				regulator-compatible = "ldo_vtcxo";
 				regulator-name = "vtcxo";
 				regulator-always-on;
 			};
 
 			mt6397_va28_reg: ldo_va28 {
-				regulator-compatible = "ldo_va28";
 				regulator-name = "va28";
 			};
 
 			mt6397_vcama_reg: ldo_vcama {
-				regulator-compatible = "ldo_vcama";
 				regulator-name = "vcama";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -1023,18 +1012,15 @@
 			};
 
 			mt6397_vio28_reg: ldo_vio28 {
-				regulator-compatible = "ldo_vio28";
 				regulator-name = "vio28";
 				regulator-always-on;
 			};
 
 			mt6397_vusb_reg: ldo_vusb {
-				regulator-compatible = "ldo_vusb";
 				regulator-name = "vusb";
 			};
 
 			mt6397_vmc_reg: ldo_vmc {
-				regulator-compatible = "ldo_vmc";
 				regulator-name = "vmc";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
@@ -1042,7 +1028,6 @@
 			};
 
 			mt6397_vmch_reg: ldo_vmch {
-				regulator-compatible = "ldo_vmch";
 				regulator-name = "vmch";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -1050,7 +1035,6 @@
 			};
 
 			mt6397_vemc_3v3_reg: ldo_vemc3v3 {
-				regulator-compatible = "ldo_vemc3v3";
 				regulator-name = "vemc_3v3";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -1058,7 +1042,6 @@
 			};
 
 			mt6397_vgp1_reg: ldo_vgp1 {
-				regulator-compatible = "ldo_vgp1";
 				regulator-name = "vcamd";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -1066,7 +1049,6 @@
 			};
 
 			mt6397_vgp2_reg: ldo_vgp2 {
-				regulator-compatible = "ldo_vgp2";
 				regulator-name = "vcamio";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -1074,7 +1056,6 @@
 			};
 
 			mt6397_vgp3_reg: ldo_vgp3 {
-				regulator-compatible = "ldo_vgp3";
 				regulator-name = "vcamaf";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -1082,7 +1063,6 @@
 			};
 
 			mt6397_vgp4_reg: ldo_vgp4 {
-				regulator-compatible = "ldo_vgp4";
 				regulator-name = "vgp4";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
@@ -1090,7 +1070,6 @@
 			};
 
 			mt6397_vgp5_reg: ldo_vgp5 {
-				regulator-compatible = "ldo_vgp5";
 				regulator-name = "vgp5";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3000000>;
@@ -1098,7 +1077,6 @@
 			};
 
 			mt6397_vgp6_reg: ldo_vgp6 {
-				regulator-compatible = "ldo_vgp6";
 				regulator-name = "vgp6";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -1107,7 +1085,6 @@
 			};
 
 			mt6397_vibr_reg: ldo_vibr {
-				regulator-compatible = "ldo_vibr";
 				regulator-name = "vibr";
 				regulator-min-microvolt = <1300000>;
 				regulator-max-microvolt = <3300000>;
@@ -1115,7 +1092,7 @@
 			};
 		};
 
-		rtc: mt6397rtc {
+		rtc: rtc {
 			compatible = "mediatek,mt6397-rtc";
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
@@ -43,7 +43,7 @@
 		id-gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
 	};
 
-	usb_p1_vbus: regulator@0 {
+	usb_p1_vbus: regulator-usb-p1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -52,7 +52,7 @@
 		enable-active-high;
 	};
 
-	usb_p0_vbus: regulator@1 {
+	usb_p0_vbus: regulator-usb-p0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vbus";
 		regulator-min-microvolt = <5000000>;
@@ -307,11 +307,10 @@
 		interrupt-controller;
 		#interrupt-cells = <2>;
 
-		mt6397regulator: mt6397regulator {
+		regulators {
 			compatible = "mediatek,mt6397-regulator";
 
 			mt6397_vpca15_reg: buck_vpca15 {
-				regulator-compatible = "buck_vpca15";
 				regulator-name = "vpca15";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -320,7 +319,6 @@
 			};
 
 			mt6397_vpca7_reg: buck_vpca7 {
-				regulator-compatible = "buck_vpca7";
 				regulator-name = "vpca7";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -329,7 +327,6 @@
 			};
 
 			mt6397_vsramca15_reg: buck_vsramca15 {
-				regulator-compatible = "buck_vsramca15";
 				regulator-name = "vsramca15";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -338,7 +335,6 @@
 			};
 
 			mt6397_vsramca7_reg: buck_vsramca7 {
-				regulator-compatible = "buck_vsramca7";
 				regulator-name = "vsramca7";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -347,7 +343,6 @@
 			};
 
 			mt6397_vcore_reg: buck_vcore {
-				regulator-compatible = "buck_vcore";
 				regulator-name = "vcore";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -356,7 +351,6 @@
 			};
 
 			mt6397_vgpu_reg: buck_vgpu {
-				regulator-compatible = "buck_vgpu";
 				regulator-name = "vgpu";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -365,7 +359,6 @@
 			};
 
 			mt6397_vdrm_reg: buck_vdrm {
-				regulator-compatible = "buck_vdrm";
 				regulator-name = "vdrm";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1400000>;
@@ -374,7 +367,6 @@
 			};
 
 			mt6397_vio18_reg: buck_vio18 {
-				regulator-compatible = "buck_vio18";
 				regulator-name = "vio18";
 				regulator-min-microvolt = <1620000>;
 				regulator-max-microvolt = <1980000>;
@@ -383,19 +375,16 @@
 			};
 
 			mt6397_vtcxo_reg: ldo_vtcxo {
-				regulator-compatible = "ldo_vtcxo";
 				regulator-name = "vtcxo";
 				regulator-always-on;
 			};
 
 			mt6397_va28_reg: ldo_va28 {
-				regulator-compatible = "ldo_va28";
 				regulator-name = "va28";
 				regulator-always-on;
 			};
 
 			mt6397_vcama_reg: ldo_vcama {
-				regulator-compatible = "ldo_vcama";
 				regulator-name = "vcama";
 				regulator-min-microvolt = <1500000>;
 				regulator-max-microvolt = <2800000>;
@@ -403,18 +392,15 @@
 			};
 
 			mt6397_vio28_reg: ldo_vio28 {
-				regulator-compatible = "ldo_vio28";
 				regulator-name = "vio28";
 				regulator-always-on;
 			};
 
 			mt6397_vusb_reg: ldo_vusb {
-				regulator-compatible = "ldo_vusb";
 				regulator-name = "vusb";
 			};
 
 			mt6397_vmc_reg: ldo_vmc {
-				regulator-compatible = "ldo_vmc";
 				regulator-name = "vmc";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
@@ -422,7 +408,6 @@
 			};
 
 			mt6397_vmch_reg: ldo_vmch {
-				regulator-compatible = "ldo_vmch";
 				regulator-name = "vmch";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -430,7 +415,6 @@
 			};
 
 			mt6397_vemc_3v3_reg: ldo_vemc3v3 {
-				regulator-compatible = "ldo_vemc3v3";
 				regulator-name = "vemc_3v3";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -438,7 +422,6 @@
 			};
 
 			mt6397_vgp1_reg: ldo_vgp1 {
-				regulator-compatible = "ldo_vgp1";
 				regulator-name = "vcamd";
 				regulator-min-microvolt = <1220000>;
 				regulator-max-microvolt = <3300000>;
@@ -446,7 +429,6 @@
 			};
 
 			mt6397_vgp2_reg: ldo_vgp2 {
-				regulator-compatible = "ldo_vgp2";
 				regulator-name = "vcamio";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <3300000>;
@@ -454,7 +436,6 @@
 			};
 
 			mt6397_vgp3_reg: ldo_vgp3 {
-				regulator-compatible = "ldo_vgp3";
 				regulator-name = "vcamaf";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
@@ -462,7 +443,6 @@
 			};
 
 			mt6397_vgp4_reg: ldo_vgp4 {
-				regulator-compatible = "ldo_vgp4";
 				regulator-name = "vgp4";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
@@ -470,7 +450,6 @@
 			};
 
 			mt6397_vgp5_reg: ldo_vgp5 {
-				regulator-compatible = "ldo_vgp5";
 				regulator-name = "vgp5";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3000000>;
@@ -478,7 +457,6 @@
 			};
 
 			mt6397_vgp6_reg: ldo_vgp6 {
-				regulator-compatible = "ldo_vgp6";
 				regulator-name = "vgp6";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
@@ -486,7 +464,6 @@
 			};
 
 			mt6397_vibr_reg: ldo_vibr {
-				regulator-compatible = "ldo_vibr";
 				regulator-name = "vibr";
 				regulator-min-microvolt = <1300000>;
 				regulator-max-microvolt = <3300000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -273,7 +273,7 @@
 	};
 
 	thermal-zones {
-		cpu_thermal: cpu_thermal {
+		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <1000>; /* milliseconds */
 			polling-delay = <1000>; /* milliseconds */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
@@ -30,7 +30,7 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
-		scp_mem_reserved: scp_mem_region {
+		scp_mem_reserved: memory@50000000 {
 			compatible = "shared-dma-pool";
 			reg = <0 0x50000000 0 0x2900000>;
 			no-map;
@@ -131,8 +131,8 @@
 };
 
 &pio {
-	i2c_pins_0: i2c0{
-		pins_i2c{
+	i2c_pins_0: i2c0 {
+		pins_i2c {
 			pinmux = <PINMUX_GPIO82__FUNC_SDA0>,
 				 <PINMUX_GPIO83__FUNC_SCL0>;
 			mediatek,pull-up-adv = <3>;
@@ -140,8 +140,8 @@
 		};
 	};
 
-	i2c_pins_1: i2c1{
-		pins_i2c{
+	i2c_pins_1: i2c1 {
+		pins_i2c {
 			pinmux = <PINMUX_GPIO81__FUNC_SDA1>,
 				 <PINMUX_GPIO84__FUNC_SCL1>;
 			mediatek,pull-up-adv = <3>;
@@ -149,8 +149,8 @@
 		};
 	};
 
-	i2c_pins_2: i2c2{
-		pins_i2c{
+	i2c_pins_2: i2c2 {
+		pins_i2c {
 			pinmux = <PINMUX_GPIO103__FUNC_SCL2>,
 				 <PINMUX_GPIO104__FUNC_SDA2>;
 			mediatek,pull-up-adv = <3>;
@@ -158,8 +158,8 @@
 		};
 	};
 
-	i2c_pins_3: i2c3{
-		pins_i2c{
+	i2c_pins_3: i2c3 {
+		pins_i2c {
 			pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
 				 <PINMUX_GPIO51__FUNC_SDA3>;
 			mediatek,pull-up-adv = <3>;
@@ -167,8 +167,8 @@
 		};
 	};
 
-	i2c_pins_4: i2c4{
-		pins_i2c{
+	i2c_pins_4: i2c4 {
+		pins_i2c {
 			pinmux = <PINMUX_GPIO105__FUNC_SCL4>,
 				 <PINMUX_GPIO106__FUNC_SDA4>;
 			mediatek,pull-up-adv = <3>;
@@ -176,8 +176,8 @@
 		};
 	};
 
-	i2c_pins_5: i2c5{
-		pins_i2c{
+	i2c_pins_5: i2c5 {
+		pins_i2c {
 			pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
 				 <PINMUX_GPIO49__FUNC_SDA5>;
 			mediatek,pull-up-adv = <3>;
@@ -185,8 +185,8 @@
 		};
 	};
 
-	spi_pins_0: spi0{
-		pins_spi{
+	spi_pins_0: spi0 {
+		pins_spi {
 			pinmux = <PINMUX_GPIO85__FUNC_SPI0_MI>,
 				 <PINMUX_GPIO86__FUNC_SPI0_CSB>,
 				 <PINMUX_GPIO87__FUNC_SPI0_MO>,
@@ -300,8 +300,8 @@
 		};
 	};
 
-	spi_pins_1: spi1{
-		pins_spi{
+	spi_pins_1: spi1 {
+		pins_spi {
 			pinmux = <PINMUX_GPIO161__FUNC_SPI1_A_MI>,
 				 <PINMUX_GPIO162__FUNC_SPI1_A_CSB>,
 				 <PINMUX_GPIO163__FUNC_SPI1_A_MO>,
@@ -310,8 +310,8 @@
 		};
 	};
 
-	spi_pins_2: spi2{
-		pins_spi{
+	spi_pins_2: spi2 {
+		pins_spi {
 			pinmux = <PINMUX_GPIO0__FUNC_SPI2_CSB>,
 				 <PINMUX_GPIO1__FUNC_SPI2_MO>,
 				 <PINMUX_GPIO2__FUNC_SPI2_CLK>,
@@ -320,8 +320,8 @@
 		};
 	};
 
-	spi_pins_3: spi3{
-		pins_spi{
+	spi_pins_3: spi3 {
+		pins_spi {
 			pinmux = <PINMUX_GPIO21__FUNC_SPI3_MI>,
 				 <PINMUX_GPIO22__FUNC_SPI3_CSB>,
 				 <PINMUX_GPIO23__FUNC_SPI3_MO>,
@@ -330,8 +330,8 @@
 		};
 	};
 
-	spi_pins_4: spi4{
-		pins_spi{
+	spi_pins_4: spi4 {
+		pins_spi {
 			pinmux = <PINMUX_GPIO17__FUNC_SPI4_MI>,
 				 <PINMUX_GPIO18__FUNC_SPI4_CSB>,
 				 <PINMUX_GPIO19__FUNC_SPI4_MO>,
@@ -340,8 +340,8 @@
 		};
 	};
 
-	spi_pins_5: spi5{
-		pins_spi{
+	spi_pins_5: spi5 {
+		pins_spi {
 			pinmux = <PINMUX_GPIO13__FUNC_SPI5_MI>,
 				 <PINMUX_GPIO14__FUNC_SPI5_CSB>,
 				 <PINMUX_GPIO15__FUNC_SPI5_MO>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dts
@@ -28,3 +28,6 @@
 	};
 };
 
+&i2c2 {
+	i2c-scl-internal-delay-ns = <4100>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts
@@ -25,7 +25,14 @@
 	hid-descr-addr = <0x0001>;
 };
 
+&mt6358codec {
+	mediatek,dmic-mode = <1>; /* one-wire */
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "GO_DAMU";
 };
 
+&i2c2 {
+	i2c-scl-internal-delay-ns = <20000>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
@@ -25,3 +25,6 @@
 	};
 };
 
+&i2c2 {
+	i2c-scl-internal-delay-ns = <21500>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kenzo.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kenzo.dts
@@ -10,3 +10,18 @@
 	model = "Google kenzo sku17 board";
 	compatible = "google,juniper-sku17", "google,juniper", "mediatek,mt8183";
 };
+
+&i2c0 {
+	touchscreen@40 {
+		compatible = "hid-over-i2c";
+		reg = <0x40>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_pins>;
+
+		interrupts-extended = <&pio 155 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <70>;
+		hid-descr-addr = <0x0001>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow.dtsi
@@ -6,6 +6,21 @@
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi.dtsi"
 
+&i2c0 {
+	touchscreen@40 {
+		compatible = "hid-over-i2c";
+		reg = <0x40>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_pins>;
+
+		interrupts-extended = <&pio 155 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <70>;
+		hid-descr-addr = <0x0001>;
+	};
+};
+
 &i2c2 {
 	trackpad@2c {
 		compatible = "hid-over-i2c";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi
@@ -4,50 +4,41 @@
  */
 
 #include "mt8183-kukui.dtsi"
+/* Must come after mt8183-kukui.dtsi to modify cros_ec */
+#include <arm/cros-ec-keyboard.dtsi>
 
 / {
-	panel: panel {
-		compatible = "auo,b116xw03";
-		power-supply = <&pp3300_panel>;
-		ddc-i2c-bus = <&i2c4>;
-		backlight = <&backlight_lcd0>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&anx7625_out>;
-			};
-		};
-	};
-
-	pp1200_mipibrdg: pp1200-mipibrdg {
+	pp1000_mipibrdg: pp1000-mipibrdg {
 		compatible = "regulator-fixed";
-		regulator-name = "pp1200_mipibrdg";
+		regulator-name = "pp1000_mipibrdg";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&pp1200_mipibrdg_en>;
+		pinctrl-0 = <&pp1000_mipibrdg_en>;
 
 		enable-active-high;
 		regulator-boot-on;
 
 		gpio = <&pio 54 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pp1800_alw>;
 	};
 
 	pp1800_mipibrdg: pp1800-mipibrdg {
 		compatible = "regulator-fixed";
 		regulator-name = "pp1800_mipibrdg";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pp1800_lcd_en>;
+		pinctrl-0 = <&pp1800_mipibrdg_en>;
 
 		enable-active-high;
 		regulator-boot-on;
 
 		gpio = <&pio 36 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pp1800_alw>;
 	};
 
 	pp3300_panel: pp3300-panel {
 		compatible = "regulator-fixed";
 		regulator-name = "pp3300_panel";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pp3300_panel_pins>;
 
@@ -55,18 +46,20 @@
 		regulator-boot-on;
 
 		gpio = <&pio 35 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pp3300_alw>;
 	};
 
-	vddio_mipibrdg: vddio-mipibrdg {
+	pp3300_mipibrdg: pp3300-mipibrdg {
 		compatible = "regulator-fixed";
-		regulator-name = "vddio_mipibrdg";
+		regulator-name = "pp3300_mipibrdg";
 		pinctrl-names = "default";
-		pinctrl-0 = <&vddio_mipibrdg_en>;
+		pinctrl-0 = <&pp3300_mipibrdg_en>;
 
 		enable-active-high;
 		regulator-boot-on;
 
 		gpio = <&pio 37 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pp3300_alw>;
 	};
 
 	volume_buttons: volume-buttons {
@@ -102,6 +95,8 @@
 
 &dsi0 {
 	status = "okay";
+	/delete-property/#size-cells;
+	/delete-property/#address-cells;
 	/delete-node/panel@0;
 	ports {
 		port {
@@ -161,25 +156,42 @@
 		panel_flags = <1>;
 		enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
 		reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
-		vdd10-supply = <&pp1200_mipibrdg>;
+		vdd10-supply = <&pp1000_mipibrdg>;
 		vdd18-supply = <&pp1800_mipibrdg>;
-		vdd33-supply = <&vddio_mipibrdg>;
+		vdd33-supply = <&pp3300_mipibrdg>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				anx7625_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+				};
+			};
 
-		#address-cells = <1>;
-		#size-cells = <0>;
-		port@0 {
-			reg = <0>;
+			port@1 {
+				reg = <1>;
 
-			anx7625_in: endpoint {
-				remote-endpoint = <&dsi_out>;
+				anx7625_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
 			};
 		};
 
-		port@1 {
-			reg = <1>;
-
-			anx7625_out: endpoint {
-				remote-endpoint = <&panel_in>;
+		aux-bus {
+			panel: panel {
+				compatible = "edp-panel";
+				power-supply = <&pp3300_panel>;
+				backlight = <&backlight_lcd0>;
+
+				port {
+					panel_in: endpoint {
+						remote-endpoint = <&anx7625_out>;
+					};
+				};
 			};
 		};
 	};
@@ -389,14 +401,14 @@
 		"",
 		"";
 
-	pp1200_mipibrdg_en: pp1200-mipibrdg-en {
+	pp1000_mipibrdg_en: pp1000-mipibrdg-en {
 		pins1 {
 			pinmux = <PINMUX_GPIO54__FUNC_GPIO54>;
 			output-low;
 		};
 	};
 
-	pp1800_lcd_en: pp1800-lcd-en {
+	pp1800_mipibrdg_en: pp1800-mipibrdg-en {
 		pins1 {
 			pinmux = <PINMUX_GPIO36__FUNC_GPIO36>;
 			output-low;
@@ -438,27 +450,27 @@
 	};
 
 	touchscreen_pins: touchscreen-pins {
-		touch_int_odl {
+		touch-int-odl {
 			pinmux = <PINMUX_GPIO155__FUNC_GPIO155>;
 			input-enable;
 			bias-pull-up;
 		};
 
-		touch_rst_l {
+		touch-rst-l {
 			pinmux = <PINMUX_GPIO156__FUNC_GPIO156>;
 			output-high;
 		};
 	};
 
 	trackpad_pins: trackpad-pins {
-		trackpad_int {
+		trackpad-int {
 			pinmux = <PINMUX_GPIO7__FUNC_GPIO7>;
 			input-enable;
 			bias-disable; /* pulled externally */
 		};
 	};
 
-	vddio_mipibrdg_en: vddio-mipibrdg-en {
+	pp3300_mipibrdg_en: pp3300-mipibrdg-en {
 		pins1 {
 			pinmux = <PINMUX_GPIO37__FUNC_GPIO37>;
 			output-low;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi
@@ -105,9 +105,9 @@
 	clock-frequency = <400000>;
 	vbus-supply = <&mt6358_vcn18_reg>;
 
-	eeprom@54 {
+	eeprom@50 {
 		compatible = "atmel,24c32";
-		reg = <0x54>;
+		reg = <0x50>;
 		pagesize = <32>;
 		vcc-supply = <&mt6358_vcn18_reg>;
 	};
@@ -372,6 +372,16 @@
 	};
 };
 
+&cros_ec {
+	cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "GO_KAKADU";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi
@@ -79,9 +79,9 @@
 	clock-frequency = <400000>;
 	vbus-supply = <&mt6358_vcn18_reg>;
 
-	eeprom@54 {
+	eeprom@50 {
 		compatible = "atmel,24c64";
-		reg = <0x54>;
+		reg = <0x50>;
 		pagesize = <32>;
 		vcc-supply = <&mt6358_vcn18_reg>;
 	};
@@ -338,6 +338,16 @@
 	};
 };
 
+&cros_ec {
+	cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "GO_KODAMA";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
@@ -88,9 +88,9 @@
 	clock-frequency = <400000>;
 	vbus-supply = <&mt6358_vcn18_reg>;
 
-	eeprom@54 {
+	eeprom@50 {
 		compatible = "atmel,24c32";
-		reg = <0x54>;
+		reg = <0x50>;
 		pagesize = <32>;
 		vcc-supply = <&mt6358_vcn18_reg>;
 	};
@@ -342,6 +342,16 @@
 	};
 };
 
+&cros_ec {
+	cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "LE_Krane";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
@@ -108,7 +108,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		scp_mem_reserved: scp_mem_region {
+		scp_mem_reserved: memory@50000000 {
 			compatible = "shared-dma-pool";
 			reg = <0 0x50000000 0 0x2900000>;
 			no-map;
@@ -281,6 +281,10 @@
 	};
 };
 
+&gic {
+	mediatek,broken-save-restore-fw;
+};
+
 &gpu {
 	mali-supply = <&mt6358_vgpu_reg>;
 	sram-supply = <&mt6358_vsram_gpu_reg>;
@@ -403,13 +407,13 @@
 
 &pio {
 	bt_pins: bt-pins {
-		pins_bt_en {
+		pins-bt-en {
 			pinmux = <PINMUX_GPIO120__FUNC_GPIO120>;
 			output-low;
 		};
 	};
 
-	ec_ap_int_odl: ec_ap_int_odl {
+	ec_ap_int_odl: ec-ap-int-odl {
 		pins1 {
 			pinmux = <PINMUX_GPIO151__FUNC_GPIO151>;
 			input-enable;
@@ -417,7 +421,7 @@
 		};
 	};
 
-	h1_int_od_l: h1_int_od_l {
+	h1_int_od_l: h1-int-od-l {
 		pins1 {
 			pinmux = <PINMUX_GPIO153__FUNC_GPIO153>;
 			input-enable;
@@ -425,7 +429,7 @@
 	};
 
 	i2c0_pins: i2c0 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO82__FUNC_SDA0>,
 				 <PINMUX_GPIO83__FUNC_SCL0>;
 			mediatek,pull-up-adv = <3>;
@@ -434,7 +438,7 @@
 	};
 
 	i2c1_pins: i2c1 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO81__FUNC_SDA1>,
 				 <PINMUX_GPIO84__FUNC_SCL1>;
 			mediatek,pull-up-adv = <3>;
@@ -443,7 +447,7 @@
 	};
 
 	i2c2_pins: i2c2 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO103__FUNC_SCL2>,
 				 <PINMUX_GPIO104__FUNC_SDA2>;
 			bias-disable;
@@ -452,7 +456,7 @@
 	};
 
 	i2c3_pins: i2c3 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
 				 <PINMUX_GPIO51__FUNC_SDA3>;
 			mediatek,pull-up-adv = <3>;
@@ -461,7 +465,7 @@
 	};
 
 	i2c4_pins: i2c4 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO105__FUNC_SCL4>,
 				 <PINMUX_GPIO106__FUNC_SDA4>;
 			bias-disable;
@@ -470,7 +474,7 @@
 	};
 
 	i2c5_pins: i2c5 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
 				 <PINMUX_GPIO49__FUNC_SDA5>;
 			mediatek,pull-up-adv = <3>;
@@ -479,7 +483,7 @@
 	};
 
 	i2c6_pins: i2c6 {
-		pins_bus {
+		pins-bus {
 			pinmux = <PINMUX_GPIO11__FUNC_SCL6>,
 				 <PINMUX_GPIO12__FUNC_SDA6>;
 			bias-disable;
@@ -487,7 +491,7 @@
 	};
 
 	mmc0_pins_default: mmc0-pins-default {
-		pins_cmd_dat {
+		pins-cmd-dat {
 			pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
 				 <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
 				 <PINMUX_GPIO125__FUNC_MSDC0_DAT2>,
@@ -502,13 +506,13 @@
 			mediatek,pull-up-adv = <01>;
 		};
 
-		pins_clk {
+		pins-clk {
 			pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
 			drive-strength = <MTK_DRIVE_14mA>;
 			mediatek,pull-down-adv = <10>;
 		};
 
-		pins_rst {
+		pins-rst {
 			pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
 			drive-strength = <MTK_DRIVE_14mA>;
 			mediatek,pull-down-adv = <01>;
@@ -516,7 +520,7 @@
 	};
 
 	mmc0_pins_uhs: mmc0-pins-uhs {
-		pins_cmd_dat {
+		pins-cmd-dat {
 			pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
 				 <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
 				 <PINMUX_GPIO125__FUNC_MSDC0_DAT2>,
@@ -531,19 +535,19 @@
 			mediatek,pull-up-adv = <01>;
 		};
 
-		pins_clk {
+		pins-clk {
 			pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
 			drive-strength = <MTK_DRIVE_14mA>;
 			mediatek,pull-down-adv = <10>;
 		};
 
-		pins_ds {
+		pins-ds {
 			pinmux = <PINMUX_GPIO131__FUNC_MSDC0_DSL>;
 			drive-strength = <MTK_DRIVE_14mA>;
 			mediatek,pull-down-adv = <10>;
 		};
 
-		pins_rst {
+		pins-rst {
 			pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
 			drive-strength = <MTK_DRIVE_14mA>;
 			mediatek,pull-up-adv = <01>;
@@ -551,7 +555,7 @@
 	};
 
 	mmc1_pins_default: mmc1-pins-default {
-		pins_cmd_dat {
+		pins-cmd-dat {
 			pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
 				 <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
 				 <PINMUX_GPIO34__FUNC_MSDC1_DAT1>,
@@ -561,7 +565,7 @@
 			mediatek,pull-up-adv = <10>;
 		};
 
-		pins_clk {
+		pins-clk {
 			pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
 			input-enable;
 			mediatek,pull-down-adv = <10>;
@@ -569,7 +573,7 @@
 	};
 
 	mmc1_pins_uhs: mmc1-pins-uhs {
-		pins_cmd_dat {
+		pins-cmd-dat {
 			pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
 				 <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
 				 <PINMUX_GPIO34__FUNC_MSDC1_DAT1>,
@@ -580,7 +584,7 @@
 			mediatek,pull-up-adv = <10>;
 		};
 
-		pins_clk {
+		pins-clk {
 			pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
 			drive-strength = <MTK_DRIVE_8mA>;
 			mediatek,pull-down-adv = <10>;
@@ -588,15 +592,15 @@
 		};
 	};
 
-	panel_pins_default: panel_pins_default {
-		panel_reset {
+	panel_pins_default: panel-pins-default {
+		panel-reset {
 			pinmux = <PINMUX_GPIO45__FUNC_GPIO45>;
 			output-low;
 			bias-pull-up;
 		};
 	};
 
-	pwm0_pin_default: pwm0_pin_default {
+	pwm0_pin_default: pwm0-pin-default {
 		pins1 {
 			pinmux = <PINMUX_GPIO176__FUNC_GPIO176>;
 			output-high;
@@ -608,14 +612,14 @@
 	};
 
 	scp_pins: scp {
-		pins_scp_uart {
+		pins-scp-uart {
 			pinmux = <PINMUX_GPIO110__FUNC_TP_URXD1_AO>,
 				 <PINMUX_GPIO112__FUNC_TP_UTXD1_AO>;
 		};
 	};
 
 	spi0_pins: spi0 {
-		pins_spi{
+		pins-spi {
 			pinmux = <PINMUX_GPIO85__FUNC_SPI0_MI>,
 				 <PINMUX_GPIO86__FUNC_GPIO86>,
 				 <PINMUX_GPIO87__FUNC_SPI0_MO>,
@@ -625,7 +629,7 @@
 	};
 
 	spi1_pins: spi1 {
-		pins_spi{
+		pins-spi {
 			pinmux = <PINMUX_GPIO161__FUNC_SPI1_A_MI>,
 				 <PINMUX_GPIO162__FUNC_SPI1_A_CSB>,
 				 <PINMUX_GPIO163__FUNC_SPI1_A_MO>,
@@ -635,20 +639,20 @@
 	};
 
 	spi2_pins: spi2 {
-		pins_spi{
+		pins-spi {
 			pinmux = <PINMUX_GPIO0__FUNC_SPI2_CSB>,
 				 <PINMUX_GPIO1__FUNC_SPI2_MO>,
 				 <PINMUX_GPIO2__FUNC_SPI2_CLK>;
 			bias-disable;
 		};
-		pins_spi_mi {
+		pins-spi-mi {
 			pinmux = <PINMUX_GPIO94__FUNC_SPI2_MI>;
 			mediatek,pull-down-adv = <00>;
 		};
 	};
 
 	spi3_pins: spi3 {
-		pins_spi{
+		pins-spi {
 			pinmux = <PINMUX_GPIO21__FUNC_SPI3_MI>,
 				 <PINMUX_GPIO22__FUNC_SPI3_CSB>,
 				 <PINMUX_GPIO23__FUNC_SPI3_MO>,
@@ -658,7 +662,7 @@
 	};
 
 	spi4_pins: spi4 {
-		pins_spi{
+		pins-spi {
 			pinmux = <PINMUX_GPIO17__FUNC_SPI4_MI>,
 				 <PINMUX_GPIO18__FUNC_SPI4_CSB>,
 				 <PINMUX_GPIO19__FUNC_SPI4_MO>,
@@ -668,7 +672,7 @@
 	};
 
 	spi5_pins: spi5 {
-		pins_spi{
+		pins-spi {
 			pinmux = <PINMUX_GPIO13__FUNC_SPI5_MI>,
 				 <PINMUX_GPIO14__FUNC_SPI5_CSB>,
 				 <PINMUX_GPIO15__FUNC_SPI5_MO>,
@@ -678,63 +682,61 @@
 	};
 
 	uart0_pins_default: uart0-pins-default {
-		pins_rx {
+		pins-rx {
 			pinmux = <PINMUX_GPIO95__FUNC_URXD0>;
 			input-enable;
 			bias-pull-up;
 		};
-		pins_tx {
+		pins-tx {
 			pinmux = <PINMUX_GPIO96__FUNC_UTXD0>;
 		};
 	};
 
 	uart1_pins_default: uart1-pins-default {
-		pins_rx {
+		pins-rx {
 			pinmux = <PINMUX_GPIO121__FUNC_URXD1>;
 			input-enable;
 			bias-pull-up;
 		};
-		pins_tx {
+		pins-tx {
 			pinmux = <PINMUX_GPIO115__FUNC_UTXD1>;
 		};
-		pins_rts {
+		pins-rts {
 			pinmux = <PINMUX_GPIO47__FUNC_URTS1>;
-			output-enable;
 		};
-		pins_cts {
+		pins-cts {
 			pinmux = <PINMUX_GPIO46__FUNC_UCTS1>;
 			input-enable;
 		};
 	};
 
 	uart1_pins_sleep: uart1-pins-sleep {
-		pins_rx {
+		pins-rx {
 			pinmux = <PINMUX_GPIO121__FUNC_GPIO121>;
 			input-enable;
 			bias-pull-up;
 		};
-		pins_tx {
+		pins-tx {
 			pinmux = <PINMUX_GPIO115__FUNC_UTXD1>;
 		};
-		pins_rts {
+		pins-rts {
 			pinmux = <PINMUX_GPIO47__FUNC_URTS1>;
-			output-enable;
 		};
-		pins_cts {
+		pins-cts {
 			pinmux = <PINMUX_GPIO46__FUNC_UCTS1>;
 			input-enable;
 		};
 	};
 
 	wifi_pins_pwrseq: wifi-pins-pwrseq {
-		pins_wifi_enable {
+		pins-wifi-enable {
 			pinmux = <PINMUX_GPIO119__FUNC_GPIO119>;
 			output-low;
 		};
 	};
 
 	wifi_pins_wakeup: wifi-pins-wakeup {
-		pins_wifi_wakeup {
+		pins-wifi-wakeup {
 			pinmux = <PINMUX_GPIO113__FUNC_GPIO113>;
 			input-enable;
 		};
@@ -824,8 +826,18 @@
 			google,usb-port-id = <0>;
 		};
 
-		cbas {
-			compatible = "google,cros-cbas";
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "sink";
+			};
 		};
 	};
 };
@@ -913,5 +925,4 @@
 	};
 };
 
-#include <arm/cros-ec-keyboard.dtsi>
 #include <arm/cros-ec-sbs.dtsi>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
@@ -165,7 +165,7 @@
 
 &pio {
 	i2c_pins_0: i2c0 {
-		pins_i2c{
+		pins_i2c {
 			pinmux = <PINMUX_GPIO82__FUNC_SDA0>,
 				 <PINMUX_GPIO83__FUNC_SCL0>;
 			mediatek,pull-up-adv = <3>;
@@ -174,7 +174,7 @@
 	};
 
 	i2c_pins_1: i2c1 {
-		pins_i2c{
+		pins_i2c {
 			pinmux = <PINMUX_GPIO81__FUNC_SDA1>,
 				 <PINMUX_GPIO84__FUNC_SCL1>;
 			mediatek,pull-up-adv = <3>;
@@ -183,7 +183,7 @@
 	};
 
 	i2c_pins_2: i2c2 {
-		pins_i2c{
+		pins_i2c {
 			pinmux = <PINMUX_GPIO103__FUNC_SCL2>,
 				 <PINMUX_GPIO104__FUNC_SDA2>;
 			mediatek,pull-up-adv = <3>;
@@ -192,7 +192,7 @@
 	};
 
 	i2c_pins_3: i2c3 {
-		pins_i2c{
+		pins_i2c {
 			pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
 				 <PINMUX_GPIO51__FUNC_SDA3>;
 			mediatek,pull-up-adv = <3>;
@@ -201,7 +201,7 @@
 	};
 
 	i2c_pins_4: i2c4 {
-		pins_i2c{
+		pins_i2c {
 			pinmux = <PINMUX_GPIO105__FUNC_SCL4>,
 				 <PINMUX_GPIO106__FUNC_SDA4>;
 			mediatek,pull-up-adv = <3>;
@@ -210,7 +210,7 @@
 	};
 
 	i2c_pins_5: i2c5 {
-		pins_i2c{
+		pins_i2c {
 			pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
 				 <PINMUX_GPIO49__FUNC_SDA5>;
 			mediatek,pull-up-adv = <3>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -299,6 +299,15 @@
 		method          = "smc";
 	};
 
+	clk13m: fixed-factor-clock-13m {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&clk26m>;
+		clock-div = <2>;
+		clock-mult = <1>;
+		clock-output-names = "clk13m";
+	};
+
 	clk26m: oscillator {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -610,8 +619,7 @@
 				     "mediatek,mt6765-timer";
 			reg = <0 0x10017000 0 0x1000>;
 			interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&topckgen CLK_TOP_CLK13M>;
-			clock-names = "clk13m";
+			clocks = <&clk13m>;
 		};
 
 		iommu: iommu@10205000 {
@@ -758,127 +766,6 @@
 			nvmem-cell-names = "calibration-data";
 		};
 
-		thermal_zones: thermal-zones {
-			cpu_thermal: cpu_thermal {
-				polling-delay-passive = <100>;
-				polling-delay = <500>;
-				thermal-sensors = <&thermal 0>;
-				sustainable-power = <5000>;
-
-				trips {
-					threshold: trip-point0 {
-						temperature = <68000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-
-					target: trip-point1 {
-						temperature = <80000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-
-					cpu_crit: cpu-crit {
-						temperature = <115000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&target>;
-						cooling-device = <&cpu0
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-								 <&cpu1
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-								 <&cpu2
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-								 <&cpu3
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-						contribution = <3072>;
-					};
-					map1 {
-						trip = <&target>;
-						cooling-device = <&cpu4
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-								 <&cpu5
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-								 <&cpu6
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-								 <&cpu7
-							THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-						contribution = <1024>;
-					};
-				};
-			};
-
-			/* The tzts1 ~ tzts6 don't need to polling */
-			/* The tzts1 ~ tzts6 don't need to thermal throttle */
-
-			tzts1: tzts1 {
-				polling-delay-passive = <0>;
-				polling-delay = <0>;
-				thermal-sensors = <&thermal 1>;
-				sustainable-power = <5000>;
-				trips {};
-				cooling-maps {};
-			};
-
-			tzts2: tzts2 {
-				polling-delay-passive = <0>;
-				polling-delay = <0>;
-				thermal-sensors = <&thermal 2>;
-				sustainable-power = <5000>;
-				trips {};
-				cooling-maps {};
-			};
-
-			tzts3: tzts3 {
-				polling-delay-passive = <0>;
-				polling-delay = <0>;
-				thermal-sensors = <&thermal 3>;
-				sustainable-power = <5000>;
-				trips {};
-				cooling-maps {};
-			};
-
-			tzts4: tzts4 {
-				polling-delay-passive = <0>;
-				polling-delay = <0>;
-				thermal-sensors = <&thermal 4>;
-				sustainable-power = <5000>;
-				trips {};
-				cooling-maps {};
-			};
-
-			tzts5: tzts5 {
-				polling-delay-passive = <0>;
-				polling-delay = <0>;
-				thermal-sensors = <&thermal 5>;
-				sustainable-power = <5000>;
-				trips {};
-				cooling-maps {};
-			};
-
-			tztsABB: tztsABB {
-				polling-delay-passive = <0>;
-				polling-delay = <0>;
-				thermal-sensors = <&thermal 6>;
-				sustainable-power = <5000>;
-				trips {};
-				cooling-maps {};
-			};
-		};
-
 		pwm0: pwm@1100e000 {
 			compatible = "mediatek,mt8183-disp-pwm";
 			reg = <0 0x1100e000 0 0x1000>;
@@ -1201,6 +1088,7 @@
 			compatible = "mediatek,mt8183-mfgcfg", "syscon";
 			reg = <0 0x13000000 0 0x1000>;
 			#clock-cells = <1>;
+			power-domains = <&spm MT8183_POWER_DOMAIN_MFG_ASYNC>;
 		};
 
 		gpu: gpu@13040000 {
@@ -1212,7 +1100,7 @@
 				<GIC_SPI 278 IRQ_TYPE_LEVEL_LOW>;
 			interrupt-names = "job", "mmu", "gpu";
 
-			clocks = <&topckgen CLK_TOP_MFGPLL_CK>;
+			clocks = <&mfgcfg CLK_MFG_BG3D>;
 
 			power-domains =
 				<&spm MT8183_POWER_DOMAIN_MFG_CORE0>,
@@ -1348,6 +1236,7 @@
 			clock-names = "engine", "digital", "hs";
 			phys = <&mipi_tx0>;
 			phy-names = "dphy";
+			status = "disabled";
 		};
 
 		mutex: mutex@14016000 {
@@ -1487,4 +1376,125 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_CAM>;
 		};
 	};
+
+	thermal_zones: thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <500>;
+			thermal-sensors = <&thermal 0>;
+			sustainable-power = <5000>;
+
+			trips {
+				threshold: trip-point0 {
+					temperature = <68000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				target: trip-point1 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit: cpu-crit {
+					temperature = <115000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&target>;
+					cooling-device = <&cpu0
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+							 <&cpu1
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+							 <&cpu2
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+							 <&cpu3
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+					contribution = <3072>;
+				};
+				map1 {
+					trip = <&target>;
+					cooling-device = <&cpu4
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+							 <&cpu5
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+							 <&cpu6
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+							 <&cpu7
+						THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+					contribution = <1024>;
+				};
+			};
+		};
+
+		/* The tzts1 ~ tzts6 don't need to polling */
+		/* The tzts1 ~ tzts6 don't need to thermal throttle */
+
+		tzts1: tzts1 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&thermal 1>;
+			sustainable-power = <5000>;
+			trips {};
+			cooling-maps {};
+		};
+
+		tzts2: tzts2 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&thermal 2>;
+			sustainable-power = <5000>;
+			trips {};
+			cooling-maps {};
+		};
+
+		tzts3: tzts3 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&thermal 3>;
+			sustainable-power = <5000>;
+			trips {};
+			cooling-maps {};
+		};
+
+		tzts4: tzts4 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&thermal 4>;
+			sustainable-power = <5000>;
+			trips {};
+			cooling-maps {};
+		};
+
+		tzts5: tzts5 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&thermal 5>;
+			sustainable-power = <5000>;
+			trips {};
+			cooling-maps {};
+		};
+
+		tztsABB: tztsABB {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&thermal 6>;
+			sustainable-power = <5000>;
+			trips {};
+			cooling-maps {};
+		};
+	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8192.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8192.dtsi
@@ -39,9 +39,10 @@
 			reg = <0x000>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};
 
 		cpu1: cpu@100 {
@@ -50,9 +51,10 @@
 			reg = <0x100>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};
 
 		cpu2: cpu@200 {
@@ -61,9 +63,10 @@
 			reg = <0x200>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};
 
 		cpu3: cpu@300 {
@@ -72,9 +75,10 @@
 			reg = <0x300>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};
 
 		cpu4: cpu@400 {
@@ -83,8 +87,9 @@
 			reg = <0x400>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};
 
@@ -94,8 +99,9 @@
 			reg = <0x500>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};
 
@@ -105,8 +111,9 @@
 			reg = <0x600>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};
 
@@ -116,8 +123,9 @@
 			reg = <0x700>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};
 
@@ -135,19 +143,16 @@
 				core3 {
 					cpu = <&cpu3>;
 				};
-			};
-
-			cluster1 {
-				core0 {
+				core4 {
 					cpu = <&cpu4>;
 				};
-				core1 {
+				core5 {
 					cpu = <&cpu5>;
 				};
-				core2 {
+				core6 {
 					cpu = <&cpu6>;
 				};
-				core3 {
+				core7 {
 					cpu = <&cpu7>;
 				};
 			};
@@ -168,8 +173,8 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
-			cpuoff_l: cpuoff_l {
+			entry-method = "psci";
+			cpu_sleep_l: cpu-sleep-l {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x00010001>;
 				local-timer-stop;
@@ -177,7 +182,7 @@
 				exit-latency-us = <140>;
 				min-residency-us = <780>;
 			};
-			cpuoff_b: cpuoff_b {
+			cpu_sleep_b: cpu-sleep-b {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x00010001>;
 				local-timer-stop;
@@ -185,7 +190,7 @@
 				exit-latency-us = <145>;
 				min-residency-us = <720>;
 			};
-			clusteroff_l: clusteroff_l {
+			cluster_sleep_l: cluster-sleep-l {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x01010002>;
 				local-timer-stop;
@@ -193,7 +198,7 @@
 				exit-latency-us = <155>;
 				min-residency-us = <860>;
 			};
-			clusteroff_b: clusteroff_b {
+			cluster_sleep_b: cluster-sleep-b {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x01010002>;
 				local-timer-stop;
@@ -237,6 +242,12 @@
 		compatible = "simple-bus";
 		ranges;
 
+		performance: performance-controller@11bc10 {
+			compatible = "mediatek,cpufreq-hw";
+			reg = <0 0x0011bc10 0 0x120>, <0 0x0011bd30 0 0x120>;
+			#performance-domain-cells = <1>;
+		};
+
 		gic: interrupt-controller@c000000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <4>;
@@ -433,7 +444,7 @@
 			clock-names = "spi", "sf", "axi";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		i2c3: i2c3@11cb0000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/mt8516.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/mt8516.dtsi
@@ -144,10 +144,10 @@
 		#size-cells = <2>;
 		ranges;
 
-		/* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+		/* 192 KiB reserved for ARM Trusted Firmware (BL31) */
 		bl31_secmon_reserved: secmon@43000000 {
 			no-map;
-			reg = <0 0x43000000 0 0x20000>;
+			reg = <0 0x43000000 0 0x30000>;
 		};
 	};
 
@@ -206,7 +206,7 @@
 			compatible = "mediatek,mt8516-wdt",
 				     "mediatek,mt6589-wdt";
 			reg = <0 0x10007000 0 0x1000>;
-			interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_FALLING>;
+			interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>;
 			#reset-cells = <1>;
 		};
 
@@ -269,7 +269,7 @@
 			interrupt-parent = <&gic>;
 			interrupt-controller;
 			reg = <0 0x10310000 0 0x1000>,
-			      <0 0x10320000 0 0x1000>,
+			      <0 0x1032f000 0 0x2000>,
 			      <0 0x10340000 0 0x2000>,
 			      <0 0x10360000 0 0x2000>;
 			interrupts = <GIC_PPI 9
@@ -345,14 +345,10 @@
 			reg = <0 0x11009000 0 0x90>,
 			      <0 0x11000180 0 0x80>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_LOW>;
-			clocks = <&topckgen CLK_TOP_AHB_INFRA_D2>,
-				 <&infracfg CLK_IFR_I2C0_SEL>,
-				 <&topckgen CLK_TOP_I2C0>,
+			clock-div = <2>;
+			clocks = <&topckgen CLK_TOP_I2C0>,
 				 <&topckgen CLK_TOP_APDMA>;
-			clock-names = "main-source",
-				      "main-sel",
-				      "main",
-				      "dma";
+			clock-names = "main", "dma";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -364,14 +360,10 @@
 			reg = <0 0x1100a000 0 0x90>,
 			      <0 0x11000200 0 0x80>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
-			clocks = <&topckgen CLK_TOP_AHB_INFRA_D2>,
-				 <&infracfg CLK_IFR_I2C1_SEL>,
-				 <&topckgen CLK_TOP_I2C1>,
+			clock-div = <2>;
+			clocks = <&topckgen CLK_TOP_I2C1>,
 				 <&topckgen CLK_TOP_APDMA>;
-			clock-names = "main-source",
-				      "main-sel",
-				      "main",
-				      "dma";
+			clock-names = "main", "dma";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -383,14 +375,10 @@
 			reg = <0 0x1100b000 0 0x90>,
 			      <0 0x11000280 0 0x80>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_LOW>;
-			clocks = <&topckgen CLK_TOP_AHB_INFRA_D2>,
-				 <&infracfg CLK_IFR_I2C2_SEL>,
-				 <&topckgen CLK_TOP_I2C2>,
+			clock-div = <2>;
+			clocks = <&topckgen CLK_TOP_I2C2>,
 				 <&topckgen CLK_TOP_APDMA>;
-			clock-names = "main-source",
-				      "main-sel",
-				      "main",
-				      "dma";
+			clock-names = "main", "dma";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
@@ -17,7 +17,7 @@
 	};
 
 	firmware {
-		optee: optee@4fd00000 {
+		optee: optee {
 			compatible = "linaro,optee-tz";
 			method = "smc";
 		};
@@ -48,7 +48,6 @@
 };
 
 &i2c0 {
-	clock-div = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins_a>;
 	status = "okay";
@@ -157,7 +156,6 @@
 };
 
 &i2c2 {
-	clock-div = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
@@ -210,7 +208,7 @@
 		};
 	};
 
-	i2c0_pins_a: i2c0@0 {
+	i2c0_pins_a: i2c0 {
 		pins1 {
 			pinmux = <MT8516_PIN_58_SDA0__FUNC_SDA0_0>,
 				 <MT8516_PIN_59_SCL0__FUNC_SCL0_0>;
@@ -218,7 +216,7 @@
 		};
 	};
 
-	i2c2_pins_a: i2c2@0 {
+	i2c2_pins_a: i2c2 {
 		pins1 {
 			pinmux = <MT8516_PIN_60_SDA2__FUNC_SDA2_0>,
 				 <MT8516_PIN_61_SCL2__FUNC_SCL2_0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -61,7 +61,7 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
-	psci {
+	psci: psci {
 		compatible = "arm,psci-0.2";
 		method = "smc";
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
@@ -6,6 +6,18 @@
 /dts-v1/;
 #include "sparx5.dtsi"
 
+&psci {
+	status = "disabled";
+};
+
+&cpu0 {
+	enable-method = "spin-table";
+};
+
+&cpu1 {
+	enable-method = "spin-table";
+};
+
 &uart0 {
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
@@ -9,8 +9,8 @@
 	compatible = "nvidia,norrin", "nvidia,tegra132", "nvidia,tegra124";
 
 	aliases {
-		rtc0 = "/i2c@7000d000/as3722@40";
-		rtc1 = "/rtc@7000e000";
+		rtc0 = &as3722;
+		rtc1 = &tegra_rtc;
 		serial0 = &uarta;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra132.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra132.dtsi
@@ -573,7 +573,7 @@
 		status = "disabled";
 	};
 
-	rtc@7000e000 {
+	tegra_rtc: rtc@7000e000 {
 		compatible = "nvidia,tegra124-rtc", "nvidia,tegra20-rtc";
 		reg = <0x0 0x7000e000 0x0 0x100>;
 		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra186.dtsi
@@ -1079,7 +1079,7 @@
 
 	ccplex@e000000 {
 		compatible = "nvidia,tegra186-ccplex-cluster";
-		reg = <0x0 0x0e000000 0x0 0x3fffff>;
+		reg = <0x0 0x0e000000 0x0 0x400000>;
 
 		nvidia,bpmp = <&bpmp>;
 	};
@@ -1583,6 +1583,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x30000000 0x50000>;
+		no-memory-wc;
 
 		cpu_bpmp_tx: sram@4e000 {
 			reg = <0x4e000 0x1000>;
@@ -1635,7 +1636,7 @@
 		iommus = <&smmu TEGRA186_SID_BPMP>;
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
 				    TEGRA_HSP_DB_MASTER_BPMP>;
-		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
+		shmem = <&cpu_bpmp_tx>, <&cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		#power-domain-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi
@@ -75,7 +75,7 @@
 
 		/* SDMMC1 (SD/MMC) */
 		mmc@3400000 {
-			cd-gpios = <&gpio TEGRA194_MAIN_GPIO(A, 0) GPIO_ACTIVE_LOW>;
+			cd-gpios = <&gpio TEGRA194_MAIN_GPIO(G, 7) GPIO_ACTIVE_LOW>;
 		};
 
 		/* SDMMC4 (eMMC) */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra194.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra194.dtsi
@@ -818,9 +818,8 @@
 				 <&bpmp TEGRA194_CLK_HDA2CODEC_2X>;
 			clock-names = "hda", "hda2hdmi", "hda2codec_2x";
 			resets = <&bpmp TEGRA194_RESET_HDA>,
-				 <&bpmp TEGRA194_RESET_HDA2HDMICODEC>,
-				 <&bpmp TEGRA194_RESET_HDA2CODEC_2X>;
-			reset-names = "hda", "hda2hdmi", "hda2codec_2x";
+				 <&bpmp TEGRA194_RESET_HDA2HDMICODEC>;
+			reset-names = "hda", "hda2hdmi";
 			power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISP>;
 			interconnects = <&mc TEGRA194_MEMORY_CLIENT_HDAR &emc>,
 					<&mc TEGRA194_MEMORY_CLIENT_HDAW &emc>;
@@ -2250,6 +2249,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x40000000 0x50000>;
+		no-memory-wc;
 
 		cpu_bpmp_tx: sram@4e000 {
 			reg = <0x4e000 0x1000>;
@@ -2268,7 +2268,7 @@
 		compatible = "nvidia,tegra186-bpmp";
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
 				    TEGRA_HSP_DB_MASTER_BPMP>;
-		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
+		shmem = <&cpu_bpmp_tx>, <&cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		#power-domain-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra210.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra210.dtsi
@@ -1355,8 +1355,9 @@
 			 <&tegra_car TEGRA210_CLK_DFLL_REF>,
 			 <&tegra_car TEGRA210_CLK_I2C5>;
 		clock-names = "soc", "ref", "i2c";
-		resets = <&tegra_car TEGRA210_RST_DFLL_DVCO>;
-		reset-names = "dvco";
+		resets = <&tegra_car TEGRA210_RST_DFLL_DVCO>,
+			 <&tegra_car 155>;
+		reset-names = "dvco", "dfll";
 		#clock-cells = <0>;
 		clock-output-names = "dfllCPU_out";
 		status = "disabled";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/nvidia/tegra234.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/nvidia/tegra234.dtsi
@@ -122,21 +122,22 @@
 		};
 	};
 
-	sysram@40000000 {
+	sram@40000000 {
 		compatible = "nvidia,tegra234-sysram", "mmio-sram";
-		reg = <0x0 0x40000000 0x0 0x50000>;
+		reg = <0x0 0x40000000 0x0 0x80000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0x0 0x0 0x40000000 0x50000>;
+		ranges = <0x0 0x0 0x40000000 0x80000>;
+		no-memory-wc;
 
-		cpu_bpmp_tx: shmem@4e000 {
-			reg = <0x4e000 0x1000>;
+		cpu_bpmp_tx: sram@70000 {
+			reg = <0x70000 0x1000>;
 			label = "cpu-bpmp-tx";
 			pool;
 		};
 
-		cpu_bpmp_rx: shmem@4f000 {
-			reg = <0x4f000 0x1000>;
+		cpu_bpmp_rx: sram@71000 {
+			reg = <0x71000 0x1000>;
 			label = "cpu-bpmp-rx";
 			pool;
 		};
@@ -146,7 +147,7 @@
 		compatible = "nvidia,tegra234-bpmp", "nvidia,tegra186-bpmp";
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
 				    TEGRA_HSP_DB_MASTER_BPMP>;
-		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
+		shmem = <&cpu_bpmp_tx>, <&cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		#power-domain-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
@@ -5,9 +5,850 @@
 
 /dts-v1/;
 
-#include "apq8016-sbc.dtsi"
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. APQ 8016 SBC";
 	compatible = "qcom,apq8016-sbc", "qcom,apq8016";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp1_uart1;
+		usid0 = &pm8916_0;
+		i2c0	= &blsp_i2c2;
+		i2c1	= &blsp_i2c6;
+		i2c3	= &blsp_i2c4;
+		spi0	= &blsp_spi5;
+		spi1	= &blsp_spi3;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	camera_vdddo_1v8: camera-vdddo-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdddo";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	camera_vdda_2v8: camera-vdda-2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdda";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	camera_vddd_1v5: camera-vddd-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vddd";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		ramoops@bff00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xbff00000 0x0 0x100000>;
+
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			ftrace-size = <0x20000>;
+		};
+	};
+
+	usb2513 {
+		compatible = "smsc,usb3503";
+		reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
+		initial-mode = <1>;
+	};
+
+	usb_id: usb-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_id_default>;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&msm_key_volp_n_default>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&msmgpio_leds>,
+			    <&pm8916_gpios_leds>,
+			    <&pm8916_mpps_leds>;
+
+		compatible = "gpio-leds";
+
+		led@1 {
+			label = "apq8016-sbc:green:user1";
+			gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "apq8016-sbc:green:user2";
+			gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "apq8016-sbc:green:user3";
+			gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "apq8016-sbc:green:user4";
+			gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			panic-indicator;
+			default-state = "off";
+		};
+
+		led@5 {
+			label = "apq8016-sbc:yellow:wlan";
+			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		led@6 {
+			label = "apq8016-sbc:blue:bt";
+			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp_i2c2 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-I2C0";
+};
+
+&blsp_i2c4 {
+	/* On High speed expansion */
+	status = "okay";
+	label = "HS-I2C2";
+
+	adv_bridge: bridge@39 {
+		status = "okay";
+
+		compatible = "adi,adv7533";
+		reg = <0x39>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+
+		adi,dsi-lanes = <4>;
+		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+		clock-names = "cec";
+
+		pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
+
+		avdd-supply = <&pm8916_l6>;
+		a2vdd-supply = <&pm8916_l6>;
+		dvdd-supply = <&pm8916_l6>;
+		pvdd-supply = <&pm8916_l6>;
+		v1p2-supply = <&pm8916_l6>;
+		v3p3-supply = <&pm8916_l17>;
+
+		pinctrl-names = "default","sleep";
+		pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+		pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+		#sound-dai-cells = <1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7533_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&blsp_i2c6 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-I2C1";
+};
+
+&blsp_spi3 {
+	/* On High speed expansion */
+	status = "okay";
+	label = "HS-SPI1";
+};
+
+&blsp_spi5 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-SPI0";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+	label = "LS-UART0";
+};
+
+&blsp1_uart2 {
+	status = "okay";
+	label = "LS-UART1";
+};
+
+&camss {
+	status = "okay";
+	ports {
+		port@0 {
+			reg = <0>;
+			csiphy0_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&ov5640_ep>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&cci {
+	status = "okay";
+};
+
+&cci_i2c0 {
+	camera_rear@3b {
+		compatible = "ovti,ov5640";
+		reg = <0x3b>;
+
+		enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&camera_rear_default>;
+
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "xclk";
+		clock-frequency = <23880000>;
+
+		DOVDD-supply = <&camera_vdddo_1v8>;
+		AVDD-supply = <&camera_vdda_2v8>;
+		DVDD-supply = <&camera_vddd_1v5>;
+
+		/* No camera mezzanine by default */
+		status = "disabled";
+
+		port {
+			ov5640_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&csiphy0_ep>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&adv7533_in>;
+};
+
+&lpass {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mpss {
+	status = "okay";
+
+	firmware-name = "qcom/apq8016/mba.mbn", "qcom/apq8016/modem.mbn";
+};
+
+&pm8916_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pronto {
+	status = "okay";
+
+	firmware-name = "qcom/apq8016/wcnss.mbn";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
+&sound {
+	status = "okay";
+
+	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
+	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
+	pinctrl-names = "default", "sleep";
+	qcom,model = "DB410c";
+	qcom,audio-routing =
+		"AMIC2", "MIC BIAS Internal2",
+		"AMIC3", "MIC BIAS External1";
+
+	external-dai-link@0 {
+		link-name = "ADV7533";
+		cpu {
+			sound-dai = <&lpass MI2S_QUATERNARY>;
+		};
+		codec {
+			sound-dai = <&adv_bridge 0>;
+		};
+	};
+
+	internal-codec-playback-dai-link@0 {
+		link-name = "WCD";
+		cpu {
+			sound-dai = <&lpass MI2S_PRIMARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+		};
+	};
+
+	internal-codec-capture-dai-link@0 {
+		link-name = "WCD-Capture";
+		cpu {
+			sound-dai = <&lpass MI2S_TERTIARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&usb_id>, <&usb_id>;
+
+	pinctrl-names = "default", "device";
+	pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+	pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+};
+
+&usb_hs_phy {
+	extcon = <&usb_id>;
+};
+
+&wcd_codec {
+	clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
+	clock-names = "mclk";
+	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+};
+
+&wcnss_ctrl {
+	firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
+};
+
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&stm { status = "okay"; };
+&tpiu { status = "okay"; };
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <1250000>;
+		regulator-max-microvolt = <1350000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1850000>;
+		regulator-max-microvolt = <2150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/*
+	 * The 96Boards specification expects a 1.8V power rail on the low-speed
+	 * expansion connector that is able to provide at least 0.18W / 100 mA.
+	 * L15/L16 are connected in parallel to provide 55 mA each. A minimum load
+	 * must be specified to ensure the regulators are not put in LPM where they
+	 * would only provide 5 mA.
+	 */
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-system-load = <50000>;
+		regulator-allow-set-load;
+		regulator-always-on;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-system-load = <50000>;
+		regulator-allow-set-load;
+		regulator-always-on;
+	};
+
+	l17 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
+
+/*
+ * 2mA drive strength is not enough when connecting multiple
+ * I2C devices with different pull up resistors.
+ */
+&i2c2_default {
+	drive-strength = <16>;
+};
+
+&i2c4_default {
+	drive-strength = <16>;
+};
+
+&i2c6_default {
+	drive-strength = <16>;
+};
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ *         NC = not connected (pin out but not routed from the chip to
+ *              anything the board)
+ *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ *         LSEC = Low Speed External Connector
+ *         HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "DragonBoard410c"
+ * dated monday, august 31, 2015. Page 5 in particular.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+
+&msmgpio {
+	gpio-line-names =
+		"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
+		"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
+		"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
+		"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
+		"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
+		"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
+		"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
+		"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
+		"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
+		"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
+		"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
+		"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
+		"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
+		"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
+		"[I2C3_SDA]", /* HSEC pin 38 */
+		"[I2C3_SCL]", /* HSEC pin 36 */
+		"[SPI0_MOSI]", /* LSEC pin 14 */
+		"[SPI0_MISO]", /* LSEC pin 10 */
+		"[SPI0_CS_N]", /* LSEC pin 12 */
+		"[SPI0_CLK]", /* LSEC pin 8 */
+		"HDMI_HPD_N", /* GPIO 20 */
+		"USR_LED_1_CTRL",
+		"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
+		"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
+		"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
+		"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
+		"[CSI0_MCLK]", /* HSEC pin 15 */
+		"[CSI1_MCLK]", /* HSEC pin 17 */
+		"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
+		"[I2C2_SDA]", /* HSEC pin 34 */
+		"[I2C2_SCL]", /* HSEC pin 32 */
+		"DSI2HDMI_INT_N",
+		"DSI_SW_SEL_APQ",
+		"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
+		"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
+		"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
+		"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
+		"FORCED_USB_BOOT",
+		"SD_CARD_DET_N",
+		"[WCSS_BT_SSBI]",
+		"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
+		"[WCSS_WLAN_DATA_1]",
+		"[WCSS_WLAN_DATA_0]",
+		"[WCSS_WLAN_SET]",
+		"[WCSS_WLAN_CLK]",
+		"[WCSS_FM_SSBI]",
+		"[WCSS_FM_SDI]",
+		"[WCSS_BT_DAT_CTL]",
+		"[WCSS_BT_DAT_STB]",
+		"NC",
+		"NC", /* GPIO 50 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 60 */
+		"NC",
+		"NC",
+		"[CDC_PDM0_CLK]",
+		"[CDC_PDM0_SYNC]",
+		"[CDC_PDM0_TX0]",
+		"[CDC_PDM0_RX0]",
+		"[CDC_PDM0_RX1]",
+		"[CDC_PDM0_RX2]",
+		"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
+		"NC", /* GPIO 70 */
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 74 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"BOOT_CONFIG_0", /* GPIO 80 */
+		"BOOT_CONFIG_1",
+		"BOOT_CONFIG_2",
+		"BOOT_CONFIG_3",
+		"NC",
+		"NC",
+		"BOOT_CONFIG_5",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 90 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 100 */
+		"NC",
+		"NC",
+		"NC",
+		"SSBI_GPS",
+		"NC",
+		"NC",
+		"KEY_VOLP_N",
+		"NC",
+		"NC",
+		"[LS_EXP_MI2S_WS]", /* GPIO 110 */
+		"NC",
+		"NC",
+		"[LS_EXP_MI2S_SCK]",
+		"[LS_EXP_MI2S_DATA0]",
+		"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
+		"NC",
+		"[DSI2HDMI_MI2S_WS]",
+		"[DSI2HDMI_MI2S_SCK]",
+		"[DSI2HDMI_MI2S_DATA0]",
+		"USR_LED_2_CTRL", /* GPIO 120 */
+		"SB_HS_ID";
+
+	msmgpio_leds: msmgpio-leds {
+		pins = "gpio21", "gpio120";
+		function = "gpio";
+
+		output-low;
+	};
+
+	usb_id_default: usb-id-default {
+		pins = "gpio121";
+		function = "gpio";
+
+		drive-strength = <8>;
+		input-enable;
+		bias-pull-up;
+	};
+
+	adv7533_int_active: adv533-int-active {
+		pins = "gpio31";
+		function = "gpio";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	adv7533_int_suspend: adv7533-int-suspend {
+		pins = "gpio31";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	adv7533_switch_active: adv7533-switch-active {
+		pins = "gpio32";
+		function = "gpio";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	adv7533_switch_suspend: adv7533-switch-suspend {
+		pins = "gpio32";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_key_volp_n_default: msm-key-volp-n-default {
+		pins = "gpio107";
+		function = "gpio";
+
+		drive-strength = <8>;
+		input-enable;
+		bias-pull-up;
+	};
+};
+
+&pm8916_gpios {
+	gpio-line-names =
+		"USR_LED_3_CTRL",
+		"USR_LED_4_CTRL",
+		"USB_HUB_RESET_N_PM",
+		"USB_SW_SEL_PM";
+
+	usb_hub_reset_pm: usb-hub-reset-pm {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		input-disable;
+		output-high;
+	};
+
+	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		output-low;
+	};
+
+	usb_sw_sel_pm: usb-sw-sel-pm {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		power-source = <PM8916_GPIO_VPH>;
+		input-disable;
+		output-high;
+	};
+
+	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		power-source = <PM8916_GPIO_VPH>;
+		input-disable;
+		output-low;
+	};
+
+	pm8916_gpios_leds: pm8916-gpios-leds {
+		pins = "gpio1", "gpio2";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		output-low;
+	};
+};
+
+&pm8916_mpps {
+	gpio-line-names =
+		"VDD_PX_BIAS",
+		"WLAN_LED_CTRL",
+		"BT_LED_CTRL",
+		"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f>;
+
+	ls_exp_gpio_f: pm8916-mpp4-state {
+		pins = "mpp4";
+		function = "digital";
+
+		output-low;
+		power-source = <PM8916_MPP_L5>;	// 1.8V
+	};
+
+	pm8916_mpps_leds: pm8916-mpps-state {
+		pins = "mpp2", "mpp3";
+		function = "digital";
+
+		output-low;
+	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
@@ -5,9 +5,1077 @@
 
 /dts-v1/;
 
-#include "apq8096-db820c.dtsi"
+#include "msm8996.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ *         NC      = not connected (pin out but not routed from the chip to
+ *                   anything the board)
+ *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ *         LSEC    = Low Speed External Connector
+ *         P HSEC  = Primary High Speed External Connector
+ *         S HSEC  = Secondary High Speed External Connector
+ *         J14     = Camera Connector
+ *         TP      = Test Points
+ *
+ * Line names are taken from the schematic "DragonBoard 820c",
+ * drawing no: LM25-P2751-1
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
 
 / {
 	model = "Qualcomm Technologies, Inc. DB820c";
 	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+		serial1 = &blsp2_uart3;
+		serial2 = &blsp1_uart2;
+		i2c0	= &blsp1_i2c3;
+		i2c1	= &blsp2_i2c1;
+		i2c2	= &blsp2_i2c1;
+		spi0	= &blsp1_spi1;
+		spi1	= &blsp2_spi6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		divclk4: divclk4 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "divclk4";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&divclk4_pin_a>;
+		};
+
+		div1_mclk: divclk1 {
+			compatible = "gpio-gate-clock";
+			pinctrl-0 = <&audio_mclk>;
+			pinctrl-names = "default";
+			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+			#clock-cells = <0>;
+			enable-gpios = <&pm8994_gpios 15 0>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_up_gpio>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	usb2_id: usb2-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_det_gpio>;
+	};
+
+	usb3_id: usb3-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_vbus_det_gpio>;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	wlan_en: wlan-en-1-8v {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_gpios>;
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8994_gpios 8 0>;
+
+		/* WLAN card specific delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+};
+
+&blsp1_i2c3 {
+	/* On Low speed expansion */
+	label = "LS-I2C0";
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	/* On Low speed expansion */
+	label = "LS-SPI0";
+	status = "okay";
+};
+
+&blsp1_uart2 {
+	label = "BT-UART";
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,qca6174-bt";
+
+		/* bt_disable_n gpio */
+		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+
+		clocks = <&divclk4>;
+	};
+};
+
+&adsp_pil {
+	status = "okay";
+};
+
+&blsp2_i2c1 {
+	/* On High speed expansion */
+	label = "HS-I2C2";
+	status = "okay";
+};
+
+&blsp2_i2c1 {
+	/* On Low speed expansion */
+	label = "LS-I2C1";
+	status = "okay";
+};
+
+&blsp2_spi6 {
+	/* On High speed expansion */
+	label = "HS-SPI1";
+	status = "okay";
+};
+
+&blsp2_uart2 {
+	label = "LS-UART1";
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart2_2pins_default>;
+	pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
+};
+
+&blsp2_uart3 {
+	label = "LS-UART0";
+	status = "disabled";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart3_4pins_default>;
+	pinctrl-1 = <&blsp2_uart3_4pins_sleep>;
+};
+
+&camss {
+	vdda-supply = <&vreg_l2a_1p25>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+	pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
+
+	core-vdda-supply = <&vreg_l12a_1p8>;
+	core-vcc-supply = <&vreg_s4a_1p8>;
+};
+
+&hdmi_phy {
+	status = "okay";
+
+	vddio-supply = <&vreg_l12a_1p8>;
+	vcca-supply = <&vreg_l28a_0p925>;
+	#phy-cells = <0>;
+};
+
+&hsusb_phy1 {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&hsusb_phy2 {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mmcc {
+	vdd-gfx-supply = <&vdd_gfx>;
+};
+
+&pm8994_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&tlmm {
+	gpio-line-names =
+		"[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
+		"[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
+		"[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
+		"[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
+		"[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
+		"[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
+		"[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
+		"[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
+		"GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
+		"TP93", /* GPIO_9 */
+		"GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
+		"[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
+		"NC", /* GPIO_12 */
+		"[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
+		"[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
+		"[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
+		"TP99", /* GPIO_16 */
+		"[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
+		"[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
+		"[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
+		"[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
+		"FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
+		"FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
+		"GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
+		"GPIO-D", /* GPIO_24, LSEC pin 26 */
+		"GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
+		"GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
+		"BLSP6_I2C_SDA", /* GPIO_27 */
+		"BLSP6_I2C_SCL", /* GPIO_28 */
+		"GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
+		"GPIO30", /* GPIO_30, S HSEC pin 4 */
+		"HDMI_CEC", /* GPIO_31 */
+		"HDMI_DDC_CLOCK", /* GPIO_32 */
+		"HDMI_DDC_DATA", /* GPIO_33 */
+		"HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
+		"PCIE0_RST_N", /* GPIO_35 */
+		"PCIE0_CLKREQ_N", /* GPIO_36 */
+		"PCIE0_WAKE", /* GPIO_37 */
+		"SD_CARD_DET_N", /* GPIO_38 */
+		"TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
+		"W_DISABLE_N", /* GPIO_40 */
+		"[BLSP9_UART_TX]", /* GPIO_41 */
+		"[BLSP9_UART_RX]", /* GPIO_42 */
+		"[BLSP2_UART_CTS_N]", /* GPIO_43 */
+		"[BLSP2_UART_RFR_N]", /* GPIO_44 */
+		"[BLSP3_UART_TX]", /* GPIO_45 */
+		"[BLSP3_UART_RX]", /* GPIO_46 */
+		"[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
+		"[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
+		"[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
+		"[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
+		"[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
+		"[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
+		"[CODEC_INT1_N]", /* GPIO_53 */
+		"[CODEC_INT2_N]", /* GPIO_54 */
+		"[BLSP7_I2C_SDA]", /* GPIO_55 */
+		"[BLSP7_I2C_SCL]", /* GPIO_56 */
+		"MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
+		"[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
+		"[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
+		"[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
+		"[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
+		"GPIO-E", /* GPIO_62, LSEC pin 27 */
+		"TP87", /* GPIO_63 */
+		"[CODEC_RST_N]", /* GPIO_64 */
+		"[PCM1_CLK]", /* GPIO_65 */
+		"[PCM1_SYNC]", /* GPIO_66 */
+		"[PCM1_DIN]", /* GPIO_67 */
+		"[PCM1_DOUT]", /* GPIO_68 */
+		"AUDIO_REF_CLK", /* GPIO_69 */
+		"SLIMBUS_CLK", /* GPIO_70 */
+		"SLIMBUS_DATA0", /* GPIO_71 */
+		"SLIMBUS_DATA1", /* GPIO_72 */
+		"NC", /* GPIO_73 */
+		"NC", /* GPIO_74 */
+		"NC", /* GPIO_75 */
+		"NC", /* GPIO_76 */
+		"TP94", /* GPIO_77 */
+		"NC", /* GPIO_78 */
+		"TP95", /* GPIO_79 */
+		"GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
+		"TP88", /* GPIO_81 */
+		"TP89", /* GPIO_82 */
+		"TP90", /* GPIO_83 */
+		"TP91", /* GPIO_84 */
+		"[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
+		"[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
+		"[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
+		"[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
+		"TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
+		"TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
+		"TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
+		"NC", /* GPIO_92 */
+		"TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
+		"TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
+		"TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
+		"TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
+		"NC", /* GPIO_97 */
+		"CAM1_STANDBY_N", /* GPIO_98 */
+		"NC", /* GPIO_99 */
+		"NC", /* GPIO_100 */
+		"[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
+		"BOOT_CONFIG1", /* GPIO_102 */
+		"USB_HUB_RESET", /* GPIO_103 */
+		"CAM1_RST_N", /* GPIO_104 */
+		"NC", /* GPIO_105 */
+		"NC", /* GPIO_106 */
+		"NC", /* GPIO_107 */
+		"NC", /* GPIO_108 */
+		"NC", /* GPIO_109 */
+		"NC", /* GPIO_110 */
+		"NC", /* GPIO_111 */
+		"NC", /* GPIO_112 */
+		"PMI8994_BUA", /* GPIO_113 */
+		"PCIE2_RST_N", /* GPIO_114 */
+		"PCIE2_CLKREQ_N", /* GPIO_115 */
+		"PCIE2_WAKE", /* GPIO_116 */
+		"SSC_IRQ_0", /* GPIO_117 */
+		"SSC_IRQ_1", /* GPIO_118 */
+		"SSC_IRQ_2", /* GPIO_119 */
+		"NC", /* GPIO_120 */
+		"GPIO121", /* GPIO_121, S HSEC pin 2 */
+		"NC", /* GPIO_122 */
+		"SSC_IRQ_6", /* GPIO_123 */
+		"SSC_IRQ_7", /* GPIO_124 */
+		"GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
+		"BOOT_CONFIG5", /* GPIO_126 */
+		"NC", /* GPIO_127 */
+		"NC", /* GPIO_128 */
+		"BOOT_CONFIG7", /* GPIO_129 */
+		"PCIE1_RST_N", /* GPIO_130 */
+		"PCIE1_CLKREQ_N", /* GPIO_131 */
+		"PCIE1_WAKE", /* GPIO_132 */
+		"GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
+		"NC", /* GPIO_134 */
+		"NC", /* GPIO_135 */
+		"BOOT_CONFIG8", /* GPIO_136 */
+		"NC", /* GPIO_137 */
+		"NC", /* GPIO_138 */
+		"GPS_SSBI2", /* GPIO_139 */
+		"GPS_SSBI1", /* GPIO_140 */
+		"NC", /* GPIO_141 */
+		"NC", /* GPIO_142 */
+		"NC", /* GPIO_143 */
+		"BOOT_CONFIG6", /* GPIO_144 */
+		"NC", /* GPIO_145 */
+		"NC", /* GPIO_146 */
+		"NC", /* GPIO_147 */
+		"NC", /* GPIO_148 */
+		"NC"; /* GPIO_149 */
+
+	sdc2_cd_on: sdc2_cd_on {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <16>;	/* 16 MA */
+		};
+	};
+
+	sdc2_cd_off: sdc2_cd_off {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+	};
+
+	hdmi_hpd_active: hdmi_hpd_active {
+		mux {
+			pins = "gpio34";
+			function = "hdmi_hot";
+		};
+
+		config {
+			pins = "gpio34";
+			bias-pull-down;
+			drive-strength = <16>;
+		};
+	};
+
+	hdmi_hpd_suspend: hdmi_hpd_suspend {
+		mux {
+			pins = "gpio34";
+			function = "hdmi_hot";
+		};
+
+		config {
+			pins = "gpio34";
+			bias-pull-down;
+			drive-strength = <2>;
+		};
+	};
+
+	hdmi_ddc_active: hdmi_ddc_active {
+		mux {
+			pins = "gpio32", "gpio33";
+			function = "hdmi_ddc";
+		};
+
+		config {
+			pins = "gpio32", "gpio33";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	hdmi_ddc_suspend: hdmi_ddc_suspend {
+		mux {
+			pins = "gpio32", "gpio33";
+			function = "hdmi_ddc";
+		};
+
+		config {
+			pins = "gpio32", "gpio33";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	vddpe-3v3-supply = <&wlan_en>;
+	vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&tlmm 130 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie2 {
+	status = "okay";
+	perst-gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&pm8994_gpios {
+	gpio-line-names =
+		"NC",
+		"KEY_VOLP_N",
+		"NC",
+		"BL1_PWM",
+		"GPIO-F", /* BL0_PWM, LSEC pin 28 */
+		"BL1_EN",
+		"NC",
+		"WLAN_EN",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"DIVCLK1",
+		"DIVCLK2",
+		"DIVCLK3",
+		"DIVCLK4",
+		"BT_EN",
+		"PMIC_SLB",
+		"PMIC_BUA",
+		"USB_VBUS_DET";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
+
+	ls_exp_gpio_f: pm8994_gpio5 {
+		pinconf {
+			pins = "gpio5";
+			output-low;
+			power-source = <2>; // PM8994_GPIO_S4, 1.8V
+		};
+	};
+
+	bt_en_gpios: bt_en_gpios {
+		pinconf {
+			pins = "gpio19";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+			bias-pull-down;
+		};
+	};
+
+	wlan_en_gpios: wlan_en_gpios {
+		pinconf {
+			pins = "gpio8";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+			bias-pull-down;
+		};
+	};
+
+	audio_mclk: clk_div1 {
+		pinconf {
+			pins = "gpio15";
+			function = "func1";
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+
+	volume_up_gpio: pm8996_gpio2 {
+		pinconf {
+			pins = "gpio2";
+			function = "normal";
+			input-enable;
+			drive-push-pull;
+			bias-pull-up;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+
+	divclk4_pin_a: divclk4 {
+		pinconf {
+			pins = "gpio18";
+			function = PMIC_GPIO_FUNC_FUNC2;
+
+			bias-disable;
+			power-source = <PM8994_GPIO_S4>;
+		};
+	};
+
+	usb3_vbus_det_gpio: pm8996_gpio22 {
+		pinconf {
+			pins = "gpio22";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-enable;
+			bias-pull-down;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+};
+
+&pm8994_mpps {
+	gpio-line-names =
+		"VDDPX_BIAS",
+		"WIFI_LED",
+		"NC",
+		"BT_LED",
+		"PM_MPP05",
+		"PM_MPP06",
+		"PM_MPP07",
+		"NC";
+};
+
+&pm8994_spmi_regulators {
+	qcom,saw-reg = <&saw3>;
+	s9 {
+		qcom,saw-slave;
+	};
+	s10 {
+		qcom,saw-slave;
+	};
+	s11 {
+		qcom,saw-leader;
+		regulator-always-on;
+		regulator-min-microvolt = <980000>;
+		regulator-max-microvolt = <980000>;
+	};
+};
+
+&pmi8994_gpios {
+	gpio-line-names =
+		"NC",
+		"SPKR_AMP_EN1",
+		"SPKR_AMP_EN2",
+		"TP61",
+		"NC",
+		"USB2_VBUS_DET",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+
+	usb2_vbus_det_gpio: pmi8996_gpio6 {
+		pinconf {
+			pins = "gpio6";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-enable;
+			bias-pull-down;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+};
+
+&pmi8994_spmi_regulators {
+	vdd_gfx: s2@1700 {
+		reg = <0x1700 0x100>;
+		regulator-name = "VDD_GFX";
+		regulator-min-microvolt = <980000>;
+		regulator-max-microvolt = <980000>;
+	};
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		compatible = "qcom,rpm-pm8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_l1-supply = <&vreg_s1b_1p025>;
+		vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
+		vdd_l3_l11-supply = <&vreg_s3a_1p3>;
+		vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
+		vdd_l5_l7-supply = <&vreg_s5a_2p15>;
+		vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
+		vdd_l8_l16_l30-supply = <&vph_pwr>;
+		vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
+		vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
+		vdd_l14_l15-supply = <&vreg_s5a_2p15>;
+		vdd_l17_l29-supply = <&vph_pwr_bbyp>;
+		vdd_l20_l21-supply = <&vph_pwr_bbyp>;
+		vdd_l25-supply = <&vreg_s3a_1p3>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p3: s3 {
+			regulator-name = "vreg_s3a_1p3";
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		/**
+		 * 1.8v required on LS expansion
+		 * for mezzanine boards
+		 */
+		vreg_s4a_1p8: s4 {
+			regulator-name = "vreg_s4a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+		vreg_s5a_2p15: s5 {
+			regulator-name = "vreg_s5a_2p15";
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+		vreg_s7a_1p0: s7 {
+			regulator-name = "vreg_s7a_1p0";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l1a_1p0: l1 {
+			regulator-name = "vreg_l1a_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l2a_1p25: l2 {
+			regulator-name = "vreg_l2a_1p25";
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+		};
+		vreg_l3a_0p875: l3 {
+			regulator-name = "vreg_l3a_0p875";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <850000>;
+		};
+		vreg_l4a_1p225: l4 {
+			regulator-name = "vreg_l4a_1p225";
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		vreg_l6a_1p2: l6 {
+			regulator-name = "vreg_l6a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		vreg_l8a_1p8: l8 {
+			regulator-name = "vreg_l8a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l9a_1p8: l9 {
+			regulator-name = "vreg_l9a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l10a_1p8: l10 {
+			regulator-name = "vreg_l10a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l11a_1p15: l11 {
+			regulator-name = "vreg_l11a_1p15";
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+		vreg_l12a_1p8: l12 {
+			regulator-name = "vreg_l12a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l13a_2p95: l13 {
+			regulator-name = "vreg_l13a_2p95";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		vreg_l14a_1p8: l14 {
+			regulator-name = "vreg_l14a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l15a_1p8: l15 {
+			regulator-name = "vreg_l15a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l16a_2p7: l16 {
+			regulator-name = "vreg_l16a_2p7";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+		vreg_l17a_2p8: l17 {
+			regulator-name = "vreg_l17a_2p8";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+		};
+		vreg_l18a_2p85: l18 {
+			regulator-name = "vreg_l18a_2p85";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2900000>;
+		};
+		vreg_l19a_2p8: l19 {
+			regulator-name = "vreg_l19a_2p8";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		vreg_l20a_2p95: l20 {
+			regulator-name = "vreg_l20a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+		vreg_l21a_2p95: l21 {
+			regulator-name = "vreg_l21a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+			regulator-system-load = <200000>;
+		};
+		vreg_l22a_3p0: l22 {
+			regulator-name = "vreg_l22a_3p0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		vreg_l23a_2p8: l23 {
+			regulator-name = "vreg_l23a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l24a_3p075: l24 {
+			regulator-name = "vreg_l24a_3p075";
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		vreg_l25a_1p2: l25 {
+			regulator-name = "vreg_l25a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+		vreg_l26a_0p8: l27 {
+			regulator-name = "vreg_l26a_0p8";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l28a_0p925: l28 {
+			regulator-name = "vreg_l28a_0p925";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+			regulator-allow-set-load;
+		};
+		vreg_l29a_2p8: l29 {
+			regulator-name = "vreg_l29a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l30a_1p8: l30 {
+			regulator-name = "vreg_l30a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l32a_1p8: l32 {
+			regulator-name = "vreg_l32a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-name = "vreg_lvs1a_1p8";
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-name = "vreg_lvs2a_1p8";
+		};
+	};
+
+	pmi8994-regulators {
+		compatible = "qcom,rpm-pmi8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_bst_byp-supply = <&vph_pwr>;
+
+		vph_pwr_bbyp: boost-bypass {
+			regulator-name = "vph_pwr_bbyp";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		vreg_s1b_1p025: s1 {
+			regulator-name = "vreg_s1b_1p025";
+			regulator-min-microvolt = <1025000>;
+			regulator-max-microvolt = <1025000>;
+		};
+	};
+};
+
+&sdhc2 {
+	/* External SD card */
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+	status = "okay";
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&sound {
+	compatible = "qcom,apq8096-sndcard";
+	model = "DB820c";
+	audio-routing =	"RX_BIAS", "MCLK",
+		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL2",  "MultiMedia2 Playback",
+		"MultiMedia3 Capture", "MM_UL3";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	hdmi-dai-link {
+		link-name = "HDMI";
+		cpu {
+			sound-dai = <&q6afedai HDMI_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&hdmi 0>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_6_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+	};
+
+		codec {
+			sound-dai = <&wcd9335 6>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 1>;
+		};
+	};
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
+};
+
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l25a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+
+	vcc-max-microamp = <600000>;
+	vccq-max-microamp = <450000>;
+	vccq2-max-microamp = <450000>;
+};
+
+&usb2 {
+	status = "okay";
+	extcon = <&usb2_id>;
+
+	dwc3@7600000 {
+		extcon = <&usb2_id>;
+		dr_mode = "otg";
+		maximum-speed = "high-speed";
+	};
+};
+
+&usb3 {
+	status = "okay";
+	extcon = <&usb3_id>;
+
+	dwc3@6a00000 {
+		extcon = <&usb3_id>;
+		dr_mode = "otg";
+	};
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+
+};
+
+&venus {
+	status = "okay";
+};
+
+&wcd9335 {
+	clock-names = "mclk", "slimbus";
+	clocks = <&div1_mclk>,
+		 <&rpmcc RPM_SMD_BB_CLK1>;
+
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
@@ -26,7 +26,7 @@
 
 	v1p05: v1p05-regulator {
 		compatible = "regulator-fixed";
-		reglator-name = "v1p05";
+		regulator-name = "v1p05";
 		regulator-always-on;
 		regulator-boot-on;
 
@@ -38,7 +38,7 @@
 
 	v12_poe: v12-poe-regulator {
 		compatible = "regulator-fixed";
-		reglator-name = "v12_poe";
+		regulator-name = "v12_poe";
 		regulator-always-on;
 		regulator-boot-on;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -37,6 +37,8 @@
 
 &spi_0 {
 	cs-select = <0>;
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	m25p80@0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -129,12 +129,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x80>;
-		#hwlock-cells = <1>;
-	};
-
 	pmuv8: pmu {
 		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
@@ -175,7 +169,7 @@
 	smem {
 		compatible = "qcom,smem";
 		memory-region = <&smem_region>;
-		hwlocks = <&tcsr_mutex 0>;
+		hwlocks = <&tcsr_mutex 3>;
 	};
 
 	soc: soc {
@@ -200,7 +194,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <1>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			qcom,config-pipe-trust-reg = <0>;
 		};
 
@@ -221,7 +215,7 @@
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&tlmm 0 80>;
+			gpio-ranges = <&tlmm 0 0 80>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
@@ -253,9 +247,10 @@
 			#reset-cells = <1>;
 		};
 
-		tcsr_mutex_regs: syscon@1905000 {
-			compatible = "syscon";
-			reg = <0x0 0x01905000 0x0 0x8000>;
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,ipq6018-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0x0 0x01905000 0x0 0x20000>;
+			#hwlock-cells = <1>;
 		};
 
 		tcsr: syscon@1937000 {
@@ -401,7 +396,7 @@
 			reset-names = "phy",
 				      "common";
 
-			pcie_phy0: lane@84200 {
+			pcie_phy0: phy@84200 {
 				reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */
 				      <0x0 0x84400 0x0 0x200>, /* Serdes Rx */
 				      <0x0 0x84800 0x0 0x4f4>; /* PCS: Lane0, COM, PCIE */
@@ -433,10 +428,8 @@
 			phys = <&pcie_phy0>;
 			phy-names = "pciephy";
 
-			ranges = <0x81000000 0 0x20200000 0 0x20200000
-				  0 0x10000>, /* downstream I/O */
-				 <0x82000000 0 0x20220000 0 0x20220000
-				  0 0xfde0000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x0 0x20200000 0x0 0x10000>,
+				 <0x82000000 0x0 0x20220000 0x0 0x20220000 0x0 0xfde0000>;
 
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -60,11 +60,11 @@
 	perst-gpio = <&tlmm 58 0x1>;
 };
 
-&pcie_phy0 {
+&pcie_qmp0 {
 	status = "okay";
 };
 
-&pcie_phy1 {
+&pcie_qmp1 {
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -13,7 +13,7 @@
 	clocks {
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32000>;
+			clock-frequency = <32768>;
 			#clock-cells = <0>;
 		};
 
@@ -91,7 +91,6 @@
 		ssphy_1: phy@58000 {
 			compatible = "qcom,ipq8074-qmp-usb3-phy";
 			reg = <0x00058000 0x1c4>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -106,15 +105,16 @@
 			reset-names = "phy","common";
 			status = "disabled";
 
-			usb1_ssphy: lane@58200 {
+			usb1_ssphy: phy@58200 {
 				reg = <0x00058200 0x130>,       /* Tx */
 				      <0x00058400 0x200>,     /* Rx */
 				      <0x00058800 0x1f8>,     /* PCS  */
 				      <0x00058600 0x044>;     /* PCS misc*/
 				#phy-cells = <0>;
+				#clock-cells = <1>;
 				clocks = <&gcc GCC_USB1_PIPE_CLK>;
 				clock-names = "pipe0";
-				clock-output-names = "gcc_usb1_pipe_clk_src";
+				clock-output-names = "usb3phy_1_cc_pipe_clk";
 			};
 		};
 
@@ -134,7 +134,6 @@
 		ssphy_0: phy@78000 {
 			compatible = "qcom,ipq8074-qmp-usb3-phy";
 			reg = <0x00078000 0x1c4>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -149,15 +148,16 @@
 			reset-names = "phy","common";
 			status = "disabled";
 
-			usb0_ssphy: lane@78200 {
+			usb0_ssphy: phy@78200 {
 				reg = <0x00078200 0x130>,       /* Tx */
 				      <0x00078400 0x200>,     /* Rx */
 				      <0x00078800 0x1f8>,     /* PCS  */
 				      <0x00078600 0x044>;     /* PCS misc*/
 				#phy-cells = <0>;
+				#clock-cells = <1>;
 				clocks = <&gcc GCC_USB0_PIPE_CLK>;
 				clock-names = "pipe0";
-				clock-output-names = "gcc_usb0_pipe_clk_src";
+				clock-output-names = "usb3phy_0_cc_pipe_clk";
 			};
 		};
 
@@ -174,34 +174,61 @@
 			status = "disabled";
 		};
 
-		pcie_phy0: phy@86000 {
-			compatible = "qcom,ipq8074-qmp-pcie-phy";
-			reg = <0x00086000 0x1000>;
-			#phy-cells = <0>;
-			clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
-			clock-names = "pipe_clk";
-			clock-output-names = "pcie20_phy0_pipe_clk";
+		pcie_qmp0: phy@84000 {
+			compatible = "qcom,ipq8074-qmp-gen3-pcie-phy";
+			reg = <0x00084000 0x1bc>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 
+			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+				<&gcc GCC_PCIE0_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
 			resets = <&gcc GCC_PCIE0_PHY_BCR>,
 				<&gcc GCC_PCIE0PHY_PHY_BCR>;
 			reset-names = "phy",
 				      "common";
 			status = "disabled";
+
+			pcie_phy0: phy@84200 {
+				reg = <0x84200 0x16c>,
+				      <0x84400 0x200>,
+				      <0x84800 0x1f0>,
+				      <0x84c00 0xf4>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "pcie20_phy0_pipe_clk";
+			};
 		};
 
-		pcie_phy1: phy@8e000 {
+		pcie_qmp1: phy@8e000 {
 			compatible = "qcom,ipq8074-qmp-pcie-phy";
-			reg = <0x0008e000 0x1000>;
-			#phy-cells = <0>;
-			clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
-			clock-names = "pipe_clk";
-			clock-output-names = "pcie20_phy1_pipe_clk";
+			reg = <0x0008e000 0x1c4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 
+			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+				<&gcc GCC_PCIE1_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
 			resets = <&gcc GCC_PCIE1_PHY_BCR>,
 				<&gcc GCC_PCIE1PHY_PHY_BCR>;
 			reset-names = "phy",
 				      "common";
 			status = "disabled";
+
+			pcie_phy1: phy@8e200 {
+				reg = <0x8e200 0x130>,
+				      <0x8e400 0x200>,
+				      <0x8e800 0x1f8>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "pcie20_phy1_pipe_clk";
+			};
 		};
 
 		prng: rng@e3000 {
@@ -220,7 +247,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <1>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			status = "disabled";
 		};
 
@@ -437,7 +464,7 @@
 			status = "disabled";
 		};
 
-		qpic_nand: nand@79b0000 {
+		qpic_nand: nand-controller@79b0000 {
 			compatible = "qcom,ipq8074-nand";
 			reg = <0x079b0000 0x10000>;
 			#address-cells = <1>;
@@ -487,6 +514,7 @@
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&qusb_phy_0>, <&usb0_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+				snps,parkmode-disable-ss-quirk;
 				snps,is-utmi-l1-suspend;
 				snps,hird-threshold = /bits/ 8 <0x0>;
 				snps,dis_u2_susphy_quirk;
@@ -527,6 +555,7 @@
 				interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&qusb_phy_1>, <&usb1_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+				snps,parkmode-disable-ss-quirk;
 				snps,is-utmi-l1-suspend;
 				snps,hird-threshold = /bits/ 8 <0x0>;
 				snps,dis_u2_susphy_quirk;
@@ -634,10 +663,8 @@
 			phys = <&pcie_phy1>;
 			phy-names = "pciephy";
 
-			ranges = <0x81000000 0 0x10200000 0x10200000
-				  0 0x100000   /* downstream I/O */
-				  0x82000000 0 0x10300000 0x10300000
-				  0 0xd00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x10200000 0x0 0x10000>,   /* I/O */
+				 <0x82000000 0x0 0x10220000 0x10220000 0x0 0xfde0000>; /* MEM */
 
 			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
@@ -680,26 +707,26 @@
 		};
 
 		pcie0: pci@20000000 {
-			compatible = "qcom,pcie-ipq8074";
+			compatible = "qcom,pcie-ipq8074-gen3";
 			reg = <0x20000000 0xf1d>,
 			      <0x20000f20 0xa8>,
-			      <0x00080000 0x2000>,
+			      <0x20001000 0x1000>,
+			      <0x00080000 0x4000>,
 			      <0x20100000 0x1000>;
-			reg-names = "dbi", "elbi", "parf", "config";
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
 			device_type = "pci";
 			linux,pci-domain = <0>;
 			bus-range = <0x00 0xff>;
 			num-lanes = <1>;
+			max-link-speed = <3>;
 			#address-cells = <3>;
 			#size-cells = <2>;
 
 			phys = <&pcie_phy0>;
 			phy-names = "pciephy";
 
-			ranges = <0x81000000 0 0x20200000 0x20200000
-				  0 0x100000   /* downstream I/O */
-				  0x82000000 0 0x20300000 0x20300000
-				  0 0xd00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x20200000 0x0 0x10000>,   /* I/O */
+				 <0x82000000 0x0 0x20220000 0x20220000 0x0 0xfde0000>; /* MEM */
 
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
@@ -717,28 +744,30 @@
 			clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
 				 <&gcc GCC_PCIE0_AXI_M_CLK>,
 				 <&gcc GCC_PCIE0_AXI_S_CLK>,
-				 <&gcc GCC_PCIE0_AHB_CLK>,
-				 <&gcc GCC_PCIE0_AUX_CLK>;
-
+				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE0_RCHNG_CLK>;
 			clock-names = "iface",
 				      "axi_m",
 				      "axi_s",
-				      "ahb",
-				      "aux";
+				      "axi_bridge",
+				      "rchng";
+
 			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
 				 <&gcc GCC_PCIE0_SLEEP_ARES>,
 				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
 				 <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
 				 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
 				 <&gcc GCC_PCIE0_AHB_ARES>,
-				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>;
+				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
 			reset-names = "pipe",
 				      "sleep",
 				      "sticky",
 				      "axi_m",
 				      "axi_s",
 				      "ahb",
-				      "axi_m_sticky";
+				      "axi_m_sticky",
+				      "axi_s_sticky";
 			status = "disabled";
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
@@ -5,9 +5,22 @@
 
 /dts-v1/;
 
-#include "msm8916-mtp.dtsi"
+#include "msm8916-pm8916.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM 8916 MTP";
 	compatible = "qcom,msm8916-mtp", "qcom,msm8916-mtp/1", "qcom,msm8916";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		usid0 = &pm8916_0;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -19,8 +19,8 @@
 	#size-cells = <2>;
 
 	aliases {
-		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
-		sdhc2 = &sdhc_2; /* SDC2 SD card slot */
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
 	};
 
 	chosen { };
@@ -105,7 +105,7 @@
 		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <32768>;
+			clock-frequency = <32764>;
 		};
 	};
 
@@ -445,7 +445,7 @@
 			};
 		};
 
-		rpm_msg_ram: memory@60000 {
+		rpm_msg_ram: sram@60000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00060000 0x8000>;
 		};
@@ -1064,7 +1064,7 @@
 			};
 		};
 
-		camss: camss@1b00000 {
+		camss: camss@1b0ac00 {
 			compatible = "qcom,msm8916-camss";
 			reg = <0x01b0ac00 0x200>,
 				<0x01b00030 0x4>,
@@ -1233,7 +1233,7 @@
 			#size-cells = <1>;
 			#iommu-cells = <1>;
 			compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
-			ranges = <0 0x01e20000 0x40000>;
+			ranges = <0 0x01e20000 0x20000>;
 			reg = <0x01ef0000 0x3000>;
 			clocks = <&gcc GCC_SMMU_CFG_CLK>,
 				 <&gcc GCC_APSS_TCU_CLK>;
@@ -1307,7 +1307,7 @@
 		};
 
 		mpss: remoteproc@4080000 {
-			compatible = "qcom,msm8916-mss-pil", "qcom,q6v5-pil";
+			compatible = "qcom,msm8916-mss-pil";
 			reg = <0x04080000 0x100>,
 			      <0x04020000 0x040>;
 
@@ -1384,11 +1384,17 @@
 		lpass: audio-controller@7708000 {
 			status = "disabled";
 			compatible = "qcom,lpass-cpu-apq8016";
+
+			/*
+			 * Note: Unlike the name would suggest, the SEC_I2S_CLK
+			 * is actually only used by Tertiary MI2S while
+			 * Primary/Secondary MI2S both use the PRI_I2S_CLK.
+			 */
 			clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
 				 <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
 				 <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>,
 				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
-				 <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
+				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
 				 <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
 				 <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>;
 
@@ -1741,8 +1747,8 @@
 					<&rpmpd MSM8916_VDDMX>;
 			power-domain-names = "cx", "mx";
 
-			qcom,state = <&wcnss_smp2p_out 0>;
-			qcom,state-names = "stop";
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&wcnss_pin_a>;
@@ -1765,7 +1771,7 @@
 
 				label = "pronto";
 
-				wcnss {
+				wcnss_ctrl: wcnss {
 					compatible = "qcom,wcnss";
 					qcom,smd-channels = "WCNSS_CTRL";
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
@@ -1,7 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /* Copyright (c) 2015, LGE Inc. All rights reserved.
  * Copyright (c) 2016, The Linux Foundation. All rights reserved.
- * Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
+ * Copyright (c) 2021-2022, Petr Vorel <petr.vorel@gmail.com>
+ * Copyright (c) 2022, Dominik Kobinski <dominikkobinski314@gmail.com>
  */
 
 /dts-v1/;
@@ -13,6 +14,9 @@
 /* cont_splash_mem has different memory mapping */
 /delete-node/ &cont_splash_mem;
 
+/* disabled on downstream, conflicts with cont_splash_mem */
+/delete-node/ &dfps_data_mem;
+
 / {
 	model = "LG Nexus 5X";
 	compatible = "lg,bullhead", "qcom,msm8992";
@@ -47,7 +51,17 @@
 		};
 
 		cont_splash_mem: memory@3400000 {
-			reg = <0 0x03400000 0 0x1200000>;
+			reg = <0 0x03400000 0 0xc00000>;
+			no-map;
+		};
+
+		reserved@5000000 {
+			reg = <0x0 0x05000000 0x0 0x1a00000>;
+			no-map;
+		};
+
+		reserved@6c00000 {
+			reg = <0x0 0x06c00000 0x0 0x400000>;
 			no-map;
 		};
 	};
@@ -74,7 +88,7 @@
 		vdd_l17_29-supply = <&vph_pwr>;
 		vdd_l20_21-supply = <&vph_pwr>;
 		vdd_l25-supply = <&pm8994_s5>;
-		vdd_lvs1_2 = <&pm8994_s4>;
+		vdd_lvs1_2-supply = <&pm8994_s4>;
 
 		/* S1, S2, S6 and S12 are managed by RPMPD */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
@@ -11,6 +11,12 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/gpio-keys.h>
 
+/delete-node/ &adsp_mem;
+/delete-node/ &audio_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &peripheral_region;
+/delete-node/ &rmtfs_mem;
+
 / {
 	model = "Xiaomi Mi 4C";
 	compatible = "xiaomi,libra", "qcom,msm8992";
@@ -60,25 +66,62 @@
 		#size-cells = <2>;
 		ranges;
 
-		/* This is for getting crash logs using Android downstream kernels */
-		ramoops@dfc00000 {
-			compatible = "ramoops";
-			reg = <0x0 0xdfc00000 0x0 0x40000>;
-			console-size = <0x10000>;
-			record-size = <0x10000>;
-			ftrace-size = <0x10000>;
-			pmsg-size = <0x20000>;
+		memory_hole: hole@6400000 {
+			reg = <0 0x06400000 0 0x600000>;
+			no-map;
 		};
 
-		modem_region: modem_region@9000000 {
-			reg = <0x0 0x9000000 0x0 0x5a00000>;
+		memory_hole2: hole2@6c00000 {
+			reg = <0 0x06c00000 0 0x2400000>;
 			no-map;
 		};
 
-		tzapp: modem_region@ea00000 {
-			reg = <0x0 0xea00000 0x0 0x1900000>;
+		mpss_mem: mpss@9000000 {
+			reg = <0 0x09000000 0 0x5a00000>;
 			no-map;
 		};
+
+		tzapp: tzapp@ea00000 {
+			reg = <0 0x0ea00000 0 0x1900000>;
+			no-map;
+		};
+
+		mdm_rfsa_mem: mdm-rfsa@ca0b0000 {
+			reg = <0 0xca0b0000 0 0x10000>;
+			no-map;
+		};
+
+		rmtfs_mem: rmtfs@ca100000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xca100000 0 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+
+		qseecom_mem: qseecom@cb400000 {
+			reg = <0 0xcb400000 0 0x1c00000>;
+			no-mem;
+		};
+
+		adsp_rfsa_mem: adsp-rfsa@cd000000 {
+			reg = <0 0xcd000000 0 0x10000>;
+			no-map;
+		};
+
+		sensor_rfsa_mem: sensor-rfsa@cd010000 {
+			reg = <0 0xcd010000 0 0x10000>;
+			no-map;
+		};
+
+		ramoops@dfc00000 {
+			compatible = "ramoops";
+			reg = <0 0xdfc00000 0 0x40000>;
+			console-size = <0x10000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x20000>;
+		};
 	};
 };
 
@@ -120,9 +163,21 @@
 	status = "okay";
 };
 
-&peripheral_region {
-	reg = <0x0 0x7400000 0x0 0x1c00000>;
-	no-map;
+&pm8994_spmi_regulators {
+	VDD_APC0: s8 {
+		regulator-min-microvolt = <680000>;
+		regulator-max-microvolt = <1180000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* APC1 is 3-phase, but quoting downstream, s11 is "the gang leader" */
+	VDD_APC1: s11 {
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1225000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &rpm_requests {
@@ -142,7 +197,7 @@
 		vdd_l17_29-supply = <&vph_pwr>;
 		vdd_l20_21-supply = <&vph_pwr>;
 		vdd_l25-supply = <&pm8994_s5>;
-		vdd_lvs1_2 = <&pm8994_s4>;
+		vdd_lvs1_2-supply = <&pm8994_s4>;
 
 		/* S1, S2, S6 and S12 are managed by RPMPD */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -14,10 +14,6 @@
 	compatible = "qcom,rpmcc-msm8992";
 };
 
-&tcsr_mutex {
-	compatible = "qcom,sfpb-mutex";
-};
-
 &timer {
 	interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
@@ -540,8 +540,7 @@
 };
 
 &pmi8994_spmi_regulators {
-	vdd_gfx: s2@1700 {
-		reg = <0x1700 0x100>;
+	vdd_gfx: s2 {
 		regulator-min-microvolt = <980000>;
 		regulator-max-microvolt = <980000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
@@ -183,8 +183,7 @@
 	 * power domain.. which still isn't enough and forces us to bind
 	 * OXILI_CX and OXILI_GX together!
 	 */
-	vdd_gfx: s2@1700 {
-		reg = <0x1700 0x100>;
+	vdd_gfx: s2 {
 		regulator-name = "VDD_GFX";
 		regulator-min-microvolt = <980000>;
 		regulator-max-microvolt = <980000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -25,7 +25,7 @@
 		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <32768>;
+			clock-frequency = <32764>;
 			clock-output-names = "sleep_clk";
 		};
 	};
@@ -93,7 +93,7 @@
 		CPU6: cpu@102 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57";
-			reg = <0x0 0x101>;
+			reg = <0x0 0x102>;
 			enable-method = "psci";
 			next-level-cache = <&L2_1>;
 		};
@@ -101,7 +101,7 @@
 		CPU7: cpu@103 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57";
-			reg = <0x0 0x101>;
+			reg = <0x0 0x103>;
 			enable-method = "psci";
 			next-level-cache = <&L2_1>;
 		};
@@ -183,8 +183,8 @@
 			no-map;
 		};
 
-		cont_splash_mem: memory@3800000 {
-			reg = <0 0x03800000 0 0x2400000>;
+		cont_splash_mem: memory@3401000 {
+			reg = <0 0x03401000 0 0x2200000>;
 			no-map;
 		};
 
@@ -419,6 +419,15 @@
 			#size-cells = <1>;
 			ranges;
 
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "qusb2_phy",
+					  "hs_phy_irq",
+					  "ss_phy_irq";
+
 			clocks = <&gcc GCC_USB30_MASTER_CLK>,
 				 <&gcc GCC_SYS_NOC_USB3_AXI_CLK>,
 				 <&gcc GCC_USB30_SLEEP_CLK>,
@@ -498,7 +507,7 @@
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			qcom,controlled-remotely;
-			num-channels = <18>;
+			num-channels = <24>;
 			qcom,num-ees = <4>;
 		};
 
@@ -634,7 +643,7 @@
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			qcom,controlled-remotely;
-			num-channels = <18>;
+			num-channels = <24>;
 			qcom,num-ees = <4>;
 		};
 
@@ -715,7 +724,7 @@
 			reg = <0xfc400000 0x2000>;
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
@@ -725,7 +734,7 @@
 			reg = <0xfc4ab000 0x4>;
 		};
 
-		spmi_bus: spmi@fc4c0000 {
+		spmi_bus: spmi@fc4cf000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0xfc4cf000 0x1000>,
 			      <0xfc4cb000 0x1000>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
@@ -5,9 +5,31 @@
 
 /dts-v1/;
 
-#include "msm8996-mtp.dtsi"
+#include "msm8996.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM 8996 MTP";
 	compatible = "qcom,msm8996-mtp";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		serial@75b0000 {
+			status = "okay";
+		};
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_phy {
+	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
@@ -620,6 +620,7 @@
 &pmi8994_wled {
 	status = "okay";
 	default-brightness = <512>;
+	qcom,num-strings = <3>;
 };
 
 &rpm_requests {
@@ -938,10 +939,6 @@
 	};
 };
 
-/*
- * For reasons that are currently unknown (but probably related to fusb301), USB takes about
- * 6 minutes to wake up (nothing interesting in kernel logs), but then it works as it should.
- */
 &usb3 {
 	status = "okay";
 	qcom,select-utmi-as-pipe-clk;
@@ -950,6 +947,7 @@
 &usb3_dwc3 {
 	extcon = <&usb3_id>;
 	dr_mode = "peripheral";
+	maximum-speed = "high-speed";
 	phys = <&hsusb_phy1>;
 	phy-names = "usb2-phy";
 	snps,hird-threshold = /bits/ 8 <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -142,82 +142,92 @@
 		/* Nominal fmax for now */
 		opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-422400000 {
 			opp-hz = /bits/ 64 <422400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-480000000 {
 			opp-hz = /bits/ 64 <480000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-556800000 {
 			opp-hz = /bits/ 64 <556800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-652800000 {
 			opp-hz = /bits/ 64 <652800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-729600000 {
 			opp-hz = /bits/ 64 <729600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-844800000 {
 			opp-hz = /bits/ 64 <844800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-960000000 {
 			opp-hz = /bits/ 64 <960000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1036800000 {
 			opp-hz = /bits/ 64 <1036800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1113600000 {
 			opp-hz = /bits/ 64 <1113600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1190400000 {
 			opp-hz = /bits/ 64 <1190400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1228800000 {
 			opp-hz = /bits/ 64 <1228800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1324800000 {
 			opp-hz = /bits/ 64 <1324800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-supported-hw = <0x2>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x5>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1478400000 {
 			opp-hz = /bits/ 64 <1478400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			opp-supported-hw = <0x04>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1593600000 {
 			opp-hz = /bits/ 64 <1593600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -230,127 +240,137 @@
 		/* Nominal fmax for now */
 		opp-307200000 {
 			opp-hz = /bits/ 64 <307200000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-403200000 {
 			opp-hz = /bits/ 64 <403200000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-480000000 {
 			opp-hz = /bits/ 64 <480000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-556800000 {
 			opp-hz = /bits/ 64 <556800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-652800000 {
 			opp-hz = /bits/ 64 <652800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-729600000 {
 			opp-hz = /bits/ 64 <729600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-806400000 {
 			opp-hz = /bits/ 64 <806400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-883200000 {
 			opp-hz = /bits/ 64 <883200000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-940800000 {
 			opp-hz = /bits/ 64 <940800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1036800000 {
 			opp-hz = /bits/ 64 <1036800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1113600000 {
 			opp-hz = /bits/ 64 <1113600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1190400000 {
 			opp-hz = /bits/ 64 <1190400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1248000000 {
 			opp-hz = /bits/ 64 <1248000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1324800000 {
 			opp-hz = /bits/ 64 <1324800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1478400000 {
 			opp-hz = /bits/ 64 <1478400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1555200000 {
 			opp-hz = /bits/ 64 <1555200000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1632000000 {
 			opp-hz = /bits/ 64 <1632000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1708800000 {
 			opp-hz = /bits/ 64 <1708800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1785600000 {
 			opp-hz = /bits/ 64 <1785600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-supported-hw = <0x6>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1824000000 {
 			opp-hz = /bits/ 64 <1824000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-supported-hw = <0x4>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1920000000 {
 			opp-hz = /bits/ 64 <1920000000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 		opp-1996800000 {
 			opp-hz = /bits/ 64 <1996800000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 		opp-2073600000 {
 			opp-hz = /bits/ 64 <2073600000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 		opp-2150400000 {
 			opp-hz = /bits/ 64 <2150400000>;
-			opp-supported-hw = <0x77>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -374,6 +394,19 @@
 		reg = <0x0 0x80000000 0x0 0x0>;
 	};
 
+	etm {
+		compatible = "qcom,coresight-remote-etm";
+
+		out-ports {
+			port {
+				modem_etm_out_funnel_in2: endpoint {
+					remote-endpoint =
+					  <&funnel_in2_in_modem_etm>;
+				};
+			};
+		};
+	};
+
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
@@ -582,7 +615,6 @@
 		pcie_phy: phy@34000 {
 			compatible = "qcom,msm8996-qmp-pcie-phy";
 			reg = <0x00034000 0x488>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -598,12 +630,13 @@
 			reset-names = "phy", "common", "cfg";
 			status = "disabled";
 
-			pciephy_0: lane@35000 {
+			pciephy_0: phy@35000 {
 				reg = <0x00035000 0x130>,
 				      <0x00035200 0x200>,
 				      <0x00035400 0x1dc>;
 				#phy-cells = <0>;
 
+				#clock-cells = <0>;
 				clock-output-names = "pcie_0_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -611,12 +644,13 @@
 				reset-names = "lane0";
 			};
 
-			pciephy_1: lane@36000 {
+			pciephy_1: phy@36000 {
 				reg = <0x00036000 0x130>,
 				      <0x00036200 0x200>,
 				      <0x00036400 0x1dc>;
 				#phy-cells = <0>;
 
+				#clock-cells = <0>;
 				clock-output-names = "pcie_1_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
 				clock-names = "pipe1";
@@ -624,12 +658,13 @@
 				reset-names = "lane1";
 			};
 
-			pciephy_2: lane@37000 {
+			pciephy_2: phy@37000 {
 				reg = <0x00037000 0x130>,
 				      <0x00037200 0x200>,
 				      <0x00037400 0x1dc>;
 				#phy-cells = <0>;
 
+				#clock-cells = <0>;
 				clock-output-names = "pcie_2_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
 				clock-names = "pipe2";
@@ -638,7 +673,7 @@
 			};
 		};
 
-		rpm_msg_ram: memory@68000 {
+		rpm_msg_ram: sram@68000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00068000 0x6000>;
 		};
@@ -965,9 +1000,6 @@
 			nvmem-cells = <&speedbin_efuse>;
 			nvmem-cell-names = "speed_bin";
 
-			qcom,gpu-quirk-two-pass-use-wfi;
-			qcom,gpu-quirk-fault-detect-mask;
-
 			operating-points-v2 = <&gpu_opp_table>;
 
 			status = "disabled";
@@ -978,17 +1010,17 @@
 				compatible  ="operating-points-v2";
 
 				/*
-				 * 624Mhz and 560Mhz are only available on speed
-				 * bin (1 << 0). All the rest are available on
-				 * all bins of the hardware
+				 * 624Mhz is only available on speed bins 0 and 3.
+				 * 560Mhz is only available on speed bins 0, 2 and 3.
+				 * All the rest are available on all bins of the hardware.
 				 */
 				opp-624000000 {
 					opp-hz = /bits/ 64 <624000000>;
-					opp-supported-hw = <0x01>;
+					opp-supported-hw = <0x09>;
 				};
 				opp-560000000 {
 					opp-hz = /bits/ 64 <560000000>;
-					opp-supported-hw = <0x01>;
+					opp-supported-hw = <0x0d>;
 				};
 				opp-510000000 {
 					opp-hz = /bits/ 64 <510000000>;
@@ -1211,6 +1243,20 @@
 				};
 			};
 
+			blsp1_uart2_default: blsp1-uart2-default {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "blsp_uart2";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			blsp1_uart2_sleep: blsp1-uart2-sleep {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			blsp1_i2c3_default: blsp1-i2c2-default {
 				pins = "gpio47", "gpio48";
 				function = "blsp_i2c3";
@@ -1538,8 +1584,8 @@
 
 				#address-cells = <3>;
 				#size-cells = <2>;
-				ranges = <0x01000000 0x0 0x0c200000 0x0c200000 0x0 0x100000>,
-					<0x02000000 0x0 0x0c300000 0x0c300000 0x0 0xd00000>;
+				ranges = <0x01000000 0x0 0x00000000 0x0c200000 0x0 0x100000>,
+					 <0x02000000 0x0 0x0c300000 0x0c300000 0x0 0xd00000>;
 
 				device_type = "pci";
 
@@ -1592,8 +1638,8 @@
 
 				#address-cells = <3>;
 				#size-cells = <2>;
-				ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>,
-					<0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
+				ranges = <0x01000000 0x0 0x00000000 0x0d200000 0x0 0x100000>,
+					 <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
 
 				device_type = "pci";
 
@@ -1643,8 +1689,8 @@
 
 				#address-cells = <3>;
 				#size-cells = <2>;
-				ranges = <0x01000000 0x0 0x0e200000 0x0e200000 0x0 0x100000>,
-					<0x02000000 0x0 0x0e300000 0x0e300000 0x0 0x1d00000>;
+				ranges = <0x01000000 0x0 0x00000000 0x0e200000 0x0 0x100000>,
+					 <0x02000000 0x0 0x0e300000 0x0e300000 0x0 0x1d00000>;
 
 				device_type = "pci";
 
@@ -1712,7 +1758,7 @@
 				<&gcc GCC_UFS_RX_SYMBOL_0_CLK>;
 			freq-table-hz =
 				<100000000 200000000>,
-				<0 0>,
+				<100000000 200000000>,
 				<0 0>,
 				<0 0>,
 				<0 0>,
@@ -1746,7 +1792,7 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufsphy_lane: lanes@627400 {
+			ufsphy_lane: phy@627400 {
 				reg = <0x627400 0x12c>,
 				      <0x627600 0x200>,
 				      <0x627c00 0x1b4>;
@@ -1754,7 +1800,7 @@
 			};
 		};
 
-		camss: camss@a00000 {
+		camss: camss@a34000 {
 			compatible = "qcom,msm8996-camss";
 			reg = <0x00a34000 0x1000>,
 			      <0x00a00030 0x4>,
@@ -2172,6 +2218,14 @@
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
 
+			in-ports {
+				port {
+					funnel_in2_in_modem_etm: endpoint {
+						remote-endpoint =
+						  <&modem_etm_out_funnel_in2>;
+					};
+				};
+			};
 
 			out-ports {
 				port {
@@ -2554,9 +2608,14 @@
 			#size-cells = <1>;
 			ranges;
 
-			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "ss_phy_irq";
+			interrupt-names = "pwr_event",
+					  "qusb2_phy",
+					  "hs_phy_irq",
+					  "ss_phy_irq";
 
 			clocks = <&gcc GCC_SYS_NOC_USB3_AXI_CLK>,
 				<&gcc GCC_USB30_MASTER_CLK>,
@@ -2578,15 +2637,18 @@
 				interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&hsusb_phy1>, <&ssusb_phy_0>;
 				phy-names = "usb2-phy", "usb3-phy";
+				snps,hird-threshold = /bits/ 8 <0>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
+				snps,is-utmi-l1-suspend;
+				snps,parkmode-disable-ss-quirk;
+				tx-fifo-resize;
 			};
 		};
 
 		usb3phy: phy@7410000 {
 			compatible = "qcom,msm8996-qmp-usb3-phy";
 			reg = <0x07410000 0x1c4>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -2601,12 +2663,13 @@
 			reset-names = "phy", "common";
 			status = "disabled";
 
-			ssusb_phy_0: lane@7410200 {
+			ssusb_phy_0: phy@7410200 {
 				reg = <0x07410200 0x200>,
 				      <0x07410400 0x130>,
 				      <0x07410600 0x1a8>;
 				#phy-cells = <0>;
 
+				#clock-cells = <0>;
 				clock-output-names = "usb3_phy_pipe_clk_src";
 				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -2704,6 +2767,9 @@
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
 			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
 			dma-names = "tx", "rx";
 			status = "disabled";
@@ -2865,6 +2931,9 @@
 			#size-cells = <1>;
 			ranges;
 
+			interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq";
+
 			clocks = <&gcc GCC_PERIPH_NOC_USB20_AHB_CLK>,
 				<&gcc GCC_USB20_MASTER_CLK>,
 				<&gcc GCC_USB20_MOCK_UTMI_CLK>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8996pro.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8996pro.dtsi
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include "msm8996.dtsi"
+
+/ {
+	/delete-node/ opp-table-cluster0;
+	/delete-node/ opp-table-cluster1;
+
+	/*
+	 * On MSM8996 Pro the cpufreq driver shifts speed bins into the high
+	 * nibble of supported hw, so speed bin 0 becomes 0x10, speed bin 1
+	 * becomes 0x20, speed 2 becomes 0x40.
+	 */
+
+	cluster0_opp: opp-table-cluster0 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-768000000 {
+			opp-hz = /bits/ 64 <768000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-844800000 {
+			opp-hz = /bits/ 64 <844800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			opp-supported-hw = <0x20>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2188800000 {
+			opp-hz = /bits/ 64 <2188800000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
+	cluster1_opp: opp-table-cluster1 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-748800000 {
+			opp-hz = /bits/ 64 <748800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1824000000 {
+			opp-hz = /bits/ 64 <1824000000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2150400000 {
+			opp-hz = /bits/ 64 <2150400000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2342400000 {
+			opp-hz = /bits/ 64 <2342400000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -308,38 +308,42 @@
 			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
 				compatible = "arm,idle-state";
 				idle-state-name = "little-retention";
+				/* CPU Retention (C2D), L2 Active */
 				arm,psci-suspend-param = <0x00000002>;
 				entry-latency-us = <81>;
 				exit-latency-us = <86>;
-				min-residency-us = <200>;
+				min-residency-us = <504>;
 			};
 
 			LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
 				compatible = "arm,idle-state";
 				idle-state-name = "little-power-collapse";
+				/* CPU + L2 Power Collapse (C3, D4) */
 				arm,psci-suspend-param = <0x40000003>;
-				entry-latency-us = <273>;
-				exit-latency-us = <612>;
-				min-residency-us = <1000>;
+				entry-latency-us = <814>;
+				exit-latency-us = <4562>;
+				min-residency-us = <9183>;
 				local-timer-stop;
 			};
 
 			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
 				compatible = "arm,idle-state";
 				idle-state-name = "big-retention";
+				/* CPU Retention (C2D), L2 Active */
 				arm,psci-suspend-param = <0x00000002>;
 				entry-latency-us = <79>;
 				exit-latency-us = <82>;
-				min-residency-us = <200>;
+				min-residency-us = <1302>;
 			};
 
 			BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
 				compatible = "arm,idle-state";
 				idle-state-name = "big-power-collapse";
+				/* CPU + L2 Power Collapse (C3, D4) */
 				arm,psci-suspend-param = <0x40000003>;
-				entry-latency-us = <336>;
-				exit-latency-us = <525>;
-				min-residency-us = <1000>;
+				entry-latency-us = <724>;
+				exit-latency-us = <2027>;
+				min-residency-us = <9419>;
 				local-timer-stop;
 			};
 		};
@@ -857,7 +861,7 @@
 			reg = <0x00100000 0xb0000>;
 		};
 
-		rpm_msg_ram: memory@778000 {
+		rpm_msg_ram: sram@778000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00778000 0x7000>;
 		};
@@ -947,17 +951,17 @@
 			phy-names = "pciephy";
 			status = "disabled";
 
-			ranges = <0x01000000 0x0 0x1b200000 0x1b200000 0x0 0x100000>,
+			ranges = <0x01000000 0x0 0x00000000 0x1b200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x1b300000 0x1b300000 0x0 0xd00000>;
 
 			#interrupt-cells = <1>;
 			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map =	<0 0 0 1 &intc 0 135 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 2 &intc 0 136 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 3 &intc 0 138 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 4 &intc 0 139 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map =	<0 0 0 1 &intc 0 0 135 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 136 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 138 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 139 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
 				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
@@ -990,7 +994,7 @@
 			vdda-phy-supply = <&vreg_l1a_0p875>;
 			vdda-pll-supply = <&vreg_l2a_1p2>;
 
-			pciephy: lane@1c06800 {
+			pciephy: phy@1c06800 {
 				reg = <0x01c06200 0x128>, <0x01c06400 0x1fc>, <0x01c06800 0x20c>;
 				#phy-cells = <0>;
 
@@ -1062,7 +1066,7 @@
 			reset-names = "ufsphy";
 			resets = <&ufshc 0>;
 
-			ufsphy_lanes: lanes@1da7400 {
+			ufsphy_lanes: phy@1da7400 {
 				reg = <0x01da7400 0x128>,
 				      <0x01da7600 0x1fc>,
 				      <0x01da7c00 0x1dc>,
@@ -1469,7 +1473,7 @@
 			compatible = "arm,coresight-stm", "arm,primecell";
 			reg = <0x06002000 0x1000>,
 			      <0x16280000 0x180000>;
-			reg-names = "stm-base", "stm-data-base";
+			reg-names = "stm-base", "stm-stimulus-base";
 			status = "disabled";
 
 			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
@@ -1859,9 +1863,11 @@
 
 			cpu = <&CPU4>;
 
-			port{
-				etm4_out: endpoint {
-					remote-endpoint = <&apss_funnel_in4>;
+			out-ports {
+				port{
+					etm4_out: endpoint {
+						remote-endpoint = <&apss_funnel_in4>;
+					};
 				};
 			};
 		};
@@ -1876,9 +1882,11 @@
 
 			cpu = <&CPU5>;
 
-			port{
-				etm5_out: endpoint {
-					remote-endpoint = <&apss_funnel_in5>;
+			out-ports {
+				port{
+					etm5_out: endpoint {
+						remote-endpoint = <&apss_funnel_in5>;
+					};
 				};
 			};
 		};
@@ -1893,9 +1901,11 @@
 
 			cpu = <&CPU6>;
 
-			port{
-				etm6_out: endpoint {
-					remote-endpoint = <&apss_funnel_in6>;
+			out-ports {
+				port{
+					etm6_out: endpoint {
+						remote-endpoint = <&apss_funnel_in6>;
+					};
 				};
 			};
 		};
@@ -1910,9 +1920,11 @@
 
 			cpu = <&CPU7>;
 
-			port{
-				etm7_out: endpoint {
-					remote-endpoint = <&apss_funnel_in7>;
+			out-ports {
+				port{
+					etm7_out: endpoint {
+						remote-endpoint = <&apss_funnel_in7>;
+					};
 				};
 			};
 		};
@@ -1970,7 +1982,8 @@
 				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
-				phys = <&qusb2phy>, <&usb1_ssphy>;
+				snps,parkmode-disable-ss-quirk;
+				phys = <&qusb2phy>, <&usb3phy>;
 				phy-names = "usb2-phy", "usb3-phy";
 				snps,has-lpm-erratum;
 				snps,hird-threshold = /bits/ 8 <0x10>;
@@ -1979,33 +1992,26 @@
 
 		usb3phy: phy@c010000 {
 			compatible = "qcom,msm8998-qmp-usb3-phy";
-			reg = <0x0c010000 0x18c>;
-			status = "disabled";
-			#clock-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
+			reg = <0x0c010000 0x1000>;
 
 			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB3_CLKREF_CLK>,
 				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
-				 <&gcc GCC_USB3_CLKREF_CLK>;
-			clock-names = "aux", "cfg_ahb", "ref";
+				 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "cfg_ahb",
+				      "pipe";
+			clock-output-names = "usb3_phy_pipe_clk_src";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
 
 			resets = <&gcc GCC_USB3_PHY_BCR>,
 				 <&gcc GCC_USB3PHY_PHY_BCR>;
-			reset-names = "phy", "common";
+			reset-names = "phy",
+				      "phy_phy";
 
-			usb1_ssphy: lane@c010200 {
-				reg = <0xc010200 0x128>,
-				      <0xc010400 0x200>,
-				      <0xc010c00 0x20c>,
-				      <0xc010600 0x128>,
-				      <0xc010800 0x200>;
-				#phy-cells = <0>;
-				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb3_phy_pipe_clk_src";
-			};
+			status = "disabled";
 		};
 
 		qusb2phy: phy@c012000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/pm660.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/pm660.dtsi
@@ -152,7 +152,7 @@
 				qcom,pre-scaling = <1 3>;
 			};
 
-			vcoin: vcoin@83 {
+			vcoin: vcoin@85 {
 				reg = <ADC5_VCOIN>;
 				qcom,decimation = <1024>;
 				qcom,pre-scaling = <1 3>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/pm660l.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/pm660l.dtsi
@@ -67,9 +67,10 @@
 
 		pm660l_wled: leds@d800 {
 			compatible = "qcom,pm660l-wled";
-			reg = <0xd800 0xd900>;
-			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "ovp";
+			reg = <0xd800>, <0xd900>;
+			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
+				     <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ovp", "short";
 			label = "backlight";
 
 			qcom,switching-freq = <800>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/pm8916.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/pm8916.dtsi
@@ -86,7 +86,6 @@
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>;
-			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/pmi8994.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/pmi8994.dtsi
@@ -35,14 +35,12 @@
 
 		pmi8994_wled: wled@d800 {
 			compatible = "qcom,pmi8994-wled";
-			reg = <0xd800 0xd900>;
-			interrupts = <3 0xd8 0x02 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "short";
-			qcom,num-strings = <3>;
-			/* Yes, all four strings *have to* be defined or things won't work. */
-			qcom,enabled-strings = <0 1 2 3>;
+			reg = <0xd800>, <0xd900>;
+			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
+				     <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ovp", "short";
 			qcom,cabc;
-			qcom,eternal-pfet;
+			qcom,external-pfet;
 			status = "disabled";
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/pmi8998.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/pmi8998.dtsi
@@ -41,5 +41,17 @@
 				interrupt-names = "sc-err", "ocp";
 			};
 		};
+
+		pmi8998_wled: leds@d800 {
+			compatible = "qcom,pmi8998-wled";
+			reg = <0xd800>, <0xd900>;
+			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
+				     <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ovp", "short";
+			label = "backlight";
+
+			status = "disabled";
+		};
+
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/pmk8350.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/pmk8350.dtsi
@@ -16,8 +16,9 @@
 		#size-cells = <0>;
 
 		pmk8350_pon: pon@1300 {
-			compatible = "qcom,pm8998-pon";
-			reg = <0x1300>;
+			compatible = "qcom,pmk8350-pon";
+			reg = <0x1300>, <0x800>;
+			reg-names = "hlos", "pbs";
 
 			pwrkey {
 				compatible = "qcom,pmk8350-pwrkey";
@@ -44,7 +45,7 @@
 		};
 
 		pmk8350_adc_tm: adc-tm@3400 {
-			compatible = "qcom,adc-tm7";
+			compatible = "qcom,spmi-adc-tm5-gen2";
 			reg = <0x3400>;
 			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "threshold";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -60,7 +60,7 @@
 		vddrf-supply = <&vreg_l1_1p3>;
 		vddch0-supply = <&vdd_ch0_3p3>;
 
-		local-bd-address = [ 02 00 00 00 5a ad ];
+		local-bd-address = [ 00 00 00 00 00 00 ];
 
 		max-speed = <3200000>;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -318,7 +318,7 @@
 			status = "disabled";
 		};
 
-		rpm_msg_ram: memory@60000 {
+		rpm_msg_ram: sram@60000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00060000 0x6000>;
 		};
@@ -548,7 +548,7 @@
 				compatible = "snps,dwc3";
 				reg = <0x07580000 0xcd00>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&usb2_phy_sec>, <&usb3_phy>;
+				phys = <&usb2_phy_prim>, <&usb3_phy>;
 				phy-names = "usb2-phy", "usb3-phy";
 				snps,has-lpm-erratum;
 				snps,hird-threshold = /bits/ 8 <0x10>;
@@ -577,7 +577,7 @@
 				compatible = "snps,dwc3";
 				reg = <0x078c0000 0xcc00>;
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&usb2_phy_prim>;
+				phys = <&usb2_phy_sec>;
 				phy-names = "usb2-phy";
 				snps,has-lpm-erratum;
 				snps,hird-threshold = /bits/ 8 <0x10>;
@@ -775,7 +775,7 @@
 
 			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
 			resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
-				 <&gcc 21>;
+				 <&gcc GCC_PCIE_0_PIPE_ARES>;
 			reset-names = "phy", "pipe";
 
 			clock-output-names = "pcie_0_pipe_clk";
@@ -1305,12 +1305,12 @@
 				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
 			clock-names = "iface", "aux", "master_bus", "slave_bus";
 
-			resets = <&gcc 18>,
-				 <&gcc 17>,
-				 <&gcc 15>,
-				 <&gcc 19>,
+			resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
+				 <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
+				 <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
+				 <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
 				 <&gcc GCC_PCIE_0_BCR>,
-				 <&gcc 16>;
+				 <&gcc GCC_PCIE_0_AHB_ARES>;
 			reset-names = "axi_m",
 				      "axi_s",
 				      "axi_m_sticky",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -27,7 +27,7 @@
 	};
 
 	/* Fixed crystal oscillator dedicated to MCP2518FD */
-	clk40M: can_clock {
+	clk40M: can-clock {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <40000000>;
@@ -58,8 +58,8 @@
 		user4 {
 			label = "green:user4";
 			gpios = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "panic-indicator";
 			default-state = "off";
+			panic-indicator;
 		};
 
 		wlan {
@@ -113,7 +113,7 @@
 			};
 		};
 
-		pm8150l-thermal {
+		pm8150l-pcb-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&pm8150l_adc_tm 1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -43,7 +43,6 @@
 
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-allow-set-load;
 
 		vin-supply = <&vreg_3p3>;
 	};
@@ -114,6 +113,9 @@
 			regulator-max-microvolt = <880000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7a_1p8: ldo7 {
@@ -129,6 +131,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l11a_0p8: ldo11 {
@@ -235,6 +240,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_1p8: ldo7 {
@@ -250,6 +258,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7180-lite.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7180-lite.dtsi
@@ -16,3 +16,11 @@
 &cpu6_opp12 {
 	opp-peak-kBps = <8532000 23347200>;
 };
+
+&cpu6_opp13 {
+	opp-peak-kBps = <8532000 23347200>;
+};
+
+&cpu6_opp14 {
+	opp-peak-kBps = <8532000 23347200>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
@@ -33,7 +33,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&pm6150_adc_tm 1>;
-			sustainable-power = <814>;
+			sustainable-power = <965>;
 
 			trips {
 				skin_temp_alert0: trip-point0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts
@@ -26,7 +26,7 @@
 		interrupt-parent = <&tlmm>;
 		interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
 
-		vcc-supply = <&pp3300_fp_tp>;
+		vdd-supply = <&pp3300_fp_tp>;
 		hid-descr-addr = <0x20>;
 
 		wakeup-source;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
@@ -44,7 +44,7 @@
 };
 
 &cpu6_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &cpu7_alert0 {
@@ -56,7 +56,7 @@
 };
 
 &cpu7_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &cpu8_alert0 {
@@ -68,7 +68,7 @@
 };
 
 &cpu8_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &cpu9_alert0 {
@@ -80,7 +80,7 @@
 };
 
 &cpu9_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &gpio_keys {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
@@ -42,6 +42,7 @@
  */
 
 /delete-node/ &hyp_mem;
+/delete-node/ &ipa_fw_mem;
 /delete-node/ &xbl_mem;
 /delete-node/ &aop_mem;
 /delete-node/ &sec_apps_mem;
@@ -910,6 +911,8 @@
 		vddrf-supply = <&pp1300_l2c>;
 		vddch0-supply = <&pp3300_l10c>;
 		max-speed = <3200000>;
+
+		qcom,local-bd-address-broken;
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -137,8 +137,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
@@ -162,8 +162,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_100>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -184,8 +184,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_200>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -206,8 +206,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_300>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -228,8 +228,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_400>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -250,8 +250,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_500>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -272,8 +272,8 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1740>;
-			dynamic-power-coefficient = <405>;
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <480>;
 			next-level-cache = <&L2_600>;
 			operating-points-v2 = <&cpu6_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -294,8 +294,8 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1740>;
-			dynamic-power-coefficient = <405>;
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <480>;
 			next-level-cache = <&L2_700>;
 			operating-points-v2 = <&cpu6_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -1460,6 +1460,8 @@
 					     "imem",
 					     "config";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&ipa_smp2p_out 0>,
 					   <&ipa_smp2p_out 1>;
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
@@ -2772,8 +2774,8 @@
 
 			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 8 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 9 IRQ_TYPE_LEVEL_HIGH>;
+					      <&pdc 8 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 9 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -3239,8 +3241,8 @@
 			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
 			interrupt-controller;
 			#interrupt-cells = <4>;
 			cell-index = <0>;
@@ -3364,7 +3366,7 @@
 			compatible = "qcom,apss-wdt-sc7180", "qcom,kpss-wdt";
 			reg = <0 0x17c10000 0 0x1000>;
 			clocks = <&sleep_clk>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		timer@17c20000{
@@ -3616,7 +3618,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 1>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu0_alert0: trip-point0 {
@@ -3665,7 +3667,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 2>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu1_alert0: trip-point0 {
@@ -3714,7 +3716,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 3>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu2_alert0: trip-point0 {
@@ -3763,7 +3765,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 4>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu3_alert0: trip-point0 {
@@ -3812,7 +3814,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 5>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu4_alert0: trip-point0 {
@@ -3861,7 +3863,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 6>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu5_alert0: trip-point0 {
@@ -3910,7 +3912,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 9>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu6_alert0: trip-point0 {
@@ -3951,7 +3953,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 10>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu7_alert0: trip-point0 {
@@ -3992,7 +3994,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 11>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu8_alert0: trip-point0 {
@@ -4033,7 +4035,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 12>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu9_alert0: trip-point0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -39,7 +39,7 @@
 
 		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32000>;
+			clock-frequency = <32764>;
 			#clock-cells = <0>;
 		};
 	};
@@ -429,7 +429,7 @@
 				 <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>,
 				 <0>, <0>, <0>, <0>, <0>, <0>;
 			clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk",
-				      "pcie_0_pipe_clk", "pcie_1_pipe-clk",
+				      "pcie_0_pipe_clk", "pcie_1_pipe_clk",
 				      "ufs_phy_rx_symbol_0_clk", "ufs_phy_rx_symbol_1_clk",
 				      "ufs_phy_tx_symbol_0_clk",
 				      "usb3_phy_wrapper_gcc_usb30_pipe_clk";
@@ -485,6 +485,7 @@
 
 			bus-width = <8>;
 			supports-cqe;
+			dma-coherent;
 
 			qcom,dll-config = <0x0007642c>;
 			qcom,ddr-config = <0x80040868>;
@@ -615,6 +616,8 @@
 			interconnect-names = "memory",
 					     "config";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&ipa_smp2p_out 0>,
 					   <&ipa_smp2p_out 1>;
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
@@ -1172,6 +1175,7 @@
 			operating-points-v2 = <&sdhc2_opp_table>;
 
 			bus-width = <4>;
+			dma-coherent;
 
 			qcom,dll-config = <0x0007642c>;
 
@@ -1258,15 +1262,11 @@
 			dp_phy: dp-phy@88ea200 {
 				reg = <0 0x088ea200 0 0x200>,
 				      <0 0x088ea400 0 0x200>,
-				      <0 0x088eac00 0 0x400>,
+				      <0 0x088eaa00 0 0x200>,
 				      <0 0x088ea600 0 0x200>,
-				      <0 0x088ea800 0 0x200>,
-				      <0 0x088eaa00 0 0x100>;
+				      <0 0x088ea800 0 0x200>;
 				#phy-cells = <0>;
 				#clock-cells = <1>;
-				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb3_phy_pipe_clk_src";
 			};
 		};
 
@@ -1292,8 +1292,8 @@
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
-				     <&pdc 13 IRQ_TYPE_EDGE_RISING>,
-				     <&pdc 12 IRQ_TYPE_EDGE_RISING>;
+					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -1496,8 +1496,8 @@
 			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
 			interrupt-controller;
 			#interrupt-cells = <4>;
 		};
@@ -1713,7 +1713,7 @@
 			compatible = "qcom,apss-wdt-sc7280", "qcom,kpss-wdt";
 			reg = <0 0x17c10000 0 0x1000>;
 			clocks = <&sleep_clk>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		timer@17c20000 {
@@ -1853,6 +1853,14 @@
 			reg = <0 0x18591000 0 0x1000>,
 			      <0 0x18592000 0 0x1000>,
 			      <0 0x18593000 0 0x1000>;
+
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dcvsh-irq-0",
+					  "dcvsh-irq-1",
+					  "dcvsh-irq-2";
+
 			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
 			clock-names = "xo", "alternate";
 			#freq-domain-cells = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/clock/qcom,gpucc-sdm660.h>
 #include <dt-bindings/clock/qcom,mmcc-sdm660.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interconnect/qcom,sdm660.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -541,7 +542,7 @@
 					<&sleep_clk>;
 		};
 
-		rpm_msg_ram: memory@778000 {
+		rpm_msg_ram: sram@778000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00778000 0x7000>;
 		};
@@ -767,7 +768,7 @@
 					pins = "gpio17", "gpio18", "gpio19";
 					function = "gpio";
 					drive-strength = <2>;
-					bias-no-pull;
+					bias-disable;
 				};
 			};
 
@@ -1041,11 +1042,13 @@
 			nvmem-cells = <&gpu_speed_bin>;
 			nvmem-cell-names = "speed_bin";
 
-			interconnects = <&gnoc 1 &bimc 5>;
+			interconnects = <&bimc MASTER_OXILI &bimc SLAVE_EBI>;
 			interconnect-names = "gfx-mem";
 
 			operating-points-v2 = <&gpu_sdm630_opp_table>;
 
+			status = "disabled";
+
 			gpu_sdm630_opp_table: opp-table {
 				compatible  = "operating-points-v2";
 				opp-775000000 {
@@ -1233,6 +1236,7 @@
 				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
+				snps,parkmode-disable-ss-quirk;
 
 				/*
 				 * SDM630 technically supports USB3 but I
@@ -1251,7 +1255,7 @@
 			#phy-cells = <0>;
 
 			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
-				<&gcc GCC_RX1_USB2_CLKREF_CLK>;
+				 <&gcc GCC_RX0_USB2_CLKREF_CLK>;
 			clock-names = "cfg_ahb", "ref";
 
 			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
@@ -1831,7 +1835,7 @@
 			};
 		};
 
-		camss: camss@ca00000 {
+		camss: camss@ca00020 {
 			compatible = "qcom,sdm660-camss";
 			reg = <0x0c824000 0x1000>,
 			      <0x0ca00120 0x4>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts
@@ -18,7 +18,7 @@
 };
 
 &sdc2_state_on {
-	pinconf-clk {
+	clk {
 		drive-strength = <14>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
@@ -1299,7 +1299,7 @@
 		config {
 			pins = "gpio126";
 			function = "gpio";
-			bias-no-pull;
+			bias-disable;
 			drive-strength = <2>;
 			output-low;
 		};
@@ -1309,7 +1309,7 @@
 		config {
 			pins = "gpio126";
 			function = "gpio";
-			bias-no-pull;
+			bias-disable;
 			drive-strength = <2>;
 			output-high;
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -55,8 +55,8 @@
 		user4 {
 			label = "green:user4";
 			gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "panic-indicator";
 			default-state = "off";
+			panic-indicator;
 		};
 
 		wlan {
@@ -896,7 +896,7 @@
 	};
 
 	wcd_intr_default: wcd_intr_default {
-		pins = <54>;
+		pins = "gpio54";
 		function = "gpio";
 
 		input-enable;
@@ -1045,7 +1045,10 @@
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 &qup_spi2_default {
-	drive-strength = <16>;
+	pinconf {
+		pins = "gpio27", "gpio28", "gpio29", "gpio30";
+		drive-strength = <16>;
+	};
 };
 
 &qup_uart3_default{
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -572,6 +572,8 @@
 	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
 };
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -221,7 +221,7 @@
 	panel@0 {
 		compatible = "tianma,fhd-video";
 		reg = <0>;
-		vddi0-supply = <&vreg_l14a_1p8>;
+		vddio-supply = <&vreg_l14a_1p8>;
 		vddpos-supply = <&lab>;
 		vddneg-supply = <&ibb>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -196,8 +196,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <154>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -221,8 +221,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <154>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -243,8 +243,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <154>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -265,8 +265,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <154>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -288,7 +288,7 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -310,7 +310,7 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -332,7 +332,7 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -354,7 +354,7 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
@@ -1074,6 +1074,7 @@
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
+			power-domains = <&rpmhpd SDM845_CX>;
 		};
 
 		qfprom@784000 {
@@ -1988,17 +1989,17 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
-				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0xd00000>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0xd00000>;
 
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
 				 <&gcc GCC_PCIE_0_AUX_CLK>,
@@ -2064,7 +2065,7 @@
 
 			status = "disabled";
 
-			pcie0_lane: lanes@1c06200 {
+			pcie0_lane: phy@1c06200 {
 				reg = <0 0x01c06200 0 0x128>,
 				      <0 0x01c06400 0 0x1fc>,
 				      <0 0x01c06800 0 0x218>,
@@ -2093,17 +2094,17 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
 
 			interrupts = <GIC_SPI 307 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
 				 <&gcc GCC_PCIE_1_AUX_CLK>,
@@ -2174,7 +2175,7 @@
 
 			status = "disabled";
 
-			pcie1_lane: lanes@1c06200 {
+			pcie1_lane: phy@1c06200 {
 				reg = <0 0x01c0a800 0 0x800>,
 				      <0 0x01c0a800 0 0x800>,
 				      <0 0x01c0b800 0 0x400>;
@@ -2282,7 +2283,7 @@
 				<0 0>,
 				<0 0>,
 				<0 0>,
-				<0 300000000>;
+				<75000000 300000000>;
 
 			status = "disabled";
 		};
@@ -2298,11 +2299,13 @@
 			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
 				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
 
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
 			resets = <&ufs_mem_hc 0>;
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
+			ufs_mem_phy_lanes: phy@1d87400 {
 				reg = <0 0x01d87400 0 0x108>,
 				      <0 0x01d87600 0 0x1e0>,
 				      <0 0x01d87c00 0 0x1dc>,
@@ -2316,11 +2319,11 @@
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0 0x01dc4000 0 0x24000>;
 			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rpmhcc 15>;
+			clocks = <&rpmhcc RPMH_CE_CLK>;
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			iommus = <&apps_smmu 0x704 0x1>,
 				 <&apps_smmu 0x706 0x1>,
 				 <&apps_smmu 0x714 0x1>,
@@ -2331,8 +2334,8 @@
 			compatible = "qcom,crypto-v5.4";
 			reg = <0 0x01dfa000 0 0x6000>;
 			clocks = <&gcc GCC_CE1_AHB_CLK>,
-				 <&gcc GCC_CE1_AHB_CLK>,
-				 <&rpmhcc 15>;
+				 <&gcc GCC_CE1_AXI_CLK>,
+				 <&rpmhcc RPMH_CE_CLK>;
 			clock-names = "iface", "bus", "core";
 			dmas = <&cryptobam 6>, <&cryptobam 7>;
 			dma-names = "rx", "tx";
@@ -3608,10 +3611,10 @@
 					#clock-cells = <0>;
 					clock-frequency = <9600000>;
 					clock-output-names = "mclk";
-					qcom,micbias1-millivolt = <1800>;
-					qcom,micbias2-millivolt = <1800>;
-					qcom,micbias3-millivolt = <1800>;
-					qcom,micbias4-millivolt = <1800>;
+					qcom,micbias1-microvolt = <1800000>;
+					qcom,micbias2-microvolt = <1800000>;
+					qcom,micbias3-microvolt = <1800000>;
+					qcom,micbias4-microvolt = <1800000>;
 
 					#address-cells = <1>;
 					#size-cells = <1>;
@@ -3699,7 +3702,7 @@
 				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			usb_1_ssphy: lanes@88e9200 {
+			usb_1_ssphy: phy@88e9200 {
 				reg = <0 0x088e9200 0 0x128>,
 				      <0 0x088e9400 0 0x200>,
 				      <0 0x088e9c00 0 0x218>,
@@ -3732,7 +3735,7 @@
 				 <&gcc GCC_USB3_PHY_SEC_BCR>;
 			reset-names = "phy", "common";
 
-			usb_2_ssphy: lane@88eb200 {
+			usb_2_ssphy: phy@88eb200 {
 				reg = <0 0x088eb200 0 0x128>,
 				      <0 0x088eb400 0 0x1fc>,
 				      <0 0x088eb800 0 0x218>,
@@ -3766,10 +3769,10 @@
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <150000000>;
 
-			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc_intc 8 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc_intc 9 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -3814,10 +3817,10 @@
 					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <150000000>;
 
-			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc_intc 10 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc_intc 11 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -3921,7 +3924,7 @@
 			#reset-cells = <1>;
 		};
 
-		camss: camss@a00000 {
+		camss: camss@acb3000 {
 			compatible = "qcom,sdm845-camss";
 
 			reg = <0 0xacb3000 0 0x1000>,
@@ -3945,16 +3948,16 @@
 				"vfe1",
 				"vfe_lite";
 
-			interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 448 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "csid0",
 				"csid1",
 				"csid2",
@@ -4147,7 +4150,7 @@
 
 			power-domains = <&dispcc MDSS_GDSC>;
 
-			clocks = <&gcc GCC_DISP_AHB_CLK>,
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
 				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
 			clock-names = "iface", "core";
 
@@ -4724,7 +4727,7 @@
 			compatible = "qcom,apss-wdt-sdm845", "qcom,kpss-wdt";
 			reg = <0 0x17980000 0 0x1000>;
 			clocks = <&sleep_clk>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		apss_shared: mailbox@17990000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
@@ -475,8 +475,10 @@
 };
 
 &qup_i2c12_default {
-	drive-strength = <2>;
-	bias-disable;
+	pinmux {
+		drive-strength = <2>;
+		bias-disable;
+	};
 };
 
 &qup_uart6_default {
@@ -518,6 +520,10 @@
 	dai@1 {
 		reg = <1>;
 	};
+
+	dai@2 {
+		reg = <2>;
+	};
 };
 
 &sound {
@@ -530,6 +536,7 @@
 		"SpkrLeft IN", "SPK1 OUT",
 		"SpkrRight IN", "SPK2 OUT",
 		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL3",  "MultiMedia3 Playback",
 		"MultiMedia2 Capture", "MM_UL2";
 
 	mm1-dai-link {
@@ -546,6 +553,13 @@
 		};
 	};
 
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
 	slim-dai-link {
 		link-name = "SLIM Playback";
 		cpu {
@@ -575,6 +589,21 @@
 			sound-dai = <&wcd9340 1>;
 		};
 	};
+
+	slim-wcd-dai-link {
+		link-name = "SLIM WCD Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_1_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai =  <&wcd9340 2>;
+		};
+	};
 };
 
 &tlmm {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
@@ -74,7 +74,7 @@
 			reg = <0x0 0xffc40000 0x0 0xc0000>;
 			record-size = <0x1000>;
 			console-size = <0x40000>;
-			msg-size = <0x20000 0x20000>;
+			pmsg-size = <0x20000>;
 		};
 
 		cmdline_mem: memory@ffd00000 {
@@ -88,11 +88,19 @@
 	status = "okay";
 };
 
-&sdc2_state_off {
+&sdc2_off_state {
 	sd-cd {
 		pins = "gpio98";
+		drive-strength = <2>;
 		bias-disable;
+	};
+};
+
+&sdc2_on_state {
+	sd-cd {
+		pins = "gpio98";
 		drive-strength = <2>;
+		bias-pull-up;
 	};
 };
 
@@ -102,32 +110,6 @@
 
 &tlmm {
 	gpio-reserved-ranges = <22 2>, <28 6>;
-
-	sdc2_state_on: sdc2-on {
-		clk {
-			pins = "sdc2_clk";
-			bias-disable;
-			drive-strength = <16>;
-		};
-
-		cmd {
-			pins = "sdc2_cmd";
-			bias-pull-up;
-			drive-strength = <10>;
-		};
-
-		data {
-			pins = "sdc2_data";
-			bias-pull-up;
-			drive-strength = <10>;
-		};
-
-		sd-cd {
-			pins = "gpio98";
-			bias-pull-up;
-			drive-strength = <2>;
-		};
-	};
 };
 
 &usb3 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm6125.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm6125.dtsi
@@ -27,7 +27,7 @@
 		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <32000>;
+			clock-frequency = <32764>;
 			clock-output-names = "sleep_clk";
 		};
 	};
@@ -336,23 +336,43 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			sdc2_state_off: sdc2-off {
+			sdc2_off_state: sdc2-off-state {
 				clk {
 					pins = "sdc2_clk";
-					bias-disable;
 					drive-strength = <2>;
+					bias-disable;
 				};
 
 				cmd {
 					pins = "sdc2_cmd";
+					drive-strength = <2>;
 					bias-pull-up;
+				};
+
+				data {
+					pins = "sdc2_data";
 					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			sdc2_on_state: sdc2-on-state {
+				clk {
+					pins = "sdc2_clk";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cmd {
+					pins = "sdc2_cmd";
+					drive-strength = <10>;
+					bias-pull-up;
 				};
 
 				data {
 					pins = "sdc2_data";
+					drive-strength = <10>;
 					bias-pull-up;
-					drive-strength = <2>;
 				};
 			};
 		};
@@ -372,15 +392,15 @@
 			reg = <0x01613000 0x180>;
 			#phy-cells = <0>;
 
-			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
-				 <&gcc GCC_AHB2PHY_USB_CLK>;
-			clock-names = "ref", "cfg_ahb";
+			clocks = <&gcc GCC_AHB2PHY_USB_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "cfg_ahb", "ref";
 
 			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
 			status = "disabled";
 		};
 
-		rpm_msg_ram: memory@45f0000 {
+		rpm_msg_ram: sram@45f0000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x045f0000 0x7000>;
 		};
@@ -388,7 +408,7 @@
 		sdhc_1: sdhci@4744000 {
 			compatible = "qcom,sm6125-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x04744000 0x1000>, <0x04745000 0x1000>;
-			reg-names = "hc", "core";
+			reg-names = "hc", "cqhci";
 
 			interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
@@ -417,8 +437,8 @@
 				<&xo_board>;
 			clock-names = "iface", "core", "xo";
 
-			pinctrl-0 = <&sdc2_state_on>;
-			pinctrl-1 = <&sdc2_state_off>;
+			pinctrl-0 = <&sdc2_on_state>;
+			pinctrl-1 = <&sdc2_off_state>;
 			pinctrl-names = "default", "sleep";
 
 			bus-width = <4>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -126,8 +126,6 @@
 		vdda_sp_sensor:
 		vdda_ufs_2ln_core_1:
 		vdda_ufs_2ln_core_2:
-		vdda_usb_ss_dp_core_1:
-		vdda_usb_ss_dp_core_2:
 		vdda_qlink_lv:
 		vdda_qlink_lv_ck:
 		vreg_l5a_0p875: ldo5 {
@@ -209,6 +207,12 @@
 			regulator-max-microvolt = <3008000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
+
+		vreg_l18a_0p8: ldo18 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
 	};
 
 	pm8150l-rpmh-regulators {
@@ -441,13 +445,13 @@
 &usb_1_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+	vdda-pll-supply = <&vreg_l18a_0p8>;
 };
 
 &usb_2_qmpphy {
 	status = "okay";
 	vdda-phy-supply = <&vreg_l3c_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+	vdda-pll-supply = <&vreg_l5a_0p875>;
 };
 
 &usb_1 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
@@ -375,8 +375,8 @@
 		pinctrl-0 = <&da7280_intr_default>;
 
 		dlg,actuator-type = "LRA";
-		dlg,dlg,const-op-mode = <1>;
-		dlg,dlg,periodic-op-mode = <1>;
+		dlg,const-op-mode = <1>;
+		dlg,periodic-op-mode = <1>;
 		dlg,nom-microvolt = <2000000>;
 		dlg,abs-max-microvolt = <2000000>;
 		dlg,imax-microamp = <129000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
@@ -33,9 +33,10 @@
 		framebuffer: framebuffer@9c000000 {
 			compatible = "simple-framebuffer";
 			reg = <0 0x9c000000 0 0x2300000>;
-			width = <1644>;
-			height = <3840>;
-			stride = <(1644 * 4)>;
+			/* Griffin BL initializes in 2.5k mode, not 4k */
+			width = <1096>;
+			height = <2560>;
+			stride = <(1096 * 4)>;
 			format = "a8r8g8b8";
 			/*
 			 * That's (going to be) a lot of clocks, but it's necessary due
@@ -126,7 +127,7 @@
 			reg = <0x0 0xffc00000 0x0 0x100000>;
 			record-size = <0x1000>;
 			console-size = <0x40000>;
-			msg-size = <0x20000 0x20000>;
+			pmsg-size = <0x20000>;
 			ecc-size = <16>;
 			no-map;
 		};
@@ -348,6 +349,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_3p0: ldo7 {
@@ -367,6 +371,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -1131,7 +1131,7 @@
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c7_default>;
-				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1692,12 +1692,12 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
-				reg = <0 0x01d87400 0 0x108>,
-				      <0 0x01d87600 0 0x1e0>,
-				      <0 0x01d87c00 0 0x1dc>,
-				      <0 0x01d87800 0 0x108>,
-				      <0 0x01d87a00 0 0x1e0>;
+			ufs_mem_phy_lanes: phy@1d87400 {
+				reg = <0 0x01d87400 0 0x16c>,
+				      <0 0x01d87600 0 0x200>,
+				      <0 0x01d87c00 0 0x200>,
+				      <0 0x01d87800 0 0x16c>,
+				      <0 0x01d87a00 0 0x200>;
 				#phy-cells = <0>;
 			};
 		};
@@ -3010,7 +3010,7 @@
 				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			usb_1_ssphy: lanes@88e9200 {
+			usb_1_ssphy: phy@88e9200 {
 				reg = <0 0x088e9200 0 0x200>,
 				      <0 0x088e9400 0 0x200>,
 				      <0 0x088e9c00 0 0x218>,
@@ -3043,7 +3043,7 @@
 				 <&gcc GCC_USB3_PHY_SEC_BCR>;
 			reset-names = "phy", "common";
 
-			usb_2_ssphy: lane@88eb200 {
+			usb_2_ssphy: phy@88eb200 {
 				reg = <0 0x088eb200 0 0x200>,
 				      <0 0x088eb400 0 0x200>,
 				      <0 0x088eb800 0 0x800>,
@@ -3094,8 +3094,8 @@
 
 			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 488 IRQ_TYPE_EDGE_BOTH>,
+				     <GIC_SPI 489 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -3139,8 +3139,8 @@
 
 			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 490 IRQ_TYPE_EDGE_BOTH>,
+				     <GIC_SPI 491 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
 					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
@@ -3359,7 +3359,7 @@
 			compatible = "qcom,apss-wdt-sm8150", "qcom,kpss-wdt";
 			reg = <0 0x17c10000 0 0x1000>;
 			clocks = <&sleep_clk>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		timer@17c20000 {
@@ -3434,9 +3434,9 @@
 			qcom,tcs-offset = <0xd00>;
 			qcom,drv-id = <2>;
 			qcom,tcs-config = <ACTIVE_TCS  2>,
-					  <SLEEP_TCS   1>,
-					  <WAKE_TCS    1>,
-					  <CONTROL_TCS 0>;
+					  <SLEEP_TCS   3>,
+					  <WAKE_TCS    3>,
+					  <CONTROL_TCS 1>;
 
 			rpmhcc: clock-controller {
 				compatible = "qcom,sm8150-rpmh-clk";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
@@ -13,3 +13,236 @@
 };
 
 /delete-node/ &vreg_l7f_1p8;
+
+&pm8009_gpios {
+	gpio-line-names = "NC", /* GPIO_1 */
+			  "CAM_PWR_LD_EN",
+			  "WIDEC_PWR_EN",
+			  "NC";
+};
+
+&pm8150_gpios {
+	gpio-line-names = "VOL_DOWN_N", /* GPIO_1 */
+			  "OPTION_2",
+			  "NC",
+			  "PM_SLP_CLK_IN",
+			  "OPTION_1",
+			  "NC",
+			  "NC",
+			  "SP_ARI_PWR_ALARM",
+			  "NC",
+			  "NC"; /* GPIO_10 */
+};
+
+&pm8150b_gpios {
+	gpio-line-names = "SNAPSHOT_N", /* GPIO_1 */
+			  "FOCUS_N",
+			  "NC",
+			  "NC",
+			  "RF_LCD_ID_EN",
+			  "NC",
+			  "NC",
+			  "LCD_ID",
+			  "NC",
+			  "WLC_EN_N", /* GPIO_10 */
+			  "NC",
+			  "RF_ID";
+};
+
+&pm8150l_gpios {
+	gpio-line-names = "NC", /* GPIO_1 */
+			  "PM3003A_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "AUX2_THERM",
+			  "BB_HP_EN",
+			  "FP_LDO_EN",
+			  "PMX_RESET_N",
+			  "AUX3_THERM", /* GPIO_10 */
+			  "DTV_PWR_EN",
+			  "PM3003A_MODE";
+};
+
+&tlmm {
+	gpio-line-names = "AP_CTI_IN", /* GPIO_0 */
+			  "MDM2AP_ERR_FATAL",
+			  "AP_CTI_OUT",
+			  "MDM2AP_STATUS",
+			  "NFC_I2C_SDA",
+			  "NFC_I2C_SCL",
+			  "NFC_EN",
+			  "NFC_CLK_REQ",
+			  "NFC_ESE_PWR_REQ",
+			  "DVDT_WRT_DET_AND",
+			  "SPK_AMP_RESET_N", /* GPIO_10 */
+			  "SPK_AMP_INT_N",
+			  "APPS_I2C_1_SDA",
+			  "APPS_I2C_1_SCL",
+			  "NC",
+			  "TX_GTR_THRES_IN",
+			  "HST_BT_UART_CTS",
+			  "HST_BT_UART_RFR",
+			  "HST_BT_UART_TX",
+			  "HST_BT_UART_RX",
+			  "HST_WLAN_EN", /* GPIO_20 */
+			  "HST_BT_EN",
+			  "RGBC_IR_PWR_EN",
+			  "FP_INT_N",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NFC_ESE_SPI_MISO",
+			  "NFC_ESE_SPI_MOSI",
+			  "NFC_ESE_SPI_SCLK", /* GPIO_30 */
+			  "NFC_ESE_SPI_CS_N",
+			  "WCD_RST_N",
+			  "NC",
+			  "SDM_DEBUG_UART_TX",
+			  "SDM_DEBUG_UART_RX",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "TS_INT_N",
+			  "FP_SPI_MISO", /* GPIO_40 */
+			  "FP_SPI_MOSI",
+			  "FP_SPI_SCLK",
+			  "FP_SPI_CS_N",
+			  "APPS_I2C_0_SDA",
+			  "APPS_I2C_0_SCL",
+			  "DISP_ERR_FG",
+			  "UIM2_DETECT_EN",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_50 */
+			  "NC",
+			  "MDM_UART_CTS",
+			  "MDM_UART_RFR",
+			  "MDM_UART_TX",
+			  "MDM_UART_RX",
+			  "AP2MDM_STATUS",
+			  "AP2MDM_ERR_FATAL",
+			  "MDM_IPC_HS_UART_TX",
+			  "MDM_IPC_HS_UART_RX",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "USB_CC_DIR",
+			  "DISP_VSYNC",
+			  "NC",
+			  "NC",
+			  "CAM_PWR_B_CS",
+			  "NC", /* GPIO_70 */
+			  "CAM_PWR_A_CS",
+			  "SBU_SW_SEL",
+			  "SBU_SW_OE",
+			  "FP_RESET_N",
+			  "FP_RESET_N",
+			  "DISP_RESET_N",
+			  "DEBUG_GPIO0",
+			  "TRAY_DET",
+			  "CAM2_RST_N",
+			  "PCIE0_RST_N",
+			  "PCIE0_CLK_REQ_N", /* GPIO_80 */
+			  "PCIE0_WAKE_N",
+			  "DVDT_ENABLE",
+			  "DVDT_WRT_DET_OR",
+			  "NC",
+			  "PCIE2_RST_N",
+			  "PCIE2_CLK_REQ_N",
+			  "PCIE2_WAKE_N",
+			  "MDM_VFR_IRQ0",
+			  "MDM_VFR_IRQ1",
+			  "SW_SERVICE", /* GPIO_90 */
+			  "CAM_SOF",
+			  "CAM1_RST_N",
+			  "CAM0_RST_N",
+			  "CAM0_MCLK",
+			  "CAM1_MCLK",
+			  "CAM2_MCLK",
+			  "CAM3_MCLK",
+			  "CAM4_MCLK",
+			  "TOF_RST_N",
+			  "NC", /* GPIO_100 */
+			  "CCI0_I2C_SDA",
+			  "CCI0_I2C_SCL",
+			  "CCI1_I2C_SDA",
+			  "CCI1_I2C_SCL_",
+			  "CCI2_I2C_SDA",
+			  "CCI2_I2C_SCL",
+			  "CCI3_I2C_SDA",
+			  "CCI3_I2C_SCL",
+			  "CAM3_RST_N",
+			  "NFC_DWL_REQ", /* GPIO_110 */
+			  "NFC_IRQ",
+			  "XVS",
+			  "NC",
+			  "RF_ID_EXTENSION",
+			  "SPK_AMP_I2C_SDA",
+			  "SPK_AMP_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "WLC_I2C_SDA",
+			  "WLC_I2C_SCL", /* GPIO_120 */
+			  "ACC_COVER_OPEN",
+			  "ALS_PROX_INT_N",
+			  "ACCEL_INT",
+			  "WLAN_SW_CTRL",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "UDON_SWITCH_SEL",
+			  "WDOG_DISABLE",
+			  "BAROMETER_INT",
+			  "NC", /* GPIO_130 */
+			  "NC",
+			  "FORCED_USB_BOOT",
+			  "NC",
+			  "NC",
+			  "WLC_INT_N",
+			  "NC",
+			  "NC",
+			  "RGBC_IR_INT",
+			  "NC",
+			  "NC", /* GPIO_140 */
+			  "NC",
+			  "BT_SLIMBUS_CLK",
+			  "BT_SLIMBUS_DATA",
+			  "HW_ID_0",
+			  "HW_ID_1",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0", /* GPIO_150 */
+			  "WCD_SWR_RX_DATA1",
+			  "SDM_DMIC_CLK1",
+			  "SDM_DMIC_DATA1",
+			  "SDM_DMIC_CLK2",
+			  "SDM_DMIC_DATA2",
+			  "SPK_AMP_I2S_CLK",
+			  "SPK_AMP_I2S_WS",
+			  "SPK_AMP_I2S_ASP_DIN",
+			  "SPK_AMP_I2S_ASP_DOUT",
+			  "COMPASS_I2C_SDA", /* GPIO_160 */
+			  "COMPASS_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "SSC_SPI_1_MISO",
+			  "SSC_SPI_1_MOSI",
+			  "SSC_SPI_1_CLK",
+			  "SSC_SPI_1_CS_N",
+			  "NC",
+			  "NC",
+			  "SSC_SENSOR_I2C_SDA", /* GPIO_170 */
+			  "SSC_SENSOR_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "HST_BLE_SNS_UART6_TX",
+			  "HST_BLE_SNS_UART6_RX",
+			  "HST_WLAN_UART_TX",
+			  "HST_WLAN_UART_RX";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
@@ -19,6 +19,8 @@
 };
 
 &gpio_keys {
+	pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &g_assist_n>;
+
 	g-assist-key {
 		label = "Google Assistant Key";
 		linux,code = <KEY_LEFTMETA>;
@@ -29,6 +31,247 @@
 	};
 };
 
+&pm8009_gpios {
+	gpio-line-names = "NC", /* GPIO_1 */
+			  "NC",
+			  "WIDEC_PWR_EN",
+			  "NC";
+};
+
+&pm8150_gpios {
+	gpio-line-names = "VOL_DOWN_N", /* GPIO_1 */
+			  "OPTION_2",
+			  "NC",
+			  "PM_SLP_CLK_IN",
+			  "OPTION_1",
+			  "G_ASSIST_N",
+			  "NC",
+			  "SP_ARI_PWR_ALARM",
+			  "NC",
+			  "NC"; /* GPIO_10 */
+
+	g_assist_n: g-assist-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pm8150b_gpios {
+	gpio-line-names = "SNAPSHOT_N", /* GPIO_1 */
+			  "FOCUS_N",
+			  "NC",
+			  "NC",
+			  "RF_LCD_ID_EN",
+			  "NC",
+			  "NC",
+			  "LCD_ID",
+			  "NC",
+			  "NC", /* GPIO_10 */
+			  "NC",
+			  "RF_ID";
+};
+
+&pm8150l_gpios {
+	gpio-line-names = "NC", /* GPIO_1 */
+			  "PM3003A_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "AUX2_THERM",
+			  "BB_HP_EN",
+			  "FP_LDO_EN",
+			  "PMX_RESET_N",
+			  "NC", /* GPIO_10 */
+			  "NC",
+			  "PM3003A_MODE";
+};
+
+&tlmm {
+	gpio-line-names = "AP_CTI_IN", /* GPIO_0 */
+			  "MDM2AP_ERR_FATAL",
+			  "AP_CTI_OUT",
+			  "MDM2AP_STATUS",
+			  "NFC_I2C_SDA",
+			  "NFC_I2C_SCL",
+			  "NFC_EN",
+			  "NFC_CLK_REQ",
+			  "NFC_ESE_PWR_REQ",
+			  "DVDT_WRT_DET_AND",
+			  "SPK_AMP_RESET_N", /* GPIO_10 */
+			  "SPK_AMP_INT_N",
+			  "APPS_I2C_1_SDA",
+			  "APPS_I2C_1_SCL",
+			  "NC",
+			  "TX_GTR_THRES_IN",
+			  "HST_BT_UART_CTS",
+			  "HST_BT_UART_RFR",
+			  "HST_BT_UART_TX",
+			  "HST_BT_UART_RX",
+			  "HST_WLAN_EN", /* GPIO_20 */
+			  "HST_BT_EN",
+			  "RGBC_IR_PWR_EN",
+			  "FP_INT_N",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NFC_ESE_SPI_MISO",
+			  "NFC_ESE_SPI_MOSI",
+			  "NFC_ESE_SPI_SCLK", /* GPIO_30 */
+			  "NFC_ESE_SPI_CS_N",
+			  "WCD_RST_N",
+			  "NC",
+			  "SDM_DEBUG_UART_TX",
+			  "SDM_DEBUG_UART_RX",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "TS_INT_N",
+			  "FP_SPI_MISO", /* GPIO_40 */
+			  "FP_SPI_MOSI",
+			  "FP_SPI_SCLK",
+			  "FP_SPI_CS_N",
+			  "APPS_I2C_0_SDA",
+			  "APPS_I2C_0_SCL",
+			  "DISP_ERR_FG",
+			  "UIM2_DETECT_EN",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_50 */
+			  "NC",
+			  "MDM_UART_CTS",
+			  "MDM_UART_RFR",
+			  "MDM_UART_TX",
+			  "MDM_UART_RX",
+			  "AP2MDM_STATUS",
+			  "AP2MDM_ERR_FATAL",
+			  "MDM_IPC_HS_UART_TX",
+			  "MDM_IPC_HS_UART_RX",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "USB_CC_DIR",
+			  "DISP_VSYNC",
+			  "NC",
+			  "NC",
+			  "CAM_PWR_B_CS",
+			  "NC", /* GPIO_70 */
+			  "FRONTC_PWR_EN",
+			  "SBU_SW_SEL",
+			  "SBU_SW_OE",
+			  "FP_RESET_N",
+			  "FP_RESET_N",
+			  "DISP_RESET_N",
+			  "DEBUG_GPIO0",
+			  "TRAY_DET",
+			  "CAM2_RST_N",
+			  "PCIE0_RST_N",
+			  "PCIE0_CLK_REQ_N", /* GPIO_80 */
+			  "PCIE0_WAKE_N",
+			  "DVDT_ENABLE",
+			  "DVDT_WRT_DET_OR",
+			  "NC",
+			  "PCIE2_RST_N",
+			  "PCIE2_CLK_REQ_N",
+			  "PCIE2_WAKE_N",
+			  "MDM_VFR_IRQ0",
+			  "MDM_VFR_IRQ1",
+			  "SW_SERVICE", /* GPIO_90 */
+			  "CAM_SOF",
+			  "CAM1_RST_N",
+			  "CAM0_RST_N",
+			  "CAM0_MCLK",
+			  "CAM1_MCLK",
+			  "CAM2_MCLK",
+			  "CAM3_MCLK",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_100 */
+			  "CCI0_I2C_SDA",
+			  "CCI0_I2C_SCL",
+			  "CCI1_I2C_SDA",
+			  "CCI1_I2C_SCL_",
+			  "CCI2_I2C_SDA",
+			  "CCI2_I2C_SCL",
+			  "CCI3_I2C_SDA",
+			  "CCI3_I2C_SCL",
+			  "CAM3_RST_N",
+			  "NFC_DWL_REQ", /* GPIO_110 */
+			  "NFC_IRQ",
+			  "XVS",
+			  "NC",
+			  "RF_ID_EXTENSION",
+			  "SPK_AMP_I2C_SDA",
+			  "SPK_AMP_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "ACC_COVER_OPEN",
+			  "ALS_PROX_INT_N",
+			  "ACCEL_INT",
+			  "WLAN_SW_CTRL",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "UDON_SWITCH_SEL",
+			  "WDOG_DISABLE",
+			  "BAROMETER_INT",
+			  "NC", /* GPIO_130 */
+			  "NC",
+			  "FORCED_USB_BOOT",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "RGBC_IR_INT",
+			  "NC",
+			  "NC", /* GPIO_140 */
+			  "NC",
+			  "BT_SLIMBUS_CLK",
+			  "BT_SLIMBUS_DATA",
+			  "HW_ID_0",
+			  "HW_ID_1",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0", /* GPIO_150 */
+			  "WCD_SWR_RX_DATA1",
+			  "SDM_DMIC_CLK1",
+			  "SDM_DMIC_DATA1",
+			  "SDM_DMIC_CLK2",
+			  "SDM_DMIC_DATA2",
+			  "SPK_AMP_I2S_CLK",
+			  "SPK_AMP_I2S_WS",
+			  "SPK_AMP_I2S_ASP_DIN",
+			  "SPK_AMP_I2S_ASP_DOUT",
+			  "COMPASS_I2C_SDA", /* GPIO_160 */
+			  "COMPASS_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "SSC_SPI_1_MISO",
+			  "SSC_SPI_1_MOSI",
+			  "SSC_SPI_1_CLK",
+			  "SSC_SPI_1_CS_N",
+			  "NC",
+			  "NC",
+			  "SSC_SENSOR_I2C_SDA", /* GPIO_170 */
+			  "SSC_SENSOR_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "HST_BLE_SNS_UART6_TX",
+			  "HST_BLE_SNS_UART6_RX",
+			  "HST_WLAN_UART_TX",
+			  "HST_WLAN_UART_RX";
+};
+
 &vreg_l2f_1p3 {
 	regulator-min-microvolt = <1200000>;
 	regulator-max-microvolt = <1200000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
@@ -26,9 +26,10 @@
 		framebuffer: framebuffer@9c000000 {
 			compatible = "simple-framebuffer";
 			reg = <0 0x9c000000 0 0x2300000>;
-			width = <1644>;
-			height = <3840>;
-			stride = <(1644 * 4)>;
+			/* pdx203 BL initializes in 2.5k mode, not 4k */
+			width = <1096>;
+			height = <2560>;
+			stride = <(1096 * 4)>;
 			format = "a8r8g8b8";
 			/*
 			 * That's a lot of clocks, but it's necessary due
@@ -50,12 +51,26 @@
 	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		/*
-		 * Camera focus (light press) and camera snapshot (full press)
-		 * seem not to work properly.. Adding the former one stalls the CPU
-		 * and the latter kills the volume down key for whatever reason. In any
-		 * case, they are both on &pm8150b_gpios: camera focus(2), camera snapshot(1).
-		 */
+		pinctrl-0 = <&focus_n &snapshot_n &vol_down_n>;
+		pinctrl-names = "default";
+
+		key-camera-focus {
+			label = "Camera Focus";
+			linux,code = <KEY_CAMERA_FOCUS>;
+			gpios = <&pm8150b_gpios 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+
+		key-camera-snapshot {
+			label = "Camera Snapshot";
+			linux,code = <KEY_CAMERA>;
+			gpios = <&pm8150b_gpios 1 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
 
 		vol-down {
 			label = "Volume Down";
@@ -111,7 +126,7 @@
 			reg = <0x0 0xffc00000 0x0 0x100000>;
 			record-size = <0x1000>;
 			console-size = <0x40000>;
-			msg-size = <0x20000 0x20000>;
+			pmsg-size = <0x20000>;
 			ecc-size = <16>;
 			no-map;
 		};
@@ -317,6 +332,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_2p85: ldo7 {
@@ -339,6 +357,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
@@ -511,6 +532,34 @@
 	vdda-pll-supply = <&vreg_l9a_1p2>;
 };
 
+&pm8150_gpios {
+	vol_down_n: vol-down-n-state {
+		pins = "gpio1";
+		function = "normal";
+		power-source = <0>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pm8150b_gpios {
+	snapshot_n: snapshot-n-state {
+		pins = "gpio1";
+		function = "normal";
+		power-source = <0>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	focus_n: focus-n-state {
+		pins = "gpio2";
+		function = "normal";
+		power-source = <0>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -585,7 +634,7 @@
 		pins = "gpio39";
 		function = "gpio";
 		drive-strength = <2>;
-		bias-disabled;
+		bias-disable;
 		input-enable;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -82,7 +82,7 @@
 
 		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+			clock-frequency = <32764>;
 			#clock-cells = <0>;
 		};
 	};
@@ -97,7 +97,7 @@
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <448>;
-			dynamic-power-coefficient = <205>;
+			dynamic-power-coefficient = <105>;
 			next-level-cache = <&L2_0>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -116,7 +116,7 @@
 			reg = <0x0 0x100>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <448>;
-			dynamic-power-coefficient = <205>;
+			dynamic-power-coefficient = <105>;
 			next-level-cache = <&L2_100>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -132,7 +132,7 @@
 			reg = <0x0 0x200>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <448>;
-			dynamic-power-coefficient = <205>;
+			dynamic-power-coefficient = <105>;
 			next-level-cache = <&L2_200>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -148,7 +148,7 @@
 			reg = <0x0 0x300>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <448>;
-			dynamic-power-coefficient = <205>;
+			dynamic-power-coefficient = <105>;
 			next-level-cache = <&L2_300>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
@@ -1393,8 +1393,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
-				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
 
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
@@ -1434,11 +1434,12 @@
 			phys = <&pcie0_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>;
-			enable-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie0_default_state>;
+			dma-coherent;
 
 			status = "disabled";
 		};
@@ -1463,7 +1464,7 @@
 
 			status = "disabled";
 
-			pcie0_lane: lanes@1c06200 {
+			pcie0_lane: phy@1c06200 {
 				reg = <0 0x1c06200 0 0x170>, /* tx */
 				      <0 0x1c06400 0 0x200>, /* rx */
 				      <0 0x1c06800 0 0x1f0>, /* pcs */
@@ -1472,6 +1473,8 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
+
+				#clock-cells = <0>;
 				clock-output-names = "pcie_0_pipe_clk";
 			};
 		};
@@ -1492,10 +1495,10 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
 
-			interrupts = <GIC_SPI 306 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
@@ -1538,11 +1541,12 @@
 			phys = <&pcie1_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>;
-			enable-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie1_default_state>;
+			dma-coherent;
 
 			status = "disabled";
 		};
@@ -1567,7 +1571,7 @@
 
 			status = "disabled";
 
-			pcie1_lane: lanes@1c0e200 {
+			pcie1_lane: phy@1c0e200 {
 				reg = <0 0x1c0e200 0 0x170>, /* tx0 */
 				      <0 0x1c0e400 0 0x200>, /* rx0 */
 				      <0 0x1c0ea00 0 0x1f0>, /* pcs */
@@ -1578,6 +1582,8 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
+
+				#clock-cells = <0>;
 				clock-output-names = "pcie_1_pipe_clk";
 			};
 		};
@@ -1598,10 +1604,10 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x01000000 0x0 0x64200000 0x0 0x64200000 0x0 0x100000>,
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x64200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x64300000 0x0 0x64300000 0x0 0x3d00000>;
 
-			interrupts = <GIC_SPI 236 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
@@ -1644,11 +1650,12 @@
 			phys = <&pcie2_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>;
-			enable-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie2_default_state>;
+			dma-coherent;
 
 			status = "disabled";
 		};
@@ -1673,7 +1680,7 @@
 
 			status = "disabled";
 
-			pcie2_lane: lanes@1c16200 {
+			pcie2_lane: phy@1c16200 {
 				reg = <0 0x1c16200 0 0x170>, /* tx0 */
 				      <0 0x1c16400 0 0x200>, /* rx0 */
 				      <0 0x1c16a00 0 0x1f0>, /* pcs */
@@ -1684,6 +1691,8 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
+
+				#clock-cells = <0>;
 				clock-output-names = "pcie_2_pipe_clk";
 			};
 		};
@@ -1750,12 +1759,14 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
-				reg = <0 0x01d87400 0 0x108>,
-				      <0 0x01d87600 0 0x1e0>,
-				      <0 0x01d87c00 0 0x1dc>,
-				      <0 0x01d87800 0 0x108>,
-				      <0 0x01d87a00 0 0x1e0>;
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			ufs_mem_phy_lanes: phy@1d87400 {
+				reg = <0 0x01d87400 0 0x16c>,
+				      <0 0x01d87600 0 0x200>,
+				      <0 0x01d87c00 0 0x200>,
+				      <0 0x01d87800 0 0x16c>,
+				      <0 0x01d87a00 0 0x200>;
 				#phy-cells = <0>;
 			};
 		};
@@ -1927,7 +1938,7 @@
 					pins = "gpio7";
 					function = "dmic1_data";
 					drive-strength = <2>;
-					pull-down;
+					bias-pull-down;
 					input-enable;
 				};
 			};
@@ -2300,15 +2311,11 @@
 			dp_phy: dp-phy@88ea200 {
 				reg = <0 0x088ea200 0 0x200>,
 				      <0 0x088ea400 0 0x200>,
-				      <0 0x088eac00 0 0x400>,
+				      <0 0x088eaa00 0 0x200>,
 				      <0 0x088ea600 0 0x200>,
-				      <0 0x088ea800 0 0x200>,
-				      <0 0x088eaa00 0 0x100>;
+				      <0 0x088ea800 0 0x200>;
 				#phy-cells = <0>;
 				#clock-cells = <1>;
-				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb3_phy_pipe_clk_src";
 			};
 		};
 
@@ -2330,7 +2337,7 @@
 				 <&gcc GCC_USB3_PHY_SEC_BCR>;
 			reset-names = "phy", "common";
 
-			usb_2_ssphy: lanes@88eb200 {
+			usb_2_ssphy: phy@88eb200 {
 				reg = <0 0x088eb200 0 0x200>,
 				      <0 0x088eb400 0 0x200>,
 				      <0 0x088eb800 0 0x800>;
@@ -3942,7 +3949,7 @@
 			compatible = "qcom,apss-wdt-sm8250", "qcom,kpss-wdt";
 			reg = <0 0x17c10000 0 0x1000>;
 			clocks = <&sleep_clk>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		timer@17c20000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -108,6 +108,9 @@
 			regulator-max-microvolt = <888000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l6b_1p2: ldo6 {
@@ -116,6 +119,9 @@
 			regulator-max-microvolt = <1208000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7b_2p96: ldo7 {
@@ -124,6 +130,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l9b_1p2: ldo9 {
@@ -132,6 +141,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -32,7 +32,25 @@
 
 		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32000>;
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+
+		ufs_phy_rx_symbol_0_clk: ufs-phy-rx-symbol-0 {
+			compatible = "fixed-clock";
+			clock-frequency = <1000>;
+			#clock-cells = <0>;
+		};
+
+		ufs_phy_rx_symbol_1_clk: ufs-phy-rx-symbol-1 {
+			compatible = "fixed-clock";
+			clock-frequency = <1000>;
+			#clock-cells = <0>;
+		};
+
+		ufs_phy_tx_symbol_0_clk: ufs-phy-tx-symbol-0 {
+			compatible = "fixed-clock";
+			clock-frequency = <1000>;
 			#clock-cells = <0>;
 		};
 	};
@@ -43,7 +61,7 @@
 
 		CPU0: cpu@0 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a55";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
@@ -60,7 +78,7 @@
 
 		CPU1: cpu@100 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a55";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
 			next-level-cache = <&L2_100>;
@@ -74,7 +92,7 @@
 
 		CPU2: cpu@200 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a55";
 			reg = <0x0 0x200>;
 			enable-method = "psci";
 			next-level-cache = <&L2_200>;
@@ -88,7 +106,7 @@
 
 		CPU3: cpu@300 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a55";
 			reg = <0x0 0x300>;
 			enable-method = "psci";
 			next-level-cache = <&L2_300>;
@@ -102,7 +120,7 @@
 
 		CPU4: cpu@400 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a78";
 			reg = <0x0 0x400>;
 			enable-method = "psci";
 			next-level-cache = <&L2_400>;
@@ -116,7 +134,7 @@
 
 		CPU5: cpu@500 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a78";
 			reg = <0x0 0x500>;
 			enable-method = "psci";
 			next-level-cache = <&L2_500>;
@@ -131,7 +149,7 @@
 
 		CPU6: cpu@600 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-a78";
 			reg = <0x0 0x600>;
 			enable-method = "psci";
 			next-level-cache = <&L2_600>;
@@ -145,7 +163,7 @@
 
 		CPU7: cpu@700 {
 			device_type = "cpu";
-			compatible = "qcom,kryo685";
+			compatible = "arm,cortex-x1";
 			reg = <0x0 0x700>;
 			enable-method = "psci";
 			next-level-cache = <&L2_700>;
@@ -443,8 +461,30 @@
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
-			clock-names = "bi_tcxo", "sleep_clk";
-			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+			clock-names = "bi_tcxo",
+				      "sleep_clk",
+				      "pcie_0_pipe_clk",
+				      "pcie_1_pipe_clk",
+				      "ufs_card_rx_symbol_0_clk",
+				      "ufs_card_rx_symbol_1_clk",
+				      "ufs_card_tx_symbol_0_clk",
+				      "ufs_phy_rx_symbol_0_clk",
+				      "ufs_phy_rx_symbol_1_clk",
+				      "ufs_phy_tx_symbol_0_clk",
+				      "usb3_phy_wrapper_gcc_usb30_pipe_clk",
+				      "usb3_uni_phy_sec_gcc_usb30_pipe_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&sleep_clk>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <&ufs_phy_rx_symbol_0_clk>,
+				 <&ufs_phy_rx_symbol_1_clk>,
+				 <&ufs_phy_tx_symbol_0_clk>,
+				 <0>,
+				 <0>;
 		};
 
 		ipcc: mailbox@408000 {
@@ -696,6 +736,8 @@
 			interconnect-names = "memory",
 					     "config";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&ipa_smp2p_out 0>,
 					   <&ipa_smp2p_out 1>;
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
@@ -712,7 +754,7 @@
 
 		mpss: remoteproc@4080000 {
 			compatible = "qcom,sm8350-mpss-pas";
-			reg = <0x0 0x04080000 0x0 0x4040>;
+			reg = <0x0 0x04080000 0x0 0x10000>;
 
 			interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
 					      <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
@@ -939,7 +981,7 @@
 			qcom,tcs-offset = <0xd00>;
 			qcom,drv-id = <2>;
 			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
-					  <WAKE_TCS    3>, <CONTROL_TCS 1>;
+					  <WAKE_TCS    3>, <CONTROL_TCS 0>;
 
 			rpmhcc: clock-controller {
 				compatible = "qcom,sm8350-rpmh-clk";
@@ -1010,6 +1052,13 @@
 			      <0 0x18593000 0 0x1000>;
 			reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
 
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dcvsh-irq-0",
+					  "dcvsh-irq-1",
+					  "dcvsh-irq-2";
+
 			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
 			clock-names = "xo", "alternate";
 
@@ -1060,17 +1109,16 @@
 				<75000000 300000000>,
 				<0 0>,
 				<0 0>,
-				<75000000 300000000>,
-				<75000000 300000000>;
+				<0 0>,
+				<0 0>;
 			status = "disabled";
 		};
 
 		ufs_mem_phy: phy@1d87000 {
 			compatible = "qcom,sm8350-qmp-ufs-phy";
-			reg = <0 0x01d87000 0 0xe10>;
+			reg = <0 0x01d87000 0 0x1c4>;
 			#address-cells = <2>;
 			#size-cells = <2>;
-			#clock-cells = <1>;
 			ranges;
 			clock-names = "ref",
 				      "ref_aux";
@@ -1081,12 +1129,12 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
-				reg = <0 0x01d87400 0 0x108>,
-				      <0 0x01d87600 0 0x1e0>,
-				      <0 0x01d87c00 0 0x1dc>,
-				      <0 0x01d87800 0 0x108>,
-				      <0 0x01d87a00 0 0x1e0>;
+			ufs_mem_phy_lanes: phy@1d87400 {
+				reg = <0 0x01d87400 0 0x188>,
+				      <0 0x01d87600 0 0x200>,
+				      <0 0x01d87c00 0 0x200>,
+				      <0 0x01d87800 0 0x188>,
+				      <0 0x01d87a00 0 0x200>;
 				#phy-cells = <0>;
 				#clock-cells = <0>;
 			};
@@ -1205,7 +1253,6 @@
 			      <0 0x088e8000 0 0x20>;
 			reg-names = "reg-base", "dp_com";
 			status = "disabled";
-			#clock-cells = <1>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
@@ -1238,7 +1285,6 @@
 			compatible = "qcom,sm8350-qmp-usb3-uni-phy";
 			reg = <0 0x088eb000 0 0x200>;
 			status = "disabled";
-			#clock-cells = <1>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
@@ -2185,7 +2231,7 @@
 			};
 		};
 
-		camera-thermal-bottom {
+		cam-thermal-bottom {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
@@ -146,7 +146,7 @@
 		};
 	};
 
-	reg_audio: regulator_audio {
+	reg_audio: regulator-audio {
 		compatible = "regulator-fixed";
 		regulator-name = "audio-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -174,7 +174,7 @@
 		vin-supply = <&reg_lcd>;
 	};
 
-	reg_cam0: regulator_camera {
+	reg_cam0: regulator-cam0 {
 		compatible = "regulator-fixed";
 		regulator-name = "reg_cam0";
 		regulator-min-microvolt = <1800000>;
@@ -183,7 +183,7 @@
 		enable-active-high;
 	};
 
-	reg_cam1: regulator_camera {
+	reg_cam1: regulator-cam1 {
 		compatible = "regulator-fixed";
 		regulator-name = "reg_cam1";
 		regulator-min-microvolt = <1800000>;
@@ -432,20 +432,6 @@
 		};
 	};
 
-	/* 0 - lcd_reset */
-	/* 1 - lcd_pwr */
-	/* 2 - lcd_select */
-	/* 3 - backlight-enable */
-	/* 4 - Touch_shdwn */
-	/* 5 - LCD_H_pol */
-	/* 6 - lcd_V_pol */
-	gpio_exp1: gpio@20 {
-		compatible = "onnn,pca9654";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	touchscreen@26 {
 		compatible = "ilitek,ili2117";
 		reg = <0x26>;
@@ -477,6 +463,16 @@
 			};
 		};
 	};
+
+	gpio_exp1: gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "lcd_reset", "lcd_pwr", "lcd_select",
+				  "backlight-enable", "Touch_shdwn",
+				  "LCD_H_pol", "lcd_V_pol";
+	};
 };
 
 &lvds0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
@@ -50,6 +50,7 @@
 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&phy0>;
 	rx-internal-delay-ps = <1800>;
 	tx-internal-delay-ps = <2000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/cat875.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/cat875.dtsi
@@ -18,6 +18,7 @@
 	pinctrl-names = "default";
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
@@ -2784,7 +2784,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2799,7 +2799,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2814,7 +2814,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a774b1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a774b1.dtsi
@@ -2629,7 +2629,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2644,7 +2644,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2659,7 +2659,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a774c0.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a774c0.dtsi
@@ -49,17 +49,14 @@
 		opp-shared;
 		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
-			opp-microvolt = <820000>;
 			clock-latency-ns = <300000>;
 		};
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <820000>;
 			clock-latency-ns = <300000>;
 		};
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <820000>;
 			clock-latency-ns = <300000>;
 			opp-suspend;
 		};
@@ -1953,7 +1950,7 @@
 		cpu-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
-			thermal-sensors = <&thermal 0>;
+			thermal-sensors = <&thermal>;
 			sustainable-power = <717>;
 
 			cooling-maps {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a774e1.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a774e1.dtsi
@@ -2904,7 +2904,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2919,7 +2919,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2934,7 +2934,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a77951.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a77951.dtsi
@@ -3375,7 +3375,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -3390,7 +3390,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -3405,7 +3405,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a77960.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a77960.dtsi
@@ -2972,7 +2972,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2987,7 +2987,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -3002,7 +3002,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a77961.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a77961.dtsi
@@ -2719,7 +2719,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2734,7 +2734,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2749,7 +2749,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -2784,7 +2784,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2799,7 +2799,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2814,7 +2814,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a77980.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a77980.dtsi
@@ -1580,7 +1580,7 @@
 	};
 
 	thermal-zones {
-		thermal-sensor-1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -1599,7 +1599,7 @@
 			};
 		};
 
-		thermal-sensor-2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a77990.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a77990.dtsi
@@ -60,17 +60,14 @@
 		opp-shared;
 		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
-			opp-microvolt = <820000>;
 			clock-latency-ns = <300000>;
 		};
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <820000>;
 			clock-latency-ns = <300000>;
 		};
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <820000>;
 			clock-latency-ns = <300000>;
 			opp-suspend;
 		};
@@ -2102,7 +2099,7 @@
 		cpu-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
-			thermal-sensors = <&thermal 0>;
+			thermal-sensors = <&thermal>;
 			sustainable-power = <717>;
 
 			cooling-maps {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
@@ -583,8 +583,8 @@
 
 		avb0: ethernet@e6800000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
-			reg = <0 0xe6800000 0 0x800>;
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6800000 0 0x1000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
@@ -631,8 +631,8 @@
 
 		avb1: ethernet@e6810000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
-			reg = <0 0xe6810000 0 0x800>;
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6810000 0 0x1000>;
 			interrupts = <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
@@ -679,7 +679,7 @@
 
 		avb2: ethernet@e6820000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6820000 0 0x1000>;
 			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
@@ -727,7 +727,7 @@
 
 		avb3: ethernet@e6830000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6830000 0 0x1000>;
 			interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
@@ -775,7 +775,7 @@
 
 		avb4: ethernet@e6840000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6840000 0 0x1000>;
 			interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
@@ -823,7 +823,7 @@
 
 		avb5: ethernet@e6850000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6850000 0 0x1000>;
 			interrupts = <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>,
@@ -935,7 +935,7 @@
 
 		msiof0: spi@e6e90000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6e90000 0 0x0064>;
 			interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 618>;
@@ -950,7 +950,7 @@
 
 		msiof1: spi@e6ea0000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6ea0000 0 0x0064>;
 			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 619>;
@@ -965,7 +965,7 @@
 
 		msiof2: spi@e6c00000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c00000 0 0x0064>;
 			interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 620>;
@@ -980,7 +980,7 @@
 
 		msiof3: spi@e6c10000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c10000 0 0x0064>;
 			interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 621>;
@@ -995,7 +995,7 @@
 
 		msiof4: spi@e6c20000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c20000 0 0x0064>;
 			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 622>;
@@ -1010,7 +1010,7 @@
 
 		msiof5: spi@e6c28000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c28000 0 0x0064>;
 			interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 623>;
@@ -1149,7 +1149,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -1163,7 +1163,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -1177,7 +1177,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
@@ -1191,7 +1191,7 @@
 			};
 		};
 
-		sensor_thermal4: sensor-thermal4 {
+		sensor4_thermal: sensor4-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 3>;
@@ -1205,7 +1205,7 @@
 			};
 		};
 
-		sensor_thermal5: sensor-thermal5 {
+		sensor5_thermal: sensor5-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 4>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -300,8 +300,8 @@
 			#interrupt-cells = <3>;
 			#address-cells = <0>;
 			interrupt-controller;
-			reg = <0x0 0x11900000 0 0x40000>,
-			      <0x0 0x11940000 0 0x60000>;
+			reg = <0x0 0x11900000 0 0x20000>,
+			      <0x0 0x11940000 0 0x40000>;
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
@@ -270,7 +270,7 @@
 	};
 
 	scif1_pins: scif1 {
-		groups = "scif1_data_b", "scif1_ctrl";
+		groups = "scif1_data_b";
 		function = "scif1";
 	};
 
@@ -330,7 +330,6 @@
 &scif1 {
 	pinctrl-0 = <&scif1_pins>;
 	pinctrl-names = "default";
-	uart-has-rtscts;
 
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/px30-engicam-px30-core.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/px30-engicam-px30-core.dtsi
@@ -2,8 +2,8 @@
 /*
  * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 #include <dt-bindings/gpio/gpio.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/px30.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/px30.dtsi
@@ -585,6 +585,7 @@
 		clock-names = "spiclk", "apb_pclk";
 		dmas = <&dmac 12>, <&dmac 13>;
 		dma-names = "tx", "rx";
+		num-cs = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi0_clk &spi0_csn &spi0_miso &spi0_mosi>;
 		#address-cells = <1>;
@@ -600,6 +601,7 @@
 		clock-names = "spiclk", "apb_pclk";
 		dmas = <&dmac 14>, <&dmac 15>;
 		dma-names = "tx", "rx";
+		num-cs = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi1_clk &spi1_csn0 &spi1_csn1 &spi1_miso &spi1_mosi>;
 		#address-cells = <1>;
@@ -711,7 +713,7 @@
 		clock-names = "pclk", "timer";
 	};
 
-	dmac: dmac@ff240000 {
+	dmac: dma-controller@ff240000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xff240000 0x0 0x4000>;
 		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
@@ -19,7 +19,7 @@
 		stdout-path = "serial2:1500000n8";
 	};
 
-	ir_rx {
+	ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
@@ -36,14 +36,14 @@
 
 		power_led: led-0 {
 			label = "firefly:red:power";
-			linux,default-trigger = "ir-power-click";
+			linux,default-trigger = "default-on";
 			default-state = "on";
 			gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
 		};
 
 		user_led: led-1 {
 			label = "firefly:blue:user";
-			linux,default-trigger = "ir-user-click";
+			linux,default-trigger = "rc-feedback";
 			default-state = "off";
 			gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_HIGH>;
 		};
@@ -97,7 +97,7 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 		regulator-boot-on;
-		vim-supply = <&vcc_io>;
+		vin-supply = <&vcc_io>;
 	};
 
 	vdd_core: vdd-core {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -96,7 +96,6 @@
 			linux,default-trigger = "heartbeat";
 			gpios = <&rk805 1 GPIO_ACTIVE_LOW>;
 			default-state = "on";
-			mode = <0x23>;
 		};
 
 		user_led: led-1 {
@@ -104,7 +103,6 @@
 			linux,default-trigger = "mmc1";
 			gpios = <&rk805 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
-			mode = <0x05>;
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
@@ -186,8 +186,8 @@
 	rk805: pmic@18 {
 		compatible = "rockchip,rk805";
 		reg = <0x18>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		#clock-cells = <1>;
 		clock-output-names = "xin32k", "rk805-clkout2";
 		gpio-controller;
@@ -332,7 +332,7 @@
 
 	pmic {
 		pmic_int_l: pmic-int-l {
-			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -302,6 +302,7 @@
 
 			power-domain@RK3328_PD_HEVC {
 				reg = <RK3328_PD_HEVC>;
+				clocks = <&cru SCLK_VENC_CORE>;
 				#power-domain-cells = <0>;
 			};
 			power-domain@RK3328_PD_VIDEO {
@@ -489,7 +490,7 @@
 		status = "disabled";
 	};
 
-	dmac: dmac@ff1f0000 {
+	dmac: dma-controller@ff1f0000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xff1f0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
@@ -599,7 +600,7 @@
 
 	gpu: gpu@ff300000 {
 		compatible = "rockchip,rk3328-mali", "arm,mali-450";
-		reg = <0x0 0xff300000 0x0 0x40000>;
+		reg = <0x0 0xff300000 0x0 0x30000>;
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
@@ -711,8 +712,7 @@
 		compatible = "rockchip,rk3328-dw-hdmi";
 		reg = <0x0 0xff3c0000 0x0 0x20000>;
 		reg-io-width = <4>;
-		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru PCLK_HDMI>,
 			 <&cru SCLK_HDMI_SFC>,
 			 <&cru SCLK_RTC32K>;
@@ -728,11 +728,20 @@
 		status = "disabled";
 
 		ports {
-			hdmi_in: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hdmi_in: port@0 {
+				reg = <0>;
+
 				hdmi_in_vop: endpoint {
 					remote-endpoint = <&vop_out_hdmi>;
 				};
 			};
+
+			hdmi_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};
 
@@ -798,8 +807,8 @@
 			<0>, <24000000>,
 			<24000000>, <24000000>,
 			<15000000>, <15000000>,
-			<100000000>, <100000000>,
-			<100000000>, <100000000>,
+			<300000000>, <100000000>,
+			<400000000>, <100000000>,
 			<50000000>, <100000000>,
 			<100000000>, <100000000>,
 			<50000000>, <50000000>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
@@ -60,7 +60,6 @@
 			fan: fan@18 {
 				compatible = "ti,amc6821";
 				reg = <0x18>;
-				#cooling-cells = <2>;
 			};
 
 			rtc_twi: rtc@6f {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3368.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3368.dtsi
@@ -678,6 +678,7 @@
 		dma-names = "tx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spdif_tx>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
@@ -689,6 +690,7 @@
 		clocks = <&cru SCLK_I2S_2CH>, <&cru HCLK_I2S_2CH>;
 		dmas = <&dmac_bus 6>, <&dmac_bus 7>;
 		dma-names = "tx", "rx";
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
@@ -702,6 +704,7 @@
 		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s_8ch_bus>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
@@ -770,8 +770,8 @@
 	sd-uhs-sdr104;
 
 	/* Power supply */
-	vqmmc-supply = &vcc1v8_s3;	/* IO line */
-	vmmc-supply = &vcc_sdio;	/* card's power */
+	vqmmc-supply = <&vcc1v8_s3>;	/* IO line */
+	vmmc-supply = <&vcc_sdio>;	/* card's power */
 
 	#address-cells = <1>;
 	#size-cells = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
@@ -87,3 +87,8 @@
 		};
 	};
 };
+
+&wlan_host_wake_l {
+	/* Kevin has an external pull up, but Bob does not. */
+	rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
@@ -237,6 +237,14 @@
 &edp {
 	status = "okay";
 
+	/*
+	 * eDP PHY/clk don't sync reliably at anything other than 24 MHz. Only
+	 * set this here, because rk3399-gru.dtsi ensures we can generate this
+	 * off GPLL=600MHz, whereas some other RK3399 boards may not.
+	 */
+	assigned-clocks = <&cru PCLK_EDP>;
+	assigned-clock-rates = <24000000>;
+
 	ports {
 		edp_out: port@1 {
 			reg = <1>;
@@ -395,6 +403,7 @@
 	};
 
 	wlan_host_wake_l: wlan-host-wake-l {
+		/* Kevin has an external pull up, but Bob does not */
 		rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -286,7 +286,7 @@
 
 	sound: sound {
 		compatible = "rockchip,rk3399-gru-sound";
-		rockchip,cpu = <&i2s0 &i2s2>;
+		rockchip,cpu = <&i2s0 &spdif>;
 	};
 };
 
@@ -437,10 +437,6 @@
 	status = "okay";
 };
 
-&i2s2 {
-	status = "okay";
-};
-
 &io_domains {
 	status = "okay";
 
@@ -537,6 +533,17 @@
 	vqmmc-supply = <&ppvar_sd_card_io>;
 };
 
+&spdif {
+	status = "okay";
+
+	/*
+	 * SPDIF is routed internally to DP; we either don't use these pins, or
+	 * mux them to something else.
+	 */
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+};
+
 &spi1 {
 	status = "okay";
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
@@ -705,7 +705,6 @@
 &sdhci {
 	bus-width = <8>;
 	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
 	non-removable;
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
@@ -269,6 +269,7 @@
 		clock-output-names = "xin32k", "rk808-clkout2";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
 		vcc1-supply = <&vcc5v0_sys>;
 		vcc2-supply = <&vcc5v0_sys>;
 		vcc3-supply = <&vcc5v0_sys>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
@@ -55,7 +55,7 @@
 		regulator-boot-on;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		vim-supply = <&vcc3v3_sys>;
+		vin-supply = <&vcc3v3_sys>;
 	};
 
 	vcc3v3_sys: vcc3v3-sys {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts
@@ -117,7 +117,7 @@
 };
 
 &u2phy1_host {
-	status = "disabled";
+	phy-supply = <&vdd_5v>;
 };
 
 &uart0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
@@ -31,12 +31,12 @@
 	backlight: edp-backlight {
 		compatible = "pwm-backlight";
 		power-supply = <&vcc_12v>;
-		pwms = <&pwm0 0 740740 0>;
+		pwms = <&pwm0 0 125000 0>;
 	};
 
 	bat: battery {
 		compatible = "simple-battery";
-		charge-full-design-microamp-hours = <9800000>;
+		charge-full-design-microamp-hours = <10000000>;
 		voltage-max-design-microvolt = <4350000>;
 		voltage-min-design-microvolt = <3000000>;
 	};
@@ -385,10 +385,6 @@
 	};
 };
 
-&cdn_dp {
-	status = "okay";
-};
-
 &cpu_b0 {
 	cpu-supply = <&vdd_cpu_b>;
 };
@@ -794,7 +790,6 @@
 };
 
 &pcie0 {
-	bus-scan-delay-ms = <1000>;
 	ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
 	num-lanes = <4>;
 	pinctrl-names = "default";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
@@ -207,7 +207,7 @@
 	cap-sd-highspeed;
 	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
 	disable-wp;
-	max-frequency = <150000000>;
+	max-frequency = <40000000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
 	vmmc-supply = <&vcc3v3_baseboard>;
@@ -232,6 +232,7 @@
 
 &usbdrd_dwc3_0 {
 	dr_mode = "otg";
+	extcon = <&extcon_usb3>;
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
@@ -25,6 +25,13 @@
 		};
 	};
 
+	extcon_usb3: extcon-usb3 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_id>;
+	};
+
 	clkin_gmac: external-gmac-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -55,7 +62,6 @@
 	vcc5v0_host: vcc5v0-host-regulator {
 		compatible = "regulator-fixed";
 		gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>;
-		enable-active-low;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vcc5v0_host_en>;
 		regulator-name = "vcc5v0_host";
@@ -102,6 +108,22 @@
 	drive-impedance-ohm = <33>;
 };
 
+&gpio3 {
+	/*
+	 * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
+	 * eMMC and SPI flash powered-down initially (in fact it keeps the
+	 * reset signal asserted). BIOS_DISABLE_OVERRIDE pin allows to override
+	 * that signal so that eMMC and SPI can be used regardless of the state
+	 * of the signal.
+	 */
+	bios-disable-override-hog {
+		gpios = <RK_PD5 GPIO_ACTIVE_LOW>;
+		gpio-hog;
+		line-name = "bios_disable_override";
+		output-high;
+	};
+};
+
 &gmac {
 	assigned-clocks = <&cru SCLK_RMII_SRC>;
 	assigned-clock-parents = <&clkin_gmac>;
@@ -114,7 +136,7 @@
 	snps,reset-active-low;
 	snps,reset-delays-us = <0 10000 50000>;
 	tx_delay = <0x10>;
-	rx_delay = <0x10>;
+	rx_delay = <0x23>;
 	status = "okay";
 };
 
@@ -384,16 +406,27 @@
 	gpio1830-supply = <&vcc_1v8>;
 };
 
-&pmu_io_domains {
-	status = "okay";
-	pmu1830-supply = <&vcc_1v8>;
-};
-
-&pwm2 {
-	status = "okay";
+&pcie_clkreqn_cpm {
+	rockchip,pins =
+		<2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_up>;
 };
 
 &pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&q7_thermal_pin &bios_disable_override_hog_pin>;
+
+	gpios {
+		bios_disable_override_hog_pin: bios-disable-override-hog-pin {
+			rockchip,pins =
+				<3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		q7_thermal_pin: q7-thermal-pin {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
 	i2c8 {
 		i2c8_xfer_a: i2c8-xfer {
 			rockchip,pins =
@@ -422,9 +455,31 @@
 			  <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	usb3 {
+		usb3_id: usb3-id {
+			rockchip,pins =
+			  <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	status = "okay";
+	pmu1830-supply = <&vcc_1v8>;
+};
+
+&pwm2 {
+	status = "okay";
 };
 
 &sdhci {
+	/*
+	 * Signal integrity isn't great at 200MHz but 100MHz has proven stable
+	 * enough.
+	 */
+	max-frequency = <100000000>;
+
 	bus-width = <8>;
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
@@ -36,6 +36,29 @@
 		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
 	};
 
+	sound {
+		compatible = "audio-graph-card";
+		label = "Analog";
+		dais = <&i2s0_p0>;
+	};
+
+	sound-dit {
+		compatible = "audio-graph-card";
+		label = "SPDIF";
+		dais = <&spdif_p0>;
+	};
+
+	spdif-dit {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+
+		port {
+			dit_p0_0: endpoint {
+				remote-endpoint = <&spdif_p0_0>;
+			};
+		};
+	};
+
 	vcc12v_dcin: dc-12v {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc12v_dcin";
@@ -98,24 +121,25 @@
 		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc5v0_typec: vcc5v0-typec-regulator {
+	vbus_typec: vbus-typec-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
 		gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vcc5v0_typec_en>;
-		regulator-name = "vcc5v0_typec";
+		regulator-name = "vbus_typec";
 		regulator-always-on;
 		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc_lan: vcc3v3-phy-regulator {
+	vcc3v3_lan: vcc3v3-lan-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_lan";
+		regulator-name = "vcc3v3_lan";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
 	};
 
 	vdd_log: vdd-log {
@@ -162,7 +186,7 @@
 	assigned-clocks = <&cru SCLK_RMII_SRC>;
 	assigned-clock-parents = <&clkin_gmac>;
 	clock_in_out = "input";
-	phy-supply = <&vcc_lan>;
+	phy-supply = <&vcc3v3_lan>;
 	phy-mode = "rgmii";
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
@@ -267,8 +291,8 @@
 				};
 			};
 
-			vcc1v8_codec: LDO_REG1 {
-				regulator-name = "vcc1v8_codec";
+			vcca1v8_codec: LDO_REG1 {
+				regulator-name = "vcca1v8_codec";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
@@ -278,8 +302,8 @@
 				};
 			};
 
-			vcc1v8_hdmi: LDO_REG2 {
-				regulator-name = "vcc1v8_hdmi";
+			vcca1v8_hdmi: LDO_REG2 {
+				regulator-name = "vcca1v8_hdmi";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
@@ -336,8 +360,8 @@
 				};
 			};
 
-			vcc0v9_hdmi: LDO_REG7 {
-				regulator-name = "vcc0v9_hdmi";
+			vcca0v9_hdmi: LDO_REG7 {
+				regulator-name = "vcca0v9_hdmi";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <900000>;
@@ -422,6 +446,20 @@
 	i2c-scl-rising-time-ns = <300>;
 	i2c-scl-falling-time-ns = <15>;
 	status = "okay";
+
+	es8316: codec@11 {
+		compatible = "everest,es8316";
+		reg = <0x11>;
+		clocks = <&cru SCLK_I2S_8CH_OUT>;
+		clock-names = "mclk";
+		#sound-dai-cells = <0>;
+
+		port {
+			es8316_p0_0: endpoint {
+				remote-endpoint = <&i2s0_p0_0>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -441,12 +479,19 @@
 	rockchip,capture-channels = <2>;
 	rockchip,playback-channels = <2>;
 	status = "okay";
+
+	i2s0_p0: port {
+		i2s0_p0_0: endpoint {
+			dai-format = "i2s";
+			mclk-fs = <256>;
+			remote-endpoint = <&es8316_p0_0>;
+		};
+	};
 };
 
 &i2s1 {
 	rockchip,playback-channels = <2>;
 	rockchip,capture-channels = <2>;
-	status = "okay";
 };
 
 &i2s2 {
@@ -457,7 +502,7 @@
 	status = "okay";
 
 	bt656-supply = <&vcc_3v0>;
-	audio-supply = <&vcc_3v0>;
+	audio-supply = <&vcca1v8_codec>;
 	sdmmc-supply = <&vcc_sdio>;
 	gpio1830-supply = <&vcc_3v0>;
 };
@@ -596,13 +641,22 @@
 };
 
 &sdhci {
+	max-frequency = <150000000>;
 	bus-width = <8>;
-	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
+	mmc-hs200-1_8v;
 	non-removable;
 	status = "okay";
 };
 
+&spdif {
+
+	spdif_p0: port {
+		spdif_p0_0: endpoint {
+			remote-endpoint = <&dit_p0_0>;
+		};
+	};
+};
+
 &tcphy0 {
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
@@ -574,7 +574,7 @@
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		clocks = <&rk808 1>;
-		clock-names = "ext_clock";
+		clock-names = "txco";
 		device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
 		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
 		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
@@ -163,7 +163,7 @@
 	status = "okay";
 
 	rt5651: rt5651@1a {
-		compatible = "rockchip,rt5651";
+		compatible = "realtek,rt5651";
 		reg = <0x1a>;
 		clocks = <&cru SCLK_I2S_8CH_OUT>;
 		clock-names = "mclk";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -993,7 +993,9 @@
 			power-domain@RK3399_PD_VDU {
 				reg = <RK3399_PD_VDU>;
 				clocks = <&cru ACLK_VDU>,
-					 <&cru HCLK_VDU>;
+					 <&cru HCLK_VDU>,
+					 <&cru SCLK_VDU_CA>,
+					 <&cru SCLK_VDU_CORE>;
 				pm_qos = <&qos_video_m1_r>,
 					 <&qos_video_m1_w>;
 				#power-domain-cells = <0>;
@@ -1260,7 +1262,7 @@
 
 	vdec: video-codec@ff660000 {
 		compatible = "rockchip,rk3399-vdec";
-		reg = <0x0 0xff660000 0x0 0x400>;
+		reg = <0x0 0xff660000 0x0 0x480>;
 		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH 0>;
 		clocks = <&cru ACLK_VDU>, <&cru HCLK_VDU>,
 			 <&cru SCLK_VDU_CA>, <&cru SCLK_VDU_CORE>;
@@ -1477,6 +1479,7 @@
 			reg = <0xf780 0x24>;
 			clocks = <&sdhci>;
 			clock-names = "emmcclk";
+			drive-impedance-ohm = <50>;
 			#phy-cells = <0>;
 			status = "disabled";
 		};
@@ -1487,7 +1490,6 @@
 			clock-names = "refclk";
 			#phy-cells = <1>;
 			resets = <&cru SRST_PCIEPHY>;
-			drive-impedance-ohm = <50>;
 			reset-names = "phy";
 			status = "disabled";
 		};
@@ -1799,21 +1801,25 @@
 	hdmi: hdmi@ff940000 {
 		compatible = "rockchip,rk3399-dw-hdmi";
 		reg = <0x0 0xff940000 0x0 0x20000>;
+		reg-io-width = <4>;
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH 0>;
 		clocks = <&cru PCLK_HDMI_CTRL>,
 			 <&cru SCLK_HDMI_SFR>,
-			 <&cru PLL_VPLL>,
+			 <&cru SCLK_HDMI_CEC>,
 			 <&cru PCLK_VIO_GRF>,
-			 <&cru SCLK_HDMI_CEC>;
-		clock-names = "iahb", "isfr", "vpll", "grf", "cec";
+			 <&cru PLL_VPLL>;
+		clock-names = "iahb", "isfr", "cec", "grf", "vpll";
 		power-domains = <&power RK3399_PD_HDCP>;
-		reg-io-width = <4>;
 		rockchip,grf = <&grf>;
 		#sound-dai-cells = <0>;
 		status = "disabled";
 
 		ports {
-			hdmi_in: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hdmi_in: port@0 {
+				reg = <0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -1826,6 +1832,10 @@
 					remote-endpoint = <&vopl_out_hdmi>;
 				};
 			};
+
+			hdmi_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
@@ -599,8 +599,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <0 134 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -701,8 +701,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <0 137 4>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
 			clock-names = "ref", "bus_early", "suspend";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
@@ -59,7 +59,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01840000 0x00 0xC0000>;	/* GICR */
+		      <0x00 0x01840000 0x00 0xC0000>,	/* GICR */
+		      <0x01 0x00000000 0x00 0x2000>,	/* GICC */
+		      <0x01 0x00010000 0x00 0x1000>,	/* GICH */
+		      <0x01 0x00020000 0x00 0x2000>;	/* GICV */
 		/*
 		 * vcpumntirq:
 		 * virtual CPU interface maintenance interrupt
@@ -453,13 +456,11 @@
 		clock-names = "clk_ahb", "clk_xin";
 		mmc-ddr-1_8v;
 		mmc-hs200-1_8v;
-		mmc-hs400-1_8v;
 		ti,trm-icp = <0x2>;
 		ti,otap-del-sel-legacy = <0x0>;
 		ti,otap-del-sel-mmc-hs = <0x0>;
 		ti,otap-del-sel-ddr52 = <0x6>;
 		ti,otap-del-sel-hs200 = <0x7>;
-		ti,otap-del-sel-hs400 = <0x4>;
 	};
 
 	sdhci1: mmc@fa00000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
@@ -10,7 +10,6 @@
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x04a00000 0x00 0x100>;
 		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
-		clock-frequency = <48000000>;
 		current-speed = <115200>;
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 149 0>;
@@ -21,7 +20,6 @@
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x04a10000 0x00 0x100>;
 		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
-		clock-frequency = <48000000>;
 		current-speed = <115200>;
 		power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 160 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-am64.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-am64.dtsi
@@ -85,6 +85,7 @@
 			 <0x00 0x68000000 0x00 0x68000000 0x00 0x08000000>, /* PCIe DAT0 */
 			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00200000>, /* OC SRAM */
 			 <0x00 0x78000000 0x00 0x78000000 0x00 0x00800000>, /* Main R5FSS */
+			 <0x01 0x00000000 0x01 0x00000000 0x00 0x00310000>, /* A53 PERIPHBASE */
 			 <0x06 0x00000000 0x06 0x00000000 0x01 0x00000000>, /* PCIe DAT1 */
 			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS0 DAT3 */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-am642.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-am642.dtsi
@@ -60,6 +60,6 @@
 		cache-level = <2>;
 		cache-size = <0x40000>;
 		cache-line-size = <64>;
-		cache-sets = <512>;
+		cache-sets = <256>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -35,7 +35,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01880000 0x00 0x90000>;	/* GICR */
+		      <0x00 0x01880000 0x00 0x90000>,	/* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,	/* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,	/* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;	/* GICV */
 		/*
 		 * vcpumntirq:
 		 * virtual CPU interface maintenance interrupt
@@ -117,7 +120,6 @@
 		dmas = <&main_udmap 0xc000>, <&main_udmap 0x4000>,
 				<&main_udmap 0x4001>;
 		dma-names = "tx", "rx1", "rx2";
-		dma-coherent;
 
 		rng: rng@4e10000 {
 			compatible = "inside-secure,safexcel-eip76";
@@ -853,7 +855,7 @@
 		assigned-clocks = <&k3_clks 67 2>;
 		assigned-clock-parents = <&k3_clks 67 5>;
 
-		interrupts = <GIC_SPI 166 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
 
 		dma-coherent;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-am65.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-am65.dtsi
@@ -84,6 +84,7 @@
 			 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
 			 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>,
 			 <0x00 0x50000000 0x00 0x50000000 0x00 0x8000000>,
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A53 PERIPHBASE */
 			 <0x00 0x70000000 0x00 0x70000000 0x00 0x200000>,
 			 <0x05 0x00000000 0x05 0x00000000 0x01 0x0000000>,
 			 <0x07 0x00000000 0x07 0x00000000 0x01 0x0000000>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -77,28 +77,28 @@
 	};
 };
 
-&wkup_pmx0 {
+&wkup_pmx2 {
 	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
-			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
-			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
-			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
-			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
-			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
-			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
-			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
-			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
-			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
-			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
 
 	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
-			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 		>;
 	};
 };
@@ -131,15 +131,17 @@
 		>;
 	};
 
-	main_usbss0_pins_default: main-usbss0-pins-default {
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 		pinctrl-single,pins = <
-			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
+			J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
 		>;
 	};
+};
 
-	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+&main_pmx1 {
+	main_usbss0_pins_default: main-usbss0-pins-default {
 		pinctrl-single,pins = <
-			J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+			J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
 		>;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -32,7 +32,7 @@
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00100000 0x1c000>;
 
-		serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "mmio-mux";
 			#mux-control-cells = <1>;
 			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
@@ -54,7 +54,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01900000 0x00 0x100000>;	/* GICR */
+		      <0x00 0x01900000 0x00 0x100000>,	/* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,	/* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,	/* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;	/* GICV */
 
 		/* vcpumntirq: virtual CPU interface maintenance interrupt */
 		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -292,7 +295,16 @@
 	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
-		reg = <0x00 0x11c000 0x00 0x2b4>;
+		reg = <0x00 0x11c000 0x00 0x10c>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	main_pmx1: pinctrl@11c11c {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x00 0x11c11c 0x00 0xc>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
 		pinctrl-single,function-mask = <0xffffffff>;
@@ -606,10 +618,10 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		cdns,no-bar-match-nbits = <64>;
-		vendor-id = /bits/ 16 <0x104c>;
-		device-id = /bits/ 16 <0xb00f>;
+		vendor-id = <0x104c>;
+		device-id = <0xb00f>;
 		msi-map = <0x0 &gic_its 0x0 0x10000>;
 		dma-coherent;
 		ranges = <0x01000000 0x0 0x18001000  0x00 0x18001000  0x0 0x0010000>,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -56,7 +56,34 @@
 	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
-		reg = <0x00 0x4301c000 0x00 0x178>;
+		reg = <0x00 0x4301c000 0x00 0x34>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	wkup_pmx1: pinctrl@0x4301c038 {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x00 0x4301c038 0x00 0x8>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	wkup_pmx2: pinctrl@0x4301c068 {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x00 0x4301c068 0x00 0xec>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	wkup_pmx3: pinctrl@0x4301c174 {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x00 0x4301c174 0x00 0x20>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
 		pinctrl-single,function-mask = <0xffffffff>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-j7200.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-j7200.dtsi
@@ -60,7 +60,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -74,7 +74,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 	};
@@ -84,7 +84,7 @@
 		cache-level = <2>;
 		cache-size = <0x100000>;
 		cache-line-size = <64>;
-		cache-sets = <2048>;
+		cache-sets = <1024>;
 		next-level-cache = <&msmc_l3>;
 	};
 
@@ -127,6 +127,7 @@
 			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
 			 <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
 			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00800000>, /* MSMC RAM */
 			 <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */
 			 <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT1 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -42,7 +42,7 @@
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x00100000 0x1c000>;
 
-		serdes_ln_ctrl: mux@4080 {
+		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "mmio-mux";
 			reg = <0x00004080 0x50>;
 			#mux-control-cells = <1>;
@@ -76,7 +76,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01900000 0x00 0x100000>;	/* GICR */
+		      <0x00 0x01900000 0x00 0x100000>,	/* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,	/* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,	/* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;	/* GICV */
 
 		/* vcpumntirq: virtual CPU interface maintenance interrupt */
 		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -333,7 +336,6 @@
 		dmas = <&main_udmap 0xc000>, <&main_udmap 0x4000>,
 				<&main_udmap 0x4001>;
 		dma-names = "tx", "rx1", "rx2";
-		dma-coherent;
 
 		rng: rng@4e10000 {
 			compatible = "inside-secure,safexcel-eip76";
@@ -610,7 +612,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x0 0x10000>;
@@ -636,7 +638,7 @@
 		clocks = <&k3_clks 239 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
@@ -658,7 +660,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x10000 0x10000>;
@@ -684,7 +686,7 @@
 		clocks = <&k3_clks 240 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
@@ -706,7 +708,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x20000 0x10000>;
@@ -732,7 +734,7 @@
 		clocks = <&k3_clks 241 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
@@ -754,7 +756,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x30000 0x10000>;
@@ -780,7 +782,7 @@
 		clocks = <&k3_clks 242 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -1049,7 +1051,6 @@
 		ti,itap-del-sel-mmc-hs = <0xa>;
 		ti,itap-del-sel-ddr52 = <0x3>;
 		ti,trm-icp = <0x8>;
-		ti,strobe-sel = <0x77>;
 		dma-coherent;
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -61,7 +61,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -75,7 +75,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 	};
@@ -85,7 +85,7 @@
 		cache-level = <2>;
 		cache-size = <0x100000>;
 		cache-line-size = <64>;
-		cache-sets = <2048>;
+		cache-sets = <1024>;
 		next-level-cache = <&msmc_l3>;
 	};
 
@@ -136,6 +136,7 @@
 			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x01800000>, /* PCIe Core*/
 			 <0x00 0x10000000 0x00 0x10000000 0x00 0x10000000>, /* PCIe DAT */
 			 <0x00 0x64800000 0x00 0x64800000 0x00 0x00800000>, /* C71 */
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
 			 <0x44 0x00000000 0x44 0x00000000 0x00 0x08000000>, /* PCIe2 DAT */
 			 <0x44 0x10000000 0x44 0x10000000 0x00 0x08000000>, /* PCIe3 DAT */
 			 <0x4d 0x80800000 0x4d 0x80800000 0x00 0x00800000>, /* C66_0 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/Makefile
@@ -2,7 +2,6 @@
 dtb-$(CONFIG_ARCH_ZYNQMP) += avnet-ultra96-rev1.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1232-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1254-revA.dtb
-dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1275-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm015-dc1.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm016-dc2.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm017-dc3.dtb
@@ -12,7 +11,94 @@
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.1.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-a2197-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-dlc21-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-e-a2197-00-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-g-a2197-00-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-m-a2197-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-m-a2197-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-m-a2197-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-p-a2197-00-revA-x-prc-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-p-a2197-00-revA-x-prc-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-p-a2197-00-revA-x-prc-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-p-a2197-00-revA-x-prc-04-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-p-a2197-00-revA-x-prc-05-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-p-a2197-00-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sc-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sc-vpk120-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sc-vpk180-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-vp-x-a2785-00-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-vpk120-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu670-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu670-revB.dtb
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sm-k26-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-smk-k26-revA.dtb
+
+sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo
+sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo
+smk-k26-revA-sck-kv-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo
+smk-k26-revA-sck-kv-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo
+
+sm-k26-revA-sck-kr-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kr-g-revA.dtbo
+sm-k26-revA-sck-kr-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kr-g-revB.dtbo
+smk-k26-revA-sck-kr-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kr-g-revA.dtbo
+smk-k26-revA-sck-kr-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kr-g-revB.dtbo
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sck-kv-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sck-kv-g-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kr-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kr-g-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sck-kr-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sck-kr-g-revB.dtb
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sm-k24-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-smk-k24-revA.dtb
+
+sm-k24-revA-sck-kd-g-revA-dtbs := zynqmp-sm-k24-revA.dtb zynqmp-sck-kd-g-revA.dtbo
+smk-k24-revA-sck-kd-g-revA-dtbs := zynqmp-smk-k24-revA.dtb zynqmp-sck-kd-g-revA.dtbo
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k24-revA-sck-kd-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k24-revA-sck-kd-g-revA.dtb
+
+# Versal boards
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-v350-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-01-revA-ospi.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-04-revA-ospi.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-04-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA-x-prc-05-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vc-p-a2197-00-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-rev1.1-x-ebm-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-rev1.1-x-ebm-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-rev1.1-x-ebm-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-rev1.1.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-revA-x-ebm-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-revA-x-ebm-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-revA-x-ebm-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck190-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vck5000-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-rev1.1-x-ebm-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-rev1.1-x-ebm-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-rev1.1-x-ebm-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-rev1.1.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-revA-x-ebm-01-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-revA-x-ebm-02-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-revA-x-ebm-03-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vmk180-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vp-x-a2785-00-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vpk120-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vpk120-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += versal-vpk180-revA.dtb
+
+# Make sure that symbols are compiled in for device trees that are not overlayed
+DTC_FLAGS += -@
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Avnet Ultra96 rev1
  *
- * (C) Copyright 2018, Xilinx, Inc.
+ * (C) Copyright 2018 - 2020, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-clk.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-clk.dtsi
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal with PM
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/power/xlnx-versal-power.h>
+#include <dt-bindings/clock/xlnx-versal-clk.h>
+
+/ {
+	pl_alt_ref_clk: pl_alt_ref_clk {
+		u-boot,dm-pre-reloc;
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33333333>;
+	};
+
+	ref_clk: ref_clk {
+		u-boot,dm-pre-reloc;
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33333333>;
+	};
+
+	can0_clk: can0_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&versal_clk CAN0_REF>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	can1_clk: can1_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&versal_clk CAN1_REF>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	firmware {
+		versal_firmware: versal-firmware {
+			compatible = "xlnx,versal-firmware";
+			interrupt-parent = <&gic>;
+			u-boot,dm-pre-reloc;
+			method = "smc";
+			#power-domain-cells = <1>;
+
+			versal_clk: clock-controller {
+				u-boot,dm-pre-reloc;
+				#clock-cells = <1>;
+				compatible = "xlnx,versal-clk";
+				clocks = <&ref_clk>, <&pl_alt_ref_clk>;
+				clock-names = "ref_clk", "pl_alt_ref_clk";
+			};
+
+			zynqmp_power: zynqmp-power {
+				compatible = "xlnx,zynqmp-power";
+				interrupt-parent = <&gic>;
+				interrupts = <0 30 4>;
+				mboxes = <&ipi_mailbox_pmu1 0>,
+					 <&ipi_mailbox_pmu1 1>;
+				mbox-names = "tx", "rx";
+			};
+
+			versal_sec_cfg: versal-sec-cfg {
+				compatible = "xlnx,versal-sec-cfg";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				bbram_zeroize: bbram-zeroize@4 {
+					reg = <0x04 0x4>;
+				};
+
+				bbram_key: bbram-key@10 {
+					reg = <0x10 0x20>;
+				};
+
+				bbram_usr: bbram-usr@30 {
+					reg = <0x30 0x4>;
+				};
+
+				bbram_lock: bbram-lock@48 {
+					reg = <0x48 0x4>;
+				};
+
+				user_key0: user-key@110 {
+					reg = <0x110 0x20>;
+				};
+
+				user_key1: user-key@130 {
+					reg = <0x130 0x20>;
+				};
+
+				user_key2: user-key@150 {
+					reg = <0x150 0x20>;
+				};
+
+				user_key3: user-key@170 {
+					reg = <0x170 0x20>;
+				};
+
+				user_key4: user-key@190 {
+					reg = <0x190 0x20>;
+				};
+
+				user_key5: user-key@1b0 {
+					reg = <0x1b0 0x20>;
+				};
+
+				user_key6: user-key@1d0 {
+					reg = <0x1d0 0x20>;
+				};
+
+				user_key7: user-key@1f0 {
+					reg = <0x1f0 0x20>;
+				};
+			};
+		};
+	};
+
+	zynqmp_ipi {
+		compatible = "xlnx,zynqmp-ipi-mailbox";
+		interrupt-parent = <&gic>;
+		interrupts = <0 30 4>;
+		xlnx,ipi-id = <2>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipi_mailbox_pmu1: mailbox@ff3f0440 {
+			reg = <0 0xff3f0440 0 0x20>,
+			      <0 0xff3f0460 0 0x20>,
+			      <0 0xff3f0280 0 0x20>,
+			      <0 0xff3f02a0 0 0x20>;
+			reg-names = "local_request_region", "local_response_region",
+				    "remote_request_region", "remote_response_region";
+			#mbox-cells = <1>;
+			xlnx,ipi-id = <1>;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&versal_clk ACPU>;
+};
+
+&can0 {
+	clocks = <&can0_clk>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_CAN_FD_0>;
+};
+
+&can1 {
+	clocks = <&can1_clk>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_CAN_FD_1>;
+};
+
+&gem0 {
+	clocks = <&versal_clk LPD_LSBUS>,
+		 <&versal_clk GEM0_REF>, <&versal_clk GEM0_TX>,
+		 <&versal_clk GEM0_RX>, <&versal_clk GEM_TSU>;
+	power-domains = <&versal_firmware PM_DEV_GEM_0>;
+};
+
+&gem1 {
+	clocks = <&versal_clk LPD_LSBUS>,
+		 <&versal_clk GEM1_REF>, <&versal_clk GEM1_TX>,
+		 <&versal_clk GEM1_RX>, <&versal_clk GEM_TSU>;
+	power-domains = <&versal_firmware PM_DEV_GEM_1>;
+};
+
+&gpio0 {
+	clocks = <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_GPIO>;
+};
+
+&gpio1 {
+	clocks = <&versal_clk PMC_LSBUS_REF>;
+	power-domains = <&versal_firmware PM_DEV_GPIO_PMC>;
+};
+
+&i2c0 {
+	clocks = <&versal_clk I2C0_REF>;
+	power-domains = <&versal_firmware PM_DEV_I2C_0>;
+};
+
+&i2c1 {
+	clocks = <&versal_clk I2C1_REF>;
+	power-domains = <&versal_firmware PM_DEV_I2C_1>;
+};
+
+&i2c2 {
+	clocks = <&versal_clk I2C_REF>;
+	power-domains = <&versal_firmware PM_DEV_I2C_PMC>;
+};
+
+&lpd_dma_chan0 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_0>;
+};
+
+&lpd_dma_chan1 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_1>;
+};
+
+&lpd_dma_chan2 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_2>;
+};
+
+&lpd_dma_chan3 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_3>;
+};
+
+&lpd_dma_chan4 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_4>;
+};
+
+&lpd_dma_chan5 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_5>;
+};
+
+&lpd_dma_chan6 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_6>;
+};
+
+&lpd_dma_chan7 {
+	clocks = <&versal_clk ADMA>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_ADMA_7>;
+};
+
+&qspi {
+	clocks = <&versal_clk QSPI_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_QSPI>;
+};
+
+&ospi {
+	clocks = <&versal_clk OSPI_REF>;
+	power-domains = <&versal_firmware PM_DEV_OSPI>;
+};
+
+&rtc {
+	power-domains = <&versal_firmware PM_DEV_RTC>;
+};
+
+&serial0 {
+	clocks = <&versal_clk UART0_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_UART_0>;
+};
+
+&serial1 {
+	clocks = <&versal_clk UART1_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_UART_1>;
+};
+
+&sdhci0 {
+	clocks = <&versal_clk SDIO0_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_SDIO_0>;
+};
+
+&sdhci1 {
+	clocks = <&versal_clk SDIO1_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_SDIO_1>;
+};
+
+&spi0 {
+	clocks = <&versal_clk SPI0_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_SPI_0>;
+};
+
+&spi1 {
+	clocks = <&versal_clk SPI1_REF>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_SPI_1>;
+};
+
+&ttc0 {
+	clocks = <&versal_clk TTC0>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_TTC_0>;
+};
+
+&ttc1 {
+	clocks = <&versal_clk TTC1>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_TTC_1>;
+};
+
+&ttc2 {
+	clocks = <&versal_clk TTC2>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_TTC_2>;
+};
+
+&ttc3 {
+	clocks = <&versal_clk TTC3>, <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_TTC_3>;
+};
+
+&usb0 {
+	clocks = <&versal_clk USB0_BUS_REF>, <&versal_clk USB3_DUAL_REF>;
+	power-domains = <&versal_firmware PM_DEV_USB_0>;
+};
+
+&watchdog {
+	clocks = <&versal_clk LPD_LSBUS>;
+	power-domains = <&versal_firmware PM_DEV_SWDT_FPD>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-v350-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-v350-revA.dts
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal v350 revA
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "xlnx,versal-v350-revA", "xlnx,versal";
+	model = "Xilinx Versal v350 board revA";
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF010000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		spi0 = &ospi;
+	};
+
+	memory: memory@0 {
+		device_type = "memory"; /* 16GB total via MC0/1/2/3 */
+		reg = <0 0 0 0x80000000>; /* 2GB here */
+		/* <0x8 0x0 0x3 0x80000000> */ /* 12GB - enable it later */
+	};
+};
+
+&ospi {
+	status = "okay";
+	bus-num = <2>;
+	num-cs = <1>;
+	#stream-id-cells = <1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reset-gpios = <&gpio1 0xc GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "mt35xu02g", "micron,m25p80", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		cdns,read-delay = <0x0>;
+		cdns,tshsl-ns = <0x0>;
+		cdns,tsd2d-ns = <0x0>;
+		cdns,tchsh-ns = <0x1>;
+		cdns,tslch-ns = <0x1>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <20000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "disabled"; /* communication with MSP432 */
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-01-revA-ospi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-01-revA-ospi.dts
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-01 revA (SE1)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA-x-prc-01-revA.dts"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA-x-prc-01-revA",
+		     "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA - x-prc-01 revA OSPI";
+
+	aliases {
+		spi0 = &ospi;
+	};
+};
+
+/* Mutually exclusive */
+&ospi {
+	status = "okay"; /* U97 MT35XU02G */
+	bus-num = <2>;
+	num-cs = <1>;
+	#stream-id-cells = <1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reset-gpios = <&gpio1 0xc GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "mt35xu02g", "micron,m25p80", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		cdns,read-delay = <0x0>;
+		cdns,tshsl-ns = <0x0>;
+		cdns,tsd2d-ns = <0x0>;
+		cdns,tchsh-ns = <0x1>;
+		cdns,tslch-ns = <0x1>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <20000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&qspi {
+	status = "disabled";
+};
+
+&lpd_dma_chan0 {
+	status = "okay";
+};
+
+&lpd_dma_chan1 {
+	status = "okay";
+};
+
+&lpd_dma_chan2 {
+	status = "okay";
+};
+
+&lpd_dma_chan3 {
+	status = "okay";
+};
+
+&lpd_dma_chan4 {
+	status = "okay";
+};
+
+&lpd_dma_chan5 {
+	status = "okay";
+};
+
+&lpd_dma_chan6 {
+	status = "okay";
+};
+
+&lpd_dma_chan7 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-01-revA.dts
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-01 revA (SE1)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA-x-prc-01-revA",
+		     "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA - x-prc-01 revA QSPI";
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		ethernet1 = &gem1;
+		i2c0 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		rtc0 = &rtc;
+	};
+};
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay"; /* u93 and u92 */
+	num-cs = <0x1>;
+	is-dual = <0x1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <4>;
+
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <35000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&sdhci1 { /* U104 */
+	status = "okay";
+	xlnx,mio-bank = <1>;
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy1>; /* u128 */
+	phy-mode = "rgmii-id";
+	phy1: phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk; /* FIXME - Remove if board is fixed */
+	};
+	phy2: phy@2 {
+		reg = <2>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk; /* FIXME - Remove if board is fixed */
+	};
+};
+
+&gem1 {
+	status = "okay";
+	phy-handle = <&phy2>; /* u134 */
+	phy-mode = "rgmii-id";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	eeprom_versal: eeprom@51 { /* U116 */
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	/* FIXME - U117 and U118 */
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0x0>;
+	xlnx,usb-reset-mode = <0x0>;
+};
+
+&dwc3_0 { /* USB 2.0 host - U99 */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+};
+
+&lpd_dma_chan0 {
+	status = "okay";
+};
+
+&lpd_dma_chan1 {
+	status = "okay";
+};
+
+&lpd_dma_chan2 {
+	status = "okay";
+};
+
+&lpd_dma_chan3 {
+	status = "okay";
+};
+
+&lpd_dma_chan4 {
+	status = "okay";
+};
+
+&lpd_dma_chan5 {
+	status = "okay";
+};
+
+&lpd_dma_chan6 {
+	status = "okay";
+};
+
+&lpd_dma_chan7 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-02-revA.dts
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-02 revA (SE2)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA-x-prc-02-revA",
+		     "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA - x-prc-02 revA";
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		i2c0 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		usb0 = &usb0;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>; /* u9 */
+	phy-mode = "rgmii-id";
+	phy0: phy@1 { /* Marvell 88E1512; U9 */
+		reg = <1>;
+	};
+};
+
+&sdhci0 {
+	status = "okay";
+	xlnx,mio-bank = <1>;
+};
+
+&sdhci1 { /* U1A */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 { /* U4 */
+	status = "okay";
+	dr_mode = "peripheral";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	maximum-speed = "high-speed";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	/* U12 Catalyst EEPROM - AT24 should be equivalent */
+	eeprom_versal: eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	/* FIXME - U13 and U15 */
+};
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 { /* U18 */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf016b", "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x200000>;
+		};
+	};
+};
+
+&spi1 {
+	status = "okay";
+	num-cs = <3>;	/* FIXME - check SPI1_SS0-2_B */
+
+	flash@0 { /* U19 */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst26vf016b", "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "spi1-flash0";
+			reg = <0x0 0x200000>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-03-revA.dts
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-03 revA (SE3)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA-x-prc-03-revA",
+		     "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA - x-prc-03 revA";
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		can0 = &can0;
+		can1 = &can1;
+		i2c0 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		serial0 = &serial0;
+		spi0 = &qspi;
+		spi1 = &spi0;
+	};
+};
+
+/* SMAP via cc108 */
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	/* Must be enabled via J90/J91 */
+	eeprom_versal: eeprom@51 { /* U2 - 128kb RM24C128DS */
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+};
+
+&qspi {
+	status = "okay"; /* u7 */
+	num-cs = <0x1>;
+	is-dual = <0x1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <1>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80", "jedec,spi-nor"; /* 64Mb */
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x800000>;
+		};
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&sdhci0 { /* J99 MIO28 - MIO33 */
+	status = "okay";
+	xlnx,mio-bank = <1>; /* FIXME */
+};
+
+&sdhci1 { /* EMMC IS21ES08G 200MHz MIO40 - MIO49 */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>; /* FIXME */
+};
+
+&spi0 {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 { /* U6 - IS25LQ032B - 16Mb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "issi,is25lq032b", "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0 0x200000>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-04-revA-ospi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-04-revA-ospi.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-04 revA (SE4)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA-x-prc-04-revA.dts"
+
+/ {
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		spi0 = &ospi;
+	};
+};
+
+/* Mutually exclusive with qspi */
+&ospi {
+	status = "okay"; /* U163/U97 MT35XU02G */
+};
+
+&qspi {
+	status = "disabled";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-04-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-04-revA.dts
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-04 revA (SE4)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA-x-prc-04-revA",
+		     "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA - x-prc-04 revA";
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet1 = &gem1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		spi1 = &spi0;
+		usb0 = &usb0;
+	};
+};
+
+&gem1 {
+	status = "okay";
+	phy-handle = <&phy1>; /* u175 */
+	phy-mode = "rgmii-id"; /* RTL8211DN */
+	phy1: phy@1 {
+		reg = <2>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	eeprom_versal: eeprom@51 { /* U153 */
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x51>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	eeprom: eeprom@51 { /* U155 */
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x51>;
+	};
+};
+
+&qspi {
+	status = "okay"; /* u93 and u92 and u161 and u160 */
+	num-cs = <1>;
+	is-dual = <0>;
+	is-stacked = <1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <4>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80", "jedec,spi-nor"; /* 512MB */
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x20000000>;
+		};
+	};
+};
+
+&sdhci1 { /* J3 MIO26, MIO29 - MIO33 */
+	status = "okay";
+	disable-wp;
+	xlnx,mio-bank = <1>; /* FIXME */
+};
+
+&serial0 { /* MIO35 - MIO37 */
+	status = "okay";
+};
+
+&serial1 { /* MIO4 - MIO7 RS232 */
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 { /* U171 - IS25LP016B - 16Mb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "issi,is25lp016b", "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0 0x200000>;
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0x0>;
+	xlnx,usb-reset-mode = <0x0>;
+};
+
+&dwc3_0 { /* USB 2.0 host - U99 */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-05-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA-x-prc-05-revA.dts
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal X-PRC-05 revA (SE5)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vc-p-a2197-00-revA.dts"
+#include <dt-bindings/net/mscc-phy-vsc8531.h>
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA-x-prc-05-revA",
+		     "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA - x-prc-05 revA";
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		ethernet1 = &gem1;
+		i2c0 = &i2c0;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	phy1: phy@1 { /* 88e1510 */
+		reg = <1>;
+	};
+	phy2: phy@2 { /* VSC8531 */
+		reg = <2>;
+		vsc8531,rx-delay = <VSC8531_RGMII_CLK_DELAY_2_6_NS>;
+		vsc8531,tx-delay = <VSC8531_RGMII_CLK_DELAY_2_6_NS>;
+	};
+};
+
+&gem1 {
+	status = "okay";
+	phy-handle = <&phy2>;
+	phy-mode = "rgmii-id";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	eeprom_versal: eeprom@51 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x51>;
+	};
+};
+
+&qspi {
+	status = "okay";
+	num-cs = <0x1>;
+	spi-tx-bus-width = <1>;
+	spi-rx-bus-width = <4>;
+
+	flash@0 { /* MX25U12835 128Mbit */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80", "jedec,spi-nor"; /* 16MB */
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <104000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x1000000>;
+		};
+	};
+};
+
+&sdhci0 { /* emmc0 */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>; /* FIXME */
+};
+
+&sdhci1 { /* connector */
+	status = "okay";
+	xlnx,mio-bank = <1>; /* FIXME */
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 { /* USB 2.0 host */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vc-p-a2197-00-revA.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+
+/ {
+	compatible = "xlnx,versal-vc-p-a2197-00-revA",
+		     "xlnx,versal-vc-p-a2197-00",
+		     "xlnx,versal-vc-p-a2197", "xlnx,versal";
+	model = "Xilinx Versal A2197 Processor board revA";
+
+	memory: memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x1 0x80000000>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdhci0 {
+	no-1-8-v;
+};
+
+&sdhci1 {
+	no-1-8-v;
+};
+
+&watchdog {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1-x-ebm-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1-x-ebm-01-revA.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 rev1.1 with X-EBM-01-revA module
+ *
+ * (C) Copyright 2019 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1-x-ebm-01-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-rev1.1-x-ebm-01-revA",
+		     "xlnx,versal-vck190-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board rev1.1 (QSPI)";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1-x-ebm-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1-x-ebm-02-revA.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 rev1.1 with X-EBM-02-revA module
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1-x-ebm-02-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-rev1.1-x-ebm-02-revA",
+		     "xlnx,versal-vck190-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board rev1.1 (EMMC)";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1-x-ebm-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1-x-ebm-03-revA.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 rev1.1 with X-EBM-03-revA module
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1-x-ebm-03-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-rev1.1-x-ebm-03-revA",
+		     "xlnx,versal-vck190-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board rev1.1 (OSPI)";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-rev1.1.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 rev1.1
+ *
+ * (C) Copyright 2019 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board rev1.1";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-revA-x-ebm-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-revA-x-ebm-01-revA.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 revA with X-EBM-01-revA module
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA-x-ebm-01-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-revA-x-ebm-01-revA",
+		     "xlnx,versal-vck190-revA", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board revA (QSPI)";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-revA-x-ebm-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-revA-x-ebm-02-revA.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 revA with X-EBM-02-revA module
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA-x-ebm-02-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-revA-x-ebm-02-revA",
+		     "xlnx,versal-vck190-revA", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board revA (EMMC)";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-revA-x-ebm-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-revA-x-ebm-03-revA.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 revA with X-EBM-03-revA module
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA-x-ebm-03-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-revA-x-ebm-03-revA",
+		     "xlnx,versal-vck190-revA", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board revA (OSPI)";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck190-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck190-revA.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck190 revA
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vck190-revA", "xlnx,versal";
+	model = "Xilinx Versal vck190 Eval board revA";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vck5000-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vck5000-revA.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vck5000 revA
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "xlnx,versal-vck5000-revA", "xlnx,versal";
+	model = "Xilinx Versal vck5000 board revA";
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		spi0 = &ospi;
+	};
+
+	memory: memory@0 {
+		device_type = "memory"; /* 16GB total via MC0/1/2/3 */
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x3 0x80000000>;
+	};
+};
+
+&ospi {
+	status = "okay";
+	bus-num = <2>;
+	num-cs = <1>;
+	#stream-id-cells = <1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reset-gpios = <&gpio1 0xc GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "mt35xu02g", "micron,m25p80", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		cdns,read-delay = <0x0>;
+		cdns,tshsl-ns = <0x0>;
+		cdns,tsd2d-ns = <0x0>;
+		cdns,tchsh-ns = <0x1>;
+		cdns,tslch-ns = <0x1>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <20000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x10000000>;
+		};
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "disabled"; /* communication with MSP432 */
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1-x-ebm-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1-x-ebm-01-revA.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 rev1.1 with X-EBM-01-revA module
+ *
+ * (C) Copyright 2019 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-rev1.1-x-ebm-01-revA",
+		     "xlnx,versal-vmk180-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board rev1.1 (QSPI)";
+};
+
+&qspi {
+#include "versal-x-ebm-01-revA.dtsi"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1-x-ebm-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1-x-ebm-02-revA.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 rev1.1 with X-EBM-02-revA module
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-rev1.1-x-ebm-02-revA",
+		     "xlnx,versal-vmk180-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board rev1.1 (EMMC)";
+};
+
+&sdhci1 {
+#include "versal-x-ebm-02-revA.dtsi"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1-x-ebm-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1-x-ebm-03-revA.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 rev1.1 with X-EBM-03-revA module
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-rev1.1.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-rev1.1-x-ebm-03-revA",
+		     "xlnx,versal-vmk180-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board rev1.1 (OSPI)";
+};
+
+&ospi {
+#include "versal-x-ebm-03-revA.dtsi"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-rev1.1.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 rev1.1
+ *
+ * (C) Copyright 2019 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-rev1.1", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board rev1.1";
+};
+
+&sdhci1 { /* PMC_MIO26-36/51 */
+	clk-phase-sd-hs = <111>, <48>;
+	clk-phase-uhs-sdr25 = <114>, <48>;
+	clk-phase-uhs-ddr50 = <126>, <36>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-revA-x-ebm-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-revA-x-ebm-01-revA.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 revA with X-EBM-01-revA module
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-revA-x-ebm-01-revA",
+		     "xlnx,versal-vmk180-revA", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board revA (QSPI)";
+};
+
+&qspi {
+#include "versal-x-ebm-01-revA.dtsi"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-revA-x-ebm-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-revA-x-ebm-02-revA.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 revA with X-EBM-02-revA module
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-revA-x-ebm-02-revA",
+		     "xlnx,versal-vmk180-revA", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board revA (EMMC)";
+};
+
+&sdhci1 {
+#include "versal-x-ebm-02-revA.dtsi"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-revA-x-ebm-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-revA-x-ebm-03-revA.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 revA with X-EBM-03-revA module
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal-vmk180-revA.dts"
+
+/ {
+	compatible = "xlnx,versal-vmk180-revA-x-ebm-03-revA",
+		     "xlnx,versal-vmk180-revA", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board revA (OSPI)";
+
+	aliases {
+		spi0 = &ospi;
+	};
+};
+
+&ospi {
+#include "versal-x-ebm-03-revA.dtsi"
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vmk180-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vmk180-revA.dts
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vmk180 revA
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+
+/ {
+	compatible = "xlnx,versal-vmk180-revA", "xlnx,versal";
+	model = "Xilinx Versal vmk180 Eval board revA";
+
+	memory: memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x1 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		ethernet1 = &gem1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		rtc0 = &rtc;
+	};
+};
+
+/* PMC_MIO 0 -12 - configuration header QSPI/OSPI/EMMC */
+/* FIXME PMC_MIO37 ZU4_TRIGGER/PMC_MIO37/38 PCIE */
+
+&can1 { /* MIO40-41 */
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&sdhci1 { /* PMC_MIO26-36/51 */
+	status = "okay";
+	xlnx,mio-bank = <1>;
+	no-1-8-v;
+};
+
+&serial0 { /* PMC_MIO42/43 */
+	status = "okay";
+};
+
+&gem0 { /* PMC_MIO_48, LPD_MIO0-11/24/25 */
+	status = "okay";
+	phy-handle = <&phy1>; /* u128 */
+	phy-mode = "rgmii-id";
+	phy1: phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+	phy2: phy@2 {
+		reg = <2>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&gem1 { /* PMC_MIO_49, LPD_MIO12-23 */
+	status = "okay";
+	phy-handle = <&phy2>; /* u134 */
+	phy-mode = "rgmii-id";
+};
+
+&i2c0 { /* PMC_MIO46/47 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&i2c1 { /* PMC_MIO44/45 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&usb0 { /* PMC_MIO13_500 - PMC_MIO25 USB 2.0 */
+	status = "okay";
+	xlnx,usb-polarity = <0x0>;
+	xlnx,usb-reset-mode = <0x0>;
+};
+
+&dwc3_0 { /* USB 2.0 host */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vp-x-a2785-00-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vp-x-a2785-00-revA.dts
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vp-x-a2785-00 revA
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+
+/ {
+	model = "Xilinx Versal vp-x-a2785-00 Eval board revA";
+	compatible = "xlnx,versal-vp-x-a2785-00-revA",
+		     "xlnx,versal-vp-x-a2785-00", "xlnx,versal";
+
+	memory: memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x1 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		rtc0 = &rtc;
+	};
+	/* Missing any LED for heartbeat */
+};
+
+&qspi { /* PMC_MIO_500 0 - 12 */
+	status = "okay"; /* u93 and u92 */
+	num-cs = <1>;
+	is-dual = <1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <4>;
+
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <35000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&usb0 { /* PMC_MIO_500 13 - 25 USB 2.0 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 { /* USB 2.0 host */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed"; /* FIXME */
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+};
+
+&sdhci1 { /* PMC_MIO_501 26 - 36/51 */
+	status = "okay";
+	xlnx,mio-bank = <1>;
+	no-1-8-v;
+};
+
+/* PWM via MIO 41/FAN TACH MIO 49 - FIXME */
+
+&serial0 { /* PMC_MIO42/43 */
+	status = "okay";
+};
+
+&i2c0 { /* PMC_MIO46/47 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&i2c1 { /* PMC_MIO44/45 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+/* PCIe at MIO 38/39/40/50 */
+
+&gem0 { /* PMC_MIO_48 - reset, LPD_MIO0-11 , mdio LPD_MIO24/25 */
+	status = "okay";
+	phy-handle = <&phy1>; /* u198 */
+	phy-mode = "rgmii-id";
+	phy1: phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+/* LPD_MIO12-23 - PM */
+
+&can1 { /* MIO40-41 */
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&gpio1 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&watchdog {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vpk120-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vpk120-revA.dts
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vpk120 revA
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+
+/ {
+	model = "Xilinx Versal vpk120 Eval board revA";
+	compatible = "xlnx,versal-vpk120-revA", "xlnx,versal-vpk120",
+		     "xlnx,versal";
+
+	memory: memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x2 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		rtc0 = &rtc;
+	};
+	/* Missing any LED for heartbeat */
+};
+
+&qspi { /* PMC_MIO_500 0 - 12 */
+	status = "okay"; /* u93 and u92 */
+	num-cs = <1>;
+	is-dual = <1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <4>;
+
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <35000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&usb0 { /* PMC_MIO_500 13 - 25 USB 2.0 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 { /* USB 2.0 host */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed"; /* FIXME */
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+};
+
+&sdhci1 { /* PMC_MIO_501 26 - 36/51 */
+	status = "okay";
+	xlnx,mio-bank = <1>;
+	no-1-8-v;
+};
+
+/* PWM via MIO 41/FAN TACH MIO 49 - FIXME */
+
+&serial0 { /* PMC_MIO42/43 */
+	status = "okay";
+};
+
+&i2c0 { /* PMC_MIO46/47 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&i2c1 { /* PMC_MIO44/45 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+/* PCIe at MIO 38/39/40/50 */
+
+&gem0 { /* PMC_MIO_48 - reset, LPD_MIO0-11 , mdio LPD_MIO24/25 */
+	status = "okay";
+	phy-handle = <&phy1>; /* u198 */
+	phy-mode = "rgmii-id";
+	phy1: phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+/* LPD_MIO12-23 - PM */
+
+&can1 { /* MIO40-41 */
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&gpio1 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&watchdog {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vpk120-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vpk120-revB.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vpk120 revB
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+
+/ {
+	model = "Xilinx Versal vpk120 Eval board revB";
+	compatible = "xlnx,versal-vpk120-revB", "xlnx,versal-vpk120",
+		     "xlnx,versal";
+
+	memory: memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x2 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		rtc0 = &rtc;
+	};
+	/* Missing any LED for heartbeat */
+};
+
+&qspi { /* PMC_MIO_500 0 - 12 */
+	status = "okay"; /* u93 and u92 */
+	num-cs = <1>;
+	is-dual = <1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <4>;
+
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <35000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&usb0 { /* PMC_MIO_500 13 - 25 USB 2.0 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 { /* USB 2.0 host */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed"; /* FIXME */
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+};
+
+&sdhci1 { /* PMC_MIO_501 26 - 36/51 */
+	status = "okay";
+	xlnx,mio-bank = <1>;
+	no-1-8-v;
+	clk-phase-sd-hs = <111>, <48>;
+	clk-phase-uhs-sdr25 = <114>, <48>;
+	clk-phase-uhs-ddr50 = <126>, <36>;
+};
+
+/* PWM via MIO 41/FAN TACH MIO 49 - FIXME */
+
+&serial0 { /* PMC_MIO42/43 */
+	status = "okay";
+};
+
+&i2c0 { /* PMC_MIO46/47 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&i2c1 { /* PMC_MIO44/45 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Use for storing information about board */
+	eeprom: eeprom@54 { /* u34 - m24128 16kB */
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x54>; /* & 0x5c */
+		u-boot,dm-pre-reloc;
+	};
+};
+
+/* PCIe at MIO 38/39/40/50 */
+
+&gem0 { /* PMC_MIO_48 - reset, LPD_MIO0-11 , mdio LPD_MIO24/25 */
+	status = "okay";
+	phy-handle = <&phy1>; /* u198 */
+	phy-mode = "rgmii-id";
+	phy1: phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+/* LPD_MIO12-23 - PM */
+
+&can1 { /* MIO40-41 */
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&gpio1 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&watchdog {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-vpk180-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-vpk180-revA.dts
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal vpk180 revA
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "versal.dtsi"
+#include "versal-clk.dtsi"
+
+/ {
+	model = "Xilinx Versal vpk180 Eval board revA";
+	compatible = "xlnx,versal-vpk180-revA", "xlnx,versal-vpk180",
+		     "xlnx,versal";
+
+	memory: memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x2 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0 earlycon=pl011,mmio32,0xFF000000,115200n8 clk_ignore_unused";
+		stdout-path = "serial0:115200";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		rtc0 = &rtc;
+	};
+	/* Missing any LED for heartbeat */
+};
+
+&qspi { /* PMC_MIO_500 0 - 12 */
+	status = "okay"; /* u93 and u92 */
+	num-cs = <1>;
+	is-dual = <1>;
+	spi-rx-bus-width = <4>;
+	spi-tx-bus-width = <4>;
+
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <35000000>;
+		partition@0 {
+			label = "spi0-flash0";
+			reg = <0x0 0x8000000>;
+		};
+	};
+};
+
+&usb0 { /* PMC_MIO_500 13 - 25 USB 2.0 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 { /* USB 2.0 host */
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "high-speed"; /* FIXME */
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb3_lpm_capable;
+};
+
+&sdhci1 { /* PMC_MIO_501 26 - 36/51 */
+	status = "okay";
+	xlnx,mio-bank = <1>;
+	no-1-8-v;
+	clk-phase-sd-hs = <111>, <48>;
+	clk-phase-uhs-sdr25 = <114>, <48>;
+	clk-phase-uhs-ddr50 = <126>, <36>;
+};
+
+&serial0 { /* PMC_MIO42/43 */
+	status = "okay";
+};
+
+&i2c0 { /* PMC_MIO46/47 */
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&i2c1 { /* PMC_MIO44/45 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Use for storing information about board */
+	eeprom: eeprom@54 { /* u34 - m24128 16kB */
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x54>; /* & 0x5c */
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&gem0 { /* PMC_MIO_48 - reset, LPD_MIO0-11 , mdio LPD_MIO24/25 */
+	status = "okay";
+	phy-handle = <&phy1>; /* u198 */
+	phy-mode = "rgmii-id";
+	phy1: phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <0xb>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&gpio1 {
+	status = "okay";
+	/* FIXME Fill names when versal starts */
+};
+
+&watchdog {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-x-ebm-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-x-ebm-01-revA.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx X-EBM-01 revA for vck190/vmk180
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,versal-x-ebm-01-revA", "xlnx,versal-x-ebm-01";
+
+	fragment {
+		target = <&qspi>;
+
+		__overlay__ {
+#include "versal-x-ebm-01-revA.dtsi"
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-x-ebm-01-revA.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-x-ebm-01-revA.dtsi
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx X-EBM-01 revA for vck190/vmk180
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+status = "okay";
+num-cs = <1>;
+spi-tx-bus-width = <1>;
+spi-rx-bus-width = <4>;
+#address-cells = <1>;
+#size-cells = <0>;
+is-dual = <1>;
+flash@0 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "m25p80", "jedec,spi-nor"; /* 256MB */
+	reg = <0>;
+	spi-tx-bus-width = <4>;
+	spi-rx-bus-width = <4>;
+	spi-max-frequency = <150000000>;
+	partition@0 {
+		label = "spi0-flash0";
+		reg = <0x0 0x10000000>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-x-ebm-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-x-ebm-02-revA.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx X-EBM-02 revA for vck190/vmk180
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,versal-x-ebm-02-revA", "xlnx,versal-x-ebm-02";
+
+	fragment {
+		target = <&sdhci1>;
+
+		__overlay__ {
+#include "versal-x-ebm-02-revA.dtsi"
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-x-ebm-02-revA.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-x-ebm-02-revA.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx X-EBM-02 revA for vck190/vmk180
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/* emmc MIO 0-13 - MTFC8GAKAJCN */
+status = "okay";
+non-removable;
+disable-wp;
+bus-width = <8>;
+xlnx,mio-bank = <0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-x-ebm-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-x-ebm-03-revA.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx X-EBM-03 revA for vck190/vmk180
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,versal-x-ebm-03-revA", "xlnx,versal-x-ebm-03";
+
+	fragment {
+		target = <&ospi>;
+
+		__overlay__ {
+#include "versal-x-ebm-03-revA.dtsi"
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal-x-ebm-03-revA.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal-x-ebm-03-revA.dtsi
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx X-EBM-03 revA for vck190/vmk180
+ *
+ * (C) Copyright 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/* U97 MT35XU02G */
+status = "okay";
+compatible = "xlnx,versal-ospi-1.0", "cadence,qspi", "cdns,qspi-nor";
+bus-num = <2>;
+num-cs = <1>;
+#stream-id-cells = <1>;
+#address-cells = <1>;
+#size-cells = <0>;
+reset-gpios = <&gpio1 0xc GPIO_ACTIVE_HIGH>;
+
+flash@0 {
+	compatible = "mt35xu02g", "micron,m25p80", "jedec,spi-nor";
+	reg = <0>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	cdns,read-delay = <0x0>;
+	cdns,tshsl-ns = <0x0>;
+	cdns,tsd2d-ns = <0x0>;
+	cdns,tchsh-ns = <0x1>;
+	cdns,tslch-ns = <0x1>;
+	spi-tx-bus-width = <8>;
+	spi-rx-bus-width = <8>;
+	spi-max-frequency = <20000000>;
+	partition@0 {
+		label = "spi0-flash0";
+		reg = <0x0 0x8000000>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/versal.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/versal.dtsi
@@ -0,0 +1,654 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+/ {
+	compatible = "xlnx,versal";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "Xilinx Versal";
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a72", "arm,armv8";
+			device_type = "cpu";
+			enable-method = "psci";
+			operating-points-v2 = <&cpu_opp_table>;
+			reg = <0>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a72", "arm,armv8";
+			device_type = "cpu";
+			enable-method = "psci";
+			operating-points-v2 = <&cpu_opp_table>;
+			reg = <1>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x40000000>;
+				local-timer-stop;
+				entry-latency-us = <300>;
+				exit-latency-us = <600>;
+				min-residency-us = <10000>;
+			};
+		};
+	};
+
+	cpu_opp_table: cpu_opp_table {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp00 {
+			opp-hz = /bits/ 64 <1199999988>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <500000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <599999994>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <500000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <399999996>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <500000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <299999997>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <500000>;
+		};
+	};
+
+	dcc: dcc {
+		compatible = "arm,dcc";
+		status = "disabled";
+		u-boot,dm-pre-reloc;
+	};
+
+	fpga: fpga {
+		compatible = "fpga-region";
+		fpga-mgr = <&versal_fpga>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+	};
+
+	psci: psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupt-parent = <&gic>;
+		interrupts = <1 7 0x304>;
+	};
+
+	timer: timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <1 13 4>,
+			     <1 14 4>,
+			     <1 11 4>,
+			     <1 10 4>;
+	};
+
+	versal_fpga: versal_fpga {
+		compatible = "xlnx,versal-fpga";
+	};
+
+	amba: axi {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		interrupt-parent = <&gic>;
+		u-boot,dm-pre-reloc;
+
+		gic: interrupt-controller@f9000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			reg = <0 0xf9000000 0 0x80000>, /* GICD */
+			      <0 0xf9080000 0 0x80000>; /* GICR */
+			interrupt-controller;
+			interrupts = <1 9 4>;
+
+			gic_its: gic-its@f9020000 {
+				compatible = "arm,gic-v3-its";
+				status = "disabled";
+				msi-controller;
+				msi-cells = <1>;
+				reg = <0 0xf9020000 0 0x20000>;
+			};
+		};
+
+		apm: performance-monitor@f0920000 {
+			compatible = "xlnx,flexnoc-pm-2.7";
+			status = "disabled";
+			reg-names = "funnel", "baselpd", "basefpd";
+			reg = <0x0 0xf0920000 0x0 0x1000>,
+			      <0x0 0xf0980000 0x0 0x9000>,
+			      <0x0 0xf0b80000 0x0 0x9000>;
+		};
+
+		can0: can@ff060000 {
+			compatible = "xlnx,canfd-2.0";
+			status = "disabled";
+			reg = <0 0xff060000 0 0x6000>;
+			interrupts = <0 20 4>;
+			clock-names = "can_clk", "s_axi_aclk";
+			rx-fifo-depth = <0x40>;
+			tx-mailbox-count = <0x20>;
+		};
+
+		can1: can@ff070000 {
+			compatible = "xlnx,canfd-2.0";
+			status = "disabled";
+			reg = <0 0xff070000 0 0x6000>;
+			interrupts = <0 21 4>;
+			clock-names = "can_clk", "s_axi_aclk";
+			rx-fifo-depth = <0x40>;
+			tx-mailbox-count = <0x20>;
+		};
+
+		cci: cci@fd000000 {
+			compatible = "arm,cci-500";
+			status = "disabled";
+			reg = <0 0xfd000000 0 0x10000>;
+			ranges = <0 0 0xfd000000 0xa0000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cci_pmu: pmu@10000 {
+				compatible = "arm,cci-500-pmu,r0";
+				reg = <0x10000 0x90000>;
+				interrupts = <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>,
+					     <0 106 4>;
+			};
+		};
+
+		lpd_dma_chan0: dma@ffa80000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffa80000 0 0x1000>;
+			interrupts = <0 60 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x210>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan1: dma@ffa90000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffa90000 0 0x1000>;
+			interrupts = <0 61 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x212>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan2: dma@ffaa0000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffaa0000 0 0x1000>;
+			interrupts = <0 62 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x214>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan3: dma@ffab0000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffab0000 0 0x1000>;
+			interrupts = <0 63 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x216>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan4: dma@ffac0000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffac0000 0 0x1000>;
+			interrupts = <0 64 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x218>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan5: dma@ffad0000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffad0000 0 0x1000>;
+			interrupts = <0 65 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x21a>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan6: dma@ffae0000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffae0000 0 0x1000>;
+			interrupts = <0 66 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x21c>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		lpd_dma_chan7: dma@ffaf0000 {
+			compatible = "xlnx,zynqmp-dma-1.0";
+			status = "disabled";
+			reg = <0 0xffaf0000 0 0x1000>;
+			interrupts = <0 67 4>;
+			clock-names = "clk_main", "clk_apb";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x21e>; */
+			xlnx,bus-width = <64>;
+			/* dma-coherent; */
+		};
+
+		gem0: ethernet@ff0c0000 {
+			compatible = "cdns,versal-gem", "cdns,gem";
+			status = "disabled";
+			reg = <0 0xff0c0000 0 0x1000>;
+			interrupts = <0 56 4>, <0 56 4>;
+			clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x234>; */
+			/* dma-coherent; */
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		gem1: ethernet@ff0d0000 {
+			compatible = "cdns,versal-gem", "cdns,gem";
+			status = "disabled";
+			reg = <0 0xff0d0000 0 0x1000>;
+			interrupts = <0 58 4>, <0 58 4>;
+			clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x235>; */
+			/* dma-coherent; */
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		gpio0: gpio@ff0b0000 {
+			compatible = "xlnx,versal-gpio-1.0";
+			status = "disabled";
+			reg = <0 0xff0b0000 0 0x1000>;
+			interrupts = <0 13 4>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		gpio1: gpio@f1020000 {
+			compatible = "xlnx,pmc-gpio-1.0";
+			status = "disabled";
+			reg = <0 0xf1020000 0 0x1000>;
+			interrupts = <0 122 4>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		i2c0: i2c@ff020000 {
+			compatible = "cdns,i2c-r1p14";
+			status = "disabled";
+			reg = <0 0xff020000 0 0x1000>;
+			interrupts = <0 14 4>;
+			clock-frequency = <400000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@ff030000 {
+			compatible = "cdns,i2c-r1p14";
+			status = "disabled";
+			reg = <0 0xff030000 0 0x1000>;
+			interrupts = <0 15 4>;
+			clock-frequency = <400000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@f1000000 {
+			compatible = "cdns,i2c-r1p14";
+			status = "disabled";
+			reg = <0 0xf1000000 0 0x1000>;
+			interrupts = <0 123 4>;
+			clock-frequency = <400000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mc0: memory-controller@f6150000	{
+			compatible = "xlnx,versal-ddrmc-edac";
+			status = "disabled";
+			reg = <0x0 0xf6150000 0x0 0x2000>, <0x0 0xf6070000 0x0 0x20000>;
+			reg-names = "ddrmc_base", "ddrmc_noc_base";
+			interrupts = <0 147 4>;
+			xlnx,mc-id = <0>;
+		};
+
+		mc1: memory-controller@f62c0000 {
+			compatible = "xlnx,versal-ddrmc-edac";
+			status = "disabled";
+			reg = <0x0 0xf62c0000 0x0 0x2000>, <0x0 0xf6210000 0x0 0x20000>;
+			reg-names = "ddrmc_base", "ddrmc_noc_base";
+			interrupts = <0 147 4>;
+			xlnx,mc-id = <1>;
+		};
+
+		mc2: memory-controller@f6430000 {
+			compatible = "xlnx,versal-ddrmc-edac";
+			status = "disabled";
+			reg = <0x0 0xf6430000 0x0 0x2000>, <0x0 0xf6380000 0x0 0x20000>;
+			reg-names = "ddrmc_base", "ddrmc_noc_base";
+			interrupts = <0 147 4>;
+			xlnx,mc-id = <2>;
+		};
+
+		mc3: memory-controller@f65a0000 {
+			compatible = "xlnx,versal-ddrmc-edac";
+			status = "disabled";
+			reg = <0x0 0xf65a0000 0x0 0x2000>, <0x0 0xf64f0000 0x0 0x20000>;
+			reg-names = "ddrmc_base", "ddrmc_noc_base";
+			interrupts = <0 147 4>;
+			xlnx,mc-id = <3>;
+		};
+
+		rtc: rtc@f12a0000 {
+			compatible = "xlnx,zynqmp-rtc";
+			status = "disabled";
+			reg = <0 0xf12a0000 0 0x100>;
+			interrupt-names = "alarm", "sec";
+			interrupts = <0 142 4>, <0 143 4>;
+			calibration = <0x7FFF>;
+		};
+
+		sdhci0: mmc@f1040000 {
+			compatible = "xlnx,versal-8.9a", "arasan,sdhci-8.9a";
+			status = "disabled";
+			reg = <0 0xf1040000 0 0x10000>;
+			interrupts = <0 126 4>;
+			clock-names = "clk_xin", "clk_ahb";
+			xlnx,device_id = <0>;
+			#stream-id-cells = <1>;
+			#clock-cells = <1>;
+			clock-output-names = "clk_out_sd0", "clk_in_sd0";
+			/* iommus = <&smmu 0x242>; */
+			/* dma-coherent; */
+		};
+
+		sdhci1: mmc@f1050000 {
+			compatible = "xlnx,versal-8.9a", "arasan,sdhci-8.9a";
+			status = "disabled";
+			reg = <0 0xf1050000 0 0x10000>;
+			interrupts = <0 128 4>;
+			clock-names = "clk_xin", "clk_ahb";
+			xlnx,device_id = <1>;
+			#stream-id-cells = <1>;
+			#clock-cells = <1>;
+			clock-output-names = "clk_out_sd1", "clk_in_sd1";
+			/* iommus = <&smmu 0x243>; */
+			/* dma-coherent; */
+		};
+
+		serial0: serial@ff000000 {
+			compatible = "arm,pl011", "arm,sbsa-uart";
+			status = "disabled";
+			reg = <0 0xff000000 0 0x1000>;
+			interrupts = <0 18 4>;
+			clock-names = "uart_clk", "apb_clk";
+			current-speed = <115200>;
+			u-boot,dm-pre-reloc;
+		};
+
+		serial1: serial@ff010000 {
+			compatible = "arm,pl011", "arm,sbsa-uart";
+			status = "disabled";
+			reg = <0 0xff010000 0 0x1000>;
+			interrupts = <0 19 4>;
+			clock-names = "uart_clk", "apb_clk";
+			current-speed = <115200>;
+			u-boot,dm-pre-reloc;
+		};
+
+		smmu: smmu@fd800000 {
+			compatible = "arm,mmu-500";
+			status = "disabled";
+			reg = <0 0xfd800000 0 0x40000>;
+			stream-match-mask = <0x7c00>;
+			#iommu-cells = <1>;
+			#global-interrupts = <1>;
+			interrupts = <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>,
+				     <0 107 4>, <0 107 4>, <0 107 4>, <0 107 4>;
+		};
+
+		ospi: spi@f1010000 {
+			compatible = "xlnx,versal-ospi-1.0", "cadence,qspi", "cdns,qspi-nor";
+			status = "disabled";
+			reg = <0 0xf1010000 0 0x10000 0 0xc0000000 0 0x20000000>;
+			interrupts = <0 124 4>, <0 124 4>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,is-dma = <1>;
+			cdns,is-stig-pgm = <1>;
+			cdns,trigger-address = <0xC0000000>;
+			#stream-id-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		qspi: spi@f1030000 {
+			compatible = "xlnx,versal-qspi-1.0";
+			status = "disabled";
+			reg = <0 0xf1030000 0 0x1000>;
+			interrupts = <0 125 4>, <0 125 4>;
+			clock-names = "ref_clk", "pclk";
+			#stream-id-cells = <1>;
+			/* iommus = <&smmu 0x244>; */
+			/* dma-coherent; */
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@ff040000 {
+			compatible = "cdns,spi-r1p6";
+			status = "disabled";
+			reg = <0 0xff040000 0 0x1000>;
+			interrupts = <0 16 4>;
+			clock-names = "ref_clk", "pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@ff050000 {
+			compatible = "cdns,spi-r1p6";
+			status = "disabled";
+			reg = <0 0xff050000 0 0x1000>;
+			interrupts = <0 17 4>;
+			clock-names = "ref_clk", "pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		sysmon0: sysmon@f1270000 {
+			compatible = "xlnx,versal-sysmon";
+			reg = <0x0 0xf1270000 0x0 0x4000>;
+			interrupts = <0 144 4>;
+			xlnx,numchannels = /bits/8 <0>;
+		};
+		sysmon1: sysmon@109270000 {
+			compatible = "xlnx,versal-sysmon";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			status = "disabled";
+			reg = <0x1 0x09270000 0x0 0x4000>;
+			xlnx,numchannels = /bits/8 <0>;
+		};
+
+		sysmon2: sysmon@111270000 {
+			compatible = "xlnx,versal-sysmon";
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x1 0x11270000 0x0 0x4000>;
+			xlnx,numchannels = /bits/8 <0>;
+		};
+		sysmon3: sysmon@119270000 {
+			compatible = "xlnx,versal-sysmon";
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x1 0x19270000 0x0 0x4000>;
+			xlnx,numchannels = /bits/8 <0>;
+		};
+
+		ttc0: timer@ff0e0000 {
+			compatible = "cdns,ttc";
+			status = "disabled";
+			interrupts = <0 37 4>, <0 38 4>, <0 39 4>;
+			reg = <0x0 0xff0e0000 0x0 0x1000>;
+			timer-width = <32>;
+		};
+
+		ttc1: timer@ff0f0000 {
+			compatible = "cdns,ttc";
+			status = "disabled";
+			interrupts = <0 40 4>, <0 41 4>, <0 42 4>;
+			reg = <0x0 0xff0f0000 0x0 0x1000>;
+			timer-width = <32>;
+		};
+
+		ttc2: timer@ff100000 {
+			compatible = "cdns,ttc";
+			status = "disabled";
+			interrupts = <0 43 4>, <0 44 4>, <0 45 4>;
+			reg = <0x0 0xff100000 0x0 0x1000>;
+			timer-width = <32>;
+		};
+
+		ttc3: timer@ff110000 {
+			compatible = "cdns,ttc";
+			status = "disabled";
+			interrupts = <0 46 4>, <0 47 4>, <0 48 4>;
+			reg = <0x0 0xff110000 0x0 0x1000>;
+			timer-width = <32>;
+		};
+
+		usb0: usb@ff9d0000 {
+			compatible = "xlnx,versal-dwc3";
+			status = "disabled";
+			reg = <0 0xff9d0000 0 0x100>;
+			clock-names = "bus_clk", "ref_clk";
+			ranges;
+			#address-cells = <2>;
+			#size-cells = <2>;
+
+			dwc3_0: usb@fe200000 {
+				compatible = "snps,dwc3";
+				status = "disabled";
+				reg = <0 0xfe200000 0 0x10000>;
+				interrupt-names = "dwc_usb3", "otg", "usb-wakeup";
+				interrupts = <0 0x16 4>, <0 0x1A 4>, <0x0 0x4a 0x4>;
+				#stream-id-cells = <1>;
+				/* iommus = <&smmu 0x230>; */
+				snps,dis_u2_susphy_quirk;
+				snps,dis_u3_susphy_quirk;
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,refclk_fladj;
+				snps,mask_phy_reset;
+				/* dma-coherent; */
+			};
+		};
+
+		cpm_pciea: pci@fca10000 {
+			#address-cells = <3>;
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			compatible = "xlnx,versal-cpm-host-1.00";
+			status = "disabled";
+			interrupt-map = <0 0 0 1 &pcie_intc_0 0>,
+					<0 0 0 2 &pcie_intc_0 1>,
+					<0 0 0 3 &pcie_intc_0 2>,
+					<0 0 0 4 &pcie_intc_0 3>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-names = "misc";
+			interrupts = <0 72 4>;
+			ranges = <0x02000000 0x00000000 0xe0000000 0x0 0xe0000000 0x00000000 0x10000000>,
+				 <0x43000000 0x00000080 0x00000000 0x00000080 0x00000000 0x00000000 0x80000000>;
+			msi-map = <0x0 &gic_its 0x0 0x10000>;
+			reg = <0x0 0xfca10000 0x0 0x1000>,
+			      <0x6 0x00000000 0x0 0x1000000>;
+			reg-names = "cpm_slcr", "cfg";
+			pcie_intc_0: pci-interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller ;
+			};
+		};
+
+		watchdog: watchdog@fd4d0000 {
+			compatible = "xlnx,versal-wwdt-1.0";
+			status = "disabled";
+			reg = <0 0xfd4d0000 0 0x10000>;
+			interrupt-names = "wdt", "wwdt_reset_pending";
+			interrupts = <0 0x64 1>, <0 0x6D 1>;
+			timeout-sec = <30>;
+			pretimeout-sec = <25>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-a2197-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-a2197-revA.dts
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Versal System Controller on a2197 board RevA";
+	compatible = "xlnx,zynqmp-a2197-revA", "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		i2c0 = &i2c0;
+		nvmem0 = &eeprom1;
+		nvmem1 = &eeprom0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	u-boot,dm-pre-reloc;
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* this cover MGT board */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		u-boot,dm-pre-reloc;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom0: eeprom@50 { /* u96 - 24LC32A - 256B */
+				compatible = "atmel,24c32";
+				u-boot,dm-pre-reloc;
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	u-boot,dm-pre-reloc;
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* This cover processor board */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		u-boot,dm-pre-reloc;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom1: eeprom@50 { /* u96 - 24LC32A - 256B */
+				compatible = "atmel,24c32";
+				u-boot,dm-pre-reloc;
+				reg = <0x50>;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
@@ -2,44 +2,85 @@
 /*
  * Clock specification for Xilinx ZynqMP
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
 
 #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
 / {
+	fclk0: fclk0 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&zynqmp_clk PL0_REF>;
+	};
+
+	fclk1: fclk1 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&zynqmp_clk PL1_REF>;
+	};
+
+	fclk2: fclk2 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&zynqmp_clk PL2_REF>;
+	};
+
+	fclk3: fclk3 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&zynqmp_clk PL3_REF>;
+	};
+
 	pss_ref_clk: pss_ref_clk {
+		u-boot,dm-pre-reloc;
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <33333333>;
 	};
 
 	video_clk: video_clk {
+		u-boot,dm-pre-reloc;
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <27000000>;
 	};
 
 	pss_alt_ref_clk: pss_alt_ref_clk {
+		u-boot,dm-pre-reloc;
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <0>;
 	};
 
 	gt_crx_ref_clk: gt_crx_ref_clk {
+		u-boot,dm-pre-reloc;
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <108000000>;
 	};
 
 	aux_ref_clk: aux_ref_clk {
+		u-boot,dm-pre-reloc;
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <27000000>;
 	};
 };
 
+&zynqmp_firmware {
+	zynqmp_clk: clock-controller {
+		u-boot,dm-pre-reloc;
+		#clock-cells = <1>;
+		compatible = "xlnx,zynqmp-clk";
+		clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>,
+			 <&aux_ref_clk>, <&gt_crx_ref_clk>;
+		clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk",
+			      "aux_ref_clk", "gt_crx_ref_clk";
+	};
+};
+
 &can0 {
 	clocks = <&zynqmp_clk CAN0_REF>, <&zynqmp_clk LPD_LSBUS>;
 };
@@ -84,6 +125,10 @@
 	clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
 };
 
+&gpu {
+	clocks = <&zynqmp_clk GPU_REF>, <&zynqmp_clk GPU_PP0_REF>, <&zynqmp_clk GPU_PP1_REF>;
+};
+
 &lpd_dma_chan1 {
 	clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
 };
@@ -124,28 +169,28 @@
 	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>,
 		 <&zynqmp_clk GEM0_TX>, <&zynqmp_clk GEM0_RX>,
 		 <&zynqmp_clk GEM_TSU>;
-	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+	assigned-clocks = <&zynqmp_clk GEM_TSU>;
 };
 
 &gem1 {
 	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>,
 		 <&zynqmp_clk GEM1_TX>, <&zynqmp_clk GEM1_RX>,
 		 <&zynqmp_clk GEM_TSU>;
-	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+	assigned-clocks = <&zynqmp_clk GEM_TSU>;
 };
 
 &gem2 {
 	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM2_REF>,
 		 <&zynqmp_clk GEM2_TX>, <&zynqmp_clk GEM2_RX>,
 		 <&zynqmp_clk GEM_TSU>;
-	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+	assigned-clocks = <&zynqmp_clk GEM_TSU>;
 };
 
 &gem3 {
 	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM3_REF>,
 		 <&zynqmp_clk GEM3_TX>, <&zynqmp_clk GEM3_RX>,
 		 <&zynqmp_clk GEM_TSU>;
-	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+	assigned-clocks = <&zynqmp_clk GEM_TSU>;
 };
 
 &gpio {
@@ -160,6 +205,22 @@
 	clocks = <&zynqmp_clk I2C1_REF>;
 };
 
+&perf_monitor_ocm {
+	clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&perf_monitor_ddr {
+	clocks = <&zynqmp_clk TOPSW_LSBUS>;
+};
+
+&perf_monitor_cci {
+	clocks = <&zynqmp_clk TOPSW_LSBUS>;
+};
+
+&perf_monitor_lpd {
+	clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
 &pcie {
 	clocks = <&zynqmp_clk PCIE_REF>;
 };
@@ -174,10 +235,12 @@
 
 &sdhci0 {
 	clocks = <&zynqmp_clk SDIO0_REF>, <&zynqmp_clk LPD_LSBUS>;
+	assigned-clocks = <&zynqmp_clk SDIO0_REF>;
 };
 
 &sdhci1 {
 	clocks = <&zynqmp_clk SDIO1_REF>, <&zynqmp_clk LPD_LSBUS>;
+	assigned-clocks = <&zynqmp_clk SDIO1_REF>;
 };
 
 &spi0 {
@@ -214,10 +277,20 @@
 
 &usb0 {
 	clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+	assigned-clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+};
+
+&dwc3_0 {
+	clocks = <&zynqmp_clk USB3_DUAL_REF>;
 };
 
 &usb1 {
 	clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+	assigned-clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+};
+
+&dwc3_1 {
+	clocks = <&zynqmp_clk USB3_DUAL_REF>;
 };
 
 &watchdog0 {
@@ -228,12 +301,24 @@
 	clocks = <&zynqmp_clk LPD_WDT>;
 };
 
+&xilinx_ams {
+	clocks = <&zynqmp_clk AMS_REF>;
+};
+
 &zynqmp_dpdma {
 	clocks = <&zynqmp_clk DPDMA_REF>;
+	assigned-clocks = <&zynqmp_clk DPDMA_REF>; /* apll */
 };
 
 &zynqmp_dpsub {
 	clocks = <&zynqmp_clk TOPSW_LSBUS>,
-		 <&zynqmp_clk DP_AUDIO_REF>,
-		 <&zynqmp_clk DP_VIDEO_REF>;
+		<&zynqmp_clk DP_AUDIO_REF>,
+		<&zynqmp_clk DP_VIDEO_REF>;
+	assigned-clocks = <&zynqmp_clk DP_STC_REF>,
+			  <&zynqmp_clk DP_AUDIO_REF>,
+			  <&zynqmp_clk DP_VIDEO_REF>;  /* rpll, rpll, vpll */
+};
+
+&zynqmp_dp_snd_codec0 {
+	clocks = <&zynqmp_clk DP_AUDIO_REF>;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Clock specification for Xilinx ZynqMP
+ *
+ * (C) Copyright 2015 - 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/ {
+	clk100: clk100 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		u-boot,dm-pre-reloc;
+	};
+
+	clk125: clk125 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	clk200: clk200 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <200000000>;
+		u-boot,dm-pre-reloc;
+	};
+
+	clk250: clk250 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <250000000>;
+	};
+
+	clk300: clk300 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <300000000>;
+		u-boot,dm-pre-reloc;
+	};
+
+	clk600: clk600 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <600000000>;
+	};
+
+	dp_aclk: clock0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-accuracy = <100>;
+	};
+
+	dp_aud_clk: clock1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+		clock-accuracy = <100>;
+	};
+
+	dpdma_clk: dpdma-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0x0>;
+		clock-frequency = <533000000>;
+	};
+
+	drm_clock: drm-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0x0>;
+		clock-frequency = <262750000>;
+		clock-accuracy = <0x64>;
+	};
+};
+
+&can0 {
+	clocks = <&clk100 &clk100>;
+};
+
+&can1 {
+	clocks = <&clk100 &clk100>;
+};
+
+&fpd_dma_chan1 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan2 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan3 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan4 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan5 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan6 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan7 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan8 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan1 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan2 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan3 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan4 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan5 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan6 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan7 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan8 {
+	clocks = <&clk600>, <&clk100>;
+};
+
+&nand0 {
+	clocks = <&clk100 &clk100>;
+};
+
+&gem0 {
+	clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem1 {
+	clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem2 {
+	clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem3 {
+	clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gpio {
+	clocks = <&clk100>;
+};
+
+&i2c0 {
+	clocks = <&clk100>;
+};
+
+&i2c1 {
+	clocks = <&clk100>;
+};
+
+&perf_monitor_ocm {
+	clocks = <&clk100>;
+};
+
+&perf_monitor_ddr {
+	clocks = <&clk100>;
+};
+
+&perf_monitor_cci {
+	clocks = <&clk100>;
+};
+
+&perf_monitor_lpd {
+	clocks = <&clk100>;
+};
+
+&qspi {
+	clocks = <&clk300 &clk300>;
+};
+
+&sata {
+	clocks = <&clk250>;
+};
+
+&sdhci0 {
+	clocks = <&clk200 &clk200>;
+};
+
+&sdhci1 {
+	clocks = <&clk200 &clk200>;
+};
+
+&spi0 {
+	clocks = <&clk200 &clk200>;
+};
+
+&spi1 {
+	clocks = <&clk200 &clk200>;
+};
+
+&uart0 {
+	clocks = <&clk100 &clk100>;
+};
+
+&uart1 {
+	clocks = <&clk100 &clk100>;
+};
+
+&usb0 {
+	clocks = <&clk250>, <&clk250>;
+};
+
+&usb1 {
+	clocks = <&clk250>, <&clk250>;
+};
+
+&watchdog0 {
+	clocks = <&clk100>;
+};
+
+&lpd_watchdog {
+	clocks = <&clk250>;
+};
+
+&zynqmp_dpsub {
+	clocks = <&dp_aclk>, <&dp_aud_clk>, <&drm_clock>;
+};
+
+&zynqmp_dpdma {
+	clocks = <&dpdma_clk>;
+};
+
+&zynqmp_dp_snd_codec0 {
+	clocks = <&dp_aud_clk>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-dlc21-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-dlc21-revA.dts
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP DLC21 revA
+ *
+ * (C) Copyright 2019 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "Smartlynq+ DLC21 RevA";
+	compatible = "xlnx,zynqmp-dlc21-revA", "xlnx,zynqmp-dlc21",
+		     "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		gpio0 = &gpio;
+		i2c0 = &i2c0;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial2 = &dcc;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		spi0 = &spi0;
+		nvmem0 = &eeprom;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0 0x3 0x80000000>;
+	};
+
+	si5332_1: si5332_1 { /* clk0_sgmii - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	si5332_2: si5332_2 { /* clk1_usb - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings  16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio_bank = <0>;
+};
+
+&sdhci1 { /* sd1 MIO45-51 cd in place */
+	status = "okay";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio_bank = <1>;
+};
+
+&psgtr {
+	status = "okay";
+	/* sgmii, usb3 */
+	clocks = <&si5332_1>, <&si5332_2>;
+	clock-names = "ref0", "ref1";
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+	u-boot,dm-pre-reloc;
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii"; /* DTG generates this properly  1512 */
+	is-internal-pcspma;
+	/* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "", "", "", "", "", /* 0 - 4 */
+		  "", "", "", "", "", /* 5 - 9 */
+		  "", "", "", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "DISP_SCL", "DISP_DC_B", "DISP_RES_B", "DISP_CS_B", /* 25 - 29 */
+		  "", "DISP_SDI", "SYSTEM_RST_R_B", "", "I2C0_SCL", /* 30 - 34 */
+		  "I2C0_SDA", "", "", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "", "", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */
+		  "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */
+		  "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */
+		  "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "VCCO_500_RBIAS", "VCCO_501_RBIAS", "VCCO_502_RBIAS", "VCCO_500_RBIAS_LED", /* 95 - 99 */
+		  "VCCO_501_RBIAS_LED", "VCCO_502_RBIAS_LED", "SYSCTLR_VCCINT_EN", "SYSCTLR_VCC_IO_SOC_EN", "SYSCTLR_VCC_PMC_EN", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "SYSCTLR_VCCO_500_EN", "SYSCTLR_VCCO_501_EN", "SYSCTLR_VCCO_502_EN", "SYSCTLR_VCCO_503_EN", "SYSCTLR_VCC1V8_EN", /* 110 - 114 */
+		  "SYSCTLR_VCC3V3_EN", "SYSCTLR_VCC1V2_DDR4_EN", "SYSCTLR_VCC1V1_LP4_EN", "SYSCTLR_VDD1_1V8_LP4_EN", "SYSCTLR_VADJ_FMC_EN", /* 115 - 119 */
+		  "", "", "", "SYSCTLR_UTIL_1V13_EN", "SYSCTLR_UTIL_1V8_EN", /* 120 - 124 */
+		  "SYSCTLR_UTIL_2V5_EN", "", "", "", "", /* 125 - 129 */
+		  "", "", "SYSCTLR_USBC_SBU1", "SYSCTLR_USBC_SBU2", "", /* 130 - 134 */
+		  "", "SYSCTLR_MIC2005_EN_B", "SYSCTLR_MIC2005_FAULT_B", "SYSCTLR_TUSB320_INT_B", "SYSCTLR_TUSB320_ID", /* 135 - 139 */
+		  "", "", "SYSCTLR_ETH_RESET_B", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO34/35 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	jtag_vref: mcp4725@62 {
+		compatible = "microchip,mcp4725";
+		reg = <0x62>;
+		vref-millivolt = <3300>;
+	};
+
+	eeprom: eeprom@50 { /* u46 */
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+	};
+	/* u138 - TUSB320IRWBR - for USB-C */
+};
+
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	maximum-speed = "super-speed";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
+};
+
+&usb1 {
+	status = "disabled"; /* Any unknown issue with USB-C */
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_1 {
+	/delete-property/ phy-names ;
+	/delete-property/ phys ;
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk ;
+	snps,dis_u3_susphy_quirk ;
+	status = "okay";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	is-decoded-cs = <0>;
+	num-cs = <1>;
+	u-boot,dm-pre-reloc;
+	displayspi@0 {
+		compatible = "syncoam,seps525";
+		u-boot,dm-pre-reloc;
+		reg = <0>;
+		status = "okay";
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+		rotate = <0>;
+		fps = <50>;
+		buswidth = <8>;
+		txbuflen = <64000>;
+		reset-gpios = <&gpio 0x1c GPIO_ACTIVE_LOW>;
+		dc-gpios = <&gpio 0x1b GPIO_ACTIVE_HIGH>;
+		debug = <0>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-e-a2197-00-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-e-a2197-00-revA.dts
@@ -0,0 +1,668 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller
+ *
+ * (C) Copyright 2019 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "Versal System Controller on a2197 Eval board RevA"; /* VCK190/VMK180 */
+	compatible = "xlnx,zynqmp-e-a2197-00-revA", "xlnx,zynqmp-a2197-revA",
+		     "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
+		nvmem1 = &eeprom_ebm;
+		nvmem2 = &eeprom_fmc1;
+		nvmem3 = &eeprom_fmc2;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ref_clk: ref_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_ref_clk>;
+	};
+
+	si570_ddrdimm1_clk: si570_ddrdimm1_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_ddr_dimm1>;
+	};
+
+	si570_lpddr4_clk2: si570_lpddr4_clk2 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_lpddr4clk2>;
+	};
+
+	si570_lpddr4_clk1: si570_lpddr4_clk1 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_lpddr4clk1>;
+	};
+
+	si570_hsdp_clk: si570_hsdp_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_hsdp>;
+	};
+
+	si570_zsfp_clk: si570_zsfp_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_zsfp>;
+	};
+
+	si570_user1_clk: si570_user1_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_user1>;
+	};
+
+	si5332_1: si5332_1 { /* u142 - GEM0 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	ina226-vccint {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint 0>, <&vccint 1>, <&vccint 2>, <&vccint 3>;
+	};
+	ina226-vcc-soc {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_soc 0>, <&vcc_soc 1>, <&vcc_soc 2>, <&vcc_soc 3>;
+	};
+	ina226-vcc-pmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_pmc 0>, <&vcc_pmc 1>, <&vcc_pmc 2>, <&vcc_pmc 3>;
+	};
+	ina226-vcc-ram {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_ram 0>, <&vcc_ram 1>, <&vcc_ram 2>, <&vcc_ram 3>;
+	};
+	ina226-vcc-pslp {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_pslp 0>, <&vcc_pslp 1>, <&vcc_pslp 2>, <&vcc_pslp 3>;
+	};
+	ina226-vcc-psfp {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_psfp 0>, <&vcc_psfp 1>, <&vcc_psfp 2>, <&vcc_psfp 3>;
+	};
+	ina226-vccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&vccaux 0>, <&vccaux 1>, <&vccaux 2>, <&vccaux 3>;
+	};
+	ina226-vccaux-pmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vccaux_pmc 0>, <&vccaux_pmc 1>, <&vccaux_pmc 2>, <&vccaux_pmc 3>;
+	};
+	ina226-vcco-500 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcco_500 0>, <&vcco_500 1>, <&vcco_500 2>, <&vcco_500 3>;
+	};
+	ina226-vcco-501 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcco_501 0>, <&vcco_501 1>, <&vcco_501 2>, <&vcco_501 3>;
+	};
+	ina226-vcco-502 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcco_502 0>, <&vcco_502 1>, <&vcco_502 2>, <&vcco_502 3>;
+	};
+	ina226-vcco-503 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcco_503 0>, <&vcco_503 1>, <&vcco_503 2>, <&vcco_503 3>;
+	};
+	ina226-vcc-1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_1v8 0>, <&vcc_1v8 1>, <&vcc_1v8 2>, <&vcc_1v8 3>;
+	};
+	ina226-vcc-3v3 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_3v3 0>, <&vcc_3v3 1>, <&vcc_3v3 2>, <&vcc_3v3 3>;
+	};
+	ina226-vcc-1v2-ddr4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_1v2_ddr4 0>, <&vcc_1v2_ddr4 1>, <&vcc_1v2_ddr4 2>, <&vcc_1v2_ddr4 3>;
+	};
+	ina226-vcc-1v1-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v1_lp4 0>, <&vcc1v1_lp4 1>, <&vcc1v1_lp4 2>, <&vcc1v1_lp4 3>;
+	};
+	ina226-vadj-fmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vadj_fmc 0>, <&vadj_fmc 1>, <&vadj_fmc 2>, <&vadj_fmc 3>;
+	};
+	ina226-mgtyavcc {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtyavcc 0>, <&mgtyavcc 1>, <&mgtyavcc 2>, <&mgtyavcc 3>;
+	};
+	ina226-mgtyavtt {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtyavtt 0>, <&mgtyavtt 1>, <&mgtyavtt 2>, <&mgtyavtt 3>;
+	};
+	ina226-mgtyvccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtyvccaux 0>, <&mgtyvccaux 1>, <&mgtyvccaux 2>, <&mgtyvccaux 3>;
+	};
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&sdhci1 { /* sd1 MIO45-51 cd in place */
+	status = "okay";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+/* GEM SGMII */
+&psgtr {
+	status = "okay";
+	/* gem0 */
+	clocks = <&si5332_1>;
+	clock-names = "ref0";
+};
+
+&gem0 {
+	status = "okay";
+	phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>;
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	is-internal-pcspma;
+	phy0: ethernet-phy@0 { /* u131 M88E1512 */
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "", "", "", "", "", /* 0 - 4 */
+		  "", "", "DC_SYS_CTRL0", "DC_SYS_CTRL1", "DC_SYS_CTRL2", /* 5 - 9 */
+		  "DC_SYS_CTRL3", "ZU4_TRIGGER", "SYSCTLR_PB", "", "", /* 10 - 14 */
+		  "", "", "", "", "", /* 15 - 19 */
+		  "", "", "", "", "", /* 20 - 24 */
+		  "", "", "", "", "", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "", "", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "", "", "", /* 50 - 54 */
+		  "", "", "", "", "", /* 55 - 59 */
+		  "", "", "", "", "", /* 60 - 64 */
+		  "", "", "", "", "", /* 65 - 69 */
+		  "", "", "", "", "", /* 70 - 74 */
+		  "", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "SYSCTLR_VERSAL_MODE0", "SYSCTLR_VERSAL_MODE1", /* 78 - 79 */
+		  "SYSCTLR_VERSAL_MODE2", "SYSCTLR_VERSAL_MODE3", "SYSCTLR_POR_B_LS", "DC_PRSNT", "", /* 80 - 84 */
+		  "SYSCTLR_JTAG_S0", "SYSCTLR_JTAG_S1", "SYSCTLR_IIC_MUX0_RESET_B", "SYSCTLR_IIC_MUX1_RESET_B", "", /* 85 - 89 */
+		  "SYSCTLR_GPIO0", "SYSCTLR_GPIO1", "SYSCTLR_GPIO2", "SYSCTLR_GPIO3", "SYSCTLR_GPIO4", /* 90 - 94 */
+		  "SYSCTLR_GPIO5", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "PMBUS1_INA226_ALERT", "PMBUS2_INA226_ALERT", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "PMBUS_ALERT", "", "SYSCTLR_ETH_RESET_B", "SYSCTLR_VCC0V85_TG", "MAX6643_OT_B", /* 140 - 144 */
+		  "MAX6643_FANFINAL_B", "MAX6643_FULLSPD", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* u33 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 { /* PMBUS */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* u152 IR35215 0x16/0x46 vcc_soc */
+			/* u179 ir38164 0x19/0x49 vcco_500 */
+			/* u181 ir38164 0x1a/0x4a vcco_501 */
+			/* u183 ir38164 0x1b/0x4b vcco_502 */
+			/* u185 ir38164 0x1e/0x4e vadj_fmc */
+			/* u187 ir38164 0x1F/0x4f mgtyavcc */
+			/* u189 ir38164 0x20/0x50 mgtyavtt */
+			/* u194 ir38164 0x13/0x43 vdd1_1v8_lp4 */
+			/* u195 ir38164 0x14/0x44 vdd2_1v8_lp4 */
+
+			irps5401_47: irps5401@47 { /* IRPS5401 - u160 */
+				compatible = "infineon,irps5401";
+				reg = <0x47>; /* pmbus / i2c 0x17 */
+			};
+			irps5401_4c: irps5401@4c { /* IRPS5401 - u167 */
+				compatible = "infineon,irps5401";
+				reg = <0x4c>; /* pmbus / i2c 0x1c */
+			};
+			irps5401_4d: irps5401@4d { /* IRPS5401 - u175 */
+				compatible = "infineon,irps5401";
+				reg = <0x4d>; /* pmbus / i2c 0x1d */
+			};
+		};
+		i2c@1 { /* PMBUS1_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME check alerts coming to SC */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint";
+				reg = <0x40>;
+				shunt-resistor = <500>; /* R440 */
+				/* 0.80V @ 32A 1 of 6 Phases*/
+			};
+			vcc_soc: ina226@41 { /* u161 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-soc";
+				reg = <0x41>;
+				shunt-resistor = <500>; /* R1702 */
+				/* 0.80V @ 18A */
+			};
+			vcc_pmc: ina226@42 { /* u163 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-pmc";
+				reg = <0x42>;
+				shunt-resistor = <5000>; /* R1214 */
+				/* 0.78V @ 500mA */
+			};
+			vcc_ram: ina226@43 { /* u162 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-ram";
+				reg = <0x43>;
+				shunt-resistor = <5000>; /* r1221 */
+				/* 0.78V @ 4A */
+			};
+			vcc_pslp: ina226@44 { /* u165 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-pslp";
+				reg = <0x44>;
+				shunt-resistor = <5000>; /* R1216 */
+				/* 0.78V @ 1A */
+			};
+			vcc_psfp: ina226@45 { /* u164 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-psfp";
+				reg = <0x45>;
+				shunt-resistor = <5000>; /* R1219 */
+				/* 0.78V @ 2A */
+			};
+		};
+		i2c@2 { /* PCIE_CLK */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			clock_8t49n287: clock-generator@d8 { /* u39 8T49N240 */
+				#clock-cells = <1>; /* author David Cater <david.cater@idt.com>*/
+				compatible = "idt,8t49n240", "idt,8t49n241"; /* FIXME no driver for 240 */
+				reg = <0xd8>;
+				/* Documentation/devicetree/bindings/clock/idt,idt8t49n24x.txt */
+				/* FIXME there input via J241 Samtec CLK1 and CLK0 from U38 - selection PIN */
+			};
+		};
+		i2c@3 { /* PMBUS2_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FIXME check alerts coming to SC */
+			vccaux: ina226@40 { /* u166 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccaux";
+				reg = <0x40>;
+				shunt-resistor = <5000>; /* R382 */
+				/* 1.5V @ 3A */
+			};
+			vccaux_pmc: ina226@41 { /* u168 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccaux-pmc";
+				reg = <0x41>;
+				shunt-resistor = <5000>; /* R1246 */
+				/* 1.5V @ 500mA */
+			};
+			vcco_500: ina226@42 { /* u178 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcco-500";
+				reg = <0x42>;
+				shunt-resistor = <2000>; /* R1300 */
+				/* 3.3V @ 5A */
+			};
+			vcco_501: ina226@43 { /* u180 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcco-501";
+				reg = <0x43>;
+				shunt-resistor = <2000>; /* R1313 */
+				/* 3.3V @ 5A */
+			};
+			vcco_502: ina226@44 { /* u182 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcco-502";
+				reg = <0x44>;
+				shunt-resistor = <2000>; /* R1330 */
+				/* 3.3V @ 5A */
+			};
+			vcco_503: ina226@45 { /* u172 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcco-503";
+				reg = <0x45>;
+				shunt-resistor = <5000>; /* R1229 */
+				/* 1.8V @ 2A */
+			};
+			vcc_1v8: ina226@46 { /* u173 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-1v8";
+				reg = <0x46>;
+				shunt-resistor = <5000>; /* R400 */
+				/* 1.8V @ 6A */
+			};
+			vcc_3v3: ina226@47 { /* u174 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-3v3";
+				reg = <0x47>;
+				shunt-resistor = <5000>; /* R1232 */
+				/* 3.3V @ 500mA */
+			};
+			vcc_1v2_ddr4: ina226@48 { /* u176 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-1v2-ddr4";
+				reg = <0x48>;
+				shunt-resistor = <5000>; /* R1275 */
+				/* 1.2V @ 4A */
+			};
+			vcc1v1_lp4: ina226@49 { /* u177 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v1-lp4";
+				reg = <0x49>;
+				shunt-resistor = <5000>; /* R1286 */
+				/* 1.1V @ 4A */
+			};
+			vadj_fmc: ina226@4a { /* u184 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vadj-fmc";
+				reg = <0x4a>;
+				shunt-resistor = <2000>; /* R1350 */
+				/* 1.5V @ 10A */
+			};
+			mgtyavcc: ina226@4b { /* u186 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtyavcc";
+				reg = <0x4b>;
+				shunt-resistor = <2000>; /* R1367 */
+				/* 0.88V @ 6A */
+			};
+			mgtyavtt: ina226@4c { /* u188 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtyavtt";
+				reg = <0x4c>;
+				shunt-resistor = <2000>; /* R1384 */
+				/* 1.2V @ 10A */
+			};
+			mgtyvccaux: ina226@4d { /* u234 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtyvccaux";
+				reg = <0x4d>;
+				shunt-resistor = <5000>; /* r1679 */
+				/* 1.5V @ 500mA */
+			};
+		};
+		i2c@4 { /* LP_I2C_SM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* FIXME wires ready but chip is missing */
+		};
+		i2c@5 { /* zSFP_SI570 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			si570_zsfp: clock-generator@5d { /* u192 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "si570_zsfp_clk";
+			};
+		};
+		i2c@6 { /* USER_SI570_1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			si570_user1: clock-generator@5d { /* u205 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5f>;
+				temperature-stability = <50>;
+				factory-fout = <100000000>;
+				clock-frequency = <100000000>;
+				clock-output-names = "si570_user1";
+			};
+
+		};
+		i2c@7 { /* USER_SI570_2 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* FIXME wires ready but chip is missing */
+		};
+	};
+};
+
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	i2c-mux@74 { /* u35 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c-mux-idle-disconnect;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		dc_i2c: i2c@0 { /* DC_I2C */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u34 - m24128 16kB */
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x54>; /* 0x5c too */
+			};
+			si570_ref_clk: clock-generator@5d { /* u32 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "ref_clk";
+				silabs,skip-recall;
+			};
+			/* and connector J212D */
+			eeprom_ebm: eeprom@52 { /* x-ebm module */
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x52>;
+			};
+		};
+		fmc1: i2c@1 { /* FMCP1_IIC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME connection to Samtec J51C */
+			/* expected eeprom 0x50 FMC cards */
+			eeprom_fmc1: eeprom@50 {
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+		fmc2: i2c@2 { /* FMCP2_IIC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* FIXME connection to Samtec J53C */
+			/* expected eeprom 0x50 FMC cards */
+			eeprom_fmc2: eeprom@50 {
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+		i2c@3 { /* DDR4_DIMM1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_ddr_dimm1: clock-generator@60 { /* u2 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "si570_ddrdimm1_clk";
+				silabs,skip-recall;
+			};
+		};
+		i2c@4 { /* LPDDR4_SI570_CLK2 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			si570_lpddr4clk2: clock-generator@60 { /* u3 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "si570_lpddr4_clk2";
+			};
+		};
+		i2c@5 { /* LPDDR4_SI570_CLK1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			si570_lpddr4clk1: clock-generator@60 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "si570_lpddr4_clk1";
+			};
+		};
+		i2c@6 { /* HSDP_SI570 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			si570_hsdp: clock-generator@5d { /* u5 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "si570_hsdp_clk";
+			};
+		};
+		i2c@7 { /* 8A34001 - U219B and J310 connector */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+	i2c-mux@75 { /* u214 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+		i2c@0 { /* SFP0_IIC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* SFP0 */
+		};
+		i2c@1 { /* SFP1_IIC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* SFP1 */
+		};
+		i2c@2 { /* QSFP1_I2C */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* QSFP1 */
+		};
+		/* 3 - 7 unused */
+	};
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-g-a2197-00-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-g-a2197-00-revA.dts
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller on MGT
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Versal System Controller on a2197 MGT Char board RevA";
+	compatible = "xlnx,zynqmp-g-a2197-00-revA", "xlnx,zynqmp-a2197-revA",
+		     "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		mmc0 = &sdhci0;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ina226-u74 {
+		compatible = "iio-hwmon";
+		io-channels = <&u74 0>, <&u74 1>, <&u74 2>, <&u74 3>;
+	};
+	ina226-u75 {
+		compatible = "iio-hwmon";
+		io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>;
+	};
+	ina226-u78 {
+		compatible = "iio-hwmon";
+		io-channels = <&u78 0>, <&u78 1>, <&u78 2>, <&u78 3>;
+	};
+	ina226-u79 {
+		compatible = "iio-hwmon";
+		io-channels = <&u79 0>, <&u79 1>, <&u79 2>, <&u79 3>;
+	};
+	ina226-u82 {
+		compatible = "iio-hwmon";
+		io-channels = <&u82 0>, <&u82 1>, <&u82 2>, <&u82 3>;
+	};
+	ina226-u84 {
+		compatible = "iio-hwmon";
+		io-channels = <&u84 0>, <&u84 1>, <&u84 2>, <&u84 3>;
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&gem0 { /* eth MDIO 76/77 */
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	is-internal-pcspma;
+	phy0: ethernet-phy@0 { /* marwell m88e1512 */
+		reg = <0>;
+		reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+/*		xlnx,phy-type = <PHY_TYPE_SGMII>; */
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "", "", "", "", "", /* 0 - 4 */
+		  "", "", "", "", "", /* 5 - 9 */
+		  "", "", "", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "", "", "", "", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "", "", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "", "", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "", "", "", "", "", /* 45 - 49 */
+		  "", "", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */
+		  "", "", "", "", "", /* 65 - 69 */
+		  "", "", "", "", "", /* 70 - 74 */
+		  "", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "SYSCTLR_VERSAL_MODE0", "SYSCTLR_VERSAL_MODE1", /* 78 - 79 */
+		  "SYSCTLR_VERSAL_MODE2", "SYSCTLR_VERSAL_MODE3", "SYSCTLR_POR_B_LS", "DC_PRSNT", "SYSCTLR_POWER_EN", /* 80 - 84 */
+		  "SYSCTLR_JTAG_S0", "SYSCTLR_JTAG_S1", "SYSCTLR_IIC_MUX0_RESET_B", "SYSCTLR_IIC_MUX1_RESET_B", "SYSCTLR_LP_I2C_SM_ALERT", /* 85 -89 */
+		  "SYSCTLR_GPIO0", "SYSCTLR_GPIO1", "SYSCTLR_GPIO2", "SYSCTLR_GPIO3", "SYSCTLR_GPIO4", /* 90 - 94 */
+		  "SYSCTLR_GPIO5", "VCCO_500_RBIAS", "VCCO_501_RBIAS", "VCCO_502_RBIAS", "VCCO_500_RBIAS_LED", /* 95 - 99 */
+		  "VCCO_501_RBIAS_LED", "VCCO_502_RBIAS_LED", "SYSCTLR_VCCINT_EN", "SYSCTLR_VCC_IO_SOC_EN", "SYSCTLR_VCC_PMC_EN", /* 100 - 104 */
+		  "SYSCTLR_VCC_RAM_EN", "SYSCTLR_VCC_PSLP_EN", "SYSCTLR_VCC_PSFP_EN", "SYSCTLR_VCCAUX_EN", "SYSCTLR_VCCAUX_PMC_EN", /* 105 - 109 */
+		  "SYSCTLR_VCCO_500_EN", "SYSCTLR_VCCO_501_EN", "SYSCTLR_VCCO_502_EN", "SYSCTLR_VCCO_503_EN", "SYSCTLR_VCC1V8_EN", /* 110 - 114 */
+		  "SYSCTLR_VCC3V3_EN", "SYSCTLR_VCC1V2_DDR4_EN", "SYSCTLR_VCC1V1_LP4_EN", "SYSCTLR_VDD1_1V8_LP4_EN", "SYSCTLR_VADJ_FMC_EN", /* 115 - 119 */
+		  "SYSCTLR_MGTYAVCC_EN", "SYSCTLR_MGTYAVTT_EN", "SYSCTLR_MGTYVCCAUX_EN", "SYSCTLR_UTIL_1V13_EN", "SYSCTLR_UTIL_1V8_EN", /* 120 - 124 */
+		  "SYSCTLR_UTIL_2V5_EN", "FMCP1_FMC_PRSNT_M2C_B", "FMCP2_FMC_PRSNT_M2C_B", "FMCP1_FMCP_PRSNT_M2C_B", "FMCP2_FMCP_PRSNT_M2C_B", /* 125 - 129 */
+		  "PMBUS1_INA226_ALERT", "PMBUS2_INA226_ALERT", "SYSCTLR_USBC_SBU1", "SYSCTLR_USBC_SBU2", "TI_CABLE1", /* 130 - 134 */
+		  "TI_CABLE2", "SYSCTLR_MIC2005_EN_B", "SYSCTLR_MIC2005_FAULT_B", "SYSCTLR_TUSB320_INT_B", "SYSCTLR_TUSB320_ID", /* 135 - 139 */
+		  "PMBUS1_ALERT", "PMBUS2_ALERT", "SYSCTLR_ETH_RESET_B", "SYSCTLR_VCC0V85_TG", "MAX6643_OT_B", /* 140 - 144 */
+		  "MAX6643_FANFINAL_B", "MAX6643_FULLSPD", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio 34 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+	i2c-mux@74 { /* u94 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@50 { /* u96 - 24LC32A - 256B */
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+		i2c@1 { /* CM_I2C_SCL - Samtec */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c@2 { /* PMBUS - AFX_PMBUS */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			tps544@d { /* u85 */
+				compatible = "ti,tps544b25";
+				reg = <0xd>;
+			};
+			tps544@10 { /* u73 */
+				compatible = "ti,tps544b25";
+				reg = <0x10>;
+			};
+			tps544@11 { /* u76 */
+				compatible = "ti,tps544b25";
+				reg = <0x11>;
+			};
+			tps544@12 { /* u77 */
+				compatible = "ti,tps544b25";
+				reg = <0x12>;
+			};
+			tps544@13 { /* u80 */
+				compatible = "ti,tps544b25";
+				reg = <0x13>;
+			};
+			tps544@14 { /* u81 */
+				compatible = "ti,tps544b25";
+				reg = <0x14>;
+			};
+			tps544@15 { /* u83 */
+				compatible = "ti,tps544b25";
+				reg = <0x15>;
+			};
+			tps544@16 { /* u63 */
+				compatible = "ti,tps544b25";
+				reg = <0x16>;
+			};
+			tps544@17 { /* u66 */
+				compatible = "ti,tps544b25";
+				reg = <0x17>;
+			};
+			tps544@18 { /* u67 */
+				compatible = "ti,tps544b25";
+				reg = <0x18>;
+			};
+			tps544@19 { /* u69 */
+				compatible = "ti,tps544b25";
+				reg = <0x19>;
+			};
+			tps544@1d { /* u88 */
+				compatible = "ti,tps544b25";
+				reg = <0x1d>;
+			};
+			tps544@1e { /* u89 */
+				compatible = "ti,tps544b25";
+				reg = <0x1e>;
+			};
+			tps544@1f { /* u87 */
+				compatible = "ti,tps544b25";
+				reg = <0x1f>;
+			};
+			tps544@20 { /* u71 */
+				compatible = "ti,tps544b25";
+				reg = <0x20>;
+			};
+			u74: ina226@40 { /* u74 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u74";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+			u75: ina226@41 { /* u75 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u75";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+			u78: ina226@42 { /* u78 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u78";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			u79: ina226@43 { /* u79 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u79";
+				reg = <0x43>;
+				shunt-resistor = <1000>;
+			};
+			u82: ina226@44 { /* u82 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u82";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+			u84: ina226@45 { /* u84 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u84";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			tps53681@c0 { /* u53 - FIXME name - don't know what it does - also vcc_io_soc */
+				compatible = "ti,tps53681", "ti,tps53679";
+				reg = <0xc0>;
+			};
+		};
+		i2c@3 { /* fmc1 via JA2G */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom_fmc1: eeprom@50 { /* on FMC */
+				compatible = "atmel,24c04";
+				reg = <0x50>;
+			};
+		};
+		i2c@4 { /* fmc2 via JA3G */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			eeprom_fmc2: eeprom@50 { /* on FMC */
+				compatible = "atmel,24c04";
+				reg = <0x50>;
+			};
+		};
+		i2c@5 { /* fmc3 via JA4G */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			eeprom_fmc3: eeprom@50 { /* on FMC */
+				compatible = "atmel,24c04";
+				reg = <0x50>;
+			};
+		};
+		i2c@6 { /* ddr dimm */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+		/* 7 unused */
+	};
+};
+
+&usb0 { /* USB0 MIO52-63 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	maximum-speed = "high-speed";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-m-a2197-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-m-a2197-01-revA.dts
@@ -0,0 +1,488 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Versal System Controller on a2197 Memory Char board RevA";
+	compatible = "xlnx,zynqmp-m-a2197-01-revA", "xlnx,zynqmp-a2197-revA",
+		     "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>; /* FIXME don't know how big memory is there */
+	};
+
+	ina226-vcc-aux {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_aux 0>, <&vcc_aux 1>, <&vcc_aux 2>, <&vcc_aux 3>;
+	};
+	ina226-vcc-ram {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_ram 0>, <&vcc_ram 1>, <&vcc_ram 2>, <&vcc_ram 3>;
+	};
+	ina226-vcc1v1-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v1_lp4 0>, <&vcc1v1_lp4 1>, <&vcc1v1_lp4 2>, <&vcc1v1_lp4 3>;
+	};
+	ina226-vcc1v2-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2_lp4 0>, <&vcc1v2_lp4 1>, <&vcc1v2_lp4 2>, <&vcc1v2_lp4 3>;
+	};
+	ina226-vdd1-1v8-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vdd1_1v8_lp4 0>, <&vdd1_1v8_lp4 1>, <&vdd1_1v8_lp4 2>, <&vdd1_1v8_lp4 3>;
+	};
+	ina226-vcc0v6-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc0v6_lp4 0>, <&vcc0v6_lp4 1>, <&vcc0v6_lp4 2>, <&vcc0v6_lp4 3>;
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings  16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>; /* FIXME tap delay */
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&uart1 { /* uart1 MIO40-41 */
+	status = "okay";
+};
+
+&sdhci1 { /* sd1 MIO45-51 cd in place */
+	status = "disable";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii"; /* DTG generates this properly  1512 */
+	phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>;
+	phy0: ethernet-phy@0 { /* marwell m88e1512 - SGMII */
+		reg = <0>;
+/*		xlnx,phy-type = <PHY_TYPE_SGMII>; */
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "SCLK_OUT", "MISO_MO1", "MO2", "MO3", "MOSI_MIO0", /* 0 - 4 */
+		  "N_SS_OUT", "", "SYS_CTRL0", "SYS_CTRL1", "SYS_CTRL2", /* 5 - 9 */
+		  "SYS_CTRL3", "SYS_CTRL4", "SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "RXD0_IN", "TXD0_OUT", "TXD1_OUT", "RXD1_IN", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */
+		  "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */
+		  "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */
+		  "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", "", "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* u46 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */
+		i2c@0 { /* PMBUS  must be enabled via SW21 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			reg_vcc1v2_lp4: tps544@15 { /* u97 */
+				compatible = "ti,tps544b25";
+				reg = <0x15>;
+			};
+			reg_vcc1v1_lp4: tps544@16 { /* u95 */
+				compatible = "ti,tps544b25";
+				reg = <0x16>;
+			};
+			reg_vdd1_1v8_lp4: tps544@17 { /* u99 */
+				compatible = "ti,tps544b25";
+				reg = <0x17>;
+			};
+			/* UTIL_PMBUS connection */
+			reg_vcc1v8: tps544@13 { /* u92 */
+				compatible = "ti,tps544b25";
+				reg = <0x13>;
+			};
+			reg_vcc3v3: tps544@14 { /* u93 */
+				compatible = "ti,tps544b25";
+				reg = <0x14>;
+			};
+			reg_vcc5v0: tps544@1e { /* u94 */
+				compatible = "ti,tps544b25";
+				reg = <0x1e>;
+			};
+		};
+		i2c@1 { /* PMBUS_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			vcc_aux: ina226@42 { /* u86 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-aux";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc_ram: ina226@43 { /* u81 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-ram";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v1_lp4: ina226@46 { /* u96 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v1-lp4";
+				reg = <0x46>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v2_lp4: ina226@47 { /* u98 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2-lp4";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			vdd1_1v8_lp4: ina226@48 { /* u100 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vdd1-1v8-lp4";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vcc0v6_lp4: ina226@49 { /* u101 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc0v6-lp4";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 { /* PMBUS1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			reg_vccint: tps53681@c0 { /* u69 */
+				compatible = "ti,tps53681", "ti,tps53679";
+				reg = <0xc0>;
+			};
+			reg_vcc_pmc: tps544@7 { /* u80 */
+				compatible = "ti,tps544b25";
+				reg = <0x7>;
+			};
+			reg_vcc_ram: tps544@8 { /* u82 */
+				compatible = "ti,tps544b25";
+				reg = <0x8>;
+			};
+			reg_vcc_pslp: tps544@9 { /* u83 */
+				compatible = "ti,tps544b25";
+				reg = <0x9>;
+			};
+			reg_vcc_psfp: tps544@a { /* u84 */
+				compatible = "ti,tps544b25";
+				reg = <0xa>;
+			};
+			reg_vccaux: tps544@d { /* u85 */
+				compatible = "ti,tps544b25";
+				reg = <0xd>;
+			};
+			reg_vccaux_pmc: tps544@e { /* u87 */
+				compatible = "ti,tps544b25";
+				reg = <0xe>;
+			};
+			reg_vcco_500: tps544@f { /* u88 */
+				compatible = "ti,tps544b25";
+				reg = <0xf>;
+			};
+			reg_vcco_501: tps544@10 { /* u89 */
+				compatible = "ti,tps544b25";
+				reg = <0x10>;
+			};
+			reg_vcco_502: tps544@11 { /* u90 */
+				compatible = "ti,tps544b25";
+				reg = <0x11>;
+			};
+			reg_vcco_503: tps544@12 { /* u91 */
+				compatible = "ti,tps544b25";
+				reg = <0x12>;
+			};
+		};
+		i2c@3 { /* MEM PMBUS - FIXME bug in schematics */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* reg = <3>; */
+		};
+		i2c@4 { /* LP_I2C_SM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* connected to U20G */
+		};
+		/* 5-7 unused */
+	};
+};
+
+/* TODO sysctrl via J239 */
+/* TODO samtec J212G/H via J242 */
+/* TODO teensy via U30 PCA9543A bus 1 */
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Must be enabled via J242 */
+	eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	i2c-mux@74 { /* u47 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX1_RESET */
+		dc_i2c: i2c@0 { /* DC_I2C */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u51 - m24128 16kB FIXME addr */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+			};
+			si570_ref_clk: clock-generator@5d { /* u26 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>; /* FIXME addr */
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "REF_CLK"; /* FIXME */
+				silabs,skip-recall;
+			};
+			/* Connection via Samtec U20D */
+			/* Use for storing information about X-PRC card */
+			x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			/* Use for setting up certain features on X-PRC card */
+			x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+		};
+		i2c@2 { /* C0_LP4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_c0_lp4: clock-generator@55 { /* u10 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C0_LP4_SI570_CLK";
+			};
+		};
+		i2c@3 { /* C1_LP4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_c1_lp4: clock-generator@5d { /* u10 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>; /* FIXME addr */
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C1_LP4_SI570_CLK";
+			};
+		};
+		i2c@4 { /* C2_LP4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			si570_c2_lp4: clock-generator@55 { /* u10 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C2_LP4_SI570_CLK";
+			};
+		};
+		i2c@5 { /* C3_LP4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			si570_c3_lp4: clock-generator@55 { /* u15 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C3_LP4_SI570_CLK";
+			};
+		};
+		i2c@6 { /* HSDP_SI570 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			si570_hsdp: clock-generator@5d { /* u19 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>; /* FIXME addr */
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "HSDP_SI570";
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	/* dr_mode = "peripheral"; */
+	maximum-speed = "high-speed";
+};
+
+&usb1 {
+	status = "disabled"; /* not at mem board */
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_1 {
+	/delete-property/ phy-names ;
+	/delete-property/ phys ;
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk ;
+	snps,dis_u3_susphy_quirk ;
+	status = "disabled";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-m-a2197-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-m-a2197-02-revA.dts
@@ -0,0 +1,494 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Versal System Controller on a2197 Memory Char board RevA";
+	compatible = "xlnx,zynqmp-m-a2197-02-revA", "xlnx,zynqmp-a2197-revA",
+		     "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>; /* FIXME don't know how big memory is there */
+	};
+
+	ina226-vcc-aux {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_aux 0>, <&vcc_aux 1>, <&vcc_aux 2>, <&vcc_aux 3>;
+	};
+	ina226-vcc-ram {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_ram 0>, <&vcc_ram 1>, <&vcc_ram 2>, <&vcc_ram 3>;
+	};
+	ina226-vcc1v1-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v1_lp4 0>, <&vcc1v1_lp4 1>, <&vcc1v1_lp4 2>, <&vcc1v1_lp4 3>;
+	};
+	ina226-vcc1v2-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2_lp4 0>, <&vcc1v2_lp4 1>, <&vcc1v2_lp4 2>, <&vcc1v2_lp4 3>;
+	};
+	ina226-vdd1-1v8-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vdd1_1v8_lp4 0>, <&vdd1_1v8_lp4 1>, <&vdd1_1v8_lp4 2>, <&vdd1_1v8_lp4 3>;
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings  16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>; /* FIXME tap delay */
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&uart1 { /* uart1 MIO40-41 */
+	status = "okay";
+};
+
+&sdhci1 { /* sd1 MIO45-51 cd in place */
+	status = "disable";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>;
+	phy0: ethernet-phy@0 { /* marwell m88e1512 - SGMII */
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "SCLK_OUT", "MISO_MO1", "MO2", "MO3", "MOSI_MIO0", /* 0 - 4 */
+		  "N_SS_OUT", "", "SYS_CTRL0", "SYS_CTRL1", "SYS_CTRL2", /* 5 - 9 */
+		  "SYS_CTRL3", "SYS_CTRL4", "SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "RXD0_IN", "TXD0_OUT", "TXD1_OUT", "RXD1_IN", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */
+		  "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */
+		  "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */
+		  "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", "", "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* u46 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */
+		i2c@0 { /* PMBUS  must be enabled via SW21 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			reg_vcc1v2_lp4: tps544@15 { /* u97 */
+				compatible = "ti,tps544b25";
+				reg = <0x15>;
+			};
+			reg_vcc1v1_lp4: tps544@16 { /* u95 */
+				compatible = "ti,tps544b25";
+				reg = <0x16>;
+			};
+			reg_vdd1_1v8_lp4: tps544@17 { /* u99 */
+				compatible = "ti,tps544b25";
+				reg = <0x17>;
+			};
+			/* UTIL_PMBUS connection */
+			reg_vcc1v8: tps544@13 { /* u92 */
+				compatible = "ti,tps544b25";
+				reg = <0x13>;
+			};
+			reg_vcc3v3: tps544@14 { /* u93 */
+				compatible = "ti,tps544b25";
+				reg = <0x14>;
+			};
+			reg_vcc5v0: tps544@1e { /* u94 */
+				compatible = "ti,tps544b25";
+				reg = <0x1e>;
+			};
+			reg_vpp_2v5_ddr4: tps544@1x { /* u3007 */
+				compatible = "ti,tps544b25";
+				reg = <0x17>; /* FIXME wrong in schematics */
+			};
+		};
+		i2c@1 { /* PMBUS_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			vcc_aux: ina226@42 { /* u86 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-aux";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc_ram: ina226@43 { /* u81 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-ram";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v1_lp4: ina226@46 { /* u96 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v1-lp4";
+				reg = <0x46>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v2_lp4: ina226@47 { /* u98 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2-lp4";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			vdd1_1v8_lp4: ina226@48 { /* u100 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vdd1-1v8-lp4";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 { /* PMBUS1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			reg_vccint: tps53681@c0 { /* u69 */
+				compatible = "ti,tps53681", "ti,tps53679";
+				reg = <0xc0>;
+			};
+			reg_vcc_pmc: tps544@7 { /* u80 */
+				compatible = "ti,tps544b25";
+				reg = <0x7>;
+			};
+			reg_vcc_ram: tps544@8 { /* u82 */
+				compatible = "ti,tps544b25";
+				reg = <0x8>;
+			};
+			reg_vcc_pslp: tps544@9 { /* u83 */
+				compatible = "ti,tps544b25";
+				reg = <0x9>;
+			};
+			reg_vcc_psfp: tps544@a { /* u84 */
+				compatible = "ti,tps544b25";
+				reg = <0xa>;
+			};
+			reg_vccaux: tps544@d { /* u85 */
+				compatible = "ti,tps544b25";
+				reg = <0xd>;
+			};
+			reg_vccaux_pmc: tps544@e { /* u87 */
+				compatible = "ti,tps544b25";
+				reg = <0xe>;
+			};
+			reg_vcco_500: tps544@f { /* u88 */
+				compatible = "ti,tps544b25";
+				reg = <0xf>;
+			};
+			reg_vcco_501: tps544@10 { /* u89 */
+				compatible = "ti,tps544b25";
+				reg = <0x10>;
+			};
+			reg_vcco_502: tps544@11 { /* u90 */
+				compatible = "ti,tps544b25";
+				reg = <0x11>;
+			};
+			reg_vcco_503: tps544@12 { /* u91 */
+				compatible = "ti,tps544b25";
+				reg = <0x12>;
+			};
+		};
+		i2c@3 { /* MEM PMBUS - FIXME bug in schematics */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* reg = <3>; */
+		};
+		i2c@4 { /* LP_I2C_SM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* connected to U20G */
+		};
+		i2c@5 { /* C0_DDR4_RDIMM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+		i2c@6 { /* C2_DDR5_RDIMM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+		i2c@7 { /* C3_DDR4_UDIMM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* TODO sysctrl via J239 */
+/* TODO samtec J212G/H via J242 */
+/* TODO teensy via U30 PCA9543A bus 1 */
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Must be enabled via J242 */
+	eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	i2c-mux@74 { /* u47 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX1_RESET */
+		dc_i2c: i2c@0 { /* DC_I2C */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u51 - m24128 16kB FIXME addr */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+			};
+			si570_ref_clk: clock-generator@5d { /* u26 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>; /* FIXME addr */
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "REF_CLK"; /* FIXME */
+				silabs,skip-recall;
+			};
+			/* Connection via Samtec U20D */
+			/* Use for storing information about X-PRC card */
+			x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			/* Use for setting up certain features on X-PRC card */
+			x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+		};
+		i2c@2 { /* C0_DDR4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_c0_ddr4: clock-generator@55 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C0_DD4_SI570_CLK";
+			};
+		};
+		i2c@3 { /* C1_RLD3 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_c1_lp4: clock-generator@55 { /* u7 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C1_RLD3_SI570_CLK";
+			};
+		};
+		i2c@4 { /* C2_DDR5 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			si570_c2_lp4: clock-generator@55 { /* u10 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C2_DDR5_SI570_CLK";
+			};
+		};
+		i2c@5 { /* C3_DDR4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			si570_c3_lp4: clock-generator@55 { /* u15 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C3_LP4_SI570_CLK";
+			};
+		};
+		i2c@6 { /* HSDP_SI570 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			si570_hsdp: clock-generator@5d { /* u19 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "HSDP_SI570";
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	/* dr_mode = "peripheral"; */
+	maximum-speed = "high-speed";
+};
+
+&usb1 {
+	status = "disabled"; /* not at mem board */
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_1 {
+	/delete-property/ phy-names ;
+	/delete-property/ phys ;
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk ;
+	snps,dis_u3_susphy_quirk ;
+	status = "disabled";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-m-a2197-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-m-a2197-03-revA.dts
@@ -0,0 +1,484 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Versal System Controller on a2197 Memory Char board RevA";
+	compatible = "xlnx,zynqmp-m-a2197-03-revA", "xlnx,zynqmp-a2197-revA",
+		     "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>; /* FIXME don't know how big memory is there */
+	};
+
+	ina226-vcc-aux {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_aux 0>, <&vcc_aux 1>, <&vcc_aux 2>, <&vcc_aux 3>;
+	};
+	ina226-vcc-ram {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc_ram 0>, <&vcc_ram 1>, <&vcc_ram 2>, <&vcc_ram 3>;
+	};
+	ina226-vcc1v1-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v1_lp4 0>, <&vcc1v1_lp4 1>, <&vcc1v1_lp4 2>, <&vcc1v1_lp4 3>;
+	};
+	ina226-vcc1v2-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2_lp4 0>, <&vcc1v2_lp4 1>, <&vcc1v2_lp4 2>, <&vcc1v2_lp4 3>;
+	};
+	ina226-vdd1-1v8-lp4 {
+		compatible = "iio-hwmon";
+		io-channels = <&vdd1_1v8_lp4 0>, <&vdd1_1v8_lp4 1>, <&vdd1_1v8_lp4 2>, <&vdd1_1v8_lp4 3>;
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings  16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>; /* FIXME tap delay */
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&uart1 { /* uart1 MIO40-41 */
+	status = "okay";
+};
+
+&sdhci1 { /* sd1 MIO45-51 cd in place */
+	status = "disable";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>;
+	phy0: ethernet-phy@0 { /* marwell m88e1512 - SGMII */
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "SCLK_OUT", "MISO_MO1", "MO2", "MO3", "MOSI_MIO0", /* 0 - 4 */
+		  "N_SS_OUT", "", "SYS_CTRL0", "SYS_CTRL1", "SYS_CTRL2", /* 5 - 9 */
+		  "SYS_CTRL3", "SYS_CTRL4", "SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "RXD0_IN", "TXD0_OUT", "TXD1_OUT", "RXD1_IN", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */
+		  "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */
+		  "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */
+		  "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", "", "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* u46 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */
+		i2c@0 { /* PMBUS  must be enabled via SW21 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			reg_vcc1v2_lp4: tps544@15 { /* u97 */
+				compatible = "ti,tps544b25";
+				reg = <0x15>;
+			};
+			reg_vcc1v1_lp4: tps544@16 { /* u95 */
+				compatible = "ti,tps544b25";
+				reg = <0x16>;
+			};
+			reg_vdd1_1v8_lp4: tps544@17 { /* u99 */
+				compatible = "ti,tps544b25";
+				reg = <0x17>;
+			};
+			/* UTIL_PMBUS connection */
+			reg_vcc1v8: tps544@13 { /* u92 */
+				compatible = "ti,tps544b25";
+				reg = <0x13>;
+			};
+			reg_vcc3v3: tps544@14 { /* u93 */
+				compatible = "ti,tps544b25";
+				reg = <0x14>;
+			};
+			reg_vcc5v0: tps544@1e { /* u94 */
+				compatible = "ti,tps544b25";
+				reg = <0x1e>;
+			};
+			reg_vpp_2v5_ddr4: tps544@1x { /* u3007 */
+				compatible = "ti,tps544b25";
+				reg = <0x17>; /* FIXME wrong in schematics */
+			};
+		};
+		i2c@1 { /* PMBUS_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			vcc_aux: ina226@42 { /* u86 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-aux";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc_ram: ina226@43 { /* u81 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc-ram";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v1_lp4: ina226@46 { /* u96 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v1-lp4";
+				reg = <0x46>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v2_lp4: ina226@47 { /* u98 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2-lp4";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			vdd1_1v8_lp4: ina226@48 { /* u100 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vdd1-1v8-lp4";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 { /* PMBUS1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			reg_vccint: tps53681@c0 { /* u69 */
+				compatible = "ti,tps53681", "ti,tps53679";
+				reg = <0xc0>;
+			};
+			reg_vcc_pmc: tps544@7 { /* u80 */
+				compatible = "ti,tps544b25";
+				reg = <0x7>;
+			};
+			reg_vcc_ram: tps544@8 { /* u82 */
+				compatible = "ti,tps544b25";
+				reg = <0x8>;
+			};
+			reg_vcc_pslp: tps544@9 { /* u83 */
+				compatible = "ti,tps544b25";
+				reg = <0x9>;
+			};
+			reg_vcc_psfp: tps544@a { /* u84 */
+				compatible = "ti,tps544b25";
+				reg = <0xa>;
+			};
+			reg_vccaux: tps544@d { /* u85 */
+				compatible = "ti,tps544b25";
+				reg = <0xd>;
+			};
+			reg_vccaux_pmc: tps544@e { /* u87 */
+				compatible = "ti,tps544b25";
+				reg = <0xe>;
+			};
+			reg_vcco_500: tps544@f { /* u88 */
+				compatible = "ti,tps544b25";
+				reg = <0xf>;
+			};
+			reg_vcco_501: tps544@10 { /* u89 */
+				compatible = "ti,tps544b25";
+				reg = <0x10>;
+			};
+			reg_vcco_502: tps544@11 { /* u90 */
+				compatible = "ti,tps544b25";
+				reg = <0x11>;
+			};
+			reg_vcco_503: tps544@12 { /* u91 */
+				compatible = "ti,tps544b25";
+				reg = <0x12>;
+			};
+		};
+		i2c@3 { /* MEM PMBUS - FIXME bug in schematics */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* reg = <3>; */
+		};
+		i2c@4 { /* LP_I2C_SM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* connected to U20G */
+		};
+		i2c@5 { /* DDR4_SODIMM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+	};
+};
+
+/* TODO sysctrl via J239 */
+/* TODO samtec J212G/H via J242 */
+/* TODO teensy via U30 PCA9543A bus 1 */
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Must be enabled via J242 */
+	eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	i2c-mux@74 { /* u47 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset connected to SYSCTRL_IIC_MUX1_RESET */
+		dc_i2c: i2c@0 { /* DC_I2C */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u51 - m24128 16kB FIXME addr */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+			};
+			si570_ref_clk: clock-generator@5d { /* u26 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>; /* FIXME addr */
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "REF_CLK"; /* FIXME */
+				silabs,skip-recall;
+			};
+			/* Connection via Samtec U20D */
+			/* Use for storing information about X-PRC card */
+			x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			/* Use for setting up certain features on X-PRC card */
+			x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+		};
+		i2c@2 { /* C0_DDR4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_c0_ddr4: clock-generator@55 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C0_DD4_SI570_CLK";
+			};
+		};
+		i2c@3 { /* C1_SODIMM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_c1_lp4: clock-generator@55 { /* u7 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C1_SODIMM_SI570_CLK";
+			};
+		};
+		i2c@4 { /* C2_QDRIV */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			si570_c2_lp4: clock-generator@55 { /* u10 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C2_QDRIV_SI570_CLK";
+			};
+		};
+		i2c@5 { /* C3_DDR4 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			si570_c3_lp4: clock-generator@55 { /* u15 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x55>;
+				temperature-stability = <50>;
+				factory-fout = <30000000>;
+				clock-frequency = <30000000>;
+				clock-output-names = "C3_LP4_SI570_CLK";
+			};
+		};
+		i2c@6 { /* HSDP_SI570 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			si570_hsdp: clock-generator@5d { /* u19 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "HSDP_SI570";
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	/* dr_mode = "peripheral"; */
+	maximum-speed = "high-speed";
+};
+
+&usb1 {
+	status = "disabled"; /* not at mem board */
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_1 {
+	/delete-property/ phy-names ;
+	/delete-property/ phys ;
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk ;
+	snps,dis_u3_susphy_quirk ;
+	status = "disabled";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-01-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-01-revA.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP System Controller X-PRC-01 revA (SE1)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,zynqmp-x-prc-01-revA", "xlnx,zynqmp-x-prc-01";
+
+	fragment@0 {
+		target = <&dc_i2c>;
+
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			x_prc_eeprom: eeprom@52 { /* u120 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			x_prc_tca9534: gpio@22 { /* u121 tca9534 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>; /* Must be enabled via J242 */
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom_versal: eeprom@51 { /* u116 */
+				compatible = "atmel,24c02";
+				reg = <0x51>;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-02-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-02-revA.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP System Controller X-PRC-02 revA (SE2)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,zynqmp-x-prc-02-revA", "xlnx,zynqmp-x-prc-02";
+
+	fragment@0 {
+		target = <&dc_i2c>;
+
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			x_prc_eeprom: eeprom@52 { /* u16 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			x_prc_tca9534: gpio@22 { /* u17 tca9534 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>; /* Must be enabled via J242 */
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom_versal: eeprom@51 { /* u12 */
+				compatible = "atmel,24c02";
+				reg = <0x51>;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-03-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-03-revA.dts
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP System Controller X-PRC-03 revA (SE3)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,zynqmp-x-prc-03-revA", "xlnx,zynqmp-x-prc-03";
+
+	fragment@0 {
+		target = <&dc_i2c>;
+
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			x_prc_eeprom: eeprom@52 { /* u1 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			x_prc_tca9534: gpio@22 { /* u3 tca9534 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+			x_prc_si5338: clock-generator@70 { /* U9 */
+				compatible = "silabs,si5338";
+				reg = <0x70>; /* FIXME */
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>; /* Must be enabled via J90/J91 */
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom_versal: eeprom@51 { /* u2 */
+				compatible = "atmel,24c02";
+				reg = <0x51>;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-04-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-04-revA.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP System Controller X-PRC-04 revA (SE4)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,zynqmp-x-prc-04-revA", "xlnx,zynqmp-x-prc-04";
+
+	fragment@0 {
+		target = <&dc_i2c>;
+
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			x_prc_eeprom: eeprom@52 { /* u120 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			x_prc_tca9534: gpio@22 { /* u121 tca9534 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+
+			si570_gem_tsu: clock-generator@5d { /* u164 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>; /* FIXME */
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_gem_tsu_clk";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom_versal: eeprom@51 { /* u153 */
+				compatible = "atmel,24c02";
+				reg = <0x51>;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-05-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA-x-prc-05-revA.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP System Controller X-PRC-05 revA (SE5)
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "xlnx,zynqmp-x-prc-05-revA", "xlnx,zynqmp-x-prc-05";
+
+	fragment@0 {
+		target = <&dc_i2c>;
+
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			x_prc_eeprom: eeprom@52 { /* u120 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			x_prc_tca9534: gpio@22 { /* u121 tca9534 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+
+			si570_gem_tsu: clock-generator@5d { /* u164 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>; /* FIXME */
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_gem_tsu_clk";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom_versal: eeprom@51 { /* u153 */
+				compatible = "atmel,24c02";
+				reg = <0x51>;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-p-a2197-00-revA.dts
@@ -0,0 +1,616 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx Versal a2197 RevA System Controller
+ *
+ * (C) Copyright 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "Versal System Controller on a2197 Processor Char board RevA"; /* Tenzing */
+	compatible = "xlnx,zynqmp-p-a2197-00-revA", "xlnx,zynqmp-a2197-revA",
+		     "xlnx,zynqmp-a2197", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		usb0 = &usb0;
+		usb1 = &usb1;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ref_clk: ref_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_ref_clk>;
+	};
+
+	ddr4_dimm1_si570: ddr4_dimm1_si570 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_ddr_dimm1>;
+	};
+
+	ddr4_dimm2_si570: ddr4_dimm2_si570 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_ddr_dimm2>;
+	};
+
+	lpddr4_si570: lpddr4_si570 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_lpddr4>;
+	};
+
+	hsdp_si570: hsdp_si570 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&si570_hsdp>;
+	};
+
+	si5332_1: si5332_1 { /* clk0_sgmii - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	si5332_2: si5332_2 { /* clk1_usb - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings  16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+};
+
+&uart1 { /* uart1 MIO40-41 */
+	status = "okay";
+};
+
+&sdhci1 { /* sd1 MIO45-51 cd in place */
+	status = "okay";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+&psgtr {
+	status = "okay";
+	/* sgmii, usb3 */
+	clocks = <&si5332_1>, <&si5332_2>;
+	clock-names = "ref0", "ref1";
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii"; /* DTG generates this properly  1512 */
+	is-internal-pcspma;
+	/* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "", "", "", "", "", /* 0 - 4 */
+		  "", "", "DC_SYS_CTRL0", "DC_SYS_CTRL1", "DC_SYS_CTRL2", /* 5 - 9 */
+		  "DC_SYS_CTRL3", "DC_SYS_CTRL4", "DC_SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "", "", "", "", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */
+		  "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */
+		  "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */
+		  "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "SYSCTLR_VERSAL_MODE0", "SYSCTLR_VERSAL_MODE1", /* 78 - 79 */
+		  "SYSCTLR_VERSAL_MODE2", "SYSCTLR_VERSAL_MODE3", "SYSCTLR_POR_B_LS", "DC_PRSNT", "SYSCTLR_POWER_EN", /* 80 - 84 */
+		  "SYSCTLR_JTAG_S0", "SYSCTLR_JTAG_S1", "SYSCTLR_IIC_MUX0_RESET_B", "SYSCTLR_IIC_MUX1_RESET_B", "SYSCTLR_LP_I2C_SM_ALERT", /* 85 -89 */
+		  "SYSCTLR_GPIO0", "SYSCTLR_GPIO1", "SYSCTLR_GPIO2", "SYSCTLR_GPIO3", "SYSCTLR_GPIO4", /* 90 - 94 */
+		  "SYSCTLR_GPIO5", "VCCO_500_RBIAS", "VCCO_501_RBIAS", "VCCO_502_RBIAS", "VCCO_500_RBIAS_LED", /* 95 - 99 */
+		  "VCCO_501_RBIAS_LED", "VCCO_502_RBIAS_LED", "SYSCTLR_VCCINT_EN", "SYSCTLR_VCC_IO_SOC_EN", "SYSCTLR_VCC_PMC_EN", /* 100 - 104 */
+		  "SYSCTLR_VCC_RAM_EN", "SYSCTLR_VCC_PSLP_EN", "SYSCTLR_VCC_PSFP_EN", "SYSCTLR_VCCAUX_EN", "SYSCTLR_VCCAUX_PMC_EN", /* 105 - 109 */
+		  "SYSCTLR_VCCO_500_EN", "SYSCTLR_VCCO_501_EN", "SYSCTLR_VCCO_502_EN", "SYSCTLR_VCCO_503_EN", "SYSCTLR_VCC1V8_EN", /* 110 - 114 */
+		  "SYSCTLR_VCC3V3_EN", "SYSCTLR_VCC1V2_DDR4_EN", "SYSCTLR_VCC1V1_LP4_EN", "SYSCTLR_VDD1_1V8_LP4_EN", "SYSCTLR_VADJ_FMC_EN", /* 115 - 119 */
+		  "SYSCTLR_MGTYAVCC_EN", "SYSCTLR_MGTYAVTT_EN", "SYSCTLR_MGTYVCCAUX_EN", "SYSCTLR_UTIL_1V13_EN", "SYSCTLR_UTIL_1V8_EN", /* 120 - 124 */
+		  "SYSCTLR_UTIL_2V5_EN", "FMCP1_FMC_PRSNT_M2C_B", "FMCP2_FMC_PRSNT_M2C_B", "FMCP1_FMCP_PRSNT_M2C_B", "FMCP2_FMCP_PRSNT_M2C_B", /* 125 - 129 */
+		  "PMBUS1_INA226_ALERT", "PMBUS2_INA226_ALERT", "SYSCTLR_USBC_SBU1", "SYSCTLR_USBC_SBU2", "TI_CABLE1", /* 130 - 134 */
+		  "TI_CABLE2", "SYSCTLR_MIC2005_EN_B", "SYSCTLR_MIC2005_FAULT_B", "SYSCTLR_TUSB320_INT_B", "SYSCTLR_TUSB320_ID", /* 135 - 139 */
+		  "PMBUS1_ALERT", "PMBUS2_ALERT", "SYSCTLR_ETH_RESET_B", "SYSCTLR_VCC0V85_TG", "MAX6643_OT_B", /* 140 - 144 */
+		  "MAX6643_FANFINAL_B", "MAX6643_FULLSPD", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	i2c-mux@74 { /* u33 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 { /* PMBUS1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* On connector J98 */
+			reg_vcc_fmc: tps544@7 { /* u80 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x7>;
+				regulator-name = "reg_vcc_fmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2600000>;
+				/* enable-gpio = <&gpio0 23 0x4>; optional */
+			};
+			reg_vcc_ram: tps544@8 { /* u83 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x8>;
+			};
+			reg_vcc_pslp: tps544@9 { /* u85 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x9>;
+			};
+			reg_vcc_psfp: tps544@a { /* u86 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0xa>;
+			};
+			reg_vccint: tps53681@60 { /* u70 - FIXME name - don't know what it does - also vcc_io_soc */
+				compatible = "ti,tps53681", "ti,tps53679";
+				reg = <0x60>;
+				/* vccint, vcc_io_soc */
+			};
+		};
+		i2c@1 { /* PMBUS1_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME check alerts coming to SC */
+			vcc_fmc: ina226@42 { /* u81 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc_ram: ina226@43 { /* u82 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcc_pslp: ina226@44 { /* u84 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>;
+			};
+			vcc_psfp: ina226@45 { /* u87 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 { /* PMBUS2 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* On connector J104 */
+			reg_vccaus: tps544@d { /* u88 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0xd>;
+			};
+			reg_vccaux_fmc: tps544@e { /* u90 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0xe>;
+			};
+			reg_vcco_500: tps544@f { /* u93 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0xf>;
+			};
+			reg_vcco_501: tps544@10 { /* u95 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x10>;
+			};
+			reg_vcco_502: tps544@11 { /* u97 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x11>;
+			};
+			reg_vcco_503: tps544@12 { /* u99 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x12>;
+			};
+			reg_vcc1v8: tps544@13 { /* u101 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x13>;
+			};
+			reg_vcc3v3: tps544@14 { /* u102 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x14>;
+			};
+			reg_vcc1v2_ddr4: tps544@15 { /* u104 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x15>;
+			};
+			reg_vcc1v1_lp4: tps544@16 { /* u106 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x16>;
+			};
+			reg_vcc1_1V8_lp4: tps544@17 { /* u108 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x17>;
+			};
+			reg_vadj_fmc: tps544@19 { /* u109 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x19>;
+			};
+			reg_mgtyavcc: tps544@1a { /* u111 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x1a>;
+			};
+			reg_mgtyavtt: tps544@1b { /* u114 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x1b>;
+			};
+			reg_mgtyvccaux: tps544@1c { /* u115 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x1c>;
+			};
+			reg_util_1v13: tps544@1d { /* u117 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x1d>;
+			};
+			reg_util_1v8: tps544@1e { /* u118 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x1e>;
+			};
+			reg_util_2v5: tps544@1f { /* u119 - FIXME name - don't know what it does */
+				compatible = "ti,tps544b25"; /* Documentation/hwmon/pmbus - wiring is missing */
+				reg = <0x1f>;
+			};
+		};
+		i2c@3 { /* PMBUS2_INA226 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FIXME check alerts coming to SC */
+			vccaux: ina226@40 { /* u89 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccaux_fmc: ina226@41 { /* u91 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcco_500: ina226@42 { /* u92 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcco_501: ina226@43 { /* u94 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcco_502: ina226@44 { /* u96 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>;
+			};
+			vcco_503: ina226@45 { /* u98 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			vcc_1v8: ina226@46 { /* u100 */
+				compatible = "ti,ina226";
+				reg = <0x46>;
+				shunt-resistor = <5000>;
+			};
+			vcc_3v3: ina226@47 { /* u103 */
+				compatible = "ti,ina226";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			vcc_1v2_ddr4: ina226@48 { /* u105 */
+				compatible = "ti,ina226";
+				reg = <0x48>;
+				shunt-resistor = <1000>;
+			};
+			vcc1v1_lp4: ina226@49 { /* u107 */
+				compatible = "ti,ina226";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+			vadj_fmc: ina226@4a { /* u110 */
+				compatible = "ti,ina226";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			mgtyavcc: ina226@4b { /* u112 */
+				compatible = "ti,ina226";
+				reg = <0x4b>;
+				shunt-resistor = <1000>;
+			};
+			mgtyavtt: ina226@4c { /* u113 */
+				compatible = "ti,ina226";
+				reg = <0x4c>;
+				shunt-resistor = <1000>;
+			};
+			mgtyvccaux: ina226@4d { /* u116 */
+				compatible = "ti,ina226";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+			vcc_bat: ina226@4e { /* u12 */
+				compatible = "ti,ina226";
+				reg = <0x4e>;
+				shunt-resistor = <10000000>; /* 10 ohm */
+			};
+		};
+		i2c@4 { /* LP_I2C_SM */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* connected to J212G */
+			/* zynqmp sm alert or samtec J212H */
+		};
+		/* 5-7 unused */
+	};
+};
+
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Must be enabled via J242 */
+	eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	i2c-mux@74 { /* u35 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		dc_i2c: i2c@0 { /* DC_I2C */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u34 - m24128 16kB */
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x54>;
+			};
+			si570_ref_clk: clock-generator@5d { /* u32 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;	/* 570JAC000900DG */
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "ref_clk";
+				silabs,skip-recall;
+			};
+			/* Connection via Samtec J212D */
+			/* Use for storing information about X-PRC card */
+			x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */
+				compatible = "atmel,24c02";
+				reg = <0x52>;
+			};
+
+			/* Use for setting up certain features on X-PRC card */
+			x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */
+				compatible = "nxp,pca9534";
+				reg = <0x22>;
+				gpio-controller; /* IRQ not connected */
+				#gpio-cells = <2>;
+				gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4",
+						  "", "", "", "";
+				gtr_sel0 {
+					gpio-hog;
+					gpios = <0 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_1";
+				};
+				gtr_sel1 {
+					gpio-hog;
+					gpios = <1 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_2";
+				};
+				gtr_sel2 {
+					gpio-hog;
+					gpios = <2 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_3";
+				};
+				gtr_sel3 {
+					gpio-hog;
+					gpios = <3 0>;
+					input; /* FIXME add meaning */
+					line-name = "sw4_4";
+				};
+			};
+		};
+		i2c@1 { /* FMCP1_IIC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME connection to Samtec J51C */
+			/* expected eeprom 0x50 SE cards */
+		};
+		i2c@2 { /* FMCP2_IIC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* FIXME connection to Samtec J53C */
+			/* expected eeprom 0x50 SE cards */
+		};
+		i2c@3 { /* DDR4_DIMM1 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_ddr_dimm1: clock-generator@60 { /* u2 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;	/* 570BAB000299DG */
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "si570_ddrdimm1_clk";
+			};
+			/* 0x50 SPD? */
+		};
+		i2c@4 { /* DDR4_DIMM2 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			si570_ddr_dimm2: clock-generator@60 { /* u3 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;	/* 570BAB000299DG */
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "si570_ddrdimm2_clk";
+			};
+			/* 0x50 SPD? */
+		};
+		i2c@5 { /* LPDDR4_SI570_CLK */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			si570_lpddr4: clock-generator@60 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;	/* 570BAB000299DG */
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "si570_lpddr4_clk";
+			};
+		};
+		i2c@6 { /* HSDP_SI570 */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			si570_hsdp: clock-generator@60 { /* u5 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;	/* 570JAC000900DG */
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "si570_hsdp_clk";
+			};
+		};
+		i2c@7 { /* PCIE_CLK */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* u36 0xd8 or 0xde - pcie clk buf - 9ZML1241EKILF PCIe GEN 4 CLOCK BUFFER FIXME - no driver */
+			/* u37 0xd0 DNP - pcie clocking 1 - 9FGV1006BQ505LTGI - PCIe GEN 4 CLOCK GENERATOR FIXME - no linux driver */
+			/* u38 0xca - pcie clocking 2 - 9ZML1241EKILF PCIe GEN 4 CLOCK BUFFER FIXME - no driver */
+			clock_8t49n287: clock-generator@60 { /* u39 8T49N240 - pcie clocking 3 */
+				#clock-cells = <1>; /* author David Cater <david.cater@idt.com>*/
+				compatible = "idt,8t49n240", "idt,8t49n241"; /* FIXME no driver for 240 */
+				reg = <0x60>;
+				/* Documentation/devicetree/bindings/clock/idt,idt8t49n24x.txt */
+				/* FIXME there input via J241 Samtec CLK1 and CLK0 from U38 - selection PIN */
+
+			};
+
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	maximum-speed = "super-speed";
+};
+
+&usb1 {
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+};
+
+&dwc3_1 {
+	/delete-property/ phy-names ;
+	/delete-property/ phys ;
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk ;
+	snps,dis_u3_susphy_quirk ;
+	status = "okay";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sc-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sc-revB.dts
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP Generic System Controller
+ *
+ * (C) Copyright 2021 - 2022, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP Generic System Controller";
+	compatible = "xlnx,zynqmp-sc-revB", "xlnx,zynqmp-sc", "xlnx,zynqmp";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		spi0 = &qspi;
+		spi1 = &spi0;
+		spi2 = &spi1;
+		usb0 = &usb0;
+		usb1 = &usb1;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		fwuen {
+			label = "sw16";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ds40-led {
+			label = "heartbeat";
+			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+		ds44-led {
+			label = "status";
+			gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	si5332_2: si5332_2 { /* u42 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	pwm-fan {
+		compatible = "pwm-fan";
+		status = "okay";
+		pwms = <&ttc0 2 40000 0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
+		"QSPI_CS_B", "", "LED1", "LED2", "", /* 5 - 9 */
+		"", "ZU4_TRIGGER", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		"EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		"EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "I2C1_SCL", /* 20 - 24 */
+		"I2C1_SDA", "UART0_RXD", "UART0_TXD", "", "", /* 25 - 29 */
+		"", "", "", "", "I2C0_SCL", /* 30 - 34 */
+		"I2C0_SDA", "UART1_TXD", "UART1_RXD", "GEM_TX_CLK", "GEM_TX_D0", /* 35 - 39 */
+		"GEM_TX_D1", "GEM_TX_D2", "GEM_TX_D3", "GEM_TX_CTL", "GEM_RX_CLK", /* 40 - 44 */
+		"GEM_RX_D0", "GEM_RX_D1", "GEM_RX_D2", "GEM_RX_D3", "GEM_RX_CTL", /* 45 - 49 */
+		"GEM_MDC", "GEM_MDIO", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		"USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		"USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */
+		"", "", "", "", "", /* 65 - 69 */
+		"", "", "", "", "", /* 70 - 74 */
+		"", "", "ETH_RESET_B", /* 75 - 77, MIO end and EMIO start */
+		"", "", /* 78 - 79 */
+		"", "", "", "", "", /* 80 - 84 */
+		"", "", "", "", "", /* 85 -89 */
+		"", "", "", "", "", /* 90 - 94 */
+		"", "", "", "", "", /* 95 - 99 */
+		"", "", "", "", "", /* 100 - 104 */
+		"", "", "", "", "", /* 105 - 109 */
+		"", "", "", "", "", /* 110 - 114 */
+		"", "", "", "", "", /* 115 - 119 */
+		"", "", "", "", "", /* 120 - 124 */
+		"", "", "", "", "", /* 125 - 129 */
+		"", "", "", "", "", /* 130 - 134 */
+		"", "", "", "", "", /* 135 - 139 */
+		"", "", "", "", "", /* 140 - 144 */
+		"", "", "", "", "", /* 145 - 149 */
+		"", "", "", "", "", /* 150 - 154 */
+		"", "", "", "", "", /* 155 - 159 */
+		"", "", "", "", "", /* 160 - 164 */
+		"", "", "", "", "", /* 165 - 169 */
+		"", "", "", ""; /* 170 - 174 */
+};
+
+&gem1 { /* gem1 MIO38-49, MDIO MIO50/51 */
+	status = "okay";
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy0>;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio 77 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <2>;
+
+		phy0: ethernet-phy@1 {
+			#phy-cells = <1>;
+			reg = <1>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+		};
+	};
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio 34 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+};
+
+&i2c1 { /* i2c1 MIO 24-25 */
+	status = "okay";
+	u-boot,dm-pre-reloc;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+	/* Use for storing information about SC board */
+	eeprom: eeprom@54 { /* u34 - m24128 16kB */
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x54>; /* & 0x5c */
+		u-boot,dm-pre-reloc;
+	};
+};
+
+/* USB 3.0 only */
+&psgtr {
+	status = "okay";
+	/* nc, nc, usb3 */
+	clocks = <&si5332_2>;
+	clock-names = "ref2";
+};
+
+&qspi { /* MIO 0-5 */
+	status = "okay";
+	/* QSPI should also have PINCTRL setup */
+	flash@0 {
+		compatible = "mt25qu512a", "m25p80", "jedec,spi-nor"; /* mt25qu512abb8e12 512Mib */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>; /* 40MHz */
+		partition@0 {
+			label = "Image Selector";
+			reg = <0x0 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@80000 {
+			label = "Image Selector Golden";
+			reg = <0x80000 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@100000 {
+			label = "Persistent Register";
+			reg = <0x100000 0x20000>; /* 128KB */
+		};
+		partition@120000 {
+			label = "Persistent Register Backup";
+			reg = <0x120000 0x20000>; /* 128KB */
+		};
+		partition@140000 {
+			label = "Open_1";
+			reg = <0x140000 0xC0000>; /* 768KB */
+		};
+		partition@200000 {
+			label = "Image A (FSBL, PMU, ATF, U-Boot)";
+			reg = <0x200000 0xD00000>; /* 13MB */
+		};
+		partition@f00000 {
+			label = "ImgSel Image A Catch";
+			reg = <0xF00000 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@f80000 {
+			label = "Image B (FSBL, PMU, ATF, U-Boot)";
+			reg = <0xF80000 0xD00000>; /* 13MB */
+		};
+		partition@1c80000 {
+			label = "ImgSel Image B Catch";
+			reg = <0x1C80000 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@1d00000 {
+			label = "Open_2";
+			reg = <0x1D00000 0x100000>; /* 1MB */
+		};
+		partition@1e00000 {
+			label = "Recovery Image";
+			reg = <0x1E00000 0x200000>; /* 2MB */
+			read-only;
+			lock;
+		};
+		partition@2000000 {
+			label = "Recovery Image Backup";
+			reg = <0x2000000 0x200000>; /* 2MB */
+			read-only;
+			lock;
+		};
+		partition@2200000 {
+			label = "U-Boot storage variables";
+			reg = <0x2200000 0x20000>; /* 128KB */
+		};
+		partition@2220000 {
+			label = "U-Boot storage variables backup";
+			reg = <0x2220000 0x20000>; /* 128KB */
+		};
+		partition@2240000 {
+			label = "SHA256";
+			reg = <0x2240000 0x10000>; /* 256B but 64KB sector */
+			read-only;
+			lock;
+		};
+		partition@2250000 {
+			label = "User";
+			reg = <0x2250000 0x1db0000>; /* 29.5 MB */
+		};
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings MTFC16GAPALBH 16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+};
+
+&ttc0 {
+	status = "okay";
+	#pwm-cells = <3>;
+};
+
+&uart1 { /* uart0 MIO36-37 */
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sc-vpk120-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sc-vpk120-revB.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP VPK120 revB
+ *
+ * (C) Copyright 2021 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022, Advanced Micro Devices, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/dts-v1/;
+/plugin/;
+
+
+&{/} {
+	compatible = "xlnx,zynqmp-sc-vpk120-revB", "xlnx,zynqmp-vpk120-revB",
+		     "xlnx,zynqmp-vpk120", "xlnx,zynqmp";
+
+	si570_user1_fmc_clk: si570_user1_fmc_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&user_si570_1>;
+	};
+
+	si570_ref_clk: si570_ref_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&ref_clk>;
+	};
+
+	si570_lpddr4_clk3: si570_lpddr4_clk3 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk3>;
+	};
+
+	si570_lpddr4_clk2: si570_lpddr4_clk2 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk2>;
+	};
+
+	si570_lpddr4_clk1: si570_lpddr4_clk1 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk1>;
+	};
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	tca6416_u233: gpio@20 { /* u233 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "", "", "QSFPDD1_MODSELL", "QSFPDD1_MODSELL", /* 0 - 3 */
+				"PMBUS2_INA226_ALERT", "", "", "", /* 4 - 7 */
+				"FMCP1_FMC_PRSNT_M2C_B", "", "FMCP1_FMCP_PRSNT_M2C_B", "", /* 10 - 13 */
+				"VCCINT_VRHOT_B", "8A34001_EXP_RST_B", "PMBUS_ALERT", "PMBUS1_INA226_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@74 { /* u33 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		pmbus_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* On connector J325 */
+			ir38060_41: regulator@41 { /* IR38060 - u259 */
+				compatible = "infineon,ir38060", "infineon,ir38064";
+				reg = <0x41>; /* i2c addr 0x11 */
+			};
+			ir38164_43: regulator@43 { /* IR38164 - u13 */
+				compatible = "infineon,ir38164";
+				reg = <0x43>; /* i2c addr 0x13 */
+			};
+			ir35221_46: pmic@46 { /* IR35221 - u152 */
+				compatible = "infineon,ir35221";
+				reg = <0x46>; /* i2c addr - 0x16 */
+			};
+			irps5401_47: pmic5401@47 { /* IRPS5401 - u160 */
+				compatible = "infineon,irps5401";
+				reg = <0x47>; /* i2c addr 0x17 */
+			};
+			ir38164_49: regulator@49 { /* IR38164 - u189 */
+				compatible = "infineon,ir38164";
+				reg = <0x49>; /* i2c addr 0x19 */
+			};
+			irps5401_4c: pmic@4c { /* IRPS5401 - u167 */
+				compatible = "infineon,irps5401";
+				reg = <0x4c>; /* i2c addr 0x1c */
+			};
+			irps5401_4d: pmic@4d { /* IRPS5401 - u175 */
+				compatible = "infineon,irps5401";
+				reg = <0x4d>; /* i2c addr 0x1d */
+			};
+			ir38164_4e: regulator@4e { /* IR38164 - u185 */
+				compatible = "infineon,ir38164";
+				reg = <0x4e>; /* i2c addr 0x1e */
+			};
+			ir38164_4f: regulator@4f { /* IR38164 - u187 */
+				compatible = "infineon,ir38164";
+				reg = <0x4f>; /* i2c addr 0x1f */
+			};
+		};
+		pmbus1_ina226_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME check alerts coming to SC */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vcc_soc: ina226@41 { /* u161 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc_pmc: ina226@42 { /* u163 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc_ram: ina226@43 { /* u5 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcc_pslp: ina226@44 { /* u165 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>;
+			};
+			vcc_psfp: ina226@45 { /* u164 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 { /* NC */ /* FIXME maybe remove */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		pmbus2_ina226_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FIXME check alerts coming to SC */
+			vccaux: ina226@40 { /* u166 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccaux_pmc: ina226@41 { /* u168 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@42 { /* u265 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v5: ina226@43 { /* u264 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcco_mio: ina226@45 { /* u172 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavtt: ina226@46 { /* u188 */
+				compatible = "ti,ina226";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			vcco_502: ina226@47 { /* u174 */
+				compatible = "ti,ina226";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			mgtvccaux: ina226@48 { /* u176 */
+				compatible = "ti,ina226";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v1_lp4: ina226@49 { /* u186 */
+				compatible = "ti,ina226";
+				reg = <0x49>;
+				shunt-resistor = <2000>;
+			};
+			vadj_fmc: ina226@4a { /* u184 */
+				compatible = "ti,ina226";
+				reg = <0x4a>;
+				shunt-resistor = <2000>;
+			};
+			lpdmgtyavcc: ina226@4b { /* u177 */
+				compatible = "ti,ina226";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			lpdmgtyavtt: ina226@4c { /* u260 */
+				compatible = "ti,ina226";
+				reg = <0x4c>;
+				shunt-resistor = <2000>;
+			};
+			lpdmgtyvccaux: ina226@4d { /* u234 */
+				compatible = "ti,ina226";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@4 { /* NC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+		i2c@5 { /* NC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+		user_si570: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			user_si570_1: clock-generator@5f { /* USER C0 SI570 - u205 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5f>;
+				temperature-stability = <50>;
+				factory-fout = <100000000>;
+				clock-frequency = <100000000>;
+				clock-output-names = "fmc_si570";
+				silabs,skip-recall;
+			};
+
+		};
+		/* 7 unused */
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	i2c-mux@74 { /* u35 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		ref_clk_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			ref_clk: clock-generator@5d { /* u32 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "ref_clk";
+				silabs,skip-recall;
+			};
+		};
+		fmcp1_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME connection to Samtec J51C */
+			/* expected eeprom 0x50 SE cards */
+		};
+		i2c@2 { /* NC - FIXME */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		lpddr4_si570_clk3_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			lpddr4_clk3: clock-generator@60 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk3";
+				silabs,skip-recall;
+			};
+		};
+		lpddr4_si570_clk2_i2c: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			lpddr4_clk2: clock-generator@60 { /* u3 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk2";
+				silabs,skip-recall;
+			};
+		};
+		lpddr4_si570_clk1_i2c: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			lpddr4_clk1: clock-generator@60 { /* u248 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk1";
+				silabs,skip-recall;
+			};
+		};
+		qsfpdd_i2c: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* J1/J2 connectors */
+		};
+		idt8a34001_i2c: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* Via J310 connector */
+			idt_8a34001: phc@5b {
+				compatible = "idt,8a34001"; /* u219B */
+				reg = <0x5b>; /* FIXME not in schematics */
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sc-vpk180-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sc-vpk180-revA.dts
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP VPK180 revA
+ *
+ * (C) Copyright 2021 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022, Advanced Micro Devices, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/dts-v1/;
+/plugin/;
+
+
+&{/} {
+	compatible = "xlnx,zynqmp-sc-vpk180-revA", "xlnx,zynqmp-vpk180-revA",
+		     "xlnx,zynqmp-vpk180", "xlnx,zynqmp";
+
+	si570_ref_clk: si570_ref_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&ref_clk>;
+	};
+
+	si570_lpddr4_clk3: si570_lpddr4_clk3 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk3>;
+	};
+
+	si570_lpddr4_clk2: si570_lpddr4_clk2 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk2>;
+	};
+
+	si570_lpddr4_clk1: si570_lpddr4_clk1 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk1>;
+	};
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	tca6416_u233: gpio@20 { /* u233 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "QSFPDD1_MODSELL", "QSFPDD2_MODSELL", "QSFPDD3_MODSELL", "QSFPDD4_MODSELL", /* 0 - 3 */
+				"PMBUS2_INA226_ALERT", "QSFPDD5_MODSELL", "QSFPDD6_MODSELL", "", /* 4 - 7 */
+				"FMCP1_FMC_PRSNT_M2C_B", "", "FMCP1_FMCP_PRSNT_M2C_B", "", /* 10 - 13 */
+				"VCCINT_VRHOT_B", "8A34001_EXP_RST_B", "PMBUS_ALERT", "PMBUS1_INA226_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@74 { /* u33 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		pmbus_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* On connector J325 */
+			ir38060_41: regulator@41 { /* IR38060 - u259 */
+				compatible = "infineon,ir38060", "infineon,ir38064";
+				reg = <0x41>; /* i2c addr 0x11 */
+			};
+			ir35221_45: pmic@45 { /* IR35221 - u291 */
+				compatible = "infineon,ir35221";
+				reg = <0x45>; /* i2c addr - 0x15 */
+			};
+			ir35221_46: pmic@46 { /* IR35221 - u152 */
+				compatible = "infineon,ir35221";
+				reg = <0x46>; /* i2c addr - 0x16 */
+			};
+			irps5401_47: pmic5401@47 { /* IRPS5401 - u160 */
+				compatible = "infineon,irps5401";
+				reg = <0x47>; /* i2c addr 0x17 */
+			};
+			irps5401_48: pmic@48 { /* IRPS5401 - u295 */
+				compatible = "infineon,irps5401";
+				reg = <0x48>; /* i2c addr 0x18 */
+			};
+			ir38164_49: regulator@49 { /* IR38164 - u189 */
+				compatible = "infineon,ir38164";
+				reg = <0x49>; /* i2c addr 0x19 */
+			};
+			irps5401_4c: pmic@4c { /* IRPS5401 - u167 */
+				compatible = "infineon,irps5401";
+				reg = <0x4c>; /* i2c addr 0x1c */
+			};
+			irps5401_4d: pmic@4d { /* IRPS5401 - u175 */
+				compatible = "infineon,irps5401";
+				reg = <0x4d>; /* i2c addr 0x1d */
+			};
+			ir38164_4e: regulator@4e { /* IR38164 - u185 */
+				compatible = "infineon,ir38164";
+				reg = <0x4e>; /* i2c addr 0x1e */
+			};
+			ir38164_4f: regulator@4f { /* IR38164 - u187 */
+				compatible = "infineon,ir38164";
+				reg = <0x4f>; /* i2c addr 0x1f */
+			};
+		};
+		pmbus1_ina226_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME check alerts coming to SC */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>; /* r440 */
+			};
+			vcc_soc: ina226@41 { /* u161 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>; /* r2174 */
+			};
+			vcc_pmc: ina226@42 { /* u163 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>; /* r1214 */
+			};
+			vcc_ram: ina226@43 { /* u5 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>; /* r2108 */
+			};
+			vcc_pslp: ina226@44 { /* u165 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>; /* r1830 */
+			};
+			vcc_psfp: ina226@45 { /* u164 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>; /* r2086 */
+			};
+		};
+		i2c@2 { /* NC */ /* FIXME maybe remove */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		pmbus2_ina226_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FIXME check alerts coming to SC */
+			vccaux: ina226@40 { /* u166 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <2000>; /* r2109 */
+			};
+			vccaux_pmc: ina226@41 { /* u168 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>; /* r1246 */
+			};
+			mgtavcc: ina226@42 { /* u265 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>; /* r1829 */
+			};
+			vcc1v5: ina226@43 { /* u264 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>; /* r1221 */
+			};
+			vcco_mio: ina226@45 { /* u172 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>; /* r1219 */
+			};
+			mgtavtt: ina226@46 { /* u188 */
+				compatible = "ti,ina226";
+				reg = <0x46>;
+				shunt-resistor = <2000>; /* r1384 */
+			};
+			vcco_502: ina226@47 { /* u174 */
+				compatible = "ti,ina226";
+				reg = <0x47>;
+				shunt-resistor = <5000>; /* r1825 */
+			};
+			mgtvccaux: ina226@48 { /* u176 */
+				compatible = "ti,ina226";
+				reg = <0x48>;
+				shunt-resistor = <5000>; /* r1232 */
+			};
+			vcc1v1_lp4: ina226@49 { /* u186 */
+				compatible = "ti,ina226";
+				reg = <0x49>;
+				shunt-resistor = <2000>; /* r1367 */
+			};
+			vadj_fmc: ina226@4a { /* u184 */
+				compatible = "ti,ina226";
+				reg = <0x4a>;
+				shunt-resistor = <2000>; /* r1350 */
+			};
+			lpdmgtyavcc: ina226@4b { /* u177 */
+				compatible = "ti,ina226";
+				reg = <0x4b>;
+				shunt-resistor = <5000>; /* r2097 */
+			};
+			lpdmgtyavtt: ina226@4c { /* u260 */
+				compatible = "ti,ina226";
+				reg = <0x4c>;
+				shunt-resistor = <2000>; /* r1834 */
+			};
+			lpdmgtyvccaux: ina226@4d { /* u234 */
+				compatible = "ti,ina226";
+				reg = <0x4d>;
+				shunt-resistor = <5000>; /* r1679 */
+			};
+		};
+		/* 4 - 7 unused */
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	i2c-mux@74 { /* u35 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&PL_GPIO SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		ref_clk_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			ref_clk: clock-generator@5d { /* u32 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "ref_clk";
+				silabs,skip-recall;
+			};
+		};
+		fmcp1_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* connection to Samtec J51C */
+			/* expected eeprom 0x50 SE cards */
+		};
+		osfp_i2c: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* J362 connector */
+		};
+		lpddr4_si570_clk3_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			lpddr4_clk3: clock-generator@60 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk3";
+				silabs,skip-recall;
+			};
+			/* alternative option DNP - u305 at 0x50 */
+		};
+		lpddr4_si570_clk2_i2c: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			lpddr4_clk2: clock-generator@60 { /* u3 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk2";
+				silabs,skip-recall;
+			};
+			/* alternative option DNP - u303 at 0x50 */
+		};
+		lpddr4_si570_clk1_i2c: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			lpddr4_clk1: clock-generator@60 { /* u248 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk1";
+				silabs,skip-recall;
+			};
+			/* alternative option DNP - u301 at 0x50 */
+		};
+		qsfpdd_i2c: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* J1/J2/J355/J354/J359/J358 connectors */
+		};
+		idt8a34001_i2c: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* Via J310 connector */
+			idt_8a34001: phc@5b { /* u219B */
+				compatible = "idt,8a34001";
+				reg = <0x5b>;
+			};
+		};
+	};
+	i2c-mux@75 { /* u322 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		/* reset-gpios = <&PL_GPIO SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		sfpdd1_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* J350 sfp-dd at 0x50 */
+		};
+		sfpdd2_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* J352 sfp-dd at 0x50 */
+		};
+		sfpdd3_i2c: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* J385 sfp-dd at 0x50 */
+		};
+		sfpdd4_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* J387 sfp-dd at 0x50 */
+		};
+		rc21008a_gtclk1_i2c: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* u298 - rc21008a at 0x9 */
+			/* connector J370 */
+		};
+		rc21008a_gtclk2_i2c: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* u299 - rc21008a at 0x9 */
+			/* connector J371 */
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sck-kd-g-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sck-kd-g-revA.dts
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KD240 revA Carrier Card
+ *
+ * Copyright (C) 2021 - 2022, Xilinx, Inc.
+ * Copyright (C) 2022, Advanced Micro Devices, Inc.
+ *
+ * Michal Simek <michal.simek@amd.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "xlnx,zynqmp-sk-kd240-rev1",
+		     "xlnx,zynqmp-sk-kd240-revB",
+		     "xlnx,zynqmp-sk-kd240-revA",
+		     "xlnx,zynqmp-sk-kd240", "xlnx,zynqmp";
+	model = "ZynqMP KD240 revA/B/1";
+
+	ina260-u3 {
+		compatible = "iio-hwmon";
+		io-channels = <&u3 0>, <&u3 1>, <&u3 2>;
+	};
+
+	clk_26: clock2 { /* u17 - USB */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clk_25_0: clock4 { /* u92/u91 - GEM2 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clk_25_1: clock5 { /* u92/u91 - GEM3 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+};
+
+&can0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+};
+
+&i2c1 { /* I2C_SCK C26/C27 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	u3: ina260@40 { /* u3 */
+		compatible = "ti,ina260";
+		#io-channel-cells = <1>;
+		label = "ina260-u14";
+		reg = <0x40>;
+	};
+
+	slg7xl45106: gpio@11 { /* u13 - reset logic */
+		compatible = "dlg,slg7xl45106";
+		reg = <0x11>;
+		label = "resetchip";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "USB0_PHY_RESET_B", "",
+				  "SD_RESET_B", "USB0_HUB_RESET_B",
+				  "", "PS_GEM0_RESET_B",
+				  "", "";
+	};
+
+	/* usb5744@2d */
+};
+
+/* USB 3.0 */
+&psgtr {
+	status = "okay";
+	/* usb */
+	clocks = <&clk_26>;
+	clock-names = "ref2";
+};
+
+&usb0 { /* mio52 - mio63 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+	reset-gpios = <&slg7xl45106 0 GPIO_ACTIVE_LOW>;
+	assigned-clock-rates = <250000000>, <20000000>;
+
+	usbhub0: usb-hub { /* u36 */
+		i2c-bus = <&i2c1>;
+		compatible = "microchip,usb5744";
+		reset-gpios = <&slg7xl45106 3 GPIO_ACTIVE_LOW>;
+	};
+
+	usb2244: usb-sd { /* u41 */
+		compatible = "microchip,usb2244";
+		reset-gpios = <&slg7xl45106 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&gem1 { /* mdio mio50/51 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem1_default>;
+	assigned-clock-rates = <250000000>;
+
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@8 { /* Adin u31 */
+			reg = <8>;
+			adi,rx-internal-delay-ps = <2000>;
+			adi,tx-internal-delay-ps = <2000>;
+			adi,fifo-depth-bits = <8>;
+			reset-assert-us = <10>;
+			reset-deassert-us = <5000>;
+			reset-gpios = <&gpio 77 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* 2 more ethernet phys u32@2 and u34@3 */
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_can0_default: can0-default {
+		mux {
+			function = "can0";
+			groups = "can0_16_grp";
+		};
+
+		conf {
+			groups = "can0_16_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO66";
+			bias-pull-up;
+		};
+
+		conf-tx {
+			pins = "MIO67";
+			bias-pull-up;
+			drive-strength = <4>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		conf {
+			groups = "uart0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO70";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO71";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart0_17_grp";
+			function = "uart0";
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem1_default: gem1-default {
+		conf {
+			groups = "ethernet1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO45", "MIO46", "MIO47", "MIO48";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO44", "MIO49";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO38", "MIO39", "MIO40",
+				"MIO41", "MIO42", "MIO43";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio1";
+			groups = "mdio1_0_grp";
+		};
+
+		mux {
+			function = "ethernet1";
+			groups = "ethernet1_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		conf {
+			groups = "usb1_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			"MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+	rts-gpios = <&gpio 72 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-delay = <10 10>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
+	assigned-clock-rates = <100000000>;
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revA.dts
@@ -0,0 +1,397 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KR260 revA Carrier Card
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "xlnx,zynqmp-sk-kr260-revA",
+		     "xlnx,zynqmp-sk-kr260", "xlnx,zynqmp";
+	model = "ZynqMP KR260 revA";
+
+	ina260-u14 {
+		compatible = "iio-hwmon";
+		io-channels = <&u14 0>, <&u14 1>, <&u14 2>;
+	};
+
+	clk_27: clock0 { /* u86 - DP */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+
+	clk_125: si5332_0 { /* u17 - GEM0/1 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	clk_74: si5332_5 { /* u17 - SLVC-EC */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
+	};
+
+	clk_26: si5332_2 { /* u17 - USB */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clk_156: si5332_3 { /* u17 - SFP+ */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <156250000>;
+	};
+
+	clk_25_0: si5332_1 { /* u17 - GEM2 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clk_25_1: si5332_4 { /* u17 - GEM3 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+};
+
+&i2c1 { /* I2C_SCK C26/C27 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	u14: ina260@40 { /* u14 */
+		compatible = "ti,ina260";
+		#io-channel-cells = <1>;
+		label = "ina260-u14";
+		reg = <0x40>;
+	};
+
+	slg7xl45106: gpio@11 { /* u19 - reset logic */
+		compatible = "dlg,slg7xl45106";
+		reg = <0x11>;
+		label = "resetchip";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "USB0_PHY_RESET_B", "USB1_PHY_RESET_B",
+				  "SD_RESET_B", "USB0_HUB_RESET_B",
+				  "USB1_HUB_RESET_B", "PS_GEM0_RESET_B",
+				  "PS_GEM1_RESET_B", "";
+	};
+
+	i2c-mux@74 { /* u18 */
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		usbhub_i2c0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		usbhub_i2c1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		/* Bus 2/3 are not connected */
+	};
+
+	/* si5332@6a - u17 - clock-generator */
+};
+
+/* GEM SGMII/DP and USB 3.0 */
+&psgtr {
+	status = "okay";
+	/* gem0/1, dp, usb */
+	clocks = <&clk_125>, <&clk_27>, <&clk_26>;
+	clock-names = "ref0", "ref1", "ref2";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 1>;
+	assigned-clock-rates = <27000000>, <25000000>, <300000000>;
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+	assigned-clock-rates = <600000000>;
+};
+
+&usb0 { /* mio52 - mio63 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+	reset-gpios = <&slg7xl45106 0 GPIO_ACTIVE_LOW>;
+	assigned-clock-rates = <250000000>, <20000000>;
+
+	usbhub0: usb-hub { /* u43 */
+		i2c-bus = <&usbhub_i2c0>;
+		compatible = "microchip,usb5744";
+		reset-gpios = <&slg7xl45106 3 GPIO_ACTIVE_LOW>;
+	};
+
+	usb2244: usb-sd { /* u38 */
+		compatible = "microchip,usb2244";
+		reset-gpios = <&slg7xl45106 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&usb1 { /* mio64 - mio75 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
+	reset-gpios = <&slg7xl45106 1 GPIO_ACTIVE_LOW>;
+	assigned-clock-rates = <250000000>, <20000000>;
+
+	usbhub1: usb-hub { /* u84 */
+		i2c-bus = <&usbhub_i2c1>;
+		compatible = "microchip,usb5744";
+		reset-gpios = <&slg7xl45106 4 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&gem0 { /* mdio mio50/51 */
+	status = "okay";
+	phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>;
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	is-internal-pcspma;
+	assigned-clock-rates = <250000000>;
+};
+
+&gem1 { /* mdio mio50/51, gem mio38 - mio49 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem1_default>;
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	assigned-clock-rates = <250000000>;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@4 { /* u81 */
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <4>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-assert-us = <300>;
+			reset-deassert-us = <280>;
+			reset-gpios = <&slg7xl45106 5 GPIO_ACTIVE_LOW>;
+		};
+		phy1: ethernet-phy@8 { /* u36 */
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <8>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-assert-us = <100>;
+			reset-deassert-us = <280>;
+			reset-gpios = <&slg7xl45106 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* gem2/gem3 via PL with phys u79@2 and u80@3 */
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem1_default: gem1-default {
+		conf {
+			groups = "ethernet1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO44", "MIO46", "MIO48";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO45", "MIO47", "MIO49";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO38", "MIO39", "MIO40",
+				"MIO41", "MIO42", "MIO43";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio1";
+			groups = "mdio1_0_grp";
+		};
+
+		mux {
+			function = "ethernet1";
+			groups = "ethernet1_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		conf {
+			groups = "usb1_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			"MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revB.dts
@@ -0,0 +1,397 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KR260 revB Carrier Card (A03 revision)
+ *
+ * (C) Copyright 2021 - 2022, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "xlnx,zynqmp-sk-kr260-revB",
+		     "xlnx,zynqmp-sk-kr260", "xlnx,zynqmp";
+	model = "ZynqMP KR260 revB";
+
+	ina260-u14 {
+		compatible = "iio-hwmon";
+		io-channels = <&u14 0>, <&u14 1>, <&u14 2>;
+	};
+
+	clk_125: clock0 { /* u87 - GEM0/1 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	clk_27: clock1 { /* u86 - DP */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+
+	clk_26: clock2 { /* u89 - USB */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clk_156: clock3 { /* u90 - SFP+ */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <156250000>;
+	};
+
+	clk_25_0: clock4 { /* u92/u91 - GEM2 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clk_25_1: clock5 { /* u92/u91 - GEM3 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clk_74: clock6 { /* u88 - SLVC-EC */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
+	};
+};
+
+&i2c1 { /* I2C_SCK C26/C27 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	u14: ina260@40 { /* u14 */
+		compatible = "ti,ina260";
+		#io-channel-cells = <1>;
+		label = "ina260-u14";
+		reg = <0x40>;
+	};
+
+	slg7xl45106: gpio@11 { /* u19 - reset logic */
+		compatible = "dlg,slg7xl45106";
+		reg = <0x11>;
+		label = "resetchip";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "USB0_PHY_RESET_B", "USB1_PHY_RESET_B",
+				  "SD_RESET_B", "USB0_HUB_RESET_B",
+				  "USB1_HUB_RESET_B", "PS_GEM0_RESET_B",
+				  "PS_GEM1_RESET_B", "";
+	};
+
+	i2c-mux@74 { /* u18 */
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		usbhub_i2c0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		usbhub_i2c1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		/* Bus 2/3 are not connected */
+	};
+
+	/* si5332@6a - u17 - clock-generator */
+};
+
+/* GEM SGMII/DP and USB 3.0 */
+&psgtr {
+	status = "okay";
+	/* gem0/1, dp, usb */
+	clocks = <&clk_125>, <&clk_27>, <&clk_26>;
+	clock-names = "ref0", "ref1", "ref2";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 1>;
+	assigned-clock-rates = <27000000>, <25000000>, <300000000>;
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+	assigned-clock-rates = <600000000>;
+};
+
+&usb0 { /* mio52 - mio63 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+	reset-gpios = <&slg7xl45106 0 GPIO_ACTIVE_LOW>;
+	assigned-clock-rates = <250000000>, <20000000>;
+
+	usbhub0: usb-hub { /* u43 */
+		i2c-bus = <&usbhub_i2c0>;
+		compatible = "microchip,usb5744";
+		reset-gpios = <&slg7xl45106 3 GPIO_ACTIVE_LOW>;
+	};
+
+	usb2244: usb-sd { /* u38 */
+		compatible = "microchip,usb2244";
+		reset-gpios = <&slg7xl45106 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&usb1 { /* mio64 - mio75 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
+	reset-gpios = <&slg7xl45106 1 GPIO_ACTIVE_LOW>;
+	assigned-clock-rates = <250000000>, <20000000>;
+
+	usbhub1: usb-hub { /* u84 */
+		i2c-bus = <&usbhub_i2c1>;
+		compatible = "microchip,usb5744";
+		reset-gpios = <&slg7xl45106 4 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&gem0 { /* mdio mio50/51 */
+	status = "okay";
+	phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>;
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	is-internal-pcspma;
+	assigned-clock-rates = <250000000>;
+};
+
+&gem1 { /* mdio mio50/51, gem mio38 - mio49 */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem1_default>;
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	assigned-clock-rates = <250000000>;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@4 { /* u81 */
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <4>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-assert-us = <300>;
+			reset-deassert-us = <280>;
+			reset-gpios = <&slg7xl45106 5 GPIO_ACTIVE_LOW>;
+		};
+		phy1: ethernet-phy@8 { /* u36 */
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <8>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-assert-us = <100>;
+			reset-deassert-us = <280>;
+			reset-gpios = <&slg7xl45106 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* gem2/gem3 via PL with phys u79@2 and u80@3 */
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem1_default: gem1-default {
+		conf {
+			groups = "ethernet1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO44", "MIO46", "MIO48";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO45", "MIO47", "MIO49";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO38", "MIO39", "MIO40",
+				"MIO41", "MIO42", "MIO43";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio1";
+			groups = "mdio1_0_grp";
+		};
+
+		mux {
+			function = "ethernet1";
+			groups = "ethernet1_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		conf {
+			groups = "usb1_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			"MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KV260 revA Carrier Card
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * SD level shifter:
+ * "A" – A01 board un-modified (NXP)
+ * "Y" – A01 board modified with legacy interposer (Nexperia)
+ * "Z" – A01 board modified with Diode interposer
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "xlnx,zynqmp-sk-kv260-revA",
+		     "xlnx,zynqmp-sk-kv260-revY",
+		     "xlnx,zynqmp-sk-kv260-revZ",
+		     "xlnx,zynqmp-sk-kv260", "xlnx,zynqmp";
+	model = "ZynqMP KV260 revA";
+};
+
+&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	u14: ina260@40 { /* u14 */
+		compatible = "ti,ina260";
+		#io-channel-cells = <1>;
+		label = "ina260-u14";
+		reg = <0x40>;
+	};
+	/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
+};
+
+&amba {
+	ina260-u14 {
+		compatible = "iio-hwmon";
+		io-channels = <&u14 0>, <&u14 1>, <&u14 2>;
+	};
+
+	si5332_0: si5332_0 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	si5332_1: si5332_1 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	si5332_2: si5332_2 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+
+	si5332_3: si5332_3 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	si5332_4: si5332_4 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	si5332_5: si5332_5 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+/* DP/USB 3.0 and SATA */
+&psgtr {
+	status = "okay";
+	/* pcie, usb3, sata */
+	clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
+	clock-names = "ref0", "ref1", "ref2";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 2>;
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
+	assigned-clock-rates = <27000000>, <25000000>, <300000000>;
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+	assigned-clock-rates = <600000000>;
+};
+
+&usb0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+	usbhub: usb5744 { /* u43 */
+		compatible = "microchip,usb5744";
+		reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&sdhci1 { /* on CC with tuned parameters */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	/*
+	 * SD 3.0 requires level shifter and this property
+	 * should be removed if the board has level shifter and
+	 * need to work in UHS mode
+	 */
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+	assigned-clock-rates = <187498123>;
+	bus-width = <8>;
+};
+
+&gem3 { /* required by spec */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	assigned-clock-rates = <250000000>;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@1 {
+			#phy-cells = <1>;
+			reg = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-assert-us = <100>;
+			reset-deassert-us = <280>;
+			reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO72", "MIO74";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO71", "MIO73", "MIO75";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66",
+				"MIO67", "MIO68", "MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts
@@ -0,0 +1,334 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KV260 revA Carrier Card
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "xlnx,zynqmp-sk-kv260-rev2",
+		     "xlnx,zynqmp-sk-kv260-rev1",
+		     "xlnx,zynqmp-sk-kv260-revB",
+		     "xlnx,zynqmp-sk-kv260", "xlnx,zynqmp";
+	model = "ZynqMP KV260 revB";
+};
+
+&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	u14: ina260@40 { /* u14 */
+		compatible = "ti,ina260";
+		#io-channel-cells = <1>;
+		label = "ina260-u14";
+		reg = <0x40>;
+	};
+	/* u43 - 0x2d - USB hub */
+	/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
+};
+
+&amba {
+	ina260-u14 {
+		compatible = "iio-hwmon";
+		io-channels = <&u14 0>, <&u14 1>, <&u14 2>;
+	};
+
+	si5332_0: si5332_0 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	si5332_1: si5332_1 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	si5332_2: si5332_2 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+
+	si5332_3: si5332_3 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	si5332_4: si5332_4 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	si5332_5: si5332_5 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+/* DP/USB 3.0 */
+&psgtr {
+	status = "okay";
+	/* pcie, usb3, sata */
+	clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
+	clock-names = "ref0", "ref1", "ref2";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
+	assigned-clock-rates = <27000000>, <25000000>, <300000000>;
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+	assigned-clock-rates = <600000000>;
+};
+
+&usb0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+	assigned-clock-rates = <250000000>, <20000000>;
+
+	usb5744: usb-hub { /* u43 */
+		status = "okay";
+		compatible = "microchip,usb5744";
+		i2c-bus = <&i2c1>;
+		reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&sdhci1 { /* on CC with tuned parameters */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	/*
+	 * SD 3.0 requires level shifter and this property
+	 * should be removed if the board has level shifter and
+	 * need to work in UHS mode
+	 */
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+	clk-phase-sd-hs = <126>, <60>;
+	clk-phase-uhs-sdr25 = <120>, <60>;
+	clk-phase-uhs-ddr50 = <126>, <48>;
+	assigned-clock-rates = <187498123>;
+	bus-width = <8>;
+};
+
+&gem3 { /* required by spec */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	assigned-clock-rates = <250000000>;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@1 {
+			#phy-cells = <1>;
+			reg = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-assert-us = <100>;
+			reset-deassert-us = <280>;
+			reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO72", "MIO74";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO71", "MIO73", "MIO75";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66",
+				"MIO67", "MIO68", "MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sm-k24-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sm-k24-revA.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SM-K24 RevA
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ * (C) Copyright 2022, Advanced Micro Devices, Inc.
+ *
+ * Michal Simek <michal.simek@amd.com>
+ */
+
+#include "zynqmp-sm-k26-revA.dts"
+
+/ {
+	model = "ZynqMP SM-K24 RevA/B/1";
+	compatible = "xlnx,zynqmp-sm-k24-rev1", "xlnx,zynqmp-sm-k24-revB",
+		     "xlnx,zynqmp-sm-k24-revA", "xlnx,zynqmp-sm-k24",
+		     "xlnx,zynqmp";
+
+	memory@0 {
+		device_type = "memory"; /* 2GB */
+		reg = <0 0 0 0x80000000>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
@@ -0,0 +1,479 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SM-K26 rev1/B/A
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/ {
+	model = "ZynqMP SM-K26 Rev1/B/A";
+	compatible = "xlnx,zynqmp-sm-k26-rev1", "xlnx,zynqmp-sm-k26-revB",
+		     "xlnx,zynqmp-sm-k26-revA", "xlnx,zynqmp-sm-k26",
+		     "xlnx,zynqmp";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		nvmem1 = &eeprom_cc;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		spi0 = &qspi;
+		spi1 = &spi0;
+		spi2 = &spi1;
+		usb0 = &usb0;
+		usb1 = &usb1;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory"; /* 4GB */
+		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		pmu_region: pmu@7ff00000 {
+			reg = <0x0 0x7ff00000 0x0 0x100000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		fwuen {
+			label = "fwuen";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_MISC>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ds35-led {
+			label = "heartbeat";
+			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		ds36-led {
+			label = "vbus_det";
+			gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	ams {
+		compatible = "iio-hwmon";
+		io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
+			<&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>,
+			<&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>,
+			<&xilinx_ams 9>, <&xilinx_ams 10>, <&xilinx_ams 11>,
+			<&xilinx_ams 12>, <&xilinx_ams 13>, <&xilinx_ams 14>,
+			<&xilinx_ams 15>, <&xilinx_ams 16>, <&xilinx_ams 17>,
+			<&xilinx_ams 18>, <&xilinx_ams 19>, <&xilinx_ams 20>,
+			<&xilinx_ams 21>, <&xilinx_ams 22>, <&xilinx_ams 23>,
+			<&xilinx_ams 24>, <&xilinx_ams 25>, <&xilinx_ams 26>,
+			<&xilinx_ams 27>, <&xilinx_ams 28>, <&xilinx_ams 29>;
+	};
+
+	pwm-fan {
+		compatible = "pwm-fan";
+		status = "okay";
+		pwms = <&ttc0 2 40000 0>;
+	};
+};
+
+&modepin_gpio {
+	label = "modepin";
+};
+
+&ttc0 {
+	status = "okay";
+	#pwm-cells = <3>;
+};
+
+&uart1 { /* MIO36/MIO37 */
+	status = "okay";
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_sdhci0_default: sdhci0-default {
+		conf {
+			groups = "sdio0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux {
+			groups = "sdio0_0_grp";
+			function = "sdio0";
+		};
+	};
+};
+
+&qspi { /* MIO 0-5 - U143 */
+	status = "okay";
+	is-dual = <0>;
+	flash@0 { /* MT25QU512A */
+		compatible = "mt25qu512a", "jedec,spi-nor"; /* 64MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>; /* 40MHz */
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Image Selector";
+				reg = <0x0 0x80000>; /* 512KB */
+				read-only;
+				lock;
+			};
+			partition@80000 {
+				label = "Image Selector Golden";
+				reg = <0x80000 0x80000>; /* 512KB */
+				read-only;
+				lock;
+			};
+			partition@100000 {
+				label = "Persistent Register";
+				reg = <0x100000 0x20000>; /* 128KB */
+			};
+			partition@120000 {
+				label = "Persistent Register Backup";
+				reg = <0x120000 0x20000>; /* 128KB */
+			};
+			partition@140000 {
+				label = "Open_1";
+				reg = <0x140000 0xC0000>; /* 768KB */
+			};
+			partition@200000 {
+				label = "Image A (FSBL, PMU, ATF, U-Boot)";
+				reg = <0x200000 0xD00000>; /* 13MB */
+			};
+			partition@f00000 {
+				label = "ImgSel Image A Catch";
+				reg = <0xF00000 0x80000>; /* 512KB */
+				read-only;
+				lock;
+			};
+			partition@f80000 {
+				label = "Image B (FSBL, PMU, ATF, U-Boot)";
+				reg = <0xF80000 0xD00000>; /* 13MB */
+			};
+			partition@1c80000 {
+				label = "ImgSel Image B Catch";
+				reg = <0x1C80000 0x80000>; /* 512KB */
+				read-only;
+				lock;
+			};
+			partition@1d00000 {
+				label = "Open_2";
+				reg = <0x1D00000 0x100000>; /* 1MB */
+			};
+			partition@1e00000 {
+				label = "Recovery Image";
+				reg = <0x1E00000 0x200000>; /* 2MB */
+				read-only;
+				lock;
+			};
+			partition@2000000 {
+				label = "Recovery Image Backup";
+				reg = <0x2000000 0x200000>; /* 2MB */
+				read-only;
+				lock;
+			};
+			partition@2200000 {
+				label = "U-Boot storage variables";
+				reg = <0x2200000 0x20000>; /* 128KB */
+			};
+			partition@2220000 {
+				label = "U-Boot storage variables backup";
+				reg = <0x2220000 0x20000>; /* 128KB */
+			};
+			partition@2240000 {
+				label = "SHA256";
+				reg = <0x2240000 0x40000>; /* 256B but 256KB sector */
+				read-only;
+				lock;
+			};
+			partition@2280000 {
+				label = "Secure OS Storage";
+				reg = <0x2280000 0x20000>; /* 128KB */
+			};
+			partition@22A0000 {
+				label = "User";
+				reg = <0x22A0000 0x1d60000>; /* 29.375 MB */
+			};
+		};
+	};
+};
+
+&sdhci0 { /* MIO13-23 - 16GB emmc MTFC16GAPALBH-IT - U133A */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+	assigned-clock-rates = <187498123>;
+};
+
+&spi1 { /* MIO6, 9-11 */
+	status = "okay";
+	label = "TPM";
+	num-cs = <1>;
+	tpm@0 { /* slm9670 - U144 */
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+		reg = <0>;
+		spi-max-frequency = <18500000>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	u-boot,dm-pre-reloc;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	eeprom: eeprom@50 { /* u46 - also at address 0x58 */
+		u-boot,dm-pre-reloc;
+		compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
+		reg = <0x50>;
+		/* WP pin EE_WP_EN connected to slg7x644092@68 */
+	};
+
+	eeprom_cc: eeprom@51 { /* required by spec - also at address 0x59 */
+		u-boot,dm-pre-reloc;
+		compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
+		reg = <0x51>;
+	};
+
+	/* da9062@30 - u170 - also at address 0x31 */
+	/* da9131@33 - u167 */
+	da9131: pmic@33 {
+		compatible = "dlg,da9131";
+		reg = <0x33>;
+		regulators {
+			da9131_buck1: buck1 {
+				regulator-name = "da9131_buck1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			da9131_buck2: buck2 {
+				regulator-name = "da9131_buck2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	/* da9130@32 - u166 */
+	da9130: pmic@32 {
+		compatible = "dlg,da9130";
+		reg = <0x32>;
+		regulators {
+			da9130_buck1: buck1 {
+				regulator-name = "da9130_buck1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	/* slg7x644091@70 - u168 NOT accessible due to address conflict with stdp4320 */
+	/*
+	 * stdp4320 - u27 FW has below two issues to be fixed in next board revision.
+	 * Device acknowledging to addresses 0x5C, 0x5D, 0x70, 0x72, 0x76.
+	 * Address conflict with slg7x644091@70 making both the devices NOT accessible.
+	 * With the FW fix, stdp4320 should respond to address 0x73 only.
+	 */
+	/* slg7x644092@68 - u169 */
+	/* Also connected via JA1C as C23/C24 */
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
+			  "QSPI_CS_B", "SPI_CLK", "LED1", "LED2", "SPI_CS_B", /* 5 - 9 */
+			  "SPI_MISO", "SPI_MOSI", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+			  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+			  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST", "I2C1_SCL", /* 20 - 24 */
+			  "I2C1_SDA", "", "", "", "", /* 25 - 29 */
+			  "", "", "", "", "", /* 30 - 34 */
+			  "", "", "", "", "", /* 35 - 39 */
+			  "", "", "", "", "", /* 40 - 44 */
+			  "", "", "", "", "", /* 45 - 49 */
+			  "", "", "", "", "", /* 50 - 54 */
+			  "", "", "", "", "", /* 55 - 59 */
+			  "", "", "", "", "", /* 60 - 64 */
+			  "", "", "", "", "", /* 65 - 69 */
+			  "", "", "", "", "", /* 70 - 74 */
+			  "", "", "", /* 75 - 77, MIO end and EMIO start */
+			  "", "", /* 78 - 79 */
+			  "", "", "", "", "", /* 80 - 84 */
+			  "", "", "", "", "", /* 85 - 89 */
+			  "", "", "", "", "", /* 90 - 94 */
+			  "", "", "", "", "", /* 95 - 99 */
+			  "", "", "", "", "", /* 100 - 104 */
+			  "", "", "", "", "", /* 105 - 109 */
+			  "", "", "", "", "", /* 110 - 114 */
+			  "", "", "", "", "", /* 115 - 119 */
+			  "", "", "", "", "", /* 120 - 124 */
+			  "", "", "", "", "", /* 125 - 129 */
+			  "", "", "", "", "", /* 130 - 134 */
+			  "", "", "", "", "", /* 135 - 139 */
+			  "", "", "", "", "", /* 140 - 144 */
+			  "", "", "", "", "", /* 145 - 149 */
+			  "", "", "", "", "", /* 150 - 154 */
+			  "", "", "", "", "", /* 155 - 159 */
+			  "", "", "", "", "", /* 160 - 164 */
+			  "", "", "", "", "", /* 165 - 169 */
+			  "", "", "", ""; /* 170 - 173 */
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&lpd_dma_chan1 {
+	status = "okay";
+};
+
+&lpd_dma_chan2 {
+	status = "okay";
+};
+
+&lpd_dma_chan3 {
+	status = "okay";
+};
+
+&lpd_dma_chan4 {
+	status = "okay";
+};
+
+&lpd_dma_chan5 {
+	status = "okay";
+};
+
+&lpd_dma_chan6 {
+	status = "okay";
+};
+
+&lpd_dma_chan7 {
+	status = "okay";
+};
+
+&lpd_dma_chan8 {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&lpd_watchdog {
+	status = "okay";
+};
+
+&watchdog0 {
+	status = "okay";
+};
+
+&cpu_opp_table {
+	opp00 {
+		opp-hz = /bits/ 64 <1333333333>;
+	};
+	opp01 {
+		opp-hz = /bits/ 64 <666666666>;
+	};
+	opp02 {
+		opp-hz = /bits/ 64 <444444444>;
+	};
+	opp03 {
+		opp-hz = /bits/ 64 <333333333>;
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-smk-k24-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-smk-k24-revA.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SMK-K24 RevA
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ * (C) Copyright 2022, Advanced Micro Devices, Inc.
+ *
+ * Michal Simek <michal.simek@amd.com>
+ */
+
+#include "zynqmp-sm-k24-revA.dts"
+
+/ {
+	model = "ZynqMP SMK-K24 RevA";
+	compatible = "xlnx,zynqmp-smk-k24-revA", "xlnx,zynqmp-smk-k24",
+		     "xlnx,zynqmp";
+};
+
+&sdhci0 {
+	status = "disabled";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SMK-K26 rev1/B/A
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-sm-k26-revA.dts"
+
+/ {
+	model = "ZynqMP SMK-K26 Rev1/B/A";
+	compatible = "xlnx,zynqmp-smk-k26-rev1", "xlnx,zynqmp-smk-k26-revB",
+		     "xlnx,zynqmp-smk-k26-revA", "xlnx,zynqmp-smk-k26",
+		     "xlnx,zynqmp";
+};
+
+&sdhci0 {
+	status = "disabled";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-vp-x-a2785-00-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-vp-x-a2785-00-revA.dts
@@ -0,0 +1,437 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP vp-x-a2785-00 RevA System Controller
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP System Controller on vp-x-a2785-00 board RevA";
+	compatible = "xlnx,zynqmp-vp-x-a2785-00-revA",
+		     "xlnx,zynqmp-vp-x-a2785-00", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		nvmem0 = &eeprom;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		j383 {
+			label = "j383";
+			gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat-led { /* ds52 */
+			label = "heartbeat";
+			gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	si5332_0: si5332_0 { /* ps_ref_clk - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33333333>;
+	};
+
+	si5332_1: si5332_1 { /* clk0_sgmii - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33333333>; /* FIXME */
+	};
+
+	si5332_2: si5332_2 { /* clk1_usb - u142 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+&qspi { /* MIO 0-5 */
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* u285 - mt25qu512abb8e12 512Mib */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>; /* maybe 4 here */
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		partition@0 { /* for testing purpose */
+			label = "qspi";
+			reg = <0 0x4000000>;
+		};
+	};
+};
+
+&sdhci1 { /* sd MIO 45-51 */
+	status = "okay";
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+	u-boot,dm-pre-reloc;
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii"; /* DTG generates this properly 1512 */
+	is-internal-pcspma;
+	/* phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>; */
+	/* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
+	phy0: ethernet-phy@0 { /* u131 - M88e1512 */
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
+		  "QSPI_CS_B", "", "", "SYSCTLR_GPIO", "SYSCTLR_LED", /* 5 - 9 */
+		  "SYSCTLR_PB", "PMC_ZU4_TRIGGER", "", "", "", /* 10 - 14 */
+		  "", "", "", "", "", /* 15 - 19 */
+		  "", "", "", "", "", /* 20 - 24 */
+		  "", "", "", "", "", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "", "", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "SD1_CD", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */
+		  "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */
+		  "", "", "", "", "", /* 65 - 69 */
+		  "", "", "", "", "", /* 70 - 74 */
+		  "", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 - 89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 34 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+
+	tca6416_u233: gpio@20 { /* u233 */ /* FIXME - address maybe wrong */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "", "", /* 0 - 3 */
+				  "", "", "", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "", "", "", "VCCINT_FAULT_B", /* 10 - 13 */
+				  "VCCINT_VRHOT_B", "", "PMBUS_ALERT", "PMBUS1_INA226_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@74 { /* u33 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		pmbus_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* On connector J325 */
+			reg_vccint: tps53681@c0 { /* u266 */
+				compatible = "ti,tps53681", "ti,tps53679";
+				reg = <0xc0>;
+			};
+			reg_vcc1v1_lp4: tps544@d { /* u85 */
+				compatible = "ti,tps544b25";
+				reg = <0xd>;
+			};
+			reg_mgtyavcc: tps544@10 { /* u274 */
+				compatible = "ti,tps544b25";
+				reg = <0x10>;
+			};
+			reg_mgtyavtt: tps544@11 { /* u275 */
+				compatible = "ti,tps544b25";
+				reg = <0x11>;
+			};
+			reg_vccaux: tps544@12 { /* u276 */
+				compatible = "ti,tps544b25";
+				reg = <0x12>;
+			};
+			reg_vcc_cpm: tps544@14 { /* u272 */
+				compatible = "ti,tps544b25";
+				reg = <0x14>;
+			};
+			reg_util_3v3: tps544@1d { /* u278 */
+				compatible = "ti,tps544b25";
+				reg = <0x1d>;
+			};
+		};
+		pmbus1_ina226_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME check alerts coming to SC */
+			vcc_cpm: ina226@44 { /* u273 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+		};
+		i2c@2 { /* NC */ /* FIXME maybe remove */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		pcie_smbus: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+		pcie2_smbus: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+		i2c@5 { /* NC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+		user_si570: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+		/* 7 unused */
+	};
+};
+
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
+
+	i2c-mux@74 { /* u35 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		dc_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u34 - m24128 16kB */
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x54>; /* & 0x5c */
+			};
+			si570_ref_clk: clock-generator@5d { /* u32 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "ref_clk";
+				silabs,skip-recall;
+			};
+		};
+		i2c@1 { /* NC - FIXME */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c@2 { /* NC - FIXME */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c@3 { /* NC - FIXME */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+		lpddr4_si570_clk2_i2c: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			lpddr4_clk2: clock-generator@60 { /* u3 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk2";
+			};
+		};
+		lpddr4_si570_clk1_i2c: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			lpddr4_clk1: clock-generator@60 { /* u248 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk1";
+			};
+		};
+		/* 6-7 unused */
+	};
+};
+
+&usb0 { /* MIO52 - MIO63 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
+};
+
+&psgtr {
+	status = "okay";
+	/* sgmii, usb3 */
+	clocks = <&si5332_1>, <&si5332_2>;
+	clock-names = "ref0", "ref1";
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	maximum-speed = "super-speed";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_8_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_8_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_34_grp", "gpio0_35_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_34_grp", "gpio0_35_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_9_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_9_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-vpk120-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-vpk120-revA.dts
@@ -0,0 +1,603 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP VPK120 RevA System Controller
+ *
+ * (C) Copyright 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP System Controller on VPK120 board RevA";
+	compatible = "xlnx,zynqmp-vpk120-revA",
+		     "xlnx,zynqmp-vpk120", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		nvmem0 = &eeprom;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	si570_user1_fmc_clk: si570_user1_fmc_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&user_si570_1>;
+	};
+
+	si570_ref_clk: si570_ref_clk {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&ref_clk>;
+	};
+
+	si570_lpddr4_clk3: si570_lpddr4_clk3 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk3>;
+	};
+
+	si570_lpddr4_clk2: si570_lpddr4_clk2 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk2>;
+	};
+
+	si570_lpddr4_clk1: si570_lpddr4_clk1 {
+		status = "okay";
+		compatible = "xlnx,fclk";
+		clocks = <&lpddr4_clk1>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		sw16 {
+			label = "sw16";
+			gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat-led { /* ds40 */
+			label = "heartbeat";
+			gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	si5332_0: si5332_0 { /* ps_ref_clk */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33333333>;
+	};
+
+	si5332_1: si5332_1 { /* clk0_sgmii */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33333333>; /* FIXME */
+	};
+
+	si5332_2: si5332_2 { /* clk1_usb */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+&qspi { /* MIO 0-5 */
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* mt25qu512abb8e12 512Mib */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		partition@0 { /* for testing purpose */
+			label = "qspi";
+			reg = <0 0x4000000>;
+		};
+	};
+};
+
+&sdhci0 { /* emmc MIO 13-23 - with some settings MTFC16GAPALBH 16GB */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+};
+
+&uart0 { /* uart0 MIO38-39 */
+	status = "okay";
+	u-boot,dm-pre-reloc;
+};
+
+&gem0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii"; /* DTG generates this properly 1512 */
+	is-internal-pcspma;
+	/* phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>; */
+	/* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
+		  "QSPI_CS_B", "", "", "SYSCTLR_GPIO", "SYSCTLR_LED", /* 5 - 9 */
+		  "SYSCTLR_PB", "PMC_ZU4_TRIGGER", "", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+		  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+		  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */
+		  "", "", "", "", "", /* 25 - 29 */
+		  "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */
+		  "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */
+		  "", "", "ETH_RESET_B", "", "", /* 40 - 44 */
+		  "", "", "", "", "", /* 45 - 49 */
+		  "", "", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
+		  "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
+		  "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */
+		  "", "", "", "", "", /* 65 - 69 */
+		  "", "", "", "", "", /* 70 - 74 */
+		  "", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "SYSCTLR_VERSAL_MODE0", "SYSCTLR_VERSAL_MODE1", /* 78 - 79 */
+		  "SYSCTLR_VERSAL_MODE2", "SYSCTLR_VERSAL_MODE3", "SYSCTLR_POR_B_LS", "", "", /* 80 - 84 */
+		  "SYSCTLR_JTAG_S0", "SYSCTLR_JTAG_S1", "SYSCTLR_IIC_MUX0_RESET_B", "SYSCTLR_IIC_MUX1_RESET_B", "", /* 85 - 89 */
+		  "SYSCTLR_GPIO0", "SYSCTLR_GPIO1", "SYSCTLR_GPIO2", "SYSCTLR_GPIO3", "SYSCTLR_GPIO4", /* 90 - 94 */
+		  "SYSCTLR_GPIO5", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 { /* MIO 34-35 - can't stay here */
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 34 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+
+	tca6416_u233: gpio@20 { /* u233 */ /* FIXME - address maybe wrong */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "QSFPDD1_MODSELL", "QSFPDD1_MODSELL", /* 0 - 3 */
+				  "PMBUS2_INA226_ALERT", "", "", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "FMCP1_FMC_PRSNT_M2C_B", "", "FMCP1_FMCP_PRSNT_M2C_B", "", /* 10 - 13 */
+				  "VCCINT_VRHOT_B", "8A34001_EXP_RST_B", "PMBUS_ALERT", "PMBUS1_INA226_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@74 { /* u33 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		pmbus_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* On connector J325 */
+			ir38060_41: regulator@41 { /* IR38060 - u259 */
+				compatible = "infineon,ir38060", "infineon,ir38064";
+				reg = <0x41>; /* i2c addr 0x11 */
+			};
+			ir38164_43: regulator@43 { /* IR38164 - u13 */
+				compatible = "infineon,ir38164";
+				reg = <0x43>; /* i2c addr 0x13 */
+			};
+			ir35221_45: pmic@46 { /* IR35221 - u152 */
+				compatible = "infineon,ir35221";
+				reg = <0x46>; /* PMBUS - 0x16 */
+			};
+			irps5401_47: pmic5401@47 { /* IRPS5401 - u160 */
+				compatible = "infineon,irps5401";
+				reg = <0x47>; /* i2c addr 0x17 */
+			};
+			ir38164_49: regulator@49 { /* IR38164 - u189 */
+				compatible = "infineon,ir38164";
+				reg = <0x49>; /* i2c addr 0x19 */
+			};
+			irps5401_4c: pmic@4c { /* IRPS5401 - u167 */
+				compatible = "infineon,irps5401";
+				reg = <0x4c>; /* i2c addr 0x1c */
+			};
+			irps5401_4d: pmic@4d { /* IRPS5401 - u175 */
+				compatible = "infineon,irps5401";
+				reg = <0x4d>; /* i2c addr 0x1c */
+			};
+			ir38164_4e: regulator@4e { /* IR38164 - u184 */
+				compatible = "infineon,ir38164";
+				reg = <0x4e>; /* i2c addr 0x1e */
+			};
+			ir38164_4f: regulator@4f { /* IR38164 - u187 */
+				compatible = "infineon,ir38164";
+				reg = <0x4f>; /* i2c addr 0x1f */
+			};
+		};
+		pmbus1_ina226_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME check alerts coming to SC */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vcc_soc: ina226@41 { /* u161 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc_pmc: ina226@42 { /* u163 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc_ram: ina226@43 { /* u5 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcc_pslp: ina226@44 { /* u165 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>;
+			};
+			vcc_psfp: ina226@45 { /* u164 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 { /* NC */ /* FIXME maybe remove */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		pmbus2_ina226_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FIXME check alerts coming to SC */
+			vccaux: ina226@40 { /* u166 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccaux_pmc: ina226@41 { /* u168 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@42 { /* u265 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v5: ina226@43 { /* u264 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vcco_mio: ina226@45 { /* u172 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavtt: ina226@46 { /* u188 */
+				compatible = "ti,ina226";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			vcco_502: ina226@47 { /* u174 */
+				compatible = "ti,ina226";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			mgtvccaux: ina226@48 { /* u176 */
+				compatible = "ti,ina226";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v1_lp4: ina226@49 { /* u186 */
+				compatible = "ti,ina226";
+				reg = <0x49>;
+				shunt-resistor = <2000>;
+			};
+			vadj_fmc: ina226@4a { /* u184 */
+				compatible = "ti,ina226";
+				reg = <0x4a>;
+				shunt-resistor = <2000>;
+			};
+			lpdmgtyavcc: ina226@4b { /* u177 */
+				compatible = "ti,ina226";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			lpdmgtyavtt: ina226@4c { /* u260 */
+				compatible = "ti,ina226";
+				reg = <0x4c>;
+				shunt-resistor = <2000>;
+			};
+			lpdmgtyvccaux: ina226@4d { /* u234 */
+				compatible = "ti,ina226";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@4 { /* NC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+		i2c@5 { /* NC */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+		user_si570: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			user_si570_1: clock-generator@5f { /* USER C0 SI570 - u205 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5f>;
+				temperature-stability = <50>;
+				factory-fout = <100000000>;
+				clock-frequency = <100000000>;
+				clock-output-names = "fmc_si570";
+			};
+
+		};
+		/* 7 unused */
+	};
+};
+
+&i2c1 { /* i2c1 MIO 36-37 */
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
+
+	i2c-mux@74 { /* u35 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */
+		ref_clk_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* Use for storing information about SC board */
+			eeprom: eeprom@54 { /* u34 - m24128 16kB */
+				compatible = "st,24c128", "atmel,24c128";
+				reg = <0x54>; /* & 0x5c */
+			};
+			ref_clk: clock-generator@5d { /* u32 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "ref_clk";
+				silabs,skip-recall;
+			};
+		};
+		fmcp1_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* FIXME connection to Samtec J51C */
+			/* expected eeprom 0x50 SE cards */
+		};
+		i2c@2 { /* NC - FIXME */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		lpddr4_si570_clk3_i2c: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			lpddr4_clk3: clock-generator@60 { /* u4 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk3";
+			};
+		};
+		lpddr4_si570_clk2_i2c: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			lpddr4_clk2: clock-generator@60 { /* u3 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk2";
+			};
+		};
+		lpddr4_si570_clk1_i2c: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			lpddr4_clk1: clock-generator@60 { /* u248 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x60>;
+				temperature-stability = <50>;
+				factory-fout = <200000000>;
+				clock-frequency = <200000000>;
+				clock-output-names = "lpddr4_clk1";
+			};
+		};
+		qsfpdd_i2c: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* J1/J2 connectors */
+		};
+		idt8a34001_i2c: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* Via J310 connector */
+			idt_8a34001: phc@5b {
+				compatible = "idt,8a34001"; /* u219B */
+				reg = <0x5b>; /* FIXME not in schematics */
+			};
+		};
+	};
+};
+
+&usb0 { /* MIO52 - MIO63 */
+	status = "okay";
+	xlnx,usb-polarity = <0>;
+	xlnx,usb-reset-mode = <0>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
+};
+
+&psgtr {
+	status = "okay";
+	/* sgmii, usb3 */
+	clocks = <&si5332_1>, <&si5332_2>;
+	clock-names = "ref0", "ref1";
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	maximum-speed = "super-speed";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_8_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_8_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_34_grp", "gpio0_35_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_34_grp", "gpio0_35_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_9_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_9_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZC1232
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -19,6 +19,7 @@
 	aliases {
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -36,6 +37,35 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB FIXME */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZC1254
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2020, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
@@ -20,6 +20,7 @@
 	aliases {
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -37,6 +38,35 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &uart0 {
 	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm015-dc1
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -11,7 +11,9 @@
 
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 
 / {
 	model = "ZynqMP zc1751-xm015-dc1 RevA";
@@ -24,6 +26,8 @@
 		mmc1 = &sdhci1;
 		rtc0 = &rtc;
 		serial0 = &uart0;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -35,6 +39,24 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
 	};
+
+	clock_si5338_0: clk27 {	/* u55 SI5338-GM */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+
+	clock_si5338_2: clk26 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clock_si5338_3: clk150 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <150000000>;
+	};
 };
 
 &fpd_dma_chan1 {
@@ -73,6 +95,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
@@ -80,12 +104,22 @@
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
 };
 
+&gpu {
+	status = "okay";
+};
 
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
 
 	eeprom: eeprom@55 {
 		compatible = "atmel,24c64"; /* 24AA64 */
@@ -93,6 +127,255 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_9_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_9_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_8_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_8_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO34";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO35";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_0_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio0_cd_0_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "sdio0_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio0_wp_0_grp";
+			function = "sdio0_wp";
+		};
+
+		conf-wp {
+			groups = "sdio0_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio1_wp_0_grp";
+			function = "sdio1_wp";
+		};
+
+		conf-wp {
+			groups = "sdio1_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux {
+			function = "gpio0";
+			groups = "gpio0_38_grp";
+		};
+
+		conf {
+			groups = "gpio0_38_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* dp, usb3, sata */
+	clocks = <&clock_si5338_0>, <&clock_si5338_2>, <&clock_si5338_3>;
+	clock-names = "ref1", "ref2", "ref3";
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* Micron MT25QU512ABB8ESF */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -108,25 +391,76 @@
 	ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
 };
 
 /* eMMC */
 &sdhci0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
 	bus-width = <8>;
+	xlnx,mio-bank = <0>;
 };
 
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 0>,
+	       <&psgtr 0 PHY_TYPE_DP 1 1>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm016-dc2
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -12,14 +12,13 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 
 / {
 	model = "ZynqMP zc1751-xm016-dc2 RevA";
 	compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
 
 	aliases {
-		can0 = &can0;
-		can1 = &can1;
 		ethernet0 = &gem2;
 		i2c0 = &i2c0;
 		rtc0 = &rtc;
@@ -27,6 +26,7 @@
 		serial1 = &uart1;
 		spi0 = &spi0;
 		spi1 = &spi1;
+		usb0 = &usb1;
 	};
 
 	chosen {
@@ -42,10 +42,14 @@
 
 &can0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
 };
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &fpd_dma_chan1 {
@@ -84,6 +88,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem2_default>;
 	phy0: ethernet-phy@5 {
 		reg = <5>;
 		ti,rx-internal-delay = <0x8>;
@@ -100,6 +106,11 @@
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u26: gpio@20 {
 		compatible = "ti,tca6416";
@@ -115,6 +126,368 @@
 	};
 };
 
+&nand0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand0_default>;
+	arasan,has-mdma;
+
+	nand@0 {
+		reg = <0x0>;
+		#address-cells = <0x2>;
+		#size-cells = <0x1>;
+		nand-ecc-mode = "soft";
+		nand-ecc-algo = "bch";
+		nand-rb = <0>;
+		label = "main-storage-0";
+		nand-ecc-step-size = <1024>;
+		nand-ecc-strength = <24>;
+
+		partition@0 {	/* for testing purpose */
+			label = "nand-fsbl-uboot";
+			reg = <0x0 0x0 0x400000>;
+		};
+		partition@1 {	/* for testing purpose */
+			label = "nand-linux";
+			reg = <0x0 0x400000 0x1400000>;
+		};
+		partition@2 {	/* for testing purpose */
+			label = "nand-device-tree";
+			reg = <0x0 0x1800000 0x400000>;
+		};
+		partition@3 {	/* for testing purpose */
+			label = "nand-rootfs";
+			reg = <0x0 0x1c00000 0x1400000>;
+		};
+		partition@4 {	/* for testing purpose */
+			label = "nand-bitstream";
+			reg = <0x0 0x3000000 0x400000>;
+		};
+		partition@5 {	/* for testing purpose */
+			label = "nand-misc";
+			reg = <0x0 0x3400000 0xfcc00000>;
+		};
+	};
+	nand@1 {
+		reg = <0x1>;
+		#address-cells = <0x2>;
+		#size-cells = <0x1>;
+		nand-ecc-mode = "soft";
+		nand-ecc-algo = "bch";
+		nand-rb = <0>;
+		label = "main-storage-1";
+		nand-ecc-step-size = <1024>;
+		nand-ecc-strength = <24>;
+
+		partition@0 {	/* for testing purpose */
+			label = "nand1-fsbl-uboot";
+			reg = <0x0 0x0 0x400000>;
+		};
+		partition@1 {	/* for testing purpose */
+			label = "nand1-linux";
+			reg = <0x0 0x400000 0x1400000>;
+		};
+		partition@2 {	/* for testing purpose */
+			label = "nand1-device-tree";
+			reg = <0x0 0x1800000 0x400000>;
+		};
+		partition@3 {	/* for testing purpose */
+			label = "nand1-rootfs";
+			reg = <0x0 0x1c00000 0x1400000>;
+		};
+		partition@4 {	/* for testing purpose */
+			label = "nand1-bitstream";
+			reg = <0x0 0x3000000 0x400000>;
+		};
+		partition@5 {	/* for testing purpose */
+			label = "nand1-misc";
+			reg = <0x0 0x3400000 0xfcc00000>;
+		};
+	};
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_can0_default: can0-default {
+		mux {
+			function = "can0";
+			groups = "can0_9_grp";
+		};
+
+		conf {
+			groups = "can0_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO38";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO39";
+			bias-disable;
+		};
+	};
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_8_grp";
+		};
+
+		conf {
+			groups = "can1_8_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO33";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO32";
+			bias-disable;
+		};
+	};
+
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_1_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_1_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_6_grp", "gpio0_7_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_6_grp", "gpio0_7_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_10_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_10_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO42";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO43";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_10_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_10_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO41";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO40";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+
+		conf {
+			groups = "usb1_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			       "MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_gem2_default: gem2-default {
+		mux {
+			function = "ethernet2";
+			groups = "ethernet2_0_grp";
+		};
+
+		conf {
+			groups = "ethernet2_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO58", "MIO59", "MIO60", "MIO61", "MIO62",
+									"MIO63";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO52", "MIO53", "MIO54", "MIO55", "MIO56",
+									"MIO57";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio2";
+			groups = "mdio2_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio2_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_nand0_default: nand0-default {
+		mux {
+			groups = "nand0_0_grp";
+			function = "nand0";
+		};
+
+		conf {
+			groups = "nand0_0_grp";
+			bias-pull-up;
+		};
+
+		mux-ce {
+			groups = "nand0_ce_0_grp";
+			function = "nand0_ce";
+		};
+
+		conf-ce {
+			groups = "nand0_ce_0_grp";
+			bias-pull-up;
+		};
+
+		mux-rb {
+			groups = "nand0_rb_0_grp";
+			function = "nand0_rb";
+		};
+
+		conf-rb {
+			groups = "nand0_rb_0_grp";
+			bias-pull-up;
+		};
+
+		mux-dqs {
+			groups = "nand0_dqs_0_grp";
+			function = "nand0_dqs";
+		};
+
+		conf-dqs {
+			groups = "nand0_dqs_0_grp";
+			bias-pull-up;
+		};
+	};
+
+	pinctrl_spi0_default: spi0-default {
+		mux {
+			groups = "spi0_0_grp";
+			function = "spi0";
+		};
+
+		conf {
+			groups = "spi0_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
+							"spi0_ss_2_grp";
+			function = "spi0_ss";
+		};
+
+		conf-cs {
+			groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
+							"spi0_ss_2_grp";
+			bias-disable;
+		};
+	};
+
+	pinctrl_spi1_default: spi1-default {
+		mux {
+			groups = "spi1_3_grp";
+			function = "spi1";
+		};
+
+		conf {
+			groups = "spi1_3_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
+							"spi1_ss_11_grp";
+			function = "spi1_ss";
+		};
+
+		conf-cs {
+			groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
+							"spi1_ss_11_grp";
+			bias-disable;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -122,6 +495,8 @@
 &spi0 {
 	status = "okay";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0_default>;
 
 	spi0_flash0: flash@0 {
 		#address-cells = <1>;
@@ -131,7 +506,7 @@
 		reg = <0>;
 
 		partition@0 {
-			label = "data";
+			label = "spi0-data";
 			reg = <0x0 0x100000>;
 		};
 	};
@@ -140,6 +515,8 @@
 &spi1 {
 	status = "okay";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
 
 	spi1_flash0: flash@0 {
 		#address-cells = <1>;
@@ -149,7 +526,7 @@
 		reg = <0>;
 
 		partition@0 {
-			label = "data";
+			label = "spi1-data";
 			reg = <0x0 0x84000>;
 		};
 	};
@@ -158,13 +535,23 @@
 /* ULPI SMSC USB3320 */
 &usb1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_default>;
+};
+
+&dwc3_1 {
+	status = "okay";
 	dr_mode = "host";
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm017-dc3
  *
- * (C) Copyright 2016 - 2019, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -11,6 +11,7 @@
 
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/phy/phy.h>
 
 / {
 	model = "ZynqMP zc1751-xm017-dc3 RevA";
@@ -24,6 +25,8 @@
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
@@ -35,6 +38,18 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
 	};
+
+	clock_si5338_2: clk26 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clock_si5338_3: clk125 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
 };
 
 &fpd_dma_chan1 {
@@ -107,6 +122,70 @@
 	clock-frequency = <400000>;
 };
 
+/* MT29F64G08AECDBJ4-6 */
+&nand0 {
+	status = "okay";
+	arasan,has-mdma;
+	num-cs = <2>;
+
+	partition@0 {	/* for testing purpose */
+		label = "nand-fsbl-uboot";
+		reg = <0x0 0x0 0x400000>;
+	};
+	partition@1 {	/* for testing purpose */
+		label = "nand-linux";
+		reg = <0x0 0x400000 0x1400000>;
+	};
+	partition@2 {	/* for testing purpose */
+		label = "nand-device-tree";
+		reg = <0x0 0x1800000 0x400000>;
+	};
+	partition@3 {	/* for testing purpose */
+		label = "nand-rootfs";
+		reg = <0x0 0x1C00000 0x1400000>;
+	};
+	partition@4 {	/* for testing purpose */
+		label = "nand-bitstream";
+		reg = <0x0 0x3000000 0x400000>;
+	};
+	partition@5 {	/* for testing purpose */
+		label = "nand-misc";
+		reg = <0x0 0x3400000 0xFCC00000>;
+	};
+
+	partition@6 {	/* for testing purpose */
+		label = "nand1-fsbl-uboot";
+		reg = <0x1 0x0 0x400000>;
+	};
+	partition@7 {	/* for testing purpose */
+		label = "nand1-linux";
+		reg = <0x1 0x400000 0x1400000>;
+	};
+	partition@8 {	/* for testing purpose */
+		label = "nand1-device-tree";
+		reg = <0x1 0x1800000 0x400000>;
+	};
+	partition@9 {	/* for testing purpose */
+		label = "nand1-rootfs";
+		reg = <0x1 0x1C00000 0x1400000>;
+	};
+	partition@10 {	/* for testing purpose */
+		label = "nand1-bitstream";
+		reg = <0x1 0x3000000 0x400000>;
+	};
+	partition@11 {	/* for testing purpose */
+		label = "nand1-misc";
+		reg = <0x1 0x3400000 0xFCC00000>;
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* usb3, sata */
+	clocks = <&clock_si5338_2>, <&clock_si5338_3>;
+	clock-names = "ref2", "ref3";
+};
+
 &rtc {
 	status = "okay";
 };
@@ -122,6 +201,8 @@
 	ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 2 PHY_TYPE_SATA 0 3>;
 };
 
 &sdhci1 { /* emmc with some settings */
@@ -140,11 +221,27 @@
 
 &usb0 {
 	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 0 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 /* ULPI SMSC USB3320 */
 &usb1 {
 	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
+};
+
+&dwc3_1 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm018-dc4
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -26,6 +26,7 @@
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -151,6 +152,10 @@
 	status = "okay";
 };
 
+&gpu {
+	status = "okay";
+};
+
 &i2c0 {
 	clock-frequency = <400000>;
 	status = "okay";
@@ -161,6 +166,35 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -176,3 +210,11 @@
 &watchdog0 {
 	status = "okay";
 };
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm019-dc5
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Siva Durga Prasad <siva.durga.paladugu@xilinx.com>
  * Michal Simek <michal.simek@xilinx.com>
@@ -13,6 +13,7 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 
 / {
 	model = "ZynqMP zc1751-xm019-dc5 RevA";
@@ -74,6 +75,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem1_default>;
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
@@ -85,41 +88,366 @@
 
 &i2c0 {
 	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 74 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 75 GPIO_ACTIVE_HIGH>;
 };
 
 &i2c1 {
 	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 76 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 77 GPIO_ACTIVE_HIGH>;
+
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_18_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_18_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_74_grp", "gpio0_75_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_74_grp", "gpio0_75_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_19_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_19_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_76_grp", "gpio0_77_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_76_grp", "gpio0_77_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_17_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO71";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_18_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_18_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO73";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO72";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem1_default: gem1-default {
+		mux {
+			function = "ethernet1";
+			groups = "ethernet1_0_grp";
+		};
+
+		conf {
+			groups = "ethernet1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO44", "MIO45", "MIO46", "MIO47", "MIO48",
+									"MIO49";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO38", "MIO39", "MIO40", "MIO41", "MIO42",
+									"MIO43";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio1";
+			groups = "mdio1_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_0_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio0_cd_0_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "sdio0_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio0_wp_0_grp";
+			function = "sdio0_wp";
+		};
+
+		conf-wp {
+			groups = "sdio0_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_watchdog0_default: watchdog0-default {
+		mux-clk {
+			groups = "swdt0_clk_1_grp";
+			function = "swdt0_clk";
+		};
+
+		conf-clk {
+			groups = "swdt0_clk_1_grp";
+			bias-pull-up;
+		};
+
+		mux-rst {
+			groups = "swdt0_rst_1_grp";
+			function = "swdt0_rst";
+		};
+
+		conf-rst {
+			groups = "swdt0_rst_1_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc0_default: ttc0-default {
+		mux-clk {
+			groups = "ttc0_clk_0_grp";
+			function = "ttc0_clk";
+		};
+
+		conf-clk {
+			groups = "ttc0_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc0_wav_0_grp";
+			function = "ttc0_wav";
+		};
+
+		conf-wav {
+			groups = "ttc0_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc1_default: ttc1-default {
+		mux-clk {
+			groups = "ttc1_clk_0_grp";
+			function = "ttc1_clk";
+		};
+
+		conf-clk {
+			groups = "ttc1_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc1_wav_0_grp";
+			function = "ttc1_wav";
+		};
+
+		conf-wav {
+			groups = "ttc1_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc2_default: ttc2-default {
+		mux-clk {
+			groups = "ttc2_clk_0_grp";
+			function = "ttc2_clk";
+		};
+
+		conf-clk {
+			groups = "ttc2_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc2_wav_0_grp";
+			function = "ttc2_wav";
+		};
+
+		conf-wav {
+			groups = "ttc2_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc3_default: ttc3-default {
+		mux-clk {
+			groups = "ttc3_clk_0_grp";
+			function = "ttc3_clk";
+		};
+
+		conf-clk {
+			groups = "ttc3_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc3_wav_0_grp";
+			function = "ttc3_wav";
+		};
+
+		conf-wav {
+			groups = "ttc3_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
 };
 
 &sdhci0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
 	no-1-8-v;
+	xlnx,mio-bank = <0>;
 };
 
 &ttc0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc0_default>;
 };
 
 &ttc1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc1_default>;
 };
 
 &ttc2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc2_default>;
 };
 
 &ttc3 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc3_default>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 &watchdog0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_watchdog0_default>;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU100 revC
  *
- * (C) Copyright 2016 - 2019, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  * Nathalie Chan King Choy
@@ -15,6 +15,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -29,6 +30,8 @@
 		serial2 = &dcc;
 		spi0 = &spi0;
 		spi1 = &spi1;
+		usb0 = &usb0;
+		usb1 = &usb1;
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
 	};
@@ -55,6 +58,15 @@
 		};
 	};
 
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
+			      <&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>,
+			      <&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>,
+			      <&xilinx_ams 9>, <&xilinx_ams 10>,
+			      <&xilinx_ams 11>, <&xilinx_ams 12>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		led-ds2 {
@@ -90,6 +102,15 @@
 		};
 	};
 
+	ltc2954: ltc2954 { /* U7 */
+		compatible = "lltc,ltc2954", "lltc,ltc2952";
+		status = "disabled";
+		trigger-gpios = <&gpio 26 GPIO_ACTIVE_LOW>; /* INT line - input */
+		/* If there is HW watchdog on mezzanine this signal should be connected there */
+		watchdog-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; /* MIO on PAD */
+		kill-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; /* KILL signal - output */
+	};
+
 	wmmcsdio_fixed: fixedregulator-mmcsdio {
 		compatible = "regulator-fixed";
 		regulator-name = "wmmcsdio_fixed";
@@ -110,13 +131,13 @@
 		io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
 	};
 
-	si5335a_0: clk26 {
+	si5335_0: si5335_0 { /* clk0_usb - u23 */
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <26000000>;
 	};
 
-	si5335a_1: clk27 {
+	si5335_1: si5335_1 { /* clk1_dp - u23 */
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <27000000>;
@@ -158,8 +179,17 @@
 			  "", "", "", "";
 };
 
+&gpu {
+	status = "okay";
+};
+
 &i2c1 {
 	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
 	clock-frequency = <100000>;
 	i2c-mux@75 { /* u11 */
 		compatible = "nxp,pca9548";
@@ -237,10 +267,231 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_1_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_1_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_4_grp", "gpio0_5_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_4_grp", "gpio0_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_3_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_3_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio0_cd_0_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "sdio0_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_2_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_2_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_spi0_default: spi0-default {
+		mux {
+			groups = "spi0_3_grp";
+			function = "spi0";
+		};
+
+		conf {
+			groups = "spi0_3_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi0_ss_9_grp";
+			function = "spi0_ss";
+		};
+
+		conf-cs {
+			groups = "spi0_ss_9_grp";
+			bias-disable;
+		};
+
+	};
+
+	pinctrl_spi1_default: spi1-default {
+		mux {
+			groups = "spi1_0_grp";
+			function = "spi1";
+		};
+
+		conf {
+			groups = "spi1_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi1_ss_0_grp";
+			function = "spi1_ss";
+		};
+
+		conf-cs {
+			groups = "spi1_ss_0_grp";
+			bias-disable;
+		};
+
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_0_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO3";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO2";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_0_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO1";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO0";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+
+		conf {
+			groups = "usb1_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			       "MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+};
+
 &psgtr {
 	status = "okay";
-	/* usb3, dps */
-	clocks = <&si5335a_0>, <&si5335a_1>;
+	/* usb3, dp */
+	clocks = <&si5335_0>, <&si5335_1>;
 	clock-names = "ref0", "ref1";
 };
 
@@ -253,12 +504,16 @@
 	status = "okay";
 	no-1-8-v;
 	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
 	xlnx,mio-bank = <0>;
 };
 
 &sdhci1 {
 	status = "okay";
 	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <0>;
 	non-removable;
 	disable-wp;
@@ -279,16 +534,22 @@
 	status = "okay";
 	label = "LS-SPI0";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0_default>;
 };
 
 &spi1 { /* High Speed connector */
 	status = "okay";
 	label = "HS-SPI1";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 	bluetooth {
 		compatible = "ti,wl1831-st";
 		enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
@@ -297,25 +558,52 @@
 
 &uart1 {
 	status = "okay";
-
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "peripheral";
+	maximum-speed = "super-speed";
 };
 
 /* ULPI SMSC USB3320 */
 &usb1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
+};
+
+&dwc3_1 {
+	status = "okay";
 	dr_mode = "host";
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
 	status = "okay";
 };
 
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
 &zynqmp_dpdma {
 	status = "okay";
 };
@@ -326,3 +614,20 @@
 	phys = <&psgtr 1 PHY_TYPE_DP 0 1>,
 	       <&psgtr 0 PHY_TYPE_DP 1 1>;
 };
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
+};
+
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU102 Rev1.0
  *
- * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ * (C) Copyright 2016 - 2020, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 Rev1.1
+ *
+ * (C) Copyright 2016 - 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-zcu102-rev1.0.dts"
+
+/ {
+	model = "ZynqMP ZCU102 Rev1.1";
+	compatible = "xlnx,zynqmp-zcu102-rev1.1", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU102 RevA
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -13,6 +13,7 @@
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -24,10 +25,13 @@
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -150,6 +154,8 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
@@ -192,22 +198,36 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@21 {
 		reg = <21>;
 		ti,rx-internal-delay = <0x8>;
 		ti,tx-internal-delay = <0xa>;
 		ti,fifo-depth = <0x1>;
 		ti,dp83867-rxctrl-strap-quirk;
+		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
 	};
 };
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
+};
+
+&gpu {
+	status = "okay";
 };
 
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u97: gpio@20 {
 		compatible = "ti,tca6416";
@@ -451,7 +471,6 @@
 				status = "disabled"; /* unreachable */
 				reg = <0x20>;
 			};
-
 			max20751@72 { /* u95 */
 				compatible = "maxim,max20751";
 				reg = <0x72>;
@@ -468,6 +487,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	/* PL i2c via PCA9306 - u45 */
 	i2c-mux@74 { /* u34 */
@@ -580,7 +604,26 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
-			/* SI5328 - u20 */
+			si5328: clock-generator@69 {/* SI5328 - u20 */
+				compatible = "silabs,si5328";
+				reg = <0x69>;
+				/*
+				 * Chip has interrupt present connected to PL
+				 * interrupt-parent = <&>;
+				 * interrupts = <>;
+				 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#clock-cells = <1>;
+				clocks = <&refhdmi>;
+				clock-names = "xtal";
+				clock-output-names = "si5328";
+
+				si5328_clk: clk0@0 {
+					reg = <0>;
+					clock-frequency = <27000000>;
+				};
+			};
 		};
 		/* 5 - 7 unconnected */
 	};
@@ -642,6 +685,272 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio1_wp_0_grp";
+			function = "sdio1_wp";
+		};
+
+		conf-wp {
+			groups = "sdio1_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux-sw {
+			function = "gpio0";
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+		};
+
+		conf-sw {
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-msp {
+			function = "gpio0";
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+		};
+
+		conf-msp {
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-pull-up {
+			pins = "MIO22", "MIO23";
+			bias-pull-up;
+		};
+
+		conf-pull-none {
+			pins = "MIO13", "MIO38";
+			bias-disable;
+		};
+	};
+};
+
 &pcie {
 	status = "okay";
 };
@@ -653,6 +962,36 @@
 	clock-names = "ref0", "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -668,35 +1007,67 @@
 	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
-	phy-names = "sata-phy";
-	phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
+/*	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; */
 };
 
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	/*
+	 * 1.0 revision has level shifter and this property should be
+	 * removed for supporting UHS mode
+	 */
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
 	status = "okay";
 };
 
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
 &zynqmp_dpdma {
 	status = "okay";
 };
@@ -706,3 +1077,19 @@
 	phy-names = "dp-phy0";
 	phys = <&psgtr 1 PHY_TYPE_DP 0 3>;
 };
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU102 RevB
  *
- * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ * (C) Copyright 2016 - 2020, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -22,6 +22,7 @@
 		ti,tx-internal-delay = <0xa>;
 		ti,fifo-depth = <0x1>;
 		ti,dp83867-rxctrl-strap-quirk;
+		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
 	};
 	/* Cleanup from RevA */
 	/delete-node/ ethernet-phy@21;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU104
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -12,6 +12,7 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -22,10 +23,13 @@
 		ethernet0 = &gem3;
 		i2c0 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -59,16 +63,52 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
 	status = "okay";
 };
 
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
 &gem3 {
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -82,9 +122,18 @@
 	status = "okay";
 };
 
+&gpu {
+	status = "okay";
+};
+
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	/* Another connection to this bus via PL i2c via PCA9306 - u45 */
 	i2c-mux@74 { /* u34 */
@@ -104,7 +153,7 @@
 			 * 512B - 768B address 0x56
 			 * 768B - 1024B address 0x57
 			 */
-			eeprom@54 { /* u23 */
+			eeprom: eeprom@54 { /* u23 */
 				compatible = "atmel,24c08";
 				reg = <0x54>;
 				#address-cells = <1>;
@@ -116,20 +165,20 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
-				reg = <0x6c>;
-			};
+			/* 8T49N287 - u182 */
 		};
 
 		i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
-				reg = <0x43>;
+			irps5401_43: irps5401@43 { /* IRPS5401 - u175 */
+				compatible = "infineon,irps5401";
+				reg = <0x43>; /* pmbus / i2c 0x13 */
 			};
-			irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
-				reg = <0x4d>;
+			irps5401_44: irps5401@44 { /* IRPS5401 - u180 */
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* pmbus / i2c 0x14 */
 			};
 		};
 
@@ -173,8 +222,204 @@
 	};
 };
 
-&rtc {
+&pinctrl0 {
 	status = "okay";
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+			drive-strength = <12>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
 };
 
 &psgtr {
@@ -184,6 +429,39 @@
 	clock-names = "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
@@ -203,28 +481,56 @@
 &sdhci1 {
 	status = "okay";
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 	disable-wp;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
 	status = "okay";
 };
 
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
 &zynqmp_dpdma {
 	status = "okay";
 };
@@ -235,3 +541,19 @@
 	phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
 	       <&psgtr 0 PHY_TYPE_DP 1 3>;
 };
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -1,8 +1,8 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0+
 /*
  * dts file for Xilinx ZynqMP ZCU104
  *
- * (C) Copyright 2017 - 2020, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -12,6 +12,7 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -22,10 +23,13 @@
 		ethernet0 = &gem3;
 		i2c0 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -64,6 +68,8 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
@@ -106,6 +112,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -119,9 +127,18 @@
 	status = "okay";
 };
 
+&gpu {
+	status = "okay";
+};
+
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u97: gpio@20 {
 		compatible = "ti,tca6416";
@@ -172,9 +189,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
-				reg = <0x6c>;
-			};
+			/* 8T49N287 - u182 */
 		};
 
 		i2c@2 {
@@ -219,6 +234,213 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+			drive-strength = <12>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* nc, sata, usb3, dp */
+	clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
+	clock-names = "ref1", "ref2", "ref3";
+};
+
 &qspi {
 	status = "okay";
 	flash@0 {
@@ -226,6 +448,25 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
 	};
 };
 
@@ -233,13 +474,6 @@
 	status = "okay";
 };
 
-&psgtr {
-	status = "okay";
-	/* nc, sata, usb3, dp */
-	clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
-	clock-names = "ref1", "ref2", "ref3";
-};
-
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
@@ -259,28 +493,56 @@
 &sdhci1 {
 	status = "okay";
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 	disable-wp;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
 	status = "okay";
 };
 
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};
+
 &zynqmp_dpdma {
 	status = "okay";
 };
@@ -291,3 +553,19 @@
 	phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
 	       <&psgtr 0 PHY_TYPE_DP 1 3>;
 };
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU106
  *
- * (C) Copyright 2016 - 2019, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -13,6 +13,7 @@
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -24,10 +25,13 @@
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -150,24 +154,14 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
 	status = "okay";
 };
 
-&zynqmp_dpdma {
-	status = "okay";
-};
-
-&zynqmp_dpsub {
-	status = "okay";
-	phy-names = "dp-phy0", "dp-phy1";
-	phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
-	       <&psgtr 0 PHY_TYPE_DP 1 3>;
-};
-
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
 &fpd_dma_chan1 {
 	status = "okay";
 };
@@ -204,6 +198,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -215,11 +211,22 @@
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
+};
+
+&gpu {
+	status = "okay";
 };
 
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u97: gpio@20 {
 		compatible = "ti,tca6416";
@@ -478,6 +485,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	/* PL i2c via PCA9306 - u45 */
 	i2c-mux@74 { /* u34 */
@@ -581,7 +593,26 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
-			/* SI5328 - u20 */
+			si5328: clock-generator@69 {/* SI5328 - u20 */
+				compatible = "silabs,si5328";
+				reg = <0x69>;
+				/*
+				 * Chip has interrupt present connected to PL
+				 * interrupt-parent = <&>;
+				 * interrupts = <>;
+				 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#clock-cells = <1>;
+				clocks = <&refhdmi>;
+				clock-names = "xtal";
+				clock-output-names = "si5328";
+
+				si5328_clk: clk0@0 {
+					reg = <0>;
+					clock-frequency = <27000000>;
+				};
+			};
 		};
 		i2c@5 {
 			#address-cells = <1>;
@@ -652,6 +683,272 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio1_wp_0_grp";
+			function = "sdio1_wp";
+		};
+
+		conf-wp {
+			groups = "sdio1_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux {
+			function = "gpio0";
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+		};
+
+		conf {
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-msp {
+			function = "gpio0";
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+		};
+
+		conf-msp {
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-pull-up {
+			pins = "MIO22";
+			bias-pull-up;
+		};
+
+		conf-pull-none {
+			pins = "MIO13", "MIO23", "MIO38";
+			bias-disable;
+		};
+	};
+};
+
 &psgtr {
 	status = "okay";
 	/* nc, sata, usb3, dp */
@@ -659,6 +956,36 @@
 	clock-names = "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -681,24 +1008,70 @@
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
 	status = "okay";
 };
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
+	       <&psgtr 0 PHY_TYPE_DP 1 3>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU111
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -13,6 +13,7 @@
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -24,9 +25,12 @@
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -166,6 +170,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -177,11 +183,22 @@
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
+};
+
+&gpu {
+	status = "okay";
 };
 
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u22: gpio@20 {
 		compatible = "ti,tca6416";
@@ -326,13 +343,16 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
+			irps5401_43: irps5401@43 { /* IRPS5401 - u53 check these */
+				compatible = "infineon,irps5401";
 				reg = <0x43>;
 			};
-			irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
+			irps5401_44: irps5401@44 { /* IRPS5401 - u55 */
+				compatible = "infineon,irps5401";
 				reg = <0x44>;
 			};
-			irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
+			irps5401_45: irps5401@45 { /* IRPS5401 - u57 */
+				compatible = "infineon,irps5401";
 				reg = <0x45>;
 			};
 			/* u68 IR38064 +0 */
@@ -354,6 +374,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	i2c-mux@74 { /* u26 */
 		compatible = "nxp,pca9548";
@@ -455,9 +480,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
-			si5382: clock-generator@69 { /* SI5382 - u48 */
-				reg = <0x69>;
-			};
+			/* SI5382 - u48 */
 		};
 		i2c@5 {
 			#address-cells = <1>;
@@ -542,13 +565,250 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+			drive-strength = <12>;
+			slew-rate = <SLEW_RATE_FAST>;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+			drive-strength = <4>;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux {
+			function = "gpio0";
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+		};
+
+		conf {
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-msp {
+			function = "gpio0";
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+		};
+
+		conf-msp {
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-pull-up {
+			pins = "MIO22";
+			bias-pull-up;
+		};
+
+		conf-pull-none {
+			pins = "MIO13", "MIO23", "MIO38";
+			bias-disable;
+		};
+	};
+};
+
 &psgtr {
 	status = "okay";
-	/* nc, sata, usb3, dp */
-	clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+	/* nc, dp, usb3, sata */
+	clocks = <&si5341 0 0>, <&si5341 0 2>, <&si5341 0 3>;
 	clock-names = "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -565,24 +825,42 @@
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
 	phy-names = "sata-phy";
-	phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
 };
 
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	disable-wp;
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
 	no-1-8-v;
 	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &zynqmp_dpdma {
@@ -595,3 +873,19 @@
 	phys = <&psgtr 1 PHY_TYPE_DP 0 1>,
 	       <&psgtr 0 PHY_TYPE_DP 1 1>;
 };
+
+&zynqmp_dp_snd_pcm0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+	status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU1275
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+	model = "ZynqMP ZCU1275 RevA";
+	compatible = "xlnx,zynqmp-zcu1275-revA", "xlnx,zynqmp-zcu1275",
+		     "xlnx,zynqmp";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revB.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZCU1275 RevB
+ *
+ * (C) Copyright 2018 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+	model = "ZynqMP ZCU1275 RevB";
+	compatible = "xlnx,zynqmp-zcu1275-revB", "xlnx,zynqmp-zcu1275",
+		     "xlnx,zynqmp";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		mmc0 = &sdhci1;
+		ethernet0 = &gem1;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gem1 {
+	status = "okay";
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy1: ethernet-phy@1 {
+			reg = <1>; /* KSZ9031RNXIC on AES-FMC-NETW1-G */
+			rxc-skew-ps = <1800>; /* Skew control of RX_CLK pad output */
+			txc-skew-ps = <1800>; /* Skew control of GTX_CLK pad input */
+			txen-skew-ps = <900>; /* Skew control of TX_CTL pad input */
+			rxdv-skew-ps = <0>; /* Skew control of RX_CTL pad output */
+			rxd0-skew-ps = <0>; /* Skew control of RXD0 pad output */
+			rxd1-skew-ps = <0>; /* Skew control of RXD1 pad output */
+			rxd2-skew-ps = <0>; /* Skew control of RXD2 pad output */
+			rxd3-skew-ps = <0>; /* Skew control of RXD3 pad output */
+			txd0-skew-ps = <900>; /* Skew control of TXD0 pad input */
+			txd1-skew-ps = <900>; /* Skew control of TXD1 pad input */
+			txd2-skew-ps = <900>; /* Skew control of TXD2 pad input */
+			txd3-skew-ps = <900>; /* Skew control of TXD3 pad input */
+		};
+	};
+};
+
+&gpio {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <1>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@0 { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@100000 { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@600000 { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@620000 { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+	/*
+	 * 1.0 revision has level shifter and this property should be
+	 * removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	xlnx,mio-bank = <1>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu1285-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu1285-revA.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZCU1285 RevA
+ *
+ * (C) Copyright 2018 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+	model = "ZynqMP ZCU1285 RevA";
+	compatible = "xlnx,zynqmp-zcu1285-revA", "xlnx,zynqmp-zcu1285",
+		     "xlnx,zynqmp";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		mmc0 = &sdhci1;
+		ethernet0 = &gem1; /* EMIO */
+		i2c = &i2c0; /* EMIO */
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ina226-u60 {
+		compatible = "iio-hwmon";
+		io-channels = <&u60 0>, <&u60 1>, <&u60 2>, <&u60 3>;
+	};
+	ina226-u61 {
+		compatible = "iio-hwmon";
+		io-channels = <&u61 0>, <&u61 1>, <&u61 2>, <&u61 3>;
+	};
+	ina226-u63 {
+		compatible = "iio-hwmon";
+		io-channels = <&u63 0>, <&u63 1>, <&u63 2>, <&u63 3>;
+	};
+	ina226-u65 {
+		compatible = "iio-hwmon";
+		io-channels = <&u65 0>, <&u65 1>, <&u65 2>, <&u65 3>;
+	};
+	ina226-u64 {
+		compatible = "iio-hwmon";
+		io-channels = <&u64 0>, <&u64 1>, <&u64 2>, <&u64 3>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PMBUS */
+			max20751@74 { /* u23 */
+				compatible = "maxim,max20751";
+				reg = <0x74>;
+			};
+			max20751@70 { /* u89 */
+				compatible = "maxim,max20751";
+				reg = <0x70>;
+			};
+			max15301@a { /* u28 */
+				compatible = "maxim,max15301";
+				reg = <0xa>;
+			};
+			max15303@b { /* u48 */
+				compatible = "maxim,max15303";
+				reg = <0xb>;
+			};
+			max15303@d { /* u27 */
+				compatible = "maxim,max15303";
+				reg = <0xd>;
+			};
+			max15303@e { /* u11 */
+				compatible = "maxim,max15303";
+				reg = <0xe>;
+			};
+			max15303@f { /* u96 */
+				compatible = "maxim,max15303";
+				reg = <0xf>;
+			};
+			max15303@11 { /* u47 */
+				compatible = "maxim,max15303";
+				reg = <0x11>;
+			};
+			max15303@12 { /* u24 */
+				compatible = "maxim,max15303";
+				reg = <0x12>;
+			};
+			max15301@13 { /* u29 */
+				compatible = "maxim,max15301";
+				reg = <0x13>;
+			};
+			max15303@14 { /* u51 */
+				compatible = "maxim,max15303";
+				reg = <0x14>;
+			};
+			max15303@15 { /* u30 */
+				compatible = "maxim,max15303";
+				reg = <0x15>;
+			};
+			max15303@16 { /* u102 */
+				compatible = "maxim,max15303";
+				reg = <0x16>;
+			};
+			max15301@17 { /* u50 */
+				compatible = "maxim,max15301";
+				reg = <0x17>;
+			};
+			max15301@18 { /* u31 */
+				compatible = "maxim,max15301";
+				reg = <0x18>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* CM_I2C */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYS_EEPROM */
+			eeprom: eeprom@54 { /* u101 */
+				compatible = "atmel,24c32"; /* 24LC32A */
+				reg = <0x54>;
+			};
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FMC1 */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* FMC2 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* ANALOG_PMBUS */
+			u60: ina226@40 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u60";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+			u61: ina226@41 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u61";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+			u63: ina226@42 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u63";
+				reg = <0x42>;
+				shunt-resistor = <1000>;
+			};
+			u65: ina226@43 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u65";
+				reg = <0x43>;
+				shunt-resistor = <1000>;
+			};
+			u64: ina226@44 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u64";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* ANALOG_CM_I2C */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* FMC3 */
+		};
+	};
+};
+
+&gem1 {
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy1: ethernet-phy@1 {
+			reg = <1>; /* KSZ9031RNXIC on AES-FMC-NETW1-G */
+			rxc-skew-ps = <1800>; /* Skew control of RX_CLK pad output */
+			txc-skew-ps = <1800>; /* Skew control of GTX_CLK pad input */
+			txen-skew-ps = <900>; /* Skew control of TX_CTL pad input */
+			rxdv-skew-ps = <0>; /* Skew control of RX_CTL pad output */
+			rxd0-skew-ps = <0>; /* Skew control of RXD0 pad output */
+			rxd1-skew-ps = <0>; /* Skew control of RXD1 pad output */
+			rxd2-skew-ps = <0>; /* Skew control of RXD2 pad output */
+			rxd3-skew-ps = <0>; /* Skew control of RXD3 pad output */
+			txd0-skew-ps = <900>; /* Skew control of TXD0 pad input */
+			txd1-skew-ps = <900>; /* Skew control of TXD1 pad input */
+			txd2-skew-ps = <900>; /* Skew control of TXD2 pad input */
+			txd3-skew-ps = <900>; /* Skew control of TXD3 pad input */
+		};
+	};
+};
+
+&gpio {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <1>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	xlnx,mio-bank = <1>;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu208-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu208-revA.dts
@@ -0,0 +1,704 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU208
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU208 RevA";
+	compatible = "xlnx,zynqmp-zcu208-revA", "xlnx,zynqmp-zcu208", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		sw19 {
+			label = "sw19";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_DOWN>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat_led {
+			label = "heartbeat";
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	ina226-vccint {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint 0>, <&vccint 1>, <&vccint 2>, <&vccint 3>;
+	};
+	ina226-vccint-io-bram-ps {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_io_bram_ps 0>, <&vccint_io_bram_ps 1>, <&vccint_io_bram_ps 2>, <&vccint_io_bram_ps 3>;
+	};
+	ina226-vcc1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v8 0>, <&vcc1v8 1>, <&vcc1v8 2>, <&vcc1v8 3>;
+	};
+	ina226-vcc1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2 0>, <&vcc1v2 1>, <&vcc1v2 2>, <&vcc1v2 3>;
+	};
+	ina226-vadj-fmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vadj_fmc 0>, <&vadj_fmc 1>, <&vadj_fmc 2>, <&vadj_fmc 3>;
+	};
+	ina226-mgtavcc {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtavcc 0>, <&mgtavcc 1>, <&mgtavcc 2>, <&mgtavcc 3>;
+	};
+	ina226-mgt1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v2 0>, <&mgt1v2 1>, <&mgt1v2 2>, <&mgt1v2 3>;
+	};
+	ina226-mgt1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v8 0>, <&mgt1v8 1>, <&mgt1v8 2>, <&mgt1v8 3>;
+	};
+	ina226-vccint-ams {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_ams 0>, <&vccint_ams 1>, <&vccint_ams 2>, <&vccint_ams 3>;
+	};
+	ina226-dac-avtt {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avtt 0>, <&dac_avtt 1>, <&dac_avtt 2>, <&dac_avtt 3>;
+	};
+	ina226-dac-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avccaux 0>, <&dac_avccaux 1>, <&dac_avccaux 2>, <&dac_avccaux 3>;
+	};
+	ina226-adc-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avcc 0>, <&adc_avcc 1>, <&adc_avcc 2>, <&adc_avcc 3>;
+	};
+	ina226-adc-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avccaux 0>, <&adc_avccaux 1>, <&adc_avccaux 2>, <&adc_avccaux 3>;
+	};
+	ina226-dac-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
+	};
+
+	/* 48MHz reference crystal */
+	ref48: ref48M {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: ethernet-phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_LWR_CLK", "QSPI_LWR_DQ1", "QSPI_LWR_DQ2", "QSPI_LWR_DQ3", "QSPI_LWR_DQ0", /* 0 - 4 */
+		  "QSPI_LWR_CS_B", "", "QSPI_UPR_CS_B", "QSPI_UPR_DQ0", "QSPI_UPR_DQ1", /* 5 - 9 */
+		  "QSPI_UPR_DQ2", "QSPI_UPR_DQ3", "QSPI_UPR_CLK", "PS_GPIO2", "I2C0_SCL", /* 10 - 14 */
+		  "I2C0_SDA", "I2C1_SCL", "I2C1_SDA", "UART0_TXD", "UART0_RXD", /* 15 - 19 */
+		  "", "", "BUTTON", "LED", "", /* 20 - 24 */
+		  "", "PMU_INPUT", "", "", "", /* 25 - 29 */
+		  "", "", "PMU_GPO0", "PMU_GPO1", "PMU_GPO2", /* 30 - 34 */
+		  "PMU_GPO3", "PMU_GPO4", "PMU_GPO5", "PS_GPIO1", "SDIO_SEL", /* 35 - 39 */
+		  "SDIO_DIR_CMD", "SDIO_DIR_DAT0", "SDIO_DIR_DAT1", "", "", /* 40 - 44 */
+		  "SDIO_DETECT", "SDIO_DAT0", "SDIO_DAT1", "SDIO_DAT2", "SDIO_DAT3", /* 45 - 49 */
+		  "SDIO_CMD", "SDIO_CLK", "USB_CLK", "USB_DIR", "USB_DATA2", /* 50 - 54 */
+		  "USB_NXT", "USB_DATA0", "USB_DATA1", "USB_STP", "USB_DATA3", /* 55 - 59 */
+		  "USB_DATA4", "USB_DATA5", "USB_DATA6", "USB_DATA7", "ENET_TX_CLK", /* 60 - 64 */
+		  "ENET_TX_D0", "ENET_TX_D1", "ENET_TX_D2", "ENET_TX_D3", "ENET_TX_CTRL", /* 65 - 69 */
+		  "ENET_RX_CLK", "ENET_RX_D0", "ENET_RX_D1", "ENET_RX_D2", "ENET_RX_D3", /* 70 - 74 */
+		  "ENET_RX_CTRL", "ENET_MDC", "ENET_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+
+	tca6416_u15: gpio@20 { /* u15 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "MIO26_PMU_INPUT_LS", "DAC_AVTT_VOUT_SEL", /* 0 - 3 */
+				  "", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "FMCP_HSPC_PRSNT_M2C_B", "", "", "VCCINT_VRHOT_B", /* 10 - 13 */
+				  "", "8A34001_EXP_RST_B", "IRPS5401_ALERT_B", "INA226_PMBUS_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@75 { /* u17 */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PS_PMBUS */
+			/* PMBUS_ALERT done via pca9544 */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccint_io_bram_ps: ina226@41 { /* u57 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-io-bram-ps";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v8: ina226@42 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v8";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+			vcc1v2: ina226@43 { /* u58 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vadj_fmc: ina226@45 { /* u62 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vadj-fmc";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@46 { /* u67 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtavcc";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			mgt1v2: ina226@47 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v2";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			mgt1v8: ina226@48 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v8";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vccint_ams: ina226@49 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-ams";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+			dac_avtt: ina226@4a { /* u59 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avtt";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			dac_avccaux: ina226@4b { /* u124 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avccaux";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			adc_avcc: ina226@4c { /* u75 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avcc";
+				reg = <0x4c>;
+				shunt-resistor = <5000>;
+			};
+			adc_avccaux: ina226@4d { /* u71 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avccaux";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+			dac_avcc: ina226@4e { /* u77 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avcc";
+				reg = <0x4e>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* NC */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* u104 - ir35215 0x10/0x40 */
+			/* u127 - ir38164 0x1b/0x4b */
+			/* u112 - ir38164 0x13/0x43 */
+			/* u123 - ir38164 0x1c/0x4c */
+
+			irps5401_44: irps5401@44 { /* IRPS5401 - u53 */
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* i2c addr 0x14 */
+			};
+			irps5401_45: irps5401@45 { /* IRPS5401 - u55 */
+				compatible = "infineon,irps5401";
+				reg = <0x45>; /* i2c addr 0x15 */
+			};
+			/* J21 header too */
+
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* SYSMON */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
+	i2c-mux@74 {
+		compatible = "nxp,pca9548"; /* u20 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c-mux-idle-disconnect;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c_eeprom: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u21 */
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+		i2c_si5341: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si5341: clock-generator@36 { /* SI5341 - u43 */
+				compatible = "silabs,si5341";
+				reg = <0x36>;
+				#clock-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&ref48>;
+				clock-names = "xtal";
+				clock-output-names = "si5341";
+
+				si5341_2: out@2 {
+					/* refclk2 for PS-GT, used for USB3 */
+					reg = <2>;
+					always-on;
+				};
+				si5341_3: out@3 {
+					/* refclk3 for PS-GT, used for SATA */
+					reg = <3>;
+					always-on;
+				};
+				si5341_5: out@5 {
+					/* refclk5 PL CLK100 */
+					reg = <5>;
+					always-on;
+				};
+				si5341_6: out@6 {
+					/* refclk6 PL CLK125 */
+					reg = <6>;
+					always-on;
+				};
+				si5341_9: out@9 {
+					/* refclk9 used for PS_REF_CLK 33.3 MHz */
+					reg = <9>;
+					always-on;
+				};
+			};
+		};
+		i2c_si570_user_c0: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_1: clock-generator@5d { /* USER C0 SI570 - u47 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c0";
+			};
+		};
+		i2c_si570_mgt: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_2: clock-generator@5d { /* USER MGT SI570 - u48 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <148500000>;
+				clock-output-names = "si570_mgt";
+			};
+		};
+		i2c_8a34001: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			idt_8a34001: phc@5b {
+				compatible = "idt,8a34001"; /* u409B */
+				reg = <0x5b>;
+			};
+		};
+		i2c_clk104: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* CLK104_SDA */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* RFMCP connector */
+		};
+		/* 7 NC */
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* FMCP_HSPC_IIC */
+		};
+		i2c_si570_user_c1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si570_3: clock-generator@5d { /* USER C1 SI570 - u130 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c1";
+			};
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYSMON */
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* DDR4 SODIMM */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* SFP3 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* SFP2 */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* SFP1 */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* SFP0 */
+		};
+	};
+	/* MSP430 */
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* U11 and U12 MT25QU02GCBBE12 1Gb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* nc, nc, usb3, sata */
+	clocks = <&si5341 0 2>, <&si5341 0 3>;
+	clock-names = "ref2", "ref3";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	disable-wp;
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	xlnx,mio-bank = <1>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu216-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu216-revA.dts
@@ -0,0 +1,708 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU216
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU216 RevA";
+	compatible = "xlnx,zynqmp-zcu216-revA", "xlnx,zynqmp-zcu216", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		sw19 {
+			label = "sw19";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_DOWN>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat_led {
+			label = "heartbeat";
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	ina226-vccint {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint 0>, <&vccint 1>, <&vccint 2>, <&vccint 3>;
+	};
+	ina226-vccint-io-bram-ps {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_io_bram_ps 0>, <&vccint_io_bram_ps 1>, <&vccint_io_bram_ps 2>, <&vccint_io_bram_ps 3>;
+	};
+	ina226-vcc1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v8 0>, <&vcc1v8 1>, <&vcc1v8 2>, <&vcc1v8 3>;
+	};
+	ina226-vcc1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2 0>, <&vcc1v2 1>, <&vcc1v2 2>, <&vcc1v2 3>;
+	};
+	ina226-vadj-fmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vadj_fmc 0>, <&vadj_fmc 1>, <&vadj_fmc 2>, <&vadj_fmc 3>;
+	};
+	ina226-mgtavcc {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtavcc 0>, <&mgtavcc 1>, <&mgtavcc 2>, <&mgtavcc 3>;
+	};
+	ina226-mgt1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v2 0>, <&mgt1v2 1>, <&mgt1v2 2>, <&mgt1v2 3>;
+	};
+	ina226-mgt1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v8 0>, <&mgt1v8 1>, <&mgt1v8 2>, <&mgt1v8 3>;
+	};
+	ina226-vccint-ams {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_ams 0>, <&vccint_ams 1>, <&vccint_ams 2>, <&vccint_ams 3>;
+	};
+	ina226-dac-avtt {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avtt 0>, <&dac_avtt 1>, <&dac_avtt 2>, <&dac_avtt 3>;
+	};
+	ina226-dac-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avccaux 0>, <&dac_avccaux 1>, <&dac_avccaux 2>, <&dac_avccaux 3>;
+	};
+	ina226-adc-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avcc 0>, <&adc_avcc 1>, <&adc_avcc 2>, <&adc_avcc 3>;
+	};
+	ina226-adc-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avccaux 0>, <&adc_avccaux 1>, <&adc_avccaux 2>, <&adc_avccaux 3>;
+	};
+	ina226-dac-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
+	};
+
+	/* 48MHz reference crystal */
+	ref48: ref48M {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* nc, nc, usb3, sata */
+	clocks = <&si5341 0 2>, <&si5341 0 3>;
+	clock-names = "ref2", "ref3";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: ethernet-phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_LWR_CLK", "QSPI_LWR_DQ1", "QSPI_LWR_DQ2", "QSPI_LWR_DQ3", "QSPI_LWR_DQ0", /* 0 - 4 */
+		  "QSPI_LWR_CS_B", "", "QSPI_UPR_CS_B", "QSPI_UPR_DQ0", "QSPI_UPR_DQ1", /* 5 - 9 */
+		  "QSPI_UPR_DQ2", "QSPI_UPR_DQ3", "QSPI_UPR_CLK", "PS_GPIO2", "I2C0_SCL", /* 10 - 14 */
+		  "I2C0_SDA", "I2C1_SCL", "I2C1_SDA", "UART0_TXD", "UART0_RXD", /* 15 - 19 */
+		  "", "", "BUTTON", "LED", "", /* 20 - 24 */
+		  "", "PMU_INPUT", "", "", "", /* 25 - 29 */
+		  "", "", "PMU_GPO0", "PMU_GPO1", "PMU_GPO2", /* 30 - 34 */
+		  "PMU_GPO3", "PMU_GPO4", "PMU_GPO5", "PS_GPIO1", "SDIO_SEL", /* 35 - 39 */
+		  "SDIO_DIR_CMD", "SDIO_DIR_DAT0", "SDIO_DIR_DAT1", "", "", /* 40 - 44 */
+		  "SDIO_DETECT", "SDIO_DAT0", "SDIO_DAT1", "SDIO_DAT2", "SDIO_DAT3", /* 45 - 49 */
+		  "SDIO_CMD", "SDIO_CLK", "USB_CLK", "USB_DIR", "USB_DATA2", /* 50 - 54 */
+		  "USB_NXT", "USB_DATA0", "USB_DATA1", "USB_STP", "USB_DATA3", /* 55 - 59 */
+		  "USB_DATA4", "USB_DATA5", "USB_DATA6", "USB_DATA7", "ENET_TX_CLK", /* 60 - 64 */
+		  "ENET_TX_D0", "ENET_TX_D1", "ENET_TX_D2", "ENET_TX_D3", "ENET_TX_CTRL", /* 65 - 69 */
+		  "ENET_RX_CLK", "ENET_RX_D0", "ENET_RX_D1", "ENET_RX_D2", "ENET_RX_D3", /* 70 - 74 */
+		  "ENET_RX_CTRL", "ENET_MDC", "ENET_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+
+	tca6416_u15: gpio@20 { /* u15 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "MIO26_PMU_INPUT_LS", "", /* 0 - 3 */
+				  "", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "FMCP_HSPC_PRSNT_M2C_B", "", "", "VCCINT_VRHOT_B", /* 10 - 13 */
+				  "", "8A34001_EXP_RST_B", "IRPS5401_ALERT_B", "INA226_PMBUS_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@75 { /* u17 */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PS_PMBUS */
+			/* PMBUS_ALERT done via pca9544 */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccint_io_bram_ps: ina226@41 { /* u57 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-io-bram-ps";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v8: ina226@42 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v8";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+			vcc1v2: ina226@43 { /* u58 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vadj_fmc: ina226@45 { /* u62 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vadj-fmc";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@46 { /* u67 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtavcc";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			mgt1v2: ina226@47 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v2";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			mgt1v8: ina226@48 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v8";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vccint_ams: ina226@49 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-ams";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+			dac_avtt: ina226@4a { /* u59 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avtt";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			dac_avccaux: ina226@4b { /* u124 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avccaux";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			adc_avcc: ina226@4c { /* u75 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avcc";
+				reg = <0x4c>;
+				shunt-resistor = <5000>;
+			};
+			adc_avccaux: ina226@4d { /* u71 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avccaux";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+			dac_avcc: ina226@4e { /* u77 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avcc";
+				reg = <0x4e>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* NC */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* u104 - ir35215 0x10/0x40 */
+			/* u127 - ir38164 0x1b/0x4b */
+			/* u112 - ir38164 0x13/0x43 */
+			/* u123 - ir38164 0x1c/0x4c */
+
+			irps5401_44: irps5401@44 { /* IRPS5401 - u53 */
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* i2c addr 0x14 */
+			};
+			irps5401_45: irps5401@45 { /* IRPS5401 - u55 */
+				compatible = "infineon,irps5401";
+				reg = <0x45>; /* i2c addr 0x15 */
+			};
+			/* J21 header too */
+
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* SYSMON */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
+	i2c-mux@74 {
+		compatible = "nxp,pca9548"; /* u20 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c-mux-idle-disconnect;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c_eeprom: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u21 */
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+		i2c_si5341: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si5341: clock-generator@36 { /* SI5341 - u43 */
+				compatible = "silabs,si5341";
+				reg = <0x36>;
+				#clock-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&ref48>;
+				clock-names = "xtal";
+				clock-output-names = "si5341";
+
+				si5341_2: out@2 {
+					/* refclk2 for PS-GT, used for USB3 */
+					reg = <2>;
+					always-on;
+				};
+				si5341_3: out@3 {
+					/* refclk3 for PS-GT, used for SATA */
+					reg = <3>;
+					always-on;
+				};
+				si5341_5: out@5 {
+					/* refclk5 PL CLK100 */
+					reg = <5>;
+					always-on;
+				};
+				si5341_6: out@6 {
+					/* refclk6 PL CLK125 */
+					reg = <6>;
+					always-on;
+				};
+				si5341_9: out@9 {
+					/* refclk9 used for PS_REF_CLK 33.3 MHz */
+					reg = <9>;
+					always-on;
+				};
+			};
+		};
+		i2c_si570_user_c0: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_1: clock-generator@5d { /* USER C0 SI570 - u47 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c0";
+			};
+		};
+		i2c_si570_mgt: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_2: clock-generator@5d { /* USER MGT SI570 - u48 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <148500000>;
+				clock-output-names = "si570_mgt";
+			};
+		};
+		i2c_8a34001: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			idt_8a34001: phc@5b {
+				compatible = "idt,8a34001"; /* u409B */
+				reg = <0x5b>;
+			};
+		};
+		i2c_clk104: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* CLK104_SDA */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* RFMCP connector */
+		};
+		/* 7 NC */
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* FMCP_HSPC_IIC */
+		};
+		i2c_si570_user_c1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si570_3: clock-generator@5d { /* USER C1 SI570 - u130 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c1";
+			};
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYSMON */
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* DDR4 SODIMM */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* SFP3 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* SFP2 */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* SFP1 */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* SFP0 */
+		};
+	};
+	/* MSP430 */
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* U11 and U12 MT25QU02GCBBE12 1Gb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	disable-wp;
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	xlnx,mio-bank = <1>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu670-revA.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu670-revA.dts
@@ -0,0 +1,659 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZCU670 (67DR)
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU670 RevA";
+	compatible = "xlnx,zynqmp-zcu670-revA", "xlnx,zynqmp-zcu670",
+		     "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x0 0x80000000>;
+		/* Another 4GB connected to PL */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		sw1 {
+			label = "sw1";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat_led {
+			label = "heartbeat"; /* DS1 */
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	ina226-vccint {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint 0>, <&vccint 1>, <&vccint 2>, <&vccint 3>;
+	};
+	ina226-vccint-io-bram-ps {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_io_bram_ps 0>, <&vccint_io_bram_ps 1>, <&vccint_io_bram_ps 2>, <&vccint_io_bram_ps 3>;
+	};
+	ina226-vcc1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v8 0>, <&vcc1v8 1>, <&vcc1v8 2>, <&vcc1v8 3>;
+	};
+	ina226-vcc1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2 0>, <&vcc1v2 1>, <&vcc1v2 2>, <&vcc1v2 3>;
+	};
+	ina226-vadj-fmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vadj_fmc 0>, <&vadj_fmc 1>, <&vadj_fmc 2>, <&vadj_fmc 3>;
+	};
+	ina226-mgtavcc {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtavcc 0>, <&mgtavcc 1>, <&mgtavcc 2>, <&mgtavcc 3>;
+	};
+	ina226-mgt1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v2 0>, <&mgt1v2 1>, <&mgt1v2 2>, <&mgt1v2 3>;
+	};
+	ina226-mgt1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v8 0>, <&mgt1v8 1>, <&mgt1v8 2>, <&mgt1v8 3>;
+	};
+	ina226-vccint-ams {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_ams 0>, <&vccint_ams 1>, <&vccint_ams 2>, <&vccint_ams 3>;
+	};
+	ina226-dac-avtt {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avtt 0>, <&dac_avtt 1>, <&dac_avtt 2>, <&dac_avtt 3>;
+	};
+	ina226-dac-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avccaux 0>, <&dac_avccaux 1>, <&dac_avccaux 2>, <&dac_avccaux 3>;
+	};
+	ina226-adc-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avcc 0>, <&adc_avcc 1>, <&adc_avcc 2>, <&adc_avcc 3>;
+	};
+	ina226-adc-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avccaux 0>, <&adc_avccaux 1>, <&adc_avccaux 2>, <&adc_avccaux 3>;
+	};
+	ina226-dac-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
+	};
+
+	/* 48MHz reference crystal */
+	ref48: ref48M {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+
+	si5381_6: si5381_6 { /* refclk_usb3 - u43 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: ethernet-phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_LWR_CLK", "QSPI_LWR_DQ1", "QSPI_LWR_DQ2", "QSPI_LWR_DQ3", "QSPI_LWR_DQ0", /* 0 - 4 */
+		  "QSPI_LWR_CS_B", "", "QSPI_UPR_CS_B", "QSPI_UPR_DQ0", "QSPI_UPR_DQ1", /* 5 - 9 */
+		  "QSPI_UPR_DQ2", "QSPI_UPR_DQ3", "QSPI_UPR_CLK", "PS_GPIO2", "I2C0_SCL", /* 10 - 14 */
+		  "I2C0_SDA", "I2C1_SCL", "I2C1_SDA", "UART0_TXD", "UART0_RXD", /* 15 - 19 */
+		  "", "", "BUTTON", "LED", "", /* 20 - 24 */
+		  "", "PMU_INPUT", "SFP3_TX_DISABLE", "SFP2_TX_DISABLE", "SFP1_TX_DISABLE", /* 25 - 29 */
+		  "SFP0_TX_DISABLE", "", "PMU_GPO0", "PMU_GPO1", "PMU_GPO2", /* 30 - 34 */
+		  "PMU_GPO3", "PMU_GPO4", "PMU_GPO5", "PS_GPIO1", "SDIO_SEL", /* 35 - 39 */
+		  "SDIO_DIR_CMD", "SDIO_DIR_DAT0", "SDIO_DIR_DAT1", "SD_PWR_RST", "", /* 40 - 44 */
+		  "SDIO_DETECT", "SDIO_DAT0", "SDIO_DAT1", "SDIO_DAT2", "SDIO_DAT3", /* 45 - 49 */
+		  "SDIO_CMD", "SDIO_CLK", "USB_CLK", "USB_DIR", "USB_DATA2", /* 50 - 54 */
+		  "USB_NXT", "USB_DATA0", "USB_DATA1", "USB_STP", "USB_DATA3", /* 55 - 59 */
+		  "USB_DATA4", "USB_DATA5", "USB_DATA6", "USB_DATA7", "ENET_TX_CLK", /* 60 - 64 */
+		  "ENET_TX_D0", "ENET_TX_D1", "ENET_TX_D2", "ENET_TX_D3", "ENET_TX_CTRL", /* 65 - 69 */
+		  "ENET_RX_CLK", "ENET_RX_D0", "ENET_RX_D1", "ENET_RX_D2", "ENET_RX_D3", /* 70 - 74 */
+		  "ENET_RX_CTRL", "ENET_MDC", "ENET_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 - 89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+
+	tca6416_u15: gpio@20 { /* u15 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "MIO26_PMU_INPUT_LS", "DAC_AVTT_VOUT_SEL", /* 0 - 3 */
+				  "SI5381_INT_ALM", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "FMCP_HSPC_PRSNT_M2C_B", "", "", "VCCINT_VRHOT_B", /* 10 - 13 */
+				  "", "8A34001_EXP_RST_B", "IRPS5401_ALERT_B", "INA226_PMBUS_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@75 { /* u17 */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PS_PMBUS */
+			/* PMBUS_ALERT done via pca9544 */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccint_io_bram_ps: ina226@41 { /* u57 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-io-bram-ps";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v8: ina226@42 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v8";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+			vcc1v2: ina226@43 { /* u58 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vadj_fmc: ina226@45 { /* u62 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vadj-fmc";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@46 { /* u67 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtavcc";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			mgt1v2: ina226@47 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v2";
+				reg = <0x47>;
+				shunt-resistor = <5000>; /* Not in schematics */
+			};
+			mgt1v8: ina226@48 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v8";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vccint_ams: ina226@49 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-ams";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+			dac_avtt: ina226@4a { /* u59 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avtt";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			dac_avccaux: ina226@4b { /* u124 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avccaux";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			adc_avcc: ina226@4c { /* u75 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avcc";
+				reg = <0x4c>;
+				shunt-resistor = <5000>;
+			};
+			adc_avccaux: ina226@4d { /* u71 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avccaux";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+			dac_avcc: ina226@4e { /* u77 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avcc";
+				reg = <0x4e>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* NC */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* u104 - ir35215 0x10/0x40 */
+			/* u127 - ir38164 0x1b/0x4b */
+			/* u112 - ir38164 0x13/0x43 */
+			/* u123 - ir38164 0x1c/0x4c */
+
+			irps5401_44: irps5401@44 { /* IRPS5401 - u53 */
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* i2c addr 0x14 */
+			};
+			irps5401_45: irps5401@45 { /* IRPS5401 - u55 */
+				compatible = "infineon,irps5401";
+				reg = <0x45>; /* i2c addr 0x15 */
+			};
+			/* J21 header too */
+
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* SYSMON */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
+	i2c-mux@74 {
+		compatible = "nxp,pca9548"; /* u20 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c_eeprom: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u21 */
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+		i2c_si5381: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* SI5381 - u43 */
+			/* si5381: clock-generator@68 {
+				reg = <0x68>;
+			};*/
+		};
+		i2c_si570_user_c0: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_1: clock-generator@5d { /* USER C0 SI570 - u47 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c0";
+			};
+		};
+		i2c_si570_mgt: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_2: clock-generator@5d { /* USER MGT SI570 - u48 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "si570_mgt";
+			};
+		};
+		i2c_8a34001: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* U409B - 8a34001 */
+		};
+		i2c_clk104: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* CLK104_SDA */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* RFMCP connector */
+		};
+		/* 7 NC */
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* FMCP_HSPC_IIC */
+		};
+		i2c_si570_psrefclk: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si570_3: clock-generator@5d { /* USER SI570 PSREFCLK - u130 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "si570_ps_ref_clk";
+				silabs,skip-recall;
+			};
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYSMON */
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* DDR4 SODIMM */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* SFP3 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* SFP2 */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* SFP1 */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* SFP0 */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* U11 and U12 MT25QU02GCBBE12 2Gb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	disable-wp;
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	xlnx,mio-bank = <1>;
+};
+
+&psgtr {
+	status = "okay";
+	/* hspc_dp4, hspc_dp5, usb3, hspc_dp6 */
+	clocks = <&si5381_6>;
+	clock-names = "ref2";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp-zcu670-revB.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp-zcu670-revB.dts
@@ -0,0 +1,662 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZCU670 (67DR) revB
+ *
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU670 RevB";
+	compatible = "xlnx,zynqmp-zcu670-revB", "xlnx,zynqmp-zcu670",
+		     "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0x80000000>, <0x8 0x0 0x0 0x80000000>;
+		/* Another 4GB connected to PL */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		sw1 {
+			label = "sw1";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat_led {
+			label = "heartbeat"; /* DS1 */
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	ina226-vccint {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint 0>, <&vccint 1>, <&vccint 2>, <&vccint 3>;
+	};
+	ina226-vccint-io-bram-ps {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_io_bram_ps 0>, <&vccint_io_bram_ps 1>, <&vccint_io_bram_ps 2>, <&vccint_io_bram_ps 3>;
+	};
+	ina226-vcc1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v8 0>, <&vcc1v8 1>, <&vcc1v8 2>, <&vcc1v8 3>;
+	};
+	ina226-vcc1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2 0>, <&vcc1v2 1>, <&vcc1v2 2>, <&vcc1v2 3>;
+	};
+	ina226-vadj-fmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vadj_fmc 0>, <&vadj_fmc 1>, <&vadj_fmc 2>, <&vadj_fmc 3>;
+	};
+	ina226-mgtavcc {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtavcc 0>, <&mgtavcc 1>, <&mgtavcc 2>, <&mgtavcc 3>;
+	};
+	ina226-mgt1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v2 0>, <&mgt1v2 1>, <&mgt1v2 2>, <&mgt1v2 3>;
+	};
+	ina226-mgt1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v8 0>, <&mgt1v8 1>, <&mgt1v8 2>, <&mgt1v8 3>;
+	};
+	ina226-vccint-ams {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_ams 0>, <&vccint_ams 1>, <&vccint_ams 2>, <&vccint_ams 3>;
+	};
+	ina226-dac-avtt {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avtt 0>, <&dac_avtt 1>, <&dac_avtt 2>, <&dac_avtt 3>;
+	};
+	ina226-dac-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avccaux 0>, <&dac_avccaux 1>, <&dac_avccaux 2>, <&dac_avccaux 3>;
+	};
+	ina226-adc-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avcc 0>, <&adc_avcc 1>, <&adc_avcc 2>, <&adc_avcc 3>;
+	};
+	ina226-adc-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avccaux 0>, <&adc_avccaux 1>, <&adc_avccaux 2>, <&adc_avccaux 3>;
+	};
+	ina226-dac-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
+	};
+
+	/* 48MHz reference crystal */
+	ref48: ref48M {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+
+	si5381_6: si5381_6 { /* refclk_usb3 - u43 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: ethernet-phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_LWR_CLK", "QSPI_LWR_DQ1", "QSPI_LWR_DQ2", "QSPI_LWR_DQ3", "QSPI_LWR_DQ0", /* 0 - 4 */
+		  "QSPI_LWR_CS_B", "", "QSPI_UPR_CS_B", "QSPI_UPR_DQ0", "QSPI_UPR_DQ1", /* 5 - 9 */
+		  "QSPI_UPR_DQ2", "QSPI_UPR_DQ3", "QSPI_UPR_CLK", "PS_GPIO2", "I2C0_SCL", /* 10 - 14 */
+		  "I2C0_SDA", "I2C1_SCL", "I2C1_SDA", "UART0_TXD", "UART0_RXD", /* 15 - 19 */
+		  "", "", "BUTTON", "LED", "", /* 20 - 24 */
+		  "", "PMU_INPUT", "SFP3_TX_DISABLE", "SFP2_TX_DISABLE", "SFP1_TX_DISABLE", /* 25 - 29 */
+		  "SFP0_TX_DISABLE", "", "PMU_GPO0", "PMU_GPO1", "PMU_GPO2", /* 30 - 34 */
+		  "PMU_GPO3", "PMU_GPO4", "PMU_GPO5", "PS_GPIO1", "SDIO_SEL", /* 35 - 39 */
+		  "SDIO_DIR_CMD", "SDIO_DIR_DAT0", "SDIO_DIR_DAT1", "SD_PWR_RST", "", /* 40 - 44 */
+		  "SDIO_DETECT", "SDIO_DAT0", "SDIO_DAT1", "SDIO_DAT2", "SDIO_DAT3", /* 45 - 49 */
+		  "SDIO_CMD", "SDIO_CLK", "USB_CLK", "USB_DIR", "USB_DATA2", /* 50 - 54 */
+		  "USB_NXT", "USB_DATA0", "USB_DATA1", "USB_STP", "USB_DATA3", /* 55 - 59 */
+		  "USB_DATA4", "USB_DATA5", "USB_DATA6", "USB_DATA7", "ENET_TX_CLK", /* 60 - 64 */
+		  "ENET_TX_D0", "ENET_TX_D1", "ENET_TX_D2", "ENET_TX_D3", "ENET_TX_CTRL", /* 65 - 69 */
+		  "ENET_RX_CLK", "ENET_RX_D0", "ENET_RX_D1", "ENET_RX_D2", "ENET_RX_D3", /* 70 - 74 */
+		  "ENET_RX_CTRL", "ENET_MDC", "ENET_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 - 89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+
+	tca6416_u15: gpio@20 { /* u15 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "MIO26_PMU_INPUT_LS", "DAC_AVTT_VOUT_SEL", /* 0 - 3 */
+				  "SI5381_INT_ALM", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "FMCP_HSPC_PRSNT_M2C_B", "", "", "VCCINT_VRHOT_B", /* 10 - 13 */
+				  "", "8A34001_EXP_RST_B", "IRPS5401_ALERT_B", "INA226_PMBUS_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@75 { /* u17 */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PS_PMBUS */
+			/* PMBUS_ALERT done via pca9544 */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccint_io_bram_ps: ina226@41 { /* u57 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-io-bram-ps";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v8: ina226@42 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v8";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+			vcc1v2: ina226@43 { /* u58 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vadj_fmc: ina226@45 { /* u62 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vadj-fmc";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@46 { /* u67 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtavcc";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			mgt1v2: ina226@47 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v2";
+				reg = <0x47>;
+				shunt-resistor = <5000>; /* Not in schematics */
+			};
+			mgt1v8: ina226@48 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v8";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vccint_ams: ina226@49 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-ams";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+			dac_avtt: ina226@4a { /* u59 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avtt";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			dac_avccaux: ina226@4b { /* u124 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avccaux";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			adc_avcc: ina226@4c { /* u75 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avcc";
+				reg = <0x4c>;
+				shunt-resistor = <5000>;
+			};
+			adc_avccaux: ina226@4d { /* u71 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avccaux";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+			dac_avcc: ina226@4e { /* u77 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avcc";
+				reg = <0x4e>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* NC */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* u104 - ir35215 0x10/0x40 */
+			/* u127 - ir38164 0x1b/0x4b */
+			/* u112 - ir38164 0x13/0x43 */
+			/* u123 - ir38164 0x1c/0x4c */
+
+			irps5401_44: irps5401@44 { /* IRPS5401 - u53 */
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* i2c addr 0x14 */
+			};
+			irps5401_45: irps5401@45 { /* IRPS5401 - u55 */
+				compatible = "infineon,irps5401";
+				reg = <0x45>; /* i2c addr 0x15 */
+			};
+			/* J21 header too */
+
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* SYSMON */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
+	i2c-mux@74 {
+		compatible = "nxp,pca9548"; /* u20 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c_eeprom: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u21 */
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+		i2c_si5381: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* SI5381 - u43 */
+			/* si5381: clock-generator@68 {
+				reg = <0x68>;
+			};*/
+		};
+		i2c_si570_user_c0: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_1: clock-generator@5d { /* USER C0 SI570 - u47 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c0";
+			};
+		};
+		i2c_si570_mgt: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_2: clock-generator@5d { /* USER MGT SI570 - u48 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <156250000>;
+				clock-output-names = "si570_mgt";
+			};
+		};
+		i2c_8a34001: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* U409B - 8a34001 */
+		};
+		i2c_clk104: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* CLK104_SDA */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* RFMCP connector */
+		};
+		/* 7 NC */
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* FMCP_HSPC_IIC */
+		};
+		i2c_si570_psrefclk: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si570_3: clock-generator@5d { /* USER SI570 PSREFCLK - u130 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <33333333>;
+				clock-frequency = <33333333>;
+				clock-output-names = "si570_ps_ref_clk";
+				silabs,skip-recall;
+			};
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYSMON */
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* DDR4 SODIMM */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* SFP3 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* SFP2 */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* SFP1 */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* SFP0 */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* U11 and U12 MT25QU02GCBBE12 2Gb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	disable-wp;
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	xlnx,mio-bank = <1>;
+	clk-phase-sd-hs = <120>, <60>;
+	clk-phase-uhs-sdr25 = <132>, <60>;
+	clk-phase-uhs-ddr50 = <153>, <48>;
+};
+
+&psgtr {
+	status = "okay";
+	/* hspc_dp4, hspc_dp5, usb3, hspc_dp6 */
+	clocks = <&si5381_6>;
+	clock-names = "ref2";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP
  *
- * (C) Copyright 2014 - 2019, Xilinx, Inc.
+ * (C) Copyright 2014 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  *
@@ -13,6 +13,7 @@
  */
 
 #include <dt-bindings/dma/xlnx-zynqmp-dpdma.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/power/xlnx-zynqmp-power.h>
 #include <dt-bindings/reset/xlnx-zynqmp-resets.h>
 
@@ -32,6 +33,7 @@
 			operating-points-v2 = <&cpu_opp_table>;
 			reg = <0x0>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			next-level-cache = <&L2>;
 		};
 
 		cpu1: cpu@1 {
@@ -41,6 +43,7 @@
 			reg = <0x1>;
 			operating-points-v2 = <&cpu_opp_table>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			next-level-cache = <&L2>;
 		};
 
 		cpu2: cpu@2 {
@@ -50,6 +53,7 @@
 			reg = <0x2>;
 			operating-points-v2 = <&cpu_opp_table>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			next-level-cache = <&L2>;
 		};
 
 		cpu3: cpu@3 {
@@ -59,6 +63,12 @@
 			reg = <0x3>;
 			operating-points-v2 = <&cpu_opp_table>;
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			next-level-cache = <&L2>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
 		};
 
 		idle-states {
@@ -75,7 +85,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp00 {
@@ -100,7 +110,8 @@
 		};
 	};
 
-	zynqmp_ipi: zynqmp_ipi {
+	zynqmp_ipi: zynqmp-ipi {
+		u-boot,dm-pre-reloc;
 		compatible = "xlnx,zynqmp-ipi-mailbox";
 		interrupt-parent = <&gic>;
 		interrupts = <0 35 4>;
@@ -109,7 +120,8 @@
 		#size-cells = <2>;
 		ranges;
 
-		ipi_mailbox_pmu1: mailbox@ff990400 {
+		ipi_mailbox_pmu1: mailbox@ff9905c0 {
+			u-boot,dm-pre-reloc;
 			reg = <0x0 0xff9905c0 0x0 0x20>,
 			      <0x0 0xff9905e0 0x0 0x20>,
 			      <0x0 0xff990e80 0x0 0x20>,
@@ -126,6 +138,7 @@
 	dcc: dcc {
 		compatible = "arm,dcc";
 		status = "disabled";
+		u-boot,dm-pre-reloc;
 	};
 
 	pmu {
@@ -135,6 +148,10 @@
 			     <0 144 4>,
 			     <0 145 4>,
 			     <0 146 4>;
+		interrupt-affinity = <&cpu0>,
+				     <&cpu1>,
+				     <&cpu2>,
+				     <&cpu3>;
 	};
 
 	psci {
@@ -147,8 +164,10 @@
 			compatible = "xlnx,zynqmp-firmware";
 			#power-domain-cells = <1>;
 			method = "smc";
+			u-boot,dm-pre-reloc;
 
 			zynqmp_power: zynqmp-power {
+				u-boot,dm-pre-reloc;
 				compatible = "xlnx,zynqmp-power";
 				interrupt-parent = <&gic>;
 				interrupts = <0 35 4>;
@@ -156,43 +175,84 @@
 				mbox-names = "tx", "rx";
 			};
 
-			zynqmp_clk: clock-controller {
-				#clock-cells = <1>;
-				compatible = "xlnx,zynqmp-clk";
-				clocks = <&pss_ref_clk>,
-					 <&video_clk>,
-					 <&pss_alt_ref_clk>,
-					 <&aux_ref_clk>,
-					 <&gt_crx_ref_clk>;
-				clock-names = "pss_ref_clk",
-					      "video_clk",
-					      "pss_alt_ref_clk",
-					      "aux_ref_clk",
-					      "gt_crx_ref_clk";
-			};
-
-			nvmem_firmware {
+			nvmem-firmware {
 				compatible = "xlnx,zynqmp-nvmem-fw";
 				#address-cells = <1>;
 				#size-cells = <1>;
 
-				soc_revision: soc_revision@0 {
+				soc_revision: soc-revision@0 {
 					reg = <0x0 0x4>;
 				};
+				/* efuse access */
+				efuse_dna: efuse-dna@c {
+					reg = <0xc 0xc>;
+				};
+				efuse_usr0: efuse-usr0@20 {
+					reg = <0x20 0x4>;
+				};
+				efuse_usr1: efuse-usr1@24 {
+					reg = <0x24 0x4>;
+				};
+				efuse_usr2: efuse-usr2@28 {
+					reg = <0x28 0x4>;
+				};
+				efuse_usr3: efuse-usr3@2c {
+					reg = <0x2c 0x4>;
+				};
+				efuse_usr4: efuse-usr4@30 {
+					reg = <0x30 0x4>;
+				};
+				efuse_usr5: efuse-usr5@34 {
+					reg = <0x34 0x4>;
+				};
+				efuse_usr6: efuse-usr6@38 {
+					reg = <0x38 0x4>;
+				};
+				efuse_usr7: efuse-usr7@3c {
+					reg = <0x3c 0x4>;
+				};
+				efuse_miscusr: efuse-miscusr@40 {
+					reg = <0x40 0x4>;
+				};
+				efuse_chash: efuse-chash@50 {
+					reg = <0x50 0x4>;
+				};
+				efuse_pufmisc: efuse-pufmisc@54 {
+					reg = <0x54 0x4>;
+				};
+				efuse_sec: efuse-sec@58 {
+					reg = <0x58 0x4>;
+				};
+				efuse_spkid: efuse-spkid@5c {
+					reg = <0x5c 0x4>;
+				};
+				efuse_ppk0hash: efuse-ppk0hash@a0 {
+					reg = <0xa0 0x30>;
+				};
+				efuse_ppk1hash: efuse-ppk1hash@d0 {
+					reg = <0xd0 0x30>;
+				};
 			};
 
 			zynqmp_pcap: pcap {
 				compatible = "xlnx,zynqmp-pcap-fpga";
 			};
 
-			xlnx_aes: zynqmp-aes {
-				compatible = "xlnx,zynqmp-aes";
-			};
-
 			zynqmp_reset: reset-controller {
 				compatible = "xlnx,zynqmp-reset";
 				#reset-cells = <1>;
 			};
+
+			pinctrl0: pinctrl {
+				compatible = "xlnx,zynqmp-pinctrl";
+				status = "disabled";
+			};
+
+			modepin_gpio: gpio {
+				compatible = "xlnx,zynqmp-gpio-modepin";
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
 		};
 	};
 
@@ -205,6 +265,10 @@
 			     <1 10 0xf08>;
 	};
 
+	edac {
+		compatible = "arm,cortex-a53-edac";
+	};
+
 	fpga_full: fpga-full {
 		compatible = "fpga-region";
 		fpga-mgr = <&zynqmp_pcap>;
@@ -215,6 +279,7 @@
 
 	amba: axi {
 		compatible = "simple-bus";
+		u-boot,dm-pre-reloc;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
@@ -228,6 +293,7 @@
 			interrupt-parent = <&gic>;
 			tx-fifo-depth = <0x40>;
 			rx-fifo-depth = <0x40>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_CAN0>;
 			power-domains = <&zynqmp_firmware PD_CAN_0>;
 		};
 
@@ -240,11 +306,13 @@
 			interrupt-parent = <&gic>;
 			tx-fifo-depth = <0x40>;
 			rx-fifo-depth = <0x40>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_CAN1>;
 			power-domains = <&zynqmp_firmware PD_CAN_1>;
 		};
 
 		cci: cci@fd6e0000 {
 			compatible = "arm,cci-400";
+			status = "disabled";
 			reg = <0x0 0xfd6e0000 0x0 0x9000>;
 			ranges = <0x0 0x0 0xfd6e0000 0x10000>;
 			#address-cells = <1>;
@@ -263,113 +331,112 @@
 		};
 
 		/* GDMA */
-		fpd_dma_chan1: dma@fd500000 {
+		fpd_dma_chan1: dma-controller@fd500000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd500000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 124 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14e8>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan2: dma@fd510000 {
+		fpd_dma_chan2: dma-controller@fd510000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd510000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 125 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14e9>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan3: dma@fd520000 {
+		fpd_dma_chan3: dma-controller@fd520000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd520000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 126 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ea>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan4: dma@fd530000 {
+		fpd_dma_chan4: dma-controller@fd530000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd530000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 127 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14eb>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan5: dma@fd540000 {
+		fpd_dma_chan5: dma-controller@fd540000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd540000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 128 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ec>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan6: dma@fd550000 {
+		fpd_dma_chan6: dma-controller@fd550000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd550000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 129 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ed>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan7: dma@fd560000 {
+		fpd_dma_chan7: dma-controller@fd560000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd560000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 130 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ee>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan8: dma@fd570000 {
+		fpd_dma_chan8: dma-controller@fd570000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd570000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 131 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ef>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
 		gic: interrupt-controller@f9010000 {
 			compatible = "arm,gic-400";
-			#address-cells = <0>;
 			#interrupt-cells = <3>;
 			reg = <0x0 0xf9010000 0x0 0x10000>,
 			      <0x0 0xf9020000 0x0 0x20000>,
@@ -380,111 +447,122 @@
 			interrupts = <1 9 0xf04>;
 		};
 
+		gpu: gpu@fd4b0000 {
+			status = "disabled";
+			compatible = "arm,mali-400", "arm,mali-utgard";
+			reg = <0x0 0xfd4b0000 0x0 0x10000>;
+			interrupt-parent = <&gic>;
+			interrupts = <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>;
+			interrupt-names = "IRQGP", "IRQGPMMU", "IRQPP0", "IRQPPMMU0", "IRQPP1", "IRQPPMMU1";
+			clock-names = "gpu", "gpu_pp0", "gpu_pp1";
+			power-domains = <&zynqmp_firmware PD_GPU>;
+		};
+
 		/* LPDDMA default allows only secured access. inorder to enable
 		 * These dma channels, Users should ensure that these dma
 		 * Channels are allowed for non secure access.
 		 */
-		lpd_dma_chan1: dma@ffa80000 {
+		lpd_dma_chan1: dma-controller@ffa80000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffa80000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 77 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x868>;
+			/* iommus = <&smmu 0x868>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan2: dma@ffa90000 {
+		lpd_dma_chan2: dma-controller@ffa90000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffa90000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 78 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x869>;
+			/* iommus = <&smmu 0x869>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan3: dma@ffaa0000 {
+		lpd_dma_chan3: dma-controller@ffaa0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffaa0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 79 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x86a>;
+			/* iommus = <&smmu 0x86a>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan4: dma@ffab0000 {
+		lpd_dma_chan4: dma-controller@ffab0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffab0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 80 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x86b>;
+			/* iommus = <&smmu 0x86b>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan5: dma@ffac0000 {
+		lpd_dma_chan5: dma-controller@ffac0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffac0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 81 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x86c>;
+			/* iommus = <&smmu 0x86c>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan6: dma@ffad0000 {
+		lpd_dma_chan6: dma-controller@ffad0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffad0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 82 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x86d>;
+			/* iommus = <&smmu 0x86d>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan7: dma@ffae0000 {
+		lpd_dma_chan7: dma-controller@ffae0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffae0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 83 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x86e>;
+			/* iommus = <&smmu 0x86e>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan8: dma@ffaf0000 {
+		lpd_dma_chan8: dma-controller@ffaf0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffaf0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 84 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
-			iommus = <&smmu 0x86f>;
+			/* iommus = <&smmu 0x86f>; */
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
@@ -504,7 +582,6 @@
 			interrupts = <0 14 4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x872>;
 			power-domains = <&zynqmp_firmware PD_NAND>;
 		};
@@ -515,12 +592,13 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 57 4>, <0 57 4>;
 			reg = <0x0 0xff0b0000 0x0 0x1000>;
-			clock-names = "pclk", "hclk", "tx_clk";
+			clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x874>;
 			power-domains = <&zynqmp_firmware PD_ETH_0>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM0>;
+			reset-names = "gem0_rst";
 		};
 
 		gem1: ethernet@ff0c0000 {
@@ -529,12 +607,13 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 59 4>, <0 59 4>;
 			reg = <0x0 0xff0c0000 0x0 0x1000>;
-			clock-names = "pclk", "hclk", "tx_clk";
+			clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x875>;
 			power-domains = <&zynqmp_firmware PD_ETH_1>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>;
+			reset-names = "gem1_rst";
 		};
 
 		gem2: ethernet@ff0d0000 {
@@ -543,12 +622,13 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 61 4>, <0 61 4>;
 			reg = <0x0 0xff0d0000 0x0 0x1000>;
-			clock-names = "pclk", "hclk", "tx_clk";
+			clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x876>;
 			power-domains = <&zynqmp_firmware PD_ETH_2>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM2>;
+			reset-names = "gem2_rst";
 		};
 
 		gem3: ethernet@ff0e0000 {
@@ -557,18 +637,18 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 63 4>, <0 63 4>;
 			reg = <0x0 0xff0e0000 0x0 0x1000>;
-			clock-names = "pclk", "hclk", "tx_clk";
+			clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x877>;
 			power-domains = <&zynqmp_firmware PD_ETH_3>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM3>;
+			reset-names = "gem3_rst";
 		};
 
 		gpio: gpio@ff0a0000 {
 			compatible = "xlnx,zynqmp-gpio-1.0";
 			status = "disabled";
-			#address-cells = <0>;
 			#gpio-cells = <0x2>;
 			gpio-controller;
 			interrupt-parent = <&gic>;
@@ -584,6 +664,7 @@
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 17 4>;
+			clock-frequency = <400000>;
 			reg = <0x0 0xff020000 0x0 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -595,12 +676,92 @@
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 18 4>;
+			clock-frequency = <400000>;
 			reg = <0x0 0xff030000 0x0 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			power-domains = <&zynqmp_firmware PD_I2C_1>;
 		};
 
+		ocm: memory-controller@ff960000 {
+			compatible = "xlnx,zynqmp-ocmc-1.0";
+			reg = <0x0 0xff960000 0x0 0x1000>;
+			interrupt-parent = <&gic>;
+			interrupts = <0 10 4>;
+		};
+
+		perf_monitor_ocm: perf-monitor@ffa00000 {
+			compatible = "xlnx,axi-perf-monitor";
+			reg = <0x0 0xffa00000 0x0 0x10000>;
+			interrupts = <0 25 4>;
+			interrupt-parent = <&gic>;
+			xlnx,enable-profile = <0>;
+			xlnx,enable-trace = <0>;
+			xlnx,num-monitor-slots = <1>;
+			xlnx,enable-event-count = <1>;
+			xlnx,enable-event-log = <1>;
+			xlnx,have-sampled-metric-cnt = <1>;
+			xlnx,num-of-counters = <8>;
+			xlnx,metric-count-width = <32>;
+			xlnx,metrics-sample-count-width = <32>;
+			xlnx,global-count-width = <32>;
+			xlnx,metric-count-scale = <1>;
+		};
+
+		perf_monitor_ddr: perf-monitor@fd0b0000 {
+			compatible = "xlnx,axi-perf-monitor";
+			reg = <0x0 0xfd0b0000 0x0 0x10000>;
+			interrupts = <0 123 4>;
+			interrupt-parent = <&gic>;
+			xlnx,enable-profile = <0>;
+			xlnx,enable-trace = <0>;
+			xlnx,num-monitor-slots = <6>;
+			xlnx,enable-event-count = <1>;
+			xlnx,enable-event-log = <0>;
+			xlnx,have-sampled-metric-cnt = <1>;
+			xlnx,num-of-counters = <10>;
+			xlnx,metric-count-width = <32>;
+			xlnx,metrics-sample-count-width = <32>;
+			xlnx,global-count-width = <32>;
+			xlnx,metric-count-scale = <1>;
+		};
+
+		perf_monitor_cci: perf-monitor@fd490000 {
+			compatible = "xlnx,axi-perf-monitor";
+			reg = <0x0 0xfd490000 0x0 0x10000>;
+			interrupts = <0 123 4>;
+			interrupt-parent = <&gic>;
+			xlnx,enable-profile = <0>;
+			xlnx,enable-trace = <0>;
+			xlnx,num-monitor-slots = <1>;
+			xlnx,enable-event-count = <1>;
+			xlnx,enable-event-log = <0>;
+			xlnx,have-sampled-metric-cnt = <1>;
+			xlnx,num-of-counters = <8>;
+			xlnx,metric-count-width = <32>;
+			xlnx,metrics-sample-count-width = <32>;
+			xlnx,global-count-width = <32>;
+			xlnx,metric-count-scale = <1>;
+		};
+
+		perf_monitor_lpd: perf-monitor@ffa10000 {
+			compatible = "xlnx,axi-perf-monitor";
+			reg = <0x0 0xffa10000 0x0 0x10000>;
+			interrupts = <0 25 4>;
+			interrupt-parent = <&gic>;
+			xlnx,enable-profile = <0>;
+			xlnx,enable-trace = <0>;
+			xlnx,num-monitor-slots = <1>;
+			xlnx,enable-event-count = <1>;
+			xlnx,enable-event-log = <1>;
+			xlnx,have-sampled-metric-cnt = <1>;
+			xlnx,num-of-counters = <8>;
+			xlnx,metric-count-width = <32>;
+			xlnx,metrics-sample-count-width = <32>;
+			xlnx,global-count-width = <32>;
+			xlnx,metric-count-scale = <1>;
+		};
+
 		pcie: pcie@fd0e0000 {
 			compatible = "xlnx,nwl-pcie-2.11";
 			status = "disabled";
@@ -620,7 +781,7 @@
 			msi-parent = <&pcie>;
 			reg = <0x0 0xfd0e0000 0x0 0x1000>,
 			      <0x0 0xfd480000 0x0 0x1000>,
-			      <0x80 0x00000000 0x0 0x1000000>;
+			      <0x80 0x00000000 0x0 0x10000000>;
 			reg-names = "breg", "pcireg", "cfg";
 			ranges = <0x02000000 0x00000000 0xe0000000 0x00000000 0xe0000000 0x00000000 0x10000000>,/* non-prefetchable memory */
 				 <0x43000000 0x00000006 0x00000000 0x00000006 0x00000000 0x00000002 0x00000000>;/* prefetchable memory */
@@ -630,6 +791,7 @@
 					<0x0 0x0 0x0 0x2 &pcie_intc 0x2>,
 					<0x0 0x0 0x0 0x3 &pcie_intc 0x3>,
 					<0x0 0x0 0x0 0x4 &pcie_intc 0x4>;
+			iommus = <&smmu 0x4d0>;
 			power-domains = <&zynqmp_firmware PD_PCIE>;
 			pcie_intc: legacy-interrupt-controller {
 				interrupt-controller;
@@ -639,6 +801,7 @@
 		};
 
 		qspi: spi@ff0f0000 {
+			u-boot,dm-pre-reloc;
 			compatible = "xlnx,zynqmp-qspi-1.0";
 			status = "disabled";
 			clock-names = "ref_clk", "pclk";
@@ -649,7 +812,6 @@
 			      <0x0 0xc0000000 0x0 0x8000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x873>;
 			power-domains = <&zynqmp_firmware PD_QSPI>;
 		};
@@ -670,7 +832,7 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 26 4>, <0 27 4>;
 			interrupt-names = "alarm", "sec";
-			calibration = <0x8000>;
+			calibration = <0x7FFF>;
 		};
 
 		sata: ahci@fd0c0000 {
@@ -680,37 +842,40 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 133 4>;
 			power-domains = <&zynqmp_firmware PD_SATA>;
-			#stream-id-cells = <4>;
-			iommus = <&smmu 0x4c0>, <&smmu 0x4c1>,
-				 <&smmu 0x4c2>, <&smmu 0x4c3>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
+			/* iommus = <&smmu 0x4c0>, <&smmu 0x4c1>, */
+			/*	 <&smmu 0x4c2>, <&smmu 0x4c3>; */
+			/* dma-coherent; */
 		};
 
 		sdhci0: mmc@ff160000 {
+			u-boot,dm-pre-reloc;
 			compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 48 4>;
 			reg = <0x0 0xff160000 0x0 0x1000>;
 			clock-names = "clk_xin", "clk_ahb";
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x870>;
 			#clock-cells = <1>;
 			clock-output-names = "clk_out_sd0", "clk_in_sd0";
 			power-domains = <&zynqmp_firmware PD_SD_0>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_SDIO0>;
 		};
 
 		sdhci1: mmc@ff170000 {
+			u-boot,dm-pre-reloc;
 			compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 49 4>;
 			reg = <0x0 0xff170000 0x0 0x1000>;
 			clock-names = "clk_xin", "clk_ahb";
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x871>;
 			#clock-cells = <1>;
 			clock-output-names = "clk_out_sd1", "clk_in_sd1";
 			power-domains = <&zynqmp_firmware PD_SD_1>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_SDIO1>;
 		};
 
 		smmu: iommu@fd800000 {
@@ -792,43 +957,92 @@
 		};
 
 		uart0: serial@ff000000 {
-			compatible = "cdns,uart-r1p12", "xlnx,xuartps";
+			u-boot,dm-pre-reloc;
+			compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 21 4>;
 			reg = <0x0 0xff000000 0x0 0x1000>;
 			clock-names = "uart_clk", "pclk";
 			power-domains = <&zynqmp_firmware PD_UART_0>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_UART0>;
 		};
 
 		uart1: serial@ff010000 {
-			compatible = "cdns,uart-r1p12", "xlnx,xuartps";
+			u-boot,dm-pre-reloc;
+			compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 22 4>;
 			reg = <0x0 0xff010000 0x0 0x1000>;
 			clock-names = "uart_clk", "pclk";
 			power-domains = <&zynqmp_firmware PD_UART_1>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_UART1>;
 		};
 
-		usb0: usb@fe200000 {
-			compatible = "snps,dwc3";
+		usb0: usb@ff9d0000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
 			status = "disabled";
-			interrupt-parent = <&gic>;
-			interrupts = <0 65 4>;
-			reg = <0x0 0xfe200000 0x0 0x40000>;
-			clock-names = "clk_xin", "clk_ahb";
+			compatible = "xlnx,zynqmp-dwc3";
+			reg = <0x0 0xff9d0000 0x0 0x100>;
+			clock-names = "bus_clk", "ref_clk";
 			power-domains = <&zynqmp_firmware PD_USB_0>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB0_APB>;
+			reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
+			reset-gpios = <&modepin_gpio 1 GPIO_ACTIVE_LOW>;
+			ranges;
+
+			dwc3_0: usb@fe200000 {
+				compatible = "snps,dwc3";
+				status = "disabled";
+				reg = <0x0 0xfe200000 0x0 0x40000>;
+				interrupt-parent = <&gic>;
+				interrupt-names = "dwc_usb3", "otg", "hiber";
+				interrupts = <0 65 4>, <0 69 4>, <0 75 4>;
+				iommus = <&smmu 0x860>;
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,refclk_fladj;
+				snps,enable_guctl1_resume_quirk;
+				snps,enable_guctl1_ipd_quirk;
+				snps,xhci-reset-on-resume;
+				snps,xhci-stream-quirk;
+				/* dma-coherent; */
+			};
 		};
 
-		usb1: usb@fe300000 {
-			compatible = "snps,dwc3";
+		usb1: usb@ff9e0000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
 			status = "disabled";
-			interrupt-parent = <&gic>;
-			interrupts = <0 70 4>;
-			reg = <0x0 0xfe300000 0x0 0x40000>;
-			clock-names = "clk_xin", "clk_ahb";
+			compatible = "xlnx,zynqmp-dwc3";
+			reg = <0x0 0xff9e0000 0x0 0x100>;
+			clock-names = "bus_clk", "ref_clk";
 			power-domains = <&zynqmp_firmware PD_USB_1>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB1_APB>;
+			reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
+			ranges;
+
+			dwc3_1: usb@fe300000 {
+				compatible = "snps,dwc3";
+				status = "disabled";
+				reg = <0x0 0xfe300000 0x0 0x40000>;
+				interrupt-parent = <&gic>;
+				interrupt-names = "dwc_usb3", "otg", "hiber";
+				interrupts = <0 70 4>, <0 74 4>, <0 76 4>;
+				iommus = <&smmu 0x861>;
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,refclk_fladj;
+				snps,enable_guctl1_resume_quirk;
+				snps,enable_guctl1_ipd_quirk;
+				snps,xhci-reset-on-resume;
+				snps,xhci-stream-quirk;
+				/* dma-coherent; */
+			};
 		};
 
 		watchdog0: watchdog@fd4d0000 {
@@ -837,7 +1051,8 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 113 1>;
 			reg = <0x0 0xfd4d0000 0x0 0x1000>;
-			timeout-sec = <10>;
+			timeout-sec = <60>;
+			reset-on-timeout;
 		};
 
 		lpd_watchdog: watchdog@ff150000 {
@@ -849,6 +1064,32 @@
 			timeout-sec = <10>;
 		};
 
+		xilinx_ams: ams@ffa50000 {
+			compatible = "xlnx,zynqmp-ams";
+			status = "disabled";
+			interrupt-parent = <&gic>;
+			interrupts = <0 56 4>;
+			interrupt-names = "ams-irq";
+			reg = <0x0 0xffa50000 0x0 0x800>;
+			reg-names = "ams-base";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			#io-channel-cells = <1>;
+			ranges;
+
+			ams_ps: ams_ps@ffa50800 {
+				compatible = "xlnx,zynqmp-ams-ps";
+				status = "disabled";
+				reg = <0x0 0xffa50800 0x0 0x400>;
+			};
+
+			ams_pl: ams_pl@ffa50c00 {
+				compatible = "xlnx,zynqmp-ams-pl";
+				status = "disabled";
+				reg = <0x0 0xffa50c00 0x0 0x400>;
+			};
+		};
+
 		zynqmp_dpdma: dma-controller@fd4c0000 {
 			compatible = "xlnx,zynqmp-dpdma";
 			status = "disabled";
@@ -857,21 +1098,32 @@
 			interrupt-parent = <&gic>;
 			clock-names = "axi_clk";
 			power-domains = <&zynqmp_firmware PD_DP>;
+			dma-channels = <6>;
+			iommus = <&smmu 0xce4>;
 			#dma-cells = <1>;
 		};
 
+		zynqmp_dpaud_setting: dp-aud@fd4ac000 {
+			compatible = "xlnx,zynqmp-dpaud-setting", "syscon";
+			reg = <0x0 0xfd4ac000 0x0 0x1000>;
+		};
+
 		zynqmp_dpsub: display@fd4a0000 {
+			u-boot,dm-pre-reloc;
 			compatible = "xlnx,zynqmp-dpsub-1.7";
 			status = "disabled";
 			reg = <0x0 0xfd4a0000 0x0 0x1000>,
 			      <0x0 0xfd4aa000 0x0 0x1000>,
-			      <0x0 0xfd4ab000 0x0 0x1000>,
-			      <0x0 0xfd4ac000 0x0 0x1000>;
-			reg-names = "dp", "blend", "av_buf", "aud";
+			      <0x0 0xfd4ab000 0x0 0x1000>;
+			reg-names = "dp", "blend", "av_buf";
+			xlnx,dpaud-reg = <&zynqmp_dpaud_setting>;
 			interrupts = <0 119 4>;
 			interrupt-parent = <&gic>;
+			iommus = <&smmu 0xce3>;
+
 			clock-names = "dp_apb_clk", "dp_aud_clk",
 				      "dp_vtc_pixel_clk_in";
+
 			power-domains = <&zynqmp_firmware PD_DP>;
 			resets = <&zynqmp_reset ZYNQMP_RESET_DP>;
 			dma-names = "vid0", "vid1", "vid2", "gfx0";
@@ -879,6 +1131,34 @@
 			       <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO1>,
 			       <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO2>,
 			       <&zynqmp_dpdma ZYNQMP_DPDMA_GRAPHICS>;
+
+			/* dummy node to indicate there's no child i2c device */
+			i2c-bus {
+			};
+
+			zynqmp_dp_snd_codec0: zynqmp-dp-snd-codec0 {
+				compatible = "xlnx,dp-snd-codec";
+				clock-names = "aud_clk";
+			};
+
+			zynqmp_dp_snd_pcm0: zynqmp-dp-snd-pcm0 {
+				compatible = "xlnx,dp-snd-pcm0";
+				dmas = <&zynqmp_dpdma 4>;
+				dma-names = "tx";
+			};
+
+			zynqmp_dp_snd_pcm1: zynqmp-dp-snd-pcm1 {
+				compatible = "xlnx,dp-snd-pcm1";
+				dmas = <&zynqmp_dpdma 5>;
+				dma-names = "tx";
+			};
+
+			zynqmp_dp_snd_card0: zynqmp-dp-snd-card {
+				compatible = "xlnx,dp-snd-card";
+				xlnx,dp-snd-pcm = <&zynqmp_dp_snd_pcm0>,
+						  <&zynqmp_dp_snd_pcm1>;
+				xlnx,dp-snd-codec = <&zynqmp_dp_snd_codec0>;
+			};
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/configs/defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/configs/defconfig
@@ -921,7 +921,7 @@
 CONFIG_DMA_BCM2835=y
 CONFIG_DMA_SUN6I=m
 CONFIG_FSL_EDMA=y
-CONFIG_IMX_SDMA=y
+CONFIG_IMX_SDMA=m
 CONFIG_K3_DMA=y
 CONFIG_MV_XOR=y
 CONFIG_MV_XOR_V2=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/configs/xilinx_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/configs/xilinx_defconfig
@@ -0,0 +1,483 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_ARM64_VA_BITS_48=y
+CONFIG_NR_CPUS=4
+CONFIG_KEXEC=y
+CONFIG_CRASH_DUMP=y
+CONFIG_COMPAT=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_ARM64_CRYPTO=y
+CONFIG_CRYPTO_SHA1_ARM64_CE=y
+CONFIG_CRYPTO_SHA2_ARM64_CE=y
+CONFIG_CRYPTO_SHA512_ARM64_CE=y
+CONFIG_CRYPTO_SHA3_ARM64=y
+CONFIG_CRYPTO_SM3_ARM64_CE=y
+CONFIG_CRYPTO_SM4_ARM64_CE=y
+CONFIG_CRYPTO_GHASH_ARM64_CE=y
+CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
+CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
+CONFIG_CRYPTO_CHACHA20_NEON=y
+CONFIG_CRYPTO_AES_ARM64_BS=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MEMORY_HOTPLUG=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=32768
+CONFIG_TRANSPARENT_HUGEPAGE=y
+CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y
+CONFIG_CMA=y
+# CONFIG_ZONE_DMA is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=y
+CONFIG_NF_CONNTRACK=y
+CONFIG_NF_CONNTRACK_FTP=y
+CONFIG_NF_CONNTRACK_SNMP=y
+CONFIG_NF_CONNTRACK_TFTP=y
+CONFIG_NF_CT_NETLINK=y
+CONFIG_NETFILTER_XT_MARK=y
+CONFIG_NETFILTER_XT_CONNMARK=y
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=y
+CONFIG_NETFILTER_XT_TARGET_LOG=y
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=y
+CONFIG_NETFILTER_XT_MATCH_MAC=y
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_IP_NF_IPTABLES=y
+CONFIG_IP_NF_FILTER=y
+CONFIG_IP_NF_TARGET_REJECT=y
+CONFIG_IP_NF_MANGLE=y
+CONFIG_IP6_NF_IPTABLES=y
+CONFIG_IP6_NF_FILTER=y
+CONFIG_IP6_NF_TARGET_REJECT=y
+CONFIG_IP6_NF_MANGLE=y
+CONFIG_BRIDGE_NF_EBTABLES=y
+CONFIG_BRIDGE_EBT_T_FILTER=y
+CONFIG_BRIDGE_EBT_T_NAT=y
+CONFIG_BRIDGE_EBT_MARK_T=y
+CONFIG_BRIDGE=y
+CONFIG_VLAN_8021Q=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_MQPRIO=y
+CONFIG_NET_SCH_SKBPRIO=y
+CONFIG_NET_PKTGEN=y
+CONFIG_CAN=y
+CONFIG_CAN_XILINXCAN=y
+CONFIG_BT=y
+CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=y
+CONFIG_BT_LEDS=y
+CONFIG_BT_HCIBTUSB=y
+CONFIG_BT_HCIBTSDIO=y
+CONFIG_BT_HCIUART=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_ATH3K=y
+CONFIG_BT_HCIUART_LL=y
+CONFIG_BT_HCIUART_3WIRE=y
+CONFIG_BT_HCIUART_INTEL=y
+CONFIG_BT_HCIUART_QCA=y
+CONFIG_BT_HCIBCM203X=y
+CONFIG_BT_HCIBPA10X=y
+CONFIG_BT_HCIBFUSB=y
+CONFIG_BT_HCIVHCI=y
+CONFIG_BT_MRVL=y
+CONFIG_BT_MRVL_SDIO=y
+CONFIG_BT_ATH3K=y
+CONFIG_CFG80211=y
+CONFIG_NL80211_TESTMODE=y
+CONFIG_CFG80211_CERTIFICATION_ONUS=y
+CONFIG_CFG80211_REG_CELLULAR_HINTS=y
+CONFIG_CFG80211_REG_RELAX_NO_IR=y
+CONFIG_CFG80211_WEXT=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
+CONFIG_MAC80211_MESSAGE_TRACING=y
+CONFIG_MAC80211_DEBUG_MENU=y
+CONFIG_RFKILL=y
+CONFIG_RFKILL_INPUT=y
+CONFIG_RFKILL_GPIO=y
+CONFIG_NET_9P=y
+CONFIG_PCI=y
+CONFIG_PCIE_XILINX_NWL=y
+CONFIG_PCIE_XILINX=y
+CONFIG_PCIE_XDMA_PL=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_CONNECTOR=y
+CONFIG_ZYNQMP_FIRMWARE_DEBUG=y
+CONFIG_ZYNQMP_FIRMWARE_SECURE=y
+CONFIG_MTD=y
+CONFIG_MTD_TESTS=m
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_OOPS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_ARASAN=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
+CONFIG_MTD_SPI_NOR=y
+# CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
+CONFIG_MTD_UBI=y
+CONFIG_OF_OVERLAY=y
+CONFIG_OF_CONFIGFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=65536
+CONFIG_SRAM=y
+CONFIG_XILINX_SDFEC=y
+CONFIG_XILINX_FLEX_PM=y
+CONFIG_XILINX_TRAFGEN=y
+CONFIG_XILINX_AIE=y
+CONFIG_XILINX_JESD204B=y
+CONFIG_XILINX_JESD204B_PHY=y
+CONFIG_EEPROM_AT24=y
+CONFIG_EEPROM_AT25=y
+CONFIG_TI_ST=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_AHCI_CEVA=y
+# CONFIG_ATA_SFF is not set
+CONFIG_NETDEVICES=y
+CONFIG_TUN=y
+CONFIG_MACB=y
+CONFIG_XILINX_EMACLITE=y
+CONFIG_XILINX_AXI_EMAC=y
+CONFIG_AMD_PHY=y
+CONFIG_BROADCOM_PHY=y
+CONFIG_BCM7XXX_PHY=y
+CONFIG_BCM87XX_PHY=y
+CONFIG_CICADA_PHY=y
+CONFIG_DAVICOM_PHY=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_LXT_PHY=y
+CONFIG_LSI_ET1011C_PHY=y
+CONFIG_MARVELL_PHY=y
+CONFIG_MICREL_PHY=y
+CONFIG_MICROSEMI_PHY=y
+CONFIG_NATIONAL_PHY=y
+CONFIG_AT803X_PHY=y
+CONFIG_QSEMI_PHY=y
+CONFIG_REALTEK_PHY=y
+CONFIG_SMSC_PHY=y
+CONFIG_STE10XP=y
+CONFIG_DP83848_PHY=y
+CONFIG_DP83867_PHY=y
+CONFIG_VITESSE_PHY=y
+CONFIG_XILINX_PHY=y
+CONFIG_XILINX_GMII2RGMII=y
+CONFIG_USB_USBNET=y
+CONFIG_WL18XX=y
+CONFIG_WLCORE_SPI=y
+CONFIG_WLCORE_SDIO=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_GPIO_POLLED=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_MAX310X=y
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+CONFIG_SERIAL_DEV_BUS=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_TCG_TPM=y
+CONFIG_TCG_TIS_SPI=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA9541=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_CADENCE=y
+CONFIG_I2C_XILINX=y
+CONFIG_I2C_SLAVE=y
+CONFIG_I2C_SLAVE_EEPROM=y
+CONFIG_SPI=y
+CONFIG_SPI_CADENCE=y
+CONFIG_SPI_CADENCE_QUADSPI=y
+CONFIG_SPI_XILINX=y
+CONFIG_SPI_ZYNQMP_GQSPI=y
+CONFIG_PINCTRL=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+CONFIG_GPIO_ZYNQ=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_SLG7XL45106=y
+CONFIG_GPIO_TPS65086=y
+CONFIG_POWER_RESET_LTC2952=y
+CONFIG_SENSORS_IIO_HWMON=y
+CONFIG_SENSORS_LM63=y
+CONFIG_PMBUS=y
+CONFIG_SENSORS_IR38064=y
+CONFIG_SENSORS_IRPS5401=y
+CONFIG_SENSORS_MAX20751=y
+CONFIG_SENSORS_PWM_FAN=y
+CONFIG_WATCHDOG=y
+CONFIG_XILINX_WATCHDOG=y
+CONFIG_CADENCE_WATCHDOG=y
+CONFIG_MFD_TPS65086=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_REGULATOR_TPS65086=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_USB_SUPPORT=y
+CONFIG_USB_VIDEO_CLASS=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_XILINX=y
+CONFIG_VIDEO_XILINX_CSI2RXSS=y
+CONFIG_VIDEO_XILINX_AXI4S_SWITCH=y
+CONFIG_VIDEO_XILINX_CFA=y
+CONFIG_VIDEO_XILINX_CRESAMPLE=y
+CONFIG_VIDEO_XILINX_DEMOSAIC=y
+CONFIG_VIDEO_XILINX_GAMMA=y
+CONFIG_VIDEO_XILINX_HDMI21RXSS=y
+CONFIG_VIDEO_XILINX_HLS=y
+CONFIG_VIDEO_XILINX_REMAPPER=y
+CONFIG_VIDEO_XILINX_RGB2YUV=y
+CONFIG_VIDEO_XILINX_SCALER=y
+CONFIG_VIDEO_XILINX_MULTISCALER=y
+CONFIG_VIDEO_XILINX_SDIRXSS=y
+CONFIG_VIDEO_XILINX_SWITCH=y
+CONFIG_VIDEO_XILINX_TPG=y
+CONFIG_VIDEO_XILINX_VPSS_CSC=y
+CONFIG_VIDEO_XILINX_VPSS_SCALER=y
+CONFIG_VIDEO_XILINX_DPRXSS=y
+CONFIG_VIDEO_XILINX_SCD=y
+CONFIG_VIDEO_XILINX_M2M=y
+CONFIG_VIDEO_XILINX_AXI4S_BROADCASTER=y
+CONFIG_VIDEO_XILINX_AXI4S_SUBSETCONV=y
+CONFIG_VIDEO_AP1302=y
+CONFIG_VIDEO_IMX219=y
+CONFIG_VIDEO_IMX274=y
+# CONFIG_VGA_ARB is not set
+CONFIG_DRM=y
+CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM=y
+CONFIG_DRM_ZYNQMP_DPSUB=y
+CONFIG_DRM_XLNX=y
+CONFIG_DRM_XLNX_BRIDGE=y
+CONFIG_DRM_XLNX_BRIDGE_DEBUG_FS=y
+CONFIG_DRM_XLNX_DPTX=y
+CONFIG_DRM_XLNX_DSI=y
+CONFIG_DRM_XLNX_MIXER=y
+CONFIG_DRM_XLNX_PL_DISP=y
+CONFIG_DRM_XLNX_SDI=y
+CONFIG_DRM_XLNX_BRIDGE_CSC=y
+CONFIG_DRM_XLNX_BRIDGE_SCALER=y
+CONFIG_DRM_XLNX_BRIDGE_VTC=y
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_PCI is not set
+CONFIG_SND_USB_AUDIO=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_XILINX_DP=y
+CONFIG_SND_SOC_XILINX_SDI=y
+CONFIG_SND_SOC_XILINX_I2S=y
+CONFIG_SND_SOC_XILINX_AUDIO_FORMATTER=y
+CONFIG_SND_SOC_XILINX_SPDIF=y
+CONFIG_SND_SOC_XILINX_PL_SND_CARD=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_OTG=y
+CONFIG_USB_OTG_FSM=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_UAS=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_USB2244=m
+CONFIG_USB_USB5744=m
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_XILINX=y
+CONFIG_USB_CONFIGFS=y
+CONFIG_USB_CONFIGFS_ACM=y
+CONFIG_USB_CONFIGFS_ECM=y
+CONFIG_USB_CONFIGFS_ECM_SUBSET=y
+CONFIG_USB_CONFIGFS_RNDIS=y
+CONFIG_USB_CONFIGFS_EEM=y
+CONFIG_USB_CONFIGFS_MASS_STORAGE=y
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_EEM=y
+CONFIG_USB_MASS_STORAGE=m
+CONFIG_USB_G_SERIAL=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ARASAN=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_LEDS_TRIGGER_TRANSIENT=y
+CONFIG_LEDS_TRIGGER_CAMERA=y
+CONFIG_EDAC=y
+CONFIG_EDAC_SYNOPSYS=y
+CONFIG_EDAC_ZYNQMP_OCM=y
+CONFIG_EDAC_XILINX_DDR=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_ZYNQMP=y
+CONFIG_XILINX_DMA=y
+CONFIG_XILINX_ZYNQMP_DMA=y
+CONFIG_DMATEST=y
+CONFIG_DMABUF_HEAPS=y
+CONFIG_DMABUF_HEAPS_SYSTEM=y
+CONFIG_DMABUF_HEAPS_CMA=y
+CONFIG_UIO_XILINX_APM=y
+CONFIG_UIO_XILINX_AI_ENGINE=m
+CONFIG_STAGING=y
+CONFIG_XILINX_APF=y
+CONFIG_XILINX_DMA_APF=y
+CONFIG_XILINX_FCLK=y
+CONFIG_XLNX_SYNC=y
+CONFIG_SERIAL_UARTLITE_RS485=y
+CONFIG_AXIENET_HAS_TADMA=y
+CONFIG_XILINX_TSN=y
+CONFIG_COMMON_CLK_SI5341=y
+CONFIG_COMMON_CLK_SI570=y
+CONFIG_COMMON_CLK_SI5324=y
+CONFIG_COMMON_CLK_IDT8T49N24X=y
+CONFIG_COMMON_CLK_VC7=y
+CONFIG_COMMON_CLK_XLNX_CLKWZRD=y
+CONFIG_XILINX_VCU=m
+# CONFIG_ARM_ARCH_TIMER_EVTSTREAM is not set
+# CONFIG_FSL_ERRATUM_A008585 is not set
+CONFIG_REMOTEPROC=y
+CONFIG_ZYNQMP_R5_REMOTEPROC=m
+CONFIG_RPMSG_CHAR=m
+CONFIG_IIO=y
+CONFIG_INA2XX_ADC=y
+CONFIG_INA260_ADC=y
+CONFIG_XILINX_XADC=y
+CONFIG_XILINX_AMS=y
+CONFIG_VERSAL_SYSMON=y
+CONFIG_BME680=y
+CONFIG_BMG160=y
+CONFIG_BMC150_MAGN_SPI=y
+CONFIG_PWM=y
+CONFIG_PWM_CADENCE=y
+CONFIG_XILINX_INTC=y
+CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_ARM_CCI_PMU=y
+CONFIG_RAS=y
+CONFIG_ANDROID=y
+CONFIG_NVMEM_ZYNQMP=y
+CONFIG_XLNX_SEC_CFG=y
+CONFIG_FPGA=y
+CONFIG_XILINX_AFI_FPGA=y
+CONFIG_XILINX_PR_DECOUPLER=y
+CONFIG_FPGA_REGION=y
+CONFIG_OF_FPGA_REGION=y
+CONFIG_FPGA_MGR_ZYNQMP_FPGA=y
+CONFIG_FPGA_MGR_VERSAL_FPGA=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_BTRFS_FS=y
+CONFIG_EXPORTFS_BLOCK_OPS=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_HUGETLBFS=y
+CONFIG_ECRYPT_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_UBIFS_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_CRYPTO_MANAGER_DISABLE_TESTS is not set
+CONFIG_CRYPTO_CRCT10DIF=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+CONFIG_CRYPTO_DEV_XILINX_RSA=y
+CONFIG_CRYPTO_DEV_ZYNQMP_AES_SKCIPHER=y
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=256
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+# CONFIG_STRICT_DEVMEM is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/configs/xilinx_versal_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/configs/xilinx_versal_defconfig
@@ -0,0 +1,247 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_ARM64_VA_BITS_48=y
+CONFIG_NR_CPUS=2
+CONFIG_COMPAT=y
+# CONFIG_EFI is not set
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_COMPACTION is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=32768
+CONFIG_CMA=y
+# CONFIG_ZONE_DMA is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=y
+CONFIG_NF_CONNTRACK=y
+CONFIG_NF_CONNTRACK_FTP=y
+CONFIG_NF_CONNTRACK_SNMP=y
+CONFIG_NF_CONNTRACK_TFTP=y
+CONFIG_NF_CT_NETLINK=y
+CONFIG_NETFILTER_XTABLES=y
+CONFIG_NETFILTER_XT_MARK=y
+CONFIG_NETFILTER_XT_CONNMARK=y
+CONFIG_BRIDGE_NF_EBTABLES=y
+CONFIG_BRIDGE_EBT_T_FILTER=y
+CONFIG_BRIDGE_EBT_T_NAT=y
+CONFIG_BRIDGE_EBT_MARK_T=y
+CONFIG_BRIDGE=y
+CONFIG_NET_PKTGEN=y
+CONFIG_CAN=y
+CONFIG_CAN_XILINXCAN=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_ZYNQMP_FIRMWARE_DEBUG=y
+CONFIG_MTD=y
+CONFIG_MTD_TESTS=m
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_OOPS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_SPI_NOR=y
+# CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
+CONFIG_MTD_UBI=y
+CONFIG_OF_OVERLAY=y
+CONFIG_OF_CONFIGFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=65536
+CONFIG_SRAM=y
+CONFIG_XILINX_AIE=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+CONFIG_TUN=y
+CONFIG_MACB=y
+CONFIG_MARVELL_PHY=y
+CONFIG_MICROSEMI_PHY=y
+CONFIG_REALTEK_PHY=y
+CONFIG_DP83848_PHY=y
+CONFIG_DP83867_PHY=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_GPIO_POLLED=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_CADENCE=y
+CONFIG_SPI=y
+CONFIG_SPI_CADENCE=y
+CONFIG_SPI_CADENCE_QUADSPI=y
+CONFIG_SPI_XILINX=y
+CONFIG_SPI_ZYNQMP_GQSPI=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_ZYNQ=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_XILINX_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_XILINX=y
+CONFIG_VIDEO_XILINX_CSI2RXSS=y
+CONFIG_VIDEO_XILINX_AXI4S_SWITCH=y
+CONFIG_VIDEO_XILINX_CFA=y
+CONFIG_VIDEO_XILINX_CRESAMPLE=y
+CONFIG_VIDEO_XILINX_DEMOSAIC=y
+CONFIG_VIDEO_XILINX_GAMMA=y
+CONFIG_VIDEO_XILINX_HLS=y
+CONFIG_VIDEO_XILINX_REMAPPER=y
+CONFIG_VIDEO_XILINX_RGB2YUV=y
+CONFIG_VIDEO_XILINX_SCALER=y
+CONFIG_VIDEO_XILINX_MULTISCALER=y
+CONFIG_VIDEO_XILINX_SDIRXSS=y
+CONFIG_VIDEO_XILINX_SWITCH=y
+CONFIG_VIDEO_XILINX_TPG=y
+CONFIG_VIDEO_XILINX_VPSS_CSC=y
+CONFIG_VIDEO_XILINX_VPSS_SCALER=y
+CONFIG_VIDEO_XILINX_SCD=y
+CONFIG_VIDEO_XILINX_M2M=y
+CONFIG_DRM=y
+CONFIG_DRM_XLNX=y
+CONFIG_DRM_XLNX_BRIDGE=y
+CONFIG_DRM_XLNX_BRIDGE_DEBUG_FS=y
+CONFIG_DRM_XLNX_DSI=y
+CONFIG_DRM_XLNX_MIXER=y
+CONFIG_DRM_XLNX_PL_DISP=y
+CONFIG_DRM_XLNX_SDI=y
+CONFIG_DRM_XLNX_BRIDGE_CSC=y
+CONFIG_DRM_XLNX_BRIDGE_SCALER=y
+CONFIG_DRM_XLNX_BRIDGE_VTC=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_OTG=y
+CONFIG_USB_OTG_FSM=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_CONFIGFS=y
+CONFIG_USB_CONFIGFS_ACM=y
+CONFIG_USB_CONFIGFS_ECM=y
+CONFIG_USB_CONFIGFS_ECM_SUBSET=y
+CONFIG_USB_CONFIGFS_RNDIS=y
+CONFIG_USB_CONFIGFS_EEM=y
+CONFIG_USB_CONFIGFS_MASS_STORAGE=y
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_EEM=y
+CONFIG_USB_MASS_STORAGE=m
+CONFIG_USB_G_SERIAL=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ARASAN=y
+CONFIG_EDAC=y
+CONFIG_EDAC_XILINX_DDR=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_ZYNQMP=y
+CONFIG_DMADEVICES=y
+CONFIG_XILINX_ZYNQMP_DMA=y
+CONFIG_DMATEST=y
+CONFIG_DMABUF_HEAPS=y
+CONFIG_DMABUF_HEAPS_SYSTEM=y
+CONFIG_DMABUF_HEAPS_CMA=y
+CONFIG_UIO=y
+CONFIG_UIO_PDRV_GENIRQ=m
+CONFIG_UIO_DMEM_GENIRQ=m
+CONFIG_STAGING=y
+# CONFIG_ARM_ARCH_TIMER_EVTSTREAM is not set
+# CONFIG_FSL_ERRATUM_A008585 is not set
+CONFIG_REMOTEPROC=y
+CONFIG_ZYNQMP_R5_REMOTEPROC=m
+CONFIG_RPMSG_CHAR=m
+CONFIG_IIO=y
+CONFIG_VERSAL_SYSMON=y
+CONFIG_XILINX_INTC=y
+CONFIG_ARM_CCI_PMU=y
+CONFIG_RAS=y
+CONFIG_ANDROID=y
+CONFIG_XLNX_SEC_CFG=y
+CONFIG_FPGA=y
+CONFIG_XILINX_PR_DECOUPLER=y
+CONFIG_FPGA_REGION=y
+CONFIG_OF_FPGA_REGION=y
+CONFIG_FPGA_MGR_VERSAL_FPGA=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_BTRFS_FS=y
+CONFIG_EXPORTFS_BLOCK_OPS=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_ECRYPT_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_UBIFS_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=256
+CONFIG_PRINTK_TIME=y
+# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+# CONFIG_STRICT_DEVMEM is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/configs/xilinx_zynqmp_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/configs/xilinx_zynqmp_defconfig
@@ -0,0 +1,431 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CGROUPS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_NR_CPUS=4
+CONFIG_COMPAT=y
+# CONFIG_DMI is not set
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MEMORY_HOTPLUG=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=32768
+CONFIG_TRANSPARENT_HUGEPAGE=y
+CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y
+CONFIG_CMA=y
+# CONFIG_ZONE_DMA is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_XT_MARK=y
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=y
+CONFIG_NETFILTER_XT_TARGET_LOG=y
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=y
+CONFIG_NETFILTER_XT_MATCH_MAC=y
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_IP_NF_IPTABLES=y
+CONFIG_IP_NF_FILTER=y
+CONFIG_IP_NF_TARGET_REJECT=y
+CONFIG_IP_NF_MANGLE=y
+CONFIG_IP6_NF_IPTABLES=y
+CONFIG_IP6_NF_FILTER=y
+CONFIG_IP6_NF_TARGET_REJECT=y
+CONFIG_IP6_NF_MANGLE=y
+CONFIG_BRIDGE_NF_EBTABLES=y
+CONFIG_BRIDGE_EBT_T_FILTER=y
+CONFIG_BRIDGE_EBT_T_NAT=y
+CONFIG_BRIDGE_EBT_MARK_T=y
+CONFIG_BRIDGE=y
+CONFIG_VLAN_8021Q=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_MQPRIO=y
+CONFIG_NET_SCH_SKBPRIO=y
+CONFIG_NET_PKTGEN=y
+CONFIG_CAN=y
+CONFIG_CAN_XILINXCAN=y
+CONFIG_BT=y
+CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=y
+CONFIG_BT_LEDS=y
+CONFIG_BT_HCIBTUSB=y
+CONFIG_BT_HCIBTSDIO=y
+CONFIG_BT_HCIUART=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_ATH3K=y
+CONFIG_BT_HCIUART_LL=y
+CONFIG_BT_HCIUART_3WIRE=y
+CONFIG_BT_HCIUART_INTEL=y
+CONFIG_BT_HCIUART_QCA=y
+CONFIG_BT_HCIBCM203X=y
+CONFIG_BT_HCIBPA10X=y
+CONFIG_BT_HCIBFUSB=y
+CONFIG_BT_HCIVHCI=y
+CONFIG_BT_MRVL=y
+CONFIG_BT_MRVL_SDIO=y
+CONFIG_BT_ATH3K=y
+CONFIG_CFG80211=y
+CONFIG_NL80211_TESTMODE=y
+CONFIG_CFG80211_CERTIFICATION_ONUS=y
+CONFIG_CFG80211_REG_CELLULAR_HINTS=y
+CONFIG_CFG80211_REG_RELAX_NO_IR=y
+CONFIG_CFG80211_WEXT=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
+CONFIG_MAC80211_MESSAGE_TRACING=y
+CONFIG_MAC80211_DEBUG_MENU=y
+CONFIG_RFKILL=y
+CONFIG_RFKILL_INPUT=y
+CONFIG_RFKILL_GPIO=y
+CONFIG_NET_9P=y
+CONFIG_PCI=y
+CONFIG_PCIE_XILINX_NWL=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_CONNECTOR=y
+CONFIG_ZYNQMP_FIRMWARE_DEBUG=y
+CONFIG_ZYNQMP_FIRMWARE_SECURE=y
+CONFIG_MTD=y
+CONFIG_MTD_TESTS=m
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_OOPS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_ARASAN=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
+CONFIG_MTD_SPI_NOR=y
+# CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
+CONFIG_MTD_UBI=y
+CONFIG_OF_OVERLAY=y
+CONFIG_OF_CONFIGFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=65536
+CONFIG_XILINX_SDFEC=y
+CONFIG_XILINX_JESD204B=y
+CONFIG_XILINX_JESD204B_PHY=y
+CONFIG_EEPROM_AT24=y
+CONFIG_EEPROM_AT25=y
+CONFIG_TI_ST=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_AHCI_CEVA=y
+# CONFIG_ATA_SFF is not set
+CONFIG_NETDEVICES=y
+CONFIG_TUN=y
+CONFIG_MACB=y
+CONFIG_XILINX_EMACLITE=y
+CONFIG_XILINX_AXI_EMAC=y
+CONFIG_AMD_PHY=y
+CONFIG_BROADCOM_PHY=y
+CONFIG_BCM7XXX_PHY=y
+CONFIG_BCM87XX_PHY=y
+CONFIG_CICADA_PHY=y
+CONFIG_DAVICOM_PHY=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_LXT_PHY=y
+CONFIG_LSI_ET1011C_PHY=y
+CONFIG_MARVELL_PHY=y
+CONFIG_MICREL_PHY=y
+CONFIG_NATIONAL_PHY=y
+CONFIG_AT803X_PHY=y
+CONFIG_QSEMI_PHY=y
+CONFIG_REALTEK_PHY=y
+CONFIG_SMSC_PHY=y
+CONFIG_STE10XP=y
+CONFIG_DP83867_PHY=y
+CONFIG_VITESSE_PHY=y
+CONFIG_XILINX_GMII2RGMII=y
+CONFIG_USB_USBNET=y
+CONFIG_WL18XX=y
+CONFIG_WLCORE_SPI=y
+CONFIG_WLCORE_SDIO=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_GPIO_POLLED=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_MAX310X=y
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+CONFIG_SERIAL_DEV_BUS=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_TCG_TPM=y
+CONFIG_TCG_TIS_SPI=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_CADENCE=y
+CONFIG_I2C_XILINX=y
+CONFIG_I2C_SLAVE=y
+CONFIG_I2C_SLAVE_EEPROM=y
+CONFIG_SPI=y
+CONFIG_SPI_CADENCE=y
+CONFIG_SPI_XILINX=y
+CONFIG_SPI_ZYNQMP_GQSPI=y
+CONFIG_PINCTRL=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+CONFIG_GPIO_ZYNQ=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_SLG7XL45106=y
+CONFIG_GPIO_TPS65086=y
+CONFIG_POWER_RESET_LTC2952=y
+CONFIG_SENSORS_IIO_HWMON=y
+CONFIG_SENSORS_LM63=y
+CONFIG_PMBUS=y
+CONFIG_SENSORS_IRPS5401=y
+CONFIG_SENSORS_MAX20751=y
+CONFIG_SENSORS_PWM_FAN=y
+CONFIG_WATCHDOG=y
+CONFIG_XILINX_WATCHDOG=y
+CONFIG_CADENCE_WATCHDOG=y
+CONFIG_MFD_TPS65086=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_REGULATOR_TPS65086=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_USB_SUPPORT=y
+CONFIG_USB_VIDEO_CLASS=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_XILINX=y
+CONFIG_VIDEO_XILINX_CSI2RXSS=y
+CONFIG_VIDEO_XILINX_AXI4S_SWITCH=y
+CONFIG_VIDEO_XILINX_CFA=y
+CONFIG_VIDEO_XILINX_CRESAMPLE=y
+CONFIG_VIDEO_XILINX_DEMOSAIC=y
+CONFIG_VIDEO_XILINX_GAMMA=y
+CONFIG_VIDEO_XILINX_HDMI21RXSS=y
+CONFIG_VIDEO_XILINX_HLS=y
+CONFIG_VIDEO_XILINX_REMAPPER=y
+CONFIG_VIDEO_XILINX_RGB2YUV=y
+CONFIG_VIDEO_XILINX_SCALER=y
+CONFIG_VIDEO_XILINX_MULTISCALER=y
+CONFIG_VIDEO_XILINX_SDIRXSS=y
+CONFIG_VIDEO_XILINX_SWITCH=y
+CONFIG_VIDEO_XILINX_TPG=y
+CONFIG_VIDEO_XILINX_VPSS_CSC=y
+CONFIG_VIDEO_XILINX_VPSS_SCALER=y
+CONFIG_VIDEO_XILINX_SCD=y
+CONFIG_VIDEO_XILINX_M2M=y
+CONFIG_VIDEO_XILINX_AXI4S_BROADCASTER=y
+CONFIG_VIDEO_XILINX_AXI4S_SUBSETCONV=y
+CONFIG_VIDEO_AP1302=y
+CONFIG_VIDEO_AR1335=y
+CONFIG_VIDEO_IMX219=y
+CONFIG_VIDEO_IMX274=y
+# CONFIG_VGA_ARB is not set
+CONFIG_DRM=y
+CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM=y
+CONFIG_DRM_ZYNQMP_DPSUB=y
+CONFIG_DRM_XLNX=y
+CONFIG_DRM_XLNX_BRIDGE=y
+CONFIG_DRM_XLNX_BRIDGE_DEBUG_FS=y
+CONFIG_DRM_XLNX_DSI=y
+CONFIG_DRM_XLNX_MIXER=y
+CONFIG_DRM_XLNX_PL_DISP=y
+CONFIG_DRM_XLNX_SDI=y
+CONFIG_DRM_XLNX_BRIDGE_CSC=y
+CONFIG_DRM_XLNX_BRIDGE_SCALER=y
+CONFIG_DRM_XLNX_BRIDGE_VTC=y
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_PCI is not set
+CONFIG_SND_USB_AUDIO=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_XILINX_DP=y
+CONFIG_SND_SOC_XILINX_SDI=y
+CONFIG_SND_SOC_XILINX_I2S=y
+CONFIG_SND_SOC_XILINX_AUDIO_FORMATTER=y
+CONFIG_SND_SOC_XILINX_SPDIF=y
+CONFIG_SND_SOC_XILINX_PL_SND_CARD=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_OTG=y
+CONFIG_USB_OTG_FSM=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_UAS=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_USB2244=m
+CONFIG_USB_USB5744=m
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_XILINX=y
+CONFIG_USB_CONFIGFS=y
+CONFIG_USB_CONFIGFS_ACM=y
+CONFIG_USB_CONFIGFS_ECM=y
+CONFIG_USB_CONFIGFS_ECM_SUBSET=y
+CONFIG_USB_CONFIGFS_RNDIS=y
+CONFIG_USB_CONFIGFS_EEM=y
+CONFIG_USB_CONFIGFS_MASS_STORAGE=y
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_EEM=y
+CONFIG_USB_MASS_STORAGE=m
+CONFIG_USB_G_SERIAL=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ARASAN=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_LEDS_TRIGGER_TRANSIENT=y
+CONFIG_LEDS_TRIGGER_CAMERA=y
+CONFIG_EDAC=y
+CONFIG_EDAC_SYNOPSYS=y
+CONFIG_EDAC_ZYNQMP_OCM=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_ZYNQMP=y
+CONFIG_DMADEVICES=y
+CONFIG_XILINX_DMA=y
+CONFIG_XILINX_ZYNQMP_DMA=y
+CONFIG_DMATEST=y
+CONFIG_DMABUF_HEAPS=y
+CONFIG_DMABUF_HEAPS_SYSTEM=y
+CONFIG_DMABUF_HEAPS_CMA=y
+CONFIG_UIO=y
+CONFIG_UIO_PDRV_GENIRQ=m
+CONFIG_UIO_DMEM_GENIRQ=m
+CONFIG_UIO_XILINX_APM=y
+CONFIG_STAGING=y
+CONFIG_XILINX_FCLK=y
+CONFIG_XLNX_SYNC=y
+CONFIG_SERIAL_UARTLITE_RS485=y
+CONFIG_AXIENET_HAS_TADMA=y
+CONFIG_XILINX_TSN=y
+CONFIG_COMMON_CLK_SI5341=y
+CONFIG_COMMON_CLK_SI570=y
+CONFIG_COMMON_CLK_SI5324=y
+CONFIG_COMMON_CLK_IDT8T49N24X=y
+CONFIG_COMMON_CLK_VC7=y
+CONFIG_COMMON_CLK_XLNX_CLKWZRD=y
+CONFIG_XILINX_VCU=m
+CONFIG_REMOTEPROC=y
+CONFIG_ZYNQMP_R5_REMOTEPROC=m
+CONFIG_RPMSG_CHAR=m
+CONFIG_IIO=y
+CONFIG_INA2XX_ADC=y
+CONFIG_INA260_ADC=y
+CONFIG_XILINX_XADC=y
+CONFIG_XILINX_AMS=y
+CONFIG_BME680=y
+CONFIG_BMG160=y
+CONFIG_BMC150_MAGN_SPI=y
+CONFIG_PWM=y
+CONFIG_PWM_CADENCE=y
+CONFIG_XILINX_INTC=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_ARM_CCI_PMU=y
+CONFIG_RAS=y
+CONFIG_ANDROID=y
+CONFIG_NVMEM_ZYNQMP=y
+CONFIG_FPGA=y
+CONFIG_XILINX_AFI_FPGA=y
+CONFIG_XILINX_PR_DECOUPLER=y
+CONFIG_FPGA_REGION=y
+CONFIG_OF_FPGA_REGION=y
+CONFIG_FPGA_MGR_ZYNQMP_FPGA=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_BTRFS_FS=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_HUGETLBFS=y
+CONFIG_ECRYPT_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_UBIFS_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_CRYPTO_MANAGER_DISABLE_TESTS is not set
+CONFIG_CRYPTO_CRCT10DIF=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+CONFIG_CRYPTO_DEV_XILINX_RSA=y
+CONFIG_CRYPTO_DEV_ZYNQMP_AES_SKCIPHER=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=256
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+# CONFIG_STRICT_DEVMEM is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/crypto/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/crypto/Kconfig
@@ -59,6 +59,7 @@
 	select CRYPTO_HASH
 	select CRYPTO_GF128MUL
 	select CRYPTO_LIB_AES
+	select CRYPTO_AEAD
 
 config CRYPTO_CRCT10DIF_ARM64_CE
 	tristate "CRCT10DIF digest algorithm using PMULL instructions"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/crypto/poly1305-glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/crypto/poly1305-glue.c
@@ -52,7 +52,7 @@
 {
 	if (unlikely(!dctx->sset)) {
 		if (!dctx->rset) {
-			poly1305_init_arch(dctx, src);
+			poly1305_init_arm64(&dctx->h, src);
 			src += POLY1305_BLOCK_SIZE;
 			len -= POLY1305_BLOCK_SIZE;
 			dctx->rset = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/acpi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/acpi.h
@@ -97,6 +97,18 @@
 	return	acpi_cpu_get_madt_gicc(cpu)->uid;
 }
 
+static inline int get_cpu_for_acpi_id(u32 uid)
+{
+	int cpu;
+
+	for (cpu = 0; cpu < nr_cpu_ids; cpu++)
+		if (acpi_cpu_get_madt_gicc(cpu) &&
+		    uid == get_acpi_id_for_cpu(cpu))
+			return cpu;
+
+	return -EINVAL;
+}
+
 static inline void arch_fix_phys_package_id(int num, u32 slot) { }
 void __init acpi_init_cpus(void);
 int apei_claim_sea(struct pt_regs *regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/arch_gicv3.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/arch_gicv3.h
@@ -26,12 +26,6 @@
  * sets the GP register's most significant bits to 0 with an explicit cast.
  */
 
-static inline void gic_write_eoir(u32 irq)
-{
-	write_sysreg_s(irq, SYS_ICC_EOIR1_EL1);
-	isb();
-}
-
 static __always_inline void gic_write_dir(u32 irq)
 {
 	write_sysreg_s(irq, SYS_ICC_DIR_EL1);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/arch_timer.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/arch_timer.h
@@ -32,7 +32,7 @@
 	({								\
 		const struct arch_timer_erratum_workaround *__wa;	\
 		__wa = __this_cpu_read(timer_unstable_counter_workaround); \
-		(__wa && __wa->h) ? __wa->h : arch_timer_##h;		\
+		(__wa && __wa->h) ? ({ isb(); __wa->h;}) : arch_timer_##h; \
 	})
 
 #else
@@ -52,8 +52,6 @@
 	enum arch_timer_erratum_match_type match_type;
 	const void *id;
 	const char *desc;
-	u32 (*read_cntp_tval_el0)(void);
-	u32 (*read_cntv_tval_el0)(void);
 	u64 (*read_cntpct_el0)(void);
 	u64 (*read_cntvct_el0)(void);
 	int (*set_next_event_phys)(unsigned long, struct clock_event_device *);
@@ -64,24 +62,15 @@
 DECLARE_PER_CPU(const struct arch_timer_erratum_workaround *,
 		timer_unstable_counter_workaround);
 
-/* inline sysreg accessors that make erratum_handler() work */
-static inline notrace u32 arch_timer_read_cntp_tval_el0(void)
-{
-	return read_sysreg(cntp_tval_el0);
-}
-
-static inline notrace u32 arch_timer_read_cntv_tval_el0(void)
-{
-	return read_sysreg(cntv_tval_el0);
-}
-
 static inline notrace u64 arch_timer_read_cntpct_el0(void)
 {
+	isb();
 	return read_sysreg(cntpct_el0);
 }
 
 static inline notrace u64 arch_timer_read_cntvct_el0(void)
 {
+	isb();
 	return read_sysreg(cntvct_el0);
 }
 
@@ -102,51 +91,58 @@
  * the code.
  */
 static __always_inline
-void arch_timer_reg_write_cp15(int access, enum arch_timer_reg reg, u32 val)
+void arch_timer_reg_write_cp15(int access, enum arch_timer_reg reg, u64 val)
 {
 	if (access == ARCH_TIMER_PHYS_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
 			write_sysreg(val, cntp_ctl_el0);
+			isb();
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			write_sysreg(val, cntp_tval_el0);
+		case ARCH_TIMER_REG_CVAL:
+			write_sysreg(val, cntp_cval_el0);
 			break;
+		default:
+			BUILD_BUG();
 		}
 	} else if (access == ARCH_TIMER_VIRT_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
 			write_sysreg(val, cntv_ctl_el0);
+			isb();
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			write_sysreg(val, cntv_tval_el0);
+		case ARCH_TIMER_REG_CVAL:
+			write_sysreg(val, cntv_cval_el0);
 			break;
+		default:
+			BUILD_BUG();
 		}
+	} else {
+		BUILD_BUG();
 	}
-
-	isb();
 }
 
 static __always_inline
-u32 arch_timer_reg_read_cp15(int access, enum arch_timer_reg reg)
+u64 arch_timer_reg_read_cp15(int access, enum arch_timer_reg reg)
 {
 	if (access == ARCH_TIMER_PHYS_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
 			return read_sysreg(cntp_ctl_el0);
-		case ARCH_TIMER_REG_TVAL:
-			return arch_timer_reg_read_stable(cntp_tval_el0);
+		default:
+			BUILD_BUG();
 		}
 	} else if (access == ARCH_TIMER_VIRT_ACCESS) {
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
 			return read_sysreg(cntv_ctl_el0);
-		case ARCH_TIMER_REG_TVAL:
-			return arch_timer_reg_read_stable(cntv_tval_el0);
+		default:
+			BUILD_BUG();
 		}
 	}
 
-	BUG();
+	BUILD_BUG();
+	unreachable();
 }
 
 static inline u32 arch_timer_get_cntfrq(void)
@@ -169,7 +165,6 @@
 {
 	u64 cnt;
 
-	isb();
 	cnt = arch_timer_reg_read_stable(cntpct_el0);
 	arch_counter_enforce_ordering(cnt);
 	return cnt;
@@ -189,7 +184,6 @@
 {
 	u64 cnt;
 
-	isb();
 	cnt = arch_timer_reg_read_stable(cntvct_el0);
 	arch_counter_enforce_ordering(cnt);
 	return cnt;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/asm-bug.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/asm-bug.h
@@ -14,7 +14,7 @@
 	14472:	.string file;					\
 		.popsection;					\
 								\
-		.long 14472b - 14470b;				\
+		.long 14472b - .;				\
 		.short line;
 #else
 #define _BUGVERBOSE_LOCATION(file, line)
@@ -25,9 +25,10 @@
 #define __BUG_ENTRY(flags) 				\
 		.pushsection __bug_table,"aw";		\
 		.align 2;				\
-	14470:	.long 14471f - 14470b;			\
+	14470:	.long 14471f - .;			\
 _BUGVERBOSE_LOCATION(__FILE__, __LINE__)		\
 		.short flags; 				\
+		.align 2;				\
 		.popsection;				\
 	14471:
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/assembler.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/assembler.h
@@ -108,6 +108,13 @@
 	.endm
 
 /*
+ * Clear Branch History instruction
+ */
+	.macro clearbhb
+	hint	#22
+	.endm
+
+/*
  * Speculation barrier
  */
 	.macro	sb
@@ -830,4 +837,50 @@
 
 #endif /* GNU_PROPERTY_AARCH64_FEATURE_1_DEFAULT */
 
+	.macro __mitigate_spectre_bhb_loop      tmp
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+alternative_cb  spectre_bhb_patch_loop_iter
+	mov	\tmp, #32		// Patched to correct the immediate
+alternative_cb_end
+.Lspectre_bhb_loop\@:
+	b	. + 4
+	subs	\tmp, \tmp, #1
+	b.ne	.Lspectre_bhb_loop\@
+	sb
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
+
+	.macro mitigate_spectre_bhb_loop	tmp
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+alternative_cb	spectre_bhb_patch_loop_mitigation_enable
+	b	.L_spectre_bhb_loop_done\@	// Patched to NOP
+alternative_cb_end
+	__mitigate_spectre_bhb_loop	\tmp
+.L_spectre_bhb_loop_done\@:
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
+
+	/* Save/restores x0-x3 to the stack */
+	.macro __mitigate_spectre_bhb_fw
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	stp	x0, x1, [sp, #-16]!
+	stp	x2, x3, [sp, #-16]!
+	mov	w0, #ARM_SMCCC_ARCH_WORKAROUND_3
+alternative_cb	smccc_patch_fw_mitigation_conduit
+	nop					// Patched to SMC/HVC #0
+alternative_cb_end
+	ldp	x2, x3, [sp], #16
+	ldp	x0, x1, [sp], #16
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
+
+	.macro mitigate_spectre_bhb_clear_insn
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+alternative_cb	spectre_bhb_patch_clearbhb
+	/* Patched to NOP when not supported */
+	clearbhb
+	isb
+alternative_cb_end
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
 #endif	/* __ASM_ASSEMBLER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/atomic_ll_sc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/atomic_ll_sc.h
@@ -12,19 +12,6 @@
 
 #include <linux/stringify.h>
 
-#ifdef CONFIG_ARM64_LSE_ATOMICS
-#define __LL_SC_FALLBACK(asm_ops)					\
-"	b	3f\n"							\
-"	.subsection	1\n"						\
-"3:\n"									\
-asm_ops "\n"								\
-"	b	4f\n"							\
-"	.previous\n"							\
-"4:\n"
-#else
-#define __LL_SC_FALLBACK(asm_ops) asm_ops
-#endif
-
 #ifndef CONFIG_CC_HAS_K_CONSTRAINT
 #define K
 #endif
@@ -43,12 +30,11 @@
 	int result;							\
 									\
 	asm volatile("// atomic_" #op "\n"				\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ldxr	%w0, %2\n"						\
-"	" #asm_op "	%w0, %w0, %w3\n"				\
-"	stxr	%w1, %w0, %2\n"						\
-"	cbnz	%w1, 1b\n")						\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ldxr	%w0, %2\n"					\
+	"	" #asm_op "	%w0, %w0, %w3\n"			\
+	"	stxr	%w1, %w0, %2\n"					\
+	"	cbnz	%w1, 1b\n"					\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i));				\
 }
@@ -61,13 +47,12 @@
 	int result;							\
 									\
 	asm volatile("// atomic_" #op "_return" #name "\n"		\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ld" #acq "xr	%w0, %2\n"					\
-"	" #asm_op "	%w0, %w0, %w3\n"				\
-"	st" #rel "xr	%w1, %w0, %2\n"					\
-"	cbnz	%w1, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ld" #acq "xr	%w0, %2\n"				\
+	"	" #asm_op "	%w0, %w0, %w3\n"			\
+	"	st" #rel "xr	%w1, %w0, %2\n"				\
+	"	cbnz	%w1, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -83,13 +68,12 @@
 	int val, result;						\
 									\
 	asm volatile("// atomic_fetch_" #op #name "\n"			\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %3\n"					\
-"1:	ld" #acq "xr	%w0, %3\n"					\
-"	" #asm_op "	%w1, %w0, %w4\n"				\
-"	st" #rel "xr	%w2, %w1, %3\n"					\
-"	cbnz	%w2, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %3\n"				\
+	"1:	ld" #acq "xr	%w0, %3\n"				\
+	"	" #asm_op "	%w1, %w0, %w4\n"			\
+	"	st" #rel "xr	%w2, %w1, %3\n"				\
+	"	cbnz	%w2, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (val), "=&r" (tmp), "+Q" (v->counter)	\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -142,12 +126,11 @@
 	unsigned long tmp;						\
 									\
 	asm volatile("// atomic64_" #op "\n"				\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ldxr	%0, %2\n"						\
-"	" #asm_op "	%0, %0, %3\n"					\
-"	stxr	%w1, %0, %2\n"						\
-"	cbnz	%w1, 1b")						\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ldxr	%0, %2\n"					\
+	"	" #asm_op "	%0, %0, %3\n"				\
+	"	stxr	%w1, %0, %2\n"					\
+	"	cbnz	%w1, 1b"					\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i));				\
 }
@@ -160,13 +143,12 @@
 	unsigned long tmp;						\
 									\
 	asm volatile("// atomic64_" #op "_return" #name "\n"		\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ld" #acq "xr	%0, %2\n"					\
-"	" #asm_op "	%0, %0, %3\n"					\
-"	st" #rel "xr	%w1, %0, %2\n"					\
-"	cbnz	%w1, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ld" #acq "xr	%0, %2\n"				\
+	"	" #asm_op "	%0, %0, %3\n"				\
+	"	st" #rel "xr	%w1, %0, %2\n"				\
+	"	cbnz	%w1, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -176,19 +158,18 @@
 
 #define ATOMIC64_FETCH_OP(name, mb, acq, rel, cl, op, asm_op, constraint)\
 static inline long							\
-__ll_sc_atomic64_fetch_##op##name(s64 i, atomic64_t *v)		\
+__ll_sc_atomic64_fetch_##op##name(s64 i, atomic64_t *v)			\
 {									\
 	s64 result, val;						\
 	unsigned long tmp;						\
 									\
 	asm volatile("// atomic64_fetch_" #op #name "\n"		\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %3\n"					\
-"1:	ld" #acq "xr	%0, %3\n"					\
-"	" #asm_op "	%1, %0, %4\n"					\
-"	st" #rel "xr	%w2, %1, %3\n"					\
-"	cbnz	%w2, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %3\n"				\
+	"1:	ld" #acq "xr	%0, %3\n"				\
+	"	" #asm_op "	%1, %0, %4\n"				\
+	"	st" #rel "xr	%w2, %1, %3\n"				\
+	"	cbnz	%w2, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (val), "=&r" (tmp), "+Q" (v->counter)	\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -240,15 +221,14 @@
 	unsigned long tmp;
 
 	asm volatile("// atomic64_dec_if_positive\n"
-	__LL_SC_FALLBACK(
-"	prfm	pstl1strm, %2\n"
-"1:	ldxr	%0, %2\n"
-"	subs	%0, %0, #1\n"
-"	b.lt	2f\n"
-"	stlxr	%w1, %0, %2\n"
-"	cbnz	%w1, 1b\n"
-"	dmb	ish\n"
-"2:")
+	"	prfm	pstl1strm, %2\n"
+	"1:	ldxr	%0, %2\n"
+	"	subs	%0, %0, #1\n"
+	"	b.lt	2f\n"
+	"	stlxr	%w1, %0, %2\n"
+	"	cbnz	%w1, 1b\n"
+	"	dmb	ish\n"
+	"2:"
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)
 	:
 	: "cc", "memory");
@@ -274,7 +254,6 @@
 		old = (u##sz)old;					\
 									\
 	asm volatile(							\
-	__LL_SC_FALLBACK(						\
 	"	prfm	pstl1strm, %[v]\n"				\
 	"1:	ld" #acq "xr" #sfx "\t%" #w "[oldval], %[v]\n"		\
 	"	eor	%" #w "[tmp], %" #w "[oldval], %" #w "[old]\n"	\
@@ -282,7 +261,7 @@
 	"	st" #rel "xr" #sfx "\t%w[tmp], %" #w "[new], %[v]\n"	\
 	"	cbnz	%w[tmp], 1b\n"					\
 	"	" #mb "\n"						\
-	"2:")								\
+	"2:"								\
 	: [tmp] "=&r" (tmp), [oldval] "=&r" (oldval),			\
 	  [v] "+Q" (*(u##sz *)ptr)					\
 	: [old] __stringify(constraint) "r" (old), [new] "r" (new)	\
@@ -326,7 +305,6 @@
 	unsigned long tmp, ret;						\
 									\
 	asm volatile("// __cmpxchg_double" #name "\n"			\
-	__LL_SC_FALLBACK(						\
 	"	prfm	pstl1strm, %2\n"				\
 	"1:	ldxp	%0, %1, %2\n"					\
 	"	eor	%0, %0, %3\n"					\
@@ -336,8 +314,8 @@
 	"	st" #rel "xp	%w0, %5, %6, %2\n"			\
 	"	cbnz	%w0, 1b\n"					\
 	"	" #mb "\n"						\
-	"2:")								\
-	: "=&r" (tmp), "=&r" (ret), "+Q" (*(unsigned long *)ptr)	\
+	"2:"								\
+	: "=&r" (tmp), "=&r" (ret), "+Q" (*(__uint128_t *)ptr)		\
 	: "r" (old1), "r" (old2), "r" (new1), "r" (new2)		\
 	: cl);								\
 									\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/atomic_lse.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/atomic_lse.h
@@ -11,11 +11,11 @@
 #define __ASM_ATOMIC_LSE_H
 
 #define ATOMIC_OP(op, asm_op)						\
-static inline void __lse_atomic_##op(int i, atomic_t *v)			\
+static inline void __lse_atomic_##op(int i, atomic_t *v)		\
 {									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op "	%w[i], %[v]\n"					\
+	"	" #asm_op "	%w[i], %[v]\n"				\
 	: [i] "+r" (i), [v] "+Q" (v->counter)				\
 	: "r" (v));							\
 }
@@ -32,7 +32,7 @@
 {									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op #mb "	%w[i], %w[i], %[v]"				\
+	"	" #asm_op #mb "	%w[i], %w[i], %[v]"			\
 	: [i] "+r" (i), [v] "+Q" (v->counter)				\
 	: "r" (v)							\
 	: cl);								\
@@ -130,7 +130,7 @@
 	"	add	%w[i], %w[i], %w[tmp]"				\
 	: [i] "+&r" (i), [v] "+Q" (v->counter), [tmp] "=&r" (tmp)	\
 	: "r" (v)							\
-	: cl);							\
+	: cl);								\
 									\
 	return i;							\
 }
@@ -168,7 +168,7 @@
 {									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op "	%[i], %[v]\n"					\
+	"	" #asm_op "	%[i], %[v]\n"				\
 	: [i] "+r" (i), [v] "+Q" (v->counter)				\
 	: "r" (v));							\
 }
@@ -185,7 +185,7 @@
 {									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op #mb "	%[i], %[i], %[v]"				\
+	"	" #asm_op #mb "	%[i], %[i], %[v]"			\
 	: [i] "+r" (i), [v] "+Q" (v->counter)				\
 	: "r" (v)							\
 	: cl);								\
@@ -272,7 +272,7 @@
 }
 
 #define ATOMIC64_OP_SUB_RETURN(name, mb, cl...)				\
-static inline long __lse_atomic64_sub_return##name(s64 i, atomic64_t *v)	\
+static inline long __lse_atomic64_sub_return##name(s64 i, atomic64_t *v)\
 {									\
 	unsigned long tmp;						\
 									\
@@ -403,7 +403,7 @@
 	"	eor	%[old2], %[old2], %[oldval2]\n"			\
 	"	orr	%[old1], %[old1], %[old2]"			\
 	: [old1] "+&r" (x0), [old2] "+&r" (x1),				\
-	  [v] "+Q" (*(unsigned long *)ptr)				\
+	  [v] "+Q" (*(__uint128_t *)ptr)				\
 	: [new1] "r" (x2), [new2] "r" (x3), [ptr] "r" (x4),		\
 	  [oldval1] "r" (oldval1), [oldval2] "r" (oldval2)		\
 	: cl);								\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/barrier.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/barrier.h
@@ -23,9 +23,13 @@
 #define dsb(opt)	asm volatile("dsb " #opt : : : "memory")
 
 #define psb_csync()	asm volatile("hint #17" : : : "memory")
-#define tsb_csync()	asm volatile("hint #18" : : : "memory")
+#define __tsb_csync()	asm volatile("hint #18" : : : "memory")
 #define csdb()		asm volatile("hint #20" : : : "memory")
 
+#define spec_bar()	asm volatile(ALTERNATIVE("dsb nsh\nisb\n",		\
+						 SB_BARRIER_INSN"nop\n",	\
+						 ARM64_HAS_SB))
+
 #ifdef CONFIG_ARM64_PSEUDO_NMI
 #define pmr_sync()						\
 	do {							\
@@ -46,6 +50,20 @@
 #define dma_rmb()	dmb(oshld)
 #define dma_wmb()	dmb(oshst)
 
+
+#define tsb_csync()								\
+	do {									\
+		/*								\
+		 * CPUs affected by Arm Erratum 2054223 or 2067961 needs	\
+		 * another TSB to ensure the trace is flushed. The barriers	\
+		 * don't have to be strictly back to back, as long as the	\
+		 * CPU is in trace prohibited state.				\
+		 */								\
+		if (cpus_have_final_cap(ARM64_WORKAROUND_TSB_FLUSH_FAILURE))	\
+			__tsb_csync();						\
+		__tsb_csync();							\
+	} while (0)
+
 /*
  * Generate a mask for array_index__nospec() that is ~0UL when 0 <= idx < sz
  * and 0 otherwise.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/cpu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/cpu.h
@@ -51,6 +51,7 @@
 	u64		reg_id_aa64dfr1;
 	u64		reg_id_aa64isar0;
 	u64		reg_id_aa64isar1;
+	u64		reg_id_aa64isar2;
 	u64		reg_id_aa64mmfr0;
 	u64		reg_id_aa64mmfr1;
 	u64		reg_id_aa64mmfr2;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/cpufeature.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/cpufeature.h
@@ -637,6 +637,35 @@
 	return id_aa64mmfr0_mixed_endian_el0(read_cpuid(ID_AA64MMFR0_EL1));
 }
 
+
+static inline bool supports_csv2p3(int scope)
+{
+	u64 pfr0;
+	u8 csv2_val;
+
+	if (scope == SCOPE_LOCAL_CPU)
+		pfr0 = read_sysreg_s(SYS_ID_AA64PFR0_EL1);
+	else
+		pfr0 = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1);
+
+	csv2_val = cpuid_feature_extract_unsigned_field(pfr0,
+							ID_AA64PFR0_CSV2_SHIFT);
+	return csv2_val == 3;
+}
+
+static inline bool supports_clearbhb(int scope)
+{
+	u64 isar2;
+
+	if (scope == SCOPE_LOCAL_CPU)
+		isar2 = read_sysreg_s(SYS_ID_AA64ISAR2_EL1);
+	else
+		isar2 = read_sanitised_ftr_reg(SYS_ID_AA64ISAR2_EL1);
+
+	return cpuid_feature_extract_unsigned_field(isar2,
+						    ID_AA64ISAR2_CLEARBHB_SHIFT);
+}
+
 const struct cpumask *system_32bit_el0_cpumask(void);
 DECLARE_STATIC_KEY_FALSE(arm64_mismatched_32bit_el0);
 
@@ -779,7 +808,8 @@
 		cpus_have_const_cap(ARM64_HAS_TLB_RANGE);
 }
 
-extern int do_emulate_mrs(struct pt_regs *regs, u32 sys_reg, u32 rt);
+int do_emulate_mrs(struct pt_regs *regs, u32 sys_reg, u32 rt);
+bool try_emulate_mrs(struct pt_regs *regs, u32 isn);
 
 static inline u32 id_aa64mmfr0_parange_to_phys_shift(int parange)
 {
@@ -810,7 +840,11 @@
 	if (!IS_ENABLED(CONFIG_ARM64_HW_AFDBM))
 		return false;
 
-	mmfr1 = read_cpuid(ID_AA64MMFR1_EL1);
+	/*
+	 * Use cached version to avoid emulated msr operation on KVM
+	 * guests.
+	 */
+	mmfr1 = read_sanitised_ftr_reg(SYS_ID_AA64MMFR1_EL1);
 	return cpuid_feature_extract_unsigned_field(mmfr1,
 						ID_AA64MMFR1_HADBS_SHIFT);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/cputype.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/cputype.h
@@ -41,7 +41,7 @@
 	(((midr) & MIDR_IMPLEMENTOR_MASK) >> MIDR_IMPLEMENTOR_SHIFT)
 
 #define MIDR_CPU_MODEL(imp, partnum) \
-	(((imp)			<< MIDR_IMPLEMENTOR_SHIFT) | \
+	((_AT(u32, imp)		<< MIDR_IMPLEMENTOR_SHIFT) | \
 	(0xf			<< MIDR_ARCHITECTURE_SHIFT) | \
 	((partnum)		<< MIDR_PARTNUM_SHIFT))
 
@@ -60,6 +60,8 @@
 #define ARM_CPU_IMP_FUJITSU		0x46
 #define ARM_CPU_IMP_HISI		0x48
 #define ARM_CPU_IMP_APPLE		0x61
+#define ARM_CPU_IMP_AMPERE		0xC0
+#define ARM_CPU_IMP_MICROSOFT		0x6D
 
 #define ARM_CPU_PART_AEM_V8		0xD0F
 #define ARM_CPU_PART_FOUNDATION		0xD00
@@ -73,6 +75,26 @@
 #define ARM_CPU_PART_CORTEX_A76		0xD0B
 #define ARM_CPU_PART_NEOVERSE_N1	0xD0C
 #define ARM_CPU_PART_CORTEX_A77		0xD0D
+#define ARM_CPU_PART_NEOVERSE_V1	0xD40
+#define ARM_CPU_PART_CORTEX_A78		0xD41
+#define ARM_CPU_PART_CORTEX_A78AE	0xD42
+#define ARM_CPU_PART_CORTEX_X1		0xD44
+#define ARM_CPU_PART_CORTEX_A510	0xD46
+#define ARM_CPU_PART_CORTEX_A520	0xD80
+#define ARM_CPU_PART_CORTEX_A710	0xD47
+#define ARM_CPU_PART_CORTEX_A715	0xD4D
+#define ARM_CPU_PART_CORTEX_X2		0xD48
+#define ARM_CPU_PART_NEOVERSE_N2	0xD49
+#define ARM_CPU_PART_CORTEX_A78C	0xD4B
+#define ARM_CPU_PART_CORTEX_X1C		0xD4C
+#define ARM_CPU_PART_CORTEX_X3		0xD4E
+#define ARM_CPU_PART_NEOVERSE_V2	0xD4F
+#define ARM_CPU_PART_CORTEX_A720	0xD81
+#define ARM_CPU_PART_CORTEX_X4		0xD82
+#define ARM_CPU_PART_NEOVERSE_V3	0xD84
+#define ARM_CPU_PART_CORTEX_X925	0xD85
+#define ARM_CPU_PART_CORTEX_A725	0xD87
+#define ARM_CPU_PART_NEOVERSE_N3	0xD8E
 
 #define APM_CPU_PART_POTENZA		0x000
 
@@ -103,6 +125,10 @@
 #define APPLE_CPU_PART_M1_ICESTORM	0x022
 #define APPLE_CPU_PART_M1_FIRESTORM	0x023
 
+#define AMPERE_CPU_PART_AMPERE1		0xAC3
+
+#define MICROSOFT_CPU_PART_AZURE_COBALT_100	0xD49 /* Based on r0p0 of ARM Neoverse N2 */
+
 #define MIDR_CORTEX_A53 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A53)
 #define MIDR_CORTEX_A57 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A57)
 #define MIDR_CORTEX_A72 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A72)
@@ -113,6 +139,26 @@
 #define MIDR_CORTEX_A76	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A76)
 #define MIDR_NEOVERSE_N1 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_N1)
 #define MIDR_CORTEX_A77	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A77)
+#define MIDR_NEOVERSE_V1	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_V1)
+#define MIDR_CORTEX_A78	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A78)
+#define MIDR_CORTEX_A78AE	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A78AE)
+#define MIDR_CORTEX_X1	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X1)
+#define MIDR_CORTEX_A510 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A510)
+#define MIDR_CORTEX_A520 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A520)
+#define MIDR_CORTEX_A710 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A710)
+#define MIDR_CORTEX_A715 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A715)
+#define MIDR_CORTEX_X2 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X2)
+#define MIDR_NEOVERSE_N2 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_N2)
+#define MIDR_CORTEX_A78C	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A78C)
+#define MIDR_CORTEX_X1C	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X1C)
+#define MIDR_CORTEX_X3 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X3)
+#define MIDR_NEOVERSE_V2 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_V2)
+#define MIDR_CORTEX_A720 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A720)
+#define MIDR_CORTEX_X4 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X4)
+#define MIDR_NEOVERSE_V3 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_V3)
+#define MIDR_CORTEX_X925 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X925)
+#define MIDR_CORTEX_A725 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A725)
+#define MIDR_NEOVERSE_N3 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_N3)
 #define MIDR_THUNDERX	MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX)
 #define MIDR_THUNDERX_81XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX_81XX)
 #define MIDR_THUNDERX_83XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX_83XX)
@@ -133,6 +179,8 @@
 #define MIDR_HISI_TSV110 MIDR_CPU_MODEL(ARM_CPU_IMP_HISI, HISI_CPU_PART_TSV110)
 #define MIDR_APPLE_M1_ICESTORM MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_ICESTORM)
 #define MIDR_APPLE_M1_FIRESTORM MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_FIRESTORM)
+#define MIDR_AMPERE1 MIDR_CPU_MODEL(ARM_CPU_IMP_AMPERE, AMPERE_CPU_PART_AMPERE1)
+#define MIDR_MICROSOFT_AZURE_COBALT_100 MIDR_CPU_MODEL(ARM_CPU_IMP_MICROSOFT, MICROSOFT_CPU_PART_AZURE_COBALT_100)
 
 /* Fujitsu Erratum 010001 affects A64FX 1.0 and 1.1, (v0r0 and v1r0) */
 #define MIDR_FUJITSU_ERRATUM_010001		MIDR_FUJITSU_A64FX
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/debug-monitors.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/debug-monitors.h
@@ -76,7 +76,7 @@
 
 struct step_hook {
 	struct list_head node;
-	int (*fn)(struct pt_regs *regs, unsigned int esr);
+	int (*fn)(struct pt_regs *regs, unsigned long esr);
 };
 
 void register_user_step_hook(struct step_hook *hook);
@@ -87,7 +87,7 @@
 
 struct break_hook {
 	struct list_head node;
-	int (*fn)(struct pt_regs *regs, unsigned int esr);
+	int (*fn)(struct pt_regs *regs, unsigned long esr);
 	u16 imm;
 	u16 mask; /* These bits are ignored when comparing with imm */
 };
@@ -116,6 +116,7 @@
 void kernel_enable_single_step(struct pt_regs *regs);
 void kernel_disable_single_step(void);
 int kernel_active_single_step(void);
+void kernel_rewind_single_step(struct pt_regs *regs);
 
 #ifdef CONFIG_HAVE_HW_BREAKPOINT
 int reinstall_suspended_bps(struct pt_regs *regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/efi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/efi.h
@@ -14,9 +14,16 @@
 
 #ifdef CONFIG_EFI
 extern void efi_init(void);
-extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
+
+bool efi_runtime_fixup_exception(struct pt_regs *regs, const char *msg);
 #else
 #define efi_init()
+
+static inline
+bool efi_runtime_fixup_exception(struct pt_regs *regs, const char *msg)
+{
+	return false;
+}
 #endif
 
 int efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md);
@@ -26,6 +33,7 @@
 ({									\
 	efi_virtmap_load();						\
 	__efi_fpsimd_begin();						\
+	raw_spin_lock(&efi_rt_lock);					\
 })
 
 #define arch_efi_call_virt(p, f, args...)				\
@@ -37,10 +45,12 @@
 
 #define arch_efi_call_virt_teardown()					\
 ({									\
+	raw_spin_unlock(&efi_rt_lock);					\
 	__efi_fpsimd_end();						\
 	efi_virtmap_unload();						\
 })
 
+extern raw_spinlock_t efi_rt_lock;
 efi_status_t __efi_rt_asm_wrapper(void *, const char *, ...);
 
 #define ARCH_EFI_IRQ_FLAGS_MASK (PSR_D_BIT | PSR_A_BIT | PSR_I_BIT | PSR_F_BIT)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/el2_setup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/el2_setup.h
@@ -106,7 +106,7 @@
 	msr_s	SYS_ICC_SRE_EL2, x0
 	isb					// Make sure SRE is now set
 	mrs_s	x0, SYS_ICC_SRE_EL2		// Read SRE back,
-	tbz	x0, #0, 1f			// and check that it sticks
+	tbz	x0, #0, .Lskip_gicv3_\@		// and check that it sticks
 	msr_s	SYS_ICH_HCR_EL2, xzr		// Reset ICC_HCR_EL2 to defaults
 .Lskip_gicv3_\@:
 .endm
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/esr.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/esr.h
@@ -68,6 +68,7 @@
 #define ESR_ELx_EC_MAX		(0x3F)
 
 #define ESR_ELx_EC_SHIFT	(26)
+#define ESR_ELx_EC_WIDTH	(6)
 #define ESR_ELx_EC_MASK		(UL(0x3F) << ESR_ELx_EC_SHIFT)
 #define ESR_ELx_EC(esr)		(((esr) & ESR_ELx_EC_MASK) >> ESR_ELx_EC_SHIFT)
 
@@ -323,14 +324,14 @@
 #ifndef __ASSEMBLY__
 #include <asm/types.h>
 
-static inline bool esr_is_data_abort(u32 esr)
+static inline bool esr_is_data_abort(unsigned long esr)
 {
-	const u32 ec = ESR_ELx_EC(esr);
+	const unsigned long ec = ESR_ELx_EC(esr);
 
 	return ec == ESR_ELx_EC_DABT_LOW || ec == ESR_ELx_EC_DABT_CUR;
 }
 
-const char *esr_get_class_string(u32 esr);
+const char *esr_get_class_string(unsigned long esr);
 #endif /* __ASSEMBLY */
 
 #endif /* __ASM_ESR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/exception.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/exception.h
@@ -8,20 +8,15 @@
 #define __ASM_EXCEPTION_H
 
 #include <asm/esr.h>
-#include <asm/kprobes.h>
 #include <asm/ptrace.h>
 
 #include <linux/interrupt.h>
 
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
 #define __exception_irq_entry	__irq_entry
-#else
-#define __exception_irq_entry	__kprobes
-#endif
 
-static inline u32 disr_to_esr(u64 disr)
+static inline unsigned long disr_to_esr(u64 disr)
 {
-	unsigned int esr = ESR_ELx_EC_SERROR << ESR_ELx_EC_SHIFT;
+	unsigned long esr = ESR_ELx_EC_SERROR << ESR_ELx_EC_SHIFT;
 
 	if ((disr & DISR_EL1_IDS) == 0)
 		esr |= (disr & DISR_EL1_ESR_MASK);
@@ -57,23 +52,26 @@
 				  void (*func)(struct pt_regs *));
 asmlinkage void asm_exit_to_user_mode(struct pt_regs *regs);
 
-void do_mem_abort(unsigned long far, unsigned int esr, struct pt_regs *regs);
-void do_undefinstr(struct pt_regs *regs);
-void do_bti(struct pt_regs *regs);
-void do_debug_exception(unsigned long addr_if_watchpoint, unsigned int esr,
+void do_mem_abort(unsigned long far, unsigned long esr, struct pt_regs *regs);
+void do_el0_undef(struct pt_regs *regs, unsigned long esr);
+void do_el1_undef(struct pt_regs *regs, unsigned long esr);
+void do_el0_bti(struct pt_regs *regs);
+void do_el1_bti(struct pt_regs *regs, unsigned long esr);
+void do_debug_exception(unsigned long addr_if_watchpoint, unsigned long esr,
 			struct pt_regs *regs);
-void do_fpsimd_acc(unsigned int esr, struct pt_regs *regs);
-void do_sve_acc(unsigned int esr, struct pt_regs *regs);
-void do_fpsimd_exc(unsigned int esr, struct pt_regs *regs);
-void do_sysinstr(unsigned int esr, struct pt_regs *regs);
-void do_sp_pc_abort(unsigned long addr, unsigned int esr, struct pt_regs *regs);
-void bad_el0_sync(struct pt_regs *regs, int reason, unsigned int esr);
-void do_cp15instr(unsigned int esr, struct pt_regs *regs);
+void do_fpsimd_acc(unsigned long esr, struct pt_regs *regs);
+void do_sve_acc(unsigned long esr, struct pt_regs *regs);
+void do_fpsimd_exc(unsigned long esr, struct pt_regs *regs);
+void do_el0_sys(unsigned long esr, struct pt_regs *regs);
+void do_sp_pc_abort(unsigned long addr, unsigned long esr, struct pt_regs *regs);
+void bad_el0_sync(struct pt_regs *regs, int reason, unsigned long esr);
+void do_el0_cp15(unsigned long esr, struct pt_regs *regs);
 void do_el0_svc(struct pt_regs *regs);
 void do_el0_svc_compat(struct pt_regs *regs);
-void do_ptrauth_fault(struct pt_regs *regs, unsigned int esr);
-void do_serror(struct pt_regs *regs, unsigned int esr);
+void do_el0_fpac(struct pt_regs *regs, unsigned long esr);
+void do_el1_fpac(struct pt_regs *regs, unsigned long esr);
+void do_serror(struct pt_regs *regs, unsigned long esr);
 void do_notify_resume(struct pt_regs *regs, unsigned long thread_flags);
 
-void panic_bad_stack(struct pt_regs *regs, unsigned int esr, unsigned long far);
+void panic_bad_stack(struct pt_regs *regs, unsigned long esr, unsigned long far);
 #endif	/* __ASM_EXCEPTION_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/extable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/extable.h
@@ -22,15 +22,6 @@
 
 #define ARCH_HAS_RELATIVE_EXTABLE
 
-static inline bool in_bpf_jit(struct pt_regs *regs)
-{
-	if (!IS_ENABLED(CONFIG_BPF_JIT))
-		return false;
-
-	return regs->pc >= BPF_JIT_REGION_START &&
-	       regs->pc < BPF_JIT_REGION_END;
-}
-
 #ifdef CONFIG_BPF_JIT
 int arm64_bpf_fixup_exception(const struct exception_table_entry *ex,
 			      struct pt_regs *regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/fixmap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/fixmap.h
@@ -62,9 +62,11 @@
 #endif /* CONFIG_ACPI_APEI_GHES */
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+	FIX_ENTRY_TRAMP_TEXT3,
+	FIX_ENTRY_TRAMP_TEXT2,
+	FIX_ENTRY_TRAMP_TEXT1,
 	FIX_ENTRY_TRAMP_DATA,
-	FIX_ENTRY_TRAMP_TEXT,
-#define TRAMP_VALIAS		(__fix_to_virt(FIX_ENTRY_TRAMP_TEXT))
+#define TRAMP_VALIAS		(__fix_to_virt(FIX_ENTRY_TRAMP_TEXT1))
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 	__end_of_permanent_fixed_addresses,
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/hwcap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/hwcap.h
@@ -105,6 +105,9 @@
 #define KERNEL_HWCAP_RNG		__khwcap2_feature(RNG)
 #define KERNEL_HWCAP_BTI		__khwcap2_feature(BTI)
 #define KERNEL_HWCAP_MTE		__khwcap2_feature(MTE)
+#define KERNEL_HWCAP_ECV		__khwcap2_feature(ECV)
+#define KERNEL_HWCAP_AFP		__khwcap2_feature(AFP)
+#define KERNEL_HWCAP_RPRES		__khwcap2_feature(RPRES)
 
 /*
  * This yields a mask that user programs can use to figure out what
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/insn.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/insn.h
@@ -65,6 +65,7 @@
 	AARCH64_INSN_HINT_PSB  = 0x11 << 5,
 	AARCH64_INSN_HINT_TSB  = 0x12 << 5,
 	AARCH64_INSN_HINT_CSDB = 0x14 << 5,
+	AARCH64_INSN_HINT_CLEARBHB = 0x16 << 5,
 
 	AARCH64_INSN_HINT_BTI   = 0x20 << 5,
 	AARCH64_INSN_HINT_BTIC  = 0x22 << 5,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/io.h
@@ -192,4 +192,8 @@
 extern int valid_phys_addr_range(phys_addr_t addr, size_t size);
 extern int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
 
+extern bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+					unsigned long flags);
+#define arch_memremap_can_ram_remap arch_memremap_can_ram_remap
+
 #endif	/* __ASM_IO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/irq_work.h
@@ -2,8 +2,6 @@
 #ifndef __ASM_IRQ_WORK_H
 #define __ASM_IRQ_WORK_H
 
-extern void arch_irq_work_raise(void);
-
 static inline bool arch_irq_work_has_interrupt(void)
 {
 	return true;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/kernel-pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/kernel-pgtable.h
@@ -103,8 +103,8 @@
 /*
  * Initial memory map attributes.
  */
-#define SWAPPER_PTE_FLAGS	(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
-#define SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
+#define SWAPPER_PTE_FLAGS	(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED | PTE_UXN)
+#define SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S | PMD_SECT_UXN)
 
 #if ARM64_KERNEL_USES_PMD_MAPS
 #define SWAPPER_MM_MMUFLAGS	(PMD_ATTRINDX(MT_NORMAL) | SWAPPER_PMD_FLAGS)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/kprobes.h
@@ -39,7 +39,7 @@
 int kprobe_fault_handler(struct pt_regs *regs, unsigned int fsr);
 int kprobe_exceptions_notify(struct notifier_block *self,
 			     unsigned long val, void *data);
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 void __kprobes *trampoline_probe_handler(struct pt_regs *regs);
 
 #endif /* CONFIG_KPROBES */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/kvm_arm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/kvm_arm.h
@@ -91,7 +91,7 @@
 #define HCR_HOST_VHE_FLAGS (HCR_RW | HCR_TGE | HCR_E2H)
 
 /* TCR_EL2 Registers bits */
-#define TCR_EL2_RES1		((1 << 31) | (1 << 23))
+#define TCR_EL2_RES1		((1U << 31) | (1 << 23))
 #define TCR_EL2_TBI		(1 << 20)
 #define TCR_EL2_PS_SHIFT	16
 #define TCR_EL2_PS_MASK		(7 << TCR_EL2_PS_SHIFT)
@@ -276,7 +276,7 @@
 #define CPTR_EL2_TFP_SHIFT 10
 
 /* Hyp Coprocessor Trap Register */
-#define CPTR_EL2_TCPAC	(1 << 31)
+#define CPTR_EL2_TCPAC	(1U << 31)
 #define CPTR_EL2_TAM	(1 << 30)
 #define CPTR_EL2_TTA	(1 << 20)
 #define CPTR_EL2_TFP	(1 << CPTR_EL2_TFP_SHIFT)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/kvm_emulate.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/kvm_emulate.h
@@ -366,8 +366,26 @@
 
 static inline bool kvm_is_write_fault(struct kvm_vcpu *vcpu)
 {
-	if (kvm_vcpu_abt_iss1tw(vcpu))
-		return true;
+	if (kvm_vcpu_abt_iss1tw(vcpu)) {
+		/*
+		 * Only a permission fault on a S1PTW should be
+		 * considered as a write. Otherwise, page tables baked
+		 * in a read-only memslot will result in an exception
+		 * being delivered in the guest.
+		 *
+		 * The drawback is that we end-up faulting twice if the
+		 * guest is using any of HW AF/DB: a translation fault
+		 * to map the page containing the PT (read only at
+		 * first), then a permission fault to allow the flags
+		 * to be set.
+		 */
+		switch (kvm_vcpu_trap_get_fault_type(vcpu)) {
+		case ESR_ELx_FSC_PERM:
+			return true;
+		default:
+			return false;
+		}
+	}
 
 	if (kvm_vcpu_trap_is_iabt(vcpu))
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/kvm_host.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/kvm_host.h
@@ -419,6 +419,7 @@
 #define KVM_ARM64_EXCEPT_MASK		(7 << 9) /* Target EL/MODE */
 #define KVM_ARM64_DEBUG_STATE_SAVE_SPE	(1 << 12) /* Save SPE context if active  */
 #define KVM_ARM64_DEBUG_STATE_SAVE_TRBE	(1 << 13) /* Save TRBE context if active  */
+#define KVM_ARM64_VCPU_IN_WFI		(1 << 14) /* WFI instruction trapped */
 
 #define KVM_GUESTDBG_VALID_MASK (KVM_GUESTDBG_ENABLE | \
 				 KVM_GUESTDBG_USE_SW_BP | \
@@ -711,6 +712,11 @@
 	ctxt_sys_reg(cpu_ctxt, MPIDR_EL1) = read_cpuid_mpidr();
 }
 
+static inline bool kvm_system_needs_idmapped_vectors(void)
+{
+	return cpus_have_const_cap(ARM64_SPECTRE_V3A);
+}
+
 void kvm_arm_vcpu_ptrauth_trap(struct kvm_vcpu *vcpu);
 
 static inline void kvm_arch_hardware_unsetup(void) {}
@@ -771,7 +777,6 @@
 
 #define __KVM_HAVE_ARCH_VM_ALLOC
 struct kvm *kvm_arch_alloc_vm(void);
-void kvm_arch_free_vm(struct kvm *kvm);
 
 int kvm_arm_setup_stage2(struct kvm *kvm, unsigned long type);
 
@@ -790,6 +795,10 @@
 #define kvm_vcpu_has_pmu(vcpu)					\
 	(test_bit(KVM_ARM_VCPU_PMU_V3, (vcpu)->arch.features))
 
+#define kvm_supports_32bit_el0()				\
+	(system_supports_32bit_el0() &&				\
+	 !static_branch_unlikely(&arm64_mismatched_32bit_el0))
+
 int kvm_trng_call(struct kvm_vcpu *vcpu);
 #ifdef CONFIG_KVM
 extern phys_addr_t hyp_mem_base;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/kvm_pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/kvm_pgtable.h
@@ -13,6 +13,18 @@
 
 #define KVM_PGTABLE_MAX_LEVELS		4U
 
+/*
+ * The largest supported block sizes for KVM (no 52-bit PA support):
+ *  - 4K (level 1):	1GB
+ *  - 16K (level 2):	32MB
+ *  - 64K (level 2):	512MB
+ */
+#ifdef CONFIG_ARM64_4K_PAGES
+#define KVM_PGTABLE_MIN_BLOCK_LEVEL	1U
+#else
+#define KVM_PGTABLE_MIN_BLOCK_LEVEL	2U
+#endif
+
 static inline u64 kvm_get_parange(u64 mmfr0)
 {
 	u64 parange = cpuid_feature_extract_unsigned_field(mmfr0,
@@ -58,11 +70,7 @@
 
 static inline bool kvm_level_supports_block_mapping(u32 level)
 {
-	/*
-	 * Reject invalid block mappings and don't bother with 4TB mappings for
-	 * 52-bit PAs.
-	 */
-	return !(level == 0 || (PAGE_SIZE != SZ_4K && level == 1));
+	return level >= KVM_PGTABLE_MIN_BLOCK_LEVEL;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/memory.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/memory.h
@@ -44,11 +44,8 @@
 #define _PAGE_OFFSET(va)	(-(UL(1) << (va)))
 #define PAGE_OFFSET		(_PAGE_OFFSET(VA_BITS))
 #define KIMAGE_VADDR		(MODULES_END)
-#define BPF_JIT_REGION_START	(_PAGE_END(VA_BITS_MIN))
-#define BPF_JIT_REGION_SIZE	(SZ_128M)
-#define BPF_JIT_REGION_END	(BPF_JIT_REGION_START + BPF_JIT_REGION_SIZE)
 #define MODULES_END		(MODULES_VADDR + MODULES_VSIZE)
-#define MODULES_VADDR		(BPF_JIT_REGION_END)
+#define MODULES_VADDR		(_PAGE_END(VA_BITS_MIN))
 #define MODULES_VSIZE		(SZ_128M)
 #define VMEMMAP_START		(-(UL(1) << (VA_BITS - VMEMMAP_SHIFT)))
 #define VMEMMAP_END		(VMEMMAP_START + VMEMMAP_SIZE)
@@ -353,6 +350,11 @@
 })
 
 void dump_mem_limit(void);
+
+static inline bool defer_reserve_crashkernel(void)
+{
+	return IS_ENABLED(CONFIG_ZONE_DMA) || IS_ENABLED(CONFIG_ZONE_DMA32);
+}
 #endif /* !ASSEMBLY */
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/mman.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/mman.h
@@ -3,6 +3,8 @@
 #define __ASM_MMAN_H__
 
 #include <linux/compiler.h>
+#include <linux/fs.h>
+#include <linux/shmem_fs.h>
 #include <linux/types.h>
 #include <uapi/asm/mman.h>
 
@@ -21,19 +23,24 @@
 }
 #define arch_calc_vm_prot_bits(prot, pkey) arch_calc_vm_prot_bits(prot, pkey)
 
-static inline unsigned long arch_calc_vm_flag_bits(unsigned long flags)
+static inline unsigned long arch_calc_vm_flag_bits(struct file *file,
+						   unsigned long flags)
 {
 	/*
 	 * Only allow MTE on anonymous mappings as these are guaranteed to be
 	 * backed by tags-capable memory. The vm_flags may be overridden by a
 	 * filesystem supporting MTE (RAM-based).
 	 */
-	if (system_supports_mte() && (flags & MAP_ANONYMOUS))
-		return VM_MTE_ALLOWED;
+	if (system_supports_mte()) {
+		if ((flags & MAP_ANONYMOUS) && !(flags & MAP_HUGETLB))
+			return VM_MTE_ALLOWED;
+		if (shmem_file(file))
+			return VM_MTE_ALLOWED;
+	}
 
 	return 0;
 }
-#define arch_calc_vm_flag_bits(flags) arch_calc_vm_flag_bits(flags)
+#define arch_calc_vm_flag_bits(file, flags) arch_calc_vm_flag_bits(file, flags)
 
 static inline pgprot_t arch_vm_get_page_prot(unsigned long vm_flags)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/module.lds.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/module.lds.h
@@ -1,8 +1,8 @@
 SECTIONS {
 #ifdef CONFIG_ARM64_MODULE_PLTS
-	.plt 0 (NOLOAD) : { BYTE(0) }
-	.init.plt 0 (NOLOAD) : { BYTE(0) }
-	.text.ftrace_trampoline 0 (NOLOAD) : { BYTE(0) }
+	.plt 0 : { BYTE(0) }
+	.init.plt 0 : { BYTE(0) }
+	.text.ftrace_trampoline 0 : { BYTE(0) }
 #endif
 
 #ifdef CONFIG_KASAN_SW_TAGS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/mte-kasan.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/mte-kasan.h
@@ -5,6 +5,7 @@
 #ifndef __ASM_MTE_KASAN_H
 #define __ASM_MTE_KASAN_H
 
+#include <asm/compiler.h>
 #include <asm/mte-def.h>
 
 #ifndef __ASSEMBLY__
@@ -84,10 +85,12 @@
 static inline void mte_set_mem_tag_range(void *addr, size_t size, u8 tag,
 					 bool init)
 {
-	u64 curr, mask, dczid_bs, end1, end2, end3;
+	u64 curr, mask, dczid, dczid_bs, dczid_dzp, end1, end2, end3;
 
 	/* Read DC G(Z)VA block size from the system register. */
-	dczid_bs = 4ul << (read_cpuid(DCZID_EL0) & 0xf);
+	dczid = read_cpuid(DCZID_EL0);
+	dczid_bs = 4ul << (dczid & 0xf);
+	dczid_dzp = (dczid >> 4) & 1;
 
 	curr = (u64)__tag_set(addr, tag);
 	mask = dczid_bs - 1;
@@ -106,7 +109,7 @@
 	 */
 #define SET_MEMTAG_RANGE(stg_post, dc_gva)		\
 	do {						\
-		if (size >= 2 * dczid_bs) {		\
+		if (!dczid_dzp && size >= 2 * dczid_bs) {\
 			do {				\
 				curr = stg_post(curr);	\
 			} while (curr < end1);		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/mte.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/mte.h
@@ -40,7 +40,9 @@
 void mte_copy_page_tags(void *kto, const void *kfrom);
 void mte_thread_init_user(void);
 void mte_thread_switch(struct task_struct *next);
+void mte_cpu_setup(void);
 void mte_suspend_enter(void);
+void mte_suspend_exit(void);
 long set_mte_ctrl(struct task_struct *task, unsigned long arg);
 long get_mte_ctrl(struct task_struct *task);
 int mte_ptrace_copy_tags(struct task_struct *child, long request,
@@ -69,6 +71,9 @@
 static inline void mte_suspend_enter(void)
 {
 }
+static inline void mte_suspend_exit(void)
+{
+}
 static inline long set_mte_ctrl(struct task_struct *task, unsigned long arg)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/page.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/page.h
@@ -41,7 +41,6 @@
 
 typedef struct page *pgtable_t;
 
-int pfn_valid(unsigned long pfn);
 int pfn_is_map_memory(unsigned long pfn);
 
 #include <asm/memory.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/pgalloc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/pgalloc.h
@@ -76,7 +76,7 @@
 static inline void
 pmd_populate_kernel(struct mm_struct *mm, pmd_t *pmdp, pte_t *ptep)
 {
-	VM_BUG_ON(mm != &init_mm);
+	VM_BUG_ON(mm && mm != &init_mm);
 	__pmd_populate(pmdp, __pa(ptep), PMD_TYPE_TABLE | PMD_TABLE_UXN);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/pgtable-hwdef.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/pgtable-hwdef.h
@@ -273,6 +273,8 @@
 #define TCR_NFD1		(UL(1) << 54)
 #define TCR_E0PD0		(UL(1) << 55)
 #define TCR_E0PD1		(UL(1) << 56)
+#define TCR_TCMA0		(UL(1) << 57)
+#define TCR_TCMA1		(UL(1) << 58)
 
 /*
  * TTBR.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/pgtable-prot.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/pgtable-prot.h
@@ -92,7 +92,7 @@
 #define __P001  PAGE_READONLY
 #define __P010  PAGE_READONLY
 #define __P011  PAGE_READONLY
-#define __P100  PAGE_EXECONLY
+#define __P100  PAGE_READONLY_EXEC	/* PAGE_EXECONLY if Enhanced PAN */
 #define __P101  PAGE_READONLY_EXEC
 #define __P110  PAGE_READONLY_EXEC
 #define __P111  PAGE_READONLY_EXEC
@@ -101,7 +101,7 @@
 #define __S001  PAGE_READONLY
 #define __S010  PAGE_SHARED
 #define __S011  PAGE_SHARED
-#define __S100  PAGE_EXECONLY
+#define __S100  PAGE_READONLY_EXEC	/* PAGE_EXECONLY if Enhanced PAN */
 #define __S101  PAGE_READONLY_EXEC
 #define __S110  PAGE_SHARED_EXEC
 #define __S111  PAGE_SHARED_EXEC
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/pgtable.h
@@ -67,9 +67,15 @@
  * page table entry, taking care of 52-bit addresses.
  */
 #ifdef CONFIG_ARM64_PA_BITS_52
-#define __pte_to_phys(pte)	\
-	((pte_val(pte) & PTE_ADDR_LOW) | ((pte_val(pte) & PTE_ADDR_HIGH) << 36))
-#define __phys_to_pte_val(phys)	(((phys) | ((phys) >> 36)) & PTE_ADDR_MASK)
+static inline phys_addr_t __pte_to_phys(pte_t pte)
+{
+	return (pte_val(pte) & PTE_ADDR_LOW) |
+		((pte_val(pte) & PTE_ADDR_HIGH) << 36);
+}
+static inline pteval_t __phys_to_pte_val(phys_addr_t phys)
+{
+	return (phys | (phys >> 36)) & PTE_ADDR_MASK;
+}
 #else
 #define __pte_to_phys(pte)	(pte_val(pte) & PTE_ADDR_MASK)
 #define __phys_to_pte_val(phys)	(phys)
@@ -529,7 +535,7 @@
 				 PMD_TYPE_TABLE)
 #define pmd_sect(pmd)		((pmd_val(pmd) & PMD_TYPE_MASK) == \
 				 PMD_TYPE_SECT)
-#define pmd_leaf(pmd)		pmd_sect(pmd)
+#define pmd_leaf(pmd)		(pmd_present(pmd) && !pmd_table(pmd))
 #define pmd_bad(pmd)		(!pmd_table(pmd))
 
 #define pmd_leaf_size(pmd)	(pmd_cont(pmd) ? CONT_PMD_SIZE : PMD_SIZE)
@@ -619,7 +625,7 @@
 #define pud_none(pud)		(!pud_val(pud))
 #define pud_bad(pud)		(!pud_table(pud))
 #define pud_present(pud)	pte_present(pud_pte(pud))
-#define pud_leaf(pud)		pud_sect(pud)
+#define pud_leaf(pud)		(pud_present(pud) && !pud_table(pud))
 #define pud_valid(pud)		pte_valid(pud_pte(pud))
 
 static inline void set_pud(pud_t *pudp, pud_t pud)
@@ -760,6 +766,12 @@
 	if (pte_hw_dirty(pte))
 		pte = pte_mkdirty(pte);
 	pte_val(pte) = (pte_val(pte) & ~mask) | (pgprot_val(newprot) & mask);
+	/*
+	 * If we end up clearing hw dirtiness for a sw-dirty PTE, set hardware
+	 * dirtiness again.
+	 */
+	if (pte_sw_dirty(pte))
+		pte = pte_mkdirty(pte);
 	return pte;
 }
 
@@ -1011,18 +1023,6 @@
 }
 #define arch_wants_old_prefaulted_pte	arch_wants_old_prefaulted_pte
 
-static inline pgprot_t arch_filter_pgprot(pgprot_t prot)
-{
-	if (cpus_have_const_cap(ARM64_HAS_EPAN))
-		return prot;
-
-	if (pgprot_val(prot) != pgprot_val(PAGE_EXECONLY))
-		return prot;
-
-	return PAGE_READONLY_EXEC;
-}
-
-
 #endif /* !__ASSEMBLY__ */
 
 #endif /* __ASM_PGTABLE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/processor.h
@@ -204,8 +204,9 @@
 
 static inline void start_thread_common(struct pt_regs *regs, unsigned long pc)
 {
+	s32 previous_syscall = regs->syscallno;
 	memset(regs, 0, sizeof(*regs));
-	forget_syscall(regs);
+	regs->syscallno = previous_syscall;
 	regs->pc = pc;
 
 	if (system_uses_irq_prio_masking())
@@ -239,13 +240,13 @@
 }
 #endif
 
-static inline bool is_ttbr0_addr(unsigned long addr)
+static __always_inline bool is_ttbr0_addr(unsigned long addr)
 {
 	/* entry assembly clears tags for TTBR0 addrs */
 	return addr < TASK_SIZE;
 }
 
-static inline bool is_ttbr1_addr(unsigned long addr)
+static __always_inline bool is_ttbr1_addr(unsigned long addr)
 {
 	/* TTBR1 addresses may have a tag if KASAN_SW_TAGS is in use */
 	return arch_kasan_reset_tag(addr) >= PAGE_OFFSET;
@@ -335,12 +336,10 @@
  * of header definitions for the use of task_stack_page.
  */
 
-#define current_top_of_stack()								\
-({											\
-	struct stack_info _info;							\
-	BUG_ON(!on_accessible_stack(current, current_stack_pointer, 1, &_info));	\
-	_info.high;									\
-})
+/*
+ * The top of the current task's task stack
+ */
+#define current_top_of_stack()	((unsigned long)current->stack + THREAD_SIZE)
 #define on_thread_stack()	(on_task_stack(current, current_stack_pointer, 1, NULL))
 
 #endif /* __ASSEMBLY__ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/rwonce.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/rwonce.h
@@ -5,7 +5,7 @@
 #ifndef __ASM_RWONCE_H
 #define __ASM_RWONCE_H
 
-#ifdef CONFIG_LTO
+#if defined(CONFIG_LTO) && !defined(__ASSEMBLY__)
 
 #include <linux/compiler_types.h>
 #include <asm/alternative-macros.h>
@@ -66,7 +66,7 @@
 })
 
 #endif	/* !BUILD_VDSO */
-#endif	/* CONFIG_LTO */
+#endif	/* CONFIG_LTO && !__ASSEMBLY__ */
 
 #include <asm-generic/rwonce.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/scs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/scs.h
@@ -9,15 +9,16 @@
 #ifdef CONFIG_SHADOW_CALL_STACK
 	scs_sp	.req	x18
 
-	.macro scs_load tsk
-	ldr	scs_sp, [\tsk, #TSK_TI_SCS_SP]
+	.macro scs_load_current
+	get_current_task scs_sp
+	ldr	scs_sp, [scs_sp, #TSK_TI_SCS_SP]
 	.endm
 
 	.macro scs_save tsk
 	str	scs_sp, [\tsk, #TSK_TI_SCS_SP]
 	.endm
 #else
-	.macro scs_load tsk
+	.macro scs_load_current
 	.endm
 
 	.macro scs_save tsk
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/sdei.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/sdei.h
@@ -17,6 +17,9 @@
 
 #include <asm/virt.h>
 
+DECLARE_PER_CPU(struct sdei_registered_event *, sdei_active_normal_event);
+DECLARE_PER_CPU(struct sdei_registered_event *, sdei_active_critical_event);
+
 extern unsigned long sdei_exit_mode;
 
 /* Software Delegated Exception entry point from firmware*/
@@ -29,6 +32,9 @@
 						   unsigned long pc,
 						   unsigned long pstate);
 
+/* Abort a running handler. Context is discarded. */
+void __sdei_handler_abort(void);
+
 /*
  * The above entry point does the minimum to call C code. This function does
  * anything else, before calling the driver.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/sections.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/sections.h
@@ -22,4 +22,9 @@
 extern char __mmuoff_data_start[], __mmuoff_data_end[];
 extern char __entry_tramp_text_start[], __entry_tramp_text_end[];
 
+static inline size_t entry_tramp_text_size(void)
+{
+	return __entry_tramp_text_end - __entry_tramp_text_start;
+}
+
 #endif /* __ASM_SECTIONS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/spectre.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/spectre.h
@@ -26,6 +26,7 @@
 	SPECTRE_VULNERABLE,
 };
 
+struct pt_regs;
 struct task_struct;
 
 /*
@@ -67,7 +68,8 @@
 
 DECLARE_PER_CPU_READ_MOSTLY(struct bp_hardening_data, bp_hardening_data);
 
-static inline void arm64_apply_bp_hardening(void)
+/* Called during entry so must be __always_inline */
+static __always_inline void arm64_apply_bp_hardening(void)
 {
 	struct bp_hardening_data *d;
 
@@ -93,5 +95,10 @@
 
 enum mitigation_state arm64_get_meltdown_state(void);
 
+enum mitigation_state arm64_get_spectre_bhb_state(void);
+bool is_spectre_bhb_affected(const struct arm64_cpu_capabilities *entry, int scope);
+u8 spectre_bhb_loop_affected(int scope);
+void spectre_bhb_enable_mitigation(const struct arm64_cpu_capabilities *__unused);
+bool try_emulate_el1_ssbs(struct pt_regs *regs, u32 instr);
 #endif	/* __ASSEMBLY__ */
 #endif	/* __ASM_SPECTRE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/stage2_pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/stage2_pgtable.h
@@ -11,13 +11,6 @@
 #include <linux/pgtable.h>
 
 /*
- * PGDIR_SHIFT determines the size a top-level page table entry can map
- * and depends on the number of levels in the page table. Compute the
- * PGDIR_SHIFT for a given number of levels.
- */
-#define pt_levels_pgdir_shift(lvls)	ARM64_HW_PGTABLE_LEVEL_SHIFT(4 - (lvls))
-
-/*
  * The hardware supports concatenation of up to 16 tables at stage2 entry
  * level and we use the feature whenever possible, which means we resolve 4
  * additional bits of address at the entry level.
@@ -30,11 +23,6 @@
 #define stage2_pgtable_levels(ipa)	ARM64_HW_PGTABLE_LEVELS((ipa) - 4)
 #define kvm_stage2_levels(kvm)		VTCR_EL2_LVLS(kvm->arch.vtcr)
 
-/* stage2_pgdir_shift() is the size mapped by top-level stage2 entry for the VM */
-#define stage2_pgdir_shift(kvm)		pt_levels_pgdir_shift(kvm_stage2_levels(kvm))
-#define stage2_pgdir_size(kvm)		(1ULL << stage2_pgdir_shift(kvm))
-#define stage2_pgdir_mask(kvm)		~(stage2_pgdir_size(kvm) - 1)
-
 /*
  * kvm_mmmu_cache_min_pages() is the number of pages required to install
  * a stage-2 translation. We pre-allocate the entry level page table at
@@ -42,12 +30,4 @@
  */
 #define kvm_mmu_cache_min_pages(kvm)	(kvm_stage2_levels(kvm) - 1)
 
-static inline phys_addr_t
-stage2_pgd_addr_end(struct kvm *kvm, phys_addr_t addr, phys_addr_t end)
-{
-	phys_addr_t boundary = (addr + stage2_pgdir_size(kvm)) & stage2_pgdir_mask(kvm);
-
-	return (boundary - 1 < end - 1) ? boundary : end;
-}
-
 #endif	/* __ARM64_S2_PGTABLE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/syscall_wrapper.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/syscall_wrapper.h
@@ -8,7 +8,7 @@
 #ifndef __ASM_SYSCALL_WRAPPER_H
 #define __ASM_SYSCALL_WRAPPER_H
 
-struct pt_regs;
+#include <asm/ptrace.h>
 
 #define SC_ARM64_REGS_TO_ARGS(x, ...)				\
 	__MAP(x,__SC_ARGS					\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/sysreg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/sysreg.h
@@ -109,8 +109,14 @@
 #define SB_BARRIER_INSN			__SYS_BARRIER_INSN(0, 7, 31)
 
 #define SYS_DC_ISW			sys_insn(1, 0, 7, 6, 2)
+#define SYS_DC_IGSW			sys_insn(1, 0, 7, 6, 4)
+#define SYS_DC_IGDSW			sys_insn(1, 0, 7, 6, 6)
 #define SYS_DC_CSW			sys_insn(1, 0, 7, 10, 2)
+#define SYS_DC_CGSW			sys_insn(1, 0, 7, 10, 4)
+#define SYS_DC_CGDSW			sys_insn(1, 0, 7, 10, 6)
 #define SYS_DC_CISW			sys_insn(1, 0, 7, 14, 2)
+#define SYS_DC_CIGSW			sys_insn(1, 0, 7, 14, 4)
+#define SYS_DC_CIGDSW			sys_insn(1, 0, 7, 14, 6)
 
 /*
  * System registers, organised loosely by encoding but grouped together
@@ -180,6 +186,7 @@
 
 #define SYS_ID_AA64ISAR0_EL1		sys_reg(3, 0, 0, 6, 0)
 #define SYS_ID_AA64ISAR1_EL1		sys_reg(3, 0, 0, 6, 1)
+#define SYS_ID_AA64ISAR2_EL1		sys_reg(3, 0, 0, 6, 2)
 
 #define SYS_ID_AA64MMFR0_EL1		sys_reg(3, 0, 0, 7, 0)
 #define SYS_ID_AA64MMFR1_EL1		sys_reg(3, 0, 0, 7, 1)
@@ -764,6 +771,21 @@
 #define ID_AA64ISAR1_GPI_NI			0x0
 #define ID_AA64ISAR1_GPI_IMP_DEF		0x1
 
+/* id_aa64isar2 */
+#define ID_AA64ISAR2_CLEARBHB_SHIFT	28
+#define ID_AA64ISAR2_RPRES_SHIFT	4
+#define ID_AA64ISAR2_WFXT_SHIFT		0
+
+#define ID_AA64ISAR2_RPRES_8BIT		0x0
+#define ID_AA64ISAR2_RPRES_12BIT	0x1
+/*
+ * Value 0x1 has been removed from the architecture, and is
+ * reserved, but has not yet been removed from the ARM ARM
+ * as of ARM DDI 0487G.b.
+ */
+#define ID_AA64ISAR2_WFXT_NI		0x0
+#define ID_AA64ISAR2_WFXT_SUPPORTED	0x2
+
 /* id_aa64pfr0 */
 #define ID_AA64PFR0_CSV3_SHIFT		60
 #define ID_AA64PFR0_CSV2_SHIFT		56
@@ -881,6 +903,8 @@
 #endif
 
 /* id_aa64mmfr1 */
+#define ID_AA64MMFR1_ECBHB_SHIFT	60
+#define ID_AA64MMFR1_AFP_SHIFT		44
 #define ID_AA64MMFR1_ETS_SHIFT		36
 #define ID_AA64MMFR1_TWED_SHIFT		32
 #define ID_AA64MMFR1_XNX_SHIFT		28
@@ -1076,10 +1100,6 @@
 #define CPACR_EL1_ZEN_EL0EN	(BIT(17)) /* enable EL0 access, if EL1EN set */
 #define CPACR_EL1_ZEN		(CPACR_EL1_ZEN_EL1EN | CPACR_EL1_ZEN_EL0EN)
 
-/* TCR EL1 Bit Definitions */
-#define SYS_TCR_EL1_TCMA1	(BIT(58))
-#define SYS_TCR_EL1_TCMA0	(BIT(57))
-
 /* GCR_EL1 Definitions */
 #define SYS_GCR_EL1_RRND	(BIT(16))
 #define SYS_GCR_EL1_EXCL_MASK	0xffffUL
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/system_misc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/system_misc.h
@@ -18,14 +18,14 @@
 
 struct pt_regs;
 
-void die(const char *msg, struct pt_regs *regs, int err);
+void die(const char *msg, struct pt_regs *regs, long err);
 
 struct siginfo;
 void arm64_notify_die(const char *str, struct pt_regs *regs,
 		      int signo, int sicode, unsigned long far,
-		      int err);
+		      unsigned long err);
 
-void hook_debug_fault_code(int nr, int (*fn)(unsigned long, unsigned int,
+void hook_debug_fault_code(int nr, int (*fn)(unsigned long, unsigned long,
 					     struct pt_regs *),
 			   int sig, int code, const char *name);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/traps.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/traps.h
@@ -13,18 +13,17 @@
 
 struct pt_regs;
 
-struct undef_hook {
-	struct list_head node;
-	u32 instr_mask;
-	u32 instr_val;
-	u64 pstate_mask;
-	u64 pstate_val;
-	int (*fn)(struct pt_regs *regs, u32 instr);
-};
-
-void register_undef_hook(struct undef_hook *hook);
-void unregister_undef_hook(struct undef_hook *hook);
-void force_signal_inject(int signal, int code, unsigned long address, unsigned int err);
+#ifdef CONFIG_ARMV8_DEPRECATED
+bool try_emulate_armv8_deprecated(struct pt_regs *regs, u32 insn);
+#else
+static inline bool
+try_emulate_armv8_deprecated(struct pt_regs *regs, u32 insn)
+{
+	return false;
+}
+#endif /* CONFIG_ARMV8_DEPRECATED */
+
+void force_signal_inject(int signal, int code, unsigned long address, unsigned long err);
 void arm64_notify_segfault(unsigned long addr);
 void arm64_force_sig_fault(int signo, int code, unsigned long far, const char *str);
 void arm64_force_sig_mceerr(int code, unsigned long far, short lsb, const char *str);
@@ -57,7 +56,7 @@
  * errors share the same encoding as an all-zeros encoding from a CPU that
  * doesn't support RAS.
  */
-static inline bool arm64_is_ras_serror(u32 esr)
+static inline bool arm64_is_ras_serror(unsigned long esr)
 {
 	WARN_ON(preemptible());
 
@@ -77,9 +76,9 @@
  * We treat them as Uncontainable.
  * Non-RAS SError's are reported as Uncontained/Uncategorized.
  */
-static inline u32 arm64_ras_serror_get_severity(u32 esr)
+static inline unsigned long arm64_ras_serror_get_severity(unsigned long esr)
 {
-	u32 aet = esr & ESR_ELx_AET;
+	unsigned long aet = esr & ESR_ELx_AET;
 
 	if (!arm64_is_ras_serror(esr)) {
 		/* Not a RAS error, we can't interpret the ESR. */
@@ -98,6 +97,6 @@
 	return aet;
 }
 
-bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned int esr);
-void __noreturn arm64_serror_panic(struct pt_regs *regs, u32 esr);
+bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned long esr);
+void __noreturn arm64_serror_panic(struct pt_regs *regs, unsigned long esr);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/uaccess.h
@@ -292,12 +292,22 @@
 	(x) = (__force __typeof__(*(ptr)))__gu_val;			\
 } while (0)
 
+/*
+ * We must not call into the scheduler between uaccess_ttbr0_enable() and
+ * uaccess_ttbr0_disable(). As `x` and `ptr` could contain blocking functions,
+ * we must evaluate these outside of the critical section.
+ */
 #define __raw_get_user(x, ptr, err)					\
 do {									\
+	__typeof__(*(ptr)) __user *__rgu_ptr = (ptr);			\
+	__typeof__(x) __rgu_val;					\
 	__chk_user_ptr(ptr);						\
+									\
 	uaccess_ttbr0_enable();						\
-	__raw_get_mem("ldtr", x, ptr, err);				\
+	__raw_get_mem("ldtr", __rgu_val, __rgu_ptr, err);		\
 	uaccess_ttbr0_disable();					\
+									\
+	(x) = __rgu_val;						\
 } while (0)
 
 #define __get_user_error(x, ptr, err)					\
@@ -321,14 +331,22 @@
 
 #define get_user	__get_user
 
+/*
+ * We must not call into the scheduler between __uaccess_enable_tco_async() and
+ * __uaccess_disable_tco_async(). As `dst` and `src` may contain blocking
+ * functions, we must evaluate these outside of the critical section.
+ */
 #define __get_kernel_nofault(dst, src, type, err_label)			\
 do {									\
+	__typeof__(dst) __gkn_dst = (dst);				\
+	__typeof__(src) __gkn_src = (src);				\
 	int __gkn_err = 0;						\
 									\
 	__uaccess_enable_tco_async();					\
-	__raw_get_mem("ldr", *((type *)(dst)),				\
-		      (__force type *)(src), __gkn_err);		\
+	__raw_get_mem("ldr", *((type *)(__gkn_dst)),			\
+		      (__force type *)(__gkn_src), __gkn_err);		\
 	__uaccess_disable_tco_async();					\
+									\
 	if (unlikely(__gkn_err))					\
 		goto err_label;						\
 } while (0)
@@ -367,11 +385,19 @@
 	}								\
 } while (0)
 
+/*
+ * We must not call into the scheduler between uaccess_ttbr0_enable() and
+ * uaccess_ttbr0_disable(). As `x` and `ptr` could contain blocking functions,
+ * we must evaluate these outside of the critical section.
+ */
 #define __raw_put_user(x, ptr, err)					\
 do {									\
-	__chk_user_ptr(ptr);						\
+	__typeof__(*(ptr)) __user *__rpu_ptr = (ptr);			\
+	__typeof__(*(ptr)) __rpu_val = (x);				\
+	__chk_user_ptr(__rpu_ptr);					\
+									\
 	uaccess_ttbr0_enable();						\
-	__raw_put_mem("sttr", x, ptr, err);				\
+	__raw_put_mem("sttr", __rpu_val, __rpu_ptr, err);		\
 	uaccess_ttbr0_disable();					\
 } while (0)
 
@@ -396,14 +422,22 @@
 
 #define put_user	__put_user
 
+/*
+ * We must not call into the scheduler between __uaccess_enable_tco_async() and
+ * __uaccess_disable_tco_async(). As `dst` and `src` may contain blocking
+ * functions, we must evaluate these outside of the critical section.
+ */
 #define __put_kernel_nofault(dst, src, type, err_label)			\
 do {									\
+	__typeof__(dst) __pkn_dst = (dst);				\
+	__typeof__(src) __pkn_src = (src);				\
 	int __pkn_err = 0;						\
 									\
 	__uaccess_enable_tco_async();					\
-	__raw_put_mem("str", *((type *)(src)),				\
-		      (__force type *)(dst), __pkn_err);		\
+	__raw_put_mem("str", *((type *)(__pkn_src)),			\
+		      (__force type *)(__pkn_dst), __pkn_err);		\
 	__uaccess_disable_tco_async();					\
+									\
 	if (unlikely(__pkn_err))					\
 		goto err_label;						\
 } while(0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/unistd32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/unistd32.h
@@ -840,7 +840,7 @@
 #define __NR_ppoll_time64 414
 __SYSCALL(__NR_ppoll_time64, compat_sys_ppoll_time64)
 #define __NR_io_pgetevents_time64 416
-__SYSCALL(__NR_io_pgetevents_time64, sys_io_pgetevents)
+__SYSCALL(__NR_io_pgetevents_time64, compat_sys_io_pgetevents_time64)
 #define __NR_recvmmsg_time64 417
 __SYSCALL(__NR_recvmmsg_time64, compat_sys_recvmmsg_time64)
 #define __NR_mq_timedsend_time64 418
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/uprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/uprobes.h
@@ -10,21 +10,19 @@
 #include <asm/insn.h>
 #include <asm/probes.h>
 
-#define MAX_UINSN_BYTES		AARCH64_INSN_SIZE
-
-#define UPROBE_SWBP_INSN	BRK64_OPCODE_UPROBES
+#define UPROBE_SWBP_INSN	cpu_to_le32(BRK64_OPCODE_UPROBES)
 #define UPROBE_SWBP_INSN_SIZE	AARCH64_INSN_SIZE
-#define UPROBE_XOL_SLOT_BYTES	MAX_UINSN_BYTES
+#define UPROBE_XOL_SLOT_BYTES	AARCH64_INSN_SIZE
 
-typedef u32 uprobe_opcode_t;
+typedef __le32 uprobe_opcode_t;
 
 struct arch_uprobe_task {
 };
 
 struct arch_uprobe {
 	union {
-		u8 insn[MAX_UINSN_BYTES];
-		u8 ixol[MAX_UINSN_BYTES];
+		__le32 insn;
+		__le32 ixol;
 	};
 	struct arch_probe_insn api;
 	bool simulate;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/asm/vectors.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/asm/vectors.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2022 ARM Ltd.
+ */
+#ifndef __ASM_VECTORS_H
+#define __ASM_VECTORS_H
+
+#include <linux/bug.h>
+#include <linux/percpu.h>
+
+#include <asm/fixmap.h>
+
+extern char vectors[];
+extern char tramp_vectors[];
+extern char __bp_harden_el1_vectors[];
+
+/*
+ * Note: the order of this enum corresponds to two arrays in entry.S:
+ * tramp_vecs and __bp_harden_el1_vectors. By default the canonical
+ * 'full fat' vectors are used directly.
+ */
+enum arm64_bp_harden_el1_vectors {
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	/*
+	 * Perform the BHB loop mitigation, before branching to the canonical
+	 * vectors.
+	 */
+	EL1_VECTOR_BHB_LOOP,
+
+	/*
+	 * Make the SMC call for firmware mitigation, before branching to the
+	 * canonical vectors.
+	 */
+	EL1_VECTOR_BHB_FW,
+
+	/*
+	 * Use the ClearBHB instruction, before branching to the canonical
+	 * vectors.
+	 */
+	EL1_VECTOR_BHB_CLEAR_INSN,
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+
+	/*
+	 * Remap the kernel before branching to the canonical vectors.
+	 */
+	EL1_VECTOR_KPTI,
+};
+
+#ifndef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+#define EL1_VECTOR_BHB_LOOP		-1
+#define EL1_VECTOR_BHB_FW		-1
+#define EL1_VECTOR_BHB_CLEAR_INSN	-1
+#endif /* !CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+
+/* The vectors to use on return from EL0. e.g. to remap the kernel */
+DECLARE_PER_CPU_READ_MOSTLY(const char *, this_cpu_vector);
+
+#ifndef CONFIG_UNMAP_KERNEL_AT_EL0
+#define TRAMP_VALIAS	0ul
+#endif
+
+static inline const char *
+arm64_get_bp_hardening_vector(enum arm64_bp_harden_el1_vectors slot)
+{
+	if (arm64_kernel_unmapped_at_el0())
+		return (char *)(TRAMP_VALIAS + SZ_2K * slot);
+
+	WARN_ON_ONCE(slot == EL1_VECTOR_KPTI);
+
+	return __bp_harden_el1_vectors + SZ_2K * slot;
+}
+
+#endif /* __ASM_VECTORS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/uapi/asm/hwcap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/uapi/asm/hwcap.h
@@ -75,5 +75,8 @@
 #define HWCAP2_RNG		(1 << 16)
 #define HWCAP2_BTI		(1 << 17)
 #define HWCAP2_MTE		(1 << 18)
+#define HWCAP2_ECV		(1 << 19)
+#define HWCAP2_AFP		(1 << 20)
+#define HWCAP2_RPRES		(1 << 21)
 
 #endif /* _UAPI__ASM_HWCAP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/include/uapi/asm/kvm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/include/uapi/asm/kvm.h
@@ -281,6 +281,11 @@
 #define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED	3
 #define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_ENABLED     	(1U << 4)
 
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3	KVM_REG_ARM_FW_REG(3)
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_AVAIL		0
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_AVAIL		1
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_REQUIRED	2
+
 /* SVE registers */
 #define KVM_REG_ARM64_SVE		(0x15 << KVM_REG_ARM_COPROC_SHIFT)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/Makefile
@@ -74,6 +74,10 @@
 obj-y					+= vdso-wrap.o
 obj-$(CONFIG_COMPAT_VDSO)		+= vdso32-wrap.o
 
+# Force dependency (vdso*-wrap.S includes vdso.so through incbin)
+$(obj)/vdso-wrap.o: $(obj)/vdso/vdso.so
+$(obj)/vdso32-wrap.o: $(obj)/vdso32/vdso.so
+
 obj-y					+= probes/
 head-y					:= head.o
 extra-y					+= $(head-y) vmlinux.lds
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/acpi_numa.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/acpi_numa.c
@@ -27,24 +27,13 @@
 
 #include <asm/numa.h>
 
-static int acpi_early_node_map[NR_CPUS] __initdata = { NUMA_NO_NODE };
+static int acpi_early_node_map[NR_CPUS] __initdata = { [0 ... NR_CPUS - 1] = NUMA_NO_NODE };
 
 int __init acpi_numa_get_nid(unsigned int cpu)
 {
 	return acpi_early_node_map[cpu];
 }
 
-static inline int get_cpu_for_acpi_id(u32 uid)
-{
-	int cpu;
-
-	for (cpu = 0; cpu < nr_cpu_ids; cpu++)
-		if (uid == get_acpi_id_for_cpu(cpu))
-			return cpu;
-
-	return -EINVAL;
-}
-
 static int __init acpi_parse_gicc_pxm(union acpi_subtable_headers *header,
 				      const unsigned long end)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/alternative.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/alternative.c
@@ -42,7 +42,7 @@
 /*
  * Check if the target PC is within an alternative block.
  */
-static bool branch_insn_requires_update(struct alt_instr *alt, unsigned long pc)
+static __always_inline bool branch_insn_requires_update(struct alt_instr *alt, unsigned long pc)
 {
 	unsigned long replptr = (unsigned long)ALT_REPL_PTR(alt);
 	return !(pc >= replptr && pc <= (replptr + alt->alt_len));
@@ -50,7 +50,7 @@
 
 #define align_down(x, a)	((unsigned long)(x) & ~(((unsigned long)(a)) - 1))
 
-static u32 get_alt_insn(struct alt_instr *alt, __le32 *insnptr, __le32 *altinsnptr)
+static __always_inline u32 get_alt_insn(struct alt_instr *alt, __le32 *insnptr, __le32 *altinsnptr)
 {
 	u32 insn;
 
@@ -95,7 +95,7 @@
 	return insn;
 }
 
-static void patch_alternative(struct alt_instr *alt,
+static noinstr void patch_alternative(struct alt_instr *alt,
 			      __le32 *origptr, __le32 *updptr, int nr_inst)
 {
 	__le32 *replptr;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/armv8_deprecated.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/armv8_deprecated.c
@@ -17,7 +17,6 @@
 #include <asm/sysreg.h>
 #include <asm/system_misc.h>
 #include <asm/traps.h>
-#include <asm/kprobes.h>
 
 #define CREATE_TRACE_POINTS
 #include "trace-events-emulation.h"
@@ -39,225 +38,46 @@
 enum legacy_insn_status {
 	INSN_DEPRECATED,
 	INSN_OBSOLETE,
-};
-
-struct insn_emulation_ops {
-	const char		*name;
-	enum legacy_insn_status	status;
-	struct undef_hook	*hooks;
-	int			(*set_hw_mode)(bool enable);
+	INSN_UNAVAILABLE,
 };
 
 struct insn_emulation {
-	struct list_head node;
-	struct insn_emulation_ops *ops;
+	const char			*name;
+	enum legacy_insn_status		status;
+	bool				(*try_emulate)(struct pt_regs *regs,
+						       u32 insn);
+	int				(*set_hw_mode)(bool enable);
+
 	int current_mode;
 	int min;
 	int max;
-};
-
-static LIST_HEAD(insn_emulation);
-static int nr_insn_emulated __initdata;
-static DEFINE_RAW_SPINLOCK(insn_emulation_lock);
-
-static void register_emulation_hooks(struct insn_emulation_ops *ops)
-{
-	struct undef_hook *hook;
-
-	BUG_ON(!ops->hooks);
-
-	for (hook = ops->hooks; hook->instr_mask; hook++)
-		register_undef_hook(hook);
-
-	pr_notice("Registered %s emulation handler\n", ops->name);
-}
 
-static void remove_emulation_hooks(struct insn_emulation_ops *ops)
-{
-	struct undef_hook *hook;
-
-	BUG_ON(!ops->hooks);
-
-	for (hook = ops->hooks; hook->instr_mask; hook++)
-		unregister_undef_hook(hook);
-
-	pr_notice("Removed %s emulation handler\n", ops->name);
-}
-
-static void enable_insn_hw_mode(void *data)
-{
-	struct insn_emulation *insn = (struct insn_emulation *)data;
-	if (insn->ops->set_hw_mode)
-		insn->ops->set_hw_mode(true);
-}
-
-static void disable_insn_hw_mode(void *data)
-{
-	struct insn_emulation *insn = (struct insn_emulation *)data;
-	if (insn->ops->set_hw_mode)
-		insn->ops->set_hw_mode(false);
-}
-
-/* Run set_hw_mode(mode) on all active CPUs */
-static int run_all_cpu_set_hw_mode(struct insn_emulation *insn, bool enable)
-{
-	if (!insn->ops->set_hw_mode)
-		return -EINVAL;
-	if (enable)
-		on_each_cpu(enable_insn_hw_mode, (void *)insn, true);
-	else
-		on_each_cpu(disable_insn_hw_mode, (void *)insn, true);
-	return 0;
-}
-
-/*
- * Run set_hw_mode for all insns on a starting CPU.
- * Returns:
- *  0 		- If all the hooks ran successfully.
- * -EINVAL	- At least one hook is not supported by the CPU.
- */
-static int run_all_insn_set_hw_mode(unsigned int cpu)
-{
-	int rc = 0;
-	unsigned long flags;
-	struct insn_emulation *insn;
-
-	raw_spin_lock_irqsave(&insn_emulation_lock, flags);
-	list_for_each_entry(insn, &insn_emulation, node) {
-		bool enable = (insn->current_mode == INSN_HW);
-		if (insn->ops->set_hw_mode && insn->ops->set_hw_mode(enable)) {
-			pr_warn("CPU[%u] cannot support the emulation of %s",
-				cpu, insn->ops->name);
-			rc = -EINVAL;
-		}
-	}
-	raw_spin_unlock_irqrestore(&insn_emulation_lock, flags);
-	return rc;
-}
-
-static int update_insn_emulation_mode(struct insn_emulation *insn,
-				       enum insn_emulation_mode prev)
-{
-	int ret = 0;
-
-	switch (prev) {
-	case INSN_UNDEF: /* Nothing to be done */
-		break;
-	case INSN_EMULATE:
-		remove_emulation_hooks(insn->ops);
-		break;
-	case INSN_HW:
-		if (!run_all_cpu_set_hw_mode(insn, false))
-			pr_notice("Disabled %s support\n", insn->ops->name);
-		break;
-	}
-
-	switch (insn->current_mode) {
-	case INSN_UNDEF:
-		break;
-	case INSN_EMULATE:
-		register_emulation_hooks(insn->ops);
-		break;
-	case INSN_HW:
-		ret = run_all_cpu_set_hw_mode(insn, true);
-		if (!ret)
-			pr_notice("Enabled %s support\n", insn->ops->name);
-		break;
-	}
-
-	return ret;
-}
-
-static void __init register_insn_emulation(struct insn_emulation_ops *ops)
-{
-	unsigned long flags;
-	struct insn_emulation *insn;
-
-	insn = kzalloc(sizeof(*insn), GFP_KERNEL);
-	if (!insn)
-		return;
-
-	insn->ops = ops;
-	insn->min = INSN_UNDEF;
-
-	switch (ops->status) {
-	case INSN_DEPRECATED:
-		insn->current_mode = INSN_EMULATE;
-		/* Disable the HW mode if it was turned on at early boot time */
-		run_all_cpu_set_hw_mode(insn, false);
-		insn->max = INSN_HW;
-		break;
-	case INSN_OBSOLETE:
-		insn->current_mode = INSN_UNDEF;
-		insn->max = INSN_EMULATE;
-		break;
-	}
-
-	raw_spin_lock_irqsave(&insn_emulation_lock, flags);
-	list_add(&insn->node, &insn_emulation);
-	nr_insn_emulated++;
-	raw_spin_unlock_irqrestore(&insn_emulation_lock, flags);
-
-	/* Register any handlers if required */
-	update_insn_emulation_mode(insn, INSN_UNDEF);
-}
-
-static int emulation_proc_handler(struct ctl_table *table, int write,
-				  void *buffer, size_t *lenp,
-				  loff_t *ppos)
-{
-	int ret = 0;
-	struct insn_emulation *insn = (struct insn_emulation *) table->data;
-	enum insn_emulation_mode prev_mode = insn->current_mode;
-
-	table->data = &insn->current_mode;
-	ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
+	/*
+	 * sysctl for this emulation + a sentinal entry.
+	 */
+	struct ctl_table sysctl[2];
+};
 
-	if (ret || !write || prev_mode == insn->current_mode)
-		goto ret;
+#define ARM_OPCODE_CONDTEST_FAIL   0
+#define ARM_OPCODE_CONDTEST_PASS   1
+#define ARM_OPCODE_CONDTEST_UNCOND 2
 
-	ret = update_insn_emulation_mode(insn, prev_mode);
-	if (ret) {
-		/* Mode change failed, revert to previous mode. */
-		insn->current_mode = prev_mode;
-		update_insn_emulation_mode(insn, INSN_UNDEF);
-	}
-ret:
-	table->data = insn;
-	return ret;
-}
+#define	ARM_OPCODE_CONDITION_UNCOND	0xf
 
-static void __init register_insn_emulation_sysctl(void)
+static unsigned int __maybe_unused aarch32_check_condition(u32 opcode, u32 psr)
 {
-	unsigned long flags;
-	int i = 0;
-	struct insn_emulation *insn;
-	struct ctl_table *insns_sysctl, *sysctl;
-
-	insns_sysctl = kcalloc(nr_insn_emulated + 1, sizeof(*sysctl),
-			       GFP_KERNEL);
-	if (!insns_sysctl)
-		return;
-
-	raw_spin_lock_irqsave(&insn_emulation_lock, flags);
-	list_for_each_entry(insn, &insn_emulation, node) {
-		sysctl = &insns_sysctl[i];
-
-		sysctl->mode = 0644;
-		sysctl->maxlen = sizeof(int);
+	u32 cc_bits  = opcode >> 28;
 
-		sysctl->procname = insn->ops->name;
-		sysctl->data = insn;
-		sysctl->extra1 = &insn->min;
-		sysctl->extra2 = &insn->max;
-		sysctl->proc_handler = emulation_proc_handler;
-		i++;
+	if (cc_bits != ARM_OPCODE_CONDITION_UNCOND) {
+		if ((*aarch32_opcode_cond_checks[cc_bits])(psr))
+			return ARM_OPCODE_CONDTEST_PASS;
+		else
+			return ARM_OPCODE_CONDTEST_FAIL;
 	}
-	raw_spin_unlock_irqrestore(&insn_emulation_lock, flags);
-
-	register_sysctl("abi", insns_sysctl);
+	return ARM_OPCODE_CONDTEST_UNCOND;
 }
 
+#ifdef CONFIG_SWP_EMULATION
 /*
  *  Implement emulation of the SWP/SWPB instructions using load-exclusive and
  *  store-exclusive.
@@ -344,25 +164,6 @@
 	return res;
 }
 
-#define ARM_OPCODE_CONDTEST_FAIL   0
-#define ARM_OPCODE_CONDTEST_PASS   1
-#define ARM_OPCODE_CONDTEST_UNCOND 2
-
-#define	ARM_OPCODE_CONDITION_UNCOND	0xf
-
-static unsigned int __kprobes aarch32_check_condition(u32 opcode, u32 psr)
-{
-	u32 cc_bits  = opcode >> 28;
-
-	if (cc_bits != ARM_OPCODE_CONDITION_UNCOND) {
-		if ((*aarch32_opcode_cond_checks[cc_bits])(psr))
-			return ARM_OPCODE_CONDTEST_PASS;
-		else
-			return ARM_OPCODE_CONDTEST_FAIL;
-	}
-	return ARM_OPCODE_CONDTEST_UNCOND;
-}
-
 /*
  * swp_handler logs the id of calling process, dissects the instruction, sanity
  * checks the memory location, calls emulate_swpX for the actual operation and
@@ -435,28 +236,27 @@
 	return 0;
 }
 
-/*
- * Only emulate SWP/SWPB executed in ARM state/User mode.
- * The kernel must be SWP free and SWP{B} does not exist in Thumb.
- */
-static struct undef_hook swp_hooks[] = {
-	{
-		.instr_mask	= 0x0fb00ff0,
-		.instr_val	= 0x01000090,
-		.pstate_mask	= PSR_AA32_MODE_MASK,
-		.pstate_val	= PSR_AA32_MODE_USR,
-		.fn		= swp_handler
-	},
-	{ }
-};
+static bool try_emulate_swp(struct pt_regs *regs, u32 insn)
+{
+	/* SWP{B} only exists in ARM state and does not exist in Thumb */
+	if (!compat_user_mode(regs) || compat_thumb_mode(regs))
+		return false;
 
-static struct insn_emulation_ops swp_ops = {
+	if ((insn & 0x0fb00ff0) != 0x01000090)
+		return false;
+
+	return swp_handler(regs, insn) == 0;
+}
+
+static struct insn_emulation insn_swp = {
 	.name = "swp",
 	.status = INSN_OBSOLETE,
-	.hooks = swp_hooks,
+	.try_emulate = try_emulate_swp,
 	.set_hw_mode = NULL,
 };
+#endif /* CONFIG_SWP_EMULATION */
 
+#ifdef CONFIG_CP15_BARRIER_EMULATION
 static int cp15barrier_handler(struct pt_regs *regs, u32 instr)
 {
 	perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS, 1, regs, regs->pc);
@@ -519,31 +319,29 @@
 	return 0;
 }
 
-static struct undef_hook cp15_barrier_hooks[] = {
-	{
-		.instr_mask	= 0x0fff0fdf,
-		.instr_val	= 0x0e070f9a,
-		.pstate_mask	= PSR_AA32_MODE_MASK,
-		.pstate_val	= PSR_AA32_MODE_USR,
-		.fn		= cp15barrier_handler,
-	},
-	{
-		.instr_mask	= 0x0fff0fff,
-		.instr_val	= 0x0e070f95,
-		.pstate_mask	= PSR_AA32_MODE_MASK,
-		.pstate_val	= PSR_AA32_MODE_USR,
-		.fn		= cp15barrier_handler,
-	},
-	{ }
-};
+static bool try_emulate_cp15_barrier(struct pt_regs *regs, u32 insn)
+{
+	if (!compat_user_mode(regs) || compat_thumb_mode(regs))
+		return false;
 
-static struct insn_emulation_ops cp15_barrier_ops = {
+	if ((insn & 0x0fff0fdf) == 0x0e070f9a)
+		return cp15barrier_handler(regs, insn) == 0;
+
+	if ((insn & 0x0fff0fff) == 0x0e070f95)
+		return cp15barrier_handler(regs, insn) == 0;
+
+	return false;
+}
+
+static struct insn_emulation insn_cp15_barrier = {
 	.name = "cp15_barrier",
 	.status = INSN_DEPRECATED,
-	.hooks = cp15_barrier_hooks,
+	.try_emulate = try_emulate_cp15_barrier,
 	.set_hw_mode = cp15_barrier_set_hw_mode,
 };
+#endif /* CONFIG_CP15_BARRIER_EMULATION */
 
+#ifdef CONFIG_SETEND_EMULATION
 static int setend_set_hw_mode(bool enable)
 {
 	if (!cpu_supports_mixed_endian_el0())
@@ -591,31 +389,224 @@
 	return rc;
 }
 
-static struct undef_hook setend_hooks[] = {
-	{
-		.instr_mask	= 0xfffffdff,
-		.instr_val	= 0xf1010000,
-		.pstate_mask	= PSR_AA32_MODE_MASK,
-		.pstate_val	= PSR_AA32_MODE_USR,
-		.fn		= a32_setend_handler,
-	},
-	{
-		/* Thumb mode */
-		.instr_mask	= 0xfffffff7,
-		.instr_val	= 0x0000b650,
-		.pstate_mask	= (PSR_AA32_T_BIT | PSR_AA32_MODE_MASK),
-		.pstate_val	= (PSR_AA32_T_BIT | PSR_AA32_MODE_USR),
-		.fn		= t16_setend_handler,
-	},
-	{}
-};
+static bool try_emulate_setend(struct pt_regs *regs, u32 insn)
+{
+	if (compat_thumb_mode(regs) &&
+	    (insn & 0xfffffff7) == 0x0000b650)
+		return t16_setend_handler(regs, insn) == 0;
+
+	if (compat_user_mode(regs) &&
+	    (insn & 0xfffffdff) == 0xf1010000)
+		return a32_setend_handler(regs, insn) == 0;
 
-static struct insn_emulation_ops setend_ops = {
+	return false;
+}
+
+static struct insn_emulation insn_setend = {
 	.name = "setend",
 	.status = INSN_DEPRECATED,
-	.hooks = setend_hooks,
+	.try_emulate = try_emulate_setend,
 	.set_hw_mode = setend_set_hw_mode,
 };
+#endif /* CONFIG_SETEND_EMULATION */
+
+static struct insn_emulation *insn_emulations[] = {
+#ifdef CONFIG_SWP_EMULATION
+	&insn_swp,
+#endif
+#ifdef CONFIG_CP15_BARRIER_EMULATION
+	&insn_cp15_barrier,
+#endif
+#ifdef CONFIG_SETEND_EMULATION
+	&insn_setend,
+#endif
+};
+
+static DEFINE_MUTEX(insn_emulation_mutex);
+
+static void enable_insn_hw_mode(void *data)
+{
+	struct insn_emulation *insn = (struct insn_emulation *)data;
+	if (insn->set_hw_mode)
+		insn->set_hw_mode(true);
+}
+
+static void disable_insn_hw_mode(void *data)
+{
+	struct insn_emulation *insn = (struct insn_emulation *)data;
+	if (insn->set_hw_mode)
+		insn->set_hw_mode(false);
+}
+
+/* Run set_hw_mode(mode) on all active CPUs */
+static int run_all_cpu_set_hw_mode(struct insn_emulation *insn, bool enable)
+{
+	if (!insn->set_hw_mode)
+		return -EINVAL;
+	if (enable)
+		on_each_cpu(enable_insn_hw_mode, (void *)insn, true);
+	else
+		on_each_cpu(disable_insn_hw_mode, (void *)insn, true);
+	return 0;
+}
+
+/*
+ * Run set_hw_mode for all insns on a starting CPU.
+ * Returns:
+ *  0 		- If all the hooks ran successfully.
+ * -EINVAL	- At least one hook is not supported by the CPU.
+ */
+static int run_all_insn_set_hw_mode(unsigned int cpu)
+{
+	int i;
+	int rc = 0;
+	unsigned long flags;
+
+	/*
+	 * Disable IRQs to serialize against an IPI from
+	 * run_all_cpu_set_hw_mode(), ensuring the HW is programmed to the most
+	 * recent enablement state if the two race with one another.
+	 */
+	local_irq_save(flags);
+	for (i = 0; i < ARRAY_SIZE(insn_emulations); i++) {
+		struct insn_emulation *insn = insn_emulations[i];
+		bool enable = READ_ONCE(insn->current_mode) == INSN_HW;
+		if (insn->status == INSN_UNAVAILABLE)
+			continue;
+
+		if (insn->set_hw_mode && insn->set_hw_mode(enable)) {
+			pr_warn("CPU[%u] cannot support the emulation of %s",
+				cpu, insn->name);
+			rc = -EINVAL;
+		}
+	}
+	local_irq_restore(flags);
+
+	return rc;
+}
+
+static int update_insn_emulation_mode(struct insn_emulation *insn,
+				       enum insn_emulation_mode prev)
+{
+	int ret = 0;
+
+	switch (prev) {
+	case INSN_UNDEF: /* Nothing to be done */
+		break;
+	case INSN_EMULATE:
+		break;
+	case INSN_HW:
+		if (!run_all_cpu_set_hw_mode(insn, false))
+			pr_notice("Disabled %s support\n", insn->name);
+		break;
+	}
+
+	switch (insn->current_mode) {
+	case INSN_UNDEF:
+		break;
+	case INSN_EMULATE:
+		break;
+	case INSN_HW:
+		ret = run_all_cpu_set_hw_mode(insn, true);
+		if (!ret)
+			pr_notice("Enabled %s support\n", insn->name);
+		break;
+	}
+
+	return ret;
+}
+
+static int emulation_proc_handler(struct ctl_table *table, int write,
+				  void *buffer, size_t *lenp,
+				  loff_t *ppos)
+{
+	int ret = 0;
+	struct insn_emulation *insn = container_of(table->data, struct insn_emulation, current_mode);
+	enum insn_emulation_mode prev_mode = insn->current_mode;
+
+	mutex_lock(&insn_emulation_mutex);
+	ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
+
+	if (ret || !write || prev_mode == insn->current_mode)
+		goto ret;
+
+	ret = update_insn_emulation_mode(insn, prev_mode);
+	if (ret) {
+		/* Mode change failed, revert to previous mode. */
+		WRITE_ONCE(insn->current_mode, prev_mode);
+		update_insn_emulation_mode(insn, INSN_UNDEF);
+	}
+ret:
+	mutex_unlock(&insn_emulation_mutex);
+	return ret;
+}
+
+static void __init register_insn_emulation(struct insn_emulation *insn)
+{
+	struct ctl_table *sysctl;
+
+	insn->min = INSN_UNDEF;
+
+	switch (insn->status) {
+	case INSN_DEPRECATED:
+		insn->current_mode = INSN_EMULATE;
+		/* Disable the HW mode if it was turned on at early boot time */
+		run_all_cpu_set_hw_mode(insn, false);
+		insn->max = INSN_HW;
+		break;
+	case INSN_OBSOLETE:
+		insn->current_mode = INSN_UNDEF;
+		insn->max = INSN_EMULATE;
+		break;
+	case INSN_UNAVAILABLE:
+		insn->current_mode = INSN_UNDEF;
+		insn->max = INSN_UNDEF;
+		break;
+	}
+
+	/* Program the HW if required */
+	update_insn_emulation_mode(insn, INSN_UNDEF);
+
+	if (insn->status != INSN_UNAVAILABLE) {
+		sysctl = &insn->sysctl[0];
+
+		sysctl->mode = 0644;
+		sysctl->maxlen = sizeof(int);
+
+		sysctl->procname = insn->name;
+		sysctl->data = &insn->current_mode;
+		sysctl->extra1 = &insn->min;
+		sysctl->extra2 = &insn->max;
+		sysctl->proc_handler = emulation_proc_handler;
+
+		register_sysctl("abi", sysctl);
+	}
+}
+
+bool try_emulate_armv8_deprecated(struct pt_regs *regs, u32 insn)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(insn_emulations); i++) {
+		struct insn_emulation *ie = insn_emulations[i];
+
+		if (ie->status == INSN_UNAVAILABLE)
+			continue;
+
+		/*
+		 * A trap may race with the mode being changed
+		 * INSN_EMULATE<->INSN_HW. Try to emulate the instruction to
+		 * avoid a spurious UNDEF.
+		 */
+		if (READ_ONCE(ie->current_mode) == INSN_UNDEF)
+			continue;
+
+		if (ie->try_emulate(regs, insn))
+			return true;
+	}
+
+	return false;
+}
 
 /*
  * Invoked as core_initcall, which guarantees that the instruction
@@ -623,24 +614,27 @@
  */
 static int __init armv8_deprecated_init(void)
 {
-	if (IS_ENABLED(CONFIG_SWP_EMULATION))
-		register_insn_emulation(&swp_ops);
+	int i;
 
-	if (IS_ENABLED(CONFIG_CP15_BARRIER_EMULATION))
-		register_insn_emulation(&cp15_barrier_ops);
+#ifdef CONFIG_SETEND_EMULATION
+	if (!system_supports_mixed_endian_el0()) {
+		insn_setend.status = INSN_UNAVAILABLE;
+		pr_info("setend instruction emulation is not supported on this system\n");
+	}
 
-	if (IS_ENABLED(CONFIG_SETEND_EMULATION)) {
-		if (system_supports_mixed_endian_el0())
-			register_insn_emulation(&setend_ops);
-		else
-			pr_info("setend instruction emulation is not supported on this system\n");
+#endif
+	for (i = 0; i < ARRAY_SIZE(insn_emulations); i++) {
+		struct insn_emulation *ie = insn_emulations[i];
+
+		if (ie->status == INSN_UNAVAILABLE)
+			continue;
+
+		register_insn_emulation(ie);
 	}
 
 	cpuhp_setup_state_nocalls(CPUHP_AP_ARM64_ISNDEP_STARTING,
 				  "arm64/isndep:starting",
 				  run_all_insn_set_hw_mode, NULL);
-	register_insn_emulation_sysctl();
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/cacheinfo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/cacheinfo.c
@@ -45,7 +45,8 @@
 
 int init_cache_level(unsigned int cpu)
 {
-	unsigned int ctype, level, leaves, fw_level;
+	unsigned int ctype, level, leaves;
+	int fw_level;
 	struct cpu_cacheinfo *this_cpu_ci = get_cpu_cacheinfo(cpu);
 
 	for (level = 1, leaves = 0; level <= MAX_CACHE_LEVEL; level++) {
@@ -63,6 +64,9 @@
 	else
 		fw_level = acpi_find_last_cache_level(cpu);
 
+	if (fw_level < 0)
+		return fw_level;
+
 	if (level < fw_level) {
 		/*
 		 * some external caches not specified in CLIDR_EL1
@@ -83,16 +87,18 @@
 	unsigned int level, idx;
 	enum cache_type type;
 	struct cpu_cacheinfo *this_cpu_ci = get_cpu_cacheinfo(cpu);
-	struct cacheinfo *this_leaf = this_cpu_ci->info_list;
+	struct cacheinfo *infos = this_cpu_ci->info_list;
 
 	for (idx = 0, level = 1; level <= this_cpu_ci->num_levels &&
-	     idx < this_cpu_ci->num_leaves; idx++, level++) {
+	     idx < this_cpu_ci->num_leaves; level++) {
 		type = get_cache_type(level);
 		if (type == CACHE_TYPE_SEPARATE) {
-			ci_leaf_init(this_leaf++, CACHE_TYPE_DATA, level);
-			ci_leaf_init(this_leaf++, CACHE_TYPE_INST, level);
+			if (idx + 1 >= this_cpu_ci->num_leaves)
+				break;
+			ci_leaf_init(&infos[idx++], CACHE_TYPE_DATA, level);
+			ci_leaf_init(&infos[idx++], CACHE_TYPE_INST, level);
 		} else {
-			ci_leaf_init(this_leaf++, type, level);
+			ci_leaf_init(&infos[idx++], type, level);
 		}
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/cpu_errata.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/cpu_errata.c
@@ -209,6 +209,21 @@
 	{
 		ERRATA_MIDR_RANGE(MIDR_CORTEX_A76, 0, 0, 3, 0),
 	},
+	{
+		/* Kryo4xx Gold (rcpe to rfpe) => (r0p0 to r3p0) */
+		ERRATA_MIDR_RANGE(MIDR_QCOM_KRYO_4XX_GOLD, 0xc, 0xe, 0xf, 0xe),
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2441007
+	{
+		ERRATA_MIDR_ALL_VERSIONS(MIDR_CORTEX_A55),
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2441009
+	{
+		/* Cortex-A510 r0p0 -> r1p1. Fixed in r1p2 */
+		ERRATA_MIDR_RANGE(MIDR_CORTEX_A510, 0, 0, 1, 1),
+	},
 #endif
 	{},
 };
@@ -340,6 +355,79 @@
 };
 #endif
 
+#ifdef CONFIG_ARM64_ERRATUM_1742098
+static struct midr_range broken_aarch32_aes[] = {
+	MIDR_RANGE(MIDR_CORTEX_A57, 0, 1, 0xf, 0xf),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A72),
+	{},
+};
+#endif
+
+#ifdef CONFIG_ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+static const struct midr_range trbe_overwrite_fill_mode_cpus[] = {
+#ifdef CONFIG_ARM64_ERRATUM_2139208
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
+	MIDR_ALL_VERSIONS(MIDR_MICROSOFT_AZURE_COBALT_100),
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2119858
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+#endif
+	{},
+};
+#endif	/* CONFIG_ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE */
+
+#ifdef CONFIG_ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+static const struct midr_range tsb_flush_fail_cpus[] = {
+#ifdef CONFIG_ARM64_ERRATUM_2067961
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
+	MIDR_ALL_VERSIONS(MIDR_MICROSOFT_AZURE_COBALT_100),
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2054223
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+#endif
+	{},
+};
+#endif	/* CONFIG_ARM64_WORKAROUND_TSB_FLUSH_FAILURE */
+
+#ifdef CONFIG_ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
+static struct midr_range trbe_write_out_of_range_cpus[] = {
+#ifdef CONFIG_ARM64_ERRATUM_2253138
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
+	MIDR_ALL_VERSIONS(MIDR_MICROSOFT_AZURE_COBALT_100),
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2224489
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+#endif
+	{},
+};
+#endif /* CONFIG_ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE */
+
+#ifdef CONFIG_ARM64_ERRATUM_3194386
+static const struct midr_range erratum_spec_ssbs_list[] = {
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A76),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A77),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A78),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A78C),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A715),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A720),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A725),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_X1),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_X1C),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_X2),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_X3),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_X4),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_X925),
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N1),
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N3),
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_V1),
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_V2),
+	MIDR_ALL_VERSIONS(MIDR_NEOVERSE_V3),
+	{}
+};
+#endif
+
 const struct arm64_cpu_capabilities arm64_errata[] = {
 #ifdef CONFIG_ARM64_WORKAROUND_CLEAN_CACHE
 	{
@@ -425,7 +513,7 @@
 #endif
 #ifdef CONFIG_ARM64_WORKAROUND_REPEAT_TLBI
 	{
-		.desc = "Qualcomm erratum 1009, or ARM erratum 1286807",
+		.desc = "Qualcomm erratum 1009, or ARM erratum 1286807, 2441009",
 		.capability = ARM64_WORKAROUND_REPEAT_TLBI,
 		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
 		.matches = cpucap_multi_entry_cap_matches,
@@ -464,6 +552,13 @@
 		.matches = has_spectre_v4,
 		.cpu_enable = spectre_v4_enable_mitigation,
 	},
+	{
+		.desc = "Spectre-BHB",
+		.capability = ARM64_SPECTRE_BHB,
+		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
+		.matches = is_spectre_bhb_affected,
+		.cpu_enable = spectre_bhb_enable_mitigation,
+	},
 #ifdef CONFIG_ARM64_ERRATUM_1418040
 	{
 		.desc = "ARM erratum 1418040",
@@ -534,6 +629,59 @@
 		ERRATA_MIDR_ALL_VERSIONS(MIDR_NVIDIA_CARMEL),
 	},
 #endif
+
+#ifdef CONFIG_ARM64_ERRATUM_2457168
+	{
+		.desc = "ARM erratum 2457168",
+		.capability = ARM64_WORKAROUND_2457168,
+		.type = ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE,
+		/* Cortex-A510 r0p0-r1p1 */
+		CAP_MIDR_RANGE(MIDR_CORTEX_A510, 0, 0, 1, 1)
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_1742098
+	{
+		.desc = "ARM erratum 1742098",
+		.capability = ARM64_WORKAROUND_1742098,
+		CAP_MIDR_RANGE_LIST(broken_aarch32_aes),
+		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
+	},
+#endif
+#ifdef CONFIG_ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	{
+		/*
+		 * The erratum work around is handled within the TRBE
+		 * driver and can be applied per-cpu. So, we can allow
+		 * a late CPU to come online with this erratum.
+		 */
+		.desc = "ARM erratum 2119858 or 2139208",
+		.capability = ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE,
+		.type = ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE,
+		CAP_MIDR_RANGE_LIST(trbe_overwrite_fill_mode_cpus),
+	},
+#endif
+#ifdef CONFIG_ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+	{
+		.desc = "ARM erratum 2067961 or 2054223",
+		.capability = ARM64_WORKAROUND_TSB_FLUSH_FAILURE,
+		ERRATA_MIDR_RANGE_LIST(tsb_flush_fail_cpus),
+	},
+#endif
+#ifdef CONFIG_ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
+	{
+		.desc = "ARM erratum 2253138 or 2224489",
+		.capability = ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE,
+		.type = ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE,
+		CAP_MIDR_RANGE_LIST(trbe_write_out_of_range_cpus),
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_3194386
+	{
+		.desc = "SSBS not fully self-synchronizing",
+		.capability = ARM64_WORKAROUND_SPECULATIVE_SSBS,
+		ERRATA_MIDR_RANGE_LIST(erratum_spec_ssbs_list),
+	},
+#endif
 	{
 	}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/cpufeature.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/cpufeature.c
@@ -73,10 +73,13 @@
 #include <linux/mm.h>
 #include <linux/cpu.h>
 #include <linux/kasan.h>
+#include <linux/percpu.h>
+
 #include <asm/cpu.h>
 #include <asm/cpufeature.h>
 #include <asm/cpu_ops.h>
 #include <asm/fpsimd.h>
+#include <asm/hwcap.h>
 #include <asm/insn.h>
 #include <asm/kvm_host.h>
 #include <asm/mmu_context.h>
@@ -85,6 +88,7 @@
 #include <asm/smp.h>
 #include <asm/sysreg.h>
 #include <asm/traps.h>
+#include <asm/vectors.h>
 #include <asm/virt.h>
 
 /* Kernel representation of AT_HWCAP and AT_HWCAP2 */
@@ -110,6 +114,8 @@
 bool arm64_use_ng_mappings = false;
 EXPORT_SYMBOL(arm64_use_ng_mappings);
 
+DEFINE_PER_CPU_READ_MOSTLY(const char *, this_cpu_vector) = vectors;
+
 /*
  * Permit PER_LINUX32 and execve() of 32-bit binaries even if not all CPUs
  * support it?
@@ -225,6 +231,12 @@
 	ARM64_FTR_END,
 };
 
+static const struct arm64_ftr_bits ftr_id_aa64isar2[] = {
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_HIGHER_SAFE, ID_AA64ISAR2_CLEARBHB_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64ISAR2_RPRES_SHIFT, 4, 0),
+	ARM64_FTR_END,
+};
+
 static const struct arm64_ftr_bits ftr_id_aa64pfr0[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_CSV3_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_CSV2_SHIFT, 4, 0),
@@ -279,7 +291,7 @@
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64mmfr0[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_ECV_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_ECV_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_FGT_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EXS_SHIFT, 4, 0),
 	/*
@@ -325,6 +337,7 @@
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64mmfr1[] = {
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_AFP_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_ETS_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_TWED_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_XNX_SHIFT, 4, 0),
@@ -409,6 +422,30 @@
 	ARM64_FTR_END,
 };
 
+static const struct arm64_ftr_bits ftr_mvfr0[] = {
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPROUND_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPSHVEC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPSQRT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPDIVIDE_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPTRAP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPDP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPSP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_SIMD_SHIFT, 4, 0),
+	ARM64_FTR_END,
+};
+
+static const struct arm64_ftr_bits ftr_mvfr1[] = {
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDFMAC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_FPHP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDHP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDSP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDINT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDLS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_FPDNAN_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_FPFTZ_SHIFT, 4, 0),
+	ARM64_FTR_END,
+};
+
 static const struct arm64_ftr_bits ftr_mvfr2[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR2_FPMISC_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR2_SIMDMISC_SHIFT, 4, 0),
@@ -439,10 +476,10 @@
 
 static const struct arm64_ftr_bits ftr_id_isar5[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_RDM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_CRC32_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA2_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA1_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_AES_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_CRC32_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA1_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_AES_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SEVL_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
@@ -524,7 +561,7 @@
 
 static const struct arm64_ftr_bits ftr_id_dfr0[] = {
 	/* [31:28] TraceFilt */
-	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_PERFMON_SHIFT, 4, 0xf),
+	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_DFR0_PERFMON_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_MPROFDBG_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_MMAPTRC_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_COPTRC_SHIFT, 4, 0),
@@ -549,7 +586,7 @@
  * Common ftr bits for a 32bit register with all hidden, strict
  * attributes, with 4bit feature fields and a default safe value of
  * 0. Covers the following 32bit registers:
- * id_isar[1-4], id_mmfr[1-3], id_pfr1, mvfr[0-1]
+ * id_isar[1-3], id_mmfr[1-3]
  */
 static const struct arm64_ftr_bits ftr_generic_32bits[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, 28, 4, 0),
@@ -573,15 +610,19 @@
 	ARM64_FTR_END,
 };
 
-#define ARM64_FTR_REG_OVERRIDE(id, table, ovr) {		\
+#define __ARM64_FTR_REG_OVERRIDE(id_str, id, table, ovr) {	\
 		.sys_id = id,					\
 		.reg = 	&(struct arm64_ftr_reg){		\
-			.name = #id,				\
+			.name = id_str,				\
 			.override = (ovr),			\
 			.ftr_bits = &((table)[0]),		\
 	}}
 
-#define ARM64_FTR_REG(id, table) ARM64_FTR_REG_OVERRIDE(id, table, &no_override)
+#define ARM64_FTR_REG_OVERRIDE(id, table, ovr)	\
+	__ARM64_FTR_REG_OVERRIDE(#id, id, table, ovr)
+
+#define ARM64_FTR_REG(id, table)		\
+	__ARM64_FTR_REG_OVERRIDE(#id, id, table, &no_override)
 
 struct arm64_ftr_override __ro_after_init id_aa64mmfr1_override;
 struct arm64_ftr_override __ro_after_init id_aa64pfr1_override;
@@ -612,8 +653,8 @@
 	ARM64_FTR_REG(SYS_ID_ISAR6_EL1, ftr_id_isar6),
 
 	/* Op1 = 0, CRn = 0, CRm = 3 */
-	ARM64_FTR_REG(SYS_MVFR0_EL1, ftr_generic_32bits),
-	ARM64_FTR_REG(SYS_MVFR1_EL1, ftr_generic_32bits),
+	ARM64_FTR_REG(SYS_MVFR0_EL1, ftr_mvfr0),
+	ARM64_FTR_REG(SYS_MVFR1_EL1, ftr_mvfr1),
 	ARM64_FTR_REG(SYS_MVFR2_EL1, ftr_mvfr2),
 	ARM64_FTR_REG(SYS_ID_PFR2_EL1, ftr_id_pfr2),
 	ARM64_FTR_REG(SYS_ID_DFR1_EL1, ftr_id_dfr1),
@@ -633,6 +674,7 @@
 	ARM64_FTR_REG(SYS_ID_AA64ISAR0_EL1, ftr_id_aa64isar0),
 	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64ISAR1_EL1, ftr_id_aa64isar1,
 			       &id_aa64isar1_override),
+	ARM64_FTR_REG(SYS_ID_AA64ISAR2_EL1, ftr_id_aa64isar2),
 
 	/* Op1 = 0, CRn = 0, CRm = 7 */
 	ARM64_FTR_REG(SYS_ID_AA64MMFR0_EL1, ftr_id_aa64mmfr0),
@@ -929,6 +971,7 @@
 	init_cpu_ftr_reg(SYS_ID_AA64DFR1_EL1, info->reg_id_aa64dfr1);
 	init_cpu_ftr_reg(SYS_ID_AA64ISAR0_EL1, info->reg_id_aa64isar0);
 	init_cpu_ftr_reg(SYS_ID_AA64ISAR1_EL1, info->reg_id_aa64isar1);
+	init_cpu_ftr_reg(SYS_ID_AA64ISAR2_EL1, info->reg_id_aa64isar2);
 	init_cpu_ftr_reg(SYS_ID_AA64MMFR0_EL1, info->reg_id_aa64mmfr0);
 	init_cpu_ftr_reg(SYS_ID_AA64MMFR1_EL1, info->reg_id_aa64mmfr1);
 	init_cpu_ftr_reg(SYS_ID_AA64MMFR2_EL1, info->reg_id_aa64mmfr2);
@@ -1147,6 +1190,8 @@
 				      info->reg_id_aa64isar0, boot->reg_id_aa64isar0);
 	taint |= check_update_ftr_reg(SYS_ID_AA64ISAR1_EL1, cpu,
 				      info->reg_id_aa64isar1, boot->reg_id_aa64isar1);
+	taint |= check_update_ftr_reg(SYS_ID_AA64ISAR2_EL1, cpu,
+				      info->reg_id_aa64isar2, boot->reg_id_aa64isar2);
 
 	/*
 	 * Differing PARange support is fine as long as all peripherals and
@@ -1268,6 +1313,7 @@
 	read_sysreg_case(SYS_ID_AA64MMFR2_EL1);
 	read_sysreg_case(SYS_ID_AA64ISAR0_EL1);
 	read_sysreg_case(SYS_ID_AA64ISAR1_EL1);
+	read_sysreg_case(SYS_ID_AA64ISAR2_EL1);
 
 	read_sysreg_case(SYS_CNTFRQ_EL0);
 	read_sysreg_case(SYS_CTR_EL0);
@@ -1297,17 +1343,39 @@
 	return val >= entry->min_field_value;
 }
 
-static bool
-has_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope)
+static u64
+read_scoped_sysreg(const struct arm64_cpu_capabilities *entry, int scope)
 {
-	u64 val;
-
 	WARN_ON(scope == SCOPE_LOCAL_CPU && preemptible());
 	if (scope == SCOPE_SYSTEM)
-		val = read_sanitised_ftr_reg(entry->sys_reg);
+		return read_sanitised_ftr_reg(entry->sys_reg);
 	else
-		val = __read_sysreg_by_encoding(entry->sys_reg);
+		return __read_sysreg_by_encoding(entry->sys_reg);
+}
+
+static bool
+has_user_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope)
+{
+	int mask;
+	struct arm64_ftr_reg *regp;
+	u64 val = read_scoped_sysreg(entry, scope);
+
+	regp = get_arm64_ftr_reg(entry->sys_reg);
+	if (!regp)
+		return false;
+
+	mask = cpuid_feature_extract_unsigned_field(regp->user_mask,
+						    entry->field_pos);
+	if (!mask)
+		return false;
+
+	return feature_matches(val, entry);
+}
 
+static bool
+has_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope)
+{
+	u64 val = read_scoped_sysreg(entry, scope);
 	return feature_matches(val, entry);
 }
 
@@ -1575,6 +1643,12 @@
 
 	int cpu = smp_processor_id();
 
+	if (__this_cpu_read(this_cpu_vector) == vectors) {
+		const char *v = arm64_get_bp_hardening_vector(EL1_VECTOR_KPTI);
+
+		__this_cpu_write(this_cpu_vector, v);
+	}
+
 	/*
 	 * We don't need to rewrite the page-tables if either we've done
 	 * it already or we have KASLR enabled and therefore have not
@@ -1709,7 +1783,10 @@
 		pr_info("detected CPU%d: Activity Monitors Unit (AMU)\n",
 			smp_processor_id());
 		cpumask_set_cpu(smp_processor_id(), &amu_cpus);
-		update_freq_counters_refs();
+
+		/* 0 reference values signal broken/disabled counters */
+		if (!this_cpu_has_cap(ARM64_WORKAROUND_2457168))
+			update_freq_counters_refs();
 	}
 }
 
@@ -1872,7 +1949,8 @@
 static void cpu_enable_mte(struct arm64_cpu_capabilities const *cap)
 {
 	sysreg_clear_set(sctlr_el1, 0, SCTLR_ELx_ATA | SCTLR_EL1_ATA0);
-	isb();
+
+	mte_cpu_setup();
 
 	/*
 	 * Clear the tags in the zero page. This needs to be done via the
@@ -1885,6 +1963,25 @@
 }
 #endif /* CONFIG_ARM64_MTE */
 
+static void user_feature_fixup(void)
+{
+	if (cpus_have_cap(ARM64_WORKAROUND_SPECULATIVE_SSBS)) {
+		struct arm64_ftr_reg *regp;
+
+		regp = get_arm64_ftr_reg(SYS_ID_AA64PFR1_EL1);
+		if (regp)
+			regp->user_mask &= ~GENMASK(7, 4); /* SSBS */
+	}
+}
+
+static void elf_hwcap_fixup(void)
+{
+#ifdef CONFIG_ARM64_ERRATUM_1742098
+	if (cpus_have_const_cap(ARM64_WORKAROUND_1742098))
+		compat_elf_hwcap2 &= ~COMPAT_HWCAP2_AES;
+#endif /* ARM64_ERRATUM_1742098 */
+}
+
 #ifdef CONFIG_KVM
 static bool is_kvm_protected_mode(const struct arm64_cpu_capabilities *entry, int __unused)
 {
@@ -2336,7 +2433,7 @@
 };
 
 #define HWCAP_CPUID_MATCH(reg, field, s, min_value)				\
-		.matches = has_cpuid_feature,					\
+		.matches = has_user_cpuid_feature,				\
 		.sys_reg = reg,							\
 		.field_pos = field,						\
 		.sign = s,							\
@@ -2451,6 +2548,9 @@
 #ifdef CONFIG_ARM64_MTE
 	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_MTE_SHIFT, FTR_UNSIGNED, ID_AA64PFR1_MTE, CAP_HWCAP, KERNEL_HWCAP_MTE),
 #endif /* CONFIG_ARM64_MTE */
+	HWCAP_CAP(SYS_ID_AA64MMFR0_EL1, ID_AA64MMFR0_ECV_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ECV),
+	HWCAP_CAP(SYS_ID_AA64MMFR1_EL1, ID_AA64MMFR1_AFP_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_AFP),
+	HWCAP_CAP(SYS_ID_AA64ISAR2_EL1, ID_AA64ISAR2_RPRES_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_RPRES),
 	{},
 };
 
@@ -2907,10 +3007,13 @@
 	u32 cwg;
 
 	setup_system_capabilities();
+	user_feature_fixup();
 	setup_elf_hwcaps(arm64_elf_hwcaps);
 
-	if (system_supports_32bit_el0())
+	if (system_supports_32bit_el0()) {
 		setup_elf_hwcaps(compat_elf_hwcaps);
+		elf_hwcap_fixup();
+	}
 
 	if (system_uses_ttbr0_pan())
 		pr_info("emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching\n");
@@ -2962,6 +3065,7 @@
 							 cpu_active_mask);
 	get_cpu_device(lucky_winner)->offline_disabled = true;
 	setup_elf_hwcaps(compat_elf_hwcaps);
+	elf_hwcap_fixup();
 	pr_info("Asymmetric 32-bit EL0 support detected on CPU %u; CPU hot-unplug disabled on CPU %u\n",
 		cpu, lucky_winner);
 	return 0;
@@ -2988,7 +3092,7 @@
 
 /*
  * We emulate only the following system register space.
- * Op0 = 0x3, CRn = 0x0, Op1 = 0x0, CRm = [0, 4 - 7]
+ * Op0 = 0x3, CRn = 0x0, Op1 = 0x0, CRm = [0, 2 - 7]
  * See Table C5-6 System instruction encodings for System register accesses,
  * ARMv8 ARM(ARM DDI 0487A.f) for more details.
  */
@@ -2998,7 +3102,7 @@
 		sys_reg_CRn(id) == 0x0 &&
 		sys_reg_Op1(id) == 0x0 &&
 		(sys_reg_CRm(id) == 0 ||
-		 ((sys_reg_CRm(id) >= 4) && (sys_reg_CRm(id) <= 7))));
+		 ((sys_reg_CRm(id) >= 2) && (sys_reg_CRm(id) <= 7))));
 }
 
 /*
@@ -3060,35 +3164,22 @@
 	return rc;
 }
 
-static int emulate_mrs(struct pt_regs *regs, u32 insn)
+bool try_emulate_mrs(struct pt_regs *regs, u32 insn)
 {
 	u32 sys_reg, rt;
 
+	if (compat_user_mode(regs) || !aarch64_insn_is_mrs(insn))
+		return false;
+
 	/*
 	 * sys_reg values are defined as used in mrs/msr instruction.
 	 * shift the imm value to get the encoding.
 	 */
 	sys_reg = (u32)aarch64_insn_decode_immediate(AARCH64_INSN_IMM_16, insn) << 5;
 	rt = aarch64_insn_decode_register(AARCH64_INSN_REGTYPE_RT, insn);
-	return do_emulate_mrs(regs, sys_reg, rt);
+	return do_emulate_mrs(regs, sys_reg, rt) == 0;
 }
 
-static struct undef_hook mrs_hook = {
-	.instr_mask = 0xffff0000,
-	.instr_val  = 0xd5380000,
-	.pstate_mask = PSR_AA32_MODE_MASK,
-	.pstate_val = PSR_MODE_EL0t,
-	.fn = emulate_mrs,
-};
-
-static int __init enable_mrs_emulation(void)
-{
-	register_undef_hook(&mrs_hook);
-	return 0;
-}
-
-core_initcall(enable_mrs_emulation);
-
 enum mitigation_state arm64_get_meltdown_state(void)
 {
 	if (__meltdown_safe)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/cpuidle.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/cpuidle.c
@@ -54,6 +54,9 @@
 	struct acpi_lpi_state *lpi;
 	struct acpi_processor *pr = per_cpu(processors, cpu);
 
+	if (unlikely(!pr || !pr->flags.has_lpi))
+		return -EINVAL;
+
 	/*
 	 * If the PSCI cpu_suspend function hook has not been initialized
 	 * idle states must not be enabled, so bail out
@@ -61,9 +64,6 @@
 	if (!psci_ops.cpu_suspend)
 		return -EOPNOTSUPP;
 
-	if (unlikely(!pr || !pr->flags.has_lpi))
-		return -EINVAL;
-
 	count = pr->power.count - 1;
 	if (count <= 0)
 		return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/cpuinfo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/cpuinfo.c
@@ -94,6 +94,9 @@
 	[KERNEL_HWCAP_RNG]		= "rng",
 	[KERNEL_HWCAP_BTI]		= "bti",
 	[KERNEL_HWCAP_MTE]		= "mte",
+	[KERNEL_HWCAP_ECV]		= "ecv",
+	[KERNEL_HWCAP_AFP]		= "afp",
+	[KERNEL_HWCAP_RPRES]		= "rpres",
 };
 
 #ifdef CONFIG_COMPAT
@@ -390,6 +393,7 @@
 	info->reg_id_aa64dfr1 = read_cpuid(ID_AA64DFR1_EL1);
 	info->reg_id_aa64isar0 = read_cpuid(ID_AA64ISAR0_EL1);
 	info->reg_id_aa64isar1 = read_cpuid(ID_AA64ISAR1_EL1);
+	info->reg_id_aa64isar2 = read_cpuid(ID_AA64ISAR2_EL1);
 	info->reg_id_aa64mmfr0 = read_cpuid(ID_AA64MMFR0_EL1);
 	info->reg_id_aa64mmfr1 = read_cpuid(ID_AA64MMFR1_EL1);
 	info->reg_id_aa64mmfr2 = read_cpuid(ID_AA64MMFR2_EL1);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/debug-monitors.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/debug-monitors.c
@@ -202,7 +202,7 @@
  * So we call all the registered handlers, until the right handler is
  * found which returns zero.
  */
-static int call_step_hook(struct pt_regs *regs, unsigned int esr)
+static int call_step_hook(struct pt_regs *regs, unsigned long esr)
 {
 	struct step_hook *hook;
 	struct list_head *list;
@@ -238,7 +238,7 @@
 			      "User debug trap");
 }
 
-static int single_step_handler(unsigned long unused, unsigned int esr,
+static int single_step_handler(unsigned long unused, unsigned long esr,
 			       struct pt_regs *regs)
 {
 	bool handler_found = false;
@@ -299,11 +299,11 @@
 	unregister_debug_hook(&hook->node);
 }
 
-static int call_break_hook(struct pt_regs *regs, unsigned int esr)
+static int call_break_hook(struct pt_regs *regs, unsigned long esr)
 {
 	struct break_hook *hook;
 	struct list_head *list;
-	int (*fn)(struct pt_regs *regs, unsigned int esr) = NULL;
+	int (*fn)(struct pt_regs *regs, unsigned long esr) = NULL;
 
 	list = user_mode(regs) ? &user_break_hook : &kernel_break_hook;
 
@@ -312,7 +312,7 @@
 	 * entirely not preemptible, and we can use rcu list safely here.
 	 */
 	list_for_each_entry_rcu(hook, list, node) {
-		unsigned int comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
+		unsigned long comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
 
 		if ((comment & ~hook->mask) == hook->imm)
 			fn = hook->fn;
@@ -322,7 +322,7 @@
 }
 NOKPROBE_SYMBOL(call_break_hook);
 
-static int brk_handler(unsigned long unused, unsigned int esr,
+static int brk_handler(unsigned long unused, unsigned long esr,
 		       struct pt_regs *regs)
 {
 	if (call_break_hook(regs, esr) == DBG_HOOK_HANDLED)
@@ -438,6 +438,11 @@
 }
 NOKPROBE_SYMBOL(kernel_active_single_step);
 
+void kernel_rewind_single_step(struct pt_regs *regs)
+{
+	set_regs_spsr_ss(regs);
+}
+
 /* ptrace API */
 void user_enable_single_step(struct task_struct *task)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/efi-rt-wrapper.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/efi-rt-wrapper.S
@@ -4,9 +4,10 @@
  */
 
 #include <linux/linkage.h>
+#include <asm/assembler.h>
 
 SYM_FUNC_START(__efi_rt_asm_wrapper)
-	stp	x29, x30, [sp, #-32]!
+	stp	x29, x30, [sp, #-112]!
 	mov	x29, sp
 
 	/*
@@ -17,6 +18,22 @@
 	stp	x1, x18, [sp, #16]
 
 	/*
+	 * Preserve all callee saved registers and preserve the stack pointer
+	 * value at the base of the EFI runtime stack so we can recover from
+	 * synchronous exceptions occurring while executing the firmware
+	 * routines.
+	 */
+	stp	x19, x20, [sp, #32]
+	stp	x21, x22, [sp, #48]
+	stp	x23, x24, [sp, #64]
+	stp	x25, x26, [sp, #80]
+	stp	x27, x28, [sp, #96]
+
+	ldr_l	x16, efi_rt_stack_top
+	mov	sp, x16
+	stp	x18, x29, [sp, #-16]!
+
+	/*
 	 * We are lucky enough that no EFI runtime services take more than
 	 * 5 arguments, so all are passed in registers rather than via the
 	 * stack.
@@ -29,9 +46,10 @@
 	mov	x4, x6
 	blr	x8
 
+	mov	sp, x29
 	ldp	x1, x2, [sp, #16]
 	cmp	x2, x18
-	ldp	x29, x30, [sp], #32
+	ldp	x29, x30, [sp], #112
 	b.ne	0f
 	ret
 0:
@@ -42,6 +60,22 @@
 	 * called with preemption disabled and a separate shadow stack is used
 	 * for interrupts.
 	 */
-	mov	x18, x2
+#ifdef CONFIG_SHADOW_CALL_STACK
+	ldr_l	x18, efi_rt_stack_top
+	ldr	x18, [x18, #-16]
+#endif
+
 	b	efi_handle_corrupted_x18	// tail call
 SYM_FUNC_END(__efi_rt_asm_wrapper)
+
+SYM_CODE_START(__efi_rt_asm_recover)
+	mov	sp, x30
+
+	ldp	x19, x20, [sp, #32]
+	ldp	x21, x22, [sp, #48]
+	ldp	x23, x24, [sp, #64]
+	ldp	x25, x26, [sp, #80]
+	ldp	x27, x28, [sp, #96]
+	ldp	x29, x30, [sp], #112
+	ret
+SYM_CODE_END(__efi_rt_asm_recover)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/efi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/efi.c
@@ -12,6 +12,14 @@
 
 #include <asm/efi.h>
 
+static bool region_is_misaligned(const efi_memory_desc_t *md)
+{
+	if (PAGE_SIZE == EFI_PAGE_SIZE)
+		return false;
+	return !PAGE_ALIGNED(md->phys_addr) ||
+	       !PAGE_ALIGNED(md->num_pages << EFI_PAGE_SHIFT);
+}
+
 /*
  * Only regions of type EFI_RUNTIME_SERVICES_CODE need to be
  * executable, everything else can be mapped with the XN bits
@@ -25,14 +33,22 @@
 	if (type == EFI_MEMORY_MAPPED_IO)
 		return PROT_DEVICE_nGnRE;
 
-	if (WARN_ONCE(!PAGE_ALIGNED(md->phys_addr),
-		      "UEFI Runtime regions are not aligned to 64 KB -- buggy firmware?"))
+	if (region_is_misaligned(md)) {
+		static bool __initdata code_is_misaligned;
+
 		/*
-		 * If the region is not aligned to the page size of the OS, we
-		 * can not use strict permissions, since that would also affect
-		 * the mapping attributes of the adjacent regions.
+		 * Regions that are not aligned to the OS page size cannot be
+		 * mapped with strict permissions, as those might interfere
+		 * with the permissions that are needed by the adjacent
+		 * region's mapping. However, if we haven't encountered any
+		 * misaligned runtime code regions so far, we can safely use
+		 * non-executable permissions for non-code regions.
 		 */
-		return pgprot_val(PAGE_KERNEL_EXEC);
+		code_is_misaligned |= (type == EFI_RUNTIME_SERVICES_CODE);
+
+		return code_is_misaligned ? pgprot_val(PAGE_KERNEL_EXEC)
+					  : pgprot_val(PAGE_KERNEL);
+	}
 
 	/* R-- */
 	if ((attr & (EFI_MEMORY_XP | EFI_MEMORY_RO)) ==
@@ -63,19 +79,16 @@
 	bool page_mappings_only = (md->type == EFI_RUNTIME_SERVICES_CODE ||
 				   md->type == EFI_RUNTIME_SERVICES_DATA);
 
-	if (!PAGE_ALIGNED(md->phys_addr) ||
-	    !PAGE_ALIGNED(md->num_pages << EFI_PAGE_SHIFT)) {
-		/*
-		 * If the end address of this region is not aligned to page
-		 * size, the mapping is rounded up, and may end up sharing a
-		 * page frame with the next UEFI memory region. If we create
-		 * a block entry now, we may need to split it again when mapping
-		 * the next region, and support for that is going to be removed
-		 * from the MMU routines. So avoid block mappings altogether in
-		 * that case.
-		 */
+	/*
+	 * If this region is not aligned to the page size used by the OS, the
+	 * mapping will be rounded outwards, and may end up sharing a page
+	 * frame with an adjacent runtime memory region. Given that the page
+	 * table descriptor covering the shared page will be rewritten when the
+	 * adjacent region gets mapped, we must avoid block mappings here so we
+	 * don't have to worry about splitting them when that happens.
+	 */
+	if (region_is_misaligned(md))
 		page_mappings_only = true;
-	}
 
 	create_pgd_mapping(mm, md->phys_addr, md->virt_addr,
 			   md->num_pages << EFI_PAGE_SHIFT,
@@ -102,6 +115,9 @@
 	BUG_ON(md->type != EFI_RUNTIME_SERVICES_CODE &&
 	       md->type != EFI_RUNTIME_SERVICES_DATA);
 
+	if (region_is_misaligned(md))
+		return 0;
+
 	/*
 	 * Calling apply_to_page_range() is only safe on regions that are
 	 * guaranteed to be mapped down to pages. Since we are only called
@@ -128,3 +144,52 @@
 	pr_err_ratelimited(FW_BUG "register x18 corrupted by EFI %s\n", f);
 	return s;
 }
+
+DEFINE_RAW_SPINLOCK(efi_rt_lock);
+
+asmlinkage u64 *efi_rt_stack_top __ro_after_init;
+
+asmlinkage efi_status_t __efi_rt_asm_recover(void);
+
+bool efi_runtime_fixup_exception(struct pt_regs *regs, const char *msg)
+{
+	 /* Check whether the exception occurred while running the firmware */
+	if (current_work() != &efi_rts_work.work || regs->pc >= TASK_SIZE_64)
+		return false;
+
+	pr_err(FW_BUG "Unable to handle %s in EFI runtime service\n", msg);
+	add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK);
+	clear_bit(EFI_RUNTIME_SERVICES, &efi.flags);
+
+	regs->regs[0]	= EFI_ABORTED;
+	regs->regs[30]	= efi_rt_stack_top[-1];
+	regs->pc	= (u64)__efi_rt_asm_recover;
+
+	if (IS_ENABLED(CONFIG_SHADOW_CALL_STACK))
+		regs->regs[18] = efi_rt_stack_top[-2];
+
+	return true;
+}
+
+/* EFI requires 8 KiB of stack space for runtime services */
+static_assert(THREAD_SIZE >= SZ_8K);
+
+static int __init arm64_efi_rt_init(void)
+{
+	void *p;
+
+	if (!efi_enabled(EFI_RUNTIME_SERVICES))
+		return 0;
+
+	p = __vmalloc_node(THREAD_SIZE, THREAD_ALIGN, GFP_KERNEL,
+			   NUMA_NO_NODE, &&l);
+l:	if (!p) {
+		pr_warn("Failed to allocate EFI runtime stack\n");
+		clear_bit(EFI_RUNTIME_SERVICES, &efi.flags);
+		return -ENOMEM;
+	}
+
+	efi_rt_stack_top = p + THREAD_SIZE;
+	return 0;
+}
+core_initcall(arm64_efi_rt_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/entry-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/entry-common.c
@@ -72,7 +72,7 @@
 	if (interrupts_enabled(regs)) {
 		if (regs->exit_rcu) {
 			trace_hardirqs_on_prepare();
-			lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+			lockdep_hardirqs_on_prepare();
 			rcu_irq_exit();
 			lockdep_hardirqs_on(CALLER_ADDR0);
 			return;
@@ -117,7 +117,7 @@
 static __always_inline void __exit_to_user_mode(void)
 {
 	trace_hardirqs_on_prepare();
-	lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+	lockdep_hardirqs_on_prepare();
 	user_enter_irqoff();
 	lockdep_hardirqs_on(CALLER_ADDR0);
 }
@@ -175,7 +175,7 @@
 	ftrace_nmi_exit();
 	if (restore) {
 		trace_hardirqs_on_prepare();
-		lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+		lockdep_hardirqs_on_prepare();
 	}
 
 	rcu_nmi_exit();
@@ -211,7 +211,7 @@
 
 	if (restore) {
 		trace_hardirqs_on_prepare();
-		lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+		lockdep_hardirqs_on_prepare();
 	}
 
 	rcu_nmi_exit();
@@ -273,13 +273,13 @@
 extern void (*handle_arch_fiq)(struct pt_regs *);
 
 static void noinstr __panic_unhandled(struct pt_regs *regs, const char *vector,
-				      unsigned int esr)
+				      unsigned long esr)
 {
 	arm64_enter_nmi(regs);
 
 	console_verbose();
 
-	pr_crit("Unhandled %s exception on CPU%d, ESR 0x%08x -- %s\n",
+	pr_crit("Unhandled %s exception on CPU%d, ESR 0x%016lx -- %s\n",
 		vector, smp_processor_id(), esr,
 		esr_get_class_string(esr));
 
@@ -320,7 +320,8 @@
 	__this_cpu_write(__in_cortex_a76_erratum_1463225_wa, 0);
 }
 
-static bool cortex_a76_erratum_1463225_debug_handler(struct pt_regs *regs)
+static __always_inline bool
+cortex_a76_erratum_1463225_debug_handler(struct pt_regs *regs)
 {
 	if (!__this_cpu_read(__in_cortex_a76_erratum_1463225_wa))
 		return false;
@@ -370,11 +371,20 @@
 	exit_to_kernel_mode(regs);
 }
 
-static void noinstr el1_undef(struct pt_regs *regs)
+static void noinstr el1_undef(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_kernel_mode(regs);
 	local_daif_inherit(regs);
-	do_undefinstr(regs);
+	do_el1_undef(regs, esr);
+	local_daif_mask();
+	exit_to_kernel_mode(regs);
+}
+
+static void noinstr el1_bti(struct pt_regs *regs, unsigned long esr)
+{
+	enter_from_kernel_mode(regs);
+	local_daif_inherit(regs);
+	do_el1_bti(regs, esr);
 	local_daif_mask();
 	exit_to_kernel_mode(regs);
 }
@@ -393,7 +403,7 @@
 {
 	enter_from_kernel_mode(regs);
 	local_daif_inherit(regs);
-	do_ptrauth_fault(regs, esr);
+	do_el1_fpac(regs, esr);
 	local_daif_mask();
 	exit_to_kernel_mode(regs);
 }
@@ -416,7 +426,10 @@
 		break;
 	case ESR_ELx_EC_SYS64:
 	case ESR_ELx_EC_UNKNOWN:
-		el1_undef(regs);
+		el1_undef(regs, esr);
+		break;
+	case ESR_ELx_EC_BTI:
+		el1_bti(regs, esr);
 		break;
 	case ESR_ELx_EC_BREAKPT_CUR:
 	case ESR_ELx_EC_SOFTSTP_CUR:
@@ -528,7 +541,7 @@
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_sysinstr(esr, regs);
+	do_el0_sys(esr, regs);
 	exit_to_user_mode(regs);
 }
 
@@ -553,11 +566,11 @@
 	exit_to_user_mode(regs);
 }
 
-static void noinstr el0_undef(struct pt_regs *regs)
+static void noinstr el0_undef(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_undefinstr(regs);
+	do_el0_undef(regs, esr);
 	exit_to_user_mode(regs);
 }
 
@@ -565,7 +578,7 @@
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_bti(regs);
+	do_el0_bti(regs);
 	exit_to_user_mode(regs);
 }
 
@@ -600,7 +613,7 @@
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_ptrauth_fault(regs, esr);
+	do_el0_fpac(regs, esr);
 	exit_to_user_mode(regs);
 }
 
@@ -638,7 +651,7 @@
 		el0_pc(regs, esr);
 		break;
 	case ESR_ELx_EC_UNKNOWN:
-		el0_undef(regs);
+		el0_undef(regs, esr);
 		break;
 	case ESR_ELx_EC_BTI:
 		el0_bti(regs);
@@ -715,7 +728,7 @@
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_cp15instr(esr, regs);
+	do_el0_cp15(esr, regs);
 	exit_to_user_mode(regs);
 }
 
@@ -754,7 +767,7 @@
 	case ESR_ELx_EC_CP14_MR:
 	case ESR_ELx_EC_CP14_LS:
 	case ESR_ELx_EC_CP14_64:
-		el0_undef(regs);
+		el0_undef(regs, esr);
 		break;
 	case ESR_ELx_EC_CP15_32:
 	case ESR_ELx_EC_CP15_64:
@@ -795,7 +808,7 @@
 #ifdef CONFIG_VMAP_STACK
 asmlinkage void noinstr handle_bad_stack(struct pt_regs *regs)
 {
-	unsigned int esr = read_sysreg(esr_el1);
+	unsigned long esr = read_sysreg(esr_el1);
 	unsigned long far = read_sysreg(far_el1);
 
 	arm64_enter_nmi(regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/entry-ftrace.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/entry-ftrace.S
@@ -77,11 +77,17 @@
 	.endm
 
 SYM_CODE_START(ftrace_regs_caller)
+#ifdef BTI_C
+	BTI_C
+#endif
 	ftrace_regs_entry	1
 	b	ftrace_common
 SYM_CODE_END(ftrace_regs_caller)
 
 SYM_CODE_START(ftrace_caller)
+#ifdef BTI_C
+	BTI_C
+#endif
 	ftrace_regs_entry	0
 	b	ftrace_common
 SYM_CODE_END(ftrace_caller)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/entry.S
@@ -37,18 +37,21 @@
 
 	.macro kernel_ventry, el:req, ht:req, regsize:req, label:req
 	.align 7
-#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+.Lventry_start\@:
 	.if	\el == 0
-alternative_if ARM64_UNMAP_KERNEL_AT_EL0
+	/*
+	 * This must be the first instruction of the EL0 vector entries. It is
+	 * skipped by the trampoline vectors, to trigger the cleanup.
+	 */
+	b	.Lskip_tramp_vectors_cleanup\@
 	.if	\regsize == 64
 	mrs	x30, tpidrro_el0
 	msr	tpidrro_el0, xzr
 	.else
 	mov	x30, xzr
 	.endif
-alternative_else_nop_endif
+.Lskip_tramp_vectors_cleanup\@:
 	.endif
-#endif
 
 	sub	sp, sp, #PT_REGS_SIZE
 #ifdef CONFIG_VMAP_STACK
@@ -95,11 +98,15 @@
 	mrs	x0, tpidrro_el0
 #endif
 	b	el\el\ht\()_\regsize\()_\label
+.org .Lventry_start\@ + 128	// Did we overflow the ventry slot?
 	.endm
 
-	.macro tramp_alias, dst, sym
+	.macro tramp_alias, dst, sym, tmp
 	mov_q	\dst, TRAMP_VALIAS
-	add	\dst, \dst, #(\sym - .entry.tramp.text)
+	adr_l	\tmp, \sym
+	add	\dst, \dst, \tmp
+	adr_l	\tmp, .entry.tramp.text
+	sub	\dst, \dst, \tmp
 	.endm
 
 	/*
@@ -116,7 +123,7 @@
 	tbnz	\tmp2, #TIF_SSBD, .L__asm_ssbd_skip\@
 	mov	w0, #ARM_SMCCC_ARCH_WORKAROUND_2
 	mov	w1, #\state
-alternative_cb	spectre_v4_patch_fw_mitigation_conduit
+alternative_cb	smccc_patch_fw_mitigation_conduit
 	nop					// Patched to SMC/HVC #0
 alternative_cb_end
 .L__asm_ssbd_skip\@:
@@ -265,7 +272,7 @@
 alternative_else_nop_endif
 1:
 
-	scs_load tsk
+	scs_load_current
 	.else
 	add	x21, sp, #PT_REGS_SIZE
 	get_current_task tsk
@@ -413,21 +420,26 @@
 	ldp	x24, x25, [sp, #16 * 12]
 	ldp	x26, x27, [sp, #16 * 13]
 	ldp	x28, x29, [sp, #16 * 14]
-	ldr	lr, [sp, #S_LR]
-	add	sp, sp, #PT_REGS_SIZE		// restore sp
 
 	.if	\el == 0
-alternative_insn eret, nop, ARM64_UNMAP_KERNEL_AT_EL0
+alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0
+	ldr	lr, [sp, #S_LR]
+	add	sp, sp, #PT_REGS_SIZE		// restore sp
+	eret
+alternative_else_nop_endif
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 	bne	4f
-	msr	far_el1, x30
-	tramp_alias	x30, tramp_exit_native
+	msr	far_el1, x29
+	tramp_alias	x30, tramp_exit_native, x29
 	br	x30
 4:
-	tramp_alias	x30, tramp_exit_compat
+	tramp_alias	x30, tramp_exit_compat, x29
 	br	x30
 #endif
 	.else
+	ldr	lr, [sp, #S_LR]
+	add	sp, sp, #PT_REGS_SIZE		// restore sp
+
 	/* Ensure any device/NC reads complete */
 	alternative_insn nop, "dmb sy", ARM64_WORKAROUND_1508412
 
@@ -594,12 +606,6 @@
 
 	.popsection				// .entry.text
 
-#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-/*
- * Exception vectors trampoline.
- */
-	.pushsection ".entry.tramp.text", "ax"
-
 	// Move from tramp_pg_dir to swapper_pg_dir
 	.macro tramp_map_kernel, tmp
 	mrs	\tmp, ttbr1_el1
@@ -633,12 +639,47 @@
 	 */
 	.endm
 
-	.macro tramp_ventry, regsize = 64
+	.macro tramp_data_page	dst
+	adr_l	\dst, .entry.tramp.text
+	sub	\dst, \dst, PAGE_SIZE
+	.endm
+
+	.macro tramp_data_read_var	dst, var
+#ifdef CONFIG_RANDOMIZE_BASE
+	tramp_data_page		\dst
+	add	\dst, \dst, #:lo12:__entry_tramp_data_\var
+	ldr	\dst, [\dst]
+#else
+	ldr	\dst, =\var
+#endif
+	.endm
+
+#define BHB_MITIGATION_NONE	0
+#define BHB_MITIGATION_LOOP	1
+#define BHB_MITIGATION_FW	2
+#define BHB_MITIGATION_INSN	3
+
+	.macro tramp_ventry, vector_start, regsize, kpti, bhb
 	.align	7
 1:
 	.if	\regsize == 64
 	msr	tpidrro_el0, x30	// Restored in kernel_ventry
 	.endif
+
+	.if	\bhb == BHB_MITIGATION_LOOP
+	/*
+	 * This sequence must appear before the first indirect branch. i.e. the
+	 * ret out of tramp_ventry. It appears here because x30 is free.
+	 */
+	__mitigate_spectre_bhb_loop	x30
+	.endif // \bhb == BHB_MITIGATION_LOOP
+
+	.if	\bhb == BHB_MITIGATION_INSN
+	clearbhb
+	isb
+	.endif // \bhb == BHB_MITIGATION_INSN
+
+	.if	\kpti == 1
 	/*
 	 * Defend against branch aliasing attacks by pushing a dummy
 	 * entry onto the return stack and using a RET instruction to
@@ -648,46 +689,75 @@
 	b	.
 2:
 	tramp_map_kernel	x30
-#ifdef CONFIG_RANDOMIZE_BASE
-	adr	x30, tramp_vectors + PAGE_SIZE
 alternative_insn isb, nop, ARM64_WORKAROUND_QCOM_FALKOR_E1003
-	ldr	x30, [x30]
-#else
-	ldr	x30, =vectors
-#endif
+	tramp_data_read_var	x30, vectors
 alternative_if_not ARM64_WORKAROUND_CAVIUM_TX2_219_PRFM
-	prfm	plil1strm, [x30, #(1b - tramp_vectors)]
+	prfm	plil1strm, [x30, #(1b - \vector_start)]
 alternative_else_nop_endif
+
 	msr	vbar_el1, x30
-	add	x30, x30, #(1b - tramp_vectors)
 	isb
+	.else
+	ldr	x30, =vectors
+	.endif // \kpti == 1
+
+	.if	\bhb == BHB_MITIGATION_FW
+	/*
+	 * The firmware sequence must appear before the first indirect branch.
+	 * i.e. the ret out of tramp_ventry. But it also needs the stack to be
+	 * mapped to save/restore the registers the SMC clobbers.
+	 */
+	__mitigate_spectre_bhb_fw
+	.endif // \bhb == BHB_MITIGATION_FW
+
+	add	x30, x30, #(1b - \vector_start + 4)
 	ret
+.org 1b + 128	// Did we overflow the ventry slot?
 	.endm
 
 	.macro tramp_exit, regsize = 64
-	adr	x30, tramp_vectors
+	tramp_data_read_var	x30, this_cpu_vector
+	get_this_cpu_offset x29
+	ldr	x30, [x30, x29]
+
 	msr	vbar_el1, x30
-	tramp_unmap_kernel	x30
+	ldr	lr, [sp, #S_LR]
+	tramp_unmap_kernel	x29
 	.if	\regsize == 64
-	mrs	x30, far_el1
+	mrs	x29, far_el1
 	.endif
+	add	sp, sp, #PT_REGS_SIZE		// restore sp
 	eret
 	sb
 	.endm
 
-	.align	11
-SYM_CODE_START_NOALIGN(tramp_vectors)
+	.macro	generate_tramp_vector,	kpti, bhb
+.Lvector_start\@:
 	.space	0x400
 
-	tramp_ventry
-	tramp_ventry
-	tramp_ventry
-	tramp_ventry
-
-	tramp_ventry	32
-	tramp_ventry	32
-	tramp_ventry	32
-	tramp_ventry	32
+	.rept	4
+	tramp_ventry	.Lvector_start\@, 64, \kpti, \bhb
+	.endr
+	.rept	4
+	tramp_ventry	.Lvector_start\@, 32, \kpti, \bhb
+	.endr
+	.endm
+
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+/*
+ * Exception vectors trampoline.
+ * The order must match __bp_harden_el1_vectors and the
+ * arm64_bp_harden_el1_vectors enum.
+ */
+	.pushsection ".entry.tramp.text", "ax"
+	.align	11
+SYM_CODE_START_NOALIGN(tramp_vectors)
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_LOOP
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_FW
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_INSN
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_NONE
 SYM_CODE_END(tramp_vectors)
 
 SYM_CODE_START(tramp_exit_native)
@@ -704,13 +774,57 @@
 	.pushsection ".rodata", "a"
 	.align PAGE_SHIFT
 SYM_DATA_START(__entry_tramp_data_start)
+__entry_tramp_data_vectors:
 	.quad	vectors
+#ifdef CONFIG_ARM_SDE_INTERFACE
+__entry_tramp_data___sdei_asm_handler:
+	.quad	__sdei_asm_handler
+#endif /* CONFIG_ARM_SDE_INTERFACE */
+__entry_tramp_data_this_cpu_vector:
+	.quad	this_cpu_vector
 SYM_DATA_END(__entry_tramp_data_start)
 	.popsection				// .rodata
 #endif /* CONFIG_RANDOMIZE_BASE */
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 /*
+ * Exception vectors for spectre mitigations on entry from EL1 when
+ * kpti is not in use.
+ */
+	.macro generate_el1_vector, bhb
+.Lvector_start\@:
+	kernel_ventry	1, t, 64, sync		// Synchronous EL1t
+	kernel_ventry	1, t, 64, irq		// IRQ EL1t
+	kernel_ventry	1, t, 64, fiq		// FIQ EL1h
+	kernel_ventry	1, t, 64, error		// Error EL1t
+
+	kernel_ventry	1, h, 64, sync		// Synchronous EL1h
+	kernel_ventry	1, h, 64, irq		// IRQ EL1h
+	kernel_ventry	1, h, 64, fiq		// FIQ EL1h
+	kernel_ventry	1, h, 64, error		// Error EL1h
+
+	.rept	4
+	tramp_ventry	.Lvector_start\@, 64, 0, \bhb
+	.endr
+	.rept 4
+	tramp_ventry	.Lvector_start\@, 32, 0, \bhb
+	.endr
+	.endm
+
+/* The order must match tramp_vecs and the arm64_bp_harden_el1_vectors enum. */
+	.pushsection ".entry.text", "ax"
+	.align	11
+SYM_CODE_START(__bp_harden_el1_vectors)
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	generate_el1_vector	bhb=BHB_MITIGATION_LOOP
+	generate_el1_vector	bhb=BHB_MITIGATION_FW
+	generate_el1_vector	bhb=BHB_MITIGATION_INSN
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+SYM_CODE_END(__bp_harden_el1_vectors)
+	.popsection
+
+
+/*
  * Register switch for AArch64. The callee-saved registers need to be saved
  * and restored. On entry:
  *   x0 = previous task_struct (must be preserved across the switch)
@@ -741,7 +855,7 @@
 	msr	sp_el0, x1
 	ptrauth_keys_install_kernel x1, x8, x9, x10
 	scs_save x0
-	scs_load x1
+	scs_load_current
 	ret
 SYM_FUNC_END(cpu_switch_to)
 NOKPROBE(cpu_switch_to)
@@ -769,19 +883,19 @@
  */
 SYM_FUNC_START(call_on_irq_stack)
 #ifdef CONFIG_SHADOW_CALL_STACK
-	stp	scs_sp, xzr, [sp, #-16]!
+	get_current_task x16
+	scs_save x16
 	ldr_this_cpu scs_sp, irq_shadow_call_stack_ptr, x17
 #endif
+
 	/* Create a frame record to save our LR and SP (implicit in FP) */
 	stp	x29, x30, [sp, #-16]!
 	mov	x29, sp
 
 	ldr_this_cpu x16, irq_stack_ptr, x17
-	mov	x15, #IRQ_STACK_SIZE
-	add	x16, x16, x15
 
 	/* Move to the new stack and call the function there */
-	mov	sp, x16
+	add	sp, x16, #IRQ_STACK_SIZE
 	blr	x1
 
 	/*
@@ -790,9 +904,7 @@
 	 */
 	mov	sp, x29
 	ldp	x29, x30, [sp], #16
-#ifdef CONFIG_SHADOW_CALL_STACK
-	ldp	scs_sp, xzr, [sp], #16
-#endif
+	scs_load_current
 	ret
 SYM_FUNC_END(call_on_irq_stack)
 NOKPROBE(call_on_irq_stack)
@@ -835,14 +947,7 @@
 	 * Remember whether to unmap the kernel on exit.
 	 */
 1:	str	x4, [x1, #(SDEI_EVENT_INTREGS + S_SDEI_TTBR1)]
-
-#ifdef CONFIG_RANDOMIZE_BASE
-	adr	x4, tramp_vectors + PAGE_SIZE
-	add	x4, x4, #:lo12:__sdei_asm_trampoline_next_handler
-	ldr	x4, [x4]
-#else
-	ldr	x4, =__sdei_asm_handler
-#endif
+	tramp_data_read_var     x4, __sdei_asm_handler
 	br	x4
 SYM_CODE_END(__sdei_asm_entry_trampoline)
 NOKPROBE(__sdei_asm_entry_trampoline)
@@ -865,13 +970,6 @@
 NOKPROBE(__sdei_asm_exit_trampoline)
 	.ltorg
 .popsection		// .entry.tramp.text
-#ifdef CONFIG_RANDOMIZE_BASE
-.pushsection ".rodata", "a"
-SYM_DATA_START(__sdei_asm_trampoline_next_handler)
-	.quad	__sdei_asm_handler
-SYM_DATA_END(__sdei_asm_trampoline_next_handler)
-.popsection		// .rodata
-#endif /* CONFIG_RANDOMIZE_BASE */
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 /*
@@ -907,9 +1005,13 @@
 
 	mov	x19, x1
 
-#if defined(CONFIG_VMAP_STACK) || defined(CONFIG_SHADOW_CALL_STACK)
+	/* Store the registered-event for crash_smp_send_stop() */
 	ldrb	w4, [x19, #SDEI_EVENT_PRIORITY]
-#endif
+	cbnz	w4, 1f
+	adr_this_cpu dst=x5, sym=sdei_active_normal_event, tmp=x6
+	b	2f
+1:	adr_this_cpu dst=x5, sym=sdei_active_critical_event, tmp=x6
+2:	str	x19, [x5]
 
 #ifdef CONFIG_VMAP_STACK
 	/*
@@ -974,14 +1076,33 @@
 
 	ldr_l	x2, sdei_exit_mode
 
+	/* Clear the registered-event seen by crash_smp_send_stop() */
+	ldrb	w3, [x4, #SDEI_EVENT_PRIORITY]
+	cbnz	w3, 1f
+	adr_this_cpu dst=x5, sym=sdei_active_normal_event, tmp=x6
+	b	2f
+1:	adr_this_cpu dst=x5, sym=sdei_active_critical_event, tmp=x6
+2:	str	xzr, [x5]
+
 alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0
 	sdei_handler_exit exit_mode=x2
 alternative_else_nop_endif
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-	tramp_alias	dst=x5, sym=__sdei_asm_exit_trampoline
+	tramp_alias	dst=x5, sym=__sdei_asm_exit_trampoline, tmp=x3
 	br	x5
 #endif
 SYM_CODE_END(__sdei_asm_handler)
 NOKPROBE(__sdei_asm_handler)
+
+SYM_CODE_START(__sdei_handler_abort)
+	mov_q	x0, SDEI_1_0_FN_SDEI_EVENT_COMPLETE_AND_RESUME
+	adr	x1, 1f
+	ldr_l	x2, sdei_exit_mode
+	sdei_handler_exit exit_mode=x2
+	// exit the handler and jump to the next instruction.
+	// Exit will stomp x0-x17, PSTATE, ELR_ELx, and SPSR_ELx.
+1:	ret
+SYM_CODE_END(__sdei_handler_abort)
+NOKPROBE(__sdei_handler_abort)
 #endif /* CONFIG_ARM_SDE_INTERFACE */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/fpsimd.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/fpsimd.c
@@ -930,7 +930,7 @@
  * would have disabled the SVE access trap for userspace during
  * ret_to_user, making an SVE access trap impossible in that case.
  */
-void do_sve_acc(unsigned int esr, struct pt_regs *regs)
+void do_sve_acc(unsigned long esr, struct pt_regs *regs)
 {
 	/* Even if we chose not to use SVE, the hardware could still trap: */
 	if (unlikely(!system_supports_sve()) || WARN_ON(is_compat_task())) {
@@ -964,6 +964,7 @@
 		fpsimd_bind_task_to_cpu();
 	} else {
 		fpsimd_to_sve(current);
+		fpsimd_flush_task_state(current);
 	}
 
 	put_cpu_fpsimd_context();
@@ -972,7 +973,7 @@
 /*
  * Trapped FP/ASIMD access.
  */
-void do_fpsimd_acc(unsigned int esr, struct pt_regs *regs)
+void do_fpsimd_acc(unsigned long esr, struct pt_regs *regs)
 {
 	/* TODO: implement lazy context saving/restoring */
 	WARN_ON(1);
@@ -981,7 +982,7 @@
 /*
  * Raise a SIGFPE for the current process.
  */
-void do_fpsimd_exc(unsigned int esr, struct pt_regs *regs)
+void do_fpsimd_exc(unsigned long esr, struct pt_regs *regs)
 {
 	unsigned int si_code = FPE_FLTUNK;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/ftrace.c
@@ -78,47 +78,76 @@
 }
 
 /*
- * Turn on the call to ftrace_caller() in instrumented function
+ * Find the address the callsite must branch to in order to reach '*addr'.
+ *
+ * Due to the limited range of 'BL' instructions, modules may be placed too far
+ * away to branch directly and must use a PLT.
+ *
+ * Returns true when '*addr' contains a reachable target address, or has been
+ * modified to contain a PLT address. Returns false otherwise.
  */
-int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
+static bool ftrace_find_callable_addr(struct dyn_ftrace *rec,
+				      struct module *mod,
+				      unsigned long *addr)
 {
 	unsigned long pc = rec->ip;
-	u32 old, new;
-	long offset = (long)pc - (long)addr;
+	long offset = (long)*addr - (long)pc;
+	struct plt_entry *plt;
 
-	if (offset < -SZ_128M || offset >= SZ_128M) {
-		struct module *mod;
-		struct plt_entry *plt;
-
-		if (!IS_ENABLED(CONFIG_ARM64_MODULE_PLTS))
-			return -EINVAL;
-
-		/*
-		 * On kernels that support module PLTs, the offset between the
-		 * branch instruction and its target may legally exceed the
-		 * range of an ordinary relative 'bl' opcode. In this case, we
-		 * need to branch via a trampoline in the module.
-		 *
-		 * NOTE: __module_text_address() must be called with preemption
-		 * disabled, but we can rely on ftrace_lock to ensure that 'mod'
-		 * retains its validity throughout the remainder of this code.
-		 */
+	/*
+	 * When the target is within range of the 'BL' instruction, use 'addr'
+	 * as-is and branch to that directly.
+	 */
+	if (offset >= -SZ_128M && offset < SZ_128M)
+		return true;
+
+	/*
+	 * When the target is outside of the range of a 'BL' instruction, we
+	 * must use a PLT to reach it. We can only place PLTs for modules, and
+	 * only when module PLT support is built-in.
+	 */
+	if (!IS_ENABLED(CONFIG_ARM64_MODULE_PLTS))
+		return false;
+
+	/*
+	 * 'mod' is only set at module load time, but if we end up
+	 * dealing with an out-of-range condition, we can assume it
+	 * is due to a module being loaded far away from the kernel.
+	 *
+	 * NOTE: __module_text_address() must be called with preemption
+	 * disabled, but we can rely on ftrace_lock to ensure that 'mod'
+	 * retains its validity throughout the remainder of this code.
+	 */
+	if (!mod) {
 		preempt_disable();
 		mod = __module_text_address(pc);
 		preempt_enable();
+	}
 
-		if (WARN_ON(!mod))
-			return -EINVAL;
-
-		plt = get_ftrace_plt(mod, addr);
-		if (!plt) {
-			pr_err("ftrace: no module PLT for %ps\n", (void *)addr);
-			return -EINVAL;
-		}
+	if (WARN_ON(!mod))
+		return false;
 
-		addr = (unsigned long)plt;
+	plt = get_ftrace_plt(mod, *addr);
+	if (!plt) {
+		pr_err("ftrace: no module PLT for %ps\n", (void *)*addr);
+		return false;
 	}
 
+	*addr = (unsigned long)plt;
+	return true;
+}
+
+/*
+ * Turn on the call to ftrace_caller() in instrumented function
+ */
+int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
+{
+	unsigned long pc = rec->ip;
+	u32 old, new;
+
+	if (!ftrace_find_callable_addr(rec, NULL, &addr))
+		return -EINVAL;
+
 	old = aarch64_insn_gen_nop();
 	new = aarch64_insn_gen_branch_imm(pc, addr, AARCH64_INSN_BRANCH_LINK);
 
@@ -132,6 +161,11 @@
 	unsigned long pc = rec->ip;
 	u32 old, new;
 
+	if (!ftrace_find_callable_addr(rec, NULL, &old_addr))
+		return -EINVAL;
+	if (!ftrace_find_callable_addr(rec, NULL, &addr))
+		return -EINVAL;
+
 	old = aarch64_insn_gen_branch_imm(pc, old_addr,
 					  AARCH64_INSN_BRANCH_LINK);
 	new = aarch64_insn_gen_branch_imm(pc, addr, AARCH64_INSN_BRANCH_LINK);
@@ -181,54 +215,30 @@
 		    unsigned long addr)
 {
 	unsigned long pc = rec->ip;
-	bool validate = true;
 	u32 old = 0, new;
-	long offset = (long)pc - (long)addr;
-
-	if (offset < -SZ_128M || offset >= SZ_128M) {
-		u32 replaced;
 
-		if (!IS_ENABLED(CONFIG_ARM64_MODULE_PLTS))
-			return -EINVAL;
+	new = aarch64_insn_gen_nop();
 
-		/*
-		 * 'mod' is only set at module load time, but if we end up
-		 * dealing with an out-of-range condition, we can assume it
-		 * is due to a module being loaded far away from the kernel.
-		 */
-		if (!mod) {
-			preempt_disable();
-			mod = __module_text_address(pc);
-			preempt_enable();
-
-			if (WARN_ON(!mod))
-				return -EINVAL;
-		}
-
-		/*
-		 * The instruction we are about to patch may be a branch and
-		 * link instruction that was redirected via a PLT entry. In
-		 * this case, the normal validation will fail, but we can at
-		 * least check that we are dealing with a branch and link
-		 * instruction that points into the right module.
-		 */
-		if (aarch64_insn_read((void *)pc, &replaced))
-			return -EFAULT;
-
-		if (!aarch64_insn_is_bl(replaced) ||
-		    !within_module(pc + aarch64_get_branch_offset(replaced),
-				   mod))
-			return -EINVAL;
-
-		validate = false;
-	} else {
-		old = aarch64_insn_gen_branch_imm(pc, addr,
-						  AARCH64_INSN_BRANCH_LINK);
+	/*
+	 * When using mcount, callsites in modules may have been initalized to
+	 * call an arbitrary module PLT (which redirects to the _mcount stub)
+	 * rather than the ftrace PLT we'll use at runtime (which redirects to
+	 * the ftrace trampoline). We can ignore the old PLT when initializing
+	 * the callsite.
+	 *
+	 * Note: 'mod' is only set at module load time.
+	 */
+	if (!IS_ENABLED(CONFIG_DYNAMIC_FTRACE_WITH_REGS) &&
+	    IS_ENABLED(CONFIG_ARM64_MODULE_PLTS) && mod) {
+		return aarch64_insn_patch_text_nosync((void *)pc, new);
 	}
 
-	new = aarch64_insn_gen_nop();
+	if (!ftrace_find_callable_addr(rec, mod, &addr))
+		return -EINVAL;
+
+	old = aarch64_insn_gen_branch_imm(pc, addr, AARCH64_INSN_BRANCH_LINK);
 
-	return ftrace_modify_code(pc, old, new, validate);
+	return ftrace_modify_code(pc, old, new, true);
 }
 
 void arch_ftrace_update_code(int command)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/head.S
@@ -285,7 +285,7 @@
 	subs	x1, x1, #64
 	b.ne	1b
 
-	mov	x7, SWAPPER_MM_MMUFLAGS
+	mov_q	x7, SWAPPER_MM_MMUFLAGS
 
 	/*
 	 * Create the identity mapping.
@@ -409,7 +409,7 @@
 	stp	xzr, xzr, [sp, #S_STACKFRAME]
 	add	x29, sp, #S_STACKFRAME
 
-	scs_load \tsk
+	scs_load_current
 
 	adr_l	\tmp1, __per_cpu_offset
 	ldr	w\tmp2, [\tsk, #TSK_CPU]
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/hw_breakpoint.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/hw_breakpoint.c
@@ -617,7 +617,7 @@
 /*
  * Debug exception handlers.
  */
-static int breakpoint_handler(unsigned long unused, unsigned int esr,
+static int breakpoint_handler(unsigned long unused, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	int i, step = 0, *kernel_step;
@@ -654,7 +654,7 @@
 		perf_bp_event(bp, regs);
 
 		/* Do we need to handle the stepping? */
-		if (is_default_overflow_handler(bp))
+		if (uses_default_overflow_handler(bp))
 			step = 1;
 unlock:
 		rcu_read_unlock();
@@ -733,7 +733,7 @@
 static int watchpoint_report(struct perf_event *wp, unsigned long addr,
 			     struct pt_regs *regs)
 {
-	int step = is_default_overflow_handler(wp);
+	int step = uses_default_overflow_handler(wp);
 	struct arch_hw_breakpoint *info = counter_arch_bp(wp);
 
 	info->trigger = addr;
@@ -751,7 +751,7 @@
 	return step;
 }
 
-static int watchpoint_handler(unsigned long addr, unsigned int esr,
+static int watchpoint_handler(unsigned long addr, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	int i, step = 0, *kernel_step, access, closest_match = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/image-vars.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/image-vars.h
@@ -66,6 +66,10 @@
 KVM_NVHE_ALIAS(kvm_update_va_mask);
 KVM_NVHE_ALIAS(kvm_get_kimage_voffset);
 KVM_NVHE_ALIAS(kvm_compute_final_ctr_el0);
+KVM_NVHE_ALIAS(spectre_bhb_patch_loop_iter);
+KVM_NVHE_ALIAS(spectre_bhb_patch_loop_mitigation_enable);
+KVM_NVHE_ALIAS(spectre_bhb_patch_wa3);
+KVM_NVHE_ALIAS(spectre_bhb_patch_clearbhb);
 
 /* Global kernel state accessed by nVHE hyp code. */
 KVM_NVHE_ALIAS(kvm_vgic_global_state);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/irq.c
@@ -19,6 +19,7 @@
 #include <linux/kprobes.h>
 #include <linux/scs.h>
 #include <linux/seq_file.h>
+#include <asm/numa.h>
 #include <linux/vmalloc.h>
 #include <asm/daifflags.h>
 #include <asm/vmap_stack.h>
@@ -44,17 +45,17 @@
 
 	for_each_possible_cpu(cpu)
 		per_cpu(irq_shadow_call_stack_ptr, cpu) =
-			scs_alloc(cpu_to_node(cpu));
+			scs_alloc(early_cpu_to_node(cpu));
 }
 
 #ifdef CONFIG_VMAP_STACK
-static void init_irq_stacks(void)
+static void __init init_irq_stacks(void)
 {
 	int cpu;
 	unsigned long *p;
 
 	for_each_possible_cpu(cpu) {
-		p = arch_alloc_vmap_stack(IRQ_STACK_SIZE, cpu_to_node(cpu));
+		p = arch_alloc_vmap_stack(IRQ_STACK_SIZE, early_cpu_to_node(cpu));
 		per_cpu(irq_stack_ptr, cpu) = p;
 	}
 }
@@ -84,7 +85,11 @@
 void (*handle_arch_irq)(struct pt_regs *) __ro_after_init = default_handle_irq;
 void (*handle_arch_fiq)(struct pt_regs *) __ro_after_init = default_handle_fiq;
 
+#ifndef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
 int __init set_handle_irq(void (*handle_irq)(struct pt_regs *))
+#else
+int set_handle_irq(void (*handle_irq)(struct pt_regs *))
+#endif
 {
 	if (handle_arch_irq != default_handle_irq)
 		return -EBUSY;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/kexec_image.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/kexec_image.c
@@ -14,7 +14,6 @@
 #include <linux/kexec.h>
 #include <linux/pe.h>
 #include <linux/string.h>
-#include <linux/verification.h>
 #include <asm/byteorder.h>
 #include <asm/cpufeature.h>
 #include <asm/image.h>
@@ -130,18 +129,10 @@
 	return NULL;
 }
 
-#ifdef CONFIG_KEXEC_IMAGE_VERIFY_SIG
-static int image_verify_sig(const char *kernel, unsigned long kernel_len)
-{
-	return verify_pefile_signature(kernel, kernel_len, NULL,
-				       VERIFYING_KEXEC_PE_SIGNATURE);
-}
-#endif
-
 const struct kexec_file_ops kexec_image_ops = {
 	.probe = image_probe,
 	.load = image_load,
 #ifdef CONFIG_KEXEC_IMAGE_VERIFY_SIG
-	.verify_sig = image_verify_sig,
+	.verify_sig = kexec_kernel_verify_pe_sig,
 #endif
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/kgdb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/kgdb.c
@@ -224,6 +224,8 @@
 		 */
 		if (!kernel_active_single_step())
 			kernel_enable_single_step(linux_regs);
+		else
+			kernel_rewind_single_step(linux_regs);
 		err = 0;
 		break;
 	default:
@@ -232,14 +234,14 @@
 	return err;
 }
 
-static int kgdb_brk_fn(struct pt_regs *regs, unsigned int esr)
+static int kgdb_brk_fn(struct pt_regs *regs, unsigned long esr)
 {
 	kgdb_handle_exception(1, SIGTRAP, 0, regs);
 	return DBG_HOOK_HANDLED;
 }
 NOKPROBE_SYMBOL(kgdb_brk_fn)
 
-static int kgdb_compiled_brk_fn(struct pt_regs *regs, unsigned int esr)
+static int kgdb_compiled_brk_fn(struct pt_regs *regs, unsigned long esr)
 {
 	compiled_break = 1;
 	kgdb_handle_exception(1, SIGTRAP, 0, regs);
@@ -248,7 +250,7 @@
 }
 NOKPROBE_SYMBOL(kgdb_compiled_brk_fn);
 
-static int kgdb_step_brk_fn(struct pt_regs *regs, unsigned int esr)
+static int kgdb_step_brk_fn(struct pt_regs *regs, unsigned long esr)
 {
 	if (!kgdb_single_step)
 		return DBG_HOOK_ERROR;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/machine_kexec.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/machine_kexec.c
@@ -320,8 +320,13 @@
 
 	/* in reserved memory? */
 	addr = __pfn_to_phys(pfn);
-	if ((addr < crashk_res.start) || (crashk_res.end < addr))
-		return false;
+	if ((addr < crashk_res.start) || (crashk_res.end < addr)) {
+		if (!crashk_low_res.end)
+			return false;
+
+		if ((addr < crashk_low_res.start) || (crashk_low_res.end < addr))
+			return false;
+	}
 
 	if (!kexec_crash_image)
 		return true;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/machine_kexec_file.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/machine_kexec_file.c
@@ -65,10 +65,18 @@
 
 	/* Exclude crashkernel region */
 	ret = crash_exclude_mem_range(cmem, crashk_res.start, crashk_res.end);
+	if (ret)
+		goto out;
 
-	if (!ret)
-		ret =  crash_prepare_elf64_headers(cmem, true, addr, sz);
+	if (crashk_low_res.end) {
+		ret = crash_exclude_mem_range(cmem, crashk_low_res.start, crashk_low_res.end);
+		if (ret)
+			goto out;
+	}
+
+	ret = crash_prepare_elf64_headers(cmem, true, addr, sz);
 
+out:
 	kfree(cmem);
 	return ret;
 }
@@ -149,6 +157,7 @@
 					   initrd_len, cmdline, 0);
 	if (!dtb) {
 		pr_err("Preparing for new dtb failed\n");
+		ret = -EINVAL;
 		goto out_err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/module-plts.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/module-plts.c
@@ -7,6 +7,7 @@
 #include <linux/ftrace.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/moduleloader.h>
 #include <linux/sort.h>
 
 static struct plt_entry __get_adrp_add_pair(u64 dst, u64 pc,
@@ -342,7 +343,7 @@
 		if (nents)
 			sort(rels, nents, sizeof(Elf64_Rela), cmp_rela, NULL);
 
-		if (!str_has_prefix(secstrings + dstsec->sh_name, ".init"))
+		if (!module_init_layout_section(secstrings + dstsec->sh_name))
 			core_plts += count_plts(syms, rels, numrels,
 						sechdrs[i].sh_info, dstsec);
 		else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/module.c
@@ -36,7 +36,7 @@
 		module_alloc_end = MODULES_END;
 
 	p = __vmalloc_node_range(size, MODULE_ALIGN, module_alloc_base,
-				module_alloc_end, gfp_mask, PAGE_KERNEL, 0,
+				module_alloc_end, gfp_mask, PAGE_KERNEL, VM_DEFER_KMEMLEAK,
 				NUMA_NO_NODE, __builtin_return_address(0));
 
 	if (!p && IS_ENABLED(CONFIG_ARM64_MODULE_PLTS) &&
@@ -58,7 +58,7 @@
 				PAGE_KERNEL, 0, NUMA_NO_NODE,
 				__builtin_return_address(0));
 
-	if (p && (kasan_module_alloc(p, size) < 0)) {
+	if (p && (kasan_module_alloc(p, size, gfp_mask) < 0)) {
 		vfree(p);
 		return NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/mte.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/mte.c
@@ -53,7 +53,12 @@
 	 * the new page->flags are visible before the tags were updated.
 	 */
 	smp_wmb();
-	mte_clear_page_tags(page_address(page));
+	/*
+	 * Test PG_mte_tagged again in case it was racing with another
+	 * set_pte_at().
+	 */
+	if (!test_and_set_bit(PG_mte_tagged, &page->flags))
+		mte_clear_page_tags(page_address(page));
 }
 
 void mte_sync_tags(pte_t old_pte, pte_t pte)
@@ -69,10 +74,13 @@
 
 	/* if PG_mte_tagged is set, tags have already been initialised */
 	for (i = 0; i < nr_pages; i++, page++) {
-		if (!test_and_set_bit(PG_mte_tagged, &page->flags))
+		if (!test_bit(PG_mte_tagged, &page->flags))
 			mte_sync_page_tags(page, old_pte, check_swap,
 					   pte_is_tagged);
 	}
+
+	/* ensure the tags are visible before the PTE is set */
+	smp_wmb();
 }
 
 int memcmp_pages(struct page *page1, struct page *page2)
@@ -210,6 +218,49 @@
 	mte_check_tfsr_el1();
 }
 
+void mte_cpu_setup(void)
+{
+	u64 rgsr;
+
+	/*
+	 * CnP must be enabled only after the MAIR_EL1 register has been set
+	 * up. Inconsistent MAIR_EL1 between CPUs sharing the same TLB may
+	 * lead to the wrong memory type being used for a brief window during
+	 * CPU power-up.
+	 *
+	 * CnP is not a boot feature so MTE gets enabled before CnP, but let's
+	 * make sure that is the case.
+	 */
+	BUG_ON(read_sysreg(ttbr0_el1) & TTBR_CNP_BIT);
+	BUG_ON(read_sysreg(ttbr1_el1) & TTBR_CNP_BIT);
+
+	/* Normal Tagged memory type at the corresponding MAIR index */
+	sysreg_clear_set(mair_el1,
+			 MAIR_ATTRIDX(MAIR_ATTR_MASK, MT_NORMAL_TAGGED),
+			 MAIR_ATTRIDX(MAIR_ATTR_NORMAL_TAGGED,
+				      MT_NORMAL_TAGGED));
+
+	write_sysreg_s(KERNEL_GCR_EL1, SYS_GCR_EL1);
+
+	/*
+	 * If GCR_EL1.RRND=1 is implemented the same way as RRND=0, then
+	 * RGSR_EL1.SEED must be non-zero for IRG to produce
+	 * pseudorandom numbers. As RGSR_EL1 is UNKNOWN out of reset, we
+	 * must initialize it.
+	 */
+	rgsr = (read_sysreg(CNTVCT_EL0) & SYS_RGSR_EL1_SEED_MASK) <<
+	       SYS_RGSR_EL1_SEED_SHIFT;
+	if (rgsr == 0)
+		rgsr = 1 << SYS_RGSR_EL1_SEED_SHIFT;
+	write_sysreg_s(rgsr, SYS_RGSR_EL1);
+
+	/* clear any pending tag check faults in TFSR*_EL1 */
+	write_sysreg_s(0, SYS_TFSR_EL1);
+	write_sysreg_s(0, SYS_TFSRE0_EL1);
+
+	local_flush_tlb_all();
+}
+
 void mte_suspend_enter(void)
 {
 	if (!system_supports_mte())
@@ -226,6 +277,14 @@
 	mte_check_tfsr_el1();
 }
 
+void mte_suspend_exit(void)
+{
+	if (!system_supports_mte())
+		return;
+
+	mte_cpu_setup();
+}
+
 long set_mte_ctrl(struct task_struct *task, unsigned long arg)
 {
 	u64 mte_ctrl = (~((arg & PR_MTE_TAG_MASK) >> PR_MTE_TAG_SHIFT) &
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/paravirt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/paravirt.c
@@ -35,7 +35,7 @@
 DEFINE_STATIC_CALL(pv_steal_clock, native_steal_clock);
 
 struct pv_time_stolen_time_region {
-	struct pvclock_vcpu_stolen_time *kaddr;
+	struct pvclock_vcpu_stolen_time __rcu *kaddr;
 };
 
 static DEFINE_PER_CPU(struct pv_time_stolen_time_region, stolen_time_region);
@@ -52,7 +52,9 @@
 /* return stolen time in ns by asking the hypervisor */
 static u64 para_steal_clock(int cpu)
 {
+	struct pvclock_vcpu_stolen_time *kaddr = NULL;
 	struct pv_time_stolen_time_region *reg;
+	u64 ret = 0;
 
 	reg = per_cpu_ptr(&stolen_time_region, cpu);
 
@@ -61,28 +63,37 @@
 	 * online notification callback runs. Until the callback
 	 * has run we just return zero.
 	 */
-	if (!reg->kaddr)
+	rcu_read_lock();
+	kaddr = rcu_dereference(reg->kaddr);
+	if (!kaddr) {
+		rcu_read_unlock();
 		return 0;
+	}
 
-	return le64_to_cpu(READ_ONCE(reg->kaddr->stolen_time));
+	ret = le64_to_cpu(READ_ONCE(kaddr->stolen_time));
+	rcu_read_unlock();
+	return ret;
 }
 
 static int stolen_time_cpu_down_prepare(unsigned int cpu)
 {
+	struct pvclock_vcpu_stolen_time *kaddr = NULL;
 	struct pv_time_stolen_time_region *reg;
 
 	reg = this_cpu_ptr(&stolen_time_region);
 	if (!reg->kaddr)
 		return 0;
 
-	memunmap(reg->kaddr);
-	memset(reg, 0, sizeof(*reg));
+	kaddr = rcu_replace_pointer(reg->kaddr, NULL, true);
+	synchronize_rcu();
+	memunmap(kaddr);
 
 	return 0;
 }
 
 static int stolen_time_cpu_online(unsigned int cpu)
 {
+	struct pvclock_vcpu_stolen_time *kaddr = NULL;
 	struct pv_time_stolen_time_region *reg;
 	struct arm_smccc_res res;
 
@@ -93,17 +104,19 @@
 	if (res.a0 == SMCCC_RET_NOT_SUPPORTED)
 		return -EINVAL;
 
-	reg->kaddr = memremap(res.a0,
+	kaddr = memremap(res.a0,
 			      sizeof(struct pvclock_vcpu_stolen_time),
 			      MEMREMAP_WB);
 
+	rcu_assign_pointer(reg->kaddr, kaddr);
+
 	if (!reg->kaddr) {
 		pr_warn("Failed to map stolen time data structure\n");
 		return -ENOMEM;
 	}
 
-	if (le32_to_cpu(reg->kaddr->revision) != 0 ||
-	    le32_to_cpu(reg->kaddr->attributes) != 0) {
+	if (le32_to_cpu(kaddr->revision) != 0 ||
+	    le32_to_cpu(kaddr->attributes) != 0) {
 		pr_warn_once("Unexpected revision or attributes in stolen time data\n");
 		return -ENXIO;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/patching.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/patching.c
@@ -117,8 +117,8 @@
 	int i, ret = 0;
 	struct aarch64_insn_patch *pp = arg;
 
-	/* The first CPU becomes master */
-	if (atomic_inc_return(&pp->cpu_count) == 1) {
+	/* The last CPU becomes master */
+	if (atomic_inc_return(&pp->cpu_count) == num_online_cpus()) {
 		for (i = 0; ret == 0 && i < pp->insn_cnt; i++)
 			ret = aarch64_insn_patch_text_nosync(pp->text_addrs[i],
 							     pp->new_insns[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/perf_callchain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/perf_callchain.c
@@ -102,7 +102,9 @@
 void perf_callchain_user(struct perf_callchain_entry_ctx *entry,
 			 struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
+
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -147,9 +149,10 @@
 void perf_callchain_kernel(struct perf_callchain_entry_ctx *entry,
 			   struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct stackframe frame;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -160,18 +163,21 @@
 
 unsigned long perf_instruction_pointer(struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
-		return perf_guest_cbs->get_guest_ip();
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
+
+	if (guest_cbs && guest_cbs->is_in_guest())
+		return guest_cbs->get_guest_ip();
 
 	return instruction_pointer(regs);
 }
 
 unsigned long perf_misc_flags(struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	int misc = 0;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		if (perf_guest_cbs->is_user_mode())
+	if (guest_cbs && guest_cbs->is_in_guest()) {
+		if (guest_cbs->is_user_mode())
 			misc |= PERF_RECORD_MISC_GUEST_USER;
 		else
 			misc |= PERF_RECORD_MISC_GUEST_KERNEL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/perf_event.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/perf_event.c
@@ -168,7 +168,11 @@
 	PMU_EVENT_ATTR_ID(name, armv8pmu_events_sysfs_show, config)
 
 static struct attribute *armv8_pmuv3_event_attrs[] = {
-	ARMV8_EVENT_ATTR(sw_incr, ARMV8_PMUV3_PERFCTR_SW_INCR),
+	/*
+	 * Don't expose the sw_incr event in /sys. It's not usable as writes to
+	 * PMSWINC_EL0 will trap as PMUSERENR.{SW,EN}=={0,0} and event rotation
+	 * means we don't have a fixed event<->counter relationship regardless.
+	 */
 	ARMV8_EVENT_ATTR(l1i_cache_refill, ARMV8_PMUV3_PERFCTR_L1I_CACHE_REFILL),
 	ARMV8_EVENT_ATTR(l1i_tlb_refill, ARMV8_PMUV3_PERFCTR_L1I_TLB_REFILL),
 	ARMV8_EVENT_ATTR(l1d_cache_refill, ARMV8_PMUV3_PERFCTR_L1D_CACHE_REFILL),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/probes/decode-insn.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/probes/decode-insn.c
@@ -99,10 +99,6 @@
 	    aarch64_insn_is_blr(insn) ||
 	    aarch64_insn_is_ret(insn)) {
 		api->handler = simulate_br_blr_ret;
-	} else if (aarch64_insn_is_ldr_lit(insn)) {
-		api->handler = simulate_ldr_literal;
-	} else if (aarch64_insn_is_ldrsw_lit(insn)) {
-		api->handler = simulate_ldrsw_literal;
 	} else {
 		/*
 		 * Instruction cannot be stepped out-of-line and we don't
@@ -140,6 +136,17 @@
 	probe_opcode_t insn = le32_to_cpu(*addr);
 	probe_opcode_t *scan_end = NULL;
 	unsigned long size = 0, offset = 0;
+	struct arch_probe_insn *api = &asi->api;
+
+	if (aarch64_insn_is_ldr_lit(insn)) {
+		api->handler = simulate_ldr_literal;
+		decoded = INSN_GOOD_NO_SLOT;
+	} else if (aarch64_insn_is_ldrsw_lit(insn)) {
+		api->handler = simulate_ldrsw_literal;
+		decoded = INSN_GOOD_NO_SLOT;
+	} else {
+		decoded = arm_probe_decode_insn(insn, &asi->api);
+	}
 
 	/*
 	 * If there's a symbol defined in front of and near enough to
@@ -157,7 +164,6 @@
 		else
 			scan_end = addr - MAX_ATOMIC_CONTEXT_SIZE;
 	}
-	decoded = arm_probe_decode_insn(insn, &asi->api);
 
 	if (decoded != INSN_REJECTED && scan_end)
 		if (is_probed_address_atomic(addr - 1, scan_end))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/probes/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/probes/kprobes.c
@@ -7,6 +7,9 @@
  * Copyright (C) 2013 Linaro Limited.
  * Author: Sandeepa Prabhu <sandeepa.prabhu@linaro.org>
  */
+
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/extable.h>
 #include <linux/kasan.h>
 #include <linux/kernel.h>
@@ -218,7 +221,7 @@
 		break;
 	case KPROBE_HIT_SS:
 	case KPROBE_REENTER:
-		pr_warn("Unrecoverable kprobe detected.\n");
+		pr_warn("Failed to recover from reentered kprobes.\n");
 		dump_kprobe(p);
 		BUG();
 		break;
@@ -332,7 +335,7 @@
 }
 
 static int __kprobes
-kprobe_breakpoint_ss_handler(struct pt_regs *regs, unsigned int esr)
+kprobe_breakpoint_ss_handler(struct pt_regs *regs, unsigned long esr)
 {
 	struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
 	unsigned long addr = instruction_pointer(regs);
@@ -356,7 +359,7 @@
 };
 
 static int __kprobes
-kprobe_breakpoint_handler(struct pt_regs *regs, unsigned int esr)
+kprobe_breakpoint_handler(struct pt_regs *regs, unsigned long esr)
 {
 	kprobe_handler(regs);
 	return DBG_HOOK_HANDLED;
@@ -398,8 +401,7 @@
 
 void __kprobes __used *trampoline_probe_handler(struct pt_regs *regs)
 {
-	return (void *)kretprobe_trampoline_handler(regs, &kretprobe_trampoline,
-					(void *)kernel_stack_pointer(regs));
+	return (void *)kretprobe_trampoline_handler(regs, (void *)kernel_stack_pointer(regs));
 }
 
 void __kprobes arch_prepare_kretprobe(struct kretprobe_instance *ri,
@@ -409,7 +411,7 @@
 	ri->fp = (void *)kernel_stack_pointer(regs);
 
 	/* replace return addr (x30) with trampoline */
-	regs->regs[30] = (long)&kretprobe_trampoline;
+	regs->regs[30] = (long)&__kretprobe_trampoline;
 }
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/probes/kprobes_trampoline.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/probes/kprobes_trampoline.S
@@ -61,7 +61,7 @@
 	ldp x28, x29, [sp, #S_X28]
 	.endm
 
-SYM_CODE_START(kretprobe_trampoline)
+SYM_CODE_START(__kretprobe_trampoline)
 	sub sp, sp, #PT_REGS_SIZE
 
 	save_all_base_regs
@@ -79,4 +79,4 @@
 	add sp, sp, #PT_REGS_SIZE
 	ret
 
-SYM_CODE_END(kretprobe_trampoline)
+SYM_CODE_END(__kretprobe_trampoline)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/probes/simulate-insn.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/probes/simulate-insn.c
@@ -171,17 +171,15 @@
 void __kprobes
 simulate_ldr_literal(u32 opcode, long addr, struct pt_regs *regs)
 {
-	u64 *load_addr;
+	unsigned long load_addr;
 	int xn = opcode & 0x1f;
-	int disp;
 
-	disp = ldr_displacement(opcode);
-	load_addr = (u64 *) (addr + disp);
+	load_addr = addr + ldr_displacement(opcode);
 
 	if (opcode & (1 << 30))	/* x0-x30 */
-		set_x_reg(regs, xn, *load_addr);
+		set_x_reg(regs, xn, READ_ONCE(*(u64 *)load_addr));
 	else			/* w0-w30 */
-		set_w_reg(regs, xn, *load_addr);
+		set_w_reg(regs, xn, READ_ONCE(*(u32 *)load_addr));
 
 	instruction_pointer_set(regs, instruction_pointer(regs) + 4);
 }
@@ -189,14 +187,12 @@
 void __kprobes
 simulate_ldrsw_literal(u32 opcode, long addr, struct pt_regs *regs)
 {
-	s32 *load_addr;
+	unsigned long load_addr;
 	int xn = opcode & 0x1f;
-	int disp;
 
-	disp = ldr_displacement(opcode);
-	load_addr = (s32 *) (addr + disp);
+	load_addr = addr + ldr_displacement(opcode);
 
-	set_x_reg(regs, xn, *load_addr);
+	set_x_reg(regs, xn, READ_ONCE(*(s32 *)load_addr));
 
 	instruction_pointer_set(regs, instruction_pointer(regs) + 4);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/probes/uprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/probes/uprobes.c
@@ -42,7 +42,7 @@
 	else if (!IS_ALIGNED(addr, AARCH64_INSN_SIZE))
 		return -EINVAL;
 
-	insn = *(probe_opcode_t *)(&auprobe->insn[0]);
+	insn = le32_to_cpu(auprobe->insn);
 
 	switch (arm_probe_decode_insn(insn, &auprobe->api)) {
 	case INSN_REJECTED:
@@ -108,7 +108,7 @@
 	if (!auprobe->simulate)
 		return false;
 
-	insn = *(probe_opcode_t *)(&auprobe->insn[0]);
+	insn = le32_to_cpu(auprobe->insn);
 	addr = instruction_pointer(regs);
 
 	if (auprobe->api.handler)
@@ -166,7 +166,7 @@
 }
 
 static int uprobe_breakpoint_handler(struct pt_regs *regs,
-		unsigned int esr)
+				     unsigned long esr)
 {
 	if (uprobe_pre_sstep_notifier(regs))
 		return DBG_HOOK_HANDLED;
@@ -175,7 +175,7 @@
 }
 
 static int uprobe_single_step_handler(struct pt_regs *regs,
-		unsigned int esr)
+				      unsigned long esr)
 {
 	struct uprobe_task *utask = current->utask;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/process.c
@@ -394,7 +394,7 @@
 
 	if (is_compat_thread(task_thread_info(next)))
 		write_sysreg(next->thread.uw.tp_value, tpidrro_el0);
-	else if (!arm64_kernel_unmapped_at_el0())
+	else
 		write_sysreg(0, tpidrro_el0);
 
 	write_sysreg(*task_user_tls(next), tpidr_el0);
@@ -439,34 +439,26 @@
 
 /*
  * ARM erratum 1418040 handling, affecting the 32bit view of CNTVCT.
- * Assuming the virtual counter is enabled at the beginning of times:
- *
- * - disable access when switching from a 64bit task to a 32bit task
- * - enable access when switching from a 32bit task to a 64bit task
+ * Ensure access is disabled when switching to a 32bit task, ensure
+ * access is enabled when switching to a 64bit task.
  */
-static void erratum_1418040_thread_switch(struct task_struct *prev,
-					  struct task_struct *next)
+static void erratum_1418040_thread_switch(struct task_struct *next)
 {
-	bool prev32, next32;
-	u64 val;
-
-	if (!IS_ENABLED(CONFIG_ARM64_ERRATUM_1418040))
-		return;
-
-	prev32 = is_compat_thread(task_thread_info(prev));
-	next32 = is_compat_thread(task_thread_info(next));
-
-	if (prev32 == next32 || !this_cpu_has_cap(ARM64_WORKAROUND_1418040))
+	if (!IS_ENABLED(CONFIG_ARM64_ERRATUM_1418040) ||
+	    !this_cpu_has_cap(ARM64_WORKAROUND_1418040))
 		return;
 
-	val = read_sysreg(cntkctl_el1);
-
-	if (!next32)
-		val |= ARCH_TIMER_USR_VCT_ACCESS_EN;
+	if (is_compat_thread(task_thread_info(next)))
+		sysreg_clear_set(cntkctl_el1, ARCH_TIMER_USR_VCT_ACCESS_EN, 0);
 	else
-		val &= ~ARCH_TIMER_USR_VCT_ACCESS_EN;
+		sysreg_clear_set(cntkctl_el1, 0, ARCH_TIMER_USR_VCT_ACCESS_EN);
+}
 
-	write_sysreg(val, cntkctl_el1);
+static void erratum_1418040_new_exec(void)
+{
+	preempt_disable();
+	erratum_1418040_thread_switch(current);
+	preempt_enable();
 }
 
 /*
@@ -501,7 +493,7 @@
 	contextidr_thread_switch(next);
 	entry_task_switch(next);
 	ssbs_thread_switch(next);
-	erratum_1418040_thread_switch(prev, next);
+	erratum_1418040_thread_switch(next);
 	ptrauth_thread_switch_user(next);
 
 	/*
@@ -613,6 +605,7 @@
 	current->mm->context.flags = mmflags;
 	ptrauth_thread_init_user();
 	mte_thread_init_user();
+	erratum_1418040_new_exec();
 
 	if (task_spec_ssb_noexec(current)) {
 		arch_prctl_spec_ctrl_set(current, PR_SPEC_STORE_BYPASS,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/proton-pack.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/proton-pack.c
@@ -18,15 +18,18 @@
  */
 
 #include <linux/arm-smccc.h>
+#include <linux/bpf.h>
 #include <linux/cpu.h>
 #include <linux/device.h>
 #include <linux/nospec.h>
 #include <linux/prctl.h>
 #include <linux/sched/task_stack.h>
 
+#include <asm/debug-monitors.h>
 #include <asm/insn.h>
 #include <asm/spectre.h>
 #include <asm/traps.h>
+#include <asm/vectors.h>
 #include <asm/virt.h>
 
 /*
@@ -96,14 +99,51 @@
 	return ret;
 }
 
+static const char *get_bhb_affected_string(enum mitigation_state bhb_state)
+{
+	switch (bhb_state) {
+	case SPECTRE_UNAFFECTED:
+		return "";
+	default:
+	case SPECTRE_VULNERABLE:
+		return ", but not BHB";
+	case SPECTRE_MITIGATED:
+		return ", BHB";
+	}
+}
+
+static bool _unprivileged_ebpf_enabled(void)
+{
+#ifdef CONFIG_BPF_SYSCALL
+	return !sysctl_unprivileged_bpf_disabled;
+#else
+	return false;
+#endif
+}
+
 ssize_t cpu_show_spectre_v2(struct device *dev, struct device_attribute *attr,
 			    char *buf)
 {
+	enum mitigation_state bhb_state = arm64_get_spectre_bhb_state();
+	const char *bhb_str = get_bhb_affected_string(bhb_state);
+	const char *v2_str = "Branch predictor hardening";
+
 	switch (spectre_v2_state) {
 	case SPECTRE_UNAFFECTED:
-		return sprintf(buf, "Not affected\n");
+		if (bhb_state == SPECTRE_UNAFFECTED)
+			return sprintf(buf, "Not affected\n");
+
+		/*
+		 * Platforms affected by Spectre-BHB can't report
+		 * "Not affected" for Spectre-v2.
+		 */
+		v2_str = "CSV2";
+		fallthrough;
 	case SPECTRE_MITIGATED:
-		return sprintf(buf, "Mitigation: Branch predictor hardening\n");
+		if (bhb_state == SPECTRE_MITIGATED && _unprivileged_ebpf_enabled())
+			return sprintf(buf, "Vulnerable: Unprivileged eBPF enabled\n");
+
+		return sprintf(buf, "Mitigation: %s%s\n", v2_str, bhb_str);
 	case SPECTRE_VULNERABLE:
 		fallthrough;
 	default:
@@ -193,17 +233,20 @@
 	__this_cpu_write(bp_hardening_data.slot, HYP_VECTOR_SPECTRE_DIRECT);
 }
 
-static void call_smc_arch_workaround_1(void)
+/* Called during entry so must be noinstr */
+static noinstr void call_smc_arch_workaround_1(void)
 {
 	arm_smccc_1_1_smc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL);
 }
 
-static void call_hvc_arch_workaround_1(void)
+/* Called during entry so must be noinstr */
+static noinstr void call_hvc_arch_workaround_1(void)
 {
 	arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL);
 }
 
-static void qcom_link_stack_sanitisation(void)
+/* Called during entry so must be noinstr */
+static noinstr void qcom_link_stack_sanitisation(void)
 {
 	u64 tmp;
 
@@ -478,10 +521,13 @@
 	return state != SPECTRE_UNAFFECTED;
 }
 
-static int ssbs_emulation_handler(struct pt_regs *regs, u32 instr)
+bool try_emulate_el1_ssbs(struct pt_regs *regs, u32 instr)
 {
-	if (user_mode(regs))
-		return 1;
+	const u32 instr_mask = ~(1U << PSTATE_Imm_shift);
+	const u32 instr_val = 0xd500401f | PSTATE_SSBS;
+
+	if ((instr & instr_mask) != instr_val)
+		return false;
 
 	if (instr & BIT(PSTATE_Imm_shift))
 		regs->pstate |= PSR_SSBS_BIT;
@@ -489,19 +535,11 @@
 		regs->pstate &= ~PSR_SSBS_BIT;
 
 	arm64_skip_faulting_instruction(regs, 4);
-	return 0;
+	return true;
 }
 
-static struct undef_hook ssbs_emulation_hook = {
-	.instr_mask	= ~(1U << PSTATE_Imm_shift),
-	.instr_val	= 0xd500401f | PSTATE_SSBS,
-	.fn		= ssbs_emulation_handler,
-};
-
 static enum mitigation_state spectre_v4_enable_hw_mitigation(void)
 {
-	static bool undef_hook_registered = false;
-	static DEFINE_RAW_SPINLOCK(hook_lock);
 	enum mitigation_state state;
 
 	/*
@@ -512,13 +550,6 @@
 	if (state != SPECTRE_MITIGATED || !this_cpu_has_cap(ARM64_SSBS))
 		return state;
 
-	raw_spin_lock(&hook_lock);
-	if (!undef_hook_registered) {
-		register_undef_hook(&ssbs_emulation_hook);
-		undef_hook_registered = true;
-	}
-	raw_spin_unlock(&hook_lock);
-
 	if (spectre_v4_mitigations_off()) {
 		sysreg_clear_set(sctlr_el1, 0, SCTLR_ELx_DSSBS);
 		set_pstate_ssbs(1);
@@ -527,6 +558,18 @@
 
 	/* SCTLR_EL1.DSSBS was initialised to 0 during boot */
 	set_pstate_ssbs(0);
+
+	/*
+	 * SSBS is self-synchronizing and is intended to affect subsequent
+	 * speculative instructions, but some CPUs can speculate with a stale
+	 * value of SSBS.
+	 *
+	 * Mitigate this with an unconditional speculation barrier, as CPUs
+	 * could mis-speculate branches and bypass a conditional barrier.
+	 */
+	if (IS_ENABLED(CONFIG_ARM64_ERRATUM_3194386))
+		spec_bar();
+
 	return SPECTRE_MITIGATED;
 }
 
@@ -554,9 +597,9 @@
  * Patch a NOP in the Spectre-v4 mitigation code with an SMC/HVC instruction
  * to call into firmware to adjust the mitigation state.
  */
-void __init spectre_v4_patch_fw_mitigation_conduit(struct alt_instr *alt,
-						   __le32 *origptr,
-						   __le32 *updptr, int nr_inst)
+void __init smccc_patch_fw_mitigation_conduit(struct alt_instr *alt,
+					       __le32 *origptr,
+					       __le32 *updptr, int nr_inst)
 {
 	u32 insn;
 
@@ -770,3 +813,351 @@
 		return -ENODEV;
 	}
 }
+
+/*
+ * Spectre BHB.
+ *
+ * A CPU is either:
+ * - Mitigated by a branchy loop a CPU specific number of times, and listed
+ *   in our "loop mitigated list".
+ * - Mitigated in software by the firmware Spectre v2 call.
+ * - Has the ClearBHB instruction to perform the mitigation.
+ * - Has the 'Exception Clears Branch History Buffer' (ECBHB) feature, so no
+ *   software mitigation in the vectors is needed.
+ * - Has CSV2.3, so is unaffected.
+ */
+static enum mitigation_state spectre_bhb_state;
+
+enum mitigation_state arm64_get_spectre_bhb_state(void)
+{
+	return spectre_bhb_state;
+}
+
+enum bhb_mitigation_bits {
+	BHB_LOOP,
+	BHB_FW,
+	BHB_HW,
+	BHB_INSN,
+};
+static unsigned long system_bhb_mitigations;
+
+/*
+ * This must be called with SCOPE_LOCAL_CPU for each type of CPU, before any
+ * SCOPE_SYSTEM call will give the right answer.
+ */
+u8 spectre_bhb_loop_affected(int scope)
+{
+	u8 k = 0;
+	static u8 max_bhb_k;
+
+	if (scope == SCOPE_LOCAL_CPU) {
+		static const struct midr_range spectre_bhb_k32_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A78),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A78AE),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A78C),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_X1),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_X2),
+			MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
+			MIDR_ALL_VERSIONS(MIDR_NEOVERSE_V1),
+			{},
+		};
+		static const struct midr_range spectre_bhb_k24_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A76),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A77),
+			MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N1),
+			{},
+		};
+		static const struct midr_range spectre_bhb_k11_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_AMPERE1),
+			{},
+		};
+		static const struct midr_range spectre_bhb_k8_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A72),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A57),
+			{},
+		};
+
+		if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k32_list))
+			k = 32;
+		else if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k24_list))
+			k = 24;
+		else if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k11_list))
+			k = 11;
+		else if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k8_list))
+			k =  8;
+
+		max_bhb_k = max(max_bhb_k, k);
+	} else {
+		k = max_bhb_k;
+	}
+
+	return k;
+}
+
+static enum mitigation_state spectre_bhb_get_cpu_fw_mitigation_state(void)
+{
+	int ret;
+	struct arm_smccc_res res;
+
+	arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
+			     ARM_SMCCC_ARCH_WORKAROUND_3, &res);
+
+	ret = res.a0;
+	switch (ret) {
+	case SMCCC_RET_SUCCESS:
+		return SPECTRE_MITIGATED;
+	case SMCCC_ARCH_WORKAROUND_RET_UNAFFECTED:
+		return SPECTRE_UNAFFECTED;
+	default:
+		fallthrough;
+	case SMCCC_RET_NOT_SUPPORTED:
+		return SPECTRE_VULNERABLE;
+	}
+}
+
+static bool is_spectre_bhb_fw_affected(int scope)
+{
+	static bool system_affected;
+	enum mitigation_state fw_state;
+	bool has_smccc = arm_smccc_1_1_get_conduit() != SMCCC_CONDUIT_NONE;
+	static const struct midr_range spectre_bhb_firmware_mitigated_list[] = {
+		MIDR_ALL_VERSIONS(MIDR_CORTEX_A73),
+		MIDR_ALL_VERSIONS(MIDR_CORTEX_A75),
+		{},
+	};
+	bool cpu_in_list = is_midr_in_range_list(read_cpuid_id(),
+					 spectre_bhb_firmware_mitigated_list);
+
+	if (scope != SCOPE_LOCAL_CPU)
+		return system_affected;
+
+	fw_state = spectre_bhb_get_cpu_fw_mitigation_state();
+	if (cpu_in_list || (has_smccc && fw_state == SPECTRE_MITIGATED)) {
+		system_affected = true;
+		return true;
+	}
+
+	return false;
+}
+
+static bool supports_ecbhb(int scope)
+{
+	u64 mmfr1;
+
+	if (scope == SCOPE_LOCAL_CPU)
+		mmfr1 = read_sysreg_s(SYS_ID_AA64MMFR1_EL1);
+	else
+		mmfr1 = read_sanitised_ftr_reg(SYS_ID_AA64MMFR1_EL1);
+
+	return cpuid_feature_extract_unsigned_field(mmfr1,
+						    ID_AA64MMFR1_ECBHB_SHIFT);
+}
+
+bool is_spectre_bhb_affected(const struct arm64_cpu_capabilities *entry,
+			     int scope)
+{
+	WARN_ON(scope != SCOPE_LOCAL_CPU || preemptible());
+
+	if (supports_csv2p3(scope))
+		return false;
+
+	if (supports_clearbhb(scope))
+		return true;
+
+	if (spectre_bhb_loop_affected(scope))
+		return true;
+
+	if (is_spectre_bhb_fw_affected(scope))
+		return true;
+
+	return false;
+}
+
+static void this_cpu_set_vectors(enum arm64_bp_harden_el1_vectors slot)
+{
+	const char *v = arm64_get_bp_hardening_vector(slot);
+
+	if (slot < 0)
+		return;
+
+	__this_cpu_write(this_cpu_vector, v);
+
+	/*
+	 * When KPTI is in use, the vectors are switched when exiting to
+	 * user-space.
+	 */
+	if (arm64_kernel_unmapped_at_el0())
+		return;
+
+	write_sysreg(v, vbar_el1);
+	isb();
+}
+
+void spectre_bhb_enable_mitigation(const struct arm64_cpu_capabilities *entry)
+{
+	bp_hardening_cb_t cpu_cb;
+	enum mitigation_state fw_state, state = SPECTRE_VULNERABLE;
+	struct bp_hardening_data *data = this_cpu_ptr(&bp_hardening_data);
+
+	if (!is_spectre_bhb_affected(entry, SCOPE_LOCAL_CPU))
+		return;
+
+	if (arm64_get_spectre_v2_state() == SPECTRE_VULNERABLE) {
+		/* No point mitigating Spectre-BHB alone. */
+	} else if (!IS_ENABLED(CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY)) {
+		pr_info_once("spectre-bhb mitigation disabled by compile time option\n");
+	} else if (cpu_mitigations_off()) {
+		pr_info_once("spectre-bhb mitigation disabled by command line option\n");
+	} else if (supports_ecbhb(SCOPE_LOCAL_CPU)) {
+		state = SPECTRE_MITIGATED;
+		set_bit(BHB_HW, &system_bhb_mitigations);
+	} else if (supports_clearbhb(SCOPE_LOCAL_CPU)) {
+		/*
+		 * Ensure KVM uses the indirect vector which will have ClearBHB
+		 * added.
+		 */
+		if (!data->slot)
+			data->slot = HYP_VECTOR_INDIRECT;
+
+		this_cpu_set_vectors(EL1_VECTOR_BHB_CLEAR_INSN);
+		state = SPECTRE_MITIGATED;
+		set_bit(BHB_INSN, &system_bhb_mitigations);
+	} else if (spectre_bhb_loop_affected(SCOPE_LOCAL_CPU)) {
+		/*
+		 * Ensure KVM uses the indirect vector which will have the
+		 * branchy-loop added. A57/A72-r0 will already have selected
+		 * the spectre-indirect vector, which is sufficient for BHB
+		 * too.
+		 */
+		if (!data->slot)
+			data->slot = HYP_VECTOR_INDIRECT;
+
+		this_cpu_set_vectors(EL1_VECTOR_BHB_LOOP);
+		state = SPECTRE_MITIGATED;
+		set_bit(BHB_LOOP, &system_bhb_mitigations);
+	} else if (is_spectre_bhb_fw_affected(SCOPE_LOCAL_CPU)) {
+		fw_state = spectre_bhb_get_cpu_fw_mitigation_state();
+		if (fw_state == SPECTRE_MITIGATED) {
+			/*
+			 * Ensure KVM uses one of the spectre bp_hardening
+			 * vectors. The indirect vector doesn't include the EL3
+			 * call, so needs upgrading to
+			 * HYP_VECTOR_SPECTRE_INDIRECT.
+			 */
+			if (!data->slot || data->slot == HYP_VECTOR_INDIRECT)
+				data->slot += 1;
+
+			this_cpu_set_vectors(EL1_VECTOR_BHB_FW);
+
+			/*
+			 * The WA3 call in the vectors supersedes the WA1 call
+			 * made during context-switch. Uninstall any firmware
+			 * bp_hardening callback.
+			 */
+			cpu_cb = spectre_v2_get_sw_mitigation_cb();
+			if (__this_cpu_read(bp_hardening_data.fn) != cpu_cb)
+				__this_cpu_write(bp_hardening_data.fn, NULL);
+
+			state = SPECTRE_MITIGATED;
+			set_bit(BHB_FW, &system_bhb_mitigations);
+		}
+	}
+
+	update_mitigation_state(&spectre_bhb_state, state);
+}
+
+/* Patched to NOP when enabled */
+void noinstr spectre_bhb_patch_loop_mitigation_enable(struct alt_instr *alt,
+						     __le32 *origptr,
+						      __le32 *updptr, int nr_inst)
+{
+	BUG_ON(nr_inst != 1);
+
+	if (test_bit(BHB_LOOP, &system_bhb_mitigations))
+		*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+}
+
+/* Patched to NOP when enabled */
+void noinstr spectre_bhb_patch_fw_mitigation_enabled(struct alt_instr *alt,
+						   __le32 *origptr,
+						   __le32 *updptr, int nr_inst)
+{
+	BUG_ON(nr_inst != 1);
+
+	if (test_bit(BHB_FW, &system_bhb_mitigations))
+		*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+}
+
+/* Patched to correct the immediate */
+void noinstr spectre_bhb_patch_loop_iter(struct alt_instr *alt,
+				   __le32 *origptr, __le32 *updptr, int nr_inst)
+{
+	u8 rd;
+	u32 insn;
+	u16 loop_count = spectre_bhb_loop_affected(SCOPE_SYSTEM);
+
+	BUG_ON(nr_inst != 1); /* MOV -> MOV */
+
+	if (!IS_ENABLED(CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY))
+		return;
+
+	insn = le32_to_cpu(*origptr);
+	rd = aarch64_insn_decode_register(AARCH64_INSN_REGTYPE_RD, insn);
+	insn = aarch64_insn_gen_movewide(rd, loop_count, 0,
+					 AARCH64_INSN_VARIANT_64BIT,
+					 AARCH64_INSN_MOVEWIDE_ZERO);
+	*updptr++ = cpu_to_le32(insn);
+}
+
+/* Patched to mov WA3 when supported */
+void noinstr spectre_bhb_patch_wa3(struct alt_instr *alt,
+				   __le32 *origptr, __le32 *updptr, int nr_inst)
+{
+	u8 rd;
+	u32 insn;
+
+	BUG_ON(nr_inst != 1); /* MOV -> MOV */
+
+	if (!IS_ENABLED(CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY) ||
+	    !test_bit(BHB_FW, &system_bhb_mitigations))
+		return;
+
+	insn = le32_to_cpu(*origptr);
+	rd = aarch64_insn_decode_register(AARCH64_INSN_REGTYPE_RD, insn);
+
+	insn = aarch64_insn_gen_logical_immediate(AARCH64_INSN_LOGIC_ORR,
+						  AARCH64_INSN_VARIANT_32BIT,
+						  AARCH64_INSN_REG_ZR, rd,
+						  ARM_SMCCC_ARCH_WORKAROUND_3);
+	if (WARN_ON_ONCE(insn == AARCH64_BREAK_FAULT))
+		return;
+
+	*updptr++ = cpu_to_le32(insn);
+}
+
+/* Patched to NOP when not supported */
+void __init spectre_bhb_patch_clearbhb(struct alt_instr *alt,
+				   __le32 *origptr, __le32 *updptr, int nr_inst)
+{
+	BUG_ON(nr_inst != 2);
+
+	if (test_bit(BHB_INSN, &system_bhb_mitigations))
+		return;
+
+	*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+	*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+}
+
+#ifdef CONFIG_BPF_SYSCALL
+#define EBPF_WARN "Unprivileged eBPF is enabled, data leaks possible via Spectre v2 BHB attacks!\n"
+void unpriv_ebpf_notify(int new_state)
+{
+	if (spectre_v2_state == SPECTRE_VULNERABLE ||
+	    spectre_bhb_state != SPECTRE_MITIGATED)
+		return;
+
+	if (!new_state)
+		pr_err("WARNING: %s", EBPF_WARN);
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/ptrace.c
@@ -1075,7 +1075,7 @@
 {
 	long ctrl = get_tagged_addr_ctrl(target);
 
-	if (IS_ERR_VALUE(ctrl))
+	if (WARN_ON_ONCE(IS_ERR_VALUE(ctrl)))
 		return ctrl;
 
 	return membuf_write(&to, &ctrl, sizeof(ctrl));
@@ -1089,6 +1089,10 @@
 	int ret;
 	long ctrl;
 
+	ctrl = get_tagged_addr_ctrl(target);
+	if (WARN_ON_ONCE(IS_ERR_VALUE(ctrl)))
+		return ctrl;
+
 	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &ctrl, 0, -1);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/sdei.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/sdei.c
@@ -47,6 +47,9 @@
 DEFINE_PER_CPU(unsigned long *, sdei_shadow_call_stack_critical_ptr);
 #endif
 
+DEFINE_PER_CPU(struct sdei_registered_event *, sdei_active_normal_event);
+DEFINE_PER_CPU(struct sdei_registered_event *, sdei_active_critical_event);
+
 static void _free_sdei_stack(unsigned long * __percpu *ptr, int cpu)
 {
 	unsigned long *p;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/setup.c
@@ -364,9 +364,6 @@
 	smp_init_cpus();
 	smp_build_mpidr_hash();
 
-	/* Init percpu seeds for random tags after cpus are set up. */
-	kasan_init_sw_tags();
-
 #ifdef CONFIG_ARM64_SW_TTBR0_PAN
 	/*
 	 * Make sure init_thread_info.ttbr0 always generates translation
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/signal.c
@@ -577,10 +577,12 @@
 {
 	int err;
 
-	err = sigframe_alloc(user, &user->fpsimd_offset,
-			     sizeof(struct fpsimd_context));
-	if (err)
-		return err;
+	if (system_supports_fpsimd()) {
+		err = sigframe_alloc(user, &user->fpsimd_offset,
+				     sizeof(struct fpsimd_context));
+		if (err)
+			return err;
+	}
 
 	/* fault information, if valid */
 	if (add_all || current->thread.fault_code) {
@@ -1010,6 +1012,7 @@
 static_assert(offsetof(siginfo_t, si_pkey)	== 0x20);
 static_assert(offsetof(siginfo_t, si_perf_data)	== 0x18);
 static_assert(offsetof(siginfo_t, si_perf_type)	== 0x20);
+static_assert(offsetof(siginfo_t, si_perf_flags) == 0x24);
 static_assert(offsetof(siginfo_t, si_band)	== 0x10);
 static_assert(offsetof(siginfo_t, si_fd)	== 0x18);
 static_assert(offsetof(siginfo_t, si_call_addr)	== 0x10);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/signal32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/signal32.c
@@ -487,6 +487,7 @@
 static_assert(offsetof(compat_siginfo_t, si_pkey)	== 0x14);
 static_assert(offsetof(compat_siginfo_t, si_perf_data)	== 0x10);
 static_assert(offsetof(compat_siginfo_t, si_perf_type)	== 0x14);
+static_assert(offsetof(compat_siginfo_t, si_perf_flags)	== 0x18);
 static_assert(offsetof(compat_siginfo_t, si_band)	== 0x0c);
 static_assert(offsetof(compat_siginfo_t, si_fd)		== 0x10);
 static_assert(offsetof(compat_siginfo_t, si_call_addr)	== 0x0c);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/smccc-call.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/smccc-call.S
@@ -7,48 +7,19 @@
 
 #include <asm/asm-offsets.h>
 #include <asm/assembler.h>
-#include <asm/thread_info.h>
-
-/*
- * If we have SMCCC v1.3 and (as is likely) no SVE state in
- * the registers then set the SMCCC hint bit to say there's no
- * need to preserve it.  Do this by directly adjusting the SMCCC
- * function value which is already stored in x0 ready to be called.
- */
-SYM_FUNC_START(__arm_smccc_sve_check)
-
-	ldr_l	x16, smccc_has_sve_hint
-	cbz	x16, 2f
-
-	get_current_task x16
-	ldr	x16, [x16, #TSK_TI_FLAGS]
-	tbnz	x16, #TIF_FOREIGN_FPSTATE, 1f	// Any live FP state?
-	tbnz	x16, #TIF_SVE, 2f		// Does that state include SVE?
-
-1:	orr	x0, x0, ARM_SMCCC_1_3_SVE_HINT
-
-2:	ret
-SYM_FUNC_END(__arm_smccc_sve_check)
-EXPORT_SYMBOL(__arm_smccc_sve_check)
 
 	.macro SMCCC instr
-	stp     x29, x30, [sp, #-16]!
-	mov	x29, sp
-alternative_if ARM64_SVE
-	bl	__arm_smccc_sve_check
-alternative_else_nop_endif
 	\instr	#0
-	ldr	x4, [sp, #16]
+	ldr	x4, [sp]
 	stp	x0, x1, [x4, #ARM_SMCCC_RES_X0_OFFS]
 	stp	x2, x3, [x4, #ARM_SMCCC_RES_X2_OFFS]
-	ldr	x4, [sp, #24]
+	ldr	x4, [sp, #8]
 	cbz	x4, 1f /* no quirk structure */
 	ldr	x9, [x4, #ARM_SMCCC_QUIRK_ID_OFFS]
 	cmp	x9, #ARM_SMCCC_QUIRK_QCOM_A6
 	b.ne	1f
 	str	x6, [x4, ARM_SMCCC_QUIRK_STATE_OFFS]
-1:	ldp     x29, x30, [sp], #16
-	ret
+1:	ret
 	.endm
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/smp.c
@@ -234,6 +234,7 @@
 	 * Log the CPU info before it is marked online and might get read.
 	 */
 	cpuinfo_store_cpu();
+	store_cpu_topology(cpu);
 
 	/*
 	 * Enable GIC and timers.
@@ -242,7 +243,6 @@
 
 	ipi_setup(cpu);
 
-	store_cpu_topology(cpu);
 	numa_add_cpu(cpu);
 
 	/*
@@ -464,6 +464,8 @@
 		init_gic_priority_masking();
 
 	kasan_init_hw_tags();
+	/* Init percpu seeds for random tags after cpus are set up. */
+	kasan_init_sw_tags();
 }
 
 static u64 __init of_get_cpu_mpidr(struct device_node *dn)
@@ -1073,10 +1075,8 @@
 	 * If this cpu is the only one alive at this point in time, online or
 	 * not, there are no stop messages to be sent around, so just back out.
 	 */
-	if (num_other_online_cpus() == 0) {
-		sdei_mask_local_cpu();
-		return;
-	}
+	if (num_other_online_cpus() == 0)
+		goto skip_ipi;
 
 	cpumask_copy(&mask, cpu_online_mask);
 	cpumask_clear_cpu(smp_processor_id(), &mask);
@@ -1095,7 +1095,9 @@
 		pr_warn("SMP: failed to stop secondary CPUs %*pbl\n",
 			cpumask_pr_args(&mask));
 
+skip_ipi:
 	sdei_mask_local_cpu();
+	sdei_handler_abort();
 }
 
 bool smp_crash_stop_failed(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/stacktrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/stacktrace.c
@@ -33,7 +33,7 @@
  */
 
 
-void start_backtrace(struct stackframe *frame, unsigned long fp,
+notrace void start_backtrace(struct stackframe *frame, unsigned long fp,
 		     unsigned long pc)
 {
 	frame->fp = fp;
@@ -55,6 +55,7 @@
 	frame->prev_fp = 0;
 	frame->prev_type = STACK_TYPE_UNKNOWN;
 }
+NOKPROBE_SYMBOL(start_backtrace);
 
 /*
  * Unwind from one frame record (A) to the next frame record (B).
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/suspend.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/suspend.c
@@ -43,6 +43,8 @@
 {
 	unsigned int cpu = smp_processor_id();
 
+	mte_suspend_exit();
+
 	/*
 	 * We are resuming from reset with the idmap active in TTBR0_EL1.
 	 * We must uninstall the idmap and restore the expected MMU
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/sys_compat.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/sys_compat.c
@@ -114,6 +114,6 @@
 	addr = instruction_pointer(regs) - (compat_thumb_mode(regs) ? 2 : 4);
 
 	arm64_notify_die("Oops - bad compat syscall(2)", regs,
-			 SIGILL, ILL_ILLTRP, addr, scno);
+			 SIGILL, ILL_ILLTRP, addr, 0);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/topology.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/topology.c
@@ -22,46 +22,6 @@
 #include <asm/cputype.h>
 #include <asm/topology.h>
 
-void store_cpu_topology(unsigned int cpuid)
-{
-	struct cpu_topology *cpuid_topo = &cpu_topology[cpuid];
-	u64 mpidr;
-
-	if (cpuid_topo->package_id != -1)
-		goto topology_populated;
-
-	mpidr = read_cpuid_mpidr();
-
-	/* Uniprocessor systems can rely on default topology values */
-	if (mpidr & MPIDR_UP_BITMASK)
-		return;
-
-	/*
-	 * This would be the place to create cpu topology based on MPIDR.
-	 *
-	 * However, it cannot be trusted to depict the actual topology; some
-	 * pieces of the architecture enforce an artificial cap on Aff0 values
-	 * (e.g. GICv3's ICC_SGI1R_EL1 limits it to 15), leading to an
-	 * artificial cycling of Aff1, Aff2 and Aff3 values. IOW, these end up
-	 * having absolutely no relationship to the actual underlying system
-	 * topology, and cannot be reasonably used as core / package ID.
-	 *
-	 * If the MT bit is set, Aff0 *could* be used to define a thread ID, but
-	 * we still wouldn't be able to obtain a sane core ID. This means we
-	 * need to entirely ignore MPIDR for any topology deduction.
-	 */
-	cpuid_topo->thread_id  = -1;
-	cpuid_topo->core_id    = cpuid;
-	cpuid_topo->package_id = cpu_to_node(cpuid);
-
-	pr_debug("CPU%u: cluster %d core %d thread %d mpidr %#016llx\n",
-		 cpuid, cpuid_topo->package_id, cpuid_topo->core_id,
-		 cpuid_topo->thread_id, mpidr);
-
-topology_populated:
-	update_siblings_masks(cpuid);
-}
-
 #ifdef CONFIG_ACPI
 static bool __init acpi_cpu_is_threaded(int cpu)
 {
@@ -249,7 +209,7 @@
 	for_each_cpu(cpu, cpus) {
 		if (!freq_counters_valid(cpu) ||
 		    freq_inv_set_max_ratio(cpu,
-					   cpufreq_get_hw_max_freq(cpu) * 1000,
+					   cpufreq_get_hw_max_freq(cpu) * 1000ULL,
 					   arch_timer_get_rate()))
 			return;
 	}
@@ -308,12 +268,25 @@
 
 static void cpu_read_corecnt(void *val)
 {
+	/*
+	 * A value of 0 can be returned if the current CPU does not support AMUs
+	 * or if the counter is disabled for this CPU. A return value of 0 at
+	 * counter read is properly handled as an error case by the users of the
+	 * counter.
+	 */
 	*(u64 *)val = read_corecnt();
 }
 
 static void cpu_read_constcnt(void *val)
 {
-	*(u64 *)val = read_constcnt();
+	/*
+	 * Return 0 if the current CPU is affected by erratum 2457168. A value
+	 * of 0 is also returned if the current CPU does not support AMUs or if
+	 * the counter is disabled. A return value of 0 at counter read is
+	 * properly handled as an error case by the users of the counter.
+	 */
+	*(u64 *)val = this_cpu_has_cap(ARM64_WORKAROUND_2457168) ?
+		      0UL : read_constcnt();
 }
 
 static inline
@@ -340,7 +313,22 @@
  */
 bool cpc_ffh_supported(void)
 {
-	return freq_counters_valid(get_cpu_with_amu_feat());
+	int cpu = get_cpu_with_amu_feat();
+
+	/*
+	 * FFH is considered supported if there is at least one present CPU that
+	 * supports AMUs. Using FFH to read core and reference counters for CPUs
+	 * that do not support AMUs, have counters disabled or that are affected
+	 * by errata, will result in a return value of 0.
+	 *
+	 * This is done to allow any enabled and valid counters to be read
+	 * through FFH, knowing that potentially returning 0 as counter value is
+	 * properly handled by the users of these counters.
+	 */
+	if ((cpu >= nr_cpu_ids) || !cpumask_test_cpu(cpu, cpu_present_mask))
+		return false;
+
+	return true;
 }
 
 int cpc_read_ffh(int cpu, struct cpc_reg *reg, u64 *val)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/traps.c
@@ -181,12 +181,12 @@
 
 #define S_SMP " SMP"
 
-static int __die(const char *str, int err, struct pt_regs *regs)
+static int __die(const char *str, long err, struct pt_regs *regs)
 {
 	static int die_counter;
 	int ret;
 
-	pr_emerg("Internal error: %s: %x [#%d]" S_PREEMPT S_SMP "\n",
+	pr_emerg("Internal error: %s: %016lx [#%d]" S_PREEMPT S_SMP "\n",
 		 str, err, ++die_counter);
 
 	/* trap and error numbers are mostly meaningless on ARM */
@@ -207,7 +207,7 @@
 /*
  * This function is protected against re-entrancy.
  */
-void die(const char *str, struct pt_regs *regs, int err)
+void die(const char *str, struct pt_regs *regs, long err)
 {
 	int ret;
 	unsigned long flags;
@@ -235,7 +235,7 @@
 	raw_spin_unlock_irqrestore(&die_lock, flags);
 
 	if (ret != NOTIFY_STOP)
-		do_exit(SIGSEGV);
+		make_task_dead(SIGSEGV);
 }
 
 static void arm64_show_signal(int signo, const char *str)
@@ -243,7 +243,7 @@
 	static DEFINE_RATELIMIT_STATE(rs, DEFAULT_RATELIMIT_INTERVAL,
 				      DEFAULT_RATELIMIT_BURST);
 	struct task_struct *tsk = current;
-	unsigned int esr = tsk->thread.fault_code;
+	unsigned long esr = tsk->thread.fault_code;
 	struct pt_regs *regs = task_pt_regs(tsk);
 
 	/* Leave if the signal won't be shown */
@@ -254,7 +254,7 @@
 
 	pr_info("%s[%d]: unhandled exception: ", tsk->comm, task_pid_nr(tsk));
 	if (esr)
-		pr_cont("%s, ESR 0x%08x, ", esr_get_class_string(esr), esr);
+		pr_cont("%s, ESR 0x%016lx, ", esr_get_class_string(esr), esr);
 
 	pr_cont("%s", str);
 	print_vma_addr(KERN_CONT " in ", regs->pc);
@@ -288,7 +288,7 @@
 
 void arm64_notify_die(const char *str, struct pt_regs *regs,
 		      int signo, int sicode, unsigned long far,
-		      int err)
+		      unsigned long err)
 {
 	if (user_mode(regs)) {
 		WARN_ON(regs != current_pt_regs());
@@ -373,51 +373,22 @@
 		regs->pstate &= ~PSR_BTYPE_MASK;
 }
 
-static LIST_HEAD(undef_hook);
-static DEFINE_RAW_SPINLOCK(undef_lock);
-
-void register_undef_hook(struct undef_hook *hook)
+static int user_insn_read(struct pt_regs *regs, u32 *insnp)
 {
-	unsigned long flags;
-
-	raw_spin_lock_irqsave(&undef_lock, flags);
-	list_add(&hook->node, &undef_hook);
-	raw_spin_unlock_irqrestore(&undef_lock, flags);
-}
-
-void unregister_undef_hook(struct undef_hook *hook)
-{
-	unsigned long flags;
-
-	raw_spin_lock_irqsave(&undef_lock, flags);
-	list_del(&hook->node);
-	raw_spin_unlock_irqrestore(&undef_lock, flags);
-}
-
-static int call_undef_hook(struct pt_regs *regs)
-{
-	struct undef_hook *hook;
-	unsigned long flags;
 	u32 instr;
-	int (*fn)(struct pt_regs *regs, u32 instr) = NULL;
 	void __user *pc = (void __user *)instruction_pointer(regs);
 
-	if (!user_mode(regs)) {
-		__le32 instr_le;
-		if (get_kernel_nofault(instr_le, (__force __le32 *)pc))
-			goto exit;
-		instr = le32_to_cpu(instr_le);
-	} else if (compat_thumb_mode(regs)) {
+	if (compat_thumb_mode(regs)) {
 		/* 16-bit Thumb instruction */
 		__le16 instr_le;
 		if (get_user(instr_le, (__le16 __user *)pc))
-			goto exit;
+			return -EFAULT;
 		instr = le16_to_cpu(instr_le);
 		if (aarch32_insn_is_wide(instr)) {
 			u32 instr2;
 
 			if (get_user(instr_le, (__le16 __user *)(pc + 2)))
-				goto exit;
+				return -EFAULT;
 			instr2 = le16_to_cpu(instr_le);
 			instr = (instr << 16) | instr2;
 		}
@@ -425,22 +396,15 @@
 		/* 32-bit ARM instruction */
 		__le32 instr_le;
 		if (get_user(instr_le, (__le32 __user *)pc))
-			goto exit;
+			return -EFAULT;
 		instr = le32_to_cpu(instr_le);
 	}
 
-	raw_spin_lock_irqsave(&undef_lock, flags);
-	list_for_each_entry(hook, &undef_hook, node)
-		if ((instr & hook->instr_mask) == hook->instr_val &&
-			(regs->pstate & hook->pstate_mask) == hook->pstate_val)
-			fn = hook->fn;
-
-	raw_spin_unlock_irqrestore(&undef_lock, flags);
-exit:
-	return fn ? fn(regs, instr) : 1;
+	*insnp = instr;
+	return 0;
 }
 
-void force_signal_inject(int signal, int code, unsigned long address, unsigned int err)
+void force_signal_inject(int signal, int code, unsigned long address, unsigned long err)
 {
 	const char *desc;
 	struct pt_regs *regs = current_pt_regs();
@@ -486,37 +450,64 @@
 	force_signal_inject(SIGSEGV, code, addr, 0);
 }
 
-void do_undefinstr(struct pt_regs *regs)
+void do_el0_undef(struct pt_regs *regs, unsigned long esr)
 {
+	u32 insn;
+
 	/* check for AArch32 breakpoint instructions */
 	if (!aarch32_break_handler(regs))
 		return;
 
-	if (call_undef_hook(regs) == 0)
+	if (user_insn_read(regs, &insn))
+		goto out_err;
+
+	if (try_emulate_mrs(regs, insn))
 		return;
 
-	BUG_ON(!user_mode(regs));
+	if (try_emulate_armv8_deprecated(regs, insn))
+		return;
+
+out_err:
 	force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
 }
-NOKPROBE_SYMBOL(do_undefinstr);
 
-void do_bti(struct pt_regs *regs)
+void do_el1_undef(struct pt_regs *regs, unsigned long esr)
+{
+	u32 insn;
+
+	if (aarch64_insn_read((void *)regs->pc, &insn))
+		goto out_err;
+
+	if (try_emulate_el1_ssbs(regs, insn))
+		return;
+
+out_err:
+	die("Oops - Undefined instruction", regs, esr);
+}
+
+void do_el0_bti(struct pt_regs *regs)
 {
-	BUG_ON(!user_mode(regs));
 	force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
 }
-NOKPROBE_SYMBOL(do_bti);
 
-void do_ptrauth_fault(struct pt_regs *regs, unsigned int esr)
+void do_el1_bti(struct pt_regs *regs, unsigned long esr)
+{
+	die("Oops - BTI", regs, esr);
+}
+
+void do_el0_fpac(struct pt_regs *regs, unsigned long esr)
+{
+	force_signal_inject(SIGILL, ILL_ILLOPN, regs->pc, esr);
+}
+
+void do_el1_fpac(struct pt_regs *regs, unsigned long esr)
 {
 	/*
-	 * Unexpected FPAC exception or pointer authentication failure in
-	 * the kernel: kill the task before it does any more harm.
+	 * Unexpected FPAC exception in the kernel: kill the task before it
+	 * does any more harm.
 	 */
-	BUG_ON(!user_mode(regs));
-	force_signal_inject(SIGILL, ILL_ILLOPN, regs->pc, esr);
+	die("Oops - FPAC", regs, esr);
 }
-NOKPROBE_SYMBOL(do_ptrauth_fault);
 
 #define __user_cache_maint(insn, address, res)			\
 	if (address >= user_addr_max()) {			\
@@ -538,7 +529,7 @@
 		uaccess_ttbr0_disable();			\
 	}
 
-static void user_cache_maint_handler(unsigned int esr, struct pt_regs *regs)
+static void user_cache_maint_handler(unsigned long esr, struct pt_regs *regs)
 {
 	unsigned long tagged_address, address;
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
@@ -578,7 +569,7 @@
 		arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void ctr_read_handler(unsigned int esr, struct pt_regs *regs)
+static void ctr_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
 	unsigned long val = arm64_ftr_reg_user_value(&arm64_ftr_reg_ctrel0);
@@ -597,7 +588,7 @@
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void cntvct_read_handler(unsigned int esr, struct pt_regs *regs)
+static void cntvct_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
 
@@ -605,7 +596,7 @@
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void cntfrq_read_handler(unsigned int esr, struct pt_regs *regs)
+static void cntfrq_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
 
@@ -613,7 +604,7 @@
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void mrs_handler(unsigned int esr, struct pt_regs *regs)
+static void mrs_handler(unsigned long esr, struct pt_regs *regs)
 {
 	u32 sysreg, rt;
 
@@ -624,15 +615,15 @@
 		force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
 }
 
-static void wfi_handler(unsigned int esr, struct pt_regs *regs)
+static void wfi_handler(unsigned long esr, struct pt_regs *regs)
 {
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
 struct sys64_hook {
-	unsigned int esr_mask;
-	unsigned int esr_val;
-	void (*handler)(unsigned int esr, struct pt_regs *regs);
+	unsigned long esr_mask;
+	unsigned long esr_val;
+	void (*handler)(unsigned long esr, struct pt_regs *regs);
 };
 
 static const struct sys64_hook sys64_hooks[] = {
@@ -675,7 +666,7 @@
 };
 
 #ifdef CONFIG_COMPAT
-static bool cp15_cond_valid(unsigned int esr, struct pt_regs *regs)
+static bool cp15_cond_valid(unsigned long esr, struct pt_regs *regs)
 {
 	int cond;
 
@@ -695,7 +686,7 @@
 	return aarch32_opcode_cond_checks[cond](regs->pstate);
 }
 
-static void compat_cntfrq_read_handler(unsigned int esr, struct pt_regs *regs)
+static void compat_cntfrq_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int reg = (esr & ESR_ELx_CP15_32_ISS_RT_MASK) >> ESR_ELx_CP15_32_ISS_RT_SHIFT;
 
@@ -712,7 +703,7 @@
 	{},
 };
 
-static void compat_cntvct_read_handler(unsigned int esr, struct pt_regs *regs)
+static void compat_cntvct_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = (esr & ESR_ELx_CP15_64_ISS_RT_MASK) >> ESR_ELx_CP15_64_ISS_RT_SHIFT;
 	int rt2 = (esr & ESR_ELx_CP15_64_ISS_RT2_MASK) >> ESR_ELx_CP15_64_ISS_RT2_SHIFT;
@@ -732,7 +723,7 @@
 	{},
 };
 
-void do_cp15instr(unsigned int esr, struct pt_regs *regs)
+void do_el0_cp15(unsigned long esr, struct pt_regs *regs)
 {
 	const struct sys64_hook *hook, *hook_base;
 
@@ -753,7 +744,7 @@
 		hook_base = cp15_64_hooks;
 		break;
 	default:
-		do_undefinstr(regs);
+		do_el0_undef(regs, esr);
 		return;
 	}
 
@@ -768,12 +759,11 @@
 	 * EL0. Fall back to our usual undefined instruction handler
 	 * so that we handle these consistently.
 	 */
-	do_undefinstr(regs);
+	do_el0_undef(regs, esr);
 }
-NOKPROBE_SYMBOL(do_cp15instr);
 #endif
 
-void do_sysinstr(unsigned int esr, struct pt_regs *regs)
+void do_el0_sys(unsigned long esr, struct pt_regs *regs)
 {
 	const struct sys64_hook *hook;
 
@@ -788,9 +778,8 @@
 	 * back to our usual undefined instruction handler so that we handle
 	 * these consistently.
 	 */
-	do_undefinstr(regs);
+	do_el0_undef(regs, esr);
 }
-NOKPROBE_SYMBOL(do_sysinstr);
 
 static const char *esr_class_str[] = {
 	[0 ... ESR_ELx_EC_MAX]		= "UNRECOGNIZED EC",
@@ -837,7 +826,7 @@
 	[ESR_ELx_EC_BRK64]		= "BRK (AArch64)",
 };
 
-const char *esr_get_class_string(u32 esr)
+const char *esr_get_class_string(unsigned long esr)
 {
 	return esr_class_str[ESR_ELx_EC(esr)];
 }
@@ -846,7 +835,7 @@
  * bad_el0_sync handles unexpected, but potentially recoverable synchronous
  * exceptions taken from EL0.
  */
-void bad_el0_sync(struct pt_regs *regs, int reason, unsigned int esr)
+void bad_el0_sync(struct pt_regs *regs, int reason, unsigned long esr)
 {
 	unsigned long pc = instruction_pointer(regs);
 
@@ -862,7 +851,7 @@
 DEFINE_PER_CPU(unsigned long [OVERFLOW_STACK_SIZE/sizeof(long)], overflow_stack)
 	__aligned(16);
 
-void panic_bad_stack(struct pt_regs *regs, unsigned int esr, unsigned long far)
+void panic_bad_stack(struct pt_regs *regs, unsigned long esr, unsigned long far)
 {
 	unsigned long tsk_stk = (unsigned long)current->stack;
 	unsigned long irq_stk = (unsigned long)this_cpu_read(irq_stack_ptr);
@@ -871,7 +860,7 @@
 	console_verbose();
 	pr_emerg("Insufficient stack space to handle exception!");
 
-	pr_emerg("ESR: 0x%08x -- %s\n", esr, esr_get_class_string(esr));
+	pr_emerg("ESR: 0x%016lx -- %s\n", esr, esr_get_class_string(esr));
 	pr_emerg("FAR: 0x%016lx\n", far);
 
 	pr_emerg("Task stack:     [0x%016lx..0x%016lx]\n",
@@ -892,11 +881,11 @@
 }
 #endif
 
-void __noreturn arm64_serror_panic(struct pt_regs *regs, u32 esr)
+void __noreturn arm64_serror_panic(struct pt_regs *regs, unsigned long esr)
 {
 	console_verbose();
 
-	pr_crit("SError Interrupt on CPU%d, code 0x%08x -- %s\n",
+	pr_crit("SError Interrupt on CPU%d, code 0x%016lx -- %s\n",
 		smp_processor_id(), esr, esr_get_class_string(esr));
 	if (regs)
 		__show_regs(regs);
@@ -907,9 +896,9 @@
 	unreachable();
 }
 
-bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned int esr)
+bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned long esr)
 {
-	u32 aet = arm64_ras_serror_get_severity(esr);
+	unsigned long aet = arm64_ras_serror_get_severity(esr);
 
 	switch (aet) {
 	case ESR_ELx_AET_CE:	/* corrected error */
@@ -939,7 +928,7 @@
 	}
 }
 
-void do_serror(struct pt_regs *regs, unsigned int esr)
+void do_serror(struct pt_regs *regs, unsigned long esr)
 {
 	/* non-RAS errors are not containable */
 	if (!arm64_is_ras_serror(esr) || arm64_is_fatal_ras_serror(regs, esr))
@@ -960,11 +949,11 @@
 	return 1;
 }
 
-static int bug_handler(struct pt_regs *regs, unsigned int esr)
+static int bug_handler(struct pt_regs *regs, unsigned long esr)
 {
 	switch (report_bug(regs->pc, regs)) {
 	case BUG_TRAP_TYPE_BUG:
-		die("Oops - BUG", regs, 0);
+		die("Oops - BUG", regs, esr);
 		break;
 
 	case BUG_TRAP_TYPE_WARN:
@@ -985,10 +974,10 @@
 	.imm = BUG_BRK_IMM,
 };
 
-static int reserved_fault_handler(struct pt_regs *regs, unsigned int esr)
+static int reserved_fault_handler(struct pt_regs *regs, unsigned long esr)
 {
 	pr_err("%s generated an invalid instruction at %pS!\n",
-		in_bpf_jit(regs) ? "BPF JIT" : "Kernel text patching",
+		"Kernel text patching",
 		(void *)instruction_pointer(regs));
 
 	/* We cannot handle this */
@@ -1007,7 +996,7 @@
 #define KASAN_ESR_SIZE_MASK	0x0f
 #define KASAN_ESR_SIZE(esr)	(1 << ((esr) & KASAN_ESR_SIZE_MASK))
 
-static int kasan_handler(struct pt_regs *regs, unsigned int esr)
+static int kasan_handler(struct pt_regs *regs, unsigned long esr)
 {
 	bool recover = esr & KASAN_ESR_RECOVER;
 	bool write = esr & KASAN_ESR_WRITE;
@@ -1032,7 +1021,7 @@
 	 * This is something that might be fixed at some point in the future.
 	 */
 	if (!recover)
-		die("Oops - KASAN", regs, 0);
+		die("Oops - KASAN", regs, esr);
 
 	/* If thread survives, skip over the brk instruction and continue: */
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
@@ -1050,11 +1039,11 @@
  * Initial handler for AArch64 BRK exceptions
  * This handler only used until debug_traps_init().
  */
-int __init early_brk64(unsigned long addr, unsigned int esr,
+int __init early_brk64(unsigned long addr, unsigned long esr,
 		struct pt_regs *regs)
 {
 #ifdef CONFIG_KASAN_SW_TAGS
-	unsigned int comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
+	unsigned long comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
 
 	if ((comment & ~KASAN_BRK_MASK) == KASAN_BRK_IMM)
 		return kasan_handler(regs, esr) != DBG_HOOK_HANDLED;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/vdso.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/vdso.c
@@ -314,7 +314,7 @@
 
 	memcpy((void *)(vdso_page + 0x1000 - kuser_sz), __kuser_helper_start,
 	       kuser_sz);
-	aarch32_vectors_page = virt_to_page(vdso_page);
+	aarch32_vectors_page = virt_to_page((void *)vdso_page);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/vdso/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/vdso/Makefile
@@ -48,9 +48,6 @@
 targets += vdso.lds
 CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
 
-# Force dependency (incbin is bad)
-$(obj)/vdso.o : $(obj)/vdso.so
-
 # Link rule for the .so file, .lds has to be first
 $(obj)/vdso.so.dbg: $(obj)/vdso.lds $(obj-vdso) FORCE
 	$(call if_changed,vdsold_and_vdso_check)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/vdso/vdso.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/vdso/vdso.lds.S
@@ -37,6 +37,7 @@
 	 */
 	/DISCARD/	: {
 		*(.note.GNU-stack .note.gnu.property)
+		*(.ARM.attributes)
 	}
 	.note		: { *(.note.*) }		:text	:note
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/vdso32/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/vdso32/Makefile
@@ -10,18 +10,15 @@
 
 # Same as cc-*option, but using CC_COMPAT instead of CC
 ifeq ($(CONFIG_CC_IS_CLANG), y)
-CC_COMPAT_CLANG_FLAGS := --target=$(notdir $(CROSS_COMPILE_COMPAT:%-=%))
-
 CC_COMPAT ?= $(CC)
-CC_COMPAT += $(CC_COMPAT_CLANG_FLAGS)
-
-ifneq ($(LLVM),)
-LD_COMPAT ?= $(LD)
+CC_COMPAT += --target=arm-linux-gnueabi
 else
-LD_COMPAT ?= $(CROSS_COMPILE_COMPAT)ld
+CC_COMPAT ?= $(CROSS_COMPILE_COMPAT)gcc
 endif
+
+ifeq ($(CONFIG_LD_IS_LLD), y)
+LD_COMPAT ?= $(LD)
 else
-CC_COMPAT ?= $(CROSS_COMPILE_COMPAT)gcc
 LD_COMPAT ?= $(CROSS_COMPILE_COMPAT)ld
 endif
 
@@ -40,16 +37,13 @@
 # As a result we set our own flags here.
 
 # KBUILD_CPPFLAGS and NOSTDINC_FLAGS from top-level Makefile
-VDSO_CPPFLAGS := -DBUILD_VDSO -D__KERNEL__ -nostdinc -isystem $(shell $(CC_COMPAT) -print-file-name=include)
+VDSO_CPPFLAGS := -DBUILD_VDSO -D__KERNEL__ -nostdinc
+VDSO_CPPFLAGS += -isystem $(shell $(CC_COMPAT) -print-file-name=include 2>/dev/null)
 VDSO_CPPFLAGS += $(LINUXINCLUDE)
 
 # Common C and assembly flags
 # From top-level Makefile
 VDSO_CAFLAGS := $(VDSO_CPPFLAGS)
-ifneq ($(shell $(CC_COMPAT) --version 2>&1 | head -n 1 | grep clang),)
-VDSO_CAFLAGS += --target=$(notdir $(CROSS_COMPILE_COMPAT:%-=%))
-endif
-
 VDSO_CAFLAGS += $(call cc32-option,-fno-PIE)
 ifdef CONFIG_DEBUG_INFO
 VDSO_CAFLAGS += -g
@@ -150,9 +144,6 @@
 targets += vdso.lds
 CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
 
-# Force dependency (vdso.s includes vdso.so through incbin)
-$(obj)/vdso.o: $(obj)/vdso.so
-
 include/generated/vdso32-offsets.h: $(obj)/vdso.so.dbg FORCE
 	$(call if_changed,vdsosym)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kernel/vmlinux.lds.S
@@ -139,6 +139,7 @@
 	/DISCARD/ : {
 		*(.interp .dynamic)
 		*(.dynsym .dynstr .hash .gnu.hash)
+		*(.ARM.attributes)
 	}
 
 	. = KIMAGE_VADDR;
@@ -258,6 +259,9 @@
 	__initdata_end = .;
 	__init_end = .;
 
+	.data.rel.ro : { *(.data.rel.ro) }
+	ASSERT(SIZEOF(.data.rel.ro) == 0, "Unexpected RELRO detected!")
+
 	_data = .;
 	_sdata = .;
 	RW_DATA(L1_CACHE_BYTES, PAGE_SIZE, THREAD_ALIGN)
@@ -309,9 +313,6 @@
 		*(.plt) *(.plt.*) *(.iplt) *(.igot .igot.plt)
 	}
 	ASSERT(SIZEOF(.plt) == 0, "Unexpected run-time procedure linkages detected!")
-
-	.data.rel.ro : { *(.data.rel.ro) }
-	ASSERT(SIZEOF(.data.rel.ro) == 0, "Unexpected RELRO detected!")
 }
 
 #include "image-vars.h"
@@ -330,7 +331,7 @@
 	<= SZ_4K, "Hibernate exit text too big or misaligned")
 #endif
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-ASSERT((__entry_tramp_text_end - __entry_tramp_text_start) == PAGE_SIZE,
+ASSERT((__entry_tramp_text_end - __entry_tramp_text_start) <= 3*PAGE_SIZE,
 	"Entry trampoline text too big")
 #endif
 #ifdef CONFIG_KVM
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/arm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/arm.c
@@ -297,14 +297,6 @@
 	return vzalloc(sizeof(struct kvm));
 }
 
-void kvm_arch_free_vm(struct kvm *kvm)
-{
-	if (!has_vhe())
-		kfree(kvm);
-	else
-		vfree(kvm);
-}
-
 int kvm_arch_vcpu_precreate(struct kvm *kvm, unsigned int id)
 {
 	if (irqchip_in_kernel(kvm) && vgic_initialized(kvm))
@@ -356,7 +348,7 @@
 	kvm_mmu_free_memory_cache(&vcpu->arch.mmu_page_cache);
 	kvm_timer_vcpu_terminate(vcpu);
 	kvm_pmu_vcpu_destroy(vcpu);
-
+	kvm_vgic_vcpu_destroy(vcpu);
 	kvm_arm_vcpu_destroy(vcpu);
 }
 
@@ -379,13 +371,15 @@
 	 */
 	preempt_disable();
 	kvm_vgic_vmcr_sync(vcpu);
-	vgic_v4_put(vcpu, true);
+	vcpu->arch.flags |= KVM_ARM64_VCPU_IN_WFI;
+	vgic_v4_put(vcpu);
 	preempt_enable();
 }
 
 void kvm_arch_vcpu_unblocking(struct kvm_vcpu *vcpu)
 {
 	preempt_disable();
+	vcpu->arch.flags &= ~KVM_ARM64_VCPU_IN_WFI;
 	vgic_v4_load(vcpu);
 	preempt_enable();
 }
@@ -696,7 +690,7 @@
 		if (kvm_check_request(KVM_REQ_RELOAD_GICv4, vcpu)) {
 			/* The distributor enable bits were changed */
 			preempt_disable();
-			vgic_v4_put(vcpu, false);
+			vgic_v4_put(vcpu);
 			vgic_v4_load(vcpu);
 			preempt_enable();
 		}
@@ -712,8 +706,7 @@
 	if (likely(!vcpu_mode_is_32bit(vcpu)))
 		return false;
 
-	return !system_supports_32bit_el0() ||
-		static_branch_unlikely(&arm64_mismatched_32bit_el0);
+	return !kvm_supports_32bit_el0();
 }
 
 /**
@@ -755,6 +748,24 @@
 			xfer_to_guest_mode_work_pending();
 }
 
+/*
+ * Actually run the vCPU, entering an RCU extended quiescent state (EQS) while
+ * the vCPU is running.
+ *
+ * This must be noinstr as instrumentation may make use of RCU, and this is not
+ * safe during the EQS.
+ */
+static int noinstr kvm_arm_vcpu_enter_exit(struct kvm_vcpu *vcpu)
+{
+	int ret;
+
+	guest_state_enter_irqoff();
+	ret = kvm_call_hyp_ret(__kvm_vcpu_run, vcpu);
+	guest_state_exit_irqoff();
+
+	return ret;
+}
+
 /**
  * kvm_arch_vcpu_ioctl_run - the main VCPU run function to execute guest code
  * @vcpu:	The VCPU pointer
@@ -845,9 +856,9 @@
 		 * Enter the guest
 		 */
 		trace_kvm_entry(*vcpu_pc(vcpu));
-		guest_enter_irqoff();
+		guest_timing_enter_irqoff();
 
-		ret = kvm_call_hyp_ret(__kvm_vcpu_run, vcpu);
+		ret = kvm_arm_vcpu_enter_exit(vcpu);
 
 		vcpu->mode = OUTSIDE_GUEST_MODE;
 		vcpu->stat.exits++;
@@ -882,26 +893,23 @@
 		kvm_arch_vcpu_ctxsync_fp(vcpu);
 
 		/*
-		 * We may have taken a host interrupt in HYP mode (ie
-		 * while executing the guest). This interrupt is still
-		 * pending, as we haven't serviced it yet!
+		 * We must ensure that any pending interrupts are taken before
+		 * we exit guest timing so that timer ticks are accounted as
+		 * guest time. Transiently unmask interrupts so that any
+		 * pending interrupts are taken.
 		 *
-		 * We're now back in SVC mode, with interrupts
-		 * disabled.  Enabling the interrupts now will have
-		 * the effect of taking the interrupt again, in SVC
-		 * mode this time.
+		 * Per ARM DDI 0487G.b section D1.13.4, an ISB (or other
+		 * context synchronization event) is necessary to ensure that
+		 * pending interrupts are taken.
 		 */
 		local_irq_enable();
+		isb();
+		local_irq_disable();
+
+		guest_timing_exit_irqoff();
+
+		local_irq_enable();
 
-		/*
-		 * We do local_irq_enable() before calling guest_exit() so
-		 * that if a timer interrupt hits while running the guest we
-		 * account that tick as being spent in the guest.  We enable
-		 * preemption after calling guest_exit() so that if we get
-		 * preempted we make sure ticks after that is not counted as
-		 * guest time.
-		 */
-		guest_exit();
 		trace_kvm_exit(ret, kvm_vcpu_trap_get_class(vcpu), *vcpu_pc(vcpu));
 
 		/* Exit types that need handling before we can be preempted */
@@ -1443,10 +1451,8 @@
 	base = kern_hyp_va(kvm_ksym_ref(__bp_harden_hyp_vecs));
 	kvm_init_vector_slot(base, HYP_VECTOR_SPECTRE_DIRECT);
 
-	if (!cpus_have_const_cap(ARM64_SPECTRE_V3A))
-		return 0;
-
-	if (!has_vhe()) {
+	if (kvm_system_needs_idmapped_vectors() &&
+	    !is_protected_kvm_enabled()) {
 		err = create_hyp_exec_mappings(__pa_symbol(__bp_harden_hyp_vecs),
 					       __BP_HARDEN_HYP_VECS_SZ, &base);
 		if (err)
@@ -1971,31 +1977,50 @@
 	return err;
 }
 
-static void _kvm_host_prot_finalize(void *discard)
+static void _kvm_host_prot_finalize(void *arg)
 {
-	WARN_ON(kvm_call_hyp_nvhe(__pkvm_prot_finalize));
+	int *err = arg;
+
+	if (WARN_ON(kvm_call_hyp_nvhe(__pkvm_prot_finalize)))
+		WRITE_ONCE(*err, -EINVAL);
 }
 
-static int finalize_hyp_mode(void)
+static int pkvm_drop_host_privileges(void)
 {
-	if (!is_protected_kvm_enabled())
-		return 0;
-
-	/*
-	 * Exclude HYP BSS from kmemleak so that it doesn't get peeked
-	 * at, which would end badly once the section is inaccessible.
-	 * None of other sections should ever be introspected.
-	 */
-	kmemleak_free_part(__hyp_bss_start, __hyp_bss_end - __hyp_bss_start);
+	int ret = 0;
 
 	/*
 	 * Flip the static key upfront as that may no longer be possible
 	 * once the host stage 2 is installed.
 	 */
 	static_branch_enable(&kvm_protected_mode_initialized);
-	on_each_cpu(_kvm_host_prot_finalize, NULL, 1);
 
-	return 0;
+	/*
+	 * Fixup the boot mode so that we don't take spurious round
+	 * trips via EL2 on cpu_resume. Flush to the PoC for a good
+	 * measure, so that it can be observed by a CPU coming out of
+	 * suspend with the MMU off.
+	 */
+	__boot_cpu_mode[0] = __boot_cpu_mode[1] = BOOT_CPU_MODE_EL1;
+	dcache_clean_poc((unsigned long)__boot_cpu_mode,
+			 (unsigned long)(__boot_cpu_mode + 2));
+
+	on_each_cpu(_kvm_host_prot_finalize, &ret, 1);
+	return ret;
+}
+
+static int finalize_hyp_mode(void)
+{
+	if (!is_protected_kvm_enabled())
+		return 0;
+
+	/*
+	 * Exclude HYP sections from kmemleak so that they don't get peeked
+	 * at, which would end badly once inaccessible.
+	 */
+	kmemleak_free_part(__hyp_bss_start, __hyp_bss_end - __hyp_bss_start);
+	kmemleak_free_part(__va(hyp_mem_base), hyp_mem_size);
+	return pkvm_drop_host_privileges();
 }
 
 struct kvm_vcpu *kvm_mpidr_to_vcpu(struct kvm *kvm, unsigned long mpidr)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/guest.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/guest.c
@@ -242,7 +242,7 @@
 		u64 mode = (*(u64 *)valp) & PSR_AA32_MODE_MASK;
 		switch (mode) {
 		case PSR_AA32_MODE_USR:
-			if (!system_supports_32bit_el0())
+			if (!kvm_supports_32bit_el0())
 				return -EINVAL;
 			break;
 		case PSR_AA32_MODE_FIQ:
@@ -250,6 +250,7 @@
 		case PSR_AA32_MODE_SVC:
 		case PSR_AA32_MODE_ABT:
 		case PSR_AA32_MODE_UND:
+		case PSR_AA32_MODE_SYS:
 			if (!vcpu_el1_is_32bit(vcpu))
 				return -EINVAL;
 			break;
@@ -270,7 +271,7 @@
 	if (*vcpu_cpsr(vcpu) & PSR_MODE32_BIT) {
 		int i, nr_reg;
 
-		switch (*vcpu_cpsr(vcpu)) {
+		switch (*vcpu_cpsr(vcpu) & PSR_AA32_MODE_MASK) {
 		/*
 		 * Either we are dealing with user mode, and only the
 		 * first 15 registers (+ PC) must be narrowed to 32bit.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/handle_exit.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/handle_exit.c
@@ -226,6 +226,14 @@
 {
 	struct kvm_run *run = vcpu->run;
 
+	if (ARM_SERROR_PENDING(exception_index)) {
+		/*
+		 * The SError is handled by handle_exit_early(). If the guest
+		 * survives it will re-execute the original instruction.
+		 */
+		return 1;
+	}
+
 	exception_index = ARM_EXCEPTION_CODE(exception_index);
 
 	switch (exception_index) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/exception.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/exception.c
@@ -13,6 +13,7 @@
 #include <hyp/adjust_pc.h>
 #include <linux/kvm_host.h>
 #include <asm/kvm_emulate.h>
+#include <asm/kvm_mmu.h>
 
 #if !defined (__KVM_NVHE_HYPERVISOR__) && !defined (__KVM_VHE_HYPERVISOR__)
 #error Hypervisor code only!
@@ -38,7 +39,10 @@
 
 static void __vcpu_write_spsr(struct kvm_vcpu *vcpu, u64 val)
 {
-	write_sysreg_el1(val, SYS_SPSR);
+	if (has_vhe())
+		write_sysreg_el1(val, SYS_SPSR);
+	else
+		__vcpu_sys_reg(vcpu, SPSR_EL1) = val;
 }
 
 static void __vcpu_write_spsr_abt(struct kvm_vcpu *vcpu, u64 val)
@@ -112,7 +116,7 @@
 	new |= (old & PSR_C_BIT);
 	new |= (old & PSR_V_BIT);
 
-	if (kvm_has_mte(vcpu->kvm))
+	if (kvm_has_mte(kern_hyp_va(vcpu->kvm)))
 		new |= PSR_TCO_BIT;
 
 	new |= (old & PSR_DIT_BIT);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/hyp-entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/hyp-entry.S
@@ -44,7 +44,7 @@
 el1_sync:				// Guest trapped into EL2
 
 	mrs	x0, esr_el2
-	lsr	x0, x0, #ESR_ELx_EC_SHIFT
+	ubfx	x0, x0, #ESR_ELx_EC_SHIFT, #ESR_ELx_EC_WIDTH
 	cmp	x0, #ESR_ELx_EC_HVC64
 	ccmp	x0, #ESR_ELx_EC_HVC32, #4, ne
 	b.ne	el1_trap
@@ -62,6 +62,10 @@
 	/* ARM_SMCCC_ARCH_WORKAROUND_2 handling */
 	eor	w1, w1, #(ARM_SMCCC_ARCH_WORKAROUND_1 ^ \
 			  ARM_SMCCC_ARCH_WORKAROUND_2)
+	cbz	w1, wa_epilogue
+
+	eor	w1, w1, #(ARM_SMCCC_ARCH_WORKAROUND_2 ^ \
+			  ARM_SMCCC_ARCH_WORKAROUND_3)
 	cbnz	w1, el1_trap
 
 wa_epilogue:
@@ -192,7 +196,10 @@
 	sub	sp, sp, #(8 * 4)
 	stp	x2, x3, [sp, #(8 * 0)]
 	stp	x0, x1, [sp, #(8 * 2)]
+	alternative_cb spectre_bhb_patch_wa3
+	/* Patched to mov WA3 when supported */
 	mov	w0, #ARM_SMCCC_ARCH_WORKAROUND_1
+	alternative_cb_end
 	smc	#0
 	ldp	x2, x3, [sp, #(8 * 0)]
 	add	sp, sp, #(8 * 2)
@@ -205,6 +212,8 @@
 	spectrev2_smccc_wa1_smc
 	.else
 	stp	x0, x1, [sp, #-16]!
+	mitigate_spectre_bhb_loop	x0
+	mitigate_spectre_bhb_clear_insn
 	.endif
 	.if \indirect != 0
 	alternative_cb  kvm_patch_vector_branch
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/include/hyp/switch.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/include/hyp/switch.h
@@ -416,10 +416,17 @@
  */
 static inline bool fixup_guest_exit(struct kvm_vcpu *vcpu, u64 *exit_code)
 {
+	/*
+	 * Save PSTATE early so that we can evaluate the vcpu mode
+	 * early on.
+	 */
+	vcpu->arch.ctxt.regs.pstate = read_sysreg_el2(SYS_SPSR);
+
 	if (ARM_EXCEPTION_CODE(*exit_code) != ARM_EXCEPTION_IRQ)
 		vcpu->arch.fault.esr_el2 = read_sysreg_el2(SYS_ESR);
 
-	if (ARM_SERROR_PENDING(*exit_code)) {
+	if (ARM_SERROR_PENDING(*exit_code) &&
+	    ARM_EXCEPTION_CODE(*exit_code) != ARM_EXCEPTION_IRQ) {
 		u8 esr_ec = kvm_vcpu_trap_get_class(vcpu);
 
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/include/hyp/sysreg-sr.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/include/hyp/sysreg-sr.h
@@ -70,7 +70,12 @@
 static inline void __sysreg_save_el2_return_state(struct kvm_cpu_context *ctxt)
 {
 	ctxt->regs.pc			= read_sysreg_el2(SYS_ELR);
-	ctxt->regs.pstate		= read_sysreg_el2(SYS_SPSR);
+	/*
+	 * Guest PSTATE gets saved at guest fixup time in all
+	 * cases. We still need to handle the nVHE host side here.
+	 */
+	if (!has_vhe() && ctxt->__hyp_running_vcpu)
+		ctxt->regs.pstate	= read_sysreg_el2(SYS_SPSR);
 
 	if (cpus_have_final_cap(ARM64_HAS_RAS_EXTN))
 		ctxt_sys_reg(ctxt, DISR_EL1) = read_sysreg_s(SYS_VDISR_EL2);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/nvhe/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/nvhe/Makefile
@@ -83,6 +83,10 @@
 # Remove ftrace, Shadow Call Stack, and CFI CFLAGS.
 # This is equivalent to the 'notrace', '__noscs', and '__nocfi' annotations.
 KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_FTRACE) $(CC_FLAGS_SCS) $(CC_FLAGS_CFI), $(KBUILD_CFLAGS))
+# Starting from 13.0.0 llvm emits SHT_REL section '.llvm.call-graph-profile'
+# when profile optimization is applied. gen-hyprel does not support SHT_REL and
+# causes a build failure. Remove profile optimization flags.
+KBUILD_CFLAGS := $(filter-out -fprofile-sample-use=% -fprofile-use=%, $(KBUILD_CFLAGS))
 
 # KVM nVHE code is run at a different exception code with a different map, so
 # compiler instrumentation that inserts callbacks or checks into the code may
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/nvhe/host.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/nvhe/host.S
@@ -115,7 +115,7 @@
 .L__vect_start\@:
 	stp	x0, x1, [sp, #-16]!
 	mrs	x0, esr_el2
-	lsr	x0, x0, #ESR_ELx_EC_SHIFT
+	ubfx	x0, x0, #ESR_ELx_EC_SHIFT, #ESR_ELx_EC_WIDTH
 	cmp	x0, #ESR_ELx_EC_HVC64
 	b.ne	__host_exit
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/nvhe/mm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/nvhe/mm.c
@@ -146,8 +146,10 @@
 	phys_addr_t phys;
 	void *bp_base;
 
-	if (!cpus_have_const_cap(ARM64_SPECTRE_V3A))
+	if (!kvm_system_needs_idmapped_vectors()) {
+		__hyp_bp_vect_base = __bp_harden_hyp_vecs;
 		return 0;
+	}
 
 	phys = __hyp_pa(__bp_harden_hyp_vecs);
 	bp_base = (void *)__pkvm_create_private_mapping(phys,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/nvhe/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/nvhe/setup.c
@@ -177,7 +177,7 @@
 
 	phys = kvm_pte_to_phys(pte);
 	if (!addr_is_memory(phys))
-		return 0;
+		return -EINVAL;
 
 	/*
 	 * Adjust the host stage-2 mappings to match the ownership attributes
@@ -206,8 +206,18 @@
 		.cb	= finalize_host_mappings_walker,
 		.flags	= KVM_PGTABLE_WALK_LEAF,
 	};
+	int i, ret;
+
+	for (i = 0; i < hyp_memblock_nr; i++) {
+		struct memblock_region *reg = &hyp_memory[i];
+		u64 start = (u64)hyp_phys_to_virt(reg->base);
+
+		ret = kvm_pgtable_walk(&pkvm_pgtable, start, reg->size, &walker);
+		if (ret)
+			return ret;
+	}
 
-	return kvm_pgtable_walk(&pkvm_pgtable, 0, BIT(pkvm_pgtable.ia_bits), &walker);
+	return 0;
 }
 
 void __noreturn __pkvm_init_finalise(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/nvhe/switch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/nvhe/switch.c
@@ -279,5 +279,5 @@
 
 asmlinkage void kvm_unexpected_el2_exception(void)
 {
-	return __kvm_unexpected_el2_exception();
+	__kvm_unexpected_el2_exception();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/pgtable.c
@@ -921,13 +921,9 @@
 	 */
 	stage2_put_pte(ptep, mmu, addr, level, mm_ops);
 
-	if (need_flush) {
-		kvm_pte_t *pte_follow = kvm_pte_follow(pte, mm_ops);
-
-		dcache_clean_inval_poc((unsigned long)pte_follow,
-				    (unsigned long)pte_follow +
-					    kvm_granule_size(level));
-	}
+	if (need_flush && mm_ops->dcache_clean_inval_poc)
+		mm_ops->dcache_clean_inval_poc(kvm_pte_follow(pte, mm_ops),
+					       kvm_granule_size(level));
 
 	if (childp)
 		mm_ops->put_page(childp);
@@ -1089,15 +1085,13 @@
 	struct kvm_pgtable *pgt = arg;
 	struct kvm_pgtable_mm_ops *mm_ops = pgt->mm_ops;
 	kvm_pte_t pte = *ptep;
-	kvm_pte_t *pte_follow;
 
 	if (!kvm_pte_valid(pte) || !stage2_pte_cacheable(pgt, pte))
 		return 0;
 
-	pte_follow = kvm_pte_follow(pte, mm_ops);
-	dcache_clean_inval_poc((unsigned long)pte_follow,
-			    (unsigned long)pte_follow +
-				    kvm_granule_size(level));
+	if (mm_ops->dcache_clean_inval_poc)
+		mm_ops->dcache_clean_inval_poc(kvm_pte_follow(pte, mm_ops),
+					       kvm_granule_size(level));
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hyp/vhe/switch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hyp/vhe/switch.c
@@ -10,6 +10,7 @@
 #include <linux/kvm_host.h>
 #include <linux/types.h>
 #include <linux/jump_label.h>
+#include <linux/percpu.h>
 #include <uapi/linux/psci.h>
 
 #include <kvm/arm_psci.h>
@@ -25,6 +26,7 @@
 #include <asm/debug-monitors.h>
 #include <asm/processor.h>
 #include <asm/thread_info.h>
+#include <asm/vectors.h>
 
 /* VHE specific context */
 DEFINE_PER_CPU(struct kvm_host_data, kvm_host_data);
@@ -68,7 +70,7 @@
 
 static void __deactivate_traps(struct kvm_vcpu *vcpu)
 {
-	extern char vectors[];	/* kernel exception vectors */
+	const char *host_vectors = vectors;
 
 	___deactivate_traps(vcpu);
 
@@ -82,7 +84,10 @@
 	asm(ALTERNATIVE("nop", "isb", ARM64_WORKAROUND_SPECULATIVE_AT));
 
 	write_sysreg(CPACR_EL1_DEFAULT, cpacr_el1);
-	write_sysreg(vectors, vbar_el1);
+
+	if (!arm64_kernel_unmapped_at_el0())
+		host_vectors = __this_cpu_read(this_cpu_vector);
+	write_sysreg(host_vectors, vbar_el1);
 }
 NOKPROBE_SYMBOL(__deactivate_traps);
 
@@ -215,5 +220,5 @@
 
 asmlinkage void kvm_unexpected_el2_exception(void)
 {
-	return __kvm_unexpected_el2_exception();
+	__kvm_unexpected_el2_exception();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/hypercalls.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/hypercalls.c
@@ -107,6 +107,18 @@
 				break;
 			}
 			break;
+		case ARM_SMCCC_ARCH_WORKAROUND_3:
+			switch (arm64_get_spectre_bhb_state()) {
+			case SPECTRE_VULNERABLE:
+				break;
+			case SPECTRE_MITIGATED:
+				val[0] = SMCCC_RET_SUCCESS;
+				break;
+			case SPECTRE_UNAFFECTED:
+				val[0] = SMCCC_ARCH_WORKAROUND_RET_UNAFFECTED;
+				break;
+			}
+			break;
 		case ARM_SMCCC_HV_PV_TIME_FEATURES:
 			val[0] = SMCCC_RET_SUCCESS;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/mmu.c
@@ -31,6 +31,13 @@
 
 static unsigned long io_map_base;
 
+static phys_addr_t stage2_range_addr_end(phys_addr_t addr, phys_addr_t end)
+{
+	phys_addr_t size = kvm_granule_size(KVM_PGTABLE_MIN_BLOCK_LEVEL);
+	phys_addr_t boundary = ALIGN_DOWN(addr + size, size);
+
+	return (boundary - 1 < end - 1) ? boundary : end;
+}
 
 /*
  * Release kvm_mmu_lock periodically if the memory region is large. Otherwise,
@@ -52,7 +59,7 @@
 		if (!pgt)
 			return -EINVAL;
 
-		next = stage2_pgd_addr_end(kvm, addr, end);
+		next = stage2_range_addr_end(addr, end);
 		ret = fn(pgt, addr, next - addr);
 		if (ret)
 			break;
@@ -468,14 +475,33 @@
 				   CONFIG_PGTABLE_LEVELS),
 		.mm_ops		= &kvm_user_mm_ops,
 	};
+	unsigned long flags;
 	kvm_pte_t pte = 0;	/* Keep GCC quiet... */
 	u32 level = ~0;
 	int ret;
 
+	/*
+	 * Disable IRQs so that we hazard against a concurrent
+	 * teardown of the userspace page tables (which relies on
+	 * IPI-ing threads).
+	 */
+	local_irq_save(flags);
 	ret = kvm_pgtable_get_leaf(&pgt, addr, &pte, &level);
-	VM_BUG_ON(ret);
-	VM_BUG_ON(level >= KVM_PGTABLE_MAX_LEVELS);
-	VM_BUG_ON(!(pte & PTE_VALID));
+	local_irq_restore(flags);
+
+	if (ret)
+		return ret;
+
+	/*
+	 * Not seeing an error, but not updating level? Something went
+	 * deeply wrong...
+	 */
+	if (WARN_ON(level >= KVM_PGTABLE_MAX_LEVELS))
+		return -EFAULT;
+
+	/* Oops, the userspace PTs are gone... Replay the fault */
+	if (!kvm_pte_valid(pte))
+		return -EAGAIN;
 
 	return BIT(ARM64_HW_PGTABLE_LEVEL_SHIFT(level));
 }
@@ -826,7 +852,7 @@
  *
  * Returns the size of the mapping.
  */
-static unsigned long
+static long
 transparent_hugepage_adjust(struct kvm *kvm, struct kvm_memory_slot *memslot,
 			    unsigned long hva, kvm_pfn_t *pfnp,
 			    phys_addr_t *ipap)
@@ -838,8 +864,15 @@
 	 * sure that the HVA and IPA are sufficiently aligned and that the
 	 * block map is contained within the memslot.
 	 */
-	if (fault_supports_stage2_huge_mapping(memslot, hva, PMD_SIZE) &&
-	    get_user_mapping_size(kvm, hva) >= PMD_SIZE) {
+	if (fault_supports_stage2_huge_mapping(memslot, hva, PMD_SIZE)) {
+		int sz = get_user_mapping_size(kvm, hva);
+
+		if (sz < 0)
+			return sz;
+
+		if (sz < PMD_SIZE)
+			return PAGE_SIZE;
+
 		/*
 		 * The address we faulted on is backed by a transparent huge
 		 * page.  However, because we map the compound huge page and
@@ -957,7 +990,7 @@
 	kvm_pfn_t pfn;
 	bool logging_active = memslot_is_logging(memslot);
 	unsigned long fault_level = kvm_vcpu_trap_get_fault_level(vcpu);
-	unsigned long vma_pagesize, fault_granule;
+	long vma_pagesize, fault_granule;
 	enum kvm_pgtable_prot prot = KVM_PGTABLE_PROT_R;
 	struct kvm_pgtable *pgt;
 
@@ -972,6 +1005,20 @@
 	}
 
 	/*
+	 * Permission faults just need to update the existing leaf entry,
+	 * and so normally don't require allocations from the memcache. The
+	 * only exception to this is when dirty logging is enabled at runtime
+	 * and a write fault needs to collapse a block entry into a table.
+	 */
+	if (fault_status != FSC_PERM ||
+	    (logging_active && write_fault)) {
+		ret = kvm_mmu_topup_memory_cache(memcache,
+						 kvm_mmu_cache_min_pages(kvm));
+		if (ret)
+			return ret;
+	}
+
+	/*
 	 * Let's check if we will get back a huge page backed by hugetlbfs, or
 	 * get block mapping for device MMIO region.
 	 */
@@ -1025,36 +1072,17 @@
 		fault_ipa &= ~(vma_pagesize - 1);
 
 	gfn = fault_ipa >> PAGE_SHIFT;
-	mmap_read_unlock(current->mm);
 
 	/*
-	 * Permission faults just need to update the existing leaf entry,
-	 * and so normally don't require allocations from the memcache. The
-	 * only exception to this is when dirty logging is enabled at runtime
-	 * and a write fault needs to collapse a block entry into a table.
-	 */
-	if (fault_status != FSC_PERM || (logging_active && write_fault)) {
-		ret = kvm_mmu_topup_memory_cache(memcache,
-						 kvm_mmu_cache_min_pages(kvm));
-		if (ret)
-			return ret;
-	}
-
-	mmu_seq = vcpu->kvm->mmu_notifier_seq;
-	/*
-	 * Ensure the read of mmu_notifier_seq happens before we call
-	 * gfn_to_pfn_prot (which calls get_user_pages), so that we don't risk
-	 * the page we just got a reference to gets unmapped before we have a
-	 * chance to grab the mmu_lock, which ensure that if the page gets
-	 * unmapped afterwards, the call to kvm_unmap_gfn will take it away
-	 * from us again properly. This smp_rmb() interacts with the smp_wmb()
-	 * in kvm_mmu_notifier_invalidate_<page|range_end>.
+	 * Read mmu_notifier_seq so that KVM can detect if the results of
+	 * vma_lookup() or __gfn_to_pfn_memslot() become stale prior to
+	 * acquiring kvm->mmu_lock.
 	 *
-	 * Besides, __gfn_to_pfn_memslot() instead of gfn_to_pfn_prot() is
-	 * used to avoid unnecessary overhead introduced to locate the memory
-	 * slot because it's always fixed even @gfn is adjusted for huge pages.
+	 * Rely on mmap_read_unlock() for an implicit smp_rmb(), which pairs
+	 * with the smp_wmb() in kvm_dec_notifier_count().
 	 */
-	smp_rmb();
+	mmu_seq = vcpu->kvm->mmu_notifier_seq;
+	mmap_read_unlock(current->mm);
 
 	pfn = __gfn_to_pfn_memslot(memslot, gfn, false, NULL,
 				   write_fault, &writable, NULL);
@@ -1104,6 +1132,11 @@
 			vma_pagesize = transparent_hugepage_adjust(kvm, memslot,
 								   hva, &pfn,
 								   &fault_ipa);
+
+		if (vma_pagesize < 0) {
+			ret = vma_pagesize;
+			goto out_unlock;
+		}
 	}
 
 	if (fault_status != FSC_PERM && !device && kvm_has_mte(kvm)) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/pmu-emul.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/pmu-emul.c
@@ -371,7 +371,6 @@
 
 	if ((__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E)) {
 		reg = __vcpu_sys_reg(vcpu, PMOVSSET_EL0);
-		reg &= __vcpu_sys_reg(vcpu, PMCNTENSET_EL0);
 		reg &= __vcpu_sys_reg(vcpu, PMINTENSET_EL1);
 	}
 
@@ -554,6 +553,7 @@
 			__vcpu_sys_reg(vcpu, PMOVSSET_EL0) |= BIT(i);
 		}
 	}
+	kvm_vcpu_pmu_restore_guest(vcpu);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/psci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/psci.c
@@ -406,7 +406,7 @@
 
 int kvm_arm_get_fw_num_regs(struct kvm_vcpu *vcpu)
 {
-	return 3;		/* PSCI version and two workaround registers */
+	return 4;		/* PSCI version and three workaround registers */
 }
 
 int kvm_arm_copy_fw_reg_indices(struct kvm_vcpu *vcpu, u64 __user *uindices)
@@ -420,6 +420,9 @@
 	if (put_user(KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2, uindices++))
 		return -EFAULT;
 
+	if (put_user(KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3, uindices++))
+		return -EFAULT;
+
 	return 0;
 }
 
@@ -459,6 +462,17 @@
 		case SPECTRE_VULNERABLE:
 			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
 		}
+		break;
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3:
+		switch (arm64_get_spectre_bhb_state()) {
+		case SPECTRE_VULNERABLE:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_AVAIL;
+		case SPECTRE_MITIGATED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_AVAIL;
+		case SPECTRE_UNAFFECTED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_REQUIRED;
+		}
+		return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_AVAIL;
 	}
 
 	return -EINVAL;
@@ -475,6 +489,7 @@
 		break;
 	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
 	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3:
 		val = get_kernel_wa_level(reg->id) & KVM_REG_FEATURE_LEVEL_MASK;
 		break;
 	default:
@@ -493,6 +508,8 @@
 	u64 val;
 	int wa_level;
 
+	if (KVM_REG_SIZE(reg->id) != sizeof(val))
+		return -ENOENT;
 	if (copy_from_user(&val, uaddr, KVM_REG_SIZE(reg->id)))
 		return -EFAULT;
 
@@ -520,6 +537,7 @@
 	}
 
 	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3:
 		if (val & ~KVM_REG_FEATURE_LEVEL_MASK)
 			return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/sys_regs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/sys_regs.c
@@ -30,6 +30,7 @@
 #include <trace/events/kvm.h>
 
 #include "sys_regs.h"
+#include "vgic/vgic.h"
 
 #include "trace.h"
 
@@ -203,6 +204,11 @@
 {
 	bool g1;
 
+	if (!kvm_has_gicv3(vcpu->kvm)) {
+		kvm_inject_undefined(vcpu);
+		return false;
+	}
+
 	if (!p->is_write)
 		return read_from_write_only(vcpu, p, r);
 
@@ -649,7 +655,7 @@
 	 */
 	val = ((pmcr & ~ARMV8_PMU_PMCR_MASK)
 	       | (ARMV8_PMU_PMCR_MASK & 0xdecafbad)) & (~ARMV8_PMU_PMCR_E);
-	if (!system_supports_32bit_el0())
+	if (!kvm_supports_32bit_el0())
 		val |= ARMV8_PMU_PMCR_LC;
 	__vcpu_sys_reg(vcpu, r->reg) = val;
 }
@@ -698,11 +704,10 @@
 		val = __vcpu_sys_reg(vcpu, PMCR_EL0);
 		val &= ~ARMV8_PMU_PMCR_MASK;
 		val |= p->regval & ARMV8_PMU_PMCR_MASK;
-		if (!system_supports_32bit_el0())
+		if (!kvm_supports_32bit_el0())
 			val |= ARMV8_PMU_PMCR_LC;
 		__vcpu_sys_reg(vcpu, PMCR_EL0) = val;
 		kvm_pmu_handle_pmcr(vcpu, val);
-		kvm_vcpu_pmu_restore_guest(vcpu);
 	} else {
 		/* PMCR.P & PMCR.C are RAZ */
 		val = __vcpu_sys_reg(vcpu, PMCR_EL0)
@@ -1518,7 +1523,7 @@
 	/* CRm=6 */
 	ID_SANITISED(ID_AA64ISAR0_EL1),
 	ID_SANITISED(ID_AA64ISAR1_EL1),
-	ID_UNALLOCATED(6,2),
+	ID_SANITISED(ID_AA64ISAR2_EL1),
 	ID_UNALLOCATED(6,3),
 	ID_UNALLOCATED(6,4),
 	ID_UNALLOCATED(6,5),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/trace_arm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/trace_arm.h
@@ -2,6 +2,7 @@
 #if !defined(_TRACE_ARM_ARM64_KVM_H) || defined(TRACE_HEADER_MULTI_READ)
 #define _TRACE_ARM_ARM64_KVM_H
 
+#include <asm/kvm_arm.h>
 #include <kvm/arm_arch_timer.h>
 #include <linux/tracepoint.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-init.c
@@ -363,7 +363,10 @@
 	vgic_flush_pending_lpis(vcpu);
 
 	INIT_LIST_HEAD(&vgic_cpu->ap_list_head);
-	vgic_cpu->rd_iodev.base_addr = VGIC_ADDR_UNDEF;
+	if (vcpu->kvm->arch.vgic.vgic_model == KVM_DEV_TYPE_ARM_VGIC_V3) {
+		vgic_unregister_redist_iodev(vcpu);
+		vgic_cpu->rd_iodev.base_addr = VGIC_ADDR_UNDEF;
+	}
 }
 
 /* To be called with kvm->lock held */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-its.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-its.c
@@ -462,6 +462,9 @@
 		}
 
 		irq = vgic_get_irq(vcpu->kvm, NULL, intids[i]);
+		if (!irq)
+			continue;
+
 		raw_spin_lock_irqsave(&irq->irq_lock, flags);
 		irq->pending_latch = pendmask & (1U << bit_nr);
 		vgic_queue_irq_unlock(vcpu->kvm, irq, flags);
@@ -584,7 +587,11 @@
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&dist->lpi_list_lock, flags);
+
 	irq = __vgic_its_check_cache(dist, db, devid, eventid);
+	if (irq)
+		vgic_get_irq_kref(irq);
+
 	raw_spin_unlock_irqrestore(&dist->lpi_list_lock, flags);
 
 	return irq;
@@ -763,6 +770,7 @@
 	raw_spin_lock_irqsave(&irq->irq_lock, flags);
 	irq->pending_latch = true;
 	vgic_queue_irq_unlock(kvm, irq, flags);
+	vgic_put_irq(kvm, irq);
 
 	return 0;
 }
@@ -847,6 +855,9 @@
 
 	ite = find_ite(its, device_id, event_id);
 	if (ite && its_is_collection_mapped(ite->collection)) {
+		struct its_device *device = find_its_device(its, device_id);
+		int ite_esz = vgic_its_get_abi(its)->ite_esz;
+		gpa_t gpa = device->itt_addr + ite->event_id * ite_esz;
 		/*
 		 * Though the spec talks about removing the pending state, we
 		 * don't bother here since we clear the ITTE anyway and the
@@ -855,7 +866,8 @@
 		vgic_its_invalidate_cache(kvm);
 
 		its_free_ite(kvm, ite);
-		return 0;
+
+		return vgic_its_write_entry_lock(its, gpa, 0, ite_esz);
 	}
 
 	return E_ITS_DISCARD_UNMAPPED_INTERRUPT;
@@ -1174,9 +1186,11 @@
 	bool valid = its_cmd_get_validbit(its_cmd);
 	u8 num_eventid_bits = its_cmd_get_size(its_cmd);
 	gpa_t itt_addr = its_cmd_get_ittaddr(its_cmd);
+	int dte_esz = vgic_its_get_abi(its)->dte_esz;
 	struct its_device *device;
+	gpa_t gpa;
 
-	if (!vgic_its_check_id(its, its->baser_device_table, device_id, NULL))
+	if (!vgic_its_check_id(its, its->baser_device_table, device_id, &gpa))
 		return E_ITS_MAPD_DEVICE_OOR;
 
 	if (valid && num_eventid_bits > VITS_TYPER_IDBITS)
@@ -1197,7 +1211,7 @@
 	 * is an error, so we are done in any case.
 	 */
 	if (!valid)
-		return 0;
+		return vgic_its_write_entry_lock(its, gpa, 0, dte_esz);
 
 	device = vgic_its_alloc_device(its, device_id, itt_addr,
 				       num_eventid_bits);
@@ -1369,6 +1383,8 @@
 
 	for (i = 0; i < irq_count; i++) {
 		irq = vgic_get_irq(kvm, NULL, intids[i]);
+		if (!irq)
+			continue;
 
 		update_affinity(irq, vcpu2);
 
@@ -2096,7 +2112,7 @@
 
 	memset(entry, 0, esz);
 
-	while (len > 0) {
+	while (true) {
 		int next_offset;
 		size_t byte_offset;
 
@@ -2109,6 +2125,9 @@
 			return next_offset;
 
 		byte_offset = next_offset * esz;
+		if (byte_offset >= len)
+			break;
+
 		id += next_offset;
 		gpa += byte_offset;
 		len -= byte_offset;
@@ -2122,7 +2141,6 @@
 static int vgic_its_save_ite(struct vgic_its *its, struct its_device *dev,
 			      struct its_ite *ite, gpa_t gpa, int ite_esz)
 {
-	struct kvm *kvm = its->dev->kvm;
 	u32 next_offset;
 	u64 val;
 
@@ -2131,7 +2149,8 @@
 	       ((u64)ite->irq->intid << KVM_ITS_ITE_PINTID_SHIFT) |
 		ite->collection->collection_id;
 	val = cpu_to_le64(val);
-	return kvm_write_guest_lock(kvm, gpa, &val, ite_esz);
+
+	return vgic_its_write_entry_lock(its, gpa, val, ite_esz);
 }
 
 /**
@@ -2267,7 +2286,6 @@
 static int vgic_its_save_dte(struct vgic_its *its, struct its_device *dev,
 			     gpa_t ptr, int dte_esz)
 {
-	struct kvm *kvm = its->dev->kvm;
 	u64 val, itt_addr_field;
 	u32 next_offset;
 
@@ -2278,7 +2296,8 @@
 	       (itt_addr_field << KVM_ITS_DTE_ITTADDR_SHIFT) |
 		(dev->num_eventid_bits - 1));
 	val = cpu_to_le64(val);
-	return kvm_write_guest_lock(kvm, ptr, &val, dte_esz);
+
+	return vgic_its_write_entry_lock(its, ptr, val, dte_esz);
 }
 
 /**
@@ -2458,7 +2477,8 @@
 	       ((u64)collection->target_addr << KVM_ITS_CTE_RDBASE_SHIFT) |
 	       collection->collection_id);
 	val = cpu_to_le64(val);
-	return kvm_write_guest_lock(its->dev->kvm, gpa, &val, esz);
+
+	return vgic_its_write_entry_lock(its, gpa, val, esz);
 }
 
 static int vgic_its_restore_cte(struct vgic_its *its, gpa_t gpa, int esz)
@@ -2469,8 +2489,7 @@
 	u64 val;
 	int ret;
 
-	BUG_ON(esz > sizeof(val));
-	ret = kvm_read_guest_lock(kvm, gpa, &val, esz);
+	ret = vgic_its_read_entry_lock(its, gpa, &val, esz);
 	if (ret)
 		return ret;
 	val = le64_to_cpu(val);
@@ -2504,7 +2523,6 @@
 	u64 baser = its->baser_coll_table;
 	gpa_t gpa = GITS_BASER_ADDR_48_to_52(baser);
 	struct its_collection *collection;
-	u64 val;
 	size_t max_size, filled = 0;
 	int ret, cte_esz = abi->cte_esz;
 
@@ -2528,10 +2546,7 @@
 	 * table is not fully filled, add a last dummy element
 	 * with valid bit unset
 	 */
-	val = 0;
-	BUG_ON(cte_esz > sizeof(val));
-	ret = kvm_write_guest_lock(its->dev->kvm, gpa, &val, cte_esz);
-	return ret;
+	return vgic_its_write_entry_lock(its, gpa, 0, cte_esz);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-kvm-device.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-kvm-device.c
@@ -284,16 +284,12 @@
 int vgic_v2_parse_attr(struct kvm_device *dev, struct kvm_device_attr *attr,
 		       struct vgic_reg_attr *reg_attr)
 {
-	int cpuid;
+	int cpuid = FIELD_GET(KVM_DEV_ARM_VGIC_CPUID_MASK, attr->attr);
 
-	cpuid = (attr->attr & KVM_DEV_ARM_VGIC_CPUID_MASK) >>
-		 KVM_DEV_ARM_VGIC_CPUID_SHIFT;
-
-	if (cpuid >= atomic_read(&dev->kvm->online_vcpus))
-		return -EINVAL;
-
-	reg_attr->vcpu = kvm_get_vcpu(dev->kvm, cpuid);
 	reg_attr->addr = attr->attr & KVM_DEV_ARM_VGIC_OFFSET_MASK;
+	reg_attr->vcpu = kvm_get_vcpu_by_id(dev->kvm, cpuid);
+	if (!reg_attr->vcpu)
+		return -EINVAL;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-mmio-v2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-mmio-v2.c
@@ -418,11 +418,11 @@
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ(GIC_DIST_PENDING_SET,
 		vgic_mmio_read_pending, vgic_mmio_write_spending,
-		NULL, vgic_uaccess_write_spending, 1,
+		vgic_uaccess_read_pending, vgic_uaccess_write_spending, 1,
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ(GIC_DIST_PENDING_CLEAR,
 		vgic_mmio_read_pending, vgic_mmio_write_cpending,
-		NULL, vgic_uaccess_write_cpending, 1,
+		vgic_uaccess_read_pending, vgic_uaccess_write_cpending, 1,
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ(GIC_DIST_ACTIVE_SET,
 		vgic_mmio_read_active, vgic_mmio_write_sactive,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-mmio-v3.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-mmio-v3.c
@@ -363,19 +363,26 @@
 		struct vgic_irq *irq = vgic_get_irq(vcpu->kvm, vcpu, intid + i);
 
 		raw_spin_lock_irqsave(&irq->irq_lock, flags);
-		if (test_bit(i, &val)) {
-			/*
-			 * pending_latch is set irrespective of irq type
-			 * (level or edge) to avoid dependency that VM should
-			 * restore irq config before pending info.
-			 */
-			irq->pending_latch = true;
-			vgic_queue_irq_unlock(vcpu->kvm, irq, flags);
-		} else {
+
+		/*
+		 * pending_latch is set irrespective of irq type
+		 * (level or edge) to avoid dependency that VM should
+		 * restore irq config before pending info.
+		 */
+		irq->pending_latch = test_bit(i, &val);
+
+		if (irq->hw && vgic_irq_is_sgi(irq->intid)) {
+			irq_set_irqchip_state(irq->host_irq,
+					      IRQCHIP_STATE_PENDING,
+					      irq->pending_latch);
 			irq->pending_latch = false;
-			raw_spin_unlock_irqrestore(&irq->irq_lock, flags);
 		}
 
+		if (irq->pending_latch)
+			vgic_queue_irq_unlock(vcpu->kvm, irq, flags);
+		else
+			raw_spin_unlock_irqrestore(&irq->irq_lock, flags);
+
 		vgic_put_irq(vcpu->kvm, irq);
 	}
 
@@ -744,7 +751,7 @@
 	return 0;
 }
 
-static void vgic_unregister_redist_iodev(struct kvm_vcpu *vcpu)
+void vgic_unregister_redist_iodev(struct kvm_vcpu *vcpu)
 {
 	struct vgic_io_device *rd_dev = &vcpu->arch.vgic_cpu.rd_iodev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-mmio.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-mmio.c
@@ -226,8 +226,9 @@
 	return 0;
 }
 
-unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
-				     gpa_t addr, unsigned int len)
+static unsigned long __read_pending(struct kvm_vcpu *vcpu,
+				    gpa_t addr, unsigned int len,
+				    bool is_user)
 {
 	u32 intid = VGIC_ADDR_TO_INTID(addr, 1);
 	u32 value = 0;
@@ -248,6 +249,8 @@
 						    IRQCHIP_STATE_PENDING,
 						    &val);
 			WARN_RATELIMIT(err, "IRQ %d", irq->host_irq);
+		} else if (!is_user && vgic_irq_is_mapped_level(irq)) {
+			val = vgic_get_phys_line_level(irq);
 		} else {
 			val = irq_is_pending(irq);
 		}
@@ -261,6 +264,18 @@
 	return value;
 }
 
+unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
+				     gpa_t addr, unsigned int len)
+{
+	return __read_pending(vcpu, addr, len, false);
+}
+
+unsigned long vgic_uaccess_read_pending(struct kvm_vcpu *vcpu,
+					gpa_t addr, unsigned int len)
+{
+	return __read_pending(vcpu, addr, len, true);
+}
+
 static bool is_vgic_v2_sgi(struct kvm_vcpu *vcpu, struct vgic_irq *irq)
 {
 	return (vgic_irq_is_sgi(irq->intid) &&
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-mmio.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-mmio.h
@@ -149,6 +149,9 @@
 unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
 				     gpa_t addr, unsigned int len);
 
+unsigned long vgic_uaccess_read_pending(struct kvm_vcpu *vcpu,
+					gpa_t addr, unsigned int len);
+
 void vgic_mmio_write_spending(struct kvm_vcpu *vcpu,
 			      gpa_t addr, unsigned int len,
 			      unsigned long val);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-v3.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-v3.c
@@ -347,26 +347,23 @@
  * The deactivation of the doorbell interrupt will trigger the
  * unmapping of the associated vPE.
  */
-static void unmap_all_vpes(struct vgic_dist *dist)
+static void unmap_all_vpes(struct kvm *kvm)
 {
-	struct irq_desc *desc;
+	struct vgic_dist *dist = &kvm->arch.vgic;
 	int i;
 
-	for (i = 0; i < dist->its_vm.nr_vpes; i++) {
-		desc = irq_to_desc(dist->its_vm.vpes[i]->irq);
-		irq_domain_deactivate_irq(irq_desc_get_irq_data(desc));
-	}
+	for (i = 0; i < dist->its_vm.nr_vpes; i++)
+		free_irq(dist->its_vm.vpes[i]->irq, kvm_get_vcpu(kvm, i));
 }
 
-static void map_all_vpes(struct vgic_dist *dist)
+static void map_all_vpes(struct kvm *kvm)
 {
-	struct irq_desc *desc;
+	struct vgic_dist *dist = &kvm->arch.vgic;
 	int i;
 
-	for (i = 0; i < dist->its_vm.nr_vpes; i++) {
-		desc = irq_to_desc(dist->its_vm.vpes[i]->irq);
-		irq_domain_activate_irq(irq_desc_get_irq_data(desc), false);
-	}
+	for (i = 0; i < dist->its_vm.nr_vpes; i++)
+		WARN_ON(vgic_v4_request_vpe_irq(kvm_get_vcpu(kvm, i),
+						dist->its_vm.vpes[i]->irq));
 }
 
 /**
@@ -391,7 +388,7 @@
 	 * and enabling of the doorbells have already been done.
 	 */
 	if (kvm_vgic_global_state.has_gicv4_1) {
-		unmap_all_vpes(dist);
+		unmap_all_vpes(kvm);
 		vlpi_avail = true;
 	}
 
@@ -441,7 +438,7 @@
 
 out:
 	if (vlpi_avail)
-		map_all_vpes(dist);
+		map_all_vpes(kvm);
 
 	return ret;
 }
@@ -718,7 +715,7 @@
 {
 	struct vgic_v3_cpu_if *cpu_if = &vcpu->arch.vgic_cpu.vgic_v3;
 
-	WARN_ON(vgic_v4_put(vcpu, false));
+	WARN_ON(vgic_v4_put(vcpu));
 
 	vgic_v3_vmcr_sync(vcpu);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic-v4.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic-v4.c
@@ -222,6 +222,11 @@
 	*val = !!(*ptr & mask);
 }
 
+int vgic_v4_request_vpe_irq(struct kvm_vcpu *vcpu, int irq)
+{
+	return request_irq(irq, vgic_v4_doorbell_handler, 0, "vcpu", vcpu);
+}
+
 /**
  * vgic_v4_init - Initialize the GICv4 data structures
  * @kvm:	Pointer to the VM being initialized
@@ -282,8 +287,7 @@
 			irq_flags &= ~IRQ_NOAUTOEN;
 		irq_set_status_flags(irq, irq_flags);
 
-		ret = request_irq(irq, vgic_v4_doorbell_handler,
-				  0, "vcpu", vcpu);
+		ret = vgic_v4_request_vpe_irq(vcpu, irq);
 		if (ret) {
 			kvm_err("failed to allocate vcpu IRQ%d\n", irq);
 			/*
@@ -329,14 +333,15 @@
 	its_vm->vpes = NULL;
 }
 
-int vgic_v4_put(struct kvm_vcpu *vcpu, bool need_db)
+int vgic_v4_put(struct kvm_vcpu *vcpu)
 {
 	struct its_vpe *vpe = &vcpu->arch.vgic_cpu.vgic_v3.its_vpe;
 
 	if (!vgic_supports_direct_msis(vcpu->kvm) || !vpe->resident)
 		return 0;
 
-	return its_make_vpe_non_resident(vpe, need_db);
+	return its_make_vpe_non_resident(vpe,
+			vcpu->arch.flags & KVM_ARM64_VCPU_IN_WFI);
 }
 
 int vgic_v4_load(struct kvm_vcpu *vcpu)
@@ -347,6 +352,9 @@
 	if (!vgic_supports_direct_msis(vcpu->kvm) || vpe->resident)
 		return 0;
 
+	if (vcpu->arch.flags & KVM_ARM64_VCPU_IN_WFI)
+		return 0;
+
 	/*
 	 * Before making the VPE resident, make sure the redistributor
 	 * corresponding to our current CPU expects us here. See the
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/kvm/vgic/vgic.h
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/kvm/vgic/vgic.h
@@ -6,6 +6,7 @@
 #define __KVM_ARM_VGIC_NEW_H__
 
 #include <linux/irqchip/arm-gic-common.h>
+#include <asm/kvm_mmu.h>
 
 #define PRODUCT_ID_KVM		0x4b	/* ASCII code K */
 #define IMPLEMENTER_ARM		0x43b
@@ -126,6 +127,29 @@
 	return vgic_irq_get_lr_count(irq) > 1;
 }
 
+static inline int vgic_its_read_entry_lock(struct vgic_its *its, gpa_t eaddr,
+					   u64 *eval, unsigned long esize)
+{
+	struct kvm *kvm = its->dev->kvm;
+
+	if (KVM_BUG_ON(esize != sizeof(*eval), kvm))
+		return -EINVAL;
+
+	return kvm_read_guest_lock(kvm, eaddr, eval, esize);
+
+}
+
+static inline int vgic_its_write_entry_lock(struct vgic_its *its, gpa_t eaddr,
+					    u64 eval, unsigned long esize)
+{
+	struct kvm *kvm = its->dev->kvm;
+
+	if (KVM_BUG_ON(esize != sizeof(eval), kvm))
+		return -EINVAL;
+
+	return kvm_write_guest_lock(kvm, eaddr, &eval, esize);
+}
+
 /*
  * This struct provides an intermediate representation of the fields contained
  * in the GICH_VMCR and ICH_VMCR registers, such that code exporting the GIC
@@ -223,6 +247,7 @@
 int vgic_v3_save_pending_tables(struct kvm *kvm);
 int vgic_v3_set_redist_base(struct kvm *kvm, u32 index, u64 addr, u32 count);
 int vgic_register_redist_iodev(struct kvm_vcpu *vcpu);
+void vgic_unregister_redist_iodev(struct kvm_vcpu *vcpu);
 bool vgic_v3_check_base(struct kvm *kvm);
 
 void vgic_v3_load(struct kvm_vcpu *vcpu);
@@ -321,5 +346,13 @@
 void vgic_v4_teardown(struct kvm *kvm);
 void vgic_v4_configure_vsgis(struct kvm *kvm);
 void vgic_v4_get_vlpi_state(struct vgic_irq *irq, bool *val);
+int vgic_v4_request_vpe_irq(struct kvm_vcpu *vcpu, int irq);
+
+static inline bool kvm_has_gicv3(struct kvm *kvm)
+{
+	return (static_branch_unlikely(&kvm_vgic_global_state.gicv3_cpuif) &&
+		irqchip_in_kernel(kvm) &&
+		kvm->arch.vgic.vgic_model == KVM_DEV_TYPE_ARM_VGIC_V3);
+}
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/lib/clear_page.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/lib/clear_page.S
@@ -16,6 +16,7 @@
  */
 SYM_FUNC_START_PI(clear_page)
 	mrs	x1, dczid_el0
+	tbnz	x1, #4, 2f	/* Branch if DC ZVA is prohibited */
 	and	w1, w1, #0xf
 	mov	x2, #4
 	lsl	x1, x2, x1
@@ -25,5 +26,14 @@
 	tst	x0, #(PAGE_SIZE - 1)
 	b.ne	1b
 	ret
+
+2:	stnp	xzr, xzr, [x0]
+	stnp	xzr, xzr, [x0, #16]
+	stnp	xzr, xzr, [x0, #32]
+	stnp	xzr, xzr, [x0, #48]
+	add	x0, x0, #64
+	tst	x0, #(PAGE_SIZE - 1)
+	b.ne	2b
+	ret
 SYM_FUNC_END_PI(clear_page)
 EXPORT_SYMBOL(clear_page)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/lib/csum.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/lib/csum.c
@@ -24,7 +24,7 @@
 	const u64 *ptr;
 	u64 data, sum64 = 0;
 
-	if (unlikely(len == 0))
+	if (unlikely(len <= 0))
 		return 0;
 
 	offset = (unsigned long)buff & 7;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/lib/mte.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/lib/mte.S
@@ -43,17 +43,23 @@
  *	x0 - address to the beginning of the page
  */
 SYM_FUNC_START(mte_zero_clear_page_tags)
+	and	x0, x0, #(1 << MTE_TAG_SHIFT) - 1	// clear the tag
 	mrs	x1, dczid_el0
+	tbnz	x1, #4, 2f	// Branch if DC GZVA is prohibited
 	and	w1, w1, #0xf
 	mov	x2, #4
 	lsl	x1, x2, x1
-	and	x0, x0, #(1 << MTE_TAG_SHIFT) - 1	// clear the tag
 
 1:	dc	gzva, x0
 	add	x0, x0, x1
 	tst	x0, #(PAGE_SIZE - 1)
 	b.ne	1b
 	ret
+
+2:	stz2g	x0, [x0], #(MTE_GRANULE_SIZE * 2)
+	tst	x0, #(PAGE_SIZE - 1)
+	b.ne	2b
+	ret
 SYM_FUNC_END(mte_zero_clear_page_tags)
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/lib/strncmp.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/lib/strncmp.S
@@ -1,9 +1,9 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- * Copyright (c) 2013-2021, Arm Limited.
+ * Copyright (c) 2013-2022, Arm Limited.
  *
  * Adapted from the original at:
- * https://github.com/ARM-software/optimized-routines/blob/e823e3abf5f89ecb/string/aarch64/strncmp.S
+ * https://github.com/ARM-software/optimized-routines/blob/189dfefe37d54c5b/string/aarch64/strncmp.S
  */
 
 #include <linux/linkage.h>
@@ -11,14 +11,14 @@
 
 /* Assumptions:
  *
- * ARMv8-a, AArch64
+ * ARMv8-a, AArch64.
+ * MTE compatible.
  */
 
 #define L(label) .L ## label
 
 #define REP8_01 0x0101010101010101
 #define REP8_7f 0x7f7f7f7f7f7f7f7f
-#define REP8_80 0x8080808080808080
 
 /* Parameters and result.  */
 #define src1		x0
@@ -39,10 +39,24 @@
 #define tmp3		x10
 #define zeroones	x11
 #define pos		x12
-#define limit_wd	x13
-#define mask		x14
-#define endloop		x15
+#define mask		x13
+#define endloop		x14
 #define count		mask
+#define offset		pos
+#define neg_offset	x15
+
+/* Define endian dependent shift operations.
+   On big-endian early bytes are at MSB and on little-endian LSB.
+   LS_FW means shifting towards early bytes.
+   LS_BK means shifting towards later bytes.
+   */
+#ifdef __AARCH64EB__
+#define LS_FW lsl
+#define LS_BK lsr
+#else
+#define LS_FW lsr
+#define LS_BK lsl
+#endif
 
 SYM_FUNC_START_WEAK_PI(strncmp)
 	cbz	limit, L(ret0)
@@ -52,9 +66,6 @@
 	and	count, src1, #7
 	b.ne	L(misaligned8)
 	cbnz	count, L(mutual_align)
-	/* Calculate the number of full and partial words -1.  */
-	sub	limit_wd, limit, #1	/* limit != 0, so no underflow.  */
-	lsr	limit_wd, limit_wd, #3	/* Convert to Dwords.  */
 
 	/* NUL detection works on the principle that (X - 1) & (~X) & 0x80
 	   (=> (X - 1) & ~(X | 0x7f)) is non-zero iff a byte is zero, and
@@ -64,56 +75,52 @@
 	ldr	data1, [src1], #8
 	ldr	data2, [src2], #8
 L(start_realigned):
-	subs	limit_wd, limit_wd, #1
+	subs	limit, limit, #8
 	sub	tmp1, data1, zeroones
 	orr	tmp2, data1, #REP8_7f
 	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	csinv	endloop, diff, xzr, pl	/* Last Dword or differences.  */
+	csinv	endloop, diff, xzr, hi	/* Last Dword or differences.  */
 	bics	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
 	ccmp	endloop, #0, #0, eq
 	b.eq	L(loop_aligned)
 	/* End of main loop */
 
-	/* Not reached the limit, must have found the end or a diff.  */
-	tbz	limit_wd, #63, L(not_limit)
-
-	/* Limit % 8 == 0 => all bytes significant.  */
-	ands	limit, limit, #7
-	b.eq	L(not_limit)
-
-	lsl	limit, limit, #3	/* Bits -> bytes.  */
-	mov	mask, #~0
-#ifdef __AARCH64EB__
-	lsr	mask, mask, limit
-#else
-	lsl	mask, mask, limit
-#endif
-	bic	data1, data1, mask
-	bic	data2, data2, mask
-
-	/* Make sure that the NUL byte is marked in the syndrome.  */
-	orr	has_nul, has_nul, mask
-
-L(not_limit):
+L(full_check):
+#ifndef __AARCH64EB__
 	orr	syndrome, diff, has_nul
-
-#ifndef	__AARCH64EB__
+	add	limit, limit, 8	/* Rewind limit to before last subs. */
+L(syndrome_check):
+	/* Limit was reached. Check if the NUL byte or the difference
+	   is before the limit. */
 	rev	syndrome, syndrome
 	rev	data1, data1
-	/* The MS-non-zero bit of the syndrome marks either the first bit
-	   that is different, or the top bit of the first zero byte.
-	   Shifting left now will bring the critical information into the
-	   top bits.  */
 	clz	pos, syndrome
 	rev	data2, data2
 	lsl	data1, data1, pos
+	cmp	limit, pos, lsr #3
 	lsl	data2, data2, pos
 	/* But we need to zero-extend (char is unsigned) the value and then
 	   perform a signed 32-bit subtraction.  */
 	lsr	data1, data1, #56
 	sub	result, data1, data2, lsr #56
+	csel result, result, xzr, hi
 	ret
 #else
+	/* Not reached the limit, must have found the end or a diff.  */
+	tbz	limit, #63, L(not_limit)
+	add	tmp1, limit, 8
+	cbz	limit, L(not_limit)
+
+	lsl	limit, tmp1, #3	/* Bits -> bytes.  */
+	mov	mask, #~0
+	lsr	mask, mask, limit
+	bic	data1, data1, mask
+	bic	data2, data2, mask
+
+	/* Make sure that the NUL byte is marked in the syndrome.  */
+	orr	has_nul, has_nul, mask
+
+L(not_limit):
 	/* For big-endian we cannot use the trick with the syndrome value
 	   as carry-propagation can corrupt the upper bits if the trailing
 	   bytes in the string contain 0x01.  */
@@ -134,10 +141,11 @@
 	rev	has_nul, has_nul
 	orr	syndrome, diff, has_nul
 	clz	pos, syndrome
-	/* The MS-non-zero bit of the syndrome marks either the first bit
-	   that is different, or the top bit of the first zero byte.
+	/* The most-significant-non-zero bit of the syndrome marks either the
+	   first bit that is different, or the top bit of the first zero byte.
 	   Shifting left now will bring the critical information into the
 	   top bits.  */
+L(end_quick):
 	lsl	data1, data1, pos
 	lsl	data2, data2, pos
 	/* But we need to zero-extend (char is unsigned) the value and then
@@ -159,22 +167,12 @@
 	neg	tmp3, count, lsl #3	/* 64 - bits(bytes beyond align). */
 	ldr	data2, [src2], #8
 	mov	tmp2, #~0
-	sub	limit_wd, limit, #1	/* limit != 0, so no underflow.  */
-#ifdef __AARCH64EB__
-	/* Big-endian.  Early bytes are at MSB.  */
-	lsl	tmp2, tmp2, tmp3	/* Shift (count & 63).  */
-#else
-	/* Little-endian.  Early bytes are at LSB.  */
-	lsr	tmp2, tmp2, tmp3	/* Shift (count & 63).  */
-#endif
-	and	tmp3, limit_wd, #7
-	lsr	limit_wd, limit_wd, #3
-	/* Adjust the limit. Only low 3 bits used, so overflow irrelevant.  */
-	add	limit, limit, count
-	add	tmp3, tmp3, count
+	LS_FW	tmp2, tmp2, tmp3	/* Shift (count & 63).  */
+	/* Adjust the limit and ensure it doesn't overflow.  */
+	adds	limit, limit, count
+	csinv	limit, limit, xzr, lo
 	orr	data1, data1, tmp2
 	orr	data2, data2, tmp2
-	add	limit_wd, limit_wd, tmp3, lsr #3
 	b	L(start_realigned)
 
 	.p2align 4
@@ -197,13 +195,11 @@
 	/* Align the SRC1 to a dword by doing a bytewise compare and then do
 	   the dword loop.  */
 L(try_misaligned_words):
-	lsr	limit_wd, limit, #3
-	cbz	count, L(do_misaligned)
+	cbz	count, L(src1_aligned)
 
 	neg	count, count
 	and	count, count, #7
 	sub	limit, limit, count
-	lsr	limit_wd, limit, #3
 
 L(page_end_loop):
 	ldrb	data1w, [src1], #1
@@ -214,48 +210,100 @@
 	subs	count, count, #1
 	b.hi	L(page_end_loop)
 
-L(do_misaligned):
-	/* Prepare ourselves for the next page crossing.  Unlike the aligned
-	   loop, we fetch 1 less dword because we risk crossing bounds on
-	   SRC2.  */
-	mov	count, #8
-	subs	limit_wd, limit_wd, #1
-	b.lo	L(done_loop)
+	/* The following diagram explains the comparison of misaligned strings.
+	   The bytes are shown in natural order. For little-endian, it is
+	   reversed in the registers. The "x" bytes are before the string.
+	   The "|" separates data that is loaded at one time.
+	   src1     | a a a a a a a a | b b b c c c c c | . . .
+	   src2     | x x x x x a a a   a a a a a b b b | c c c c c . . .
+
+	   After shifting in each step, the data looks like this:
+	                STEP_A              STEP_B              STEP_C
+	   data1    a a a a a a a a     b b b c c c c c     b b b c c c c c
+	   data2    a a a a a a a a     b b b 0 0 0 0 0     0 0 0 c c c c c
+
+	   The bytes with "0" are eliminated from the syndrome via mask.
+
+	   Align SRC2 down to 16 bytes. This way we can read 16 bytes at a
+	   time from SRC2. The comparison happens in 3 steps. After each step
+	   the loop can exit, or read from SRC1 or SRC2. */
+L(src1_aligned):
+	/* Calculate offset from 8 byte alignment to string start in bits. No
+	   need to mask offset since shifts are ignoring upper bits. */
+	lsl	offset, src2, #3
+	bic	src2, src2, #0xf
+	mov	mask, -1
+	neg	neg_offset, offset
+	ldr	data1, [src1], #8
+	ldp	tmp1, tmp2, [src2], #16
+	LS_BK	mask, mask, neg_offset
+	and	neg_offset, neg_offset, #63	/* Need actual value for cmp later. */
+	/* Skip the first compare if data in tmp1 is irrelevant. */
+	tbnz	offset, 6, L(misaligned_mid_loop)
+
 L(loop_misaligned):
-	and	tmp2, src2, #0xff8
-	eor	tmp2, tmp2, #0xff8
-	cbz	tmp2, L(page_end_loop)
+	/* STEP_A: Compare full 8 bytes when there is enough data from SRC2.*/
+	LS_FW	data2, tmp1, offset
+	LS_BK	tmp1, tmp2, neg_offset
+	subs	limit, limit, #8
+	orr	data2, data2, tmp1	/* 8 bytes from SRC2 combined from two regs.*/
+	sub	has_nul, data1, zeroones
+	eor	diff, data1, data2	/* Non-zero if differences found.  */
+	orr	tmp3, data1, #REP8_7f
+	csinv	endloop, diff, xzr, hi	/* If limit, set to all ones. */
+	bic	has_nul, has_nul, tmp3	/* Non-zero if NUL byte found in SRC1. */
+	orr	tmp3, endloop, has_nul
+	cbnz	tmp3, L(full_check)
 
 	ldr	data1, [src1], #8
-	ldr	data2, [src2], #8
-	sub	tmp1, data1, zeroones
-	orr	tmp2, data1, #REP8_7f
-	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	bics	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
-	ccmp	diff, #0, #0, eq
-	b.ne	L(not_limit)
-	subs	limit_wd, limit_wd, #1
-	b.pl	L(loop_misaligned)
-
-L(done_loop):
-	/* We found a difference or a NULL before the limit was reached.  */
-	and	limit, limit, #7
-	cbz	limit, L(not_limit)
-	/* Read the last word.  */
-	sub	src1, src1, 8
-	sub	src2, src2, 8
-	ldr	data1, [src1, limit]
-	ldr	data2, [src2, limit]
-	sub	tmp1, data1, zeroones
-	orr	tmp2, data1, #REP8_7f
-	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	bics	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
-	ccmp	diff, #0, #0, eq
-	b.ne	L(not_limit)
+L(misaligned_mid_loop):
+	/* STEP_B: Compare first part of data1 to second part of tmp2. */
+	LS_FW	data2, tmp2, offset
+#ifdef __AARCH64EB__
+	/* For big-endian we do a byte reverse to avoid carry-propagation
+	problem described above. This way we can reuse the has_nul in the
+	next step and also use syndrome value trick at the end. */
+	rev	tmp3, data1
+	#define data1_fixed tmp3
+#else
+	#define data1_fixed data1
+#endif
+	sub	has_nul, data1_fixed, zeroones
+	orr	tmp3, data1_fixed, #REP8_7f
+	eor	diff, data2, data1	/* Non-zero if differences found.  */
+	bic	has_nul, has_nul, tmp3	/* Non-zero if NUL terminator.  */
+#ifdef __AARCH64EB__
+	rev	has_nul, has_nul
+#endif
+	cmp	limit, neg_offset, lsr #3
+	orr	syndrome, diff, has_nul
+	bic	syndrome, syndrome, mask	/* Ignore later bytes. */
+	csinv	tmp3, syndrome, xzr, hi	/* If limit, set to all ones. */
+	cbnz	tmp3, L(syndrome_check)
+
+	/* STEP_C: Compare second part of data1 to first part of tmp1. */
+	ldp	tmp1, tmp2, [src2], #16
+	cmp	limit, #8
+	LS_BK	data2, tmp1, neg_offset
+	eor	diff, data2, data1	/* Non-zero if differences found.  */
+	orr	syndrome, diff, has_nul
+	and	syndrome, syndrome, mask	/* Ignore earlier bytes. */
+	csinv	tmp3, syndrome, xzr, hi	/* If limit, set to all ones. */
+	cbnz	tmp3, L(syndrome_check)
+
+	ldr	data1, [src1], #8
+	sub	limit, limit, #8
+	b	L(loop_misaligned)
+
+#ifdef	__AARCH64EB__
+L(syndrome_check):
+	clz	pos, syndrome
+	cmp	pos, limit, lsl #3
+	b.lo	L(end_quick)
+#endif
 
 L(ret0):
 	mov	result, #0
 	ret
-
 SYM_FUNC_END_PI(strncmp)
 EXPORT_SYMBOL_NOHWKASAN(strncmp)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/cache.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/cache.S
@@ -231,8 +231,6 @@
  */
 SYM_FUNC_START_PI(__dma_map_area)
 	add	x1, x0, x1
-	cmp	w2, #DMA_FROM_DEVICE
-	b.eq	__dma_inv_area
 	b	__dma_clean_area
 SYM_FUNC_END_PI(__dma_map_area)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/context.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/context.c
@@ -32,11 +32,11 @@
 static unsigned long *pinned_asid_map;
 
 #define ASID_MASK		(~GENMASK(asid_bits - 1, 0))
-#define ASID_FIRST_VERSION	(1UL << asid_bits)
+#define ASID_FIRST_VERSION	(1UL << 16)
 
-#define NUM_USER_ASIDS		ASID_FIRST_VERSION
-#define asid2idx(asid)		((asid) & ~ASID_MASK)
-#define idx2asid(idx)		asid2idx(idx)
+#define NUM_USER_ASIDS		(1UL << asid_bits)
+#define ctxid2asid(asid)	((asid) & ~ASID_MASK)
+#define asid2ctxid(asid, genid)	((asid) | (genid))
 
 /* Get the ASIDBits supported by the current CPU */
 static u32 get_cpu_asid_bits(void)
@@ -120,7 +120,7 @@
 		 */
 		if (asid == 0)
 			asid = per_cpu(reserved_asids, i);
-		__set_bit(asid2idx(asid), asid_map);
+		__set_bit(ctxid2asid(asid), asid_map);
 		per_cpu(reserved_asids, i) = asid;
 	}
 
@@ -162,7 +162,7 @@
 	u64 generation = atomic64_read(&asid_generation);
 
 	if (asid != 0) {
-		u64 newasid = generation | (asid & ~ASID_MASK);
+		u64 newasid = asid2ctxid(ctxid2asid(asid), generation);
 
 		/*
 		 * If our current ASID was active during a rollover, we
@@ -183,7 +183,7 @@
 		 * We had a valid ASID in a previous life, so try to re-use
 		 * it if possible.
 		 */
-		if (!__test_and_set_bit(asid2idx(asid), asid_map))
+		if (!__test_and_set_bit(ctxid2asid(asid), asid_map))
 			return newasid;
 	}
 
@@ -209,7 +209,7 @@
 set_asid:
 	__set_bit(asid, asid_map);
 	cur_idx = asid;
-	return idx2asid(asid) | generation;
+	return asid2ctxid(asid, generation);
 }
 
 void check_and_switch_context(struct mm_struct *mm)
@@ -300,13 +300,13 @@
 	}
 
 	nr_pinned_asids++;
-	__set_bit(asid2idx(asid), pinned_asid_map);
+	__set_bit(ctxid2asid(asid), pinned_asid_map);
 	refcount_set(&mm->context.pinned, 1);
 
 out_unlock:
 	raw_spin_unlock_irqrestore(&cpu_asid_lock, flags);
 
-	asid &= ~ASID_MASK;
+	asid = ctxid2asid(asid);
 
 	/* Set the equivalent of USER_ASID_BIT */
 	if (asid && arm64_kernel_unmapped_at_el0())
@@ -327,7 +327,7 @@
 	raw_spin_lock_irqsave(&cpu_asid_lock, flags);
 
 	if (refcount_dec_and_test(&mm->context.pinned)) {
-		__clear_bit(asid2idx(asid), pinned_asid_map);
+		__clear_bit(ctxid2asid(asid), pinned_asid_map);
 		nr_pinned_asids--;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/copypage.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/copypage.c
@@ -16,14 +16,15 @@
 
 void copy_highpage(struct page *to, struct page *from)
 {
-	struct page *kto = page_address(to);
-	struct page *kfrom = page_address(from);
+	void *kto = page_address(to);
+	void *kfrom = page_address(from);
 
 	copy_page(kto, kfrom);
 
+	page_kasan_tag_reset(to);
+
 	if (system_supports_mte() && test_bit(PG_mte_tagged, &from->flags)) {
 		set_bit(PG_mte_tagged, &to->flags);
-		page_kasan_tag_reset(to);
 		/*
 		 * We need smp_wmb() in between setting the flags and clearing the
 		 * tags because if another thread reads page->flags and builds a
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/extable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/extable.c
@@ -9,14 +9,19 @@
 int fixup_exception(struct pt_regs *regs)
 {
 	const struct exception_table_entry *fixup;
+	unsigned long addr;
 
-	fixup = search_exception_tables(instruction_pointer(regs));
-	if (!fixup)
-		return 0;
+	addr = instruction_pointer(regs);
 
-	if (in_bpf_jit(regs))
+	/* Search the BPF tables first, these are formatted differently */
+	fixup = search_bpf_extables(addr);
+	if (fixup)
 		return arm64_bpf_fixup_exception(fixup, regs);
 
+	fixup = search_exception_tables(addr);
+	if (!fixup)
+		return 0;
+
 	regs->pc = (unsigned long)&fixup->fixup + fixup->fixup;
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/fault.c
@@ -30,6 +30,7 @@
 #include <asm/bug.h>
 #include <asm/cmpxchg.h>
 #include <asm/cpufeature.h>
+#include <asm/efi.h>
 #include <asm/exception.h>
 #include <asm/daifflags.h>
 #include <asm/debug-monitors.h>
@@ -43,7 +44,7 @@
 #include <asm/traps.h>
 
 struct fault_info {
-	int	(*fn)(unsigned long far, unsigned int esr,
+	int	(*fn)(unsigned long far, unsigned long esr,
 		      struct pt_regs *regs);
 	int	sig;
 	int	code;
@@ -53,17 +54,17 @@
 static const struct fault_info fault_info[];
 static struct fault_info debug_fault_info[];
 
-static inline const struct fault_info *esr_to_fault_info(unsigned int esr)
+static inline const struct fault_info *esr_to_fault_info(unsigned long esr)
 {
 	return fault_info + (esr & ESR_ELx_FSC);
 }
 
-static inline const struct fault_info *esr_to_debug_fault_info(unsigned int esr)
+static inline const struct fault_info *esr_to_debug_fault_info(unsigned long esr)
 {
 	return debug_fault_info + DBG_ESR_EVT(esr);
 }
 
-static void data_abort_decode(unsigned int esr)
+static void data_abort_decode(unsigned long esr)
 {
 	pr_alert("Data abort info:\n");
 
@@ -85,11 +86,11 @@
 		 (esr & ESR_ELx_WNR) >> ESR_ELx_WNR_SHIFT);
 }
 
-static void mem_abort_decode(unsigned int esr)
+static void mem_abort_decode(unsigned long esr)
 {
 	pr_alert("Mem abort info:\n");
 
-	pr_alert("  ESR = 0x%08x\n", esr);
+	pr_alert("  ESR = 0x%016lx\n", esr);
 	pr_alert("  EC = 0x%02lx: %s, IL = %u bits\n",
 		 ESR_ELx_EC(esr), esr_get_class_string(esr),
 		 (esr & ESR_ELx_IL) ? 32 : 16);
@@ -99,7 +100,7 @@
 	pr_alert("  EA = %lu, S1PTW = %lu\n",
 		 (esr & ESR_ELx_EA) >> ESR_ELx_EA_SHIFT,
 		 (esr & ESR_ELx_S1PTW) >> ESR_ELx_S1PTW_SHIFT);
-	pr_alert("  FSC = 0x%02x: %s\n", (esr & ESR_ELx_FSC),
+	pr_alert("  FSC = 0x%02lx: %s\n", (esr & ESR_ELx_FSC),
 		 esr_to_fault_info(esr)->name);
 
 	if (esr_is_data_abort(esr))
@@ -229,20 +230,20 @@
 	return 1;
 }
 
-static bool is_el1_instruction_abort(unsigned int esr)
+static bool is_el1_instruction_abort(unsigned long esr)
 {
 	return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_CUR;
 }
 
-static bool is_el1_data_abort(unsigned int esr)
+static bool is_el1_data_abort(unsigned long esr)
 {
 	return ESR_ELx_EC(esr) == ESR_ELx_EC_DABT_CUR;
 }
 
-static inline bool is_el1_permission_fault(unsigned long addr, unsigned int esr,
+static inline bool is_el1_permission_fault(unsigned long addr, unsigned long esr,
 					   struct pt_regs *regs)
 {
-	unsigned int fsc_type = esr & ESR_ELx_FSC_TYPE;
+	unsigned long fsc_type = esr & ESR_ELx_FSC_TYPE;
 
 	if (!is_el1_data_abort(esr) && !is_el1_instruction_abort(esr))
 		return false;
@@ -258,7 +259,7 @@
 }
 
 static bool __kprobes is_spurious_el1_translation_fault(unsigned long addr,
-							unsigned int esr,
+							unsigned long esr,
 							struct pt_regs *regs)
 {
 	unsigned long flags;
@@ -290,7 +291,7 @@
 }
 
 static void die_kernel_fault(const char *msg, unsigned long addr,
-			     unsigned int esr, struct pt_regs *regs)
+			     unsigned long esr, struct pt_regs *regs)
 {
 	bust_spinlocks(1);
 
@@ -302,11 +303,11 @@
 	show_pte(addr);
 	die("Oops", regs, esr);
 	bust_spinlocks(0);
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 #ifdef CONFIG_KASAN_HW_TAGS
-static void report_tag_fault(unsigned long addr, unsigned int esr,
+static void report_tag_fault(unsigned long addr, unsigned long esr,
 			     struct pt_regs *regs)
 {
 	/*
@@ -318,11 +319,11 @@
 }
 #else
 /* Tag faults aren't enabled without CONFIG_KASAN_HW_TAGS. */
-static inline void report_tag_fault(unsigned long addr, unsigned int esr,
+static inline void report_tag_fault(unsigned long addr, unsigned long esr,
 				    struct pt_regs *regs) { }
 #endif
 
-static void do_tag_recovery(unsigned long addr, unsigned int esr,
+static void do_tag_recovery(unsigned long addr, unsigned long esr,
 			   struct pt_regs *regs)
 {
 
@@ -337,9 +338,9 @@
 	isb();
 }
 
-static bool is_el1_mte_sync_tag_check_fault(unsigned int esr)
+static bool is_el1_mte_sync_tag_check_fault(unsigned long esr)
 {
-	unsigned int fsc = esr & ESR_ELx_FSC;
+	unsigned long fsc = esr & ESR_ELx_FSC;
 
 	if (!is_el1_data_abort(esr))
 		return false;
@@ -350,7 +351,12 @@
 	return false;
 }
 
-static void __do_kernel_fault(unsigned long addr, unsigned int esr,
+static bool is_translation_fault(unsigned long esr)
+{
+	return (esr & ESR_ELx_FSC_TYPE) == ESR_ELx_FSC_FAULT;
+}
+
+static void __do_kernel_fault(unsigned long addr, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	const char *msg;
@@ -382,16 +388,20 @@
 	} else if (addr < PAGE_SIZE) {
 		msg = "NULL pointer dereference";
 	} else {
-		if (kfence_handle_page_fault(addr, esr & ESR_ELx_WNR, regs))
+		if (is_translation_fault(esr) &&
+		    kfence_handle_page_fault(addr, esr & ESR_ELx_WNR, regs))
 			return;
 
 		msg = "paging request";
 	}
 
+	if (efi_runtime_fixup_exception(regs, msg))
+		return;
+
 	die_kernel_fault(msg, addr, esr, regs);
 }
 
-static void set_thread_esr(unsigned long address, unsigned int esr)
+static void set_thread_esr(unsigned long address, unsigned long esr)
 {
 	current->thread.fault_address = address;
 
@@ -439,7 +449,7 @@
 			 * exception level). Fail safe by not providing an ESR
 			 * context record at all.
 			 */
-			WARN(1, "ESR 0x%x is not DABT or IABT from EL0\n", esr);
+			WARN(1, "ESR 0x%lx is not DABT or IABT from EL0\n", esr);
 			esr = 0;
 			break;
 		}
@@ -448,7 +458,7 @@
 	current->thread.fault_code = esr;
 }
 
-static void do_bad_area(unsigned long far, unsigned int esr,
+static void do_bad_area(unsigned long far, unsigned long esr,
 			struct pt_regs *regs)
 {
 	unsigned long addr = untagged_addr(far);
@@ -467,8 +477,8 @@
 	}
 }
 
-#define VM_FAULT_BADMAP		0x010000
-#define VM_FAULT_BADACCESS	0x020000
+#define VM_FAULT_BADMAP		((__force vm_fault_t)0x010000)
+#define VM_FAULT_BADACCESS	((__force vm_fault_t)0x020000)
 
 static vm_fault_t __do_page_fault(struct mm_struct *mm, unsigned long addr,
 				  unsigned int mm_flags, unsigned long vm_flags,
@@ -499,7 +509,7 @@
 	return handle_mm_fault(vma, addr, mm_flags, regs);
 }
 
-static bool is_el0_instruction_abort(unsigned int esr)
+static bool is_el0_instruction_abort(unsigned long esr)
 {
 	return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_LOW;
 }
@@ -508,12 +518,12 @@
  * Note: not valid for EL1 DC IVAC, but we never use that such that it
  * should fault. EL0 cannot issue DC IVAC (undef).
  */
-static bool is_write_abort(unsigned int esr)
+static bool is_write_abort(unsigned long esr)
 {
 	return (esr & ESR_ELx_WNR) && !(esr & ESR_ELx_CM);
 }
 
-static int __kprobes do_page_fault(unsigned long far, unsigned int esr,
+static int __kprobes do_page_fault(unsigned long far, unsigned long esr,
 				   struct pt_regs *regs)
 {
 	const struct fault_info *inf;
@@ -671,7 +681,7 @@
 }
 
 static int __kprobes do_translation_fault(unsigned long far,
-					  unsigned int esr,
+					  unsigned long esr,
 					  struct pt_regs *regs)
 {
 	unsigned long addr = untagged_addr(far);
@@ -683,19 +693,19 @@
 	return 0;
 }
 
-static int do_alignment_fault(unsigned long far, unsigned int esr,
+static int do_alignment_fault(unsigned long far, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	do_bad_area(far, esr, regs);
 	return 0;
 }
 
-static int do_bad(unsigned long far, unsigned int esr, struct pt_regs *regs)
+static int do_bad(unsigned long far, unsigned long esr, struct pt_regs *regs)
 {
 	return 1; /* "fault" */
 }
 
-static int do_sea(unsigned long far, unsigned int esr, struct pt_regs *regs)
+static int do_sea(unsigned long far, unsigned long esr, struct pt_regs *regs)
 {
 	const struct fault_info *inf;
 	unsigned long siaddr;
@@ -725,7 +735,7 @@
 	return 0;
 }
 
-static int do_tag_check_fault(unsigned long far, unsigned int esr,
+static int do_tag_check_fault(unsigned long far, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	/*
@@ -805,7 +815,7 @@
 	{ do_bad,		SIGKILL, SI_KERNEL,	"unknown 63"			},
 };
 
-void do_mem_abort(unsigned long far, unsigned int esr, struct pt_regs *regs)
+void do_mem_abort(unsigned long far, unsigned long esr, struct pt_regs *regs)
 {
 	const struct fault_info *inf = esr_to_fault_info(esr);
 	unsigned long addr = untagged_addr(far);
@@ -828,14 +838,14 @@
 }
 NOKPROBE_SYMBOL(do_mem_abort);
 
-void do_sp_pc_abort(unsigned long addr, unsigned int esr, struct pt_regs *regs)
+void do_sp_pc_abort(unsigned long addr, unsigned long esr, struct pt_regs *regs)
 {
 	arm64_notify_die("SP/PC alignment exception", regs, SIGBUS, BUS_ADRALN,
 			 addr, esr);
 }
 NOKPROBE_SYMBOL(do_sp_pc_abort);
 
-int __init early_brk64(unsigned long addr, unsigned int esr,
+int __init early_brk64(unsigned long addr, unsigned long esr,
 		       struct pt_regs *regs);
 
 /*
@@ -855,7 +865,7 @@
 };
 
 void __init hook_debug_fault_code(int nr,
-				  int (*fn)(unsigned long, unsigned int, struct pt_regs *),
+				  int (*fn)(unsigned long, unsigned long, struct pt_regs *),
 				  int sig, int code, const char *name)
 {
 	BUG_ON(nr < 0 || nr >= ARRAY_SIZE(debug_fault_info));
@@ -888,7 +898,7 @@
 }
 NOKPROBE_SYMBOL(debug_exception_exit);
 
-void do_debug_exception(unsigned long addr_if_watchpoint, unsigned int esr,
+void do_debug_exception(unsigned long addr_if_watchpoint, unsigned long esr,
 			struct pt_regs *regs)
 {
 	const struct fault_info *inf = esr_to_debug_fault_info(esr);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/init.c
@@ -61,10 +61,63 @@
  * unless restricted on specific platforms (e.g. 30-bit on Raspberry Pi 4).
  * In such case, ZONE_DMA32 covers the rest of the 32-bit addressable memory,
  * otherwise it is empty.
+ *
+ * Memory reservation for crash kernel either done early or deferred
+ * depending on DMA memory zones configs (ZONE_DMA) --
+ *
+ * In absence of ZONE_DMA configs arm64_dma_phys_limit initialized
+ * here instead of max_zone_phys().  This lets early reservation of
+ * crash kernel memory which has a dependency on arm64_dma_phys_limit.
+ * Reserving memory early for crash kernel allows linear creation of block
+ * mappings (greater than page-granularity) for all the memory bank rangs.
+ * In this scheme a comparatively quicker boot is observed.
+ *
+ * If ZONE_DMA configs are defined, crash kernel memory reservation
+ * is delayed until DMA zone memory range size initilazation performed in
+ * zone_sizes_init().  The defer is necessary to steer clear of DMA zone
+ * memory range to avoid overlap allocation.  So crash kernel memory boundaries
+ * are not known when mapping all bank memory ranges, which otherwise means
+ * not possible to exclude crash kernel range from creating block mappings
+ * so page-granularity mappings are created for the entire memory range.
+ * Hence a slightly slower boot is observed.
+ *
+ * Note: Page-granularity mapppings are necessary for crash kernel memory
+ * range for shrinking its size via /sys/kernel/kexec_crash_size interface.
  */
-phys_addr_t arm64_dma_phys_limit __ro_after_init;
+#if IS_ENABLED(CONFIG_ZONE_DMA) || IS_ENABLED(CONFIG_ZONE_DMA32)
+phys_addr_t __ro_after_init arm64_dma_phys_limit;
+#else
+phys_addr_t __ro_after_init arm64_dma_phys_limit = PHYS_MASK + 1;
+#endif
+
+/* Current arm64 boot protocol requires 2MB alignment */
+#define CRASH_ALIGN			SZ_2M
+
+#define CRASH_ADDR_LOW_MAX		arm64_dma_phys_limit
+#define CRASH_ADDR_HIGH_MAX		(PHYS_MASK + 1)
+
+#define DEFAULT_CRASH_KERNEL_LOW_SIZE	(128UL << 20)
+
+static int __init reserve_crashkernel_low(unsigned long long low_size)
+{
+	unsigned long long low_base;
+
+	low_base = memblock_phys_alloc_range(low_size, CRASH_ALIGN, 0, CRASH_ADDR_LOW_MAX);
+	if (!low_base) {
+		pr_err("cannot allocate crashkernel low memory (size:0x%llx).\n", low_size);
+		return -ENOMEM;
+	}
+
+	pr_info("crashkernel low memory reserved: 0x%08llx - 0x%08llx (%lld MB)\n",
+		low_base, low_base + low_size, low_size >> 20);
+
+	crashk_low_res.start = low_base;
+	crashk_low_res.end   = low_base + low_size - 1;
+	insert_resource(&iomem_resource, &crashk_low_res);
+
+	return 0;
+}
 
-#ifdef CONFIG_KEXEC_CORE
 /*
  * reserve_crashkernel() - reserves memory for crash kernel
  *
@@ -75,30 +128,73 @@
 static void __init reserve_crashkernel(void)
 {
 	unsigned long long crash_base, crash_size;
-	unsigned long long crash_max = arm64_dma_phys_limit;
+	unsigned long long crash_low_size = 0;
+	unsigned long long crash_max = CRASH_ADDR_LOW_MAX;
+	char *cmdline = boot_command_line;
 	int ret;
+	bool fixed_base = false;
 
-	ret = parse_crashkernel(boot_command_line, memblock_phys_mem_size(),
+	if (!IS_ENABLED(CONFIG_KEXEC_CORE))
+		return;
+
+	/* crashkernel=X[@offset] */
+	ret = parse_crashkernel(cmdline, memblock_phys_mem_size(),
 				&crash_size, &crash_base);
-	/* no crashkernel= or invalid value specified */
-	if (ret || !crash_size)
+	if (ret == -ENOENT) {
+		ret = parse_crashkernel_high(cmdline, 0, &crash_size, &crash_base);
+		if (ret || !crash_size)
+			return;
+
+		/*
+		 * crashkernel=Y,low can be specified or not, but invalid value
+		 * is not allowed.
+		 */
+		ret = parse_crashkernel_low(cmdline, 0, &crash_low_size, &crash_base);
+		if (ret == -ENOENT)
+			crash_low_size = DEFAULT_CRASH_KERNEL_LOW_SIZE;
+		else if (ret)
+			return;
+
+		crash_max = CRASH_ADDR_HIGH_MAX;
+	} else if (ret || !crash_size) {
+		/* The specified value is invalid */
 		return;
+	}
 
 	crash_size = PAGE_ALIGN(crash_size);
 
 	/* User specifies base address explicitly. */
-	if (crash_base)
+	if (crash_base) {
+		fixed_base = true;
 		crash_max = crash_base + crash_size;
+	}
 
-	/* Current arm64 boot protocol requires 2MB alignment */
-	crash_base = memblock_phys_alloc_range(crash_size, SZ_2M,
+retry:
+	crash_base = memblock_phys_alloc_range(crash_size, CRASH_ALIGN,
 					       crash_base, crash_max);
 	if (!crash_base) {
+		/*
+		 * If the first attempt was for low memory, fall back to
+		 * high memory, the minimum required low memory will be
+		 * reserved later.
+		 */
+		if (!fixed_base && (crash_max == CRASH_ADDR_LOW_MAX)) {
+			crash_max = CRASH_ADDR_HIGH_MAX;
+			crash_low_size = DEFAULT_CRASH_KERNEL_LOW_SIZE;
+			goto retry;
+		}
+
 		pr_warn("cannot allocate crashkernel (size:0x%llx)\n",
 			crash_size);
 		return;
 	}
 
+	if ((crash_base > CRASH_ADDR_LOW_MAX - crash_low_size) &&
+	     crash_low_size && reserve_crashkernel_low(crash_low_size)) {
+		memblock_free(crash_base, crash_size);
+		return;
+	}
+
 	pr_info("crashkernel reserved: 0x%016llx - 0x%016llx (%lld MB)\n",
 		crash_base, crash_base + crash_size, crash_size >> 20);
 
@@ -107,14 +203,12 @@
 	 * map. Inform kmemleak so that it won't try to access it.
 	 */
 	kmemleak_ignore_phys(crash_base);
+	if (crashk_low_res.end)
+		kmemleak_ignore_phys(crashk_low_res.start);
+
 	crashk_res.start = crash_base;
 	crashk_res.end = crash_base + crash_size - 1;
 }
-#else
-static void __init reserve_crashkernel(void)
-{
-}
-#endif /* CONFIG_KEXEC_CORE */
 
 /*
  * Return the maximum physical address for a zone accessible by the given bits
@@ -153,50 +247,11 @@
 	if (!arm64_dma_phys_limit)
 		arm64_dma_phys_limit = dma32_phys_limit;
 #endif
-	if (!arm64_dma_phys_limit)
-		arm64_dma_phys_limit = PHYS_MASK + 1;
 	max_zone_pfns[ZONE_NORMAL] = max;
 
 	free_area_init(max_zone_pfns);
 }
 
-int pfn_valid(unsigned long pfn)
-{
-	phys_addr_t addr = PFN_PHYS(pfn);
-	struct mem_section *ms;
-
-	/*
-	 * Ensure the upper PAGE_SHIFT bits are clear in the
-	 * pfn. Else it might lead to false positives when
-	 * some of the upper bits are set, but the lower bits
-	 * match a valid pfn.
-	 */
-	if (PHYS_PFN(addr) != pfn)
-		return 0;
-
-	if (pfn_to_section_nr(pfn) >= NR_MEM_SECTIONS)
-		return 0;
-
-	ms = __pfn_to_section(pfn);
-	if (!valid_section(ms))
-		return 0;
-
-	/*
-	 * ZONE_DEVICE memory does not have the memblock entries.
-	 * memblock_is_map_memory() check for ZONE_DEVICE based
-	 * addresses will always fail. Even the normal hotplugged
-	 * memory will never have MEMBLOCK_NOMAP flag set in their
-	 * memblock entries. Skip memblock search for all non early
-	 * memory sections covering all of hotplug memory including
-	 * both normal and ZONE_DEVICE based.
-	 */
-	if (!early_section(ms))
-		return pfn_section_valid(ms, pfn);
-
-	return memblock_is_memory(addr);
-}
-EXPORT_SYMBOL(pfn_valid);
-
 int pfn_is_map_memory(unsigned long pfn)
 {
 	phys_addr_t addr = PFN_PHYS(pfn);
@@ -352,6 +407,9 @@
 
 	early_init_fdt_scan_reserved_mem();
 
+	if (!defer_reserve_crashkernel())
+		reserve_crashkernel();
+
 	high_memory = __va(memblock_end_of_DRAM() - 1) + 1;
 }
 
@@ -398,7 +456,8 @@
 	 * request_standard_resources() depends on crashkernel's memory being
 	 * reserved, so do it here.
 	 */
-	reserve_crashkernel();
+	if (defer_reserve_crashkernel())
+		reserve_crashkernel();
 
 	memblock_dump_all();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/ioremap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/ioremap.c
@@ -99,3 +99,11 @@
 {
 	early_ioremap_setup();
 }
+
+bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+				 unsigned long flags)
+{
+	unsigned long pfn = PHYS_PFN(offset);
+
+	return pfn_is_map_memory(pfn);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/mmap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/mmap.c
@@ -7,8 +7,10 @@
 
 #include <linux/io.h>
 #include <linux/memblock.h>
+#include <linux/mm.h>
 #include <linux/types.h>
 
+#include <asm/cpufeature.h>
 #include <asm/page.h>
 
 /*
@@ -38,3 +40,18 @@
 {
 	return !(((pfn << PAGE_SHIFT) + size) & ~PHYS_MASK);
 }
+
+static int __init adjust_protection_map(void)
+{
+	/*
+	 * With Enhanced PAN we can honour the execute-only permissions as
+	 * there is no PAN override with such mappings.
+	 */
+	if (cpus_have_const_cap(ARM64_HAS_EPAN)) {
+		protection_map[VM_EXEC] = PAGE_EXECONLY;
+		protection_map[VM_EXEC | VM_SHARED] = PAGE_EXECONLY;
+	}
+
+	return 0;
+}
+arch_initcall(adjust_protection_map);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/mmu.c
@@ -63,6 +63,7 @@
 static pud_t bm_pud[PTRS_PER_PUD] __page_aligned_bss __maybe_unused;
 
 static DEFINE_SPINLOCK(swapper_pgdir_lock);
+static DEFINE_MUTEX(fixmap_lock);
 
 void set_swapper_pgd(pgd_t *pgdp, pgd_t pgd)
 {
@@ -328,6 +329,12 @@
 	}
 	BUG_ON(p4d_bad(p4d));
 
+	/*
+	 * No need for locking during early boot. And it doesn't work as
+	 * expected with KASLR enabled.
+	 */
+	if (system_state != SYSTEM_BOOTING)
+		mutex_lock(&fixmap_lock);
 	pudp = pud_set_fixmap_offset(p4dp, addr);
 	do {
 		pud_t old_pud = READ_ONCE(*pudp);
@@ -358,6 +365,8 @@
 	} while (pudp++, addr = next, addr != end);
 
 	pud_clear_fixmap();
+	if (system_state != SYSTEM_BOOTING)
+		mutex_unlock(&fixmap_lock);
 }
 
 static void __create_pgd_mapping(pgd_t *pgdir, phys_addr_t phys,
@@ -426,7 +435,7 @@
 static void __init create_mapping_noalloc(phys_addr_t phys, unsigned long virt,
 				  phys_addr_t size, pgprot_t prot)
 {
-	if ((virt >= PAGE_END) && (virt < VMALLOC_START)) {
+	if (virt < PAGE_OFFSET) {
 		pr_warn("BUG: not creating mapping for %pa at 0x%016lx - outside kernel range\n",
 			&phys, virt);
 		return;
@@ -453,7 +462,7 @@
 static void update_mapping_prot(phys_addr_t phys, unsigned long virt,
 				phys_addr_t size, pgprot_t prot)
 {
-	if ((virt >= PAGE_END) && (virt < VMALLOC_START)) {
+	if (virt < PAGE_OFFSET) {
 		pr_warn("BUG: not updating mapping for %pa at 0x%016lx - outside kernel range\n",
 			&phys, virt);
 		return;
@@ -516,7 +525,7 @@
 	 */
 	BUILD_BUG_ON(pgd_index(direct_map_end - 1) == pgd_index(direct_map_end));
 
-	if (can_set_direct_map() || crash_mem_map || IS_ENABLED(CONFIG_KFENCE))
+	if (can_set_direct_map() || IS_ENABLED(CONFIG_KFENCE))
 		flags |= NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS;
 
 	/*
@@ -527,6 +536,16 @@
 	 */
 	memblock_mark_nomap(kernel_start, kernel_end - kernel_start);
 
+#ifdef CONFIG_KEXEC_CORE
+	if (crash_mem_map) {
+		if (defer_reserve_crashkernel())
+			flags |= NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS;
+		else if (crashk_res.end)
+			memblock_mark_nomap(crashk_res.start,
+			    resource_size(&crashk_res));
+	}
+#endif
+
 	/* map all the memory banks */
 	for_each_mem_range(i, &start, &end) {
 		if (start >= end)
@@ -553,6 +572,24 @@
 	__map_memblock(pgdp, kernel_start, kernel_end,
 		       PAGE_KERNEL, NO_CONT_MAPPINGS);
 	memblock_clear_nomap(kernel_start, kernel_end - kernel_start);
+
+	/*
+	 * Use page-level mappings here so that we can shrink the region
+	 * in page granularity and put back unused memory to buddy system
+	 * through /sys/kernel/kexec_crash_size interface.
+	 */
+#ifdef CONFIG_KEXEC_CORE
+	if (crash_mem_map && !defer_reserve_crashkernel()) {
+		if (crashk_res.end) {
+			__map_memblock(pgdp, crashk_res.start,
+				       crashk_res.end + 1,
+				       PAGE_KERNEL,
+				       NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS);
+			memblock_clear_nomap(crashk_res.start,
+					     resource_size(&crashk_res));
+		}
+	}
+#endif
 }
 
 void mark_rodata_ro(void)
@@ -616,6 +653,8 @@
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 static int __init map_entry_trampoline(void)
 {
+	int i;
+
 	pgprot_t prot = rodata_enabled ? PAGE_KERNEL_ROX : PAGE_KERNEL_EXEC;
 	phys_addr_t pa_start = __pa_symbol(__entry_tramp_text_start);
 
@@ -624,11 +663,15 @@
 
 	/* Map only the text into the trampoline page table */
 	memset(tramp_pg_dir, 0, PGD_SIZE);
-	__create_pgd_mapping(tramp_pg_dir, pa_start, TRAMP_VALIAS, PAGE_SIZE,
-			     prot, __pgd_pgtable_alloc, 0);
+	__create_pgd_mapping(tramp_pg_dir, pa_start, TRAMP_VALIAS,
+			     entry_tramp_text_size(), prot,
+			     __pgd_pgtable_alloc, NO_BLOCK_MAPPINGS);
 
 	/* Map both the text and data into the kernel page table */
-	__set_fixmap(FIX_ENTRY_TRAMP_TEXT, pa_start, prot);
+	for (i = 0; i < DIV_ROUND_UP(entry_tramp_text_size(), PAGE_SIZE); i++)
+		__set_fixmap(FIX_ENTRY_TRAMP_TEXT1 - i,
+			     pa_start + i * PAGE_SIZE, prot);
+
 	if (IS_ENABLED(CONFIG_RANDOMIZE_BASE)) {
 		extern char __entry_tramp_data_start[];
 
@@ -1499,6 +1542,11 @@
 	if (ret)
 		__remove_pgd_mapping(swapper_pg_dir,
 				     __phys_to_virt(start), size);
+	else {
+		max_pfn = PFN_UP(start + size);
+		max_low_pfn = max_pfn;
+	}
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/mteswap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/mteswap.c
@@ -62,7 +62,12 @@
 	 * the new page->flags are visible before the tags were updated.
 	 */
 	smp_wmb();
-	mte_restore_page_tags(page_address(page), tags);
+	/*
+	 * Test PG_mte_tagged again in case it was racing with another
+	 * set_pte_at().
+	 */
+	if (!test_and_set_bit(PG_mte_tagged, &page->flags))
+		mte_restore_page_tags(page_address(page), tags);
 
 	return true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/pageattr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/pageattr.c
@@ -211,9 +211,6 @@
 	pte_t *ptep;
 	unsigned long addr = (unsigned long)page_address(page);
 
-	if (!can_set_direct_map())
-		return true;
-
 	pgdp = pgd_offset_k(addr);
 	if (pgd_none(READ_ONCE(*pgdp)))
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/proc.S
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/proc.S
@@ -46,18 +46,20 @@
 #endif
 
 #ifdef CONFIG_KASAN_HW_TAGS
-#define TCR_MTE_FLAGS SYS_TCR_EL1_TCMA1 | TCR_TBI1 | TCR_TBID1
-#else
+#define TCR_MTE_FLAGS TCR_TCMA1 | TCR_TBI1 | TCR_TBID1
+#elif defined(CONFIG_ARM64_MTE)
 /*
  * The mte_zero_clear_page_tags() implementation uses DC GZVA, which relies on
  * TBI being enabled at EL1.
  */
 #define TCR_MTE_FLAGS TCR_TBI1 | TCR_TBID1
+#else
+#define TCR_MTE_FLAGS 0
 #endif
 
 /*
  * Default MAIR_EL1. MT_NORMAL_TAGGED is initially mapped as Normal memory and
- * changed during __cpu_setup to Normal Tagged if the system supports MTE.
+ * changed during mte_cpu_setup to Normal Tagged if the system supports MTE.
  */
 #define MAIR_EL1_SET							\
 	(MAIR_ATTRIDX(MAIR_ATTR_DEVICE_nGnRnE, MT_DEVICE_nGnRnE) |	\
@@ -421,46 +423,8 @@
 	mov_q	mair, MAIR_EL1_SET
 	mov_q	tcr, TCR_TxSZ(VA_BITS) | TCR_CACHE_FLAGS | TCR_SMP_FLAGS | \
 			TCR_TG_FLAGS | TCR_KASLR_FLAGS | TCR_ASID16 | \
-			TCR_TBI0 | TCR_A1 | TCR_KASAN_SW_FLAGS
-
-#ifdef CONFIG_ARM64_MTE
-	/*
-	 * Update MAIR_EL1, GCR_EL1 and TFSR*_EL1 if MTE is supported
-	 * (ID_AA64PFR1_EL1[11:8] > 1).
-	 */
-	mrs	x10, ID_AA64PFR1_EL1
-	ubfx	x10, x10, #ID_AA64PFR1_MTE_SHIFT, #4
-	cmp	x10, #ID_AA64PFR1_MTE
-	b.lt	1f
-
-	/* Normal Tagged memory type at the corresponding MAIR index */
-	mov	x10, #MAIR_ATTR_NORMAL_TAGGED
-	bfi	mair, x10, #(8 *  MT_NORMAL_TAGGED), #8
+			TCR_TBI0 | TCR_A1 | TCR_KASAN_SW_FLAGS | TCR_MTE_FLAGS
 
-	mov	x10, #KERNEL_GCR_EL1
-	msr_s	SYS_GCR_EL1, x10
-
-	/*
-	 * If GCR_EL1.RRND=1 is implemented the same way as RRND=0, then
-	 * RGSR_EL1.SEED must be non-zero for IRG to produce
-	 * pseudorandom numbers. As RGSR_EL1 is UNKNOWN out of reset, we
-	 * must initialize it.
-	 */
-	mrs	x10, CNTVCT_EL0
-	ands	x10, x10, #SYS_RGSR_EL1_SEED_MASK
-	csinc	x10, x10, xzr, ne
-	lsl	x10, x10, #SYS_RGSR_EL1_SEED_SHIFT
-	msr_s	SYS_RGSR_EL1, x10
-
-	/* clear any pending tag check faults in TFSR*_EL1 */
-	msr_s	SYS_TFSR_EL1, xzr
-	msr_s	SYS_TFSRE0_EL1, xzr
-
-	/* set the TCR_EL1 bits */
-	mov_q	x10, TCR_MTE_FLAGS
-	orr	tcr, tcr, x10
-1:
-#endif
 	tcr_clear_errata_bits tcr, x9, x5
 
 #ifdef CONFIG_ARM64_VA_BITS_52
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/mm/ptdump.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/mm/ptdump.c
@@ -41,8 +41,6 @@
 	{ 0 /* KASAN_SHADOW_START */,	"Kasan shadow start" },
 	{ KASAN_SHADOW_END,		"Kasan shadow end" },
 #endif
-	{ BPF_JIT_REGION_START,		"BPF start" },
-	{ BPF_JIT_REGION_END,		"BPF end" },
 	{ MODULES_VADDR,		"Modules start" },
 	{ MODULES_END,			"Modules end" },
 	{ VMALLOC_START,		"vmalloc() area" },
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/net/bpf_jit_comp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/net/bpf_jit_comp.c
@@ -788,7 +788,10 @@
 		u64 imm64;
 
 		imm64 = (u64)insn1.imm << 32 | (u32)imm;
-		emit_a64_mov_i64(dst, imm64, ctx);
+		if (bpf_pseudo_func(insn))
+			emit_addr_mov_i64(dst, imm64, ctx);
+		else
+			emit_a64_mov_i64(dst, imm64, ctx);
 
 		return 1;
 	}
@@ -1042,15 +1045,18 @@
 		goto out_off;
 	}
 
-	/* 1. Initial fake pass to compute ctx->idx. */
-
-	/* Fake pass to fill in ctx->offset. */
-	if (build_body(&ctx, extra_pass)) {
+	/*
+	 * 1. Initial fake pass to compute ctx->idx and ctx->offset.
+	 *
+	 * BPF line info needs ctx->offset[i] to be the offset of
+	 * instruction[i] in jited image, so build prologue first.
+	 */
+	if (build_prologue(&ctx, was_classic)) {
 		prog = orig_prog;
 		goto out_off;
 	}
 
-	if (build_prologue(&ctx, was_classic)) {
+	if (build_body(&ctx, extra_pass)) {
 		prog = orig_prog;
 		goto out_off;
 	}
@@ -1110,6 +1116,7 @@
 			bpf_jit_binary_free(header);
 			prog->bpf_func = NULL;
 			prog->jited = 0;
+			prog->jited_len = 0;
 			goto out_off;
 		}
 		bpf_jit_binary_lock_ro(header);
@@ -1123,6 +1130,11 @@
 	prog->jited_len = prog_size;
 
 	if (!prog->is_func || extra_pass) {
+		int i;
+
+		/* offset[prog->len] is the size of program */
+		for (i = 0; i <= prog->len; i++)
+			ctx.offset[i] *= AARCH64_INSN_SIZE;
 		bpf_prog_fill_jited_linfo(prog, ctx.offset + 1);
 out_off:
 		kfree(ctx.offset);
@@ -1138,15 +1150,12 @@
 
 u64 bpf_jit_alloc_exec_limit(void)
 {
-	return BPF_JIT_REGION_SIZE;
+	return VMALLOC_END - VMALLOC_START;
 }
 
 void *bpf_jit_alloc_exec(unsigned long size)
 {
-	return __vmalloc_node_range(size, PAGE_SIZE, BPF_JIT_REGION_START,
-				    BPF_JIT_REGION_END, GFP_KERNEL,
-				    PAGE_KERNEL, 0, NUMA_NO_NODE,
-				    __builtin_return_address(0));
+	return vmalloc(size);
 }
 
 void bpf_jit_free_exec(void *addr)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/arm64/tools/cpucaps
+++ linux-xilinx-zynqmp-5.15.0/arch/arm64/tools/cpucaps
@@ -42,6 +42,7 @@
 SPECTRE_V2
 SPECTRE_V3A
 SPECTRE_V4
+SPECTRE_BHB
 SSBS
 SVE
 UNMAP_KERNEL_AT_EL0
@@ -53,6 +54,11 @@
 WORKAROUND_1463225
 WORKAROUND_1508412
 WORKAROUND_1542419
+WORKAROUND_1742098
+WORKAROUND_2457168
+WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+WORKAROUND_TSB_FLUSH_FAILURE
+WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
 WORKAROUND_CAVIUM_23154
 WORKAROUND_CAVIUM_27456
 WORKAROUND_CAVIUM_30115
@@ -64,3 +70,4 @@
 WORKAROUND_QCOM_FALKOR_E1003
 WORKAROUND_REPEAT_TLBI
 WORKAROUND_SPECULATIVE_AT
+WORKAROUND_SPECULATIVE_SSBS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/abiv1/alignment.c
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/abiv1/alignment.c
@@ -294,7 +294,7 @@
 				__func__, opcode, rz, rx, imm, addr);
 		show_regs(regs);
 		bust_spinlocks(0);
-		do_exit(SIGKILL);
+		make_task_dead(SIGKILL);
 	}
 
 	force_sig_fault(SIGBUS, BUS_ADRALN, (void __user *)addr);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/include/asm/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/include/asm/irq_work.h
@@ -7,5 +7,5 @@
 {
 	return true;
 }
-extern void arch_irq_work_raise(void);
+
 #endif /* __ASM_CSKY_IRQ_WORK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/include/asm/kprobes.h
@@ -41,7 +41,7 @@
 int kprobe_fault_handler(struct pt_regs *regs, unsigned int trapnr);
 int kprobe_breakpoint_handler(struct pt_regs *regs);
 int kprobe_single_step_handler(struct pt_regs *regs);
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 void __kprobes *trampoline_probe_handler(struct pt_regs *regs);
 
 #endif /* CONFIG_KPROBES */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/include/asm/uaccess.h
@@ -3,14 +3,13 @@
 #ifndef __ASM_CSKY_UACCESS_H
 #define __ASM_CSKY_UACCESS_H
 
-#define user_addr_max() \
-	(uaccess_kernel() ? KERNEL_DS.seg : get_fs().seg)
+#define user_addr_max() (current_thread_info()->addr_limit.seg)
 
 static inline int __access_ok(unsigned long addr, unsigned long size)
 {
-	unsigned long limit = current_thread_info()->addr_limit.seg;
+	unsigned long limit = user_addr_max();
 
-	return ((addr < limit) && ((addr + size) < limit));
+	return (size <= limit) && (addr <= (limit - size));
 }
 #define __access_ok __access_ok
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/include/uapi/asm/unistd.h
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/include/uapi/asm/unistd.h
@@ -6,6 +6,7 @@
 #define __ARCH_WANT_SYS_CLONE3
 #define __ARCH_WANT_SET_GET_RLIMIT
 #define __ARCH_WANT_TIME32_SYSCALLS
+#define __ARCH_WANT_SYNC_FILE_RANGE2
 #include <asm-generic/unistd.h>
 
 #define __NR_set_thread_area	(__NR_arch_specific_syscall + 0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/kernel/perf_callchain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/kernel/perf_callchain.c
@@ -49,7 +49,7 @@
 {
 	struct stackframe buftail;
 	unsigned long lr = 0;
-	unsigned long *user_frame_tail = (unsigned long *)fp;
+	unsigned long __user *user_frame_tail = (unsigned long __user *)fp;
 
 	/* Check accessibility of one struct frame_tail beyond */
 	if (!access_ok(user_frame_tail, sizeof(buftail)))
@@ -86,10 +86,11 @@
 void perf_callchain_user(struct perf_callchain_entry_ctx *entry,
 			 struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	unsigned long fp = 0;
 
 	/* C-SKY does not support virtualization. */
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
+	if (guest_cbs && guest_cbs->is_in_guest())
 		return;
 
 	fp = regs->regs[4];
@@ -110,10 +111,11 @@
 void perf_callchain_kernel(struct perf_callchain_entry_ctx *entry,
 			   struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct stackframe fr;
 
 	/* C-SKY does not support virtualization. */
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		pr_warn("C-SKY does not support perf in guest mode!");
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/kernel/probes/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/kernel/probes/kprobes.c
@@ -1,5 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/kprobes.h>
 #include <linux/extable.h>
 #include <linux/slab.h>
@@ -28,7 +30,7 @@
 	struct csky_insn_patch *param = priv;
 	unsigned int addr = (unsigned int)param->addr;
 
-	if (atomic_inc_return(&param->cpu_count) == 1) {
+	if (atomic_inc_return(&param->cpu_count) == num_online_cpus()) {
 		*(u16 *) addr = cpu_to_le16(param->opcode);
 		dcache_wb_range(addr, addr + 2);
 		atomic_inc(&param->cpu_count);
@@ -77,10 +79,8 @@
 {
 	unsigned long probe_addr = (unsigned long)p->addr;
 
-	if (probe_addr & 0x1) {
-		pr_warn("Address not aligned.\n");
-		return -EINVAL;
-	}
+	if (probe_addr & 0x1)
+		return -EILSEQ;
 
 	/* copy instruction */
 	p->opcode = le32_to_cpu(*p->addr);
@@ -124,6 +124,10 @@
 
 void __kprobes arch_remove_kprobe(struct kprobe *p)
 {
+	if (p->ainsn.api.insn) {
+		free_insn_slot(p->ainsn.api.insn, 0);
+		p->ainsn.api.insn = NULL;
+	}
 }
 
 static void __kprobes save_previous_kprobe(struct kprobe_ctlblk *kcb)
@@ -225,7 +229,7 @@
 		break;
 	case KPROBE_HIT_SS:
 	case KPROBE_REENTER:
-		pr_warn("Unrecoverable kprobe detected.\n");
+		pr_warn("Failed to recover from reentered kprobes.\n");
 		dump_kprobe(p);
 		BUG();
 		break;
@@ -386,7 +390,7 @@
 
 void __kprobes __used *trampoline_probe_handler(struct pt_regs *regs)
 {
-	return (void *)kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	return (void *)kretprobe_trampoline_handler(regs, NULL);
 }
 
 void __kprobes arch_prepare_kretprobe(struct kretprobe_instance *ri,
@@ -394,7 +398,7 @@
 {
 	ri->ret_addr = (kprobe_opcode_t *)regs->lr;
 	ri->fp = NULL;
-	regs->lr = (unsigned long) &kretprobe_trampoline;
+	regs->lr = (unsigned long) &__kretprobe_trampoline;
 }
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/kernel/probes/kprobes_trampoline.S
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/kernel/probes/kprobes_trampoline.S
@@ -4,7 +4,7 @@
 
 #include <abi/entry.h>
 
-ENTRY(kretprobe_trampoline)
+ENTRY(__kretprobe_trampoline)
 	SAVE_REGS_FTRACE
 
 	mov	a0, sp /* pt_regs */
@@ -16,4 +16,4 @@
 
 	RESTORE_REGS_FTRACE
 	rts
-ENDPROC(kretprobe_trampoline)
+ENDPROC(__kretprobe_trampoline)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/kernel/signal.c
@@ -136,7 +136,7 @@
 static int
 setup_rt_frame(struct ksignal *ksig, sigset_t *set, struct pt_regs *regs)
 {
-	struct rt_sigframe *frame;
+	struct rt_sigframe __user *frame;
 	int err = 0;
 
 	frame = get_sigframe(ksig, regs, sizeof(*frame));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/kernel/traps.c
@@ -109,7 +109,7 @@
 	if (panic_on_oops)
 		panic("Fatal exception");
 	if (ret != NOTIFY_STOP)
-		do_exit(SIGSEGV);
+		make_task_dead(SIGSEGV);
 }
 
 void do_trap(struct pt_regs *regs, int signo, int code, unsigned long addr)
@@ -209,7 +209,7 @@
 
 asmlinkage void do_trap_fpe(struct pt_regs *regs)
 {
-#ifdef CONFIG_CPU_HAS_FP
+#ifdef CONFIG_CPU_HAS_FPU
 	return fpu_fpe(regs);
 #else
 	do_trap_error(regs, SIGILL, ILL_ILLOPC, regs->pc,
@@ -219,7 +219,7 @@
 
 asmlinkage void do_trap_priv(struct pt_regs *regs)
 {
-#ifdef CONFIG_CPU_HAS_FP
+#ifdef CONFIG_CPU_HAS_FPU
 	if (user_mode(regs) && fpu_libc_helper(regs))
 		return;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/csky/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/csky/mm/fault.c
@@ -67,7 +67,7 @@
 	pr_alert("Unable to handle kernel paging request at virtual "
 		 "addr 0x%08lx, pc: 0x%08lx\n", addr, regs->pc);
 	die(regs, "Oops");
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 static inline void mm_fault_error(struct pt_regs *regs, unsigned long addr, vm_fault_t fault)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/h8300/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/h8300/kernel/traps.c
@@ -17,6 +17,7 @@
 #include <linux/types.h>
 #include <linux/sched.h>
 #include <linux/sched/debug.h>
+#include <linux/sched/task.h>
 #include <linux/mm_types.h>
 #include <linux/kernel.h>
 #include <linux/errno.h>
@@ -106,7 +107,7 @@
 	dump(fp);
 
 	spin_unlock_irq(&die_lock);
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 static int kstack_depth_to_print = 24;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/h8300/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/h8300/mm/fault.c
@@ -51,7 +51,7 @@
 	printk(" at virtual address %08lx\n", address);
 	if (!user_mode(regs))
 		die("Oops", regs, error_code);
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/include/asm/cmpxchg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/include/asm/cmpxchg.h
@@ -56,7 +56,7 @@
 	__typeof__(ptr) __ptr = (ptr);				\
 	__typeof__(*(ptr)) __old = (old);			\
 	__typeof__(*(ptr)) __new = (new);			\
-	__typeof__(*(ptr)) __oldval = 0;			\
+	__typeof__(*(ptr)) __oldval = (__typeof__(*(ptr))) 0;	\
 								\
 	asm volatile(						\
 		"1:	%0 = memw_locked(%1);\n"		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/include/asm/syscalls.h
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/include/asm/syscalls.h
@@ -0,0 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#include <asm-generic/syscalls.h>
+
+asmlinkage long sys_hexagon_fadvise64_64(int fd, int advice,
+	                                  u32 a2, u32 a3, u32 a4, u32 a5);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/include/asm/timex.h
@@ -7,11 +7,10 @@
 #define _ASM_TIMEX_H
 
 #include <asm-generic/timex.h>
-#include <asm/timer-regs.h>
 #include <asm/hexagon_vm.h>
 
 /* Using TCX0 as our clock.  CLOCK_TICK_RATE scheduled to be removed. */
-#define CLOCK_TICK_RATE              TCX0_CLK_RATE
+#define CLOCK_TICK_RATE              19200
 
 #define ARCH_HAS_READ_CURRENT_TIMER
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/include/asm/uaccess.h
@@ -25,17 +25,17 @@
  * Returns true (nonzero) if the memory block *may* be valid, false (zero)
  * if it is definitely invalid.
  *
- * User address space in Hexagon, like x86, goes to 0xbfffffff, so the
- * simple MSB-based tests used by MIPS won't work.  Some further
- * optimization is probably possible here, but for now, keep it
- * reasonably simple and not *too* slow.  After all, we've got the
- * MMU for backup.
  */
+#define uaccess_kernel() (get_fs().seg == KERNEL_DS.seg)
+#define user_addr_max() (uaccess_kernel() ? ~0UL : TASK_SIZE)
 
-#define __access_ok(addr, size) \
-	((get_fs().seg == KERNEL_DS.seg) || \
-	(((unsigned long)addr < get_fs().seg) && \
-	  (unsigned long)size < (get_fs().seg - (unsigned long)addr)))
+static inline int __access_ok(unsigned long addr, unsigned long size)
+{
+	unsigned long limit = TASK_SIZE;
+
+	return (size <= limit) && (addr <= (limit - size));
+}
+#define __access_ok __access_ok
 
 /*
  * When a kernel-mode page fault is taken, the faulting instruction
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/include/uapi/asm/unistd.h
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/include/uapi/asm/unistd.h
@@ -36,5 +36,6 @@
 #define __ARCH_WANT_SYS_VFORK
 #define __ARCH_WANT_SYS_FORK
 #define __ARCH_WANT_TIME32_SYSCALLS
+#define __ARCH_WANT_SYNC_FILE_RANGE2
 
 #include <asm-generic/unistd.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/kernel/syscalltab.c
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/kernel/syscalltab.c
@@ -14,6 +14,13 @@
 #undef __SYSCALL
 #define __SYSCALL(nr, call) [nr] = (call),
 
+SYSCALL_DEFINE6(hexagon_fadvise64_64, int, fd, int, advice,
+		SC_ARG64(offset), SC_ARG64(len))
+{
+	return ksys_fadvise64_64(fd, SC_VAL64(loff_t, offset), SC_VAL64(loff_t, len), advice);
+}
+#define sys_fadvise64_64 sys_hexagon_fadvise64_64
+
 void *sys_call_table[__NR_syscalls] = {
 #include <asm/unistd.h>
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/kernel/time.c
@@ -17,9 +17,10 @@
 #include <linux/of_irq.h>
 #include <linux/module.h>
 
-#include <asm/timer-regs.h>
 #include <asm/hexagon_vm.h>
 
+#define TIMER_ENABLE		BIT(0)
+
 /*
  * For the clocksource we need:
  *	pcycle frequency (600MHz)
@@ -33,6 +34,13 @@
 cycles_t	thread_freq_mhz;
 cycles_t	sleep_clk_freq;
 
+/*
+ * 8x50 HDD Specs 5-8.  Simulator co-sim not fixed until
+ * release 1.1, and then it's "adjustable" and probably not defaulted.
+ */
+#define RTOS_TIMER_INT		3
+#define RTOS_TIMER_REGS_ADDR	0xAB000000UL
+
 static struct resource rtos_timer_resources[] = {
 	{
 		.start	= RTOS_TIMER_REGS_ADDR,
@@ -80,7 +88,7 @@
 	iowrite32(0, &rtos_timer->clear);
 
 	iowrite32(delta, &rtos_timer->match);
-	iowrite32(1 << TIMER_ENABLE, &rtos_timer->enable);
+	iowrite32(TIMER_ENABLE, &rtos_timer->enable);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/kernel/traps.c
@@ -195,8 +195,10 @@
 	printk(KERN_EMERG "Oops: %s[#%d]:\n", str, ++die.counter);
 
 	if (notify_die(DIE_OOPS, str, regs, err, pt_cause(regs), SIGSEGV) ==
-	    NOTIFY_STOP)
+	    NOTIFY_STOP) {
+		spin_unlock_irq(&die.lock);
 		return 1;
+	}
 
 	print_modules();
 	show_regs(regs);
@@ -214,7 +216,7 @@
 		panic("Fatal exception");
 
 	oops_exit();
-	do_exit(err);
+	make_task_dead(err);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/kernel/vmlinux.lds.S
@@ -64,6 +64,7 @@
 	STABS_DEBUG
 	DWARF_DEBUG
 	ELF_DETAILS
+	.hexagon.attributes 0 : { *(.hexagon.attributes) }
 
 	DISCARDS
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/hexagon/lib/io.c
+++ linux-xilinx-zynqmp-5.15.0/arch/hexagon/lib/io.c
@@ -27,6 +27,7 @@
 		*dst++ = *src;
 
 }
+EXPORT_SYMBOL(__raw_readsw);
 
 /*
  * __raw_writesw - read words a short at a time
@@ -47,6 +48,7 @@
 
 
 }
+EXPORT_SYMBOL(__raw_writesw);
 
 /*  Pretty sure len is pre-adjusted for the length of the access already */
 void __raw_readsl(const void __iomem *addr, void *data, int len)
@@ -62,6 +64,7 @@
 
 
 }
+EXPORT_SYMBOL(__raw_readsl);
 
 void __raw_writesl(void __iomem *addr, const void *data, int len)
 {
@@ -76,3 +79,4 @@
 
 
 }
+EXPORT_SYMBOL(__raw_writesl);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/Kconfig
@@ -8,6 +8,7 @@
 
 config IA64
 	bool
+	select ARCH_HAS_CPU_FINALIZE_INIT
 	select ARCH_HAS_DMA_MARK_CLEAN
 	select ARCH_HAS_STRNCPY_FROM_USER
 	select ARCH_HAS_STRNLEN_USER
@@ -62,6 +63,7 @@
 	select PCI_MSI_ARCH_FALLBACKS if PCI_MSI
 	select SET_FS
 	select ZONE_DMA32
+	select FUNCTION_ALIGNMENT_32B
 	default y
 	help
 	  The Itanium Processor Family is Intel's 64-bit successor to
@@ -323,7 +325,7 @@
 	depends on PROC_KCORE
 
 config IA64_MCA_RECOVERY
-	tristate "MCA recovery from errors other than TLB."
+	bool "MCA recovery from errors other than TLB."
 
 config IA64_PALINFO
 	tristate "/proc/pal support"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/Kconfig.debug
@@ -39,7 +39,7 @@
 
 config IA64_DEBUG_CMPXCHG
 	bool "Turn on compare-and-exchange bug checking (slow!)"
-	depends on DEBUG_KERNEL
+	depends on DEBUG_KERNEL && PRINTK
 	help
 	  Selecting this option turns on bug checking for the IA-64
 	  compare-and-exchange instructions.  This is slow!  Itaniums
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/Makefile
@@ -23,7 +23,7 @@
 EXTRA		:=
 
 cflags-y	:= -pipe $(EXTRA) -ffixed-r13 -mfixed-range=f12-f15,f32-f127 \
-		   -falign-functions=32 -frename-registers -fno-optimize-sibling-calls
+		   -frename-registers -fno-optimize-sibling-calls
 KBUILD_CFLAGS_KERNEL := -mconstant-gp
 
 GAS_STATUS	= $(shell $(srctree)/arch/ia64/scripts/check-gas "$(CC)" "$(OBJDUMP)")
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/include/asm/processor.h
@@ -542,7 +542,7 @@
 {
 	unsigned int reg = vector / 64;
 	unsigned int bit = vector % 64;
-	u64 irr;
+	unsigned long irr;
 
 	switch (reg) {
 	case 0: irr = ia64_getreg(_IA64_REG_CR_IRR0); break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/include/asm/timex.h
@@ -39,6 +39,7 @@
 	ret = ia64_getreg(_IA64_REG_AR_ITC);
 	return ret;
 }
+#define get_cycles get_cycles
 
 extern void ia64_cpu_local_tick (void);
 extern unsigned long long ia64_native_sched_clock (void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/iosapic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/iosapic.c
@@ -834,7 +834,7 @@
 	if (iosapic_intr_info[irq].count == 0) {
 #ifdef CONFIG_SMP
 		/* Clear affinity */
-		cpumask_setall(irq_get_affinity_mask(irq));
+		irq_data_update_affinity(irq_get_irq_data(irq), cpu_all_mask);
 #endif
 		/* Clear the interrupt information */
 		iosapic_intr_info[irq].dest = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/irq.c
@@ -57,8 +57,8 @@
 void set_irq_affinity_info (unsigned int irq, int hwid, int redir)
 {
 	if (irq < NR_IRQS) {
-		cpumask_copy(irq_get_affinity_mask(irq),
-			     cpumask_of(cpu_logical_id(hwid)));
+		irq_data_update_affinity(irq_get_irq_data(irq),
+					 cpumask_of(cpu_logical_id(hwid)));
 		irq_redir[irq] = (char) (redir & 0xff);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/kprobes.c
@@ -392,13 +392,13 @@
 	__this_cpu_write(current_kprobe, p);
 }
 
-static void kretprobe_trampoline(void)
+void __kretprobe_trampoline(void)
 {
 }
 
 int __kprobes trampoline_probe_handler(struct kprobe *p, struct pt_regs *regs)
 {
-	regs->cr_iip = __kretprobe_trampoline_handler(regs, kretprobe_trampoline, NULL);
+	regs->cr_iip = __kretprobe_trampoline_handler(regs, NULL);
 	/*
 	 * By returning a non-zero value, we are telling
 	 * kprobe_handler() that we don't want the post_handler
@@ -414,7 +414,7 @@
 	ri->fp = NULL;
 
 	/* Replace the return addr with trampoline addr */
-	regs->b0 = ((struct fnptr *)kretprobe_trampoline)->ip;
+	regs->b0 = (unsigned long)dereference_function_descriptor(__kretprobe_trampoline);
 }
 
 /* Check the instruction in the slot is break */
@@ -902,14 +902,14 @@
 int __init arch_init_kprobes(void)
 {
 	trampoline_p.addr =
-		(kprobe_opcode_t *)((struct fnptr *)kretprobe_trampoline)->ip;
+		dereference_function_descriptor(__kretprobe_trampoline);
 	return register_kprobe(&trampoline_p);
 }
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
 {
 	if (p->addr ==
-		(kprobe_opcode_t *)((struct fnptr *)kretprobe_trampoline)->ip)
+		dereference_function_descriptor(__kretprobe_trampoline))
 		return 1;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/mca_drv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/mca_drv.c
@@ -176,7 +176,7 @@
 	spin_unlock(&mca_bh_lock);
 
 	/* This process is about to be killed itself */
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/msi_ia64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/msi_ia64.c
@@ -37,7 +37,7 @@
 	msg.data = data;
 
 	pci_write_msi_msg(irq, &msg);
-	cpumask_copy(irq_data_get_affinity_mask(idata), cpumask_of(cpu));
+	irq_data_update_affinity(idata, cpumask_of(cpu));
 
 	return 0;
 }
@@ -132,7 +132,7 @@
 	msg.address_lo |= MSI_ADDR_DEST_ID_CPU(cpu_physical_id(cpu));
 
 	dmar_msi_write(irq, &msg);
-	cpumask_copy(irq_data_get_affinity_mask(data), mask);
+	irq_data_update_affinity(data, mask);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/salinfo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/salinfo.c
@@ -581,7 +581,7 @@
  * 'data' contains an integer that corresponds to the feature we're
  * testing
  */
-static int proc_salinfo_show(struct seq_file *m, void *v)
+static int __maybe_unused proc_salinfo_show(struct seq_file *m, void *v)
 {
 	unsigned long data = (unsigned long)v;
 	seq_puts(m, (sal_platform_features & data) ? "1\n" : "0\n");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/setup.c
@@ -1070,8 +1070,7 @@
 	}
 }
 
-void __init
-check_bugs (void)
+void __init arch_cpu_finalize_init(void)
 {
 	ia64_patch_mckinley_e9((unsigned long) __start___mckinley_e9_bundles,
 			       (unsigned long) __end___mckinley_e9_bundles);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/kernel/traps.c
@@ -85,7 +85,7 @@
 	if (panic_on_oops)
 		panic("Fatal exception");
 
-  	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/mm/contig.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/mm/contig.c
@@ -77,7 +77,7 @@
 	return __per_cpu_start + __per_cpu_offset[smp_processor_id()];
 }
 
-static inline void
+static inline __init void
 alloc_per_cpu_data(void)
 {
 	size_t size = PERCPU_PAGE_SIZE * num_possible_cpus();
@@ -153,7 +153,7 @@
 	efi_memmap_walk(find_max_min_low_pfn, NULL);
 	max_pfn = max_low_pfn;
 
-	memblock_add_node(0, PFN_PHYS(max_low_pfn), 0);
+	memblock_add_node(0, PFN_PHYS(max_low_pfn), 0, MEMBLOCK_NONE);
 
 	find_initrd();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/mm/fault.c
@@ -259,7 +259,7 @@
 		regs = NULL;
 	bust_spinlocks(0);
 	if (regs)
-		do_exit(SIGKILL);
+		make_task_dead(SIGKILL);
 	return;
 
   out_of_memory:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/mm/hugetlbpage.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/mm/hugetlbpage.c
@@ -58,7 +58,7 @@
 
 	pgd = pgd_offset(mm, taddr);
 	if (pgd_present(*pgd)) {
-		p4d = p4d_offset(pgd, addr);
+		p4d = p4d_offset(pgd, taddr);
 		if (p4d_present(*p4d)) {
 			pud = pud_offset(p4d, taddr);
 			if (pud_present(*pud)) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/mm/init.c
@@ -378,7 +378,7 @@
 #endif
 
 	if (start < end)
-		memblock_add_node(__pa(start), end - start, nid);
+		memblock_add_node(__pa(start), end - start, nid, MEMBLOCK_NONE);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/mm/numa.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/mm/numa.c
@@ -75,5 +75,6 @@
 		return 0;
 	return nid;
 }
+EXPORT_SYMBOL(memory_add_physaddr_to_nid);
 #endif
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/ia64/pci/fixup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/ia64/pci/fixup.c
@@ -76,5 +76,5 @@
 		}
 	}
 }
-DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
-				PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_ANY_ID, PCI_ANY_ID,
+			       PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/68000/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/68000/entry.S
@@ -45,6 +45,8 @@
 	jbsr	syscall_trace_enter
 	RESTORE_SWITCH_STACK
 	addql	#4,%sp
+	addql	#1,%d0
+	jeq	ret_from_exception
 	movel	%sp@(PT_OFF_ORIG_D0),%d1
 	movel	#-ENOSYS,%d0
 	cmpl	#NR_syscalls,%d1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/Kconfig
@@ -4,6 +4,7 @@
 	default y
 	select ARCH_32BIT_OFF_T
 	select ARCH_HAS_BINFMT_FLAT
+	select ARCH_HAS_CPU_FINALIZE_INIT if MMU
 	select ARCH_HAS_DMA_PREP_COHERENT if HAS_DMA && MMU && !COLDFIRE
 	select ARCH_HAS_SYNC_DMA_FOR_DEVICE if HAS_DMA
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG if RMW_INSNS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/Kconfig.cpu
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/Kconfig.cpu
@@ -338,7 +338,7 @@
 
 config M68KFPU_EMU
 	bool "Math emulation support"
-	depends on MMU
+	depends on M68KCLASSIC && FPU
 	help
 	  At some point in the future, this will cause floating-point math
 	  instructions to be emulated by the kernel on machines that lack a
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/Kconfig.devices
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/Kconfig.devices
@@ -19,6 +19,7 @@
 # We have a dedicated heartbeat LED. :-)
 config PROC_HARDWARE
 	bool "/proc/hardware support"
+	depends on PROC_FS
 	help
 	  Say Y here to support the /proc/hardware file, which gives you
 	  access to information about the machine you're running on,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/Kconfig.machine
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/Kconfig.machine
@@ -203,6 +203,7 @@
 config MEMORY_RESERVE
 	int "Memory reservation (MiB)"
 	depends on (UCSIMM || UCDIMM)
+	default 0
 	help
 	  Reserve certain memory regions on 68x328 based boards.
 
@@ -334,6 +335,7 @@
 
 config UBOOT
 	bool "Support for U-Boot command line parameters"
+	depends on COLDFIRE
 	help
 	  If you say Y here kernel will try to collect command
 	  line parameters from the initial u-boot stack.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/amiga/config.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/amiga/config.c
@@ -179,6 +179,15 @@
 			dev->slotsize = be16_to_cpu(cd->cd_SlotSize);
 			dev->boardaddr = be32_to_cpu(cd->cd_BoardAddr);
 			dev->boardsize = be32_to_cpu(cd->cd_BoardSize);
+
+			/* CS-LAB Warp 1260 workaround */
+			if (be16_to_cpu(dev->rom.er_Manufacturer) == ZORRO_MANUF(ZORRO_PROD_CSLAB_WARP_1260) &&
+			    dev->rom.er_Product == ZORRO_PROD(ZORRO_PROD_CSLAB_WARP_1260)) {
+
+				/* turn off all interrupts */
+				pr_info("Warp 1260 card detected: applying interrupt storm workaround\n");
+				*(uint32_t *)(dev->boardaddr + 0x1000) = 0xfff;
+			}
 		} else
 			pr_warn("amiga_parse_bootinfo: too many AutoConfig devices\n");
 #endif /* CONFIG_ZORRO */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/atari/ataints.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/atari/ataints.c
@@ -302,11 +302,7 @@
 
 	if (ATARIHW_PRESENT(SCU)) {
 		/* init the SCU if present */
-		tt_scu.sys_mask = 0x10;		/* enable VBL (for the cursor) and
-									 * disable HSYNC interrupts (who
-									 * needs them?)  MFP and SCC are
-									 * enabled in VME mask
-									 */
+		tt_scu.sys_mask = 0x0;		/* disable all interrupts */
 		tt_scu.vme_mask = 0x60;		/* enable MFP and SCC ints */
 	} else {
 		/* If no SCU and no Hades, the HSYNC interrupt needs to be
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/coldfire/device.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/coldfire/device.c
@@ -93,7 +93,7 @@
 	.dev.platform_data	= mcf_uart_platform_data,
 };
 
-#if IS_ENABLED(CONFIG_FEC)
+#ifdef MCFFEC_BASE0
 
 #ifdef CONFIG_M5441x
 #define FEC_NAME	"enet-fec"
@@ -145,6 +145,7 @@
 		.platform_data		= FEC_PDATA,
 	}
 };
+#endif /* MCFFEC_BASE0 */
 
 #ifdef MCFFEC_BASE1
 static struct resource mcf_fec1_resources[] = {
@@ -182,7 +183,6 @@
 	}
 };
 #endif /* MCFFEC_BASE1 */
-#endif /* CONFIG_FEC */
 
 #if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
 /*
@@ -480,7 +480,7 @@
 #endif /* MCFI2C_BASE5 */
 #endif /* IS_ENABLED(CONFIG_I2C_IMX) */
 
-#if IS_ENABLED(CONFIG_MCF_EDMA)
+#ifdef MCFEDMA_BASE
 
 static const struct dma_slave_map mcf_edma_map[] = {
 	{ "dreq0", "rx-tx", MCF_EDMA_FILTER_PARAM(0) },
@@ -552,7 +552,7 @@
 		.platform_data = &mcf_edma_data,
 	}
 };
-#endif /* IS_ENABLED(CONFIG_MCF_EDMA) */
+#endif /* MCFEDMA_BASE */
 
 #ifdef MCFSDHC_BASE
 static struct mcf_esdhc_platform_data mcf_esdhc_data = {
@@ -581,7 +581,7 @@
 };
 #endif /* MCFSDHC_BASE */
 
-#if IS_ENABLED(CONFIG_CAN_FLEXCAN)
+#ifdef MCFFLEXCAN_SIZE
 
 #include <linux/can/platform/flexcan.h>
 
@@ -620,16 +620,16 @@
 	.resource = mcf5441x_flexcan0_resource,
 	.dev.platform_data = &mcf5441x_flexcan_info,
 };
-#endif /* IS_ENABLED(CONFIG_CAN_FLEXCAN) */
+#endif /* MCFFLEXCAN_SIZE */
 
 static struct platform_device *mcf_devices[] __initdata = {
 	&mcf_uart,
-#if IS_ENABLED(CONFIG_FEC)
+#ifdef MCFFEC_BASE0
 	&mcf_fec0,
+#endif
 #ifdef MCFFEC_BASE1
 	&mcf_fec1,
 #endif
-#endif
 #if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
 	&mcf_qspi,
 #endif
@@ -651,13 +651,13 @@
 	&mcf_i2c5,
 #endif
 #endif
-#if IS_ENABLED(CONFIG_MCF_EDMA)
+#ifdef MCFEDMA_BASE
 	&mcf_edma,
 #endif
 #ifdef MCFSDHC_BASE
 	&mcf_esdhc,
 #endif
-#if IS_ENABLED(CONFIG_CAN_FLEXCAN)
+#ifdef MCFFLEXCAN_SIZE
 	&mcf_flexcan0,
 #endif
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/coldfire/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/coldfire/entry.S
@@ -90,6 +90,8 @@
 	jbsr	syscall_trace_enter
 	RESTORE_SWITCH_STACK
 	addql	#4,%sp
+	addql	#1,%d0
+	jeq	ret_from_exception
 	movel	%d3,%a0
 	jbsr	%a0@
 	movel	%d0,%sp@(PT_OFF_D0)		/* save the return value */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/fpsp040/skeleton.S
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/fpsp040/skeleton.S
@@ -499,13 +499,13 @@
 	dbf	%d0,morein
 	rts
 
-	.section .fixup,#alloc,#execinstr
+	.section .fixup,"ax"
 	.even
 1:
 	jbsr	fpsp040_die
 	jbra	.Lnotkern
 
-	.section __ex_table,#alloc
+	.section __ex_table,"a"
 	.align	4
 
 	.long	in_ea,1b
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/ifpsp060/os.S
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/ifpsp060/os.S
@@ -379,11 +379,11 @@
 
 
 | Execption handling for movs access to illegal memory
-	.section .fixup,#alloc,#execinstr
+	.section .fixup,"ax"
 	.even
 1:	moveq		#-1,%d1
 	rts
-.section __ex_table,#alloc
+.section __ex_table,"a"
 	.align 4
 	.long	dmrbuae,1b
 	.long	dmrwuae,1b
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/cmpxchg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/cmpxchg.h
@@ -33,7 +33,7 @@
 		x = tmp;
 		break;
 	default:
-		tmp = __invalid_xchg_size(x, ptr, size);
+		x = __invalid_xchg_size(x, ptr, size);
 		break;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/mcfgpio.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/mcfgpio.h
@@ -144,7 +144,7 @@
  * read-modify-write as well as those controlled by the EPORT and GPIO modules.
  */
 #define MCFGPIO_SCR_START		40
-#elif defined(CONFIGM5441x)
+#elif defined(CONFIG_M5441x)
 /* The m5441x EPORT doesn't have its own GPIO port, uses PORT C */
 #define MCFGPIO_SCR_START		0
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/mvme147hw.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/mvme147hw.h
@@ -93,8 +93,8 @@
 #define M147_SCC_B_ADDR		0xfffe3000
 #define M147_SCC_PCLK		5000000
 
-#define MVME147_IRQ_SCSI_PORT	(IRQ_USER+0x45)
-#define MVME147_IRQ_SCSI_DMA	(IRQ_USER+0x46)
+#define MVME147_IRQ_SCSI_PORT	(IRQ_USER + 5)
+#define MVME147_IRQ_SCSI_DMA	(IRQ_USER + 6)
 
 /* SCC interrupts, for MVME147 */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/pgtable_no.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/pgtable_no.h
@@ -42,7 +42,8 @@
  * ZERO_PAGE is a global shared page that is always zero: used
  * for zero-mapped memory areas etc..
  */
-#define ZERO_PAGE(vaddr)	(virt_to_page(0))
+extern void *empty_zero_page;
+#define ZERO_PAGE(vaddr)	(virt_to_page(empty_zero_page))
 
 /*
  * All 32bit addresses are effectively valid for vmalloc...
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/raw_io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/raw_io.h
@@ -80,14 +80,14 @@
 	({ u16 __v = le16_to_cpu(*(__force volatile u16 *) (addr)); __v; })
 
 #define rom_out_8(addr, b)	\
-	({u8 __maybe_unused __w, __v = (b);  u32 _addr = ((u32) (addr)); \
+	(void)({u8 __maybe_unused __w, __v = (b);  u32 _addr = ((u32) (addr)); \
 	__w = ((*(__force volatile u8 *)  ((_addr | 0x10000) + (__v<<1)))); })
 #define rom_out_be16(addr, w)	\
-	({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
+	(void)({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
 	__w = ((*(__force volatile u16 *) ((_addr & 0xFFFF0000UL) + ((__v & 0xFF)<<1)))); \
 	__w = ((*(__force volatile u16 *) ((_addr | 0x10000) + ((__v >> 8)<<1)))); })
 #define rom_out_le16(addr, w)	\
-	({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
+	(void)({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
 	__w = ((*(__force volatile u16 *) ((_addr & 0xFFFF0000UL) + ((__v >> 8)<<1)))); \
 	__w = ((*(__force volatile u16 *) ((_addr | 0x10000) + ((__v & 0xFF)<<1)))); })
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/timex.h
@@ -35,7 +35,7 @@
 {
 	if (mach_random_get_entropy)
 		return mach_random_get_entropy();
-	return 0;
+	return random_get_entropy_fallback();
 }
 #define random_get_entropy	random_get_entropy
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/uaccess.h
@@ -12,14 +12,17 @@
 #include <asm/extable.h>
 
 /* We let the MMU do all checking */
-static inline int access_ok(const void __user *addr,
+static inline int access_ok(const void __user *ptr,
 			    unsigned long size)
 {
-	/*
-	 * XXX: for !CONFIG_CPU_HAS_ADDRESS_SPACES this really needs to check
-	 * for TASK_SIZE!
-	 */
-	return 1;
+	unsigned long limit = TASK_SIZE;
+	unsigned long addr = (unsigned long)ptr;
+
+	if (IS_ENABLED(CONFIG_CPU_HAS_ADDRESS_SPACES) ||
+	    !IS_ENABLED(CONFIG_MMU))
+		return 1;
+
+	return (size <= limit) && (addr <= (limit - size));
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/include/asm/vga.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/include/asm/vga.h
@@ -9,7 +9,7 @@
  */
 #ifndef CONFIG_PCI
 
-#include <asm/raw_io.h>
+#include <asm/io.h>
 #include <asm/kmap.h>
 
 /*
@@ -29,9 +29,9 @@
 #define inw_p(port)		0
 #define outb_p(port, val)	do { } while (0)
 #define outw(port, val)		do { } while (0)
-#define readb			raw_inb
-#define writeb			raw_outb
-#define writew			raw_outw
+#define readb			__raw_readb
+#define writeb			__raw_writeb
+#define writew			__raw_writew
 
 #endif /* CONFIG_PCI */
 #endif /* _ASM_M68K_VGA_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/early_printk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/early_printk.c
@@ -12,8 +12,9 @@
 #include <linux/string.h>
 #include <asm/setup.h>
 
-extern void mvme16x_cons_write(struct console *co,
-			       const char *str, unsigned count);
+
+#include "../mvme147/mvme147.h"
+#include "../mvme16x/mvme16x.h"
 
 asmlinkage void __init debug_cons_nputs(const char *s, unsigned n);
 
@@ -22,7 +23,9 @@
 {
 #if !(defined(CONFIG_SUN3) || defined(CONFIG_M68000) || \
       defined(CONFIG_COLDFIRE))
-	if (MACH_IS_MVME16x)
+	if (MACH_IS_MVME147)
+		mvme147_scc_write(c, s, n);
+	else if (MACH_IS_MVME16x)
 		mvme16x_cons_write(c, s, n);
 	else
 		debug_cons_nputs(s, n);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/entry.S
@@ -184,9 +184,12 @@
 	jbsr	syscall_trace
 	RESTORE_SWITCH_STACK
 	addql	#4,%sp
+	addql	#1,%d0			| optimization for cmpil #-1,%d0
+	jeq	ret_from_syscall
 	movel	%sp@(PT_OFF_ORIG_D0),%d0
 	cmpl	#NR_syscalls,%d0
 	jcs	syscall
+	jra	ret_from_syscall
 badsys:
 	movel	#-ENOSYS,%sp@(PT_OFF_D0)
 	jra	ret_from_syscall
@@ -427,7 +430,9 @@
 	movec	%a0,%dfc
 
 	/* restore status register */
-	movew	%a1@(TASK_THREAD+THREAD_SR),%sr
+	movew	%a1@(TASK_THREAD+THREAD_SR),%d0
+	oriw	#0x0700,%d0
+	movew	%d0,%sr
 
 	rts
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/process.c
@@ -116,7 +116,7 @@
 {
 	/* regs will be equal to current_pt_regs() */
 	struct kernel_clone_args args = {
-		.flags		= regs->d1 & ~CSIGNAL,
+		.flags		= (u32)(regs->d1) & ~CSIGNAL,
 		.pidfd		= (int __user *)regs->d3,
 		.child_tid	= (int __user *)regs->d4,
 		.parent_tid	= (int __user *)regs->d3,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/relocate_kernel.S
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/relocate_kernel.S
@@ -26,7 +26,7 @@
 	lea %pc@(.Lcopy),%a4
 2:	addl #0x00000000,%a4		/* virt_to_phys() */
 
-	.section ".m68k_fixup","aw"
+	.section .m68k_fixup,"aw"
 	.long M68K_FIXUP_MEMOFFSET, 2b+2
 	.previous
 
@@ -49,7 +49,7 @@
 	lea %pc@(.Lcont040),%a4
 5:	addl #0x00000000,%a4		/* virt_to_phys() */
 
-	.section ".m68k_fixup","aw"
+	.section .m68k_fixup,"aw"
 	.long M68K_FIXUP_MEMOFFSET, 5b+2
 	.previous
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/setup_mm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/setup_mm.c
@@ -10,6 +10,7 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/cpu.h>
 #include <linux/mm.h>
 #include <linux/sched.h>
 #include <linux/delay.h>
@@ -87,15 +88,8 @@
 void (*mach_init_IRQ) (void) __initdata = NULL;
 void (*mach_get_model) (char *model);
 void (*mach_get_hardware_list) (struct seq_file *m);
-/* machine dependent timer functions */
-int (*mach_hwclk) (int, struct rtc_time*);
-EXPORT_SYMBOL(mach_hwclk);
 unsigned int (*mach_get_ss)(void);
-int (*mach_get_rtc_pll)(struct rtc_pll_info *);
-int (*mach_set_rtc_pll)(struct rtc_pll_info *);
 EXPORT_SYMBOL(mach_get_ss);
-EXPORT_SYMBOL(mach_get_rtc_pll);
-EXPORT_SYMBOL(mach_set_rtc_pll);
 void (*mach_reset)( void );
 void (*mach_halt)( void );
 void (*mach_power_off)( void );
@@ -519,7 +513,7 @@
 module_init(proc_hardware_init);
 #endif
 
-void check_bugs(void)
+void __init arch_cpu_finalize_init(void)
 {
 #if defined(CONFIG_FPU) && !defined(CONFIG_M68KFPU_EMU)
 	if (m68k_fputype == 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/setup_no.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/setup_no.c
@@ -50,7 +50,6 @@
 
 /* machine dependent timer functions */
 void (*mach_sched_init)(void) __initdata = NULL;
-int (*mach_hwclk) (int, struct rtc_time*);
 
 /* machine dependent reboot functions */
 void (*mach_reset)(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/signal.c
@@ -625,6 +625,7 @@
 	/* _sigfault._perf */
 	BUILD_BUG_ON(offsetof(siginfo_t, si_perf_data) != 0x10);
 	BUILD_BUG_ON(offsetof(siginfo_t, si_perf_type) != 0x14);
+	BUILD_BUG_ON(offsetof(siginfo_t, si_perf_flags) != 0x18);
 
 	/* _sigpoll */
 	BUILD_BUG_ON(offsetof(siginfo_t, si_band)   != 0x0c);
@@ -857,11 +858,17 @@
 }
 
 static inline void __user *
-get_sigframe(struct ksignal *ksig, size_t frame_size)
+get_sigframe(struct ksignal *ksig, struct pt_regs *tregs, size_t frame_size)
 {
 	unsigned long usp = sigsp(rdusp(), ksig);
+	unsigned long gap = 0;
 
-	return (void __user *)((usp - frame_size) & -8UL);
+	if (CPU_IS_020_OR_030 && tregs->format == 0xb) {
+		/* USP is unreliable so use worst-case value */
+		gap = 256;
+	}
+
+	return (void __user *)((usp - gap - frame_size) & -8UL);
 }
 
 static int setup_frame(struct ksignal *ksig, sigset_t *set,
@@ -879,7 +886,7 @@
 		return -EFAULT;
 	}
 
-	frame = get_sigframe(ksig, sizeof(*frame) + fsize);
+	frame = get_sigframe(ksig, tregs, sizeof(*frame) + fsize);
 
 	if (fsize)
 		err |= copy_to_user (frame + 1, regs + 1, fsize);
@@ -951,7 +958,7 @@
 		return -EFAULT;
 	}
 
-	frame = get_sigframe(ksig, sizeof(*frame));
+	frame = get_sigframe(ksig, tregs, sizeof(*frame));
 
 	if (fsize)
 		err |= copy_to_user (&frame->uc.uc_extra, regs + 1, fsize);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/time.c
@@ -63,6 +63,15 @@
 #endif /* CONFIG_HEARTBEAT */
 
 #ifdef CONFIG_M68KCLASSIC
+/* machine dependent timer functions */
+int (*mach_hwclk) (int, struct rtc_time*);
+EXPORT_SYMBOL(mach_hwclk);
+
+int (*mach_get_rtc_pll)(struct rtc_pll_info *);
+int (*mach_set_rtc_pll)(struct rtc_pll_info *);
+EXPORT_SYMBOL(mach_get_rtc_pll);
+EXPORT_SYMBOL(mach_set_rtc_pll);
+
 #if !IS_BUILTIN(CONFIG_RTC_DRV_GENERIC)
 void read_persistent_clock64(struct timespec64 *ts)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/kernel/traps.c
@@ -30,6 +30,7 @@
 #include <linux/init.h>
 #include <linux/ptrace.h>
 #include <linux/kallsyms.h>
+#include <linux/extable.h>
 
 #include <asm/setup.h>
 #include <asm/fpu.h>
@@ -544,7 +545,8 @@
 			errorcode |= 2;
 
 		if (mmusr & (MMU_I | MMU_WP)) {
-			if (ssw & 4) {
+			/* We might have an exception table for this PC */
+			if (ssw & 4 && !search_exception_tables(fp->ptregs.pc)) {
 				pr_err("Data %s fault at %#010lx in %s (pc=%#lx)\n",
 				       ssw & RW ? "read" : "write",
 				       fp->un.fmtb.daddr,
@@ -1131,7 +1133,7 @@
 	pr_crit("%s: %08x\n", str, nr);
 	show_registers(fp);
 	add_taint(TAINT_DIE, LOCKDEP_NOW_UNRELIABLE);
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 asmlinkage void set_esp0(unsigned long ssp)
@@ -1145,7 +1147,7 @@
  */
 asmlinkage void fpsp040_die(void)
 {
-	force_sigsegv(SIGSEGV);
+	force_exit_sig(SIGSEGV);
 }
 
 #ifdef CONFIG_M68KFPU_EMU
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mac/misc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mac/misc.c
@@ -451,30 +451,18 @@
 
 void mac_reset(void)
 {
-	if (macintosh_config->adb_type == MAC_ADB_II &&
-	    macintosh_config->ident != MAC_MODEL_SE30) {
-		/* need ROMBASE in booter */
-		/* indeed, plus need to MAP THE ROM !! */
-
-		if (mac_bi_data.rombase == 0)
-			mac_bi_data.rombase = 0x40800000;
-
-		/* works on some */
-		rom_reset = (void *) (mac_bi_data.rombase + 0xa);
-
-		local_irq_disable();
-		rom_reset();
 #ifdef CONFIG_ADB_CUDA
-	} else if (macintosh_config->adb_type == MAC_ADB_EGRET ||
-	           macintosh_config->adb_type == MAC_ADB_CUDA) {
+	if (macintosh_config->adb_type == MAC_ADB_EGRET ||
+	    macintosh_config->adb_type == MAC_ADB_CUDA) {
 		cuda_restart();
+	} else
 #endif
 #ifdef CONFIG_ADB_PMU
-	} else if (macintosh_config->adb_type == MAC_ADB_PB2) {
+	if (macintosh_config->adb_type == MAC_ADB_PB2) {
 		pmu_restart();
+	} else
 #endif
-	} else if (CPU_IS_030) {
-
+	if (CPU_IS_030) {
 		/* 030-specific reset routine.  The idea is general, but the
 		 * specific registers to reset are '030-specific.  Until I
 		 * have a non-030 machine, I can't test anything else.
@@ -522,6 +510,18 @@
 		    "jmp %/a0@\n\t" /* jump to the reset vector */
 		    ".chip 68k"
 		    : : "r" (offset), "a" (rombase) : "a0");
+	} else {
+		/* need ROMBASE in booter */
+		/* indeed, plus need to MAP THE ROM !! */
+
+		if (mac_bi_data.rombase == 0)
+			mac_bi_data.rombase = 0x40800000;
+
+		/* works on some */
+		rom_reset = (void *)(mac_bi_data.rombase + 0xa);
+
+		local_irq_disable();
+		rom_reset();
 	}
 
 	/* should never get here */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mm/fault.c
@@ -48,7 +48,7 @@
 			pr_alert("Unable to handle kernel access");
 		pr_cont(" at virtual address %p\n", addr);
 		die_if_kernel("Oops", regs, 0 /*error_code*/);
-		do_exit(SIGKILL);
+		make_task_dead(SIGKILL);
 	}
 
 	return 1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mm/mcfmmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mm/mcfmmu.c
@@ -174,7 +174,8 @@
 	m68k_memory[0].addr = _rambase;
 	m68k_memory[0].size = _ramend - _rambase;
 
-	memblock_add_node(m68k_memory[0].addr, m68k_memory[0].size, 0);
+	memblock_add_node(m68k_memory[0].addr, m68k_memory[0].size, 0,
+			  MEMBLOCK_NONE);
 
 	/* compute total pages in system */
 	num_pages = PFN_DOWN(_ramend - _rambase);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mm/motorola.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mm/motorola.c
@@ -410,7 +410,8 @@
 
 	min_addr = m68k_memory[0].addr;
 	max_addr = min_addr + m68k_memory[0].size;
-	memblock_add_node(m68k_memory[0].addr, m68k_memory[0].size, 0);
+	memblock_add_node(m68k_memory[0].addr, m68k_memory[0].size, 0,
+			  MEMBLOCK_NONE);
 	for (i = 1; i < m68k_num_memory;) {
 		if (m68k_memory[i].addr < min_addr) {
 			printk("Ignoring memory chunk at 0x%lx:0x%lx before the first chunk\n",
@@ -421,7 +422,8 @@
 				(m68k_num_memory - i) * sizeof(struct m68k_mem_info));
 			continue;
 		}
-		memblock_add_node(m68k_memory[i].addr, m68k_memory[i].size, i);
+		memblock_add_node(m68k_memory[i].addr, m68k_memory[i].size, i,
+				  MEMBLOCK_NONE);
 		addr = m68k_memory[i].addr + m68k_memory[i].size;
 		if (addr > max_addr)
 			max_addr = addr;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mvme147/config.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mvme147/config.c
@@ -35,6 +35,7 @@
 #include <asm/machdep.h>
 #include <asm/mvme147hw.h>
 
+#include "mvme147.h"
 
 static void mvme147_get_model(char *model);
 extern void mvme147_sched_init(void);
@@ -188,3 +189,32 @@
 	}
 	return 0;
 }
+
+static void scc_delay(void)
+{
+	__asm__ __volatile__ ("nop; nop;");
+}
+
+static void scc_write(char ch)
+{
+	do {
+		scc_delay();
+	} while (!(in_8(M147_SCC_A_ADDR) & BIT(2)));
+	scc_delay();
+	out_8(M147_SCC_A_ADDR, 8);
+	scc_delay();
+	out_8(M147_SCC_A_ADDR, ch);
+}
+
+void mvme147_scc_write(struct console *co, const char *str, unsigned int count)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	while (count--)	{
+		if (*str == '\n')
+			scc_write('\r');
+		scc_write(*str++);
+	}
+	local_irq_restore(flags);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mvme147/mvme147.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mvme147/mvme147.h
@@ -0,0 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+struct console;
+
+/* config.c */
+void mvme147_scc_write(struct console *co, const char *str, unsigned int count);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mvme16x/config.c
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mvme16x/config.c
@@ -38,6 +38,8 @@
 #include <asm/machdep.h>
 #include <asm/mvme16xhw.h>
 
+#include "mvme16x.h"
+
 extern t_bdid mvme_bdid;
 
 static MK48T08ptr_t volatile rtc = (MK48T08ptr_t)MVME_RTC_BASE;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/m68k/mvme16x/mvme16x.h
+++ linux-xilinx-zynqmp-5.15.0/arch/m68k/mvme16x/mvme16x.h
@@ -0,0 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+struct console;
+
+/* config.c */
+void mvme16x_cons_write(struct console *co, const char *str, unsigned count);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/Kconfig
@@ -2,6 +2,7 @@
 config MICROBLAZE
 	def_bool y
 	select ARCH_32BIT_OFF_T
+	select ARCH_ATOMIC
 	select ARCH_NO_SWAP
 	select ARCH_HAS_DMA_PREP_COHERENT
 	select ARCH_HAS_GCOV_PROFILE_ALL
@@ -42,6 +43,8 @@
 	select CPU_NO_EFFICIENT_FFS
 	select MMU_GATHER_NO_RANGE
 	select SPARSE_IRQ
+	select GENERIC_IRQ_MULTI_HANDLER
+	select HANDLE_DOMAIN_IRQ
 	select SET_FS
 	select ZONE_DMA
 	select TRACE_IRQFLAGS_SUPPORT
@@ -62,6 +65,33 @@
 
 endchoice
 
+config SMP
+	bool "SMP support (EXPERIMENTAL)"
+	default n
+	help
+	  This option enables SMP support for MicroBlaze. Every CPU has its own
+	  BRAM connected via LMB. The BRAM is used as CPU private memory, which
+	  is one reason CPU hotplug is not yet supported.
+	  Timers and interrupt controllers are placed on the same bus and
+	  accessible by all CPUs, but every CPU is assigned one timer and one
+	  interrupt controller. There is also one free running clock source
+	  timer for the whole system. The boot CPU wakes up other CPUs by
+	  sending a wake-up software Interrupt to a specific CPU that is
+	  sleeping. Wake-up will cause a jump to DDR start address where it is
+	  assumed that the kernel is placed. There is currently no support for
+	  placing the kernel at a different location.
+
+config GENERIC_LOCKBREAK
+	bool
+	default y
+	depends on SMP && PREEMPT
+
+config NR_CPUS
+	int "Maximum number of CPUs (2-8)"
+	range 2 8
+	depends on SMP
+	default "2"
+
 config ARCH_HAS_ILOG2_U32
 	def_bool n
 
@@ -205,6 +235,16 @@
 	hex "Size of user task space" if TASK_SIZE_BOOL
 	default "0x80000000"
 
+config MB_MANAGER
+	bool "Support for Microblaze Manager"
+	depends on ADVANCED_OPTIONS
+	help
+	  This option enables API for configuring the MicroBlaze manager
+	  control register, which is consumed by the break handler to
+	  block the break.
+
+	  Say N here unless you know what you are doing.
+
 endmenu
 
 menu "Bus Options"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/boot/dts/Xilinx-KC705_SMP_4.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/boot/dts/Xilinx-KC705_SMP_4.dts
@@ -0,0 +1,806 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx KC705 SMP hw design
+ *
+ * (C) Copyright 2007-2021 Xilinx, Inc.
+ * (C) Copyright 2007-2012 Michal Simek
+ * (C) Copyright 2007-2012 PetaLogix Qld Pty Ltd
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ */
+
+/dts-v1/;
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "xlnx,microblaze";
+	model = "Xilinx MicroBlaze";
+	aliases {
+		ethernet0 = &axi_ethernet_1_axi_ethernet_buffer;
+		serial0 = &axi_uart16550_1;
+	} ;
+	chosen {
+		bootargs = "earlycon console=ttyS0,115200 maxcpus=4";
+		stdout-path = "serial0:115200n8";
+	} ;
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = < 0x80000000 0x40000000 >;
+	} ;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			clocks = <&clk_cpu>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,microblaze-10.0";
+			d-cache-baseaddr = <0x80000000>;
+			d-cache-highaddr = <0xbfffffff>;
+			d-cache-line-size = <0x20>;
+			d-cache-size = <0x8000>;
+			device_type = "cpu";
+			i-cache-baseaddr = <0x80000000>;
+			i-cache-highaddr = <0xbfffffff>;
+			i-cache-line-size = <0x20>;
+			i-cache-size = <0x8000>;
+			model = "xlnx,microblaze-10.0";
+			reg = <0>;
+			timebase-frequency = <100000000>;
+			xlnx,addr-tag-bits = <0xf>;
+			xlnx,allow-dcache-wr = <0x1>;
+			xlnx,allow-icache-wr = <0x1>;
+			xlnx,area-optimized = <0x0>;
+			xlnx,async-interrupt = <0x1>;
+			xlnx,avoid-primitives = <0x0>;
+			xlnx,base-vectors = <0x0>;
+			xlnx,branch-target-cache-size = <0x0>;
+			xlnx,cache-byte-size = <0x8000>;
+			xlnx,component-name = "kc705_smp_4_microblaze_1_0";
+			xlnx,d-axi = <0x1>;
+			xlnx,d-lmb = <0x1>;
+			xlnx,data-size = <0x20>;
+			xlnx,dcache-addr-tag = <0xf>;
+			xlnx,dcache-always-used = <0x1>;
+			xlnx,dcache-byte-size = <0x8000>;
+			xlnx,dcache-data-width = <0x0>;
+			xlnx,dcache-force-tag-lutram = <0x0>;
+			xlnx,dcache-line-len = <0x8>;
+			xlnx,dcache-use-writeback = <0x0>;
+			xlnx,dcache-victims = <0x0>;
+			xlnx,debug-enabled = <0x1>;
+			xlnx,div-zero-exception = <0x1>;
+			xlnx,dynamic-bus-sizing = <0x0>;
+			xlnx,ecc-use-ce-exception = <0x0>;
+			xlnx,edge-is-positive = <0x0>;
+			xlnx,edk-iptype = "PROCESSOR";
+			xlnx,edk-special = "microblaze";
+			xlnx,enable-discrete-ports = <0x1>;
+			xlnx,endianness = <0x1>;
+			xlnx,family = "kintex7";
+			xlnx,fault-tolerant = <0x0>;
+			xlnx,fpu-exception = <0x1>;
+			xlnx,freq = <0x5f5e100>;
+			xlnx,fsl-exception = <0x0>;
+			xlnx,fsl-links = <0x0>;
+			xlnx,g-template-list = <0x0>;
+			xlnx,g-use-exceptions = <0x1>;
+			xlnx,i-axi = <0x0>;
+			xlnx,i-lmb = <0x1>;
+			xlnx,icache-always-used = <0x1>;
+			xlnx,icache-data-width = <0x0>;
+			xlnx,icache-force-tag-lutram = <0x0>;
+			xlnx,icache-line-len = <0x8>;
+			xlnx,icache-streams = <0x0>;
+			xlnx,icache-victims = <0x0>;
+			xlnx,ill-opcode-exception = <0x1>;
+			xlnx,instance = "kc705_smp_4_microblaze_1_0";
+			xlnx,interconnect = <0x3>;
+			xlnx,interrupt-is-edge = <0x0>;
+			xlnx,lockstep-select = <0x0>;
+			xlnx,lockstep-slave = <0x0>;
+			xlnx,mmu-dtlb-size = <0x4>;
+			xlnx,mmu-itlb-size = <0x2>;
+			xlnx,mmu-privileged-instr = <0x0>;
+			xlnx,mmu-tlb-access = <0x3>;
+			xlnx,mmu-zones = <0x2>;
+			xlnx,number-of-pc-brk = <0x1>;
+			xlnx,number-of-rd-addr-brk = <0x0>;
+			xlnx,number-of-wr-addr-brk = <0x0>;
+			xlnx,opcode-0x0-illegal = <0x1>;
+			xlnx,optimization = <0x0>;
+			xlnx,pc-width = <0x20>;
+			xlnx,pvr = <0x2>;
+			xlnx,pvr-user1 = <0x0>;
+			xlnx,pvr-user2 = <0x0>;
+			xlnx,reset-msr = <0x0>;
+			xlnx,sco = <0x0>;
+			xlnx,trace = <0x0>;
+			xlnx,unaligned-exceptions = <0x1>;
+			xlnx,use-barrel = <0x1>;
+			xlnx,use-branch-target-cache = <0x0>;
+			xlnx,use-config-reset = <0x0>;
+			xlnx,use-dcache = <0x1>;
+			xlnx,use-div = <0x1>;
+			xlnx,use-ext-brk = <0x0>;
+			xlnx,use-ext-nm-brk = <0x0>;
+			xlnx,use-extended-fsl-instr = <0x0>;
+			xlnx,use-fpu = <0x2>;
+			xlnx,use-hw-mul = <0x2>;
+			xlnx,use-icache = <0x1>;
+			xlnx,use-interrupt = <0x1>;
+			xlnx,use-mmu = <0x3>;
+			xlnx,use-msr-instr = <0x1>;
+			xlnx,use-pcmp-instr = <0x1>;
+			xlnx,use-reorder-instr = <0x1>;
+			xlnx,use-stack-protection = <0x0>;
+		} ;
+		cpu@1 {
+			clocks = <&clk_cpu>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,microblaze-10.0";
+			d-cache-baseaddr = <0x80000000>;
+			d-cache-highaddr = <0xbfffffff>;
+			d-cache-line-size = <0x20>;
+			d-cache-size = <0x8000>;
+			device_type = "cpu";
+			i-cache-baseaddr = <0x80000000>;
+			i-cache-highaddr = <0xbfffffff>;
+			i-cache-line-size = <0x20>;
+			i-cache-size = <0x8000>;
+			model = "xlnx,microblaze-10.0";
+			reg = <1>;
+			timebase-frequency = <100000000>;
+			xlnx,addr-tag-bits = <0xf>;
+			xlnx,allow-dcache-wr = <0x1>;
+			xlnx,allow-icache-wr = <0x1>;
+			xlnx,area-optimized = <0x0>;
+			xlnx,async-interrupt = <0x1>;
+			xlnx,avoid-primitives = <0x0>;
+			xlnx,base-vectors = <0x0>;
+			xlnx,branch-target-cache-size = <0x0>;
+			xlnx,cache-byte-size = <0x8000>;
+			xlnx,component-name = "kc705_smp_4_microblaze_1_0";
+			xlnx,d-axi = <0x1>;
+			xlnx,d-lmb = <0x1>;
+			xlnx,data-size = <0x20>;
+			xlnx,dcache-addr-tag = <0xf>;
+			xlnx,dcache-always-used = <0x1>;
+			xlnx,dcache-byte-size = <0x8000>;
+			xlnx,dcache-data-width = <0x0>;
+			xlnx,dcache-force-tag-lutram = <0x0>;
+			xlnx,dcache-line-len = <0x8>;
+			xlnx,dcache-use-writeback = <0x0>;
+			xlnx,dcache-victims = <0x0>;
+			xlnx,debug-enabled = <0x1>;
+			xlnx,div-zero-exception = <0x1>;
+			xlnx,dynamic-bus-sizing = <0x0>;
+			xlnx,ecc-use-ce-exception = <0x0>;
+			xlnx,edge-is-positive = <0x0>;
+			xlnx,edk-iptype = "PROCESSOR";
+			xlnx,edk-special = "microblaze";
+			xlnx,enable-discrete-ports = <0x1>;
+			xlnx,endianness = <0x1>;
+			xlnx,family = "kintex7";
+			xlnx,fault-tolerant = <0x0>;
+			xlnx,fpu-exception = <0x1>;
+			xlnx,freq = <0x5f5e100>;
+			xlnx,fsl-exception = <0x0>;
+			xlnx,fsl-links = <0x0>;
+			xlnx,g-template-list = <0x0>;
+			xlnx,g-use-exceptions = <0x1>;
+			xlnx,i-axi = <0x0>;
+			xlnx,i-lmb = <0x1>;
+			xlnx,icache-always-used = <0x1>;
+			xlnx,icache-data-width = <0x0>;
+			xlnx,icache-force-tag-lutram = <0x0>;
+			xlnx,icache-line-len = <0x8>;
+			xlnx,icache-streams = <0x0>;
+			xlnx,icache-victims = <0x0>;
+			xlnx,ill-opcode-exception = <0x1>;
+			xlnx,instance = "kc705_smp_4_microblaze_1_0";
+			xlnx,interconnect = <0x3>;
+			xlnx,interrupt-is-edge = <0x0>;
+			xlnx,lockstep-select = <0x0>;
+			xlnx,lockstep-slave = <0x0>;
+			xlnx,mmu-dtlb-size = <0x4>;
+			xlnx,mmu-itlb-size = <0x2>;
+			xlnx,mmu-privileged-instr = <0x0>;
+			xlnx,mmu-tlb-access = <0x3>;
+			xlnx,mmu-zones = <0x2>;
+			xlnx,number-of-pc-brk = <0x1>;
+			xlnx,number-of-rd-addr-brk = <0x0>;
+			xlnx,number-of-wr-addr-brk = <0x0>;
+			xlnx,opcode-0x0-illegal = <0x1>;
+			xlnx,optimization = <0x0>;
+			xlnx,pc-width = <0x20>;
+			xlnx,pvr = <0x2>;
+			xlnx,pvr-user1 = <0x1>;
+			xlnx,pvr-user2 = <0x0>;
+			xlnx,reset-msr = <0x0>;
+			xlnx,sco = <0x0>;
+			xlnx,trace = <0x0>;
+			xlnx,unaligned-exceptions = <0x1>;
+			xlnx,use-barrel = <0x1>;
+			xlnx,use-branch-target-cache = <0x0>;
+			xlnx,use-config-reset = <0x0>;
+			xlnx,use-dcache = <0x1>;
+			xlnx,use-div = <0x1>;
+			xlnx,use-ext-brk = <0x0>;
+			xlnx,use-ext-nm-brk = <0x0>;
+			xlnx,use-extended-fsl-instr = <0x0>;
+			xlnx,use-fpu = <0x2>;
+			xlnx,use-hw-mul = <0x2>;
+			xlnx,use-icache = <0x1>;
+			xlnx,use-interrupt = <0x1>;
+			xlnx,use-mmu = <0x3>;
+			xlnx,use-msr-instr = <0x1>;
+			xlnx,use-pcmp-instr = <0x1>;
+			xlnx,use-reorder-instr = <0x1>;
+			xlnx,use-stack-protection = <0x0>;
+		} ;
+		cpu@2 {
+			clocks = <&clk_cpu>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,microblaze-10.0";
+			d-cache-baseaddr = <0x80000000>;
+			d-cache-highaddr = <0xbfffffff>;
+			d-cache-line-size = <0x20>;
+			d-cache-size = <0x8000>;
+			device_type = "cpu";
+			i-cache-baseaddr = <0x80000000>;
+			i-cache-highaddr = <0xbfffffff>;
+			i-cache-line-size = <0x20>;
+			i-cache-size = <0x8000>;
+			model = "xlnx,microblaze-10.0";
+			reg = <2>;
+			timebase-frequency = <100000000>;
+			xlnx,addr-tag-bits = <0xf>;
+			xlnx,allow-dcache-wr = <0x1>;
+			xlnx,allow-icache-wr = <0x1>;
+			xlnx,area-optimized = <0x0>;
+			xlnx,async-interrupt = <0x1>;
+			xlnx,avoid-primitives = <0x0>;
+			xlnx,base-vectors = <0x0>;
+			xlnx,branch-target-cache-size = <0x0>;
+			xlnx,cache-byte-size = <0x8000>;
+			xlnx,component-name = "kc705_smp_4_microblaze_1_0";
+			xlnx,d-axi = <0x1>;
+			xlnx,d-lmb = <0x1>;
+			xlnx,data-size = <0x20>;
+			xlnx,dcache-addr-tag = <0xf>;
+			xlnx,dcache-always-used = <0x1>;
+			xlnx,dcache-byte-size = <0x8000>;
+			xlnx,dcache-data-width = <0x0>;
+			xlnx,dcache-force-tag-lutram = <0x0>;
+			xlnx,dcache-line-len = <0x8>;
+			xlnx,dcache-use-writeback = <0x0>;
+			xlnx,dcache-victims = <0x0>;
+			xlnx,debug-enabled = <0x1>;
+			xlnx,div-zero-exception = <0x1>;
+			xlnx,dynamic-bus-sizing = <0x0>;
+			xlnx,ecc-use-ce-exception = <0x0>;
+			xlnx,edge-is-positive = <0x0>;
+			xlnx,edk-iptype = "PROCESSOR";
+			xlnx,edk-special = "microblaze";
+			xlnx,enable-discrete-ports = <0x1>;
+			xlnx,endianness = <0x1>;
+			xlnx,family = "kintex7";
+			xlnx,fault-tolerant = <0x0>;
+			xlnx,fpu-exception = <0x1>;
+			xlnx,freq = <0x5f5e100>;
+			xlnx,fsl-exception = <0x0>;
+			xlnx,fsl-links = <0x0>;
+			xlnx,g-template-list = <0x0>;
+			xlnx,g-use-exceptions = <0x1>;
+			xlnx,i-axi = <0x0>;
+			xlnx,i-lmb = <0x1>;
+			xlnx,icache-always-used = <0x1>;
+			xlnx,icache-data-width = <0x0>;
+			xlnx,icache-force-tag-lutram = <0x0>;
+			xlnx,icache-line-len = <0x8>;
+			xlnx,icache-streams = <0x0>;
+			xlnx,icache-victims = <0x0>;
+			xlnx,ill-opcode-exception = <0x1>;
+			xlnx,instance = "kc705_smp_4_microblaze_1_0";
+			xlnx,interconnect = <0x3>;
+			xlnx,interrupt-is-edge = <0x0>;
+			xlnx,lockstep-select = <0x0>;
+			xlnx,lockstep-slave = <0x0>;
+			xlnx,mmu-dtlb-size = <0x4>;
+			xlnx,mmu-itlb-size = <0x2>;
+			xlnx,mmu-privileged-instr = <0x0>;
+			xlnx,mmu-tlb-access = <0x3>;
+			xlnx,mmu-zones = <0x2>;
+			xlnx,number-of-pc-brk = <0x1>;
+			xlnx,number-of-rd-addr-brk = <0x0>;
+			xlnx,number-of-wr-addr-brk = <0x0>;
+			xlnx,opcode-0x0-illegal = <0x1>;
+			xlnx,optimization = <0x0>;
+			xlnx,pc-width = <0x20>;
+			xlnx,pvr = <0x2>;
+			xlnx,pvr-user1 = <0x2>;
+			xlnx,pvr-user2 = <0x0>;
+			xlnx,reset-msr = <0x0>;
+			xlnx,sco = <0x0>;
+			xlnx,trace = <0x0>;
+			xlnx,unaligned-exceptions = <0x1>;
+			xlnx,use-barrel = <0x1>;
+			xlnx,use-branch-target-cache = <0x0>;
+			xlnx,use-config-reset = <0x0>;
+			xlnx,use-dcache = <0x1>;
+			xlnx,use-div = <0x1>;
+			xlnx,use-ext-brk = <0x0>;
+			xlnx,use-ext-nm-brk = <0x0>;
+			xlnx,use-extended-fsl-instr = <0x0>;
+			xlnx,use-fpu = <0x2>;
+			xlnx,use-hw-mul = <0x2>;
+			xlnx,use-icache = <0x1>;
+			xlnx,use-interrupt = <0x1>;
+			xlnx,use-mmu = <0x3>;
+			xlnx,use-msr-instr = <0x1>;
+			xlnx,use-pcmp-instr = <0x1>;
+			xlnx,use-reorder-instr = <0x1>;
+			xlnx,use-stack-protection = <0x0>;
+		} ;
+		cpu@3 {
+			clocks = <&clk_cpu>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,microblaze-10.0";
+			d-cache-baseaddr = <0x80000000>;
+			d-cache-highaddr = <0xbfffffff>;
+			d-cache-line-size = <0x20>;
+			d-cache-size = <0x8000>;
+			device_type = "cpu";
+			i-cache-baseaddr = <0x80000000>;
+			i-cache-highaddr = <0xbfffffff>;
+			i-cache-line-size = <0x20>;
+			i-cache-size = <0x8000>;
+			model = "xlnx,microblaze-10.0";
+			reg = <3>;
+			timebase-frequency = <100000000>;
+			xlnx,addr-tag-bits = <0xf>;
+			xlnx,allow-dcache-wr = <0x1>;
+			xlnx,allow-icache-wr = <0x1>;
+			xlnx,area-optimized = <0x0>;
+			xlnx,async-interrupt = <0x1>;
+			xlnx,avoid-primitives = <0x0>;
+			xlnx,base-vectors = <0x0>;
+			xlnx,branch-target-cache-size = <0x0>;
+			xlnx,cache-byte-size = <0x8000>;
+			xlnx,component-name = "kc705_smp_4_microblaze_1_0";
+			xlnx,d-axi = <0x1>;
+			xlnx,d-lmb = <0x1>;
+			xlnx,data-size = <0x20>;
+			xlnx,dcache-addr-tag = <0xf>;
+			xlnx,dcache-always-used = <0x1>;
+			xlnx,dcache-byte-size = <0x8000>;
+			xlnx,dcache-data-width = <0x0>;
+			xlnx,dcache-force-tag-lutram = <0x0>;
+			xlnx,dcache-line-len = <0x8>;
+			xlnx,dcache-use-writeback = <0x0>;
+			xlnx,dcache-victims = <0x0>;
+			xlnx,debug-enabled = <0x1>;
+			xlnx,div-zero-exception = <0x1>;
+			xlnx,dynamic-bus-sizing = <0x0>;
+			xlnx,ecc-use-ce-exception = <0x0>;
+			xlnx,edge-is-positive = <0x0>;
+			xlnx,edk-iptype = "PROCESSOR";
+			xlnx,edk-special = "microblaze";
+			xlnx,enable-discrete-ports = <0x1>;
+			xlnx,endianness = <0x1>;
+			xlnx,family = "kintex7";
+			xlnx,fault-tolerant = <0x0>;
+			xlnx,fpu-exception = <0x1>;
+			xlnx,freq = <0x5f5e100>;
+			xlnx,fsl-exception = <0x0>;
+			xlnx,fsl-links = <0x0>;
+			xlnx,g-template-list = <0x0>;
+			xlnx,g-use-exceptions = <0x1>;
+			xlnx,i-axi = <0x0>;
+			xlnx,i-lmb = <0x1>;
+			xlnx,icache-always-used = <0x1>;
+			xlnx,icache-data-width = <0x0>;
+			xlnx,icache-force-tag-lutram = <0x0>;
+			xlnx,icache-line-len = <0x8>;
+			xlnx,icache-streams = <0x0>;
+			xlnx,icache-victims = <0x0>;
+			xlnx,ill-opcode-exception = <0x1>;
+			xlnx,instance = "kc705_smp_4_microblaze_1_0";
+			xlnx,interconnect = <0x3>;
+			xlnx,interrupt-is-edge = <0x0>;
+			xlnx,lockstep-select = <0x0>;
+			xlnx,lockstep-slave = <0x0>;
+			xlnx,mmu-dtlb-size = <0x4>;
+			xlnx,mmu-itlb-size = <0x2>;
+			xlnx,mmu-privileged-instr = <0x0>;
+			xlnx,mmu-tlb-access = <0x3>;
+			xlnx,mmu-zones = <0x2>;
+			xlnx,number-of-pc-brk = <0x1>;
+			xlnx,number-of-rd-addr-brk = <0x0>;
+			xlnx,number-of-wr-addr-brk = <0x0>;
+			xlnx,opcode-0x0-illegal = <0x1>;
+			xlnx,optimization = <0x0>;
+			xlnx,pc-width = <0x20>;
+			xlnx,pvr = <0x2>;
+			xlnx,pvr-user1 = <0x3>;
+			xlnx,pvr-user2 = <0x0>;
+			xlnx,reset-msr = <0x0>;
+			xlnx,sco = <0x0>;
+			xlnx,trace = <0x0>;
+			xlnx,unaligned-exceptions = <0x1>;
+			xlnx,use-barrel = <0x1>;
+			xlnx,use-branch-target-cache = <0x0>;
+			xlnx,use-config-reset = <0x0>;
+			xlnx,use-dcache = <0x1>;
+			xlnx,use-div = <0x1>;
+			xlnx,use-ext-brk = <0x0>;
+			xlnx,use-ext-nm-brk = <0x0>;
+			xlnx,use-extended-fsl-instr = <0x0>;
+			xlnx,use-fpu = <0x2>;
+			xlnx,use-hw-mul = <0x2>;
+			xlnx,use-icache = <0x1>;
+			xlnx,use-interrupt = <0x1>;
+			xlnx,use-mmu = <0x3>;
+			xlnx,use-msr-instr = <0x1>;
+			xlnx,use-pcmp-instr = <0x1>;
+			xlnx,use-reorder-instr = <0x1>;
+			xlnx,use-stack-protection = <0x0>;
+		} ;
+	} ;
+
+	clocks {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		clk_cpu: clk_cpu@0 {
+			#clock-cells = <0>;
+			clock-frequency = <100000000>;
+			clock-output-names = "clk_cpu";
+			compatible = "fixed-clock";
+			reg = <0>;
+		};
+		clk_bus: clk_bus@1 {
+			#clock-cells = <0>;
+			clock-frequency = <100000000>;
+			clock-output-names = "clk_bus_0";
+			compatible = "fixed-clock";
+			reg = <1>;
+		};
+	};
+
+	microblaze_1_axi_periph_xbar: axi {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "xlnx,axi-crossbar-2.0", "simple-bus";
+		ranges ;
+		axi_dma_1: axi-dma@41e00000 {
+			axistream-connected = <&axi_ethernet_1_axi_ethernet_buffer>;
+			axistream-control-connected = <&axi_ethernet_1_axi_ethernet_buffer>;
+			compatible = "xlnx,axi-dma-7.0", "xlnx,axi-dma-1.00.a";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 1 2 0 2 >;
+			reg = < 0x41e00000 0x10000 >;
+			xlnx,c-dlytmr-resolution = <0x4e2>;
+			xlnx,c-enable-multi-channel = <0x0>;
+			xlnx,c-include-mm2s = <0x1>;
+			xlnx,c-include-mm2s-dre = <0x1>;
+			xlnx,c-include-mm2s-sf = <0x1>;
+			xlnx,c-include-s2mm = <0x1>;
+			xlnx,c-include-s2mm-dre = <0x1>;
+			xlnx,c-include-s2mm-sf = <0x1>;
+			xlnx,c-include-sg = <0x1>;
+			xlnx,c-m-axi-mm2s-data-width = <0x20>;
+			xlnx,c-m-axi-s2mm-data-width = <0x20>;
+			xlnx,c-m-axis-mm2s-tdata-width = <0x20>;
+			xlnx,c-mm2s-burst-size = <0x10>;
+			xlnx,c-num-mm2s-channels = <0x1>;
+			xlnx,c-num-s2mm-channels = <0x1>;
+			xlnx,c-prmry-is-aclk-async = <0x0>;
+			xlnx,c-s-axis-s2mm-tdata-width = <0x20>;
+			xlnx,c-s2mm-burst-size = <0x10>;
+			xlnx,c-sg-include-desc-queue = <0x1>;
+			xlnx,c-sg-include-stscntrl-strm = <0x1>;
+			xlnx,c-sg-length-width = <0x10>;
+			xlnx,c-sg-use-stsapp-length = <0x1>;
+			xlnx,component-name = "kc705_smp_4_axi_dma_1_0";
+			xlnx,dlytmr-resolution = <0x4e2>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,enable-multi-channel = <0x0>;
+			xlnx,family = "kintex7";
+			xlnx,include-mm2s = <0x1>;
+			xlnx,include-mm2s-dre = <0x1>;
+			xlnx,include-mm2s-sf = <0x1>;
+			xlnx,include-s2mm = <0x1>;
+			xlnx,include-s2mm-dre = <0x1>;
+			xlnx,include-s2mm-sf = <0x1>;
+			xlnx,include-sg = <0x1>;
+			xlnx,mm2s-burst-size = <0x10>;
+			xlnx,num-mm2s-channels = <0x1>;
+			xlnx,num-s2mm-channels = <0x1>;
+			xlnx,prmry-is-aclk-async = <0x0>;
+			xlnx,s2mm-burst-size = <0x10>;
+			xlnx,sg-include-desc-queue = <0x1>;
+			xlnx,sg-include-stscntrl-strm = <0x1>;
+			xlnx,sg-length-width = <0x10>;
+			xlnx,sg-use-stsapp-length = <0x1>;
+		} ;
+		axi_ethernet_1_axi_ethernet_buffer: axi-ethernet@44a00000 {
+			axistream-connected = <&axi_dma_1>;
+			axistream-control-connected = <&axi_dma_1>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,axi-ethernet-buffer-2.0", "xlnx,axi-ethernet-3.01.a", "xlnx,axi-ethernet-1.00.a";
+			device_type = "network";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 4 2 >;
+			local-mac-address = [ 00 0a 35 00 d9 4d ];
+			phy-handle = <&phy0>;
+			reg = < 0x44a00000 0x40000 >;
+			xlnx,avb = <0x0>;
+			xlnx,halfdup = <0x0>;
+			xlnx,include-io = "1";
+			xlnx,mcast-extend = <0x0>;
+			xlnx,phy-type = <0x1>;
+			xlnx,phyaddr = <0x1>;
+			xlnx,rxcsum = <0x0>;
+			xlnx,rxmem = <0x1000>;
+			xlnx,rxvlan-strp = <0x0>;
+			xlnx,rxvlan-tag = <0x0>;
+			xlnx,rxvlan-tran = <0x0>;
+			xlnx,stats = <0x0>;
+			xlnx,txcsum = <0x0>;
+			xlnx,txmem = <0x1000>;
+			xlnx,txvlan-strp = <0x0>;
+			xlnx,txvlan-tag = <0x0>;
+			xlnx,txvlan-tran = <0x0>;
+			xlnx,type = <0x1>;
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy0: phy@7 {
+					compatible = "marvell,88e1111";
+					device_type = "ethernet-phy";
+					reg = <7>;
+				} ;
+			} ;
+		} ;
+		axi_gpio_1: gpio@40000000 {
+			#gpio-cells = <2>;
+			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
+			gpio-controller ;
+			reg = < 0x40000000 0x10000 >;
+			xlnx,all-inputs = <0x1>;
+			xlnx,all-inputs-2 = <0x0>;
+			xlnx,all-outputs = <0x0>;
+			xlnx,all-outputs-2 = <0x0>;
+			xlnx,component-name = "kc705_smp_4_axi_gpio_1_0";
+			xlnx,dout-default = <0x0>;
+			xlnx,dout-default-2 = <0x0>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,family = "kintex7";
+			xlnx,gpio-board-interface = "dip_switches_4bits";
+			xlnx,gpio-width = <0x4>;
+			xlnx,gpio2-board-interface = "Custom";
+			xlnx,gpio2-width = <0x20>;
+			xlnx,interrupt-present = <0x0>;
+			xlnx,is-dual = <0x0>;
+			xlnx,tri-default = <0xffffffff>;
+			xlnx,tri-default-2 = <0xffffffff>;
+			xlnx,use-board-flow = <0x1>;
+		} ;
+		axi_gpio_2: gpio@40010000 {
+			#gpio-cells = <2>;
+			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
+			gpio-controller ;
+			reg = < 0x40010000 0x10000 >;
+			xlnx,all-inputs = <0x0>;
+			xlnx,all-inputs-2 = <0x0>;
+			xlnx,all-outputs = <0x1>;
+			xlnx,all-outputs-2 = <0x0>;
+			xlnx,component-name = "kc705_smp_4_axi_gpio_2_1";
+			xlnx,dout-default = <0x0>;
+			xlnx,dout-default-2 = <0x0>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,family = "kintex7";
+			xlnx,gpio-board-interface = "led_8bits";
+			xlnx,gpio-width = <0x8>;
+			xlnx,gpio2-board-interface = "Custom";
+			xlnx,gpio2-width = <0x20>;
+			xlnx,interrupt-present = <0x0>;
+			xlnx,is-dual = <0x0>;
+			xlnx,tri-default = <0xffffffff>;
+			xlnx,tri-default-2 = <0xffffffff>;
+			xlnx,use-board-flow = <0x1>;
+		} ;
+		axi_gpio_3: gpio@40020000 {
+			#gpio-cells = <2>;
+			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
+			gpio-controller ;
+			reg = < 0x40020000 0x10000 >;
+			xlnx,all-inputs = <0x1>;
+			xlnx,all-inputs-2 = <0x0>;
+			xlnx,all-outputs = <0x0>;
+			xlnx,all-outputs-2 = <0x0>;
+			xlnx,component-name = "kc705_smp_4_axi_gpio_3_2";
+			xlnx,dout-default = <0x0>;
+			xlnx,dout-default-2 = <0x0>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,family = "kintex7";
+			xlnx,gpio-board-interface = "push_buttons_5bits";
+			xlnx,gpio-width = <0x5>;
+			xlnx,gpio2-board-interface = "Custom";
+			xlnx,gpio2-width = <0x20>;
+			xlnx,interrupt-present = <0x0>;
+			xlnx,is-dual = <0x0>;
+			xlnx,tri-default = <0xffffffff>;
+			xlnx,tri-default-2 = <0xffffffff>;
+			xlnx,use-board-flow = <0x1>;
+		} ;
+		axi_timer_1: system-timer@43c00000 {
+			clocks = <&clk_bus>;
+			cpu-id = <0xf>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,axi-timer-2.0", "xlnx,xps-timer-1.00.a";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 2 2 >;
+			reg = < 0x43c00000 0x1000 >;
+			xlnx,component-name = "kc705_smp_4_axi_timer_1_0";
+			xlnx,count-width = <0x20>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,enable-timer2 = <0x1>;
+			xlnx,family = "kintex7";
+			xlnx,gen0-assert = <0x1>;
+			xlnx,gen1-assert = <0x1>;
+			xlnx,mode-64bit = <0x0>;
+			xlnx,one-timer-only = <0x0>;
+			xlnx,trig0-assert = <0x1>;
+			xlnx,trig1-assert = <0x1>;
+		} ;
+		axi_timer_private_1: timer@43c01000 {
+			clocks = <&clk_bus>;
+			cpu-id = <0>;
+			clock-frequency = <100000000>;
+			compatible = "xlnx,axi-timer-2.0", "xlnx,xps-timer-1.00.a";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 5 2 >;
+			reg = < 0x43c01000 0x1000 >;
+			xlnx,component-name = "kc705_smp_4_axi_timer_private_1_1";
+			xlnx,count-width = <0x20>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,enable-timer2 = <0x0>;
+			xlnx,family = "kintex7";
+			xlnx,gen0-assert = <0x1>;
+			xlnx,gen1-assert = <0x1>;
+			xlnx,mode-64bit = <0x0>;
+			xlnx,one-timer-only = <0x1>;
+			xlnx,trig0-assert = <0x1>;
+			xlnx,trig1-assert = <0x1>;
+		} ;
+		axi_timer_private_2: timer@43c02000 {
+			clocks = <&clk_bus>;
+			clock-frequency = <100000000>;
+			cpu-id = <1>;
+			compatible = "xlnx,axi-timer-2.0", "xlnx,xps-timer-1.00.a";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 6 2 >;
+			reg = < 0x43c02000 0x1000 >;
+			xlnx,component-name = "kc705_smp_4_axi_timer_private_2_2";
+			xlnx,count-width = <0x20>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,enable-timer2 = <0x0>;
+			xlnx,family = "kintex7";
+			xlnx,gen0-assert = <0x1>;
+			xlnx,gen1-assert = <0x1>;
+			xlnx,mode-64bit = <0x0>;
+			xlnx,one-timer-only = <0x1>;
+			xlnx,trig0-assert = <0x1>;
+			xlnx,trig1-assert = <0x1>;
+		} ;
+		axi_timer_private_3: timer@43c03000 {
+			clocks = <&clk_bus>;
+			clock-frequency = <100000000>;
+			cpu-id = <2>;
+			compatible = "xlnx,axi-timer-2.0", "xlnx,xps-timer-1.00.a";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 7 2 >;
+			reg = < 0x43c03000 0x1000 >;
+			xlnx,component-name = "kc705_smp_4_axi_timer_private_3_3";
+			xlnx,count-width = <0x20>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,enable-timer2 = <0x0>;
+			xlnx,family = "kintex7";
+			xlnx,gen0-assert = <0x1>;
+			xlnx,gen1-assert = <0x1>;
+			xlnx,mode-64bit = <0x0>;
+			xlnx,one-timer-only = <0x1>;
+			xlnx,trig0-assert = <0x1>;
+			xlnx,trig1-assert = <0x1>;
+		} ;
+		axi_timer_private_4: timer@43c04000 {
+			clocks = <&clk_bus>;
+			clock-frequency = <100000000>;
+			cpu-id = <3>;
+			compatible = "xlnx,axi-timer-2.0", "xlnx,xps-timer-1.00.a";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 8 2 >;
+			reg = < 0x43c04000 0x1000 >;
+			xlnx,component-name = "kc705_smp_4_axi_timer_private_4_4";
+			xlnx,count-width = <0x20>;
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,enable-timer2 = <0x0>;
+			xlnx,family = "kintex7";
+			xlnx,gen0-assert = <0x1>;
+			xlnx,gen1-assert = <0x1>;
+			xlnx,mode-64bit = <0x0>;
+			xlnx,one-timer-only = <0x1>;
+			xlnx,trig0-assert = <0x1>;
+			xlnx,trig1-assert = <0x1>;
+		} ;
+		axi_uart16550_1: serial@40400000 {
+			clock-frequency = <100000000>;
+			compatible = "xlnx,axi-uart16550-2.0", "xlnx,xps-uart16550-2.00.a", "ns16550a";
+			current-speed = <115200>;
+			device_type = "serial";
+			interrupt-parent = <&microblaze_1_axi_intc>;
+			interrupts = < 3 2 >;
+			reg = < 0x40400000 0x2000 >;
+			reg-offset = <0x1000>;
+			reg-shift = <2>;
+			xlnx,base-user = <0x1>;
+			xlnx,component-name = "kc705_smp_4_axi_uart16550_1_0";
+			xlnx,edk-iptype = "PERIPHERAL";
+			xlnx,external-xin-clk-hz = <0x17d7840>;
+			xlnx,external-xin-clk-hz-d = <0x19>;
+			xlnx,family = "kintex7";
+			xlnx,has-external-rclk = <0x0>;
+			xlnx,has-external-xin = <0x0>;
+			xlnx,is-a-16550 = <0x1>;
+			xlnx,s-axi-aclk-freq-hz-d = <0x64>;
+			xlnx,uart-board-interface = "Custom";
+			xlnx,use-board-flow = <0x0>;
+			xlnx,use-modem-ports = <0x1>;
+			xlnx,use-user-ports = <0x1>;
+		} ;
+		microblaze_1_axi_intc: interrupt-controller@41800000 {
+			#interrupt-cells = <0x2>;
+			compatible = "xlnx,axi-intc-3.1", "xlnx,xps-intc-1.00.a";
+			interrupt-controller ;
+			cpu-id = <0>;
+			reg = < 0x41800000 0x1000 >;
+			xlnx,kind-of-intr = <0x0>;
+			xlnx,num-intr-inputs = <0x9>;
+			xlnx,num-sw-intr = <4>;
+		} ;
+		microblaze_2_axi_intc: interrupt-controller@41801000 {
+			#interrupt-cells = <0x2>;
+			compatible = "xlnx,axi-intc-3.1", "xlnx,xps-intc-1.00.a";
+			interrupt-controller ;
+			cpu-id = <1>;
+			reg = < 0x41801000 0x1000 >;
+			xlnx,kind-of-intr = <0x0>;
+			xlnx,num-intr-inputs = <0x9>;
+			xlnx,num-sw-intr = <4>;
+		} ;
+		microblaze_3_axi_intc: interrupt-controller@41802000 {
+			#interrupt-cells = <0x2>;
+			compatible = "xlnx,axi-intc-3.1", "xlnx,xps-intc-1.00.a";
+			interrupt-controller ;
+			cpu-id = <2>;
+			reg = < 0x41802000 0x1000 >;
+			xlnx,kind-of-intr = <0x0>;
+			xlnx,num-intr-inputs = <0x9>;
+			xlnx,num-sw-intr = <4>;
+		} ;
+		microblaze_4_axi_intc: interrupt-controller@41803000 {
+			#interrupt-cells = <0x2>;
+			compatible = "xlnx,axi-intc-3.1", "xlnx,xps-intc-1.00.a";
+			interrupt-controller ;
+			cpu-id = <3>;
+			reg = < 0x41803000 0x1000 >;
+			xlnx,kind-of-intr = <0x0>;
+			xlnx,num-intr-inputs = <0x9>;
+			xlnx,num-sw-intr = <4>;
+		} ;
+	} ;
+} ;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/configs/mmu_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/configs/mmu_defconfig
@@ -22,7 +22,6 @@
 CONFIG_PCI_XILINX=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 # CONFIG_EFI_PARTITION is not set
 CONFIG_CMA=y
@@ -45,6 +44,7 @@
 CONFIG_XILINX_EMACLITE=y
 CONFIG_XILINX_AXI_EMAC=y
 CONFIG_XILINX_LL_TEMAC=y
+CONFIG_MARVELL_PHY=y
 # CONFIG_INPUT is not set
 # CONFIG_SERIO is not set
 # CONFIG_VT is not set
@@ -80,7 +80,6 @@
 CONFIG_ROMFS_FS=y
 CONFIG_NFS_FS=y
 CONFIG_CIFS=y
-CONFIG_CIFS_STATS2=y
 CONFIG_ENCRYPTED_KEYS=y
 CONFIG_DMA_CMA=y
 CONFIG_DEBUG_INFO=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/configs/smp_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/configs/smp_defconfig
@@ -0,0 +1,99 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_BASE_FULL is not set
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_SMP=y
+CONFIG_NR_CPUS=4
+CONFIG_KERNEL_BASE_ADDR=0x80000000
+CONFIG_XILINX_MICROBLAZE0_FAMILY="kintex7"
+CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR=1
+CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR=1
+CONFIG_XILINX_MICROBLAZE0_USE_BARREL=1
+CONFIG_XILINX_MICROBLAZE0_USE_DIV=1
+CONFIG_XILINX_MICROBLAZE0_USE_HW_MUL=2
+CONFIG_XILINX_MICROBLAZE0_USE_FPU=2
+CONFIG_XILINX_MICROBLAZE0_HW_VER="9.1"
+CONFIG_HZ_100=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon"
+CONFIG_PCI_XILINX=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_CMA=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_IPV6 is not set
+CONFIG_BRIDGE=m
+CONFIG_PCI=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_NETDEVICES=y
+CONFIG_XILINX_EMACLITE=y
+CONFIG_XILINX_AXI_EMAC=y
+CONFIG_XILINX_LL_TEMAC=y
+CONFIG_MARVELL_PHY=y
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_XILINX_HWICAP=y
+CONFIG_I2C=y
+CONFIG_I2C_XILINX=y
+CONFIG_SPI=y
+CONFIG_SPI_XILINX=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_XILINX_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_FB_XILINX=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_UIO=y
+CONFIG_UIO_PDRV_GENIRQ=y
+CONFIG_UIO_DMEM_GENIRQ=y
+CONFIG_EXT3_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_TMPFS=y
+CONFIG_CRAMFS=y
+CONFIG_ROMFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_CIFS=y
+CONFIG_ENCRYPTED_KEYS=y
+CONFIG_CRYPTO_DES=y
+CONFIG_DMA_CMA=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_KGDB=y
+CONFIG_KGDB_TESTS=y
+CONFIG_KGDB_KDB=y
+CONFIG_DEBUG_SLAB=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_DEBUG_SPINLOCK=y
+# CONFIG_RCU_TRACE is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/Kbuild
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/Kbuild
@@ -1,6 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
 generated-y += syscall_table.h
-generic-y += cmpxchg.h
 generic-y += extable.h
 generic-y += kvm_para.h
 generic-y += mcs_spinlock.h
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/atomic.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/atomic.h
@@ -0,0 +1,269 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013-2020 Xilinx, Inc.
+ */
+
+#ifndef _ASM_MICROBLAZE_ATOMIC_H
+#define _ASM_MICROBLAZE_ATOMIC_H
+
+#include <linux/types.h>
+#include <asm/cmpxchg.h>
+
+#define ATOMIC_INIT(i)	{ (i) }
+
+#define arch_atomic_read(v)	READ_ONCE((v)->counter)
+
+static inline void arch_atomic_set(atomic_t *v, int i)
+{
+	int result, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %2 to %0 */
+		"1:	lwx	%0, %2, r0;\n"
+		/* attempt store */
+		"	swx	%3, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		/* Outputs: result value */
+		: "=&r" (result), "=&r" (tmp)
+		/* Inputs: counter address */
+		: "r" (&v->counter), "r" (i)
+		: "cc", "memory"
+	);
+}
+#define arch_atomic_set	arch_atomic_set
+
+/* Atomically perform op with v->counter and i, return result */
+#define ATOMIC_OP_RETURN(op, asm)					\
+static inline int arch_atomic_##op##_return_relaxed(int i, atomic_t *v)	\
+{									\
+	int result, tmp;						\
+									\
+	__asm__ __volatile__ (						\
+		/* load conditional address in %2 to %0 */		\
+		"1:	lwx	%0, %2, r0;\n"				\
+		/* perform operation and save it to result */		\
+		#asm		" %0, %3, %0;\n"			\
+		/* attempt store */					\
+		"	swx	%0, %2, r0;\n"				\
+		/* checking msr carry flag */				\
+		"	addic	%1, r0, 0;\n"				\
+		/* store failed (MSR[C] set)? try again */		\
+		"	bnei	%1, 1b;\n"				\
+		/* Outputs: result value */				\
+		: "=&r" (result), "=&r" (tmp)				\
+		/* Inputs: counter address */				\
+		: "r"   (&v->counter), "r" (i)				\
+		: "cc", "memory"					\
+	);								\
+									\
+	return result;							\
+}									\
+									\
+static inline void arch_atomic_##op(int i, atomic_t *v)			\
+{									\
+	arch_atomic_##op##_return_relaxed(i, v);				\
+}
+
+/* Atomically perform op with v->counter and i, return orig v->counter */
+#define ATOMIC_FETCH_OP_RELAXED(op, asm)				\
+static inline int arch_atomic_fetch_##op##_relaxed(int i, atomic_t *v)	\
+{									\
+	int old, tmp;							\
+									\
+	__asm__ __volatile__ (						\
+		/* load conditional address in %2 to %0 */		\
+		"1:	lwx	%0, %2, r0;\n"				\
+		/* perform operation and save it to tmp */		\
+		#asm		" %1, %3, %0;\n"			\
+		/* attempt store */					\
+		"	swx	%1, %2, r0;\n"				\
+		/* checking msr carry flag */				\
+		"	addic	%1, r0, 0;\n"				\
+		/* store failed (MSR[C] set)? try again */		\
+		"	bnei	%1, 1b;\n"				\
+		/* Outputs: old value */				\
+		: "=&r" (old), "=&r" (tmp)				\
+		/* Inputs: counter address */				\
+		: "r"   (&v->counter), "r" (i)				\
+		: "cc", "memory"					\
+	);								\
+									\
+	return old;							\
+}
+
+#define ATOMIC_OPS(op, asm) \
+	ATOMIC_FETCH_OP_RELAXED(op, asm) \
+	ATOMIC_OP_RETURN(op, asm)
+
+ATOMIC_OPS(and, and)
+#define arch_atomic_and			arch_atomic_and
+#define arch_atomic_and_return_relaxed	arch_atomic_and_return_relaxed
+#define arch_atomic_fetch_and_relaxed	arch_atomic_fetch_and_relaxed
+
+ATOMIC_OPS(add, add)
+#define arch_atomic_add			arch_atomic_add
+#define arch_atomic_add_return_relaxed	arch_atomic_add_return_relaxed
+#define arch_atomic_fetch_add_relaxed	arch_atomic_fetch_add_relaxed
+
+ATOMIC_OPS(xor, xor)
+#define arch_atomic_xor			arch_atomic_xor
+#define arch_atomic_xor_return_relaxed	arch_atomic_xor_return_relaxed
+#define arch_atomic_fetch_xor_relaxed	arch_atomic_fetch_xor_relaxed
+
+ATOMIC_OPS(or, or)
+#define arch_atomic_or			arch_atomic_or
+#define arch_atomic_or_return_relaxed	arch_atomic_or_return_relaxed
+#define arch_atomic_fetch_or_relaxed	arch_atomic_fetch_or_relaxed
+
+ATOMIC_OPS(sub, rsub)
+#define arch_atomic_sub			arch_atomic_sub
+#define arch_atomic_sub_return_relaxed	arch_atomic_sub_return_relaxed
+#define arch_atomic_fetch_sub_relaxed	arch_atomic_fetch_sub_relaxed
+
+static inline int arch_atomic_inc_return_relaxed(atomic_t *v)
+{
+	int result, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %2 to %0 */
+		"1:	lwx	%0, %2, r0;\n"
+		/* increment counter by 1 */
+		"	addi	%0, %0, 1;\n"
+		/* attempt store */
+		"	swx	%0, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		/* Outputs: result value */
+		: "=&r" (result), "=&r" (tmp)
+		/* Inputs: counter address */
+		: "r"   (&v->counter)
+		: "cc", "memory"
+	);
+
+	return result;
+}
+#define arch_atomic_inc_return_relaxed	arch_atomic_inc_return_relaxed
+
+#define arch_atomic_inc_and_test(v)	(arch_atomic_inc_return(v) == 0)
+
+static inline int arch_atomic_dec_return(atomic_t *v)
+{
+	int result, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %2 to %0 */
+		"1:	lwx	%0, %2, r0;\n"
+		/* increment counter by -1 */
+		"	addi	%0, %0, -1;\n"
+		/* attempt store */
+		"	swx	%0, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		/* Outputs: result value */
+		: "=&r" (result), "=&r" (tmp)
+		/* Inputs: counter address */
+		: "r"   (&v->counter)
+		: "cc", "memory"
+	);
+
+	return result;
+}
+#define arch_atomic_dec_return	arch_atomic_dec_return
+
+static inline void arch_atomic_dec(atomic_t *v)
+{
+	arch_atomic_dec_return(v);
+}
+#define arch_atomic_dec	arch_atomic_dec
+
+#define arch_atomic_sub_and_test(a, v)	(arch_atomic_sub_return((a), (v)) == 0)
+#define arch_atomic_dec_and_test(v)	(arch_atomic_dec_return((v)) == 0)
+
+#define arch_atomic_cmpxchg(v, o, n)	(arch_cmpxchg(&((v)->counter), (o), (n)))
+#define arch_atomic_xchg(v, new)	(arch_xchg(&((v)->counter), new))
+
+/**
+ * atomic_add_unless - add unless the number is a given value
+ * @v: pointer of type atomic_t
+ * @a: the amount to add to v...
+ * @u: ...unless v is equal to u.
+ *
+ * Atomically adds @a to @v, so long as it was not @u.
+ * Returns the old value of @v.
+ */
+static inline int __atomic_add_unless(atomic_t *v, int a, int u)
+{
+	int result, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %2 to %0 */
+		"1: lwx	 %0, %2, r0;\n"
+		/* compare loaded value with old value*/
+		"   cmp   %1, %0, %3;\n"
+		/* equal to u, don't increment */
+		"   beqid %1, 2f;\n"
+		/* increment counter by i */
+		"   add   %1, %0, %4;\n"
+		/* attempt store of new value*/
+		"   swx   %1, %2, r0;\n"
+		/* checking msr carry flag */
+		"   addic %1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"   bnei  %1, 1b;\n"
+		"2:"
+		/* Outputs: result value */
+		: "=&r" (result), "=&r" (tmp)
+		/* Inputs: counter address, old, new */
+		: "r"   (&v->counter), "r" (u), "r" (a)
+		: "cc", "memory"
+	);
+
+	return result;
+}
+
+/*
+ * Atomically test *v and decrement if it is greater than 0.
+ * The function returns the old value of *v minus 1, even if
+ * the atomic variable, v, was not decremented.
+ */
+static inline int arch_atomic_dec_if_positive(atomic_t *v)
+{
+	int result, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %2 to %0 */
+		"1:	lwx	%0, %2, r0;\n"
+		/* decrement counter by 1*/
+		"	addi	%0, %0, -1;\n"
+		/* if < 0 abort (*v was <= 0)*/
+		"	blti	%0, 2f;\n"
+		/* attempt store of new value*/
+		"	swx	%0, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		"2: "
+		/* Outputs: result value */
+		: "=&r" (result), "=&r" (tmp)
+		/* Inputs: counter address */
+		: "r"   (&v->counter)
+		: "cc", "memory"
+	);
+
+	return result;
+}
+#define arch_atomic_dec_if_positive	arch_atomic_dec_if_positive
+
+#define arch_atomic_add_negative(i, v)	(arch_atomic_add_return(i, v) < 0)
+
+#include <asm-generic/atomic64.h>
+
+#endif /* _ASM_MICROBLAZE_ATOMIC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/bitops.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/bitops.h
@@ -0,0 +1,190 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Microblaze atomic bit operations.
+ *
+ * Copyright (C) 2013 - 2020 Xilinx, Inc.
+ *
+ * Merged version by David Gibson <david@gibson.dropbear.id.au>.
+ * Based on ppc64 versions by: Dave Engebretsen, Todd Inglett, Don
+ * Reed, Pat McCarthy, Peter Bergner, Anton Blanchard.  They
+ * originally took it from the ppc32 code.
+ *
+ * Within a word, bits are numbered LSB first.  Lot's of places make
+ * this assumption by directly testing bits with (val & (1<<nr)).
+ * This can cause confusion for large (> 1 word) bitmaps on a
+ * big-endian system because, unlike little endian, the number of each
+ * bit depends on the word size.
+ *
+ * The bitop functions are defined to work on unsigned longs, so for a
+ * ppc64 system the bits end up numbered:
+ *   |63..............0|127............64|191...........128|255...........196|
+ * and on ppc32:
+ *   |31.....0|63....31|95....64|127...96|159..128|191..160|223..192|255..224|
+ *
+ * There are a few little-endian macros used mostly for filesystem
+ * bitmaps, these work on similar bit arrays layouts, but
+ * byte-oriented:
+ *   |7...0|15...8|23...16|31...24|39...32|47...40|55...48|63...56|
+ *
+ * The main difference is that bit 3-5 (64b) or 3-4 (32b) in the bit
+ * number field needs to be reversed compared to the big-endian bit
+ * fields. This can be achieved by XOR with 0x38 (64b) or 0x18 (32b).
+ */
+
+#ifndef _ASM_MICROBLAZE_BITOPS_H
+#define _ASM_MICROBLAZE_BITOPS_H
+
+#ifndef _LINUX_BITOPS_H
+#error only <linux/bitops.h> can be included directly
+#endif
+
+#include <asm/types.h>
+#include <linux/compiler.h>
+#include <asm/asm-compat.h>
+#include <asm/barrier.h>
+#include <linux/stringify.h>
+
+/*
+ * clear_bit doesn't imply a memory barrier
+ */
+#define smp_mb__before_clear_bit()	smp_mb()
+#define smp_mb__after_clear_bit()	smp_mb()
+
+#define BITOP_MASK(nr)		(1UL << ((nr) % BITS_PER_LONG))
+#define BITOP_WORD(nr)		((nr) / BITS_PER_LONG)
+
+/* Macro for generating the ***_bits() functions */
+#define DEFINE_BITOP(fn, op)						\
+static inline void fn(unsigned long mask, volatile unsigned long *_p)	\
+{									\
+	unsigned long tmp;						\
+	unsigned long *p = (unsigned long *)_p;				\
+									\
+	__asm__ __volatile__ (						\
+		/* load conditional address in %2 to %0 */		\
+		"1:	lwx		%0, %3, r0;\n"			\
+		/* perform bit operation with mask */			\
+		stringify_in_c(op)"	%0, %0, %2;\n"			\
+		/* attempt store */					\
+		"	swx		%0, %3, r0;\n"			\
+		/* checking msr carry flag */				\
+		"	addic		%0, r0, 0;\n"			\
+		/* store failed (MSR[C] set)? try again */		\
+		"	bnei		%0, 1b;\n"			\
+		: "=&r" (tmp), "+m" (*p)  /* Outputs: tmp, p */		\
+		: "r" (mask), "r" (p)     /* Inputs: mask, p */		\
+		: "cc", "memory"					\
+	);								\
+}
+
+DEFINE_BITOP(set_bits, or)
+DEFINE_BITOP(clear_bits, andn)
+DEFINE_BITOP(clear_bits_unlock, andn)
+DEFINE_BITOP(change_bits, xor)
+
+static inline void set_bit(int nr, volatile unsigned long *addr)
+{
+	set_bits(BITOP_MASK(nr), addr + BITOP_WORD(nr));
+}
+
+static inline void clear_bit(int nr, volatile unsigned long *addr)
+{
+	clear_bits(BITOP_MASK(nr), addr + BITOP_WORD(nr));
+}
+
+static inline void clear_bit_unlock(int nr, volatile unsigned long *addr)
+{
+	clear_bits_unlock(BITOP_MASK(nr), addr + BITOP_WORD(nr));
+}
+
+static inline void change_bit(int nr, volatile unsigned long *addr)
+{
+	change_bits(BITOP_MASK(nr), addr + BITOP_WORD(nr));
+}
+
+/*
+ * Like DEFINE_BITOP(), with changes to the arguments to 'op' and the output
+ * operands.
+ */
+#define DEFINE_TESTOP(fn, op)						\
+static inline unsigned long fn(unsigned long mask,			\
+			       volatile unsigned long *_p)		\
+{									\
+	unsigned long old, tmp;						\
+	unsigned long *p = (unsigned long *)_p;				\
+									\
+	__asm__ __volatile__ (						\
+		/* load conditional address in %4 to %0 */		\
+		"1:	lwx		%0, %4, r0;\n"			\
+		/* perform bit operation with mask */			\
+		stringify_in_c(op)"	%1, %0, %3;\n"			\
+		/* attempt store */					\
+		"	swx		%1, %4, r0;\n"			\
+		/* checking msr carry flag */				\
+		"	addic		%1, r0, 0;\n"			\
+		/* store failed (MSR[C] set)? try again */		\
+		"	bnei		%1, 1b;\n"			\
+		/* Outputs: old, tmp, p */				\
+		: "=&r" (old), "=&r" (tmp), "+m" (*p)			\
+		 /* Inputs: mask, p */					\
+		: "r" (mask), "r" (p)					\
+		: "cc", "memory"					\
+	);								\
+	return (old & mask);						\
+}
+
+DEFINE_TESTOP(test_and_set_bits, or)
+DEFINE_TESTOP(test_and_set_bits_lock, or)
+DEFINE_TESTOP(test_and_clear_bits, andn)
+DEFINE_TESTOP(test_and_change_bits, xor)
+
+static inline int test_and_set_bit(unsigned long nr,
+				       volatile unsigned long *addr)
+{
+	return test_and_set_bits(BITOP_MASK(nr), addr + BITOP_WORD(nr)) != 0;
+}
+
+static inline int test_and_set_bit_lock(unsigned long nr,
+				       volatile unsigned long *addr)
+{
+	return test_and_set_bits_lock(BITOP_MASK(nr),
+				addr + BITOP_WORD(nr)) != 0;
+}
+
+static inline int test_and_clear_bit(unsigned long nr,
+					 volatile unsigned long *addr)
+{
+	return test_and_clear_bits(BITOP_MASK(nr), addr + BITOP_WORD(nr)) != 0;
+}
+
+static inline int test_and_change_bit(unsigned long nr,
+					  volatile unsigned long *addr)
+{
+	return test_and_change_bits(BITOP_MASK(nr), addr + BITOP_WORD(nr)) != 0;
+}
+
+#include <asm-generic/bitops/non-atomic.h>
+
+static inline void __clear_bit_unlock(int nr, volatile unsigned long *addr)
+{
+	__clear_bit(nr, addr);
+}
+
+#include <asm-generic/bitops/ffz.h>
+#include <asm-generic/bitops/__fls.h>
+#include <asm-generic/bitops/__ffs.h>
+#include <asm-generic/bitops/fls.h>
+#include <asm-generic/bitops/ffs.h>
+#include <asm-generic/bitops/hweight.h>
+#include <asm-generic/bitops/find.h>
+#include <asm-generic/bitops/fls64.h>
+
+/* Little-endian versions */
+#include <asm-generic/bitops/le.h>
+
+/* Bitmap functions for the ext2 filesystem */
+#include <asm-generic/bitops/ext2-atomic-setbit.h>
+
+#include <asm-generic/bitops/sched.h>
+
+#endif /* _ASM_MICROBLAZE_BITOPS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/cmpxchg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/cmpxchg.h
@@ -0,0 +1,95 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MICROBLAZE_CMPXCHG_H
+#define _ASM_MICROBLAZE_CMPXCHG_H
+
+#ifndef CONFIG_SMP
+# include <asm-generic/cmpxchg.h>
+#else
+
+extern void __xchg_called_with_bad_pointer(void);
+
+static inline unsigned long __xchg_u32(volatile void *p, unsigned long val)
+{
+	unsigned long prev, temp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %3 to %0 */
+		"1:	lwx	%0, %3, r0;\n"
+		/* attempt store of new value */
+		"	swx	%4, %3, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		/* Outputs: result value */
+		: "=&r" (prev), "=&r" (temp), "+m" (*(volatile unsigned int *)p)
+		/* Inputs: counter address */
+		: "r"   (p), "r" (val)
+		: "cc", "memory"
+	);
+
+	return prev;
+}
+
+static inline unsigned long __xchg(unsigned long x, volatile void *ptr,
+								int size)
+{
+	if (size == 4)
+		return __xchg_u32(ptr, x);
+
+	__xchg_called_with_bad_pointer();
+	return x;
+}
+
+#define arch_xchg(ptr, x) ({							\
+	((__typeof__(*(ptr)))						\
+		__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))));	\
+})
+
+static inline unsigned long __cmpxchg_u32(volatile unsigned int *p,
+					  unsigned long old, unsigned long new)
+{
+	int result, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %3 to %0 */
+		"1:	lwx	%0, %3, r0;\n"
+		/* compare loaded value with old value */
+		"	cmp	%2, %0, %4;\n"
+		/* not equal to old value, write old value */
+		"	bnei	%2, 2f;\n"
+		/* attempt store of new value*/
+		"	swx	%5, %3, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%2, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%2, 1b;\n"
+		"2: "
+		/* Outputs : result value */
+		: "=&r" (result), "+m" (*p), "=&r" (tmp)
+		/* Inputs  : counter address, old, new */
+		: "r"   (p), "r" (old), "r" (new), "r" (&tmp)
+		: "cc", "memory"
+	);
+
+	return result;
+}
+
+static inline unsigned long __cmpxchg(volatile void *ptr, unsigned long old,
+				      unsigned long new, unsigned int size)
+{
+	if (size == 4)
+		return __cmpxchg_u32(ptr, old, new);
+
+	__xchg_called_with_bad_pointer();
+	return old;
+}
+
+#define arch_cmpxchg(ptr, o, n) ({						\
+	((__typeof__(*(ptr)))__cmpxchg((ptr), (unsigned long)(o),	\
+			(unsigned long)(n), sizeof(*(ptr))));		\
+})
+
+#endif
+
+#endif /* _ASM_MICROBLAZE_CMPXCHG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/cpuinfo.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/cpuinfo.h
@@ -84,7 +84,7 @@
 	u32 pvr_user2;
 };
 
-extern struct cpuinfo cpuinfo;
+DECLARE_PER_CPU(struct cpuinfo, cpu_info);
 
 /* fwd declarations of the various CPUinfo populators */
 void setup_cpuinfo(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/entry.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/entry.h
@@ -10,7 +10,6 @@
 #ifndef _ASM_MICROBLAZE_ENTRY_H
 #define _ASM_MICROBLAZE_ENTRY_H
 
-#include <asm/percpu.h>
 #include <asm/ptrace.h>
 #include <linux/linkage.h>
 
@@ -21,12 +20,23 @@
 
 #define PER_CPU(var) var
 
+#ifdef CONFIG_SMP
+/* Addresses in BRAM */
+#define CURRENT_SAVE_ADDR	0x50
+#define ENTRY_SP_ADDR		0x54
+#define PT_POOL_SPACE_ADDR	0x100
+#endif /* CONFIG_SMP */
+
 # ifndef __ASSEMBLY__
+#include <asm/percpu.h>
+
+#ifndef CONFIG_SMP
 DECLARE_PER_CPU(unsigned int, KSP); /* Saved kernel stack pointer */
 DECLARE_PER_CPU(unsigned int, KM); /* Kernel/user mode */
 DECLARE_PER_CPU(unsigned int, ENTRY_SP); /* Saved SP on kernel entry */
 DECLARE_PER_CPU(unsigned int, R11_SAVE); /* Temp variable for entry */
 DECLARE_PER_CPU(unsigned int, CURRENT_SAVE); /* Saved current pointer */
+#endif /* CONFIG_SMP */
 
 extern asmlinkage void do_notify_resume(struct pt_regs *regs, int in_syscall);
 # endif /* __ASSEMBLY__ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/hardirq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/hardirq.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2020 Xilinx, Inc.
+ * Copyright (C) 2012 ARM Ltd.
+ */
+#ifndef _ASM_MICROBLAZE_HARDIRQ_H
+#define _ASM_MICROBLAZE_HARDIRQ_H
+
+# ifndef CONFIG_SMP
+#include <asm-generic/hardirq.h>
+# else
+#include <linux/cache.h>
+#include <linux/percpu.h>
+#include <linux/threads.h>
+#include <asm/irq.h>
+#include <linux/irq.h>
+
+typedef struct {
+	unsigned int __softirq_pending;
+	unsigned int ipi_irqs[MICROBLAZE_NUM_IPIS];
+} ____cacheline_aligned irq_cpustat_t;
+
+#define __ARCH_IRQ_STAT
+DECLARE_PER_CPU_SHARED_ALIGNED(irq_cpustat_t, irq_stat);
+
+#define local_softirq_pending_ref	irq_stat.__softirq_pending
+
+#define __inc_irq_stat(cpu, member)	this_cpu_inc(irq_stat.member)
+#define __get_irq_stat(cpu, member)	this_cpu_read(irq_stat.member)
+
+u64 smp_irq_stat_cpu(unsigned int cpu);
+#define arch_irq_stat_cpu	smp_irq_stat_cpu
+
+extern unsigned long irq_err_count;
+
+static inline void ack_bad_irq(unsigned int irq)
+{
+	irq_err_count++;
+}
+# endif /* CONFIG_MMU */
+
+#endif /* _ASM_MICROBLAZE_HARDIRQ_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/irq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/irq.h
@@ -11,7 +11,4 @@
 struct pt_regs;
 extern void do_IRQ(struct pt_regs *regs);
 
-/* should be defined in each interrupt controller driver */
-extern unsigned int xintc_get_irq(void);
-
 #endif /* _ASM_MICROBLAZE_IRQ_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/mmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/mmu.h
@@ -12,7 +12,10 @@
 #   ifndef __ASSEMBLY__
 
 /* Default "unsigned long" context */
-typedef unsigned long mm_context_t;
+typedef struct {
+	unsigned int	id;
+	unsigned int	active;
+} mm_context_t;
 
 /* Hardware Page Table Entry */
 typedef struct _PTE {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/mmu_context_mm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/mmu_context_mm.h
@@ -1,5 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
+ * Copyright (C) 2013-2020 Xilinx, Inc
  * Copyright (C) 2008-2009 Michal Simek <monstr@monstr.eu>
  * Copyright (C) 2008-2009 PetaLogix
  * Copyright (C) 2006 Atmark Techno, Inc.
@@ -13,10 +14,13 @@
 #include <linux/sched.h>
 
 #include <asm/bitops.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
 #include <asm/mmu.h>
 #include <asm-generic/mm_hooks.h>
 
-# ifdef __KERNEL__
 /*
  * This function defines the mapping from contexts to VSIDs (virtual
  * segment IDs).  We use a skew on both the context and the high 4 bits
@@ -39,7 +43,7 @@
 
 /*
  * Set the current MMU context.
- * This is done byloading up the segment registers for the user part of the
+ * This is done by loading up the segment registers for the user part of the
  * address space.
  *
  * Since the PGD is immediately available, it is much faster to simply
@@ -47,94 +51,63 @@
  * can be used for debugging on all processors (if you happen to have
  * an Abatron).
  */
-extern void set_context(mm_context_t context, pgd_t *pgd);
-
-/*
- * Bitmap of contexts in use.
- * The size of this bitmap is LAST_CONTEXT + 1 bits.
- */
-extern unsigned long context_map[];
-
-/*
- * This caches the next context number that we expect to be free.
- * Its use is an optimization only, we can't rely on this context
- * number to be free, but it usually will be.
- */
-extern mm_context_t next_mmu_context;
+extern void set_context(unsigned long id, pgd_t *pgd);
 
 /*
  * Since we don't have sufficient contexts to give one to every task
  * that could be in the system, we need to be able to steal contexts.
- * These variables support that.
  */
-extern atomic_t nr_free_contexts;
-extern struct mm_struct *context_mm[LAST_CONTEXT+1];
 extern void steal_context(void);
 
 /*
- * Get a new mmu context for the address space described by `mm'.
- */
-static inline void get_mmu_context(struct mm_struct *mm)
-{
-	mm_context_t ctx;
-
-	if (mm->context != NO_CONTEXT)
-		return;
-	while (atomic_dec_if_positive(&nr_free_contexts) < 0)
-		steal_context();
-	ctx = next_mmu_context;
-	while (test_and_set_bit(ctx, context_map)) {
-		ctx = find_next_zero_bit(context_map, LAST_CONTEXT+1, ctx);
-		if (ctx > LAST_CONTEXT)
-			ctx = 0;
-	}
-	next_mmu_context = (ctx + 1) & LAST_CONTEXT;
-	mm->context = ctx;
-	context_mm[ctx] = mm;
-}
-
-/*
  * Set up the context for a new address space.
  */
-# define init_new_context(tsk, mm)	(((mm)->context = NO_CONTEXT), 0)
+extern int init_new_context(struct task_struct *tsk, struct mm_struct *mm);
+#define init_new_context init_new_context
 
 /*
  * We're finished using the context for an address space.
  */
+extern void destroy_context(struct mm_struct *mm);
+
 #define destroy_context destroy_context
-static inline void destroy_context(struct mm_struct *mm)
-{
-	if (mm->context != NO_CONTEXT) {
-		clear_bit(mm->context, context_map);
-		mm->context = NO_CONTEXT;
-		atomic_inc(&nr_free_contexts);
-	}
-}
+/*
+ * Switch context
+ */
+extern void switch_mmu_context(struct mm_struct *prev, struct mm_struct *next);
 
 static inline void switch_mm(struct mm_struct *prev, struct mm_struct *next,
 			     struct task_struct *tsk)
 {
+	/* Mark this context has been used on the new CPU */
+	cpumask_set_cpu(smp_processor_id(), mm_cpumask(next));
 	tsk->thread.pgdir = next->pgd;
-	get_mmu_context(next);
-	set_context(next->context, next->pgd);
+
+	/* Nothing else to do if we aren't actually switching */
+	if (prev == next)
+		return;
+
+	/* Out of line for now */
+	switch_mmu_context(prev, next);
 }
 
 /*
  * After we have set current->mm to a new value, this activates
  * the context for the new mm so we see the new mappings.
  */
-#define activate_mm activate_mm
 static inline void activate_mm(struct mm_struct *active_mm,
 			struct mm_struct *mm)
 {
-	current->thread.pgdir = mm->pgd;
-	get_mmu_context(mm);
-	set_context(mm->context, mm->pgd);
+	unsigned long flags;
+
+	local_irq_save(flags);
+	switch_mm(active_mm, mm, current);
+	local_irq_restore(flags);
 }
+#define activate_mm	activate_mm
 
 extern void mmu_context_init(void);
 
 #include <asm-generic/mmu_context.h>
 
-# endif /* __KERNEL__ */
 #endif /* _ASM_MICROBLAZE_MMU_CONTEXT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/pgtable.h
@@ -324,20 +324,19 @@
 static inline unsigned long pte_update(pte_t *p, unsigned long clr,
 				unsigned long set)
 {
-	unsigned long flags, old, tmp;
+	unsigned long old, tmp;
 
-	raw_local_irq_save(flags);
-
-	__asm__ __volatile__(	"lw	%0, %2, r0	\n"
-				"andn	%1, %0, %3	\n"
-				"or	%1, %1, %4	\n"
-				"sw	%1, %2, r0	\n"
+	__asm__ __volatile__(
+			"1:	lwx	%0, %2, r0;\n"
+			"	andn	%1, %0, %3;\n"
+			"	or	%1, %1, %4;\n"
+			"	swx	%1, %2, r0;\n"
+			"	addic	%1, r0, 0;\n"
+			"	bnei	%1, 1b;\n"
 			: "=&r" (old), "=&r" (tmp)
 			: "r" ((unsigned long)(p + 1) - 4), "r" (clr), "r" (set)
 			: "cc");
 
-	raw_local_irq_restore(flags);
-
 	return old;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/sections.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/sections.h
@@ -14,6 +14,9 @@
 extern char _ssbss[], _esbss[];
 extern unsigned long __ivt_start[], __ivt_end[];
 
+extern char __initramfs_end[];
+extern char _end_tlb_mapping[];
+
 extern u32 _fdt_start[], _fdt_end[];
 
 # endif /* !__ASSEMBLY__ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/smp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/smp.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * smp.h: MicroBlaze-specific SMP code
+ *
+ * Original was a copy of PowerPC smp.h, which was a copy of
+ * sparc smp.h.  Now heavily modified for PPC.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@caip.rutgers.edu)
+ * Copyright (C) 1996-2001 Cort Dougan <cort@fsmlabs.com>
+ * Copyright (C) 2013-2020 Xilinx, Inc.
+ */
+
+#ifndef _ASM_MICROBLAZE_SMP_H
+#define _ASM_MICROBLAZE_SMP_H
+
+#include <linux/threads.h>
+#include <linux/cpumask.h>
+#include <linux/kernel.h>
+
+#include <asm/percpu.h>
+
+void handle_IPI(int ipinr, struct pt_regs *regs);
+
+void set_smp_cross_call(void (*)(unsigned int, unsigned int));
+
+void smp_send_debugger_break(void);
+
+#define raw_smp_processor_id()		(current_thread_info()->cpu)
+
+enum microblaze_msg {
+	MICROBLAZE_MSG_RESCHEDULE = 0,
+	MICROBLAZE_MSG_CALL_FUNCTION,
+	MICROBLAZE_MSG_CALL_FUNCTION_SINGLE,
+	MICROBLAZE_MSG_DEBUGGER_BREAK,
+	MICROBLAZE_NUM_IPIS
+};
+
+void start_secondary(void);
+extern struct thread_info *secondary_ti;
+void secondary_machine_init(void);
+
+void arch_send_call_function_single_ipi(int cpu);
+void arch_send_call_function_ipi_mask(const struct cpumask *mask);
+
+#endif /* _ASM_MICROBLAZE_SMP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/spinlock.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/spinlock.h
@@ -0,0 +1,240 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013-2020 Xilinx, Inc.
+ */
+
+#ifndef _ASM_MICROBLAZE_SPINLOCK_H
+#define _ASM_MICROBLAZE_SPINLOCK_H
+
+/*
+ * Unlocked value: 0
+ * Locked value: 1
+ */
+#define arch_spin_is_locked(x)	(READ_ONCE((x)->lock) != 0)
+
+static inline void arch_spin_lock(arch_spinlock_t *lock)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to %0 */
+		"1:	lwx	 %0, %1, r0;\n"
+		/* not zero? try again */
+		"	bnei	%0, 1b;\n"
+		/* increment lock by 1 */
+		"	addi	%0, r0, 1;\n"
+		/* attempt store */
+		"	swx	%0, %1, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%0, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%0, 1b;\n"
+		/* Outputs: temp variable for load result */
+		: "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&lock->lock)
+		: "cc", "memory"
+	);
+}
+
+static inline int arch_spin_trylock(arch_spinlock_t *lock)
+{
+	unsigned long prev, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %2 to %0 */
+		"1:	lwx	 %0, %2, r0;\n"
+		/* not zero? clear reservation */
+		"	bneid	%0, 2f;\n"
+		/* increment lock by one if lwx was sucessful */
+		"	addi	%1, r0, 1;\n"
+		/* attempt store */
+		"	swx	%1, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		"2:"
+		/* Outputs: temp variable for load result */
+		: "=&r" (prev), "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&lock->lock)
+		: "cc", "memory"
+	);
+
+	return (prev == 0);
+}
+
+static inline void arch_spin_unlock(arch_spinlock_t *lock)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to %0 */
+		"1:	lwx	%0, %1, r0;\n"
+		/* clear */
+		"	swx	r0, %1, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%0, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%0, 1b;\n"
+		/* Outputs: temp variable for load result */
+		: "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&lock->lock)
+		: "cc", "memory"
+	);
+}
+
+/* RWLOCKS */
+static inline void arch_write_lock(arch_rwlock_t *rw)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to %0 */
+		"1:	lwx	 %0, %1, r0;\n"
+		/* not zero? try again */
+		"	bneid	%0, 1b;\n"
+		/* set tmp to -1 */
+		"	addi	%0, r0, -1;\n"
+		/* attempt store */
+		"	swx	%0, %1, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%0, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%0, 1b;\n"
+		/* Outputs: temp variable for load result */
+		: "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&rw->lock)
+		: "cc", "memory"
+	);
+}
+
+static inline int arch_write_trylock(arch_rwlock_t *rw)
+{
+	unsigned long prev, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to tmp */
+		"1:	lwx	%0, %2, r0;\n"
+		/* not zero? abort */
+		"	bneid	%0, 2f;\n"
+		/* set tmp to -1 */
+		"	addi	%1, r0, -1;\n"
+		/* attempt store */
+		"	swx	%1, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		"2:"
+		/* Outputs: temp variable for load result */
+		: "=&r" (prev), "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&rw->lock)
+		: "cc", "memory"
+	);
+	/* prev value should be zero and MSR should be clear */
+	return (prev == 0);
+}
+
+static inline void arch_write_unlock(arch_rwlock_t *rw)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to %0 */
+		"1:	lwx	%0, %1, r0;\n"
+		/* clear */
+		"	swx	r0, %1, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%0, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%0, 1b;\n"
+		/* Outputs: temp variable for load result */
+		: "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&rw->lock)
+		: "cc", "memory"
+	);
+}
+
+/* Read locks */
+static inline void arch_read_lock(arch_rwlock_t *rw)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to %0 */
+		"1:	lwx	%0, %1, r0;\n"
+		/* < 0 (WRITE LOCK active) try again */
+		"	bltid	%0, 1b;\n"
+		/* increment lock by 1 if lwx was sucessful */
+		"	addi	%0, %0, 1;\n"
+		/* attempt store */
+		"	swx	%0, %1, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%0, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%0, 1b;\n"
+		/* Outputs: temp variable for load result */
+		: "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&rw->lock)
+		: "cc", "memory"
+	);
+}
+
+static inline void arch_read_unlock(arch_rwlock_t *rw)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to tmp */
+		"1:	lwx	%0, %1, r0;\n"
+		/* tmp = tmp - 1 */
+		"	addi	%0, %0, -1;\n"
+		/* attempt store */
+		"	swx	%0, %1, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%0, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%0, 1b;\n"
+		/* Outputs: temp variable for load result */
+		: "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&rw->lock)
+		: "cc", "memory"
+	);
+}
+
+static inline int arch_read_trylock(arch_rwlock_t *rw)
+{
+	unsigned long prev, tmp;
+
+	__asm__ __volatile__ (
+		/* load conditional address in %1 to %0 */
+		"1:	lwx	%0, %2, r0;\n"
+		/* < 0 bail, release lock */
+		"	bltid	%0, 2f;\n"
+		/* increment lock by 1 */
+		"	addi	%1, %0, 1;\n"
+		/* attempt store */
+		"	swx	%1, %2, r0;\n"
+		/* checking msr carry flag */
+		"	addic	%1, r0, 0;\n"
+		/* store failed (MSR[C] set)? try again */
+		"	bnei	%1, 1b;\n"
+		"2:"
+		/* Outputs: temp variable for load result */
+		: "=&r" (prev), "=&r" (tmp)
+		/* Inputs: lock address */
+		: "r" (&rw->lock)
+		: "cc", "memory"
+	);
+	return (prev >= 0);
+}
+
+#endif /* _ASM_MICROBLAZE_SPINLOCK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/spinlock_types.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/spinlock_types.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013-2020 Xilinx, Inc.
+ */
+
+#ifndef __ASM_MICROBLAZE_SPINLOCK_TYPES_H
+#define __ASM_MICROBLAZE_SPINLOCK_TYPES_H
+
+#ifndef __LINUX_SPINLOCK_TYPES_H
+# error "please don't include this file directly"
+#endif
+
+typedef struct {
+	volatile unsigned int lock;
+} arch_spinlock_t;
+
+#define __ARCH_SPIN_LOCK_UNLOCKED	{ 0 }
+
+typedef struct {
+	volatile signed int lock;
+} arch_rwlock_t;
+
+#define __ARCH_RW_LOCK_UNLOCKED		{ 0 }
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/string.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/string.h
@@ -8,6 +8,7 @@
 
 #ifdef __KERNEL__
 
+#ifdef CONFIG_OPT_LIB_FUNCTION
 #define __HAVE_ARCH_MEMSET
 #define __HAVE_ARCH_MEMCPY
 #define __HAVE_ARCH_MEMMOVE
@@ -15,6 +16,7 @@
 extern void *memset(void *, int, __kernel_size_t);
 extern void *memcpy(void *, const void *, __kernel_size_t);
 extern void *memmove(void *, const void *, __kernel_size_t);
+#endif
 
 #endif /* __KERNEL__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/tlbflush.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/tlbflush.h
@@ -14,6 +14,8 @@
 #include <asm/mmu.h>
 #include <asm/page.h>
 
+#define MMU_NO_CONTEXT		((unsigned int)-1)
+
 extern void _tlbie(unsigned long address);
 extern void _tlbia(void);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/uaccess.h
@@ -39,24 +39,13 @@
 
 # define uaccess_kernel()	(get_fs().seg == KERNEL_DS.seg)
 
-static inline int access_ok(const void __user *addr, unsigned long size)
+static inline int __access_ok(unsigned long addr, unsigned long size)
 {
-	if (!size)
-		goto ok;
+	unsigned long limit = user_addr_max();
 
-	if ((get_fs().seg < ((unsigned long)addr)) ||
-			(get_fs().seg < ((unsigned long)addr + size - 1))) {
-		pr_devel("ACCESS fail at 0x%08x (size 0x%x), seg 0x%08x\n",
-			(__force u32)addr, (u32)size,
-			(u32)get_fs().seg);
-		return 0;
-	}
-ok:
-	pr_devel("ACCESS OK at 0x%08x (size 0x%x), seg 0x%08x\n",
-			(__force u32)addr, (u32)size,
-			(u32)get_fs().seg);
-	return 1;
+	return (size <= limit) && (addr <= (limit - size));
 }
+#define access_ok(addr, size) __access_ok((unsigned long)addr, size)
 
 # define __FIXUP_SECTION	".section .fixup,\"ax\"\n"
 # define __EX_TABLE_SECTION	".section __ex_table,\"a\"\n"
@@ -141,27 +130,27 @@
 
 #define __get_user(x, ptr)						\
 ({									\
-	unsigned long __gu_val = 0;					\
 	long __gu_err;							\
 	switch (sizeof(*(ptr))) {					\
 	case 1:								\
-		__get_user_asm("lbu", (ptr), __gu_val, __gu_err);	\
+		__get_user_asm("lbu", (ptr), x, __gu_err);		\
 		break;							\
 	case 2:								\
-		__get_user_asm("lhu", (ptr), __gu_val, __gu_err);	\
+		__get_user_asm("lhu", (ptr), x, __gu_err);		\
 		break;							\
 	case 4:								\
-		__get_user_asm("lw", (ptr), __gu_val, __gu_err);	\
+		__get_user_asm("lw", (ptr), x, __gu_err);		\
 		break;							\
-	case 8:								\
-		__gu_err = __copy_from_user(&__gu_val, ptr, 8);		\
-		if (__gu_err)						\
-			__gu_err = -EFAULT;				\
+	case 8: {							\
+		__u64 __x = 0;						\
+		__gu_err = raw_copy_from_user(&__x, ptr, 8) ?		\
+							-EFAULT : 0;	\
+		(x) = (typeof(x))(typeof((x) - (x)))__x;		\
 		break;							\
+	}								\
 	default:							\
 		/* __gu_val = 0; __gu_err = -EINVAL;*/ __gu_err = __user_bad();\
 	}								\
-	x = (__force __typeof__(*(ptr))) __gu_val;			\
 	__gu_err;							\
 })
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/include/asm/xilinx_mb_manager.h
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/include/asm/xilinx_mb_manager.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Xilinx, Inc.
+ */
+#ifndef _XILINX_MB_MANAGER_H
+#define _XILINX_MB_MANAGER_H
+
+# ifndef __ASSEMBLY__
+
+#include <linux/of_address.h>
+
+/*
+ * When the break vector gets asserted because of error injection,
+ * the break signal must be blocked before exiting from the
+ * break handler, Below api updates the manager address and
+ * control register and error counter callback arguments,
+ * which will be used by the break handler to block the
+ * break and call the callback function.
+ */
+void xmb_manager_register(uintptr_t phys_baseaddr, u32 cr_val,
+			  void (*callback)(void *data),
+			  void *priv, void (*reset_callback)(void *data));
+asmlinkage void xmb_inject_err(void);
+
+# endif /* __ASSEMBLY__ */
+
+/* Error injection offset */
+#define XMB_INJECT_ERR_OFFSET	0x200
+#define XMB_INJECT_MAGIC_VAL	0x1234abcd
+
+#endif /* _XILINX_MB_MANAGER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/Makefile
@@ -7,7 +7,6 @@
 # Do not trace early boot code and low level code
 CFLAGS_REMOVE_timer.o = -pg
 CFLAGS_REMOVE_intc.o = -pg
-CFLAGS_REMOVE_early_printk.o = -pg
 CFLAGS_REMOVE_ftrace.o = -pg
 CFLAGS_REMOVE_process.o = -pg
 endif
@@ -26,5 +25,6 @@
 obj-$(CONFIG_STACKTRACE)	+= stacktrace.o
 obj-$(CONFIG_FUNCTION_TRACER)	+= ftrace.o mcount.o
 obj-$(CONFIG_KGDB)		+= kgdb.o
+obj-$(CONFIG_SMP)		+= smp.o
 
 obj-y	+= entry.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/asm-offsets.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/asm-offsets.c
@@ -121,5 +121,12 @@
 	DEFINE(CC_FSR, offsetof(struct cpu_context, fsr));
 	BLANK();
 
+	/* struct cpuinfo */
+	DEFINE(CI_DCS, offsetof(struct cpuinfo, dcache_size));
+	DEFINE(CI_DCL, offsetof(struct cpuinfo, dcache_line_length));
+	DEFINE(CI_ICS, offsetof(struct cpuinfo, icache_size));
+	DEFINE(CI_ICL, offsetof(struct cpuinfo, icache_line_length));
+	BLANK();
+
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/cpu/cache.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/cpu/cache.c
@@ -12,6 +12,7 @@
 
 #include <asm/cacheflush.h>
 #include <linux/cache.h>
+#include <linux/smp.h>
 #include <asm/cpuinfo.h>
 #include <asm/pvr.h>
 
@@ -158,6 +159,8 @@
 
 static void __flush_icache_range_msr_irq(unsigned long start, unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -166,15 +169,15 @@
 				(unsigned int)start, (unsigned int) end);
 
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.icache_line_length, cpuinfo.icache_size);
+			cpuinfo->icache_line_length, cpuinfo->icache_size);
 
 	local_irq_save(flags);
 	__disable_icache_msr();
 
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_1(start, end, cpuinfo.icache_line_length, wic);
+	CACHE_RANGE_LOOP_1(start, end, cpuinfo->icache_line_length, wic);
 #else
-	for (i = start; i < end; i += cpuinfo.icache_line_length)
+	for (i = start; i < end; i += cpuinfo->icache_line_length)
 		__asm__ __volatile__ ("wic	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -185,6 +188,8 @@
 static void __flush_icache_range_nomsr_irq(unsigned long start,
 				unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -193,15 +198,15 @@
 				(unsigned int)start, (unsigned int) end);
 
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.icache_line_length, cpuinfo.icache_size);
+			cpuinfo->icache_line_length, cpuinfo->icache_size);
 
 	local_irq_save(flags);
 	__disable_icache_nomsr();
 
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_1(start, end, cpuinfo.icache_line_length, wic);
+	CACHE_RANGE_LOOP_1(start, end, cpuinfo->icache_line_length, wic);
 #else
-	for (i = start; i < end; i += cpuinfo.icache_line_length)
+	for (i = start; i < end; i += cpuinfo->icache_line_length)
 		__asm__ __volatile__ ("wic	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -213,6 +218,8 @@
 static void __flush_icache_range_noirq(unsigned long start,
 				unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
@@ -220,11 +227,11 @@
 				(unsigned int)start, (unsigned int) end);
 
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.icache_line_length, cpuinfo.icache_size);
+			cpuinfo->icache_line_length, cpuinfo->icache_size);
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_1(start, end, cpuinfo.icache_line_length, wic);
+	CACHE_RANGE_LOOP_1(start, end, cpuinfo->icache_line_length, wic);
 #else
-	for (i = start; i < end; i += cpuinfo.icache_line_length)
+	for (i = start; i < end; i += cpuinfo->icache_line_length)
 		__asm__ __volatile__ ("wic	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -232,6 +239,8 @@
 
 static void __flush_icache_all_msr_irq(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -241,11 +250,10 @@
 	local_irq_save(flags);
 	__disable_icache_msr();
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.icache_size, cpuinfo.icache_line_length, wic);
+	CACHE_ALL_LOOP(cpuinfo->icache_size, cpuinfo->icache_line_length, wic);
 #else
-	for (i = 0; i < cpuinfo.icache_size;
-		 i += cpuinfo.icache_line_length)
-			__asm__ __volatile__ ("wic	%0, r0;" \
+	for (i = 0; i < cpuinfo->icache_size; i += cpuinfo->icache_line_length)
+		__asm__ __volatile__ ("wic	%0, r0;" \
 					: : "r" (i));
 #endif
 	__enable_icache_msr();
@@ -254,6 +262,8 @@
 
 static void __flush_icache_all_nomsr_irq(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -263,11 +273,10 @@
 	local_irq_save(flags);
 	__disable_icache_nomsr();
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.icache_size, cpuinfo.icache_line_length, wic);
+	CACHE_ALL_LOOP(cpuinfo->icache_size, cpuinfo->icache_line_length, wic);
 #else
-	for (i = 0; i < cpuinfo.icache_size;
-		 i += cpuinfo.icache_line_length)
-			__asm__ __volatile__ ("wic	%0, r0;" \
+	for (i = 0; i < cpuinfo->icache_size; i += cpuinfo->icache_line_length)
+		__asm__ __volatile__ ("wic	%0, r0;" \
 					: : "r" (i));
 #endif
 	__enable_icache_nomsr();
@@ -276,22 +285,25 @@
 
 static void __flush_icache_all_noirq(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
 	pr_debug("%s\n", __func__);
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.icache_size, cpuinfo.icache_line_length, wic);
+	CACHE_ALL_LOOP(cpuinfo->icache_size, cpuinfo->icache_line_length, wic);
 #else
-	for (i = 0; i < cpuinfo.icache_size;
-		 i += cpuinfo.icache_line_length)
-			__asm__ __volatile__ ("wic	%0, r0;" \
+	for (i = 0; i < cpuinfo->icache_size; i += cpuinfo->icache_line_length)
+		__asm__ __volatile__ ("wic	%0, r0;" \
 					: : "r" (i));
 #endif
 }
 
 static void __invalidate_dcache_all_msr_irq(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -301,11 +313,10 @@
 	local_irq_save(flags);
 	__disable_dcache_msr();
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.dcache_size, cpuinfo.dcache_line_length, wdc);
+	CACHE_ALL_LOOP(cpuinfo->dcache_size, cpuinfo->dcache_line_length, wdc);
 #else
-	for (i = 0; i < cpuinfo.dcache_size;
-		 i += cpuinfo.dcache_line_length)
-			__asm__ __volatile__ ("wdc	%0, r0;" \
+	for (i = 0; i < cpuinfo->dcache_size; i += cpuinfo->dcache_line_length)
+		__asm__ __volatile__ ("wdc	%0, r0;" \
 					: : "r" (i));
 #endif
 	__enable_dcache_msr();
@@ -314,6 +325,8 @@
 
 static void __invalidate_dcache_all_nomsr_irq(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -323,11 +336,10 @@
 	local_irq_save(flags);
 	__disable_dcache_nomsr();
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.dcache_size, cpuinfo.dcache_line_length, wdc);
+	CACHE_ALL_LOOP(cpuinfo->dcache_size, cpuinfo->dcache_line_length, wdc);
 #else
-	for (i = 0; i < cpuinfo.dcache_size;
-		 i += cpuinfo.dcache_line_length)
-			__asm__ __volatile__ ("wdc	%0, r0;" \
+	for (i = 0; i < cpuinfo->dcache_size; i += cpuinfo->dcache_line_length)
+		__asm__ __volatile__ ("wdc	%0, r0;" \
 					: : "r" (i));
 #endif
 	__enable_dcache_nomsr();
@@ -336,16 +348,17 @@
 
 static void __invalidate_dcache_all_noirq_wt(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
 	pr_debug("%s\n", __func__);
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.dcache_size, cpuinfo.dcache_line_length, wdc);
+	CACHE_ALL_LOOP(cpuinfo->dcache_size, cpuinfo->dcache_line_length, wdc);
 #else
-	for (i = 0; i < cpuinfo.dcache_size;
-		 i += cpuinfo.dcache_line_length)
-			__asm__ __volatile__ ("wdc	%0, r0;" \
+	for (i = 0; i < cpuinfo->dcache_size; i += cpuinfo->dcache_line_length)
+		__asm__ __volatile__ ("wdc	%0, r0;" \
 					: : "r" (i));
 #endif
 }
@@ -359,17 +372,18 @@
  */
 static void __invalidate_dcache_all_wb(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
 	pr_debug("%s\n", __func__);
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.dcache_size, cpuinfo.dcache_line_length,
+	CACHE_ALL_LOOP(cpuinfo->dcache_size, cpuinfo->dcache_line_length,
 					wdc);
 #else
-	for (i = 0; i < cpuinfo.dcache_size;
-		 i += cpuinfo.dcache_line_length)
-			__asm__ __volatile__ ("wdc	%0, r0;" \
+	for (i = 0; i < cpuinfo->dcache_size; i += cpuinfo->dcache_line_length)
+		__asm__ __volatile__ ("wdc	%0, r0;" \
 					: : "r" (i));
 #endif
 }
@@ -377,6 +391,8 @@
 static void __invalidate_dcache_range_wb(unsigned long start,
 						unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
@@ -384,11 +400,11 @@
 				(unsigned int)start, (unsigned int) end);
 
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.dcache_line_length, cpuinfo.dcache_size);
+			cpuinfo->dcache_line_length, cpuinfo->dcache_size);
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_2(start, end, cpuinfo.dcache_line_length, wdc.clear);
+	CACHE_RANGE_LOOP_2(start, end, cpuinfo->dcache_line_length, wdc.clear);
 #else
-	for (i = start; i < end; i += cpuinfo.dcache_line_length)
+	for (i = start; i < end; i += cpuinfo->dcache_line_length)
 		__asm__ __volatile__ ("wdc.clear	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -397,18 +413,20 @@
 static void __invalidate_dcache_range_nomsr_wt(unsigned long start,
 							unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
 	pr_debug("%s: start 0x%x, end 0x%x\n", __func__,
 				(unsigned int)start, (unsigned int) end);
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.dcache_line_length, cpuinfo.dcache_size);
+			cpuinfo->dcache_line_length, cpuinfo->dcache_size);
 
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_1(start, end, cpuinfo.dcache_line_length, wdc);
+	CACHE_RANGE_LOOP_1(start, end, cpuinfo->dcache_line_length, wdc);
 #else
-	for (i = start; i < end; i += cpuinfo.dcache_line_length)
+	for (i = start; i < end; i += cpuinfo->dcache_line_length)
 		__asm__ __volatile__ ("wdc	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -417,6 +435,8 @@
 static void __invalidate_dcache_range_msr_irq_wt(unsigned long start,
 							unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -424,15 +444,15 @@
 	pr_debug("%s: start 0x%x, end 0x%x\n", __func__,
 				(unsigned int)start, (unsigned int) end);
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.dcache_line_length, cpuinfo.dcache_size);
+			cpuinfo->dcache_line_length, cpuinfo->dcache_size);
 
 	local_irq_save(flags);
 	__disable_dcache_msr();
 
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_1(start, end, cpuinfo.dcache_line_length, wdc);
+	CACHE_RANGE_LOOP_1(start, end, cpuinfo->dcache_line_length, wdc);
 #else
-	for (i = start; i < end; i += cpuinfo.dcache_line_length)
+	for (i = start; i < end; i += cpuinfo->dcache_line_length)
 		__asm__ __volatile__ ("wdc	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -444,6 +464,8 @@
 static void __invalidate_dcache_range_nomsr_irq(unsigned long start,
 							unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 	unsigned long flags;
 #ifndef ASM_LOOP
 	int i;
@@ -452,15 +474,15 @@
 				(unsigned int)start, (unsigned int) end);
 
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.dcache_line_length, cpuinfo.dcache_size);
+			cpuinfo->dcache_line_length, cpuinfo->dcache_size);
 
 	local_irq_save(flags);
 	__disable_dcache_nomsr();
 
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_1(start, end, cpuinfo.dcache_line_length, wdc);
+	CACHE_RANGE_LOOP_1(start, end, cpuinfo->dcache_line_length, wdc);
 #else
-	for (i = start; i < end; i += cpuinfo.dcache_line_length)
+	for (i = start; i < end; i += cpuinfo->dcache_line_length)
 		__asm__ __volatile__ ("wdc	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -471,23 +493,26 @@
 
 static void __flush_dcache_all_wb(void)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
 	pr_debug("%s\n", __func__);
 #ifdef ASM_LOOP
-	CACHE_ALL_LOOP(cpuinfo.dcache_size, cpuinfo.dcache_line_length,
+	CACHE_ALL_LOOP(cpuinfo->dcache_size, cpuinfo->dcache_line_length,
 				wdc.flush);
 #else
-	for (i = 0; i < cpuinfo.dcache_size;
-		 i += cpuinfo.dcache_line_length)
-			__asm__ __volatile__ ("wdc.flush	%0, r0;" \
+	for (i = 0; i < cpuinfo->dcache_size; i += cpuinfo->dcache_line_length)
+		__asm__ __volatile__ ("wdc.flush	%0, r0;" \
 					: : "r" (i));
 #endif
 }
 
 static void __flush_dcache_range_wb(unsigned long start, unsigned long end)
 {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
 #ifndef ASM_LOOP
 	int i;
 #endif
@@ -495,11 +520,11 @@
 				(unsigned int)start, (unsigned int) end);
 
 	CACHE_LOOP_LIMITS(start, end,
-			cpuinfo.dcache_line_length, cpuinfo.dcache_size);
+			cpuinfo->dcache_line_length, cpuinfo->dcache_size);
 #ifdef ASM_LOOP
-	CACHE_RANGE_LOOP_2(start, end, cpuinfo.dcache_line_length, wdc.flush);
+	CACHE_RANGE_LOOP_2(start, end, cpuinfo->dcache_line_length, wdc.flush);
 #else
-	for (i = start; i < end; i += cpuinfo.dcache_line_length)
+	for (i = start; i < end; i += cpuinfo->dcache_line_length)
 		__asm__ __volatile__ ("wdc.flush	%0, r0;"	\
 				: : "r" (i));
 #endif
@@ -608,16 +633,19 @@
 
 void microblaze_cache_init(void)
 {
-	if (cpuinfo.use_instr & PVR2_USE_MSR_INSTR) {
-		if (cpuinfo.dcache_wb) {
+	unsigned int cpu = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
+
+	if (cpuinfo->use_instr & PVR2_USE_MSR_INSTR) {
+		if (cpuinfo->dcache_wb) {
 			pr_info("wb_msr\n");
 			mbc = (struct scache *)&wb_msr;
-			if (cpuinfo.ver_code <= CPUVER_7_20_D) {
+			if (cpuinfo->ver_code <= CPUVER_7_20_D) {
 				/* MS: problem with signal handling - hw bug */
 				pr_info("WB won't work properly\n");
 			}
 		} else {
-			if (cpuinfo.ver_code >= CPUVER_7_20_A) {
+			if (cpuinfo->ver_code >= CPUVER_7_20_A) {
 				pr_info("wt_msr_noirq\n");
 				mbc = (struct scache *)&wt_msr_noirq;
 			} else {
@@ -626,15 +654,15 @@
 			}
 		}
 	} else {
-		if (cpuinfo.dcache_wb) {
+		if (cpuinfo->dcache_wb) {
 			pr_info("wb_nomsr\n");
 			mbc = (struct scache *)&wb_nomsr;
-			if (cpuinfo.ver_code <= CPUVER_7_20_D) {
+			if (cpuinfo->ver_code <= CPUVER_7_20_D) {
 				/* MS: problem with signal handling - hw bug */
 				pr_info("WB won't work properly\n");
 			}
 		} else {
-			if (cpuinfo.ver_code >= CPUVER_7_20_A) {
+			if (cpuinfo->ver_code >= CPUVER_7_20_A) {
 				pr_info("wt_nomsr_noirq\n");
 				mbc = (struct scache *)&wt_nomsr_noirq;
 			} else {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/cpu/cpuinfo-static.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/cpu/cpuinfo-static.c
@@ -18,7 +18,7 @@
 static const char cpu_ver_string[] = CONFIG_XILINX_MICROBLAZE0_HW_VER;
 
 #define err_printk(x) \
-	early_printk("ERROR: Microblaze " x "-different for kernel and DTS\n");
+	pr_err("ERROR: Microblaze " x "-different for kernel and DTS\n");
 
 void __init set_cpuinfo_static(struct cpuinfo *ci, struct device_node *cpu)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/cpu/cpuinfo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/cpu/cpuinfo.c
@@ -1,4 +1,5 @@
 /*
+ * Copyright (C) 2013-2020 Xilinx, Inc. All rights reserved.
  * Copyright (C) 2007-2009 Michal Simek <monstr@monstr.eu>
  * Copyright (C) 2007-2009 PetaLogix
  * Copyright (C) 2007 John Williams <john.williams@petalogix.com>
@@ -10,6 +11,7 @@
 
 #include <linux/clk.h>
 #include <linux/init.h>
+#include <linux/smp.h>
 #include <asm/cpuinfo.h>
 #include <asm/pvr.h>
 
@@ -56,7 +58,7 @@
 };
 
 /*
- * FIXME Not sure if the actual key is defined by Xilinx in the PVR
+ * The actual key is defined by Xilinx in the PVR
  */
 const struct family_string_key family_string_lookup[] = {
 	{"virtex2", 0x4},
@@ -85,37 +87,40 @@
 	{NULL, 0},
 };
 
-struct cpuinfo cpuinfo;
-static struct device_node *cpu;
+DEFINE_PER_CPU(struct cpuinfo, cpu_info);
 
 void __init setup_cpuinfo(void)
 {
-	cpu = of_get_cpu_node(0, NULL);
+	struct device_node *cpu;
+	unsigned int cpu_id = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu_id);
+
+	cpu = of_get_cpu_node(cpu_id, NULL);
 	if (!cpu)
 		pr_err("You don't have cpu or are missing cpu reg property!!!\n");
 
-	pr_info("%s: initialising\n", __func__);
+	pr_info("%s: initialising cpu %d\n", __func__, cpu_id);
 
 	switch (cpu_has_pvr()) {
 	case 0:
 		pr_warn("%s: No PVR support. Using static CPU info from FDT\n",
 			__func__);
-		set_cpuinfo_static(&cpuinfo, cpu);
+		set_cpuinfo_static(cpuinfo, cpu);
 		break;
 /* FIXME I found weird behavior with MB 7.00.a/b 7.10.a
  * please do not use FULL PVR with MMU */
 	case 1:
 		pr_info("%s: Using full CPU PVR support\n",
 			__func__);
-		set_cpuinfo_static(&cpuinfo, cpu);
-		set_cpuinfo_pvr_full(&cpuinfo, cpu);
+		set_cpuinfo_static(cpuinfo, cpu);
+		set_cpuinfo_pvr_full(cpuinfo, cpu);
 		break;
 	default:
 		pr_warn("%s: Unsupported PVR setting\n", __func__);
-		set_cpuinfo_static(&cpuinfo, cpu);
+		set_cpuinfo_static(cpuinfo, cpu);
 	}
 
-	if (cpuinfo.mmu_privins)
+	if (cpuinfo->mmu_privins)
 		pr_warn("%s: Stream instructions enabled"
 			" - USERSPACE CAN LOCK THIS KERNEL!\n", __func__);
 
@@ -125,17 +130,24 @@
 void __init setup_cpuinfo_clk(void)
 {
 	struct clk *clk;
+	struct device_node *cpu;
+	unsigned int cpu_id = smp_processor_id();
+	struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu_id);
+
+	cpu = of_get_cpu_node(cpu_id, NULL);
+	if (!cpu)
+		pr_err("You don't have cpu or are missing cpu reg property!!!\n");
 
 	clk = of_clk_get(cpu, 0);
 	if (IS_ERR(clk)) {
 		pr_err("ERROR: CPU CCF input clock not found\n");
 		/* take timebase-frequency from DTS */
-		cpuinfo.cpu_clock_freq = fcpu(cpu, "timebase-frequency");
+		cpuinfo->cpu_clock_freq = fcpu(cpu, "timebase-frequency");
 	} else {
-		cpuinfo.cpu_clock_freq = clk_get_rate(clk);
+		cpuinfo->cpu_clock_freq = clk_get_rate(clk);
 	}
 
-	if (!cpuinfo.cpu_clock_freq) {
+	if (!cpuinfo->cpu_clock_freq) {
 		pr_err("ERROR: CPU clock frequency not setup\n");
 		BUG();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/cpu/mb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/cpu/mb.c
@@ -1,6 +1,7 @@
 /*
  * CPU-version specific code
  *
+ * Copyright (C) 2013-2020 Xilinx, Inc. All rights reserved
  * Copyright (C) 2007-2009 Michal Simek <monstr@monstr.eu>
  * Copyright (C) 2006-2009 PetaLogix
  *
@@ -27,117 +28,135 @@
 
 static int show_cpuinfo(struct seq_file *m, void *v)
 {
-	char *fpga_family = "Unknown";
-	char *cpu_ver = "Unknown";
-	int i;
-
-	/* Denormalised to get the fpga family string */
-	for (i = 0; family_string_lookup[i].s != NULL; i++) {
-		if (cpuinfo.fpga_family_code == family_string_lookup[i].k) {
-			fpga_family = (char *)family_string_lookup[i].s;
-			break;
+	unsigned int cpu;
+
+	for_each_online_cpu(cpu) {
+		struct cpuinfo *cpuinfo = per_cpu_ptr(&cpu_info, cpu);
+		char *fpga_family = "Unknown";
+		char *cpu_ver = "Unknown";
+		int i;
+
+		/* Denormalised to get the fpga family string */
+		for (i = 0; family_string_lookup[i].s != NULL; i++) {
+			if (cpuinfo->fpga_family_code ==
+			    family_string_lookup[i].k) {
+				fpga_family = (char *)family_string_lookup[i].s;
+				break;
+			}
 		}
-	}
 
-	/* Denormalised to get the hw version string */
-	for (i = 0; cpu_ver_lookup[i].s != NULL; i++) {
-		if (cpuinfo.ver_code == cpu_ver_lookup[i].k) {
-			cpu_ver = (char *)cpu_ver_lookup[i].s;
-			break;
+		/* Denormalised to get the hw version string */
+		for (i = 0; cpu_ver_lookup[i].s != NULL; i++) {
+			if (cpuinfo->ver_code == cpu_ver_lookup[i].k) {
+				cpu_ver = (char *)cpu_ver_lookup[i].s;
+				break;
+			}
 		}
-	}
 
-	seq_printf(m,
-		   "CPU-Family:	MicroBlaze\n"
-		   "FPGA-Arch:	%s\n"
-		   "CPU-Ver:	%s, %s endian\n"
-		   "CPU-MHz:	%d.%02d\n"
-		   "BogoMips:	%lu.%02lu\n",
-		   fpga_family,
-		   cpu_ver,
-		   cpuinfo.endian ? "little" : "big",
-		   cpuinfo.cpu_clock_freq / 1000000,
-		   cpuinfo.cpu_clock_freq % 1000000,
-		   loops_per_jiffy / (500000 / HZ),
-		   (loops_per_jiffy / (5000 / HZ)) % 100);
-
-	seq_printf(m,
-		   "HW:\n Shift:\t\t%s\n"
-		   " MSR:\t\t%s\n"
-		   " PCMP:\t\t%s\n"
-		   " DIV:\t\t%s\n",
-		   (cpuinfo.use_instr & PVR0_USE_BARREL_MASK) ? "yes" : "no",
-		   (cpuinfo.use_instr & PVR2_USE_MSR_INSTR) ? "yes" : "no",
-		   (cpuinfo.use_instr & PVR2_USE_PCMP_INSTR) ? "yes" : "no",
-		   (cpuinfo.use_instr & PVR0_USE_DIV_MASK) ? "yes" : "no");
-
-	seq_printf(m, " MMU:\t\t%x\n", cpuinfo.mmu);
-
-	seq_printf(m,
-		   " MUL:\t\t%s\n"
-		   " FPU:\t\t%s\n",
-		   (cpuinfo.use_mult & PVR2_USE_MUL64_MASK) ? "v2" :
-		   (cpuinfo.use_mult & PVR0_USE_HW_MUL_MASK) ? "v1" : "no",
-		   (cpuinfo.use_fpu & PVR2_USE_FPU2_MASK) ? "v2" :
-		   (cpuinfo.use_fpu & PVR0_USE_FPU_MASK) ? "v1" : "no");
-
-	seq_printf(m,
-		   " Exc:\t\t%s%s%s%s%s%s%s%s\n",
-		   (cpuinfo.use_exc & PVR2_OPCODE_0x0_ILL_MASK) ? "op0x0 " : "",
-		   (cpuinfo.use_exc & PVR2_UNALIGNED_EXC_MASK) ? "unal " : "",
-		   (cpuinfo.use_exc & PVR2_ILL_OPCODE_EXC_MASK) ? "ill " : "",
-		   (cpuinfo.use_exc & PVR2_IOPB_BUS_EXC_MASK) ? "iopb " : "",
-		   (cpuinfo.use_exc & PVR2_DOPB_BUS_EXC_MASK) ? "dopb " : "",
-		   (cpuinfo.use_exc & PVR2_DIV_ZERO_EXC_MASK) ? "zero " : "",
-		   (cpuinfo.use_exc & PVR2_FPU_EXC_MASK) ? "fpu " : "",
-		   (cpuinfo.use_exc & PVR2_USE_FSL_EXC) ? "fsl " : "");
-
-	seq_printf(m,
-		   "Stream-insns:\t%sprivileged\n",
-		   cpuinfo.mmu_privins ? "un" : "");
-
-	if (cpuinfo.use_icache)
-		seq_printf(m,
-			   "Icache:\t\t%ukB\tline length:\t%dB\n",
-			   cpuinfo.icache_size >> 10,
-			   cpuinfo.icache_line_length);
-	else
-		seq_puts(m, "Icache:\t\tno\n");
-
-	if (cpuinfo.use_dcache) {
-		seq_printf(m,
-			   "Dcache:\t\t%ukB\tline length:\t%dB\n",
-			   cpuinfo.dcache_size >> 10,
-			   cpuinfo.dcache_line_length);
-		seq_puts(m, "Dcache-Policy:\t");
-		if (cpuinfo.dcache_wb)
-			seq_puts(m, "write-back\n");
+		seq_printf(m,
+			"Processor:	%u\n"
+			"CPU-Family:	MicroBlaze\n"
+			"FPGA-Arch:	%s\n"
+			"CPU-Ver:	%s, %s endian\n"
+			"CPU-MHz:	%d.%02d\n"
+			"BogoMips:	%lu.%02lu\n",
+			cpu,
+			fpga_family,
+			cpu_ver,
+			cpuinfo->endian ? "little" : "big",
+			cpuinfo->cpu_clock_freq / 1000000,
+			cpuinfo->cpu_clock_freq % 1000000,
+			loops_per_jiffy / (500000 / HZ),
+			(loops_per_jiffy / (5000 / HZ)) % 100);
+
+		seq_printf(m,
+			"HW:\n Shift:\t\t%s\n"
+			" MSR:\t\t%s\n"
+			" PCMP:\t\t%s\n"
+			" DIV:\t\t%s\n",
+			(cpuinfo->use_instr & PVR0_USE_BARREL_MASK) ?
+			"yes" : "no",
+			(cpuinfo->use_instr & PVR2_USE_MSR_INSTR) ?
+			"yes" : "no",
+			(cpuinfo->use_instr & PVR2_USE_PCMP_INSTR) ?
+			"yes" : "no",
+			(cpuinfo->use_instr & PVR0_USE_DIV_MASK) ?
+			"yes" : "no");
+
+		seq_printf(m, " MMU:\t\t%x\n", cpuinfo->mmu);
+
+		seq_printf(m,
+			" MUL:\t\t%s\n"
+			" FPU:\t\t%s\n",
+			(cpuinfo->use_mult & PVR2_USE_MUL64_MASK) ? "v2" :
+			(cpuinfo->use_mult & PVR0_USE_HW_MUL_MASK) ?
+			"v1" : "no",
+			(cpuinfo->use_fpu & PVR2_USE_FPU2_MASK) ? "v2" :
+			(cpuinfo->use_fpu & PVR0_USE_FPU_MASK) ? "v1" : "no");
+
+		seq_printf(m,
+			" Exc:\t\t%s%s%s%s%s%s%s%s\n",
+			(cpuinfo->use_exc & PVR2_OPCODE_0x0_ILL_MASK) ?
+			"op0x0 " : "",
+			(cpuinfo->use_exc & PVR2_UNALIGNED_EXC_MASK) ?
+			"unal " : "",
+			(cpuinfo->use_exc & PVR2_ILL_OPCODE_EXC_MASK) ?
+			"ill " : "",
+			(cpuinfo->use_exc & PVR2_IOPB_BUS_EXC_MASK) ?
+			"iopb " : "",
+			(cpuinfo->use_exc & PVR2_DOPB_BUS_EXC_MASK) ?
+			"dopb " : "",
+			(cpuinfo->use_exc & PVR2_DIV_ZERO_EXC_MASK) ?
+			"zero " : "",
+			(cpuinfo->use_exc & PVR2_FPU_EXC_MASK) ? "fpu " : "",
+			(cpuinfo->use_exc & PVR2_USE_FSL_EXC) ? "fsl " : "");
+
+		seq_printf(m,
+			"Stream-insns:\t%sprivileged\n",
+			cpuinfo->mmu_privins ? "un" : "");
+
+		if (cpuinfo->use_icache)
+			seq_printf(m,
+				"Icache:\t\t%ukB\tline length:\t%dB\n",
+				cpuinfo->icache_size >> 10,
+				cpuinfo->icache_line_length);
 		else
-			seq_puts(m, "write-through\n");
-	} else {
-		seq_puts(m, "Dcache:\t\tno\n");
-	}
+			seq_puts(m, "Icache:\t\tno\n");
 
-	seq_printf(m,
-		   "HW-Debug:\t%s\n",
-		   cpuinfo.hw_debug ? "yes" : "no");
-
-	seq_printf(m,
-		   "PVR-USR1:\t%02x\n"
-		   "PVR-USR2:\t%08x\n",
-		   cpuinfo.pvr_user1,
-		   cpuinfo.pvr_user2);
+		if (cpuinfo->use_dcache) {
+			seq_printf(m,
+				"Dcache:\t\t%ukB\tline length:\t%dB\n",
+				cpuinfo->dcache_size >> 10,
+				cpuinfo->dcache_line_length);
+			seq_puts(m, "Dcache-Policy:\t");
+			if (cpuinfo->dcache_wb)
+				seq_puts(m, "write-back\n");
+			else
+				seq_puts(m, "write-through\n");
+		} else {
+			seq_puts(m, "Dcache:\t\tno\n");
+		}
 
-	seq_printf(m, "Page size:\t%lu\n", PAGE_SIZE);
+		seq_printf(m,
+			"HW-Debug:\t%s\n",
+			cpuinfo->hw_debug ? "yes" : "no");
+
+		seq_printf(m,
+			"PVR-USR1:\t%02x\n"
+			"PVR-USR2:\t%08x\n",
+			cpuinfo->pvr_user1,
+			cpuinfo->pvr_user2);
+
+		seq_printf(m, "Page size:\t%lu\n", PAGE_SIZE);
+		seq_puts(m, "\n");
+	}
 
 	return 0;
 }
 
 static void *c_start(struct seq_file *m, loff_t *pos)
 {
-	int i = *pos;
-
-	return i < NR_CPUS ? (void *) (i + 1) : NULL;
+	return *pos < 1 ? (void *) 1 : NULL;
 }
 
 static void *c_next(struct seq_file *m, void *v, loff_t *pos)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/entry.S
@@ -27,9 +27,11 @@
 
 #include <asm/page.h>
 #include <asm/unistd.h>
+#include <asm/xilinx_mb_manager.h>
 
 #include <linux/errno.h>
 #include <asm/signal.h>
+#include <asm/mmu.h>
 
 #undef DEBUG
 
@@ -42,6 +44,11 @@
 	.space	(__NR_syscalls * 4)
 #endif /* DEBUG */
 
+#ifdef CONFIG_SMP
+#define CURRENT_SAVE	CURRENT_SAVE_ADDR
+#define ENTRY_SP	ENTRY_SP_ADDR
+#endif /* CONFIG_SMP */
+
 #define C_ENTRY(name)	.globl name; .align 4; name
 
 /*
@@ -91,6 +98,10 @@
 	.macro	clear_vms_ums
 	msrclr	r0, MSR_VMS | MSR_UMS
 	.endm
+
+	.macro	save_clear_vm
+	msrclr	r11, MSR_VM
+	.endm
 #else
 	.macro	clear_bip
 	mfs	r11, rmsr
@@ -153,6 +164,12 @@
 	andni	r11, r11, (MSR_VMS|MSR_UMS)
 	mts	rmsr,r11
 	.endm
+
+	.macro	save_clear_vm
+	mfs	r11, rmsr
+	andni	r11, r11, MSR_VM
+	mts	rmsr,r11
+	.endm
 #endif
 
 /* Define how to call high-level functions. With MMU, virtual mode must be
@@ -252,15 +269,32 @@
 	mts	rmsr , r11;						\
 	RESTORE_REGS_GP
 
+#ifndef CONFIG_SMP
+#define LOAD_PER_CPU(reg, addr)		lwi reg, r0, TOPHYS(PER_CPU(addr));
+#define STORE_PER_CPU(reg, addr)	swi reg, r0, TOPHYS(PER_CPU(addr));
+#define STORE_PER_CPU_VM(reg, addr)	swi reg, r0, PER_CPU(addr);
+#else
+#define LOAD_PER_CPU(reg, addr)		lwi reg, r0, PER_CPU(addr);
+#define STORE_PER_CPU(reg, addr)	swi reg, r0, PER_CPU(addr);
+#define STORE_PER_CPU_VM(reg, addr)	\
+	save_clear_vm;			\
+	bri	TOPHYS(1f);		\
+1:					\
+	swi	reg, r0, PER_CPU(addr);	\
+	mts	rmsr, r11;		\
+	bri	__phys_to_virt(2f);	\
+2:
+#endif /* CONFIG_SMP */
+
 #define SAVE_STATE	\
-	swi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP)); /* save stack */	\
+	STORE_PER_CPU(r1, ENTRY_SP) /* save stack */			\
 	/* See if already in kernel mode.*/				\
 	mfs	r1, rmsr;						\
 	andi	r1, r1, MSR_UMS;					\
 	bnei	r1, 1f;						\
 	/* Kernel-mode state save.  */					\
 	/* Reload kernel stack-ptr. */					\
-	lwi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP));			\
+	LOAD_PER_CPU(r1, ENTRY_SP)					\
 	/* FIXME: I can add these two lines to one */			\
 	/* tophys(r1,r1); */						\
 	/* addik	r1, r1, -PT_SIZE; */				\
@@ -269,7 +303,7 @@
 	brid	2f;							\
 	swi	r1, r1, PT_MODE; 	 				\
 1:	/* User-mode state save.  */					\
-	lwi	r1, r0, TOPHYS(PER_CPU(CURRENT_SAVE)); /* get saved current */\
+	LOAD_PER_CPU(r1, CURRENT_SAVE)	/* get saved current */		\
 	tophys(r1,r1);							\
 	lwi	r1, r1, TS_THREAD_INFO;	/* get the thread info */	\
 	/* MS these three instructions can be added to one */		\
@@ -278,15 +312,53 @@
 	/* addik	r1, r1, -PT_SIZE; */			\
 	addik r1, r1, THREAD_SIZE + CONFIG_KERNEL_BASE_ADDR - CONFIG_KERNEL_START - PT_SIZE; \
 	SAVE_REGS							\
-	lwi	r11, r0, TOPHYS(PER_CPU(ENTRY_SP));			\
+	LOAD_PER_CPU(r11, ENTRY_SP)					\
 	swi	r11, r1, PT_R1; /* Store user SP.  */		\
 	swi	r0, r1, PT_MODE; /* Was in user-mode.  */		\
 	/* MS: I am clearing UMS even in case when I come from kernel space */ \
 	clear_ums; 							\
-2:	lwi	CURRENT_TASK, r0, TOPHYS(PER_CPU(CURRENT_SAVE));
+2:	LOAD_PER_CPU(CURRENT_TASK, CURRENT_SAVE)
 
 .text
 
+.extern cpu_info
+
+C_ENTRY(mb_flush_dcache):
+	addik	r1, r1, -PT_SIZE
+	SAVE_REGS
+
+	addik	r3, r0, cpu_info
+	lwi	r7, r3, CI_DCS
+	lwi	r8, r3, CI_DCL
+	sub	r9, r7, r8
+1:
+	wdc.flush r9, r0
+	bgtid	r9, 1b
+	addk	r9, r9, r8
+
+	RESTORE_REGS
+	addik	r1, r1, PT_SIZE
+	rtsd	r15, 8
+	nop
+
+C_ENTRY(mb_invalidate_icache):
+	addik	r1, r1, -PT_SIZE
+	SAVE_REGS
+
+	addik	r3, r0, cpu_info
+	lwi	r7, r3, CI_ICS
+	lwi	r8, r3, CI_ICL
+	sub	r9, r7, r8
+1:
+	wic 	r9, r0
+	bgtid	r9, 1b
+	addk	r9, r9, r8
+
+	RESTORE_REGS
+	addik	r1, r1, PT_SIZE
+	rtsd	r15, 8
+	nop
+
 /*
  * User trap.
  *
@@ -300,10 +372,10 @@
  * are masked. This is nice, means we don't have to CLI before state save
  */
 C_ENTRY(_user_exception):
-	swi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP)) /* save stack */
+	STORE_PER_CPU(r1, ENTRY_SP) /* save stack */
 	addi	r14, r14, 4	/* return address is 4 byte after call */
 
-	lwi	r1, r0, TOPHYS(PER_CPU(CURRENT_SAVE)); /* get saved current */
+	LOAD_PER_CPU(r1, CURRENT_SAVE); /* get saved current */
 	tophys(r1,r1);
 	lwi	r1, r1, TS_THREAD_INFO;	/* get stack from task_struct */
 /* calculate kernel stack pointer from task struct 8k */
@@ -316,10 +388,10 @@
 	swi	r0, r1, PT_R4
 
 	swi	r0, r1, PT_MODE;			/* Was in user-mode. */
-	lwi	r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
+	LOAD_PER_CPU(r11, ENTRY_SP);
 	swi	r11, r1, PT_R1;		/* Store user SP.  */
 	clear_ums;
-2:	lwi	CURRENT_TASK, r0, TOPHYS(PER_CPU(CURRENT_SAVE));
+2:	LOAD_PER_CPU(CURRENT_TASK, CURRENT_SAVE);
 	/* Save away the syscall number.  */
 	swi	r12, r1, PT_R0;
 	tovirt(r1,r1)
@@ -434,8 +506,8 @@
 
 /* Finally, return to user state.  */
 4:	set_bip;			/*  Ints masked for state restore */
-	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE); /* save current */
 	VM_OFF;
+	STORE_PER_CPU(CURRENT_TASK, CURRENT_SAVE); /* save current */
 	tophys(r1,r1);
 	RESTORE_REGS_RTBD;
 	addik	r1, r1, PT_SIZE		/* Clean up stack space.  */
@@ -462,8 +534,8 @@
    saved context).  */
 C_ENTRY(ret_from_fork):
 	bralid	r15, schedule_tail; /* ...which is schedule_tail's arg */
-	add	r5, r3, r0;	/* switch_thread returns the prev task */
-				/* ( in the delay slot ) */
+	add	r5, r3, r0;	/* Arg 0: _switch_to places prev task struct */
+				/* pointer in r3 in the delay slot ) */
 	brid	ret_from_trap;	/* Do normal trap return */
 	add	r3, r0, r0;	/* Child's fork call should return 0. */
 
@@ -519,11 +591,11 @@
 	 * are used and they use r0 instead of r11.
 	 * I am using ENTRY_SP which should be primary used only for stack
 	 * pointer saving. */
-	swi	r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
+	STORE_PER_CPU(r11, ENTRY_SP);
 	set_bip;        /* equalize initial state for all possible entries */
 	clear_eip;
 	set_ee;
-	lwi	r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
+	LOAD_PER_CPU(r11, ENTRY_SP);
 	SAVE_STATE		/* Save registers.*/
 	/* PC, before IRQ/trap - this is one instruction above */
 	swi	r17, r1, PT_PC;
@@ -618,8 +690,8 @@
 
 /* Finally, return to user state.  */
 4:	set_bip;			/* Ints masked for state restore */
-	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE); /* save current */
 	VM_OFF;
+	STORE_PER_CPU(CURRENT_TASK, CURRENT_SAVE); /* save current */
 	tophys(r1,r1);
 
 	RESTORE_REGS_RTBD;
@@ -653,7 +725,7 @@
 C_ENTRY(_interrupt):
 /* MS: we are in physical address */
 /* Save registers, switch to proper stack, convert SP to virtual.*/
-	swi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP))
+	STORE_PER_CPU(r1, ENTRY_SP)
 	/* MS: See if already in kernel mode. */
 	mfs	r1, rmsr
 	nop
@@ -661,7 +733,7 @@
 	bnei	r1, 1f
 
 /* Kernel-mode state save. */
-	lwi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP))
+	LOAD_PER_CPU(r1, ENTRY_SP)
 	tophys(r1,r1); /* MS: I have in r1 physical address where stack is */
 	/* save registers */
 /* MS: Make room on the stack -> activation record */
@@ -672,7 +744,7 @@
 1:
 /* User-mode state save. */
  /* MS: get the saved current */
-	lwi	r1, r0, TOPHYS(PER_CPU(CURRENT_SAVE));
+	LOAD_PER_CPU(r1, CURRENT_SAVE);
 	tophys(r1,r1);
 	lwi	r1, r1, TS_THREAD_INFO;
 	addik	r1, r1, THREAD_SIZE;
@@ -682,11 +754,11 @@
 	SAVE_REGS
 	/* calculate mode */
 	swi	r0, r1, PT_MODE;
-	lwi	r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
+	LOAD_PER_CPU(r11, ENTRY_SP);
 	swi	r11, r1, PT_R1;
 	clear_ums;
 2:
-	lwi	CURRENT_TASK, r0, TOPHYS(PER_CPU(CURRENT_SAVE));
+	LOAD_PER_CPU(CURRENT_TASK, CURRENT_SAVE);
 	tovirt(r1,r1)
 	addik	r15, r0, irq_call;
 irq_call:rtbd	r0, do_IRQ;
@@ -719,8 +791,8 @@
 no_intr_resched:
     /* Disable interrupts, we are now committed to the state restore */
 	disable_irq
-	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE);
 	VM_OFF;
+	STORE_PER_CPU(CURRENT_TASK, CURRENT_SAVE);
 	tophys(r1,r1);
 	RESTORE_REGS
 	addik	r1, r1, PT_SIZE /* MS: Clean up stack space. */
@@ -753,20 +825,174 @@
 	rtid	r14, 0
 	nop
 
+#ifdef CONFIG_MB_MANAGER
+
+#define	PT_PID		PT_SIZE
+#define	PT_TLBI		PT_SIZE + 4
+#define	PT_ZPR		PT_SIZE	+ 8
+#define	PT_TLBL0	PT_SIZE + 12
+#define	PT_TLBH0	PT_SIZE + 16
+
+C_ENTRY(_xtmr_manager_reset):
+	lwi	r1, r0, TOPHYS(xmb_manager_stackpointer)
+
+	/* Restore MSR */
+	lwi	r2, r1, PT_MSR
+	mts	rmsr, r2
+	bri	4
+
+	/* restore Special purpose registers */
+	lwi	r2, r1, PT_PID
+	mts	rpid, r2
+
+	lwi	r2, r1, PT_TLBI
+	mts	rtlbx, r2
+
+	lwi	r2, r1, PT_ZPR
+	mts	rzpr, r2
+
+#if CONFIG_XILINX_MICROBLAZE0_USE_FPU
+	lwi	r2, r1, PT_FSR
+	mts	rfsr, r2
+#endif
+
+	/* restore all the tlb's */
+	addik	r3, r0, TOPHYS(tlb_skip)
+	addik	r6, r0, PT_TLBL0
+	addik	r7, r0, PT_TLBH0
+restore_tlb:
+	add	r6, r6, r1
+	add	r7, r7, r1
+	lwi	r2, r6, 0
+	mts 	rtlblo, r2
+	lwi	r2, r7, 0
+	mts	rtlbhi, r2
+	addik	r6, r6, 4
+	addik	r7, r7, 4
+	bgtid	r3, restore_tlb
+	addik	r3, r3, -1
+
+	lwi  	r5, r0, TOPHYS(xmb_manager_dev)
+	lwi	r8, r0, TOPHYS(xmb_manager_reset_callback)
+	tovirt(r1, r1)
+	set_vms
+	/* return from reset need -8 to adjust for rtsd r15, 8 */
+	addik   r15, r0, ret_from_reset - 8
+	rtbd	r8, 0
+	nop
+
+ret_from_reset:
+	set_bip /* Ints masked for state restore */
+	VM_OFF
+	tophys(r1, r1)
+	/* MS: Restore all regs */
+	RESTORE_REGS
+	lwi	r14, r1, PT_R14
+	lwi	r16, r1, PT_PC
+	addik	r1, r1, PT_SIZE + 36
+	tovirt(r1,r1)
+	rtbd	r16, 0
+	nop
+
+C_ENTRY(_xmb_manager_break):
+	/*
+	 * Reserve memory in the stack for context store/restore
+	 * (which includes memory for storing tlbs (max two tlbs))
+	 */
+	addik	r1, r1, CONFIG_KERNEL_BASE_ADDR - CONFIG_KERNEL_START - PT_SIZE - 36
+	swi	r1, r0, TOPHYS(xmb_manager_stackpointer)
+	SAVE_REGS
+	swi	r0, r1, PT_R0;	/* R0 must be saved too */
+	swi	r14, r1, PT_R14	/* rewrite saved R14 value */
+	swi	r16, r1, PT_PC; /* PC and r16 are the same */
+
+	lwi	r6, r0, TOPHYS(xmb_manager_baseaddr)
+	lwi	r7, r0, TOPHYS(xmb_manager_crval)
+	/*
+	 * When the break vector gets asserted because of error injection,
+	 * the break signal must be blocked before exiting from the
+	 * break handler, below code configures the tmr manager
+	 * control register to block break signal.
+	 */
+	swi	r7, r6, 0
+
+	/* Save the special purpose registers  */
+	mfs	r2, rpid
+	swi	r2, r1, PT_PID
+
+	mfs	r2, rtlbx
+	swi	r2, r1, PT_TLBI
+
+	mfs	r2, rzpr
+	swi	r2, r1, PT_ZPR
+
+#if CONFIG_XILINX_MICROBLAZE0_USE_FPU
+	mfs	r2, rfsr
+	swi	r2, r1, PT_FSR
+#endif
+	mfs	r2, rmsr
+	swi	r2, r1, PT_MSR
+
+	/* Save all the tlb's */
+	addik	r3, r0, TOPHYS(tlb_skip)
+	addik	r6, r0, PT_TLBL0
+	addik	r7, r0, PT_TLBH0
+save_tlb:
+	add	r6, r6, r1
+	add	r7, r7, r1
+	mfs	r2, rtlblo
+	swi	r2, r6, 0
+	mfs	r2, rtlbhi
+	swi	r2, r7, 0
+	addik	r6, r6, 4
+	addik	r7, r7, 4
+	bgtid	r3, save_tlb
+	addik	r3, r3, -1
+
+	lwi  	r5, r0, TOPHYS(xmb_manager_dev)
+	lwi	r8, r0, TOPHYS(xmb_manager_callback)
+	tovirt(r1, r1)
+	/* return from break need -8 to adjust for rtsd r15, 8 */
+	addik   r15, r0, ret_from_break - 8
+	rtbd	r8, 0
+	nop
+
+ret_from_break:
+	/* flush the d-cache */
+	bralid	r15, mb_flush_dcache
+	nop
+
+	/*
+	 * To make sure microblaze i-cache is in a proper state
+	 * invalidate the i-cache.
+	 */
+	bralid	r15, mb_invalidate_icache
+	nop
+
+	set_bip; /* Ints masked for state restore */
+	VM_OFF;
+	tophys(r1,r1)
+	mbar	1
+	mbar	2
+	bri	4
+	suspend
+	nop
+#endif
+
 /*
  * Debug trap for KGDB. Enter to _debug_exception by brki r16, 0x18
  * and call handling function with saved pt_regs
  */
 C_ENTRY(_debug_exception):
 	/* BIP bit is set on entry, no interrupts can occur */
-	swi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP))
+	STORE_PER_CPU(r1, ENTRY_SP)
 
 	mfs	r1, rmsr
 	nop
 	andi	r1, r1, MSR_UMS
 	bnei	r1, 1f
 /* MS: Kernel-mode state save - kgdb */
-	lwi	r1, r0, TOPHYS(PER_CPU(ENTRY_SP)); /* Reload kernel stack-ptr*/
+	LOAD_PER_CPU(r1, ENTRY_SP); /* Reload kernel stack-ptr*/
 
 	/* BIP bit is set on entry, no interrupts can occur */
 	addik   r1, r1, CONFIG_KERNEL_BASE_ADDR - CONFIG_KERNEL_START - PT_SIZE;
@@ -800,7 +1026,7 @@
 	bri 0
 
 /* MS: User-mode state save - gdb */
-1:	lwi	r1, r0, TOPHYS(PER_CPU(CURRENT_SAVE)); /* get saved current */
+1:	LOAD_PER_CPU(r1, CURRENT_SAVE); /* get saved current */
 	tophys(r1,r1);
 	lwi	r1, r1, TS_THREAD_INFO;	/* get the thread info */
 	addik	r1, r1, THREAD_SIZE;	/* calculate kernel stack pointer */
@@ -810,9 +1036,9 @@
 	SAVE_REGS;
 	swi	r16, r1, PT_PC;	/* Save LP */
 	swi	r0, r1, PT_MODE; /* Was in user-mode.  */
-	lwi	r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
+	LOAD_PER_CPU(r11, ENTRY_SP);
 	swi	r11, r1, PT_R1; /* Store user SP.  */
-	lwi	CURRENT_TASK, r0, TOPHYS(PER_CPU(CURRENT_SAVE));
+	LOAD_PER_CPU(CURRENT_TASK, CURRENT_SAVE);
 	tovirt(r1,r1)
 	set_vms;
 	addik	r5, r1, 0;
@@ -848,8 +1074,8 @@
 	bri	1b
 
 /* Finally, return to user state.  */
-4:	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE); /* save current */
-	VM_OFF;
+4:	VM_OFF;
+	STORE_PER_CPU(CURRENT_TASK, CURRENT_SAVE); /* save current */
 	tophys(r1,r1);
 	/* MS: Restore all regs */
 	RESTORE_REGS_RTBD
@@ -918,7 +1144,7 @@
 	/* update r31, the current-give me pointer to task which will be next */
 	lwi	CURRENT_TASK, r6, TI_TASK
 	/* stored it to current_save too */
-	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE)
+	STORE_PER_CPU_VM(CURRENT_TASK, CURRENT_SAVE)
 
 	/* get new process' cpu context and restore */
 	/* give me start where start context of next task */
@@ -957,6 +1183,84 @@
 	rtsd	r15, 8
 	nop
 
+#ifdef CONFIG_MB_MANAGER
+.global xmb_inject_err
+.section .text
+.align 2
+.ent xmb_inject_err
+.type xmb_inject_err, @function
+xmb_inject_err:
+	addik	r1, r1, -PT_SIZE
+	SAVE_REGS
+
+	/* Switch to real mode */
+	VM_OFF;
+	set_bip;
+	mbar	1
+	mbar	2
+	bralid	r15, XMB_INJECT_ERR_OFFSET
+	nop;
+
+	/* enable virtual mode */
+	set_vms;
+	/* barrier for instructions and data accesses */
+	mbar	1
+	mbar	2
+	rtbd    r0, 1f
+	nop;
+1:
+	RESTORE_REGS
+	addik	r1, r1, PT_SIZE
+	rtsd	r15, 8;
+	nop;
+.end xmb_inject_err
+
+.section .data
+.global xmb_manager_dev
+.global xmb_manager_baseaddr
+.global xmb_manager_crval
+.global xmb_manager_callback
+.global xmb_manager_reset_callback
+.global xmb_manager_stackpointer
+.align 4
+xmb_manager_dev:
+	.long 0
+xmb_manager_baseaddr:
+	.long 0
+xmb_manager_crval:
+	.long 0
+xmb_manager_callback:
+	.long 0
+xmb_manager_reset_callback:
+	.long 0
+xmb_manager_stackpointer:
+	.long 0
+
+/*
+ * When the break vector gets asserted because of error injection,
+ * the break signal must be blocked before exiting from the
+ * break handler, Below api updates the manager address and
+ * control register and error count callback arguments,
+ * which will be used by the break handler to block the
+ * break and call the callback function.
+ */
+.global xmb_manager_register
+.section .text
+.align 2
+.ent xmb_manager_register
+.type xmb_manager_register, @function
+xmb_manager_register:
+	swi	r5, r0, xmb_manager_baseaddr
+	swi	r6, r0, xmb_manager_crval
+	swi	r7, r0, xmb_manager_callback
+	swi	r8, r0, xmb_manager_dev
+	swi	r9, r0, xmb_manager_reset_callback
+
+	rtsd	r15, 8;
+	nop;
+.end xmb_manager_register
+#endif
+
 ENTRY(_reset)
 	VM_OFF
 	brai	0; /* Jump to reset vector */
@@ -964,19 +1268,43 @@
 	/* These are compiled and loaded into high memory, then
 	 * copied into place in mach_early_setup */
 	.section	.init.ivt, "ax"
-#if CONFIG_MANUAL_RESET_VECTOR
+#if CONFIG_MANUAL_RESET_VECTOR && !defined(CONFIG_MB_MANAGER)
 	.org	0x0
 	brai	CONFIG_MANUAL_RESET_VECTOR
+#elif defined(CONFIG_MB_MANAGER)
+	.org	0x0
+	brai	TOPHYS(_xtmr_manager_reset);
 #endif
 	.org	0x8
 	brai	TOPHYS(_user_exception); /* syscall handler */
 	.org	0x10
 	brai	TOPHYS(_interrupt);	/* Interrupt handler */
+#ifdef CONFIG_MB_MANAGER
+	.org	0x18
+	brai	TOPHYS(_xmb_manager_break);	/* microblaze manager break handler */
+#else
 	.org	0x18
 	brai	TOPHYS(_debug_exception);	/* debug trap handler */
+#endif
 	.org	0x20
 	brai	TOPHYS(_hw_exception_handler);	/* HW exception handler */
 
+#ifdef CONFIG_MB_MANAGER
+	/*
+	 * For TMR Inject API which injects the error should
+	 * be executed from LMB.
+	 * TMR Inject is programmed with address of 0x200 so that
+	 * when program counter matches with this address error will
+	 * be injected. 0x200 is expected to be next available bram
+	 * offset, hence used for this api.
+	 */
+	.org	XMB_INJECT_ERR_OFFSET
+xmb_inject_error:
+	nop
+	rtsd	r15, 8
+	nop
+#endif
+
 .section .rodata,"a"
 #include "syscall_table.S"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/exceptions.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/exceptions.c
@@ -44,10 +44,10 @@
 	pr_warn("Oops: %s, sig: %ld\n", str, err);
 	show_regs(fp);
 	spin_unlock_irq(&die_lock);
-	/* do_exit() should take care of panic'ing from an interrupt
+	/* make_task_dead() should take care of panic'ing from an interrupt
 	 * context so we don't handle it here
 	 */
-	do_exit(err);
+	make_task_dead(err);
 }
 
 /* for user application debugging */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/head.S
@@ -30,6 +30,7 @@
 
 #include <linux/init.h>
 #include <linux/linkage.h>
+#include <asm/entry.h>
 #include <asm/thread_info.h>
 #include <asm/page.h>
 #include <linux/of_fdt.h>		/* for OF_DT_HEADER */
@@ -37,6 +38,7 @@
 #include <asm/setup.h> /* COMMAND_LINE_SIZE */
 #include <asm/mmu.h>
 #include <asm/processor.h>
+#include <asm/asm-offsets.h>
 
 .section .data
 .global empty_zero_page
@@ -46,6 +48,11 @@
 .global swapper_pg_dir
 swapper_pg_dir:
 	.space	PAGE_SIZE
+#ifdef CONFIG_SMP
+temp_boot_stack:
+	.space	1024
+#define CURRENT_SAVE	CURRENT_SAVE_ADDR
+#endif /* CONFIG_SMP */
 
 .section .rodata
 .align 4
@@ -76,6 +83,13 @@
 	msrclr	r8, 0 /* clear nothing - just read msr for test */
 	cmpu	r8, r8, r1 /* r1 must contain msr reg content */
 
+#ifdef CONFIG_SMP
+	/* skip FDT copy if secondary */
+	mfs	r11, rpvr0
+	andi	r11, r11, 0xFF
+	bnei	r11, _setup_initial_mmu
+#endif /* CONFIG_SMP */
+
 /* r7 may point to an FDT, or there may be one linked in.
    if it's in r7, we've got to save it away ASAP.
    We ensure r7 points to a valid FDT, just in case the bootloader
@@ -142,6 +156,7 @@
 #endif
 	/* We have to turn on the MMU right away. */
 
+_setup_initial_mmu:
 	/*
 	 * Set up the initial MMU state so we can do the first level of
 	 * kernel initialization.  This maps the first 16 MBytes of memory 1:1
@@ -173,9 +188,8 @@
 	tophys(r4,r3)			/* Load the kernel physical address */
 
 	/* start to do TLB calculation */
-	addik	r12, r0, _end
+	addik	r12, r0, _end_tlb_mapping
 	rsub	r12, r3, r12
-	addik	r12, r12, CONFIG_LOWMEM_SIZE >> PTE_SHIFT /* that's the pad */
 
 	or r9, r0, r0 /* TLB0 = 0 */
 	or r10, r0, r0 /* TLB1 = 0 */
@@ -317,6 +331,18 @@
 	 */
 turn_on_mmu:
 	ori	r15,r0,start_here
+#ifdef CONFIG_SMP
+	/*
+	 * Read PVR and mask off all but CPU id bits to use to select
+	 * boot sequence
+	 */
+	mfs	r4, rpvr0
+	andi	r4, r4, 0xFF
+
+	beqi	r4, finish
+	ori	r15, r0, start_secondary_cpu
+finish:
+#endif /* CONFIG_SMP */
 	ori	r4,r0,MSR_KERNEL_VMS
 	mts	rmsr,r4
 	nop
@@ -334,6 +360,10 @@
 
 	/* Initialize r31 with current task address */
 	addik	r31, r0, init_task
+#ifdef CONFIG_MMU
+	/* save current for CPU 0 */
+	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE);
+#endif
 
 	addik	r11, r0, machine_early_init
 	brald	r15, r11
@@ -372,3 +402,61 @@
 	nop
 	rted	r17, 0		/* enable MMU and jump to start_kernel */
 	nop
+
+#ifdef CONFIG_SMP
+/* Entry point for secondary processors */
+start_secondary_cpu:
+
+	/* Initialize small data anchors */
+	addik	r13, r0, _KERNEL_SDA_BASE_
+	addik	r2, r0, _KERNEL_SDA2_BASE_
+
+	/* Initialize stack pointer */
+	addik	r1, r0, temp_boot_stack + 1024 - 4
+
+	/*
+	 * Initialize the exception table.
+	 */
+	addik	r11, r0, secondary_machine_init
+	brald	r15, r11
+	nop
+
+	lwi	r1, r0, secondary_ti
+
+	/* Initialize r31 with current task address */
+	lwi	CURRENT_TASK, r1, TI_TASK
+	/* save current for secondary CPU */
+	swi	CURRENT_TASK, r0, PER_CPU(CURRENT_SAVE);
+
+	/* Initialize stack pointer */
+	addi	r1, r1, THREAD_SIZE - 4
+	swi	r0, r1, 0
+
+	/* Initialize MMU */
+	ori	r11, r0, 0x10000000
+	mts	rzpr, r11
+
+	ori	r15, r0, TOPHYS(kernel_load_context_secondary)
+	ori	r4, r0, MSR_KERNEL
+	mts	rmsr, r4
+	nop
+	bri	4
+	rted	r15, 0
+	nop
+
+	/* Load up the kernel context */
+kernel_load_context_secondary:
+	# Keep entry 0 and 1 valid. Entry 3 mapped to LMB can go away.
+	ori	r5, r0, MICROBLAZE_LMB_TLB_ID
+	mts     rtlbx, r5
+	nop
+	mts	rtlbhi, r0
+	nop
+	addi	r15, r0, machine_halt
+	ori	r17, r0, start_secondary
+	ori	r4, r0, MSR_KERNEL_VMS
+	mts	rmsr, r4
+	nop
+	rted	r17, 0		/* enable MMU and jump to start_kernel */
+	nop
+#endif /* CONFIG_SMP */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/hw_exception_handler.S
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/hw_exception_handler.S
@@ -243,10 +243,15 @@
  */
 
 /* wrappers to restore state before coming to entry.S */
+#ifdef CONFIG_SMP
+#define CURRENT_SAVE  __phys_to_virt(CURRENT_SAVE_ADDR)
+#define pt_pool_space __phys_to_virt(PT_POOL_SPACE_ADDR)
+#else
 .section .data
 .align 4
 pt_pool_space:
 	.space	PT_SIZE
+#endif /* CONFIG_SMP */
 
 #ifdef DEBUG
 /* Create space for exception counting. */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/irq.c
@@ -20,29 +20,10 @@
 #include <linux/irqchip.h>
 #include <linux/of_irq.h>
 
-static u32 concurrent_irq;
-
 void __irq_entry do_IRQ(struct pt_regs *regs)
 {
-	unsigned int irq;
-	struct pt_regs *old_regs = set_irq_regs(regs);
 	trace_hardirqs_off();
-
-	irq_enter();
-	irq = xintc_get_irq();
-next_irq:
-	BUG_ON(!irq);
-	generic_handle_irq(irq);
-
-	irq = xintc_get_irq();
-	if (irq != -1U) {
-		pr_debug("next irq: %d\n", irq);
-		++concurrent_irq;
-		goto next_irq;
-	}
-
-	irq_exit();
-	set_irq_regs(old_regs);
+	handle_arch_irq(regs);
 	trace_hardirqs_on();
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/kgdb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/kgdb.c
@@ -8,6 +8,7 @@
 
 #include <linux/kgdb.h>
 #include <linux/kdebug.h>
+#include <linux/smp.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <asm/cacheflush.h>
@@ -105,6 +106,13 @@
 		gdb_regs[GDB_PVR + i] = pvr.pvr[i];
 }
 
+#ifdef CONFIG_SMP
+void kgdb_roundup_cpus(void)
+{
+	smp_send_debugger_break();
+}
+#endif
+
 void kgdb_arch_set_pc(struct pt_regs *regs, unsigned long ip)
 {
 	regs->pc = ip;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/setup.c
@@ -29,17 +29,30 @@
 #include <linux/pci.h>
 #include <linux/cache.h>
 #include <linux/of.h>
+#include <linux/smp.h>
 #include <linux/dma-mapping.h>
 #include <asm/cacheflush.h>
 #include <asm/entry.h>
 #include <asm/cpuinfo.h>
 
 
+#ifdef CONFIG_SMP
+static void __init smp_setup_cpu_maps(void)
+{
+	int i;
+
+	for (i = 0; i < NR_CPUS; i++) {
+		set_cpu_present(i, true);
+		set_cpu_possible(i, true);
+	}
+}
+#else
 DEFINE_PER_CPU(unsigned int, KSP);	/* Saved kernel stack pointer */
 DEFINE_PER_CPU(unsigned int, KM);	/* Kernel/user mode */
 DEFINE_PER_CPU(unsigned int, ENTRY_SP);	/* Saved SP on kernel entry */
 DEFINE_PER_CPU(unsigned int, R11_SAVE);	/* Temp variable for entry */
 DEFINE_PER_CPU(unsigned int, CURRENT_SAVE);	/* Saved current pointer */
+#endif /* CONFIG_SMP */
 
 /*
  * Placed cmd_line to .data section because can be initialized from
@@ -63,6 +76,10 @@
 	microblaze_cache_init();
 
 	xilinx_pci_init();
+
+#ifdef CONFIG_SMP
+	smp_setup_cpu_maps();
+#endif
 }
 
 #ifdef CONFIG_MTD_UCLINUX
@@ -132,7 +149,7 @@
 	if (fdt)
 		pr_info("FDT at 0x%08x\n", fdt);
 	else
-		pr_info("Compiled-in FDT at %p\n", _fdt_start);
+		pr_info("Compiled-in FDT at 0x%08x\n", (unsigned)&_fdt_start);
 
 #ifdef CONFIG_MTD_UCLINUX
 	pr_info("Found romfs @ 0x%08x (0x%08x)\n",
@@ -169,8 +186,10 @@
 		*dst = *src;
 
 	/* Initialize global data */
+#ifndef CONFIG_SMP
 	per_cpu(KM, 0) = 0x1;	/* We start in kernel mode */
 	per_cpu(CURRENT_SAVE, 0) = (unsigned long)current;
+#endif
 }
 
 void __init time_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/smp.c
@@ -0,0 +1,335 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * SMP support for MicroBlaze, borrowing a great
+ * deal of code from the PowerPC implementation
+ *
+ * Copyright (C) 1999 Cort Dougan <cort@cs.nmt.edu>
+ * Copyright (C) 2013-2020 Xilinx, Inc.
+ */
+
+#include <linux/atomic.h>
+#include <linux/cpu.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/profile.h>
+#include <linux/sched/task.h>
+#include <linux/seq_file.h>
+#include <linux/smp.h>
+
+#include <asm/barrier.h>
+#include <asm/cacheflush.h>
+#include <asm/cpuinfo.h>
+#include <asm/tlbflush.h>
+
+struct thread_info *secondary_ti;
+
+static struct thread_info *current_set[NR_CPUS];
+
+unsigned long irq_err_count;
+
+static unsigned int boot_cpuid;
+
+DEFINE_PER_CPU_SHARED_ALIGNED(irq_cpustat_t, irq_stat);
+EXPORT_SYMBOL(irq_stat);
+
+static DEFINE_PER_CPU(cpumask_var_t, cpu_core_map);
+
+static volatile unsigned int cpu_callin_map[NR_CPUS];
+
+static void (*crash_ipi_function_ptr)(struct pt_regs *);
+
+static const char * const smp_ipi_name[] = {
+	[MICROBLAZE_MSG_RESCHEDULE] = "ipi reschedule",
+	[MICROBLAZE_MSG_CALL_FUNCTION] = "ipi call function",
+	[MICROBLAZE_MSG_CALL_FUNCTION_SINGLE] = "ipi call function single",
+	[MICROBLAZE_MSG_DEBUGGER_BREAK] = "ipi debugger",
+};
+
+/* Functions for recording IPI handler */
+static void (*__smp_cross_call)(unsigned int, unsigned int);
+
+void __init set_smp_cross_call(void (*fn)(unsigned int, unsigned int))
+{
+	if (!__smp_cross_call)
+		__smp_cross_call = fn;
+}
+
+static inline struct cpumask *cpu_core_mask(int cpu)
+{
+	return per_cpu(cpu_core_map, cpu);
+}
+
+u64 smp_irq_stat_cpu(unsigned int cpu)
+{
+	u64 sum = 0;
+	int i;
+
+	for (i = 0; i < MICROBLAZE_NUM_IPIS; i++)
+		sum += __get_irq_stat(cpu, ipi_irqs[i]);
+
+	return sum;
+}
+
+static void show_ipi_list(struct seq_file *p, int prec)
+{
+	unsigned int cpu, i;
+
+	for (i = 0; i < MICROBLAZE_NUM_IPIS; i++) {
+		seq_printf(p, "%*s%u:%s", prec - 1, "IPI", i,
+			prec >= 4 ? " " : "");
+		for_each_online_cpu(cpu)
+			seq_printf(p, "%10u ",
+				__get_irq_stat(cpu, ipi_irqs[i]));
+		seq_printf(p, " %s\n", smp_ipi_name[i]);
+	}
+}
+
+int arch_show_interrupts(struct seq_file *p, int prec)
+{
+	show_ipi_list(p, prec);
+	seq_printf(p, "%*s: %10lu\n", prec, "Err", irq_err_count);
+	return 0;
+}
+
+void handle_IPI(int ipinr, struct pt_regs *regs)
+{
+	struct pt_regs *old_regs = set_irq_regs(regs);
+	unsigned int cpu = smp_processor_id();
+
+	pr_debug("%s: cpu: %d got IPI: %d\n", __func__, cpu, ipinr);
+
+	__inc_irq_stat(cpu, ipi_irqs[ipinr]);
+
+	switch (ipinr) {
+	case MICROBLAZE_MSG_RESCHEDULE:
+		scheduler_ipi();
+		break;
+	case MICROBLAZE_MSG_CALL_FUNCTION:
+		generic_smp_call_function_interrupt();
+		break;
+	case MICROBLAZE_MSG_CALL_FUNCTION_SINGLE:
+		generic_smp_call_function_single_interrupt();
+		break;
+	case MICROBLAZE_MSG_DEBUGGER_BREAK:
+		if (crash_ipi_function_ptr)
+			crash_ipi_function_ptr(get_irq_regs());
+		break;
+	default:
+		BUG();
+	}
+
+	set_irq_regs(old_regs);
+}
+
+void smp_send_reschedule(int cpu)
+{
+	if (cpu_online(cpu))
+		__smp_cross_call(cpu, MICROBLAZE_MSG_RESCHEDULE);
+}
+
+void arch_send_call_function_single_ipi(int cpu)
+{
+	if (cpu_online(cpu))
+		__smp_cross_call(cpu, MICROBLAZE_MSG_CALL_FUNCTION_SINGLE);
+}
+
+void arch_send_call_function_ipi_mask(const struct cpumask *mask)
+{
+	unsigned int cpu;
+
+	for_each_cpu(cpu, mask)
+		__smp_cross_call(cpu, MICROBLAZE_MSG_CALL_FUNCTION);
+}
+
+#ifdef CONFIG_KGDB
+void smp_send_debugger_break(void)
+{
+	int cpu;
+	int me = raw_smp_processor_id();
+
+	for_each_online_cpu(cpu)
+		if (cpu != me)
+			__smp_cross_call(cpu, MICROBLAZE_MSG_DEBUGGER_BREAK);
+}
+
+void crash___smp_cross_call(void (*crash_ipi_callback)(struct pt_regs *))
+{
+	crash_ipi_function_ptr = crash_ipi_callback;
+	if (crash_ipi_callback) {
+		mb();
+		smp_send_debugger_break();
+	}
+}
+#endif
+
+static void stop_this_cpu(void *dummy)
+{
+	/* Remove this CPU */
+	set_cpu_online(smp_processor_id(), false);
+
+	local_irq_disable();
+	while (1)
+		;
+}
+
+void smp_send_stop(void)
+{
+	smp_call_function(stop_this_cpu, NULL, 0);
+}
+
+static void __init smp_create_idle(unsigned int cpu)
+{
+	struct task_struct *p;
+
+	/* create a process for the processor */
+	p = fork_idle(cpu);
+	if (IS_ERR(p)) {
+		panic("failed fork for CPU %u: %li", cpu, PTR_ERR(p));
+		pr_alert("failed to create cpu %d idle\n", cpu);
+	}
+
+	task_thread_info(p)->cpu = cpu;
+	current_set[cpu] = task_thread_info(p);
+
+}
+
+void __init smp_prepare_cpus(unsigned int max_cpus)
+{
+	unsigned int cpu;
+
+	/*
+	 * setup_cpu may need to be called on the boot cpu. We havent
+	 * spun any cpus up but lets be paranoid.
+	 */
+	BUG_ON(boot_cpuid != smp_processor_id());
+
+	/* Fixup boot cpu */
+	cpu_callin_map[boot_cpuid] = 1;
+
+	for_each_possible_cpu(cpu) {
+		zalloc_cpumask_var_node(&per_cpu(cpu_core_map, cpu),
+					GFP_KERNEL, cpu_to_node(cpu));
+	}
+
+	cpumask_set_cpu(boot_cpuid, cpu_core_mask(boot_cpuid));
+
+	max_cpus = NR_CPUS;
+
+	for_each_possible_cpu(cpu) {
+		if (cpu != boot_cpuid)
+			smp_create_idle(cpu);
+	}
+}
+
+void __init smp_prepare_boot_cpu(void)
+{
+	BUG_ON(smp_processor_id() != boot_cpuid);
+	current_set[boot_cpuid] = task_thread_info(current);
+}
+
+int __cpu_up(unsigned int cpu, struct task_struct *tidle)
+{
+	int c;
+
+	secondary_ti = current_set[cpu];
+
+	/*
+	 * Make sure callin-map entry is 0 (can be leftover a CPU
+	 * hotplug
+	 */
+	cpu_callin_map[cpu] = 0;
+
+	/*
+	 * The information for processor bringup must
+	 * be written out to main store before we release
+	 * the processor.
+	 */
+	smp_mb();
+
+	/* wake up cpu */
+	pr_alert("From cpu %d: Waking CPU %d\n", smp_processor_id(), cpu);
+
+	__smp_cross_call(cpu, 0);
+
+	if (system_state < SYSTEM_RUNNING)
+		for (c = 10000; c && !cpu_callin_map[cpu]; c--)
+			udelay(100);
+
+	if (!cpu_callin_map[cpu]) {
+		pr_err("Processor %u is stuck.\n", cpu);
+		return -ENOENT;
+	}
+
+	while (!cpu_online(cpu))
+		cpu_relax();
+
+	pr_alert("Processor %u found.\n", cpu);
+
+	return 0;
+}
+
+asmlinkage void __init secondary_machine_init(void)
+{
+	unsigned long *src, *dst;
+	unsigned int offset = 0;
+
+	/*
+	 * Do not copy reset vectors. offset = 0x2 means skip the first
+	 * two instructions. dst is pointer to MB vectors which are placed
+	 * in block ram. If you want to copy reset vector setup offset to 0x0
+	 */
+#if !CONFIG_MANUAL_RESET_VECTOR
+	offset = 0x2;
+#endif
+	dst = (unsigned long *) (offset * sizeof(u32));
+	for (src = __ivt_start + offset; src < __ivt_end; src++, dst++)
+		*dst = *src;
+}
+
+/* Activate a secondary processor. */
+void __init start_secondary(void) // FIXME this is not __init
+{
+	unsigned int cpu = smp_processor_id();
+	int i;
+
+	atomic_inc(&init_mm.mm_count);
+	current->active_mm = &init_mm;
+	cpumask_set_cpu(cpu, mm_cpumask(&init_mm));
+	local_flush_tlb_mm(&init_mm);
+
+	pr_alert("cpu: %d alive\n", cpu);
+
+	setup_cpuinfo();
+	microblaze_cache_init();
+
+	preempt_disable();
+
+	/* calibrate_delay(); */
+
+	cpu_callin_map[cpu] = 1;
+
+	notify_cpu_starting(cpu);
+
+	set_cpu_online(cpu, true);
+
+	for_each_online_cpu(i) {
+		cpumask_set_cpu(cpu, cpu_core_mask(i));
+		cpumask_set_cpu(i, cpu_core_mask(cpu));
+	}
+	local_irq_enable();
+
+	cpu_startup_entry(CPUHP_AP_ONLINE_IDLE);
+
+	BUG();
+}
+
+#ifdef CONFIG_PROFILING
+int setup_profiling_timer(unsigned int multiplier)
+{
+	return 0;
+}
+#endif
+
+void __init smp_cpus_done(unsigned int max_cpus)
+{ }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/timer.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/timer.c
@@ -16,15 +16,22 @@
 #include <linux/sched_clock.h>
 #include <linux/clk.h>
 #include <linux/clockchips.h>
+#include <linux/cpuhotplug.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/timecounter.h>
 #include <asm/cpuinfo.h>
 
-static void __iomem *timer_baseaddr;
+static void __iomem *clocksource_baseaddr;
 
-static unsigned int freq_div_hz;
-static unsigned int timer_clock_freq;
+struct xilinx_timer {
+	void __iomem *timer_baseaddr;
+	u32 irq;
+	unsigned int freq_div_hz;
+	unsigned int timer_clock_freq;
+};
+
+static DEFINE_PER_CPU(struct xilinx_timer, timer_priv);
 
 #define TCSR0	(0x00)
 #define TLR0	(0x04)
@@ -70,12 +77,21 @@
 
 static inline void xilinx_timer0_stop(void)
 {
+	int cpu = smp_processor_id();
+	struct xilinx_timer *timer = per_cpu_ptr(&timer_priv, cpu);
+	void __iomem *timer_baseaddr = timer->timer_baseaddr;
+
 	write_fn(read_fn(timer_baseaddr + TCSR0) & ~TCSR_ENT,
 		 timer_baseaddr + TCSR0);
 }
 
-static inline void xilinx_timer0_start_periodic(unsigned long load_val)
+static inline void xilinx_timer0_start_periodic(void)
 {
+	int cpu = smp_processor_id();
+	struct xilinx_timer *timer = per_cpu_ptr(&timer_priv, cpu);
+	void __iomem *timer_baseaddr = timer->timer_baseaddr;
+	unsigned long load_val = timer->freq_div_hz;
+
 	if (!load_val)
 		load_val = 1;
 	/* loading value to timer reg */
@@ -103,6 +119,10 @@
 
 static inline void xilinx_timer0_start_oneshot(unsigned long load_val)
 {
+	int cpu = smp_processor_id();
+	struct xilinx_timer *timer = per_cpu_ptr(&timer_priv, cpu);
+	void __iomem *timer_baseaddr = timer->timer_baseaddr;
+
 	if (!load_val)
 		load_val = 1;
 	/* loading value to timer reg */
@@ -133,11 +153,11 @@
 static int xilinx_timer_set_periodic(struct clock_event_device *evt)
 {
 	pr_info("%s\n", __func__);
-	xilinx_timer0_start_periodic(freq_div_hz);
+	xilinx_timer0_start_periodic();
 	return 0;
 }
 
-static struct clock_event_device clockevent_xilinx_timer = {
+static DEFINE_PER_CPU(struct clock_event_device, clockevent_xilinx_timer) = {
 	.name			= "xilinx_clockevent",
 	.features		= CLOCK_EVT_FEAT_ONESHOT |
 				  CLOCK_EVT_FEAT_PERIODIC,
@@ -150,37 +170,75 @@
 
 static inline void timer_ack(void)
 {
+	int cpu = smp_processor_id();
+	struct xilinx_timer *timer = per_cpu_ptr(&timer_priv, cpu);
+	void __iomem *timer_baseaddr = timer->timer_baseaddr;
+
 	write_fn(read_fn(timer_baseaddr + TCSR0), timer_baseaddr + TCSR0);
 }
 
 static irqreturn_t timer_interrupt(int irq, void *dev_id)
 {
-	struct clock_event_device *evt = &clockevent_xilinx_timer;
+	struct clock_event_device *evt = dev_id;
+
 	timer_ack();
 	evt->event_handler(evt);
 	return IRQ_HANDLED;
 }
 
-static __init int xilinx_clockevent_init(void)
+static __init int xilinx_clockevent_init(int cpu, struct xilinx_timer *timer)
 {
-	clockevent_xilinx_timer.mult =
-		div_sc(timer_clock_freq, NSEC_PER_SEC,
-				clockevent_xilinx_timer.shift);
-	clockevent_xilinx_timer.max_delta_ns =
-		clockevent_delta2ns((u32)~0, &clockevent_xilinx_timer);
-	clockevent_xilinx_timer.max_delta_ticks = (u32)~0;
-	clockevent_xilinx_timer.min_delta_ns =
-		clockevent_delta2ns(1, &clockevent_xilinx_timer);
-	clockevent_xilinx_timer.min_delta_ticks = 1;
-	clockevent_xilinx_timer.cpumask = cpumask_of(0);
-	clockevents_register_device(&clockevent_xilinx_timer);
+	struct clock_event_device *ce = per_cpu_ptr(&clockevent_xilinx_timer,
+						    cpu);
+
+	ce->mult = div_sc(timer->timer_clock_freq, NSEC_PER_SEC, ce->shift);
+	ce->max_delta_ns = clockevent_delta2ns((u32)~0, ce);
+	ce->max_delta_ticks = (u32)~0;
+	ce->min_delta_ns = clockevent_delta2ns(1, ce);
+	ce->min_delta_ticks = 1;
+	ce->cpumask = cpumask_of(cpu);
+	clockevents_register_device(ce);
+
+	return 0;
+}
+
+static int microblaze_timer_starting(unsigned int cpu)
+{
+	int ret;
+	struct xilinx_timer *timer = per_cpu_ptr(&timer_priv, cpu);
+	struct clock_event_device *ce = per_cpu_ptr(&clockevent_xilinx_timer,
+						    cpu);
+
+	pr_debug("%s: cpu %d\n", __func__, cpu);
+
+	if (!timer->timer_baseaddr) {
+		/* It should never fail */
+		pr_err("%s: clockevent timer for cpu %d failed\n",
+		       __func__, cpu);
+		return -EINVAL;
+	}
+
+	ret = request_irq(timer->irq, timer_interrupt, IRQF_TIMER |
+			  IRQF_PERCPU | IRQF_NOBALANCING,
+			  "timer", ce);
+	if (ret) {
+		pr_err("%s: request_irq failed\n", __func__);
+		return ret;
+	}
+
+	return xilinx_clockevent_init(cpu, timer);
+}
+
+static int microblaze_timer_dying(unsigned int cpu)
+{
+	pr_debug("%s: cpu %d\n", __func__, cpu);
 
 	return 0;
 }
 
 static u64 xilinx_clock_read(void)
 {
-	return read_fn(timer_baseaddr + TCR1);
+	return read_fn(clocksource_baseaddr + TCR0);
 }
 
 static u64 xilinx_read(struct clocksource *cs)
@@ -204,16 +262,6 @@
 	.shift = 8,
 };
 
-static int __init init_xilinx_timecounter(void)
-{
-	xilinx_cc.mult = div_sc(timer_clock_freq, NSEC_PER_SEC,
-				xilinx_cc.shift);
-
-	timecounter_init(&xilinx_tc, &xilinx_cc, sched_clock());
-
-	return 0;
-}
-
 static struct clocksource clocksource_microblaze = {
 	.name		= "xilinx_clocksource",
 	.rating		= 300,
@@ -222,7 +270,7 @@
 	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-static int __init xilinx_clocksource_init(void)
+static int __init xilinx_clocksource_init(unsigned int timer_clock_freq)
 {
 	int ret;
 
@@ -234,27 +282,61 @@
 	}
 
 	/* stop timer1 */
-	write_fn(read_fn(timer_baseaddr + TCSR1) & ~TCSR_ENT,
-		 timer_baseaddr + TCSR1);
+	write_fn(read_fn(clocksource_baseaddr + TCSR0) & ~TCSR_ENT,
+		 clocksource_baseaddr + TCSR0);
 	/* start timer1 - up counting without interrupt */
-	write_fn(TCSR_TINT|TCSR_ENT|TCSR_ARHT, timer_baseaddr + TCSR1);
+	write_fn(TCSR_TINT|TCSR_ENT|TCSR_ARHT, clocksource_baseaddr + TCSR0);
 
 	/* register timecounter - for ftrace support */
-	return init_xilinx_timecounter();
+	xilinx_cc.mult = div_sc(timer_clock_freq, NSEC_PER_SEC,
+				xilinx_cc.shift);
+
+	timecounter_init(&xilinx_tc, &xilinx_cc, sched_clock());
+
+	sched_clock_register(xilinx_clock_read, 32, timer_clock_freq);
+
+	return 0;
 }
 
 static int __init xilinx_timer_init(struct device_node *timer)
 {
 	struct clk *clk;
 	static int initialized;
-	u32 irq;
 	u32 timer_num = 1;
-	int ret;
-
-	if (initialized)
-		return -EINVAL;
+	int ret = 0, cpu_id = 0;
+	void __iomem *timer_baseaddr;
+	unsigned int timer_clock_freq;
+	bool clocksource = false;
+	bool clockevent = false;
+
+	ret = of_property_read_u32(timer, "cpu-id", (u32 *)&cpu_id);
+	if (!ret && NR_CPUS > 1) {
+		/* cpu_id will say if this is clocksource or clockevent */
+		if (cpu_id >= NR_CPUS)
+			clocksource = true;
+		else
+			clockevent = true;
+	} else {
+		/* No cpu_id property continue to work in old style */
+		clocksource = true;
+		clockevent = true;
+	}
 
-	initialized = 1;
+	if (clocksource) {
+		/* TODO Add support for clocksource from one timer only */
+		ret = of_property_read_u32(timer, "xlnx,one-timer-only",
+					   &timer_num);
+		if (ret) {
+			pr_err("%pOF: missing %s property\n",
+				timer, "xlnx,one-timer-only");
+			return -EINVAL;
+		}
+
+		if (timer_num) {
+			pr_err("%pOF: Please enable two timers in HW\n", timer);
+			return -EINVAL;
+		}
+	}
 
 	timer_baseaddr = of_iomap(timer, 0);
 	if (!timer_baseaddr) {
@@ -271,20 +353,6 @@
 		read_fn = timer_read32_be;
 	}
 
-	irq = irq_of_parse_and_map(timer, 0);
-	if (irq <= 0) {
-		pr_err("Failed to parse and map irq");
-		return -EINVAL;
-	}
-
-	of_property_read_u32(timer, "xlnx,one-timer-only", &timer_num);
-	if (timer_num) {
-		pr_err("Please enable two timers in HW\n");
-		return -EINVAL;
-	}
-
-	pr_info("%pOF: irq=%d\n", timer, irq);
-
 	clk = of_clk_get(timer, 0);
 	if (IS_ERR(clk)) {
 		pr_err("ERROR: timer CCF input clock not found\n");
@@ -297,29 +365,65 @@
 
 	if (!timer_clock_freq) {
 		pr_err("ERROR: Using CPU clock frequency\n");
-		timer_clock_freq = cpuinfo.cpu_clock_freq;
+		return -EINVAL;
 	}
 
-	freq_div_hz = timer_clock_freq / HZ;
-
-	ret = request_irq(irq, timer_interrupt, IRQF_TIMER, "timer",
-			  &clockevent_xilinx_timer);
-	if (ret) {
-		pr_err("Failed to setup IRQ");
-		return ret;
+	if (clocksource) {
+		if (clocksource_baseaddr) {
+			pr_err("%s: cpu %d has already clocksource timer\n",
+			       __func__, cpu_id);
+			return -EINVAL;
+		}
+
+		/* At this point we know that clocksource timer is second one */
+		clocksource_baseaddr = timer_baseaddr + TCSR1;
+		pr_info("%s: Timer base: 0x%x, Clocksource base: 0x%x\n",
+			__func__, (u32)timer_baseaddr,
+			(u32)clocksource_baseaddr);
+
+		ret = xilinx_clocksource_init(timer_clock_freq);
+		if (ret)
+			return ret;
 	}
 
-	ret = xilinx_clocksource_init();
-	if (ret)
-		return ret;
-
-	ret = xilinx_clockevent_init();
-	if (ret)
-		return ret;
+	if (clockevent) {
+		struct xilinx_timer *timer_st;
 
-	sched_clock_register(xilinx_clock_read, 32, timer_clock_freq);
+		/* Record what we know already */
+		timer_st = per_cpu_ptr(&timer_priv, cpu_id);
+		if (timer_st->timer_baseaddr) {
+			pr_err("%s: cpu %d has already clockevent timer\n",
+			       __func__, cpu_id);
+			return -EINVAL;
+		}
+
+		timer_st->timer_baseaddr = timer_baseaddr;
+
+		timer_st->irq = irq_of_parse_and_map(timer, 0);
+		if (timer_st->irq <= 0) {
+			pr_err("Failed to parse and map irq");
+			return -EINVAL;
+		}
+
+		pr_info("%pOF: irq=%d, cpu_id %d\n",
+			timer, timer_st->irq, cpu_id);
+
+		timer_st->timer_clock_freq = timer_clock_freq;
+
+		timer_st->freq_div_hz = timer_clock_freq / HZ;
+
+		/* Can't call it several times */
+		if (!initialized && !cpu_id) {
+			ret = cpuhp_setup_state(CPUHP_AP_MICROBLAZE_TIMER_STARTING,
+					"clockevents/microblaze/arch_timer:starting",
+					microblaze_timer_starting,
+					microblaze_timer_dying);
+			if (!ret)
+				initialized++;
+		}
+	}
 
-	return 0;
+	return ret;
 }
 
 TIMER_OF_DECLARE(xilinx_timer, "xlnx,xps-timer-1.00.a",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/kernel/vmlinux.lds.S
@@ -120,12 +120,6 @@
 		CON_INITCALL
 	}
 
-	__init_end_before_initramfs = .;
-
-	.init.ramfs : AT(ADDR(.init.ramfs) - LOAD_OFFSET) {
-		INIT_RAM_FS
-	}
-
 	__init_end = .;
 
 	.bss ALIGN (PAGE_SIZE) : AT(ADDR(.bss) - LOAD_OFFSET) {
@@ -138,6 +132,15 @@
 	}
 	. = ALIGN(PAGE_SIZE);
 	_end = .;
+	/* Add space in TLB mapping for early free pages mapping */
+	. = . + 0x100000; /* CONFIG_LOWMEM_SIZE >> PTE_SHIFT + space */
+
+	_end_tlb_mapping = . ;
+
+	.init.ramfs : AT(ADDR(.init.ramfs) - LOAD_OFFSET) {
+		INIT_RAM_FS
+	}
+	__initramfs_end = . ;
 
 	DISCARDS
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/lib/memcpy.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/lib/memcpy.c
@@ -31,20 +31,7 @@
 
 #include <linux/string.h>
 
-#ifdef __HAVE_ARCH_MEMCPY
-#ifndef CONFIG_OPT_LIB_FUNCTION
-void *memcpy(void *v_dst, const void *v_src, __kernel_size_t c)
-{
-	const char *src = v_src;
-	char *dst = v_dst;
-
-	/* Simple, byte oriented memcpy. */
-	while (c--)
-		*dst++ = *src++;
-
-	return v_dst;
-}
-#else /* CONFIG_OPT_LIB_FUNCTION */
+#ifdef CONFIG_OPT_LIB_FUNCTION
 void *memcpy(void *v_dst, const void *v_src, __kernel_size_t c)
 {
 	const char *src = v_src;
@@ -188,6 +175,5 @@
 
 	return v_dst;
 }
-#endif /* CONFIG_OPT_LIB_FUNCTION */
 EXPORT_SYMBOL(memcpy);
-#endif /* __HAVE_ARCH_MEMCPY */
+#endif /* CONFIG_OPT_LIB_FUNCTION */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/lib/memmove.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/lib/memmove.c
@@ -30,31 +30,7 @@
 #include <linux/compiler.h>
 #include <linux/string.h>
 
-#ifdef __HAVE_ARCH_MEMMOVE
-#ifndef CONFIG_OPT_LIB_FUNCTION
-void *memmove(void *v_dst, const void *v_src, __kernel_size_t c)
-{
-	const char *src = v_src;
-	char *dst = v_dst;
-
-	if (!c)
-		return v_dst;
-
-	/* Use memcpy when source is higher than dest */
-	if (v_dst <= v_src)
-		return memcpy(v_dst, v_src, c);
-
-	/* copy backwards, from end to beginning */
-	src += c;
-	dst += c;
-
-	/* Simple, byte oriented memmove. */
-	while (c--)
-		*--dst = *--src;
-
-	return v_dst;
-}
-#else /* CONFIG_OPT_LIB_FUNCTION */
+#ifdef CONFIG_OPT_LIB_FUNCTION
 void *memmove(void *v_dst, const void *v_src, __kernel_size_t c)
 {
 	const char *src = v_src;
@@ -215,6 +191,5 @@
 	}
 	return v_dst;
 }
-#endif /* CONFIG_OPT_LIB_FUNCTION */
 EXPORT_SYMBOL(memmove);
-#endif /* __HAVE_ARCH_MEMMOVE */
+#endif /* CONFIG_OPT_LIB_FUNCTION */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/lib/memset.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/lib/memset.c
@@ -30,22 +30,7 @@
 #include <linux/compiler.h>
 #include <linux/string.h>
 
-#ifdef __HAVE_ARCH_MEMSET
-#ifndef CONFIG_OPT_LIB_FUNCTION
-void *memset(void *v_src, int c, __kernel_size_t n)
-{
-	char *src = v_src;
-
-	/* Truncate c to 8 bits */
-	c = (c & 0xFF);
-
-	/* Simple, byte oriented memset or the rest of count. */
-	while (n--)
-		*src++ = c;
-
-	return v_src;
-}
-#else /* CONFIG_OPT_LIB_FUNCTION */
+#ifdef CONFIG_OPT_LIB_FUNCTION
 void *memset(void *v_src, int c, __kernel_size_t n)
 {
 	char *src = v_src;
@@ -89,11 +74,21 @@
 	}
 
 	/* Simple, byte oriented memset or the rest of count. */
-	while (n--)
+	switch(n) {
+	case 3:
+		*src++ = c;
+		fallthrough;
+	case 2:
 		*src++ = c;
+		fallthrough;
+	case 1:
+		*src++ = c;
+		break;
+	default:
+		break;
+	}
 
 	return v_src;
 }
-#endif /* CONFIG_OPT_LIB_FUNCTION */
 EXPORT_SYMBOL(memset);
-#endif /* __HAVE_ARCH_MEMSET */
+#endif /* CONFIG_OPT_LIB_FUNCTION */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/mm/init.c
@@ -13,6 +13,7 @@
 #include <linux/kernel.h>
 #include <linux/mm.h> /* mem_init */
 #include <linux/initrd.h>
+#include <linux/of_fdt.h>
 #include <linux/pagemap.h>
 #include <linux/pfn.h>
 #include <linux/slab.h>
@@ -191,11 +192,7 @@
 asmlinkage void __init mmu_init(void)
 {
 	unsigned int kstart, ksize;
-
-	if (!memblock.reserved.cnt) {
-		pr_emerg("Error memory count\n");
-		machine_restart(NULL);
-	}
+	phys_addr_t __maybe_unused size;
 
 	if ((u32) memblock.memory.regions[0].size < 0x400000) {
 		pr_emerg("Memory must be greater than 4MB\n");
@@ -232,10 +229,14 @@
 #if defined(CONFIG_BLK_DEV_INITRD)
 	/* Remove the init RAM disk from the available memory. */
 	if (initrd_start) {
-		unsigned long size;
 		size = initrd_end - initrd_start;
 		memblock_reserve(__virt_to_phys(initrd_start), size);
 	}
+
+	size = __initramfs_end - __initramfs_start;
+	if (size)
+		memblock_reserve((phys_addr_t)__virt_to_phys(__initramfs_start),
+				 size);
 #endif /* CONFIG_BLK_DEV_INITRD */
 
 	/* Initialize the MMU hardware */
@@ -261,8 +262,12 @@
 
 	parse_early_param();
 
+	early_init_fdt_scan_reserved_mem();
+
 	/* CMA initialization */
 	dma_contiguous_reserve(memory_start + lowmem_size - 1);
+
+	memblock_dump_all();
 }
 
 void * __ref zalloc_maybe_bootmem(size_t size, gfp_t mask)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/mm/mmu_context.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/mm/mmu_context.c
@@ -2,7 +2,11 @@
 /*
  * This file contains the routines for handling the MMU.
  *
- *    Copyright (C) 2007 Xilinx, Inc.  All rights reserved.
+ *    Copyright (C) 2007,2013-2020 Xilinx, Inc.  All rights reserved.
+ *
+ *  Derived from arch/powerpc/mm/mmu_context_nohash.c
+ *    Copyright 2008 Ben Herrenschmidt <benh@kernel.crashing.org>
+ *                IBM Corp.
  *
  *  Derived from arch/ppc/mm/4xx_mmu.c:
  *  -- paulus
@@ -19,47 +23,248 @@
  *    Copyright (C) 1991, 1992, 1993, 1994  Linus Torvalds
  */
 
+#include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/notifier.h>
+#include <linux/cpu.h>
+#include <linux/slab.h>
 
 #include <asm/tlbflush.h>
 #include <asm/mmu_context.h>
 
-mm_context_t next_mmu_context;
-unsigned long context_map[LAST_CONTEXT / BITS_PER_LONG + 1];
-atomic_t nr_free_contexts;
-struct mm_struct *context_mm[LAST_CONTEXT+1];
+static unsigned int next_context, nr_free_contexts;
+static unsigned long context_map[LAST_CONTEXT / BITS_PER_LONG + 1];
+#ifdef CONFIG_SMP
+static unsigned long stale_map[LAST_CONTEXT / BITS_PER_LONG + 1][NR_CPUS];
+#endif
+static struct mm_struct *context_mm[LAST_CONTEXT + 1];
+static DEFINE_RAW_SPINLOCK(context_lock);
 
 /*
- * Initialize the context management stuff.
+ * Steal a context from a task that has one at the moment.
+ *
+ * This is used when we are running out of available PID numbers
+ * on the processors.
+ *
+ * This isn't an LRU system, it just frees up each context in
+ * turn (sort-of pseudo-random replacement :).  This would be the
+ * place to implement an LRU scheme if anyone were motivated to do it.
+ *
+ * For context stealing, we use a slightly different approach for
+ * SMP and UP. Basically, the UP one is simpler and doesn't use
+ * the stale map as we can just flush the local CPU.
  */
-void __init mmu_context_init(void)
+#ifdef CONFIG_SMP
+static unsigned int steal_context_smp(unsigned int id)
 {
-	/*
-	 * The use of context zero is reserved for the kernel.
-	 * This code assumes FIRST_CONTEXT < 32.
+	struct mm_struct *mm;
+	unsigned int cpu, max;
+
+	max = LAST_CONTEXT - FIRST_CONTEXT;
+
+	/* Attempt to free next_context first and then loop until we manage */
+	while (max--) {
+		/* Pick up the victim mm */
+		mm = context_mm[id];
+
+		/* We have a candidate victim, check if it's active, on SMP
+		 * we cannot steal active contexts
+		 */
+		if (mm->context.active) {
+			id++;
+			if (id > LAST_CONTEXT)
+				id = FIRST_CONTEXT;
+			continue;
+		}
+
+		/* Mark this mm has having no context anymore */
+		mm->context.id = MMU_NO_CONTEXT;
+
+		/* Mark it stale on all CPUs that used this mm. */
+		for_each_cpu(cpu, mm_cpumask(mm)) {
+			__set_bit(id, stale_map[cpu]);
+		}
+		return id;
+	}
+
+	/* This will happen if you have more CPUs than available contexts,
+	 * all we can do here is wait a bit and try again
 	 */
-	context_map[0] = (1 << FIRST_CONTEXT) - 1;
-	next_mmu_context = FIRST_CONTEXT;
-	atomic_set(&nr_free_contexts, LAST_CONTEXT - FIRST_CONTEXT + 1);
+	raw_spin_unlock(&context_lock);
+	cpu_relax();
+	raw_spin_lock(&context_lock);
+
+	/* This will cause the caller to try again */
+	return MMU_NO_CONTEXT;
 }
+#endif  /* CONFIG_SMP */
 
 /*
- * Steal a context from a task that has one at the moment.
- *
- * This isn't an LRU system, it just frees up each context in
- * turn (sort-of pseudo-random replacement :).  This would be the
- * place to implement an LRU scheme if anyone were motivated to do it.
+ * Note that this will also be called on SMP if all other CPUs are
+ * offlined, which means that it may be called for cpu != 0. For
+ * this to work, we somewhat assume that CPUs that are onlined
+ * come up with a fully clean TLB (or are cleaned when offlined)
  */
-void steal_context(void)
+static unsigned int steal_context_up(unsigned int id)
 {
 	struct mm_struct *mm;
+	unsigned int cpu = smp_processor_id();
+
+	/* Pick up the victim mm */
+	mm = context_mm[id];
+
+	pr_debug("[%d] steal context %d from mm @%p\n", cpu, id, mm);
+
+	/* Flush the TLB for that context */
+	local_flush_tlb_mm(mm);
+
+	/* Mark this mm has having no context anymore */
+	mm->context.id = MMU_NO_CONTEXT;
+
+	/* TODO: This clear should ultimately be part of local_flush_tlb_mm */
+#ifdef CONFIG_SMP
+	__clear_bit(id, stale_map[cpu]);
+#endif
+
+	return id;
+}
+
+void switch_mmu_context(struct mm_struct *prev, struct mm_struct *next)
+{
+	unsigned int id;
+#ifdef CONFIG_SMP
+	unsigned int cpu = smp_processor_id();
+#endif
+	unsigned long *map;
+
+	/* No lockless fast path .. yet */
+	raw_spin_lock(&context_lock);
+
+#ifdef CONFIG_SMP
+	/* Mark us active and the previous one not anymore */
+	next->context.active++;
+	if (prev) {
+		WARN_ON(prev->context.active < 1);
+		prev->context.active--;
+	}
 
-	/* free up context `next_mmu_context' */
-	/* if we shouldn't free context 0, don't... */
-	if (next_mmu_context < FIRST_CONTEXT)
-		next_mmu_context = FIRST_CONTEXT;
-	mm = context_mm[next_mmu_context];
-	flush_tlb_mm(mm);
-	destroy_context(mm);
+ again:
+#endif /* CONFIG_SMP */
+
+	/* If we already have a valid assigned context, skip all that */
+	id = next->context.id;
+	if (likely(id != MMU_NO_CONTEXT))
+		goto ctxt_ok;
+
+	/* We really don't have a context, let's try to acquire one */
+	id = next_context;
+	if (id > LAST_CONTEXT)
+		id = FIRST_CONTEXT;
+	map = context_map;
+
+	/* No more free contexts, let's try to steal one */
+	if (nr_free_contexts == 0) {
+#ifdef CONFIG_SMP
+		if (num_online_cpus() > 1) {
+			id = steal_context_smp(id);
+			if (id == MMU_NO_CONTEXT)
+				goto again;
+			goto stolen;
+		}
+#endif /* CONFIG_SMP */
+		id = steal_context_up(id);
+		goto stolen;
+	}
+	nr_free_contexts--;
+
+	/* We know there's at least one free context, try to find it */
+	while (__test_and_set_bit(id, map)) {
+		id = find_next_zero_bit(map, LAST_CONTEXT + 1, id);
+		if (id > LAST_CONTEXT)
+			id = FIRST_CONTEXT;
+	}
+ stolen:
+	next_context = id + 1;
+	context_mm[id] = next;
+	next->context.id = id;
+
+ ctxt_ok:
+
+	/* If that context got marked stale on this CPU, then flush the
+	 * local TLB for it and unmark it before we use it
+	 */
+#ifdef CONFIG_SMP
+	if (test_bit(id, stale_map[cpu])) {
+		local_flush_tlb_mm(next);
+
+		/*
+		 * TODO: This clear should ultimately be part of
+		 * local_flush_tlb_mm
+		 */
+		__clear_bit(id, stale_map[cpu]);
+	}
+#endif
+
+	/* Flick the MMU and release lock */
+	set_context(id, next->pgd);
+	raw_spin_unlock(&context_lock);
+}
+
+/*
+ * Set up the context for a new address space.
+ */
+int init_new_context(struct task_struct *t, struct mm_struct *mm)
+{
+	mm->context.id = MMU_NO_CONTEXT;
+	mm->context.active = 0;
+
+	return 0;
+}
+
+/*
+ * We're finished using the context for an address space.
+ */
+void destroy_context(struct mm_struct *mm)
+{
+	unsigned long flags;
+	unsigned int id;
+
+	if (mm->context.id == MMU_NO_CONTEXT)
+		return;
+
+	WARN_ON(mm->context.active != 0);
+
+	raw_spin_lock_irqsave(&context_lock, flags);
+	id = mm->context.id;
+	if (id != MMU_NO_CONTEXT) {
+		__clear_bit(id, context_map);
+		mm->context.id = MMU_NO_CONTEXT;
+		mm->context.active = 0;
+		context_mm[id] = NULL;
+		nr_free_contexts++;
+	}
+	raw_spin_unlock_irqrestore(&context_lock, flags);
+}
+
+/*
+ * Initialize the context management stuff.
+ */
+void __init mmu_context_init(void)
+{
+	/*
+	 * Mark init_mm as being active on all possible CPUs since
+	 * we'll get called with prev == init_mm the first time
+	 * we schedule on a given CPU
+	 */
+	init_mm.context.active = NR_CPUS;
+
+	/*
+	 * The use of context zero is reserved for the kernel.
+	 * This code assumes FIRST_CONTEXT < 32.
+	 */
+	context_map[0] = (1 << FIRST_CONTEXT) - 1;
+	next_context = FIRST_CONTEXT;
+	nr_free_contexts = LAST_CONTEXT - FIRST_CONTEXT + 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/microblaze/pci/pci-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/microblaze/pci/pci-common.c
@@ -141,7 +141,7 @@
 	return NULL;
 }
 
-void pcibios_set_master(struct pci_dev *dev)
+void __weak pcibios_set_master(struct pci_dev *dev)
 {
 	/* No special bus mastering setup handling */
 }
@@ -553,37 +553,7 @@
  */
 static void pcibios_fixup_resources(struct pci_dev *dev)
 {
-	struct pci_controller *hose = pci_bus_to_host(dev->bus);
-	int i;
-
-	if (!hose) {
-		pr_err("No host bridge for PCI dev %s !\n",
-		       pci_name(dev));
-		return;
-	}
-	for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
-		struct resource *res = dev->resource + i;
-		if (!res->flags)
-			continue;
-		if (res->start == 0) {
-			pr_debug("PCI:%s Resource %d %016llx-%016llx [%x]",
-				 pci_name(dev), i,
-				 (unsigned long long)res->start,
-				 (unsigned long long)res->end,
-				 (unsigned int)res->flags);
-			pr_debug("is unassigned\n");
-			res->end -= res->start;
-			res->start = 0;
-			res->flags |= IORESOURCE_UNSET;
-			continue;
-		}
 
-		pr_debug("PCI:%s Resource %d %016llx-%016llx [%x]\n",
-			 pci_name(dev), i,
-			 (unsigned long long)res->start,
-			 (unsigned long long)res->end,
-			 (unsigned int)res->flags);
-	}
 }
 DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pcibios_fixup_resources);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/Kbuild.platforms
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/Kbuild.platforms
@@ -38,4 +38,4 @@
 platform-$(CONFIG_MACH_VR41XX)		+= vr41xx/
 
 # include the platform specific files
-include $(patsubst %, $(srctree)/arch/mips/%/Platform, $(platform-y))
+include $(patsubst %/, $(srctree)/arch/mips/%/Platform, $(platform-y))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/Kconfig
@@ -4,6 +4,7 @@
 	default y
 	select ARCH_32BIT_OFF_T if !64BIT
 	select ARCH_BINFMT_ELF_STATE if MIPS_FP_SUPPORT
+	select ARCH_HAS_CPU_FINALIZE_INIT
 	select ARCH_HAS_DEBUG_VIRTUAL if !64BIT
 	select ARCH_HAS_FORTIFY_SOURCE
 	select ARCH_HAS_KCOV
@@ -81,6 +82,7 @@
 	select HAVE_LD_DEAD_CODE_DATA_ELIMINATION
 	select HAVE_MOD_ARCH_SPECIFIC
 	select HAVE_NMI
+	select HAVE_PATA_PLATFORM
 	select HAVE_PERF_EVENTS
 	select HAVE_PERF_REGS
 	select HAVE_PERF_USER_STACK_DUMP
@@ -332,6 +334,9 @@
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
+	select SYS_HAS_CPU_BMIPS32_3300
+	select SYS_HAS_CPU_BMIPS4350
+	select SYS_HAS_CPU_BMIPS4380
 	select SWAP_IO_SPACE
 	select GPIOLIB
 	select MIPS_L1_CACHE_SHIFT_4
@@ -475,6 +480,7 @@
 
 config MACH_LOONGSON64
 	bool "Loongson 64-bit family of machines"
+	select ARCH_DMA_DEFAULT_COHERENT
 	select ARCH_SPARSEMEM_ENABLE
 	select ARCH_MIGHT_HAVE_PC_PARPORT
 	select ARCH_MIGHT_HAVE_PC_SERIO
@@ -1374,11 +1380,13 @@
 	select CPU_SUPPORTS_MSA
 	select CPU_DIEI_BROKEN if !LOONGSON3_ENHANCEMENT
 	select CPU_MIPSR2_IRQ_VI
+	select DMA_NONCOHERENT
 	select WEAK_ORDERING
 	select WEAK_REORDERING_BEYOND_LLSC
 	select MIPS_ASID_BITS_VARIABLE
 	select MIPS_PGD_C0_CONTEXT
 	select MIPS_L1_CACHE_SHIFT_6
+	select MIPS_FP_SUPPORT
 	select GPIOLIB
 	select SWIOTLB
 	select HAVE_KVM
@@ -1989,6 +1997,10 @@
 config SYS_HAS_CPU_MIPS64_R2
 	bool
 
+config SYS_HAS_CPU_MIPS64_R5
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
 config SYS_HAS_CPU_MIPS64_R6
 	bool
 	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
@@ -2153,7 +2165,7 @@
 	bool
 config CPU_SUPPORTS_HUGEPAGES
 	bool
-	depends on !(32BIT && (ARCH_PHYS_ADDR_T_64BIT || EVA))
+	depends on !(32BIT && (PHYS_ADDR_T_64BIT || EVA))
 config MIPS_PGD_C0_CONTEXT
 	bool
 	depends on 64BIT
@@ -3185,7 +3197,7 @@
 config PGTABLE_LEVELS
 	int
 	default 4 if PAGE_SIZE_4KB && MIPS_VA_BITS_48
-	default 3 if 64BIT && !PAGE_SIZE_64KB
+	default 3 if 64BIT && (!PAGE_SIZE_64KB || MIPS_VA_BITS_48)
 	default 2
 
 config MIPS_AUTO_PFN_OFFSET
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/Makefile
@@ -254,7 +254,9 @@
 #
 # Board-dependent options and extra files
 #
+ifdef need-compiler
 include $(srctree)/arch/mips/Kbuild.platforms
+endif
 
 ifdef CONFIG_PHYSICAL_START
 load-y					= $(CONFIG_PHYSICAL_START)
@@ -273,12 +275,12 @@
 ifdef CONFIG_64BIT
   ifndef KBUILD_SYM32
     ifeq ($(shell expr $(load-y) \< 0xffffffff80000000), 0)
-      KBUILD_SYM32 = y
+      KBUILD_SYM32 = $(call cc-option-yn, -msym32)
     endif
   endif
 
-  ifeq ($(KBUILD_SYM32)$(call cc-option-yn,-msym32), yy)
-    cflags-y += -msym32 -DKBUILD_64BIT_SYM32
+  ifeq ($(KBUILD_SYM32), y)
+    cflags-$(KBUILD_SYM32) += -msym32 -DKBUILD_64BIT_SYM32
   else
     ifeq ($(CONFIG_CPU_DADDI_WORKAROUNDS), y)
       $(error CONFIG_CPU_DADDI_WORKAROUNDS unsupported without -msym32)
@@ -319,9 +321,9 @@
 
 KBUILD_LDFLAGS		+= -m $(ld-emul)
 
-ifdef CONFIG_MIPS
+ifdef need-compiler
 CHECKFLAGS += $(shell $(CC) $(KBUILD_CFLAGS) -dM -E -x c /dev/null | \
-	egrep -vw '__GNUC_(MINOR_|PATCHLEVEL_)?_' | \
+	grep -E -vw '__GNUC_(MINOR_|PATCHLEVEL_)?_' | \
 	sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/" -e 's/\$$/&&/g')
 endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/alchemy/common/dbdma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/alchemy/common/dbdma.c
@@ -30,6 +30,7 @@
  *
  */
 
+#include <linux/dma-map-ops.h> /* for dma_default_coherent */
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/slab.h>
@@ -623,17 +624,18 @@
 		dp->dscr_cmd0 &= ~DSCR_CMD0_IE;
 
 	/*
-	 * There is an errata on the Au1200/Au1550 parts that could result
-	 * in "stale" data being DMA'ed. It has to do with the snoop logic on
-	 * the cache eviction buffer.  DMA_NONCOHERENT is on by default for
-	 * these parts. If it is fixed in the future, these dma_cache_inv will
-	 * just be nothing more than empty macros. See io.h.
+	 * There is an erratum on certain Au1200/Au1550 revisions that could
+	 * result in "stale" data being DMA'ed. It has to do with the snoop
+	 * logic on the cache eviction buffer.  dma_default_coherent is set
+	 * to false on these parts.
 	 */
-	dma_cache_wback_inv((unsigned long)buf, nbytes);
+	if (!dma_default_coherent)
+		dma_cache_wback_inv(KSEG0ADDR(buf), nbytes);
 	dp->dscr_cmd0 |= DSCR_CMD0_V;	/* Let it rip */
 	wmb(); /* drain writebuffer */
 	dma_cache_wback_inv((unsigned long)dp, sizeof(*dp));
 	ctp->chan_ptr->ddma_dbell = 0;
+	wmb(); /* force doorbell write out to dma engine */
 
 	/* Get next descriptor pointer. */
 	ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
@@ -685,17 +687,18 @@
 			  dp->dscr_source1, dp->dscr_dest0, dp->dscr_dest1);
 #endif
 	/*
-	 * There is an errata on the Au1200/Au1550 parts that could result in
-	 * "stale" data being DMA'ed. It has to do with the snoop logic on the
-	 * cache eviction buffer.  DMA_NONCOHERENT is on by default for these
-	 * parts. If it is fixed in the future, these dma_cache_inv will just
-	 * be nothing more than empty macros. See io.h.
+	 * There is an erratum on certain Au1200/Au1550 revisions that could
+	 * result in "stale" data being DMA'ed. It has to do with the snoop
+	 * logic on the cache eviction buffer.  dma_default_coherent is set
+	 * to false on these parts.
 	 */
-	dma_cache_inv((unsigned long)buf, nbytes);
+	if (!dma_default_coherent)
+		dma_cache_inv(KSEG0ADDR(buf), nbytes);
 	dp->dscr_cmd0 |= DSCR_CMD0_V;	/* Let it rip */
 	wmb(); /* drain writebuffer */
 	dma_cache_wback_inv((unsigned long)dp, sizeof(*dp));
 	ctp->chan_ptr->ddma_dbell = 0;
+	wmb(); /* force doorbell write out to dma engine */
 
 	/* Get next descriptor pointer. */
 	ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/alchemy/devboards/db1000.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/alchemy/devboards/db1000.c
@@ -14,7 +14,6 @@
 #include <linux/interrupt.h>
 #include <linux/leds.h>
 #include <linux/mmc/host.h>
-#include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/spi/spi.h>
@@ -165,14 +164,10 @@
 
 /******************************************************************************/
 
+#ifdef CONFIG_MMC_AU1X
 static irqreturn_t db1100_mmc_cd(int irq, void *ptr)
 {
-	void (*mmc_cd)(struct mmc_host *, unsigned long);
-	/* link against CONFIG_MMC=m */
-	mmc_cd = symbol_get(mmc_detect_change);
-	mmc_cd(ptr, msecs_to_jiffies(500));
-	symbol_put(mmc_detect_change);
-
+	mmc_detect_change(ptr, msecs_to_jiffies(500));
 	return IRQ_HANDLED;
 }
 
@@ -375,6 +370,7 @@
 	.num_resources	= ARRAY_SIZE(au1100_mmc1_res),
 	.resource	= au1100_mmc1_res,
 };
+#endif /* CONFIG_MMC_AU1X */
 
 /******************************************************************************/
 
@@ -438,8 +434,10 @@
 
 static struct platform_device *db1100_devs[] = {
 	&au1100_lcd_device,
+#ifdef CONFIG_MMC_AU1X
 	&db1100_mmc0_dev,
 	&db1100_mmc1_dev,
+#endif
 };
 
 int __init db1000_dev_setup(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/alchemy/devboards/db1200.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/alchemy/devboards/db1200.c
@@ -10,7 +10,6 @@
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
-#include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/leds.h>
@@ -327,6 +326,7 @@
 
 /**********************************************************************/
 
+#ifdef CONFIG_MMC_AU1X
 /* SD carddetects:  they're supposed to be edge-triggered, but ack
  * doesn't seem to work (CPLD Rev 2).  Instead, the screaming one
  * is disabled and its counterpart enabled.  The 200ms timeout is
@@ -340,14 +340,7 @@
 
 static irqreturn_t db1200_mmc_cdfn(int irq, void *ptr)
 {
-	void (*mmc_cd)(struct mmc_host *, unsigned long);
-
-	/* link against CONFIG_MMC=m */
-	mmc_cd = symbol_get(mmc_detect_change);
-	if (mmc_cd) {
-		mmc_cd(ptr, msecs_to_jiffies(200));
-		symbol_put(mmc_detect_change);
-	}
+	mmc_detect_change(ptr, msecs_to_jiffies(200));
 
 	msleep(100);	/* debounce */
 	if (irq == DB1200_SD0_INSERT_INT)
@@ -431,14 +424,7 @@
 
 static irqreturn_t pb1200_mmc1_cdfn(int irq, void *ptr)
 {
-	void (*mmc_cd)(struct mmc_host *, unsigned long);
-
-	/* link against CONFIG_MMC=m */
-	mmc_cd = symbol_get(mmc_detect_change);
-	if (mmc_cd) {
-		mmc_cd(ptr, msecs_to_jiffies(200));
-		symbol_put(mmc_detect_change);
-	}
+	mmc_detect_change(ptr, msecs_to_jiffies(200));
 
 	msleep(100);	/* debounce */
 	if (irq == PB1200_SD1_INSERT_INT)
@@ -599,6 +585,7 @@
 	.num_resources	= ARRAY_SIZE(au1200_mmc1_res),
 	.resource	= au1200_mmc1_res,
 };
+#endif /* CONFIG_MMC_AU1X */
 
 /**********************************************************************/
 
@@ -766,7 +753,9 @@
 static struct platform_device *db1200_devs[] __initdata = {
 	NULL,		/* PSC0, selected by S6.8 */
 	&db1200_ide_dev,
+#ifdef CONFIG_MMC_AU1X
 	&db1200_mmc0_dev,
+#endif
 	&au1200_lcd_dev,
 	&db1200_eth_dev,
 	&db1200_nand_dev,
@@ -777,7 +766,9 @@
 };
 
 static struct platform_device *pb1200_devs[] __initdata = {
+#ifdef CONFIG_MMC_AU1X
 	&pb1200_mmc1_dev,
+#endif
 };
 
 /* Some peripheral base addresses differ on the PB1200 */
@@ -856,7 +847,7 @@
 	i2c_register_board_info(0, db1200_i2c_devs,
 				ARRAY_SIZE(db1200_i2c_devs));
 	spi_register_board_info(db1200_spi_devs,
-				ARRAY_SIZE(db1200_i2c_devs));
+				ARRAY_SIZE(db1200_spi_devs));
 
 	/* SWITCHES:	S6.8 I2C/SPI selector  (OFF=I2C	 ON=SPI)
 	 *		S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/alchemy/devboards/db1300.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/alchemy/devboards/db1300.c
@@ -17,7 +17,6 @@
 #include <linux/interrupt.h>
 #include <linux/ata_platform.h>
 #include <linux/mmc/host.h>
-#include <linux/module.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/platnand.h>
 #include <linux/platform_device.h>
@@ -451,6 +450,7 @@
 
 /**********************************************************************/
 
+#ifdef CONFIG_MMC_AU1X
 static irqreturn_t db1300_mmc_cd(int irq, void *ptr)
 {
 	disable_irq_nosync(irq);
@@ -459,14 +459,7 @@
 
 static irqreturn_t db1300_mmc_cdfn(int irq, void *ptr)
 {
-	void (*mmc_cd)(struct mmc_host *, unsigned long);
-
-	/* link against CONFIG_MMC=m.  We can only be called once MMC core has
-	 * initialized the controller, so symbol_get() should always succeed.
-	 */
-	mmc_cd = symbol_get(mmc_detect_change);
-	mmc_cd(ptr, msecs_to_jiffies(200));
-	symbol_put(mmc_detect_change);
+	mmc_detect_change(ptr, msecs_to_jiffies(200));
 
 	msleep(100);	/* debounce */
 	if (irq == DB1300_SD1_INSERT_INT)
@@ -640,6 +633,7 @@
 	.resource	= au1300_sd0_res,
 	.num_resources	= ARRAY_SIZE(au1300_sd0_res),
 };
+#endif /* CONFIG_MMC_AU1X */
 
 /**********************************************************************/
 
@@ -784,8 +778,10 @@
 	&db1300_5waysw_dev,
 	&db1300_nand_dev,
 	&db1300_ide_dev,
+#ifdef CONFIG_MMC_AU1X
 	&db1300_sd0_dev,
 	&db1300_sd1_dev,
+#endif
 	&db1300_lcd_dev,
 	&db1300_ac97_dev,
 	&db1300_i2s_dev,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/alchemy/devboards/db1550.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/alchemy/devboards/db1550.c
@@ -588,7 +588,7 @@
 	i2c_register_board_info(0, db1550_i2c_devs,
 				ARRAY_SIZE(db1550_i2c_devs));
 	spi_register_board_info(db1550_spi_devs,
-				ARRAY_SIZE(db1550_i2c_devs));
+				ARRAY_SIZE(db1550_spi_devs));
 
 	c = clk_get(NULL, "psc0_intclk");
 	if (!IS_ERR(c)) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/bcm47xx/prom.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/bcm47xx/prom.c
@@ -86,7 +86,7 @@
 			pr_debug("Assume 128MB RAM\n");
 			break;
 		}
-		if (!memcmp(prom_init, prom_init + mem, 32))
+		if (!memcmp((void *)prom_init, (void *)prom_init + mem, 32))
 			break;
 	}
 	lowmem = mem;
@@ -159,7 +159,7 @@
 
 	off = EXTVBASE + __pa(off);
 	for (extmem = 128 << 20; extmem < 512 << 20; extmem <<= 1) {
-		if (!memcmp(prom_init, (void *)(off + extmem), 16))
+		if (!memcmp((void *)prom_init, (void *)(off + extmem), 16))
 			break;
 	}
 	extmem -= lowmem;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/bcm63xx/clk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/bcm63xx/clk.c
@@ -361,6 +361,8 @@
  */
 int clk_enable(struct clk *clk)
 {
+	if (!clk)
+		return 0;
 	mutex_lock(&clocks_mutex);
 	clk_enable_unlocked(clk);
 	mutex_unlock(&clocks_mutex);
@@ -381,6 +383,18 @@
 
 EXPORT_SYMBOL(clk_disable);
 
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return NULL;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
 unsigned long clk_get_rate(struct clk *clk)
 {
 	if (!clk)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/bmips/dma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/bmips/dma.c
@@ -64,6 +64,8 @@
 	return dma_addr;
 }
 
+bool bmips_rac_flush_disable;
+
 void arch_sync_dma_for_cpu_all(void)
 {
 	void __iomem *cbr = BMIPS_GET_CBR();
@@ -74,6 +76,9 @@
 	    boot_cpu_type() != CPU_BMIPS4380)
 		return;
 
+	if (unlikely(bmips_rac_flush_disable))
+		return;
+
 	/* Flush stale data out of the readahead cache */
 	cfg = __raw_readl(cbr + BMIPS_RAC_CONFIG);
 	__raw_writel(cfg | 0x100, cbr + BMIPS_RAC_CONFIG);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/bmips/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/bmips/setup.c
@@ -34,6 +34,8 @@
 #define REG_BCM6328_OTP		((void __iomem *)CKSEG1ADDR(0x1000062c))
 #define BCM6328_TP1_DISABLED	BIT(9)
 
+extern bool bmips_rac_flush_disable;
+
 static const unsigned long kbase = VMLINUX_LOAD_ADDRESS & 0xfff00000;
 
 struct bmips_quirk {
@@ -103,6 +105,13 @@
 	 * disable SMP for now
 	 */
 	bmips_smp_enabled = 0;
+
+	/*
+	 * RAC flush causes kernel panics on BCM6358 when booting from TP1
+	 * because the bootloader is not initializing it properly.
+	 */
+	bmips_rac_flush_disable = !!(read_c0_brcm_cmt_local() & (1 << 31)) ||
+				  !!BMIPS_GET_CBR();
 }
 
 static void bcm6368_quirks(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/compressed/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/compressed/Makefile
@@ -56,6 +56,8 @@
 
 vmlinuzobjs-$(CONFIG_KERNEL_XZ) += $(obj)/ashldi3.o
 
+vmlinuzobjs-$(CONFIG_KERNEL_ZSTD) += $(obj)/bswapdi.o $(obj)/ashldi3.o $(obj)/clz_ctz.o
+
 extra-y += ashldi3.c
 $(obj)/ashldi3.c: $(obj)/%.c: $(srctree)/lib/%.c FORCE
 	$(call if_changed,shipped)
@@ -64,6 +66,10 @@
 $(obj)/bswapsi.c: $(obj)/%.c: $(srctree)/arch/mips/lib/%.c FORCE
 	$(call if_changed,shipped)
 
+extra-y += bswapdi.c
+$(obj)/bswapdi.c: $(obj)/%.c: $(srctree)/arch/mips/lib/%.c FORCE
+	$(call if_changed,shipped)
+
 targets := $(notdir $(vmlinuzobjs-y))
 
 targets += vmlinux.bin
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/compressed/clz_ctz.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/compressed/clz_ctz.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../../../lib/clz_ctz.c"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/dts/ingenic/ci20.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/dts/ingenic/ci20.dts
@@ -99,7 +99,7 @@
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 
-		gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
+		gpio = <&gpf 15 GPIO_ACTIVE_LOW>;
 		enable-active-high;
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -450,7 +450,7 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			eth0_addr: eth-mac-addr@0x22 {
+			eth0_addr: eth-mac-addr@22 {
 				reg = <0x22 0x6>;
 			};
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
@@ -23,14 +23,6 @@
 		};
 	};
 
-	memory@200000 {
-		compatible = "memory";
-		device_type = "memory";
-		reg = <0x00000000 0x00200000 0x00000000 0x0ee00000>, /* 238 MB at 2 MB */
-			<0x00000000 0x20000000 0x00000000 0x1f000000>, /* 496 MB at 512 MB */
-			<0x00000001 0x10000000 0x00000001 0xb0000000>; /* 6912 MB at 4352MB */
-	};
-
 	cpu_clk: cpu_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
@@ -92,12 +84,19 @@
 						<0x00000000>; /* int3 */
 		};
 
+		rtc0: rtc@1fe07800 {
+			compatible = "loongson,ls2k1000-rtc";
+			reg = <0 0x1fe07800 0 0x78>;
+			interrupt-parent = <&liointc1>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		uart0: serial@1fe00000 {
 			compatible = "ns16550a";
 			reg = <0 0x1fe00000 0 0x8>;
 			clock-frequency = <125000000>;
 			interrupt-parent = <&liointc0>;
-			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 			no-loopback-test;
 		};
 
@@ -106,7 +105,6 @@
 			device_type = "pci";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <2>;
 
 			reg = <0 0x1a000000 0 0x02000000>,
 				<0xfe 0x00000000 0 0x20000000>;
@@ -118,15 +116,15 @@
 				compatible = "pci0014,7a03.0",
 						   "pci0014,7a03",
 						   "pciclass0c0320",
-						   "pciclass0c03",
-						   "loongson, pci-gmac";
+						   "pciclass0c03";
 
 				reg = <0x1800 0x0 0x0 0x0 0x0>;
-				interrupts = <12 IRQ_TYPE_LEVEL_LOW>,
-					     <13 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <12 IRQ_TYPE_LEVEL_HIGH>,
+					     <13 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "macirq", "eth_lpi";
 				interrupt-parent = <&liointc0>;
-				phy-mode = "rgmii";
+				phy-mode = "rgmii-id";
+				phy-handle = <&phy1>;
 				mdio {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -145,11 +143,12 @@
 						   "loongson, pci-gmac";
 
 				reg = <0x1900 0x0 0x0 0x0 0x0>;
-				interrupts = <14 IRQ_TYPE_LEVEL_LOW>,
-					     <15 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
+					     <15 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "macirq", "eth_lpi";
 				interrupt-parent = <&liointc0>;
-				phy-mode = "rgmii";
+				phy-mode = "rgmii-id";
+				phy-handle = <&phy1>;
 				mdio {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -167,7 +166,7 @@
 						   "pciclass0c03";
 
 				reg = <0x2100 0x0 0x0 0x0 0x0>;
-				interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 			};
 
@@ -178,7 +177,7 @@
 						   "pciclass0c03";
 
 				reg = <0x2200 0x0 0x0 0x0 0x0>;
-				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 			};
 
@@ -189,97 +188,121 @@
 						   "pciclass0106";
 
 				reg = <0x4000 0x0 0x0 0x0 0x0>;
-				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc0>;
 			};
 
-			pci_bridge@9,0 {
+			pcie@9,0 {
 				compatible = "pci0014,7a19.0",
 						   "pci0014,7a19",
 						   "pciclass060400",
 						   "pciclass0604";
 
 				reg = <0x4800 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
-				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &liointc1 0 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-map = <0 0 0 0 &liointc1 0 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 				external-facing;
 			};
 
-			pci_bridge@a,0 {
+			pcie@a,0 {
 				compatible = "pci0014,7a09.0",
 						   "pci0014,7a09",
 						   "pciclass060400",
 						   "pciclass0604";
 
 				reg = <0x5000 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
-				interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &liointc1 1 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-map = <0 0 0 0 &liointc1 1 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 				external-facing;
 			};
 
-			pci_bridge@b,0 {
+			pcie@b,0 {
 				compatible = "pci0014,7a09.0",
 						   "pci0014,7a09",
 						   "pciclass060400",
 						   "pciclass0604";
 
 				reg = <0x5800 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
-				interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &liointc1 2 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-map = <0 0 0 0 &liointc1 2 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 				external-facing;
 			};
 
-			pci_bridge@c,0 {
+			pcie@c,0 {
 				compatible = "pci0014,7a09.0",
 						   "pci0014,7a09",
 						   "pciclass060400",
 						   "pciclass0604";
 
 				reg = <0x6000 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
-				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &liointc1 3 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-map = <0 0 0 0 &liointc1 3 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 				external-facing;
 			};
 
-			pci_bridge@d,0 {
+			pcie@d,0 {
 				compatible = "pci0014,7a19.0",
 						   "pci0014,7a19",
 						   "pciclass060400",
 						   "pciclass0604";
 
 				reg = <0x6800 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
-				interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &liointc1 4 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-map = <0 0 0 0 &liointc1 4 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 				external-facing;
 			};
 
-			pci_bridge@e,0 {
+			pcie@e,0 {
 				compatible = "pci0014,7a09.0",
 						   "pci0014,7a09",
 						   "pciclass060400",
 						   "pciclass0604";
 
 				reg = <0x7000 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
-				interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&liointc1>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &liointc1 5 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-map = <0 0 0 0 &liointc1 5 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 				external-facing;
 			};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts
@@ -33,6 +33,7 @@
 		compatible = "loongson,pch-msi-1.0";
 		reg = <0 0x2ff00000 0 0x8>;
 		interrupt-controller;
+		#interrupt-cells = <1>;
 		msi-controller;
 		loongson,msi-base-vec = <64>;
 		loongson,msi-num-vecs = <192>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/boot/dts/loongson/ls7a-pch.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/boot/dts/loongson/ls7a-pch.dtsi
@@ -63,7 +63,6 @@
 			device_type = "pci";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <2>;
 			msi-parent = <&msi>;
 
 			reg = <0 0x1a000000 0 0x02000000>,
@@ -186,8 +185,7 @@
 				compatible = "pci0014,7a03.0",
 						   "pci0014,7a03",
 						   "pciclass020000",
-						   "pciclass0200",
-						   "loongson, pci-gmac";
+						   "pciclass0200";
 
 				reg = <0x1800 0x0 0x0 0x0 0x0>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH>,
@@ -228,7 +226,7 @@
 				};
 			};
 
-			pci_bridge@9,0 {
+			pcie@9,0 {
 				compatible = "pci0014,7a19.1",
 						   "pci0014,7a19",
 						   "pciclass060400",
@@ -238,12 +236,16 @@
 				interrupts = <32 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 32 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@a,0 {
+			pcie@a,0 {
 				compatible = "pci0014,7a09.1",
 						   "pci0014,7a09",
 						   "pciclass060400",
@@ -253,12 +255,16 @@
 				interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 33 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@b,0 {
+			pcie@b,0 {
 				compatible = "pci0014,7a09.1",
 						   "pci0014,7a09",
 						   "pciclass060400",
@@ -268,12 +274,16 @@
 				interrupts = <34 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 34 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@c,0 {
+			pcie@c,0 {
 				compatible = "pci0014,7a09.1",
 						   "pci0014,7a09",
 						   "pciclass060400",
@@ -283,12 +293,16 @@
 				interrupts = <35 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 35 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@d,0 {
+			pcie@d,0 {
 				compatible = "pci0014,7a19.1",
 						   "pci0014,7a19",
 						   "pciclass060400",
@@ -298,12 +312,16 @@
 				interrupts = <36 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 36 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@e,0 {
+			pcie@e,0 {
 				compatible = "pci0014,7a09.1",
 						   "pci0014,7a09",
 						   "pciclass060400",
@@ -313,12 +331,16 @@
 				interrupts = <37 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 37 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@f,0 {
+			pcie@f,0 {
 				compatible = "pci0014,7a29.1",
 						   "pci0014,7a29",
 						   "pciclass060400",
@@ -328,12 +350,16 @@
 				interrupts = <40 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 40 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@10,0 {
+			pcie@10,0 {
 				compatible = "pci0014,7a19.1",
 						   "pci0014,7a19",
 						   "pciclass060400",
@@ -343,12 +369,16 @@
 				interrupts = <41 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 41 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@11,0 {
+			pcie@11,0 {
 				compatible = "pci0014,7a29.1",
 						   "pci0014,7a29",
 						   "pciclass060400",
@@ -358,12 +388,16 @@
 				interrupts = <42 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 42 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@12,0 {
+			pcie@12,0 {
 				compatible = "pci0014,7a19.1",
 						   "pci0014,7a19",
 						   "pciclass060400",
@@ -373,12 +407,16 @@
 				interrupts = <43 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 43 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@13,0 {
+			pcie@13,0 {
 				compatible = "pci0014,7a29.1",
 						   "pci0014,7a29",
 						   "pciclass060400",
@@ -388,12 +426,16 @@
 				interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 38 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 
-			pci_bridge@14,0 {
+			pcie@14,0 {
 				compatible = "pci0014,7a19.1",
 						   "pci0014,7a19",
 						   "pciclass060400",
@@ -403,9 +445,13 @@
 				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&pic>;
 
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
 				#interrupt-cells = <1>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &pic 39 IRQ_TYPE_LEVEL_HIGH>;
+				ranges;
 			};
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
@@ -211,7 +211,7 @@
 {
 	union cvmx_helper_link_info result;
 
-	WARN(!octeon_is_simulation(),
+	WARN_ONCE(!octeon_is_simulation(),
 	     "Using deprecated link status - please update your DT");
 
 	/* Unless we fix it later, all links are defaulted to down */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/cavium-octeon/executive/cvmx-helper.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/cavium-octeon/executive/cvmx-helper.c
@@ -1100,7 +1100,7 @@
 		if (index == 0)
 			result = __cvmx_helper_rgmii_link_get(ipd_port);
 		else {
-			WARN(1, "Using deprecated link status - please update your DT");
+			WARN_ONCE(1, "Using deprecated link status - please update your DT");
 			result.s.full_duplex = 1;
 			result.s.link_up = 1;
 			result.s.speed = 1000;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/cavium-octeon/octeon-irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/cavium-octeon/octeon-irq.c
@@ -127,6 +127,16 @@
 static int octeon_irq_force_ciu_mapping(struct irq_domain *domain,
 					int irq, int line, int bit)
 {
+	struct device_node *of_node;
+	int ret;
+
+	of_node = irq_domain_get_of_node(domain);
+	if (!of_node)
+		return -EINVAL;
+	ret = irq_alloc_desc_at(irq, of_node_to_nid(of_node));
+	if (ret < 0)
+		return ret;
+
 	return irq_domain_associate(domain, irq, line << 6 | bit);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/cavium-octeon/octeon-memcpy.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/cavium-octeon/octeon-memcpy.S
@@ -74,7 +74,7 @@
 #define EXC(inst_reg,addr,handler)		\
 9:	inst_reg, addr;				\
 	.section __ex_table,"a";		\
-	PTR	9b, handler;			\
+	PTR_WD	9b, handler;			\
 	.previous
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/cavium-octeon/octeon-platform.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/cavium-octeon/octeon-platform.c
@@ -86,11 +86,12 @@
 					 "refclk-frequency", &clock_rate);
 		if (i) {
 			dev_err(dev, "No UCTL \"refclk-frequency\"\n");
+			of_node_put(uctl_node);
 			goto exit;
 		}
 		i = of_property_read_string(uctl_node,
 					    "refclk-type", &clock_type);
-
+		of_node_put(uctl_node);
 		if (!i && strcmp("crystal", clock_type) == 0)
 			is_crystal_clock = true;
 	}
@@ -328,6 +329,7 @@
 
 	pd->dev.platform_data = &octeon_ehci_pdata;
 	octeon_ehci_hw_start(&pd->dev);
+	put_device(&pd->dev);
 
 	return ret;
 }
@@ -391,6 +393,7 @@
 
 	pd->dev.platform_data = &octeon_ohci_pdata;
 	octeon_ohci_hw_start(&pd->dev);
+	put_device(&pd->dev);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/cavium-octeon/octeon-usb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/cavium-octeon/octeon-usb.c
@@ -537,6 +537,7 @@
 			devm_iounmap(&pdev->dev, base);
 			devm_release_mem_region(&pdev->dev, res->start,
 						resource_size(res));
+			put_device(&pdev->dev);
 		}
 	} while (node != NULL);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/decstation_64_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/decstation_64_defconfig
@@ -53,8 +53,6 @@
 CONFIG_NETWORK_SECMARK=y
 CONFIG_IP_SCTP=m
 CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
-CONFIG_DECNET_ROUTER=y
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 # CONFIG_FW_LOADER is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/decstation_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/decstation_defconfig
@@ -49,8 +49,6 @@
 CONFIG_NETWORK_SECMARK=y
 CONFIG_IP_SCTP=m
 CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
-CONFIG_DECNET_ROUTER=y
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 # CONFIG_FW_LOADER is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/decstation_r4k_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/decstation_r4k_defconfig
@@ -48,8 +48,6 @@
 CONFIG_NETWORK_SECMARK=y
 CONFIG_IP_SCTP=m
 CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
-CONFIG_DECNET_ROUTER=y
 # CONFIG_WIRELESS is not set
 # CONFIG_UEVENT_HELPER is not set
 # CONFIG_FW_LOADER is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/fuloong2e_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/fuloong2e_defconfig
@@ -206,7 +206,6 @@
 CONFIG_NFSD_V4=y
 CONFIG_CIFS=m
 CONFIG_CIFS_STATS2=y
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_CIFS_DEBUG2=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/gpr_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/gpr_defconfig
@@ -69,7 +69,6 @@
 CONFIG_IP_NF_ARPTABLES=m
 CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
-CONFIG_DECNET_NF_GRABULATOR=m
 CONFIG_BRIDGE_NF_EBTABLES=m
 CONFIG_BRIDGE_EBT_BROUTE=m
 CONFIG_BRIDGE_EBT_T_FILTER=m
@@ -99,7 +98,6 @@
 CONFIG_ATM_BR2684=m
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
 CONFIG_LLC2=m
 CONFIG_ATALK=m
 CONFIG_DEV_APPLETALK=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/malta_qemu_32r6_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/malta_qemu_32r6_defconfig
@@ -165,7 +165,6 @@
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/maltaaprp_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/maltaaprp_defconfig
@@ -166,7 +166,6 @@
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/maltasmvp_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/maltasmvp_defconfig
@@ -167,7 +167,6 @@
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/maltasmvp_eva_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/maltasmvp_eva_defconfig
@@ -169,7 +169,6 @@
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/maltaup_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/maltaup_defconfig
@@ -165,7 +165,6 @@
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/mtx1_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/mtx1_defconfig
@@ -116,7 +116,6 @@
 CONFIG_IP6_NF_TARGET_REJECT=m
 CONFIG_IP6_NF_MANGLE=m
 CONFIG_IP6_NF_RAW=m
-CONFIG_DECNET_NF_GRABULATOR=m
 CONFIG_BRIDGE_NF_EBTABLES=m
 CONFIG_BRIDGE_EBT_BROUTE=m
 CONFIG_BRIDGE_EBT_T_FILTER=m
@@ -146,7 +145,6 @@
 CONFIG_ATM_BR2684=m
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
 CONFIG_LLC2=m
 CONFIG_ATALK=m
 CONFIG_DEV_APPLETALK=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/nlm_xlp_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/nlm_xlp_defconfig
@@ -200,7 +200,6 @@
 CONFIG_IP6_NF_MANGLE=m
 CONFIG_IP6_NF_RAW=m
 CONFIG_IP6_NF_SECURITY=m
-CONFIG_DECNET_NF_GRABULATOR=m
 CONFIG_BRIDGE_NF_EBTABLES=m
 CONFIG_BRIDGE_EBT_BROUTE=m
 CONFIG_BRIDGE_EBT_T_FILTER=m
@@ -234,7 +233,6 @@
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
 CONFIG_VLAN_8021Q_GVRP=y
-CONFIG_DECNET=m
 CONFIG_LLC2=m
 CONFIG_ATALK=m
 CONFIG_DEV_APPLETALK=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/nlm_xlr_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/nlm_xlr_defconfig
@@ -198,7 +198,6 @@
 CONFIG_IP6_NF_MANGLE=m
 CONFIG_IP6_NF_RAW=m
 CONFIG_IP6_NF_SECURITY=m
-CONFIG_DECNET_NF_GRABULATOR=m
 CONFIG_BRIDGE_NF_EBTABLES=m
 CONFIG_BRIDGE_EBT_BROUTE=m
 CONFIG_BRIDGE_EBT_T_FILTER=m
@@ -232,7 +231,6 @@
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
 CONFIG_VLAN_8021Q_GVRP=y
-CONFIG_DECNET=m
 CONFIG_LLC2=m
 CONFIG_ATALK=m
 CONFIG_DEV_APPLETALK=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/configs/rm200_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/configs/rm200_defconfig
@@ -116,7 +116,6 @@
 CONFIG_IP6_NF_TARGET_REJECT=m
 CONFIG_IP6_NF_MANGLE=m
 CONFIG_IP6_NF_RAW=m
-CONFIG_DECNET_NF_GRABULATOR=m
 CONFIG_BRIDGE_NF_EBTABLES=m
 CONFIG_BRIDGE_EBT_BROUTE=m
 CONFIG_BRIDGE_EBT_T_FILTER=m
@@ -137,7 +136,6 @@
 CONFIG_BRIDGE_EBT_SNAT=m
 CONFIG_BRIDGE_EBT_LOG=m
 CONFIG_BRIDGE=m
-CONFIG_DECNET=m
 CONFIG_NET_SCHED=y
 CONFIG_NET_SCH_CBQ=m
 CONFIG_NET_SCH_HTB=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/dec/int-handler.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/dec/int-handler.S
@@ -131,7 +131,7 @@
 		 */
 		mfc0	t0,CP0_CAUSE		# get pending interrupts
 		mfc0	t1,CP0_STATUS
-#ifdef CONFIG_32BIT
+#if defined(CONFIG_32BIT) && defined(CONFIG_MIPS_FP_SUPPORT)
 		lw	t2,cpu_fpu_mask
 #endif
 		andi	t0,ST0_IM		# CAUSE.CE may be non-zero!
@@ -139,7 +139,7 @@
 
 		beqz	t0,spurious
 
-#ifdef CONFIG_32BIT
+#if defined(CONFIG_32BIT) && defined(CONFIG_MIPS_FP_SUPPORT)
 		 and	t2,t0
 		bnez	t2,fpu			# handle FPU immediately
 #endif
@@ -280,7 +280,7 @@
 		j	dec_irq_dispatch
 		 nop
 
-#ifdef CONFIG_32BIT
+#if defined(CONFIG_32BIT) && defined(CONFIG_MIPS_FP_SUPPORT)
 fpu:
 		lw	t0,fpu_kstat_irq
 		nop
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/dec/prom/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/dec/prom/Makefile
@@ -6,4 +6,4 @@
 
 lib-y			+= init.o memory.o cmdline.o identify.o console.o
 
-lib-$(CONFIG_32BIT)	+= locore.o
+lib-$(CONFIG_CPU_R3000)	+= locore.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/dec/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/dec/setup.c
@@ -746,7 +746,8 @@
 		dec_interrupt[DEC_IRQ_HALT] = -1;
 
 	/* Register board interrupts: FPU and cascade. */
-	if (dec_interrupt[DEC_IRQ_FPU] >= 0 && cpu_has_fpu) {
+	if (IS_ENABLED(CONFIG_MIPS_FP_SUPPORT) &&
+	    dec_interrupt[DEC_IRQ_FPU] >= 0 && cpu_has_fpu) {
 		struct irq_desc *desc_fpu;
 		int irq_fpu;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/fw/lib/cmdline.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/fw/lib/cmdline.c
@@ -53,7 +53,7 @@
 {
 	char *result = NULL;
 
-	if (_fw_envp != NULL) {
+	if (_fw_envp != NULL && fw_envp(0) != NULL) {
 		/*
 		 * Return a pointer to the given environment variable.
 		 * YAMON uses "name", "value" pairs, while U-Boot uses
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/generic/yamon-dt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/generic/yamon-dt.c
@@ -75,7 +75,7 @@
 __init int yamon_dt_append_memory(void *fdt,
 				  const struct yamon_mem_region *regions)
 {
-	unsigned long phys_memsize, memsize;
+	unsigned long phys_memsize = 0, memsize;
 	__be32 mem_array[2 * MAX_MEM_ARRAY_ENTRIES];
 	unsigned int mem_entries;
 	int i, err, mem_off;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/asm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/asm.h
@@ -276,7 +276,7 @@
 
 #define PTR_SCALESHIFT	2
 
-#define PTR		.word
+#define PTR_WD		.word
 #define PTRSIZE		4
 #define PTRLOG		2
 #endif
@@ -301,7 +301,7 @@
 
 #define PTR_SCALESHIFT	3
 
-#define PTR		.dword
+#define PTR_WD		.dword
 #define PTRSIZE		8
 #define PTRLOG		3
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/bugs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/bugs.h
@@ -1,17 +1,11 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
- * This is included by init/main.c to check for architecture-dependent bugs.
- *
  * Copyright (C) 2007  Maciej W. Rozycki
- *
- * Needs:
- *	void check_bugs(void);
  */
 #ifndef _ASM_BUGS_H
 #define _ASM_BUGS_H
 
 #include <linux/bug.h>
-#include <linux/delay.h>
 #include <linux/smp.h>
 
 #include <asm/cpu.h>
@@ -30,17 +24,6 @@
 		check_bugs64_early();
 }
 
-static inline void check_bugs(void)
-{
-	unsigned int cpu = smp_processor_id();
-
-	cpu_data[cpu].udelay_val = loops_per_jiffy;
-	check_bugs32();
-
-	if (IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
-		check_bugs64();
-}
-
 static inline int r4k_daddiu_bug(void)
 {
 	if (!IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/checksum.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/checksum.h
@@ -244,7 +244,8 @@
 	"	.set	pop"
 	: "=&r" (sum), "=&r" (tmp)
 	: "r" (saddr), "r" (daddr),
-	  "0" (htonl(len)), "r" (htonl(proto)), "r" (sum));
+	  "0" (htonl(len)), "r" (htonl(proto)), "r" (sum)
+	: "memory");
 
 	return csum_fold(sum);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/cmpxchg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/cmpxchg.h
@@ -249,6 +249,7 @@
 	/* Load 64 bits from ptr */
 	"	" __SYNC(full, loongson3_war) "		\n"
 	"1:	lld	%L0, %3		# __cmpxchg64	\n"
+	"	.set	pop				\n"
 	/*
 	 * Split the 64 bit value we loaded into the 2 registers that hold the
 	 * ret variable.
@@ -276,12 +277,14 @@
 	"	or	%L1, %L1, $at			\n"
 	"	.set	at				\n"
 #  endif
+	"	.set	push				\n"
+	"	.set	" MIPS_ISA_ARCH_LEVEL "		\n"
 	/* Attempt to store new at ptr */
 	"	scd	%L1, %2				\n"
 	/* If we failed, loop! */
 	"\t" __SC_BEQZ "%L1, 1b				\n"
-	"	.set	pop				\n"
 	"2:	" __SYNC(full, loongson3_war) "		\n"
+	"	.set	pop				\n"
 	: "=&r"(ret),
 	  "=&r"(tmp),
 	  "=" GCC_OFF_SMALL_ASM() (*(unsigned long long *)ptr)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/cpu-features.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/cpu-features.h
@@ -124,7 +124,24 @@
 #define cpu_has_tx39_cache	__opt(MIPS_CPU_TX39_CACHE)
 #endif
 #ifndef cpu_has_octeon_cache
-#define cpu_has_octeon_cache	0
+#define cpu_has_octeon_cache						\
+({									\
+	int __res;							\
+									\
+	switch (boot_cpu_type()) {					\
+	case CPU_CAVIUM_OCTEON:						\
+	case CPU_CAVIUM_OCTEON_PLUS:					\
+	case CPU_CAVIUM_OCTEON2:					\
+	case CPU_CAVIUM_OCTEON3:					\
+		__res = 1;						\
+		break;							\
+									\
+	default:							\
+		__res = 0;						\
+	}								\
+									\
+	__res;								\
+})
 #endif
 /* Don't override `cpu_has_fpu' to 1 or the "nofpu" option won't work.  */
 #ifndef cpu_has_fpu
@@ -351,7 +368,7 @@
 ({									\
 	int __res;							\
 									\
-	switch (current_cpu_type()) {					\
+	switch (boot_cpu_type()) {					\
 	case CPU_M14KC:							\
 	case CPU_74K:							\
 	case CPU_1074K:							\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/dec/prom.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/dec/prom.h
@@ -43,16 +43,11 @@
  */
 #define REX_PROM_MAGIC		0x30464354
 
-#ifdef CONFIG_64BIT
-
-#define prom_is_rex(magic)	1	/* KN04 and KN05 are REX PROMs.  */
-
-#else /* !CONFIG_64BIT */
-
-#define prom_is_rex(magic)	((magic) == REX_PROM_MAGIC)
-
-#endif /* !CONFIG_64BIT */
-
+/* KN04 and KN05 are REX PROMs, so only do the check for R3k systems.  */
+static inline bool prom_is_rex(u32 magic)
+{
+	return !IS_ENABLED(CONFIG_CPU_R3000) || magic == REX_PROM_MAGIC;
+}
 
 /*
  * 3MIN/MAXINE PROM entry points for DS5000/1xx's, DS5000/xx's and
@@ -75,7 +70,7 @@
  */
 typedef struct {
 	int pagesize;
-	unsigned char bitmap[0];
+	unsigned char bitmap[];
 } memmap;
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/dmi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/dmi.h
@@ -5,7 +5,7 @@
 #include <linux/io.h>
 #include <linux/memblock.h>
 
-#define dmi_early_remap(x, l)		ioremap_cache(x, l)
+#define dmi_early_remap(x, l)		ioremap(x, l)
 #define dmi_early_unmap(x, l)		iounmap(x)
 #define dmi_remap(x, l)			ioremap_cache(x, l)
 #define dmi_unmap(x)			iounmap(x)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/ftrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/ftrace.h
@@ -32,7 +32,7 @@
 		".previous\n"				\
 							\
 		".section\t__ex_table,\"a\"\n\t"	\
-		STR(PTR) "\t1b, 3b\n\t"			\
+		STR(PTR_WD) "\t1b, 3b\n\t"		\
 		".previous\n"				\
 							\
 		: [tmp_dst] "=&r" (dst), [tmp_err] "=r" (error)\
@@ -54,7 +54,7 @@
 		".previous\n"			\
 						\
 		".section\t__ex_table,\"a\"\n\t"\
-		STR(PTR) "\t1b, 3b\n\t"		\
+		STR(PTR_WD) "\t1b, 3b\n\t"	\
 		".previous\n"			\
 						\
 		: [tmp_err] "=r" (error)	\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/fw/fw.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/fw/fw.h
@@ -26,6 +26,6 @@
 extern void fw_meminit(void);
 extern char *fw_getenv(char *name);
 extern unsigned long fw_getenvl(char *name);
-extern void fw_init_early_console(char port);
+extern void fw_init_early_console(void);
 
 #endif /* __ASM_FW_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/kvm_host.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/kvm_host.h
@@ -318,7 +318,7 @@
 	unsigned int aux_inuse;
 
 	/* COP0 State */
-	struct mips_coproc *cop0;
+	struct mips_coproc cop0;
 
 	/* Resume PC after MMIO completion */
 	unsigned long io_pc;
@@ -699,7 +699,7 @@
 static inline bool kvm_mips_guest_has_fpu(struct kvm_vcpu_arch *vcpu)
 {
 	return kvm_mips_guest_can_have_fpu(vcpu) &&
-		kvm_read_c0_guest_config1(vcpu->cop0) & MIPS_CONF1_FP;
+		kvm_read_c0_guest_config1(&vcpu->cop0) & MIPS_CONF1_FP;
 }
 
 static inline bool kvm_mips_guest_can_have_msa(struct kvm_vcpu_arch *vcpu)
@@ -711,7 +711,7 @@
 static inline bool kvm_mips_guest_has_msa(struct kvm_vcpu_arch *vcpu)
 {
 	return kvm_mips_guest_can_have_msa(vcpu) &&
-		kvm_read_c0_guest_config3(vcpu->cop0) & MIPS_CONF3_MSA;
+		kvm_read_c0_guest_config3(&vcpu->cop0) & MIPS_CONF3_MSA;
 }
 
 struct kvm_mips_callbacks {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/local.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/local.h
@@ -5,6 +5,7 @@
 #include <linux/percpu.h>
 #include <linux/bitops.h>
 #include <linux/atomic.h>
+#include <asm/asm.h>
 #include <asm/cmpxchg.h>
 #include <asm/compiler.h>
 #include <asm/war.h>
@@ -39,7 +40,7 @@
 		"	.set	arch=r4000				\n"
 			__SYNC(full, loongson3_war) "			\n"
 		"1:"	__LL	"%1, %2		# local_add_return	\n"
-		"	addu	%0, %1, %3				\n"
+			__stringify(LONG_ADDU)	"	%0, %1, %3	\n"
 			__SC	"%0, %2					\n"
 		"	beqzl	%0, 1b					\n"
 		"	addu	%0, %1, %3				\n"
@@ -55,7 +56,7 @@
 		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
 			__SYNC(full, loongson3_war) "			\n"
 		"1:"	__LL	"%1, %2		# local_add_return	\n"
-		"	addu	%0, %1, %3				\n"
+			__stringify(LONG_ADDU)	"	%0, %1, %3	\n"
 			__SC	"%0, %2					\n"
 		"	beqz	%0, 1b					\n"
 		"	addu	%0, %1, %3				\n"
@@ -88,7 +89,7 @@
 		"	.set	arch=r4000				\n"
 			__SYNC(full, loongson3_war) "			\n"
 		"1:"	__LL	"%1, %2		# local_sub_return	\n"
-		"	subu	%0, %1, %3				\n"
+			__stringify(LONG_SUBU)	"	%0, %1, %3	\n"
 			__SC	"%0, %2					\n"
 		"	beqzl	%0, 1b					\n"
 		"	subu	%0, %1, %3				\n"
@@ -104,7 +105,7 @@
 		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
 			__SYNC(full, loongson3_war) "			\n"
 		"1:"	__LL	"%1, %2		# local_sub_return	\n"
-		"	subu	%0, %1, %3				\n"
+			__stringify(LONG_SUBU)	"	%0, %1, %3	\n"
 			__SC	"%0, %2					\n"
 		"	beqz	%0, 1b					\n"
 		"	subu	%0, %1, %3				\n"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mach-ip27/cpu-feature-overrides.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mach-ip27/cpu-feature-overrides.h
@@ -26,7 +26,6 @@
 #define cpu_has_3k_cache		0
 #define cpu_has_4k_cache		1
 #define cpu_has_tx39_cache		0
-#define cpu_has_fpu			1
 #define cpu_has_nofpuex			0
 #define cpu_has_32fpr			1
 #define cpu_has_counter			1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mach-ip30/cpu-feature-overrides.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mach-ip30/cpu-feature-overrides.h
@@ -29,7 +29,6 @@
 #define cpu_has_3k_cache		0
 #define cpu_has_4k_cache		1
 #define cpu_has_tx39_cache		0
-#define cpu_has_fpu			1
 #define cpu_has_nofpuex			0
 #define cpu_has_32fpr			1
 #define cpu_has_counter			1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mach-loongson64/boot_param.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mach-loongson64/boot_param.h
@@ -14,7 +14,11 @@
 #define ADAPTER_ROM		8
 #define ACPI_TABLE		9
 #define SMBIOS_TABLE		10
-#define MAX_MEMORY_TYPE		11
+#define UMA_VIDEO_RAM		11
+#define VUMA_VIDEO_RAM		12
+#define MAX_MEMORY_TYPE		13
+
+#define MEM_SIZE_IS_IN_BYTES	(1 << 31)
 
 #define LOONGSON3_BOOT_MEM_MAP_MAX 128
 struct efi_memory_map_loongson {
@@ -38,12 +42,14 @@
 	Legacy_1B = 0x5,
 	Legacy_2G = 0x6,
 	Legacy_2H = 0x7,
+	Legacy_2K = 0x8,
 	Loongson_1A = 0x100,
 	Loongson_1B = 0x101,
 	Loongson_2E = 0x200,
 	Loongson_2F = 0x201,
 	Loongson_2G = 0x202,
 	Loongson_2H = 0x203,
+	Loongson_2K = 0x204,
 	Loongson_3A = 0x300,
 	Loongson_3B = 0x301
 };
@@ -117,7 +123,8 @@
 	u64 pci_io_start_addr;
 	u64 pci_io_end_addr;
 	u64 pci_config_addr;
-	u32 dma_mask_bits;
+	u16 dma_mask_bits;
+	u16 dma_noncoherent;
 } __packed;
 
 struct interface_info {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mach-loongson64/kernel-entry-init.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mach-loongson64/kernel-entry-init.h
@@ -32,7 +32,7 @@
 	nop
 	/* Loongson-3A R2/R3 */
 	andi	t0, (PRID_IMP_MASK | PRID_REV_MASK)
-	slti	t0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0)
+	slti	t0, t0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0)
 	bnez	t0, 2f
 	nop
 1:
@@ -63,7 +63,7 @@
 	nop
 	/* Loongson-3A R2/R3 */
 	andi	t0, (PRID_IMP_MASK | PRID_REV_MASK)
-	slti	t0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0)
+	slti	t0, t0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0)
 	bnez	t0, 2f
 	nop
 1:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mach-ralink/mt7621.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mach-ralink/mt7621.h
@@ -7,10 +7,12 @@
 #ifndef _MT7621_REGS_H_
 #define _MT7621_REGS_H_
 
+#define IOMEM(x)			((void __iomem *)(KSEG1ADDR(x)))
+
 #define MT7621_PALMBUS_BASE		0x1C000000
 #define MT7621_PALMBUS_SIZE		0x03FFFFFF
 
-#define MT7621_SYSC_BASE		0x1E000000
+#define MT7621_SYSC_BASE		IOMEM(0x1E000000)
 
 #define SYSC_REG_CHIP_NAME0		0x00
 #define SYSC_REG_CHIP_NAME1		0x04
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mach-rc32434/pci.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mach-rc32434/pci.h
@@ -374,7 +374,7 @@
 				 PCI_CFG04_STAT_SSE | \
 				 PCI_CFG04_STAT_PE)
 
-#define KORINA_CNFG1		((KORINA_STAT<<16)|KORINA_CMD)
+#define KORINA_CNFG1		(KORINA_STAT | KORINA_CMD)
 
 #define KORINA_REVID		0
 #define KORINA_CLASS_CODE	0
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/mips-cm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/mips-cm.h
@@ -11,6 +11,7 @@
 #ifndef __MIPS_ASM_MIPS_CM_H__
 #define __MIPS_ASM_MIPS_CM_H__
 
+#include <linux/bitfield.h>
 #include <linux/bitops.h>
 #include <linux/errno.h>
 
@@ -153,8 +154,8 @@
 #define CM_GCR_REV_MINOR			GENMASK(7, 0)
 
 #define CM_ENCODE_REV(major, minor) \
-		(((major) << __ffs(CM_GCR_REV_MAJOR)) | \
-		 ((minor) << __ffs(CM_GCR_REV_MINOR)))
+		(FIELD_PREP(CM_GCR_REV_MAJOR, major) | \
+		 FIELD_PREP(CM_GCR_REV_MINOR, minor))
 
 #define CM_REV_CM2				CM_ENCODE_REV(6, 0)
 #define CM_REV_CM2_5				CM_ENCODE_REV(7, 0)
@@ -227,6 +228,10 @@
 GCR_ACCESSOR_RO(32, 0x0f0, cpc_status)
 #define CM_GCR_CPC_STATUS_EX			BIT(0)
 
+/* GCR_ACCESS - Controls core/IOCU access to GCRs */
+GCR_ACCESSOR_RW(32, 0x120, access_cm3)
+#define CM_GCR_ACCESS_ACCESSEN			GENMASK(7, 0)
+
 /* GCR_L2_CONFIG - Indicates L2 cache configuration when Config5.L2C=1 */
 GCR_ACCESSOR_RW(32, 0x130, l2_config)
 #define CM_GCR_L2_CONFIG_BYPASS			BIT(20)
@@ -362,10 +367,10 @@
 static inline unsigned int mips_cm_max_vp_width(void)
 {
 	extern int smp_num_siblings;
-	uint32_t cfg;
 
 	if (mips_cm_revision() >= CM_REV_CM3)
-		return read_gcr_sys_config2() & CM_GCR_SYS_CONFIG2_MAXVPW;
+		return FIELD_GET(CM_GCR_SYS_CONFIG2_MAXVPW,
+				 read_gcr_sys_config2());
 
 	if (mips_cm_present()) {
 		/*
@@ -373,8 +378,7 @@
 		 * number of VP(E)s, and if that ever changes then this will
 		 * need revisiting.
 		 */
-		cfg = read_gcr_cl_config() & CM_GCR_Cx_CONFIG_PVPE;
-		return (cfg >> __ffs(CM_GCR_Cx_CONFIG_PVPE)) + 1;
+		return FIELD_GET(CM_GCR_Cx_CONFIG_PVPE, read_gcr_cl_config()) + 1;
 	}
 
 	if (IS_ENABLED(CONFIG_SMP))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/octeon/cvmx-bootinfo.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/octeon/cvmx-bootinfo.h
@@ -318,7 +318,7 @@
 
 /* Functions to return string based on type */
 #define ENUM_BRD_TYPE_CASE(x) \
-	case x: return(#x + 16);	/* Skip CVMX_BOARD_TYPE_ */
+	case x: return (&#x[16]);	/* Skip CVMX_BOARD_TYPE_ */
 static inline const char *cvmx_board_type_to_string(enum
 						    cvmx_board_types_enum type)
 {
@@ -410,7 +410,7 @@
 }
 
 #define ENUM_CHIP_TYPE_CASE(x) \
-	case x: return(#x + 15);	/* Skip CVMX_CHIP_TYPE */
+	case x: return (&#x[15]);	/* Skip CVMX_CHIP_TYPE */
 static inline const char *cvmx_chip_type_to_string(enum
 						   cvmx_chip_types_enum type)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/pgalloc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/pgalloc.h
@@ -15,6 +15,7 @@
 
 #define __HAVE_ARCH_PMD_ALLOC_ONE
 #define __HAVE_ARCH_PUD_ALLOC_ONE
+#define __HAVE_ARCH_PGD_FREE
 #include <asm-generic/pgalloc.h>
 
 static inline void pmd_populate_kernel(struct mm_struct *mm, pmd_t *pmd,
@@ -48,6 +49,11 @@
 extern void pgd_init(unsigned long page);
 extern pgd_t *pgd_alloc(struct mm_struct *mm);
 
+static inline void pgd_free(struct mm_struct *mm, pgd_t *pgd)
+{
+	free_pages((unsigned long)pgd, PGD_ORDER);
+}
+
 #define __pte_free_tlb(tlb,pte,address)			\
 do {							\
 	pgtable_pte_page_dtor(pte);			\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/ptrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/ptrace.h
@@ -60,6 +60,7 @@
                                            unsigned long val)
 {
 	regs->cp0_epc = val;
+	regs->cp0_cause &= ~CAUSEF_BD;
 }
 
 /* Query offset/name of register from its name/offset */
@@ -156,7 +157,7 @@
 #define instruction_pointer(regs) ((regs)->cp0_epc)
 #define profile_pc(regs) instruction_pointer(regs)
 
-extern asmlinkage long syscall_trace_enter(struct pt_regs *regs, long syscall);
+extern asmlinkage long syscall_trace_enter(struct pt_regs *regs);
 extern asmlinkage void syscall_trace_leave(struct pt_regs *regs);
 
 extern void die(const char *, struct pt_regs *) __noreturn;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/r4kcache.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/r4kcache.h
@@ -119,7 +119,7 @@
 	"	j	2b			\n"		\
 	"	.previous			\n"		\
 	"	.section __ex_table,\"a\"	\n"		\
-	"	"STR(PTR)" 1b, 3b		\n"		\
+	"	"STR(PTR_WD)" 1b, 3b		\n"		\
 	"	.previous"					\
 	: "+r" (__err)						\
 	: "i" (op), "r" (addr), "i" (-EFAULT));			\
@@ -142,7 +142,7 @@
 	"	j	2b			\n"		\
 	"	.previous			\n"		\
 	"	.section __ex_table,\"a\"	\n"		\
-	"	"STR(PTR)" 1b, 3b		\n"		\
+	"	"STR(PTR_WD)" 1b, 3b		\n"		\
 	"	.previous"					\
 	: "+r" (__err)						\
 	: "i" (op), "r" (addr), "i" (-EFAULT));			\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/setup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/setup.h
@@ -16,7 +16,7 @@
 	unsigned int reg_shift, unsigned int timeout) {}
 #endif
 
-extern void set_handler(unsigned long offset, void *addr, unsigned long len);
+void set_handler(unsigned long offset, const void *addr, unsigned long len);
 extern void set_uncached_handler(unsigned long offset, void *addr, unsigned long len);
 
 typedef void (*vi_handler_t)(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/switch_to.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/switch_to.h
@@ -97,7 +97,7 @@
 	}								\
 } while (0)
 #else
-# define __sanitize_fcr31(next)
+# define __sanitize_fcr31(next) do { (void) (next); } while (0)
 #endif
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/syscall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/syscall.h
@@ -38,7 +38,7 @@
 static inline long syscall_get_nr(struct task_struct *task,
 				  struct pt_regs *regs)
 {
-	return current_thread_info()->syscall;
+	return task_thread_info(task)->syscall;
 }
 
 static inline void mips_syscall_update_nr(struct task_struct *task,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/timex.h
@@ -40,9 +40,9 @@
 typedef unsigned int cycles_t;
 
 /*
- * On R4000/R4400 before version 5.0 an erratum exists such that if the
- * cycle counter is read in the exact moment that it is matching the
- * compare register, no interrupt will be generated.
+ * On R4000/R4400 an erratum exists such that if the cycle counter is
+ * read in the exact moment that it is matching the compare register,
+ * no interrupt will be generated.
  *
  * There is a suggested workaround and also the erratum can't strike if
  * the compare interrupt isn't being used as the clock source device.
@@ -63,7 +63,7 @@
 	if (!__builtin_constant_p(cpu_has_counter))
 		asm volatile("" : "=m" (cpu_data[0].options));
 	if (likely(cpu_has_counter &&
-		   prid >= (PRID_IMP_R4000 | PRID_REV_ENCODE_44(5, 0))))
+		   prid > (PRID_IMP_R4000 | PRID_REV_ENCODE_44(15, 15))))
 		return 1;
 	else
 		return 0;
@@ -76,25 +76,24 @@
 	else
 		return 0;	/* no usable counter */
 }
+#define get_cycles get_cycles
 
 /*
  * Like get_cycles - but where c0_count is not available we desperately
  * use c0_random in an attempt to get at least a little bit of entropy.
- *
- * R6000 and R6000A neither have a count register nor a random register.
- * That leaves no entropy source in the CPU itself.
  */
 static inline unsigned long random_get_entropy(void)
 {
-	unsigned int prid = read_c0_prid();
-	unsigned int imp = prid & PRID_IMP_MASK;
+	unsigned int c0_random;
 
-	if (can_use_mips_counter(prid))
+	if (can_use_mips_counter(read_c0_prid()))
 		return read_c0_count();
-	else if (likely(imp != PRID_IMP_R6000 && imp != PRID_IMP_R6000A))
-		return read_c0_random();
+
+	if (cpu_has_3kex)
+		c0_random = (read_c0_random() >> 8) & 0x3f;
 	else
-		return 0;	/* no usable register */
+		c0_random = read_c0_random() & 0x3f;
+	return (random_get_entropy_fallback() << 6) | (0x3f - c0_random);
 }
 #define random_get_entropy random_get_entropy
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/unaligned-emul.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/unaligned-emul.h
@@ -20,8 +20,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -41,8 +41,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -74,10 +74,10 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (value), "=r" (res)	    \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -102,8 +102,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -125,8 +125,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -145,8 +145,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -178,10 +178,10 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (value), "=r" (res)	    \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -223,14 +223,14 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
-		STR(PTR)"\t5b, 11b\n\t"		    \
-		STR(PTR)"\t6b, 11b\n\t"		    \
-		STR(PTR)"\t7b, 11b\n\t"		    \
-		STR(PTR)"\t8b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (value), "=r" (res)	    \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -255,8 +255,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"              \
-		STR(PTR)"\t2b, 4b\n\t"              \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=r" (res)                        \
 		: "r" (value), "r" (addr), "i" (-EFAULT));\
@@ -276,8 +276,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=r" (res)                                \
 		: "r" (value), "r" (addr), "i" (-EFAULT));  \
@@ -296,8 +296,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=r" (res)                                \
 		: "r" (value), "r" (addr), "i" (-EFAULT));  \
@@ -325,10 +325,10 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (res)				    \
 		: "r" (value), "r" (addr), "i" (-EFAULT)    \
@@ -365,14 +365,14 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
-		STR(PTR)"\t5b, 11b\n\t"		    \
-		STR(PTR)"\t6b, 11b\n\t"		    \
-		STR(PTR)"\t7b, 11b\n\t"		    \
-		STR(PTR)"\t8b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (res)				    \
 		: "r" (value), "r" (addr), "i" (-EFAULT)    \
@@ -398,8 +398,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -419,8 +419,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -452,10 +452,10 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (value), "=r" (res)	    \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -481,8 +481,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -504,8 +504,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -524,8 +524,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=&r" (value), "=r" (res)         \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -557,10 +557,10 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (value), "=r" (res)	    \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -602,14 +602,14 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
-		STR(PTR)"\t5b, 11b\n\t"		    \
-		STR(PTR)"\t6b, 11b\n\t"		    \
-		STR(PTR)"\t7b, 11b\n\t"		    \
-		STR(PTR)"\t8b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (value), "=r" (res)	    \
 		: "r" (addr), "i" (-EFAULT));       \
@@ -632,8 +632,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=r" (res)                        \
 		: "r" (value), "r" (addr), "i" (-EFAULT));\
@@ -653,8 +653,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=r" (res)                                \
 		: "r" (value), "r" (addr), "i" (-EFAULT));  \
@@ -673,8 +673,8 @@
 		"j\t3b\n\t"                         \
 		".previous\n\t"                     \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 4b\n\t"               \
-		STR(PTR)"\t2b, 4b\n\t"               \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
 		".previous"                         \
 		: "=r" (res)                                \
 		: "r" (value), "r" (addr), "i" (-EFAULT));  \
@@ -703,10 +703,10 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (res)				    \
 		: "r" (value), "r" (addr), "i" (-EFAULT)    \
@@ -743,14 +743,14 @@
 		"j\t10b\n\t"			    \
 		".previous\n\t"			    \
 		".section\t__ex_table,\"a\"\n\t"    \
-		STR(PTR)"\t1b, 11b\n\t"		    \
-		STR(PTR)"\t2b, 11b\n\t"		    \
-		STR(PTR)"\t3b, 11b\n\t"		    \
-		STR(PTR)"\t4b, 11b\n\t"		    \
-		STR(PTR)"\t5b, 11b\n\t"		    \
-		STR(PTR)"\t6b, 11b\n\t"		    \
-		STR(PTR)"\t7b, 11b\n\t"		    \
-		STR(PTR)"\t8b, 11b\n\t"		    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
 		".previous"			    \
 		: "=&r" (res)				    \
 		: "r" (value), "r" (addr), "i" (-EFAULT)    \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/include/asm/vpe.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/include/asm/vpe.h
@@ -102,7 +102,6 @@
 	struct list_head tc_list;       /* Thread contexts */
 };
 
-extern unsigned long physical_memsize;
 extern struct vpe_control vpecontrol;
 extern const struct file_operations vpe_fops;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/asm-offsets.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/asm-offsets.c
@@ -98,6 +98,7 @@
 	OFFSET(TI_CPU, thread_info, cpu);
 	OFFSET(TI_PRE_COUNT, thread_info, preempt_count);
 	OFFSET(TI_REGS, thread_info, regs);
+	OFFSET(TI_SYSCALL, thread_info, syscall);
 	DEFINE(_THREAD_SIZE, THREAD_SIZE);
 	DEFINE(_THREAD_MASK, THREAD_MASK);
 	DEFINE(_IRQ_STACK_SIZE, IRQ_STACK_SIZE);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/cevt-r4k.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/cevt-r4k.c
@@ -303,13 +303,6 @@
 	if (!c0_compare_int_usable())
 		return -ENXIO;
 
-	/*
-	 * With vectored interrupts things are getting platform specific.
-	 * get_c0_compare_int is a hook to allow a platform to return the
-	 * interrupt number of its liking.
-	 */
-	irq = get_c0_compare_int();
-
 	cd = &per_cpu(mips_clockevent_device, cpu);
 
 	cd->name		= "MIPS";
@@ -320,7 +313,6 @@
 	min_delta		= calculate_min_delta();
 
 	cd->rating		= 300;
-	cd->irq			= irq;
 	cd->cpumask		= cpumask_of(cpu);
 	cd->set_next_event	= mips_next_event;
 	cd->event_handler	= mips_event_handler;
@@ -332,6 +324,13 @@
 
 	cp0_timer_irq_installed = 1;
 
+	/*
+	 * With vectored interrupts things are getting platform specific.
+	 * get_c0_compare_int is a hook to allow a platform to return the
+	 * interrupt number of its liking.
+	 */
+	irq = get_c0_compare_int();
+
 	if (request_irq(irq, c0_compare_interrupt, flags, "timer",
 			c0_compare_interrupt))
 		pr_err("Failed to request irq %d (timer)\n", irq);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/cpu-probe.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/cpu-probe.c
@@ -1734,9 +1734,10 @@
 
 static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 {
-	decode_configs(c);
+	c->cputype = CPU_LOONGSON64;
 
 	/* All Loongson processors covered here define ExcCode 16 as GSExc. */
+	decode_configs(c);
 	c->options |= MIPS_CPU_GSEXCEX;
 
 	switch (c->processor_id & PRID_IMP_MASK) {
@@ -1746,7 +1747,6 @@
 		case PRID_REV_LOONGSON2K_R1_1:
 		case PRID_REV_LOONGSON2K_R1_2:
 		case PRID_REV_LOONGSON2K_R1_3:
-			c->cputype = CPU_LOONGSON64;
 			__cpu_name[cpu] = "Loongson-2K";
 			set_elf_platform(cpu, "gs264e");
 			set_isa(c, MIPS_CPU_ISA_M64R2);
@@ -1759,14 +1759,12 @@
 		switch (c->processor_id & PRID_REV_MASK) {
 		case PRID_REV_LOONGSON3A_R2_0:
 		case PRID_REV_LOONGSON3A_R2_1:
-			c->cputype = CPU_LOONGSON64;
 			__cpu_name[cpu] = "ICT Loongson-3";
 			set_elf_platform(cpu, "loongson3a");
 			set_isa(c, MIPS_CPU_ISA_M64R2);
 			break;
 		case PRID_REV_LOONGSON3A_R3_0:
 		case PRID_REV_LOONGSON3A_R3_1:
-			c->cputype = CPU_LOONGSON64;
 			__cpu_name[cpu] = "ICT Loongson-3";
 			set_elf_platform(cpu, "loongson3a");
 			set_isa(c, MIPS_CPU_ISA_M64R2);
@@ -1784,13 +1782,16 @@
 		c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_CAM |
 			MIPS_ASE_LOONGSON_EXT | MIPS_ASE_LOONGSON_EXT2);
 		c->ases &= ~MIPS_ASE_VZ; /* VZ of Loongson-3A2000/3000 is incomplete */
+		change_c0_config6(LOONGSON_CONF6_EXTIMER | LOONGSON_CONF6_INTIMER,
+				  LOONGSON_CONF6_INTIMER);
 		break;
 	case PRID_IMP_LOONGSON_64G:
-		c->cputype = CPU_LOONGSON64;
 		__cpu_name[cpu] = "ICT Loongson-3";
 		set_elf_platform(cpu, "loongson3a");
 		set_isa(c, MIPS_CPU_ISA_M64R2);
 		decode_cpucfg(c);
+		change_c0_config6(LOONGSON_CONF6_EXTIMER | LOONGSON_CONF6_INTIMER,
+				  LOONGSON_CONF6_INTIMER);
 		break;
 	default:
 		panic("Unknown Loongson Processor ID!");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/elf.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/elf.c
@@ -11,6 +11,7 @@
 
 #include <asm/cpu-features.h>
 #include <asm/cpu-info.h>
+#include <asm/fpu.h>
 
 #ifdef CONFIG_MIPS_FP_SUPPORT
 
@@ -309,6 +310,11 @@
 	struct cpuinfo_mips *c = &boot_cpu_data;
 	struct task_struct *t = current;
 
+	/* Do this early so t->thread.fpu.fcr31 won't be clobbered in case
+	 * we are preempted before the lose_fpu(0) in start_thread.
+	 */
+	lose_fpu(0);
+
 	t->thread.fpu.fcr31 = c->fpu_csr31;
 	switch (state->nan_2008) {
 	case 0:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/ftrace.c
@@ -248,7 +248,7 @@
 #define S_R_SP	(0xafb0 << 16)	/* s{d,w} R, offset(sp) */
 #define OFFSET_MASK	0xffff	/* stack offset range: 0 ~ PT_SIZE */
 
-unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
+static unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
 		old_parent_ra, unsigned long parent_ra_addr, unsigned long fp)
 {
 	unsigned long sp, ip, tmp;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/jump_label.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/jump_label.c
@@ -56,7 +56,7 @@
 			 * The branch offset must fit in the instruction's 26
 			 * bit field.
 			 */
-			WARN_ON((offset >= BIT(25)) ||
+			WARN_ON((offset >= (long)BIT(25)) ||
 				(offset < -(long)BIT(25)));
 
 			insn.j_format.opcode = bc6_op;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/kprobes.c
@@ -11,6 +11,8 @@
  *   Copyright (C) IBM Corporation, 2002, 2004
  */
 
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/kprobes.h>
 #include <linux/preempt.h>
 #include <linux/uaccess.h>
@@ -80,8 +82,7 @@
 	insn = p->addr[0];
 
 	if (insn_has_ll_or_sc(insn)) {
-		pr_notice("Kprobes for ll and sc instructions are not"
-			  "supported\n");
+		pr_notice("Kprobes for ll and sc instructions are not supported\n");
 		ret = -EINVAL;
 		goto out;
 	}
@@ -219,7 +220,7 @@
 	return 0;
 
 unaligned:
-	pr_notice("%s: unaligned epc - sending SIGBUS.\n", current->comm);
+	pr_notice("Failed to emulate branch instruction because of unaligned epc - sending SIGBUS to %s.\n", current->comm);
 	force_sig(SIGBUS);
 	return -EFAULT;
 
@@ -238,10 +239,8 @@
 		regs->cp0_epc = (unsigned long)p->addr;
 	else if (insn_has_delayslot(p->opcode)) {
 		ret = evaluate_branch_instruction(p, regs, kcb);
-		if (ret < 0) {
-			pr_notice("Kprobes: Error in evaluating branch\n");
+		if (ret < 0)
 			return;
-		}
 	}
 	regs->cp0_epc = (unsigned long)&p->ainsn.insn[0];
 }
@@ -461,14 +460,14 @@
 		/* Keep the assembler from reordering and placing JR here. */
 		".set noreorder\n\t"
 		"nop\n\t"
-		".global kretprobe_trampoline\n"
-		"kretprobe_trampoline:\n\t"
+		".global __kretprobe_trampoline\n"
+		"__kretprobe_trampoline:\n\t"
 		"nop\n\t"
 		".set pop"
 		: : : "memory");
 }
 
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 
 void __kprobes arch_prepare_kretprobe(struct kretprobe_instance *ri,
 				      struct pt_regs *regs)
@@ -477,7 +476,7 @@
 	ri->fp = NULL;
 
 	/* Replace the return addr with trampoline addr */
-	regs->regs[31] = (unsigned long)kretprobe_trampoline;
+	regs->regs[31] = (unsigned long)__kretprobe_trampoline;
 }
 
 /*
@@ -486,8 +485,7 @@
 static int __kprobes trampoline_probe_handler(struct kprobe *p,
 						struct pt_regs *regs)
 {
-	instruction_pointer(regs) = __kretprobe_trampoline_handler(regs,
-						kretprobe_trampoline, NULL);
+	instruction_pointer(regs) = __kretprobe_trampoline_handler(regs, NULL);
 	/*
 	 * By returning a non-zero value, we are telling
 	 * kprobe_handler() that we don't want the post_handler
@@ -498,14 +496,14 @@
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
 {
-	if (p->addr == (kprobe_opcode_t *)kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)__kretprobe_trampoline)
 		return 1;
 
 	return 0;
 }
 
 static struct kprobe trampoline_p = {
-	.addr = (kprobe_opcode_t *)kretprobe_trampoline,
+	.addr = (kprobe_opcode_t *)__kretprobe_trampoline,
 	.pre_handler = trampoline_probe_handler
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/mips-cm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/mips-cm.c
@@ -221,8 +221,7 @@
 	phys_addr_t addr;
 
 	/* L2-only sync was introduced with CM major revision 6 */
-	major_rev = (read_gcr_rev() & CM_GCR_REV_MAJOR) >>
-		__ffs(CM_GCR_REV_MAJOR);
+	major_rev = FIELD_GET(CM_GCR_REV_MAJOR, read_gcr_rev());
 	if (major_rev < 6)
 		return;
 
@@ -306,13 +305,13 @@
 	preempt_disable();
 
 	if (cm_rev >= CM_REV_CM3) {
-		val = core << __ffs(CM3_GCR_Cx_OTHER_CORE);
-		val |= vp << __ffs(CM3_GCR_Cx_OTHER_VP);
+		val = FIELD_PREP(CM3_GCR_Cx_OTHER_CORE, core) |
+		      FIELD_PREP(CM3_GCR_Cx_OTHER_VP, vp);
 
 		if (cm_rev >= CM_REV_CM3_5) {
 			val |= CM_GCR_Cx_OTHER_CLUSTER_EN;
-			val |= cluster << __ffs(CM_GCR_Cx_OTHER_CLUSTER);
-			val |= block << __ffs(CM_GCR_Cx_OTHER_BLOCK);
+			val |= FIELD_PREP(CM_GCR_Cx_OTHER_CLUSTER, cluster);
+			val |= FIELD_PREP(CM_GCR_Cx_OTHER_BLOCK, block);
 		} else {
 			WARN_ON(cluster != 0);
 			WARN_ON(block != CM_GCR_Cx_OTHER_BLOCK_LOCAL);
@@ -342,7 +341,7 @@
 		spin_lock_irqsave(&per_cpu(cm_core_lock, curr_core),
 				  per_cpu(cm_core_lock_flags, curr_core));
 
-		val = core << __ffs(CM_GCR_Cx_OTHER_CORENUM);
+		val = FIELD_PREP(CM_GCR_Cx_OTHER_CORENUM, core);
 	}
 
 	write_gcr_cl_other(val);
@@ -386,8 +385,8 @@
 	cm_other = read_gcr_error_mult();
 
 	if (revision < CM_REV_CM3) { /* CM2 */
-		cause = cm_error >> __ffs(CM_GCR_ERROR_CAUSE_ERRTYPE);
-		ocause = cm_other >> __ffs(CM_GCR_ERROR_MULT_ERR2ND);
+		cause = FIELD_GET(CM_GCR_ERROR_CAUSE_ERRTYPE, cm_error);
+		ocause = FIELD_GET(CM_GCR_ERROR_MULT_ERR2ND, cm_other);
 
 		if (!cause)
 			return;
@@ -445,8 +444,8 @@
 		ulong core_id_bits, vp_id_bits, cmd_bits, cmd_group_bits;
 		ulong cm3_cca_bits, mcp_bits, cm3_tr_bits, sched_bit;
 
-		cause = cm_error >> __ffs64(CM3_GCR_ERROR_CAUSE_ERRTYPE);
-		ocause = cm_other >> __ffs(CM_GCR_ERROR_MULT_ERR2ND);
+		cause = FIELD_GET(CM3_GCR_ERROR_CAUSE_ERRTYPE, cm_error);
+		ocause = FIELD_GET(CM_GCR_ERROR_MULT_ERR2ND, cm_other);
 
 		if (!cause)
 			return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/mips-cpc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/mips-cpc.c
@@ -27,6 +27,7 @@
 	cpc_node = of_find_compatible_node(of_root, NULL, "mti,mips-cpc");
 	if (cpc_node) {
 		err = of_address_to_resource(cpc_node, 0, &res);
+		of_node_put(cpc_node);
 		if (!err)
 			return res.start;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/mips-r2-to-r6-emul.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/mips-r2-to-r6-emul.c
@@ -1258,10 +1258,10 @@
 			"	j	10b\n"
 			"	.previous\n"
 			"	.section	__ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
 			"	.previous\n"
 			"	.set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1333,10 +1333,10 @@
 			"	j	10b\n"
 			"       .previous\n"
 			"	.section	__ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
 			"	.previous\n"
 			"	.set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1404,10 +1404,10 @@
 			"	j	9b\n"
 			"	.previous\n"
 			"	.section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
 			"	.previous\n"
 			"	.set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1474,10 +1474,10 @@
 			"	j	9b\n"
 			"	.previous\n"
 			"	.section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
 			"	.previous\n"
 			"	.set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1589,14 +1589,14 @@
 			"	j	9b\n"
 			"	.previous\n"
 			"	.section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
-			STR(PTR) " 5b,8b\n"
-			STR(PTR) " 6b,8b\n"
-			STR(PTR) " 7b,8b\n"
-			STR(PTR) " 0b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
 			"	.previous\n"
 			"	.set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1708,14 +1708,14 @@
 			"	j      9b\n"
 			"	.previous\n"
 			"	.section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
-			STR(PTR) " 5b,8b\n"
-			STR(PTR) " 6b,8b\n"
-			STR(PTR) " 7b,8b\n"
-			STR(PTR) " 0b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
 			"	.previous\n"
 			"	.set    pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1827,14 +1827,14 @@
 			"	j	9b\n"
 			"	.previous\n"
 			"	.section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
-			STR(PTR) " 5b,8b\n"
-			STR(PTR) " 6b,8b\n"
-			STR(PTR) " 7b,8b\n"
-			STR(PTR) " 0b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
 			"	.previous\n"
 			"	.set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -1945,14 +1945,14 @@
 			"       j	9b\n"
 			"       .previous\n"
 			"       .section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,8b\n"
-			STR(PTR) " 2b,8b\n"
-			STR(PTR) " 3b,8b\n"
-			STR(PTR) " 4b,8b\n"
-			STR(PTR) " 5b,8b\n"
-			STR(PTR) " 6b,8b\n"
-			STR(PTR) " 7b,8b\n"
-			STR(PTR) " 0b,8b\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
 			"       .previous\n"
 			"       .set	pop\n"
 			: "+&r"(rt), "=&r"(rs),
@@ -2007,7 +2007,7 @@
 			"j	2b\n"
 			".previous\n"
 			".section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,3b\n"
+			STR(PTR_WD) " 1b,3b\n"
 			".previous\n"
 			: "=&r"(res), "+&r"(err)
 			: "r"(vaddr), "i"(SIGSEGV)
@@ -2065,7 +2065,7 @@
 			"j	2b\n"
 			".previous\n"
 			".section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,3b\n"
+			STR(PTR_WD) " 1b,3b\n"
 			".previous\n"
 			: "+&r"(res), "+&r"(err)
 			: "r"(vaddr), "i"(SIGSEGV));
@@ -2126,7 +2126,7 @@
 			"j	2b\n"
 			".previous\n"
 			".section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,3b\n"
+			STR(PTR_WD) " 1b,3b\n"
 			".previous\n"
 			: "=&r"(res), "+&r"(err)
 			: "r"(vaddr), "i"(SIGSEGV)
@@ -2189,7 +2189,7 @@
 			"j	2b\n"
 			".previous\n"
 			".section        __ex_table,\"a\"\n"
-			STR(PTR) " 1b,3b\n"
+			STR(PTR_WD) " 1b,3b\n"
 			".previous\n"
 			: "+&r"(res), "+&r"(err)
 			: "r"(vaddr), "i"(SIGSEGV));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/proc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/proc.c
@@ -172,7 +172,7 @@
 {
 	unsigned long i = *pos;
 
-	return i < NR_CPUS ? (void *) (i + 1) : NULL;
+	return i < nr_cpu_ids ? (void *) (i + 1) : NULL;
 }
 
 static void *c_next(struct seq_file *m, void *v, loff_t *pos)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/ptrace.c
@@ -1310,16 +1310,13 @@
  * Notification of system call entry/exit
  * - triggered by current->work.syscall_trace
  */
-asmlinkage long syscall_trace_enter(struct pt_regs *regs, long syscall)
+asmlinkage long syscall_trace_enter(struct pt_regs *regs)
 {
 	user_exit();
 
-	current_thread_info()->syscall = syscall;
-
 	if (test_thread_flag(TIF_SYSCALL_TRACE)) {
 		if (tracehook_report_syscall_entry(regs))
 			return -1;
-		syscall = current_thread_info()->syscall;
 	}
 
 #ifdef CONFIG_SECCOMP
@@ -1328,7 +1325,7 @@
 		struct seccomp_data sd;
 		unsigned long args[6];
 
-		sd.nr = syscall;
+		sd.nr = current_thread_info()->syscall;
 		sd.arch = syscall_get_arch(current);
 		syscall_get_arguments(current, regs, args);
 		for (i = 0; i < 6; i++)
@@ -1338,23 +1335,23 @@
 		ret = __secure_computing(&sd);
 		if (ret == -1)
 			return ret;
-		syscall = current_thread_info()->syscall;
 	}
 #endif
 
 	if (unlikely(test_thread_flag(TIF_SYSCALL_TRACEPOINT)))
 		trace_sys_enter(regs, regs->regs[2]);
 
-	audit_syscall_entry(syscall, regs->regs[4], regs->regs[5],
+	audit_syscall_entry(current_thread_info()->syscall,
+			    regs->regs[4], regs->regs[5],
 			    regs->regs[6], regs->regs[7]);
 
 	/*
 	 * Negative syscall numbers are mistaken for rejected syscalls, but
 	 * won't have had the return value set appropriately, so we do so now.
 	 */
-	if (syscall < 0)
+	if (current_thread_info()->syscall < 0)
 		syscall_set_return_value(current, regs, -ENOSYS, 0);
-	return syscall;
+	return current_thread_info()->syscall;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/r2300_fpu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/r2300_fpu.S
@@ -23,14 +23,14 @@
 #define EX(a,b)							\
 9:	a,##b;							\
 	.section __ex_table,"a";				\
-	PTR	9b,fault;					\
+	PTR_WD	9b,fault;					\
 	.previous
 
 #define EX2(a,b)						\
 9:	a,##b;							\
 	.section __ex_table,"a";				\
-	PTR	9b,bad_stack;					\
-	PTR	9b+4,bad_stack;					\
+	PTR_WD	9b,fault;					\
+	PTR_WD	9b+4,fault;					\
 	.previous
 
 	.set	mips1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/r4k_fpu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/r4k_fpu.S
@@ -31,7 +31,7 @@
 .ex\@:	\insn	\reg, \src
 	.set	pop
 	.section __ex_table,"a"
-	PTR	.ex\@, fault
+	PTR_WD	.ex\@, fault
 	.previous
 	.endm
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/relocate_kernel.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/relocate_kernel.S
@@ -145,12 +145,11 @@
  * kexec_args[0..3] are used to prepare register values.
  */
 
-kexec_args:
-	EXPORT(kexec_args)
-arg0:	PTR		0x0
-arg1:	PTR		0x0
-arg2:	PTR		0x0
-arg3:	PTR		0x0
+EXPORT(kexec_args)
+arg0:	PTR_WD		0x0
+arg1:	PTR_WD		0x0
+arg2:	PTR_WD		0x0
+arg3:	PTR_WD		0x0
 	.size	kexec_args,PTRSIZE*4
 
 #ifdef CONFIG_SMP
@@ -159,31 +158,27 @@
  * their registers a0-a3. secondary_kexec_args[0..3] are used
  * to prepare register values.
  */
-secondary_kexec_args:
-	EXPORT(secondary_kexec_args)
-s_arg0: PTR		0x0
-s_arg1: PTR		0x0
-s_arg2: PTR		0x0
-s_arg3: PTR		0x0
+EXPORT(secondary_kexec_args)
+s_arg0: PTR_WD		0x0
+s_arg1: PTR_WD		0x0
+s_arg2: PTR_WD		0x0
+s_arg3: PTR_WD		0x0
 	.size	secondary_kexec_args,PTRSIZE*4
 kexec_flag:
 	LONG		0x1
 
 #endif
 
-kexec_start_address:
-	EXPORT(kexec_start_address)
-	PTR		0x0
+EXPORT(kexec_start_address)
+	PTR_WD		0x0
 	.size		kexec_start_address, PTRSIZE
 
-kexec_indirection_page:
-	EXPORT(kexec_indirection_page)
-	PTR		0
+EXPORT(kexec_indirection_page)
+	PTR_WD		0
 	.size		kexec_indirection_page, PTRSIZE
 
 relocate_new_kernel_end:
 
-relocate_new_kernel_size:
-	EXPORT(relocate_new_kernel_size)
-	PTR		relocate_new_kernel_end - relocate_new_kernel
+EXPORT(relocate_new_kernel_size)
+	PTR_WD		relocate_new_kernel_end - relocate_new_kernel
 	.size		relocate_new_kernel_size, PTRSIZE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/scall32-o32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/scall32-o32.S
@@ -72,12 +72,24 @@
 	.set	pop
 
 	.section __ex_table,"a"
-	PTR	load_a4, bad_stack_a4
-	PTR	load_a5, bad_stack_a5
-	PTR	load_a6, bad_stack_a6
-	PTR	load_a7, bad_stack_a7
+	PTR_WD	load_a4, bad_stack_a4
+	PTR_WD	load_a5, bad_stack_a5
+	PTR_WD	load_a6, bad_stack_a6
+	PTR_WD	load_a7, bad_stack_a7
 	.previous
 
+	/*
+	 * syscall number is in v0 unless we called syscall(__NR_###)
+	 * where the real syscall number is in a0
+	 */
+	subu	t2, v0,  __NR_O32_Linux
+	bnez	t2, 1f /* __NR_syscall at offset 0 */
+	LONG_S	a0, TI_SYSCALL($28)	# Save a0 as syscall number
+	b	2f
+1:
+	LONG_S	v0, TI_SYSCALL($28)	# Save v0 as syscall number
+2:
+
 	lw	t0, TI_FLAGS($28)	# syscall tracing enabled?
 	li	t1, _TIF_WORK_SYSCALL_ENTRY
 	and	t0, t1
@@ -115,16 +127,7 @@
 	SAVE_STATIC
 	move	a0, sp
 
-	/*
-	 * syscall number is in v0 unless we called syscall(__NR_###)
-	 * where the real syscall number is in a0
-	 */
-	move	a1, v0
-	subu	t2, v0,  __NR_O32_Linux
-	bnez	t2, 1f /* __NR_syscall at offset 0 */
-	lw	a1, PT_R4(sp)
-
-1:	jal	syscall_trace_enter
+	jal	syscall_trace_enter
 
 	bltz	v0, 1f			# seccomp failed? Skip syscall
 
@@ -216,7 +219,7 @@
 #endif /* CONFIG_MIPS_MT_FPAFF */
 
 #define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, native)
-#define __SYSCALL(nr, entry) 	PTR entry
+#define __SYSCALL(nr, entry) 	PTR_WD entry
 	.align	2
 	.type	sys_call_table, @object
 EXPORT(sys_call_table)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/scall64-n32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/scall64-n32.S
@@ -44,6 +44,8 @@
 
 	sd	a3, PT_R26(sp)		# save a3 for syscall restarting
 
+	LONG_S	v0, TI_SYSCALL($28)     # Store syscall number
+
 	li	t1, _TIF_WORK_SYSCALL_ENTRY
 	LONG_L	t0, TI_FLAGS($28)	# syscall tracing enabled?
 	and	t0, t1, t0
@@ -72,7 +74,6 @@
 n32_syscall_trace_entry:
 	SAVE_STATIC
 	move	a0, sp
-	move	a1, v0
 	jal	syscall_trace_enter
 
 	bltz	v0, 1f			# seccomp failed? Skip syscall
@@ -101,7 +102,7 @@
 
 	END(handle_sysn32)
 
-#define __SYSCALL(nr, entry)	PTR entry
+#define __SYSCALL(nr, entry)	PTR_WD entry
 	.type	sysn32_call_table, @object
 EXPORT(sysn32_call_table)
 #include <asm/syscall_table_n32.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/scall64-n64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/scall64-n64.S
@@ -47,6 +47,8 @@
 
 	sd	a3, PT_R26(sp)		# save a3 for syscall restarting
 
+	LONG_S	v0, TI_SYSCALL($28)     # Store syscall number
+
 	li	t1, _TIF_WORK_SYSCALL_ENTRY
 	LONG_L	t0, TI_FLAGS($28)	# syscall tracing enabled?
 	and	t0, t1, t0
@@ -83,7 +85,6 @@
 syscall_trace_entry:
 	SAVE_STATIC
 	move	a0, sp
-	move	a1, v0
 	jal	syscall_trace_enter
 
 	bltz	v0, 1f			# seccomp failed? Skip syscall
@@ -109,7 +110,7 @@
 	j	n64_syscall_exit
 	END(handle_sys64)
 
-#define __SYSCALL(nr, entry)	PTR entry
+#define __SYSCALL(nr, entry)	PTR_WD entry
 	.align	3
 	.type	sys_call_table, @object
 EXPORT(sys_call_table)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/scall64-o32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/scall64-o32.S
@@ -73,12 +73,28 @@
 loads_done:
 
 	.section __ex_table,"a"
-	PTR	load_a4, bad_stack_a4
-	PTR	load_a5, bad_stack_a5
-	PTR	load_a6, bad_stack_a6
-	PTR	load_a7, bad_stack_a7
+	PTR_WD	load_a4, bad_stack_a4
+	PTR_WD	load_a5, bad_stack_a5
+	PTR_WD	load_a6, bad_stack_a6
+	PTR_WD	load_a7, bad_stack_a7
 	.previous
 
+	/*
+	 * absolute syscall number is in v0 unless we called syscall(__NR_###)
+	 * where the real syscall number is in a0
+	 * note: NR_syscall is the first O32 syscall but the macro is
+	 * only defined when compiling with -mabi=32 (CONFIG_32BIT)
+	 * therefore __NR_O32_Linux is used (4000)
+	 */
+
+	subu	t2, v0,  __NR_O32_Linux
+	bnez	t2, 1f /* __NR_syscall at offset 0 */
+	LONG_S	a0, TI_SYSCALL($28)	# Save a0 as syscall number
+	b	2f
+1:
+	LONG_S	v0, TI_SYSCALL($28)	# Save v0 as syscall number
+2:
+
 	li	t1, _TIF_WORK_SYSCALL_ENTRY
 	LONG_L	t0, TI_FLAGS($28)	# syscall tracing enabled?
 	and	t0, t1, t0
@@ -113,22 +129,7 @@
 	sd	a7, PT_R11(sp)		# For indirect syscalls
 
 	move	a0, sp
-	/*
-	 * absolute syscall number is in v0 unless we called syscall(__NR_###)
-	 * where the real syscall number is in a0
-	 * note: NR_syscall is the first O32 syscall but the macro is
-	 * only defined when compiling with -mabi=32 (CONFIG_32BIT)
-	 * therefore __NR_O32_Linux is used (4000)
-	 */
-	.set	push
-	.set	reorder
-	subu	t1, v0,  __NR_O32_Linux
-	move	a1, v0
-	bnez	t1, 1f /* __NR_syscall at offset 0 */
-	ld	a1, PT_R4(sp) /* Arg1 for __NR_syscall case */
-	.set	pop
-
-1:	jal	syscall_trace_enter
+	jal	syscall_trace_enter
 
 	bltz	v0, 1f			# seccomp failed? Skip syscall
 
@@ -214,7 +215,7 @@
 	END(sys32_syscall)
 
 #define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, compat)
-#define __SYSCALL(nr, entry)	PTR entry
+#define __SYSCALL(nr, entry)	PTR_WD entry
 	.align	3
 	.type	sys32_call_table,@object
 EXPORT(sys32_call_table)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/setup.c
@@ -11,6 +11,8 @@
  * Copyright (C) 2000, 2001, 2002, 2007	 Maciej W. Rozycki
  */
 #include <linux/init.h>
+#include <linux/cpu.h>
+#include <linux/delay.h>
 #include <linux/ioport.h>
 #include <linux/export.h>
 #include <linux/screen_info.h>
@@ -156,10 +158,6 @@
 		pr_err("initrd start must be page aligned\n");
 		goto disable;
 	}
-	if (initrd_start < PAGE_OFFSET) {
-		pr_err("initrd start < PAGE_OFFSET\n");
-		goto disable;
-	}
 
 	/*
 	 * Sanitize initrd addresses. For example firmware
@@ -172,6 +170,11 @@
 	initrd_end = (unsigned long)__va(end);
 	initrd_start = (unsigned long)__va(__pa(initrd_start));
 
+	if (initrd_start < PAGE_OFFSET) {
+		pr_err("initrd start < PAGE_OFFSET\n");
+		goto disable;
+	}
+
 	ROOT_DEV = Root_RAM0;
 	return PFN_UP(end);
 disable:
@@ -321,11 +324,11 @@
 		panic("Incorrect memory mapping !!!");
 
 	if (max_pfn > PFN_DOWN(HIGHMEM_START)) {
+		max_low_pfn = PFN_DOWN(HIGHMEM_START);
 #ifdef CONFIG_HIGHMEM
-		highstart_pfn = PFN_DOWN(HIGHMEM_START);
+		highstart_pfn = max_low_pfn;
 		highend_pfn = max_pfn;
 #else
-		max_low_pfn = PFN_DOWN(HIGHMEM_START);
 		max_pfn = max_low_pfn;
 #endif
 	}
@@ -803,9 +806,20 @@
 
 static int __init setnocoherentio(char *str)
 {
-	dma_default_coherent = true;
+	dma_default_coherent = false;
 	pr_info("Software DMA cache coherency (command line)\n");
 	return 0;
 }
 early_param("nocoherentio", setnocoherentio);
 #endif
+
+void __init arch_cpu_finalize_init(void)
+{
+	unsigned int cpu = smp_processor_id();
+
+	cpu_data[cpu].udelay_val = loops_per_jiffy;
+	check_bugs32();
+
+	if (IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
+		check_bugs64();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/smp-cps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/smp-cps.c
@@ -230,7 +230,10 @@
 	write_gcr_co_reset_ext_base(CM_GCR_Cx_RESET_EXT_BASE_UEB);
 
 	/* Ensure the core can access the GCRs */
-	set_gcr_access(1 << core);
+	if (mips_cm_revision() < CM_REV_CM3)
+		set_gcr_access(1 << core);
+	else
+		set_gcr_access_cm3(1 << core);
 
 	if (mips_cpc_present()) {
 		/* Reset the core */
@@ -424,9 +427,11 @@
 			wmb();
 		}
 	} else {
-		pr_debug("Gating power to core %d\n", core);
-		/* Power down the core */
-		cps_pm_enter_state(CPS_PM_POWER_GATED);
+		if (IS_ENABLED(CONFIG_HOTPLUG_CPU)) {
+			pr_debug("Gating power to core %d\n", core);
+			/* Power down the core */
+			cps_pm_enter_state(CPS_PM_POWER_GATED);
+		}
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/smp.c
@@ -351,6 +351,9 @@
 	cpu = smp_processor_id();
 	cpu_data[cpu].udelay_val = loops_per_jiffy;
 
+	set_cpu_sibling_map(cpu);
+	set_cpu_core_map(cpu);
+
 	cpumask_set_cpu(cpu, &cpu_coherent_mask);
 	notify_cpu_starting(cpu);
 
@@ -362,9 +365,6 @@
 	/* The CPU is running and counters synchronised, now mark it online */
 	set_cpu_online(cpu, true);
 
-	set_cpu_sibling_map(cpu);
-	set_cpu_core_map(cpu);
-
 	calculate_cpu_foreign_map();
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/syscall.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/syscall.c
@@ -122,8 +122,8 @@
 		"	j	3b					\n"
 		"	.previous					\n"
 		"	.section __ex_table,\"a\"			\n"
-		"	"STR(PTR)"	1b, 4b				\n"
-		"	"STR(PTR)"	2b, 4b				\n"
+		"	"STR(PTR_WD)"	1b, 4b				\n"
+		"	"STR(PTR_WD)"	2b, 4b				\n"
 		"	.previous					\n"
 		"	.set	pop					\n"
 		: [old] "=&r" (old),
@@ -152,8 +152,8 @@
 		"	j	3b					\n"
 		"	.previous					\n"
 		"	.section __ex_table,\"a\"			\n"
-		"	"STR(PTR)"	1b, 5b				\n"
-		"	"STR(PTR)"	2b, 5b				\n"
+		"	"STR(PTR_WD)"	1b, 5b				\n"
+		"	"STR(PTR_WD)"	2b, 5b				\n"
 		"	.previous					\n"
 		"	.set	pop					\n"
 		: [old] "=&r" (old),
@@ -240,12 +240,3 @@
 {
 	return -ENOSYS;
 }
-
-/*
- * If we ever come here the user sp is bad.  Zap the process right away.
- * Due to the bad stack signaling wouldn't work.
- */
-asmlinkage void bad_stack(void)
-{
-	do_exit(SIGSEGV);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/syscalls/syscall_n32.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/syscalls/syscall_n32.tbl
@@ -354,7 +354,7 @@
 412	n32	utimensat_time64		sys_utimensat
 413	n32	pselect6_time64			compat_sys_pselect6_time64
 414	n32	ppoll_time64			compat_sys_ppoll_time64
-416	n32	io_pgetevents_time64		sys_io_pgetevents
+416	n32	io_pgetevents_time64		compat_sys_io_pgetevents_time64
 417	n32	recvmmsg_time64			compat_sys_recvmmsg_time64
 418	n32	mq_timedsend_time64		sys_mq_timedsend
 419	n32	mq_timedreceive_time64		sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/syscalls/syscall_o32.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/syscalls/syscall_o32.tbl
@@ -27,7 +27,7 @@
 17	o32	break				sys_ni_syscall
 # 18 was sys_stat
 18	o32	unused18			sys_ni_syscall
-19	o32	lseek				sys_lseek
+19	o32	lseek				sys_lseek			compat_sys_lseek
 20	o32	getpid				sys_getpid
 21	o32	mount				sys_mount
 22	o32	umount				sys_oldumount
@@ -403,7 +403,7 @@
 412	o32	utimensat_time64		sys_utimensat			sys_utimensat
 413	o32	pselect6_time64			sys_pselect6			compat_sys_pselect6_time64
 414	o32	ppoll_time64			sys_ppoll			compat_sys_ppoll_time64
-416	o32	io_pgetevents_time64		sys_io_pgetevents		sys_io_pgetevents
+416	o32	io_pgetevents_time64		sys_io_pgetevents		compat_sys_io_pgetevents_time64
 417	o32	recvmmsg_time64			sys_recvmmsg			compat_sys_recvmmsg_time64
 418	o32	mq_timedsend_time64		sys_mq_timedsend		sys_mq_timedsend
 419	o32	mq_timedreceive_time64		sys_mq_timedreceive		sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/time.c
@@ -141,15 +141,10 @@
 	case CPU_R4400MC:
 		/*
 		 * The published errata for the R4400 up to 3.0 say the CPU
-		 * has the mfc0 from count bug.
+		 * has the mfc0 from count bug.  This seems the last version
+		 * produced.
 		 */
-		if ((current_cpu_data.processor_id & 0xff) <= 0x30)
-			return 1;
-
-		/*
-		 * we assume newer revisions are ok
-		 */
-		return 0;
+		return 1;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/traps.c
@@ -416,7 +416,7 @@
 	if (regs && kexec_should_crash(current))
 		crash_kexec(regs);
 
-	do_exit(sig);
+	make_task_dead(sig);
 }
 
 extern struct exception_table_entry __start___dbe_table[];
@@ -2001,7 +2001,13 @@
 
 void reserve_exception_space(phys_addr_t addr, unsigned long size)
 {
-	memblock_reserve(addr, size);
+	/*
+	 * reserve exception space on CPUs other than CPU0
+	 * is too late, since memblock is unavailable when APs
+	 * up
+	 */
+	if (smp_processor_id() == 0)
+		memblock_reserve(addr, size);
 }
 
 void __init *set_except_vector(int n, void *addr)
@@ -2085,19 +2091,19 @@
 		 * If no shadow set is selected then use the default handler
 		 * that does normal register saving and standard interrupt exit
 		 */
-		extern char except_vec_vi, except_vec_vi_lui;
-		extern char except_vec_vi_ori, except_vec_vi_end;
-		extern char rollback_except_vec_vi;
-		char *vec_start = using_rollback_handler() ?
-			&rollback_except_vec_vi : &except_vec_vi;
+		extern const u8 except_vec_vi[], except_vec_vi_lui[];
+		extern const u8 except_vec_vi_ori[], except_vec_vi_end[];
+		extern const u8 rollback_except_vec_vi[];
+		const u8 *vec_start = using_rollback_handler() ?
+				      rollback_except_vec_vi : except_vec_vi;
 #if defined(CONFIG_CPU_MICROMIPS) || defined(CONFIG_CPU_BIG_ENDIAN)
-		const int lui_offset = &except_vec_vi_lui - vec_start + 2;
-		const int ori_offset = &except_vec_vi_ori - vec_start + 2;
+		const int lui_offset = except_vec_vi_lui - vec_start + 2;
+		const int ori_offset = except_vec_vi_ori - vec_start + 2;
 #else
-		const int lui_offset = &except_vec_vi_lui - vec_start;
-		const int ori_offset = &except_vec_vi_ori - vec_start;
+		const int lui_offset = except_vec_vi_lui - vec_start;
+		const int ori_offset = except_vec_vi_ori - vec_start;
 #endif
-		const int handler_len = &except_vec_vi_end - vec_start;
+		const int handler_len = except_vec_vi_end - vec_start;
 
 		if (handler_len > VECTORSPACING) {
 			/*
@@ -2305,7 +2311,7 @@
 }
 
 /* Install CPU exception handler */
-void set_handler(unsigned long offset, void *addr, unsigned long size)
+void set_handler(unsigned long offset, const void *addr, unsigned long size)
 {
 #ifdef CONFIG_CPU_MICROMIPS
 	memcpy((void *)(ebase + offset), ((unsigned char *)addr - 1), size);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/vdso.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/vdso.c
@@ -159,7 +159,7 @@
 	/* Map GIC user page. */
 	if (gic_size) {
 		gic_base = (unsigned long)mips_gic_base + MIPS_GIC_USER_OFS;
-		gic_pfn = virt_to_phys((void *)gic_base) >> PAGE_SHIFT;
+		gic_pfn = PFN_DOWN(__pa(gic_base));
 
 		ret = io_remap_pfn_range(vma, base, gic_pfn, gic_size,
 					 pgprot_noncached(vma->vm_page_prot));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/vmlinux.lds.S
@@ -15,6 +15,8 @@
 #define EMITS_PT_NOTE
 #endif
 
+#define RUNTIME_DISCARD_EXIT
+
 #include <asm-generic/vmlinux.lds.h>
 
 #undef mips
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/vpe-cmp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/vpe-cmp.c
@@ -75,7 +75,6 @@
 
 static void vpe_device_release(struct device *cd)
 {
-	kfree(cd);
 }
 
 static struct class vpe_class = {
@@ -157,6 +156,7 @@
 	device_del(&vpe_device);
 
 out_class:
+	put_device(&vpe_device);
 	class_unregister(&vpe_class);
 
 out_chrdev:
@@ -169,7 +169,7 @@
 {
 	struct vpe *v, *n;
 
-	device_del(&vpe_device);
+	device_unregister(&vpe_device);
 	class_unregister(&vpe_class);
 	unregister_chrdev(major, VPE_MODULE_NAME);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kernel/vpe-mt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kernel/vpe-mt.c
@@ -92,12 +92,11 @@
 	write_tc_c0_tchalt(read_tc_c0_tchalt() & ~TCHALT_H);
 
 	/*
-	 * The sde-kit passes 'memsize' to __start in $a3, so set something
-	 * here...  Or set $a3 to zero and define DFLT_STACK_SIZE and
-	 * DFLT_HEAP_SIZE when you compile your program
+	 * We don't pass the memsize here, so VPE programs need to be
+	 * compiled with DFLT_STACK_SIZE and DFLT_HEAP_SIZE defined.
 	 */
+	mttgpr(7, 0);
 	mttgpr(6, v->ntcs);
-	mttgpr(7, physical_memsize);
 
 	/* set up VPE1 */
 	/*
@@ -313,7 +312,6 @@
 
 static void vpe_device_release(struct device *cd)
 {
-	kfree(cd);
 }
 
 static struct class vpe_class = {
@@ -497,6 +495,7 @@
 	device_del(&vpe_device);
 
 out_class:
+	put_device(&vpe_device);
 	class_unregister(&vpe_class);
 
 out_chrdev:
@@ -509,7 +508,7 @@
 {
 	struct vpe *v, *n;
 
-	device_del(&vpe_device);
+	device_unregister(&vpe_device);
 	class_unregister(&vpe_class);
 	unregister_chrdev(major, VPE_MODULE_NAME);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kvm/emulate.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kvm/emulate.c
@@ -312,7 +312,7 @@
  */
 int kvm_mips_count_disabled(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 
 	return	(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC) ||
 		(kvm_read_c0_guest_cause(cop0) & CAUSEF_DC);
@@ -384,7 +384,7 @@
  */
 static u32 kvm_mips_read_count_running(struct kvm_vcpu *vcpu, ktime_t now)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	ktime_t expires, threshold;
 	u32 count, compare;
 	int running;
@@ -444,7 +444,7 @@
  */
 u32 kvm_mips_read_count(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 
 	/* If count disabled just read static copy of count */
 	if (kvm_mips_count_disabled(vcpu))
@@ -502,7 +502,7 @@
 static void kvm_mips_resume_hrtimer(struct kvm_vcpu *vcpu,
 				    ktime_t now, u32 count)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 compare;
 	u64 delta;
 	ktime_t expire;
@@ -603,7 +603,7 @@
  */
 void kvm_mips_write_count(struct kvm_vcpu *vcpu, u32 count)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	ktime_t now;
 
 	/* Calculate bias */
@@ -649,7 +649,7 @@
  */
 int kvm_mips_set_count_hz(struct kvm_vcpu *vcpu, s64 count_hz)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	int dc;
 	ktime_t now;
 	u32 count;
@@ -696,7 +696,7 @@
  */
 void kvm_mips_write_compare(struct kvm_vcpu *vcpu, u32 compare, bool ack)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	int dc;
 	u32 old_compare = kvm_read_c0_guest_compare(cop0);
 	s32 delta = compare - old_compare;
@@ -779,7 +779,7 @@
  */
 static ktime_t kvm_mips_count_disable(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 count;
 	ktime_t now;
 
@@ -806,7 +806,7 @@
  */
 void kvm_mips_count_disable_cause(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 
 	kvm_set_c0_guest_cause(cop0, CAUSEF_DC);
 	if (!(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC))
@@ -826,7 +826,7 @@
  */
 void kvm_mips_count_enable_cause(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 count;
 
 	kvm_clear_c0_guest_cause(cop0, CAUSEF_DC);
@@ -852,7 +852,7 @@
  */
 int kvm_mips_set_count_ctl(struct kvm_vcpu *vcpu, s64 count_ctl)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	s64 changed = count_ctl ^ vcpu->arch.count_ctl;
 	s64 delta;
 	ktime_t expire, now;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kvm/mips.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kvm/mips.c
@@ -652,7 +652,7 @@
 static int kvm_mips_get_reg(struct kvm_vcpu *vcpu,
 			    const struct kvm_one_reg *reg)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	struct mips_fpu_struct *fpu = &vcpu->arch.fpu;
 	int ret;
 	s64 v;
@@ -764,7 +764,7 @@
 static int kvm_mips_set_reg(struct kvm_vcpu *vcpu,
 			    const struct kvm_one_reg *reg)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	struct mips_fpu_struct *fpu = &vcpu->arch.fpu;
 	s64 v;
 	s64 vs[2];
@@ -1104,7 +1104,7 @@
 int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
 {
 	return kvm_mips_pending_timer(vcpu) ||
-		kvm_read_c0_guest_cause(vcpu->arch.cop0) & C_TI;
+		kvm_read_c0_guest_cause(&vcpu->arch.cop0) & C_TI;
 }
 
 int kvm_arch_vcpu_dump_regs(struct kvm_vcpu *vcpu)
@@ -1128,7 +1128,7 @@
 	kvm_debug("\thi: 0x%08lx\n", vcpu->arch.hi);
 	kvm_debug("\tlo: 0x%08lx\n", vcpu->arch.lo);
 
-	cop0 = vcpu->arch.cop0;
+	cop0 = &vcpu->arch.cop0;
 	kvm_debug("\tStatus: 0x%08x, Cause: 0x%08x\n",
 		  kvm_read_c0_guest_status(cop0),
 		  kvm_read_c0_guest_cause(cop0));
@@ -1250,7 +1250,7 @@
 
 	case EXCCODE_TLBS:
 		kvm_debug("TLB ST fault:  cause %#x, status %#x, PC: %p, BadVaddr: %#lx\n",
-			  cause, kvm_read_c0_guest_status(vcpu->arch.cop0), opc,
+			  cause, kvm_read_c0_guest_status(&vcpu->arch.cop0), opc,
 			  badvaddr);
 
 		++vcpu->stat.tlbmiss_st_exits;
@@ -1322,7 +1322,7 @@
 		kvm_get_badinstr(opc, vcpu, &inst);
 		kvm_err("Exception Code: %d, not yet handled, @ PC: %p, inst: 0x%08x  BadVaddr: %#lx Status: %#x\n",
 			exccode, opc, inst, badvaddr,
-			kvm_read_c0_guest_status(vcpu->arch.cop0));
+			kvm_read_c0_guest_status(&vcpu->arch.cop0));
 		kvm_arch_vcpu_dump_regs(vcpu);
 		run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
 		ret = RESUME_HOST;
@@ -1384,7 +1384,7 @@
 /* Enable FPU for guest and restore context */
 void kvm_own_fpu(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int sr, cfg5;
 
 	preempt_disable();
@@ -1428,7 +1428,7 @@
 /* Enable MSA for guest and restore context */
 void kvm_own_msa(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int sr, cfg5;
 
 	preempt_disable();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kvm/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kvm/mmu.c
@@ -593,7 +593,7 @@
 	gfn_t gfn = gpa >> PAGE_SHIFT;
 	int srcu_idx, err;
 	kvm_pfn_t pfn;
-	pte_t *ptep, entry, old_pte;
+	pte_t *ptep, entry;
 	bool writeable;
 	unsigned long prot_bits;
 	unsigned long mmu_seq;
@@ -665,7 +665,6 @@
 	entry = pfn_pte(pfn, __pgprot(prot_bits));
 
 	/* Write the PTE */
-	old_pte = *ptep;
 	set_pte(ptep, entry);
 
 	err = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kvm/stats.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kvm/stats.c
@@ -54,9 +54,9 @@
 	kvm_info("\nKVM VCPU[%d] COP0 Access Profile:\n", vcpu->vcpu_id);
 	for (i = 0; i < N_MIPS_COPROC_REGS; i++) {
 		for (j = 0; j < N_MIPS_COPROC_SEL; j++) {
-			if (vcpu->arch.cop0->stat[i][j])
+			if (vcpu->arch.cop0.stat[i][j])
 				kvm_info("%s[%d]: %lu\n", kvm_cop0_str[i], j,
-					 vcpu->arch.cop0->stat[i][j]);
+					 vcpu->arch.cop0.stat[i][j]);
 		}
 	}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kvm/trace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kvm/trace.h
@@ -322,11 +322,11 @@
 	    ),
 
 	    TP_fast_assign(
-			__entry->epc = kvm_read_c0_guest_epc(vcpu->arch.cop0);
+			__entry->epc = kvm_read_c0_guest_epc(&vcpu->arch.cop0);
 			__entry->pc = vcpu->arch.pc;
-			__entry->badvaddr = kvm_read_c0_guest_badvaddr(vcpu->arch.cop0);
-			__entry->status = kvm_read_c0_guest_status(vcpu->arch.cop0);
-			__entry->cause = kvm_read_c0_guest_cause(vcpu->arch.cop0);
+			__entry->badvaddr = kvm_read_c0_guest_badvaddr(&vcpu->arch.cop0);
+			__entry->status = kvm_read_c0_guest_status(&vcpu->arch.cop0);
+			__entry->cause = kvm_read_c0_guest_cause(&vcpu->arch.cop0);
 	    ),
 
 	    TP_printk("EPC: 0x%08lx PC: 0x%08lx Status: 0x%08x Cause: 0x%08x BadVAddr: 0x%08lx",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/kvm/vz.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/kvm/vz.c
@@ -422,7 +422,7 @@
  */
 static void kvm_vz_restore_timer(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 cause, compare;
 
 	compare = kvm_read_sw_gc0_compare(cop0);
@@ -517,7 +517,7 @@
  */
 static void kvm_vz_save_timer(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 gctl0, compare, cause;
 
 	gctl0 = read_c0_guestctl0();
@@ -863,7 +863,7 @@
 
 static void kvm_write_maari(struct kvm_vcpu *vcpu, unsigned long val)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 
 	val &= MIPS_MAARI_INDEX;
 	if (val == MIPS_MAARI_INDEX)
@@ -876,7 +876,7 @@
 					      u32 *opc, u32 cause,
 					      struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	enum emulation_result er = EMULATE_DONE;
 	u32 rt, rd, sel;
 	unsigned long curr_pc;
@@ -1905,7 +1905,7 @@
 			      const struct kvm_one_reg *reg,
 			      s64 *v)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int idx;
 
 	switch (reg->id) {
@@ -2075,7 +2075,7 @@
 	case KVM_REG_MIPS_CP0_MAARI:
 		if (!cpu_guest_has_maar || cpu_guest_has_dyn_maar)
 			return -EINVAL;
-		*v = kvm_read_sw_gc0_maari(vcpu->arch.cop0);
+		*v = kvm_read_sw_gc0_maari(&vcpu->arch.cop0);
 		break;
 #ifdef CONFIG_64BIT
 	case KVM_REG_MIPS_CP0_XCONTEXT:
@@ -2129,7 +2129,7 @@
 			      const struct kvm_one_reg *reg,
 			      s64 v)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int idx;
 	int ret = 0;
 	unsigned int cur, change;
@@ -2556,7 +2556,7 @@
 
 static int kvm_vz_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	bool migrated, all;
 
 	/*
@@ -2698,7 +2698,7 @@
 
 static int kvm_vz_vcpu_put(struct kvm_vcpu *vcpu, int cpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 
 	if (current->flags & PF_VCPU)
 		kvm_vz_vcpu_save_wired(vcpu);
@@ -3070,7 +3070,7 @@
 
 static int kvm_vz_vcpu_setup(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned long count_hz = 100*1000*1000; /* default to 100 MHz */
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lantiq/clk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lantiq/clk.c
@@ -50,6 +50,7 @@
 {
 	return &cpu_clk_generic[2];
 }
+EXPORT_SYMBOL_GPL(clk_get_io);
 
 struct clk *clk_get_ppe(void)
 {
@@ -158,6 +159,18 @@
 }
 EXPORT_SYMBOL(clk_deactivate);
 
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return NULL;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
 static inline u32 get_counter_resolution(void)
 {
 	u32 res;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lantiq/falcon/sysctrl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lantiq/falcon/sysctrl.c
@@ -167,6 +167,8 @@
 {
 	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
 
+	if (!clk)
+		return;
 	clk->cl.dev_id = dev;
 	clk->cl.con_id = NULL;
 	clk->cl.clk = clk;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lantiq/prom.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lantiq/prom.c
@@ -23,12 +23,6 @@
 EXPORT_SYMBOL_GPL(ebu_lock);
 
 /*
- * This is needed by the VPE loader code, just set it to 0 and assume
- * that the firmware hardcodes this value to something useful.
- */
-unsigned long physical_memsize = 0L;
-
-/*
  * this struct is filled by the soc specific detection code and holds
  * information about the specific soc type, revision and name
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lantiq/xway/dma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lantiq/xway/dma.c
@@ -11,6 +11,7 @@
 #include <linux/export.h>
 #include <linux/spinlock.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/of.h>
 
@@ -30,6 +31,7 @@
 #define LTQ_DMA_PCTRL		0x44
 #define LTQ_DMA_IRNEN		0xf4
 
+#define DMA_ID_CHNR		GENMASK(26, 20)	/* channel number */
 #define DMA_DESCPT		BIT(3)		/* descriptor complete irq */
 #define DMA_TX			BIT(8)		/* TX channel direction */
 #define DMA_CHAN_ON		BIT(0)		/* channel on / off bit */
@@ -39,8 +41,11 @@
 #define DMA_IRQ_ACK		0x7e		/* IRQ status register */
 #define DMA_POLL		BIT(31)		/* turn on channel polling */
 #define DMA_CLK_DIV4		BIT(6)		/* polling clock divider */
-#define DMA_2W_BURST		BIT(1)		/* 2 word burst length */
-#define DMA_MAX_CHANNEL		20		/* the soc has 20 channels */
+#define DMA_PCTRL_2W_BURST	0x1		/* 2 word burst length */
+#define DMA_PCTRL_4W_BURST	0x2		/* 4 word burst length */
+#define DMA_PCTRL_8W_BURST	0x3		/* 8 word burst length */
+#define DMA_TX_BURST_SHIFT	4		/* tx burst shift */
+#define DMA_RX_BURST_SHIFT	2		/* rx burst shift */
 #define DMA_ETOP_ENDIANNESS	(0xf << 8) /* endianness swap etop channels */
 #define DMA_WEIGHT	(BIT(17) | BIT(16))	/* default channel wheight */
 
@@ -191,7 +196,8 @@
 		break;
 
 	case DMA_PORT_DEU:
-		ltq_dma_w32((DMA_2W_BURST << 4) | (DMA_2W_BURST << 2),
+		ltq_dma_w32((DMA_PCTRL_2W_BURST << DMA_TX_BURST_SHIFT) |
+			(DMA_PCTRL_2W_BURST << DMA_RX_BURST_SHIFT),
 			LTQ_DMA_PCTRL);
 		break;
 
@@ -206,7 +212,7 @@
 {
 	struct clk *clk;
 	struct resource *res;
-	unsigned id;
+	unsigned int id, nchannels;
 	int i;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -222,21 +228,24 @@
 	clk_enable(clk);
 	ltq_dma_w32_mask(0, DMA_RESET, LTQ_DMA_CTRL);
 
+	usleep_range(1, 10);
+
 	/* disable all interrupts */
 	ltq_dma_w32(0, LTQ_DMA_IRNEN);
 
 	/* reset/configure each channel */
-	for (i = 0; i < DMA_MAX_CHANNEL; i++) {
+	id = ltq_dma_r32(LTQ_DMA_ID);
+	nchannels = ((id & DMA_ID_CHNR) >> 20);
+	for (i = 0; i < nchannels; i++) {
 		ltq_dma_w32(i, LTQ_DMA_CS);
 		ltq_dma_w32(DMA_CHAN_RST, LTQ_DMA_CCTRL);
 		ltq_dma_w32(DMA_POLL | DMA_CLK_DIV4, LTQ_DMA_CPOLL);
 		ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL);
 	}
 
-	id = ltq_dma_r32(LTQ_DMA_ID);
 	dev_info(&pdev->dev,
 		"Init done - hw rev: %X, ports: %d, channels: %d\n",
-		id & 0x1f, (id >> 16) & 0xf, id >> 20);
+		id & 0x1f, (id >> 16) & 0xf, nchannels);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lantiq/xway/gptu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lantiq/xway/gptu.c
@@ -122,6 +122,8 @@
 {
 	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
 
+	if (!clk)
+		return;
 	clk->cl.dev_id = dev_name(dev);
 	clk->cl.con_id = con;
 	clk->cl.clk = clk;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lantiq/xway/sysctrl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lantiq/xway/sysctrl.c
@@ -315,6 +315,8 @@
 {
 	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
 
+	if (!clk)
+		return;
 	clk->cl.dev_id = dev;
 	clk->cl.con_id = con;
 	clk->cl.clk = clk;
@@ -338,6 +340,8 @@
 {
 	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
 
+	if (!clk)
+		return;
 	clk->cl.dev_id = dev;
 	clk->cl.con_id = con;
 	clk->cl.clk = clk;
@@ -356,24 +360,28 @@
 	struct clk *clk_ext = kzalloc(sizeof(struct clk), GFP_KERNEL);
 
 	/* main pci clock */
-	clk->cl.dev_id = "17000000.pci";
-	clk->cl.con_id = NULL;
-	clk->cl.clk = clk;
-	clk->rate = CLOCK_33M;
-	clk->rates = valid_pci_rates;
-	clk->enable = pci_enable;
-	clk->disable = pmu_disable;
-	clk->module = 0;
-	clk->bits = PMU_PCI;
-	clkdev_add(&clk->cl);
+	if (clk) {
+		clk->cl.dev_id = "17000000.pci";
+		clk->cl.con_id = NULL;
+		clk->cl.clk = clk;
+		clk->rate = CLOCK_33M;
+		clk->rates = valid_pci_rates;
+		clk->enable = pci_enable;
+		clk->disable = pmu_disable;
+		clk->module = 0;
+		clk->bits = PMU_PCI;
+		clkdev_add(&clk->cl);
+	}
 
 	/* use internal/external bus clock */
-	clk_ext->cl.dev_id = "17000000.pci";
-	clk_ext->cl.con_id = "external";
-	clk_ext->cl.clk = clk_ext;
-	clk_ext->enable = pci_ext_enable;
-	clk_ext->disable = pci_ext_disable;
-	clkdev_add(&clk_ext->cl);
+	if (clk_ext) {
+		clk_ext->cl.dev_id = "17000000.pci";
+		clk_ext->cl.con_id = "external";
+		clk_ext->cl.clk = clk_ext;
+		clk_ext->enable = pci_ext_enable;
+		clk_ext->disable = pci_ext_disable;
+		clkdev_add(&clk_ext->cl);
+	}
 }
 
 /* xway socs can generate clocks on gpio pins */
@@ -393,9 +401,15 @@
 		char *name;
 
 		name = kzalloc(sizeof("clkout0"), GFP_KERNEL);
+		if (!name)
+			continue;
 		sprintf(name, "clkout%d", i);
 
 		clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+		if (!clk) {
+			kfree(name);
+			continue;
+		}
 		clk->cl.dev_id = "1f103000.cgu";
 		clk->cl.con_id = name;
 		clk->cl.clk = clk;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lib/csum_partial.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lib/csum_partial.S
@@ -347,7 +347,7 @@
 	.if \mode == LEGACY_MODE;		\
 9:		insn reg, addr;			\
 		.section __ex_table,"a";	\
-		PTR	9b, .L_exc;		\
+		PTR_WD	9b, .L_exc;		\
 		.previous;			\
 	/* This is enabled in EVA mode */	\
 	.else;					\
@@ -356,7 +356,7 @@
 		    ((\to == USEROP) && (type == ST_INSN));	\
 9:			__BUILD_EVA_INSN(insn##e, reg, addr);	\
 			.section __ex_table,"a";		\
-			PTR	9b, .L_exc;			\
+			PTR_WD	9b, .L_exc;			\
 			.previous;				\
 		.else;						\
 			/* EVA without exception */		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lib/memcpy.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lib/memcpy.S
@@ -116,7 +116,7 @@
 	.if \mode == LEGACY_MODE;				\
 9:		insn reg, addr;					\
 		.section __ex_table,"a";			\
-		PTR	9b, handler;				\
+		PTR_WD	9b, handler;				\
 		.previous;					\
 	/* This is assembled in EVA mode */			\
 	.else;							\
@@ -125,7 +125,7 @@
 		    ((\to == USEROP) && (type == ST_INSN));	\
 9:			__BUILD_EVA_INSN(insn##e, reg, addr);	\
 			.section __ex_table,"a";		\
-			PTR	9b, handler;			\
+			PTR_WD	9b, handler;			\
 			.previous;				\
 		.else;						\
 			/*					\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lib/memset.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lib/memset.S
@@ -52,7 +52,7 @@
 9:		___BUILD_EVA_INSN(insn, reg, addr);	\
 	.endif;						\
 	.section __ex_table,"a";			\
-	PTR	9b, handler;				\
+	PTR_WD	9b, handler;				\
 	.previous
 
 	.macro	f_fill64 dst, offset, val, fixup, mode
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lib/strncpy_user.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lib/strncpy_user.S
@@ -15,7 +15,7 @@
 #define EX(insn,reg,addr,handler)			\
 9:	insn	reg, addr;				\
 	.section __ex_table,"a";			\
-	PTR	9b, handler;				\
+	PTR_WD	9b, handler;				\
 	.previous
 
 /*
@@ -59,7 +59,7 @@
 	jr		ra
 
 	.section	__ex_table,"a"
-	PTR		1b, .Lfault
+	PTR_WD		1b, .Lfault
 	.previous
 
 	EXPORT_SYMBOL(__strncpy_from_user_asm)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/lib/strnlen_user.S
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/lib/strnlen_user.S
@@ -14,7 +14,7 @@
 #define EX(insn,reg,addr,handler)			\
 9:	insn	reg, addr;				\
 	.section __ex_table,"a";			\
-	PTR	9b, handler;				\
+	PTR_WD	9b, handler;				\
 	.previous
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson32/common/platform.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson32/common/platform.c
@@ -98,7 +98,7 @@
 	if (plat_dat->bus_id) {
 		__raw_writel(__raw_readl(LS1X_MUX_CTRL0) | GMAC1_USE_UART1 |
 			     GMAC1_USE_UART0, LS1X_MUX_CTRL0);
-		switch (plat_dat->interface) {
+		switch (plat_dat->phy_interface) {
 		case PHY_INTERFACE_MODE_RGMII:
 			val &= ~(GMAC1_USE_TXCLK | GMAC1_USE_PWM23);
 			break;
@@ -107,12 +107,12 @@
 			break;
 		default:
 			pr_err("unsupported mii mode %d\n",
-			       plat_dat->interface);
+			       plat_dat->phy_interface);
 			return -ENOTSUPP;
 		}
 		val &= ~GMAC1_SHUT;
 	} else {
-		switch (plat_dat->interface) {
+		switch (plat_dat->phy_interface) {
 		case PHY_INTERFACE_MODE_RGMII:
 			val &= ~(GMAC0_USE_TXCLK | GMAC0_USE_PWM01);
 			break;
@@ -121,7 +121,7 @@
 			break;
 		default:
 			pr_err("unsupported mii mode %d\n",
-			       plat_dat->interface);
+			       plat_dat->phy_interface);
 			return -ENOTSUPP;
 		}
 		val &= ~GMAC0_SHUT;
@@ -131,7 +131,7 @@
 	plat_dat = dev_get_platdata(&pdev->dev);
 
 	val &= ~PHY_INTF_SELI;
-	if (plat_dat->interface == PHY_INTERFACE_MODE_RMII)
+	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_RMII)
 		val |= 0x4 << PHY_INTF_SELI_SHIFT;
 	__raw_writel(val, LS1X_MUX_CTRL1);
 
@@ -146,9 +146,9 @@
 	.bus_id			= 0,
 	.phy_addr		= -1,
 #if defined(CONFIG_LOONGSON1_LS1B)
-	.interface		= PHY_INTERFACE_MODE_MII,
+	.phy_interface		= PHY_INTERFACE_MODE_MII,
 #elif defined(CONFIG_LOONGSON1_LS1C)
-	.interface		= PHY_INTERFACE_MODE_RMII,
+	.phy_interface		= PHY_INTERFACE_MODE_RMII,
 #endif
 	.mdio_bus_data		= &ls1x_mdio_bus_data,
 	.dma_cfg		= &ls1x_eth_dma_cfg,
@@ -186,7 +186,7 @@
 static struct plat_stmmacenet_data ls1x_eth1_pdata = {
 	.bus_id			= 1,
 	.phy_addr		= -1,
-	.interface		= PHY_INTERFACE_MODE_MII,
+	.phy_interface		= PHY_INTERFACE_MODE_MII,
 	.mdio_bus_data		= &ls1x_mdio_bus_data,
 	.dma_cfg		= &ls1x_eth_dma_cfg,
 	.has_gmac		= 1,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson32/ls1c/board.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson32/ls1c/board.c
@@ -15,7 +15,6 @@
 static int __init ls1c_platform_init(void)
 {
 	ls1x_serial_set_uartclk(&ls1x_uart_pdev);
-	ls1x_rtc_set_extclk(&ls1x_rtc_pdev);
 
 	return platform_add_devices(ls1c_platform_devices,
 				   ARRAY_SIZE(ls1c_platform_devices));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson64/boardinfo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson64/boardinfo.c
@@ -21,13 +21,11 @@
 		       "BIOS Info\n"
 		       "Vendor\t\t\t: %s\n"
 		       "Version\t\t\t: %s\n"
-		       "ROM Size\t\t: %d KB\n"
 		       "Release Date\t\t: %s\n",
 		       strsep(&tmp_board_manufacturer, "-"),
 		       eboard->name,
 		       strsep(&tmp_bios_vendor, "-"),
 		       einter->description,
-		       einter->size,
 		       especial->special_name);
 }
 static struct kobj_attribute boardinfo_attr = __ATTR(boardinfo, 0444,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson64/env.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson64/env.c
@@ -13,6 +13,8 @@
  * Copyright (C) 2009 Lemote Inc.
  * Author: Wu Zhangjin, wuzhangjin@gmail.com
  */
+
+#include <linux/dma-map-ops.h>
 #include <linux/export.h>
 #include <linux/pci_ids.h>
 #include <asm/bootinfo.h>
@@ -86,6 +88,12 @@
 	cpu_clock_freq = ecpu->cpu_clock_freq;
 	loongson_sysconf.cputype = ecpu->cputype;
 	switch (ecpu->cputype) {
+	case Legacy_2K:
+	case Loongson_2K:
+		smp_group[0] = 0x900000001fe11000;
+		loongson_sysconf.cores_per_node = 2;
+		loongson_sysconf.cores_per_package = 2;
+		break;
 	case Legacy_3A:
 	case Loongson_3A:
 		loongson_sysconf.cores_per_node = 4;
@@ -147,8 +155,14 @@
 
 	loongson_sysconf.dma_mask_bits = eirq_source->dma_mask_bits;
 	if (loongson_sysconf.dma_mask_bits < 32 ||
-		loongson_sysconf.dma_mask_bits > 64)
+			loongson_sysconf.dma_mask_bits > 64) {
 		loongson_sysconf.dma_mask_bits = 32;
+		dma_default_coherent = true;
+	} else {
+		dma_default_coherent = !eirq_source->dma_noncoherent;
+	}
+
+	pr_info("Firmware: Coherent DMA: %s\n", dma_default_coherent ? "on" : "off");
 
 	loongson_sysconf.restart_addr = boot_p->reset_system.ResetWarm;
 	loongson_sysconf.poweroff_addr = boot_p->reset_system.Shutdown;
@@ -213,6 +227,8 @@
 		default:
 			break;
 		}
+	} else if ((read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64R) {
+		loongson_fdt_blob = __dtb_loongson64_2core_2k1000_begin;
 	} else if ((read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64G) {
 		if (loongson_sysconf.bridgetype == LS7A)
 			loongson_fdt_blob = __dtb_loongson64g_4core_ls7a_begin;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson64/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson64/init.c
@@ -49,8 +49,7 @@
 void __init szmem(unsigned int node)
 {
 	u32 i, mem_type;
-	static unsigned long num_physpages;
-	u64 node_id, node_psize, start_pfn, end_pfn, mem_start, mem_size;
+	phys_addr_t node_id, mem_start, mem_size;
 
 	/* Otherwise come from DTB */
 	if (loongson_sysconf.fw_interface != LOONGSON_LEFI)
@@ -64,28 +63,46 @@
 
 		mem_type = loongson_memmap->map[i].mem_type;
 		mem_size = loongson_memmap->map[i].mem_size;
-		mem_start = loongson_memmap->map[i].mem_start;
+
+		/* Memory size comes in MB if MEM_SIZE_IS_IN_BYTES not set */
+		if (mem_size & MEM_SIZE_IS_IN_BYTES)
+			mem_size &= ~MEM_SIZE_IS_IN_BYTES;
+		else
+			mem_size = mem_size << 20;
+
+		mem_start = (node_id << 44) | loongson_memmap->map[i].mem_start;
 
 		switch (mem_type) {
 		case SYSTEM_RAM_LOW:
 		case SYSTEM_RAM_HIGH:
-			start_pfn = ((node_id << 44) + mem_start) >> PAGE_SHIFT;
-			node_psize = (mem_size << 20) >> PAGE_SHIFT;
-			end_pfn  = start_pfn + node_psize;
-			num_physpages += node_psize;
-			pr_info("Node%d: mem_type:%d, mem_start:0x%llx, mem_size:0x%llx MB\n",
-				(u32)node_id, mem_type, mem_start, mem_size);
-			pr_info("       start_pfn:0x%llx, end_pfn:0x%llx, num_physpages:0x%lx\n",
-				start_pfn, end_pfn, num_physpages);
-			memblock_add_node(PFN_PHYS(start_pfn), PFN_PHYS(node_psize), node);
+		case UMA_VIDEO_RAM:
+			pr_info("Node %d, mem_type:%d\t[%pa], %pa bytes usable\n",
+				(u32)node_id, mem_type, &mem_start, &mem_size);
+			memblock_add_node(mem_start, mem_size, node,
+					  MEMBLOCK_NONE);
 			break;
 		case SYSTEM_RAM_RESERVED:
-			pr_info("Node%d: mem_type:%d, mem_start:0x%llx, mem_size:0x%llx MB\n",
-				(u32)node_id, mem_type, mem_start, mem_size);
-			memblock_reserve(((node_id << 44) + mem_start), mem_size << 20);
+		case VIDEO_ROM:
+		case ADAPTER_ROM:
+		case ACPI_TABLE:
+		case SMBIOS_TABLE:
+			pr_info("Node %d, mem_type:%d\t[%pa], %pa bytes reserved\n",
+				(u32)node_id, mem_type, &mem_start, &mem_size);
+			memblock_reserve(mem_start, mem_size);
+			break;
+		/* We should not reserve VUMA_VIDEO_RAM as it overlaps with MMIO */
+		case VUMA_VIDEO_RAM:
+		default:
+			pr_info("Node %d, mem_type:%d\t[%pa], %pa bytes unhandled\n",
+				(u32)node_id, mem_type, &mem_start, &mem_size);
 			break;
 		}
 	}
+
+	/* Reserve vgabios if it comes from firmware */
+	if (loongson_sysconf.vgabios_addr)
+		memblock_reserve(virt_to_phys((void *)loongson_sysconf.vgabios_addr),
+				SZ_256K);
 }
 
 #ifndef CONFIG_NUMA
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson64/reset.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson64/reset.c
@@ -16,6 +16,7 @@
 #include <asm/bootinfo.h>
 #include <asm/idle.h>
 #include <asm/reboot.h>
+#include <asm/bug.h>
 
 #include <loongson.h>
 #include <boot_param.h>
@@ -159,8 +160,17 @@
 
 #ifdef CONFIG_KEXEC
 	kexec_argv = kmalloc(KEXEC_ARGV_SIZE, GFP_KERNEL);
+	if (WARN_ON(!kexec_argv))
+		return -ENOMEM;
+
 	kdump_argv = kmalloc(KEXEC_ARGV_SIZE, GFP_KERNEL);
+	if (WARN_ON(!kdump_argv))
+		return -ENOMEM;
+
 	kexec_envp = kmalloc(KEXEC_ENVP_SIZE, GFP_KERNEL);
+	if (WARN_ON(!kexec_envp))
+		return -ENOMEM;
+
 	fw_arg1 = KEXEC_ARGV_ADDR;
 	memcpy(kexec_envp, (void *)fw_arg2, KEXEC_ENVP_SIZE);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson64/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson64/smp.c
@@ -479,12 +479,25 @@
 static void __init loongson3_smp_setup(void)
 {
 	int i = 0, num = 0; /* i: physical id, num: logical id */
+	int max_cpus = 0;
 
 	init_cpu_possible(cpu_none_mask);
 
+	for (i = 0; i < ARRAY_SIZE(smp_group); i++) {
+		if (!smp_group[i])
+			break;
+		max_cpus += loongson_sysconf.cores_per_node;
+	}
+
+	if (max_cpus < loongson_sysconf.nr_cpus) {
+		pr_err("SMP Groups are less than the number of CPUs\n");
+		loongson_sysconf.nr_cpus = max_cpus ? max_cpus : 1;
+	}
+
 	/* For unified kernel, NR_CPUS is the maximum possible value,
 	 * loongson_sysconf.nr_cpus is the really present value
 	 */
+	i = 0;
 	while (i < loongson_sysconf.nr_cpus) {
 		if (loongson_sysconf.reserved_cpus_mask & (1<<i)) {
 			/* Reserved physical CPU cores */
@@ -505,14 +518,14 @@
 		__cpu_logical_map[num] = -1;
 		num++;
 	}
-
 	csr_ipi_probe();
 	ipi_set0_regs_init();
 	ipi_clear0_regs_init();
 	ipi_status0_regs_init();
 	ipi_en0_regs_init();
 	ipi_mailbox_buf_init();
-	ipi_write_enable(0);
+	if (smp_group[0])
+		ipi_write_enable(0);
 
 	cpu_set_core(&cpu_data[0],
 		     cpu_logical_map(0) % loongson_sysconf.cores_per_package);
@@ -830,6 +843,9 @@
 	uint64_t core_id = cpu_core(&cpu_data[cpu]);
 	uint64_t package_id = cpu_data[cpu].package;
 
+	if (!loongson_chipcfg[package_id] || !loongson_freqctrl[package_id])
+		return 0;
+
 	if ((read_c0_prid() & PRID_REV_MASK) == PRID_REV_LOONGSON3A_R1) {
 		LOONGSON_CHIPCFG(package_id) &= ~(1 << (12 + core_id));
 	} else {
@@ -844,6 +860,9 @@
 	uint64_t core_id = cpu_core(&cpu_data[cpu]);
 	uint64_t package_id = cpu_data[cpu].package;
 
+	if (!loongson_chipcfg[package_id] || !loongson_freqctrl[package_id])
+		return 0;
+
 	if ((read_c0_prid() & PRID_REV_MASK) == PRID_REV_LOONGSON3A_R1) {
 		LOONGSON_CHIPCFG(package_id) |= 1 << (12 + core_id);
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/loongson64/vbios_quirk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/loongson64/vbios_quirk.c
@@ -3,7 +3,7 @@
 #include <linux/pci.h>
 #include <loongson.h>
 
-static void pci_fixup_radeon(struct pci_dev *pdev)
+static void pci_fixup_video(struct pci_dev *pdev)
 {
 	struct resource *res = &pdev->resource[PCI_ROM_RESOURCE];
 
@@ -22,8 +22,7 @@
 	res->flags = IORESOURCE_MEM | IORESOURCE_ROM_SHADOW |
 		     IORESOURCE_PCI_FIXED;
 
-	dev_info(&pdev->dev, "BAR %d: assigned %pR for Radeon ROM\n",
-		 PCI_ROM_RESOURCE, res);
+	dev_info(&pdev->dev, "Video device with shadowed ROM at %pR\n", res);
 }
-DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, 0x9615,
-				PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_radeon);
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_ATI, 0x9615,
+			       PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/math-emu/cp1emu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/math-emu/cp1emu.c
@@ -1660,7 +1660,7 @@
 		break;
 	}
 
-	case 0x3:
+	case 0x7:
 		if (MIPSInst_FUNC(ir) != pfetch_op)
 			return SIGILL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/mm/init.c
@@ -417,7 +417,12 @@
 		       (highend_pfn - max_low_pfn) << (PAGE_SHIFT - 10));
 		max_zone_pfns[ZONE_HIGHMEM] = max_low_pfn;
 	}
+
+	max_mapnr = highend_pfn ? highend_pfn : max_low_pfn;
+#else
+	max_mapnr = max_low_pfn;
 #endif
+	high_memory = (void *) __va(max_low_pfn << PAGE_SHIFT);
 
 	free_area_init(max_zone_pfns);
 }
@@ -453,13 +458,6 @@
 	 */
 	BUILD_BUG_ON(IS_ENABLED(CONFIG_32BIT) && (_PFN_SHIFT > PAGE_SHIFT));
 
-#ifdef CONFIG_HIGHMEM
-	max_mapnr = highend_pfn ? highend_pfn : max_low_pfn;
-#else
-	max_mapnr = max_low_pfn;
-#endif
-	high_memory = (void *) __va(max_low_pfn << PAGE_SHIFT);
-
 	maar_init();
 	memblock_free_all();
 	setup_zero_pages();	/* Setup zeroed pages.  */
@@ -529,7 +527,7 @@
 
 static void __init pcpu_fc_free(void *ptr, size_t size)
 {
-	memblock_free_early(__pa(ptr), size);
+	memblock_free(__pa(ptr), size);
 }
 
 void __init setup_per_cpu_areas(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/mm/physaddr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/mm/physaddr.c
@@ -5,6 +5,7 @@
 #include <linux/mmdebug.h>
 #include <linux/mm.h>
 
+#include <asm/addrspace.h>
 #include <asm/sections.h>
 #include <asm/io.h>
 #include <asm/page.h>
@@ -12,15 +13,6 @@
 
 static inline bool __debug_virt_addr_valid(unsigned long x)
 {
-	/* high_memory does not get immediately defined, and there
-	 * are early callers of __pa() against PAGE_OFFSET
-	 */
-	if (!high_memory && x >= PAGE_OFFSET)
-		return true;
-
-	if (high_memory && x >= PAGE_OFFSET && x < (unsigned long)high_memory)
-		return true;
-
 	/*
 	 * MAX_DMA_ADDRESS is a virtual address that may not correspond to an
 	 * actual physical address. Enough code relies on
@@ -30,7 +22,9 @@
 	if (x == MAX_DMA_ADDRESS)
 		return true;
 
-	return false;
+	return x >= PAGE_OFFSET && (KSEGX(x) < KSEG2 ||
+	       IS_ENABLED(CONFIG_EVA) ||
+	       !IS_ENABLED(CONFIG_HIGHMEM));
 }
 
 phys_addr_t __virt_to_phys(volatile const void *x)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/mm/tlbex.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/mm/tlbex.c
@@ -634,7 +634,7 @@
 		return;
 	}
 
-	if (cpu_has_rixi && !!_PAGE_NO_EXEC) {
+	if (cpu_has_rixi && _PAGE_NO_EXEC != 0) {
 		if (fill_includes_sw_bits) {
 			UASM_i_ROTR(p, reg, reg, ilog2(_PAGE_GLOBAL));
 		} else {
@@ -2167,16 +2167,14 @@
 		uasm_i_tlbr(&p);
 
 		switch (current_cpu_type()) {
-		default:
-			if (cpu_has_mips_r2_exec_hazard) {
-				uasm_i_ehb(&p);
-			fallthrough;
-
 		case CPU_CAVIUM_OCTEON:
 		case CPU_CAVIUM_OCTEON_PLUS:
 		case CPU_CAVIUM_OCTEON2:
-				break;
-			}
+			break;
+		default:
+			if (cpu_has_mips_r2_exec_hazard)
+				uasm_i_ehb(&p);
+			break;
 		}
 
 		/* Examine  entrylo 0 or 1 based on ptr. */
@@ -2243,15 +2241,14 @@
 		uasm_i_tlbr(&p);
 
 		switch (current_cpu_type()) {
-		default:
-			if (cpu_has_mips_r2_exec_hazard) {
-				uasm_i_ehb(&p);
-
 		case CPU_CAVIUM_OCTEON:
 		case CPU_CAVIUM_OCTEON_PLUS:
 		case CPU_CAVIUM_OCTEON2:
-				break;
-			}
+			break;
+		default:
+			if (cpu_has_mips_r2_exec_hazard)
+				uasm_i_ehb(&p);
+			break;
 		}
 
 		/* Examine  entrylo 0 or 1 based on ptr. */
@@ -2576,7 +2573,7 @@
 	unsigned long entry;
 	unsigned pabits, fillbits;
 
-	if (!cpu_has_rixi || !_PAGE_NO_EXEC) {
+	if (!cpu_has_rixi || _PAGE_NO_EXEC == 0) {
 		/*
 		 * We'll only be making use of the fact that we can rotate bits
 		 * into the fill if the CPU supports RIXI, so don't bother
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/pci/ops-rc32434.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/pci/ops-rc32434.c
@@ -112,8 +112,8 @@
 	 * gives them time to settle
 	 */
 	if (where == PCI_VENDOR_ID) {
-		if (ret == 0xffffffff || ret == 0x00000000 ||
-		    ret == 0x0000ffff || ret == 0xffff0000) {
+		if (*val == 0xffffffff || *val == 0x00000000 ||
+		    *val == 0x0000ffff || *val == 0xffff0000) {
 			if (delay > 4)
 				return 0;
 			delay *= 2;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/pci/pcie-octeon.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/pci/pcie-octeon.c
@@ -230,12 +230,18 @@
 {
 	union cvmx_pcie_address pcie_addr;
 	union cvmx_pciercx_cfg006 pciercx_cfg006;
+	union cvmx_pciercx_cfg032 pciercx_cfg032;
 
 	pciercx_cfg006.u32 =
 	    cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG006(pcie_port));
 	if ((bus <= pciercx_cfg006.s.pbnum) && (dev != 0))
 		return 0;
 
+	pciercx_cfg032.u32 =
+		cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+	if ((pciercx_cfg032.s.dlla == 0) || (pciercx_cfg032.s.lt == 1))
+		return 0;
+
 	pcie_addr.u64 = 0;
 	pcie_addr.config.upper = 2;
 	pcie_addr.config.io = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/pic32/pic32mzda/early_console.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/pic32/pic32mzda/early_console.c
@@ -27,7 +27,7 @@
 #define U_BRG(x)	(UART_BASE(x) + 0x40)
 
 static void __iomem *uart_base;
-static char console_port = -1;
+static int console_port = -1;
 
 static int __init configure_uart_pins(int port)
 {
@@ -47,7 +47,7 @@
 	return 0;
 }
 
-static void __init configure_uart(char port, int baud)
+static void __init configure_uart(int port, int baud)
 {
 	u32 pbclk;
 
@@ -60,7 +60,7 @@
 		     uart_base + PIC32_SET(U_STA(port)));
 }
 
-static void __init setup_early_console(char port, int baud)
+static void __init setup_early_console(int port, int baud)
 {
 	if (configure_uart_pins(port))
 		return;
@@ -130,16 +130,15 @@
 	return baud;
 }
 
-void __init fw_init_early_console(char port)
+void __init fw_init_early_console(void)
 {
 	char *arch_cmdline = pic32_getcmdline();
-	int baud = -1;
+	int baud, port;
 
 	uart_base = ioremap(PIC32_BASE_UART, 0xc00);
 
 	baud = get_baud_from_cmdline(arch_cmdline);
-	if (port == -1)
-		port = get_port_from_cmdline(arch_cmdline);
+	port = get_port_from_cmdline(arch_cmdline);
 
 	if (port == -1)
 		port = EARLY_CONSOLE_PORT;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/pic32/pic32mzda/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/pic32/pic32mzda/init.c
@@ -47,7 +47,7 @@
 		strlcpy(arcs_cmdline, boot_command_line, COMMAND_LINE_SIZE);
 
 #ifdef CONFIG_EARLY_PRINTK
-	fw_init_early_console(-1);
+	fw_init_early_console();
 #endif
 	pic32_config_init();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/ralink/ill_acc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/ralink/ill_acc.c
@@ -61,6 +61,7 @@
 	pdev = of_find_device_by_node(np);
 	if (!pdev) {
 		pr_err("%pOFn: failed to lookup pdev\n", np);
+		of_node_put(np);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/ralink/mt7621.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/ralink/mt7621.c
@@ -20,31 +20,42 @@
 
 #include "common.h"
 
-static void *detect_magic __initdata = detect_memory_region;
+#define MT7621_MEM_TEST_PATTERN         0xaa5555aa
+
+static u32 detect_magic __initdata;
+static struct ralink_soc_info *soc_info_ptr;
 
 phys_addr_t mips_cpc_default_phys_base(void)
 {
 	panic("Cannot detect cpc address");
 }
 
+static bool __init mt7621_addr_wraparound_test(phys_addr_t size)
+{
+	void *dm = (void *)KSEG1ADDR(&detect_magic);
+
+	if (CPHYSADDR(dm + size) >= MT7621_LOWMEM_MAX_SIZE)
+		return true;
+	__raw_writel(MT7621_MEM_TEST_PATTERN, dm);
+	if (__raw_readl(dm) != __raw_readl(dm + size))
+		return false;
+	__raw_writel(~MT7621_MEM_TEST_PATTERN, dm);
+	return __raw_readl(dm) == __raw_readl(dm + size);
+}
+
 static void __init mt7621_memory_detect(void)
 {
-	void *dm = &detect_magic;
 	phys_addr_t size;
 
-	for (size = 32 * SZ_1M; size < 256 * SZ_1M; size <<= 1) {
-		if (!__builtin_memcmp(dm, dm + size, sizeof(detect_magic)))
-			break;
+	for (size = 32 * SZ_1M; size <= 256 * SZ_1M; size <<= 1) {
+		if (mt7621_addr_wraparound_test(size)) {
+			memblock_add(MT7621_LOWMEM_BASE, size);
+			return;
+		}
 	}
 
-	if ((size == 256 * SZ_1M) &&
-	    (CPHYSADDR(dm + size) < MT7621_LOWMEM_MAX_SIZE) &&
-	    __builtin_memcmp(dm, dm + size, sizeof(detect_magic))) {
-		memblock_add(MT7621_LOWMEM_BASE, MT7621_LOWMEM_MAX_SIZE);
-		memblock_add(MT7621_HIGHMEM_BASE, MT7621_HIGHMEM_SIZE);
-	} else {
-		memblock_add(MT7621_LOWMEM_BASE, size);
-	}
+	memblock_add(MT7621_LOWMEM_BASE, MT7621_LOWMEM_MAX_SIZE);
+	memblock_add(MT7621_HIGHMEM_BASE, MT7621_HIGHMEM_SIZE);
 }
 
 void __init ralink_of_remap(void)
@@ -56,41 +67,83 @@
 		panic("Failed to remap core resources");
 }
 
-static void soc_dev_init(struct ralink_soc_info *soc_info, u32 rev)
+static unsigned int __init mt7621_get_soc_name0(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME0);
+}
+
+static unsigned int __init mt7621_get_soc_name1(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME1);
+}
+
+static bool __init mt7621_soc_valid(void)
+{
+	if (mt7621_get_soc_name0() == MT7621_CHIP_NAME0 &&
+			mt7621_get_soc_name1() == MT7621_CHIP_NAME1)
+		return true;
+	else
+		return false;
+}
+
+static const char __init *mt7621_get_soc_id(void)
+{
+	if (mt7621_soc_valid())
+		return "MT7621";
+	else
+		return "invalid";
+}
+
+static unsigned int __init mt7621_get_soc_rev(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_REV);
+}
+
+static unsigned int __init mt7621_get_soc_ver(void)
+{
+	return (mt7621_get_soc_rev() >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK;
+}
+
+static unsigned int __init mt7621_get_soc_eco(void)
+{
+	return (mt7621_get_soc_rev() & CHIP_REV_ECO_MASK);
+}
+
+static const char __init *mt7621_get_soc_revision(void)
+{
+	if (mt7621_get_soc_rev() == 1 && mt7621_get_soc_eco() == 1)
+		return "E2";
+	else
+		return "E1";
+}
+
+static int __init mt7621_soc_dev_init(void)
 {
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
-		return;
+		return -ENOMEM;
 
 	soc_dev_attr->soc_id = "mt7621";
 	soc_dev_attr->family = "Ralink";
+	soc_dev_attr->revision = mt7621_get_soc_revision();
 
-	if (((rev >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK) == 1 &&
-	    (rev & CHIP_REV_ECO_MASK) == 1)
-		soc_dev_attr->revision = "E2";
-	else
-		soc_dev_attr->revision = "E1";
-
-	soc_dev_attr->data = soc_info;
+	soc_dev_attr->data = soc_info_ptr;
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev)) {
 		kfree(soc_dev_attr);
-		return;
+		return PTR_ERR(soc_dev);
 	}
+
+	return 0;
 }
+device_initcall(mt7621_soc_dev_init);
 
 void __init prom_soc_init(struct ralink_soc_info *soc_info)
 {
-	void __iomem *sysc = (void __iomem *) KSEG1ADDR(MT7621_SYSC_BASE);
-	unsigned char *name = NULL;
-	u32 n0;
-	u32 n1;
-	u32 rev;
-
 	/* Early detection of CMP support */
 	mips_cm_probe();
 	mips_cpc_probe();
@@ -113,27 +166,23 @@
 		__sync();
 	}
 
-	n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
-	n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
-
-	if (n0 == MT7621_CHIP_NAME0 && n1 == MT7621_CHIP_NAME1) {
-		name = "MT7621";
+	if (mt7621_soc_valid())
 		soc_info->compatible = "mediatek,mt7621-soc";
-	} else {
-		panic("mt7621: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
-	}
+	else
+		panic("mt7621: unknown SoC, n0:%08x n1:%08x\n",
+				mt7621_get_soc_name0(),
+				mt7621_get_soc_name1());
 	ralink_soc = MT762X_SOC_MT7621AT;
-	rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
 
 	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
 		"MediaTek %s ver:%u eco:%u",
-		name,
-		(rev >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK,
-		(rev & CHIP_REV_ECO_MASK));
+		mt7621_get_soc_id(),
+		mt7621_get_soc_ver(),
+		mt7621_get_soc_eco());
 
 	soc_info->mem_detect = mt7621_memory_detect;
 
-	soc_dev_init(soc_info, rev);
+	soc_info_ptr = soc_info;
 
 	if (!register_cps_smp_ops())
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/rb532/devices.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/rb532/devices.c
@@ -301,11 +301,9 @@
 static int __init setup_kmac(char *s)
 {
 	printk(KERN_INFO "korina mac = %s\n", s);
-	if (!mac_pton(s, korina_dev0_data.mac)) {
+	if (!mac_pton(s, korina_dev0_data.mac))
 		printk(KERN_ERR "Invalid mac\n");
-		return -EINVAL;
-	}
-	return 0;
+	return 1;
 }
 
 __setup("kmac=", setup_kmac);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/sgi-ip27/ip27-memory.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/sgi-ip27/ip27-memory.c
@@ -341,7 +341,8 @@
 				continue;
 			}
 			memblock_add_node(PFN_PHYS(slot_getbasepfn(node, slot)),
-					  PFN_PHYS(slot_psize), node);
+					  PFN_PHYS(slot_psize), node,
+					  MEMBLOCK_NONE);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/sgi-ip27/ip27-xtalk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/sgi-ip27/ip27-xtalk.c
@@ -27,15 +27,18 @@
 {
 	struct xtalk_bridge_platform_data *bd;
 	struct sgi_w1_platform_data *wd;
-	struct platform_device *pdev;
+	struct platform_device *pdev_wd;
+	struct platform_device *pdev_bd;
 	struct resource w1_res;
 	unsigned long offset;
 
 	offset = NODE_OFFSET(nasid);
 
 	wd = kzalloc(sizeof(*wd), GFP_KERNEL);
-	if (!wd)
-		goto no_mem;
+	if (!wd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		return;
+	}
 
 	snprintf(wd->dev_id, sizeof(wd->dev_id), "bridge-%012lx",
 		 offset + (widget << SWIN_SIZE_BITS));
@@ -46,22 +49,35 @@
 	w1_res.end = w1_res.start + 3;
 	w1_res.flags = IORESOURCE_MEM;
 
-	pdev = platform_device_alloc("sgi_w1", PLATFORM_DEVID_AUTO);
-	if (!pdev) {
-		kfree(wd);
-		goto no_mem;
-	}
-	platform_device_add_resources(pdev, &w1_res, 1);
-	platform_device_add_data(pdev, wd, sizeof(*wd));
-	platform_device_add(pdev);
+	pdev_wd = platform_device_alloc("sgi_w1", PLATFORM_DEVID_AUTO);
+	if (!pdev_wd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		goto err_kfree_wd;
+	}
+	if (platform_device_add_resources(pdev_wd, &w1_res, 1)) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform resources.\n", nasid, widget);
+		goto err_put_pdev_wd;
+	}
+	if (platform_device_add_data(pdev_wd, wd, sizeof(*wd))) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform data.\n", nasid, widget);
+		goto err_put_pdev_wd;
+	}
+	if (platform_device_add(pdev_wd)) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform device.\n", nasid, widget);
+		goto err_put_pdev_wd;
+	}
+	/* platform_device_add_data() duplicates the data */
+	kfree(wd);
 
 	bd = kzalloc(sizeof(*bd), GFP_KERNEL);
-	if (!bd)
-		goto no_mem;
-	pdev = platform_device_alloc("xtalk-bridge", PLATFORM_DEVID_AUTO);
-	if (!pdev) {
-		kfree(bd);
-		goto no_mem;
+	if (!bd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		goto err_unregister_pdev_wd;
+	}
+	pdev_bd = platform_device_alloc("xtalk-bridge", PLATFORM_DEVID_AUTO);
+	if (!pdev_bd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		goto err_kfree_bd;
 	}
 
 
@@ -82,13 +98,31 @@
 	bd->io.flags	= IORESOURCE_IO;
 	bd->io_offset	= offset;
 
-	platform_device_add_data(pdev, bd, sizeof(*bd));
-	platform_device_add(pdev);
+	if (platform_device_add_data(pdev_bd, bd, sizeof(*bd))) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform data.\n", nasid, widget);
+		goto err_put_pdev_bd;
+	}
+	if (platform_device_add(pdev_bd)) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform device.\n", nasid, widget);
+		goto err_put_pdev_bd;
+	}
+	/* platform_device_add_data() duplicates the data */
+	kfree(bd);
 	pr_info("xtalk:n%d/%x bridge widget\n", nasid, widget);
 	return;
 
-no_mem:
-	pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+err_put_pdev_bd:
+	platform_device_put(pdev_bd);
+err_kfree_bd:
+	kfree(bd);
+err_unregister_pdev_wd:
+	platform_device_unregister(pdev_wd);
+	return;
+err_put_pdev_wd:
+	platform_device_put(pdev_wd);
+err_kfree_wd:
+	kfree(wd);
+	return;
 }
 
 static int probe_one_port(nasid_t nasid, int widget, int masterwid)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/sgi-ip30/ip30-console.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/sgi-ip30/ip30-console.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 
 #include <linux/io.h>
+#include <linux/processor.h>
 
 #include <asm/sn/ioc3.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/sni/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/sni/time.c
@@ -18,14 +18,14 @@
 {
 	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 12) = 0x34;
 	wmb();
-	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 0) = SNI_COUNTER0_DIV;
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 0) = SNI_COUNTER0_DIV & 0xff;
 	wmb();
 	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 0) = SNI_COUNTER0_DIV >> 8;
 	wmb();
 
 	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 12) = 0xb4;
 	wmb();
-	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 8) = SNI_COUNTER2_DIV;
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 8) = SNI_COUNTER2_DIV & 0xff;
 	wmb();
 	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 8) = SNI_COUNTER2_DIV >> 8;
 	wmb();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/vdso/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/vdso/Makefile
@@ -68,7 +68,7 @@
 
 # Check that we don't have PIC 'jalr t9' calls left
 quiet_cmd_vdso_mips_check = VDSOCHK $@
-      cmd_vdso_mips_check = if $(OBJDUMP) --disassemble $@ | egrep -h "jalr.*t9" > /dev/null; \
+      cmd_vdso_mips_check = if $(OBJDUMP) --disassemble $@ | grep -E -h "jalr.*t9" > /dev/null; \
 		       then (echo >&2 "$@: PIC 'jalr t9' calls are not supported"; \
 			     rm -f $@; /bin/false); fi
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/mips/vr41xx/common/icu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/mips/vr41xx/common/icu.c
@@ -640,8 +640,6 @@
 
 	printk(KERN_ERR "spurious ICU interrupt: %04x,%04x\n", pend1, pend2);
 
-	atomic_inc(&irq_err_count);
-
 	return -1;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nds32/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/nds32/include/asm/uaccess.h
@@ -70,9 +70,7 @@
  * versions are void (ie, don't return a value as such).
  */
 
-#define get_user	__get_user					\
-
-#define __get_user(x, ptr)						\
+#define get_user(x, ptr)						\
 ({									\
 	long __gu_err = 0;						\
 	__get_user_check((x), (ptr), __gu_err);				\
@@ -85,6 +83,14 @@
 	(void)0;							\
 })
 
+#define __get_user(x, ptr)						\
+({									\
+	long __gu_err = 0;						\
+	const __typeof__(*(ptr)) __user *__p = (ptr);			\
+	__get_user_err((x), __p, (__gu_err));				\
+	__gu_err;							\
+})
+
 #define __get_user_check(x, ptr, err)					\
 ({									\
 	const __typeof__(*(ptr)) __user *__p = (ptr);			\
@@ -165,12 +171,18 @@
 		: "r"(addr), "i"(-EFAULT)				\
 		: "cc")
 
-#define put_user	__put_user					\
+#define put_user(x, ptr)						\
+({									\
+	long __pu_err = 0;						\
+	__put_user_check((x), (ptr), __pu_err);				\
+	__pu_err;							\
+})
 
 #define __put_user(x, ptr)						\
 ({									\
 	long __pu_err = 0;						\
-	__put_user_err((x), (ptr), __pu_err);				\
+	__typeof__(*(ptr)) __user *__p = (ptr);				\
+	__put_user_err((x), __p, __pu_err);				\
 	__pu_err;							\
 })
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nds32/kernel/fpu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/nds32/kernel/fpu.c
@@ -223,7 +223,7 @@
 		}
 	} else if (fpcsr & FPCSR_mskRIT) {
 		if (!user_mode(regs))
-			do_exit(SIGILL);
+			make_task_dead(SIGILL);
 		si_signo = SIGILL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nds32/kernel/perf_event_cpu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/nds32/kernel/perf_event_cpu.c
@@ -1363,6 +1363,7 @@
 perf_callchain_user(struct perf_callchain_entry_ctx *entry,
 		    struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	unsigned long fp = 0;
 	unsigned long gp = 0;
 	unsigned long lp = 0;
@@ -1371,7 +1372,7 @@
 
 	leaf_fp = 0;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -1479,9 +1480,10 @@
 perf_callchain_kernel(struct perf_callchain_entry_ctx *entry,
 		      struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct stackframe fr;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -1493,20 +1495,23 @@
 
 unsigned long perf_instruction_pointer(struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
+
 	/* However, NDS32 does not support virtualization */
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
-		return perf_guest_cbs->get_guest_ip();
+	if (guest_cbs && guest_cbs->is_in_guest())
+		return guest_cbs->get_guest_ip();
 
 	return instruction_pointer(regs);
 }
 
 unsigned long perf_misc_flags(struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	int misc = 0;
 
 	/* However, NDS32 does not support virtualization */
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		if (perf_guest_cbs->is_user_mode())
+	if (guest_cbs && guest_cbs->is_in_guest()) {
+		if (guest_cbs->is_user_mode())
 			misc |= PERF_RECORD_MISC_GUEST_USER;
 		else
 			misc |= PERF_RECORD_MISC_GUEST_KERNEL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nds32/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/nds32/kernel/traps.c
@@ -141,7 +141,7 @@
 
 	bust_spinlocks(0);
 	spin_unlock_irq(&die_lock);
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 EXPORT_SYMBOL(die);
@@ -240,7 +240,7 @@
 	pr_emerg("unhandled_interruption\n");
 	show_regs(regs);
 	if (!user_mode(regs))
-		do_exit(SIGKILL);
+		make_task_dead(SIGKILL);
 	force_sig(SIGKILL);
 }
 
@@ -251,7 +251,7 @@
 		 addr, type);
 	show_regs(regs);
 	if (!user_mode(regs))
-		do_exit(SIGKILL);
+		make_task_dead(SIGKILL);
 	force_sig(SIGKILL);
 }
 
@@ -278,7 +278,7 @@
 	pr_emerg("Reserved Instruction\n");
 	show_regs(regs);
 	if (!user_mode(regs))
-		do_exit(SIGILL);
+		make_task_dead(SIGILL);
 	force_sig(SIGILL);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/boot/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/boot/Makefile
@@ -20,7 +20,7 @@
 $(obj)/vmlinux.gz: $(obj)/vmlinux.bin FORCE
 	$(call if_changed,gzip)
 
-$(obj)/vmImage: $(obj)/vmlinux.gz
+$(obj)/vmImage: $(obj)/vmlinux.gz FORCE
 	$(call if_changed,uimage)
 	@$(kecho) 'Kernel: $@ is ready'
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/boot/dts/10m50_devboard.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/boot/dts/10m50_devboard.dts
@@ -97,7 +97,7 @@
 			rx-fifo-depth = <8192>;
 			tx-fifo-depth = <8192>;
 			address-bits = <48>;
-			max-frame-size = <1518>;
+			max-frame-size = <1500>;
 			local-mac-address = [00 00 00 00 00 00];
 			altr,has-supplementary-unicast;
 			altr,enable-sup-addr = <1>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/boot/dts/3c120_devboard.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/boot/dts/3c120_devboard.dts
@@ -106,7 +106,7 @@
 				interrupt-names = "rx_irq", "tx_irq";
 				rx-fifo-depth = <8192>;
 				tx-fifo-depth = <8192>;
-				max-frame-size = <1518>;
+				max-frame-size = <1500>;
 				local-mac-address = [ 00 00 00 00 00 00 ];
 				phy-mode = "rgmii-id";
 				phy-handle = <&phy0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/include/asm/entry.h
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/include/asm/entry.h
@@ -50,7 +50,8 @@
 	stw	r13, PT_R13(sp)
 	stw	r14, PT_R14(sp)
 	stw	r15, PT_R15(sp)
-	stw	r2, PT_ORIG_R2(sp)
+	movi	r24, -1
+	stw	r24, PT_ORIG_R2(sp)
 	stw	r7, PT_ORIG_R7(sp)
 
 	stw	ra, PT_RA(sp)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/include/asm/ptrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/include/asm/ptrace.h
@@ -74,6 +74,8 @@
 	((struct pt_regs *)((unsigned long)current_thread_info() + THREAD_SIZE)\
 		- 1)
 
+#define force_successful_syscall_return() (current_pt_regs()->orig_r2 = -1)
+
 int do_syscall_trace_enter(void);
 void do_syscall_trace_exit(void);
 #endif /* __ASSEMBLY__ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/include/asm/timex.h
@@ -8,5 +8,8 @@
 typedef unsigned long cycles_t;
 
 extern cycles_t get_cycles(void);
+#define get_cycles get_cycles
+
+#define random_get_entropy() (((unsigned long)get_cycles()) ?: random_get_entropy_fallback())
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/include/asm/uaccess.h
@@ -88,6 +88,7 @@
 /* Optimized macros */
 #define __get_user_asm(val, insn, addr, err)				\
 {									\
+	unsigned long __gu_val;						\
 	__asm__ __volatile__(						\
 	"       movi    %0, %3\n"					\
 	"1:   " insn " %1, 0(%2)\n"					\
@@ -96,14 +97,20 @@
 	"       .section __ex_table,\"a\"\n"				\
 	"       .word 1b, 2b\n"						\
 	"       .previous"						\
-	: "=&r" (err), "=r" (val)					\
+	: "=&r" (err), "=r" (__gu_val)					\
 	: "r" (addr), "i" (-EFAULT));					\
+	val = (__force __typeof__(*(addr)))__gu_val;			\
 }
 
-#define __get_user_unknown(val, size, ptr, err) do {			\
+extern void __get_user_unknown(void);
+
+#define __get_user_8(val, ptr, err) do {				\
+	u64 __val = 0;							\
 	err = 0;							\
-	if (__copy_from_user(&(val), ptr, size)) {			\
+	if (raw_copy_from_user(&(__val), ptr, sizeof(val))) {		\
 		err = -EFAULT;						\
+	} else {							\
+		val = (typeof(val))(typeof((val) - (val)))__val;	\
 	}								\
 	} while (0)
 
@@ -119,8 +126,11 @@
 	case 4:								\
 		__get_user_asm(val, "ldw", ptr, err);			\
 		break;							\
+	case 8:								\
+		__get_user_8(val, ptr, err);				\
+		break;							\
 	default:							\
-		__get_user_unknown(val, size, ptr, err);		\
+		__get_user_unknown();					\
 		break;							\
 	}								\
 } while (0)
@@ -129,9 +139,7 @@
 	({								\
 	long __gu_err = -EFAULT;					\
 	const __typeof__(*(ptr)) __user *__gu_ptr = (ptr);		\
-	unsigned long __gu_val = 0;					\
-	__get_user_common(__gu_val, sizeof(*(ptr)), __gu_ptr, __gu_err);\
-	(x) = (__force __typeof__(x))__gu_val;				\
+	__get_user_common(x, sizeof(*(ptr)), __gu_ptr, __gu_err);	\
 	__gu_err;							\
 	})
 
@@ -139,11 +147,9 @@
 ({									\
 	long __gu_err = -EFAULT;					\
 	const __typeof__(*(ptr)) __user *__gu_ptr = (ptr);		\
-	unsigned long __gu_val = 0;					\
 	if (access_ok( __gu_ptr, sizeof(*__gu_ptr)))	\
-		__get_user_common(__gu_val, sizeof(*__gu_ptr),		\
+		__get_user_common(x, sizeof(*__gu_ptr),			\
 			__gu_ptr, __gu_err);				\
-	(x) = (__force __typeof__(x))__gu_val;				\
 	__gu_err;							\
 })
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/kernel/entry.S
@@ -185,6 +185,7 @@
 	ldw	r5, PT_R5(sp)
 
 local_restart:
+	stw	r2, PT_ORIG_R2(sp)
 	/* Check that the requested system call is within limits */
 	movui	r1, __NR_syscalls
 	bgeu	r2, r1, ret_invsyscall
@@ -192,7 +193,6 @@
 	movhi	r11, %hiadj(sys_call_table)
 	add	r1, r1, r11
 	ldw	r1, %lo(sys_call_table)(r1)
-	beq	r1, r0, ret_invsyscall
 
 	/* Check if we are being traced */
 	GET_THREAD_INFO r11
@@ -213,6 +213,9 @@
 translate_rc_and_ret:
 	movi	r1, 0
 	bge	r2, zero, 3f
+	ldw	r1, PT_ORIG_R2(sp)
+	addi	r1, r1, 1
+	beq	r1, zero, 3f
 	sub	r2, zero, r2
 	movi	r1, 1
 3:
@@ -255,9 +258,9 @@
 	ldw	r6, PT_R6(sp)
 	ldw	r7, PT_R7(sp)
 
-	/* Fetch the syscall function, we don't need to check the boundaries
-	 * since this is already done.
-	 */
+	/* Fetch the syscall function. */
+	movui	r1, __NR_syscalls
+	bgeu	r2, r1, traced_invsyscall
 	slli	r1, r2, 2
 	movhi	r11,%hiadj(sys_call_table)
 	add	r1, r1, r11
@@ -276,6 +279,9 @@
 translate_rc_and_ret2:
 	movi	r1, 0
 	bge	r2, zero, 4f
+	ldw	r1, PT_ORIG_R2(sp)
+	addi	r1, r1, 1
+	beq	r1, zero, 4f
 	sub	r2, zero, r2
 	movi	r1, 1
 4:
@@ -287,6 +293,11 @@
 	RESTORE_SWITCH_STACK
 	br	ret_from_exception
 
+	/* If the syscall number was invalid return ENOSYS */
+traced_invsyscall:
+	movi	r2, -ENOSYS
+	br	translate_rc_and_ret2
+
 Luser_return:
 	GET_THREAD_INFO	r11			/* get thread_info pointer */
 	ldw	r10, TI_FLAGS(r11)		/* get thread_info->flags */
@@ -336,9 +347,6 @@
 	/* skip if no interrupt is pending */
 	beq	r12, r0, ret_from_interrupt
 
-	movi	r24, -1
-	stw	r24, PT_ORIG_R2(sp)
-
 	/*
 	 * Process an external hardware interrupt.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/kernel/signal.c
@@ -36,10 +36,10 @@
 
 static inline int rt_restore_ucontext(struct pt_regs *regs,
 					struct switch_stack *sw,
-					struct ucontext *uc, int *pr2)
+					struct ucontext __user *uc, int *pr2)
 {
 	int temp;
-	unsigned long *gregs = uc->uc_mcontext.gregs;
+	unsigned long __user *gregs = uc->uc_mcontext.gregs;
 	int err;
 
 	/* Always make any pending restarted system calls return -EINTR */
@@ -102,10 +102,11 @@
 {
 	struct pt_regs *regs = (struct pt_regs *)(sw + 1);
 	/* Verify, can we follow the stack back */
-	struct rt_sigframe *frame = (struct rt_sigframe *) regs->sp;
+	struct rt_sigframe __user *frame;
 	sigset_t set;
 	int rval;
 
+	frame = (struct rt_sigframe __user *) regs->sp;
 	if (!access_ok(frame, sizeof(*frame)))
 		goto badframe;
 
@@ -124,10 +125,10 @@
 	return 0;
 }
 
-static inline int rt_setup_ucontext(struct ucontext *uc, struct pt_regs *regs)
+static inline int rt_setup_ucontext(struct ucontext __user *uc, struct pt_regs *regs)
 {
 	struct switch_stack *sw = (struct switch_stack *)regs - 1;
-	unsigned long *gregs = uc->uc_mcontext.gregs;
+	unsigned long __user *gregs = uc->uc_mcontext.gregs;
 	int err = 0;
 
 	err |= __put_user(MCONTEXT_VERSION, &uc->uc_mcontext.version);
@@ -162,8 +163,9 @@
 	return err;
 }
 
-static inline void *get_sigframe(struct ksignal *ksig, struct pt_regs *regs,
-				 size_t frame_size)
+static inline void __user *get_sigframe(struct ksignal *ksig,
+					struct pt_regs *regs,
+					size_t frame_size)
 {
 	unsigned long usp;
 
@@ -174,13 +176,13 @@
 	usp = sigsp(usp, ksig);
 
 	/* Verify, is it 32 or 64 bit aligned */
-	return (void *)((usp - frame_size) & -8UL);
+	return (void __user *)((usp - frame_size) & -8UL);
 }
 
 static int setup_rt_frame(struct ksignal *ksig, sigset_t *set,
 			  struct pt_regs *regs)
 {
-	struct rt_sigframe *frame;
+	struct rt_sigframe __user *frame;
 	int err = 0;
 
 	frame = get_sigframe(ksig, regs, sizeof(*frame));
@@ -240,7 +242,7 @@
 	/*
 	 * If we were from a system call, check for system call restarting...
 	 */
-	if (regs->orig_r2 >= 0) {
+	if (regs->orig_r2 >= 0 && regs->r1) {
 		continue_addr = regs->ea;
 		restart_addr = continue_addr - 4;
 		retval = regs->r2;
@@ -262,6 +264,7 @@
 			regs->ea = restart_addr;
 			break;
 		}
+		regs->orig_r2 = -1;
 	}
 
 	if (get_signal(&ksig)) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/kernel/syscall_table.c
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/kernel/syscall_table.c
@@ -13,5 +13,6 @@
 #define __SYSCALL(nr, call) [nr] = (call),
 
 void *sys_call_table[__NR_syscalls] = {
+	[0 ... __NR_syscalls-1] = sys_ni_syscall,
 #include <asm/unistd.h>
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/nios2/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/nios2/kernel/traps.c
@@ -37,10 +37,10 @@
 	show_regs(regs);
 	spin_unlock_irq(&die_lock);
 	/*
-	 * do_exit() should take care of panic'ing from an interrupt
+	 * make_task_dead() should take care of panic'ing from an interrupt
 	 * context so we don't handle it here
 	 */
-	do_exit(err);
+	make_task_dead(err);
 }
 
 void _exception(int signo, struct pt_regs *regs, int code, unsigned long addr)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/include/asm/io.h
@@ -31,7 +31,7 @@
 void __iomem *ioremap(phys_addr_t offset, unsigned long size);
 
 #define iounmap iounmap
-extern void iounmap(void __iomem *addr);
+extern void iounmap(volatile void __iomem *addr);
 
 #include <asm-generic/io.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/include/asm/syscalls.h
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/include/asm/syscalls.h
@@ -22,9 +22,11 @@
 
 asmlinkage long __sys_clone(unsigned long clone_flags, unsigned long newsp,
 			void __user *parent_tid, void __user *child_tid, int tls);
+asmlinkage long __sys_clone3(struct clone_args __user *uargs, size_t size);
 asmlinkage long __sys_fork(void);
 
 #define sys_clone __sys_clone
+#define sys_clone3 __sys_clone3
 #define sys_fork __sys_fork
 
 #endif /* __ASM_OPENRISC_SYSCALLS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/include/asm/timex.h
@@ -23,6 +23,7 @@
 {
 	return mfspr(SPR_TTCR);
 }
+#define get_cycles get_cycles
 
 /* This isn't really used any more */
 #define CLOCK_TICK_RATE 1000
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/kernel/dma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/kernel/dma.c
@@ -33,7 +33,7 @@
 	 * Flush the page out of the TLB so that the new page flags get
 	 * picked up next time there's an access
 	 */
-	flush_tlb_page(NULL, addr);
+	flush_tlb_kernel_range(addr, addr + PAGE_SIZE);
 
 	/* Flush page out of dcache */
 	for (cl = __pa(addr); cl < __pa(next); cl += cpuinfo->dcache_block_size)
@@ -56,7 +56,7 @@
 	 * Flush the page out of the TLB so that the new page flags get
 	 * picked up next time there's an access
 	 */
-	flush_tlb_page(NULL, addr);
+	flush_tlb_kernel_range(addr, addr + PAGE_SIZE);
 
 	return 0;
 }
@@ -74,10 +74,10 @@
 	 * We need to iterate through the pages, clearing the dcache for
 	 * them and setting the cache-inhibit bit.
 	 */
-	mmap_read_lock(&init_mm);
-	error = walk_page_range(&init_mm, va, va + size, &set_nocache_walk_ops,
-			NULL);
-	mmap_read_unlock(&init_mm);
+	mmap_write_lock(&init_mm);
+	error = walk_page_range_novma(&init_mm, va, va + size,
+			&set_nocache_walk_ops, NULL, NULL);
+	mmap_write_unlock(&init_mm);
 
 	if (error)
 		return ERR_PTR(error);
@@ -88,11 +88,11 @@
 {
 	unsigned long va = (unsigned long)cpu_addr;
 
-	mmap_read_lock(&init_mm);
+	mmap_write_lock(&init_mm);
 	/* walk_page_range shouldn't be able to fail here */
-	WARN_ON(walk_page_range(&init_mm, va, va + size,
-			&clear_nocache_walk_ops, NULL));
-	mmap_read_unlock(&init_mm);
+	WARN_ON(walk_page_range_novma(&init_mm, va, va + size,
+			&clear_nocache_walk_ops, NULL, NULL));
+	mmap_write_unlock(&init_mm);
 }
 
 void arch_sync_dma_for_device(phys_addr_t addr, size_t size,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/kernel/entry.S
@@ -173,7 +173,6 @@
 	l.sw    PT_GPR28(r1),r28					;\
 	l.sw    PT_GPR29(r1),r29					;\
 	/* r30 already save */					;\
-/*        l.sw    PT_GPR30(r1),r30*/					;\
 	l.sw    PT_GPR31(r1),r31					;\
 	TRACE_IRQS_OFF_ENTRY						;\
 	/* Store -1 in orig_gpr11 for non-syscall exceptions */	;\
@@ -211,9 +210,8 @@
 	l.sw    PT_GPR27(r1),r27					;\
 	l.sw    PT_GPR28(r1),r28					;\
 	l.sw    PT_GPR29(r1),r29					;\
-	/* r31 already saved */					;\
-	l.sw    PT_GPR30(r1),r30					;\
-/*        l.sw    PT_GPR31(r1),r31	*/				;\
+	/* r30 already saved */						;\
+	l.sw    PT_GPR31(r1),r31					;\
 	/* Store -1 in orig_gpr11 for non-syscall exceptions */	;\
 	l.addi	r30,r0,-1					;\
 	l.sw	PT_ORIG_GPR11(r1),r30				;\
@@ -1170,6 +1168,11 @@
 	l.j	_fork_save_extra_regs_and_call
 	 l.nop
 
+ENTRY(__sys_clone3)
+	l.movhi	r29,hi(sys_clone3)
+	l.j	_fork_save_extra_regs_and_call
+	 l.ori	r29,r29,lo(sys_clone3)
+
 ENTRY(__sys_fork)
 	l.movhi	r29,hi(sys_fork)
 	l.ori	r29,r29,lo(sys_fork)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/kernel/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/kernel/head.S
@@ -521,6 +521,15 @@
 	l.ori	r3,r0,0x1
 	l.mtspr	r0,r3,SPR_SR
 
+	/*
+	 * Start the TTCR as early as possible, so that the RNG can make use of
+	 * measurements of boot time from the earliest opportunity. Especially
+	 * important is that the TTCR does not return zero by the time we reach
+	 * rand_initialize().
+	 */
+	l.movhi r3,hi(SPR_TTMR_CR)
+	l.mtspr r0,r3,SPR_TTMR
+
 	CLEAR_GPR(r1)
 	CLEAR_GPR(r2)
 	CLEAR_GPR(r3)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/kernel/setup.c
@@ -270,6 +270,9 @@
 
 void __init setup_arch(char **cmdline_p)
 {
+	/* setup memblock allocator */
+	setup_memory();
+
 	unflatten_and_copy_device_tree();
 
 	setup_cpuinfo();
@@ -293,9 +296,6 @@
 	}
 #endif
 
-	/* setup memblock allocator */
-	setup_memory();
-
 	/* paging_init() sets up the MMU and marks all pages as reserved */
 	paging_init();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/kernel/smp.c
@@ -272,7 +272,7 @@
 	local_flush_tlb_range(NULL, fd->addr1, fd->addr2);
 }
 
-static void smp_flush_tlb_range(struct cpumask *cmask, unsigned long start,
+static void smp_flush_tlb_range(const struct cpumask *cmask, unsigned long start,
 				unsigned long end)
 {
 	unsigned int cpuid;
@@ -320,7 +320,9 @@
 void flush_tlb_range(struct vm_area_struct *vma,
 		     unsigned long start, unsigned long end)
 {
-	smp_flush_tlb_range(mm_cpumask(vma->vm_mm), start, end);
+	const struct cpumask *cmask = vma ? mm_cpumask(vma->vm_mm)
+					  : cpu_online_mask;
+	smp_flush_tlb_range(cmask, start, end);
 }
 
 /* Instruction cache invalidate - performed on each cpu */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/kernel/traps.c
@@ -212,7 +212,7 @@
 	__asm__ __volatile__("l.nop   1");
 	do {} while (1);
 #endif
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 /* This is normally the 'Oops' routine */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/openrisc/mm/ioremap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/openrisc/mm/ioremap.c
@@ -77,7 +77,7 @@
 }
 EXPORT_SYMBOL(ioremap);
 
-void iounmap(void __iomem *addr)
+void iounmap(volatile void __iomem *addr)
 {
 	/* If the page is from the fixmap pool then we just clear out
 	 * the fixmap mapping.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/Kconfig
@@ -9,8 +9,10 @@
 	select ARCH_WANT_FRAME_POINTERS
 	select ARCH_HAS_ELF_RANDOMIZE
 	select ARCH_HAS_STRICT_KERNEL_RWX
+	select ARCH_HAS_STRICT_MODULE_RWX
 	select ARCH_HAS_UBSAN_SANITIZE_ALL
 	select ARCH_NO_SG_CHAIN
+	select ARCH_SPLIT_ARG64 if !64BIT
 	select ARCH_SUPPORTS_HUGETLBFS if PA20
 	select ARCH_SUPPORTS_MEMORY_FAILURE
 	select DMA_OPS
@@ -141,10 +143,10 @@
 
 choice
 	prompt "Processor type"
-	default PA7000
+	default PA7000 if "$(ARCH)" = "parisc"
 
 config PA7000
-	bool "PA7000/PA7100"
+	bool "PA7000/PA7100" if "$(ARCH)" = "parisc"
 	help
 	  This is the processor type of your CPU.  This information is
 	  used for optimizing purposes.  In order to compile a kernel
@@ -155,21 +157,21 @@
 	  which is required on some machines.
 
 config PA7100LC
-	bool "PA7100LC"
+	bool "PA7100LC" if "$(ARCH)" = "parisc"
 	help
 	  Select this option for the PCX-L processor, as used in the
 	  712, 715/64, 715/80, 715/100, 715/100XC, 725/100, 743, 748,
 	  D200, D210, D300, D310 and E-class
 
 config PA7200
-	bool "PA7200"
+	bool "PA7200" if "$(ARCH)" = "parisc"
 	help
 	  Select this option for the PCX-T' processor, as used in the
 	  C100, C110, J100, J110, J210XC, D250, D260, D350, D360,
 	  K100, K200, K210, K220, K400, K410 and K420
 
 config PA7300LC
-	bool "PA7300LC"
+	bool "PA7300LC" if "$(ARCH)" = "parisc"
 	help
 	  Select this option for the PCX-L2 processor, as used in the
 	  744, A180, B132L, B160L, B180L, C132L, C160L, C180L,
@@ -219,7 +221,8 @@
 	  Enabling this option will probably slow down your kernel.
 
 config 64BIT
-	bool "64-bit kernel"
+	def_bool y if "$(ARCH)" = "parisc64"
+	bool "64-bit kernel" if "$(ARCH)" = "parisc"
 	depends on PA8X00
 	help
 	  Enable this if you want to support 64bit kernel on PA-RISC platform.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/Makefile
@@ -17,7 +17,12 @@
 # Mike Shaver, Helge Deller and Martin K. Petersen
 #
 
+ifdef CONFIG_PARISC_SELF_EXTRACT
+boot := arch/parisc/boot
+KBUILD_IMAGE := $(boot)/bzImage
+else
 KBUILD_IMAGE := vmlinuz
+endif
 
 NM		= sh $(srctree)/arch/parisc/nm
 CHECKFLAGS	+= -D__hppa__=1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/assembly.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/assembly.h
@@ -72,10 +72,6 @@
 
 #include <asm/asmregs.h>
 
-	sp	=	30
-	gp	=	27
-	ipsw	=	22
-
 	/*
 	 * We provide two versions of each macro to convert from physical
 	 * to virtual and vice versa. The "_r1" versions take one argument
@@ -83,26 +79,28 @@
 	 * version takes two arguments: a src and destination register.
 	 * However, the source and destination registers can not be
 	 * the same register.
+	 *
+	 * We use add,l to avoid clobbering the C/B bits in the PSW.
 	 */
 
 	.macro  tophys  grvirt, grphys
-	ldil    L%(__PAGE_OFFSET), \grphys
-	sub     \grvirt, \grphys, \grphys
+	ldil    L%(-__PAGE_OFFSET), \grphys
+	addl    \grvirt, \grphys, \grphys
 	.endm
-	
+
 	.macro  tovirt  grphys, grvirt
 	ldil    L%(__PAGE_OFFSET), \grvirt
-	add     \grphys, \grvirt, \grvirt
+	addl    \grphys, \grvirt, \grvirt
 	.endm
 
 	.macro  tophys_r1  gr
-	ldil    L%(__PAGE_OFFSET), %r1
-	sub     \gr, %r1, \gr
+	ldil    L%(-__PAGE_OFFSET), %r1
+	addl    \gr, %r1, \gr
 	.endm
-	
+
 	.macro  tovirt_r1  gr
 	ldil    L%(__PAGE_OFFSET), %r1
-	add     \gr, %r1, \gr
+	addl    \gr, %r1, \gr
 	.endm
 
 	.macro delay value
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/cacheflush.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/cacheflush.h
@@ -53,6 +53,11 @@
 
 #define flush_dcache_mmap_lock(mapping)		xa_lock_irq(&mapping->i_pages)
 #define flush_dcache_mmap_unlock(mapping)	xa_unlock_irq(&mapping->i_pages)
+#define flush_dcache_mmap_lock_irqsave(mapping, flags)		\
+		xa_lock_irqsave(&mapping->i_pages, flags)
+#define flush_dcache_mmap_unlock_irqrestore(mapping, flags)	\
+		xa_unlock_irqrestore(&mapping->i_pages, flags)
+
 
 #define flush_icache_page(vma,page)	do { 		\
 	flush_kernel_dcache_page_addr(page_address(page)); \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/checksum.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/checksum.h
@@ -40,7 +40,7 @@
 "	addc		%0, %5, %0\n"
 "	addc		%0, %3, %0\n"
 "1:	ldws,ma		4(%1), %3\n"
-"	addib,<		0, %2, 1b\n"
+"	addib,>		-1, %2, 1b\n"
 "	addc		%0, %3, %0\n"
 "\n"
 "	extru		%0, 31, 16, %4\n"
@@ -126,6 +126,7 @@
 	** Try to keep 4 registers with "live" values ahead of the ALU.
 	*/
 
+"	depdi		0, 31, 32, %0\n"/* clear upper half of incoming checksum */
 "	ldd,ma		8(%1), %4\n"	/* get 1st saddr word */
 "	ldd,ma		8(%2), %5\n"	/* get 1st daddr word */
 "	add		%4, %0, %0\n"
@@ -137,8 +138,8 @@
 "	add,dc		%3, %0, %0\n"  /* fold in proto+len | carry bit */
 "	extrd,u		%0, 31, 32, %4\n"/* copy upper half down */
 "	depdi		0, 31, 32, %0\n"/* clear upper half */
-"	add		%4, %0, %0\n"	/* fold into 32-bits */
-"	addc		0, %0, %0\n"	/* add carry */
+"	add,dc		%4, %0, %0\n"	/* fold into 32-bits, plus carry */
+"	addc		0, %0, %0\n"	/* add final carry */
 
 #else
 
@@ -163,7 +164,8 @@
 "	ldw,ma		4(%2), %7\n"	/* 4th daddr */
 "	addc		%6, %0, %0\n"
 "	addc		%7, %0, %0\n"
-"	addc		%3, %0, %0\n"	/* fold in proto+len, catch carry */
+"	addc		%3, %0, %0\n"	/* fold in proto+len */
+"	addc		0, %0, %0\n"	/* add carry */
 
 #endif
 	: "=r" (sum), "=r" (saddr), "=r" (daddr), "=r" (len),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/fb.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/fb.h
@@ -12,9 +12,13 @@
 	pgprot_val(vma->vm_page_prot) |= _PAGE_NO_CACHE;
 }
 
+#if defined(CONFIG_FB_STI)
+int fb_is_primary_device(struct fb_info *info);
+#else
 static inline int fb_is_primary_device(struct fb_info *info)
 {
 	return 0;
 }
+#endif
 
 #endif /* _ASM_FB_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/futex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/futex.h
@@ -16,7 +16,7 @@
 _futex_spin_lock_irqsave(u32 __user *uaddr, unsigned long int *flags)
 {
 	extern u32 lws_lock_start[];
-	long index = ((long)uaddr & 0x3f8) >> 1;
+	long index = ((long)uaddr & 0x7f8) >> 1;
 	arch_spinlock_t *s = (arch_spinlock_t *)&lws_lock_start[index];
 	local_irq_save(*flags);
 	arch_spin_lock(s);
@@ -26,7 +26,7 @@
 _futex_spin_unlock_irqrestore(u32 __user *uaddr, unsigned long int *flags)
 {
 	extern u32 lws_lock_start[];
-	long index = ((long)uaddr & 0x3f8) >> 1;
+	long index = ((long)uaddr & 0x7f8) >> 1;
 	arch_spinlock_t *s = (arch_spinlock_t *)&lws_lock_start[index];
 	arch_spin_unlock(s);
 	local_irq_restore(*flags);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/hardware.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/hardware.h
@@ -10,12 +10,12 @@
 #define SVERSION_ANY_ID		PA_SVERSION_ANY_ID
 
 struct hp_hardware {
-	unsigned short	hw_type:5;	/* HPHW_xxx */
-	unsigned short	hversion;
-	unsigned long	sversion:28;
-	unsigned short	opt;
-	const char	name[80];	/* The hardware description */
-};
+	unsigned int	hw_type:8;	/* HPHW_xxx */
+	unsigned int	hversion:12;
+	unsigned int	sversion:12;
+	unsigned char	opt;
+	unsigned char	name[59];	/* The hardware description */
+} __packed;
 
 struct parisc_device;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/ldcw.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/ldcw.h
@@ -2,14 +2,28 @@
 #ifndef __PARISC_LDCW_H
 #define __PARISC_LDCW_H
 
-#ifndef CONFIG_PA20
 /* Because kmalloc only guarantees 8-byte alignment for kmalloc'd data,
    and GCC only guarantees 8-byte alignment for stack locals, we can't
    be assured of 16-byte alignment for atomic lock data even if we
    specify "__attribute ((aligned(16)))" in the type declaration.  So,
    we use a struct containing an array of four ints for the atomic lock
    type and dynamically select the 16-byte aligned int from the array
-   for the semaphore.  */
+   for the semaphore. */
+
+/* From: "Jim Hull" <jim.hull of hp.com>
+   I've attached a summary of the change, but basically, for PA 2.0, as
+   long as the ",CO" (coherent operation) completer is implemented, then the
+   16-byte alignment requirement for ldcw and ldcd is relaxed, and instead
+   they only require "natural" alignment (4-byte for ldcw, 8-byte for
+   ldcd).
+
+   Although the cache control hint is accepted by all PA 2.0 processors,
+   it is only implemented on PA8800/PA8900 CPUs. Prior PA8X00 CPUs still
+   require 16-byte alignment. If the address is unaligned, the operation
+   of the instruction is undefined. The ldcw instruction does not generate
+   unaligned data reference traps so misaligned accesses are not detected.
+   This hid the problem for years. So, restore the 16-byte alignment dropped
+   by Kyle McMartin in "Remove __ldcw_align for PA-RISC 2.0 processors". */
 
 #define __PA_LDCW_ALIGNMENT	16
 #define __PA_LDCW_ALIGN_ORDER	4
@@ -19,22 +33,12 @@
 		& ~(__PA_LDCW_ALIGNMENT - 1);			\
 	(volatile unsigned int *) __ret;			\
 })
-#define __LDCW	"ldcw"
 
-#else /*CONFIG_PA20*/
-/* From: "Jim Hull" <jim.hull of hp.com>
-   I've attached a summary of the change, but basically, for PA 2.0, as
-   long as the ",CO" (coherent operation) completer is specified, then the
-   16-byte alignment requirement for ldcw and ldcd is relaxed, and instead
-   they only require "natural" alignment (4-byte for ldcw, 8-byte for
-   ldcd). */
-
-#define __PA_LDCW_ALIGNMENT	4
-#define __PA_LDCW_ALIGN_ORDER	2
-#define __ldcw_align(a) (&(a)->slock)
+#ifdef CONFIG_PA20
 #define __LDCW	"ldcw,co"
-
-#endif /*!CONFIG_PA20*/
+#else
+#define __LDCW	"ldcw"
+#endif
 
 /* LDCW, the only atomic read-write operation PA-RISC has. *sigh*.
    We don't explicitly expose that "*a" may be written as reload
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/led.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/led.h
@@ -11,8 +11,8 @@
 #define	LED1		0x02
 #define	LED0		0x01		/* bottom (or furthest left) LED */
 
-#define	LED_LAN_TX	LED0		/* for LAN transmit activity */
-#define	LED_LAN_RCV	LED1		/* for LAN receive activity */
+#define	LED_LAN_RCV	LED0		/* for LAN receive activity */
+#define	LED_LAN_TX	LED1		/* for LAN transmit activity */
 #define	LED_DISK_IO	LED2		/* for disk activity */
 #define	LED_HEARTBEAT	LED3		/* heartbeat */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/pdc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/pdc.h
@@ -81,6 +81,7 @@
 int pdc_do_reset(void);
 int pdc_soft_power_info(unsigned long *power_reg);
 int pdc_soft_power_button(int sw_control);
+int pdc_soft_power_button_panic(int sw_control);
 void pdc_io_reset(void);
 void pdc_io_reset_devices(void);
 int pdc_iodc_getc(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/pgtable.h
@@ -76,6 +76,8 @@
 	purge_tlb_end(flags);
 }
 
+extern void __update_cache(pte_t pte);
+
 /* Certain architectures need to do special things when PTEs
  * within a page table are directly modified.  Thus, the following
  * hook is made available.
@@ -83,11 +85,14 @@
 #define set_pte(pteptr, pteval)			\
 	do {					\
 		*(pteptr) = (pteval);		\
-		barrier();			\
+		mb();				\
 	} while(0)
 
 #define set_pte_at(mm, addr, pteptr, pteval)	\
 	do {					\
+		if (pte_present(pteval) &&	\
+		    pte_user(pteval))		\
+			__update_cache(pteval);	\
 		*(pteptr) = (pteval);		\
 		purge_tlb_entries(mm, addr);	\
 	} while (0)
@@ -303,6 +308,7 @@
 
 #define pte_none(x)     (pte_val(x) == 0)
 #define pte_present(x)	(pte_val(x) & _PAGE_PRESENT)
+#define pte_user(x)	(pte_val(x) & _PAGE_USER)
 #define pte_clear(mm, addr, xp)  set_pte_at(mm, addr, xp, __pte(0))
 
 #define pmd_flag(x)	(pmd_val(x) & PxD_FLAG_MASK)
@@ -410,7 +416,7 @@
 
 #define PG_dcache_dirty         PG_arch_1
 
-extern void update_mmu_cache(struct vm_area_struct *, unsigned long, pte_t *);
+#define update_mmu_cache(vms,addr,ptep) __update_cache(*ptep)
 
 /* Encode and de-code a swap entry */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/ropes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/ropes.h
@@ -86,6 +86,9 @@
 	struct ioc		ioc[MAX_IOC];
 };
 
+/* list of SBA's in system, see drivers/parisc/sba_iommu.c */
+extern struct sba_device *sba_list;
+
 #define ASTRO_RUNWAY_PORT	0x582
 #define IKE_MERCED_PORT		0x803
 #define REO_MERCED_PORT		0x804
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/rt_sigframe.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/rt_sigframe.h
@@ -2,7 +2,7 @@
 #ifndef _ASM_PARISC_RT_SIGFRAME_H
 #define _ASM_PARISC_RT_SIGFRAME_H
 
-#define SIGRETURN_TRAMP 3
+#define SIGRETURN_TRAMP 4
 #define SIGRESTARTBLOCK_TRAMP 5 
 #define TRAMP_SIZE (SIGRETURN_TRAMP + SIGRESTARTBLOCK_TRAMP)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/special_insns.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/special_insns.h
@@ -2,28 +2,32 @@
 #ifndef __PARISC_SPECIAL_INSNS_H
 #define __PARISC_SPECIAL_INSNS_H
 
-#define lpa(va)	({			\
-	unsigned long pa;		\
-	__asm__ __volatile__(		\
-		"copy %%r0,%0\n\t"	\
-		"lpa %%r0(%1),%0"	\
-		: "=r" (pa)		\
-		: "r" (va)		\
-		: "memory"		\
-	);				\
-	pa;				\
+#define lpa(va)	({					\
+	unsigned long pa;				\
+	__asm__ __volatile__(				\
+		"copy %%r0,%0\n"			\
+		"8:\tlpa %%r0(%1),%0\n"			\
+		"9:\n"					\
+		ASM_EXCEPTIONTABLE_ENTRY(8b, 9b)	\
+		: "=&r" (pa)				\
+		: "r" (va)				\
+		: "memory"				\
+	);						\
+	pa;						\
 })
 
-#define lpa_user(va)	({		\
-	unsigned long pa;		\
-	__asm__ __volatile__(		\
-		"copy %%r0,%0\n\t"	\
-		"lpa %%r0(%%sr3,%1),%0"	\
-		: "=r" (pa)		\
-		: "r" (va)		\
-		: "memory"		\
-	);				\
-	pa;				\
+#define lpa_user(va)	({				\
+	unsigned long pa;				\
+	__asm__ __volatile__(				\
+		"copy %%r0,%0\n"			\
+		"8:\tlpa %%r0(%%sr3,%1),%0\n"		\
+		"9:\n"					\
+		ASM_EXCEPTIONTABLE_ENTRY(8b, 9b)	\
+		: "=&r" (pa)				\
+		: "r" (va)				\
+		: "memory"				\
+	);						\
+	pa;						\
 })
 
 #define mfctl(reg)	({		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/spinlock_types.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/spinlock_types.h
@@ -3,13 +3,8 @@
 #define __ASM_SPINLOCK_TYPES_H
 
 typedef struct {
-#ifdef CONFIG_PA20
-	volatile unsigned int slock;
-# define __ARCH_SPIN_LOCK_UNLOCKED { 1 }
-#else
 	volatile unsigned int lock[4];
 # define __ARCH_SPIN_LOCK_UNLOCKED	{ { 1, 1, 1, 1 } }
-#endif
 } arch_spinlock_t;
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/timex.h
@@ -13,9 +13,10 @@
 
 typedef unsigned long cycles_t;
 
-static inline cycles_t get_cycles (void)
+static inline cycles_t get_cycles(void)
 {
 	return mfctl(16);
 }
+#define get_cycles get_cycles
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/asm/traps.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/asm/traps.h
@@ -17,6 +17,7 @@
 const char *trap_name(unsigned long code);
 void do_page_fault(struct pt_regs *regs, unsigned long code,
 		unsigned long address);
+int handle_nadtlb_fault(struct pt_regs *regs);
 #endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/uapi/asm/errno.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/uapi/asm/errno.h
@@ -75,7 +75,6 @@
 
 /* We now return you to your regularly scheduled HPUX. */
 
-#define ENOSYM		215	/* symbol does not exist in executable */
 #define	ENOTSOCK	216	/* Socket operation on non-socket */
 #define	EDESTADDRREQ	217	/* Destination address required */
 #define	EMSGSIZE	218	/* Message too long */
@@ -101,7 +100,6 @@
 #define	ETIMEDOUT	238	/* Connection timed out */
 #define	ECONNREFUSED	239	/* Connection refused */
 #define	EREFUSED	ECONNREFUSED	/* for HP's NFS apparently */
-#define	EREMOTERELEASE	240	/* Remote peer released connection */
 #define	EHOSTDOWN	241	/* Host is down */
 #define	EHOSTUNREACH	242	/* No route to host */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/uapi/asm/mman.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/uapi/asm/mman.h
@@ -49,31 +49,30 @@
 #define MADV_DONTFORK	10		/* don't inherit across fork */
 #define MADV_DOFORK	11		/* do inherit across fork */
 
-#define MADV_COLD	20		/* deactivate these pages */
-#define MADV_PAGEOUT	21		/* reclaim these pages */
+#define MADV_MERGEABLE   12		/* KSM may merge identical pages */
+#define MADV_UNMERGEABLE 13		/* KSM may not merge identical pages */
 
-#define MADV_POPULATE_READ	22	/* populate (prefault) page tables readable */
-#define MADV_POPULATE_WRITE	23	/* populate (prefault) page tables writable */
+#define MADV_HUGEPAGE	14		/* Worth backing with hugepages */
+#define MADV_NOHUGEPAGE 15		/* Not worth backing with hugepages */
 
-#define MADV_MERGEABLE   65		/* KSM may merge identical pages */
-#define MADV_UNMERGEABLE 66		/* KSM may not merge identical pages */
+#define MADV_DONTDUMP   16		/* Explicity exclude from the core dump,
+					   overrides the coredump filter bits */
+#define MADV_DODUMP	17		/* Clear the MADV_NODUMP flag */
 
-#define MADV_HUGEPAGE	67		/* Worth backing with hugepages */
-#define MADV_NOHUGEPAGE	68		/* Not worth backing with hugepages */
+#define MADV_WIPEONFORK 18		/* Zero memory on fork, child only */
+#define MADV_KEEPONFORK 19		/* Undo MADV_WIPEONFORK */
 
-#define MADV_DONTDUMP   69		/* Explicity exclude from the core dump,
-					   overrides the coredump filter bits */
-#define MADV_DODUMP	70		/* Clear the MADV_NODUMP flag */
+#define MADV_COLD	20		/* deactivate these pages */
+#define MADV_PAGEOUT	21		/* reclaim these pages */
 
-#define MADV_WIPEONFORK 71		/* Zero memory on fork, child only */
-#define MADV_KEEPONFORK 72		/* Undo MADV_WIPEONFORK */
+#define MADV_POPULATE_READ	22	/* populate (prefault) page tables readable */
+#define MADV_POPULATE_WRITE	23	/* populate (prefault) page tables writable */
 
 #define MADV_HWPOISON     100		/* poison a page for testing */
 #define MADV_SOFT_OFFLINE 101		/* soft offline page for testing */
 
 /* compatibility flags */
 #define MAP_FILE	0
-#define MAP_VARIABLE	0
 
 #define PKEY_DISABLE_ACCESS	0x1
 #define PKEY_DISABLE_WRITE	0x2
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/include/uapi/asm/pdc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/include/uapi/asm/pdc.h
@@ -465,6 +465,7 @@
 	unsigned long arch_rev;
 	unsigned long pot_key;
 	unsigned long curr_key;
+	unsigned long width;	/* default of PSW_W bit (1=enabled) */
 };
 
 struct pdc_cache_cf {		/* for PDC_CACHE  (I/D-caches) */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/install.sh
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/install.sh
@@ -39,6 +39,7 @@
 if [ -n "${INSTALLKERNEL}" ]; then
   if [ -x ~/bin/${INSTALLKERNEL} ]; then exec ~/bin/${INSTALLKERNEL} "$@"; fi
   if [ -x /sbin/${INSTALLKERNEL} ]; then exec /sbin/${INSTALLKERNEL} "$@"; fi
+  if [ -x /usr/sbin/${INSTALLKERNEL} ]; then exec /usr/sbin/${INSTALLKERNEL} "$@"; fi
 fi
 
 # Default install
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/cache.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/cache.c
@@ -46,9 +46,6 @@
  */
 DEFINE_SPINLOCK(pa_tlb_flush_lock);
 
-/* Swapper page setup lock. */
-DEFINE_SPINLOCK(pa_swapper_pg_lock);
-
 #if defined(CONFIG_64BIT) && defined(CONFIG_SMP)
 int pa_serialize_tlb_flushes __ro_after_init;
 #endif
@@ -83,9 +80,9 @@
 #define pfn_va(pfn)	__va(PFN_PHYS(pfn))
 
 void
-update_mmu_cache(struct vm_area_struct *vma, unsigned long address, pte_t *ptep)
+__update_cache(pte_t pte)
 {
-	unsigned long pfn = pte_pfn(*ptep);
+	unsigned long pfn = pte_pfn(pte);
 	struct page *page;
 
 	/* We don't have pte special.  As a result, we can be called with
@@ -327,6 +324,7 @@
 	struct vm_area_struct *mpnt;
 	unsigned long offset;
 	unsigned long addr, old_addr = 0;
+	unsigned long flags;
 	pgoff_t pgoff;
 
 	if (mapping && !mapping_mapped(mapping)) {
@@ -346,7 +344,7 @@
 	 * declared as MAP_PRIVATE or MAP_SHARED), so we only need
 	 * to flush one address here for them all to become coherent */
 
-	flush_dcache_mmap_lock(mapping);
+	flush_dcache_mmap_lock_irqsave(mapping, flags);
 	vma_interval_tree_foreach(mpnt, &mapping->i_mmap, pgoff, pgoff) {
 		offset = (pgoff - mpnt->vm_pgoff) << PAGE_SHIFT;
 		addr = mpnt->vm_start + offset;
@@ -369,7 +367,7 @@
 			old_addr = addr;
 		}
 	}
-	flush_dcache_mmap_unlock(mapping);
+	flush_dcache_mmap_unlock_irqrestore(mapping, flags);
 }
 EXPORT_SYMBOL(flush_dcache_page);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/drivers.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/drivers.c
@@ -520,7 +520,6 @@
 	dev->id.hversion_rev = iodc_data[1] & 0x0f;
 	dev->id.sversion = ((iodc_data[4] & 0x0f) << 16) |
 			(iodc_data[5] << 8) | iodc_data[6];
-	dev->hpa.name = parisc_pathname(dev);
 	dev->hpa.start = hpa;
 	/* This is awkward.  The STI spec says that gfx devices may occupy
 	 * 32MB or 64MB.  Unfortunately, we don't know how to tell whether
@@ -534,10 +533,10 @@
 		dev->hpa.end = hpa + 0xfff;
 	}
 	dev->hpa.flags = IORESOURCE_MEM;
-	name = parisc_hardware_description(&dev->id);
-	if (name) {
-		strlcpy(dev->name, name, sizeof(dev->name));
-	}
+	dev->hpa.name = dev->name;
+	name = parisc_hardware_description(&dev->id) ? : "unknown";
+	snprintf(dev->name, sizeof(dev->name), "%s [%s]",
+		name, parisc_pathname(dev));
 
 	/* Silently fail things like mouse ports which are subsumed within
 	 * the keyboard controller
@@ -883,15 +882,13 @@
 			&root);
 }
 
-static void print_parisc_device(struct parisc_device *dev)
+static __init void print_parisc_device(struct parisc_device *dev)
 {
-	char hw_path[64];
-	static int count;
+	static int count __initdata;
 
-	print_pa_hwpath(dev, hw_path);
-	pr_info("%d. %s at %pap [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
-		++count, dev->name, &(dev->hpa.start), hw_path, dev->id.hw_type,
-		dev->id.hversion_rev, dev->id.hversion, dev->id.sversion);
+	pr_info("%d. %s at %pap { type:%d, hv:%#x, sv:%#x, rev:%#x }",
+		++count, dev->name, &(dev->hpa.start), dev->id.hw_type,
+		dev->id.hversion, dev->id.sversion, dev->id.hversion_rev);
 
 	if (dev->num_addrs) {
 		int k;
@@ -927,9 +924,9 @@
 	pr_info("#define PARISC_MODEL \"%s\"\n\n",
 			boot_cpu_data.pdc.sys_model_name);
 
+	#define p ((unsigned long *)&boot_cpu_data.pdc.model)
 	pr_info("#define PARISC_PDC_MODEL 0x%lx, 0x%lx, 0x%lx, "
 		"0x%lx, 0x%lx, 0x%lx, 0x%lx, 0x%lx, 0x%lx\n\n",
-	#define p ((unsigned long *)&boot_cpu_data.pdc.model)
 		p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], p[8]);
 	#undef p
 
@@ -1080,7 +1077,7 @@
 
 
 
-static int print_one_device(struct device * dev, void * data)
+static __init int print_one_device(struct device * dev, void * data)
 {
 	struct parisc_device * pdev = to_parisc_device(dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/entry.S
@@ -497,13 +497,13 @@
 	 * to a CPU TLB 4k PFN (4k => 12 bits to shift) */
 	#define PAGE_ADD_SHIFT		(PAGE_SHIFT-12)
 	#define PAGE_ADD_HUGE_SHIFT	(REAL_HPAGE_SHIFT-12)
+	#define PFN_START_BIT	(63-ASM_PFN_PTE_SHIFT+(63-58)-PAGE_ADD_SHIFT)
 
 	/* Drop prot bits and convert to page addr for iitlbt and idtlbt */
 	.macro		convert_for_tlb_insert20 pte,tmp
 #ifdef CONFIG_HUGETLB_PAGE
 	copy		\pte,\tmp
-	extrd,u		\tmp,(63-ASM_PFN_PTE_SHIFT)+(63-58)+PAGE_ADD_SHIFT,\
-				64-PAGE_SHIFT-PAGE_ADD_SHIFT,\pte
+	extrd,u		\tmp,PFN_START_BIT,PFN_START_BIT+1,\pte
 
 	depdi		_PAGE_SIZE_ENCODING_DEFAULT,63,\
 				(63-58)+PAGE_ADD_SHIFT,\pte
@@ -511,8 +511,7 @@
 	depdi		_HUGE_PAGE_SIZE_ENCODING_DEFAULT,63,\
 				(63-58)+PAGE_ADD_HUGE_SHIFT,\pte
 #else /* Huge pages disabled */
-	extrd,u		\pte,(63-ASM_PFN_PTE_SHIFT)+(63-58)+PAGE_ADD_SHIFT,\
-				64-PAGE_SHIFT-PAGE_ADD_SHIFT,\pte
+	extrd,u		\pte,PFN_START_BIT,PFN_START_BIT+1,\pte
 	depdi		_PAGE_SIZE_ENCODING_DEFAULT,63,\
 				(63-58)+PAGE_ADD_SHIFT,\pte
 #endif
@@ -1072,8 +1071,7 @@
 	STREG           %r16, PT_ISR(%r29)
 	STREG           %r17, PT_IOR(%r29)
 
-#if 0 && defined(CONFIG_64BIT)
-	/* Revisit when we have 64-bit code above 4Gb */
+#if defined(CONFIG_64BIT)
 	b,n		intr_save2
 
 skip_save_ior:
@@ -1081,8 +1079,7 @@
 	 * need to adjust iasq/iaoq here in the same way we adjusted isr/ior
 	 * above.
 	 */
-	extrd,u,*	%r8,PSW_W_BIT,1,%r1
-	cmpib,COND(=),n	1,%r1,intr_save2
+	bb,COND(>=),n	%r8,PSW_W_BIT,intr_save2
 	LDREG		PT_IASQ0(%r29), %r16
 	LDREG		PT_IAOQ0(%r29), %r17
 	/* adjust iasq/iaoq */
@@ -1834,8 +1831,8 @@
 	LDREG	TI_TASK-THREAD_SZ_ALGN-FRAME_SIZE(%r30),%r1
 
 	/* Are we being ptraced? */
-	ldw	TASK_FLAGS(%r1),%r19
-	ldi	_TIF_SYSCALL_TRACE_MASK,%r2
+	LDREG	TI_FLAGS-THREAD_SZ_ALGN-FRAME_SIZE(%r30),%r19
+	ldi	_TIF_SINGLESTEP|_TIF_BLOCKSTEP,%r2
 	and,COND(=)	%r19,%r2,%r0
 	b,n	syscall_restore_rfi
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/firmware.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/firmware.c
@@ -123,10 +123,10 @@
 #ifdef CONFIG_64BIT
 	if(unlikely(parisc_narrow_firmware)) {
 		if((address & 0xff000000) == 0xf0000000)
-			return 0xf0f0f0f000000000UL | (u32)address;
+			return (0xfffffff0UL << 32) | (u32)address;
 
 		if((address & 0xf0000000) == 0xf0000000)
-			return 0xffffffff00000000UL | (u32)address;
+			return (0xffffffffUL << 32) | (u32)address;
 	}
 #endif
 	return address;
@@ -1158,15 +1158,18 @@
 }
 
 /*
- * pdc_soft_power_button - Control the soft power button behaviour
- * @sw_control: 0 for hardware control, 1 for software control 
+ * pdc_soft_power_button{_panic} - Control the soft power button behaviour
+ * @sw_control: 0 for hardware control, 1 for software control
  *
  *
  * This PDC function places the soft power button under software or
  * hardware control.
- * Under software control the OS may control to when to allow to shut 
- * down the system. Under hardware control pressing the power button 
+ * Under software control the OS may control to when to allow to shut
+ * down the system. Under hardware control pressing the power button
  * powers off the system immediately.
+ *
+ * The _panic version relies on spin_trylock to prevent deadlock
+ * on panic path.
  */
 int pdc_soft_power_button(int sw_control)
 {
@@ -1180,6 +1183,22 @@
 	return retval;
 }
 
+int pdc_soft_power_button_panic(int sw_control)
+{
+	int retval;
+	unsigned long flags;
+
+	if (!spin_trylock_irqsave(&pdc_lock, flags)) {
+		pr_emerg("Couldn't enable soft power button\n");
+		return -EBUSY; /* ignored by the panic notifier */
+	}
+
+	retval = mem_pdc_call(PDC_SOFT_POWER, PDC_SOFT_POWER_ENABLE, __pa(pdc_result), sw_control);
+	spin_unlock_irqrestore(&pdc_lock, flags);
+
+	return retval;
+}
+
 /*
  * pdc_io_reset - Hack to avoid overlapping range registers of Bridges devices.
  * Primarily a problem on T600 (which parisc-linux doesn't support) but
@@ -1230,7 +1249,7 @@
  */
 int pdc_iodc_print(const unsigned char *str, unsigned count)
 {
-	unsigned int i;
+	unsigned int i, found = 0;
 	unsigned long flags;
 
 	for (i = 0; i < count;) {
@@ -1239,6 +1258,7 @@
 			iodc_dbuf[i+0] = '\r';
 			iodc_dbuf[i+1] = '\n';
 			i += 2;
+			found = 1;
 			goto print;
 		default:
 			iodc_dbuf[i] = str[i];
@@ -1255,7 +1275,7 @@
                     __pa(iodc_retbuf), 0, __pa(iodc_dbuf), i, 0);
         spin_unlock_irqrestore(&pdc_lock, flags);
 
-	return i;
+	return i - found;
 }
 
 #if !defined(BOOTLOADER)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/ftrace.c
@@ -81,7 +81,7 @@
 #endif
 }
 
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+#if defined(CONFIG_DYNAMIC_FTRACE) && defined(CONFIG_FUNCTION_GRAPH_TRACER)
 int ftrace_enable_ftrace_graph_caller(void)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/head.S
@@ -22,7 +22,7 @@
 #include <linux/init.h>
 #include <linux/pgtable.h>
 
-	.level	PA_ASM_LEVEL
+	.level	1.1
 
 	__INITDATA
 ENTRY(boot_args)
@@ -69,6 +69,46 @@
 	stw,ma          %arg2,4(%r1)
 	stw,ma          %arg3,4(%r1)
 
+#if defined(CONFIG_PA20)
+	/* check for 64-bit capable CPU as required by current kernel */
+	ldi		32,%r10
+	mtctl		%r10,%cr11
+	.level 2.0
+	mfctl,w		%cr11,%r10
+	.level 1.1
+	comib,<>,n	0,%r10,$cpu_ok
+
+	load32		PA(msg1),%arg0
+	ldi		msg1_end-msg1,%arg1
+$iodc_panic:
+	copy		%arg0, %r10
+	copy		%arg1, %r11
+	load32		PA(init_stack),%sp
+#define MEM_CONS 0x3A0
+	ldw		MEM_CONS+32(%r0),%arg0	// HPA
+	ldi		ENTRY_IO_COUT,%arg1
+	ldw		MEM_CONS+36(%r0),%arg2	// SPA
+	ldw		MEM_CONS+8(%r0),%arg3	// layers
+	load32		PA(__bss_start),%r1
+	stw		%r1,-52(%sp)		// arg4
+	stw		%r0,-56(%sp)		// arg5
+	stw		%r10,-60(%sp)		// arg6 = ptr to text
+	stw		%r11,-64(%sp)		// arg7 = len
+	stw		%r0,-68(%sp)		// arg8
+	load32		PA(.iodc_panic_ret), %rp
+	ldw		MEM_CONS+40(%r0),%r1	// ENTRY_IODC
+	bv,n		(%r1)
+.iodc_panic_ret:
+	b .				/* wait endless with ... */
+	or		%r10,%r10,%r10	/* qemu idle sleep */
+msg1:	.ascii "Can't boot kernel which was built for PA8x00 CPUs on this machine.\r\n"
+msg1_end:
+
+$cpu_ok:
+#endif
+
+	.level	PA_ASM_LEVEL
+
 	/* Initialize startup VM. Just map first 16/32 MB of memory */
 	load32		PA(swapper_pg_dir),%r4
 	mtctl		%r4,%cr24	/* Initialize kernel root pointer */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/irq.c
@@ -333,7 +333,7 @@
 {
 #ifdef CONFIG_SMP
 	struct irq_data *d = irq_get_irq_data(irq);
-	cpumask_copy(irq_data_get_affinity_mask(d), cpumask_of(cpu));
+	irq_data_update_affinity(d, cpumask_of(cpu));
 #endif
 
 	return per_cpu(cpu_data, cpu).txn_addr;
@@ -386,7 +386,7 @@
 	volatile unsigned int lock[1];
 };
 
-DEFINE_PER_CPU(union irq_stack_union, irq_stack_union) = {
+static DEFINE_PER_CPU(union irq_stack_union, irq_stack_union) = {
 		.slock = { 1,1,1,1 },
 	};
 #endif
@@ -518,7 +518,7 @@
 
 	old_regs = set_irq_regs(regs);
 	local_irq_disable();
-	irq_enter();
+	irq_enter_rcu();
 
 	eirr_val = mfctl(23) & cpu_eiem & per_cpu(local_ack_eiem, cpu);
 	if (!eirr_val)
@@ -553,7 +553,7 @@
 #endif /* CONFIG_IRQSTACKS */
 
  out:
-	irq_exit();
+	irq_exit_rcu();
 	set_irq_regs(old_regs);
 	return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/kprobes.c
@@ -175,7 +175,7 @@
 	return 1;
 }
 
-static inline void kretprobe_trampoline(void)
+void __kretprobe_trampoline(void)
 {
 	asm volatile("nop");
 	asm volatile("nop");
@@ -193,7 +193,7 @@
 {
 	unsigned long orig_ret_address;
 
-	orig_ret_address = __kretprobe_trampoline_handler(regs, trampoline_p.addr, NULL);
+	orig_ret_address = __kretprobe_trampoline_handler(regs, NULL);
 	instruction_pointer_set(regs, orig_ret_address);
 
 	return 1;
@@ -217,6 +217,6 @@
 int __init arch_init_kprobes(void)
 {
 	trampoline_p.addr = (kprobe_opcode_t *)
-		dereference_function_descriptor(kretprobe_trampoline);
+		dereference_function_descriptor(__kretprobe_trampoline);
 	return register_kprobe(&trampoline_p);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/parisc_ksyms.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/parisc_ksyms.c
@@ -21,6 +21,7 @@
 #include <linux/atomic.h>
 EXPORT_SYMBOL(__xchg8);
 EXPORT_SYMBOL(__xchg32);
+EXPORT_SYMBOL(__cmpxchg_u8);
 EXPORT_SYMBOL(__cmpxchg_u32);
 EXPORT_SYMBOL(__cmpxchg_u64);
 #ifdef CONFIG_SMP
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/patch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/patch.c
@@ -40,10 +40,7 @@
 
 	*need_unmap = 1;
 	set_fixmap(fixmap, page_to_phys(page));
-	if (flags)
-		raw_spin_lock_irqsave(&patch_lock, *flags);
-	else
-		__acquire(&patch_lock);
+	raw_spin_lock_irqsave(&patch_lock, *flags);
 
 	return (void *) (__fix_to_virt(fixmap) + (uintaddr & ~PAGE_MASK));
 }
@@ -52,10 +49,7 @@
 {
 	clear_fixmap(fixmap);
 
-	if (flags)
-		raw_spin_unlock_irqrestore(&patch_lock, *flags);
-	else
-		__release(&patch_lock);
+	raw_spin_unlock_irqrestore(&patch_lock, *flags);
 }
 
 void __kprobes __patch_text_multiple(void *addr, u32 *insn, unsigned int len)
@@ -67,8 +61,9 @@
 	int mapped;
 
 	/* Make sure we don't have any aliases in cache */
-	flush_kernel_vmap_range(addr, len);
-	flush_icache_range(start, end);
+	flush_kernel_dcache_range_asm(start, end);
+	flush_kernel_icache_range_asm(start, end);
+	flush_tlb_kernel_range(start, end);
 
 	p = fixmap = patch_map(addr, FIX_TEXT_POKE0, &flags, &mapped);
 
@@ -81,8 +76,10 @@
 			 * We're crossing a page boundary, so
 			 * need to remap
 			 */
-			flush_kernel_vmap_range((void *)fixmap,
-						(p-fixmap) * sizeof(*p));
+			flush_kernel_dcache_range_asm((unsigned long)fixmap,
+						      (unsigned long)p);
+			flush_tlb_kernel_range((unsigned long)fixmap,
+					       (unsigned long)p);
 			if (mapped)
 				patch_unmap(FIX_TEXT_POKE0, &flags);
 			p = fixmap = patch_map(addr, FIX_TEXT_POKE0, &flags,
@@ -90,10 +87,10 @@
 		}
 	}
 
-	flush_kernel_vmap_range((void *)fixmap, (p-fixmap) * sizeof(*p));
+	flush_kernel_dcache_range_asm((unsigned long)fixmap, (unsigned long)p);
+	flush_tlb_kernel_range((unsigned long)fixmap, (unsigned long)p);
 	if (mapped)
 		patch_unmap(FIX_TEXT_POKE0, &flags);
-	flush_icache_range(start, end);
 }
 
 void __kprobes __patch_text(void *addr, u32 insn)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/pci-dma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/pci-dma.c
@@ -446,11 +446,27 @@
 void arch_sync_dma_for_device(phys_addr_t paddr, size_t size,
 		enum dma_data_direction dir)
 {
+	/*
+	 * fdc: The data cache line is written back to memory, if and only if
+	 * it is dirty, and then invalidated from the data cache.
+	 */
 	flush_kernel_dcache_range((unsigned long)phys_to_virt(paddr), size);
 }
 
 void arch_sync_dma_for_cpu(phys_addr_t paddr, size_t size,
 		enum dma_data_direction dir)
 {
-	flush_kernel_dcache_range((unsigned long)phys_to_virt(paddr), size);
+	unsigned long addr = (unsigned long) phys_to_virt(paddr);
+
+	switch (dir) {
+	case DMA_TO_DEVICE:
+	case DMA_BIDIRECTIONAL:
+		flush_kernel_dcache_range(addr, size);
+		return;
+	case DMA_FROM_DEVICE:
+		purge_kernel_dcache_range_asm(addr, addr + size);
+		return;
+	default:
+		BUG();
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/process.c
@@ -120,13 +120,18 @@
 	/* It seems we have no way to power the system off via
 	 * software. The user has to press the button himself. */
 
-	printk(KERN_EMERG "System shut down completed.\n"
-	       "Please power this system off now.");
+	printk("Power off or press RETURN to reboot.\n");
 
 	/* prevent soft lockup/stalled CPU messages for endless loop. */
 	rcu_sysrq_start();
 	lockup_detector_soft_poweroff();
-	for (;;);
+	while (1) {
+		/* reboot if user presses RETURN key */
+		if (pdc_iodc_getc() == 13) {
+			printk("Rebooting...\n");
+			machine_restart(NULL);
+		}
+	}
 }
 
 void (*pm_power_off)(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/processor.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/processor.c
@@ -372,10 +372,18 @@
 show_cpuinfo (struct seq_file *m, void *v)
 {
 	unsigned long cpu;
+	char cpu_name[60], *p;
+
+	/* strip PA path from CPU name to not confuse lscpu */
+	strlcpy(cpu_name, per_cpu(cpu_data, 0).dev->name, sizeof(cpu_name));
+	p = strrchr(cpu_name, '[');
+	if (p)
+		*(--p) = 0;
 
 	for_each_online_cpu(cpu) {
-		const struct cpuinfo_parisc *cpuinfo = &per_cpu(cpu_data, cpu);
 #ifdef CONFIG_SMP
+		const struct cpuinfo_parisc *cpuinfo = &per_cpu(cpu_data, cpu);
+
 		if (0 == cpuinfo->hpa)
 			continue;
 #endif
@@ -418,11 +426,9 @@
 		}
 		seq_printf(m, " (0x%02lx)\n", boot_cpu_data.pdc.capabilities);
 
-		seq_printf(m, "model\t\t: %s\n"
-				"model name\t: %s\n",
+		seq_printf(m, "model\t\t: %s - %s\n",
 				 boot_cpu_data.pdc.sys_model_name,
-				 cpuinfo->dev ?
-				 cpuinfo->dev->name : "Unknown");
+				 cpu_name);
 
 		seq_printf(m, "hversion\t: 0x%08x\n"
 			        "sversion\t: 0x%08x\n",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/ptrace.c
@@ -127,6 +127,12 @@
 	unsigned long tmp;
 	long ret = -EIO;
 
+	unsigned long user_regs_struct_size = sizeof(struct user_regs_struct);
+#ifdef CONFIG_64BIT
+	if (is_compat_task())
+		user_regs_struct_size /= 2;
+#endif
+
 	switch (request) {
 
 	/* Read the word at location addr in the USER area.  For ptraced
@@ -182,14 +188,14 @@
 		return copy_regset_to_user(child,
 					   task_user_regset_view(current),
 					   REGSET_GENERAL,
-					   0, sizeof(struct user_regs_struct),
+					   0, user_regs_struct_size,
 					   datap);
 
 	case PTRACE_SETREGS:	/* Set all gp regs in the child. */
 		return copy_regset_from_user(child,
 					     task_user_regset_view(current),
 					     REGSET_GENERAL,
-					     0, sizeof(struct user_regs_struct),
+					     0, user_regs_struct_size,
 					     datap);
 
 	case PTRACE_GETFPREGS:	/* Get the child FPU state. */
@@ -303,6 +309,11 @@
 			}
 		}
 		break;
+	case PTRACE_GETREGS:
+	case PTRACE_SETREGS:
+	case PTRACE_GETFPREGS:
+	case PTRACE_SETFPREGS:
+		return arch_ptrace(child, request, addr, data);
 
 	default:
 		ret = compat_ptrace_request(child, request, addr, data);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/real2.S
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/real2.S
@@ -248,9 +248,6 @@
 	/* save fn */
 	copy	%arg2, %r31
 
-	/* set up the new ap */
-	ldo	64(%arg1), %r29
-
 	/* load up the arg registers from the saved arg area */
 	/* 32-bit calling convention passes first 4 args in registers */
 	ldd	0*REG_SZ(%arg1), %arg0		/* note overwriting arg0 */
@@ -262,7 +259,9 @@
 	ldd	7*REG_SZ(%arg1), %r19
 	ldd	1*REG_SZ(%arg1), %arg1		/* do this one last! */
 
+	/* set up real-mode stack and real-mode ap */
 	tophys_r1 %sp
+	ldo	-16(%sp), %r29			/* Reference param save area */
 
 	b,l	rfi_virt2real,%r2
 	nop
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/setup.c
@@ -150,6 +150,8 @@
 #ifdef CONFIG_PA11
 	dma_ops_init();
 #endif
+
+	clear_sched_clock_stable();
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/signal.c
@@ -288,21 +288,22 @@
 	   already in userspace. The first words of tramp are used to
 	   save the previous sigrestartblock trampoline that might be
 	   on the stack. We start the sigreturn trampoline at 
-	   SIGRESTARTBLOCK_TRAMP. */
+	   SIGRESTARTBLOCK_TRAMP+X. */
 	err |= __put_user(in_syscall ? INSN_LDI_R25_1 : INSN_LDI_R25_0,
 			&frame->tramp[SIGRESTARTBLOCK_TRAMP+0]);
-	err |= __put_user(INSN_BLE_SR2_R0, 
-			&frame->tramp[SIGRESTARTBLOCK_TRAMP+1]);
 	err |= __put_user(INSN_LDI_R20,
+			&frame->tramp[SIGRESTARTBLOCK_TRAMP+1]);
+	err |= __put_user(INSN_BLE_SR2_R0,
 			&frame->tramp[SIGRESTARTBLOCK_TRAMP+2]);
+	err |= __put_user(INSN_NOP, &frame->tramp[SIGRESTARTBLOCK_TRAMP+3]);
 
-	start = (unsigned long) &frame->tramp[SIGRESTARTBLOCK_TRAMP+0];
-	end = (unsigned long) &frame->tramp[SIGRESTARTBLOCK_TRAMP+3];
+	start = (unsigned long) &frame->tramp[0];
+	end = (unsigned long) &frame->tramp[TRAMP_SIZE];
 	flush_user_dcache_range_asm(start, end);
 	flush_user_icache_range_asm(start, end);
 
 	/* TRAMP Words 0-4, Length 5 = SIGRESTARTBLOCK_TRAMP
-	 * TRAMP Words 5-7, Length 3 = SIGRETURN_TRAMP
+	 * TRAMP Words 5-9, Length 4 = SIGRETURN_TRAMP
 	 * So the SIGRETURN_TRAMP is at the end of SIGRESTARTBLOCK_TRAMP
 	 */
 	rp = (unsigned long) &frame->tramp[SIGRESTARTBLOCK_TRAMP];
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/signal32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/signal32.h
@@ -36,7 +36,7 @@
         compat_int_t rf_sar;
 };
 
-#define COMPAT_SIGRETURN_TRAMP 3
+#define COMPAT_SIGRETURN_TRAMP 4
 #define COMPAT_SIGRESTARTBLOCK_TRAMP 5
 #define COMPAT_TRAMP_SIZE (COMPAT_SIGRETURN_TRAMP + \
 				COMPAT_SIGRESTARTBLOCK_TRAMP)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/smp.c
@@ -29,6 +29,7 @@
 #include <linux/bitops.h>
 #include <linux/ftrace.h>
 #include <linux/cpu.h>
+#include <linux/kgdb.h>
 
 #include <linux/atomic.h>
 #include <asm/current.h>
@@ -69,7 +70,10 @@
 	IPI_CALL_FUNC,
 	IPI_CPU_START,
 	IPI_CPU_STOP,
-	IPI_CPU_TEST
+	IPI_CPU_TEST,
+#ifdef CONFIG_KGDB
+	IPI_ENTER_KGDB,
+#endif
 };
 
 
@@ -167,7 +171,12 @@
 			case IPI_CPU_TEST:
 				smp_debug(100, KERN_DEBUG "CPU%d is alive!\n", this_cpu);
 				break;
-
+#ifdef CONFIG_KGDB
+			case IPI_ENTER_KGDB:
+				smp_debug(100, KERN_DEBUG "CPU%d ENTER_KGDB\n", this_cpu);
+				kgdb_nmicallback(raw_smp_processor_id(), get_irq_regs());
+				break;
+#endif
 			default:
 				printk(KERN_CRIT "Unknown IPI num on CPU%d: %lu\n",
 					this_cpu, which);
@@ -226,6 +235,12 @@
 	}
 }
 
+#ifdef CONFIG_KGDB
+void kgdb_roundup_cpus(void)
+{
+	send_IPI_allbutself(IPI_ENTER_KGDB);
+}
+#endif
 
 inline void 
 smp_send_stop(void)	{ send_IPI_allbutself(IPI_CPU_STOP); }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/sys_parisc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/sys_parisc.c
@@ -463,3 +463,30 @@
 	flags = FIX_O_NONBLOCK(flags);
 	return sys_inotify_init1(flags);
 }
+
+/*
+ * madvise() wrapper
+ *
+ * Up to kernel v6.1 parisc has different values than all other
+ * platforms for the MADV_xxx flags listed below.
+ * To keep binary compatibility with existing userspace programs
+ * translate the former values to the new values.
+ *
+ * XXX: Remove this wrapper in year 2025 (or later)
+ */
+
+asmlinkage notrace long parisc_madvise(unsigned long start, size_t len_in, int behavior)
+{
+	switch (behavior) {
+	case 65: behavior = MADV_MERGEABLE;	break;
+	case 66: behavior = MADV_UNMERGEABLE;	break;
+	case 67: behavior = MADV_HUGEPAGE;	break;
+	case 68: behavior = MADV_NOHUGEPAGE;	break;
+	case 69: behavior = MADV_DONTDUMP;	break;
+	case 70: behavior = MADV_DODUMP;	break;
+	case 71: behavior = MADV_WIPEONFORK;	break;
+	case 72: behavior = MADV_KEEPONFORK;	break;
+	}
+
+	return sys_madvise(start, len_in, behavior);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/sys_parisc32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/sys_parisc32.c
@@ -23,12 +23,3 @@
     	current->comm, current->pid, r20);
     return -ENOSYS;
 }
-
-asmlinkage long sys32_fanotify_mark(compat_int_t fanotify_fd, compat_uint_t flags,
-	compat_uint_t mask0, compat_uint_t mask1, compat_int_t dfd,
-	const char  __user * pathname)
-{
-	return sys_fanotify_mark(fanotify_fd, flags,
-			((__u64)mask1 << 32) | mask0,
-			 dfd, pathname);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/syscall.S
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/syscall.S
@@ -217,10 +217,10 @@
 
 #ifdef CONFIG_64BIT
 	ldil	L%sys_call_table, %r1
-	or,=	%r2,%r2,%r2
-	addil	L%(sys_call_table64-sys_call_table), %r1
+	or,ev	%r2,%r2,%r2
+	ldil	L%sys_call_table64, %r1
 	ldo	R%sys_call_table(%r1), %r19
-	or,=	%r2,%r2,%r2
+	or,ev	%r2,%r2,%r2
 	ldo	R%sys_call_table64(%r1), %r19
 #else
 	load32	sys_call_table, %r19
@@ -355,10 +355,10 @@
 	extrd,u	%r19,63,1,%r2			/* W hidden in bottom bit */
 
 	ldil	L%sys_call_table, %r1
-	or,=	%r2,%r2,%r2
-	addil	L%(sys_call_table64-sys_call_table), %r1
+	or,ev	%r2,%r2,%r2
+	ldil	L%sys_call_table64, %r1
 	ldo	R%sys_call_table(%r1), %r19
-	or,=	%r2,%r2,%r2
+	or,ev	%r2,%r2,%r2
 	ldo	R%sys_call_table64(%r1), %r19
 #else
 	load32	sys_call_table, %r19
@@ -478,7 +478,7 @@
 	extrd,u	%r1,PSW_W_BIT,1,%r1
 	/* sp must be aligned on 4, so deposit the W bit setting into
 	 * the bottom of sp temporarily */
-	or,ev	%r1,%r30,%r30
+	or,od	%r1,%r30,%r30
 
 	/* Clip LWS number to a 32-bit value for 32-bit processes */
 	depdi	0, 31, 32, %r20
@@ -932,6 +932,8 @@
 END(sys_call_table)
 
 #ifdef CONFIG_64BIT
+#undef __SYSCALL_WITH_COMPAT
+#define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, native)
 	.align 8
 ENTRY(sys_call_table64)
 #include <asm/syscall_table_64.h>    /* 64-bit syscalls */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/syscalls/syscall.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/syscalls/syscall.tbl
@@ -108,7 +108,7 @@
 95	common	fchown			sys_fchown
 96	common	getpriority		sys_getpriority
 97	common	setpriority		sys_setpriority
-98	common	recv			sys_recv
+98	common	recv			sys_recv			compat_sys_recv
 99	common	statfs			sys_statfs			compat_sys_statfs
 100	common	fstatfs			sys_fstatfs			compat_sys_fstatfs
 101	common	stat64			sys_stat64
@@ -131,11 +131,11 @@
 116	common	sysinfo			sys_sysinfo			compat_sys_sysinfo
 117	common	shutdown		sys_shutdown
 118	common	fsync			sys_fsync
-119	common	madvise			sys_madvise
+119	common	madvise			parisc_madvise
 120	common	clone			sys_clone_wrapper
 121	common	setdomainname		sys_setdomainname
 122	common	sendfile		sys_sendfile			compat_sys_sendfile
-123	common	recvfrom		sys_recvfrom
+123	common	recvfrom		sys_recvfrom			compat_sys_recvfrom
 124	32	adjtimex		sys_adjtimex_time32
 124	64	adjtimex		sys_adjtimex
 125	common	mprotect		sys_mprotect
@@ -364,7 +364,7 @@
 320	common	accept4			sys_accept4
 321	common	prlimit64		sys_prlimit64
 322	common	fanotify_init		sys_fanotify_init
-323	common	fanotify_mark		sys_fanotify_mark		sys32_fanotify_mark
+323	common	fanotify_mark		sys_fanotify_mark		compat_sys_fanotify_mark
 324	32	clock_adjtime		sys_clock_adjtime32
 324	64	clock_adjtime		sys_clock_adjtime
 325	common	name_to_handle_at	sys_name_to_handle_at
@@ -413,7 +413,7 @@
 412	32	utimensat_time64		sys_utimensat			sys_utimensat
 413	32	pselect6_time64			sys_pselect6			compat_sys_pselect6_time64
 414	32	ppoll_time64			sys_ppoll			compat_sys_ppoll_time64
-416	32	io_pgetevents_time64		sys_io_pgetevents		sys_io_pgetevents
+416	32	io_pgetevents_time64		sys_io_pgetevents		compat_sys_io_pgetevents_time64
 417	32	recvmmsg_time64			sys_recvmmsg			compat_sys_recvmmsg_time64
 418	32	mq_timedsend_time64		sys_mq_timedsend		sys_mq_timedsend
 419	32	mq_timedreceive_time64		sys_mq_timedreceive		sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/time.c
@@ -249,30 +249,12 @@
 static int __init init_cr16_clocksource(void)
 {
 	/*
-	 * The cr16 interval timers are not syncronized across CPUs on
-	 * different sockets, so mark them unstable and lower rating on
-	 * multi-socket SMP systems.
+	 * The cr16 interval timers are not synchronized across CPUs.
 	 */
 	if (num_online_cpus() > 1 && !running_on_qemu) {
-		int cpu;
-		unsigned long cpu0_loc;
-		cpu0_loc = per_cpu(cpu_data, 0).cpu_loc;
-
-		for_each_online_cpu(cpu) {
-			if (cpu == 0)
-				continue;
-			if ((cpu0_loc != 0) &&
-			    (cpu0_loc == per_cpu(cpu_data, cpu).cpu_loc))
-				continue;
-
-			/* mark sched_clock unstable */
-			clear_sched_clock_stable();
-
-			clocksource_cr16.name = "cr16_unstable";
-			clocksource_cr16.flags = CLOCK_SOURCE_UNSTABLE;
-			clocksource_cr16.rating = 0;
-			break;
-		}
+		clocksource_cr16.name = "cr16_unstable";
+		clocksource_cr16.flags = CLOCK_SOURCE_UNSTABLE;
+		clocksource_cr16.rating = 0;
 	}
 
 	/* register at clocksource framework */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/traps.c
@@ -268,7 +268,7 @@
 		panic("Fatal exception");
 
 	oops_exit();
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 /* gdb uses break 4,8 */
@@ -305,8 +305,8 @@
 #endif
 
 #ifdef CONFIG_KGDB
-	if (unlikely(iir == PARISC_KGDB_COMPILED_BREAK_INSN ||
-		iir == PARISC_KGDB_BREAK_INSN)) {
+	if (unlikely((iir == PARISC_KGDB_COMPILED_BREAK_INSN ||
+		iir == PARISC_KGDB_BREAK_INSN)) && !user_mode(regs)) {
 		kgdb_handle_exception(9, SIGTRAP, 0, regs);
 		return;
 	}
@@ -661,6 +661,8 @@
 			 by hand. Technically we need to emulate:
 			 fdc,fdce,pdc,"fic,4f",prober,probeir,probew, probeiw
 		*/
+		if (code == 17 && handle_nadtlb_fault(regs))
+			return;
 		fault_address = regs->ior;
 		fault_space = regs->isr;
 		break;
@@ -729,6 +731,8 @@
 			}
 			mmap_read_unlock(current->mm);
 		}
+		/* CPU could not fetch instruction, so clear stale IIR value. */
+		regs->iir = 0xbaadf00d;
 		fallthrough;
 	case 27: 
 		/* Data memory protection ID trap */
@@ -782,7 +786,7 @@
 	     * unless pagefault_disable() was called before.
 	     */
 
-	    if (fault_space == 0 && !faulthandler_disabled())
+	    if (faulthandler_disabled() || fault_space == 0)
 	    {
 		/* Clean up and return if in exception table. */
 		if (fixup_exception(regs))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/unaligned.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/unaligned.c
@@ -107,7 +107,7 @@
 #define R1(i) (((i)>>21)&0x1f)
 #define R2(i) (((i)>>16)&0x1f)
 #define R3(i) ((i)&0x1f)
-#define FR3(i) ((((i)<<1)&0x1f)|(((i)>>6)&1))
+#define FR3(i) ((((i)&0x1f)<<1)|(((i)>>6)&1))
 #define IM(i,n) (((i)>>1&((1<<(n-1))-1))|((i)&1?((0-1L)<<(n-1)):0))
 #define IM5_2(i) IM((i)>>16,5)
 #define IM5_3(i) IM((i),5)
@@ -340,7 +340,7 @@
 	: "r" (val), "r" (regs->ior), "r" (regs->isr)
 	: "r19", "r20", "r21", "r22", "r1", FIXUP_BRANCH_CLOBBER );
 
-	return 0;
+	return ret;
 }
 static int emulate_std(struct pt_regs *regs, int frreg, int flop)
 {
@@ -397,7 +397,7 @@
 	__asm__ __volatile__ (
 "	mtsp	%4, %%sr1\n"
 "	zdep	%2, 29, 2, %%r19\n"
-"	dep	%%r0, 31, 2, %2\n"
+"	dep	%%r0, 31, 2, %3\n"
 "	mtsar	%%r19\n"
 "	zvdepi	-2, 32, %%r19\n"
 "1:	ldw	0(%%sr1,%3),%%r20\n"
@@ -409,7 +409,7 @@
 "	andcm	%%r21, %%r19, %%r21\n"
 "	or	%1, %%r20, %1\n"
 "	or	%2, %%r21, %2\n"
-"3:	stw	%1,0(%%sr1,%1)\n"
+"3:	stw	%1,0(%%sr1,%3)\n"
 "4:	stw	%%r1,4(%%sr1,%3)\n"
 "5:	stw	%2,8(%%sr1,%3)\n"
 "	copy	%%r0, %0\n"
@@ -596,7 +596,6 @@
 		ret = ERR_NOTHANDLED;	/* "undefined", but lets kill them. */
 		break;
 	}
-#ifdef CONFIG_PA20
 	switch (regs->iir & OPCODE2_MASK)
 	{
 	case OPCODE_FLDD_L:
@@ -607,22 +606,23 @@
 		flop=1;
 		ret = emulate_std(regs, R2(regs->iir),1);
 		break;
+#ifdef CONFIG_PA20
 	case OPCODE_LDD_L:
 		ret = emulate_ldd(regs, R2(regs->iir),0);
 		break;
 	case OPCODE_STD_L:
 		ret = emulate_std(regs, R2(regs->iir),0);
 		break;
-	}
 #endif
+	}
 	switch (regs->iir & OPCODE3_MASK)
 	{
 	case OPCODE_FLDW_L:
 		flop=1;
-		ret = emulate_ldw(regs, R2(regs->iir),0);
+		ret = emulate_ldw(regs, R2(regs->iir), 1);
 		break;
 	case OPCODE_LDW_M:
-		ret = emulate_ldw(regs, R2(regs->iir),1);
+		ret = emulate_ldw(regs, R2(regs->iir), 0);
 		break;
 
 	case OPCODE_FSTW_L:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/kernel/unwind.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/kernel/unwind.c
@@ -21,6 +21,8 @@
 #include <asm/ptrace.h>
 
 #include <asm/unwind.h>
+#include <asm/switch_to.h>
+#include <asm/sections.h>
 
 /* #define DEBUG 1 */
 #ifdef DEBUG
@@ -203,6 +205,11 @@
 	return 0;
 }
 
+static bool pc_is_kernel_fn(unsigned long pc, void *fn)
+{
+	return (unsigned long)dereference_kernel_function_descriptor(fn) == pc;
+}
+
 static int unwind_special(struct unwind_frame_info *info, unsigned long pc, int frame_size)
 {
 	/*
@@ -221,7 +228,7 @@
 	extern void * const _call_on_stack;
 #endif /* CONFIG_IRQSTACKS */
 
-	if (pc == (unsigned long) &handle_interruption) {
+	if (pc_is_kernel_fn(pc, handle_interruption)) {
 		struct pt_regs *regs = (struct pt_regs *)(info->sp - frame_size - PT_SZ_ALGN);
 		dbg("Unwinding through handle_interruption()\n");
 		info->prev_sp = regs->gr[30];
@@ -229,13 +236,13 @@
 		return 1;
 	}
 
-	if (pc == (unsigned long) &ret_from_kernel_thread ||
-	    pc == (unsigned long) &syscall_exit) {
+	if (pc_is_kernel_fn(pc, ret_from_kernel_thread) ||
+	    pc_is_kernel_fn(pc, syscall_exit)) {
 		info->prev_sp = info->prev_ip = 0;
 		return 1;
 	}
 
-	if (pc == (unsigned long) &intr_return) {
+	if (pc_is_kernel_fn(pc, intr_return)) {
 		struct pt_regs *regs;
 
 		dbg("Found intr_return()\n");
@@ -246,20 +253,20 @@
 		return 1;
 	}
 
-	if (pc == (unsigned long) &_switch_to_ret) {
+	if (pc_is_kernel_fn(pc, _switch_to) ||
+	    pc_is_kernel_fn(pc, _switch_to_ret)) {
 		info->prev_sp = info->sp - CALLEE_SAVE_FRAME_SIZE;
 		info->prev_ip = *(unsigned long *)(info->prev_sp - RP_OFFSET);
 		return 1;
 	}
 
 #ifdef CONFIG_IRQSTACKS
-	if (pc == (unsigned long) &_call_on_stack) {
+	if (pc_is_kernel_fn(pc, _call_on_stack)) {
 		info->prev_sp = *(unsigned long *)(info->sp - FRAME_SIZE - REG_SZ);
 		info->prev_ip = *(unsigned long *)(info->sp - FRAME_SIZE - RP_OFFSET);
 		return 1;
 	}
 #endif
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/lib/iomap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/lib/iomap.c
@@ -346,6 +346,16 @@
 	return *((u64 *)addr);
 }
 
+u64 ioread64_lo_hi(const void __iomem *addr)
+{
+	u32 low, high;
+
+	low = ioread32(addr);
+	high = ioread32(addr + sizeof(u32));
+
+	return low + ((u64)high << 32);
+}
+
 u64 ioread64_hi_lo(const void __iomem *addr)
 {
 	u32 low, high;
@@ -419,6 +429,12 @@
 	}
 }
 
+void iowrite64_lo_hi(u64 val, void __iomem *addr)
+{
+	iowrite32(val, addr);
+	iowrite32(val >> 32, addr + sizeof(u32));
+}
+
 void iowrite64_hi_lo(u64 val, void __iomem *addr)
 {
 	iowrite32(val >> 32, addr + sizeof(u32));
@@ -530,6 +546,7 @@
 EXPORT_SYMBOL(ioread32be);
 EXPORT_SYMBOL(ioread64);
 EXPORT_SYMBOL(ioread64be);
+EXPORT_SYMBOL(ioread64_lo_hi);
 EXPORT_SYMBOL(ioread64_hi_lo);
 EXPORT_SYMBOL(iowrite8);
 EXPORT_SYMBOL(iowrite16);
@@ -538,6 +555,7 @@
 EXPORT_SYMBOL(iowrite32be);
 EXPORT_SYMBOL(iowrite64);
 EXPORT_SYMBOL(iowrite64be);
+EXPORT_SYMBOL(iowrite64_lo_hi);
 EXPORT_SYMBOL(iowrite64_hi_lo);
 EXPORT_SYMBOL(ioread8_rep);
 EXPORT_SYMBOL(ioread16_rep);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/mm/fault.c
@@ -424,3 +424,92 @@
 		goto no_context;
 	pagefault_out_of_memory();
 }
+
+/* Handle non-access data TLB miss faults.
+ *
+ * For probe instructions, accesses to userspace are considered allowed
+ * if they lie in a valid VMA and the access type matches. We are not
+ * allowed to handle MM faults here so there may be situations where an
+ * actual access would fail even though a probe was successful.
+ */
+int
+handle_nadtlb_fault(struct pt_regs *regs)
+{
+	unsigned long insn = regs->iir;
+	int breg, treg, xreg, val = 0;
+	struct vm_area_struct *vma, *prev_vma;
+	struct task_struct *tsk;
+	struct mm_struct *mm;
+	unsigned long address;
+	unsigned long acc_type;
+
+	switch (insn & 0x380) {
+	case 0x280:
+		/* FDC instruction */
+		fallthrough;
+	case 0x380:
+		/* PDC and FIC instructions */
+		if (printk_ratelimit()) {
+			pr_warn("BUG: nullifying cache flush/purge instruction\n");
+			show_regs(regs);
+		}
+		if (insn & 0x20) {
+			/* Base modification */
+			breg = (insn >> 21) & 0x1f;
+			xreg = (insn >> 16) & 0x1f;
+			if (breg && xreg)
+				regs->gr[breg] += regs->gr[xreg];
+		}
+		regs->gr[0] |= PSW_N;
+		return 1;
+
+	case 0x180:
+		/* PROBE instruction */
+		treg = insn & 0x1f;
+		if (regs->isr) {
+			tsk = current;
+			mm = tsk->mm;
+			if (mm) {
+				/* Search for VMA */
+				address = regs->ior;
+				mmap_read_lock(mm);
+				vma = find_vma_prev(mm, address, &prev_vma);
+				mmap_read_unlock(mm);
+
+				/*
+				 * Check if access to the VMA is okay.
+				 * We don't allow for stack expansion.
+				 */
+				acc_type = (insn & 0x40) ? VM_WRITE : VM_READ;
+				if (vma
+				    && address >= vma->vm_start
+				    && (vma->vm_flags & acc_type) == acc_type)
+					val = 1;
+			}
+		}
+		if (treg)
+			regs->gr[treg] = val;
+		regs->gr[0] |= PSW_N;
+		return 1;
+
+	case 0x300:
+		/* LPA instruction */
+		if (insn & 0x20) {
+			/* Base modification */
+			breg = (insn >> 21) & 0x1f;
+			xreg = (insn >> 16) & 0x1f;
+			if (breg && xreg)
+				regs->gr[breg] += regs->gr[xreg];
+		}
+		treg = insn & 0x1f;
+		if (treg)
+			regs->gr[treg] = 0;
+		regs->gr[0] |= PSW_N;
+		return 1;
+
+	default:
+		break;
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/mm/fixmap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/mm/fixmap.c
@@ -20,12 +20,9 @@
 	pte_t *pte;
 
 	if (pmd_none(*pmd))
-		pmd = pmd_alloc(NULL, pud, vaddr);
-
-	pte = pte_offset_kernel(pmd, vaddr);
-	if (pte_none(*pte))
 		pte = pte_alloc_kernel(pmd, vaddr);
 
+	pte = pte_offset_kernel(pmd, vaddr);
 	set_pte_at(&init_mm, vaddr, pte, __mk_pte(phys, PAGE_KERNEL_RWX));
 	flush_tlb_kernel_range(vaddr, vaddr + PAGE_SIZE);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/parisc/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/parisc/mm/init.c
@@ -341,9 +341,9 @@
 
 static bool kernel_set_to_readonly;
 
-static void __init map_pages(unsigned long start_vaddr,
-			     unsigned long start_paddr, unsigned long size,
-			     pgprot_t pgprot, int force)
+static void __ref map_pages(unsigned long start_vaddr,
+			    unsigned long start_paddr, unsigned long size,
+			    pgprot_t pgprot, int force)
 {
 	pmd_t *pmd;
 	pte_t *pg_table;
@@ -453,7 +453,7 @@
 	flush_tlb_all();
 }
 
-void __ref free_initmem(void)
+void free_initmem(void)
 {
 	unsigned long init_begin = (unsigned long)__init_begin;
 	unsigned long init_end = (unsigned long)__init_end;
@@ -467,7 +467,6 @@
 	/* The init text pages are marked R-X.  We have to
 	 * flush the icache and mark them RW-
 	 *
-	 * This is tricky, because map_pages is in the init section.
 	 * Do a dummy remap of the data section first (the data
 	 * section is already PAGE_KERNEL) to pull in the TLB entries
 	 * for map_kernel */
@@ -842,9 +841,9 @@
 {
 	int do_recycle;
 
-	__inc_irq_stat(irq_tlb_count);
 	do_recycle = 0;
 	spin_lock(&sid_lock);
+	__inc_irq_stat(irq_tlb_count);
 	if (dirty_space_ids > RECYCLE_THRESHOLD) {
 	    BUG_ON(recycle_inuse);  /* FIXME: Use a semaphore/wait queue here */
 	    get_dirty_sids(&recycle_ndirty,recycle_dirty_array);
@@ -863,8 +862,8 @@
 #else
 void flush_tlb_all(void)
 {
-	__inc_irq_stat(irq_tlb_count);
 	spin_lock(&sid_lock);
+	__inc_irq_stat(irq_tlb_count);
 	flush_tlb_all_local(NULL);
 	recycle_sids();
 	spin_unlock(&sid_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/Kconfig
@@ -138,7 +138,7 @@
 	select ARCH_HAS_PTE_SPECIAL
 	select ARCH_HAS_SCALED_CPUTIME		if VIRT_CPU_ACCOUNTING_NATIVE && PPC_BOOK3S_64
 	select ARCH_HAS_SET_MEMORY
-	select ARCH_HAS_STRICT_KERNEL_RWX	if ((PPC_BOOK3S_64 || PPC32) && !HIBERNATION)
+	select ARCH_HAS_STRICT_KERNEL_RWX	if (PPC_BOOK3S || PPC_8xx || 40x) && !HIBERNATION
 	select ARCH_HAS_STRICT_MODULE_RWX	if ARCH_HAS_STRICT_KERNEL_RWX && !PPC_BOOK3S_32
 	select ARCH_HAS_TICK_BROADCAST		if GENERIC_CLOCKEVENTS_BROADCAST
 	select ARCH_HAS_UACCESS_FLUSHCACHE
@@ -150,7 +150,7 @@
 	select ARCH_OPTIONAL_KERNEL_RWX		if ARCH_HAS_STRICT_KERNEL_RWX
 	select ARCH_STACKWALK
 	select ARCH_SUPPORTS_ATOMIC_RMW
-	select ARCH_SUPPORTS_DEBUG_PAGEALLOC	if PPC32 || PPC_BOOK3S_64
+	select ARCH_SUPPORTS_DEBUG_PAGEALLOC	if PPC_BOOK3S || PPC_8xx || 40x
 	select ARCH_USE_BUILTIN_BSWAP
 	select ARCH_USE_CMPXCHG_LOCKREF		if PPC64
 	select ARCH_USE_MEMTEST
@@ -190,7 +190,7 @@
 	select HAVE_ARCH_JUMP_LABEL_RELATIVE
 	select HAVE_ARCH_KASAN			if PPC32 && PPC_PAGE_SHIFT <= 14
 	select HAVE_ARCH_KASAN_VMALLOC		if PPC32 && PPC_PAGE_SHIFT <= 14
-	select HAVE_ARCH_KFENCE			if PPC32
+	select HAVE_ARCH_KFENCE			if PPC_BOOK3S_32 || PPC_8xx || 40x
 	select HAVE_ARCH_KGDB
 	select HAVE_ARCH_MMAP_RND_BITS
 	select HAVE_ARCH_MMAP_RND_COMPAT_BITS	if COMPAT
@@ -217,7 +217,6 @@
 	select HAVE_HARDLOCKUP_DETECTOR_PERF	if PERF_EVENTS && HAVE_PERF_EVENTS_NMI && !HAVE_HARDLOCKUP_DETECTOR_ARCH
 	select HAVE_HW_BREAKPOINT		if PERF_EVENTS && (PPC_BOOK3S || PPC_8xx)
 	select HAVE_IOREMAP_PROT
-	select HAVE_IRQ_EXIT_ON_IRQ_STACK
 	select HAVE_IRQ_TIME_ACCOUNTING
 	select HAVE_KERNEL_GZIP
 	select HAVE_KERNEL_LZMA			if DEFAULT_UIMAGE
@@ -354,6 +353,10 @@
 	def_bool y
 	depends on PPC_POWERNV || PPC_PSERIES
 
+config ARCH_HAS_ADD_PAGES
+	def_bool y
+	depends on ARCH_ENABLE_MEMORY_HOTPLUG
+
 config PPC_DCR_NATIVE
 	bool
 
@@ -768,7 +771,6 @@
 	range 13 15
 	default "15" if PPC_256K_PAGES
 	default "14" if PPC64
-	default "14" if KASAN
 	default "13"
 	help
 	  Used to define the stack size. The default is almost always what you
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/Kconfig.debug
@@ -240,7 +240,7 @@
 
 config PPC_EARLY_DEBUG_CPM
 	bool "Early serial debugging for Freescale CPM-based serial ports"
-	depends on SERIAL_CPM
+	depends on SERIAL_CPM=y
 	help
 	  Select this to enable early debugging for Freescale chips
 	  using a CPM-based serial port.  This assumes that the bootwrapper
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/Makefile
@@ -17,23 +17,6 @@
 # Set default 32 bits cross compilers for vdso and boot wrapper
 CROSS32_COMPILE ?=
 
-ifeq ($(HAS_BIARCH),y)
-ifeq ($(CROSS32_COMPILE),)
-ifdef CONFIG_PPC32
-# These options will be overridden by any -mcpu option that the CPU
-# or platform code sets later on the command line, but they are needed
-# to set a sane 32-bit cpu target for the 64-bit cross compiler which
-# may default to the wrong ISA.
-KBUILD_CFLAGS		+= -mcpu=powerpc
-KBUILD_AFLAGS		+= -mcpu=powerpc
-endif
-endif
-endif
-
-ifdef CONFIG_PPC_BOOK3S_32
-KBUILD_CFLAGS		+= -mcpu=powerpc
-endif
-
 # If we're on a ppc/ppc64/ppc64le machine use that defconfig, otherwise just use
 # ppc64_defconfig because we have nothing better to go on.
 uname := $(shell uname -m)
@@ -61,18 +44,13 @@
 machine-$(CONFIG_CPU_LITTLE_ENDIAN) += le
 UTS_MACHINE := $(subst $(space),,$(machine-y))
 
-# XXX This needs to be before we override LD below
-ifdef CONFIG_PPC32
-KBUILD_LDFLAGS_MODULE += arch/powerpc/lib/crtsavres.o
-else
-ifeq ($(call ld-ifversion, -ge, 22500, y),y)
+ifeq ($(CONFIG_PPC64)$(CONFIG_LD_IS_BFD),yy)
 # Have the linker provide sfpr if possible.
 # There is a corresponding test in arch/powerpc/lib/Makefile
 KBUILD_LDFLAGS_MODULE += --save-restore-funcs
 else
 KBUILD_LDFLAGS_MODULE += arch/powerpc/lib/crtsavres.o
 endif
-endif
 
 ifdef CONFIG_CPU_LITTLE_ENDIAN
 KBUILD_CFLAGS	+= -mlittle-endian
@@ -109,7 +87,7 @@
 
 ifeq ($(HAS_BIARCH),y)
 KBUILD_CFLAGS	+= -m$(BITS)
-KBUILD_AFLAGS	+= -m$(BITS) -Wl,-a$(BITS)
+KBUILD_AFLAGS	+= -m$(BITS)
 KBUILD_LDFLAGS	+= -m elf$(BITS)$(LDEMULATION)
 endif
 
@@ -171,9 +149,9 @@
 CFLAGS-$(CONFIG_GENERIC_CPU) += $(call cc-option,-mtune=power9,-mtune=power8)
 else
 CFLAGS-$(CONFIG_GENERIC_CPU) += $(call cc-option,-mtune=power7,$(call cc-option,-mtune=power5))
-CFLAGS-$(CONFIG_GENERIC_CPU) += $(call cc-option,-mcpu=power5,-mcpu=power4)
+CFLAGS-$(CONFIG_GENERIC_CPU) += -mcpu=power4
 endif
-else
+else ifdef CONFIG_PPC_BOOK3E_64
 CFLAGS-$(CONFIG_GENERIC_CPU) += -mcpu=powerpc64
 endif
 
@@ -185,6 +163,7 @@
 endif
 
 CFLAGS-$(CONFIG_TARGET_CPU_BOOL) += $(call cc-option,-mcpu=$(CONFIG_TARGET_CPU))
+AFLAGS-$(CONFIG_TARGET_CPU_BOOL) += $(call cc-option,-mcpu=$(CONFIG_TARGET_CPU))
 
 # Altivec option not allowed with e500mc64 in GCC.
 ifdef CONFIG_ALTIVEC
@@ -195,14 +174,6 @@
 CFLAGS-$(CONFIG_E5500_CPU) += $(E5500_CPU)
 CFLAGS-$(CONFIG_E6500_CPU) += $(call cc-option,-mcpu=e6500,$(E5500_CPU))
 
-ifdef CONFIG_PPC32
-ifdef CONFIG_PPC_E500MC
-CFLAGS-y += $(call cc-option,-mcpu=e500mc,-mcpu=powerpc)
-else
-CFLAGS-$(CONFIG_E500) += $(call cc-option,-mcpu=8540 -msoft-float,-mcpu=powerpc)
-endif
-endif
-
 asinstr := $(call as-instr,lis 9$(comma)foo@high,-DHAVE_AS_ATHIGH=1)
 
 KBUILD_CPPFLAGS	+= -I $(srctree)/arch/$(ARCH) $(asinstr)
@@ -272,7 +243,7 @@
 all: zImage
 
 # With make 3.82 we cannot mix normal and wildcard targets
-BOOT_TARGETS1 := zImage zImage.initrd uImage
+BOOT_TARGETS1 := zImage zImage.initrd uImage vmlinux.strip
 BOOT_TARGETS2 := zImage% dtbImage% treeImage.% cuImage.% simpleImage.% uImage.%
 
 PHONY += $(BOOT_TARGETS1) $(BOOT_TARGETS2)
@@ -458,13 +429,12 @@
 endif # CONFIG_SMP
 
 PHONY += checkbin
-# Check toolchain versions:
-# - gcc-4.6 is the minimum kernel-wide version so nothing required.
 checkbin:
-	@if test "x${CONFIG_CPU_LITTLE_ENDIAN}" = "xy" \
-	    && $(LD) --version | head -1 | grep ' 2\.24$$' >/dev/null ; then \
-		echo -n '*** binutils 2.24 miscompiles weak symbols ' ; \
-		echo 'in some circumstances.' ; \
-		echo -n '*** Please use a different binutils version.' ; \
+	@if test "x${CONFIG_FTRACE_MCOUNT_USE_RECORDMCOUNT}" = "xy" -a \
+		"x${CONFIG_LD_IS_BFD}" = "xy" -a \
+		"${CONFIG_LD_VERSION}" = "23700" ; then \
+		echo -n '*** binutils 2.37 drops unused section symbols, which recordmcount ' ; \
+		echo 'is unable to handle.' ; \
+		echo '*** Please use a different binutils version.' ; \
 		false ; \
 	fi
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/Makefile
@@ -34,6 +34,7 @@
 
 BOOTCFLAGS    := -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs \
 		 -fno-strict-aliasing -O2 -msoft-float -mno-altivec -mno-vsx \
+		 $(call cc-option,-mno-spe) $(call cc-option,-mspe=no) \
 		 -pipe -fomit-frame-pointer -fno-builtin -fPIC -nostdinc \
 		 $(LINUXINCLUDE)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/crt0.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/crt0.S
@@ -28,7 +28,7 @@
 p_bss_start:	.8byte	__bss_start
 p_end:		.8byte	_end
 
-p_toc:		.8byte	__toc_start + 0x8000 - p_base
+p_toc:		.8byte	.TOC. - p_base
 p_dyn:		.8byte	__dynamic_start - p_base
 p_rela:		.8byte	__rela_dyn_start - p_base
 p_prom:		.8byte	0
@@ -226,16 +226,19 @@
 #ifdef __powerpc64__
 
 #define PROM_FRAME_SIZE 512
-#define SAVE_GPR(n, base)       std     n,8*(n)(base)
-#define REST_GPR(n, base)       ld      n,8*(n)(base)
-#define SAVE_2GPRS(n, base)     SAVE_GPR(n, base); SAVE_GPR(n+1, base)
-#define SAVE_4GPRS(n, base)     SAVE_2GPRS(n, base); SAVE_2GPRS(n+2, base)
-#define SAVE_8GPRS(n, base)     SAVE_4GPRS(n, base); SAVE_4GPRS(n+4, base)
-#define SAVE_10GPRS(n, base)    SAVE_8GPRS(n, base); SAVE_2GPRS(n+8, base)
-#define REST_2GPRS(n, base)     REST_GPR(n, base); REST_GPR(n+1, base)
-#define REST_4GPRS(n, base)     REST_2GPRS(n, base); REST_2GPRS(n+2, base)
-#define REST_8GPRS(n, base)     REST_4GPRS(n, base); REST_4GPRS(n+4, base)
-#define REST_10GPRS(n, base)    REST_8GPRS(n, base); REST_2GPRS(n+8, base)
+
+.macro OP_REGS op, width, start, end, base, offset
+	.Lreg=\start
+	.rept (\end - \start + 1)
+	\op	.Lreg,\offset+\width*.Lreg(\base)
+	.Lreg=.Lreg+1
+	.endr
+.endm
+
+#define SAVE_GPRS(start, end, base)	OP_REGS std, 8, start, end, base, 0
+#define REST_GPRS(start, end, base)	OP_REGS ld, 8, start, end, base, 0
+#define SAVE_GPR(n, base)		SAVE_GPRS(n, n, base)
+#define REST_GPR(n, base)		REST_GPRS(n, n, base)
 
 /* prom handles the jump into and return from firmware.  The prom args pointer
    is loaded in r3. */
@@ -246,9 +249,7 @@
 	stdu	r1,-PROM_FRAME_SIZE(r1) /* Save SP and create stack space */
 
 	SAVE_GPR(2, r1)
-	SAVE_GPR(13, r1)
-	SAVE_8GPRS(14, r1)
-	SAVE_10GPRS(22, r1)
+	SAVE_GPRS(13, 31, r1)
 	mfcr    r10
 	std     r10,8*32(r1)
 	mfmsr   r10
@@ -283,9 +284,7 @@
 
 	/* Restore other registers */
 	REST_GPR(2, r1)
-	REST_GPR(13, r1)
-	REST_8GPRS(14, r1)
-	REST_10GPRS(22, r1)
+	REST_GPRS(13, 31, r1)
 	ld      r10,8*32(r1)
 	mtcr	r10
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/charon.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/charon.dts
@@ -35,7 +35,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;	// 128MB
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/digsy_mtc.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/digsy_mtc.dts
@@ -16,7 +16,7 @@
 	model = "intercontrol,digsy-mtc";
 	compatible = "intercontrol,digsy-mtc";
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x02000000>;	// 32MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/e500v1_power_isa.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/e500v1_power_isa.dtsi
@@ -0,0 +1,51 @@
+/*
+ * e500v1 Power ISA Device Tree Source (include)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+	cpus {
+		power-isa-version = "2.03";
+		power-isa-b;		// Base
+		power-isa-e;		// Embedded
+		power-isa-atb;		// Alternate Time Base
+		power-isa-cs;		// Cache Specification
+		power-isa-e.le;		// Embedded.Little-Endian
+		power-isa-e.pm;		// Embedded.Performance Monitor
+		power-isa-ecl;		// Embedded Cache Locking
+		power-isa-mmc;		// Memory Coherence
+		power-isa-sp;		// Signal Processing Engine
+		power-isa-sp.fs;	// SPE.Embedded Float Scalar Single
+		power-isa-sp.fv;	// SPE.Embedded Float Vector
+		mmu-type = "power-embedded";
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/mpc8540ads.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/mpc8540ads.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 
-/include/ "e500v2_power_isa.dtsi"
+/include/ "e500v1_power_isa.dtsi"
 
 / {
 	model = "MPC8540ADS";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/mpc8541cds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/mpc8541cds.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 
-/include/ "e500v2_power_isa.dtsi"
+/include/ "e500v1_power_isa.dtsi"
 
 / {
 	model = "MPC8541CDS";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/mpc8555cds.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/mpc8555cds.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 
-/include/ "e500v2_power_isa.dtsi"
+/include/ "e500v1_power_isa.dtsi"
 
 / {
 	model = "MPC8555CDS";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/mpc8560ads.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/mpc8560ads.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 
-/include/ "e500v2_power_isa.dtsi"
+/include/ "e500v1_power_isa.dtsi"
 
 / {
 	model = "MPC8560ADS";
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
+/*
+ * QorIQ FMan v3 10g port #2 device tree stub [ controller @ offset 0x400000 ]
+ *
+ * Copyright 2022 Sean Anderson <sean.anderson@seco.com>
+ * Copyright 2012 - 2015 Freescale Semiconductor Inc.
+ */
+
+fman@400000 {
+	fman0_rx_0x08: port@88000 {
+		cell-index = <0x8>;
+		compatible = "fsl,fman-v3-port-rx";
+		reg = <0x88000 0x1000>;
+		fsl,fman-10g-port;
+	};
+
+	fman0_tx_0x28: port@a8000 {
+		cell-index = <0x28>;
+		compatible = "fsl,fman-v3-port-tx";
+		reg = <0xa8000 0x1000>;
+		fsl,fman-10g-port;
+	};
+
+	ethernet@e0000 {
+		cell-index = <0>;
+		compatible = "fsl,fman-memac";
+		reg = <0xe0000 0x1000>;
+		fsl,fman-ports = <&fman0_rx_0x08 &fman0_tx_0x28>;
+		ptp-timer = <&ptp_timer0>;
+		pcsphy-handle = <&pcsphy0>;
+	};
+
+	mdio@e1000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
+		reg = <0xe1000 0x1000>;
+		fsl,erratum-a011043; /* must ignore read errors */
+
+		pcsphy0: ethernet-phy@0 {
+			reg = <0x0>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
+/*
+ * QorIQ FMan v3 10g port #3 device tree stub [ controller @ offset 0x400000 ]
+ *
+ * Copyright 2022 Sean Anderson <sean.anderson@seco.com>
+ * Copyright 2012 - 2015 Freescale Semiconductor Inc.
+ */
+
+fman@400000 {
+	fman0_rx_0x09: port@89000 {
+		cell-index = <0x9>;
+		compatible = "fsl,fman-v3-port-rx";
+		reg = <0x89000 0x1000>;
+		fsl,fman-10g-port;
+	};
+
+	fman0_tx_0x29: port@a9000 {
+		cell-index = <0x29>;
+		compatible = "fsl,fman-v3-port-tx";
+		reg = <0xa9000 0x1000>;
+		fsl,fman-10g-port;
+	};
+
+	ethernet@e2000 {
+		cell-index = <1>;
+		compatible = "fsl,fman-memac";
+		reg = <0xe2000 0x1000>;
+		fsl,fman-ports = <&fman0_rx_0x09 &fman0_tx_0x29>;
+		ptp-timer = <&ptp_timer0>;
+		pcsphy-handle = <&pcsphy1>;
+	};
+
+	mdio@e3000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
+		reg = <0xe3000 0x1000>;
+		fsl,erratum-a011043; /* must ignore read errors */
+
+		pcsphy1: ethernet-phy@0 {
+			reg = <0x0>;
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/qoriq-fman3l-0.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/qoriq-fman3l-0.dtsi
@@ -79,6 +79,7 @@
 		#size-cells = <0>;
 		compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
 		reg = <0xfc000 0x1000>;
+		fsl,erratum-a009885;
 	};
 
 	xmdio0: mdio@fd000 {
@@ -86,6 +87,7 @@
 		#size-cells = <0>;
 		compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
 		reg = <0xfd000 0x1000>;
+		fsl,erratum-a009885;
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * T1040RDB-REV-A Device Tree Source
+ *
+ * Copyright 2014 - 2015 Freescale Semiconductor Inc.
+ *
+ */
+
+#include "t1040rdb.dts"
+
+/ {
+	model = "fsl,T1040RDB-REV-A";
+};
+
+&seville_port0 {
+	label = "ETH5";
+};
+
+&seville_port2 {
+	label = "ETH7";
+};
+
+&seville_port4 {
+	label = "ETH9";
+};
+
+&seville_port6 {
+	label = "ETH11";
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/t1040rdb.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/t1040rdb.dts
@@ -119,7 +119,7 @@
 	managed = "in-band-status";
 	phy-handle = <&phy_qsgmii_0>;
 	phy-mode = "qsgmii";
-	label = "ETH5";
+	label = "ETH3";
 	status = "okay";
 };
 
@@ -135,7 +135,7 @@
 	managed = "in-band-status";
 	phy-handle = <&phy_qsgmii_2>;
 	phy-mode = "qsgmii";
-	label = "ETH7";
+	label = "ETH5";
 	status = "okay";
 };
 
@@ -151,7 +151,7 @@
 	managed = "in-band-status";
 	phy-handle = <&phy_qsgmii_4>;
 	phy-mode = "qsgmii";
-	label = "ETH9";
+	label = "ETH7";
 	status = "okay";
 };
 
@@ -167,7 +167,7 @@
 	managed = "in-band-status";
 	phy-handle = <&phy_qsgmii_6>;
 	phy-mode = "qsgmii";
-	label = "ETH11";
+	label = "ETH9";
 	status = "okay";
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/t104xrdb.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/t104xrdb.dtsi
@@ -139,12 +139,12 @@
 		fman@400000 {
 			ethernet@e6000 {
 				phy-handle = <&phy_rgmii_0>;
-				phy-connection-type = "rgmii";
+				phy-connection-type = "rgmii-id";
 			};
 
 			ethernet@e8000 {
 				phy-handle = <&phy_rgmii_1>;
-				phy-connection-type = "rgmii";
+				phy-connection-type = "rgmii-id";
 			};
 
 			mdio0: mdio@fc000 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
@@ -609,8 +609,8 @@
 /include/ "qoriq-bman1.dtsi"
 
 /include/ "qoriq-fman3-0.dtsi"
-/include/ "qoriq-fman3-0-1g-0.dtsi"
-/include/ "qoriq-fman3-0-1g-1.dtsi"
+/include/ "qoriq-fman3-0-10g-2.dtsi"
+/include/ "qoriq-fman3-0-10g-3.dtsi"
 /include/ "qoriq-fman3-0-1g-2.dtsi"
 /include/ "qoriq-fman3-0-1g-3.dtsi"
 /include/ "qoriq-fman3-0-1g-4.dtsi"
@@ -659,3 +659,19 @@
 		interrupts = <16 2 1 9>;
 	};
 };
+
+&fman0_rx_0x08 {
+	/delete-property/ fsl,fman-10g-port;
+};
+
+&fman0_tx_0x28 {
+	/delete-property/ fsl,fman-10g-port;
+};
+
+&fman0_rx_0x09 {
+	/delete-property/ fsl,fman-10g-port;
+};
+
+&fman0_tx_0x29 {
+	/delete-property/ fsl,fman-10g-port;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/lite5200.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/lite5200.dts
@@ -32,7 +32,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x04000000>;	// 64MB
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/lite5200b.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/lite5200b.dts
@@ -31,7 +31,7 @@
 		led4 { gpios = <&gpio_simple 2 1>; };
 	};
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x10000000>;	// 256MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/media5200.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/media5200.dts
@@ -32,7 +32,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x08000000>;	// 128MB RAM
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/mpc5200b.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/mpc5200b.dtsi
@@ -33,7 +33,7 @@
 		};
 	};
 
-	memory: memory {
+	memory: memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x04000000>;	// 64MB
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/o2d.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/o2d.dts
@@ -12,7 +12,7 @@
 	model = "ifm,o2d";
 	compatible = "ifm,o2d";
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x08000000>;  // 128MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/o2d.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/o2d.dtsi
@@ -19,7 +19,7 @@
 	model = "ifm,o2d";
 	compatible = "ifm,o2d";
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x04000000>;	// 64MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/o2dnt2.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/o2dnt2.dts
@@ -12,7 +12,7 @@
 	model = "ifm,o2dnt2";
 	compatible = "ifm,o2d";
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x08000000>;  // 128MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/o3dnt.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/o3dnt.dts
@@ -12,7 +12,7 @@
 	model = "ifm,o3dnt";
 	compatible = "ifm,o2d";
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x04000000>;  // 64MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/pcm032.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/pcm032.dts
@@ -20,7 +20,7 @@
 	model = "phytec,pcm032";
 	compatible = "phytec,pcm032";
 
-	memory {
+	memory@0 {
 		reg = <0x00000000 0x08000000>;	// 128MB
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/dts/tqm5200.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/dts/tqm5200.dts
@@ -32,7 +32,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x04000000>;	// 64MB
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/simple_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/simple_alloc.c
@@ -114,8 +114,11 @@
 		return ptr;
 
 	new = simple_malloc(size);
-	memcpy(new, ptr, p->size);
-	simple_free(ptr);
+	if (new) {
+		memcpy(new, ptr, p->size);
+		simple_free(ptr);
+	}
+
 	return new;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/boot/zImage.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/boot/zImage.lds.S
@@ -36,12 +36,9 @@
   }
 
 #ifdef CONFIG_PPC64_BOOT_WRAPPER
-  . = ALIGN(256);
-  .got :
+  .got : ALIGN(256)
   {
-    __toc_start = .;
-    *(.got)
-    *(.toc)
+    *(.got .toc)
   }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/configs/85xx-hw.config
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/configs/85xx-hw.config
@@ -24,6 +24,7 @@
 CONFIG_FSL_CORENET_CF=y
 CONFIG_FSL_DMA=y
 CONFIG_FSL_HV_MANAGER=y
+CONFIG_FSL_IFC=y
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_FSL_RIO=y
 CONFIG_FSL_XGMAC_MDIO=y
@@ -58,6 +59,7 @@
 CONFIG_MARVELL_PHY=y
 CONFIG_MDIO_BUS_MUX_GPIO=y
 CONFIG_MDIO_BUS_MUX_MMIOREG=y
+CONFIG_MEMORY=y
 CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/configs/ppc6xx_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/configs/ppc6xx_defconfig
@@ -243,8 +243,6 @@
 CONFIG_ATM_BR2684=m
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
-CONFIG_DECNET_ROUTER=y
 CONFIG_ATALK=m
 CONFIG_DEV_APPLETALK=m
 CONFIG_IPDDP=m
@@ -1022,7 +1020,6 @@
 CONFIG_NFSD_V3_ACL=y
 CONFIG_NFSD_V4=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_UPCALL=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/configs/pseries_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/configs/pseries_defconfig
@@ -41,6 +41,7 @@
 CONFIG_SCANLOG=m
 CONFIG_PPC_SMLPAR=y
 CONFIG_IBMEBUS=y
+CONFIG_LIBNVDIMM=m
 CONFIG_PAPR_SCM=m
 CONFIG_PPC_SVM=y
 # CONFIG_PPC_PMAC is not set
@@ -190,7 +191,6 @@
 CONFIG_VIRTIO_CONSOLE=m
 CONFIG_IBM_BSR=m
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=1024
 CONFIG_I2C_CHARDEV=y
 CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/crypto/md5-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/crypto/md5-asm.S
@@ -38,15 +38,11 @@
 
 #define INITIALIZE \
 	PPC_STLU r1,-INT_FRAME_SIZE(r1); \
-	SAVE_8GPRS(14, r1);		/* push registers onto stack	*/ \
-	SAVE_4GPRS(22, r1);						   \
-	SAVE_GPR(26, r1)
+	SAVE_GPRS(14, 26, r1)		/* push registers onto stack	*/
 
 #define FINALIZE \
-	REST_8GPRS(14, r1);		/* pop registers from stack	*/ \
-	REST_4GPRS(22, r1);						   \
-	REST_GPR(26, r1);						   \
-	addi	r1,r1,INT_FRAME_SIZE;
+	REST_GPRS(14, 26, r1);		/* pop registers from stack	*/ \
+	addi	r1,r1,INT_FRAME_SIZE
 
 #ifdef __BIG_ENDIAN__
 #define LOAD_DATA(reg, off) \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/crypto/sha1-powerpc-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/crypto/sha1-powerpc-asm.S
@@ -125,8 +125,7 @@
 
 _GLOBAL(powerpc_sha_transform)
 	PPC_STLU r1,-INT_FRAME_SIZE(r1)
-	SAVE_8GPRS(14, r1)
-	SAVE_10GPRS(22, r1)
+	SAVE_GPRS(14, 31, r1)
 
 	/* Load up A - E */
 	lwz	RA(0),0(r3)	/* A */
@@ -184,7 +183,6 @@
 	stw	RD(0),12(r3)
 	stw	RE(0),16(r3)
 
-	REST_8GPRS(14, r1)
-	REST_10GPRS(22, r1)
+	REST_GPRS(14, 31, r1)
 	addi	r1,r1,INT_FRAME_SIZE
 	blr
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/archrandom.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/archrandom.h
@@ -38,12 +38,7 @@
 #endif /* CONFIG_ARCH_RANDOM */
 
 #ifdef CONFIG_PPC_POWERNV
-int powernv_hwrng_present(void);
 int powernv_get_random_long(unsigned long *v);
-int powernv_get_random_real_mode(unsigned long *v);
-#else
-static inline int powernv_hwrng_present(void) { return 0; }
-static inline int powernv_get_random_real_mode(unsigned long *v) { return 0; }
 #endif
 
 #endif /* _ASM_POWERPC_ARCHRANDOM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/book3s/32/kup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/book3s/32/kup.h
@@ -12,7 +12,6 @@
 #include <linux/jump_label.h>
 
 extern struct static_key_false disable_kuap_key;
-extern struct static_key_false disable_kuep_key;
 
 static __always_inline bool kuap_is_disabled(void)
 {
@@ -21,41 +20,7 @@
 
 static __always_inline bool kuep_is_disabled(void)
 {
-	return !IS_ENABLED(CONFIG_PPC_KUEP) || static_branch_unlikely(&disable_kuep_key);
-}
-
-static inline void kuep_lock(void)
-{
-	if (kuep_is_disabled())
-		return;
-
-	update_user_segments(mfsr(0) | SR_NX);
-	/*
-	 * This isync() shouldn't be necessary as the kernel is not excepted to
-	 * run any instruction in userspace soon after the update of segments,
-	 * but hash based cores (at least G3) seem to exhibit a random
-	 * behaviour when the 'isync' is not there. 603 cores don't have this
-	 * behaviour so don't do the 'isync' as it saves several CPU cycles.
-	 */
-	if (mmu_has_feature(MMU_FTR_HPTE_TABLE))
-		isync();	/* Context sync required after mtsr() */
-}
-
-static inline void kuep_unlock(void)
-{
-	if (kuep_is_disabled())
-		return;
-
-	update_user_segments(mfsr(0) & ~SR_NX);
-	/*
-	 * This isync() shouldn't be necessary as a 'rfi' will soon be executed
-	 * to return to userspace, but hash based cores (at least G3) seem to
-	 * exhibit a random behaviour when the 'isync' is not there. 603 cores
-	 * don't have this behaviour so don't do the 'isync' as it saves several
-	 * CPU cycles.
-	 */
-	if (mmu_has_feature(MMU_FTR_HPTE_TABLE))
-		isync();	/* Context sync required after mtsr() */
+	return !IS_ENABLED(CONFIG_PPC_KUEP);
 }
 
 #ifdef CONFIG_PPC_KUAP
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/book3s/32/mmu-hash.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/book3s/32/mmu-hash.h
@@ -64,7 +64,82 @@
 #define SR_KP	0x20000000	/* User key */
 #define SR_KS	0x40000000	/* Supervisor key */
 
-#ifndef __ASSEMBLY__
+#ifdef __ASSEMBLY__
+
+#include <asm/asm-offsets.h>
+
+.macro uus_addi sr reg1 reg2 imm
+	.if NUM_USER_SEGMENTS > \sr
+	addi	\reg1,\reg2,\imm
+	.endif
+.endm
+
+.macro uus_mtsr sr reg1
+	.if NUM_USER_SEGMENTS > \sr
+	mtsr	\sr, \reg1
+	.endif
+.endm
+
+/*
+ * This isync() shouldn't be necessary as the kernel is not excepted to run
+ * any instruction in userspace soon after the update of segments and 'rfi'
+ * instruction is used to return to userspace, but hash based cores
+ * (at least G3) seem to exhibit a random behaviour when the 'isync' is not
+ * there. 603 cores don't have this behaviour so don't do the 'isync' as it
+ * saves several CPU cycles.
+ */
+.macro uus_isync
+#ifdef CONFIG_PPC_BOOK3S_604
+BEGIN_MMU_FTR_SECTION
+	isync
+END_MMU_FTR_SECTION_IFSET(MMU_FTR_HPTE_TABLE)
+#endif
+.endm
+
+.macro update_user_segments_by_4 tmp1 tmp2 tmp3 tmp4
+	uus_addi	1, \tmp2, \tmp1, 0x111
+	uus_addi	2, \tmp3, \tmp1, 0x222
+	uus_addi	3, \tmp4, \tmp1, 0x333
+
+	uus_mtsr	0, \tmp1
+	uus_mtsr	1, \tmp2
+	uus_mtsr	2, \tmp3
+	uus_mtsr	3, \tmp4
+
+	uus_addi	4, \tmp1, \tmp1, 0x444
+	uus_addi	5, \tmp2, \tmp2, 0x444
+	uus_addi	6, \tmp3, \tmp3, 0x444
+	uus_addi	7, \tmp4, \tmp4, 0x444
+
+	uus_mtsr	4, \tmp1
+	uus_mtsr	5, \tmp2
+	uus_mtsr	6, \tmp3
+	uus_mtsr	7, \tmp4
+
+	uus_addi	8, \tmp1, \tmp1, 0x444
+	uus_addi	9, \tmp2, \tmp2, 0x444
+	uus_addi	10, \tmp3, \tmp3, 0x444
+	uus_addi	11, \tmp4, \tmp4, 0x444
+
+	uus_mtsr	8, \tmp1
+	uus_mtsr	9, \tmp2
+	uus_mtsr	10, \tmp3
+	uus_mtsr	11, \tmp4
+
+	uus_addi	12, \tmp1, \tmp1, 0x444
+	uus_addi	13, \tmp2, \tmp2, 0x444
+	uus_addi	14, \tmp3, \tmp3, 0x444
+	uus_addi	15, \tmp4, \tmp4, 0x444
+
+	uus_mtsr	12, \tmp1
+	uus_mtsr	13, \tmp2
+	uus_mtsr	14, \tmp3
+	uus_mtsr	15, \tmp4
+
+	uus_isync
+.endm
+
+#else
 
 /*
  * This macro defines the mapping from contexts to VSIDs (virtual
@@ -143,6 +218,8 @@
 	update_user_segment(15, val);
 }
 
+int __init find_free_bat(void);
+unsigned int bat_block_size(unsigned long base, unsigned long top);
 #endif /* !__ASSEMBLY__ */
 
 /* We happily ignore the smaller BATs on 601, we don't actually use
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/book3s/32/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/book3s/32/pgtable.h
@@ -178,6 +178,7 @@
 #ifndef __ASSEMBLY__
 
 int map_kernel_page(unsigned long va, phys_addr_t pa, pgprot_t prot);
+void unmap_kernel_page(unsigned long va);
 
 #endif /* !__ASSEMBLY__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/book3s/64/hash-4k.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/book3s/64/hash-4k.h
@@ -90,6 +90,34 @@
 #endif
 
 /*
+ * With 4K page size the real_pte machinery is all nops.
+ */
+static inline real_pte_t __real_pte(pte_t pte, pte_t *ptep, int offset)
+{
+	return (real_pte_t){pte};
+}
+
+#define __rpte_to_pte(r)	((r).pte)
+
+static inline unsigned long __rpte_to_hidx(real_pte_t rpte, unsigned long index)
+{
+	return pte_val(__rpte_to_pte(rpte)) >> H_PAGE_F_GIX_SHIFT;
+}
+
+#define pte_iterate_hashed_subpages(rpte, psize, va, index, shift)       \
+	do {							         \
+		index = 0;					         \
+		shift = mmu_psize_defs[psize].shift;		         \
+
+#define pte_iterate_hashed_end() } while(0)
+
+/*
+ * We expect this to be called only for user addresses or kernel virtual
+ * addresses other than the linear mapping.
+ */
+#define pte_pagesize_index(mm, addr, pte)	MMU_PAGE_4K
+
+/*
  * 4K PTE format is different from 64K PTE format. Saving the hash_slot is just
  * a matter of returning the PTE bits that need to be modified. On 64K PTE,
  * things are a little more involved and hence needs many more parameters to
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/book3s/64/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/book3s/64/pgtable.h
@@ -336,32 +336,6 @@
 
 #ifndef __ASSEMBLY__
 
-/*
- * This is the default implementation of various PTE accessors, it's
- * used in all cases except Book3S with 64K pages where we have a
- * concept of sub-pages
- */
-#ifndef __real_pte
-
-#define __real_pte(e, p, o)		((real_pte_t){(e)})
-#define __rpte_to_pte(r)	((r).pte)
-#define __rpte_to_hidx(r,index)	(pte_val(__rpte_to_pte(r)) >> H_PAGE_F_GIX_SHIFT)
-
-#define pte_iterate_hashed_subpages(rpte, psize, va, index, shift)       \
-	do {							         \
-		index = 0;					         \
-		shift = mmu_psize_defs[psize].shift;		         \
-
-#define pte_iterate_hashed_end() } while(0)
-
-/*
- * We expect this to be called only for user addresses or kernel virtual
- * addresses other than the linear mapping.
- */
-#define pte_pagesize_index(mm, addr, pte)	MMU_PAGE_4K
-
-#endif /* __real_pte */
-
 static inline unsigned long pte_update(struct mm_struct *mm, unsigned long addr,
 				       pte_t *ptep, unsigned long clr,
 				       unsigned long set, int huge)
@@ -1082,6 +1056,8 @@
 	return hash__map_kernel_page(ea, pa, prot);
 }
 
+void unmap_kernel_page(unsigned long va);
+
 static inline int __meminit vmemmap_create_mapping(unsigned long start,
 						   unsigned long page_size,
 						   unsigned long phys)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/bpf_perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/bpf_perf_event.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_POWERPC_BPF_PERF_EVENT_H
+#define _ASM_POWERPC_BPF_PERF_EVENT_H
+
+#include <asm/ptrace.h>
+
+typedef struct user_pt_regs bpf_user_pt_regs_t;
+
+#endif /* _ASM_POWERPC_BPF_PERF_EVENT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/bug.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/bug.h
@@ -13,7 +13,8 @@
 #ifdef CONFIG_DEBUG_BUGVERBOSE
 .macro EMIT_BUG_ENTRY addr,file,line,flags
 	 .section __bug_table,"aw"
-5001:	 .4byte \addr - 5001b, 5002f - 5001b
+5001:	 .4byte \addr - .
+	 .4byte 5002f - .
 	 .short \line, \flags
 	 .org 5001b+BUG_ENTRY_SIZE
 	 .previous
@@ -24,7 +25,7 @@
 #else
 .macro EMIT_BUG_ENTRY addr,file,line,flags
 	 .section __bug_table,"aw"
-5001:	 .4byte \addr - 5001b
+5001:	 .4byte \addr - .
 	 .short \flags
 	 .org 5001b+BUG_ENTRY_SIZE
 	 .previous
@@ -42,15 +43,16 @@
 #ifdef CONFIG_DEBUG_BUGVERBOSE
 #define _EMIT_BUG_ENTRY				\
 	".section __bug_table,\"aw\"\n"		\
-	"2:\t.4byte 1b - 2b, %0 - 2b\n"		\
-	"\t.short %1, %2\n"			\
+	"2:	.4byte 1b - .\n"		\
+	"	.4byte %0 - .\n"		\
+	"	.short %1, %2\n"		\
 	".org 2b+%3\n"				\
 	".previous\n"
 #else
 #define _EMIT_BUG_ENTRY				\
 	".section __bug_table,\"aw\"\n"		\
-	"2:\t.4byte 1b - 2b\n"			\
-	"\t.short %2\n"				\
+	"2:	.4byte 1b - .\n"		\
+	"	.short %2\n"			\
 	".org 2b+%3\n"				\
 	".previous\n"
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/cputhreads.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/cputhreads.h
@@ -3,6 +3,7 @@
 #define _ASM_POWERPC_CPUTHREADS_H
 
 #ifndef __ASSEMBLY__
+#include <asm/cpu_has_feature.h>
 #include <linux/cpumask.h>
 #include <asm/cpu_has_feature.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/dtl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/dtl.h
@@ -1,8 +1,8 @@
 #ifndef _ASM_POWERPC_DTL_H
 #define _ASM_POWERPC_DTL_H
 
+#include <linux/rwsem.h>
 #include <asm/lppaca.h>
-#include <linux/spinlock_types.h>
 
 /*
  * Layout of entries in the hypervisor's dispatch trace log buffer.
@@ -35,7 +35,7 @@
 #define DTL_LOG_ALL		(DTL_LOG_CEDE | DTL_LOG_PREEMPT | DTL_LOG_FAULT)
 
 extern struct kmem_cache *dtl_cache;
-extern rwlock_t dtl_access_lock;
+extern struct rw_semaphore dtl_access_lock;
 
 /*
  * When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE = y, the cpu accounting code controls
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/fadump-internal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/fadump-internal.h
@@ -19,11 +19,6 @@
 
 #define memblock_num_regions(memblock_type)	(memblock.memblock_type.cnt)
 
-/* Alignment per CMA requirement. */
-#define FADUMP_CMA_ALIGNMENT	(PAGE_SIZE <<				\
-				 max_t(unsigned long, MAX_ORDER - 1,	\
-				 pageblock_order))
-
 /* FAD commands */
 #define FADUMP_REGISTER			1
 #define FADUMP_UNREGISTER		2
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/fixmap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/fixmap.h
@@ -111,8 +111,10 @@
 		BUILD_BUG_ON(idx >= __end_of_fixed_addresses);
 	else if (WARN_ON(idx >= __end_of_fixed_addresses))
 		return;
-
-	map_kernel_page(__fix_to_virt(idx), phys, flags);
+	if (pgprot_val(flags))
+		map_kernel_page(__fix_to_virt(idx), phys, flags);
+	else
+		unmap_kernel_page(__fix_to_virt(idx));
 }
 
 #define __early_set_fixmap	__set_fixmap
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/ftrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/ftrace.h
@@ -96,7 +96,7 @@
 #endif /* PPC64_ELF_ABI_v1 */
 #endif /* CONFIG_FTRACE_SYSCALLS */
 
-#ifdef CONFIG_PPC64
+#if defined(CONFIG_PPC64) && defined(CONFIG_FUNCTION_TRACER)
 #include <asm/paca.h>
 
 static inline void this_cpu_disable_ftrace(void)
@@ -120,11 +120,13 @@
 	return get_paca()->ftrace_enabled;
 }
 
+void ftrace_free_init_tramp(void);
 #else /* CONFIG_PPC64 */
 static inline void this_cpu_disable_ftrace(void) { }
 static inline void this_cpu_enable_ftrace(void) { }
 static inline void this_cpu_set_ftrace_enabled(u8 ftrace_enabled) { }
 static inline u8 this_cpu_get_ftrace_enabled(void) { return 1; }
+static inline void ftrace_free_init_tramp(void) { }
 #endif /* CONFIG_PPC64 */
 #endif /* !__ASSEMBLY__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/hvcall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/hvcall.h
@@ -472,7 +472,7 @@
  * Used for all but the craziest of phyp interfaces (see plpar_hcall9)
  */
 #define PLPAR_HCALL_BUFSIZE 4
-long plpar_hcall(unsigned long opcode, unsigned long *retbuf, ...);
+long plpar_hcall(unsigned long opcode, unsigned long retbuf[static PLPAR_HCALL_BUFSIZE], ...);
 
 /**
  * plpar_hcall_raw: - Make a hypervisor call without calculating hcall stats
@@ -486,7 +486,7 @@
  * plpar_hcall, but plpar_hcall_raw works in real mode and does not
  * calculate hypervisor call statistics.
  */
-long plpar_hcall_raw(unsigned long opcode, unsigned long *retbuf, ...);
+long plpar_hcall_raw(unsigned long opcode, unsigned long retbuf[static PLPAR_HCALL_BUFSIZE], ...);
 
 /**
  * plpar_hcall9: - Make a pseries hypervisor call with up to 9 return arguments
@@ -497,8 +497,8 @@
  * PLPAR_HCALL9_BUFSIZE to size the return argument buffer.
  */
 #define PLPAR_HCALL9_BUFSIZE 9
-long plpar_hcall9(unsigned long opcode, unsigned long *retbuf, ...);
-long plpar_hcall9_raw(unsigned long opcode, unsigned long *retbuf, ...);
+long plpar_hcall9(unsigned long opcode, unsigned long retbuf[static PLPAR_HCALL9_BUFSIZE], ...);
+long plpar_hcall9_raw(unsigned long opcode, unsigned long retbuf[static PLPAR_HCALL9_BUFSIZE], ...);
 
 struct hvcall_mpp_data {
 	unsigned long entitled_mem;
@@ -513,7 +513,7 @@
 	unsigned long backing_mem;
 };
 
-int h_get_mpp(struct hvcall_mpp_data *);
+long h_get_mpp(struct hvcall_mpp_data *mpp_data);
 
 struct hvcall_mpp_x_data {
 	unsigned long coalesced_bytes;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/hw_irq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/hw_irq.h
@@ -224,6 +224,42 @@
 	return arch_irqs_disabled_flags(arch_local_save_flags());
 }
 
+static inline void set_pmi_irq_pending(void)
+{
+	/*
+	 * Invoked from PMU callback functions to set PMI bit in the paca.
+	 * This has to be called with irq's disabled (via hard_irq_disable()).
+	 */
+	if (IS_ENABLED(CONFIG_PPC_IRQ_SOFT_MASK_DEBUG))
+		WARN_ON_ONCE(mfmsr() & MSR_EE);
+
+	get_paca()->irq_happened |= PACA_IRQ_PMI;
+}
+
+static inline void clear_pmi_irq_pending(void)
+{
+	/*
+	 * Invoked from PMU callback functions to clear the pending PMI bit
+	 * in the paca.
+	 */
+	if (IS_ENABLED(CONFIG_PPC_IRQ_SOFT_MASK_DEBUG))
+		WARN_ON_ONCE(mfmsr() & MSR_EE);
+
+	get_paca()->irq_happened &= ~PACA_IRQ_PMI;
+}
+
+static inline bool pmi_irq_pending(void)
+{
+	/*
+	 * Invoked from PMU callback functions to check if there is a pending
+	 * PMI bit in the paca.
+	 */
+	if (get_paca()->irq_happened & PACA_IRQ_PMI)
+		return true;
+
+	return false;
+}
+
 #ifdef CONFIG_PPC_BOOK3S
 /*
  * To support disabling and enabling of irq with PMI, set of
@@ -408,6 +444,10 @@
 	BUILD_BUG();
 }
 
+static inline void clear_pmi_irq_pending(void) { }
+static inline void set_pmi_irq_pending(void) { }
+static inline bool pmi_irq_pending(void) { return false; }
+
 static inline void irq_soft_mask_regs_set_state(struct pt_regs *regs, unsigned long val)
 {
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/imc-pmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/imc-pmu.h
@@ -137,7 +137,7 @@
  * are inited.
  */
 struct imc_pmu_ref {
-	struct mutex lock;
+	spinlock_t lock;
 	unsigned int id;
 	int refc;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/interrupt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/interrupt.h
@@ -139,12 +139,10 @@
 	if (!arch_irq_disabled_regs(regs))
 		trace_hardirqs_off();
 
-	if (user_mode(regs)) {
-		kuep_lock();
+	if (user_mode(regs))
 		account_cpu_user_entry();
-	} else {
+	else
 		kuap_save_and_lock(regs);
-	}
 #endif
 
 #ifdef CONFIG_PPC64
@@ -287,18 +285,24 @@
 	/*
 	 * Do not use nmi_enter() for pseries hash guest taking a real-mode
 	 * NMI because not everything it touches is within the RMA limit.
+	 *
+	 * Likewise, do not use it in real mode if percpu first chunk is not
+	 * embedded. With CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK enabled there
+	 * are chances where percpu allocation can come from vmalloc area.
 	 */
-	if (!IS_ENABLED(CONFIG_PPC_BOOK3S_64) ||
+	if ((!IS_ENABLED(CONFIG_PPC_BOOK3S_64) ||
 			!firmware_has_feature(FW_FEATURE_LPAR) ||
-			radix_enabled() || (mfmsr() & MSR_DR))
+			radix_enabled() || (mfmsr() & MSR_DR)) &&
+			!percpu_first_chunk_is_paged)
 		nmi_enter();
 }
 
 static inline void interrupt_nmi_exit_prepare(struct pt_regs *regs, struct interrupt_nmi_state *state)
 {
-	if (!IS_ENABLED(CONFIG_PPC_BOOK3S_64) ||
+	if ((!IS_ENABLED(CONFIG_PPC_BOOK3S_64) ||
 			!firmware_has_feature(FW_FEATURE_LPAR) ||
-			radix_enabled() || (mfmsr() & MSR_DR))
+			radix_enabled() || (mfmsr() & MSR_DR)) &&
+			!percpu_first_chunk_is_paged)
 		nmi_exit();
 
 	/*
@@ -567,7 +571,7 @@
 DECLARE_INTERRUPT_HANDLER(do_bad_slb_fault);
 
 /* hash_utils.c */
-DECLARE_INTERRUPT_HANDLER_RAW(do_hash_fault);
+DECLARE_INTERRUPT_HANDLER(do_hash_fault);
 
 /* fault.c */
 DECLARE_INTERRUPT_HANDLER(do_page_fault);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/io.h
@@ -45,7 +45,7 @@
  * define properly based on the platform
  */
 #ifndef CONFIG_PCI
-#define _IO_BASE	0
+#define _IO_BASE	POISON_POINTER_DELTA
 #define _ISA_MEM_BASE	0
 #define PCI_DRAM_OFFSET 0
 #elif defined(CONFIG_PPC32)
@@ -359,25 +359,37 @@
  */
 static inline void __raw_rm_writeb(u8 val, volatile void __iomem *paddr)
 {
-	__asm__ __volatile__("stbcix %0,0,%1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      stbcix %0,0,%1;  \
+			      .machine pop;"
 		: : "r" (val), "r" (paddr) : "memory");
 }
 
 static inline void __raw_rm_writew(u16 val, volatile void __iomem *paddr)
 {
-	__asm__ __volatile__("sthcix %0,0,%1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      sthcix %0,0,%1;  \
+			      .machine pop;"
 		: : "r" (val), "r" (paddr) : "memory");
 }
 
 static inline void __raw_rm_writel(u32 val, volatile void __iomem *paddr)
 {
-	__asm__ __volatile__("stwcix %0,0,%1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      stwcix %0,0,%1;  \
+			      .machine pop;"
 		: : "r" (val), "r" (paddr) : "memory");
 }
 
 static inline void __raw_rm_writeq(u64 val, volatile void __iomem *paddr)
 {
-	__asm__ __volatile__("stdcix %0,0,%1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      stdcix %0,0,%1;  \
+			      .machine pop;"
 		: : "r" (val), "r" (paddr) : "memory");
 }
 
@@ -389,7 +401,10 @@
 static inline u8 __raw_rm_readb(volatile void __iomem *paddr)
 {
 	u8 ret;
-	__asm__ __volatile__("lbzcix %0,0, %1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      lbzcix %0,0, %1; \
+			      .machine pop;"
 			     : "=r" (ret) : "r" (paddr) : "memory");
 	return ret;
 }
@@ -397,7 +412,10 @@
 static inline u16 __raw_rm_readw(volatile void __iomem *paddr)
 {
 	u16 ret;
-	__asm__ __volatile__("lhzcix %0,0, %1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      lhzcix %0,0, %1; \
+			      .machine pop;"
 			     : "=r" (ret) : "r" (paddr) : "memory");
 	return ret;
 }
@@ -405,7 +423,10 @@
 static inline u32 __raw_rm_readl(volatile void __iomem *paddr)
 {
 	u32 ret;
-	__asm__ __volatile__("lwzcix %0,0, %1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      lwzcix %0,0, %1; \
+			      .machine pop;"
 			     : "=r" (ret) : "r" (paddr) : "memory");
 	return ret;
 }
@@ -413,7 +434,10 @@
 static inline u64 __raw_rm_readq(volatile void __iomem *paddr)
 {
 	u64 ret;
-	__asm__ __volatile__("ldcix %0,0, %1"
+	__asm__ __volatile__(".machine push;   \
+			      .machine power6; \
+			      ldcix %0,0, %1;  \
+			      .machine pop;"
 			     : "=r" (ret) : "r" (paddr) : "memory");
 	return ret;
 }
@@ -532,12 +556,12 @@
 #define __do_inw(port)		_rec_inw(port)
 #define __do_inl(port)		_rec_inl(port)
 #else /* CONFIG_PPC32 */
-#define __do_outb(val, port)	writeb(val,(PCI_IO_ADDR)_IO_BASE+port);
-#define __do_outw(val, port)	writew(val,(PCI_IO_ADDR)_IO_BASE+port);
-#define __do_outl(val, port)	writel(val,(PCI_IO_ADDR)_IO_BASE+port);
-#define __do_inb(port)		readb((PCI_IO_ADDR)_IO_BASE + port);
-#define __do_inw(port)		readw((PCI_IO_ADDR)_IO_BASE + port);
-#define __do_inl(port)		readl((PCI_IO_ADDR)_IO_BASE + port);
+#define __do_outb(val, port)	writeb(val,(PCI_IO_ADDR)(_IO_BASE+port));
+#define __do_outw(val, port)	writew(val,(PCI_IO_ADDR)(_IO_BASE+port));
+#define __do_outl(val, port)	writel(val,(PCI_IO_ADDR)(_IO_BASE+port));
+#define __do_inb(port)		readb((PCI_IO_ADDR)(_IO_BASE + port));
+#define __do_inw(port)		readw((PCI_IO_ADDR)(_IO_BASE + port));
+#define __do_inl(port)		readl((PCI_IO_ADDR)(_IO_BASE + port));
 #endif /* !CONFIG_PPC32 */
 
 #ifdef CONFIG_EEH
@@ -553,12 +577,12 @@
 #define __do_writesw(a, b, n)	_outsw(PCI_FIX_ADDR(a),(b),(n))
 #define __do_writesl(a, b, n)	_outsl(PCI_FIX_ADDR(a),(b),(n))
 
-#define __do_insb(p, b, n)	readsb((PCI_IO_ADDR)_IO_BASE+(p), (b), (n))
-#define __do_insw(p, b, n)	readsw((PCI_IO_ADDR)_IO_BASE+(p), (b), (n))
-#define __do_insl(p, b, n)	readsl((PCI_IO_ADDR)_IO_BASE+(p), (b), (n))
-#define __do_outsb(p, b, n)	writesb((PCI_IO_ADDR)_IO_BASE+(p),(b),(n))
-#define __do_outsw(p, b, n)	writesw((PCI_IO_ADDR)_IO_BASE+(p),(b),(n))
-#define __do_outsl(p, b, n)	writesl((PCI_IO_ADDR)_IO_BASE+(p),(b),(n))
+#define __do_insb(p, b, n)	readsb((PCI_IO_ADDR)(_IO_BASE+(p)), (b), (n))
+#define __do_insw(p, b, n)	readsw((PCI_IO_ADDR)(_IO_BASE+(p)), (b), (n))
+#define __do_insl(p, b, n)	readsl((PCI_IO_ADDR)(_IO_BASE+(p)), (b), (n))
+#define __do_outsb(p, b, n)	writesb((PCI_IO_ADDR)(_IO_BASE+(p)),(b),(n))
+#define __do_outsw(p, b, n)	writesw((PCI_IO_ADDR)(_IO_BASE+(p)),(b),(n))
+#define __do_outsl(p, b, n)	writesl((PCI_IO_ADDR)(_IO_BASE+(p)),(b),(n))
 
 #define __do_memset_io(addr, c, n)	\
 				_memset_io(PCI_FIX_ADDR(addr), c, n)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/irq_work.h
@@ -6,6 +6,5 @@
 {
 	return true;
 }
-extern void arch_irq_work_raise(void);
 
 #endif /* _ASM_POWERPC_IRQ_WORK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/kprobes.h
@@ -51,7 +51,7 @@
 #define flush_insn_slot(p)	do { } while (0)
 #define kretprobe_blacklist_size 0
 
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 extern void arch_remove_kprobe(struct kprobe *p);
 
 /* Architecture specific copy of original instruction */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/kup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/kup.h
@@ -38,11 +38,6 @@
 static inline void setup_kuep(bool disabled) { }
 #endif /* CONFIG_PPC_KUEP */
 
-#ifndef CONFIG_PPC_BOOK3S_32
-static inline void kuep_lock(void) { }
-static inline void kuep_unlock(void) { }
-#endif
-
 #ifdef CONFIG_PPC_KUAP
 void setup_kuap(bool disabled);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/kvm_book3s_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/kvm_book3s_64.h
@@ -39,7 +39,6 @@
 	pgd_t *shadow_pgtable;		/* our page table for this guest */
 	u64 l1_gr_to_hr;		/* L1's addr of part'n-scoped table */
 	u64 process_table;		/* process table entry for this guest */
-	u64 hfscr;			/* HFSCR that the L1 requested for this nested guest */
 	long refcnt;			/* number of pointers to this struct */
 	struct mutex tlb_lock;		/* serialize page faults and tlbies */
 	struct kvm_nested_guest *next;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/kvm_host.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/kvm_host.h
@@ -814,6 +814,7 @@
 
 	/* For support of nested guests */
 	struct kvm_nested_guest *nested;
+	u64 nested_hfscr;	/* HFSCR that the L1 requested for the nested guest */
 	u32 nested_vcpu_id;
 	gpa_t nested_io_gpr;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/lppaca.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/lppaca.h
@@ -45,6 +45,7 @@
 #include <asm/types.h>
 #include <asm/mmu.h>
 #include <asm/firmware.h>
+#include <asm/paca.h>
 
 /*
  * The lppaca is the "virtual processor area" registered with the hypervisor,
@@ -123,13 +124,23 @@
  */
 #define LPPACA_OLD_SHARED_PROC		2
 
-static inline bool lppaca_shared_proc(struct lppaca *l)
+#ifdef CONFIG_PPC_PSERIES
+/*
+ * All CPUs should have the same shared proc value, so directly access the PACA
+ * to avoid false positives from DEBUG_PREEMPT.
+ */
+static inline bool lppaca_shared_proc(void)
 {
+	struct lppaca *l = local_paca->lppaca_ptr;
+
 	if (!firmware_has_feature(FW_FEATURE_SPLPAR))
 		return false;
 	return !!(l->__old_status & LPPACA_OLD_SHARED_PROC);
 }
 
+#define get_lppaca()	(get_paca()->lppaca_ptr)
+#endif
+
 /*
  * SLB shadow buffer structure as defined in the PAPR.  The save_area
  * contains adjacent ESID and VSID pairs for each shadowed SLB.  The
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/mmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/mmu.h
@@ -416,5 +416,9 @@
 #include <asm/nohash/mmu.h>
 #endif
 
+#if defined(CONFIG_FA_DUMP) || defined(CONFIG_PRESERVE_FA_DUMP)
+#define __HAVE_ARCH_RESERVED_KERNEL_PAGES
+#endif
+
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_MMU_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/mmzone.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/mmzone.h
@@ -42,14 +42,6 @@
 #else
 #define memory_hotplug_max() memblock_end_of_DRAM()
 #endif /* CONFIG_NUMA */
-#ifdef CONFIG_FA_DUMP
-#define __HAVE_ARCH_RESERVED_KERNEL_PAGES
-#endif
-
-#ifdef CONFIG_MEMORY_HOTPLUG
-extern int create_section_mapping(unsigned long start, unsigned long end,
-				  int nid, pgprot_t prot);
-#endif
 
 #endif /* __KERNEL__ */
 #endif /* _ASM_MMZONE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/nohash/32/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/nohash/32/pgtable.h
@@ -64,6 +64,7 @@
 #ifndef __ASSEMBLY__
 
 int map_kernel_page(unsigned long va, phys_addr_t pa, pgprot_t prot);
+void unmap_kernel_page(unsigned long va);
 
 #endif /* !__ASSEMBLY__ */
 
@@ -193,10 +194,12 @@
 }
 #endif
 
+#ifndef pte_mkexec
 static inline pte_t pte_mkexec(pte_t pte)
 {
 	return __pte(pte_val(pte) | _PAGE_EXEC);
 }
+#endif
 
 #define pmd_none(pmd)		(!pmd_val(pmd))
 #define	pmd_bad(pmd)		(pmd_val(pmd) & _PMD_BAD)
@@ -306,30 +309,29 @@
 }
 
 #define __HAVE_ARCH_PTEP_SET_WRPROTECT
+#ifndef ptep_set_wrprotect
 static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr,
 				      pte_t *ptep)
 {
-	unsigned long clr = ~pte_val(pte_wrprotect(__pte(~0)));
-	unsigned long set = pte_val(pte_wrprotect(__pte(0)));
-
-	pte_update(mm, addr, ptep, clr, set, 0);
+	pte_update(mm, addr, ptep, _PAGE_RW, 0, 0);
 }
+#endif
 
+#ifndef __ptep_set_access_flags
 static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
 					   pte_t *ptep, pte_t entry,
 					   unsigned long address,
 					   int psize)
 {
-	pte_t pte_set = pte_mkyoung(pte_mkdirty(pte_mkwrite(pte_mkexec(__pte(0)))));
-	pte_t pte_clr = pte_mkyoung(pte_mkdirty(pte_mkwrite(pte_mkexec(__pte(~0)))));
-	unsigned long set = pte_val(entry) & pte_val(pte_set);
-	unsigned long clr = ~pte_val(entry) & ~pte_val(pte_clr);
+	unsigned long set = pte_val(entry) &
+			    (_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW | _PAGE_EXEC);
 	int huge = psize > mmu_virtual_psize ? 1 : 0;
 
-	pte_update(vma->vm_mm, address, ptep, clr, set, huge);
+	pte_update(vma->vm_mm, address, ptep, 0, set, huge);
 
 	flush_tlb_page(vma, address);
 }
+#endif
 
 static inline int pte_young(pte_t pte)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/nohash/32/pte-40x.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/nohash/32/pte-40x.h
@@ -69,9 +69,6 @@
 
 #define _PTE_NONE_MASK	0
 
-/* Until my rework is finished, 40x still needs atomic PTE updates */
-#define PTE_ATOMIC_UPDATES	1
-
 #define _PAGE_BASE_NC	(_PAGE_PRESENT | _PAGE_ACCESSED)
 #define _PAGE_BASE	(_PAGE_BASE_NC)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/nohash/32/pte-8xx.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/nohash/32/pte-8xx.h
@@ -94,6 +94,13 @@
 
 #define pte_wrprotect pte_wrprotect
 
+static inline int pte_read(pte_t pte)
+{
+	return (pte_val(pte) & _PAGE_RO) != _PAGE_NA;
+}
+
+#define pte_read pte_read
+
 static inline int pte_write(pte_t pte)
 {
 	return !(pte_val(pte) & _PAGE_RO);
@@ -136,6 +143,28 @@
 
 #define pte_mkhuge pte_mkhuge
 
+static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, pte_t *p,
+				     unsigned long clr, unsigned long set, int huge);
+
+static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr, pte_t *ptep)
+{
+	pte_update(mm, addr, ptep, 0, _PAGE_RO, 0);
+}
+#define ptep_set_wrprotect ptep_set_wrprotect
+
+static inline void __ptep_set_access_flags(struct vm_area_struct *vma, pte_t *ptep,
+					   pte_t entry, unsigned long address, int psize)
+{
+	unsigned long set = pte_val(entry) & (_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_EXEC);
+	unsigned long clr = ~pte_val(entry) & _PAGE_RO;
+	int huge = psize > mmu_virtual_psize ? 1 : 0;
+
+	pte_update(vma->vm_mm, address, ptep, clr, set, huge);
+
+	flush_tlb_page(vma, address);
+}
+#define __ptep_set_access_flags __ptep_set_access_flags
+
 static inline unsigned long pgd_leaf_size(pgd_t pgd)
 {
 	if (pgd_val(pgd) & _PMD_PAGE_8M)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/nohash/64/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/nohash/64/pgtable.h
@@ -118,11 +118,6 @@
 	return __pte(pte_val(pte) & ~_PAGE_RW);
 }
 
-static inline pte_t pte_mkexec(pte_t pte)
-{
-	return __pte(pte_val(pte) | _PAGE_EXEC);
-}
-
 #define PMD_BAD_BITS		(PTE_TABLE_SIZE-1)
 #define PUD_BAD_BITS		(PMD_TABLE_SIZE-1)
 
@@ -214,7 +209,7 @@
 {
 	unsigned long old;
 
-	if (pte_young(*ptep))
+	if (!pte_young(*ptep))
 		return 0;
 	old = pte_update(mm, addr, ptep, _PAGE_ACCESSED, 0, 0);
 	return (old & _PAGE_ACCESSED) != 0;
@@ -313,6 +308,7 @@
 #define __swp_entry_to_pte(x)		__pte((x).val)
 
 int map_kernel_page(unsigned long ea, unsigned long pa, pgprot_t prot);
+void unmap_kernel_page(unsigned long va);
 extern int __meminit vmemmap_create_mapping(unsigned long start,
 					    unsigned long page_size,
 					    unsigned long phys);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/nohash/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/nohash/pgtable.h
@@ -45,7 +45,9 @@
 	return pte_val(pte) & _PAGE_RW;
 }
 #endif
+#ifndef pte_read
 static inline int pte_read(pte_t pte)		{ return 1; }
+#endif
 static inline int pte_dirty(pte_t pte)		{ return pte_val(pte) & _PAGE_DIRTY; }
 static inline int pte_special(pte_t pte)	{ return pte_val(pte) & _PAGE_SPECIAL; }
 static inline int pte_none(pte_t pte)		{ return (pte_val(pte) & ~_PTE_NONE_MASK) == 0; }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/nohash/pte-book3e.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/nohash/pte-book3e.h
@@ -48,7 +48,7 @@
 #define _PAGE_WRITETHRU	0x800000 /* W: cache write-through */
 
 /* "Higher level" linux bit combinations */
-#define _PAGE_EXEC		_PAGE_BAP_UX /* .. and was cache cleaned */
+#define _PAGE_EXEC		(_PAGE_BAP_SX | _PAGE_BAP_UX) /* .. and was cache cleaned */
 #define _PAGE_RW		(_PAGE_BAP_SW | _PAGE_BAP_UW) /* User write permission */
 #define _PAGE_KERNEL_RW		(_PAGE_BAP_SW | _PAGE_BAP_SR | _PAGE_DIRTY)
 #define _PAGE_KERNEL_RO		(_PAGE_BAP_SR)
@@ -93,11 +93,11 @@
 /* Permission masks used to generate the __P and __S table */
 #define PAGE_NONE	__pgprot(_PAGE_BASE)
 #define PAGE_SHARED	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW)
-#define PAGE_SHARED_X	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW | _PAGE_EXEC)
+#define PAGE_SHARED_X	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW | _PAGE_BAP_UX)
 #define PAGE_COPY	__pgprot(_PAGE_BASE | _PAGE_USER)
-#define PAGE_COPY_X	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC)
+#define PAGE_COPY_X	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_BAP_UX)
 #define PAGE_READONLY	__pgprot(_PAGE_BASE | _PAGE_USER)
-#define PAGE_READONLY_X	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC)
+#define PAGE_READONLY_X	__pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_BAP_UX)
 
 #ifndef __ASSEMBLY__
 static inline pte_t pte_mkprivileged(pte_t pte)
@@ -113,6 +113,16 @@
 }
 
 #define pte_mkuser pte_mkuser
+
+static inline pte_t pte_mkexec(pte_t pte)
+{
+	if (pte_val(pte) & _PAGE_BAP_UR)
+		return __pte((pte_val(pte) & ~_PAGE_BAP_SX) | _PAGE_BAP_UX);
+	else
+		return __pte((pte_val(pte) & ~_PAGE_BAP_UX) | _PAGE_BAP_SX);
+}
+#define pte_mkexec pte_mkexec
+
 #endif /* __ASSEMBLY__ */
 
 #endif /* __KERNEL__ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/paca.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/paca.h
@@ -14,7 +14,6 @@
 
 #include <linux/string.h>
 #include <asm/types.h>
-#include <asm/lppaca.h>
 #include <asm/mmu.h>
 #include <asm/page.h>
 #ifdef CONFIG_PPC_BOOK3E
@@ -46,14 +45,11 @@
 #define get_paca()	local_paca
 #endif
 
-#ifdef CONFIG_PPC_PSERIES
-#define get_lppaca()	(get_paca()->lppaca_ptr)
-#endif
-
 #define get_slb_shadow()	(get_paca()->slb_shadow_ptr)
 
 struct task_struct;
 struct rtas_args;
+struct lppaca;
 
 /*
  * Defines the layout of the paca.
@@ -263,7 +259,6 @@
 	u64 l1d_flush_size;
 #endif
 #ifdef CONFIG_PPC_PSERIES
-	struct rtas_args *rtas_args_reentrant;
 	u8 *mce_data_buf;		/* buffer to hold per cpu rtas errlog */
 #endif /* CONFIG_PPC_PSERIES */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/page.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/page.h
@@ -132,7 +132,11 @@
 #define virt_to_page(kaddr)	pfn_to_page(virt_to_pfn(kaddr))
 #define pfn_to_kaddr(pfn)	__va((pfn) << PAGE_SHIFT)
 
-#define virt_addr_valid(kaddr)	pfn_valid(virt_to_pfn(kaddr))
+#define virt_addr_valid(vaddr)	({					\
+	unsigned long _addr = (unsigned long)vaddr;			\
+	_addr >= PAGE_OFFSET && _addr < (unsigned long)high_memory &&	\
+	pfn_valid(virt_to_pfn(_addr));					\
+})
 
 /*
  * On Book-E parts we need __va to parse the device tree and we can't
@@ -212,6 +216,9 @@
 #define __pa(x) ((phys_addr_t)(unsigned long)(x) - VIRT_PHYS_OFFSET)
 #else
 #ifdef CONFIG_PPC64
+
+#define VIRTUAL_WARN_ON(x)	WARN_ON(IS_ENABLED(CONFIG_DEBUG_VIRTUAL) && (x))
+
 /*
  * gcc miscompiles (unsigned long)(&static_var) - PAGE_OFFSET
  * with -mcmodel=medium, so we use & and | instead of - and + on 64-bit.
@@ -219,13 +226,13 @@
  */
 #define __va(x)								\
 ({									\
-	VIRTUAL_BUG_ON((unsigned long)(x) >= PAGE_OFFSET);		\
+	VIRTUAL_WARN_ON((unsigned long)(x) >= PAGE_OFFSET);		\
 	(void *)(unsigned long)((phys_addr_t)(x) | PAGE_OFFSET);	\
 })
 
 #define __pa(x)								\
 ({									\
-	VIRTUAL_BUG_ON((unsigned long)(x) < PAGE_OFFSET);		\
+	VIRTUAL_WARN_ON((unsigned long)(x) < PAGE_OFFSET);		\
 	(unsigned long)(x) & 0x0fffffffffffffffUL;			\
 })
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/paravirt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/paravirt.h
@@ -6,6 +6,7 @@
 #include <asm/smp.h>
 #ifdef CONFIG_PPC64
 #include <asm/paca.h>
+#include <asm/lppaca.h>
 #include <asm/hvcall.h>
 #endif
 
@@ -97,7 +98,23 @@
 
 #ifdef CONFIG_PPC_SPLPAR
 	if (!is_kvm_guest()) {
-		int first_cpu = cpu_first_thread_sibling(smp_processor_id());
+		int first_cpu;
+
+		/*
+		 * The result of vcpu_is_preempted() is used in a
+		 * speculative way, and is always subject to invalidation
+		 * by events internal and external to Linux. While we can
+		 * be called in preemptable context (in the Linux sense),
+		 * we're not accessing per-cpu resources in a way that can
+		 * race destructively with Linux scheduler preemption and
+		 * migration, and callers can tolerate the potential for
+		 * error introduced by sampling the CPU index without
+		 * pinning the task to it. So it is permissible to use
+		 * raw_smp_processor_id() here to defeat the preempt debug
+		 * warnings that can arise from using smp_processor_id()
+		 * in arbitrary contexts.
+		 */
+		first_cpu = cpu_first_thread_sibling(raw_smp_processor_id());
 
 		/*
 		 * Preemption can only happen at core granularity. This CPU
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/percpu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/percpu.h
@@ -15,6 +15,16 @@
 #endif /* CONFIG_SMP */
 #endif /* __powerpc64__ */
 
+#if defined(CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK) && defined(CONFIG_SMP)
+#include <linux/jump_label.h>
+DECLARE_STATIC_KEY_FALSE(__percpu_first_chunk_is_paged);
+
+#define percpu_first_chunk_is_paged	\
+		(static_key_enabled(&__percpu_first_chunk_is_paged.key))
+#else
+#define percpu_first_chunk_is_paged	false
+#endif /* CONFIG_PPC64 && CONFIG_SMP */
+
 #include <asm-generic/percpu.h>
 
 #include <asm/paca.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/plpar_wrappers.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/plpar_wrappers.h
@@ -9,6 +9,7 @@
 
 #include <asm/hvcall.h>
 #include <asm/paca.h>
+#include <asm/lppaca.h>
 #include <asm/page.h>
 
 static inline long poll_pending(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/ppc-opcode.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/ppc-opcode.h
@@ -249,6 +249,7 @@
 #define PPC_INST_COPY			0x7c20060c
 #define PPC_INST_DCBA			0x7c0005ec
 #define PPC_INST_DCBA_MASK		0xfc0007fe
+#define PPC_INST_DSSALL			0x7e00066c
 #define PPC_INST_ISEL			0x7c00001e
 #define PPC_INST_ISEL_MASK		0xfc00003e
 #define PPC_INST_LSWI			0x7c0004aa
@@ -498,6 +499,7 @@
 #define PPC_RAW_LDX(r, base, b)		(0x7c00002a | ___PPC_RT(r) | ___PPC_RA(base) | ___PPC_RB(b))
 #define PPC_RAW_LHZ(r, base, i)		(0xa0000000 | ___PPC_RT(r) | ___PPC_RA(base) | IMM_L(i))
 #define PPC_RAW_LHBRX(r, base, b)	(0x7c00062c | ___PPC_RT(r) | ___PPC_RA(base) | ___PPC_RB(b))
+#define PPC_RAW_LWBRX(r, base, b)	(0x7c00042c | ___PPC_RT(r) | ___PPC_RA(base) | ___PPC_RB(b))
 #define PPC_RAW_LDBRX(r, base, b)	(0x7c000428 | ___PPC_RT(r) | ___PPC_RA(base) | ___PPC_RB(b))
 #define PPC_RAW_STWCX(s, a, b)		(0x7c00012d | ___PPC_RS(s) | ___PPC_RA(a) | ___PPC_RB(b))
 #define PPC_RAW_CMPWI(a, i)		(0x2c000000 | ___PPC_RA(a) | IMM_L(i))
@@ -575,6 +577,7 @@
 #define	PPC_DCBZL(a, b)		stringify_in_c(.long PPC_RAW_DCBZL(a, b))
 #define	PPC_DIVDE(t, a, b)	stringify_in_c(.long PPC_RAW_DIVDE(t, a, b))
 #define	PPC_DIVDEU(t, a, b)	stringify_in_c(.long PPC_RAW_DIVDEU(t, a, b))
+#define PPC_DSSALL		stringify_in_c(.long PPC_INST_DSSALL)
 #define PPC_LQARX(t, a, b, eh)	stringify_in_c(.long PPC_RAW_LQARX(t, a, b, eh))
 #define PPC_STQCX(t, a, b)	stringify_in_c(.long PPC_RAW_STQCX(t, a, b))
 #define PPC_MADDHD(t, a, b, c)	stringify_in_c(.long PPC_RAW_MADDHD(t, a, b, c))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/ppc_asm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/ppc_asm.h
@@ -17,29 +17,40 @@
 #define SZL			(BITS_PER_LONG/8)
 
 /*
+ * This expands to a sequence of operations with reg incrementing from
+ * start to end inclusive, of this form:
+ *
+ *   op  reg, (offset + (width * reg))(base)
+ *
+ * Note that offset is not the offset of the first operation unless start
+ * is zero (or width is zero).
+ */
+.macro OP_REGS op, width, start, end, base, offset
+	.Lreg=\start
+	.rept (\end - \start + 1)
+	\op	.Lreg, \offset + \width * .Lreg(\base)
+	.Lreg=.Lreg+1
+	.endr
+.endm
+
+/*
  * Macros for storing registers into and loading registers from
  * exception frames.
  */
 #ifdef __powerpc64__
-#define SAVE_GPR(n, base)	std	n,GPR0+8*(n)(base)
-#define REST_GPR(n, base)	ld	n,GPR0+8*(n)(base)
-#define SAVE_NVGPRS(base)	SAVE_8GPRS(14, base); SAVE_10GPRS(22, base)
-#define REST_NVGPRS(base)	REST_8GPRS(14, base); REST_10GPRS(22, base)
+#define SAVE_GPRS(start, end, base)	OP_REGS std, 8, start, end, base, GPR0
+#define REST_GPRS(start, end, base)	OP_REGS ld, 8, start, end, base, GPR0
+#define SAVE_NVGPRS(base)		SAVE_GPRS(14, 31, base)
+#define REST_NVGPRS(base)		REST_GPRS(14, 31, base)
 #else
-#define SAVE_GPR(n, base)	stw	n,GPR0+4*(n)(base)
-#define REST_GPR(n, base)	lwz	n,GPR0+4*(n)(base)
-#define SAVE_NVGPRS(base)	stmw	13, GPR0+4*13(base)
-#define REST_NVGPRS(base)	lmw	13, GPR0+4*13(base)
+#define SAVE_GPRS(start, end, base)	OP_REGS stw, 4, start, end, base, GPR0
+#define REST_GPRS(start, end, base)	OP_REGS lwz, 4, start, end, base, GPR0
+#define SAVE_NVGPRS(base)		SAVE_GPRS(13, 31, base)
+#define REST_NVGPRS(base)		REST_GPRS(13, 31, base)
 #endif
 
-#define SAVE_2GPRS(n, base)	SAVE_GPR(n, base); SAVE_GPR(n+1, base)
-#define SAVE_4GPRS(n, base)	SAVE_2GPRS(n, base); SAVE_2GPRS(n+2, base)
-#define SAVE_8GPRS(n, base)	SAVE_4GPRS(n, base); SAVE_4GPRS(n+4, base)
-#define SAVE_10GPRS(n, base)	SAVE_8GPRS(n, base); SAVE_2GPRS(n+8, base)
-#define REST_2GPRS(n, base)	REST_GPR(n, base); REST_GPR(n+1, base)
-#define REST_4GPRS(n, base)	REST_2GPRS(n, base); REST_2GPRS(n+2, base)
-#define REST_8GPRS(n, base)	REST_4GPRS(n, base); REST_4GPRS(n+4, base)
-#define REST_10GPRS(n, base)	REST_8GPRS(n, base); REST_2GPRS(n+8, base)
+#define SAVE_GPR(n, base)		SAVE_GPRS(n, n, base)
+#define REST_GPR(n, base)		REST_GPRS(n, n, base)
 
 #define SAVE_FPR(n, base)	stfd	n,8*TS_FPRWIDTH*(n)(base)
 #define SAVE_2FPRS(n, base)	SAVE_FPR(n, base); SAVE_FPR(n+1, base)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/reg_fsl_emb.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/reg_fsl_emb.h
@@ -12,9 +12,16 @@
 #ifndef __ASSEMBLY__
 /* Performance Monitor Registers */
 #define mfpmr(rn)	({unsigned int rval; \
-			asm volatile("mfpmr %0," __stringify(rn) \
+			asm volatile(".machine push; " \
+				     ".machine e300; " \
+				     "mfpmr %0," __stringify(rn) ";" \
+				     ".machine pop; " \
 				     : "=r" (rval)); rval;})
-#define mtpmr(rn, v)	asm volatile("mtpmr " __stringify(rn) ",%0" : : "r" (v))
+#define mtpmr(rn, v)	asm volatile(".machine push; " \
+				     ".machine e300; " \
+				     "mtpmr " __stringify(rn) ",%0; " \
+				     ".machine pop; " \
+				     : : "r" (v))
 #endif /* __ASSEMBLY__ */
 
 /* Freescale Book E Performance Monitor APU Registers */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/rtas.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/rtas.h
@@ -240,7 +240,6 @@
 extern int rtas_token(const char *service);
 extern int rtas_service_present(const char *service);
 extern int rtas_call(int token, int, int, int *, ...);
-int rtas_call_reentrant(int token, int nargs, int nret, int *outputs, ...);
 void rtas_call_unlocked(struct rtas_args *args, int token, int nargs,
 			int nret, ...);
 extern void __noreturn rtas_restart(char *cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/sections.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/sections.h
@@ -6,22 +6,10 @@
 #include <linux/elf.h>
 #include <linux/uaccess.h>
 
-#define arch_is_kernel_initmem_freed arch_is_kernel_initmem_freed
-
 #include <asm-generic/sections.h>
 
-extern bool init_mem_is_free;
-
-static inline int arch_is_kernel_initmem_freed(unsigned long addr)
-{
-	if (!init_mem_is_free)
-		return 0;
-
-	return addr >= (unsigned long)__init_begin &&
-		addr < (unsigned long)__init_end;
-}
-
 extern char __head_end[];
+extern char __srwx_boundary[];
 
 #ifdef __powerpc64__
 
@@ -38,16 +26,16 @@
 extern char end_virt_trampolines[];
 #endif
 
+/*
+ * This assumes the kernel is never compiled -mcmodel=small or
+ * the total .toc is always less than 64k.
+ */
 static inline unsigned long kernel_toc_addr(void)
 {
-	/* Defined by the linker, see vmlinux.lds.S */
-	extern unsigned long __toc_start;
+	unsigned long toc_ptr;
 
-	/*
-	 * The TOC register (r2) points 32kB into the TOC, so that 64kB of
-	 * the TOC can be addressed using a single machine instruction.
-	 */
-	return (unsigned long)(&__toc_start) + 0x8000UL;
+	asm volatile("mr %0, 2" : "=r" (toc_ptr));
+	return toc_ptr;
 }
 
 static inline int overlaps_interrupt_vector_text(unsigned long start,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/set_memory.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/set_memory.h
@@ -6,6 +6,8 @@
 #define SET_MEMORY_RW	1
 #define SET_MEMORY_NX	2
 #define SET_MEMORY_X	3
+#define SET_MEMORY_NP	4	/* Set memory non present */
+#define SET_MEMORY_P	5	/* Set memory present */
 
 int change_memory_attr(unsigned long addr, int numpages, long action);
 
@@ -29,6 +31,14 @@
 	return change_memory_attr(addr, numpages, SET_MEMORY_X);
 }
 
-int set_memory_attr(unsigned long addr, int numpages, pgprot_t prot);
+static inline int set_memory_np(unsigned long addr, int numpages)
+{
+	return change_memory_attr(addr, numpages, SET_MEMORY_NP);
+}
+
+static inline int set_memory_p(unsigned long addr, int numpages)
+{
+	return change_memory_attr(addr, numpages, SET_MEMORY_P);
+}
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/simple_spinlock.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/simple_spinlock.h
@@ -48,10 +48,11 @@
 static inline unsigned long __arch_spin_trylock(arch_spinlock_t *lock)
 {
 	unsigned long tmp, token;
+	unsigned int eh = IS_ENABLED(CONFIG_PPC64);
 
 	token = LOCK_TOKEN;
 	__asm__ __volatile__(
-"1:	lwarx		%0,0,%2,1\n\
+"1:	lwarx		%0,0,%2,%[eh]\n\
 	cmpwi		0,%0,0\n\
 	bne-		2f\n\
 	stwcx.		%1,0,%2\n\
@@ -59,7 +60,7 @@
 	PPC_ACQUIRE_BARRIER
 "2:"
 	: "=&r" (tmp)
-	: "r" (token), "r" (&lock->slock)
+	: "r" (token), "r" (&lock->slock), [eh] "n" (eh)
 	: "cr0", "memory");
 
 	return tmp;
@@ -177,9 +178,10 @@
 static inline long __arch_read_trylock(arch_rwlock_t *rw)
 {
 	long tmp;
+	unsigned int eh = IS_ENABLED(CONFIG_PPC64);
 
 	__asm__ __volatile__(
-"1:	lwarx		%0,0,%1,1\n"
+"1:	lwarx		%0,0,%1,%[eh]\n"
 	__DO_SIGN_EXTEND
 "	addic.		%0,%0,1\n\
 	ble-		2f\n"
@@ -187,7 +189,7 @@
 	bne-		1b\n"
 	PPC_ACQUIRE_BARRIER
 "2:"	: "=&r" (tmp)
-	: "r" (&rw->lock)
+	: "r" (&rw->lock), [eh] "n" (eh)
 	: "cr0", "xer", "memory");
 
 	return tmp;
@@ -200,17 +202,18 @@
 static inline long __arch_write_trylock(arch_rwlock_t *rw)
 {
 	long tmp, token;
+	unsigned int eh = IS_ENABLED(CONFIG_PPC64);
 
 	token = WRLOCK_TOKEN;
 	__asm__ __volatile__(
-"1:	lwarx		%0,0,%2,1\n\
+"1:	lwarx		%0,0,%2,%[eh]\n\
 	cmpwi		0,%0,0\n\
 	bne-		2f\n"
 "	stwcx.		%1,0,%2\n\
 	bne-		1b\n"
 	PPC_ACQUIRE_BARRIER
 "2:"	: "=&r" (tmp)
-	: "r" (token), "r" (&rw->lock)
+	: "r" (token), "r" (&rw->lock), [eh] "n" (eh)
 	: "cr0", "memory");
 
 	return tmp;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/sstep.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/sstep.h
@@ -173,9 +173,4 @@
  */
 extern int emulate_loadstore(struct pt_regs *regs, struct instruction_op *op);
 
-extern void emulate_vsx_load(struct instruction_op *op, union vsx_reg *reg,
-			     const void *mem, bool cross_endian);
-extern void emulate_vsx_store(struct instruction_op *op,
-			      const union vsx_reg *reg, void *mem,
-			      bool cross_endian);
 extern int emulate_dcbz(unsigned long ea, struct pt_regs *regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/syscall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/syscall.h
@@ -90,7 +90,7 @@
 	unsigned long val, mask = -1UL;
 	unsigned int n = 6;
 
-	if (is_32bit_task())
+	if (is_tsk_32bit_task(task))
 		mask = 0xffffffff;
 
 	while (n--) {
@@ -115,7 +115,7 @@
 
 static inline int syscall_get_arch(struct task_struct *task)
 {
-	if (is_32bit_task())
+	if (is_tsk_32bit_task(task))
 		return AUDIT_ARCH_PPC;
 	else if (IS_ENABLED(CONFIG_CPU_LITTLE_ENDIAN))
 		return AUDIT_ARCH_PPC64LE;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/syscalls.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/syscalls.h
@@ -8,6 +8,18 @@
 #include <linux/types.h>
 #include <linux/compat.h>
 
+/*
+ * long long munging:
+ * The 32 bit ABI passes long longs in an odd even register pair.
+ * High and low parts are swapped depending on endian mode,
+ * so define a macro (similar to mips linux32) to handle that.
+ */
+#ifdef __LITTLE_ENDIAN__
+#define merge_64(low, high) (((u64)high << 32) | low)
+#else
+#define merge_64(high, low) (((u64)high << 32) | low)
+#endif
+
 struct rtas_args;
 
 asmlinkage long sys_mmap(unsigned long addr, size_t len,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/thread_info.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/thread_info.h
@@ -14,10 +14,16 @@
 
 #ifdef __KERNEL__
 
-#if defined(CONFIG_VMAP_STACK) && CONFIG_THREAD_SHIFT < PAGE_SHIFT
+#ifdef CONFIG_KASAN
+#define MIN_THREAD_SHIFT	(CONFIG_THREAD_SHIFT + 1)
+#else
+#define MIN_THREAD_SHIFT	CONFIG_THREAD_SHIFT
+#endif
+
+#if defined(CONFIG_VMAP_STACK) && MIN_THREAD_SHIFT < PAGE_SHIFT
 #define THREAD_SHIFT		PAGE_SHIFT
 #else
-#define THREAD_SHIFT		CONFIG_THREAD_SHIFT
+#define THREAD_SHIFT		MIN_THREAD_SHIFT
 #endif
 
 #define THREAD_SIZE		(1 << THREAD_SHIFT)
@@ -165,8 +171,10 @@
 
 #ifdef CONFIG_COMPAT
 #define is_32bit_task()	(test_thread_flag(TIF_32BIT))
+#define is_tsk_32bit_task(tsk)	(test_tsk_thread_flag(tsk, TIF_32BIT))
 #else
 #define is_32bit_task()	(IS_ENABLED(CONFIG_PPC32))
+#define is_tsk_32bit_task(tsk)	(IS_ENABLED(CONFIG_PPC32))
 #endif
 
 #if defined(CONFIG_PPC64)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/timex.h
@@ -19,6 +19,7 @@
 {
 	return mftb();
 }
+#define get_cycles get_cycles
 
 #endif	/* __KERNEL__ */
 #endif	/* _ASM_POWERPC_TIMEX_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/uaccess.h
@@ -90,9 +90,20 @@
 		:						\
 		: label)
 
+#ifdef CONFIG_CC_IS_CLANG
+#define DS_FORM_CONSTRAINT "Z<>"
+#else
+#define DS_FORM_CONSTRAINT "YZ<>"
+#endif
+
 #ifdef __powerpc64__
-#define __put_user_asm2_goto(x, ptr, label)			\
-	__put_user_asm_goto(x, ptr, label, "std")
+#define __put_user_asm2_goto(x, addr, label)			\
+	asm goto ("1: std%U1%X1 %0,%1	# put_user\n"		\
+		EX_TABLE(1b, %l2)				\
+		:						\
+		: "r" (x), DS_FORM_CONSTRAINT (*addr)		\
+		:						\
+		: label)
 #else /* __powerpc64__ */
 #define __put_user_asm2_goto(x, addr, label)			\
 	asm_volatile_goto(					\
@@ -125,8 +136,11 @@
  */
 #define __get_user_atomic_128_aligned(kaddr, uaddr, err)		\
 	__asm__ __volatile__(				\
+		".machine push\n"			\
+		".machine altivec\n"			\
 		"1:	lvx  0,0,%1	# get user\n"	\
 		" 	stvx 0,0,%2	# put kernel\n"	\
+		".machine pop\n"			\
 		"2:\n"					\
 		".section .fixup,\"ax\"\n"		\
 		"3:	li %0,%3\n"			\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/vas.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/vas.h
@@ -112,7 +112,7 @@
  * Receive window attributes specified by the (in-kernel) owner of window.
  */
 struct vas_rx_win_attr {
-	void *rx_fifo;
+	u64 rx_fifo;
 	int rx_fifo_size;
 	int wcreds_max;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/vdso.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/vdso.h
@@ -28,6 +28,7 @@
 #ifdef __VDSO64__
 #define V_FUNCTION_BEGIN(name)		\
 	.globl name;			\
+	.type name,@function; 		\
 	name:				\
 
 #define V_FUNCTION_END(name)		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/vmalloc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/vmalloc.h
@@ -7,14 +7,14 @@
 #ifdef CONFIG_HAVE_ARCH_HUGE_VMAP
 
 #define arch_vmap_pud_supported arch_vmap_pud_supported
-static inline bool arch_vmap_pud_supported(pgprot_t prot)
+static __always_inline bool arch_vmap_pud_supported(pgprot_t prot)
 {
 	/* HPT does not cope with large pages in the vmalloc area */
 	return radix_enabled();
 }
 
 #define arch_vmap_pmd_supported arch_vmap_pmd_supported
-static inline bool arch_vmap_pmd_supported(pgprot_t prot)
+static __always_inline bool arch_vmap_pmd_supported(pgprot_t prot)
 {
 	return radix_enabled();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/include/asm/word-at-a-time.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/include/asm/word-at-a-time.h
@@ -34,7 +34,7 @@
 	return leading_zero_bits >> 3;
 }
 
-static inline bool has_zero(unsigned long val, unsigned long *data, const struct word_at_a_time *c)
+static inline unsigned long has_zero(unsigned long val, unsigned long *data, const struct word_at_a_time *c)
 {
 	unsigned long rhs = val | c->low_bits;
 	*data = rhs;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/Makefile
@@ -11,6 +11,7 @@
 CFLAGS_btext.o		+= -fPIC
 endif
 
+CFLAGS_early_32.o += $(DISABLE_LATENT_ENTROPY_PLUGIN)
 CFLAGS_cputable.o += $(DISABLE_LATENT_ENTROPY_PLUGIN)
 CFLAGS_prom_init.o += $(DISABLE_LATENT_ENTROPY_PLUGIN)
 CFLAGS_btext.o += $(DISABLE_LATENT_ENTROPY_PLUGIN)
@@ -19,6 +20,7 @@
 CFLAGS_prom_init.o += -fno-stack-protector
 CFLAGS_prom_init.o += -DDISABLE_BRANCH_PROFILING
 CFLAGS_prom_init.o += -ffreestanding
+CFLAGS_prom_init.o += $(call cc-option, -ftrivial-auto-var-init=uninitialized)
 
 ifdef CONFIG_FUNCTION_TRACER
 # Do not trace early boot code
@@ -196,3 +198,6 @@
 # Force dependency (incbin is bad)
 $(obj)/vdso32_wrapper.o : $(obj)/vdso32/vdso32.so.dbg
 $(obj)/vdso64_wrapper.o : $(obj)/vdso64/vdso64.so.dbg
+
+# for cleaning
+subdir- += vdso32 vdso64
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/btext.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/btext.c
@@ -241,8 +241,10 @@
 			rc = btext_initialize(np);
 			printk("result: %d\n", rc);
 		}
-		if (rc == 0)
+		if (rc == 0) {
+			of_node_put(np);
 			break;
+		}
 	}
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/cputable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/cputable.c
@@ -2119,7 +2119,7 @@
 struct static_key_true mmu_feature_keys[NUM_MMU_FTR_KEYS] = {
 			[0 ... NUM_MMU_FTR_KEYS - 1] = STATIC_KEY_TRUE_INIT
 };
-EXPORT_SYMBOL_GPL(mmu_feature_keys);
+EXPORT_SYMBOL(mmu_feature_keys);
 
 void __init mmu_feature_keys_init(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/dma-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/dma-iommu.c
@@ -144,7 +144,7 @@
 /* We support DMA to/from any memory page via the iommu */
 int dma_iommu_dma_supported(struct device *dev, u64 mask)
 {
-	struct iommu_table *tbl = get_iommu_table_base(dev);
+	struct iommu_table *tbl;
 
 	if (dev_is_pci(dev) && dma_iommu_bypass_supported(dev, mask)) {
 		/*
@@ -162,6 +162,8 @@
 		return 1;
 	}
 
+	tbl = get_iommu_table_base(dev);
+
 	if (!tbl) {
 		dev_err(dev, "Warning: IOMMU dma not supported: mask 0x%08llx, table unavailable\n", mask);
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/eeh_driver.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/eeh_driver.c
@@ -1054,45 +1054,46 @@
 		}
 
 		pr_info("EEH: Recovery successful.\n");
-	} else  {
-		/*
-		 * About 90% of all real-life EEH failures in the field
-		 * are due to poorly seated PCI cards. Only 10% or so are
-		 * due to actual, failed cards.
-		 */
-		pr_err("EEH: Unable to recover from failure from PHB#%x-PE#%x.\n"
-		       "Please try reseating or replacing it\n",
-			pe->phb->global_number, pe->addr);
-
-		eeh_slot_error_detail(pe, EEH_LOG_PERM);
-
-		/* Notify all devices that they're about to go down. */
-		eeh_set_channel_state(pe, pci_channel_io_perm_failure);
-		eeh_set_irq_state(pe, false);
-		eeh_pe_report("error_detected(permanent failure)", pe,
-			      eeh_report_failure, NULL);
+		goto out;
+	}
 
-		/* Mark the PE to be removed permanently */
-		eeh_pe_state_mark(pe, EEH_PE_REMOVED);
+	/*
+	 * About 90% of all real-life EEH failures in the field
+	 * are due to poorly seated PCI cards. Only 10% or so are
+	 * due to actual, failed cards.
+	 */
+	pr_err("EEH: Unable to recover from failure from PHB#%x-PE#%x.\n"
+		"Please try reseating or replacing it\n",
+		pe->phb->global_number, pe->addr);
+
+	eeh_slot_error_detail(pe, EEH_LOG_PERM);
+
+	/* Notify all devices that they're about to go down. */
+	eeh_set_irq_state(pe, false);
+	eeh_pe_report("error_detected(permanent failure)", pe,
+		      eeh_report_failure, NULL);
+	eeh_set_channel_state(pe, pci_channel_io_perm_failure);
 
-		/*
-		 * Shut down the device drivers for good. We mark
-		 * all removed devices correctly to avoid access
-		 * the their PCI config any more.
-		 */
-		if (pe->type & EEH_PE_VF) {
-			eeh_pe_dev_traverse(pe, eeh_rmv_device, NULL);
-			eeh_pe_dev_mode_mark(pe, EEH_DEV_REMOVED);
-		} else {
-			eeh_pe_state_clear(pe, EEH_PE_PRI_BUS, true);
-			eeh_pe_dev_mode_mark(pe, EEH_DEV_REMOVED);
+	/* Mark the PE to be removed permanently */
+	eeh_pe_state_mark(pe, EEH_PE_REMOVED);
 
-			pci_lock_rescan_remove();
-			pci_hp_remove_devices(bus);
-			pci_unlock_rescan_remove();
-			/* The passed PE should no longer be used */
-			return;
-		}
+	/*
+	 * Shut down the device drivers for good. We mark
+	 * all removed devices correctly to avoid access
+	 * the their PCI config any more.
+	 */
+	if (pe->type & EEH_PE_VF) {
+		eeh_pe_dev_traverse(pe, eeh_rmv_device, NULL);
+		eeh_pe_dev_mode_mark(pe, EEH_DEV_REMOVED);
+	} else {
+		eeh_pe_state_clear(pe, EEH_PE_PRI_BUS, true);
+		eeh_pe_dev_mode_mark(pe, EEH_DEV_REMOVED);
+
+		pci_lock_rescan_remove();
+		pci_hp_remove_devices(bus);
+		pci_unlock_rescan_remove();
+		/* The passed PE should no longer be used */
+		return;
 	}
 
 out:
@@ -1188,10 +1189,10 @@
 
 			/* Notify all devices to be down */
 			eeh_pe_state_clear(pe, EEH_PE_PRI_BUS, true);
-			eeh_set_channel_state(pe, pci_channel_io_perm_failure);
 			eeh_pe_report(
 				"error_detected(permanent failure)", pe,
 				eeh_report_failure, NULL);
+			eeh_set_channel_state(pe, pci_channel_io_perm_failure);
 
 			pci_lock_rescan_remove();
 			list_for_each_entry(hose, &hose_list, list_node) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/eeh_pe.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/eeh_pe.c
@@ -849,6 +849,7 @@
 {
 	struct eeh_dev *edev;
 	struct pci_dev *pdev;
+	struct pci_bus *bus = NULL;
 
 	if (pe->type & EEH_PE_PHB)
 		return pe->phb->bus;
@@ -859,9 +860,11 @@
 
 	/* Retrieve the parent PCI bus of first (top) PCI device */
 	edev = list_first_entry_or_null(&pe->edevs, struct eeh_dev, entry);
+	pci_lock_rescan_remove();
 	pdev = eeh_dev_to_pci_dev(edev);
 	if (pdev)
-		return pdev->bus;
+		bus = pdev->bus;
+	pci_unlock_rescan_remove();
 
-	return NULL;
+	return bus;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/entry_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/entry_32.S
@@ -73,6 +73,34 @@
 _ASM_NOKPROBE_SYMBOL(prepare_transfer_to_handler)
 #endif /* CONFIG_PPC_BOOK3S_32 || CONFIG_E500 */
 
+#if defined(CONFIG_PPC_KUEP) && defined(CONFIG_PPC_BOOK3S_32)
+	.globl	__kuep_lock
+__kuep_lock:
+	mfsr    r9,0
+	rlwinm  r9,r9,0,8,3
+	oris    r9,r9,SR_NX@h
+	update_user_segments_by_4 r9, r10, r11, r12
+	blr
+
+__kuep_unlock:
+	mfsr    r9,0
+	rlwinm  r9,r9,0,8,2
+	update_user_segments_by_4 r9, r10, r11, r12
+	blr
+
+.macro	kuep_lock
+	bl	__kuep_lock
+.endm
+.macro	kuep_unlock
+	bl	__kuep_unlock
+.endm
+#else
+.macro	kuep_lock
+.endm
+.macro	kuep_unlock
+.endm
+#endif
+
 	.globl	transfer_to_syscall
 transfer_to_syscall:
 	stw	r11, GPR1(r1)
@@ -90,10 +118,10 @@
 	stw	r12,8(r1)
 	stw	r2,_TRAP(r1)
 	SAVE_GPR(0, r1)
-	SAVE_4GPRS(3, r1)
-	SAVE_2GPRS(7, r1)
+	SAVE_GPRS(3, 8, r1)
 	addi	r2,r10,-THREAD
 	SAVE_NVGPRS(r1)
+	kuep_lock
 
 	/* Calling convention has r9 = orig r0, r10 = regs */
 	addi	r10,r1,STACK_FRAME_OVERHEAD
@@ -108,8 +136,10 @@
 	lis	r4,icache_44x_need_flush@ha
 	lwz	r5,icache_44x_need_flush@l(r4)
 	cmplwi	cr0,r5,0
-	bne-	2f
+	bne-	.L44x_icache_flush
 #endif /* CONFIG_PPC_47x */
+.L44x_icache_flush_return:
+	kuep_unlock
 	lwz	r4,_LINK(r1)
 	lwz	r5,_CCR(r1)
 	mtlr	r4
@@ -139,15 +169,16 @@
 	mtxer	r5
 	lwz	r0,GPR0(r1)
 	lwz	r3,GPR3(r1)
-	REST_8GPRS(4,r1)
+	REST_GPRS(4, 11, r1)
 	lwz	r12,GPR12(r1)
 	b	1b
 
 #ifdef CONFIG_44x
-2:	li	r7,0
+.L44x_icache_flush:
+	li	r7,0
 	iccci	r0,r0
 	stw	r7,icache_44x_need_flush@l(r4)
-	b	1b
+	b	.L44x_icache_flush_return
 #endif  /* CONFIG_44x */
 
 	.globl	ret_from_fork
@@ -232,9 +263,9 @@
 	beq	3f			/* if not, we've got problems */
 #endif
 
-2:	REST_4GPRS(3, r11)
+2:	REST_GPRS(3, 6, r11)
 	lwz	r10,_CCR(r11)
-	REST_2GPRS(1, r11)
+	REST_GPRS(1, 2, r11)
 	mtcr	r10
 	lwz	r10,_LINK(r11)
 	mtlr	r10
@@ -273,6 +304,7 @@
 	beq	.Lkernel_interrupt_return
 	bl	interrupt_exit_user_prepare
 	cmpwi	r3,0
+	kuep_unlock
 	bne-	.Lrestore_nvgprs
 
 .Lfast_user_interrupt_return:
@@ -298,16 +330,14 @@
 	 * the reliable stack unwinder later on. Clear it.
 	 */
 	stw	r0,8(r1)
-	REST_4GPRS(7, r1)
-	REST_2GPRS(11, r1)
+	REST_GPRS(7, 12, r1)
 
 	mtcr	r3
 	mtlr	r4
 	mtctr	r5
 	mtspr	SPRN_XER,r6
 
-	REST_4GPRS(2, r1)
-	REST_GPR(6, r1)
+	REST_GPRS(2, 6, r1)
 	REST_GPR(0, r1)
 	REST_GPR(1, r1)
 	rfi
@@ -341,8 +371,7 @@
 	lwz	r6,_CCR(r1)
 	li	r0,0
 
-	REST_4GPRS(7, r1)
-	REST_2GPRS(11, r1)
+	REST_GPRS(7, 12, r1)
 
 	mtlr	r3
 	mtctr	r4
@@ -354,7 +383,7 @@
 	 */
 	stw	r0,8(r1)
 
-	REST_4GPRS(2, r1)
+	REST_GPRS(2, 5, r1)
 
 	bne-	cr1,1f /* emulate stack store */
 	mtcr	r6
@@ -430,8 +459,7 @@
 	bne	interrupt_return;					\
 	lwz	r0,GPR0(r1);						\
 	lwz	r2,GPR2(r1);						\
-	REST_4GPRS(3, r1);						\
-	REST_2GPRS(7, r1);						\
+	REST_GPRS(3, 8, r1);						\
 	lwz	r10,_XER(r1);						\
 	lwz	r11,_CTR(r1);						\
 	mtspr	SPRN_XER,r10;						\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/entry_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/entry_64.S
@@ -330,22 +330,22 @@
 	clrldi	r4,r4,2			/* convert to realmode address */
        	mtlr	r4
 
-	li	r0,0
-	ori	r0,r0,MSR_EE|MSR_SE|MSR_BE|MSR_RI
-	andc	r0,r6,r0
-	
-        li      r9,1
-        rldicr  r9,r9,MSR_SF_LG,(63-MSR_SF_LG)
-	ori	r9,r9,MSR_IR|MSR_DR|MSR_FE0|MSR_FE1|MSR_FP|MSR_RI|MSR_LE
-	andc	r6,r0,r9
-
 __enter_rtas:
-	sync				/* disable interrupts so SRR0/1 */
-	mtmsrd	r0			/* don't get trashed */
-
 	LOAD_REG_ADDR(r4, rtas)
 	ld	r5,RTASENTRY(r4)	/* get the rtas->entry value */
 	ld	r4,RTASBASE(r4)		/* get the rtas->base value */
+
+	/*
+	 * RTAS runs in 32-bit big endian real mode, but leave MSR[RI] on as we
+	 * may hit NMI (SRESET or MCE) while in RTAS. RTAS should disable RI in
+	 * its critical regions (as specified in PAPR+ section 7.2.1). MSR[S]
+	 * is not impacted by RFI_TO_KERNEL (only urfid can unset it). So if
+	 * MSR[S] is set, it will remain when entering RTAS.
+	 */
+	LOAD_REG_IMMEDIATE(r6, MSR_ME | MSR_RI)
+
+	li      r0,0
+	mtmsrd  r0,1                    /* disable RI before using SRR0/1 */
 	
 	mtspr	SPRN_SRR0,r5
 	mtspr	SPRN_SRR1,r6
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/exceptions-64e.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/exceptions-64e.S
@@ -198,8 +198,7 @@
 
 	stdcx.	r0,0,r1		/* to clear the reservation */
 
-	REST_4GPRS(2, r1)
-	REST_4GPRS(6, r1)
+	REST_GPRS(2, 9, r1)
 
 	ld	r10,_CTR(r1)
 	ld	r11,_XER(r1)
@@ -375,9 +374,7 @@
 exc_##n##_common:							    \
 	std	r0,GPR0(r1);		/* save r0 in stackframe */	    \
 	std	r2,GPR2(r1);		/* save r2 in stackframe */	    \
-	SAVE_4GPRS(3, r1);		/* save r3 - r6 in stackframe */    \
-	SAVE_2GPRS(7, r1);		/* save r7, r8 in stackframe */	    \
-	std	r9,GPR9(r1);		/* save r9 in stackframe */	    \
+	SAVE_GPRS(3, 9, r1);		/* save r3 - r9 in stackframe */    \
 	std	r10,_NIP(r1);		/* save SRR0 to stackframe */	    \
 	std	r11,_MSR(r1);		/* save SRR1 to stackframe */	    \
 	beq	2f;			/* if from kernel mode */	    \
@@ -1061,9 +1058,7 @@
 	std	r11,_ESR(r1)
 	std	r0,GPR0(r1);		/* save r0 in stackframe */	    \
 	std	r2,GPR2(r1);		/* save r2 in stackframe */	    \
-	SAVE_4GPRS(3, r1);		/* save r3 - r6 in stackframe */    \
-	SAVE_2GPRS(7, r1);		/* save r7, r8 in stackframe */	    \
-	std	r9,GPR9(r1);		/* save r9 in stackframe */	    \
+	SAVE_GPRS(3, 9, r1);		/* save r3 - r9 in stackframe */    \
 	ld	r3,PACA_EXGEN+EX_R10(r13);/* get back r10 */		    \
 	ld	r4,PACA_EXGEN+EX_R11(r13);/* get back r11 */		    \
 	mfspr	r5,SPRN_SPRG_GEN_SCRATCH;/* get back r13 XXX can be wrong */ \
@@ -1077,8 +1072,7 @@
 	std	r10,_LINK(r1)
 	std	r11,_CTR(r1)
 	std	r12,_XER(r1)
-	SAVE_10GPRS(14,r1)
-	SAVE_8GPRS(24,r1)
+	SAVE_GPRS(14, 31, r1)
 	lhz	r12,PACA_TRAP_SAVE(r13)
 	std	r12,_TRAP(r1)
 	addi	r11,r1,INT_FRAME_SIZE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/exceptions-64s.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/exceptions-64s.S
@@ -574,8 +574,7 @@
 	ld	r10,IAREA+EX_CTR(r13)
 	std	r10,_CTR(r1)
 	std	r2,GPR2(r1)		/* save r2 in stackframe	*/
-	SAVE_4GPRS(3, r1)		/* save r3 - r6 in stackframe   */
-	SAVE_2GPRS(7, r1)		/* save r7, r8 in stackframe	*/
+	SAVE_GPRS(3, 8, r1)		/* save r3 - r8 in stackframe   */
 	mflr	r9			/* Get LR, later save to stack	*/
 	ld	r2,PACATOC(r13)		/* get kernel TOC into r2	*/
 	std	r9,_LINK(r1)
@@ -693,8 +692,7 @@
 	mtlr	r9
 	ld	r9,_CCR(r1)
 	mtcr	r9
-	REST_8GPRS(2, r1)
-	REST_4GPRS(10, r1)
+	REST_GPRS(2, 13, r1)
 	REST_GPR(0, r1)
 	/* restore original r1. */
 	ld	r1,GPR1(r1)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/fadump.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/fadump.c
@@ -544,7 +544,7 @@
 		if (!fw_dump.nocma) {
 			fw_dump.boot_memory_size =
 				ALIGN(fw_dump.boot_memory_size,
-				      FADUMP_CMA_ALIGNMENT);
+				      CMA_MIN_ALIGNMENT_BYTES);
 		}
 #endif
 
@@ -642,6 +642,7 @@
 	return ret;
 error_out:
 	fw_dump.fadump_enabled = 0;
+	fw_dump.reserve_dump_area_size = 0;
 	return 0;
 }
 
@@ -861,7 +862,6 @@
 				       sizeof(struct fadump_memory_range));
 	return 0;
 }
-
 static inline int fadump_add_mem_range(struct fadump_mrange_info *mrange_info,
 				       u64 base, u64 end)
 {
@@ -880,7 +880,12 @@
 		start = mem_ranges[mrange_info->mem_range_cnt - 1].base;
 		size  = mem_ranges[mrange_info->mem_range_cnt - 1].size;
 
-		if ((start + size) == base)
+		/*
+		 * Boot memory area needs separate PT_LOAD segment(s) as it
+		 * is moved to a different location at the time of crash.
+		 * So, fold only if the region is not boot memory area.
+		 */
+		if ((start + size) == base && start >= fw_dump.boot_mem_top)
 			is_adjacent = true;
 	}
 	if (!is_adjacent) {
@@ -1641,6 +1646,14 @@
 	else if (fw_dump.reserve_dump_area_size)
 		fw_dump.ops->fadump_init_mem_struct(&fw_dump);
 
+	/*
+	 * In case of panic, fadump is triggered via ppc_panic_event()
+	 * panic notifier. Setting crash_kexec_post_notifiers to 'true'
+	 * lets panic() function take crash friendly path before panic
+	 * notifiers are invoked.
+	 */
+	crash_kexec_post_notifiers = true;
+
 	return 1;
 }
 subsys_initcall(setup_fadump);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/firmware.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/firmware.c
@@ -31,11 +31,10 @@
 	if (!hyper_node)
 		return 0;
 
-	if (!of_device_is_compatible(hyper_node, "linux,kvm"))
-		return 0;
-
-	static_branch_enable(&kvm_guest);
+	if (of_device_is_compatible(hyper_node, "linux,kvm"))
+		static_branch_enable(&kvm_guest);
 
+	of_node_put(hyper_node);
 	return 0;
 }
 core_initcall(check_kvm_guest); // before kvm_guest_init()
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/fpu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/fpu.S
@@ -23,6 +23,15 @@
 #include <asm/feature-fixups.h>
 
 #ifdef CONFIG_VSX
+#define __REST_1FPVSR(n,c,base)						\
+BEGIN_FTR_SECTION							\
+	b	2f;							\
+END_FTR_SECTION_IFSET(CPU_FTR_VSX);					\
+	REST_FPR(n,base);						\
+	b	3f;							\
+2:	REST_VSR(n,c,base);						\
+3:
+
 #define __REST_32FPVSRS(n,c,base)					\
 BEGIN_FTR_SECTION							\
 	b	2f;							\
@@ -41,9 +50,11 @@
 2:	SAVE_32VSRS(n,c,base);						\
 3:
 #else
+#define __REST_1FPVSR(n,b,base)		REST_FPR(n, base)
 #define __REST_32FPVSRS(n,b,base)	REST_32FPRS(n, base)
 #define __SAVE_32FPVSRS(n,b,base)	SAVE_32FPRS(n, base)
 #endif
+#define REST_1FPVSR(n,c,base)   __REST_1FPVSR(n,__REG_##c,__REG_##base)
 #define REST_32FPVSRS(n,c,base) __REST_32FPVSRS(n,__REG_##c,__REG_##base)
 #define SAVE_32FPVSRS(n,c,base) __SAVE_32FPVSRS(n,__REG_##c,__REG_##base)
 
@@ -67,6 +78,7 @@
 	SAVE_32FPVSRS(0, R4, R3)
 	mffs	fr0
 	stfd	fr0,FPSTATE_FPSCR(r3)
+	REST_1FPVSR(0, R4, R3)
 	blr
 EXPORT_SYMBOL(store_fp_state)
 
@@ -133,4 +145,5 @@
 2:	SAVE_32FPVSRS(0, R4, R6)
 	mffs	fr0
 	stfd	fr0,FPSTATE_FPSCR(r6)
+	REST_1FPVSR(0, R4, R6)
 	blr
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_32.h
@@ -115,8 +115,7 @@
 	stw	r10,8(r1)
 	li	r10, \trapno
 	stw	r10,_TRAP(r1)
-	SAVE_4GPRS(3, r1)
-	SAVE_2GPRS(7, r1)
+	SAVE_GPRS(3, 8, r1)
 	SAVE_NVGPRS(r1)
 	stw	r2,GPR2(r1)
 	stw	r12,_NIP(r1)
@@ -136,6 +135,12 @@
 	andi.	r12,r9,MSR_PR
 	bne	777f
 	bl	prepare_transfer_to_handler
+#ifdef CONFIG_PPC_KUEP
+	b	778f
+777:
+	bl	__kuep_lock
+778:
+#endif
 777:
 #endif
 .endm
@@ -202,11 +207,11 @@
 	mfspr	r1, SPRN_SPRG_THREAD
 	lwz	r1, TASK_CPU - THREAD(r1)
 	slwi	r1, r1, 3
-	addis	r1, r1, emergency_ctx@ha
+	addis	r1, r1, emergency_ctx-PAGE_OFFSET@ha
 #else
-	lis	r1, emergency_ctx@ha
+	lis	r1, emergency_ctx-PAGE_OFFSET@ha
 #endif
-	lwz	r1, emergency_ctx@l(r1)
+	lwz	r1, emergency_ctx-PAGE_OFFSET@l(r1)
 	addi	r1, r1, THREAD_SIZE - INT_FRAME_SIZE
 	EXCEPTION_PROLOG_2 0 vmap_stack_overflow
 	prepare_transfer_to_handler
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_40x.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_40x.S
@@ -27,6 +27,7 @@
 
 #include <linux/init.h>
 #include <linux/pgtable.h>
+#include <linux/sizes.h>
 #include <asm/processor.h>
 #include <asm/page.h>
 #include <asm/mmu.h>
@@ -650,7 +651,7 @@
 	b	.		/* prevent prefetch past rfi */
 
 /* Set up the initial MMU state so we can do the first level of
- * kernel initialization.  This maps the first 16 MBytes of memory 1:1
+ * kernel initialization.  This maps the first 32 MBytes of memory 1:1
  * virtual to physical and more importantly sets the cache mode.
  */
 initial_mmu:
@@ -687,6 +688,12 @@
 	tlbwe	r4,r0,TLB_DATA		/* Load the data portion of the entry */
 	tlbwe	r3,r0,TLB_TAG		/* Load the tag portion of the entry */
 
+	li	r0,62			/* TLB slot 62 */
+	addis	r4,r4,SZ_16M@h
+	addis	r3,r3,SZ_16M@h
+	tlbwe	r4,r0,TLB_DATA		/* Load the data portion of the entry */
+	tlbwe	r3,r0,TLB_TAG		/* Load the tag portion of the entry */
+
 	isync
 
 	/* Establish the exception vector base
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_64.S
@@ -904,7 +904,7 @@
 	blr
 
 .balign 8
-p_toc:	.8byte	__toc_start + 0x8000 - 0b
+p_toc:	.8byte	.TOC. - 0b
 
 /*
  * This is where the main kernel code starts.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_8xx.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_8xx.S
@@ -40,12 +40,12 @@
 #include "head_32.h"
 
 .macro compare_to_kernel_boundary scratch, addr
-#if CONFIG_TASK_SIZE <= 0x80000000 && CONFIG_PAGE_OFFSET >= 0x80000000
+#if CONFIG_TASK_SIZE <= 0x80000000 && MODULES_VADDR >= 0x80000000
 /* By simply checking Address >= 0x80000000, we know if its a kernel address */
 	not.	\scratch, \addr
 #else
 	rlwinm	\scratch, \addr, 16, 0xfff8
-	cmpli	cr0, \scratch, PAGE_OFFSET@h
+	cmpli	cr0, \scratch, TASK_SIZE@h
 #endif
 .endm
 
@@ -403,7 +403,7 @@
 	mfspr	r10, SPRN_SRR0
 	mtspr	SPRN_MD_EPN, r10
 	rlwinm	r11, r10, 16, 0xfff8
-	cmpli	cr1, r11, PAGE_OFFSET@h
+	cmpli	cr1, r11, TASK_SIZE@h
 	mfspr	r11, SPRN_M_TWB	/* Get level 1 table */
 	blt+	cr1, 3f
 
@@ -733,6 +733,7 @@
 #ifdef CONFIG_PIN_TLB_DATA
 	LOAD_REG_IMMEDIATE(r6, PAGE_OFFSET)
 	LOAD_REG_IMMEDIATE(r7, MI_SVALID | MI_PS8MEG | _PMD_ACCESSED)
+	li	r8, 0
 #ifdef CONFIG_PIN_TLB_IMMR
 	li	r0, 3
 #else
@@ -741,26 +742,26 @@
 	mtctr	r0
 	cmpwi	r4, 0
 	beq	4f
-	LOAD_REG_IMMEDIATE(r8, 0xf0 | _PAGE_RO | _PAGE_SPS | _PAGE_SH | _PAGE_PRESENT)
 	LOAD_REG_ADDR(r9, _sinittext)
 
 2:	ori	r0, r6, MD_EVALID
+	ori	r12, r8, 0xf0 | _PAGE_RO | _PAGE_SPS | _PAGE_SH | _PAGE_PRESENT
 	mtspr	SPRN_MD_CTR, r5
 	mtspr	SPRN_MD_EPN, r0
 	mtspr	SPRN_MD_TWC, r7
-	mtspr	SPRN_MD_RPN, r8
+	mtspr	SPRN_MD_RPN, r12
 	addi	r5, r5, 0x100
 	addis	r6, r6, SZ_8M@h
 	addis	r8, r8, SZ_8M@h
 	cmplw	r6, r9
 	bdnzt	lt, 2b
-
-4:	LOAD_REG_IMMEDIATE(r8, 0xf0 | _PAGE_SPS | _PAGE_SH | _PAGE_PRESENT)
+4:
 2:	ori	r0, r6, MD_EVALID
+	ori	r12, r8, 0xf0 | _PAGE_DIRTY | _PAGE_SPS | _PAGE_SH | _PAGE_PRESENT
 	mtspr	SPRN_MD_CTR, r5
 	mtspr	SPRN_MD_EPN, r0
 	mtspr	SPRN_MD_TWC, r7
-	mtspr	SPRN_MD_RPN, r8
+	mtspr	SPRN_MD_RPN, r12
 	addi	r5, r5, 0x100
 	addis	r6, r6, SZ_8M@h
 	addis	r8, r8, SZ_8M@h
@@ -781,7 +782,7 @@
 #endif
 #if defined(CONFIG_PIN_TLB_IMMR) || defined(CONFIG_PIN_TLB_DATA)
 	lis	r0, (MD_RSV4I | MD_TWAM)@h
-	mtspr	SPRN_MI_CTR, r0
+	mtspr	SPRN_MD_CTR, r0
 #endif
 	mtspr	SPRN_SRR1, r10
 	mtspr	SPRN_SRR0, r11
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_book3s_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_book3s_32.S
@@ -931,7 +931,11 @@
 _GLOBAL(load_segment_registers)
 	li	r0, NUM_USER_SEGMENTS /* load up user segment register values */
 	mtctr	r0		/* for context 0 */
+#ifdef CONFIG_PPC_KUEP
+	lis	r3, SR_NX@h	/* Kp = 0, Ks = 0, VSID = 0 */
+#else
 	li	r3, 0		/* Kp = 0, Ks = 0, VSID = 0 */
+#endif
 	li	r4, 0
 3:	mtsrin	r3, r4
 	addi	r3, r3, 0x111	/* increment VSID */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_booke.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_booke.h
@@ -87,8 +87,7 @@
 	stw	r10, 8(r1)
 	li	r10, \trapno
 	stw	r10,_TRAP(r1)
-	SAVE_4GPRS(3, r1)
-	SAVE_2GPRS(7, r1)
+	SAVE_GPRS(3, 8, r1)
 	SAVE_NVGPRS(r1)
 	stw	r2,GPR2(r1)
 	stw	r12,_NIP(r1)
@@ -465,12 +464,21 @@
 	bl	do_page_fault;						      \
 	b	interrupt_return
 
+/*
+ * Instruction TLB Error interrupt handlers may call InstructionStorage
+ * directly without clearing ESR, so the ESR at this point may be left over
+ * from a prior interrupt.
+ *
+ * In any case, do_page_fault for BOOK3E does not use ESR and always expects
+ * dsisr to be 0. ESR_DST from a prior store in particular would confuse fault
+ * handling.
+ */
 #define INSTRUCTION_STORAGE_EXCEPTION					      \
 	START_EXCEPTION(InstructionStorage)				      \
-	NORMAL_EXCEPTION_PROLOG(0x400, INST_STORAGE);		      \
-	mfspr	r5,SPRN_ESR;		/* Grab the ESR and save it */	      \
+	NORMAL_EXCEPTION_PROLOG(0x400, INST_STORAGE);			      \
+	li	r5,0;			/* Store 0 in regs->esr (dsisr) */    \
 	stw	r5,_ESR(r11);						      \
-	stw	r12, _DEAR(r11);	/* Pass SRR0 as arg2 */		      \
+	stw	r12, _DEAR(r11);	/* Set regs->dear (dar) to SRR0 */    \
 	prepare_transfer_to_handler;					      \
 	bl	do_page_fault;						      \
 	b	interrupt_return
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/head_fsl_booke.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/head_fsl_booke.S
@@ -394,7 +394,7 @@
 #ifdef CONFIG_PPC_FPU
 	FP_UNAVAILABLE_EXCEPTION
 #else
-	EXCEPTION(0x0800, FP_UNAVAIL, FloatingPointUnavailable, unknown_exception)
+	EXCEPTION(0x0800, FP_UNAVAIL, FloatingPointUnavailable, emulation_assist_interrupt)
 #endif
 
 	/* System Call Interrupt */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/hw_breakpoint.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/hw_breakpoint.c
@@ -478,11 +478,13 @@
 	struct arch_hw_breakpoint *info;
 	int i;
 
+	preempt_disable();
+
 	for (i = 0; i < nr_wp_slots(); i++) {
 		if (unlikely(tsk->thread.last_hit_ubp[i]))
 			goto reset;
 	}
-	return;
+	goto out;
 
 reset:
 	regs_set_return_msr(regs, regs->msr & ~MSR_SE);
@@ -491,6 +493,9 @@
 		__set_breakpoint(i, info);
 		tsk->thread.last_hit_ubp[i] = NULL;
 	}
+
+out:
+	preempt_enable();
 }
 
 static bool is_larx_stcx_instr(int type)
@@ -605,6 +610,11 @@
 	}
 }
 
+/*
+ * Handle a DABR or DAWR exception.
+ *
+ * Called in atomic context.
+ */
 int hw_breakpoint_handler(struct die_args *args)
 {
 	bool err = false;
@@ -731,6 +741,8 @@
 
 /*
  * Handle single-step exceptions following a DABR hit.
+ *
+ * Called in atomic context.
  */
 static int single_step_dabr_instruction(struct die_args *args)
 {
@@ -788,6 +800,8 @@
 
 /*
  * Handle debug exception notifications.
+ *
+ * Called in atomic context.
  */
 int hw_breakpoint_exceptions_notify(
 		struct notifier_block *unused, unsigned long val, void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/hw_breakpoint_constraints.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/hw_breakpoint_constraints.c
@@ -140,8 +140,13 @@
 			 int *type, int *size, unsigned long *ea)
 {
 	struct instruction_op op;
+	int err;
 
-	if (__get_user_instr(*instr, (void __user *)regs->nip))
+	pagefault_disable();
+	err = __get_user_instr(*instr, (void __user *)regs->nip);
+	pagefault_enable();
+
+	if (err)
 		return;
 
 	analyse_instr(&op, regs, *instr);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/idle.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/idle.c
@@ -37,7 +37,7 @@
 {
 	ppc_md.power_save = NULL;
 	cpuidle_disable = IDLE_POWERSAVE_OFF;
-	return 0;
+	return 1;
 }
 __setup("powersave=off", powersave_off);
 
@@ -82,7 +82,7 @@
 		return;
 
 	if (cpu_has_feature(CPU_FTR_ALTIVEC))
-		asm volatile("DSSALL ; sync" ::: "memory");
+		asm volatile(PPC_DSSALL " ; sync" ::: "memory");
 
 	power4_idle_nap();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/idle_6xx.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/idle_6xx.S
@@ -129,7 +129,7 @@
 END_FTR_SECTION_IFCLR(CPU_FTR_NO_DPM)
 	mtspr	SPRN_HID0,r4
 BEGIN_FTR_SECTION
-	DSSALL
+	PPC_DSSALL
 	sync
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
 	lwz	r8,TI_LOCAL_FLAGS(r2)	/* set napping bit */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/interrupt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/interrupt.c
@@ -53,16 +53,18 @@
  */
 static notrace __always_inline bool prep_irq_for_enabled_exit(bool restartable)
 {
+	bool must_hard_disable = (exit_must_hard_disable() || !restartable);
+
 	/* This must be done with RI=1 because tracing may touch vmaps */
 	trace_hardirqs_on();
 
-	if (exit_must_hard_disable() || !restartable)
+	if (must_hard_disable)
 		__hard_EE_RI_disable();
 
 #ifdef CONFIG_PPC64
 	/* This pattern matches prep_irq_for_idle */
 	if (unlikely(lazy_irq_pending_nocheck())) {
-		if (exit_must_hard_disable() || !restartable) {
+		if (must_hard_disable) {
 			local_paca->irq_happened |= PACA_IRQ_HARD_DIS;
 			__hard_RI_enable();
 		}
@@ -81,8 +83,6 @@
 {
 	syscall_fn f;
 
-	kuep_lock();
-
 	regs->orig_gpr3 = r3;
 
 	if (IS_ENABLED(CONFIG_PPC_IRQ_SOFT_MASK_DEBUG))
@@ -148,7 +148,7 @@
 	 */
 	if (IS_ENABLED(CONFIG_PPC_TRANSACTIONAL_MEM) &&
 			unlikely(MSR_TM_TRANSACTIONAL(regs->msr)))
-		current_thread_info()->flags |= _TIF_RESTOREALL;
+		set_bits(_TIF_RESTOREALL, &current_thread_info()->flags);
 
 	/*
 	 * If the system call was made with a transaction active, doom it and
@@ -266,7 +266,7 @@
 	if (trap_is_scv(regs))
 		return;
 
-	trap = regs->trap;
+	trap = TRAP(regs);
 	// EE in HV mode sets HSRRs like 0xea0
 	if (cpu_has_feature(CPU_FTR_HVMODE) && trap == INTERRUPT_EXTERNAL)
 		trap = 0xea0;
@@ -406,7 +406,6 @@
 
 	/* Restore user access locks last */
 	kuap_user_restore(regs);
-	kuep_unlock();
 
 	return ret;
 }
@@ -529,7 +528,6 @@
 
 notrace unsigned long interrupt_exit_kernel_prepare(struct pt_regs *regs)
 {
-	unsigned long flags;
 	unsigned long ret = 0;
 	unsigned long kuap;
 	bool stack_store = current_thread_info()->flags &
@@ -546,7 +544,7 @@
 
 	kuap = kuap_get_and_assert_locked();
 
-	local_irq_save(flags);
+	local_irq_disable();
 
 	if (!arch_irq_disabled_regs(regs)) {
 		/* Returning to a kernel context with local irqs enabled. */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/interrupt_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/interrupt_64.S
@@ -30,21 +30,25 @@
 	.ifc \srr,srr
 	mfspr	r11,SPRN_SRR0
 	ld	r12,_NIP(r1)
+	clrrdi  r11,r11,2
+	clrrdi  r12,r12,2
 100:	tdne	r11,r12
-	EMIT_BUG_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
+	EMIT_WARN_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
 	mfspr	r11,SPRN_SRR1
 	ld	r12,_MSR(r1)
 100:	tdne	r11,r12
-	EMIT_BUG_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
+	EMIT_WARN_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
 	.else
 	mfspr	r11,SPRN_HSRR0
 	ld	r12,_NIP(r1)
+	clrrdi  r11,r11,2
+	clrrdi  r12,r12,2
 100:	tdne	r11,r12
-	EMIT_BUG_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
+	EMIT_WARN_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
 	mfspr	r11,SPRN_HSRR1
 	ld	r12,_MSR(r1)
 100:	tdne	r11,r12
-	EMIT_BUG_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
+	EMIT_WARN_ENTRY 100b,__FILE__,__LINE__,(BUGFLAG_WARNING | BUGFLAG_ONCE)
 	.endif
 #endif
 .endm
@@ -58,7 +62,8 @@
 	mr	r10,r1
 	ld	r1,PACAKSAVE(r13)
 	std	r10,0(r1)
-	std	r11,_NIP(r1)
+	std	r11,_LINK(r1)
+	std	r11,_NIP(r1)	/* Saved LR is also the next instruction */
 	std	r12,_MSR(r1)
 	std	r0,GPR0(r1)
 	std	r10,GPR1(r1)
@@ -81,7 +86,6 @@
 	std	r9,GPR13(r1)
 	SAVE_NVGPRS(r1)
 	std	r11,_XER(r1)
-	std	r11,_LINK(r1)
 	std	r11,_CTR(r1)
 
 	li	r11,\trapnr
@@ -162,10 +166,9 @@
 	 * The value of AMR only matters while we're in the kernel.
 	 */
 	mtcr	r2
-	ld	r2,GPR2(r1)
-	ld	r3,GPR3(r1)
-	ld	r13,GPR13(r1)
-	ld	r1,GPR1(r1)
+	REST_GPRS(2, 3, r1)
+	REST_GPR(13, r1)
+	REST_GPR(1, r1)
 	RFSCV_TO_USER
 	b	.	/* prevent speculative execution */
 
@@ -183,9 +186,8 @@
 	mtctr	r3
 	mtlr	r4
 	mtspr	SPRN_XER,r5
-	REST_10GPRS(2, r1)
-	REST_2GPRS(12, r1)
-	ld	r1,GPR1(r1)
+	REST_GPRS(2, 13, r1)
+	REST_GPR(1, r1)
 	RFI_TO_USER
 .Lsyscall_vectored_\name\()_rst_end:
 
@@ -374,10 +376,9 @@
 	 * The value of AMR only matters while we're in the kernel.
 	 */
 	mtcr	r2
-	ld	r2,GPR2(r1)
-	ld	r3,GPR3(r1)
-	ld	r13,GPR13(r1)
-	ld	r1,GPR1(r1)
+	REST_GPRS(2, 3, r1)
+	REST_GPR(13, r1)
+	REST_GPR(1, r1)
 	RFI_TO_USER
 	b	.	/* prevent speculative execution */
 
@@ -388,8 +389,7 @@
 	mtctr	r3
 	mtspr	SPRN_XER,r4
 	ld	r0,GPR0(r1)
-	REST_8GPRS(4, r1)
-	ld	r12,GPR12(r1)
+	REST_GPRS(4, 12, r1)
 	b	.Lsyscall_restore_regs_cont
 .Lsyscall_rst_end:
 
@@ -518,17 +518,14 @@
 	ld	r6,_XER(r1)
 	li	r0,0
 
-	REST_4GPRS(7, r1)
-	REST_2GPRS(11, r1)
-	REST_GPR(13, r1)
+	REST_GPRS(7, 13, r1)
 
 	mtcr	r3
 	mtlr	r4
 	mtctr	r5
 	mtspr	SPRN_XER,r6
 
-	REST_4GPRS(2, r1)
-	REST_GPR(6, r1)
+	REST_GPRS(2, 6, r1)
 	REST_GPR(0, r1)
 	REST_GPR(1, r1)
 	.ifc \srr,srr
@@ -625,8 +622,7 @@
 	ld	r6,_CCR(r1)
 	li	r0,0
 
-	REST_4GPRS(7, r1)
-	REST_2GPRS(11, r1)
+	REST_GPRS(7, 12, r1)
 
 	mtlr	r3
 	mtctr	r4
@@ -638,7 +634,7 @@
 	 */
 	std	r0,STACK_FRAME_OVERHEAD-16(r1)
 
-	REST_4GPRS(2, r1)
+	REST_GPRS(2, 5, r1)
 
 	bne-	cr1,1f /* emulate stack store */
 	mtcr	r6
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/iommu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/iommu.c
@@ -68,11 +68,9 @@
 static void iommu_debugfs_del(struct iommu_table *tbl)
 {
 	char name[10];
-	struct dentry *liobn_entry;
 
 	sprintf(name, "%08lx", tbl->it_index);
-	liobn_entry = debugfs_lookup(name, iommu_debugfs_dir);
-	debugfs_remove(liobn_entry);
+	debugfs_lookup_and_remove(name, iommu_debugfs_dir);
 }
 #else
 static void iommu_debugfs_add(struct iommu_table *tbl){}
@@ -174,17 +172,28 @@
 	return 0;
 }
 
-static struct notifier_block fail_iommu_bus_notifier = {
+/*
+ * PCI and VIO buses need separate notifier_block structs, since they're linked
+ * list nodes.  Sharing a notifier_block would mean that any notifiers later
+ * registered for PCI buses would also get called by VIO buses and vice versa.
+ */
+static struct notifier_block fail_iommu_pci_bus_notifier = {
 	.notifier_call = fail_iommu_bus_notify
 };
 
+#ifdef CONFIG_IBMVIO
+static struct notifier_block fail_iommu_vio_bus_notifier = {
+	.notifier_call = fail_iommu_bus_notify
+};
+#endif
+
 static int __init fail_iommu_setup(void)
 {
 #ifdef CONFIG_PCI
-	bus_register_notifier(&pci_bus_type, &fail_iommu_bus_notifier);
+	bus_register_notifier(&pci_bus_type, &fail_iommu_pci_bus_notifier);
 #endif
 #ifdef CONFIG_IBMVIO
-	bus_register_notifier(&vio_bus_type, &fail_iommu_bus_notifier);
+	bus_register_notifier(&vio_bus_type, &fail_iommu_vio_bus_notifier);
 #endif
 
 	return 0;
@@ -776,6 +785,11 @@
 	/* ignore reserved bit0 */
 	if (tbl->it_offset == 0)
 		start = 1;
+
+	/* Simple case with no reserved MMIO32 region */
+	if (!tbl->it_reserved_start && !tbl->it_reserved_end)
+		return find_next_bit(tbl->it_map, tbl->it_size, start) != tbl->it_size;
+
 	end = tbl->it_reserved_start - tbl->it_offset;
 	if (find_next_bit(tbl->it_map, end, start) != end)
 		return true;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/kprobes.c
@@ -140,7 +140,13 @@
 	preempt_disable();
 	prev = get_kprobe(p->addr - 1);
 	preempt_enable_no_resched();
-	if (prev && ppc_inst_prefixed(ppc_inst_read(prev->ainsn.insn))) {
+
+	/*
+	 * When prev is a ftrace-based kprobe, we don't have an insn, and it
+	 * doesn't probe for prefixed instruction.
+	 */
+	if (prev && !kprobe_ftrace(prev) &&
+	    ppc_inst_prefixed(ppc_inst_read(prev->ainsn.insn))) {
 		printk("Cannot register a kprobe on the second word of prefixed instruction\n");
 		ret = -EINVAL;
 	}
@@ -237,7 +243,7 @@
 	ri->fp = NULL;
 
 	/* Replace the return addr with trampoline addr */
-	regs->link = (unsigned long)kretprobe_trampoline;
+	regs->link = (unsigned long)__kretprobe_trampoline;
 }
 NOKPROBE_SYMBOL(arch_prepare_kretprobe);
 
@@ -403,12 +409,12 @@
  * 	- When the probed function returns, this probe
  * 		causes the handlers to fire
  */
-asm(".global kretprobe_trampoline\n"
-	".type kretprobe_trampoline, @function\n"
-	"kretprobe_trampoline:\n"
+asm(".global __kretprobe_trampoline\n"
+	".type __kretprobe_trampoline, @function\n"
+	"__kretprobe_trampoline:\n"
 	"nop\n"
 	"blr\n"
-	".size kretprobe_trampoline, .-kretprobe_trampoline\n");
+	".size __kretprobe_trampoline, .-__kretprobe_trampoline\n");
 
 /*
  * Called when the probe at kretprobe trampoline is hit
@@ -417,7 +423,7 @@
 {
 	unsigned long orig_ret_address;
 
-	orig_ret_address = __kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	orig_ret_address = __kretprobe_trampoline_handler(regs, NULL);
 	/*
 	 * We get here through one of two paths:
 	 * 1. by taking a trap -> kprobe_handler() -> here
@@ -427,7 +433,7 @@
 	 * as it is used to determine the return address from the trap.
 	 * For (2), since nip is not honoured with optprobes, we instead setup
 	 * the link register properly so that the subsequent 'blr' in
-	 * kretprobe_trampoline jumps back to the right instruction.
+	 * __kretprobe_trampoline jumps back to the right instruction.
 	 *
 	 * For nip, we should set the address to the previous instruction since
 	 * we end up emulating it in kprobe_handler(), which increments the nip
@@ -554,7 +560,7 @@
 NOKPROBE_SYMBOL(arch_deref_entry_point);
 
 static struct kprobe trampoline_p = {
-	.addr = (kprobe_opcode_t *) &kretprobe_trampoline,
+	.addr = (kprobe_opcode_t *) &__kretprobe_trampoline,
 	.pre_handler = trampoline_probe_handler
 };
 
@@ -565,7 +571,7 @@
 
 int arch_trampoline_kprobe(struct kprobe *p)
 {
-	if (p->addr == (kprobe_opcode_t *)&kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)&__kretprobe_trampoline)
 		return 1;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/kvm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/kvm.c
@@ -669,7 +669,8 @@
 	on_each_cpu(kvm_map_magic_page, &features, 1);
 
 	/* Quick self-test to see if the mapping works */
-	if (!fault_in_pages_readable((const char *)KVM_MAGIC_PAGE, sizeof(u32))) {
+	if (fault_in_readable((const char __user *)KVM_MAGIC_PAGE,
+			      sizeof(u32))) {
 		kvm_patching_worked = false;
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/l2cr_6xx.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/l2cr_6xx.S
@@ -96,7 +96,7 @@
 
 	/* Stop DST streams */
 BEGIN_FTR_SECTION
-	DSSALL
+	PPC_DSSALL
 	sync
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
 
@@ -292,7 +292,7 @@
 	isync
 
 	/* Stop DST streams */
-	DSSALL
+	PPC_DSSALL
 	sync
 
 	/* Get the current enable bit of the L3CR into r4 */
@@ -401,7 +401,7 @@
 _GLOBAL(__flush_disable_L1)
 	/* Stop pending alitvec streams and memory accesses */
 BEGIN_FTR_SECTION
-	DSSALL
+	PPC_DSSALL
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
  	sync
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/module.c
@@ -90,16 +90,17 @@
 }
 
 static __always_inline void *
-__module_alloc(unsigned long size, unsigned long start, unsigned long end)
+__module_alloc(unsigned long size, unsigned long start, unsigned long end, bool nowarn)
 {
 	pgprot_t prot = strict_module_rwx_enabled() ? PAGE_KERNEL : PAGE_KERNEL_EXEC;
+	gfp_t gfp = GFP_KERNEL | (nowarn ? __GFP_NOWARN : 0);
 
 	/*
 	 * Don't do huge page allocations for modules yet until more testing
 	 * is done. STRICT_MODULE_RWX may require extra work to support this
 	 * too.
 	 */
-	return __vmalloc_node_range(size, 1, start, end, GFP_KERNEL, prot,
+	return __vmalloc_node_range(size, 1, start, end, gfp, prot,
 				    VM_FLUSH_RESET_PERMS | VM_NO_HUGE_VMAP,
 				    NUMA_NO_NODE, __builtin_return_address(0));
 }
@@ -114,13 +115,13 @@
 
 	/* First try within 32M limit from _etext to avoid branch trampolines */
 	if (MODULES_VADDR < PAGE_OFFSET && MODULES_END > limit)
-		ptr = __module_alloc(size, limit, MODULES_END);
+		ptr = __module_alloc(size, limit, MODULES_END, true);
 
 	if (!ptr)
-		ptr = __module_alloc(size, MODULES_VADDR, MODULES_END);
+		ptr = __module_alloc(size, MODULES_VADDR, MODULES_END, false);
 
 	return ptr;
 #else
-	return __module_alloc(size, VMALLOC_START, VMALLOC_END);
+	return __module_alloc(size, VMALLOC_START, VMALLOC_END, false);
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/module_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/module_64.c
@@ -422,11 +422,17 @@
 			      const char *name)
 {
 	long reladdr;
+	func_desc_t desc;
+	int i;
 
 	if (is_mprofile_ftrace_call(name))
 		return create_ftrace_stub(entry, addr, me);
 
-	memcpy(entry->jump, ppc64_stub_insns, sizeof(ppc64_stub_insns));
+	for (i = 0; i < sizeof(ppc64_stub_insns) / sizeof(u32); i++) {
+		if (patch_instruction(&entry->jump[i],
+				      ppc_inst(ppc64_stub_insns[i])))
+			return 0;
+	}
 
 	/* Stub uses address relative to r2. */
 	reladdr = (unsigned long)entry - my_r2(sechdrs, me);
@@ -437,10 +443,24 @@
 	}
 	pr_debug("Stub %p get data from reladdr %li\n", entry, reladdr);
 
-	entry->jump[0] |= PPC_HA(reladdr);
-	entry->jump[1] |= PPC_LO(reladdr);
-	entry->funcdata = func_desc(addr);
-	entry->magic = STUB_MAGIC;
+	if (patch_instruction(&entry->jump[0],
+			      ppc_inst(entry->jump[0] | PPC_HA(reladdr))))
+		return 0;
+
+	if (patch_instruction(&entry->jump[1],
+			  ppc_inst(entry->jump[1] | PPC_LO(reladdr))))
+		return 0;
+
+	// func_desc_t is 8 bytes if ABIv2, else 16 bytes
+	desc = func_desc(addr);
+	for (i = 0; i < sizeof(func_desc_t) / sizeof(u32); i++) {
+		if (patch_instruction(((u32 *)&entry->funcdata) + i,
+				      ppc_inst(((u32 *)(&desc))[i])))
+			return 0;
+	}
+
+	if (patch_instruction(&entry->magic, ppc_inst(STUB_MAGIC)))
+		return 0;
 
 	return 1;
 }
@@ -495,8 +515,11 @@
 			me->name, *instruction, instruction);
 		return 0;
 	}
+
 	/* ld r2,R2_STACK_OFFSET(r1) */
-	*instruction = PPC_INST_LD_TOC;
+	if (patch_instruction(instruction, ppc_inst(PPC_INST_LD_TOC)))
+		return 0;
+
 	return 1;
 }
 
@@ -636,9 +659,12 @@
 			}
 
 			/* Only replace bits 2 through 26 */
-			*(uint32_t *)location
-				= (*(uint32_t *)location & ~0x03fffffc)
+			value = (*(uint32_t *)location & ~0x03fffffc)
 				| (value & 0x03fffffc);
+
+			if (patch_instruction((u32 *)location, ppc_inst(value)))
+				return -EFAULT;
+
 			break;
 
 		case R_PPC64_REL64:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/optprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/optprobes.c
@@ -56,7 +56,7 @@
 	 * has a 'nop' instruction, which can be emulated.
 	 * So further checks can be skipped.
 	 */
-	if (p->addr == (kprobe_opcode_t *)&kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)&__kretprobe_trampoline)
 		return addr + sizeof(kprobe_opcode_t);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/optprobes_head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/optprobes_head.S
@@ -10,8 +10,8 @@
 #include <asm/asm-offsets.h>
 
 #ifdef CONFIG_PPC64
-#define SAVE_30GPRS(base) SAVE_10GPRS(2,base); SAVE_10GPRS(12,base); SAVE_10GPRS(22,base)
-#define REST_30GPRS(base) REST_10GPRS(2,base); REST_10GPRS(12,base); REST_10GPRS(22,base)
+#define SAVE_30GPRS(base) SAVE_GPRS(2, 31, base)
+#define REST_30GPRS(base) REST_GPRS(2, 31, base)
 #define TEMPLATE_FOR_IMM_LOAD_INSNS	nop; nop; nop; nop; nop
 #else
 #define SAVE_30GPRS(base) stmw	r2, GPR2(base)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/paca.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/paca.c
@@ -16,7 +16,6 @@
 #include <asm/kexec.h>
 #include <asm/svm.h>
 #include <asm/ultravisor.h>
-#include <asm/rtas.h>
 
 #include "setup.h"
 
@@ -172,30 +171,6 @@
 
 #endif /* CONFIG_PPC_BOOK3S_64 */
 
-#ifdef CONFIG_PPC_PSERIES
-/**
- * new_rtas_args() - Allocates rtas args
- * @cpu:	CPU number
- * @limit:	Memory limit for this allocation
- *
- * Allocates a struct rtas_args and return it's pointer,
- * if not in Hypervisor mode
- *
- * Return:	Pointer to allocated rtas_args
- *		NULL if CPU in Hypervisor Mode
- */
-static struct rtas_args * __init new_rtas_args(int cpu, unsigned long limit)
-{
-	limit = min_t(unsigned long, limit, RTAS_INSTANTIATE_MAX);
-
-	if (early_cpu_has_feature(CPU_FTR_HVMODE))
-		return NULL;
-
-	return alloc_paca_data(sizeof(struct rtas_args), L1_CACHE_BYTES,
-			       limit, cpu);
-}
-#endif /* CONFIG_PPC_PSERIES */
-
 /* The Paca is an array with one entry per processor.  Each contains an
  * lppaca, which contains the information shared between the
  * hypervisor and Linux.
@@ -234,10 +209,6 @@
 	/* For now -- if we have threads this will be adjusted later */
 	new_paca->tcd_ptr = &new_paca->tcd;
 #endif
-
-#ifdef CONFIG_PPC_PSERIES
-	new_paca->rtas_args_reentrant = NULL;
-#endif
 }
 
 /* Put the paca pointer into r13 and SPRG_PACA */
@@ -310,9 +281,6 @@
 #ifdef CONFIG_PPC_BOOK3S_64
 	paca->slb_shadow_ptr = new_slb_shadow(cpu, limit);
 #endif
-#ifdef CONFIG_PPC_PSERIES
-	paca->rtas_args_reentrant = new_rtas_args(cpu, limit);
-#endif
 	paca_struct_size += sizeof(struct paca_struct);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/pci-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/pci-common.c
@@ -67,23 +67,35 @@
 	pci_dma_ops = dma_ops;
 }
 
-/*
- * This function should run under locking protection, specifically
- * hose_spinlock.
- */
 static int get_phb_number(struct device_node *dn)
 {
 	int ret, phb_id = -1;
-	u32 prop_32;
 	u64 prop;
 
 	/*
 	 * Try fixed PHB numbering first, by checking archs and reading
-	 * the respective device-tree properties. Firstly, try powernv by
-	 * reading "ibm,opal-phbid", only present in OPAL environment.
+	 * the respective device-tree properties. Firstly, try reading
+	 * standard "linux,pci-domain", then try reading "ibm,opal-phbid"
+	 * (only present in powernv OPAL environment), then try device-tree
+	 * alias and as the last try to use lower bits of "reg" property.
 	 */
-	ret = of_property_read_u64(dn, "ibm,opal-phbid", &prop);
+	ret = of_get_pci_domain_nr(dn);
+	if (ret >= 0) {
+		prop = ret;
+		ret = 0;
+	}
+	if (ret)
+		ret = of_property_read_u64(dn, "ibm,opal-phbid", &prop);
+
 	if (ret) {
+		ret = of_alias_get_id(dn, "pci");
+		if (ret >= 0) {
+			prop = ret;
+			ret = 0;
+		}
+	}
+	if (ret) {
+		u32 prop_32;
 		ret = of_property_read_u32_index(dn, "reg", 1, &prop_32);
 		prop = prop_32;
 	}
@@ -91,18 +103,20 @@
 	if (!ret)
 		phb_id = (int)(prop & (MAX_PHBS - 1));
 
+	spin_lock(&hose_spinlock);
+
 	/* We need to be sure to not use the same PHB number twice. */
 	if ((phb_id >= 0) && !test_and_set_bit(phb_id, phb_bitmap))
-		return phb_id;
+		goto out_unlock;
 
-	/*
-	 * If not pseries nor powernv, or if fixed PHB numbering tried to add
-	 * the same PHB number twice, then fallback to dynamic PHB numbering.
-	 */
+	/* If everything fails then fallback to dynamic PHB numbering. */
 	phb_id = find_first_zero_bit(phb_bitmap, MAX_PHBS);
 	BUG_ON(phb_id >= MAX_PHBS);
 	set_bit(phb_id, phb_bitmap);
 
+out_unlock:
+	spin_unlock(&hose_spinlock);
+
 	return phb_id;
 }
 
@@ -113,10 +127,13 @@
 	phb = zalloc_maybe_bootmem(sizeof(struct pci_controller), GFP_KERNEL);
 	if (phb == NULL)
 		return NULL;
-	spin_lock(&hose_spinlock);
+
 	phb->global_number = get_phb_number(dev);
+
+	spin_lock(&hose_spinlock);
 	list_add_tail(&phb->list_node, &hose_list);
 	spin_unlock(&hose_spinlock);
+
 	phb->dn = dev;
 	phb->is_dynamic = slab_is_available();
 #ifdef CONFIG_PPC64
@@ -342,6 +359,7 @@
 	}
 	return NULL;
 }
+EXPORT_SYMBOL(pci_find_hose_for_OF_device);
 
 struct pci_controller *pci_find_controller_for_domain(int domain_nr)
 {
@@ -1613,6 +1631,7 @@
 {
 	return pci_bus_find_capability(fake_pci_bus(hose, bus), devfn, cap);
 }
+EXPORT_SYMBOL_GPL(early_find_capability);
 
 struct device_node *pcibios_get_phb_of_node(struct pci_bus *bus)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/pci_dn.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/pci_dn.c
@@ -330,6 +330,7 @@
 	INIT_LIST_HEAD(&pdn->list);
 	parent = of_get_parent(dn);
 	pdn->parent = parent ? PCI_DN(parent) : NULL;
+	of_node_put(parent);
 	if (pdn->parent)
 		list_add_tail(&pdn->list, &pdn->parent->child_list);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/ppc_save_regs.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/ppc_save_regs.S
@@ -21,60 +21,33 @@
  * different ABIs, though).
  */
 _GLOBAL(ppc_save_regs)
-	PPC_STL	r0,0*SZL(r3)
+	/* This allows stack frame accessor macros and offsets to be used */
+	subi	r3,r3,STACK_FRAME_OVERHEAD
+	PPC_STL	r0,GPR0(r3)
 #ifdef CONFIG_PPC32
-	stmw	r2, 2*SZL(r3)
+	stmw	r2,GPR2(r3)
 #else
-	PPC_STL	r2,2*SZL(r3)
-	PPC_STL	r3,3*SZL(r3)
-	PPC_STL	r4,4*SZL(r3)
-	PPC_STL	r5,5*SZL(r3)
-	PPC_STL	r6,6*SZL(r3)
-	PPC_STL	r7,7*SZL(r3)
-	PPC_STL	r8,8*SZL(r3)
-	PPC_STL	r9,9*SZL(r3)
-	PPC_STL	r10,10*SZL(r3)
-	PPC_STL	r11,11*SZL(r3)
-	PPC_STL	r12,12*SZL(r3)
-	PPC_STL	r13,13*SZL(r3)
-	PPC_STL	r14,14*SZL(r3)
-	PPC_STL	r15,15*SZL(r3)
-	PPC_STL	r16,16*SZL(r3)
-	PPC_STL	r17,17*SZL(r3)
-	PPC_STL	r18,18*SZL(r3)
-	PPC_STL	r19,19*SZL(r3)
-	PPC_STL	r20,20*SZL(r3)
-	PPC_STL	r21,21*SZL(r3)
-	PPC_STL	r22,22*SZL(r3)
-	PPC_STL	r23,23*SZL(r3)
-	PPC_STL	r24,24*SZL(r3)
-	PPC_STL	r25,25*SZL(r3)
-	PPC_STL	r26,26*SZL(r3)
-	PPC_STL	r27,27*SZL(r3)
-	PPC_STL	r28,28*SZL(r3)
-	PPC_STL	r29,29*SZL(r3)
-	PPC_STL	r30,30*SZL(r3)
-	PPC_STL	r31,31*SZL(r3)
+	SAVE_GPRS(2, 31, r3)
 	lbz	r0,PACAIRQSOFTMASK(r13)
-	PPC_STL	r0,SOFTE-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,SOFTE(r3)
 #endif
-	/* go up one stack frame for SP */
-	PPC_LL	r4,0(r1)
-	PPC_STL	r4,1*SZL(r3)
+	/* store current SP */
+	PPC_STL	r1,GPR1(r3)
 	/* get caller's LR */
+	PPC_LL	r4,0(r1)
 	PPC_LL	r0,LRSAVE(r4)
-	PPC_STL	r0,_LINK-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_LINK(r3)
 	mflr	r0
-	PPC_STL	r0,_NIP-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_NIP(r3)
 	mfmsr	r0
-	PPC_STL	r0,_MSR-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_MSR(r3)
 	mfctr	r0
-	PPC_STL	r0,_CTR-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_CTR(r3)
 	mfxer	r0
-	PPC_STL	r0,_XER-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_XER(r3)
 	mfcr	r0
-	PPC_STL	r0,_CCR-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_CCR(r3)
 	li	r0,0
-	PPC_STL	r0,_TRAP-STACK_FRAME_OVERHEAD(r3)
-	PPC_STL	r0,ORIG_GPR3-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_TRAP(r3)
+	PPC_STL	r0,ORIG_GPR3(r3)
 	blr
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/process.c
@@ -1818,7 +1818,7 @@
 		tm_reclaim_current(0);
 #endif
 
-	memset(regs->gpr, 0, sizeof(regs->gpr));
+	memset(&regs->gpr[1], 0, sizeof(regs->gpr) - sizeof(regs->gpr[0]));
 	regs->ctr = 0;
 	regs->link = 0;
 	regs->xer = 0;
@@ -2124,12 +2124,12 @@
 		return 0;
 
 	do {
-		sp = *(unsigned long *)sp;
+		sp = READ_ONCE_NOCHECK(*(unsigned long *)sp);
 		if (!validate_sp(sp, p, STACK_FRAME_OVERHEAD) ||
 		    task_is_running(p))
 			return 0;
 		if (count > 0) {
-			ip = ((unsigned long *)sp)[STACK_FRAME_LR_SAVE];
+			ip = READ_ONCE_NOCHECK(((unsigned long *)sp)[STACK_FRAME_LR_SAVE]);
 			if (!in_sched_functions(ip))
 				return ip;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/prom.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/prom.c
@@ -751,6 +751,13 @@
 	of_scan_flat_dt(early_init_dt_scan_root, NULL);
 	of_scan_flat_dt(early_init_dt_scan_memory_ppc, NULL);
 
+	/*
+	 * As generic code authors expect to be able to use static keys
+	 * in early_param() handlers, we initialize the static keys just
+	 * before parsing early params (it's fine to call jump_label_init()
+	 * more than once).
+	 */
+	jump_label_init();
 	parse_early_param();
 
 	/* make sure we've parsed cmdline for mem= before this */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/prom_init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/prom_init.c
@@ -2928,7 +2928,7 @@
 #endif
 
 #if defined(CONFIG_PPC64) && defined(CONFIG_PPC_PMAC)
-static void __init fixup_device_tree_pmac(void)
+static void __init fixup_device_tree_pmac64(void)
 {
 	phandle u3, i2c, mpic;
 	u32 u3_rev;
@@ -2968,7 +2968,31 @@
 		     &parent, sizeof(parent));
 }
 #else
-#define fixup_device_tree_pmac()
+#define fixup_device_tree_pmac64()
+#endif
+
+#ifdef CONFIG_PPC_PMAC
+static void __init fixup_device_tree_pmac(void)
+{
+	__be32 val = 1;
+	char type[8];
+	phandle node;
+
+	// Some pmacs are missing #size-cells on escc nodes
+	for (node = 0; prom_next_node(&node); ) {
+		type[0] = '\0';
+		prom_getprop(node, "device_type", type, sizeof(type));
+		if (prom_strcmp(type, "escc"))
+			continue;
+
+		if (prom_getproplen(node, "#size-cells") != PROM_ERROR)
+			continue;
+
+		prom_setprop(node, NULL, "#size-cells", &val, sizeof(val));
+	}
+}
+#else
+static inline void fixup_device_tree_pmac(void) { }
 #endif
 
 #ifdef CONFIG_PPC_EFIKA
@@ -2991,7 +3015,7 @@
 
 	/* Check if the phy-handle property exists - bail if it does */
 	rv = prom_getprop(node, "phy-handle", prop, sizeof(prop));
-	if (!rv)
+	if (rv <= 0)
 		return;
 
 	/*
@@ -3193,6 +3217,7 @@
 	fixup_device_tree_maple_memory_controller();
 	fixup_device_tree_chrp();
 	fixup_device_tree_pmac();
+	fixup_device_tree_pmac64();
 	fixup_device_tree_efika();
 	fixup_device_tree_pasemi();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/prom_init_check.sh
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/prom_init_check.sh
@@ -13,7 +13,7 @@
 # If you really need to reference something from prom_init.o add
 # it to the list below:
 
-grep "^CONFIG_KASAN=y$" .config >/dev/null
+grep "^CONFIG_KASAN=y$" ${KCONFIG_CONFIG} >/dev/null
 if [ $? -eq 0 ]
 then
 	MEM_FUNCS="__memcpy __memset"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/ptrace/ptrace-fpu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/ptrace/ptrace-fpu.c
@@ -17,9 +17,13 @@
 
 #ifdef CONFIG_PPC_FPU_REGS
 	flush_fp_to_thread(child);
-	if (fpidx < (PT_FPSCR - PT_FPR0))
-		memcpy(data, &child->thread.TS_FPR(fpidx), sizeof(long));
-	else
+	if (fpidx < (PT_FPSCR - PT_FPR0)) {
+		if (IS_ENABLED(CONFIG_PPC32))
+			// On 32-bit the index we are passed refers to 32-bit words
+			*data = ((u32 *)child->thread.fp_state.fpr)[fpidx];
+		else
+			memcpy(data, &child->thread.TS_FPR(fpidx), sizeof(long));
+	} else
 		*data = child->thread.fp_state.fpscr;
 #else
 	*data = 0;
@@ -39,9 +43,13 @@
 
 #ifdef CONFIG_PPC_FPU_REGS
 	flush_fp_to_thread(child);
-	if (fpidx < (PT_FPSCR - PT_FPR0))
-		memcpy(&child->thread.TS_FPR(fpidx), &data, sizeof(long));
-	else
+	if (fpidx < (PT_FPSCR - PT_FPR0)) {
+		if (IS_ENABLED(CONFIG_PPC32))
+			// On 32-bit the index we are passed refers to 32-bit words
+			((u32 *)child->thread.fp_state.fpr)[fpidx] = data;
+		else
+			memcpy(&child->thread.TS_FPR(fpidx), &data, sizeof(long));
+	} else
 		child->thread.fp_state.fpscr = data;
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/ptrace/ptrace-view.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/ptrace/ptrace-view.c
@@ -290,6 +290,9 @@
 static int ppr_get(struct task_struct *target, const struct user_regset *regset,
 		   struct membuf to)
 {
+	if (!target->thread.regs)
+		return -EINVAL;
+
 	return membuf_write(&to, &target->thread.regs->ppr, sizeof(u64));
 }
 
@@ -297,6 +300,9 @@
 		   unsigned int pos, unsigned int count, const void *kbuf,
 		   const void __user *ubuf)
 {
+	if (!target->thread.regs)
+		return -EINVAL;
+
 	return user_regset_copyin(&pos, &count, &kbuf, &ubuf,
 				  &target->thread.regs->ppr, 0, sizeof(u64));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/ptrace/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/ptrace/ptrace.c
@@ -446,4 +446,7 @@
 	 * real registers.
 	 */
 	BUILD_BUG_ON(PT_DSCR < sizeof(struct user_pt_regs) / sizeof(unsigned long));
+
+	// ptrace_get/put_fpr() rely on PPC32 and VSX being incompatible
+	BUILD_BUG_ON(IS_ENABLED(CONFIG_PPC32) && IS_ENABLED(CONFIG_VSX));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/reloc_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/reloc_64.S
@@ -8,8 +8,10 @@
 #include <asm/ppc_asm.h>
 
 RELA = 7
-RELACOUNT = 0x6ffffff9
+RELASZ = 8
+RELAENT = 9
 R_PPC64_RELATIVE = 22
+R_PPC64_UADDR64 = 43
 
 /*
  * r3 = desired final address of kernel
@@ -25,29 +27,38 @@
 	add	r9,r9,r12	/* r9 has runtime addr of .rela.dyn section */
 	ld	r10,(p_st - 0b)(r12)
 	add	r10,r10,r12	/* r10 has runtime addr of _stext */
+	ld	r13,(p_sym - 0b)(r12)
+	add	r13,r13,r12	/* r13 has runtime addr of .dynsym */
 
 	/*
-	 * Scan the dynamic section for the RELA and RELACOUNT entries.
+	 * Scan the dynamic section for the RELA, RELASZ and RELAENT entries.
 	 */
 	li	r7,0
 	li	r8,0
-1:	ld	r6,0(r11)	/* get tag */
+.Ltags:
+	ld	r6,0(r11)	/* get tag */
 	cmpdi	r6,0
-	beq	4f		/* end of list */
+	beq	.Lend_of_list		/* end of list */
 	cmpdi	r6,RELA
 	bne	2f
 	ld	r7,8(r11)	/* get RELA pointer in r7 */
-	b	3f
-2:	addis	r6,r6,(-RELACOUNT)@ha
-	cmpdi	r6,RELACOUNT@l
+	b	4f
+2:	cmpdi	r6,RELASZ
 	bne	3f
-	ld	r8,8(r11)	/* get RELACOUNT value in r8 */
-3:	addi	r11,r11,16
-	b	1b
-4:	cmpdi	r7,0		/* check we have both RELA and RELACOUNT */
+	ld	r8,8(r11)	/* get RELASZ value in r8 */
+	b	4f
+3:	cmpdi	r6,RELAENT
+	bne	4f
+	ld	r12,8(r11)	/* get RELAENT value in r12 */
+4:	addi	r11,r11,16
+	b	.Ltags
+.Lend_of_list:
+	cmpdi	r7,0		/* check we have RELA, RELASZ, RELAENT */
 	cmpdi	cr1,r8,0
-	beq	6f
-	beq	cr1,6f
+	beq	.Lout
+	beq	cr1,.Lout
+	cmpdi	r12,0
+	beq	.Lout
 
 	/*
 	 * Work out linktime address of _stext and hence the
@@ -62,23 +73,39 @@
 
 	/*
 	 * Run through the list of relocations and process the
-	 * R_PPC64_RELATIVE ones.
+	 * R_PPC64_RELATIVE and R_PPC64_UADDR64 ones.
 	 */
+	divd	r8,r8,r12	/* RELASZ / RELAENT */
 	mtctr	r8
-5:	ld	r0,8(9)		/* ELF64_R_TYPE(reloc->r_info) */
+.Lrels:	ld	r0,8(r9)		/* ELF64_R_TYPE(reloc->r_info) */
 	cmpdi	r0,R_PPC64_RELATIVE
-	bne	6f
+	bne	.Luaddr64
 	ld	r6,0(r9)	/* reloc->r_offset */
 	ld	r0,16(r9)	/* reloc->r_addend */
+	b	.Lstore
+.Luaddr64:
+	srdi	r14,r0,32	/* ELF64_R_SYM(reloc->r_info) */
+	clrldi	r0,r0,32
+	cmpdi	r0,R_PPC64_UADDR64
+	bne	.Lnext
+	ld	r6,0(r9)
+	ld	r0,16(r9)
+	mulli	r14,r14,24	/* 24 == sizeof(elf64_sym) */
+	add	r14,r14,r13	/* elf64_sym[ELF64_R_SYM] */
+	ld	r14,8(r14)
+	add	r0,r0,r14
+.Lstore:
 	add	r0,r0,r3
 	stdx	r0,r7,r6
-	addi	r9,r9,24
-	bdnz	5b
-
-6:	blr
+.Lnext:
+	add	r9,r9,r12
+	bdnz	.Lrels
+.Lout:
+	blr
 
 .balign 8
 p_dyn:	.8byte	__dynamic_start - 0b
 p_rela:	.8byte	__rela_dyn_start - 0b
+p_sym:		.8byte __dynamic_symtab - 0b
 p_st:	.8byte	_stext - 0b
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/rtas.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/rtas.c
@@ -42,13 +42,21 @@
 #include <asm/time.h>
 #include <asm/mmu.h>
 #include <asm/topology.h>
-#include <asm/paca.h>
 
 /* This is here deliberately so it's only used in this file */
 void enter_rtas(unsigned long);
 
 static inline void do_enter_rtas(unsigned long args)
 {
+	unsigned long msr;
+
+	/*
+	 * Make sure MSR[RI] is currently enabled as it will be forced later
+	 * in enter_rtas.
+	 */
+	msr = mfmsr();
+	BUG_ON(!(msr & MSR_RI));
+
 	enter_rtas(args);
 
 	srr_regs_clobbered(); /* rtas uses SRRs, invalidate */
@@ -60,10 +68,10 @@
 EXPORT_SYMBOL(rtas);
 
 DEFINE_SPINLOCK(rtas_data_buf_lock);
-EXPORT_SYMBOL(rtas_data_buf_lock);
+EXPORT_SYMBOL_GPL(rtas_data_buf_lock);
 
-char rtas_data_buf[RTAS_DATA_BUF_SIZE] __cacheline_aligned;
-EXPORT_SYMBOL(rtas_data_buf);
+char rtas_data_buf[RTAS_DATA_BUF_SIZE] __aligned(SZ_4K);
+EXPORT_SYMBOL_GPL(rtas_data_buf);
 
 unsigned long rtas_rmo_buf;
 
@@ -72,7 +80,7 @@
  * This is done like this so rtas_flash can be a module.
  */
 void (*rtas_flash_term_hook)(int);
-EXPORT_SYMBOL(rtas_flash_term_hook);
+EXPORT_SYMBOL_GPL(rtas_flash_term_hook);
 
 /* RTAS use home made raw locking instead of spin_lock_irqsave
  * because those can be called from within really nasty contexts
@@ -320,7 +328,7 @@
  
 	spin_unlock(&progress_lock);
 }
-EXPORT_SYMBOL(rtas_progress);		/* needed by rtas_flash module */
+EXPORT_SYMBOL_GPL(rtas_progress);		/* needed by rtas_flash module */
 
 int rtas_token(const char *service)
 {
@@ -330,7 +338,7 @@
 	tokp = of_get_property(rtas.dev, service, NULL);
 	return tokp ? be32_to_cpu(*tokp) : RTAS_UNKNOWN_SERVICE;
 }
-EXPORT_SYMBOL(rtas_token);
+EXPORT_SYMBOL_GPL(rtas_token);
 
 int rtas_service_present(const char *service)
 {
@@ -407,7 +415,7 @@
 				buf = kmalloc(RTAS_ERROR_LOG_MAX, GFP_ATOMIC);
 		}
 		if (buf)
-			memcpy(buf, rtas_err_buf, RTAS_ERROR_LOG_MAX);
+			memmove(buf, rtas_err_buf, RTAS_ERROR_LOG_MAX);
 	}
 
 	return buf;
@@ -490,7 +498,7 @@
 	}
 	return ret;
 }
-EXPORT_SYMBOL(rtas_call);
+EXPORT_SYMBOL_GPL(rtas_call);
 
 /* For RTAS_BUSY (-2), delay for 1 millisecond.  For an extended busy status
  * code of 990n, perform the hinted delay of 10^n (last digit) milliseconds.
@@ -525,7 +533,7 @@
 
 	return ms;
 }
-EXPORT_SYMBOL(rtas_busy_delay);
+EXPORT_SYMBOL_GPL(rtas_busy_delay);
 
 static int rtas_error_rc(int rtas_rc)
 {
@@ -571,7 +579,7 @@
 		return rtas_error_rc(rc);
 	return rc;
 }
-EXPORT_SYMBOL(rtas_get_power_level);
+EXPORT_SYMBOL_GPL(rtas_get_power_level);
 
 int rtas_set_power_level(int powerdomain, int level, int *setlevel)
 {
@@ -589,7 +597,7 @@
 		return rtas_error_rc(rc);
 	return rc;
 }
-EXPORT_SYMBOL(rtas_set_power_level);
+EXPORT_SYMBOL_GPL(rtas_set_power_level);
 
 int rtas_get_sensor(int sensor, int index, int *state)
 {
@@ -607,7 +615,7 @@
 		return rtas_error_rc(rc);
 	return rc;
 }
-EXPORT_SYMBOL(rtas_get_sensor);
+EXPORT_SYMBOL_GPL(rtas_get_sensor);
 
 int rtas_get_sensor_fast(int sensor, int index, int *state)
 {
@@ -668,7 +676,7 @@
 		return rtas_error_rc(rc);
 	return rc;
 }
-EXPORT_SYMBOL(rtas_set_indicator);
+EXPORT_SYMBOL_GPL(rtas_set_indicator);
 
 /*
  * Ignoring RTAS extended delay
@@ -780,6 +788,7 @@
 
 /* Must be in the RMO region, so we place it here */
 static char rtas_os_term_buf[2048];
+static s32 ibm_os_term_token = RTAS_UNKNOWN_SERVICE;
 
 void rtas_os_term(char *str)
 {
@@ -791,16 +800,20 @@
 	 * this property may terminate the partition which we want to avoid
 	 * since it interferes with panic_timeout.
 	 */
-	if (RTAS_UNKNOWN_SERVICE == rtas_token("ibm,os-term") ||
-	    RTAS_UNKNOWN_SERVICE == rtas_token("ibm,extended-os-term"))
+	if (ibm_os_term_token == RTAS_UNKNOWN_SERVICE)
 		return;
 
 	snprintf(rtas_os_term_buf, 2048, "OS panic: %s", str);
 
+	/*
+	 * Keep calling as long as RTAS returns a "try again" status,
+	 * but don't use rtas_busy_delay(), which potentially
+	 * schedules.
+	 */
 	do {
-		status = rtas_call(rtas_token("ibm,os-term"), 1, 1, NULL,
+		status = rtas_call(ibm_os_term_token, 1, 1, NULL,
 				   __pa(rtas_os_term_buf));
-	} while (rtas_busy_delay(status));
+	} while (rtas_busy_delay_time(status));
 
 	if (status != 0)
 		printk(KERN_EMERG "ibm,os-term call failed %d\n", status);
@@ -836,59 +849,6 @@
 		pr_err("ibm,activate-firmware failed (%i)\n", fwrc);
 }
 
-#ifdef CONFIG_PPC_PSERIES
-/**
- * rtas_call_reentrant() - Used for reentrant rtas calls
- * @token:	Token for desired reentrant RTAS call
- * @nargs:	Number of Input Parameters
- * @nret:	Number of Output Parameters
- * @outputs:	Array of outputs
- * @...:	Inputs for desired RTAS call
- *
- * According to LoPAR documentation, only "ibm,int-on", "ibm,int-off",
- * "ibm,get-xive" and "ibm,set-xive" are currently reentrant.
- * Reentrant calls need their own rtas_args buffer, so not using rtas.args, but
- * PACA one instead.
- *
- * Return:	-1 on error,
- *		First output value of RTAS call if (nret > 0),
- *		0 otherwise,
- */
-int rtas_call_reentrant(int token, int nargs, int nret, int *outputs, ...)
-{
-	va_list list;
-	struct rtas_args *args;
-	unsigned long flags;
-	int i, ret = 0;
-
-	if (!rtas.entry || token == RTAS_UNKNOWN_SERVICE)
-		return -1;
-
-	local_irq_save(flags);
-	preempt_disable();
-
-	/* We use the per-cpu (PACA) rtas args buffer */
-	args = local_paca->rtas_args_reentrant;
-
-	va_start(list, outputs);
-	va_rtas_call_unlocked(args, token, nargs, nret, list);
-	va_end(list);
-
-	if (nret > 1 && outputs)
-		for (i = 0; i < nret - 1; ++i)
-			outputs[i] = be32_to_cpu(args->rets[i + 1]);
-
-	if (nret > 0)
-		ret = be32_to_cpu(args->rets[0]);
-
-	local_irq_restore(flags);
-	preempt_enable();
-
-	return ret;
-}
-
-#endif /* CONFIG_PPC_PSERIES */
-
 /**
  * Find a specific pseries error log in an RTAS extended event log.
  * @log: RTAS error/event log
@@ -974,7 +934,7 @@
 	{ "get-time-of-day", -1, -1, -1, -1, -1 },
 	{ "ibm,get-vpd", -1, 0, -1, 1, 2 },
 	{ "ibm,lpar-perftools", -1, 2, 3, -1, -1 },
-	{ "ibm,platform-dump", -1, 4, 5, -1, -1 },
+	{ "ibm,platform-dump", -1, 4, 5, -1, -1 },		/* Special cased */
 	{ "ibm,read-slot-reset-state", -1, -1, -1, -1, -1 },
 	{ "ibm,scan-log-dump", -1, 0, 1, -1, -1 },
 	{ "ibm,set-dynamic-indicator", -1, 2, -1, -1, -1 },
@@ -1023,6 +983,15 @@
 				size = 1;
 
 			end = base + size - 1;
+
+			/*
+			 * Special case for ibm,platform-dump - NULL buffer
+			 * address is used to indicate end of dump processing
+			 */
+			if (!strcmp(f->name, "ibm,platform-dump") &&
+			    base == 0)
+				return false;
+
 			if (!in_rmo_buf(base, end))
 				goto err;
 		}
@@ -1203,6 +1172,13 @@
 	no_entry = of_property_read_u32(rtas.dev, "linux,rtas-entry", &entry);
 	rtas.entry = no_entry ? rtas.base : entry;
 
+	/*
+	 * Discover these now to avoid device tree lookups in the
+	 * panic path.
+	 */
+	if (of_property_read_bool(rtas.dev, "ibm,extended-os-term"))
+		ibm_os_term_token = rtas_token("ibm,os-term");
+
 	/* If RTAS was found, allocate the RMO buffer for it and look for
 	 * the stop-self token if any
 	 */
@@ -1235,6 +1211,12 @@
 	entryp = of_get_flat_dt_prop(node, "linux,rtas-entry", NULL);
 	sizep  = of_get_flat_dt_prop(node, "rtas-size", NULL);
 
+#ifdef CONFIG_PPC64
+	/* need this feature to decide the crashkernel offset */
+	if (of_get_flat_dt_prop(node, "ibm,hypertas-functions", NULL))
+		powerpc_firmware_features |= FW_FEATURE_LPAR;
+#endif
+
 	if (basep && entryp && sizep) {
 		rtas.base = *basep;
 		rtas.entry = *entryp;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/rtas_flash.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/rtas_flash.c
@@ -710,9 +710,9 @@
 	if (!rtas_validate_flash_data.buf)
 		return -ENOMEM;
 
-	flash_block_cache = kmem_cache_create("rtas_flash_cache",
-					      RTAS_BLK_SIZE, RTAS_BLK_SIZE, 0,
-					      NULL);
+	flash_block_cache = kmem_cache_create_usercopy("rtas_flash_cache",
+						       RTAS_BLK_SIZE, RTAS_BLK_SIZE,
+						       0, 0, RTAS_BLK_SIZE, NULL);
 	if (!flash_block_cache) {
 		printk(KERN_ERR "%s: failed to create block cache\n",
 				__func__);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/security.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/security.c
@@ -363,26 +363,27 @@
 
 static int ssb_prctl_get(struct task_struct *task)
 {
+	/*
+	 * The STF_BARRIER feature is on by default, so if it's off that means
+	 * firmware has explicitly said the CPU is not vulnerable via either
+	 * the hypercall or device tree.
+	 */
+	if (!security_ftr_enabled(SEC_FTR_STF_BARRIER))
+		return PR_SPEC_NOT_AFFECTED;
+
+	/*
+	 * If the system's CPU has no known barrier (see setup_stf_barrier())
+	 * then assume that the CPU is not vulnerable.
+	 */
 	if (stf_enabled_flush_types == STF_BARRIER_NONE)
-		/*
-		 * We don't have an explicit signal from firmware that we're
-		 * vulnerable or not, we only have certain CPU revisions that
-		 * are known to be vulnerable.
-		 *
-		 * We assume that if we're on another CPU, where the barrier is
-		 * NONE, then we are not vulnerable.
-		 */
 		return PR_SPEC_NOT_AFFECTED;
-	else
-		/*
-		 * If we do have a barrier type then we are vulnerable. The
-		 * barrier is not a global or per-process mitigation, so the
-		 * only value we can report here is PR_SPEC_ENABLE, which
-		 * appears as "vulnerable" in /proc.
-		 */
-		return PR_SPEC_ENABLE;
 
-	return -EINVAL;
+	/*
+	 * Otherwise the CPU is vulnerable. The barrier is not a global or
+	 * per-process mitigation, so the only value that can be reported here
+	 * is PR_SPEC_ENABLE, which appears as "vulnerable" in /proc.
+	 */
+	return PR_SPEC_ENABLE;
 }
 
 int arch_prctl_spec_ctrl_get(struct task_struct *task, unsigned long which)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/secvar-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/secvar-sysfs.c
@@ -26,15 +26,18 @@
 	const char *format;
 
 	node = of_find_compatible_node(NULL, NULL, "ibm,secvar-backend");
-	if (!of_device_is_available(node))
-		return -ENODEV;
+	if (!of_device_is_available(node)) {
+		rc = -ENODEV;
+		goto out;
+	}
 
 	rc = of_property_read_string(node, "format", &format);
 	if (rc)
-		return rc;
+		goto out;
 
 	rc = sprintf(buf, "%s\n", format);
 
+out:
 	of_node_put(node);
 
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/setup-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/setup-common.c
@@ -33,6 +33,7 @@
 #include <linux/of_platform.h>
 #include <linux/hugetlb.h>
 #include <linux/pgtable.h>
+#include <linux/security.h>
 #include <asm/io.h>
 #include <asm/paca.h>
 #include <asm/prom.h>
@@ -65,6 +66,7 @@
 #include <asm/cpu_has_feature.h>
 #include <asm/kasan.h>
 #include <asm/mce.h>
+#include <asm/secure_boot.h>
 
 #include "setup.h"
 
@@ -852,6 +854,16 @@
 	 */
 	initialize_cache_info();
 
+	/*
+	 * Lock down the kernel if booted in secure mode. This is required to
+	 * maintain kernel integrity.
+	 */
+	if (IS_ENABLED(CONFIG_LOCK_DOWN_IN_SECURE_BOOT)) {
+		if (is_ppc_secureboot_enabled())
+			security_lock_kernel_down("PowerNV Secure Boot mode",
+						  LOCKDOWN_INTEGRITY_MAX);
+	}
+
 	/* Initialize RTAS if available. */
 	rtas_initialize();
 
@@ -887,6 +899,9 @@
 
 	/* Parse memory topology */
 	mem_topology_setup();
+	/* Set max_mapnr before paging_init() */
+	set_max_mapnr(max_pfn);
+	high_memory = (void *)__va(max_low_pfn * PAGE_SIZE);
 
 	/*
 	 * Release secondary cpus out of their spinloops at 0x60 now that
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/setup_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/setup_64.c
@@ -825,6 +825,7 @@
 
 unsigned long __per_cpu_offset[NR_CPUS] __read_mostly;
 EXPORT_SYMBOL(__per_cpu_offset);
+DEFINE_STATIC_KEY_FALSE(__percpu_first_chunk_is_paged);
 
 static void __init pcpu_populate_pte(unsigned long addr)
 {
@@ -904,6 +905,7 @@
 	if (rc < 0)
 		panic("cannot initialize percpu area (err=%d)", rc);
 
+	static_key_enable(&__percpu_first_chunk_is_paged.key);
 	delta = (unsigned long)pcpu_base_addr - (unsigned long)__per_cpu_start;
 	for_each_possible_cpu(cpu) {
                 __per_cpu_offset[cpu] = delta + pcpu_unit_offsets[cpu];
@@ -950,6 +952,7 @@
 	hardlockup_detector_disable();
 #else
 	if (firmware_has_feature(FW_FEATURE_LPAR)) {
+		check_kvm_guest();
 		if (is_kvm_guest())
 			hardlockup_detector_disable();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/signal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/signal.h
@@ -25,8 +25,14 @@
 
 	return __get_user(dst->sig[0], (u64 __user *)&src->sig[0]);
 }
-#define unsafe_get_user_sigset(dst, src, label) \
-	unsafe_get_user((dst)->sig[0], (u64 __user *)&(src)->sig[0], label)
+#define unsafe_get_user_sigset(dst, src, label) do {			\
+	sigset_t *__dst = dst;						\
+	const sigset_t __user *__src = src;				\
+	int i;								\
+									\
+	for (i = 0; i < _NSIG_WORDS; i++)				\
+		unsafe_get_user(__dst->sig[i], &__src->sig[i], label);	\
+} while (0)
 
 #ifdef CONFIG_VSX
 extern unsigned long copy_vsx_to_user(void __user *to,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/signal_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/signal_32.c
@@ -258,8 +258,9 @@
 #endif
 }
 
-static int __unsafe_save_user_regs(struct pt_regs *regs, struct mcontext __user *frame,
-				   struct mcontext __user *tm_frame, int ctx_has_vsx_region)
+static __always_inline int
+__unsafe_save_user_regs(struct pt_regs *regs, struct mcontext __user *frame,
+			struct mcontext __user *tm_frame, int ctx_has_vsx_region)
 {
 	unsigned long msr = regs->msr;
 
@@ -358,8 +359,9 @@
 		current->thread.ckvrsave = mfspr(SPRN_VRSAVE);
 }
 
-static int save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
-				    struct mcontext __user *tm_frame, unsigned long msr)
+static __always_inline int
+save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
+			 struct mcontext __user *tm_frame, unsigned long msr)
 {
 	/* Save both sets of general registers */
 	unsafe_save_general_regs(&current->thread.ckpt_regs, frame, failed);
@@ -438,8 +440,9 @@
 #else
 static void prepare_save_tm_user_regs(void) { }
 
-static int save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
-				    struct mcontext __user *tm_frame, unsigned long msr)
+static __always_inline int
+save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
+			 struct mcontext __user *tm_frame, unsigned long msr)
 {
 	return 0;
 }
@@ -1048,7 +1051,7 @@
 	if (new_ctx == NULL)
 		return 0;
 	if (!access_ok(new_ctx, ctx_size) ||
-	    fault_in_pages_readable((u8 __user *)new_ctx, ctx_size))
+	    fault_in_readable((char __user *)new_ctx, ctx_size))
 		return -EFAULT;
 
 	/*
@@ -1062,8 +1065,10 @@
 	 * or if another thread unmaps the region containing the context.
 	 * We kill the task with a SIGSEGV in this situation.
 	 */
-	if (do_setcontext(new_ctx, regs, 0))
-		do_exit(SIGSEGV);
+	if (do_setcontext(new_ctx, regs, 0)) {
+		force_exit_sig(SIGSEGV);
+		return -EFAULT;
+	}
 
 	set_thread_flag(TIF_RESTOREALL);
 	return 0;
@@ -1237,7 +1242,7 @@
 #endif
 
 	if (!access_ok(ctx, sizeof(*ctx)) ||
-	    fault_in_pages_readable((u8 __user *)ctx, sizeof(*ctx)))
+	    fault_in_readable((char __user *)ctx, sizeof(*ctx)))
 		return -EFAULT;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/signal_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/signal_64.c
@@ -688,7 +688,7 @@
 	if (new_ctx == NULL)
 		return 0;
 	if (!access_ok(new_ctx, ctx_size) ||
-	    fault_in_pages_readable((u8 __user *)new_ctx, ctx_size))
+	    fault_in_readable((char __user *)new_ctx, ctx_size))
 		return -EFAULT;
 
 	/*
@@ -703,15 +703,18 @@
 	 * We kill the task with a SIGSEGV in this situation.
 	 */
 
-	if (__get_user_sigset(&set, &new_ctx->uc_sigmask))
-		do_exit(SIGSEGV);
+	if (__get_user_sigset(&set, &new_ctx->uc_sigmask)) {
+		force_exit_sig(SIGSEGV);
+		return -EFAULT;
+	}
 	set_current_blocked(&set);
 
 	if (!user_read_access_begin(new_ctx, ctx_size))
 		return -EFAULT;
 	if (__unsafe_restore_sigcontext(current, NULL, 0, &new_ctx->uc_mcontext)) {
 		user_read_access_end();
-		do_exit(SIGSEGV);
+		force_exit_sig(SIGSEGV);
+		return -EFAULT;
 	}
 	user_read_access_end();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/smp.c
@@ -61,6 +61,7 @@
 #include <asm/cpu_has_feature.h>
 #include <asm/ftrace.h>
 #include <asm/kup.h>
+#include <asm/fadump.h>
 
 #ifdef DEBUG
 #include <asm/udbg.h>
@@ -621,6 +622,45 @@
 #endif
 
 #ifdef CONFIG_NMI_IPI
+static void crash_stop_this_cpu(struct pt_regs *regs)
+#else
+static void crash_stop_this_cpu(void *dummy)
+#endif
+{
+	/*
+	 * Just busy wait here and avoid marking CPU as offline to ensure
+	 * register data is captured appropriately.
+	 */
+	while (1)
+		cpu_relax();
+}
+
+void crash_smp_send_stop(void)
+{
+	static bool stopped = false;
+
+	/*
+	 * In case of fadump, register data for all CPUs is captured by f/w
+	 * on ibm,os-term rtas call. Skip IPI callbacks to other CPUs before
+	 * this rtas call to avoid tricky post processing of those CPUs'
+	 * backtraces.
+	 */
+	if (should_fadump_crash())
+		return;
+
+	if (stopped)
+		return;
+
+	stopped = true;
+
+#ifdef CONFIG_NMI_IPI
+	smp_send_nmi_ipi(NMI_IPI_ALL_OTHERS, crash_stop_this_cpu, 1000000);
+#else
+	smp_call_function(crash_stop_this_cpu, NULL, 0);
+#endif /* CONFIG_NMI_IPI */
+}
+
+#ifdef CONFIG_NMI_IPI
 static void nmi_stop_this_cpu(struct pt_regs *regs)
 {
 	/*
@@ -1640,10 +1680,12 @@
 	BUG();
 }
 
+#ifdef CONFIG_PROFILING
 int setup_profiling_timer(unsigned int multiplier)
 {
 	return 0;
 }
+#endif
 
 static void fixup_topology(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/stacktrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/stacktrace.c
@@ -155,7 +155,7 @@
 		 * Mark stacktraces with kretprobed functions on them
 		 * as unreliable.
 		 */
-		if (ip == (unsigned long)kretprobe_trampoline)
+		if (ip == (unsigned long)__kretprobe_trampoline)
 			return -EINVAL;
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/swsusp_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/swsusp_32.S
@@ -181,7 +181,7 @@
 #ifdef CONFIG_ALTIVEC
 	/* Stop pending alitvec streams and memory accesses */
 BEGIN_FTR_SECTION
-	DSSALL
+	PPC_DSSALL
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
 #endif
  	sync
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/swsusp_asm64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/swsusp_asm64.S
@@ -142,7 +142,7 @@
 _GLOBAL(swsusp_arch_resume)
 	/* Stop pending alitvec streams and memory accesses */
 BEGIN_FTR_SECTION
-	DSSALL
+	PPC_DSSALL
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
 	sync
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/sys_ppc32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/sys_ppc32.c
@@ -56,18 +56,6 @@
 	return sys_mmap(addr, len, prot, flags, fd, pgoff << 12);
 }
 
-/* 
- * long long munging:
- * The 32 bit ABI passes long longs in an odd even register pair.
- * High and low parts are swapped depending on endian mode,
- * so define a macro (similar to mips linux32) to handle that.
- */
-#ifdef __LITTLE_ENDIAN__
-#define merge_64(low, high) ((u64)high << 32) | low
-#else
-#define merge_64(high, low) ((u64)high << 32) | low
-#endif
-
 compat_ssize_t compat_sys_pread64(unsigned int fd, char __user *ubuf, compat_size_t count,
 			     u32 reg6, u32 pos1, u32 pos2)
 {
@@ -94,7 +82,7 @@
 asmlinkage long compat_sys_fallocate(int fd, int mode, u32 offset1, u32 offset2,
 				     u32 len1, u32 len2)
 {
-	return ksys_fallocate(fd, mode, ((loff_t)offset1 << 32) | offset2,
+	return ksys_fallocate(fd, mode, merge_64(offset1, offset2),
 			     merge_64(len1, len2));
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/syscalls.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/syscalls.c
@@ -99,8 +99,8 @@
 long ppc_fadvise64_64(int fd, int advice, u32 offset_high, u32 offset_low,
 		      u32 len_high, u32 len_low)
 {
-	return ksys_fadvise64_64(fd, (u64)offset_high << 32 | offset_low,
-				 (u64)len_high << 32 | len_low, advice);
+	return ksys_fadvise64_64(fd, merge_64(offset_high, offset_low),
+				 merge_64(len_high, len_low), advice);
 }
 
 SYSCALL_DEFINE0(switch_endian)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/syscalls/syscall.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/syscalls/syscall.tbl
@@ -495,7 +495,7 @@
 412	32	utimensat_time64		sys_utimensat			sys_utimensat
 413	32	pselect6_time64			sys_pselect6			compat_sys_pselect6_time64
 414	32	ppoll_time64			sys_ppoll			compat_sys_ppoll_time64
-416	32	io_pgetevents_time64		sys_io_pgetevents		sys_io_pgetevents
+416	32	io_pgetevents_time64		sys_io_pgetevents		compat_sys_io_pgetevents_time64
 417	32	recvmmsg_time64			sys_recvmmsg			compat_sys_recvmmsg_time64
 418	32	mq_timedsend_time64		sys_mq_timedsend		sys_mq_timedsend
 419	32	mq_timedreceive_time64		sys_mq_timedreceive		sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/systbl.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/systbl.S
@@ -18,6 +18,7 @@
 	.p2align	3
 #define __SYSCALL(nr, entry)	.8byte entry
 #else
+	.p2align	2
 #define __SYSCALL(nr, entry)	.long entry
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/time.c
@@ -450,7 +450,7 @@
 #define calc_cputime_factors()
 #endif
 
-void __delay(unsigned long loops)
+void __no_kcsan __delay(unsigned long loops)
 {
 	unsigned long start;
 
@@ -471,7 +471,7 @@
 }
 EXPORT_SYMBOL(__delay);
 
-void udelay(unsigned long usecs)
+void __no_kcsan udelay(unsigned long usecs)
 {
 	__delay(tb_ticks_per_usec * usecs);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/tm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/tm.S
@@ -226,11 +226,8 @@
 
 	/* Sync the userland GPRs 2-12, 14-31 to thread->regs: */
 	SAVE_GPR(0, r7)				/* user r0 */
-	SAVE_GPR(2, r7)				/* user r2 */
-	SAVE_4GPRS(3, r7)			/* user r3-r6 */
-	SAVE_GPR(8, r7)				/* user r8 */
-	SAVE_GPR(9, r7)				/* user r9 */
-	SAVE_GPR(10, r7)			/* user r10 */
+	SAVE_GPRS(2, 6, r7)			/* user r2-r6 */
+	SAVE_GPRS(8, 10, r7)			/* user r8-r10 */
 	ld	r3, GPR1(r1)			/* user r1 */
 	ld	r4, GPR7(r1)			/* user r7 */
 	ld	r5, GPR11(r1)			/* user r11 */
@@ -445,12 +442,9 @@
 	ld	r6, THREAD_TM_PPR(r3)
 
 	REST_GPR(0, r7)				/* GPR0 */
-	REST_2GPRS(2, r7)			/* GPR2-3 */
-	REST_GPR(4, r7)				/* GPR4 */
-	REST_4GPRS(8, r7)			/* GPR8-11 */
-	REST_2GPRS(12, r7)			/* GPR12-13 */
-
-	REST_NVGPRS(r7)				/* GPR14-31 */
+	REST_GPRS(2, 4, r7)			/* GPR2-4 */
+	REST_GPRS(8, 12, r7)			/* GPR8-12 */
+	REST_GPRS(14, 31, r7)			/* GPR14-31 */
 
 	/* Load up PPR and DSCR here so we don't run with user values for long */
 	mtspr	SPRN_DSCR, r5
@@ -486,18 +480,24 @@
 	REST_GPR(6, r7)
 
 	/*
-	 * Store r1 and r5 on the stack so that we can access them after we
-	 * clear MSR RI.
+	 * Store user r1 and r5 and r13 on the stack (in the unused save
+	 * areas / compiler reserved areas), so that we can access them after
+	 * we clear MSR RI.
 	 */
 
 	REST_GPR(5, r7)
 	std	r5, -8(r1)
-	ld	r5, GPR1(r7)
+	ld	r5, GPR13(r7)
 	std	r5, -16(r1)
+	ld	r5, GPR1(r7)
+	std	r5, -24(r1)
 
 	REST_GPR(7, r7)
 
-	/* Clear MSR RI since we are about to use SCRATCH0. EE is already off */
+	/* Stash the stack pointer away for use after recheckpoint */
+	std	r1, PACAR1(r13)
+
+	/* Clear MSR RI since we are about to clobber r13. EE is already off */
 	li	r5, 0
 	mtmsrd	r5, 1
 
@@ -508,9 +508,9 @@
 	 * until we turn MSR RI back on.
 	 */
 
-	SET_SCRATCH0(r1)
 	ld	r5, -8(r1)
-	ld	r1, -16(r1)
+	ld	r13, -16(r1)
+	ld	r1, -24(r1)
 
 	/* Commit register state as checkpointed state: */
 	TRECHKPT
@@ -526,9 +526,9 @@
 	 */
 
 	GET_PACA(r13)
-	GET_SCRATCH0(r1)
+	ld	r1, PACAR1(r13)
 
-	/* R1 is restored, so we are recoverable again.  EE is still off */
+	/* R13, R1 is restored, so we are recoverable again.  EE is still off */
 	li	r4, MSR_RI
 	mtmsrd	r4, 1
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/trace/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/trace/ftrace.c
@@ -336,9 +336,7 @@
 
 	/* Is this a known long jump tramp? */
 	for (i = 0; i < NUM_FTRACE_TRAMPS; i++)
-		if (!ftrace_tramps[i])
-			break;
-		else if (ftrace_tramps[i] == tramp)
+		if (ftrace_tramps[i] == tramp)
 			return 0;
 
 	/* Is this a known plt tramp? */
@@ -881,6 +879,17 @@
 
 extern unsigned int ftrace_tramp_text[], ftrace_tramp_init[];
 
+void ftrace_free_init_tramp(void)
+{
+	int i;
+
+	for (i = 0; i < NUM_FTRACE_TRAMPS && ftrace_tramps[i]; i++)
+		if (ftrace_tramps[i] == (unsigned long)ftrace_tramp_init) {
+			ftrace_tramps[i] = 0;
+			return;
+		}
+}
+
 int __init ftrace_dyn_arch_init(void)
 {
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/trace/ftrace_64_mprofile.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/trace/ftrace_64_mprofile.S
@@ -36,23 +36,25 @@
 	/* Save the original return address in A's stack frame */
 	std	r0,LRSAVE(r1)
 
+	/* Create a minimal stack frame for representing B */
+	stdu	r1, -STACK_FRAME_MIN_SIZE(r1)
+
 	/* Create our stack frame + pt_regs */
 	stdu	r1,-SWITCH_FRAME_SIZE(r1)
 
 	/* Save all gprs to pt_regs */
 	SAVE_GPR(0, r1)
-	SAVE_10GPRS(2, r1)
+	SAVE_GPRS(2, 11, r1)
 
 	/* Ok to continue? */
 	lbz	r3, PACA_FTRACE_ENABLED(r13)
 	cmpdi	r3, 0
 	beq	ftrace_no_trace
 
-	SAVE_10GPRS(12, r1)
-	SAVE_10GPRS(22, r1)
+	SAVE_GPRS(12, 31, r1)
 
 	/* Save previous stack pointer (r1) */
-	addi	r8, r1, SWITCH_FRAME_SIZE
+	addi	r8, r1, SWITCH_FRAME_SIZE+STACK_FRAME_MIN_SIZE
 	std	r8, GPR1(r1)
 
 	/* Load special regs for save below */
@@ -65,6 +67,8 @@
 	mflr	r7
 	/* Save it as pt_regs->nip */
 	std     r7, _NIP(r1)
+	/* Also save it in B's stackframe header for proper unwind */
+	std	r7, LRSAVE+SWITCH_FRAME_SIZE(r1)
 	/* Save the read LR in pt_regs->link */
 	std     r0, _LINK(r1)
 
@@ -108,10 +112,8 @@
 #endif
 
 	/* Restore gprs */
-	REST_GPR(0,r1)
-	REST_10GPRS(2,r1)
-	REST_10GPRS(12,r1)
-	REST_10GPRS(22,r1)
+	REST_GPR(0, r1)
+	REST_GPRS(2, 31, r1)
 
 	/* Restore possibly modified LR */
 	ld	r0, _LINK(r1)
@@ -121,7 +123,7 @@
 	ld	r2, 24(r1)
 
 	/* Pop our stack frame */
-	addi r1, r1, SWITCH_FRAME_SIZE
+	addi r1, r1, SWITCH_FRAME_SIZE+STACK_FRAME_MIN_SIZE
 
 #ifdef CONFIG_LIVEPATCH
         /* Based on the cmpd above, if the NIP was altered handle livepatch */
@@ -145,7 +147,7 @@
 	mflr	r3
 	mtctr	r3
 	REST_GPR(3, r1)
-	addi	r1, r1, SWITCH_FRAME_SIZE
+	addi	r1, r1, SWITCH_FRAME_SIZE+STACK_FRAME_MIN_SIZE
 	mtlr	r0
 	bctr
 
@@ -153,11 +155,14 @@
 	/* Save the original return address in A's stack frame */
 	std	r0, LRSAVE(r1)
 
+	/* Create a minimal stack frame for representing B */
+	stdu	r1, -STACK_FRAME_MIN_SIZE(r1)
+
 	/* Create our stack frame + pt_regs */
 	stdu	r1, -SWITCH_FRAME_SIZE(r1)
 
 	/* Save all gprs to pt_regs */
-	SAVE_8GPRS(3, r1)
+	SAVE_GPRS(3, 10, r1)
 
 	lbz	r3, PACA_FTRACE_ENABLED(r13)
 	cmpdi	r3, 0
@@ -166,6 +171,7 @@
 	/* Get the _mcount() call site out of LR */
 	mflr	r7
 	std     r7, _NIP(r1)
+	std	r7, LRSAVE+SWITCH_FRAME_SIZE(r1)
 
 	/* Save callee's TOC in the ABI compliant location */
 	std	r2, 24(r1)
@@ -194,13 +200,13 @@
 	mtctr	r3
 
 	/* Restore gprs */
-	REST_8GPRS(3,r1)
+	REST_GPRS(3, 10, r1)
 
 	/* Restore callee's TOC */
 	ld	r2, 24(r1)
 
 	/* Pop our stack frame */
-	addi	r1, r1, SWITCH_FRAME_SIZE
+	addi	r1, r1, SWITCH_FRAME_SIZE+STACK_FRAME_MIN_SIZE
 
 	/* Reload original LR */
 	ld	r0, LRSAVE(r1)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/traps.c
@@ -245,7 +245,7 @@
 
 	if (panic_on_oops)
 		panic("Fatal exception");
-	do_exit(signr);
+	make_task_dead(signr);
 }
 NOKPROBE_SYMBOL(oops_end);
 
@@ -792,9 +792,9 @@
 void die_mce(const char *str, struct pt_regs *regs, long err)
 {
 	/*
-	 * The machine check wants to kill the interrupted context, but
-	 * do_exit() checks for in_interrupt() and panics in that case, so
-	 * exit the irq/nmi before calling die.
+	 * The machine check wants to kill the interrupted context,
+	 * but make_task_dead() checks for in_interrupt() and panics
+	 * in that case, so exit the irq/nmi before calling die.
 	 */
 	if (in_nmi())
 		nmi_exit();
@@ -1148,6 +1148,7 @@
 		__single_step_exception(regs);
 }
 
+#ifdef CONFIG_PPC_FPU_REGS
 static inline int __parse_fpscr(unsigned long fpscr)
 {
 	int ret = FPE_FLTUNK;
@@ -1174,6 +1175,7 @@
 
 	return ret;
 }
+#endif
 
 static void parse_fpe(struct pt_regs *regs)
 {
@@ -1421,10 +1423,12 @@
 	return -EINVAL;
 }
 
+#ifdef CONFIG_GENERIC_BUG
 int is_valid_bugaddr(unsigned long addr)
 {
 	return is_kernel_addr(addr);
 }
+#endif
 
 #ifdef CONFIG_MATH_EMULATION
 static int emulate_math(struct pt_regs *regs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/vector.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/vector.S
@@ -32,6 +32,7 @@
 	mfvscr	v0
 	li	r4, VRSTATE_VSCR
 	stvx	v0, r4, r3
+	lvx	v0, 0, r3
 	blr
 EXPORT_SYMBOL(store_vr_state)
 
@@ -104,6 +105,7 @@
 	mfvscr	v0
 	li	r4,VRSTATE_VSCR
 	stvx	v0,r4,r7
+	lvx	v0,0,r7
 	blr
 
 #ifdef CONFIG_VSX
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/vmlinux.lds.S
@@ -8,6 +8,7 @@
 #define BSS_FIRST_SECTIONS *(.bss.prominit)
 #define EMITS_PT_NOTE
 #define RO_EXCEPTION_TABLE_ALIGN	0
+#define RUNTIME_DISCARD_EXIT
 
 #define SOFT_MASK_TABLE(align)						\
 	. = ALIGN(align);						\
@@ -32,6 +33,10 @@
 
 #define STRICT_ALIGN_SIZE	(1 << CONFIG_DATA_SHIFT)
 
+#if STRICT_ALIGN_SIZE < PAGE_SIZE
+#error "CONFIG_DATA_SHIFT must be >= PAGE_SHIFT"
+#endif
+
 ENTRY(_stext)
 
 PHDRS {
@@ -143,6 +148,12 @@
 	SOFT_MASK_TABLE(8)
 	RESTART_TABLE(8)
 
+	.opd : AT(ADDR(.opd) - LOAD_OFFSET) {
+		__start_opd = .;
+		KEEP(*(.opd))
+		__end_opd = .;
+	}
+
 	. = ALIGN(8);
 	__stf_entry_barrier_fixup : AT(ADDR(__stf_entry_barrier_fixup) - LOAD_OFFSET) {
 		__start___stf_entry_barrier_fixup = .;
@@ -204,12 +215,16 @@
 	}
 #endif
 
+	/*
+	 * Various code relies on __init_begin being at the strict RWX boundary.
+	 */
+	. = ALIGN(STRICT_ALIGN_SIZE);
+	__srwx_boundary = .;
+	__init_begin = .;
+
 /*
  * Init sections discarded at runtime
  */
-	. = ALIGN(STRICT_ALIGN_SIZE);
-	__init_begin = .;
-	. = ALIGN(PAGE_SIZE);
 	.init.text : AT(ADDR(.init.text) - LOAD_OFFSET) {
 		_sinittext = .;
 		INIT_TEXT
@@ -275,9 +290,7 @@
 	. = ALIGN(8);
 	.dynsym : AT(ADDR(.dynsym) - LOAD_OFFSET)
 	{
-#ifdef CONFIG_PPC32
 		__dynamic_symtab = .;
-#endif
 		*(.dynsym)
 	}
 	.dynstr : AT(ADDR(.dynstr) - LOAD_OFFSET) { *(.dynstr) }
@@ -339,21 +352,13 @@
 		*(.branch_lt)
 	}
 
-	.opd : AT(ADDR(.opd) - LOAD_OFFSET) {
-		__start_opd = .;
-		KEEP(*(.opd))
-		__end_opd = .;
-	}
-
-	. = ALIGN(256);
-	.got : AT(ADDR(.got) - LOAD_OFFSET) {
-		__toc_start = .;
+	.got : AT(ADDR(.got) - LOAD_OFFSET) ALIGN(256) {
+		*(.got)
 #ifndef CONFIG_RELOCATABLE
 		__prom_init_toc_start = .;
-		arch/powerpc/kernel/prom_init.o*(.toc .got)
+		arch/powerpc/kernel/prom_init.o*(.toc)
 		__prom_init_toc_end = .;
 #endif
-		*(.got)
 		*(.toc)
 	}
 #endif
@@ -401,9 +406,12 @@
 	DISCARDS
 	/DISCARD/ : {
 		*(*.EMB.apuinfo)
-		*(.glink .iplt .plt .rela* .comment)
+		*(.glink .iplt .plt .comment)
 		*(.gnu.version*)
 		*(.gnu.attributes)
 		*(.eh_frame)
+#ifndef CONFIG_RELOCATABLE
+		*(.rela*)
+#endif
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kernel/watchdog.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kernel/watchdog.c
@@ -135,6 +135,10 @@
 {
 	cpumask_or(&wd_smp_cpus_stuck, &wd_smp_cpus_stuck, cpumask);
 	cpumask_andnot(&wd_smp_cpus_pending, &wd_smp_cpus_pending, cpumask);
+	/*
+	 * See wd_smp_clear_cpu_pending()
+	 */
+	smp_mb();
 	if (cpumask_empty(&wd_smp_cpus_pending)) {
 		wd_smp_last_reset_tb = tb;
 		cpumask_andnot(&wd_smp_cpus_pending,
@@ -187,6 +191,12 @@
 	if (sysctl_hardlockup_all_cpu_backtrace)
 		trigger_allbutself_cpu_backtrace();
 
+	/*
+	 * Force flush any remote buffers that might be stuck in IRQ context
+	 * and therefore could not run their irq_work.
+	 */
+	printk_trigger_flush();
+
 	if (hardlockup_panic)
 		nmi_panic(NULL, "Hard LOCKUP");
 
@@ -215,13 +225,44 @@
 
 			cpumask_clear_cpu(cpu, &wd_smp_cpus_stuck);
 			wd_smp_unlock(&flags);
+		} else {
+			/*
+			 * The last CPU to clear pending should have reset the
+			 * watchdog so we generally should not find it empty
+			 * here if our CPU was clear. However it could happen
+			 * due to a rare race with another CPU taking the
+			 * last CPU out of the mask concurrently.
+			 *
+			 * We can't add a warning for it. But just in case
+			 * there is a problem with the watchdog that is causing
+			 * the mask to not be reset, try to kick it along here.
+			 */
+			if (unlikely(cpumask_empty(&wd_smp_cpus_pending)))
+				goto none_pending;
 		}
 		return;
 	}
+
 	cpumask_clear_cpu(cpu, &wd_smp_cpus_pending);
+
+	/*
+	 * Order the store to clear pending with the load(s) to check all
+	 * words in the pending mask to check they are all empty. This orders
+	 * with the same barrier on another CPU. This prevents two CPUs
+	 * clearing the last 2 pending bits, but neither seeing the other's
+	 * store when checking if the mask is empty, and missing an empty
+	 * mask, which ends with a false positive.
+	 */
+	smp_mb();
 	if (cpumask_empty(&wd_smp_cpus_pending)) {
 		unsigned long flags;
 
+none_pending:
+		/*
+		 * Double check under lock because more than one CPU could see
+		 * a clear mask with the lockless check after clearing their
+		 * pending bits.
+		 */
 		wd_smp_lock(&flags);
 		if (cpumask_empty(&wd_smp_cpus_pending)) {
 			wd_smp_last_reset_tb = tb;
@@ -312,8 +353,12 @@
 {
 	unsigned long ticks = tb_ticks_per_usec * wd_timer_period_ms * 1000;
 	int cpu = smp_processor_id();
-	u64 tb = get_tb();
+	u64 tb;
 
+	if (!cpumask_test_cpu(cpu, &watchdog_cpumask))
+		return;
+
+	tb = get_tb();
 	if (tb - per_cpu(wd_timer_tb, cpu) >= ticks) {
 		per_cpu(wd_timer_tb, cpu) = tb;
 		wd_smp_clear_cpu_pending(cpu, tb);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kexec/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kexec/core.c
@@ -147,11 +147,18 @@
 	if (!crashk_res.start) {
 #ifdef CONFIG_PPC64
 		/*
-		 * On 64bit we split the RMO in half but cap it at half of
-		 * a small SLB (128MB) since the crash kernel needs to place
-		 * itself and some stacks to be in the first segment.
+		 * On the LPAR platform place the crash kernel to mid of
+		 * RMA size (512MB or more) to ensure the crash kernel
+		 * gets enough space to place itself and some stack to be
+		 * in the first segment. At the same time normal kernel
+		 * also get enough space to allocate memory for essential
+		 * system resource in the first segment. Keep the crash
+		 * kernel starts at 128MB offset on other platforms.
 		 */
-		crashk_res.start = min(0x8000000ULL, (ppc64_rma_size / 2));
+		if (firmware_has_feature(FW_FEATURE_LPAR))
+			crashk_res.start = ppc64_rma_size / 2;
+		else
+			crashk_res.start = min(0x8000000ULL, (ppc64_rma_size / 2));
 #else
 		crashk_res.start = KDUMP_KERNELBASE;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kexec/core_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kexec/core_64.c
@@ -26,6 +26,7 @@
 #include <asm/mmu.h>
 #include <asm/sections.h>	/* _end */
 #include <asm/prom.h>
+#include <asm/setup.h>
 #include <asm/smp.h>
 #include <asm/hw_breakpoint.h>
 #include <asm/asm-prototypes.h>
@@ -317,6 +318,16 @@
 	if (!kdump_in_progress())
 		kexec_prepare_cpus();
 
+#ifdef CONFIG_PPC_PSERIES
+	/*
+	 * This must be done after other CPUs have shut down, otherwise they
+	 * could execute the 'scv' instruction, which is not supported with
+	 * reloc disabled (see configure_exceptions()).
+	 */
+	if (firmware_has_feature(FW_FEATURE_SET_MODE))
+		pseries_disable_reloc_on_exc();
+#endif
+
 	printk("kexec: Starting switchover sequence.\n");
 
 	/* switch to a staticly allocated stack.  Based on irq stack code.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kexec/file_load_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kexec/file_load_64.c
@@ -909,13 +909,18 @@
 	if (dn) {
 		u64 val;
 
-		of_property_read_u64(dn, "opal-base-address", &val);
+		ret = of_property_read_u64(dn, "opal-base-address", &val);
+		if (ret)
+			goto out;
+
 		ret = kexec_purgatory_get_set_symbol(image, "opal_base", &val,
 						     sizeof(val), false);
 		if (ret)
 			goto out;
 
-		of_property_read_u64(dn, "opal-entry-address", &val);
+		ret = of_property_read_u64(dn, "opal-entry-address", &val);
+		if (ret)
+			goto out;
 		ret = kexec_purgatory_get_set_symbol(image, "opal_entry", &val,
 						     sizeof(val), false);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_32_sr.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_32_sr.S
@@ -122,11 +122,27 @@
 
 	/* 0x0 - 0xb */
 
-	/* 'current->mm' needs to be in r4 */
-	tophys(r4, r2)
-	lwz	r4, MM(r4)
-	tophys(r4, r4)
-	/* This only clobbers r0, r3, r4 and r5 */
+	/* switch_mmu_context() needs paging, let's enable it */
+	mfmsr   r9
+	ori     r11, r9, MSR_DR
+	mtmsr   r11
+	sync
+
+	/* switch_mmu_context() clobbers r12, rescue it */
+	SAVE_GPR(12, r1)
+
+	/* Calling switch_mmu_context(<inv>, current->mm, <inv>); */
+	lwz	r4, MM(r2)
 	bl	switch_mmu_context
 
+	/* restore r12 */
+	REST_GPR(12, r1)
+
+	/* Disable paging again */
+	mfmsr   r9
+	li      r6, MSR_DR
+	andc    r9, r9, r6
+	mtmsr	r9
+	sync
+
 .endm
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_64_entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_64_entry.S
@@ -407,10 +407,16 @@
 	 */
 	ld	r10,HSTATE_SCRATCH0(r13)
 	cmpwi	r10,BOOK3S_INTERRUPT_MACHINE_CHECK
-	beq	machine_check_common
+	beq	.Lcall_machine_check_common
 
 	cmpwi	r10,BOOK3S_INTERRUPT_SYSTEM_RESET
-	beq	system_reset_common
+	beq	.Lcall_system_reset_common
 
 	b	.
+
+.Lcall_machine_check_common:
+	b	machine_check_common
+
+.Lcall_system_reset_common:
+	b	system_reset_common
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_64_vio.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_64_vio.c
@@ -117,14 +117,16 @@
 	}
 	rcu_read_unlock();
 
-	fdput(f);
-
-	if (!found)
+	if (!found) {
+		fdput(f);
 		return -EINVAL;
+	}
 
 	table_group = iommu_group_get_iommudata(grp);
-	if (WARN_ON(!table_group))
+	if (WARN_ON(!table_group)) {
+		fdput(f);
 		return -EFAULT;
+	}
 
 	for (i = 0; i < IOMMU_TABLE_GROUP_MAX_TABLES; ++i) {
 		struct iommu_table *tbltmp = table_group->tables[i];
@@ -145,8 +147,10 @@
 			break;
 		}
 	}
-	if (!tbl)
+	if (!tbl) {
+		fdput(f);
 		return -EINVAL;
+	}
 
 	rcu_read_lock();
 	list_for_each_entry_rcu(stit, &stt->iommu_tables, next) {
@@ -157,6 +161,7 @@
 			/* stit is being destroyed */
 			iommu_tce_table_put(tbl);
 			rcu_read_unlock();
+			fdput(f);
 			return -ENOTTY;
 		}
 		/*
@@ -164,6 +169,7 @@
 		 * its KVM reference counter and can return.
 		 */
 		rcu_read_unlock();
+		fdput(f);
 		return 0;
 	}
 	rcu_read_unlock();
@@ -171,6 +177,7 @@
 	stit = kzalloc(sizeof(*stit), GFP_KERNEL);
 	if (!stit) {
 		iommu_tce_table_put(tbl);
+		fdput(f);
 		return -ENOMEM;
 	}
 
@@ -179,6 +186,7 @@
 
 	list_add_rcu(&stit->next, &stt->iommu_tables);
 
+	fdput(f);
 	return 0;
 }
 
@@ -421,13 +429,19 @@
 	tbl[idx % TCES_PER_PAGE] = tce;
 }
 
-static void kvmppc_clear_tce(struct mm_struct *mm, struct iommu_table *tbl,
-		unsigned long entry)
+static void kvmppc_clear_tce(struct mm_struct *mm, struct kvmppc_spapr_tce_table *stt,
+		struct iommu_table *tbl, unsigned long entry)
 {
-	unsigned long hpa = 0;
-	enum dma_data_direction dir = DMA_NONE;
+	unsigned long i;
+	unsigned long subpages = 1ULL << (stt->page_shift - tbl->it_page_shift);
+	unsigned long io_entry = entry << (stt->page_shift - tbl->it_page_shift);
 
-	iommu_tce_xchg_no_kill(mm, tbl, entry, &hpa, &dir);
+	for (i = 0; i < subpages; ++i) {
+		unsigned long hpa = 0;
+		enum dma_data_direction dir = DMA_NONE;
+
+		iommu_tce_xchg_no_kill(mm, tbl, io_entry + i, &hpa, &dir);
+	}
 }
 
 static long kvmppc_tce_iommu_mapped_dec(struct kvm *kvm,
@@ -486,6 +500,8 @@
 			break;
 	}
 
+	iommu_tce_kill(tbl, io_entry, subpages);
+
 	return ret;
 }
 
@@ -545,6 +561,8 @@
 			break;
 	}
 
+	iommu_tce_kill(tbl, io_entry, subpages);
+
 	return ret;
 }
 
@@ -591,10 +609,9 @@
 			ret = kvmppc_tce_iommu_map(vcpu->kvm, stt, stit->tbl,
 					entry, ua, dir);
 
-		iommu_tce_kill(stit->tbl, entry, 1);
 
 		if (ret != H_SUCCESS) {
-			kvmppc_clear_tce(vcpu->kvm->mm, stit->tbl, entry);
+			kvmppc_clear_tce(vcpu->kvm->mm, stt, stit->tbl, entry);
 			goto unlock_exit;
 		}
 	}
@@ -670,13 +687,13 @@
 		 */
 		if (get_user(tce, tces + i)) {
 			ret = H_TOO_HARD;
-			goto invalidate_exit;
+			goto unlock_exit;
 		}
 		tce = be64_to_cpu(tce);
 
 		if (kvmppc_tce_to_ua(vcpu->kvm, tce, &ua)) {
 			ret = H_PARAMETER;
-			goto invalidate_exit;
+			goto unlock_exit;
 		}
 
 		list_for_each_entry_lockless(stit, &stt->iommu_tables, next) {
@@ -685,19 +702,15 @@
 					iommu_tce_direction(tce));
 
 			if (ret != H_SUCCESS) {
-				kvmppc_clear_tce(vcpu->kvm->mm, stit->tbl,
-						entry);
-				goto invalidate_exit;
+				kvmppc_clear_tce(vcpu->kvm->mm, stt, stit->tbl,
+						 entry + i);
+				goto unlock_exit;
 			}
 		}
 
 		kvmppc_tce_put(stt, entry + i, tce);
 	}
 
-invalidate_exit:
-	list_for_each_entry_lockless(stit, &stt->iommu_tables, next)
-		iommu_tce_kill(stit->tbl, entry, npages);
-
 unlock_exit:
 	srcu_read_unlock(&vcpu->kvm->srcu, idx);
 
@@ -736,20 +749,16 @@
 				continue;
 
 			if (ret == H_TOO_HARD)
-				goto invalidate_exit;
+				return ret;
 
 			WARN_ON_ONCE(1);
-			kvmppc_clear_tce(vcpu->kvm->mm, stit->tbl, entry);
+			kvmppc_clear_tce(vcpu->kvm->mm, stt, stit->tbl, entry + i);
 		}
 	}
 
 	for (i = 0; i < npages; ++i, ioba += (1ULL << stt->page_shift))
 		kvmppc_tce_put(stt, ioba >> stt->page_shift, tce_value);
 
-invalidate_exit:
-	list_for_each_entry_lockless(stit, &stt->iommu_tables, next)
-		iommu_tce_kill(stit->tbl, ioba >> stt->page_shift, npages);
-
 	return ret;
 }
 EXPORT_SYMBOL_GPL(kvmppc_h_stuff_tce);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_64_vio_hv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_64_vio_hv.c
@@ -247,13 +247,19 @@
 		tbl->it_ops->tce_kill(tbl, entry, pages, true);
 }
 
-static void kvmppc_rm_clear_tce(struct kvm *kvm, struct iommu_table *tbl,
-		unsigned long entry)
+static void kvmppc_rm_clear_tce(struct kvm *kvm, struct kvmppc_spapr_tce_table *stt,
+		struct iommu_table *tbl, unsigned long entry)
 {
-	unsigned long hpa = 0;
-	enum dma_data_direction dir = DMA_NONE;
+	unsigned long i;
+	unsigned long subpages = 1ULL << (stt->page_shift - tbl->it_page_shift);
+	unsigned long io_entry = entry << (stt->page_shift - tbl->it_page_shift);
+
+	for (i = 0; i < subpages; ++i) {
+		unsigned long hpa = 0;
+		enum dma_data_direction dir = DMA_NONE;
 
-	iommu_tce_xchg_no_kill_rm(kvm->mm, tbl, entry, &hpa, &dir);
+		iommu_tce_xchg_no_kill_rm(kvm->mm, tbl, io_entry + i, &hpa, &dir);
+	}
 }
 
 static long kvmppc_rm_tce_iommu_mapped_dec(struct kvm *kvm,
@@ -316,6 +322,8 @@
 			break;
 	}
 
+	iommu_tce_kill_rm(tbl, io_entry, subpages);
+
 	return ret;
 }
 
@@ -379,6 +387,8 @@
 			break;
 	}
 
+	iommu_tce_kill_rm(tbl, io_entry, subpages);
+
 	return ret;
 }
 
@@ -420,10 +430,8 @@
 			ret = kvmppc_rm_tce_iommu_map(vcpu->kvm, stt,
 					stit->tbl, entry, ua, dir);
 
-		iommu_tce_kill_rm(stit->tbl, entry, 1);
-
 		if (ret != H_SUCCESS) {
-			kvmppc_rm_clear_tce(vcpu->kvm, stit->tbl, entry);
+			kvmppc_rm_clear_tce(vcpu->kvm, stt, stit->tbl, entry);
 			return ret;
 		}
 	}
@@ -561,7 +569,7 @@
 		ua = 0;
 		if (kvmppc_rm_tce_to_ua(vcpu->kvm, tce, &ua)) {
 			ret = H_PARAMETER;
-			goto invalidate_exit;
+			goto unlock_exit;
 		}
 
 		list_for_each_entry_lockless(stit, &stt->iommu_tables, next) {
@@ -570,19 +578,15 @@
 					iommu_tce_direction(tce));
 
 			if (ret != H_SUCCESS) {
-				kvmppc_rm_clear_tce(vcpu->kvm, stit->tbl,
-						entry);
-				goto invalidate_exit;
+				kvmppc_rm_clear_tce(vcpu->kvm, stt, stit->tbl,
+						entry + i);
+				goto unlock_exit;
 			}
 		}
 
 		kvmppc_rm_tce_put(stt, entry + i, tce);
 	}
 
-invalidate_exit:
-	list_for_each_entry_lockless(stit, &stt->iommu_tables, next)
-		iommu_tce_kill_rm(stit->tbl, entry, npages);
-
 unlock_exit:
 	if (!prereg)
 		arch_spin_unlock(&kvm->mmu_lock.rlock.raw_lock);
@@ -620,20 +624,16 @@
 				continue;
 
 			if (ret == H_TOO_HARD)
-				goto invalidate_exit;
+				return ret;
 
 			WARN_ON_ONCE_RM(1);
-			kvmppc_rm_clear_tce(vcpu->kvm, stit->tbl, entry);
+			kvmppc_rm_clear_tce(vcpu->kvm, stt, stit->tbl, entry + i);
 		}
 	}
 
 	for (i = 0; i < npages; ++i, ioba += (1ULL << stt->page_shift))
 		kvmppc_rm_tce_put(stt, ioba >> stt->page_shift, tce_value);
 
-invalidate_exit:
-	list_for_each_entry_lockless(stit, &stt->iommu_tables, next)
-		iommu_tce_kill_rm(stit->tbl, ioba >> stt->page_shift, npages);
-
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv.c
@@ -1731,7 +1731,6 @@
 
 static int kvmppc_handle_nested_exit(struct kvm_vcpu *vcpu)
 {
-	struct kvm_nested_guest *nested = vcpu->arch.nested;
 	int r;
 	int srcu_idx;
 
@@ -1831,7 +1830,7 @@
 		 * it into a HEAI.
 		 */
 		if (!(vcpu->arch.hfscr_permitted & (1UL << cause)) ||
-					(nested->hfscr & (1UL << cause))) {
+				(vcpu->arch.nested_hfscr & (1UL << cause))) {
 			vcpu->arch.trap = BOOK3S_INTERRUPT_H_EMUL_ASSIST;
 
 			/*
@@ -3726,7 +3725,20 @@
 
 	kvmppc_set_host_core(pcpu);
 
-	guest_exit_irqoff();
+	context_tracking_guest_exit();
+	if (!vtime_accounting_enabled_this_cpu()) {
+		local_irq_enable();
+		/*
+		 * Service IRQs here before vtime_account_guest_exit() so any
+		 * ticks that occurred while running the guest are accounted to
+		 * the guest. If vtime accounting is enabled, accounting uses
+		 * TB rather than ticks, so it can be done without enabling
+		 * interrupts here, which has the problem that it accounts
+		 * interrupt processing overhead to the host.
+		 */
+		local_irq_disable();
+	}
+	vtime_account_guest_exit();
 
 	local_irq_enable();
 
@@ -4510,7 +4522,20 @@
 
 	kvmppc_set_host_core(pcpu);
 
-	guest_exit_irqoff();
+	context_tracking_guest_exit();
+	if (!vtime_accounting_enabled_this_cpu()) {
+		local_irq_enable();
+		/*
+		 * Service IRQs here before vtime_account_guest_exit() so any
+		 * ticks that occurred while running the guest are accounted to
+		 * the guest. If vtime accounting is enabled, accounting uses
+		 * TB rather than ticks, so it can be done without enabling
+		 * interrupts here, which has the problem that it accounts
+		 * interrupt processing overhead to the host.
+		 */
+		local_irq_disable();
+	}
+	vtime_account_guest_exit();
 
 	local_irq_enable();
 
@@ -4835,8 +4860,12 @@
 	unsigned long npages = mem->memory_size >> PAGE_SHIFT;
 
 	if (change == KVM_MR_CREATE) {
-		slot->arch.rmap = vzalloc(array_size(npages,
-					  sizeof(*slot->arch.rmap)));
+		unsigned long size = array_size(npages, sizeof(*slot->arch.rmap));
+
+		if ((size >> PAGE_SHIFT) > totalram_pages())
+			return -ENOMEM;
+
+		slot->arch.rmap = vzalloc(size);
 		if (!slot->arch.rmap)
 			return -ENOMEM;
 	}
@@ -5206,6 +5235,10 @@
 		kvm->arch.host_lpcr = lpcr = mfspr(SPRN_LPCR);
 		lpcr &= LPCR_PECE | LPCR_LPES;
 	} else {
+		/*
+		 * The L2 LPES mode will be set by the L0 according to whether
+		 * or not it needs to take external interrupts in HV mode.
+		 */
 		lpcr = 0;
 	}
 	lpcr |= (4UL << LPCR_DPFD_SH) | LPCR_HDICE |
@@ -6072,8 +6105,11 @@
 	if (r)
 		return r;
 
-	if (kvmppc_radix_possible())
+	if (kvmppc_radix_possible()) {
 		r = kvmppc_radix_init();
+		if (r)
+			return r;
+	}
 
 	r = kvmppc_uvmem_init();
 	if (r < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv_builtin.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv_builtin.c
@@ -20,7 +20,7 @@
 #include <asm/interrupt.h>
 #include <asm/kvm_ppc.h>
 #include <asm/kvm_book3s.h>
-#include <asm/archrandom.h>
+#include <asm/machdep.h>
 #include <asm/xics.h>
 #include <asm/xive.h>
 #include <asm/dbell.h>
@@ -177,13 +177,14 @@
 
 int kvmppc_hwrng_present(void)
 {
-	return powernv_hwrng_present();
+	return ppc_md.get_random_seed != NULL;
 }
 EXPORT_SYMBOL_GPL(kvmppc_hwrng_present);
 
 long kvmppc_rm_h_random(struct kvm_vcpu *vcpu)
 {
-	if (powernv_get_random_real_mode(&vcpu->arch.regs.gpr[4]))
+	if (ppc_md.get_random_seed &&
+	    ppc_md.get_random_seed(&vcpu->arch.regs.gpr[4]))
 		return H_SUCCESS;
 
 	return H_HARDWARE;
@@ -695,6 +696,7 @@
 				       "r" (0) : "memory");
 		}
 		asm volatile("ptesync": : :"memory");
+		// POWER9 congruence-class TLBIEL leaves ERAT. Flush it now.
 		asm volatile(PPC_RADIX_INVALIDATE_ERAT_GUEST : : :"memory");
 	} else {
 		for (set = 0; set < kvm->arch.tlb_sets; ++set) {
@@ -705,7 +707,9 @@
 			rb += PPC_BIT(51);	/* increment set number */
 		}
 		asm volatile("ptesync": : :"memory");
-		asm volatile(PPC_ISA_3_0_INVALIDATE_ERAT : : :"memory");
+		// POWER9 congruence-class TLBIEL leaves ERAT. Flush it now.
+		if (cpu_has_feature(CPU_FTR_ARCH_300))
+			asm volatile(PPC_ISA_3_0_INVALIDATE_ERAT : : :"memory");
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv_nested.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv_nested.c
@@ -261,8 +261,7 @@
 	/*
 	 * Don't let L1 change LPCR bits for the L2 except these:
 	 */
-	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC | LPCR_AIL | LPCR_LD |
-		LPCR_LPES | LPCR_MER;
+	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC | LPCR_AIL | LPCR_LD | LPCR_MER;
 
 	/*
 	 * Additional filtering is required depending on hardware
@@ -362,7 +361,7 @@
 	/* set L1 state to L2 state */
 	vcpu->arch.nested = l2;
 	vcpu->arch.nested_vcpu_id = l2_hv.vcpu_token;
-	l2->hfscr = l2_hv.hfscr;
+	vcpu->arch.nested_hfscr = l2_hv.hfscr;
 	vcpu->arch.regs = l2_regs;
 
 	/* Guest must always run with ME enabled, HV disabled. */
@@ -582,7 +581,7 @@
 	if (eaddr & (0xFFFUL << 52))
 		return H_PARAMETER;
 
-	buf = kzalloc(n, GFP_KERNEL);
+	buf = kzalloc(n, GFP_KERNEL | __GFP_NOWARN);
 	if (!buf)
 		return H_NO_MEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv_p9_entry.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv_p9_entry.c
@@ -7,15 +7,6 @@
 #include <asm/ppc-opcode.h>
 
 #ifdef CONFIG_KVM_BOOK3S_HV_EXIT_TIMING
-static void __start_timing(struct kvm_vcpu *vcpu, struct kvmhv_tb_accumulator *next)
-{
-	struct kvmppc_vcore *vc = vcpu->arch.vcore;
-	u64 tb = mftb() - vc->tb_offset_applied;
-
-	vcpu->arch.cur_activity = next;
-	vcpu->arch.cur_tb_start = tb;
-}
-
 static void __accumulate_time(struct kvm_vcpu *vcpu, struct kvmhv_tb_accumulator *next)
 {
 	struct kvmppc_vcore *vc = vcpu->arch.vcore;
@@ -47,8 +38,8 @@
 	curr->seqcount = seq + 2;
 }
 
-#define start_timing(vcpu, next) __start_timing(vcpu, next)
-#define end_timing(vcpu) __start_timing(vcpu, NULL)
+#define start_timing(vcpu, next) __accumulate_time(vcpu, next)
+#define end_timing(vcpu) __accumulate_time(vcpu, NULL)
 #define accumulate_time(vcpu, next) __accumulate_time(vcpu, next)
 #else
 #define start_timing(vcpu, next) do {} while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv_ras.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv_ras.c
@@ -9,6 +9,7 @@
 #include <linux/kvm.h>
 #include <linux/kvm_host.h>
 #include <linux/kernel.h>
+#include <asm/lppaca.h>
 #include <asm/opal.h>
 #include <asm/mce.h>
 #include <asm/machdep.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv_rmhandlers.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv_rmhandlers.S
@@ -2005,7 +2005,7 @@
 	.globl	hcall_real_table_end
 hcall_real_table_end:
 
-_GLOBAL(kvmppc_h_set_xdabr)
+_GLOBAL_TOC(kvmppc_h_set_xdabr)
 EXPORT_SYMBOL_GPL(kvmppc_h_set_xdabr)
 	andi.	r0, r5, DABRX_USER | DABRX_KERNEL
 	beq	6f
@@ -2015,7 +2015,7 @@
 6:	li	r3, H_PARAMETER
 	blr
 
-_GLOBAL(kvmppc_h_set_dabr)
+_GLOBAL_TOC(kvmppc_h_set_dabr)
 EXPORT_SYMBOL_GPL(kvmppc_h_set_dabr)
 	li	r5, DABRX_USER | DABRX_KERNEL
 3:
@@ -2711,8 +2711,7 @@
 	std	r0, GPR0(r1)
 	std	r9, GPR1(r1)
 	std	r2, GPR2(r1)
-	SAVE_4GPRS(3, r1)
-	SAVE_2GPRS(7, r1)
+	SAVE_GPRS(3, 8, r1)
 	srdi	r0, r12, 32
 	clrldi	r12, r12, 32
 	std	r0, _CCR(r1)
@@ -2735,7 +2734,7 @@
 	ld	r9, HSTATE_SCRATCH2(r13)
 	ld	r12, HSTATE_SCRATCH0(r13)
 	GET_SCRATCH0(r0)
-	SAVE_4GPRS(9, r1)
+	SAVE_GPRS(9, 12, r1)
 	std	r0, GPR13(r1)
 	SAVE_NVGPRS(r1)
 	ld	r5, HSTATE_CFAR(r13)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/book3s_hv_uvmem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/book3s_hv_uvmem.c
@@ -251,7 +251,7 @@
 	p = kzalloc(sizeof(*p), GFP_KERNEL);
 	if (!p)
 		return -ENOMEM;
-	p->pfns = vzalloc(array_size(slot->npages, sizeof(*p->pfns)));
+	p->pfns = vcalloc(slot->npages, sizeof(*p->pfns));
 	if (!p->pfns) {
 		kfree(p);
 		return -ENOMEM;
@@ -360,13 +360,15 @@
 static bool kvmppc_next_nontransitioned_gfn(const struct kvm_memory_slot *memslot,
 		struct kvm *kvm, unsigned long *gfn)
 {
-	struct kvmppc_uvmem_slot *p;
+	struct kvmppc_uvmem_slot *p = NULL, *iter;
 	bool ret = false;
 	unsigned long i;
 
-	list_for_each_entry(p, &kvm->arch.uvmem_pfns, list)
-		if (*gfn >= p->base_pfn && *gfn < p->base_pfn + p->nr_pfns)
+	list_for_each_entry(iter, &kvm->arch.uvmem_pfns, list)
+		if (*gfn >= iter->base_pfn && *gfn < iter->base_pfn + iter->nr_pfns) {
+			p = iter;
 			break;
+		}
 	if (!p)
 		return ret;
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/booke.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/booke.c
@@ -1042,7 +1042,21 @@
 	}
 
 	trace_kvm_exit(exit_nr, vcpu);
-	guest_exit_irqoff();
+
+	context_tracking_guest_exit();
+	if (!vtime_accounting_enabled_this_cpu()) {
+		local_irq_enable();
+		/*
+		 * Service IRQs here before vtime_account_guest_exit() so any
+		 * ticks that occurred while running the guest are accounted to
+		 * the guest. If vtime accounting is enabled, accounting uses
+		 * TB rather than ticks, so it can be done without enabling
+		 * interrupts here, which has the problem that it accounts
+		 * interrupt processing overhead to the host.
+		 */
+		local_irq_disable();
+	}
+	vtime_account_guest_exit();
 
 	local_irq_enable();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/kvm/powerpc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/kvm/powerpc.c
@@ -1507,7 +1507,7 @@
 {
 	enum emulation_result emulated = EMULATE_DONE;
 
-	if (vcpu->arch.mmio_vsx_copy_nums > 2)
+	if (vcpu->arch.mmio_vmx_copy_nums > 2)
 		return EMULATE_FAIL;
 
 	while (vcpu->arch.mmio_vmx_copy_nums) {
@@ -1604,7 +1604,7 @@
 	unsigned int index = rs & KVM_MMIO_REG_MASK;
 	enum emulation_result emulated = EMULATE_DONE;
 
-	if (vcpu->arch.mmio_vsx_copy_nums > 2)
+	if (vcpu->arch.mmio_vmx_copy_nums > 2)
 		return EMULATE_FAIL;
 
 	vcpu->arch.io_gpr = rs;
@@ -1963,8 +1963,10 @@
 			break;
 
 		r = -ENXIO;
-		if (!xive_enabled())
+		if (!xive_enabled()) {
+			fdput(f);
 			break;
+		}
 
 		r = -EPERM;
 		dev = kvm_device_from_filp(f.file);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/lib/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/lib/Makefile
@@ -19,6 +19,9 @@
 CFLAGS_feature-fixups.o += -DDISABLE_BRANCH_PROFILING
 endif
 
+CFLAGS_code-patching.o += $(DISABLE_LATENT_ENTROPY_PLUGIN)
+CFLAGS_feature-fixups.o += $(DISABLE_LATENT_ENTROPY_PLUGIN)
+
 obj-y += alloc.o code-patching.o feature-fixups.o pmem.o test_code-patching.o
 
 ifndef CONFIG_KASAN
@@ -34,8 +37,8 @@
 # 64-bit linker creates .sfpr on demand for final link (vmlinux),
 # so it is only needed for modules, and only for older linkers which
 # do not support --save-restore-funcs
-ifeq ($(call ld-ifversion, -lt, 22500, y),y)
-extra-$(CONFIG_PPC64)	+= crtsavres.o
+ifndef CONFIG_LD_IS_BFD
+always-$(CONFIG_PPC64)	+= crtsavres.o
 endif
 
 obj-$(CONFIG_PPC_BOOK3S_64) += copyuser_power7.o copypage_power7.o \
@@ -64,6 +67,6 @@
 obj-$(CONFIG_FTR_FIXUP_SELFTEST) += feature-fixups-test.o
 
 obj-$(CONFIG_ALTIVEC)	+= xor_vmx.o xor_vmx_glue.o
-CFLAGS_xor_vmx.o += -maltivec $(call cc-option,-mabi=altivec)
+CFLAGS_xor_vmx.o += -mhard-float -maltivec $(call cc-option,-mabi=altivec)
 
 obj-$(CONFIG_PPC64) += $(obj64-y)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/lib/code-patching.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/lib/code-patching.c
@@ -51,7 +51,7 @@
 {
 	struct vm_struct *area;
 
-	area = get_vm_area(PAGE_SIZE, VM_ALLOC);
+	area = get_vm_area(PAGE_SIZE, 0);
 	if (!area) {
 		WARN_ONCE(1, "Failed to create text area for cpu %d\n",
 			cpu);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/lib/feature-fixups.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/lib/feature-fixups.c
@@ -228,6 +228,7 @@
 
 static bool stf_exit_reentrant = false;
 static bool rfi_exit_reentrant = false;
+static DEFINE_MUTEX(exit_flush_lock);
 
 static int __do_stf_barrier_fixups(void *data)
 {
@@ -253,6 +254,9 @@
 	 * low level interrupt exit code before patching. After the patching,
 	 * if allowed, then flip the branch to allow fast exits.
 	 */
+
+	// Prevent static key update races with do_rfi_flush_fixups()
+	mutex_lock(&exit_flush_lock);
 	static_branch_enable(&interrupt_exit_not_reentrant);
 
 	stop_machine(__do_stf_barrier_fixups, &types, NULL);
@@ -264,6 +268,8 @@
 
 	if (stf_exit_reentrant && rfi_exit_reentrant)
 		static_branch_disable(&interrupt_exit_not_reentrant);
+
+	mutex_unlock(&exit_flush_lock);
 }
 
 void do_uaccess_flush_fixups(enum l1d_flush_type types)
@@ -486,6 +492,9 @@
 	 * without stop_machine, so this could be achieved with a broadcast
 	 * IPI instead, but this matches the stf sequence.
 	 */
+
+	// Prevent static key update races with do_stf_barrier_fixups()
+	mutex_lock(&exit_flush_lock);
 	static_branch_enable(&interrupt_exit_not_reentrant);
 
 	stop_machine(__do_rfi_flush_fixups, &types, NULL);
@@ -497,6 +506,8 @@
 
 	if (stf_exit_reentrant && rfi_exit_reentrant)
 		static_branch_disable(&interrupt_exit_not_reentrant);
+
+	mutex_unlock(&exit_flush_lock);
 }
 
 void do_barrier_nospec_fixups_range(bool enable, void *fixup_start, void *fixup_end)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/lib/sstep.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/lib/sstep.c
@@ -8,6 +8,7 @@
 #include <linux/kprobes.h>
 #include <linux/ptrace.h>
 #include <linux/prefetch.h>
+#include <asm/cpu_has_feature.h>
 #include <asm/sstep.h>
 #include <asm/processor.h>
 #include <linux/uaccess.h>
@@ -112,9 +113,9 @@
 {
 	if (!user_mode(regs))
 		return 1;
-	if (__access_ok(ea, nb))
+	if (access_ok((void __user *)ea, nb))
 		return 1;
-	if (__access_ok(ea, 1))
+	if (access_ok((void __user *)ea, 1))
 		/* Access overlaps the end of the user region */
 		regs->dar = TASK_SIZE_MAX - 1;
 	else
@@ -529,6 +530,8 @@
 	} u;
 
 	nb = GETSIZE(op->type);
+	if (nb > sizeof(u))
+		return -EINVAL;
 	if (!address_ok(regs, ea, nb))
 		return -EFAULT;
 	rn = op->reg;
@@ -579,6 +582,8 @@
 	} u;
 
 	nb = GETSIZE(op->type);
+	if (nb > sizeof(u))
+		return -EINVAL;
 	if (!address_ok(regs, ea, nb))
 		return -EFAULT;
 	rn = op->reg;
@@ -623,6 +628,9 @@
 		u8 b[sizeof(__vector128)];
 	} u = {};
 
+	if (size > sizeof(u))
+		return -EINVAL;
+
 	if (!address_ok(regs, ea & ~0xfUL, 16))
 		return -EFAULT;
 	/* align to multiple of size */
@@ -650,6 +658,9 @@
 		u8 b[sizeof(__vector128)];
 	} u;
 
+	if (size > sizeof(u))
+		return -EINVAL;
+
 	if (!address_ok(regs, ea & ~0xfUL, 16))
 		return -EFAULT;
 	/* align to multiple of size */
@@ -713,8 +724,8 @@
 #endif /* __powerpc64 */
 
 #ifdef CONFIG_VSX
-void emulate_vsx_load(struct instruction_op *op, union vsx_reg *reg,
-		      const void *mem, bool rev)
+static nokprobe_inline void emulate_vsx_load(struct instruction_op *op, union vsx_reg *reg,
+					     const void *mem, bool rev)
 {
 	int size, read_size;
 	int i, j;
@@ -796,11 +807,9 @@
 		break;
 	}
 }
-EXPORT_SYMBOL_GPL(emulate_vsx_load);
-NOKPROBE_SYMBOL(emulate_vsx_load);
 
-void emulate_vsx_store(struct instruction_op *op, const union vsx_reg *reg,
-		       void *mem, bool rev)
+static nokprobe_inline void emulate_vsx_store(struct instruction_op *op, const union vsx_reg *reg,
+					      void *mem, bool rev)
 {
 	int size, write_size;
 	int i, j;
@@ -888,8 +897,6 @@
 		break;
 	}
 }
-EXPORT_SYMBOL_GPL(emulate_vsx_store);
-NOKPROBE_SYMBOL(emulate_vsx_store);
 
 static nokprobe_inline int do_vsx_load(struct instruction_op *op,
 				       unsigned long ea, struct pt_regs *regs,
@@ -1014,7 +1021,10 @@
 
 #define __put_user_asmx(x, addr, err, op, cr)		\
 	__asm__ __volatile__(				\
+		".machine push\n"			\
+		".machine power8\n"			\
 		"1:	" op " %2,0,%3\n"		\
+		".machine pop\n"			\
 		"	mfcr	%1\n"			\
 		"2:\n"					\
 		".section .fixup,\"ax\"\n"		\
@@ -1027,7 +1037,10 @@
 
 #define __get_user_asmx(x, addr, err, op)		\
 	__asm__ __volatile__(				\
+		".machine push\n"			\
+		".machine power8\n"			\
 		"1:	"op" %1,0,%2\n"			\
+		".machine pop\n"			\
 		"2:\n"					\
 		".section .fixup,\"ax\"\n"		\
 		"3:	li	%0,%3\n"		\
@@ -3181,12 +3194,14 @@
 		case BARRIER_EIEIO:
 			eieio();
 			break;
+#ifdef CONFIG_PPC64
 		case BARRIER_LWSYNC:
 			asm volatile("lwsync" : : : "memory");
 			break;
 		case BARRIER_PTESYNC:
 			asm volatile("ptesync" : : : "memory");
 			break;
+#endif
 		}
 		break;
 
@@ -3304,7 +3319,7 @@
 			__put_user_asmx(op->val, ea, err, "stbcx.", cr);
 			break;
 		case 2:
-			__put_user_asmx(op->val, ea, err, "stbcx.", cr);
+			__put_user_asmx(op->val, ea, err, "sthcx.", cr);
 			break;
 #endif
 		case 4:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/lib/test_emulate_step_exec_instr.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/lib/test_emulate_step_exec_instr.S
@@ -37,7 +37,7 @@
 	 * The stack pointer (GPR1) and the thread pointer (GPR13) are not
 	 * saved as these should not be modified anyway.
 	 */
-	SAVE_2GPRS(2, r1)
+	SAVE_GPRS(2, 3, r1)
 	SAVE_NVGPRS(r1)
 
 	/*
@@ -75,8 +75,7 @@
 
 	/* Load GPRs from pt_regs */
 	REST_GPR(0, r31)
-	REST_10GPRS(2, r31)
-	REST_GPR(12, r31)
+	REST_GPRS(2, 12, r31)
 	REST_NVGPRS(r31)
 
 	/* Placeholder for the test instruction */
@@ -99,8 +98,7 @@
 	subi	r3, r3, GPR0
 	SAVE_GPR(0, r3)
 	SAVE_GPR(2, r3)
-	SAVE_8GPRS(4, r3)
-	SAVE_GPR(12, r3)
+	SAVE_GPRS(4, 12, r3)
 	SAVE_NVGPRS(r3)
 
 	/* Save resulting LR to pt_regs */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/math-emu/math_efp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/math-emu/math_efp.c
@@ -17,6 +17,7 @@
 
 #include <linux/types.h>
 #include <linux/prctl.h>
+#include <linux/module.h>
 
 #include <linux/uaccess.h>
 #include <asm/reg.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s32/kuep.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s32/kuep.c
@@ -3,18 +3,10 @@
 #include <asm/kup.h>
 #include <asm/smp.h>
 
-struct static_key_false disable_kuep_key;
-
 void setup_kuep(bool disabled)
 {
-	if (!disabled)
-		kuep_lock();
-
 	if (smp_processor_id() != boot_cpuid)
 		return;
 
-	if (disabled)
-		static_branch_enable(&disable_kuep_key);
-	else
-		pr_info("Activating Kernel Userspace Execution Prevention\n");
+	pr_info("Activating Kernel Userspace Execution Prevention\n");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s32/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s32/mmu.c
@@ -76,7 +76,7 @@
 	return 0;
 }
 
-static int find_free_bat(void)
+int __init find_free_bat(void)
 {
 	int b;
 	int n = mmu_has_feature(MMU_FTR_USE_HIGH_BATS) ? 8 : 4;
@@ -100,7 +100,7 @@
  * - block size has to be a power of two. This is calculated by finding the
  *   highest bit set to 1.
  */
-static unsigned int block_size(unsigned long base, unsigned long top)
+unsigned int bat_block_size(unsigned long base, unsigned long top)
 {
 	unsigned int max_size = SZ_256M;
 	unsigned int base_shift = (ffs(base) - 1) & 31;
@@ -145,7 +145,7 @@
 	int idx;
 
 	while ((idx = find_free_bat()) != -1 && base != top) {
-		unsigned int size = block_size(base, top);
+		unsigned int size = bat_block_size(base, top);
 
 		if (size < 128 << 10)
 			break;
@@ -159,10 +159,13 @@
 unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
 {
 	unsigned long done;
-	unsigned long border = (unsigned long)__init_begin - PAGE_OFFSET;
+	unsigned long border = (unsigned long)__srwx_boundary - PAGE_OFFSET;
+	unsigned long size;
 
+	size = roundup_pow_of_two((unsigned long)_einittext - PAGE_OFFSET);
+	setibat(0, PAGE_OFFSET, 0, size, PAGE_KERNEL_X);
 
-	if (debug_pagealloc_enabled_or_kfence() || __map_without_bats) {
+	if (debug_pagealloc_enabled_or_kfence()) {
 		pr_debug_once("Read-Write memory mapped without BATs\n");
 		if (base >= border)
 			return base;
@@ -196,18 +199,17 @@
 	int nb = mmu_has_feature(MMU_FTR_USE_HIGH_BATS) ? 8 : 4;
 	int i;
 	unsigned long base = (unsigned long)_stext - PAGE_OFFSET;
-	unsigned long top = (unsigned long)_etext - PAGE_OFFSET;
+	unsigned long top = ALIGN((unsigned long)_etext - PAGE_OFFSET, SZ_128K);
 	unsigned long border = (unsigned long)__init_begin - PAGE_OFFSET;
 	unsigned long size;
 
-	for (i = 0; i < nb - 1 && base < top && top - base > (128 << 10);) {
-		size = block_size(base, top);
+	for (i = 0; i < nb - 1 && base < top;) {
+		size = bat_block_size(base, top);
 		setibat(i++, PAGE_OFFSET + base, base, size, PAGE_KERNEL_TEXT);
 		base += size;
 	}
 	if (base < top) {
-		size = block_size(base, top);
-		size = max(size, 128UL << 10);
+		size = bat_block_size(base, top);
 		if ((top - base) > size) {
 			size <<= 1;
 			if (strict_kernel_rwx_enabled() && base + size > border)
@@ -247,10 +249,9 @@
 }
 
 /*
- * Set up one of the I/D BAT (block address translation) register pairs.
+ * Set up one of the D BAT (block address translation) register pairs.
  * The parameters are not checked; in particular size must be a power
  * of 2 between 128k and 256M.
- * On 603+, only set IBAT when _PAGE_EXEC is set
  */
 void __init setbat(int index, unsigned long virt, phys_addr_t phys,
 		   unsigned int size, pgprot_t prot)
@@ -286,10 +287,6 @@
 		/* G bit must be zero in IBATs */
 		flags &= ~_PAGE_EXEC;
 	}
-	if (flags & _PAGE_EXEC)
-		bat[0] = bat[1];
-	else
-		bat[0].batu = bat[0].batl = 0;
 
 	bat_addrs[index].start = virt;
 	bat_addrs[index].limit = virt + ((bl + 1) << 17) - 1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s64/hash_utils.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s64/hash_utils.c
@@ -1522,8 +1522,7 @@
 }
 EXPORT_SYMBOL_GPL(hash_page);
 
-DECLARE_INTERRUPT_HANDLER(__do_hash_fault);
-DEFINE_INTERRUPT_HANDLER(__do_hash_fault)
+DEFINE_INTERRUPT_HANDLER(do_hash_fault)
 {
 	unsigned long ea = regs->dar;
 	unsigned long dsisr = regs->dsisr;
@@ -1582,35 +1581,6 @@
 	}
 }
 
-/*
- * The _RAW interrupt entry checks for the in_nmi() case before
- * running the full handler.
- */
-DEFINE_INTERRUPT_HANDLER_RAW(do_hash_fault)
-{
-	/*
-	 * If we are in an "NMI" (e.g., an interrupt when soft-disabled), then
-	 * don't call hash_page, just fail the fault. This is required to
-	 * prevent re-entrancy problems in the hash code, namely perf
-	 * interrupts hitting while something holds H_PAGE_BUSY, and taking a
-	 * hash fault. See the comment in hash_preload().
-	 *
-	 * We come here as a result of a DSI at a point where we don't want
-	 * to call hash_page, such as when we are accessing memory (possibly
-	 * user memory) inside a PMU interrupt that occurred while interrupts
-	 * were soft-disabled.  We want to invoke the exception handler for
-	 * the access, or panic if there isn't a handler.
-	 */
-	if (unlikely(in_nmi())) {
-		do_bad_page_fault_segv(regs);
-		return 0;
-	}
-
-	__do_hash_fault(regs);
-
-	return 0;
-}
-
 #ifdef CONFIG_PPC_MM_SLICES
 static bool should_hash_preload(struct mm_struct *mm, unsigned long ea)
 {
@@ -1677,26 +1647,18 @@
 #endif /* CONFIG_PPC_64K_PAGES */
 
 	/*
-	 * __hash_page_* must run with interrupts off, as it sets the
-	 * H_PAGE_BUSY bit. It's possible for perf interrupts to hit at any
-	 * time and may take a hash fault reading the user stack, see
-	 * read_user_stack_slow() in the powerpc/perf code.
-	 *
-	 * If that takes a hash fault on the same page as we lock here, it
-	 * will bail out when seeing H_PAGE_BUSY set, and retry the access
-	 * leading to an infinite loop.
+	 * __hash_page_* must run with interrupts off, including PMI interrupts
+	 * off, as it sets the H_PAGE_BUSY bit.
 	 *
-	 * Disabling interrupts here does not prevent perf interrupts, but it
-	 * will prevent them taking hash faults (see the NMI test in
-	 * do_hash_page), then read_user_stack's copy_from_user_nofault will
-	 * fail and perf will fall back to read_user_stack_slow(), which
-	 * walks the Linux page tables.
+	 * It's otherwise possible for perf interrupts to hit at any time and
+	 * may take a hash fault reading the user stack, which could take a
+	 * hash miss and deadlock on the same H_PAGE_BUSY bit.
 	 *
 	 * Interrupts must also be off for the duration of the
 	 * mm_is_thread_local test and update, to prevent preempt running the
 	 * mm on another CPU (XXX: this may be racy vs kthread_use_mm).
 	 */
-	local_irq_save(flags);
+	powerpc_local_irq_pmu_save(flags);
 
 	/* Is that local to this CPU ? */
 	if (mm_is_thread_local(mm))
@@ -1721,7 +1683,7 @@
 				   mm_ctx_user_psize(&mm->context),
 				   pte_val(*ptep));
 
-	local_irq_restore(flags);
+	powerpc_local_irq_pmu_restore(flags);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s64/pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s64/pgtable.c
@@ -459,6 +459,7 @@
 	set_pte_at(vma->vm_mm, addr, ptep, pte);
 }
 
+#ifdef CONFIG_TRANSPARENT_HUGEPAGE
 /*
  * For hash translation mode, we use the deposited table to store hash slot
  * information and they are stored at PTRS_PER_PMD offset from related pmd
@@ -480,6 +481,7 @@
 
 	return true;
 }
+#endif
 
 /*
  * Does the CPU support tlbie?
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s64/radix_pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s64/radix_pgtable.c
@@ -232,6 +232,14 @@
 	end = (unsigned long)__init_begin;
 
 	radix__change_memory_range(start, end, _PAGE_WRITE);
+
+	for (start = PAGE_OFFSET; start < (unsigned long)_stext; start += PAGE_SIZE) {
+		end = start + PAGE_SIZE;
+		if (overlaps_interrupt_vector_text(start, end))
+			radix__change_memory_range(start, end, _PAGE_WRITE);
+		else
+			break;
+	}
 }
 
 void radix__mark_initmem_nx(void)
@@ -260,8 +268,24 @@
 static unsigned long next_boundary(unsigned long addr, unsigned long end)
 {
 #ifdef CONFIG_STRICT_KERNEL_RWX
-	if (addr < __pa_symbol(__init_begin))
-		return __pa_symbol(__init_begin);
+	unsigned long stext_phys;
+
+	stext_phys = __pa_symbol(_stext);
+
+	// Relocatable kernel running at non-zero real address
+	if (stext_phys != 0) {
+		// The end of interrupts code at zero is a rodata boundary
+		unsigned long end_intr = __pa_symbol(__end_interrupts) - stext_phys;
+		if (addr < end_intr)
+			return end_intr;
+
+		// Start of relocated kernel text is a rodata boundary
+		if (addr < stext_phys)
+			return stext_phys;
+	}
+
+	if (addr < __pa_symbol(__srwx_boundary))
+		return __pa_symbol(__srwx_boundary);
 #endif
 	return end;
 }
@@ -740,9 +764,9 @@
 }
 
 static void remove_pte_table(pte_t *pte_start, unsigned long addr,
-			     unsigned long end)
+			     unsigned long end, bool direct)
 {
-	unsigned long next;
+	unsigned long next, pages = 0;
 	pte_t *pte;
 
 	pte = pte_start + pte_index(addr);
@@ -764,13 +788,16 @@
 		}
 
 		pte_clear(&init_mm, addr, pte);
+		pages++;
 	}
+	if (direct)
+		update_page_count(mmu_virtual_psize, -pages);
 }
 
 static void __meminit remove_pmd_table(pmd_t *pmd_start, unsigned long addr,
-			     unsigned long end)
+				       unsigned long end, bool direct)
 {
-	unsigned long next;
+	unsigned long next, pages = 0;
 	pte_t *pte_base;
 	pmd_t *pmd;
 
@@ -788,19 +815,22 @@
 				continue;
 			}
 			pte_clear(&init_mm, addr, (pte_t *)pmd);
+			pages++;
 			continue;
 		}
 
 		pte_base = (pte_t *)pmd_page_vaddr(*pmd);
-		remove_pte_table(pte_base, addr, next);
+		remove_pte_table(pte_base, addr, next, direct);
 		free_pte_table(pte_base, pmd);
 	}
+	if (direct)
+		update_page_count(MMU_PAGE_2M, -pages);
 }
 
 static void __meminit remove_pud_table(pud_t *pud_start, unsigned long addr,
-			     unsigned long end)
+				       unsigned long end, bool direct)
 {
-	unsigned long next;
+	unsigned long next, pages = 0;
 	pmd_t *pmd_base;
 	pud_t *pud;
 
@@ -818,16 +848,20 @@
 				continue;
 			}
 			pte_clear(&init_mm, addr, (pte_t *)pud);
+			pages++;
 			continue;
 		}
 
 		pmd_base = pud_pgtable(*pud);
-		remove_pmd_table(pmd_base, addr, next);
+		remove_pmd_table(pmd_base, addr, next, direct);
 		free_pmd_table(pmd_base, pud);
 	}
+	if (direct)
+		update_page_count(MMU_PAGE_1G, -pages);
 }
 
-static void __meminit remove_pagetable(unsigned long start, unsigned long end)
+static void __meminit remove_pagetable(unsigned long start, unsigned long end,
+				       bool direct)
 {
 	unsigned long addr, next;
 	pud_t *pud_base;
@@ -856,7 +890,7 @@
 		}
 
 		pud_base = p4d_pgtable(*p4d);
-		remove_pud_table(pud_base, addr, next);
+		remove_pud_table(pud_base, addr, next, direct);
 		free_pud_table(pud_base, p4d);
 	}
 
@@ -879,7 +913,7 @@
 
 int __meminit radix__remove_section_mapping(unsigned long start, unsigned long end)
 {
-	remove_pagetable(start, end);
+	remove_pagetable(start, end, true);
 	return 0;
 }
 #endif /* CONFIG_MEMORY_HOTPLUG */
@@ -915,7 +949,7 @@
 #ifdef CONFIG_MEMORY_HOTPLUG
 void __meminit radix__vmemmap_remove_mapping(unsigned long start, unsigned long page_size)
 {
-	remove_pagetable(start, start + page_size);
+	remove_pagetable(start, start + page_size, false);
 }
 #endif
 #endif
@@ -954,15 +988,6 @@
 	pmd = *pmdp;
 	pmd_clear(pmdp);
 
-	/*
-	 * pmdp collapse_flush need to ensure that there are no parallel gup
-	 * walk after this call. This is needed so that we can have stable
-	 * page ref count when collapsing a page. We don't allow a collapse page
-	 * if we have gup taken on the page. We can ensure that by sending IPI
-	 * because gup walk happens with IRQ disabled.
-	 */
-	serialize_against_pte_lookup(vma->vm_mm);
-
 	radix__flush_tlb_collapsed_pmd(vma->vm_mm, address);
 
 	return pmd;
@@ -1030,8 +1055,8 @@
 				  pte_t entry, unsigned long address, int psize)
 {
 	struct mm_struct *mm = vma->vm_mm;
-	unsigned long set = pte_val(entry) & (_PAGE_DIRTY | _PAGE_ACCESSED |
-					      _PAGE_RW | _PAGE_EXEC);
+	unsigned long set = pte_val(entry) & (_PAGE_DIRTY | _PAGE_SOFT_DIRTY |
+					      _PAGE_ACCESSED | _PAGE_RW | _PAGE_EXEC);
 
 	unsigned long change = pte_val(entry) ^ pte_val(*ptep);
 	/*
@@ -1093,7 +1118,7 @@
 
 int pud_clear_huge(pud_t *pud)
 {
-	if (pud_huge(*pud)) {
+	if (pud_is_leaf(*pud)) {
 		pud_clear(pud);
 		return 1;
 	}
@@ -1140,7 +1165,7 @@
 
 int pmd_clear_huge(pmd_t *pmd)
 {
-	if (pmd_huge(*pmd)) {
+	if (pmd_is_leaf(*pmd)) {
 		pmd_clear(pmd);
 		return 1;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s64/radix_tlb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s64/radix_tlb.c
@@ -127,21 +127,6 @@
 	trace_tlbie(0, 0, rb, rs, ric, prs, r);
 }
 
-static __always_inline void __tlbie_pid_lpid(unsigned long pid,
-					     unsigned long lpid,
-					     unsigned long ric)
-{
-	unsigned long rb, rs, prs, r;
-
-	rb = PPC_BIT(53); /* IS = 1 */
-	rs = (pid << PPC_BITLSHIFT(31)) | (lpid & ~(PPC_BITMASK(0, 31)));
-	prs = 1; /* process scoped */
-	r = 1;   /* radix format */
-
-	asm volatile(PPC_TLBIE_5(%0, %4, %3, %2, %1)
-		     : : "r"(rb), "i"(r), "i"(prs), "i"(ric), "r"(rs) : "memory");
-	trace_tlbie(0, 0, rb, rs, ric, prs, r);
-}
 static __always_inline void __tlbie_lpid(unsigned long lpid, unsigned long ric)
 {
 	unsigned long rb,rs,prs,r;
@@ -202,23 +187,6 @@
 	trace_tlbie(0, 0, rb, rs, ric, prs, r);
 }
 
-static __always_inline void __tlbie_va_lpid(unsigned long va, unsigned long pid,
-					    unsigned long lpid,
-					    unsigned long ap, unsigned long ric)
-{
-	unsigned long rb, rs, prs, r;
-
-	rb = va & ~(PPC_BITMASK(52, 63));
-	rb |= ap << PPC_BITLSHIFT(58);
-	rs = (pid << PPC_BITLSHIFT(31)) | (lpid & ~(PPC_BITMASK(0, 31)));
-	prs = 1; /* process scoped */
-	r = 1;   /* radix format */
-
-	asm volatile(PPC_TLBIE_5(%0, %4, %3, %2, %1)
-		     : : "r"(rb), "i"(r), "i"(prs), "i"(ric), "r"(rs) : "memory");
-	trace_tlbie(0, 0, rb, rs, ric, prs, r);
-}
-
 static __always_inline void __tlbie_lpid_va(unsigned long va, unsigned long lpid,
 					    unsigned long ap, unsigned long ric)
 {
@@ -264,22 +232,6 @@
 	}
 }
 
-static inline void fixup_tlbie_va_range_lpid(unsigned long va,
-					     unsigned long pid,
-					     unsigned long lpid,
-					     unsigned long ap)
-{
-	if (cpu_has_feature(CPU_FTR_P9_TLBIE_ERAT_BUG)) {
-		asm volatile("ptesync" : : : "memory");
-		__tlbie_pid_lpid(0, lpid, RIC_FLUSH_TLB);
-	}
-
-	if (cpu_has_feature(CPU_FTR_P9_TLBIE_STQ_BUG)) {
-		asm volatile("ptesync" : : : "memory");
-		__tlbie_va_lpid(va, pid, lpid, ap, RIC_FLUSH_TLB);
-	}
-}
-
 static inline void fixup_tlbie_pid(unsigned long pid)
 {
 	/*
@@ -299,26 +251,6 @@
 	}
 }
 
-static inline void fixup_tlbie_pid_lpid(unsigned long pid, unsigned long lpid)
-{
-	/*
-	 * We can use any address for the invalidation, pick one which is
-	 * probably unused as an optimisation.
-	 */
-	unsigned long va = ((1UL << 52) - 1);
-
-	if (cpu_has_feature(CPU_FTR_P9_TLBIE_ERAT_BUG)) {
-		asm volatile("ptesync" : : : "memory");
-		__tlbie_pid_lpid(0, lpid, RIC_FLUSH_TLB);
-	}
-
-	if (cpu_has_feature(CPU_FTR_P9_TLBIE_STQ_BUG)) {
-		asm volatile("ptesync" : : : "memory");
-		__tlbie_va_lpid(va, pid, lpid, mmu_get_ap(MMU_PAGE_64K),
-				RIC_FLUSH_TLB);
-	}
-}
-
 static inline void fixup_tlbie_lpid_va(unsigned long va, unsigned long lpid,
 				       unsigned long ap)
 {
@@ -416,31 +348,6 @@
 	asm volatile("eieio; tlbsync; ptesync": : :"memory");
 }
 
-static inline void _tlbie_pid_lpid(unsigned long pid, unsigned long lpid,
-				   unsigned long ric)
-{
-	asm volatile("ptesync" : : : "memory");
-
-	/*
-	 * Workaround the fact that the "ric" argument to __tlbie_pid
-	 * must be a compile-time contraint to match the "i" constraint
-	 * in the asm statement.
-	 */
-	switch (ric) {
-	case RIC_FLUSH_TLB:
-		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_TLB);
-		fixup_tlbie_pid_lpid(pid, lpid);
-		break;
-	case RIC_FLUSH_PWC:
-		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_PWC);
-		break;
-	case RIC_FLUSH_ALL:
-	default:
-		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_ALL);
-		fixup_tlbie_pid_lpid(pid, lpid);
-	}
-	asm volatile("eieio; tlbsync; ptesync" : : : "memory");
-}
 struct tlbiel_pid {
 	unsigned long pid;
 	unsigned long ric;
@@ -566,20 +473,6 @@
 	fixup_tlbie_va_range(addr - page_size, pid, ap);
 }
 
-static inline void __tlbie_va_range_lpid(unsigned long start, unsigned long end,
-					 unsigned long pid, unsigned long lpid,
-					 unsigned long page_size,
-					 unsigned long psize)
-{
-	unsigned long addr;
-	unsigned long ap = mmu_get_ap(psize);
-
-	for (addr = start; addr < end; addr += page_size)
-		__tlbie_va_lpid(addr, pid, lpid, ap, RIC_FLUSH_TLB);
-
-	fixup_tlbie_va_range_lpid(addr - page_size, pid, lpid, ap);
-}
-
 static __always_inline void _tlbie_va(unsigned long va, unsigned long pid,
 				      unsigned long psize, unsigned long ric)
 {
@@ -660,18 +553,6 @@
 	asm volatile("eieio; tlbsync; ptesync": : :"memory");
 }
 
-static inline void _tlbie_va_range_lpid(unsigned long start, unsigned long end,
-					unsigned long pid, unsigned long lpid,
-					unsigned long page_size,
-					unsigned long psize, bool also_pwc)
-{
-	asm volatile("ptesync" : : : "memory");
-	if (also_pwc)
-		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_PWC);
-	__tlbie_va_range_lpid(start, end, pid, lpid, page_size, psize);
-	asm volatile("eieio; tlbsync; ptesync" : : : "memory");
-}
-
 static inline void _tlbiel_va_range_multicast(struct mm_struct *mm,
 				unsigned long start, unsigned long end,
 				unsigned long pid, unsigned long page_size,
@@ -1171,15 +1052,12 @@
 			}
 		}
 	} else {
-		bool hflush = false;
+		bool hflush;
 		unsigned long hstart, hend;
 
-		if (IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE)) {
-			hstart = (start + PMD_SIZE - 1) & PMD_MASK;
-			hend = end & PMD_MASK;
-			if (hstart < hend)
-				hflush = true;
-		}
+		hstart = (start + PMD_SIZE - 1) & PMD_MASK;
+		hend = end & PMD_MASK;
+		hflush = IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE) && hstart < hend;
 
 		if (type == FLUSH_TYPE_LOCAL) {
 			asm volatile("ptesync": : :"memory");
@@ -1471,6 +1349,127 @@
 }
 
 #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
+static __always_inline void __tlbie_pid_lpid(unsigned long pid,
+					     unsigned long lpid,
+					     unsigned long ric)
+{
+	unsigned long rb, rs, prs, r;
+
+	rb = PPC_BIT(53); /* IS = 1 */
+	rs = (pid << PPC_BITLSHIFT(31)) | (lpid & ~(PPC_BITMASK(0, 31)));
+	prs = 1; /* process scoped */
+	r = 1;   /* radix format */
+
+	asm volatile(PPC_TLBIE_5(%0, %4, %3, %2, %1)
+		     : : "r"(rb), "i"(r), "i"(prs), "i"(ric), "r"(rs) : "memory");
+	trace_tlbie(0, 0, rb, rs, ric, prs, r);
+}
+
+static __always_inline void __tlbie_va_lpid(unsigned long va, unsigned long pid,
+					    unsigned long lpid,
+					    unsigned long ap, unsigned long ric)
+{
+	unsigned long rb, rs, prs, r;
+
+	rb = va & ~(PPC_BITMASK(52, 63));
+	rb |= ap << PPC_BITLSHIFT(58);
+	rs = (pid << PPC_BITLSHIFT(31)) | (lpid & ~(PPC_BITMASK(0, 31)));
+	prs = 1; /* process scoped */
+	r = 1;   /* radix format */
+
+	asm volatile(PPC_TLBIE_5(%0, %4, %3, %2, %1)
+		     : : "r"(rb), "i"(r), "i"(prs), "i"(ric), "r"(rs) : "memory");
+	trace_tlbie(0, 0, rb, rs, ric, prs, r);
+}
+
+static inline void fixup_tlbie_pid_lpid(unsigned long pid, unsigned long lpid)
+{
+	/*
+	 * We can use any address for the invalidation, pick one which is
+	 * probably unused as an optimisation.
+	 */
+	unsigned long va = ((1UL << 52) - 1);
+
+	if (cpu_has_feature(CPU_FTR_P9_TLBIE_ERAT_BUG)) {
+		asm volatile("ptesync" : : : "memory");
+		__tlbie_pid_lpid(0, lpid, RIC_FLUSH_TLB);
+	}
+
+	if (cpu_has_feature(CPU_FTR_P9_TLBIE_STQ_BUG)) {
+		asm volatile("ptesync" : : : "memory");
+		__tlbie_va_lpid(va, pid, lpid, mmu_get_ap(MMU_PAGE_64K),
+				RIC_FLUSH_TLB);
+	}
+}
+
+static inline void _tlbie_pid_lpid(unsigned long pid, unsigned long lpid,
+				   unsigned long ric)
+{
+	asm volatile("ptesync" : : : "memory");
+
+	/*
+	 * Workaround the fact that the "ric" argument to __tlbie_pid
+	 * must be a compile-time contraint to match the "i" constraint
+	 * in the asm statement.
+	 */
+	switch (ric) {
+	case RIC_FLUSH_TLB:
+		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_TLB);
+		fixup_tlbie_pid_lpid(pid, lpid);
+		break;
+	case RIC_FLUSH_PWC:
+		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_PWC);
+		break;
+	case RIC_FLUSH_ALL:
+	default:
+		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_ALL);
+		fixup_tlbie_pid_lpid(pid, lpid);
+	}
+	asm volatile("eieio; tlbsync; ptesync" : : : "memory");
+}
+
+static inline void fixup_tlbie_va_range_lpid(unsigned long va,
+					     unsigned long pid,
+					     unsigned long lpid,
+					     unsigned long ap)
+{
+	if (cpu_has_feature(CPU_FTR_P9_TLBIE_ERAT_BUG)) {
+		asm volatile("ptesync" : : : "memory");
+		__tlbie_pid_lpid(0, lpid, RIC_FLUSH_TLB);
+	}
+
+	if (cpu_has_feature(CPU_FTR_P9_TLBIE_STQ_BUG)) {
+		asm volatile("ptesync" : : : "memory");
+		__tlbie_va_lpid(va, pid, lpid, ap, RIC_FLUSH_TLB);
+	}
+}
+
+static inline void __tlbie_va_range_lpid(unsigned long start, unsigned long end,
+					 unsigned long pid, unsigned long lpid,
+					 unsigned long page_size,
+					 unsigned long psize)
+{
+	unsigned long addr;
+	unsigned long ap = mmu_get_ap(psize);
+
+	for (addr = start; addr < end; addr += page_size)
+		__tlbie_va_lpid(addr, pid, lpid, ap, RIC_FLUSH_TLB);
+
+	fixup_tlbie_va_range_lpid(addr - page_size, pid, lpid, ap);
+}
+
+static inline void _tlbie_va_range_lpid(unsigned long start, unsigned long end,
+					unsigned long pid, unsigned long lpid,
+					unsigned long page_size,
+					unsigned long psize, bool also_pwc)
+{
+	asm volatile("ptesync" : : : "memory");
+	if (also_pwc)
+		__tlbie_pid_lpid(pid, lpid, RIC_FLUSH_PWC);
+	__tlbie_va_range_lpid(start, end, pid, lpid, page_size, psize);
+	asm volatile("eieio; tlbsync; ptesync" : : : "memory");
+}
+
 /*
  * Performs process-scoped invalidations for a given LPID
  * as part of H_RPT_INVALIDATE hcall.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/book3s64/slb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/book3s64/slb.c
@@ -14,6 +14,7 @@
 #include <asm/mmu.h>
 #include <asm/mmu_context.h>
 #include <asm/paca.h>
+#include <asm/lppaca.h>
 #include <asm/ppc-opcode.h>
 #include <asm/cputable.h>
 #include <asm/cacheflush.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/fault.c
@@ -412,10 +412,16 @@
 	/*
 	 * The kernel should never take an execute fault nor should it
 	 * take a page fault to a kernel address or a page fault to a user
-	 * address outside of dedicated places
+	 * address outside of dedicated places.
+	 *
+	 * Rather than kfence directly reporting false negatives, search whether
+	 * the NIP belongs to the fixup table for cases where fault could come
+	 * from functions like copy_from_kernel_nofault().
 	 */
 	if (unlikely(!is_user && bad_kernel_fault(regs, error_code, address, is_write))) {
-		if (kfence_handle_page_fault(address, is_write, regs))
+		if (is_kfence_address((void *)address) &&
+		    !search_exception_tables(instruction_pointer(regs)) &&
+		    kfence_handle_page_fault(address, is_write, regs))
 			return 0;
 
 		return SIGSEGV;
@@ -568,18 +574,24 @@
 static void __bad_page_fault(struct pt_regs *regs, int sig)
 {
 	int is_write = page_fault_is_write(regs->dsisr);
+	const char *msg;
 
 	/* kernel has accessed a bad area */
 
+	if (regs->dar < PAGE_SIZE)
+		msg = "Kernel NULL pointer dereference";
+	else
+		msg = "Unable to handle kernel data access";
+
 	switch (TRAP(regs)) {
 	case INTERRUPT_DATA_STORAGE:
-	case INTERRUPT_DATA_SEGMENT:
 	case INTERRUPT_H_DATA_STORAGE:
-		pr_alert("BUG: %s on %s at 0x%08lx\n",
-			 regs->dar < PAGE_SIZE ? "Kernel NULL pointer dereference" :
-			 "Unable to handle kernel data access",
+		pr_alert("BUG: %s on %s at 0x%08lx\n", msg,
 			 is_write ? "write" : "read", regs->dar);
 		break;
+	case INTERRUPT_DATA_SEGMENT:
+		pr_alert("BUG: %s at 0x%08lx\n", msg, regs->dar);
+		break;
 	case INTERRUPT_INST_STORAGE:
 	case INTERRUPT_INST_SEGMENT:
 		pr_alert("BUG: Unable to handle kernel instruction fetch%s",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/init-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/init-common.c
@@ -105,7 +105,7 @@
 	 * as to leave enough 0 bits in the address to contain it. */
 	unsigned long minalign = max(MAX_PGTABLE_INDEX_SIZE + 1,
 				     HUGEPD_SHIFT_MASK + 1);
-	struct kmem_cache *new;
+	struct kmem_cache *new = NULL;
 
 	/* It would be nice if this was a BUILD_BUG_ON(), but at the
 	 * moment, gcc doesn't seem to recognize is_power_of_2 as a
@@ -118,7 +118,8 @@
 
 	align = max_t(unsigned long, align, minalign);
 	name = kasprintf(GFP_KERNEL, "pgtable-2^%d", shift);
-	new = kmem_cache_create(name, table_size, align, 0, ctor(shift));
+	if (name)
+		new = kmem_cache_create(name, table_size, align, 0, ctor(shift));
 	if (!new)
 		panic("Could not allocate pgtable cache for order %d", shift);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/init_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/init_32.c
@@ -70,12 +70,6 @@
 
 void MMU_init(void);
 
-/*
- * this tells the system to map all of ram with the segregs
- * (i.e. page tables) instead of the bats.
- * -- Cort
- */
-int __map_without_bats;
 int __map_without_ltlbs;
 
 /* max amount of low RAM to map in */
@@ -86,14 +80,6 @@
  */
 static void __init MMU_setup(void)
 {
-	/* Check for nobats option (used in mapin_ram). */
-	if (strstr(boot_command_line, "nobats")) {
-		__map_without_bats = 1;
-	}
-
-	if (strstr(boot_command_line, "noltlbs")) {
-		__map_without_ltlbs = 1;
-	}
 	if (IS_ENABLED(CONFIG_PPC_8xx))
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/init_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/init_64.c
@@ -188,7 +188,7 @@
 	unsigned long nr_pfn = page_size / sizeof(struct page);
 	unsigned long start_pfn = page_to_pfn((struct page *)start);
 
-	if ((start_pfn + nr_pfn) > altmap->end_pfn)
+	if ((start_pfn + nr_pfn - 1) > altmap->end_pfn)
 		return true;
 
 	if (start_pfn < altmap->base_pfn)
@@ -313,8 +313,7 @@
 	start = ALIGN_DOWN(start, page_size);
 	if (altmap) {
 		alt_start = altmap->base_pfn;
-		alt_end = altmap->base_pfn + altmap->reserve +
-			  altmap->free + altmap->alloc + altmap->align;
+		alt_end = altmap->base_pfn + altmap->reserve + altmap->free;
 	}
 
 	pr_debug("vmemmap_free %lx...%lx\n", start, end);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/kasan/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/kasan/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 
 KASAN_SANITIZE := n
+KCOV_INSTRUMENT := n
 
 obj-$(CONFIG_PPC32)           += kasan_init_32.o
 obj-$(CONFIG_PPC_8xx)		+= 8xx.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/kasan/book3s_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/kasan/book3s_32.c
@@ -10,47 +10,51 @@
 {
 	unsigned long k_start = (unsigned long)kasan_mem_to_shadow(start);
 	unsigned long k_end = (unsigned long)kasan_mem_to_shadow(start + size);
-	unsigned long k_cur = k_start;
-	int k_size = k_end - k_start;
-	int k_size_base = 1 << (ffs(k_size) - 1);
+	unsigned long k_nobat = k_start;
+	unsigned long k_cur;
+	phys_addr_t phys;
 	int ret;
-	void *block;
 
-	block = memblock_alloc(k_size, k_size_base);
+	while (k_nobat < k_end) {
+		unsigned int k_size = bat_block_size(k_nobat, k_end);
+		int idx = find_free_bat();
+
+		if (idx == -1)
+			break;
+		if (k_size < SZ_128K)
+			break;
+		phys = memblock_phys_alloc_range(k_size, k_size, 0,
+						 MEMBLOCK_ALLOC_ANYWHERE);
+		if (!phys)
+			break;
 
-	if (block && k_size_base >= SZ_128K && k_start == ALIGN(k_start, k_size_base)) {
-		int k_size_more = 1 << (ffs(k_size - k_size_base) - 1);
-
-		setbat(-1, k_start, __pa(block), k_size_base, PAGE_KERNEL);
-		if (k_size_more >= SZ_128K)
-			setbat(-1, k_start + k_size_base, __pa(block) + k_size_base,
-			       k_size_more, PAGE_KERNEL);
-		if (v_block_mapped(k_start))
-			k_cur = k_start + k_size_base;
-		if (v_block_mapped(k_start + k_size_base))
-			k_cur = k_start + k_size_base + k_size_more;
-
-		update_bats();
+		setbat(idx, k_nobat, phys, k_size, PAGE_KERNEL);
+		k_nobat += k_size;
 	}
+	if (k_nobat != k_start)
+		update_bats();
 
-	if (!block)
-		block = memblock_alloc(k_size, PAGE_SIZE);
-	if (!block)
-		return -ENOMEM;
+	if (k_nobat < k_end) {
+		phys = memblock_phys_alloc_range(k_end - k_nobat, PAGE_SIZE, 0,
+						 MEMBLOCK_ALLOC_ANYWHERE);
+		if (!phys)
+			return -ENOMEM;
+	}
 
 	ret = kasan_init_shadow_page_tables(k_start, k_end);
 	if (ret)
 		return ret;
 
-	kasan_update_early_region(k_start, k_cur, __pte(0));
+	kasan_update_early_region(k_start, k_nobat, __pte(0));
 
-	for (; k_cur < k_end; k_cur += PAGE_SIZE) {
+	for (k_cur = k_nobat; k_cur < k_end; k_cur += PAGE_SIZE) {
 		pmd_t *pmd = pmd_off_k(k_cur);
-		void *va = block + k_cur - k_start;
-		pte_t pte = pfn_pte(PHYS_PFN(__pa(va)), PAGE_KERNEL);
+		pte_t pte = pfn_pte(PHYS_PFN(phys + k_cur - k_nobat), PAGE_KERNEL);
 
 		__set_pte_at(&init_mm, k_cur, pte_offset_kernel(pmd, k_cur), pte, 0);
 	}
 	flush_tlb_kernel_range(k_start, k_end);
+	memset(kasan_mem_to_shadow(start), 0, k_end - k_start);
+
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/kasan/kasan_init_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/kasan/kasan_init_32.c
@@ -64,6 +64,7 @@
 	if (ret)
 		return ret;
 
+	k_start = k_start & PAGE_MASK;
 	block = memblock_alloc(k_end - k_start, PAGE_SIZE);
 	if (!block)
 		return -ENOMEM;
@@ -83,13 +84,12 @@
 kasan_update_early_region(unsigned long k_start, unsigned long k_end, pte_t pte)
 {
 	unsigned long k_cur;
-	phys_addr_t pa = __pa(kasan_early_shadow_page);
 
 	for (k_cur = k_start; k_cur != k_end; k_cur += PAGE_SIZE) {
 		pmd_t *pmd = pmd_off_k(k_cur);
 		pte_t *ptep = pte_offset_kernel(pmd, k_cur);
 
-		if ((pte_val(*ptep) & PTE_RPN_MASK) != pa)
+		if (pte_page(*ptep) != virt_to_page(lm_alias(kasan_early_shadow_page)))
 			continue;
 
 		__set_pte_at(&init_mm, k_cur, ptep, pte, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/mem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/mem.c
@@ -20,8 +20,9 @@
 #include <asm/machdep.h>
 #include <asm/rtas.h>
 #include <asm/kasan.h>
-#include <asm/sparsemem.h>
 #include <asm/svm.h>
+#include <asm/mmzone.h>
+#include <asm/ftrace.h>
 
 #include <mm/mmu_decl.h>
 
@@ -103,6 +104,37 @@
 	vm_unmap_aliases();
 }
 
+/*
+ * After memory hotplug the variables max_pfn, max_low_pfn and high_memory need
+ * updating.
+ */
+static void update_end_of_memory_vars(u64 start, u64 size)
+{
+	unsigned long end_pfn = PFN_UP(start + size);
+
+	if (end_pfn > max_pfn) {
+		max_pfn = end_pfn;
+		max_low_pfn = end_pfn;
+		high_memory = (void *)__va(max_pfn * PAGE_SIZE - 1) + 1;
+	}
+}
+
+int __ref add_pages(int nid, unsigned long start_pfn, unsigned long nr_pages,
+		    struct mhp_params *params)
+{
+	int ret;
+
+	ret = __add_pages(nid, start_pfn, nr_pages, params);
+	if (ret)
+		return ret;
+
+	/* update max_pfn, max_low_pfn and high_memory */
+	update_end_of_memory_vars(start_pfn << PAGE_SHIFT,
+				  nr_pages << PAGE_SHIFT);
+
+	return ret;
+}
+
 int __ref arch_add_memory(int nid, u64 start, u64 size,
 			  struct mhp_params *params)
 {
@@ -113,7 +145,7 @@
 	rc = arch_create_linear_mapping(nid, start, size, params);
 	if (rc)
 		return rc;
-	rc = __add_pages(nid, start_pfn, nr_pages, params);
+	rc = add_pages(nid, start_pfn, nr_pages, params);
 	if (rc)
 		arch_remove_linear_mapping(start, size);
 	return rc;
@@ -255,9 +287,6 @@
 		swiotlb_init(0);
 #endif
 
-	high_memory = (void *) __va(max_low_pfn * PAGE_SIZE);
-	set_max_mapnr(max_pfn);
-
 	kasan_late_init();
 
 	memblock_free_all();
@@ -314,6 +343,7 @@
 	mark_initmem_nx();
 	init_mem_is_free = true;
 	free_initmem_default(POISON_FREE_INITMEM);
+	ftrace_free_init_tramp();
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/mmu_context.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/mmu_context.c
@@ -81,7 +81,7 @@
 	 * context
 	 */
 	if (cpu_has_feature(CPU_FTR_ALTIVEC))
-		asm volatile ("dssall");
+		asm volatile (PPC_DSSALL);
 
 	if (!new_on_cpu)
 		membarrier_arch_switch_mm(prev, next, tsk);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/mmu_decl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/mmu_decl.h
@@ -92,7 +92,6 @@
 extern void setbat(int index, unsigned long virt, phys_addr_t phys,
 		   unsigned int size, pgprot_t prot);
 
-extern int __map_without_bats;
 extern unsigned int rtas_data, rtas_size;
 
 struct hash_pte;
@@ -190,3 +189,8 @@
 {
 	return IS_ENABLED(CONFIG_KFENCE) || debug_pagealloc_enabled();
 }
+
+#ifdef CONFIG_MEMORY_HOTPLUG
+int create_section_mapping(unsigned long start, unsigned long end,
+			   int nid, pgprot_t prot);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/nohash/8xx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/nohash/8xx.c
@@ -18,8 +18,6 @@
 
 #define IMMR_SIZE (FIX_IMMR_SIZE << PAGE_SHIFT)
 
-extern int __map_without_ltlbs;
-
 static unsigned long block_mapped_ram;
 
 /*
@@ -32,8 +30,6 @@
 
 	if (va >= VIRT_IMMR_BASE && va < VIRT_IMMR_BASE + IMMR_SIZE)
 		return p + va - VIRT_IMMR_BASE;
-	if (__map_without_ltlbs)
-		return 0;
 	if (va >= PAGE_OFFSET && va < PAGE_OFFSET + block_mapped_ram)
 		return __pa(va);
 	return 0;
@@ -49,8 +45,6 @@
 
 	if (pa >= p && pa < p + IMMR_SIZE)
 		return VIRT_IMMR_BASE + pa - p;
-	if (__map_without_ltlbs)
-		return 0;
 	if (pa < block_mapped_ram)
 		return (unsigned long)__va(pa);
 	return 0;
@@ -157,14 +151,11 @@
 
 	mmu_mapin_immr();
 
-	if (__map_without_ltlbs)
-		return 0;
-
-	mmu_mapin_ram_chunk(0, boundary, PAGE_KERNEL_TEXT, true);
+	mmu_mapin_ram_chunk(0, boundary, PAGE_KERNEL_X, true);
 	if (debug_pagealloc_enabled_or_kfence()) {
 		top = boundary;
 	} else {
-		mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL_TEXT, true);
+		mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL_X, true);
 		mmu_mapin_ram_chunk(einittext8, top, PAGE_KERNEL, true);
 	}
 
@@ -183,8 +174,8 @@
 	unsigned long boundary = strict_kernel_rwx_enabled() ? sinittext : etext8;
 	unsigned long einittext8 = ALIGN(__pa(_einittext), SZ_8M);
 
-	mmu_mapin_ram_chunk(0, boundary, PAGE_KERNEL_TEXT, false);
-	mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL, false);
+	if (!debug_pagealloc_enabled_or_kfence())
+		mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL, false);
 
 	mmu_pin_tlb(block_mapped_ram, false);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/nohash/book3e_pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/nohash/book3e_pgtable.c
@@ -95,8 +95,8 @@
 		pgdp = pgd_offset_k(ea);
 		p4dp = p4d_offset(pgdp, ea);
 		if (p4d_none(*p4dp)) {
-			pmdp = early_alloc_pgtable(PMD_TABLE_SIZE);
-			p4d_populate(&init_mm, p4dp, pmdp);
+			pudp = early_alloc_pgtable(PUD_TABLE_SIZE);
+			p4d_populate(&init_mm, p4dp, pudp);
 		}
 		pudp = pud_offset(p4dp, ea);
 		if (pud_none(*pudp)) {
@@ -105,7 +105,7 @@
 		}
 		pmdp = pmd_offset(pudp, ea);
 		if (!pmd_present(*pmdp)) {
-			ptep = early_alloc_pgtable(PAGE_SIZE);
+			ptep = early_alloc_pgtable(PTE_TABLE_SIZE);
 			pmd_populate_kernel(&init_mm, pmdp, ptep);
 		}
 		ptep = pte_offset_kernel(pmdp, ea);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/nohash/kaslr_booke.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/nohash/kaslr_booke.c
@@ -18,7 +18,6 @@
 #include <asm/prom.h>
 #include <asm/kdump.h>
 #include <mm/mmu_decl.h>
-#include <generated/compile.h>
 #include <generated/utsrelease.h>
 
 struct regions {
@@ -36,10 +35,6 @@
 	int reserved_mem_size_cells;
 };
 
-/* Simplified build-specific string for starting entropy. */
-static const char build_str[] = UTS_RELEASE " (" LINUX_COMPILE_BY "@"
-		LINUX_COMPILE_HOST ") (" LINUX_COMPILER ") " UTS_VERSION;
-
 struct regions __initdata regions;
 
 static __init void kaslr_get_cmdline(void *fdt)
@@ -72,7 +67,8 @@
 {
 	unsigned long hash = 0;
 
-	hash = rotate_xor(hash, build_str, sizeof(build_str));
+	/* build-specific string for starting entropy. */
+	hash = rotate_xor(hash, linux_banner, strlen(linux_banner));
 	hash = rotate_xor(hash, fdt, fdt_totalsize(fdt));
 
 	return hash;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/nohash/tlb_low_64e.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/nohash/tlb_low_64e.S
@@ -222,7 +222,7 @@
 
 tlb_miss_fault_bolted:
 	/* We need to check if it was an instruction miss */
-	andi.	r10,r11,_PAGE_EXEC|_PAGE_BAP_SX
+	andi.	r10,r11,_PAGE_BAP_UX|_PAGE_BAP_SX
 	bne	itlb_miss_fault_bolted
 dtlb_miss_fault_bolted:
 	tlb_epilog_bolted
@@ -239,7 +239,7 @@
 	srdi	r15,r16,60		/* get region */
 	bne-	itlb_miss_fault_bolted
 
-	li	r11,_PAGE_PRESENT|_PAGE_EXEC	/* Base perm */
+	li	r11,_PAGE_PRESENT|_PAGE_BAP_UX	/* Base perm */
 
 	/* We do the user/kernel test for the PID here along with the RW test
 	 */
@@ -614,7 +614,7 @@
 
 	/* We do the user/kernel test for the PID here along with the RW test
 	 */
-	li	r11,_PAGE_PRESENT|_PAGE_EXEC	/* Base perm */
+	li	r11,_PAGE_PRESENT|_PAGE_BAP_UX	/* Base perm */
 	oris	r11,r11,_PAGE_ACCESSED@h
 
 	cmpldi	cr0,r15,0			/* Check for user region */
@@ -734,7 +734,7 @@
 
 normal_tlb_miss_access_fault:
 	/* We need to check if it was an instruction miss */
-	andi.	r10,r11,_PAGE_EXEC
+	andi.	r10,r11,_PAGE_BAP_UX
 	bne	1f
 	ld	r14,EX_TLB_DEAR(r12)
 	ld	r15,EX_TLB_ESR(r12)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/numa.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/numa.c
@@ -367,6 +367,7 @@
 	WARN(numa_distance_table[nid][nid] == -1,
 	     "NUMA distance details for node %d not provided\n", nid);
 }
+EXPORT_SYMBOL_GPL(update_numa_distance);
 
 /*
  * ibm,numa-lookup-index-table= {N, domainid1, domainid2, ..... domainidN}
@@ -376,9 +377,9 @@
 {
 	int i, j;
 	struct device_node *root;
-	const __u8 *numa_dist_table;
+	const __u8 *form2_distances;
 	const __be32 *numa_lookup_index;
-	int numa_dist_table_length;
+	int form2_distances_length;
 	int max_numa_index, distance_index;
 
 	if (firmware_has_feature(FW_FEATURE_OPAL))
@@ -392,45 +393,41 @@
 	max_numa_index = of_read_number(&numa_lookup_index[0], 1);
 
 	/* first element of the array is the size and is encode-int */
-	numa_dist_table = of_get_property(root, "ibm,numa-distance-table", NULL);
-	numa_dist_table_length = of_read_number((const __be32 *)&numa_dist_table[0], 1);
+	form2_distances = of_get_property(root, "ibm,numa-distance-table", NULL);
+	form2_distances_length = of_read_number((const __be32 *)&form2_distances[0], 1);
 	/* Skip the size which is encoded int */
-	numa_dist_table += sizeof(__be32);
+	form2_distances += sizeof(__be32);
 
-	pr_debug("numa_dist_table_len = %d, numa_dist_indexes_len = %d\n",
-		 numa_dist_table_length, max_numa_index);
+	pr_debug("form2_distances_len = %d, numa_dist_indexes_len = %d\n",
+		 form2_distances_length, max_numa_index);
 
 	for (i = 0; i < max_numa_index; i++)
 		/* +1 skip the max_numa_index in the property */
 		numa_id_index_table[i] = of_read_number(&numa_lookup_index[i + 1], 1);
 
 
-	if (numa_dist_table_length != max_numa_index * max_numa_index) {
+	if (form2_distances_length != max_numa_index * max_numa_index) {
 		WARN(1, "Wrong NUMA distance information\n");
-		/* consider everybody else just remote. */
-		for (i = 0;  i < max_numa_index; i++) {
-			for (j = 0; j < max_numa_index; j++) {
-				int nodeA = numa_id_index_table[i];
-				int nodeB = numa_id_index_table[j];
-
-				if (nodeA == nodeB)
-					numa_distance_table[nodeA][nodeB] = LOCAL_DISTANCE;
-				else
-					numa_distance_table[nodeA][nodeB] = REMOTE_DISTANCE;
-			}
-		}
+		form2_distances = NULL; // don't use it
 	}
-
 	distance_index = 0;
 	for (i = 0;  i < max_numa_index; i++) {
 		for (j = 0; j < max_numa_index; j++) {
 			int nodeA = numa_id_index_table[i];
 			int nodeB = numa_id_index_table[j];
+			int dist;
 
-			numa_distance_table[nodeA][nodeB] = numa_dist_table[distance_index++];
-			pr_debug("dist[%d][%d]=%d ", nodeA, nodeB, numa_distance_table[nodeA][nodeB]);
+			if (form2_distances)
+				dist = form2_distances[distance_index++];
+			else if (nodeA == nodeB)
+				dist = LOCAL_DISTANCE;
+			else
+				dist = REMOTE_DISTANCE;
+			numa_distance_table[nodeA][nodeB] = dist;
+			pr_debug("dist[%d][%d]=%d ", nodeA, nodeB, dist);
 		}
 	}
+
 	of_node_put(root);
 }
 
@@ -960,7 +957,9 @@
 			of_node_put(cpu);
 		}
 
-		node_set_online(nid);
+		/* node_set_online() is an UB if 'nid' is negative */
+		if (likely(nid >= 0))
+			node_set_online(nid);
 	}
 
 	get_n_mem_cells(&n_mem_addr_cells, &n_mem_size_cells);
@@ -1163,6 +1162,9 @@
 {
 	int cpu;
 
+	max_low_pfn = max_pfn = memblock_end_of_DRAM() >> PAGE_SHIFT;
+	min_low_pfn = MEMORY_START >> PAGE_SHIFT;
+
 	/*
 	 * Linux/mm assumes node 0 to be online at boot. However this is not
 	 * true on PowerPC, where node 0 is similar to any other node, it
@@ -1207,9 +1209,6 @@
 {
 	int nid;
 
-	max_low_pfn = memblock_end_of_DRAM() >> PAGE_SHIFT;
-	max_pfn = max_low_pfn;
-
 	memblock_dump_all();
 
 	for_each_online_node(nid) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/pageattr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/pageattr.c
@@ -15,12 +15,14 @@
 #include <asm/pgtable.h>
 
 
+static pte_basic_t pte_update_delta(pte_t *ptep, unsigned long addr,
+				    unsigned long old, unsigned long new)
+{
+	return pte_update(&init_mm, addr, ptep, old & ~new, new & ~old, 0);
+}
+
 /*
- * Updates the attributes of a page in three steps:
- *
- * 1. take the page_table_lock
- * 2. install the new entry with the updated attributes
- * 3. flush the TLB
+ * Updates the attributes of a page atomically.
  *
  * This sequence is safe against concurrent updates, and also allows updating the
  * attributes of a page currently being executed or accessed.
@@ -28,41 +30,39 @@
 static int change_page_attr(pte_t *ptep, unsigned long addr, void *data)
 {
 	long action = (long)data;
-	pte_t pte;
 
-	spin_lock(&init_mm.page_table_lock);
-
-	pte = ptep_get(ptep);
-
-	/* modify the PTE bits as desired, then apply */
+	/* modify the PTE bits as desired */
 	switch (action) {
 	case SET_MEMORY_RO:
-		pte = pte_wrprotect(pte);
+		/* Don't clear DIRTY bit */
+		pte_update_delta(ptep, addr, _PAGE_KERNEL_RW & ~_PAGE_DIRTY, _PAGE_KERNEL_RO);
 		break;
 	case SET_MEMORY_RW:
-		pte = pte_mkwrite(pte_mkdirty(pte));
+		pte_update_delta(ptep, addr, _PAGE_KERNEL_RO, _PAGE_KERNEL_RW);
 		break;
 	case SET_MEMORY_NX:
-		pte = pte_exprotect(pte);
+		pte_update_delta(ptep, addr, _PAGE_KERNEL_ROX, _PAGE_KERNEL_RO);
 		break;
 	case SET_MEMORY_X:
-		pte = pte_mkexec(pte);
+		pte_update_delta(ptep, addr, _PAGE_KERNEL_RO, _PAGE_KERNEL_ROX);
+		break;
+	case SET_MEMORY_NP:
+		pte_update(&init_mm, addr, ptep, _PAGE_PRESENT, 0, 0);
+		break;
+	case SET_MEMORY_P:
+		pte_update(&init_mm, addr, ptep, 0, _PAGE_PRESENT, 0);
 		break;
 	default:
 		WARN_ON_ONCE(1);
 		break;
 	}
 
-	pte_update(&init_mm, addr, ptep, ~0UL, pte_val(pte), 0);
-
 	/* See ptesync comment in radix__set_pte_at() */
 	if (radix_enabled())
 		asm volatile("ptesync": : :"memory");
 
 	flush_tlb_kernel_range(addr, addr + PAGE_SIZE);
 
-	spin_unlock(&init_mm.page_table_lock);
-
 	return 0;
 }
 
@@ -96,36 +96,3 @@
 	return apply_to_existing_page_range(&init_mm, start, size,
 					    change_page_attr, (void *)action);
 }
-
-/*
- * Set the attributes of a page:
- *
- * This function is used by PPC32 at the end of init to set final kernel memory
- * protection. It includes changing the maping of the page it is executing from
- * and data pages it is using.
- */
-static int set_page_attr(pte_t *ptep, unsigned long addr, void *data)
-{
-	pgprot_t prot = __pgprot((unsigned long)data);
-
-	spin_lock(&init_mm.page_table_lock);
-
-	set_pte_at(&init_mm, addr, ptep, pte_modify(*ptep, prot));
-	flush_tlb_kernel_range(addr, addr + PAGE_SIZE);
-
-	spin_unlock(&init_mm.page_table_lock);
-
-	return 0;
-}
-
-int set_memory_attr(unsigned long addr, int numpages, pgprot_t prot)
-{
-	unsigned long start = ALIGN_DOWN(addr, PAGE_SIZE);
-	unsigned long sz = numpages * PAGE_SIZE;
-
-	if (numpages <= 0)
-		return 0;
-
-	return apply_to_existing_page_range(&init_mm, start, sz, set_page_attr,
-					    (void *)pgprot_val(prot));
-}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/pgtable.c
@@ -203,6 +203,15 @@
 	__set_pte_at(mm, addr, ptep, pte, 0);
 }
 
+void unmap_kernel_page(unsigned long va)
+{
+	pmd_t *pmdp = pmd_off_k(va);
+	pte_t *ptep = pte_offset_kernel(pmdp, va);
+
+	pte_clear(&init_mm, va, ptep);
+	flush_tlb_kernel_range(va, va + PAGE_SIZE);
+}
+
 /*
  * This is called when relaxing access to a PTE. It's also called in the page
  * fault path when we don't hit any of the major fault cases, ie, a minor
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/pgtable_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/pgtable_32.c
@@ -138,10 +138,12 @@
 	unsigned long numpages = PFN_UP((unsigned long)_einittext) -
 				 PFN_DOWN((unsigned long)_sinittext);
 
-	if (v_block_mapped((unsigned long)_sinittext))
-		mmu_mark_initmem_nx();
-	else
-		set_memory_attr((unsigned long)_sinittext, numpages, PAGE_KERNEL);
+	mmu_mark_initmem_nx();
+
+	if (!v_block_mapped((unsigned long)_sinittext)) {
+		set_memory_nx((unsigned long)_sinittext, numpages);
+		set_memory_rw((unsigned long)_sinittext, numpages);
+	}
 }
 
 #ifdef CONFIG_STRICT_KERNEL_RWX
@@ -155,25 +157,21 @@
 		return;
 	}
 
-	numpages = PFN_UP((unsigned long)_etext) -
-		   PFN_DOWN((unsigned long)_stext);
-
-	set_memory_attr((unsigned long)_stext, numpages, PAGE_KERNEL_ROX);
 	/*
-	 * mark .rodata as read only. Use __init_begin rather than __end_rodata
-	 * to cover NOTES and EXCEPTION_TABLE.
+	 * mark .text and .rodata as read only. Use __init_begin rather than
+	 * __end_rodata to cover NOTES and EXCEPTION_TABLE.
 	 */
 	numpages = PFN_UP((unsigned long)__init_begin) -
-		   PFN_DOWN((unsigned long)__start_rodata);
+		   PFN_DOWN((unsigned long)_stext);
 
-	set_memory_attr((unsigned long)__start_rodata, numpages, PAGE_KERNEL_RO);
+	set_memory_ro((unsigned long)_stext, numpages);
 
 	// mark_initmem_nx() should have already run by now
 	ptdump_check_wx();
 }
 #endif
 
-#ifdef CONFIG_DEBUG_PAGEALLOC
+#if defined(CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC) && defined(CONFIG_DEBUG_PAGEALLOC)
 void __kernel_map_pages(struct page *page, int numpages, int enable)
 {
 	unsigned long addr = (unsigned long)page_address(page);
@@ -182,8 +180,8 @@
 		return;
 
 	if (enable)
-		set_memory_attr(addr, numpages, PAGE_KERNEL);
+		set_memory_p(addr, numpages);
 	else
-		set_memory_attr(addr, numpages, __pgprot(0));
+		set_memory_np(addr, numpages);
 }
 #endif /* CONFIG_DEBUG_PAGEALLOC */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/pgtable_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/pgtable_64.c
@@ -102,7 +102,8 @@
 struct page *p4d_page(p4d_t p4d)
 {
 	if (p4d_is_leaf(p4d)) {
-		VM_WARN_ON(!p4d_huge(p4d));
+		if (!IS_ENABLED(CONFIG_HAVE_ARCH_HUGE_VMAP))
+			VM_WARN_ON(!p4d_huge(p4d));
 		return pte_page(p4d_pte(p4d));
 	}
 	return virt_to_page(p4d_pgtable(p4d));
@@ -112,7 +113,8 @@
 struct page *pud_page(pud_t pud)
 {
 	if (pud_is_leaf(pud)) {
-		VM_WARN_ON(!pud_huge(pud));
+		if (!IS_ENABLED(CONFIG_HAVE_ARCH_HUGE_VMAP))
+			VM_WARN_ON(!pud_huge(pud));
 		return pte_page(pud_pte(pud));
 	}
 	return virt_to_page(pud_pgtable(pud));
@@ -125,7 +127,13 @@
 struct page *pmd_page(pmd_t pmd)
 {
 	if (pmd_is_leaf(pmd)) {
-		VM_WARN_ON(!(pmd_large(pmd) || pmd_huge(pmd)));
+		/*
+		 * vmalloc_to_page may be called on any vmap address (not only
+		 * vmalloc), and it uses pmd_page() etc., when huge vmap is
+		 * enabled so these checks can't be used.
+		 */
+		if (!IS_ENABLED(CONFIG_HAVE_ARCH_HUGE_VMAP))
+			VM_WARN_ON(!(pmd_large(pmd) || pmd_huge(pmd)));
 		return pte_page(pmd_pte(pmd));
 	}
 	return virt_to_page(pmd_page_vaddr(pmd));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/ptdump/ptdump.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/ptdump/ptdump.c
@@ -183,7 +183,7 @@
 {
 	pte_t pte = __pte(st->current_flags);
 
-	if (!IS_ENABLED(CONFIG_PPC_DEBUG_WX) || !st->check_wx)
+	if (!IS_ENABLED(CONFIG_DEBUG_WX) || !st->check_wx)
 		return;
 
 	if (!pte_write(pte) || !pte_exec(pte))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/mm/ptdump/shared.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/mm/ptdump/shared.c
@@ -17,9 +17,9 @@
 		.clear	= "    ",
 	}, {
 		.mask	= _PAGE_RW,
-		.val	= _PAGE_RW,
-		.set	= "rw",
-		.clear	= "r ",
+		.val	= 0,
+		.set	= "r ",
+		.clear	= "rw",
 	}, {
 		.mask	= _PAGE_EXEC,
 		.val	= _PAGE_EXEC,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/net/bpf_jit_comp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/net/bpf_jit_comp.c
@@ -23,15 +23,15 @@
 	memset32(area, BREAKPOINT_INSTRUCTION, size / 4);
 }
 
-/* Fix the branch target addresses for subprog calls */
-static int bpf_jit_fixup_subprog_calls(struct bpf_prog *fp, u32 *image,
-				       struct codegen_context *ctx, u32 *addrs)
+/* Fix updated addresses (for subprog calls, ldimm64, et al) during extra pass */
+static int bpf_jit_fixup_addresses(struct bpf_prog *fp, u32 *image,
+				   struct codegen_context *ctx, u32 *addrs)
 {
 	const struct bpf_insn *insn = fp->insnsi;
 	bool func_addr_fixed;
 	u64 func_addr;
 	u32 tmp_idx;
-	int i, ret;
+	int i, j, ret;
 
 	for (i = 0; i < fp->len; i++) {
 		/*
@@ -66,6 +66,23 @@
 			 * of the JITed sequence remains unchanged.
 			 */
 			ctx->idx = tmp_idx;
+		} else if (insn[i].code == (BPF_LD | BPF_IMM | BPF_DW)) {
+			tmp_idx = ctx->idx;
+			ctx->idx = addrs[i] / 4;
+#ifdef CONFIG_PPC32
+			PPC_LI32(ctx->b2p[insn[i].dst_reg] - 1, (u32)insn[i + 1].imm);
+			PPC_LI32(ctx->b2p[insn[i].dst_reg], (u32)insn[i].imm);
+			for (j = ctx->idx - addrs[i] / 4; j < 4; j++)
+				EMIT(PPC_RAW_NOP());
+#else
+			func_addr = ((u64)(u32)insn[i].imm) | (((u64)(u32)insn[i + 1].imm) << 32);
+			PPC_LI64(b2p[insn[i].dst_reg], func_addr);
+			/* overwrite rest with nops */
+			for (j = ctx->idx - addrs[i] / 4; j < 5; j++)
+				EMIT(PPC_RAW_NOP());
+#endif
+			ctx->idx = tmp_idx;
+			i++;
 		}
 	}
 
@@ -193,13 +210,13 @@
 		/*
 		 * Do not touch the prologue and epilogue as they will remain
 		 * unchanged. Only fix the branch target address for subprog
-		 * calls in the body.
+		 * calls in the body, and ldimm64 instructions.
 		 *
 		 * This does not change the offsets and lengths of the subprog
 		 * call instruction sequences and hence, the size of the JITed
 		 * image as well.
 		 */
-		bpf_jit_fixup_subprog_calls(fp, code_base, &cgctx, addrs);
+		bpf_jit_fixup_addresses(fp, code_base, &cgctx, addrs);
 
 		/* There is no need to perform the usual passes. */
 		goto skip_codegen_passes;
@@ -241,8 +258,8 @@
 	fp->jited_len = alloclen;
 
 	bpf_flush_icache(bpf_hdr, (u8 *)bpf_hdr + (bpf_hdr->pages * PAGE_SIZE));
-	bpf_jit_binary_lock_ro(bpf_hdr);
 	if (!fp->is_func || extra_pass) {
+		bpf_jit_binary_lock_ro(bpf_hdr);
 		bpf_prog_fill_jited_linfo(fp, addrs);
 out_addrs:
 		kfree(addrs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/net/bpf_jit_comp32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/net/bpf_jit_comp32.c
@@ -191,6 +191,9 @@
 
 	if (image && rel < 0x2000000 && rel >= -0x2000000) {
 		PPC_BL_ABS(func);
+		EMIT(PPC_RAW_NOP());
+		EMIT(PPC_RAW_NOP());
+		EMIT(PPC_RAW_NOP());
 	} else {
 		/* Load function address into r0 */
 		EMIT(PPC_RAW_LIS(_R0, IMM_H(func)));
@@ -289,6 +292,8 @@
 		bool func_addr_fixed;
 		u64 func_addr;
 		u32 true_cond;
+		u32 tmp_idx;
+		int j;
 
 		/*
 		 * addrs[] maps a BPF bytecode address into a real offset from
@@ -836,8 +841,12 @@
 		 * 16 byte instruction that uses two 'struct bpf_insn'
 		 */
 		case BPF_LD | BPF_IMM | BPF_DW: /* dst = (u64) imm */
+			tmp_idx = ctx->idx;
 			PPC_LI32(dst_reg_h, (u32)insn[i + 1].imm);
 			PPC_LI32(dst_reg, (u32)insn[i].imm);
+			/* padding to allow full 4 instructions for later patching */
+			for (j = ctx->idx - tmp_idx; j < 4; j++)
+				EMIT(PPC_RAW_NOP());
 			/* Adjust for two bpf instructions */
 			addrs[++i] = ctx->idx * 4;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/net/bpf_jit_comp64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/net/bpf_jit_comp64.c
@@ -318,6 +318,7 @@
 		u64 imm64;
 		u32 true_cond;
 		u32 tmp_idx;
+		int j;
 
 		/*
 		 * addrs[] maps a BPF bytecode address into a real offset from
@@ -632,17 +633,21 @@
 				EMIT(PPC_RAW_MR(dst_reg, b2p[TMP_REG_1]));
 				break;
 			case 64:
-				/*
-				 * Way easier and faster(?) to store the value
-				 * into stack and then use ldbrx
-				 *
-				 * ctx->seen will be reliable in pass2, but
-				 * the instructions generated will remain the
-				 * same across all passes
-				 */
+				/* Store the value to stack and then use byte-reverse loads */
 				PPC_BPF_STL(dst_reg, 1, bpf_jit_stack_local(ctx));
 				EMIT(PPC_RAW_ADDI(b2p[TMP_REG_1], 1, bpf_jit_stack_local(ctx)));
-				EMIT(PPC_RAW_LDBRX(dst_reg, 0, b2p[TMP_REG_1]));
+				if (cpu_has_feature(CPU_FTR_ARCH_206)) {
+					EMIT(PPC_RAW_LDBRX(dst_reg, 0, b2p[TMP_REG_1]));
+				} else {
+					EMIT(PPC_RAW_LWBRX(dst_reg, 0, b2p[TMP_REG_1]));
+					if (IS_ENABLED(CONFIG_CPU_LITTLE_ENDIAN))
+						EMIT(PPC_RAW_SLDI(dst_reg, dst_reg, 32));
+					EMIT(PPC_RAW_LI(b2p[TMP_REG_2], 4));
+					EMIT(PPC_RAW_LWBRX(b2p[TMP_REG_2], b2p[TMP_REG_2], b2p[TMP_REG_1]));
+					if (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
+						EMIT(PPC_RAW_SLDI(b2p[TMP_REG_2], b2p[TMP_REG_2], 32));
+					EMIT(PPC_RAW_OR(dst_reg, dst_reg, b2p[TMP_REG_2]));
+				}
 				break;
 			}
 			break;
@@ -806,9 +811,13 @@
 		case BPF_LD | BPF_IMM | BPF_DW: /* dst = (u64) imm */
 			imm64 = ((u64)(u32) insn[i].imm) |
 				    (((u64)(u32) insn[i+1].imm) << 32);
+			tmp_idx = ctx->idx;
+			PPC_LI64(dst_reg, imm64);
+			/* padding to allow full 5 instructions for later patching */
+			for (j = ctx->idx - tmp_idx; j < 5; j++)
+				EMIT(PPC_RAW_NOP());
 			/* Adjust for two bpf instructions */
 			addrs[++i] = ctx->idx * 4;
-			PPC_LI64(dst_reg, imm64);
 			break;
 
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/Makefile
@@ -3,11 +3,11 @@
 obj-y				+= callchain.o callchain_$(BITS).o perf_regs.o
 obj-$(CONFIG_COMPAT)		+= callchain_32.o
 
-obj-$(CONFIG_PPC_PERF_CTRS)	+= core-book3s.o bhrb.o
+obj-$(CONFIG_PPC_PERF_CTRS)	+= core-book3s.o
 obj64-$(CONFIG_PPC_PERF_CTRS)	+= ppc970-pmu.o power5-pmu.o \
 				   power5+-pmu.o power6-pmu.o power7-pmu.o \
 				   isa207-common.o power8-pmu.o power9-pmu.o \
-				   generic-compat-pmu.o power10-pmu.o
+				   generic-compat-pmu.o power10-pmu.o bhrb.o
 obj32-$(CONFIG_PPC_PERF_CTRS)	+= mpc7450-pmu.o
 
 obj-$(CONFIG_PPC_POWERNV)	+= imc-pmu.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/callchain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/callchain.c
@@ -61,6 +61,7 @@
 		next_sp = fp[0];
 
 		if (next_sp == sp + STACK_INT_FRAME_SIZE &&
+		    validate_sp(sp, current, STACK_INT_FRAME_SIZE) &&
 		    fp[STACK_FRAME_MARKER] == STACK_FRAME_REGS_MARKER) {
 			/*
 			 * This looks like an interrupt frame for an
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/callchain.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/callchain.h
@@ -2,7 +2,6 @@
 #ifndef _POWERPC_PERF_CALLCHAIN_H
 #define _POWERPC_PERF_CALLCHAIN_H
 
-int read_user_stack_slow(const void __user *ptr, void *buf, int nb);
 void perf_callchain_user_64(struct perf_callchain_entry_ctx *entry,
 			    struct pt_regs *regs);
 void perf_callchain_user_32(struct perf_callchain_entry_ctx *entry,
@@ -26,17 +25,11 @@
 				    size_t size)
 {
 	unsigned long addr = (unsigned long)ptr;
-	int rc;
 
 	if (addr > TASK_SIZE - size || (addr & (size - 1)))
 		return -EFAULT;
 
-	rc = copy_from_user_nofault(ret, ptr, size);
-
-	if (IS_ENABLED(CONFIG_PPC64) && !radix_enabled() && rc)
-		return read_user_stack_slow(ptr, ret, size);
-
-	return rc;
+	return copy_from_user_nofault(ret, ptr, size);
 }
 
 #endif /* _POWERPC_PERF_CALLCHAIN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/callchain_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/callchain_64.c
@@ -18,33 +18,6 @@
 
 #include "callchain.h"
 
-/*
- * On 64-bit we don't want to invoke hash_page on user addresses from
- * interrupt context, so if the access faults, we read the page tables
- * to find which page (if any) is mapped and access it directly. Radix
- * has no need for this so it doesn't use read_user_stack_slow.
- */
-int read_user_stack_slow(const void __user *ptr, void *buf, int nb)
-{
-
-	unsigned long addr = (unsigned long) ptr;
-	unsigned long offset;
-	struct page *page;
-	void *kaddr;
-
-	if (get_user_page_fast_only(addr, FOLL_WRITE, &page)) {
-		kaddr = page_address(page);
-
-		/* align address to page boundary */
-		offset = addr & ~PAGE_MASK;
-
-		memcpy(buf, kaddr + offset, nb);
-		put_page(page);
-		return 0;
-	}
-	return -EFAULT;
-}
-
 static int read_user_stack_64(const unsigned long __user *ptr, unsigned long *ret)
 {
 	return __read_user_stack(ptr, ret, sizeof(*ret));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/core-book3s.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/core-book3s.c
@@ -857,6 +857,19 @@
 	}
 }
 
+static int any_pmc_overflown(struct cpu_hw_events *cpuhw)
+{
+	int i, idx;
+
+	for (i = 0; i < cpuhw->n_events; i++) {
+		idx = cpuhw->event[i]->hw.idx;
+		if ((idx) && ((int)read_pmc(idx) < 0))
+			return idx;
+	}
+
+	return 0;
+}
+
 /* Called from sysrq_handle_showregs() */
 void perf_event_print_debug(void)
 {
@@ -1281,11 +1294,13 @@
 
 		/*
 		 * Set the 'freeze counters' bit, clear EBE/BHRBA/PMCC/PMAO/FC56
+		 * Also clear PMXE to disable PMI's getting triggered in some
+		 * corner cases during PMU disable.
 		 */
 		val  = mmcr0 = mfspr(SPRN_MMCR0);
 		val |= MMCR0_FC;
 		val &= ~(MMCR0_EBE | MMCR0_BHRBA | MMCR0_PMCC | MMCR0_PMAO |
-			 MMCR0_FC56);
+			 MMCR0_PMXE | MMCR0_FC56);
 		/* Set mmcr0 PMCCEXT for p10 */
 		if (ppmu->flags & PPMU_ARCH_31)
 			val |= MMCR0_PMCCEXT;
@@ -1299,13 +1314,35 @@
 		mb();
 		isync();
 
+		/*
+		 * Some corner cases could clear the PMU counter overflow
+		 * while a masked PMI is pending. One such case is when
+		 * a PMI happens during interrupt replay and perf counter
+		 * values are cleared by PMU callbacks before replay.
+		 *
+		 * Disable the interrupt by clearing the paca bit for PMI
+		 * since we are disabling the PMU now. Otherwise provide a
+		 * warning if there is PMI pending, but no counter is found
+		 * overflown.
+		 *
+		 * Since power_pmu_disable runs under local_irq_save, it
+		 * could happen that code hits a PMC overflow without PMI
+		 * pending in paca. Hence only clear PMI pending if it was
+		 * set.
+		 *
+		 * If a PMI is pending, then MSR[EE] must be disabled (because
+		 * the masked PMI handler disabling EE). So it is safe to
+		 * call clear_pmi_irq_pending().
+		 */
+		if (pmi_irq_pending())
+			clear_pmi_irq_pending();
+
 		val = mmcra = cpuhw->mmcr.mmcra;
 
 		/*
 		 * Disable instruction sampling if it was enabled
 		 */
-		if (cpuhw->mmcr.mmcra & MMCRA_SAMPLE_ENABLE)
-			val &= ~MMCRA_SAMPLE_ENABLE;
+		val &= ~MMCRA_SAMPLE_ENABLE;
 
 		/* Disable BHRB via mmcra (BHRBRD) for p10 */
 		if (ppmu->flags & PPMU_ARCH_31)
@@ -1316,7 +1353,7 @@
 		 * instruction sampling or BHRB.
 		 */
 		if (val != mmcra) {
-			mtspr(SPRN_MMCRA, mmcra);
+			mtspr(SPRN_MMCRA, val);
 			mb();
 			isync();
 		}
@@ -1390,6 +1427,15 @@
 	 * (possibly updated for removal of events).
 	 */
 	if (!cpuhw->n_added) {
+		/*
+		 * If there is any active event with an overflown PMC
+		 * value, set back PACA_IRQ_PMI which would have been
+		 * cleared in power_pmu_disable().
+		 */
+		hard_irq_disable();
+		if (any_pmc_overflown(cpuhw))
+			set_pmi_irq_pending();
+
 		mtspr(SPRN_MMCRA, cpuhw->mmcr.mmcra & ~MMCRA_SAMPLE_ENABLE);
 		mtspr(SPRN_MMCR1, cpuhw->mmcr.mmcr1);
 		if (ppmu->flags & PPMU_ARCH_31)
@@ -2337,6 +2383,14 @@
 				break;
 			}
 		}
+
+		/*
+		 * Clear PACA_IRQ_PMI in case it was set by
+		 * set_pmi_irq_pending() when PMU was enabled
+		 * after accounting for interrupts.
+		 */
+		clear_pmi_irq_pending();
+
 		if (!active)
 			/* reset non active counters that have overflowed */
 			write_pmc(i + 1, 0);
@@ -2356,6 +2410,13 @@
 			}
 		}
 	}
+
+	/*
+	 * During system wide profling or while specific CPU is monitored for an
+	 * event, some corner cases could cause PMC to overflow in idle path. This
+	 * will trigger a PMI after waking up from idle. Since counter values are _not_
+	 * saved/restored in idle path, can lead to below "Can't find PMC" message.
+	 */
 	if (unlikely(!found) && !arch_irq_disabled_regs(regs))
 		printk_ratelimited(KERN_WARNING "Can't find PMC that caused IRQ\n");
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/core-fsl-emb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/core-fsl-emb.c
@@ -645,7 +645,6 @@
 	struct cpu_hw_events *cpuhw = this_cpu_ptr(&cpu_hw_events);
 	struct perf_event *event;
 	unsigned long val;
-	int found = 0;
 
 	for (i = 0; i < ppmu->n_counter; ++i) {
 		event = cpuhw->event[i];
@@ -654,7 +653,6 @@
 		if ((int)val < 0) {
 			if (event) {
 				/* event has overflowed */
-				found = 1;
 				record_and_restart(event, val, regs);
 			} else {
 				/*
@@ -672,11 +670,13 @@
 	isync();
 }
 
-void hw_perf_event_setup(int cpu)
+static int fsl_emb_pmu_prepare_cpu(unsigned int cpu)
 {
 	struct cpu_hw_events *cpuhw = &per_cpu(cpu_hw_events, cpu);
 
 	memset(cpuhw, 0, sizeof(*cpuhw));
+
+	return 0;
 }
 
 int register_fsl_emb_pmu(struct fsl_emb_pmu *pmu)
@@ -689,6 +689,8 @@
 		pmu->name);
 
 	perf_pmu_register(&fsl_emb_pmu, "cpu", PERF_TYPE_RAW);
+	cpuhp_setup_state(CPUHP_PERF_POWER, "perf/powerpc:prepare",
+			  fsl_emb_pmu_prepare_cpu, NULL);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/hv-24x7.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/hv-24x7.c
@@ -79,9 +79,8 @@
  */
 void read_24x7_sys_info(void)
 {
-	int call_status, len, ntypes;
-
-	spin_lock(&rtas_data_buf_lock);
+	const s32 token = rtas_token("ibm,get-system-parameter");
+	int call_status;
 
 	/*
 	 * Making system parameter: chips and sockets and cores per chip
@@ -91,32 +90,27 @@
 	phys_chipspersocket = 1;
 	phys_coresperchip = 1;
 
-	call_status = rtas_call(rtas_token("ibm,get-system-parameter"), 3, 1,
-				NULL,
-				PROCESSOR_MODULE_INFO,
-				__pa(rtas_data_buf),
-				RTAS_DATA_BUF_SIZE);
+	do {
+		spin_lock(&rtas_data_buf_lock);
+		call_status = rtas_call(token, 3, 1, NULL, PROCESSOR_MODULE_INFO,
+					__pa(rtas_data_buf), RTAS_DATA_BUF_SIZE);
+		if (call_status == 0) {
+			int ntypes = be16_to_cpup((__be16 *)&rtas_data_buf[2]);
+			int len = be16_to_cpup((__be16 *)&rtas_data_buf[0]);
+
+			if (len >= 8 && ntypes != 0) {
+				phys_sockets = be16_to_cpup((__be16 *)&rtas_data_buf[4]);
+				phys_chipspersocket = be16_to_cpup((__be16 *)&rtas_data_buf[6]);
+				phys_coresperchip = be16_to_cpup((__be16 *)&rtas_data_buf[8]);
+			}
+		}
+		spin_unlock(&rtas_data_buf_lock);
+	} while (rtas_busy_delay(call_status));
 
 	if (call_status != 0) {
 		pr_err("Error calling get-system-parameter %d\n",
 		       call_status);
-	} else {
-		len = be16_to_cpup((__be16 *)&rtas_data_buf[0]);
-		if (len < 8)
-			goto out;
-
-		ntypes = be16_to_cpup((__be16 *)&rtas_data_buf[2]);
-
-		if (!ntypes)
-			goto out;
-
-		phys_sockets = be16_to_cpup((__be16 *)&rtas_data_buf[4]);
-		phys_chipspersocket = be16_to_cpup((__be16 *)&rtas_data_buf[6]);
-		phys_coresperchip = be16_to_cpup((__be16 *)&rtas_data_buf[8]);
 	}
-
-out:
-	spin_unlock(&rtas_data_buf_lock);
 }
 
 /* Domains for which more than one result element are returned for each event. */
@@ -1431,7 +1425,7 @@
 	}
 
 	domain = event_get_domain(event);
-	if (domain >= HV_PERF_DOMAIN_MAX) {
+	if (domain  == 0 || domain >= HV_PERF_DOMAIN_MAX) {
 		pr_devel("invalid domain %d\n", domain);
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/hv-gpci-requests.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/hv-gpci-requests.h
@@ -79,6 +79,7 @@
 )
 #include I(REQUEST_END)
 
+#ifdef ENABLE_EVENTS_COUNTERINFO_V6
 /*
  * Not available for counter_info_version >= 0x8, use
  * run_instruction_cycles_by_partition(0x100) instead.
@@ -92,6 +93,7 @@
 	__count(0x10,	8,	cycles)
 )
 #include I(REQUEST_END)
+#endif
 
 #define REQUEST_NAME system_performance_capabilities
 #define REQUEST_NUM 0x40
@@ -103,6 +105,7 @@
 )
 #include I(REQUEST_END)
 
+#ifdef ENABLE_EVENTS_COUNTERINFO_V6
 #define REQUEST_NAME processor_bus_utilization_abc_links
 #define REQUEST_NUM 0x50
 #define REQUEST_IDX_KIND "hw_chip_id=?"
@@ -194,6 +197,7 @@
 	__count(0x28,	8,	instructions_completed)
 )
 #include I(REQUEST_END)
+#endif
 
 /* Processor_core_power_mode (0x95) skipped, no counters */
 /* Affinity_domain_information_by_virtual_processor (0xA0) skipped,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/hv-gpci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/hv-gpci.c
@@ -72,7 +72,7 @@
 
 static struct attribute_group event_group = {
 	.name  = "events",
-	.attrs = hv_gpci_event_attrs,
+	/* .attrs is set in init */
 };
 
 #define HV_CAPS_ATTR(_name, _format)				\
@@ -164,6 +164,20 @@
 
 	ret = plpar_hcall_norets(H_GET_PERF_COUNTER_INFO,
 			virt_to_phys(arg), HGPCI_REQ_BUFFER_SIZE);
+
+	/*
+	 * ret value as 'H_PARAMETER' with detail_rc as 'GEN_BUF_TOO_SMALL',
+	 * specifies that the current buffer size cannot accommodate
+	 * all the information and a partial buffer returned.
+	 * Since in this function we are only accessing data for a given starting index,
+	 * we don't need to accommodate whole data and can get required count by
+	 * accessing first entry data.
+	 * Hence hcall fails only incase the ret value is other than H_SUCCESS or
+	 * H_PARAMETER with detail_rc value as GEN_BUF_TOO_SMALL(0x1B).
+	 */
+	if (ret == H_PARAMETER && be32_to_cpu(arg->params.detail_rc) == 0x1B)
+		ret = 0;
+
 	if (ret) {
 		pr_devel("hcall failed: 0x%lx\n", ret);
 		goto out;
@@ -228,6 +242,7 @@
 {
 	u64 count;
 	u8 length;
+	unsigned long ret;
 
 	/* Not our event */
 	if (event->attr.type != event->pmu->type)
@@ -258,13 +273,23 @@
 	}
 
 	/* check if the request works... */
-	if (single_gpci_request(event_get_request(event),
+	ret = single_gpci_request(event_get_request(event),
 				event_get_starting_index(event),
 				event_get_secondary_index(event),
 				event_get_counter_info_version(event),
 				event_get_offset(event),
 				length,
-				&count)) {
+				&count);
+
+	/*
+	 * ret value as H_AUTHORITY implies that partition is not permitted to retrieve
+	 * performance information, and required to set
+	 * "Enable Performance Information Collection" option.
+	 */
+	if (ret == H_AUTHORITY)
+		return -EPERM;
+
+	if (ret) {
 		pr_devel("gpci hcall failed\n");
 		return -EINVAL;
 	}
@@ -330,6 +355,7 @@
 	int r;
 	unsigned long hret;
 	struct hv_perf_caps caps;
+	struct hv_gpci_request_buffer *arg;
 
 	hv_gpci_assert_offsets_correct();
 
@@ -353,6 +379,36 @@
 	/* sampling not supported */
 	h_gpci_pmu.capabilities |= PERF_PMU_CAP_NO_INTERRUPT;
 
+	arg = (void *)get_cpu_var(hv_gpci_reqb);
+	memset(arg, 0, HGPCI_REQ_BUFFER_SIZE);
+
+	/*
+	 * hcall H_GET_PERF_COUNTER_INFO populates the output
+	 * counter_info_version value based on the system hypervisor.
+	 * Pass the counter request 0x10 corresponds to request type
+	 * 'Dispatch_timebase_by_processor', to get the supported
+	 * counter_info_version.
+	 */
+	arg->params.counter_request = cpu_to_be32(0x10);
+
+	r = plpar_hcall_norets(H_GET_PERF_COUNTER_INFO,
+			virt_to_phys(arg), HGPCI_REQ_BUFFER_SIZE);
+	if (r) {
+		pr_devel("hcall failed, can't get supported counter_info_version: 0x%x\n", r);
+		arg->params.counter_info_version_out = 0x8;
+	}
+
+	/*
+	 * Use counter_info_version_out value to assign
+	 * required hv-gpci event list.
+	 */
+	if (arg->params.counter_info_version_out >= 0x8)
+		event_group.attrs = hv_gpci_event_attrs;
+	else
+		event_group.attrs = hv_gpci_event_attrs_v6;
+
+	put_cpu_var(hv_gpci_reqb);
+
 	r = perf_pmu_register(&h_gpci_pmu, h_gpci_pmu.name, -1);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/hv-gpci.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/hv-gpci.h
@@ -26,6 +26,7 @@
 #define REQUEST_FILE "../hv-gpci-requests.h"
 #define NAME_LOWER hv_gpci
 #define NAME_UPPER HV_GPCI
+#define ENABLE_EVENTS_COUNTERINFO_V6
 #include "req-gen/perf.h"
 #undef REQUEST_FILE
 #undef NAME_LOWER
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/imc-pmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/imc-pmu.c
@@ -13,6 +13,7 @@
 #include <asm/cputhreads.h>
 #include <asm/smp.h>
 #include <linux/string.h>
+#include <linux/spinlock.h>
 
 /* Nest IMC data structures and variables */
 
@@ -49,7 +50,7 @@
  * core and trace-imc
  */
 static struct imc_pmu_ref imc_global_refc = {
-	.lock = __MUTEX_INITIALIZER(imc_global_refc.lock),
+	.lock = __SPIN_LOCK_UNLOCKED(imc_global_refc.lock),
 	.id = 0,
 	.refc = 0,
 };
@@ -291,6 +292,8 @@
 	attr_group->attrs = attrs;
 	do {
 		ev_val_str = kasprintf(GFP_KERNEL, "event=0x%x", pmu->events[i].value);
+		if (!ev_val_str)
+			continue;
 		dev_str = device_str_attr_create(pmu->events[i].name, ev_val_str);
 		if (!dev_str)
 			continue;
@@ -298,6 +301,8 @@
 		attrs[j++] = dev_str;
 		if (pmu->events[i].scale) {
 			ev_scale_str = kasprintf(GFP_KERNEL, "%s.scale", pmu->events[i].name);
+			if (!ev_scale_str)
+				continue;
 			dev_str = device_str_attr_create(ev_scale_str, pmu->events[i].scale);
 			if (!dev_str)
 				continue;
@@ -307,6 +312,8 @@
 
 		if (pmu->events[i].unit) {
 			ev_unit_str = kasprintf(GFP_KERNEL, "%s.unit", pmu->events[i].name);
+			if (!ev_unit_str)
+				continue;
 			dev_str = device_str_attr_create(ev_unit_str, pmu->events[i].unit);
 			if (!dev_str)
 				continue;
@@ -393,7 +400,7 @@
 				       get_hard_smp_processor_id(cpu));
 		/*
 		 * If this is the last cpu in this chip then, skip the reference
-		 * count mutex lock and make the reference count on this chip zero.
+		 * count lock and make the reference count on this chip zero.
 		 */
 		ref = get_nest_pmu_ref(cpu);
 		if (!ref)
@@ -455,15 +462,15 @@
 	/*
 	 * See if we need to disable the nest PMU.
 	 * If no events are currently in use, then we have to take a
-	 * mutex to ensure that we don't race with another task doing
+	 * lock to ensure that we don't race with another task doing
 	 * enable or disable the nest counters.
 	 */
 	ref = get_nest_pmu_ref(event->cpu);
 	if (!ref)
 		return;
 
-	/* Take the mutex lock for this node and then decrement the reference count */
-	mutex_lock(&ref->lock);
+	/* Take the lock for this node and then decrement the reference count */
+	spin_lock(&ref->lock);
 	if (ref->refc == 0) {
 		/*
 		 * The scenario where this is true is, when perf session is
@@ -475,7 +482,7 @@
 		 * an OPAL call to disable the engine in that node.
 		 *
 		 */
-		mutex_unlock(&ref->lock);
+		spin_unlock(&ref->lock);
 		return;
 	}
 	ref->refc--;
@@ -483,7 +490,7 @@
 		rc = opal_imc_counters_stop(OPAL_IMC_COUNTERS_NEST,
 					    get_hard_smp_processor_id(event->cpu));
 		if (rc) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("nest-imc: Unable to stop the counters for core %d\n", node_id);
 			return;
 		}
@@ -491,7 +498,7 @@
 		WARN(1, "nest-imc: Invalid event reference count\n");
 		ref->refc = 0;
 	}
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 }
 
 static int nest_imc_event_init(struct perf_event *event)
@@ -550,26 +557,25 @@
 
 	/*
 	 * Get the imc_pmu_ref struct for this node.
-	 * Take the mutex lock and then increment the count of nest pmu events
-	 * inited.
+	 * Take the lock and then increment the count of nest pmu events inited.
 	 */
 	ref = get_nest_pmu_ref(event->cpu);
 	if (!ref)
 		return -EINVAL;
 
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	if (ref->refc == 0) {
 		rc = opal_imc_counters_start(OPAL_IMC_COUNTERS_NEST,
 					     get_hard_smp_processor_id(event->cpu));
 		if (rc) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("nest-imc: Unable to start the counters for node %d\n",
 									node_id);
 			return rc;
 		}
 	}
 	++ref->refc;
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 
 	event->destroy = nest_imc_counters_release;
 	return 0;
@@ -605,9 +611,8 @@
 		return -ENOMEM;
 	mem_info->vbase = page_address(page);
 
-	/* Init the mutex */
 	core_imc_refc[core_id].id = core_id;
-	mutex_init(&core_imc_refc[core_id].lock);
+	spin_lock_init(&core_imc_refc[core_id].lock);
 
 	rc = opal_imc_counters_init(OPAL_IMC_COUNTERS_CORE,
 				__pa((void *)mem_info->vbase),
@@ -696,9 +701,8 @@
 		perf_pmu_migrate_context(&core_imc_pmu->pmu, cpu, ncpu);
 	} else {
 		/*
-		 * If this is the last cpu in this core then, skip taking refernce
-		 * count mutex lock for this core and directly zero "refc" for
-		 * this core.
+		 * If this is the last cpu in this core then skip taking reference
+		 * count lock for this core and directly zero "refc" for this core.
 		 */
 		opal_imc_counters_stop(OPAL_IMC_COUNTERS_CORE,
 				       get_hard_smp_processor_id(cpu));
@@ -713,11 +717,11 @@
 		 * last cpu in this core and core-imc event running
 		 * in this cpu.
 		 */
-		mutex_lock(&imc_global_refc.lock);
+		spin_lock(&imc_global_refc.lock);
 		if (imc_global_refc.id == IMC_DOMAIN_CORE)
 			imc_global_refc.refc--;
 
-		mutex_unlock(&imc_global_refc.lock);
+		spin_unlock(&imc_global_refc.lock);
 	}
 	return 0;
 }
@@ -732,7 +736,7 @@
 
 static void reset_global_refc(struct perf_event *event)
 {
-		mutex_lock(&imc_global_refc.lock);
+		spin_lock(&imc_global_refc.lock);
 		imc_global_refc.refc--;
 
 		/*
@@ -744,7 +748,7 @@
 			imc_global_refc.refc = 0;
 			imc_global_refc.id = 0;
 		}
-		mutex_unlock(&imc_global_refc.lock);
+		spin_unlock(&imc_global_refc.lock);
 }
 
 static void core_imc_counters_release(struct perf_event *event)
@@ -757,17 +761,17 @@
 	/*
 	 * See if we need to disable the IMC PMU.
 	 * If no events are currently in use, then we have to take a
-	 * mutex to ensure that we don't race with another task doing
+	 * lock to ensure that we don't race with another task doing
 	 * enable or disable the core counters.
 	 */
 	core_id = event->cpu / threads_per_core;
 
-	/* Take the mutex lock and decrement the refernce count for this core */
+	/* Take the lock and decrement the refernce count for this core */
 	ref = &core_imc_refc[core_id];
 	if (!ref)
 		return;
 
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	if (ref->refc == 0) {
 		/*
 		 * The scenario where this is true is, when perf session is
@@ -779,7 +783,7 @@
 		 * an OPAL call to disable the engine in that core.
 		 *
 		 */
-		mutex_unlock(&ref->lock);
+		spin_unlock(&ref->lock);
 		return;
 	}
 	ref->refc--;
@@ -787,7 +791,7 @@
 		rc = opal_imc_counters_stop(OPAL_IMC_COUNTERS_CORE,
 					    get_hard_smp_processor_id(event->cpu));
 		if (rc) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("IMC: Unable to stop the counters for core %d\n", core_id);
 			return;
 		}
@@ -795,7 +799,7 @@
 		WARN(1, "core-imc: Invalid event reference count\n");
 		ref->refc = 0;
 	}
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 
 	reset_global_refc(event);
 }
@@ -833,7 +837,6 @@
 	if ((!pcmi->vbase))
 		return -ENODEV;
 
-	/* Get the core_imc mutex for this core */
 	ref = &core_imc_refc[core_id];
 	if (!ref)
 		return -EINVAL;
@@ -841,22 +844,22 @@
 	/*
 	 * Core pmu units are enabled only when it is used.
 	 * See if this is triggered for the first time.
-	 * If yes, take the mutex lock and enable the core counters.
+	 * If yes, take the lock and enable the core counters.
 	 * If not, just increment the count in core_imc_refc struct.
 	 */
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	if (ref->refc == 0) {
 		rc = opal_imc_counters_start(OPAL_IMC_COUNTERS_CORE,
 					     get_hard_smp_processor_id(event->cpu));
 		if (rc) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("core-imc: Unable to start the counters for core %d\n",
 									core_id);
 			return rc;
 		}
 	}
 	++ref->refc;
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 
 	/*
 	 * Since the system can run either in accumulation or trace-mode
@@ -867,7 +870,7 @@
 	 * to know whether any other trace/thread imc
 	 * events are running.
 	 */
-	mutex_lock(&imc_global_refc.lock);
+	spin_lock(&imc_global_refc.lock);
 	if (imc_global_refc.id == 0 || imc_global_refc.id == IMC_DOMAIN_CORE) {
 		/*
 		 * No other trace/thread imc events are running in
@@ -876,10 +879,10 @@
 		imc_global_refc.id = IMC_DOMAIN_CORE;
 		imc_global_refc.refc++;
 	} else {
-		mutex_unlock(&imc_global_refc.lock);
+		spin_unlock(&imc_global_refc.lock);
 		return -EBUSY;
 	}
-	mutex_unlock(&imc_global_refc.lock);
+	spin_unlock(&imc_global_refc.lock);
 
 	event->hw.event_base = (u64)pcmi->vbase + (config & IMC_EVENT_OFFSET_MASK);
 	event->destroy = core_imc_counters_release;
@@ -951,10 +954,10 @@
 	mtspr(SPRN_LDBAR, (mfspr(SPRN_LDBAR) & (~(1UL << 63))));
 
 	/* Reduce the refc if thread-imc event running on this cpu */
-	mutex_lock(&imc_global_refc.lock);
+	spin_lock(&imc_global_refc.lock);
 	if (imc_global_refc.id == IMC_DOMAIN_THREAD)
 		imc_global_refc.refc--;
-	mutex_unlock(&imc_global_refc.lock);
+	spin_unlock(&imc_global_refc.lock);
 
 	return 0;
 }
@@ -994,7 +997,7 @@
 	if (!target)
 		return -EINVAL;
 
-	mutex_lock(&imc_global_refc.lock);
+	spin_lock(&imc_global_refc.lock);
 	/*
 	 * Check if any other trace/core imc events are running in the
 	 * system, if not set the global id to thread-imc.
@@ -1003,10 +1006,10 @@
 		imc_global_refc.id = IMC_DOMAIN_THREAD;
 		imc_global_refc.refc++;
 	} else {
-		mutex_unlock(&imc_global_refc.lock);
+		spin_unlock(&imc_global_refc.lock);
 		return -EBUSY;
 	}
-	mutex_unlock(&imc_global_refc.lock);
+	spin_unlock(&imc_global_refc.lock);
 
 	event->pmu->task_ctx_nr = perf_sw_context;
 	event->destroy = reset_global_refc;
@@ -1128,25 +1131,25 @@
 	/*
 	 * imc pmus are enabled only when it is used.
 	 * See if this is triggered for the first time.
-	 * If yes, take the mutex lock and enable the counters.
+	 * If yes, take the lock and enable the counters.
 	 * If not, just increment the count in ref count struct.
 	 */
 	ref = &core_imc_refc[core_id];
 	if (!ref)
 		return -EINVAL;
 
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	if (ref->refc == 0) {
 		if (opal_imc_counters_start(OPAL_IMC_COUNTERS_CORE,
 		    get_hard_smp_processor_id(smp_processor_id()))) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("thread-imc: Unable to start the counter\
 				for core %d\n", core_id);
 			return -EINVAL;
 		}
 	}
 	++ref->refc;
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 	return 0;
 }
 
@@ -1163,12 +1166,12 @@
 		return;
 	}
 
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	ref->refc--;
 	if (ref->refc == 0) {
 		if (opal_imc_counters_stop(OPAL_IMC_COUNTERS_CORE,
 		    get_hard_smp_processor_id(smp_processor_id()))) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("thread-imc: Unable to stop the counters\
 				for core %d\n", core_id);
 			return;
@@ -1176,7 +1179,7 @@
 	} else if (ref->refc < 0) {
 		ref->refc = 0;
 	}
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 
 	/* Set bit 0 of LDBAR to zero, to stop posting updates to memory */
 	mtspr(SPRN_LDBAR, (mfspr(SPRN_LDBAR) & (~(1UL << 63))));
@@ -1217,9 +1220,8 @@
 		}
 	}
 
-	/* Init the mutex, if not already */
 	trace_imc_refc[core_id].id = core_id;
-	mutex_init(&trace_imc_refc[core_id].lock);
+	spin_lock_init(&trace_imc_refc[core_id].lock);
 
 	mtspr(SPRN_LDBAR, 0);
 	return 0;
@@ -1239,10 +1241,10 @@
 	 * Reduce the refc if any trace-imc event running
 	 * on this cpu.
 	 */
-	mutex_lock(&imc_global_refc.lock);
+	spin_lock(&imc_global_refc.lock);
 	if (imc_global_refc.id == IMC_DOMAIN_TRACE)
 		imc_global_refc.refc--;
-	mutex_unlock(&imc_global_refc.lock);
+	spin_unlock(&imc_global_refc.lock);
 
 	return 0;
 }
@@ -1364,17 +1366,17 @@
 	}
 
 	mtspr(SPRN_LDBAR, ldbar_value);
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	if (ref->refc == 0) {
 		if (opal_imc_counters_start(OPAL_IMC_COUNTERS_TRACE,
 				get_hard_smp_processor_id(smp_processor_id()))) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("trace-imc: Unable to start the counters for core %d\n", core_id);
 			return -EINVAL;
 		}
 	}
 	++ref->refc;
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 	return 0;
 }
 
@@ -1407,19 +1409,19 @@
 		return;
 	}
 
-	mutex_lock(&ref->lock);
+	spin_lock(&ref->lock);
 	ref->refc--;
 	if (ref->refc == 0) {
 		if (opal_imc_counters_stop(OPAL_IMC_COUNTERS_TRACE,
 				get_hard_smp_processor_id(smp_processor_id()))) {
-			mutex_unlock(&ref->lock);
+			spin_unlock(&ref->lock);
 			pr_err("trace-imc: Unable to stop the counters for core %d\n", core_id);
 			return;
 		}
 	} else if (ref->refc < 0) {
 		ref->refc = 0;
 	}
-	mutex_unlock(&ref->lock);
+	spin_unlock(&ref->lock);
 
 	trace_imc_event_stop(event, flags);
 }
@@ -1441,7 +1443,7 @@
 	 * no other thread is running any core/thread imc
 	 * events
 	 */
-	mutex_lock(&imc_global_refc.lock);
+	spin_lock(&imc_global_refc.lock);
 	if (imc_global_refc.id == 0 || imc_global_refc.id == IMC_DOMAIN_TRACE) {
 		/*
 		 * No core/thread imc events are running in the
@@ -1450,14 +1452,18 @@
 		imc_global_refc.id = IMC_DOMAIN_TRACE;
 		imc_global_refc.refc++;
 	} else {
-		mutex_unlock(&imc_global_refc.lock);
+		spin_unlock(&imc_global_refc.lock);
 		return -EBUSY;
 	}
-	mutex_unlock(&imc_global_refc.lock);
+	spin_unlock(&imc_global_refc.lock);
 
 	event->hw.idx = -1;
 
-	event->pmu->task_ctx_nr = perf_hw_context;
+	/*
+	 * There can only be a single PMU for perf_hw_context events which is assigned to
+	 * core PMU. Hence use "perf_sw_context" for trace_imc.
+	 */
+	event->pmu->task_ctx_nr = perf_sw_context;
 	event->destroy = reset_global_refc;
 	return 0;
 }
@@ -1522,10 +1528,10 @@
 	i = 0;
 	for_each_node(nid) {
 		/*
-		 * Mutex lock to avoid races while tracking the number of
+		 * Take the lock to avoid races while tracking the number of
 		 * sessions using the chip's nest pmu units.
 		 */
-		mutex_init(&nest_imc_refc[i].lock);
+		spin_lock_init(&nest_imc_refc[i].lock);
 
 		/*
 		 * Loop to init the "id" with the node_id. Variable "i" initialized to
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/isa207-common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/isa207-common.c
@@ -108,7 +108,7 @@
 		*mmcra |= MMCRA_SDAR_MODE_TLB;
 }
 
-static u64 p10_thresh_cmp_val(u64 value)
+static int p10_thresh_cmp_val(u64 value)
 {
 	int exp = 0;
 	u64 result = value;
@@ -139,7 +139,7 @@
 		 * exponent is also zero.
 		 */
 		if (!(value & 0xC0) && exp)
-			result = 0;
+			result = -1;
 		else
 			result = (exp << 8) | value;
 	}
@@ -187,7 +187,7 @@
 	unsigned int cmp, exp;
 
 	if (cpu_has_feature(CPU_FTR_ARCH_31))
-		return p10_thresh_cmp_val(event) != 0;
+		return p10_thresh_cmp_val(event) >= 0;
 
 	/*
 	 * Check the mantissa upper two bits are not zero, unless the
@@ -456,12 +456,14 @@
 			value |= CNST_THRESH_CTL_SEL_VAL(event >> EVENT_THRESH_SHIFT);
 			mask  |= p10_CNST_THRESH_CMP_MASK;
 			value |= p10_CNST_THRESH_CMP_VAL(p10_thresh_cmp_val(event_config1));
-		}
+		} else if (event_is_threshold(event))
+			return -1;
 	} else if (cpu_has_feature(CPU_FTR_ARCH_300))  {
 		if (event_is_threshold(event) && is_thresh_cmp_valid(event)) {
 			mask  |= CNST_THRESH_MASK;
 			value |= CNST_THRESH_VAL(event >> EVENT_THRESH_SHIFT);
-		}
+		} else if (event_is_threshold(event))
+			return -1;
 	} else {
 		/*
 		 * Special case for PM_MRK_FAB_RSP_MATCH and PM_MRK_FAB_RSP_MATCH_CYC,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/power10-events-list.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/power10-events-list.h
@@ -9,10 +9,10 @@
 /*
  * Power10 event codes.
  */
-EVENT(PM_RUN_CYC,				0x600f4);
+EVENT(PM_CYC,				0x600f4);
 EVENT(PM_DISP_STALL_CYC,			0x100f8);
 EVENT(PM_EXEC_STALL,				0x30008);
-EVENT(PM_RUN_INST_CMPL,				0x500fa);
+EVENT(PM_INST_CMPL,				0x500fa);
 EVENT(PM_BR_CMPL,                               0x4d05e);
 EVENT(PM_BR_MPRED_CMPL,                         0x400f6);
 EVENT(PM_BR_FIN,				0x2f04a);
@@ -50,8 +50,8 @@
 /* ITLB Reloaded */
 EVENT(PM_ITLB_MISS,				0x400fc);
 
-EVENT(PM_RUN_CYC_ALT,				0x0001e);
-EVENT(PM_RUN_INST_CMPL_ALT,			0x00002);
+EVENT(PM_CYC_ALT,				0x0001e);
+EVENT(PM_INST_CMPL_ALT,				0x00002);
 
 /*
  * Memory Access Events
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/power10-pmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/power10-pmu.c
@@ -91,8 +91,8 @@
 
 /* Table of alternatives, sorted by column 0 */
 static const unsigned int power10_event_alternatives[][MAX_ALT] = {
-	{ PM_RUN_CYC_ALT,		PM_RUN_CYC },
-	{ PM_RUN_INST_CMPL_ALT,		PM_RUN_INST_CMPL },
+	{ PM_INST_CMPL_ALT,		PM_INST_CMPL },
+	{ PM_CYC_ALT,			PM_CYC },
 };
 
 static int power10_get_alternatives(u64 event, unsigned int flags, u64 alt[])
@@ -118,8 +118,8 @@
 	return 0;
 }
 
-GENERIC_EVENT_ATTR(cpu-cycles,			PM_RUN_CYC);
-GENERIC_EVENT_ATTR(instructions,		PM_RUN_INST_CMPL);
+GENERIC_EVENT_ATTR(cpu-cycles,			PM_CYC);
+GENERIC_EVENT_ATTR(instructions,		PM_INST_CMPL);
 GENERIC_EVENT_ATTR(branch-instructions,		PM_BR_CMPL);
 GENERIC_EVENT_ATTR(branch-misses,		PM_BR_MPRED_CMPL);
 GENERIC_EVENT_ATTR(cache-references,		PM_LD_REF_L1);
@@ -148,8 +148,8 @@
 CACHE_EVENT_ATTR(iTLB-load-misses,		PM_ITLB_MISS);
 
 static struct attribute *power10_events_attr_dd1[] = {
-	GENERIC_EVENT_PTR(PM_RUN_CYC),
-	GENERIC_EVENT_PTR(PM_RUN_INST_CMPL),
+	GENERIC_EVENT_PTR(PM_CYC),
+	GENERIC_EVENT_PTR(PM_INST_CMPL),
 	GENERIC_EVENT_PTR(PM_BR_CMPL),
 	GENERIC_EVENT_PTR(PM_BR_MPRED_CMPL),
 	GENERIC_EVENT_PTR(PM_LD_REF_L1),
@@ -173,8 +173,8 @@
 };
 
 static struct attribute *power10_events_attr[] = {
-	GENERIC_EVENT_PTR(PM_RUN_CYC),
-	GENERIC_EVENT_PTR(PM_RUN_INST_CMPL),
+	GENERIC_EVENT_PTR(PM_CYC),
+	GENERIC_EVENT_PTR(PM_INST_CMPL),
 	GENERIC_EVENT_PTR(PM_BR_FIN),
 	GENERIC_EVENT_PTR(PM_MPRED_BR_FIN),
 	GENERIC_EVENT_PTR(PM_LD_REF_L1),
@@ -271,8 +271,8 @@
 };
 
 static int power10_generic_events_dd1[] = {
-	[PERF_COUNT_HW_CPU_CYCLES] =			PM_RUN_CYC,
-	[PERF_COUNT_HW_INSTRUCTIONS] =			PM_RUN_INST_CMPL,
+	[PERF_COUNT_HW_CPU_CYCLES] =			PM_CYC,
+	[PERF_COUNT_HW_INSTRUCTIONS] =			PM_INST_CMPL,
 	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] =		PM_BR_CMPL,
 	[PERF_COUNT_HW_BRANCH_MISSES] =			PM_BR_MPRED_CMPL,
 	[PERF_COUNT_HW_CACHE_REFERENCES] =		PM_LD_REF_L1,
@@ -280,8 +280,8 @@
 };
 
 static int power10_generic_events[] = {
-	[PERF_COUNT_HW_CPU_CYCLES] =			PM_RUN_CYC,
-	[PERF_COUNT_HW_INSTRUCTIONS] =			PM_RUN_INST_CMPL,
+	[PERF_COUNT_HW_CPU_CYCLES] =			PM_CYC,
+	[PERF_COUNT_HW_INSTRUCTIONS] =			PM_INST_CMPL,
 	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] =		PM_BR_FIN,
 	[PERF_COUNT_HW_BRANCH_MISSES] =			PM_MPRED_BR_FIN,
 	[PERF_COUNT_HW_CACHE_REFERENCES] =		PM_LD_REF_L1,
@@ -548,6 +548,24 @@
 
 #undef C
 
+/*
+ * Set the MMCR0[CC56RUN] bit to enable counting for
+ * PMC5 and PMC6 regardless of the state of CTRL[RUN],
+ * so that we can use counters 5 and 6 as PM_INST_CMPL and
+ * PM_CYC.
+ */
+static int power10_compute_mmcr(u64 event[], int n_ev,
+				unsigned int hwc[], struct mmcr_regs *mmcr,
+				struct perf_event *pevents[], u32 flags)
+{
+	int ret;
+
+	ret = isa207_compute_mmcr(event, n_ev, hwc, mmcr, pevents, flags);
+	if (!ret)
+		mmcr->mmcr0 |= MMCR0_C56RUN;
+	return ret;
+}
+
 static struct power_pmu power10_pmu = {
 	.name			= "POWER10",
 	.n_counter		= MAX_PMU_COUNTERS,
@@ -555,7 +573,7 @@
 	.test_adder		= ISA207_TEST_ADDER,
 	.group_constraint_mask	= CNST_CACHE_PMC4_MASK,
 	.group_constraint_val	= CNST_CACHE_PMC4_VAL,
-	.compute_mmcr		= isa207_compute_mmcr,
+	.compute_mmcr		= power10_compute_mmcr,
 	.config_bhrb		= power10_config_bhrb,
 	.bhrb_filter_map	= power10_bhrb_filter_map,
 	.get_constraint		= isa207_get_constraint,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/power9-pmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/power9-pmu.c
@@ -133,11 +133,11 @@
 
 /* Table of alternatives, sorted by column 0 */
 static const unsigned int power9_event_alternatives[][MAX_ALT] = {
-	{ PM_INST_DISP,			PM_INST_DISP_ALT },
-	{ PM_RUN_CYC_ALT,		PM_RUN_CYC },
-	{ PM_RUN_INST_CMPL_ALT,		PM_RUN_INST_CMPL },
-	{ PM_LD_MISS_L1,		PM_LD_MISS_L1_ALT },
 	{ PM_BR_2PATH,			PM_BR_2PATH_ALT },
+	{ PM_INST_DISP,			PM_INST_DISP_ALT },
+	{ PM_RUN_CYC_ALT,               PM_RUN_CYC },
+	{ PM_LD_MISS_L1,                PM_LD_MISS_L1_ALT },
+	{ PM_RUN_INST_CMPL_ALT,         PM_RUN_INST_CMPL },
 };
 
 static int power9_get_alternatives(u64 event, unsigned int flags, u64 alt[])
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/perf/req-gen/perf.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/perf/req-gen/perf.h
@@ -139,6 +139,26 @@
 #define REQUEST_(r_name, r_value, r_idx_1, r_fields)			\
 	r_fields
 
+/* Generate event list for platforms with counter_info_version 0x6 or below */
+static __maybe_unused struct attribute *hv_gpci_event_attrs_v6[] = {
+#include REQUEST_FILE
+	NULL
+};
+
+/*
+ * Based on getPerfCountInfo v1.018 documentation, some of the hv-gpci
+ * events were deprecated for platform firmware that supports
+ * counter_info_version 0x8 or above.
+ * Those deprecated events are still part of platform firmware that
+ * support counter_info_version 0x6 and below. As per the getPerfCountInfo
+ * v1.018 documentation there is no counter_info_version 0x7.
+ * Undefining macro ENABLE_EVENTS_COUNTERINFO_V6, to disable the addition of
+ * deprecated events in "hv_gpci_event_attrs" attribute group, for platforms
+ * that supports counter_info_version 0x8 or above.
+ */
+#undef ENABLE_EVENTS_COUNTERINFO_V6
+
+/* Generate event list for platforms with counter_info_version 0x8 or above*/
 static __maybe_unused struct attribute *hv_gpci_event_attrs[] = {
 #include REQUEST_FILE
 	NULL
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/44x/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/44x/Kconfig
@@ -177,6 +177,7 @@
 config CURRITUCK
 	bool "IBM Currituck (476fpe) Support"
 	depends on PPC_47x
+	select I2C
 	select SWIOTLB
 	select 476FPE
 	select FORCE_PCI
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/44x/fsp2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/44x/fsp2.c
@@ -208,6 +208,7 @@
 		if (irq == NO_IRQ) {
 			pr_err("device tree node %pOFn is missing a interrupt",
 			      np);
+			of_node_put(np);
 			return;
 		}
 
@@ -215,6 +216,7 @@
 		if (rc) {
 			pr_err("fsp_of_probe: request_irq failed: np=%pOF rc=%d",
 			      np, rc);
+			of_node_put(np);
 			return;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/4xx/cpm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/4xx/cpm.c
@@ -327,6 +327,6 @@
 static int __init cpm_powersave_off(char *arg)
 {
 	cpm.powersave_off = 1;
-	return 0;
+	return 1;
 }
 __setup("powersave=off", cpm_powersave_off);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/512x/clock-commonclk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/512x/clock-commonclk.c
@@ -984,7 +984,7 @@
 
 #define NODE_PREP do { \
 	of_address_to_resource(np, 0, &res); \
-	snprintf(devname, sizeof(devname), "%08x.%s", res.start, np->name); \
+	snprintf(devname, sizeof(devname), "%pa.%s", &res.start, np->name); \
 } while (0)
 
 #define NODE_CHK(clkname, clkitem, regnode, regflag) do { \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c
@@ -530,6 +530,7 @@
  err_bcom_rx_irq:
 	bcom_gen_bd_rx_release(lpbfifo.bcom_rx_task);
  err_bcom_rx:
+	free_irq(lpbfifo.irq, &lpbfifo);
  err_irq:
 	iounmap(lpbfifo.regs);
 	lpbfifo.regs = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/83xx/misc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/83xx/misc.c
@@ -121,17 +121,15 @@
 
 void __init mpc83xx_setup_arch(void)
 {
+	phys_addr_t immrbase = get_immrbase();
+	int immrsize = IS_ALIGNED(immrbase, SZ_2M) ? SZ_2M : SZ_1M;
+	unsigned long va = fix_to_virt(FIX_IMMR_BASE);
+
 	if (ppc_md.progress)
 		ppc_md.progress("mpc83xx_setup_arch()", 0);
 
-	if (!__map_without_bats) {
-		phys_addr_t immrbase = get_immrbase();
-		int immrsize = IS_ALIGNED(immrbase, SZ_2M) ? SZ_2M : SZ_1M;
-		unsigned long va = fix_to_virt(FIX_IMMR_BASE);
-
-		setbat(-1, va, immrbase, immrsize, PAGE_KERNEL_NCG);
-		update_bats();
-	}
+	setbat(-1, va, immrbase, immrsize, PAGE_KERNEL_NCG);
+	update_bats();
 }
 
 int machine_check_83xx(struct pt_regs *regs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/83xx/mpc832x_rdb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/83xx/mpc832x_rdb.c
@@ -106,7 +106,7 @@
 
 		goto next;
 unreg:
-		platform_device_del(pdev);
+		platform_device_put(pdev);
 err:
 		pr_err("%pOF: registration failed\n", np);
 next:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/85xx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/85xx/Makefile
@@ -3,7 +3,9 @@
 # Makefile for the PowerPC 85xx linux kernel.
 #
 obj-$(CONFIG_SMP) += smp.o
-obj-$(CONFIG_FSL_PMC)		  += mpc85xx_pm_ops.o
+ifneq ($(CONFIG_FSL_CORENET_RCPM),y)
+obj-$(CONFIG_SMP) += mpc85xx_pm_ops.o
+endif
 
 obj-y += common.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/85xx/mpc85xx_pm_ops.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/85xx/mpc85xx_pm_ops.c
@@ -17,6 +17,7 @@
 
 static struct ccsr_guts __iomem *guts;
 
+#ifdef CONFIG_FSL_PMC
 static void mpc85xx_irq_mask(int cpu)
 {
 
@@ -49,6 +50,7 @@
 {
 
 }
+#endif
 
 static void mpc85xx_freeze_time_base(bool freeze)
 {
@@ -76,10 +78,12 @@
 
 static const struct fsl_pm_ops mpc85xx_pm_ops = {
 	.freeze_time_base = mpc85xx_freeze_time_base,
+#ifdef CONFIG_FSL_PMC
 	.irq_mask = mpc85xx_irq_mask,
 	.irq_unmask = mpc85xx_irq_unmask,
 	.cpu_die = mpc85xx_cpu_die,
 	.cpu_up_prepare = mpc85xx_cpu_up_prepare,
+#endif
 };
 
 int __init mpc85xx_setup_pmc(void)
@@ -94,9 +98,8 @@
 			pr_err("Could not map guts node address\n");
 			return -ENOMEM;
 		}
+		qoriq_pm_ops = &mpc85xx_pm_ops;
 	}
 
-	qoriq_pm_ops = &mpc85xx_pm_ops;
-
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/85xx/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/85xx/smp.c
@@ -40,7 +40,6 @@
 	u32	pir;
 };
 
-#ifdef CONFIG_HOTPLUG_CPU
 static u64 timebase;
 static int tb_req;
 static int tb_valid;
@@ -112,6 +111,7 @@
 	local_irq_restore(flags);
 }
 
+#ifdef CONFIG_HOTPLUG_CPU
 static void smp_85xx_cpu_offline_self(void)
 {
 	unsigned int cpu = smp_processor_id();
@@ -220,7 +220,7 @@
 	local_irq_save(flags);
 	hard_irq_disable();
 
-	if (qoriq_pm_ops)
+	if (qoriq_pm_ops && qoriq_pm_ops->cpu_up_prepare)
 		qoriq_pm_ops->cpu_up_prepare(cpu);
 
 	/* if cpu is not spinning, reset it */
@@ -292,7 +292,7 @@
 		booting_thread_hwid = cpu_thread_in_core(nr);
 		primary = cpu_first_thread_sibling(nr);
 
-		if (qoriq_pm_ops)
+		if (qoriq_pm_ops && qoriq_pm_ops->cpu_up_prepare)
 			qoriq_pm_ops->cpu_up_prepare(nr);
 
 		/*
@@ -495,21 +495,21 @@
 		smp_85xx_ops.probe = NULL;
 	}
 
-#ifdef CONFIG_HOTPLUG_CPU
 #ifdef CONFIG_FSL_CORENET_RCPM
+	/* Assign a value to qoriq_pm_ops on PPC_E500MC */
 	fsl_rcpm_init();
-#endif
-
-#ifdef CONFIG_FSL_PMC
+#else
+	/* Assign a value to qoriq_pm_ops on !PPC_E500MC */
 	mpc85xx_setup_pmc();
 #endif
 	if (qoriq_pm_ops) {
 		smp_85xx_ops.give_timebase = mpc85xx_give_timebase;
 		smp_85xx_ops.take_timebase = mpc85xx_take_timebase;
+#ifdef CONFIG_HOTPLUG_CPU
 		smp_85xx_ops.cpu_offline_self = smp_85xx_cpu_offline_self;
 		smp_85xx_ops.cpu_die = qoriq_cpu_kill;
-	}
 #endif
+	}
 	smp_ops = &smp_85xx_ops;
 
 #ifdef CONFIG_KEXEC_CORE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/8xx/cpm1.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/8xx/cpm1.c
@@ -280,6 +280,7 @@
 		out_be32(bp, (((BRG_UART_CLK_DIV16 / rate) - 1) << 1) |
 			      CPM_BRG_EN | CPM_BRG_DIV16);
 }
+EXPORT_SYMBOL(cpm_setbrg);
 
 struct cpm_ioport16 {
 	__be16 dir, par, odr_sor, dat, intr;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/8xx/pic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/8xx/pic.c
@@ -153,6 +153,7 @@
 	if (mpc8xx_pic_host == NULL) {
 		printk(KERN_ERR "MPC8xx PIC: failed to allocate irq host!\n");
 		ret = -ENOMEM;
+		goto out;
 	}
 
 	ret = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/Kconfig.cputype
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/Kconfig.cputype
@@ -111,6 +111,7 @@
 
 config PPC_BOOK3E_64
 	bool "Embedded processors"
+	select PPC_FSL_BOOK3E
 	select PPC_FPU # Make it a choice ?
 	select PPC_SMP_MUXED_IPI
 	select PPC_DOORBELL
@@ -136,9 +137,9 @@
 	depends on PPC64 && CPU_LITTLE_ENDIAN
 	select ARCH_HAS_FAST_MULTIPLIER
 
-config GENERIC_CPU
+config POWERPC_CPU
 	bool "Generic 32 bits powerpc"
-	depends on PPC32 && !PPC_8xx
+	depends on PPC32 && !PPC_8xx && !PPC_85xx
 
 config CELL_CPU
 	bool "Cell Broadband Engine"
@@ -169,11 +170,11 @@
 
 config E5500_CPU
 	bool "Freescale e5500"
-	depends on E500
+	depends on PPC64 && E500
 
 config E6500_CPU
 	bool "Freescale e6500"
-	depends on E500
+	depends on PPC64 && E500
 
 config 860_CPU
 	bool "8xx family"
@@ -192,11 +193,23 @@
 	depends on PPC_BOOK3S_32
 	select ALTIVEC
 
+config E500_CPU
+	bool "e500 (8540)"
+	depends on PPC_85xx && !PPC_E500MC
+
+config E500MC_CPU
+	bool "e500mc"
+	depends on PPC_85xx && PPC_E500MC
+
+config TOOLCHAIN_DEFAULT_CPU
+	bool "Rely on the toolchain's implicit default CPU"
+	depends on PPC32
+
 endchoice
 
 config TARGET_CPU_BOOL
 	bool
-	default !GENERIC_CPU
+	default !GENERIC_CPU && !TOOLCHAIN_DEFAULT_CPU
 
 config TARGET_CPU
 	string
@@ -211,6 +224,9 @@
 	default "e300c2" if E300C2_CPU
 	default "e300c3" if E300C3_CPU
 	default "G4" if G4_CPU
+	default "8540" if E500_CPU
+	default "e500mc" if E500MC_CPU
+	default "powerpc" if POWERPC_CPU
 
 config PPC_BOOK3S
 	def_bool y
@@ -287,7 +303,7 @@
 config PPC_FSL_BOOK3E
 	bool
 	select ARCH_SUPPORTS_HUGETLBFS if PHYS_64BIT || PPC64
-	select FSL_EMB_PERFMON
+	imply FSL_EMB_PERFMON
 	select PPC_SMP_MUXED_IPI
 	select PPC_DOORBELL
 	default y if FSL_BOOKE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/book3s/vas-api.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/book3s/vas-api.c
@@ -303,7 +303,7 @@
 		return -EINVAL;
 	}
 
-	if (!cp_inst->coproc->vops && !cp_inst->coproc->vops->open_win) {
+	if (!cp_inst->coproc->vops || !cp_inst->coproc->vops->open_win) {
 		pr_err("VAS API is not registered\n");
 		return -EACCES;
 	}
@@ -373,7 +373,7 @@
 		return -EINVAL;
 	}
 
-	if (!cp_inst->coproc->vops && !cp_inst->coproc->vops->paste_addr) {
+	if (!cp_inst->coproc->vops || !cp_inst->coproc->vops->paste_addr) {
 		pr_err("%s(): VAS API is not registered\n", __func__);
 		return -EACCES;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/cell/axon_msi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/cell/axon_msi.c
@@ -226,6 +226,7 @@
 	if (!prop) {
 		dev_dbg(&dev->dev,
 			"axon_msi: no msi-address-(32|64) properties found\n");
+		of_node_put(dn);
 		return -ENOENT;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/cell/iommu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/cell/iommu.c
@@ -977,6 +977,7 @@
 			if (hbase < dbase || (hend > (dbase + dsize))) {
 				pr_debug("iommu: hash window doesn't fit in"
 					 "real DMA window\n");
+				of_node_put(np);
 				return -1;
 			}
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/cell/pervasive.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/cell/pervasive.c
@@ -78,6 +78,7 @@
 	switch (regs->msr & SRR1_WAKEMASK) {
 	case SRR1_WAKEDEC:
 		set_dec(1);
+		break;
 	case SRR1_WAKEEE:
 		/*
 		 * Handle these when interrupts get re-enabled and we take
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/cell/spufs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/cell/spufs/inode.c
@@ -190,8 +190,10 @@
 			return -ENOMEM;
 		ret = spufs_new_file(dir->d_sb, dentry, files->ops,
 					files->mode & mode, files->size, ctx);
-		if (ret)
+		if (ret) {
+			dput(dentry);
 			return ret;
+		}
 		files++;
 	}
 	return 0;
@@ -434,8 +436,11 @@
 	}
 
 	ret = spufs_mkdir(inode, dentry, flags, mode & 0777);
-	if (ret)
+	if (ret) {
+		if (neighbor)
+			put_spu_context(neighbor);
 		goto out_aff_unlock;
+	}
 
 	if (affinity) {
 		spufs_set_affinity(flags, SPUFS_I(d_inode(dentry))->i_ctx,
@@ -659,6 +664,7 @@
 		return;
 
 	loader = of_get_property(dn, "loader", &size);
+	of_node_put(dn);
 	if (!loader)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/embedded6xx/flipper-pic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/embedded6xx/flipper-pic.c
@@ -145,7 +145,7 @@
 	}
 	io_base = ioremap(res.start, resource_size(&res));
 
-	pr_info("controller at 0x%08x mapped to 0x%p\n", res.start, io_base);
+	pr_info("controller at 0x%pa mapped to 0x%p\n", &res.start, io_base);
 
 	__flipper_quiesce(io_base);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/embedded6xx/hlwd-pic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/embedded6xx/hlwd-pic.c
@@ -171,7 +171,7 @@
 		return NULL;
 	}
 
-	pr_info("controller at 0x%08x mapped to 0x%p\n", res.start, io_base);
+	pr_info("controller at 0x%pa mapped to 0x%p\n", &res.start, io_base);
 
 	__hlwd_quiesce(io_base);
 
@@ -214,6 +214,7 @@
 			irq_set_chained_handler(cascade_virq,
 						hlwd_pic_irq_cascade);
 			hlwd_irq_host = host;
+			of_node_put(np);
 			break;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/embedded6xx/linkstation.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/embedded6xx/linkstation.c
@@ -100,9 +100,6 @@
 	mpic_init(mpic);
 }
 
-extern void avr_uart_configure(void);
-extern void avr_uart_send(const char);
-
 static void __noreturn linkstation_restart(char *cmd)
 {
 	local_irq_disable();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/embedded6xx/mpc10x.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/embedded6xx/mpc10x.h
@@ -156,4 +156,7 @@
 /* For MPC107 boards that use the built-in openpic */
 void mpc10x_set_openpic(void);
 
+void avr_uart_configure(void);
+void avr_uart_send(const char c);
+
 #endif	/* __PPC_KERNEL_MPC10X_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/embedded6xx/wii.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/embedded6xx/wii.c
@@ -89,8 +89,8 @@
 
 	hw_regs = ioremap(res.start, resource_size(&res));
 	if (hw_regs) {
-		pr_info("%s at 0x%08x mapped to 0x%p\n", name,
-			res.start, hw_regs);
+		pr_info("%s at 0x%pa mapped to 0x%p\n", name,
+			&res.start, hw_regs);
 	}
 
 out_put:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/microwatt/microwatt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/microwatt/microwatt.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _MICROWATT_H
+#define _MICROWATT_H
+
+void microwatt_rng_init(void);
+
+#endif /* _MICROWATT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/microwatt/rng.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/microwatt/rng.c
@@ -11,6 +11,7 @@
 #include <asm/archrandom.h>
 #include <asm/cputable.h>
 #include <asm/machdep.h>
+#include "microwatt.h"
 
 #define DARN_ERR 0xFFFFFFFFFFFFFFFFul
 
@@ -29,7 +30,7 @@
 	return 1;
 }
 
-static __init int rng_init(void)
+void __init microwatt_rng_init(void)
 {
 	unsigned long val;
 	int i;
@@ -37,12 +38,7 @@
 	for (i = 0; i < 10; i++) {
 		if (microwatt_get_random_darn(&val)) {
 			ppc_md.get_random_seed = microwatt_get_random_darn;
-			return 0;
+			return;
 		}
 	}
-
-	pr_warn("Unable to use DARN for get_random_seed()\n");
-
-	return -EIO;
 }
-machine_subsys_initcall(, rng_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/microwatt/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/microwatt/setup.c
@@ -16,6 +16,8 @@
 #include <asm/xics.h>
 #include <asm/udbg.h>
 
+#include "microwatt.h"
+
 static void __init microwatt_init_IRQ(void)
 {
 	xics_init();
@@ -32,10 +34,16 @@
 }
 machine_arch_initcall(microwatt, microwatt_populate);
 
+static void __init microwatt_setup_arch(void)
+{
+	microwatt_rng_init();
+}
+
 define_machine(microwatt) {
 	.name			= "microwatt",
 	.probe			= microwatt_probe,
 	.init_IRQ		= microwatt_init_IRQ,
+	.setup_arch		= microwatt_setup_arch,
 	.progress		= udbg_progress,
 	.calibrate_decr		= generic_calibrate_decr,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powermac/cache.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powermac/cache.S
@@ -48,7 +48,7 @@
 
 	/* Stop DST streams */
 BEGIN_FTR_SECTION
-	DSSALL
+	PPC_DSSALL
 	sync
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
 
@@ -197,7 +197,7 @@
 	isync
 
 	/* Stop prefetch streams */
-	DSSALL
+	PPC_DSSALL
 	sync
 
 	/* Disable L2 prefetching */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powermac/low_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powermac/low_i2c.c
@@ -582,6 +582,7 @@
 	bus->close = kw_i2c_close;
 	bus->xfer = kw_i2c_xfer;
 	mutex_init(&bus->mutex);
+	lockdep_register_key(&bus->lock_key);
 	lockdep_set_class(&bus->mutex, &bus->lock_key);
 	if (controller == busnode)
 		bus->flags = pmac_i2c_multibus;
@@ -810,6 +811,7 @@
 		bus->hostdata = bus + 1;
 		bus->xfer = pmu_i2c_xfer;
 		mutex_init(&bus->mutex);
+		lockdep_register_key(&bus->lock_key);
 		lockdep_set_class(&bus->mutex, &bus->lock_key);
 		bus->flags = pmac_i2c_multibus;
 		list_add(&bus->link, &pmac_i2c_busses);
@@ -933,6 +935,7 @@
 		bus->hostdata = bus + 1;
 		bus->xfer = smu_i2c_xfer;
 		mutex_init(&bus->mutex);
+		lockdep_register_key(&bus->lock_key);
 		lockdep_set_class(&bus->mutex, &bus->lock_key);
 		bus->flags = 0;
 		list_add(&bus->link, &pmac_i2c_busses);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-fadump.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-fadump.c
@@ -60,7 +60,7 @@
 	addr = be64_to_cpu(addr);
 	pr_debug("Kernel metadata addr: %llx\n", addr);
 	opal_fdm_active = (void *)addr;
-	if (opal_fdm_active->registered_regions == 0)
+	if (be16_to_cpu(opal_fdm_active->registered_regions) == 0)
 		return;
 
 	ret = opal_mpipl_query_tag(OPAL_MPIPL_TAG_BOOT_MEM, &addr);
@@ -95,17 +95,17 @@
 static void opal_fadump_update_config(struct fw_dump *fadump_conf,
 				      const struct opal_fadump_mem_struct *fdm)
 {
-	pr_debug("Boot memory regions count: %d\n", fdm->region_cnt);
+	pr_debug("Boot memory regions count: %d\n", be16_to_cpu(fdm->region_cnt));
 
 	/*
 	 * The destination address of the first boot memory region is the
 	 * destination address of boot memory regions.
 	 */
-	fadump_conf->boot_mem_dest_addr = fdm->rgn[0].dest;
+	fadump_conf->boot_mem_dest_addr = be64_to_cpu(fdm->rgn[0].dest);
 	pr_debug("Destination address of boot memory regions: %#016llx\n",
 		 fadump_conf->boot_mem_dest_addr);
 
-	fadump_conf->fadumphdr_addr = fdm->fadumphdr_addr;
+	fadump_conf->fadumphdr_addr = be64_to_cpu(fdm->fadumphdr_addr);
 }
 
 /*
@@ -126,9 +126,9 @@
 	fadump_conf->boot_memory_size = 0;
 
 	pr_debug("Boot memory regions:\n");
-	for (i = 0; i < fdm->region_cnt; i++) {
-		base = fdm->rgn[i].src;
-		size = fdm->rgn[i].size;
+	for (i = 0; i < be16_to_cpu(fdm->region_cnt); i++) {
+		base = be64_to_cpu(fdm->rgn[i].src);
+		size = be64_to_cpu(fdm->rgn[i].size);
 		pr_debug("\t[%03d] base: 0x%lx, size: 0x%lx\n", i, base, size);
 
 		fadump_conf->boot_mem_addr[i] = base;
@@ -143,7 +143,7 @@
 	 * Start address of reserve dump area (permanent reservation) for
 	 * re-registering FADump after dump capture.
 	 */
-	fadump_conf->reserve_dump_area_start = fdm->rgn[0].dest;
+	fadump_conf->reserve_dump_area_start = be64_to_cpu(fdm->rgn[0].dest);
 
 	/*
 	 * Rarely, but it can so happen that system crashes before all
@@ -155,13 +155,14 @@
 	 * Hope the memory that could not be preserved only has pages
 	 * that are usually filtered out while saving the vmcore.
 	 */
-	if (fdm->region_cnt > fdm->registered_regions) {
+	if (be16_to_cpu(fdm->region_cnt) > be16_to_cpu(fdm->registered_regions)) {
 		pr_warn("Not all memory regions were saved!!!\n");
 		pr_warn("  Unsaved memory regions:\n");
-		i = fdm->registered_regions;
-		while (i < fdm->region_cnt) {
+		i = be16_to_cpu(fdm->registered_regions);
+		while (i < be16_to_cpu(fdm->region_cnt)) {
 			pr_warn("\t[%03d] base: 0x%llx, size: 0x%llx\n",
-				i, fdm->rgn[i].src, fdm->rgn[i].size);
+				i, be64_to_cpu(fdm->rgn[i].src),
+				be64_to_cpu(fdm->rgn[i].size));
 			i++;
 		}
 
@@ -170,7 +171,7 @@
 	}
 
 	fadump_conf->boot_mem_top = (fadump_conf->boot_memory_size + hole_size);
-	fadump_conf->boot_mem_regs_cnt = fdm->region_cnt;
+	fadump_conf->boot_mem_regs_cnt = be16_to_cpu(fdm->region_cnt);
 	opal_fadump_update_config(fadump_conf, fdm);
 }
 
@@ -178,35 +179,38 @@
 static void opal_fadump_init_metadata(struct opal_fadump_mem_struct *fdm)
 {
 	fdm->version = OPAL_FADUMP_VERSION;
-	fdm->region_cnt = 0;
-	fdm->registered_regions = 0;
-	fdm->fadumphdr_addr = 0;
+	fdm->region_cnt = cpu_to_be16(0);
+	fdm->registered_regions = cpu_to_be16(0);
+	fdm->fadumphdr_addr = cpu_to_be64(0);
 }
 
 static u64 opal_fadump_init_mem_struct(struct fw_dump *fadump_conf)
 {
 	u64 addr = fadump_conf->reserve_dump_area_start;
+	u16 reg_cnt;
 	int i;
 
 	opal_fdm = __va(fadump_conf->kernel_metadata);
 	opal_fadump_init_metadata(opal_fdm);
 
 	/* Boot memory regions */
+	reg_cnt = be16_to_cpu(opal_fdm->region_cnt);
 	for (i = 0; i < fadump_conf->boot_mem_regs_cnt; i++) {
-		opal_fdm->rgn[i].src	= fadump_conf->boot_mem_addr[i];
-		opal_fdm->rgn[i].dest	= addr;
-		opal_fdm->rgn[i].size	= fadump_conf->boot_mem_sz[i];
+		opal_fdm->rgn[i].src	= cpu_to_be64(fadump_conf->boot_mem_addr[i]);
+		opal_fdm->rgn[i].dest	= cpu_to_be64(addr);
+		opal_fdm->rgn[i].size	= cpu_to_be64(fadump_conf->boot_mem_sz[i]);
 
-		opal_fdm->region_cnt++;
+		reg_cnt++;
 		addr += fadump_conf->boot_mem_sz[i];
 	}
+	opal_fdm->region_cnt = cpu_to_be16(reg_cnt);
 
 	/*
 	 * Kernel metadata is passed to f/w and retrieved in capture kerenl.
 	 * So, use it to save fadump header address instead of calculating it.
 	 */
-	opal_fdm->fadumphdr_addr = (opal_fdm->rgn[0].dest +
-				    fadump_conf->boot_memory_size);
+	opal_fdm->fadumphdr_addr = cpu_to_be64(be64_to_cpu(opal_fdm->rgn[0].dest) +
+					       fadump_conf->boot_memory_size);
 
 	opal_fadump_update_config(fadump_conf, opal_fdm);
 
@@ -269,18 +273,21 @@
 static int opal_fadump_register(struct fw_dump *fadump_conf)
 {
 	s64 rc = OPAL_PARAMETER;
+	u16 registered_regs;
 	int i, err = -EIO;
 
-	for (i = 0; i < opal_fdm->region_cnt; i++) {
+	registered_regs = be16_to_cpu(opal_fdm->registered_regions);
+	for (i = 0; i < be16_to_cpu(opal_fdm->region_cnt); i++) {
 		rc = opal_mpipl_update(OPAL_MPIPL_ADD_RANGE,
-				       opal_fdm->rgn[i].src,
-				       opal_fdm->rgn[i].dest,
-				       opal_fdm->rgn[i].size);
+				       be64_to_cpu(opal_fdm->rgn[i].src),
+				       be64_to_cpu(opal_fdm->rgn[i].dest),
+				       be64_to_cpu(opal_fdm->rgn[i].size));
 		if (rc != OPAL_SUCCESS)
 			break;
 
-		opal_fdm->registered_regions++;
+		registered_regs++;
 	}
+	opal_fdm->registered_regions = cpu_to_be16(registered_regs);
 
 	switch (rc) {
 	case OPAL_SUCCESS:
@@ -291,7 +298,8 @@
 	case OPAL_RESOURCE:
 		/* If MAX regions limit in f/w is hit, warn and proceed. */
 		pr_warn("%d regions could not be registered for MPIPL as MAX limit is reached!\n",
-			(opal_fdm->region_cnt - opal_fdm->registered_regions));
+			(be16_to_cpu(opal_fdm->region_cnt) -
+			 be16_to_cpu(opal_fdm->registered_regions)));
 		fadump_conf->dump_registered = 1;
 		err = 0;
 		break;
@@ -312,7 +320,7 @@
 	 * If some regions were registered before OPAL_MPIPL_ADD_RANGE
 	 * OPAL call failed, unregister all regions.
 	 */
-	if ((err < 0) && (opal_fdm->registered_regions > 0))
+	if ((err < 0) && (be16_to_cpu(opal_fdm->registered_regions) > 0))
 		opal_fadump_unregister(fadump_conf);
 
 	return err;
@@ -328,7 +336,7 @@
 		return -EIO;
 	}
 
-	opal_fdm->registered_regions = 0;
+	opal_fdm->registered_regions = cpu_to_be16(0);
 	fadump_conf->dump_registered = 0;
 	return 0;
 }
@@ -563,19 +571,20 @@
 	else
 		fdm_ptr = opal_fdm;
 
-	for (i = 0; i < fdm_ptr->region_cnt; i++) {
+	for (i = 0; i < be16_to_cpu(fdm_ptr->region_cnt); i++) {
 		/*
 		 * Only regions that are registered for MPIPL
 		 * would have dump data.
 		 */
 		if ((fadump_conf->dump_active) &&
-		    (i < fdm_ptr->registered_regions))
-			dumped_bytes = fdm_ptr->rgn[i].size;
+		    (i < be16_to_cpu(fdm_ptr->registered_regions)))
+			dumped_bytes = be64_to_cpu(fdm_ptr->rgn[i].size);
 
 		seq_printf(m, "DUMP: Src: %#016llx, Dest: %#016llx, ",
-			   fdm_ptr->rgn[i].src, fdm_ptr->rgn[i].dest);
+			   be64_to_cpu(fdm_ptr->rgn[i].src),
+			   be64_to_cpu(fdm_ptr->rgn[i].dest));
 		seq_printf(m, "Size: %#llx, Dumped: %#llx bytes\n",
-			   fdm_ptr->rgn[i].size, dumped_bytes);
+			   be64_to_cpu(fdm_ptr->rgn[i].size), dumped_bytes);
 	}
 
 	/* Dump is active. Show reserved area start address. */
@@ -624,6 +633,7 @@
 {
 	const __be32 *prop;
 	unsigned long dn;
+	__be64 be_addr;
 	u64 addr = 0;
 	int i, len;
 	s64 ret;
@@ -680,13 +690,13 @@
 	if (!prop)
 		return;
 
-	ret = opal_mpipl_query_tag(OPAL_MPIPL_TAG_KERNEL, &addr);
-	if ((ret != OPAL_SUCCESS) || !addr) {
+	ret = opal_mpipl_query_tag(OPAL_MPIPL_TAG_KERNEL, &be_addr);
+	if ((ret != OPAL_SUCCESS) || !be_addr) {
 		pr_err("Failed to get Kernel metadata (%lld)\n", ret);
 		return;
 	}
 
-	addr = be64_to_cpu(addr);
+	addr = be64_to_cpu(be_addr);
 	pr_debug("Kernel metadata addr: %llx\n", addr);
 
 	opal_fdm_active = __va(addr);
@@ -697,14 +707,14 @@
 	}
 
 	/* Kernel regions not registered with f/w for MPIPL */
-	if (opal_fdm_active->registered_regions == 0) {
+	if (be16_to_cpu(opal_fdm_active->registered_regions) == 0) {
 		opal_fdm_active = NULL;
 		return;
 	}
 
-	ret = opal_mpipl_query_tag(OPAL_MPIPL_TAG_CPU, &addr);
-	if (addr) {
-		addr = be64_to_cpu(addr);
+	ret = opal_mpipl_query_tag(OPAL_MPIPL_TAG_CPU, &be_addr);
+	if (be_addr) {
+		addr = be64_to_cpu(be_addr);
 		pr_debug("CPU metadata addr: %llx\n", addr);
 		opal_cpu_metadata = __va(addr);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-fadump.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-fadump.h
@@ -31,14 +31,14 @@
  * OPAL FADump kernel metadata
  *
  * The address of this structure will be registered with f/w for retrieving
- * and processing during crash dump.
+ * in the capture kernel to process the crash dump.
  */
 struct opal_fadump_mem_struct {
 	u8	version;
 	u8	reserved[3];
-	u16	region_cnt;		/* number of regions */
-	u16	registered_regions;	/* Regions registered for MPIPL */
-	u64	fadumphdr_addr;
+	__be16	region_cnt;		/* number of regions */
+	__be16	registered_regions;	/* Regions registered for MPIPL */
+	__be64	fadumphdr_addr;
 	struct opal_mpipl_region	rgn[FADUMP_MAX_MEM_REGS];
 } __packed;
 
@@ -135,7 +135,7 @@
 	for (i = 0; i < regs_cnt; i++, bufp += reg_entry_size) {
 		reg_entry = (struct hdat_fadump_reg_entry *)bufp;
 		val = (cpu_endian ? be64_to_cpu(reg_entry->reg_val) :
-		       reg_entry->reg_val);
+		       (u64)(reg_entry->reg_val));
 		opal_fadump_set_regval_regnum(regs,
 					      be32_to_cpu(reg_entry->reg_type),
 					      be32_to_cpu(reg_entry->reg_num),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-irqchip.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-irqchip.c
@@ -275,11 +275,14 @@
 		else
 			name = kasprintf(GFP_KERNEL, "opal");
 
+		if (!name)
+			continue;
 		/* Install interrupt handler */
 		rc = request_irq(r->start, opal_interrupt, r->flags & IRQD_TRIGGER_MASK,
 				 name, NULL);
 		if (rc) {
 			pr_warn("Error %d requesting OPAL irq %d\n", rc, (int)r->start);
+			kfree(name);
 			continue;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-lpc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-lpc.c
@@ -396,6 +396,7 @@
 		if (!of_get_property(np, "primary", NULL))
 			continue;
 		opal_lpc_chip_id = of_get_ibm_chip_id(np);
+		of_node_put(np);
 		break;
 	}
 	if (opal_lpc_chip_id < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-powercap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-powercap.c
@@ -196,6 +196,12 @@
 
 		j = 0;
 		pcaps[i].pg.name = kasprintf(GFP_KERNEL, "%pOFn", node);
+		if (!pcaps[i].pg.name) {
+			kfree(pcaps[i].pattrs);
+			kfree(pcaps[i].pg.attrs);
+			goto out_pcaps_pattrs;
+		}
+
 		if (has_min) {
 			powercap_add_attr(min, "powercap-min",
 					  &pcaps[i].pattrs[j]);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-prd.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-prd.c
@@ -24,13 +24,20 @@
 #include <linux/uaccess.h>
 
 
+struct opal_prd_msg {
+	union {
+		struct opal_prd_msg_header header;
+		DECLARE_FLEX_ARRAY(u8, data);
+	};
+};
+
 /*
  * The msg member must be at the end of the struct, as it's followed by the
  * message data.
  */
 struct opal_prd_msg_queue_item {
-	struct list_head		list;
-	struct opal_prd_msg_header	msg;
+	struct list_head	list;
+	struct opal_prd_msg	msg;
 };
 
 static struct device_node *prd_node;
@@ -156,7 +163,7 @@
 	int rc;
 
 	/* we need at least a header's worth of data */
-	if (count < sizeof(item->msg))
+	if (count < sizeof(item->msg.header))
 		return -EINVAL;
 
 	if (*ppos)
@@ -186,7 +193,7 @@
 			return -EINTR;
 	}
 
-	size = be16_to_cpu(item->msg.size);
+	size = be16_to_cpu(item->msg.header.size);
 	if (size > count) {
 		err = -EINVAL;
 		goto err_requeue;
@@ -352,7 +359,7 @@
 	if (!item)
 		return -ENOMEM;
 
-	memcpy(&item->msg, msg->params, msg_size);
+	memcpy(&item->msg.data, msg->params, msg_size);
 
 	spin_lock_irqsave(&opal_prd_msg_queue_lock, flags);
 	list_add_tail(&item->list, &opal_prd_msg_queue);
@@ -369,6 +376,12 @@
 	.priority	= 0,
 };
 
+static struct notifier_block opal_prd_event_nb2 = {
+	.notifier_call	= opal_prd_msg_notifier,
+	.next		= NULL,
+	.priority	= 0,
+};
+
 static int opal_prd_probe(struct platform_device *pdev)
 {
 	int rc;
@@ -390,9 +403,10 @@
 		return rc;
 	}
 
-	rc = opal_message_notifier_register(OPAL_MSG_PRD2, &opal_prd_event_nb);
+	rc = opal_message_notifier_register(OPAL_MSG_PRD2, &opal_prd_event_nb2);
 	if (rc) {
 		pr_err("Couldn't register PRD2 event notifier\n");
+		opal_message_notifier_unregister(OPAL_MSG_PRD, &opal_prd_event_nb);
 		return rc;
 	}
 
@@ -401,6 +415,8 @@
 		pr_err("failed to register miscdev\n");
 		opal_message_notifier_unregister(OPAL_MSG_PRD,
 				&opal_prd_event_nb);
+		opal_message_notifier_unregister(OPAL_MSG_PRD2,
+				&opal_prd_event_nb2);
 		return rc;
 	}
 
@@ -411,6 +427,7 @@
 {
 	misc_deregister(&opal_prd_dev);
 	opal_message_notifier_unregister(OPAL_MSG_PRD, &opal_prd_event_nb);
+	opal_message_notifier_unregister(OPAL_MSG_PRD2, &opal_prd_event_nb2);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal-xscom.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal-xscom.c
@@ -165,6 +165,11 @@
 	ent->chip = chip;
 	snprintf(ent->name, 16, "%08x", chip);
 	ent->path.data = (void *)kasprintf(GFP_KERNEL, "%pOF", dn);
+	if (!ent->path.data) {
+		kfree(ent);
+		return -ENOMEM;
+	}
+
 	ent->path.size = strlen((char *)ent->path.data);
 
 	dir = debugfs_create_dir(ent->name, root);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/opal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/opal.c
@@ -892,6 +892,7 @@
 	kobj = kobject_create_and_add("exports", opal_kobj);
 	if (!kobj) {
 		pr_warn("kobject_create_and_add() of exports failed\n");
+		of_node_put(np);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/pci-ioda.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/pci-ioda.c
@@ -1618,6 +1618,7 @@
 	tbl->it_ops = &pnv_ioda1_iommu_ops;
 	pe->table_group.tce32_start = tbl->it_offset << tbl->it_page_shift;
 	pe->table_group.tce32_size = tbl->it_size << tbl->it_page_shift;
+	tbl->it_index = (phb->hose->global_number << 16) | pe->pe_number;
 	if (!iommu_init_table(tbl, phb->hose->node, 0, 0))
 		panic("Failed to initialize iommu table");
 
@@ -1788,6 +1789,7 @@
 		res_end = min(window_size, SZ_4G) >> tbl->it_page_shift;
 	}
 
+	tbl->it_index = (pe->phb->hose->global_number << 16) | pe->pe_number;
 	if (iommu_init_table(tbl, pe->phb->hose->node, res_start, res_end))
 		rc = pnv_pci_ioda2_set_window(&pe->table_group, 0, tbl);
 	else
@@ -2332,7 +2334,8 @@
 	int index;
 	int64_t rc;
 
-	if (!res || !res->flags || res->start > res->end)
+	if (!res || !res->flags || res->start > res->end ||
+	    res->flags & IORESOURCE_UNSET)
 		return;
 
 	if (res->flags & IORESOURCE_IO) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/pci-sriov.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/pci-sriov.c
@@ -600,12 +600,12 @@
 	struct pnv_iov_data   *iov;
 
 	iov = pnv_iov_get(pdev);
-	num_vfs = iov->num_vfs;
-	base_pe = iov->vf_pe_arr[0].pe_number;
-
 	if (WARN_ON(!iov))
 		return;
 
+	num_vfs = iov->num_vfs;
+	base_pe = iov->vf_pe_arr[0].pe_number;
+
 	/* Release VF PEs */
 	pnv_ioda_release_vf_PE(pdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/powernv.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/powernv.h
@@ -42,4 +42,6 @@
 u32 memcons_get_size(struct memcons *mc);
 struct memcons *memcons_init(struct device_node *node, const char *mc_prop_name);
 
+void pnv_rng_init(void);
+
 #endif /* _POWERNV_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/rng.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/rng.c
@@ -17,6 +17,7 @@
 #include <asm/prom.h>
 #include <asm/machdep.h>
 #include <asm/smp.h>
+#include "powernv.h"
 
 #define DARN_ERR 0xFFFFFFFFFFFFFFFFul
 
@@ -28,22 +29,16 @@
 
 static DEFINE_PER_CPU(struct powernv_rng *, powernv_rng);
 
-
-int powernv_hwrng_present(void)
-{
-	struct powernv_rng *rng;
-
-	rng = get_cpu_var(powernv_rng);
-	put_cpu_var(rng);
-	return rng != NULL;
-}
-
 static unsigned long rng_whiten(struct powernv_rng *rng, unsigned long val)
 {
 	unsigned long parity;
 
 	/* Calculate the parity of the value */
-	asm ("popcntd %0,%1" : "=r" (parity) : "r" (val));
+	asm (".machine push;   \
+	      .machine power7; \
+	      popcntd %0,%1;   \
+	      .machine pop;"
+	     : "=r" (parity) : "r" (val));
 
 	/* xor our value with the previous mask */
 	val ^= rng->mask;
@@ -54,17 +49,6 @@
 	return val;
 }
 
-int powernv_get_random_real_mode(unsigned long *v)
-{
-	struct powernv_rng *rng;
-
-	rng = raw_cpu_read(powernv_rng);
-
-	*v = rng_whiten(rng, __raw_rm_readq(rng->regs_real));
-
-	return 1;
-}
-
 static int powernv_get_random_darn(unsigned long *v)
 {
 	unsigned long val;
@@ -94,9 +78,6 @@
 			return 0;
 		}
 	}
-
-	pr_warn("Unable to use DARN for get_random_seed()\n");
-
 	return -EIO;
 }
 
@@ -104,12 +85,14 @@
 {
 	struct powernv_rng *rng;
 
-	rng = get_cpu_var(powernv_rng);
-
-	*v = rng_whiten(rng, in_be64(rng->regs));
-
-	put_cpu_var(rng);
-
+	if (mfmsr() & MSR_DR) {
+		rng = get_cpu_var(powernv_rng);
+		*v = rng_whiten(rng, in_be64(rng->regs));
+		put_cpu_var(rng);
+	} else {
+		rng = raw_cpu_read(powernv_rng);
+		*v = rng_whiten(rng, __raw_rm_readq(rng->regs_real));
+	}
 	return 1;
 }
 EXPORT_SYMBOL_GPL(powernv_get_random_long);
@@ -159,32 +142,59 @@
 
 	rng_init_per_cpu(rng, dn);
 
-	pr_info_once("Registering arch random hook.\n");
-
 	ppc_md.get_random_seed = powernv_get_random_long;
 
 	return 0;
 }
 
-static __init int rng_init(void)
+static int __init pnv_get_random_long_early(unsigned long *v)
 {
 	struct device_node *dn;
-	int rc;
 
-	for_each_compatible_node(dn, NULL, "ibm,power-rng") {
-		rc = rng_create(dn);
-		if (rc) {
-			pr_err("Failed creating rng for %pOF (%d).\n",
-				dn, rc);
-			continue;
-		}
+	if (!slab_is_available())
+		return 0;
 
-		/* Create devices for hwrng driver */
-		of_platform_device_create(dn, NULL, NULL);
-	}
+	if (cmpxchg(&ppc_md.get_random_seed, pnv_get_random_long_early,
+		    NULL) != pnv_get_random_long_early)
+		return 0;
+
+	for_each_compatible_node(dn, NULL, "ibm,power-rng")
+		rng_create(dn);
+
+	if (!ppc_md.get_random_seed)
+		return 0;
+	return ppc_md.get_random_seed(v);
+}
+
+void __init pnv_rng_init(void)
+{
+	struct device_node *dn;
+
+	/* Prefer darn over the rest. */
+	if (!initialise_darn())
+		return;
+
+	dn = of_find_compatible_node(NULL, NULL, "ibm,power-rng");
+	if (dn)
+		ppc_md.get_random_seed = pnv_get_random_long_early;
+
+	of_node_put(dn);
+}
 
-	initialise_darn();
+static int __init pnv_rng_late_init(void)
+{
+	struct device_node *dn;
+	unsigned long v;
+
+	/* In case it wasn't called during init for some other reason. */
+	if (ppc_md.get_random_seed == pnv_get_random_long_early)
+		pnv_get_random_long_early(&v);
+
+	if (ppc_md.get_random_seed == powernv_get_random_long) {
+		for_each_compatible_node(dn, NULL, "ibm,power-rng")
+			of_platform_device_create(dn, NULL, NULL);
+	}
 
 	return 0;
 }
-machine_subsys_initcall(powernv, rng_init);
+machine_subsys_initcall(powernv, pnv_rng_late_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/setup.c
@@ -190,6 +190,8 @@
 	pnv_check_guarded_cores();
 
 	/* XXX PMCS */
+
+	pnv_rng_init();
 }
 
 static void __init pnv_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/ultravisor.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/ultravisor.c
@@ -55,6 +55,7 @@
 		return -ENODEV;
 
 	uv_memcons = memcons_init(node, "memcons");
+	of_node_put(node);
 	if (!uv_memcons)
 		return -ENOENT;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/vas-fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/vas-fault.c
@@ -216,7 +216,7 @@
 	vas_init_rx_win_attr(&attr, VAS_COP_TYPE_FAULT);
 
 	attr.rx_fifo_size = vinst->fault_fifo_size;
-	attr.rx_fifo = vinst->fault_fifo;
+	attr.rx_fifo = __pa(vinst->fault_fifo);
 
 	/*
 	 * Max creds is based on number of CRBs can fit in the FIFO.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/vas-window.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/vas-window.c
@@ -404,7 +404,7 @@
 	 *
 	 * See also: Design note in function header.
 	 */
-	val = __pa(winctx->rx_fifo);
+	val = winctx->rx_fifo;
 	val = SET_FIELD(VAS_PAGE_MIGRATION_SELECT, val, 0);
 	write_hvwc_reg(window, VREG(LFIFO_BAR), val);
 
@@ -739,7 +739,7 @@
 		 */
 		winctx->fifo_disable = true;
 		winctx->intr_disable = true;
-		winctx->rx_fifo = NULL;
+		winctx->rx_fifo = 0;
 	}
 
 	winctx->lnotify_lpid = rxattr->lnotify_lpid;
@@ -1310,8 +1310,8 @@
 	/* if send window, drop reference to matching receive window */
 	if (window->tx_win) {
 		if (window->user_win) {
-			put_vas_user_win_ref(&vwin->task_ref);
 			mm_context_remove_vas_window(vwin->task_ref.mm);
+			put_vas_user_win_ref(&vwin->task_ref);
 		}
 		put_rx_win(window->rxwin);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/powernv/vas.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/powernv/vas.h
@@ -376,7 +376,7 @@
  * is a container for the register fields in the window context.
  */
 struct vas_winctx {
-	void *rx_fifo;
+	u64 rx_fifo;
 	int rx_fifo_size;
 	int wcreds_max;
 	int rsvd_txbuf_count;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/dtl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/dtl.c
@@ -181,7 +181,7 @@
 		return -EBUSY;
 
 	/* ensure there are no other conflicting dtl users */
-	if (!read_trylock(&dtl_access_lock))
+	if (!down_read_trylock(&dtl_access_lock))
 		return -EBUSY;
 
 	n_entries = dtl_buf_entries;
@@ -189,7 +189,7 @@
 	if (!buf) {
 		printk(KERN_WARNING "%s: buffer alloc failed for cpu %d\n",
 				__func__, dtl->cpu);
-		read_unlock(&dtl_access_lock);
+		up_read(&dtl_access_lock);
 		return -ENOMEM;
 	}
 
@@ -207,7 +207,7 @@
 	spin_unlock(&dtl->lock);
 
 	if (rc) {
-		read_unlock(&dtl_access_lock);
+		up_read(&dtl_access_lock);
 		kmem_cache_free(dtl_cache, buf);
 	}
 
@@ -222,7 +222,7 @@
 	dtl->buf = NULL;
 	dtl->buf_entries = 0;
 	spin_unlock(&dtl->lock);
-	read_unlock(&dtl_access_lock);
+	up_read(&dtl_access_lock);
 }
 
 /* file interface */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/eeh_pseries.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/eeh_pseries.c
@@ -578,8 +578,10 @@
 
 	switch(rets[0]) {
 	case 0:
-		result = EEH_STATE_MMIO_ACTIVE |
-			 EEH_STATE_DMA_ACTIVE;
+		result = EEH_STATE_MMIO_ACTIVE	|
+			 EEH_STATE_DMA_ACTIVE	|
+			 EEH_STATE_MMIO_ENABLED	|
+			 EEH_STATE_DMA_ENABLED;
 		break;
 	case 1:
 		result = EEH_STATE_RESET_ACTIVE |
@@ -845,18 +847,8 @@
 		return -EINVAL;
 	}
 
-	/* Initialize error log lock and size */
-	spin_lock_init(&slot_errbuf_lock);
-	eeh_error_buf_size = rtas_token("rtas-error-log-max");
-	if (eeh_error_buf_size == RTAS_UNKNOWN_SERVICE) {
-		pr_info("%s: unknown EEH error log size\n",
-			__func__);
-		eeh_error_buf_size = 1024;
-	} else if (eeh_error_buf_size > RTAS_ERROR_LOG_MAX) {
-		pr_info("%s: EEH error log size %d exceeds the maximal %d\n",
-			__func__, eeh_error_buf_size, RTAS_ERROR_LOG_MAX);
-		eeh_error_buf_size = RTAS_ERROR_LOG_MAX;
-	}
+	/* Initialize error log size */
+	eeh_error_buf_size = rtas_get_error_log_max();
 
 	/* Set EEH probe mode */
 	eeh_add_flag(EEH_PROBE_MODE_DEVTREE | EEH_ENABLE_IO_FOR_LOG);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/hotplug-memory.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/hotplug-memory.c
@@ -501,14 +501,15 @@
 		}
 	}
 
-	if (!lmb_found)
+	if (!lmb_found) {
+		pr_debug("Failed to look up LMB for drc index %x\n", drc_index);
 		rc = -EINVAL;
-
-	if (rc)
+	} else if (rc) {
 		pr_debug("Failed to hot-remove memory at %llx\n",
 			 lmb->base_addr);
-	else
+	} else {
 		pr_debug("Memory at %llx was hot-removed\n", lmb->base_addr);
+	}
 
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/ibmebus.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/ibmebus.c
@@ -451,6 +451,7 @@
 	if (err) {
 		printk(KERN_WARNING "%s: device_register returned %i\n",
 		       __func__, err);
+		put_device(&ibmebus_bus_device);
 		bus_unregister(&ibmebus_bus_type);
 
 		return err;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/iommu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/iommu.c
@@ -85,19 +85,24 @@
 static void iommu_pseries_free_group(struct iommu_table_group *table_group,
 		const char *node_name)
 {
-	struct iommu_table *tbl;
-
 	if (!table_group)
 		return;
 
-	tbl = table_group->tables[0];
 #ifdef CONFIG_IOMMU_API
 	if (table_group->group) {
 		iommu_group_put(table_group->group);
 		BUG_ON(table_group->group);
 	}
 #endif
-	iommu_tce_table_put(tbl);
+
+	/* Default DMA window table is at index 0, while DDW at 1. SR-IOV
+	 * adapters only have table on index 1.
+	 */
+	if (table_group->tables[0])
+		iommu_tce_table_put(table_group->tables[0]);
+
+	if (table_group->tables[1])
+		iommu_tce_table_put(table_group->tables[1]);
 
 	kfree(table_group);
 }
@@ -306,13 +311,22 @@
 static void tce_freemulti_pSeriesLP(struct iommu_table *tbl, long tcenum, long npages)
 {
 	u64 rc;
+	long rpages = npages;
+	unsigned long limit;
 
 	if (!firmware_has_feature(FW_FEATURE_STUFF_TCE))
 		return tce_free_pSeriesLP(tbl->it_index, tcenum,
 					  tbl->it_page_shift, npages);
 
-	rc = plpar_tce_stuff((u64)tbl->it_index,
-			     (u64)tcenum << tbl->it_page_shift, 0, npages);
+	do {
+		limit = min_t(unsigned long, rpages, 512);
+
+		rc = plpar_tce_stuff((u64)tbl->it_index,
+				     (u64)tcenum << tbl->it_page_shift, 0, limit);
+
+		rpages -= limit;
+		tcenum += limit;
+	} while (rpages > 0 && !rc);
 
 	if (rc && printk_ratelimit()) {
 		printk("tce_freemulti_pSeriesLP: plpar_tce_stuff failed\n");
@@ -1092,15 +1106,6 @@
 	phys_addr_t max_addr = memory_hotplug_max();
 	struct device_node *memory;
 
-	/*
-	 * The "ibm,pmemory" can appear anywhere in the address space.
-	 * Assuming it is still backed by page structs, set the upper limit
-	 * for the huge DMA window as MAX_PHYSMEM_BITS.
-	 */
-	if (of_find_node_by_type(NULL, "ibm,pmemory"))
-		return (sizeof(phys_addr_t) * 8 <= MAX_PHYSMEM_BITS) ?
-			(phys_addr_t) -1 : (1ULL << MAX_PHYSMEM_BITS);
-
 	for_each_node_by_type(memory, "memory") {
 		unsigned long start, size;
 		int n_mem_addr_cells, n_mem_size_cells, len;
@@ -1236,7 +1241,6 @@
 	u32 ddw_avail[DDW_APPLICABLE_SIZE];
 	struct dma_win *window;
 	struct property *win64;
-	bool ddw_enabled = false;
 	struct failed_ddw_pdn *fpdn;
 	bool default_win_removed = false, direct_mapping = false;
 	bool pmem_present;
@@ -1251,7 +1255,6 @@
 
 	if (find_existing_ddw(pdn, &dev->dev.archdata.dma_offset, &len)) {
 		direct_mapping = (len >= max_ram_len);
-		ddw_enabled = true;
 		goto out_unlock;
 	}
 
@@ -1365,8 +1368,10 @@
 		len = order_base_2(query.largest_available_block << page_shift);
 		win_name = DMA64_PROPNAME;
 	} else {
-		direct_mapping = true;
-		win_name = DIRECT64_PROPNAME;
+		direct_mapping = !default_win_removed ||
+			(len == MAX_PHYSMEM_BITS) ||
+			(!pmem_present && (len == max_ram_len));
+		win_name = direct_mapping ? DIRECT64_PROPNAME : DMA64_PROPNAME;
 	}
 
 	ret = create_ddw(dev, ddw_avail, &create, page_shift, len);
@@ -1404,8 +1409,8 @@
 			dev_info(&dev->dev, "failed to map DMA window for %pOF: %d\n",
 				 dn, ret);
 
-		/* Make sure to clean DDW if any TCE was set*/
-		clean_dma_window(pdn, win64->value);
+			/* Make sure to clean DDW if any TCE was set*/
+			clean_dma_window(pdn, win64->value);
 			goto out_del_list;
 		}
 	} else {
@@ -1452,7 +1457,6 @@
 	spin_unlock(&dma_win_list_lock);
 
 	dev->dev.archdata.dma_offset = win_addr;
-	ddw_enabled = true;
 	goto out_unlock;
 
 out_del_list:
@@ -1488,10 +1492,10 @@
 	 * as RAM, then we failed to create a window to cover persistent
 	 * memory and need to set the DMA limit.
 	 */
-	if (pmem_present && ddw_enabled && direct_mapping && len == max_ram_len)
+	if (pmem_present && direct_mapping && len == max_ram_len)
 		dev->dev.bus_dma_limit = dev->dev.archdata.dma_offset + (1ULL << len);
 
-    return ddw_enabled && direct_mapping;
+	return direct_mapping;
 }
 
 static void pci_dma_dev_setup_pSeriesLP(struct pci_dev *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/lpar.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/lpar.c
@@ -167,7 +167,7 @@
  */
 #define NR_CPUS_H	NR_CPUS
 
-DEFINE_RWLOCK(dtl_access_lock);
+DECLARE_RWSEM(dtl_access_lock);
 static DEFINE_PER_CPU(struct vcpu_dispatch_data, vcpu_disp_data);
 static DEFINE_PER_CPU(u64, dtl_entry_ridx);
 static DEFINE_PER_CPU(struct dtl_worker, dtl_workers);
@@ -461,7 +461,7 @@
 {
 	int rc = 0, state;
 
-	if (!write_trylock(&dtl_access_lock)) {
+	if (!down_write_trylock(&dtl_access_lock)) {
 		rc = -EBUSY;
 		goto out;
 	}
@@ -477,7 +477,7 @@
 		pr_err("vcpudispatch_stats: unable to setup workqueue for DTL processing\n");
 		free_dtl_buffers(time_limit);
 		reset_global_dtl_mask();
-		write_unlock(&dtl_access_lock);
+		up_write(&dtl_access_lock);
 		rc = -EINVAL;
 		goto out;
 	}
@@ -492,7 +492,7 @@
 	cpuhp_remove_state(dtl_worker_state);
 	free_dtl_buffers(time_limit);
 	reset_global_dtl_mask();
-	write_unlock(&dtl_access_lock);
+	up_write(&dtl_access_lock);
 }
 
 static ssize_t vcpudispatch_stats_write(struct file *file, const char __user *p,
@@ -524,8 +524,10 @@
 
 	if (cmd) {
 		rc = init_cpu_associativity();
-		if (rc)
+		if (rc) {
+			destroy_cpu_associativity();
 			goto out;
+		}
 
 		for_each_possible_cpu(cpu) {
 			disp = per_cpu_ptr(&vcpu_disp_data, cpu);
@@ -638,16 +640,8 @@
 
 static int __init vcpudispatch_stats_procfs_init(void)
 {
-	/*
-	 * Avoid smp_processor_id while preemptible. All CPUs should have
-	 * the same value for lppaca_shared_proc.
-	 */
-	preempt_disable();
-	if (!lppaca_shared_proc(get_lppaca())) {
-		preempt_enable();
+	if (!lppaca_shared_proc())
 		return 0;
-	}
-	preempt_enable();
 
 	if (!proc_create("powerpc/vcpudispatch_stats", 0600, NULL,
 					&vcpudispatch_stats_proc_ops))
@@ -1440,22 +1434,22 @@
 
 void __init pseries_lpar_read_hblkrm_characteristics(void)
 {
+	const s32 token = rtas_token("ibm,get-system-parameter");
 	unsigned char local_buffer[SPLPAR_TLB_BIC_MAXLENGTH];
 	int call_status, len, idx, bpsize;
 
 	if (!firmware_has_feature(FW_FEATURE_BLOCK_REMOVE))
 		return;
 
-	spin_lock(&rtas_data_buf_lock);
-	memset(rtas_data_buf, 0, RTAS_DATA_BUF_SIZE);
-	call_status = rtas_call(rtas_token("ibm,get-system-parameter"), 3, 1,
-				NULL,
-				SPLPAR_TLB_BIC_TOKEN,
-				__pa(rtas_data_buf),
-				RTAS_DATA_BUF_SIZE);
-	memcpy(local_buffer, rtas_data_buf, SPLPAR_TLB_BIC_MAXLENGTH);
-	local_buffer[SPLPAR_TLB_BIC_MAXLENGTH - 1] = '\0';
-	spin_unlock(&rtas_data_buf_lock);
+	do {
+		spin_lock(&rtas_data_buf_lock);
+		memset(rtas_data_buf, 0, RTAS_DATA_BUF_SIZE);
+		call_status = rtas_call(token, 3, 1, NULL, SPLPAR_TLB_BIC_TOKEN,
+					__pa(rtas_data_buf), RTAS_DATA_BUF_SIZE);
+		memcpy(local_buffer, rtas_data_buf, SPLPAR_TLB_BIC_MAXLENGTH);
+		local_buffer[SPLPAR_TLB_BIC_MAXLENGTH - 1] = '\0';
+		spin_unlock(&rtas_data_buf_lock);
+	} while (rtas_busy_delay(call_status));
 
 	if (call_status != 0) {
 		pr_warn("%s %s Error calling get-system-parameter (0x%x)\n",
@@ -1892,10 +1886,10 @@
  * h_get_mpp
  * H_GET_MPP hcall returns info in 7 parms
  */
-int h_get_mpp(struct hvcall_mpp_data *mpp_data)
+long h_get_mpp(struct hvcall_mpp_data *mpp_data)
 {
-	int rc;
-	unsigned long retbuf[PLPAR_HCALL9_BUFSIZE];
+	unsigned long retbuf[PLPAR_HCALL9_BUFSIZE] = {0};
+	long rc;
 
 	rc = plpar_hcall9(H_GET_MPP, retbuf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/lparcfg.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/lparcfg.c
@@ -112,8 +112,8 @@
  */
 static unsigned int h_get_ppp(struct hvcall_ppp_data *ppp_data)
 {
-	unsigned long rc;
-	unsigned long retbuf[PLPAR_HCALL9_BUFSIZE];
+	unsigned long retbuf[PLPAR_HCALL9_BUFSIZE] = {0};
+	long rc;
 
 	rc = plpar_hcall9(H_GET_PPP, retbuf);
 
@@ -192,7 +192,7 @@
 	struct hvcall_ppp_data ppp_data;
 	struct device_node *root;
 	const __be32 *perf_level;
-	int rc;
+	long rc;
 
 	rc = h_get_ppp(&ppp_data);
 	if (rc)
@@ -205,7 +205,7 @@
 	           ppp_data.active_system_procs);
 
 	/* pool related entries are appropriate for shared configs */
-	if (lppaca_shared_proc(get_lppaca())) {
+	if (lppaca_shared_proc()) {
 		unsigned long pool_idle_time, pool_procs;
 
 		seq_printf(m, "pool=%d\n", ppp_data.pool_num);
@@ -322,6 +322,7 @@
  */
 static void parse_system_parameter_string(struct seq_file *m)
 {
+	const s32 token = rtas_token("ibm,get-system-parameter");
 	int call_status;
 
 	unsigned char *local_buffer = kmalloc(SPLPAR_MAXLENGTH, GFP_KERNEL);
@@ -331,16 +332,15 @@
 		return;
 	}
 
-	spin_lock(&rtas_data_buf_lock);
-	memset(rtas_data_buf, 0, SPLPAR_MAXLENGTH);
-	call_status = rtas_call(rtas_token("ibm,get-system-parameter"), 3, 1,
-				NULL,
-				SPLPAR_CHARACTERISTICS_TOKEN,
-				__pa(rtas_data_buf),
-				RTAS_DATA_BUF_SIZE);
-	memcpy(local_buffer, rtas_data_buf, SPLPAR_MAXLENGTH);
-	local_buffer[SPLPAR_MAXLENGTH - 1] = '\0';
-	spin_unlock(&rtas_data_buf_lock);
+	do {
+		spin_lock(&rtas_data_buf_lock);
+		memset(rtas_data_buf, 0, SPLPAR_MAXLENGTH);
+		call_status = rtas_call(token, 3, 1, NULL, SPLPAR_CHARACTERISTICS_TOKEN,
+					__pa(rtas_data_buf), RTAS_DATA_BUF_SIZE);
+		memcpy(local_buffer, rtas_data_buf, SPLPAR_MAXLENGTH);
+		local_buffer[SPLPAR_MAXLENGTH - 1] = '\0';
+		spin_unlock(&rtas_data_buf_lock);
+	} while (rtas_busy_delay(call_status));
 
 	if (call_status != 0) {
 		printk(KERN_INFO
@@ -529,7 +529,7 @@
 		   partition_potential_processors);
 
 	seq_printf(m, "shared_processor_mode=%d\n",
-		   lppaca_shared_proc(get_lppaca()));
+		   lppaca_shared_proc());
 
 #ifdef CONFIG_PPC_BOOK3S_64
 	seq_printf(m, "slb_size=%d\n", mmu_slb_size);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/mobility.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/mobility.c
@@ -63,6 +63,27 @@
 
 static int delete_dt_node(struct device_node *dn)
 {
+	struct device_node *pdn;
+	bool is_platfac;
+
+	pdn = of_get_parent(dn);
+	is_platfac = of_node_is_type(dn, "ibm,platform-facilities") ||
+		     of_node_is_type(pdn, "ibm,platform-facilities");
+	of_node_put(pdn);
+
+	/*
+	 * The drivers that bind to nodes in the platform-facilities
+	 * hierarchy don't support node removal, and the removal directive
+	 * from firmware is always followed by an add of an equivalent
+	 * node. The capability (e.g. RNG, encryption, compression)
+	 * represented by the node is never interrupted by the migration.
+	 * So ignore changes to this part of the tree.
+	 */
+	if (is_platfac) {
+		pr_notice("ignoring remove operation for %pOFfp\n", dn);
+		return 0;
+	}
+
 	pr_debug("removing node %pOFfp\n", dn);
 	dlpar_detach_node(dn);
 	return 0;
@@ -222,6 +243,19 @@
 	if (!dn)
 		return -ENOENT;
 
+	/*
+	 * Since delete_dt_node() ignores this node type, this is the
+	 * necessary counterpart. We also know that a platform-facilities
+	 * node returned from dlpar_configure_connector() has children
+	 * attached, and dlpar_attach_node() only adds the parent, leaking
+	 * the children. So ignore these on the add side for now.
+	 */
+	if (of_node_is_type(dn, "ibm,platform-facilities")) {
+		pr_notice("ignoring add operation for %pOF\n", dn);
+		dlpar_free_cc_nodes(dn);
+		return 0;
+	}
+
 	rc = dlpar_attach_node(dn, parent_dn);
 	if (rc)
 		dlpar_free_cc_nodes(dn);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/papr_scm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/papr_scm.c
@@ -1159,6 +1159,13 @@
 		return -ENODEV;
 	}
 
+	/*
+	 * open firmware platform device create won't update the NUMA 
+	 * distance table. For PAPR SCM devices we use numa_map_to_online_node()
+	 * to find the nearest online NUMA node and that requires correct
+	 * distance table information.
+	 */
+	update_numa_distance(dn);
 
 	p = kzalloc(sizeof(*p), GFP_KERNEL);
 	if (!p)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/pci_dlpar.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/pci_dlpar.c
@@ -78,6 +78,9 @@
 
 	pseries_msi_free_domains(phb);
 
+	/* Keep a reference so phb isn't freed yet */
+	get_device(&host_bridge->dev);
+
 	/* Remove the PCI bus and unregister the bridge device from sysfs */
 	phb->bus = NULL;
 	pci_remove_bus(b);
@@ -101,6 +104,7 @@
 	 * the pcibios_free_controller_deferred() callback;
 	 * see pseries_root_bridge_prepare().
 	 */
+	put_device(&host_bridge->dev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/pseries.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/pseries.h
@@ -115,4 +115,6 @@
 void pseries_setup_security_mitigations(void);
 void pseries_lpar_read_hblkrm_characteristics(void);
 
+void pseries_rng_init(void);
+
 #endif /* _PSERIES_PSERIES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/rng.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/rng.c
@@ -10,6 +10,7 @@
 #include <asm/archrandom.h>
 #include <asm/machdep.h>
 #include <asm/plpar_wrappers.h>
+#include "pseries.h"
 
 
 static int pseries_get_random_long(unsigned long *v)
@@ -24,19 +25,13 @@
 	return 0;
 }
 
-static __init int rng_init(void)
+void __init pseries_rng_init(void)
 {
 	struct device_node *dn;
 
 	dn = of_find_compatible_node(NULL, NULL, "ibm,random");
 	if (!dn)
-		return -ENODEV;
-
-	pr_info("Registering arch random hook.\n");
-
+		return;
 	ppc_md.get_random_seed = pseries_get_random_long;
-
 	of_node_put(dn);
-	return 0;
 }
-machine_subsys_initcall(pseries, rng_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/setup.c
@@ -314,8 +314,8 @@
 {
 	void (*ctor)(void *) = get_dtl_cache_ctor();
 
-	dtl_cache = kmem_cache_create("dtl", DISPATCH_LOG_BYTES,
-						DISPATCH_LOG_BYTES, 0, ctor);
+	dtl_cache = kmem_cache_create_usercopy("dtl", DISPATCH_LOG_BYTES,
+						DISPATCH_LOG_BYTES, 0, 0, DISPATCH_LOG_BYTES, ctor);
 	if (!dtl_cache) {
 		pr_warn("Failed to create dispatch trace log buffer cache\n");
 		pr_warn("Stolen time statistics will be unreliable\n");
@@ -411,16 +411,6 @@
 }
 EXPORT_SYMBOL(pseries_disable_reloc_on_exc);
 
-#ifdef CONFIG_KEXEC_CORE
-static void pSeries_machine_kexec(struct kimage *image)
-{
-	if (firmware_has_feature(FW_FEATURE_SET_MODE))
-		pseries_disable_reloc_on_exc();
-
-	default_machine_kexec(image);
-}
-#endif
-
 #ifdef __LITTLE_ENDIAN__
 void pseries_big_endian_exceptions(void)
 {
@@ -816,7 +806,7 @@
 	if (firmware_has_feature(FW_FEATURE_LPAR)) {
 		vpa_init(boot_cpuid);
 
-		if (lppaca_shared_proc(get_lppaca())) {
+		if (lppaca_shared_proc()) {
 			static_branch_enable(&shared_processor);
 			pv_spinlocks_init();
 		}
@@ -840,6 +830,8 @@
 
 	if (swiotlb_force == SWIOTLB_FORCE)
 		ppc_swiotlb_enable = 1;
+
+	pseries_rng_init();
 }
 
 static void pseries_panic(char *str)
@@ -1086,7 +1078,6 @@
 	.machine_check_early	= pseries_machine_check_realmode,
 	.machine_check_exception = pSeries_machine_check_exception,
 #ifdef CONFIG_KEXEC_CORE
-	.machine_kexec          = pSeries_machine_kexec,
 	.kexec_cpu_down         = pseries_kexec_cpu_down,
 #endif
 #ifdef CONFIG_MEMORY_HOTPLUG_SPARSE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/svm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/svm.c
@@ -56,8 +56,7 @@
 		return;
 
 
-	memblock_free_early(__pa(vstart),
-			    PAGE_ALIGN(io_tlb_nslabs << IO_TLB_SHIFT));
+	memblock_free(__pa(vstart), PAGE_ALIGN(io_tlb_nslabs << IO_TLB_SHIFT));
 	panic("SVM: Cannot allocate SWIOTLB buffer");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/vas.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/vas.c
@@ -324,7 +324,7 @@
 		 * So no unpacking needs to be done.
 		 */
 		rc = plpar_hcall9(H_HOME_NODE_ASSOCIATIVITY, domain,
-				  VPHN_FLAG_VCPU, smp_processor_id());
+				  VPHN_FLAG_VCPU, hard_smp_processor_id());
 		if (rc != H_SUCCESS) {
 			pr_err("H_HOME_NODE_ASSOCIATIVITY error: %d\n", rc);
 			goto out;
@@ -441,8 +441,8 @@
 	atomic_dec(&caps->used_lpar_creds);
 	mutex_unlock(&vas_pseries_mutex);
 
-	put_vas_user_win_ref(&vwin->task_ref);
 	mm_context_remove_vas_window(vwin->task_ref.mm);
+	put_vas_user_win_ref(&vwin->task_ref);
 
 	kfree(win);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/platforms/pseries/vio.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/platforms/pseries/vio.c
@@ -38,7 +38,6 @@
 	.name = "vio",
 	.type = "",
 	.dev.init_name = "vio",
-	.dev.bus = &vio_bus_type,
 };
 
 #ifdef CONFIG_PPC_SMLPAR
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/purgatory/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/purgatory/Makefile
@@ -4,6 +4,11 @@
 
 targets += trampoline_$(BITS).o purgatory.ro kexec-purgatory.c
 
+# When profile-guided optimization is enabled, llvm emits two different
+# overlapping text sections, which is not supported by kexec. Remove profile
+# optimization flags.
+KBUILD_CFLAGS := $(filter-out -fprofile-sample-use=% -fprofile-use=%,$(KBUILD_CFLAGS))
+
 LDFLAGS_purgatory.ro := -e purgatory_start -r --no-undefined
 
 $(obj)/purgatory.ro: $(obj)/trampoline_$(BITS).o FORCE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/dart_iommu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/dart_iommu.c
@@ -404,9 +404,10 @@
 	}
 
 	/* Initialize the DART HW */
-	if (dart_init(dn) != 0)
+	if (dart_init(dn) != 0) {
+		of_node_put(dn);
 		return;
-
+	}
 	/*
 	 * U4 supports a DART bypass, we use it for 64-bit capable devices to
 	 * improve performance.  However, that only works for devices connected
@@ -419,6 +420,7 @@
 
 	/* Setup pci_dma ops */
 	set_pci_dma_ops(&dma_iommu_ops);
+	of_node_put(dn);
 }
 
 #ifdef CONFIG_PM
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/dcr-low.S
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/dcr-low.S
@@ -11,7 +11,7 @@
 #include <asm/export.h>
 
 #define DCR_ACCESS_PROLOG(table) \
-	cmpli	cr0,r3,1024;	 \
+	cmplwi	cr0,r3,1024;	 \
 	rlwinm  r3,r3,4,18,27;   \
 	lis     r5,table@h;      \
 	ori     r5,r5,table@l;   \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/fsl_gtm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/fsl_gtm.c
@@ -86,7 +86,7 @@
  */
 struct gtm_timer *gtm_get_timer16(void)
 {
-	struct gtm *gtm = NULL;
+	struct gtm *gtm;
 	int i;
 
 	list_for_each_entry(gtm, &gtms, list_node) {
@@ -103,7 +103,7 @@
 		spin_unlock_irq(&gtm->lock);
 	}
 
-	if (gtm)
+	if (!list_empty(&gtms))
 		return ERR_PTR(-EBUSY);
 	return ERR_PTR(-ENODEV);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/fsl_msi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/fsl_msi.c
@@ -211,8 +211,10 @@
 			dev_err(&pdev->dev,
 				"node %pOF has an invalid fsl,msi phandle %u\n",
 				hose->dn, np->phandle);
+			of_node_put(np);
 			return -EINVAL;
 		}
+		of_node_put(np);
 	}
 
 	for_each_pci_msi_entry(entry, pdev) {
@@ -567,10 +569,12 @@
 	.msiir_offset = 0x38,
 };
 
+#ifdef CONFIG_EPAPR_PARAVIRT
 static const struct fsl_msi_feature vmpic_msi_feature = {
 	.fsl_pic_ip = FSL_PIC_IP_VMPIC,
 	.msiir_offset = 0,
 };
+#endif
 
 static const struct of_device_id fsl_of_msi_ids[] = {
 	{
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/fsl_pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/fsl_pci.c
@@ -520,6 +520,7 @@
 	struct resource rsrc;
 	const int *bus_range;
 	u8 hdr_type, progif;
+	u32 class_code;
 	struct device_node *dev;
 	struct ccsr_pci __iomem *pci;
 	u16 temp;
@@ -593,6 +594,13 @@
 			PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS;
 		if (fsl_pcie_check_link(hose))
 			hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK;
+		/* Fix Class Code to PCI_CLASS_BRIDGE_PCI_NORMAL for pre-3.0 controller */
+		if (in_be32(&pci->block_rev1) < PCIE_IP_REV_3_0) {
+			early_read_config_dword(hose, 0, 0, PCIE_FSL_CSR_CLASSCODE, &class_code);
+			class_code &= 0xff;
+			class_code |= PCI_CLASS_BRIDGE_PCI_NORMAL << 8;
+			early_write_config_dword(hose, 0, 0, PCIE_FSL_CSR_CLASSCODE, class_code);
+		}
 	} else {
 		/*
 		 * Set PBFR(PCI Bus Function Register)[10] = 1 to
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/fsl_pci.h
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/fsl_pci.h
@@ -18,6 +18,7 @@
 
 #define PCIE_LTSSM	0x0404		/* PCIE Link Training and Status */
 #define PCIE_LTSSM_L0	0x16		/* L0 state */
+#define PCIE_FSL_CSR_CLASSCODE	0x474	/* FSL GPEX CSR */
 #define PCIE_IP_REV_2_2		0x02080202 /* PCIE IP block version Rev2.2 */
 #define PCIE_IP_REV_3_0		0x02080300 /* PCIE IP block version Rev3.0 */
 #define PIWAR_EN		0x80000000	/* Enable */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/fsl_rio.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/fsl_rio.c
@@ -505,8 +505,10 @@
 	if (rc) {
 		dev_err(&dev->dev, "Can't get %pOF property 'reg'\n",
 				rmu_node);
+		of_node_put(rmu_node);
 		goto err_rmu;
 	}
+	of_node_put(rmu_node);
 	rmu_regs_win = ioremap(rmu_regs.start, resource_size(&rmu_regs));
 	if (!rmu_regs_win) {
 		dev_err(&dev->dev, "Unable to map rmu register window\n");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/tsi108_pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/tsi108_pci.c
@@ -216,9 +216,8 @@
 
 	(hose)->ops = &tsi108_direct_pci_ops;
 
-	printk(KERN_INFO "Found tsi108 PCI host bridge at 0x%08x. "
-	       "Firmware bus number: %d->%d\n",
-	       rsrc.start, hose->first_busno, hose->last_busno);
+	pr_info("Found tsi108 PCI host bridge at 0x%pa. Firmware bus number: %d->%d\n",
+		&rsrc.start, hose->first_busno, hose->last_busno);
 
 	/* Interpret the "ranges" property */
 	/* This also maps the I/O region and sets isa_io/mem_base */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xics/icp-native.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xics/icp-native.c
@@ -235,6 +235,8 @@
 	rname = kasprintf(GFP_KERNEL, "CPU %d [0x%x] Interrupt Presentation",
 			  cpu, hw_id);
 
+	if (!rname)
+		return -ENOMEM;
 	if (!request_mem_region(addr, size, rname)) {
 		pr_warn("icp_native: Could not reserve ICP MMIO for CPU %d, interrupt server #0x%x\n",
 			cpu, hw_id);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xics/icp-opal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xics/icp-opal.c
@@ -196,6 +196,7 @@
 
 	printk("XICS: Using OPAL ICP fallbacks\n");
 
+	of_node_put(np);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xics/ics-rtas.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xics/ics-rtas.c
@@ -37,8 +37,8 @@
 
 	server = xics_get_irq_server(d->irq, irq_data_get_affinity_mask(d), 0);
 
-	call_status = rtas_call_reentrant(ibm_set_xive, 3, 1, NULL, hw_irq,
-					  server, DEFAULT_PRIORITY);
+	call_status = rtas_call(ibm_set_xive, 3, 1, NULL, hw_irq, server,
+				DEFAULT_PRIORITY);
 	if (call_status != 0) {
 		printk(KERN_ERR
 			"%s: ibm_set_xive irq %u server %x returned %d\n",
@@ -47,7 +47,7 @@
 	}
 
 	/* Now unmask the interrupt (often a no-op) */
-	call_status = rtas_call_reentrant(ibm_int_on, 1, 1, NULL, hw_irq);
+	call_status = rtas_call(ibm_int_on, 1, 1, NULL, hw_irq);
 	if (call_status != 0) {
 		printk(KERN_ERR "%s: ibm_int_on irq=%u returned %d\n",
 			__func__, hw_irq, call_status);
@@ -69,7 +69,7 @@
 	if (hw_irq == XICS_IPI)
 		return;
 
-	call_status = rtas_call_reentrant(ibm_int_off, 1, 1, NULL, hw_irq);
+	call_status = rtas_call(ibm_int_off, 1, 1, NULL, hw_irq);
 	if (call_status != 0) {
 		printk(KERN_ERR "%s: ibm_int_off irq=%u returned %d\n",
 			__func__, hw_irq, call_status);
@@ -77,8 +77,8 @@
 	}
 
 	/* Have to set XIVE to 0xff to be able to remove a slot */
-	call_status = rtas_call_reentrant(ibm_set_xive, 3, 1, NULL, hw_irq,
-					  xics_default_server, 0xff);
+	call_status = rtas_call(ibm_set_xive, 3, 1, NULL, hw_irq,
+				xics_default_server, 0xff);
 	if (call_status != 0) {
 		printk(KERN_ERR "%s: ibm_set_xive(0xff) irq=%u returned %d\n",
 			__func__, hw_irq, call_status);
@@ -109,7 +109,7 @@
 	if (hw_irq == XICS_IPI || hw_irq == XICS_IRQ_SPURIOUS)
 		return -1;
 
-	status = rtas_call_reentrant(ibm_get_xive, 1, 3, xics_status, hw_irq);
+	status = rtas_call(ibm_get_xive, 1, 3, xics_status, hw_irq);
 
 	if (status) {
 		printk(KERN_ERR "%s: ibm,get-xive irq=%u returns %d\n",
@@ -127,8 +127,8 @@
 	pr_debug("%s: irq %d [hw 0x%x] server: 0x%x\n", __func__, d->irq,
 		 hw_irq, irq_server);
 
-	status = rtas_call_reentrant(ibm_set_xive, 3, 1, NULL,
-				     hw_irq, irq_server, xics_status[1]);
+	status = rtas_call(ibm_set_xive, 3, 1, NULL,
+			   hw_irq, irq_server, xics_status[1]);
 
 	if (status) {
 		printk(KERN_ERR "%s: ibm,set-xive irq=%u returns %d\n",
@@ -159,7 +159,7 @@
 		return -EINVAL;
 
 	/* Check if RTAS knows about this interrupt */
-	rc = rtas_call_reentrant(ibm_get_xive, 1, 3, status, hw_irq);
+	rc = rtas_call(ibm_get_xive, 1, 3, status, hw_irq);
 	if (rc)
 		return -ENXIO;
 
@@ -175,7 +175,7 @@
 {
 	int rc, status[2];
 
-	rc = rtas_call_reentrant(ibm_get_xive, 1, 3, status, vec);
+	rc = rtas_call(ibm_get_xive, 1, 3, status, vec);
 	if (rc)
 		return -1;
 	return status[0];
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xive/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xive/Kconfig
@@ -3,7 +3,6 @@
 	bool
 	select PPC_SMP_MUXED_IPI
 	select HARDIRQS_SW_RESEND
-	select IRQ_DOMAIN_NOMAP
 
 config PPC_XIVE_NATIVE
 	bool
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xive/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xive/common.c
@@ -1443,8 +1443,7 @@
 
 static void __init xive_init_host(struct device_node *np)
 {
-	xive_irq_domain = irq_domain_add_nomap(np, XIVE_MAX_IRQ,
-					       &xive_irq_domain_ops, NULL);
+	xive_irq_domain = irq_domain_add_tree(np, &xive_irq_domain_ops, NULL);
 	if (WARN_ON(xive_irq_domain == NULL))
 		return;
 	irq_set_default_host(xive_irq_domain);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xive/native.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xive/native.c
@@ -786,7 +786,7 @@
 	if (out_qpage)
 		*out_qpage = be64_to_cpu(qpage);
 	if (out_qsize)
-		*out_qsize = be32_to_cpu(qsize);
+		*out_qsize = be64_to_cpu(qsize);
 	if (out_qeoi_page)
 		*out_qeoi_page = be64_to_cpu(qeoi_page);
 	if (out_escalate_irq)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/sysdev/xive/spapr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/sysdev/xive/spapr.c
@@ -13,6 +13,7 @@
 #include <linux/of.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/bitmap.h>
 #include <linux/cpumask.h>
 #include <linux/mm.h>
 #include <linux/delay.h>
@@ -55,7 +56,7 @@
 	spin_lock_init(&xibm->lock);
 	xibm->base = base;
 	xibm->count = count;
-	xibm->bitmap = kzalloc(xibm->count, GFP_KERNEL);
+	xibm->bitmap = bitmap_zalloc(xibm->count, GFP_KERNEL);
 	if (!xibm->bitmap) {
 		kfree(xibm);
 		return -ENOMEM;
@@ -67,6 +68,17 @@
 	return 0;
 }
 
+static void xive_irq_bitmap_remove_all(void)
+{
+	struct xive_irq_bitmap *xibm, *tmp;
+
+	list_for_each_entry_safe(xibm, tmp, &xive_irq_bitmaps, list) {
+		list_del(&xibm->list);
+		bitmap_free(xibm->bitmap);
+		kfree(xibm);
+	}
+}
+
 static int __xive_irq_bitmap_alloc(struct xive_irq_bitmap *xibm)
 {
 	int irq;
@@ -425,6 +437,7 @@
 
 	data->trig_mmio = ioremap(data->trig_page, 1u << data->esb_shift);
 	if (!data->trig_mmio) {
+		iounmap(data->eoi_mmio);
 		pr_err("Failed to map trigger page for irq 0x%x\n", hw_irq);
 		return -ENOMEM;
 	}
@@ -653,6 +666,9 @@
 	struct xive_irq_bitmap *xibm;
 	char *buf = kmalloc(PAGE_SIZE, GFP_KERNEL);
 
+	if (!buf)
+		return -ENOMEM;
+
 	list_for_each_entry(xibm, &xive_irq_bitmaps, list) {
 		memset(buf, 0, PAGE_SIZE);
 		bitmap_print_to_pagebuf(true, buf, xibm->bitmap, xibm->count);
@@ -701,6 +717,7 @@
 	}
 
 	reg = of_get_property(rootdn, "ibm,plat-res-int-priorities", &len);
+	of_node_put(rootdn);
 	if (!reg) {
 		pr_err("Failed to read 'ibm,plat-res-int-priorities' property\n");
 		return false;
@@ -800,7 +817,7 @@
 	u32 val;
 	u32 len;
 	const __be32 *reg;
-	int i;
+	int i, err;
 
 	if (xive_spapr_disabled())
 		return false;
@@ -816,32 +833,35 @@
 	/* Resource 1 is the OS ring TIMA */
 	if (of_address_to_resource(np, 1, &r)) {
 		pr_err("Failed to get thread mgmnt area resource\n");
-		return false;
+		goto err_put;
 	}
 	tima = ioremap(r.start, resource_size(&r));
 	if (!tima) {
 		pr_err("Failed to map thread mgmnt area\n");
-		return false;
+		goto err_put;
 	}
 
 	if (!xive_get_max_prio(&max_prio))
-		return false;
+		goto err_unmap;
 
 	/* Feed the IRQ number allocator with the ranges given in the DT */
 	reg = of_get_property(np, "ibm,xive-lisn-ranges", &len);
 	if (!reg) {
 		pr_err("Failed to read 'ibm,xive-lisn-ranges' property\n");
-		return false;
+		goto err_unmap;
 	}
 
 	if (len % (2 * sizeof(u32)) != 0) {
 		pr_err("invalid 'ibm,xive-lisn-ranges' property\n");
-		return false;
+		goto err_unmap;
 	}
 
-	for (i = 0; i < len / (2 * sizeof(u32)); i++, reg += 2)
-		xive_irq_bitmap_add(be32_to_cpu(reg[0]),
-				    be32_to_cpu(reg[1]));
+	for (i = 0; i < len / (2 * sizeof(u32)); i++, reg += 2) {
+		err = xive_irq_bitmap_add(be32_to_cpu(reg[0]),
+					  be32_to_cpu(reg[1]));
+		if (err < 0)
+			goto err_mem_free;
+	}
 
 	/* Iterate the EQ sizes and pick one */
 	of_property_for_each_u32(np, "ibm,xive-eq-sizes", prop, reg, val) {
@@ -852,10 +872,19 @@
 
 	/* Initialize XIVE core with our backend */
 	if (!xive_core_init(np, &xive_spapr_ops, tima, TM_QW1_OS, max_prio))
-		return false;
+		goto err_mem_free;
 
+	of_node_put(np);
 	pr_info("Using %dkB queues\n", 1 << (xive_queue_shift - 10));
 	return true;
+
+err_mem_free:
+	xive_irq_bitmap_remove_all();
+err_unmap:
+	iounmap(tima);
+err_put:
+	of_node_put(np);
+	return false;
 }
 
 machine_arch_initcall(pseries, xive_core_debug_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/tools/relocs_check.sh
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/tools/relocs_check.sh
@@ -39,6 +39,7 @@
 	#	R_PPC_NONE
 	grep -F -w -v 'R_PPC64_RELATIVE
 R_PPC64_NONE
+R_PPC64_UADDR64
 R_PPC_ADDR16_LO
 R_PPC_ADDR16_HI
 R_PPC_ADDR16_HA
@@ -54,9 +55,3 @@
 num_bad=$(echo "$bad_relocs" | wc -l)
 echo "WARNING: $num_bad bad relocations"
 echo "$bad_relocs"
-
-# If we see this type of relocation it's an idication that
-# we /may/ be using an old version of binutils.
-if echo "$bad_relocs" | grep -q -F -w R_PPC64_UADDR64; then
-	echo "WARNING: You need at least binutils >= 2.19 to build a CONFIG_RELOCATABLE kernel"
-fi
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/xmon/ppc-dis.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/xmon/ppc-dis.c
@@ -122,32 +122,21 @@
   bool insn_is_short;
   ppc_cpu_t dialect;
 
-  dialect = PPC_OPCODE_PPC | PPC_OPCODE_COMMON
-            | PPC_OPCODE_64 | PPC_OPCODE_POWER4 | PPC_OPCODE_ALTIVEC;
+  dialect = PPC_OPCODE_PPC | PPC_OPCODE_COMMON;
 
-  if (cpu_has_feature(CPU_FTRS_POWER5))
-    dialect |= PPC_OPCODE_POWER5;
+  if (IS_ENABLED(CONFIG_PPC64))
+    dialect |= PPC_OPCODE_64 | PPC_OPCODE_POWER4 | PPC_OPCODE_CELL |
+	PPC_OPCODE_POWER5 | PPC_OPCODE_POWER6 | PPC_OPCODE_POWER7 | PPC_OPCODE_POWER8 |
+	PPC_OPCODE_POWER9;
 
-  if (cpu_has_feature(CPU_FTRS_CELL))
-    dialect |= (PPC_OPCODE_CELL | PPC_OPCODE_ALTIVEC);
+  if (cpu_has_feature(CPU_FTR_TM))
+    dialect |= PPC_OPCODE_HTM;
 
-  if (cpu_has_feature(CPU_FTRS_POWER6))
-    dialect |= (PPC_OPCODE_POWER5 | PPC_OPCODE_POWER6 | PPC_OPCODE_ALTIVEC);
-
-  if (cpu_has_feature(CPU_FTRS_POWER7))
-    dialect |= (PPC_OPCODE_POWER5 | PPC_OPCODE_POWER6 | PPC_OPCODE_POWER7
-                | PPC_OPCODE_ALTIVEC | PPC_OPCODE_VSX);
-
-  if (cpu_has_feature(CPU_FTRS_POWER8))
-    dialect |= (PPC_OPCODE_POWER5 | PPC_OPCODE_POWER6 | PPC_OPCODE_POWER7
-		| PPC_OPCODE_POWER8 | PPC_OPCODE_HTM
-		| PPC_OPCODE_ALTIVEC | PPC_OPCODE_ALTIVEC2 | PPC_OPCODE_VSX);
-
-  if (cpu_has_feature(CPU_FTRS_POWER9))
-    dialect |= (PPC_OPCODE_POWER5 | PPC_OPCODE_POWER6 | PPC_OPCODE_POWER7
-		| PPC_OPCODE_POWER8 | PPC_OPCODE_POWER9 | PPC_OPCODE_HTM
-		| PPC_OPCODE_ALTIVEC | PPC_OPCODE_ALTIVEC2
-		| PPC_OPCODE_VSX | PPC_OPCODE_VSX3);
+  if (cpu_has_feature(CPU_FTR_ALTIVEC))
+    dialect |= PPC_OPCODE_ALTIVEC | PPC_OPCODE_ALTIVEC2;
+
+  if (cpu_has_feature(CPU_FTR_VSX))
+    dialect |= PPC_OPCODE_VSX | PPC_OPCODE_VSX3;
 
   /* Get the major opcode of the insn.  */
   opcode = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/powerpc/xmon/xmon.c
+++ linux-xilinx-zynqmp-5.15.0/arch/powerpc/xmon/xmon.c
@@ -59,6 +59,7 @@
 #ifdef CONFIG_PPC64
 #include <asm/hvcall.h>
 #include <asm/paca.h>
+#include <asm/lppaca.h>
 #endif
 
 #include "nonstdio.h"
@@ -1355,7 +1356,7 @@
 	}
 	termch = cpu;
 
-	if (!scanhex(&cpu)) {
+	if (!scanhex(&cpu) || cpu >= num_possible_cpus()) {
 		/* print cpus waiting or in xmon */
 		printf("cpus stopped:");
 		last_cpu = first_cpu = NR_CPUS;
@@ -1528,9 +1529,9 @@
 	cmd = inchar();
 
 	switch (cmd) {
-	static const char badaddr[] = "Only kernel addresses are permitted for breakpoints\n";
-	int mode;
-	case 'd':	/* bd - hardware data breakpoint */
+	case 'd': {	/* bd - hardware data breakpoint */
+		static const char badaddr[] = "Only kernel addresses are permitted for breakpoints\n";
+		int mode;
 		if (xmon_is_ro) {
 			printf(xmon_ro_msg);
 			break;
@@ -1563,6 +1564,7 @@
 
 		force_enable_xmon();
 		break;
+	}
 
 	case 'i':	/* bi - hardware instr breakpoint */
 		if (xmon_is_ro) {
@@ -2769,7 +2771,7 @@
 
 	termch = c;	/* Put c back, it wasn't 'a' */
 
-	if (scanhex(&num))
+	if (scanhex(&num) && num < num_possible_cpus())
 		dump_one_paca(num);
 	else
 		dump_one_paca(xmon_owner);
@@ -2842,7 +2844,7 @@
 
 	termch = c;	/* Put c back, it wasn't 'a' */
 
-	if (scanhex(&num))
+	if (scanhex(&num) && num < num_possible_cpus())
 		dump_one_xive(num);
 	else
 		dump_one_xive(xmon_owner);
@@ -3264,8 +3266,7 @@
 	 * appropriate for calling from xmon. This could be moved
 	 * to a common, generic, routine used by both.
 	 */
-	state = (p_state == 0) ? 'R' :
-		(p_state < 0) ? 'U' :
+	state = (p_state == TASK_RUNNING) ? 'R' :
 		(p_state & TASK_UNINTERRUPTIBLE) ? 'D' :
 		(p_state & TASK_STOPPED) ? 'T' :
 		(p_state & TASK_TRACED) ? 'C' :
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/Kconfig
@@ -23,6 +23,7 @@
 	select ARCH_HAS_GIGANTIC_PAGE
 	select ARCH_HAS_KCOV
 	select ARCH_HAS_MMIOWB
+	select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
 	select ARCH_HAS_PTE_SPECIAL
 	select ARCH_HAS_SET_DIRECT_MAP if MMU
 	select ARCH_HAS_SET_MEMORY if MMU
@@ -46,7 +47,7 @@
 	select CLINT_TIMER if !MMU
 	select COMMON_CLK
 	select EDAC_SUPPORT
-	select GENERIC_ARCH_TOPOLOGY if SMP
+	select GENERIC_ARCH_TOPOLOGY
 	select GENERIC_ATOMIC64 if !64BIT
 	select GENERIC_CLOCKEVENTS_BROADCAST if SMP
 	select GENERIC_EARLY_IOREMAP
@@ -158,10 +159,9 @@
 
 config PAGE_OFFSET
 	hex
-	default 0xC0000000 if 32BIT && MAXPHYSMEM_1GB
+	default 0xC0000000 if 32BIT
 	default 0x80000000 if 64BIT && !MMU
-	default 0xffffffff80000000 if 64BIT && MAXPHYSMEM_2GB
-	default 0xffffffe000000000 if 64BIT && MAXPHYSMEM_128GB
+	default 0xffffffe000000000 if 64BIT
 
 config KASAN_SHADOW_OFFSET
 	hex
@@ -210,6 +210,11 @@
 config FIX_EARLYCON_MEM
 	def_bool MMU
 
+config ILLEGAL_POINTER_VALUE
+	hex
+	default 0 if 32BIT
+	default 0xdead000000000000 if 64BIT
+
 config PGTABLE_LEVELS
 	int
 	default 3 if 64BIT
@@ -270,24 +275,6 @@
 	bool
 	select HAVE_MOD_ARCH_SPECIFIC
 
-choice
-	prompt "Maximum Physical Memory"
-	default MAXPHYSMEM_1GB if 32BIT
-	default MAXPHYSMEM_2GB if 64BIT && CMODEL_MEDLOW
-	default MAXPHYSMEM_128GB if 64BIT && CMODEL_MEDANY
-
-	config MAXPHYSMEM_1GB
-		depends on 32BIT
-		bool "1GiB"
-	config MAXPHYSMEM_2GB
-		depends on 64BIT && CMODEL_MEDLOW
-		bool "2GiB"
-	config MAXPHYSMEM_128GB
-		depends on 64BIT && CMODEL_MEDANY
-		bool "128GiB"
-endchoice
-
-
 config SMP
 	bool "Symmetric Multi-Processing"
 	help
@@ -380,6 +367,28 @@
 
 endmenu
 
+config TOOLCHAIN_NEEDS_EXPLICIT_ZICSR_ZIFENCEI
+	def_bool y
+	# https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=aed44286efa8ae8717a77d94b51ac3614e2ca6dc
+	depends on AS_IS_GNU && AS_VERSION >= 23800
+	help
+	  Newer binutils versions default to ISA spec version 20191213 which
+	  moves some instructions from the I extension to the Zicsr and Zifencei
+	  extensions.
+
+config TOOLCHAIN_NEEDS_OLD_ISA_SPEC
+	def_bool y
+	depends on TOOLCHAIN_NEEDS_EXPLICIT_ZICSR_ZIFENCEI
+	# https://github.com/llvm/llvm-project/commit/22e199e6afb1263c943c0c0d4498694e15bf8a16
+	depends on CC_IS_CLANG && CLANG_VERSION < 170000
+	help
+	  Certain versions of clang do not support zicsr and zifencei via -march
+	  but newer versions of binutils require it for the reasons noted in the
+	  help text of CONFIG_TOOLCHAIN_NEEDS_EXPLICIT_ZICSR_ZIFENCEI. This
+	  option causes an older ISA spec compatible with these older versions
+	  of clang to be passed to GAS, which has the same result as passing zicsr
+	  and zifencei to -march.
+
 config FPU
 	bool "FPU support"
 	default y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/Kconfig.erratas
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/Kconfig.erratas
@@ -2,6 +2,7 @@
 
 config RISCV_ERRATA_ALTERNATIVE
 	bool "RISC-V alternative scheme"
+	depends on !XIP_KERNEL
 	default y
 	help
 	  This Kconfig allows the kernel to automatically patch the
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/Kconfig.socs
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/Kconfig.socs
@@ -14,8 +14,8 @@
 	select CLK_SIFIVE
 	select CLK_SIFIVE_PRCI
 	select SIFIVE_PLIC
-	select RISCV_ERRATA_ALTERNATIVE
-	select ERRATA_SIFIVE
+	select RISCV_ERRATA_ALTERNATIVE if !XIP_KERNEL
+	select ERRATA_SIFIVE if !XIP_KERNEL
 	help
 	  This enables support for SiFive SoC platform hardware.
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/Makefile
@@ -13,7 +13,11 @@
 ifeq ($(CONFIG_DYNAMIC_FTRACE),y)
 	LDFLAGS_vmlinux := --no-relax
 	KBUILD_CPPFLAGS += -DCC_USING_PATCHABLE_FUNCTION_ENTRY
-	CC_FLAGS_FTRACE := -fpatchable-function-entry=8
+ifeq ($(CONFIG_RISCV_ISA_C),y)
+	CC_FLAGS_FTRACE := -fpatchable-function-entry=4
+else
+	CC_FLAGS_FTRACE := -fpatchable-function-entry=2
+endif
 endif
 
 ifeq ($(CONFIG_CMODEL_MEDLOW),y)
@@ -39,6 +43,7 @@
 endif
 
 ifeq ($(CONFIG_LD_IS_LLD),y)
+ifeq ($(shell test $(CONFIG_LLD_VERSION) -lt 150000; echo $$?),0)
 	KBUILD_CFLAGS += -mno-relax
 	KBUILD_AFLAGS += -mno-relax
 ifndef CONFIG_AS_IS_LLVM
@@ -46,12 +51,21 @@
 	KBUILD_AFLAGS += -Wa,-mno-relax
 endif
 endif
+endif
 
 # ISA string setting
 riscv-march-$(CONFIG_ARCH_RV32I)	:= rv32ima
 riscv-march-$(CONFIG_ARCH_RV64I)	:= rv64ima
 riscv-march-$(CONFIG_FPU)		:= $(riscv-march-y)fd
 riscv-march-$(CONFIG_RISCV_ISA_C)	:= $(riscv-march-y)c
+
+ifdef CONFIG_TOOLCHAIN_NEEDS_OLD_ISA_SPEC
+KBUILD_CFLAGS += -Wa,-misa-spec=2.2
+KBUILD_AFLAGS += -Wa,-misa-spec=2.2
+else
+riscv-march-$(CONFIG_TOOLCHAIN_NEEDS_EXPLICIT_ZICSR_ZIFENCEI) := $(riscv-march-y)_zicsr_zifencei
+endif
+
 KBUILD_CFLAGS += -march=$(subst fd,,$(riscv-march-y))
 KBUILD_AFLAGS += -march=$(riscv-march-y)
 
@@ -68,7 +82,11 @@
         KBUILD_CFLAGS += -fno-omit-frame-pointer
 endif
 
+# Avoid generating .eh_frame sections.
+KBUILD_CFLAGS += -fno-asynchronous-unwind-tables -fno-unwind-tables
+
 KBUILD_CFLAGS_MODULE += $(call cc-option,-mno-relax)
+KBUILD_AFLAGS_MODULE += $(call as-option,-Wa$(comma)-mno-relax)
 
 # GCC versions that support the "-mstrict-align" option default to allowing
 # unaligned accesses.  While unaligned accesses are explicitly allowed in the
@@ -108,11 +126,13 @@
 vdso_install:
 	$(Q)$(MAKE) $(build)=arch/riscv/kernel/vdso $@
 
+ifeq ($(KBUILD_EXTMOD),)
 ifeq ($(CONFIG_MMU),y)
 prepare: vdso_prepare
 vdso_prepare: prepare0
 	$(Q)$(MAKE) $(build)=arch/riscv/kernel/vdso include/generated/vdso-offsets.h
 endif
+endif
 
 ifneq ($(CONFIG_XIP_KERNEL),y)
 ifeq ($(CONFIG_RISCV_M_MODE)$(CONFIG_SOC_CANAAN),yy)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/canaan/k210.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/canaan/k210.dtsi
@@ -65,6 +65,18 @@
 				compatible = "riscv,cpu-intc";
 			};
 		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
 	};
 
 	sram: memory@80000000 {
@@ -113,7 +125,8 @@
 			compatible = "canaan,k210-plic", "sifive,plic-1.0.0";
 			reg = <0xC000000 0x4000000>;
 			interrupt-controller;
-			interrupts-extended = <&cpu0_intc 11 &cpu1_intc 11>;
+			interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>,
+					      <&cpu1_intc 11>, <&cpu1_intc 9>;
 			riscv,ndev = <65>;
 		};
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
@@ -203,6 +203,8 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 		broken-flash-reset;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
@@ -205,6 +205,8 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 		broken-flash-reset;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
@@ -213,6 +213,8 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 		broken-flash-reset;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
@@ -178,6 +178,8 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 		broken-flash-reset;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
@@ -12,7 +12,7 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 	model = "Microchip PolarFire-SoC Icicle Kit";
-	compatible = "microchip,mpfs-icicle-kit";
+	compatible = "microchip,mpfs-icicle-kit", "microchip,mpfs";
 
 	aliases {
 		ethernet0 = &emac1;
@@ -56,8 +56,17 @@
 	status = "okay";
 };
 
-&sdcard {
+&mmc {
 	status = "okay";
+
+	bus-width = <4>;
+	disable-wp;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
 };
 
 &emac0 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
@@ -6,11 +6,8 @@
 / {
 	#address-cells = <2>;
 	#size-cells = <2>;
-	model = "Microchip MPFS Icicle Kit";
-	compatible = "microchip,mpfs-icicle-kit";
-
-	chosen {
-	};
+	model = "Microchip PolarFire SoC";
+	compatible = "microchip,mpfs";
 
 	cpus {
 		#address-cells = <1>;
@@ -262,39 +259,14 @@
 			status = "disabled";
 		};
 
-		emmc: mmc@20008000 {
+		/* Common node entry for emmc/sd */
+		mmc: mmc@20008000 {
 			compatible = "cdns,sd4hc";
 			reg = <0x0 0x20008000 0x0 0x1000>;
 			interrupt-parent = <&plic>;
 			interrupts = <88 89>;
 			pinctrl-names = "default";
 			clocks = <&clkcfg 6>;
-			bus-width = <4>;
-			cap-mmc-highspeed;
-			mmc-ddr-3_3v;
-			max-frequency = <200000000>;
-			non-removable;
-			no-sd;
-			no-sdio;
-			voltage-ranges = <3300 3300>;
-			status = "disabled";
-		};
-
-		sdcard: sdhc@20008000 {
-			compatible = "cdns,sd4hc";
-			reg = <0x0 0x20008000 0x0 0x1000>;
-			interrupt-parent = <&plic>;
-			interrupts = <88>;
-			pinctrl-names = "default";
-			clocks = <&clkcfg 6>;
-			bus-width = <4>;
-			disable-wp;
-			cap-sd-highspeed;
-			card-detect-delay = <200>;
-			sd-uhs-sdr12;
-			sd-uhs-sdr25;
-			sd-uhs-sdr50;
-			sd-uhs-sdr104;
 			max-frequency = <200000000>;
 			status = "disabled";
 		};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
@@ -166,7 +166,7 @@
 			clocks = <&prci PRCI_CLK_TLCLK>;
 			status = "disabled";
 		};
-		dma: dma@3000000 {
+		dma: dma-controller@3000000 {
 			compatible = "sifive,fu540-c000-pdma";
 			reg = <0x0 0x3000000 0x0 0x8000>;
 			interrupt-parent = <&plic0>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/sifive/fu740-c000.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/sifive/fu740-c000.dtsi
@@ -39,7 +39,7 @@
 			};
 		};
 		cpu1: cpu@1 {
-			compatible = "sifive,bullet0", "riscv";
+			compatible = "sifive,u74-mc", "sifive,bullet0", "riscv";
 			d-cache-block-size = <64>;
 			d-cache-sets = <64>;
 			d-cache-size = <32768>;
@@ -63,7 +63,7 @@
 			};
 		};
 		cpu2: cpu@2 {
-			compatible = "sifive,bullet0", "riscv";
+			compatible = "sifive,u74-mc", "sifive,bullet0", "riscv";
 			d-cache-block-size = <64>;
 			d-cache-sets = <64>;
 			d-cache-size = <32768>;
@@ -87,7 +87,7 @@
 			};
 		};
 		cpu3: cpu@3 {
-			compatible = "sifive,bullet0", "riscv";
+			compatible = "sifive,u74-mc", "sifive,bullet0", "riscv";
 			d-cache-block-size = <64>;
 			d-cache-sets = <64>;
 			d-cache-size = <32768>;
@@ -111,7 +111,7 @@
 			};
 		};
 		cpu4: cpu@4 {
-			compatible = "sifive,bullet0", "riscv";
+			compatible = "sifive,u74-mc", "sifive,bullet0", "riscv";
 			d-cache-block-size = <64>;
 			d-cache-sets = <64>;
 			d-cache-size = <32768>;
@@ -134,6 +134,30 @@
 				interrupt-controller;
 			};
 		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+
+				core4 {
+					cpu = <&cpu4>;
+				};
+			};
+		};
 	};
 	soc {
 		#address-cells = <2>;
@@ -304,7 +328,7 @@
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000  0x0 0x60080000  0x0 0x60080000 0x0 0x10000>,      /* I/O */
 				 <0x82000000  0x0 0x60090000  0x0 0x60090000 0x0 0xff70000>,    /* mem */
-				 <0x82000000  0x0 0x70000000  0x0 0x70000000 0x0 0x1000000>,    /* mem */
+				 <0x82000000  0x0 0x70000000  0x0 0x70000000 0x0 0x10000000>,    /* mem */
 				 <0xc3000000 0x20 0x00000000 0x20 0x00000000 0x20 0x00000000>;  /* mem prefetchable */
 			num-lanes = <0x8>;
 			interrupts = <56>, <57>, <58>, <59>, <60>, <61>, <62>, <63>, <64>;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/sifive/hifive-unleashed-a00-microsemi.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/sifive/hifive-unleashed-a00-microsemi.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "hifive-unleashed-a00.dts"
+
+/ {
+	soc {
+		pcie: pcie@2030000000 {
+			#address-cells = <0x3>;
+			#interrupt-cells = <0x1>;
+			#size-cells = <0x2>;
+			compatible = "microsemi,ms-pf-axi-pcie-host";
+			device_type = "pci";
+			bus-range = <0x01 0x7f>;
+			interrupt-map = <0 0 0 1 &ms_pcie_intc 0 0 0 0 2 &ms_pcie_intc 1 0 0 0 3 &ms_pcie_intc 2 0 0 0 4 &ms_pcie_intc 3>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-parent = <&plic0>;
+			interrupts = <32>;
+			ranges = <0x3000000 0x0 0x40000000 0x0 0x40000000 0x0 0x20000000>;
+			reg = <0x20 0x30000000 0x0 0x4000000 0x20 0x0 0x0 0x100000>;
+			reg-names = "control", "apb";
+			ms_pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+	};
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
@@ -3,6 +3,8 @@
 
 #include "fu540-c000.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
 
 /* Clock frequency (in Hz) of the PCB crystal for rtcclk */
 #define RTCCLK_FREQ		1000000
@@ -27,6 +29,37 @@
 	};
 
 	soc {
+		pwmleds {
+			compatible = "pwm-leds";
+			d1 {
+				label = "green:d1";
+				pwms = <&pwm0 0 7812500 PWM_POLARITY_INVERTED>;
+				active-low = <1>;
+				max-brightness = <255>;
+				linux,default-trigger = "none";
+			};
+			d2 {
+				label = "green:d2";
+				pwms = <&pwm0 1 7812500 PWM_POLARITY_INVERTED>;
+				active-low = <1>;
+				max-brightness = <255>;
+				linux,default-trigger = "none";
+			};
+			d3 {
+				label = "green:d3";
+				pwms = <&pwm0 2 7812500 PWM_POLARITY_INVERTED>;
+				active-low = <1>;
+				max-brightness = <255>;
+				linux,default-trigger = "none";
+			};
+			d4 {
+				label = "green:d4";
+				pwms = <&pwm0 3 7812500 PWM_POLARITY_INVERTED>;
+				active-low = <1>;
+				max-brightness = <255>;
+				linux,default-trigger = "none";
+			};
+		};
 	};
 
 	hfclk: hfclk {
@@ -46,6 +79,42 @@
 		compatible = "gpio-restart";
 		gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
 	};
+
+	led-controller {
+		compatible = "pwm-leds";
+
+		led-d1 {
+			pwms = <&pwm0 0 7812500 PWM_POLARITY_INVERTED>;
+			active-low;
+			color = <LED_COLOR_ID_GREEN>;
+			max-brightness = <255>;
+			label = "d1";
+		};
+
+		led-d2 {
+			pwms = <&pwm0 1 7812500 PWM_POLARITY_INVERTED>;
+			active-low;
+			color = <LED_COLOR_ID_GREEN>;
+			max-brightness = <255>;
+			label = "d2";
+		};
+
+		led-d3 {
+			pwms = <&pwm0 2 7812500 PWM_POLARITY_INVERTED>;
+			active-low;
+			color = <LED_COLOR_ID_GREEN>;
+			max-brightness = <255>;
+			label = "d3";
+		};
+
+		led-d4 {
+			pwms = <&pwm0 3 7812500 PWM_POLARITY_INVERTED>;
+			active-low;
+			color = <LED_COLOR_ID_GREEN>;
+			max-brightness = <255>;
+			label = "d4";
+		};
+	};
 };
 
 &uart0 {
@@ -80,6 +149,7 @@
 		spi-max-frequency = <20000000>;
 		voltage-ranges = <3300 3300>;
 		disable-wp;
+		gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts
@@ -2,6 +2,7 @@
 /* Copyright (c) 2020 SiFive, Inc */
 
 #include "fu740-c000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
 /* Clock frequency (in Hz) of the PCB crystal for rtcclk */
@@ -69,19 +70,20 @@
 		interrupt-parent = <&gpio>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 
 		regulators {
 			vdd_bcore1: bcore1 {
-				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
 				regulator-min-microamp = <5000000>;
 				regulator-max-microamp = <5000000>;
 				regulator-always-on;
 			};
 
 			vdd_bcore2: bcore2 {
-				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
 				regulator-min-microamp = <5000000>;
 				regulator-max-microamp = <5000000>;
 				regulator-always-on;
@@ -136,48 +138,48 @@
 			};
 
 			vdd_ldo3: ldo3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-min-microamp = <200000>;
 				regulator-max-microamp = <200000>;
 				regulator-always-on;
 			};
 
 			vdd_ldo4: ldo4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
 				regulator-min-microamp = <200000>;
 				regulator-max-microamp = <200000>;
 				regulator-always-on;
 			};
 
 			vdd_ldo5: ldo5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-min-microamp = <100000>;
 				regulator-max-microamp = <100000>;
 				regulator-always-on;
 			};
 
 			vdd_ldo6: ldo6 {
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-min-microamp = <200000>;
 				regulator-max-microamp = <200000>;
 				regulator-always-on;
 			};
 
 			vdd_ldo7: ldo7 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-min-microamp = <200000>;
 				regulator-max-microamp = <200000>;
 				regulator-always-on;
 			};
 
 			vdd_ldo8: ldo8 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-min-microamp = <200000>;
 				regulator-max-microamp = <200000>;
 				regulator-always-on;
@@ -228,6 +230,7 @@
 		spi-max-frequency = <20000000>;
 		voltage-ranges = <3300 3300>;
 		disable-wp;
+		gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/configs/defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/configs/defconfig
@@ -72,9 +72,11 @@
 CONFIG_GPIO_SIFIVE=y
 # CONFIG_PTP_1588_CLOCK is not set
 CONFIG_POWER_RESET=y
-CONFIG_DRM=y
-CONFIG_DRM_RADEON=y
-CONFIG_DRM_VIRTIO_GPU=y
+CONFIG_DRM=m
+CONFIG_DRM_RADEON=m
+CONFIG_DRM_NOUVEAU=m
+CONFIG_DRM_VIRTIO_GPU=m
+CONFIG_FB=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/configs/nommu_k210_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/configs/nommu_k210_defconfig
@@ -29,8 +29,6 @@
 CONFIG_SLOB=y
 # CONFIG_MMU is not set
 CONFIG_SOC_CANAAN=y
-CONFIG_SOC_CANAAN_K210_DTB_SOURCE="k210_generic"
-CONFIG_MAXPHYSMEM_2GB=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_CMDLINE="earlycon console=ttySIF0"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/configs/nommu_k210_sdcard_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/configs/nommu_k210_sdcard_defconfig
@@ -21,11 +21,9 @@
 CONFIG_SLOB=y
 # CONFIG_MMU is not set
 CONFIG_SOC_CANAAN=y
-CONFIG_SOC_CANAAN_K210_DTB_SOURCE="k210_generic"
-CONFIG_MAXPHYSMEM_2GB=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
-CONFIG_CMDLINE="earlycon console=ttySIF0 rootdelay=2 root=/dev/mmcblk0p1 ro"
+CONFIG_CMDLINE="earlycon console=ttySIF0 root=/dev/mmcblk0p1 rootwait ro"
 CONFIG_CMDLINE_FORCE=y
 # CONFIG_SECCOMP is not set
 # CONFIG_STACKPROTECTOR is not set
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/configs/nommu_virt_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/configs/nommu_virt_defconfig
@@ -27,7 +27,6 @@
 # CONFIG_SLAB_MERGE_DEFAULT is not set
 # CONFIG_MMU is not set
 CONFIG_SOC_VIRT=y
-CONFIG_MAXPHYSMEM_2GB=y
 CONFIG_SMP=y
 CONFIG_CMDLINE="root=/dev/vda rw earlycon=uart8250,mmio,0x10000000,115200n8 console=ttyS0"
 CONFIG_CMDLINE_FORCE=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/configs/rv32_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/configs/rv32_defconfig
@@ -71,6 +71,7 @@
 CONFIG_DRM=y
 CONFIG_DRM_RADEON=y
 CONFIG_DRM_VIRTIO_GPU=y
+CONFIG_FB=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/alternative-macros.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/alternative-macros.h
@@ -23,9 +23,9 @@
 888 :
 	\new_c
 889 :
-	.previous
 	.org    . - (889b - 888b) + (887b - 886b)
 	.org    . - (887b - 886b) + (889b - 888b)
+	.previous
 	.endif
 .endm
 
@@ -60,9 +60,9 @@
 	"888 :\n"							\
 	new_c "\n"							\
 	"889 :\n"							\
-	".previous\n"							\
 	".org	. - (887b - 886b) + (889b - 888b)\n"			\
 	".org	. - (889b - 888b) + (887b - 886b)\n"			\
+	".previous\n"							\
 	".endif\n"
 
 #define __ALTERNATIVE_CFG(old_c, new_c, vendor_id, errata_id, enable) \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/asm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/asm.h
@@ -23,6 +23,7 @@
 #define REG_L		__REG_SEL(ld, lw)
 #define REG_S		__REG_SEL(sd, sw)
 #define REG_SC		__REG_SEL(sc.d, sc.w)
+#define REG_AMOSWAP_AQ	__REG_SEL(amoswap.d.aq, amoswap.w.aq)
 #define REG_ASM		__REG_SEL(.dword, .word)
 #define SZREG		__REG_SEL(8, 4)
 #define LGREG		__REG_SEL(3, 2)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/bug.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/bug.h
@@ -30,8 +30,8 @@
 typedef u32 bug_insn_t;
 
 #ifdef CONFIG_GENERIC_BUG_RELATIVE_POINTERS
-#define __BUG_ENTRY_ADDR	RISCV_INT " 1b - 2b"
-#define __BUG_ENTRY_FILE	RISCV_INT " %0 - 2b"
+#define __BUG_ENTRY_ADDR	RISCV_INT " 1b - ."
+#define __BUG_ENTRY_FILE	RISCV_INT " %0 - ."
 #else
 #define __BUG_ENTRY_ADDR	RISCV_PTR " 1b"
 #define __BUG_ENTRY_FILE	RISCV_PTR " %0"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/efi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/efi.h
@@ -10,10 +10,10 @@
 #include <asm/mmu_context.h>
 #include <asm/ptrace.h>
 #include <asm/tlbflush.h>
+#include <asm/pgalloc.h>
 
 #ifdef CONFIG_EFI
 extern void efi_init(void);
-extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
 #else
 #define efi_init()
 #endif
@@ -21,7 +21,10 @@
 int efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md);
 int efi_set_mapping_permissions(struct mm_struct *mm, efi_memory_desc_t *md);
 
-#define arch_efi_call_virt_setup()      efi_virtmap_load()
+#define arch_efi_call_virt_setup()      ({		\
+		sync_kernel_mappings(efi_mm.pgd);	\
+		efi_virtmap_load();			\
+	})
 #define arch_efi_call_virt_teardown()   efi_virtmap_unload()
 
 #define arch_efi_call_virt(p, f, args...) p->f(args)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/fixmap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/fixmap.h
@@ -22,6 +22,14 @@
  */
 enum fixed_addresses {
 	FIX_HOLE,
+	/*
+	 * The fdt fixmap mapping must be PMD aligned and will be mapped
+	 * using PMD entries in fixmap_pmd in 64-bit and a PGD entry in 32-bit.
+	 */
+	FIX_FDT_END,
+	FIX_FDT = FIX_FDT_END + FIX_FDT_SIZE / PAGE_SIZE - 1,
+
+	/* Below fixmaps will be mapped using fixmap_pte */
 	FIX_PTE,
 	FIX_PMD,
 	FIX_TEXT_POKE1,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/ftrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/ftrace.h
@@ -42,6 +42,14 @@
  * 2) jalr: setting low-12 offset to ra, jump to ra, and set ra to
  *          return address (original pc + 4)
  *
+ *<ftrace enable>:
+ * 0: auipc  t0/ra, 0x?
+ * 4: jalr   t0/ra, ?(t0/ra)
+ *
+ *<ftrace disable>:
+ * 0: nop
+ * 4: nop
+ *
  * Dynamic ftrace generates probes to call sites, so we must deal with
  * both auipc and jalr at the same time.
  */
@@ -52,25 +60,43 @@
 #define AUIPC_OFFSET_MASK	(0xfffff000)
 #define AUIPC_PAD		(0x00001000)
 #define JALR_SHIFT		20
-#define JALR_BASIC		(0x000080e7)
-#define AUIPC_BASIC		(0x00000097)
+#define JALR_RA			(0x000080e7)
+#define AUIPC_RA		(0x00000097)
+#define JALR_T0			(0x000282e7)
+#define AUIPC_T0		(0x00000297)
 #define NOP4			(0x00000013)
 
-#define make_call(caller, callee, call)					\
+#define to_jalr_t0(offset)						\
+	(((offset & JALR_OFFSET_MASK) << JALR_SHIFT) | JALR_T0)
+
+#define to_auipc_t0(offset)						\
+	((offset & JALR_SIGN_MASK) ?					\
+	(((offset & AUIPC_OFFSET_MASK) + AUIPC_PAD) | AUIPC_T0) :	\
+	((offset & AUIPC_OFFSET_MASK) | AUIPC_T0))
+
+#define make_call_t0(caller, callee, call)				\
 do {									\
-	call[0] = to_auipc_insn((unsigned int)((unsigned long)callee -	\
-				(unsigned long)caller));		\
-	call[1] = to_jalr_insn((unsigned int)((unsigned long)callee -	\
-			       (unsigned long)caller));			\
+	unsigned int offset =						\
+		(unsigned long) (callee) - (unsigned long) (caller);	\
+	call[0] = to_auipc_t0(offset);					\
+	call[1] = to_jalr_t0(offset);					\
 } while (0)
 
-#define to_jalr_insn(offset)						\
-	(((offset & JALR_OFFSET_MASK) << JALR_SHIFT) | JALR_BASIC)
+#define to_jalr_ra(offset)						\
+	(((offset & JALR_OFFSET_MASK) << JALR_SHIFT) | JALR_RA)
 
-#define to_auipc_insn(offset)						\
+#define to_auipc_ra(offset)						\
 	((offset & JALR_SIGN_MASK) ?					\
-	(((offset & AUIPC_OFFSET_MASK) + AUIPC_PAD) | AUIPC_BASIC) :	\
-	((offset & AUIPC_OFFSET_MASK) | AUIPC_BASIC))
+	(((offset & AUIPC_OFFSET_MASK) + AUIPC_PAD) | AUIPC_RA) :	\
+	((offset & AUIPC_OFFSET_MASK) | AUIPC_RA))
+
+#define make_call_ra(caller, callee, call)				\
+do {									\
+	unsigned int offset =						\
+		(unsigned long) (callee) - (unsigned long) (caller);	\
+	call[0] = to_auipc_ra(offset);					\
+	call[1] = to_jalr_ra(offset);					\
+} while (0)
 
 /*
  * Let auipc+jalr be the basic *mcount unit*, so we make it 8 bytes here.
@@ -83,6 +109,6 @@
 #define ftrace_init_nop ftrace_init_nop
 #endif
 
-#endif
+#endif /* CONFIG_DYNAMIC_FTRACE */
 
 #endif /* _ASM_RISCV_FTRACE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/hugetlb.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/hugetlb.h
@@ -5,4 +5,10 @@
 #include <asm-generic/hugetlb.h>
 #include <asm/page.h>
 
+static inline void arch_clear_hugepage_flags(struct page *page)
+{
+	clear_bit(PG_dcache_clean, &page->flags);
+}
+#define arch_clear_hugepage_flags arch_clear_hugepage_flags
+
 #endif /* _ASM_RISCV_HUGETLB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/io.h
@@ -101,9 +101,9 @@
 __io_reads_ins(ins,  u8, b, __io_pbr(), __io_par(addr))
 __io_reads_ins(ins, u16, w, __io_pbr(), __io_par(addr))
 __io_reads_ins(ins, u32, l, __io_pbr(), __io_par(addr))
-#define insb(addr, buffer, count) __insb((void __iomem *)(long)addr, buffer, count)
-#define insw(addr, buffer, count) __insw((void __iomem *)(long)addr, buffer, count)
-#define insl(addr, buffer, count) __insl((void __iomem *)(long)addr, buffer, count)
+#define insb(addr, buffer, count) __insb(PCI_IOBASE + (addr), buffer, count)
+#define insw(addr, buffer, count) __insw(PCI_IOBASE + (addr), buffer, count)
+#define insl(addr, buffer, count) __insl(PCI_IOBASE + (addr), buffer, count)
 
 __io_writes_outs(writes,  u8, b, __io_bw(), __io_aw())
 __io_writes_outs(writes, u16, w, __io_bw(), __io_aw())
@@ -115,22 +115,22 @@
 __io_writes_outs(outs,  u8, b, __io_pbw(), __io_paw())
 __io_writes_outs(outs, u16, w, __io_pbw(), __io_paw())
 __io_writes_outs(outs, u32, l, __io_pbw(), __io_paw())
-#define outsb(addr, buffer, count) __outsb((void __iomem *)(long)addr, buffer, count)
-#define outsw(addr, buffer, count) __outsw((void __iomem *)(long)addr, buffer, count)
-#define outsl(addr, buffer, count) __outsl((void __iomem *)(long)addr, buffer, count)
+#define outsb(addr, buffer, count) __outsb(PCI_IOBASE + (addr), buffer, count)
+#define outsw(addr, buffer, count) __outsw(PCI_IOBASE + (addr), buffer, count)
+#define outsl(addr, buffer, count) __outsl(PCI_IOBASE + (addr), buffer, count)
 
 #ifdef CONFIG_64BIT
 __io_reads_ins(reads, u64, q, __io_br(), __io_ar(addr))
 #define readsq(addr, buffer, count) __readsq(addr, buffer, count)
 
 __io_reads_ins(ins, u64, q, __io_pbr(), __io_par(addr))
-#define insq(addr, buffer, count) __insq((void __iomem *)addr, buffer, count)
+#define insq(addr, buffer, count) __insq(PCI_IOBASE + (addr), buffer, count)
 
 __io_writes_outs(writes, u64, q, __io_bw(), __io_aw())
 #define writesq(addr, buffer, count) __writesq(addr, buffer, count)
 
 __io_writes_outs(outs, u64, q, __io_pbr(), __io_paw())
-#define outsq(addr, buffer, count) __outsq((void __iomem *)addr, buffer, count)
+#define outsq(addr, buffer, count) __outsq(PCI_IOBASE + (addr), buffer, count)
 #endif
 
 #include <asm-generic/io.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/irq_work.h
@@ -4,7 +4,7 @@
 
 static inline bool arch_irq_work_has_interrupt(void)
 {
-	return true;
+	return IS_ENABLED(CONFIG_SMP);
 }
-extern void arch_irq_work_raise(void);
+
 #endif /* _ASM_RISCV_IRQ_WORK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/jump_label.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/jump_label.h
@@ -18,6 +18,7 @@
 					       bool branch)
 {
 	asm_volatile_goto(
+		"	.align		2			\n\t"
 		"	.option push				\n\t"
 		"	.option norelax				\n\t"
 		"	.option norvc				\n\t"
@@ -39,6 +40,7 @@
 						    bool branch)
 {
 	asm_volatile_goto(
+		"	.align		2			\n\t"
 		"	.option push				\n\t"
 		"	.option norelax				\n\t"
 		"	.option norvc				\n\t"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/kprobes.h
@@ -40,7 +40,7 @@
 int kprobe_fault_handler(struct pt_regs *regs, unsigned int trapnr);
 bool kprobe_breakpoint_handler(struct pt_regs *regs);
 bool kprobe_single_step_handler(struct pt_regs *regs);
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 void __kprobes *trampoline_probe_handler(struct pt_regs *regs);
 
 #endif /* CONFIG_KPROBES */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/mmio.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/mmio.h
@@ -101,9 +101,9 @@
  * Relaxed I/O memory access primitives. These follow the Device memory
  * ordering rules but do not guarantee any ordering relative to Normal memory
  * accesses.  These are defined to order the indicated access (either a read or
- * write) with all other I/O memory accesses. Since the platform specification
- * defines that all I/O regions are strongly ordered on channel 2, no explicit
- * fences are required to enforce this ordering.
+ * write) with all other I/O memory accesses to the same peripheral. Since the
+ * platform specification defines that all I/O regions are strongly ordered on
+ * channel 0, no explicit fences are required to enforce this ordering.
  */
 /* FIXME: These are now the same as asm-generic */
 #define __io_rbr()		do {} while (0)
@@ -125,14 +125,14 @@
 #endif
 
 /*
- * I/O memory access primitives. Reads are ordered relative to any
- * following Normal memory access. Writes are ordered relative to any prior
- * Normal memory access.  The memory barriers here are necessary as RISC-V
+ * I/O memory access primitives.  Reads are ordered relative to any following
+ * Normal memory read and delay() loop.  Writes are ordered relative to any
+ * prior Normal memory write.  The memory barriers here are necessary as RISC-V
  * doesn't define any ordering between the memory space and the I/O space.
  */
 #define __io_br()	do {} while (0)
-#define __io_ar(v)	__asm__ __volatile__ ("fence i,r" : : : "memory")
-#define __io_bw()	__asm__ __volatile__ ("fence w,o" : : : "memory")
+#define __io_ar(v)	({ __asm__ __volatile__ ("fence i,ir" : : : "memory"); })
+#define __io_bw()	({ __asm__ __volatile__ ("fence w,o" : : : "memory"); })
 #define __io_aw()	mmiowb_set_pending()
 
 #define readb(c)	({ u8  __v; __io_br(); __v = readb_cpu(c); __io_ar(__v); __v; })
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/module.lds.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/module.lds.h
@@ -2,8 +2,8 @@
 /* Copyright (C) 2017 Andes Technology Corporation */
 #ifdef CONFIG_MODULE_SECTIONS
 SECTIONS {
-	.plt (NOLOAD) : { BYTE(0) }
-	.got (NOLOAD) : { BYTE(0) }
-	.got.plt (NOLOAD) : { BYTE(0) }
+	.plt : { BYTE(0) }
+	.got : { BYTE(0) }
+	.got.plt : { BYTE(0) }
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/parse_asm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/parse_asm.h
@@ -3,6 +3,9 @@
  * Copyright (C) 2020 SiFive
  */
 
+#ifndef _ASM_RISCV_INSN_H
+#define _ASM_RISCV_INSN_H
+
 #include <linux/bits.h>
 
 /* The bit field of immediate value in I-type instruction */
@@ -125,7 +128,7 @@
 #define FUNCT3_C_J		0xa000
 #define FUNCT3_C_JAL		0x2000
 #define FUNCT4_C_JR		0x8000
-#define FUNCT4_C_JALR		0xf000
+#define FUNCT4_C_JALR		0x9000
 
 #define FUNCT12_SRET		0x10200000
 
@@ -217,3 +220,5 @@
 	(RVC_X(x_, RVC_B_IMM_5_OPOFF, RVC_B_IMM_5_MASK) << RVC_B_IMM_5_OFF) | \
 	(RVC_X(x_, RVC_B_IMM_7_6_OPOFF, RVC_B_IMM_7_6_MASK) << RVC_B_IMM_7_6_OFF) | \
 	(RVC_IMM_SIGN(x_) << RVC_B_IMM_SIGN_OFF); })
+
+#endif /* _ASM_RISCV_INSN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/patch.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/patch.h
@@ -9,4 +9,6 @@
 int patch_text_nosync(void *addr, const void *insns, size_t len);
 int patch_text(void *addr, u32 insn);
 
+extern int riscv_patch_in_stop_machine;
+
 #endif /* _ASM_RISCV_PATCH_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/pgalloc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/pgalloc.h
@@ -38,6 +38,13 @@
 }
 #endif /* __PAGETABLE_PMD_FOLDED */
 
+static inline void sync_kernel_mappings(pgd_t *pgd)
+{
+	memcpy(pgd + USER_PTRS_PER_PGD,
+	       init_mm.pgd + USER_PTRS_PER_PGD,
+	       (PTRS_PER_PGD - USER_PTRS_PER_PGD) * sizeof(pgd_t));
+}
+
 static inline pgd_t *pgd_alloc(struct mm_struct *mm)
 {
 	pgd_t *pgd;
@@ -46,9 +53,7 @@
 	if (likely(pgd != NULL)) {
 		memset(pgd, 0, USER_PTRS_PER_PGD * sizeof(pgd_t));
 		/* Copy kernel mappings */
-		memcpy(pgd + USER_PTRS_PER_PGD,
-			init_mm.pgd + USER_PTRS_PER_PGD,
-			(PTRS_PER_PGD - USER_PTRS_PER_PGD) * sizeof(pgd_t));
+		sync_kernel_mappings(pgd);
 	}
 	return pgd;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/pgtable.h
@@ -58,7 +58,7 @@
  * Define vmemmap for pfn_to_page & page_to_pfn calls. Needed if kernel
  * is configured with CONFIG_SPARSEMEM_VMEMMAP enabled.
  */
-#define vmemmap		((struct page *)VMEMMAP_START)
+#define vmemmap		((struct page *)VMEMMAP_START - (phys_ram_base >> PAGE_SHIFT))
 
 #define PCI_IO_SIZE      SZ_16M
 #define PCI_IO_END       VMEMMAP_START
@@ -66,9 +66,13 @@
 
 #define FIXADDR_TOP      PCI_IO_START
 #ifdef CONFIG_64BIT
-#define FIXADDR_SIZE     PMD_SIZE
+#define MAX_FDT_SIZE	 PMD_SIZE
+#define FIX_FDT_SIZE	 (MAX_FDT_SIZE + SZ_2M)
+#define FIXADDR_SIZE     (PMD_SIZE + FIX_FDT_SIZE)
 #else
-#define FIXADDR_SIZE     PGDIR_SIZE
+#define MAX_FDT_SIZE	 PGDIR_SIZE
+#define FIX_FDT_SIZE	 MAX_FDT_SIZE
+#define FIXADDR_SIZE     (PGDIR_SIZE + FIX_FDT_SIZE)
 #endif
 #define FIXADDR_START    (FIXADDR_TOP - FIXADDR_SIZE)
 
@@ -671,8 +675,8 @@
 #define PAGE_SHARED		__pgprot(0)
 #define PAGE_KERNEL		__pgprot(0)
 #define swapper_pg_dir		NULL
-#define TASK_SIZE		0xffffffffUL
-#define VMALLOC_START		0
+#define TASK_SIZE		_AC(-1, UL)
+#define VMALLOC_START		_AC(0, UL)
 #define VMALLOC_END		TASK_SIZE
 
 #endif /* !CONFIG_MMU */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/sections.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/sections.h
@@ -13,6 +13,7 @@
 extern char __init_data_begin[], __init_data_end[];
 extern char __init_text_begin[], __init_text_end[];
 extern char __alt_start[], __alt_end[];
+extern char __exittext_begin[], __exittext_end[];
 
 static inline bool is_va_kernel_text(uintptr_t va)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/smp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/smp.h
@@ -43,7 +43,6 @@
 void arch_send_call_function_single_ipi(int cpu);
 
 int riscv_hartid_to_cpuid(int hartid);
-void riscv_cpuid_to_hartid_mask(const struct cpumask *in, struct cpumask *out);
 
 /* Set custom IPI operations */
 void riscv_set_ipi_ops(const struct riscv_ipi_ops *ops);
@@ -85,13 +84,6 @@
 	return boot_cpu_hartid;
 }
 
-static inline void riscv_cpuid_to_hartid_mask(const struct cpumask *in,
-					      struct cpumask *out)
-{
-	cpumask_clear(out);
-	cpumask_set_cpu(boot_cpu_hartid, out);
-}
-
 static inline void riscv_set_ipi_ops(const struct riscv_ipi_ops *ops)
 {
 }
@@ -102,6 +94,8 @@
 
 #endif /* CONFIG_SMP */
 
+void riscv_cpuid_to_hartid_mask(const struct cpumask *in, struct cpumask *out);
+
 #if defined(CONFIG_HOTPLUG_CPU) && (CONFIG_SMP)
 bool cpu_has_hotplug(unsigned int cpu);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/thread_info.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/thread_info.h
@@ -11,11 +11,17 @@
 #include <asm/page.h>
 #include <linux/const.h>
 
+#ifdef CONFIG_KASAN
+#define KASAN_STACK_ORDER 1
+#else
+#define KASAN_STACK_ORDER 0
+#endif
+
 /* thread information allocation */
 #ifdef CONFIG_64BIT
-#define THREAD_SIZE_ORDER	(2)
+#define THREAD_SIZE_ORDER	(2 + KASAN_STACK_ORDER)
 #else
-#define THREAD_SIZE_ORDER	(1)
+#define THREAD_SIZE_ORDER	(1 + KASAN_STACK_ORDER)
 #endif
 #define THREAD_SIZE		(PAGE_SIZE << THREAD_SIZE_ORDER)
 
@@ -36,6 +42,9 @@
 
 #ifndef __ASSEMBLY__
 
+extern long shadow_stack[SHADOW_OVERFLOW_STACK_SIZE / sizeof(long)];
+extern unsigned long spin_shadow_stack;
+
 #include <asm/processor.h>
 #include <asm/csr.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/timex.h
@@ -41,7 +41,7 @@
 static inline unsigned long random_get_entropy(void)
 {
 	if (unlikely(clint_time_val == NULL))
-		return 0;
+		return random_get_entropy_fallback();
 	return get_cycles();
 }
 #define random_get_entropy()	random_get_entropy()
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/tlbflush.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/tlbflush.h
@@ -12,6 +12,8 @@
 #include <asm/errata_list.h>
 
 #ifdef CONFIG_MMU
+extern unsigned long asid_mask;
+
 static inline void local_flush_tlb_all(void)
 {
 	__asm__ __volatile__ ("sfence.vma" : : : "memory");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/uaccess.h
@@ -216,7 +216,7 @@
 	might_fault();						\
 	access_ok(__p, sizeof(*__p)) ?		\
 		__get_user((x), __p) :				\
-		((x) = 0, -EFAULT);				\
+		((x) = (__force __typeof__(x))0, -EFAULT);	\
 })
 
 #define __put_user_asm(insn, x, ptr, err)			\
@@ -467,7 +467,7 @@
 
 #define __get_kernel_nofault(dst, src, type, err_label)			\
 do {									\
-	long __kr_err;							\
+	long __kr_err = 0;						\
 									\
 	__get_user_nocheck(*((type *)(dst)), (type *)(src), __kr_err);	\
 	if (unlikely(__kr_err))						\
@@ -476,7 +476,7 @@
 
 #define __put_kernel_nofault(dst, src, type, err_label)			\
 do {									\
-	long __kr_err;							\
+	long __kr_err = 0;						\
 									\
 	__put_user_nocheck(*((type *)(src)), (type *)(dst), __kr_err);	\
 	if (unlikely(__kr_err))						\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/asm/unistd.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/asm/unistd.h
@@ -9,7 +9,6 @@
  */
 
 #define __ARCH_WANT_SYS_CLONE
-#define __ARCH_WANT_MEMFD_SECRET
 
 #include <uapi/asm/unistd.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/uapi/asm/setup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/uapi/asm/setup.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only WITH Linux-syscall-note */
+
+#ifndef _UAPI_ASM_RISCV_SETUP_H
+#define _UAPI_ASM_RISCV_SETUP_H
+
+#define COMMAND_LINE_SIZE	1024
+
+#endif /* _UAPI_ASM_RISCV_SETUP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/include/uapi/asm/unistd.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/include/uapi/asm/unistd.h
@@ -21,6 +21,7 @@
 #endif /* __LP64__ */
 
 #define __ARCH_WANT_SYS_CLONE3
+#define __ARCH_WANT_MEMFD_SECRET
 
 #include <asm-generic/unistd.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/Makefile
@@ -50,6 +50,8 @@
 obj-$(CONFIG_FUNCTION_TRACER)	+= mcount.o ftrace.o
 obj-$(CONFIG_DYNAMIC_FTRACE)	+= mcount-dyn.o
 
+obj-$(CONFIG_TRACE_IRQFLAGS)	+= trace_irq.o
+
 obj-$(CONFIG_RISCV_BASE_PMU)	+= perf_event.o
 obj-$(CONFIG_PERF_EVENTS)	+= perf_callchain.o
 obj-$(CONFIG_HAVE_PERF_REGS)	+= perf_regs.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/asm-offsets.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/asm-offsets.c
@@ -4,8 +4,6 @@
  * Copyright (C) 2017 SiFive
  */
 
-#define GENERATING_ASM_OFFSETS
-
 #include <linux/kbuild.h>
 #include <linux/sched.h>
 #include <asm/thread_info.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/cpu-hotplug.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/cpu-hotplug.c
@@ -12,6 +12,7 @@
 #include <linux/sched/hotplug.h>
 #include <asm/irq.h>
 #include <asm/cpu_ops.h>
+#include <asm/numa.h>
 #include <asm/sbi.h>
 
 void cpu_stop(void);
@@ -46,6 +47,7 @@
 		return ret;
 
 	remove_cpu_topology(cpu);
+	numa_remove_cpu(cpu);
 	set_cpu_online(cpu, false);
 	irq_migrate_all_off_this_cpu();
 
@@ -69,7 +71,7 @@
 	if (cpu_ops[cpu]->cpu_is_stopped)
 		ret = cpu_ops[cpu]->cpu_is_stopped(cpu);
 	if (ret)
-		pr_warn("CPU%d may not have stopped: %d\n", cpu, ret);
+		pr_warn("CPU%u may not have stopped: %d\n", cpu, ret);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/cpu_ops.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/cpu_ops.c
@@ -28,8 +28,7 @@
 
 	/* Make sure tidle is updated */
 	smp_mb();
-	WRITE_ONCE(__cpu_up_stack_pointer[hartid],
-		   task_stack_page(tidle) + THREAD_SIZE);
+	WRITE_ONCE(__cpu_up_stack_pointer[hartid], task_pt_regs(tidle));
 	WRITE_ONCE(__cpu_up_task_pointer[hartid], tidle);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/crash_save_regs.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/crash_save_regs.S
@@ -44,7 +44,7 @@
 	REG_S t6,  PT_T6(a0)	/* x31 */
 
 	csrr t1, CSR_STATUS
-	csrr t2, CSR_EPC
+	auipc t2, 0x0
 	csrr t3, CSR_TVAL
 	csrr t4, CSR_CAUSE
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/efi-header.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/efi-header.S
@@ -59,7 +59,7 @@
 	.long	efi_header_end - _start			// SizeOfHeaders
 	.long	0					// CheckSum
 	.short	IMAGE_SUBSYSTEM_EFI_APPLICATION		// Subsystem
-	.short	0					// DllCharacteristics
+	.short	IMAGE_DLL_CHARACTERISTICS_NX_COMPAT	// DllCharacteristics
 	.quad	0					// SizeOfStackReserve
 	.quad	0					// SizeOfStackCommit
 	.quad	0					// SizeOfHeapReserve
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/efi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/efi.c
@@ -65,7 +65,7 @@
 
 	if (md->attribute & EFI_MEMORY_RO) {
 		val = pte_val(pte) & ~_PAGE_WRITE;
-		val = pte_val(pte) | _PAGE_READ;
+		val |= _PAGE_READ;
 		pte = __pte(val);
 	}
 	if (md->attribute & EFI_MEMORY_XP) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/entry.S
@@ -108,7 +108,7 @@
 .option pop
 
 #ifdef CONFIG_TRACE_IRQFLAGS
-	call trace_hardirqs_off
+	call __trace_hardirqs_off
 #endif
 
 #ifdef CONFIG_CONTEXT_TRACKING
@@ -144,7 +144,7 @@
 	li t0, EXC_BREAKPOINT
 	beq s4, t0, 1f
 #ifdef CONFIG_TRACE_IRQFLAGS
-	call trace_hardirqs_on
+	call __trace_hardirqs_on
 #endif
 	csrs CSR_STATUS, SR_IE
 
@@ -231,11 +231,11 @@
 	andi t0, t0, _TIF_SYSCALL_WORK
 	bnez t0, handle_syscall_trace_exit
 
-ret_from_exception:
+SYM_CODE_START_NOALIGN(ret_from_exception)
 	REG_L s0, PT_STATUS(sp)
 	csrc CSR_STATUS, SR_IE
 #ifdef CONFIG_TRACE_IRQFLAGS
-	call trace_hardirqs_off
+	call __trace_hardirqs_off
 #endif
 #ifdef CONFIG_RISCV_M_MODE
 	/* the MPP value is too large to be used as an immediate arg for addi */
@@ -245,6 +245,7 @@
 	andi s0, s0, SR_SPP
 #endif
 	bnez s0, resume_kernel
+SYM_CODE_END(ret_from_exception)
 
 resume_userspace:
 	/* Interrupts must be disabled here so flags are checked atomically */
@@ -271,10 +272,10 @@
 	REG_L s1, PT_STATUS(sp)
 	andi t0, s1, SR_PIE
 	beqz t0, 1f
-	call trace_hardirqs_on
+	call __trace_hardirqs_on
 	j 2f
 1:
-	call trace_hardirqs_off
+	call __trace_hardirqs_off
 2:
 #endif
 	REG_L a0, PT_STATUS(sp)
@@ -387,6 +388,19 @@
 
 #ifdef CONFIG_VMAP_STACK
 handle_kernel_stack_overflow:
+	/*
+	 * Takes the psuedo-spinlock for the shadow stack, in case multiple
+	 * harts are concurrently overflowing their kernel stacks.  We could
+	 * store any value here, but since we're overflowing the kernel stack
+	 * already we only have SP to use as a scratch register.  So we just
+	 * swap in the address of the spinlock, as that's definately non-zero.
+	 *
+	 * Pairs with a store_release in handle_bad_stack().
+	 */
+1:	la sp, spin_shadow_stack
+	REG_AMOSWAP_AQ sp, sp, (sp)
+	bnez sp, 1b
+
 	la sp, shadow_stack
 	addi sp, sp, SHADOW_OVERFLOW_STACK_SIZE
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/ftrace.c
@@ -15,11 +15,21 @@
 int ftrace_arch_code_modify_prepare(void) __acquires(&text_mutex)
 {
 	mutex_lock(&text_mutex);
+
+	/*
+	 * The code sequences we use for ftrace can't be patched while the
+	 * kernel is running, so we need to use stop_machine() to modify them
+	 * for now.  This doesn't play nice with text_mutex, we use this flag
+	 * to elide the check.
+	 */
+	riscv_patch_in_stop_machine = true;
+
 	return 0;
 }
 
 int ftrace_arch_code_modify_post_process(void) __releases(&text_mutex)
 {
+	riscv_patch_in_stop_machine = false;
 	mutex_unlock(&text_mutex);
 	return 0;
 }
@@ -57,12 +67,15 @@
 }
 
 static int __ftrace_modify_call(unsigned long hook_pos, unsigned long target,
-				bool enable)
+				bool enable, bool ra)
 {
 	unsigned int call[2];
 	unsigned int nops[2] = {NOP4, NOP4};
 
-	make_call(hook_pos, target, call);
+	if (ra)
+		make_call_ra(hook_pos, target, call);
+	else
+		make_call_t0(hook_pos, target, call);
 
 	/* Replace the auipc-jalr pair at once. Return -EPERM on write error. */
 	if (patch_text_nosync
@@ -72,42 +85,13 @@
 	return 0;
 }
 
-/*
- * Put 5 instructions with 16 bytes at the front of function within
- * patchable function entry nops' area.
- *
- * 0: REG_S  ra, -SZREG(sp)
- * 1: auipc  ra, 0x?
- * 2: jalr   -?(ra)
- * 3: REG_L  ra, -SZREG(sp)
- *
- * So the opcodes is:
- * 0: 0xfe113c23 (sd)/0xfe112e23 (sw)
- * 1: 0x???????? -> auipc
- * 2: 0x???????? -> jalr
- * 3: 0xff813083 (ld)/0xffc12083 (lw)
- */
-#if __riscv_xlen == 64
-#define INSN0	0xfe113c23
-#define INSN3	0xff813083
-#elif __riscv_xlen == 32
-#define INSN0	0xfe112e23
-#define INSN3	0xffc12083
-#endif
-
-#define FUNC_ENTRY_SIZE	16
-#define FUNC_ENTRY_JMP	4
-
 int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
 {
-	unsigned int call[4] = {INSN0, 0, 0, INSN3};
-	unsigned long target = addr;
-	unsigned long caller = rec->ip + FUNC_ENTRY_JMP;
+	unsigned int call[2];
 
-	call[1] = to_auipc_insn((unsigned int)(target - caller));
-	call[2] = to_jalr_insn((unsigned int)(target - caller));
+	make_call_t0(rec->ip, addr, call);
 
-	if (patch_text_nosync((void *)rec->ip, call, FUNC_ENTRY_SIZE))
+	if (patch_text_nosync((void *)rec->ip, call, MCOUNT_INSN_SIZE))
 		return -EPERM;
 
 	return 0;
@@ -116,15 +100,14 @@
 int ftrace_make_nop(struct module *mod, struct dyn_ftrace *rec,
 		    unsigned long addr)
 {
-	unsigned int nops[4] = {NOP4, NOP4, NOP4, NOP4};
+	unsigned int nops[2] = {NOP4, NOP4};
 
-	if (patch_text_nosync((void *)rec->ip, nops, FUNC_ENTRY_SIZE))
+	if (patch_text_nosync((void *)rec->ip, nops, MCOUNT_INSN_SIZE))
 		return -EPERM;
 
 	return 0;
 }
 
-
 /*
  * This is called early on, and isn't wrapped by
  * ftrace_arch_code_modify_{prepare,post_process}() and therefor doesn't hold
@@ -136,9 +119,9 @@
 {
 	int out;
 
-	ftrace_arch_code_modify_prepare();
+	mutex_lock(&text_mutex);
 	out = ftrace_make_nop(mod, rec, MCOUNT_ADDR);
-	ftrace_arch_code_modify_post_process();
+	mutex_unlock(&text_mutex);
 
 	return out;
 }
@@ -146,10 +129,10 @@
 int ftrace_update_ftrace_func(ftrace_func_t func)
 {
 	int ret = __ftrace_modify_call((unsigned long)&ftrace_call,
-				       (unsigned long)func, true);
+				       (unsigned long)func, true, true);
 	if (!ret) {
 		ret = __ftrace_modify_call((unsigned long)&ftrace_regs_call,
-					   (unsigned long)func, true);
+					   (unsigned long)func, true, true);
 	}
 
 	return ret;
@@ -166,16 +149,16 @@
 		       unsigned long addr)
 {
 	unsigned int call[2];
-	unsigned long caller = rec->ip + FUNC_ENTRY_JMP;
+	unsigned long caller = rec->ip;
 	int ret;
 
-	make_call(caller, old_addr, call);
+	make_call_t0(caller, old_addr, call);
 	ret = ftrace_check_current_call(caller, call);
 
 	if (ret)
 		return ret;
 
-	return __ftrace_modify_call(caller, addr, true);
+	return __ftrace_modify_call(caller, addr, true, false);
 }
 #endif
 
@@ -210,12 +193,12 @@
 	int ret;
 
 	ret = __ftrace_modify_call((unsigned long)&ftrace_graph_call,
-				    (unsigned long)&prepare_ftrace_return, true);
+				    (unsigned long)&prepare_ftrace_return, true, true);
 	if (ret)
 		return ret;
 
 	return __ftrace_modify_call((unsigned long)&ftrace_graph_regs_call,
-				    (unsigned long)&prepare_ftrace_return, true);
+				    (unsigned long)&prepare_ftrace_return, true, true);
 }
 
 int ftrace_disable_ftrace_graph_caller(void)
@@ -223,12 +206,12 @@
 	int ret;
 
 	ret = __ftrace_modify_call((unsigned long)&ftrace_graph_call,
-				    (unsigned long)&prepare_ftrace_return, false);
+				    (unsigned long)&prepare_ftrace_return, false, true);
 	if (ret)
 		return ret;
 
 	return __ftrace_modify_call((unsigned long)&ftrace_graph_regs_call,
-				    (unsigned long)&prepare_ftrace_return, false);
+				    (unsigned long)&prepare_ftrace_return, false, true);
 }
 #endif /* CONFIG_DYNAMIC_FTRACE */
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/head.S
@@ -301,6 +301,7 @@
 	REG_S a0, (a2)
 
 	/* Initialize page tables and relocate to virtual addresses */
+	la tp, init_task
 	la sp, init_thread_union + THREAD_SIZE
 	XIP_FIXUP_OFFSET sp
 #ifdef CONFIG_BUILTIN_DTB
@@ -308,6 +309,9 @@
 #else
 	mv a0, s1
 #endif /* CONFIG_BUILTIN_DTB */
+	/* Set trap vector to spin forever to help debug */
+	la a3, .Lsecondary_park
+	csrw CSR_TVEC, a3
 	call setup_vm
 #ifdef CONFIG_MMU
 	la a0, early_pg_dir
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/kexec_relocate.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/kexec_relocate.S
@@ -159,25 +159,15 @@
 	 * s0: (const) Phys address to jump to
 	 * s1: (const) Phys address of the FDT image
 	 * s2: (const) The hartid of the current hart
-	 * s3: (const) kernel_map.va_pa_offset, used when switching MMU off
 	 */
 	mv	s0, a1
 	mv	s1, a2
 	mv	s2, a3
-	mv	s3, a4
 
 	/* Disable / cleanup interrupts */
 	csrw	CSR_SIE, zero
 	csrw	CSR_SIP, zero
 
-	/* Switch to physical addressing */
-	la	s4, 1f
-	sub	s4, s4, s3
-	csrw	CSR_STVEC, s4
-	csrw	CSR_SATP, zero
-
-.align 2
-1:
 	/* Pass the arguments to the next kernel  / Cleanup*/
 	mv	a0, s2
 	mv	a1, s1
@@ -214,7 +204,15 @@
 	csrw	CSR_SCAUSE, zero
 	csrw	CSR_SSCRATCH, zero
 
-	jalr	zero, a2, 0
+	/*
+	 * Switch to physical addressing
+	 * This will also trigger a jump to CSR_STVEC
+	 * which in this case is the address of the new
+	 * kernel.
+	 */
+	csrw	CSR_STVEC, a2
+	csrw	CSR_SATP, zero
+
 SYM_CODE_END(riscv_kexec_norelocate)
 
 .section ".rodata"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/machine_kexec.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/machine_kexec.c
@@ -15,6 +15,8 @@
 #include <linux/compiler.h>	/* For unreachable() */
 #include <linux/cpu.h>		/* For cpu_down() */
 #include <linux/reboot.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
 
 /*
  * kexec_image_info - Print received image details
@@ -65,7 +67,9 @@
 		if (image->segment[i].memsz <= sizeof(fdt))
 			continue;
 
-		if (copy_from_user(&fdt, image->segment[i].buf, sizeof(fdt)))
+		if (image->file_mode)
+			memcpy(&fdt, image->segment[i].buf, sizeof(fdt));
+		else if (copy_from_user(&fdt, image->segment[i].buf, sizeof(fdt)))
 			continue;
 
 		if (fdt_check_header(&fdt))
@@ -136,19 +140,62 @@
 #endif
 }
 
+/* Override the weak function in kernel/panic.c */
+void crash_smp_send_stop(void)
+{
+	static int cpus_stopped;
+
+	/*
+	 * This function can be called twice in panic path, but obviously
+	 * we execute this only once.
+	 */
+	if (cpus_stopped)
+		return;
+
+	smp_send_stop();
+	cpus_stopped = 1;
+}
+
+static void machine_kexec_mask_interrupts(void)
+{
+	unsigned int i;
+	struct irq_desc *desc;
+
+	for_each_irq_desc(i, desc) {
+		struct irq_chip *chip;
+
+		chip = irq_desc_get_chip(desc);
+		if (!chip)
+			continue;
+
+		if (chip->irq_eoi && irqd_irq_inprogress(&desc->irq_data))
+			chip->irq_eoi(&desc->irq_data);
+
+		if (chip->irq_mask)
+			chip->irq_mask(&desc->irq_data);
+
+		if (chip->irq_disable && !irqd_irq_disabled(&desc->irq_data))
+			chip->irq_disable(&desc->irq_data);
+	}
+}
+
 /*
  * machine_crash_shutdown - Prepare to kexec after a kernel crash
  *
  * This function is called by crash_kexec just before machine_kexec
- * below and its goal is similar to machine_shutdown, but in case of
- * a kernel crash. Since we don't handle such cases yet, this function
- * is empty.
+ * and its goal is to shutdown non-crashing cpus and save registers.
  */
 void
 machine_crash_shutdown(struct pt_regs *regs)
 {
+	local_irq_disable();
+
+	/* shutdown non-crashing cpus */
+	crash_smp_send_stop();
+
 	crash_save_cpu(regs, smp_processor_id());
-	machine_shutdown();
+	machine_kexec_mask_interrupts();
+
 	pr_info("Starting crashdump kernel...\n");
 }
 
@@ -169,7 +216,8 @@
 	struct kimage_arch *internal = &image->arch;
 	unsigned long jump_addr = (unsigned long) image->start;
 	unsigned long first_ind_entry = (unsigned long) &image->head;
-	unsigned long this_hart_id = raw_smp_processor_id();
+	unsigned long this_cpu_id = __smp_processor_id();
+	unsigned long this_hart_id = cpuid_to_hartid_map(this_cpu_id);
 	unsigned long fdt_addr = internal->fdt_addr;
 	void *control_code_buffer = page_address(image->control_code_page);
 	riscv_kexec_method kexec_method = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/mcount-dyn.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/mcount-dyn.S
@@ -13,8 +13,8 @@
 
 	.text
 
-#define FENTRY_RA_OFFSET	12
-#define ABI_SIZE_ON_STACK	72
+#define FENTRY_RA_OFFSET	8
+#define ABI_SIZE_ON_STACK	80
 #define ABI_A0			0
 #define ABI_A1			8
 #define ABI_A2			16
@@ -23,10 +23,10 @@
 #define ABI_A5			40
 #define ABI_A6			48
 #define ABI_A7			56
-#define ABI_RA			64
+#define ABI_T0			64
+#define ABI_RA			72
 
 	.macro SAVE_ABI
-	addi	sp, sp, -SZREG
 	addi	sp, sp, -ABI_SIZE_ON_STACK
 
 	REG_S	a0, ABI_A0(sp)
@@ -37,6 +37,7 @@
 	REG_S	a5, ABI_A5(sp)
 	REG_S	a6, ABI_A6(sp)
 	REG_S	a7, ABI_A7(sp)
+	REG_S	t0, ABI_T0(sp)
 	REG_S	ra, ABI_RA(sp)
 	.endm
 
@@ -49,24 +50,18 @@
 	REG_L	a5, ABI_A5(sp)
 	REG_L	a6, ABI_A6(sp)
 	REG_L	a7, ABI_A7(sp)
+	REG_L	t0, ABI_T0(sp)
 	REG_L	ra, ABI_RA(sp)
 
 	addi	sp, sp, ABI_SIZE_ON_STACK
-	addi	sp, sp, SZREG
 	.endm
 
 #ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
 	.macro SAVE_ALL
-	addi	sp, sp, -SZREG
 	addi	sp, sp, -PT_SIZE_ON_STACK
 
-	REG_S x1,  PT_EPC(sp)
-	addi	sp, sp, PT_SIZE_ON_STACK
-	REG_L x1,  (sp)
-	addi	sp, sp, -PT_SIZE_ON_STACK
+	REG_S t0,  PT_EPC(sp)
 	REG_S x1,  PT_RA(sp)
-	REG_L x1,  PT_EPC(sp)
-
 	REG_S x2,  PT_SP(sp)
 	REG_S x3,  PT_GP(sp)
 	REG_S x4,  PT_TP(sp)
@@ -100,15 +95,11 @@
 	.endm
 
 	.macro RESTORE_ALL
+	REG_L t0,  PT_EPC(sp)
 	REG_L x1,  PT_RA(sp)
-	addi	sp, sp, PT_SIZE_ON_STACK
-	REG_S x1,  (sp)
-	addi	sp, sp, -PT_SIZE_ON_STACK
-	REG_L x1,  PT_EPC(sp)
 	REG_L x2,  PT_SP(sp)
 	REG_L x3,  PT_GP(sp)
 	REG_L x4,  PT_TP(sp)
-	REG_L x5,  PT_T0(sp)
 	REG_L x6,  PT_T1(sp)
 	REG_L x7,  PT_T2(sp)
 	REG_L x8,  PT_S0(sp)
@@ -137,17 +128,16 @@
 	REG_L x31, PT_T6(sp)
 
 	addi	sp, sp, PT_SIZE_ON_STACK
-	addi	sp, sp, SZREG
 	.endm
 #endif /* CONFIG_DYNAMIC_FTRACE_WITH_REGS */
 
 ENTRY(ftrace_caller)
 	SAVE_ABI
 
-	addi	a0, ra, -FENTRY_RA_OFFSET
+	addi	a0, t0, -FENTRY_RA_OFFSET
 	la	a1, function_trace_op
 	REG_L	a2, 0(a1)
-	REG_L	a1, ABI_SIZE_ON_STACK(sp)
+	mv	a1, ra
 	mv	a3, sp
 
 ftrace_call:
@@ -155,8 +145,8 @@
 	call	ftrace_stub
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
-	addi	a0, sp, ABI_SIZE_ON_STACK
-	REG_L	a1, ABI_RA(sp)
+	addi	a0, sp, ABI_RA
+	REG_L	a1, ABI_T0(sp)
 	addi	a1, a1, -FENTRY_RA_OFFSET
 #ifdef HAVE_FUNCTION_GRAPH_FP_TEST
 	mv	a2, s0
@@ -166,17 +156,17 @@
 	call	ftrace_stub
 #endif
 	RESTORE_ABI
-	ret
+	jr t0
 ENDPROC(ftrace_caller)
 
 #ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
 ENTRY(ftrace_regs_caller)
 	SAVE_ALL
 
-	addi	a0, ra, -FENTRY_RA_OFFSET
+	addi	a0, t0, -FENTRY_RA_OFFSET
 	la	a1, function_trace_op
 	REG_L	a2, 0(a1)
-	REG_L	a1, PT_SIZE_ON_STACK(sp)
+	mv	a1, ra
 	mv	a3, sp
 
 ftrace_regs_call:
@@ -196,6 +186,6 @@
 #endif
 
 	RESTORE_ALL
-	ret
+	jr t0
 ENDPROC(ftrace_regs_caller)
 #endif /* CONFIG_DYNAMIC_FTRACE_WITH_REGS */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/module.c
@@ -13,6 +13,19 @@
 #include <linux/pgtable.h>
 #include <asm/sections.h>
 
+/*
+ * The auipc+jalr instruction pair can reach any PC-relative offset
+ * in the range [-2^31 - 2^11, 2^31 - 2^11)
+ */
+static bool riscv_insn_valid_32bit_offset(ptrdiff_t val)
+{
+#ifdef CONFIG_32BIT
+	return true;
+#else
+	return (-(1L << 31) - (1L << 11)) <= val && val < ((1L << 31) - (1L << 11));
+#endif
+}
+
 static int apply_r_riscv_32_rela(struct module *me, u32 *location, Elf_Addr v)
 {
 	if (v != (u32)v) {
@@ -95,7 +108,7 @@
 	ptrdiff_t offset = (void *)v - (void *)location;
 	s32 hi20;
 
-	if (offset != (s32)offset) {
+	if (!riscv_insn_valid_32bit_offset(offset)) {
 		pr_err(
 		  "%s: target %016llx can not be addressed by the 32-bit offset from PC = %p\n",
 		  me->name, (long long)v, location);
@@ -197,10 +210,9 @@
 				       Elf_Addr v)
 {
 	ptrdiff_t offset = (void *)v - (void *)location;
-	s32 fill_v = offset;
 	u32 hi20, lo12;
 
-	if (offset != fill_v) {
+	if (!riscv_insn_valid_32bit_offset(offset)) {
 		/* Only emit the plt entry if offset over 32-bit range */
 		if (IS_ENABLED(CONFIG_MODULE_SECTIONS)) {
 			offset = module_emit_plt_entry(me, v);
@@ -224,10 +236,9 @@
 				   Elf_Addr v)
 {
 	ptrdiff_t offset = (void *)v - (void *)location;
-	s32 fill_v = offset;
 	u32 hi20, lo12;
 
-	if (offset != fill_v) {
+	if (!riscv_insn_valid_32bit_offset(offset)) {
 		pr_err(
 		  "%s: target %016llx can not be addressed by the 32-bit offset from PC = %p\n",
 		  me->name, (long long)v, location);
@@ -412,7 +423,8 @@
 {
 	return __vmalloc_node_range(size, 1, MODULES_VADDR,
 				    MODULES_END, GFP_KERNEL,
-				    PAGE_KERNEL, 0, NUMA_NO_NODE,
+				    PAGE_KERNEL, VM_FLUSH_RESET_PERMS,
+				    NUMA_NO_NODE,
 				    __builtin_return_address(0));
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/patch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/patch.c
@@ -11,7 +11,9 @@
 #include <asm/kprobes.h>
 #include <asm/cacheflush.h>
 #include <asm/fixmap.h>
+#include <asm/ftrace.h>
 #include <asm/patch.h>
+#include <asm/sections.h>
 
 struct patch_insn {
 	void *addr;
@@ -19,7 +21,17 @@
 	atomic_t cpu_count;
 };
 
+int riscv_patch_in_stop_machine = false;
+
 #ifdef CONFIG_MMU
+
+static inline bool is_kernel_exittext(uintptr_t addr)
+{
+	return system_state < SYSTEM_RUNNING &&
+		addr >= (uintptr_t)__exittext_begin &&
+		addr < (uintptr_t)__exittext_end;
+}
+
 /*
  * The fix_to_virt(, idx) needs a const value (not a dynamic variable of
  * reg-a0) or BUILD_BUG_ON failed with "idx >= __end_of_fixed_addresses".
@@ -30,7 +42,7 @@
 	uintptr_t uintaddr = (uintptr_t) addr;
 	struct page *page;
 
-	if (core_kernel_text(uintaddr))
+	if (core_kernel_text(uintaddr) || is_kernel_exittext(uintaddr))
 		page = phys_to_page(__pa_symbol(addr));
 	else if (IS_ENABLED(CONFIG_STRICT_MODULE_RWX))
 		page = vmalloc_to_page(addr);
@@ -59,8 +71,15 @@
 	 * Before reaching here, it was expected to lock the text_mutex
 	 * already, so we don't need to give another lock here and could
 	 * ensure that it was safe between each cores.
+	 *
+	 * We're currently using stop_machine() for ftrace & kprobes, and while
+	 * that ensures text_mutex is held before installing the mappings it
+	 * does not ensure text_mutex is held by the calling thread.  That's
+	 * safe but triggers a lockdep failure, so just elide it for that
+	 * specific case.
 	 */
-	lockdep_assert_held(&text_mutex);
+	if (!riscv_patch_in_stop_machine)
+		lockdep_assert_held(&text_mutex);
 
 	if (across_pages)
 		patch_map(addr + len, FIX_TEXT_POKE1);
@@ -104,7 +123,7 @@
 	struct patch_insn *patch = data;
 	int ret = 0;
 
-	if (atomic_inc_return(&patch->cpu_count) == 1) {
+	if (atomic_inc_return(&patch->cpu_count) == num_online_cpus()) {
 		ret =
 		    patch_text_nosync(patch->addr, &patch->insn,
 					    GET_INSN_LENGTH(patch->insn));
@@ -121,13 +140,25 @@
 
 int patch_text(void *addr, u32 insn)
 {
+	int ret;
 	struct patch_insn patch = {
 		.addr = addr,
 		.insn = insn,
 		.cpu_count = ATOMIC_INIT(0),
 	};
 
-	return stop_machine_cpuslocked(patch_text_cb,
-				       &patch, cpu_online_mask);
+	/*
+	 * kprobes takes text_mutex, before calling patch_text(), but as we call
+	 * calls stop_machine(), the lockdep assertion in patch_insn_write()
+	 * gets confused by the context in which the lock is taken.
+	 * Instead, ensure the lock is held before calling stop_machine(), and
+	 * set riscv_patch_in_stop_machine to skip the check in
+	 * patch_insn_write().
+	 */
+	lockdep_assert_held(&text_mutex);
+	riscv_patch_in_stop_machine = true;
+	ret = stop_machine_cpuslocked(patch_text_cb, &patch, cpu_online_mask);
+	riscv_patch_in_stop_machine = false;
+	return ret;
 }
 NOKPROBE_SYMBOL(patch_text);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/perf_callchain.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/perf_callchain.c
@@ -15,8 +15,8 @@
 {
 	struct stackframe buftail;
 	unsigned long ra = 0;
-	unsigned long *user_frame_tail =
-			(unsigned long *)(fp - sizeof(struct stackframe));
+	unsigned long __user *user_frame_tail =
+		(unsigned long __user *)(fp - sizeof(struct stackframe));
 
 	/* Check accessibility of one struct frame_tail beyond */
 	if (!access_ok(user_frame_tail, sizeof(buftail)))
@@ -56,30 +56,33 @@
 void perf_callchain_user(struct perf_callchain_entry_ctx *entry,
 			 struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	unsigned long fp = 0;
 
 	/* RISC-V does not support perf in guest mode. */
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
+	if (guest_cbs && guest_cbs->is_in_guest())
 		return;
 
 	fp = regs->s0;
 	perf_callchain_store(entry, regs->epc);
 
 	fp = user_backtrace(entry, fp, regs->ra);
-	while (fp && !(fp & 0x3) && entry->nr < entry->max_stack)
+	while (fp && !(fp & 0x7) && entry->nr < entry->max_stack)
 		fp = user_backtrace(entry, fp, 0);
 }
 
 static bool fill_callchain(void *entry, unsigned long pc)
 {
-	return perf_callchain_store(entry, pc);
+	return perf_callchain_store(entry, pc) == 0;
 }
 
 void perf_callchain_kernel(struct perf_callchain_entry_ctx *entry,
 			   struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
+
 	/* RISC-V does not support perf in guest mode. */
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		pr_warn("RISC-V does not support perf in guest mode!");
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/probes/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/probes/kprobes.c
@@ -1,5 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/kprobes.h>
 #include <linux/extable.h>
 #include <linux/slab.h>
@@ -46,18 +48,35 @@
 	post_kprobe_handler(p, kcb, regs);
 }
 
-int __kprobes arch_prepare_kprobe(struct kprobe *p)
+static bool __kprobes arch_check_kprobe(struct kprobe *p)
 {
-	unsigned long probe_addr = (unsigned long)p->addr;
+	unsigned long tmp  = (unsigned long)p->addr - p->offset;
+	unsigned long addr = (unsigned long)p->addr;
 
-	if (probe_addr & 0x1) {
-		pr_warn("Address not aligned.\n");
+	while (tmp <= addr) {
+		if (tmp == addr)
+			return true;
 
-		return -EINVAL;
+		tmp += GET_INSN_LENGTH(*(u16 *)tmp);
 	}
 
+	return false;
+}
+
+int __kprobes arch_prepare_kprobe(struct kprobe *p)
+{
+	u16 *insn = (u16 *)p->addr;
+
+	if ((unsigned long)insn & 0x1)
+		return -EILSEQ;
+
+	if (!arch_check_kprobe(p))
+		return -EILSEQ;
+
 	/* copy instruction */
-	p->opcode = *p->addr;
+	p->opcode = (kprobe_opcode_t)(*insn++);
+	if (GET_INSN_LENGTH(p->opcode) == 4)
+		p->opcode |= (kprobe_opcode_t)(*insn) << 16;
 
 	/* decode instruction */
 	switch (riscv_probe_decode_insn(p->addr, &p->ainsn.api)) {
@@ -191,7 +210,7 @@
 		break;
 	case KPROBE_HIT_SS:
 	case KPROBE_REENTER:
-		pr_warn("Unrecoverable kprobe detected.\n");
+		pr_warn("Failed to recover from reentered kprobes.\n");
 		dump_kprobe(p);
 		BUG();
 		break;
@@ -348,7 +367,7 @@
 
 void __kprobes __used *trampoline_probe_handler(struct pt_regs *regs)
 {
-	return (void *)kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	return (void *)kretprobe_trampoline_handler(regs, NULL);
 }
 
 void __kprobes arch_prepare_kretprobe(struct kretprobe_instance *ri,
@@ -356,7 +375,7 @@
 {
 	ri->ret_addr = (kprobe_opcode_t *)regs->ra;
 	ri->fp = NULL;
-	regs->ra = (unsigned long) &kretprobe_trampoline;
+	regs->ra = (unsigned long) &__kretprobe_trampoline;
 }
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/probes/kprobes_trampoline.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/probes/kprobes_trampoline.S
@@ -75,7 +75,7 @@
 	REG_L x31, PT_T6(sp)
 	.endm
 
-ENTRY(kretprobe_trampoline)
+ENTRY(__kretprobe_trampoline)
 	addi sp, sp, -(PT_SIZE_ON_STACK)
 	save_all_base_regs
 
@@ -90,4 +90,4 @@
 	addi sp, sp, PT_SIZE_ON_STACK
 
 	ret
-ENDPROC(kretprobe_trampoline)
+ENDPROC(__kretprobe_trampoline)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/probes/simulate-insn.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/probes/simulate-insn.c
@@ -24,7 +24,7 @@
 				       unsigned long val)
 {
 	if (index == 0)
-		return false;
+		return true;
 	else if (index <= 31)
 		*((unsigned long *)regs + index) = val;
 	else
@@ -71,11 +71,11 @@
 	u32 rd_index = (opcode >> 7) & 0x1f;
 	u32 rs1_index = (opcode >> 15) & 0x1f;
 
-	ret = rv_insn_reg_set_val(regs, rd_index, addr + 4);
+	ret = rv_insn_reg_get_val(regs, rs1_index, &base_addr);
 	if (!ret)
 		return ret;
 
-	ret = rv_insn_reg_get_val(regs, rs1_index, &base_addr);
+	ret = rv_insn_reg_set_val(regs, rd_index, addr + 4);
 	if (!ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/probes/simulate-insn.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/probes/simulate-insn.h
@@ -31,9 +31,9 @@
 	} while (0)
 
 __RISCV_INSN_FUNCS(c_j,		0xe003, 0xa001);
-__RISCV_INSN_FUNCS(c_jr,	0xf007, 0x8002);
+__RISCV_INSN_FUNCS(c_jr,	0xf07f, 0x8002);
 __RISCV_INSN_FUNCS(c_jal,	0xe003, 0x2001);
-__RISCV_INSN_FUNCS(c_jalr,	0xf007, 0x9002);
+__RISCV_INSN_FUNCS(c_jalr,	0xf07f, 0x9002);
 __RISCV_INSN_FUNCS(c_beqz,	0xe003, 0xc001);
 __RISCV_INSN_FUNCS(c_bnez,	0xe003, 0xe001);
 __RISCV_INSN_FUNCS(c_ebreak,	0xffff, 0x9002);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/probes/uprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/probes/uprobes.c
@@ -59,8 +59,6 @@
 
 	instruction_pointer_set(regs, utask->xol_vaddr);
 
-	regs->status &= ~SR_SPIE;
-
 	return 0;
 }
 
@@ -69,11 +67,10 @@
 	struct uprobe_task *utask = current->utask;
 
 	WARN_ON_ONCE(current->thread.bad_cause != UPROBE_TRAP_NR);
+	current->thread.bad_cause = utask->autask.saved_cause;
 
 	instruction_pointer_set(regs, utask->vaddr + auprobe->insn_size);
 
-	regs->status |= SR_SPIE;
-
 	return 0;
 }
 
@@ -106,13 +103,12 @@
 {
 	struct uprobe_task *utask = current->utask;
 
+	current->thread.bad_cause = utask->autask.saved_cause;
 	/*
 	 * Task has received a fatal signal, so reset back to probbed
 	 * address.
 	 */
 	instruction_pointer_set(regs, utask->vaddr);
-
-	regs->status &= ~SR_SPIE;
 }
 
 bool arch_uretprobe_is_alive(struct return_instance *ret, enum rp_check ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/process.c
@@ -24,8 +24,6 @@
 #include <asm/switch_to.h>
 #include <asm/thread_info.h>
 
-register unsigned long gp_in_global __asm__("gp");
-
 #if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_STACKPROTECTOR_PER_TASK)
 #include <linux/stackprotector.h>
 unsigned long __stack_chk_guard __read_mostly;
@@ -124,11 +122,12 @@
 {
 	struct pt_regs *childregs = task_pt_regs(p);
 
+	memset(&p->thread.s, 0, sizeof(p->thread.s));
+
 	/* p->thread holds context to be restored by __switch_to() */
 	if (unlikely(p->flags & (PF_KTHREAD | PF_IO_WORKER))) {
 		/* Kernel thread */
 		memset(childregs, 0, sizeof(struct pt_regs));
-		childregs->gp = gp_in_global;
 		/* Supervisor/Machine, irqs on: */
 		childregs->status = SR_PP | SR_PIE;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/reset.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/reset.c
@@ -12,7 +12,7 @@
 		wait_for_interrupt();
 }
 
-void (*pm_power_off)(void) = default_power_off;
+void (*pm_power_off)(void) = NULL;
 EXPORT_SYMBOL(pm_power_off);
 
 void machine_restart(char *cmd)
@@ -23,10 +23,16 @@
 
 void machine_halt(void)
 {
-	pm_power_off();
+	if (pm_power_off != NULL)
+		pm_power_off();
+	else
+		default_power_off();
 }
 
 void machine_power_off(void)
 {
-	pm_power_off();
+	if (pm_power_off != NULL)
+		pm_power_off();
+	else
+		default_power_off();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/setup.c
@@ -59,6 +59,16 @@
 unsigned long boot_cpu_hartid;
 static DEFINE_PER_CPU(struct cpu, cpu_devices);
 
+void riscv_cpuid_to_hartid_mask(const struct cpumask *in, struct cpumask *out)
+{
+	int cpu;
+
+	cpumask_clear(out);
+	for_each_cpu(cpu, in)
+		cpumask_set_cpu(cpuid_to_hartid_map(cpu), out);
+}
+EXPORT_SYMBOL_GPL(riscv_cpuid_to_hartid_mask);
+
 /*
  * Place kernel memory regions on the resource tree so that
  * kexec-tools can retrieve them from /proc/iomem. While there
@@ -189,7 +199,7 @@
 		res = &mem_res[res_idx--];
 
 		res->name = "Reserved";
-		res->flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+		res->flags = IORESOURCE_MEM | IORESOURCE_EXCLUSIVE;
 		res->start = __pfn_to_phys(memblock_region_reserved_base_pfn(region));
 		res->end = __pfn_to_phys(memblock_region_reserved_end_pfn(region)) - 1;
 
@@ -214,7 +224,7 @@
 
 		if (unlikely(memblock_is_nomap(region))) {
 			res->name = "Reserved";
-			res->flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+			res->flags = IORESOURCE_MEM | IORESOURCE_EXCLUSIVE;
 		} else {
 			res->name = "System RAM";
 			res->flags = IORESOURCE_SYSTEM_RAM | IORESOURCE_BUSY;
@@ -250,10 +260,10 @@
 			pr_info("Machine model: %s\n", name);
 			dump_stack_set_arch_desc("%s (DT)", name);
 		}
-		return;
+	} else {
+		pr_err("No DTB passed to the kernel\n");
 	}
 
-	pr_err("No DTB passed to the kernel\n");
 #ifdef CONFIG_CMDLINE_FORCE
 	strscpy(boot_command_line, CONFIG_CMDLINE, COMMAND_LINE_SIZE);
 	pr_info("Forcing kernel command line to: %s\n", boot_command_line);
@@ -276,10 +286,7 @@
 #if IS_ENABLED(CONFIG_BUILTIN_DTB)
 	unflatten_and_copy_device_tree();
 #else
-	if (early_init_dt_verify(__va(XIP_FIXUP(dtb_early_pa))))
-		unflatten_device_tree();
-	else
-		pr_err("No DTB found in kernel mappings\n");
+	unflatten_device_tree();
 #endif
 	misc_mem_init();
 
@@ -320,10 +327,11 @@
 
 void free_initmem(void)
 {
-	if (IS_ENABLED(CONFIG_STRICT_KERNEL_RWX))
-		set_kernel_memory(lm_alias(__init_begin), lm_alias(__init_end),
-				  IS_ENABLED(CONFIG_64BIT) ?
-					set_memory_rw : set_memory_rw_nx);
+	if (IS_ENABLED(CONFIG_STRICT_KERNEL_RWX)) {
+		set_kernel_memory(lm_alias(__init_begin), lm_alias(__init_end), set_memory_rw_nx);
+		if (IS_ENABLED(CONFIG_64BIT))
+			set_kernel_memory(__init_begin, __init_end, set_memory_nx);
+	}
 
 	free_initmem_default(POISON_FREE_INITMEM);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/signal.c
@@ -16,6 +16,7 @@
 #include <asm/vdso.h>
 #include <asm/switch_to.h>
 #include <asm/csr.h>
+#include <asm/cacheflush.h>
 
 extern u32 __user_rt_sigreturn[2];
 
@@ -121,6 +122,8 @@
 	if (restore_altstack(&frame->uc.uc_stack))
 		goto badframe;
 
+	regs->cause = -1UL;
+
 	return regs->a0;
 
 badframe:
@@ -176,6 +179,7 @@
 {
 	struct rt_sigframe __user *frame;
 	long err = 0;
+	unsigned long __maybe_unused addr;
 
 	frame = get_sigframe(ksig, regs, sizeof(*frame));
 	if (!access_ok(frame, sizeof(*frame)))
@@ -204,7 +208,12 @@
 	if (copy_to_user(&frame->sigreturn_code, __user_rt_sigreturn,
 			 sizeof(frame->sigreturn_code)))
 		return -EFAULT;
-	regs->ra = (unsigned long)&frame->sigreturn_code;
+
+	addr = (unsigned long)&frame->sigreturn_code;
+	/* Make sure the two instructions are pushed to icache. */
+	flush_icache_range(addr, addr + sizeof(frame->sigreturn_code));
+
+	regs->ra = addr;
 #endif /* CONFIG_MMU */
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/smp.c
@@ -59,16 +59,6 @@
 	return -ENOENT;
 }
 
-void riscv_cpuid_to_hartid_mask(const struct cpumask *in, struct cpumask *out)
-{
-	int cpu;
-
-	cpumask_clear(out);
-	for_each_cpu(cpu, in)
-		cpumask_set_cpu(cpuid_to_hartid_map(cpu), out);
-}
-EXPORT_SYMBOL_GPL(riscv_cpuid_to_hartid_mask);
-
 bool arch_match_cpu_phys_id(int cpu, u64 phys_id)
 {
 	return phys_id == cpuid_to_hartid_map(cpu);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/smpboot.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/smpboot.c
@@ -53,6 +53,7 @@
 	unsigned int curr_cpuid;
 
 	curr_cpuid = smp_processor_id();
+	store_cpu_topology(curr_cpuid);
 	numa_store_cpu_info(curr_cpuid);
 	numa_add_cpu(curr_cpuid);
 
@@ -165,9 +166,9 @@
 	mmgrab(mm);
 	current->active_mm = mm;
 
+	store_cpu_topology(curr_cpuid);
 	notify_cpu_starting(curr_cpuid);
 	numa_add_cpu(curr_cpuid);
-	update_siblings_masks(curr_cpuid);
 	set_cpu_online(curr_cpuid, 1);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/stacktrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/stacktrace.c
@@ -18,19 +18,34 @@
 
 #ifdef CONFIG_FRAME_POINTER
 
+extern asmlinkage void ret_from_exception(void);
+
+static inline int fp_is_valid(unsigned long fp, unsigned long sp)
+{
+	unsigned long low, high;
+
+	low = sp + sizeof(struct stackframe);
+	high = ALIGN(sp, THREAD_SIZE);
+
+	return !(fp < low || fp > high || fp & 0x07);
+}
+
 void notrace walk_stackframe(struct task_struct *task, struct pt_regs *regs,
 			     bool (*fn)(void *, unsigned long), void *arg)
 {
 	unsigned long fp, sp, pc;
+	int graph_idx = 0;
+	int level = 0;
 
 	if (regs) {
 		fp = frame_pointer(regs);
 		sp = user_stack_pointer(regs);
 		pc = instruction_pointer(regs);
 	} else if (task == NULL || task == current) {
-		fp = (unsigned long)__builtin_frame_address(1);
-		sp = (unsigned long)__builtin_frame_address(0);
-		pc = (unsigned long)__builtin_return_address(0);
+		fp = (unsigned long)__builtin_frame_address(0);
+		sp = sp_in_global;
+		pc = (unsigned long)walk_stackframe;
+		level = -1;
 	} else {
 		/* task blocked in __switch_to */
 		fp = task->thread.s[0];
@@ -39,27 +54,32 @@
 	}
 
 	for (;;) {
-		unsigned long low, high;
 		struct stackframe *frame;
 
-		if (unlikely(!__kernel_text_address(pc) || !fn(arg, pc)))
+		if (unlikely(!__kernel_text_address(pc) || (level++ >= 0 && !fn(arg, pc))))
 			break;
 
-		/* Validate frame pointer */
-		low = sp + sizeof(struct stackframe);
-		high = ALIGN(sp, THREAD_SIZE);
-		if (unlikely(fp < low || fp > high || fp & 0x7))
+		if (unlikely(!fp_is_valid(fp, sp)))
 			break;
+
 		/* Unwind stack frame */
 		frame = (struct stackframe *)fp - 1;
 		sp = fp;
-		if (regs && (regs->epc == pc) && (frame->fp & 0x7)) {
+		if (regs && (regs->epc == pc) && fp_is_valid(frame->ra, sp)) {
+			/* We hit function where ra is not saved on the stack */
 			fp = frame->ra;
 			pc = regs->ra;
 		} else {
 			fp = frame->fp;
-			pc = ftrace_graph_ret_addr(current, NULL, frame->ra,
-						   (unsigned long *)(fp - 8));
+			pc = ftrace_graph_ret_addr(current, &graph_idx, frame->ra,
+						   &frame->ra);
+			if (pc == (unsigned long)ret_from_exception) {
+				if (unlikely(!__kernel_text_address(pc) || !fn(arg, pc)))
+					break;
+
+				pc = ((struct pt_regs *)sp)->epc;
+				fp = ((struct pt_regs *)sp)->s0;
+			}
 		}
 
 	}
@@ -92,7 +112,7 @@
 	while (!kstack_end(ksp)) {
 		if (__kernel_text_address(pc) && unlikely(!fn(arg, pc)))
 			break;
-		pc = (*ksp++) - 0x4;
+		pc = READ_ONCE_NOCHECK(*ksp++) - 0x4;
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/time.c
@@ -5,6 +5,7 @@
  */
 
 #include <linux/of_clk.h>
+#include <linux/clockchips.h>
 #include <linux/clocksource.h>
 #include <linux/delay.h>
 #include <asm/sbi.h>
@@ -29,6 +30,8 @@
 
 	of_clk_init(NULL);
 	timer_probe();
+
+	tick_setup_hrtimer_broadcast();
 }
 
 void clocksource_arch_init(struct clocksource *cs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/trace_irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/trace_irq.c
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Changbin Du <changbin.du@gmail.com>
+ */
+
+#include <linux/irqflags.h>
+#include <linux/kprobes.h>
+#include "trace_irq.h"
+
+/*
+ * trace_hardirqs_on/off require the caller to setup frame pointer properly.
+ * Otherwise, CALLER_ADDR1 might trigger an pagging exception in kernel.
+ * Here we add one extra level so they can be safely called by low
+ * level entry code which $fp is used for other purpose.
+ */
+
+void __trace_hardirqs_on(void)
+{
+	trace_hardirqs_on();
+}
+NOKPROBE_SYMBOL(__trace_hardirqs_on);
+
+void __trace_hardirqs_off(void)
+{
+	trace_hardirqs_off();
+}
+NOKPROBE_SYMBOL(__trace_hardirqs_off);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/trace_irq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/trace_irq.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Changbin Du <changbin.du@gmail.com>
+ */
+#ifndef __TRACE_IRQ_H
+#define __TRACE_IRQ_H
+
+void __trace_hardirqs_on(void);
+void __trace_hardirqs_off(void);
+
+#endif /* __TRACE_IRQ_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/traps.c
@@ -16,37 +16,46 @@
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/irq.h>
+#include <linux/kexec.h>
 
 #include <asm/asm-prototypes.h>
 #include <asm/bug.h>
+#include <asm/csr.h>
 #include <asm/processor.h>
 #include <asm/ptrace.h>
-#include <asm/csr.h>
+#include <asm/thread_info.h>
 
 int show_unhandled_signals = 1;
 
-static DEFINE_SPINLOCK(die_lock);
+static DEFINE_RAW_SPINLOCK(die_lock);
 
 void die(struct pt_regs *regs, const char *str)
 {
 	static int die_counter;
 	int ret;
+	long cause;
+	unsigned long flags;
 
 	oops_enter();
 
-	spin_lock_irq(&die_lock);
+	raw_spin_lock_irqsave(&die_lock, flags);
 	console_verbose();
 	bust_spinlocks(1);
 
 	pr_emerg("%s [#%d]\n", str, ++die_counter);
 	print_modules();
-	show_regs(regs);
+	if (regs)
+		show_regs(regs);
 
-	ret = notify_die(DIE_OOPS, str, regs, 0, regs->cause, SIGSEGV);
+	cause = regs ? regs->cause : -1;
+	ret = notify_die(DIE_OOPS, str, regs, 0, cause, SIGSEGV);
+
+	if (kexec_should_crash(current))
+		crash_kexec(regs);
 
 	bust_spinlocks(0);
 	add_taint(TAINT_DIE, LOCKDEP_NOW_UNRELIABLE);
-	spin_unlock_irq(&die_lock);
+	raw_spin_unlock_irqrestore(&die_lock, flags);
 	oops_exit();
 
 	if (in_interrupt())
@@ -54,7 +63,7 @@
 	if (panic_on_oops)
 		panic("Fatal exception");
 	if (ret != NOTIFY_STOP)
-		do_exit(SIGSEGV);
+		make_task_dead(SIGSEGV);
 }
 
 void do_trap(struct pt_regs *regs, int signo, int code, unsigned long addr)
@@ -206,18 +215,36 @@
  * shadow stack, handled_ kernel_ stack_ overflow(in kernel/entry.S) is used
  * to get per-cpu overflow stack(get_overflow_stack).
  */
-long shadow_stack[SHADOW_OVERFLOW_STACK_SIZE/sizeof(long)];
+long shadow_stack[SHADOW_OVERFLOW_STACK_SIZE/sizeof(long)] __aligned(16);
 asmlinkage unsigned long get_overflow_stack(void)
 {
 	return (unsigned long)this_cpu_ptr(overflow_stack) +
 		OVERFLOW_STACK_SIZE;
 }
 
+/*
+ * A pseudo spinlock to protect the shadow stack from being used by multiple
+ * harts concurrently.  This isn't a real spinlock because the lock side must
+ * be taken without a valid stack and only a single register, it's only taken
+ * while in the process of panicing anyway so the performance and error
+ * checking a proper spinlock gives us doesn't matter.
+ */
+unsigned long spin_shadow_stack;
+
 asmlinkage void handle_bad_stack(struct pt_regs *regs)
 {
 	unsigned long tsk_stk = (unsigned long)current->stack;
 	unsigned long ovf_stk = (unsigned long)this_cpu_ptr(overflow_stack);
 
+	/*
+	 * We're done with the shadow stack by this point, as we're on the
+	 * overflow stack.  Tell any other concurrent overflowing harts that
+	 * they can proceed with panicing by releasing the pseudo-spinlock.
+	 *
+	 * This pairs with an amoswap.aq in handle_kernel_stack_overflow.
+	 */
+	smp_store_release(&spin_shadow_stack, 0);
+
 	console_verbose();
 
 	pr_emerg("Insufficient stack space to handle exception!\n");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/traps_misaligned.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/traps_misaligned.c
@@ -131,8 +131,6 @@
 #define REG_PTR(insn, pos, regs)	\
 	(ulong *)((ulong)(regs) + REG_OFFSET(insn, pos))
 
-#define GET_RM(insn)			(((insn) >> 12) & 7)
-
 #define GET_RS1(insn, regs)		(*REG_PTR(insn, SH_RS1, regs))
 #define GET_RS2(insn, regs)		(*REG_PTR(insn, SH_RS2, regs))
 #define GET_RS1S(insn, regs)		(*REG_PTR(RVC_RS1S(insn), 0, regs))
@@ -344,16 +342,14 @@
 	} else if ((insn & INSN_MASK_C_SD) == INSN_MATCH_C_SD) {
 		len = 8;
 		val.data_ulong = GET_RS2S(insn, regs);
-	} else if ((insn & INSN_MASK_C_SDSP) == INSN_MATCH_C_SDSP &&
-		   ((insn >> SH_RD) & 0x1f)) {
+	} else if ((insn & INSN_MASK_C_SDSP) == INSN_MATCH_C_SDSP) {
 		len = 8;
 		val.data_ulong = GET_RS2C(insn, regs);
 #endif
 	} else if ((insn & INSN_MASK_C_SW) == INSN_MATCH_C_SW) {
 		len = 4;
 		val.data_ulong = GET_RS2S(insn, regs);
-	} else if ((insn & INSN_MASK_C_SWSP) == INSN_MATCH_C_SWSP &&
-		   ((insn >> SH_RD) & 0x1f)) {
+	} else if ((insn & INSN_MASK_C_SWSP) == INSN_MATCH_C_SWSP) {
 		len = 4;
 		val.data_ulong = GET_RS2C(insn, regs);
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/vdso/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/vdso/Makefile
@@ -17,6 +17,8 @@
 obj-vdso = $(patsubst %, %.o, $(vdso-syms)) note.o
 
 ccflags-y := -fno-stack-protector
+ccflags-y += -DDISABLE_BRANCH_PROFILING
+ccflags-y += -fno-builtin
 
 ifneq ($(c-gettimeofday-y),)
   CFLAGS_vgettimeofday.o += -fPIC -include $(c-gettimeofday-y)
@@ -28,9 +30,12 @@
 
 obj-y += vdso.o
 CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
+ifneq ($(filter vgettimeofday, $(vdso-syms)),)
+CPPFLAGS_vdso.lds += -DHAS_VGETTIMEOFDAY
+endif
 
 # Disable -pg to prevent insert call site
-CFLAGS_REMOVE_vgettimeofday.o = $(CC_FLAGS_FTRACE) -Os
+CFLAGS_REMOVE_vgettimeofday.o = $(CC_FLAGS_FTRACE)
 
 # Disable profiling and instrumentation for VDSO code
 GCOV_PROFILE := n
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/vdso/vdso.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/vdso/vdso.lds.S
@@ -65,9 +65,11 @@
 	LINUX_4.15 {
 	global:
 		__vdso_rt_sigreturn;
+#ifdef HAS_VGETTIMEOFDAY
 		__vdso_gettimeofday;
 		__vdso_clock_gettime;
 		__vdso_clock_getres;
+#endif
 		__vdso_getcpu;
 		__vdso_flush_icache;
 	local: *;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/vmlinux-xip.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/vmlinux-xip.lds.S
@@ -29,10 +29,12 @@
 	HEAD_TEXT_SECTION
 	INIT_TEXT_SECTION(PAGE_SIZE)
 	/* we have to discard exit text and such at runtime, not link time */
+	__exittext_begin = .;
 	.exit.text :
 	{
 		EXIT_TEXT
 	}
+	__exittext_end = .;
 
 	.text : {
 		_text = .;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/kernel/vmlinux.lds.S
@@ -73,10 +73,12 @@
 		__soc_builtin_dtb_table_end = .;
 	}
 	/* we have to discard exit text and such at runtime, not link time */
+	__exittext_begin = .;
 	.exit.text :
 	{
 		EXIT_TEXT
 	}
+	__exittext_end = .;
 
 	__init_text_end = .;
 	. = ALIGN(SECTION_ALIGN);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/lib/memmove.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/lib/memmove.S
@@ -1,64 +1,316 @@
-/* SPDX-License-Identifier: GPL-2.0 */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2022 Michael T. Kloos <michael@michaelkloos.com>
+ */
 
 #include <linux/linkage.h>
 #include <asm/asm.h>
 
-ENTRY(__memmove)
-WEAK(memmove)
-        move    t0, a0
-        move    t1, a1
-
-        beq     a0, a1, exit_memcpy
-        beqz    a2, exit_memcpy
-        srli    t2, a2, 0x2
-
-        slt     t3, a0, a1
-        beqz    t3, do_reverse
-
-        andi    a2, a2, 0x3
-        li      t4, 1
-        beqz    t2, byte_copy
-
-word_copy:
-        lw      t3, 0(a1)
-        addi    t2, t2, -1
-        addi    a1, a1, 4
-        sw      t3, 0(a0)
-        addi    a0, a0, 4
-        bnez    t2, word_copy
-        beqz    a2, exit_memcpy
-        j       byte_copy
-
-do_reverse:
-        add     a0, a0, a2
-        add     a1, a1, a2
-        andi    a2, a2, 0x3
-        li      t4, -1
-        beqz    t2, reverse_byte_copy
-
-reverse_word_copy:
-        addi    a1, a1, -4
-        addi    t2, t2, -1
-        lw      t3, 0(a1)
-        addi    a0, a0, -4
-        sw      t3, 0(a0)
-        bnez    t2, reverse_word_copy
-        beqz    a2, exit_memcpy
-
-reverse_byte_copy:
-        addi    a0, a0, -1
-        addi    a1, a1, -1
-
+SYM_FUNC_START(__memmove)
+SYM_FUNC_START_WEAK(memmove)
+	/*
+	 * Returns
+	 *   a0 - dest
+	 *
+	 * Parameters
+	 *   a0 - Inclusive first byte of dest
+	 *   a1 - Inclusive first byte of src
+	 *   a2 - Length of copy n
+	 *
+	 * Because the return matches the parameter register a0,
+	 * we will not clobber or modify that register.
+	 *
+	 * Note: This currently only works on little-endian.
+	 * To port to big-endian, reverse the direction of shifts
+	 * in the 2 misaligned fixup copy loops.
+	 */
+
+	/* Return if nothing to do */
+	beq a0, a1, return_from_memmove
+	beqz a2, return_from_memmove
+
+	/*
+	 * Register Uses
+	 *      Forward Copy: a1 - Index counter of src
+	 *      Reverse Copy: a4 - Index counter of src
+	 *      Forward Copy: t3 - Index counter of dest
+	 *      Reverse Copy: t4 - Index counter of dest
+	 *   Both Copy Modes: t5 - Inclusive first multibyte/aligned of dest
+	 *   Both Copy Modes: t6 - Non-Inclusive last multibyte/aligned of dest
+	 *   Both Copy Modes: t0 - Link / Temporary for load-store
+	 *   Both Copy Modes: t1 - Temporary for load-store
+	 *   Both Copy Modes: t2 - Temporary for load-store
+	 *   Both Copy Modes: a5 - dest to src alignment offset
+	 *   Both Copy Modes: a6 - Shift ammount
+	 *   Both Copy Modes: a7 - Inverse Shift ammount
+	 *   Both Copy Modes: a2 - Alternate breakpoint for unrolled loops
+	 */
+
+	/*
+	 * Solve for some register values now.
+	 * Byte copy does not need t5 or t6.
+	 */
+	mv   t3, a0
+	add  t4, a0, a2
+	add  a4, a1, a2
+
+	/*
+	 * Byte copy if copying less than (2 * SZREG) bytes. This can
+	 * cause problems with the bulk copy implementation and is
+	 * small enough not to bother.
+	 */
+	andi t0, a2, -(2 * SZREG)
+	beqz t0, byte_copy
+
+	/*
+	 * Now solve for t5 and t6.
+	 */
+	andi t5, t3, -SZREG
+	andi t6, t4, -SZREG
+	/*
+	 * If dest(Register t3) rounded down to the nearest naturally
+	 * aligned SZREG address, does not equal dest, then add SZREG
+	 * to find the low-bound of SZREG alignment in the dest memory
+	 * region.  Note that this could overshoot the dest memory
+	 * region if n is less than SZREG.  This is one reason why
+	 * we always byte copy if n is less than SZREG.
+	 * Otherwise, dest is already naturally aligned to SZREG.
+	 */
+	beq  t5, t3, 1f
+		addi t5, t5, SZREG
+	1:
+
+	/*
+	 * If the dest and src are co-aligned to SZREG, then there is
+	 * no need for the full rigmarole of a full misaligned fixup copy.
+	 * Instead, do a simpler co-aligned copy.
+	 */
+	xor  t0, a0, a1
+	andi t1, t0, (SZREG - 1)
+	beqz t1, coaligned_copy
+	/* Fall through to misaligned fixup copy */
+
+misaligned_fixup_copy:
+	bltu a1, a0, misaligned_fixup_copy_reverse
+
+misaligned_fixup_copy_forward:
+	jal  t0, byte_copy_until_aligned_forward
+
+	andi a5, a1, (SZREG - 1) /* Find the alignment offset of src (a1) */
+	slli a6, a5, 3 /* Multiply by 8 to convert that to bits to shift */
+	sub  a5, a1, t3 /* Find the difference between src and dest */
+	andi a1, a1, -SZREG /* Align the src pointer */
+	addi a2, t6, SZREG /* The other breakpoint for the unrolled loop*/
+
+	/*
+	 * Compute The Inverse Shift
+	 * a7 = XLEN - a6 = XLEN + -a6
+	 * 2s complement negation to find the negative: -a6 = ~a6 + 1
+	 * Add that to XLEN.  XLEN = SZREG * 8.
+	 */
+	not  a7, a6
+	addi a7, a7, (SZREG * 8 + 1)
+
+	/*
+	 * Fix Misalignment Copy Loop - Forward
+	 * load_val0 = load_ptr[0];
+	 * do {
+	 * 	load_val1 = load_ptr[1];
+	 * 	store_ptr += 2;
+	 * 	store_ptr[0 - 2] = (load_val0 >> {a6}) | (load_val1 << {a7});
+	 *
+	 * 	if (store_ptr == {a2})
+	 * 		break;
+	 *
+	 * 	load_val0 = load_ptr[2];
+	 * 	load_ptr += 2;
+	 * 	store_ptr[1 - 2] = (load_val1 >> {a6}) | (load_val0 << {a7});
+	 *
+	 * } while (store_ptr != store_ptr_end);
+	 * store_ptr = store_ptr_end;
+	 */
+
+	REG_L t0, (0 * SZREG)(a1)
+	1:
+	REG_L t1, (1 * SZREG)(a1)
+	addi  t3, t3, (2 * SZREG)
+	srl   t0, t0, a6
+	sll   t2, t1, a7
+	or    t2, t0, t2
+	REG_S t2, ((0 * SZREG) - (2 * SZREG))(t3)
+
+	beq   t3, a2, 2f
+
+	REG_L t0, (2 * SZREG)(a1)
+	addi  a1, a1, (2 * SZREG)
+	srl   t1, t1, a6
+	sll   t2, t0, a7
+	or    t2, t1, t2
+	REG_S t2, ((1 * SZREG) - (2 * SZREG))(t3)
+
+	bne   t3, t6, 1b
+	2:
+	mv    t3, t6 /* Fix the dest pointer in case the loop was broken */
+
+	add  a1, t3, a5 /* Restore the src pointer */
+	j byte_copy_forward /* Copy any remaining bytes */
+
+misaligned_fixup_copy_reverse:
+	jal  t0, byte_copy_until_aligned_reverse
+
+	andi a5, a4, (SZREG - 1) /* Find the alignment offset of src (a4) */
+	slli a6, a5, 3 /* Multiply by 8 to convert that to bits to shift */
+	sub  a5, a4, t4 /* Find the difference between src and dest */
+	andi a4, a4, -SZREG /* Align the src pointer */
+	addi a2, t5, -SZREG /* The other breakpoint for the unrolled loop*/
+
+	/*
+	 * Compute The Inverse Shift
+	 * a7 = XLEN - a6 = XLEN + -a6
+	 * 2s complement negation to find the negative: -a6 = ~a6 + 1
+	 * Add that to XLEN.  XLEN = SZREG * 8.
+	 */
+	not  a7, a6
+	addi a7, a7, (SZREG * 8 + 1)
+
+	/*
+	 * Fix Misalignment Copy Loop - Reverse
+	 * load_val1 = load_ptr[0];
+	 * do {
+	 * 	load_val0 = load_ptr[-1];
+	 * 	store_ptr -= 2;
+	 * 	store_ptr[1] = (load_val0 >> {a6}) | (load_val1 << {a7});
+	 *
+	 * 	if (store_ptr == {a2})
+	 * 		break;
+	 *
+	 * 	load_val1 = load_ptr[-2];
+	 * 	load_ptr -= 2;
+	 * 	store_ptr[0] = (load_val1 >> {a6}) | (load_val0 << {a7});
+	 *
+	 * } while (store_ptr != store_ptr_end);
+	 * store_ptr = store_ptr_end;
+	 */
+
+	REG_L t1, ( 0 * SZREG)(a4)
+	1:
+	REG_L t0, (-1 * SZREG)(a4)
+	addi  t4, t4, (-2 * SZREG)
+	sll   t1, t1, a7
+	srl   t2, t0, a6
+	or    t2, t1, t2
+	REG_S t2, ( 1 * SZREG)(t4)
+
+	beq   t4, a2, 2f
+
+	REG_L t1, (-2 * SZREG)(a4)
+	addi  a4, a4, (-2 * SZREG)
+	sll   t0, t0, a7
+	srl   t2, t1, a6
+	or    t2, t0, t2
+	REG_S t2, ( 0 * SZREG)(t4)
+
+	bne   t4, t5, 1b
+	2:
+	mv    t4, t5 /* Fix the dest pointer in case the loop was broken */
+
+	add  a4, t4, a5 /* Restore the src pointer */
+	j byte_copy_reverse /* Copy any remaining bytes */
+
+/*
+ * Simple copy loops for SZREG co-aligned memory locations.
+ * These also make calls to do byte copies for any unaligned
+ * data at their terminations.
+ */
+coaligned_copy:
+	bltu a1, a0, coaligned_copy_reverse
+
+coaligned_copy_forward:
+	jal t0, byte_copy_until_aligned_forward
+
+	1:
+	REG_L t1, ( 0 * SZREG)(a1)
+	addi  a1, a1, SZREG
+	addi  t3, t3, SZREG
+	REG_S t1, (-1 * SZREG)(t3)
+	bne   t3, t6, 1b
+
+	j byte_copy_forward /* Copy any remaining bytes */
+
+coaligned_copy_reverse:
+	jal t0, byte_copy_until_aligned_reverse
+
+	1:
+	REG_L t1, (-1 * SZREG)(a4)
+	addi  a4, a4, -SZREG
+	addi  t4, t4, -SZREG
+	REG_S t1, ( 0 * SZREG)(t4)
+	bne   t4, t5, 1b
+
+	j byte_copy_reverse /* Copy any remaining bytes */
+
+/*
+ * These are basically sub-functions within the function.  They
+ * are used to byte copy until the dest pointer is in alignment.
+ * At which point, a bulk copy method can be used by the
+ * calling code.  These work on the same registers as the bulk
+ * copy loops.  Therefore, the register values can be picked
+ * up from where they were left and we avoid code duplication
+ * without any overhead except the call in and return jumps.
+ */
+byte_copy_until_aligned_forward:
+	beq  t3, t5, 2f
+	1:
+	lb   t1,  0(a1)
+	addi a1, a1, 1
+	addi t3, t3, 1
+	sb   t1, -1(t3)
+	bne  t3, t5, 1b
+	2:
+	jalr zero, 0x0(t0) /* Return to multibyte copy loop */
+
+byte_copy_until_aligned_reverse:
+	beq  t4, t6, 2f
+	1:
+	lb   t1, -1(a4)
+	addi a4, a4, -1
+	addi t4, t4, -1
+	sb   t1,  0(t4)
+	bne  t4, t6, 1b
+	2:
+	jalr zero, 0x0(t0) /* Return to multibyte copy loop */
+
+/*
+ * Simple byte copy loops.
+ * These will byte copy until they reach the end of data to copy.
+ * At that point, they will call to return from memmove.
+ */
 byte_copy:
-        lb      t3, 0(a1)
-        addi    a2, a2, -1
-        sb      t3, 0(a0)
-        add     a1, a1, t4
-        add     a0, a0, t4
-        bnez    a2, byte_copy
-
-exit_memcpy:
-        move a0, t0
-        move a1, t1
-        ret
-END(__memmove)
+	bltu a1, a0, byte_copy_reverse
+
+byte_copy_forward:
+	beq  t3, t4, 2f
+	1:
+	lb   t1,  0(a1)
+	addi a1, a1, 1
+	addi t3, t3, 1
+	sb   t1, -1(t3)
+	bne  t3, t4, 1b
+	2:
+	ret
+
+byte_copy_reverse:
+	beq  t4, t3, 2f
+	1:
+	lb   t1, -1(a4)
+	addi a4, a4, -1
+	addi t4, t4, -1
+	sb   t1,  0(t4)
+	bne  t4, t3, 1b
+	2:
+
+return_from_memmove:
+	ret
+
+SYM_FUNC_END(memmove)
+SYM_FUNC_END(__memmove)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/lib/uaccess.S
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/lib/uaccess.S
@@ -19,8 +19,11 @@
 	li t6, SR_SUM
 	csrs CSR_STATUS, t6
 
-	/* Save for return value */
-	mv	t5, a2
+	/*
+	 * Save the terminal address which will be used to compute the number
+	 * of bytes copied in case of a fixup exception.
+	 */
+	add	t5, a0, a2
 
 	/*
 	 * Register allocation for code below:
@@ -173,6 +176,13 @@
 	csrc CSR_STATUS, t6
 	li	a0, 0
 	ret
+
+	/* Exception fixup code */
+10:
+	/* Disable access to user memory */
+	csrc CSR_STATUS, t6
+	sub a0, t5, a0
+	ret
 ENDPROC(__asm_copy_to_user)
 ENDPROC(__asm_copy_from_user)
 EXPORT_SYMBOL(__asm_copy_to_user)
@@ -218,19 +228,12 @@
 	addi a0, a0, 1
 	bltu a0, a3, 5b
 	j 3b
-ENDPROC(__clear_user)
-EXPORT_SYMBOL(__clear_user)
 
-	.section .fixup,"ax"
-	.balign 4
-	/* Fixup code for __copy_user(10) and __clear_user(11) */
-10:
-	/* Disable access to user memory */
-	csrs CSR_STATUS, t6
-	mv a0, t5
-	ret
+	/* Exception fixup code */
 11:
-	csrs CSR_STATUS, t6
-	mv a0, a1
+	/* Disable access to user memory */
+	csrc CSR_STATUS, t6
+	sub a0, a3, a0
 	ret
-	.previous
+ENDPROC(__clear_user)
+EXPORT_SYMBOL(__clear_user)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/Makefile
@@ -24,6 +24,9 @@
 ifdef CONFIG_KASAN
 KASAN_SANITIZE_kasan_init.o := n
 KASAN_SANITIZE_init.o := n
+ifdef CONFIG_DEBUG_VIRTUAL
+KASAN_SANITIZE_physaddr.o := n
+endif
 endif
 
 obj-$(CONFIG_DEBUG_VIRTUAL) += physaddr.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/cacheflush.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/cacheflush.c
@@ -85,7 +85,9 @@
 {
 	struct page *page = pte_page(pte);
 
-	if (!test_and_set_bit(PG_dcache_clean, &page->flags))
+	if (!test_bit(PG_dcache_clean, &page->flags)) {
 		flush_icache_all();
+		set_bit(PG_dcache_clean, &page->flags);
+	}
 }
 #endif /* CONFIG_MMU */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/context.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/context.c
@@ -22,7 +22,7 @@
 
 static unsigned long asid_bits;
 static unsigned long num_asids;
-static unsigned long asid_mask;
+unsigned long asid_mask;
 
 static atomic_long_t current_version;
 
@@ -205,12 +205,24 @@
 	local_flush_tlb_all();
 }
 
-static inline void set_mm(struct mm_struct *mm, unsigned int cpu)
+static inline void set_mm(struct mm_struct *prev,
+			  struct mm_struct *next, unsigned int cpu)
 {
-	if (static_branch_unlikely(&use_asid_allocator))
-		set_mm_asid(mm, cpu);
-	else
-		set_mm_noasid(mm);
+	/*
+	 * The mm_cpumask indicates which harts' TLBs contain the virtual
+	 * address mapping of the mm. Compared to noasid, using asid
+	 * can't guarantee that stale TLB entries are invalidated because
+	 * the asid mechanism wouldn't flush TLB for every switch_mm for
+	 * performance. So when using asid, keep all CPUs footmarks in
+	 * cpumask() until mm reset.
+	 */
+	cpumask_set_cpu(cpu, mm_cpumask(next));
+	if (static_branch_unlikely(&use_asid_allocator)) {
+		set_mm_asid(next, cpu);
+	} else {
+		cpumask_clear_cpu(cpu, mm_cpumask(prev));
+		set_mm_noasid(next);
+	}
 }
 
 static int __init asids_init(void)
@@ -262,7 +274,8 @@
 }
 early_initcall(asids_init);
 #else
-static inline void set_mm(struct mm_struct *mm, unsigned int cpu)
+static inline void set_mm(struct mm_struct *prev,
+			  struct mm_struct *next, unsigned int cpu)
 {
 	/* Nothing to do here when there is no MMU */
 }
@@ -315,10 +328,7 @@
 	 */
 	cpu = smp_processor_id();
 
-	cpumask_clear_cpu(cpu, mm_cpumask(prev));
-	cpumask_set_cpu(cpu, mm_cpumask(next));
-
-	set_mm(next, cpu);
+	set_mm(prev, next, cpu);
 
 	flush_icache_deferred(next, cpu);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/fault.c
@@ -31,7 +31,7 @@
 
 	bust_spinlocks(0);
 	die(regs, "Oops");
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 static inline void no_context(struct pt_regs *regs, unsigned long addr)
@@ -60,26 +60,27 @@
 
 static inline void mm_fault_error(struct pt_regs *regs, unsigned long addr, vm_fault_t fault)
 {
+	if (!user_mode(regs)) {
+		no_context(regs, addr);
+		return;
+	}
+
 	if (fault & VM_FAULT_OOM) {
 		/*
 		 * We ran out of memory, call the OOM killer, and return the userspace
 		 * (which will retry the fault, or kill us if we got oom-killed).
 		 */
-		if (!user_mode(regs)) {
-			no_context(regs, addr);
-			return;
-		}
 		pagefault_out_of_memory();
 		return;
 	} else if (fault & VM_FAULT_SIGBUS) {
 		/* Kernel mode? Handle exceptions or die */
-		if (!user_mode(regs)) {
-			no_context(regs, addr);
-			return;
-		}
 		do_trap(regs, SIGBUS, BUS_ADRERR, addr);
 		return;
+	} else if (fault & VM_FAULT_SIGSEGV) {
+		do_trap(regs, SIGSEGV, SEGV_MAPERR, addr);
+		return;
 	}
+
 	BUG();
 }
 
@@ -188,7 +189,8 @@
 		}
 		break;
 	case EXC_LOAD_PAGE_FAULT:
-		if (!(vma->vm_flags & VM_READ)) {
+		/* Write implies read */
+		if (!(vma->vm_flags & (VM_READ | VM_WRITE))) {
 			return true;
 		}
 		break;
@@ -270,10 +272,12 @@
 	if (user_mode(regs))
 		flags |= FAULT_FLAG_USER;
 
-	if (!user_mode(regs) && addr < TASK_SIZE &&
-			unlikely(!(regs->status & SR_SUM)))
-		die_kernel_fault("access to user memory without uaccess routines",
-				addr, regs);
+	if (!user_mode(regs) && addr < TASK_SIZE && unlikely(!(regs->status & SR_SUM))) {
+		if (fixup_exception(regs))
+			return;
+
+		die_kernel_fault("access to user memory without uaccess routines", addr, regs);
+	}
 
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, addr);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/init.c
@@ -49,7 +49,6 @@
 EXPORT_SYMBOL(empty_zero_page);
 
 extern char _start[];
-#define DTB_EARLY_BASE_VA      PGDIR_SIZE
 void *_dtb_early_va __initdata;
 uintptr_t _dtb_early_pa __initdata;
 
@@ -100,12 +99,15 @@
 		  (unsigned long)VMEMMAP_END);
 	print_mlm("vmalloc", (unsigned long)VMALLOC_START,
 		  (unsigned long)VMALLOC_END);
-	print_mlm("lowmem", (unsigned long)PAGE_OFFSET,
-		  (unsigned long)high_memory);
 #ifdef CONFIG_64BIT
-	print_mlm("kernel", (unsigned long)KERNEL_LINK_ADDR,
-		  (unsigned long)ADDRESS_SPACE_END);
+	print_mlm("modules", (unsigned long)MODULES_VADDR,
+		  (unsigned long)MODULES_END);
 #endif
+	print_mlm("lowmem", (unsigned long)PAGE_OFFSET,
+		  (unsigned long)high_memory);
+	if (IS_ENABLED(CONFIG_64BIT))
+		print_mlm("kernel", (unsigned long)KERNEL_LINK_ADDR,
+			  (unsigned long)ADDRESS_SPACE_END);
 }
 #else
 static void print_vm_layout(void) { }
@@ -163,7 +165,7 @@
 {
 	phys_addr_t vmlinux_end = __pa_symbol(&_end);
 	phys_addr_t vmlinux_start = __pa_symbol(&_start);
-	phys_addr_t __maybe_unused max_mapped_addr;
+	phys_addr_t max_mapped_addr;
 	phys_addr_t phys_ram_end;
 
 #ifdef CONFIG_XIP_KERNEL
@@ -173,37 +175,37 @@
 	memblock_enforce_memory_limit(memory_limit);
 
 	/*
-	 * Reserve from the start of the kernel to the end of the kernel
-	 */
-#if defined(CONFIG_64BIT) && defined(CONFIG_STRICT_KERNEL_RWX)
-	/*
 	 * Make sure we align the reservation on PMD_SIZE since we will
 	 * map the kernel in the linear mapping as read-only: we do not want
 	 * any allocation to happen between _end and the next pmd aligned page.
 	 */
-	vmlinux_end = (vmlinux_end + PMD_SIZE - 1) & PMD_MASK;
-#endif
+	if (IS_ENABLED(CONFIG_64BIT) && IS_ENABLED(CONFIG_STRICT_KERNEL_RWX))
+		vmlinux_end = (vmlinux_end + PMD_SIZE - 1) & PMD_MASK;
+	/*
+	 * Reserve from the start of the kernel to the end of the kernel
+	 */
 	memblock_reserve(vmlinux_start, vmlinux_end - vmlinux_start);
 
 
 	phys_ram_end = memblock_end_of_DRAM();
-#ifndef CONFIG_64BIT
 #ifndef CONFIG_XIP_KERNEL
 	phys_ram_base = memblock_start_of_DRAM();
 #endif
 	/*
-	 * memblock allocator is not aware of the fact that last 4K bytes of
-	 * the addressable memory can not be mapped because of IS_ERR_VALUE
-	 * macro. Make sure that last 4k bytes are not usable by memblock
-	 * if end of dram is equal to maximum addressable memory.  For 64-bit
-	 * kernel, this problem can't happen here as the end of the virtual
-	 * address space is occupied by the kernel mapping then this check must
-	 * be done as soon as the kernel mapping base address is determined.
-	 */
-	max_mapped_addr = __pa(~(ulong)0);
-	if (max_mapped_addr == (phys_ram_end - 1))
-		memblock_set_current_limit(max_mapped_addr - 4096);
-#endif
+	 * Reserve physical address space that would be mapped to virtual
+	 * addresses greater than (void *)(-PAGE_SIZE) because:
+	 *  - This memory would overlap with ERR_PTR
+	 *  - This memory belongs to high memory, which is not supported
+	 *
+	 * This is not applicable to 64-bit kernel, because virtual addresses
+	 * after (void *)(-PAGE_SIZE) are not linearly mapped: they are
+	 * occupied by kernel mapping. Also it is unrealistic for high memory
+	 * to exist on 64-bit platforms.
+	 */
+	if (!IS_ENABLED(CONFIG_64BIT)) {
+		max_mapped_addr = __va_to_pa_nodebug(-PAGE_SIZE);
+		memblock_reserve(max_mapped_addr, (phys_addr_t)-max_mapped_addr);
+	}
 
 	min_low_pfn = PFN_UP(phys_ram_base);
 	max_low_pfn = max_pfn = PFN_DOWN(phys_ram_end);
@@ -212,6 +214,14 @@
 	set_max_mapnr(max_low_pfn - ARCH_PFN_OFFSET);
 
 	reserve_initrd_mem();
+
+	/*
+	 * No allocation should be done before reserving the memory as defined
+	 * in the device tree, otherwise the allocation could end up in a
+	 * reserved region.
+	 */
+	early_init_fdt_scan_reserved_mem();
+
 	/*
 	 * If DTB is built in, no need to reserve its memblock.
 	 * Otherwise, do reserve it but avoid using
@@ -221,11 +231,9 @@
 	if (!IS_ENABLED(CONFIG_BUILTIN_DTB))
 		memblock_reserve(dtb_early_pa, fdt_totalsize(dtb_early_va));
 
-	early_init_fdt_scan_reserved_mem();
 	dma_contiguous_reserve(dma32_phys_limit);
 	if (IS_ENABLED(CONFIG_64BIT))
 		hugetlb_cma_reserve(PUD_SHIFT - PAGE_SHIFT);
-	memblock_allow_resize();
 }
 
 #ifdef CONFIG_MMU
@@ -245,9 +253,9 @@
 static pte_t fixmap_pte[PTRS_PER_PTE] __page_aligned_bss;
 
 pgd_t early_pg_dir[PTRS_PER_PGD] __initdata __aligned(PAGE_SIZE);
-static pmd_t __maybe_unused early_dtb_pmd[PTRS_PER_PMD] __initdata __aligned(PAGE_SIZE);
 
 #ifdef CONFIG_XIP_KERNEL
+#define riscv_pfn_base         (*(unsigned long  *)XIP_FIXUP(&riscv_pfn_base))
 #define trampoline_pg_dir      ((pgd_t *)XIP_FIXUP(trampoline_pg_dir))
 #define fixmap_pte             ((pte_t *)XIP_FIXUP(fixmap_pte))
 #define early_pg_dir           ((pgd_t *)XIP_FIXUP(early_pg_dir))
@@ -451,6 +459,7 @@
 }
 
 #ifdef CONFIG_XIP_KERNEL
+#define phys_ram_base  (*(phys_addr_t *)XIP_FIXUP(&phys_ram_base))
 /* called from head.S with MMU off */
 asmlinkage void __init __copy_data(void)
 {
@@ -558,24 +567,27 @@
  * this means 2 PMD entries whereas for 32-bit kernel, this is only 1 PGDIR
  * entry.
  */
-static void __init create_fdt_early_page_table(pgd_t *pgdir, uintptr_t dtb_pa)
+static void __init create_fdt_early_page_table(uintptr_t fix_fdt_va,
+					       uintptr_t dtb_pa)
 {
 #ifndef CONFIG_BUILTIN_DTB
 	uintptr_t pa = dtb_pa & ~(PMD_SIZE - 1);
 
-	create_pgd_mapping(early_pg_dir, DTB_EARLY_BASE_VA,
-			   IS_ENABLED(CONFIG_64BIT) ? (uintptr_t)early_dtb_pmd : pa,
-			   PGDIR_SIZE,
-			   IS_ENABLED(CONFIG_64BIT) ? PAGE_TABLE : PAGE_KERNEL);
+	/* Make sure the fdt fixmap address is always aligned on PMD size */
+	BUILD_BUG_ON(FIX_FDT % (PMD_SIZE / PAGE_SIZE));
 
-	if (IS_ENABLED(CONFIG_64BIT)) {
-		create_pmd_mapping(early_dtb_pmd, DTB_EARLY_BASE_VA,
+	/* In 32-bit only, the fdt lies in its own PGD */
+	if (!IS_ENABLED(CONFIG_64BIT)) {
+		create_pgd_mapping(early_pg_dir, fix_fdt_va,
+				   pa, MAX_FDT_SIZE, PAGE_KERNEL);
+	} else {
+		create_pmd_mapping(fixmap_pmd, fix_fdt_va,
 				   pa, PMD_SIZE, PAGE_KERNEL);
-		create_pmd_mapping(early_dtb_pmd, DTB_EARLY_BASE_VA + PMD_SIZE,
+		create_pmd_mapping(fixmap_pmd, fix_fdt_va + PMD_SIZE,
 				   pa + PMD_SIZE, PMD_SIZE, PAGE_KERNEL);
 	}
 
-	dtb_early_va = (void *)DTB_EARLY_BASE_VA + (dtb_pa & (PMD_SIZE - 1));
+	dtb_early_va = (void *)fix_fdt_va + (dtb_pa & (PMD_SIZE - 1));
 #else
 	/*
 	 * For 64-bit kernel, __va can't be used since it would return a linear
@@ -617,14 +629,6 @@
 	BUG_ON((PAGE_OFFSET % PGDIR_SIZE) != 0);
 	BUG_ON((kernel_map.phys_addr % PMD_SIZE) != 0);
 
-#ifdef CONFIG_64BIT
-	/*
-	 * The last 4K bytes of the addressable memory can not be mapped because
-	 * of IS_ERR_VALUE macro.
-	 */
-	BUG_ON((kernel_map.virt_addr + kernel_map.size) > ADDRESS_SPACE_END - SZ_4K);
-#endif
-
 	pt_ops.alloc_pte = alloc_pte_early;
 	pt_ops.get_pte_virt = get_pte_virt_early;
 #ifndef __PAGETABLE_PMD_FOLDED
@@ -663,7 +667,7 @@
 	create_kernel_page_table(early_pg_dir, true);
 
 	/* Setup early mapping for FDT early scan */
-	create_fdt_early_page_table(early_pg_dir, dtb_pa);
+	create_fdt_early_page_table(__fix_to_virt(FIX_FDT), dtb_pa);
 
 	/*
 	 * Bootime fixmap only can handle PMD_SIZE mapping. Thus, boot-ioremap
@@ -700,6 +704,7 @@
 {
 	uintptr_t va, map_size;
 	phys_addr_t pa, start, end;
+	unsigned long idx __maybe_unused;
 	u64 i;
 
 	/**
@@ -713,6 +718,16 @@
 	pt_ops.get_pmd_virt = get_pmd_virt_fixmap;
 #endif
 	/* Setup swapper PGD for fixmap */
+#if !defined(CONFIG_64BIT)
+	/*
+	 * In 32-bit, the device tree lies in a pgd entry, so it must be copied
+	 * directly in swapper_pg_dir in addition to the pgd entry that points
+	 * to fixmap_pte.
+	 */
+	idx = pgd_index(__fix_to_virt(FIX_FDT));
+
+	set_pgd(&swapper_pg_dir[idx], early_pg_dir[idx]);
+#endif
 	create_pgd_mapping(swapper_pg_dir, FIXADDR_START,
 			   __pa_symbol(fixmap_pgd_next),
 			   PGDIR_SIZE, PAGE_TABLE);
@@ -736,10 +751,9 @@
 		}
 	}
 
-#ifdef CONFIG_64BIT
 	/* Map the kernel */
-	create_kernel_page_table(swapper_pg_dir, false);
-#endif
+	if (IS_ENABLED(CONFIG_64BIT))
+		create_kernel_page_table(swapper_pg_dir, false);
 
 	/* Clear fixmap PTE and PMD mappings */
 	clear_fixmap(FIX_PTE);
@@ -813,13 +827,22 @@
 	/*
 	 * Current riscv boot protocol requires 2MB alignment for
 	 * RV64 and 4MB alignment for RV32 (hugepage size)
+	 *
+	 * Try to alloc from 32bit addressible physical memory so that
+	 * swiotlb can work on the crash kernel.
 	 */
 	crash_base = memblock_phys_alloc_range(crash_size, PMD_SIZE,
-					       search_start, search_end);
+					       search_start,
+					       min(search_end, (unsigned long)(SZ_4G - 1)));
 	if (crash_base == 0) {
-		pr_warn("crashkernel: couldn't allocate %lldKB\n",
-			crash_size >> 10);
-		return;
+		/* Try again without restricting region to 32bit addressible memory */
+		crash_base = memblock_phys_alloc_range(crash_size, PMD_SIZE,
+						search_start, search_end);
+		if (crash_base == 0) {
+			pr_warn("crashkernel: couldn't allocate %lldKB\n",
+				crash_size >> 10);
+			return;
+		}
 	}
 
 	pr_info("crashkernel: reserved 0x%016llx - 0x%016llx (%lld MB)\n",
@@ -834,6 +857,9 @@
 {
 	setup_bootmem();
 	setup_vm_final();
+
+	/* Depend on that Linear Mapping is ready */
+	memblock_allow_resize();
 }
 
 void __init misc_mem_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/kasan_init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/kasan_init.c
@@ -22,8 +22,7 @@
 
 	for (i = 0; i < PTRS_PER_PTE; ++i)
 		set_pte(kasan_early_shadow_pte + i,
-			mk_pte(virt_to_page(kasan_early_shadow_page),
-			       PAGE_KERNEL));
+			pfn_pte(virt_to_pfn(kasan_early_shadow_page), PAGE_KERNEL));
 
 	for (i = 0; i < PTRS_PER_PMD; ++i)
 		set_pmd(kasan_early_shadow_pmd + i,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/pageattr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/pageattr.c
@@ -118,10 +118,10 @@
 	if (!numpages)
 		return 0;
 
-	mmap_read_lock(&init_mm);
+	mmap_write_lock(&init_mm);
 	ret =  walk_page_range_novma(&init_mm, start, end, &pageattr_ops, NULL,
 				     &masks);
-	mmap_read_unlock(&init_mm);
+	mmap_write_unlock(&init_mm);
 
 	flush_tlb_kernel_range(start, end);
 
@@ -191,17 +191,33 @@
 }
 
 #ifdef CONFIG_DEBUG_PAGEALLOC
+static int debug_pagealloc_set_page(pte_t *pte, unsigned long addr, void *data)
+{
+	int enable = *(int *)data;
+
+	unsigned long val = pte_val(ptep_get(pte));
+
+	if (enable)
+		val |= _PAGE_PRESENT;
+	else
+		val &= ~_PAGE_PRESENT;
+
+	set_pte(pte, __pte(val));
+
+	return 0;
+}
+
 void __kernel_map_pages(struct page *page, int numpages, int enable)
 {
 	if (!debug_pagealloc_enabled())
 		return;
 
-	if (enable)
-		__set_memory((unsigned long)page_address(page), numpages,
-			     __pgprot(_PAGE_PRESENT), __pgprot(0));
-	else
-		__set_memory((unsigned long)page_address(page), numpages,
-			     __pgprot(0), __pgprot(_PAGE_PRESENT));
+	unsigned long start = (unsigned long)page_address(page);
+	unsigned long size = PAGE_SIZE * numpages;
+
+	apply_to_existing_page_range(&init_mm, start, size, debug_pagealloc_set_page, &enable);
+
+	flush_tlb_kernel_range(start, start + size);
 }
 #endif
 
@@ -217,18 +233,26 @@
 	pgd = pgd_offset_k(addr);
 	if (!pgd_present(*pgd))
 		return false;
+	if (pgd_leaf(*pgd))
+		return true;
 
 	p4d = p4d_offset(pgd, addr);
 	if (!p4d_present(*p4d))
 		return false;
+	if (p4d_leaf(*p4d))
+		return true;
 
 	pud = pud_offset(p4d, addr);
 	if (!pud_present(*pud))
 		return false;
+	if (pud_leaf(*pud))
+		return true;
 
 	pmd = pmd_offset(pud, addr);
 	if (!pmd_present(*pmd))
 		return false;
+	if (pmd_leaf(*pmd))
+		return true;
 
 	pte = pte_offset_kernel(pmd, addr);
 	return pte_present(*pte);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/mm/tlbflush.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/mm/tlbflush.c
@@ -43,7 +43,7 @@
 	/* check if the tlbflush needs to be sent to other CPUs */
 	broadcast = cpumask_any_but(cmask, cpuid) < nr_cpu_ids;
 	if (static_branch_unlikely(&use_asid_allocator)) {
-		unsigned long asid = atomic_long_read(&mm->context.id);
+		unsigned long asid = atomic_long_read(&mm->context.id) & asid_mask;
 
 		if (broadcast) {
 			riscv_cpuid_to_hartid_mask(cmask, &hmask);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/net/bpf_jit.h
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/net/bpf_jit.h
@@ -69,6 +69,7 @@
 	struct bpf_prog *prog;
 	u16 *insns;		/* RV insns */
 	int ninsns;
+	int prologue_len;
 	int epilogue_offset;
 	int *offset;		/* BPF to RV */
 	unsigned long flags;
@@ -214,8 +215,8 @@
 	int from, to;
 
 	off++; /* BPF branch is from PC+1, RV is from PC */
-	from = (insn > 0) ? ctx->offset[insn - 1] : 0;
-	to = (insn + off > 0) ? ctx->offset[insn + off - 1] : 0;
+	from = (insn > 0) ? ctx->offset[insn - 1] : ctx->prologue_len;
+	to = (insn + off > 0) ? ctx->offset[insn + off - 1] : ctx->prologue_len;
 	return ninsns_rvoff(to - from);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/net/bpf_jit_comp64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/net/bpf_jit_comp64.c
@@ -120,6 +120,25 @@
 		val < ((1L << 31) - (1L << 11));
 }
 
+/* Emit fixed-length instructions for address */
+static int emit_addr(u8 rd, u64 addr, bool extra_pass, struct rv_jit_context *ctx)
+{
+	u64 ip = (u64)(ctx->insns + ctx->ninsns);
+	s64 off = addr - ip;
+	s64 upper = (off + (1 << 11)) >> 12;
+	s64 lower = off & 0xfff;
+
+	if (extra_pass && !in_auipc_jalr_range(off)) {
+		pr_err("bpf-jit: target offset 0x%llx is out of range\n", off);
+		return -ERANGE;
+	}
+
+	emit(rv_auipc(rd, upper), ctx);
+	emit(rv_addi(rd, rd, lower), ctx);
+	return 0;
+}
+
+/* Emit variable-length instructions for 32-bit and 64-bit imm */
 static void emit_imm(u8 rd, s64 val, struct rv_jit_context *ctx)
 {
 	/* Note that the immediate from the add is sign-extended,
@@ -201,7 +220,7 @@
 	emit_addi(RV_REG_SP, RV_REG_SP, stack_adjust, ctx);
 	/* Set return value. */
 	if (!is_tail_call)
-		emit_mv(RV_REG_A0, RV_REG_A5, ctx);
+		emit_addiw(RV_REG_A0, RV_REG_A5, 0, ctx);
 	emit_jalr(RV_REG_ZERO, is_tail_call ? RV_REG_T3 : RV_REG_RA,
 		  is_tail_call ? 4 : 0, /* skip TCC init */
 		  ctx);
@@ -394,12 +413,12 @@
 	*rd = RV_REG_T2;
 }
 
-static int emit_jump_and_link(u8 rd, s64 rvoff, bool force_jalr,
+static int emit_jump_and_link(u8 rd, s64 rvoff, bool fixed_addr,
 			      struct rv_jit_context *ctx)
 {
 	s64 upper, lower;
 
-	if (rvoff && is_21b_int(rvoff) && !force_jalr) {
+	if (rvoff && fixed_addr && is_21b_int(rvoff)) {
 		emit(rv_jal(rd, rvoff >> 1), ctx);
 		return 0;
 	} else if (in_auipc_jalr_range(rvoff)) {
@@ -420,24 +439,17 @@
 		cond == BPF_JSGE || cond == BPF_JSLE;
 }
 
-static int emit_call(bool fixed, u64 addr, struct rv_jit_context *ctx)
+static int emit_call(u64 addr, bool fixed_addr, struct rv_jit_context *ctx)
 {
 	s64 off = 0;
 	u64 ip;
-	u8 rd;
-	int ret;
 
 	if (addr && ctx->insns) {
 		ip = (u64)(long)(ctx->insns + ctx->ninsns);
 		off = addr - ip;
 	}
 
-	ret = emit_jump_and_link(RV_REG_RA, off, !fixed, ctx);
-	if (ret)
-		return ret;
-	rd = bpf_to_rv_reg(BPF_REG_0, ctx);
-	emit_mv(rd, RV_REG_A0, ctx);
-	return 0;
+	return emit_jump_and_link(RV_REG_RA, off, fixed_addr, ctx);
 }
 
 int bpf_jit_emit_insn(const struct bpf_insn *insn, struct rv_jit_context *ctx,
@@ -731,7 +743,7 @@
 	/* JUMP off */
 	case BPF_JMP | BPF_JA:
 		rvoff = rv_offset(i, off, ctx);
-		ret = emit_jump_and_link(RV_REG_ZERO, rvoff, false, ctx);
+		ret = emit_jump_and_link(RV_REG_ZERO, rvoff, true, ctx);
 		if (ret)
 			return ret;
 		break;
@@ -850,17 +862,21 @@
 	/* function call */
 	case BPF_JMP | BPF_CALL:
 	{
-		bool fixed;
+		bool fixed_addr;
 		u64 addr;
 
 		mark_call(ctx);
-		ret = bpf_jit_get_func_addr(ctx->prog, insn, extra_pass, &addr,
-					    &fixed);
+		ret = bpf_jit_get_func_addr(ctx->prog, insn, extra_pass,
+					    &addr, &fixed_addr);
 		if (ret < 0)
 			return ret;
-		ret = emit_call(fixed, addr, ctx);
+
+		ret = emit_call(addr, fixed_addr, ctx);
 		if (ret)
 			return ret;
+
+		if (insn->src_reg != BPF_PSEUDO_CALL)
+			emit_mv(bpf_to_rv_reg(BPF_REG_0, ctx), RV_REG_A0, ctx);
 		break;
 	}
 	/* tail call */
@@ -875,7 +891,7 @@
 			break;
 
 		rvoff = epilogue_offset(ctx);
-		ret = emit_jump_and_link(RV_REG_ZERO, rvoff, false, ctx);
+		ret = emit_jump_and_link(RV_REG_ZERO, rvoff, true, ctx);
 		if (ret)
 			return ret;
 		break;
@@ -887,7 +903,15 @@
 		u64 imm64;
 
 		imm64 = (u64)insn1.imm << 32 | (u32)imm;
-		emit_imm(rd, imm64, ctx);
+		if (bpf_pseudo_func(insn)) {
+			/* fixed-length insns for extra jit pass */
+			ret = emit_addr(rd, imm64, extra_pass, ctx);
+			if (ret)
+				return ret;
+		} else {
+			emit_imm(rd, imm64, ctx);
+		}
+
 		return 1;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/riscv/net/bpf_jit_core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/riscv/net/bpf_jit_core.c
@@ -83,6 +83,12 @@
 		prog = orig_prog;
 		goto out_offset;
 	}
+
+	if (build_body(ctx, extra_pass, NULL)) {
+		prog = orig_prog;
+		goto out_offset;
+	}
+
 	for (i = 0; i < prog->len; i++) {
 		prev_ninsns += 32;
 		ctx->offset[i] = prev_ninsns;
@@ -91,11 +97,15 @@
 	for (i = 0; i < NR_JIT_ITERATIONS; i++) {
 		pass++;
 		ctx->ninsns = 0;
+
+		bpf_jit_build_prologue(ctx);
+		ctx->prologue_len = ctx->ninsns;
+
 		if (build_body(ctx, extra_pass, ctx->offset)) {
 			prog = orig_prog;
 			goto out_offset;
 		}
-		bpf_jit_build_prologue(ctx);
+
 		ctx->epilogue_offset = ctx->ninsns;
 		bpf_jit_build_epilogue(ctx);
 
@@ -154,6 +164,9 @@
 
 	if (!prog->is_func || extra_pass) {
 		bpf_jit_binary_lock_ro(jit_data->header);
+		for (i = 0; i < prog->len; i++)
+			ctx->offset[i] = ninsns_rvoff(ctx->offset[i]);
+		bpf_prog_fill_jited_linfo(prog, ctx->offset);
 out_offset:
 		kfree(ctx->offset);
 		kfree(jit_data);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/Kconfig
@@ -47,7 +47,7 @@
 config KASAN_SHADOW_OFFSET
 	hex
 	depends on KASAN
-	default 0x18000000000000
+	default 0x1C000000000000
 
 config S390
 	def_bool y
@@ -516,7 +516,6 @@
 config KEXEC_FILE
 	bool "kexec file based system call"
 	select KEXEC_CORE
-	select BUILD_BIN2C
 	depends on CRYPTO
 	depends on CRYPTO_SHA256
 	depends on CRYPTO_SHA256_S390
@@ -574,6 +573,7 @@
 
 config EXPOLINE
 	def_bool n
+	depends on $(cc-option,-mindirect-branch=thunk)
 	prompt "Avoid speculative indirect branches in the kernel"
 	help
 	  Compile the kernel with the expoline compiler options to guard
@@ -584,6 +584,20 @@
 
 	  If unsure, say N.
 
+config EXPOLINE_EXTERN
+	def_bool n
+	depends on EXPOLINE
+	depends on HAVE_MARCH_Z10_FEATURES
+	depends on CC_IS_GCC && GCC_VERSION >= 110200
+	depends on $(success,$(srctree)/arch/s390/tools/gcc-thunk-extern.sh $(CC))
+	prompt "Generate expolines as extern functions."
+	help
+	  This option is required for some tooling like kpatch. The kernel is
+	  compiled with -mindirect-branch=thunk-extern and requires a newer
+	  compiler.
+
+	  If unsure, say N.
+
 choice
 	prompt "Expoline default"
 	depends on EXPOLINE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/Makefile
@@ -29,9 +29,20 @@
 KBUILD_CFLAGS_DECOMPRESSOR += -fno-asynchronous-unwind-tables
 KBUILD_CFLAGS_DECOMPRESSOR += -ffreestanding
 KBUILD_CFLAGS_DECOMPRESSOR += -fno-stack-protector
+KBUILD_CFLAGS_DECOMPRESSOR += -fPIE
 KBUILD_CFLAGS_DECOMPRESSOR += $(call cc-disable-warning, address-of-packed-member)
 KBUILD_CFLAGS_DECOMPRESSOR += $(if $(CONFIG_DEBUG_INFO),-g)
 KBUILD_CFLAGS_DECOMPRESSOR += $(if $(CONFIG_DEBUG_INFO_DWARF4), $(call cc-option, -gdwarf-4,))
+
+ifdef CONFIG_CC_IS_GCC
+	ifeq ($(call cc-ifversion, -ge, 1200, y), y)
+		ifeq ($(call cc-ifversion, -lt, 1300, y), y)
+			KBUILD_CFLAGS += $(call cc-disable-warning, array-bounds)
+			KBUILD_CFLAGS_DECOMPRESSOR += $(call cc-disable-warning, array-bounds)
+		endif
+	endif
+endif
+
 UTS_MACHINE	:= s390x
 STACK_SIZE	:= $(if $(CONFIG_KASAN),65536,16384)
 CHECKFLAGS	+= -D__s390__ -D__s390x__
@@ -79,21 +90,27 @@
 KBUILD_CFLAGS_DECOMPRESSOR += $(cflags-y)
 
 ifneq ($(call cc-option,-mstack-size=8192 -mstack-guard=128),)
-cflags-$(CONFIG_CHECK_STACK) += -mstack-size=$(STACK_SIZE)
-ifeq ($(call cc-option,-mstack-size=8192),)
-cflags-$(CONFIG_CHECK_STACK) += -mstack-guard=$(CONFIG_STACK_GUARD)
-endif
+  CC_FLAGS_CHECK_STACK := -mstack-size=$(STACK_SIZE)
+  ifeq ($(call cc-option,-mstack-size=8192),)
+    CC_FLAGS_CHECK_STACK += -mstack-guard=$(CONFIG_STACK_GUARD)
+  endif
+  export CC_FLAGS_CHECK_STACK
+  cflags-$(CONFIG_CHECK_STACK) += $(CC_FLAGS_CHECK_STACK)
 endif
 
 ifdef CONFIG_EXPOLINE
-  ifneq ($(call cc-option,$(CC_FLAGS_MARCH) -mindirect-branch=thunk),)
+  ifdef CONFIG_EXPOLINE_EXTERN
+    KBUILD_LDFLAGS_MODULE += arch/s390/lib/expoline/expoline.o
+    CC_FLAGS_EXPOLINE := -mindirect-branch=thunk-extern
+    CC_FLAGS_EXPOLINE += -mfunction-return=thunk-extern
+  else
     CC_FLAGS_EXPOLINE := -mindirect-branch=thunk
     CC_FLAGS_EXPOLINE += -mfunction-return=thunk
-    CC_FLAGS_EXPOLINE += -mindirect-branch-table
-    export CC_FLAGS_EXPOLINE
-    cflags-y += $(CC_FLAGS_EXPOLINE) -DCC_USING_EXPOLINE
-    aflags-y += -DCC_USING_EXPOLINE
   endif
+  CC_FLAGS_EXPOLINE += -mindirect-branch-table
+  export CC_FLAGS_EXPOLINE
+  cflags-y += $(CC_FLAGS_EXPOLINE) -DCC_USING_EXPOLINE
+  aflags-y += -DCC_USING_EXPOLINE
 endif
 
 ifdef CONFIG_FUNCTION_TRACER
@@ -169,6 +186,12 @@
 	$(Q)$(MAKE) $(build)=arch/s390/kernel/vdso64 include/generated/vdso64-offsets.h
 	$(if $(CONFIG_COMPAT),$(Q)$(MAKE) \
 		$(build)=arch/s390/kernel/vdso32 include/generated/vdso32-offsets.h)
+
+ifdef CONFIG_EXPOLINE_EXTERN
+modules_prepare: expoline_prepare
+expoline_prepare: prepare0
+	$(Q)$(MAKE) $(build)=arch/s390/lib/expoline arch/s390/lib/expoline/expoline.o
+endif
 endif
 
 # Don't use tabs in echo arguments
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/compressed/decompressor.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/compressed/decompressor.c
@@ -80,6 +80,6 @@
 	void *output = (void *)decompress_offset;
 
 	__decompress(_compressed_start, _compressed_end - _compressed_start,
-		     NULL, NULL, output, 0, NULL, error);
+		     NULL, NULL, output, vmlinux.image_size, NULL, error);
 	return output;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/compressed/decompressor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/compressed/decompressor.h
@@ -24,6 +24,7 @@
 	unsigned long dynsym_start;
 	unsigned long rela_dyn_start;
 	unsigned long rela_dyn_end;
+	unsigned long amode31_size;
 };
 
 /* Symbols defined by linker scripts */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/compressed/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/compressed/vmlinux.lds.S
@@ -93,8 +93,17 @@
 		_compressed_start = .;
 		*(.vmlinux.bin.compressed)
 		_compressed_end = .;
-		FILL(0xff);
-		. = ALIGN(4096);
+	}
+
+#define SB_TRAILER_SIZE 32
+	/* Trailer needed for Secure Boot */
+	. += SB_TRAILER_SIZE; /* make sure .sb.trailer does not overwrite the previous section */
+	. = ALIGN(4096) - SB_TRAILER_SIZE;
+	.sb.trailer : {
+		QUAD(0)
+		QUAD(0)
+		QUAD(0)
+		QUAD(0x000000207a49504c)
 	}
 	_end = .;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/head.S
@@ -184,35 +184,23 @@
 	bas	%r14,.Lloader		# load parameter file
 	ltr	%r2,%r2 		# got anything ?
 	bz	.Lnopf
-	chi	%r2,895
-	bnh	.Lnotrunc
-	la	%r2,895
+	l	%r3,MAX_COMMAND_LINE_SIZE+ARCH_OFFSET-PARMAREA(%r12)
+	ahi	%r3,-1
+	clr	%r2,%r3
+	bl	.Lnotrunc
+	lr	%r2,%r3
 .Lnotrunc:
 	l	%r4,.Linitrd
 	clc	0(3,%r4),.L_hdr		# if it is HDRx
 	bz	.Lagain1		# skip dataset header
 	clc	0(3,%r4),.L_eof		# if it is EOFx
 	bz	.Lagain1		# skip dateset trailer
-	la	%r5,0(%r4,%r2)
-	lr	%r3,%r2
-	la	%r3,COMMAND_LINE-PARMAREA(%r12) # load adr. of command line
-	mvc	0(256,%r3),0(%r4)
-	mvc	256(256,%r3),256(%r4)
-	mvc	512(256,%r3),512(%r4)
-	mvc	768(122,%r3),768(%r4)
-	slr	%r0,%r0
-	b	.Lcntlp
-.Ldelspc:
-	ic	%r0,0(%r2,%r3)
-	chi	%r0,0x20		# is it a space ?
-	be	.Lcntlp
-	ahi	%r2,1
-	b	.Leolp
-.Lcntlp:
-	brct	%r2,.Ldelspc
-.Leolp:
-	slr	%r0,%r0
-	stc	%r0,0(%r2,%r3)		# terminate buffer
+
+	lr	%r5,%r2
+	la	%r6,COMMAND_LINE-PARMAREA(%r12)
+	lr	%r7,%r2
+	ahi	%r7,1
+	mvcl	%r6,%r4
 .Lnopf:
 
 #
@@ -377,11 +365,10 @@
 	.quad	0			# OLDMEM_BASE
 	.quad	0			# OLDMEM_SIZE
 	.quad	kernel_version		# points to kernel version string
+	.quad	COMMAND_LINE_SIZE
 
 	.org	COMMAND_LINE
 	.byte	"root=/dev/ram0 ro"
 	.byte	0
 	.org	PARMAREA+__PARMAREA_SIZE
 SYM_DATA_END(parmarea)
-
-	.org	HEAD_END
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/ipl_parm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/ipl_parm.c
@@ -170,10 +170,10 @@
 
 void setup_boot_command_line(void)
 {
-	parmarea.command_line[ARCH_COMMAND_LINE_SIZE - 1] = 0;
+	parmarea.command_line[COMMAND_LINE_SIZE - 1] = 0;
 	/* convert arch command line to ascii if necessary */
 	if (has_ebcdic_char(parmarea.command_line))
-		EBCASC(parmarea.command_line, ARCH_COMMAND_LINE_SIZE);
+		EBCASC(parmarea.command_line, COMMAND_LINE_SIZE);
 	/* copy arch command line */
 	strcpy(early_command_line, strim(parmarea.command_line));
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/ipl_report.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/ipl_report.c
@@ -57,11 +57,19 @@
 	if (IS_ENABLED(CONFIG_BLK_DEV_INITRD) && initrd_data.start && initrd_data.size &&
 	    intersects(initrd_data.start, initrd_data.size, safe_addr, size))
 		safe_addr = initrd_data.start + initrd_data.size;
+	if (intersects(safe_addr, size, (unsigned long)comps, comps->len)) {
+		safe_addr = (unsigned long)comps + comps->len;
+		goto repeat;
+	}
 	for_each_rb_entry(comp, comps)
 		if (intersects(safe_addr, size, comp->addr, comp->len)) {
 			safe_addr = comp->addr + comp->len;
 			goto repeat;
 		}
+	if (intersects(safe_addr, size, (unsigned long)certs, certs->len)) {
+		safe_addr = (unsigned long)certs + certs->len;
+		goto repeat;
+	}
 	for_each_rb_entry(cert, certs)
 		if (intersects(safe_addr, size, cert->addr, cert->len)) {
 			safe_addr = cert->addr + cert->len;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/mem_detect.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/mem_detect.c
@@ -165,7 +165,7 @@
 
 unsigned long detect_memory(void)
 {
-	unsigned long max_physmem_end;
+	unsigned long max_physmem_end = 0;
 
 	sclp_early_get_memsize(&max_physmem_end);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/startup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/startup.c
@@ -15,6 +15,7 @@
 #include "uv.h"
 
 unsigned long __bootdata_preserved(__kaslr_offset);
+unsigned long __bootdata(__amode31_base);
 unsigned long __bootdata_preserved(VMALLOC_START);
 unsigned long __bootdata_preserved(VMALLOC_END);
 struct page *__bootdata_preserved(vmemmap);
@@ -26,7 +27,6 @@
 struct initrd_data __bootdata(initrd_data);
 
 u64 __bootdata_preserved(stfle_fac_list[16]);
-u64 __bootdata_preserved(alt_stfle_fac_list[16]);
 struct oldmem_data __bootdata_preserved(oldmem_data);
 
 void error(char *x)
@@ -148,82 +148,56 @@
 
 static void setup_kernel_memory_layout(void)
 {
-	bool vmalloc_size_verified = false;
-	unsigned long vmemmap_off;
-	unsigned long vspace_left;
+	unsigned long vmemmap_start;
 	unsigned long rte_size;
 	unsigned long pages;
-	unsigned long vmax;
 
 	pages = ident_map_size / PAGE_SIZE;
 	/* vmemmap contains a multiple of PAGES_PER_SECTION struct pages */
 	vmemmap_size = SECTION_ALIGN_UP(pages) * sizeof(struct page);
 
 	/* choose kernel address space layout: 4 or 3 levels. */
-	vmemmap_off = round_up(ident_map_size, _REGION3_SIZE);
+	vmemmap_start = round_up(ident_map_size, _REGION3_SIZE);
 	if (IS_ENABLED(CONFIG_KASAN) ||
 	    vmalloc_size > _REGION2_SIZE ||
-	    vmemmap_off + vmemmap_size + vmalloc_size + MODULES_LEN > _REGION2_SIZE)
-		vmax = _REGION1_SIZE;
-	else
-		vmax = _REGION2_SIZE;
-
-	/* keep vmemmap_off aligned to a top level region table entry */
-	rte_size = vmax == _REGION1_SIZE ? _REGION2_SIZE : _REGION3_SIZE;
-	MODULES_END = vmax;
-	if (is_prot_virt_host()) {
-		/*
-		 * forcing modules and vmalloc area under the ultravisor
-		 * secure storage limit, so that any vmalloc allocation
-		 * we do could be used to back secure guest storage.
-		 */
-		adjust_to_uv_max(&MODULES_END);
-	}
-
-#ifdef CONFIG_KASAN
-	if (MODULES_END < vmax) {
-		/* force vmalloc and modules below kasan shadow */
-		MODULES_END = min(MODULES_END, KASAN_SHADOW_START);
+	    vmemmap_start + vmemmap_size + vmalloc_size + MODULES_LEN >
+		    _REGION2_SIZE) {
+		MODULES_END = _REGION1_SIZE;
+		rte_size = _REGION2_SIZE;
 	} else {
-		/*
-		 * leave vmalloc and modules above kasan shadow but make
-		 * sure they don't overlap with it
-		 */
-		vmalloc_size = min(vmalloc_size, vmax - KASAN_SHADOW_END - MODULES_LEN);
-		vmalloc_size_verified = true;
-		vspace_left = KASAN_SHADOW_START;
+		MODULES_END = _REGION2_SIZE;
+		rte_size = _REGION3_SIZE;
 	}
+	/*
+	 * forcing modules and vmalloc area under the ultravisor
+	 * secure storage limit, so that any vmalloc allocation
+	 * we do could be used to back secure guest storage.
+	 */
+	adjust_to_uv_max(&MODULES_END);
+#ifdef CONFIG_KASAN
+	/* force vmalloc and modules below kasan shadow */
+	MODULES_END = min(MODULES_END, KASAN_SHADOW_START);
 #endif
 	MODULES_VADDR = MODULES_END - MODULES_LEN;
 	VMALLOC_END = MODULES_VADDR;
 
-	if (vmalloc_size_verified) {
-		VMALLOC_START = VMALLOC_END - vmalloc_size;
-	} else {
-		vmemmap_off = round_up(ident_map_size, rte_size);
+	/* allow vmalloc area to occupy up to about 1/2 of the rest virtual space left */
+	vmalloc_size = min(vmalloc_size, round_down(VMALLOC_END / 2, _REGION3_SIZE));
+	VMALLOC_START = VMALLOC_END - vmalloc_size;
 
-		if (vmemmap_off + vmemmap_size > VMALLOC_END ||
-		    vmalloc_size > VMALLOC_END - vmemmap_off - vmemmap_size) {
-			/*
-			 * allow vmalloc area to occupy up to 1/2 of
-			 * the rest virtual space left.
-			 */
-			vmalloc_size = min(vmalloc_size, VMALLOC_END / 2);
-		}
-		VMALLOC_START = VMALLOC_END - vmalloc_size;
-		vspace_left = VMALLOC_START;
-	}
-
-	pages = vspace_left / (PAGE_SIZE + sizeof(struct page));
+	/* split remaining virtual space between 1:1 mapping & vmemmap array */
+	pages = VMALLOC_START / (PAGE_SIZE + sizeof(struct page));
 	pages = SECTION_ALIGN_UP(pages);
-	vmemmap_off = round_up(vspace_left - pages * sizeof(struct page), rte_size);
-	/* keep vmemmap left most starting from a fresh region table entry */
-	vmemmap_off = min(vmemmap_off, round_up(ident_map_size, rte_size));
-	/* take care that identity map is lower then vmemmap */
-	ident_map_size = min(ident_map_size, vmemmap_off);
+	/* keep vmemmap_start aligned to a top level region table entry */
+	vmemmap_start = round_down(VMALLOC_START - pages * sizeof(struct page), rte_size);
+	/* vmemmap_start is the future VMEM_MAX_PHYS, make sure it is within MAX_PHYSMEM */
+	vmemmap_start = min(vmemmap_start, 1UL << MAX_PHYSMEM_BITS);
+	/* make sure identity map doesn't overlay with vmemmap */
+	ident_map_size = min(ident_map_size, vmemmap_start);
 	vmemmap_size = SECTION_ALIGN_UP(ident_map_size / PAGE_SIZE) * sizeof(struct page);
-	VMALLOC_START = max(vmemmap_off + vmemmap_size, VMALLOC_START);
-	vmemmap = (struct page *)vmemmap_off;
+	/* make sure vmemmap doesn't overlay with vmalloc area */
+	VMALLOC_START = max(vmemmap_start + vmemmap_size, VMALLOC_START);
+	vmemmap = (struct page *)vmemmap_start;
 }
 
 /*
@@ -259,6 +233,12 @@
 	vmlinux.dynsym_start += offset;
 }
 
+static unsigned long reserve_amode31(unsigned long safe_addr)
+{
+	__amode31_base = PAGE_ALIGN(safe_addr);
+	return safe_addr + vmlinux.amode31_size;
+}
+
 void startup_kernel(void)
 {
 	unsigned long random_lma;
@@ -273,6 +253,7 @@
 	setup_lpp();
 	store_ipl_parmblock();
 	safe_addr = mem_safe_offset();
+	safe_addr = reserve_amode31(safe_addr);
 	safe_addr = read_ipl_report(safe_addr);
 	uv_query_info();
 	rescue_initrd(safe_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/boot/uv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/boot/uv.c
@@ -41,6 +41,10 @@
 		uv_info.max_num_sec_conf = uvcb.max_num_sec_conf;
 		uv_info.max_guest_cpu_id = uvcb.max_guest_cpu_id;
 		uv_info.uv_feature_indications = uvcb.uv_feature_indications;
+		uv_info.supp_se_hdr_ver = uvcb.supp_se_hdr_versions;
+		uv_info.supp_se_hdr_pcf = uvcb.supp_se_hdr_pcf;
+		uv_info.conf_dump_storage_state_len = uvcb.conf_dump_storage_state_len;
+		uv_info.conf_dump_finalize_len = uvcb.conf_dump_finalize_len;
 	}
 
 #ifdef CONFIG_PROTECTED_VIRTUALIZATION_GUEST
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/configs/debug_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/configs/debug_defconfig
@@ -765,6 +765,7 @@
 CONFIG_CRYPTO_SHA3_512_S390=m
 CONFIG_CRYPTO_DES_S390=m
 CONFIG_CRYPTO_AES_S390=m
+CONFIG_CRYPTO_CHACHA_S390=m
 CONFIG_CRYPTO_GHASH_S390=m
 CONFIG_CRYPTO_CRC32_S390=y
 CONFIG_CRYPTO_DEV_VIRTIO=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/configs/defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/configs/defconfig
@@ -753,6 +753,7 @@
 CONFIG_CRYPTO_SHA3_512_S390=m
 CONFIG_CRYPTO_DES_S390=m
 CONFIG_CRYPTO_AES_S390=m
+CONFIG_CRYPTO_CHACHA_S390=m
 CONFIG_CRYPTO_GHASH_S390=m
 CONFIG_CRYPTO_CRC32_S390=y
 CONFIG_CRYPTO_DEV_VIRTIO=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/Makefile
@@ -11,9 +11,11 @@
 obj-$(CONFIG_CRYPTO_DES_S390) += des_s390.o
 obj-$(CONFIG_CRYPTO_AES_S390) += aes_s390.o
 obj-$(CONFIG_CRYPTO_PAES_S390) += paes_s390.o
+obj-$(CONFIG_CRYPTO_CHACHA_S390) += chacha_s390.o
 obj-$(CONFIG_S390_PRNG) += prng.o
 obj-$(CONFIG_CRYPTO_GHASH_S390) += ghash_s390.o
 obj-$(CONFIG_CRYPTO_CRC32_S390) += crc32-vx_s390.o
 obj-$(CONFIG_ARCH_RANDOM) += arch_random.o
 
 crc32-vx_s390-y := crc32-vx.o crc32le-vx.o crc32be-vx.o
+chacha_s390-y := chacha-glue.o chacha-s390.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/aes_s390.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/aes_s390.c
@@ -601,7 +601,9 @@
 	 * final block may be < AES_BLOCK_SIZE, copy only nbytes
 	 */
 	if (nbytes) {
-		cpacf_kmctr(sctx->fc, sctx->key, buf, walk.src.virt.addr,
+		memset(buf, 0, AES_BLOCK_SIZE);
+		memcpy(buf, walk.src.virt.addr, nbytes);
+		cpacf_kmctr(sctx->fc, sctx->key, buf, buf,
 			    AES_BLOCK_SIZE, walk.iv);
 		memcpy(walk.dst.virt.addr, buf, nbytes);
 		crypto_inc(walk.iv, AES_BLOCK_SIZE);
@@ -701,7 +703,7 @@
 					     unsigned int nbytes)
 {
 	gw->walk_bytes_remain -= nbytes;
-	scatterwalk_unmap(&gw->walk);
+	scatterwalk_unmap(gw->walk_ptr);
 	scatterwalk_advance(&gw->walk, nbytes);
 	scatterwalk_done(&gw->walk, 0, gw->walk_bytes_remain);
 	gw->walk_ptr = NULL;
@@ -776,7 +778,7 @@
 		goto out;
 	}
 
-	scatterwalk_unmap(&gw->walk);
+	scatterwalk_unmap(gw->walk_ptr);
 	gw->walk_ptr = NULL;
 
 	gw->ptr = gw->buf;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/arch_random.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/arch_random.c
@@ -4,232 +4,15 @@
  *
  * Copyright IBM Corp. 2017, 2020
  * Author(s): Harald Freudenberger
- *
- * The s390_arch_random_generate() function may be called from random.c
- * in interrupt context. So this implementation does the best to be very
- * fast. There is a buffer of random data which is asynchronously checked
- * and filled by a workqueue thread.
- * If there are enough bytes in the buffer the s390_arch_random_generate()
- * just delivers these bytes. Otherwise false is returned until the
- * worker thread refills the buffer.
- * The worker fills the rng buffer by pulling fresh entropy from the
- * high quality (but slow) true hardware random generator. This entropy
- * is then spread over the buffer with an pseudo random generator PRNG.
- * As the arch_get_random_seed_long() fetches 8 bytes and the calling
- * function add_interrupt_randomness() counts this as 1 bit entropy the
- * distribution needs to make sure there is in fact 1 bit entropy contained
- * in 8 bytes of the buffer. The current values pull 32 byte entropy
- * and scatter this into a 2048 byte buffer. So 8 byte in the buffer
- * will contain 1 bit of entropy.
- * The worker thread is rescheduled based on the charge level of the
- * buffer but at least with 500 ms delay to avoid too much CPU consumption.
- * So the max. amount of rng data delivered via arch_get_random_seed is
- * limited to 4k bytes per second.
  */
 
 #include <linux/kernel.h>
 #include <linux/atomic.h>
 #include <linux/random.h>
-#include <linux/slab.h>
 #include <linux/static_key.h>
-#include <linux/workqueue.h>
-#include <linux/moduleparam.h>
 #include <asm/cpacf.h>
 
 DEFINE_STATIC_KEY_FALSE(s390_arch_random_available);
 
 atomic64_t s390_arch_random_counter = ATOMIC64_INIT(0);
 EXPORT_SYMBOL(s390_arch_random_counter);
-
-#define ARCH_REFILL_TICKS (HZ/2)
-#define ARCH_PRNG_SEED_SIZE 32
-#define ARCH_RNG_BUF_SIZE 2048
-
-static DEFINE_SPINLOCK(arch_rng_lock);
-static u8 *arch_rng_buf;
-static unsigned int arch_rng_buf_idx;
-
-static void arch_rng_refill_buffer(struct work_struct *);
-static DECLARE_DELAYED_WORK(arch_rng_work, arch_rng_refill_buffer);
-
-bool s390_arch_random_generate(u8 *buf, unsigned int nbytes)
-{
-	/* max hunk is ARCH_RNG_BUF_SIZE */
-	if (nbytes > ARCH_RNG_BUF_SIZE)
-		return false;
-
-	/* lock rng buffer */
-	if (!spin_trylock(&arch_rng_lock))
-		return false;
-
-	/* try to resolve the requested amount of bytes from the buffer */
-	arch_rng_buf_idx -= nbytes;
-	if (arch_rng_buf_idx < ARCH_RNG_BUF_SIZE) {
-		memcpy(buf, arch_rng_buf + arch_rng_buf_idx, nbytes);
-		atomic64_add(nbytes, &s390_arch_random_counter);
-		spin_unlock(&arch_rng_lock);
-		return true;
-	}
-
-	/* not enough bytes in rng buffer, refill is done asynchronously */
-	spin_unlock(&arch_rng_lock);
-
-	return false;
-}
-EXPORT_SYMBOL(s390_arch_random_generate);
-
-static void arch_rng_refill_buffer(struct work_struct *unused)
-{
-	unsigned int delay = ARCH_REFILL_TICKS;
-
-	spin_lock(&arch_rng_lock);
-	if (arch_rng_buf_idx > ARCH_RNG_BUF_SIZE) {
-		/* buffer is exhausted and needs refill */
-		u8 seed[ARCH_PRNG_SEED_SIZE];
-		u8 prng_wa[240];
-		/* fetch ARCH_PRNG_SEED_SIZE bytes of entropy */
-		cpacf_trng(NULL, 0, seed, sizeof(seed));
-		/* blow this entropy up to ARCH_RNG_BUF_SIZE with PRNG */
-		memset(prng_wa, 0, sizeof(prng_wa));
-		cpacf_prno(CPACF_PRNO_SHA512_DRNG_SEED,
-			   &prng_wa, NULL, 0, seed, sizeof(seed));
-		cpacf_prno(CPACF_PRNO_SHA512_DRNG_GEN,
-			   &prng_wa, arch_rng_buf, ARCH_RNG_BUF_SIZE, NULL, 0);
-		arch_rng_buf_idx = ARCH_RNG_BUF_SIZE;
-	}
-	delay += (ARCH_REFILL_TICKS * arch_rng_buf_idx) / ARCH_RNG_BUF_SIZE;
-	spin_unlock(&arch_rng_lock);
-
-	/* kick next check */
-	queue_delayed_work(system_long_wq, &arch_rng_work, delay);
-}
-
-/*
- * Here follows the implementation of s390_arch_get_random_long().
- *
- * The random longs to be pulled by arch_get_random_long() are
- * prepared in an 4K buffer which is filled from the NIST 800-90
- * compliant s390 drbg. By default the random long buffer is refilled
- * 256 times before the drbg itself needs a reseed. The reseed of the
- * drbg is done with 32 bytes fetched from the high quality (but slow)
- * trng which is assumed to deliver 100% entropy. So the 32 * 8 = 256
- * bits of entropy are spread over 256 * 4KB = 1MB serving 131072
- * arch_get_random_long() invocations before reseeded.
- *
- * How often the 4K random long buffer is refilled with the drbg
- * before the drbg is reseeded can be adjusted. There is a module
- * parameter 's390_arch_rnd_long_drbg_reseed' accessible via
- *   /sys/module/arch_random/parameters/rndlong_drbg_reseed
- * or as kernel command line parameter
- *   arch_random.rndlong_drbg_reseed=<value>
- * This parameter tells how often the drbg fills the 4K buffer before
- * it is re-seeded by fresh entropy from the trng.
- * A value of 16 results in reseeding the drbg at every 16 * 4 KB = 64
- * KB with 32 bytes of fresh entropy pulled from the trng. So a value
- * of 16 would result in 256 bits entropy per 64 KB.
- * A value of 256 results in 1MB of drbg output before a reseed of the
- * drbg is done. So this would spread the 256 bits of entropy among 1MB.
- * Setting this parameter to 0 forces the reseed to take place every
- * time the 4K buffer is depleted, so the entropy rises to 256 bits
- * entropy per 4K or 0.5 bit entropy per arch_get_random_long().  With
- * setting this parameter to negative values all this effort is
- * disabled, arch_get_random long() returns false and thus indicating
- * that the arch_get_random_long() feature is disabled at all.
- */
-
-static unsigned long rndlong_buf[512];
-static DEFINE_SPINLOCK(rndlong_lock);
-static int rndlong_buf_index;
-
-static int rndlong_drbg_reseed = 256;
-module_param_named(rndlong_drbg_reseed, rndlong_drbg_reseed, int, 0600);
-MODULE_PARM_DESC(rndlong_drbg_reseed, "s390 arch_get_random_long() drbg reseed");
-
-static inline void refill_rndlong_buf(void)
-{
-	static u8 prng_ws[240];
-	static int drbg_counter;
-
-	if (--drbg_counter < 0) {
-		/* need to re-seed the drbg */
-		u8 seed[32];
-
-		/* fetch seed from trng */
-		cpacf_trng(NULL, 0, seed, sizeof(seed));
-		/* seed drbg */
-		memset(prng_ws, 0, sizeof(prng_ws));
-		cpacf_prno(CPACF_PRNO_SHA512_DRNG_SEED,
-			   &prng_ws, NULL, 0, seed, sizeof(seed));
-		/* re-init counter for drbg */
-		drbg_counter = rndlong_drbg_reseed;
-	}
-
-	/* fill the arch_get_random_long buffer from drbg */
-	cpacf_prno(CPACF_PRNO_SHA512_DRNG_GEN, &prng_ws,
-		   (u8 *) rndlong_buf, sizeof(rndlong_buf),
-		   NULL, 0);
-}
-
-bool s390_arch_get_random_long(unsigned long *v)
-{
-	bool rc = false;
-	unsigned long flags;
-
-	/* arch_get_random_long() disabled ? */
-	if (rndlong_drbg_reseed < 0)
-		return false;
-
-	/* try to lock the random long lock */
-	if (!spin_trylock_irqsave(&rndlong_lock, flags))
-		return false;
-
-	if (--rndlong_buf_index >= 0) {
-		/* deliver next long value from the buffer */
-		*v = rndlong_buf[rndlong_buf_index];
-		rc = true;
-		goto out;
-	}
-
-	/* buffer is depleted and needs refill */
-	if (in_interrupt()) {
-		/* delay refill in interrupt context to next caller */
-		rndlong_buf_index = 0;
-		goto out;
-	}
-
-	/* refill random long buffer */
-	refill_rndlong_buf();
-	rndlong_buf_index = ARRAY_SIZE(rndlong_buf);
-
-	/* and provide one random long */
-	*v = rndlong_buf[--rndlong_buf_index];
-	rc = true;
-
-out:
-	spin_unlock_irqrestore(&rndlong_lock, flags);
-	return rc;
-}
-EXPORT_SYMBOL(s390_arch_get_random_long);
-
-static int __init s390_arch_random_init(void)
-{
-	/* all the needed PRNO subfunctions available ? */
-	if (cpacf_query_func(CPACF_PRNO, CPACF_PRNO_TRNG) &&
-	    cpacf_query_func(CPACF_PRNO, CPACF_PRNO_SHA512_DRNG_GEN)) {
-
-		/* alloc arch random working buffer */
-		arch_rng_buf = kmalloc(ARCH_RNG_BUF_SIZE, GFP_KERNEL);
-		if (!arch_rng_buf)
-			return -ENOMEM;
-
-		/* kick worker queue job to fill the random buffer */
-		queue_delayed_work(system_long_wq,
-				   &arch_rng_work, ARCH_REFILL_TICKS);
-
-		/* enable arch random to the outside world */
-		static_branch_enable(&s390_arch_random_available);
-	}
-
-	return 0;
-}
-arch_initcall(s390_arch_random_init);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/chacha-glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/chacha-glue.c
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * s390 ChaCha stream cipher.
+ *
+ * Copyright IBM Corp. 2021
+ */
+
+#define KMSG_COMPONENT "chacha_s390"
+#define pr_fmt(fmt) KMSG_COMPONENT ": " fmt
+
+#include <crypto/internal/chacha.h>
+#include <crypto/internal/skcipher.h>
+#include <crypto/algapi.h>
+#include <linux/cpufeature.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/sizes.h>
+#include <asm/fpu/api.h>
+#include "chacha-s390.h"
+
+static void chacha20_crypt_s390(u32 *state, u8 *dst, const u8 *src,
+				unsigned int nbytes, const u32 *key,
+				u32 *counter)
+{
+	struct kernel_fpu vxstate;
+
+	kernel_fpu_begin(&vxstate, KERNEL_VXR);
+	chacha20_vx(dst, src, nbytes, key, counter);
+	kernel_fpu_end(&vxstate, KERNEL_VXR);
+
+	*counter += round_up(nbytes, CHACHA_BLOCK_SIZE) / CHACHA_BLOCK_SIZE;
+}
+
+static int chacha20_s390(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct chacha_ctx *ctx = crypto_skcipher_ctx(tfm);
+	u32 state[CHACHA_STATE_WORDS] __aligned(16);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int rc;
+
+	rc = skcipher_walk_virt(&walk, req, false);
+	chacha_init_generic(state, ctx->key, req->iv);
+
+	while (walk.nbytes > 0) {
+		nbytes = walk.nbytes;
+		if (nbytes < walk.total)
+			nbytes = round_down(nbytes, walk.stride);
+
+		if (nbytes <= CHACHA_BLOCK_SIZE) {
+			chacha_crypt_generic(state, walk.dst.virt.addr,
+					     walk.src.virt.addr, nbytes,
+					     ctx->nrounds);
+		} else {
+			chacha20_crypt_s390(state, walk.dst.virt.addr,
+					    walk.src.virt.addr, nbytes,
+					    &state[4], &state[12]);
+		}
+		rc = skcipher_walk_done(&walk, walk.nbytes - nbytes);
+	}
+	return rc;
+}
+
+static struct skcipher_alg chacha_algs[] = {
+	{
+		.base.cra_name		= "chacha20",
+		.base.cra_driver_name	= "chacha20-s390",
+		.base.cra_priority	= 900,
+		.base.cra_blocksize	= 1,
+		.base.cra_ctxsize	= sizeof(struct chacha_ctx),
+		.base.cra_module	= THIS_MODULE,
+
+		.min_keysize		= CHACHA_KEY_SIZE,
+		.max_keysize		= CHACHA_KEY_SIZE,
+		.ivsize			= CHACHA_IV_SIZE,
+		.chunksize		= CHACHA_BLOCK_SIZE,
+		.setkey			= chacha20_setkey,
+		.encrypt		= chacha20_s390,
+		.decrypt		= chacha20_s390,
+	}
+};
+
+static int __init chacha_mod_init(void)
+{
+	return crypto_register_skciphers(chacha_algs, ARRAY_SIZE(chacha_algs));
+}
+
+static void __exit chacha_mod_fini(void)
+{
+	crypto_unregister_skciphers(chacha_algs, ARRAY_SIZE(chacha_algs));
+}
+
+module_cpu_feature_match(VXRS, chacha_mod_init);
+module_exit(chacha_mod_fini);
+
+MODULE_DESCRIPTION("ChaCha20 stream cipher");
+MODULE_LICENSE("GPL v2");
+
+MODULE_ALIAS_CRYPTO("chacha20");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/chacha-s390.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/chacha-s390.S
@@ -0,0 +1,907 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Original implementation written by Andy Polyakov, @dot-asm.
+ * This is an adaptation of the original code for kernel use.
+ *
+ * Copyright (C) 2006-2019 CRYPTOGAMS by <appro@openssl.org>. All Rights Reserved.
+ */
+
+#include <linux/linkage.h>
+#include <asm/nospec-insn.h>
+#include <asm/vx-insn.h>
+
+#define SP	%r15
+#define FRAME	(16 * 8 + 4 * 8)
+
+.data
+.align	32
+
+.Lsigma:
+.long	0x61707865,0x3320646e,0x79622d32,0x6b206574	# endian-neutral
+.long	1,0,0,0
+.long	2,0,0,0
+.long	3,0,0,0
+.long	0x03020100,0x07060504,0x0b0a0908,0x0f0e0d0c	# byte swap
+
+.long	0,1,2,3
+.long	0x61707865,0x61707865,0x61707865,0x61707865	# smashed sigma
+.long	0x3320646e,0x3320646e,0x3320646e,0x3320646e
+.long	0x79622d32,0x79622d32,0x79622d32,0x79622d32
+.long	0x6b206574,0x6b206574,0x6b206574,0x6b206574
+
+.previous
+
+	GEN_BR_THUNK %r14
+
+.text
+
+#############################################################################
+# void chacha20_vx_4x(u8 *out, counst u8 *inp, size_t len,
+#		      counst u32 *key, const u32 *counter)
+
+#define	OUT		%r2
+#define	INP		%r3
+#define	LEN		%r4
+#define	KEY		%r5
+#define	COUNTER		%r6
+
+#define BEPERM		%v31
+#define CTR		%v26
+
+#define K0		%v16
+#define K1		%v17
+#define K2		%v18
+#define K3		%v19
+
+#define XA0		%v0
+#define XA1		%v1
+#define XA2		%v2
+#define XA3		%v3
+
+#define XB0		%v4
+#define XB1		%v5
+#define XB2		%v6
+#define XB3		%v7
+
+#define XC0		%v8
+#define XC1		%v9
+#define XC2		%v10
+#define XC3		%v11
+
+#define XD0		%v12
+#define XD1		%v13
+#define XD2		%v14
+#define XD3		%v15
+
+#define XT0		%v27
+#define XT1		%v28
+#define XT2		%v29
+#define XT3		%v30
+
+ENTRY(chacha20_vx_4x)
+	stmg	%r6,%r7,6*8(SP)
+
+	larl	%r7,.Lsigma
+	lhi	%r0,10
+	lhi	%r1,0
+
+	VL	K0,0,,%r7		# load sigma
+	VL	K1,0,,KEY		# load key
+	VL	K2,16,,KEY
+	VL	K3,0,,COUNTER		# load counter
+
+	VL	BEPERM,0x40,,%r7
+	VL	CTR,0x50,,%r7
+
+	VLM	XA0,XA3,0x60,%r7,4	# load [smashed] sigma
+
+	VREPF	XB0,K1,0		# smash the key
+	VREPF	XB1,K1,1
+	VREPF	XB2,K1,2
+	VREPF	XB3,K1,3
+
+	VREPF	XD0,K3,0
+	VREPF	XD1,K3,1
+	VREPF	XD2,K3,2
+	VREPF	XD3,K3,3
+	VAF	XD0,XD0,CTR
+
+	VREPF	XC0,K2,0
+	VREPF	XC1,K2,1
+	VREPF	XC2,K2,2
+	VREPF	XC3,K2,3
+
+.Loop_4x:
+	VAF	XA0,XA0,XB0
+	VX	XD0,XD0,XA0
+	VERLLF	XD0,XD0,16
+
+	VAF	XA1,XA1,XB1
+	VX	XD1,XD1,XA1
+	VERLLF	XD1,XD1,16
+
+	VAF	XA2,XA2,XB2
+	VX	XD2,XD2,XA2
+	VERLLF	XD2,XD2,16
+
+	VAF	XA3,XA3,XB3
+	VX	XD3,XD3,XA3
+	VERLLF	XD3,XD3,16
+
+	VAF	XC0,XC0,XD0
+	VX	XB0,XB0,XC0
+	VERLLF	XB0,XB0,12
+
+	VAF	XC1,XC1,XD1
+	VX	XB1,XB1,XC1
+	VERLLF	XB1,XB1,12
+
+	VAF	XC2,XC2,XD2
+	VX	XB2,XB2,XC2
+	VERLLF	XB2,XB2,12
+
+	VAF	XC3,XC3,XD3
+	VX	XB3,XB3,XC3
+	VERLLF	XB3,XB3,12
+
+	VAF	XA0,XA0,XB0
+	VX	XD0,XD0,XA0
+	VERLLF	XD0,XD0,8
+
+	VAF	XA1,XA1,XB1
+	VX	XD1,XD1,XA1
+	VERLLF	XD1,XD1,8
+
+	VAF	XA2,XA2,XB2
+	VX	XD2,XD2,XA2
+	VERLLF	XD2,XD2,8
+
+	VAF	XA3,XA3,XB3
+	VX	XD3,XD3,XA3
+	VERLLF	XD3,XD3,8
+
+	VAF	XC0,XC0,XD0
+	VX	XB0,XB0,XC0
+	VERLLF	XB0,XB0,7
+
+	VAF	XC1,XC1,XD1
+	VX	XB1,XB1,XC1
+	VERLLF	XB1,XB1,7
+
+	VAF	XC2,XC2,XD2
+	VX	XB2,XB2,XC2
+	VERLLF	XB2,XB2,7
+
+	VAF	XC3,XC3,XD3
+	VX	XB3,XB3,XC3
+	VERLLF	XB3,XB3,7
+
+	VAF	XA0,XA0,XB1
+	VX	XD3,XD3,XA0
+	VERLLF	XD3,XD3,16
+
+	VAF	XA1,XA1,XB2
+	VX	XD0,XD0,XA1
+	VERLLF	XD0,XD0,16
+
+	VAF	XA2,XA2,XB3
+	VX	XD1,XD1,XA2
+	VERLLF	XD1,XD1,16
+
+	VAF	XA3,XA3,XB0
+	VX	XD2,XD2,XA3
+	VERLLF	XD2,XD2,16
+
+	VAF	XC2,XC2,XD3
+	VX	XB1,XB1,XC2
+	VERLLF	XB1,XB1,12
+
+	VAF	XC3,XC3,XD0
+	VX	XB2,XB2,XC3
+	VERLLF	XB2,XB2,12
+
+	VAF	XC0,XC0,XD1
+	VX	XB3,XB3,XC0
+	VERLLF	XB3,XB3,12
+
+	VAF	XC1,XC1,XD2
+	VX	XB0,XB0,XC1
+	VERLLF	XB0,XB0,12
+
+	VAF	XA0,XA0,XB1
+	VX	XD3,XD3,XA0
+	VERLLF	XD3,XD3,8
+
+	VAF	XA1,XA1,XB2
+	VX	XD0,XD0,XA1
+	VERLLF	XD0,XD0,8
+
+	VAF	XA2,XA2,XB3
+	VX	XD1,XD1,XA2
+	VERLLF	XD1,XD1,8
+
+	VAF	XA3,XA3,XB0
+	VX	XD2,XD2,XA3
+	VERLLF	XD2,XD2,8
+
+	VAF	XC2,XC2,XD3
+	VX	XB1,XB1,XC2
+	VERLLF	XB1,XB1,7
+
+	VAF	XC3,XC3,XD0
+	VX	XB2,XB2,XC3
+	VERLLF	XB2,XB2,7
+
+	VAF	XC0,XC0,XD1
+	VX	XB3,XB3,XC0
+	VERLLF	XB3,XB3,7
+
+	VAF	XC1,XC1,XD2
+	VX	XB0,XB0,XC1
+	VERLLF	XB0,XB0,7
+	brct	%r0,.Loop_4x
+
+	VAF	XD0,XD0,CTR
+
+	VMRHF	XT0,XA0,XA1		# transpose data
+	VMRHF	XT1,XA2,XA3
+	VMRLF	XT2,XA0,XA1
+	VMRLF	XT3,XA2,XA3
+	VPDI	XA0,XT0,XT1,0b0000
+	VPDI	XA1,XT0,XT1,0b0101
+	VPDI	XA2,XT2,XT3,0b0000
+	VPDI	XA3,XT2,XT3,0b0101
+
+	VMRHF	XT0,XB0,XB1
+	VMRHF	XT1,XB2,XB3
+	VMRLF	XT2,XB0,XB1
+	VMRLF	XT3,XB2,XB3
+	VPDI	XB0,XT0,XT1,0b0000
+	VPDI	XB1,XT0,XT1,0b0101
+	VPDI	XB2,XT2,XT3,0b0000
+	VPDI	XB3,XT2,XT3,0b0101
+
+	VMRHF	XT0,XC0,XC1
+	VMRHF	XT1,XC2,XC3
+	VMRLF	XT2,XC0,XC1
+	VMRLF	XT3,XC2,XC3
+	VPDI	XC0,XT0,XT1,0b0000
+	VPDI	XC1,XT0,XT1,0b0101
+	VPDI	XC2,XT2,XT3,0b0000
+	VPDI	XC3,XT2,XT3,0b0101
+
+	VMRHF	XT0,XD0,XD1
+	VMRHF	XT1,XD2,XD3
+	VMRLF	XT2,XD0,XD1
+	VMRLF	XT3,XD2,XD3
+	VPDI	XD0,XT0,XT1,0b0000
+	VPDI	XD1,XT0,XT1,0b0101
+	VPDI	XD2,XT2,XT3,0b0000
+	VPDI	XD3,XT2,XT3,0b0101
+
+	VAF	XA0,XA0,K0
+	VAF	XB0,XB0,K1
+	VAF	XC0,XC0,K2
+	VAF	XD0,XD0,K3
+
+	VPERM	XA0,XA0,XA0,BEPERM
+	VPERM	XB0,XB0,XB0,BEPERM
+	VPERM	XC0,XC0,XC0,BEPERM
+	VPERM	XD0,XD0,XD0,BEPERM
+
+	VLM	XT0,XT3,0,INP,0
+
+	VX	XT0,XT0,XA0
+	VX	XT1,XT1,XB0
+	VX	XT2,XT2,XC0
+	VX	XT3,XT3,XD0
+
+	VSTM	XT0,XT3,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+
+	VAF	XA0,XA1,K0
+	VAF	XB0,XB1,K1
+	VAF	XC0,XC1,K2
+	VAF	XD0,XD1,K3
+
+	VPERM	XA0,XA0,XA0,BEPERM
+	VPERM	XB0,XB0,XB0,BEPERM
+	VPERM	XC0,XC0,XC0,BEPERM
+	VPERM	XD0,XD0,XD0,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_4x
+
+	VLM	XT0,XT3,0,INP,0
+
+	VX	XT0,XT0,XA0
+	VX	XT1,XT1,XB0
+	VX	XT2,XT2,XC0
+	VX	XT3,XT3,XD0
+
+	VSTM	XT0,XT3,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_4x
+
+	VAF	XA0,XA2,K0
+	VAF	XB0,XB2,K1
+	VAF	XC0,XC2,K2
+	VAF	XD0,XD2,K3
+
+	VPERM	XA0,XA0,XA0,BEPERM
+	VPERM	XB0,XB0,XB0,BEPERM
+	VPERM	XC0,XC0,XC0,BEPERM
+	VPERM	XD0,XD0,XD0,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_4x
+
+	VLM	XT0,XT3,0,INP,0
+
+	VX	XT0,XT0,XA0
+	VX	XT1,XT1,XB0
+	VX	XT2,XT2,XC0
+	VX	XT3,XT3,XD0
+
+	VSTM	XT0,XT3,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_4x
+
+	VAF	XA0,XA3,K0
+	VAF	XB0,XB3,K1
+	VAF	XC0,XC3,K2
+	VAF	XD0,XD3,K3
+
+	VPERM	XA0,XA0,XA0,BEPERM
+	VPERM	XB0,XB0,XB0,BEPERM
+	VPERM	XC0,XC0,XC0,BEPERM
+	VPERM	XD0,XD0,XD0,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_4x
+
+	VLM	XT0,XT3,0,INP,0
+
+	VX	XT0,XT0,XA0
+	VX	XT1,XT1,XB0
+	VX	XT2,XT2,XC0
+	VX	XT3,XT3,XD0
+
+	VSTM	XT0,XT3,0,OUT,0
+
+.Ldone_4x:
+	lmg	%r6,%r7,6*8(SP)
+	BR_EX	%r14
+
+.Ltail_4x:
+	VLR	XT0,XC0
+	VLR	XT1,XD0
+
+	VST	XA0,8*8+0x00,,SP
+	VST	XB0,8*8+0x10,,SP
+	VST	XT0,8*8+0x20,,SP
+	VST	XT1,8*8+0x30,,SP
+
+	lghi	%r1,0
+
+.Loop_tail_4x:
+	llgc	%r5,0(%r1,INP)
+	llgc	%r6,8*8(%r1,SP)
+	xr	%r6,%r5
+	stc	%r6,0(%r1,OUT)
+	la	%r1,1(%r1)
+	brct	LEN,.Loop_tail_4x
+
+	lmg	%r6,%r7,6*8(SP)
+	BR_EX	%r14
+ENDPROC(chacha20_vx_4x)
+
+#undef	OUT
+#undef	INP
+#undef	LEN
+#undef	KEY
+#undef	COUNTER
+
+#undef BEPERM
+
+#undef K0
+#undef K1
+#undef K2
+#undef K3
+
+
+#############################################################################
+# void chacha20_vx(u8 *out, counst u8 *inp, size_t len,
+#		   counst u32 *key, const u32 *counter)
+
+#define	OUT		%r2
+#define	INP		%r3
+#define	LEN		%r4
+#define	KEY		%r5
+#define	COUNTER		%r6
+
+#define BEPERM		%v31
+
+#define K0		%v27
+#define K1		%v24
+#define K2		%v25
+#define K3		%v26
+
+#define A0		%v0
+#define B0		%v1
+#define C0		%v2
+#define D0		%v3
+
+#define A1		%v4
+#define B1		%v5
+#define C1		%v6
+#define D1		%v7
+
+#define A2		%v8
+#define B2		%v9
+#define C2		%v10
+#define D2		%v11
+
+#define A3		%v12
+#define B3		%v13
+#define C3		%v14
+#define D3		%v15
+
+#define A4		%v16
+#define B4		%v17
+#define C4		%v18
+#define D4		%v19
+
+#define A5		%v20
+#define B5		%v21
+#define C5		%v22
+#define D5		%v23
+
+#define T0		%v27
+#define T1		%v28
+#define T2		%v29
+#define T3		%v30
+
+ENTRY(chacha20_vx)
+	.insn	rilu,0xc20e00000000,LEN,256	# clgfi LEN,256
+	jle	chacha20_vx_4x
+	stmg	%r6,%r7,6*8(SP)
+
+	lghi	%r1,-FRAME
+	lgr	%r0,SP
+	la	SP,0(%r1,SP)
+	stg	%r0,0(SP)		# back-chain
+
+	larl	%r7,.Lsigma
+	lhi	%r0,10
+
+	VLM	K1,K2,0,KEY,0		# load key
+	VL	K3,0,,COUNTER		# load counter
+
+	VLM	K0,BEPERM,0,%r7,4	# load sigma, increments, ...
+
+.Loop_outer_vx:
+	VLR	A0,K0
+	VLR	B0,K1
+	VLR	A1,K0
+	VLR	B1,K1
+	VLR	A2,K0
+	VLR	B2,K1
+	VLR	A3,K0
+	VLR	B3,K1
+	VLR	A4,K0
+	VLR	B4,K1
+	VLR	A5,K0
+	VLR	B5,K1
+
+	VLR	D0,K3
+	VAF	D1,K3,T1		# K[3]+1
+	VAF	D2,K3,T2		# K[3]+2
+	VAF	D3,K3,T3		# K[3]+3
+	VAF	D4,D2,T2		# K[3]+4
+	VAF	D5,D2,T3		# K[3]+5
+
+	VLR	C0,K2
+	VLR	C1,K2
+	VLR	C2,K2
+	VLR	C3,K2
+	VLR	C4,K2
+	VLR	C5,K2
+
+	VLR	T1,D1
+	VLR	T2,D2
+	VLR	T3,D3
+
+.Loop_vx:
+	VAF	A0,A0,B0
+	VAF	A1,A1,B1
+	VAF	A2,A2,B2
+	VAF	A3,A3,B3
+	VAF	A4,A4,B4
+	VAF	A5,A5,B5
+	VX	D0,D0,A0
+	VX	D1,D1,A1
+	VX	D2,D2,A2
+	VX	D3,D3,A3
+	VX	D4,D4,A4
+	VX	D5,D5,A5
+	VERLLF	D0,D0,16
+	VERLLF	D1,D1,16
+	VERLLF	D2,D2,16
+	VERLLF	D3,D3,16
+	VERLLF	D4,D4,16
+	VERLLF	D5,D5,16
+
+	VAF	C0,C0,D0
+	VAF	C1,C1,D1
+	VAF	C2,C2,D2
+	VAF	C3,C3,D3
+	VAF	C4,C4,D4
+	VAF	C5,C5,D5
+	VX	B0,B0,C0
+	VX	B1,B1,C1
+	VX	B2,B2,C2
+	VX	B3,B3,C3
+	VX	B4,B4,C4
+	VX	B5,B5,C5
+	VERLLF	B0,B0,12
+	VERLLF	B1,B1,12
+	VERLLF	B2,B2,12
+	VERLLF	B3,B3,12
+	VERLLF	B4,B4,12
+	VERLLF	B5,B5,12
+
+	VAF	A0,A0,B0
+	VAF	A1,A1,B1
+	VAF	A2,A2,B2
+	VAF	A3,A3,B3
+	VAF	A4,A4,B4
+	VAF	A5,A5,B5
+	VX	D0,D0,A0
+	VX	D1,D1,A1
+	VX	D2,D2,A2
+	VX	D3,D3,A3
+	VX	D4,D4,A4
+	VX	D5,D5,A5
+	VERLLF	D0,D0,8
+	VERLLF	D1,D1,8
+	VERLLF	D2,D2,8
+	VERLLF	D3,D3,8
+	VERLLF	D4,D4,8
+	VERLLF	D5,D5,8
+
+	VAF	C0,C0,D0
+	VAF	C1,C1,D1
+	VAF	C2,C2,D2
+	VAF	C3,C3,D3
+	VAF	C4,C4,D4
+	VAF	C5,C5,D5
+	VX	B0,B0,C0
+	VX	B1,B1,C1
+	VX	B2,B2,C2
+	VX	B3,B3,C3
+	VX	B4,B4,C4
+	VX	B5,B5,C5
+	VERLLF	B0,B0,7
+	VERLLF	B1,B1,7
+	VERLLF	B2,B2,7
+	VERLLF	B3,B3,7
+	VERLLF	B4,B4,7
+	VERLLF	B5,B5,7
+
+	VSLDB	C0,C0,C0,8
+	VSLDB	C1,C1,C1,8
+	VSLDB	C2,C2,C2,8
+	VSLDB	C3,C3,C3,8
+	VSLDB	C4,C4,C4,8
+	VSLDB	C5,C5,C5,8
+	VSLDB	B0,B0,B0,4
+	VSLDB	B1,B1,B1,4
+	VSLDB	B2,B2,B2,4
+	VSLDB	B3,B3,B3,4
+	VSLDB	B4,B4,B4,4
+	VSLDB	B5,B5,B5,4
+	VSLDB	D0,D0,D0,12
+	VSLDB	D1,D1,D1,12
+	VSLDB	D2,D2,D2,12
+	VSLDB	D3,D3,D3,12
+	VSLDB	D4,D4,D4,12
+	VSLDB	D5,D5,D5,12
+
+	VAF	A0,A0,B0
+	VAF	A1,A1,B1
+	VAF	A2,A2,B2
+	VAF	A3,A3,B3
+	VAF	A4,A4,B4
+	VAF	A5,A5,B5
+	VX	D0,D0,A0
+	VX	D1,D1,A1
+	VX	D2,D2,A2
+	VX	D3,D3,A3
+	VX	D4,D4,A4
+	VX	D5,D5,A5
+	VERLLF	D0,D0,16
+	VERLLF	D1,D1,16
+	VERLLF	D2,D2,16
+	VERLLF	D3,D3,16
+	VERLLF	D4,D4,16
+	VERLLF	D5,D5,16
+
+	VAF	C0,C0,D0
+	VAF	C1,C1,D1
+	VAF	C2,C2,D2
+	VAF	C3,C3,D3
+	VAF	C4,C4,D4
+	VAF	C5,C5,D5
+	VX	B0,B0,C0
+	VX	B1,B1,C1
+	VX	B2,B2,C2
+	VX	B3,B3,C3
+	VX	B4,B4,C4
+	VX	B5,B5,C5
+	VERLLF	B0,B0,12
+	VERLLF	B1,B1,12
+	VERLLF	B2,B2,12
+	VERLLF	B3,B3,12
+	VERLLF	B4,B4,12
+	VERLLF	B5,B5,12
+
+	VAF	A0,A0,B0
+	VAF	A1,A1,B1
+	VAF	A2,A2,B2
+	VAF	A3,A3,B3
+	VAF	A4,A4,B4
+	VAF	A5,A5,B5
+	VX	D0,D0,A0
+	VX	D1,D1,A1
+	VX	D2,D2,A2
+	VX	D3,D3,A3
+	VX	D4,D4,A4
+	VX	D5,D5,A5
+	VERLLF	D0,D0,8
+	VERLLF	D1,D1,8
+	VERLLF	D2,D2,8
+	VERLLF	D3,D3,8
+	VERLLF	D4,D4,8
+	VERLLF	D5,D5,8
+
+	VAF	C0,C0,D0
+	VAF	C1,C1,D1
+	VAF	C2,C2,D2
+	VAF	C3,C3,D3
+	VAF	C4,C4,D4
+	VAF	C5,C5,D5
+	VX	B0,B0,C0
+	VX	B1,B1,C1
+	VX	B2,B2,C2
+	VX	B3,B3,C3
+	VX	B4,B4,C4
+	VX	B5,B5,C5
+	VERLLF	B0,B0,7
+	VERLLF	B1,B1,7
+	VERLLF	B2,B2,7
+	VERLLF	B3,B3,7
+	VERLLF	B4,B4,7
+	VERLLF	B5,B5,7
+
+	VSLDB	C0,C0,C0,8
+	VSLDB	C1,C1,C1,8
+	VSLDB	C2,C2,C2,8
+	VSLDB	C3,C3,C3,8
+	VSLDB	C4,C4,C4,8
+	VSLDB	C5,C5,C5,8
+	VSLDB	B0,B0,B0,12
+	VSLDB	B1,B1,B1,12
+	VSLDB	B2,B2,B2,12
+	VSLDB	B3,B3,B3,12
+	VSLDB	B4,B4,B4,12
+	VSLDB	B5,B5,B5,12
+	VSLDB	D0,D0,D0,4
+	VSLDB	D1,D1,D1,4
+	VSLDB	D2,D2,D2,4
+	VSLDB	D3,D3,D3,4
+	VSLDB	D4,D4,D4,4
+	VSLDB	D5,D5,D5,4
+	brct	%r0,.Loop_vx
+
+	VAF	A0,A0,K0
+	VAF	B0,B0,K1
+	VAF	C0,C0,K2
+	VAF	D0,D0,K3
+	VAF	A1,A1,K0
+	VAF	D1,D1,T1		# +K[3]+1
+
+	VPERM	A0,A0,A0,BEPERM
+	VPERM	B0,B0,B0,BEPERM
+	VPERM	C0,C0,C0,BEPERM
+	VPERM	D0,D0,D0,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_vx
+
+	VAF	D2,D2,T2		# +K[3]+2
+	VAF	D3,D3,T3		# +K[3]+3
+	VLM	T0,T3,0,INP,0
+
+	VX	A0,A0,T0
+	VX	B0,B0,T1
+	VX	C0,C0,T2
+	VX	D0,D0,T3
+
+	VLM	K0,T3,0,%r7,4		# re-load sigma and increments
+
+	VSTM	A0,D0,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_vx
+
+	VAF	B1,B1,K1
+	VAF	C1,C1,K2
+
+	VPERM	A0,A1,A1,BEPERM
+	VPERM	B0,B1,B1,BEPERM
+	VPERM	C0,C1,C1,BEPERM
+	VPERM	D0,D1,D1,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_vx
+
+	VLM	A1,D1,0,INP,0
+
+	VX	A0,A0,A1
+	VX	B0,B0,B1
+	VX	C0,C0,C1
+	VX	D0,D0,D1
+
+	VSTM	A0,D0,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_vx
+
+	VAF	A2,A2,K0
+	VAF	B2,B2,K1
+	VAF	C2,C2,K2
+
+	VPERM	A0,A2,A2,BEPERM
+	VPERM	B0,B2,B2,BEPERM
+	VPERM	C0,C2,C2,BEPERM
+	VPERM	D0,D2,D2,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_vx
+
+	VLM	A1,D1,0,INP,0
+
+	VX	A0,A0,A1
+	VX	B0,B0,B1
+	VX	C0,C0,C1
+	VX	D0,D0,D1
+
+	VSTM	A0,D0,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_vx
+
+	VAF	A3,A3,K0
+	VAF	B3,B3,K1
+	VAF	C3,C3,K2
+	VAF	D2,K3,T3		# K[3]+3
+
+	VPERM	A0,A3,A3,BEPERM
+	VPERM	B0,B3,B3,BEPERM
+	VPERM	C0,C3,C3,BEPERM
+	VPERM	D0,D3,D3,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_vx
+
+	VAF	D3,D2,T1		# K[3]+4
+	VLM	A1,D1,0,INP,0
+
+	VX	A0,A0,A1
+	VX	B0,B0,B1
+	VX	C0,C0,C1
+	VX	D0,D0,D1
+
+	VSTM	A0,D0,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_vx
+
+	VAF	A4,A4,K0
+	VAF	B4,B4,K1
+	VAF	C4,C4,K2
+	VAF	D4,D4,D3		# +K[3]+4
+	VAF	D3,D3,T1		# K[3]+5
+	VAF	K3,D2,T3		# K[3]+=6
+
+	VPERM	A0,A4,A4,BEPERM
+	VPERM	B0,B4,B4,BEPERM
+	VPERM	C0,C4,C4,BEPERM
+	VPERM	D0,D4,D4,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_vx
+
+	VLM	A1,D1,0,INP,0
+
+	VX	A0,A0,A1
+	VX	B0,B0,B1
+	VX	C0,C0,C1
+	VX	D0,D0,D1
+
+	VSTM	A0,D0,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	aghi	LEN,-0x40
+	je	.Ldone_vx
+
+	VAF	A5,A5,K0
+	VAF	B5,B5,K1
+	VAF	C5,C5,K2
+	VAF	D5,D5,D3		# +K[3]+5
+
+	VPERM	A0,A5,A5,BEPERM
+	VPERM	B0,B5,B5,BEPERM
+	VPERM	C0,C5,C5,BEPERM
+	VPERM	D0,D5,D5,BEPERM
+
+	.insn	rilu,0xc20e00000000,LEN,0x40	# clgfi LEN,0x40
+	jl	.Ltail_vx
+
+	VLM	A1,D1,0,INP,0
+
+	VX	A0,A0,A1
+	VX	B0,B0,B1
+	VX	C0,C0,C1
+	VX	D0,D0,D1
+
+	VSTM	A0,D0,0,OUT,0
+
+	la	INP,0x40(INP)
+	la	OUT,0x40(OUT)
+	lhi	%r0,10
+	aghi	LEN,-0x40
+	jne	.Loop_outer_vx
+
+.Ldone_vx:
+	lmg	%r6,%r7,FRAME+6*8(SP)
+	la	SP,FRAME(SP)
+	BR_EX	%r14
+
+.Ltail_vx:
+	VSTM	A0,D0,8*8,SP,3
+	lghi	%r1,0
+
+.Loop_tail_vx:
+	llgc	%r5,0(%r1,INP)
+	llgc	%r6,8*8(%r1,SP)
+	xr	%r6,%r5
+	stc	%r6,0(%r1,OUT)
+	la	%r1,1(%r1)
+	brct	LEN,.Loop_tail_vx
+
+	lmg	%r6,%r7,FRAME+6*8(SP)
+	la	SP,FRAME(SP)
+	BR_EX	%r14
+ENDPROC(chacha20_vx)
+
+.previous
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/chacha-s390.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/chacha-s390.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * s390 ChaCha stream cipher.
+ *
+ * Copyright IBM Corp. 2021
+ */
+
+#ifndef _CHACHA_S390_H
+#define _CHACHA_S390_H
+
+void chacha20_vx(u8 *out, const u8 *inp, size_t len, const u32 *key,
+		 const u32 *counter);
+
+#endif /* _CHACHA_S390_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/crypto/paes_s390.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/crypto/paes_s390.c
@@ -35,7 +35,7 @@
  * and padding is also possible, the limits need to be generous.
  */
 #define PAES_MIN_KEYSIZE 16
-#define PAES_MAX_KEYSIZE 320
+#define PAES_MAX_KEYSIZE MAXEP11AESKEYBLOBSIZE
 
 static u8 *ctrblk;
 static DEFINE_MUTEX(ctrblk_lock);
@@ -688,9 +688,11 @@
 	 * final block may be < AES_BLOCK_SIZE, copy only nbytes
 	 */
 	if (nbytes) {
+		memset(buf, 0, AES_BLOCK_SIZE);
+		memcpy(buf, walk.src.virt.addr, nbytes);
 		while (1) {
 			if (cpacf_kmctr(ctx->fc, &param, buf,
-					walk.src.virt.addr, AES_BLOCK_SIZE,
+					buf, AES_BLOCK_SIZE,
 					walk.iv) == AES_BLOCK_SIZE)
 				break;
 			if (__paes_convert_key(ctx))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/hypfs/hypfs_diag.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/hypfs/hypfs_diag.c
@@ -437,7 +437,7 @@
 	int rc;
 
 	if (diag204_probe()) {
-		pr_err("The hardware system does not support hypfs\n");
+		pr_info("The hardware system does not support hypfs\n");
 		return -ENODATA;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/hypfs/hypfs_vm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/hypfs/hypfs_vm.c
@@ -20,6 +20,7 @@
 
 static char local_guest[] = "        ";
 static char all_guests[] = "*       ";
+static char *all_groups = all_guests;
 static char *guest_query;
 
 struct diag2fc_data {
@@ -62,10 +63,11 @@
 
 	memcpy(parm_list.userid, query, NAME_LEN);
 	ASCEBC(parm_list.userid, NAME_LEN);
-	parm_list.addr = (unsigned long) addr ;
+	memcpy(parm_list.aci_grp, all_groups, NAME_LEN);
+	ASCEBC(parm_list.aci_grp, NAME_LEN);
+	parm_list.addr = (unsigned long)addr;
 	parm_list.size = size;
 	parm_list.fmt = 0x02;
-	memset(parm_list.aci_grp, 0x40, NAME_LEN);
 	rc = -1;
 
 	diag_stat_inc(DIAG_STAT_X2FC);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/hypfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/hypfs/inode.c
@@ -496,9 +496,9 @@
 	hypfs_vm_exit();
 fail_hypfs_diag_exit:
 	hypfs_diag_exit();
+	pr_err("Initialization of hypfs failed with rc=%i\n", rc);
 fail_dbfs_exit:
 	hypfs_dbfs_exit();
-	pr_err("Initialization of hypfs failed with rc=%i\n", rc);
 	return rc;
 }
 device_initcall(hypfs_init)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/airq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/airq.h
@@ -12,10 +12,11 @@
 
 #include <linux/bit_spinlock.h>
 #include <linux/dma-mapping.h>
+#include <asm/tpi.h>
 
 struct airq_struct {
 	struct hlist_node list;		/* Handler queueing. */
-	void (*handler)(struct airq_struct *airq, bool floating);
+	void (*handler)(struct airq_struct *airq, struct tpi_info *tpi_info);
 	u8 *lsi_ptr;			/* Local-Summary-Indicator pointer */
 	u8 lsi_mask;			/* Local-Summary-Indicator mask */
 	u8 isc;				/* Interrupt-subclass */
@@ -46,8 +47,10 @@
 #define AIRQ_IV_PTR		4	/* Allocate the ptr array */
 #define AIRQ_IV_DATA		8	/* Allocate the data array */
 #define AIRQ_IV_CACHELINE	16	/* Cacheline alignment for the vector */
+#define AIRQ_IV_GUESTVEC	32	/* Vector is a pinned guest page */
 
-struct airq_iv *airq_iv_create(unsigned long bits, unsigned long flags);
+struct airq_iv *airq_iv_create(unsigned long bits, unsigned long flags,
+			       unsigned long *vec);
 void airq_iv_release(struct airq_iv *iv);
 unsigned long airq_iv_alloc(struct airq_iv *iv, unsigned long num);
 void airq_iv_free(struct airq_iv *iv, unsigned long bit, unsigned long num);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/ap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/ap.h
@@ -236,7 +236,10 @@
 	union {
 		unsigned long value;
 		struct ap_qirq_ctrl qirqctrl;
-		struct ap_queue_status status;
+		struct {
+			u32 _pad;
+			struct ap_queue_status status;
+		};
 	} reg1;
 	void *reg2 = ind;
 
@@ -250,7 +253,7 @@
 		"	lgr	%[reg1],1\n"   /* gr1 (status) into reg1 */
 		: [reg1] "+&d" (reg1)
 		: [reg0] "d" (reg0), [reg2] "d" (reg2)
-		: "cc", "0", "1", "2");
+		: "cc", "memory", "0", "1", "2");
 
 	return reg1.status;
 }
@@ -287,7 +290,10 @@
 	unsigned long reg0 = qid | (5UL << 24) | ((ifbit & 0x01) << 22);
 	union {
 		unsigned long value;
-		struct ap_queue_status status;
+		struct {
+			u32 _pad;
+			struct ap_queue_status status;
+		};
 	} reg1;
 	unsigned long reg2;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/archrandom.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/archrandom.h
@@ -2,7 +2,7 @@
 /*
  * Kernel interface for the s390 arch_random_* functions
  *
- * Copyright IBM Corp. 2017, 2020
+ * Copyright IBM Corp. 2017, 2022
  *
  * Author: Harald Freudenberger <freude@de.ibm.com>
  *
@@ -14,18 +14,15 @@
 #ifdef CONFIG_ARCH_RANDOM
 
 #include <linux/static_key.h>
+#include <linux/preempt.h>
 #include <linux/atomic.h>
+#include <asm/cpacf.h>
 
 DECLARE_STATIC_KEY_FALSE(s390_arch_random_available);
 extern atomic64_t s390_arch_random_counter;
 
-bool s390_arch_get_random_long(unsigned long *v);
-bool s390_arch_random_generate(u8 *buf, unsigned int nbytes);
-
 static inline bool __must_check arch_get_random_long(unsigned long *v)
 {
-	if (static_branch_likely(&s390_arch_random_available))
-		return s390_arch_get_random_long(v);
 	return false;
 }
 
@@ -36,16 +33,22 @@
 
 static inline bool __must_check arch_get_random_seed_long(unsigned long *v)
 {
-	if (static_branch_likely(&s390_arch_random_available)) {
-		return s390_arch_random_generate((u8 *)v, sizeof(*v));
+	if (static_branch_likely(&s390_arch_random_available) &&
+	    in_task()) {
+		cpacf_trng(NULL, 0, (u8 *)v, sizeof(*v));
+		atomic64_add(sizeof(*v), &s390_arch_random_counter);
+		return true;
 	}
 	return false;
 }
 
 static inline bool __must_check arch_get_random_seed_int(unsigned int *v)
 {
-	if (static_branch_likely(&s390_arch_random_available)) {
-		return s390_arch_random_generate((u8 *)v, sizeof(*v));
+	if (static_branch_likely(&s390_arch_random_available) &&
+	    in_task()) {
+		cpacf_trng(NULL, 0, (u8 *)v, sizeof(*v));
+		atomic64_add(sizeof(*v), &s390_arch_random_counter);
+		return true;
 	}
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/bug.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/bug.h
@@ -15,7 +15,8 @@
 		"1:	.asciz	\""__FILE__"\"\n"		\
 		".previous\n"					\
 		".section __bug_table,\"awM\",@progbits,%2\n"	\
-		"2:	.long	0b-2b,1b-2b\n"			\
+		"2:	.long	0b-.\n"				\
+		"	.long	1b-.\n"				\
 		"	.short	%0,%1\n"			\
 		"	.org	2b+%2\n"			\
 		".previous\n"					\
@@ -30,7 +31,7 @@
 	asm_inline volatile(					\
 		"0:	mc	0,0\n"				\
 		".section __bug_table,\"awM\",@progbits,%1\n"	\
-		"1:	.long	0b-1b\n"			\
+		"1:	.long	0b-.\n"				\
 		"	.short	%0\n"				\
 		"	.org	1b+%1\n"			\
 		".previous\n"					\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/cio.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/cio.h
@@ -369,7 +369,7 @@
 struct gen_pool *cio_gp_dma_create(struct device *dma_dev, int nr_pages);
 
 /* Function from drivers/s390/cio/chsc.c */
-int chsc_sstpc(void *page, unsigned int op, u16 ctrl, u64 *clock_delta);
+int chsc_sstpc(void *page, unsigned int op, u16 ctrl, long *clock_delta);
 int chsc_sstpi(void *page, void *result, size_t size);
 int chsc_stzi(void *page, void *result, size_t size);
 int chsc_sgib(u32 origin);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/cpacf.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/cpacf.h
@@ -161,28 +161,86 @@
 
 typedef struct { unsigned char bytes[16]; } cpacf_mask_t;
 
-/**
- * cpacf_query() - check if a specific CPACF function is available
- * @opcode: the opcode of the crypto instruction
- * @func: the function code to test for
- *
- * Executes the query function for the given crypto instruction @opcode
- * and checks if @func is available
- *
- * Returns 1 if @func is available for @opcode, 0 otherwise
+/*
+ * Prototype for a not existing function to produce a link
+ * error if __cpacf_query() or __cpacf_check_opcode() is used
+ * with an invalid compile time const opcode.
  */
-static __always_inline void __cpacf_query(unsigned int opcode, cpacf_mask_t *mask)
+void __cpacf_bad_opcode(void);
+
+static __always_inline void __cpacf_query_rre(u32 opc, u8 r1, u8 r2,
+					      cpacf_mask_t *mask)
 {
 	asm volatile(
-		"	lghi	0,0\n" /* query function */
-		"	lgr	1,%[mask]\n"
-		"	spm	0\n" /* pckmo doesn't change the cc */
-		/* Parameter regs are ignored, but must be nonzero and unique */
-		"0:	.insn	rrf,%[opc] << 16,2,4,6,0\n"
-		"	brc	1,0b\n"	/* handle partial completion */
-		: "=m" (*mask)
-		: [mask] "d" ((unsigned long)mask), [opc] "i" (opcode)
-		: "cc", "0", "1");
+		"	la	%%r1,%[mask]\n"
+		"	xgr	%%r0,%%r0\n"
+		"	.insn	rre,%[opc] << 16,%[r1],%[r2]\n"
+		: [mask] "=R" (*mask)
+		: [opc] "i" (opc),
+		  [r1] "i" (r1), [r2] "i" (r2)
+		: "cc", "r0", "r1");
+}
+
+static __always_inline void __cpacf_query_rrf(u32 opc,
+					      u8 r1, u8 r2, u8 r3, u8 m4,
+					      cpacf_mask_t *mask)
+{
+	asm volatile(
+		"	la	%%r1,%[mask]\n"
+		"	xgr	%%r0,%%r0\n"
+		"	.insn	rrf,%[opc] << 16,%[r1],%[r2],%[r3],%[m4]\n"
+		: [mask] "=R" (*mask)
+		: [opc] "i" (opc), [r1] "i" (r1), [r2] "i" (r2),
+		  [r3] "i" (r3), [m4] "i" (m4)
+		: "cc", "r0", "r1");
+}
+
+static __always_inline void __cpacf_query(unsigned int opcode,
+					  cpacf_mask_t *mask)
+{
+	switch (opcode) {
+	case CPACF_KDSA:
+		__cpacf_query_rre(CPACF_KDSA, 0, 2, mask);
+		break;
+	case CPACF_KIMD:
+		__cpacf_query_rre(CPACF_KIMD, 0, 2, mask);
+		break;
+	case CPACF_KLMD:
+		__cpacf_query_rre(CPACF_KLMD, 0, 2, mask);
+		break;
+	case CPACF_KM:
+		__cpacf_query_rre(CPACF_KM, 2, 4, mask);
+		break;
+	case CPACF_KMA:
+		__cpacf_query_rrf(CPACF_KMA, 2, 4, 6, 0, mask);
+		break;
+	case CPACF_KMAC:
+		__cpacf_query_rre(CPACF_KMAC, 0, 2, mask);
+		break;
+	case CPACF_KMC:
+		__cpacf_query_rre(CPACF_KMC, 2, 4, mask);
+		break;
+	case CPACF_KMCTR:
+		__cpacf_query_rrf(CPACF_KMCTR, 2, 4, 6, 0, mask);
+		break;
+	case CPACF_KMF:
+		__cpacf_query_rre(CPACF_KMF, 2, 4, mask);
+		break;
+	case CPACF_KMO:
+		__cpacf_query_rre(CPACF_KMO, 2, 4, mask);
+		break;
+	case CPACF_PCC:
+		__cpacf_query_rre(CPACF_PCC, 0, 0, mask);
+		break;
+	case CPACF_PCKMO:
+		__cpacf_query_rre(CPACF_PCKMO, 0, 0, mask);
+		break;
+	case CPACF_PRNO:
+		__cpacf_query_rre(CPACF_PRNO, 2, 4, mask);
+		break;
+	default:
+		__cpacf_bad_opcode();
+	}
 }
 
 static __always_inline int __cpacf_check_opcode(unsigned int opcode)
@@ -206,10 +264,21 @@
 	case CPACF_KMA:
 		return test_facility(146);	/* check for MSA8 */
 	default:
-		BUG();
+		__cpacf_bad_opcode();
+		return 0;
 	}
 }
 
+/**
+ * cpacf_query() - check if a specific CPACF function is available
+ * @opcode: the opcode of the crypto instruction
+ * @func: the function code to test for
+ *
+ * Executes the query function for the given crypto instruction @opcode
+ * and checks if @func is available
+ *
+ * Returns 1 if @func is available for @opcode, 0 otherwise
+ */
 static __always_inline int cpacf_query(unsigned int opcode, cpacf_mask_t *mask)
 {
 	if (__cpacf_check_opcode(opcode)) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/cpu_mf.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/cpu_mf.h
@@ -109,7 +109,9 @@
 	unsigned int AS:2;	    /* 29-30 PSW address-space control	 */
 	unsigned int I:1;	    /* 31 entry valid or invalid	 */
 	unsigned int CL:2;	    /* 32-33 Configuration Level	 */
-	unsigned int:14;
+	unsigned int H:1;	    /* 34 Host Indicator		 */
+	unsigned int LS:1;	    /* 35 Limited Sampling		 */
+	unsigned int:12;
 	unsigned int prim_asn:16;   /* primary ASN			 */
 	unsigned long long ia;	    /* Instruction Address		 */
 	unsigned long long gpp;     /* Guest Program Parameter		 */
@@ -128,19 +130,21 @@
 	struct hws_diag_entry	diag;	/* Diagnostic-sampling data entry */
 } __packed;
 
-struct hws_trailer_entry {
-	union {
-		struct {
-			unsigned int f:1;	/* 0 - Block Full Indicator   */
-			unsigned int a:1;	/* 1 - Alert request control  */
-			unsigned int t:1;	/* 2 - Timestamp format	      */
-			unsigned int :29;	/* 3 - 31: Reserved	      */
-			unsigned int bsdes:16;	/* 32-47: size of basic SDE   */
-			unsigned int dsdes:16;	/* 48-63: size of diagnostic SDE */
-		};
-		unsigned long long flags;	/* 0 - 63: All indicators     */
+union hws_trailer_header {
+	struct {
+		unsigned int f:1;	/* 0 - Block Full Indicator   */
+		unsigned int a:1;	/* 1 - Alert request control  */
+		unsigned int t:1;	/* 2 - Timestamp format	      */
+		unsigned int :29;	/* 3 - 31: Reserved	      */
+		unsigned int bsdes:16;	/* 32-47: size of basic SDE   */
+		unsigned int dsdes:16;	/* 48-63: size of diagnostic SDE */
+		unsigned long long overflow; /* 64 - Overflow Count   */
 	};
-	unsigned long long overflow;	 /* 64 - sample Overflow count	      */
+	__uint128_t val;
+};
+
+struct hws_trailer_entry {
+	union hws_trailer_header header; /* 0 - 15 Flags + Overflow Count     */
 	unsigned char timestamp[16];	 /* 16 - 31 timestamp		      */
 	unsigned long long reserved1;	 /* 32 -Reserved		      */
 	unsigned long long reserved2;	 /*				      */
@@ -287,14 +291,11 @@
 	return USEC_PER_SEC * qsi->cpu_speed / rate;
 }
 
-#define SDB_TE_ALERT_REQ_MASK	0x4000000000000000UL
-#define SDB_TE_BUFFER_FULL_MASK 0x8000000000000000UL
-
 /* Return TOD timestamp contained in an trailer entry */
 static inline unsigned long long trailer_timestamp(struct hws_trailer_entry *te)
 {
 	/* TOD in STCKE format */
-	if (te->t)
+	if (te->header.t)
 		return *((unsigned long long *) &te->timestamp[1]);
 
 	/* TOD in STCK format */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/ctl_reg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/ctl_reg.h
@@ -12,6 +12,8 @@
 
 #define CR0_CLOCK_COMPARATOR_SIGN	BIT(63 - 10)
 #define CR0_LOW_ADDRESS_PROTECTION	BIT(63 - 35)
+#define CR0_FETCH_PROTECTION_OVERRIDE	BIT(63 - 38)
+#define CR0_STORAGE_PROTECTION_OVERRIDE	BIT(63 - 39)
 #define CR0_EMERGENCY_SIGNAL_SUBMASK	BIT(63 - 49)
 #define CR0_EXTERNAL_CALL_SUBMASK	BIT(63 - 50)
 #define CR0_CLOCK_COMPARATOR_SUBMASK	BIT(63 - 52)
@@ -72,8 +74,17 @@
 	__ctl_load(reg, cr, cr);
 }
 
-void smp_ctl_set_bit(int cr, int bit);
-void smp_ctl_clear_bit(int cr, int bit);
+void smp_ctl_set_clear_bit(int cr, int bit, bool set);
+
+static inline void ctl_set_bit(int cr, int bit)
+{
+	smp_ctl_set_clear_bit(cr, bit, true);
+}
+
+static inline void ctl_clear_bit(int cr, int bit)
+{
+	smp_ctl_set_clear_bit(cr, bit, false);
+}
 
 union ctlreg0 {
 	unsigned long val;
@@ -128,8 +139,5 @@
 	};
 };
 
-#define ctl_set_bit(cr, bit) smp_ctl_set_bit(cr, bit)
-#define ctl_clear_bit(cr, bit) smp_ctl_clear_bit(cr, bit)
-
 #endif /* __ASSEMBLY__ */
 #endif /* __ASM_CTL_REG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/debug.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/debug.h
@@ -4,8 +4,8 @@
  *
  *    Copyright IBM Corp. 1999, 2020
  */
-#ifndef DEBUG_H
-#define DEBUG_H
+#ifndef _ASM_S390_DEBUG_H
+#define _ASM_S390_DEBUG_H
 
 #include <linux/string.h>
 #include <linux/spinlock.h>
@@ -487,4 +487,4 @@
 
 #endif /* MODULE */
 
-#endif /* DEBUG_H */
+#endif /* _ASM_S390_DEBUG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/dwarf.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/dwarf.h
@@ -9,6 +9,7 @@
 #define CFI_DEF_CFA_OFFSET	.cfi_def_cfa_offset
 #define CFI_ADJUST_CFA_OFFSET	.cfi_adjust_cfa_offset
 #define CFI_RESTORE		.cfi_restore
+#define CFI_REL_OFFSET		.cfi_rel_offset
 
 #ifdef CONFIG_AS_CFI_VAL_OFFSET
 #define CFI_VAL_OFFSET		.cfi_val_offset
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/extable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/extable.h
@@ -69,8 +69,13 @@
 {
 	a->fixup = b->fixup + delta;
 	b->fixup = tmp.fixup - delta;
-	a->handler = b->handler + delta;
-	b->handler = tmp.handler - delta;
+	a->handler = b->handler;
+	if (a->handler)
+		a->handler += delta;
+	b->handler = tmp.handler;
+	if (b->handler)
+		b->handler -= delta;
 }
+#define swap_ex_entry_fixup swap_ex_entry_fixup
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/facility.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/facility.h
@@ -56,8 +56,10 @@
 	unsigned long facilities_als[] = { FACILITIES_ALS };
 
 	if (__builtin_constant_p(nr) && nr < sizeof(facilities_als) * 8) {
-		if (__test_facility(nr, &facilities_als))
-			return 1;
+		if (__test_facility(nr, &facilities_als)) {
+			if (!__is_defined(__DECOMPRESSOR))
+				return 1;
+		}
 	}
 	return __test_facility(nr, &stfle_fac_list);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/fpu/api.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/fpu/api.h
@@ -78,7 +78,7 @@
 #define KERNEL_VXR_HIGH		(KERNEL_VXR_V16V23|KERNEL_VXR_V24V31)
 
 #define KERNEL_VXR		(KERNEL_VXR_LOW|KERNEL_VXR_HIGH)
-#define KERNEL_FPR		(KERNEL_FPC|KERNEL_VXR_V0V7)
+#define KERNEL_FPR		(KERNEL_FPC|KERNEL_VXR_LOW)
 
 struct kernel_fpu;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/futex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/futex.h
@@ -16,7 +16,8 @@
 		"3: jl    1b\n"						\
 		"   lhi   %0,0\n"					\
 		"4: sacf  768\n"					\
-		EX_TABLE(0b,4b) EX_TABLE(2b,4b) EX_TABLE(3b,4b)		\
+		EX_TABLE(0b,4b) EX_TABLE(1b,4b)				\
+		EX_TABLE(2b,4b) EX_TABLE(3b,4b)				\
 		: "=d" (ret), "=&d" (oldval), "=&d" (newval),		\
 		  "=m" (*uaddr)						\
 		: "0" (-EFAULT), "d" (oparg), "a" (uaddr),		\
@@ -42,7 +43,7 @@
 		break;
 	case FUTEX_OP_ANDN:
 		__futex_atomic_op("lr %2,%1\nnr %2,%5\n",
-				  ret, oldval, newval, uaddr, oparg);
+				  ret, oldval, newval, uaddr, ~oparg);
 		break;
 	case FUTEX_OP_XOR:
 		__futex_atomic_op("lr %2,%1\nxr %2,%5\n",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/gmap.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/gmap.h
@@ -148,4 +148,6 @@
 			     unsigned long gaddr, unsigned long vmaddr);
 int gmap_mark_unmergeable(void);
 void s390_reset_acc(struct mm_struct *mm);
+void s390_unlist_old_asce(struct gmap *gmap);
+int s390_replace_asce(struct gmap *gmap);
 #endif /* _ASM_S390_GMAP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/hugetlb.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/hugetlb.h
@@ -28,9 +28,11 @@
 static inline int prepare_hugepage_range(struct file *file,
 			unsigned long addr, unsigned long len)
 {
-	if (len & ~HPAGE_MASK)
+	struct hstate *h = hstate_file(file);
+
+	if (len & ~huge_page_mask(h))
 		return -EINVAL;
-	if (addr & ~HPAGE_MASK)
+	if (addr & ~huge_page_mask(h))
 		return -EINVAL;
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/ipl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/ipl.h
@@ -128,6 +128,7 @@
 			     unsigned char flags, unsigned short cert);
 int ipl_report_add_certificate(struct ipl_report *report, void *key,
 			       unsigned long addr, unsigned long len);
+bool ipl_get_secureboot(void);
 
 /*
  * DIAG 308 support
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/irq_work.h
@@ -7,6 +7,4 @@
 	return true;
 }
 
-void arch_irq_work_raise(void);
-
 #endif /* _ASM_S390_IRQ_WORK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/kexec.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/kexec.h
@@ -9,6 +9,8 @@
 #ifndef _S390_KEXEC_H
 #define _S390_KEXEC_H
 
+#include <linux/module.h>
+
 #include <asm/processor.h>
 #include <asm/page.h>
 #include <asm/setup.h>
@@ -74,7 +76,21 @@
 int arch_kexec_do_relocs(int r_type, void *loc, unsigned long val,
 			 unsigned long addr);
 
+#define ARCH_HAS_KIMAGE_ARCH
+
+struct kimage_arch {
+	void *ipl_buf;
+};
+
 extern const struct kexec_file_ops s390_kexec_image_ops;
 extern const struct kexec_file_ops s390_kexec_elf_ops;
 
+#ifdef CONFIG_KEXEC_FILE
+struct purgatory_info;
+int arch_kexec_apply_relocations_add(struct purgatory_info *pi,
+				     Elf_Shdr *section,
+				     const Elf_Shdr *relsec,
+				     const Elf_Shdr *symtab);
+#define arch_kexec_apply_relocations_add arch_kexec_apply_relocations_add
+#endif
 #endif /*_S390_KEXEC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/kprobes.h
@@ -70,7 +70,7 @@
 };
 
 void arch_remove_kprobe(struct kprobe *p);
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 
 int kprobe_fault_handler(struct pt_regs *regs, int trapnr);
 int kprobe_exceptions_notify(struct notifier_block *self,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/kvm_host.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/kvm_host.h
@@ -19,6 +19,7 @@
 #include <linux/kvm.h>
 #include <linux/seqlock.h>
 #include <linux/module.h>
+#include <linux/pci.h>
 #include <asm/debug.h>
 #include <asm/cpu.h>
 #include <asm/fpu/api.h>
@@ -252,7 +253,10 @@
 #define ECB2_IEP	0x20
 #define ECB2_PFMFI	0x08
 #define ECB2_ESCA	0x04
+#define ECB2_ZPCI_LSI	0x02
 	__u8    ecb2;                   /* 0x0062 */
+#define ECB3_AISI	0x20
+#define ECB3_AISII	0x10
 #define ECB3_DEA 0x08
 #define ECB3_AES 0x04
 #define ECB3_RI  0x01
@@ -408,6 +412,7 @@
 	u64 instruction_io_other;
 	u64 instruction_lpsw;
 	u64 instruction_lpswe;
+	u64 instruction_lpswey;
 	u64 instruction_pfmf;
 	u64 instruction_ptff;
 	u64 instruction_sck;
@@ -757,6 +762,7 @@
 	u64 inject_pfault_done;
 	u64 inject_service_signal;
 	u64 inject_virtio;
+	u64 aen_forward;
 };
 
 struct kvm_arch_memory_slot {
@@ -921,6 +927,7 @@
 	u64 guest_len;
 	unsigned long stor_base;
 	void *stor_var;
+	bool dumping;
 };
 
 struct kvm_arch{
@@ -937,6 +944,7 @@
 	int use_cmma;
 	int use_pfmfi;
 	int use_skf;
+	int use_zpci_interp;
 	int user_cpu_state_ctrl;
 	int user_sigp;
 	int user_stsi;
@@ -960,6 +968,8 @@
 	DECLARE_BITMAP(idle_mask, KVM_MAX_VCPUS);
 	struct kvm_s390_gisa_interrupt gisa_int;
 	struct kvm_s390_pv pv;
+	struct list_head kzdev_list;
+	spinlock_t kzdev_list_lock;
 };
 
 #define KVM_HVA_ERR_BAD		(-1UL)
@@ -1012,4 +1022,14 @@
 
 void kvm_arch_vcpu_block_finish(struct kvm_vcpu *vcpu);
 
+#define __KVM_HAVE_ARCH_VM_FREE
+void kvm_arch_free_vm(struct kvm *kvm);
+
+struct zpci_kvm_hook {
+	int (*kvm_register)(void *opaque, struct kvm *kvm);
+	void (*kvm_unregister)(void *opaque);
+};
+
+extern struct zpci_kvm_hook zpci_kvm_hook;
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/nospec-insn.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/nospec-insn.h
@@ -18,7 +18,12 @@
  * the various thunks are merged into a single copy.
  */
 	.macro __THUNK_PROLOG_NAME name
+#ifdef CONFIG_EXPOLINE_EXTERN
+	.pushsection .text,"ax",@progbits
+	.align 16,0x07
+#else
 	.pushsection .text.\name,"axG",@progbits,\name,comdat
+#endif
 	.globl \name
 	.hidden \name
 	.type \name,@function
@@ -26,30 +31,47 @@
 	CFI_STARTPROC
 	.endm
 
-	.macro __THUNK_EPILOG
+	.macro __THUNK_EPILOG_NAME name
 	CFI_ENDPROC
+#ifdef CONFIG_EXPOLINE_EXTERN
+	.size \name, .-\name
+#endif
 	.popsection
 	.endm
 
+#ifdef CONFIG_HAVE_MARCH_Z10_FEATURES
 	.macro __THUNK_PROLOG_BR r1,r2
-	__THUNK_PROLOG_NAME __s390_indirect_jump_r\r2\()use_r\r1
+	__THUNK_PROLOG_NAME __s390_indirect_jump_r\r1
 	.endm
 
-	.macro __THUNK_PROLOG_BC d0,r1,r2
-	__THUNK_PROLOG_NAME __s390_indirect_branch_\d0\()_\r2\()use_\r1
+	.macro __THUNK_EPILOG_BR r1,r2
+	__THUNK_EPILOG_NAME __s390_indirect_jump_r\r1
 	.endm
 
 	.macro __THUNK_BR r1,r2
-	jg	__s390_indirect_jump_r\r2\()use_r\r1
+	jg	__s390_indirect_jump_r\r1
+	.endm
+
+	.macro __THUNK_BRASL r1,r2,r3
+	brasl	\r1,__s390_indirect_jump_r\r2
+	.endm
+#else
+	.macro __THUNK_PROLOG_BR r1,r2
+	__THUNK_PROLOG_NAME __s390_indirect_jump_r\r2\()use_r\r1
 	.endm
 
-	.macro __THUNK_BC d0,r1,r2
-	jg	__s390_indirect_branch_\d0\()_\r2\()use_\r1
+	.macro __THUNK_EPILOG_BR r1,r2
+	__THUNK_EPILOG_NAME __s390_indirect_jump_r\r2\()use_r\r1
+	.endm
+
+	.macro __THUNK_BR r1,r2
+	jg	__s390_indirect_jump_r\r2\()use_r\r1
 	.endm
 
 	.macro __THUNK_BRASL r1,r2,r3
 	brasl	\r1,__s390_indirect_jump_r\r3\()use_r\r2
 	.endm
+#endif
 
 	.macro	__DECODE_RR expand,reg,ruse
 	.set __decode_fail,1
@@ -89,23 +111,6 @@
 	.endif
 	.endm
 
-	.macro	__DECODE_DRR expand,disp,reg,ruse
-	.set __decode_fail,1
-	.irp r1,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
-	.ifc \reg,%r\r1
-	.irp r2,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
-	.ifc \ruse,%r\r2
-	\expand \disp,\r1,\r2
-	.set __decode_fail,0
-	.endif
-	.endr
-	.endif
-	.endr
-	.if __decode_fail == 1
-	.error "__DECODE_DRR failed"
-	.endif
-	.endm
-
 	.macro __THUNK_EX_BR reg,ruse
 	# Be very careful when adding instructions to this macro!
 	# The ALTERNATIVE replacement code has a .+10 which targets
@@ -126,28 +131,16 @@
 555:	br	\reg
 	.endm
 
-	.macro __THUNK_EX_BC disp,reg,ruse
-#ifdef CONFIG_HAVE_MARCH_Z10_FEATURES
-	exrl	0,556f
-	j	.
-#else
-	larl	\ruse,556f
-	ex	0,0(\ruse)
-	j	.
-#endif
-556:	b	\disp(\reg)
+#ifdef CONFIG_EXPOLINE_EXTERN
+	.macro GEN_BR_THUNK reg,ruse=%r1
 	.endm
-
+	.macro GEN_BR_THUNK_EXTERN reg,ruse=%r1
+#else
 	.macro GEN_BR_THUNK reg,ruse=%r1
+#endif
 	__DECODE_RR __THUNK_PROLOG_BR,\reg,\ruse
 	__THUNK_EX_BR \reg,\ruse
-	__THUNK_EPILOG
-	.endm
-
-	.macro GEN_B_THUNK disp,reg,ruse=%r1
-	__DECODE_DRR __THUNK_PROLOG_BC,\disp,\reg,\ruse
-	__THUNK_EX_BC \disp,\reg,\ruse
-	__THUNK_EPILOG
+	__DECODE_RR __THUNK_EPILOG_BR,\reg,\ruse
 	.endm
 
 	.macro BR_EX reg,ruse=%r1
@@ -157,13 +150,6 @@
 	.popsection
 	.endm
 
-	 .macro B_EX disp,reg,ruse=%r1
-558:	__DECODE_DRR __THUNK_BC,\disp,\reg,\ruse
-	.pushsection .s390_indirect_branches,"a",@progbits
-	.long	558b-.
-	.popsection
-	.endm
-
 	.macro BASR_EX rsave,rtarget,ruse=%r1
 559:	__DECODE_RRR __THUNK_BRASL,\rsave,\rtarget,\ruse
 	.pushsection .s390_indirect_branches,"a",@progbits
@@ -175,17 +161,10 @@
 	.macro GEN_BR_THUNK reg,ruse=%r1
 	.endm
 
-	.macro GEN_B_THUNK disp,reg,ruse=%r1
-	.endm
-
 	 .macro BR_EX reg,ruse=%r1
 	br	\reg
 	.endm
 
-	 .macro B_EX disp,reg,ruse=%r1
-	b	\disp(\reg)
-	.endm
-
 	.macro BASR_EX rsave,rtarget,ruse=%r1
 	basr	\rsave,\rtarget
 	.endm
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/os_info.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/os_info.h
@@ -39,7 +39,7 @@
 
 #ifdef CONFIG_CRASH_DUMP
 void *os_info_old_entry(int nr, unsigned long *size);
-int copy_oldmem_kernel(void *dst, void *src, size_t count);
+int copy_oldmem_kernel(void *dst, unsigned long src, size_t count);
 #else
 static inline void *os_info_old_entry(int nr, unsigned long *size)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/page.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/page.h
@@ -20,6 +20,8 @@
 #define PAGE_SIZE	_PAGE_SIZE
 #define PAGE_MASK	_PAGE_MASK
 #define PAGE_DEFAULT_ACC	0
+/* storage-protection override */
+#define PAGE_SPO_ACC		9
 #define PAGE_DEFAULT_KEY	(PAGE_DEFAULT_ACC << 4)
 
 #define HPAGE_SHIFT	20
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/pci.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/pci.h
@@ -9,6 +9,7 @@
 #include <asm-generic/pci.h>
 #include <asm/pci_clp.h>
 #include <asm/pci_debug.h>
+#include <asm/pci_insn.h>
 #include <asm/sclp.h>
 
 #define PCIBIOS_MIN_IO		0x1000
@@ -97,6 +98,7 @@
 };
 
 struct s390_domain;
+struct kvm_zdev;
 
 #define ZPCI_FUNCTIONS_PER_BUS 256
 struct zpci_bus {
@@ -123,11 +125,14 @@
 	enum zpci_state state;
 	u32		fid;		/* function ID, used by sclp */
 	u32		fh;		/* function handle, used by insn's */
+	u32		gisa;		/* GISA designation for passthrough */
 	u16		vfn;		/* virtual function number */
 	u16		pchid;		/* physical channel ID */
+	u16		maxstbl;	/* Maximum store block size */
 	u8		pfgid;		/* function group ID */
 	u8		pft;		/* pci function type */
 	u8		port;
+	u8		dtsm;		/* Supported DT mask */
 	u8		rid_available	: 1;
 	u8		has_hp_slot	: 1;
 	u8		has_resources	: 1;
@@ -186,7 +191,11 @@
 
 	struct dentry	*debugfs_dev;
 
+	/* IOMMU and passthrough */
 	struct s390_domain *s390_domain; /* s390 IOMMU domain data */
+	struct kvm_zdev *kzdev;
+	struct mutex kzdev_lock;
+	struct notifier_block kvm_group_nb; /* Jammy-specific */
 };
 
 static inline bool zdev_enabled(struct zpci_dev *zdev)
@@ -198,6 +207,9 @@
 extern unsigned int s390_pci_force_floating __initdata;
 extern unsigned int s390_pci_no_rid;
 
+extern union zpci_sic_iib *zpci_aipb;
+extern struct airq_iv *zpci_aif_sbv;
+
 /* -----------------------------------------------------------------------------
   Prototypes
 ----------------------------------------------------------------------------- */
@@ -210,9 +222,11 @@
 void zpci_device_reserved(struct zpci_dev *zdev);
 bool zpci_is_device_configured(struct zpci_dev *zdev);
 
+int zpci_hot_reset_device(struct zpci_dev *zdev);
 int zpci_register_ioat(struct zpci_dev *, u8, u64, u64, u64);
 int zpci_unregister_ioat(struct zpci_dev *, u8);
 void zpci_remove_reserved_devices(void);
+void zpci_update_fh(struct zpci_dev *zdev, u32 fh);
 
 /* CLP */
 int clp_setup_writeback_mio(void);
@@ -294,8 +308,10 @@
 void zpci_debug_init_device(struct zpci_dev *, const char *);
 void zpci_debug_exit_device(struct zpci_dev *);
 
-/* Error reporting */
+/* Error handling */
 int zpci_report_error(struct pci_dev *, struct zpci_report_error_header *);
+int zpci_clear_error_state(struct zpci_dev *zdev);
+int zpci_reset_load_store_blocked(struct zpci_dev *zdev);
 
 #ifdef CONFIG_NUMA
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/pci_clp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/pci_clp.h
@@ -153,9 +153,11 @@
 	u8			:  6;
 	u8 frame		:  1;
 	u8 refresh		:  1;	/* TLB refresh mode */
-	u16 reserved2;
+	u16			:  3;
+	u16 maxstbl		: 13;	/* Maximum store block size */
 	u16 mui;
-	u16			: 16;
+	u8 dtsm;			/* Supported DT mask */
+	u8 reserved3;
 	u16 maxfaal;
 	u16			:  4;
 	u16 dnoi		: 12;
@@ -173,7 +175,8 @@
 	u16 reserved2;
 	u8 oc;				/* operation controls */
 	u8 ndas;			/* number of dma spaces */
-	u64 reserved3;
+	u32 reserved3;
+	u32 gisa;			/* GISA designation */
 } __packed;
 
 /* Set PCI function response */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/pci_insn.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/pci_insn.h
@@ -98,6 +98,15 @@
 	u32 gd;
 } __packed __aligned(8);
 
+/* Set Interruption Controls Operation Controls  */
+#define	SIC_IRQ_MODE_ALL		0
+#define	SIC_IRQ_MODE_SINGLE		1
+#define	SIC_SET_AENI_CONTROLS		2
+#define	SIC_IRQ_MODE_DIRECT		4
+#define	SIC_IRQ_MODE_D_ALL		16
+#define	SIC_IRQ_MODE_D_SINGLE		17
+#define	SIC_IRQ_MODE_SET_CPU		18
+
 /* directed interruption information block */
 struct zpci_diib {
 	u32 : 1;
@@ -119,9 +128,20 @@
 	u64 : 64;
 } __packed __aligned(8);
 
+/* adapter interruption parameters block */
+struct zpci_aipb {
+	u64 faisb;
+	u64 gait;
+	u16 : 13;
+	u16 afi : 3;
+	u32 : 32;
+	u16 faal;
+} __packed __aligned(8);
+
 union zpci_sic_iib {
 	struct zpci_diib diib;
 	struct zpci_cdiib cdiib;
+	struct zpci_aipb aipb;
 };
 
 DECLARE_STATIC_KEY_FALSE(have_mio);
@@ -134,13 +154,6 @@
 int zpci_store(const volatile void __iomem *addr, u64 data, unsigned long len);
 int __zpci_store_block(const u64 *data, u64 req, u64 offset);
 void zpci_barrier(void);
-int __zpci_set_irq_ctrl(u16 ctl, u8 isc, union zpci_sic_iib *iib);
-
-static inline int zpci_set_irq_ctrl(u16 ctl, u8 isc)
-{
-	union zpci_sic_iib iib = {{0}};
-
-	return __zpci_set_irq_ctrl(ctl, isc, &iib);
-}
+int zpci_set_irq_ctrl(u16 ctl, u8 isc, union zpci_sic_iib *iib);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/pci_io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/pci_io.h
@@ -11,15 +11,18 @@
 /* I/O size constraints */
 #define ZPCI_MAX_READ_SIZE	8
 #define ZPCI_MAX_WRITE_SIZE	128
+#define ZPCI_BOUNDARY_SIZE	(1 << 12)
+#define ZPCI_BOUNDARY_MASK	(ZPCI_BOUNDARY_SIZE - 1)
 
 /* I/O Map */
 #define ZPCI_IOMAP_SHIFT		48
-#define ZPCI_IOMAP_ADDR_BASE		0x8000000000000000UL
+#define ZPCI_IOMAP_ADDR_SHIFT		62
+#define ZPCI_IOMAP_ADDR_BASE		(1UL << ZPCI_IOMAP_ADDR_SHIFT)
 #define ZPCI_IOMAP_ADDR_OFF_MASK	((1UL << ZPCI_IOMAP_SHIFT) - 1)
 #define ZPCI_IOMAP_MAX_ENTRIES							\
-	((ULONG_MAX - ZPCI_IOMAP_ADDR_BASE + 1) / (1UL << ZPCI_IOMAP_SHIFT))
+	(1UL << (ZPCI_IOMAP_ADDR_SHIFT - ZPCI_IOMAP_SHIFT))
 #define ZPCI_IOMAP_ADDR_IDX_MASK						\
-	(~ZPCI_IOMAP_ADDR_OFF_MASK - ZPCI_IOMAP_ADDR_BASE)
+	((ZPCI_IOMAP_ADDR_BASE - 1) & ~ZPCI_IOMAP_ADDR_OFF_MASK)
 
 struct zpci_iomap_entry {
 	u32 fh;
@@ -124,16 +127,18 @@
 int zpci_write_block(volatile void __iomem *dst, const void *src,
 		     unsigned long len);
 
-static inline u8 zpci_get_max_write_size(u64 src, u64 dst, int len, int max)
+static inline int zpci_get_max_io_size(u64 src, u64 dst, int len, int max)
 {
-	int count = len > max ? max : len, size = 1;
+	int offset = dst & ZPCI_BOUNDARY_MASK;
+	int size;
 
-	while (!(src & 0x1) && !(dst & 0x1) && ((size << 1) <= count)) {
-		dst = dst >> 1;
-		src = src >> 1;
-		size = size << 1;
-	}
-	return size;
+	size = min3(len, ZPCI_BOUNDARY_SIZE - offset, max);
+	if (IS_ALIGNED(src, 8) && IS_ALIGNED(dst, 8) && IS_ALIGNED(size, 8))
+		return size;
+
+	if (size >= 8)
+		return 8;
+	return rounddown_pow_of_two(size);
 }
 
 static inline int zpci_memcpy_fromio(void *dst,
@@ -143,9 +148,9 @@
 	int size, rc = 0;
 
 	while (n > 0) {
-		size = zpci_get_max_write_size((u64 __force) src,
-					       (u64) dst, n,
-					       ZPCI_MAX_READ_SIZE);
+		size = zpci_get_max_io_size((u64 __force) src,
+					    (u64) dst, n,
+					    ZPCI_MAX_READ_SIZE);
 		rc = zpci_read_single(dst, src, size);
 		if (rc)
 			break;
@@ -165,9 +170,9 @@
 		return -EINVAL;
 
 	while (n > 0) {
-		size = zpci_get_max_write_size((u64 __force) dst,
-					       (u64) src, n,
-					       ZPCI_MAX_WRITE_SIZE);
+		size = zpci_get_max_io_size((u64 __force) dst,
+					    (u64) src, n,
+					    ZPCI_MAX_WRITE_SIZE);
 		if (size > 8) /* main path */
 			rc = zpci_write_block(dst, src, size);
 		else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/percpu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/percpu.h
@@ -31,7 +31,7 @@
 	pcp_op_T__ *ptr__;						\
 	preempt_disable_notrace();					\
 	ptr__ = raw_cpu_ptr(&(pcp));					\
-	prev__ = *ptr__;						\
+	prev__ = READ_ONCE(*ptr__);					\
 	do {								\
 		old__ = prev__;						\
 		new__ = old__ op (val);					\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/perf_event.h
@@ -75,6 +75,7 @@
 #define SAMPLE_FREQ_MODE(hwc)	(SAMPL_FLAGS(hwc) & PERF_CPUM_SF_FREQ_MODE)
 
 #define perf_arch_fetch_caller_regs(regs, __ip) do {			\
+	(regs)->psw.mask = 0;						\
 	(regs)->psw.addr = (__ip);					\
 	(regs)->gprs[15] = (unsigned long)__builtin_frame_address(0) -	\
 		offsetof(struct stack_frame, back_chain);		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/preempt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/preempt.h
@@ -46,10 +46,17 @@
 
 static inline void __preempt_count_add(int val)
 {
-	if (__builtin_constant_p(val) && (val >= -128) && (val <= 127))
-		__atomic_add_const(val, &S390_lowcore.preempt_count);
-	else
-		__atomic_add(val, &S390_lowcore.preempt_count);
+	/*
+	 * With some obscure config options and CONFIG_PROFILE_ALL_BRANCHES
+	 * enabled, gcc 12 fails to handle __builtin_constant_p().
+	 */
+	if (!IS_ENABLED(CONFIG_PROFILE_ALL_BRANCHES)) {
+		if (__builtin_constant_p(val) && (val >= -128) && (val <= 127)) {
+			__atomic_add_const(val, &S390_lowcore.preempt_count);
+			return;
+		}
+	}
+	__atomic_add(val, &S390_lowcore.preempt_count);
 }
 
 static inline void __preempt_count_sub(int val)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/processor.h
@@ -250,8 +250,8 @@
  */
 static __always_inline void __load_psw_mask(unsigned long mask)
 {
+	psw_t psw __uninitialized;
 	unsigned long addr;
-	psw_t psw;
 
 	psw.mask = mask;
 
@@ -318,14 +318,21 @@
 
 #define ARCH_LOW_ADDRESS_LIMIT	0x7fffffffUL
 
-extern int memcpy_real(void *, void *, size_t);
+extern int memcpy_real(void *, unsigned long, size_t);
 extern void memcpy_absolute(void *, void *, size_t);
 
-#define mem_assign_absolute(dest, val) do {			\
-	__typeof__(dest) __tmp = (val);				\
-								\
-	BUILD_BUG_ON(sizeof(__tmp) != sizeof(val));		\
-	memcpy_absolute(&(dest), &__tmp, sizeof(__tmp));	\
+#define put_abs_lowcore(member, x) do {					\
+	unsigned long __abs_address = offsetof(struct lowcore, member);	\
+	__typeof__(((struct lowcore *)0)->member) __tmp = (x);		\
+									\
+	memcpy_absolute(__va(__abs_address), &__tmp, sizeof(__tmp));	\
+} while (0)
+
+#define get_abs_lowcore(x, member) do {					\
+	unsigned long __abs_address = offsetof(struct lowcore, member);	\
+	__typeof__(((struct lowcore *)0)->member) *__ptr = &(x);	\
+									\
+	memcpy_absolute(__ptr, __va(__abs_address), sizeof(*__ptr));	\
 } while (0)
 
 extern int s390_isolate_bp(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/sclp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/sclp.h
@@ -88,6 +88,11 @@
 	unsigned char has_diag318 : 1;
 	unsigned char has_sipl : 1;
 	unsigned char has_dirq : 1;
+	unsigned char has_iplcc : 1;
+	unsigned char has_zpci_lsi : 1;
+	unsigned char has_aisii : 1;
+	unsigned char has_aeni : 1;
+	unsigned char has_aisi : 1;
 	unsigned int ibc;
 	unsigned int mtid;
 	unsigned int mtid_cp;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/setup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/setup.h
@@ -11,7 +11,6 @@
 #include <linux/build_bug.h>
 
 #define PARMAREA		0x10400
-#define HEAD_END		0x11000
 
 /*
  * Machine features detected in early.c
@@ -43,6 +42,8 @@
 #define STARTUP_NORMAL_OFFSET	0x10000
 #define STARTUP_KDUMP_OFFSET	0x10010
 
+#define LEGACY_COMMAND_LINE_SIZE	896
+
 #ifndef __ASSEMBLY__
 
 #include <asm/lowcore.h>
@@ -55,8 +56,9 @@
 	unsigned long oldmem_base;			/* 0x10418 */
 	unsigned long oldmem_size;			/* 0x10420 */
 	unsigned long kernel_version;			/* 0x10428 */
-	char pad1[0x10480 - 0x10430];			/* 0x10430 - 0x10480 */
-	char command_line[ARCH_COMMAND_LINE_SIZE];	/* 0x10480 */
+	unsigned long max_command_line_size;		/* 0x10430 */
+	char pad1[0x10480-0x10438];			/* 0x10438 - 0x10480 */
+	char command_line[COMMAND_LINE_SIZE];		/* 0x10480 */
 };
 
 extern struct parmarea parmarea;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/timex.h
@@ -201,6 +201,7 @@
 {
 	return (cycles_t) get_tod_clock() >> 2;
 }
+#define get_cycles get_cycles
 
 int get_phys_clock(unsigned long *clock);
 void init_cpu_timer(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/tpi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/tpi.h
@@ -19,6 +19,19 @@
 	u32 :12;
 } __packed __aligned(4);
 
+/* I/O-Interruption Code as stored by TPI for an Adapter I/O */
+struct tpi_adapter_info {
+	u32 aism:8;
+	u32 :22;
+	u32 error:1;
+	u32 forward:1;
+	u32 reserved;
+	u32 adapter_IO:1;
+	u32 directed_irq:1;
+	u32 isc:3;
+	u32 :27;
+} __packed __aligned(4);
+
 #endif /* __ASSEMBLY__ */
 
 #endif /* _ASM_S390_TPI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/uaccess.h
@@ -44,56 +44,112 @@
 #define INLINE_COPY_TO_USER
 #endif
 
+unsigned long __must_check
+_copy_from_user_key(void *to, const void __user *from, unsigned long n, unsigned long key);
+
+static __always_inline unsigned long __must_check
+copy_from_user_key(void *to, const void __user *from, unsigned long n, unsigned long key)
+{
+	if (likely(check_copy_size(to, n, false)))
+		n = _copy_from_user_key(to, from, n, key);
+	return n;
+}
+
+unsigned long __must_check
+_copy_to_user_key(void __user *to, const void *from, unsigned long n, unsigned long key);
+
+static __always_inline unsigned long __must_check
+copy_to_user_key(void __user *to, const void *from, unsigned long n, unsigned long key)
+{
+	if (likely(check_copy_size(from, n, true)))
+		n = _copy_to_user_key(to, from, n, key);
+	return n;
+}
+
 int __put_user_bad(void) __attribute__((noreturn));
 int __get_user_bad(void) __attribute__((noreturn));
 
+union oac {
+	unsigned int val;
+	struct {
+		struct {
+			unsigned short key : 4;
+			unsigned short	   : 4;
+			unsigned short as  : 2;
+			unsigned short	   : 4;
+			unsigned short k   : 1;
+			unsigned short a   : 1;
+		} oac1;
+		struct {
+			unsigned short key : 4;
+			unsigned short	   : 4;
+			unsigned short as  : 2;
+			unsigned short	   : 4;
+			unsigned short k   : 1;
+			unsigned short a   : 1;
+		} oac2;
+	};
+};
+
 #ifdef CONFIG_HAVE_MARCH_Z10_FEATURES
 
-#define __put_get_user_asm(to, from, size, insn)		\
-({								\
-	int __rc;						\
-								\
-	asm volatile(						\
-		insn "		0,%[spec]\n"			\
-		"0:	mvcos	%[_to],%[_from],%[_size]\n"	\
-		"1:	xr	%[rc],%[rc]\n"			\
-		"2:\n"						\
-		".pushsection .fixup, \"ax\"\n"			\
-		"3:	lhi	%[rc],%[retval]\n"		\
-		"	jg	2b\n"				\
-		".popsection\n"					\
-		EX_TABLE(0b,3b) EX_TABLE(1b,3b)			\
-		: [rc] "=&d" (__rc), [_to] "+Q" (*(to))		\
-		: [_size] "d" (size), [_from] "Q" (*(from)),	\
-		  [retval] "K" (-EFAULT), [spec] "K" (0x81UL)	\
-		: "cc", "0");					\
-	__rc;							\
+#define __put_get_user_asm(to, from, size, oac_spec)			\
+({									\
+	int __rc;							\
+									\
+	asm volatile(							\
+		"	lr	0,%[spec]\n"				\
+		"0:	mvcos	%[_to],%[_from],%[_size]\n"		\
+		"1:	xr	%[rc],%[rc]\n"				\
+		"2:\n"							\
+		".pushsection .fixup, \"ax\"\n"				\
+		"3:	lhi	%[rc],%[retval]\n"			\
+		"	jg	2b\n"					\
+		".popsection\n"						\
+		EX_TABLE(0b,3b) EX_TABLE(1b,3b)				\
+		: [rc] "=&d" (__rc), [_to] "+Q" (*(to))			\
+		: [_size] "d" (size), [_from] "Q" (*(from)),		\
+		  [retval] "K" (-EFAULT), [spec] "d" (oac_spec.val)	\
+		: "cc", "0");						\
+	__rc;								\
 })
 
+#define __put_user_asm(to, from, size)				\
+	__put_get_user_asm(to, from, size, ((union oac) {	\
+		.oac1.as = PSW_BITS_AS_SECONDARY,		\
+		.oac1.a = 1					\
+	}))
+
+#define __get_user_asm(to, from, size)				\
+	__put_get_user_asm(to, from, size, ((union oac) {	\
+		.oac2.as = PSW_BITS_AS_SECONDARY,		\
+		.oac2.a = 1					\
+	}))							\
+
 static __always_inline int __put_user_fn(void *x, void __user *ptr, unsigned long size)
 {
 	int rc;
 
 	switch (size) {
 	case 1:
-		rc = __put_get_user_asm((unsigned char __user *)ptr,
-					(unsigned char *)x,
-					size, "llilh");
+		rc = __put_user_asm((unsigned char __user *)ptr,
+				    (unsigned char *)x,
+				    size);
 		break;
 	case 2:
-		rc = __put_get_user_asm((unsigned short __user *)ptr,
-					(unsigned short *)x,
-					size, "llilh");
+		rc = __put_user_asm((unsigned short __user *)ptr,
+				    (unsigned short *)x,
+				    size);
 		break;
 	case 4:
-		rc = __put_get_user_asm((unsigned int __user *)ptr,
-					(unsigned int *)x,
-					size, "llilh");
+		rc = __put_user_asm((unsigned int __user *)ptr,
+				    (unsigned int *)x,
+				    size);
 		break;
 	case 8:
-		rc = __put_get_user_asm((unsigned long __user *)ptr,
-					(unsigned long *)x,
-					size, "llilh");
+		rc = __put_user_asm((unsigned long __user *)ptr,
+				    (unsigned long *)x,
+				    size);
 		break;
 	default:
 		__put_user_bad();
@@ -108,24 +164,24 @@
 
 	switch (size) {
 	case 1:
-		rc = __put_get_user_asm((unsigned char *)x,
-					(unsigned char __user *)ptr,
-					size, "lghi");
+		rc = __get_user_asm((unsigned char *)x,
+				    (unsigned char __user *)ptr,
+				    size);
 		break;
 	case 2:
-		rc = __put_get_user_asm((unsigned short *)x,
-					(unsigned short __user *)ptr,
-					size, "lghi");
+		rc = __get_user_asm((unsigned short *)x,
+				    (unsigned short __user *)ptr,
+				    size);
 		break;
 	case 4:
-		rc = __put_get_user_asm((unsigned int *)x,
-					(unsigned int __user *)ptr,
-					size, "lghi");
+		rc = __get_user_asm((unsigned int *)x,
+				    (unsigned int __user *)ptr,
+				    size);
 		break;
 	case 8:
-		rc = __put_get_user_asm((unsigned long *)x,
-					(unsigned long __user *)ptr,
-					size, "lghi");
+		rc = __get_user_asm((unsigned long *)x,
+				    (unsigned long __user *)ptr,
+				    size);
 		break;
 	default:
 		__get_user_bad();
@@ -245,7 +301,7 @@
 	return __clear_user(to, n);
 }
 
-int copy_to_user_real(void __user *dest, void *src, unsigned long count);
+int copy_to_user_real(void __user *dest, unsigned long src, unsigned long count);
 void *s390_kernel_write(void *dst, const void *src, size_t size);
 
 #define HAVE_GET_KERNEL_NOFAULT
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/unwind.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/unwind.h
@@ -4,6 +4,8 @@
 
 #include <linux/sched.h>
 #include <linux/ftrace.h>
+#include <linux/kprobes.h>
+#include <linux/llist.h>
 #include <asm/ptrace.h>
 #include <asm/stacktrace.h>
 
@@ -36,10 +38,21 @@
 	struct pt_regs *regs;
 	unsigned long sp, ip;
 	int graph_idx;
+	struct llist_node *kr_cur;
 	bool reliable;
 	bool error;
 };
 
+/* Recover the return address modified by kretprobe and ftrace_graph. */
+static inline unsigned long unwind_recover_ret_addr(struct unwind_state *state,
+						    unsigned long ip)
+{
+	ip = ftrace_graph_ret_addr(state->task, &state->graph_idx, ip, (void *)state->sp);
+	if (is_kretprobe_trampoline(ip))
+		ip = kretprobe_find_ret_addr(state->task, (void *)state->sp, &state->kr_cur);
+	return ip;
+}
+
 void __unwind_start(struct unwind_state *state, struct task_struct *task,
 		    struct pt_regs *regs, unsigned long first_frame);
 bool unwind_next_frame(struct unwind_state *state);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/uv.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/uv.h
@@ -2,7 +2,7 @@
 /*
  * Ultravisor Interfaces
  *
- * Copyright IBM Corp. 2019
+ * Copyright IBM Corp. 2019, 2022
  *
  * Author(s):
  *	Vasily Gorbik <gor@linux.ibm.com>
@@ -18,6 +18,11 @@
 #include <asm/page.h>
 #include <asm/gmap.h>
 
+#define UVC_CC_OK	0
+#define UVC_CC_ERROR	1
+#define UVC_CC_BUSY	2
+#define UVC_CC_PARTIAL	3
+
 #define UVC_RC_EXECUTED		0x0001
 #define UVC_RC_INV_CMD		0x0002
 #define UVC_RC_INV_STATE	0x0003
@@ -45,8 +50,13 @@
 #define UVC_CMD_SET_UNSHARE_ALL		0x0340
 #define UVC_CMD_PIN_PAGE_SHARED		0x0341
 #define UVC_CMD_UNPIN_PAGE_SHARED	0x0342
+#define UVC_CMD_DUMP_INIT		0x0400
+#define UVC_CMD_DUMP_CONF_STOR_STATE	0x0401
+#define UVC_CMD_DUMP_CPU		0x0402
+#define UVC_CMD_DUMP_COMPLETE		0x0403
 #define UVC_CMD_SET_SHARED_ACCESS	0x1000
 #define UVC_CMD_REMOVE_SHARED_ACCESS	0x1001
+#define UVC_CMD_RETR_ATTEST		0x1020
 
 /* Bits in installed uv calls */
 enum uv_cmds_inst {
@@ -71,10 +81,16 @@
 	BIT_UVC_CMD_UNSHARE_ALL = 20,
 	BIT_UVC_CMD_PIN_PAGE_SHARED = 21,
 	BIT_UVC_CMD_UNPIN_PAGE_SHARED = 22,
+	BIT_UVC_CMD_DUMP_INIT = 24,
+	BIT_UVC_CMD_DUMP_CONFIG_STOR_STATE = 25,
+	BIT_UVC_CMD_DUMP_CPU = 26,
+	BIT_UVC_CMD_DUMP_COMPLETE = 27,
+	BIT_UVC_CMD_RETR_ATTEST = 28,
 };
 
 enum uv_feat_ind {
 	BIT_UV_FEAT_MISC = 0,
+	BIT_UV_FEAT_AIV = 1,
 };
 
 struct uv_cb_header {
@@ -86,23 +102,29 @@
 
 /* Query Ultravisor Information */
 struct uv_cb_qui {
-	struct uv_cb_header header;
-	u64 reserved08;
-	u64 inst_calls_list[4];
-	u64 reserved30[2];
-	u64 uv_base_stor_len;
-	u64 reserved48;
-	u64 conf_base_phys_stor_len;
-	u64 conf_base_virt_stor_len;
-	u64 conf_virt_var_stor_len;
-	u64 cpu_stor_len;
-	u32 reserved70[3];
-	u32 max_num_sec_conf;
-	u64 max_guest_stor_addr;
-	u8  reserved88[158 - 136];
-	u16 max_guest_cpu_id;
-	u64 uv_feature_indications;
-	u8  reserveda0[200 - 168];
+	struct uv_cb_header header;		/* 0x0000 */
+	u64 reserved08;				/* 0x0008 */
+	u64 inst_calls_list[4];			/* 0x0010 */
+	u64 reserved30[2];			/* 0x0030 */
+	u64 uv_base_stor_len;			/* 0x0040 */
+	u64 reserved48;				/* 0x0048 */
+	u64 conf_base_phys_stor_len;		/* 0x0050 */
+	u64 conf_base_virt_stor_len;		/* 0x0058 */
+	u64 conf_virt_var_stor_len;		/* 0x0060 */
+	u64 cpu_stor_len;			/* 0x0068 */
+	u32 reserved70[3];			/* 0x0070 */
+	u32 max_num_sec_conf;			/* 0x007c */
+	u64 max_guest_stor_addr;		/* 0x0080 */
+	u8  reserved88[158 - 136];		/* 0x0088 */
+	u16 max_guest_cpu_id;			/* 0x009e */
+	u64 uv_feature_indications;		/* 0x00a0 */
+	u64 reserveda8;				/* 0x00a8 */
+	u64 supp_se_hdr_versions;		/* 0x00b0 */
+	u64 supp_se_hdr_pcf;			/* 0x00b8 */
+	u64 reservedc0;				/* 0x00c0 */
+	u64 conf_dump_storage_state_len;	/* 0x00c8 */
+	u64 conf_dump_finalize_len;		/* 0x00d0 */
+	u8  reservedd8[256 - 216];		/* 0x00d8 */
 } __packed __aligned(8);
 
 /* Initialize Ultravisor */
@@ -213,6 +235,50 @@
 	u64 reserved28;
 } __packed __aligned(8);
 
+/* Retrieve Attestation Measurement */
+struct uv_cb_attest {
+	struct uv_cb_header header;	/* 0x0000 */
+	u64 reserved08[2];		/* 0x0008 */
+	u64 arcb_addr;			/* 0x0018 */
+	u64 cont_token;			/* 0x0020 */
+	u8  reserved28[6];		/* 0x0028 */
+	u16 user_data_len;		/* 0x002e */
+	u8  user_data[256];		/* 0x0030 */
+	u32 reserved130[3];		/* 0x0130 */
+	u32 meas_len;			/* 0x013c */
+	u64 meas_addr;			/* 0x0140 */
+	u8  config_uid[16];		/* 0x0148 */
+	u32 reserved158;		/* 0x0158 */
+	u32 add_data_len;		/* 0x015c */
+	u64 add_data_addr;		/* 0x0160 */
+	u64 reserved168[4];		/* 0x0168 */
+} __packed __aligned(8);
+
+struct uv_cb_dump_cpu {
+	struct uv_cb_header header;
+	u64 reserved08[2];
+	u64 cpu_handle;
+	u64 dump_area_origin;
+	u64 reserved28[5];
+} __packed __aligned(8);
+
+struct uv_cb_dump_stor_state {
+	struct uv_cb_header header;
+	u64 reserved08[2];
+	u64 config_handle;
+	u64 dump_area_origin;
+	u64 gaddr;
+	u64 reserved28[4];
+} __packed __aligned(8);
+
+struct uv_cb_dump_complete {
+	struct uv_cb_header header;
+	u64 reserved08[2];
+	u64 config_handle;
+	u64 dump_area_origin;
+	u64 reserved30[5];
+} __packed __aligned(8);
+
 static inline int __uv_call(unsigned long r1, unsigned long r2)
 {
 	int cc;
@@ -280,6 +346,10 @@
 	unsigned int max_num_sec_conf;
 	unsigned short max_guest_cpu_id;
 	unsigned long uv_feature_indications;
+	unsigned long supp_se_hdr_ver;
+	unsigned long supp_se_hdr_pcf;
+	unsigned long conf_dump_storage_state_len;
+	unsigned long conf_dump_finalize_len;
 };
 
 extern struct uv_info uv_info;
@@ -312,7 +382,10 @@
 
 	if (!uv_call(0, (u64)&uvcb))
 		return 0;
-	return -EINVAL;
+	pr_err("%s UVC failed (rc: 0x%x, rrc: 0x%x), possible hypervisor bug.\n",
+	       uvcb.header.cmd == UVC_CMD_SET_SHARED_ACCESS ? "Share" : "Unshare",
+	       uvcb.header.rc, uvcb.header.rrc);
+	panic("System security cannot be guaranteed unless the system panics now.\n");
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/asm/vx-insn.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/asm/vx-insn.h
@@ -372,6 +372,16 @@
 	MRXBOPC	\hint, 0x36, v1, v3
 .endm
 
+/* VECTOR STORE */
+.macro	VST	vr1, disp, index="%r0", base
+	VX_NUM	v1, \vr1
+	GR_NUM	x2, \index
+	GR_NUM	b2, \base	    /* Base register */
+	.word	0xE700 | ((v1&15) << 4) | (x2&15)
+	.word	(b2 << 12) | (\disp)
+	MRXBOPC	0, 0x0E, v1
+.endm
+
 /* VECTOR STORE MULTIPLE */
 .macro	VSTM	vfrom, vto, disp, base, hint=3
 	VX_NUM	v1, \vfrom
@@ -411,6 +421,81 @@
 	VUPLL	\vr1, \vr2, 2
 .endm
 
+/* VECTOR PERMUTE DOUBLEWORD IMMEDIATE */
+.macro	VPDI	vr1, vr2, vr3, m4
+	VX_NUM	v1, \vr1
+	VX_NUM	v2, \vr2
+	VX_NUM	v3, \vr3
+	.word	0xE700 | ((v1&15) << 4) | (v2&15)
+	.word	((v3&15) << 12)
+	MRXBOPC	\m4, 0x84, v1, v2, v3
+.endm
+
+/* VECTOR REPLICATE */
+.macro	VREP	vr1, vr3, imm2, m4
+	VX_NUM	v1, \vr1
+	VX_NUM	v3, \vr3
+	.word	0xE700 | ((v1&15) << 4) | (v3&15)
+	.word	\imm2
+	MRXBOPC	\m4, 0x4D, v1, v3
+.endm
+.macro	VREPB	vr1, vr3, imm2
+	VREP	\vr1, \vr3, \imm2, 0
+.endm
+.macro	VREPH	vr1, vr3, imm2
+	VREP	\vr1, \vr3, \imm2, 1
+.endm
+.macro	VREPF	vr1, vr3, imm2
+	VREP	\vr1, \vr3, \imm2, 2
+.endm
+.macro	VREPG	vr1, vr3, imm2
+	VREP	\vr1, \vr3, \imm2, 3
+.endm
+
+/* VECTOR MERGE HIGH */
+.macro	VMRH	vr1, vr2, vr3, m4
+	VX_NUM	v1, \vr1
+	VX_NUM	v2, \vr2
+	VX_NUM	v3, \vr3
+	.word	0xE700 | ((v1&15) << 4) | (v2&15)
+	.word	((v3&15) << 12)
+	MRXBOPC	\m4, 0x61, v1, v2, v3
+.endm
+.macro	VMRHB	vr1, vr2, vr3
+	VMRH	\vr1, \vr2, \vr3, 0
+.endm
+.macro	VMRHH	vr1, vr2, vr3
+	VMRH	\vr1, \vr2, \vr3, 1
+.endm
+.macro	VMRHF	vr1, vr2, vr3
+	VMRH	\vr1, \vr2, \vr3, 2
+.endm
+.macro	VMRHG	vr1, vr2, vr3
+	VMRH	\vr1, \vr2, \vr3, 3
+.endm
+
+/* VECTOR MERGE LOW */
+.macro	VMRL	vr1, vr2, vr3, m4
+	VX_NUM	v1, \vr1
+	VX_NUM	v2, \vr2
+	VX_NUM	v3, \vr3
+	.word	0xE700 | ((v1&15) << 4) | (v2&15)
+	.word	((v3&15) << 12)
+	MRXBOPC	\m4, 0x60, v1, v2, v3
+.endm
+.macro	VMRLB	vr1, vr2, vr3
+	VMRL	\vr1, \vr2, \vr3, 0
+.endm
+.macro	VMRLH	vr1, vr2, vr3
+	VMRL	\vr1, \vr2, \vr3, 1
+.endm
+.macro	VMRLF	vr1, vr2, vr3
+	VMRL	\vr1, \vr2, \vr3, 2
+.endm
+.macro	VMRLG	vr1, vr2, vr3
+	VMRL	\vr1, \vr2, \vr3, 3
+.endm
+
 
 /* Vector integer instructions */
 
@@ -557,5 +642,37 @@
 	VESRAV	\vr1, \vr2, \vr3, 3
 .endm
 
+/* VECTOR ELEMENT ROTATE LEFT LOGICAL */
+.macro	VERLL	vr1, vr3, disp, base="%r0", m4
+	VX_NUM	v1, \vr1
+	VX_NUM	v3, \vr3
+	GR_NUM	b2, \base
+	.word	0xE700 | ((v1&15) << 4) | (v3&15)
+	.word	(b2 << 12) | (\disp)
+	MRXBOPC	\m4, 0x33, v1, v3
+.endm
+.macro	VERLLB	vr1, vr3, disp, base="%r0"
+	VERLL	\vr1, \vr3, \disp, \base, 0
+.endm
+.macro	VERLLH	vr1, vr3, disp, base="%r0"
+	VERLL	\vr1, \vr3, \disp, \base, 1
+.endm
+.macro	VERLLF	vr1, vr3, disp, base="%r0"
+	VERLL	\vr1, \vr3, \disp, \base, 2
+.endm
+.macro	VERLLG	vr1, vr3, disp, base="%r0"
+	VERLL	\vr1, \vr3, \disp, \base, 3
+.endm
+
+/* VECTOR SHIFT LEFT DOUBLE BY BYTE */
+.macro	VSLDB	vr1, vr2, vr3, imm4
+	VX_NUM	v1, \vr1
+	VX_NUM	v2, \vr2
+	VX_NUM	v3, \vr3
+	.word	0xE700 | ((v1&15) << 4) | (v2&15)
+	.word	((v3&15) << 12) | (\imm4)
+	MRXBOPC	0, 0x77, v1, v2, v3
+.endm
+
 #endif	/* __ASSEMBLY__ */
 #endif	/* __ASM_S390_VX_INSN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/uapi/asm/dasd.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/uapi/asm/dasd.h
@@ -78,6 +78,7 @@
  * 0x040: give access to raw eckd data
  * 0x080: enable discard support
  * 0x100: enable autodisable for IFCC errors (default)
+ * 0x200: enable requeue of all requests on autoquiesce
  */
 #define DASD_FEATURE_READONLY	      0x001
 #define DASD_FEATURE_USEDIAG	      0x002
@@ -88,6 +89,7 @@
 #define DASD_FEATURE_USERAW	      0x040
 #define DASD_FEATURE_DISCARD	      0x080
 #define DASD_FEATURE_PATH_AUTODISABLE 0x100
+#define DASD_FEATURE_REQUEUEQUIESCE   0x200
 #define DASD_FEATURE_DEFAULT	      DASD_FEATURE_PATH_AUTODISABLE
 
 #define DASD_PARTN_BITS 2
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/uapi/asm/setup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/uapi/asm/setup.h
@@ -9,6 +9,4 @@
 
 #define COMMAND_LINE_SIZE	4096
 
-#define ARCH_COMMAND_LINE_SIZE	896
-
 #endif /* _UAPI_ASM_S390_SETUP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/uapi/asm/uvdevice.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/uapi/asm/uvdevice.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ *  Copyright IBM Corp. 2022
+ *  Author(s): Steffen Eiden <seiden@linux.ibm.com>
+ */
+#ifndef __S390_ASM_UVDEVICE_H
+#define __S390_ASM_UVDEVICE_H
+
+#include <linux/types.h>
+
+struct uvio_ioctl_cb {
+	__u32 flags;
+	__u16 uv_rc;			/* UV header rc value */
+	__u16 uv_rrc;			/* UV header rrc value */
+	__u64 argument_addr;		/* Userspace address of uvio argument */
+	__u32 argument_len;
+	__u8  reserved14[0x40 - 0x14];	/* must be zero */
+};
+
+#define UVIO_ATT_USER_DATA_LEN		0x100
+#define UVIO_ATT_UID_LEN		0x10
+struct uvio_attest {
+	__u64 arcb_addr;				/* 0x0000 */
+	__u64 meas_addr;				/* 0x0008 */
+	__u64 add_data_addr;				/* 0x0010 */
+	__u8  user_data[UVIO_ATT_USER_DATA_LEN];	/* 0x0018 */
+	__u8  config_uid[UVIO_ATT_UID_LEN];		/* 0x0118 */
+	__u32 arcb_len;					/* 0x0128 */
+	__u32 meas_len;					/* 0x012c */
+	__u32 add_data_len;				/* 0x0130 */
+	__u16 user_data_len;				/* 0x0134 */
+	__u16 reserved136;				/* 0x0136 */
+};
+
+/*
+ * The following max values define an upper length for the IOCTL in/out buffers.
+ * However, they do not represent the maximum the Ultravisor allows which is
+ * often way smaller. By allowing larger buffer sizes we hopefully do not need
+ * to update the code with every machine update. It is therefore possible for
+ * userspace to request more memory than actually used by kernel/UV.
+ */
+#define UVIO_ATT_ARCB_MAX_LEN		0x100000
+#define UVIO_ATT_MEASUREMENT_MAX_LEN	0x8000
+#define UVIO_ATT_ADDITIONAL_MAX_LEN	0x8000
+
+#define UVIO_DEVICE_NAME "uv"
+#define UVIO_TYPE_UVC 'u'
+
+#define UVIO_IOCTL_ATT _IOWR(UVIO_TYPE_UVC, 0x01, struct uvio_ioctl_cb)
+
+#endif /* __S390_ASM_UVDEVICE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/include/uapi/asm/zcrypt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/include/uapi/asm/zcrypt.h
@@ -288,7 +288,7 @@
  *	 0x08: CEX3A
  *	 0x0a: CEX4
  *	 0x0b: CEX5
- *	 0x0c: CEX6 and CEX7
+ *	 0x0c: CEX6, CEX7 or CEX8
  *	 0x0d: device is disabled
  *
  *   ZCRYPT_QDEPTH_MASK
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/asm-offsets.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/asm-offsets.c
@@ -128,6 +128,8 @@
 	OFFSET(__LC_BR_R1, lowcore, br_r1_trampoline);
 	/* software defined ABI-relevant lowcore locations 0xe00 - 0xe20 */
 	OFFSET(__LC_DUMP_REIPL, lowcore, ipib);
+	OFFSET(__LC_VMCORE_INFO, lowcore, vmcore_info);
+	OFFSET(__LC_OS_INFO, lowcore, os_info);
 	/* hardware defined lowcore locations 0x1000 - 0x18ff */
 	OFFSET(__LC_MCESAD, lowcore, mcesad);
 	OFFSET(__LC_EXT_PARAMS2, lowcore, ext_params2);
@@ -160,5 +162,6 @@
 	DEFINE(OLDMEM_BASE, PARMAREA + offsetof(struct parmarea, oldmem_base));
 	DEFINE(OLDMEM_SIZE, PARMAREA + offsetof(struct parmarea, oldmem_size));
 	DEFINE(COMMAND_LINE, PARMAREA + offsetof(struct parmarea, command_line));
+	DEFINE(MAX_COMMAND_LINE_SIZE, PARMAREA + offsetof(struct parmarea, max_command_line_size));
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/crash_dump.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/crash_dump.c
@@ -44,7 +44,7 @@
 	u64 fprs[16];
 	u32 fpc;
 	u32 prefix;
-	u64 todpreg;
+	u32 todpreg;
 	u64 timer;
 	u64 todcmp;
 	u64 vxrs_low[16];
@@ -132,28 +132,27 @@
 /*
  * Copy memory of the old, dumped system to a kernel space virtual address
  */
-int copy_oldmem_kernel(void *dst, void *src, size_t count)
+int copy_oldmem_kernel(void *dst, unsigned long src, size_t count)
 {
-	unsigned long from, len;
+	unsigned long len;
 	void *ra;
 	int rc;
 
 	while (count) {
-		from = __pa(src);
-		if (!oldmem_data.start && from < sclp.hsa_size) {
+		if (!oldmem_data.start && src < sclp.hsa_size) {
 			/* Copy from zfcp/nvme dump HSA area */
-			len = min(count, sclp.hsa_size - from);
-			rc = memcpy_hsa_kernel(dst, from, len);
+			len = min(count, sclp.hsa_size - src);
+			rc = memcpy_hsa_kernel(dst, src, len);
 			if (rc)
 				return rc;
 		} else {
 			/* Check for swapped kdump oldmem areas */
-			if (oldmem_data.start && from - oldmem_data.start < oldmem_data.size) {
-				from -= oldmem_data.start;
-				len = min(count, oldmem_data.size - from);
-			} else if (oldmem_data.start && from < oldmem_data.size) {
-				len = min(count, oldmem_data.size - from);
-				from += oldmem_data.start;
+			if (oldmem_data.start && src - oldmem_data.start < oldmem_data.size) {
+				src -= oldmem_data.start;
+				len = min(count, oldmem_data.size - src);
+			} else if (oldmem_data.start && src < oldmem_data.size) {
+				len = min(count, oldmem_data.size - src);
+				src += oldmem_data.start;
 			} else {
 				len = count;
 			}
@@ -163,7 +162,7 @@
 			} else {
 				ra = dst;
 			}
-			if (memcpy_real(ra, (void *) from, len))
+			if (memcpy_real(ra, src, len))
 				return -EFAULT;
 		}
 		dst += len;
@@ -176,31 +175,30 @@
 /*
  * Copy memory of the old, dumped system to a user space virtual address
  */
-static int copy_oldmem_user(void __user *dst, void *src, size_t count)
+static int copy_oldmem_user(void __user *dst, unsigned long src, size_t count)
 {
-	unsigned long from, len;
+	unsigned long len;
 	int rc;
 
 	while (count) {
-		from = __pa(src);
-		if (!oldmem_data.start && from < sclp.hsa_size) {
+		if (!oldmem_data.start && src < sclp.hsa_size) {
 			/* Copy from zfcp/nvme dump HSA area */
-			len = min(count, sclp.hsa_size - from);
-			rc = memcpy_hsa_user(dst, from, len);
+			len = min(count, sclp.hsa_size - src);
+			rc = memcpy_hsa_user(dst, src, len);
 			if (rc)
 				return rc;
 		} else {
 			/* Check for swapped kdump oldmem areas */
-			if (oldmem_data.start && from - oldmem_data.size < oldmem_data.size) {
-				from -= oldmem_data.size;
-				len = min(count, oldmem_data.size - from);
-			} else if (oldmem_data.start && from < oldmem_data.size) {
-				len = min(count, oldmem_data.size - from);
-				from += oldmem_data.start;
+			if (oldmem_data.start && src - oldmem_data.start < oldmem_data.size) {
+				src -= oldmem_data.start;
+				len = min(count, oldmem_data.size - src);
+			} else if (oldmem_data.start && src < oldmem_data.size) {
+				len = min(count, oldmem_data.size - src);
+				src += oldmem_data.start;
 			} else {
 				len = count;
 			}
-			rc = copy_to_user_real(dst, (void *) from, count);
+			rc = copy_to_user_real(dst, src, len);
 			if (rc)
 				return rc;
 		}
@@ -217,12 +215,12 @@
 ssize_t copy_oldmem_page(unsigned long pfn, char *buf, size_t csize,
 			 unsigned long offset, int userbuf)
 {
-	void *src;
+	unsigned long src;
 	int rc;
 
 	if (!csize)
 		return 0;
-	src = (void *) (pfn << PAGE_SHIFT) + offset;
+	src = pfn_to_phys(pfn) + offset;
 	if (userbuf)
 		rc = copy_oldmem_user((void __force __user *) buf, src, csize);
 	else
@@ -429,10 +427,10 @@
 static void *get_vmcoreinfo_old(unsigned long *size)
 {
 	char nt_name[11], *vmcoreinfo;
+	unsigned long addr;
 	Elf64_Nhdr note;
-	void *addr;
 
-	if (copy_oldmem_kernel(&addr, &S390_lowcore.vmcore_info, sizeof(addr)))
+	if (copy_oldmem_kernel(&addr, __LC_VMCORE_INFO, sizeof(addr)))
 		return NULL;
 	memset(nt_name, 0, sizeof(nt_name));
 	if (copy_oldmem_kernel(&note, addr, sizeof(note)))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/dumpstack.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/dumpstack.c
@@ -224,5 +224,5 @@
 	if (panic_on_oops)
 		panic("Fatal exception: panic_on_oops");
 	oops_exit();
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/early.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/early.c
@@ -250,15 +250,9 @@
 #endif
 }
 
-static inline void setup_control_registers(void)
+static inline void setup_low_address_protection(void)
 {
-	unsigned long reg;
-
-	__ctl_store(reg, 0, 0);
-	reg |= CR0_LOW_ADDRESS_PROTECTION;
-	reg |= CR0_EMERGENCY_SIGNAL_SUBMASK;
-	reg |= CR0_EXTERNAL_CALL_SUBMASK;
-	__ctl_load(reg, 0, 0);
+	__ctl_set_bit(0, 28);
 }
 
 static inline void setup_access_registers(void)
@@ -280,7 +274,7 @@
 static void __init setup_boot_command_line(void)
 {
 	/* copy arch command line */
-	strlcpy(boot_command_line, early_command_line, ARCH_COMMAND_LINE_SIZE);
+	strlcpy(boot_command_line, early_command_line, COMMAND_LINE_SIZE);
 }
 
 static void __init check_image_bootable(void)
@@ -311,7 +305,7 @@
 	save_vector_registers();
 	setup_topology();
 	sclp_early_detect();
-	setup_control_registers();
+	setup_low_address_protection();
 	setup_access_registers();
 	lockdep_on();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/entry.S
@@ -175,7 +175,6 @@
 #endif
 
 	GEN_BR_THUNK %r14
-	GEN_BR_THUNK %r14,%r13
 
 	.section .kprobes.text, "ax"
 .Ldummy:
@@ -248,6 +247,10 @@
 	BPEXIT	__SF_SIE_FLAGS(%r15),(_TIF_ISOLATE_BP|_TIF_ISOLATE_BP_GUEST)
 .Lsie_entry:
 	sie	0(%r14)
+# Let the next instruction be NOP to avoid triggering a machine check
+# and handling it in a guest as result of the instruction execution.
+	nopr	7
+.Lsie_leave:
 	BPOFF
 	BPENTER	__SF_SIE_FLAGS(%r15),(_TIF_ISOLATE_BP|_TIF_ISOLATE_BP_GUEST)
 .Lsie_skip:
@@ -470,9 +473,13 @@
 ENDPROC(\name)
 .endm
 
+	.section .irqentry.text, "ax"
+
 INT_HANDLER ext_int_handler,__LC_EXT_OLD_PSW,do_ext_irq
 INT_HANDLER io_int_handler,__LC_IO_OLD_PSW,do_io_irq
 
+	.section .kprobes.text, "ax"
+
 /*
  * Load idle PSW.
  */
@@ -536,7 +543,7 @@
 	jno	.Lmcck_panic
 #if IS_ENABLED(CONFIG_KVM)
 	OUTSIDE	%r9,.Lsie_gmap,.Lsie_done,6f
-	OUTSIDE	%r9,.Lsie_entry,.Lsie_skip,4f
+	OUTSIDE	%r9,.Lsie_entry,.Lsie_leave,4f
 	oi	__LC_CPU_FLAGS+7, _CIF_MCCK_GUEST
 	j	5f
 4:	CHKSTG	.Lmcck_panic
@@ -681,6 +688,7 @@
 .Lthis_cpu:	.short	0
 .Lstosm_tmp:	.byte	0
 	.section .rodata, "a"
+	.balign	8
 #define SYSCALL(esame,emu)	.quad __s390x_ ## esame
 	.globl	sys_call_table
 sys_call_table:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/entry.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/entry.h
@@ -70,5 +70,6 @@
 #define __amode31_data __section(".amode31.data")
 #define __amode31_ref __section(".amode31.refs")
 extern long _start_amode31_refs[], _end_amode31_refs[];
+extern unsigned long __amode31_base;
 
 #endif /* _ENTRY_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/ftrace.c
@@ -80,17 +80,6 @@
 
 #ifdef CONFIG_MODULES
 static char *ftrace_plt;
-
-asm(
-	"	.data\n"
-	"ftrace_plt_template:\n"
-	"	basr	%r1,%r0\n"
-	"	lg	%r1,0f-.(%r1)\n"
-	"	br	%r1\n"
-	"0:	.quad	ftrace_caller\n"
-	"ftrace_plt_template_end:\n"
-	"	.previous\n"
-);
 #endif /* CONFIG_MODULES */
 
 static const char *ftrace_shared_hotpatch_trampoline(const char **end)
@@ -116,7 +105,7 @@
 
 bool ftrace_need_init_nop(void)
 {
-	return ftrace_shared_hotpatch_trampoline(NULL);
+	return true;
 }
 
 int ftrace_init_nop(struct module *mod, struct dyn_ftrace *rec)
@@ -175,28 +164,6 @@
 	return 0;
 }
 
-static void ftrace_generate_nop_insn(struct ftrace_insn *insn)
-{
-	/* brcl 0,0 */
-	insn->opc = 0xc004;
-	insn->disp = 0;
-}
-
-static void ftrace_generate_call_insn(struct ftrace_insn *insn,
-				      unsigned long ip)
-{
-	unsigned long target;
-
-	/* brasl r0,ftrace_caller */
-	target = FTRACE_ADDR;
-#ifdef CONFIG_MODULES
-	if (is_module_addr((void *)ip))
-		target = (unsigned long)ftrace_plt;
-#endif /* CONFIG_MODULES */
-	insn->opc = 0xc005;
-	insn->disp = (target - ip) / 2;
-}
-
 static void brcl_disable(void *brcl)
 {
 	u8 op = 0x04; /* set mask field to zero */
@@ -207,23 +174,7 @@
 int ftrace_make_nop(struct module *mod, struct dyn_ftrace *rec,
 		    unsigned long addr)
 {
-	struct ftrace_insn orig, new, old;
-
-	if (ftrace_shared_hotpatch_trampoline(NULL)) {
-		brcl_disable((void *)rec->ip);
-		return 0;
-	}
-
-	if (copy_from_kernel_nofault(&old, (void *) rec->ip, sizeof(old)))
-		return -EFAULT;
-	/* Replace ftrace call with a nop. */
-	ftrace_generate_call_insn(&orig, rec->ip);
-	ftrace_generate_nop_insn(&new);
-
-	/* Verify that the to be replaced code matches what we expect. */
-	if (memcmp(&orig, &old, sizeof(old)))
-		return -EINVAL;
-	s390_kernel_write((void *) rec->ip, &new, sizeof(new));
+	brcl_disable((void *)rec->ip);
 	return 0;
 }
 
@@ -236,23 +187,7 @@
 
 int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
 {
-	struct ftrace_insn orig, new, old;
-
-	if (ftrace_shared_hotpatch_trampoline(NULL)) {
-		brcl_enable((void *)rec->ip);
-		return 0;
-	}
-
-	if (copy_from_kernel_nofault(&old, (void *) rec->ip, sizeof(old)))
-		return -EFAULT;
-	/* Replace nop with an ftrace call. */
-	ftrace_generate_nop_insn(&orig);
-	ftrace_generate_call_insn(&new, rec->ip);
-
-	/* Verify that the to be replaced code matches what we expect. */
-	if (memcmp(&orig, &old, sizeof(old)))
-		return -EINVAL;
-	s390_kernel_write((void *) rec->ip, &new, sizeof(new));
+	brcl_enable((void *)rec->ip);
 	return 0;
 }
 
@@ -269,10 +204,7 @@
 
 void arch_ftrace_update_code(int command)
 {
-	if (ftrace_shared_hotpatch_trampoline(NULL))
-		ftrace_modify_all_code(command);
-	else
-		ftrace_run_stop_machine(command);
+	ftrace_modify_all_code(command);
 }
 
 static void __ftrace_sync(void *dummy)
@@ -281,10 +213,8 @@
 
 int ftrace_arch_code_modify_post_process(void)
 {
-	if (ftrace_shared_hotpatch_trampoline(NULL)) {
-		/* Send SIGP to the other CPUs, so they see the new code. */
-		smp_call_function(__ftrace_sync, NULL, 1);
-	}
+	/* Send SIGP to the other CPUs, so they see the new code. */
+	smp_call_function(__ftrace_sync, NULL, 1);
 	return 0;
 }
 
@@ -299,10 +229,6 @@
 		panic("cannot allocate ftrace plt\n");
 
 	start = ftrace_shared_hotpatch_trampoline(&end);
-	if (!start) {
-		start = ftrace_plt_template;
-		end = ftrace_plt_template_end;
-	}
 	memcpy(ftrace_plt, start, end - start);
 	set_memory_ro((unsigned long)ftrace_plt, 1);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/idle.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/idle.c
@@ -44,7 +44,7 @@
 	S390_lowcore.last_update_timer = idle->timer_idle_exit;
 }
 
-void arch_cpu_idle(void)
+void noinstr arch_cpu_idle(void)
 {
 	struct s390_idle_data *idle = this_cpu_ptr(&s390_idle);
 	unsigned long idle_time;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/ipl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/ipl.c
@@ -502,6 +502,8 @@
 
 static struct attribute *ipl_unknown_attrs[] = {
 	&sys_ipl_type_attr.attr,
+	&sys_ipl_secure_attr.attr,
+	&sys_ipl_has_secure_attr.attr,
 	NULL,
 };
 
@@ -831,8 +833,8 @@
 		scpdata_len += padding;
 	}
 
-	reipl_block_nvme->hdr.len = IPL_BP_FCP_LEN + scpdata_len;
-	reipl_block_nvme->nvme.len = IPL_BP0_FCP_LEN + scpdata_len;
+	reipl_block_nvme->hdr.len = IPL_BP_NVME_LEN + scpdata_len;
+	reipl_block_nvme->nvme.len = IPL_BP0_NVME_LEN + scpdata_len;
 	reipl_block_nvme->nvme.scp_data_len = scpdata_len;
 
 	return count;
@@ -1601,9 +1603,9 @@
 	}
 	dump_block_nvme->hdr.len = IPL_BP_NVME_LEN;
 	dump_block_nvme->hdr.version = IPL_PARM_BLOCK_VERSION;
-	dump_block_nvme->fcp.len = IPL_BP0_NVME_LEN;
-	dump_block_nvme->fcp.pbt = IPL_PBT_NVME;
-	dump_block_nvme->fcp.opt = IPL_PB0_NVME_OPT_DUMP;
+	dump_block_nvme->nvme.len = IPL_BP0_NVME_LEN;
+	dump_block_nvme->nvme.pbt = IPL_PBT_NVME;
+	dump_block_nvme->nvme.opt = IPL_PB0_NVME_OPT_DUMP;
 	dump_capabilities |= DUMP_TYPE_NVME;
 	return 0;
 }
@@ -1646,8 +1648,8 @@
 
 	csum = (__force unsigned int)
 	       csum_partial(reipl_block_actual, reipl_block_actual->hdr.len, 0);
-	mem_assign_absolute(S390_lowcore.ipib, ipib);
-	mem_assign_absolute(S390_lowcore.ipib_checksum, csum);
+	put_abs_lowcore(ipib, ipib);
+	put_abs_lowcore(ipib_checksum, csum);
 	dump_run(trigger);
 }
 
@@ -2156,7 +2158,7 @@
 
 	buf = vzalloc(report->size);
 	if (!buf)
-		return ERR_PTR(-ENOMEM);
+		goto out;
 	ptr = buf;
 
 	memcpy(ptr, report->ipib, report->ipib->hdr.len);
@@ -2195,6 +2197,7 @@
 	}
 
 	BUG_ON(ptr > buf + report->size);
+out:
 	return buf;
 }
 
@@ -2215,3 +2218,8 @@
 }
 
 #endif
+
+bool ipl_get_secureboot(void)
+{
+	return !!ipl_secure_flag;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/irq.c
@@ -138,7 +138,7 @@
 	struct pt_regs *old_regs = set_irq_regs(regs);
 	int from_idle;
 
-	irq_enter();
+	irq_enter_rcu();
 
 	if (user_mode(regs))
 		update_timer_sys();
@@ -155,7 +155,8 @@
 			do_irq_async(regs, IO_INTERRUPT);
 	} while (MACHINE_IS_LPAR && irq_pending(regs));
 
-	irq_exit();
+	irq_exit_rcu();
+
 	set_irq_regs(old_regs);
 	irqentry_exit(regs, state);
 
@@ -169,7 +170,7 @@
 	struct pt_regs *old_regs = set_irq_regs(regs);
 	int from_idle;
 
-	irq_enter();
+	irq_enter_rcu();
 
 	if (user_mode(regs))
 		update_timer_sys();
@@ -184,7 +185,7 @@
 
 	do_irq_async(regs, EXT_INTERRUPT);
 
-	irq_exit();
+	irq_exit_rcu();
 	set_irq_regs(old_regs);
 	irqentry_exit(regs, state);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/kprobes.c
@@ -7,6 +7,8 @@
  * s390 port, used ppc64 as template. Mike Grundy <grundym@us.ibm.com>
  */
 
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/moduleloader.h>
 #include <linux/kprobes.h>
 #include <linux/ptrace.h>
@@ -231,6 +233,7 @@
 {
 	__this_cpu_write(current_kprobe, kcb->prev_kprobe.kp);
 	kcb->kprobe_status = kcb->prev_kprobe.status;
+	kcb->prev_kprobe.kp = NULL;
 }
 NOKPROBE_SYMBOL(pop_kprobe);
 
@@ -240,7 +243,7 @@
 	ri->fp = NULL;
 
 	/* Replace the return addr with trampoline addr */
-	regs->gprs[14] = (unsigned long) &kretprobe_trampoline;
+	regs->gprs[14] = (unsigned long) &__kretprobe_trampoline;
 }
 NOKPROBE_SYMBOL(arch_prepare_kretprobe);
 
@@ -259,7 +262,7 @@
 		 * is a BUG. The code path resides in the .kprobes.text
 		 * section and is executed with interrupts disabled.
 		 */
-		pr_err("Invalid kprobe detected.\n");
+		pr_err("Failed to recover from reentered kprobes.\n");
 		dump_kprobe(p);
 		BUG();
 	}
@@ -332,8 +335,8 @@
  */
 static void __used kretprobe_trampoline_holder(void)
 {
-	asm volatile(".global kretprobe_trampoline\n"
-		     "kretprobe_trampoline: bcr 0,0\n");
+	asm volatile(".global __kretprobe_trampoline\n"
+		     "__kretprobe_trampoline: bcr 0,0\n");
 }
 
 /*
@@ -341,7 +344,7 @@
  */
 static int trampoline_probe_handler(struct kprobe *p, struct pt_regs *regs)
 {
-	regs->psw.addr = __kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	regs->psw.addr = __kretprobe_trampoline_handler(regs, NULL);
 	/*
 	 * By returning a non-zero value, we are telling
 	 * kprobe_handler() that we don't want the post_handler
@@ -392,12 +395,11 @@
 	if (!p)
 		return 0;
 
+	resume_execution(p, regs);
 	if (kcb->kprobe_status != KPROBE_REENTER && p->post_handler) {
 		kcb->kprobe_status = KPROBE_HIT_SSDONE;
 		p->post_handler(p, regs, 0);
 	}
-
-	resume_execution(p, regs);
 	pop_kprobe(kcb);
 	preempt_enable_no_resched();
 
@@ -507,7 +509,7 @@
 NOKPROBE_SYMBOL(kprobe_exceptions_notify);
 
 static struct kprobe trampoline = {
-	.addr = (kprobe_opcode_t *) &kretprobe_trampoline,
+	.addr = (kprobe_opcode_t *) &__kretprobe_trampoline,
 	.pre_handler = trampoline_probe_handler
 };
 
@@ -516,8 +518,14 @@
 	return register_kprobe(&trampoline);
 }
 
+int __init arch_populate_kprobe_blacklist(void)
+{
+	return kprobe_add_area_blacklist((unsigned long)__irqentry_text_start,
+					 (unsigned long)__irqentry_text_end);
+}
+
 int arch_trampoline_kprobe(struct kprobe *p)
 {
-	return p->addr == (kprobe_opcode_t *) &kretprobe_trampoline;
+	return p->addr == (kprobe_opcode_t *) &__kretprobe_trampoline;
 }
 NOKPROBE_SYMBOL(arch_trampoline_kprobe);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/machine_kexec.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/machine_kexec.c
@@ -227,7 +227,7 @@
 	vmcoreinfo_append_str("SAMODE31=%lx\n", __samode31);
 	vmcoreinfo_append_str("EAMODE31=%lx\n", __eamode31);
 	vmcoreinfo_append_str("KERNELOFFSET=%lx\n", kaslr_offset());
-	mem_assign_absolute(S390_lowcore.vmcore_info, paddr_vmcoreinfo_note());
+	put_abs_lowcore(vmcore_info, paddr_vmcoreinfo_note());
 }
 
 void machine_shutdown(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/machine_kexec_file.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/machine_kexec_file.c
@@ -12,6 +12,7 @@
 #include <linux/kexec.h>
 #include <linux/module_signature.h>
 #include <linux/verification.h>
+#include <linux/vmalloc.h>
 #include <asm/boot_data.h>
 #include <asm/ipl.h>
 #include <asm/setup.h>
@@ -28,6 +29,7 @@
 	const unsigned long marker_len = sizeof(MODULE_SIG_STRING) - 1;
 	struct module_signature *ms;
 	unsigned long sig_len;
+	int ret;
 
 	/* Skip signature verification when not secure IPLed. */
 	if (!ipl_secure_flag)
@@ -62,11 +64,18 @@
 		return -EBADMSG;
 	}
 
-	return verify_pkcs7_signature(kernel, kernel_len,
-				      kernel + kernel_len, sig_len,
-				      VERIFY_USE_PLATFORM_KEYRING,
-				      VERIFYING_MODULE_SIGNATURE,
-				      NULL, NULL);
+	ret = verify_pkcs7_signature(kernel, kernel_len,
+				     kernel + kernel_len, sig_len,
+				     VERIFY_USE_SECONDARY_KEYRING,
+				     VERIFYING_MODULE_SIGNATURE,
+				     NULL, NULL);
+	if (ret == -ENOKEY && IS_ENABLED(CONFIG_INTEGRITY_PLATFORM_KEYRING))
+		ret = verify_pkcs7_signature(kernel, kernel_len,
+					     kernel + kernel_len, sig_len,
+					     VERIFY_USE_PLATFORM_KEYRING,
+					     VERIFYING_MODULE_SIGNATURE,
+					     NULL, NULL);
+	return ret;
 }
 #endif /* CONFIG_KEXEC_SIG */
 
@@ -170,13 +179,12 @@
 	struct kexec_buf buf;
 	unsigned long addr;
 	void *ptr, *end;
+	int ret;
 
 	buf.image = image;
 
 	data->memsz = ALIGN(data->memsz, PAGE_SIZE);
 	buf.mem = data->memsz;
-	if (image->type == KEXEC_TYPE_CRASH)
-		buf.mem += crashk_res.start;
 
 	ptr = (void *)ipl_cert_list_addr;
 	end = ptr + ipl_cert_list_size;
@@ -199,9 +207,13 @@
 		ptr += len;
 	}
 
+	ret = -ENOMEM;
 	buf.buffer = ipl_report_finish(data->report);
+	if (!buf.buffer)
+		goto out;
 	buf.bufsz = data->report->size;
 	buf.memsz = buf.bufsz;
+	image->arch.ipl_buf = buf.buffer;
 
 	data->memsz += buf.memsz;
 
@@ -209,14 +221,21 @@
 		data->kernel_buf + offsetof(struct lowcore, ipl_parmblock_ptr);
 	*lc_ipl_parmblock_ptr = (__u32)buf.mem;
 
-	return kexec_add_buffer(&buf);
+	if (image->type == KEXEC_TYPE_CRASH)
+		buf.mem += crashk_res.start;
+
+	ret = kexec_add_buffer(&buf);
+out:
+	return ret;
 }
 
 void *kexec_file_add_components(struct kimage *image,
 				int (*add_kernel)(struct kimage *image,
 						  struct s390_load_data *data))
 {
+	unsigned long max_command_line_size = LEGACY_COMMAND_LINE_SIZE;
 	struct s390_load_data data = {0};
+	unsigned long minsize;
 	int ret;
 
 	data.report = ipl_report_init(&ipl_block);
@@ -227,10 +246,23 @@
 	if (ret)
 		goto out;
 
-	if (image->cmdline_buf_len >= ARCH_COMMAND_LINE_SIZE) {
-		ret = -EINVAL;
+	ret = -EINVAL;
+	minsize = PARMAREA + offsetof(struct parmarea, command_line);
+	if (image->kernel_buf_len < minsize)
 		goto out;
-	}
+
+	if (data.parm->max_command_line_size)
+		max_command_line_size = data.parm->max_command_line_size;
+
+	if (minsize + max_command_line_size < minsize)
+		goto out;
+
+	if (image->kernel_buf_len < minsize + max_command_line_size)
+		goto out;
+
+	if (image->cmdline_buf_len >= max_command_line_size)
+		goto out;
+
 	memcpy(data.parm->command_line, image->cmdline_buf,
 	       image->cmdline_buf_len);
 
@@ -269,6 +301,7 @@
 {
 	Elf_Rela *relas;
 	int i, r_type;
+	int ret;
 
 	relas = (void *)pi->ehdr + relsec->sh_offset;
 
@@ -303,21 +336,23 @@
 		addr = section->sh_addr + relas[i].r_offset;
 
 		r_type = ELF64_R_TYPE(relas[i].r_info);
-		arch_kexec_do_relocs(r_type, loc, val, addr);
+
+		if (r_type == R_390_PLT32DBL)
+			r_type = R_390_PC32DBL;
+
+		ret = arch_kexec_do_relocs(r_type, loc, val, addr);
+		if (ret) {
+			pr_err("Unknown rela relocation: %d\n", r_type);
+			return -ENOEXEC;
+		}
 	}
 	return 0;
 }
 
-int arch_kexec_kernel_image_probe(struct kimage *image, void *buf,
-				  unsigned long buf_len)
+int arch_kimage_file_post_load_cleanup(struct kimage *image)
 {
-	/* A kernel must be at least large enough to contain head.S. During
-	 * load memory in head.S will be accessed, e.g. to register the next
-	 * command line. If the next kernel were smaller the current kernel
-	 * will panic at load.
-	 */
-	if (buf_len < HEAD_END)
-		return -ENOEXEC;
+	vfree(image->arch.ipl_buf);
+	image->arch.ipl_buf = NULL;
 
-	return kexec_image_probe_default(image, buf, buf_len);
+	return kexec_image_post_load_cleanup_default(image);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/module.c
@@ -33,18 +33,19 @@
 #define DEBUGP(fmt , ...)
 #endif
 
-#define PLT_ENTRY_SIZE 20
+#define PLT_ENTRY_SIZE 22
 
 void *module_alloc(unsigned long size)
 {
+	gfp_t gfp_mask = GFP_KERNEL;
 	void *p;
 
 	if (PAGE_ALIGN(size) > MODULES_LEN)
 		return NULL;
 	p = __vmalloc_node_range(size, MODULE_ALIGN, MODULES_VADDR, MODULES_END,
-				 GFP_KERNEL, PAGE_KERNEL_EXEC, 0, NUMA_NO_NODE,
+				 gfp_mask, PAGE_KERNEL_EXEC, VM_DEFER_KMEMLEAK, NUMA_NO_NODE,
 				 __builtin_return_address(0));
-	if (p && (kasan_module_alloc(p, size) < 0)) {
+	if (p && (kasan_module_alloc(p, size, gfp_mask) < 0)) {
 		vfree(p);
 		return NULL;
 	}
@@ -340,27 +341,26 @@
 	case R_390_PLTOFF32:	/* 32 bit offset from GOT to PLT. */
 	case R_390_PLTOFF64:	/* 16 bit offset from GOT to PLT. */
 		if (info->plt_initialized == 0) {
-			unsigned int insn[5];
-			unsigned int *ip = me->core_layout.base +
-					   me->arch.plt_offset +
-					   info->plt_offset;
-
-			insn[0] = 0x0d10e310;	/* basr 1,0  */
-			insn[1] = 0x100a0004;	/* lg	1,10(1) */
+			unsigned char insn[PLT_ENTRY_SIZE];
+			char *plt_base;
+			char *ip;
+
+			plt_base = me->core_layout.base + me->arch.plt_offset;
+			ip = plt_base + info->plt_offset;
+			*(int *)insn = 0x0d10e310;	/* basr 1,0  */
+			*(int *)&insn[4] = 0x100c0004;	/* lg	1,12(1) */
 			if (IS_ENABLED(CONFIG_EXPOLINE) && !nospec_disable) {
-				unsigned int *ij;
-				ij = me->core_layout.base +
-					me->arch.plt_offset +
-					me->arch.plt_size - PLT_ENTRY_SIZE;
-				insn[2] = 0xa7f40000 +	/* j __jump_r1 */
-					(unsigned int)(u16)
-					(((unsigned long) ij - 8 -
-					  (unsigned long) ip) / 2);
+				char *jump_r1;
+
+				jump_r1 = plt_base + me->arch.plt_size -
+					PLT_ENTRY_SIZE;
+				/* brcl	0xf,__jump_r1 */
+				*(short *)&insn[8] = 0xc0f4;
+				*(int *)&insn[10] = (jump_r1 - (ip + 8)) / 2;
 			} else {
-				insn[2] = 0x07f10000;	/* br %r1 */
+				*(int *)&insn[8] = 0x07f10000;	/* br %r1 */
 			}
-			insn[3] = (unsigned int) (val >> 32);
-			insn[4] = (unsigned int) val;
+			*(long *)&insn[14] = val;
 
 			write(ip, insn, sizeof(insn));
 			info->plt_initialized = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/nmi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/nmi.c
@@ -62,7 +62,7 @@
  * The structure is required for machine check happening early in
  * the boot process.
  */
-static struct mcesa boot_mcesa __initdata __aligned(MCESA_MAX_SIZE);
+static struct mcesa boot_mcesa __aligned(MCESA_MAX_SIZE);
 
 void __init nmi_alloc_boot_cpu(struct lowcore *lc)
 {
@@ -175,7 +175,7 @@
 		       "malfunction (code 0x%016lx).\n", mcck.mcck_code);
 		printk(KERN_EMERG "mcck: task: %s, pid: %d.\n",
 		       current->comm, current->pid);
-		do_exit(SIGSEGV);
+		make_task_dead(SIGSEGV);
 	}
 }
 
@@ -273,7 +273,14 @@
 		/* Validate vector registers */
 		union ctlreg0 cr0;
 
-		if (!mci.vr) {
+		/*
+		 * The vector validity must only be checked if not running a
+		 * KVM guest. For KVM guests the machine check is forwarded by
+		 * KVM and it is the responsibility of the guest to take
+		 * appropriate actions. The host vector or FPU values have been
+		 * saved by KVM and will be restored by KVM.
+		 */
+		if (!mci.vr && !test_cpu_flag(CIF_MCCK_GUEST)) {
 			/*
 			 * Vector registers can't be restored. If the kernel
 			 * currently uses vector registers the system is
@@ -316,11 +323,21 @@
 	if (cr2.gse) {
 		if (!mci.gs) {
 			/*
-			 * Guarded storage register can't be restored and
-			 * the current processes uses guarded storage.
-			 * It has to be terminated.
+			 * 2 cases:
+			 * - machine check in kernel or userspace
+			 * - machine check while running SIE (KVM guest)
+			 * For kernel or userspace the userspace values of
+			 * guarded storage control can not be recreated, the
+			 * process must be terminated.
+			 * For SIE the guest values of guarded storage can not
+			 * be recreated. This is either due to a bug or due to
+			 * GS being disabled in the guest. The guest will be
+			 * notified by KVM code and the guests machine check
+			 * handling must take care of this.  The host values
+			 * are saved by KVM and are not affected.
 			 */
-			kill_task = 1;
+			if (!test_cpu_flag(CIF_MCCK_GUEST))
+				kill_task = 1;
 		} else {
 			load_gs_cb((struct gs_cb *)mcesa->guarded_storage_save_area);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/nospec-branch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/nospec-branch.c
@@ -105,6 +105,7 @@
 	s32 *epo;
 
 	/* Second part of the instruction replace is always a nop */
+	memcpy(insnbuf + 2, branch, sizeof(branch));
 	for (epo = start; epo < end; epo++) {
 		instr = (u8 *) epo + *epo;
 		if (instr[0] == 0xc0 && (instr[1] & 0x0f) == 0x04)
@@ -125,34 +126,18 @@
 			br = thunk + (*(int *)(thunk + 2)) * 2;
 		else
 			continue;
-		/* Check for unconditional branch 0x07f? or 0x47f???? */
-		if ((br[0] & 0xbf) != 0x07 || (br[1] & 0xf0) != 0xf0)
+		if (br[0] != 0x07 || (br[1] & 0xf0) != 0xf0)
 			continue;
-
-		memcpy(insnbuf + 2, branch, sizeof(branch));
 		switch (type) {
 		case BRCL_EXPOLINE:
+			/* brcl to thunk, replace with br + nop */
 			insnbuf[0] = br[0];
 			insnbuf[1] = (instr[1] & 0xf0) | (br[1] & 0x0f);
-			if (br[0] == 0x47) {
-				/* brcl to b, replace with bc + nopr */
-				insnbuf[2] = br[2];
-				insnbuf[3] = br[3];
-			} else {
-				/* brcl to br, replace with bcr + nop */
-			}
 			break;
 		case BRASL_EXPOLINE:
+			/* brasl to thunk, replace with basr + nop */
+			insnbuf[0] = 0x0d;
 			insnbuf[1] = (instr[1] & 0xf0) | (br[1] & 0x0f);
-			if (br[0] == 0x47) {
-				/* brasl to b, replace with bas + nopr */
-				insnbuf[0] = 0x4d;
-				insnbuf[2] = br[2];
-				insnbuf[3] = br[3];
-			} else {
-				/* brasl to br, replace with basr + nop */
-				insnbuf[0] = 0x0d;
-			}
 			break;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/os_info.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/os_info.c
@@ -15,6 +15,7 @@
 #include <asm/checksum.h>
 #include <asm/lowcore.h>
 #include <asm/os_info.h>
+#include <asm/asm-offsets.h>
 
 /*
  * OS info structure has to be page aligned
@@ -45,7 +46,7 @@
  */
 void os_info_entry_add(int nr, void *ptr, u64 size)
 {
-	os_info.entry[nr].addr = (u64)(unsigned long)ptr;
+	os_info.entry[nr].addr = __pa(ptr);
 	os_info.entry[nr].size = size;
 	os_info.entry[nr].csum = (__force u32)csum_partial(ptr, size, 0);
 	os_info.csum = os_info_csum(&os_info);
@@ -62,7 +63,7 @@
 	os_info.version_minor = OS_INFO_VERSION_MINOR;
 	os_info.magic = OS_INFO_MAGIC;
 	os_info.csum = os_info_csum(&os_info);
-	mem_assign_absolute(S390_lowcore.os_info, (unsigned long) ptr);
+	put_abs_lowcore(os_info, __pa(ptr));
 }
 
 #ifdef CONFIG_CRASH_DUMP
@@ -90,7 +91,7 @@
 		goto fail;
 	}
 	buf_align = PTR_ALIGN(buf, align);
-	if (copy_oldmem_kernel(buf_align, (void *) addr, size)) {
+	if (copy_oldmem_kernel(buf_align, addr, size)) {
 		msg = "copy failed";
 		goto fail_free;
 	}
@@ -123,15 +124,14 @@
 		return;
 	if (!oldmem_data.start)
 		goto fail;
-	if (copy_oldmem_kernel(&addr, &S390_lowcore.os_info, sizeof(addr)))
+	if (copy_oldmem_kernel(&addr, __LC_OS_INFO, sizeof(addr)))
 		goto fail;
 	if (addr == 0 || addr % PAGE_SIZE)
 		goto fail;
 	os_info_old = kzalloc(sizeof(*os_info_old), GFP_KERNEL);
 	if (!os_info_old)
 		goto fail;
-	if (copy_oldmem_kernel(os_info_old, (void *) addr,
-			       sizeof(*os_info_old)))
+	if (copy_oldmem_kernel(os_info_old, addr, sizeof(*os_info_old)))
 		goto fail_free;
 	if (os_info_old->magic != OS_INFO_MAGIC)
 		goto fail_free;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/perf_cpum_cf.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/perf_cpum_cf.c
@@ -516,6 +516,26 @@
 	return err;
 }
 
+/* Events CPU_CYLCES and INSTRUCTIONS can be submitted with two different
+ * attribute::type values:
+ * - PERF_TYPE_HARDWARE:
+ * - pmu->type:
+ * Handle both type of invocations identical. They address the same hardware.
+ * The result is different when event modifiers exclude_kernel and/or
+ * exclude_user are also set.
+ */
+static int cpumf_pmu_event_type(struct perf_event *event)
+{
+	u64 ev = event->attr.config;
+
+	if (cpumf_generic_events_basic[PERF_COUNT_HW_CPU_CYCLES] == ev ||
+	    cpumf_generic_events_basic[PERF_COUNT_HW_INSTRUCTIONS] == ev ||
+	    cpumf_generic_events_user[PERF_COUNT_HW_CPU_CYCLES] == ev ||
+	    cpumf_generic_events_user[PERF_COUNT_HW_INSTRUCTIONS] == ev)
+		return PERF_TYPE_HARDWARE;
+	return PERF_TYPE_RAW;
+}
+
 static int cpumf_pmu_event_init(struct perf_event *event)
 {
 	unsigned int type = event->attr.type;
@@ -525,7 +545,7 @@
 		err = __hw_perf_event_init(event, type);
 	else if (event->pmu->type == type)
 		/* Registered as unknown PMU */
-		err = __hw_perf_event_init(event, PERF_TYPE_RAW);
+		err = __hw_perf_event_init(event, cpumf_pmu_event_type(event));
 	else
 		return -ENOENT;
 
@@ -687,8 +707,10 @@
 						      false);
 			if (cfdiag_diffctr(cpuhw, event->hw.config_base))
 				cfdiag_push_sample(event, cpuhw);
-		} else
+		} else if (cpuhw->flags & PMU_F_RESERVED) {
+			/* Only update when PMU not hotplugged off */
 			hw_perf_event_update(event);
+		}
 		hwc->state |= PERF_HES_UPTODATE;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/perf_cpum_cf_common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/perf_cpum_cf_common.c
@@ -178,7 +178,7 @@
 	case CPUMF_CTR_SET_CRYPTO:
 		if (info->csvn >= 1 && info->csvn <= 5)
 			ctrset_size = 16;
-		else if (info->csvn == 6)
+		else if (info->csvn >= 6)
 			ctrset_size = 20;
 		break;
 	case CPUMF_CTR_SET_EXT:
@@ -188,7 +188,7 @@
 			ctrset_size = 48;
 		else if (info->csvn >= 3 && info->csvn <= 5)
 			ctrset_size = 128;
-		else if (info->csvn == 6)
+		else if (info->csvn == 6 || info->csvn == 7)
 			ctrset_size = 160;
 		break;
 	case CPUMF_CTR_SET_MT_DIAG:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/perf_cpum_cf_events.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/perf_cpum_cf_events.c
@@ -295,6 +295,76 @@
 CPUMF_EVENT_ATTR(cf_z15, DFLT_CCFINISH, 0x00109);
 CPUMF_EVENT_ATTR(cf_z15, MT_DIAG_CYCLES_ONE_THR_ACTIVE, 0x01c0);
 CPUMF_EVENT_ATTR(cf_z15, MT_DIAG_CYCLES_TWO_THR_ACTIVE, 0x01c1);
+CPUMF_EVENT_ATTR(cf_z16, L1D_RO_EXCL_WRITES, 0x0080);
+CPUMF_EVENT_ATTR(cf_z16, DTLB2_WRITES, 0x0081);
+CPUMF_EVENT_ATTR(cf_z16, DTLB2_MISSES, 0x0082);
+CPUMF_EVENT_ATTR(cf_z16, CRSTE_1MB_WRITES, 0x0083);
+CPUMF_EVENT_ATTR(cf_z16, DTLB2_GPAGE_WRITES, 0x0084);
+CPUMF_EVENT_ATTR(cf_z16, ITLB2_WRITES, 0x0086);
+CPUMF_EVENT_ATTR(cf_z16, ITLB2_MISSES, 0x0087);
+CPUMF_EVENT_ATTR(cf_z16, TLB2_PTE_WRITES, 0x0089);
+CPUMF_EVENT_ATTR(cf_z16, TLB2_CRSTE_WRITES, 0x008a);
+CPUMF_EVENT_ATTR(cf_z16, TLB2_ENGINES_BUSY, 0x008b);
+CPUMF_EVENT_ATTR(cf_z16, TX_C_TEND, 0x008c);
+CPUMF_EVENT_ATTR(cf_z16, TX_NC_TEND, 0x008d);
+CPUMF_EVENT_ATTR(cf_z16, L1C_TLB2_MISSES, 0x008f);
+CPUMF_EVENT_ATTR(cf_z16, DCW_REQ, 0x0091);
+CPUMF_EVENT_ATTR(cf_z16, DCW_REQ_IV, 0x0092);
+CPUMF_EVENT_ATTR(cf_z16, DCW_REQ_CHIP_HIT, 0x0093);
+CPUMF_EVENT_ATTR(cf_z16, DCW_REQ_DRAWER_HIT, 0x0094);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_CHIP, 0x0095);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_CHIP_IV, 0x0096);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_CHIP_CHIP_HIT, 0x0097);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_CHIP_DRAWER_HIT, 0x0098);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_MODULE, 0x0099);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_DRAWER, 0x009a);
+CPUMF_EVENT_ATTR(cf_z16, DCW_OFF_DRAWER, 0x009b);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_CHIP_MEMORY, 0x009c);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_MODULE_MEMORY, 0x009d);
+CPUMF_EVENT_ATTR(cf_z16, DCW_ON_DRAWER_MEMORY, 0x009e);
+CPUMF_EVENT_ATTR(cf_z16, DCW_OFF_DRAWER_MEMORY, 0x009f);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_ON_MODULE_IV, 0x00a0);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_ON_MODULE_CHIP_HIT, 0x00a1);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_ON_MODULE_DRAWER_HIT, 0x00a2);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_ON_DRAWER_IV, 0x00a3);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_ON_DRAWER_CHIP_HIT, 0x00a4);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_ON_DRAWER_DRAWER_HIT, 0x00a5);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_OFF_DRAWER_IV, 0x00a6);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_OFF_DRAWER_CHIP_HIT, 0x00a7);
+CPUMF_EVENT_ATTR(cf_z16, IDCW_OFF_DRAWER_DRAWER_HIT, 0x00a8);
+CPUMF_EVENT_ATTR(cf_z16, ICW_REQ, 0x00a9);
+CPUMF_EVENT_ATTR(cf_z16, ICW_REQ_IV, 0x00aa);
+CPUMF_EVENT_ATTR(cf_z16, ICW_REQ_CHIP_HIT, 0x00ab);
+CPUMF_EVENT_ATTR(cf_z16, ICW_REQ_DRAWER_HIT, 0x00ac);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_CHIP, 0x00ad);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_CHIP_IV, 0x00ae);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_CHIP_CHIP_HIT, 0x00af);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_CHIP_DRAWER_HIT, 0x00b0);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_MODULE, 0x00b1);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_DRAWER, 0x00b2);
+CPUMF_EVENT_ATTR(cf_z16, ICW_OFF_DRAWER, 0x00b3);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_CHIP_MEMORY, 0x00b4);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_MODULE_MEMORY, 0x00b5);
+CPUMF_EVENT_ATTR(cf_z16, ICW_ON_DRAWER_MEMORY, 0x00b6);
+CPUMF_EVENT_ATTR(cf_z16, ICW_OFF_DRAWER_MEMORY, 0x00b7);
+CPUMF_EVENT_ATTR(cf_z16, BCD_DFP_EXECUTION_SLOTS, 0x00e0);
+CPUMF_EVENT_ATTR(cf_z16, VX_BCD_EXECUTION_SLOTS, 0x00e1);
+CPUMF_EVENT_ATTR(cf_z16, DECIMAL_INSTRUCTIONS, 0x00e2);
+CPUMF_EVENT_ATTR(cf_z16, LAST_HOST_TRANSLATIONS, 0x00e8);
+CPUMF_EVENT_ATTR(cf_z16, TX_NC_TABORT, 0x00f4);
+CPUMF_EVENT_ATTR(cf_z16, TX_C_TABORT_NO_SPECIAL, 0x00f5);
+CPUMF_EVENT_ATTR(cf_z16, TX_C_TABORT_SPECIAL, 0x00f6);
+CPUMF_EVENT_ATTR(cf_z16, DFLT_ACCESS, 0x00f8);
+CPUMF_EVENT_ATTR(cf_z16, DFLT_CYCLES, 0x00fd);
+CPUMF_EVENT_ATTR(cf_z16, SORTL, 0x0100);
+CPUMF_EVENT_ATTR(cf_z16, DFLT_CC, 0x0109);
+CPUMF_EVENT_ATTR(cf_z16, DFLT_CCFINISH, 0x010a);
+CPUMF_EVENT_ATTR(cf_z16, NNPA_INVOCATIONS, 0x010b);
+CPUMF_EVENT_ATTR(cf_z16, NNPA_COMPLETIONS, 0x010c);
+CPUMF_EVENT_ATTR(cf_z16, NNPA_WAIT_LOCK, 0x010d);
+CPUMF_EVENT_ATTR(cf_z16, NNPA_HOLD_LOCK, 0x010e);
+CPUMF_EVENT_ATTR(cf_z16, MT_DIAG_CYCLES_ONE_THR_ACTIVE, 0x01c0);
+CPUMF_EVENT_ATTR(cf_z16, MT_DIAG_CYCLES_TWO_THR_ACTIVE, 0x01c1);
 
 static struct attribute *cpumcf_fvn1_pmu_event_attr[] __initdata = {
 	CPUMF_EVENT_PTR(cf_fvn1, CPU_CYCLES),
@@ -344,7 +414,7 @@
 	NULL,
 };
 
-static struct attribute *cpumcf_svn_6_pmu_event_attr[] __initdata = {
+static struct attribute *cpumcf_svn_67_pmu_event_attr[] __initdata = {
 	CPUMF_EVENT_PTR(cf_svn_12345, PRNG_FUNCTIONS),
 	CPUMF_EVENT_PTR(cf_svn_12345, PRNG_CYCLES),
 	CPUMF_EVENT_PTR(cf_svn_12345, PRNG_BLOCKED_FUNCTIONS),
@@ -635,6 +705,80 @@
 	NULL,
 };
 
+static struct attribute *cpumcf_z16_pmu_event_attr[] __initdata = {
+	CPUMF_EVENT_PTR(cf_z16, L1D_RO_EXCL_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, DTLB2_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, DTLB2_MISSES),
+	CPUMF_EVENT_PTR(cf_z16, CRSTE_1MB_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, DTLB2_GPAGE_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, ITLB2_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, ITLB2_MISSES),
+	CPUMF_EVENT_PTR(cf_z16, TLB2_PTE_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, TLB2_CRSTE_WRITES),
+	CPUMF_EVENT_PTR(cf_z16, TLB2_ENGINES_BUSY),
+	CPUMF_EVENT_PTR(cf_z16, TX_C_TEND),
+	CPUMF_EVENT_PTR(cf_z16, TX_NC_TEND),
+	CPUMF_EVENT_PTR(cf_z16, L1C_TLB2_MISSES),
+	CPUMF_EVENT_PTR(cf_z16, DCW_REQ),
+	CPUMF_EVENT_PTR(cf_z16, DCW_REQ_IV),
+	CPUMF_EVENT_PTR(cf_z16, DCW_REQ_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, DCW_REQ_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_CHIP),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_CHIP_IV),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_CHIP_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_CHIP_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_MODULE),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_DRAWER),
+	CPUMF_EVENT_PTR(cf_z16, DCW_OFF_DRAWER),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_CHIP_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_MODULE_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, DCW_ON_DRAWER_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, DCW_OFF_DRAWER_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_ON_MODULE_IV),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_ON_MODULE_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_ON_MODULE_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_ON_DRAWER_IV),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_ON_DRAWER_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_ON_DRAWER_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_OFF_DRAWER_IV),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_OFF_DRAWER_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, IDCW_OFF_DRAWER_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, ICW_REQ),
+	CPUMF_EVENT_PTR(cf_z16, ICW_REQ_IV),
+	CPUMF_EVENT_PTR(cf_z16, ICW_REQ_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, ICW_REQ_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_CHIP),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_CHIP_IV),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_CHIP_CHIP_HIT),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_CHIP_DRAWER_HIT),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_MODULE),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_DRAWER),
+	CPUMF_EVENT_PTR(cf_z16, ICW_OFF_DRAWER),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_CHIP_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_MODULE_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, ICW_ON_DRAWER_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, ICW_OFF_DRAWER_MEMORY),
+	CPUMF_EVENT_PTR(cf_z16, BCD_DFP_EXECUTION_SLOTS),
+	CPUMF_EVENT_PTR(cf_z16, VX_BCD_EXECUTION_SLOTS),
+	CPUMF_EVENT_PTR(cf_z16, DECIMAL_INSTRUCTIONS),
+	CPUMF_EVENT_PTR(cf_z16, LAST_HOST_TRANSLATIONS),
+	CPUMF_EVENT_PTR(cf_z16, TX_NC_TABORT),
+	CPUMF_EVENT_PTR(cf_z16, TX_C_TABORT_NO_SPECIAL),
+	CPUMF_EVENT_PTR(cf_z16, TX_C_TABORT_SPECIAL),
+	CPUMF_EVENT_PTR(cf_z16, DFLT_ACCESS),
+	CPUMF_EVENT_PTR(cf_z16, DFLT_CYCLES),
+	CPUMF_EVENT_PTR(cf_z16, SORTL),
+	CPUMF_EVENT_PTR(cf_z16, DFLT_CC),
+	CPUMF_EVENT_PTR(cf_z16, DFLT_CCFINISH),
+	CPUMF_EVENT_PTR(cf_z16, NNPA_INVOCATIONS),
+	CPUMF_EVENT_PTR(cf_z16, NNPA_COMPLETIONS),
+	CPUMF_EVENT_PTR(cf_z16, NNPA_WAIT_LOCK),
+	CPUMF_EVENT_PTR(cf_z16, NNPA_HOLD_LOCK),
+	CPUMF_EVENT_PTR(cf_z16, MT_DIAG_CYCLES_ONE_THR_ACTIVE),
+	CPUMF_EVENT_PTR(cf_z16, MT_DIAG_CYCLES_TWO_THR_ACTIVE),
+	NULL,
+};
+
 /* END: CPUM_CF COUNTER DEFINITIONS ===================================== */
 
 static struct attribute_group cpumcf_pmu_events_group = {
@@ -711,16 +855,11 @@
 	}
 
 	/* Determine version specific crypto set */
-	switch (ci.csvn) {
-	case 1 ... 5:
+	csvn = none;
+	if (ci.csvn >= 1 && ci.csvn <= 5)
 		csvn = cpumcf_svn_12345_pmu_event_attr;
-		break;
-	case 6:
-		csvn = cpumcf_svn_6_pmu_event_attr;
-		break;
-	default:
-		csvn = none;
-	}
+	else if (ci.csvn >= 6)
+		csvn = cpumcf_svn_67_pmu_event_attr;
 
 	/* Determine model-specific counter set(s) */
 	get_cpu_id(&cpu_id);
@@ -749,6 +888,10 @@
 	case 0x8562:
 		model = cpumcf_z15_pmu_event_attr;
 		break;
+	case 0x3931:
+	case 0x3932:
+		model = cpumcf_z16_pmu_event_attr;
+		break;
 	default:
 		model = none;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/perf_cpum_sf.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/perf_cpum_sf.c
@@ -163,14 +163,15 @@
 
 static int alloc_sample_data_block(unsigned long *sdbt, gfp_t gfp_flags)
 {
-	unsigned long sdb, *trailer;
+	struct hws_trailer_entry *te;
+	unsigned long sdb;
 
 	/* Allocate and initialize sample-data-block */
 	sdb = get_zeroed_page(gfp_flags);
 	if (!sdb)
 		return -ENOMEM;
-	trailer = trailer_entry_ptr(sdb);
-	*trailer = SDB_TE_ALERT_REQ_MASK;
+	te = (struct hws_trailer_entry *)trailer_entry_ptr(sdb);
+	te->header.a = 1;
 
 	/* Link SDB into the sample-data-block-table */
 	*sdbt = sdb;
@@ -1179,7 +1180,7 @@
 	sample = (struct hws_basic_entry *) *sdbt;
 	while ((unsigned long *) sample < (unsigned long *) te) {
 		/* Check for an empty sample */
-		if (!sample->def)
+		if (!sample->def || sample->LS)
 			break;
 
 		/* Update perf event period */
@@ -1206,7 +1207,7 @@
 					    "%s: Found unknown"
 					    " sampling data entry: te->f %i"
 					    " basic.def %#4x (%p)\n", __func__,
-					    te->f, sample->def, sample);
+					    te->header.f, sample->def, sample);
 			/* Sample slot is not yet written or other record.
 			 *
 			 * This condition can occur if the buffer was reused
@@ -1217,7 +1218,7 @@
 			 * that are not full.  Stop processing if the first
 			 * invalid format was detected.
 			 */
-			if (!te->f)
+			if (!te->header.f)
 				break;
 		}
 
@@ -1227,6 +1228,16 @@
 	}
 }
 
+static inline __uint128_t __cdsg(__uint128_t *ptr, __uint128_t old, __uint128_t new)
+{
+	asm volatile(
+		"	cdsg	%[old],%[new],%[ptr]\n"
+		: [old] "+d" (old), [ptr] "+QS" (*ptr)
+		: [new] "d" (new)
+		: "memory", "cc");
+	return old;
+}
+
 /* hw_perf_event_update() - Process sampling buffer
  * @event:	The perf event
  * @flush_all:	Flag to also flush partially filled sample-data-blocks
@@ -1243,10 +1254,11 @@
  */
 static void hw_perf_event_update(struct perf_event *event, int flush_all)
 {
+	unsigned long long event_overflow, sampl_overflow, num_sdb;
+	union hws_trailer_header old, prev, new;
 	struct hw_perf_event *hwc = &event->hw;
 	struct hws_trailer_entry *te;
 	unsigned long *sdbt;
-	unsigned long long event_overflow, sampl_overflow, num_sdb, te_flags;
 	int done;
 
 	/*
@@ -1266,25 +1278,25 @@
 		te = (struct hws_trailer_entry *) trailer_entry_ptr(*sdbt);
 
 		/* Leave loop if no more work to do (block full indicator) */
-		if (!te->f) {
+		if (!te->header.f) {
 			done = 1;
 			if (!flush_all)
 				break;
 		}
 
 		/* Check the sample overflow count */
-		if (te->overflow)
+		if (te->header.overflow)
 			/* Account sample overflows and, if a particular limit
 			 * is reached, extend the sampling buffer.
 			 * For details, see sfb_account_overflows().
 			 */
-			sampl_overflow += te->overflow;
+			sampl_overflow += te->header.overflow;
 
 		/* Timestamps are valid for full sample-data-blocks only */
 		debug_sprintf_event(sfdbg, 6, "%s: sdbt %#lx "
 				    "overflow %llu timestamp %#llx\n",
-				    __func__, (unsigned long)sdbt, te->overflow,
-				    (te->f) ? trailer_timestamp(te) : 0ULL);
+				    __func__, (unsigned long)sdbt, te->header.overflow,
+				    (te->header.f) ? trailer_timestamp(te) : 0ULL);
 
 		/* Collect all samples from a single sample-data-block and
 		 * flag if an (perf) event overflow happened.  If so, the PMU
@@ -1294,12 +1306,16 @@
 		num_sdb++;
 
 		/* Reset trailer (using compare-double-and-swap) */
+		/* READ_ONCE() 16 byte header */
+		prev.val = __cdsg(&te->header.val, 0, 0);
 		do {
-			te_flags = te->flags & ~SDB_TE_BUFFER_FULL_MASK;
-			te_flags |= SDB_TE_ALERT_REQ_MASK;
-		} while (!cmpxchg_double(&te->flags, &te->overflow,
-					 te->flags, te->overflow,
-					 te_flags, 0ULL));
+			old.val = prev.val;
+			new.val = prev.val;
+			new.f = 0;
+			new.a = 1;
+			new.overflow = 0;
+			prev.val = __cdsg(&te->header.val, old.val, new.val);
+		} while (prev.val != old.val);
 
 		/* Advance to next sample-data-block */
 		sdbt++;
@@ -1384,7 +1400,7 @@
 	range_scan = AUX_SDB_NUM_ALERT(aux);
 	for (i = 0, idx = aux->head; i < range_scan; i++, idx++) {
 		te = aux_sdb_trailer(aux, idx);
-		if (!(te->flags & SDB_TE_BUFFER_FULL_MASK))
+		if (!te->header.f)
 			break;
 	}
 	/* i is num of SDBs which are full */
@@ -1392,7 +1408,7 @@
 
 	/* Remove alert indicators in the buffer */
 	te = aux_sdb_trailer(aux, aux->alert_mark);
-	te->flags &= ~SDB_TE_ALERT_REQ_MASK;
+	te->header.a = 0;
 
 	debug_sprintf_event(sfdbg, 6, "%s: SDBs %ld range %ld head %ld\n",
 			    __func__, i, range_scan, aux->head);
@@ -1416,7 +1432,7 @@
 	unsigned long head, base, offset;
 	struct hws_trailer_entry *te;
 
-	if (WARN_ON_ONCE(handle->head & ~PAGE_MASK))
+	if (handle->head & ~PAGE_MASK)
 		return -EINVAL;
 
 	aux->head = handle->head >> PAGE_SHIFT;
@@ -1437,9 +1453,9 @@
 		idx = aux->empty_mark + 1;
 		for (i = 0; i < range_scan; i++, idx++) {
 			te = aux_sdb_trailer(aux, idx);
-			te->flags &= ~(SDB_TE_BUFFER_FULL_MASK |
-				       SDB_TE_ALERT_REQ_MASK);
-			te->overflow = 0;
+			te->header.f = 0;
+			te->header.a = 0;
+			te->header.overflow = 0;
 		}
 		/* Save the position of empty SDBs */
 		aux->empty_mark = aux->head + range - 1;
@@ -1448,7 +1464,7 @@
 	/* Set alert indicator */
 	aux->alert_mark = aux->head + range/2 - 1;
 	te = aux_sdb_trailer(aux, aux->alert_mark);
-	te->flags = te->flags | SDB_TE_ALERT_REQ_MASK;
+	te->header.a = 1;
 
 	/* Reset hardware buffer head */
 	head = AUX_SDB_INDEX(aux, aux->head);
@@ -1475,14 +1491,17 @@
 static bool aux_set_alert(struct aux_buffer *aux, unsigned long alert_index,
 			  unsigned long long *overflow)
 {
-	unsigned long long orig_overflow, orig_flags, new_flags;
+	union hws_trailer_header old, prev, new;
 	struct hws_trailer_entry *te;
 
 	te = aux_sdb_trailer(aux, alert_index);
+	/* READ_ONCE() 16 byte header */
+	prev.val = __cdsg(&te->header.val, 0, 0);
 	do {
-		orig_flags = te->flags;
-		*overflow = orig_overflow = te->overflow;
-		if (orig_flags & SDB_TE_BUFFER_FULL_MASK) {
+		old.val = prev.val;
+		new.val = prev.val;
+		*overflow = old.overflow;
+		if (old.f) {
 			/*
 			 * SDB is already set by hardware.
 			 * Abort and try to set somewhere
@@ -1490,10 +1509,10 @@
 			 */
 			return false;
 		}
-		new_flags = orig_flags | SDB_TE_ALERT_REQ_MASK;
-	} while (!cmpxchg_double(&te->flags, &te->overflow,
-				 orig_flags, orig_overflow,
-				 new_flags, 0ULL));
+		new.a = 1;
+		new.overflow = 0;
+		prev.val = __cdsg(&te->header.val, old.val, new.val);
+	} while (prev.val != old.val);
 	return true;
 }
 
@@ -1522,8 +1541,9 @@
 static bool aux_reset_buffer(struct aux_buffer *aux, unsigned long range,
 			     unsigned long long *overflow)
 {
-	unsigned long long orig_overflow, orig_flags, new_flags;
 	unsigned long i, range_scan, idx, idx_old;
+	union hws_trailer_header old, prev, new;
+	unsigned long long orig_overflow;
 	struct hws_trailer_entry *te;
 
 	debug_sprintf_event(sfdbg, 6, "%s: range %ld head %ld alert %ld "
@@ -1554,17 +1574,20 @@
 	idx_old = idx = aux->empty_mark + 1;
 	for (i = 0; i < range_scan; i++, idx++) {
 		te = aux_sdb_trailer(aux, idx);
+		/* READ_ONCE() 16 byte header */
+		prev.val = __cdsg(&te->header.val, 0, 0);
 		do {
-			orig_flags = te->flags;
-			orig_overflow = te->overflow;
-			new_flags = orig_flags & ~SDB_TE_BUFFER_FULL_MASK;
+			old.val = prev.val;
+			new.val = prev.val;
+			orig_overflow = old.overflow;
+			new.f = 0;
+			new.overflow = 0;
 			if (idx == aux->alert_mark)
-				new_flags |= SDB_TE_ALERT_REQ_MASK;
+				new.a = 1;
 			else
-				new_flags &= ~SDB_TE_ALERT_REQ_MASK;
-		} while (!cmpxchg_double(&te->flags, &te->overflow,
-					 orig_flags, orig_overflow,
-					 new_flags, 0ULL));
+				new.a = 0;
+			prev.val = __cdsg(&te->header.val, old.val, new.val);
+		} while (prev.val != old.val);
 		*overflow += orig_overflow;
 	}
 
@@ -1590,7 +1613,7 @@
 	unsigned long num_sdb;
 
 	aux = perf_get_aux(handle);
-	if (WARN_ON_ONCE(!aux))
+	if (!aux)
 		return;
 
 	/* Inform user space new data arrived */
@@ -1612,7 +1635,7 @@
 					    __func__);
 			break;
 		}
-		if (WARN_ON_ONCE(!aux))
+		if (!aux)
 			return;
 
 		/* Update head and alert_mark to new position */
@@ -1847,12 +1870,8 @@
 {
 	struct cpu_hw_sf *cpuhw = this_cpu_ptr(&cpu_hw_sf);
 
-	if (WARN_ON_ONCE(!(event->hw.state & PERF_HES_STOPPED)))
+	if (!(event->hw.state & PERF_HES_STOPPED))
 		return;
-
-	if (flags & PERF_EF_RELOAD)
-		WARN_ON_ONCE(!(event->hw.state & PERF_HES_UPTODATE));
-
 	perf_pmu_disable(event->pmu);
 	event->hw.state = 0;
 	cpuhw->lsctl.cs = 1;
@@ -1877,7 +1896,9 @@
 	event->hw.state |= PERF_HES_STOPPED;
 
 	if ((flags & PERF_EF_UPDATE) && !(event->hw.state & PERF_HES_UPTODATE)) {
-		hw_perf_event_update(event, 1);
+		/* CPU hotplug off removes SDBs. No samples to extract. */
+		if (cpuhw->flags & PMU_F_RESERVED)
+			hw_perf_event_update(event, 1);
 		event->hw.state |= PERF_HES_UPTODATE;
 	}
 	perf_pmu_enable(event->pmu);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/perf_event.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/perf_event.c
@@ -30,7 +30,7 @@
 	if (!stack)
 		return NULL;
 
-	return (struct kvm_s390_sie_block *) stack->empty1[0];
+	return (struct kvm_s390_sie_block *)stack->empty1[1];
 }
 
 static bool is_in_guest(struct pt_regs *regs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/process.c
@@ -91,6 +91,18 @@
 
 	memcpy(dst, src, arch_task_struct_size);
 	dst->thread.fpu.regs = dst->thread.fpu.fprs;
+
+	/*
+	 * Don't transfer over the runtime instrumentation or the guarded
+	 * storage control block pointers. These fields are cleared here instead
+	 * of in copy_thread() to avoid premature freeing of associated memory
+	 * on fork() failure. Wait to clear the RI flag because ->stack still
+	 * refers to the source thread.
+	 */
+	dst->thread.ri_cb = NULL;
+	dst->thread.gs_cb = NULL;
+	dst->thread.gs_bc_cb = NULL;
+
 	return 0;
 }
 
@@ -149,13 +161,11 @@
 	frame->childregs.flags = 0;
 	if (new_stackp)
 		frame->childregs.gprs[15] = new_stackp;
-
-	/* Don't copy runtime instrumentation info */
-	p->thread.ri_cb = NULL;
+	/*
+	 * Clear the runtime instrumentation flag after the above childregs
+	 * copy. The CB pointer was already cleared in arch_dup_task_struct().
+	 */
 	frame->childregs.psw.mask &= ~PSW_MASK_RI;
-	/* Don't copy guarded storage control block */
-	p->thread.gs_cb = NULL;
-	p->thread.gs_bc_cb = NULL;
 
 	/* Set a new TLS ?  */
 	if (clone_flags & CLONE_SETTLS) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/ptrace.c
@@ -392,6 +392,7 @@
 		/*
 		 * floating point control reg. is in the thread structure
 		 */
+		save_fpu_regs();
 		if ((unsigned int) data != 0 ||
 		    test_fp_ctl(data >> (BITS_PER_LONG - 32)))
 			return -EINVAL;
@@ -481,9 +482,7 @@
 		}
 		return 0;
 	case PTRACE_GET_LAST_BREAK:
-		put_user(child->thread.last_break,
-			 (unsigned long __user *) data);
-		return 0;
+		return put_user(child->thread.last_break, (unsigned long __user *)data);
 	case PTRACE_ENABLE_TE:
 		if (!MACHINE_HAS_TE)
 			return -EIO;
@@ -756,6 +755,7 @@
 		/*
 		 * floating point control reg. is in the thread structure
 		 */
+		save_fpu_regs();
 		if (test_fp_ctl(tmp))
 			return -EINVAL;
 		child->thread.fpu.fpc = data;
@@ -837,9 +837,7 @@
 		}
 		return 0;
 	case PTRACE_GET_LAST_BREAK:
-		put_user(child->thread.last_break,
-			 (unsigned int __user *) data);
-		return 0;
+		return put_user(child->thread.last_break, (unsigned int __user *)data);
 	}
 	return compat_ptrace_request(child, request, addr, data);
 }
@@ -921,9 +919,7 @@
 	int rc = 0;
 	freg_t fprs[__NUM_FPRS];
 
-	if (target == current)
-		save_fpu_regs();
-
+	save_fpu_regs();
 	if (MACHINE_HAS_VX)
 		convert_vx_to_fp(fprs, target->thread.fpu.vxrs);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/setup.c
@@ -51,6 +51,7 @@
 #include <linux/start_kernel.h>
 #include <linux/hugetlb.h>
 #include <linux/kmemleak.h>
+#include <linux/security.h>
 
 #include <asm/boot_data.h>
 #include <asm/ipl.h>
@@ -95,10 +96,10 @@
  * relocated above 2 GB, because it has to use 31 bit addresses.
  * Such code and data is part of the .amode31 section.
  */
-unsigned long __amode31_ref __samode31 = __pa(&_samode31);
-unsigned long __amode31_ref __eamode31 = __pa(&_eamode31);
-unsigned long __amode31_ref __stext_amode31 = __pa(&_stext_amode31);
-unsigned long __amode31_ref __etext_amode31 = __pa(&_etext_amode31);
+unsigned long __amode31_ref __samode31 = (unsigned long)&_samode31;
+unsigned long __amode31_ref __eamode31 = (unsigned long)&_eamode31;
+unsigned long __amode31_ref __stext_amode31 = (unsigned long)&_stext_amode31;
+unsigned long __amode31_ref __etext_amode31 = (unsigned long)&_etext_amode31;
 struct exception_table_entry __amode31_ref *__start_amode31_ex_table = _start_amode31_ex_table;
 struct exception_table_entry __amode31_ref *__stop_amode31_ex_table = _stop_amode31_ex_table;
 
@@ -149,11 +150,12 @@
 struct initrd_data __bootdata(initrd_data);
 
 unsigned long __bootdata_preserved(__kaslr_offset);
+unsigned long __bootdata(__amode31_base);
 unsigned int __bootdata_preserved(zlib_dfltcc_support);
 EXPORT_SYMBOL(zlib_dfltcc_support);
 u64 __bootdata_preserved(stfle_fac_list[16]);
 EXPORT_SYMBOL(stfle_fac_list);
-u64 __bootdata_preserved(alt_stfle_fac_list[16]);
+u64 alt_stfle_fac_list[16];
 struct oldmem_data __bootdata_preserved(oldmem_data);
 
 unsigned long VMALLOC_START;
@@ -478,11 +480,12 @@
 	lc->mcck_stack = mcck_stack + STACK_INIT_OFFSET;
 
 	/* Setup absolute zero lowcore */
-	mem_assign_absolute(S390_lowcore.restart_stack, lc->restart_stack);
-	mem_assign_absolute(S390_lowcore.restart_fn, lc->restart_fn);
-	mem_assign_absolute(S390_lowcore.restart_data, lc->restart_data);
-	mem_assign_absolute(S390_lowcore.restart_source, lc->restart_source);
-	mem_assign_absolute(S390_lowcore.restart_psw, lc->restart_psw);
+	put_abs_lowcore(restart_stack, lc->restart_stack);
+	put_abs_lowcore(restart_fn, lc->restart_fn);
+	put_abs_lowcore(restart_data, lc->restart_data);
+	put_abs_lowcore(restart_source, lc->restart_source);
+	put_abs_lowcore(restart_psw, lc->restart_psw);
+	put_abs_lowcore(mcesad, lc->mcesad);
 
 	lc->spinlock_lockval = arch_spin_lockval(0);
 	lc->spinlock_index = 0;
@@ -499,6 +502,7 @@
 static void __init setup_lowcore_dat_on(void)
 {
 	struct lowcore *lc = lowcore_ptr[0];
+	int cr;
 
 	__ctl_clear_bit(0, 28);
 	S390_lowcore.external_new_psw.mask |= PSW_MASK_DAT;
@@ -507,10 +511,10 @@
 	S390_lowcore.io_new_psw.mask |= PSW_MASK_DAT;
 	__ctl_store(S390_lowcore.cregs_save_area, 0, 15);
 	__ctl_set_bit(0, 28);
-	mem_assign_absolute(S390_lowcore.restart_flags, RESTART_FLAG_CTLREGS);
-	mem_assign_absolute(S390_lowcore.program_new_psw, lc->program_new_psw);
-	memcpy_absolute(&S390_lowcore.cregs_save_area, lc->cregs_save_area,
-			sizeof(S390_lowcore.cregs_save_area));
+	put_abs_lowcore(restart_flags, RESTART_FLAG_CTLREGS);
+	put_abs_lowcore(program_new_psw, lc->program_new_psw);
+	for (cr = 0; cr < ARRAY_SIZE(lc->cregs_save_area); cr++)
+		put_abs_lowcore(cregs_save_area[cr], lc->cregs_save_area[cr]);
 }
 
 static struct resource code_resource = {
@@ -593,7 +597,8 @@
 	 * part of the System RAM resource.
 	 */
 	if (crashk_res.end) {
-		memblock_add_node(crashk_res.start, resource_size(&crashk_res), 0);
+		memblock_add_node(crashk_res.start, resource_size(&crashk_res),
+				  0, MEMBLOCK_NONE);
 		memblock_reserve(crashk_res.start, resource_size(&crashk_res));
 		insert_resource(&iomem_resource, &crashk_res);
 	}
@@ -634,14 +639,6 @@
 #endif
 
 /*
- * Make sure that the area above identity mapping is protected
- */
-static void __init reserve_above_ident_map(void)
-{
-	memblock_reserve(ident_map_size, ULONG_MAX);
-}
-
-/*
  * Reserve memory for kdump kernel to be loaded with kexec
  */
 static void __init reserve_crashkernel(void)
@@ -804,12 +801,12 @@
  */
 static void __init reserve_kernel(void)
 {
-	unsigned long start_pfn = PFN_UP(__pa(_end));
-
 	memblock_reserve(0, STARTUP_NORMAL_OFFSET);
-	memblock_reserve((unsigned long)sclp_early_sccb, EXT_SCCB_READ_SCP);
-	memblock_reserve((unsigned long)_stext, PFN_PHYS(start_pfn)
-			 - (unsigned long)_stext);
+	memblock_reserve(OLDMEM_BASE, sizeof(unsigned long));
+	memblock_reserve(OLDMEM_SIZE, sizeof(unsigned long));
+	memblock_reserve(__amode31_base, __eamode31 - __samode31);
+	memblock_reserve(__pa(sclp_early_sccb), EXT_SCCB_READ_SCP);
+	memblock_reserve(__pa(_stext), _end - _stext);
 }
 
 static void __init setup_memory(void)
@@ -824,27 +821,18 @@
 		storage_key_init_range(start, end);
 
 	psw_set_key(PAGE_DEFAULT_KEY);
-
-	/* Only cosmetics */
-	memblock_enforce_memory_limit(memblock_end_of_DRAM());
 }
 
 static void __init relocate_amode31_section(void)
 {
-	unsigned long amode31_addr, amode31_size;
-	long amode31_offset;
+	unsigned long amode31_size = __eamode31 - __samode31;
+	long amode31_offset = __amode31_base - __samode31;
 	long *ptr;
 
-	/* Allocate a new AMODE31 capable memory region */
-	amode31_size = __eamode31 - __samode31;
 	pr_info("Relocating AMODE31 section of size 0x%08lx\n", amode31_size);
-	amode31_addr = (unsigned long)memblock_alloc_low(amode31_size, PAGE_SIZE);
-	if (!amode31_addr)
-		panic("Failed to allocate memory for AMODE31 section\n");
-	amode31_offset = amode31_addr - __samode31;
 
 	/* Move original AMODE31 section to the new one */
-	memmove((void *)amode31_addr, (void *)__samode31, amode31_size);
+	memmove((void *)__amode31_base, (void *)__samode31, amode31_size);
 	/* Zero out the old AMODE31 section to catch invalid accesses within it */
 	memset((void *)__samode31, 0, amode31_size);
 
@@ -891,6 +879,11 @@
 	if (stsi(vmms, 3, 2, 2) == 0 && vmms->count)
 		add_device_randomness(&vmms->vm, sizeof(vmms->vm[0]) * vmms->count);
 	memblock_free((unsigned long) vmms, PAGE_SIZE);
+
+#ifdef CONFIG_ARCH_RANDOM
+	if (cpacf_query_func(CPACF_PRNO, CPACF_PRNO_TRNG))
+		static_branch_enable(&s390_arch_random_available);
+#endif
 }
 
 /*
@@ -981,6 +974,9 @@
 
 	log_component_list();
 
+	if (ipl_get_secureboot())
+		security_lock_kernel_down("Secure IPL mode", LOCKDOWN_INTEGRITY_MAX);
+
 	/* Have one command line that is parsed and saved in /proc/cmdline */
 	/* boot_command_line has been already set up in early.c */
 	*cmdline_p = boot_command_line;
@@ -1005,11 +1001,11 @@
 	setup_control_program_code();
 
 	/* Do some memory reservations *before* memory is added to memblock */
-	reserve_above_ident_map();
 	reserve_kernel();
 	reserve_initrd();
 	reserve_certificate_list();
 	reserve_mem_detect_info();
+	memblock_set_current_limit(ident_map_size);
 	memblock_allow_resize();
 
 	/* Get information about *all* installed memory */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/smp.c
@@ -328,10 +328,17 @@
 	/* Stop target cpu (if func returns this stops the current cpu). */
 	pcpu_sigp_retry(pcpu, SIGP_STOP, 0);
 	/* Restart func on the target cpu and stop the current cpu. */
-	mem_assign_absolute(lc->restart_stack, stack);
-	mem_assign_absolute(lc->restart_fn, (unsigned long) func);
-	mem_assign_absolute(lc->restart_data, (unsigned long) data);
-	mem_assign_absolute(lc->restart_source, source_cpu);
+	if (lc) {
+		lc->restart_stack = stack;
+		lc->restart_fn = (unsigned long)func;
+		lc->restart_data = (unsigned long)data;
+		lc->restart_source = source_cpu;
+	} else {
+		put_abs_lowcore(restart_stack, stack);
+		put_abs_lowcore(restart_fn, (unsigned long)func);
+		put_abs_lowcore(restart_data, (unsigned long)data);
+		put_abs_lowcore(restart_source, source_cpu);
+	}
 	__bpon();
 	asm volatile(
 		"0:	sigp	0,%0,%2	# sigp restart to target cpu\n"
@@ -572,39 +579,27 @@
 }
 
 static DEFINE_SPINLOCK(ctl_lock);
-static unsigned long ctlreg;
 
-/*
- * Set a bit in a control register of all cpus
- */
-void smp_ctl_set_bit(int cr, int bit)
+void smp_ctl_set_clear_bit(int cr, int bit, bool set)
 {
-	struct ec_creg_mask_parms parms = { 1UL << bit, -1UL, cr };
-
-	spin_lock(&ctl_lock);
-	memcpy_absolute(&ctlreg, &S390_lowcore.cregs_save_area[cr], sizeof(ctlreg));
-	__set_bit(bit, &ctlreg);
-	memcpy_absolute(&S390_lowcore.cregs_save_area[cr], &ctlreg, sizeof(ctlreg));
-	spin_unlock(&ctl_lock);
-	on_each_cpu(smp_ctl_bit_callback, &parms, 1);
-}
-EXPORT_SYMBOL(smp_ctl_set_bit);
-
-/*
- * Clear a bit in a control register of all cpus
- */
-void smp_ctl_clear_bit(int cr, int bit)
-{
-	struct ec_creg_mask_parms parms = { 0, ~(1UL << bit), cr };
+	struct ec_creg_mask_parms parms = { .cr = cr, };
+	u64 ctlreg;
 
+	if (set) {
+		parms.orval = 1UL << bit;
+		parms.andval = -1UL;
+	} else {
+		parms.orval = 0;
+		parms.andval = ~(1UL << bit);
+	}
 	spin_lock(&ctl_lock);
-	memcpy_absolute(&ctlreg, &S390_lowcore.cregs_save_area[cr], sizeof(ctlreg));
-	__clear_bit(bit, &ctlreg);
-	memcpy_absolute(&S390_lowcore.cregs_save_area[cr], &ctlreg, sizeof(ctlreg));
+	get_abs_lowcore(ctlreg, cregs_save_area[cr]);
+	ctlreg = (ctlreg & parms.andval) | parms.orval;
+	put_abs_lowcore(cregs_save_area[cr], ctlreg);
 	spin_unlock(&ctl_lock);
 	on_each_cpu(smp_ctl_bit_callback, &parms, 1);
 }
-EXPORT_SYMBOL(smp_ctl_clear_bit);
+EXPORT_SYMBOL(smp_ctl_set_clear_bit);
 
 #ifdef CONFIG_CRASH_DUMP
 
@@ -675,7 +670,7 @@
 	void *regs = (void *) page;
 
 	if (is_boot_cpu)
-		copy_oldmem_kernel(regs, (void *) __LC_FPREGS_SAVE_AREA, 512);
+		copy_oldmem_kernel(regs, __LC_FPREGS_SAVE_AREA, 512);
 	else
 		__pcpu_sigp_relax(addr, SIGP_STORE_STATUS_AT_ADDRESS, page);
 	save_area_add_regs(sa, regs);
@@ -880,7 +875,7 @@
 
 	/* Add CPUs present at boot */
 	__smp_rescan_cpus(info, true);
-	memblock_free_early((unsigned long)info, sizeof(*info));
+	memblock_free((unsigned long)info, sizeof(*info));
 }
 
 /*
@@ -1008,12 +1003,12 @@
 
 void __init smp_prepare_cpus(unsigned int max_cpus)
 {
-	/* request the 0x1201 emergency signal external interrupt */
 	if (register_external_irq(EXT_IRQ_EMERGENCY_SIG, do_ext_call_interrupt))
 		panic("Couldn't request external interrupt 0x1201");
-	/* request the 0x1202 external call external interrupt */
+	ctl_set_bit(0, 14);
 	if (register_external_irq(EXT_IRQ_EXTERNAL_CALL, do_ext_call_interrupt))
 		panic("Couldn't request external interrupt 0x1202");
+	ctl_set_bit(0, 13);
 }
 
 void __init smp_prepare_boot_cpu(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/stacktrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/stacktrace.c
@@ -46,7 +46,7 @@
 		 * Mark stacktraces with kretprobed functions on them
 		 * as unreliable.
 		 */
-		if (state.ip == (unsigned long)kretprobe_trampoline)
+		if (state.ip == (unsigned long)__kretprobe_trampoline)
 			return -EINVAL;
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/sthyi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/sthyi.c
@@ -459,9 +459,9 @@
  *
  * Fills the destination with system information returned by the STHYI
  * instruction. The data is generated by emulation or execution of STHYI,
- * if available. The return value is the condition code that would be
- * returned, the rc parameter is the return code which is passed in
- * register R2 + 1.
+ * if available. The return value is either a negative error value or
+ * the condition code that would be returned, the rc parameter is the
+ * return code which is passed in register R2 + 1.
  */
 int sthyi_fill(void *dst, u64 *rc)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/syscalls/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/syscalls/Makefile
@@ -12,7 +12,7 @@
 uapi-hdrs-y := $(uapi)/unistd_32.h
 uapi-hdrs-y += $(uapi)/unistd_64.h
 
-targets += $(addprefix ../../../,$(gen-y) $(kapi-hdrs-y) $(uapi-hdrs-y))
+targets += $(addprefix ../../../../,$(gen-y) $(kapi-hdrs-y) $(uapi-hdrs-y))
 
 PHONY += kapi uapi
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/syscalls/syscall.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/syscalls/syscall.tbl
@@ -418,7 +418,7 @@
 412	32	utimensat_time64	-				sys_utimensat
 413	32	pselect6_time64		-				compat_sys_pselect6_time64
 414	32	ppoll_time64		-				compat_sys_ppoll_time64
-416	32	io_pgetevents_time64	-				sys_io_pgetevents
+416	32	io_pgetevents_time64	-				compat_sys_io_pgetevents_time64
 417	32	recvmmsg_time64		-				compat_sys_recvmmsg_time64
 418	32	mq_timedsend_time64	-				sys_mq_timedsend
 419	32	mq_timedreceive_time64	-				sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/time.c
@@ -364,7 +364,7 @@
  * Apply clock delta to the global data structures.
  * This is called once on the CPU that performed the clock sync.
  */
-static void clock_sync_global(unsigned long delta)
+static void clock_sync_global(long delta)
 {
 	unsigned long now, adj;
 	struct ptff_qto qto;
@@ -400,7 +400,7 @@
  * Apply clock delta to the per-CPU data structures of this CPU.
  * This is called for each online CPU after the call to clock_sync_global.
  */
-static void clock_sync_local(unsigned long delta)
+static void clock_sync_local(long delta)
 {
 	/* Add the delta to the clock comparator. */
 	if (S390_lowcore.clock_comparator != clock_comparator_max) {
@@ -424,7 +424,7 @@
 struct clock_sync_data {
 	atomic_t cpus;
 	int in_sync;
-	unsigned long clock_delta;
+	long clock_delta;
 };
 
 /*
@@ -544,7 +544,7 @@
 static int stp_sync_clock(void *data)
 {
 	struct clock_sync_data *sync = data;
-	u64 clock_delta, flags;
+	long clock_delta, flags;
 	static int first;
 	int rc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/topology.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/topology.c
@@ -96,7 +96,7 @@
 static void cpu_thread_map(cpumask_t *dst, unsigned int cpu)
 {
 	static cpumask_t mask;
-	int i;
+	unsigned int max_cpu;
 
 	cpumask_clear(&mask);
 	if (!cpumask_test_cpu(cpu, &cpu_setup_mask))
@@ -105,9 +105,10 @@
 	if (topology_mode != TOPOLOGY_MODE_HW)
 		goto out;
 	cpu -= cpu % (smp_cpu_mtid + 1);
-	for (i = 0; i <= smp_cpu_mtid; i++) {
-		if (cpumask_test_cpu(cpu + i, &cpu_setup_mask))
-			cpumask_set_cpu(cpu + i, &mask);
+	max_cpu = min(cpu + smp_cpu_mtid, nr_cpu_ids - 1);
+	for (; cpu <= max_cpu; cpu++) {
+		if (cpumask_test_cpu(cpu, &cpu_setup_mask))
+			cpumask_set_cpu(cpu, &mask);
 	}
 out:
 	cpumask_copy(dst, &mask);
@@ -124,25 +125,26 @@
 	unsigned int core;
 
 	for_each_set_bit(core, &tl_core->mask, TOPOLOGY_CORE_BITS) {
-		unsigned int rcore;
-		int lcpu, i;
+		unsigned int max_cpu, rcore;
+		int cpu;
 
 		rcore = TOPOLOGY_CORE_BITS - 1 - core + tl_core->origin;
-		lcpu = smp_find_processor_id(rcore << smp_cpu_mt_shift);
-		if (lcpu < 0)
+		cpu = smp_find_processor_id(rcore << smp_cpu_mt_shift);
+		if (cpu < 0)
 			continue;
-		for (i = 0; i <= smp_cpu_mtid; i++) {
-			topo = &cpu_topology[lcpu + i];
+		max_cpu = min(cpu + smp_cpu_mtid, nr_cpu_ids - 1);
+		for (; cpu <= max_cpu; cpu++) {
+			topo = &cpu_topology[cpu];
 			topo->drawer_id = drawer->id;
 			topo->book_id = book->id;
 			topo->socket_id = socket->id;
 			topo->core_id = rcore;
-			topo->thread_id = lcpu + i;
+			topo->thread_id = cpu;
 			topo->dedicated = tl_core->d;
-			cpumask_set_cpu(lcpu + i, &drawer->mask);
-			cpumask_set_cpu(lcpu + i, &book->mask);
-			cpumask_set_cpu(lcpu + i, &socket->mask);
-			smp_cpu_set_polarization(lcpu + i, tl_core->pp);
+			cpumask_set_cpu(cpu, &drawer->mask);
+			cpumask_set_cpu(cpu, &book->mask);
+			cpumask_set_cpu(cpu, &socket->mask);
+			smp_cpu_set_polarization(cpu, tl_core->pp);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/traps.c
@@ -84,7 +84,7 @@
 {
 	if (user_mode(regs)) {
 		report_user_fault(regs, SIGSEGV, 0);
-		do_exit(SIGSEGV);
+		force_exit_sig(SIGSEGV);
 	} else
 		die(regs, "Unknown program exception");
 }
@@ -142,10 +142,10 @@
 	do_trap(regs, SIGFPE, si_code, "floating point exception");
 }
 
-static void translation_exception(struct pt_regs *regs)
+static void translation_specification_exception(struct pt_regs *regs)
 {
 	/* May never happen. */
-	panic("Translation exception");
+	panic("Translation-Specification Exception");
 }
 
 static void illegal_op(struct pt_regs *regs)
@@ -281,10 +281,10 @@
 		return;
 	asm volatile(
 		"	mc	0,0\n"
-		"0:	xgr	%0,%0\n"
+		"0:	lhi	%[val],0\n"
 		"1:\n"
-		EX_TABLE(0b,1b)
-		: "+d" (val));
+		EX_TABLE(0b, 1b)
+		: [val] "+d" (val));
 	if (!val)
 		panic("Monitor call doesn't work!\n");
 }
@@ -374,7 +374,7 @@
 	[0x0f]		= hfp_divide_exception,
 	[0x10]		= do_dat_exception,
 	[0x11]		= do_dat_exception,
-	[0x12]		= translation_exception,
+	[0x12]		= translation_specification_exception,
 	[0x13]		= special_op_exception,
 	[0x14]		= default_trap_handler,
 	[0x15]		= operand_exception,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/unwind_bc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/unwind_bc.c
@@ -103,13 +103,11 @@
 	if (sp & 0x7)
 		goto out_err;
 
-	ip = ftrace_graph_ret_addr(state->task, &state->graph_idx, ip, (void *) sp);
-
 	/* Update unwind state */
 	state->sp = sp;
-	state->ip = ip;
 	state->regs = regs;
 	state->reliable = reliable;
+	state->ip = unwind_recover_ret_addr(state, ip);
 	return true;
 
 out_err:
@@ -161,12 +159,10 @@
 		ip = READ_ONCE_NOCHECK(sf->gprs[8]);
 	}
 
-	ip = ftrace_graph_ret_addr(state->task, &state->graph_idx, ip, NULL);
-
 	/* Update unwind state */
 	state->sp = sp;
-	state->ip = ip;
 	state->reliable = true;
+	state->ip = unwind_recover_ret_addr(state, ip);
 
 	if (!first_frame)
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/uv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/uv.c
@@ -165,7 +165,7 @@
 {
 	pte_t entry = READ_ONCE(*ptep);
 	struct page *page;
-	int expected, rc = 0;
+	int expected, cc = 0;
 
 	if (!pte_present(entry))
 		return -ENXIO;
@@ -181,12 +181,25 @@
 	if (!page_ref_freeze(page, expected))
 		return -EBUSY;
 	set_bit(PG_arch_1, &page->flags);
-	rc = uv_call(0, (u64)uvcb);
+	/*
+	 * If the UVC does not succeed or fail immediately, we don't want to
+	 * loop for long, or we might get stall notifications.
+	 * On the other hand, this is a complex scenario and we are holding a lot of
+	 * locks, so we can't easily sleep and reschedule. We try only once,
+	 * and if the UVC returned busy or partial completion, we return
+	 * -EAGAIN and we let the callers deal with it.
+	 */
+	cc = __uv_call(0, (u64)uvcb);
 	page_ref_unfreeze(page, expected);
-	/* Return -ENXIO if the page was not mapped, -EINVAL otherwise */
-	if (rc)
-		rc = uvcb->rc == 0x10a ? -ENXIO : -EINVAL;
-	return rc;
+	/*
+	 * Return -ENXIO if the page was not mapped, -EINVAL for other errors.
+	 * If busy or partially completed, return -EAGAIN.
+	 */
+	if (cc == UVC_CC_OK)
+		return 0;
+	else if (cc == UVC_CC_BUSY || cc == UVC_CC_PARTIAL)
+		return -EAGAIN;
+	return uvcb->rc == 0x10a ? -ENXIO : -EINVAL;
 }
 
 /*
@@ -212,7 +225,7 @@
 	uaddr = __gmap_translate(gmap, gaddr);
 	if (IS_ERR_VALUE(uaddr))
 		goto out;
-	vma = find_vma(gmap->mm, uaddr);
+	vma = vma_lookup(gmap->mm, uaddr);
 	if (!vma)
 		goto out;
 	/*
@@ -239,6 +252,10 @@
 	mmap_read_unlock(gmap->mm);
 
 	if (rc == -EAGAIN) {
+		/*
+		 * If we are here because the UVC returned busy or partial
+		 * completion, this is just a useless check, but it is safe.
+		 */
 		wait_on_page_writeback(page);
 	} else if (rc == -EBUSY) {
 		/*
@@ -343,6 +360,54 @@
 static struct kobj_attribute uv_query_facilities_attr =
 	__ATTR(facilities, 0444, uv_query_facilities, NULL);
 
+static ssize_t uv_query_supp_se_hdr_ver(struct kobject *kobj,
+					struct kobj_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "%lx\n", uv_info.supp_se_hdr_ver);
+}
+
+static struct kobj_attribute uv_query_supp_se_hdr_ver_attr =
+	__ATTR(supp_se_hdr_ver, 0444, uv_query_supp_se_hdr_ver, NULL);
+
+static ssize_t uv_query_supp_se_hdr_pcf(struct kobject *kobj,
+					struct kobj_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "%lx\n", uv_info.supp_se_hdr_pcf);
+}
+
+static struct kobj_attribute uv_query_supp_se_hdr_pcf_attr =
+	__ATTR(supp_se_hdr_pcf, 0444, uv_query_supp_se_hdr_pcf, NULL);
+
+static ssize_t uv_query_dump_cpu_len(struct kobject *kobj,
+				     struct kobj_attribute *attr, char *page)
+{
+	return scnprintf(page, PAGE_SIZE, "%lx\n",
+			uv_info.guest_cpu_stor_len);
+}
+
+static struct kobj_attribute uv_query_dump_cpu_len_attr =
+	__ATTR(uv_query_dump_cpu_len, 0444, uv_query_dump_cpu_len, NULL);
+
+static ssize_t uv_query_dump_storage_state_len(struct kobject *kobj,
+					       struct kobj_attribute *attr, char *page)
+{
+	return scnprintf(page, PAGE_SIZE, "%lx\n",
+			uv_info.conf_dump_storage_state_len);
+}
+
+static struct kobj_attribute uv_query_dump_storage_state_len_attr =
+	__ATTR(dump_storage_state_len, 0444, uv_query_dump_storage_state_len, NULL);
+
+static ssize_t uv_query_dump_finalize_len(struct kobject *kobj,
+					  struct kobj_attribute *attr, char *page)
+{
+	return scnprintf(page, PAGE_SIZE, "%lx\n",
+			uv_info.conf_dump_finalize_len);
+}
+
+static struct kobj_attribute uv_query_dump_finalize_len_attr =
+	__ATTR(dump_finalize_len, 0444, uv_query_dump_finalize_len, NULL);
+
 static ssize_t uv_query_feature_indications(struct kobject *kobj,
 					    struct kobj_attribute *attr, char *buf)
 {
@@ -388,6 +453,11 @@
 	&uv_query_max_guest_cpus_attr.attr,
 	&uv_query_max_guest_vms_attr.attr,
 	&uv_query_max_guest_addr_attr.attr,
+	&uv_query_supp_se_hdr_ver_attr.attr,
+	&uv_query_supp_se_hdr_pcf_attr.attr,
+	&uv_query_dump_storage_state_len_attr.attr,
+	&uv_query_dump_finalize_len_attr.attr,
+	&uv_query_dump_cpu_len_attr.attr,
 	NULL,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/vdso32/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/vdso32/Makefile
@@ -20,9 +20,12 @@
 KBUILD_AFLAGS_32 += -m31 -s
 
 KBUILD_CFLAGS_32 := $(filter-out -m64,$(KBUILD_CFLAGS))
-KBUILD_CFLAGS_32 += -m31 -fPIC -shared -fno-common -fno-builtin
+KBUILD_CFLAGS_32 := $(filter-out -mpacked-stack,$(KBUILD_CFLAGS))
+KBUILD_CFLAGS_32 := $(filter-out -mno-pic-data-is-text-relative,$(KBUILD_CFLAGS_32))
+KBUILD_CFLAGS_32 := $(filter-out -fno-asynchronous-unwind-tables,$(KBUILD_CFLAGS_32))
+KBUILD_CFLAGS_32 += -m31 -fPIC -shared -fno-common -fno-builtin -fasynchronous-unwind-tables
 
-LDFLAGS_vdso32.so.dbg += -fPIC -shared -nostdlib -soname=linux-vdso32.so.1 \
+LDFLAGS_vdso32.so.dbg += -shared -soname=linux-vdso32.so.1 \
 	--hash-style=both --build-id=sha1 -melf_s390 -T
 
 $(targets:%=$(obj)/%.dbg): KBUILD_CFLAGS = $(KBUILD_CFLAGS_32)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/vdso64/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/vdso64/Makefile
@@ -8,8 +8,9 @@
 include $(srctree)/lib/vdso/Makefile
 obj-vdso64 = vdso_user_wrapper.o note.o
 obj-cvdso64 = vdso64_generic.o getcpu.o
-CFLAGS_REMOVE_getcpu.o = -pg $(CC_FLAGS_FTRACE) $(CC_FLAGS_EXPOLINE)
-CFLAGS_REMOVE_vdso64_generic.o = -pg $(CC_FLAGS_FTRACE) $(CC_FLAGS_EXPOLINE)
+VDSO_CFLAGS_REMOVE := -pg $(CC_FLAGS_FTRACE) $(CC_FLAGS_EXPOLINE) $(CC_FLAGS_CHECK_STACK)
+CFLAGS_REMOVE_getcpu.o = $(VDSO_CFLAGS_REMOVE)
+CFLAGS_REMOVE_vdso64_generic.o = $(VDSO_CFLAGS_REMOVE)
 
 # Build rules
 
@@ -24,8 +25,12 @@
 KBUILD_AFLAGS_64 += -m64 -s
 
 KBUILD_CFLAGS_64 := $(filter-out -m64,$(KBUILD_CFLAGS))
-KBUILD_CFLAGS_64 += -m64 -fPIC -shared -fno-common -fno-builtin
-ldflags-y := -fPIC -shared -nostdlib -soname=linux-vdso64.so.1 \
+KBUILD_CFLAGS_64 := $(filter-out -mpacked-stack,$(KBUILD_CFLAGS_64))
+KBUILD_CFLAGS_64 := $(filter-out -mno-pic-data-is-text-relative,$(KBUILD_CFLAGS_64))
+KBUILD_CFLAGS_64 := $(filter-out -munaligned-symbols,$(KBUILD_CFLAGS_64))
+KBUILD_CFLAGS_64 := $(filter-out -fno-asynchronous-unwind-tables,$(KBUILD_CFLAGS_64))
+KBUILD_CFLAGS_64 += -m64 -fPIC -fno-common -fno-builtin -fasynchronous-unwind-tables
+ldflags-y := -shared -soname=linux-vdso64.so.1 \
 	     --hash-style=both --build-id=sha1 -T
 
 $(targets:%=$(obj)/%.dbg): KBUILD_CFLAGS = $(KBUILD_CFLAGS_64)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/vdso64/vdso_user_wrapper.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/vdso64/vdso_user_wrapper.S
@@ -23,8 +23,10 @@
 	CFI_DEF_CFA_OFFSET (STACK_FRAME_OVERHEAD + WRAPPER_FRAME_SIZE)
 	CFI_VAL_OFFSET 15, -STACK_FRAME_OVERHEAD
 	stg	%r14,STACK_FRAME_OVERHEAD(%r15)
+	CFI_REL_OFFSET 14, STACK_FRAME_OVERHEAD
 	brasl	%r14,__s390_vdso_\func
 	lg	%r14,STACK_FRAME_OVERHEAD(%r15)
+	CFI_RESTORE 14
 	aghi	%r15,WRAPPER_FRAME_SIZE
 	CFI_DEF_CFA_OFFSET STACK_FRAME_OVERHEAD
 	CFI_RESTORE 15
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/vmlinux.lds.S
@@ -17,6 +17,8 @@
 /* Handle ro_after_init data on our own. */
 #define RO_AFTER_INIT_DATA
 
+#define RUNTIME_DISCARD_EXIT
+
 #define EMITS_PT_NOTE
 
 #include <asm-generic/vmlinux.lds.h>
@@ -70,6 +72,15 @@
 	. = ALIGN(PAGE_SIZE);
 	__end_ro_after_init = .;
 
+	.data.rel.ro : {
+		*(.data.rel.ro .data.rel.ro.*)
+	}
+	.got : {
+		__got_start = .;
+		*(.got)
+		__got_end = .;
+	}
+
 	RW_DATA(0x100, PAGE_SIZE, THREAD_SIZE)
 	BOOT_DATA_PRESERVED
 
@@ -80,6 +91,7 @@
 		_end_amode31_refs = .;
 	}
 
+	. = ALIGN(PAGE_SIZE);
 	_edata = .;		/* End of data section */
 
 	/* will be freed after init */
@@ -132,6 +144,7 @@
 	/*
 	 * Table with the patch locations to undo expolines
 	*/
+	. = ALIGN(4);
 	.nospec_call_table : {
 		__nospec_call_start = . ;
 		*(.s390_indirect*)
@@ -193,6 +206,7 @@
 
 	BSS_SECTION(PAGE_SIZE, 4 * PAGE_SIZE, PAGE_SIZE)
 
+	. = ALIGN(PAGE_SIZE);
 	_end = . ;
 
 	/*
@@ -212,6 +226,7 @@
 		QUAD(__dynsym_start)				/* dynsym_start */
 		QUAD(__rela_dyn_start)				/* rela_dyn_start */
 		QUAD(__rela_dyn_end)				/* rela_dyn_end */
+		QUAD(_eamode31 - _samode31)			/* amode31_size */
 	} :NONE
 
 	/* Debugging sections.	*/
@@ -223,5 +238,6 @@
 	DISCARDS
 	/DISCARD/ : {
 		*(.eh_frame)
+		*(.interp)
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kernel/vtime.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kernel/vtime.c
@@ -211,13 +211,13 @@
 		virt_timer_expire();
 
 	steal = S390_lowcore.steal_timer;
-	avg_steal = S390_lowcore.avg_steal_timer / 2;
+	avg_steal = S390_lowcore.avg_steal_timer;
 	if ((s64) steal > 0) {
 		S390_lowcore.steal_timer = 0;
 		account_steal_time(cputime_to_nsecs(steal));
 		avg_steal += steal;
 	}
-	S390_lowcore.avg_steal_timer = avg_steal;
+	S390_lowcore.avg_steal_timer = avg_steal / 2;
 }
 
 static u64 vtime_delta(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/Makefile
@@ -12,4 +12,5 @@
 kvm-objs := $(common-objs) kvm-s390.o intercept.o interrupt.o priv.o sigp.o
 kvm-objs += diag.o gaccess.o guestdbg.o vsie.o pv.o
 
+kvm-$(CONFIG_VFIO_PCI_ZDEV_KVM) += pci.o
 obj-$(CONFIG_KVM) += kvm.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/diag.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/diag.c
@@ -77,7 +77,7 @@
 	vcpu->stat.instruction_diagnose_258++;
 	if (vcpu->run->s.regs.gprs[rx] & 7)
 		return kvm_s390_inject_program_int(vcpu, PGM_SPECIFICATION);
-	rc = read_guest(vcpu, vcpu->run->s.regs.gprs[rx], rx, &parm, sizeof(parm));
+	rc = read_guest_real(vcpu, vcpu->run->s.regs.gprs[rx], &parm, sizeof(parm));
 	if (rc)
 		return kvm_s390_inject_prog_cond(vcpu, rc);
 	if (parm.parm_version != 2 || parm.parm_len < 5 || parm.code != 0x258)
@@ -166,6 +166,7 @@
 static int __diag_time_slice_end_directed(struct kvm_vcpu *vcpu)
 {
 	struct kvm_vcpu *tcpu;
+	int tcpu_cpu;
 	int tid;
 
 	tid = vcpu->run->s.regs.gprs[(vcpu->arch.sie_block->ipa & 0xf0) >> 4];
@@ -181,14 +182,15 @@
 		goto no_yield;
 
 	/* target guest VCPU already running */
-	if (READ_ONCE(tcpu->cpu) >= 0) {
+	tcpu_cpu = READ_ONCE(tcpu->cpu);
+	if (tcpu_cpu >= 0) {
 		if (!diag9c_forwarding_hz || diag9c_forwarding_overrun())
 			goto no_yield;
 
 		/* target host CPU already running */
-		if (!vcpu_is_preempted(tcpu->cpu))
+		if (!vcpu_is_preempted(tcpu_cpu))
 			goto no_yield;
-		smp_yield_cpu(tcpu->cpu);
+		smp_yield_cpu(tcpu_cpu);
 		VCPU_EVENT(vcpu, 5,
 			   "diag time slice end directed to %d: yield forwarded",
 			   tid);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/gaccess.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/gaccess.c
@@ -10,6 +10,7 @@
 #include <linux/mm_types.h>
 #include <linux/err.h>
 #include <linux/pgtable.h>
+#include <linux/bitfield.h>
 
 #include <asm/gmap.h>
 #include "kvm-s390.h"
@@ -794,48 +795,270 @@
 	return 1;
 }
 
-static int guest_page_range(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar,
-			    unsigned long *pages, unsigned long nr_pages,
-			    const union asce asce, enum gacc_mode mode)
+static int vm_check_access_key(struct kvm *kvm, u8 access_key,
+			       enum gacc_mode mode, gpa_t gpa)
+{
+	u8 storage_key, access_control;
+	bool fetch_protected;
+	unsigned long hva;
+	int r;
+
+	if (access_key == 0)
+		return 0;
+
+	hva = gfn_to_hva(kvm, gpa_to_gfn(gpa));
+	if (kvm_is_error_hva(hva))
+		return PGM_ADDRESSING;
+
+	mmap_read_lock(current->mm);
+	r = get_guest_storage_key(current->mm, hva, &storage_key);
+	mmap_read_unlock(current->mm);
+	if (r)
+		return r;
+	access_control = FIELD_GET(_PAGE_ACC_BITS, storage_key);
+	if (access_control == access_key)
+		return 0;
+	fetch_protected = storage_key & _PAGE_FP_BIT;
+	if ((mode == GACC_FETCH || mode == GACC_IFETCH) && !fetch_protected)
+		return 0;
+	return PGM_PROTECTION;
+}
+
+static bool fetch_prot_override_applicable(struct kvm_vcpu *vcpu, enum gacc_mode mode,
+					   union asce asce)
 {
 	psw_t *psw = &vcpu->arch.sie_block->gpsw;
+	unsigned long override;
+
+	if (mode == GACC_FETCH || mode == GACC_IFETCH) {
+		/* check if fetch protection override enabled */
+		override = vcpu->arch.sie_block->gcr[0];
+		override &= CR0_FETCH_PROTECTION_OVERRIDE;
+		/* not applicable if subject to DAT && private space */
+		override = override && !(psw_bits(*psw).dat && asce.p);
+		return override;
+	}
+	return false;
+}
+
+static bool fetch_prot_override_applies(unsigned long ga, unsigned int len)
+{
+	return ga < 2048 && ga + len <= 2048;
+}
+
+static bool storage_prot_override_applicable(struct kvm_vcpu *vcpu)
+{
+	/* check if storage protection override enabled */
+	return vcpu->arch.sie_block->gcr[0] & CR0_STORAGE_PROTECTION_OVERRIDE;
+}
+
+static bool storage_prot_override_applies(u8 access_control)
+{
+	/* matches special storage protection override key (9) -> allow */
+	return access_control == PAGE_SPO_ACC;
+}
+
+static int vcpu_check_access_key(struct kvm_vcpu *vcpu, u8 access_key,
+				 enum gacc_mode mode, union asce asce, gpa_t gpa,
+				 unsigned long ga, unsigned int len)
+{
+	u8 storage_key, access_control;
+	unsigned long hva;
+	int r;
+
+	/* access key 0 matches any storage key -> allow */
+	if (access_key == 0)
+		return 0;
+	/*
+	 * caller needs to ensure that gfn is accessible, so we can
+	 * assume that this cannot fail
+	 */
+	hva = gfn_to_hva(vcpu->kvm, gpa_to_gfn(gpa));
+	mmap_read_lock(current->mm);
+	r = get_guest_storage_key(current->mm, hva, &storage_key);
+	mmap_read_unlock(current->mm);
+	if (r)
+		return r;
+	access_control = FIELD_GET(_PAGE_ACC_BITS, storage_key);
+	/* access key matches storage key -> allow */
+	if (access_control == access_key)
+		return 0;
+	if (mode == GACC_FETCH || mode == GACC_IFETCH) {
+		/* it is a fetch and fetch protection is off -> allow */
+		if (!(storage_key & _PAGE_FP_BIT))
+			return 0;
+		if (fetch_prot_override_applicable(vcpu, mode, asce) &&
+		    fetch_prot_override_applies(ga, len))
+			return 0;
+	}
+	if (storage_prot_override_applicable(vcpu) &&
+	    storage_prot_override_applies(access_control))
+		return 0;
+	return PGM_PROTECTION;
+}
+
+/**
+ * guest_range_to_gpas() - Calculate guest physical addresses of page fragments
+ * covering a logical range
+ * @vcpu: virtual cpu
+ * @ga: guest address, start of range
+ * @ar: access register
+ * @gpas: output argument, may be NULL
+ * @len: length of range in bytes
+ * @asce: address-space-control element to use for translation
+ * @mode: access mode
+ * @access_key: access key to mach the range's storage keys against
+ *
+ * Translate a logical range to a series of guest absolute addresses,
+ * such that the concatenation of page fragments starting at each gpa make up
+ * the whole range.
+ * The translation is performed as if done by the cpu for the given @asce, @ar,
+ * @mode and state of the @vcpu.
+ * If the translation causes an exception, its program interruption code is
+ * returned and the &struct kvm_s390_pgm_info pgm member of @vcpu is modified
+ * such that a subsequent call to kvm_s390_inject_prog_vcpu() will inject
+ * a correct exception into the guest.
+ * The resulting gpas are stored into @gpas, unless it is NULL.
+ *
+ * Note: All fragments except the first one start at the beginning of a page.
+ *	 When deriving the boundaries of a fragment from a gpa, all but the last
+ *	 fragment end at the end of the page.
+ *
+ * Return:
+ * * 0		- success
+ * * <0		- translation could not be performed, for example if  guest
+ *		  memory could not be accessed
+ * * >0		- an access exception occurred. In this case the returned value
+ *		  is the program interruption code and the contents of pgm may
+ *		  be used to inject an exception into the guest.
+ */
+static int guest_range_to_gpas(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar,
+			       unsigned long *gpas, unsigned long len,
+			       const union asce asce, enum gacc_mode mode,
+			       u8 access_key)
+{
+	psw_t *psw = &vcpu->arch.sie_block->gpsw;
+	unsigned int offset = offset_in_page(ga);
+	unsigned int fragment_len;
 	int lap_enabled, rc = 0;
 	enum prot_type prot;
+	unsigned long gpa;
 
 	lap_enabled = low_address_protection_enabled(vcpu, asce);
-	while (nr_pages) {
+	while (min(PAGE_SIZE - offset, len) > 0) {
+		fragment_len = min(PAGE_SIZE - offset, len);
 		ga = kvm_s390_logical_to_effective(vcpu, ga);
 		if (mode == GACC_STORE && lap_enabled && is_low_address(ga))
 			return trans_exc(vcpu, PGM_PROTECTION, ga, ar, mode,
 					 PROT_TYPE_LA);
-		ga &= PAGE_MASK;
 		if (psw_bits(*psw).dat) {
-			rc = guest_translate(vcpu, ga, pages, asce, mode, &prot);
+			rc = guest_translate(vcpu, ga, &gpa, asce, mode, &prot);
 			if (rc < 0)
 				return rc;
 		} else {
-			*pages = kvm_s390_real_to_abs(vcpu, ga);
-			if (kvm_is_error_gpa(vcpu->kvm, *pages))
+			gpa = kvm_s390_real_to_abs(vcpu, ga);
+			if (kvm_is_error_gpa(vcpu->kvm, gpa))
 				rc = PGM_ADDRESSING;
 		}
 		if (rc)
 			return trans_exc(vcpu, rc, ga, ar, mode, prot);
-		ga += PAGE_SIZE;
-		pages++;
-		nr_pages--;
+		rc = vcpu_check_access_key(vcpu, access_key, mode, asce, gpa, ga,
+					   fragment_len);
+		if (rc)
+			return trans_exc(vcpu, rc, ga, ar, mode, PROT_TYPE_KEYC);
+		if (gpas)
+			*gpas++ = gpa;
+		offset = 0;
+		ga += fragment_len;
+		len -= fragment_len;
+	}
+	return 0;
+}
+
+static int access_guest_page(struct kvm *kvm, enum gacc_mode mode, gpa_t gpa,
+			     void *data, unsigned int len)
+{
+	const unsigned int offset = offset_in_page(gpa);
+	const gfn_t gfn = gpa_to_gfn(gpa);
+	int rc;
+
+	if (!gfn_to_memslot(kvm, gfn))
+		return PGM_ADDRESSING;
+	if (mode == GACC_STORE)
+		rc = kvm_write_guest_page(kvm, gfn, data, offset, len);
+	else
+		rc = kvm_read_guest_page(kvm, gfn, data, offset, len);
+	return rc;
+}
+
+static int
+access_guest_page_with_key(struct kvm *kvm, enum gacc_mode mode, gpa_t gpa,
+			   void *data, unsigned int len, u8 access_key)
+{
+	struct kvm_memory_slot *slot;
+	bool writable;
+	gfn_t gfn;
+	hva_t hva;
+	int rc;
+
+	gfn = gpa >> PAGE_SHIFT;
+	slot = gfn_to_memslot(kvm, gfn);
+	hva = gfn_to_hva_memslot_prot(slot, gfn, &writable);
+
+	if (kvm_is_error_hva(hva))
+		return PGM_ADDRESSING;
+	/*
+	 * Check if it's a ro memslot, even tho that can't occur (they're unsupported).
+	 * Don't try to actually handle that case.
+	 */
+	if (!writable && mode == GACC_STORE)
+		return -EOPNOTSUPP;
+	hva += offset_in_page(gpa);
+	if (mode == GACC_STORE)
+		rc = copy_to_user_key((void __user *)hva, data, len, access_key);
+	else
+		rc = copy_from_user_key(data, (void __user *)hva, len, access_key);
+	if (rc)
+		return PGM_PROTECTION;
+	if (mode == GACC_STORE)
+		mark_page_dirty_in_slot(kvm, slot, gfn);
+	return 0;
+}
+
+int access_guest_abs_with_key(struct kvm *kvm, gpa_t gpa, void *data,
+			      unsigned long len, enum gacc_mode mode, u8 access_key)
+{
+	int offset = offset_in_page(gpa);
+	int fragment_len;
+	int rc;
+
+	while (min(PAGE_SIZE - offset, len) > 0) {
+		fragment_len = min(PAGE_SIZE - offset, len);
+		rc = access_guest_page_with_key(kvm, mode, gpa, data, fragment_len, access_key);
+		if (rc)
+			return rc;
+		offset = 0;
+		len -= fragment_len;
+		data += fragment_len;
+		gpa += fragment_len;
 	}
 	return 0;
 }
 
-int access_guest(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar, void *data,
-		 unsigned long len, enum gacc_mode mode)
+int access_guest_with_key(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar,
+			  void *data, unsigned long len, enum gacc_mode mode,
+			  u8 access_key)
 {
 	psw_t *psw = &vcpu->arch.sie_block->gpsw;
-	unsigned long _len, nr_pages, gpa, idx;
-	unsigned long pages_array[2];
-	unsigned long *pages;
+	unsigned long nr_pages, idx;
+	unsigned long gpa_array[2];
+	unsigned int fragment_len;
+	unsigned long *gpas;
+	enum prot_type prot;
 	int need_ipte_lock;
 	union asce asce;
+	bool try_storage_prot_override;
+	bool try_fetch_prot_override;
 	int rc;
 
 	if (!len)
@@ -845,60 +1068,87 @@
 	if (rc)
 		return rc;
 	nr_pages = (((ga & ~PAGE_MASK) + len - 1) >> PAGE_SHIFT) + 1;
-	pages = pages_array;
-	if (nr_pages > ARRAY_SIZE(pages_array))
-		pages = vmalloc(array_size(nr_pages, sizeof(unsigned long)));
-	if (!pages)
+	gpas = gpa_array;
+	if (nr_pages > ARRAY_SIZE(gpa_array))
+		gpas = vmalloc(array_size(nr_pages, sizeof(unsigned long)));
+	if (!gpas)
 		return -ENOMEM;
+	try_fetch_prot_override = fetch_prot_override_applicable(vcpu, mode, asce);
+	try_storage_prot_override = storage_prot_override_applicable(vcpu);
 	need_ipte_lock = psw_bits(*psw).dat && !asce.r;
 	if (need_ipte_lock)
 		ipte_lock(vcpu);
-	rc = guest_page_range(vcpu, ga, ar, pages, nr_pages, asce, mode);
-	for (idx = 0; idx < nr_pages && !rc; idx++) {
-		gpa = *(pages + idx) + (ga & ~PAGE_MASK);
-		_len = min(PAGE_SIZE - (gpa & ~PAGE_MASK), len);
-		if (mode == GACC_STORE)
-			rc = kvm_write_guest(vcpu->kvm, gpa, data, _len);
-		else
-			rc = kvm_read_guest(vcpu->kvm, gpa, data, _len);
-		len -= _len;
-		ga += _len;
-		data += _len;
+	/*
+	 * Since we do the access further down ultimately via a move instruction
+	 * that does key checking and returns an error in case of a protection
+	 * violation, we don't need to do the check during address translation.
+	 * Skip it by passing access key 0, which matches any storage key,
+	 * obviating the need for any further checks. As a result the check is
+	 * handled entirely in hardware on access, we only need to take care to
+	 * forego key protection checking if fetch protection override applies or
+	 * retry with the special key 9 in case of storage protection override.
+	 */
+	rc = guest_range_to_gpas(vcpu, ga, ar, gpas, len, asce, mode, 0);
+	if (rc)
+		goto out_unlock;
+	for (idx = 0; idx < nr_pages; idx++) {
+		fragment_len = min(PAGE_SIZE - offset_in_page(gpas[idx]), len);
+		if (try_fetch_prot_override && fetch_prot_override_applies(ga, fragment_len)) {
+			rc = access_guest_page(vcpu->kvm, mode, gpas[idx],
+					       data, fragment_len);
+		} else {
+			rc = access_guest_page_with_key(vcpu->kvm, mode, gpas[idx],
+							data, fragment_len, access_key);
+		}
+		if (rc == PGM_PROTECTION && try_storage_prot_override)
+			rc = access_guest_page_with_key(vcpu->kvm, mode, gpas[idx],
+							data, fragment_len, PAGE_SPO_ACC);
+		if (rc == PGM_PROTECTION)
+			prot = PROT_TYPE_KEYC;
+		if (rc)
+			break;
+		len -= fragment_len;
+		data += fragment_len;
+		ga = kvm_s390_logical_to_effective(vcpu, ga + fragment_len);
 	}
+	if (rc > 0)
+		rc = trans_exc(vcpu, rc, ga, ar, mode, prot);
+out_unlock:
 	if (need_ipte_lock)
 		ipte_unlock(vcpu);
-	if (nr_pages > ARRAY_SIZE(pages_array))
-		vfree(pages);
+	if (nr_pages > ARRAY_SIZE(gpa_array))
+		vfree(gpas);
 	return rc;
 }
 
 int access_guest_real(struct kvm_vcpu *vcpu, unsigned long gra,
 		      void *data, unsigned long len, enum gacc_mode mode)
 {
-	unsigned long _len, gpa;
+	unsigned int fragment_len;
+	unsigned long gpa;
 	int rc = 0;
 
 	while (len && !rc) {
 		gpa = kvm_s390_real_to_abs(vcpu, gra);
-		_len = min(PAGE_SIZE - (gpa & ~PAGE_MASK), len);
-		if (mode)
-			rc = write_guest_abs(vcpu, gpa, data, _len);
-		else
-			rc = read_guest_abs(vcpu, gpa, data, _len);
-		len -= _len;
-		gra += _len;
-		data += _len;
+		fragment_len = min(PAGE_SIZE - offset_in_page(gpa), len);
+		rc = access_guest_page(vcpu->kvm, mode, gpa, data, fragment_len);
+		len -= fragment_len;
+		gra += fragment_len;
+		data += fragment_len;
 	}
+	if (rc > 0)
+		vcpu->arch.pgm.code = rc;
 	return rc;
 }
 
 /**
- * guest_translate_address - translate guest logical into guest absolute address
+ * guest_translate_address_with_key - translate guest logical into guest absolute address
  * @vcpu: virtual cpu
  * @gva: Guest virtual address
  * @ar: Access register
  * @gpa: Guest physical address
  * @mode: Translation access mode
+ * @access_key: access key to mach the storage key with
  *
  * Parameter semantics are the same as the ones from guest_translate.
  * The memory contents at the guest address are not changed.
@@ -906,11 +1156,10 @@
  * Note: The IPTE lock is not taken during this function, so the caller
  * has to take care of this.
  */
-int guest_translate_address(struct kvm_vcpu *vcpu, unsigned long gva, u8 ar,
-			    unsigned long *gpa, enum gacc_mode mode)
+int guest_translate_address_with_key(struct kvm_vcpu *vcpu, unsigned long gva, u8 ar,
+				     unsigned long *gpa, enum gacc_mode mode,
+				     u8 access_key)
 {
-	psw_t *psw = &vcpu->arch.sie_block->gpsw;
-	enum prot_type prot;
 	union asce asce;
 	int rc;
 
@@ -918,23 +1167,8 @@
 	rc = get_vcpu_asce(vcpu, &asce, gva, ar, mode);
 	if (rc)
 		return rc;
-	if (is_low_address(gva) && low_address_protection_enabled(vcpu, asce)) {
-		if (mode == GACC_STORE)
-			return trans_exc(vcpu, PGM_PROTECTION, gva, 0,
-					 mode, PROT_TYPE_LA);
-	}
-
-	if (psw_bits(*psw).dat && !asce.r) {	/* Use DAT? */
-		rc = guest_translate(vcpu, gva, gpa, asce, mode, &prot);
-		if (rc > 0)
-			return trans_exc(vcpu, rc, gva, 0, mode, prot);
-	} else {
-		*gpa = kvm_s390_real_to_abs(vcpu, gva);
-		if (kvm_is_error_gpa(vcpu->kvm, *gpa))
-			return trans_exc(vcpu, rc, gva, PGM_ADDRESSING, mode, 0);
-	}
-
-	return rc;
+	return guest_range_to_gpas(vcpu, gva, ar, gpa, 1, asce, mode,
+				   access_key);
 }
 
 /**
@@ -944,26 +1178,48 @@
  * @ar: Access register
  * @length: Length of test range
  * @mode: Translation access mode
+ * @access_key: access key to mach the storage keys with
  */
 int check_gva_range(struct kvm_vcpu *vcpu, unsigned long gva, u8 ar,
-		    unsigned long length, enum gacc_mode mode)
+		    unsigned long length, enum gacc_mode mode, u8 access_key)
 {
-	unsigned long gpa;
-	unsigned long currlen;
+	union asce asce;
 	int rc = 0;
 
+	rc = get_vcpu_asce(vcpu, &asce, gva, ar, mode);
+	if (rc)
+		return rc;
 	ipte_lock(vcpu);
-	while (length > 0 && !rc) {
-		currlen = min(length, PAGE_SIZE - (gva % PAGE_SIZE));
-		rc = guest_translate_address(vcpu, gva, ar, &gpa, mode);
-		gva += currlen;
-		length -= currlen;
-	}
+	rc = guest_range_to_gpas(vcpu, gva, ar, NULL, length, asce, mode,
+				 access_key);
 	ipte_unlock(vcpu);
 
 	return rc;
 }
 
+/**
+ * check_gpa_range - test a range of guest physical addresses for accessibility
+ * @kvm: virtual machine instance
+ * @gpa: guest physical address
+ * @length: length of test range
+ * @mode: access mode to test, relevant for storage keys
+ * @access_key: access key to mach the storage keys with
+ */
+int check_gpa_range(struct kvm *kvm, unsigned long gpa, unsigned long length,
+		    enum gacc_mode mode, u8 access_key)
+{
+	unsigned int fragment_len;
+	int rc = 0;
+
+	while (length && !rc) {
+		fragment_len = min(PAGE_SIZE - offset_in_page(gpa), length);
+		rc = vm_check_access_key(kvm, access_key, mode, gpa);
+		length -= fragment_len;
+		gpa += fragment_len;
+	}
+	return rc;
+}
+
 /**
  * kvm_s390_check_low_addr_prot_real - check for low-address protection
  * @vcpu: virtual cpu
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/gaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/gaccess.h
@@ -186,24 +186,34 @@
 	GACC_IFETCH,
 };
 
-int guest_translate_address(struct kvm_vcpu *vcpu, unsigned long gva,
-			    u8 ar, unsigned long *gpa, enum gacc_mode mode);
+int guest_translate_address_with_key(struct kvm_vcpu *vcpu, unsigned long gva, u8 ar,
+				     unsigned long *gpa, enum gacc_mode mode,
+				     u8 access_key);
+
 int check_gva_range(struct kvm_vcpu *vcpu, unsigned long gva, u8 ar,
-		    unsigned long length, enum gacc_mode mode);
+		    unsigned long length, enum gacc_mode mode, u8 access_key);
+
+int check_gpa_range(struct kvm *kvm, unsigned long gpa, unsigned long length,
+		    enum gacc_mode mode, u8 access_key);
+
+int access_guest_abs_with_key(struct kvm *kvm, gpa_t gpa, void *data,
+			      unsigned long len, enum gacc_mode mode, u8 access_key);
 
-int access_guest(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar, void *data,
-		 unsigned long len, enum gacc_mode mode);
+int access_guest_with_key(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar,
+			  void *data, unsigned long len, enum gacc_mode mode,
+			  u8 access_key);
 
 int access_guest_real(struct kvm_vcpu *vcpu, unsigned long gra,
 		      void *data, unsigned long len, enum gacc_mode mode);
 
 /**
- * write_guest - copy data from kernel space to guest space
+ * write_guest_with_key - copy data from kernel space to guest space
  * @vcpu: virtual cpu
  * @ga: guest address
  * @ar: access register
  * @data: source address in kernel space
  * @len: number of bytes to copy
+ * @access_key: access key the storage key needs to match
  *
  * Copy @len bytes from @data (kernel space) to @ga (guest address).
  * In order to copy data to guest space the PSW of the vcpu is inspected:
@@ -214,8 +224,8 @@
  * The addressing mode of the PSW is also inspected, so that address wrap
  * around is taken into account for 24-, 31- and 64-bit addressing mode,
  * if the to be copied data crosses page boundaries in guest address space.
- * In addition also low address and DAT protection are inspected before
- * copying any data (key protection is currently not implemented).
+ * In addition low address, DAT and key protection checks are performed before
+ * copying any data.
  *
  * This function modifies the 'struct kvm_s390_pgm_info pgm' member of @vcpu.
  * In case of an access exception (e.g. protection exception) pgm will contain
@@ -243,10 +253,53 @@
  *	 if data has been changed in guest space in case of an exception.
  */
 static inline __must_check
+int write_guest_with_key(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar,
+			 void *data, unsigned long len, u8 access_key)
+{
+	return access_guest_with_key(vcpu, ga, ar, data, len, GACC_STORE,
+				     access_key);
+}
+
+/**
+ * write_guest - copy data from kernel space to guest space
+ * @vcpu: virtual cpu
+ * @ga: guest address
+ * @ar: access register
+ * @data: source address in kernel space
+ * @len: number of bytes to copy
+ *
+ * The behaviour of write_guest is identical to write_guest_with_key, except
+ * that the PSW access key is used instead of an explicit argument.
+ */
+static inline __must_check
 int write_guest(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar, void *data,
 		unsigned long len)
 {
-	return access_guest(vcpu, ga, ar, data, len, GACC_STORE);
+	u8 access_key = psw_bits(vcpu->arch.sie_block->gpsw).key;
+
+	return write_guest_with_key(vcpu, ga, ar, data, len, access_key);
+}
+
+/**
+ * read_guest_with_key - copy data from guest space to kernel space
+ * @vcpu: virtual cpu
+ * @ga: guest address
+ * @ar: access register
+ * @data: destination address in kernel space
+ * @len: number of bytes to copy
+ * @access_key: access key the storage key needs to match
+ *
+ * Copy @len bytes from @ga (guest address) to @data (kernel space).
+ *
+ * The behaviour of read_guest_with_key is identical to write_guest_with_key,
+ * except that data will be copied from guest space to kernel space.
+ */
+static inline __must_check
+int read_guest_with_key(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar,
+			void *data, unsigned long len, u8 access_key)
+{
+	return access_guest_with_key(vcpu, ga, ar, data, len, GACC_FETCH,
+				     access_key);
 }
 
 /**
@@ -259,14 +312,16 @@
  *
  * Copy @len bytes from @ga (guest address) to @data (kernel space).
  *
- * The behaviour of read_guest is identical to write_guest, except that
- * data will be copied from guest space to kernel space.
+ * The behaviour of read_guest is identical to read_guest_with_key, except
+ * that the PSW access key is used instead of an explicit argument.
  */
 static inline __must_check
 int read_guest(struct kvm_vcpu *vcpu, unsigned long ga, u8 ar, void *data,
 	       unsigned long len)
 {
-	return access_guest(vcpu, ga, ar, data, len, GACC_FETCH);
+	u8 access_key = psw_bits(vcpu->arch.sie_block->gpsw).key;
+
+	return read_guest_with_key(vcpu, ga, ar, data, len, access_key);
 }
 
 /**
@@ -287,7 +342,10 @@
 int read_guest_instr(struct kvm_vcpu *vcpu, unsigned long ga, void *data,
 		     unsigned long len)
 {
-	return access_guest(vcpu, ga, 0, data, len, GACC_IFETCH);
+	u8 access_key = psw_bits(vcpu->arch.sie_block->gpsw).key;
+
+	return access_guest_with_key(vcpu, ga, 0, data, len, GACC_IFETCH,
+				     access_key);
 }
 
 /**
@@ -344,11 +402,12 @@
  * @len: number of bytes to copy
  *
  * Copy @len bytes from @data (kernel space) to @gra (guest real address).
- * It is up to the caller to ensure that the entire guest memory range is
- * valid memory before calling this function.
  * Guest low address and key protection are not checked.
  *
- * Returns zero on success or -EFAULT on error.
+ * Returns zero on success, -EFAULT when copying from @data failed, or
+ * PGM_ADRESSING in case @gra is outside a memslot. In this case, pgm check info
+ * is also stored to allow injecting into the guest (if applicable) using
+ * kvm_s390_inject_prog_cond().
  *
  * If an error occurs data may have been copied partially to guest memory.
  */
@@ -367,11 +426,12 @@
  * @len: number of bytes to copy
  *
  * Copy @len bytes from @gra (guest real address) to @data (kernel space).
- * It is up to the caller to ensure that the entire guest memory range is
- * valid memory before calling this function.
  * Guest key protection is not checked.
  *
- * Returns zero on success or -EFAULT on error.
+ * Returns zero on success, -EFAULT when copying to @data failed, or
+ * PGM_ADRESSING in case @gra is outside a memslot. In this case, pgm check info
+ * is also stored to allow injecting into the guest (if applicable) using
+ * kvm_s390_inject_prog_cond().
  *
  * If an error occurs data may have been copied partially to kernel space.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/intercept.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/intercept.c
@@ -271,10 +271,18 @@
  * handle_external_interrupt - used for external interruption interceptions
  * @vcpu: virtual cpu
  *
- * This interception only occurs if the CPUSTAT_EXT_INT bit was set, or if
- * the new PSW does not have external interrupts disabled. In the first case,
- * we've got to deliver the interrupt manually, and in the second case, we
- * drop to userspace to handle the situation there.
+ * This interception occurs if:
+ * - the CPUSTAT_EXT_INT bit was already set when the external interrupt
+ *   occurred. In this case, the interrupt needs to be injected manually to
+ *   preserve interrupt priority.
+ * - the external new PSW has external interrupts enabled, which will cause an
+ *   interruption loop. We drop to userspace in this case.
+ *
+ * The latter case can be detected by inspecting the external mask bit in the
+ * external new psw.
+ *
+ * Under PV, only the latter case can occur, since interrupt priorities are
+ * handled in the ultravisor.
  */
 static int handle_external_interrupt(struct kvm_vcpu *vcpu)
 {
@@ -285,10 +293,18 @@
 
 	vcpu->stat.exit_external_interrupt++;
 
-	rc = read_guest_lc(vcpu, __LC_EXT_NEW_PSW, &newpsw, sizeof(psw_t));
-	if (rc)
-		return rc;
-	/* We can not handle clock comparator or timer interrupt with bad PSW */
+	if (kvm_s390_pv_cpu_is_protected(vcpu)) {
+		newpsw = vcpu->arch.sie_block->gpsw;
+	} else {
+		rc = read_guest_lc(vcpu, __LC_EXT_NEW_PSW, &newpsw, sizeof(psw_t));
+		if (rc)
+			return rc;
+	}
+
+	/*
+	 * Clock comparator or timer interrupt with external interrupt enabled
+	 * will cause interrupt loop. Drop to userspace.
+	 */
 	if ((eic == EXT_IRQ_CLK_COMP || eic == EXT_IRQ_CPU_TIMER) &&
 	    (newpsw.mask & PSW_MASK_EXT))
 		return -EOPNOTSUPP;
@@ -331,18 +347,18 @@
 
 	kvm_s390_get_regs_rre(vcpu, &reg1, &reg2);
 
-	/* Make sure that the source is paged-in */
-	rc = guest_translate_address(vcpu, vcpu->run->s.regs.gprs[reg2],
-				     reg2, &srcaddr, GACC_FETCH);
+	/* Ensure that the source is paged-in, no actual access -> no key checking */
+	rc = guest_translate_address_with_key(vcpu, vcpu->run->s.regs.gprs[reg2],
+					      reg2, &srcaddr, GACC_FETCH, 0);
 	if (rc)
 		return kvm_s390_inject_prog_cond(vcpu, rc);
 	rc = kvm_arch_fault_in_page(vcpu, srcaddr, 0);
 	if (rc != 0)
 		return rc;
 
-	/* Make sure that the destination is paged-in */
-	rc = guest_translate_address(vcpu, vcpu->run->s.regs.gprs[reg1],
-				     reg1, &dstaddr, GACC_STORE);
+	/* Ensure that the source is paged-in, no actual access -> no key checking */
+	rc = guest_translate_address_with_key(vcpu, vcpu->run->s.regs.gprs[reg1],
+					      reg1, &dstaddr, GACC_STORE, 0);
 	if (rc)
 		return kvm_s390_inject_prog_cond(vcpu, rc);
 	rc = kvm_arch_fault_in_page(vcpu, dstaddr, 1);
@@ -373,8 +389,8 @@
  */
 int handle_sthyi(struct kvm_vcpu *vcpu)
 {
-	int reg1, reg2, r = 0;
-	u64 code, addr, cc = 0, rc = 0;
+	int reg1, reg2, cc = 0, r = 0;
+	u64 code, addr, rc = 0;
 	struct sthyi_sctns *sctns = NULL;
 
 	if (!test_kvm_facility(vcpu->kvm, 74))
@@ -405,7 +421,10 @@
 		return -ENOMEM;
 
 	cc = sthyi_fill(sctns, &rc);
-
+	if (cc < 0) {
+		free_page((unsigned long)sctns);
+		return cc;
+	}
 out:
 	if (!cc) {
 		if (kvm_s390_pv_cpu_is_protected(vcpu)) {
@@ -518,17 +537,37 @@
 	 */
 	if (rc == -EINVAL)
 		return 0;
+	/*
+	 * If we got -EAGAIN here, we simply return it. It will eventually
+	 * get propagated all the way to userspace, which should then try
+	 * again.
+	 */
 	return rc;
 }
 
 static int handle_pv_notification(struct kvm_vcpu *vcpu)
 {
+	int ret;
+
 	if (vcpu->arch.sie_block->ipa == 0xb210)
 		return handle_pv_spx(vcpu);
 	if (vcpu->arch.sie_block->ipa == 0xb220)
 		return handle_pv_sclp(vcpu);
 	if (vcpu->arch.sie_block->ipa == 0xb9a4)
 		return handle_pv_uvc(vcpu);
+	if (vcpu->arch.sie_block->ipa >> 8 == 0xae) {
+		/*
+		 * Besides external call, other SIGP orders also cause a
+		 * 108 (pv notify) intercept. In contrast to external call,
+		 * these orders need to be emulated and hence the appropriate
+		 * place to handle them is in handle_instruction().
+		 * So first try kvm_s390_handle_sigp_pei() and if that isn't
+		 * successful, go on with handle_instruction().
+		 */
+		ret = kvm_s390_handle_sigp_pei(vcpu);
+		if (!ret)
+			return ret;
+	}
 
 	return handle_instruction(vcpu);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/interrupt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/interrupt.c
@@ -28,9 +28,11 @@
 #include <asm/switch_to.h>
 #include <asm/nmi.h>
 #include <asm/airq.h>
+#include <asm/tpi.h>
 #include "kvm-s390.h"
 #include "gaccess.h"
 #include "trace-s390.h"
+#include "pci.h"
 
 #define PFAULT_INIT 0x0600
 #define PFAULT_DONE 0x0680
@@ -81,8 +83,9 @@
 		struct esca_block *sca = vcpu->kvm->arch.sca;
 		union esca_sigp_ctrl *sigp_ctrl =
 			&(sca->cpu[vcpu->vcpu_id].sigp_ctrl);
-		union esca_sigp_ctrl new_val = {0}, old_val = *sigp_ctrl;
+		union esca_sigp_ctrl new_val = {0}, old_val;
 
+		old_val = READ_ONCE(*sigp_ctrl);
 		new_val.scn = src_id;
 		new_val.c = 1;
 		old_val.c = 0;
@@ -93,8 +96,9 @@
 		struct bsca_block *sca = vcpu->kvm->arch.sca;
 		union bsca_sigp_ctrl *sigp_ctrl =
 			&(sca->cpu[vcpu->vcpu_id].sigp_ctrl);
-		union bsca_sigp_ctrl new_val = {0}, old_val = *sigp_ctrl;
+		union bsca_sigp_ctrl new_val = {0}, old_val;
 
+		old_val = READ_ONCE(*sigp_ctrl);
 		new_val.scn = src_id;
 		new_val.c = 1;
 		old_val.c = 0;
@@ -124,16 +128,18 @@
 		struct esca_block *sca = vcpu->kvm->arch.sca;
 		union esca_sigp_ctrl *sigp_ctrl =
 			&(sca->cpu[vcpu->vcpu_id].sigp_ctrl);
-		union esca_sigp_ctrl old = *sigp_ctrl;
+		union esca_sigp_ctrl old;
 
+		old = READ_ONCE(*sigp_ctrl);
 		expect = old.value;
 		rc = cmpxchg(&sigp_ctrl->value, old.value, 0);
 	} else {
 		struct bsca_block *sca = vcpu->kvm->arch.sca;
 		union bsca_sigp_ctrl *sigp_ctrl =
 			&(sca->cpu[vcpu->vcpu_id].sigp_ctrl);
-		union bsca_sigp_ctrl old = *sigp_ctrl;
+		union bsca_sigp_ctrl old;
 
+		old = READ_ONCE(*sigp_ctrl);
 		expect = old.value;
 		rc = cmpxchg(&sigp_ctrl->value, old.value, 0);
 	}
@@ -1900,13 +1906,12 @@
 	isc = int_word_to_isc(inti->io.io_int_word);
 
 	/*
-	 * Do not make use of gisa in protected mode. We do not use the lock
-	 * checking variant as this is just a performance optimization and we
-	 * do not hold the lock here. This is ok as the code will pick
-	 * interrupts from both "lists" for delivery.
+	 * We do not use the lock checking variant as this is just a
+	 * performance optimization and we do not hold the lock here.
+	 * This is ok as the code will pick interrupts from both "lists"
+	 * for delivery.
 	 */
-	if (!kvm_s390_pv_get_handle(kvm) &&
-	    gi->origin && inti->type & KVM_S390_INT_IO_AI_MASK) {
+	if (gi->origin && inti->type & KVM_S390_INT_IO_AI_MASK) {
 		VM_EVENT(kvm, 4, "%s isc %1u", "inject: I/O (AI/gisa)", isc);
 		gisa_set_ipm_gisc(gi->origin, isc);
 		kfree(inti);
@@ -2115,6 +2120,13 @@
 	return test_bit(IRQ_PEND_SIGP_STOP, &li->pending_irqs);
 }
 
+int kvm_s390_is_restart_irq_pending(struct kvm_vcpu *vcpu)
+{
+	struct kvm_s390_local_interrupt *li = &vcpu->arch.local_int;
+
+	return test_bit(IRQ_PEND_RESTART, &li->pending_irqs);
+}
+
 void kvm_s390_clear_stop_irq(struct kvm_vcpu *vcpu)
 {
 	struct kvm_s390_local_interrupt *li = &vcpu->arch.local_int;
@@ -3163,9 +3175,33 @@
 	VM_EVENT(kvm, 3, "gisa 0x%pK initialized", gi->origin);
 }
 
+void kvm_s390_gisa_enable(struct kvm *kvm)
+{
+	struct kvm_s390_gisa_interrupt *gi = &kvm->arch.gisa_int;
+	struct kvm_vcpu *vcpu;
+	unsigned long i;
+	u32 gisa_desc;
+
+	if (gi->origin)
+		return;
+	kvm_s390_gisa_init(kvm);
+	gisa_desc = kvm_s390_get_gisa_desc(kvm);
+	if (!gisa_desc)
+		return;
+	kvm_for_each_vcpu(i, vcpu, kvm) {
+		mutex_lock(&vcpu->mutex);
+		vcpu->arch.sie_block->gd = gisa_desc;
+		vcpu->arch.sie_block->eca |= ECA_AIV;
+		VCPU_EVENT(vcpu, 3, "AIV gisa format-%u enabled for cpu %03u",
+			   vcpu->arch.sie_block->gd & 0x3, vcpu->vcpu_id);
+		mutex_unlock(&vcpu->mutex);
+	}
+}
+
 void kvm_s390_gisa_destroy(struct kvm *kvm)
 {
 	struct kvm_s390_gisa_interrupt *gi = &kvm->arch.gisa_int;
+	struct kvm_s390_gisa *gisa = gi->origin;
 
 	if (!gi->origin)
 		return;
@@ -3176,6 +3212,25 @@
 		cpu_relax();
 	hrtimer_cancel(&gi->timer);
 	gi->origin = NULL;
+	VM_EVENT(kvm, 3, "gisa 0x%pK destroyed", gisa);
+}
+
+void kvm_s390_gisa_disable(struct kvm *kvm)
+{
+	struct kvm_s390_gisa_interrupt *gi = &kvm->arch.gisa_int;
+	struct kvm_vcpu *vcpu;
+	unsigned long i;
+
+	if (!gi->origin)
+		return;
+	kvm_for_each_vcpu(i, vcpu, kvm) {
+		mutex_lock(&vcpu->mutex);
+		vcpu->arch.sie_block->eca &= ~ECA_AIV;
+		vcpu->arch.sie_block->gd = 0U;
+		mutex_unlock(&vcpu->mutex);
+		VCPU_EVENT(vcpu, 3, "AIV disabled for cpu %03u", vcpu->vcpu_id);
+	}
+	kvm_s390_gisa_destroy(kvm);
 }
 
 /**
@@ -3261,10 +3316,87 @@
 }
 EXPORT_SYMBOL_GPL(kvm_s390_gisc_unregister);
 
-static void gib_alert_irq_handler(struct airq_struct *airq, bool floating)
+static void aen_host_forward(unsigned long si)
+{
+	struct kvm_s390_gisa_interrupt *gi;
+	struct zpci_gaite *gaite;
+	struct kvm *kvm;
+
+	gaite = (struct zpci_gaite *)aift->gait +
+		(si * sizeof(struct zpci_gaite));
+	if (gaite->count == 0)
+		return;
+	if (gaite->aisb != 0)
+		set_bit_inv(gaite->aisbo, phys_to_virt(gaite->aisb));
+
+	kvm = kvm_s390_pci_si_to_kvm(aift, si);
+	if (!kvm)
+		return;
+	gi = &kvm->arch.gisa_int;
+
+	if (!(gi->origin->g1.simm & AIS_MODE_MASK(gaite->gisc)) ||
+	    !(gi->origin->g1.nimm & AIS_MODE_MASK(gaite->gisc))) {
+		gisa_set_ipm_gisc(gi->origin, gaite->gisc);
+		if (hrtimer_active(&gi->timer))
+			hrtimer_cancel(&gi->timer);
+		hrtimer_start(&gi->timer, 0, HRTIMER_MODE_REL);
+		kvm->stat.aen_forward++;
+	}
+}
+
+static void aen_process_gait(u8 isc)
+{
+	bool found = false, first = true;
+	union zpci_sic_iib iib = {{0}};
+	unsigned long si, flags;
+
+	spin_lock_irqsave(&aift->gait_lock, flags);
+
+	if (!aift->gait) {
+		spin_unlock_irqrestore(&aift->gait_lock, flags);
+		return;
+	}
+
+	for (si = 0;;) {
+		/* Scan adapter summary indicator bit vector */
+		si = airq_iv_scan(aift->sbv, si, airq_iv_end(aift->sbv));
+		if (si == -1UL) {
+			if (first || found) {
+				/* Re-enable interrupts. */
+				zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, isc,
+						  &iib);
+				first = found = false;
+			} else {
+				/* Interrupts on and all bits processed */
+				break;
+			}
+			found = false;
+			si = 0;
+			/* Scan again after re-enabling interrupts */
+			continue;
+		}
+		found = true;
+		aen_host_forward(si);
+	}
+
+	spin_unlock_irqrestore(&aift->gait_lock, flags);
+}
+
+static void gib_alert_irq_handler(struct airq_struct *airq,
+				  struct tpi_info *tpi_info)
 {
+	struct tpi_adapter_info *info = (struct tpi_adapter_info *)tpi_info;
+
 	inc_irq_stat(IRQIO_GAL);
-	process_gib_alert_list();
+
+	if ((info->forward || info->error) &&
+	    IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM)) {
+		aen_process_gait(info->isc);
+		if (info->aism != 0)
+			process_gib_alert_list();
+	} else {
+		process_gib_alert_list();
+	}
 }
 
 static struct airq_struct gib_alert_irq = {
@@ -3276,6 +3408,11 @@
 {
 	if (!gib)
 		return;
+	if (kvm_s390_pci_interp_allowed() && aift) {
+		mutex_lock(&aift->aift_lock);
+		kvm_s390_pci_aen_exit();
+		mutex_unlock(&aift->aift_lock);
+	}
 	chsc_sgib(0);
 	unregister_adapter_interrupt(&gib_alert_irq);
 	free_page((unsigned long)gib);
@@ -3313,6 +3450,14 @@
 		goto out_unreg_gal;
 	}
 
+	if (kvm_s390_pci_interp_allowed()) {
+		if (kvm_s390_pci_aen_init(nisc)) {
+			pr_err("Initializing AEN for PCI failed\n");
+			rc = -EIO;
+			goto out_unreg_gal;
+		}
+	}
+
 	KVM_EVENT(3, "gib 0x%pK (nisc=%d) initialized", gib, gib->nisc);
 	goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/kvm-s390.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/kvm-s390.c
@@ -48,6 +48,7 @@
 #include <asm/fpu/api.h>
 #include "kvm-s390.h"
 #include "gaccess.h"
+#include "pci.h"
 
 #define CREATE_TRACE_POINTS
 #include "trace.h"
@@ -64,7 +65,8 @@
 	STATS_DESC_COUNTER(VM, inject_float_mchk),
 	STATS_DESC_COUNTER(VM, inject_pfault_done),
 	STATS_DESC_COUNTER(VM, inject_service_signal),
-	STATS_DESC_COUNTER(VM, inject_virtio)
+	STATS_DESC_COUNTER(VM, inject_virtio),
+	STATS_DESC_COUNTER(VM, aen_forward)
 };
 
 const struct kvm_stats_header kvm_vm_stats_header = {
@@ -123,6 +125,7 @@
 	STATS_DESC_COUNTER(VCPU, instruction_io_other),
 	STATS_DESC_COUNTER(VCPU, instruction_lpsw),
 	STATS_DESC_COUNTER(VCPU, instruction_lpswe),
+	STATS_DESC_COUNTER(VCPU, instruction_lpswey),
 	STATS_DESC_COUNTER(VCPU, instruction_pfmf),
 	STATS_DESC_COUNTER(VCPU, instruction_ptff),
 	STATS_DESC_COUNTER(VCPU, instruction_sck),
@@ -503,6 +506,14 @@
 		goto out;
 	}
 
+	if (IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM)) {
+		rc = kvm_s390_pci_init();
+		if (rc) {
+			pr_err("Unable to allocate AIFT for PCI\n");
+			goto out;
+		}
+	}
+
 	rc = kvm_s390_gib_init(GAL_ISC);
 	if (rc)
 		goto out;
@@ -517,6 +528,8 @@
 void kvm_arch_exit(void)
 {
 	kvm_s390_gib_destroy();
+	if (IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM))
+		kvm_s390_pci_exit();
 	debug_unregister(kvm_s390_dbf);
 	debug_unregister(kvm_s390_dbf_uv);
 }
@@ -564,6 +577,7 @@
 	case KVM_CAP_S390_VCPU_RESETS:
 	case KVM_CAP_SET_GUEST_DEBUG:
 	case KVM_CAP_S390_DIAG318:
+	case KVM_CAP_S390_MEM_OP_EXTENSION:
 		r = 1;
 		break;
 	case KVM_CAP_SET_GUEST_DEBUG2:
@@ -604,6 +618,29 @@
 	case KVM_CAP_S390_PROTECTED:
 		r = is_prot_virt_host();
 		break;
+	case KVM_CAP_S390_ZPCI_OP:
+		r = kvm_s390_pci_interp_allowed();
+		break;
+	case KVM_CAP_S390_PROTECTED_DUMP: {
+		u64 pv_cmds_dump[] = {
+			BIT_UVC_CMD_DUMP_INIT,
+			BIT_UVC_CMD_DUMP_CONFIG_STOR_STATE,
+			BIT_UVC_CMD_DUMP_CPU,
+			BIT_UVC_CMD_DUMP_COMPLETE,
+		};
+		int i;
+
+		r = is_prot_virt_host();
+
+		for (i = 0; i < ARRAY_SIZE(pv_cmds_dump); i++) {
+			if (!test_bit_inv(pv_cmds_dump[i],
+					  (unsigned long *)&uv_info.inst_calls_list)) {
+				r = 0;
+				break;
+			}
+		}
+		break;
+	}
 	default:
 		r = 0;
 	}
@@ -1017,6 +1054,42 @@
 	return 0;
 }
 
+static void kvm_s390_vcpu_pci_setup(struct kvm_vcpu *vcpu)
+{
+	/* Only set the ECB bits after guest requests zPCI interpretation */
+	if (!vcpu->kvm->arch.use_zpci_interp)
+		return;
+
+	vcpu->arch.sie_block->ecb2 |= ECB2_ZPCI_LSI;
+	vcpu->arch.sie_block->ecb3 |= ECB3_AISII + ECB3_AISI;
+}
+
+void kvm_s390_vcpu_pci_enable_interp(struct kvm *kvm)
+{
+	struct kvm_vcpu *vcpu;
+	unsigned long i;
+
+	lockdep_assert_held(&kvm->lock);
+
+	if (!kvm_s390_pci_interp_allowed())
+		return;
+
+	/*
+	 * If host is configured for PCI and the necessary facilities are
+	 * available, turn on interpretation for the life of this guest
+	 */
+	kvm->arch.use_zpci_interp = 1;
+
+	kvm_s390_vcpu_block_all(kvm);
+
+	kvm_for_each_vcpu(i, vcpu, kvm) {
+		kvm_s390_vcpu_pci_setup(vcpu);
+		kvm_s390_sync_request(KVM_REQ_VSIE_RESTART, vcpu);
+	}
+
+	kvm_s390_vcpu_unblock_all(kvm);
+}
+
 static void kvm_s390_sync_request_broadcast(struct kvm *kvm, int req)
 {
 	int cx;
@@ -1117,6 +1190,8 @@
 	return 0;
 }
 
+static void __kvm_s390_set_tod_clock(struct kvm *kvm, const struct kvm_s390_vm_tod_clock *gtod);
+
 static int kvm_s390_set_tod_ext(struct kvm *kvm, struct kvm_device_attr *attr)
 {
 	struct kvm_s390_vm_tod_clock gtod;
@@ -1126,7 +1201,7 @@
 
 	if (!test_kvm_facility(kvm, 139) && gtod.epoch_idx)
 		return -EINVAL;
-	kvm_s390_set_tod_clock(kvm, &gtod);
+	__kvm_s390_set_tod_clock(kvm, &gtod);
 
 	VM_EVENT(kvm, 3, "SET: TOD extension: 0x%x, TOD base: 0x%llx",
 		gtod.epoch_idx, gtod.tod);
@@ -1157,7 +1232,7 @@
 			   sizeof(gtod.tod)))
 		return -EFAULT;
 
-	kvm_s390_set_tod_clock(kvm, &gtod);
+	__kvm_s390_set_tod_clock(kvm, &gtod);
 	VM_EVENT(kvm, 3, "SET: TOD base: 0x%llx", gtod.tod);
 	return 0;
 }
@@ -1169,6 +1244,16 @@
 	if (attr->flags)
 		return -EINVAL;
 
+	mutex_lock(&kvm->lock);
+	/*
+	 * For protected guests, the TOD is managed by the ultravisor, so trying
+	 * to change it will never bring the expected results.
+	 */
+	if (kvm_s390_pv_is_protected(kvm)) {
+		ret = -EOPNOTSUPP;
+		goto out_unlock;
+	}
+
 	switch (attr->attr) {
 	case KVM_S390_VM_TOD_EXT:
 		ret = kvm_s390_set_tod_ext(kvm, attr);
@@ -1183,6 +1268,9 @@
 		ret = -ENXIO;
 		break;
 	}
+
+out_unlock:
+	mutex_unlock(&kvm->lock);
 	return ret;
 }
 
@@ -2015,6 +2103,10 @@
 		ms = slots->memslots + slotidx;
 		ofs = 0;
 	}
+
+	if (cur_gfn < ms->base_gfn)
+		ofs = 0;
+
 	ofs = find_next_bit(kvm_second_dirty_bitmap(ms), ms->npages, ofs);
 	while ((slotidx > 0) && (ofs >= ms->npages)) {
 		slotidx--;
@@ -2223,6 +2315,9 @@
 		}
 		mutex_unlock(&vcpu->mutex);
 	}
+	/* Ensure that we re-enable gisa if the non-PV guest used it but the PV guest did not. */
+	if (use_gisa)
+		kvm_s390_gisa_enable(kvm);
 	return ret;
 }
 
@@ -2233,6 +2328,10 @@
 
 	struct kvm_vcpu *vcpu;
 
+	/* Disable the GISA if the ultravisor does not support AIV. */
+	if (!test_bit_inv(BIT_UV_FEAT_AIV, &uv_info.uv_feature_indications))
+		kvm_s390_gisa_disable(kvm);
+
 	kvm_for_each_vcpu(i, vcpu, kvm) {
 		mutex_lock(&vcpu->mutex);
 		r = kvm_s390_pv_create_cpu(vcpu, rc, rrc);
@@ -2245,6 +2344,115 @@
 	return r;
 }
 
+/*
+ * Here we provide user space with a direct interface to query UV
+ * related data like UV maxima and available features as well as
+ * feature specific data.
+ *
+ * To facilitate future extension of the data structures we'll try to
+ * write data up to the maximum requested length.
+ */
+static ssize_t kvm_s390_handle_pv_info(struct kvm_s390_pv_info *info)
+{
+	ssize_t len_min;
+
+	switch (info->header.id) {
+	case KVM_PV_INFO_VM: {
+		len_min =  sizeof(info->header) + sizeof(info->vm);
+
+		if (info->header.len_max < len_min)
+			return -EINVAL;
+
+		memcpy(info->vm.inst_calls_list,
+		       uv_info.inst_calls_list,
+		       sizeof(uv_info.inst_calls_list));
+
+		/* It's max cpuid not max cpus, so it's off by one */
+		info->vm.max_cpus = uv_info.max_guest_cpu_id + 1;
+		info->vm.max_guests = uv_info.max_num_sec_conf;
+		info->vm.max_guest_addr = uv_info.max_sec_stor_addr;
+		info->vm.feature_indication = uv_info.uv_feature_indications;
+
+		return len_min;
+	}
+	case KVM_PV_INFO_DUMP: {
+		len_min =  sizeof(info->header) + sizeof(info->dump);
+
+		if (info->header.len_max < len_min)
+			return -EINVAL;
+
+		info->dump.dump_cpu_buffer_len = uv_info.guest_cpu_stor_len;
+		info->dump.dump_config_mem_buffer_per_1m = uv_info.conf_dump_storage_state_len;
+		info->dump.dump_config_finalize_len = uv_info.conf_dump_finalize_len;
+		return len_min;
+	}
+	default:
+		return -EINVAL;
+	}
+}
+
+static int kvm_s390_pv_dmp(struct kvm *kvm, struct kvm_pv_cmd *cmd,
+			   struct kvm_s390_pv_dmp dmp)
+{
+	int r = -EINVAL;
+	void __user *result_buff = (void __user *)dmp.buff_addr;
+
+	switch (dmp.subcmd) {
+	case KVM_PV_DUMP_INIT: {
+		if (kvm->arch.pv.dumping)
+			break;
+
+		/*
+		 * Block SIE entry as concurrent dump UVCs could lead
+		 * to validities.
+		 */
+		kvm_s390_vcpu_block_all(kvm);
+
+		r = uv_cmd_nodata(kvm_s390_pv_get_handle(kvm),
+				  UVC_CMD_DUMP_INIT, &cmd->rc, &cmd->rrc);
+		KVM_UV_EVENT(kvm, 3, "PROTVIRT DUMP INIT: rc %x rrc %x",
+			     cmd->rc, cmd->rrc);
+		if (!r) {
+			kvm->arch.pv.dumping = true;
+		} else {
+			kvm_s390_vcpu_unblock_all(kvm);
+			r = -EINVAL;
+		}
+		break;
+	}
+	case KVM_PV_DUMP_CONFIG_STOR_STATE: {
+		if (!kvm->arch.pv.dumping)
+			break;
+
+		/*
+		 * gaddr is an output parameter since we might stop
+		 * early. As dmp will be copied back in our caller, we
+		 * don't need to do it ourselves.
+		 */
+		r = kvm_s390_pv_dump_stor_state(kvm, result_buff, &dmp.gaddr, dmp.buff_len,
+						&cmd->rc, &cmd->rrc);
+		break;
+	}
+	case KVM_PV_DUMP_COMPLETE: {
+		if (!kvm->arch.pv.dumping)
+			break;
+
+		r = -EINVAL;
+		if (dmp.buff_len < uv_info.conf_dump_finalize_len)
+			break;
+
+		r = kvm_s390_pv_dump_complete(kvm, result_buff,
+					      &cmd->rc, &cmd->rrc);
+		break;
+	}
+	default:
+		r = -ENOTTY;
+		break;
+	}
+
+	return r;
+}
+
 static int kvm_s390_handle_pv(struct kvm *kvm, struct kvm_pv_cmd *cmd)
 {
 	int r = 0;
@@ -2381,12 +2589,151 @@
 			     cmd->rc, cmd->rrc);
 		break;
 	}
+	case KVM_PV_INFO: {
+		struct kvm_s390_pv_info info = {};
+		ssize_t data_len;
+
+		/*
+		 * No need to check the VM protection here.
+		 *
+		 * Maybe user space wants to query some of the data
+		 * when the VM is still unprotected. If we see the
+		 * need to fence a new data command we can still
+		 * return an error in the info handler.
+		 */
+
+		r = -EFAULT;
+		if (copy_from_user(&info, argp, sizeof(info.header)))
+			break;
+
+		r = -EINVAL;
+		if (info.header.len_max < sizeof(info.header))
+			break;
+
+		data_len = kvm_s390_handle_pv_info(&info);
+		if (data_len < 0) {
+			r = data_len;
+			break;
+		}
+		/*
+		 * If a data command struct is extended (multiple
+		 * times) this can be used to determine how much of it
+		 * is valid.
+		 */
+		info.header.len_written = data_len;
+
+		r = -EFAULT;
+		if (copy_to_user(argp, &info, data_len))
+			break;
+
+		r = 0;
+		break;
+	}
+	case KVM_PV_DUMP: {
+		struct kvm_s390_pv_dmp dmp;
+
+		r = -EINVAL;
+		if (!kvm_s390_pv_is_protected(kvm))
+			break;
+
+		r = -EFAULT;
+		if (copy_from_user(&dmp, argp, sizeof(dmp)))
+			break;
+
+		r = kvm_s390_pv_dmp(kvm, cmd, dmp);
+		if (r)
+			break;
+
+		if (copy_to_user(argp, &dmp, sizeof(dmp))) {
+			r = -EFAULT;
+			break;
+		}
+
+		break;
+	}
 	default:
 		r = -ENOTTY;
 	}
 	return r;
 }
 
+static bool access_key_invalid(u8 access_key)
+{
+	return access_key > 0xf;
+}
+
+static int kvm_s390_vm_mem_op(struct kvm *kvm, struct kvm_s390_mem_op *mop)
+{
+	void __user *uaddr = (void __user *)mop->buf;
+	u64 supported_flags;
+	void *tmpbuf = NULL;
+	int r, srcu_idx;
+
+	supported_flags = KVM_S390_MEMOP_F_SKEY_PROTECTION
+			  | KVM_S390_MEMOP_F_CHECK_ONLY;
+	if (mop->flags & ~supported_flags || !mop->size)
+		return -EINVAL;
+	if (mop->size > MEM_OP_MAX_SIZE)
+		return -E2BIG;
+	if (kvm_s390_pv_is_protected(kvm))
+		return -EINVAL;
+	if (mop->flags & KVM_S390_MEMOP_F_SKEY_PROTECTION) {
+		if (access_key_invalid(mop->key))
+			return -EINVAL;
+	} else {
+		mop->key = 0;
+	}
+	if (!(mop->flags & KVM_S390_MEMOP_F_CHECK_ONLY)) {
+		tmpbuf = vmalloc(mop->size);
+		if (!tmpbuf)
+			return -ENOMEM;
+	}
+
+	srcu_idx = srcu_read_lock(&kvm->srcu);
+
+	if (kvm_is_error_gpa(kvm, mop->gaddr)) {
+		r = PGM_ADDRESSING;
+		goto out_unlock;
+	}
+
+	switch (mop->op) {
+	case KVM_S390_MEMOP_ABSOLUTE_READ: {
+		if (mop->flags & KVM_S390_MEMOP_F_CHECK_ONLY) {
+			r = check_gpa_range(kvm, mop->gaddr, mop->size, GACC_FETCH, mop->key);
+		} else {
+			r = access_guest_abs_with_key(kvm, mop->gaddr, tmpbuf,
+						      mop->size, GACC_FETCH, mop->key);
+			if (r == 0) {
+				if (copy_to_user(uaddr, tmpbuf, mop->size))
+					r = -EFAULT;
+			}
+		}
+		break;
+	}
+	case KVM_S390_MEMOP_ABSOLUTE_WRITE: {
+		if (mop->flags & KVM_S390_MEMOP_F_CHECK_ONLY) {
+			r = check_gpa_range(kvm, mop->gaddr, mop->size, GACC_STORE, mop->key);
+		} else {
+			if (copy_from_user(tmpbuf, uaddr, mop->size)) {
+				r = -EFAULT;
+				break;
+			}
+			r = access_guest_abs_with_key(kvm, mop->gaddr, tmpbuf,
+						      mop->size, GACC_STORE, mop->key);
+		}
+		break;
+	}
+	default:
+		r = -EINVAL;
+	}
+
+out_unlock:
+	srcu_read_unlock(&kvm->srcu, srcu_idx);
+
+	vfree(tmpbuf);
+	return r;
+}
+
 long kvm_arch_vm_ioctl(struct file *filp,
 		       unsigned int ioctl, unsigned long arg)
 {
@@ -2487,8 +2834,8 @@
 	case KVM_S390_PV_COMMAND: {
 		struct kvm_pv_cmd args;
 
-		/* protvirt means user sigp */
-		kvm->arch.user_cpu_state_ctrl = 1;
+		/* protvirt means user cpu state */
+		kvm_s390_set_user_cpu_state_ctrl(kvm);
 		r = 0;
 		if (!is_prot_virt_host()) {
 			r = -EINVAL;
@@ -2511,6 +2858,28 @@
 		}
 		break;
 	}
+	case KVM_S390_MEM_OP: {
+		struct kvm_s390_mem_op mem_op;
+
+		if (copy_from_user(&mem_op, argp, sizeof(mem_op)) == 0)
+			r = kvm_s390_vm_mem_op(kvm, &mem_op);
+		else
+			r = -EFAULT;
+		break;
+	}
+	case KVM_S390_ZPCI_OP: {
+		struct kvm_s390_zpci_op args;
+
+		r = -EINVAL;
+		if (!IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM))
+			break;
+		if (copy_from_user(&args, argp, sizeof(args))) {
+			r = -EFAULT;
+			break;
+		}
+		r = kvm_s390_pci_zpci_op(kvm, &args);
+		break;
+	}
 	default:
 		r = -ENOTTY;
 	}
@@ -2672,6 +3041,14 @@
 	kvm->arch.sca = NULL;
 }
 
+void kvm_arch_free_vm(struct kvm *kvm)
+{
+	if (IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM))
+		kvm_s390_pci_clear_list(kvm);
+
+	__kvm_arch_free_vm(kvm);
+}
+
 int kvm_arch_init_vm(struct kvm *kvm, unsigned long type)
 {
 	gfp_t alloc_flags = GFP_KERNEL_ACCOUNT;
@@ -2754,6 +3131,13 @@
 
 	kvm_s390_crypto_init(kvm);
 
+	if (IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM)) {
+		mutex_lock(&kvm->lock);
+		kvm_s390_pci_init_list(kvm);
+		kvm_s390_vcpu_pci_enable_interp(kvm);
+		mutex_unlock(&kvm->lock);
+	}
+
 	mutex_init(&kvm->arch.float_int.ais_lock);
 	spin_lock_init(&kvm->arch.float_int.lock);
 	for (i = 0; i < FIRQ_LIST_COUNT; i++)
@@ -3270,6 +3654,8 @@
 
 	kvm_s390_vcpu_crypto_setup(vcpu);
 
+	kvm_s390_vcpu_pci_setup(vcpu);
+
 	mutex_lock(&vcpu->kvm->lock);
 	if (kvm_s390_pv_is_protected(vcpu->kvm)) {
 		rc = kvm_s390_pv_create_cpu(vcpu, &uvrc, &uvrrc);
@@ -3307,9 +3693,7 @@
 
 	vcpu->arch.sie_block->icpua = vcpu->vcpu_id;
 	spin_lock_init(&vcpu->arch.local_int.lock);
-	vcpu->arch.sie_block->gd = (u32)(u64)vcpu->kvm->arch.gisa_int.origin;
-	if (vcpu->arch.sie_block->gd && sclp.has_gisaf)
-		vcpu->arch.sie_block->gd |= GISA_FORMAT1;
+	vcpu->arch.sie_block->gd = kvm_s390_get_gisa_desc(vcpu->kvm);
 	seqcount_init(&vcpu->arch.cputm_seqcount);
 
 	vcpu->arch.pfault_token = KVM_S390_PFAULT_TOKEN_INVALID;
@@ -3447,7 +3831,7 @@
 {
 	/* do not poll with more than halt_poll_max_steal percent of steal time */
 	if (S390_lowcore.avg_steal_timer * 100 / (TICK_USEC << 12) >=
-	    halt_poll_max_steal) {
+	    READ_ONCE(halt_poll_max_steal)) {
 		vcpu->stat.halt_no_poll_steal++;
 		return true;
 	}
@@ -3681,10 +4065,6 @@
 
 	vcpu_load(vcpu);
 
-	if (test_fp_ctl(fpu->fpc)) {
-		ret = -EINVAL;
-		goto out;
-	}
 	vcpu->run->s.regs.fpc = fpu->fpc;
 	if (MACHINE_HAS_VX)
 		convert_fp_to_vx((__vector128 *) vcpu->run->s.regs.vrs,
@@ -3692,7 +4072,6 @@
 	else
 		memcpy(vcpu->run->s.regs.fprs, &fpu->fprs, sizeof(fpu->fprs));
 
-out:
 	vcpu_put(vcpu);
 	return ret;
 }
@@ -3802,7 +4181,7 @@
 	vcpu_load(vcpu);
 
 	/* user space knows about this interface - let it control the state */
-	vcpu->kvm->arch.user_cpu_state_ctrl = 1;
+	kvm_s390_set_user_cpu_state_ctrl(vcpu->kvm);
 
 	switch (mp_state->mp_state) {
 	case KVM_MP_STATE_STOPPED:
@@ -3913,14 +4292,12 @@
 	return 0;
 }
 
-void kvm_s390_set_tod_clock(struct kvm *kvm,
-			    const struct kvm_s390_vm_tod_clock *gtod)
+static void __kvm_s390_set_tod_clock(struct kvm *kvm, const struct kvm_s390_vm_tod_clock *gtod)
 {
 	struct kvm_vcpu *vcpu;
 	union tod_clock clk;
 	int i;
 
-	mutex_lock(&kvm->lock);
 	preempt_disable();
 
 	store_tod_clock_ext(&clk);
@@ -3941,7 +4318,15 @@
 
 	kvm_s390_vcpu_unblock_all(kvm);
 	preempt_enable();
+}
+
+int kvm_s390_try_set_tod_clock(struct kvm *kvm, const struct kvm_s390_vm_tod_clock *gtod)
+{
+	if (!mutex_trylock(&kvm->lock))
+		return 0;
+	__kvm_s390_set_tod_clock(kvm, gtod);
 	mutex_unlock(&kvm->lock);
+	return 1;
 }
 
 /**
@@ -4255,6 +4640,7 @@
 	if (kvm_run->kvm_dirty_regs & KVM_SYNC_DIAG318) {
 		vcpu->arch.diag318_info.val = kvm_run->s.regs.diag318;
 		vcpu->arch.sie_block->cpnc = vcpu->arch.diag318_info.cpnc;
+		VCPU_EVENT(vcpu, 3, "setting cpnc to %d", vcpu->arch.diag318_info.cpnc);
 	}
 	/*
 	 * If userspace sets the riccb (e.g. after migration) to a valid state,
@@ -4407,6 +4793,15 @@
 	struct kvm_run *kvm_run = vcpu->run;
 	int rc;
 
+	/*
+	 * Running a VM while dumping always has the potential to
+	 * produce inconsistent dump data. But for PV vcpus a SIE
+	 * entry while dumping could also lead to a fatal validity
+	 * intercept which we absolutely want to avoid.
+	 */
+	if (vcpu->kvm->arch.pv.dumping)
+		return -EINVAL;
+
 	if (kvm_run->immediate_exit)
 		return -EINTR;
 
@@ -4642,10 +5037,15 @@
 		}
 	}
 
-	/* SIGP STOP and SIGP STOP AND STORE STATUS has been fully processed */
+	/*
+	 * Set the VCPU to STOPPED and THEN clear the interrupt flag,
+	 * now that the SIGP STOP and SIGP STOP AND STORE STATUS orders
+	 * have been fully processed. This will ensure that the VCPU
+	 * is kept BUSY if another VCPU is inquiring with SIGP SENSE.
+	 */
+	kvm_s390_set_cpuflags(vcpu, CPUSTAT_STOPPED);
 	kvm_s390_clear_stop_irq(vcpu);
 
-	kvm_s390_set_cpuflags(vcpu, CPUSTAT_STOPPED);
 	__disable_ibs_on_vcpu(vcpu);
 
 	for (i = 0; i < online_vcpus; i++) {
@@ -4691,8 +5091,8 @@
 	return r;
 }
 
-static long kvm_s390_guest_sida_op(struct kvm_vcpu *vcpu,
-				   struct kvm_s390_mem_op *mop)
+static long kvm_s390_vcpu_sida_op(struct kvm_vcpu *vcpu,
+				  struct kvm_s390_mem_op *mop)
 {
 	void __user *uaddr = (void __user *)mop->buf;
 	int r = 0;
@@ -4703,6 +5103,8 @@
 		return -EINVAL;
 	if (mop->size + mop->sida_offset > sida_size(vcpu->arch.sie_block))
 		return -E2BIG;
+	if (!kvm_s390_pv_cpu_is_protected(vcpu))
+		return -EINVAL;
 
 	switch (mop->op) {
 	case KVM_S390_MEMOP_SIDA_READ:
@@ -4719,24 +5121,29 @@
 	}
 	return r;
 }
-static long kvm_s390_guest_mem_op(struct kvm_vcpu *vcpu,
-				  struct kvm_s390_mem_op *mop)
+
+static long kvm_s390_vcpu_mem_op(struct kvm_vcpu *vcpu,
+				 struct kvm_s390_mem_op *mop)
 {
 	void __user *uaddr = (void __user *)mop->buf;
 	void *tmpbuf = NULL;
 	int r = 0;
 	const u64 supported_flags = KVM_S390_MEMOP_F_INJECT_EXCEPTION
-				    | KVM_S390_MEMOP_F_CHECK_ONLY;
+				    | KVM_S390_MEMOP_F_CHECK_ONLY
+				    | KVM_S390_MEMOP_F_SKEY_PROTECTION;
 
 	if (mop->flags & ~supported_flags || mop->ar >= NUM_ACRS || !mop->size)
 		return -EINVAL;
-
 	if (mop->size > MEM_OP_MAX_SIZE)
 		return -E2BIG;
-
 	if (kvm_s390_pv_cpu_is_protected(vcpu))
 		return -EINVAL;
-
+	if (mop->flags & KVM_S390_MEMOP_F_SKEY_PROTECTION) {
+		if (access_key_invalid(mop->key))
+			return -EINVAL;
+	} else {
+		mop->key = 0;
+	}
 	if (!(mop->flags & KVM_S390_MEMOP_F_CHECK_ONLY)) {
 		tmpbuf = vmalloc(mop->size);
 		if (!tmpbuf)
@@ -4746,11 +5153,12 @@
 	switch (mop->op) {
 	case KVM_S390_MEMOP_LOGICAL_READ:
 		if (mop->flags & KVM_S390_MEMOP_F_CHECK_ONLY) {
-			r = check_gva_range(vcpu, mop->gaddr, mop->ar,
-					    mop->size, GACC_FETCH);
+			r = check_gva_range(vcpu, mop->gaddr, mop->ar, mop->size,
+					    GACC_FETCH, mop->key);
 			break;
 		}
-		r = read_guest(vcpu, mop->gaddr, mop->ar, tmpbuf, mop->size);
+		r = read_guest_with_key(vcpu, mop->gaddr, mop->ar, tmpbuf,
+					mop->size, mop->key);
 		if (r == 0) {
 			if (copy_to_user(uaddr, tmpbuf, mop->size))
 				r = -EFAULT;
@@ -4758,15 +5166,16 @@
 		break;
 	case KVM_S390_MEMOP_LOGICAL_WRITE:
 		if (mop->flags & KVM_S390_MEMOP_F_CHECK_ONLY) {
-			r = check_gva_range(vcpu, mop->gaddr, mop->ar,
-					    mop->size, GACC_STORE);
+			r = check_gva_range(vcpu, mop->gaddr, mop->ar, mop->size,
+					    GACC_STORE, mop->key);
 			break;
 		}
 		if (copy_from_user(tmpbuf, uaddr, mop->size)) {
 			r = -EFAULT;
 			break;
 		}
-		r = write_guest(vcpu, mop->gaddr, mop->ar, tmpbuf, mop->size);
+		r = write_guest_with_key(vcpu, mop->gaddr, mop->ar, tmpbuf,
+					 mop->size, mop->key);
 		break;
 	}
 
@@ -4777,8 +5186,8 @@
 	return r;
 }
 
-static long kvm_s390_guest_memsida_op(struct kvm_vcpu *vcpu,
-				      struct kvm_s390_mem_op *mop)
+static long kvm_s390_vcpu_memsida_op(struct kvm_vcpu *vcpu,
+				     struct kvm_s390_mem_op *mop)
 {
 	int r, srcu_idx;
 
@@ -4787,12 +5196,12 @@
 	switch (mop->op) {
 	case KVM_S390_MEMOP_LOGICAL_READ:
 	case KVM_S390_MEMOP_LOGICAL_WRITE:
-		r = kvm_s390_guest_mem_op(vcpu, mop);
+		r = kvm_s390_vcpu_mem_op(vcpu, mop);
 		break;
 	case KVM_S390_MEMOP_SIDA_READ:
 	case KVM_S390_MEMOP_SIDA_WRITE:
 		/* we are locked against sida going away by the vcpu->mutex */
-		r = kvm_s390_guest_sida_op(vcpu, mop);
+		r = kvm_s390_vcpu_sida_op(vcpu, mop);
 		break;
 	default:
 		r = -EINVAL;
@@ -4830,6 +5239,48 @@
 	return -ENOIOCTLCMD;
 }
 
+static int kvm_s390_handle_pv_vcpu_dump(struct kvm_vcpu *vcpu,
+					struct kvm_pv_cmd *cmd)
+{
+	struct kvm_s390_pv_dmp dmp;
+	void *data;
+	int ret;
+
+	/* Dump initialization is a prerequisite */
+	if (!vcpu->kvm->arch.pv.dumping)
+		return -EINVAL;
+
+	if (copy_from_user(&dmp, (__u8 __user *)cmd->data, sizeof(dmp)))
+		return -EFAULT;
+
+	/* We only handle this subcmd right now */
+	if (dmp.subcmd != KVM_PV_DUMP_CPU)
+		return -EINVAL;
+
+	/* CPU dump length is the same as create cpu storage donation. */
+	if (dmp.buff_len != uv_info.guest_cpu_stor_len)
+		return -EINVAL;
+
+	data = kvzalloc(uv_info.guest_cpu_stor_len, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	ret = kvm_s390_pv_dump_cpu(vcpu, data, &cmd->rc, &cmd->rrc);
+
+	VCPU_EVENT(vcpu, 3, "PROTVIRT DUMP CPU %d rc %x rrc %x",
+		   vcpu->vcpu_id, cmd->rc, cmd->rrc);
+
+	if (ret)
+		ret = -EINVAL;
+
+	/* On success copy over the dump data */
+	if (!ret && copy_to_user((__u8 __user *)dmp.buff_addr, data, uv_info.guest_cpu_stor_len))
+		ret = -EFAULT;
+
+	kvfree(data);
+	return ret;
+}
+
 long kvm_arch_vcpu_ioctl(struct file *filp,
 			 unsigned int ioctl, unsigned long arg)
 {
@@ -4955,7 +5406,7 @@
 		struct kvm_s390_mem_op mem_op;
 
 		if (copy_from_user(&mem_op, argp, sizeof(mem_op)) == 0)
-			r = kvm_s390_guest_memsida_op(vcpu, &mem_op);
+			r = kvm_s390_vcpu_memsida_op(vcpu, &mem_op);
 		else
 			r = -EFAULT;
 		break;
@@ -4994,6 +5445,33 @@
 					   irq_state.len);
 		break;
 	}
+	case KVM_S390_PV_CPU_COMMAND: {
+		struct kvm_pv_cmd cmd;
+
+		r = -EINVAL;
+		if (!is_prot_virt_host())
+			break;
+
+		r = -EFAULT;
+		if (copy_from_user(&cmd, argp, sizeof(cmd)))
+			break;
+
+		r = -EINVAL;
+		if (cmd.flags)
+			break;
+
+		/* We only handle this cmd right now */
+		if (cmd.cmd != KVM_PV_DUMP)
+			break;
+
+		r = kvm_s390_handle_pv_vcpu_dump(vcpu, &cmd);
+
+		/* Always copy over UV rc / rrc data */
+		if (copy_to_user((__u8 __user *)argp, &cmd.rc,
+				 sizeof(cmd.rc) + sizeof(cmd.rrc)))
+			r = -EFAULT;
+		break;
+	}
 	default:
 		r = -ENOTTY;
 	}
@@ -5038,6 +5516,23 @@
 	/* When we are protected, we should not change the memory slots */
 	if (kvm_s390_pv_get_handle(kvm))
 		return -EINVAL;
+
+	if (!kvm->arch.migration_mode)
+		return 0;
+
+	/*
+	 * Turn off migration mode when:
+	 * - userspace creates a new memslot with dirty logging off,
+	 * - userspace modifies an existing memslot (MOVE or FLAGS_ONLY) and
+	 *   dirty logging is turned off.
+	 * Migration mode expects dirty page logging being enabled to store
+	 * its dirty bitmap.
+	 */
+	if (change != KVM_MR_DELETE &&
+	    !(mem->flags & KVM_MEM_LOG_DIRTY_PAGES))
+		WARN(kvm_s390_vm_stop_migration(kvm),
+		     "Failed to stop migration mode");
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/kvm-s390.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/kvm-s390.h
@@ -119,6 +119,21 @@
 	return (base2 ? vcpu->run->s.regs.gprs[base2] : 0) + disp2;
 }
 
+static inline u64 kvm_s390_get_base_disp_siy(struct kvm_vcpu *vcpu, u8 *ar)
+{
+	u32 base1 = vcpu->arch.sie_block->ipb >> 28;
+	s64 disp1;
+
+	/* The displacement is a 20bit _SIGNED_ value */
+	disp1 = sign_extend64(((vcpu->arch.sie_block->ipb & 0x0fff0000) >> 16) +
+			      ((vcpu->arch.sie_block->ipb & 0xff00) << 4), 19);
+
+	if (ar)
+		*ar = base1;
+
+	return (base1 ? vcpu->run->s.regs.gprs[base1] : 0) + disp1;
+}
+
 static inline void kvm_s390_get_base_disp_sse(struct kvm_vcpu *vcpu,
 					      u64 *address1, u64 *address2,
 					      u8 *ar_b1, u8 *ar_b2)
@@ -208,6 +223,24 @@
 	return kvm->arch.user_cpu_state_ctrl != 0;
 }
 
+static inline void kvm_s390_set_user_cpu_state_ctrl(struct kvm *kvm)
+{
+	if (kvm->arch.user_cpu_state_ctrl)
+		return;
+
+	VM_EVENT(kvm, 3, "%s", "ENABLE: Userspace CPU state control");
+	kvm->arch.user_cpu_state_ctrl = 1;
+}
+
+static inline u32 kvm_s390_get_gisa_desc(struct kvm *kvm)
+{
+	u32 gd = (u32)(u64)kvm->arch.gisa_int.origin;
+
+	if (gd && sclp.has_gisaf)
+		gd |= GISA_FORMAT1;
+	return gd;
+}
+
 /* implemented in pv.c */
 int kvm_s390_pv_destroy_cpu(struct kvm_vcpu *vcpu, u16 *rc, u16 *rrc);
 int kvm_s390_pv_create_cpu(struct kvm_vcpu *vcpu, u16 *rc, u16 *rrc);
@@ -218,6 +251,11 @@
 int kvm_s390_pv_unpack(struct kvm *kvm, unsigned long addr, unsigned long size,
 		       unsigned long tweak, u16 *rc, u16 *rrc);
 int kvm_s390_pv_set_cpu_state(struct kvm_vcpu *vcpu, u8 state);
+int kvm_s390_pv_dump_cpu(struct kvm_vcpu *vcpu, void *buff, u16 *rc, u16 *rrc);
+int kvm_s390_pv_dump_stor_state(struct kvm *kvm, void __user *buff_user,
+				u64 *gaddr, u64 buff_user_len, u16 *rc, u16 *rrc);
+int kvm_s390_pv_dump_complete(struct kvm *kvm, void __user *buff_user,
+			      u16 *rc, u16 *rrc);
 
 static inline u64 kvm_s390_pv_get_handle(struct kvm *kvm)
 {
@@ -326,8 +364,7 @@
 int kvm_s390_handle_sigp_pei(struct kvm_vcpu *vcpu);
 
 /* implemented in kvm-s390.c */
-void kvm_s390_set_tod_clock(struct kvm *kvm,
-			    const struct kvm_s390_vm_tod_clock *gtod);
+int kvm_s390_try_set_tod_clock(struct kvm *kvm, const struct kvm_s390_vm_tod_clock *gtod);
 long kvm_arch_fault_in_page(struct kvm_vcpu *vcpu, gpa_t gpa, int writable);
 int kvm_s390_store_status_unloaded(struct kvm_vcpu *vcpu, unsigned long addr);
 int kvm_s390_vcpu_store_status(struct kvm_vcpu *vcpu, unsigned long addr);
@@ -418,6 +455,7 @@
 int kvm_s390_ext_call_pending(struct kvm_vcpu *vcpu);
 extern struct kvm_device_ops kvm_flic_ops;
 int kvm_s390_is_stop_irq_pending(struct kvm_vcpu *vcpu);
+int kvm_s390_is_restart_irq_pending(struct kvm_vcpu *vcpu);
 void kvm_s390_clear_stop_irq(struct kvm_vcpu *vcpu);
 int kvm_s390_set_irq_state(struct kvm_vcpu *vcpu,
 			   void __user *buf, int len);
@@ -426,6 +464,8 @@
 void kvm_s390_gisa_init(struct kvm *kvm);
 void kvm_s390_gisa_clear(struct kvm *kvm);
 void kvm_s390_gisa_destroy(struct kvm *kvm);
+void kvm_s390_gisa_disable(struct kvm *kvm);
+void kvm_s390_gisa_enable(struct kvm *kvm);
 int kvm_s390_gib_init(u8 nisc);
 void kvm_s390_gib_destroy(void);
 
@@ -473,6 +513,16 @@
 void kvm_s390_vcpu_crypto_reset_all(struct kvm *kvm);
 
 /**
+ * kvm_s390_vcpu_pci_enable_interp
+ *
+ * Set the associated PCI attributes for each vcpu to allow for zPCI Load/Store
+ * interpretation as well as adapter interruption forwarding.
+ *
+ * @kvm: the KVM guest
+ */
+void kvm_s390_vcpu_pci_enable_interp(struct kvm *kvm);
+
+/**
  * diag9c_forwarding_hz
  *
  * Set the maximum number of diag9c forwarding per second
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/pci.c
@@ -0,0 +1,702 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * s390 kvm PCI passthrough support
+ *
+ * Copyright IBM Corp. 2022
+ *
+ *    Author(s): Matthew Rosato <mjrosato@linux.ibm.com>
+ */
+
+#include <linux/kvm_host.h>
+#include <linux/pci.h>
+#include <asm/pci.h>
+#include <asm/pci_insn.h>
+#include <asm/pci_io.h>
+#include <asm/sclp.h>
+#include "pci.h"
+#include "kvm-s390.h"
+
+struct zpci_aift *aift;
+
+static inline int __set_irq_noiib(u16 ctl, u8 isc)
+{
+	union zpci_sic_iib iib = {{0}};
+
+	return zpci_set_irq_ctrl(ctl, isc, &iib);
+}
+
+void kvm_s390_pci_aen_exit(void)
+{
+	unsigned long flags;
+	struct kvm_zdev **gait_kzdev;
+
+	lockdep_assert_held(&aift->aift_lock);
+
+	/*
+	 * Contents of the aipb remain registered for the life of the host
+	 * kernel, the information preserved in zpci_aipb and zpci_aif_sbv
+	 * in case we insert the KVM module again later.  Clear the AIFT
+	 * information and free anything not registered with underlying
+	 * firmware.
+	 */
+	spin_lock_irqsave(&aift->gait_lock, flags);
+	gait_kzdev = aift->kzdev;
+	aift->gait = NULL;
+	aift->sbv = NULL;
+	aift->kzdev = NULL;
+	spin_unlock_irqrestore(&aift->gait_lock, flags);
+
+	kfree(gait_kzdev);
+}
+
+static int zpci_setup_aipb(u8 nisc)
+{
+	struct page *page;
+	int size, rc;
+
+	zpci_aipb = kzalloc(sizeof(union zpci_sic_iib), GFP_KERNEL);
+	if (!zpci_aipb)
+		return -ENOMEM;
+
+	aift->sbv = airq_iv_create(ZPCI_NR_DEVICES, AIRQ_IV_ALLOC, NULL);
+	if (!aift->sbv) {
+		rc = -ENOMEM;
+		goto free_aipb;
+	}
+	zpci_aif_sbv = aift->sbv;
+	size = get_order(PAGE_ALIGN(ZPCI_NR_DEVICES *
+						sizeof(struct zpci_gaite)));
+	page = alloc_pages(GFP_KERNEL | __GFP_ZERO, size);
+	if (!page) {
+		rc = -ENOMEM;
+		goto free_sbv;
+	}
+	aift->gait = (struct zpci_gaite *)page_to_virt(page);
+
+	zpci_aipb->aipb.faisb = virt_to_phys(aift->sbv->vector);
+	zpci_aipb->aipb.gait = virt_to_phys(aift->gait);
+	zpci_aipb->aipb.afi = nisc;
+	zpci_aipb->aipb.faal = ZPCI_NR_DEVICES;
+
+	/* Setup Adapter Event Notification Interpretation */
+	if (zpci_set_irq_ctrl(SIC_SET_AENI_CONTROLS, 0, zpci_aipb)) {
+		rc = -EIO;
+		goto free_gait;
+	}
+
+	return 0;
+
+free_gait:
+	free_pages((unsigned long)aift->gait, size);
+free_sbv:
+	airq_iv_release(aift->sbv);
+	zpci_aif_sbv = NULL;
+free_aipb:
+	kfree(zpci_aipb);
+	zpci_aipb = NULL;
+
+	return rc;
+}
+
+static int zpci_reset_aipb(u8 nisc)
+{
+	/*
+	 * AEN registration can only happen once per system boot.  If
+	 * an aipb already exists then AEN was already registered and
+	 * we can re-use the aipb contents.  This can only happen if
+	 * the KVM module was removed and re-inserted.  However, we must
+	 * ensure that the same forwarding ISC is used as this is assigned
+	 * during KVM module load.
+	 */
+	if (zpci_aipb->aipb.afi != nisc)
+		return -EINVAL;
+
+	aift->sbv = zpci_aif_sbv;
+	aift->gait = (struct zpci_gaite *)zpci_aipb->aipb.gait;
+
+	return 0;
+}
+
+int kvm_s390_pci_aen_init(u8 nisc)
+{
+	int rc = 0;
+
+	/* If already enabled for AEN, bail out now */
+	if (aift->gait || aift->sbv)
+		return -EPERM;
+
+	mutex_lock(&aift->aift_lock);
+	aift->kzdev = kcalloc(ZPCI_NR_DEVICES, sizeof(struct kvm_zdev),
+			      GFP_KERNEL);
+	if (!aift->kzdev) {
+		rc = -ENOMEM;
+		goto unlock;
+	}
+
+	if (!zpci_aipb)
+		rc = zpci_setup_aipb(nisc);
+	else
+		rc = zpci_reset_aipb(nisc);
+	if (rc)
+		goto free_zdev;
+
+	/* Enable floating IRQs */
+	if (__set_irq_noiib(SIC_IRQ_MODE_SINGLE, nisc)) {
+		rc = -EIO;
+		kvm_s390_pci_aen_exit();
+	}
+
+	goto unlock;
+
+free_zdev:
+	kfree(aift->kzdev);
+unlock:
+	mutex_unlock(&aift->aift_lock);
+	return rc;
+}
+
+/* Modify PCI: Register floating adapter interruption forwarding */
+static int kvm_zpci_set_airq(struct zpci_dev *zdev)
+{
+	u64 req = ZPCI_CREATE_REQ(zdev->fh, 0, ZPCI_MOD_FC_REG_INT);
+	struct zpci_fib fib = {};
+	u8 status;
+
+	fib.fmt0.isc = zdev->kzdev->fib.fmt0.isc;
+	fib.fmt0.sum = 1;       /* enable summary notifications */
+	fib.fmt0.noi = airq_iv_end(zdev->aibv);
+	fib.fmt0.aibv = virt_to_phys(zdev->aibv->vector);
+	fib.fmt0.aibvo = 0;
+	fib.fmt0.aisb = virt_to_phys(aift->sbv->vector + (zdev->aisb / 64) * 8);
+	fib.fmt0.aisbo = zdev->aisb & 63;
+	fib.gd = zdev->gisa;
+
+	return zpci_mod_fc(req, &fib, &status) ? -EIO : 0;
+}
+
+/* Modify PCI: Unregister floating adapter interruption forwarding */
+static int kvm_zpci_clear_airq(struct zpci_dev *zdev)
+{
+	u64 req = ZPCI_CREATE_REQ(zdev->fh, 0, ZPCI_MOD_FC_DEREG_INT);
+	struct zpci_fib fib = {};
+	u8 cc, status;
+
+	fib.gd = zdev->gisa;
+
+	cc = zpci_mod_fc(req, &fib, &status);
+	if (cc == 3 || (cc == 1 && status == 24))
+		/* Function already gone or IRQs already deregistered. */
+		cc = 0;
+
+	return cc ? -EIO : 0;
+}
+
+static inline void unaccount_mem(unsigned long nr_pages)
+{
+	struct user_struct *user = get_uid(current_user());
+
+	if (user)
+		atomic_long_sub(nr_pages, &user->locked_vm);
+	if (current->mm)
+		atomic64_sub(nr_pages, &current->mm->pinned_vm);
+}
+
+static inline int account_mem(unsigned long nr_pages)
+{
+	struct user_struct *user = get_uid(current_user());
+	unsigned long page_limit, cur_pages, new_pages;
+
+	page_limit = rlimit(RLIMIT_MEMLOCK) >> PAGE_SHIFT;
+
+	do {
+		cur_pages = atomic_long_read(&user->locked_vm);
+		new_pages = cur_pages + nr_pages;
+		if (new_pages > page_limit)
+			return -ENOMEM;
+	} while (atomic_long_cmpxchg(&user->locked_vm, cur_pages,
+					new_pages) != cur_pages);
+
+	atomic64_add(nr_pages, &current->mm->pinned_vm);
+
+	return 0;
+}
+
+static int kvm_s390_pci_aif_enable(struct zpci_dev *zdev, struct zpci_fib *fib,
+				   bool assist)
+{
+	struct page *pages[1], *aibv_page, *aisb_page = NULL;
+	unsigned int msi_vecs, idx;
+	struct zpci_gaite *gaite;
+	unsigned long hva, bit;
+	struct kvm *kvm;
+	phys_addr_t gaddr;
+	int rc = 0, gisc, npages, pcount = 0;
+
+	/*
+	 * Interrupt forwarding is only applicable if the device is already
+	 * enabled for interpretation
+	 */
+	if (zdev->gisa == 0)
+		return -EINVAL;
+
+	kvm = zdev->kzdev->kvm;
+	msi_vecs = min_t(unsigned int, fib->fmt0.noi, zdev->max_msi);
+
+	/* Get the associated forwarding ISC - if invalid, return the error */
+	gisc = kvm_s390_gisc_register(kvm, fib->fmt0.isc);
+	if (gisc < 0)
+		return gisc;
+
+	/* Replace AIBV address */
+	idx = srcu_read_lock(&kvm->srcu);
+	hva = gfn_to_hva(kvm, gpa_to_gfn((gpa_t)fib->fmt0.aibv));
+	npages = pin_user_pages_fast(hva, 1, FOLL_WRITE | FOLL_LONGTERM, pages);
+	srcu_read_unlock(&kvm->srcu, idx);
+	if (npages < 1) {
+		rc = -EIO;
+		goto out;
+	}
+	aibv_page = pages[0];
+	pcount++;
+	gaddr = page_to_phys(aibv_page) + (fib->fmt0.aibv & ~PAGE_MASK);
+	fib->fmt0.aibv = gaddr;
+
+	/* Pin the guest AISB if one was specified */
+	if (fib->fmt0.sum == 1) {
+		idx = srcu_read_lock(&kvm->srcu);
+		hva = gfn_to_hva(kvm, gpa_to_gfn((gpa_t)fib->fmt0.aisb));
+		npages = pin_user_pages_fast(hva, 1, FOLL_WRITE | FOLL_LONGTERM,
+					     pages);
+		srcu_read_unlock(&kvm->srcu, idx);
+		if (npages < 1) {
+			rc = -EIO;
+			goto unpin1;
+		}
+		aisb_page = pages[0];
+		pcount++;
+	}
+
+	/* Account for pinned pages, roll back on failure */
+	if (account_mem(pcount))
+		goto unpin2;
+
+	/* AISB must be allocated before we can fill in GAITE */
+	mutex_lock(&aift->aift_lock);
+	bit = airq_iv_alloc_bit(aift->sbv);
+	if (bit == -1UL)
+		goto unlock;
+	zdev->aisb = bit; /* store the summary bit number */
+	zdev->aibv = airq_iv_create(msi_vecs, AIRQ_IV_DATA |
+				    AIRQ_IV_BITLOCK |
+				    AIRQ_IV_GUESTVEC,
+				    phys_to_virt(fib->fmt0.aibv));
+
+	spin_lock_irq(&aift->gait_lock);
+	gaite = (struct zpci_gaite *)aift->gait + (zdev->aisb *
+						   sizeof(struct zpci_gaite));
+
+	/* If assist not requested, host will get all alerts */
+	if (assist)
+		gaite->gisa = (u32)virt_to_phys(&kvm->arch.sie_page2->gisa);
+	else
+		gaite->gisa = 0;
+
+	gaite->gisc = fib->fmt0.isc;
+	gaite->count++;
+	gaite->aisbo = fib->fmt0.aisbo;
+	gaite->aisb = virt_to_phys(page_address(aisb_page) + (fib->fmt0.aisb &
+							      ~PAGE_MASK));
+	aift->kzdev[zdev->aisb] = zdev->kzdev;
+	spin_unlock_irq(&aift->gait_lock);
+
+	/* Update guest FIB for re-issue */
+	fib->fmt0.aisbo = zdev->aisb & 63;
+	fib->fmt0.aisb = virt_to_phys(aift->sbv->vector + (zdev->aisb / 64) * 8);
+	fib->fmt0.isc = gisc;
+
+	/* Save some guest fib values in the host for later use */
+	zdev->kzdev->fib.fmt0.isc = fib->fmt0.isc;
+	zdev->kzdev->fib.fmt0.aibv = fib->fmt0.aibv;
+	mutex_unlock(&aift->aift_lock);
+
+	/* Issue the clp to setup the irq now */
+	rc = kvm_zpci_set_airq(zdev);
+	return rc;
+
+unlock:
+	mutex_unlock(&aift->aift_lock);
+unpin2:
+	if (fib->fmt0.sum == 1)
+		unpin_user_page(aisb_page);
+unpin1:
+	unpin_user_page(aibv_page);
+out:
+	return rc;
+}
+
+static int kvm_s390_pci_aif_disable(struct zpci_dev *zdev, bool force)
+{
+	struct kvm_zdev *kzdev = zdev->kzdev;
+	struct zpci_gaite *gaite;
+	struct page *vpage = NULL, *spage = NULL;
+	int rc, pcount = 0;
+	u8 isc;
+
+	if (zdev->gisa == 0)
+		return -EINVAL;
+
+	mutex_lock(&aift->aift_lock);
+
+	/*
+	 * If the clear fails due to an error, leave now unless we know this
+	 * device is about to go away (force) -- In that case clear the GAITE
+	 * regardless.
+	 */
+	rc = kvm_zpci_clear_airq(zdev);
+	if (rc && !force)
+		goto out;
+
+	if (zdev->kzdev->fib.fmt0.aibv == 0)
+		goto out;
+	spin_lock_irq(&aift->gait_lock);
+	gaite = (struct zpci_gaite *)aift->gait + (zdev->aisb *
+						   sizeof(struct zpci_gaite));
+	isc = gaite->gisc;
+	gaite->count--;
+	if (gaite->count == 0) {
+		/* Release guest AIBV and AISB */
+		vpage = phys_to_page(kzdev->fib.fmt0.aibv);
+		if (gaite->aisb != 0)
+			spage = phys_to_page(gaite->aisb);
+		/* Clear the GAIT entry */
+		gaite->aisb = 0;
+		gaite->gisc = 0;
+		gaite->aisbo = 0;
+		gaite->gisa = 0;
+		aift->kzdev[zdev->aisb] = NULL;
+		/* Clear zdev info */
+		airq_iv_free_bit(aift->sbv, zdev->aisb);
+		airq_iv_release(zdev->aibv);
+		zdev->aisb = 0;
+		zdev->aibv = NULL;
+	}
+	spin_unlock_irq(&aift->gait_lock);
+	kvm_s390_gisc_unregister(kzdev->kvm, isc);
+	kzdev->fib.fmt0.isc = 0;
+	kzdev->fib.fmt0.aibv = 0;
+
+	if (vpage) {
+		unpin_user_page(vpage);
+		pcount++;
+	}
+	if (spage) {
+		unpin_user_page(spage);
+		pcount++;
+	}
+	if (pcount > 0)
+		unaccount_mem(pcount);
+out:
+	mutex_unlock(&aift->aift_lock);
+
+	return rc;
+}
+
+static int kvm_s390_pci_dev_open(struct zpci_dev *zdev)
+{
+	struct kvm_zdev *kzdev;
+
+	kzdev = kzalloc(sizeof(struct kvm_zdev), GFP_KERNEL);
+	if (!kzdev)
+		return -ENOMEM;
+
+	kzdev->zdev = zdev;
+	zdev->kzdev = kzdev;
+
+	return 0;
+}
+
+static void kvm_s390_pci_dev_release(struct zpci_dev *zdev)
+{
+	struct kvm_zdev *kzdev;
+
+	kzdev = zdev->kzdev;
+	WARN_ON(kzdev->zdev != zdev);
+	zdev->kzdev = NULL;
+	kfree(kzdev);
+}
+
+
+/*
+ * Register device with the specified KVM. If interpetation facilities are
+ * available, enable them and let userspace indicate whether or not they will
+ * be used (specify SHM bit to disable).
+ */
+static int kvm_s390_pci_register_kvm(void *opaque, struct kvm *kvm)
+{
+	struct zpci_dev *zdev = opaque;
+	int rc;
+
+	if (!zdev)
+		return -EINVAL;
+
+	mutex_lock(&zdev->kzdev_lock);
+
+	if (zdev->kzdev || zdev->gisa != 0 || !kvm) {
+		mutex_unlock(&zdev->kzdev_lock);
+		return -EINVAL;
+	}
+
+	kvm_get_kvm(kvm);
+
+	mutex_lock(&kvm->lock);
+
+	rc = kvm_s390_pci_dev_open(zdev);
+	if (rc)
+		goto err;
+
+	/*
+	 * If interpretation facilities aren't available, add the device to
+	 * the kzdev list but don't enable for interpretation.
+	 */
+	if (!kvm_s390_pci_interp_allowed())
+		goto out;
+
+	/*
+	 * If this is the first request to use an interpreted device, make the
+	 * necessary vcpu changes
+	 */
+	if (!kvm->arch.use_zpci_interp)
+		kvm_s390_vcpu_pci_enable_interp(kvm);
+
+	if (zdev_enabled(zdev)) {
+		rc = zpci_disable_device(zdev);
+		if (rc)
+			goto err;
+	}
+
+	/*
+	 * Store information about the identity of the kvm guest allowed to
+	 * access this device via interpretation to be used by host CLP
+	 */
+	zdev->gisa = (u32)virt_to_phys(&kvm->arch.sie_page2->gisa);
+
+	rc = zpci_enable_device(zdev);
+	if (rc)
+		goto clear_gisa;
+
+	/* Re-register the IOMMU that was already created */
+	rc = zpci_register_ioat(zdev, 0, zdev->start_dma, zdev->end_dma,
+				virt_to_phys(zdev->dma_table));
+	if (rc)
+		goto clear_gisa;
+
+out:
+	zdev->kzdev->kvm = kvm;
+
+	spin_lock(&kvm->arch.kzdev_list_lock);
+	list_add_tail(&zdev->kzdev->entry, &kvm->arch.kzdev_list);
+	spin_unlock(&kvm->arch.kzdev_list_lock);
+
+	mutex_unlock(&kvm->lock);
+	mutex_unlock(&zdev->kzdev_lock);
+	return 0;
+
+clear_gisa:
+	zdev->gisa = 0;
+err:
+	if (zdev->kzdev)
+		kvm_s390_pci_dev_release(zdev);
+	mutex_unlock(&kvm->lock);
+	mutex_unlock(&zdev->kzdev_lock);
+	kvm_put_kvm(kvm);
+	return rc;
+}
+
+static void kvm_s390_pci_unregister_kvm(void *opaque)
+{
+	struct zpci_dev *zdev = opaque;
+	struct kvm *kvm;
+
+	if (!zdev)
+		return;
+
+	mutex_lock(&zdev->kzdev_lock);
+
+	if (WARN_ON(!zdev->kzdev)) {
+		mutex_unlock(&zdev->kzdev_lock);
+		return;
+	}
+
+	kvm = zdev->kzdev->kvm;
+	mutex_lock(&kvm->lock);
+
+	/*
+	 * A 0 gisa means interpretation was never enabled, just remove the
+	 * device from the list.
+	 */
+	if (zdev->gisa == 0)
+		goto out;
+
+	/* Forwarding must be turned off before interpretation */
+	if (zdev->kzdev->fib.fmt0.aibv != 0)
+		kvm_s390_pci_aif_disable(zdev, true);
+
+	/* Remove the host CLP guest designation */
+	zdev->gisa = 0;
+
+	if (zdev_enabled(zdev)) {
+		if (zpci_disable_device(zdev))
+			goto out;
+	}
+
+	if (zpci_enable_device(zdev))
+		goto out;
+
+	/* Re-register the IOMMU that was already created */
+	zpci_register_ioat(zdev, 0, zdev->start_dma, zdev->end_dma,
+			   virt_to_phys(zdev->dma_table));
+
+out:
+	spin_lock(&kvm->arch.kzdev_list_lock);
+	list_del(&zdev->kzdev->entry);
+	spin_unlock(&kvm->arch.kzdev_list_lock);
+	kvm_s390_pci_dev_release(zdev);
+
+	mutex_unlock(&kvm->lock);
+	mutex_unlock(&zdev->kzdev_lock);
+
+	kvm_put_kvm(kvm);
+}
+
+void kvm_s390_pci_init_list(struct kvm *kvm)
+{
+	spin_lock_init(&kvm->arch.kzdev_list_lock);
+	INIT_LIST_HEAD(&kvm->arch.kzdev_list);
+}
+
+void kvm_s390_pci_clear_list(struct kvm *kvm)
+{
+	/*
+	 * This list should already be empty, either via vfio device closures
+	 * or kvm fd cleanup.
+	 */
+	spin_lock(&kvm->arch.kzdev_list_lock);
+	WARN_ON_ONCE(!list_empty(&kvm->arch.kzdev_list));
+	spin_unlock(&kvm->arch.kzdev_list_lock);
+}
+
+static struct zpci_dev *get_zdev_from_kvm_by_fh(struct kvm *kvm, u32 fh)
+{
+	struct zpci_dev *zdev = NULL;
+	struct kvm_zdev *kzdev;
+
+	spin_lock(&kvm->arch.kzdev_list_lock);
+	list_for_each_entry(kzdev, &kvm->arch.kzdev_list, entry) {
+		if (kzdev->zdev->fh == fh) {
+			zdev = kzdev->zdev;
+			break;
+		}
+	}
+	spin_unlock(&kvm->arch.kzdev_list_lock);
+
+	return zdev;
+}
+
+static int kvm_s390_pci_zpci_reg_aen(struct zpci_dev *zdev,
+				     struct kvm_s390_zpci_op *args)
+{
+	struct zpci_fib fib = {};
+	bool hostflag;
+
+	fib.fmt0.aibv = args->u.reg_aen.ibv;
+	fib.fmt0.isc = args->u.reg_aen.isc;
+	fib.fmt0.noi = args->u.reg_aen.noi;
+	if (args->u.reg_aen.sb != 0) {
+		fib.fmt0.aisb = args->u.reg_aen.sb;
+		fib.fmt0.aisbo = args->u.reg_aen.sbo;
+		fib.fmt0.sum = 1;
+	} else {
+		fib.fmt0.aisb = 0;
+		fib.fmt0.aisbo = 0;
+		fib.fmt0.sum = 0;
+	}
+
+	hostflag = !(args->u.reg_aen.flags & KVM_S390_ZPCIOP_REGAEN_HOST);
+	return kvm_s390_pci_aif_enable(zdev, &fib, hostflag);
+}
+
+int kvm_s390_pci_zpci_op(struct kvm *kvm, struct kvm_s390_zpci_op *args)
+{
+	struct kvm_zdev *kzdev;
+	struct zpci_dev *zdev;
+	int r;
+
+	zdev = get_zdev_from_kvm_by_fh(kvm, args->fh);
+	if (!zdev)
+		return -ENODEV;
+
+	mutex_lock(&zdev->kzdev_lock);
+	mutex_lock(&kvm->lock);
+
+	kzdev = zdev->kzdev;
+	if (!kzdev) {
+		r = -ENODEV;
+		goto out;
+	}
+	if (kzdev->kvm != kvm) {
+		r = -EPERM;
+		goto out;
+	}
+
+	switch (args->op) {
+	case KVM_S390_ZPCIOP_REG_AEN:
+		/* Fail on unknown flags */
+		if (args->u.reg_aen.flags & ~KVM_S390_ZPCIOP_REGAEN_HOST) {
+			r = -EINVAL;
+			break;
+		}
+		r = kvm_s390_pci_zpci_reg_aen(zdev, args);
+		break;
+	case KVM_S390_ZPCIOP_DEREG_AEN:
+		r = kvm_s390_pci_aif_disable(zdev, false);
+		break;
+	default:
+		r = -EINVAL;
+	}
+
+out:
+	mutex_unlock(&kvm->lock);
+	mutex_unlock(&zdev->kzdev_lock);
+	return r;
+}
+
+int kvm_s390_pci_init(void)
+{
+	zpci_kvm_hook.kvm_register = kvm_s390_pci_register_kvm;
+	zpci_kvm_hook.kvm_unregister = kvm_s390_pci_unregister_kvm;
+
+	if (!kvm_s390_pci_interp_allowed())
+		return 0;
+
+	aift = kzalloc(sizeof(struct zpci_aift), GFP_KERNEL);
+	if (!aift)
+		return -ENOMEM;
+
+	spin_lock_init(&aift->gait_lock);
+	mutex_init(&aift->aift_lock);
+
+	return 0;
+}
+
+void kvm_s390_pci_exit(void)
+{
+	zpci_kvm_hook.kvm_register = NULL;
+	zpci_kvm_hook.kvm_unregister = NULL;
+
+	if (!kvm_s390_pci_interp_allowed())
+		return;
+
+	mutex_destroy(&aift->aift_lock);
+
+	kfree(aift);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/pci.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/pci.h
@@ -0,0 +1,88 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * s390 kvm PCI passthrough support
+ *
+ * Copyright IBM Corp. 2022
+ *
+ *    Author(s): Matthew Rosato <mjrosato@linux.ibm.com>
+ */
+
+#ifndef __KVM_S390_PCI_H
+#define __KVM_S390_PCI_H
+
+#include <linux/kvm_host.h>
+#include <linux/pci.h>
+#include <linux/mutex.h>
+#include <linux/kvm.h>
+#include <linux/kvm_host.h>
+#include <asm/airq.h>
+#include <asm/cpu.h>
+
+struct kvm_zdev {
+	struct zpci_dev *zdev;
+	struct kvm *kvm;
+	struct zpci_fib fib;
+	struct list_head entry;
+};
+
+struct zpci_gaite {
+	u32 gisa;
+	u8 gisc;
+	u8 count;
+	u8 reserved;
+	u8 aisbo;
+	u64 aisb;
+};
+
+struct zpci_aift {
+	struct zpci_gaite *gait;
+	struct airq_iv *sbv;
+	struct kvm_zdev **kzdev;
+	spinlock_t gait_lock; /* Protects the gait, used during AEN forward */
+	struct mutex aift_lock; /* Protects the other structures in aift */
+};
+
+extern struct zpci_aift *aift;
+
+static inline struct kvm *kvm_s390_pci_si_to_kvm(struct zpci_aift *aift,
+						 unsigned long si)
+{
+	if (!IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM) || !aift->kzdev ||
+	    !aift->kzdev[si])
+		return NULL;
+	return aift->kzdev[si]->kvm;
+};
+
+int kvm_s390_pci_aen_init(u8 nisc);
+void kvm_s390_pci_aen_exit(void);
+
+void kvm_s390_pci_init_list(struct kvm *kvm);
+void kvm_s390_pci_clear_list(struct kvm *kvm);
+
+int kvm_s390_pci_zpci_op(struct kvm *kvm, struct kvm_s390_zpci_op *args);
+
+int kvm_s390_pci_init(void);
+void kvm_s390_pci_exit(void);
+
+static inline bool kvm_s390_pci_interp_allowed(void)
+{
+	struct cpuid cpu_id;
+
+	get_cpu_id(&cpu_id);
+	switch (cpu_id.machine) {
+	case 0x2817:
+	case 0x2818:
+	case 0x2827:
+	case 0x2828:
+	case 0x2964:
+	case 0x2965:
+		/* No SHM on certain machines */
+		return false;
+	default:
+		return (IS_ENABLED(CONFIG_VFIO_PCI_ZDEV_KVM) &&
+			sclp.has_zpci_lsi && sclp.has_aeni && sclp.has_aisi &&
+			sclp.has_aisii);
+	}
+}
+
+#endif /* __KVM_S390_PCI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/priv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/priv.c
@@ -102,7 +102,20 @@
 		return kvm_s390_inject_prog_cond(vcpu, rc);
 
 	VCPU_EVENT(vcpu, 3, "SCK: setting guest TOD to 0x%llx", gtod.tod);
-	kvm_s390_set_tod_clock(vcpu->kvm, &gtod);
+	/*
+	 * To set the TOD clock the kvm lock must be taken, but the vcpu lock
+	 * is already held in handle_set_clock. The usual lock order is the
+	 * opposite.  As SCK is deprecated and should not be used in several
+	 * cases, for example when the multiple epoch facility or TOD clock
+	 * steering facility is installed (see Principles of Operation),  a
+	 * slow path can be used.  If the lock can not be taken via try_lock,
+	 * the instruction will be retried via -EAGAIN at a later point in
+	 * time.
+	 */
+	if (!kvm_s390_try_set_tod_clock(vcpu->kvm, &gtod)) {
+		kvm_s390_retry_instr(vcpu);
+		return -EAGAIN;
+	}
 
 	kvm_s390_set_psw_cc(vcpu, 0);
 	return 0;
@@ -397,6 +410,8 @@
 		mmap_read_unlock(current->mm);
 		if (rc == -EFAULT)
 			return kvm_s390_inject_program_int(vcpu, PGM_ADDRESSING);
+		if (rc == -EAGAIN)
+			continue;
 		if (rc < 0)
 			return rc;
 		start += PAGE_SIZE;
@@ -780,6 +795,36 @@
 	return 0;
 }
 
+static int handle_lpswey(struct kvm_vcpu *vcpu)
+{
+	psw_t new_psw;
+	u64 addr;
+	int rc;
+	u8 ar;
+
+	vcpu->stat.instruction_lpswey++;
+
+	if (!test_kvm_facility(vcpu->kvm, 193))
+		return kvm_s390_inject_program_int(vcpu, PGM_OPERATION);
+
+	if (vcpu->arch.sie_block->gpsw.mask & PSW_MASK_PSTATE)
+		return kvm_s390_inject_program_int(vcpu, PGM_PRIVILEGED_OP);
+
+	addr = kvm_s390_get_base_disp_siy(vcpu, &ar);
+	if (addr & 7)
+		return kvm_s390_inject_program_int(vcpu, PGM_SPECIFICATION);
+
+	rc = read_guest(vcpu, addr, ar, &new_psw, sizeof(new_psw));
+	if (rc)
+		return kvm_s390_inject_prog_cond(vcpu, rc);
+
+	vcpu->arch.sie_block->gpsw = new_psw;
+	if (!is_valid_psw(&vcpu->arch.sie_block->gpsw))
+		return kvm_s390_inject_program_int(vcpu, PGM_SPECIFICATION);
+
+	return 0;
+}
+
 static int handle_stidp(struct kvm_vcpu *vcpu)
 {
 	u64 stidp_data = vcpu->kvm->arch.model.cpuid;
@@ -1434,6 +1479,8 @@
 	case 0x61:
 	case 0x62:
 		return handle_ri(vcpu);
+	case 0x71:
+		return handle_lpswey(vcpu);
 	default:
 		return -EOPNOTSUPP;
 	}
@@ -1441,10 +1488,11 @@
 
 static int handle_tprot(struct kvm_vcpu *vcpu)
 {
-	u64 address1, address2;
-	unsigned long hva, gpa;
-	int ret = 0, cc = 0;
+	u64 address, operand2;
+	unsigned long gpa;
+	u8 access_key;
 	bool writable;
+	int ret, cc;
 	u8 ar;
 
 	vcpu->stat.instruction_tprot++;
@@ -1452,43 +1500,46 @@
 	if (vcpu->arch.sie_block->gpsw.mask & PSW_MASK_PSTATE)
 		return kvm_s390_inject_program_int(vcpu, PGM_PRIVILEGED_OP);
 
-	kvm_s390_get_base_disp_sse(vcpu, &address1, &address2, &ar, NULL);
+	kvm_s390_get_base_disp_sse(vcpu, &address, &operand2, &ar, NULL);
+	access_key = (operand2 & 0xf0) >> 4;
 
-	/* we only handle the Linux memory detection case:
-	 * access key == 0
-	 * everything else goes to userspace. */
-	if (address2 & 0xf0)
-		return -EOPNOTSUPP;
 	if (vcpu->arch.sie_block->gpsw.mask & PSW_MASK_DAT)
 		ipte_lock(vcpu);
-	ret = guest_translate_address(vcpu, address1, ar, &gpa, GACC_STORE);
-	if (ret == PGM_PROTECTION) {
+
+	ret = guest_translate_address_with_key(vcpu, address, ar, &gpa,
+					       GACC_STORE, access_key);
+	if (ret == 0) {
+		gfn_to_hva_prot(vcpu->kvm, gpa_to_gfn(gpa), &writable);
+	} else if (ret == PGM_PROTECTION) {
+		writable = false;
 		/* Write protected? Try again with read-only... */
-		cc = 1;
-		ret = guest_translate_address(vcpu, address1, ar, &gpa,
-					      GACC_FETCH);
+		ret = guest_translate_address_with_key(vcpu, address, ar, &gpa,
+						       GACC_FETCH, access_key);
 	}
-	if (ret) {
-		if (ret == PGM_ADDRESSING || ret == PGM_TRANSLATION_SPEC) {
-			ret = kvm_s390_inject_program_int(vcpu, ret);
-		} else if (ret > 0) {
-			/* Translation not available */
-			kvm_s390_set_psw_cc(vcpu, 3);
+	if (ret >= 0) {
+		cc = -1;
+
+		/* Fetching permitted; storing permitted */
+		if (ret == 0 && writable)
+			cc = 0;
+		/* Fetching permitted; storing not permitted */
+		else if (ret == 0 && !writable)
+			cc = 1;
+		/* Fetching not permitted; storing not permitted */
+		else if (ret == PGM_PROTECTION)
+			cc = 2;
+		/* Translation not available */
+		else if (ret != PGM_ADDRESSING && ret != PGM_TRANSLATION_SPEC)
+			cc = 3;
+
+		if (cc != -1) {
+			kvm_s390_set_psw_cc(vcpu, cc);
 			ret = 0;
+		} else {
+			ret = kvm_s390_inject_program_int(vcpu, ret);
 		}
-		goto out_unlock;
 	}
 
-	hva = gfn_to_hva_prot(vcpu->kvm, gpa_to_gfn(gpa), &writable);
-	if (kvm_is_error_hva(hva)) {
-		ret = kvm_s390_inject_program_int(vcpu, PGM_ADDRESSING);
-	} else {
-		if (!writable)
-			cc = 1;		/* Write not permitted ==> read-only */
-		kvm_s390_set_psw_cc(vcpu, cc);
-		/* Note: CC2 only occurs for storage keys (not supported yet) */
-	}
-out_unlock:
 	if (vcpu->arch.sie_block->gpsw.mask & PSW_MASK_DAT)
 		ipte_unlock(vcpu);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/pv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/pv.c
@@ -7,6 +7,7 @@
  */
 #include <linux/kvm.h>
 #include <linux/kvm_host.h>
+#include <linux/minmax.h>
 #include <linux/pagemap.h>
 #include <linux/sched/signal.h>
 #include <asm/gmap.h>
@@ -16,18 +17,17 @@
 
 int kvm_s390_pv_destroy_cpu(struct kvm_vcpu *vcpu, u16 *rc, u16 *rrc)
 {
-	int cc = 0;
+	int cc;
+
+	if (!kvm_s390_pv_cpu_get_handle(vcpu))
+		return 0;
+
+	cc = uv_cmd_nodata(kvm_s390_pv_cpu_get_handle(vcpu), UVC_CMD_DESTROY_SEC_CPU, rc, rrc);
+
+	KVM_UV_EVENT(vcpu->kvm, 3, "PROTVIRT DESTROY VCPU %d: rc %x rrc %x",
+		     vcpu->vcpu_id, *rc, *rrc);
+	WARN_ONCE(cc, "protvirt destroy cpu failed rc %x rrc %x", *rc, *rrc);
 
-	if (kvm_s390_pv_cpu_get_handle(vcpu)) {
-		cc = uv_cmd_nodata(kvm_s390_pv_cpu_get_handle(vcpu),
-				   UVC_CMD_DESTROY_SEC_CPU, rc, rrc);
-
-		KVM_UV_EVENT(vcpu->kvm, 3,
-			     "PROTVIRT DESTROY VCPU %d: rc %x rrc %x",
-			     vcpu->vcpu_id, *rc, *rrc);
-		WARN_ONCE(cc, "protvirt destroy cpu failed rc %x rrc %x",
-			  *rc, *rrc);
-	}
 	/* Intended memory leak for something that should never happen. */
 	if (!cc)
 		free_pages(vcpu->arch.pv.stor_base,
@@ -169,10 +169,13 @@
 	atomic_set(&kvm->mm->context.is_protected, 0);
 	KVM_UV_EVENT(kvm, 3, "PROTVIRT DESTROY VM: rc %x rrc %x", *rc, *rrc);
 	WARN_ONCE(cc, "protvirt destroy vm failed rc %x rrc %x", *rc, *rrc);
-	/* Inteded memory leak on "impossible" error */
-	if (!cc)
+	/* Intended memory leak on "impossible" error */
+	if (!cc) {
 		kvm_s390_pv_dealloc_vm(kvm);
-	return cc ? -EIO : 0;
+		return 0;
+	}
+	s390_replace_asce(kvm->arch.gmap);
+	return -EIO;
 }
 
 int kvm_s390_pv_init_vm(struct kvm *kvm, u16 *rc, u16 *rrc)
@@ -196,7 +199,7 @@
 	uvcb.conf_base_stor_origin = (u64)kvm->arch.pv.stor_base;
 	uvcb.conf_virt_stor_origin = (u64)kvm->arch.pv.stor_var;
 
-	cc = uv_call(0, (u64)&uvcb);
+	cc = uv_call_sched(0, (u64)&uvcb);
 	*rc = uvcb.header.rc;
 	*rrc = uvcb.header.rrc;
 	KVM_UV_EVENT(kvm, 3, "PROTVIRT CREATE VM: handle %llx len %llx rc %x rrc %x",
@@ -306,3 +309,200 @@
 		return -EINVAL;
 	return 0;
 }
+
+int kvm_s390_pv_dump_cpu(struct kvm_vcpu *vcpu, void *buff, u16 *rc, u16 *rrc)
+{
+	struct uv_cb_dump_cpu uvcb = {
+		.header.cmd = UVC_CMD_DUMP_CPU,
+		.header.len = sizeof(uvcb),
+		.cpu_handle = vcpu->arch.pv.handle,
+		.dump_area_origin = (u64)buff,
+	};
+	int cc;
+
+	cc = uv_call_sched(0, (u64)&uvcb);
+	*rc = uvcb.header.rc;
+	*rrc = uvcb.header.rrc;
+	return cc;
+}
+
+/* Size of the cache for the storage state dump data. 1MB for now */
+#define DUMP_BUFF_LEN HPAGE_SIZE
+
+/**
+ * kvm_s390_pv_dump_stor_state
+ *
+ * @kvm: pointer to the guest's KVM struct
+ * @buff_user: Userspace pointer where we will write the results to
+ * @gaddr: Starting absolute guest address for which the storage state
+ *	   is requested.
+ * @buff_user_len: Length of the buff_user buffer
+ * @rc: Pointer to where the uvcb return code is stored
+ * @rrc: Pointer to where the uvcb return reason code is stored
+ *
+ * Stores buff_len bytes of tweak component values to buff_user
+ * starting with the 1MB block specified by the absolute guest address
+ * (gaddr). The gaddr pointer will be updated with the last address
+ * for which data was written when returning to userspace. buff_user
+ * might be written to even if an error rc is returned. For instance
+ * if we encounter a fault after writing the first page of data.
+ *
+ * Context: kvm->lock needs to be held
+ *
+ * Return:
+ *  0 on success
+ *  -ENOMEM if allocating the cache fails
+ *  -EINVAL if gaddr is not aligned to 1MB
+ *  -EINVAL if buff_user_len is not aligned to uv_info.conf_dump_storage_state_len
+ *  -EINVAL if the UV call fails, rc and rrc will be set in this case
+ *  -EFAULT if copying the result to buff_user failed
+ */
+int kvm_s390_pv_dump_stor_state(struct kvm *kvm, void __user *buff_user,
+				u64 *gaddr, u64 buff_user_len, u16 *rc, u16 *rrc)
+{
+	struct uv_cb_dump_stor_state uvcb = {
+		.header.cmd = UVC_CMD_DUMP_CONF_STOR_STATE,
+		.header.len = sizeof(uvcb),
+		.config_handle = kvm->arch.pv.handle,
+		.gaddr = *gaddr,
+		.dump_area_origin = 0,
+	};
+	const u64 increment_len = uv_info.conf_dump_storage_state_len;
+	size_t buff_kvm_size;
+	size_t size_done = 0;
+	u8 *buff_kvm = NULL;
+	int cc, ret;
+
+	ret = -EINVAL;
+	/* UV call processes 1MB guest storage chunks at a time */
+	if (!IS_ALIGNED(*gaddr, HPAGE_SIZE))
+		goto out;
+
+	/*
+	 * We provide the storage state for 1MB chunks of guest
+	 * storage. The buffer will need to be aligned to
+	 * conf_dump_storage_state_len so we don't end on a partial
+	 * chunk.
+	 */
+	if (!buff_user_len ||
+	    !IS_ALIGNED(buff_user_len, increment_len))
+		goto out;
+
+	/*
+	 * Allocate a buffer from which we will later copy to the user
+	 * process. We don't want userspace to dictate our buffer size
+	 * so we limit it to DUMP_BUFF_LEN.
+	 */
+	ret = -ENOMEM;
+	buff_kvm_size = min_t(u64, buff_user_len, DUMP_BUFF_LEN);
+	buff_kvm = vzalloc(buff_kvm_size);
+	if (!buff_kvm)
+		goto out;
+
+	ret = 0;
+	uvcb.dump_area_origin = (u64)buff_kvm;
+	/* We will loop until the user buffer is filled or an error occurs */
+	do {
+		/* Get 1MB worth of guest storage state data */
+		cc = uv_call_sched(0, (u64)&uvcb);
+
+		/* All or nothing */
+		if (cc) {
+			ret = -EINVAL;
+			break;
+		}
+
+		size_done += increment_len;
+		uvcb.dump_area_origin += increment_len;
+		buff_user_len -= increment_len;
+		uvcb.gaddr += HPAGE_SIZE;
+
+		/* KVM Buffer full, time to copy to the process */
+		if (!buff_user_len || size_done == DUMP_BUFF_LEN) {
+			if (copy_to_user(buff_user, buff_kvm, size_done)) {
+				ret = -EFAULT;
+				break;
+			}
+
+			buff_user += size_done;
+			size_done = 0;
+			uvcb.dump_area_origin = (u64)buff_kvm;
+		}
+	} while (buff_user_len);
+
+	/* Report back where we ended dumping */
+	*gaddr = uvcb.gaddr;
+
+	/* Lets only log errors, we don't want to spam */
+out:
+	if (ret)
+		KVM_UV_EVENT(kvm, 3,
+			     "PROTVIRT DUMP STORAGE STATE: addr %llx ret %d, uvcb rc %x rrc %x",
+			     uvcb.gaddr, ret, uvcb.header.rc, uvcb.header.rrc);
+	*rc = uvcb.header.rc;
+	*rrc = uvcb.header.rrc;
+	vfree(buff_kvm);
+
+	return ret;
+}
+
+/**
+ * kvm_s390_pv_dump_complete
+ *
+ * @kvm: pointer to the guest's KVM struct
+ * @buff_user: Userspace pointer where we will write the results to
+ * @rc: Pointer to where the uvcb return code is stored
+ * @rrc: Pointer to where the uvcb return reason code is stored
+ *
+ * Completes the dumping operation and writes the completion data to
+ * user space.
+ *
+ * Context: kvm->lock needs to be held
+ *
+ * Return:
+ *  0 on success
+ *  -ENOMEM if allocating the completion buffer fails
+ *  -EINVAL if the UV call fails, rc and rrc will be set in this case
+ *  -EFAULT if copying the result to buff_user failed
+ */
+int kvm_s390_pv_dump_complete(struct kvm *kvm, void __user *buff_user,
+			      u16 *rc, u16 *rrc)
+{
+	struct uv_cb_dump_complete complete = {
+		.header.len = sizeof(complete),
+		.header.cmd = UVC_CMD_DUMP_COMPLETE,
+		.config_handle = kvm_s390_pv_get_handle(kvm),
+	};
+	u64 *compl_data;
+	int ret;
+
+	/* Allocate dump area */
+	compl_data = vzalloc(uv_info.conf_dump_finalize_len);
+	if (!compl_data)
+		return -ENOMEM;
+	complete.dump_area_origin = (u64)compl_data;
+
+	ret = uv_call_sched(0, (u64)&complete);
+	*rc = complete.header.rc;
+	*rrc = complete.header.rrc;
+	KVM_UV_EVENT(kvm, 3, "PROTVIRT DUMP COMPLETE: rc %x rrc %x",
+		     complete.header.rc, complete.header.rrc);
+
+	if (!ret) {
+		/*
+		 * kvm_s390_pv_dealloc_vm() will also (mem)set
+		 * this to false on a reboot or other destroy
+		 * operation for this vm.
+		 */
+		kvm->arch.pv.dumping = false;
+		kvm_s390_vcpu_unblock_all(kvm);
+		ret = copy_to_user(buff_user, compl_data, uv_info.conf_dump_finalize_len);
+		if (ret)
+			ret = -EFAULT;
+	}
+	vfree(compl_data);
+	/* If the UVC returned an error, translate it to -EINVAL */
+	if (ret > 0)
+		ret = -EINVAL;
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/sigp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/sigp.c
@@ -151,22 +151,10 @@
 static int __sigp_set_arch(struct kvm_vcpu *vcpu, u32 parameter,
 			   u64 *status_reg)
 {
-	unsigned int i;
-	struct kvm_vcpu *v;
-	bool all_stopped = true;
-
-	kvm_for_each_vcpu(i, v, vcpu->kvm) {
-		if (v == vcpu)
-			continue;
-		if (!is_vcpu_stopped(v))
-			all_stopped = false;
-	}
-
 	*status_reg &= 0xffffffff00000000UL;
 
 	/* Reject set arch order, with czam we're always in z/Arch mode. */
-	*status_reg |= (all_stopped ? SIGP_STATUS_INVALID_PARAMETER :
-					SIGP_STATUS_INCORRECT_STATE);
+	*status_reg |= SIGP_STATUS_INVALID_PARAMETER;
 	return SIGP_CC_STATUS_STORED;
 }
 
@@ -288,6 +276,34 @@
 	if (!dst_vcpu)
 		return SIGP_CC_NOT_OPERATIONAL;
 
+	/*
+	 * SIGP RESTART, SIGP STOP, and SIGP STOP AND STORE STATUS orders
+	 * are processed asynchronously. Until the affected VCPU finishes
+	 * its work and calls back into KVM to clear the (RESTART or STOP)
+	 * interrupt, we need to return any new non-reset orders "busy".
+	 *
+	 * This is important because a single VCPU could issue:
+	 *  1) SIGP STOP $DESTINATION
+	 *  2) SIGP SENSE $DESTINATION
+	 *
+	 * If the SIGP SENSE would not be rejected as "busy", it could
+	 * return an incorrect answer as to whether the VCPU is STOPPED
+	 * or OPERATING.
+	 */
+	if (order_code != SIGP_INITIAL_CPU_RESET &&
+	    order_code != SIGP_CPU_RESET) {
+		/*
+		 * Lockless check. Both SIGP STOP and SIGP (RE)START
+		 * properly synchronize everything while processing
+		 * their orders, while the guest cannot observe a
+		 * difference when issuing other orders from two
+		 * different VCPUs.
+		 */
+		if (kvm_s390_is_stop_irq_pending(dst_vcpu) ||
+		    kvm_s390_is_restart_irq_pending(dst_vcpu))
+			return SIGP_CC_BUSY;
+	}
+
 	switch (order_code) {
 	case SIGP_SENSE:
 		vcpu->stat.instruction_sigp_sense++;
@@ -464,9 +480,9 @@
 	struct kvm_vcpu *dest_vcpu;
 	u8 order_code = kvm_s390_get_base_disp_rs(vcpu, NULL);
 
-	trace_kvm_s390_handle_sigp_pei(vcpu, order_code, cpu_addr);
-
 	if (order_code == SIGP_EXTERNAL_CALL) {
+		trace_kvm_s390_handle_sigp_pei(vcpu, order_code, cpu_addr);
+
 		dest_vcpu = kvm_get_vcpu_by_id(vcpu->kvm, cpu_addr);
 		BUG_ON(dest_vcpu == NULL);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/kvm/vsie.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/kvm/vsie.c
@@ -169,7 +169,8 @@
 			    sizeof(struct kvm_s390_apcb0)))
 		return -EFAULT;
 
-	bitmap_and(apcb_s, apcb_s, apcb_h, sizeof(struct kvm_s390_apcb0));
+	bitmap_and(apcb_s, apcb_s, apcb_h,
+		   BITS_PER_BYTE * sizeof(struct kvm_s390_apcb0));
 
 	return 0;
 }
@@ -191,7 +192,8 @@
 			    sizeof(struct kvm_s390_apcb1)))
 		return -EFAULT;
 
-	bitmap_and(apcb_s, apcb_s, apcb_h, sizeof(struct kvm_s390_apcb1));
+	bitmap_and(apcb_s, apcb_s, apcb_h,
+		   BITS_PER_BYTE * sizeof(struct kvm_s390_apcb1));
 
 	return 0;
 }
@@ -538,8 +540,10 @@
 	if (test_kvm_cpu_feat(vcpu->kvm, KVM_S390_VM_CPU_FEAT_CEI))
 		scb_s->eca |= scb_o->eca & ECA_CEI;
 	/* Epoch Extension */
-	if (test_kvm_facility(vcpu->kvm, 139))
+	if (test_kvm_facility(vcpu->kvm, 139)) {
 		scb_s->ecd |= scb_o->ecd & ECD_MEF;
+		scb_s->epdx = scb_o->epdx;
+	}
 
 	/* etoken */
 	if (test_kvm_facility(vcpu->kvm, 156))
@@ -1202,7 +1206,6 @@
 	gmap = gmap_shadow(vcpu->arch.gmap, asce, edat);
 	if (IS_ERR(gmap))
 		return PTR_ERR(gmap);
-	gmap->private = vcpu->kvm;
 	WRITE_ONCE(vsie_page->gmap, gmap);
 	return 0;
 }
@@ -1317,8 +1320,14 @@
 	page = radix_tree_lookup(&kvm->arch.vsie.addr_to_page, addr >> 9);
 	rcu_read_unlock();
 	if (page) {
-		if (page_ref_inc_return(page) == 2)
-			return page_to_virt(page);
+		if (page_ref_inc_return(page) == 2) {
+			if (page->index == addr)
+				return page_to_virt(page);
+			/*
+			 * We raced with someone reusing + putting this vsie
+			 * page before we grabbed it.
+			 */
+		}
 		page_ref_dec(page);
 	}
 
@@ -1348,15 +1357,20 @@
 			kvm->arch.vsie.next++;
 			kvm->arch.vsie.next %= nr_vcpus;
 		}
-		radix_tree_delete(&kvm->arch.vsie.addr_to_page, page->index >> 9);
+		if (page->index != ULONG_MAX)
+			radix_tree_delete(&kvm->arch.vsie.addr_to_page,
+					  page->index >> 9);
 	}
-	page->index = addr;
-	/* double use of the same address */
+	/* Mark it as invalid until it resides in the tree. */
+	page->index = ULONG_MAX;
+
+	/* Double use of the same address or allocation failure. */
 	if (radix_tree_insert(&kvm->arch.vsie.addr_to_page, addr >> 9, page)) {
 		page_ref_dec(page);
 		mutex_unlock(&kvm->arch.vsie.mutex);
 		return NULL;
 	}
+	page->index = addr;
 	mutex_unlock(&kvm->arch.vsie.mutex);
 
 	vsie_page = page_to_virt(page);
@@ -1449,7 +1463,9 @@
 		vsie_page = page_to_virt(page);
 		release_gmap_shadow(vsie_page);
 		/* free the radix tree entry */
-		radix_tree_delete(&kvm->arch.vsie.addr_to_page, page->index >> 9);
+		if (page->index != ULONG_MAX)
+			radix_tree_delete(&kvm->arch.vsie.addr_to_page,
+					  page->index >> 9);
 		__free_page(page);
 	}
 	kvm->arch.vsie.page_count = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/lib/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/lib/Makefile
@@ -16,3 +16,5 @@
 CFLAGS_test_unwind.o += -fno-optimize-sibling-calls
 
 lib-$(CONFIG_FUNCTION_ERROR_INJECTION) += error-inject.o
+
+obj-$(CONFIG_EXPOLINE_EXTERN) += expoline/
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/lib/expoline/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/lib/expoline/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-y += expoline.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/lib/expoline/expoline.S
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/lib/expoline/expoline.S
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#include <asm/nospec-insn.h>
+#include <linux/linkage.h>
+
+.macro GEN_ALL_BR_THUNK_EXTERN
+	.irp r1,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	GEN_BR_THUNK_EXTERN %r\r1
+	.endr
+.endm
+
+GEN_ALL_BR_THUNK_EXTERN
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/lib/test_unwind.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/lib/test_unwind.c
@@ -171,10 +171,11 @@
 		}
 
 		/*
-		 * trigger specification exception
+		 * Trigger operation exception; use insn notation to bypass
+		 * llvm's integrated assembler sanity checks.
 		 */
 		asm volatile(
-			"	mvcl	%%r1,%%r1\n"
+			"	.insn	e,0x0000\n"	/* illegal opcode */
 			"0:	nopr	%%r7\n"
 			EX_TABLE(0b, 0b)
 			:);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/lib/uaccess.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/lib/uaccess.c
@@ -59,13 +59,19 @@
 #endif
 
 static inline unsigned long copy_from_user_mvcos(void *x, const void __user *ptr,
-						 unsigned long size)
+						 unsigned long size, unsigned long key)
 {
 	unsigned long tmp1, tmp2;
+	union oac spec = {
+		.oac2.key = key,
+		.oac2.as = PSW_BITS_AS_SECONDARY,
+		.oac2.k = 1,
+		.oac2.a = 1,
+	};
 
 	tmp1 = -4096UL;
 	asm volatile(
-		"   lghi  0,%[spec]\n"
+		"   lr	  0,%[spec]\n"
 		"0: .insn ss,0xc80000000000,0(%0,%2),0(%1),0\n"
 		"6: jz    4f\n"
 		"1: algr  %0,%3\n"
@@ -84,25 +90,25 @@
 		"5:\n"
 		EX_TABLE(0b,2b) EX_TABLE(3b,5b) EX_TABLE(6b,2b) EX_TABLE(7b,5b)
 		: "+a" (size), "+a" (ptr), "+a" (x), "+a" (tmp1), "=a" (tmp2)
-		: [spec] "K" (0x81UL)
+		: [spec] "d" (spec.val)
 		: "cc", "memory", "0");
 	return size;
 }
 
 static inline unsigned long copy_from_user_mvcp(void *x, const void __user *ptr,
-						unsigned long size)
+						unsigned long size, unsigned long key)
 {
 	unsigned long tmp1, tmp2;
 
 	tmp1 = -256UL;
 	asm volatile(
 		"   sacf  0\n"
-		"0: mvcp  0(%0,%2),0(%1),%3\n"
+		"0: mvcp  0(%0,%2),0(%1),%[key]\n"
 		"7: jz    5f\n"
 		"1: algr  %0,%3\n"
 		"   la    %1,256(%1)\n"
 		"   la    %2,256(%2)\n"
-		"2: mvcp  0(%0,%2),0(%1),%3\n"
+		"2: mvcp  0(%0,%2),0(%1),%[key]\n"
 		"8: jnz   1b\n"
 		"   j     5f\n"
 		"3: la    %4,255(%1)\n"	/* %4 = ptr + 255 */
@@ -111,7 +117,7 @@
 		"   slgr  %4,%1\n"
 		"   clgr  %0,%4\n"	/* copy crosses next page boundary? */
 		"   jnh   6f\n"
-		"4: mvcp  0(%4,%2),0(%1),%3\n"
+		"4: mvcp  0(%4,%2),0(%1),%[key]\n"
 		"9: slgr  %0,%4\n"
 		"   j     6f\n"
 		"5: slgr  %0,%0\n"
@@ -119,26 +125,55 @@
 		EX_TABLE(0b,3b) EX_TABLE(2b,3b) EX_TABLE(4b,6b)
 		EX_TABLE(7b,3b) EX_TABLE(8b,3b) EX_TABLE(9b,6b)
 		: "+a" (size), "+a" (ptr), "+a" (x), "+a" (tmp1), "=a" (tmp2)
-		: : "cc", "memory");
+		: [key] "d" (key << 4)
+		: "cc", "memory");
 	return size;
 }
 
-unsigned long raw_copy_from_user(void *to, const void __user *from, unsigned long n)
+static unsigned long raw_copy_from_user_key(void *to, const void __user *from,
+					    unsigned long n, unsigned long key)
 {
 	if (copy_with_mvcos())
-		return copy_from_user_mvcos(to, from, n);
-	return copy_from_user_mvcp(to, from, n);
+		return copy_from_user_mvcos(to, from, n, key);
+	return copy_from_user_mvcp(to, from, n, key);
+}
+
+unsigned long raw_copy_from_user(void *to, const void __user *from, unsigned long n)
+{
+	return raw_copy_from_user_key(to, from, n, 0);
 }
 EXPORT_SYMBOL(raw_copy_from_user);
 
+unsigned long _copy_from_user_key(void *to, const void __user *from,
+				  unsigned long n, unsigned long key)
+{
+	unsigned long res = n;
+
+	might_fault();
+	if (!should_fail_usercopy()) {
+		instrument_copy_from_user(to, from, n);
+		res = raw_copy_from_user_key(to, from, n, key);
+	}
+	if (unlikely(res))
+		memset(to + (n - res), 0, res);
+	return res;
+}
+EXPORT_SYMBOL(_copy_from_user_key);
+
 static inline unsigned long copy_to_user_mvcos(void __user *ptr, const void *x,
-					       unsigned long size)
+					       unsigned long size, unsigned long key)
 {
 	unsigned long tmp1, tmp2;
+	union oac spec = {
+		.oac1.key = key,
+		.oac1.as = PSW_BITS_AS_SECONDARY,
+		.oac1.k = 1,
+		.oac1.a = 1,
+	};
 
 	tmp1 = -4096UL;
 	asm volatile(
-		"   llilh 0,%[spec]\n"
+		"   lr	  0,%[spec]\n"
 		"0: .insn ss,0xc80000000000,0(%0,%1),0(%2),0\n"
 		"6: jz    4f\n"
 		"1: algr  %0,%3\n"
@@ -157,25 +192,25 @@
 		"5:\n"
 		EX_TABLE(0b,2b) EX_TABLE(3b,5b) EX_TABLE(6b,2b) EX_TABLE(7b,5b)
 		: "+a" (size), "+a" (ptr), "+a" (x), "+a" (tmp1), "=a" (tmp2)
-		: [spec] "K" (0x81UL)
+		: [spec] "d" (spec.val)
 		: "cc", "memory", "0");
 	return size;
 }
 
 static inline unsigned long copy_to_user_mvcs(void __user *ptr, const void *x,
-					      unsigned long size)
+					      unsigned long size, unsigned long key)
 {
 	unsigned long tmp1, tmp2;
 
 	tmp1 = -256UL;
 	asm volatile(
 		"   sacf  0\n"
-		"0: mvcs  0(%0,%1),0(%2),%3\n"
+		"0: mvcs  0(%0,%1),0(%2),%[key]\n"
 		"7: jz    5f\n"
 		"1: algr  %0,%3\n"
 		"   la    %1,256(%1)\n"
 		"   la    %2,256(%2)\n"
-		"2: mvcs  0(%0,%1),0(%2),%3\n"
+		"2: mvcs  0(%0,%1),0(%2),%[key]\n"
 		"8: jnz   1b\n"
 		"   j     5f\n"
 		"3: la    %4,255(%1)\n" /* %4 = ptr + 255 */
@@ -184,7 +219,7 @@
 		"   slgr  %4,%1\n"
 		"   clgr  %0,%4\n"	/* copy crosses next page boundary? */
 		"   jnh   6f\n"
-		"4: mvcs  0(%4,%1),0(%2),%3\n"
+		"4: mvcs  0(%4,%1),0(%2),%[key]\n"
 		"9: slgr  %0,%4\n"
 		"   j     6f\n"
 		"5: slgr  %0,%0\n"
@@ -192,27 +227,49 @@
 		EX_TABLE(0b,3b) EX_TABLE(2b,3b) EX_TABLE(4b,6b)
 		EX_TABLE(7b,3b) EX_TABLE(8b,3b) EX_TABLE(9b,6b)
 		: "+a" (size), "+a" (ptr), "+a" (x), "+a" (tmp1), "=a" (tmp2)
-		: : "cc", "memory");
+		: [key] "d" (key << 4)
+		: "cc", "memory");
 	return size;
 }
 
-unsigned long raw_copy_to_user(void __user *to, const void *from, unsigned long n)
+static unsigned long raw_copy_to_user_key(void __user *to, const void *from,
+					  unsigned long n, unsigned long key)
 {
 	if (copy_with_mvcos())
-		return copy_to_user_mvcos(to, from, n);
-	return copy_to_user_mvcs(to, from, n);
+		return copy_to_user_mvcos(to, from, n, key);
+	return copy_to_user_mvcs(to, from, n, key);
+}
+
+unsigned long raw_copy_to_user(void __user *to, const void *from, unsigned long n)
+{
+	return raw_copy_to_user_key(to, from, n, 0);
 }
 EXPORT_SYMBOL(raw_copy_to_user);
 
+unsigned long _copy_to_user_key(void __user *to, const void *from,
+				unsigned long n, unsigned long key)
+{
+	might_fault();
+	if (should_fail_usercopy())
+		return n;
+	instrument_copy_to_user(to, from, n);
+	return raw_copy_to_user_key(to, from, n, key);
+}
+EXPORT_SYMBOL(_copy_to_user_key);
+
 static inline unsigned long clear_user_mvcos(void __user *to, unsigned long size)
 {
 	unsigned long tmp1, tmp2;
+	union oac spec = {
+		.oac1.as = PSW_BITS_AS_SECONDARY,
+		.oac1.a = 1,
+	};
 
 	tmp1 = -4096UL;
 	asm volatile(
-		"   llilh 0,%[spec]\n"
+		"   lr	  0,%[spec]\n"
 		"0: .insn ss,0xc80000000000,0(%0,%1),0(%4),0\n"
-		"   jz	  4f\n"
+		"6: jz	  4f\n"
 		"1: algr  %0,%2\n"
 		"   slgr  %1,%2\n"
 		"   j	  0b\n"
@@ -222,13 +279,13 @@
 		"   clgr  %0,%3\n"	/* copy crosses next page boundary? */
 		"   jnh	  5f\n"
 		"3: .insn ss,0xc80000000000,0(%3,%1),0(%4),0\n"
-		"   slgr  %0,%3\n"
+		"7: slgr  %0,%3\n"
 		"   j	  5f\n"
 		"4: slgr  %0,%0\n"
 		"5:\n"
-		EX_TABLE(0b,2b) EX_TABLE(3b,5b)
-		: "+a" (size), "+a" (to), "+a" (tmp1), "=a" (tmp2)
-		: "a" (empty_zero_page), [spec] "K" (0x81UL)
+		EX_TABLE(0b,2b) EX_TABLE(6b,2b) EX_TABLE(3b,5b) EX_TABLE(7b,5b)
+		: "+&a" (size), "+&a" (to), "+a" (tmp1), "=&a" (tmp2)
+		: "a" (empty_zero_page), [spec] "d" (spec.val)
 		: "cc", "memory", "0");
 	return size;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/cmm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/cmm.c
@@ -95,11 +95,12 @@
 		(*counter)++;
 		spin_unlock(&cmm_lock);
 		nr--;
+		cond_resched();
 	}
 	return nr;
 }
 
-static long cmm_free_pages(long nr, long *counter, struct cmm_page_array **list)
+static long __cmm_free_pages(long nr, long *counter, struct cmm_page_array **list)
 {
 	struct cmm_page_array *pa;
 	unsigned long addr;
@@ -123,6 +124,21 @@
 	return nr;
 }
 
+static long cmm_free_pages(long nr, long *counter, struct cmm_page_array **list)
+{
+	long inc = 0;
+
+	while (nr) {
+		inc = min(256L, nr);
+		nr -= inc;
+		inc = __cmm_free_pages(inc, counter, list);
+		if (inc)
+			break;
+		cond_resched();
+	}
+	return nr + inc;
+}
+
 static int cmm_oom_notify(struct notifier_block *self,
 			  unsigned long dummy, void *parm)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/extmem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/extmem.c
@@ -289,15 +289,17 @@
 
 /*
  * real segment loading function, called from segment_load
+ * Must return either an error code < 0, or the segment type code >= 0
  */
 static int
 __segment_load (char *name, int do_nonshared, unsigned long *addr, unsigned long *end)
 {
 	unsigned long start_addr, end_addr, dummy;
 	struct dcss_segment *seg;
-	int rc, diag_cc;
+	int rc, diag_cc, segtype;
 
 	start_addr = end_addr = 0;
+	segtype = -1;
 	seg = kmalloc(sizeof(*seg), GFP_KERNEL | GFP_DMA);
 	if (seg == NULL) {
 		rc = -ENOMEM;
@@ -326,9 +328,9 @@
 	seg->res_name[8] = '\0';
 	strlcat(seg->res_name, " (DCSS)", sizeof(seg->res_name));
 	seg->res->name = seg->res_name;
-	rc = seg->vm_segtype;
-	if (rc == SEG_TYPE_SC ||
-	    ((rc == SEG_TYPE_SR || rc == SEG_TYPE_ER) && !do_nonshared))
+	segtype = seg->vm_segtype;
+	if (segtype == SEG_TYPE_SC ||
+	    ((segtype == SEG_TYPE_SR || segtype == SEG_TYPE_ER) && !do_nonshared))
 		seg->res->flags |= IORESOURCE_READONLY;
 
 	/* Check for overlapping resources before adding the mapping. */
@@ -386,7 +388,7 @@
  out_free:
 	kfree(seg);
  out:
-	return rc;
+	return rc < 0 ? rc : segtype;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/fault.c
@@ -397,7 +397,9 @@
 	flags = FAULT_FLAG_DEFAULT;
 	if (user_mode(regs))
 		flags |= FAULT_FLAG_USER;
-	if (access == VM_WRITE || is_write)
+	if (is_write)
+		access = VM_WRITE;
+	if (access == VM_WRITE)
 		flags |= FAULT_FLAG_WRITE;
 	mmap_read_lock(mm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/gmap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/gmap.c
@@ -672,6 +672,7 @@
  */
 void __gmap_zap(struct gmap *gmap, unsigned long gaddr)
 {
+	struct vm_area_struct *vma;
 	unsigned long vmaddr;
 	spinlock_t *ptl;
 	pte_t *ptep;
@@ -681,11 +682,17 @@
 						   gaddr >> PMD_SHIFT);
 	if (vmaddr) {
 		vmaddr |= gaddr & ~PMD_MASK;
+
+		vma = vma_lookup(gmap->mm, vmaddr);
+		if (!vma || is_vm_hugetlb_page(vma))
+			return;
+
 		/* Get pointer to the page table entry */
 		ptep = get_locked_pte(gmap->mm, vmaddr, &ptl);
-		if (likely(ptep))
+		if (likely(ptep)) {
 			ptep_zap_unused(gmap->mm, vmaddr, ptep, 0);
-		pte_unmap_unlock(ptep, ptl);
+			pte_unmap_unlock(ptep, ptl);
+		}
 	}
 }
 EXPORT_SYMBOL_GPL(__gmap_zap);
@@ -1176,6 +1183,7 @@
 static inline void gmap_insert_rmap(struct gmap *sg, unsigned long vmaddr,
 				    struct gmap_rmap *rmap)
 {
+	struct gmap_rmap *temp;
 	void __rcu **slot;
 
 	BUG_ON(!gmap_is_shadow(sg));
@@ -1183,6 +1191,12 @@
 	if (slot) {
 		rmap->next = radix_tree_deref_slot_protected(slot,
 							&sg->guest_table_lock);
+		for (temp = rmap->next; temp; temp = temp->next) {
+			if (temp->raddr == rmap->raddr) {
+				kfree(rmap);
+				return;
+			}
+		}
 		radix_tree_replace_slot(&sg->host_to_rmap, slot, rmap);
 	} else {
 		rmap->next = NULL;
@@ -1661,6 +1675,7 @@
 		return ERR_PTR(-ENOMEM);
 	new->mm = parent->mm;
 	new->parent = gmap_get(parent);
+	new->private = parent->private;
 	new->orig_asce = asce;
 	new->edat_level = edat_level;
 	new->initialized = false;
@@ -2594,6 +2609,18 @@
 	return 0;
 }
 
+/*
+ * Give a chance to schedule after setting a key to 256 pages.
+ * We only hold the mm lock, which is a rwsem and the kvm srcu.
+ * Both can sleep.
+ */
+static int __s390_enable_skey_pmd(pmd_t *pmd, unsigned long addr,
+				  unsigned long next, struct mm_walk *walk)
+{
+	cond_resched();
+	return 0;
+}
+
 static int __s390_enable_skey_hugetlb(pte_t *pte, unsigned long addr,
 				      unsigned long hmask, unsigned long next,
 				      struct mm_walk *walk)
@@ -2613,15 +2640,17 @@
 		return 0;
 
 	start = pmd_val(*pmd) & HPAGE_MASK;
-	end = start + HPAGE_SIZE - 1;
+	end = start + HPAGE_SIZE;
 	__storage_key_init_range(start, end);
 	set_bit(PG_arch_1, &page->flags);
+	cond_resched();
 	return 0;
 }
 
 static const struct mm_walk_ops enable_skey_walk_ops = {
 	.hugetlb_entry		= __s390_enable_skey_hugetlb,
 	.pte_entry		= __s390_enable_skey_pte,
+	.pmd_entry		= __s390_enable_skey_pmd,
 };
 
 int s390_enable_skey(void)
@@ -2705,3 +2734,90 @@
 	mmput(mm);
 }
 EXPORT_SYMBOL_GPL(s390_reset_acc);
+
+/**
+ * s390_unlist_old_asce - Remove the topmost level of page tables from the
+ * list of page tables of the gmap.
+ * @gmap: the gmap whose table is to be removed
+ *
+ * On s390x, KVM keeps a list of all pages containing the page tables of the
+ * gmap (the CRST list). This list is used at tear down time to free all
+ * pages that are now not needed anymore.
+ *
+ * This function removes the topmost page of the tree (the one pointed to by
+ * the ASCE) from the CRST list.
+ *
+ * This means that it will not be freed when the VM is torn down, and needs
+ * to be handled separately by the caller, unless a leak is actually
+ * intended. Notice that this function will only remove the page from the
+ * list, the page will still be used as a top level page table (and ASCE).
+ */
+void s390_unlist_old_asce(struct gmap *gmap)
+{
+	struct page *old;
+
+	old = virt_to_page(gmap->table);
+	spin_lock(&gmap->guest_table_lock);
+	list_del(&old->lru);
+	/*
+	 * Sometimes the topmost page might need to be "removed" multiple
+	 * times, for example if the VM is rebooted into secure mode several
+	 * times concurrently, or if s390_replace_asce fails after calling
+	 * s390_remove_old_asce and is attempted again later. In that case
+	 * the old asce has been removed from the list, and therefore it
+	 * will not be freed when the VM terminates, but the ASCE is still
+	 * in use and still pointed to.
+	 * A subsequent call to replace_asce will follow the pointer and try
+	 * to remove the same page from the list again.
+	 * Therefore it's necessary that the page of the ASCE has valid
+	 * pointers, so list_del can work (and do nothing) without
+	 * dereferencing stale or invalid pointers.
+	 */
+	INIT_LIST_HEAD(&old->lru);
+	spin_unlock(&gmap->guest_table_lock);
+}
+EXPORT_SYMBOL_GPL(s390_unlist_old_asce);
+
+/**
+ * s390_replace_asce - Try to replace the current ASCE of a gmap with a copy
+ * @gmap: the gmap whose ASCE needs to be replaced
+ *
+ * If the allocation of the new top level page table fails, the ASCE is not
+ * replaced.
+ * In any case, the old ASCE is always removed from the gmap CRST list.
+ * Therefore the caller has to make sure to save a pointer to it
+ * beforehand, unless a leak is actually intended.
+ */
+int s390_replace_asce(struct gmap *gmap)
+{
+	unsigned long asce;
+	struct page *page;
+	void *table;
+
+	s390_unlist_old_asce(gmap);
+
+	page = alloc_pages(GFP_KERNEL_ACCOUNT, CRST_ALLOC_ORDER);
+	if (!page)
+		return -ENOMEM;
+	page->index = 0;
+	table = page_to_virt(page);
+	memcpy(table, gmap->table, 1UL << (CRST_ALLOC_ORDER + PAGE_SHIFT));
+
+	/*
+	 * The caller has to deal with the old ASCE, but here we make sure
+	 * the new one is properly added to the CRST list, so that
+	 * it will be freed when the VM is torn down.
+	 */
+	spin_lock(&gmap->guest_table_lock);
+	list_add(&page->lru, &gmap->crst_list);
+	spin_unlock(&gmap->guest_table_lock);
+
+	/* Set new table origin while preserving existing ASCE control bits */
+	asce = (gmap->asce & ~_ASCE_ORIGIN) | __pa(table);
+	WRITE_ONCE(gmap->asce, asce);
+	WRITE_ONCE(gmap->mm->context.gmap_asce, asce);
+	WRITE_ONCE(gmap->table, table);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(s390_replace_asce);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/hugetlbpage.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/hugetlbpage.c
@@ -146,7 +146,7 @@
 	}
 
 	if (!test_and_set_bit(PG_arch_1, &page->flags))
-		__storage_key_init_range(paddr, paddr + size - 1);
+		__storage_key_init_range(paddr, paddr + size);
 }
 
 void set_huge_pte_at(struct mm_struct *mm, unsigned long addr,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/maccess.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/maccess.c
@@ -123,7 +123,7 @@
 /*
  * Copy memory in real mode (kernel to kernel)
  */
-int memcpy_real(void *dest, void *src, size_t count)
+int memcpy_real(void *dest, unsigned long src, size_t count)
 {
 	unsigned long _dest  = (unsigned long)dest;
 	unsigned long _src   = (unsigned long)src;
@@ -175,7 +175,7 @@
 /*
  * Copy memory from kernel (real) to user (virtual)
  */
-int copy_to_user_real(void __user *dest, void *src, unsigned long count)
+int copy_to_user_real(void __user *dest, unsigned long src, unsigned long count)
 {
 	int offs = 0, size, rc;
 	char *buf;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/page-states.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/page-states.c
@@ -131,7 +131,7 @@
 			continue;
 		if (!pud_folded(*pud)) {
 			page = phys_to_page(pud_val(*pud));
-			for (i = 0; i < 3; i++)
+			for (i = 0; i < 4; i++)
 				set_bit(PG_arch_1, &page[i].flags);
 		}
 		mark_kernel_pmd(pud, addr, next);
@@ -152,7 +152,7 @@
 			continue;
 		if (!p4d_folded(*p4d)) {
 			page = phys_to_page(p4d_val(*p4d));
-			for (i = 0; i < 3; i++)
+			for (i = 0; i < 4; i++)
 				set_bit(PG_arch_1, &page[i].flags);
 		}
 		mark_kernel_pud(p4d, addr, next);
@@ -174,7 +174,7 @@
 			continue;
 		if (!pgd_folded(*pgd)) {
 			page = phys_to_page(pgd_val(*pgd));
-			for (i = 0; i < 3; i++)
+			for (i = 0; i < 4; i++)
 				set_bit(PG_arch_1, &page[i].flags);
 		}
 		mark_kernel_p4d(pgd, addr, next);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/pgalloc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/pgalloc.c
@@ -244,13 +244,15 @@
 		/* Free 2K page table fragment of a 4K page */
 		bit = ((unsigned long) table & ~PAGE_MASK)/(PTRS_PER_PTE*sizeof(pte_t));
 		spin_lock_bh(&mm->context.lock);
-		mask = atomic_xor_bits(&page->_refcount, 1U << (bit + 24));
+		mask = atomic_xor_bits(&page->_refcount, 0x11U << (bit + 24));
 		mask >>= 24;
 		if (mask & 3)
 			list_add(&page->lru, &mm->context.pgtable_list);
 		else
 			list_del(&page->lru);
 		spin_unlock_bh(&mm->context.lock);
+		mask = atomic_xor_bits(&page->_refcount, 0x10U << (bit + 24));
+		mask >>= 24;
 		if (mask != 0)
 			return;
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/pgtable.c
@@ -429,22 +429,36 @@
 }
 
 #ifdef CONFIG_PGSTE
-static pmd_t *pmd_alloc_map(struct mm_struct *mm, unsigned long addr)
+static int pmd_lookup(struct mm_struct *mm, unsigned long addr, pmd_t **pmdp)
 {
+	struct vm_area_struct *vma;
 	pgd_t *pgd;
 	p4d_t *p4d;
 	pud_t *pud;
-	pmd_t *pmd;
+
+	/* We need a valid VMA, otherwise this is clearly a fault. */
+	vma = vma_lookup(mm, addr);
+	if (!vma)
+		return -EFAULT;
 
 	pgd = pgd_offset(mm, addr);
-	p4d = p4d_alloc(mm, pgd, addr);
-	if (!p4d)
-		return NULL;
-	pud = pud_alloc(mm, p4d, addr);
-	if (!pud)
-		return NULL;
-	pmd = pmd_alloc(mm, pud, addr);
-	return pmd;
+	if (!pgd_present(*pgd))
+		return -ENOENT;
+
+	p4d = p4d_offset(pgd, addr);
+	if (!p4d_present(*p4d))
+		return -ENOENT;
+
+	pud = pud_offset(p4d, addr);
+	if (!pud_present(*pud))
+		return -ENOENT;
+
+	/* Large PUDs are not supported yet. */
+	if (pud_large(*pud))
+		return -EFAULT;
+
+	*pmdp = pmd_offset(pud, addr);
+	return 0;
 }
 #endif
 
@@ -717,7 +731,7 @@
 		pte_clear(mm, addr, ptep);
 	}
 	if (reset)
-		pgste_val(pgste) &= ~_PGSTE_GPS_USAGE_MASK;
+		pgste_val(pgste) &= ~(_PGSTE_GPS_USAGE_MASK | _PGSTE_GPS_NODAT);
 	pgste_set_unlock(ptep, pgste);
 	preempt_enable();
 }
@@ -734,7 +748,7 @@
 	pgste_val(pgste) |= PGSTE_GR_BIT | PGSTE_GC_BIT;
 	ptev = pte_val(*ptep);
 	if (!(ptev & _PAGE_INVALID) && (ptev & _PAGE_WRITE))
-		page_set_storage_key(ptev & PAGE_MASK, PAGE_DEFAULT_KEY, 1);
+		page_set_storage_key(ptev & PAGE_MASK, PAGE_DEFAULT_KEY, 0);
 	pgste_set_unlock(ptep, pgste);
 	preempt_enable();
 }
@@ -778,8 +792,7 @@
 	pmd_t *pmdp;
 	pte_t *ptep;
 
-	pmdp = pmd_alloc_map(mm, addr);
-	if (unlikely(!pmdp))
+	if (pmd_lookup(mm, addr, &pmdp))
 		return -EFAULT;
 
 	ptl = pmd_lock(mm, pmdp);
@@ -881,8 +894,7 @@
 	pte_t *ptep;
 	int cc = 0;
 
-	pmdp = pmd_alloc_map(mm, addr);
-	if (unlikely(!pmdp))
+	if (pmd_lookup(mm, addr, &pmdp))
 		return -EFAULT;
 
 	ptl = pmd_lock(mm, pmdp);
@@ -935,15 +947,24 @@
 	pmd_t *pmdp;
 	pte_t *ptep;
 
-	pmdp = pmd_alloc_map(mm, addr);
-	if (unlikely(!pmdp))
+	/*
+	 * If we don't have a PTE table and if there is no huge page mapped,
+	 * the storage key is 0.
+	 */
+	*key = 0;
+
+	switch (pmd_lookup(mm, addr, &pmdp)) {
+	case -ENOENT:
+		return 0;
+	case 0:
+		break;
+	default:
 		return -EFAULT;
+	}
 
 	ptl = pmd_lock(mm, pmdp);
 	if (!pmd_present(*pmdp)) {
-		/* Not yet mapped memory has a zero key */
 		spin_unlock(ptl);
-		*key = 0;
 		return 0;
 	}
 
@@ -988,6 +1009,7 @@
 int pgste_perform_essa(struct mm_struct *mm, unsigned long hva, int orc,
 			unsigned long *oldpte, unsigned long *oldpgste)
 {
+	struct vm_area_struct *vma;
 	unsigned long pgstev;
 	spinlock_t *ptl;
 	pgste_t pgste;
@@ -997,6 +1019,10 @@
 	WARN_ON_ONCE(orc > ESSA_MAX);
 	if (unlikely(orc > ESSA_MAX))
 		return -EINVAL;
+
+	vma = vma_lookup(mm, hva);
+	if (!vma || is_vm_hugetlb_page(vma))
+		return -EFAULT;
 	ptep = get_locked_pte(mm, hva, &ptl);
 	if (unlikely(!ptep))
 		return -EFAULT;
@@ -1089,10 +1115,14 @@
 int set_pgste_bits(struct mm_struct *mm, unsigned long hva,
 			unsigned long bits, unsigned long value)
 {
+	struct vm_area_struct *vma;
 	spinlock_t *ptl;
 	pgste_t new;
 	pte_t *ptep;
 
+	vma = vma_lookup(mm, hva);
+	if (!vma || is_vm_hugetlb_page(vma))
+		return -EFAULT;
 	ptep = get_locked_pte(mm, hva, &ptl);
 	if (unlikely(!ptep))
 		return -EFAULT;
@@ -1117,9 +1147,13 @@
  */
 int get_pgste(struct mm_struct *mm, unsigned long hva, unsigned long *pgstep)
 {
+	struct vm_area_struct *vma;
 	spinlock_t *ptl;
 	pte_t *ptep;
 
+	vma = vma_lookup(mm, hva);
+	if (!vma || is_vm_hugetlb_page(vma))
+		return -EFAULT;
 	ptep = get_locked_pte(mm, hva, &ptl);
 	if (unlikely(!ptep))
 		return -EFAULT;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/mm/vmem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/mm/vmem.c
@@ -297,7 +297,7 @@
 	if (end > VMALLOC_START)
 		return;
 #ifdef CONFIG_KASAN
-	if (start < KASAN_SHADOW_END && KASAN_SHADOW_START > end)
+	if (start < KASAN_SHADOW_END && end > KASAN_SHADOW_START)
 		return;
 #endif
 	pmd = pmd_offset(pud, start);
@@ -372,7 +372,7 @@
 	if (end > VMALLOC_START)
 		return;
 #ifdef CONFIG_KASAN
-	if (start < KASAN_SHADOW_END && KASAN_SHADOW_START > end)
+	if (start < KASAN_SHADOW_END && end > KASAN_SHADOW_START)
 		return;
 #endif
 
@@ -426,7 +426,7 @@
 	if (end > VMALLOC_START)
 		return;
 #ifdef CONFIG_KASAN
-	if (start < KASAN_SHADOW_END && KASAN_SHADOW_START > end)
+	if (start < KASAN_SHADOW_END && end > KASAN_SHADOW_START)
 		return;
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/net/bpf_jit_comp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/net/bpf_jit_comp.c
@@ -1229,8 +1229,12 @@
 	EMIT6_DISP_LH(0xeb000000, is32 ? (op32) : (op64),		\
 		      (insn->imm & BPF_FETCH) ? src_reg : REG_W0,	\
 		      src_reg, dst_reg, off);				\
-	if (is32 && (insn->imm & BPF_FETCH))				\
-		EMIT_ZERO(src_reg);					\
+	if (insn->imm & BPF_FETCH) {					\
+		/* bcr 14,0 - see atomic_fetch_{add,and,or,xor}() */	\
+		_EMIT2(0x07e0);						\
+		if (is32)                                               \
+			EMIT_ZERO(src_reg);				\
+	}								\
 } while (0)
 		case BPF_ADD:
 		case BPF_ADD | BPF_FETCH:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/Makefile
@@ -5,5 +5,5 @@
 
 obj-$(CONFIG_PCI)	+= pci.o pci_irq.o pci_dma.o pci_clp.o pci_sysfs.o \
 			   pci_event.o pci_debug.o pci_insn.o pci_mmio.o \
-			   pci_bus.o
+			   pci_bus.o pci_kvm_hook.o
 obj-$(CONFIG_PCI_IOV)	+= pci_iov.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci.c
@@ -61,6 +61,12 @@
 
 static struct kmem_cache *zdev_fmb_cache;
 
+/* AEN structures that must be preserved over KVM module re-insertion */
+union zpci_sic_iib *zpci_aipb;
+EXPORT_SYMBOL_GPL(zpci_aipb);
+struct airq_iv *zpci_aif_sbv;
+EXPORT_SYMBOL_GPL(zpci_aif_sbv);
+
 struct zpci_dev *get_zdev_by_fid(u32 fid)
 {
 	struct zpci_dev *tmp, *zdev = NULL;
@@ -69,6 +75,7 @@
 	list_for_each_entry(tmp, &zpci_list, entry) {
 		if (tmp->fid == fid) {
 			zdev = tmp;
+			zpci_zdev_get(zdev);
 			break;
 		}
 	}
@@ -119,11 +126,13 @@
 	fib.pba = base;
 	fib.pal = limit;
 	fib.iota = iota | ZPCI_IOTA_RTTO_FLAG;
+	fib.gd = zdev->gisa;
 	cc = zpci_mod_fc(req, &fib, &status);
 	if (cc)
 		zpci_dbg(3, "reg ioat fid:%x, cc:%d, status:%d\n", zdev->fid, cc, status);
 	return cc;
 }
+EXPORT_SYMBOL_GPL(zpci_register_ioat);
 
 /* Modify PCI: Unregister I/O address translation parameters */
 int zpci_unregister_ioat(struct zpci_dev *zdev, u8 dmaas)
@@ -132,6 +141,8 @@
 	struct zpci_fib fib = {0};
 	u8 cc, status;
 
+	fib.gd = zdev->gisa;
+
 	cc = zpci_mod_fc(req, &fib, &status);
 	if (cc)
 		zpci_dbg(3, "unreg ioat fid:%x, cc:%d, status:%d\n", zdev->fid, cc, status);
@@ -159,6 +170,7 @@
 	atomic64_set(&zdev->unmapped_pages, 0);
 
 	fib.fmb_addr = virt_to_phys(zdev->fmb);
+	fib.gd = zdev->gisa;
 	cc = zpci_mod_fc(req, &fib, &status);
 	if (cc) {
 		kmem_cache_free(zdev_fmb_cache, zdev->fmb);
@@ -177,6 +189,8 @@
 	if (!zdev->fmb)
 		return -EINVAL;
 
+	fib.gd = zdev->gisa;
+
 	/* Function measurement is disabled if fmb address is zero */
 	cc = zpci_mod_fc(req, &fib, &status);
 	if (cc == 3) /* Function already gone. */
@@ -227,7 +241,7 @@
 /* combine single writes by using store-block insn */
 void __iowrite64_copy(void __iomem *to, const void *from, size_t count)
 {
-       zpci_memcpy_toio(to, from, count);
+	zpci_memcpy_toio(to, from, count * 8);
 }
 
 static void __iomem *__ioremap(phys_addr_t addr, size_t size, pgprot_t prot)
@@ -481,6 +495,34 @@
 	spin_unlock(&zpci_iomap_lock);
 }
 
+static void zpci_do_update_iomap_fh(struct zpci_dev *zdev, u32 fh)
+{
+	int bar, idx;
+
+	spin_lock(&zpci_iomap_lock);
+	for (bar = 0; bar < PCI_STD_NUM_BARS; bar++) {
+		if (!zdev->bars[bar].size)
+			continue;
+		idx = zdev->bars[bar].map_idx;
+		if (!zpci_iomap_start[idx].count)
+			continue;
+		WRITE_ONCE(zpci_iomap_start[idx].fh, zdev->fh);
+	}
+	spin_unlock(&zpci_iomap_lock);
+}
+
+void zpci_update_fh(struct zpci_dev *zdev, u32 fh)
+{
+	if (!fh || zdev->fh == fh)
+		return;
+
+	zdev->fh = fh;
+	if (zpci_use_mio(zdev))
+		return;
+	if (zdev->has_resources && zdev_enabled(zdev))
+		zpci_do_update_iomap_fh(zdev, fh);
+}
+
 static struct resource *__alloc_res(struct zpci_dev *zdev, unsigned long start,
 				    unsigned long size, unsigned long flags)
 {
@@ -502,8 +544,7 @@
 	return r;
 }
 
-int zpci_setup_bus_resources(struct zpci_dev *zdev,
-			     struct list_head *resources)
+int zpci_setup_bus_resources(struct zpci_dev *zdev)
 {
 	unsigned long addr, size, flags;
 	struct resource *res;
@@ -539,7 +580,6 @@
 			return -ENOMEM;
 		}
 		zdev->bars[i].res = res;
-		pci_add_resource(resources, res);
 	}
 	zdev->has_resources = 1;
 
@@ -548,17 +588,23 @@
 
 static void zpci_cleanup_bus_resources(struct zpci_dev *zdev)
 {
+	struct resource *res;
 	int i;
 
+	pci_lock_rescan_remove();
 	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
-		if (!zdev->bars[i].size || !zdev->bars[i].res)
+		res = zdev->bars[i].res;
+		if (!res)
 			continue;
 
+		release_resource(res);
+		pci_bus_remove_resource(zdev->zbus->bus, res);
 		zpci_free_iomap(zdev, zdev->bars[i].map_idx);
-		release_resource(zdev->bars[i].res);
-		kfree(zdev->bars[i].res);
+		zdev->bars[i].res = NULL;
+		kfree(res);
 	}
 	zdev->has_resources = 0;
+	pci_unlock_rescan_remove();
 }
 
 int pcibios_add_device(struct pci_dev *pdev)
@@ -668,9 +714,10 @@
 	if (clp_enable_fh(zdev, &fh, ZPCI_NR_DMA_SPACES))
 		rc = -EIO;
 	else
-		zdev->fh = fh;
+		zpci_update_fh(zdev, fh);
 	return rc;
 }
+EXPORT_SYMBOL_GPL(zpci_enable_device);
 
 int zpci_disable_device(struct zpci_dev *zdev)
 {
@@ -679,14 +726,14 @@
 
 	cc = clp_disable_fh(zdev, &fh);
 	if (!cc) {
-		zdev->fh = fh;
+		zpci_update_fh(zdev, fh);
 	} else if (cc == CLP_RC_SETPCIFN_ALRDY) {
 		pr_info("Disabling PCI function %08x had no effect as it was already disabled\n",
 			zdev->fid);
 		/* Function is already disabled - update handle */
 		rc = clp_refresh_fh(zdev->fid, &fh);
 		if (!rc) {
-			zdev->fh = fh;
+			zpci_update_fh(zdev, fh);
 			rc = -EINVAL;
 		}
 	} else {
@@ -694,6 +741,66 @@
 	}
 	return rc;
 }
+EXPORT_SYMBOL_GPL(zpci_disable_device);
+
+/**
+ * zpci_hot_reset_device - perform a reset of the given zPCI function
+ * @zdev: the slot which should be reset
+ *
+ * Performs a low level reset of the zPCI function. The reset is low level in
+ * the sense that the zPCI function can be reset without detaching it from the
+ * common PCI subsystem. The reset may be performed while under control of
+ * either DMA or IOMMU APIs in which case the existing DMA/IOMMU translation
+ * table is reinstated at the end of the reset.
+ *
+ * After the reset the functions internal state is reset to an initial state
+ * equivalent to its state during boot when first probing a driver.
+ * Consequently after reset the PCI function requires re-initialization via the
+ * common PCI code including re-enabling IRQs via pci_alloc_irq_vectors()
+ * and enabling the function via e.g.pci_enablde_device_flags().The caller
+ * must guard against concurrent reset attempts.
+ *
+ * In most cases this function should not be called directly but through
+ * pci_reset_function() or pci_reset_bus() which handle the save/restore and
+ * locking.
+ *
+ * Return: 0 on success and an error value otherwise
+ */
+int zpci_hot_reset_device(struct zpci_dev *zdev)
+{
+	int rc;
+
+	zpci_dbg(3, "rst fid:%x, fh:%x\n", zdev->fid, zdev->fh);
+	if (zdev_enabled(zdev)) {
+		/* Disables device access, DMAs and IRQs (reset state) */
+		rc = zpci_disable_device(zdev);
+		/*
+		 * Due to a z/VM vs LPAR inconsistency in the error state the
+		 * FH may indicate an enabled device but disable says the
+		 * device is already disabled don't treat it as an error here.
+		 */
+		if (rc == -EINVAL)
+			rc = 0;
+		if (rc)
+			return rc;
+	}
+
+	rc = zpci_enable_device(zdev);
+	if (rc)
+		return rc;
+
+	if (zdev->dma_table)
+		rc = zpci_register_ioat(zdev, 0, zdev->start_dma, zdev->end_dma,
+					(u64)zdev->dma_table);
+	else
+		rc = zpci_dma_init_device(zdev);
+	if (rc) {
+		zpci_disable_device(zdev);
+		return rc;
+	}
+
+	return 0;
+}
 
 /**
  * zpci_create_device() - Create a new zpci_dev and add it to the zbus
@@ -728,6 +835,7 @@
 
 	kref_init(&zdev->kref);
 	mutex_init(&zdev->lock);
+	mutex_init(&zdev->kzdev_lock);
 
 	rc = zpci_init_iommu(zdev);
 	if (rc)
@@ -776,7 +884,7 @@
 {
 	int rc;
 
-	zdev->fh = fh;
+	zpci_update_fh(zdev, fh);
 	/* the PCI function will be scanned once function 0 appears */
 	if (!zdev->zbus->bus)
 		return 0;
@@ -903,6 +1011,59 @@
 }
 EXPORT_SYMBOL(zpci_report_error);
 
+/**
+ * zpci_clear_error_state() - Clears the zPCI error state of the device
+ * @zdev: The zdev for which the zPCI error state should be reset
+ *
+ * Clear the zPCI error state of the device. If clearing the zPCI error state
+ * fails the device is left in the error state. In this case it may make sense
+ * to call zpci_io_perm_failure() on the associated pdev if it exists.
+ *
+ * Returns: 0 on success, -EIO otherwise
+ */
+int zpci_clear_error_state(struct zpci_dev *zdev)
+{
+	u64 req = ZPCI_CREATE_REQ(zdev->fh, 0, ZPCI_MOD_FC_RESET_ERROR);
+	struct zpci_fib fib = {0};
+	u8 status;
+	int cc;
+
+	cc = zpci_mod_fc(req, &fib, &status);
+	if (cc) {
+		zpci_dbg(3, "ces fid:%x, cc:%d, status:%x\n", zdev->fid, cc, status);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+/**
+ * zpci_reset_load_store_blocked() - Re-enables L/S from error state
+ * @zdev: The zdev for which to unblock load/store access
+ *
+ * Re-enables load/store access for a PCI function in the error state while
+ * keeping DMA blocked. In this state drivers can poke MMIO space to determine
+ * if error recovery is possible while catching any rogue DMA access from the
+ * device.
+ *
+ * Returns: 0 on success, -EIO otherwise
+ */
+int zpci_reset_load_store_blocked(struct zpci_dev *zdev)
+{
+	u64 req = ZPCI_CREATE_REQ(zdev->fh, 0, ZPCI_MOD_FC_RESET_BLOCK);
+	struct zpci_fib fib = {0};
+	u8 status;
+	int cc;
+
+	cc = zpci_mod_fc(req, &fib, &status);
+	if (cc) {
+		zpci_dbg(3, "rls fid:%x, cc:%d, status:%x\n", zdev->fid, cc, status);
+		return -EIO;
+	}
+
+	return 0;
+}
+
 static int zpci_mem_init(void)
 {
 	BUILD_BUG_ON(!is_power_of_2(__alignof__(struct zpci_fmb)) ||
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_bus.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_bus.c
@@ -41,9 +41,7 @@
  */
 static int zpci_bus_prepare_device(struct zpci_dev *zdev)
 {
-	struct resource_entry *window, *n;
-	struct resource *res;
-	int rc;
+	int rc, i;
 
 	if (!zdev_enabled(zdev)) {
 		rc = zpci_enable_device(zdev);
@@ -57,10 +55,10 @@
 	}
 
 	if (!zdev->has_resources) {
-		zpci_setup_bus_resources(zdev, &zdev->zbus->resources);
-		resource_list_for_each_entry_safe(window, n, &zdev->zbus->resources) {
-			res = window->res;
-			pci_bus_add_resource(zdev->zbus->bus, res, 0);
+		zpci_setup_bus_resources(zdev);
+		for (i = 0; i < PCI_STD_NUM_BARS; i++) {
+			if (zdev->bars[i].res)
+				pci_bus_add_resource(zdev->zbus->bus, zdev->bars[i].res, 0);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_bus.h
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_bus.h
@@ -19,7 +19,8 @@
 void zpci_release_device(struct kref *kref);
 static inline void zpci_zdev_put(struct zpci_dev *zdev)
 {
-	kref_put(&zdev->kref, zpci_release_device);
+	if (zdev)
+		kref_put(&zdev->kref, zpci_release_device);
 }
 
 static inline void zpci_zdev_get(struct zpci_dev *zdev)
@@ -29,8 +30,7 @@
 
 int zpci_alloc_domain(int domain);
 void zpci_free_domain(int domain);
-int zpci_setup_bus_resources(struct zpci_dev *zdev,
-			     struct list_head *resources);
+int zpci_setup_bus_resources(struct zpci_dev *zdev);
 
 static inline struct zpci_dev *get_zdev_by_bus(struct pci_bus *bus,
 					       unsigned int devfn)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_clp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_clp.c
@@ -22,6 +22,8 @@
 #include <asm/clp.h>
 #include <uapi/asm/clp.h>
 
+#include "pci_bus.h"
+
 bool zpci_unique_uid;
 
 void update_uid_checking(bool new)
@@ -103,6 +105,8 @@
 	zdev->max_msi = response->noi;
 	zdev->fmb_update = response->mui;
 	zdev->version = response->version;
+	zdev->maxstbl = response->maxstbl;
+	zdev->dtsm = response->dtsm;
 
 	switch (response->version) {
 	case 1:
@@ -226,12 +230,16 @@
 {
 	struct clp_req_rsp_set_pci *rrb;
 	int rc, retries = 100;
+	u32 gisa = 0;
 
 	*fh = 0;
 	rrb = clp_alloc_block(GFP_KERNEL);
 	if (!rrb)
 		return -ENOMEM;
 
+	if (command != CLP_SET_DISABLE_PCI_FN)
+		gisa = zdev->gisa;
+
 	do {
 		memset(rrb, 0, sizeof(*rrb));
 		rrb->request.hdr.len = sizeof(rrb->request);
@@ -240,6 +248,7 @@
 		rrb->request.fh = zdev->fh;
 		rrb->request.oc = command;
 		rrb->request.ndas = nr_dma_as;
+		rrb->request.gisa = gisa;
 
 		rc = clp_req(rrb, CLP_LPS_PCI);
 		if (rrb->response.hdr.rsp == CLP_RC_SETPCIFN_BUSY) {
@@ -403,8 +412,11 @@
 		return;
 
 	zdev = get_zdev_by_fid(entry->fid);
-	if (!zdev)
-		zpci_create_device(entry->fid, entry->fh, entry->config_state);
+	if (zdev) {
+		zpci_zdev_put(zdev);
+		return;
+	}
+	zpci_create_device(entry->fid, entry->fh, entry->config_state);
 }
 
 int clp_scan_pci_devices(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_dma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_dma.c
@@ -542,6 +542,17 @@
 		s->dma_length = 0;
 	}
 }
+
+static unsigned long *bitmap_vzalloc(size_t bits, gfp_t flags)
+{
+	size_t n = BITS_TO_LONGS(bits);
+	size_t bytes;
+
+	if (unlikely(check_mul_overflow(n, sizeof(unsigned long), &bytes)))
+		return NULL;
+
+	return vzalloc(bytes);
+}
 	
 int zpci_dma_init_device(struct zpci_dev *zdev)
 {
@@ -578,13 +589,13 @@
 				zdev->end_dma - zdev->start_dma + 1);
 	zdev->end_dma = zdev->start_dma + zdev->iommu_size - 1;
 	zdev->iommu_pages = zdev->iommu_size >> PAGE_SHIFT;
-	zdev->iommu_bitmap = vzalloc(zdev->iommu_pages / 8);
+	zdev->iommu_bitmap = bitmap_vzalloc(zdev->iommu_pages, GFP_KERNEL);
 	if (!zdev->iommu_bitmap) {
 		rc = -ENOMEM;
 		goto free_dma_table;
 	}
 	if (!s390_iommu_strict) {
-		zdev->lazy_bitmap = vzalloc(zdev->iommu_pages / 8);
+		zdev->lazy_bitmap = bitmap_vzalloc(zdev->iommu_pages, GFP_KERNEL);
 		if (!zdev->lazy_bitmap) {
 			rc = -ENOMEM;
 			goto free_bitmap;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_event.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_event.c
@@ -47,25 +47,247 @@
 	u16 pec;			/* PCI event code */
 } __packed;
 
+static inline bool ers_result_indicates_abort(pci_ers_result_t ers_res)
+{
+	switch (ers_res) {
+	case PCI_ERS_RESULT_CAN_RECOVER:
+	case PCI_ERS_RESULT_RECOVERED:
+	case PCI_ERS_RESULT_NEED_RESET:
+		return false;
+	default:
+		return true;
+	}
+}
+
+static bool is_passed_through(struct zpci_dev *zdev)
+{
+	return zdev->s390_domain;
+}
+
+static bool is_driver_supported(struct pci_driver *driver)
+{
+	if (!driver || !driver->err_handler)
+		return false;
+	if (!driver->err_handler->error_detected)
+		return false;
+	if (!driver->err_handler->slot_reset)
+		return false;
+	if (!driver->err_handler->resume)
+		return false;
+	return true;
+}
+
+static pci_ers_result_t zpci_event_notify_error_detected(struct pci_dev *pdev,
+							 struct pci_driver *driver)
+{
+	pci_ers_result_t ers_res = PCI_ERS_RESULT_DISCONNECT;
+
+	ers_res = driver->err_handler->error_detected(pdev,  pdev->error_state);
+	if (ers_result_indicates_abort(ers_res))
+		pr_info("%s: Automatic recovery failed after initial reporting\n", pci_name(pdev));
+	else if (ers_res == PCI_ERS_RESULT_NEED_RESET)
+		pr_debug("%s: Driver needs reset to recover\n", pci_name(pdev));
+
+	return ers_res;
+}
+
+static pci_ers_result_t zpci_event_do_error_state_clear(struct pci_dev *pdev,
+							struct pci_driver *driver)
+{
+	pci_ers_result_t ers_res = PCI_ERS_RESULT_DISCONNECT;
+	struct zpci_dev *zdev = to_zpci(pdev);
+	int rc;
+
+	pr_info("%s: Unblocking device access for examination\n", pci_name(pdev));
+	rc = zpci_reset_load_store_blocked(zdev);
+	if (rc) {
+		pr_err("%s: Unblocking device access failed\n", pci_name(pdev));
+		/* Let's try a full reset instead */
+		return PCI_ERS_RESULT_NEED_RESET;
+	}
+
+	if (driver->err_handler->mmio_enabled) {
+		ers_res = driver->err_handler->mmio_enabled(pdev);
+		if (ers_result_indicates_abort(ers_res)) {
+			pr_info("%s: Automatic recovery failed after MMIO re-enable\n",
+				pci_name(pdev));
+			return ers_res;
+		} else if (ers_res == PCI_ERS_RESULT_NEED_RESET) {
+			pr_debug("%s: Driver needs reset to recover\n", pci_name(pdev));
+			return ers_res;
+		}
+	}
+
+	pr_debug("%s: Unblocking DMA\n", pci_name(pdev));
+	rc = zpci_clear_error_state(zdev);
+	if (!rc) {
+		pdev->error_state = pci_channel_io_normal;
+	} else {
+		pr_err("%s: Unblocking DMA failed\n", pci_name(pdev));
+		/* Let's try a full reset instead */
+		return PCI_ERS_RESULT_NEED_RESET;
+	}
+
+	return ers_res;
+}
+
+static pci_ers_result_t zpci_event_do_reset(struct pci_dev *pdev,
+					    struct pci_driver *driver)
+{
+	pci_ers_result_t ers_res = PCI_ERS_RESULT_DISCONNECT;
+
+	pr_info("%s: Initiating reset\n", pci_name(pdev));
+	if (zpci_hot_reset_device(to_zpci(pdev))) {
+		pr_err("%s: The reset request failed\n", pci_name(pdev));
+		return ers_res;
+	}
+	pdev->error_state = pci_channel_io_normal;
+	ers_res = driver->err_handler->slot_reset(pdev);
+	if (ers_result_indicates_abort(ers_res)) {
+		pr_info("%s: Automatic recovery failed after slot reset\n", pci_name(pdev));
+		return ers_res;
+	}
+
+	return ers_res;
+}
+
+/* zpci_event_attempt_error_recovery - Try to recover the given PCI function
+ * @pdev: PCI function to recover currently in the error state
+ *
+ * We follow the scheme outlined in Documentation/PCI/pci-error-recovery.rst.
+ * With the simplification that recovery always happens per function
+ * and the platform determines which functions are affected for
+ * multi-function devices.
+ */
+static pci_ers_result_t zpci_event_attempt_error_recovery(struct pci_dev *pdev)
+{
+	pci_ers_result_t ers_res = PCI_ERS_RESULT_DISCONNECT;
+	struct pci_driver *driver;
+
+	/*
+	 * Ensure that the PCI function is not removed concurrently, no driver
+	 * is unbound or probed and that userspace can't access its
+	 * configuration space while we perform recovery.
+	 */
+	pci_dev_lock(pdev);
+	if (pdev->error_state == pci_channel_io_perm_failure) {
+		ers_res = PCI_ERS_RESULT_DISCONNECT;
+		goto out_unlock;
+	}
+	pdev->error_state = pci_channel_io_frozen;
+
+	if (is_passed_through(to_zpci(pdev))) {
+		pr_info("%s: Cannot be recovered in the host because it is a pass-through device\n",
+			pci_name(pdev));
+		goto out_unlock;
+	}
+
+	driver = to_pci_driver(pdev->dev.driver);
+	if (!is_driver_supported(driver)) {
+		if (!driver)
+			pr_info("%s: Cannot be recovered because no driver is bound to the device\n",
+				pci_name(pdev));
+		else
+			pr_info("%s: The %s driver bound to the device does not support error recovery\n",
+				pci_name(pdev),
+				driver->name);
+		goto out_unlock;
+	}
+
+	ers_res = zpci_event_notify_error_detected(pdev, driver);
+	if (ers_result_indicates_abort(ers_res))
+		goto out_unlock;
+
+	if (ers_res == PCI_ERS_RESULT_CAN_RECOVER) {
+		ers_res = zpci_event_do_error_state_clear(pdev, driver);
+		if (ers_result_indicates_abort(ers_res))
+			goto out_unlock;
+	}
+
+	if (ers_res == PCI_ERS_RESULT_NEED_RESET)
+		ers_res = zpci_event_do_reset(pdev, driver);
+
+	if (ers_res != PCI_ERS_RESULT_RECOVERED) {
+		pr_err("%s: Automatic recovery failed; operator intervention is required\n",
+		       pci_name(pdev));
+		goto out_unlock;
+	}
+
+	pr_info("%s: The device is ready to resume operations\n", pci_name(pdev));
+	if (driver->err_handler->resume)
+		driver->err_handler->resume(pdev);
+out_unlock:
+	pci_dev_unlock(pdev);
+
+	return ers_res;
+}
+
+/* zpci_event_io_failure - Report PCI channel failure state to driver
+ * @pdev: PCI function for which to report
+ * @es: PCI channel failure state to report
+ */
+static void zpci_event_io_failure(struct pci_dev *pdev, pci_channel_state_t es)
+{
+	struct pci_driver *driver;
+
+	pci_dev_lock(pdev);
+	pdev->error_state = es;
+	/**
+	 * While vfio-pci's error_detected callback notifies user-space QEMU
+	 * reacts to this by freezing the guest. In an s390 environment PCI
+	 * errors are rarely fatal so this is overkill. Instead in the future
+	 * we will inject the error event and let the guest recover the device
+	 * itself.
+	 */
+	if (is_passed_through(to_zpci(pdev)))
+		goto out;
+	driver = to_pci_driver(pdev->dev.driver);
+	if (driver && driver->err_handler && driver->err_handler->error_detected)
+		driver->err_handler->error_detected(pdev, pdev->error_state);
+out:
+	pci_dev_unlock(pdev);
+}
+
 static void __zpci_event_error(struct zpci_ccdf_err *ccdf)
 {
 	struct zpci_dev *zdev = get_zdev_by_fid(ccdf->fid);
 	struct pci_dev *pdev = NULL;
+	pci_ers_result_t ers_res;
 
+	zpci_dbg(3, "err fid:%x, fh:%x, pec:%x\n",
+		 ccdf->fid, ccdf->fh, ccdf->pec);
 	zpci_err("error CCDF:\n");
 	zpci_err_hex(ccdf, sizeof(*ccdf));
 
-	if (zdev)
-		pdev = pci_get_slot(zdev->zbus->bus, zdev->devfn);
+	if (zdev) {
+		zpci_update_fh(zdev, ccdf->fh);
+		if (zdev->zbus->bus)
+			pdev = pci_get_slot(zdev->zbus->bus, zdev->devfn);
+	}
 
 	pr_err("%s: Event 0x%x reports an error for PCI function 0x%x\n",
 	       pdev ? pci_name(pdev) : "n/a", ccdf->pec, ccdf->fid);
 
 	if (!pdev)
-		return;
+		goto no_pdev;
 
-	pdev->error_state = pci_channel_io_perm_failure;
+	switch (ccdf->pec) {
+	case 0x003a: /* Service Action or Error Recovery Successful */
+		ers_res = zpci_event_attempt_error_recovery(pdev);
+		if (ers_res != PCI_ERS_RESULT_RECOVERED)
+			zpci_event_io_failure(pdev, pci_channel_io_perm_failure);
+		break;
+	default:
+		/*
+		 * Mark as frozen not permanently failed because the device
+		 * could be subsequently recovered by the platform.
+		 */
+		zpci_event_io_failure(pdev, pci_channel_io_frozen);
+		break;
+	}
 	pci_dev_put(pdev);
+no_pdev:
+	zpci_zdev_put(zdev);
 }
 
 void zpci_event_error(void *data)
@@ -76,7 +298,7 @@
 
 static void zpci_event_hard_deconfigured(struct zpci_dev *zdev, u32 fh)
 {
-	zdev->fh = fh;
+	zpci_update_fh(zdev, fh);
 	/* Give the driver a hint that the function is
 	 * already unusable.
 	 */
@@ -94,8 +316,11 @@
 static void __zpci_event_availability(struct zpci_ccdf_avail *ccdf)
 {
 	struct zpci_dev *zdev = get_zdev_by_fid(ccdf->fid);
+	bool existing_zdev = !!zdev;
 	enum zpci_state state;
 
+	zpci_dbg(3, "avl fid:%x, fh:%x, pec:%x\n",
+		 ccdf->fid, ccdf->fh, ccdf->pec);
 	zpci_err("avail CCDF:\n");
 	zpci_err_hex(ccdf, sizeof(*ccdf));
 
@@ -117,7 +342,7 @@
 		if (!zdev)
 			zpci_create_device(ccdf->fid, ccdf->fh, ZPCI_FN_STATE_STANDBY);
 		else
-			zdev->fh = ccdf->fh;
+			zpci_update_fh(zdev, ccdf->fh);
 		break;
 	case 0x0303: /* Deconfiguration requested */
 		if (zdev) {
@@ -126,7 +351,7 @@
 			 */
 			if (zdev->state != ZPCI_FN_STATE_CONFIGURED)
 				break;
-			zdev->fh = ccdf->fh;
+			zpci_update_fh(zdev, ccdf->fh);
 			zpci_deconfigure_device(zdev);
 		}
 		break;
@@ -156,6 +381,8 @@
 	default:
 		break;
 	}
+	if (existing_zdev)
+		zpci_zdev_put(zdev);
 }
 
 void zpci_event_availability(void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_insn.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_insn.c
@@ -59,6 +59,7 @@
 
 	return cc;
 }
+EXPORT_SYMBOL_GPL(zpci_mod_fc);
 
 /* Refresh PCI Translations */
 static inline u8 __rpcit(u64 fn, u64 addr, u64 range, u8 *status)
@@ -97,7 +98,7 @@
 }
 
 /* Set Interruption Controls */
-int __zpci_set_irq_ctrl(u16 ctl, u8 isc, union zpci_sic_iib *iib)
+int zpci_set_irq_ctrl(u16 ctl, u8 isc, union zpci_sic_iib *iib)
 {
 	if (!test_facility(72))
 		return -EIO;
@@ -108,6 +109,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(zpci_set_irq_ctrl);
 
 /* PCI Load */
 static inline int ____pcilg(u64 *data, u64 req, u64 offset, u8 *status)
@@ -163,7 +165,7 @@
 			       unsigned long len)
 {
 	struct zpci_iomap_entry *entry = &zpci_iomap_start[ZPCI_IDX(addr)];
-	u64 req = ZPCI_CREATE_REQ(entry->fh, entry->bar, len);
+	u64 req = ZPCI_CREATE_REQ(READ_ONCE(entry->fh), entry->bar, len);
 
 	return __zpci_load(data, req, ZPCI_OFFSET(addr));
 }
@@ -244,7 +246,7 @@
 				unsigned long len)
 {
 	struct zpci_iomap_entry *entry = &zpci_iomap_start[ZPCI_IDX(addr)];
-	u64 req = ZPCI_CREATE_REQ(entry->fh, entry->bar, len);
+	u64 req = ZPCI_CREATE_REQ(READ_ONCE(entry->fh), entry->bar, len);
 
 	return __zpci_store(data, req, ZPCI_OFFSET(addr));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_irq.c
@@ -11,16 +11,10 @@
 
 #include <asm/isc.h>
 #include <asm/airq.h>
+#include <asm/tpi.h>
 
 static enum {FLOATING, DIRECTED} irq_delivery;
 
-#define	SIC_IRQ_MODE_ALL		0
-#define	SIC_IRQ_MODE_SINGLE		1
-#define	SIC_IRQ_MODE_DIRECT		4
-#define	SIC_IRQ_MODE_D_ALL		16
-#define	SIC_IRQ_MODE_D_SINGLE		17
-#define	SIC_IRQ_MODE_SET_CPU		18
-
 /*
  * summary bit vector
  * FLOATING - summary bit per function
@@ -45,10 +39,11 @@
 	fib.fmt0.isc = PCI_ISC;
 	fib.fmt0.sum = 1;	/* enable summary notifications */
 	fib.fmt0.noi = airq_iv_end(zdev->aibv);
-	fib.fmt0.aibv = (unsigned long) zdev->aibv->vector;
+	fib.fmt0.aibv = virt_to_phys(zdev->aibv->vector);
 	fib.fmt0.aibvo = 0;	/* each zdev has its own interrupt vector */
-	fib.fmt0.aisb = (unsigned long) zpci_sbv->vector + (zdev->aisb/64)*8;
+	fib.fmt0.aisb = virt_to_phys(zpci_sbv->vector) + (zdev->aisb / 64) * 8;
 	fib.fmt0.aisbo = zdev->aisb & 63;
+	fib.gd = zdev->gisa;
 
 	return zpci_mod_fc(req, &fib, &status) ? -EIO : 0;
 }
@@ -60,6 +55,8 @@
 	struct zpci_fib fib = {0};
 	u8 cc, status;
 
+	fib.gd = zdev->gisa;
+
 	cc = zpci_mod_fc(req, &fib, &status);
 	if (cc == 3 || (cc == 1 && status == 24))
 		/* Function already gone or IRQs already deregistered. */
@@ -78,6 +75,7 @@
 	fib.fmt = 1;
 	fib.fmt1.noi = zdev->msi_nr_irqs;
 	fib.fmt1.dibvo = zdev->msi_first_bit;
+	fib.gd = zdev->gisa;
 
 	return zpci_mod_fc(req, &fib, &status) ? -EIO : 0;
 }
@@ -90,6 +88,7 @@
 	u8 cc, status;
 
 	fib.fmt = 1;
+	fib.gd = zdev->gisa;
 	cc = zpci_mod_fc(req, &fib, &status);
 	if (cc == 3 || (cc == 1 && status == 24))
 		/* Function already gone or IRQs already deregistered. */
@@ -153,6 +152,7 @@
 static void zpci_handle_cpu_local_irq(bool rescan)
 {
 	struct airq_iv *dibv = zpci_ibv[smp_processor_id()];
+	union zpci_sic_iib iib = {{0}};
 	unsigned long bit;
 	int irqs_on = 0;
 
@@ -164,7 +164,7 @@
 				/* End of second scan with interrupts on. */
 				break;
 			/* First scan complete, reenable interrupts. */
-			if (zpci_set_irq_ctrl(SIC_IRQ_MODE_D_SINGLE, PCI_ISC))
+			if (zpci_set_irq_ctrl(SIC_IRQ_MODE_D_SINGLE, PCI_ISC, &iib))
 				break;
 			bit = 0;
 			continue;
@@ -192,6 +192,7 @@
 static void zpci_handle_fallback_irq(void)
 {
 	struct cpu_irq_data *cpu_data;
+	union zpci_sic_iib iib = {{0}};
 	unsigned long cpu;
 	int irqs_on = 0;
 
@@ -202,7 +203,7 @@
 				/* End of second scan with interrupts on. */
 				break;
 			/* First scan complete, reenable interrupts. */
-			if (zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, PCI_ISC))
+			if (zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, PCI_ISC, &iib))
 				break;
 			cpu = 0;
 			continue;
@@ -216,8 +217,11 @@
 	}
 }
 
-static void zpci_directed_irq_handler(struct airq_struct *airq, bool floating)
+static void zpci_directed_irq_handler(struct airq_struct *airq,
+				      struct tpi_info *tpi_info)
 {
+	bool floating = !tpi_info->directed_irq;
+
 	if (floating) {
 		inc_irq_stat(IRQIO_PCF);
 		zpci_handle_fallback_irq();
@@ -227,8 +231,10 @@
 	}
 }
 
-static void zpci_floating_irq_handler(struct airq_struct *airq, bool floating)
+static void zpci_floating_irq_handler(struct airq_struct *airq,
+				      struct tpi_info *tpi_info)
 {
+	union zpci_sic_iib iib = {{0}};
 	unsigned long si, ai;
 	struct airq_iv *aibv;
 	int irqs_on = 0;
@@ -242,7 +248,7 @@
 				/* End of second scan with interrupts on. */
 				break;
 			/* First scan complete, reenable interrupts. */
-			if (zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, PCI_ISC))
+			if (zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, PCI_ISC, &iib))
 				break;
 			si = 0;
 			continue;
@@ -291,7 +297,7 @@
 		zdev->aisb = bit;
 
 		/* Create adapter interrupt vector */
-		zdev->aibv = airq_iv_create(msi_vecs, AIRQ_IV_DATA | AIRQ_IV_BITLOCK);
+		zdev->aibv = airq_iv_create(msi_vecs, AIRQ_IV_DATA | AIRQ_IV_BITLOCK, NULL);
 		if (!zdev->aibv)
 			return -ENOMEM;
 
@@ -387,6 +393,15 @@
 		airq_iv_free(zpci_ibv[0], zdev->msi_first_bit, zdev->msi_nr_irqs);
 }
 
+void arch_restore_msi_irqs(struct pci_dev *pdev)
+{
+	struct zpci_dev *zdev = to_zpci(pdev);
+
+	if (!zdev->irqs_registered)
+		zpci_set_irq(zdev);
+	default_restore_msi_irqs(pdev);
+}
+
 static struct airq_struct zpci_airq = {
 	.handler = zpci_floating_irq_handler,
 	.isc = PCI_ISC,
@@ -395,11 +410,12 @@
 static void __init cpu_enable_directed_irq(void *unused)
 {
 	union zpci_sic_iib iib = {{0}};
+	union zpci_sic_iib ziib = {{0}};
 
 	iib.cdiib.dibv_addr = (u64) zpci_ibv[smp_processor_id()]->vector;
 
-	__zpci_set_irq_ctrl(SIC_IRQ_MODE_SET_CPU, 0, &iib);
-	zpci_set_irq_ctrl(SIC_IRQ_MODE_D_SINGLE, PCI_ISC);
+	zpci_set_irq_ctrl(SIC_IRQ_MODE_SET_CPU, 0, &iib);
+	zpci_set_irq_ctrl(SIC_IRQ_MODE_D_SINGLE, PCI_ISC, &ziib);
 }
 
 static int __init zpci_directed_irq_init(void)
@@ -407,14 +423,14 @@
 	union zpci_sic_iib iib = {{0}};
 	unsigned int cpu;
 
-	zpci_sbv = airq_iv_create(num_possible_cpus(), 0);
+	zpci_sbv = airq_iv_create(num_possible_cpus(), 0, NULL);
 	if (!zpci_sbv)
 		return -ENOMEM;
 
 	iib.diib.isc = PCI_ISC;
 	iib.diib.nr_cpus = num_possible_cpus();
-	iib.diib.disb_addr = (u64) zpci_sbv->vector;
-	__zpci_set_irq_ctrl(SIC_IRQ_MODE_DIRECT, 0, &iib);
+	iib.diib.disb_addr = virt_to_phys(zpci_sbv->vector);
+	zpci_set_irq_ctrl(SIC_IRQ_MODE_DIRECT, 0, &iib);
 
 	zpci_ibv = kcalloc(num_possible_cpus(), sizeof(*zpci_ibv),
 			   GFP_KERNEL);
@@ -429,7 +445,7 @@
 		zpci_ibv[cpu] = airq_iv_create(cache_line_size() * BITS_PER_BYTE,
 					       AIRQ_IV_DATA |
 					       AIRQ_IV_CACHELINE |
-					       (!cpu ? AIRQ_IV_ALLOC : 0));
+					       (!cpu ? AIRQ_IV_ALLOC : 0), NULL);
 		if (!zpci_ibv[cpu])
 			return -ENOMEM;
 	}
@@ -446,7 +462,7 @@
 	if (!zpci_ibv)
 		return -ENOMEM;
 
-	zpci_sbv = airq_iv_create(ZPCI_NR_DEVICES, AIRQ_IV_ALLOC);
+	zpci_sbv = airq_iv_create(ZPCI_NR_DEVICES, AIRQ_IV_ALLOC, NULL);
 	if (!zpci_sbv)
 		goto out_free;
 
@@ -459,6 +475,7 @@
 
 int __init zpci_irq_init(void)
 {
+	union zpci_sic_iib iib = {{0}};
 	int rc;
 
 	irq_delivery = sclp.has_dirq ? DIRECTED : FLOATING;
@@ -490,7 +507,7 @@
 	 * Enable floating IRQs (with suppression after one IRQ). When using
 	 * directed IRQs this enables the fallback path.
 	 */
-	zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, PCI_ISC);
+	zpci_set_irq_ctrl(SIC_IRQ_MODE_SINGLE, PCI_ISC, &iib);
 
 	return 0;
 out_airq:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_kvm_hook.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_kvm_hook.c
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * VFIO ZPCI devices support
+ *
+ * Copyright (C) IBM Corp. 2022.  All rights reserved.
+ *	Author(s): Pierre Morel <pmorel@linux.ibm.com>
+ */
+#include <linux/kvm_host.h>
+
+struct zpci_kvm_hook zpci_kvm_hook;
+EXPORT_SYMBOL_GPL(zpci_kvm_hook);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_mmio.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_mmio.c
@@ -63,7 +63,7 @@
 	asm volatile (
 		"       sacf    256\n"
 		"0:     llgc    %[tmp],0(%[src])\n"
-		"       sllg    %[val],%[val],8\n"
+		"4:	sllg	%[val],%[val],8\n"
 		"       aghi    %[src],1\n"
 		"       ogr     %[val],%[tmp]\n"
 		"       brctg   %[cnt],0b\n"
@@ -71,7 +71,7 @@
 		"2:     ipm     %[cc]\n"
 		"       srl     %[cc],28\n"
 		"3:     sacf    768\n"
-		EX_TABLE(0b, 3b) EX_TABLE(1b, 3b) EX_TABLE(2b, 3b)
+		EX_TABLE(0b, 3b) EX_TABLE(4b, 3b) EX_TABLE(1b, 3b) EX_TABLE(2b, 3b)
 		:
 		[src] "+a" (src), [cnt] "+d" (cnt),
 		[val] "+d" (val), [tmp] "=d" (tmp),
@@ -96,9 +96,9 @@
 		return -EINVAL;
 
 	while (n > 0) {
-		size = zpci_get_max_write_size((u64 __force) dst,
-					       (u64 __force) src, n,
-					       ZPCI_MAX_WRITE_SIZE);
+		size = zpci_get_max_io_size((u64 __force) dst,
+					    (u64 __force) src, n,
+					    ZPCI_MAX_WRITE_SIZE);
 		if (size > 8) /* main path */
 			rc = __pcistb_mio_inuser(dst, src, size, &status);
 		else
@@ -214,10 +214,10 @@
 		"2:     ahi     %[shift],-8\n"
 		"       srlg    %[tmp],%[val],0(%[shift])\n"
 		"3:     stc     %[tmp],0(%[dst])\n"
-		"       aghi    %[dst],1\n"
+		"5:	aghi	%[dst],1\n"
 		"       brctg   %[cnt],2b\n"
 		"4:     sacf    768\n"
-		EX_TABLE(0b, 4b) EX_TABLE(1b, 4b) EX_TABLE(3b, 4b)
+		EX_TABLE(0b, 4b) EX_TABLE(1b, 4b) EX_TABLE(3b, 4b) EX_TABLE(5b, 4b)
 		:
 		[ioaddr_len] "+&d" (ioaddr_len.pair),
 		[cc] "+d" (cc), [val] "=d" (val),
@@ -241,9 +241,9 @@
 	u8 status;
 
 	while (n > 0) {
-		size = zpci_get_max_write_size((u64 __force) src,
-					       (u64 __force) dst, n,
-					       ZPCI_MAX_READ_SIZE);
+		size = zpci_get_max_io_size((u64 __force) src,
+					    (u64 __force) dst, n,
+					    ZPCI_MAX_READ_SIZE);
 		rc = __pcilg_mio_inuser(dst, src, size, &status);
 		if (rc)
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/pci/pci_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/pci/pci_sysfs.c
@@ -90,6 +90,14 @@
 
 		if (zdev_enabled(zdev)) {
 			ret = zpci_disable_device(zdev);
+			/*
+			 * Due to a z/VM vs LPAR inconsistency in the error
+			 * state the FH may indicate an enabled device but
+			 * disable says the device is already disabled don't
+			 * treat it as an error here.
+			 */
+			if (ret == -EINVAL)
+				ret = 0;
 			if (ret)
 				goto out;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/purgatory/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/purgatory/Makefile
@@ -26,6 +26,7 @@
 KBUILD_CFLAGS += -fno-zero-initialized-in-bss -fno-builtin -ffreestanding
 KBUILD_CFLAGS += -c -MD -Os -m64 -msoft-float -fno-common
 KBUILD_CFLAGS += -fno-stack-protector
+KBUILD_CFLAGS += -DDISABLE_BRANCH_PROFILING
 KBUILD_CFLAGS += $(CLANG_FLAGS)
 KBUILD_CFLAGS += $(call cc-option,-fno-PIE)
 KBUILD_AFLAGS := $(filter-out -DCC_USING_EXPOLINE,$(KBUILD_AFLAGS))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/s390/tools/gcc-thunk-extern.sh
+++ linux-xilinx-zynqmp-5.15.0/arch/s390/tools/gcc-thunk-extern.sh
@@ -0,0 +1,24 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0
+# Borrowed from gcc: gcc/testsuite/gcc.target/s390/nobp-section-type-conflict.c
+# Checks that we don't get error: section type conflict with ‘put_page’.
+
+cat << "END" | $@ -x c - -fno-PIE -march=z10 -mindirect-branch=thunk-extern -mfunction-return=thunk-extern -mindirect-branch-table -O2 -c -o /dev/null
+int a;
+int b (void);
+void c (int);
+
+static void
+put_page (void)
+{
+  if (b ())
+    c (a);
+}
+
+__attribute__ ((__section__ (".init.text"), __cold__)) void
+d (void)
+{
+  put_page ();
+  put_page ();
+}
+END
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/Kconfig
@@ -7,6 +7,7 @@
 	select ARCH_HAVE_CUSTOM_GPIO_H
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG if (GUSA_RB || CPU_SH4A)
 	select ARCH_HAS_BINFMT_FLAT if !MMU
+	select ARCH_HAS_CPU_FINALIZE_INIT
 	select ARCH_HAS_GIGANTIC_PAGE
 	select ARCH_HAS_GCOV_PROFILE_ALL
 	select ARCH_HAS_PTE_SPECIAL
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/Kconfig.debug
@@ -15,13 +15,24 @@
 
 config STACK_DEBUG
 	bool "Check for stack overflows"
-	depends on DEBUG_KERNEL
+	depends on DEBUG_KERNEL && PRINTK
 	help
 	  This option will cause messages to be printed if free stack space
 	  drops below a certain limit. Saying Y here will add overhead to
 	  every function call and will therefore incur a major
 	  performance hit. Most users should say N.
 
+config EARLY_PRINTK
+	bool "Early printk"
+	depends on SH_STANDARD_BIOS
+	help
+	  Say Y here to redirect kernel printk messages to the serial port
+	  used by the SH-IPL bootloader, starting very early in the boot
+	  process and ending when the kernel's serial console is initialised.
+	  This option is only useful while porting the kernel to a new machine,
+	  when the kernel may crash or hang before the serial console is
+	  initialised.  If unsure, say N.
+
 config 4KSTACKS
 	bool "Use 4Kb for kernel stacks instead of 8Kb"
 	depends on DEBUG_KERNEL && (MMU || BROKEN) && !PAGE_SIZE_64KB
@@ -54,6 +65,7 @@
 
 config DWARF_UNWINDER
 	bool "Enable the DWARF unwinder for stacktraces"
+	depends on DEBUG_KERNEL
 	select FRAME_POINTER
 	default n
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/boards/mach-ap325rxa/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/boards/mach-ap325rxa/setup.c
@@ -530,7 +530,7 @@
 	device_initialize(&ap325rxa_ceu_device.dev);
 	dma_declare_coherent_memory(&ap325rxa_ceu_device.dev,
 			ceu_dma_membase, ceu_dma_membase,
-			ceu_dma_membase + CEU_BUFFER_MEMORY_SIZE - 1);
+			CEU_BUFFER_MEMORY_SIZE);
 
 	platform_device_add(&ap325rxa_ceu_device);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/boards/mach-ecovec24/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/boards/mach-ecovec24/setup.c
@@ -1454,15 +1454,13 @@
 	device_initialize(&ecovec_ceu_devices[0]->dev);
 	dma_declare_coherent_memory(&ecovec_ceu_devices[0]->dev,
 				    ceu0_dma_membase, ceu0_dma_membase,
-				    ceu0_dma_membase +
-				    CEU_BUFFER_MEMORY_SIZE - 1);
+				    CEU_BUFFER_MEMORY_SIZE);
 	platform_device_add(ecovec_ceu_devices[0]);
 
 	device_initialize(&ecovec_ceu_devices[1]->dev);
 	dma_declare_coherent_memory(&ecovec_ceu_devices[1]->dev,
 				    ceu1_dma_membase, ceu1_dma_membase,
-				    ceu1_dma_membase +
-				    CEU_BUFFER_MEMORY_SIZE - 1);
+				    CEU_BUFFER_MEMORY_SIZE);
 	platform_device_add(ecovec_ceu_devices[1]);
 
 	gpiod_add_lookup_table(&cn12_power_gpiod_table);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/boards/mach-kfr2r09/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/boards/mach-kfr2r09/setup.c
@@ -603,7 +603,7 @@
 	device_initialize(&kfr2r09_ceu_device.dev);
 	dma_declare_coherent_memory(&kfr2r09_ceu_device.dev,
 			ceu_dma_membase, ceu_dma_membase,
-			ceu_dma_membase + CEU_BUFFER_MEMORY_SIZE - 1);
+			CEU_BUFFER_MEMORY_SIZE);
 
 	platform_device_add(&kfr2r09_ceu_device);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/boards/mach-migor/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/boards/mach-migor/setup.c
@@ -604,7 +604,7 @@
 	device_initialize(&migor_ceu_device.dev);
 	dma_declare_coherent_memory(&migor_ceu_device.dev,
 			ceu_dma_membase, ceu_dma_membase,
-			ceu_dma_membase + CEU_BUFFER_MEMORY_SIZE - 1);
+			CEU_BUFFER_MEMORY_SIZE);
 
 	platform_device_add(&migor_ceu_device);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/boards/mach-se/7724/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/boards/mach-se/7724/setup.c
@@ -940,15 +940,13 @@
 	device_initialize(&ms7724se_ceu_devices[0]->dev);
 	dma_declare_coherent_memory(&ms7724se_ceu_devices[0]->dev,
 				    ceu0_dma_membase, ceu0_dma_membase,
-				    ceu0_dma_membase +
-				    CEU_BUFFER_MEMORY_SIZE - 1);
+				    CEU_BUFFER_MEMORY_SIZE);
 	platform_device_add(ms7724se_ceu_devices[0]);
 
 	device_initialize(&ms7724se_ceu_devices[1]->dev);
 	dma_declare_coherent_memory(&ms7724se_ceu_devices[1]->dev,
 				    ceu1_dma_membase, ceu1_dma_membase,
-				    ceu1_dma_membase +
-				    CEU_BUFFER_MEMORY_SIZE - 1);
+				    CEU_BUFFER_MEMORY_SIZE);
 	platform_device_add(ms7724se_ceu_devices[1]);
 
 	return platform_add_devices(ms7724se_devices,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/configs/titan_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/configs/titan_defconfig
@@ -242,7 +242,6 @@
 CONFIG_NFSD_V3=y
 CONFIG_SMB_FS=m
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_ASCII=m
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/drivers/dma/dma-sh.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/drivers/dma/dma-sh.c
@@ -19,6 +19,18 @@
 #include <cpu/dma.h>
 
 /*
+ * Some of the SoCs feature two DMAC modules. In such a case, the channels are
+ * distributed equally among them.
+ */
+#ifdef	SH_DMAC_BASE1
+#define	SH_DMAC_NR_MD_CH	(CONFIG_NR_ONCHIP_DMA_CHANNELS / 2)
+#else
+#define	SH_DMAC_NR_MD_CH	CONFIG_NR_ONCHIP_DMA_CHANNELS
+#endif
+
+#define	SH_DMAC_CH_SZ		0x10
+
+/*
  * Define the default configuration for dual address memory-memory transfer.
  * The 0x400 value represents auto-request, external->external.
  */
@@ -29,7 +41,7 @@
 	unsigned long base = SH_DMAC_BASE0;
 
 #ifdef SH_DMAC_BASE1
-	if (chan >= 6)
+	if (chan >= SH_DMAC_NR_MD_CH)
 		base = SH_DMAC_BASE1;
 #endif
 
@@ -40,13 +52,13 @@
 {
 	unsigned long base = dma_find_base(chan);
 
-	/* Normalize offset calculation */
-	if (chan >= 9)
-		chan -= 6;
-	if (chan >= 4)
-		base += 0x10;
+	chan = (chan % SH_DMAC_NR_MD_CH) * SH_DMAC_CH_SZ;
+
+	/* DMAOR is placed inside the channel register space. Step over it. */
+	if (chan >= DMAOR)
+		base += SH_DMAC_CH_SZ;
 
-	return base + (chan * 0x10);
+	return base + chan;
 }
 
 #ifdef CONFIG_SH_DMA_IRQ_MULTI
@@ -250,12 +262,11 @@
 #define NR_DMAOR	1
 #endif
 
-/*
- * DMAOR bases are broken out amongst channel groups. DMAOR0 manages
- * channels 0 - 5, DMAOR1 6 - 11 (optional).
- */
-#define dmaor_read_reg(n)		__raw_readw(dma_find_base((n)*6))
-#define dmaor_write_reg(n, data)	__raw_writew(data, dma_find_base(n)*6)
+#define dmaor_read_reg(n)		__raw_readw(dma_find_base((n) * \
+						    SH_DMAC_NR_MD_CH) + DMAOR)
+#define dmaor_write_reg(n, data)	__raw_writew(data, \
+						     dma_find_base((n) * \
+						     SH_DMAC_NR_MD_CH) + DMAOR)
 
 static inline int dmaor_reset(int no)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/drivers/push-switch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/drivers/push-switch.c
@@ -101,8 +101,8 @@
 		device_remove_file(&pdev->dev, &dev_attr_switch);
 
 	platform_set_drvdata(pdev, NULL);
-	flush_work(&psw->work);
 	del_timer_sync(&psw->debounce);
+	flush_work(&psw->work);
 	free_irq(irq, pdev);
 
 	kfree(psw);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/include/asm/io.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/include/asm/io.h
@@ -271,8 +271,12 @@
 #endif /* CONFIG_HAVE_IOREMAP_PROT */
 
 #else /* CONFIG_MMU */
-#define iounmap(addr)		do { } while (0)
-#define ioremap(offset, size)	((void __iomem *)(unsigned long)(offset))
+static inline void __iomem *ioremap(phys_addr_t offset, size_t size)
+{
+	return (void __iomem *)(unsigned long)offset;
+}
+
+static inline void iounmap(volatile void __iomem *addr) { }
 #endif /* CONFIG_MMU */
 
 #define ioremap_uc	ioremap
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/include/asm/kprobes.h
@@ -26,7 +26,7 @@
 struct kprobe;
 
 void arch_remove_kprobe(struct kprobe *);
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 
 /* Architecture specific copy of original instruction*/
 struct arch_specific_insn {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/include/asm/processor.h
@@ -167,6 +167,8 @@
 #define instruction_size(insn)	(2)
 #endif
 
+void select_idle_routine(void);
+
 #endif /* __ASSEMBLY__ */
 
 #include <asm/processor_32.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/include/asm/processor_32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/include/asm/processor_32.h
@@ -50,6 +50,7 @@
 #define SR_FD		0x00008000
 #define SR_MD		0x40000000
 
+#define SR_USER_MASK	0x00000303	// M, Q, S, T bits
 /*
  * DSP structure and data
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/include/asm/sections.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/include/asm/sections.h
@@ -4,7 +4,7 @@
 
 #include <asm-generic/sections.h>
 
-extern long __machvec_start, __machvec_end;
+extern char __machvec_start[], __machvec_end[];
 extern char __uncached_start, __uncached_end;
 extern char __start_eh_frame[], __stop_eh_frame[];
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/include/asm/sfp-machine.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/include/asm/sfp-machine.h
@@ -13,6 +13,14 @@
 #ifndef _SFP_MACHINE_H
 #define _SFP_MACHINE_H
 
+#ifdef __BIG_ENDIAN__
+#define __BYTE_ORDER __BIG_ENDIAN
+#define __LITTLE_ENDIAN 0
+#else
+#define __BYTE_ORDER __LITTLE_ENDIAN
+#define __BIG_ENDIAN 0
+#endif
+
 #define _FP_W_TYPE_SIZE		32
 #define _FP_W_TYPE		unsigned long
 #define _FP_WS_TYPE		signed long
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/cpu/fpu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/cpu/fpu.c
@@ -62,18 +62,20 @@
 	}
 
 	if (!tsk_used_math(tsk)) {
-		local_irq_enable();
+		int ret;
 		/*
 		 * does a slab alloc which can sleep
 		 */
-		if (init_fpu(tsk)) {
+		local_irq_enable();
+		ret = init_fpu(tsk);
+		local_irq_disable();
+		if (ret) {
 			/*
 			 * ran out of memory!
 			 */
-			do_group_exit(SIGKILL);
+			force_sig(SIGKILL);
 			return;
 		}
-		local_irq_disable();
 	}
 
 	grab_fpu(regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/cpu/proc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/cpu/proc.c
@@ -132,7 +132,7 @@
 
 static void *c_start(struct seq_file *m, loff_t *pos)
 {
-	return *pos < NR_CPUS ? cpu_data + *pos : NULL;
+	return *pos < nr_cpu_ids ? cpu_data + *pos : NULL;
 }
 static void *c_next(struct seq_file *m, void *v, loff_t *pos)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/cpu/sh2/probe.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/cpu/sh2/probe.c
@@ -21,7 +21,7 @@
 	if (!of_flat_dt_is_compatible(node, "jcore,cache"))
 		return 0;
 
-	j2_ccr_base = (u32 __iomem *)of_flat_dt_translate_address(node);
+	j2_ccr_base = ioremap(of_flat_dt_translate_address(node), 4);
 
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/cpu/sh4/sq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/cpu/sh4/sq.c
@@ -381,7 +381,7 @@
 	if (unlikely(!sq_cache))
 		return ret;
 
-	sq_bitmap = kzalloc(size, GFP_KERNEL);
+	sq_bitmap = kcalloc(size, sizeof(long), GFP_KERNEL);
 	if (unlikely(!sq_bitmap))
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/cpu/sh4a/smp-shx3.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/cpu/sh4a/smp-shx3.c
@@ -73,8 +73,9 @@
 	BUILD_BUG_ON(SMP_MSG_NR >= 8);
 
 	for (i = 0; i < SMP_MSG_NR; i++)
-		request_irq(104 + i, ipi_interrupt_handler,
-			    IRQF_PERCPU, "IPI", (void *)(long)i);
+		if (request_irq(104 + i, ipi_interrupt_handler,
+			    IRQF_PERCPU, "IPI", (void *)(long)i))
+			pr_err("Failed to request irq %d\n", i);
 
 	for (i = 0; i < max_cpus; i++)
 		set_cpu_present(i, true);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/head_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/head_32.S
@@ -64,7 +64,7 @@
 	ldc	r0, r6_bank
 #endif
 
-#ifdef CONFIG_OF_FLATTREE
+#ifdef CONFIG_OF_EARLY_FLATTREE
 	mov	r4, r12		! Store device tree blob pointer in r12
 #endif
 	
@@ -315,7 +315,7 @@
 10:		
 #endif
 
-#ifdef CONFIG_OF_FLATTREE
+#ifdef CONFIG_OF_EARLY_FLATTREE
 	mov.l	8f, r0		! Make flat device tree available early.
 	jsr	@r0
 	 mov	r12, r4
@@ -346,7 +346,7 @@
 5:	.long	start_kernel
 6:	.long	cpu_init
 7:	.long	init_thread_union
-#if defined(CONFIG_OF_FLATTREE)
+#if defined(CONFIG_OF_EARLY_FLATTREE)
 8:	.long	sh_fdt_init
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/idle.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/idle.c
@@ -14,6 +14,7 @@
 #include <linux/irqflags.h>
 #include <linux/smp.h>
 #include <linux/atomic.h>
+#include <asm/processor.h>
 #include <asm/smp.h>
 #include <asm/bl_bit.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/kprobes.c
@@ -44,17 +44,12 @@
 	if (OPCODE_RTE(opcode))
 		return -EFAULT;	/* Bad breakpoint */
 
+	memcpy(p->ainsn.insn, p->addr, MAX_INSN_SIZE * sizeof(kprobe_opcode_t));
 	p->opcode = opcode;
 
 	return 0;
 }
 
-void __kprobes arch_copy_kprobe(struct kprobe *p)
-{
-	memcpy(p->ainsn.insn, p->addr, MAX_INSN_SIZE * sizeof(kprobe_opcode_t));
-	p->opcode = *p->addr;
-}
-
 void __kprobes arch_arm_kprobe(struct kprobe *p)
 {
 	*p->addr = BREAKPOINT_INSTRUCTION;
@@ -207,7 +202,7 @@
 	ri->fp = NULL;
 
 	/* Replace the return addr with trampoline addr */
-	regs->pr = (unsigned long)kretprobe_trampoline;
+	regs->pr = (unsigned long)__kretprobe_trampoline;
 }
 
 static int __kprobes kprobe_handler(struct pt_regs *regs)
@@ -293,17 +288,17 @@
  */
 static void __used kretprobe_trampoline_holder(void)
 {
-	asm volatile (".globl kretprobe_trampoline\n"
-		      "kretprobe_trampoline:\n\t"
+	asm volatile (".globl __kretprobe_trampoline\n"
+		      "__kretprobe_trampoline:\n\t"
 		      "nop\n");
 }
 
 /*
- * Called when we hit the probe point at kretprobe_trampoline
+ * Called when we hit the probe point at __kretprobe_trampoline
  */
 int __kprobes trampoline_probe_handler(struct kprobe *p, struct pt_regs *regs)
 {
-	regs->pc = __kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	regs->pc = __kretprobe_trampoline_handler(regs, NULL);
 
 	return 1;
 }
@@ -442,7 +437,7 @@
 }
 
 static struct kprobe trampoline_p = {
-	.addr = (kprobe_opcode_t *)&kretprobe_trampoline,
+	.addr = (kprobe_opcode_t *)&__kretprobe_trampoline,
 	.pre_handler = trampoline_probe_handler
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/machvec.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/machvec.c
@@ -20,8 +20,8 @@
 #define MV_NAME_SIZE 32
 
 #define for_each_mv(mv) \
-	for ((mv) = (struct sh_machine_vector *)&__machvec_start; \
-	     (mv) && (unsigned long)(mv) < (unsigned long)&__machvec_end; \
+	for ((mv) = (struct sh_machine_vector *)__machvec_start; \
+	     (mv) && (unsigned long)(mv) < (unsigned long)__machvec_end; \
 	     (mv)++)
 
 static struct sh_machine_vector * __init get_mv_byname(const char *name)
@@ -87,8 +87,8 @@
 	if (!machvec_selected) {
 		unsigned long machvec_size;
 
-		machvec_size = ((unsigned long)&__machvec_end -
-				(unsigned long)&__machvec_start);
+		machvec_size = ((unsigned long)__machvec_end -
+				(unsigned long)__machvec_start);
 
 		/*
 		 * Sanity check for machvec section alignment. Ensure
@@ -102,7 +102,7 @@
 		 * vector (usually the only one) from .machvec.init.
 		 */
 		if (machvec_size >= sizeof(struct sh_machine_vector))
-			sh_mv = *(struct sh_machine_vector *)&__machvec_start;
+			sh_mv = *(struct sh_machine_vector *)__machvec_start;
 	}
 
 	pr_notice("Booting machvec: %s\n", get_system_type());
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/nmi_debug.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/nmi_debug.c
@@ -49,7 +49,7 @@
 	register_die_notifier(&nmi_debug_nb);
 
 	if (*str != '=')
-		return 0;
+		return 1;
 
 	for (p = str + 1; *p; p = sep + 1) {
 		sep = strchr(p, ',');
@@ -70,6 +70,6 @@
 			break;
 	}
 
-	return 0;
+	return 1;
 }
 __setup("nmi_debug", nmi_debug_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/setup.c
@@ -43,6 +43,7 @@
 #include <asm/smp.h>
 #include <asm/mmu_context.h>
 #include <asm/mmzone.h>
+#include <asm/processor.h>
 #include <asm/sparsemem.h>
 #include <asm/platform_early.h>
 
@@ -244,7 +245,7 @@
 {
 }
 
-#ifdef CONFIG_OF_FLATTREE
+#ifdef CONFIG_OF_EARLY_FLATTREE
 void __ref sh_fdt_init(phys_addr_t dt_phys)
 {
 	static int done = 0;
@@ -326,7 +327,7 @@
 	/* Let earlyprintk output early console messages */
 	sh_early_platform_driver_probe("earlyprintk", 1, 1);
 
-#ifdef CONFIG_OF_FLATTREE
+#ifdef CONFIG_OF_EARLY_FLATTREE
 #ifdef CONFIG_USE_BUILTIN_DTB
 	unflatten_and_copy_device_tree();
 #else
@@ -354,3 +355,57 @@
 {
 	return sh_mv.mv_mode_pins() & pin;
 }
+
+void __init arch_cpu_finalize_init(void)
+{
+	char *p = &init_utsname()->machine[2]; /* "sh" */
+
+	select_idle_routine();
+
+	current_cpu_data.loops_per_jiffy = loops_per_jiffy;
+
+	switch (current_cpu_data.family) {
+	case CPU_FAMILY_SH2:
+		*p++ = '2';
+		break;
+	case CPU_FAMILY_SH2A:
+		*p++ = '2';
+		*p++ = 'a';
+		break;
+	case CPU_FAMILY_SH3:
+		*p++ = '3';
+		break;
+	case CPU_FAMILY_SH4:
+		*p++ = '4';
+		break;
+	case CPU_FAMILY_SH4A:
+		*p++ = '4';
+		*p++ = 'a';
+		break;
+	case CPU_FAMILY_SH4AL_DSP:
+		*p++ = '4';
+		*p++ = 'a';
+		*p++ = 'l';
+		*p++ = '-';
+		*p++ = 'd';
+		*p++ = 's';
+		*p++ = 'p';
+		break;
+	case CPU_FAMILY_UNKNOWN:
+		/*
+		 * Specifically use CPU_FAMILY_UNKNOWN rather than
+		 * default:, so we're able to have the compiler whine
+		 * about unhandled enumerations.
+		 */
+		break;
+	}
+
+	pr_info("CPU: %s\n", get_cpu_subtype(&current_cpu_data));
+
+#ifndef __LITTLE_ENDIAN__
+	/* 'eb' means 'Endian Big' */
+	*p++ = 'e';
+	*p++ = 'b';
+#endif
+	*p = '\0';
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/signal_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/signal_32.c
@@ -115,6 +115,7 @@
 restore_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc, int *r0_p)
 {
 	unsigned int err = 0;
+	unsigned int sr = regs->sr & ~SR_USER_MASK;
 
 #define COPY(x)		err |= __get_user(regs->x, &sc->sc_##x)
 			COPY(regs[1]);
@@ -130,6 +131,8 @@
 	COPY(sr);	COPY(pc);
 #undef COPY
 
+	regs->sr = (regs->sr & SR_USER_MASK) | sr;
+
 #ifdef CONFIG_SH_FPU
 	if (boot_cpu_data.flags & CPU_HAS_FPU) {
 		int owned_fp;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/sys_sh32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/sys_sh32.c
@@ -59,3 +59,14 @@
 				 (u64)len0 << 32 | len1, advice);
 #endif
 }
+
+/*
+ * swap the arguments the way that libc wants them instead of
+ * moving flags ahead of the 64-bit nbytes argument
+ */
+SYSCALL_DEFINE6(sh_sync_file_range6, int, fd, SC_ARG64(offset),
+                SC_ARG64(nbytes), unsigned int, flags)
+{
+        return ksys_sync_file_range(fd, SC_VAL64(loff_t, offset),
+                                    SC_VAL64(loff_t, nbytes), flags);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/syscalls/syscall.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/syscalls/syscall.tbl
@@ -321,7 +321,7 @@
 311	common	set_robust_list			sys_set_robust_list
 312	common	get_robust_list			sys_get_robust_list
 313	common	splice				sys_splice
-314	common	sync_file_range			sys_sync_file_range
+314	common	sync_file_range			sys_sh_sync_file_range6
 315	common	tee				sys_tee
 316	common	vmsplice			sys_vmsplice
 317	common	move_pages			sys_move_pages
@@ -395,6 +395,7 @@
 385	common	pkey_alloc			sys_pkey_alloc
 386	common	pkey_free			sys_pkey_free
 387	common	rseq				sys_rseq
+388	common	sync_file_range2		sys_sync_file_range2
 # room for arch specific syscalls
 393	common	semget				sys_semget
 394	common	semctl				sys_semctl
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/traps.c
@@ -57,7 +57,7 @@
 	if (panic_on_oops)
 		panic("Fatal exception");
 
-	do_exit(SIGSEGV);
+	make_task_dead(SIGSEGV);
 }
 
 void die_if_kernel(const char *str, struct pt_regs *regs, long err)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/kernel/vmlinux.lds.S
@@ -4,6 +4,7 @@
  * Written by Niibe Yutaka and Paul Mundt
  */
 OUTPUT_ARCH(sh)
+#define RUNTIME_DISCARD_EXIT
 #include <asm/thread_info.h>
 #include <asm/cache.h>
 #include <asm/vmlinux.lds.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/lib/checksum.S
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/lib/checksum.S
@@ -33,7 +33,8 @@
  */
 
 /*	
- * asmlinkage __wsum csum_partial(const void *buf, int len, __wsum sum);
+ * unsigned int csum_partial(const unsigned char *buf, int len,
+ *                           unsigned int sum);
  */
 
 .text
@@ -45,31 +46,11 @@
 	   * Fortunately, it is easy to convert 2-byte alignment to 4-byte
 	   * alignment for the unrolled loop.
 	   */
+	mov	r5, r1
 	mov	r4, r0
-	tst	#3, r0		! Check alignment.
-	bt/s	2f		! Jump if alignment is ok.
-	 mov	r4, r7		! Keep a copy to check for alignment
+	tst	#2, r0		! Check alignment.
+	bt	2f		! Jump if alignment is ok.
 	!
-	tst	#1, r0		! Check alignment.
-	bt	21f		! Jump if alignment is boundary of 2bytes.
-
-	! buf is odd
-	tst	r5, r5
-	add	#-1, r5
-	bt	9f
-	mov.b	@r4+, r0
-	extu.b	r0, r0
-	addc	r0, r6		! t=0 from previous tst
-	mov	r6, r0
-	shll8	r6
-	shlr16	r0
-	shlr8	r0
-	or	r0, r6
-	mov	r4, r0
-	tst	#2, r0
-	bt	2f
-21:
-	! buf is 2 byte aligned (len could be 0)
 	add	#-2, r5		! Alignment uses up two bytes.
 	cmp/pz	r5		!
 	bt/s	1f		! Jump if we had at least two bytes.
@@ -77,17 +58,16 @@
 	bra	6f
 	 add	#2, r5		! r5 was < 2.  Deal with it.
 1:
+	mov	r5, r1		! Save new len for later use.
 	mov.w	@r4+, r0
 	extu.w	r0, r0
 	addc	r0, r6
 	bf	2f
 	add	#1, r6
 2:
-	! buf is 4 byte aligned (len could be 0)
-	mov	r5, r1
 	mov	#-5, r0
-	shld	r0, r1
-	tst	r1, r1
+	shld	r0, r5
+	tst	r5, r5
 	bt/s	4f		! if it's =0, go to 4f
 	 clrt
 	.align	2
@@ -109,31 +89,30 @@
 	addc	r0, r6
 	addc	r2, r6
 	movt	r0
-	dt	r1
+	dt	r5
 	bf/s	3b
 	 cmp/eq	#1, r0
-	! here, we know r1==0
-	addc	r1, r6			! add carry to r6
+	! here, we know r5==0
+	addc	r5, r6			! add carry to r6
 4:
-	mov	r5, r0
+	mov	r1, r0
 	and	#0x1c, r0
 	tst	r0, r0
-	bt	6f
-	! 4 bytes or more remaining
-	mov	r0, r1
-	shlr2	r1
+	bt/s	6f
+	 mov	r0, r5
+	shlr2	r5
 	mov	#0, r2
 5:
 	addc	r2, r6
 	mov.l	@r4+, r2
 	movt	r0
-	dt	r1
+	dt	r5
 	bf/s	5b
 	 cmp/eq	#1, r0
 	addc	r2, r6
-	addc	r1, r6		! r1==0 here, so it means add carry-bit
+	addc	r5, r6		! r5==0 here, so it means add carry-bit
 6:
-	! 3 bytes or less remaining
+	mov	r1, r5
 	mov	#3, r0
 	and	r0, r5
 	tst	r5, r5
@@ -159,16 +138,6 @@
 	mov	#0, r0
 	addc	r0, r6
 9:
-	! Check if the buffer was misaligned, if so realign sum
-	mov	r7, r0
-	tst	#1, r0
-	bt	10f
-	mov	r6, r0
-	shll8	r6
-	shlr16	r0
-	shlr8	r0
-	or	r0, r6
-10:
 	rts
 	 mov	r6, r0
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/math-emu/math.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/math-emu/math.c
@@ -468,109 +468,6 @@
 }
 
 /**
- *	denormal_to_double - Given denormalized float number,
- *	                     store double float
- *
- *	@fpu: Pointer to sh_fpu_soft structure
- *	@n: Index to FP register
- */
-static void denormal_to_double(struct sh_fpu_soft_struct *fpu, int n)
-{
-	unsigned long du, dl;
-	unsigned long x = fpu->fpul;
-	int exp = 1023 - 126;
-
-	if (x != 0 && (x & 0x7f800000) == 0) {
-		du = (x & 0x80000000);
-		while ((x & 0x00800000) == 0) {
-			x <<= 1;
-			exp--;
-		}
-		x &= 0x007fffff;
-		du |= (exp << 20) | (x >> 3);
-		dl = x << 29;
-
-		fpu->fp_regs[n] = du;
-		fpu->fp_regs[n+1] = dl;
-	}
-}
-
-/**
- *	ieee_fpe_handler - Handle denormalized number exception
- *
- *	@regs: Pointer to register structure
- *
- *	Returns 1 when it's handled (should not cause exception).
- */
-static int ieee_fpe_handler(struct pt_regs *regs)
-{
-	unsigned short insn = *(unsigned short *)regs->pc;
-	unsigned short finsn;
-	unsigned long nextpc;
-	int nib[4] = {
-		(insn >> 12) & 0xf,
-		(insn >> 8) & 0xf,
-		(insn >> 4) & 0xf,
-		insn & 0xf};
-
-	if (nib[0] == 0xb ||
-	    (nib[0] == 0x4 && nib[2] == 0x0 && nib[3] == 0xb)) /* bsr & jsr */
-		regs->pr = regs->pc + 4;
-
-	if (nib[0] == 0xa || nib[0] == 0xb) { /* bra & bsr */
-		nextpc = regs->pc + 4 + ((short) ((insn & 0xfff) << 4) >> 3);
-		finsn = *(unsigned short *) (regs->pc + 2);
-	} else if (nib[0] == 0x8 && nib[1] == 0xd) { /* bt/s */
-		if (regs->sr & 1)
-			nextpc = regs->pc + 4 + ((char) (insn & 0xff) << 1);
-		else
-			nextpc = regs->pc + 4;
-		finsn = *(unsigned short *) (regs->pc + 2);
-	} else if (nib[0] == 0x8 && nib[1] == 0xf) { /* bf/s */
-		if (regs->sr & 1)
-			nextpc = regs->pc + 4;
-		else
-			nextpc = regs->pc + 4 + ((char) (insn & 0xff) << 1);
-		finsn = *(unsigned short *) (regs->pc + 2);
-	} else if (nib[0] == 0x4 && nib[3] == 0xb &&
-		 (nib[2] == 0x0 || nib[2] == 0x2)) { /* jmp & jsr */
-		nextpc = regs->regs[nib[1]];
-		finsn = *(unsigned short *) (regs->pc + 2);
-	} else if (nib[0] == 0x0 && nib[3] == 0x3 &&
-		 (nib[2] == 0x0 || nib[2] == 0x2)) { /* braf & bsrf */
-		nextpc = regs->pc + 4 + regs->regs[nib[1]];
-		finsn = *(unsigned short *) (regs->pc + 2);
-	} else if (insn == 0x000b) { /* rts */
-		nextpc = regs->pr;
-		finsn = *(unsigned short *) (regs->pc + 2);
-	} else {
-		nextpc = regs->pc + 2;
-		finsn = insn;
-	}
-
-	if ((finsn & 0xf1ff) == 0xf0ad) { /* fcnvsd */
-		struct task_struct *tsk = current;
-
-		if ((tsk->thread.xstate->softfpu.fpscr & (1 << 17))) {
-			/* FPU error */
-			denormal_to_double (&tsk->thread.xstate->softfpu,
-					    (finsn >> 8) & 0xf);
-			tsk->thread.xstate->softfpu.fpscr &=
-				~(FPSCR_CAUSE_MASK | FPSCR_FLAG_MASK);
-			task_thread_info(tsk)->status |= TS_USEDFPU;
-		} else {
-			force_sig_fault(SIGFPE, FPE_FLTINV,
-					(void __user *)regs->pc);
-		}
-
-		regs->pc = nextpc;
-		return 1;
-	}
-
-	return 0;
-}
-
-/**
  * fpu_init - Initialize FPU registers
  * @fpu: Pointer to software emulated FPU registers.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sh/math-emu/sfp-util.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sh/math-emu/sfp-util.h
@@ -67,7 +67,3 @@
   } while (0)
 
 #define abort()	return 0
-
-#define __BYTE_ORDER __LITTLE_ENDIAN
-
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/Kconfig
@@ -52,6 +52,7 @@
 config SPARC32
 	def_bool !64BIT
 	select ARCH_32BIT_OFF_T
+	select ARCH_HAS_CPU_FINALIZE_INIT if !SMP
 	select ARCH_HAS_SYNC_DMA_FOR_CPU
 	select GENERIC_ATOMIC64
 	select CLZ_TAB
@@ -286,7 +287,7 @@
 	  This config option is actually maximum order plus one. For example,
 	  a value of 13 means that the largest free memory block is 2^12 pages.
 
-if SPARC64
+if SPARC64 || COMPILE_TEST
 source "kernel/power/Kconfig"
 endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/boot/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/boot/Makefile
@@ -22,7 +22,7 @@
 
 # Actual linking
 
-$(obj)/zImage: $(obj)/image
+$(obj)/zImage: $(obj)/image FORCE
 	$(call if_changed,gzip)
 	@echo '  kernel: $@ is ready'
 
@@ -31,7 +31,7 @@
 	@echo '  kernel: $@ is ready'
 else
 
-$(obj)/zImage: $(obj)/image
+$(obj)/zImage: $(obj)/image FORCE
 	$(call if_changed,strip)
 	@echo '  kernel: $@ is ready'
 
@@ -44,7 +44,7 @@
 $(obj)/image.bin: $(obj)/image FORCE
 	$(call if_changed,objcopy)
 
-$(obj)/image.gz: $(obj)/image.bin
+$(obj)/image.gz: $(obj)/image.bin FORCE
 	$(call if_changed,gzip)
 
 UIMAGE_LOADADDR = $(CONFIG_UBOOT_LOAD_ADDR)
@@ -56,7 +56,7 @@
                      -r -b binary $@ -o $@.o
 
 targets += uImage
-$(obj)/uImage: $(obj)/image.gz
+$(obj)/uImage: $(obj)/image.gz FORCE
 	$(call if_changed,uimage)
 	$(call if_changed,uimage.o)
 	@echo '  Image $@ is ready'
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/include/asm/kprobes.h
@@ -24,7 +24,7 @@
 	flushi(&(p)->ainsn.insn[1]);	\
 } while (0)
 
-void kretprobe_trampoline(void);
+void __kretprobe_trampoline(void);
 
 /* Architecture specific copy of original instruction*/
 struct arch_specific_insn {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/include/asm/oplib_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/include/asm/oplib_64.h
@@ -247,6 +247,7 @@
 int prom_ihandle2path(int handle, char *buffer, int bufsize);
 
 /* Client interface level routines. */
+void prom_cif_init(void *cif_handler);
 void p1275_cmd_direct(unsigned long *);
 
 #endif /* !(__SPARC64_OPLIB_H) */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/include/asm/smp_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/include/asm/smp_64.h
@@ -47,7 +47,6 @@
 int hard_smp_processor_id(void);
 #define raw_smp_processor_id() (current_thread_info()->cpu)
 
-void smp_fill_in_cpu_possible_map(void);
 void smp_fill_in_sib_core_maps(void);
 void cpu_play_dead(void);
 
@@ -77,7 +76,6 @@
 #define smp_fill_in_sib_core_maps() do { } while (0)
 #define smp_fetch_global_regs() do { } while (0)
 #define smp_fetch_global_pmu() do { } while (0)
-#define smp_fill_in_cpu_possible_map() do { } while (0)
 #define smp_init_cpu_poke() do { } while (0)
 #define scheduler_poke() do { } while (0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/include/asm/timex_32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/include/asm/timex_32.h
@@ -9,8 +9,6 @@
 
 #define CLOCK_TICK_RATE	1193180 /* Underlying HZ */
 
-/* XXX Maybe do something better at some point... -DaveM */
-typedef unsigned long cycles_t;
-#define get_cycles()	(0)
+#include <asm-generic/timex.h>
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/include/uapi/asm/termbits.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/include/uapi/asm/termbits.h
@@ -13,16 +13,6 @@
 typedef unsigned long   tcflag_t;
 #endif
 
-#define NCC 8
-struct termio {
-	unsigned short c_iflag;		/* input mode flags */
-	unsigned short c_oflag;		/* output mode flags */
-	unsigned short c_cflag;		/* control mode flags */
-	unsigned short c_lflag;		/* local mode flags */
-	unsigned char c_line;		/* line discipline */
-	unsigned char c_cc[NCC];	/* control characters */
-};
-
 #define NCCS 17
 struct termios {
 	tcflag_t c_iflag;		/* input mode flags */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/include/uapi/asm/termios.h
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/include/uapi/asm/termios.h
@@ -40,5 +40,14 @@
 	unsigned short ws_ypixel;
 };
 
+#define NCC 8
+struct termio {
+	unsigned short c_iflag;		/* input mode flags */
+	unsigned short c_oflag;		/* output mode flags */
+	unsigned short c_cflag;		/* control mode flags */
+	unsigned short c_lflag;		/* local mode flags */
+	unsigned char c_line;		/* line discipline */
+	unsigned char c_cc[NCC];	/* control characters */
+};
 
 #endif /* _UAPI_SPARC_TERMIOS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/kprobes.c
@@ -440,7 +440,7 @@
 
 	/* Replace the return addr with trampoline addr */
 	regs->u_regs[UREG_RETPC] =
-		((unsigned long)kretprobe_trampoline) - 8;
+		((unsigned long)__kretprobe_trampoline) - 8;
 }
 
 /*
@@ -451,7 +451,7 @@
 {
 	unsigned long orig_ret_address = 0;
 
-	orig_ret_address = __kretprobe_trampoline_handler(regs, &kretprobe_trampoline, NULL);
+	orig_ret_address = __kretprobe_trampoline_handler(regs, NULL);
 	regs->tpc = orig_ret_address;
 	regs->tnpc = orig_ret_address + 4;
 
@@ -465,13 +465,13 @@
 
 static void __used kretprobe_trampoline_holder(void)
 {
-	asm volatile(".global kretprobe_trampoline\n"
-		     "kretprobe_trampoline:\n"
+	asm volatile(".global __kretprobe_trampoline\n"
+		     "__kretprobe_trampoline:\n"
 		     "\tnop\n"
 		     "\tnop\n");
 }
 static struct kprobe trampoline_p = {
-	.addr = (kprobe_opcode_t *) &kretprobe_trampoline,
+	.addr = (kprobe_opcode_t *) &__kretprobe_trampoline,
 	.pre_handler = trampoline_probe_handler
 };
 
@@ -482,7 +482,7 @@
 
 int __kprobes arch_trampoline_kprobe(struct kprobe *p)
 {
-	if (p->addr == (kprobe_opcode_t *)&kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)&__kretprobe_trampoline)
 		return 1;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/leon_pci_grpci1.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/leon_pci_grpci1.c
@@ -696,7 +696,7 @@
 	return err;
 }
 
-static const struct of_device_id grpci1_of_match[] __initconst = {
+static const struct of_device_id grpci1_of_match[] = {
 	{
 	 .name = "GAISLER_PCIFBRG",
 	 },
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/leon_pci_grpci2.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/leon_pci_grpci2.c
@@ -887,7 +887,7 @@
 	return err;
 }
 
-static const struct of_device_id grpci2_of_match[] __initconst = {
+static const struct of_device_id grpci2_of_match[] = {
 	{
 	 .name = "GAISLER_GRPCI2",
 	 },
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/nmi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/nmi.c
@@ -274,7 +274,7 @@
 	if (!strncmp(str, "panic", 5))
 		panic_on_timeout = 1;
 
-	return 0;
+	return 1;
 }
 __setup("nmi_watchdog=", setup_nmi_watchdog);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/prom_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/prom_64.c
@@ -483,7 +483,9 @@
 	ncpus_probed++;
 #ifdef CONFIG_SMP
 	set_cpu_present(cpuid, true);
-	set_cpu_possible(cpuid, true);
+
+	if (num_possible_cpus() < nr_cpu_ids)
+		set_cpu_possible(cpuid, true);
 #endif
 	return NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/setup_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/setup_32.c
@@ -412,3 +412,10 @@
 }
 
 subsys_initcall(topology_init);
+
+#if defined(CONFIG_SPARC32) && !defined(CONFIG_SMP)
+void __init arch_cpu_finalize_init(void)
+{
+	cpu_data(0).udelay_val = loops_per_jiffy;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/setup_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/setup_64.c
@@ -684,7 +684,6 @@
 
 	paging_init();
 	init_sparc64_elf_hwcap();
-	smp_fill_in_cpu_possible_map();
 	/*
 	 * Once the OF device tree and MDESC have been setup and nr_cpus has
 	 * been parsed, we know the list of possible cpus.  Therefore we can
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/signal32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/signal32.c
@@ -780,5 +780,6 @@
 static_assert(offsetof(compat_siginfo_t, si_pkey)	== 0x14);
 static_assert(offsetof(compat_siginfo_t, si_perf_data)	== 0x10);
 static_assert(offsetof(compat_siginfo_t, si_perf_type)	== 0x14);
+static_assert(offsetof(compat_siginfo_t, si_perf_flags)	== 0x18);
 static_assert(offsetof(compat_siginfo_t, si_band)	== 0x0c);
 static_assert(offsetof(compat_siginfo_t, si_fd)		== 0x10);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/signal_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/signal_32.c
@@ -65,7 +65,7 @@
  */
 static inline bool invalid_frame_pointer(void __user *fp, int fplen)
 {
-	if ((((unsigned long) fp) & 15) || !__access_ok((unsigned long)fp, fplen))
+	if ((((unsigned long) fp) & 15) || !access_ok(fp, fplen))
 		return true;
 
 	return false;
@@ -244,7 +244,7 @@
 		get_sigframe(ksig, regs, sigframe_size);
 
 	if (invalid_frame_pointer(sf, sigframe_size)) {
-		do_exit(SIGILL);
+		force_exit_sig(SIGILL);
 		return -EINVAL;
 	}
 
@@ -336,7 +336,7 @@
 	sf = (struct rt_signal_frame __user *)
 		get_sigframe(ksig, regs, sigframe_size);
 	if (invalid_frame_pointer(sf, sigframe_size)) {
-		do_exit(SIGILL);
+		force_exit_sig(SIGILL);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/signal_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/signal_64.c
@@ -590,5 +590,6 @@
 static_assert(offsetof(siginfo_t, si_pkey)	== 0x20);
 static_assert(offsetof(siginfo_t, si_perf_data)	== 0x18);
 static_assert(offsetof(siginfo_t, si_perf_type)	== 0x20);
+static_assert(offsetof(siginfo_t, si_perf_flags) == 0x24);
 static_assert(offsetof(siginfo_t, si_band)	== 0x10);
 static_assert(offsetof(siginfo_t, si_fd)	== 0x14);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/smp_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/smp_64.c
@@ -1210,20 +1210,6 @@
 		xcall_deliver_impl = hypervisor_xcall_deliver;
 }
 
-void __init smp_fill_in_cpu_possible_map(void)
-{
-	int possible_cpus = num_possible_cpus();
-	int i;
-
-	if (possible_cpus > nr_cpu_ids)
-		possible_cpus = nr_cpu_ids;
-
-	for (i = 0; i < possible_cpus; i++)
-		set_cpu_possible(i, true);
-	for (; i < NR_CPUS; i++)
-		set_cpu_possible(i, false);
-}
-
 void smp_fill_in_sib_core_maps(void)
 {
 	unsigned int i;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/sys32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/sys32.S
@@ -18,224 +18,3 @@
 	sethi		%hi(sys_mmap), %g1
 	jmpl		%g1 + %lo(sys_mmap), %g0
 	 sllx		%o5, 12, %o5
-
-	.align		32
-	.globl		sys32_socketcall
-sys32_socketcall:	/* %o0=call, %o1=args */
-	cmp		%o0, 1
-	bl,pn		%xcc, do_einval
-	 cmp		%o0, 18
-	bg,pn		%xcc, do_einval
-	 sub		%o0, 1, %o0
-	sllx		%o0, 5, %o0
-	sethi		%hi(__socketcall_table_begin), %g2
-	or		%g2, %lo(__socketcall_table_begin), %g2
-	jmpl		%g2 + %o0, %g0
-	 nop
-do_einval:
-	retl
-	 mov		-EINVAL, %o0
-
-	.align		32
-__socketcall_table_begin:
-
-	/* Each entry is exactly 32 bytes. */
-do_sys_socket: /* sys_socket(int, int, int) */
-1:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_socket), %g1
-2:	ldswa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(sys_socket), %g0
-3:	 ldswa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_bind: /* sys_bind(int fd, struct sockaddr *, int) */
-4:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_bind), %g1
-5:	ldswa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(sys_bind), %g0
-6:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_connect: /* sys_connect(int, struct sockaddr *, int) */
-7:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_connect), %g1
-8:	ldswa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(sys_connect), %g0
-9:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_listen: /* sys_listen(int, int) */
-10:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_listen), %g1
-	jmpl		%g1 + %lo(sys_listen), %g0
-11:	 ldswa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-	nop
-do_sys_accept: /* sys_accept(int, struct sockaddr *, int *) */
-12:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_accept), %g1
-13:	lduwa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(sys_accept), %g0
-14:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_getsockname: /* sys_getsockname(int, struct sockaddr *, int *) */
-15:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_getsockname), %g1
-16:	lduwa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(sys_getsockname), %g0
-17:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_getpeername: /* sys_getpeername(int, struct sockaddr *, int *) */
-18:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_getpeername), %g1
-19:	lduwa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(sys_getpeername), %g0
-20:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_socketpair: /* sys_socketpair(int, int, int, int *) */
-21:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_socketpair), %g1
-22:	ldswa		[%o1 + 0x8] %asi, %o2
-23:	lduwa		[%o1 + 0xc] %asi, %o3
-	jmpl		%g1 + %lo(sys_socketpair), %g0
-24:	 ldswa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-do_sys_send: /* sys_send(int, void *, size_t, unsigned int) */
-25:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_send), %g1
-26:	lduwa		[%o1 + 0x8] %asi, %o2
-27:	lduwa		[%o1 + 0xc] %asi, %o3
-	jmpl		%g1 + %lo(sys_send), %g0
-28:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-do_sys_recv: /* sys_recv(int, void *, size_t, unsigned int) */
-29:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_recv), %g1
-30:	lduwa		[%o1 + 0x8] %asi, %o2
-31:	lduwa		[%o1 + 0xc] %asi, %o3
-	jmpl		%g1 + %lo(sys_recv), %g0
-32:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-do_sys_sendto: /* sys_sendto(int, u32, compat_size_t, unsigned int, u32, int) */
-33:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_sendto), %g1
-34:	lduwa		[%o1 + 0x8] %asi, %o2
-35:	lduwa		[%o1 + 0xc] %asi, %o3
-36:	lduwa		[%o1 + 0x10] %asi, %o4
-37:	ldswa		[%o1 + 0x14] %asi, %o5
-	jmpl		%g1 + %lo(sys_sendto), %g0
-38:	 lduwa		[%o1 + 0x4] %asi, %o1
-do_sys_recvfrom: /* sys_recvfrom(int, u32, compat_size_t, unsigned int, u32, u32) */
-39:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_recvfrom), %g1
-40:	lduwa		[%o1 + 0x8] %asi, %o2
-41:	lduwa		[%o1 + 0xc] %asi, %o3
-42:	lduwa		[%o1 + 0x10] %asi, %o4
-43:	lduwa		[%o1 + 0x14] %asi, %o5
-	jmpl		%g1 + %lo(sys_recvfrom), %g0
-44:	 lduwa		[%o1 + 0x4] %asi, %o1
-do_sys_shutdown: /* sys_shutdown(int, int) */
-45:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_shutdown), %g1
-	jmpl		%g1 + %lo(sys_shutdown), %g0
-46:	 ldswa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-	nop
-do_sys_setsockopt: /* sys_setsockopt(int, int, int, char *, int) */
-47:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_setsockopt), %g1
-48:	ldswa		[%o1 + 0x8] %asi, %o2
-49:	lduwa		[%o1 + 0xc] %asi, %o3
-50:	ldswa		[%o1 + 0x10] %asi, %o4
-	jmpl		%g1 + %lo(sys_setsockopt), %g0
-51:	 ldswa		[%o1 + 0x4] %asi, %o1
-	nop
-do_sys_getsockopt: /* sys_getsockopt(int, int, int, u32, u32) */
-52:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_getsockopt), %g1
-53:	ldswa		[%o1 + 0x8] %asi, %o2
-54:	lduwa		[%o1 + 0xc] %asi, %o3
-55:	lduwa		[%o1 + 0x10] %asi, %o4
-	jmpl		%g1 + %lo(sys_getsockopt), %g0
-56:	 ldswa		[%o1 + 0x4] %asi, %o1
-	nop
-do_sys_sendmsg: /* compat_sys_sendmsg(int, struct compat_msghdr *, unsigned int) */
-57:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(compat_sys_sendmsg), %g1
-58:	lduwa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(compat_sys_sendmsg), %g0
-59:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_recvmsg: /* compat_sys_recvmsg(int, struct compat_msghdr *, unsigned int) */
-60:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(compat_sys_recvmsg), %g1
-61:	lduwa		[%o1 + 0x8] %asi, %o2
-	jmpl		%g1 + %lo(compat_sys_recvmsg), %g0
-62:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-	nop
-do_sys_accept4: /* sys_accept4(int, struct sockaddr *, int *, int) */
-63:	ldswa		[%o1 + 0x0] %asi, %o0
-	sethi		%hi(sys_accept4), %g1
-64:	lduwa		[%o1 + 0x8] %asi, %o2
-65:	ldswa		[%o1 + 0xc] %asi, %o3
-	jmpl		%g1 + %lo(sys_accept4), %g0
-66:	 lduwa		[%o1 + 0x4] %asi, %o1
-	nop
-	nop
-
-	.section	__ex_table,"a"
-	.align		4
-	.word		1b, __retl_efault, 2b, __retl_efault
-	.word		3b, __retl_efault, 4b, __retl_efault
-	.word		5b, __retl_efault, 6b, __retl_efault
-	.word		7b, __retl_efault, 8b, __retl_efault
-	.word		9b, __retl_efault, 10b, __retl_efault
-	.word		11b, __retl_efault, 12b, __retl_efault
-	.word		13b, __retl_efault, 14b, __retl_efault
-	.word		15b, __retl_efault, 16b, __retl_efault
-	.word		17b, __retl_efault, 18b, __retl_efault
-	.word		19b, __retl_efault, 20b, __retl_efault
-	.word		21b, __retl_efault, 22b, __retl_efault
-	.word		23b, __retl_efault, 24b, __retl_efault
-	.word		25b, __retl_efault, 26b, __retl_efault
-	.word		27b, __retl_efault, 28b, __retl_efault
-	.word		29b, __retl_efault, 30b, __retl_efault
-	.word		31b, __retl_efault, 32b, __retl_efault
-	.word		33b, __retl_efault, 34b, __retl_efault
-	.word		35b, __retl_efault, 36b, __retl_efault
-	.word		37b, __retl_efault, 38b, __retl_efault
-	.word		39b, __retl_efault, 40b, __retl_efault
-	.word		41b, __retl_efault, 42b, __retl_efault
-	.word		43b, __retl_efault, 44b, __retl_efault
-	.word		45b, __retl_efault, 46b, __retl_efault
-	.word		47b, __retl_efault, 48b, __retl_efault
-	.word		49b, __retl_efault, 50b, __retl_efault
-	.word		51b, __retl_efault, 52b, __retl_efault
-	.word		53b, __retl_efault, 54b, __retl_efault
-	.word		55b, __retl_efault, 56b, __retl_efault
-	.word		57b, __retl_efault, 58b, __retl_efault
-	.word		59b, __retl_efault, 60b, __retl_efault
-	.word		61b, __retl_efault, 62b, __retl_efault
-	.word		63b, __retl_efault, 64b, __retl_efault
-	.word		65b, __retl_efault, 66b, __retl_efault
-	.previous
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/syscalls/syscall.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/syscalls/syscall.tbl
@@ -117,7 +117,7 @@
 90	common	dup2			sys_dup2
 91	32	setfsuid32		sys_setfsuid
 92	common	fcntl			sys_fcntl			compat_sys_fcntl
-93	common	select			sys_select
+93	common	select			sys_select			compat_sys_select
 94	32	setfsgid32		sys_setfsgid
 95	common	fsync			sys_fsync
 96	common	setpriority		sys_setpriority
@@ -155,7 +155,7 @@
 123	32	fchown			sys_fchown16
 123	64	fchown			sys_fchown
 124	common	fchmod			sys_fchmod
-125	common	recvfrom		sys_recvfrom
+125	common	recvfrom		sys_recvfrom			compat_sys_recvfrom
 126	32	setreuid		sys_setreuid16
 126	64	setreuid		sys_setreuid
 127	32	setregid		sys_setregid16
@@ -247,7 +247,7 @@
 204	32	readdir			sys_old_readdir			compat_sys_old_readdir
 204	64	readdir			sys_nis_syscall
 205	common	readahead		sys_readahead			compat_sys_readahead
-206	common	socketcall		sys_socketcall			sys32_socketcall
+206	common	socketcall		sys_socketcall			compat_sys_socketcall
 207	common	syslog			sys_syslog
 208	common	lookup_dcookie		sys_lookup_dcookie		compat_sys_lookup_dcookie
 209	common	fadvise64		sys_fadvise64			compat_sys_fadvise64
@@ -461,7 +461,7 @@
 412	32	utimensat_time64		sys_utimensat			sys_utimensat
 413	32	pselect6_time64			sys_pselect6			compat_sys_pselect6_time64
 414	32	ppoll_time64			sys_ppoll			compat_sys_ppoll_time64
-416	32	io_pgetevents_time64		sys_io_pgetevents		sys_io_pgetevents
+416	32	io_pgetevents_time64		sys_io_pgetevents		compat_sys_io_pgetevents_time64
 417	32	recvmmsg_time64			sys_recvmmsg			compat_sys_recvmmsg_time64
 418	32	mq_timedsend_time64		sys_mq_timedsend		sys_mq_timedsend
 419	32	mq_timedreceive_time64		sys_mq_timedreceive		sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/traps_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/traps_32.c
@@ -86,9 +86,7 @@
 	}
 	printk("Instruction DUMP:");
 	instruction_dump ((unsigned long *) regs->pc);
-	if(regs->psr & PSR_PS)
-		do_exit(SIGKILL);
-	do_exit(SIGSEGV);
+	make_task_dead((regs->psr & PSR_PS) ? SIGKILL : SIGSEGV);
 }
 
 void do_hw_interrupt(struct pt_regs *regs, unsigned long type)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/traps_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/traps_64.c
@@ -2559,9 +2559,7 @@
 	}
 	if (panic_on_oops)
 		panic("Fatal exception");
-	if (regs->tstate & TSTATE_PRIV)
-		do_exit(SIGKILL);
-	do_exit(SIGSEGV);
+	make_task_dead((regs->tstate & TSTATE_PRIV)? SIGKILL : SIGSEGV);
 }
 EXPORT_SYMBOL(die_if_kernel);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/kernel/windows.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/kernel/windows.c
@@ -121,8 +121,10 @@
 
 		if ((sp & 7) ||
 		    copy_to_user((char __user *) sp, &tp->reg_window[window],
-				 sizeof(struct reg_window32)))
-			do_exit(SIGILL);
+				 sizeof(struct reg_window32))) {
+			force_exit_sig(SIGILL);
+			return;
+		}
 	}
 	tp->w_saved = 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/lib/checksum_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/lib/checksum_32.S
@@ -453,5 +453,5 @@
  * we only bother with faults on loads... */
 
 cc_fault:
-	ret
+	retl
 	 clr	%o0
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/prom/init_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/prom/init_64.c
@@ -26,9 +26,6 @@
  * routines in the prom library.
  * It gets passed the pointer to the PROM vector.
  */
-
-extern void prom_cif_init(void *);
-
 void __init prom_init(void *cif_handler)
 {
 	phandle node;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/prom/p1275.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/prom/p1275.c
@@ -49,7 +49,7 @@
 	local_irq_restore(flags);
 }
 
-void prom_cif_init(void *cif_handler, void *cif_stack)
+void prom_cif_init(void *cif_handler)
 {
 	p1275buf.prom_cif_handler = (void (*)(long *))cif_handler;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/sparc/vdso/vma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/sparc/vdso/vma.c
@@ -449,9 +449,8 @@
 	unsigned long val;
 
 	err = kstrtoul(s, 10, &val);
-	if (err)
-		return err;
-	vdso_enabled = val;
-	return 0;
+	if (!err)
+		vdso_enabled = val;
+	return 1;
 }
 __setup("vdso=", vdso_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/um/Kconfig
@@ -6,6 +6,7 @@
 	bool
 	default y
 	select ARCH_EPHEMERAL_INODES
+	select ARCH_HAS_CPU_FINALIZE_INIT
 	select ARCH_HAS_KCOV
 	select ARCH_HAS_STRNCPY_FROM_USER
 	select ARCH_HAS_STRNLEN_USER
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/um/Makefile
@@ -132,15 +132,23 @@
 # The wrappers will select whether using "malloc" or the kernel allocator.
 LINK_WRAPS = -Wl,--wrap,malloc -Wl,--wrap,free -Wl,--wrap,calloc
 
+# Avoid binutils 2.39+ warnings by marking the stack non-executable and
+# ignorning warnings for the kallsyms sections.
+LDFLAGS_EXECSTACK = -z noexecstack
+ifeq ($(CONFIG_LD_IS_BFD),y)
+LDFLAGS_EXECSTACK += $(call ld-option,--no-warn-rwx-segments)
+endif
+
 LD_FLAGS_CMDLINE = $(foreach opt,$(KBUILD_LDFLAGS),-Wl,$(opt))
 
 # Used by link-vmlinux.sh which has special support for um link
 export CFLAGS_vmlinux := $(LINK-y) $(LINK_WRAPS) $(LD_FLAGS_CMDLINE)
+export LDFLAGS_vmlinux := $(LDFLAGS_EXECSTACK)
 
 # When cleaning we don't include .config, so we don't include
 # TT or skas makefiles and don't clean skas_ptregs.h.
 CLEAN_FILES += linux x.i gmon.out
-MRPROPER_FILES += arch/$(SUBARCH)/include/generated
+MRPROPER_FILES += $(HOST_DIR)/include/generated
 
 archclean:
 	@find . \( -name '*.bb' -o -name '*.bbg' -o -name '*.da' \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/configs/i386_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/um/configs/i386_defconfig
@@ -35,6 +35,7 @@
 CONFIG_XTERM_CHAN=y
 CONFIG_CON_CHAN="pts"
 CONFIG_SSL_CHAN="pts"
+CONFIG_SOUND=m
 CONFIG_UML_SOUND=m
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/configs/x86_64_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/um/configs/x86_64_defconfig
@@ -33,6 +33,7 @@
 CONFIG_XTERM_CHAN=y
 CONFIG_CON_CHAN="pts"
 CONFIG_SSL_CHAN="pts"
+CONFIG_SOUND=m
 CONFIG_UML_SOUND=m
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/Kconfig
@@ -104,24 +104,14 @@
 
 config UML_SOUND
 	tristate "Sound support"
+	depends on SOUND
+	select SOUND_OSS_CORE
 	help
 	  This option enables UML sound support.  If enabled, it will pull in
-	  soundcore and the UML hostaudio relay, which acts as a intermediary
+	  the UML hostaudio relay, which acts as a intermediary
 	  between the host's dsp and mixer devices and the UML sound system.
 	  It is safe to say 'Y' here.
 
-config SOUND
-	tristate
-	default UML_SOUND
-
-config SOUND_OSS_CORE
-	bool
-	default UML_SOUND
-
-config HOSTAUDIO
-	tristate
-	default UML_SOUND
-
 endmenu
 
 menu "UML Network Devices"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/Makefile
@@ -16,7 +16,8 @@
 hostaudio-objs := hostaudio_kern.o
 ubd-objs := ubd_kern.o ubd_user.o
 port-objs := port_kern.o port_user.o
-harddog-objs := harddog_kern.o harddog_user.o
+harddog-objs := harddog_kern.o
+harddog-builtin-$(CONFIG_UML_WATCHDOG) := harddog_user.o harddog_user_exp.o
 rtc-objs := rtc_kern.o rtc_user.o
 
 LDFLAGS_pcap.o = $(shell $(CC) $(KBUILD_CFLAGS) -print-file-name=libpcap.a)
@@ -53,13 +54,14 @@
 obj-$(CONFIG_MCONSOLE) += mconsole.o
 obj-$(CONFIG_MMAPPER) += mmapper_kern.o 
 obj-$(CONFIG_BLK_DEV_UBD) += ubd.o 
-obj-$(CONFIG_HOSTAUDIO) += hostaudio.o
+obj-$(CONFIG_UML_SOUND) += hostaudio.o
 obj-$(CONFIG_NULL_CHAN) += null.o 
 obj-$(CONFIG_PORT_CHAN) += port.o
 obj-$(CONFIG_PTY_CHAN) += pty.o
 obj-$(CONFIG_TTY_CHAN) += tty.o 
 obj-$(CONFIG_XTERM_CHAN) += xterm.o xterm_kern.o
 obj-$(CONFIG_UML_WATCHDOG) += harddog.o
+obj-y += $(harddog-builtin-y) $(harddog-builtin-m)
 obj-$(CONFIG_BLK_DEV_COW_COMMON) += cow_user.o
 obj-$(CONFIG_UML_RANDOM) += random.o
 obj-$(CONFIG_VIRTIO_UML) += virtio_uml.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/chan_kern.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/chan_kern.c
@@ -133,7 +133,7 @@
 	struct line *line = container_of(work, struct line, task.work);
 
 	if (!line->throttled)
-		chan_interrupt(line, line->driver->read_irq);
+		chan_interrupt(line, line->read_irq);
 }
 
 int enable_chan(struct line *line)
@@ -195,9 +195,9 @@
 		chan = list_entry(ele, struct chan, free_list);
 
 		if (chan->input && chan->enabled)
-			um_free_irq(chan->line->driver->read_irq, chan);
+			um_free_irq(chan->line->read_irq, chan);
 		if (chan->output && chan->enabled)
-			um_free_irq(chan->line->driver->write_irq, chan);
+			um_free_irq(chan->line->write_irq, chan);
 		chan->enabled = 0;
 	}
 }
@@ -215,9 +215,9 @@
 		spin_unlock_irqrestore(&irqs_to_free_lock, flags);
 	} else {
 		if (chan->input && chan->enabled)
-			um_free_irq(chan->line->driver->read_irq, chan);
+			um_free_irq(chan->line->read_irq, chan);
 		if (chan->output && chan->enabled)
-			um_free_irq(chan->line->driver->write_irq, chan);
+			um_free_irq(chan->line->write_irq, chan);
 		chan->enabled = 0;
 	}
 	if (chan->ops->close != NULL)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/chan_user.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/chan_user.c
@@ -220,7 +220,7 @@
 		       unsigned long *stack_out)
 {
 	struct winch_data data;
-	int fds[2], n, err;
+	int fds[2], n, err, pid;
 	char c;
 
 	err = os_pipe(fds, 1, 1);
@@ -238,8 +238,9 @@
 	 * problem with /dev/net/tun, which if held open by this
 	 * thread, prevents the TUN/TAP device from being reused.
 	 */
-	err = run_helper_thread(winch_thread, &data, CLONE_FILES, stack_out);
-	if (err < 0) {
+	pid = run_helper_thread(winch_thread, &data, CLONE_FILES, stack_out);
+	if (pid < 0) {
+		err = pid;
 		printk(UM_KERN_ERR "fork of winch_thread failed - errno = %d\n",
 		       -err);
 		goto out_close;
@@ -263,7 +264,7 @@
 		goto out_close;
 	}
 
-	return err;
+	return pid;
 
  out_close:
 	close(fds[1]);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/harddog.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/harddog.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef UM_WATCHDOG_H
+#define UM_WATCHDOG_H
+
+int start_watchdog(int *in_fd_ret, int *out_fd_ret, char *sock);
+void stop_watchdog(int in_fd, int out_fd);
+int ping_watchdog(int fd);
+
+#endif /* UM_WATCHDOG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/harddog_kern.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/harddog_kern.c
@@ -47,6 +47,7 @@
 #include <linux/spinlock.h>
 #include <linux/uaccess.h>
 #include "mconsole.h"
+#include "harddog.h"
 
 MODULE_LICENSE("GPL");
 
@@ -60,8 +61,6 @@
  *	Allow only one person to hold it open
  */
 
-extern int start_watchdog(int *in_fd_ret, int *out_fd_ret, char *sock);
-
 static int harddog_open(struct inode *inode, struct file *file)
 {
 	int err = -EBUSY;
@@ -92,8 +91,6 @@
 	return err;
 }
 
-extern void stop_watchdog(int in_fd, int out_fd);
-
 static int harddog_release(struct inode *inode, struct file *file)
 {
 	/*
@@ -112,8 +109,6 @@
 	return 0;
 }
 
-extern int ping_watchdog(int fd);
-
 static ssize_t harddog_write(struct file *file, const char __user *data, size_t len,
 			     loff_t *ppos)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/harddog_user.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/harddog_user.c
@@ -7,6 +7,7 @@
 #include <unistd.h>
 #include <errno.h>
 #include <os.h>
+#include "harddog.h"
 
 struct dog_data {
 	int stdin_fd;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/harddog_user_exp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/harddog_user_exp.c
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/export.h>
+#include "harddog.h"
+
+#if IS_MODULE(CONFIG_UML_WATCHDOG)
+EXPORT_SYMBOL(start_watchdog);
+EXPORT_SYMBOL(stop_watchdog);
+EXPORT_SYMBOL(ping_watchdog);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/line.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/line.c
@@ -139,7 +139,7 @@
 		count = line->buffer + LINE_BUFSIZE - line->head;
 
 		n = write_chan(line->chan_out, line->head, count,
-			       line->driver->write_irq);
+			       line->write_irq);
 		if (n < 0)
 			return n;
 		if (n == count) {
@@ -156,7 +156,7 @@
 
 	count = line->tail - line->head;
 	n = write_chan(line->chan_out, line->head, count,
-		       line->driver->write_irq);
+		       line->write_irq);
 
 	if (n < 0)
 		return n;
@@ -195,7 +195,7 @@
 		ret = buffer_data(line, buf, len);
 	else {
 		n = write_chan(line->chan_out, buf, len,
-			       line->driver->write_irq);
+			       line->write_irq);
 		if (n < 0) {
 			ret = n;
 			goto out_up;
@@ -215,7 +215,7 @@
 {
 	struct line *line = tty->driver_data;
 
-	deactivate_chan(line->chan_in, line->driver->read_irq);
+	deactivate_chan(line->chan_in, line->read_irq);
 	line->throttled = 1;
 }
 
@@ -224,7 +224,7 @@
 	struct line *line = tty->driver_data;
 
 	line->throttled = 0;
-	chan_interrupt(line, line->driver->read_irq);
+	chan_interrupt(line, line->read_irq);
 }
 
 static irqreturn_t line_write_interrupt(int irq, void *data)
@@ -260,19 +260,23 @@
 	int err;
 
 	if (input) {
-		err = um_request_irq(driver->read_irq, fd, IRQ_READ,
-				     line_interrupt, IRQF_SHARED,
+		err = um_request_irq(UM_IRQ_ALLOC, fd, IRQ_READ,
+				     line_interrupt, 0,
 				     driver->read_irq_name, data);
 		if (err < 0)
 			return err;
+
+		line->read_irq = err;
 	}
 
 	if (output) {
-		err = um_request_irq(driver->write_irq, fd, IRQ_WRITE,
-				     line_write_interrupt, IRQF_SHARED,
+		err = um_request_irq(UM_IRQ_ALLOC, fd, IRQ_WRITE,
+				     line_write_interrupt, 0,
 				     driver->write_irq_name, data);
 		if (err < 0)
 			return err;
+
+		line->write_irq = err;
 	}
 
 	return 0;
@@ -379,6 +383,7 @@
 			parse_chan_pair(NULL, line, n, opts, error_out);
 			err = 0;
 		}
+		*error_out = "configured as 'none'";
 	} else {
 		char *new = kstrdup(init, GFP_KERNEL);
 		if (!new) {
@@ -402,6 +407,7 @@
 			}
 		}
 		if (err) {
+			*error_out = "failed to parse channel pair";
 			line->init_str = NULL;
 			line->valid = 0;
 			kfree(new);
@@ -669,24 +675,26 @@
 		goto cleanup;
 	}
 
-	*winch = ((struct winch) { .list  	= LIST_HEAD_INIT(winch->list),
-				   .fd  	= fd,
+	*winch = ((struct winch) { .fd  	= fd,
 				   .tty_fd 	= tty_fd,
 				   .pid  	= pid,
 				   .port 	= port,
 				   .stack	= stack });
 
+	spin_lock(&winch_handler_lock);
+	list_add(&winch->list, &winch_handlers);
+	spin_unlock(&winch_handler_lock);
+
 	if (um_request_irq(WINCH_IRQ, fd, IRQ_READ, winch_interrupt,
 			   IRQF_SHARED, "winch", winch) < 0) {
 		printk(KERN_ERR "register_winch_irq - failed to register "
 		       "IRQ\n");
+		spin_lock(&winch_handler_lock);
+		list_del(&winch->list);
+		spin_unlock(&winch_handler_lock);
 		goto out_free;
 	}
 
-	spin_lock(&winch_handler_lock);
-	list_add(&winch->list, &winch_handlers);
-	spin_unlock(&winch_handler_lock);
-
 	return;
 
  out_free:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/line.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/line.h
@@ -23,9 +23,7 @@
 	const short minor_start;
 	const short type;
 	const short subtype;
-	const int read_irq;
 	const char *read_irq_name;
-	const int write_irq;
 	const char *write_irq_name;
 	struct mc_device mc;
 	struct tty_driver *driver;
@@ -35,6 +33,8 @@
 	struct tty_port port;
 	int valid;
 
+	int read_irq, write_irq;
+
 	char *init_str;
 	struct list_head chan_list;
 	struct chan *chan_in, *chan_out;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/mconsole_kern.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/mconsole_kern.c
@@ -224,7 +224,7 @@
 
 void mconsole_stop(struct mc_request *req)
 {
-	deactivate_fd(req->originating_fd, MCONSOLE_IRQ);
+	block_signals();
 	os_set_fd_block(req->originating_fd, 1);
 	mconsole_reply(req, "stopped", 0, 0);
 	for (;;) {
@@ -247,6 +247,7 @@
 	}
 	os_set_fd_block(req->originating_fd, 0);
 	mconsole_reply(req, "", 0, 0);
+	unblock_signals();
 }
 
 static DEFINE_SPINLOCK(mc_devices_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/net_kern.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/net_kern.c
@@ -204,7 +204,7 @@
 	return 0;
 }
 
-static int uml_net_start_xmit(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t uml_net_start_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct uml_net_private *lp = netdev_priv(dev);
 	unsigned long flags;
@@ -335,7 +335,7 @@
 
 static void net_device_release(struct device *dev)
 {
-	struct uml_net *device = dev_get_drvdata(dev);
+	struct uml_net *device = container_of(dev, struct uml_net, pdev.dev);
 	struct net_device *netdev = device->dev;
 	struct uml_net_private *lp = netdev_priv(netdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/random.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/random.c
@@ -28,7 +28,7 @@
  * protects against a module being loaded twice at the same time.
  */
 static int random_fd = -1;
-static struct hwrng hwrng = { 0, };
+static struct hwrng hwrng;
 static DECLARE_COMPLETION(have_data);
 
 static int rng_dev_read(struct hwrng *rng, void *buf, size_t max, bool block)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/ssl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/ssl.c
@@ -47,9 +47,7 @@
 	.minor_start 		= 64,
 	.type 		 	= TTY_DRIVER_TYPE_SERIAL,
 	.subtype 	 	= 0,
-	.read_irq 		= SSL_IRQ,
 	.read_irq_name 		= "ssl",
-	.write_irq 		= SSL_WRITE_IRQ,
 	.write_irq_name 	= "ssl-write",
 	.mc  = {
 		.list		= LIST_HEAD_INIT(driver.mc.list),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/stdio_console.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/stdio_console.c
@@ -53,9 +53,7 @@
 	.minor_start 		= 0,
 	.type 		 	= TTY_DRIVER_TYPE_CONSOLE,
 	.subtype 	 	= SYSTEM_TYPE_CONSOLE,
-	.read_irq 		= CONSOLE_IRQ,
 	.read_irq_name 		= "console",
-	.write_irq 		= CONSOLE_WRITE_IRQ,
 	.write_irq_name 	= "console-write",
 	.mc  = {
 		.list		= LIST_HEAD_INIT(driver.mc.list),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/ubd_kern.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/ubd_kern.c
@@ -27,6 +27,7 @@
 #include <linux/blk-mq.h>
 #include <linux/ata.h>
 #include <linux/hdreg.h>
+#include <linux/major.h>
 #include <linux/cdrom.h>
 #include <linux/proc_fs.h>
 #include <linux/seq_file.h>
@@ -813,7 +814,7 @@
 
 static void ubd_device_release(struct device *dev)
 {
-	struct ubd *ubd_dev = dev_get_drvdata(dev);
+	struct ubd *ubd_dev = container_of(dev, struct ubd, pdev.dev);
 
 	blk_mq_free_tag_set(&ubd_dev->tag_set);
 	*ubd_dev = ((struct ubd) DEFAULT_UBD);
@@ -1096,7 +1097,7 @@
 
 	if (irq_req_buffer == NULL) {
 		printk(KERN_ERR "Failed to initialize ubd buffering\n");
-		return -1;
+		return -ENOMEM;
 	}
 	io_req_buffer = kmalloc_array(UBD_REQ_BUFFER_SIZE,
 				      sizeof(struct io_thread_req *),
@@ -1107,7 +1108,7 @@
 
 	if (io_req_buffer == NULL) {
 		printk(KERN_ERR "Failed to initialize ubd buffering\n");
-		return -1;
+		return -ENOMEM;
 	}
 	platform_driver_register(&ubd_driver);
 	mutex_lock(&ubd_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/vector_kern.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/vector_kern.c
@@ -141,7 +141,7 @@
 
 	if (allow != NULL) {
 		if (kstrtoul(allow, 10, &result) == 0)
-			return (allow > 0);
+			return result > 0;
 	}
 	return false;
 }
@@ -770,6 +770,7 @@
 
 	if (parsed == NULL) {
 		*error_out = "vector_config failed to parse parameters";
+		kfree(params);
 		return -EINVAL;
 	}
 
@@ -825,7 +826,8 @@
 
 static void vector_device_release(struct device *dev)
 {
-	struct vector_device *device = dev_get_drvdata(dev);
+	struct vector_device *device =
+		container_of(dev, struct vector_device, pdev.dev);
 	struct net_device *netdev = device->dev;
 
 	list_del(&device->list);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/virt-pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/virt-pci.c
@@ -131,8 +131,11 @@
 				out ? 1 : 0,
 				posted ? cmd : HANDLE_NO_FREE(cmd),
 				GFP_ATOMIC);
-	if (ret)
+	if (ret) {
+		if (posted)
+			kfree(cmd);
 		goto out;
+	}
 
 	if (posted) {
 		virtqueue_kick(dev->cmd_vq);
@@ -181,15 +184,15 @@
 	/* buf->data is maximum size - we may only use parts of it */
 	struct um_pci_message_buffer *buf;
 	u8 *data;
-	unsigned long ret = ~0ULL;
+	unsigned long ret = ULONG_MAX;
 
 	if (!dev)
-		return ~0ULL;
+		return ULONG_MAX;
 
 	buf = get_cpu_var(um_pci_msg_bufs);
 	data = buf->data;
 
-	memset(data, 0xff, sizeof(data));
+	memset(buf->data, 0xff, sizeof(buf->data));
 
 	switch (size) {
 	case 1:
@@ -304,7 +307,7 @@
 	/* buf->data is maximum size - we may only use parts of it */
 	struct um_pci_message_buffer *buf;
 	u8 *data;
-	unsigned long ret = ~0ULL;
+	unsigned long ret = ULONG_MAX;
 
 	buf = get_cpu_var(um_pci_msg_bufs);
 	data = buf->data;
@@ -615,22 +618,33 @@
 	struct um_pci_device *dev = vdev->priv;
 	int i;
 
-        /* Stop all virtqueues */
-        vdev->config->reset(vdev);
-        vdev->config->del_vqs(vdev);
-
 	device_set_wakeup_enable(&vdev->dev, false);
 
 	mutex_lock(&um_pci_mtx);
 	for (i = 0; i < MAX_DEVICES; i++) {
 		if (um_pci_devices[i].dev != dev)
 			continue;
+
 		um_pci_devices[i].dev = NULL;
 		irq_free_desc(dev->irq);
+
+		break;
 	}
 	mutex_unlock(&um_pci_mtx);
 
-	um_pci_rescan();
+	if (i < MAX_DEVICES) {
+		struct pci_dev *pci_dev;
+
+		pci_dev = pci_get_slot(bridge->bus, i);
+		if (pci_dev)
+			pci_stop_and_remove_bus_device_locked(pci_dev);
+	}
+
+	/* Stop all virtqueues */
+	virtio_reset_device(vdev);
+	dev->cmd_vq = NULL;
+	dev->irq_vq = NULL;
+	vdev->config->del_vqs(vdev);
 
 	kfree(dev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/drivers/virtio_uml.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/drivers/virtio_uml.c
@@ -21,6 +21,7 @@
  * Based on Virtio MMIO driver by Pawel Moll, copyright 2011-2014, ARM Ltd.
  */
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/virtio.h>
@@ -49,6 +50,7 @@
 struct virtio_uml_device {
 	struct virtio_device vdev;
 	struct platform_device *pdev;
+	struct virtio_uml_platform_data *pdata;
 
 	spinlock_t sock_lock;
 	int sock, req_fd, irq;
@@ -61,6 +63,7 @@
 
 	u8 config_changed_irq:1;
 	uint64_t vq_irq_vq_map;
+	int recv_rc;
 };
 
 struct virtio_uml_vq_info {
@@ -146,14 +149,6 @@
 
 	rc = vhost_user_recv_header(fd, msg);
 
-	if (rc == -ECONNRESET && vu_dev->registered) {
-		struct virtio_uml_platform_data *pdata;
-
-		pdata = vu_dev->pdev->dev.platform_data;
-
-		virtio_break_device(&vu_dev->vdev);
-		schedule_work(&pdata->conn_broken_wk);
-	}
 	if (rc)
 		return rc;
 	size = msg->header.size;
@@ -162,6 +157,22 @@
 	return full_read(fd, &msg->payload, size, false);
 }
 
+static void vhost_user_check_reset(struct virtio_uml_device *vu_dev,
+				   int rc)
+{
+	struct virtio_uml_platform_data *pdata = vu_dev->pdata;
+
+	if (rc != -ECONNRESET)
+		return;
+
+	if (!vu_dev->registered)
+		return;
+
+	vu_dev->registered = 0;
+
+	schedule_work(&pdata->conn_broken_wk);
+}
+
 static int vhost_user_recv_resp(struct virtio_uml_device *vu_dev,
 				struct vhost_user_msg *msg,
 				size_t max_payload_size)
@@ -169,8 +180,10 @@
 	int rc = vhost_user_recv(vu_dev, vu_dev->sock, msg,
 				 max_payload_size, true);
 
-	if (rc)
+	if (rc) {
+		vhost_user_check_reset(vu_dev, rc);
 		return rc;
+	}
 
 	if (msg->header.flags != (VHOST_USER_FLAG_REPLY | VHOST_USER_VERSION))
 		return -EPROTO;
@@ -367,6 +380,7 @@
 				 sizeof(msg.msg.payload) +
 				 sizeof(msg.extra_payload));
 
+	vu_dev->recv_rc = rc;
 	if (rc)
 		return IRQ_NONE;
 
@@ -410,7 +424,9 @@
 	if (!um_irq_timetravel_handler_used())
 		ret = vu_req_read_message(vu_dev, NULL);
 
-	if (vu_dev->vq_irq_vq_map) {
+	if (vu_dev->recv_rc) {
+		vhost_user_check_reset(vu_dev, vu_dev->recv_rc);
+	} else if (vu_dev->vq_irq_vq_map) {
 		struct virtqueue *vq;
 
 		virtio_device_for_each_vq((&vu_dev->vdev), vq) {
@@ -1090,6 +1106,8 @@
 			container_of(d, struct virtio_device, dev);
 	struct virtio_uml_device *vu_dev = to_virtio_uml_device(vdev);
 
+	time_travel_propagate_time();
+
 	/* might not have been opened due to not negotiating the feature */
 	if (vu_dev->req_fd >= 0) {
 		um_free_irq(vu_dev->irq, vu_dev);
@@ -1113,21 +1131,72 @@
 		 no_vq_suspend ? "dis" : "en");
 }
 
+static void vu_of_conn_broken(struct work_struct *wk)
+{
+	struct virtio_uml_platform_data *pdata;
+	struct virtio_uml_device *vu_dev;
+
+	pdata = container_of(wk, struct virtio_uml_platform_data, conn_broken_wk);
+
+	vu_dev = platform_get_drvdata(pdata->pdev);
+
+	virtio_break_device(&vu_dev->vdev);
+
+	/*
+	 * We can't remove the device from the devicetree so the only thing we
+	 * can do is warn.
+	 */
+	WARN_ON(1);
+}
+
 /* Platform device */
 
+static struct virtio_uml_platform_data *
+virtio_uml_create_pdata(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct virtio_uml_platform_data *pdata;
+	int ret;
+
+	if (!np)
+		return ERR_PTR(-EINVAL);
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return ERR_PTR(-ENOMEM);
+
+	INIT_WORK(&pdata->conn_broken_wk, vu_of_conn_broken);
+	pdata->pdev = pdev;
+
+	ret = of_property_read_string(np, "socket-path", &pdata->socket_path);
+	if (ret)
+		return ERR_PTR(ret);
+
+	ret = of_property_read_u32(np, "virtio-device-id",
+				   &pdata->virtio_device_id);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return pdata;
+}
+
 static int virtio_uml_probe(struct platform_device *pdev)
 {
 	struct virtio_uml_platform_data *pdata = pdev->dev.platform_data;
 	struct virtio_uml_device *vu_dev;
 	int rc;
 
-	if (!pdata)
-		return -EINVAL;
+	if (!pdata) {
+		pdata = virtio_uml_create_pdata(pdev);
+		if (IS_ERR(pdata))
+			return PTR_ERR(pdata);
+	}
 
 	vu_dev = kzalloc(sizeof(*vu_dev), GFP_KERNEL);
 	if (!vu_dev)
 		return -ENOMEM;
 
+	vu_dev->pdata = pdata;
 	vu_dev->vdev.dev.parent = &pdev->dev;
 	vu_dev->vdev.dev.release = virtio_uml_release_dev;
 	vu_dev->vdev.config = &virtio_uml_config_ops;
@@ -1136,6 +1205,8 @@
 	vu_dev->pdev = pdev;
 	vu_dev->req_fd = -1;
 
+	time_travel_propagate_time();
+
 	do {
 		rc = os_connect_socket(pdata->socket_path);
 	} while (rc == -EINTR);
@@ -1201,8 +1272,14 @@
 static void vu_conn_broken(struct work_struct *wk)
 {
 	struct virtio_uml_platform_data *pdata;
+	struct virtio_uml_device *vu_dev;
 
 	pdata = container_of(wk, struct virtio_uml_platform_data, conn_broken_wk);
+
+	vu_dev = platform_get_drvdata(pdata->pdev);
+
+	virtio_break_device(&vu_dev->vdev);
+
 	vu_unregister_cmdline_device(&pdata->pdev->dev, NULL);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/Kbuild
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/Kbuild
@@ -4,6 +4,7 @@
 generic-y += compat.h
 generic-y += current.h
 generic-y += device.h
+generic-y += dma-mapping.h
 generic-y += emergency-restart.h
 generic-y += exec.h
 generic-y += extable.h
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/archrandom.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/archrandom.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_UM_ARCHRANDOM_H__
+#define __ASM_UM_ARCHRANDOM_H__
+
+#include <linux/types.h>
+
+/* This is from <os.h>, but better not to #include that in a global header here. */
+ssize_t os_getrandom(void *buf, size_t len, unsigned int flags);
+
+static inline bool __must_check arch_get_random_long(unsigned long *v)
+{
+	return os_getrandom(v, sizeof(*v), 0) == sizeof(*v);
+}
+
+static inline bool __must_check arch_get_random_int(unsigned int *v)
+{
+	return os_getrandom(v, sizeof(*v), 0) == sizeof(*v);
+}
+
+static inline bool __must_check arch_get_random_seed_long(unsigned long *v)
+{
+	return false;
+}
+
+static inline bool __must_check arch_get_random_seed_int(unsigned int *v)
+{
+	return false;
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/delay.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/delay.h
@@ -14,7 +14,7 @@
 	ndelay(nsecs);
 }
 #undef ndelay
-#define ndelay um_ndelay
+#define ndelay(n) um_ndelay(n)
 
 static inline void um_udelay(unsigned long usecs)
 {
@@ -26,5 +26,5 @@
 	udelay(usecs);
 }
 #undef udelay
-#define udelay um_udelay
+#define udelay(n) um_udelay(n)
 #endif /* __UM_DELAY_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/irq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/irq.h
@@ -4,19 +4,15 @@
 
 #define TIMER_IRQ		0
 #define UMN_IRQ			1
-#define CONSOLE_IRQ		2
-#define CONSOLE_WRITE_IRQ	3
-#define UBD_IRQ			4
-#define UM_ETH_IRQ		5
-#define SSL_IRQ			6
-#define SSL_WRITE_IRQ		7
-#define ACCEPT_IRQ		8
-#define MCONSOLE_IRQ		9
-#define WINCH_IRQ		10
-#define SIGIO_WRITE_IRQ 	11
-#define TELNETD_IRQ 		12
-#define XTERM_IRQ 		13
-#define RANDOM_IRQ 		14
+#define UBD_IRQ			2
+#define UM_ETH_IRQ		3
+#define ACCEPT_IRQ		4
+#define MCONSOLE_IRQ		5
+#define WINCH_IRQ		6
+#define SIGIO_WRITE_IRQ 	7
+#define TELNETD_IRQ 		8
+#define XTERM_IRQ 		9
+#define RANDOM_IRQ 		10
 
 #ifdef CONFIG_UML_NET_VECTOR
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/irqflags.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/irqflags.h
@@ -3,7 +3,7 @@
 #define __UM_IRQFLAGS_H
 
 extern int signals_enabled;
-int set_signals(int enable);
+int um_set_signals(int enable);
 void block_signals(void);
 void unblock_signals(void);
 
@@ -16,7 +16,7 @@
 #define arch_local_irq_restore arch_local_irq_restore
 static inline void arch_local_irq_restore(unsigned long flags)
 {
-	set_signals(flags);
+	um_set_signals(flags);
 }
 
 #define arch_local_irq_enable arch_local_irq_enable
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/mmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/mmu.h
@@ -15,8 +15,6 @@
 	struct page *stub_pages[2];
 } mm_context_t;
 
-extern void __switch_mm(struct mm_id * mm_idp);
-
 /* Avoid tangled inclusion with asm/ldt.h */
 extern long init_new_ldt(struct mm_context *to_mm, struct mm_context *from_mm);
 extern void free_ldt(struct mm_context *mm);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/thread_info.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/thread_info.h
@@ -64,6 +64,7 @@
 #define TIF_RESTORE_SIGMASK	7
 #define TIF_NOTIFY_RESUME	8
 #define TIF_SECCOMP		9	/* secure computing */
+#define TIF_SINGLESTEP		10	/* single stepping userspace */
 
 #define _TIF_SYSCALL_TRACE	(1 << TIF_SYSCALL_TRACE)
 #define _TIF_SIGPENDING		(1 << TIF_SIGPENDING)
@@ -72,5 +73,6 @@
 #define _TIF_MEMDIE		(1 << TIF_MEMDIE)
 #define _TIF_SYSCALL_AUDIT	(1 << TIF_SYSCALL_AUDIT)
 #define _TIF_SECCOMP		(1 << TIF_SECCOMP)
+#define _TIF_SINGLESTEP		(1 << TIF_SINGLESTEP)
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/timex.h
@@ -2,13 +2,8 @@
 #ifndef __UM_TIMEX_H
 #define __UM_TIMEX_H
 
-typedef unsigned long cycles_t;
-
-static inline cycles_t get_cycles (void)
-{
-	return 0;
-}
-
 #define CLOCK_TICK_RATE (HZ)
 
+#include <asm-generic/timex.h>
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/asm/xor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/asm/xor.h
@@ -4,8 +4,10 @@
 
 #ifdef CONFIG_64BIT
 #undef CONFIG_X86_32
+#define TT_CPU_INF_XOR_DEFAULT (AVX_SELECT(&xor_block_sse_pf64))
 #else
 #define CONFIG_X86_32 1
+#define TT_CPU_INF_XOR_DEFAULT (AVX_SELECT(&xor_block_8regs))
 #endif
 
 #include <asm/cpufeature.h>
@@ -16,7 +18,7 @@
 #undef XOR_SELECT_TEMPLATE
 /* pick an arbitrary one - measuring isn't possible with inf-cpu */
 #define XOR_SELECT_TEMPLATE(x)	\
-	(time_travel_mode == TT_MODE_INFCPU ? &xor_block_8regs : NULL)
+	(time_travel_mode == TT_MODE_INFCPU ? TT_CPU_INF_XOR_DEFAULT : x)
 #endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/shared/kern_util.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/shared/kern_util.h
@@ -50,7 +50,7 @@
  * Are we disallowed to sleep? Used to choose between GFP_KERNEL and
  * GFP_ATOMIC.
  */
-extern int __cant_sleep(void);
+extern int __uml_cant_sleep(void);
 extern int get_current_pid(void);
 extern int copy_from_user_proc(void *to, void *from, int size);
 extern int cpu(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/shared/longjmp.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/shared/longjmp.h
@@ -18,7 +18,7 @@
 	enable = *(volatile int *)&signals_enabled;	\
 	n = setjmp(*buf);				\
 	if(n != 0)					\
-		set_signals_trace(enable);		\
+		um_set_signals_trace(enable);		\
 	n; })
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/shared/os.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/shared/os.h
@@ -11,6 +11,12 @@
 #include <irq_user.h>
 #include <longjmp.h>
 #include <mm_id.h>
+/* This is to get size_t */
+#ifndef __UM_HOST__
+#include <linux/types.h>
+#else
+#include <sys/types.h>
+#endif
 
 #define CATCH_EINTR(expr) while ((errno = 0, ((expr) < 0)) && (errno == EINTR))
 
@@ -238,8 +244,8 @@
 extern int change_sig(int signal, int on);
 extern void block_signals(void);
 extern void unblock_signals(void);
-extern int set_signals(int enable);
-extern int set_signals_trace(int enable);
+extern int um_set_signals(int enable);
+extern int um_set_signals_trace(int enable);
 extern int os_is_signal_stack(void);
 extern void deliver_alarm(void);
 extern void register_pm_wake_signal(void);
@@ -252,6 +258,7 @@
 extern int raw(int fd);
 extern void setup_machinename(char *machine_out);
 extern void setup_hostinfo(char *buf, int len);
+extern ssize_t os_getrandom(void *buf, size_t len, unsigned int flags);
 extern void os_dump_core(void) __attribute__ ((noreturn));
 extern void um_early_printk(const char *s, unsigned int n);
 extern void os_fix_helper_signals(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/shared/registers.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/shared/registers.h
@@ -16,8 +16,8 @@
 extern int save_fpx_registers(int pid, unsigned long *fp_regs);
 extern int restore_fpx_registers(int pid, unsigned long *fp_regs);
 extern int save_registers(int pid, struct uml_pt_regs *regs);
-extern int restore_registers(int pid, struct uml_pt_regs *regs);
-extern int init_registers(int pid);
+extern int restore_pid_registers(int pid, struct uml_pt_regs *regs);
+extern int init_pid_registers(int pid);
 extern void get_safe_registers(unsigned long *regs, unsigned long *fp_regs);
 extern unsigned long get_thread_reg(int reg, jmp_buf *buf);
 extern int get_fp_registers(int pid, unsigned long *regs);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/include/shared/skas/mm_id.h
+++ linux-xilinx-zynqmp-5.15.0/arch/um/include/shared/skas/mm_id.h
@@ -15,4 +15,6 @@
 	int kill;
 };
 
+void __switch_mm(struct mm_id *mm_idp);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/exec.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/exec.c
@@ -42,7 +42,7 @@
 {
 	PT_REGS_IP(regs) = eip;
 	PT_REGS_SP(regs) = esp;
-	current->ptrace &= ~PT_DTRACE;
+	clear_thread_flag(TIF_SINGLESTEP);
 #ifdef SUBARCH_EXECVE1
 	SUBARCH_EXECVE1(regs->regs);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/ksyms.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/ksyms.c
@@ -6,7 +6,7 @@
 #include <linux/module.h>
 #include <os.h>
 
-EXPORT_SYMBOL(set_signals);
+EXPORT_SYMBOL(um_set_signals);
 EXPORT_SYMBOL(signals_enabled);
 
 EXPORT_SYMBOL(os_stat_fd);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/physmem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/physmem.c
@@ -80,10 +80,10 @@
 			  unsigned long len, unsigned long long highmem)
 {
 	unsigned long reserve = reserve_end - start;
-	long map_size = len - reserve;
+	unsigned long map_size = len - reserve;
 	int err;
 
-	if(map_size <= 0) {
+	if (len <= reserve) {
 		os_warn("Too few physical memory! Needed=%lu, given=%lu\n",
 			reserve, len);
 		exit(1);
@@ -94,7 +94,7 @@
 	err = os_map_memory((void *) reserve_end, physmem_fd, reserve,
 			    map_size, 1, 1, 1);
 	if (err < 0) {
-		os_warn("setup_physmem - mapping %ld bytes of memory at 0x%p "
+		os_warn("setup_physmem - mapping %lu bytes of memory at 0x%p "
 			"failed - errno = %d\n", map_size,
 			(void *) reserve_end, err);
 		exit(1);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/process.c
@@ -218,7 +218,7 @@
 	raw_local_irq_enable();
 }
 
-int __cant_sleep(void) {
+int __uml_cant_sleep(void) {
 	return in_atomic() || irqs_disabled() || in_interrupt();
 	/* Is in_interrupt() really needed? */
 }
@@ -339,7 +339,7 @@
 {
 	struct task_struct *task = t ? t : current;
 
-	if (!(task->ptrace & PT_DTRACE))
+	if (!test_thread_flag(TIF_SINGLESTEP))
 		return 0;
 
 	if (task->thread.singlestep_syscall)
@@ -403,6 +403,6 @@
 {
 	int cpu = current_thread_info()->cpu;
 
-	return save_i387_registers(userspace_pid[cpu], (unsigned long *) fpu);
+	return save_i387_registers(userspace_pid[cpu], (unsigned long *) fpu) == 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/ptrace.c
@@ -12,7 +12,7 @@
 
 void user_enable_single_step(struct task_struct *child)
 {
-	child->ptrace |= PT_DTRACE;
+	set_tsk_thread_flag(child, TIF_SINGLESTEP);
 	child->thread.singlestep_syscall = 0;
 
 #ifdef SUBARCH_SET_SINGLESTEPPING
@@ -22,7 +22,7 @@
 
 void user_disable_single_step(struct task_struct *child)
 {
-	child->ptrace &= ~PT_DTRACE;
+	clear_tsk_thread_flag(child, TIF_SINGLESTEP);
 	child->thread.singlestep_syscall = 0;
 
 #ifdef SUBARCH_SET_SINGLESTEPPING
@@ -121,7 +121,7 @@
 }
 
 /*
- * XXX Check PT_DTRACE vs TIF_SINGLESTEP for singlestepping check and
+ * XXX Check TIF_SINGLESTEP for singlestepping check and
  * PT_PTRACED vs TIF_SYSCALL_TRACE for syscall tracing check
  */
 int syscall_trace_enter(struct pt_regs *regs)
@@ -145,7 +145,7 @@
 	audit_syscall_exit(regs);
 
 	/* Fake a debug trap */
-	if (ptraced & PT_DTRACE)
+	if (test_thread_flag(TIF_SINGLESTEP))
 		send_sigtrap(&regs->regs, 0);
 
 	if (!test_thread_flag(TIF_SYSCALL_TRACE))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/signal.c
@@ -53,7 +53,7 @@
 	unsigned long sp;
 	int err;
 
-	if ((current->ptrace & PT_DTRACE) && (current->ptrace & PT_PTRACED))
+	if (test_thread_flag(TIF_SINGLESTEP) && (current->ptrace & PT_PTRACED))
 		singlestep = 1;
 
 	/* Did we come from a system call? */
@@ -128,7 +128,7 @@
 	 * on the host.  The tracing thread will check this flag and
 	 * PTRACE_SYSCALL if necessary.
 	 */
-	if (current->ptrace & PT_DTRACE)
+	if (test_thread_flag(TIF_SINGLESTEP))
 		current->thread.singlestep_syscall =
 			is_syscall(PT_REGS_IP(&current->thread.regs));
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/sysrq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/sysrq.c
@@ -52,5 +52,5 @@
 	}
 
 	printk("%sCall Trace:\n", loglvl);
-	dump_trace(current, &stackops, (void *)loglvl);
+	dump_trace(task ?: current, &stackops, (void *)loglvl);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/time.c
@@ -432,9 +432,29 @@
 	time_travel_del_event(&ne);
 }
 
+static void time_travel_update_time_rel(unsigned long long offs)
+{
+	unsigned long flags;
+
+	/*
+	 * Disable interrupts before calculating the new time so
+	 * that a real timer interrupt (signal) can't happen at
+	 * a bad time e.g. after we read time_travel_time but
+	 * before we've completed updating the time.
+	 */
+	local_irq_save(flags);
+	time_travel_update_time(time_travel_time + offs, false);
+	local_irq_restore(flags);
+}
+
 void time_travel_ndelay(unsigned long nsec)
 {
-	time_travel_update_time(time_travel_time + nsec, false);
+	/*
+	 * Not strictly needed to use _rel() version since this is
+	 * only used in INFCPU/EXT modes, but it doesn't hurt and
+	 * is more readable too.
+	 */
+	time_travel_update_time_rel(nsec);
 }
 EXPORT_SYMBOL(time_travel_ndelay);
 
@@ -568,7 +588,11 @@
 #define time_travel_time 0
 #define time_travel_ext_waiting 0
 
-static inline void time_travel_update_time(unsigned long long ns, bool retearly)
+static inline void time_travel_update_time(unsigned long long ns, bool idle)
+{
+}
+
+static inline void time_travel_update_time_rel(unsigned long long offs)
 {
 }
 
@@ -720,9 +744,7 @@
 		 */
 		if (!irqs_disabled() && !in_interrupt() && !in_softirq() &&
 		    !time_travel_ext_waiting)
-			time_travel_update_time(time_travel_time +
-						TIMER_MULTIPLIER,
-						false);
+			time_travel_update_time_rel(TIMER_MULTIPLIER);
 		return time_travel_time / TIMER_MULTIPLIER;
 	}
 
@@ -852,9 +874,9 @@
 	return 1;
 }
 
-__setup("time-travel-start", setup_time_travel_start);
+__setup("time-travel-start=", setup_time_travel_start);
 __uml_help(setup_time_travel_start,
-"time-travel-start=<seconds>\n"
+"time-travel-start=<nanoseconds>\n"
 "Configure the UML instance's wall clock to start at this value rather than\n"
 "the host's wall clock at the time of UML boot.\n");
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/trap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/trap.c
@@ -158,7 +158,7 @@
 
 void fatal_sigsegv(void)
 {
-	force_sigsegv(SIGSEGV);
+	force_fatal_sig(SIGSEGV);
 	do_signal(&current->thread.regs);
 	/*
 	 * This is to tell gcc that we're not returning - do_signal
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/um_arch.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/um_arch.c
@@ -3,6 +3,7 @@
  * Copyright (C) 2000 - 2007 Jeff Dike (jdike@{addtoit,linux.intel}.com)
  */
 
+#include <linux/cpu.h>
 #include <linux/delay.h>
 #include <linux/init.h>
 #include <linux/mm.h>
@@ -16,6 +17,7 @@
 #include <linux/sched/task.h>
 #include <linux/kmsg_dump.h>
 #include <linux/suspend.h>
+#include <linux/random.h>
 
 #include <asm/processor.h>
 #include <asm/cpufeature.h>
@@ -30,7 +32,7 @@
 #include <os.h>
 
 #define DEFAULT_COMMAND_LINE_ROOT "root=98:0"
-#define DEFAULT_COMMAND_LINE_CONSOLE "console=tty"
+#define DEFAULT_COMMAND_LINE_CONSOLE "console=tty0"
 
 /* Changed in add_arg and setup_arch, which run before SMP is started */
 static char __initdata command_line[COMMAND_LINE_SIZE] = { 0 };
@@ -93,7 +95,7 @@
 
 static void *c_start(struct seq_file *m, loff_t *pos)
 {
-	return *pos < NR_CPUS ? cpu_data + *pos : NULL;
+	return *pos < nr_cpu_ids ? cpu_data + *pos : NULL;
 }
 
 static void *c_next(struct seq_file *m, void *v, loff_t *pos)
@@ -404,6 +406,8 @@
 
 void __init setup_arch(char **cmdline_p)
 {
+	u8 rng_seed[32];
+
 	stack_protections((unsigned long) &init_thread_info);
 	setup_physmem(uml_physmem, uml_reserved, physmem_size, highmem);
 	mem_total_pages(physmem_size, iomem_size, highmem);
@@ -413,14 +417,27 @@
 	strlcpy(boot_command_line, command_line, COMMAND_LINE_SIZE);
 	*cmdline_p = command_line;
 	setup_hostinfo(host_info, sizeof host_info);
+
+	if (os_getrandom(rng_seed, sizeof(rng_seed), 0) == sizeof(rng_seed)) {
+		add_bootloader_randomness(rng_seed, sizeof(rng_seed));
+		memzero_explicit(rng_seed, sizeof(rng_seed));
+	}
 }
 
-void __init check_bugs(void)
+void __init arch_cpu_finalize_init(void)
 {
 	arch_check_bugs();
 	os_check_bugs();
 }
 
+void apply_retpolines(s32 *start, s32 *end)
+{
+}
+
+void apply_returns(s32 *start, s32 *end)
+{
+}
+
 void apply_alternatives(struct alt_instr *start, struct alt_instr *end)
 {
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/um/kernel/vmlinux.lds.S
@@ -1,4 +1,4 @@
-
+#define RUNTIME_DISCARD_EXIT
 KERNEL_STACK_SIZE = 4096 * (1 << CONFIG_KERNEL_STACK_ORDER);
 
 #ifdef CONFIG_LD_SCRIPT_STATIC
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/helper.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/helper.c
@@ -45,7 +45,7 @@
 	unsigned long stack, sp;
 	int pid, fds[2], ret, n;
 
-	stack = alloc_stack(0, __cant_sleep());
+	stack = alloc_stack(0, __uml_cant_sleep());
 	if (stack == 0)
 		return -ENOMEM;
 
@@ -69,7 +69,7 @@
 	data.pre_data = pre_data;
 	data.argv = argv;
 	data.fd = fds[1];
-	data.buf = __cant_sleep() ? uml_kmalloc(PATH_MAX, UM_GFP_ATOMIC) :
+	data.buf = __uml_cant_sleep() ? uml_kmalloc(PATH_MAX, UM_GFP_ATOMIC) :
 					uml_kmalloc(PATH_MAX, UM_GFP_KERNEL);
 	pid = clone(helper_child, (void *) sp, CLONE_VM, &data);
 	if (pid < 0) {
@@ -116,7 +116,7 @@
 	unsigned long stack, sp;
 	int pid, status, err;
 
-	stack = alloc_stack(0, __cant_sleep());
+	stack = alloc_stack(0, __uml_cant_sleep());
 	if (stack == 0)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/registers.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/registers.c
@@ -21,7 +21,7 @@
 	return 0;
 }
 
-int restore_registers(int pid, struct uml_pt_regs *regs)
+int restore_pid_registers(int pid, struct uml_pt_regs *regs)
 {
 	int err;
 
@@ -36,7 +36,7 @@
 static unsigned long exec_regs[MAX_REG_NR];
 static unsigned long exec_fp_regs[FP_SIZE];
 
-int init_registers(int pid)
+int init_pid_registers(int pid)
 {
 	int err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/sigio.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/sigio.c
@@ -132,7 +132,7 @@
 	int n;
 	char c;
 
-	flags = set_signals_trace(0);
+	flags = um_set_signals_trace(0);
 	CATCH_EINTR(n = write(sigio_private[0], &c, sizeof(c)));
 	if (n != sizeof(c)) {
 		printk(UM_KERN_ERR "update_thread : write failed, err = %d\n",
@@ -147,7 +147,7 @@
 		goto fail;
 	}
 
-	set_signals_trace(flags);
+	um_set_signals_trace(flags);
 	return;
  fail:
 	/* Critical section start */
@@ -161,7 +161,7 @@
 	close(write_sigio_fds[0]);
 	close(write_sigio_fds[1]);
 	/* Critical section end */
-	set_signals_trace(flags);
+	um_set_signals_trace(flags);
 }
 
 int __add_sigio_fd(int fd)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/signal.c
@@ -8,6 +8,7 @@
 
 #include <stdlib.h>
 #include <stdarg.h>
+#include <stdbool.h>
 #include <errno.h>
 #include <signal.h>
 #include <string.h>
@@ -65,9 +66,7 @@
 
 int signals_enabled;
 #ifdef UML_CONFIG_UML_TIME_TRAVEL_SUPPORT
-static int signals_blocked;
-#else
-#define signals_blocked 0
+static int signals_blocked, signals_blocked_pending;
 #endif
 static unsigned int signals_pending;
 static unsigned int signals_active = 0;
@@ -76,14 +75,27 @@
 {
 	int enabled = signals_enabled;
 
-	if ((signals_blocked || !enabled) && (sig == SIGIO)) {
+#ifdef UML_CONFIG_UML_TIME_TRAVEL_SUPPORT
+	if ((signals_blocked ||
+	     __atomic_load_n(&signals_blocked_pending, __ATOMIC_SEQ_CST)) &&
+	    (sig == SIGIO)) {
+		/* increment so unblock will do another round */
+		__atomic_add_fetch(&signals_blocked_pending, 1,
+				   __ATOMIC_SEQ_CST);
+		return;
+	}
+#endif
+
+	if (!enabled && (sig == SIGIO)) {
 		/*
 		 * In TT_MODE_EXTERNAL, need to still call time-travel
-		 * handlers unless signals are also blocked for the
-		 * external time message processing. This will mark
-		 * signals_pending by itself (only if necessary.)
+		 * handlers. This will mark signals_pending by itself
+		 * (only if necessary.)
+		 * Note we won't get here if signals are hard-blocked
+		 * (which is handled above), in that case the hard-
+		 * unblock will handle things.
 		 */
-		if (!signals_blocked && time_travel_mode == TT_MODE_EXTERNAL)
+		if (time_travel_mode == TT_MODE_EXTERNAL)
 			sigio_run_timetravel_handlers();
 		else
 			signals_pending |= SIGIO_MASK;
@@ -94,7 +106,7 @@
 
 	sig_handler_common(sig, si, mc);
 
-	set_signals_trace(enabled);
+	um_set_signals_trace(enabled);
 }
 
 static void timer_real_alarm_handler(mcontext_t *mc)
@@ -126,7 +138,7 @@
 
 	signals_active &= ~SIGALRM_MASK;
 
-	set_signals_trace(enabled);
+	um_set_signals_trace(enabled);
 }
 
 void deliver_alarm(void) {
@@ -348,7 +360,7 @@
 	}
 }
 
-int set_signals(int enable)
+int um_set_signals(int enable)
 {
 	int ret;
 	if (signals_enabled == enable)
@@ -362,7 +374,7 @@
 	return ret;
 }
 
-int set_signals_trace(int enable)
+int um_set_signals_trace(int enable)
 {
 	int ret;
 	if (signals_enabled == enable)
@@ -380,33 +392,99 @@
 #ifdef UML_CONFIG_UML_TIME_TRAVEL_SUPPORT
 void mark_sigio_pending(void)
 {
+	/*
+	 * It would seem that this should be atomic so
+	 * it isn't a read-modify-write with a signal
+	 * that could happen in the middle, losing the
+	 * value set by the signal.
+	 *
+	 * However, this function is only called when in
+	 * time-travel=ext simulation mode, in which case
+	 * the only signal ever pending is SIGIO, which
+	 * is blocked while this can be called, and the
+	 * timer signal (SIGALRM) cannot happen.
+	 */
 	signals_pending |= SIGIO_MASK;
 }
 
 void block_signals_hard(void)
 {
-	if (signals_blocked)
-		return;
-	signals_blocked = 1;
+	signals_blocked++;
 	barrier();
 }
 
 void unblock_signals_hard(void)
 {
+	static bool unblocking;
+
 	if (!signals_blocked)
+		panic("unblocking signals while not blocked");
+
+	if (--signals_blocked)
 		return;
-	/* Must be set to 0 before we check the pending bits etc. */
-	signals_blocked = 0;
+	/*
+	 * Must be set to 0 before we check pending so the
+	 * SIGIO handler will run as normal unless we're still
+	 * going to process signals_blocked_pending.
+	 */
 	barrier();
 
-	if (signals_pending && signals_enabled) {
-		/* this is a bit inefficient, but that's not really important */
-		block_signals();
-		unblock_signals();
-	} else if (signals_pending & SIGIO_MASK) {
-		/* we need to run time-travel handlers even if not enabled */
-		sigio_run_timetravel_handlers();
+	/*
+	 * Note that block_signals_hard()/unblock_signals_hard() can be called
+	 * within the unblock_signals()/sigio_run_timetravel_handlers() below.
+	 * This would still be prone to race conditions since it's actually a
+	 * call _within_ e.g. vu_req_read_message(), where we observed this
+	 * issue, which loops. Thus, if the inner call handles the recorded
+	 * pending signals, we can get out of the inner call with the real
+	 * signal hander no longer blocked, and still have a race. Thus don't
+	 * handle unblocking in the inner call, if it happens, but only in
+	 * the outermost call - 'unblocking' serves as an ownership for the
+	 * signals_blocked_pending decrement.
+	 */
+	if (unblocking)
+		return;
+	unblocking = true;
+
+	while (__atomic_load_n(&signals_blocked_pending, __ATOMIC_SEQ_CST)) {
+		if (signals_enabled) {
+			/* signals are enabled so we can touch this */
+			signals_pending |= SIGIO_MASK;
+			/*
+			 * this is a bit inefficient, but that's
+			 * not really important
+			 */
+			block_signals();
+			unblock_signals();
+		} else {
+			/*
+			 * we need to run time-travel handlers even
+			 * if not enabled
+			 */
+			sigio_run_timetravel_handlers();
+		}
+
+		/*
+		 * The decrement of signals_blocked_pending must be atomic so
+		 * that the signal handler will either happen before or after
+		 * the decrement, not during a read-modify-write:
+		 *  - If it happens before, it can increment it and we'll
+		 *    decrement it and do another round in the loop.
+		 *  - If it happens after it'll see 0 for both signals_blocked
+		 *    and signals_blocked_pending and thus run the handler as
+		 *    usual (subject to signals_enabled, but that's unrelated.)
+		 *
+		 * Note that a call to unblock_signals_hard() within the calls
+		 * to unblock_signals() or sigio_run_timetravel_handlers() above
+		 * will do nothing due to the 'unblocking' state, so this cannot
+		 * underflow as the only one decrementing will be the outermost
+		 * one.
+		 */
+		if (__atomic_sub_fetch(&signals_blocked_pending, 1,
+				       __ATOMIC_SEQ_CST) < 0)
+			panic("signals_blocked_pending underflow");
 	}
+
+	unblocking = false;
 }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/skas/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/skas/process.c
@@ -5,6 +5,7 @@
  */
 
 #include <stdlib.h>
+#include <stdbool.h>
 #include <unistd.h>
 #include <sched.h>
 #include <errno.h>
@@ -707,10 +708,24 @@
 	UML_LONGJMP(&initial_jmpbuf, INIT_JMP_HALT);
 }
 
+static bool noreboot;
+
+static int __init noreboot_cmd_param(char *str, int *add)
+{
+	noreboot = true;
+	return 0;
+}
+
+__uml_setup("noreboot", noreboot_cmd_param,
+"noreboot\n"
+"    Rather than rebooting, exit always, akin to QEMU's -no-reboot option.\n"
+"    This is useful if you're using CONFIG_PANIC_TIMEOUT in order to catch\n"
+"    crashes in CI\n");
+
 void reboot_skas(void)
 {
 	block_signals_trace();
-	UML_LONGJMP(&initial_jmpbuf, INIT_JMP_REBOOT);
+	UML_LONGJMP(&initial_jmpbuf, noreboot ? INIT_JMP_HALT : INIT_JMP_REBOOT);
 }
 
 void __switch_mm(struct mm_id *mm_idp)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/start_up.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/start_up.c
@@ -368,7 +368,7 @@
 	check_tmpexec();
 
 	pid = start_ptraced_child();
-	if (init_registers(pid))
+	if (init_pid_registers(pid))
 		fatal("Failed to initialize default registers");
 	stop_ptraced_child(pid, 1, 1);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/um/os-Linux/util.c
+++ linux-xilinx-zynqmp-5.15.0/arch/um/os-Linux/util.c
@@ -14,6 +14,7 @@
 #include <sys/wait.h>
 #include <sys/mman.h>
 #include <sys/utsname.h>
+#include <sys/random.h>
 #include <init.h>
 #include <os.h>
 
@@ -96,6 +97,11 @@
 			exit(127);
 }
 
+ssize_t os_getrandom(void *buf, size_t len, unsigned int flags)
+{
+	return getrandom(buf, len, flags);
+}
+
 /*
  * UML helper threads must not handle SIGWINCH/INT/TERM
  */
@@ -167,23 +173,38 @@
 "quiet\n"
 "    Turns off information messages during boot.\n\n");
 
+/*
+ * The os_info/os_warn functions will be called by helper threads. These
+ * have a very limited stack size and using the libc formatting functions
+ * may overflow the stack.
+ * So pull in the kernel vscnprintf and use that instead with a fixed
+ * on-stack buffer.
+ */
+int vscnprintf(char *buf, size_t size, const char *fmt, va_list args);
+
 void os_info(const char *fmt, ...)
 {
+	char buf[256];
 	va_list list;
+	int len;
 
 	if (quiet_info)
 		return;
 
 	va_start(list, fmt);
-	vfprintf(stderr, fmt, list);
+	len = vscnprintf(buf, sizeof(buf), fmt, list);
+	fwrite(buf, len, 1, stderr);
 	va_end(list);
 }
 
 void os_warn(const char *fmt, ...)
 {
+	char buf[256];
 	va_list list;
+	int len;
 
 	va_start(list, fmt);
-	vfprintf(stderr, fmt, list);
+	len = vscnprintf(buf, sizeof(buf), fmt, list);
+	fwrite(buf, len, 1, stderr);
 	va_end(list);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/Kconfig
@@ -61,6 +61,7 @@
 	select ACPI_SYSTEM_POWER_STATES_SUPPORT	if ACPI
 	select ARCH_32BIT_OFF_T			if X86_32
 	select ARCH_CLOCKSOURCE_INIT
+	select ARCH_CONFIGURES_CPU_MITIGATIONS
 	select ARCH_ENABLE_HUGEPAGE_MIGRATION if X86_64 && HUGETLB_PAGE && MIGRATION
 	select ARCH_ENABLE_MEMORY_HOTPLUG if X86_64 || (X86_32 && HIGHMEM)
 	select ARCH_ENABLE_MEMORY_HOTREMOVE if MEMORY_HOTPLUG
@@ -68,6 +69,7 @@
 	select ARCH_ENABLE_THP_MIGRATION if X86_64 && TRANSPARENT_HUGEPAGE
 	select ARCH_HAS_ACPI_TABLE_UPGRADE	if ACPI
 	select ARCH_HAS_CACHE_LINE_SIZE
+	select ARCH_HAS_CPU_FINALIZE_INIT
 	select ARCH_HAS_DEBUG_VIRTUAL
 	select ARCH_HAS_DEBUG_VM_PGTABLE	if !X86_PAE
 	select ARCH_HAS_DEVMEM_IS_ALLOWED
@@ -125,6 +127,7 @@
 	select CLOCKSOURCE_VALIDATE_LAST_CYCLE
 	select CLOCKSOURCE_WATCHDOG
 	select DCACHE_WORD_ACCESS
+	select DYNAMIC_SIGFRAME
 	select EDAC_ATOMIC_SCRUB
 	select EDAC_SUPPORT
 	select GENERIC_CLOCKEVENTS_BROADCAST	if X86_64 || (X86_32 && X86_LOCAL_APIC)
@@ -192,7 +195,7 @@
 	select HAVE_DYNAMIC_FTRACE_WITH_DIRECT_CALLS
 	select HAVE_EBPF_JIT
 	select HAVE_EFFICIENT_UNALIGNED_ACCESS
-	select HAVE_EISA
+	select HAVE_EISA			if X86_32
 	select HAVE_EXIT_THREAD
 	select HAVE_FAST_GUP
 	select HAVE_FENTRY			if X86_64 || DYNAMIC_FTRACE
@@ -260,11 +263,14 @@
 	select SYSCTL_EXCEPTION_TRACE
 	select THREAD_INFO_IN_TASK
 	select TRACE_IRQFLAGS_SUPPORT
+	select TRACE_IRQFLAGS_NMI_SUPPORT
 	select USER_STACKTRACE_SUPPORT
 	select VIRT_TO_BUS
 	select HAVE_ARCH_KCSAN			if X86_64
 	select X86_FEATURE_NAMES		if PROC_FS
 	select PROC_PID_ARCH_STATUS		if PROC_FS
+	select FUNCTION_ALIGNMENT_16B		if X86_64 || X86_ALIGNMENT_16
+	select FUNCTION_ALIGNMENT_4B
 	imply IMA_SECURE_AND_OR_TRUSTED_BOOT    if EFI
 
 config INSTRUCTION_DECODER
@@ -459,15 +465,6 @@
 	def_bool y
 	depends on X86_GOLDFISH
 
-config RETPOLINE
-	bool "Avoid speculative indirect branches in kernel"
-	default y
-	help
-	  Compile kernel with the retpoline compiler options to guard against
-	  kernel-to-user data leaks by avoiding speculative indirect
-	  branches. Requires a compiler with -mindirect-branch=thunk-extern
-	  support for full protection. The kernel may run slower.
-
 config X86_CPU_RESCTRL
 	bool "x86 CPU resource control support"
 	depends on X86 && (CPU_SUP_INTEL || CPU_SUP_AMD)
@@ -1256,7 +1253,8 @@
 
 config I8K
 	tristate "Dell i8k legacy laptop support"
-	select HWMON
+	depends on HWMON
+	depends on PROC_FS
 	select SENSORS_DELL_SMM
 	help
 	  This option enables legacy /proc/i8k userspace interface in hwmon
@@ -1310,7 +1308,7 @@
 
 config MICROCODE_INTEL
 	bool "Intel microcode loading support"
-	depends on MICROCODE
+	depends on CPU_SUP_INTEL && MICROCODE
 	default MICROCODE
 	help
 	  This options enables microcode patch loading support for Intel
@@ -1322,22 +1320,21 @@
 
 config MICROCODE_AMD
 	bool "AMD microcode loading support"
-	depends on MICROCODE
+	depends on CPU_SUP_AMD && MICROCODE
 	help
 	  If you select this option, microcode patch loading support for AMD
 	  processors will be enabled.
 
-config MICROCODE_OLD_INTERFACE
-	bool "Ancient loading interface (DEPRECATED)"
+config MICROCODE_LATE_LOADING
+	bool "Late microcode loading (DANGEROUS)"
 	default n
 	depends on MICROCODE
 	help
-	  DO NOT USE THIS! This is the ancient /dev/cpu/microcode interface
-	  which was used by userspace tools like iucode_tool and microcode.ctl.
-	  It is inadequate because it runs too late to be able to properly
-	  load microcode on a machine and it needs special tools. Instead, you
-	  should've switched to the early loading method with the initrd or
-	  builtin microcode by now: Documentation/x86/microcode.rst
+	  Loading microcode late, when the system is up and executing instructions
+	  is a tricky business and should be avoided if possible. Just the sequence
+	  of synchronizing all cores and SMT threads is one fragile dance which does
+	  not guarantee that cores might not softlock after the loading. Therefore,
+	  use this at your own risk. Late loading taints the kernel too.
 
 config X86_MSR
 	tristate "/dev/cpu/*/msr - Model-specific register support"
@@ -1518,6 +1515,7 @@
 	select ARCH_HAS_FORCE_DMA_UNENCRYPTED
 	select INSTRUCTION_DECODER
 	select ARCH_HAS_RESTRICTED_VIRTIO_MEMORY_ACCESS
+	select ARCH_HAS_CC_PLATFORM
 	help
 	  Say yes to enable support for the encryption of system memory.
 	  This requires an AMD processor that supports Secure Memory
@@ -1917,6 +1915,7 @@
 	depends on ACPI
 	select UCS2_STRING
 	select EFI_RUNTIME_WRAPPERS
+	select ARCH_USE_MEMREMAP_PROT
 	help
 	  This enables the kernel to use EFI runtime services that are
 	  available (such as the EFI variable services).
@@ -1931,7 +1930,6 @@
 config EFI_STUB
 	bool "EFI stub support"
 	depends on EFI && !X86_USE_3DNOW
-	depends on $(cc-option,-mabi=ms) || X86_32
 	select RELOCATABLE
 	help
 	  This kernel feature allows a bzImage to be loaded directly
@@ -2388,10 +2386,156 @@
 
 	  Saying 'N' here may make sense for embedded or server kernels.
 
+config STRICT_SIGALTSTACK_SIZE
+	bool "Enforce strict size checking for sigaltstack"
+	depends on DYNAMIC_SIGFRAME
+	help
+	  For historical reasons MINSIGSTKSZ is a constant which became
+	  already too small with AVX512 support. Add a mechanism to
+	  enforce strict checking of the sigaltstack size against the
+	  real size of the FPU frame. This option enables the check
+	  by default. It can also be controlled via the kernel command
+	  line option 'strict_sas_size' independent of this config
+	  switch. Enabling it might break existing applications which
+	  allocate a too small sigaltstack but 'work' because they
+	  never get a signal delivered.
+
+	  Say 'N' unless you want to really enforce this check.
+
 source "kernel/livepatch/Kconfig"
 
 endmenu
 
+config CC_HAS_SLS
+	def_bool $(cc-option,-mharden-sls=all)
+
+config CC_HAS_RETURN_THUNK
+	def_bool $(cc-option,-mfunction-return=thunk-extern)
+
+menuconfig CPU_MITIGATIONS
+	bool "Mitigations for CPU vulnerabilities"
+	default y
+	help
+	  Say Y here to enable options which enable mitigations for hardware
+	  vulnerabilities (usually related to speculative execution).
+
+	  If you say N, all mitigations will be disabled. You really
+	  should know what you are doing to say so.
+
+if CPU_MITIGATIONS
+
+config PAGE_TABLE_ISOLATION
+	bool "Remove the kernel mapping in user mode"
+	default y
+	depends on (X86_64 || X86_PAE)
+	help
+	  This feature reduces the number of hardware side channels by
+	  ensuring that the majority of kernel addresses are not mapped
+	  into userspace.
+
+	  See Documentation/x86/pti.rst for more details.
+
+config RETPOLINE
+	bool "Avoid speculative indirect branches in kernel"
+	default y
+	help
+	  Compile kernel with the retpoline compiler options to guard against
+	  kernel-to-user data leaks by avoiding speculative indirect
+	  branches. Requires a compiler with -mindirect-branch=thunk-extern
+	  support for full protection. The kernel may run slower.
+
+config RETHUNK
+	bool "Enable return-thunks"
+	depends on RETPOLINE && CC_HAS_RETURN_THUNK
+	default y if X86_64
+	help
+	  Compile the kernel with the return-thunks compiler option to guard
+	  against kernel-to-user data leaks by avoiding return speculation.
+	  Requires a compiler with -mfunction-return=thunk-extern
+	  support for full protection. The kernel may run slower.
+
+config CPU_UNRET_ENTRY
+	bool "Enable UNRET on kernel entry"
+	depends on CPU_SUP_AMD && RETHUNK && X86_64
+	default y
+	help
+	  Compile the kernel with support for the retbleed=unret mitigation.
+
+config CPU_IBPB_ENTRY
+	bool "Enable IBPB on kernel entry"
+	depends on CPU_SUP_AMD && X86_64
+	default y
+	help
+	  Compile the kernel with support for the retbleed=ibpb and
+	  spec_rstack_overflow={ibpb,ibpb-vmexit} mitigations.
+
+config CPU_IBRS_ENTRY
+	bool "Enable IBRS on kernel entry"
+	depends on CPU_SUP_INTEL && X86_64
+	default y
+	help
+	  Compile the kernel with support for the spectre_v2=ibrs mitigation.
+	  This mitigates both spectre_v2 and retbleed at great cost to
+	  performance.
+
+config CPU_SRSO
+	bool "Mitigate speculative RAS overflow on AMD"
+	depends on CPU_SUP_AMD && X86_64 && RETHUNK
+	default y
+	help
+	  Enable the SRSO mitigation needed on AMD Zen1-4 machines.
+
+config SLS
+	bool "Mitigate Straight-Line-Speculation"
+	depends on CC_HAS_SLS && X86_64
+	default n
+	help
+	  Compile the kernel with straight-line-speculation options to guard
+	  against straight line speculation. The kernel image might be slightly
+	  larger.
+
+config GDS_FORCE_MITIGATION
+	bool "Force GDS Mitigation"
+	depends on CPU_SUP_INTEL
+	default n
+	help
+	  Gather Data Sampling (GDS) is a hardware vulnerability which allows
+	  unprivileged speculative access to data which was previously stored in
+	  vector registers.
+
+	  This option is equivalent to setting gather_data_sampling=force on the
+	  command line. The microcode mitigation is used if present, otherwise
+	  AVX is disabled as a mitigation. On affected systems that are missing
+	  the microcode any userspace code that unconditionally uses AVX will
+	  break with this option set.
+
+	  Setting this option on systems not vulnerable to GDS has no effect.
+
+	  If in doubt, say N.
+
+config MITIGATION_SPECTRE_BHI
+	bool "Mitigate Spectre-BHB (Branch History Injection)"
+	depends on CPU_SUP_INTEL
+	default y
+	help
+	  Enable BHI mitigations. BHI attacks are a form of Spectre V2 attacks
+	  where the branch history buffer is poisoned to speculatively steer
+	  indirect branches.
+	  See <file:Documentation/admin-guide/hw-vuln/spectre.rst>
+
+config MITIGATION_RFDS
+	bool "RFDS Mitigation"
+	depends on CPU_SUP_INTEL
+	default y
+	help
+	  Enable mitigation for Register File Data Sampling (RFDS) by default.
+	  RFDS is a hardware vulnerability which affects Intel Atom CPUs. It
+	  allows unprivileged speculative access to stale data previously
+	  stored in floating point, vector and integer registers.
+	  See also <file:Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst>
+
+endif
+
 config ARCH_HAS_ADD_PAGES
 	def_bool y
 	depends on X86_64 && ARCH_ENABLE_MEMORY_HOTPLUG
@@ -2795,6 +2939,11 @@
 config X86_X32
 	bool "x32 ABI for 64-bit mode"
 	depends on X86_64
+	# llvm-objcopy does not convert x86_64 .note.gnu.property or
+	# compressed debug sections to x86_x32 properly:
+	# https://github.com/ClangBuiltLinux/linux/issues/514
+	# https://github.com/ClangBuiltLinux/linux/issues/1141
+	depends on $(success,$(OBJCOPY) --version | head -n1 | grep -qv llvm)
 	help
 	  Include code to run binaries for the x32 native 32-bit ABI
 	  for 64-bit processors.  An x32 process gets access to the
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/Kconfig.cpu
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/Kconfig.cpu
@@ -379,7 +379,7 @@
 config X86_MINIMUM_CPU_FAMILY
 	int
 	default "64" if X86_64
-	default "6" if X86_32 && (MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MVIAC3_2 || MVIAC7 || MEFFICEON || MATOM || MCRUSOE || MCORE2 || MK7 || MK8)
+	default "6" if X86_32 && (MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MVIAC3_2 || MVIAC7 || MEFFICEON || MATOM || MCORE2 || MK7 || MK8)
 	default "5" if X86_32 && X86_CMPXCHG64
 	default "4"
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/Kconfig.debug
@@ -1,8 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
 
-config TRACE_IRQFLAGS_NMI_SUPPORT
-	def_bool y
-
 config EARLY_PRINTK_USB
 	bool
 
@@ -252,6 +249,7 @@
 
 config UNWINDER_FRAME_POINTER
 	bool "Frame pointer unwinder"
+	select ARCH_WANT_FRAME_POINTERS
 	select FRAME_POINTER
 	help
 	  This option enables the frame pointer unwinder for unwinding kernel
@@ -275,7 +273,3 @@
 	  overhead.
 
 endchoice
-
-config FRAME_POINTER
-	depends on !UNWINDER_ORC && !UNWINDER_GUESS
-	bool
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/Makefile
@@ -24,7 +24,7 @@
 
 # How to compile the 16-bit code.  Note we always compile for -march=i386;
 # that way we can complain to the user if the CPU is insufficient.
-REALMODE_CFLAGS	:= -m16 -g -Os -DDISABLE_BRANCH_PROFILING \
+REALMODE_CFLAGS	:= -m16 -g -Os -DDISABLE_BRANCH_PROFILING -D__DISABLE_EXPORTS \
 		   -Wall -Wstrict-prototypes -march=i386 -mregparm=3 \
 		   -fno-strict-aliasing -fomit-frame-pointer -fno-pic \
 		   -mno-mmx -mno-sse $(call cc-option,-fcf-protection=none)
@@ -179,6 +179,10 @@
   endif
 endif
 
+ifdef CONFIG_SLS
+  KBUILD_CFLAGS += -mharden-sls=all
+endif
+
 KBUILD_LDFLAGS += -m elf_$(UTS_MACHINE)
 
 ifdef CONFIG_LTO_CLANG
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/Makefile
@@ -103,7 +103,7 @@
 AFLAGS_header.o += -I$(objtree)/$(obj)
 $(obj)/header.o: $(obj)/zoffset.h
 
-LDFLAGS_setup.elf	:= -m elf_i386 -T
+LDFLAGS_setup.elf	:= -m elf_i386 -z noexecstack -T
 $(obj)/setup.elf: $(src)/setup.ld $(SETUP_OBJS) FORCE
 	$(call if_changed,ld)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/bioscall.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/bioscall.S
@@ -32,7 +32,7 @@
 	movw	%dx, %si
 	movw	%sp, %di
 	movw	$11, %cx
-	rep; movsd
+	rep; movsl
 
 	/* Pop full state from the stack */
 	popal
@@ -67,7 +67,7 @@
 	jz	4f
 	movw	%sp, %si
 	movw	$11, %cx
-	rep; movsd
+	rep; movsl
 4:	addw	$44, %sp
 
 	/* Restore state and return */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/boot.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/boot.h
@@ -110,66 +110,78 @@
 
 static inline u8 rdfs8(addr_t addr)
 {
+	u8 *ptr = (u8 *)absolute_pointer(addr);
 	u8 v;
-	asm volatile("movb %%fs:%1,%0" : "=q" (v) : "m" (*(u8 *)addr));
+	asm volatile("movb %%fs:%1,%0" : "=q" (v) : "m" (*ptr));
 	return v;
 }
 static inline u16 rdfs16(addr_t addr)
 {
+	u16 *ptr = (u16 *)absolute_pointer(addr);
 	u16 v;
-	asm volatile("movw %%fs:%1,%0" : "=r" (v) : "m" (*(u16 *)addr));
+	asm volatile("movw %%fs:%1,%0" : "=r" (v) : "m" (*ptr));
 	return v;
 }
 static inline u32 rdfs32(addr_t addr)
 {
+	u32 *ptr = (u32 *)absolute_pointer(addr);
 	u32 v;
-	asm volatile("movl %%fs:%1,%0" : "=r" (v) : "m" (*(u32 *)addr));
+	asm volatile("movl %%fs:%1,%0" : "=r" (v) : "m" (*ptr));
 	return v;
 }
 
 static inline void wrfs8(u8 v, addr_t addr)
 {
-	asm volatile("movb %1,%%fs:%0" : "+m" (*(u8 *)addr) : "qi" (v));
+	u8 *ptr = (u8 *)absolute_pointer(addr);
+	asm volatile("movb %1,%%fs:%0" : "+m" (*ptr) : "qi" (v));
 }
 static inline void wrfs16(u16 v, addr_t addr)
 {
-	asm volatile("movw %1,%%fs:%0" : "+m" (*(u16 *)addr) : "ri" (v));
+	u16 *ptr = (u16 *)absolute_pointer(addr);
+	asm volatile("movw %1,%%fs:%0" : "+m" (*ptr) : "ri" (v));
 }
 static inline void wrfs32(u32 v, addr_t addr)
 {
-	asm volatile("movl %1,%%fs:%0" : "+m" (*(u32 *)addr) : "ri" (v));
+	u32 *ptr = (u32 *)absolute_pointer(addr);
+	asm volatile("movl %1,%%fs:%0" : "+m" (*ptr) : "ri" (v));
 }
 
 static inline u8 rdgs8(addr_t addr)
 {
+	u8 *ptr = (u8 *)absolute_pointer(addr);
 	u8 v;
-	asm volatile("movb %%gs:%1,%0" : "=q" (v) : "m" (*(u8 *)addr));
+	asm volatile("movb %%gs:%1,%0" : "=q" (v) : "m" (*ptr));
 	return v;
 }
 static inline u16 rdgs16(addr_t addr)
 {
+	u16 *ptr = (u16 *)absolute_pointer(addr);
 	u16 v;
-	asm volatile("movw %%gs:%1,%0" : "=r" (v) : "m" (*(u16 *)addr));
+	asm volatile("movw %%gs:%1,%0" : "=r" (v) : "m" (*ptr));
 	return v;
 }
 static inline u32 rdgs32(addr_t addr)
 {
+	u32 *ptr = (u32 *)absolute_pointer(addr);
 	u32 v;
-	asm volatile("movl %%gs:%1,%0" : "=r" (v) : "m" (*(u32 *)addr));
+	asm volatile("movl %%gs:%1,%0" : "=r" (v) : "m" (*ptr));
 	return v;
 }
 
 static inline void wrgs8(u8 v, addr_t addr)
 {
-	asm volatile("movb %1,%%gs:%0" : "+m" (*(u8 *)addr) : "qi" (v));
+	u8 *ptr = (u8 *)absolute_pointer(addr);
+	asm volatile("movb %1,%%gs:%0" : "+m" (*ptr) : "qi" (v));
 }
 static inline void wrgs16(u16 v, addr_t addr)
 {
-	asm volatile("movw %1,%%gs:%0" : "+m" (*(u16 *)addr) : "ri" (v));
+	u16 *ptr = (u16 *)absolute_pointer(addr);
+	asm volatile("movw %1,%%gs:%0" : "+m" (*ptr) : "ri" (v));
 }
 static inline void wrgs32(u32 v, addr_t addr)
 {
-	asm volatile("movl %1,%%gs:%0" : "+m" (*(u32 *)addr) : "ri" (v));
+	u32 *ptr = (u32 *)absolute_pointer(addr);
+	asm volatile("movl %1,%%gs:%0" : "+m" (*ptr) : "ri" (v));
 }
 
 /* Note: these only return true/false, not a signed return value! */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/Makefile
@@ -28,7 +28,12 @@
 targets := vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 vmlinux.bin.lzma \
 	vmlinux.bin.xz vmlinux.bin.lzo vmlinux.bin.lz4 vmlinux.bin.zst
 
-KBUILD_CFLAGS := -m$(BITS) -O2
+# CLANG_FLAGS must come before any cc-disable-warning or cc-option calls in
+# case of cross compiling, as it has the '--target=' flag, which is needed to
+# avoid errors with '-march=i386', and future flags may depend on the target to
+# be valid.
+KBUILD_CFLAGS := -m$(BITS) -O2 $(CLANG_FLAGS)
+KBUILD_CFLAGS += -std=gnu11
 KBUILD_CFLAGS += -fno-strict-aliasing -fPIE
 KBUILD_CFLAGS += -Wundef
 KBUILD_CFLAGS += -DDISABLE_BRANCH_PROFILING
@@ -47,7 +52,6 @@
 # Disable relocation relaxation in case the link is not PIE.
 KBUILD_CFLAGS += $(call as-option,-Wa$(comma)-mrelax-relocations=no)
 KBUILD_CFLAGS += -include $(srctree)/include/linux/hidden.h
-KBUILD_CFLAGS += $(CLANG_FLAGS)
 
 # sev.c indirectly inludes inat-table.h which is generated during
 # compilation and stored in $(objtree). Add the directory to the includes so
@@ -66,6 +70,10 @@
 ifdef CONFIG_LD_ORPHAN_WARN
 LDFLAGS_vmlinux += --orphan-handling=warn
 endif
+LDFLAGS_vmlinux += -z noexecstack
+ifeq ($(CONFIG_LD_IS_BFD),y)
+LDFLAGS_vmlinux += $(call ld-option,--no-warn-rwx-segments)
+endif
 LDFLAGS_vmlinux += -T
 
 hostprogs	:= mkpiggy
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/efi_thunk_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/efi_thunk_64.S
@@ -93,7 +93,7 @@
 
 	pop	%rbx
 	pop	%rbp
-	ret
+	RET
 SYM_FUNC_END(__efi64_thunk)
 
 	.code32
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/head_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/head_64.S
@@ -38,6 +38,14 @@
 #include "pgtable.h"
 
 /*
+ * Fix alignment at 16 bytes. Following CONFIG_FUNCTION_ALIGNMENT will result
+ * in assembly errors due to trying to move .org backward due to the excessive
+ * alignment.
+ */
+#undef __ALIGN
+#define __ALIGN		.balign	16, 0x90
+
+/*
  * Locally defined symbols should be marked hidden:
  */
 	.hidden _bss
@@ -468,11 +476,25 @@
 	/* Save the trampoline address in RCX */
 	movq	%rax, %rcx
 
+	/* Set up 32-bit addressable stack */
+	leaq	TRAMPOLINE_32BIT_STACK_END(%rcx), %rsp
+
 	/*
-	 * Load the address of trampoline_return() into RDI.
-	 * It will be used by the trampoline to return to the main code.
+	 * Preserve live 64-bit registers on the stack: this is necessary
+	 * because the architecture does not guarantee that GPRs will retain
+	 * their full 64-bit values across a 32-bit mode switch.
+	 */
+	pushq	%rbp
+	pushq	%rbx
+	pushq	%rsi
+
+	/*
+	 * Push the 64-bit address of trampoline_return() onto the new stack.
+	 * It will be used by the trampoline to return to the main code. Due to
+	 * the 32-bit mode switch, it cannot be kept it in a register either.
 	 */
 	leaq	trampoline_return(%rip), %rdi
+	pushq	%rdi
 
 	/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
 	pushq	$__KERNEL32_CS
@@ -480,6 +502,11 @@
 	pushq	%rax
 	lretq
 trampoline_return:
+	/* Restore live 64-bit registers */
+	popq	%rsi
+	popq	%rbx
+	popq	%rbp
+
 	/* Restore the stack, the 32-bit trampoline uses its own stack */
 	leaq	rva(boot_stack_end)(%rbx), %rsp
 
@@ -600,7 +627,7 @@
 /*
  * This is the 32-bit trampoline that will be copied over to low memory.
  *
- * RDI contains the return address (might be above 4G).
+ * Return address is at the top of the stack (might be above 4G).
  * ECX contains the base address of the trampoline memory.
  * Non zero RDX means trampoline needs to enable 5-level paging.
  */
@@ -610,9 +637,6 @@
 	movl	%eax, %ds
 	movl	%eax, %ss
 
-	/* Set up new stack */
-	leal	TRAMPOLINE_32BIT_STACK_END(%ecx), %esp
-
 	/* Disable paging */
 	movl	%cr0, %eax
 	btrl	$X86_CR0_PG_BIT, %eax
@@ -672,7 +696,7 @@
 	.code64
 SYM_FUNC_START_LOCAL_NOALIGN(.Lpaging_enabled)
 	/* Return from the trampoline */
-	jmp	*%rdi
+	retq
 SYM_FUNC_END(.Lpaging_enabled)
 
 	/*
@@ -813,7 +837,7 @@
 2:	popl	%edi				// restore callee-save registers
 	popl	%ebx
 	leave
-	ret
+	RET
 SYM_FUNC_END(efi32_pe_entry)
 
 	.section ".rodata"
@@ -868,7 +892,7 @@
 
 	pop     %ecx
 	pop     %ebx
-	ret
+	RET
 SYM_FUNC_END(startup32_set_idt_entry)
 #endif
 
@@ -884,7 +908,7 @@
 	movl	%eax, rva(boot32_idt_desc+2)(%ebp)
 	lidt    rva(boot32_idt_desc)(%ebp)
 #endif
-	ret
+	RET
 SYM_FUNC_END(startup32_load_idt)
 
 /*
@@ -954,7 +978,7 @@
 	popl	%ebx
 	popl	%eax
 #endif
-	ret
+	RET
 SYM_FUNC_END(startup32_check_sev_cbit)
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/ident_map_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/ident_map_64.c
@@ -67,6 +67,14 @@
 		return NULL;
 	}
 
+	/* Consumed more tables than expected? */
+	if (pages->pgt_buf_offset == BOOT_PGT_SIZE_WARN) {
+		debug_putstr("pgt_buf running low in " __FILE__ "\n");
+		debug_putstr("Need to raise BOOT_PGT_SIZE?\n");
+		debug_putaddr(pages->pgt_buf_offset);
+		debug_putaddr(pages->pgt_buf_size);
+	}
+
 	entry = pages->pgt_buf + pages->pgt_buf_offset;
 	pages->pgt_buf_offset += PAGE_SIZE;
 
@@ -349,3 +357,8 @@
 	 */
 	add_identity_map(address, end);
 }
+
+void do_boot_nmi_trap(struct pt_regs *regs, unsigned long error_code)
+{
+	/* Empty handler to ignore NMI during early boot */
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/idt_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/idt_64.c
@@ -45,6 +45,7 @@
 	boot_idt_desc.address = (unsigned long)boot_idt;
 
 	set_idt_entry(X86_TRAP_PF, boot_page_fault);
+	set_idt_entry(X86_TRAP_NMI, boot_nmi_trap);
 
 #ifdef CONFIG_AMD_MEM_ENCRYPT
 	set_idt_entry(X86_TRAP_VC, boot_stage2_vc);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/idt_handlers_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/idt_handlers_64.S
@@ -70,6 +70,7 @@
 	.code64
 
 EXCEPTION_HANDLER	boot_page_fault do_boot_page_fault error_code=1
+EXCEPTION_HANDLER	boot_nmi_trap do_boot_nmi_trap error_code=0
 
 #ifdef CONFIG_AMD_MEM_ENCRYPT
 EXCEPTION_HANDLER	boot_stage1_vc do_vc_no_ghcb		error_code=1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/mem_encrypt.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/mem_encrypt.S
@@ -58,7 +58,7 @@
 
 #endif	/* CONFIG_AMD_MEM_ENCRYPT */
 
-	ret
+	RET
 SYM_FUNC_END(get_sev_encryption_bit)
 
 /**
@@ -92,7 +92,7 @@
 	/* All good - return success */
 	xorl	%eax, %eax
 1:
-	ret
+	RET
 2:
 	movl	$-1, %eax
 	jmp	1b
@@ -221,7 +221,7 @@
 #endif
 
 	xor	%rax, %rax
-	ret
+	RET
 SYM_FUNC_END(set_sev_encryption_mask)
 
 	.data
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/misc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/misc.h
@@ -163,6 +163,7 @@
 
 /* IDT Entry Points */
 void boot_page_fault(void);
+void boot_nmi_trap(void);
 void boot_stage1_vc(void);
 void boot_stage2_vc(void);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/compressed/sev.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/compressed/sev.c
@@ -105,6 +105,16 @@
 	return ES_OK;
 }
 
+static enum es_result vc_ioio_check(struct es_em_ctxt *ctxt, u16 port, size_t size)
+{
+	return ES_OK;
+}
+
+static bool fault_in_kernel_space(unsigned long address)
+{
+	return false;
+}
+
 #undef __init
 #undef __pa
 #define __init
@@ -182,6 +192,10 @@
 	if (result != ES_OK)
 		goto finish;
 
+	result = vc_check_opcode_bytes(&ctxt, exit_code);
+	if (result != ES_OK)
+		goto finish;
+
 	switch (exit_code) {
 	case SVM_EXIT_RDTSC:
 	case SVM_EXIT_RDTSCP:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/main.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/main.c
@@ -33,7 +33,7 @@
 		u16 cl_offset;
 	};
 	const struct old_cmdline * const oldcmd =
-		(const struct old_cmdline *)OLD_CL_ADDRESS;
+		absolute_pointer(OLD_CL_ADDRESS);
 
 	BUILD_BUG_ON(sizeof(boot_params) != 4096);
 	memcpy(&boot_params.hdr, &hdr, sizeof(hdr));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/boot/video-vga.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/boot/video-vga.c
@@ -188,7 +188,7 @@
 	vga_set_vertical_end(60*8);
 }
 
-static int vga_set_mode(struct mode_info *mode)
+static int __attribute__((optimize("no-jump-tables"))) vga_set_mode(struct mode_info *mode)
 {
 	/* Set the basic mode */
 	vga_set_basic_mode();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/configs/i386_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/configs/i386_defconfig
@@ -262,3 +262,4 @@
 CONFIG_PROVIDE_OHCI1394_DMA_INIT=y
 CONFIG_EARLY_PRINTK_DBGP=y
 CONFIG_DEBUG_BOOT_PARAMS=y
+CONFIG_KALLSYMS_ALL=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/configs/x86_64_defconfig
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/configs/x86_64_defconfig
@@ -258,3 +258,4 @@
 CONFIG_PROVIDE_OHCI1394_DMA_INIT=y
 CONFIG_EARLY_PRINTK_DBGP=y
 CONFIG_DEBUG_BOOT_PARAMS=y
+CONFIG_KALLSYMS_ALL=y
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/Makefile
@@ -61,8 +61,8 @@
 obj-$(CONFIG_CRYPTO_SHA512_SSSE3) += sha512-ssse3.o
 sha512-ssse3-y := sha512-ssse3-asm.o sha512-avx-asm.o sha512-avx2-asm.o sha512_ssse3_glue.o
 
-obj-$(CONFIG_CRYPTO_BLAKE2S_X86) += blake2s-x86_64.o
-blake2s-x86_64-y := blake2s-core.o blake2s-glue.o
+obj-$(CONFIG_CRYPTO_BLAKE2S_X86) += libblake2s-x86_64.o
+libblake2s-x86_64-y := blake2s-core.o blake2s-glue.o
 
 obj-$(CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL) += ghash-clmulni-intel.o
 ghash-clmulni-intel-y := ghash-clmulni-intel_asm.o ghash-clmulni-intel_glue.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/aegis128-aesni-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/aegis128-aesni-asm.S
@@ -20,7 +20,7 @@
 #define T1	%xmm7
 
 #define STATEP	%rdi
-#define LEN	%rsi
+#define LEN	%esi
 #define SRC	%rdx
 #define DST	%rcx
 
@@ -75,32 +75,32 @@
 	xor %r9d, %r9d
 	pxor MSG, MSG
 
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x1, %r8
 	jz .Lld_partial_1
 
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x1E, %r8
 	add SRC, %r8
 	mov (%r8), %r9b
 
 .Lld_partial_1:
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x2, %r8
 	jz .Lld_partial_2
 
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x1C, %r8
 	add SRC, %r8
 	shl $0x10, %r9
 	mov (%r8), %r9w
 
 .Lld_partial_2:
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x4, %r8
 	jz .Lld_partial_4
 
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x18, %r8
 	add SRC, %r8
 	shl $32, %r9
@@ -110,11 +110,11 @@
 .Lld_partial_4:
 	movq %r9, MSG
 
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x8, %r8
 	jz .Lld_partial_8
 
-	mov LEN, %r8
+	mov LEN, %r8d
 	and $0x10, %r8
 	add SRC, %r8
 	pslldq $8, MSG
@@ -122,7 +122,7 @@
 	pxor T0, MSG
 
 .Lld_partial_8:
-	ret
+	RET
 SYM_FUNC_END(__load_partial)
 
 /*
@@ -138,7 +138,7 @@
  *   %r10
  */
 SYM_FUNC_START_LOCAL(__store_partial)
-	mov LEN, %r8
+	mov LEN, %r8d
 	mov DST, %r9
 
 	movq T0, %r10
@@ -180,7 +180,7 @@
 	mov %r10b, (%r9)
 
 .Lst_partial_1:
-	ret
+	RET
 SYM_FUNC_END(__store_partial)
 
 /*
@@ -225,7 +225,7 @@
 	movdqu STATE4, 0x40(STATEP)
 
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_init)
 
 /*
@@ -337,7 +337,7 @@
 	movdqu STATE3, 0x30(STATEP)
 	movdqu STATE4, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lad_out_1:
 	movdqu STATE4, 0x00(STATEP)
@@ -346,7 +346,7 @@
 	movdqu STATE2, 0x30(STATEP)
 	movdqu STATE3, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lad_out_2:
 	movdqu STATE3, 0x00(STATEP)
@@ -355,7 +355,7 @@
 	movdqu STATE1, 0x30(STATEP)
 	movdqu STATE2, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lad_out_3:
 	movdqu STATE2, 0x00(STATEP)
@@ -364,7 +364,7 @@
 	movdqu STATE0, 0x30(STATEP)
 	movdqu STATE1, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lad_out_4:
 	movdqu STATE1, 0x00(STATEP)
@@ -373,11 +373,11 @@
 	movdqu STATE4, 0x30(STATEP)
 	movdqu STATE0, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lad_out:
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_ad)
 
 .macro encrypt_block a s0 s1 s2 s3 s4 i
@@ -452,7 +452,7 @@
 	movdqu STATE2, 0x30(STATEP)
 	movdqu STATE3, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lenc_out_1:
 	movdqu STATE3, 0x00(STATEP)
@@ -461,7 +461,7 @@
 	movdqu STATE1, 0x30(STATEP)
 	movdqu STATE2, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lenc_out_2:
 	movdqu STATE2, 0x00(STATEP)
@@ -470,7 +470,7 @@
 	movdqu STATE0, 0x30(STATEP)
 	movdqu STATE1, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lenc_out_3:
 	movdqu STATE1, 0x00(STATEP)
@@ -479,7 +479,7 @@
 	movdqu STATE4, 0x30(STATEP)
 	movdqu STATE0, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lenc_out_4:
 	movdqu STATE0, 0x00(STATEP)
@@ -488,11 +488,11 @@
 	movdqu STATE3, 0x30(STATEP)
 	movdqu STATE4, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Lenc_out:
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_enc)
 
 /*
@@ -532,7 +532,7 @@
 	movdqu STATE3, 0x40(STATEP)
 
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_enc_tail)
 
 .macro decrypt_block a s0 s1 s2 s3 s4 i
@@ -606,7 +606,7 @@
 	movdqu STATE2, 0x30(STATEP)
 	movdqu STATE3, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Ldec_out_1:
 	movdqu STATE3, 0x00(STATEP)
@@ -615,7 +615,7 @@
 	movdqu STATE1, 0x30(STATEP)
 	movdqu STATE2, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Ldec_out_2:
 	movdqu STATE2, 0x00(STATEP)
@@ -624,7 +624,7 @@
 	movdqu STATE0, 0x30(STATEP)
 	movdqu STATE1, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Ldec_out_3:
 	movdqu STATE1, 0x00(STATEP)
@@ -633,7 +633,7 @@
 	movdqu STATE4, 0x30(STATEP)
 	movdqu STATE0, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Ldec_out_4:
 	movdqu STATE0, 0x00(STATEP)
@@ -642,11 +642,11 @@
 	movdqu STATE3, 0x30(STATEP)
 	movdqu STATE4, 0x40(STATEP)
 	FRAME_END
-	ret
+	RET
 
 .Ldec_out:
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_dec)
 
 /*
@@ -676,7 +676,7 @@
 	call __store_partial
 
 	/* mask with byte count: */
-	movq LEN, T0
+	movd LEN, T0
 	punpcklbw T0, T0
 	punpcklbw T0, T0
 	punpcklbw T0, T0
@@ -696,12 +696,13 @@
 	movdqu STATE3, 0x40(STATEP)
 
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_dec_tail)
 
 /*
  * void crypto_aegis128_aesni_final(void *state, void *tag_xor,
- *                                  u64 assoclen, u64 cryptlen);
+ *                                  unsigned int assoclen,
+ *                                  unsigned int cryptlen);
  */
 SYM_FUNC_START(crypto_aegis128_aesni_final)
 	FRAME_BEGIN
@@ -714,8 +715,8 @@
 	movdqu 0x40(STATEP), STATE4
 
 	/* prepare length block: */
-	movq %rdx, MSG
-	movq %rcx, T0
+	movd %edx, MSG
+	movd %ecx, T0
 	pslldq $8, T0
 	pxor T0, MSG
 	psllq $3, MSG /* multiply by 8 (to get bit count) */
@@ -743,5 +744,5 @@
 	movdqu MSG, (%rsi)
 
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(crypto_aegis128_aesni_final)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/aes_ctrby8_avx-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/aes_ctrby8_avx-x86_64.S
@@ -525,7 +525,7 @@
 	/* return updated IV */
 	vpshufb	xbyteswap, xcounter, xcounter
 	vmovdqu	xcounter, (p_iv)
-	ret
+	RET
 .endm
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/aesni-intel_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/aesni-intel_asm.S
@@ -1594,7 +1594,7 @@
 	GCM_ENC_DEC dec
 	GCM_COMPLETE arg10, arg11
 	FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_dec)
 
 
@@ -1683,7 +1683,7 @@
 
 	GCM_COMPLETE arg10, arg11
 	FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_enc)
 
 /*****************************************************************************
@@ -1701,7 +1701,7 @@
 	FUNC_SAVE
 	GCM_INIT %arg3, %arg4,%arg5, %arg6
 	FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_init)
 
 /*****************************************************************************
@@ -1716,7 +1716,7 @@
 	FUNC_SAVE
 	GCM_ENC_DEC enc
 	FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_enc_update)
 
 /*****************************************************************************
@@ -1731,7 +1731,7 @@
 	FUNC_SAVE
 	GCM_ENC_DEC dec
 	FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_dec_update)
 
 /*****************************************************************************
@@ -1746,7 +1746,7 @@
 	FUNC_SAVE
 	GCM_COMPLETE %arg3 %arg4
 	FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_finalize)
 
 #endif
@@ -1762,7 +1762,7 @@
 	pxor %xmm1, %xmm0
 	movaps %xmm0, (TKEYP)
 	add $0x10, TKEYP
-	ret
+	RET
 SYM_FUNC_END(_key_expansion_256a)
 SYM_FUNC_END_ALIAS(_key_expansion_128)
 
@@ -1787,7 +1787,7 @@
 	shufps $0b01001110, %xmm2, %xmm1
 	movaps %xmm1, 0x10(TKEYP)
 	add $0x20, TKEYP
-	ret
+	RET
 SYM_FUNC_END(_key_expansion_192a)
 
 SYM_FUNC_START_LOCAL(_key_expansion_192b)
@@ -1806,7 +1806,7 @@
 
 	movaps %xmm0, (TKEYP)
 	add $0x10, TKEYP
-	ret
+	RET
 SYM_FUNC_END(_key_expansion_192b)
 
 SYM_FUNC_START_LOCAL(_key_expansion_256b)
@@ -1818,7 +1818,7 @@
 	pxor %xmm1, %xmm2
 	movaps %xmm2, (TKEYP)
 	add $0x10, TKEYP
-	ret
+	RET
 SYM_FUNC_END(_key_expansion_256b)
 
 /*
@@ -1933,7 +1933,7 @@
 	popl KEYP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_set_key)
 
 /*
@@ -1957,7 +1957,7 @@
 	popl KEYP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_enc)
 
 /*
@@ -2014,7 +2014,7 @@
 	aesenc KEY, STATE
 	movaps 0x70(TKEYP), KEY
 	aesenclast KEY, STATE
-	ret
+	RET
 SYM_FUNC_END(_aesni_enc1)
 
 /*
@@ -2122,7 +2122,7 @@
 	aesenclast KEY, STATE2
 	aesenclast KEY, STATE3
 	aesenclast KEY, STATE4
-	ret
+	RET
 SYM_FUNC_END(_aesni_enc4)
 
 /*
@@ -2147,7 +2147,7 @@
 	popl KEYP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_dec)
 
 /*
@@ -2204,7 +2204,7 @@
 	aesdec KEY, STATE
 	movaps 0x70(TKEYP), KEY
 	aesdeclast KEY, STATE
-	ret
+	RET
 SYM_FUNC_END(_aesni_dec1)
 
 /*
@@ -2312,7 +2312,7 @@
 	aesdeclast KEY, STATE2
 	aesdeclast KEY, STATE3
 	aesdeclast KEY, STATE4
-	ret
+	RET
 SYM_FUNC_END(_aesni_dec4)
 
 /*
@@ -2372,7 +2372,7 @@
 	popl LEN
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_ecb_enc)
 
 /*
@@ -2433,7 +2433,7 @@
 	popl LEN
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_ecb_dec)
 
 /*
@@ -2477,7 +2477,7 @@
 	popl IVP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_cbc_enc)
 
 /*
@@ -2570,7 +2570,7 @@
 	popl IVP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_cbc_dec)
 
 /*
@@ -2627,7 +2627,7 @@
 	popl IVP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_cts_cbc_enc)
 
 /*
@@ -2688,7 +2688,7 @@
 	popl IVP
 #endif
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_cts_cbc_dec)
 
 .pushsection .rodata
@@ -2725,7 +2725,7 @@
 	mov $1, TCTR_LOW
 	movq TCTR_LOW, INC
 	movq CTR, TCTR_LOW
-	ret
+	RET
 SYM_FUNC_END(_aesni_inc_init)
 
 /*
@@ -2753,7 +2753,7 @@
 .Linc_low:
 	movaps CTR, IV
 	pshufb BSWAP_MASK, IV
-	ret
+	RET
 SYM_FUNC_END(_aesni_inc)
 
 /*
@@ -2816,7 +2816,7 @@
 	movups IV, (IVP)
 .Lctr_enc_just_ret:
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(aesni_ctr_enc)
 
 #endif
@@ -2932,7 +2932,7 @@
 	popl IVP
 #endif
 	FRAME_END
-	ret
+	RET
 
 .Lxts_enc_1x:
 	add $64, LEN
@@ -3092,7 +3092,7 @@
 	popl IVP
 #endif
 	FRAME_END
-	ret
+	RET
 
 .Lxts_dec_1x:
 	add $64, LEN
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/aesni-intel_avx-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/aesni-intel_avx-x86_64.S
@@ -1767,7 +1767,7 @@
         FUNC_SAVE
         INIT GHASH_MUL_AVX, PRECOMPUTE_AVX
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_init_avx_gen2)
 
 ###############################################################################
@@ -1788,15 +1788,15 @@
         # must be 192
         GCM_ENC_DEC INITIAL_BLOCKS_AVX, GHASH_8_ENCRYPT_8_PARALLEL_AVX, GHASH_LAST_8_AVX, GHASH_MUL_AVX, ENC, 11
         FUNC_RESTORE
-        ret
+        RET
 key_128_enc_update:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX, GHASH_8_ENCRYPT_8_PARALLEL_AVX, GHASH_LAST_8_AVX, GHASH_MUL_AVX, ENC, 9
         FUNC_RESTORE
-        ret
+        RET
 key_256_enc_update:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX, GHASH_8_ENCRYPT_8_PARALLEL_AVX, GHASH_LAST_8_AVX, GHASH_MUL_AVX, ENC, 13
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_enc_update_avx_gen2)
 
 ###############################################################################
@@ -1817,15 +1817,15 @@
         # must be 192
         GCM_ENC_DEC INITIAL_BLOCKS_AVX, GHASH_8_ENCRYPT_8_PARALLEL_AVX, GHASH_LAST_8_AVX, GHASH_MUL_AVX, DEC, 11
         FUNC_RESTORE
-        ret
+        RET
 key_128_dec_update:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX, GHASH_8_ENCRYPT_8_PARALLEL_AVX, GHASH_LAST_8_AVX, GHASH_MUL_AVX, DEC, 9
         FUNC_RESTORE
-        ret
+        RET
 key_256_dec_update:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX, GHASH_8_ENCRYPT_8_PARALLEL_AVX, GHASH_LAST_8_AVX, GHASH_MUL_AVX, DEC, 13
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_dec_update_avx_gen2)
 
 ###############################################################################
@@ -1846,15 +1846,15 @@
         # must be 192
         GCM_COMPLETE GHASH_MUL_AVX, 11, arg3, arg4
         FUNC_RESTORE
-        ret
+        RET
 key_128_finalize:
         GCM_COMPLETE GHASH_MUL_AVX, 9, arg3, arg4
         FUNC_RESTORE
-        ret
+        RET
 key_256_finalize:
         GCM_COMPLETE GHASH_MUL_AVX, 13, arg3, arg4
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_finalize_avx_gen2)
 
 ###############################################################################
@@ -2735,7 +2735,7 @@
         FUNC_SAVE
         INIT GHASH_MUL_AVX2, PRECOMPUTE_AVX2
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_init_avx_gen4)
 
 ###############################################################################
@@ -2756,15 +2756,15 @@
         # must be 192
         GCM_ENC_DEC INITIAL_BLOCKS_AVX2, GHASH_8_ENCRYPT_8_PARALLEL_AVX2, GHASH_LAST_8_AVX2, GHASH_MUL_AVX2, ENC, 11
         FUNC_RESTORE
-	ret
+	RET
 key_128_enc_update4:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX2, GHASH_8_ENCRYPT_8_PARALLEL_AVX2, GHASH_LAST_8_AVX2, GHASH_MUL_AVX2, ENC, 9
         FUNC_RESTORE
-	ret
+	RET
 key_256_enc_update4:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX2, GHASH_8_ENCRYPT_8_PARALLEL_AVX2, GHASH_LAST_8_AVX2, GHASH_MUL_AVX2, ENC, 13
         FUNC_RESTORE
-	ret
+	RET
 SYM_FUNC_END(aesni_gcm_enc_update_avx_gen4)
 
 ###############################################################################
@@ -2785,15 +2785,15 @@
         # must be 192
         GCM_ENC_DEC INITIAL_BLOCKS_AVX2, GHASH_8_ENCRYPT_8_PARALLEL_AVX2, GHASH_LAST_8_AVX2, GHASH_MUL_AVX2, DEC, 11
         FUNC_RESTORE
-        ret
+        RET
 key_128_dec_update4:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX2, GHASH_8_ENCRYPT_8_PARALLEL_AVX2, GHASH_LAST_8_AVX2, GHASH_MUL_AVX2, DEC, 9
         FUNC_RESTORE
-        ret
+        RET
 key_256_dec_update4:
         GCM_ENC_DEC INITIAL_BLOCKS_AVX2, GHASH_8_ENCRYPT_8_PARALLEL_AVX2, GHASH_LAST_8_AVX2, GHASH_MUL_AVX2, DEC, 13
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_dec_update_avx_gen4)
 
 ###############################################################################
@@ -2814,13 +2814,13 @@
         # must be 192
         GCM_COMPLETE GHASH_MUL_AVX2, 11, arg3, arg4
         FUNC_RESTORE
-        ret
+        RET
 key_128_finalize4:
         GCM_COMPLETE GHASH_MUL_AVX2, 9, arg3, arg4
         FUNC_RESTORE
-        ret
+        RET
 key_256_finalize4:
         GCM_COMPLETE GHASH_MUL_AVX2, 13, arg3, arg4
         FUNC_RESTORE
-        ret
+        RET
 SYM_FUNC_END(aesni_gcm_finalize_avx_gen4)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/aesni-intel_glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/aesni-intel_glue.c
@@ -866,7 +866,7 @@
 		req = &subreq;
 
 		err = skcipher_walk_virt(&walk, req, false);
-		if (err)
+		if (!walk.nbytes)
 			return err;
 	} else {
 		tail = 0;
@@ -1107,7 +1107,7 @@
 		.cra_flags		= CRYPTO_ALG_INTERNAL,
 		.cra_blocksize		= 1,
 		.cra_ctxsize		= sizeof(struct aesni_rfc4106_gcm_ctx),
-		.cra_alignmask		= AESNI_ALIGN - 1,
+		.cra_alignmask		= 0,
 		.cra_module		= THIS_MODULE,
 	},
 }, {
@@ -1124,7 +1124,7 @@
 		.cra_flags		= CRYPTO_ALG_INTERNAL,
 		.cra_blocksize		= 1,
 		.cra_ctxsize		= sizeof(struct generic_gcmaes_ctx),
-		.cra_alignmask		= AESNI_ALIGN - 1,
+		.cra_alignmask		= 0,
 		.cra_module		= THIS_MODULE,
 	},
 } };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/blake2s-core.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/blake2s-core.S
@@ -171,7 +171,7 @@
 	movdqu		%xmm1,0x10(%rdi)
 	movdqu		%xmm14,0x20(%rdi)
 .Lendofloop:
-	ret
+	RET
 SYM_FUNC_END(blake2s_compress_ssse3)
 
 #ifdef CONFIG_AS_AVX512
@@ -251,6 +251,6 @@
 	vmovdqu		%xmm1,0x10(%rdi)
 	vmovdqu		%xmm4,0x20(%rdi)
 	vzeroupper
-	retq
+	RET
 SYM_FUNC_END(blake2s_compress_avx512)
 #endif /* CONFIG_AS_AVX512 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/blake2s-glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/blake2s-glue.c
@@ -4,8 +4,6 @@
  */
 
 #include <crypto/internal/blake2s.h>
-#include <crypto/internal/simd.h>
-#include <crypto/internal/hash.h>
 
 #include <linux/types.h>
 #include <linux/jump_label.h>
@@ -28,14 +26,13 @@
 static __ro_after_init DEFINE_STATIC_KEY_FALSE(blake2s_use_ssse3);
 static __ro_after_init DEFINE_STATIC_KEY_FALSE(blake2s_use_avx512);
 
-void blake2s_compress_arch(struct blake2s_state *state,
-			   const u8 *block, size_t nblocks,
-			   const u32 inc)
+void blake2s_compress(struct blake2s_state *state, const u8 *block,
+		      size_t nblocks, const u32 inc)
 {
 	/* SIMD disables preemption, so relax after processing each page. */
 	BUILD_BUG_ON(SZ_4K / BLAKE2S_BLOCK_SIZE < 8);
 
-	if (!static_branch_likely(&blake2s_use_ssse3) || !crypto_simd_usable()) {
+	if (!static_branch_likely(&blake2s_use_ssse3) || !may_use_simd()) {
 		blake2s_compress_generic(state, block, nblocks, inc);
 		return;
 	}
@@ -56,49 +53,12 @@
 		block += blocks * BLAKE2S_BLOCK_SIZE;
 	} while (nblocks);
 }
-EXPORT_SYMBOL(blake2s_compress_arch);
-
-static int crypto_blake2s_update_x86(struct shash_desc *desc,
-				     const u8 *in, unsigned int inlen)
-{
-	return crypto_blake2s_update(desc, in, inlen, blake2s_compress_arch);
-}
-
-static int crypto_blake2s_final_x86(struct shash_desc *desc, u8 *out)
-{
-	return crypto_blake2s_final(desc, out, blake2s_compress_arch);
-}
-
-#define BLAKE2S_ALG(name, driver_name, digest_size)			\
-	{								\
-		.base.cra_name		= name,				\
-		.base.cra_driver_name	= driver_name,			\
-		.base.cra_priority	= 200,				\
-		.base.cra_flags		= CRYPTO_ALG_OPTIONAL_KEY,	\
-		.base.cra_blocksize	= BLAKE2S_BLOCK_SIZE,		\
-		.base.cra_ctxsize	= sizeof(struct blake2s_tfm_ctx), \
-		.base.cra_module	= THIS_MODULE,			\
-		.digestsize		= digest_size,			\
-		.setkey			= crypto_blake2s_setkey,	\
-		.init			= crypto_blake2s_init,		\
-		.update			= crypto_blake2s_update_x86,	\
-		.final			= crypto_blake2s_final_x86,	\
-		.descsize		= sizeof(struct blake2s_state),	\
-	}
-
-static struct shash_alg blake2s_algs[] = {
-	BLAKE2S_ALG("blake2s-128", "blake2s-128-x86", BLAKE2S_128_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-160", "blake2s-160-x86", BLAKE2S_160_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-224", "blake2s-224-x86", BLAKE2S_224_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-256", "blake2s-256-x86", BLAKE2S_256_HASH_SIZE),
-};
+EXPORT_SYMBOL(blake2s_compress);
 
 static int __init blake2s_mod_init(void)
 {
-	if (!boot_cpu_has(X86_FEATURE_SSSE3))
-		return 0;
-
-	static_branch_enable(&blake2s_use_ssse3);
+	if (boot_cpu_has(X86_FEATURE_SSSE3))
+		static_branch_enable(&blake2s_use_ssse3);
 
 	if (IS_ENABLED(CONFIG_AS_AVX512) &&
 	    boot_cpu_has(X86_FEATURE_AVX) &&
@@ -109,26 +69,9 @@
 			      XFEATURE_MASK_AVX512, NULL))
 		static_branch_enable(&blake2s_use_avx512);
 
-	return IS_REACHABLE(CONFIG_CRYPTO_HASH) ?
-		crypto_register_shashes(blake2s_algs,
-					ARRAY_SIZE(blake2s_algs)) : 0;
-}
-
-static void __exit blake2s_mod_exit(void)
-{
-	if (IS_REACHABLE(CONFIG_CRYPTO_HASH) && boot_cpu_has(X86_FEATURE_SSSE3))
-		crypto_unregister_shashes(blake2s_algs, ARRAY_SIZE(blake2s_algs));
+	return 0;
 }
 
 module_init(blake2s_mod_init);
-module_exit(blake2s_mod_exit);
 
-MODULE_ALIAS_CRYPTO("blake2s-128");
-MODULE_ALIAS_CRYPTO("blake2s-128-x86");
-MODULE_ALIAS_CRYPTO("blake2s-160");
-MODULE_ALIAS_CRYPTO("blake2s-160-x86");
-MODULE_ALIAS_CRYPTO("blake2s-224");
-MODULE_ALIAS_CRYPTO("blake2s-224-x86");
-MODULE_ALIAS_CRYPTO("blake2s-256");
-MODULE_ALIAS_CRYPTO("blake2s-256-x86");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/blowfish-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/blowfish-x86_64-asm_64.S
@@ -135,10 +135,10 @@
 	jnz .L__enc_xor;
 
 	write_block();
-	ret;
+	RET;
 .L__enc_xor:
 	xor_block();
-	ret;
+	RET;
 SYM_FUNC_END(__blowfish_enc_blk)
 
 SYM_FUNC_START(blowfish_dec_blk)
@@ -170,7 +170,7 @@
 
 	movq %r11, %r12;
 
-	ret;
+	RET;
 SYM_FUNC_END(blowfish_dec_blk)
 
 /**********************************************************************
@@ -322,14 +322,14 @@
 
 	popq %rbx;
 	popq %r12;
-	ret;
+	RET;
 
 .L__enc_xor4:
 	xor_block4();
 
 	popq %rbx;
 	popq %r12;
-	ret;
+	RET;
 SYM_FUNC_END(__blowfish_enc_blk_4way)
 
 SYM_FUNC_START(blowfish_dec_blk_4way)
@@ -364,5 +364,5 @@
 	popq %rbx;
 	popq %r12;
 
-	ret;
+	RET;
 SYM_FUNC_END(blowfish_dec_blk_4way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/camellia-aesni-avx-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/camellia-aesni-avx-asm_64.S
@@ -192,7 +192,7 @@
 	roundsm16(%xmm0, %xmm1, %xmm2, %xmm3, %xmm4, %xmm5, %xmm6, %xmm7,
 		  %xmm8, %xmm9, %xmm10, %xmm11, %xmm12, %xmm13, %xmm14, %xmm15,
 		  %rcx, (%r9));
-	ret;
+	RET;
 SYM_FUNC_END(roundsm16_x0_x1_x2_x3_x4_x5_x6_x7_y0_y1_y2_y3_y4_y5_y6_y7_cd)
 
 .align 8
@@ -200,7 +200,7 @@
 	roundsm16(%xmm4, %xmm5, %xmm6, %xmm7, %xmm0, %xmm1, %xmm2, %xmm3,
 		  %xmm12, %xmm13, %xmm14, %xmm15, %xmm8, %xmm9, %xmm10, %xmm11,
 		  %rax, (%r9));
-	ret;
+	RET;
 SYM_FUNC_END(roundsm16_x4_x5_x6_x7_x0_x1_x2_x3_y4_y5_y6_y7_y0_y1_y2_y3_ab)
 
 /*
@@ -778,7 +778,7 @@
 		    %xmm15, (key_table)(CTX, %r8, 8), (%rax), 1 * 16(%rax));
 
 	FRAME_END
-	ret;
+	RET;
 
 .align 8
 .Lenc_max32:
@@ -865,7 +865,7 @@
 		    %xmm15, (key_table)(CTX), (%rax), 1 * 16(%rax));
 
 	FRAME_END
-	ret;
+	RET;
 
 .align 8
 .Ldec_max32:
@@ -906,7 +906,7 @@
 		     %xmm8, %rsi);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(camellia_ecb_enc_16way)
 
 SYM_FUNC_START(camellia_ecb_dec_16way)
@@ -936,7 +936,7 @@
 		     %xmm8, %rsi);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(camellia_ecb_dec_16way)
 
 SYM_FUNC_START(camellia_cbc_dec_16way)
@@ -987,5 +987,5 @@
 		     %xmm8, %rsi);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(camellia_cbc_dec_16way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/camellia-aesni-avx2-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/camellia-aesni-avx2-asm_64.S
@@ -226,7 +226,7 @@
 	roundsm32(%ymm0, %ymm1, %ymm2, %ymm3, %ymm4, %ymm5, %ymm6, %ymm7,
 		  %ymm8, %ymm9, %ymm10, %ymm11, %ymm12, %ymm13, %ymm14, %ymm15,
 		  %rcx, (%r9));
-	ret;
+	RET;
 SYM_FUNC_END(roundsm32_x0_x1_x2_x3_x4_x5_x6_x7_y0_y1_y2_y3_y4_y5_y6_y7_cd)
 
 .align 8
@@ -234,7 +234,7 @@
 	roundsm32(%ymm4, %ymm5, %ymm6, %ymm7, %ymm0, %ymm1, %ymm2, %ymm3,
 		  %ymm12, %ymm13, %ymm14, %ymm15, %ymm8, %ymm9, %ymm10, %ymm11,
 		  %rax, (%r9));
-	ret;
+	RET;
 SYM_FUNC_END(roundsm32_x4_x5_x6_x7_x0_x1_x2_x3_y4_y5_y6_y7_y0_y1_y2_y3_ab)
 
 /*
@@ -814,7 +814,7 @@
 		    %ymm15, (key_table)(CTX, %r8, 8), (%rax), 1 * 32(%rax));
 
 	FRAME_END
-	ret;
+	RET;
 
 .align 8
 .Lenc_max32:
@@ -901,7 +901,7 @@
 		    %ymm15, (key_table)(CTX), (%rax), 1 * 32(%rax));
 
 	FRAME_END
-	ret;
+	RET;
 
 .align 8
 .Ldec_max32:
@@ -946,7 +946,7 @@
 	vzeroupper;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(camellia_ecb_enc_32way)
 
 SYM_FUNC_START(camellia_ecb_dec_32way)
@@ -980,7 +980,7 @@
 	vzeroupper;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(camellia_ecb_dec_32way)
 
 SYM_FUNC_START(camellia_cbc_dec_32way)
@@ -1047,5 +1047,5 @@
 
 	addq $(16 * 32), %rsp;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(camellia_cbc_dec_32way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/camellia-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/camellia-x86_64-asm_64.S
@@ -213,13 +213,13 @@
 	enc_outunpack(mov, RT1);
 
 	movq RR12, %r12;
-	ret;
+	RET;
 
 .L__enc_xor:
 	enc_outunpack(xor, RT1);
 
 	movq RR12, %r12;
-	ret;
+	RET;
 SYM_FUNC_END(__camellia_enc_blk)
 
 SYM_FUNC_START(camellia_dec_blk)
@@ -257,7 +257,7 @@
 	dec_outunpack();
 
 	movq RR12, %r12;
-	ret;
+	RET;
 SYM_FUNC_END(camellia_dec_blk)
 
 /**********************************************************************
@@ -448,14 +448,14 @@
 
 	movq RR12, %r12;
 	popq %rbx;
-	ret;
+	RET;
 
 .L__enc2_xor:
 	enc_outunpack2(xor, RT2);
 
 	movq RR12, %r12;
 	popq %rbx;
-	ret;
+	RET;
 SYM_FUNC_END(__camellia_enc_blk_2way)
 
 SYM_FUNC_START(camellia_dec_blk_2way)
@@ -495,5 +495,5 @@
 
 	movq RR12, %r12;
 	movq RXOR, %rbx;
-	ret;
+	RET;
 SYM_FUNC_END(camellia_dec_blk_2way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/cast5-avx-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/cast5-avx-x86_64-asm_64.S
@@ -279,7 +279,7 @@
 	outunpack_blocks(RR3, RL3, RTMP, RX, RKM);
 	outunpack_blocks(RR4, RL4, RTMP, RX, RKM);
 
-	ret;
+	RET;
 SYM_FUNC_END(__cast5_enc_blk16)
 
 .align 16
@@ -352,7 +352,7 @@
 	outunpack_blocks(RR3, RL3, RTMP, RX, RKM);
 	outunpack_blocks(RR4, RL4, RTMP, RX, RKM);
 
-	ret;
+	RET;
 
 .L__skip_dec:
 	vpsrldq $4, RKR, RKR;
@@ -393,7 +393,7 @@
 
 	popq %r15;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast5_ecb_enc_16way)
 
 SYM_FUNC_START(cast5_ecb_dec_16way)
@@ -431,7 +431,7 @@
 
 	popq %r15;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast5_ecb_dec_16way)
 
 SYM_FUNC_START(cast5_cbc_dec_16way)
@@ -483,7 +483,7 @@
 	popq %r15;
 	popq %r12;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast5_cbc_dec_16way)
 
 SYM_FUNC_START(cast5_ctr_16way)
@@ -559,5 +559,5 @@
 	popq %r15;
 	popq %r12;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast5_ctr_16way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/cast6-avx-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/cast6-avx-x86_64-asm_64.S
@@ -289,7 +289,7 @@
 	outunpack_blocks(RA1, RB1, RC1, RD1, RTMP, RX, RKRF, RKM);
 	outunpack_blocks(RA2, RB2, RC2, RD2, RTMP, RX, RKRF, RKM);
 
-	ret;
+	RET;
 SYM_FUNC_END(__cast6_enc_blk8)
 
 .align 8
@@ -336,7 +336,7 @@
 	outunpack_blocks(RA1, RB1, RC1, RD1, RTMP, RX, RKRF, RKM);
 	outunpack_blocks(RA2, RB2, RC2, RD2, RTMP, RX, RKRF, RKM);
 
-	ret;
+	RET;
 SYM_FUNC_END(__cast6_dec_blk8)
 
 SYM_FUNC_START(cast6_ecb_enc_8way)
@@ -359,7 +359,7 @@
 
 	popq %r15;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast6_ecb_enc_8way)
 
 SYM_FUNC_START(cast6_ecb_dec_8way)
@@ -382,7 +382,7 @@
 
 	popq %r15;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast6_ecb_dec_8way)
 
 SYM_FUNC_START(cast6_cbc_dec_8way)
@@ -408,5 +408,5 @@
 	popq %r15;
 	popq %r12;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(cast6_cbc_dec_8way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/chacha-avx2-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/chacha-avx2-x86_64.S
@@ -193,7 +193,7 @@
 
 .Ldone2:
 	vzeroupper
-	ret
+	RET
 
 .Lxorpart2:
 	# xor remaining bytes from partial register into output
@@ -498,7 +498,7 @@
 
 .Ldone4:
 	vzeroupper
-	ret
+	RET
 
 .Lxorpart4:
 	# xor remaining bytes from partial register into output
@@ -992,7 +992,7 @@
 .Ldone8:
 	vzeroupper
 	lea		-8(%r10),%rsp
-	ret
+	RET
 
 .Lxorpart8:
 	# xor remaining bytes from partial register into output
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/chacha-avx512vl-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/chacha-avx512vl-x86_64.S
@@ -166,13 +166,13 @@
 
 .Ldone2:
 	vzeroupper
-	ret
+	RET
 
 .Lxorpart2:
 	# xor remaining bytes from partial register into output
 	mov		%rcx,%rax
 	and		$0xf,%rcx
-	jz		.Ldone8
+	jz		.Ldone2
 	mov		%rax,%r9
 	and		$~0xf,%r9
 
@@ -432,13 +432,13 @@
 
 .Ldone4:
 	vzeroupper
-	ret
+	RET
 
 .Lxorpart4:
 	# xor remaining bytes from partial register into output
 	mov		%rcx,%rax
 	and		$0xf,%rcx
-	jz		.Ldone8
+	jz		.Ldone4
 	mov		%rax,%r9
 	and		$~0xf,%r9
 
@@ -812,7 +812,7 @@
 
 .Ldone8:
 	vzeroupper
-	ret
+	RET
 
 .Lxorpart8:
 	# xor remaining bytes from partial register into output
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/chacha-ssse3-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/chacha-ssse3-x86_64.S
@@ -108,7 +108,7 @@
 	sub		$2,%r8d
 	jnz		.Ldoubleround
 
-	ret
+	RET
 SYM_FUNC_END(chacha_permute)
 
 SYM_FUNC_START(chacha_block_xor_ssse3)
@@ -166,7 +166,7 @@
 
 .Ldone:
 	FRAME_END
-	ret
+	RET
 
 .Lxorpart:
 	# xor remaining bytes from partial register into output
@@ -217,7 +217,7 @@
 	movdqu		%xmm3,0x10(%rsi)
 
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(hchacha_block_ssse3)
 
 SYM_FUNC_START(chacha_4block_xor_ssse3)
@@ -762,7 +762,7 @@
 
 .Ldone4:
 	lea		-8(%r10),%rsp
-	ret
+	RET
 
 .Lxorpart4:
 	# xor remaining bytes from partial register into output
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/crc32-pclmul_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/crc32-pclmul_asm.S
@@ -236,5 +236,5 @@
 	pxor    %xmm2, %xmm1
 	pextrd  $0x01, %xmm1, %eax
 
-	ret
+	RET
 SYM_FUNC_END(crc32_pclmul_le_16)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/crc32c-pcl-intel-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/crc32c-pcl-intel-asm_64.S
@@ -306,7 +306,7 @@
 	popq    %rsi
 	popq    %rdi
 	popq    %rbx
-        ret
+        RET
 SYM_FUNC_END(crc_pcl)
 
 .section	.rodata, "a", @progbits
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/crct10dif-pcl-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/crct10dif-pcl-asm_64.S
@@ -257,7 +257,7 @@
 	# Final CRC value (x^16 * M(x)) mod G(x) is in low 16 bits of xmm0.
 
 	pextrw	$0, %xmm0, %eax
-	ret
+	RET
 
 .align 16
 .Lless_than_256_bytes:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/des3_ede-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/des3_ede-asm_64.S
@@ -243,7 +243,7 @@
 	popq %r12;
 	popq %rbx;
 
-	ret;
+	RET;
 SYM_FUNC_END(des3_ede_x86_64_crypt_blk)
 
 /***********************************************************************
@@ -528,7 +528,7 @@
 	popq %r12;
 	popq %rbx;
 
-	ret;
+	RET;
 SYM_FUNC_END(des3_ede_x86_64_crypt_blk_3way)
 
 .section	.rodata, "a", @progbits
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/ghash-clmulni-intel_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/ghash-clmulni-intel_asm.S
@@ -85,7 +85,7 @@
 	psrlq $1, T2
 	pxor T2, T1
 	pxor T1, DATA
-	ret
+	RET
 SYM_FUNC_END(__clmul_gf128mul_ble)
 
 /* void clmul_ghash_mul(char *dst, const u128 *shash) */
@@ -99,7 +99,7 @@
 	pshufb BSWAP, DATA
 	movups DATA, (%rdi)
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(clmul_ghash_mul)
 
 /*
@@ -128,5 +128,5 @@
 	movups DATA, (%rdi)
 .Lupdate_just_ret:
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(clmul_ghash_update)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/ghash-clmulni-intel_glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/ghash-clmulni-intel_glue.c
@@ -19,6 +19,7 @@
 #include <crypto/internal/simd.h>
 #include <asm/cpu_device_id.h>
 #include <asm/simd.h>
+#include <asm/unaligned.h>
 
 #define GHASH_BLOCK_SIZE	16
 #define GHASH_DIGEST_SIZE	16
@@ -54,15 +55,14 @@
 			const u8 *key, unsigned int keylen)
 {
 	struct ghash_ctx *ctx = crypto_shash_ctx(tfm);
-	be128 *x = (be128 *)key;
 	u64 a, b;
 
 	if (keylen != GHASH_BLOCK_SIZE)
 		return -EINVAL;
 
 	/* perform multiplication by 'x' in GF(2^128) */
-	a = be64_to_cpu(x->a);
-	b = be64_to_cpu(x->b);
+	a = get_unaligned_be64(key);
+	b = get_unaligned_be64(key + 8);
 
 	ctx->shash.a = (b << 1) | (a >> 63);
 	ctx->shash.b = (a << 1) | (b >> 63);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/nh-avx2-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/nh-avx2-x86_64.S
@@ -153,5 +153,6 @@
 	vpaddq		T1, T0, T0
 	vpaddq		T4, T0, T0
 	vmovdqu		T0, (HASH)
-	ret
+	vzeroupper
+	RET
 SYM_FUNC_END(nh_avx2)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/nh-sse2-x86_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/nh-sse2-x86_64.S
@@ -119,5 +119,5 @@
 	paddq		PASS2_SUMS, T1
 	movdqu		T0, 0x00(HASH)
 	movdqu		T1, 0x10(HASH)
-	ret
+	RET
 SYM_FUNC_END(nh_sse2)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/poly1305-x86_64-cryptogams.pl
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/poly1305-x86_64-cryptogams.pl
@@ -297,7 +297,7 @@
 $code.=<<___;
 	mov	\$1,%eax
 .Lno_key:
-	ret
+	RET
 ___
 &end_function("poly1305_init_x86_64");
 
@@ -373,7 +373,7 @@
 .cfi_adjust_cfa_offset	-48
 .Lno_data:
 .Lblocks_epilogue:
-	ret
+	RET
 .cfi_endproc
 ___
 &end_function("poly1305_blocks_x86_64");
@@ -399,7 +399,7 @@
 	mov	%rax,0($mac)	# write result
 	mov	%rcx,8($mac)
 
-	ret
+	RET
 ___
 &end_function("poly1305_emit_x86_64");
 if ($avx) {
@@ -429,7 +429,7 @@
 	&poly1305_iteration();
 $code.=<<___;
 	pop $ctx
-	ret
+	RET
 .size	__poly1305_block,.-__poly1305_block
 
 .type	__poly1305_init_avx,\@abi-omnipotent
@@ -594,7 +594,7 @@
 
 	lea	-48-64($ctx),$ctx	# size [de-]optimization
 	pop %rbp
-	ret
+	RET
 .size	__poly1305_init_avx,.-__poly1305_init_avx
 ___
 
@@ -747,7 +747,7 @@
 .cfi_restore	%rbp
 .Lno_data_avx:
 .Lblocks_avx_epilogue:
-	ret
+	RET
 .cfi_endproc
 
 .align	32
@@ -1452,7 +1452,7 @@
 ___
 $code.=<<___;
 	vzeroupper
-	ret
+	RET
 .cfi_endproc
 ___
 &end_function("poly1305_blocks_avx");
@@ -1508,7 +1508,7 @@
 	mov	%rax,0($mac)	# write result
 	mov	%rcx,8($mac)
 
-	ret
+	RET
 ___
 &end_function("poly1305_emit_avx");
 
@@ -1675,7 +1675,7 @@
 .cfi_restore 	%rbp
 .Lno_data_avx2$suffix:
 .Lblocks_avx2_epilogue$suffix:
-	ret
+	RET
 .cfi_endproc
 
 .align	32
@@ -2201,7 +2201,7 @@
 ___
 $code.=<<___;
 	vzeroupper
-	ret
+	RET
 .cfi_endproc
 ___
 if($avx > 2 && $avx512) {
@@ -2792,7 +2792,7 @@
 .cfi_def_cfa_register	%rsp
 ___
 $code.=<<___;
-	ret
+	RET
 .cfi_endproc
 ___
 
@@ -2893,7 +2893,7 @@
 ___
 $code.=<<___;
 	mov	\$1,%eax
-	ret
+	RET
 .size	poly1305_init_base2_44,.-poly1305_init_base2_44
 ___
 {
@@ -3010,7 +3010,7 @@
 	jnz		.Lblocks_vpmadd52_4x
 
 .Lno_data_vpmadd52:
-	ret
+	RET
 .size	poly1305_blocks_vpmadd52,.-poly1305_blocks_vpmadd52
 ___
 }
@@ -3451,7 +3451,7 @@
 	vzeroall
 
 .Lno_data_vpmadd52_4x:
-	ret
+	RET
 .size	poly1305_blocks_vpmadd52_4x,.-poly1305_blocks_vpmadd52_4x
 ___
 }
@@ -3824,7 +3824,7 @@
 	vzeroall
 
 .Lno_data_vpmadd52_8x:
-	ret
+	RET
 .size	poly1305_blocks_vpmadd52_8x,.-poly1305_blocks_vpmadd52_8x
 ___
 }
@@ -3861,7 +3861,7 @@
 	mov	%rax,0($mac)	# write result
 	mov	%rcx,8($mac)
 
-	ret
+	RET
 .size	poly1305_emit_base2_44,.-poly1305_emit_base2_44
 ___
 }	}	}
@@ -3916,7 +3916,7 @@
 
 .Ldone_enc:
 	mov	$otp,%rax
-	ret
+	RET
 .size	xor128_encrypt_n_pad,.-xor128_encrypt_n_pad
 
 .globl	xor128_decrypt_n_pad
@@ -3967,7 +3967,7 @@
 
 .Ldone_dec:
 	mov	$otp,%rax
-	ret
+	RET
 .size	xor128_decrypt_n_pad,.-xor128_decrypt_n_pad
 ___
 }
@@ -4109,7 +4109,7 @@
 	pop	%rbx
 	pop	%rdi
 	pop	%rsi
-	ret
+	RET
 .size	avx_handler,.-avx_handler
 
 .section	.pdata
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/serpent-avx-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/serpent-avx-x86_64-asm_64.S
@@ -601,7 +601,7 @@
 	write_blocks(RA1, RB1, RC1, RD1, RK0, RK1, RK2);
 	write_blocks(RA2, RB2, RC2, RD2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__serpent_enc_blk8_avx)
 
 .align 8
@@ -655,7 +655,7 @@
 	write_blocks(RC1, RD1, RB1, RE1, RK0, RK1, RK2);
 	write_blocks(RC2, RD2, RB2, RE2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__serpent_dec_blk8_avx)
 
 SYM_FUNC_START(serpent_ecb_enc_8way_avx)
@@ -673,7 +673,7 @@
 	store_8way(%rsi, RA1, RB1, RC1, RD1, RA2, RB2, RC2, RD2);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(serpent_ecb_enc_8way_avx)
 
 SYM_FUNC_START(serpent_ecb_dec_8way_avx)
@@ -691,7 +691,7 @@
 	store_8way(%rsi, RC1, RD1, RB1, RE1, RC2, RD2, RB2, RE2);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(serpent_ecb_dec_8way_avx)
 
 SYM_FUNC_START(serpent_cbc_dec_8way_avx)
@@ -709,5 +709,5 @@
 	store_cbc_8way(%rdx, %rsi, RC1, RD1, RB1, RE1, RC2, RD2, RB2, RE2);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(serpent_cbc_dec_8way_avx)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/serpent-avx2-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/serpent-avx2-asm_64.S
@@ -601,7 +601,7 @@
 	write_blocks(RA1, RB1, RC1, RD1, RK0, RK1, RK2);
 	write_blocks(RA2, RB2, RC2, RD2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__serpent_enc_blk16)
 
 .align 8
@@ -655,7 +655,7 @@
 	write_blocks(RC1, RD1, RB1, RE1, RK0, RK1, RK2);
 	write_blocks(RC2, RD2, RB2, RE2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__serpent_dec_blk16)
 
 SYM_FUNC_START(serpent_ecb_enc_16way)
@@ -677,7 +677,7 @@
 	vzeroupper;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(serpent_ecb_enc_16way)
 
 SYM_FUNC_START(serpent_ecb_dec_16way)
@@ -699,7 +699,7 @@
 	vzeroupper;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(serpent_ecb_dec_16way)
 
 SYM_FUNC_START(serpent_cbc_dec_16way)
@@ -722,5 +722,5 @@
 	vzeroupper;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(serpent_cbc_dec_16way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/serpent-sse2-i586-asm_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/serpent-sse2-i586-asm_32.S
@@ -553,12 +553,12 @@
 
 	write_blocks(%eax, RA, RB, RC, RD, RT0, RT1, RE);
 
-	ret;
+	RET;
 
 .L__enc_xor4:
 	xor_blocks(%eax, RA, RB, RC, RD, RT0, RT1, RE);
 
-	ret;
+	RET;
 SYM_FUNC_END(__serpent_enc_blk_4way)
 
 SYM_FUNC_START(serpent_dec_blk_4way)
@@ -612,5 +612,5 @@
 	movl arg_dst(%esp), %eax;
 	write_blocks(%eax, RC, RD, RB, RE, RT0, RT1, RA);
 
-	ret;
+	RET;
 SYM_FUNC_END(serpent_dec_blk_4way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/serpent-sse2-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/serpent-sse2-x86_64-asm_64.S
@@ -675,13 +675,13 @@
 	write_blocks(%rsi, RA1, RB1, RC1, RD1, RK0, RK1, RK2);
 	write_blocks(%rax, RA2, RB2, RC2, RD2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 
 .L__enc_xor8:
 	xor_blocks(%rsi, RA1, RB1, RC1, RD1, RK0, RK1, RK2);
 	xor_blocks(%rax, RA2, RB2, RC2, RD2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__serpent_enc_blk_8way)
 
 SYM_FUNC_START(serpent_dec_blk_8way)
@@ -735,5 +735,5 @@
 	write_blocks(%rsi, RC1, RD1, RB1, RE1, RK0, RK1, RK2);
 	write_blocks(%rax, RC2, RD2, RB2, RE2, RK0, RK1, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(serpent_dec_blk_8way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha1_avx2_x86_64_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha1_avx2_x86_64_asm.S
@@ -674,7 +674,7 @@
 	pop	%r12
 	pop	%rbx
 
-	ret
+	RET
 
 	SYM_FUNC_END(\name)
 .endm
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha1_ni_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha1_ni_asm.S
@@ -290,7 +290,7 @@
 	mov		%rbp, %rsp
 	pop		%rbp
 
-	ret
+	RET
 SYM_FUNC_END(sha1_ni_transform)
 
 .section	.rodata.cst16.PSHUFFLE_BYTE_FLIP_MASK, "aM", @progbits, 16
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha1_ssse3_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha1_ssse3_asm.S
@@ -99,7 +99,7 @@
 	pop	%rbp
 	pop	%r12
 	pop	%rbx
-	ret
+	RET
 
 	SYM_FUNC_END(\name)
 .endm
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha1_ssse3_glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha1_ssse3_glue.c
@@ -24,8 +24,17 @@
 #include <linux/types.h>
 #include <crypto/sha1.h>
 #include <crypto/sha1_base.h>
+#include <asm/cpu_device_id.h>
 #include <asm/simd.h>
 
+static const struct x86_cpu_id module_cpu_ids[] = {
+	X86_MATCH_FEATURE(X86_FEATURE_AVX2, NULL),
+	X86_MATCH_FEATURE(X86_FEATURE_AVX, NULL),
+	X86_MATCH_FEATURE(X86_FEATURE_SSSE3, NULL),
+	{}
+};
+MODULE_DEVICE_TABLE(x86cpu, module_cpu_ids);
+
 static int sha1_update(struct shash_desc *desc, const u8 *data,
 			     unsigned int len, sha1_block_fn *sha1_xform)
 {
@@ -301,6 +310,9 @@
 
 static int __init sha1_ssse3_mod_init(void)
 {
+	if (!x86_match_cpu(module_cpu_ids))
+		return -ENODEV;
+
 	if (register_sha1_ssse3())
 		goto fail;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha256-avx-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha256-avx-asm.S
@@ -458,7 +458,7 @@
 	popq    %r13
 	popq	%r12
 	popq    %rbx
-	ret
+	RET
 SYM_FUNC_END(sha256_transform_avx)
 
 .section	.rodata.cst256.K256, "aM", @progbits, 256
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha256-avx2-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha256-avx2-asm.S
@@ -710,7 +710,8 @@
 	popq	%r13
 	popq	%r12
 	popq	%rbx
-	ret
+	vzeroupper
+	RET
 SYM_FUNC_END(sha256_transform_rorx)
 
 .section	.rodata.cst512.K256, "aM", @progbits, 512
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha256-ssse3-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha256-ssse3-asm.S
@@ -472,7 +472,7 @@
 	popq    %r12
 	popq    %rbx
 
-	ret
+	RET
 SYM_FUNC_END(sha256_transform_ssse3)
 
 .section	.rodata.cst256.K256, "aM", @progbits, 256
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha256_ni_asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha256_ni_asm.S
@@ -326,7 +326,7 @@
 
 .Ldone_hash:
 
-	ret
+	RET
 SYM_FUNC_END(sha256_ni_transform)
 
 .section	.rodata.cst256.K256, "aM", @progbits, 256
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha256_ssse3_glue.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha256_ssse3_glue.c
@@ -38,11 +38,20 @@
 #include <crypto/sha2.h>
 #include <crypto/sha256_base.h>
 #include <linux/string.h>
+#include <asm/cpu_device_id.h>
 #include <asm/simd.h>
 
 asmlinkage void sha256_transform_ssse3(struct sha256_state *state,
 				       const u8 *data, int blocks);
 
+static const struct x86_cpu_id module_cpu_ids[] = {
+	X86_MATCH_FEATURE(X86_FEATURE_AVX2, NULL),
+	X86_MATCH_FEATURE(X86_FEATURE_AVX, NULL),
+	X86_MATCH_FEATURE(X86_FEATURE_SSSE3, NULL),
+	{}
+};
+MODULE_DEVICE_TABLE(x86cpu, module_cpu_ids);
+
 static int _sha256_update(struct shash_desc *desc, const u8 *data,
 			  unsigned int len, sha256_block_fn *sha256_xform)
 {
@@ -366,6 +375,9 @@
 
 static int __init sha256_ssse3_mod_init(void)
 {
+	if (!x86_match_cpu(module_cpu_ids))
+		return -ENODEV;
+
 	if (register_sha256_ssse3())
 		goto fail;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha512-avx-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha512-avx-asm.S
@@ -361,7 +361,7 @@
 	pop	%rbx
 
 nowork:
-	ret
+	RET
 SYM_FUNC_END(sha512_transform_avx)
 
 ########################################################################
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha512-avx2-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha512-avx2-asm.S
@@ -679,7 +679,8 @@
 	pop	%r12
 	pop	%rbx
 
-	ret
+	vzeroupper
+	RET
 SYM_FUNC_END(sha512_transform_rorx)
 
 ########################################################################
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sha512-ssse3-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sha512-ssse3-asm.S
@@ -363,7 +363,7 @@
 	pop	%rbx
 
 nowork:
-	ret
+	RET
 SYM_FUNC_END(sha512_transform_ssse3)
 
 ########################################################################
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sm4-aesni-avx-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sm4-aesni-avx-asm_64.S
@@ -246,7 +246,7 @@
 .Lblk4_store_output_done:
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx_crypt4)
 
 .align 8
@@ -356,7 +356,7 @@
 	vpshufb RTMP2, RB3, RB3;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(__sm4_crypt_blk8)
 
 /*
@@ -412,7 +412,7 @@
 .Lblk8_store_output_done:
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx_crypt8)
 
 /*
@@ -487,7 +487,7 @@
 
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx_ctr_enc_blk8)
 
 /*
@@ -537,7 +537,7 @@
 
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx_cbc_dec_blk8)
 
 /*
@@ -590,5 +590,5 @@
 
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx_cfb_dec_blk8)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/sm4-aesni-avx2-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/sm4-aesni-avx2-asm_64.S
@@ -268,7 +268,7 @@
 	vpshufb RTMP2, RB3, RB3;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(__sm4_crypt_blk16)
 
 #define inc_le128(x, minus_one, tmp) \
@@ -387,7 +387,7 @@
 
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx2_ctr_enc_blk16)
 
 /*
@@ -441,7 +441,7 @@
 
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx2_cbc_dec_blk16)
 
 /*
@@ -497,5 +497,5 @@
 
 	vzeroall;
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(sm4_aesni_avx2_cfb_dec_blk16)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/twofish-avx-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/twofish-avx-x86_64-asm_64.S
@@ -267,7 +267,7 @@
 	outunpack_blocks(RC1, RD1, RA1, RB1, RK1, RX0, RY0, RK2);
 	outunpack_blocks(RC2, RD2, RA2, RB2, RK1, RX0, RY0, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__twofish_enc_blk8)
 
 .align 8
@@ -307,7 +307,7 @@
 	outunpack_blocks(RA1, RB1, RC1, RD1, RK1, RX0, RY0, RK2);
 	outunpack_blocks(RA2, RB2, RC2, RD2, RK1, RX0, RY0, RK2);
 
-	ret;
+	RET;
 SYM_FUNC_END(__twofish_dec_blk8)
 
 SYM_FUNC_START(twofish_ecb_enc_8way)
@@ -327,7 +327,7 @@
 	store_8way(%r11, RC1, RD1, RA1, RB1, RC2, RD2, RA2, RB2);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(twofish_ecb_enc_8way)
 
 SYM_FUNC_START(twofish_ecb_dec_8way)
@@ -347,7 +347,7 @@
 	store_8way(%r11, RA1, RB1, RC1, RD1, RA2, RB2, RC2, RD2);
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(twofish_ecb_dec_8way)
 
 SYM_FUNC_START(twofish_cbc_dec_8way)
@@ -372,5 +372,5 @@
 	popq %r12;
 
 	FRAME_END
-	ret;
+	RET;
 SYM_FUNC_END(twofish_cbc_dec_8way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/twofish-i586-asm_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/twofish-i586-asm_32.S
@@ -260,7 +260,7 @@
 	pop	%ebx
 	pop	%ebp
 	mov	$1,	%eax
-	ret
+	RET
 SYM_FUNC_END(twofish_enc_blk)
 
 SYM_FUNC_START(twofish_dec_blk)
@@ -317,5 +317,5 @@
 	pop	%ebx
 	pop	%ebp
 	mov	$1,	%eax
-	ret
+	RET
 SYM_FUNC_END(twofish_dec_blk)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/twofish-x86_64-asm_64-3way.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/twofish-x86_64-asm_64-3way.S
@@ -258,7 +258,7 @@
 	popq %rbx;
 	popq %r12;
 	popq %r13;
-	ret;
+	RET;
 
 .L__enc_xor3:
 	outunpack_enc3(xor);
@@ -266,7 +266,7 @@
 	popq %rbx;
 	popq %r12;
 	popq %r13;
-	ret;
+	RET;
 SYM_FUNC_END(__twofish_enc_blk_3way)
 
 SYM_FUNC_START(twofish_dec_blk_3way)
@@ -301,5 +301,5 @@
 	popq %rbx;
 	popq %r12;
 	popq %r13;
-	ret;
+	RET;
 SYM_FUNC_END(twofish_dec_blk_3way)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/crypto/twofish-x86_64-asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/crypto/twofish-x86_64-asm_64.S
@@ -252,7 +252,7 @@
 
 	popq	R1
 	movl	$1,%eax
-	ret
+	RET
 SYM_FUNC_END(twofish_enc_blk)
 
 SYM_FUNC_START(twofish_dec_blk)
@@ -304,5 +304,5 @@
 
 	popq	R1
 	movl	$1,%eax
-	ret
+	RET
 SYM_FUNC_END(twofish_dec_blk)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/Makefile
@@ -11,12 +11,13 @@
 
 CFLAGS_common.o			+= -fno-stack-protector
 
-obj-y				:= entry_$(BITS).o thunk_$(BITS).o syscall_$(BITS).o
+obj-y				:= entry.o entry_$(BITS).o syscall_$(BITS).o
 obj-y				+= common.o
 
 obj-y				+= vdso/
 obj-y				+= vsyscall/
 
+obj-$(CONFIG_PREEMPTION)	+= thunk_$(BITS).o
 obj-$(CONFIG_IA32_EMULATION)	+= entry_64_compat.o syscall_32.o
 obj-$(CONFIG_X86_X32_ABI)	+= syscall_x32.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/calling.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/calling.h
@@ -7,6 +7,8 @@
 #include <asm/asm-offsets.h>
 #include <asm/processor-flags.h>
 #include <asm/ptrace-abi.h>
+#include <asm/msr.h>
+#include <asm/nospec-branch.h>
 
 /*
 
@@ -68,6 +70,8 @@
 	pushq	%rsi		/* pt_regs->si */
 	movq	8(%rsp), %rsi	/* temporarily store the return address in %rsi */
 	movq	%rdi, 8(%rsp)	/* pt_regs->di (overwriting original return address) */
+	/* We just clobbered the return address - use the IRET frame for unwinding: */
+	UNWIND_HINT_IRET_REGS offset=3*8
 	.else
 	pushq   %rdi		/* pt_regs->di */
 	pushq   %rsi		/* pt_regs->si */
@@ -119,27 +123,19 @@
 	CLEAR_REGS
 .endm
 
-.macro POP_REGS pop_rdi=1 skip_r11rcx=0
+.macro POP_REGS pop_rdi=1
 	popq %r15
 	popq %r14
 	popq %r13
 	popq %r12
 	popq %rbp
 	popq %rbx
-	.if \skip_r11rcx
-	popq %rsi
-	.else
 	popq %r11
-	.endif
 	popq %r10
 	popq %r9
 	popq %r8
 	popq %rax
-	.if \skip_r11rcx
-	popq %rsi
-	.else
 	popq %rcx
-	.endif
 	popq %rdx
 	popq %rsi
 	.if \pop_rdi
@@ -290,6 +286,66 @@
 #endif
 
 /*
+ * IBRS kernel mitigation for Spectre_v2.
+ *
+ * Assumes full context is established (PUSH_REGS, CR3 and GS) and it clobbers
+ * the regs it uses (AX, CX, DX). Must be called before the first RET
+ * instruction (NOTE! UNTRAIN_RET includes a RET instruction)
+ *
+ * The optional argument is used to save/restore the current value,
+ * which is used on the paranoid paths.
+ *
+ * Assumes x86_spec_ctrl_{base,current} to have SPEC_CTRL_IBRS set.
+ */
+.macro IBRS_ENTER save_reg
+#ifdef CONFIG_CPU_IBRS_ENTRY
+	ALTERNATIVE "jmp .Lend_\@", "", X86_FEATURE_KERNEL_IBRS
+	movl	$MSR_IA32_SPEC_CTRL, %ecx
+
+.ifnb \save_reg
+	rdmsr
+	shl	$32, %rdx
+	or	%rdx, %rax
+	mov	%rax, \save_reg
+	test	$SPEC_CTRL_IBRS, %eax
+	jz	.Ldo_wrmsr_\@
+	lfence
+	jmp	.Lend_\@
+.Ldo_wrmsr_\@:
+.endif
+
+	movq	PER_CPU_VAR(x86_spec_ctrl_current), %rdx
+	movl	%edx, %eax
+	shr	$32, %rdx
+	wrmsr
+.Lend_\@:
+#endif
+.endm
+
+/*
+ * Similar to IBRS_ENTER, requires KERNEL GS,CR3 and clobbers (AX, CX, DX)
+ * regs. Must be called after the last RET.
+ */
+.macro IBRS_EXIT save_reg
+#ifdef CONFIG_CPU_IBRS_ENTRY
+	ALTERNATIVE "jmp .Lend_\@", "", X86_FEATURE_KERNEL_IBRS
+	movl	$MSR_IA32_SPEC_CTRL, %ecx
+
+.ifnb \save_reg
+	mov	\save_reg, %rdx
+.else
+	movq	PER_CPU_VAR(x86_spec_ctrl_current), %rdx
+	andl	$(~SPEC_CTRL_IBRS), %edx
+.endif
+
+	movl	%edx, %eax
+	shr	$32, %rdx
+	wrmsr
+.Lend_\@:
+#endif
+.endm
+
+/*
  * Mitigate Spectre v1 for conditional swapgs code paths.
  *
  * FENCE_SWAPGS_USER_ENTRY is used in the user entry swapgs code path, to
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/common.c
@@ -25,6 +25,7 @@
 #include <xen/events.h>
 #endif
 
+#include <asm/apic.h>
 #include <asm/desc.h>
 #include <asm/traps.h>
 #include <asm/vdso.h>
@@ -47,7 +48,7 @@
 
 	if (likely(unr < NR_syscalls)) {
 		unr = array_index_nospec(unr, NR_syscalls);
-		regs->ax = sys_call_table[unr](regs);
+		regs->ax = x64_sys_call(regs, unr);
 		return true;
 	}
 	return false;
@@ -64,7 +65,7 @@
 
 	if (IS_ENABLED(CONFIG_X86_X32_ABI) && likely(xnr < X32_NR_syscalls)) {
 		xnr = array_index_nospec(xnr, X32_NR_syscalls);
-		regs->ax = x32_sys_call_table[xnr](regs);
+		regs->ax = x32_sys_call(regs, xnr);
 		return true;
 	}
 	return false;
@@ -96,6 +97,10 @@
 	return (int)regs->orig_ax;
 }
 
+#ifdef CONFIG_IA32_EMULATION
+bool __ia32_enabled __ro_after_init = true;
+#endif
+
 /*
  * Invoke a 32-bit syscall.  Called with IRQs on in CONTEXT_KERNEL.
  */
@@ -109,13 +114,102 @@
 
 	if (likely(unr < IA32_NR_syscalls)) {
 		unr = array_index_nospec(unr, IA32_NR_syscalls);
-		regs->ax = ia32_sys_call_table[unr](regs);
+		regs->ax = ia32_sys_call(regs, unr);
 	} else if (nr != -1) {
 		regs->ax = __ia32_sys_ni_syscall(regs);
 	}
 }
 
-/* Handles int $0x80 */
+#ifdef CONFIG_IA32_EMULATION
+static __always_inline bool int80_is_external(void)
+{
+	const unsigned int offs = (0x80 / 32) * 0x10;
+	const u32 bit = BIT(0x80 % 32);
+
+	/* The local APIC on XENPV guests is fake */
+	if (cpu_feature_enabled(X86_FEATURE_XENPV))
+		return false;
+
+	/*
+	 * If vector 0x80 is set in the APIC ISR then this is an external
+	 * interrupt. Either from broken hardware or injected by a VMM.
+	 *
+	 * Note: In guest mode this is only valid for secure guests where
+	 * the secure module fully controls the vAPIC exposed to the guest.
+	 */
+	return apic_read(APIC_ISR + offs) & bit;
+}
+
+/**
+ * do_int80_emulation - 32-bit legacy syscall C entry from asm
+ *
+ * This entry point can be used by 32-bit and 64-bit programs to perform
+ * 32-bit system calls.  Instances of INT $0x80 can be found inline in
+ * various programs and libraries.  It is also used by the vDSO's
+ * __kernel_vsyscall fallback for hardware that doesn't support a faster
+ * entry method.  Restarted 32-bit system calls also fall back to INT
+ * $0x80 regardless of what instruction was originally used to do the
+ * system call.
+ *
+ * This is considered a slow path.  It is not used by most libc
+ * implementations on modern hardware except during process startup.
+ *
+ * The arguments for the INT $0x80 based syscall are on stack in the
+ * pt_regs structure:
+ *   eax:				system call number
+ *   ebx, ecx, edx, esi, edi, ebp:	arg1 - arg 6
+ */
+__visible noinstr void do_int80_emulation(struct pt_regs *regs)
+{
+	int nr;
+
+	/* Kernel does not use INT $0x80! */
+	if (unlikely(!user_mode(regs))) {
+		irqentry_enter(regs);
+		instrumentation_begin();
+		panic("Unexpected external interrupt 0x80\n");
+	}
+
+	/*
+	 * Establish kernel context for instrumentation, including for
+	 * int80_is_external() below which calls into the APIC driver.
+	 * Identical for soft and external interrupts.
+	 */
+	enter_from_user_mode(regs);
+
+	instrumentation_begin();
+	add_random_kstack_offset();
+
+	/* Validate that this is a soft interrupt to the extent possible */
+	if (unlikely(int80_is_external()))
+		panic("Unexpected external interrupt 0x80\n");
+
+	/*
+	 * The low level idtentry code pushed -1 into regs::orig_ax
+	 * and regs::ax contains the syscall number.
+	 *
+	 * User tracing code (ptrace or signal handlers) might assume
+	 * that the regs::orig_ax contains a 32-bit number on invoking
+	 * a 32-bit syscall.
+	 *
+	 * Establish the syscall convention by saving the 32bit truncated
+	 * syscall number in regs::orig_ax and by invalidating regs::ax.
+	 */
+	regs->orig_ax = regs->ax & GENMASK(31, 0);
+	regs->ax = -ENOSYS;
+
+	nr = syscall_32_enter(regs);
+
+	local_irq_enable();
+	nr = syscall_enter_from_user_mode_work(regs, nr);
+	do_syscall_32_irqs_on(regs, nr);
+
+	instrumentation_end();
+	syscall_exit_to_user_mode(regs);
+}
+#else /* CONFIG_IA32_EMULATION */
+
+/* Handles int $0x80 on a 32bit kernel */
 __visible noinstr void do_int80_syscall_32(struct pt_regs *regs)
 {
 	int nr = syscall_32_enter(regs);
@@ -134,6 +228,7 @@
 	instrumentation_end();
 	syscall_exit_to_user_mode(regs);
 }
+#endif /* !CONFIG_IA32_EMULATION */
 
 static noinstr bool __do_fast_syscall_32(struct pt_regs *regs)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/entry.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/entry.S
@@ -0,0 +1,50 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Common place for both 32- and 64-bit entry routines.
+ */
+
+#include <linux/linkage.h>
+#include <asm/export.h>
+#include <asm/msr-index.h>
+#include <asm/unwind_hints.h>
+#include <asm/segment.h>
+#include <asm/cache.h>
+#include <asm/cpufeatures.h>
+#include <asm/nospec-branch.h>
+
+.pushsection .noinstr.text, "ax"
+
+SYM_FUNC_START(entry_ibpb)
+	movl	$MSR_IA32_PRED_CMD, %ecx
+	movl	$PRED_CMD_IBPB, %eax
+	xorl	%edx, %edx
+	wrmsr
+
+	/* Make sure IBPB clears return stack preductions too. */
+	FILL_RETURN_BUFFER %rax, RSB_CLEAR_LOOPS, X86_BUG_IBPB_NO_RET
+	RET
+SYM_FUNC_END(entry_ibpb)
+/* For KVM */
+EXPORT_SYMBOL_GPL(entry_ibpb);
+
+.popsection
+
+/*
+ * Define the VERW operand that is disguised as entry code so that
+ * it can be referenced with KPTI enabled. This ensure VERW can be
+ * used late in exit-to-user path after page tables are switched.
+ */
+.pushsection .entry.text, "ax"
+
+.align L1_CACHE_BYTES, 0xcc
+SYM_CODE_START_NOALIGN(mds_verw_sel)
+	UNWIND_HINT_EMPTY
+	ANNOTATE_NOENDBR
+	.word __KERNEL_DS
+.align L1_CACHE_BYTES, 0xcc
+SYM_CODE_END(mds_verw_sel);
+/* For KVM */
+EXPORT_SYMBOL_GPL(mds_verw_sel);
+
+.popsection
+
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/entry_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/entry_32.S
@@ -268,19 +268,16 @@
 1:	popl	%ds
 2:	popl	%es
 3:	popl	%fs
-	addl	$(4 + \pop), %esp	/* pop the unused "gs" slot */
+4:	addl	$(4 + \pop), %esp	/* pop the unused "gs" slot */
 	IRET_FRAME
-.pushsection .fixup, "ax"
-4:	movl	$0, (%esp)
-	jmp	1b
-5:	movl	$0, (%esp)
-	jmp	2b
-6:	movl	$0, (%esp)
-	jmp	3b
-.popsection
-	_ASM_EXTABLE(1b, 4b)
-	_ASM_EXTABLE(2b, 5b)
-	_ASM_EXTABLE(3b, 6b)
+
+	/*
+	 * There is no _ASM_EXTABLE_TYPE_REG() for ASM, however since this is
+	 * ASM the registers are known and we can trivially hard-code them.
+	 */
+	_ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_POP_ZERO|EX_REG_DS)
+	_ASM_EXTABLE_TYPE(2b, 3b, EX_TYPE_POP_ZERO|EX_REG_ES)
+	_ASM_EXTABLE_TYPE(3b, 4b, EX_TYPE_POP_ZERO|EX_REG_FS)
 .endm
 
 .macro RESTORE_ALL_NMI cr3_reg:req pop=0
@@ -701,7 +698,6 @@
 	movl	%ebx, PER_CPU_VAR(__stack_chk_guard)
 #endif
 
-#ifdef CONFIG_RETPOLINE
 	/*
 	 * When switching from a shallower to a deeper call stack
 	 * the RSB may either underflow or use entries populated
@@ -710,7 +706,6 @@
 	 * speculative execution to prevent attack.
 	 */
 	FILL_RETURN_BUFFER %ebx, RSB_CLEAR_LOOPS, X86_FEATURE_RSB_CTXSW
-#endif
 
 	/* Restore flags or the incoming task to restore AC state. */
 	popfl
@@ -740,7 +735,7 @@
 	popl	%eax
 
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(schedule_tail_wrapper)
 .popsection
 
@@ -907,6 +902,8 @@
 
 	/* Now ready to switch the cr3 */
 	SWITCH_TO_USER_CR3 scratch_reg=%eax
+	/* Clobbers ZF */
+	CLEAR_CPU_BUFFERS
 
 	/*
 	 * Restore all flags except IF. (We restore IF separately because
@@ -925,10 +922,8 @@
 	sti
 	sysexit
 
-.pushsection .fixup, "ax"
-2:	movl	$0, PT_FS(%esp)
-	jmp	1b
-.popsection
+2:	movl    $0, PT_FS(%esp)
+	jmp     1b
 	_ASM_EXTABLE(1b, 2b)
 
 .Lsysenter_fix_flags:
@@ -988,6 +983,7 @@
 
 	/* Restore user state */
 	RESTORE_REGS pop=4			# skip orig_eax/error_code
+	CLEAR_CPU_BUFFERS
 .Lirq_return:
 	/*
 	 * ARCH_HAS_MEMBARRIER_SYNC_CORE rely on IRET core serialization
@@ -996,8 +992,7 @@
 	 */
 	iret
 
-.section .fixup, "ax"
-SYM_CODE_START(asm_iret_error)
+.Lasm_iret_error:
 	pushl	$0				# no error code
 	pushl	$iret_error
 
@@ -1014,9 +1009,8 @@
 #endif
 
 	jmp	handle_exception
-SYM_CODE_END(asm_iret_error)
-.previous
-	_ASM_EXTABLE(.Lirq_return, asm_iret_error)
+
+	_ASM_EXTABLE(.Lirq_return, .Lasm_iret_error)
 SYM_FUNC_END(entry_INT80_32)
 
 .macro FIXUP_ESPFIX_STACK
@@ -1202,6 +1196,7 @@
 
 	CHECK_AND_APPLY_ESPFIX
 	RESTORE_ALL_NMI cr3_reg=%edi pop=4
+	CLEAR_CPU_BUFFERS
 	jmp	.Lirq_return
 
 #ifdef CONFIG_X86_ESPFIX32
@@ -1243,19 +1238,20 @@
 	 *  1 - orig_ax
 	 */
 	lss	(1+5+6)*4(%esp), %esp			# back to espfix stack
+	CLEAR_CPU_BUFFERS
 	jmp	.Lirq_return
 #endif
 SYM_CODE_END(asm_exc_nmi)
 
 .pushsection .text, "ax"
-SYM_CODE_START(rewind_stack_do_exit)
+SYM_CODE_START(rewind_stack_and_make_dead)
 	/* Prevent any naive code from trying to unwind to our caller. */
 	xorl	%ebp, %ebp
 
 	movl	PER_CPU_VAR(cpu_current_top_of_stack), %esi
 	leal	-TOP_OF_KERNEL_STACK_PADDING-PTREGS_SIZE(%esi), %esp
 
-	call	do_exit
+	call	make_task_dead
 1:	jmp 1b
-SYM_CODE_END(rewind_stack_do_exit)
+SYM_CODE_END(rewind_stack_and_make_dead)
 .popsection
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/entry_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/entry_64.S
@@ -85,7 +85,7 @@
  */
 
 SYM_CODE_START(entry_SYSCALL_64)
-	UNWIND_HINT_EMPTY
+	UNWIND_HINT_ENTRY
 
 	swapgs
 	/* tss.sp2 is scratch space. */
@@ -110,6 +110,12 @@
 	movq	%rsp, %rdi
 	/* Sign extend the lower 32bit as syscall numbers are treated as int */
 	movslq	%eax, %rsi
+
+	/* clobbers %rax, make sure it is after saving the syscall nr */
+	IBRS_ENTER
+	UNTRAIN_RET
+	CLEAR_BRANCH_HISTORY
+
 	call	do_syscall_64		/* returns with IRQs disabled */
 
 	/*
@@ -159,22 +165,9 @@
 	jne	swapgs_restore_regs_and_return_to_usermode
 
 	/*
-	 * SYSCALL clears RF when it saves RFLAGS in R11 and SYSRET cannot
-	 * restore RF properly. If the slowpath sets it for whatever reason, we
-	 * need to restore it correctly.
-	 *
-	 * SYSRET can restore TF, but unlike IRET, restoring TF results in a
-	 * trap from userspace immediately after SYSRET.  This would cause an
-	 * infinite loop whenever #DB happens with register state that satisfies
-	 * the opportunistic SYSRET conditions.  For example, single-stepping
-	 * this user code:
-	 *
-	 *           movq	$stuck_here, %rcx
-	 *           pushfq
-	 *           popq %r11
-	 *   stuck_here:
-	 *
-	 * would never get past 'stuck_here'.
+	 * SYSRET cannot restore RF.  It can restore TF, but unlike IRET,
+	 * restoring TF results in a trap from userspace immediately after
+	 * SYSRET.
 	 */
 	testq	$(X86_EFLAGS_RF|X86_EFLAGS_TF), %r11
 	jnz	swapgs_restore_regs_and_return_to_usermode
@@ -189,8 +182,8 @@
 	 * perf profiles. Nothing jumps here.
 	 */
 syscall_return_via_sysret:
-	/* rcx and r11 are already restored (see code above) */
-	POP_REGS pop_rdi=0 skip_r11rcx=1
+	IBRS_EXIT
+	POP_REGS pop_rdi=0
 
 	/*
 	 * Now all regs are restored except RSP and RDI.
@@ -214,6 +207,7 @@
 	popq	%rdi
 	popq	%rsp
 	swapgs
+	CLEAR_CPU_BUFFERS
 	sysretq
 SYM_CODE_END(entry_SYSCALL_64)
 
@@ -243,7 +237,6 @@
 	movq	%rbx, PER_CPU_VAR(fixed_percpu_data) + stack_canary_offset
 #endif
 
-#ifdef CONFIG_RETPOLINE
 	/*
 	 * When switching from a shallower to a deeper call stack
 	 * the RSB may either underflow or use entries populated
@@ -252,7 +245,6 @@
 	 * speculative execution to prevent attack.
 	 */
 	FILL_RETURN_BUFFER %r12, RSB_CLEAR_LOOPS, X86_FEATURE_RSB_CTXSW
-#endif
 
 	/* restore callee-saved registers */
 	popq	%r15
@@ -315,6 +307,14 @@
 #endif
 .endm
 
+SYM_CODE_START_LOCAL(xen_error_entry)
+	UNWIND_HINT_FUNC
+	PUSH_AND_CLEAR_REGS save_ret=1
+	ENCODE_FRAME_POINTER 8
+	UNTRAIN_RET
+	RET
+SYM_CODE_END(xen_error_entry)
+
 /**
  * idtentry_body - Macro to emit code calling the C function
  * @cfunc:		C function to be called
@@ -322,7 +322,18 @@
  */
 .macro idtentry_body cfunc has_error_code:req
 
-	call	error_entry
+	/*
+	 * Call error_entry() and switch to the task stack if from userspace.
+	 *
+	 * When in XENPV, it is already in the task stack, and it can't fault
+	 * for native_iret() nor native_load_gs_index() since XENPV uses its
+	 * own pvops for IRET and load_gs_index().  And it doesn't need to
+	 * switch the CR3.  So it can skip invoking error_entry().
+	 */
+	ALTERNATIVE "call error_entry; movq %rax, %rsp", \
+		    "call xen_error_entry", X86_FEATURE_XENPV
+
+	ENCODE_FRAME_POINTER
 	UNWIND_HINT_REGS
 
 	movq	%rsp, %rdi			/* pt_regs pointer into 1st argument*/
@@ -351,6 +362,7 @@
 SYM_CODE_START(\asmsym)
 	UNWIND_HINT_IRET_REGS offset=\has_error_code*8
 	ASM_CLAC
+	cld
 
 	.if \has_error_code == 0
 		pushq	$-1			/* ORIG_RAX: no syscall to restart */
@@ -418,6 +430,7 @@
 SYM_CODE_START(\asmsym)
 	UNWIND_HINT_IRET_REGS
 	ASM_CLAC
+	cld
 
 	pushq	$-1			/* ORIG_RAX: no syscall to restart */
 
@@ -473,6 +486,7 @@
 SYM_CODE_START(\asmsym)
 	UNWIND_HINT_IRET_REGS
 	ASM_CLAC
+	cld
 
 	/*
 	 * If the entry is from userspace, switch stacks and treat it as
@@ -499,6 +513,7 @@
 	call	vc_switch_off_ist
 	movq	%rax, %rsp		/* Switch to new stack */
 
+	ENCODE_FRAME_POINTER
 	UNWIND_HINT_REGS
 
 	/* Update pt_regs */
@@ -534,6 +549,7 @@
 SYM_CODE_START(\asmsym)
 	UNWIND_HINT_IRET_REGS offset=8
 	ASM_CLAC
+	cld
 
 	/* paranoid_entry returns GS information for paranoid_exit in EBX. */
 	call	paranoid_entry
@@ -567,6 +583,7 @@
 
 SYM_CODE_START_LOCAL(common_interrupt_return)
 SYM_INNER_LABEL(swapgs_restore_regs_and_return_to_usermode, SYM_L_GLOBAL)
+	IBRS_EXIT
 #ifdef CONFIG_DEBUG_ENTRY
 	/* Assert that pt_regs indicates user mode. */
 	testb	$3, CS(%rsp)
@@ -574,6 +591,10 @@
 	ud2
 1:
 #endif
+#ifdef CONFIG_XEN_PV
+	ALTERNATIVE "", "jmp xenpv_restore_regs_and_return_to_usermode", X86_FEATURE_XENPV
+#endif
+
 	POP_REGS pop_rdi=0
 
 	/*
@@ -605,6 +626,7 @@
 	/* Restore RDI. */
 	popq	%rdi
 	SWAPGS
+	CLEAR_CPU_BUFFERS
 	INTERRUPT_RETURN
 
 
@@ -710,6 +732,8 @@
 	 */
 	popq	%rax				/* Restore user RAX */
 
+	CLEAR_CPU_BUFFERS
+
 	/*
 	 * RSP now points to an ordinary IRET frame, except that the page
 	 * is read-only and RSP[31:16] are preloaded with the userspace
@@ -734,7 +758,7 @@
 2:	ALTERNATIVE "", "mfence", X86_BUG_SWAPGS_FENCE
 	swapgs
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(asm_load_gs_index)
 EXPORT_SYMBOL(asm_load_gs_index)
 
@@ -841,10 +865,12 @@
  *              1 -> no SWAPGS on exit
  *
  *     Y        GSBASE value at entry, must be restored in paranoid_exit
+ *
+ * R14 - old CR3
+ * R15 - old SPEC_CTRL
  */
 SYM_CODE_START_LOCAL(paranoid_entry)
 	UNWIND_HINT_FUNC
-	cld
 	PUSH_AND_CLEAR_REGS save_ret=1
 	ENCODE_FRAME_POINTER 8
 
@@ -885,11 +911,12 @@
 	 * is needed here.
 	 */
 	SAVE_AND_SET_GSBASE scratch_reg=%rax save_reg=%rbx
-	ret
+	jmp .Lparanoid_gsbase_done
 
 .Lparanoid_entry_checkgs:
 	/* EBX = 1 -> kernel GSBASE active, no restore required */
 	movl	$1, %ebx
+
 	/*
 	 * The kernel-enforced convention is a negative GSBASE indicates
 	 * a kernel value. No SWAPGS needed on entry and exit.
@@ -897,22 +924,23 @@
 	movl	$MSR_GS_BASE, %ecx
 	rdmsr
 	testl	%edx, %edx
-	jns	.Lparanoid_entry_swapgs
-	ret
+	js	.Lparanoid_kernel_gsbase
 
-.Lparanoid_entry_swapgs:
+	/* EBX = 0 -> SWAPGS required on exit */
+	xorl	%ebx, %ebx
 	swapgs
+.Lparanoid_kernel_gsbase:
+	FENCE_SWAPGS_KERNEL_ENTRY
+.Lparanoid_gsbase_done:
 
 	/*
-	 * The above SAVE_AND_SWITCH_TO_KERNEL_CR3 macro doesn't do an
-	 * unconditional CR3 write, even in the PTI case.  So do an lfence
-	 * to prevent GS speculation, regardless of whether PTI is enabled.
+	 * Once we have CR3 and %GS setup save and set SPEC_CTRL. Just like
+	 * CR3 above, keep the old value in a callee saved register.
 	 */
-	FENCE_SWAPGS_KERNEL_ENTRY
+	IBRS_ENTER save_reg=%r15
+	UNTRAIN_RET
 
-	/* EBX = 0 -> SWAPGS required on exit */
-	xorl	%ebx, %ebx
-	ret
+	RET
 SYM_CODE_END(paranoid_entry)
 
 /*
@@ -933,9 +961,19 @@
  *              1 -> no SWAPGS on exit
  *
  *     Y        User space GSBASE, must be restored unconditionally
+ *
+ * R14 - old CR3
+ * R15 - old SPEC_CTRL
  */
 SYM_CODE_START_LOCAL(paranoid_exit)
 	UNWIND_HINT_REGS
+
+	/*
+	 * Must restore IBRS state before both CR3 and %GS since we need access
+	 * to the per-CPU x86_spec_ctrl_shadow variable.
+	 */
+	IBRS_EXIT save_reg=%r15
+
 	/*
 	 * The order of operations is important. RESTORE_CR3 requires
 	 * kernel GSBASE.
@@ -964,13 +1002,14 @@
 SYM_CODE_END(paranoid_exit)
 
 /*
- * Save all registers in pt_regs, and switch GS if needed.
+ * Switch GS and CR3 if needed.
  */
 SYM_CODE_START_LOCAL(error_entry)
 	UNWIND_HINT_FUNC
-	cld
+
 	PUSH_AND_CLEAR_REGS save_ret=1
 	ENCODE_FRAME_POINTER 8
+
 	testb	$3, CS+8(%rsp)
 	jz	.Lerror_kernelspace
 
@@ -982,21 +1021,15 @@
 	FENCE_SWAPGS_USER_ENTRY
 	/* We have user CR3.  Change to kernel CR3. */
 	SWITCH_TO_KERNEL_CR3 scratch_reg=%rax
+	IBRS_ENTER
+	UNTRAIN_RET
 
+	leaq	8(%rsp), %rdi			/* arg0 = pt_regs pointer */
 .Lerror_entry_from_usermode_after_swapgs:
+
 	/* Put us onto the real thread stack. */
-	popq	%r12				/* save return addr in %12 */
-	movq	%rsp, %rdi			/* arg0 = pt_regs pointer */
 	call	sync_regs
-	movq	%rax, %rsp			/* switch stack */
-	ENCODE_FRAME_POINTER
-	pushq	%r12
-	ret
-
-.Lerror_entry_done_lfence:
-	FENCE_SWAPGS_KERNEL_ENTRY
-.Lerror_entry_done:
-	ret
+	RET
 
 	/*
 	 * There are two places in the kernel that can potentially fault with
@@ -1020,8 +1053,16 @@
 	 * .Lgs_change's error handler with kernel gsbase.
 	 */
 	SWAPGS
-	FENCE_SWAPGS_USER_ENTRY
-	jmp .Lerror_entry_done
+
+	/*
+	 * Issue an LFENCE to prevent GS speculation, regardless of whether it is a
+	 * kernel or user gsbase.
+	 */
+.Lerror_entry_done_lfence:
+	FENCE_SWAPGS_KERNEL_ENTRY
+	leaq	8(%rsp), %rax			/* return pt_regs pointer */
+	ANNOTATE_UNRET_END
+	RET
 
 .Lbstep_iret:
 	/* Fix truncated RIP */
@@ -1036,14 +1077,16 @@
 	SWAPGS
 	FENCE_SWAPGS_USER_ENTRY
 	SWITCH_TO_KERNEL_CR3 scratch_reg=%rax
+	IBRS_ENTER
+	UNTRAIN_RET
 
 	/*
 	 * Pretend that the exception came from user mode: set up pt_regs
 	 * as if we faulted immediately after IRET.
 	 */
-	mov	%rsp, %rdi
+	leaq	8(%rsp), %rdi			/* arg0 = pt_regs pointer */
 	call	fixup_bad_iret
-	mov	%rax, %rsp
+	mov	%rax, %rdi
 	jmp	.Lerror_entry_from_usermode_after_swapgs
 SYM_CODE_END(error_entry)
 
@@ -1105,6 +1148,7 @@
 	 */
 
 	ASM_CLAC
+	cld
 
 	/* Use %rdx as our temp variable throughout */
 	pushq	%rdx
@@ -1124,7 +1168,6 @@
 	 */
 
 	swapgs
-	cld
 	FENCE_SWAPGS_USER_ENTRY
 	SWITCH_TO_KERNEL_CR3 scratch_reg=%rdx
 	movq	%rsp, %rdx
@@ -1140,6 +1183,9 @@
 	PUSH_AND_CLEAR_REGS rdx=(%rdx)
 	ENCODE_FRAME_POINTER
 
+	IBRS_ENTER
+	UNTRAIN_RET
+
 	/*
 	 * At this point we no longer need to worry about stack damage
 	 * due to nesting -- we're on the normal thread stack and we're
@@ -1362,6 +1408,9 @@
 	movq	$-1, %rsi
 	call	exc_nmi
 
+	/* Always restore stashed SPEC_CTRL value (see paranoid_entry) */
+	IBRS_EXIT save_reg=%r15
+
 	/* Always restore stashed CR3 value (see paranoid_entry) */
 	RESTORE_CR3 scratch_reg=%r15 save_reg=%r14
 
@@ -1408,6 +1457,12 @@
 	movq	$0, 5*8(%rsp)		/* clear "NMI executing" */
 
 	/*
+	 * Skip CLEAR_CPU_BUFFERS here, since it only helps in rare cases like
+	 * NMI in kernel after user state is restored. For an unprivileged user
+	 * these conditions are hard to meet.
+	 */
+
+	/*
 	 * iretq reads the "iret" frame and exits the NMI stack in a
 	 * single instruction.  We are returning to kernel mode, so this
 	 * cannot result in a fault.  Similarly, we don't need to worry
@@ -1424,12 +1479,13 @@
 SYM_CODE_START(ignore_sysret)
 	UNWIND_HINT_EMPTY
 	mov	$-ENOSYS, %eax
+	CLEAR_CPU_BUFFERS
 	sysretl
 SYM_CODE_END(ignore_sysret)
 #endif
 
 .pushsection .text, "ax"
-SYM_CODE_START(rewind_stack_do_exit)
+SYM_CODE_START(rewind_stack_and_make_dead)
 	UNWIND_HINT_FUNC
 	/* Prevent any naive code from trying to unwind to our caller. */
 	xorl	%ebp, %ebp
@@ -1438,6 +1494,66 @@
 	leaq	-PTREGS_SIZE(%rax), %rsp
 	UNWIND_HINT_REGS
 
-	call	do_exit
-SYM_CODE_END(rewind_stack_do_exit)
+	call	make_task_dead
+SYM_CODE_END(rewind_stack_and_make_dead)
 .popsection
+
+/*
+ * This sequence executes branches in order to remove user branch information
+ * from the branch history tracker in the Branch Predictor, therefore removing
+ * user influence on subsequent BTB lookups.
+ *
+ * It should be used on parts prior to Alder Lake. Newer parts should use the
+ * BHI_DIS_S hardware control instead. If a pre-Alder Lake part is being
+ * virtualized on newer hardware the VMM should protect against BHI attacks by
+ * setting BHI_DIS_S for the guests.
+ *
+ * CALLs/RETs are necessary to prevent Loop Stream Detector(LSD) from engaging
+ * and not clearing the branch history. The call tree looks like:
+ *
+ * call 1
+ *    call 2
+ *      call 2
+ *        call 2
+ *          call 2
+ * 	      call 2
+ * 	      ret
+ * 	    ret
+ *        ret
+ *      ret
+ *    ret
+ * ret
+ *
+ * This means that the stack is non-constant and ORC can't unwind it with %rsp
+ * alone.  Therefore we unconditionally set up the frame pointer, which allows
+ * ORC to unwind properly.
+ *
+ * The alignment is for performance and not for safety, and may be safely
+ * refactored in the future if needed.
+ */
+SYM_FUNC_START(clear_bhb_loop)
+	push	%rbp
+	mov	%rsp, %rbp
+	movl	$5, %ecx
+	ANNOTATE_INTRA_FUNCTION_CALL
+	call	1f
+	jmp	5f
+	.align 64, 0xcc
+	ANNOTATE_INTRA_FUNCTION_CALL
+1:	call	2f
+	RET
+	.align 64, 0xcc
+2:	movl	$5, %eax
+3:	jmp	4f
+	nop
+4:	sub	$1, %eax
+	jnz	3b
+	sub	$1, %ecx
+	jnz	1b
+	RET
+5:	lfence
+	pop	%rbp
+	RET
+SYM_FUNC_END(clear_bhb_loop)
+EXPORT_SYMBOL_GPL(clear_bhb_loop)
+STACK_FRAME_NON_STANDARD(clear_bhb_loop)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/entry_64_compat.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/entry_64_compat.S
@@ -4,7 +4,6 @@
  *
  * Copyright 2000-2002 Andi Kleen, SuSE Labs.
  */
-#include "calling.h"
 #include <asm/asm-offsets.h>
 #include <asm/current.h>
 #include <asm/errno.h>
@@ -14,9 +13,12 @@
 #include <asm/irqflags.h>
 #include <asm/asm.h>
 #include <asm/smap.h>
+#include <asm/nospec-branch.h>
 #include <linux/linkage.h>
 #include <linux/err.h>
 
+#include "calling.h"
+
 	.section .entry.text, "ax"
 
 /*
@@ -47,7 +49,7 @@
  * 0(%ebp) arg6
  */
 SYM_CODE_START(entry_SYSENTER_compat)
-	UNWIND_HINT_EMPTY
+	UNWIND_HINT_ENTRY
 	/* Interrupts are off on entry. */
 	SWAPGS
 
@@ -135,6 +137,16 @@
 	jnz	.Lsysenter_fix_flags
 .Lsysenter_flags_fixed:
 
+	/*
+	 * CPU bugs mitigations mechanisms can call other functions. They
+	 * should be invoked after making sure TF is cleared because
+	 * single-step is ignored only for instructions inside the
+	 * entry_SYSENTER_compat function.
+	 */
+	IBRS_ENTER
+	UNTRAIN_RET
+	CLEAR_BRANCH_HISTORY
+
 	movq	%rsp, %rdi
 	call	do_SYSENTER_32
 	/* XEN PV guests always use IRET path */
@@ -197,7 +209,7 @@
  * 0(%esp) arg6
  */
 SYM_CODE_START(entry_SYSCALL_compat)
-	UNWIND_HINT_EMPTY
+	UNWIND_HINT_ENTRY
 	/* Interrupts are off on entry. */
 	swapgs
 
@@ -252,6 +264,10 @@
 
 	UNWIND_HINT_REGS
 
+	IBRS_ENTER
+	UNTRAIN_RET
+	CLEAR_BRANCH_HISTORY
+
 	movq	%rsp, %rdi
 	call	do_fast_syscall_32
 	/* XEN PV guests always use IRET path */
@@ -266,6 +282,8 @@
 	 */
 	STACKLEAK_ERASE
 
+	IBRS_EXIT
+
 	movq	RBX(%rsp), %rbx		/* pt_regs->rbx */
 	movq	RBP(%rsp), %rbp		/* pt_regs->rbp */
 	movq	EFLAGS(%rsp), %r11	/* pt_regs->flags (in r11) */
@@ -309,107 +327,20 @@
 	xorl	%r9d, %r9d
 	xorl	%r10d, %r10d
 	swapgs
+	CLEAR_CPU_BUFFERS
 	sysretl
 SYM_CODE_END(entry_SYSCALL_compat)
 
 /*
- * 32-bit legacy system call entry.
- *
- * 32-bit x86 Linux system calls traditionally used the INT $0x80
- * instruction.  INT $0x80 lands here.
- *
- * This entry point can be used by 32-bit and 64-bit programs to perform
- * 32-bit system calls.  Instances of INT $0x80 can be found inline in
- * various programs and libraries.  It is also used by the vDSO's
- * __kernel_vsyscall fallback for hardware that doesn't support a faster
- * entry method.  Restarted 32-bit system calls also fall back to INT
- * $0x80 regardless of what instruction was originally used to do the
- * system call.
- *
- * This is considered a slow path.  It is not used by most libc
- * implementations on modern hardware except during process startup.
- *
- * Arguments:
- * eax  system call number
- * ebx  arg1
- * ecx  arg2
- * edx  arg3
- * esi  arg4
- * edi  arg5
- * ebp  arg6
+ * int 0x80 is used by 32 bit mode as a system call entry. Normally idt entries
+ * point to C routines, however since this is a system call interface the branch
+ * history needs to be scrubbed to protect against BHI attacks, and that
+ * scrubbing needs to take place in assembly code prior to entering any C
+ * routines.
  */
-SYM_CODE_START(entry_INT80_compat)
-	UNWIND_HINT_EMPTY
-	/*
-	 * Interrupts are off on entry.
-	 */
-	ASM_CLAC			/* Do this early to minimize exposure */
-	SWAPGS
-
-	/*
-	 * User tracing code (ptrace or signal handlers) might assume that
-	 * the saved RAX contains a 32-bit number when we're invoking a 32-bit
-	 * syscall.  Just in case the high bits are nonzero, zero-extend
-	 * the syscall number.  (This could almost certainly be deleted
-	 * with no ill effects.)
-	 */
-	movl	%eax, %eax
-
-	/* switch to thread stack expects orig_ax and rdi to be pushed */
-	pushq	%rax			/* pt_regs->orig_ax */
-	pushq	%rdi			/* pt_regs->di */
-
-	/* Need to switch before accessing the thread stack. */
-	SWITCH_TO_KERNEL_CR3 scratch_reg=%rdi
-
-	/* In the Xen PV case we already run on the thread stack. */
-	ALTERNATIVE "", "jmp .Lint80_keep_stack", X86_FEATURE_XENPV
-
-	movq	%rsp, %rdi
-	movq	PER_CPU_VAR(cpu_current_top_of_stack), %rsp
-
-	pushq	6*8(%rdi)		/* regs->ss */
-	pushq	5*8(%rdi)		/* regs->rsp */
-	pushq	4*8(%rdi)		/* regs->eflags */
-	pushq	3*8(%rdi)		/* regs->cs */
-	pushq	2*8(%rdi)		/* regs->ip */
-	pushq	1*8(%rdi)		/* regs->orig_ax */
-	pushq	(%rdi)			/* pt_regs->di */
-.Lint80_keep_stack:
-
-	pushq	%rsi			/* pt_regs->si */
-	xorl	%esi, %esi		/* nospec   si */
-	pushq	%rdx			/* pt_regs->dx */
-	xorl	%edx, %edx		/* nospec   dx */
-	pushq	%rcx			/* pt_regs->cx */
-	xorl	%ecx, %ecx		/* nospec   cx */
-	pushq	$-ENOSYS		/* pt_regs->ax */
-	pushq   %r8			/* pt_regs->r8 */
-	xorl	%r8d, %r8d		/* nospec   r8 */
-	pushq   %r9			/* pt_regs->r9 */
-	xorl	%r9d, %r9d		/* nospec   r9 */
-	pushq   %r10			/* pt_regs->r10*/
-	xorl	%r10d, %r10d		/* nospec   r10 */
-	pushq   %r11			/* pt_regs->r11 */
-	xorl	%r11d, %r11d		/* nospec   r11 */
-	pushq   %rbx                    /* pt_regs->rbx */
-	xorl	%ebx, %ebx		/* nospec   rbx */
-	pushq   %rbp                    /* pt_regs->rbp */
-	xorl	%ebp, %ebp		/* nospec   rbp */
-	pushq   %r12                    /* pt_regs->r12 */
-	xorl	%r12d, %r12d		/* nospec   r12 */
-	pushq   %r13                    /* pt_regs->r13 */
-	xorl	%r13d, %r13d		/* nospec   r13 */
-	pushq   %r14                    /* pt_regs->r14 */
-	xorl	%r14d, %r14d		/* nospec   r14 */
-	pushq   %r15                    /* pt_regs->r15 */
-	xorl	%r15d, %r15d		/* nospec   r15 */
-
-	UNWIND_HINT_REGS
-
-	cld
-
-	movq	%rsp, %rdi
-	call	do_int80_syscall_32
-	jmp	swapgs_restore_regs_and_return_to_usermode
-SYM_CODE_END(entry_INT80_compat)
+SYM_CODE_START(int80_emulation)
+	ANNOTATE_NOENDBR
+	UNWIND_HINT_FUNC
+	CLEAR_BRANCH_HISTORY
+	jmp do_int80_emulation
+SYM_CODE_END(int80_emulation)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/syscall_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/syscall_32.c
@@ -18,8 +18,25 @@
 #include <asm/syscalls_32.h>
 #undef __SYSCALL
 
+/*
+ * The sys_call_table[] is no longer used for system calls, but
+ * kernel/trace/trace_syscalls.c still wants to know the system
+ * call address.
+ */
+#ifdef CONFIG_X86_32
 #define __SYSCALL(nr, sym) __ia32_##sym,
-
-__visible const sys_call_ptr_t ia32_sys_call_table[] = {
+const sys_call_ptr_t sys_call_table[] = {
 #include <asm/syscalls_32.h>
 };
+#undef __SYSCALL
+#endif
+
+#define __SYSCALL(nr, sym) case nr: return __ia32_##sym(regs);
+
+long ia32_sys_call(const struct pt_regs *regs, unsigned int nr)
+{
+	switch (nr) {
+	#include <asm/syscalls_32.h>
+	default: return __ia32_sys_ni_syscall(regs);
+	}
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/syscall_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/syscall_64.c
@@ -11,8 +11,23 @@
 #include <asm/syscalls_64.h>
 #undef __SYSCALL
 
+/*
+ * The sys_call_table[] is no longer used for system calls, but
+ * kernel/trace/trace_syscalls.c still wants to know the system
+ * call address.
+ */
 #define __SYSCALL(nr, sym) __x64_##sym,
-
-asmlinkage const sys_call_ptr_t sys_call_table[] = {
+const sys_call_ptr_t sys_call_table[] = {
 #include <asm/syscalls_64.h>
 };
+#undef __SYSCALL
+
+#define __SYSCALL(nr, sym) case nr: return __x64_##sym(regs);
+
+long x64_sys_call(const struct pt_regs *regs, unsigned int nr)
+{
+	switch (nr) {
+	#include <asm/syscalls_64.h>
+	default: return __x64_sys_ni_syscall(regs);
+	}
+};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/syscall_x32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/syscall_x32.c
@@ -11,8 +11,12 @@
 #include <asm/syscalls_x32.h>
 #undef __SYSCALL
 
-#define __SYSCALL(nr, sym) __x64_##sym,
+#define __SYSCALL(nr, sym) case nr: return __x64_##sym(regs);
 
-asmlinkage const sys_call_ptr_t x32_sys_call_table[] = {
-#include <asm/syscalls_x32.h>
+long x32_sys_call(const struct pt_regs *regs, unsigned int nr)
+{
+	switch (nr) {
+	#include <asm/syscalls_x32.h>
+	default: return __x64_sys_ni_syscall(regs);
+	}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/syscalls/syscall_32.tbl
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/syscalls/syscall_32.tbl
@@ -420,7 +420,7 @@
 412	i386	utimensat_time64	sys_utimensat
 413	i386	pselect6_time64		sys_pselect6			compat_sys_pselect6_time64
 414	i386	ppoll_time64		sys_ppoll			compat_sys_ppoll_time64
-416	i386	io_pgetevents_time64	sys_io_pgetevents
+416	i386	io_pgetevents_time64	sys_io_pgetevents		compat_sys_io_pgetevents_time64
 417	i386	recvmmsg_time64		sys_recvmmsg			compat_sys_recvmmsg_time64
 418	i386	mq_timedsend_time64	sys_mq_timedsend
 419	i386	mq_timedreceive_time64	sys_mq_timedreceive
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/thunk_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/thunk_32.S
@@ -24,15 +24,13 @@
 	popl %edx
 	popl %ecx
 	popl %eax
-	ret
+	RET
 	_ASM_NOKPROBE(\name)
 SYM_CODE_END(\name)
 	.endm
 
-#ifdef CONFIG_PREEMPTION
 	THUNK preempt_schedule_thunk, preempt_schedule
 	THUNK preempt_schedule_notrace_thunk, preempt_schedule_notrace
 	EXPORT_SYMBOL(preempt_schedule_thunk)
 	EXPORT_SYMBOL(preempt_schedule_notrace_thunk)
-#endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/thunk_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/thunk_64.S
@@ -31,14 +31,11 @@
 	_ASM_NOKPROBE(\name)
 	.endm
 
-#ifdef CONFIG_PREEMPTION
 	THUNK preempt_schedule_thunk, preempt_schedule
 	THUNK preempt_schedule_notrace_thunk, preempt_schedule_notrace
 	EXPORT_SYMBOL(preempt_schedule_thunk)
 	EXPORT_SYMBOL(preempt_schedule_notrace_thunk)
-#endif
 
-#ifdef CONFIG_PREEMPTION
 SYM_CODE_START_LOCAL_NOALIGN(__thunk_restore)
 	popq %r11
 	popq %r10
@@ -50,7 +47,6 @@
 	popq %rsi
 	popq %rdi
 	popq %rbp
-	ret
+	RET
 	_ASM_NOKPROBE(__thunk_restore)
 SYM_CODE_END(__thunk_restore)
-#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vdso/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vdso/Makefile
@@ -92,6 +92,7 @@
 endif
 
 $(vobjs): KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_LTO) $(GCC_PLUGINS_CFLAGS) $(RETPOLINE_CFLAGS),$(KBUILD_CFLAGS)) $(CFL)
+$(vobjs): KBUILD_AFLAGS += -DBUILD_VDSO
 
 #
 # vDSO code runs in userspace and -pg doesn't help with profiling anyway.
@@ -178,7 +179,7 @@
 		 sh $(srctree)/$(src)/checkundef.sh '$(NM)' '$@'
 
 VDSO_LDFLAGS = -shared --hash-style=both --build-id=sha1 \
-	$(call ld-option, --eh-frame-hdr) -Bsymbolic
+	$(call ld-option, --eh-frame-hdr) -Bsymbolic -z noexecstack
 GCOV_PROFILE := n
 
 quiet_cmd_vdso_and_check = VDSO    $@
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vdso/vdso.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vdso/vdso.lds.S
@@ -27,7 +27,9 @@
 		__vdso_time;
 		clock_getres;
 		__vdso_clock_getres;
+#ifdef CONFIG_X86_SGX
 		__vdso_sgx_enter_enclave;
+#endif
 	local: *;
 	};
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vdso/vdso32/system_call.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vdso/vdso32/system_call.S
@@ -78,7 +78,7 @@
 	popl	%ecx
 	CFI_RESTORE		ecx
 	CFI_ADJUST_CFA_OFFSET	-4
-	ret
+	RET
 	CFI_ENDPROC
 
 	.size __kernel_vsyscall,.-__kernel_vsyscall
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vdso/vma.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vdso/vma.c
@@ -322,8 +322,8 @@
 
 	/* Round the lowest possible end address up to a PMD boundary. */
 	end = (start + len + PMD_SIZE - 1) & PMD_MASK;
-	if (end >= TASK_SIZE_MAX)
-		end = TASK_SIZE_MAX;
+	if (end >= DEFAULT_MAP_WINDOW)
+		end = DEFAULT_MAP_WINDOW;
 	end -= len;
 
 	if (end > start) {
@@ -438,7 +438,7 @@
 static __init int vdso_setup(char *s)
 {
 	vdso64_enabled = simple_strtoul(s, NULL, 0);
-	return 0;
+	return 1;
 }
 __setup("vdso=", vdso_setup);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vdso/vsgx.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vdso/vsgx.S
@@ -81,7 +81,7 @@
 	pop	%rbx
 	leave
 	.cfi_def_cfa		%rsp, 8
-	ret
+	RET
 
 	/* The out-of-line code runs with the pre-leave stack frame. */
 	.cfi_def_cfa		%rbp, 16
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vsyscall/vsyscall_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vsyscall/vsyscall_64.c
@@ -98,11 +98,6 @@
 
 static bool write_ok_or_segv(unsigned long ptr, size_t size)
 {
-	/*
-	 * XXX: if access_ok, get_user, and put_user handled
-	 * sig_on_uaccess_err, this could go away.
-	 */
-
 	if (!access_ok((void __user *)ptr, size)) {
 		struct thread_struct *thread = &current->thread;
 
@@ -120,10 +115,8 @@
 bool emulate_vsyscall(unsigned long error_code,
 		      struct pt_regs *regs, unsigned long address)
 {
-	struct task_struct *tsk;
 	unsigned long caller;
 	int vsyscall_nr, syscall_nr, tmp;
-	int prev_sig_on_uaccess_err;
 	long ret;
 	unsigned long orig_dx;
 
@@ -172,8 +165,6 @@
 		goto sigsegv;
 	}
 
-	tsk = current;
-
 	/*
 	 * Check for access_ok violations and find the syscall nr.
 	 *
@@ -226,19 +217,16 @@
 	if ((!tmp && regs->orig_ax != syscall_nr) || regs->ip != address) {
 		warn_bad_vsyscall(KERN_DEBUG, regs,
 				  "seccomp tried to change syscall nr or ip");
-		do_exit(SIGSYS);
+		force_exit_sig(SIGSYS);
+		return true;
 	}
 	regs->orig_ax = -1;
 	if (tmp)
 		goto do_ret;  /* skip requested */
 
 	/*
-	 * With a real vsyscall, page faults cause SIGSEGV.  We want to
-	 * preserve that behavior to make writing exploits harder.
+	 * With a real vsyscall, page faults cause SIGSEGV.
 	 */
-	prev_sig_on_uaccess_err = current->thread.sig_on_uaccess_err;
-	current->thread.sig_on_uaccess_err = 1;
-
 	ret = -EFAULT;
 	switch (vsyscall_nr) {
 	case 0:
@@ -261,23 +249,12 @@
 		break;
 	}
 
-	current->thread.sig_on_uaccess_err = prev_sig_on_uaccess_err;
-
 check_fault:
 	if (ret == -EFAULT) {
 		/* Bad news -- userspace fed a bad pointer to a vsyscall. */
 		warn_bad_vsyscall(KERN_INFO, regs,
 				  "vsyscall fault (exploit attempt?)");
-
-		/*
-		 * If we failed to generate a signal for any reason,
-		 * generate one here.  (This should be impossible.)
-		 */
-		if (WARN_ON_ONCE(!sigismember(&tsk->pending.signal, SIGBUS) &&
-				 !sigismember(&tsk->pending.signal, SIGSEGV)))
-			goto sigsegv;
-
-		return true;  /* Don't emulate the ret. */
+		goto sigsegv;
 	}
 
 	regs->ax = ret;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/entry/vsyscall/vsyscall_emu_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/entry/vsyscall/vsyscall_emu_64.S
@@ -20,16 +20,19 @@
 	mov $__NR_gettimeofday, %rax
 	syscall
 	ret
+	int3
 
 	.balign 1024, 0xcc
 	mov $__NR_time, %rax
 	syscall
 	ret
+	int3
 
 	.balign 1024, 0xcc
 	mov $__NR_getcpu, %rax
 	syscall
 	ret
+	int3
 
 	.balign 4096, 0xcc
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
-obj-y					+= core.o probe.o
+obj-y					+= core.o probe.o utils.o
 obj-$(CONFIG_PERF_EVENTS_INTEL_RAPL)	+= rapl.o
 obj-y					+= amd/
 obj-$(CONFIG_X86_LOCAL_APIC)            += msr.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/amd/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/amd/core.c
@@ -364,7 +364,7 @@
 
 	/* pass precise event sampling to ibs: */
 	if (event->attr.precise_ip && get_ibs_caps())
-		return -ENOENT;
+		return forward_event_to_ibs(event);
 
 	if (has_branch_stack(event))
 		return -EOPNOTSUPP;
@@ -976,7 +976,7 @@
 		 * numbered counter following it.
 		 */
 		for (i = 0; i < x86_pmu.num_counters - 1; i += 2)
-			even_ctr_mask |= 1 << i;
+			even_ctr_mask |= BIT_ULL(i);
 
 		pair_constraint = (struct event_constraint)
 				    __EVENT_CONSTRAINT(0, even_ctr_mask, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/amd/ibs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/amd/ibs.c
@@ -194,7 +194,7 @@
 }
 
 /*
- * Use IBS for precise event sampling:
+ * core pmu config -> IBS config
  *
  *  perf record -a -e cpu-cycles:p ...    # use ibs op counting cycle count
  *  perf record -a -e r076:p ...          # same as -e cpu-cycles:p
@@ -203,25 +203,9 @@
  * IbsOpCntCtl (bit 19) of IBS Execution Control Register (IbsOpCtl,
  * MSRC001_1033) is used to select either cycle or micro-ops counting
  * mode.
- *
- * The rip of IBS samples has skid 0. Thus, IBS supports precise
- * levels 1 and 2 and the PERF_EFLAGS_EXACT is set. In rare cases the
- * rip is invalid when IBS was not able to record the rip correctly.
- * We clear PERF_EFLAGS_EXACT and take the rip from pt_regs then.
- *
  */
-static int perf_ibs_precise_event(struct perf_event *event, u64 *config)
+static int core_pmu_ibs_config(struct perf_event *event, u64 *config)
 {
-	switch (event->attr.precise_ip) {
-	case 0:
-		return -ENOENT;
-	case 1:
-	case 2:
-		break;
-	default:
-		return -EOPNOTSUPP;
-	}
-
 	switch (event->attr.type) {
 	case PERF_TYPE_HARDWARE:
 		switch (event->attr.config) {
@@ -247,22 +231,37 @@
 	return -EOPNOTSUPP;
 }
 
+/*
+ * The rip of IBS samples has skid 0. Thus, IBS supports precise
+ * levels 1 and 2 and the PERF_EFLAGS_EXACT is set. In rare cases the
+ * rip is invalid when IBS was not able to record the rip correctly.
+ * We clear PERF_EFLAGS_EXACT and take the rip from pt_regs then.
+ */
+int forward_event_to_ibs(struct perf_event *event)
+{
+	u64 config = 0;
+
+	if (!event->attr.precise_ip || event->attr.precise_ip > 2)
+		return -EOPNOTSUPP;
+
+	if (!core_pmu_ibs_config(event, &config)) {
+		event->attr.type = perf_ibs_op.pmu.type;
+		event->attr.config = config;
+	}
+	return -ENOENT;
+}
+
 static int perf_ibs_init(struct perf_event *event)
 {
 	struct hw_perf_event *hwc = &event->hw;
 	struct perf_ibs *perf_ibs;
 	u64 max_cnt, config;
-	int ret;
 
 	perf_ibs = get_ibs_pmu(event->attr.type);
-	if (perf_ibs) {
-		config = event->attr.config;
-	} else {
-		perf_ibs = &perf_ibs_op;
-		ret = perf_ibs_precise_event(event, &config);
-		if (ret)
-			return ret;
-	}
+	if (!perf_ibs)
+		return -ENOENT;
+
+	config = event->attr.config;
 
 	if (event->pmu != &perf_ibs->pmu)
 		return -ENOENT;
@@ -304,6 +303,16 @@
 	hwc->config_base = perf_ibs->msr;
 	hwc->config = config;
 
+	/*
+	 * rip recorded by IbsOpRip will not be consistent with rsp and rbp
+	 * recorded as part of interrupt regs. Thus we need to use rip from
+	 * interrupt regs while unwinding call stack. Setting _EARLY flag
+	 * makes sure we unwind call-stack before perf sample rip is set to
+	 * IbsOpRip.
+	 */
+	if (event->attr.sample_type & PERF_SAMPLE_CALLCHAIN)
+		event->attr.sample_type |= __PERF_SAMPLE_CALLCHAIN_EARLY;
+
 	return 0;
 }
 
@@ -687,6 +696,14 @@
 		data.raw = &raw;
 	}
 
+	/*
+	 * rip recorded by IbsOpRip will not be consistent with rsp and rbp
+	 * recorded as part of interrupt regs. Thus we need to use rip from
+	 * interrupt regs while unwinding call stack.
+	 */
+	if (event->attr.sample_type & PERF_SAMPLE_CALLCHAIN)
+		data.callchain = perf_callchain(event, iregs);
+
 	throttle = perf_event_overflow(event, &data, &regs);
 out:
 	if (throttle) {
@@ -759,9 +776,10 @@
 	return ret;
 }
 
-static __init void perf_event_ibs_init(void)
+static __init int perf_event_ibs_init(void)
 {
 	struct attribute **attr = ibs_op_format_attrs;
+	int ret;
 
 	/*
 	 * Some chips fail to reset the fetch count when it is written; instead
@@ -773,7 +791,9 @@
 	if (boot_cpu_data.x86 == 0x19 && boot_cpu_data.x86_model < 0x10)
 		perf_ibs_fetch.fetch_ignore_if_zero_rip = 1;
 
-	perf_ibs_pmu_init(&perf_ibs_fetch, "ibs_fetch");
+	ret = perf_ibs_pmu_init(&perf_ibs_fetch, "ibs_fetch");
+	if (ret)
+		return ret;
 
 	if (ibs_caps & IBS_CAPS_OPCNT) {
 		perf_ibs_op.config_mask |= IBS_OP_CNT_CTL;
@@ -786,15 +806,35 @@
 		perf_ibs_op.cnt_mask    |= IBS_OP_MAX_CNT_EXT_MASK;
 	}
 
-	perf_ibs_pmu_init(&perf_ibs_op, "ibs_op");
+	ret = perf_ibs_pmu_init(&perf_ibs_op, "ibs_op");
+	if (ret)
+		goto err_op;
+
+	ret = register_nmi_handler(NMI_LOCAL, perf_ibs_nmi_handler, 0, "perf_ibs");
+	if (ret)
+		goto err_nmi;
 
-	register_nmi_handler(NMI_LOCAL, perf_ibs_nmi_handler, 0, "perf_ibs");
 	pr_info("perf: AMD IBS detected (0x%08x)\n", ibs_caps);
+	return 0;
+
+err_nmi:
+	perf_pmu_unregister(&perf_ibs_op.pmu);
+	free_percpu(perf_ibs_op.pcpu);
+	perf_ibs_op.pcpu = NULL;
+err_op:
+	perf_pmu_unregister(&perf_ibs_fetch.pmu);
+	free_percpu(perf_ibs_fetch.pcpu);
+	perf_ibs_fetch.pcpu = NULL;
+
+	return ret;
 }
 
 #else /* defined(CONFIG_PERF_EVENTS) && defined(CONFIG_CPU_SUP_AMD) */
 
-static __init void perf_event_ibs_init(void) { }
+static __init int perf_event_ibs_init(void)
+{
+	return 0;
+}
 
 #endif
 
@@ -1064,9 +1104,7 @@
 			  x86_pmu_amd_ibs_starting_cpu,
 			  x86_pmu_amd_ibs_dying_cpu);
 
-	perf_event_ibs_init();
-
-	return 0;
+	return perf_event_ibs_init();
 }
 
 /* Since we need the pci subsystem to init ibs we can't do this earlier: */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/core.c
@@ -1649,6 +1649,7 @@
 	while (++i < cpuc->n_events) {
 		cpuc->event_list[i-1] = cpuc->event_list[i];
 		cpuc->event_constraint[i-1] = cpuc->event_constraint[i];
+		cpuc->assign[i-1] = cpuc->assign[i];
 	}
 	cpuc->event_constraint[i-1] = NULL;
 	--cpuc->n_events;
@@ -2762,10 +2763,11 @@
 void
 perf_callchain_kernel(struct perf_callchain_entry_ctx *entry, struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct unwind_state state;
 	unsigned long addr;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* TODO: We don't support guest os callchain now */
 		return;
 	}
@@ -2865,10 +2867,11 @@
 void
 perf_callchain_user(struct perf_callchain_entry_ctx *entry, struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	struct stack_frame frame;
 	const struct stack_frame __user *fp;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (guest_cbs && guest_cbs->is_in_guest()) {
 		/* TODO: We don't support guest os callchain now */
 		return;
 	}
@@ -2945,18 +2948,21 @@
 
 unsigned long perf_instruction_pointer(struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
-		return perf_guest_cbs->get_guest_ip();
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
+
+	if (guest_cbs && guest_cbs->is_in_guest())
+		return guest_cbs->get_guest_ip();
 
 	return regs->ip + code_segment_base(regs);
 }
 
 unsigned long perf_misc_flags(struct pt_regs *regs)
 {
+	struct perf_guest_info_callbacks *guest_cbs = perf_get_guest_cbs();
 	int misc = 0;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		if (perf_guest_cbs->is_user_mode())
+	if (guest_cbs && guest_cbs->is_in_guest()) {
+		if (guest_cbs->is_user_mode())
 			misc |= PERF_RECORD_MISC_GUEST_USER;
 		else
 			misc |= PERF_RECORD_MISC_GUEST_KERNEL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/core.c
@@ -243,7 +243,8 @@
 
 static struct event_constraint intel_icl_event_constraints[] = {
 	FIXED_EVENT_CONSTRAINT(0x00c0, 0),	/* INST_RETIRED.ANY */
-	FIXED_EVENT_CONSTRAINT(0x01c0, 0),	/* INST_RETIRED.PREC_DIST */
+	FIXED_EVENT_CONSTRAINT(0x01c0, 0),	/* old INST_RETIRED.PREC_DIST */
+	FIXED_EVENT_CONSTRAINT(0x0100, 0),	/* INST_RETIRED.PREC_DIST */
 	FIXED_EVENT_CONSTRAINT(0x003c, 1),	/* CPU_CLK_UNHALTED.CORE */
 	FIXED_EVENT_CONSTRAINT(0x0300, 2),	/* CPU_CLK_UNHALTED.REF */
 	FIXED_EVENT_CONSTRAINT(0x0400, 3),	/* SLOTS */
@@ -254,7 +255,7 @@
 	INTEL_EVENT_CONSTRAINT_RANGE(0x03, 0x0a, 0xf),
 	INTEL_EVENT_CONSTRAINT_RANGE(0x1f, 0x28, 0xf),
 	INTEL_EVENT_CONSTRAINT(0x32, 0xf),	/* SW_PREFETCH_ACCESS.* */
-	INTEL_EVENT_CONSTRAINT_RANGE(0x48, 0x54, 0xf),
+	INTEL_EVENT_CONSTRAINT_RANGE(0x48, 0x56, 0xf),
 	INTEL_EVENT_CONSTRAINT_RANGE(0x60, 0x8b, 0xf),
 	INTEL_UEVENT_CONSTRAINT(0x04a3, 0xff),  /* CYCLE_ACTIVITY.STALLS_TOTAL */
 	INTEL_UEVENT_CONSTRAINT(0x10a3, 0xff),  /* CYCLE_ACTIVITY.CYCLES_MEM_ANY */
@@ -280,7 +281,7 @@
 	INTEL_UEVENT_EXTRA_REG(0x012a, MSR_OFFCORE_RSP_0, 0x3fffffffffull, RSP_0),
 	INTEL_UEVENT_EXTRA_REG(0x012b, MSR_OFFCORE_RSP_1, 0x3fffffffffull, RSP_1),
 	INTEL_UEVENT_PEBS_LDLAT_EXTRA_REG(0x01cd),
-	INTEL_UEVENT_EXTRA_REG(0x01c6, MSR_PEBS_FRONTEND, 0x7fff17, FE),
+	INTEL_UEVENT_EXTRA_REG(0x01c6, MSR_PEBS_FRONTEND, 0x7fff1f, FE),
 	INTEL_UEVENT_EXTRA_REG(0x40ad, MSR_PEBS_FRONTEND, 0x7, FE),
 	INTEL_UEVENT_EXTRA_REG(0x04c2, MSR_PEBS_FRONTEND, 0x8, FE),
 	EVENT_EXTRA_END
@@ -288,7 +289,7 @@
 
 static struct event_constraint intel_spr_event_constraints[] = {
 	FIXED_EVENT_CONSTRAINT(0x00c0, 0),	/* INST_RETIRED.ANY */
-	FIXED_EVENT_CONSTRAINT(0x01c0, 0),	/* INST_RETIRED.PREC_DIST */
+	FIXED_EVENT_CONSTRAINT(0x0100, 0),	/* INST_RETIRED.PREC_DIST */
 	FIXED_EVENT_CONSTRAINT(0x003c, 1),	/* CPU_CLK_UNHALTED.CORE */
 	FIXED_EVENT_CONSTRAINT(0x0300, 2),	/* CPU_CLK_UNHALTED.REF */
 	FIXED_EVENT_CONSTRAINT(0x0400, 3),	/* SLOTS */
@@ -2787,6 +2788,7 @@
 {
 	struct perf_sample_data data;
 	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	struct perf_guest_info_callbacks *guest_cbs;
 	int bit;
 	int handled = 0;
 	u64 intel_ctrl = hybrid(cpuc->pmu, intel_ctrl);
@@ -2853,9 +2855,11 @@
 	 */
 	if (__test_and_clear_bit(GLOBAL_STATUS_TRACE_TOPAPMI_BIT, (unsigned long *)&status)) {
 		handled++;
-		if (unlikely(perf_guest_cbs && perf_guest_cbs->is_in_guest() &&
-			perf_guest_cbs->handle_intel_pt_intr))
-			perf_guest_cbs->handle_intel_pt_intr();
+
+		guest_cbs = perf_get_guest_cbs();
+		if (unlikely(guest_cbs && guest_cbs->is_in_guest() &&
+			     guest_cbs->handle_intel_pt_intr))
+			guest_cbs->handle_intel_pt_intr();
 		else
 			intel_pt_interrupt();
 	}
@@ -2998,8 +3002,10 @@
 {
 	struct event_constraint *c = &vlbr_constraint;
 
-	if (unlikely(constraint_match(c, event->hw.config)))
+	if (unlikely(constraint_match(c, event->hw.config))) {
+		event->hw.flags |= c->flags;
 		return c;
+	}
 
 	return NULL;
 }
@@ -4358,8 +4364,11 @@
 
 	init_debug_store_on_cpu(cpu);
 	/*
-	 * Deal with CPUs that don't clear their LBRs on power-up.
+	 * Deal with CPUs that don't clear their LBRs on power-up, and that may
+	 * even boot with LBRs enabled.
 	 */
+	if (!static_cpu_has(X86_FEATURE_ARCH_LBR) && x86_pmu.lbr_nr)
+		msr_clear_bit(MSR_IA32_DEBUGCTLMSR, DEBUGCTLMSR_LBR_BIT);
 	intel_pmu_lbr_reset();
 
 	cpuc->lbr_sel = NULL;
@@ -4648,6 +4657,19 @@
 	.lbr_read		= intel_pmu_lbr_read_64,
 	.lbr_save		= intel_pmu_lbr_save,
 	.lbr_restore		= intel_pmu_lbr_restore,
+
+	/*
+	 * SMM has access to all 4 rings and while traditionally SMM code only
+	 * ran in CPL0, 2021-era firmware is starting to make use of CPL3 in SMM.
+	 *
+	 * Since the EVENTSEL.{USR,OS} CPL filtering makes no distinction
+	 * between SMM or not, this results in what should be pure userspace
+	 * counters including SMM data.
+	 *
+	 * This is a clear privilege issue, therefore globally disable
+	 * counting SMM by default.
+	 */
+	.attr_freeze_on_smi	= 1,
 };
 
 static __init void intel_clovertown_quirk(void)
@@ -4694,6 +4716,7 @@
 	INTEL_CPU_DESC(INTEL_FAM6_SKYLAKE_X,		 5, 0x00000000),
 	INTEL_CPU_DESC(INTEL_FAM6_SKYLAKE_X,		 6, 0x00000000),
 	INTEL_CPU_DESC(INTEL_FAM6_SKYLAKE_X,		 7, 0x00000000),
+	INTEL_CPU_DESC(INTEL_FAM6_SKYLAKE_X,		11, 0x00000000),
 	INTEL_CPU_DESC(INTEL_FAM6_SKYLAKE_L,		 3, 0x0000007c),
 	INTEL_CPU_DESC(INTEL_FAM6_SKYLAKE,		 3, 0x0000007c),
 	INTEL_CPU_DESC(INTEL_FAM6_KABYLAKE,		 9, 0x0000004e),
@@ -5447,7 +5470,11 @@
 			/* Disabled fixed counters which are not in CPUID */
 			c->idxmsk64 &= intel_ctrl;
 
-			if (c->idxmsk64 != INTEL_PMC_MSK_FIXED_REF_CYCLES)
+			/*
+			 * Don't extend the pseudo-encoding to the
+			 * generic counters
+			 */
+			if (!use_fixed_pseudo_encoding(c->code))
 				c->idxmsk64 |= (1ULL << num_counters) - 1;
 		}
 		c->idxmsk64 &=
@@ -6085,6 +6112,7 @@
 		break;
 
 	case INTEL_FAM6_SAPPHIRERAPIDS_X:
+	case INTEL_FAM6_EMERALDRAPIDS_X:
 		pmem = true;
 		x86_pmu.late_ack = true;
 		memcpy(hw_cache_event_ids, spr_hw_cache_event_ids, sizeof(hw_cache_event_ids));
@@ -6181,6 +6209,19 @@
 			pmu->num_counters = x86_pmu.num_counters;
 			pmu->num_counters_fixed = x86_pmu.num_counters_fixed;
 		}
+
+		/*
+		 * Quirk: For some Alder Lake machine, when all E-cores are disabled in
+		 * a BIOS, the leaf 0xA will enumerate all counters of P-cores. However,
+		 * the X86_FEATURE_HYBRID_CPU is still set. The above codes will
+		 * mistakenly add extra counters for P-cores. Correct the number of
+		 * counters here.
+		 */
+		if ((pmu->num_counters > 8) || (pmu->num_counters_fixed > 4)) {
+			pmu->num_counters = x86_pmu.num_counters;
+			pmu->num_counters_fixed = x86_pmu.num_counters_fixed;
+		}
+
 		pmu->max_pebs_events = min_t(unsigned, MAX_PEBS_EVENTS, pmu->num_counters);
 		pmu->unconstrained = (struct event_constraint)
 					__EVENT_CONSTRAINT(0, (1ULL << pmu->num_counters) - 1,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/cstate.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/cstate.c
@@ -674,6 +674,7 @@
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE,		&icl_cstates),
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X,		&icx_cstates),
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_D,		&icx_cstates),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X,	&icx_cstates),
 
 	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE_L,		&icl_cstates),
 	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE,		&icl_cstates),
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/ds.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/ds.c
@@ -236,6 +236,7 @@
 static u64 store_latency_data(u64 status)
 {
 	union intel_x86_pebs_dse dse;
+	union perf_mem_data_src src;
 	u64 val;
 
 	dse.val = status;
@@ -263,7 +264,14 @@
 
 	val |= P(BLK, NA);
 
-	return val;
+	/*
+	 * the pebs_data_source table is only for loads
+	 * so override the mem_op to say STORE instead
+	 */
+	src.val = val;
+	src.mem_op = P(OP,STORE);
+
+	return src.val;
 }
 
 struct pebs_record_core {
@@ -923,12 +931,18 @@
 };
 
 struct event_constraint intel_icl_pebs_event_constraints[] = {
-	INTEL_FLAGS_UEVENT_CONSTRAINT(0x1c0, 0x100000000ULL),	/* INST_RETIRED.PREC_DIST */
+	INTEL_FLAGS_UEVENT_CONSTRAINT(0x01c0, 0x100000000ULL),	/* old INST_RETIRED.PREC_DIST */
+	INTEL_FLAGS_UEVENT_CONSTRAINT(0x0100, 0x100000000ULL),	/* INST_RETIRED.PREC_DIST */
 	INTEL_FLAGS_UEVENT_CONSTRAINT(0x0400, 0x800000000ULL),	/* SLOTS */
 
 	INTEL_PLD_CONSTRAINT(0x1cd, 0xff),			/* MEM_TRANS_RETIRED.LOAD_LATENCY */
-	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x1d0, 0xf),	/* MEM_INST_RETIRED.LOAD */
-	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x2d0, 0xf),	/* MEM_INST_RETIRED.STORE */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x11d0, 0xf),	/* MEM_INST_RETIRED.STLB_MISS_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x12d0, 0xf),	/* MEM_INST_RETIRED.STLB_MISS_STORES */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x21d0, 0xf),	/* MEM_INST_RETIRED.LOCK_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x41d0, 0xf),	/* MEM_INST_RETIRED.SPLIT_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x42d0, 0xf),	/* MEM_INST_RETIRED.SPLIT_STORES */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x81d0, 0xf),	/* MEM_INST_RETIRED.ALL_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x82d0, 0xf),	/* MEM_INST_RETIRED.ALL_STORES */
 
 	INTEL_FLAGS_EVENT_CONSTRAINT_DATALA_LD_RANGE(0xd1, 0xd4, 0xf), /* MEM_LOAD_*_RETIRED.* */
 
@@ -943,14 +957,19 @@
 };
 
 struct event_constraint intel_spr_pebs_event_constraints[] = {
-	INTEL_FLAGS_UEVENT_CONSTRAINT(0x1c0, 0x100000000ULL),
+	INTEL_FLAGS_UEVENT_CONSTRAINT(0x100, 0x100000000ULL),	/* INST_RETIRED.PREC_DIST */
 	INTEL_FLAGS_UEVENT_CONSTRAINT(0x0400, 0x800000000ULL),
 
 	INTEL_FLAGS_EVENT_CONSTRAINT(0xc0, 0xfe),
 	INTEL_PLD_CONSTRAINT(0x1cd, 0xfe),
 	INTEL_PSD_CONSTRAINT(0x2cd, 0x1),
-	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x1d0, 0xf),
-	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x2d0, 0xf),
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x11d0, 0xf),	/* MEM_INST_RETIRED.STLB_MISS_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x12d0, 0xf),	/* MEM_INST_RETIRED.STLB_MISS_STORES */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x21d0, 0xf),	/* MEM_INST_RETIRED.LOCK_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x41d0, 0xf),	/* MEM_INST_RETIRED.SPLIT_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x42d0, 0xf),	/* MEM_INST_RETIRED.SPLIT_STORES */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_LD(0x81d0, 0xf),	/* MEM_INST_RETIRED.ALL_LOADS */
+	INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_ST(0x82d0, 0xf),	/* MEM_INST_RETIRED.ALL_STORES */
 
 	INTEL_FLAGS_EVENT_CONSTRAINT_DATALA_LD_RANGE(0xd1, 0xd4, 0xf),
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/lbr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/lbr.c
@@ -4,7 +4,6 @@
 
 #include <asm/perf_event.h>
 #include <asm/msr.h>
-#include <asm/insn.h>
 
 #include "../perf_event.h"
 
@@ -74,65 +73,6 @@
 #define LBR_FROM_SIGNEXT_2MSB	(BIT_ULL(60) | BIT_ULL(59))
 
 /*
- * x86control flow change classification
- * x86control flow changes include branches, interrupts, traps, faults
- */
-enum {
-	X86_BR_NONE		= 0,      /* unknown */
-
-	X86_BR_USER		= 1 << 0, /* branch target is user */
-	X86_BR_KERNEL		= 1 << 1, /* branch target is kernel */
-
-	X86_BR_CALL		= 1 << 2, /* call */
-	X86_BR_RET		= 1 << 3, /* return */
-	X86_BR_SYSCALL		= 1 << 4, /* syscall */
-	X86_BR_SYSRET		= 1 << 5, /* syscall return */
-	X86_BR_INT		= 1 << 6, /* sw interrupt */
-	X86_BR_IRET		= 1 << 7, /* return from interrupt */
-	X86_BR_JCC		= 1 << 8, /* conditional */
-	X86_BR_JMP		= 1 << 9, /* jump */
-	X86_BR_IRQ		= 1 << 10,/* hw interrupt or trap or fault */
-	X86_BR_IND_CALL		= 1 << 11,/* indirect calls */
-	X86_BR_ABORT		= 1 << 12,/* transaction abort */
-	X86_BR_IN_TX		= 1 << 13,/* in transaction */
-	X86_BR_NO_TX		= 1 << 14,/* not in transaction */
-	X86_BR_ZERO_CALL	= 1 << 15,/* zero length call */
-	X86_BR_CALL_STACK	= 1 << 16,/* call stack */
-	X86_BR_IND_JMP		= 1 << 17,/* indirect jump */
-
-	X86_BR_TYPE_SAVE	= 1 << 18,/* indicate to save branch type */
-
-};
-
-#define X86_BR_PLM (X86_BR_USER | X86_BR_KERNEL)
-#define X86_BR_ANYTX (X86_BR_NO_TX | X86_BR_IN_TX)
-
-#define X86_BR_ANY       \
-	(X86_BR_CALL    |\
-	 X86_BR_RET     |\
-	 X86_BR_SYSCALL |\
-	 X86_BR_SYSRET  |\
-	 X86_BR_INT     |\
-	 X86_BR_IRET    |\
-	 X86_BR_JCC     |\
-	 X86_BR_JMP	 |\
-	 X86_BR_IRQ	 |\
-	 X86_BR_ABORT	 |\
-	 X86_BR_IND_CALL |\
-	 X86_BR_IND_JMP  |\
-	 X86_BR_ZERO_CALL)
-
-#define X86_BR_ALL (X86_BR_PLM | X86_BR_ANY)
-
-#define X86_BR_ANY_CALL		 \
-	(X86_BR_CALL		|\
-	 X86_BR_IND_CALL	|\
-	 X86_BR_ZERO_CALL	|\
-	 X86_BR_SYSCALL		|\
-	 X86_BR_IRQ		|\
-	 X86_BR_INT)
-
-/*
  * Intel LBR_CTL bits
  *
  * Hardware branch filter for Arch LBR
@@ -1114,6 +1054,14 @@
 
 	if (static_cpu_has(X86_FEATURE_ARCH_LBR)) {
 		reg->config = mask;
+
+		/*
+		 * The Arch LBR HW can retrieve the common branch types
+		 * from the LBR_INFO. It doesn't require the high overhead
+		 * SW disassemble.
+		 * Enable the branch type by default for the Arch LBR.
+		 */
+		reg->reg |= X86_BR_TYPE_SAVE;
 		return 0;
 	}
 
@@ -1160,219 +1108,6 @@
 	return ret;
 }
 
-/*
- * return the type of control flow change at address "from"
- * instruction is not necessarily a branch (in case of interrupt).
- *
- * The branch type returned also includes the priv level of the
- * target of the control flow change (X86_BR_USER, X86_BR_KERNEL).
- *
- * If a branch type is unknown OR the instruction cannot be
- * decoded (e.g., text page not present), then X86_BR_NONE is
- * returned.
- */
-static int branch_type(unsigned long from, unsigned long to, int abort)
-{
-	struct insn insn;
-	void *addr;
-	int bytes_read, bytes_left;
-	int ret = X86_BR_NONE;
-	int ext, to_plm, from_plm;
-	u8 buf[MAX_INSN_SIZE];
-	int is64 = 0;
-
-	to_plm = kernel_ip(to) ? X86_BR_KERNEL : X86_BR_USER;
-	from_plm = kernel_ip(from) ? X86_BR_KERNEL : X86_BR_USER;
-
-	/*
-	 * maybe zero if lbr did not fill up after a reset by the time
-	 * we get a PMU interrupt
-	 */
-	if (from == 0 || to == 0)
-		return X86_BR_NONE;
-
-	if (abort)
-		return X86_BR_ABORT | to_plm;
-
-	if (from_plm == X86_BR_USER) {
-		/*
-		 * can happen if measuring at the user level only
-		 * and we interrupt in a kernel thread, e.g., idle.
-		 */
-		if (!current->mm)
-			return X86_BR_NONE;
-
-		/* may fail if text not present */
-		bytes_left = copy_from_user_nmi(buf, (void __user *)from,
-						MAX_INSN_SIZE);
-		bytes_read = MAX_INSN_SIZE - bytes_left;
-		if (!bytes_read)
-			return X86_BR_NONE;
-
-		addr = buf;
-	} else {
-		/*
-		 * The LBR logs any address in the IP, even if the IP just
-		 * faulted. This means userspace can control the from address.
-		 * Ensure we don't blindly read any address by validating it is
-		 * a known text address.
-		 */
-		if (kernel_text_address(from)) {
-			addr = (void *)from;
-			/*
-			 * Assume we can get the maximum possible size
-			 * when grabbing kernel data.  This is not
-			 * _strictly_ true since we could possibly be
-			 * executing up next to a memory hole, but
-			 * it is very unlikely to be a problem.
-			 */
-			bytes_read = MAX_INSN_SIZE;
-		} else {
-			return X86_BR_NONE;
-		}
-	}
-
-	/*
-	 * decoder needs to know the ABI especially
-	 * on 64-bit systems running 32-bit apps
-	 */
-#ifdef CONFIG_X86_64
-	is64 = kernel_ip((unsigned long)addr) || any_64bit_mode(current_pt_regs());
-#endif
-	insn_init(&insn, addr, bytes_read, is64);
-	if (insn_get_opcode(&insn))
-		return X86_BR_ABORT;
-
-	switch (insn.opcode.bytes[0]) {
-	case 0xf:
-		switch (insn.opcode.bytes[1]) {
-		case 0x05: /* syscall */
-		case 0x34: /* sysenter */
-			ret = X86_BR_SYSCALL;
-			break;
-		case 0x07: /* sysret */
-		case 0x35: /* sysexit */
-			ret = X86_BR_SYSRET;
-			break;
-		case 0x80 ... 0x8f: /* conditional */
-			ret = X86_BR_JCC;
-			break;
-		default:
-			ret = X86_BR_NONE;
-		}
-		break;
-	case 0x70 ... 0x7f: /* conditional */
-		ret = X86_BR_JCC;
-		break;
-	case 0xc2: /* near ret */
-	case 0xc3: /* near ret */
-	case 0xca: /* far ret */
-	case 0xcb: /* far ret */
-		ret = X86_BR_RET;
-		break;
-	case 0xcf: /* iret */
-		ret = X86_BR_IRET;
-		break;
-	case 0xcc ... 0xce: /* int */
-		ret = X86_BR_INT;
-		break;
-	case 0xe8: /* call near rel */
-		if (insn_get_immediate(&insn) || insn.immediate1.value == 0) {
-			/* zero length call */
-			ret = X86_BR_ZERO_CALL;
-			break;
-		}
-		fallthrough;
-	case 0x9a: /* call far absolute */
-		ret = X86_BR_CALL;
-		break;
-	case 0xe0 ... 0xe3: /* loop jmp */
-		ret = X86_BR_JCC;
-		break;
-	case 0xe9 ... 0xeb: /* jmp */
-		ret = X86_BR_JMP;
-		break;
-	case 0xff: /* call near absolute, call far absolute ind */
-		if (insn_get_modrm(&insn))
-			return X86_BR_ABORT;
-
-		ext = (insn.modrm.bytes[0] >> 3) & 0x7;
-		switch (ext) {
-		case 2: /* near ind call */
-		case 3: /* far ind call */
-			ret = X86_BR_IND_CALL;
-			break;
-		case 4:
-		case 5:
-			ret = X86_BR_IND_JMP;
-			break;
-		}
-		break;
-	default:
-		ret = X86_BR_NONE;
-	}
-	/*
-	 * interrupts, traps, faults (and thus ring transition) may
-	 * occur on any instructions. Thus, to classify them correctly,
-	 * we need to first look at the from and to priv levels. If they
-	 * are different and to is in the kernel, then it indicates
-	 * a ring transition. If the from instruction is not a ring
-	 * transition instr (syscall, systenter, int), then it means
-	 * it was a irq, trap or fault.
-	 *
-	 * we have no way of detecting kernel to kernel faults.
-	 */
-	if (from_plm == X86_BR_USER && to_plm == X86_BR_KERNEL
-	    && ret != X86_BR_SYSCALL && ret != X86_BR_INT)
-		ret = X86_BR_IRQ;
-
-	/*
-	 * branch priv level determined by target as
-	 * is done by HW when LBR_SELECT is implemented
-	 */
-	if (ret != X86_BR_NONE)
-		ret |= to_plm;
-
-	return ret;
-}
-
-#define X86_BR_TYPE_MAP_MAX	16
-
-static int branch_map[X86_BR_TYPE_MAP_MAX] = {
-	PERF_BR_CALL,		/* X86_BR_CALL */
-	PERF_BR_RET,		/* X86_BR_RET */
-	PERF_BR_SYSCALL,	/* X86_BR_SYSCALL */
-	PERF_BR_SYSRET,		/* X86_BR_SYSRET */
-	PERF_BR_UNKNOWN,	/* X86_BR_INT */
-	PERF_BR_UNKNOWN,	/* X86_BR_IRET */
-	PERF_BR_COND,		/* X86_BR_JCC */
-	PERF_BR_UNCOND,		/* X86_BR_JMP */
-	PERF_BR_UNKNOWN,	/* X86_BR_IRQ */
-	PERF_BR_IND_CALL,	/* X86_BR_IND_CALL */
-	PERF_BR_UNKNOWN,	/* X86_BR_ABORT */
-	PERF_BR_UNKNOWN,	/* X86_BR_IN_TX */
-	PERF_BR_UNKNOWN,	/* X86_BR_NO_TX */
-	PERF_BR_CALL,		/* X86_BR_ZERO_CALL */
-	PERF_BR_UNKNOWN,	/* X86_BR_CALL_STACK */
-	PERF_BR_IND,		/* X86_BR_IND_JMP */
-};
-
-static int
-common_branch_type(int type)
-{
-	int i;
-
-	type >>= 2; /* skip X86_BR_USER and X86_BR_KERNEL */
-
-	if (type) {
-		i = __ffs(type);
-		if (i < X86_BR_TYPE_MAP_MAX)
-			return branch_map[i];
-	}
-
-	return PERF_BR_UNKNOWN;
-}
-
 enum {
 	ARCH_LBR_BR_TYPE_JCC			= 0,
 	ARCH_LBR_BR_TYPE_NEAR_IND_JMP		= 1,
@@ -1734,6 +1469,9 @@
 	 * Check the LBR state with the corresponding software structure.
 	 * Disable LBR XSAVES support if the size doesn't match.
 	 */
+	if (xfeature_size(XFEATURE_LBR) == 0)
+		return false;
+
 	if (WARN_ON(xfeature_size(XFEATURE_LBR) != get_lbr_state_size()))
 		return false;
 
@@ -1836,7 +1574,7 @@
 	return;
 
 clear_arch_lbr:
-	clear_cpu_cap(&boot_cpu_data, X86_FEATURE_ARCH_LBR);
+	setup_clear_cpu_cap(X86_FEATURE_ARCH_LBR);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/pt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/pt.c
@@ -13,6 +13,8 @@
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
 #include <linux/types.h>
+#include <linux/bits.h>
+#include <linux/limits.h>
 #include <linux/slab.h>
 #include <linux/device.h>
 
@@ -472,7 +474,7 @@
 			pt->filters.filter[range].msr_b = filter->msr_b;
 		}
 
-		rtit_ctl |= filter->config << pt_address_ranges[range].reg_off;
+		rtit_ctl |= (u64)filter->config << pt_address_ranges[range].reg_off;
 	}
 
 	return rtit_ctl;
@@ -809,11 +811,13 @@
 	buf->cur_idx++;
 
 	if (buf->cur_idx == buf->cur->last) {
-		if (buf->cur == buf->last)
+		if (buf->cur == buf->last) {
 			buf->cur = buf->first;
-		else
+			buf->wrapped = true;
+		} else {
 			buf->cur = list_entry(buf->cur->list.next, struct topa,
 					      list);
+		}
 		buf->cur_idx = 0;
 	}
 }
@@ -827,8 +831,11 @@
 static void pt_update_head(struct pt *pt)
 {
 	struct pt_buffer *buf = perf_get_aux(&pt->handle);
+	bool wrapped = buf->wrapped;
 	u64 topa_idx, base, old;
 
+	buf->wrapped = false;
+
 	if (buf->single) {
 		local_set(&buf->data_size, buf->output_off);
 		return;
@@ -846,7 +853,7 @@
 	} else {
 		old = (local64_xchg(&buf->head, base) &
 		       ((buf->nr_pages << PAGE_SHIFT) - 1));
-		if (base < old)
+		if (base < old || (base == old && wrapped))
 			base += buf->nr_pages << PAGE_SHIFT;
 
 		local_add(base - old, &buf->data_size);
@@ -859,7 +866,7 @@
  */
 static void *pt_buffer_region(struct pt_buffer *buf)
 {
-	return phys_to_virt(TOPA_ENTRY(buf->cur, buf->cur_idx)->base << TOPA_SHIFT);
+	return phys_to_virt((phys_addr_t)TOPA_ENTRY(buf->cur, buf->cur_idx)->base << TOPA_SHIFT);
 }
 
 /**
@@ -897,8 +904,9 @@
 		 * means we are already losing data; need to let the decoder
 		 * know.
 		 */
-		if (!intel_pt_validate_hw_cap(PT_CAP_topa_multiple_entries) ||
-		    buf->output_off == pt_buffer_region_size(buf)) {
+		if (!buf->single &&
+		    (!intel_pt_validate_hw_cap(PT_CAP_topa_multiple_entries) ||
+		     buf->output_off == pt_buffer_region_size(buf))) {
 			perf_aux_output_flag(&pt->handle,
 			                     PERF_AUX_FLAG_TRUNCATED);
 			advance++;
@@ -970,7 +978,7 @@
 	 * order allocations, there shouldn't be many of these.
 	 */
 	list_for_each_entry(topa, &buf->tables, list) {
-		if (topa->offset + topa->size > pg << PAGE_SHIFT)
+		if (topa->offset + topa->size > (unsigned long)pg << PAGE_SHIFT)
 			goto found;
 	}
 
@@ -1244,6 +1252,15 @@
 	if (1 << order != nr_pages)
 		goto out;
 
+	/*
+	 * Some processors cannot always support single range for more than
+	 * 4KB - refer errata TGL052, ADL037 and RPL017. Future processors might
+	 * also be affected, so for now rather than trying to keep track of
+	 * which ones, just disable it for all.
+	 */
+	if (nr_pages > 1)
+		goto out;
+
 	buf->single = true;
 	buf->nr_pages = nr_pages;
 	ret = 0;
@@ -1347,10 +1364,26 @@
 	event->hw.addr_filters = NULL;
 }
 
-static inline bool valid_kernel_ip(unsigned long ip)
-{
-	return virt_addr_valid(ip) && kernel_ip(ip);
-}
+#ifdef CONFIG_X86_64
+/* Clamp to a canonical address greater-than-or-equal-to the address given */
+static u64 clamp_to_ge_canonical_addr(u64 vaddr, u8 vaddr_bits)
+{
+	return __is_canonical_address(vaddr, vaddr_bits) ?
+	       vaddr :
+	       -BIT_ULL(vaddr_bits - 1);
+}
+
+/* Clamp to a canonical address less-than-or-equal-to the address given */
+static u64 clamp_to_le_canonical_addr(u64 vaddr, u8 vaddr_bits)
+{
+	return __is_canonical_address(vaddr, vaddr_bits) ?
+	       vaddr :
+	       BIT_ULL(vaddr_bits - 1) - 1;
+}
+#else
+#define clamp_to_ge_canonical_addr(x, y) (x)
+#define clamp_to_le_canonical_addr(x, y) (x)
+#endif
 
 static int pt_event_addr_filters_validate(struct list_head *filters)
 {
@@ -1366,14 +1399,6 @@
 		    filter->action == PERF_ADDR_FILTER_ACTION_START)
 			return -EOPNOTSUPP;
 
-		if (!filter->path.dentry) {
-			if (!valid_kernel_ip(filter->offset))
-				return -EINVAL;
-
-			if (!valid_kernel_ip(filter->offset + filter->size))
-				return -EINVAL;
-		}
-
 		if (++range > intel_pt_validate_hw_cap(PT_CAP_num_address_ranges))
 			return -EOPNOTSUPP;
 	}
@@ -1397,9 +1422,26 @@
 		if (filter->path.dentry && !fr[range].start) {
 			msr_a = msr_b = 0;
 		} else {
-			/* apply the offset */
-			msr_a = fr[range].start;
-			msr_b = msr_a + fr[range].size - 1;
+			unsigned long n = fr[range].size - 1;
+			unsigned long a = fr[range].start;
+			unsigned long b;
+
+			if (a > ULONG_MAX - n)
+				b = ULONG_MAX;
+			else
+				b = a + n;
+			/*
+			 * Apply the offset. 64-bit addresses written to the
+			 * MSRs must be canonical, but the range can encompass
+			 * non-canonical addresses. Since software cannot
+			 * execute at non-canonical addresses, adjusting to
+			 * canonical addresses does not affect the result of the
+			 * address filter.
+			 */
+			msr_a = clamp_to_ge_canonical_addr(a, boot_cpu_data.x86_virt_bits);
+			msr_b = clamp_to_le_canonical_addr(b, boot_cpu_data.x86_virt_bits);
+			if (msr_b < msr_a)
+				msr_a = msr_b = 0;
 		}
 
 		filters->filter[range].msr_a  = msr_a;
@@ -1549,6 +1591,7 @@
 	 * see comment in intel_pt_interrupt().
 	 */
 	WRITE_ONCE(pt->handle_nmi, 0);
+	barrier();
 
 	pt_config_stop(event);
 
@@ -1600,11 +1643,10 @@
 		return 0;
 
 	/*
-	 * Here, handle_nmi tells us if the tracing is on
+	 * There is no PT interrupt in this mode, so stop the trace and it will
+	 * remain stopped while the buffer is copied.
 	 */
-	if (READ_ONCE(pt->handle_nmi))
-		pt_config_stop(event);
-
+	pt_config_stop(event);
 	pt_read_offset(buf);
 	pt_update_head(pt);
 
@@ -1616,11 +1658,10 @@
 	ret = perf_output_copy_aux(&pt->handle, handle, from, to);
 
 	/*
-	 * If the tracing was on when we turned up, restart it.
-	 * Compiler barrier not needed as we couldn't have been
-	 * preempted by anything that touches pt->handle_nmi.
+	 * Here, handle_nmi tells us if the tracing was on.
+	 * If the tracing was on, restart it.
 	 */
-	if (pt->handle_nmi)
+	if (READ_ONCE(pt->handle_nmi))
 		pt_config_start(event);
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/pt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/pt.h
@@ -33,8 +33,8 @@
 	u64	rsvd2	: 1;
 	u64	size	: 4;
 	u64	rsvd3	: 2;
-	u64	base	: 36;
-	u64	rsvd4	: 16;
+	u64	base	: 40;
+	u64	rsvd4	: 12;
 };
 
 /* TSC to Core Crystal Clock Ratio */
@@ -65,6 +65,7 @@
  * @head:	logical write offset inside the buffer
  * @snapshot:	if this is for a snapshot/overwrite counter
  * @single:	use Single Range Output instead of ToPA
+ * @wrapped:	buffer advance wrapped back to the first topa table
  * @stop_pos:	STOP topa entry index
  * @intr_pos:	INT topa entry index
  * @stop_te:	STOP topa entry pointer
@@ -82,6 +83,7 @@
 	local64_t		head;
 	bool			snapshot;
 	bool			single;
+	bool			wrapped;
 	long			stop_pos, intr_pos;
 	struct topa_entry	*stop_te, *intr_te;
 	void			**data_pages;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/uncore.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/uncore.c
@@ -1829,6 +1829,7 @@
 	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE,		&adl_uncore_init),
 	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L,		&adl_uncore_init),
 	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X,	&spr_uncore_init),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X,	&spr_uncore_init),
 	X86_MATCH_INTEL_FAM6_MODEL(ATOM_TREMONT_D,	&snr_uncore_init),
 	{},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/uncore.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/uncore.h
@@ -2,6 +2,7 @@
 #include <linux/slab.h>
 #include <linux/pci.h>
 #include <asm/apicdef.h>
+#include <asm/intel-family.h>
 #include <linux/io-64-nonatomic-lo-hi.h>
 
 #include <linux/perf_event.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/uncore_discovery.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/uncore_discovery.c
@@ -140,13 +140,21 @@
 	unsigned int *box_offset, *ids;
 	int i;
 
-	if (WARN_ON_ONCE(!unit->ctl || !unit->ctl_offset || !unit->ctr_offset))
+	if (!unit->ctl || !unit->ctl_offset || !unit->ctr_offset) {
+		pr_info("Invalid address is detected for uncore type %d box %d, "
+			"Disable the uncore unit.\n",
+			unit->box_type, unit->box_id);
 		return;
+	}
 
 	if (parsed) {
 		type = search_uncore_discovery_type(unit->box_type);
-		if (WARN_ON_ONCE(!type))
+		if (!type) {
+			pr_info("A spurious uncore type %d is detected, "
+				"Disable the uncore type.\n",
+				unit->box_type);
 			return;
+		}
 		/* Store the first box of each die */
 		if (!type->box_ctrl_die[die])
 			type->box_ctrl_die[die] = unit->ctl;
@@ -181,8 +189,12 @@
 		ids[i] = type->ids[i];
 		box_offset[i] = type->box_offset[i];
 
-		if (WARN_ON_ONCE(unit->box_id == ids[i]))
+		if (unit->box_id == ids[i]) {
+			pr_info("Duplicate uncore type %d box ID %d is detected, "
+				"Drop the duplicate uncore unit.\n",
+				unit->box_type, unit->box_id);
 			goto free_ids;
+		}
 	}
 	ids[i] = unit->box_id;
 	box_offset[i] = unit->ctl - type->box_ctrl;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/uncore_discovery.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/uncore_discovery.h
@@ -30,7 +30,7 @@
 
 
 #define uncore_discovery_invalid_unit(unit)			\
-	(!unit.table1 || !unit.ctl || !unit.table3 ||	\
+	(!unit.table1 || !unit.ctl || \
 	 unit.table1 == -1ULL || unit.ctl == -1ULL ||	\
 	 unit.table3 == -1ULL)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/uncore_snb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/uncore_snb.c
@@ -788,6 +788,22 @@
 	return 0;
 }
 
+static u64 snb_uncore_imc_read_counter(struct intel_uncore_box *box, struct perf_event *event)
+{
+	struct hw_perf_event *hwc = &event->hw;
+
+	/*
+	 * SNB IMC counters are 32-bit and are laid out back to back
+	 * in MMIO space. Therefore we must use a 32-bit accessor function
+	 * using readq() from uncore_mmio_read_counter() causes problems
+	 * because it is reading 64-bit at a time. This is okay for the
+	 * uncore_perf_event_update() function because it drops the upper
+	 * 32-bits but not okay for plain uncore_read_counter() as invoked
+	 * in uncore_pmu_event_start().
+	 */
+	return (u64)readl(box->io_addr + hwc->event_base);
+}
+
 static struct pmu snb_uncore_imc_pmu = {
 	.task_ctx_nr	= perf_invalid_context,
 	.event_init	= snb_uncore_imc_event_init,
@@ -807,7 +823,7 @@
 	.disable_event	= snb_uncore_imc_disable_event,
 	.enable_event	= snb_uncore_imc_enable_event,
 	.hw_config	= snb_uncore_imc_hw_config,
-	.read_counter	= uncore_mmio_read_counter,
+	.read_counter	= snb_uncore_imc_read_counter,
 };
 
 static struct intel_uncore_type snb_uncore_imc = {
@@ -1407,6 +1423,7 @@
 	/* MCHBAR is disabled */
 	if (!(mch_bar & BIT(0))) {
 		pr_warn("perf uncore: MCHBAR is disabled. Failed to map IMC free-running counters.\n");
+		pci_dev_put(pdev);
 		return;
 	}
 	mch_bar &= ~BIT(0);
@@ -1420,6 +1437,8 @@
 	box->io_addr = ioremap(addr, type->mmio_map_size);
 	if (!box->io_addr)
 		pr_warn("perf uncore: Failed to ioremap for %s.\n", type->name);
+
+	pci_dev_put(pdev);
 }
 
 static struct intel_uncore_ops tgl_uncore_imc_freerunning_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/intel/uncore_snbep.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/intel/uncore_snbep.c
@@ -452,13 +452,14 @@
 #define ICX_M3UPI_PCI_PMON_BOX_CTL		0xa0
 
 /* ICX IMC */
-#define ICX_NUMBER_IMC_CHN			2
+#define ICX_NUMBER_IMC_CHN			3
 #define ICX_IMC_MEM_STRIDE			0x4
 
 /* SPR */
 #define SPR_RAW_EVENT_MASK_EXT			0xffffff
 
 /* SPR CHA */
+#define SPR_CHA_EVENT_MASK_EXT			0xffffffff
 #define SPR_CHA_PMON_CTL_TID_EN			(1 << 16)
 #define SPR_CHA_PMON_EVENT_MASK			(SNBEP_PMON_RAW_EVENT_MASK | \
 						 SPR_CHA_PMON_CTL_TID_EN)
@@ -475,6 +476,7 @@
 DEFINE_UNCORE_FORMAT_ATTR(umask_ext2, umask, "config:8-15,32-57");
 DEFINE_UNCORE_FORMAT_ATTR(umask_ext3, umask, "config:8-15,32-39");
 DEFINE_UNCORE_FORMAT_ATTR(umask_ext4, umask, "config:8-15,32-55");
+DEFINE_UNCORE_FORMAT_ATTR(umask_ext5, umask, "config:8-15,32-63");
 DEFINE_UNCORE_FORMAT_ATTR(qor, qor, "config:16");
 DEFINE_UNCORE_FORMAT_ATTR(edge, edge, "config:18");
 DEFINE_UNCORE_FORMAT_ATTR(tid_en, tid_en, "config:19");
@@ -2891,6 +2893,7 @@
 		return false;
 
 	pci_read_config_dword(dev, HSWEP_PCU_CAPID4_OFFET, &capid4);
+	pci_dev_put(dev);
 	if (!hswep_get_chop(capid4))
 		return true;
 
@@ -3608,6 +3611,9 @@
 	struct hw_perf_event_extra *reg1 = &event->hw.extra_reg;
 	struct extra_reg *er;
 	int idx = 0;
+	/* Any of the CHA events may be filtered by Thread/Core-ID.*/
+	if (event->hw.config & SNBEP_CBO_PMON_CTL_TID_EN)
+		idx = SKX_CHA_MSR_PMON_BOX_FILTER_TID;
 
 	for (er = skx_uncore_cha_extra_regs; er->msr; er++) {
 		if (er->event != (event->hw.config & er->config_mask))
@@ -3675,6 +3681,7 @@
 	UNCORE_EVENT_CONSTRAINT(0xc0, 0xc),
 	UNCORE_EVENT_CONSTRAINT(0xc5, 0xc),
 	UNCORE_EVENT_CONSTRAINT(0xd4, 0xc),
+	UNCORE_EVENT_CONSTRAINT(0xd5, 0xc),
 	EVENT_CONSTRAINT_END
 };
 
@@ -3799,6 +3806,21 @@
 	NULL,
 };
 
+static void pmu_clear_mapping_attr(const struct attribute_group **groups,
+				   struct attribute_group *ag)
+{
+	int i;
+
+	for (i = 0; groups[i]; i++) {
+		if (groups[i] == ag) {
+			for (i++; groups[i]; i++)
+				groups[i - 1] = groups[i];
+			groups[i - 1] = NULL;
+			break;
+		}
+	}
+}
+
 static int
 pmu_iio_set_mapping(struct intel_uncore_type *type, struct attribute_group *ag)
 {
@@ -3847,7 +3869,7 @@
 clear_topology:
 	kfree(type->topology);
 clear_attr_update:
-	type->attr_update = NULL;
+	pmu_clear_mapping_attr(type->attr_update, ag);
 	return ret;
 }
 
@@ -4488,6 +4510,8 @@
 		type->topology = NULL;
 	}
 
+	pci_dev_put(dev);
+
 	return ret;
 }
 
@@ -4525,6 +4549,13 @@
 	pmu_iio_cleanup_mapping(type, &snr_iio_mapping_group);
 }
 
+static struct event_constraint snr_uncore_iio_constraints[] = {
+	UNCORE_EVENT_CONSTRAINT(0x83, 0x3),
+	UNCORE_EVENT_CONSTRAINT(0xc0, 0xc),
+	UNCORE_EVENT_CONSTRAINT(0xd5, 0xc),
+	EVENT_CONSTRAINT_END
+};
+
 static struct intel_uncore_type snr_uncore_iio = {
 	.name			= "iio",
 	.num_counters		= 4,
@@ -4536,6 +4567,7 @@
 	.event_mask_ext		= SNR_IIO_PMON_RAW_EVENT_MASK_EXT,
 	.box_ctl		= SNR_IIO_MSR_PMON_BOX_CTL,
 	.msr_offset		= SNR_IIO_MSR_OFFSET,
+	.constraints		= snr_uncore_iio_constraints,
 	.ops			= &ivbep_uncore_msr_ops,
 	.format_group		= &snr_uncore_iio_format_group,
 	.attr_update		= snr_iio_attr_update,
@@ -4845,6 +4877,8 @@
 
 	addr += box_ctl;
 
+	pci_dev_put(pdev);
+
 	box->io_addr = ioremap(addr, type->mmio_map_size);
 	if (!box->io_addr) {
 		pr_warn("perf uncore: Failed to ioremap for %s.\n", type->name);
@@ -5076,8 +5110,10 @@
 	UNCORE_EVENT_CONSTRAINT(0x02, 0x3),
 	UNCORE_EVENT_CONSTRAINT(0x03, 0x3),
 	UNCORE_EVENT_CONSTRAINT(0x83, 0x3),
+	UNCORE_EVENT_CONSTRAINT(0x88, 0xc),
 	UNCORE_EVENT_CONSTRAINT(0xc0, 0xc),
 	UNCORE_EVENT_CONSTRAINT(0xc5, 0xc),
+	UNCORE_EVENT_CONSTRAINT(0xd5, 0xc),
 	EVENT_CONSTRAINT_END
 };
 
@@ -5125,6 +5161,11 @@
 
 static int icx_iio_set_mapping(struct intel_uncore_type *type)
 {
+	/* Detect ICX-D system. This case is not supported */
+	if (boot_cpu_data.x86_model == INTEL_FAM6_ICELAKE_D) {
+		pmu_clear_mapping_attr(type->attr_update, &icx_iio_mapping_group);
+		return -EPERM;
+	}
 	return pmu_iio_set_mapping(type, &icx_iio_mapping_group);
 }
 
@@ -5463,12 +5504,12 @@
 static struct intel_uncore_type icx_uncore_imc = {
 	.name		= "imc",
 	.num_counters   = 4,
-	.num_boxes	= 8,
+	.num_boxes	= 12,
 	.perf_ctr_bits	= 48,
 	.fixed_ctr_bits	= 48,
 	.fixed_ctr	= SNR_IMC_MMIO_PMON_FIXED_CTR,
 	.fixed_ctl	= SNR_IMC_MMIO_PMON_FIXED_CTL,
-	.event_descs	= hswep_uncore_imc_events,
+	.event_descs	= snr_uncore_imc_events,
 	.perf_ctr	= SNR_IMC_MMIO_PMON_CTR0,
 	.event_ctl	= SNR_IMC_MMIO_PMON_CTL0,
 	.event_mask	= SNBEP_PMON_RAW_EVENT_MASK,
@@ -5609,7 +5650,7 @@
 
 static struct attribute *spr_uncore_cha_formats_attr[] = {
 	&format_attr_event.attr,
-	&format_attr_umask_ext4.attr,
+	&format_attr_umask_ext5.attr,
 	&format_attr_tid_en2.attr,
 	&format_attr_edge.attr,
 	&format_attr_inv.attr,
@@ -5645,8 +5686,9 @@
 static struct intel_uncore_type spr_uncore_chabox = {
 	.name			= "cha",
 	.event_mask		= SPR_CHA_PMON_EVENT_MASK,
-	.event_mask_ext		= SPR_RAW_EVENT_MASK_EXT,
+	.event_mask_ext		= SPR_CHA_EVENT_MASK_EXT,
 	.num_shared_regs	= 1,
+	.constraints		= skx_uncore_chabox_constraints,
 	.ops			= &spr_uncore_chabox_ops,
 	.format_group		= &spr_uncore_chabox_format_group,
 	.attr_update		= uncore_alias_groups,
@@ -5658,6 +5700,7 @@
 	.event_mask_ext		= SNR_IIO_PMON_RAW_EVENT_MASK_EXT,
 	.format_group		= &snr_uncore_iio_format_group,
 	.attr_update		= uncore_alias_groups,
+	.constraints		= icx_uncore_iio_constraints,
 };
 
 static struct attribute *spr_uncore_raw_formats_attr[] = {
@@ -5686,9 +5729,16 @@
 
 };
 
+static struct event_constraint spr_uncore_m2pcie_constraints[] = {
+	UNCORE_EVENT_CONSTRAINT(0x14, 0x3),
+	UNCORE_EVENT_CONSTRAINT(0x2d, 0x3),
+	EVENT_CONSTRAINT_END
+};
+
 static struct intel_uncore_type spr_uncore_m2pcie = {
 	SPR_UNCORE_COMMON_FORMAT(),
 	.name			= "m2pcie",
+	.constraints		= spr_uncore_m2pcie_constraints,
 };
 
 static struct intel_uncore_type spr_uncore_pcu = {
@@ -5765,6 +5815,7 @@
 static struct intel_uncore_type spr_uncore_m3upi = {
 	SPR_UNCORE_PCI_COMMON_FORMAT(),
 	.name			= "m3upi",
+	.constraints		= icx_uncore_m3upi_constraints,
 };
 
 static struct intel_uncore_type spr_uncore_mdf = {
@@ -5773,6 +5824,7 @@
 };
 
 #define UNCORE_SPR_NUM_UNCORE_TYPES		12
+#define UNCORE_SPR_CHA				0
 #define UNCORE_SPR_IIO				1
 #define UNCORE_SPR_IMC				6
 
@@ -6015,12 +6067,32 @@
 	return max + 1;
 }
 
+#define SPR_MSR_UNC_CBO_CONFIG		0x2FFE
+
 void spr_uncore_cpu_init(void)
 {
+	struct intel_uncore_type *type;
+	u64 num_cbo;
+
 	uncore_msr_uncores = uncore_get_uncores(UNCORE_ACCESS_MSR,
 						UNCORE_SPR_MSR_EXTRA_UNCORES,
 						spr_msr_uncores);
 
+	type = uncore_find_type_by_id(uncore_msr_uncores, UNCORE_SPR_CHA);
+	if (type) {
+		/*
+		 * The value from the discovery table (stored in the type->num_boxes
+		 * of UNCORE_SPR_CHA) is incorrect on some SPR variants because of a
+		 * firmware bug. Using the value from SPR_MSR_UNC_CBO_CONFIG to replace it.
+		 */
+		rdmsrl(SPR_MSR_UNC_CBO_CONFIG, num_cbo);
+		/*
+		 * The MSR doesn't work on the EMR XCC, but the firmware bug doesn't impact
+		 * the EMR XCC. Don't let the value from the MSR replace the existing value.
+		 */
+		if (num_cbo)
+			type->num_boxes = num_cbo;
+	}
 	spr_uncore_iio_free_running.num_boxes = uncore_type_max_boxes(uncore_msr_uncores, UNCORE_SPR_IIO);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/msr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/msr.c
@@ -69,6 +69,7 @@
 	case INTEL_FAM6_BROADWELL_G:
 	case INTEL_FAM6_BROADWELL_X:
 	case INTEL_FAM6_SAPPHIRERAPIDS_X:
+	case INTEL_FAM6_EMERALDRAPIDS_X:
 
 	case INTEL_FAM6_ATOM_SILVERMONT:
 	case INTEL_FAM6_ATOM_SILVERMONT_D:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/perf_event.h
@@ -14,6 +14,7 @@
 
 #include <linux/perf_event.h>
 
+#include <asm/fpu/xstate.h>
 #include <asm/intel_ds.h>
 #include <asm/cpu.h>
 
@@ -1181,6 +1182,68 @@
 	regs->ip = ip;
 }
 
+/*
+ * x86control flow change classification
+ * x86control flow changes include branches, interrupts, traps, faults
+ */
+enum {
+	X86_BR_NONE		= 0,      /* unknown */
+
+	X86_BR_USER		= 1 << 0, /* branch target is user */
+	X86_BR_KERNEL		= 1 << 1, /* branch target is kernel */
+
+	X86_BR_CALL		= 1 << 2, /* call */
+	X86_BR_RET		= 1 << 3, /* return */
+	X86_BR_SYSCALL		= 1 << 4, /* syscall */
+	X86_BR_SYSRET		= 1 << 5, /* syscall return */
+	X86_BR_INT		= 1 << 6, /* sw interrupt */
+	X86_BR_IRET		= 1 << 7, /* return from interrupt */
+	X86_BR_JCC		= 1 << 8, /* conditional */
+	X86_BR_JMP		= 1 << 9, /* jump */
+	X86_BR_IRQ		= 1 << 10,/* hw interrupt or trap or fault */
+	X86_BR_IND_CALL		= 1 << 11,/* indirect calls */
+	X86_BR_ABORT		= 1 << 12,/* transaction abort */
+	X86_BR_IN_TX		= 1 << 13,/* in transaction */
+	X86_BR_NO_TX		= 1 << 14,/* not in transaction */
+	X86_BR_ZERO_CALL	= 1 << 15,/* zero length call */
+	X86_BR_CALL_STACK	= 1 << 16,/* call stack */
+	X86_BR_IND_JMP		= 1 << 17,/* indirect jump */
+
+	X86_BR_TYPE_SAVE	= 1 << 18,/* indicate to save branch type */
+
+};
+
+#define X86_BR_PLM (X86_BR_USER | X86_BR_KERNEL)
+#define X86_BR_ANYTX (X86_BR_NO_TX | X86_BR_IN_TX)
+
+#define X86_BR_ANY       \
+	(X86_BR_CALL    |\
+	 X86_BR_RET     |\
+	 X86_BR_SYSCALL |\
+	 X86_BR_SYSRET  |\
+	 X86_BR_INT     |\
+	 X86_BR_IRET    |\
+	 X86_BR_JCC     |\
+	 X86_BR_JMP	 |\
+	 X86_BR_IRQ	 |\
+	 X86_BR_ABORT	 |\
+	 X86_BR_IND_CALL |\
+	 X86_BR_IND_JMP  |\
+	 X86_BR_ZERO_CALL)
+
+#define X86_BR_ALL (X86_BR_PLM | X86_BR_ANY)
+
+#define X86_BR_ANY_CALL		 \
+	(X86_BR_CALL		|\
+	 X86_BR_IND_CALL	|\
+	 X86_BR_ZERO_CALL	|\
+	 X86_BR_SYSCALL		|\
+	 X86_BR_IRQ		|\
+	 X86_BR_INT)
+
+int common_branch_type(int type);
+int branch_type(unsigned long from, unsigned long to, int abort);
+
 ssize_t x86_event_sysfs_show(char *page, u64 config, u64 event);
 ssize_t intel_event_sysfs_show(char *page, u64 config);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/rapl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/rapl.c
@@ -536,11 +536,14 @@
  * - perf_msr_probe(PERF_RAPL_MAX)
  * - want to use same event codes across both architectures
  */
-static struct perf_msr amd_rapl_msrs[PERF_RAPL_MAX] = {
-	[PERF_RAPL_PKG]  = { MSR_AMD_PKG_ENERGY_STATUS,  &rapl_events_pkg_group,   test_msr },
+static struct perf_msr amd_rapl_msrs[] = {
+	[PERF_RAPL_PP0]  = { 0, &rapl_events_cores_group, 0, false, 0 },
+	[PERF_RAPL_PKG]  = { MSR_AMD_PKG_ENERGY_STATUS,  &rapl_events_pkg_group,   test_msr, false, RAPL_MSR_MASK },
+	[PERF_RAPL_RAM]  = { 0, &rapl_events_ram_group,   0, false, 0 },
+	[PERF_RAPL_PP1]  = { 0, &rapl_events_gpu_group,   0, false, 0 },
+	[PERF_RAPL_PSYS] = { 0, &rapl_events_psys_group,  0, false, 0 },
 };
 
-
 static int rapl_cpu_offline(unsigned int cpu)
 {
 	struct rapl_pmu *pmu = cpu_to_rapl_pmu(cpu);
@@ -801,9 +804,12 @@
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X,		&model_hsx),
 	X86_MATCH_INTEL_FAM6_MODEL(COMETLAKE_L,		&model_skl),
 	X86_MATCH_INTEL_FAM6_MODEL(COMETLAKE,		&model_skl),
+	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE_L,		&model_skl),
+	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE,		&model_skl),
 	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE,		&model_skl),
 	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L,		&model_skl),
 	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X,	&model_spr),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X,	&model_spr),
 	{},
 };
 MODULE_DEVICE_TABLE(x86cpu, rapl_model_match);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/utils.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/utils.c
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <asm/insn.h>
+#include <linux/mm.h>
+
+#include "perf_event.h"
+
+/*
+ * return the type of control flow change at address "from"
+ * instruction is not necessarily a branch (in case of interrupt).
+ *
+ * The branch type returned also includes the priv level of the
+ * target of the control flow change (X86_BR_USER, X86_BR_KERNEL).
+ *
+ * If a branch type is unknown OR the instruction cannot be
+ * decoded (e.g., text page not present), then X86_BR_NONE is
+ * returned.
+ */
+int branch_type(unsigned long from, unsigned long to, int abort)
+{
+	struct insn insn;
+	void *addr;
+	int bytes_read, bytes_left;
+	int ret = X86_BR_NONE;
+	int ext, to_plm, from_plm;
+	u8 buf[MAX_INSN_SIZE];
+	int is64 = 0;
+
+	to_plm = kernel_ip(to) ? X86_BR_KERNEL : X86_BR_USER;
+	from_plm = kernel_ip(from) ? X86_BR_KERNEL : X86_BR_USER;
+
+	/*
+	 * maybe zero if lbr did not fill up after a reset by the time
+	 * we get a PMU interrupt
+	 */
+	if (from == 0 || to == 0)
+		return X86_BR_NONE;
+
+	if (abort)
+		return X86_BR_ABORT | to_plm;
+
+	if (from_plm == X86_BR_USER) {
+		/*
+		 * can happen if measuring at the user level only
+		 * and we interrupt in a kernel thread, e.g., idle.
+		 */
+		if (!current->mm)
+			return X86_BR_NONE;
+
+		/* may fail if text not present */
+		bytes_left = copy_from_user_nmi(buf, (void __user *)from,
+						MAX_INSN_SIZE);
+		bytes_read = MAX_INSN_SIZE - bytes_left;
+		if (!bytes_read)
+			return X86_BR_NONE;
+
+		addr = buf;
+	} else {
+		/*
+		 * The LBR logs any address in the IP, even if the IP just
+		 * faulted. This means userspace can control the from address.
+		 * Ensure we don't blindly read any address by validating it is
+		 * a known text address and not a vsyscall address.
+		 */
+		if (kernel_text_address(from) && !in_gate_area_no_mm(from)) {
+			addr = (void *)from;
+			/*
+			 * Assume we can get the maximum possible size
+			 * when grabbing kernel data.  This is not
+			 * _strictly_ true since we could possibly be
+			 * executing up next to a memory hole, but
+			 * it is very unlikely to be a problem.
+			 */
+			bytes_read = MAX_INSN_SIZE;
+		} else {
+			return X86_BR_NONE;
+		}
+	}
+
+	/*
+	 * decoder needs to know the ABI especially
+	 * on 64-bit systems running 32-bit apps
+	 */
+#ifdef CONFIG_X86_64
+	is64 = kernel_ip((unsigned long)addr) || any_64bit_mode(current_pt_regs());
+#endif
+	insn_init(&insn, addr, bytes_read, is64);
+	if (insn_get_opcode(&insn))
+		return X86_BR_ABORT;
+
+	switch (insn.opcode.bytes[0]) {
+	case 0xf:
+		switch (insn.opcode.bytes[1]) {
+		case 0x05: /* syscall */
+		case 0x34: /* sysenter */
+			ret = X86_BR_SYSCALL;
+			break;
+		case 0x07: /* sysret */
+		case 0x35: /* sysexit */
+			ret = X86_BR_SYSRET;
+			break;
+		case 0x80 ... 0x8f: /* conditional */
+			ret = X86_BR_JCC;
+			break;
+		default:
+			ret = X86_BR_NONE;
+		}
+		break;
+	case 0x70 ... 0x7f: /* conditional */
+		ret = X86_BR_JCC;
+		break;
+	case 0xc2: /* near ret */
+	case 0xc3: /* near ret */
+	case 0xca: /* far ret */
+	case 0xcb: /* far ret */
+		ret = X86_BR_RET;
+		break;
+	case 0xcf: /* iret */
+		ret = X86_BR_IRET;
+		break;
+	case 0xcc ... 0xce: /* int */
+		ret = X86_BR_INT;
+		break;
+	case 0xe8: /* call near rel */
+		if (insn_get_immediate(&insn) || insn.immediate1.value == 0) {
+			/* zero length call */
+			ret = X86_BR_ZERO_CALL;
+			break;
+		}
+		fallthrough;
+	case 0x9a: /* call far absolute */
+		ret = X86_BR_CALL;
+		break;
+	case 0xe0 ... 0xe3: /* loop jmp */
+		ret = X86_BR_JCC;
+		break;
+	case 0xe9 ... 0xeb: /* jmp */
+		ret = X86_BR_JMP;
+		break;
+	case 0xff: /* call near absolute, call far absolute ind */
+		if (insn_get_modrm(&insn))
+			return X86_BR_ABORT;
+
+		ext = (insn.modrm.bytes[0] >> 3) & 0x7;
+		switch (ext) {
+		case 2: /* near ind call */
+		case 3: /* far ind call */
+			ret = X86_BR_IND_CALL;
+			break;
+		case 4:
+		case 5:
+			ret = X86_BR_IND_JMP;
+			break;
+		}
+		break;
+	default:
+		ret = X86_BR_NONE;
+	}
+	/*
+	 * interrupts, traps, faults (and thus ring transition) may
+	 * occur on any instructions. Thus, to classify them correctly,
+	 * we need to first look at the from and to priv levels. If they
+	 * are different and to is in the kernel, then it indicates
+	 * a ring transition. If the from instruction is not a ring
+	 * transition instr (syscall, systenter, int), then it means
+	 * it was a irq, trap or fault.
+	 *
+	 * we have no way of detecting kernel to kernel faults.
+	 */
+	if (from_plm == X86_BR_USER && to_plm == X86_BR_KERNEL
+	    && ret != X86_BR_SYSCALL && ret != X86_BR_INT)
+		ret = X86_BR_IRQ;
+
+	/*
+	 * branch priv level determined by target as
+	 * is done by HW when LBR_SELECT is implemented
+	 */
+	if (ret != X86_BR_NONE)
+		ret |= to_plm;
+
+	return ret;
+}
+
+#define X86_BR_TYPE_MAP_MAX	16
+
+static int branch_map[X86_BR_TYPE_MAP_MAX] = {
+	PERF_BR_CALL,		/* X86_BR_CALL */
+	PERF_BR_RET,		/* X86_BR_RET */
+	PERF_BR_SYSCALL,	/* X86_BR_SYSCALL */
+	PERF_BR_SYSRET,		/* X86_BR_SYSRET */
+	PERF_BR_UNKNOWN,	/* X86_BR_INT */
+	PERF_BR_ERET,		/* X86_BR_IRET */
+	PERF_BR_COND,		/* X86_BR_JCC */
+	PERF_BR_UNCOND,		/* X86_BR_JMP */
+	PERF_BR_IRQ,		/* X86_BR_IRQ */
+	PERF_BR_IND_CALL,	/* X86_BR_IND_CALL */
+	PERF_BR_UNKNOWN,	/* X86_BR_ABORT */
+	PERF_BR_UNKNOWN,	/* X86_BR_IN_TX */
+	PERF_BR_UNKNOWN,	/* X86_BR_NO_TX */
+	PERF_BR_CALL,		/* X86_BR_ZERO_CALL */
+	PERF_BR_UNKNOWN,	/* X86_BR_CALL_STACK */
+	PERF_BR_IND,		/* X86_BR_IND_JMP */
+};
+
+int common_branch_type(int type)
+{
+	int i;
+
+	type >>= 2; /* skip X86_BR_USER and X86_BR_KERNEL */
+
+	if (type) {
+		i = __ffs(type);
+		if (i < X86_BR_TYPE_MAP_MAX)
+			return branch_map[i];
+	}
+
+	return PERF_BR_UNKNOWN;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/events/zhaoxin/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/events/zhaoxin/core.c
@@ -541,7 +541,13 @@
 
 	switch (boot_cpu_data.x86) {
 	case 0x06:
-		if (boot_cpu_data.x86_model == 0x0f || boot_cpu_data.x86_model == 0x19) {
+		/*
+		 * Support Zhaoxin CPU from ZXC series, exclude Nano series through FMS.
+		 * Nano FMS: Family=6, Model=F, Stepping=[0-A][C-D]
+		 * ZXC FMS: Family=6, Model=F, Stepping=E-F OR Family=6, Model=0x19, Stepping=0-3
+		 */
+		if ((boot_cpu_data.x86_model == 0x0f && boot_cpu_data.x86_stepping >= 0x0e) ||
+			boot_cpu_data.x86_model == 0x19) {
 
 			x86_pmu.max_period = x86_pmu.cntval_mask >> 1;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/hyperv/hv_init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/hyperv/hv_init.c
@@ -29,6 +29,14 @@
 #include <clocksource/hyperv_timer.h>
 #include <linux/highmem.h>
 
+#ifndef PKG_ABI
+/*
+ * Preserve the ability to 'make deb-pkg' since PKG_ABI is provided
+ * by the Ubuntu build rules.
+ */
+#define PKG_ABI 0
+#endif
+
 int hyperv_init_cpuhp;
 u64 hv_current_partition_id = ~0ull;
 EXPORT_SYMBOL_GPL(hv_current_partition_id);
@@ -45,7 +53,7 @@
 static int hv_cpu_init(unsigned int cpu)
 {
 	union hv_vp_assist_msr_contents msr = { 0 };
-	struct hv_vp_assist_page **hvp = &hv_vp_assist_page[smp_processor_id()];
+	struct hv_vp_assist_page **hvp = &hv_vp_assist_page[cpu];
 	int ret;
 
 	ret = hv_common_cpu_init(cpu);
@@ -55,34 +63,32 @@
 	if (!hv_vp_assist_page)
 		return 0;
 
-	if (!*hvp) {
-		if (hv_root_partition) {
-			/*
-			 * For root partition we get the hypervisor provided VP assist
-			 * page, instead of allocating a new page.
-			 */
-			rdmsrl(HV_X64_MSR_VP_ASSIST_PAGE, msr.as_uint64);
-			*hvp = memremap(msr.pfn <<
-					HV_X64_MSR_VP_ASSIST_PAGE_ADDRESS_SHIFT,
-					PAGE_SIZE, MEMREMAP_WB);
-		} else {
-			/*
-			 * The VP assist page is an "overlay" page (see Hyper-V TLFS's
-			 * Section 5.2.1 "GPA Overlay Pages"). Here it must be zeroed
-			 * out to make sure we always write the EOI MSR in
-			 * hv_apic_eoi_write() *after* the EOI optimization is disabled
-			 * in hv_cpu_die(), otherwise a CPU may not be stopped in the
-			 * case of CPU offlining and the VM will hang.
-			 */
+	if (hv_root_partition) {
+		/*
+		 * For root partition we get the hypervisor provided VP assist
+		 * page, instead of allocating a new page.
+		 */
+		rdmsrl(HV_X64_MSR_VP_ASSIST_PAGE, msr.as_uint64);
+		*hvp = memremap(msr.pfn << HV_X64_MSR_VP_ASSIST_PAGE_ADDRESS_SHIFT,
+				PAGE_SIZE, MEMREMAP_WB);
+	} else {
+		/*
+		 * The VP assist page is an "overlay" page (see Hyper-V TLFS's
+		 * Section 5.2.1 "GPA Overlay Pages"). Here it must be zeroed
+		 * out to make sure we always write the EOI MSR in
+		 * hv_apic_eoi_write() *after* the EOI optimization is disabled
+		 * in hv_cpu_die(), otherwise a CPU may not be stopped in the
+		 * case of CPU offlining and the VM will hang.
+		 */
+		if (!*hvp)
 			*hvp = __vmalloc(PAGE_SIZE, GFP_KERNEL | __GFP_ZERO);
-			if (*hvp)
-				msr.pfn = vmalloc_to_pfn(*hvp);
-		}
-		WARN_ON(!(*hvp));
-		if (*hvp) {
-			msr.enable = 1;
-			wrmsrl(HV_X64_MSR_VP_ASSIST_PAGE, msr.as_uint64);
-		}
+		if (*hvp)
+			msr.pfn = vmalloc_to_pfn(*hvp);
+
+	}
+	if (!WARN_ON(!(*hvp))) {
+		msr.enable = 1;
+		wrmsrl(HV_X64_MSR_VP_ASSIST_PAGE, msr.as_uint64);
 	}
 
 	return 0;
@@ -139,7 +145,6 @@
 	struct hv_reenlightenment_control re_ctrl = {
 		.vector = HYPERV_REENLIGHTENMENT_VECTOR,
 		.enabled = 1,
-		.target_vp = hv_vp_index[smp_processor_id()]
 	};
 	struct hv_tsc_emulation_control emu_ctrl = {.enabled = 1};
 
@@ -148,13 +153,20 @@
 		return;
 	}
 
+	if (!hv_vp_index)
+		return;
+
 	hv_reenlightenment_cb = cb;
 
 	/* Make sure callback is registered before we write to MSRs */
 	wmb();
 
+	re_ctrl.target_vp = hv_vp_index[get_cpu()];
+
 	wrmsrl(HV_X64_MSR_REENLIGHTENMENT_CONTROL, *((u64 *)&re_ctrl));
 	wrmsrl(HV_X64_MSR_TSC_EMULATION_CONTROL, *((u64 *)&emu_ctrl));
+
+	put_cpu();
 }
 EXPORT_SYMBOL_GPL(set_hv_tscchange_cb);
 
@@ -342,20 +354,13 @@
  */
 void __init hyperv_init(void)
 {
-	u64 guest_id, required_msrs;
+	u64 guest_id;
 	union hv_x64_msr_hypercall_contents hypercall_msr;
 	int cpuhp;
 
 	if (x86_hyper_type != X86_HYPER_MS_HYPERV)
 		return;
 
-	/* Absolutely required MSRs */
-	required_msrs = HV_MSR_HYPERCALL_AVAILABLE |
-		HV_MSR_VP_INDEX_AVAILABLE;
-
-	if ((ms_hyperv.features & required_msrs) != required_msrs)
-		return;
-
 	if (hv_common_init())
 		return;
 
@@ -376,7 +381,7 @@
 	 * 1. Register the guest ID
 	 * 2. Enable the hypercall and register the hypercall page
 	 */
-	guest_id = generate_guest_id(0, LINUX_VERSION_CODE, 0);
+	guest_id = generate_guest_id(0x80 /*Canonical*/, LINUX_VERSION_CODE, PKG_ABI);
 	wrmsrl(HV_X64_MSR_GUEST_OS_ID, guest_id);
 
 	hv_hypercall_pg = __vmalloc_node_range(PAGE_SIZE, 1, VMALLOC_START,
@@ -472,8 +477,6 @@
 {
 	union hv_x64_msr_hypercall_contents hypercall_msr;
 
-	unregister_syscore_ops(&hv_syscore_ops);
-
 	/* Reset our OS id */
 	wrmsrl(HV_X64_MSR_GUEST_OS_ID, 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/hyperv/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/hyperv/mmu.c
@@ -68,15 +68,6 @@
 
 	local_irq_save(flags);
 
-	/*
-	 * Only check the mask _after_ interrupt has been disabled to avoid the
-	 * mask changing under our feet.
-	 */
-	if (cpumask_empty(cpus)) {
-		local_irq_restore(flags);
-		return;
-	}
-
 	flush_pcpu = (struct hv_tlb_flush **)
 		     this_cpu_ptr(hyperv_pcpu_input_arg);
 
@@ -115,7 +106,9 @@
 		 * must. We will also check all VP numbers when walking the
 		 * supplied CPU set to remain correct in all cases.
 		 */
-		if (hv_cpu_number_to_vp_number(cpumask_last(cpus)) >= 64)
+		cpu = cpumask_last(cpus);
+
+		if (cpu < nr_cpumask_bits && hv_cpu_number_to_vp_number(cpu) >= 64)
 			goto do_ex_hypercall;
 
 		for_each_cpu(cpu, cpus) {
@@ -131,6 +124,12 @@
 			__set_bit(vcpu, (unsigned long *)
 				  &flush->processor_mask);
 		}
+
+		/* nothing to flush if 'processor_mask' ends up being empty */
+		if (!flush->processor_mask) {
+			local_irq_restore(flags);
+			return;
+		}
 	}
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/ia32/ia32_signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/ia32/ia32_signal.c
@@ -24,7 +24,6 @@
 #include <linux/syscalls.h>
 #include <asm/ucontext.h>
 #include <linux/uaccess.h>
-#include <asm/fpu/internal.h>
 #include <asm/fpu/signal.h>
 #include <asm/ptrace.h>
 #include <asm/ia32_unistd.h>
@@ -57,8 +56,8 @@
 /*
  * Do a signal return; undo the signal stack.
  */
-static int ia32_restore_sigcontext(struct pt_regs *regs,
-				   struct sigcontext_32 __user *usc)
+static bool ia32_restore_sigcontext(struct pt_regs *regs,
+				    struct sigcontext_32 __user *usc)
 {
 	struct sigcontext_32 sc;
 
@@ -66,7 +65,7 @@
 	current->restart_block.fn = do_no_restart_syscall;
 
 	if (unlikely(copy_from_user(&sc, usc, sizeof(sc))))
-		return -EFAULT;
+		return false;
 
 	/* Get only the ia32 registers. */
 	regs->bx = sc.bx;
@@ -111,7 +110,7 @@
 
 	set_current_blocked(&set);
 
-	if (ia32_restore_sigcontext(regs, &frame->sc))
+	if (!ia32_restore_sigcontext(regs, &frame->sc))
 		goto badframe;
 	return regs->ax;
 
@@ -135,7 +134,7 @@
 
 	set_current_blocked(&set);
 
-	if (ia32_restore_sigcontext(regs, &frame->uc.uc_mcontext))
+	if (!ia32_restore_sigcontext(regs, &frame->uc.uc_mcontext))
 		goto badframe;
 
 	if (compat_restore_altstack(&frame->uc.uc_stack))
@@ -220,8 +219,8 @@
 
 	sp = fpu__alloc_mathframe(sp, 1, &fx_aligned, &math_size);
 	*fpstate = (struct _fpstate_32 __user *) sp;
-	if (copy_fpstate_to_sigframe(*fpstate, (void __user *)fx_aligned,
-				     math_size) < 0)
+	if (!copy_fpstate_to_sigframe(*fpstate, (void __user *)fx_aligned,
+				      math_size))
 		return (void __user *) -1L;
 
 	sp -= frame_size;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/GEN-for-each-reg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/GEN-for-each-reg.h
@@ -1,11 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * These are in machine order; things rely on that.
+ */
 #ifdef CONFIG_64BIT
 GEN(rax)
-GEN(rbx)
 GEN(rcx)
 GEN(rdx)
+GEN(rbx)
+GEN(rsp)
+GEN(rbp)
 GEN(rsi)
 GEN(rdi)
-GEN(rbp)
 GEN(r8)
 GEN(r9)
 GEN(r10)
@@ -16,10 +21,11 @@
 GEN(r15)
 #else
 GEN(eax)
-GEN(ebx)
 GEN(ecx)
 GEN(edx)
+GEN(ebx)
+GEN(esp)
+GEN(ebp)
 GEN(esi)
 GEN(edi)
-GEN(ebp)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/acenv.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/acenv.h
@@ -13,7 +13,19 @@
 
 /* Asm macros */
 
-#define ACPI_FLUSH_CPU_CACHE()	wbinvd()
+/*
+ * ACPI_FLUSH_CPU_CACHE() flushes caches on entering sleep states.
+ * It is required to prevent data loss.
+ *
+ * While running inside virtual machine, the kernel can bypass cache flushing.
+ * Changing sleep state in a virtual machine doesn't affect the host system
+ * sleep state and cannot lead to data loss.
+ */
+#define ACPI_FLUSH_CPU_CACHE()					\
+do {								\
+	if (!cpu_feature_enabled(X86_FEATURE_HYPERVISOR))	\
+		wbinvd();					\
+} while (0)
 
 int __acpi_acquire_global_lock(unsigned int *lock);
 int __acpi_release_global_lock(unsigned int *lock);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/alternative.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/alternative.h
@@ -75,6 +75,8 @@
 
 extern void alternative_instructions(void);
 extern void apply_alternatives(struct alt_instr *start, struct alt_instr *end);
+extern void apply_retpolines(s32 *start, s32 *end);
+extern void apply_returns(s32 *start, s32 *end);
 
 struct module;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/amd_nb.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/amd_nb.h
@@ -118,7 +118,10 @@
 
 #define amd_nb_num(x)		0
 #define amd_nb_has_feature(x)	false
-#define node_to_amd_nb(x)	NULL
+static inline struct amd_northbridge *node_to_amd_nb(int node)
+{
+	return NULL;
+}
 #define amd_gart_present(x)	false
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/apic.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/apic.h
@@ -12,6 +12,7 @@
 #include <asm/mpspec.h>
 #include <asm/msr.h>
 #include <asm/hardirq.h>
+#include <asm/io.h>
 
 #define ARCH_APICTIMER_STOPS_ON_C3	1
 
@@ -111,7 +112,7 @@
 
 static inline u32 native_apic_mem_read(u32 reg)
 {
-	return *((volatile u32 *)(APIC_BASE + reg));
+	return readl((void __iomem *)(APIC_BASE + reg));
 }
 
 extern void native_apic_wait_icr_idle(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/apm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/apm.h
@@ -35,6 +35,7 @@
 	__asm__ __volatile__(APM_DO_ZERO_SEGS
 		"pushl %%edi\n\t"
 		"pushl %%ebp\n\t"
+		ANNOTATE_RETPOLINE_SAFE /* FRBS */
 		"lcall *%%cs:apm_bios_entry\n\t"
 		"setc %%al\n\t"
 		"popl %%ebp\n\t"
@@ -59,6 +60,7 @@
 	__asm__ __volatile__(APM_DO_ZERO_SEGS
 		"pushl %%edi\n\t"
 		"pushl %%ebp\n\t"
+		ANNOTATE_RETPOLINE_SAFE /* FRBS */
 		"lcall *%%cs:apm_bios_entry\n\t"
 		"setc %%bl\n\t"
 		"popl %%ebp\n\t"
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/asm-prototypes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/asm-prototypes.h
@@ -12,26 +12,9 @@
 #include <asm/special_insns.h>
 #include <asm/preempt.h>
 #include <asm/asm.h>
+#include <asm/nospec-branch.h>
 
 #ifndef CONFIG_X86_CMPXCHG64
 extern void cmpxchg8b_emu(void);
 #endif
 
-#ifdef CONFIG_RETPOLINE
-
-#undef GEN
-#define GEN(reg) \
-	extern asmlinkage void __x86_indirect_thunk_ ## reg (void);
-#include <asm/GEN-for-each-reg.h>
-
-#undef GEN
-#define GEN(reg) \
-	extern asmlinkage void __x86_indirect_alt_call_ ## reg (void);
-#include <asm/GEN-for-each-reg.h>
-
-#undef GEN
-#define GEN(reg) \
-	extern asmlinkage void __x86_indirect_alt_jmp_ ## reg (void);
-#include <asm/GEN-for-each-reg.h>
-
-#endif /* CONFIG_RETPOLINE */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/asm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/asm.h
@@ -6,11 +6,13 @@
 # define __ASM_FORM(x, ...)		x,## __VA_ARGS__
 # define __ASM_FORM_RAW(x, ...)		x,## __VA_ARGS__
 # define __ASM_FORM_COMMA(x, ...)	x,## __VA_ARGS__,
+# define __ASM_REGPFX			%
 #else
 #include <linux/stringify.h>
 # define __ASM_FORM(x, ...)		" " __stringify(x,##__VA_ARGS__) " "
 # define __ASM_FORM_RAW(x, ...)		    __stringify(x,##__VA_ARGS__)
 # define __ASM_FORM_COMMA(x, ...)	" " __stringify(x,##__VA_ARGS__) ","
+# define __ASM_REGPFX			%%
 #endif
 
 #define _ASM_BYTES(x, ...)	__ASM_FORM(.byte x,##__VA_ARGS__ ;)
@@ -49,6 +51,9 @@
 #define _ASM_SI		__ASM_REG(si)
 #define _ASM_DI		__ASM_REG(di)
 
+/* Adds a (%rip) suffix on 64 bits only; for immediate memory references */
+#define _ASM_RIP(x)	__ASM_SEL_RAW(x, x (__ASM_REGPFX rip))
+
 #ifndef __x86_64__
 /* 32 bit */
 
@@ -122,28 +127,19 @@
 
 #ifdef __KERNEL__
 
+# include <asm/extable_fixup_types.h>
+
 /* Exception table entry */
 #ifdef __ASSEMBLY__
-# define _ASM_EXTABLE_HANDLE(from, to, handler)			\
+
+# define _ASM_EXTABLE_TYPE(from, to, type)			\
 	.pushsection "__ex_table","a" ;				\
 	.balign 4 ;						\
 	.long (from) - . ;					\
 	.long (to) - . ;					\
-	.long (handler) - . ;					\
+	.long type ;						\
 	.popsection
 
-# define _ASM_EXTABLE(from, to)					\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_default)
-
-# define _ASM_EXTABLE_UA(from, to)				\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_uaccess)
-
-# define _ASM_EXTABLE_CPY(from, to)				\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_copy)
-
-# define _ASM_EXTABLE_FAULT(from, to)				\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_fault)
-
 # ifdef CONFIG_KPROBES
 #  define _ASM_NOKPROBE(entry)					\
 	.pushsection "_kprobe_blacklist","aw" ;			\
@@ -155,26 +151,51 @@
 # endif
 
 #else /* ! __ASSEMBLY__ */
-# define _EXPAND_EXTABLE_HANDLE(x) #x
-# define _ASM_EXTABLE_HANDLE(from, to, handler)			\
+
+# define DEFINE_EXTABLE_TYPE_REG \
+	".macro extable_type_reg type:req reg:req\n"						\
+	".set .Lfound, 0\n"									\
+	".set .Lregnr, 0\n"									\
+	".irp rs,rax,rcx,rdx,rbx,rsp,rbp,rsi,rdi,r8,r9,r10,r11,r12,r13,r14,r15\n"		\
+	".ifc \\reg, %%\\rs\n"									\
+	".set .Lfound, .Lfound+1\n"								\
+	".long \\type + (.Lregnr << 8)\n"							\
+	".endif\n"										\
+	".set .Lregnr, .Lregnr+1\n"								\
+	".endr\n"										\
+	".set .Lregnr, 0\n"									\
+	".irp rs,eax,ecx,edx,ebx,esp,ebp,esi,edi,r8d,r9d,r10d,r11d,r12d,r13d,r14d,r15d\n"	\
+	".ifc \\reg, %%\\rs\n"									\
+	".set .Lfound, .Lfound+1\n"								\
+	".long \\type + (.Lregnr << 8)\n"							\
+	".endif\n"										\
+	".set .Lregnr, .Lregnr+1\n"								\
+	".endr\n"										\
+	".if (.Lfound != 1)\n"									\
+	".error \"extable_type_reg: bad register argument\"\n"					\
+	".endif\n"										\
+	".endm\n"
+
+# define UNDEFINE_EXTABLE_TYPE_REG \
+	".purgem extable_type_reg\n"
+
+# define _ASM_EXTABLE_TYPE(from, to, type)			\
 	" .pushsection \"__ex_table\",\"a\"\n"			\
 	" .balign 4\n"						\
 	" .long (" #from ") - .\n"				\
 	" .long (" #to ") - .\n"				\
-	" .long (" _EXPAND_EXTABLE_HANDLE(handler) ") - .\n"	\
+	" .long " __stringify(type) " \n"			\
 	" .popsection\n"
 
-# define _ASM_EXTABLE(from, to)					\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_default)
-
-# define _ASM_EXTABLE_UA(from, to)				\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_uaccess)
-
-# define _ASM_EXTABLE_CPY(from, to)				\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_copy)
-
-# define _ASM_EXTABLE_FAULT(from, to)				\
-	_ASM_EXTABLE_HANDLE(from, to, ex_handler_fault)
+# define _ASM_EXTABLE_TYPE_REG(from, to, type, reg)				\
+	" .pushsection \"__ex_table\",\"a\"\n"					\
+	" .balign 4\n"								\
+	" .long (" #from ") - .\n"						\
+	" .long (" #to ") - .\n"						\
+	DEFINE_EXTABLE_TYPE_REG							\
+	"extable_type_reg reg=" __stringify(reg) ", type=" __stringify(type) " \n"\
+	UNDEFINE_EXTABLE_TYPE_REG						\
+	" .popsection\n"
 
 /* For C file, we already have NOKPROBE_SYMBOL macro */
 
@@ -188,6 +209,17 @@
 #define ASM_CALL_CONSTRAINT "+r" (current_stack_pointer)
 #endif /* __ASSEMBLY__ */
 
-#endif /* __KERNEL__ */
+#define _ASM_EXTABLE(from, to)					\
+	_ASM_EXTABLE_TYPE(from, to, EX_TYPE_DEFAULT)
 
+#define _ASM_EXTABLE_UA(from, to)				\
+	_ASM_EXTABLE_TYPE(from, to, EX_TYPE_UACCESS)
+
+#define _ASM_EXTABLE_CPY(from, to)				\
+	_ASM_EXTABLE_TYPE(from, to, EX_TYPE_COPY)
+
+#define _ASM_EXTABLE_FAULT(from, to)				\
+	_ASM_EXTABLE_TYPE(from, to, EX_TYPE_FAULT)
+
+#endif /* __KERNEL__ */
 #endif /* _ASM_X86_ASM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/barrier.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/barrier.h
@@ -81,22 +81,4 @@
 
 #include <asm-generic/barrier.h>
 
-/*
- * Make previous memory operations globally visible before
- * a WRMSR.
- *
- * MFENCE makes writes visible, but only affects load/store
- * instructions.  WRMSR is unfortunately not a load/store
- * instruction and is unaffected by MFENCE.  The LFENCE ensures
- * that the WRMSR is not reordered.
- *
- * Most WRMSRs are full serializing instructions themselves and
- * do not require this barrier.  This is only required for the
- * IA32_TSC_DEADLINE and X2APIC MSRs.
- */
-static inline void weak_wrmsr_fence(void)
-{
-	asm volatile("mfence; lfence" : : : "memory");
-}
-
 #endif /* _ASM_X86_BARRIER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/boot.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/boot.h
@@ -40,23 +40,40 @@
 #ifdef CONFIG_X86_64
 # define BOOT_STACK_SIZE	0x4000
 
+/*
+ * Used by decompressor's startup_32() to allocate page tables for identity
+ * mapping of the 4G of RAM in 4-level paging mode:
+ * - 1 level4 table;
+ * - 1 level3 table;
+ * - 4 level2 table that maps everything with 2M pages;
+ *
+ * The additional level5 table needed for 5-level paging is allocated from
+ * trampoline_32bit memory.
+ */
 # define BOOT_INIT_PGT_SIZE	(6*4096)
-# ifdef CONFIG_RANDOMIZE_BASE
+
 /*
- * Assuming all cross the 512GB boundary:
- * 1 page for level4
- * (2+2)*4 pages for kernel, param, cmd_line, and randomized kernel
- * 2 pages for first 2M (video RAM: CONFIG_X86_VERBOSE_BOOTUP).
- * Total is 19 pages.
+ * Total number of page tables kernel_add_identity_map() can allocate,
+ * including page tables consumed by startup_32().
+ *
+ * Worst-case scenario:
+ *  - 5-level paging needs 1 level5 table;
+ *  - KASLR needs to map kernel, boot_params, cmdline and randomized kernel,
+ *    assuming all of them cross 256T boundary:
+ *    + 4*2 level4 table;
+ *    + 4*2 level3 table;
+ *    + 4*2 level2 table;
+ *  - X86_VERBOSE_BOOTUP needs to map the first 2M (video RAM):
+ *    + 1 level4 table;
+ *    + 1 level3 table;
+ *    + 1 level2 table;
+ * Total: 28 tables
+ *
+ * Add 4 spare table in case decompressor touches anything beyond what is
+ * accounted above. Warn if it happens.
  */
-#  ifdef CONFIG_X86_VERBOSE_BOOTUP
-#   define BOOT_PGT_SIZE	(19*4096)
-#  else /* !CONFIG_X86_VERBOSE_BOOTUP */
-#   define BOOT_PGT_SIZE	(17*4096)
-#  endif
-# else /* !CONFIG_RANDOMIZE_BASE */
-#  define BOOT_PGT_SIZE		BOOT_INIT_PGT_SIZE
-# endif
+# define BOOT_PGT_SIZE_WARN	(28*4096)
+# define BOOT_PGT_SIZE		(32*4096)
 
 #else /* !CONFIG_X86_64 */
 # define BOOT_STACK_SIZE	0x1000
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/bug.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/bug.h
@@ -17,12 +17,12 @@
 #ifdef CONFIG_X86_32
 # define __BUG_REL(val)	".long " __stringify(val)
 #else
-# define __BUG_REL(val)	".long " __stringify(val) " - 2b"
+# define __BUG_REL(val)	".long " __stringify(val) " - ."
 #endif
 
 #ifdef CONFIG_DEBUG_BUGVERBOSE
 
-#define _BUG_FLAGS(ins, flags)						\
+#define _BUG_FLAGS(ins, flags, extra)					\
 do {									\
 	asm_inline volatile("1:\t" ins "\n"				\
 		     ".pushsection __bug_table,\"aw\"\n"		\
@@ -31,7 +31,8 @@
 		     "\t.word %c1"        "\t# bug_entry::line\n"	\
 		     "\t.word %c2"        "\t# bug_entry::flags\n"	\
 		     "\t.org 2b+%c3\n"					\
-		     ".popsection"					\
+		     ".popsection\n"					\
+		     extra						\
 		     : : "i" (__FILE__), "i" (__LINE__),		\
 			 "i" (flags),					\
 			 "i" (sizeof(struct bug_entry)));		\
@@ -39,14 +40,15 @@
 
 #else /* !CONFIG_DEBUG_BUGVERBOSE */
 
-#define _BUG_FLAGS(ins, flags)						\
+#define _BUG_FLAGS(ins, flags, extra)					\
 do {									\
 	asm_inline volatile("1:\t" ins "\n"				\
 		     ".pushsection __bug_table,\"aw\"\n"		\
 		     "2:\t" __BUG_REL(1b) "\t# bug_entry::bug_addr\n"	\
 		     "\t.word %c0"        "\t# bug_entry::flags\n"	\
 		     "\t.org 2b+%c1\n"					\
-		     ".popsection"					\
+		     ".popsection\n"					\
+		     extra						\
 		     : : "i" (flags),					\
 			 "i" (sizeof(struct bug_entry)));		\
 } while (0)
@@ -55,7 +57,7 @@
 
 #else
 
-#define _BUG_FLAGS(ins, flags)  asm volatile(ins)
+#define _BUG_FLAGS(ins, flags, extra)  asm volatile(ins)
 
 #endif /* CONFIG_GENERIC_BUG */
 
@@ -63,8 +65,8 @@
 #define BUG()							\
 do {								\
 	instrumentation_begin();				\
-	_BUG_FLAGS(ASM_UD2, 0);					\
-	unreachable();						\
+	_BUG_FLAGS(ASM_UD2, 0, "");				\
+	__builtin_unreachable();				\
 } while (0)
 
 /*
@@ -75,9 +77,9 @@
  */
 #define __WARN_FLAGS(flags)					\
 do {								\
+	__auto_type __flags = BUGFLAG_WARNING|(flags);		\
 	instrumentation_begin();				\
-	_BUG_FLAGS(ASM_UD2, BUGFLAG_WARNING|(flags));		\
-	annotate_reachable();					\
+	_BUG_FLAGS(ASM_UD2, __flags, ASM_REACHABLE);		\
 	instrumentation_end();					\
 } while (0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/bugs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/bugs.h
@@ -4,8 +4,6 @@
 
 #include <asm/processor.h>
 
-extern void check_bugs(void);
-
 #if defined(CONFIG_CPU_SUP_INTEL) && defined(CONFIG_X86_32)
 int ppro_with_ram_bug(void);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/compat.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/compat.h
@@ -28,15 +28,13 @@
 typedef __kernel_fsid_t	compat_fsid_t;
 
 struct compat_stat {
-	compat_dev_t	st_dev;
-	u16		__pad1;
+	u32		st_dev;
 	compat_ino_t	st_ino;
 	compat_mode_t	st_mode;
 	compat_nlink_t	st_nlink;
 	__compat_uid_t	st_uid;
 	__compat_gid_t	st_gid;
-	compat_dev_t	st_rdev;
-	u16		__pad2;
+	u32		st_rdev;
 	u32		st_size;
 	u32		st_blksize;
 	u32		st_blocks;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/cpu_device_id.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/cpu_device_id.h
@@ -3,6 +3,39 @@
 #define _ASM_X86_CPU_DEVICE_ID
 
 /*
+ * Can't use <linux/bitfield.h> because it generates expressions that
+ * cannot be used in structure initializers. Bitfield construction
+ * here must match the union in struct cpuinfo_86:
+ *	union {
+ *		struct {
+ *			__u8	x86_model;
+ *			__u8	x86;
+ *			__u8	x86_vendor;
+ *			__u8	x86_reserved;
+ *		};
+ *		__u32		x86_vfm;
+ *	};
+ */
+#define VFM_MODEL_BIT	0
+#define VFM_FAMILY_BIT	8
+#define VFM_VENDOR_BIT	16
+#define VFM_RSVD_BIT	24
+
+#define	VFM_MODEL_MASK	GENMASK(VFM_FAMILY_BIT - 1, VFM_MODEL_BIT)
+#define	VFM_FAMILY_MASK	GENMASK(VFM_VENDOR_BIT - 1, VFM_FAMILY_BIT)
+#define	VFM_VENDOR_MASK	GENMASK(VFM_RSVD_BIT - 1, VFM_VENDOR_BIT)
+
+#define VFM_MODEL(vfm)	(((vfm) & VFM_MODEL_MASK) >> VFM_MODEL_BIT)
+#define VFM_FAMILY(vfm)	(((vfm) & VFM_FAMILY_MASK) >> VFM_FAMILY_BIT)
+#define VFM_VENDOR(vfm)	(((vfm) & VFM_VENDOR_MASK) >> VFM_VENDOR_BIT)
+
+#define	VFM_MAKE(_vendor, _family, _model) (	\
+	((_model) << VFM_MODEL_BIT) |		\
+	((_family) << VFM_FAMILY_BIT) |		\
+	((_vendor) << VFM_VENDOR_BIT)		\
+)
+
+/*
  * Declare drivers belonging to specific x86 CPUs
  * Similar in spirit to pci_device_id and related PCI functions
  *
@@ -20,6 +53,9 @@
 #define X86_CENTAUR_FAM6_C7_D		0xd
 #define X86_CENTAUR_FAM6_NANO		0xf
 
+/* x86_cpu_id::flags */
+#define X86_CPU_ID_FLAG_ENTRY_VALID	BIT(0)
+
 #define X86_STEPPINGS(mins, maxs)    GENMASK(maxs, mins)
 /**
  * X86_MATCH_VENDOR_FAM_MODEL_STEPPINGS_FEATURE - Base macro for CPU matching
@@ -46,6 +82,18 @@
 	.model		= _model,					\
 	.steppings	= _steppings,					\
 	.feature	= _feature,					\
+	.flags		= X86_CPU_ID_FLAG_ENTRY_VALID,			\
+	.driver_data	= (unsigned long) _data				\
+}
+
+#define X86_MATCH_VENDORID_FAM_MODEL_STEPPINGS_FEATURE(_vendor, _family, _model, \
+						    _steppings, _feature, _data) { \
+	.vendor		= _vendor,					\
+	.family		= _family,					\
+	.model		= _model,					\
+	.steppings	= _steppings,					\
+	.feature	= _feature,					\
+	.flags		= X86_CPU_ID_FLAG_ENTRY_VALID,			\
 	.driver_data	= (unsigned long) _data				\
 }
 
@@ -164,6 +212,56 @@
 	X86_MATCH_VENDOR_FAM_MODEL_STEPPINGS_FEATURE(INTEL, 6, INTEL_FAM6_##model, \
 						     steppings, X86_FEATURE_ANY, data)
 
+/**
+ * X86_MATCH_VFM - Match encoded vendor/family/model
+ * @vfm:	Encoded 8-bits each for vendor, family, model
+ * @data:	Driver specific data or NULL. The internal storage
+ *		format is unsigned long. The supplied value, pointer
+ *		etc. is cast to unsigned long internally.
+ *
+ * Stepping and feature are set to wildcards
+ */
+#define X86_MATCH_VFM(vfm, data)			\
+	X86_MATCH_VENDORID_FAM_MODEL_STEPPINGS_FEATURE(	\
+		VFM_VENDOR(vfm),			\
+		VFM_FAMILY(vfm),			\
+		VFM_MODEL(vfm),				\
+		X86_STEPPING_ANY, X86_FEATURE_ANY, data)
+
+/**
+ * X86_MATCH_VFM_STEPPINGS - Match encoded vendor/family/model/stepping
+ * @vfm:	Encoded 8-bits each for vendor, family, model
+ * @steppings:	Bitmask of steppings to match
+ * @data:	Driver specific data or NULL. The internal storage
+ *		format is unsigned long. The supplied value, pointer
+ *		etc. is cast to unsigned long internally.
+ *
+ * feature is set to wildcard
+ */
+#define X86_MATCH_VFM_STEPPINGS(vfm, steppings, data)	\
+	X86_MATCH_VENDORID_FAM_MODEL_STEPPINGS_FEATURE(	\
+		VFM_VENDOR(vfm),			\
+		VFM_FAMILY(vfm),			\
+		VFM_MODEL(vfm),				\
+		steppings, X86_FEATURE_ANY, data)
+
+/**
+ * X86_MATCH_VFM_FEATURE - Match encoded vendor/family/model/feature
+ * @vfm:	Encoded 8-bits each for vendor, family, model
+ * @feature:	A X86_FEATURE bit
+ * @data:	Driver specific data or NULL. The internal storage
+ *		format is unsigned long. The supplied value, pointer
+ *		etc. is cast to unsigned long internally.
+ *
+ * Steppings is set to wildcard
+ */
+#define X86_MATCH_VFM_FEATURE(vfm, feature, data)	\
+	X86_MATCH_VENDORID_FAM_MODEL_STEPPINGS_FEATURE(	\
+		VFM_VENDOR(vfm),			\
+		VFM_FAMILY(vfm),			\
+		VFM_MODEL(vfm),				\
+		X86_STEPPING_ANY, feature, data)
+
 /*
  * Match specific microcode revisions.
  *
@@ -188,6 +286,14 @@
 	.x86_model		= (model),			\
 	.x86_stepping		= (stepping),			\
 	.x86_microcode_rev	= (revision),			\
+}
+
+#define AMD_CPU_DESC(fam, model, stepping, revision) {		\
+	.x86_family		= (fam),			\
+	.x86_vendor		= X86_VENDOR_AMD,		\
+	.x86_model		= (model),			\
+	.x86_stepping		= (stepping),			\
+	.x86_microcode_rev	= (revision),			\
 }
 
 extern const struct x86_cpu_id *x86_match_cpu(const struct x86_cpu_id *match);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/cpu_entry_area.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/cpu_entry_area.h
@@ -10,6 +10,12 @@
 
 #ifdef CONFIG_X86_64
 
+#ifdef CONFIG_AMD_MEM_ENCRYPT
+#define VC_EXCEPTION_STKSZ	EXCEPTION_STKSZ
+#else
+#define VC_EXCEPTION_STKSZ	0
+#endif
+
 /* Macro to enforce the same ordering and stack sizes */
 #define ESTACKS_MEMBERS(guardsize, optional_stack_size)		\
 	char	DF_stack_guard[guardsize];			\
@@ -28,7 +34,7 @@
 
 /* The exception stacks' physical storage. No guard pages required */
 struct exception_stacks {
-	ESTACKS_MEMBERS(0, 0)
+	ESTACKS_MEMBERS(0, VC_EXCEPTION_STKSZ)
 };
 
 /* The effective cpu entry area mapping with guard pages. */
@@ -124,10 +130,6 @@
 };
 
 #define CPU_ENTRY_AREA_SIZE		(sizeof(struct cpu_entry_area))
-#define CPU_ENTRY_AREA_ARRAY_SIZE	(CPU_ENTRY_AREA_SIZE * NR_CPUS)
-
-/* Total size includes the readonly IDT mapping page as well: */
-#define CPU_ENTRY_AREA_TOTAL_SIZE	(CPU_ENTRY_AREA_ARRAY_SIZE + PAGE_SIZE)
 
 DECLARE_PER_CPU(struct cpu_entry_area *, cpu_entry_area);
 DECLARE_PER_CPU(struct cea_exception_stacks *, cea_exception_stacks);
@@ -137,7 +139,7 @@
 
 extern struct cpu_entry_area *get_cpu_entry_area(int cpu);
 
-static inline struct entry_stack *cpu_entry_stack(int cpu)
+static __always_inline struct entry_stack *cpu_entry_stack(int cpu)
 {
 	return &get_cpu_entry_area(cpu)->entry_stack_page.stack;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/cpufeature.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/cpufeature.h
@@ -32,6 +32,9 @@
 	CPUID_8000_0007_EBX,
 	CPUID_7_EDX,
 	CPUID_8000_001F_EAX,
+	CPUID_8000_0021_EAX,
+	CPUID_LNX_5,
+	NR_CPUID_WORDS,
 };
 
 #ifdef CONFIG_X86_FEATURE_NAMES
@@ -51,7 +54,7 @@
 extern const char * const x86_bug_flags[NBUGINTS*32];
 
 #define test_cpu_cap(c, bit)						\
-	 test_bit(bit, (unsigned long *)((c)->x86_capability))
+	 arch_test_bit(bit, (unsigned long *)((c)->x86_capability))
 
 /*
  * There are 32 bits/features in each mask word.  The high bits
@@ -91,8 +94,10 @@
 	   CHECK_BIT_IN_MASK_WORD(REQUIRED_MASK, 17, feature_bit) ||	\
 	   CHECK_BIT_IN_MASK_WORD(REQUIRED_MASK, 18, feature_bit) ||	\
 	   CHECK_BIT_IN_MASK_WORD(REQUIRED_MASK, 19, feature_bit) ||	\
+	   CHECK_BIT_IN_MASK_WORD(REQUIRED_MASK, 20, feature_bit) ||	\
+	   CHECK_BIT_IN_MASK_WORD(REQUIRED_MASK, 21, feature_bit) ||	\
 	   REQUIRED_MASK_CHECK					  ||	\
-	   BUILD_BUG_ON_ZERO(NCAPINTS != 20))
+	   BUILD_BUG_ON_ZERO(NCAPINTS != 22))
 
 #define DISABLED_MASK_BIT_SET(feature_bit)				\
 	 ( CHECK_BIT_IN_MASK_WORD(DISABLED_MASK,  0, feature_bit) ||	\
@@ -115,8 +120,10 @@
 	   CHECK_BIT_IN_MASK_WORD(DISABLED_MASK, 17, feature_bit) ||	\
 	   CHECK_BIT_IN_MASK_WORD(DISABLED_MASK, 18, feature_bit) ||	\
 	   CHECK_BIT_IN_MASK_WORD(DISABLED_MASK, 19, feature_bit) ||	\
+	   CHECK_BIT_IN_MASK_WORD(DISABLED_MASK, 20, feature_bit) ||	\
+	   CHECK_BIT_IN_MASK_WORD(DISABLED_MASK, 21, feature_bit) ||	\
 	   DISABLED_MASK_CHECK					  ||	\
-	   BUILD_BUG_ON_ZERO(NCAPINTS != 20))
+	   BUILD_BUG_ON_ZERO(NCAPINTS != 22))
 
 #define cpu_has(c, bit)							\
 	(__builtin_constant_p(bit) && REQUIRED_MASK_BIT_SET(bit) ? 1 :	\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/cpufeatures.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/cpufeatures.h
@@ -13,8 +13,8 @@
 /*
  * Defines x86 CPU feature bits
  */
-#define NCAPINTS			20	   /* N 32-bit words worth of info */
-#define NBUGINTS			1	   /* N 32-bit bug flags */
+#define NCAPINTS			22	   /* N 32-bit words worth of info */
+#define NBUGINTS			2	   /* N 32-bit bug flags */
 
 /*
  * Note: If the comment begins with a quoted string, that string is used
@@ -203,8 +203,8 @@
 #define X86_FEATURE_PROC_FEEDBACK	( 7*32+ 9) /* AMD ProcFeedbackInterface */
 /* FREE!                                ( 7*32+10) */
 #define X86_FEATURE_PTI			( 7*32+11) /* Kernel Page Table Isolation enabled */
-#define X86_FEATURE_RETPOLINE		( 7*32+12) /* "" Generic Retpoline mitigation for Spectre variant 2 */
-#define X86_FEATURE_RETPOLINE_AMD	( 7*32+13) /* "" AMD Retpoline mitigation for Spectre variant 2 */
+#define X86_FEATURE_KERNEL_IBRS		( 7*32+12) /* "" Set/clear IBRS on kernel entry/exit */
+#define X86_FEATURE_RSB_VMEXIT		( 7*32+13) /* "" Fill RSB on VM-Exit */
 #define X86_FEATURE_INTEL_PPIN		( 7*32+14) /* Intel Processor Inventory Number */
 #define X86_FEATURE_CDP_L2		( 7*32+15) /* Code and Data Prioritization L2 */
 #define X86_FEATURE_MSR_SPEC_CTRL	( 7*32+16) /* "" MSR SPEC_CTRL is implemented */
@@ -217,7 +217,7 @@
 #define X86_FEATURE_SPEC_STORE_BYPASS_DISABLE	( 7*32+23) /* "" Disable Speculative Store Bypass. */
 #define X86_FEATURE_LS_CFG_SSBD		( 7*32+24)  /* "" AMD SSBD implementation via LS_CFG MSR */
 #define X86_FEATURE_IBRS		( 7*32+25) /* Indirect Branch Restricted Speculation */
-#define X86_FEATURE_IBPB		( 7*32+26) /* Indirect Branch Prediction Barrier */
+#define X86_FEATURE_IBPB		( 7*32+26) /* "ibpb" Indirect Branch Prediction Barrier without a guaranteed RSB flush */
 #define X86_FEATURE_STIBP		( 7*32+27) /* Single Thread Indirect Branch Predictors */
 #define X86_FEATURE_ZEN			( 7*32+28) /* "" CPU is AMD family 0x17 or above (Zen) */
 #define X86_FEATURE_L1TF_PTEINV		( 7*32+29) /* "" L1TF workaround PTE inversion */
@@ -277,6 +277,7 @@
 #define X86_FEATURE_XSAVEC		(10*32+ 1) /* XSAVEC instruction */
 #define X86_FEATURE_XGETBV1		(10*32+ 2) /* XGETBV with ECX = 1 instruction */
 #define X86_FEATURE_XSAVES		(10*32+ 3) /* XSAVES/XRSTORS instructions */
+#define X86_FEATURE_XFD			(10*32+ 4) /* "" eXtended Feature Disabling */
 
 /*
  * Extended auxiliary flags: Linux defined - for features scattered in various
@@ -294,6 +295,22 @@
 #define X86_FEATURE_PER_THREAD_MBA	(11*32+ 7) /* "" Per-thread Memory Bandwidth Allocation */
 #define X86_FEATURE_SGX1		(11*32+ 8) /* "" Basic SGX */
 #define X86_FEATURE_SGX2		(11*32+ 9) /* "" SGX Enclave Dynamic Memory Management (EDMM) */
+#define X86_FEATURE_ENTRY_IBPB		(11*32+10) /* "" Issue an IBPB on kernel entry */
+#define X86_FEATURE_RRSBA_CTRL		(11*32+11) /* "" RET prediction control */
+#define X86_FEATURE_RETPOLINE		(11*32+12) /* "" Generic Retpoline mitigation for Spectre variant 2 */
+#define X86_FEATURE_RETPOLINE_LFENCE	(11*32+13) /* "" Use LFENCE for Spectre variant 2 */
+#define X86_FEATURE_RETHUNK		(11*32+14) /* "" Use REturn THUNK */
+#define X86_FEATURE_UNRET		(11*32+15) /* "" AMD BTB untrain return */
+#define X86_FEATURE_USE_IBPB_FW		(11*32+16) /* "" Use IBPB during runtime firmware calls */
+#define X86_FEATURE_RSB_VMEXIT_LITE	(11*32+17) /* "" Fill RSB on VM exit when EIBRS is enabled */
+#define X86_FEATURE_CLEAR_CPU_BUF	(11*32+18) /* "" Clear CPU buffers using VERW */
+
+#define X86_FEATURE_MSR_TSX_CTRL	(11*32+20) /* "" MSR IA32_TSX_CTRL (Intel) implemented */
+
+#define X86_FEATURE_SRSO		(11*32+24) /* "" AMD BTB untrain RETs */
+#define X86_FEATURE_SRSO_ALIAS		(11*32+25) /* "" AMD BTB untrain RETs through aliasing */
+#define X86_FEATURE_IBPB_ON_VMEXIT	(11*32+26) /* "" Issue an IBPB only on VMEXIT */
+#define X86_FEATURE_APIC_MSRS_FENCE	(11*32+27) /* "" IA32_TSC_DEADLINE and X2APIC MSRs need fencing */
 
 /* Intel-defined CPU features, CPUID level 0x00000007:1 (EAX), word 12 */
 #define X86_FEATURE_AVX_VNNI		(12*32+ 4) /* AVX VNNI instructions */
@@ -313,6 +330,9 @@
 #define X86_FEATURE_AMD_SSBD		(13*32+24) /* "" Speculative Store Bypass Disable */
 #define X86_FEATURE_VIRT_SSBD		(13*32+25) /* Virtualized Speculative Store Bypass Disable */
 #define X86_FEATURE_AMD_SSB_NO		(13*32+26) /* "" Speculative Store Bypass is fixed in hardware. */
+#define X86_FEATURE_CPPC		(13*32+27) /* Collaborative Processor Performance Control */
+#define X86_FEATURE_BTC_NO		(13*32+29) /* "" Not vulnerable to Branch Type Confusion */
+#define X86_FEATURE_AMD_IBPB_RET	(13*32+30) /* "" IBPB clears return address predictor */
 
 /* Thermal and Power Management Leaf, CPUID level 0x00000006 (EAX), word 14 */
 #define X86_FEATURE_DTHERM		(14*32+ 0) /* Digital Thermal Sensor */
@@ -385,7 +405,10 @@
 #define X86_FEATURE_TSXLDTRK		(18*32+16) /* TSX Suspend Load Address Tracking */
 #define X86_FEATURE_PCONFIG		(18*32+18) /* Intel PCONFIG */
 #define X86_FEATURE_ARCH_LBR		(18*32+19) /* Intel ARCH LBR */
+#define X86_FEATURE_AMX_BF16		(18*32+22) /* AMX bf16 Support */
 #define X86_FEATURE_AVX512_FP16		(18*32+23) /* AVX512 FP16 */
+#define X86_FEATURE_AMX_TILE		(18*32+24) /* AMX tile Support */
+#define X86_FEATURE_AMX_INT8		(18*32+25) /* AMX int8 Support */
 #define X86_FEATURE_SPEC_CTRL		(18*32+26) /* "" Speculation Control (IBRS + IBPB) */
 #define X86_FEATURE_INTEL_STIBP		(18*32+27) /* "" Single Thread Indirect Branch Predictors */
 #define X86_FEATURE_FLUSH_L1D		(18*32+28) /* Flush L1D cache */
@@ -400,6 +423,22 @@
 #define X86_FEATURE_SEV_ES		(19*32+ 3) /* AMD Secure Encrypted Virtualization - Encrypted State */
 #define X86_FEATURE_SME_COHERENT	(19*32+10) /* "" AMD hardware-enforced cache coherency */
 
+#define X86_FEATURE_AUTOIBRS		(20*32+ 8) /* "" Automatic IBRS */
+#define X86_FEATURE_SBPB		(20*32+27) /* "" Selective Branch Prediction Barrier */
+#define X86_FEATURE_IBPB_BRTYPE		(20*32+28) /* "" MSR_PRED_CMD[IBPB] flushes all branch type predictions */
+#define X86_FEATURE_SRSO_NO		(20*32+29) /* "" CPU is not affected by SRSO */
+
+/*
+ * Extended auxiliary flags: Linux defined - for features scattered in various
+ * CPUID levels like 0x80000022, etc and Linux defined features.
+ *
+ * Reuse free bits when adding new feature flags!
+ */
+#define X86_FEATURE_CLEAR_BHB_LOOP	(21*32+ 1) /* "" Clear branch history at syscall entry using SW loop */
+#define X86_FEATURE_BHI_CTRL		(21*32+ 2) /* "" BHI_DIS_S HW control available */
+#define X86_FEATURE_CLEAR_BHB_HW	(21*32+ 3) /* "" BHI_DIS_S HW control enabled */
+#define X86_FEATURE_CLEAR_BHB_LOOP_ON_VMEXIT (21*32+ 4) /* "" Clear branch history at vmexit using SW loop */
+
 /*
  * BUG word(s)
  */
@@ -436,5 +475,17 @@
 #define X86_BUG_TAA			X86_BUG(22) /* CPU is affected by TSX Async Abort(TAA) */
 #define X86_BUG_ITLB_MULTIHIT		X86_BUG(23) /* CPU may incur MCE during certain page attribute changes */
 #define X86_BUG_SRBDS			X86_BUG(24) /* CPU may leak RNG bits if not mitigated */
-
+#define X86_BUG_MMIO_STALE_DATA		X86_BUG(25) /* CPU is affected by Processor MMIO Stale Data vulnerabilities */
+#define X86_BUG_MMIO_UNKNOWN		X86_BUG(26) /* CPU is too old and its MMIO Stale Data status is unknown */
+#define X86_BUG_RETBLEED		X86_BUG(27) /* CPU is affected by RETBleed */
+#define X86_BUG_EIBRS_PBRSB		X86_BUG(28) /* EIBRS is vulnerable to Post Barrier RSB Predictions */
+#define X86_BUG_SMT_RSB			X86_BUG(29) /* CPU is vulnerable to Cross-Thread Return Address Predictions */
+#define X86_BUG_GDS			X86_BUG(30) /* CPU is affected by Gather Data Sampling */
+
+/* BUG word 2 */
+#define X86_BUG_SRSO			X86_BUG(1*32 + 0) /* AMD SRSO bug */
+#define X86_BUG_DIV0			X86_BUG(1*32 + 1) /* AMD DIV0 speculation bug */
+#define X86_BUG_RFDS			X86_BUG(1*32 + 2) /* CPU is vulnerable to Register File Data Sampling */
+#define X86_BUG_BHI			X86_BUG(1*32 + 3) /* CPU is affected by Branch History Injection */
+#define X86_BUG_IBPB_NO_RET		X86_BUG(1*32 + 4) /* "ibpb_no_ret" IBPB omits return target predictions */
 #endif /* _ASM_X86_CPUFEATURES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/debugreg.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/debugreg.h
@@ -39,7 +39,20 @@
 		asm("mov %%db6, %0" :"=r" (val));
 		break;
 	case 7:
-		asm("mov %%db7, %0" :"=r" (val));
+		/*
+		 * Apply __FORCE_ORDER to DR7 reads to forbid re-ordering them
+		 * with other code.
+		 *
+		 * This is needed because a DR7 access can cause a #VC exception
+		 * when running under SEV-ES. Taking a #VC exception is not a
+		 * safe thing to do just anywhere in the entry code and
+		 * re-ordering might place the access into an unsafe location.
+		 *
+		 * This happened in the NMI handler, where the DR7 read was
+		 * re-ordered to happen before the call to sev_es_ist_enter(),
+		 * causing stack recursion.
+		 */
+		asm volatile("mov %%db7, %0" : "=r" (val) : __FORCE_ORDER);
 		break;
 	default:
 		BUG();
@@ -66,7 +79,16 @@
 		asm("mov %0, %%db6"	::"r" (value));
 		break;
 	case 7:
-		asm("mov %0, %%db7"	::"r" (value));
+		/*
+		 * Apply __FORCE_ORDER to DR7 writes to forbid re-ordering them
+		 * with other code.
+		 *
+		 * While is didn't happen with a DR7 write (see the DR7 read
+		 * comment above which explains where it happened), add the
+		 * __FORCE_ORDER here too to avoid similar problems in the
+		 * future.
+		 */
+		asm volatile("mov %0, %%db7"	::"r" (value), __FORCE_ORDER);
 		break;
 	default:
 		BUG();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/disabled-features.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/disabled-features.h
@@ -56,6 +56,25 @@
 # define DISABLE_PTI		(1 << (X86_FEATURE_PTI & 31))
 #endif
 
+#ifdef CONFIG_RETPOLINE
+# define DISABLE_RETPOLINE	0
+#else
+# define DISABLE_RETPOLINE	((1 << (X86_FEATURE_RETPOLINE & 31)) | \
+				 (1 << (X86_FEATURE_RETPOLINE_LFENCE & 31)))
+#endif
+
+#ifdef CONFIG_RETHUNK
+# define DISABLE_RETHUNK	0
+#else
+# define DISABLE_RETHUNK	(1 << (X86_FEATURE_RETHUNK & 31))
+#endif
+
+#ifdef CONFIG_CPU_UNRET_ENTRY
+# define DISABLE_UNRET		0
+#else
+# define DISABLE_UNRET		(1 << (X86_FEATURE_UNRET & 31))
+#endif
+
 /* Force disable because it's broken beyond repair */
 #define DISABLE_ENQCMD		(1 << (X86_FEATURE_ENQCMD & 31))
 
@@ -79,7 +98,7 @@
 #define DISABLED_MASK8	0
 #define DISABLED_MASK9	(DISABLE_SMAP|DISABLE_SGX)
 #define DISABLED_MASK10	0
-#define DISABLED_MASK11	0
+#define DISABLED_MASK11	(DISABLE_RETPOLINE|DISABLE_RETHUNK|DISABLE_UNRET)
 #define DISABLED_MASK12	0
 #define DISABLED_MASK13	0
 #define DISABLED_MASK14	0
@@ -89,6 +108,8 @@
 #define DISABLED_MASK17	0
 #define DISABLED_MASK18	0
 #define DISABLED_MASK19	0
-#define DISABLED_MASK_CHECK BUILD_BUG_ON_ZERO(NCAPINTS != 20)
+#define DISABLED_MASK20	0
+#define DISABLED_MASK21	0
+#define DISABLED_MASK_CHECK BUILD_BUG_ON_ZERO(NCAPINTS != 22)
 
 #endif /* _ASM_X86_DISABLED_FEATURES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/efi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/efi.h
@@ -197,8 +197,6 @@
 
 extern void parse_efi_setup(u64 phys_addr, u32 data_len);
 
-extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
-
 extern void efi_thunk_runtime_setup(void);
 efi_status_t efi_set_virtual_address_map(unsigned long memory_map_size,
 					 unsigned long descriptor_size,
@@ -388,6 +386,17 @@
 }
 #endif
 
+extern int __init efi_memmap_alloc(unsigned int num_entries,
+				   struct efi_memory_map_data *data);
+extern void __efi_memmap_free(u64 phys, unsigned long size,
+			      unsigned long flags);
+
+extern int __init efi_memmap_install(struct efi_memory_map_data *data);
+extern int __init efi_memmap_split_count(efi_memory_desc_t *md,
+					 struct range *range);
+extern void __init efi_memmap_insert(struct efi_memory_map *old_memmap,
+				     void *buf, struct efi_mem_range *mem);
+
 #define arch_ima_efi_boot_mode	\
 	({ extern struct boot_params boot_params; boot_params.secure_boot; })
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/entry-common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/entry-common.h
@@ -91,7 +91,7 @@
 
 static __always_inline void arch_exit_to_user_mode(void)
 {
-	mds_user_clear_cpu_buffers();
+	amd_clear_divider();
 }
 #define arch_exit_to_user_mode arch_exit_to_user_mode
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/extable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/extable.h
@@ -1,12 +1,18 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 #ifndef _ASM_X86_EXTABLE_H
 #define _ASM_X86_EXTABLE_H
+
+#include <asm/extable_fixup_types.h>
+
 /*
- * The exception table consists of triples of addresses relative to the
- * exception table entry itself. The first address is of an instruction
- * that is allowed to fault, the second is the target at which the program
- * should continue. The third is a handler function to deal with the fault
- * caused by the instruction in the first field.
+ * The exception table consists of two addresses relative to the
+ * exception table entry itself and a type selector field.
+ *
+ * The first address is of an instruction that is allowed to fault, the
+ * second is the target at which the program should continue.
+ *
+ * The type entry is used by fixup_exception() to select the handler to
+ * deal with the fault caused by the instruction in the first field.
  *
  * All the routines below use bits of fixup code that are out of line
  * with the main instruction path.  This means when everything is well,
@@ -15,7 +21,7 @@
  */
 
 struct exception_table_entry {
-	int insn, fixup, handler;
+	int insn, fixup, data;
 };
 struct pt_regs;
 
@@ -25,21 +31,27 @@
 	do {							\
 		(a)->fixup = (b)->fixup + (delta);		\
 		(b)->fixup = (tmp).fixup - (delta);		\
-		(a)->handler = (b)->handler + (delta);		\
-		(b)->handler = (tmp).handler - (delta);		\
+		(a)->data = (b)->data;				\
+		(b)->data = (tmp).data;				\
 	} while (0)
 
-enum handler_type {
-	EX_HANDLER_NONE,
-	EX_HANDLER_FAULT,
-	EX_HANDLER_UACCESS,
-	EX_HANDLER_OTHER
-};
-
 extern int fixup_exception(struct pt_regs *regs, int trapnr,
 			   unsigned long error_code, unsigned long fault_addr);
 extern int fixup_bug(struct pt_regs *regs, int trapnr);
-extern enum handler_type ex_get_fault_handler_type(unsigned long ip);
+extern int ex_get_fixup_type(unsigned long ip);
 extern void early_fixup_exception(struct pt_regs *regs, int trapnr);
 
+#ifdef CONFIG_X86_MCE
+extern void ex_handler_msr_mce(struct pt_regs *regs, bool wrmsr);
+#else
+static inline void ex_handler_msr_mce(struct pt_regs *regs, bool wrmsr) { }
+#endif
+
+#if defined(CONFIG_BPF_JIT) && defined(CONFIG_X86_64)
+bool ex_handler_bpf(const struct exception_table_entry *x, struct pt_regs *regs);
+#else
+static inline bool ex_handler_bpf(const struct exception_table_entry *x,
+				  struct pt_regs *regs) { return false; }
+#endif
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/extable_fixup_types.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/extable_fixup_types.h
@@ -0,0 +1,58 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_X86_EXTABLE_FIXUP_TYPES_H
+#define _ASM_X86_EXTABLE_FIXUP_TYPES_H
+
+/*
+ * Our IMM is signed, as such it must live at the top end of the word. Also,
+ * since C99 hex constants are of ambigious type, force cast the mask to 'int'
+ * so that FIELD_GET() will DTRT and sign extend the value when it extracts it.
+ */
+#define EX_DATA_TYPE_MASK		((int)0x000000FF)
+#define EX_DATA_REG_MASK		((int)0x00000F00)
+#define EX_DATA_FLAG_MASK		((int)0x0000F000)
+#define EX_DATA_IMM_MASK		((int)0xFFFF0000)
+
+#define EX_DATA_REG_SHIFT		8
+#define EX_DATA_FLAG_SHIFT		12
+#define EX_DATA_IMM_SHIFT		16
+
+#define EX_DATA_REG(reg)		((reg) << EX_DATA_REG_SHIFT)
+#define EX_DATA_FLAG(flag)		((flag) << EX_DATA_FLAG_SHIFT)
+#define EX_DATA_IMM(imm)		((imm) << EX_DATA_IMM_SHIFT)
+
+/* segment regs */
+#define EX_REG_DS			EX_DATA_REG(8)
+#define EX_REG_ES			EX_DATA_REG(9)
+#define EX_REG_FS			EX_DATA_REG(10)
+#define EX_REG_GS			EX_DATA_REG(11)
+
+/* flags */
+#define EX_FLAG_CLEAR_AX		EX_DATA_FLAG(1)
+#define EX_FLAG_CLEAR_DX		EX_DATA_FLAG(2)
+#define EX_FLAG_CLEAR_AX_DX		EX_DATA_FLAG(3)
+
+/* types */
+#define	EX_TYPE_NONE			 0
+#define	EX_TYPE_DEFAULT			 1
+#define	EX_TYPE_FAULT			 2
+#define	EX_TYPE_UACCESS			 3
+#define	EX_TYPE_COPY			 4
+#define	EX_TYPE_CLEAR_FS		 5
+#define	EX_TYPE_FPU_RESTORE		 6
+#define	EX_TYPE_BPF			 7
+#define	EX_TYPE_WRMSR			 8
+#define	EX_TYPE_RDMSR			 9
+#define	EX_TYPE_WRMSR_SAFE		10 /* reg := -EIO */
+#define	EX_TYPE_RDMSR_SAFE		11 /* reg := -EIO */
+#define	EX_TYPE_WRMSR_IN_MCE		12
+#define	EX_TYPE_RDMSR_IN_MCE		13
+#define	EX_TYPE_DEFAULT_MCE_SAFE	14
+#define	EX_TYPE_FAULT_MCE_SAFE		15
+
+#define	EX_TYPE_POP_REG			16 /* sp += sizeof(long) */
+#define EX_TYPE_POP_ZERO		(EX_TYPE_POP_REG | EX_DATA_IMM(0))
+
+#define	EX_TYPE_IMM_REG			17 /* reg := (long)imm */
+#define	EX_TYPE_EFAULT_REG		(EX_TYPE_IMM_REG | EX_DATA_IMM(-EFAULT))
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/api.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/api.h
@@ -12,6 +12,8 @@
 #define _ASM_X86_FPU_API_H
 #include <linux/bottom_half.h>
 
+#include <asm/fpu/types.h>
+
 /*
  * Use kernel_fpu_begin/end() if you intend to use FPU in kernel context. It
  * disables preemption so be careful if you intend to use it for long periods
@@ -48,9 +50,9 @@
 }
 
 /*
- * Use fpregs_lock() while editing CPU's FPU registers or fpu->state.
+ * Use fpregs_lock() while editing CPU's FPU registers or fpu->fpstate.
  * A context switch will (and softirq might) save CPU's FPU registers to
- * fpu->state and set TIF_NEED_FPU_LOAD leaving CPU's FPU registers in
+ * fpu->fpstate.regs and set TIF_NEED_FPU_LOAD leaving CPU's FPU registers in
  * a random state.
  *
  * local_bh_disable() protects against both preemption and soft interrupts
@@ -108,4 +110,57 @@
 
 static inline void update_pasid(void) { }
 
+/* Trap handling */
+extern int  fpu__exception_code(struct fpu *fpu, int trap_nr);
+extern void fpu_sync_fpstate(struct fpu *fpu);
+extern void fpu_reset_from_exception_fixup(void);
+
+/* Boot, hotplug and resume */
+extern void fpu__init_cpu(void);
+extern void fpu__init_system(void);
+extern void fpu__init_check_bugs(void);
+extern void fpu__resume_cpu(void);
+
+#ifdef CONFIG_MATH_EMULATION
+extern void fpstate_init_soft(struct swregs_state *soft);
+#else
+static inline void fpstate_init_soft(struct swregs_state *soft) {}
+#endif
+
+/* State tracking */
+DECLARE_PER_CPU(struct fpu *, fpu_fpregs_owner_ctx);
+
+/* Process cleanup */
+#ifdef CONFIG_X86_64
+extern void fpstate_free(struct fpu *fpu);
+#else
+static inline void fpstate_free(struct fpu *fpu) { }
+#endif
+
+/* fpstate-related functions which are exported to KVM */
+extern void fpstate_clear_xstate_component(struct fpstate *fps, unsigned int xfeature);
+
+/* KVM specific functions */
+extern bool fpu_alloc_guest_fpstate(struct fpu_guest *gfpu);
+extern void fpu_free_guest_fpstate(struct fpu_guest *gfpu);
+extern int fpu_swap_kvm_fpstate(struct fpu_guest *gfpu, bool enter_guest);
+
+extern void fpu_copy_guest_fpstate_to_uabi(struct fpu_guest *gfpu, void *buf,
+					   unsigned int size, u64 xfeatures, u32 pkru);
+extern int fpu_copy_uabi_to_guest_fpstate(struct fpu_guest *gfpu, const void *buf, u64 xcr0, u32 *vpkru);
+
+static inline void fpstate_set_confidential(struct fpu_guest *gfpu)
+{
+	gfpu->fpstate->is_confidential = true;
+}
+
+static inline bool fpstate_is_confidential(struct fpu_guest *gfpu)
+{
+	return gfpu->fpstate->is_confidential;
+}
+
+/* prctl */
+struct task_struct;
+extern long fpu_xstate_prctl(struct task_struct *tsk, int option, unsigned long arg2);
+
 #endif /* _ASM_X86_FPU_API_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/internal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/internal.h
@@ -1,540 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (C) 1994 Linus Torvalds
- *
- * Pentium III FXSR, SSE support
- * General FPU state handling cleanups
- *	Gareth Hughes <gareth@valinux.com>, May 2000
- * x86-64 work by Andi Kleen 2002
- */
-
-#ifndef _ASM_X86_FPU_INTERNAL_H
-#define _ASM_X86_FPU_INTERNAL_H
-
-#include <linux/compat.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/mm.h>
-
-#include <asm/user.h>
-#include <asm/fpu/api.h>
-#include <asm/fpu/xstate.h>
-#include <asm/fpu/xcr.h>
-#include <asm/cpufeature.h>
-#include <asm/trace/fpu.h>
-
-/*
- * High level FPU state handling functions:
- */
-extern int  fpu__restore_sig(void __user *buf, int ia32_frame);
-extern void fpu__drop(struct fpu *fpu);
-extern void fpu__clear_user_states(struct fpu *fpu);
-extern int  fpu__exception_code(struct fpu *fpu, int trap_nr);
-
-extern void fpu_sync_fpstate(struct fpu *fpu);
-
-/* Clone and exit operations */
-extern int  fpu_clone(struct task_struct *dst);
-extern void fpu_flush_thread(void);
-
-/*
- * Boot time FPU initialization functions:
- */
-extern void fpu__init_cpu(void);
-extern void fpu__init_system_xstate(void);
-extern void fpu__init_cpu_xstate(void);
-extern void fpu__init_system(struct cpuinfo_x86 *c);
-extern void fpu__init_check_bugs(void);
-extern void fpu__resume_cpu(void);
-
-/*
- * Debugging facility:
- */
-#ifdef CONFIG_X86_DEBUG_FPU
-# define WARN_ON_FPU(x) WARN_ON_ONCE(x)
-#else
-# define WARN_ON_FPU(x) ({ (void)(x); 0; })
-#endif
-
-/*
- * FPU related CPU feature flag helper routines:
- */
-static __always_inline __pure bool use_xsaveopt(void)
-{
-	return static_cpu_has(X86_FEATURE_XSAVEOPT);
-}
-
-static __always_inline __pure bool use_xsave(void)
-{
-	return static_cpu_has(X86_FEATURE_XSAVE);
-}
-
-static __always_inline __pure bool use_fxsr(void)
-{
-	return static_cpu_has(X86_FEATURE_FXSR);
-}
-
-/*
- * fpstate handling functions:
- */
-
-extern union fpregs_state init_fpstate;
-
-extern void fpstate_init(union fpregs_state *state);
-#ifdef CONFIG_MATH_EMULATION
-extern void fpstate_init_soft(struct swregs_state *soft);
-#else
-static inline void fpstate_init_soft(struct swregs_state *soft) {}
-#endif
-extern void save_fpregs_to_fpstate(struct fpu *fpu);
-
-/* Returns 0 or the negated trap number, which results in -EFAULT for #PF */
-#define user_insn(insn, output, input...)				\
-({									\
-	int err;							\
-									\
-	might_fault();							\
-									\
-	asm volatile(ASM_STAC "\n"					\
-		     "1: " #insn "\n"					\
-		     "2: " ASM_CLAC "\n"				\
-		     ".section .fixup,\"ax\"\n"				\
-		     "3:  negl %%eax\n"					\
-		     "    jmp  2b\n"					\
-		     ".previous\n"					\
-		     _ASM_EXTABLE_FAULT(1b, 3b)				\
-		     : [err] "=a" (err), output				\
-		     : "0"(0), input);					\
-	err;								\
-})
-
-#define kernel_insn_err(insn, output, input...)				\
-({									\
-	int err;							\
-	asm volatile("1:" #insn "\n\t"					\
-		     "2:\n"						\
-		     ".section .fixup,\"ax\"\n"				\
-		     "3:  movl $-1,%[err]\n"				\
-		     "    jmp  2b\n"					\
-		     ".previous\n"					\
-		     _ASM_EXTABLE(1b, 3b)				\
-		     : [err] "=r" (err), output				\
-		     : "0"(0), input);					\
-	err;								\
-})
-
-#define kernel_insn(insn, output, input...)				\
-	asm volatile("1:" #insn "\n\t"					\
-		     "2:\n"						\
-		     _ASM_EXTABLE_HANDLE(1b, 2b, ex_handler_fprestore)	\
-		     : output : input)
-
-static inline int fnsave_to_user_sigframe(struct fregs_state __user *fx)
-{
-	return user_insn(fnsave %[fx]; fwait,  [fx] "=m" (*fx), "m" (*fx));
-}
-
-static inline int fxsave_to_user_sigframe(struct fxregs_state __user *fx)
-{
-	if (IS_ENABLED(CONFIG_X86_32))
-		return user_insn(fxsave %[fx], [fx] "=m" (*fx), "m" (*fx));
-	else
-		return user_insn(fxsaveq %[fx], [fx] "=m" (*fx), "m" (*fx));
-
-}
-
-static inline void fxrstor(struct fxregs_state *fx)
-{
-	if (IS_ENABLED(CONFIG_X86_32))
-		kernel_insn(fxrstor %[fx], "=m" (*fx), [fx] "m" (*fx));
-	else
-		kernel_insn(fxrstorq %[fx], "=m" (*fx), [fx] "m" (*fx));
-}
-
-static inline int fxrstor_safe(struct fxregs_state *fx)
-{
-	if (IS_ENABLED(CONFIG_X86_32))
-		return kernel_insn_err(fxrstor %[fx], "=m" (*fx), [fx] "m" (*fx));
-	else
-		return kernel_insn_err(fxrstorq %[fx], "=m" (*fx), [fx] "m" (*fx));
-}
-
-static inline int fxrstor_from_user_sigframe(struct fxregs_state __user *fx)
-{
-	if (IS_ENABLED(CONFIG_X86_32))
-		return user_insn(fxrstor %[fx], "=m" (*fx), [fx] "m" (*fx));
-	else
-		return user_insn(fxrstorq %[fx], "=m" (*fx), [fx] "m" (*fx));
-}
-
-static inline void frstor(struct fregs_state *fx)
-{
-	kernel_insn(frstor %[fx], "=m" (*fx), [fx] "m" (*fx));
-}
-
-static inline int frstor_safe(struct fregs_state *fx)
-{
-	return kernel_insn_err(frstor %[fx], "=m" (*fx), [fx] "m" (*fx));
-}
-
-static inline int frstor_from_user_sigframe(struct fregs_state __user *fx)
-{
-	return user_insn(frstor %[fx], "=m" (*fx), [fx] "m" (*fx));
-}
-
-static inline void fxsave(struct fxregs_state *fx)
-{
-	if (IS_ENABLED(CONFIG_X86_32))
-		asm volatile( "fxsave %[fx]" : [fx] "=m" (*fx));
-	else
-		asm volatile("fxsaveq %[fx]" : [fx] "=m" (*fx));
-}
-
-/* These macros all use (%edi)/(%rdi) as the single memory argument. */
-#define XSAVE		".byte " REX_PREFIX "0x0f,0xae,0x27"
-#define XSAVEOPT	".byte " REX_PREFIX "0x0f,0xae,0x37"
-#define XSAVES		".byte " REX_PREFIX "0x0f,0xc7,0x2f"
-#define XRSTOR		".byte " REX_PREFIX "0x0f,0xae,0x2f"
-#define XRSTORS		".byte " REX_PREFIX "0x0f,0xc7,0x1f"
-
-/*
- * After this @err contains 0 on success or the negated trap number when
- * the operation raises an exception. For faults this results in -EFAULT.
- */
-#define XSTATE_OP(op, st, lmask, hmask, err)				\
-	asm volatile("1:" op "\n\t"					\
-		     "xor %[err], %[err]\n"				\
-		     "2:\n\t"						\
-		     ".pushsection .fixup,\"ax\"\n\t"			\
-		     "3: negl %%eax\n\t"				\
-		     "jmp 2b\n\t"					\
-		     ".popsection\n\t"					\
-		     _ASM_EXTABLE_FAULT(1b, 3b)				\
-		     : [err] "=a" (err)					\
-		     : "D" (st), "m" (*st), "a" (lmask), "d" (hmask)	\
-		     : "memory")
-
-/*
- * If XSAVES is enabled, it replaces XSAVEOPT because it supports a compact
- * format and supervisor states in addition to modified optimization in
- * XSAVEOPT.
- *
- * Otherwise, if XSAVEOPT is enabled, XSAVEOPT replaces XSAVE because XSAVEOPT
- * supports modified optimization which is not supported by XSAVE.
- *
- * We use XSAVE as a fallback.
- *
- * The 661 label is defined in the ALTERNATIVE* macros as the address of the
- * original instruction which gets replaced. We need to use it here as the
- * address of the instruction where we might get an exception at.
- */
-#define XSTATE_XSAVE(st, lmask, hmask, err)				\
-	asm volatile(ALTERNATIVE_2(XSAVE,				\
-				   XSAVEOPT, X86_FEATURE_XSAVEOPT,	\
-				   XSAVES,   X86_FEATURE_XSAVES)	\
-		     "\n"						\
-		     "xor %[err], %[err]\n"				\
-		     "3:\n"						\
-		     ".pushsection .fixup,\"ax\"\n"			\
-		     "4: movl $-2, %[err]\n"				\
-		     "jmp 3b\n"						\
-		     ".popsection\n"					\
-		     _ASM_EXTABLE(661b, 4b)				\
-		     : [err] "=r" (err)					\
-		     : "D" (st), "m" (*st), "a" (lmask), "d" (hmask)	\
-		     : "memory")
-
-/*
- * Use XRSTORS to restore context if it is enabled. XRSTORS supports compact
- * XSAVE area format.
- */
-#define XSTATE_XRESTORE(st, lmask, hmask)				\
-	asm volatile(ALTERNATIVE(XRSTOR,				\
-				 XRSTORS, X86_FEATURE_XSAVES)		\
-		     "\n"						\
-		     "3:\n"						\
-		     _ASM_EXTABLE_HANDLE(661b, 3b, ex_handler_fprestore)\
-		     :							\
-		     : "D" (st), "m" (*st), "a" (lmask), "d" (hmask)	\
-		     : "memory")
-
-/*
- * This function is called only during boot time when x86 caps are not set
- * up and alternative can not be used yet.
- */
-static inline void os_xrstor_booting(struct xregs_state *xstate)
-{
-	u64 mask = xfeatures_mask_fpstate();
-	u32 lmask = mask;
-	u32 hmask = mask >> 32;
-	int err;
-
-	WARN_ON(system_state != SYSTEM_BOOTING);
-
-	if (boot_cpu_has(X86_FEATURE_XSAVES))
-		XSTATE_OP(XRSTORS, xstate, lmask, hmask, err);
-	else
-		XSTATE_OP(XRSTOR, xstate, lmask, hmask, err);
-
-	/*
-	 * We should never fault when copying from a kernel buffer, and the FPU
-	 * state we set at boot time should be valid.
-	 */
-	WARN_ON_FPU(err);
-}
-
-/*
- * Save processor xstate to xsave area.
- *
- * Uses either XSAVE or XSAVEOPT or XSAVES depending on the CPU features
- * and command line options. The choice is permanent until the next reboot.
- */
-static inline void os_xsave(struct xregs_state *xstate)
-{
-	u64 mask = xfeatures_mask_all;
-	u32 lmask = mask;
-	u32 hmask = mask >> 32;
-	int err;
-
-	WARN_ON_FPU(!alternatives_patched);
-
-	XSTATE_XSAVE(xstate, lmask, hmask, err);
-
-	/* We should never fault when copying to a kernel buffer: */
-	WARN_ON_FPU(err);
-}
-
-/*
- * Restore processor xstate from xsave area.
- *
- * Uses XRSTORS when XSAVES is used, XRSTOR otherwise.
- */
-static inline void os_xrstor(struct xregs_state *xstate, u64 mask)
-{
-	u32 lmask = mask;
-	u32 hmask = mask >> 32;
-
-	XSTATE_XRESTORE(xstate, lmask, hmask);
-}
-
-/*
- * Save xstate to user space xsave area.
- *
- * We don't use modified optimization because xrstor/xrstors might track
- * a different application.
- *
- * We don't use compacted format xsave area for
- * backward compatibility for old applications which don't understand
- * compacted format of xsave area.
- */
-static inline int xsave_to_user_sigframe(struct xregs_state __user *buf)
-{
-	/*
-	 * Include the features which are not xsaved/rstored by the kernel
-	 * internally, e.g. PKRU. That's user space ABI and also required
-	 * to allow the signal handler to modify PKRU.
-	 */
-	u64 mask = xfeatures_mask_uabi();
-	u32 lmask = mask;
-	u32 hmask = mask >> 32;
-	int err;
-
-	/*
-	 * Clear the xsave header first, so that reserved fields are
-	 * initialized to zero.
-	 */
-	err = __clear_user(&buf->header, sizeof(buf->header));
-	if (unlikely(err))
-		return -EFAULT;
-
-	stac();
-	XSTATE_OP(XSAVE, buf, lmask, hmask, err);
-	clac();
-
-	return err;
-}
-
-/*
- * Restore xstate from user space xsave area.
- */
-static inline int xrstor_from_user_sigframe(struct xregs_state __user *buf, u64 mask)
-{
-	struct xregs_state *xstate = ((__force struct xregs_state *)buf);
-	u32 lmask = mask;
-	u32 hmask = mask >> 32;
-	int err;
-
-	stac();
-	XSTATE_OP(XRSTOR, xstate, lmask, hmask, err);
-	clac();
-
-	return err;
-}
-
-/*
- * Restore xstate from kernel space xsave area, return an error code instead of
- * an exception.
- */
-static inline int os_xrstor_safe(struct xregs_state *xstate, u64 mask)
-{
-	u32 lmask = mask;
-	u32 hmask = mask >> 32;
-	int err;
-
-	if (cpu_feature_enabled(X86_FEATURE_XSAVES))
-		XSTATE_OP(XRSTORS, xstate, lmask, hmask, err);
-	else
-		XSTATE_OP(XRSTOR, xstate, lmask, hmask, err);
-
-	return err;
-}
-
-extern void __restore_fpregs_from_fpstate(union fpregs_state *fpstate, u64 mask);
-
-static inline void restore_fpregs_from_fpstate(union fpregs_state *fpstate)
-{
-	__restore_fpregs_from_fpstate(fpstate, xfeatures_mask_fpstate());
-}
-
-extern int copy_fpstate_to_sigframe(void __user *buf, void __user *fp, int size);
-
-/*
- * FPU context switch related helper methods:
- */
-
-DECLARE_PER_CPU(struct fpu *, fpu_fpregs_owner_ctx);
-
-/*
- * The in-register FPU state for an FPU context on a CPU is assumed to be
- * valid if the fpu->last_cpu matches the CPU, and the fpu_fpregs_owner_ctx
- * matches the FPU.
- *
- * If the FPU register state is valid, the kernel can skip restoring the
- * FPU state from memory.
- *
- * Any code that clobbers the FPU registers or updates the in-memory
- * FPU state for a task MUST let the rest of the kernel know that the
- * FPU registers are no longer valid for this task.
- *
- * Either one of these invalidation functions is enough. Invalidate
- * a resource you control: CPU if using the CPU for something else
- * (with preemption disabled), FPU for the current task, or a task that
- * is prevented from running by the current task.
- */
-static inline void __cpu_invalidate_fpregs_state(void)
-{
-	__this_cpu_write(fpu_fpregs_owner_ctx, NULL);
-}
-
-static inline void __fpu_invalidate_fpregs_state(struct fpu *fpu)
-{
-	fpu->last_cpu = -1;
-}
-
-static inline int fpregs_state_valid(struct fpu *fpu, unsigned int cpu)
-{
-	return fpu == this_cpu_read(fpu_fpregs_owner_ctx) && cpu == fpu->last_cpu;
-}
-
-/*
- * These generally need preemption protection to work,
- * do try to avoid using these on their own:
- */
-static inline void fpregs_deactivate(struct fpu *fpu)
-{
-	this_cpu_write(fpu_fpregs_owner_ctx, NULL);
-	trace_x86_fpu_regs_deactivated(fpu);
-}
-
-static inline void fpregs_activate(struct fpu *fpu)
-{
-	this_cpu_write(fpu_fpregs_owner_ctx, fpu);
-	trace_x86_fpu_regs_activated(fpu);
-}
-
-/* Internal helper for switch_fpu_return() and signal frame setup */
-static inline void fpregs_restore_userregs(void)
-{
-	struct fpu *fpu = &current->thread.fpu;
-	int cpu = smp_processor_id();
-
-	if (WARN_ON_ONCE(current->flags & PF_KTHREAD))
-		return;
-
-	if (!fpregs_state_valid(fpu, cpu)) {
-		u64 mask;
-
-		/*
-		 * This restores _all_ xstate which has not been
-		 * established yet.
-		 *
-		 * If PKRU is enabled, then the PKRU value is already
-		 * correct because it was either set in switch_to() or in
-		 * flush_thread(). So it is excluded because it might be
-		 * not up to date in current->thread.fpu.xsave state.
-		 */
-		mask = xfeatures_mask_restore_user() |
-			xfeatures_mask_supervisor();
-		__restore_fpregs_from_fpstate(&fpu->state, mask);
-
-		fpregs_activate(fpu);
-		fpu->last_cpu = cpu;
-	}
-	clear_thread_flag(TIF_NEED_FPU_LOAD);
-}
-
-/*
- * FPU state switching for scheduling.
- *
- * This is a two-stage process:
- *
- *  - switch_fpu_prepare() saves the old state.
- *    This is done within the context of the old process.
- *
- *  - switch_fpu_finish() sets TIF_NEED_FPU_LOAD; the floating point state
- *    will get loaded on return to userspace, or when the kernel needs it.
- *
- * If TIF_NEED_FPU_LOAD is cleared then the CPU's FPU registers
- * are saved in the current thread's FPU register state.
- *
- * If TIF_NEED_FPU_LOAD is set then CPU's FPU registers may not
- * hold current()'s FPU registers. It is required to load the
- * registers before returning to userland or using the content
- * otherwise.
- *
- * The FPU context is only stored/restored for a user task and
- * PF_KTHREAD is used to distinguish between kernel and user threads.
- */
-static inline void switch_fpu_prepare(struct fpu *old_fpu, int cpu)
-{
-	if (static_cpu_has(X86_FEATURE_FPU) && !(current->flags & PF_KTHREAD)) {
-		save_fpregs_to_fpstate(old_fpu);
-		/*
-		 * The save operation preserved register state, so the
-		 * fpu_fpregs_owner_ctx is still @old_fpu. Store the
-		 * current CPU number in @old_fpu, so the next return
-		 * to user space can avoid the FPU register restore
-		 * when is returns on the same CPU and still owns the
-		 * context.
-		 */
-		old_fpu->last_cpu = cpu;
-
-		trace_x86_fpu_regs_deactivated(old_fpu);
-	}
-}
-
-/*
- * Misc helper functions:
- */
-
-/*
- * Delay loading of the complete FPU state until the return to userland.
- * PKRU is handled separately.
- */
-static inline void switch_fpu_finish(struct fpu *new_fpu)
-{
-	if (cpu_feature_enabled(X86_FEATURE_FPU))
-		set_thread_flag(TIF_NEED_FPU_LOAD);
-}
-
-#endif /* _ASM_X86_FPU_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/sched.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/sched.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_X86_FPU_SCHED_H
+#define _ASM_X86_FPU_SCHED_H
+
+#include <linux/sched.h>
+
+#include <asm/cpufeature.h>
+#include <asm/fpu/types.h>
+
+#include <asm/trace/fpu.h>
+
+extern void save_fpregs_to_fpstate(struct fpu *fpu);
+extern void fpu__drop(struct fpu *fpu);
+extern int  fpu_clone(struct task_struct *dst, unsigned long clone_flags);
+extern void fpu_flush_thread(void);
+
+/*
+ * FPU state switching for scheduling.
+ *
+ * This is a two-stage process:
+ *
+ *  - switch_fpu_prepare() saves the old state.
+ *    This is done within the context of the old process.
+ *
+ *  - switch_fpu_finish() sets TIF_NEED_FPU_LOAD; the floating point state
+ *    will get loaded on return to userspace, or when the kernel needs it.
+ *
+ * If TIF_NEED_FPU_LOAD is cleared then the CPU's FPU registers
+ * are saved in the current thread's FPU register state.
+ *
+ * If TIF_NEED_FPU_LOAD is set then CPU's FPU registers may not
+ * hold current()'s FPU registers. It is required to load the
+ * registers before returning to userland or using the content
+ * otherwise.
+ *
+ * The FPU context is only stored/restored for a user task and
+ * PF_KTHREAD is used to distinguish between kernel and user threads.
+ */
+static inline void switch_fpu_prepare(struct fpu *old_fpu, int cpu)
+{
+	if (cpu_feature_enabled(X86_FEATURE_FPU) &&
+	    !(current->flags & PF_KTHREAD)) {
+		save_fpregs_to_fpstate(old_fpu);
+		/*
+		 * The save operation preserved register state, so the
+		 * fpu_fpregs_owner_ctx is still @old_fpu. Store the
+		 * current CPU number in @old_fpu, so the next return
+		 * to user space can avoid the FPU register restore
+		 * when is returns on the same CPU and still owns the
+		 * context.
+		 */
+		old_fpu->last_cpu = cpu;
+
+		trace_x86_fpu_regs_deactivated(old_fpu);
+	}
+}
+
+/*
+ * Delay loading of the complete FPU state until the return to userland.
+ * PKRU is handled separately.
+ */
+static inline void switch_fpu_finish(void)
+{
+	if (cpu_feature_enabled(X86_FEATURE_FPU))
+		set_thread_flag(TIF_NEED_FPU_LOAD);
+}
+
+#endif /* _ASM_X86_FPU_SCHED_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/signal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/signal.h
@@ -5,6 +5,11 @@
 #ifndef _ASM_X86_FPU_SIGNAL_H
 #define _ASM_X86_FPU_SIGNAL_H
 
+#include <linux/compat.h>
+#include <linux/user.h>
+
+#include <asm/fpu/types.h>
+
 #ifdef CONFIG_X86_64
 # include <uapi/asm/sigcontext.h>
 # include <asm/user32.h>
@@ -31,6 +36,12 @@
 
 unsigned long fpu__get_fpstate_size(void);
 
-extern void fpu__init_prepare_fx_sw_frame(void);
+extern bool copy_fpstate_to_sigframe(void __user *buf, void __user *fp, int size);
+extern void fpu__clear_user_states(struct fpu *fpu);
+extern bool fpu__restore_sig(void __user *buf, int ia32_frame);
+
+extern void restore_fpregs_from_fpstate(struct fpstate *fpstate, u64 mask);
+
+extern bool copy_fpstate_to_sigframe(void __user *buf, void __user *fp, int size);
 
 #endif /* _ASM_X86_FPU_SIGNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/types.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/types.h
@@ -120,6 +120,9 @@
 	XFEATURE_RSRVD_COMP_13,
 	XFEATURE_RSRVD_COMP_14,
 	XFEATURE_LBR,
+	XFEATURE_RSRVD_COMP_16,
+	XFEATURE_XTILE_CFG,
+	XFEATURE_XTILE_DATA,
 
 	XFEATURE_MAX,
 };
@@ -136,12 +139,21 @@
 #define XFEATURE_MASK_PKRU		(1 << XFEATURE_PKRU)
 #define XFEATURE_MASK_PASID		(1 << XFEATURE_PASID)
 #define XFEATURE_MASK_LBR		(1 << XFEATURE_LBR)
+#define XFEATURE_MASK_XTILE_CFG		(1 << XFEATURE_XTILE_CFG)
+#define XFEATURE_MASK_XTILE_DATA	(1 << XFEATURE_XTILE_DATA)
 
 #define XFEATURE_MASK_FPSSE		(XFEATURE_MASK_FP | XFEATURE_MASK_SSE)
 #define XFEATURE_MASK_AVX512		(XFEATURE_MASK_OPMASK \
 					 | XFEATURE_MASK_ZMM_Hi256 \
 					 | XFEATURE_MASK_Hi16_ZMM)
 
+#ifdef CONFIG_X86_64
+# define XFEATURE_MASK_XTILE		(XFEATURE_MASK_XTILE_DATA \
+					 | XFEATURE_MASK_XTILE_CFG)
+#else
+# define XFEATURE_MASK_XTILE		(0)
+#endif
+
 #define FIRST_EXTENDED_XFEATURE	XFEATURE_YMM
 
 struct reg_128_bit {
@@ -153,6 +165,9 @@
 struct reg_512_bit {
 	u8	regbytes[512/8];
 };
+struct reg_1024_byte {
+	u8	regbytes[1024];
+};
 
 /*
  * State component 2:
@@ -255,6 +270,23 @@
 	u64 ler_to;
 	u64 ler_info;
 	struct lbr_entry		entries[];
+};
+
+/*
+ * State component 17: 64-byte tile configuration register.
+ */
+struct xtile_cfg {
+	u64				tcfg[8];
+} __packed;
+
+/*
+ * State component 18: 1KB tile data register.
+ * Each register represents 16 64-byte rows of the matrix
+ * data. But the number of registers depends on the actual
+ * implementation.
+ */
+struct xtile_data {
+	struct reg_1024_byte		tmm;
 } __packed;
 
 /*
@@ -309,6 +341,91 @@
 	u8 __padding[PAGE_SIZE];
 };
 
+struct fpstate {
+	/* @kernel_size: The size of the kernel register image */
+	unsigned int		size;
+
+	/* @user_size: The size in non-compacted UABI format */
+	unsigned int		user_size;
+
+	/* @xfeatures:		xfeatures for which the storage is sized */
+	u64			xfeatures;
+
+	/* @user_xfeatures:	xfeatures valid in UABI buffers */
+	u64			user_xfeatures;
+
+	/* @xfd:		xfeatures disabled to trap userspace use. */
+	u64			xfd;
+
+	/* @is_valloc:		Indicator for dynamically allocated state */
+	unsigned int		is_valloc	: 1;
+
+	/* @is_guest:		Indicator for guest state (KVM) */
+	unsigned int		is_guest	: 1;
+
+	/*
+	 * @is_confidential:	Indicator for KVM confidential mode.
+	 *			The FPU registers are restored by the
+	 *			vmentry firmware from encrypted guest
+	 *			memory. On vmexit the FPU registers are
+	 *			saved by firmware to encrypted guest memory
+	 *			and the registers are scrubbed before
+	 *			returning to the host. So there is no
+	 *			content which is worth saving and restoring.
+	 *			The fpstate has to be there so that
+	 *			preemption and softirq FPU usage works
+	 *			without special casing.
+	 */
+	unsigned int		is_confidential	: 1;
+
+	/* @in_use:		State is in use */
+	unsigned int		in_use		: 1;
+
+	/* @regs: The register state union for all supported formats */
+	union fpregs_state	regs;
+
+	/* @regs is dynamically sized! Don't add anything after @regs! */
+} __aligned(64);
+
+struct fpu_state_perm {
+	/*
+	 * @__state_perm:
+	 *
+	 * This bitmap indicates the permission for state components, which
+	 * are available to a thread group. The permission prctl() sets the
+	 * enabled state bits in thread_group_leader()->thread.fpu.
+	 *
+	 * All run time operations use the per thread information in the
+	 * currently active fpu.fpstate which contains the xfeature masks
+	 * and sizes for kernel and user space.
+	 *
+	 * This master permission field is only to be used when
+	 * task.fpu.fpstate based checks fail to validate whether the task
+	 * is allowed to expand it's xfeatures set which requires to
+	 * allocate a larger sized fpstate buffer.
+	 *
+	 * Do not access this field directly.  Use the provided helper
+	 * function. Unlocked access is possible for quick checks.
+	 */
+	u64				__state_perm;
+
+	/*
+	 * @__state_size:
+	 *
+	 * The size required for @__state_perm. Only valid to access
+	 * with sighand locked.
+	 */
+	unsigned int			__state_size;
+
+	/*
+	 * @__user_state_size:
+	 *
+	 * The size required for @__state_perm user part. Only valid to
+	 * access with sighand locked.
+	 */
+	unsigned int			__user_state_size;
+};
+
 /*
  * Highest level per task FPU state data structure that
  * contains the FPU register state plus various FPU
@@ -337,19 +454,107 @@
 	unsigned long			avx512_timestamp;
 
 	/*
-	 * @state:
+	 * @fpstate:
 	 *
-	 * In-memory copy of all FPU registers that we save/restore
-	 * over context switches. If the task is using the FPU then
-	 * the registers in the FPU are more recent than this state
-	 * copy. If the task context-switches away then they get
-	 * saved here and represent the FPU state.
+	 * Pointer to the active struct fpstate. Initialized to
+	 * point at @__fpstate below.
 	 */
-	union fpregs_state		state;
+	struct fpstate			*fpstate;
+
 	/*
-	 * WARNING: 'state' is dynamically-sized.  Do not put
+	 * @__task_fpstate:
+	 *
+	 * Pointer to an inactive struct fpstate. Initialized to NULL. Is
+	 * used only for KVM support to swap out the regular task fpstate.
+	 */
+	struct fpstate			*__task_fpstate;
+
+	/*
+	 * @perm:
+	 *
+	 * Permission related information
+	 */
+	struct fpu_state_perm		perm;
+
+	/*
+	 * @__fpstate:
+	 *
+	 * Initial in-memory storage for FPU registers which are saved in
+	 * context switch and when the kernel uses the FPU. The registers
+	 * are restored from this storage on return to user space if they
+	 * are not longer containing the tasks FPU register state.
+	 */
+	struct fpstate			__fpstate;
+	/*
+	 * WARNING: '__fpstate' is dynamically-sized.  Do not put
 	 * anything after it here.
 	 */
 };
 
+/*
+ * Guest pseudo FPU container
+ */
+struct fpu_guest {
+	/*
+	 * @fpstate:			Pointer to the allocated guest fpstate
+	 */
+	struct fpstate			*fpstate;
+};
+
+/*
+ * FPU state configuration data. Initialized at boot time. Read only after init.
+ */
+struct fpu_state_config {
+	/*
+	 * @max_size:
+	 *
+	 * The maximum size of the register state buffer. Includes all
+	 * supported features except independent managed features.
+	 */
+	unsigned int		max_size;
+
+	/*
+	 * @default_size:
+	 *
+	 * The default size of the register state buffer. Includes all
+	 * supported features except independent managed features and
+	 * features which have to be requested by user space before usage.
+	 */
+	unsigned int		default_size;
+
+	/*
+	 * @max_features:
+	 *
+	 * The maximum supported features bitmap. Does not include
+	 * independent managed features.
+	 */
+	u64 max_features;
+
+	/*
+	 * @default_features:
+	 *
+	 * The default supported features bitmap. Does not include
+	 * independent managed features and features which have to
+	 * be requested by user space before usage.
+	 */
+	u64 default_features;
+	/*
+	 * @legacy_features:
+	 *
+	 * Features which can be reported back to user space
+	 * even without XSAVE support, i.e. legacy features FP + SSE
+	 */
+	u64 legacy_features;
+	/*
+	 * @independent_features:
+	 *
+	 * Features that are supported by XSAVES, but not managed as part of
+	 * the FPU core, such as LBR
+	 */
+	u64 independent_features;
+};
+
+/* FPU state configuration information */
+extern struct fpu_state_config fpu_kernel_cfg, fpu_user_cfg;
+
 #endif /* _ASM_X86_FPU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/xcr.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/xcr.h
@@ -2,17 +2,6 @@
 #ifndef _ASM_X86_FPU_XCR_H
 #define _ASM_X86_FPU_XCR_H
 
-/*
- * MXCSR and XCR definitions:
- */
-
-static inline void ldmxcsr(u32 mxcsr)
-{
-	asm volatile("ldmxcsr %0" :: "m" (mxcsr));
-}
-
-extern unsigned int mxcsr_feature_mask;
-
 #define XCR_XFEATURE_ENABLED_MASK	0x00000000
 
 static inline u64 xgetbv(u32 index)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/fpu/xstate.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/fpu/xstate.h
@@ -14,6 +14,8 @@
 
 #define XSTATE_CPUID		0x0000000d
 
+#define TILE_CPUID		0x0000001d
+
 #define FXSAVE_SIZE	512
 
 #define XSAVE_HDR_SIZE	    64
@@ -33,7 +35,8 @@
 				      XFEATURE_MASK_Hi16_ZMM	 | \
 				      XFEATURE_MASK_PKRU | \
 				      XFEATURE_MASK_BNDREGS | \
-				      XFEATURE_MASK_BNDCSR)
+				      XFEATURE_MASK_BNDCSR | \
+				      XFEATURE_MASK_XTILE)
 
 /*
  * Features which are restored when returning to user space.
@@ -43,6 +46,9 @@
 #define XFEATURE_MASK_USER_RESTORE	\
 	(XFEATURE_MASK_USER_SUPPORTED & ~XFEATURE_MASK_PKRU)
 
+/* Features which are dynamically enabled for a process on request */
+#define XFEATURE_MASK_USER_DYNAMIC	XFEATURE_MASK_XTILE_DATA
+
 /* All currently supported supervisor features */
 #define XFEATURE_MASK_SUPERVISOR_SUPPORTED (XFEATURE_MASK_PASID)
 
@@ -78,78 +84,42 @@
 				      XFEATURE_MASK_INDEPENDENT | \
 				      XFEATURE_MASK_SUPERVISOR_UNSUPPORTED)
 
-#ifdef CONFIG_X86_64
-#define REX_PREFIX	"0x48, "
-#else
-#define REX_PREFIX
-#endif
-
-extern u64 xfeatures_mask_all;
-
-static inline u64 xfeatures_mask_supervisor(void)
-{
-	return xfeatures_mask_all & XFEATURE_MASK_SUPERVISOR_SUPPORTED;
-}
-
-/*
- * The xfeatures which are enabled in XCR0 and expected to be in ptrace
- * buffers and signal frames.
- */
-static inline u64 xfeatures_mask_uabi(void)
-{
-	return xfeatures_mask_all & XFEATURE_MASK_USER_SUPPORTED;
-}
-
-/*
- * The xfeatures which are restored by the kernel when returning to user
- * mode. This is not necessarily the same as xfeatures_mask_uabi() as the
- * kernel does not manage all XCR0 enabled features via xsave/xrstor as
- * some of them have to be switched eagerly on context switch and exec().
- */
-static inline u64 xfeatures_mask_restore_user(void)
-{
-	return xfeatures_mask_all & XFEATURE_MASK_USER_RESTORE;
-}
-
 /*
- * Like xfeatures_mask_restore_user() but additionally restors the
- * supported supervisor states.
+ * The feature mask required to restore FPU state:
+ * - All user states which are not eagerly switched in switch_to()/exec()
+ * - The suporvisor states
  */
-static inline u64 xfeatures_mask_fpstate(void)
-{
-	return xfeatures_mask_all & \
-		(XFEATURE_MASK_USER_RESTORE | XFEATURE_MASK_SUPERVISOR_SUPPORTED);
-}
-
-static inline u64 xfeatures_mask_independent(void)
-{
-	if (!boot_cpu_has(X86_FEATURE_ARCH_LBR))
-		return XFEATURE_MASK_INDEPENDENT & ~XFEATURE_MASK_LBR;
-
-	return XFEATURE_MASK_INDEPENDENT;
-}
+#define XFEATURE_MASK_FPSTATE	(XFEATURE_MASK_USER_RESTORE | \
+				 XFEATURE_MASK_SUPERVISOR_SUPPORTED)
 
 extern u64 xstate_fx_sw_bytes[USER_XSTATE_FX_SW_WORDS];
 
 extern void __init update_regset_xstate_info(unsigned int size,
 					     u64 xstate_mask);
 
-void *get_xsave_addr(struct xregs_state *xsave, int xfeature_nr);
 int xfeature_size(int xfeature_nr);
-int copy_uabi_from_kernel_to_xstate(struct xregs_state *xsave, const void *kbuf);
-int copy_sigframe_from_user_to_xstate(struct xregs_state *xsave, const void __user *ubuf);
 
 void xsaves(struct xregs_state *xsave, u64 mask);
 void xrstors(struct xregs_state *xsave, u64 mask);
 
-enum xstate_copy_mode {
-	XSTATE_COPY_FP,
-	XSTATE_COPY_FX,
-	XSTATE_COPY_XSAVE,
-};
-
-struct membuf;
-void copy_xstate_to_uabi_buf(struct membuf to, struct task_struct *tsk,
-			     enum xstate_copy_mode mode);
+int xfd_enable_feature(u64 xfd_err);
+
+#ifdef CONFIG_X86_64
+DECLARE_STATIC_KEY_FALSE(__fpu_state_size_dynamic);
+#endif
+
+#ifdef CONFIG_X86_64
+DECLARE_STATIC_KEY_FALSE(__fpu_state_size_dynamic);
+
+static __always_inline __pure bool fpu_state_size_dynamic(void)
+{
+	return static_branch_unlikely(&__fpu_state_size_dynamic);
+}
+#else
+static __always_inline __pure bool fpu_state_size_dynamic(void)
+{
+	return false;
+}
+#endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/futex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/futex.h
@@ -17,13 +17,9 @@
 	int oldval = 0, ret;					\
 	asm volatile("1:\t" insn "\n"				\
 		     "2:\n"					\
-		     "\t.section .fixup,\"ax\"\n"		\
-		     "3:\tmov\t%3, %1\n"			\
-		     "\tjmp\t2b\n"				\
-		     "\t.previous\n"				\
-		     _ASM_EXTABLE_UA(1b, 3b)			\
+		     _ASM_EXTABLE_TYPE_REG(1b, 2b, EX_TYPE_EFAULT_REG, %1) \
 		     : "=r" (oldval), "=r" (ret), "+m" (*uaddr)	\
-		     : "i" (-EFAULT), "0" (oparg), "1" (0));	\
+		     : "0" (oparg), "1" (0));	\
 	if (ret)						\
 		goto label;					\
 	*oval = oldval;						\
@@ -39,15 +35,11 @@
 		     "3:\t" LOCK_PREFIX "cmpxchgl %3, %2\n"	\
 		     "\tjnz\t2b\n"				\
 		     "4:\n"					\
-		     "\t.section .fixup,\"ax\"\n"		\
-		     "5:\tmov\t%5, %1\n"			\
-		     "\tjmp\t4b\n"				\
-		     "\t.previous\n"				\
-		     _ASM_EXTABLE_UA(1b, 5b)			\
-		     _ASM_EXTABLE_UA(3b, 5b)			\
+		     _ASM_EXTABLE_TYPE_REG(1b, 4b, EX_TYPE_EFAULT_REG, %1) \
+		     _ASM_EXTABLE_TYPE_REG(3b, 4b, EX_TYPE_EFAULT_REG, %1) \
 		     : "=&a" (oldval), "=&r" (ret),		\
 		       "+m" (*uaddr), "=&r" (tem)		\
-		     : "r" (oparg), "i" (-EFAULT), "1" (0));	\
+		     : "r" (oparg), "1" (0));			\
 	if (ret)						\
 		goto label;					\
 	*oval = oldval;						\
@@ -95,15 +87,11 @@
 	if (!user_access_begin(uaddr, sizeof(u32)))
 		return -EFAULT;
 	asm volatile("\n"
-		"1:\t" LOCK_PREFIX "cmpxchgl %4, %2\n"
+		"1:\t" LOCK_PREFIX "cmpxchgl %3, %2\n"
 		"2:\n"
-		"\t.section .fixup, \"ax\"\n"
-		"3:\tmov     %3, %0\n"
-		"\tjmp     2b\n"
-		"\t.previous\n"
-		_ASM_EXTABLE_UA(1b, 3b)
+		_ASM_EXTABLE_TYPE_REG(1b, 2b, EX_TYPE_EFAULT_REG, %0) \
 		: "+r" (ret), "=a" (oldval), "+m" (*uaddr)
-		: "i" (-EFAULT), "r" (newval), "1" (oldval)
+		: "r" (newval), "1" (oldval)
 		: "memory"
 	);
 	user_access_end();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/hardirq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/hardirq.h
@@ -62,7 +62,11 @@
 
 
 #if IS_ENABLED(CONFIG_KVM_INTEL)
-static inline void kvm_set_cpu_l1tf_flush_l1d(void)
+/*
+ * This function is called from noinstr interrupt contexts
+ * and must be inlined to not get instrumentation.
+ */
+static __always_inline void kvm_set_cpu_l1tf_flush_l1d(void)
 {
 	__this_cpu_write(irq_stat.kvm_cpu_l1tf_flush_l1d, 1);
 }
@@ -77,7 +81,7 @@
 	return __this_cpu_read(irq_stat.kvm_cpu_l1tf_flush_l1d);
 }
 #else /* !IS_ENABLED(CONFIG_KVM_INTEL) */
-static inline void kvm_set_cpu_l1tf_flush_l1d(void) { }
+static __always_inline void kvm_set_cpu_l1tf_flush_l1d(void) { }
 #endif /* IS_ENABLED(CONFIG_KVM_INTEL) */
 
 #endif /* _ASM_X86_HARDIRQ_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/hyperv-tlfs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/hyperv-tlfs.h
@@ -529,7 +529,7 @@
 	u64 guest_rip;
 
 	u32 hv_clean_fields;
-	u32 hv_padding_32;
+	u32 padding32_1;
 	u32 hv_synthetic_controls;
 	struct {
 		u32 nested_flush_hypercall:1;
@@ -537,7 +537,7 @@
 		u32 reserved:30;
 	}  __packed hv_enlightenments_control;
 	u32 hv_vp_id;
-
+	u32 padding32_2;
 	u64 hv_vm_id;
 	u64 partition_assist_page;
 	u64 padding64_4[4];
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/i8259.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/i8259.h
@@ -69,6 +69,8 @@
 	void (*make_irq)(unsigned int irq);
 };
 
+void legacy_pic_pcat_compat(void);
+
 extern struct legacy_pic *legacy_pic;
 extern struct legacy_pic null_legacy_pic;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/ia32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/ia32.h
@@ -68,6 +68,27 @@
 
 #endif
 
-#endif /* !CONFIG_IA32_SUPPORT */
+extern bool __ia32_enabled;
+
+static inline bool ia32_enabled(void)
+{
+	return __ia32_enabled;
+}
+
+static inline void ia32_disable(void)
+{
+	__ia32_enabled = false;
+}
+
+#else /* !CONFIG_IA32_EMULATION */
+
+static inline bool ia32_enabled(void)
+{
+	return IS_ENABLED(CONFIG_X86_32);
+}
+
+static inline void ia32_disable(void) {}
+
+#endif
 
 #endif /* _ASM_X86_IA32_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/idtentry.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/idtentry.h
@@ -11,15 +11,18 @@
 
 #include <asm/irq_stack.h>
 
+typedef void (*idtentry_t)(struct pt_regs *regs);
+
 /**
  * DECLARE_IDTENTRY - Declare functions for simple IDT entry points
  *		      No error code pushed by hardware
  * @vector:	Vector number (ignored for C)
  * @func:	Function name of the entry point
  *
- * Declares three functions:
+ * Declares four functions:
  * - The ASM entry point: asm_##func
  * - The XEN PV trap entry point: xen_##func (maybe unused)
+ * - The C handler called from the FRED event dispatcher (maybe unused)
  * - The C handler called from the ASM entry point
  *
  * Note: This is the C variant of DECLARE_IDTENTRY(). As the name says it
@@ -29,6 +32,7 @@
 #define DECLARE_IDTENTRY(vector, func)					\
 	asmlinkage void asm_##func(void);				\
 	asmlinkage void xen_asm_##func(void);				\
+	void fred_##func(struct pt_regs *regs);				\
 	__visible void func(struct pt_regs *regs)
 
 /**
@@ -136,6 +140,17 @@
 __visible noinstr void func(struct pt_regs *regs)
 
 /**
+ * DEFINE_FREDENTRY_RAW - Emit code for raw FRED entry points
+ * @func:	Function name of the entry point
+ *
+ * @func is called from the FRED event dispatcher with interrupts disabled.
+ *
+ * See @DEFINE_IDTENTRY_RAW for further details.
+ */
+#define DEFINE_FREDENTRY_RAW(func)					\
+noinstr void fred_##func(struct pt_regs *regs)
+
+/**
  * DECLARE_IDTENTRY_RAW_ERRORCODE - Declare functions for raw IDT entry points
  *				    Error code pushed by hardware
  * @vector:	Vector number (ignored for C)
@@ -195,8 +210,8 @@
 	irqentry_state_t state = irqentry_enter(regs);			\
 	u32 vector = (u32)(u8)error_code;				\
 									\
+	kvm_set_cpu_l1tf_flush_l1d();                                   \
 	instrumentation_begin();					\
-	kvm_set_cpu_l1tf_flush_l1d();					\
 	run_irq_on_irqstack_cond(__##func, regs, vector);		\
 	instrumentation_end();						\
 	irqentry_exit(regs, state);					\
@@ -231,17 +246,27 @@
 #define DEFINE_IDTENTRY_SYSVEC(func)					\
 static void __##func(struct pt_regs *regs);				\
 									\
+static __always_inline void instr_##func(struct pt_regs *regs)		\
+{									\
+	run_sysvec_on_irqstack_cond(__##func, regs);			\
+}									\
+									\
 __visible noinstr void func(struct pt_regs *regs)			\
 {									\
 	irqentry_state_t state = irqentry_enter(regs);			\
 									\
+	kvm_set_cpu_l1tf_flush_l1d();                                   \
 	instrumentation_begin();					\
-	kvm_set_cpu_l1tf_flush_l1d();					\
-	run_sysvec_on_irqstack_cond(__##func, regs);			\
+	instr_##func (regs);						\
 	instrumentation_end();						\
 	irqentry_exit(regs, state);					\
 }									\
 									\
+void fred_##func(struct pt_regs *regs)					\
+{									\
+	instr_##func (regs);						\
+}									\
+									\
 static noinline void __##func(struct pt_regs *regs)
 
 /**
@@ -258,19 +283,29 @@
 #define DEFINE_IDTENTRY_SYSVEC_SIMPLE(func)				\
 static __always_inline void __##func(struct pt_regs *regs);		\
 									\
+static __always_inline void instr_##func(struct pt_regs *regs)		\
+{									\
+	__irq_enter_raw();						\
+	__##func (regs);						\
+	__irq_exit_raw();						\
+}									\
+									\
 __visible noinstr void func(struct pt_regs *regs)			\
 {									\
 	irqentry_state_t state = irqentry_enter(regs);			\
 									\
+	kvm_set_cpu_l1tf_flush_l1d();                                   \
 	instrumentation_begin();					\
-	__irq_enter_raw();						\
-	kvm_set_cpu_l1tf_flush_l1d();					\
-	__##func (regs);						\
-	__irq_exit_raw();						\
+	instr_##func (regs);						\
 	instrumentation_end();						\
 	irqentry_exit(regs, state);					\
 }									\
 									\
+void fred_##func(struct pt_regs *regs)					\
+{									\
+	instr_##func (regs);						\
+}									\
+									\
 static __always_inline void __##func(struct pt_regs *regs)
 
 /**
@@ -408,15 +443,18 @@
 /* C-Code mapping */
 #define DECLARE_IDTENTRY_NMI		DECLARE_IDTENTRY_RAW
 #define DEFINE_IDTENTRY_NMI		DEFINE_IDTENTRY_RAW
+#define DEFINE_FREDENTRY_NMI		DEFINE_FREDENTRY_RAW
 
 #ifdef CONFIG_X86_64
 #define DECLARE_IDTENTRY_MCE		DECLARE_IDTENTRY_IST
 #define DEFINE_IDTENTRY_MCE		DEFINE_IDTENTRY_IST
 #define DEFINE_IDTENTRY_MCE_USER	DEFINE_IDTENTRY_NOIST
+#define DEFINE_FREDENTRY_MCE		DEFINE_FREDENTRY_RAW
 
 #define DECLARE_IDTENTRY_DEBUG		DECLARE_IDTENTRY_IST
 #define DEFINE_IDTENTRY_DEBUG		DEFINE_IDTENTRY_IST
 #define DEFINE_IDTENTRY_DEBUG_USER	DEFINE_IDTENTRY_NOIST
+#define DEFINE_FREDENTRY_DEBUG		DEFINE_FREDENTRY_RAW
 #endif
 
 #else /* !__ASSEMBLY__ */
@@ -567,6 +605,10 @@
 DECLARE_IDTENTRY_RAW(X86_TRAP_BP,		exc_int3);
 DECLARE_IDTENTRY_RAW_ERRORCODE(X86_TRAP_PF,	exc_page_fault);
 
+#if defined(CONFIG_IA32_EMULATION)
+DECLARE_IDTENTRY_RAW(IA32_SYSCALL_VECTOR,	int80_emulation);
+#endif
+
 #ifdef CONFIG_X86_MCE
 #ifdef CONFIG_X86_64
 DECLARE_IDTENTRY_MCE(X86_TRAP_MC,	exc_machine_check);
@@ -645,23 +687,36 @@
 DECLARE_IDTENTRY_SYSVEC(REBOOT_VECTOR,			sysvec_reboot);
 DECLARE_IDTENTRY_SYSVEC(CALL_FUNCTION_SINGLE_VECTOR,	sysvec_call_function_single);
 DECLARE_IDTENTRY_SYSVEC(CALL_FUNCTION_VECTOR,		sysvec_call_function);
+#else
+# define fred_sysvec_reschedule_ipi			NULL
+# define fred_sysvec_reboot				NULL
+# define fred_sysvec_call_function_single		NULL
+# define fred_sysvec_call_function			NULL
 #endif
 
 #ifdef CONFIG_X86_LOCAL_APIC
 # ifdef CONFIG_X86_MCE_THRESHOLD
 DECLARE_IDTENTRY_SYSVEC(THRESHOLD_APIC_VECTOR,		sysvec_threshold);
+# else
+# define fred_sysvec_threshold				NULL
 # endif
 
 # ifdef CONFIG_X86_MCE_AMD
 DECLARE_IDTENTRY_SYSVEC(DEFERRED_ERROR_VECTOR,		sysvec_deferred_error);
+# else
+# define fred_sysvec_deferred_error			NULL
 # endif
 
 # ifdef CONFIG_X86_THERMAL_VECTOR
 DECLARE_IDTENTRY_SYSVEC(THERMAL_APIC_VECTOR,		sysvec_thermal);
+# else
+# define fred_sysvec_thermal				NULL
 # endif
 
 # ifdef CONFIG_IRQ_WORK
 DECLARE_IDTENTRY_SYSVEC(IRQ_WORK_VECTOR,		sysvec_irq_work);
+# else
+# define fred_sysvec_irq_work				NULL
 # endif
 #endif
 
@@ -669,12 +724,16 @@
 DECLARE_IDTENTRY_SYSVEC(POSTED_INTR_VECTOR,		sysvec_kvm_posted_intr_ipi);
 DECLARE_IDTENTRY_SYSVEC(POSTED_INTR_WAKEUP_VECTOR,	sysvec_kvm_posted_intr_wakeup_ipi);
 DECLARE_IDTENTRY_SYSVEC(POSTED_INTR_NESTED_VECTOR,	sysvec_kvm_posted_intr_nested_ipi);
+#else
+# define fred_sysvec_kvm_posted_intr_ipi		NULL
+# define fred_sysvec_kvm_posted_intr_wakeup_ipi		NULL
+# define fred_sysvec_kvm_posted_intr_nested_ipi		NULL
 #endif
 
 #if IS_ENABLED(CONFIG_HYPERV)
 DECLARE_IDTENTRY_SYSVEC(HYPERVISOR_CALLBACK_VECTOR,	sysvec_hyperv_callback);
 DECLARE_IDTENTRY_SYSVEC(HYPERV_REENLIGHTENMENT_VECTOR,	sysvec_hyperv_reenlightenment);
-DECLARE_IDTENTRY_SYSVEC(HYPERV_STIMER0_VECTOR,	sysvec_hyperv_stimer0);
+DECLARE_IDTENTRY_SYSVEC(HYPERV_STIMER0_VECTOR,		sysvec_hyperv_stimer0);
 #endif
 
 #if IS_ENABLED(CONFIG_ACRN_GUEST)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/insn-eval.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/insn-eval.h
@@ -15,12 +15,15 @@
 #define INSN_CODE_SEG_OPND_SZ(params) (params & 0xf)
 #define INSN_CODE_SEG_PARAMS(oper_sz, addr_sz) (oper_sz | (addr_sz << 4))
 
+int pt_regs_offset(struct pt_regs *regs, int regno);
+
 bool insn_has_rep_prefix(struct insn *insn);
 void __user *insn_get_addr_ref(struct insn *insn, struct pt_regs *regs);
 int insn_get_modrm_rm_off(struct insn *insn, struct pt_regs *regs);
 int insn_get_modrm_reg_off(struct insn *insn, struct pt_regs *regs);
 unsigned long insn_get_seg_base(struct pt_regs *regs, int seg_reg_idx);
 int insn_get_code_seg_params(struct pt_regs *regs);
+int insn_get_effective_ip(struct pt_regs *regs, unsigned long *ip);
 int insn_fetch_from_user(struct pt_regs *regs,
 			 unsigned char buf[MAX_INSN_SIZE]);
 int insn_fetch_from_user_inatomic(struct pt_regs *regs,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/intel-family.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/intel-family.h
@@ -26,6 +26,8 @@
  *		_G	- parts with extra graphics on
  *		_X	- regular server parts
  *		_D	- micro server parts
+ *		_N,_P	- other mobile parts
+ *		_S	- other client parts
  *
  *		Historical OPTDIFFs:
  *
@@ -105,10 +107,24 @@
 
 #define INTEL_FAM6_SAPPHIRERAPIDS_X	0x8F	/* Golden Cove */
 
+#define INTEL_FAM6_EMERALDRAPIDS_X	0xCF
+
+#define INTEL_FAM6_GRANITERAPIDS_X	0xAD
+#define INTEL_FAM6_GRANITERAPIDS_D	0xAE
+
 #define INTEL_FAM6_ALDERLAKE		0x97	/* Golden Cove / Gracemont */
 #define INTEL_FAM6_ALDERLAKE_L		0x9A	/* Golden Cove / Gracemont */
+#define INTEL_FAM6_ALDERLAKE_N		0xBE
+
+#define INTEL_FAM6_RAPTORLAKE		0xB7
+#define INTEL_FAM6_RAPTORLAKE_P		0xBA
+#define INTEL_FAM6_RAPTORLAKE_S		0xBF
+
+#define INTEL_FAM6_LUNARLAKE_M		0xBD
 
-/* "Small Core" Processors (Atom) */
+#define INTEL_FAM6_ARROWLAKE		0xC6
+
+/* "Small Core" Processors (Atom/E-Core) */
 
 #define INTEL_FAM6_ATOM_BONNELL		0x1C /* Diamondville, Pineview */
 #define INTEL_FAM6_ATOM_BONNELL_MID	0x26 /* Silverthorne, Lincroft */
@@ -135,6 +151,10 @@
 #define INTEL_FAM6_ATOM_TREMONT		0x96 /* Elkhart Lake */
 #define INTEL_FAM6_ATOM_TREMONT_L	0x9C /* Jasper Lake */
 
+#define INTEL_FAM6_SIERRAFOREST_X	0xAF
+
+#define INTEL_FAM6_GRANDRIDGE		0xB6
+
 /* Xeon Phi */
 
 #define INTEL_FAM6_XEON_PHI_KNL		0x57 /* Knights Landing */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/iommu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/iommu.h
@@ -17,8 +17,10 @@
 {
 	u64 start = rmrr->base_address;
 	u64 end = rmrr->end_address + 1;
+	int entry_type;
 
-	if (e820__mapped_all(start, end, E820_TYPE_RESERVED))
+	entry_type = e820__get_entry_type(start, end);
+	if (entry_type == E820_TYPE_RESERVED || entry_type == E820_TYPE_NVS)
 		return 0;
 
 	pr_err(FW_BUG "No firmware reserved region can cover this RMRR [%#018Lx-%#018Lx], contact BIOS vendor for fixes\n",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/irq_stack.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/irq_stack.h
@@ -58,7 +58,7 @@
  *     the output constraints to make the compiler aware that R11 cannot be
  *     reused after the asm() statement.
  *
- *     For builds with CONFIG_UNWIND_FRAME_POINTER ASM_CALL_CONSTRAINT is
+ *     For builds with CONFIG_UNWINDER_FRAME_POINTER, ASM_CALL_CONSTRAINT is
  *     required as well as this prevents certain creative GCC variants from
  *     misplacing the ASM code.
  *
@@ -77,11 +77,11 @@
  *     Function calls can clobber anything except the callee-saved
  *     registers. Tell the compiler.
  */
-#define call_on_irqstack(func, asm_call, argconstr...)			\
+#define call_on_stack(stack, func, asm_call, argconstr...)		\
 {									\
 	register void *tos asm("r11");					\
 									\
-	tos = ((void *)__this_cpu_read(hardirq_stack_ptr));		\
+	tos = ((void *)(stack));					\
 									\
 	asm_inline volatile(						\
 	"movq	%%rsp, (%[tos])				\n"		\
@@ -98,6 +98,26 @@
 	);								\
 }
 
+#define ASM_CALL_ARG0							\
+	"call %P[__func]				\n"		\
+	ASM_REACHABLE
+
+#define ASM_CALL_ARG1							\
+	"movq	%[arg1], %%rdi				\n"		\
+	ASM_CALL_ARG0
+
+#define ASM_CALL_ARG2							\
+	"movq	%[arg2], %%rsi				\n"		\
+	ASM_CALL_ARG1
+
+#define ASM_CALL_ARG3							\
+	"movq	%[arg3], %%rdx				\n"		\
+	ASM_CALL_ARG2
+
+#define call_on_irqstack(func, asm_call, argconstr...)			\
+	call_on_stack(__this_cpu_read(hardirq_stack_ptr),		\
+		      func, asm_call, argconstr)
+
 /* Macros to assert type correctness for run_*_on_irqstack macros */
 #define assert_function_type(func, proto)				\
 	static_assert(__builtin_types_compatible_p(typeof(&func), proto))
@@ -147,8 +167,7 @@
  */
 #define ASM_CALL_SYSVEC							\
 	"call irq_enter_rcu				\n"		\
-	"movq	%[arg1], %%rdi				\n"		\
-	"call %P[__func]				\n"		\
+	ASM_CALL_ARG1							\
 	"call irq_exit_rcu				\n"
 
 #define SYSVEC_CONSTRAINTS	, [arg1] "r" (regs)
@@ -168,12 +187,10 @@
  */
 #define ASM_CALL_IRQ							\
 	"call irq_enter_rcu				\n"		\
-	"movq	%[arg1], %%rdi				\n"		\
-	"movl	%[arg2], %%esi				\n"		\
-	"call %P[__func]				\n"		\
+	ASM_CALL_ARG2							\
 	"call irq_exit_rcu				\n"
 
-#define IRQ_CONSTRAINTS	, [arg1] "r" (regs), [arg2] "r" (vector)
+#define IRQ_CONSTRAINTS	, [arg1] "r" (regs), [arg2] "r" ((unsigned long)vector)
 
 #define run_irq_on_irqstack_cond(func, regs, vector)			\
 {									\
@@ -185,9 +202,6 @@
 			      IRQ_CONSTRAINTS, regs, vector);		\
 }
 
-#define ASM_CALL_SOFTIRQ						\
-	"call %P[__func]				\n"
-
 /*
  * Macro to invoke __do_softirq on the irq stack. This is only called from
  * task context when bottom halves are about to be reenabled and soft
@@ -197,7 +211,7 @@
 #define do_softirq_own_stack()						\
 {									\
 	__this_cpu_write(hardirq_stack_inuse, true);			\
-	call_on_irqstack(__do_softirq, ASM_CALL_SOFTIRQ);		\
+	call_on_irqstack(__do_softirq, ASM_CALL_ARG0);			\
 	__this_cpu_write(hardirq_stack_inuse, false);			\
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/irq_work.h
@@ -9,7 +9,6 @@
 {
 	return boot_cpu_has(X86_FEATURE_APIC);
 }
-extern void arch_irq_work_raise(void);
 #else
 static inline bool arch_irq_work_has_interrupt(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/kasan.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/kasan.h
@@ -28,9 +28,12 @@
 #ifdef CONFIG_KASAN
 void __init kasan_early_init(void);
 void __init kasan_init(void);
+void __init kasan_populate_shadow_for_vaddr(void *va, size_t size, int nid);
 #else
 static inline void kasan_early_init(void) { }
 static inline void kasan_init(void) { }
+static inline void kasan_populate_shadow_for_vaddr(void *va, size_t size,
+						   int nid) { }
 #endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/kexec.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/kexec.h
@@ -186,6 +186,14 @@
 extern void arch_kexec_pre_free_pages(void *vaddr, unsigned int pages);
 #define arch_kexec_pre_free_pages arch_kexec_pre_free_pages
 
+#ifdef CONFIG_KEXEC_FILE
+struct purgatory_info;
+int arch_kexec_apply_relocations_add(struct purgatory_info *pi,
+				     Elf_Shdr *section,
+				     const Elf_Shdr *relsec,
+				     const Elf_Shdr *symtab);
+#define arch_kexec_apply_relocations_add arch_kexec_apply_relocations_add
+#endif
 #endif
 
 typedef void crash_vmclear_fn(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/kprobes.h
@@ -49,7 +49,6 @@
 extern const int kretprobe_blacklist_size;
 
 void arch_remove_kprobe(struct kprobe *p);
-asmlinkage void kretprobe_trampoline(void);
 
 extern void arch_kprobe_override_function(struct pt_regs *regs);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/kvm-x86-ops.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/kvm-x86-ops.h
@@ -34,6 +34,7 @@
 KVM_X86_OP(get_cpl)
 KVM_X86_OP(set_segment)
 KVM_X86_OP_NULL(get_cs_db_l_bits)
+KVM_X86_OP(is_valid_cr0)
 KVM_X86_OP(set_cr0)
 KVM_X86_OP(is_valid_cr4)
 KVM_X86_OP(set_cr4)
@@ -47,6 +48,7 @@
 KVM_X86_OP(cache_reg)
 KVM_X86_OP(get_rflags)
 KVM_X86_OP(set_rflags)
+KVM_X86_OP(get_if_flag)
 KVM_X86_OP(tlb_flush_all)
 KVM_X86_OP(tlb_flush_current)
 KVM_X86_OP_NULL(tlb_remote_flush)
@@ -114,6 +116,7 @@
 KVM_X86_OP_NULL(mem_enc_op)
 KVM_X86_OP_NULL(mem_enc_reg_region)
 KVM_X86_OP_NULL(mem_enc_unreg_region)
+KVM_X86_OP_NULL(guest_memory_reclaimed)
 KVM_X86_OP(get_msr_feature)
 KVM_X86_OP(can_emulate_instruction)
 KVM_X86_OP(apic_init_signal_blocked)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/kvm_host.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/kvm_host.h
@@ -98,7 +98,7 @@
 	KVM_ARCH_REQ_FLAGS(25, KVM_REQUEST_WAIT | KVM_REQUEST_NO_WAKEUP)
 #define KVM_REQ_TLB_FLUSH_CURRENT	KVM_ARCH_REQ(26)
 #define KVM_REQ_TLB_FLUSH_GUEST \
-	KVM_ARCH_REQ_FLAGS(27, KVM_REQUEST_NO_WAKEUP)
+	KVM_ARCH_REQ_FLAGS(27, KVM_REQUEST_WAIT | KVM_REQUEST_NO_WAKEUP)
 #define KVM_REQ_APF_READY		KVM_ARCH_REQ(28)
 #define KVM_REQ_MSR_FILTER_CHANGED	KVM_ARCH_REQ(29)
 #define KVM_REQ_UPDATE_CPU_DIRTY_LOGGING \
@@ -364,6 +364,7 @@
 		unsigned int cr4_smap:1;
 		unsigned int cr4_smep:1;
 		unsigned int cr4_la57:1;
+		unsigned int efer_lma:1;
 	};
 };
 
@@ -497,6 +498,7 @@
 	unsigned nr_arch_fixed_counters;
 	unsigned available_event_types;
 	u64 fixed_ctr_ctrl;
+	u64 fixed_ctr_ctrl_mask;
 	u64 global_ctrl;
 	u64 global_status;
 	u64 global_ovf_ctrl;
@@ -504,6 +506,7 @@
 	u64 global_ctrl_mask;
 	u64 global_ovf_ctrl_mask;
 	u64 reserved_bits;
+	u64 raw_event_mask;
 	u8 version;
 	struct kvm_pmc gp_counters[INTEL_PMC_MAX_GENERIC];
 	struct kvm_pmc fixed_counters[INTEL_PMC_MAX_FIXED];
@@ -640,6 +643,7 @@
 	u64 ia32_misc_enable_msr;
 	u64 smbase;
 	u64 smi_count;
+	bool at_instruction_boundary;
 	bool tpr_access_reporting;
 	bool xsaves_enabled;
 	u64 ia32_xss;
@@ -691,11 +695,10 @@
 	 *
 	 * Note that while the PKRU state lives inside the fpu registers,
 	 * it is switched out separately at VMENTER and VMEXIT time. The
-	 * "guest_fpu" state here contains the guest FPU context, with the
+	 * "guest_fpstate" state here contains the guest FPU context, with the
 	 * host PRKU bits.
 	 */
-	struct fpu *user_fpu;
-	struct fpu *guest_fpu;
+	struct fpu_guest guest_fpu;
 
 	u64 xcr0;
 	u64 guest_supported_xcr0;
@@ -728,6 +731,7 @@
 
 	int cpuid_nent;
 	struct kvm_cpuid_entry2 *cpuid_entries;
+	bool is_amd_compatible;
 
 	u64 reserved_gpa_bits;
 	int maxphyaddr;
@@ -751,7 +755,7 @@
 		u8 preempted;
 		u64 msr_val;
 		u64 last_steal;
-		struct gfn_to_pfn_cache cache;
+		struct gfn_to_hva_cache cache;
 	} st;
 
 	u64 l1_tsc_offset;
@@ -1165,6 +1169,9 @@
 	 */
 	bool tdp_mmu_enabled;
 
+	/* The number of TDP MMU pages across all roots. */
+	atomic64_t tdp_mmu_pages;
+
 	/*
 	 * List of struct kvm_mmu_pages being used as roots.
 	 * All struct kvm_mmu_pages in the list should have
@@ -1186,17 +1193,9 @@
 	struct list_head tdp_mmu_roots;
 
 	/*
-	 * List of struct kvmp_mmu_pages not being used as roots.
-	 * All struct kvm_mmu_pages in the list should have
-	 * tdp_mmu_page set and a tdp_mmu_root_count of 0.
-	 */
-	struct list_head tdp_mmu_pages;
-
-	/*
 	 * Protects accesses to the following fields when the MMU lock
 	 * is held in read mode:
 	 *  - tdp_mmu_roots (above)
-	 *  - tdp_mmu_pages (above)
 	 *  - the link field of struct kvm_mmu_pages used by the TDP MMU
 	 *  - lpage_disallowed_mmu_pages
 	 *  - the lpage_disallowed_link field of struct kvm_mmu_pages used
@@ -1269,6 +1268,8 @@
 	u64 nested_run;
 	u64 directed_yield_attempted;
 	u64 directed_yield_successful;
+	u64 preemption_reported;
+	u64 preemption_other;
 	u64 guest_mode;
 };
 
@@ -1327,8 +1328,9 @@
 	void (*set_segment)(struct kvm_vcpu *vcpu,
 			    struct kvm_segment *var, int seg);
 	void (*get_cs_db_l_bits)(struct kvm_vcpu *vcpu, int *db, int *l);
+	bool (*is_valid_cr0)(struct kvm_vcpu *vcpu, unsigned long cr0);
 	void (*set_cr0)(struct kvm_vcpu *vcpu, unsigned long cr0);
-	bool (*is_valid_cr4)(struct kvm_vcpu *vcpu, unsigned long cr0);
+	bool (*is_valid_cr4)(struct kvm_vcpu *vcpu, unsigned long cr4);
 	void (*set_cr4)(struct kvm_vcpu *vcpu, unsigned long cr4);
 	int (*set_efer)(struct kvm_vcpu *vcpu, u64 efer);
 	void (*get_idt)(struct kvm_vcpu *vcpu, struct desc_ptr *dt);
@@ -1340,6 +1342,7 @@
 	void (*cache_reg)(struct kvm_vcpu *vcpu, enum kvm_reg reg);
 	unsigned long (*get_rflags)(struct kvm_vcpu *vcpu);
 	void (*set_rflags)(struct kvm_vcpu *vcpu, unsigned long rflags);
+	bool (*get_if_flag)(struct kvm_vcpu *vcpu);
 
 	void (*tlb_flush_all)(struct kvm_vcpu *vcpu);
 	void (*tlb_flush_current)(struct kvm_vcpu *vcpu);
@@ -1469,6 +1472,7 @@
 	int (*mem_enc_reg_region)(struct kvm *kvm, struct kvm_enc_region *argp);
 	int (*mem_enc_unreg_region)(struct kvm *kvm, struct kvm_enc_region *argp);
 	int (*vm_copy_enc_context_from)(struct kvm *kvm, unsigned int source_fd);
+	void (*guest_memory_reclaimed)(struct kvm *kvm);
 
 	int (*get_msr_feature)(struct kvm_msr_entry *entry);
 
@@ -1485,6 +1489,7 @@
 };
 
 struct kvm_x86_nested_ops {
+	void (*leave_nested)(struct kvm_vcpu *vcpu);
 	int (*check_events)(struct kvm_vcpu *vcpu);
 	bool (*hv_timer_pending)(struct kvm_vcpu *vcpu);
 	void (*triple_fault)(struct kvm_vcpu *vcpu);
@@ -1507,6 +1512,7 @@
 	int (*disabled_by_bios)(void);
 	int (*check_processor_compatibility)(void);
 	int (*hardware_setup)(void);
+	bool (*intel_pt_intr_in_guest)(void);
 
 	struct kvm_x86_ops *runtime_ops;
 };
@@ -1542,6 +1548,8 @@
 {
 	return __vmalloc(kvm_x86_ops.vm_size, GFP_KERNEL_ACCOUNT | __GFP_ZERO);
 }
+
+#define __KVM_HAVE_ARCH_VM_FREE
 void kvm_arch_free_vm(struct kvm *kvm);
 
 #define __KVM_HAVE_ARCH_FLUSH_REMOTE_TLB
@@ -1554,8 +1562,9 @@
 		return -ENOTSUPP;
 }
 
-int kvm_mmu_module_init(void);
-void kvm_mmu_module_exit(void);
+void __init kvm_mmu_x86_module_init(void);
+int kvm_mmu_vendor_module_init(void);
+void kvm_mmu_vendor_module_exit(void);
 
 void kvm_mmu_destroy(struct kvm_vcpu *vcpu);
 int kvm_mmu_create(struct kvm_vcpu *vcpu);
@@ -1686,8 +1695,6 @@
 int kvm_task_switch(struct kvm_vcpu *vcpu, u16 tss_selector, int idt_index,
 		    int reason, bool has_error_code, u32 error_code);
 
-void kvm_free_guest_fpu(struct kvm_vcpu *vcpu);
-
 void kvm_post_set_cr0(struct kvm_vcpu *vcpu, unsigned long old_cr0, unsigned long cr0);
 void kvm_post_set_cr4(struct kvm_vcpu *vcpu, unsigned long old_cr4, unsigned long cr4);
 int kvm_set_cr0(struct kvm_vcpu *vcpu, unsigned long cr0);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/linkage.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/linkage.h
@@ -11,12 +11,36 @@
 #define asmlinkage CPP_ASMLINKAGE __attribute__((regparm(0)))
 #endif /* CONFIG_X86_32 */
 
+#define __ALIGN		.balign CONFIG_FUNCTION_ALIGNMENT, 0x90;
+#define __ALIGN_STR	__stringify(__ALIGN)
+
+#define ASM_FUNC_ALIGN		__ALIGN_STR
+#define __FUNC_ALIGN		__ALIGN
+#define SYM_F_ALIGN		__FUNC_ALIGN
+
 #ifdef __ASSEMBLY__
 
-#if defined(CONFIG_X86_64) || defined(CONFIG_X86_ALIGNMENT_16)
-#define __ALIGN		.p2align 4, 0x90
-#define __ALIGN_STR	__stringify(__ALIGN)
+#if defined(CONFIG_RETHUNK) && !defined(__DISABLE_EXPORTS) && !defined(BUILD_VDSO)
+#define RET	jmp __x86_return_thunk
+#else /* CONFIG_RETPOLINE */
+#ifdef CONFIG_SLS
+#define RET	ret; int3
+#else
+#define RET	ret
+#endif
+#endif /* CONFIG_RETPOLINE */
+
+#else /* __ASSEMBLY__ */
+
+#if defined(CONFIG_RETHUNK) && !defined(__DISABLE_EXPORTS) && !defined(BUILD_VDSO)
+#define ASM_RET	"jmp __x86_return_thunk\n\t"
+#else /* CONFIG_RETPOLINE */
+#ifdef CONFIG_SLS
+#define ASM_RET	"ret; int3\n\t"
+#else
+#define ASM_RET	"ret\n\t"
 #endif
+#endif /* CONFIG_RETPOLINE */
 
 #endif /* __ASSEMBLY__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/mem_encrypt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/mem_encrypt.h
@@ -13,6 +13,7 @@
 #ifndef __ASSEMBLY__
 
 #include <linux/init.h>
+#include <linux/cc_platform.h>
 
 #include <asm/bootparam.h>
 
@@ -46,14 +47,13 @@
 
 void __init mem_encrypt_free_decrypted_mem(void);
 
-/* Architecture __weak replacement functions */
-void __init mem_encrypt_init(void);
-
 void __init sev_es_init_vc_handling(void);
 bool sme_active(void);
 bool sev_active(void);
 bool sev_es_active(void);
 
+void __init mem_encrypt_init(void);
+
 #define __bss_decrypted __section(".bss..decrypted")
 
 #else	/* !CONFIG_AMD_MEM_ENCRYPT */
@@ -86,6 +86,8 @@
 
 static inline void mem_encrypt_free_decrypted_mem(void) { }
 
+static inline void mem_encrypt_init(void) { }
+
 #define __bss_decrypted
 
 #endif	/* CONFIG_AMD_MEM_ENCRYPT */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/microcode.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/microcode.h
@@ -5,10 +5,12 @@
 #include <asm/cpu.h>
 #include <linux/earlycpio.h>
 #include <linux/initrd.h>
+#include <asm/microcode_amd.h>
 
 struct ucode_patch {
 	struct list_head plist;
 	void *data;		/* Intel uses only this one */
+	unsigned int size;
 	u32 patch_id;
 	u16 equiv_cpu;
 };
@@ -129,13 +131,15 @@
 #ifdef CONFIG_MICROCODE
 extern void __init load_ucode_bsp(void);
 extern void load_ucode_ap(void);
-void reload_early_microcode(void);
+void reload_early_microcode(unsigned int cpu);
 extern bool get_builtin_firmware(struct cpio_data *cd, const char *name);
 extern bool initrd_gone;
+void microcode_bsp_resume(void);
 #else
 static inline void __init load_ucode_bsp(void)			{ }
 static inline void load_ucode_ap(void)				{ }
-static inline void reload_early_microcode(void)			{ }
+static inline void reload_early_microcode(unsigned int cpu)	{ }
+static inline void microcode_bsp_resume(void)			{ }
 static inline bool
 get_builtin_firmware(struct cpio_data *cd, const char *name)	{ return false; }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/microcode_amd.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/microcode_amd.h
@@ -47,12 +47,14 @@
 extern void __init load_ucode_amd_bsp(unsigned int family);
 extern void load_ucode_amd_ap(unsigned int family);
 extern int __init save_microcode_in_initrd_amd(unsigned int family);
-void reload_ucode_amd(void);
+void reload_ucode_amd(unsigned int cpu);
+extern void amd_check_microcode(void);
 #else
 static inline void __init load_ucode_amd_bsp(unsigned int family) {}
 static inline void load_ucode_amd_ap(unsigned int family) {}
 static inline int __init
 save_microcode_in_initrd_amd(unsigned int family) { return -EINVAL; }
-static inline void reload_ucode_amd(void) {}
+static inline void reload_ucode_amd(unsigned int cpu) {}
+static inline void amd_check_microcode(void) {}
 #endif
 #endif /* _ASM_X86_MICROCODE_AMD_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/mmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/mmu.h
@@ -33,6 +33,8 @@
 	 */
 	atomic64_t tlb_gen;
 
+	unsigned long next_trim_cpumask;
+
 #ifdef CONFIG_MODIFY_LDT_SYSCALL
 	struct rw_semaphore	ldt_usr_sem;
 	struct ldt_struct	*ldt;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/mmu_context.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/mmu_context.h
@@ -106,6 +106,7 @@
 
 	mm->context.ctx_id = atomic64_inc_return(&last_mm_ctx_id);
 	atomic64_set(&mm->context.tlb_gen, 0);
+	mm->context.next_trim_cpumask = jiffies + HZ;
 
 #ifdef CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS
 	if (cpu_feature_enabled(X86_FEATURE_OSPKE)) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/mshyperv.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/mshyperv.h
@@ -176,13 +176,6 @@
 static inline void hv_apic_init(void) {}
 #endif
 
-static inline void hv_set_msi_entry_from_desc(union hv_msi_entry *msi_entry,
-					      struct msi_desc *msi_desc)
-{
-	msi_entry->address.as_uint32 = msi_desc->msg.address_lo;
-	msi_entry->data.as_uint32 = msi_desc->msg.data;
-}
-
 struct irq_domain *hv_create_pci_msi_domain(void);
 
 int hv_map_ioapic_interrupt(int ioapic_id, bool level, int vcpu, int vector,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/msi.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/msi.h
@@ -12,14 +12,17 @@
 /* Structs and defines for the X86 specific MSI message format */
 
 typedef struct x86_msi_data {
-	u32	vector			:  8,
-		delivery_mode		:  3,
-		dest_mode_logical	:  1,
-		reserved		:  2,
-		active_low		:  1,
-		is_level		:  1;
-
-	u32	dmar_subhandle;
+	union {
+		struct {
+			u32	vector			:  8,
+				delivery_mode		:  3,
+				dest_mode_logical	:  1,
+				reserved		:  2,
+				active_low		:  1,
+				is_level		:  1;
+		};
+		u32	dmar_subhandle;
+	};
 } __attribute__ ((packed)) arch_msi_msg_data_t;
 #define arch_msi_msg_data	x86_msi_data
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/msr-index.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/msr-index.h
@@ -30,6 +30,7 @@
 #define _EFER_SVME		12 /* Enable virtualization */
 #define _EFER_LMSLE		13 /* Long Mode Segment Limit Enable */
 #define _EFER_FFXSR		14 /* Enable Fast FXSAVE/FXRSTOR */
+#define _EFER_AUTOIBRS		21 /* Enable Automatic IBRS */
 
 #define EFER_SCE		(1<<_EFER_SCE)
 #define EFER_LME		(1<<_EFER_LME)
@@ -38,6 +39,7 @@
 #define EFER_SVME		(1<<_EFER_SVME)
 #define EFER_LMSLE		(1<<_EFER_LMSLE)
 #define EFER_FFXSR		(1<<_EFER_FFXSR)
+#define EFER_AUTOIBRS		(1<<_EFER_AUTOIBRS)
 
 /* Intel MSRs. Some also available on other CPUs */
 
@@ -51,9 +53,19 @@
 #define SPEC_CTRL_STIBP			BIT(SPEC_CTRL_STIBP_SHIFT)	/* STIBP mask */
 #define SPEC_CTRL_SSBD_SHIFT		2	   /* Speculative Store Bypass Disable bit */
 #define SPEC_CTRL_SSBD			BIT(SPEC_CTRL_SSBD_SHIFT)	/* Speculative Store Bypass Disable */
+#define SPEC_CTRL_RRSBA_DIS_S_SHIFT	6	   /* Disable RRSBA behavior */
+#define SPEC_CTRL_RRSBA_DIS_S		BIT(SPEC_CTRL_RRSBA_DIS_S_SHIFT)
+#define SPEC_CTRL_BHI_DIS_S_SHIFT	10	   /* Disable Branch History Injection behavior */
+#define SPEC_CTRL_BHI_DIS_S		BIT(SPEC_CTRL_BHI_DIS_S_SHIFT)
+
+/* A mask for bits which the kernel toggles when controlling mitigations */
+#define SPEC_CTRL_MITIGATIONS_MASK	(SPEC_CTRL_IBRS | SPEC_CTRL_STIBP | SPEC_CTRL_SSBD \
+							| SPEC_CTRL_RRSBA_DIS_S \
+							| SPEC_CTRL_BHI_DIS_S)
 
 #define MSR_IA32_PRED_CMD		0x00000049 /* Prediction Command */
 #define PRED_CMD_IBPB			BIT(0)	   /* Indirect Branch Prediction Barrier */
+#define PRED_CMD_SBPB			BIT(7)	   /* Selective Branch Prediction Barrier */
 
 #define MSR_PPIN_CTL			0x0000004e
 #define MSR_PPIN			0x0000004f
@@ -91,6 +103,7 @@
 #define MSR_IA32_ARCH_CAPABILITIES	0x0000010a
 #define ARCH_CAP_RDCL_NO		BIT(0)	/* Not susceptible to Meltdown */
 #define ARCH_CAP_IBRS_ALL		BIT(1)	/* Enhanced IBRS support */
+#define ARCH_CAP_RSBA			BIT(2)	/* RET may use alternative branch predictors */
 #define ARCH_CAP_SKIP_VMENTRY_L1DFLUSH	BIT(3)	/* Skip L1D flush on vmentry */
 #define ARCH_CAP_SSB_NO			BIT(4)	/*
 						 * Not susceptible to Speculative Store Bypass
@@ -114,6 +127,62 @@
 						 * Not susceptible to
 						 * TSX Async Abort (TAA) vulnerabilities.
 						 */
+#define ARCH_CAP_SBDR_SSDP_NO		BIT(13)	/*
+						 * Not susceptible to SBDR and SSDP
+						 * variants of Processor MMIO stale data
+						 * vulnerabilities.
+						 */
+#define ARCH_CAP_FBSDP_NO		BIT(14)	/*
+						 * Not susceptible to FBSDP variant of
+						 * Processor MMIO stale data
+						 * vulnerabilities.
+						 */
+#define ARCH_CAP_PSDP_NO		BIT(15)	/*
+						 * Not susceptible to PSDP variant of
+						 * Processor MMIO stale data
+						 * vulnerabilities.
+						 */
+#define ARCH_CAP_FB_CLEAR		BIT(17)	/*
+						 * VERW clears CPU fill buffer
+						 * even on MDS_NO CPUs.
+						 */
+#define ARCH_CAP_FB_CLEAR_CTRL		BIT(18)	/*
+						 * MSR_IA32_MCU_OPT_CTRL[FB_CLEAR_DIS]
+						 * bit available to control VERW
+						 * behavior.
+						 */
+#define ARCH_CAP_RRSBA			BIT(19)	/*
+						 * Indicates RET may use predictors
+						 * other than the RSB. With eIBRS
+						 * enabled predictions in kernel mode
+						 * are restricted to targets in
+						 * kernel.
+						 */
+#define ARCH_CAP_BHI_NO			BIT(20)	/*
+						 * CPU is not affected by Branch
+						 * History Injection.
+						 */
+#define ARCH_CAP_PBRSB_NO		BIT(24)	/*
+						 * Not susceptible to Post-Barrier
+						 * Return Stack Buffer Predictions.
+						 */
+#define ARCH_CAP_GDS_CTRL		BIT(25)	/*
+						 * CPU is vulnerable to Gather
+						 * Data Sampling (GDS) and
+						 * has controls for mitigation.
+						 */
+#define ARCH_CAP_GDS_NO			BIT(26)	/*
+						 * CPU is not vulnerable to Gather
+						 * Data Sampling (GDS).
+						 */
+#define ARCH_CAP_RFDS_NO		BIT(27)	/*
+						 * Not susceptible to Register
+						 * File Data Sampling.
+						 */
+#define ARCH_CAP_RFDS_CLEAR		BIT(28)	/*
+						 * VERW clears CPU Register
+						 * File.
+						 */
 
 #define MSR_IA32_FLUSH_CMD		0x0000010b
 #define L1D_FLUSH			BIT(0)	/*
@@ -128,9 +197,12 @@
 #define TSX_CTRL_RTM_DISABLE		BIT(0)	/* Disable RTM feature */
 #define TSX_CTRL_CPUID_CLEAR		BIT(1)	/* Disable TSX enumeration */
 
-/* SRBDS support */
 #define MSR_IA32_MCU_OPT_CTRL		0x00000123
-#define RNGDS_MITG_DIS			BIT(0)
+#define RNGDS_MITG_DIS			BIT(0)	/* SRBDS support */
+#define RTM_ALLOW			BIT(1)	/* TSX development mode */
+#define FB_CLEAR_DIS			BIT(3)	/* CPU Fill buffer clear disable */
+#define GDS_MITG_DIS			BIT(4)	/* Disable GDS mitigation */
+#define GDS_MITG_LOCKED			BIT(5)	/* GDS mitigation locked */
 
 #define MSR_IA32_SYSENTER_CS		0x00000174
 #define MSR_IA32_SYSENTER_ESP		0x00000175
@@ -265,7 +337,8 @@
 #define MSR_IA32_PASID_VALID		BIT_ULL(31)
 
 /* DEBUGCTLMSR bits (others vary by model): */
-#define DEBUGCTLMSR_LBR			(1UL <<  0) /* last branch recording */
+#define DEBUGCTLMSR_LBR_BIT		0	     /* last branch recording */
+#define DEBUGCTLMSR_LBR			(1UL <<  DEBUGCTLMSR_LBR_BIT)
 #define DEBUGCTLMSR_BTF_SHIFT		1
 #define DEBUGCTLMSR_BTF			(1UL <<  1) /* single-step on branches */
 #define DEBUGCTLMSR_BUS_LOCK_DETECT	(1UL <<  2)
@@ -456,6 +529,13 @@
 #define MSR_AMD64_CPUID_FN_1		0xc0011004
 #define MSR_AMD64_LS_CFG		0xc0011020
 #define MSR_AMD64_DC_CFG		0xc0011022
+#define MSR_AMD64_TW_CFG		0xc0011023
+
+#define MSR_AMD64_DE_CFG		0xc0011029
+#define MSR_AMD64_DE_CFG_LFENCE_SERIALIZE_BIT	 1
+#define MSR_AMD64_DE_CFG_LFENCE_SERIALIZE	BIT_ULL(MSR_AMD64_DE_CFG_LFENCE_SERIALIZE_BIT)
+#define MSR_AMD64_DE_CFG_ZEN2_FP_BACKUP_FIX_BIT 9
+
 #define MSR_AMD64_BU_CFG2		0xc001102a
 #define MSR_AMD64_IBSFETCHCTL		0xc0011030
 #define MSR_AMD64_IBSFETCHLINAD		0xc0011031
@@ -486,6 +566,31 @@
 
 #define MSR_AMD64_VIRT_SPEC_CTRL	0xc001011f
 
+/* AMD Collaborative Processor Performance Control MSRs */
+#define MSR_AMD_CPPC_CAP1		0xc00102b0
+#define MSR_AMD_CPPC_ENABLE		0xc00102b1
+#define MSR_AMD_CPPC_CAP2		0xc00102b2
+#define MSR_AMD_CPPC_REQ		0xc00102b3
+#define MSR_AMD_CPPC_STATUS		0xc00102b4
+
+#define AMD_CPPC_LOWEST_PERF(x)		(((x) >> 0) & 0xff)
+#define AMD_CPPC_LOWNONLIN_PERF(x)	(((x) >> 8) & 0xff)
+#define AMD_CPPC_NOMINAL_PERF(x)	(((x) >> 16) & 0xff)
+#define AMD_CPPC_HIGHEST_PERF(x)	(((x) >> 24) & 0xff)
+
+#define AMD_CPPC_MAX_PERF(x)		(((x) & 0xff) << 0)
+#define AMD_CPPC_MIN_PERF(x)		(((x) & 0xff) << 8)
+#define AMD_CPPC_DES_PERF(x)		(((x) & 0xff) << 16)
+#define AMD_CPPC_ENERGY_PERF_PREF(x)	(((x) & 0xff) << 24)
+
+/* Zen4 */
+#define MSR_ZEN4_BP_CFG			0xc001102e
+#define MSR_ZEN4_BP_CFG_SHARED_BTB_FIX_BIT 5
+
+/* Zen 2 */
+#define MSR_ZEN2_SPECTRAL_CHICKEN	0xc00110e3
+#define MSR_ZEN2_SPECTRAL_CHICKEN_BIT	BIT_ULL(1)
+
 /* Fam 17h MSRs */
 #define MSR_F17H_IRPERF			0xc00000e9
 
@@ -530,9 +635,6 @@
 #define FAM10H_MMIO_CONF_BASE_MASK	0xfffffffULL
 #define FAM10H_MMIO_CONF_BASE_SHIFT	20
 #define MSR_FAM10H_NODE_ID		0xc001100c
-#define MSR_F10H_DECFG			0xc0011029
-#define MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT	1
-#define MSR_F10H_DECFG_LFENCE_SERIALIZE		BIT_ULL(MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT)
 
 /* K8 MSRs */
 #define MSR_K8_TOP_MEM1			0xc001001a
@@ -625,6 +727,8 @@
 
 #define MSR_IA32_BNDCFGS_RSVD		0x00000ffc
 
+#define MSR_IA32_XFD			0x000001c4
+#define MSR_IA32_XFD_ERR		0x000001c5
 #define MSR_IA32_XSS			0x00000da0
 
 #define MSR_IA32_APICBASE		0x0000001b
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/msr.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/msr.h
@@ -92,7 +92,7 @@
 
 	asm volatile("1: rdmsr\n"
 		     "2:\n"
-		     _ASM_EXTABLE_HANDLE(1b, 2b, ex_handler_rdmsr_unsafe)
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_RDMSR)
 		     : EAX_EDX_RET(val, low, high) : "c" (msr));
 
 	return EAX_EDX_VAL(val, low, high);
@@ -102,7 +102,7 @@
 {
 	asm volatile("1: wrmsr\n"
 		     "2:\n"
-		     _ASM_EXTABLE_HANDLE(1b, 2b, ex_handler_wrmsr_unsafe)
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_WRMSR)
 		     : : "c" (msr), "a"(low), "d" (high) : "memory");
 }
 
@@ -137,17 +137,11 @@
 {
 	DECLARE_ARGS(val, low, high);
 
-	asm volatile("2: rdmsr ; xor %[err],%[err]\n"
-		     "1:\n\t"
-		     ".section .fixup,\"ax\"\n\t"
-		     "3: mov %[fault],%[err]\n\t"
-		     "xorl %%eax, %%eax\n\t"
-		     "xorl %%edx, %%edx\n\t"
-		     "jmp 1b\n\t"
-		     ".previous\n\t"
-		     _ASM_EXTABLE(2b, 3b)
+	asm volatile("1: rdmsr ; xor %[err],%[err]\n"
+		     "2:\n\t"
+		     _ASM_EXTABLE_TYPE_REG(1b, 2b, EX_TYPE_RDMSR_SAFE, %[err])
 		     : [err] "=r" (*err), EAX_EDX_RET(val, low, high)
-		     : "c" (msr), [fault] "i" (-EIO));
+		     : "c" (msr));
 	if (tracepoint_enabled(read_msr))
 		do_trace_read_msr(msr, EAX_EDX_VAL(val, low, high), *err);
 	return EAX_EDX_VAL(val, low, high);
@@ -169,15 +163,11 @@
 {
 	int err;
 
-	asm volatile("2: wrmsr ; xor %[err],%[err]\n"
-		     "1:\n\t"
-		     ".section .fixup,\"ax\"\n\t"
-		     "3:  mov %[fault],%[err] ; jmp 1b\n\t"
-		     ".previous\n\t"
-		     _ASM_EXTABLE(2b, 3b)
+	asm volatile("1: wrmsr ; xor %[err],%[err]\n"
+		     "2:\n\t"
+		     _ASM_EXTABLE_TYPE_REG(1b, 2b, EX_TYPE_WRMSR_SAFE, %[err])
 		     : [err] "=a" (err)
-		     : "c" (msr), "0" (low), "d" (high),
-		       [fault] "i" (-EIO)
+		     : "c" (msr), "0" (low), "d" (high)
 		     : "memory");
 	if (tracepoint_enabled(write_msr))
 		do_trace_write_msr(msr, ((u64)high << 32 | low), err);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/nospec-branch.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/nospec-branch.h
@@ -5,11 +5,15 @@
 
 #include <linux/static_key.h>
 #include <linux/objtool.h>
+#include <linux/linkage.h>
 
 #include <asm/alternative.h>
 #include <asm/cpufeatures.h>
 #include <asm/msr-index.h>
 #include <asm/unwind_hints.h>
+#include <asm/percpu.h>
+
+#define RETPOLINE_THUNK_SIZE	32
 
 /*
  * Fill the CPU return stack buffer.
@@ -31,32 +35,57 @@
 #define RSB_CLEAR_LOOPS		32	/* To forcibly overwrite all entries */
 
 /*
+ * Common helper for __FILL_RETURN_BUFFER and __FILL_ONE_RETURN.
+ */
+#define __FILL_RETURN_SLOT			\
+	ANNOTATE_INTRA_FUNCTION_CALL;		\
+	call	772f;				\
+	int3;					\
+772:
+
+/*
+ * Stuff the entire RSB.
+ *
  * Google experimented with loop-unrolling and this turned out to be
  * the optimal version - two calls, each with their own speculation
  * trap should their return address end up getting used, in a loop.
  */
-#define __FILL_RETURN_BUFFER(reg, nr, sp)	\
-	mov	$(nr/2), reg;			\
-771:						\
-	ANNOTATE_INTRA_FUNCTION_CALL;		\
-	call	772f;				\
-773:	/* speculation trap */			\
-	UNWIND_HINT_EMPTY;			\
-	pause;					\
-	lfence;					\
-	jmp	773b;				\
-772:						\
-	ANNOTATE_INTRA_FUNCTION_CALL;		\
-	call	774f;				\
-775:	/* speculation trap */			\
-	UNWIND_HINT_EMPTY;			\
-	pause;					\
-	lfence;					\
-	jmp	775b;				\
-774:						\
-	add	$(BITS_PER_LONG/8) * 2, sp;	\
-	dec	reg;				\
-	jnz	771b;
+#ifdef CONFIG_X86_64
+#define __FILL_RETURN_BUFFER(reg, nr)			\
+	mov	$(nr/2), reg;				\
+771:							\
+	__FILL_RETURN_SLOT				\
+	__FILL_RETURN_SLOT				\
+	add	$(BITS_PER_LONG/8) * 2, %_ASM_SP;	\
+	dec	reg;					\
+	jnz	771b;					\
+	/* barrier for jnz misprediction */		\
+	lfence;
+#else
+/*
+ * i386 doesn't unconditionally have LFENCE, as such it can't
+ * do a loop.
+ */
+#define __FILL_RETURN_BUFFER(reg, nr)			\
+	.rept nr;					\
+	__FILL_RETURN_SLOT;				\
+	.endr;						\
+	add	$(BITS_PER_LONG/8) * nr, %_ASM_SP;
+#endif
+
+/*
+ * Stuff a single RSB slot.
+ *
+ * To mitigate Post-Barrier RSB speculation, one CALL instruction must be
+ * forced to retire before letting a RET instruction execute.
+ *
+ * On PBRSB-vulnerable CPUs, it is not safe for a RET to be executed
+ * before this point.
+ */
+#define __FILL_ONE_RETURN				\
+	__FILL_RETURN_SLOT				\
+	add	$(BITS_PER_LONG/8), %_ASM_SP;		\
+	lfence;
 
 #ifdef __ASSEMBLY__
 
@@ -73,6 +102,23 @@
 .endm
 
 /*
+ * (ab)use RETPOLINE_SAFE on RET to annotate away 'bare' RET instructions
+ * vs RETBleed validation.
+ */
+#define ANNOTATE_UNRET_SAFE ANNOTATE_RETPOLINE_SAFE
+
+/*
+ * Abuse ANNOTATE_RETPOLINE_SAFE on a NOP to indicate UNRET_END, should
+ * eventually turn into it's own annotation.
+ */
+.macro ANNOTATE_UNRET_END
+#if (defined(CONFIG_CPU_UNRET_ENTRY) || defined(CONFIG_CPU_SRSO))
+	ANNOTATE_RETPOLINE_SAFE
+	nop
+#endif
+.endm
+
+/*
  * JMP_NOSPEC and CALL_NOSPEC macros can be used instead of a simple
  * indirect jmp/call which may be susceptible to the Spectre variant 2
  * attack.
@@ -81,7 +127,7 @@
 #ifdef CONFIG_RETPOLINE
 	ALTERNATIVE_2 __stringify(ANNOTATE_RETPOLINE_SAFE; jmp *%\reg), \
 		      __stringify(jmp __x86_indirect_thunk_\reg), X86_FEATURE_RETPOLINE, \
-		      __stringify(lfence; ANNOTATE_RETPOLINE_SAFE; jmp *%\reg), X86_FEATURE_RETPOLINE_AMD
+		      __stringify(lfence; ANNOTATE_RETPOLINE_SAFE; jmp *%\reg), X86_FEATURE_RETPOLINE_LFENCE
 #else
 	jmp	*%\reg
 #endif
@@ -91,7 +137,7 @@
 #ifdef CONFIG_RETPOLINE
 	ALTERNATIVE_2 __stringify(ANNOTATE_RETPOLINE_SAFE; call *%\reg), \
 		      __stringify(call __x86_indirect_thunk_\reg), X86_FEATURE_RETPOLINE, \
-		      __stringify(lfence; ANNOTATE_RETPOLINE_SAFE; call *%\reg), X86_FEATURE_RETPOLINE_AMD
+		      __stringify(lfence; ANNOTATE_RETPOLINE_SAFE; call *%\reg), X86_FEATURE_RETPOLINE_LFENCE
 #else
 	call	*%\reg
 #endif
@@ -101,12 +147,82 @@
   * A simpler FILL_RETURN_BUFFER macro. Don't make people use the CPP
   * monstrosity above, manually.
   */
-.macro FILL_RETURN_BUFFER reg:req nr:req ftr:req
-#ifdef CONFIG_RETPOLINE
-	ALTERNATIVE "jmp .Lskip_rsb_\@", "", \ftr
-	__FILL_RETURN_BUFFER(\reg,\nr,%_ASM_SP)
+.macro FILL_RETURN_BUFFER reg:req nr:req ftr:req ftr2=ALT_NOT(X86_FEATURE_ALWAYS)
+	ALTERNATIVE_2 "jmp .Lskip_rsb_\@", \
+		__stringify(__FILL_RETURN_BUFFER(\reg,\nr)), \ftr, \
+		__stringify(__FILL_ONE_RETURN), \ftr2
+
 .Lskip_rsb_\@:
+.endm
+
+/*
+ * The CALL to srso_alias_untrain_ret() must be patched in directly at
+ * the spot where untraining must be done, ie., srso_alias_untrain_ret()
+ * must be the target of a CALL instruction instead of indirectly
+ * jumping to a wrapper which then calls it. Therefore, this macro is
+ * called outside of __UNTRAIN_RET below, for the time being, before the
+ * kernel can support nested alternatives with arbitrary nesting.
+ */
+.macro CALL_UNTRAIN_RET
+#ifdef CONFIG_CPU_UNRET_ENTRY
+	ALTERNATIVE_2 "", "call entry_untrain_ret", X86_FEATURE_UNRET, \
+		          "call srso_alias_untrain_ret", X86_FEATURE_SRSO_ALIAS
+#endif
+.endm
+
+/*
+ * Mitigate RETBleed for AMD/Hygon Zen uarch. Requires KERNEL CR3 because the
+ * return thunk isn't mapped into the userspace tables (then again, AMD
+ * typically has NO_MELTDOWN).
+ *
+ * While retbleed_untrain_ret() doesn't clobber anything but requires stack,
+ * entry_ibpb() will clobber AX, CX, DX.
+ *
+ * As such, this must be placed after every *SWITCH_TO_KERNEL_CR3 at a point
+ * where we have a stack but before any RET instruction.
+ */
+.macro UNTRAIN_RET
+#if defined(CONFIG_CPU_UNRET_ENTRY) || defined(CONFIG_CPU_IBPB_ENTRY) || \
+	defined(CONFIG_CPU_SRSO)
+	ANNOTATE_UNRET_END
+	CALL_UNTRAIN_RET
+	ALTERNATIVE "", "call entry_ibpb", X86_FEATURE_ENTRY_IBPB
+#endif
+.endm
+
+#ifdef CONFIG_X86_64
+.macro CLEAR_BRANCH_HISTORY
+	ALTERNATIVE "", "call clear_bhb_loop", X86_FEATURE_CLEAR_BHB_LOOP
+.endm
+
+.macro CLEAR_BRANCH_HISTORY_VMEXIT
+	ALTERNATIVE "", "call clear_bhb_loop", X86_FEATURE_CLEAR_BHB_LOOP_ON_VMEXIT
+.endm
+#else
+#define CLEAR_BRANCH_HISTORY
+#define CLEAR_BRANCH_HISTORY_VMEXIT
 #endif
+
+/*
+ * Macro to execute VERW instruction that mitigate transient data sampling
+ * attacks such as MDS. On affected systems a microcode update overloaded VERW
+ * instruction to also clear the CPU buffers. VERW clobbers CFLAGS.ZF.
+ *
+ * Note: Only the memory operand variant of VERW clears the CPU buffers.
+ */
+.macro CLEAR_CPU_BUFFERS
+	ALTERNATIVE "jmp .Lskip_verw_\@", "", X86_FEATURE_CLEAR_CPU_BUF
+#ifdef CONFIG_X86_64
+	verw mds_verw_sel(%rip)
+#else
+	/*
+	 * In 32bit mode, the memory operand must be a %cs reference. The data
+	 * segments may not be usable (vm86 mode), and the stack segment may not
+	 * be flat (ESPFIX32).
+	 */
+	verw %cs:mds_verw_sel
+#endif
+.Lskip_verw_\@:
 .endm
 
 #else /* __ASSEMBLY__ */
@@ -117,7 +233,40 @@
 	_ASM_PTR " 999b\n\t"					\
 	".popsection\n\t"
 
+#ifdef CONFIG_RETHUNK
+extern void __x86_return_thunk(void);
+#else
+static inline void __x86_return_thunk(void) {}
+#endif
+
+extern void retbleed_return_thunk(void);
+extern void srso_return_thunk(void);
+extern void srso_alias_return_thunk(void);
+
+extern void retbleed_untrain_ret(void);
+extern void srso_untrain_ret(void);
+extern void srso_alias_untrain_ret(void);
+
+extern void entry_untrain_ret(void);
+extern void entry_ibpb(void);
+
+extern void (*x86_return_thunk)(void);
+
+#ifdef CONFIG_X86_64
+extern void clear_bhb_loop(void);
+#endif
+
 #ifdef CONFIG_RETPOLINE
+
+typedef u8 retpoline_thunk_t[RETPOLINE_THUNK_SIZE];
+
+#define GEN(reg) \
+	extern retpoline_thunk_t __x86_indirect_thunk_ ## reg;
+#include <asm/GEN-for-each-reg.h>
+#undef GEN
+
+extern retpoline_thunk_t __x86_indirect_thunk_array[];
+
 #ifdef CONFIG_X86_64
 
 /*
@@ -133,7 +282,7 @@
 	"lfence;\n"						\
 	ANNOTATE_RETPOLINE_SAFE					\
 	"call *%[thunk_target]\n",				\
-	X86_FEATURE_RETPOLINE_AMD)
+	X86_FEATURE_RETPOLINE_LFENCE)
 
 # define THUNK_TARGET(addr) [thunk_target] "r" (addr)
 
@@ -163,7 +312,7 @@
 	"lfence;\n"						\
 	ANNOTATE_RETPOLINE_SAFE					\
 	"call *%[thunk_target]\n",				\
-	X86_FEATURE_RETPOLINE_AMD)
+	X86_FEATURE_RETPOLINE_LFENCE)
 
 # define THUNK_TARGET(addr) [thunk_target] "rm" (addr)
 #endif
@@ -175,9 +324,12 @@
 /* The Spectre V2 mitigation variants */
 enum spectre_v2_mitigation {
 	SPECTRE_V2_NONE,
-	SPECTRE_V2_RETPOLINE_GENERIC,
-	SPECTRE_V2_RETPOLINE_AMD,
-	SPECTRE_V2_IBRS_ENHANCED,
+	SPECTRE_V2_RETPOLINE,
+	SPECTRE_V2_LFENCE,
+	SPECTRE_V2_EIBRS,
+	SPECTRE_V2_EIBRS_RETPOLINE,
+	SPECTRE_V2_EIBRS_LFENCE,
+	SPECTRE_V2_IBRS,
 };
 
 /* The indirect branch speculation control variants */
@@ -211,15 +363,18 @@
 		: "memory");
 }
 
+extern u64 x86_pred_cmd;
+
 static inline void indirect_branch_prediction_barrier(void)
 {
-	u64 val = PRED_CMD_IBPB;
-
-	alternative_msr_write(MSR_IA32_PRED_CMD, val, X86_FEATURE_USE_IBPB);
+	alternative_msr_write(MSR_IA32_PRED_CMD, x86_pred_cmd, X86_FEATURE_USE_IBPB);
 }
 
 /* The Intel SPEC CTRL MSR base value cache */
 extern u64 x86_spec_ctrl_base;
+DECLARE_PER_CPU(u64, x86_spec_ctrl_current);
+extern void update_spec_ctrl_cond(u64 val);
+extern u64 spec_ctrl_current(void);
 
 /*
  * With retpoline, we must use IBRS to restrict branch prediction
@@ -229,18 +384,18 @@
  */
 #define firmware_restrict_branch_speculation_start()			\
 do {									\
-	u64 val = x86_spec_ctrl_base | SPEC_CTRL_IBRS;			\
-									\
 	preempt_disable();						\
-	alternative_msr_write(MSR_IA32_SPEC_CTRL, val,			\
+	alternative_msr_write(MSR_IA32_SPEC_CTRL,			\
+			      spec_ctrl_current() | SPEC_CTRL_IBRS,	\
 			      X86_FEATURE_USE_IBRS_FW);			\
+	alternative_msr_write(MSR_IA32_PRED_CMD, PRED_CMD_IBPB,		\
+			      X86_FEATURE_USE_IBPB_FW);			\
 } while (0)
 
 #define firmware_restrict_branch_speculation_end()			\
 do {									\
-	u64 val = x86_spec_ctrl_base;					\
-									\
-	alternative_msr_write(MSR_IA32_SPEC_CTRL, val,			\
+	alternative_msr_write(MSR_IA32_SPEC_CTRL,			\
+			      spec_ctrl_current(),			\
 			      X86_FEATURE_USE_IBRS_FW);			\
 	preempt_enable();						\
 } while (0)
@@ -249,11 +404,14 @@
 DECLARE_STATIC_KEY_FALSE(switch_mm_cond_ibpb);
 DECLARE_STATIC_KEY_FALSE(switch_mm_always_ibpb);
 
-DECLARE_STATIC_KEY_FALSE(mds_user_clear);
 DECLARE_STATIC_KEY_FALSE(mds_idle_clear);
 
 DECLARE_STATIC_KEY_FALSE(switch_mm_cond_l1d_flush);
 
+DECLARE_STATIC_KEY_FALSE(mmio_stale_data_clear);
+
+extern u16 mds_verw_sel;
+
 #include <asm/segment.h>
 
 /**
@@ -280,17 +438,6 @@
 }
 
 /**
- * mds_user_clear_cpu_buffers - Mitigation for MDS and TAA vulnerability
- *
- * Clear CPU buffers if the corresponding static key is enabled
- */
-static __always_inline void mds_user_clear_cpu_buffers(void)
-{
-	if (static_branch_likely(&mds_user_clear))
-		mds_clear_cpu_buffers();
-}
-
-/**
  * mds_idle_clear_cpu_buffers - Mitigation for MDS vulnerability
  *
  * Clear CPU buffers if the corresponding static key is enabled
@@ -303,63 +450,4 @@
 
 #endif /* __ASSEMBLY__ */
 
-/*
- * Below is used in the eBPF JIT compiler and emits the byte sequence
- * for the following assembly:
- *
- * With retpolines configured:
- *
- *    callq do_rop
- *  spec_trap:
- *    pause
- *    lfence
- *    jmp spec_trap
- *  do_rop:
- *    mov %rcx,(%rsp) for x86_64
- *    mov %edx,(%esp) for x86_32
- *    retq
- *
- * Without retpolines configured:
- *
- *    jmp *%rcx for x86_64
- *    jmp *%edx for x86_32
- */
-#ifdef CONFIG_RETPOLINE
-# ifdef CONFIG_X86_64
-#  define RETPOLINE_RCX_BPF_JIT_SIZE	17
-#  define RETPOLINE_RCX_BPF_JIT()				\
-do {								\
-	EMIT1_off32(0xE8, 7);	 /* callq do_rop */		\
-	/* spec_trap: */					\
-	EMIT2(0xF3, 0x90);       /* pause */			\
-	EMIT3(0x0F, 0xAE, 0xE8); /* lfence */			\
-	EMIT2(0xEB, 0xF9);       /* jmp spec_trap */		\
-	/* do_rop: */						\
-	EMIT4(0x48, 0x89, 0x0C, 0x24); /* mov %rcx,(%rsp) */	\
-	EMIT1(0xC3);             /* retq */			\
-} while (0)
-# else /* !CONFIG_X86_64 */
-#  define RETPOLINE_EDX_BPF_JIT()				\
-do {								\
-	EMIT1_off32(0xE8, 7);	 /* call do_rop */		\
-	/* spec_trap: */					\
-	EMIT2(0xF3, 0x90);       /* pause */			\
-	EMIT3(0x0F, 0xAE, 0xE8); /* lfence */			\
-	EMIT2(0xEB, 0xF9);       /* jmp spec_trap */		\
-	/* do_rop: */						\
-	EMIT3(0x89, 0x14, 0x24); /* mov %edx,(%esp) */		\
-	EMIT1(0xC3);             /* ret */			\
-} while (0)
-# endif
-#else /* !CONFIG_RETPOLINE */
-# ifdef CONFIG_X86_64
-#  define RETPOLINE_RCX_BPF_JIT_SIZE	2
-#  define RETPOLINE_RCX_BPF_JIT()				\
-	EMIT2(0xFF, 0xE1);       /* jmp *%rcx */
-# else /* !CONFIG_X86_64 */
-#  define RETPOLINE_EDX_BPF_JIT()				\
-	EMIT2(0xFF, 0xE2)        /* jmp *%edx */
-# endif
-#endif
-
 #endif /* _ASM_X86_NOSPEC_BRANCH_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/numa.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/numa.h
@@ -12,13 +12,6 @@
 
 #define NR_NODE_MEMBLKS		(MAX_NUMNODES*2)
 
-/*
- * Too small node sizes may confuse the VM badly. Usually they
- * result from BIOS bugs. So dont recognize nodes as standalone
- * NUMA entities that have less than this amount of RAM listed:
- */
-#define NODE_MIN_SIZE (4*1024*1024)
-
 extern int numa_off;
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/page.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/page.h
@@ -71,6 +71,16 @@
 extern bool __virt_addr_valid(unsigned long kaddr);
 #define virt_addr_valid(kaddr)	__virt_addr_valid((unsigned long) (kaddr))
 
+static __always_inline u64 __canonical_address(u64 vaddr, u8 vaddr_bits)
+{
+	return ((s64)vaddr << (64 - vaddr_bits)) >> (64 - vaddr_bits);
+}
+
+static __always_inline u64 __is_canonical_address(u64 vaddr, u8 vaddr_bits)
+{
+	return __canonical_address(vaddr, vaddr_bits) == vaddr;
+}
+
 #endif	/* __ASSEMBLY__ */
 
 #include <asm-generic/memory_model.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/page_32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/page_32.h
@@ -43,7 +43,7 @@
 {
 	memcpy(to, from, PAGE_SIZE);
 }
-#endif	/* CONFIG_X86_3DNOW */
+#endif	/* CONFIG_X86_USE_3DNOW */
 #endif	/* !__ASSEMBLY__ */
 
 #endif /* _ASM_X86_PAGE_32_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/page_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/page_64.h
@@ -15,7 +15,7 @@
 extern unsigned long vmalloc_base;
 extern unsigned long vmemmap_base;
 
-static inline unsigned long __phys_addr_nodebug(unsigned long x)
+static __always_inline unsigned long __phys_addr_nodebug(unsigned long x)
 {
 	unsigned long y = x - __START_KERNEL_map;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/page_64_types.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/page_64_types.h
@@ -15,7 +15,7 @@
 #define THREAD_SIZE_ORDER	(2 + KASAN_STACK_ORDER)
 #define THREAD_SIZE  (PAGE_SIZE << THREAD_SIZE_ORDER)
 
-#define EXCEPTION_STACK_ORDER (0 + KASAN_STACK_ORDER)
+#define EXCEPTION_STACK_ORDER (1 + KASAN_STACK_ORDER)
 #define EXCEPTION_STKSZ (PAGE_SIZE << EXCEPTION_STACK_ORDER)
 
 #define IRQ_STACK_ORDER (2 + KASAN_STACK_ORDER)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/paravirt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/paravirt.h
@@ -665,7 +665,7 @@
 	    "call " #func ";"						\
 	    PV_RESTORE_ALL_CALLER_REGS					\
 	    FRAME_END							\
-	    "ret;"							\
+	    ASM_RET							\
 	    ".size " PV_THUNK_NAME(func) ", .-" PV_THUNK_NAME(func) ";"	\
 	    ".popsection")
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pci-direct.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pci-direct.h
@@ -10,9 +10,11 @@
 extern u32 read_pci_config(u8 bus, u8 slot, u8 func, u8 offset);
 extern u8 read_pci_config_byte(u8 bus, u8 slot, u8 func, u8 offset);
 extern u16 read_pci_config_16(u8 bus, u8 slot, u8 func, u8 offset);
+extern u32 pci_early_find_cap(int bus, int slot, int func, int cap);
 extern void write_pci_config(u8 bus, u8 slot, u8 func, u8 offset, u32 val);
 extern void write_pci_config_byte(u8 bus, u8 slot, u8 func, u8 offset, u8 val);
 extern void write_pci_config_16(u8 bus, u8 slot, u8 func, u8 offset, u16 val);
 
+extern unsigned int pci_early_clear_msi;
 extern int early_pci_allowed(void);
 #endif /* _ASM_X86_PCI_DIRECT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pci_x86.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pci_x86.h
@@ -39,6 +39,8 @@
 #define PCI_ROOT_NO_CRS		0x100000
 #define PCI_NOASSIGN_BARS	0x200000
 #define PCI_BIG_ROOT_WINDOW	0x400000
+#define PCI_USE_E820		0x800000
+#define PCI_NO_E820		0x1000000
 
 extern unsigned int pci_probe;
 extern unsigned long pirq_table_addr;
@@ -64,6 +66,8 @@
 
 /* pci-irq.c */
 
+struct pci_dev;
+
 struct irq_info {
 	u8 bus, devfn;			/* Bus, device and function */
 	struct {
@@ -232,3 +236,9 @@
 # define x86_default_pci_init_irq	NULL
 # define x86_default_pci_fixup_irqs	NULL
 #endif
+
+#if defined(CONFIG_PCI) && defined(CONFIG_ACPI)
+extern bool pci_use_e820;
+#else
+#define pci_use_e820 false
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/perf_event.h
@@ -241,6 +241,11 @@
 #define INTEL_PMC_IDX_FIXED_SLOTS	(INTEL_PMC_IDX_FIXED + 3)
 #define INTEL_PMC_MSK_FIXED_SLOTS	(1ULL << INTEL_PMC_IDX_FIXED_SLOTS)
 
+static inline bool use_fixed_pseudo_encoding(u64 code)
+{
+	return !(code & 0xff);
+}
+
 /*
  * We model BTS tracing as another fixed-mode PMC.
  *
@@ -422,8 +427,10 @@
 
 #ifdef CONFIG_X86_LOCAL_APIC
 extern u32 get_ibs_caps(void);
+extern int forward_event_to_ibs(struct perf_event *event);
 #else
 static inline u32 get_ibs_caps(void) { return 0; }
+static inline int forward_event_to_ibs(struct perf_event *event) { return -ENOENT; }
 #endif
 
 #ifdef CONFIG_PERF_EVENTS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pgtable.h
@@ -22,6 +22,7 @@
 #define pgprot_decrypted(prot)	__pgprot(__sme_clr(pgprot_val(prot)))
 
 #ifndef __ASSEMBLY__
+#include <linux/spinlock.h>
 #include <asm/x86_init.h>
 #include <asm/pkru.h>
 #include <asm/fpu/api.h>
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pgtable_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pgtable_64.h
@@ -235,8 +235,8 @@
 
 #define __pte_to_swp_entry(pte)		((swp_entry_t) { pte_val((pte)) })
 #define __pmd_to_swp_entry(pmd)		((swp_entry_t) { pmd_val((pmd)) })
-#define __swp_entry_to_pte(x)		((pte_t) { .pte = (x).val })
-#define __swp_entry_to_pmd(x)		((pmd_t) { .pmd = (x).val })
+#define __swp_entry_to_pte(x)		(__pte((x).val))
+#define __swp_entry_to_pmd(x)		(__pmd((x).val))
 
 extern int kern_addr_valid(unsigned long addr);
 extern void cleanup_highmap(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pgtable_areas.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pgtable_areas.h
@@ -11,6 +11,12 @@
 
 #define CPU_ENTRY_AREA_RO_IDT_VADDR	((void *)CPU_ENTRY_AREA_RO_IDT)
 
-#define CPU_ENTRY_AREA_MAP_SIZE		(CPU_ENTRY_AREA_PER_CPU + CPU_ENTRY_AREA_ARRAY_SIZE - CPU_ENTRY_AREA_BASE)
+#ifdef CONFIG_X86_32
+#define CPU_ENTRY_AREA_MAP_SIZE		(CPU_ENTRY_AREA_PER_CPU +		\
+					 (CPU_ENTRY_AREA_SIZE * NR_CPUS) -	\
+					 CPU_ENTRY_AREA_BASE)
+#else
+#define CPU_ENTRY_AREA_MAP_SIZE		P4D_SIZE
+#endif
 
 #endif /* _ASM_X86_PGTABLE_AREAS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pgtable_types.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pgtable_types.h
@@ -123,11 +123,12 @@
  * instance, and is *not* included in this mask since
  * pte_modify() does modify it.
  */
-#define _PAGE_CHG_MASK	(PTE_PFN_MASK | _PAGE_PCD | _PAGE_PWT |		\
-			 _PAGE_SPECIAL | _PAGE_ACCESSED | _PAGE_DIRTY |	\
-			 _PAGE_SOFT_DIRTY | _PAGE_DEVMAP | _PAGE_ENC |  \
-			 _PAGE_UFFD_WP)
-#define _HPAGE_CHG_MASK (_PAGE_CHG_MASK | _PAGE_PSE)
+#define _COMMON_PAGE_CHG_MASK	(PTE_PFN_MASK | _PAGE_PCD | _PAGE_PWT |	       \
+				 _PAGE_SPECIAL | _PAGE_ACCESSED | _PAGE_DIRTY |\
+				 _PAGE_SOFT_DIRTY | _PAGE_DEVMAP | _PAGE_ENC | \
+				 _PAGE_UFFD_WP)
+#define _PAGE_CHG_MASK	(_COMMON_PAGE_CHG_MASK | _PAGE_PAT)
+#define _HPAGE_CHG_MASK (_COMMON_PAGE_CHG_MASK | _PAGE_PSE | _PAGE_PAT_LARGE)
 
 /*
  * The cache modes defined here are used to translate between pure SW usage
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/pkru.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/pkru.h
@@ -2,10 +2,10 @@
 #ifndef _ASM_X86_PKRU_H
 #define _ASM_X86_PKRU_H
 
-#include <asm/fpu/xstate.h>
+#include <asm/cpufeature.h>
 
-#define PKRU_AD_BIT 0x1
-#define PKRU_WD_BIT 0x2
+#define PKRU_AD_BIT 0x1u
+#define PKRU_WD_BIT 0x2u
 #define PKRU_BITS_PER_PKEY 2
 
 #ifdef CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/processor.h
@@ -196,6 +196,8 @@
 	return BIT_ULL(boot_cpu_data.x86_cache_bits - 1 - PAGE_SHIFT);
 }
 
+void init_cpu_devs(void);
+void get_cpu_vendor(struct cpuinfo_x86 *c);
 extern void early_cpu_init(void);
 extern void identify_boot_cpu(void);
 extern void identify_secondary_cpu(struct cpuinfo_x86 *);
@@ -461,9 +463,6 @@
 DECLARE_PER_CPU(struct irq_stack *, softirq_stack_ptr);
 #endif	/* !X86_64 */
 
-extern unsigned int fpu_kernel_xstate_size;
-extern unsigned int fpu_user_xstate_size;
-
 struct perf_event;
 
 struct thread_struct {
@@ -518,7 +517,7 @@
 	 */
 	unsigned long		iopl_emul;
 
-	unsigned int		sig_on_uaccess_err:1;
+	unsigned int		iopl_warn:1;
 
 	/*
 	 * Protection Keys Register for Userspace.  Loaded immediately on
@@ -537,12 +536,12 @@
 	 */
 };
 
-/* Whitelist the FPU state from the task_struct for hardened usercopy. */
+extern void fpu_thread_struct_whitelist(unsigned long *offset, unsigned long *size);
+
 static inline void arch_thread_struct_whitelist(unsigned long *offset,
 						unsigned long *size)
 {
-	*offset = offsetof(struct thread_struct, fpu.state);
-	*size = fpu_kernel_xstate_size;
+	fpu_thread_struct_whitelist(offset, size);
 }
 
 static inline void
@@ -802,9 +801,13 @@
 #ifdef CONFIG_CPU_SUP_AMD
 extern u32 amd_get_nodes_per_socket(void);
 extern u32 amd_get_highest_perf(void);
+extern bool cpu_has_ibpb_brtype_microcode(void);
+extern void amd_clear_divider(void);
 #else
 static inline u32 amd_get_nodes_per_socket(void)	{ return 0; }
 static inline u32 amd_get_highest_perf(void)		{ return 0; }
+static inline bool cpu_has_ibpb_brtype_microcode(void)	{ return false; }
+static inline void amd_clear_divider(void)		{ }
 #endif
 
 static inline uint32_t hypervisor_cpuid_base(const char *sig, uint32_t leaves)
@@ -833,8 +836,9 @@
 #define xen_set_default_idle 0
 #endif
 
-void stop_this_cpu(void *dummy);
-void microcode_check(void);
+void __noreturn stop_this_cpu(void *dummy);
+void microcode_check(struct cpuinfo_x86 *prev_info);
+void store_cpu_caps(struct cpuinfo_x86 *info);
 
 enum l1tf_mitigations {
 	L1TF_MITIGATION_OFF,
@@ -853,4 +857,24 @@
 	MDS_MITIGATION_VMWERV,
 };
 
+extern bool gds_ucode_mitigated(void);
+
+/*
+ * Make previous memory operations globally visible before
+ * a WRMSR.
+ *
+ * MFENCE makes writes visible, but only affects load/store
+ * instructions.  WRMSR is unfortunately not a load/store
+ * instruction and is unaffected by MFENCE.  The LFENCE ensures
+ * that the WRMSR is not reordered.
+ *
+ * Most WRMSRs are full serializing instructions themselves and
+ * do not require this barrier.  This is only required for the
+ * IA32_TSC_DEADLINE and X2APIC MSRs.
+ */
+static inline void weak_wrmsr_fence(void)
+{
+	alternative("mfence; lfence", "", ALT_NOT(X86_FEATURE_APIC_MSRS_FENCE));
+}
+
 #endif /* _ASM_X86_PROCESSOR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/proto.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/proto.h
@@ -28,10 +28,6 @@
 void __end_entry_SYSENTER_compat(void);
 void entry_SYSCALL_compat(void);
 void entry_SYSCALL_compat_safe_stack(void);
-void entry_INT80_compat(void);
-#ifdef CONFIG_XEN_PV
-void xen_entry_INT80_compat(void);
-#endif
 #endif
 
 void x86_configure_nx(void);
@@ -40,6 +36,6 @@
 extern int reboot_force;
 
 long do_arch_prctl_common(struct task_struct *task, int option,
-			  unsigned long cpuid_enabled);
+			  unsigned long arg2);
 
 #endif /* _ASM_X86_PROTO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/qspinlock_paravirt.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/qspinlock_paravirt.h
@@ -48,7 +48,7 @@
 	"jne   .slowpath;"
 	"pop   %rdx;"
 	FRAME_END
-	"ret;"
+	ASM_RET
 	".slowpath: "
 	"push   %rsi;"
 	"movzbl %al,%esi;"
@@ -56,7 +56,7 @@
 	"pop    %rsi;"
 	"pop    %rdx;"
 	FRAME_END
-	"ret;"
+	ASM_RET
 	".size " PV_UNLOCK ", .-" PV_UNLOCK ";"
 	".popsection");
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/realmode.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/realmode.h
@@ -89,6 +89,7 @@
 }
 
 void reserve_real_mode(void);
+void load_trampoline_pgtable(void);
 
 #endif /* __ASSEMBLY__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/reboot.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/reboot.h
@@ -25,6 +25,8 @@
 #define MRR_BIOS	0
 #define MRR_APM		1
 
+void cpu_emergency_disable_virtualization(void);
+
 typedef void (*nmi_shootdown_cb)(int, struct pt_regs*);
 void nmi_panic_self_stop(struct pt_regs *regs);
 void nmi_shootdown_cpus(nmi_shootdown_cb callback);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/required-features.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/required-features.h
@@ -102,6 +102,8 @@
 #define REQUIRED_MASK17	0
 #define REQUIRED_MASK18	0
 #define REQUIRED_MASK19	0
-#define REQUIRED_MASK_CHECK BUILD_BUG_ON_ZERO(NCAPINTS != 20)
+#define REQUIRED_MASK20	0
+#define REQUIRED_MASK21	0
+#define REQUIRED_MASK_CHECK BUILD_BUG_ON_ZERO(NCAPINTS != 22)
 
 #endif /* _ASM_X86_REQUIRED_FEATURES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/resctrl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/resctrl.h
@@ -51,7 +51,7 @@
  *   simple as possible.
  * Must be called with preemption disabled.
  */
-static void __resctrl_sched_in(void)
+static inline void __resctrl_sched_in(struct task_struct *tsk)
 {
 	struct resctrl_pqr_state *state = this_cpu_ptr(&pqr_state);
 	u32 closid = state->default_closid;
@@ -63,13 +63,13 @@
 	 * Else use the closid/rmid assigned to this cpu.
 	 */
 	if (static_branch_likely(&rdt_alloc_enable_key)) {
-		tmp = READ_ONCE(current->closid);
+		tmp = READ_ONCE(tsk->closid);
 		if (tmp)
 			closid = tmp;
 	}
 
 	if (static_branch_likely(&rdt_mon_enable_key)) {
-		tmp = READ_ONCE(current->rmid);
+		tmp = READ_ONCE(tsk->rmid);
 		if (tmp)
 			rmid = tmp;
 	}
@@ -81,17 +81,17 @@
 	}
 }
 
-static inline void resctrl_sched_in(void)
+static inline void resctrl_sched_in(struct task_struct *tsk)
 {
 	if (static_branch_likely(&rdt_enable_key))
-		__resctrl_sched_in();
+		__resctrl_sched_in(tsk);
 }
 
 void resctrl_cpu_detect(struct cpuinfo_x86 *c);
 
 #else
 
-static inline void resctrl_sched_in(void) {}
+static inline void resctrl_sched_in(struct task_struct *tsk) {}
 static inline void resctrl_cpu_detect(struct cpuinfo_x86 *c) {}
 
 #endif /* CONFIG_X86_CPU_RESCTRL */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/segment.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/segment.h
@@ -339,7 +339,7 @@
 		     "1:	movw %0, %%fs			\n"
 		     "2:					\n"
 
-		     _ASM_EXTABLE_HANDLE(1b, 2b, ex_handler_clear_fs)
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_CLEAR_FS)
 
 		     : : "rm" (value) : "memory");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/setup.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/setup.h
@@ -108,27 +108,16 @@
 void *extend_brk(size_t size, size_t align);
 
 /*
- * Reserve space in the brk section.  The name must be unique within
- * the file, and somewhat descriptive.  The size is in bytes.  Must be
- * used at file scope.
+ * Reserve space in the .brk section, which is a block of memory from which the
+ * caller is allowed to allocate very early (before even memblock is available)
+ * by calling extend_brk().  All allocated memory will be eventually converted
+ * to memblock.  Any leftover unallocated memory will be freed.
  *
- * (This uses a temp function to wrap the asm so we can pass it the
- * size parameter; otherwise we wouldn't be able to.  We can't use a
- * "section" attribute on a normal variable because it always ends up
- * being @progbits, which ends up allocating space in the vmlinux
- * executable.)
+ * The size is in bytes.
  */
-#define RESERVE_BRK(name,sz)						\
-	static void __section(".discard.text") __used notrace		\
-	__brk_reservation_fn_##name##__(void) {				\
-		asm volatile (						\
-			".pushsection .brk_reservation,\"aw\",@nobits;" \
-			".brk." #name ":"				\
-			" 1:.skip %c0;"					\
-			" .size .brk." #name ", . - 1b;"		\
-			" .popsection"					\
-			: : "i" (sz));					\
-	}
+#define RESERVE_BRK(name, size)					\
+	__section(".bss..brk") __aligned(1) __used	\
+	static char __brk_##name[size]
 
 extern void probe_roms(void);
 #ifdef __i386__
@@ -141,12 +130,19 @@
 
 #endif /* __i386__ */
 #endif /* _SETUP */
-#else
-#define RESERVE_BRK(name,sz)				\
-	.pushsection .brk_reservation,"aw",@nobits;	\
-.brk.name:						\
-1:	.skip sz;					\
-	.size .brk.name,.-1b;				\
+
+#else  /* __ASSEMBLY */
+
+.macro __RESERVE_BRK name, size
+	.pushsection .bss..brk, "aw"
+SYM_DATA_START(__brk_\name)
+	.skip \size
+SYM_DATA_END(__brk_\name)
 	.popsection
+.endm
+
+#define RESERVE_BRK(name, size) __RESERVE_BRK name, size
+
 #endif /* __ASSEMBLY__ */
+
 #endif /* _ASM_X86_SETUP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/sev-common.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/sev-common.h
@@ -73,4 +73,15 @@
 
 #define GHCB_RESP_CODE(v)		((v) & GHCB_MSR_INFO_MASK)
 
+/*
+ * Error codes related to GHCB input that can be communicated back to the guest
+ * by setting the lower 32-bits of the GHCB SW_EXITINFO1 field to 2.
+ */
+#define GHCB_ERR_NOT_REGISTERED		1
+#define GHCB_ERR_INVALID_USAGE		2
+#define GHCB_ERR_INVALID_SCRATCH_AREA	3
+#define GHCB_ERR_MISSING_INPUT		4
+#define GHCB_ERR_INVALID_INPUT		5
+#define GHCB_ERR_INVALID_EVENT		6
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/sigframe.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/sigframe.h
@@ -85,6 +85,4 @@
 
 #endif /* CONFIG_X86_64 */
 
-void __init init_sigframe_size(void);
-
 #endif /* _ASM_X86_SIGFRAME_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/special_insns.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/special_insns.h
@@ -224,7 +224,7 @@
 
 #define nop() asm volatile ("nop")
 
-static inline void serialize(void)
+static __always_inline void serialize(void)
 {
 	/* Instruction opcode for SERIALIZE; supported in binutils >= 2.35. */
 	asm volatile(".byte 0xf, 0x1, 0xe8" ::: "memory");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/stacktrace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/stacktrace.h
@@ -38,6 +38,16 @@
 bool get_stack_info_noinstr(unsigned long *stack, struct task_struct *task,
 			    struct stack_info *info);
 
+static __always_inline
+bool get_stack_guard_info(unsigned long *stack, struct stack_info *info)
+{
+	/* make sure it's not in the stack proper */
+	if (get_stack_info_noinstr(stack, current, info))
+		return false;
+	/* but if it is in the page below it, we hit a guard */
+	return get_stack_info_noinstr((void *)stack + PAGE_SIZE, current, info);
+}
+
 const char *stack_type_name(enum stack_type type);
 
 static inline bool on_stack(struct stack_info *info, void *addr, size_t len)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/static_call.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/static_call.h
@@ -21,6 +21,16 @@
  * relative displacement across sections.
  */
 
+/*
+ * The trampoline is 8 bytes and of the general form:
+ *
+ *   jmp.d32 \func
+ *   ud1 %esp, %ecx
+ *
+ * That trailing #UD provides both a speculation stop and serves as a unique
+ * 3 byte signature identifying static call trampolines. Also see tramp_ud[]
+ * and __static_call_fixup().
+ */
 #define __ARCH_DEFINE_STATIC_CALL_TRAMP(name, insns)			\
 	asm(".pushsection .static_call.text, \"ax\"		\n"	\
 	    ".align 4						\n"	\
@@ -34,8 +44,13 @@
 #define ARCH_DEFINE_STATIC_CALL_TRAMP(name, func)			\
 	__ARCH_DEFINE_STATIC_CALL_TRAMP(name, ".byte 0xe9; .long " #func " - (. + 4)")
 
+#ifdef CONFIG_RETHUNK
+#define ARCH_DEFINE_STATIC_CALL_NULL_TRAMP(name)			\
+	__ARCH_DEFINE_STATIC_CALL_TRAMP(name, "jmp __x86_return_thunk")
+#else
 #define ARCH_DEFINE_STATIC_CALL_NULL_TRAMP(name)			\
-	__ARCH_DEFINE_STATIC_CALL_TRAMP(name, "ret; nop; nop; nop; nop")
+	__ARCH_DEFINE_STATIC_CALL_TRAMP(name, "ret; int3; nop; nop; nop")
+#endif
 
 
 #define ARCH_ADD_TRAMP_KEY(name)					\
@@ -44,4 +59,21 @@
 	    ".long " STATIC_CALL_KEY_STR(name) " - .		\n"	\
 	    ".popsection					\n")
 
+extern bool __static_call_fixup(void *tramp, u8 op, void *dest);
+
+extern void __static_call_update_early(void *tramp, void *func);
+
+#define static_call_update_early(name, _func)				\
+({									\
+	typeof(&STATIC_CALL_TRAMP(name)) __F = (_func);			\
+	if (static_call_initialized) {					\
+		__static_call_update(&STATIC_CALL_KEY(name),		\
+				     STATIC_CALL_TRAMP_ADDR(name), __F);\
+	} else {							\
+		WRITE_ONCE(STATIC_CALL_KEY(name).func, _func);		\
+		__static_call_update_early(STATIC_CALL_TRAMP_ADDR(name),\
+					   __F);			\
+	}								\
+})
+
 #endif /* _ASM_STATIC_CALL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/suspend_32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/suspend_32.h
@@ -12,14 +12,8 @@
 
 /* image of the saved processor state */
 struct saved_context {
-	/*
-	 * On x86_32, all segment registers except gs are saved at kernel
-	 * entry in pt_regs.
-	 */
-	u16 gs;
 	unsigned long cr0, cr2, cr3, cr4;
 	u64 misc_enable;
-	bool misc_enable_saved;
 	struct saved_msrs saved_msrs;
 	struct desc_ptr gdt_desc;
 	struct desc_ptr idt;
@@ -28,6 +22,12 @@
 	unsigned long tr;
 	unsigned long safety;
 	unsigned long return_address;
+	/*
+	 * On x86_32, all segment registers except gs are saved at kernel
+	 * entry in pt_regs.
+	 */
+	u16 gs;
+	bool misc_enable_saved;
 } __attribute__((packed));
 
 /* routines for saving/restoring kernel state */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/suspend_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/suspend_64.h
@@ -14,9 +14,13 @@
  * Image of the saved processor state, used by the low level ACPI suspend to
  * RAM code and by the low level hibernation code.
  *
- * If you modify it, fix arch/x86/kernel/acpi/wakeup_64.S and make sure that
- * __save/__restore_processor_state(), defined in arch/x86/kernel/suspend_64.c,
- * still work as required.
+ * If you modify it, check how it is used in arch/x86/kernel/acpi/wakeup_64.S
+ * and make sure that __save/__restore_processor_state(), defined in
+ * arch/x86/power/cpu.c, still work as required.
+ *
+ * Because the structure is packed, make sure to avoid unaligned members. For
+ * optimisation purposes but also because tools like kmemleak only search for
+ * pointers that are aligned.
  */
 struct saved_context {
 	struct pt_regs regs;
@@ -36,7 +40,6 @@
 
 	unsigned long cr0, cr2, cr3, cr4;
 	u64 misc_enable;
-	bool misc_enable_saved;
 	struct saved_msrs saved_msrs;
 	unsigned long efer;
 	u16 gdt_pad; /* Unused */
@@ -48,6 +51,7 @@
 	unsigned long tr;
 	unsigned long safety;
 	unsigned long return_address;
+	bool misc_enable_saved;
 } __attribute__((packed));
 
 #define loaddebug(thread,register) \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/sync_core.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/sync_core.h
@@ -8,7 +8,7 @@
 #include <asm/special_insns.h>
 
 #ifdef CONFIG_X86_32
-static inline void iret_to_self(void)
+static __always_inline void iret_to_self(void)
 {
 	asm volatile (
 		"pushfl\n\t"
@@ -19,7 +19,7 @@
 		: ASM_CALL_CONSTRAINT : : "memory");
 }
 #else
-static inline void iret_to_self(void)
+static __always_inline void iret_to_self(void)
 {
 	unsigned int tmp;
 
@@ -55,7 +55,7 @@
  * Like all of Linux's memory ordering operations, this is a
  * compiler barrier as well.
  */
-static inline void sync_core(void)
+static __always_inline void sync_core(void)
 {
 	/*
 	 * The SERIALIZE instruction is the most straightforward way to
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/syscall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/syscall.h
@@ -16,19 +16,17 @@
 #include <asm/thread_info.h>	/* for TS_COMPAT */
 #include <asm/unistd.h>
 
+/* This is used purely for kernel/trace/trace_syscalls.c */
 typedef long (*sys_call_ptr_t)(const struct pt_regs *);
 extern const sys_call_ptr_t sys_call_table[];
 
-#if defined(CONFIG_X86_32)
-#define ia32_sys_call_table sys_call_table
-#else
 /*
  * These may not exist, but still put the prototypes in so we
  * can use IS_ENABLED().
  */
-extern const sys_call_ptr_t ia32_sys_call_table[];
-extern const sys_call_ptr_t x32_sys_call_table[];
-#endif
+extern long ia32_sys_call(const struct pt_regs *, unsigned int nr);
+extern long x32_sys_call(const struct pt_regs *, unsigned int nr);
+extern long x64_sys_call(const struct pt_regs *, unsigned int nr);
 
 /*
  * Only the low 32 bits of orig_ax are meaningful, so we return int.
@@ -84,7 +82,12 @@
 					 struct pt_regs *regs,
 					 unsigned long *args)
 {
-	memcpy(args, &regs->bx, 6 * sizeof(args[0]));
+	args[0] = regs->bx;
+	args[1] = regs->cx;
+	args[2] = regs->dx;
+	args[3] = regs->si;
+	args[4] = regs->di;
+	args[5] = regs->bp;
 }
 
 static inline void syscall_set_arguments(struct task_struct *task,
@@ -160,9 +163,12 @@
 }
 
 void do_syscall_64(struct pt_regs *regs, int nr);
-void do_int80_syscall_32(struct pt_regs *regs);
-long do_fast_syscall_32(struct pt_regs *regs);
+void do_int80_emulation(struct pt_regs *regs);
 
 #endif	/* CONFIG_X86_32 */
 
+void do_int80_syscall_32(struct pt_regs *regs);
+long do_fast_syscall_32(struct pt_regs *regs);
+long do_SYSENTER_32(struct pt_regs *regs);
+
 #endif	/* _ASM_X86_SYSCALL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/syscall_wrapper.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/syscall_wrapper.h
@@ -6,7 +6,7 @@
 #ifndef _ASM_X86_SYSCALL_WRAPPER_H
 #define _ASM_X86_SYSCALL_WRAPPER_H
 
-struct pt_regs;
+#include <asm/ptrace.h>
 
 extern long __x64_sys_ni_syscall(const struct pt_regs *regs);
 extern long __ia32_sys_ni_syscall(const struct pt_regs *regs);
@@ -58,12 +58,29 @@
 		,,regs->di,,regs->si,,regs->dx				\
 		,,regs->r10,,regs->r8,,regs->r9)			\
 
+
+/* SYSCALL_PT_ARGS is Adapted from s390x */
+#define SYSCALL_PT_ARG6(m, t1, t2, t3, t4, t5, t6)			\
+	SYSCALL_PT_ARG5(m, t1, t2, t3, t4, t5), m(t6, (regs->bp))
+#define SYSCALL_PT_ARG5(m, t1, t2, t3, t4, t5)				\
+	SYSCALL_PT_ARG4(m, t1, t2, t3, t4),  m(t5, (regs->di))
+#define SYSCALL_PT_ARG4(m, t1, t2, t3, t4)				\
+	SYSCALL_PT_ARG3(m, t1, t2, t3),  m(t4, (regs->si))
+#define SYSCALL_PT_ARG3(m, t1, t2, t3)					\
+	SYSCALL_PT_ARG2(m, t1, t2), m(t3, (regs->dx))
+#define SYSCALL_PT_ARG2(m, t1, t2)					\
+	SYSCALL_PT_ARG1(m, t1), m(t2, (regs->cx))
+#define SYSCALL_PT_ARG1(m, t1) m(t1, (regs->bx))
+#define SYSCALL_PT_ARGS(x, ...) SYSCALL_PT_ARG##x(__VA_ARGS__)
+
+#define __SC_COMPAT_CAST(t, a)						\
+	(__typeof(__builtin_choose_expr(__TYPE_IS_L(t), 0, 0U)))	\
+	(unsigned int)a
+
 /* Mapping of registers to parameters for syscalls on i386 */
 #define SC_IA32_REGS_TO_ARGS(x, ...)					\
-	__MAP(x,__SC_ARGS						\
-	      ,,(unsigned int)regs->bx,,(unsigned int)regs->cx		\
-	      ,,(unsigned int)regs->dx,,(unsigned int)regs->si		\
-	      ,,(unsigned int)regs->di,,(unsigned int)regs->bp)
+	SYSCALL_PT_ARGS(x, __SC_COMPAT_CAST,				\
+			__MAP(x, __SC_TYPE, __VA_ARGS__))		\
 
 #define __SYS_STUB0(abi, name)						\
 	long __##abi##_##name(const struct pt_regs *regs);		\
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/text-patching.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/text-patching.h
@@ -96,24 +96,40 @@
 };
 
 static __always_inline
-void *text_gen_insn(u8 opcode, const void *addr, const void *dest)
+void __text_gen_insn(void *buf, u8 opcode, const void *addr, const void *dest, int size)
 {
-	static union text_poke_insn insn; /* per instance */
-	int size = text_opcode_size(opcode);
+	union text_poke_insn *insn = buf;
+
+	BUG_ON(size < text_opcode_size(opcode));
+
+	/*
+	 * Hide the addresses to avoid the compiler folding in constants when
+	 * referencing code, these can mess up annotations like
+	 * ANNOTATE_NOENDBR.
+	 */
+	OPTIMIZER_HIDE_VAR(insn);
+	OPTIMIZER_HIDE_VAR(addr);
+	OPTIMIZER_HIDE_VAR(dest);
 
-	insn.opcode = opcode;
+	insn->opcode = opcode;
 
 	if (size > 1) {
-		insn.disp = (long)dest - (long)(addr + size);
+		insn->disp = (long)dest - (long)(addr + size);
 		if (size == 2) {
 			/*
-			 * Ensure that for JMP9 the displacement
+			 * Ensure that for JMP8 the displacement
 			 * actually fits the signed byte.
 			 */
-			BUG_ON((insn.disp >> 31) != (insn.disp >> 7));
+			BUG_ON((insn->disp >> 31) != (insn->disp >> 7));
 		}
 	}
+}
 
+static __always_inline
+void *text_gen_insn(u8 opcode, const void *addr, const void *dest)
+{
+	static union text_poke_insn insn; /* per instance */
+	__text_gen_insn(&insn, opcode, addr, dest, text_opcode_size(opcode));
 	return &insn.text;
 }
 
@@ -165,6 +181,37 @@
 	unsigned long ip = int3_emulate_pop(regs);
 	int3_emulate_jmp(regs, ip);
 }
+
+static __always_inline
+void int3_emulate_jcc(struct pt_regs *regs, u8 cc, unsigned long ip, unsigned long disp)
+{
+	static const unsigned long jcc_mask[6] = {
+		[0] = X86_EFLAGS_OF,
+		[1] = X86_EFLAGS_CF,
+		[2] = X86_EFLAGS_ZF,
+		[3] = X86_EFLAGS_CF | X86_EFLAGS_ZF,
+		[4] = X86_EFLAGS_SF,
+		[5] = X86_EFLAGS_PF,
+	};
+
+	bool invert = cc & 1;
+	bool match;
+
+	if (cc < 0xc) {
+		match = regs->flags & jcc_mask[cc >> 1];
+	} else {
+		match = ((regs->flags & X86_EFLAGS_SF) >> X86_EFLAGS_SF_BIT) ^
+			((regs->flags & X86_EFLAGS_OF) >> X86_EFLAGS_OF_BIT);
+		if (cc >= 0xe)
+			match = match || (regs->flags & X86_EFLAGS_ZF);
+	}
+
+	if ((match && !invert) || (!match && invert))
+		ip += disp;
+
+	int3_emulate_jmp(regs, ip);
+}
+
 #endif /* !CONFIG_UML_X86 */
 
 #endif /* _ASM_X86_TEXT_PATCHING_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/timex.h
@@ -5,6 +5,15 @@
 #include <asm/processor.h>
 #include <asm/tsc.h>
 
+static inline unsigned long random_get_entropy(void)
+{
+	if (!IS_ENABLED(CONFIG_X86_TSC) &&
+	    !cpu_feature_enabled(X86_FEATURE_TSC))
+		return random_get_entropy_fallback();
+	return rdtsc();
+}
+#define random_get_entropy random_get_entropy
+
 /* Assume we use the PIT time source for the clock tick */
 #define CLOCK_TICK_RATE		PIT_TICK_RATE
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/tlbflush.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/tlbflush.h
@@ -207,6 +207,7 @@
 	unsigned int		initiating_cpu;
 	u8			stride_shift;
 	u8			freed_tables;
+	u8			trim_cpumask;
 };
 
 void flush_tlb_local(void);
@@ -226,7 +227,7 @@
 	flush_tlb_mm_range((vma)->vm_mm, start, end,			\
 			   ((vma)->vm_flags & VM_HUGETLB)		\
 				? huge_page_shift(hstate_vma(vma))	\
-				: PAGE_SHIFT, false)
+				: PAGE_SHIFT, true)
 
 extern void flush_tlb_all(void);
 extern void flush_tlb_mm_range(struct mm_struct *mm, unsigned long start,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/topology.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/topology.h
@@ -218,7 +218,7 @@
 }
 #endif
 
-#ifdef CONFIG_ACPI_CPPC_LIB
+#if defined(CONFIG_ACPI_CPPC_LIB) && defined(CONFIG_SMP)
 void init_freq_invariance_cppc(void);
 #define init_freq_invariance_cppc init_freq_invariance_cppc
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/trace/fpu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/trace/fpu.h
@@ -22,8 +22,8 @@
 		__entry->fpu		= fpu;
 		__entry->load_fpu	= test_thread_flag(TIF_NEED_FPU_LOAD);
 		if (boot_cpu_has(X86_FEATURE_OSXSAVE)) {
-			__entry->xfeatures = fpu->state.xsave.header.xfeatures;
-			__entry->xcomp_bv  = fpu->state.xsave.header.xcomp_bv;
+			__entry->xfeatures = fpu->fpstate->regs.xsave.header.xfeatures;
+			__entry->xcomp_bv  = fpu->fpstate->regs.xsave.header.xcomp_bv;
 		}
 	),
 	TP_printk("x86/fpu: %p load: %d xfeatures: %llx xcomp_bv: %llx",
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/traps.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/traps.h
@@ -13,7 +13,7 @@
 #ifdef CONFIG_X86_64
 asmlinkage __visible notrace struct pt_regs *sync_regs(struct pt_regs *eregs);
 asmlinkage __visible notrace
-struct bad_iret_stack *fixup_bad_iret(struct bad_iret_stack *s);
+struct pt_regs *fixup_bad_iret(struct pt_regs *bad_regs);
 void __init trap_init(void);
 asmlinkage __visible noinstr struct pt_regs *vc_switch_off_ist(struct pt_regs *eregs);
 #endif
@@ -40,9 +40,9 @@
 bool fault_in_kernel_space(unsigned long address);
 
 #ifdef CONFIG_VMAP_STACK
-void __noreturn handle_stack_overflow(const char *message,
-				      struct pt_regs *regs,
-				      unsigned long fault_address);
+void __noreturn handle_stack_overflow(struct pt_regs *regs,
+				      unsigned long fault_address,
+				      struct stack_info *info);
 #endif
 
 #endif /* _ASM_X86_TRAPS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/tsc.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/tsc.h
@@ -20,13 +20,12 @@
 
 static inline cycles_t get_cycles(void)
 {
-#ifndef CONFIG_X86_TSC
-	if (!boot_cpu_has(X86_FEATURE_TSC))
+	if (!IS_ENABLED(CONFIG_X86_TSC) &&
+	    !cpu_feature_enabled(X86_FEATURE_TSC))
 		return 0;
-#endif
-
 	return rdtsc();
 }
+#define get_cycles get_cycles
 
 extern struct system_counterval_t convert_art_to_tsc(u64 art);
 extern struct system_counterval_t convert_art_ns_to_tsc(u64 art_ns);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/uaccess.h
@@ -314,11 +314,12 @@
 do {									\
 	__chk_user_ptr(ptr);						\
 	switch (size) {							\
-	unsigned char x_u8__;						\
-	case 1:								\
+	case 1:	{							\
+		unsigned char x_u8__;					\
 		__get_user_asm(x_u8__, ptr, "b", "=q", label);		\
 		(x) = x_u8__;						\
 		break;							\
+	}								\
 	case 2:								\
 		__get_user_asm(x, ptr, "w", "=r", label);		\
 		break;							\
@@ -411,7 +412,104 @@
 		     : [umem] "m" (__m(addr)),				\
 		       [efault] "i" (-EFAULT), "0" (err))
 
-#endif // CONFIG_CC_ASM_GOTO_OUTPUT
+#endif // CONFIG_CC_HAS_ASM_GOTO_OUTPUT
+
+#ifdef CONFIG_CC_HAS_ASM_GOTO_TIED_OUTPUT
+#define __try_cmpxchg_user_asm(itype, ltype, _ptr, _pold, _new, label)	({ \
+	bool success;							\
+	__typeof__(_ptr) _old = (__typeof__(_ptr))(_pold);		\
+	__typeof__(*(_ptr)) __old = *_old;				\
+	__typeof__(*(_ptr)) __new = (_new);				\
+	asm_volatile_goto("\n"						\
+		     "1: " LOCK_PREFIX "cmpxchg"itype" %[new], %[ptr]\n"\
+		     _ASM_EXTABLE_UA(1b, %l[label])			\
+		     : CC_OUT(z) (success),				\
+		       [ptr] "+m" (*_ptr),				\
+		       [old] "+a" (__old)				\
+		     : [new] ltype (__new)				\
+		     : "memory"						\
+		     : label);						\
+	if (unlikely(!success))						\
+		*_old = __old;						\
+	likely(success);					})
+
+#ifdef CONFIG_X86_32
+#define __try_cmpxchg64_user_asm(_ptr, _pold, _new, label)	({	\
+	bool success;							\
+	__typeof__(_ptr) _old = (__typeof__(_ptr))(_pold);		\
+	__typeof__(*(_ptr)) __old = *_old;				\
+	__typeof__(*(_ptr)) __new = (_new);				\
+	asm_volatile_goto("\n"						\
+		     "1: " LOCK_PREFIX "cmpxchg8b %[ptr]\n"		\
+		     _ASM_EXTABLE_UA(1b, %l[label])			\
+		     : CC_OUT(z) (success),				\
+		       "+A" (__old),					\
+		       [ptr] "+m" (*_ptr)				\
+		     : "b" ((u32)__new),				\
+		       "c" ((u32)((u64)__new >> 32))			\
+		     : "memory"						\
+		     : label);						\
+	if (unlikely(!success))						\
+		*_old = __old;						\
+	likely(success);					})
+#endif // CONFIG_X86_32
+#else  // !CONFIG_CC_HAS_ASM_GOTO_TIED_OUTPUT
+#define __try_cmpxchg_user_asm(itype, ltype, _ptr, _pold, _new, label)	({ \
+	int __err = 0;							\
+	bool success;							\
+	__typeof__(_ptr) _old = (__typeof__(_ptr))(_pold);		\
+	__typeof__(*(_ptr)) __old = *_old;				\
+	__typeof__(*(_ptr)) __new = (_new);				\
+	asm volatile("\n"						\
+		     "1: " LOCK_PREFIX "cmpxchg"itype" %[new], %[ptr]\n"\
+		     CC_SET(z)						\
+		     "2:\n"						\
+		     _ASM_EXTABLE_TYPE_REG(1b, 2b, EX_TYPE_EFAULT_REG,	\
+					   %[errout])			\
+		     : CC_OUT(z) (success),				\
+		       [errout] "+r" (__err),				\
+		       [ptr] "+m" (*_ptr),				\
+		       [old] "+a" (__old)				\
+		     : [new] ltype (__new)				\
+		     : "memory");					\
+	if (unlikely(__err))						\
+		goto label;						\
+	if (unlikely(!success))						\
+		*_old = __old;						\
+	likely(success);					})
+
+#ifdef CONFIG_X86_32
+/*
+ * Unlike the normal CMPXCHG, hardcode ECX for both success/fail and error.
+ * There are only six GPRs available and four (EAX, EBX, ECX, and EDX) are
+ * hardcoded by CMPXCHG8B, leaving only ESI and EDI.  If the compiler uses
+ * both ESI and EDI for the memory operand, compilation will fail if the error
+ * is an input+output as there will be no register available for input.
+ */
+#define __try_cmpxchg64_user_asm(_ptr, _pold, _new, label)	({	\
+	int __result;							\
+	__typeof__(_ptr) _old = (__typeof__(_ptr))(_pold);		\
+	__typeof__(*(_ptr)) __old = *_old;				\
+	__typeof__(*(_ptr)) __new = (_new);				\
+	asm volatile("\n"						\
+		     "1: " LOCK_PREFIX "cmpxchg8b %[ptr]\n"		\
+		     "mov $0, %%ecx\n\t"				\
+		     "setz %%cl\n"					\
+		     "2:\n"						\
+		     _ASM_EXTABLE_TYPE_REG(1b, 2b, EX_TYPE_EFAULT_REG, %%ecx) \
+		     : [result]"=c" (__result),				\
+		       "+A" (__old),					\
+		       [ptr] "+m" (*_ptr)				\
+		     : "b" ((u32)__new),				\
+		       "c" ((u32)((u64)__new >> 32))			\
+		     : "memory", "cc");					\
+	if (unlikely(__result < 0))					\
+		goto label;						\
+	if (unlikely(!__result))					\
+		*_old = __old;						\
+	likely(__result);					})
+#endif // CONFIG_X86_32
+#endif // CONFIG_CC_HAS_ASM_GOTO_TIED_OUTPUT
 
 /* FIXME: this hack is definitely wrong -AK */
 struct __large_struct { unsigned long buf[100]; };
@@ -445,7 +543,7 @@
 #define copy_mc_to_kernel copy_mc_to_kernel
 
 unsigned long __must_check
-copy_mc_to_user(void *to, const void *from, unsigned len);
+copy_mc_to_user(void __user *to, const void *from, unsigned len);
 #endif
 
 /*
@@ -505,6 +603,51 @@
 } while (0)
 #endif // CONFIG_CC_HAS_ASM_GOTO_OUTPUT
 
+extern void __try_cmpxchg_user_wrong_size(void);
+
+#ifndef CONFIG_X86_32
+#define __try_cmpxchg64_user_asm(_ptr, _oldp, _nval, _label)		\
+	__try_cmpxchg_user_asm("q", "r", (_ptr), (_oldp), (_nval), _label)
+#endif
+
+/*
+ * Force the pointer to u<size> to match the size expected by the asm helper.
+ * clang/LLVM compiles all cases and only discards the unused paths after
+ * processing errors, which breaks i386 if the pointer is an 8-byte value.
+ */
+#define unsafe_try_cmpxchg_user(_ptr, _oldp, _nval, _label) ({			\
+	bool __ret;								\
+	__chk_user_ptr(_ptr);							\
+	switch (sizeof(*(_ptr))) {						\
+	case 1:	__ret = __try_cmpxchg_user_asm("b", "q",			\
+					       (__force u8 *)(_ptr), (_oldp),	\
+					       (_nval), _label);		\
+		break;								\
+	case 2:	__ret = __try_cmpxchg_user_asm("w", "r",			\
+					       (__force u16 *)(_ptr), (_oldp),	\
+					       (_nval), _label);		\
+		break;								\
+	case 4:	__ret = __try_cmpxchg_user_asm("l", "r",			\
+					       (__force u32 *)(_ptr), (_oldp),	\
+					       (_nval), _label);		\
+		break;								\
+	case 8:	__ret = __try_cmpxchg64_user_asm((__force u64 *)(_ptr), (_oldp),\
+						 (_nval), _label);		\
+		break;								\
+	default: __try_cmpxchg_user_wrong_size();				\
+	}									\
+	__ret;						})
+
+/* "Returns" 0 on success, 1 on failure, -EFAULT if the access faults. */
+#define __try_cmpxchg_user(_ptr, _oldp, _nval, _label)	({		\
+	int __ret = -EFAULT;						\
+	__uaccess_begin_nospec();					\
+	__ret = !unsafe_try_cmpxchg_user(_ptr, _oldp, _nval, _label);	\
+_label:									\
+	__uaccess_end();						\
+	__ret;								\
+							})
+
 /*
  * We want the unsafe accessors to always be inlined and use
  * the error labels - thus the macro games.
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/unwind_hints.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/unwind_hints.h
@@ -8,7 +8,11 @@
 #ifdef __ASSEMBLY__
 
 .macro UNWIND_HINT_EMPTY
-	UNWIND_HINT sp_reg=ORC_REG_UNDEFINED type=UNWIND_HINT_TYPE_CALL end=1
+	UNWIND_HINT type=UNWIND_HINT_TYPE_CALL end=1
+.endm
+
+.macro UNWIND_HINT_ENTRY
+	UNWIND_HINT type=UNWIND_HINT_TYPE_ENTRY end=1
 .endm
 
 .macro UNWIND_HINT_REGS base=%rsp offset=0 indirect=0 extra=1 partial=0
@@ -52,6 +56,14 @@
 	UNWIND_HINT sp_reg=ORC_REG_SP sp_offset=8 type=UNWIND_HINT_TYPE_FUNC
 .endm
 
+.macro UNWIND_HINT_SAVE
+	UNWIND_HINT type=UNWIND_HINT_TYPE_SAVE
+.endm
+
+.macro UNWIND_HINT_RESTORE
+	UNWIND_HINT type=UNWIND_HINT_TYPE_RESTORE
+.endm
+
 #endif /* __ASSEMBLY__ */
 
 #endif /* _ASM_X86_UNWIND_HINTS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/virtext.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/virtext.h
@@ -101,12 +101,6 @@
 		return 0;
 	}
 
-	if (boot_cpu_data.extended_cpuid_level < SVM_CPUID_FUNC) {
-		if (msg)
-			*msg = "can't execute cpuid_8000000a";
-		return 0;
-	}
-
 	if (!boot_cpu_has(X86_FEATURE_SVM)) {
 		if (msg)
 			*msg = "svm not available";
@@ -126,7 +120,21 @@
 
 	wrmsrl(MSR_VM_HSAVE_PA, 0);
 	rdmsrl(MSR_EFER, efer);
-	wrmsrl(MSR_EFER, efer & ~EFER_SVME);
+	if (efer & EFER_SVME) {
+		/*
+		 * Force GIF=1 prior to disabling SVM to ensure INIT and NMI
+		 * aren't blocked, e.g. if a fatal error occurred between CLGI
+		 * and STGI.  Note, STGI may #UD if SVM is disabled from NMI
+		 * context between reading EFER and executing STGI.  In that
+		 * case, GIF must already be set, otherwise the NMI would have
+		 * been blocked, so just eat the fault.
+		 */
+		asm_volatile_goto("1: stgi\n\t"
+				  _ASM_EXTABLE(1b, %l[fault])
+				  ::: "memory" : fault);
+fault:
+		wrmsrl(MSR_EFER, efer & ~EFER_SVME);
+	}
 }
 
 /** Makes sure SVM is disabled, if it is supported on the CPU
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/vsyscall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/vsyscall.h
@@ -4,6 +4,7 @@
 
 #include <linux/seqlock.h>
 #include <uapi/asm/vsyscall.h>
+#include <asm/page_types.h>
 
 #ifdef CONFIG_X86_VSYSCALL_EMULATION
 extern void map_vsyscall(void);
@@ -24,4 +25,13 @@
 }
 #endif
 
+/*
+ * The (legacy) vsyscall page is the long page in the kernel portion
+ * of the address space that has user-accessible permissions.
+ */
+static inline bool is_vsyscall_vaddr(unsigned long vaddr)
+{
+	return unlikely((vaddr & PAGE_MASK) == VSYSCALL_ADDR);
+}
+
 #endif /* _ASM_X86_VSYSCALL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/xen/hypercall.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/xen/hypercall.h
@@ -39,9 +39,11 @@
 #include <linux/string.h>
 #include <linux/types.h>
 #include <linux/pgtable.h>
+#include <linux/instrumentation.h>
 
 #include <trace/events/xen.h>
 
+#include <asm/alternative.h>
 #include <asm/page.h>
 #include <asm/smap.h>
 #include <asm/nospec-branch.h>
@@ -86,11 +88,20 @@
  * there aren't more than 5 arguments...)
  */
 
-extern struct { char _entry[32]; } hypercall_page[];
+void xen_hypercall_func(void);
+DECLARE_STATIC_CALL(xen_hypercall, xen_hypercall_func);
 
-#define __HYPERCALL		"call hypercall_page+%c[offset]"
-#define __HYPERCALL_ENTRY(x)						\
-	[offset] "i" (__HYPERVISOR_##x * sizeof(hypercall_page[0]))
+#ifdef MODULE
+#define __ADDRESSABLE_xen_hypercall
+#else
+#define __ADDRESSABLE_xen_hypercall __ADDRESSABLE_ASM_STR(__SCK__xen_hypercall)
+#endif
+
+#define __HYPERCALL					\
+	__ADDRESSABLE_xen_hypercall			\
+	"call __SCT__xen_hypercall"
+
+#define __HYPERCALL_ENTRY(x)	"a" (x)
 
 #ifdef CONFIG_X86_32
 #define __HYPERCALL_RETREG	"eax"
@@ -148,7 +159,7 @@
 	__HYPERCALL_0ARG();						\
 	asm volatile (__HYPERCALL					\
 		      : __HYPERCALL_0PARAM				\
-		      : __HYPERCALL_ENTRY(name)				\
+		      : __HYPERCALL_ENTRY(__HYPERVISOR_ ## name)	\
 		      : __HYPERCALL_CLOBBER0);				\
 	(type)__res;							\
 })
@@ -159,7 +170,7 @@
 	__HYPERCALL_1ARG(a1);						\
 	asm volatile (__HYPERCALL					\
 		      : __HYPERCALL_1PARAM				\
-		      : __HYPERCALL_ENTRY(name)				\
+		      : __HYPERCALL_ENTRY(__HYPERVISOR_ ## name)	\
 		      : __HYPERCALL_CLOBBER1);				\
 	(type)__res;							\
 })
@@ -170,7 +181,7 @@
 	__HYPERCALL_2ARG(a1, a2);					\
 	asm volatile (__HYPERCALL					\
 		      : __HYPERCALL_2PARAM				\
-		      : __HYPERCALL_ENTRY(name)				\
+		      : __HYPERCALL_ENTRY(__HYPERVISOR_ ## name)	\
 		      : __HYPERCALL_CLOBBER2);				\
 	(type)__res;							\
 })
@@ -181,7 +192,7 @@
 	__HYPERCALL_3ARG(a1, a2, a3);					\
 	asm volatile (__HYPERCALL					\
 		      : __HYPERCALL_3PARAM				\
-		      : __HYPERCALL_ENTRY(name)				\
+		      : __HYPERCALL_ENTRY(__HYPERVISOR_ ## name)	\
 		      : __HYPERCALL_CLOBBER3);				\
 	(type)__res;							\
 })
@@ -192,7 +203,7 @@
 	__HYPERCALL_4ARG(a1, a2, a3, a4);				\
 	asm volatile (__HYPERCALL					\
 		      : __HYPERCALL_4PARAM				\
-		      : __HYPERCALL_ENTRY(name)				\
+		      : __HYPERCALL_ENTRY(__HYPERVISOR_ ## name)	\
 		      : __HYPERCALL_CLOBBER4);				\
 	(type)__res;							\
 })
@@ -206,12 +217,9 @@
 	__HYPERCALL_DECLS;
 	__HYPERCALL_5ARG(a1, a2, a3, a4, a5);
 
-	if (call >= PAGE_SIZE / sizeof(hypercall_page[0]))
-		return -EINVAL;
-
-	asm volatile(CALL_NOSPEC
+	asm volatile(__HYPERCALL
 		     : __HYPERCALL_5PARAM
-		     : [thunk_target] "a" (&hypercall_page[call])
+		     : __HYPERCALL_ENTRY(call)
 		     : __HYPERCALL_CLOBBER5);
 
 	return (long)__res;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/asm/xen/hypervisor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/asm/xen/hypervisor.h
@@ -62,4 +62,9 @@
 void xen_arch_unregister_cpu(int num);
 #endif
 
+#ifdef CONFIG_PVH
+void __init xen_pvh_init(struct boot_params *boot_params);
+void __init mem_map_via_hcall(struct boot_params *boot_params_p);
+#endif
+
 #endif /* _ASM_X86_XEN_HYPERVISOR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/include/uapi/asm/prctl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/include/uapi/asm/prctl.h
@@ -10,6 +10,10 @@
 #define ARCH_GET_CPUID		0x1011
 #define ARCH_SET_CPUID		0x1012
 
+#define ARCH_GET_XCOMP_SUPP	0x1021
+#define ARCH_GET_XCOMP_PERM	0x1022
+#define ARCH_REQ_XCOMP_PERM	0x1023
+
 #define ARCH_MAP_VDSO_X32	0x2001
 #define ARCH_MAP_VDSO_32	0x2002
 #define ARCH_MAP_VDSO_64	0x2003
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/Makefile
@@ -21,6 +21,7 @@
 CFLAGS_REMOVE_early_printk.o = -pg
 CFLAGS_REMOVE_head64.o = -pg
 CFLAGS_REMOVE_sev.o = -pg
+CFLAGS_REMOVE_cc_platform.o = -pg
 endif
 
 KASAN_SANITIZE_head$(BITS).o				:= n
@@ -29,6 +30,7 @@
 KASAN_SANITIZE_stacktrace.o				:= n
 KASAN_SANITIZE_paravirt.o				:= n
 KASAN_SANITIZE_sev.o					:= n
+KASAN_SANITIZE_cc_platform.o				:= n
 
 # With some compiler versions the generated code results in boot hangs, caused
 # by several compilation units. To be safe, disable all instrumentation.
@@ -47,6 +49,7 @@
 KCOV_INSTRUMENT		:= n
 
 CFLAGS_head$(BITS).o	+= -fno-stack-protector
+CFLAGS_cc_platform.o	+= -fno-stack-protector
 
 CFLAGS_irq.o := -I $(srctree)/$(src)/../include/asm/trace
 
@@ -147,6 +150,9 @@
 obj-$(CONFIG_UNWINDER_GUESS)		+= unwind_guess.o
 
 obj-$(CONFIG_AMD_MEM_ENCRYPT)		+= sev.o
+
+obj-$(CONFIG_ARCH_HAS_CC_PLATFORM)	+= cc_platform.o
+
 ###
 # 64 bit specific files
 ifeq ($(CONFIG_X86_64),y)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/acpi/boot.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/acpi/boot.c
@@ -139,6 +139,9 @@
 		pr_debug("Local APIC address 0x%08x\n", madt->address);
 	}
 
+	if (madt->flags & ACPI_MADT_PCAT_COMPAT)
+		legacy_pic_pcat_compat();
+
 	default_acpi_madt_oem_check(madt->header.oem_id,
 				    madt->header.oem_table_id);
 
@@ -1319,6 +1322,17 @@
 	return 0;
 }
 
+static int __init disable_acpi_xsdt(const struct dmi_system_id *d)
+{
+	if (!acpi_force) {
+		pr_notice("%s detected: force use of acpi=rsdt\n", d->ident);
+		acpi_gbl_do_not_use_xsdt = TRUE;
+	} else {
+		pr_notice("Warning: DMI blacklist says broken, but acpi XSDT forced\n");
+	}
+	return 0;
+}
+
 static int __init dmi_disable_acpi(const struct dmi_system_id *d)
 {
 	if (!acpi_force) {
@@ -1442,6 +1456,19 @@
 		     DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate 360"),
 		     },
 	 },
+	/*
+	 * Boxes that need ACPI XSDT use disabled due to corrupted tables
+	 */
+	{
+	 .callback = disable_acpi_xsdt,
+	 .ident = "Advantech DAC-BJ01",
+	 .matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "NEC"),
+		     DMI_MATCH(DMI_PRODUCT_NAME, "Bearlake CRB Board"),
+		     DMI_MATCH(DMI_BIOS_VERSION, "V1.12"),
+		     DMI_MATCH(DMI_BIOS_DATE, "02/01/2011"),
+		     },
+	 },
 	{}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/acpi/cstate.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/acpi/cstate.c
@@ -79,6 +79,36 @@
 		 */
 		flags->bm_control = 0;
 	}
+	if (c->x86_vendor == X86_VENDOR_AMD && c->x86 >= 0x17) {
+		/*
+		 * For all AMD Zen or newer CPUs that support C3, caches
+		 * should not be flushed by software while entering C3
+		 * type state. Set bm->check to 1 so that kernel doesn't
+		 * need to execute cache flush operation.
+		 */
+		flags->bm_check = 1;
+		/*
+		 * In current AMD C state implementation ARB_DIS is no longer
+		 * used. So set bm_control to zero to indicate ARB_DIS is not
+		 * required while entering C3 type state.
+		 */
+		flags->bm_control = 0;
+	}
+	if (c->x86_vendor == X86_VENDOR_AMD && c->x86 >= 0x17) {
+		/*
+		 * For all AMD Zen or newer CPUs that support C3, caches
+		 * should not be flushed by software while entering C3
+		 * type state. Set bm->check to 1 so that kernel doesn't
+		 * need to execute cache flush operation.
+		 */
+		flags->bm_check = 1;
+		/*
+		 * In current AMD C state implementation ARB_DIS is no longer
+		 * used. So set bm_control to zero to indicate ARB_DIS is not
+		 * required while entering C3 type state.
+		 */
+		flags->bm_control = 0;
+	}
 }
 EXPORT_SYMBOL(acpi_processor_power_init_bm_check);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/acpi/wakeup_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/acpi/wakeup_32.S
@@ -3,6 +3,7 @@
 #include <linux/linkage.h>
 #include <asm/segment.h>
 #include <asm/page_types.h>
+#include <asm/nospec-branch.h>
 
 # Copyright 2003, 2008 Pavel Machek <pavel@suse.cz
 
@@ -37,6 +38,7 @@
 
 	# jump to place where we left off
 	movl	saved_eip, %eax
+	ANNOTATE_RETPOLINE_SAFE
 	jmp	*%eax
 SYM_CODE_END(wakeup_pmode_return)
 
@@ -60,7 +62,7 @@
 	popl	saved_context_eflags
 
 	movl	$ret_point, saved_eip
-	ret
+	RET
 
 
 restore_registers:
@@ -70,7 +72,7 @@
 	movl	saved_context_edi, %edi
 	pushl	saved_context_eflags
 	popfl
-	ret
+	RET
 
 SYM_CODE_START(do_suspend_lowlevel)
 	call	save_processor_state
@@ -86,7 +88,7 @@
 ret_point:
 	call	restore_registers
 	call	restore_processor_state
-	ret
+	RET
 SYM_CODE_END(do_suspend_lowlevel)
 
 .data
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/alternative.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/alternative.c
@@ -29,6 +29,7 @@
 #include <asm/io.h>
 #include <asm/fixmap.h>
 #include <asm/paravirt.h>
+#include <asm/asm-prototypes.h>
 
 int __read_mostly alternatives_patched;
 
@@ -113,6 +114,8 @@
 	}
 }
 
+extern s32 __retpoline_sites[], __retpoline_sites_end[];
+extern s32 __return_sites[], __return_sites_end[];
 extern struct alt_instr __alt_instructions[], __alt_instructions_end[];
 extern s32 __smp_locks[], __smp_locks_end[];
 void text_poke_early(void *addr, const void *opcode, size_t len);
@@ -221,7 +224,7 @@
  * "noinline" to cause control flow change and thus invalidate I$ and
  * cause refetch after modification.
  */
-static void __init_or_module noinline optimize_nops(struct alt_instr *a, u8 *instr)
+static void __init_or_module noinline optimize_nops(u8 *instr, size_t len)
 {
 	struct insn insn;
 	int i = 0;
@@ -239,11 +242,11 @@
 		 * optimized.
 		 */
 		if (insn.length == 1 && insn.opcode.bytes[0] == 0x90)
-			i += optimize_nops_range(instr, a->instrlen, i);
+			i += optimize_nops_range(instr, len, i);
 		else
 			i += insn.length;
 
-		if (i >= a->instrlen)
+		if (i >= len)
 			return;
 	}
 }
@@ -266,6 +269,17 @@
 	u8 insn_buff[MAX_PATCH_LEN];
 
 	DPRINTK("alt table %px, -> %px", start, end);
+
+	/*
+	 * In the case CONFIG_X86_5LEVEL=y, KASAN_SHADOW_START is defined using
+	 * cpu_feature_enabled(X86_FEATURE_LA57) and is therefore patched here.
+	 * During the process, KASAN becomes confused seeing partial LA57
+	 * conversion and triggers a false-positive out-of-bound report.
+	 *
+	 * Disable KASAN until the patching is complete.
+	 */
+	kasan_disable_current();
+
 	/*
 	 * The scan order should be from start to end. A later scanned
 	 * alternative code can overwrite previously scanned alternative code.
@@ -331,10 +345,267 @@
 		text_poke_early(instr, insn_buff, insn_buff_sz);
 
 next:
-		optimize_nops(a, instr);
+		optimize_nops(instr, a->instrlen);
+	}
+
+	kasan_enable_current();
+}
+
+static inline bool is_jcc32(struct insn *insn)
+{
+	/* Jcc.d32 second opcode byte is in the range: 0x80-0x8f */
+	return insn->opcode.bytes[0] == 0x0f && (insn->opcode.bytes[1] & 0xf0) == 0x80;
+}
+
+#if defined(CONFIG_RETPOLINE) && defined(CONFIG_STACK_VALIDATION)
+
+/*
+ * CALL/JMP *%\reg
+ */
+static int emit_indirect(int op, int reg, u8 *bytes)
+{
+	int i = 0;
+	u8 modrm;
+
+	switch (op) {
+	case CALL_INSN_OPCODE:
+		modrm = 0x10; /* Reg = 2; CALL r/m */
+		break;
+
+	case JMP32_INSN_OPCODE:
+		modrm = 0x20; /* Reg = 4; JMP r/m */
+		break;
+
+	default:
+		WARN_ON_ONCE(1);
+		return -1;
 	}
+
+	if (reg >= 8) {
+		bytes[i++] = 0x41; /* REX.B prefix */
+		reg -= 8;
+	}
+
+	modrm |= 0xc0; /* Mod = 3 */
+	modrm += reg;
+
+	bytes[i++] = 0xff; /* opcode */
+	bytes[i++] = modrm;
+
+	return i;
 }
 
+/*
+ * Rewrite the compiler generated retpoline thunk calls.
+ *
+ * For spectre_v2=off (!X86_FEATURE_RETPOLINE), rewrite them into immediate
+ * indirect instructions, avoiding the extra indirection.
+ *
+ * For example, convert:
+ *
+ *   CALL __x86_indirect_thunk_\reg
+ *
+ * into:
+ *
+ *   CALL *%\reg
+ *
+ * It also tries to inline spectre_v2=retpoline,amd when size permits.
+ */
+static int patch_retpoline(void *addr, struct insn *insn, u8 *bytes)
+{
+	retpoline_thunk_t *target;
+	int reg, ret, i = 0;
+	u8 op, cc;
+
+	target = addr + insn->length + insn->immediate.value;
+	reg = target - __x86_indirect_thunk_array;
+
+	if (WARN_ON_ONCE(reg & ~0xf))
+		return -1;
+
+	/* If anyone ever does: CALL/JMP *%rsp, we're in deep trouble. */
+	BUG_ON(reg == 4);
+
+	if (cpu_feature_enabled(X86_FEATURE_RETPOLINE) &&
+	    !cpu_feature_enabled(X86_FEATURE_RETPOLINE_LFENCE))
+		return -1;
+
+	op = insn->opcode.bytes[0];
+
+	/*
+	 * Convert:
+	 *
+	 *   Jcc.d32 __x86_indirect_thunk_\reg
+	 *
+	 * into:
+	 *
+	 *   Jncc.d8 1f
+	 *   [ LFENCE ]
+	 *   JMP *%\reg
+	 *   [ NOP ]
+	 * 1:
+	 */
+	/* Jcc.d32 second opcode byte is in the range: 0x80-0x8f */
+	if (op == 0x0f && (insn->opcode.bytes[1] & 0xf0) == 0x80) {
+		cc = insn->opcode.bytes[1] & 0xf;
+		cc ^= 1; /* invert condition */
+
+		bytes[i++] = 0x70 + cc;        /* Jcc.d8 */
+		bytes[i++] = insn->length - 2; /* sizeof(Jcc.d8) == 2 */
+
+		/* Continue as if: JMP.d32 __x86_indirect_thunk_\reg */
+		op = JMP32_INSN_OPCODE;
+	}
+
+	/*
+	 * For RETPOLINE_AMD: prepend the indirect CALL/JMP with an LFENCE.
+	 */
+	if (cpu_feature_enabled(X86_FEATURE_RETPOLINE_LFENCE)) {
+		bytes[i++] = 0x0f;
+		bytes[i++] = 0xae;
+		bytes[i++] = 0xe8; /* LFENCE */
+	}
+
+	ret = emit_indirect(op, reg, bytes + i);
+	if (ret < 0)
+		return ret;
+	i += ret;
+
+	for (; i < insn->length;)
+		bytes[i++] = BYTES_NOP1;
+
+	return i;
+}
+
+/*
+ * Generated by 'objtool --retpoline'.
+ */
+void __init_or_module noinline apply_retpolines(s32 *start, s32 *end)
+{
+	s32 *s;
+
+	for (s = start; s < end; s++) {
+		void *addr = (void *)s + *s;
+		struct insn insn;
+		int len, ret;
+		u8 bytes[16];
+		u8 op1, op2;
+
+		ret = insn_decode_kernel(&insn, addr);
+		if (WARN_ON_ONCE(ret < 0))
+			continue;
+
+		op1 = insn.opcode.bytes[0];
+		op2 = insn.opcode.bytes[1];
+
+		switch (op1) {
+		case CALL_INSN_OPCODE:
+		case JMP32_INSN_OPCODE:
+			break;
+
+		case 0x0f: /* escape */
+			if (op2 >= 0x80 && op2 <= 0x8f)
+				break;
+			fallthrough;
+		default:
+			WARN_ON_ONCE(1);
+			continue;
+		}
+
+		DPRINTK("retpoline at: %pS (%px) len: %d to: %pS",
+			addr, addr, insn.length,
+			addr + insn.length + insn.immediate.value);
+
+		len = patch_retpoline(addr, &insn, bytes);
+		if (len == insn.length) {
+			optimize_nops(bytes, len);
+			DUMP_BYTES(((u8*)addr),  len, "%px: orig: ", addr);
+			DUMP_BYTES(((u8*)bytes), len, "%px: repl: ", addr);
+			text_poke_early(addr, bytes, len);
+		}
+	}
+}
+
+#ifdef CONFIG_RETHUNK
+
+/*
+ * Rewrite the compiler generated return thunk tail-calls.
+ *
+ * For example, convert:
+ *
+ *   JMP __x86_return_thunk
+ *
+ * into:
+ *
+ *   RET
+ */
+static int patch_return(void *addr, struct insn *insn, u8 *bytes)
+{
+	int i = 0;
+
+	if (cpu_feature_enabled(X86_FEATURE_RETHUNK)) {
+		if (x86_return_thunk == __x86_return_thunk)
+			return -1;
+
+		i = JMP32_INSN_SIZE;
+		__text_gen_insn(bytes, JMP32_INSN_OPCODE, addr, x86_return_thunk, i);
+	} else {
+		bytes[i++] = RET_INSN_OPCODE;
+	}
+
+	for (; i < insn->length;)
+		bytes[i++] = INT3_INSN_OPCODE;
+	return i;
+}
+
+void __init_or_module noinline apply_returns(s32 *start, s32 *end)
+{
+	s32 *s;
+
+	for (s = start; s < end; s++) {
+		void *dest = NULL, *addr = (void *)s + *s;
+		struct insn insn;
+		int len, ret;
+		u8 bytes[16];
+		u8 op;
+
+		ret = insn_decode_kernel(&insn, addr);
+		if (WARN_ON_ONCE(ret < 0))
+			continue;
+
+		op = insn.opcode.bytes[0];
+		if (op == JMP32_INSN_OPCODE)
+			dest = addr + insn.length + insn.immediate.value;
+
+		if (__static_call_fixup(addr, op, dest) ||
+		    WARN_ONCE(dest != &__x86_return_thunk,
+			      "missing return thunk: %pS-%pS: %*ph",
+			      addr, dest, 5, addr))
+			continue;
+
+		DPRINTK("return thunk at: %pS (%px) len: %d to: %pS",
+			addr, addr, insn.length,
+			addr + insn.length + insn.immediate.value);
+
+		len = patch_return(addr, &insn, bytes);
+		if (len == insn.length) {
+			DUMP_BYTES(((u8*)addr),  len, "%px: orig: ", addr);
+			DUMP_BYTES(((u8*)bytes), len, "%px: repl: ", addr);
+			text_poke_early(addr, bytes, len);
+		}
+	}
+}
+#else
+void __init_or_module noinline apply_returns(s32 *start, s32 *end) { }
+#endif /* CONFIG_RETHUNK */
+
+#else /* !RETPOLINES || !CONFIG_STACK_VALIDATION */
+
+void __init_or_module noinline apply_retpolines(s32 *start, s32 *end) { }
+void __init_or_module noinline apply_returns(s32 *start, s32 *end) { }
+
+#endif /* CONFIG_RETPOLINE && CONFIG_STACK_VALIDATION */
+
 #ifdef CONFIG_SMP
 static void alternatives_smp_lock(const s32 *start, const s32 *end,
 				  u8 *text, u8 *text_end)
@@ -537,7 +808,7 @@
 "	.type		int3_magic, @function\n"
 "int3_magic:\n"
 "	movl	$1, (%" _ASM_ARG1 ")\n"
-"	ret\n"
+	ASM_RET
 "	.size		int3_magic, .-int3_magic\n"
 "	.popsection\n"
 );
@@ -643,6 +914,13 @@
 	apply_paravirt(__parainstructions, __parainstructions_end);
 
 	/*
+	 * Rewrite the retpolines, must be done before alternatives since
+	 * those can rewrite the retpoline thunks.
+	 */
+	apply_retpolines(__retpoline_sites, __retpoline_sites_end);
+	apply_returns(__return_sites, __return_sites_end);
+
+	/*
 	 * Then patch alternatives, such that those paravirt calls that are in
 	 * alternatives can be overwritten by their immediate fragments.
 	 */
@@ -696,8 +974,8 @@
 	} else {
 		local_irq_save(flags);
 		memcpy(addr, opcode, len);
-		local_irq_restore(flags);
 		sync_core();
+		local_irq_restore(flags);
 
 		/*
 		 * Could also do a CLFLUSH here to speed up CPU recovery; but
@@ -929,11 +1207,19 @@
 	on_each_cpu(do_sync_core, NULL, 1);
 }
 
+/*
+ * NOTE: crazy scheme to allow patching Jcc.d32 but not increase the size of
+ * this thing. When len == 6 everything is prefixed with 0x0f and we map
+ * opcode to Jcc.d8, using len to distinguish.
+ */
 struct text_poke_loc {
-	s32 rel_addr; /* addr := _stext + rel_addr */
-	s32 rel32;
+	/* addr := _stext + rel_addr */
+	s32 rel_addr;
+	s32 disp;
+	u8 len;
 	u8 opcode;
 	const u8 text[POKE_MAX_OPCODE_SIZE];
+	/* see text_poke_bp_batch() */
 	u8 old;
 };
 
@@ -943,21 +1229,23 @@
 	atomic_t refs;
 };
 
-static struct bp_patching_desc *bp_desc;
+static struct bp_patching_desc bp_desc;
 
 static __always_inline
-struct bp_patching_desc *try_get_desc(struct bp_patching_desc **descp)
+struct bp_patching_desc *try_get_desc(void)
 {
-	struct bp_patching_desc *desc = __READ_ONCE(*descp); /* rcu_dereference */
+	struct bp_patching_desc *desc = &bp_desc;
 
-	if (!desc || !arch_atomic_inc_not_zero(&desc->refs))
+	if (!arch_atomic_inc_not_zero(&desc->refs))
 		return NULL;
 
 	return desc;
 }
 
-static __always_inline void put_desc(struct bp_patching_desc *desc)
+static __always_inline void put_desc(void)
 {
+	struct bp_patching_desc *desc = &bp_desc;
+
 	smp_mb__before_atomic();
 	arch_atomic_dec(&desc->refs);
 }
@@ -982,7 +1270,7 @@
 {
 	struct bp_patching_desc *desc;
 	struct text_poke_loc *tp;
-	int len, ret = 0;
+	int ret = 0;
 	void *ip;
 
 	if (user_mode(regs))
@@ -990,15 +1278,15 @@
 
 	/*
 	 * Having observed our INT3 instruction, we now must observe
-	 * bp_desc:
+	 * bp_desc with non-zero refcount:
 	 *
-	 *	bp_desc = desc			INT3
+	 *	bp_desc.refs = 1		INT3
 	 *	WMB				RMB
-	 *	write INT3			if (desc)
+	 *	write INT3			if (bp_desc.refs != 0)
 	 */
 	smp_rmb();
 
-	desc = try_get_desc(&bp_desc);
+	desc = try_get_desc();
 	if (!desc)
 		return 0;
 
@@ -1022,8 +1310,7 @@
 			goto out_put;
 	}
 
-	len = text_opcode_size(tp->opcode);
-	ip += len;
+	ip += tp->len;
 
 	switch (tp->opcode) {
 	case INT3_INSN_OPCODE:
@@ -1038,12 +1325,16 @@
 		break;
 
 	case CALL_INSN_OPCODE:
-		int3_emulate_call(regs, (long)ip + tp->rel32);
+		int3_emulate_call(regs, (long)ip + tp->disp);
 		break;
 
 	case JMP32_INSN_OPCODE:
 	case JMP8_INSN_OPCODE:
-		int3_emulate_jmp(regs, (long)ip + tp->rel32);
+		int3_emulate_jmp(regs, (long)ip + tp->disp);
+		break;
+
+	case 0x70 ... 0x7f: /* Jcc */
+		int3_emulate_jcc(regs, tp->opcode & 0xf, (long)ip, tp->disp);
 		break;
 
 	default:
@@ -1053,7 +1344,7 @@
 	ret = 1;
 
 out_put:
-	put_desc(desc);
+	put_desc();
 	return ret;
 }
 
@@ -1084,18 +1375,20 @@
  */
 static void text_poke_bp_batch(struct text_poke_loc *tp, unsigned int nr_entries)
 {
-	struct bp_patching_desc desc = {
-		.vec = tp,
-		.nr_entries = nr_entries,
-		.refs = ATOMIC_INIT(1),
-	};
 	unsigned char int3 = INT3_INSN_OPCODE;
 	unsigned int i;
 	int do_sync;
 
 	lockdep_assert_held(&text_mutex);
 
-	smp_store_release(&bp_desc, &desc); /* rcu_assign_pointer */
+	bp_desc.vec = tp;
+	bp_desc.nr_entries = nr_entries;
+
+	/*
+	 * Corresponds to the implicit memory barrier in try_get_desc() to
+	 * ensure reading a non-zero refcount provides up to date bp_desc data.
+	 */
+	atomic_set_release(&bp_desc.refs, 1);
 
 	/*
 	 * Corresponding read barrier in int3 notifier for making sure the
@@ -1117,16 +1410,26 @@
 	 * Second step: update all but the first byte of the patched range.
 	 */
 	for (do_sync = 0, i = 0; i < nr_entries; i++) {
-		u8 old[POKE_MAX_OPCODE_SIZE] = { tp[i].old, };
-		int len = text_opcode_size(tp[i].opcode);
+		u8 old[POKE_MAX_OPCODE_SIZE+1] = { tp[i].old, };
+		u8 _new[POKE_MAX_OPCODE_SIZE+1];
+		const u8 *new = tp[i].text;
+		int len = tp[i].len;
 
 		if (len - INT3_INSN_SIZE > 0) {
 			memcpy(old + INT3_INSN_SIZE,
 			       text_poke_addr(&tp[i]) + INT3_INSN_SIZE,
 			       len - INT3_INSN_SIZE);
+
+			if (len == 6) {
+				_new[0] = 0x0f;
+				memcpy(_new + 1, new, 5);
+				new = _new;
+			}
+
 			text_poke(text_poke_addr(&tp[i]) + INT3_INSN_SIZE,
-				  (const char *)tp[i].text + INT3_INSN_SIZE,
+				  new + INT3_INSN_SIZE,
 				  len - INT3_INSN_SIZE);
+
 			do_sync++;
 		}
 
@@ -1154,8 +1457,7 @@
 		 * The old instruction is recorded so that the event can be
 		 * processed forwards or backwards.
 		 */
-		perf_event_text_poke(text_poke_addr(&tp[i]), old, len,
-				     tp[i].text, len);
+		perf_event_text_poke(text_poke_addr(&tp[i]), old, len, new, len);
 	}
 
 	if (do_sync) {
@@ -1172,10 +1474,15 @@
 	 * replacing opcode.
 	 */
 	for (do_sync = 0, i = 0; i < nr_entries; i++) {
-		if (tp[i].text[0] == INT3_INSN_OPCODE)
+		u8 byte = tp[i].text[0];
+
+		if (tp[i].len == 6)
+			byte = 0x0f;
+
+		if (byte == INT3_INSN_OPCODE)
 			continue;
 
-		text_poke(text_poke_addr(&tp[i]), tp[i].text, INT3_INSN_SIZE);
+		text_poke(text_poke_addr(&tp[i]), &byte, INT3_INSN_SIZE);
 		do_sync++;
 	}
 
@@ -1183,32 +1490,54 @@
 		text_poke_sync();
 
 	/*
-	 * Remove and synchronize_rcu(), except we have a very primitive
-	 * refcount based completion.
+	 * Remove and wait for refs to be zero.
 	 */
-	WRITE_ONCE(bp_desc, NULL); /* RCU_INIT_POINTER */
-	if (!atomic_dec_and_test(&desc.refs))
-		atomic_cond_read_acquire(&desc.refs, !VAL);
+	if (!atomic_dec_and_test(&bp_desc.refs))
+		atomic_cond_read_acquire(&bp_desc.refs, !VAL);
 }
 
 static void text_poke_loc_init(struct text_poke_loc *tp, void *addr,
 			       const void *opcode, size_t len, const void *emulate)
 {
 	struct insn insn;
-	int ret;
+	int ret, i = 0;
 
-	memcpy((void *)tp->text, opcode, len);
+	if (len == 6)
+		i = 1;
+	memcpy((void *)tp->text, opcode+i, len-i);
 	if (!emulate)
 		emulate = opcode;
 
 	ret = insn_decode_kernel(&insn, emulate);
-
 	BUG_ON(ret < 0);
-	BUG_ON(len != insn.length);
 
 	tp->rel_addr = addr - (void *)_stext;
+	tp->len = len;
 	tp->opcode = insn.opcode.bytes[0];
 
+	if (is_jcc32(&insn)) {
+		/*
+		 * Map Jcc.d32 onto Jcc.d8 and use len to distinguish.
+		 */
+		tp->opcode = insn.opcode.bytes[1] - 0x10;
+	}
+
+	switch (tp->opcode) {
+	case RET_INSN_OPCODE:
+	case JMP32_INSN_OPCODE:
+	case JMP8_INSN_OPCODE:
+		/*
+		 * Control flow instructions without implied execution of the
+		 * next instruction can be padded with INT3.
+		 */
+		for (i = insn.length; i < len; i++)
+			BUG_ON(tp->text[i] != INT3_INSN_OPCODE);
+		break;
+
+	default:
+		BUG_ON(len != insn.length);
+	};
+
 	switch (tp->opcode) {
 	case INT3_INSN_OPCODE:
 	case RET_INSN_OPCODE:
@@ -1217,7 +1546,8 @@
 	case CALL_INSN_OPCODE:
 	case JMP32_INSN_OPCODE:
 	case JMP8_INSN_OPCODE:
-		tp->rel32 = insn.immediate.value;
+	case 0x70 ... 0x7f: /* Jcc */
+		tp->disp = insn.immediate.value;
 		break;
 
 	default: /* assume NOP */
@@ -1225,13 +1555,13 @@
 		case 2: /* NOP2 -- emulate as JMP8+0 */
 			BUG_ON(memcmp(emulate, x86_nops[len], len));
 			tp->opcode = JMP8_INSN_OPCODE;
-			tp->rel32 = 0;
+			tp->disp = 0;
 			break;
 
 		case 5: /* NOP5 -- emulate as JMP32+0 */
 			BUG_ON(memcmp(emulate, x86_nops[len], len));
 			tp->opcode = JMP32_INSN_OPCODE;
-			tp->rel32 = 0;
+			tp->disp = 0;
 			break;
 
 		default: /* unknown instruction */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/amd_nb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/amd_nb.c
@@ -19,12 +19,14 @@
 #define PCI_DEVICE_ID_AMD_17H_M10H_ROOT	0x15d0
 #define PCI_DEVICE_ID_AMD_17H_M30H_ROOT	0x1480
 #define PCI_DEVICE_ID_AMD_17H_M60H_ROOT	0x1630
+#define PCI_DEVICE_ID_AMD_19H_M10H_ROOT	0x14a4
 #define PCI_DEVICE_ID_AMD_17H_DF_F4	0x1464
 #define PCI_DEVICE_ID_AMD_17H_M10H_DF_F4 0x15ec
 #define PCI_DEVICE_ID_AMD_17H_M30H_DF_F4 0x1494
 #define PCI_DEVICE_ID_AMD_17H_M60H_DF_F4 0x144c
 #define PCI_DEVICE_ID_AMD_17H_M70H_DF_F4 0x1444
 #define PCI_DEVICE_ID_AMD_19H_DF_F4	0x1654
+#define PCI_DEVICE_ID_AMD_19H_M10H_DF_F4 0x14b1
 #define PCI_DEVICE_ID_AMD_19H_M40H_ROOT	0x14b5
 #define PCI_DEVICE_ID_AMD_19H_M40H_DF_F4 0x167d
 #define PCI_DEVICE_ID_AMD_19H_M50H_DF_F4 0x166e
@@ -39,6 +41,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M10H_ROOT) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M30H_ROOT) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M60H_ROOT) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M10H_ROOT) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M40H_ROOT) },
 	{}
 };
@@ -61,6 +64,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CNB17H_F3) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M70H_DF_F3) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_DF_F3) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M10H_DF_F3) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M40H_DF_F3) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M50H_DF_F3) },
 	{}
@@ -78,6 +82,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M60H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M70H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_DF_F4) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M10H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M40H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_19H_M50H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CNB17H_F4) },
@@ -172,7 +177,14 @@
 
 int amd_smn_read(u16 node, u32 address, u32 *value)
 {
-	return __amd_smn_rw(node, address, value, false);
+	int err = __amd_smn_rw(node, address, value, false);
+
+	if (PCI_POSSIBLE_ERROR(*value)) {
+		err = -ENODEV;
+		*value = 0;
+	}
+
+	return err;
 }
 EXPORT_SYMBOL_GPL(amd_smn_read);
 
@@ -537,6 +549,10 @@
 
 static __init int init_amd_nbs(void)
 {
+	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD &&
+	    boot_cpu_data.x86_vendor != X86_VENDOR_HYGON)
+		return 0;
+
 	amd_cache_northbridges();
 	amd_cache_gart();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/aperture_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/aperture_64.c
@@ -125,32 +125,6 @@
 }
 
 
-/* Find a PCI capability */
-static u32 __init find_cap(int bus, int slot, int func, int cap)
-{
-	int bytes;
-	u8 pos;
-
-	if (!(read_pci_config_16(bus, slot, func, PCI_STATUS) &
-						PCI_STATUS_CAP_LIST))
-		return 0;
-
-	pos = read_pci_config_byte(bus, slot, func, PCI_CAPABILITY_LIST);
-	for (bytes = 0; bytes < 48 && pos >= 0x40; bytes++) {
-		u8 id;
-
-		pos &= ~3;
-		id = read_pci_config_byte(bus, slot, func, pos+PCI_CAP_LIST_ID);
-		if (id == 0xff)
-			break;
-		if (id == cap)
-			return pos;
-		pos = read_pci_config_byte(bus, slot, func,
-						pos+PCI_CAP_LIST_NEXT);
-	}
-	return 0;
-}
-
 /* Read a standard AGPv3 bridge header */
 static u32 __init read_agp(int bus, int slot, int func, int cap, u32 *order)
 {
@@ -239,8 +213,8 @@
 				case PCI_CLASS_BRIDGE_HOST:
 				case PCI_CLASS_BRIDGE_OTHER: /* needed? */
 					/* AGP bridge? */
-					cap = find_cap(bus, slot, func,
-							PCI_CAP_ID_AGP);
+					cap = pci_early_find_cap(bus, slot,
+						 func, PCI_CAP_ID_AGP);
 					if (!cap)
 						break;
 					*valid_agp = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/apic/apic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/apic/apic.c
@@ -170,7 +170,7 @@
 {
 	apic_calibrate_pmtmr = 1;
 	notsc_setup(NULL);
-	return 0;
+	return 1;
 }
 __setup("apicpmtimer", setup_apicpmtimer);
 #endif
@@ -412,10 +412,9 @@
 		if (vector && !eilvt_entry_is_changeable(vector, new))
 			/* may not change if vectors are different */
 			return rsvd;
-		rsvd = atomic_cmpxchg(&eilvt_offsets[offset], rsvd, new);
-	} while (rsvd != new);
+	} while (!atomic_try_cmpxchg(&eilvt_offsets[offset], &rsvd, new));
 
-	rsvd &= ~APIC_EILVT_MASKED;
+	rsvd = new & ~APIC_EILVT_MASKED;
 	if (rsvd && rsvd != vector)
 		pr_info("LVT offset %d assigned for vector 0x%02x\n",
 			offset, rsvd);
@@ -494,7 +493,19 @@
 	v = apic_read(APIC_LVTT);
 	v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
 	apic_write(APIC_LVTT, v);
-	apic_write(APIC_TMICT, 0);
+
+	/*
+	 * Setting APIC_LVT_MASKED (above) should be enough to tell
+	 * the hardware that this timer will never fire. But AMD
+	 * erratum 411 and some Intel CPU behavior circa 2024 say
+	 * otherwise.  Time for belt and suspenders programming: mask
+	 * the timer _and_ zero the counter registers:
+	 */
+	if (v & APIC_LVT_TIMER_TSCDEADLINE)
+		wrmsrl(MSR_IA32_TSC_DEADLINE, 0);
+	else
+		apic_write(APIC_TMICT, 0);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/apic/io_apic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/apic/io_apic.c
@@ -350,27 +350,26 @@
  * shared ISA-space IRQs, so we have to support them. We are super
  * fast in the common case, and fast for shared ISA-space IRQs.
  */
-static int __add_pin_to_irq_node(struct mp_chip_data *data,
-				 int node, int apic, int pin)
+static bool add_pin_to_irq_node(struct mp_chip_data *data, int node, int apic, int pin)
 {
 	struct irq_pin_list *entry;
 
-	/* don't allow duplicates */
-	for_each_irq_pin(entry, data->irq_2_pin)
+	/* Don't allow duplicates */
+	for_each_irq_pin(entry, data->irq_2_pin) {
 		if (entry->apic == apic && entry->pin == pin)
-			return 0;
+			return true;
+	}
 
 	entry = kzalloc_node(sizeof(struct irq_pin_list), GFP_ATOMIC, node);
 	if (!entry) {
-		pr_err("can not alloc irq_pin_list (%d,%d,%d)\n",
-		       node, apic, pin);
-		return -ENOMEM;
+		pr_err("Cannot allocate irq_pin_list (%d,%d,%d)\n", node, apic, pin);
+		return false;
 	}
+
 	entry->apic = apic;
 	entry->pin = pin;
 	list_add_tail(&entry->list, &data->irq_2_pin);
-
-	return 0;
+	return true;
 }
 
 static void __remove_pin_from_irq(struct mp_chip_data *data, int apic, int pin)
@@ -385,13 +384,6 @@
 		}
 }
 
-static void add_pin_to_irq_node(struct mp_chip_data *data,
-				int node, int apic, int pin)
-{
-	if (__add_pin_to_irq_node(data, node, apic, pin))
-		panic("IO-APIC: failed to add irq-pin. Can not proceed\n");
-}
-
 /*
  * Reroute an IRQ to a different pin.
  */
@@ -1000,8 +992,7 @@
 	if (irq_data && irq_data->parent_data) {
 		if (!mp_check_pin_attr(irq, info))
 			return -EBUSY;
-		if (__add_pin_to_irq_node(irq_data->chip_data, node, ioapic,
-					  info->ioapic.pin))
+		if (!add_pin_to_irq_node(irq_data->chip_data, node, ioapic, info->ioapic.pin))
 			return -ENOMEM;
 	} else {
 		info->flags |= X86_IRQ_ALLOC_LEGACY;
@@ -2479,17 +2470,21 @@
 
 unsigned int arch_dynirq_lower_bound(unsigned int from)
 {
+	unsigned int ret;
+
 	/*
 	 * dmar_alloc_hwirq() may be called before setup_IO_APIC(), so use
 	 * gsi_top if ioapic_dynirq_base hasn't been initialized yet.
 	 */
-	if (!ioapic_initialized)
-		return gsi_top;
+	ret = ioapic_dynirq_base ? : gsi_top;
+
 	/*
-	 * For DT enabled machines ioapic_dynirq_base is irrelevant and not
-	 * updated. So simply return @from if ioapic_dynirq_base == 0.
+	 * For DT enabled machines ioapic_dynirq_base is irrelevant and
+	 * always 0. gsi_top can be 0 if there is no IO/APIC registered.
+	 * 0 is an invalid interrupt number for dynamic allocations. Return
+	 * @from instead.
 	 */
-	return ioapic_dynirq_base ? : from;
+	return ret ? : from;
 }
 
 #ifdef CONFIG_X86_32
@@ -3020,10 +3015,8 @@
 		return -ENOMEM;
 
 	ret = irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, info);
-	if (ret < 0) {
-		kfree(data);
-		return ret;
-	}
+	if (ret < 0)
+		goto free_data;
 
 	INIT_LIST_HEAD(&data->irq_2_pin);
 	irq_data->hwirq = info->ioapic.pin;
@@ -3032,7 +3025,10 @@
 	irq_data->chip_data = data;
 	mp_irqdomain_get_attr(mp_pin_to_gsi(ioapic, pin), data, info);
 
-	add_pin_to_irq_node(data, ioapic_alloc_attr_node(info), ioapic, pin);
+	if (!add_pin_to_irq_node(data, ioapic_alloc_attr_node(info), ioapic, pin)) {
+		ret = -ENOMEM;
+		goto free_irqs;
+	}
 
 	mp_preconfigure_entry(data);
 	mp_register_handler(virq, data->is_level);
@@ -3047,6 +3043,12 @@
 		    ioapic, mpc_ioapic_id(ioapic), pin, virq,
 		    data->is_level, data->active_low);
 	return 0;
+
+free_irqs:
+	irq_domain_free_irqs_parent(domain, virq, nr_irqs);
+free_data:
+	kfree(data);
+	return ret;
 }
 
 void mp_irqdomain_free(struct irq_domain *domain, unsigned int virq,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/apic/vector.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/apic/vector.c
@@ -982,7 +982,8 @@
 		hlist_add_head(&apicd->clist, per_cpu_ptr(&cleanup_list, cpu));
 		apic->send_IPI(cpu, IRQ_MOVE_CLEANUP_VECTOR);
 	} else {
-		apicd->prev_vector = 0;
+		pr_warn("IRQ %u schedule cleanup for offline CPU %u\n", apicd->irq, cpu);
+		free_moved_vector(apicd);
 	}
 	raw_spin_unlock(&vector_lock);
 }
@@ -1019,6 +1020,7 @@
  */
 void irq_force_complete_move(struct irq_desc *desc)
 {
+	unsigned int cpu = smp_processor_id();
 	struct apic_chip_data *apicd;
 	struct irq_data *irqd;
 	unsigned int vector;
@@ -1043,10 +1045,11 @@
 		goto unlock;
 
 	/*
-	 * If prev_vector is empty, no action required.
+	 * If prev_vector is empty or the descriptor is neither currently
+	 * nor previously on the outgoing CPU no action required.
 	 */
 	vector = apicd->prev_vector;
-	if (!vector)
+	if (!vector || (apicd->cpu != cpu && apicd->prev_cpu != cpu))
 		goto unlock;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/apic/x2apic_phys.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/apic/x2apic_phys.c
@@ -97,7 +97,10 @@
 
 static int x2apic_phys_probe(void)
 {
-	if (x2apic_mode && (x2apic_phys || x2apic_fadt_phys()))
+	if (!x2apic_mode)
+		return 0;
+
+	if (x2apic_phys || x2apic_fadt_phys())
 		return 1;
 
 	return apic == &apic_x2apic_phys;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/apic/x2apic_uv_x.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -199,7 +199,13 @@
 	int mmr_shift;
 	char *state;
 
-	/* Different returns from different UV BIOS versions */
+	/* UV5 guarantees synced TSCs; do not zero TSC_ADJUST */
+	if (!is_uv(UV2|UV3|UV4)) {
+		mark_tsc_async_resets("UV5+");
+		return;
+	}
+
+	/* UV2,3,4, UV BIOS TSC sync state available */
 	mmr = uv_early_read_mmr(UVH_TSC_SYNC_MMR);
 	mmr_shift =
 		is_uv2_hub() ? UVH_TSC_SYNC_SHIFT_UV2K : UVH_TSC_SYNC_SHIFT;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/apm_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/apm_32.c
@@ -238,12 +238,6 @@
 #endif
 
 /*
- * The apm_bios device is one of the misc char devices.
- * This is its minor number.
- */
-#define	APM_MINOR_DEV	134
-
-/*
  * Various options can be changed at boot time as follows:
  * (We allow underscores for compatibility with the modules code)
  *	apm=on/off			enable/disable APM
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/asm-offsets.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/asm-offsets.c
@@ -18,6 +18,7 @@
 #include <asm/bootparam.h>
 #include <asm/suspend.h>
 #include <asm/tlbflush.h>
+#include "../kvm/vmx/vmx.h"
 
 #ifdef CONFIG_XEN
 #include <xen/interface/xen.h>
@@ -93,4 +94,9 @@
 	OFFSET(TSS_sp0, tss_struct, x86_tss.sp0);
 	OFFSET(TSS_sp1, tss_struct, x86_tss.sp1);
 	OFFSET(TSS_sp2, tss_struct, x86_tss.sp2);
+
+	if (IS_ENABLED(CONFIG_KVM_INTEL)) {
+		BLANK();
+		OFFSET(VMX_spec_ctrl, vcpu_vmx, spec_ctrl);
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cc_platform.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cc_platform.c
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Confidential Computing Platform Capability checks
+ *
+ * Copyright (C) 2021 Advanced Micro Devices, Inc.
+ *
+ * Author: Tom Lendacky <thomas.lendacky@amd.com>
+ */
+
+#include <linux/export.h>
+#include <linux/cc_platform.h>
+#include <linux/mem_encrypt.h>
+
+#include <asm/processor.h>
+
+static bool __maybe_unused intel_cc_platform_has(enum cc_attr attr)
+{
+#ifdef CONFIG_INTEL_TDX_GUEST
+	return false;
+#else
+	return false;
+#endif
+}
+
+/*
+ * SME and SEV are very similar but they are not the same, so there are
+ * times that the kernel will need to distinguish between SME and SEV. The
+ * cc_platform_has() function is used for this.  When a distinction isn't
+ * needed, the CC_ATTR_MEM_ENCRYPT attribute can be used.
+ *
+ * The trampoline code is a good example for this requirement.  Before
+ * paging is activated, SME will access all memory as decrypted, but SEV
+ * will access all memory as encrypted.  So, when APs are being brought
+ * up under SME the trampoline area cannot be encrypted, whereas under SEV
+ * the trampoline area must be encrypted.
+ */
+static bool amd_cc_platform_has(enum cc_attr attr)
+{
+#ifdef CONFIG_AMD_MEM_ENCRYPT
+	switch (attr) {
+	case CC_ATTR_MEM_ENCRYPT:
+		return sme_me_mask;
+
+	case CC_ATTR_HOST_MEM_ENCRYPT:
+		return sme_me_mask && !(sev_status & MSR_AMD64_SEV_ENABLED);
+
+	case CC_ATTR_GUEST_MEM_ENCRYPT:
+		return sev_status & MSR_AMD64_SEV_ENABLED;
+
+	case CC_ATTR_GUEST_STATE_ENCRYPT:
+		return sev_status & MSR_AMD64_SEV_ES_ENABLED;
+
+	default:
+		return false;
+	}
+#else
+	return false;
+#endif
+}
+
+
+bool cc_platform_has(enum cc_attr attr)
+{
+	if (sme_me_mask)
+		return amd_cc_platform_has(attr);
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(cc_platform_has);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/amd.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/amd.c
@@ -13,6 +13,7 @@
 #include <asm/apic.h>
 #include <asm/cacheinfo.h>
 #include <asm/cpu.h>
+#include <asm/cpu_device_id.h>
 #include <asm/spec-ctrl.h>
 #include <asm/smp.h>
 #include <asm/numa.h>
@@ -27,11 +28,6 @@
 
 #include "cpu.h"
 
-static const int amd_erratum_383[];
-static const int amd_erratum_400[];
-static const int amd_erratum_1054[];
-static bool cpu_has_amd_erratum(struct cpuinfo_x86 *cpu, const int *erratum);
-
 /*
  * nodes_per_socket: Stores the number of nodes per socket.
  * Refer to Fam15h Models 00-0fh BKDG - CPUID Fn8000_001E_ECX
@@ -39,6 +35,87 @@
  */
 static u32 nodes_per_socket = 1;
 
+/*
+ * AMD errata checking
+ *
+ * Errata are defined as arrays of ints using the AMD_LEGACY_ERRATUM() or
+ * AMD_OSVW_ERRATUM() macros. The latter is intended for newer errata that
+ * have an OSVW id assigned, which it takes as first argument. Both take a
+ * variable number of family-specific model-stepping ranges created by
+ * AMD_MODEL_RANGE().
+ *
+ * Example:
+ *
+ * const int amd_erratum_319[] =
+ *	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x10, 0x2, 0x1, 0x4, 0x2),
+ *			   AMD_MODEL_RANGE(0x10, 0x8, 0x0, 0x8, 0x0),
+ *			   AMD_MODEL_RANGE(0x10, 0x9, 0x0, 0x9, 0x0));
+ */
+
+#define AMD_LEGACY_ERRATUM(...)		{ -1, __VA_ARGS__, 0 }
+#define AMD_OSVW_ERRATUM(osvw_id, ...)	{ osvw_id, __VA_ARGS__, 0 }
+#define AMD_MODEL_RANGE(f, m_start, s_start, m_end, s_end) \
+	((f << 24) | (m_start << 16) | (s_start << 12) | (m_end << 4) | (s_end))
+#define AMD_MODEL_RANGE_FAMILY(range)	(((range) >> 24) & 0xff)
+#define AMD_MODEL_RANGE_START(range)	(((range) >> 12) & 0xfff)
+#define AMD_MODEL_RANGE_END(range)	((range) & 0xfff)
+
+static const int amd_erratum_400[] =
+	AMD_OSVW_ERRATUM(1, AMD_MODEL_RANGE(0xf, 0x41, 0x2, 0xff, 0xf),
+			    AMD_MODEL_RANGE(0x10, 0x2, 0x1, 0xff, 0xf));
+
+static const int amd_erratum_383[] =
+	AMD_OSVW_ERRATUM(3, AMD_MODEL_RANGE(0x10, 0, 0, 0xff, 0xf));
+
+/* #1054: Instructions Retired Performance Counter May Be Inaccurate */
+static const int amd_erratum_1054[] =
+	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x17, 0, 0, 0x2f, 0xf));
+
+static const int amd_zenbleed[] =
+	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x17, 0x30, 0x0, 0x4f, 0xf),
+			   AMD_MODEL_RANGE(0x17, 0x60, 0x0, 0x7f, 0xf),
+			   AMD_MODEL_RANGE(0x17, 0x90, 0x0, 0x91, 0xf),
+			   AMD_MODEL_RANGE(0x17, 0xa0, 0x0, 0xaf, 0xf));
+
+static const int amd_div0[] =
+	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x17, 0x00, 0x0, 0x2f, 0xf),
+			   AMD_MODEL_RANGE(0x17, 0x50, 0x0, 0x5f, 0xf));
+
+static const int amd_erratum_1485[] =
+	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x19, 0x10, 0x0, 0x1f, 0xf),
+			   AMD_MODEL_RANGE(0x19, 0x60, 0x0, 0xaf, 0xf));
+
+static bool cpu_has_amd_erratum(struct cpuinfo_x86 *cpu, const int *erratum)
+{
+	int osvw_id = *erratum++;
+	u32 range;
+	u32 ms;
+
+	if (osvw_id >= 0 && osvw_id < 65536 &&
+	    cpu_has(cpu, X86_FEATURE_OSVW)) {
+		u64 osvw_len;
+
+		rdmsrl(MSR_AMD64_OSVW_ID_LENGTH, osvw_len);
+		if (osvw_id < osvw_len) {
+			u64 osvw_bits;
+
+			rdmsrl(MSR_AMD64_OSVW_STATUS + (osvw_id >> 6),
+			    osvw_bits);
+			return osvw_bits & (1ULL << (osvw_id & 0x3f));
+		}
+	}
+
+	/* OSVW unavailable or ID unknown, match family-model-stepping range */
+	ms = (cpu->x86_model << 4) | cpu->x86_stepping;
+	while ((range = *erratum++))
+		if ((cpu->x86 == AMD_MODEL_RANGE_FAMILY(range)) &&
+		    (ms >= AMD_MODEL_RANGE_START(range)) &&
+		    (ms <= AMD_MODEL_RANGE_END(range)))
+			return true;
+
+	return false;
+}
+
 static inline int rdmsrl_amd_safe(unsigned msr, unsigned long long *p)
 {
 	u32 gprs[8] = { 0 };
@@ -394,35 +471,6 @@
 	per_cpu(cpu_llc_id, cpu) = c->cpu_die_id = c->phys_proc_id;
 }
 
-static void amd_detect_ppin(struct cpuinfo_x86 *c)
-{
-	unsigned long long val;
-
-	if (!cpu_has(c, X86_FEATURE_AMD_PPIN))
-		return;
-
-	/* When PPIN is defined in CPUID, still need to check PPIN_CTL MSR */
-	if (rdmsrl_safe(MSR_AMD_PPIN_CTL, &val))
-		goto clear_ppin;
-
-	/* PPIN is locked in disabled mode, clear feature bit */
-	if ((val & 3UL) == 1UL)
-		goto clear_ppin;
-
-	/* If PPIN is disabled, try to enable it */
-	if (!(val & 2UL)) {
-		wrmsrl_safe(MSR_AMD_PPIN_CTL,  val | 2UL);
-		rdmsrl_safe(MSR_AMD_PPIN_CTL, &val);
-	}
-
-	/* If PPIN_EN bit is 1, return from here; otherwise fall through */
-	if (val & 2UL)
-		return;
-
-clear_ppin:
-	clear_cpu_cap(c, X86_FEATURE_AMD_PPIN);
-}
-
 u32 amd_get_nodes_per_socket(void)
 {
 	return nodes_per_socket;
@@ -794,8 +842,6 @@
 		set_cpu_bug(c, X86_BUG_AMD_TLB_MMATCH);
 }
 
-#define MSR_AMD64_DE_CFG	0xC0011029
-
 static void init_amd_ln(struct cpuinfo_x86 *c)
 {
 	/*
@@ -886,6 +932,49 @@
 	clear_rdrand_cpuid_bit(c);
 }
 
+static const struct x86_cpu_desc erratum_1386_microcode[] = {
+	AMD_CPU_DESC(0x17,  0x1, 0x2, 0x0800126e),
+	AMD_CPU_DESC(0x17, 0x31, 0x0, 0x08301052),
+	{},
+};
+
+void init_spectral_chicken(struct cpuinfo_x86 *c)
+{
+#ifdef CONFIG_CPU_UNRET_ENTRY
+	u64 value;
+
+	/*
+	 * On Zen2 we offer this chicken (bit) on the altar of Speculation.
+	 *
+	 * This suppresses speculation from the middle of a basic block, i.e. it
+	 * suppresses non-branch predictions.
+	 *
+	 * We use STIBP as a heuristic to filter out Zen2 from the rest of F17H
+	 */
+	if (!cpu_has(c, X86_FEATURE_HYPERVISOR) && cpu_has(c, X86_FEATURE_AMD_STIBP)) {
+		if (!rdmsrl_safe(MSR_ZEN2_SPECTRAL_CHICKEN, &value)) {
+			value |= MSR_ZEN2_SPECTRAL_CHICKEN_BIT;
+			wrmsrl_safe(MSR_ZEN2_SPECTRAL_CHICKEN, value);
+		}
+	}
+#endif
+	/*
+	 * Work around Erratum 1386.  The XSAVES instruction malfunctions in
+	 * certain circumstances on Zen1/2 uarch, and not all parts have had
+	 * updated microcode at the time of writing (March 2023).
+	 *
+	 * Affected parts all have no supervisor XSAVE states, meaning that
+	 * the XSAVEC instruction (which works fine) is equivalent.
+	 *
+	 * Clear the feature flag only on microcode revisions which
+	 * don't have the fix.
+	 */
+	if (x86_cpu_has_min_microcode_rev(erratum_1386_microcode))
+		return;
+
+	clear_cpu_cap(c, X86_FEATURE_XSAVES);
+}
+
 static void init_amd_zn(struct cpuinfo_x86 *c)
 {
 	set_cpu_cap(c, X86_FEATURE_ZEN);
@@ -894,12 +983,62 @@
 	node_reclaim_distance = 32;
 #endif
 
-	/*
-	 * Fix erratum 1076: CPB feature bit not being set in CPUID.
-	 * Always set it, except when running under a hypervisor.
-	 */
-	if (!cpu_has(c, X86_FEATURE_HYPERVISOR) && !cpu_has(c, X86_FEATURE_CPB))
-		set_cpu_cap(c, X86_FEATURE_CPB);
+	/* Fix up CPUID bits, but only if not virtualised. */
+	if (!cpu_has(c, X86_FEATURE_HYPERVISOR)) {
+
+		/* Erratum 1076: CPB feature bit not being set in CPUID. */
+		if (!cpu_has(c, X86_FEATURE_CPB))
+			set_cpu_cap(c, X86_FEATURE_CPB);
+
+		/*
+		 * Zen3 (Fam19 model < 0x10) parts are not susceptible to
+		 * Branch Type Confusion, but predate the allocation of the
+		 * BTC_NO bit.
+		 */
+		if (c->x86 == 0x19 && !cpu_has(c, X86_FEATURE_BTC_NO))
+			set_cpu_cap(c, X86_FEATURE_BTC_NO);
+	}
+}
+
+static bool cpu_has_zenbleed_microcode(void)
+{
+	u32 good_rev = 0;
+
+	switch (boot_cpu_data.x86_model) {
+	case 0x30 ... 0x3f: good_rev = 0x0830107b; break;
+	case 0x60 ... 0x67: good_rev = 0x0860010c; break;
+	case 0x68 ... 0x6f: good_rev = 0x08608107; break;
+	case 0x70 ... 0x7f: good_rev = 0x08701033; break;
+	case 0xa0 ... 0xaf: good_rev = 0x08a00009; break;
+
+	default:
+		return false;
+		break;
+	}
+
+	if (boot_cpu_data.microcode < good_rev)
+		return false;
+
+	return true;
+}
+
+static void zenbleed_check(struct cpuinfo_x86 *c)
+{
+	if (!cpu_has_amd_erratum(c, amd_zenbleed))
+		return;
+
+	if (cpu_has(c, X86_FEATURE_HYPERVISOR))
+		return;
+
+	if (!cpu_has(c, X86_FEATURE_AVX))
+		return;
+
+	if (!cpu_has_zenbleed_microcode()) {
+		pr_notice_once("Zenbleed: please update your microcode for the most optimal fix\n");
+		msr_set_bit(MSR_AMD64_DE_CFG, MSR_AMD64_DE_CFG_ZEN2_FP_BACKUP_FIX_BIT);
+	} else {
+		msr_clear_bit(MSR_AMD64_DE_CFG, MSR_AMD64_DE_CFG_ZEN2_FP_BACKUP_FIX_BIT);
+	}
 }
 
 static void init_amd(struct cpuinfo_x86 *c)
@@ -931,7 +1070,8 @@
 	case 0x12: init_amd_ln(c); break;
 	case 0x15: init_amd_bd(c); break;
 	case 0x16: init_amd_jg(c); break;
-	case 0x17: fallthrough;
+	case 0x17: init_spectral_chicken(c);
+		   fallthrough;
 	case 0x19: init_amd_zn(c); break;
 	}
 
@@ -947,7 +1087,6 @@
 	amd_detect_cmp(c);
 	amd_get_topology(c);
 	srat_detect_node(c);
-	amd_detect_ppin(c);
 
 	init_amd_cacheinfo(c);
 
@@ -958,8 +1097,8 @@
 		 * msr_set_bit() uses the safe accessors, too, even if the MSR
 		 * is not present.
 		 */
-		msr_set_bit(MSR_F10H_DECFG,
-			    MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT);
+		msr_set_bit(MSR_AMD64_DE_CFG,
+			    MSR_AMD64_DE_CFG_LFENCE_SERIALIZE_BIT);
 
 		/* A serializing LFENCE stops RDTSC speculation */
 		set_cpu_cap(c, X86_FEATURE_LFENCE_RDTSC);
@@ -989,6 +1128,22 @@
 	if (cpu_has(c, X86_FEATURE_IRPERF) &&
 	    !cpu_has_amd_erratum(c, amd_erratum_1054))
 		msr_set_bit(MSR_K7_HWCR, MSR_K7_HWCR_IRPERF_EN_BIT);
+
+	check_null_seg_clears_base(c);
+
+	zenbleed_check(c);
+
+	if (cpu_has_amd_erratum(c, amd_div0)) {
+		pr_notice_once("AMD Zen1 DIV0 bug detected. Disable SMT for full protection.\n");
+		setup_force_cpu_bug(X86_BUG_DIV0);
+	}
+
+	if (!cpu_has(c, X86_FEATURE_HYPERVISOR) &&
+	     cpu_has_amd_erratum(c, amd_erratum_1485))
+		msr_set_bit(MSR_ZEN4_BP_CFG, MSR_ZEN4_BP_CFG_SHARED_BTB_FIX_BIT);
+
+	/* AMD CPUs don't need fencing after x2APIC/TSC_DEADLINE MSR writes. */
+	clear_cpu_cap(c, X86_FEATURE_APIC_MSRS_FENCE);
 }
 
 #ifdef CONFIG_X86_32
@@ -1084,73 +1239,6 @@
 
 cpu_dev_register(amd_cpu_dev);
 
-/*
- * AMD errata checking
- *
- * Errata are defined as arrays of ints using the AMD_LEGACY_ERRATUM() or
- * AMD_OSVW_ERRATUM() macros. The latter is intended for newer errata that
- * have an OSVW id assigned, which it takes as first argument. Both take a
- * variable number of family-specific model-stepping ranges created by
- * AMD_MODEL_RANGE().
- *
- * Example:
- *
- * const int amd_erratum_319[] =
- *	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x10, 0x2, 0x1, 0x4, 0x2),
- *			   AMD_MODEL_RANGE(0x10, 0x8, 0x0, 0x8, 0x0),
- *			   AMD_MODEL_RANGE(0x10, 0x9, 0x0, 0x9, 0x0));
- */
-
-#define AMD_LEGACY_ERRATUM(...)		{ -1, __VA_ARGS__, 0 }
-#define AMD_OSVW_ERRATUM(osvw_id, ...)	{ osvw_id, __VA_ARGS__, 0 }
-#define AMD_MODEL_RANGE(f, m_start, s_start, m_end, s_end) \
-	((f << 24) | (m_start << 16) | (s_start << 12) | (m_end << 4) | (s_end))
-#define AMD_MODEL_RANGE_FAMILY(range)	(((range) >> 24) & 0xff)
-#define AMD_MODEL_RANGE_START(range)	(((range) >> 12) & 0xfff)
-#define AMD_MODEL_RANGE_END(range)	((range) & 0xfff)
-
-static const int amd_erratum_400[] =
-	AMD_OSVW_ERRATUM(1, AMD_MODEL_RANGE(0xf, 0x41, 0x2, 0xff, 0xf),
-			    AMD_MODEL_RANGE(0x10, 0x2, 0x1, 0xff, 0xf));
-
-static const int amd_erratum_383[] =
-	AMD_OSVW_ERRATUM(3, AMD_MODEL_RANGE(0x10, 0, 0, 0xff, 0xf));
-
-/* #1054: Instructions Retired Performance Counter May Be Inaccurate */
-static const int amd_erratum_1054[] =
-	AMD_LEGACY_ERRATUM(AMD_MODEL_RANGE(0x17, 0, 0, 0x2f, 0xf));
-
-static bool cpu_has_amd_erratum(struct cpuinfo_x86 *cpu, const int *erratum)
-{
-	int osvw_id = *erratum++;
-	u32 range;
-	u32 ms;
-
-	if (osvw_id >= 0 && osvw_id < 65536 &&
-	    cpu_has(cpu, X86_FEATURE_OSVW)) {
-		u64 osvw_len;
-
-		rdmsrl(MSR_AMD64_OSVW_ID_LENGTH, osvw_len);
-		if (osvw_id < osvw_len) {
-			u64 osvw_bits;
-
-			rdmsrl(MSR_AMD64_OSVW_STATUS + (osvw_id >> 6),
-			    osvw_bits);
-			return osvw_bits & (1ULL << (osvw_id & 0x3f));
-		}
-	}
-
-	/* OSVW unavailable or ID unknown, match family-model-stepping range */
-	ms = (cpu->x86_model << 4) | cpu->x86_stepping;
-	while ((range = *erratum++))
-		if ((cpu->x86 == AMD_MODEL_RANGE_FAMILY(range)) &&
-		    (ms >= AMD_MODEL_RANGE_START(range)) &&
-		    (ms <= AMD_MODEL_RANGE_END(range)))
-			return true;
-
-	return false;
-}
-
 void set_dr_addr_mask(unsigned long mask, int dr)
 {
 	if (!boot_cpu_has(X86_FEATURE_BPEXT))
@@ -1185,3 +1273,48 @@
 	return 255;
 }
 EXPORT_SYMBOL_GPL(amd_get_highest_perf);
+
+bool cpu_has_ibpb_brtype_microcode(void)
+{
+	switch (boot_cpu_data.x86) {
+	/* Zen1/2 IBPB flushes branch type predictions too. */
+	case 0x17:
+		return boot_cpu_has(X86_FEATURE_AMD_IBPB);
+	case 0x19:
+		/* Poke the MSR bit on Zen3/4 to check its presence. */
+		if (!wrmsrl_safe(MSR_IA32_PRED_CMD, PRED_CMD_SBPB)) {
+			setup_force_cpu_cap(X86_FEATURE_SBPB);
+			return true;
+		} else {
+			return false;
+		}
+	default:
+		return false;
+	}
+}
+
+static void zenbleed_check_cpu(void *unused)
+{
+	struct cpuinfo_x86 *c = &cpu_data(smp_processor_id());
+
+	zenbleed_check(c);
+}
+
+void amd_check_microcode(void)
+{
+	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
+		return;
+
+	on_each_cpu(zenbleed_check_cpu, NULL, 1);
+}
+
+/*
+ * Issue a DIV 0/1 insn to clear any division data from previous DIV
+ * operations.
+ */
+void noinstr amd_clear_divider(void)
+{
+	asm volatile(ALTERNATIVE("", "div %2\n\t", X86_BUG_DIV0)
+		     :: "a" (0), "d" (0), "r" (1));
+}
+EXPORT_SYMBOL_GPL(amd_clear_divider);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/bugs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/bugs.c
@@ -9,25 +9,23 @@
  *	- Andrew D. Balsa (code cleanup).
  */
 #include <linux/init.h>
-#include <linux/utsname.h>
 #include <linux/cpu.h>
 #include <linux/module.h>
 #include <linux/nospec.h>
 #include <linux/prctl.h>
 #include <linux/sched/smt.h>
 #include <linux/pgtable.h>
+#include <linux/bpf.h>
 
 #include <asm/spec-ctrl.h>
 #include <asm/cmdline.h>
 #include <asm/bugs.h>
 #include <asm/processor.h>
 #include <asm/processor-flags.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/msr.h>
 #include <asm/vmx.h>
 #include <asm/paravirt.h>
-#include <asm/alternative.h>
-#include <asm/set_memory.h>
 #include <asm/intel-family.h>
 #include <asm/e820/api.h>
 #include <asm/hypervisor.h>
@@ -37,24 +35,68 @@
 
 static void __init spectre_v1_select_mitigation(void);
 static void __init spectre_v2_select_mitigation(void);
+static void __init retbleed_select_mitigation(void);
+static void __init spectre_v2_user_select_mitigation(void);
 static void __init ssb_select_mitigation(void);
 static void __init l1tf_select_mitigation(void);
 static void __init mds_select_mitigation(void);
-static void __init mds_print_mitigation(void);
+static void __init md_clear_update_mitigation(void);
+static void __init md_clear_select_mitigation(void);
 static void __init taa_select_mitigation(void);
+static void __init mmio_select_mitigation(void);
 static void __init srbds_select_mitigation(void);
 static void __init l1d_flush_select_mitigation(void);
+static void __init gds_select_mitigation(void);
+static void __init srso_select_mitigation(void);
 
-/* The base value of the SPEC_CTRL MSR that always has to be preserved. */
+/* The base value of the SPEC_CTRL MSR without task-specific bits set */
 u64 x86_spec_ctrl_base;
 EXPORT_SYMBOL_GPL(x86_spec_ctrl_base);
+
+/* The current value of the SPEC_CTRL MSR with task-specific bits set */
+DEFINE_PER_CPU(u64, x86_spec_ctrl_current);
+EXPORT_SYMBOL_GPL(x86_spec_ctrl_current);
+
+u64 x86_pred_cmd __ro_after_init = PRED_CMD_IBPB;
+EXPORT_SYMBOL_GPL(x86_pred_cmd);
+
+static u64 __ro_after_init x86_arch_cap_msr;
+
 static DEFINE_MUTEX(spec_ctrl_mutex);
 
+void (*x86_return_thunk)(void) __ro_after_init = &__x86_return_thunk;
+
+/* Update SPEC_CTRL MSR and its cached copy unconditionally */
+static void update_spec_ctrl(u64 val)
+{
+	this_cpu_write(x86_spec_ctrl_current, val);
+	wrmsrl(MSR_IA32_SPEC_CTRL, val);
+}
+
 /*
- * The vendor and possibly platform specific bits which can be modified in
- * x86_spec_ctrl_base.
+ * Keep track of the SPEC_CTRL MSR value for the current task, which may differ
+ * from x86_spec_ctrl_base due to STIBP/SSB in __speculation_ctrl_update().
  */
-static u64 __ro_after_init x86_spec_ctrl_mask = SPEC_CTRL_IBRS;
+void update_spec_ctrl_cond(u64 val)
+{
+	if (this_cpu_read(x86_spec_ctrl_current) == val)
+		return;
+
+	this_cpu_write(x86_spec_ctrl_current, val);
+
+	/*
+	 * When KERNEL_IBRS this MSR is written on return-to-user, unless
+	 * forced the update can be delayed until that time.
+	 */
+	if (!cpu_feature_enabled(X86_FEATURE_KERNEL_IBRS))
+		wrmsrl(MSR_IA32_SPEC_CTRL, val);
+}
+
+u64 spec_ctrl_current(void)
+{
+	return this_cpu_read(x86_spec_ctrl_current);
+}
+EXPORT_SYMBOL_GPL(spec_ctrl_current);
 
 /*
  * AMD specific MSR info for Speculative Store Bypass control.
@@ -70,9 +112,6 @@
 /* Control unconditional IBPB in switch_mm() */
 DEFINE_STATIC_KEY_FALSE(switch_mm_always_ibpb);
 
-/* Control MDS CPU buffer clear before returning to user space */
-DEFINE_STATIC_KEY_FALSE(mds_user_clear);
-EXPORT_SYMBOL_GPL(mds_user_clear);
 /* Control MDS CPU buffer clear before idling (halt, mwait) */
 DEFINE_STATIC_KEY_FALSE(mds_idle_clear);
 EXPORT_SYMBOL_GPL(mds_idle_clear);
@@ -84,108 +123,70 @@
  */
 DEFINE_STATIC_KEY_FALSE(switch_mm_cond_l1d_flush);
 
-void __init check_bugs(void)
-{
-	identify_boot_cpu();
-
-	/*
-	 * identify_boot_cpu() initialized SMT support information, let the
-	 * core code know.
-	 */
-	cpu_smt_check_topology();
-
-	if (!IS_ENABLED(CONFIG_SMP)) {
-		pr_info("CPU: ");
-		print_cpu_info(&boot_cpu_data);
-	}
+/* Controls CPU Fill buffer clear before KVM guest MMIO accesses */
+DEFINE_STATIC_KEY_FALSE(mmio_stale_data_clear);
+EXPORT_SYMBOL_GPL(mmio_stale_data_clear);
 
+void __init cpu_select_mitigations(void)
+{
 	/*
 	 * Read the SPEC_CTRL MSR to account for reserved bits which may
 	 * have unknown values. AMD64_LS_CFG MSR is cached in the early AMD
 	 * init code as it is not enumerated and depends on the family.
 	 */
-	if (boot_cpu_has(X86_FEATURE_MSR_SPEC_CTRL))
+	if (cpu_feature_enabled(X86_FEATURE_MSR_SPEC_CTRL)) {
 		rdmsrl(MSR_IA32_SPEC_CTRL, x86_spec_ctrl_base);
 
-	/* Allow STIBP in MSR_SPEC_CTRL if supported */
-	if (boot_cpu_has(X86_FEATURE_STIBP))
-		x86_spec_ctrl_mask |= SPEC_CTRL_STIBP;
+		/*
+		 * Previously running kernel (kexec), may have some controls
+		 * turned ON. Clear them and let the mitigations setup below
+		 * rediscover them based on configuration.
+		 */
+		x86_spec_ctrl_base &= ~SPEC_CTRL_MITIGATIONS_MASK;
+	}
+
+	x86_arch_cap_msr = x86_read_arch_cap_msr();
 
 	/* Select the proper CPU mitigations before patching alternatives: */
 	spectre_v1_select_mitigation();
 	spectre_v2_select_mitigation();
-	ssb_select_mitigation();
-	l1tf_select_mitigation();
-	mds_select_mitigation();
-	taa_select_mitigation();
-	srbds_select_mitigation();
-	l1d_flush_select_mitigation();
-
 	/*
-	 * As MDS and TAA mitigations are inter-related, print MDS
-	 * mitigation until after TAA mitigation selection is done.
+	 * retbleed_select_mitigation() relies on the state set by
+	 * spectre_v2_select_mitigation(); specifically it wants to know about
+	 * spectre_v2=ibrs.
 	 */
-	mds_print_mitigation();
-
-	arch_smt_update();
-
-#ifdef CONFIG_X86_32
+	retbleed_select_mitigation();
 	/*
-	 * Check whether we are able to run this kernel safely on SMP.
-	 *
-	 * - i386 is no longer supported.
-	 * - In order to run on anything without a TSC, we need to be
-	 *   compiled for a i486.
+	 * spectre_v2_user_select_mitigation() relies on the state set by
+	 * retbleed_select_mitigation(); specifically the STIBP selection is
+	 * forced for UNRET or IBPB.
 	 */
-	if (boot_cpu_data.x86 < 4)
-		panic("Kernel requires i486+ for 'invlpg' and other features");
-
-	init_utsname()->machine[1] =
-		'0' + (boot_cpu_data.x86 > 6 ? 6 : boot_cpu_data.x86);
-	alternative_instructions();
-
-	fpu__init_check_bugs();
-#else /* CONFIG_X86_64 */
-	alternative_instructions();
+	spectre_v2_user_select_mitigation();
+	ssb_select_mitigation();
+	l1tf_select_mitigation();
+	md_clear_select_mitigation();
+	srbds_select_mitigation();
+	l1d_flush_select_mitigation();
 
 	/*
-	 * Make sure the first 2MB area is not mapped by huge pages
-	 * There are typically fixed size MTRRs in there and overlapping
-	 * MTRRs into large pages causes slow downs.
-	 *
-	 * Right now we don't do that with gbpages because there seems
-	 * very little benefit for that case.
+	 * srso_select_mitigation() depends and must run after
+	 * retbleed_select_mitigation().
 	 */
-	if (!direct_gbpages)
-		set_memory_4k((unsigned long)__va(0), 1);
-#endif
+	srso_select_mitigation();
+	gds_select_mitigation();
 }
 
+/*
+ * NOTE: This function is *only* called for SVM.  VMX spec_ctrl handling is
+ * done in vmenter.S.
+ */
 void
 x86_virt_spec_ctrl(u64 guest_spec_ctrl, u64 guest_virt_spec_ctrl, bool setguest)
 {
-	u64 msrval, guestval, hostval = x86_spec_ctrl_base;
+	u64 msrval, guestval = guest_spec_ctrl, hostval = spec_ctrl_current();
 	struct thread_info *ti = current_thread_info();
 
-	/* Is MSR_SPEC_CTRL implemented ? */
 	if (static_cpu_has(X86_FEATURE_MSR_SPEC_CTRL)) {
-		/*
-		 * Restrict guest_spec_ctrl to supported values. Clear the
-		 * modifiable bits in the host base value and or the
-		 * modifiable bits from the guest value.
-		 */
-		guestval = hostval & ~x86_spec_ctrl_mask;
-		guestval |= guest_spec_ctrl & x86_spec_ctrl_mask;
-
-		/* SSBD controlled in MSR_SPEC_CTRL */
-		if (static_cpu_has(X86_FEATURE_SPEC_CTRL_SSBD) ||
-		    static_cpu_has(X86_FEATURE_AMD_SSBD))
-			hostval |= ssbd_tif_to_spec_ctrl(ti->flags);
-
-		/* Conditional STIBP enabled? */
-		if (static_branch_unlikely(&switch_to_cond_stibp))
-			hostval |= stibp_tif_to_spec_ctrl(ti->flags);
-
 		if (hostval != guestval) {
 			msrval = setguest ? guestval : hostval;
 			wrmsrl(MSR_IA32_SPEC_CTRL, msrval);
@@ -258,7 +259,7 @@
 		if (!boot_cpu_has(X86_FEATURE_MD_CLEAR))
 			mds_mitigation = MDS_MITIGATION_VMWERV;
 
-		static_branch_enable(&mds_user_clear);
+		setup_force_cpu_cap(X86_FEATURE_CLEAR_CPU_BUF);
 
 		if (!boot_cpu_has(X86_BUG_MSBDS_ONLY) &&
 		    (mds_nosmt || cpu_mitigations_auto_nosmt()))
@@ -266,14 +267,6 @@
 	}
 }
 
-static void __init mds_print_mitigation(void)
-{
-	if (!boot_cpu_has_bug(X86_BUG_MDS) || cpu_mitigations_off())
-		return;
-
-	pr_info("%s\n", mds_strings[mds_mitigation]);
-}
-
 static int __init mds_cmdline(char *str)
 {
 	if (!boot_cpu_has_bug(X86_BUG_MDS))
@@ -318,8 +311,6 @@
 
 static void __init taa_select_mitigation(void)
 {
-	u64 ia32_cap;
-
 	if (!boot_cpu_has_bug(X86_BUG_TAA)) {
 		taa_mitigation = TAA_MITIGATION_OFF;
 		return;
@@ -328,7 +319,7 @@
 	/* TSX previously disabled by tsx=off */
 	if (!boot_cpu_has(X86_FEATURE_RTM)) {
 		taa_mitigation = TAA_MITIGATION_TSX_DISABLED;
-		goto out;
+		return;
 	}
 
 	if (cpu_mitigations_off()) {
@@ -342,7 +333,7 @@
 	 */
 	if (taa_mitigation == TAA_MITIGATION_OFF &&
 	    mds_mitigation == MDS_MITIGATION_OFF)
-		goto out;
+		return;
 
 	if (boot_cpu_has(X86_FEATURE_MD_CLEAR))
 		taa_mitigation = TAA_MITIGATION_VERW;
@@ -358,9 +349,8 @@
 	 * On MDS_NO=1 CPUs if ARCH_CAP_TSX_CTRL_MSR is not set, microcode
 	 * update is required.
 	 */
-	ia32_cap = x86_read_arch_cap_msr();
-	if ( (ia32_cap & ARCH_CAP_MDS_NO) &&
-	    !(ia32_cap & ARCH_CAP_TSX_CTRL_MSR))
+	if ( (x86_arch_cap_msr & ARCH_CAP_MDS_NO) &&
+	    !(x86_arch_cap_msr & ARCH_CAP_TSX_CTRL_MSR))
 		taa_mitigation = TAA_MITIGATION_UCODE_NEEDED;
 
 	/*
@@ -370,22 +360,10 @@
 	 * For guests that can't determine whether the correct microcode is
 	 * present on host, enable the mitigation for UCODE_NEEDED as well.
 	 */
-	static_branch_enable(&mds_user_clear);
+	setup_force_cpu_cap(X86_FEATURE_CLEAR_CPU_BUF);
 
 	if (taa_nosmt || cpu_mitigations_auto_nosmt())
 		cpu_smt_disable(false);
-
-	/*
-	 * Update MDS mitigation, if necessary, as the mds_user_clear is
-	 * now enabled for TAA mitigation.
-	 */
-	if (mds_mitigation == MDS_MITIGATION_OFF &&
-	    boot_cpu_has_bug(X86_BUG_MDS)) {
-		mds_mitigation = MDS_MITIGATION_FULL;
-		mds_select_mitigation();
-	}
-out:
-	pr_info("%s\n", taa_strings[taa_mitigation]);
 }
 
 static int __init tsx_async_abort_parse_cmdline(char *str)
@@ -410,6 +388,219 @@
 early_param("tsx_async_abort", tsx_async_abort_parse_cmdline);
 
 #undef pr_fmt
+#define pr_fmt(fmt)	"MMIO Stale Data: " fmt
+
+enum mmio_mitigations {
+	MMIO_MITIGATION_OFF,
+	MMIO_MITIGATION_UCODE_NEEDED,
+	MMIO_MITIGATION_VERW,
+};
+
+/* Default mitigation for Processor MMIO Stale Data vulnerabilities */
+static enum mmio_mitigations mmio_mitigation __ro_after_init = MMIO_MITIGATION_VERW;
+static bool mmio_nosmt __ro_after_init = false;
+
+static const char * const mmio_strings[] = {
+	[MMIO_MITIGATION_OFF]		= "Vulnerable",
+	[MMIO_MITIGATION_UCODE_NEEDED]	= "Vulnerable: Clear CPU buffers attempted, no microcode",
+	[MMIO_MITIGATION_VERW]		= "Mitigation: Clear CPU buffers",
+};
+
+static void __init mmio_select_mitigation(void)
+{
+	if (!boot_cpu_has_bug(X86_BUG_MMIO_STALE_DATA) ||
+	     boot_cpu_has_bug(X86_BUG_MMIO_UNKNOWN) ||
+	     cpu_mitigations_off()) {
+		mmio_mitigation = MMIO_MITIGATION_OFF;
+		return;
+	}
+
+	if (mmio_mitigation == MMIO_MITIGATION_OFF)
+		return;
+
+	/*
+	 * Enable CPU buffer clear mitigation for host and VMM, if also affected
+	 * by MDS or TAA. Otherwise, enable mitigation for VMM only.
+	 */
+	if (boot_cpu_has_bug(X86_BUG_MDS) || (boot_cpu_has_bug(X86_BUG_TAA) &&
+					      boot_cpu_has(X86_FEATURE_RTM)))
+		setup_force_cpu_cap(X86_FEATURE_CLEAR_CPU_BUF);
+
+	/*
+	 * X86_FEATURE_CLEAR_CPU_BUF could be enabled by other VERW based
+	 * mitigations, disable KVM-only mitigation in that case.
+	 */
+	if (boot_cpu_has(X86_FEATURE_CLEAR_CPU_BUF))
+		static_branch_disable(&mmio_stale_data_clear);
+	else
+		static_branch_enable(&mmio_stale_data_clear);
+
+	/*
+	 * If Processor-MMIO-Stale-Data bug is present and Fill Buffer data can
+	 * be propagated to uncore buffers, clearing the Fill buffers on idle
+	 * is required irrespective of SMT state.
+	 */
+	if (!(x86_arch_cap_msr & ARCH_CAP_FBSDP_NO))
+		static_branch_enable(&mds_idle_clear);
+
+	/*
+	 * Check if the system has the right microcode.
+	 *
+	 * CPU Fill buffer clear mitigation is enumerated by either an explicit
+	 * FB_CLEAR or by the presence of both MD_CLEAR and L1D_FLUSH on MDS
+	 * affected systems.
+	 */
+	if ((x86_arch_cap_msr & ARCH_CAP_FB_CLEAR) ||
+	    (boot_cpu_has(X86_FEATURE_MD_CLEAR) &&
+	     boot_cpu_has(X86_FEATURE_FLUSH_L1D) &&
+	     !(x86_arch_cap_msr & ARCH_CAP_MDS_NO)))
+		mmio_mitigation = MMIO_MITIGATION_VERW;
+	else
+		mmio_mitigation = MMIO_MITIGATION_UCODE_NEEDED;
+
+	if (mmio_nosmt || cpu_mitigations_auto_nosmt())
+		cpu_smt_disable(false);
+}
+
+static int __init mmio_stale_data_parse_cmdline(char *str)
+{
+	if (!boot_cpu_has_bug(X86_BUG_MMIO_STALE_DATA))
+		return 0;
+
+	if (!str)
+		return -EINVAL;
+
+	if (!strcmp(str, "off")) {
+		mmio_mitigation = MMIO_MITIGATION_OFF;
+	} else if (!strcmp(str, "full")) {
+		mmio_mitigation = MMIO_MITIGATION_VERW;
+	} else if (!strcmp(str, "full,nosmt")) {
+		mmio_mitigation = MMIO_MITIGATION_VERW;
+		mmio_nosmt = true;
+	}
+
+	return 0;
+}
+early_param("mmio_stale_data", mmio_stale_data_parse_cmdline);
+
+#undef pr_fmt
+#define pr_fmt(fmt)	"Register File Data Sampling: " fmt
+
+enum rfds_mitigations {
+	RFDS_MITIGATION_OFF,
+	RFDS_MITIGATION_VERW,
+	RFDS_MITIGATION_UCODE_NEEDED,
+};
+
+/* Default mitigation for Register File Data Sampling */
+static enum rfds_mitigations rfds_mitigation __ro_after_init =
+	IS_ENABLED(CONFIG_MITIGATION_RFDS) ? RFDS_MITIGATION_VERW : RFDS_MITIGATION_OFF;
+
+static const char * const rfds_strings[] = {
+	[RFDS_MITIGATION_OFF]			= "Vulnerable",
+	[RFDS_MITIGATION_VERW]			= "Mitigation: Clear Register File",
+	[RFDS_MITIGATION_UCODE_NEEDED]		= "Vulnerable: No microcode",
+};
+
+static void __init rfds_select_mitigation(void)
+{
+	if (!boot_cpu_has_bug(X86_BUG_RFDS) || cpu_mitigations_off()) {
+		rfds_mitigation = RFDS_MITIGATION_OFF;
+		return;
+	}
+	if (rfds_mitigation == RFDS_MITIGATION_OFF)
+		return;
+
+	if (x86_arch_cap_msr & ARCH_CAP_RFDS_CLEAR)
+		setup_force_cpu_cap(X86_FEATURE_CLEAR_CPU_BUF);
+	else
+		rfds_mitigation = RFDS_MITIGATION_UCODE_NEEDED;
+}
+
+static __init int rfds_parse_cmdline(char *str)
+{
+	if (!str)
+		return -EINVAL;
+
+	if (!boot_cpu_has_bug(X86_BUG_RFDS))
+		return 0;
+
+	if (!strcmp(str, "off"))
+		rfds_mitigation = RFDS_MITIGATION_OFF;
+	else if (!strcmp(str, "on"))
+		rfds_mitigation = RFDS_MITIGATION_VERW;
+
+	return 0;
+}
+early_param("reg_file_data_sampling", rfds_parse_cmdline);
+
+#undef pr_fmt
+#define pr_fmt(fmt)     "" fmt
+
+static void __init md_clear_update_mitigation(void)
+{
+	if (cpu_mitigations_off())
+		return;
+
+	if (!boot_cpu_has(X86_FEATURE_CLEAR_CPU_BUF))
+		goto out;
+
+	/*
+	 * X86_FEATURE_CLEAR_CPU_BUF is now enabled. Update MDS, TAA and MMIO
+	 * Stale Data mitigation, if necessary.
+	 */
+	if (mds_mitigation == MDS_MITIGATION_OFF &&
+	    boot_cpu_has_bug(X86_BUG_MDS)) {
+		mds_mitigation = MDS_MITIGATION_FULL;
+		mds_select_mitigation();
+	}
+	if (taa_mitigation == TAA_MITIGATION_OFF &&
+	    boot_cpu_has_bug(X86_BUG_TAA)) {
+		taa_mitigation = TAA_MITIGATION_VERW;
+		taa_select_mitigation();
+	}
+	/*
+	 * MMIO_MITIGATION_OFF is not checked here so that mmio_stale_data_clear
+	 * gets updated correctly as per X86_FEATURE_CLEAR_CPU_BUF state.
+	 */
+	if (boot_cpu_has_bug(X86_BUG_MMIO_STALE_DATA)) {
+		mmio_mitigation = MMIO_MITIGATION_VERW;
+		mmio_select_mitigation();
+	}
+	if (rfds_mitigation == RFDS_MITIGATION_OFF &&
+	    boot_cpu_has_bug(X86_BUG_RFDS)) {
+		rfds_mitigation = RFDS_MITIGATION_VERW;
+		rfds_select_mitigation();
+	}
+out:
+	if (boot_cpu_has_bug(X86_BUG_MDS))
+		pr_info("MDS: %s\n", mds_strings[mds_mitigation]);
+	if (boot_cpu_has_bug(X86_BUG_TAA))
+		pr_info("TAA: %s\n", taa_strings[taa_mitigation]);
+	if (boot_cpu_has_bug(X86_BUG_MMIO_STALE_DATA))
+		pr_info("MMIO Stale Data: %s\n", mmio_strings[mmio_mitigation]);
+	else if (boot_cpu_has_bug(X86_BUG_MMIO_UNKNOWN))
+		pr_info("MMIO Stale Data: Unknown: No mitigations\n");
+	if (boot_cpu_has_bug(X86_BUG_RFDS))
+		pr_info("Register File Data Sampling: %s\n", rfds_strings[rfds_mitigation]);
+}
+
+static void __init md_clear_select_mitigation(void)
+{
+	mds_select_mitigation();
+	taa_select_mitigation();
+	mmio_select_mitigation();
+	rfds_select_mitigation();
+
+	/*
+	 * As these mitigations are inter-related and rely on VERW instruction
+	 * to clear the microarchitural buffers, update and print their status
+	 * after mitigation selection is done for each of these vulnerabilities.
+	 */
+	md_clear_update_mitigation();
+}
+
+#undef pr_fmt
 #define pr_fmt(fmt)	"SRBDS: " fmt
 
 enum srbds_mitigations {
@@ -464,17 +655,16 @@
 
 static void __init srbds_select_mitigation(void)
 {
-	u64 ia32_cap;
-
 	if (!boot_cpu_has_bug(X86_BUG_SRBDS))
 		return;
 
 	/*
-	 * Check to see if this is one of the MDS_NO systems supporting
-	 * TSX that are only exposed to SRBDS when TSX is enabled.
+	 * Check to see if this is one of the MDS_NO systems supporting TSX that
+	 * are only exposed to SRBDS when TSX is enabled or when CPU is affected
+	 * by Processor MMIO Stale Data vulnerability.
 	 */
-	ia32_cap = x86_read_arch_cap_msr();
-	if ((ia32_cap & ARCH_CAP_MDS_NO) && !boot_cpu_has(X86_FEATURE_RTM))
+	if ((x86_arch_cap_msr & ARCH_CAP_MDS_NO) && !boot_cpu_has(X86_FEATURE_RTM) &&
+	    !boot_cpu_has_bug(X86_BUG_MMIO_STALE_DATA))
 		srbds_mitigation = SRBDS_MITIGATION_TSX_OFF;
 	else if (boot_cpu_has(X86_FEATURE_HYPERVISOR))
 		srbds_mitigation = SRBDS_MITIGATION_HYPERVISOR;
@@ -529,6 +719,149 @@
 early_param("l1d_flush", l1d_flush_parse_cmdline);
 
 #undef pr_fmt
+#define pr_fmt(fmt)	"GDS: " fmt
+
+enum gds_mitigations {
+	GDS_MITIGATION_OFF,
+	GDS_MITIGATION_UCODE_NEEDED,
+	GDS_MITIGATION_FORCE,
+	GDS_MITIGATION_FULL,
+	GDS_MITIGATION_FULL_LOCKED,
+	GDS_MITIGATION_HYPERVISOR,
+};
+
+#if IS_ENABLED(CONFIG_GDS_FORCE_MITIGATION)
+static enum gds_mitigations gds_mitigation __ro_after_init = GDS_MITIGATION_FORCE;
+#else
+static enum gds_mitigations gds_mitigation __ro_after_init = GDS_MITIGATION_FULL;
+#endif
+
+static const char * const gds_strings[] = {
+	[GDS_MITIGATION_OFF]		= "Vulnerable",
+	[GDS_MITIGATION_UCODE_NEEDED]	= "Vulnerable: No microcode",
+	[GDS_MITIGATION_FORCE]		= "Mitigation: AVX disabled, no microcode",
+	[GDS_MITIGATION_FULL]		= "Mitigation: Microcode",
+	[GDS_MITIGATION_FULL_LOCKED]	= "Mitigation: Microcode (locked)",
+	[GDS_MITIGATION_HYPERVISOR]	= "Unknown: Dependent on hypervisor status",
+};
+
+bool gds_ucode_mitigated(void)
+{
+	return (gds_mitigation == GDS_MITIGATION_FULL ||
+		gds_mitigation == GDS_MITIGATION_FULL_LOCKED);
+}
+EXPORT_SYMBOL_GPL(gds_ucode_mitigated);
+
+void update_gds_msr(void)
+{
+	u64 mcu_ctrl_after;
+	u64 mcu_ctrl;
+
+	switch (gds_mitigation) {
+	case GDS_MITIGATION_OFF:
+		rdmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_ctrl);
+		mcu_ctrl |= GDS_MITG_DIS;
+		break;
+	case GDS_MITIGATION_FULL_LOCKED:
+		/*
+		 * The LOCKED state comes from the boot CPU. APs might not have
+		 * the same state. Make sure the mitigation is enabled on all
+		 * CPUs.
+		 */
+	case GDS_MITIGATION_FULL:
+		rdmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_ctrl);
+		mcu_ctrl &= ~GDS_MITG_DIS;
+		break;
+	case GDS_MITIGATION_FORCE:
+	case GDS_MITIGATION_UCODE_NEEDED:
+	case GDS_MITIGATION_HYPERVISOR:
+		return;
+	};
+
+	wrmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_ctrl);
+
+	/*
+	 * Check to make sure that the WRMSR value was not ignored. Writes to
+	 * GDS_MITG_DIS will be ignored if this processor is locked but the boot
+	 * processor was not.
+	 */
+	rdmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_ctrl_after);
+	WARN_ON_ONCE(mcu_ctrl != mcu_ctrl_after);
+}
+
+static void __init gds_select_mitigation(void)
+{
+	u64 mcu_ctrl;
+
+	if (!boot_cpu_has_bug(X86_BUG_GDS))
+		return;
+
+	if (boot_cpu_has(X86_FEATURE_HYPERVISOR)) {
+		gds_mitigation = GDS_MITIGATION_HYPERVISOR;
+		goto out;
+	}
+
+	if (cpu_mitigations_off())
+		gds_mitigation = GDS_MITIGATION_OFF;
+	/* Will verify below that mitigation _can_ be disabled */
+
+	/* No microcode */
+	if (!(x86_arch_cap_msr & ARCH_CAP_GDS_CTRL)) {
+		if (gds_mitigation == GDS_MITIGATION_FORCE) {
+			/*
+			 * This only needs to be done on the boot CPU so do it
+			 * here rather than in update_gds_msr()
+			 */
+			setup_clear_cpu_cap(X86_FEATURE_AVX);
+			pr_warn("Microcode update needed! Disabling AVX as mitigation.\n");
+		} else {
+			gds_mitigation = GDS_MITIGATION_UCODE_NEEDED;
+		}
+		goto out;
+	}
+
+	/* Microcode has mitigation, use it */
+	if (gds_mitigation == GDS_MITIGATION_FORCE)
+		gds_mitigation = GDS_MITIGATION_FULL;
+
+	rdmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_ctrl);
+	if (mcu_ctrl & GDS_MITG_LOCKED) {
+		if (gds_mitigation == GDS_MITIGATION_OFF)
+			pr_warn("Mitigation locked. Disable failed.\n");
+
+		/*
+		 * The mitigation is selected from the boot CPU. All other CPUs
+		 * _should_ have the same state. If the boot CPU isn't locked
+		 * but others are then update_gds_msr() will WARN() of the state
+		 * mismatch. If the boot CPU is locked update_gds_msr() will
+		 * ensure the other CPUs have the mitigation enabled.
+		 */
+		gds_mitigation = GDS_MITIGATION_FULL_LOCKED;
+	}
+
+	update_gds_msr();
+out:
+	pr_info("%s\n", gds_strings[gds_mitigation]);
+}
+
+static int __init gds_parse_cmdline(char *str)
+{
+	if (!str)
+		return -EINVAL;
+
+	if (!boot_cpu_has_bug(X86_BUG_GDS))
+		return 0;
+
+	if (!strcmp(str, "off"))
+		gds_mitigation = GDS_MITIGATION_OFF;
+	else if (!strcmp(str, "force"))
+		gds_mitigation = GDS_MITIGATION_FORCE;
+
+	return 0;
+}
+early_param("gather_data_sampling", gds_parse_cmdline);
+
+#undef pr_fmt
 #define pr_fmt(fmt)     "Spectre V1 : " fmt
 
 enum spectre_v1_mitigation {
@@ -618,12 +951,200 @@
 }
 early_param("nospectre_v1", nospectre_v1_cmdline);
 
-#undef pr_fmt
-#define pr_fmt(fmt)     "Spectre V2 : " fmt
-
 static enum spectre_v2_mitigation spectre_v2_enabled __ro_after_init =
 	SPECTRE_V2_NONE;
 
+#undef pr_fmt
+#define pr_fmt(fmt)     "RETBleed: " fmt
+
+enum retbleed_mitigation {
+	RETBLEED_MITIGATION_NONE,
+	RETBLEED_MITIGATION_UNRET,
+	RETBLEED_MITIGATION_IBPB,
+	RETBLEED_MITIGATION_IBRS,
+	RETBLEED_MITIGATION_EIBRS,
+};
+
+enum retbleed_mitigation_cmd {
+	RETBLEED_CMD_OFF,
+	RETBLEED_CMD_AUTO,
+	RETBLEED_CMD_UNRET,
+	RETBLEED_CMD_IBPB,
+};
+
+static const char * const retbleed_strings[] = {
+	[RETBLEED_MITIGATION_NONE]	= "Vulnerable",
+	[RETBLEED_MITIGATION_UNRET]	= "Mitigation: untrained return thunk",
+	[RETBLEED_MITIGATION_IBPB]	= "Mitigation: IBPB",
+	[RETBLEED_MITIGATION_IBRS]	= "Mitigation: IBRS",
+	[RETBLEED_MITIGATION_EIBRS]	= "Mitigation: Enhanced IBRS",
+};
+
+static enum retbleed_mitigation retbleed_mitigation __ro_after_init =
+	RETBLEED_MITIGATION_NONE;
+static enum retbleed_mitigation_cmd retbleed_cmd __ro_after_init =
+	RETBLEED_CMD_AUTO;
+
+static int __ro_after_init retbleed_nosmt = false;
+
+static int __init retbleed_parse_cmdline(char *str)
+{
+	if (!str)
+		return -EINVAL;
+
+	while (str) {
+		char *next = strchr(str, ',');
+		if (next) {
+			*next = 0;
+			next++;
+		}
+
+		if (!strcmp(str, "off")) {
+			retbleed_cmd = RETBLEED_CMD_OFF;
+		} else if (!strcmp(str, "auto")) {
+			retbleed_cmd = RETBLEED_CMD_AUTO;
+		} else if (!strcmp(str, "unret")) {
+			retbleed_cmd = RETBLEED_CMD_UNRET;
+		} else if (!strcmp(str, "ibpb")) {
+			retbleed_cmd = RETBLEED_CMD_IBPB;
+		} else if (!strcmp(str, "nosmt")) {
+			retbleed_nosmt = true;
+		} else {
+			pr_err("Ignoring unknown retbleed option (%s).", str);
+		}
+
+		str = next;
+	}
+
+	return 0;
+}
+early_param("retbleed", retbleed_parse_cmdline);
+
+#define RETBLEED_UNTRAIN_MSG "WARNING: BTB untrained return thunk mitigation is only effective on AMD/Hygon!\n"
+#define RETBLEED_INTEL_MSG "WARNING: Spectre v2 mitigation leaves CPU vulnerable to RETBleed attacks, data leaks possible!\n"
+
+static void __init retbleed_select_mitigation(void)
+{
+	bool mitigate_smt = false;
+
+	if (!boot_cpu_has_bug(X86_BUG_RETBLEED) || cpu_mitigations_off())
+		return;
+
+	switch (retbleed_cmd) {
+	case RETBLEED_CMD_OFF:
+		return;
+
+	case RETBLEED_CMD_UNRET:
+		if (IS_ENABLED(CONFIG_CPU_UNRET_ENTRY)) {
+			retbleed_mitigation = RETBLEED_MITIGATION_UNRET;
+		} else {
+			pr_err("WARNING: kernel not compiled with CPU_UNRET_ENTRY.\n");
+			goto do_cmd_auto;
+		}
+		break;
+
+	case RETBLEED_CMD_IBPB:
+		if (!boot_cpu_has(X86_FEATURE_IBPB)) {
+			pr_err("WARNING: CPU does not support IBPB.\n");
+			goto do_cmd_auto;
+		} else if (IS_ENABLED(CONFIG_CPU_IBPB_ENTRY)) {
+			retbleed_mitigation = RETBLEED_MITIGATION_IBPB;
+		} else {
+			pr_err("WARNING: kernel not compiled with CPU_IBPB_ENTRY.\n");
+			goto do_cmd_auto;
+		}
+		break;
+
+do_cmd_auto:
+	case RETBLEED_CMD_AUTO:
+	default:
+		if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
+		    boot_cpu_data.x86_vendor == X86_VENDOR_HYGON) {
+			if (IS_ENABLED(CONFIG_CPU_UNRET_ENTRY))
+				retbleed_mitigation = RETBLEED_MITIGATION_UNRET;
+			else if (IS_ENABLED(CONFIG_CPU_IBPB_ENTRY) && boot_cpu_has(X86_FEATURE_IBPB))
+				retbleed_mitigation = RETBLEED_MITIGATION_IBPB;
+		}
+
+		/*
+		 * The Intel mitigation (IBRS or eIBRS) was already selected in
+		 * spectre_v2_select_mitigation().  'retbleed_mitigation' will
+		 * be set accordingly below.
+		 */
+
+		break;
+	}
+
+	switch (retbleed_mitigation) {
+	case RETBLEED_MITIGATION_UNRET:
+		setup_force_cpu_cap(X86_FEATURE_RETHUNK);
+		setup_force_cpu_cap(X86_FEATURE_UNRET);
+
+		if (IS_ENABLED(CONFIG_RETHUNK))
+			x86_return_thunk = retbleed_return_thunk;
+
+		if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD &&
+		    boot_cpu_data.x86_vendor != X86_VENDOR_HYGON)
+			pr_err(RETBLEED_UNTRAIN_MSG);
+
+		mitigate_smt = true;
+		break;
+
+	case RETBLEED_MITIGATION_IBPB:
+		setup_force_cpu_cap(X86_FEATURE_ENTRY_IBPB);
+		setup_force_cpu_cap(X86_FEATURE_IBPB_ON_VMEXIT);
+		mitigate_smt = true;
+
+		/*
+		 * IBPB on entry already obviates the need for
+		 * software-based untraining so clear those in case some
+		 * other mitigation like SRSO has selected them.
+		 */
+		setup_clear_cpu_cap(X86_FEATURE_UNRET);
+		setup_clear_cpu_cap(X86_FEATURE_RETHUNK);
+
+		/*
+		 * There is no need for RSB filling: entry_ibpb() ensures
+		 * all predictions, including the RSB, are invalidated,
+		 * regardless of IBPB implementation.
+		 */
+		setup_clear_cpu_cap(X86_FEATURE_RSB_VMEXIT);
+
+		break;
+
+	default:
+		break;
+	}
+
+	if (mitigate_smt && !boot_cpu_has(X86_FEATURE_STIBP) &&
+	    (retbleed_nosmt || cpu_mitigations_auto_nosmt()))
+		cpu_smt_disable(false);
+
+	/*
+	 * Let IBRS trump all on Intel without affecting the effects of the
+	 * retbleed= cmdline option.
+	 */
+	if (boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) {
+		switch (spectre_v2_enabled) {
+		case SPECTRE_V2_IBRS:
+			retbleed_mitigation = RETBLEED_MITIGATION_IBRS;
+			break;
+		case SPECTRE_V2_EIBRS:
+		case SPECTRE_V2_EIBRS_RETPOLINE:
+		case SPECTRE_V2_EIBRS_LFENCE:
+			retbleed_mitigation = RETBLEED_MITIGATION_EIBRS;
+			break;
+		default:
+			pr_err(RETBLEED_INTEL_MSG);
+		}
+	}
+
+	pr_info("%s\n", retbleed_strings[retbleed_mitigation]);
+}
+
+#undef pr_fmt
+#define pr_fmt(fmt)     "Spectre V2 : " fmt
+
 static enum spectre_v2_user_mitigation spectre_v2_user_stibp __ro_after_init =
 	SPECTRE_V2_USER_NONE;
 static enum spectre_v2_user_mitigation spectre_v2_user_ibpb __ro_after_init =
@@ -650,6 +1171,33 @@
 static inline const char *spectre_v2_module_string(void) { return ""; }
 #endif
 
+#define SPECTRE_V2_LFENCE_MSG "WARNING: LFENCE mitigation is not recommended for this CPU, data leaks possible!\n"
+#define SPECTRE_V2_EIBRS_EBPF_MSG "WARNING: Unprivileged eBPF is enabled with eIBRS on, data leaks possible via Spectre v2 BHB attacks!\n"
+#define SPECTRE_V2_EIBRS_LFENCE_EBPF_SMT_MSG "WARNING: Unprivileged eBPF is enabled with eIBRS+LFENCE mitigation and SMT, data leaks possible via Spectre v2 BHB attacks!\n"
+#define SPECTRE_V2_IBRS_PERF_MSG "WARNING: IBRS mitigation selected on Enhanced IBRS CPU, this may cause unnecessary performance loss\n"
+
+#ifdef CONFIG_BPF_SYSCALL
+void unpriv_ebpf_notify(int new_state)
+{
+	if (new_state)
+		return;
+
+	/* Unprivileged eBPF is enabled */
+
+	switch (spectre_v2_enabled) {
+	case SPECTRE_V2_EIBRS:
+		pr_err(SPECTRE_V2_EIBRS_EBPF_MSG);
+		break;
+	case SPECTRE_V2_EIBRS_LFENCE:
+		if (sched_smt_active())
+			pr_err(SPECTRE_V2_EIBRS_LFENCE_EBPF_SMT_MSG);
+		break;
+	default:
+		break;
+	}
+}
+#endif
+
 static inline bool match_option(const char *arg, int arglen, const char *opt)
 {
 	int len = strlen(opt);
@@ -664,7 +1212,11 @@
 	SPECTRE_V2_CMD_FORCE,
 	SPECTRE_V2_CMD_RETPOLINE,
 	SPECTRE_V2_CMD_RETPOLINE_GENERIC,
-	SPECTRE_V2_CMD_RETPOLINE_AMD,
+	SPECTRE_V2_CMD_RETPOLINE_LFENCE,
+	SPECTRE_V2_CMD_EIBRS,
+	SPECTRE_V2_CMD_EIBRS_RETPOLINE,
+	SPECTRE_V2_CMD_EIBRS_LFENCE,
+	SPECTRE_V2_CMD_IBRS,
 };
 
 enum spectre_v2_user_cmd {
@@ -705,13 +1257,15 @@
 		pr_info("spectre_v2_user=%s forced on command line.\n", reason);
 }
 
+static __ro_after_init enum spectre_v2_mitigation_cmd spectre_v2_cmd;
+
 static enum spectre_v2_user_cmd __init
-spectre_v2_parse_user_cmdline(enum spectre_v2_mitigation_cmd v2_cmd)
+spectre_v2_parse_user_cmdline(void)
 {
 	char arg[20];
 	int ret, i;
 
-	switch (v2_cmd) {
+	switch (spectre_v2_cmd) {
 	case SPECTRE_V2_CMD_NONE:
 		return SPECTRE_V2_USER_CMD_NONE;
 	case SPECTRE_V2_CMD_FORCE:
@@ -737,8 +1291,20 @@
 	return SPECTRE_V2_USER_CMD_AUTO;
 }
 
+static inline bool spectre_v2_in_eibrs_mode(enum spectre_v2_mitigation mode)
+{
+	return mode == SPECTRE_V2_EIBRS ||
+	       mode == SPECTRE_V2_EIBRS_RETPOLINE ||
+	       mode == SPECTRE_V2_EIBRS_LFENCE;
+}
+
+static inline bool spectre_v2_in_ibrs_mode(enum spectre_v2_mitigation mode)
+{
+	return spectre_v2_in_eibrs_mode(mode) || mode == SPECTRE_V2_IBRS;
+}
+
 static void __init
-spectre_v2_user_select_mitigation(enum spectre_v2_mitigation_cmd v2_cmd)
+spectre_v2_user_select_mitigation(void)
 {
 	enum spectre_v2_user_mitigation mode = SPECTRE_V2_USER_NONE;
 	bool smt_possible = IS_ENABLED(CONFIG_SMP);
@@ -751,7 +1317,7 @@
 	    cpu_smt_control == CPU_SMT_NOT_SUPPORTED)
 		smt_possible = false;
 
-	cmd = spectre_v2_parse_user_cmdline(v2_cmd);
+	cmd = spectre_v2_parse_user_cmdline();
 	switch (cmd) {
 	case SPECTRE_V2_USER_CMD_NONE:
 		goto set_mode;
@@ -799,12 +1365,21 @@
 	}
 
 	/*
-	 * If no STIBP, enhanced IBRS is enabled or SMT impossible, STIBP is not
-	 * required.
+	 * If no STIBP, Intel enhanced IBRS is enabled, or SMT impossible, STIBP
+	 * is not required.
+	 *
+	 * Intel's Enhanced IBRS also protects against cross-thread branch target
+	 * injection in user-mode as the IBRS bit remains always set which
+	 * implicitly enables cross-thread protections.  However, in legacy IBRS
+	 * mode, the IBRS bit is set only on kernel entry and cleared on return
+	 * to userspace.  AMD Automatic IBRS also does not protect userspace.
+	 * These modes therefore disable the implicit cross-thread protection,
+	 * so allow for STIBP to be selected in those cases.
 	 */
 	if (!boot_cpu_has(X86_FEATURE_STIBP) ||
 	    !smt_possible ||
-	    spectre_v2_enabled == SPECTRE_V2_IBRS_ENHANCED)
+	    (spectre_v2_in_eibrs_mode(spectre_v2_enabled) &&
+	     !boot_cpu_has(X86_FEATURE_AUTOIBRS)))
 		return;
 
 	/*
@@ -816,6 +1391,14 @@
 	    boot_cpu_has(X86_FEATURE_AMD_STIBP_ALWAYS_ON))
 		mode = SPECTRE_V2_USER_STRICT_PREFERRED;
 
+	if (retbleed_mitigation == RETBLEED_MITIGATION_UNRET ||
+	    retbleed_mitigation == RETBLEED_MITIGATION_IBPB) {
+		if (mode != SPECTRE_V2_USER_STRICT &&
+		    mode != SPECTRE_V2_USER_STRICT_PREFERRED)
+			pr_info("Selecting STIBP always-on mode to complement retbleed mitigation\n");
+		mode = SPECTRE_V2_USER_STRICT_PREFERRED;
+	}
+
 	spectre_v2_user_stibp = mode;
 
 set_mode:
@@ -824,9 +1407,12 @@
 
 static const char * const spectre_v2_strings[] = {
 	[SPECTRE_V2_NONE]			= "Vulnerable",
-	[SPECTRE_V2_RETPOLINE_GENERIC]		= "Mitigation: Full generic retpoline",
-	[SPECTRE_V2_RETPOLINE_AMD]		= "Mitigation: Full AMD retpoline",
-	[SPECTRE_V2_IBRS_ENHANCED]		= "Mitigation: Enhanced IBRS",
+	[SPECTRE_V2_RETPOLINE]			= "Mitigation: Retpolines",
+	[SPECTRE_V2_LFENCE]			= "Mitigation: LFENCE",
+	[SPECTRE_V2_EIBRS]			= "Mitigation: Enhanced / Automatic IBRS",
+	[SPECTRE_V2_EIBRS_LFENCE]		= "Mitigation: Enhanced / Automatic IBRS + LFENCE",
+	[SPECTRE_V2_EIBRS_RETPOLINE]		= "Mitigation: Enhanced / Automatic IBRS + Retpolines",
+	[SPECTRE_V2_IBRS]			= "Mitigation: IBRS",
 };
 
 static const struct {
@@ -837,9 +1423,14 @@
 	{ "off",		SPECTRE_V2_CMD_NONE,		  false },
 	{ "on",			SPECTRE_V2_CMD_FORCE,		  true  },
 	{ "retpoline",		SPECTRE_V2_CMD_RETPOLINE,	  false },
-	{ "retpoline,amd",	SPECTRE_V2_CMD_RETPOLINE_AMD,	  false },
+	{ "retpoline,amd",	SPECTRE_V2_CMD_RETPOLINE_LFENCE,  false },
+	{ "retpoline,lfence",	SPECTRE_V2_CMD_RETPOLINE_LFENCE,  false },
 	{ "retpoline,generic",	SPECTRE_V2_CMD_RETPOLINE_GENERIC, false },
+	{ "eibrs",		SPECTRE_V2_CMD_EIBRS,		  false },
+	{ "eibrs,lfence",	SPECTRE_V2_CMD_EIBRS_LFENCE,	  false },
+	{ "eibrs,retpoline",	SPECTRE_V2_CMD_EIBRS_RETPOLINE,	  false },
 	{ "auto",		SPECTRE_V2_CMD_AUTO,		  false },
+	{ "ibrs",		SPECTRE_V2_CMD_IBRS,              false },
 };
 
 static void __init spec_v2_print_cond(const char *reason, bool secure)
@@ -875,17 +1466,54 @@
 	}
 
 	if ((cmd == SPECTRE_V2_CMD_RETPOLINE ||
-	     cmd == SPECTRE_V2_CMD_RETPOLINE_AMD ||
-	     cmd == SPECTRE_V2_CMD_RETPOLINE_GENERIC) &&
+	     cmd == SPECTRE_V2_CMD_RETPOLINE_LFENCE ||
+	     cmd == SPECTRE_V2_CMD_RETPOLINE_GENERIC ||
+	     cmd == SPECTRE_V2_CMD_EIBRS_LFENCE ||
+	     cmd == SPECTRE_V2_CMD_EIBRS_RETPOLINE) &&
 	    !IS_ENABLED(CONFIG_RETPOLINE)) {
-		pr_err("%s selected but not compiled in. Switching to AUTO select\n", mitigation_options[i].option);
+		pr_err("%s selected but not compiled in. Switching to AUTO select\n",
+		       mitigation_options[i].option);
+		return SPECTRE_V2_CMD_AUTO;
+	}
+
+	if ((cmd == SPECTRE_V2_CMD_EIBRS ||
+	     cmd == SPECTRE_V2_CMD_EIBRS_LFENCE ||
+	     cmd == SPECTRE_V2_CMD_EIBRS_RETPOLINE) &&
+	    !boot_cpu_has(X86_FEATURE_IBRS_ENHANCED)) {
+		pr_err("%s selected but CPU doesn't have Enhanced or Automatic IBRS. Switching to AUTO select\n",
+		       mitigation_options[i].option);
+		return SPECTRE_V2_CMD_AUTO;
+	}
+
+	if ((cmd == SPECTRE_V2_CMD_RETPOLINE_LFENCE ||
+	     cmd == SPECTRE_V2_CMD_EIBRS_LFENCE) &&
+	    !boot_cpu_has(X86_FEATURE_LFENCE_RDTSC)) {
+		pr_err("%s selected, but CPU doesn't have a serializing LFENCE. Switching to AUTO select\n",
+		       mitigation_options[i].option);
+		return SPECTRE_V2_CMD_AUTO;
+	}
+
+	if (cmd == SPECTRE_V2_CMD_IBRS && !IS_ENABLED(CONFIG_CPU_IBRS_ENTRY)) {
+		pr_err("%s selected but not compiled in. Switching to AUTO select\n",
+		       mitigation_options[i].option);
+		return SPECTRE_V2_CMD_AUTO;
+	}
+
+	if (cmd == SPECTRE_V2_CMD_IBRS && boot_cpu_data.x86_vendor != X86_VENDOR_INTEL) {
+		pr_err("%s selected but not Intel CPU. Switching to AUTO select\n",
+		       mitigation_options[i].option);
 		return SPECTRE_V2_CMD_AUTO;
 	}
 
-	if (cmd == SPECTRE_V2_CMD_RETPOLINE_AMD &&
-	    boot_cpu_data.x86_vendor != X86_VENDOR_HYGON &&
-	    boot_cpu_data.x86_vendor != X86_VENDOR_AMD) {
-		pr_err("retpoline,amd selected but CPU is not AMD. Switching to AUTO select\n");
+	if (cmd == SPECTRE_V2_CMD_IBRS && !boot_cpu_has(X86_FEATURE_IBRS)) {
+		pr_err("%s selected but CPU doesn't have IBRS. Switching to AUTO select\n",
+		       mitigation_options[i].option);
+		return SPECTRE_V2_CMD_AUTO;
+	}
+
+	if (cmd == SPECTRE_V2_CMD_IBRS && boot_cpu_has(X86_FEATURE_XENPV)) {
+		pr_err("%s selected but running as XenPV guest. Switching to AUTO select\n",
+		       mitigation_options[i].option);
 		return SPECTRE_V2_CMD_AUTO;
 	}
 
@@ -894,6 +1522,152 @@
 	return cmd;
 }
 
+static enum spectre_v2_mitigation __init spectre_v2_select_retpoline(void)
+{
+	if (!IS_ENABLED(CONFIG_RETPOLINE)) {
+		pr_err("Kernel not compiled with retpoline; no mitigation available!");
+		return SPECTRE_V2_NONE;
+	}
+
+	return SPECTRE_V2_RETPOLINE;
+}
+
+static bool __ro_after_init rrsba_disabled;
+
+/* Disable in-kernel use of non-RSB RET predictors */
+static void __init spec_ctrl_disable_kernel_rrsba(void)
+{
+	if (rrsba_disabled)
+		return;
+
+	if (!(x86_arch_cap_msr & ARCH_CAP_RRSBA)) {
+		rrsba_disabled = true;
+		return;
+	}
+
+	if (!boot_cpu_has(X86_FEATURE_RRSBA_CTRL))
+		return;
+
+	x86_spec_ctrl_base |= SPEC_CTRL_RRSBA_DIS_S;
+	update_spec_ctrl(x86_spec_ctrl_base);
+	rrsba_disabled = true;
+}
+
+static void __init spectre_v2_determine_rsb_fill_type_at_vmexit(enum spectre_v2_mitigation mode)
+{
+	/*
+	 * Similar to context switches, there are two types of RSB attacks
+	 * after VM exit:
+	 *
+	 * 1) RSB underflow
+	 *
+	 * 2) Poisoned RSB entry
+	 *
+	 * When retpoline is enabled, both are mitigated by filling/clearing
+	 * the RSB.
+	 *
+	 * When IBRS is enabled, while #1 would be mitigated by the IBRS branch
+	 * prediction isolation protections, RSB still needs to be cleared
+	 * because of #2.  Note that SMEP provides no protection here, unlike
+	 * user-space-poisoned RSB entries.
+	 *
+	 * eIBRS should protect against RSB poisoning, but if the EIBRS_PBRSB
+	 * bug is present then a LITE version of RSB protection is required,
+	 * just a single call needs to retire before a RET is executed.
+	 */
+	switch (mode) {
+	case SPECTRE_V2_NONE:
+		return;
+
+	case SPECTRE_V2_EIBRS_LFENCE:
+	case SPECTRE_V2_EIBRS:
+		if (boot_cpu_has_bug(X86_BUG_EIBRS_PBRSB)) {
+			setup_force_cpu_cap(X86_FEATURE_RSB_VMEXIT_LITE);
+			pr_info("Spectre v2 / PBRSB-eIBRS: Retire a single CALL on VMEXIT\n");
+		}
+		return;
+
+	case SPECTRE_V2_EIBRS_RETPOLINE:
+	case SPECTRE_V2_RETPOLINE:
+	case SPECTRE_V2_LFENCE:
+	case SPECTRE_V2_IBRS:
+		setup_force_cpu_cap(X86_FEATURE_RSB_VMEXIT);
+		pr_info("Spectre v2 / SpectreRSB : Filling RSB on VMEXIT\n");
+		return;
+	}
+
+	pr_warn_once("Unknown Spectre v2 mode, disabling RSB mitigation at VM exit");
+	dump_stack();
+}
+
+/*
+ * Set BHI_DIS_S to prevent indirect branches in kernel to be influenced by
+ * branch history in userspace. Not needed if BHI_NO is set.
+ */
+static bool __init spec_ctrl_bhi_dis(void)
+{
+	if (!boot_cpu_has(X86_FEATURE_BHI_CTRL))
+		return false;
+
+	x86_spec_ctrl_base |= SPEC_CTRL_BHI_DIS_S;
+	update_spec_ctrl(x86_spec_ctrl_base);
+	setup_force_cpu_cap(X86_FEATURE_CLEAR_BHB_HW);
+
+	return true;
+}
+
+enum bhi_mitigations {
+	BHI_MITIGATION_OFF,
+	BHI_MITIGATION_ON,
+};
+
+static enum bhi_mitigations bhi_mitigation __ro_after_init =
+	IS_ENABLED(CONFIG_MITIGATION_SPECTRE_BHI) ? BHI_MITIGATION_ON : BHI_MITIGATION_OFF;
+
+static int __init spectre_bhi_parse_cmdline(char *str)
+{
+	if (!str)
+		return -EINVAL;
+
+	if (!strcmp(str, "off"))
+		bhi_mitigation = BHI_MITIGATION_OFF;
+	else if (!strcmp(str, "on"))
+		bhi_mitigation = BHI_MITIGATION_ON;
+	else
+		pr_err("Ignoring unknown spectre_bhi option (%s)", str);
+
+	return 0;
+}
+early_param("spectre_bhi", spectre_bhi_parse_cmdline);
+
+static void __init bhi_select_mitigation(void)
+{
+	if (bhi_mitigation == BHI_MITIGATION_OFF)
+		return;
+
+	/* Retpoline mitigates against BHI unless the CPU has RRSBA behavior */
+	if (boot_cpu_has(X86_FEATURE_RETPOLINE) &&
+	    !boot_cpu_has(X86_FEATURE_RETPOLINE_LFENCE)) {
+		spec_ctrl_disable_kernel_rrsba();
+		if (rrsba_disabled)
+			return;
+	}
+
+	if (spec_ctrl_bhi_dis())
+		return;
+
+	if (!IS_ENABLED(CONFIG_X86_64))
+		return;
+
+	/* Mitigate KVM by default */
+	setup_force_cpu_cap(X86_FEATURE_CLEAR_BHB_LOOP_ON_VMEXIT);
+	pr_info("Spectre BHI mitigation: SW BHB clearing on vm exit\n");
+
+	/* Mitigate syscalls when the mitigation is forced =on */
+	setup_force_cpu_cap(X86_FEATURE_CLEAR_BHB_LOOP);
+	pr_info("Spectre BHI mitigation: SW BHB clearing on syscall\n");
+}
+
 static void __init spectre_v2_select_mitigation(void)
 {
 	enum spectre_v2_mitigation_cmd cmd = spectre_v2_parse_cmdline();
@@ -914,86 +1688,179 @@
 	case SPECTRE_V2_CMD_FORCE:
 	case SPECTRE_V2_CMD_AUTO:
 		if (boot_cpu_has(X86_FEATURE_IBRS_ENHANCED)) {
-			mode = SPECTRE_V2_IBRS_ENHANCED;
-			/* Force it so VMEXIT will restore correctly */
-			x86_spec_ctrl_base |= SPEC_CTRL_IBRS;
-			wrmsrl(MSR_IA32_SPEC_CTRL, x86_spec_ctrl_base);
-			goto specv2_set_mode;
+			mode = SPECTRE_V2_EIBRS;
+			break;
+		}
+
+		if (IS_ENABLED(CONFIG_CPU_IBRS_ENTRY) &&
+		    boot_cpu_has_bug(X86_BUG_RETBLEED) &&
+		    retbleed_cmd != RETBLEED_CMD_OFF &&
+		    boot_cpu_has(X86_FEATURE_IBRS) &&
+		    boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) {
+			mode = SPECTRE_V2_IBRS;
+			break;
 		}
-		if (IS_ENABLED(CONFIG_RETPOLINE))
-			goto retpoline_auto;
+
+		mode = spectre_v2_select_retpoline();
 		break;
-	case SPECTRE_V2_CMD_RETPOLINE_AMD:
-		if (IS_ENABLED(CONFIG_RETPOLINE))
-			goto retpoline_amd;
+
+	case SPECTRE_V2_CMD_RETPOLINE_LFENCE:
+		pr_err(SPECTRE_V2_LFENCE_MSG);
+		mode = SPECTRE_V2_LFENCE;
 		break;
+
 	case SPECTRE_V2_CMD_RETPOLINE_GENERIC:
-		if (IS_ENABLED(CONFIG_RETPOLINE))
-			goto retpoline_generic;
+		mode = SPECTRE_V2_RETPOLINE;
 		break;
+
 	case SPECTRE_V2_CMD_RETPOLINE:
-		if (IS_ENABLED(CONFIG_RETPOLINE))
-			goto retpoline_auto;
+		mode = spectre_v2_select_retpoline();
+		break;
+
+	case SPECTRE_V2_CMD_IBRS:
+		mode = SPECTRE_V2_IBRS;
+		break;
+
+	case SPECTRE_V2_CMD_EIBRS:
+		mode = SPECTRE_V2_EIBRS;
+		break;
+
+	case SPECTRE_V2_CMD_EIBRS_LFENCE:
+		mode = SPECTRE_V2_EIBRS_LFENCE;
+		break;
+
+	case SPECTRE_V2_CMD_EIBRS_RETPOLINE:
+		mode = SPECTRE_V2_EIBRS_RETPOLINE;
 		break;
 	}
-	pr_err("Spectre mitigation: kernel not compiled with retpoline; no mitigation available!");
-	return;
 
-retpoline_auto:
-	if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
-	    boot_cpu_data.x86_vendor == X86_VENDOR_HYGON) {
-	retpoline_amd:
-		if (!boot_cpu_has(X86_FEATURE_LFENCE_RDTSC)) {
-			pr_err("Spectre mitigation: LFENCE not serializing, switching to generic retpoline\n");
-			goto retpoline_generic;
+	if (mode == SPECTRE_V2_EIBRS && unprivileged_ebpf_enabled())
+		pr_err(SPECTRE_V2_EIBRS_EBPF_MSG);
+
+	if (spectre_v2_in_ibrs_mode(mode)) {
+		if (boot_cpu_has(X86_FEATURE_AUTOIBRS)) {
+			msr_set_bit(MSR_EFER, _EFER_AUTOIBRS);
+		} else {
+			x86_spec_ctrl_base |= SPEC_CTRL_IBRS;
+			update_spec_ctrl(x86_spec_ctrl_base);
 		}
-		mode = SPECTRE_V2_RETPOLINE_AMD;
-		setup_force_cpu_cap(X86_FEATURE_RETPOLINE_AMD);
-		setup_force_cpu_cap(X86_FEATURE_RETPOLINE);
-	} else {
-	retpoline_generic:
-		mode = SPECTRE_V2_RETPOLINE_GENERIC;
+	}
+
+	switch (mode) {
+	case SPECTRE_V2_NONE:
+	case SPECTRE_V2_EIBRS:
+		break;
+
+	case SPECTRE_V2_IBRS:
+		setup_force_cpu_cap(X86_FEATURE_KERNEL_IBRS);
+		if (boot_cpu_has(X86_FEATURE_IBRS_ENHANCED))
+			pr_warn(SPECTRE_V2_IBRS_PERF_MSG);
+		break;
+
+	case SPECTRE_V2_LFENCE:
+	case SPECTRE_V2_EIBRS_LFENCE:
+		setup_force_cpu_cap(X86_FEATURE_RETPOLINE_LFENCE);
+		fallthrough;
+
+	case SPECTRE_V2_RETPOLINE:
+	case SPECTRE_V2_EIBRS_RETPOLINE:
 		setup_force_cpu_cap(X86_FEATURE_RETPOLINE);
+		break;
 	}
 
-specv2_set_mode:
+	/*
+	 * Disable alternate RSB predictions in kernel when indirect CALLs and
+	 * JMPs gets protection against BHI and Intramode-BTI, but RET
+	 * prediction from a non-RSB predictor is still a risk.
+	 */
+	if (mode == SPECTRE_V2_EIBRS_LFENCE ||
+	    mode == SPECTRE_V2_EIBRS_RETPOLINE ||
+	    mode == SPECTRE_V2_RETPOLINE)
+		spec_ctrl_disable_kernel_rrsba();
+
+	if (boot_cpu_has(X86_BUG_BHI))
+		bhi_select_mitigation();
+
 	spectre_v2_enabled = mode;
 	pr_info("%s\n", spectre_v2_strings[mode]);
 
 	/*
-	 * If spectre v2 protection has been enabled, unconditionally fill
-	 * RSB during a context switch; this protects against two independent
-	 * issues:
+	 * If Spectre v2 protection has been enabled, fill the RSB during a
+	 * context switch.  In general there are two types of RSB attacks
+	 * across context switches, for which the CALLs/RETs may be unbalanced.
+	 *
+	 * 1) RSB underflow
+	 *
+	 *    Some Intel parts have "bottomless RSB".  When the RSB is empty,
+	 *    speculated return targets may come from the branch predictor,
+	 *    which could have a user-poisoned BTB or BHB entry.
+	 *
+	 *    AMD has it even worse: *all* returns are speculated from the BTB,
+	 *    regardless of the state of the RSB.
+	 *
+	 *    When IBRS or eIBRS is enabled, the "user -> kernel" attack
+	 *    scenario is mitigated by the IBRS branch prediction isolation
+	 *    properties, so the RSB buffer filling wouldn't be necessary to
+	 *    protect against this type of attack.
+	 *
+	 *    The "user -> user" attack scenario is mitigated by RSB filling.
+	 *
+	 * 2) Poisoned RSB entry
+	 *
+	 *    If the 'next' in-kernel return stack is shorter than 'prev',
+	 *    'next' could be tricked into speculating with a user-poisoned RSB
+	 *    entry.
+	 *
+	 *    The "user -> kernel" attack scenario is mitigated by SMEP and
+	 *    eIBRS.
+	 *
+	 *    The "user -> user" scenario, also known as SpectreBHB, requires
+	 *    RSB clearing.
 	 *
-	 *	- RSB underflow (and switch to BTB) on Skylake+
-	 *	- SpectreRSB variant of spectre v2 on X86_BUG_SPECTRE_V2 CPUs
+	 * So to mitigate all cases, unconditionally fill RSB on context
+	 * switches.
+	 *
+	 * FIXME: Is this pointless for retbleed-affected AMD?
 	 */
 	setup_force_cpu_cap(X86_FEATURE_RSB_CTXSW);
 	pr_info("Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch\n");
 
+	spectre_v2_determine_rsb_fill_type_at_vmexit(mode);
+
 	/*
-	 * Retpoline means the kernel is safe because it has no indirect
-	 * branches. Enhanced IBRS protects firmware too, so, enable restricted
-	 * speculation around firmware calls only when Enhanced IBRS isn't
-	 * supported.
+	 * Retpoline protects the kernel, but doesn't protect firmware.  IBRS
+	 * and Enhanced IBRS protect firmware too, so enable IBRS around
+	 * firmware calls only when IBRS / Enhanced / Automatic IBRS aren't
+	 * otherwise enabled.
 	 *
 	 * Use "mode" to check Enhanced IBRS instead of boot_cpu_has(), because
 	 * the user might select retpoline on the kernel command line and if
 	 * the CPU supports Enhanced IBRS, kernel might un-intentionally not
 	 * enable IBRS around firmware calls.
 	 */
-	if (boot_cpu_has(X86_FEATURE_IBRS) && mode != SPECTRE_V2_IBRS_ENHANCED) {
+	if (boot_cpu_has_bug(X86_BUG_RETBLEED) &&
+	    boot_cpu_has(X86_FEATURE_IBPB) &&
+	    (boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
+	     boot_cpu_data.x86_vendor == X86_VENDOR_HYGON)) {
+
+		if (retbleed_cmd != RETBLEED_CMD_IBPB) {
+			setup_force_cpu_cap(X86_FEATURE_USE_IBPB_FW);
+			pr_info("Enabling Speculation Barrier for firmware calls\n");
+		}
+
+	} else if (boot_cpu_has(X86_FEATURE_IBRS) && !spectre_v2_in_ibrs_mode(mode)) {
 		setup_force_cpu_cap(X86_FEATURE_USE_IBRS_FW);
 		pr_info("Enabling Restricted Speculation for firmware calls\n");
 	}
 
 	/* Set up IBPB and STIBP depending on the general spectre V2 command */
-	spectre_v2_user_select_mitigation(cmd);
+	spectre_v2_cmd = cmd;
 }
 
 static void update_stibp_msr(void * __unused)
 {
-	wrmsrl(MSR_IA32_SPEC_CTRL, x86_spec_ctrl_base);
+	u64 val = spec_ctrl_current() | (x86_spec_ctrl_base & SPEC_CTRL_STIBP);
+	update_spec_ctrl(val);
 }
 
 /* Update x86_spec_ctrl_base in case SMT state changed. */
@@ -1039,19 +1906,26 @@
 	if (!boot_cpu_has_bug(X86_BUG_MSBDS_ONLY))
 		return;
 
-	if (sched_smt_active())
+	if (sched_smt_active()) {
 		static_branch_enable(&mds_idle_clear);
-	else
+	} else if (mmio_mitigation == MMIO_MITIGATION_OFF ||
+		   (x86_arch_cap_msr & ARCH_CAP_FBSDP_NO)) {
 		static_branch_disable(&mds_idle_clear);
+	}
 }
 
 #define MDS_MSG_SMT "MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.\n"
 #define TAA_MSG_SMT "TAA CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/tsx_async_abort.html for more details.\n"
+#define MMIO_MSG_SMT "MMIO Stale Data CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/processor_mmio_stale_data.html for more details.\n"
 
 void cpu_bugs_smt_update(void)
 {
 	mutex_lock(&spec_ctrl_mutex);
 
+	if (sched_smt_active() && unprivileged_ebpf_enabled() &&
+	    spectre_v2_enabled == SPECTRE_V2_EIBRS_LFENCE)
+		pr_warn_once(SPECTRE_V2_EIBRS_LFENCE_EBPF_SMT_MSG);
+
 	switch (spectre_v2_user_stibp) {
 	case SPECTRE_V2_USER_NONE:
 		break;
@@ -1087,6 +1961,16 @@
 		break;
 	}
 
+	switch (mmio_mitigation) {
+	case MMIO_MITIGATION_VERW:
+	case MMIO_MITIGATION_UCODE_NEEDED:
+		if (sched_smt_active())
+			pr_warn_once(MMIO_MSG_SMT);
+		break;
+	case MMIO_MITIGATION_OFF:
+		break;
+	}
+
 	mutex_unlock(&spec_ctrl_mutex);
 }
 
@@ -1191,16 +2075,6 @@
 	}
 
 	/*
-	 * If SSBD is controlled by the SPEC_CTRL MSR, then set the proper
-	 * bit in the mask to allow guests to use the mitigation even in the
-	 * case where the host does not enable it.
-	 */
-	if (static_cpu_has(X86_FEATURE_SPEC_CTRL_SSBD) ||
-	    static_cpu_has(X86_FEATURE_AMD_SSBD)) {
-		x86_spec_ctrl_mask |= SPEC_CTRL_SSBD;
-	}
-
-	/*
 	 * We have three CPU feature flags that are in play here:
 	 *  - X86_BUG_SPEC_STORE_BYPASS - CPU is susceptible.
 	 *  - X86_FEATURE_SSBD - CPU is able to turn off speculative store bypass
@@ -1217,7 +2091,7 @@
 			x86_amd_ssb_disable();
 		} else {
 			x86_spec_ctrl_base |= SPEC_CTRL_SSBD;
-			wrmsrl(MSR_IA32_SPEC_CTRL, x86_spec_ctrl_base);
+			update_spec_ctrl(x86_spec_ctrl_base);
 		}
 	}
 
@@ -1364,6 +2238,8 @@
 		if (ctrl == PR_SPEC_FORCE_DISABLE)
 			task_set_spec_ib_force_disable(task);
 		task_update_spec_tif(task);
+		if (task == current)
+			indirect_branch_prediction_barrier();
 		break;
 	default:
 		return -ERANGE;
@@ -1468,7 +2344,7 @@
 void x86_spec_ctrl_setup_ap(void)
 {
 	if (boot_cpu_has(X86_FEATURE_MSR_SPEC_CTRL))
-		wrmsrl(MSR_IA32_SPEC_CTRL, x86_spec_ctrl_base);
+		update_spec_ctrl(x86_spec_ctrl_base);
 
 	if (ssb_mode == SPEC_STORE_BYPASS_DISABLE)
 		x86_amd_ssb_disable();
@@ -1600,6 +2476,193 @@
 early_param("l1tf", l1tf_cmdline);
 
 #undef pr_fmt
+#define pr_fmt(fmt)	"Speculative Return Stack Overflow: " fmt
+
+enum srso_mitigation {
+	SRSO_MITIGATION_NONE,
+	SRSO_MITIGATION_MICROCODE,
+	SRSO_MITIGATION_SAFE_RET,
+	SRSO_MITIGATION_IBPB,
+	SRSO_MITIGATION_IBPB_ON_VMEXIT,
+};
+
+enum srso_mitigation_cmd {
+	SRSO_CMD_OFF,
+	SRSO_CMD_MICROCODE,
+	SRSO_CMD_SAFE_RET,
+	SRSO_CMD_IBPB,
+	SRSO_CMD_IBPB_ON_VMEXIT,
+};
+
+static const char * const srso_strings[] = {
+	[SRSO_MITIGATION_NONE]           = "Vulnerable",
+	[SRSO_MITIGATION_MICROCODE]      = "Mitigation: microcode",
+	[SRSO_MITIGATION_SAFE_RET]	 = "Mitigation: safe RET",
+	[SRSO_MITIGATION_IBPB]		 = "Mitigation: IBPB",
+	[SRSO_MITIGATION_IBPB_ON_VMEXIT] = "Mitigation: IBPB on VMEXIT only"
+};
+
+static enum srso_mitigation srso_mitigation __ro_after_init = SRSO_MITIGATION_NONE;
+static enum srso_mitigation_cmd srso_cmd __ro_after_init = SRSO_CMD_SAFE_RET;
+
+static int __init srso_parse_cmdline(char *str)
+{
+	if (!str)
+		return -EINVAL;
+
+	if (!strcmp(str, "off"))
+		srso_cmd = SRSO_CMD_OFF;
+	else if (!strcmp(str, "microcode"))
+		srso_cmd = SRSO_CMD_MICROCODE;
+	else if (!strcmp(str, "safe-ret"))
+		srso_cmd = SRSO_CMD_SAFE_RET;
+	else if (!strcmp(str, "ibpb"))
+		srso_cmd = SRSO_CMD_IBPB;
+	else if (!strcmp(str, "ibpb-vmexit"))
+		srso_cmd = SRSO_CMD_IBPB_ON_VMEXIT;
+	else
+		pr_err("Ignoring unknown SRSO option (%s).", str);
+
+	return 0;
+}
+early_param("spec_rstack_overflow", srso_parse_cmdline);
+
+#define SRSO_NOTICE "WARNING: See https://kernel.org/doc/html/latest/admin-guide/hw-vuln/srso.html for mitigation options."
+
+static void __init srso_select_mitigation(void)
+{
+	bool has_microcode;
+
+	if (!boot_cpu_has_bug(X86_BUG_SRSO) || cpu_mitigations_off())
+		goto pred_cmd;
+
+	/*
+	 * The first check is for the kernel running as a guest in order
+	 * for guests to verify whether IBPB is a viable mitigation.
+	 */
+	has_microcode = boot_cpu_has(X86_FEATURE_IBPB_BRTYPE) || cpu_has_ibpb_brtype_microcode();
+	if (!has_microcode) {
+		pr_warn("IBPB-extending microcode not applied!\n");
+		pr_warn(SRSO_NOTICE);
+	} else {
+		/*
+		 * Enable the synthetic (even if in a real CPUID leaf)
+		 * flags for guests.
+		 */
+		setup_force_cpu_cap(X86_FEATURE_IBPB_BRTYPE);
+
+		/*
+		 * Zen1/2 with SMT off aren't vulnerable after the right
+		 * IBPB microcode has been applied.
+		 */
+		if (boot_cpu_data.x86 < 0x19 && !cpu_smt_possible()) {
+			setup_force_cpu_cap(X86_FEATURE_SRSO_NO);
+			return;
+		}
+	}
+
+	if (retbleed_mitigation == RETBLEED_MITIGATION_IBPB) {
+		if (has_microcode) {
+			pr_err("Retbleed IBPB mitigation enabled, using same for SRSO\n");
+			srso_mitigation = SRSO_MITIGATION_IBPB;
+			goto pred_cmd;
+		}
+	}
+
+	switch (srso_cmd) {
+	case SRSO_CMD_OFF:
+		goto pred_cmd;
+
+	case SRSO_CMD_MICROCODE:
+		if (has_microcode) {
+			srso_mitigation = SRSO_MITIGATION_MICROCODE;
+			pr_warn(SRSO_NOTICE);
+		}
+		break;
+
+	case SRSO_CMD_SAFE_RET:
+		if (IS_ENABLED(CONFIG_CPU_SRSO)) {
+			/*
+			 * Enable the return thunk for generated code
+			 * like ftrace, static_call, etc.
+			 */
+			setup_force_cpu_cap(X86_FEATURE_RETHUNK);
+			setup_force_cpu_cap(X86_FEATURE_UNRET);
+
+			if (boot_cpu_data.x86 == 0x19) {
+				setup_force_cpu_cap(X86_FEATURE_SRSO_ALIAS);
+				x86_return_thunk = srso_alias_return_thunk;
+			} else {
+				setup_force_cpu_cap(X86_FEATURE_SRSO);
+				x86_return_thunk = srso_return_thunk;
+			}
+			srso_mitigation = SRSO_MITIGATION_SAFE_RET;
+		} else {
+			pr_err("WARNING: kernel not compiled with CPU_SRSO.\n");
+			goto pred_cmd;
+		}
+		break;
+
+	case SRSO_CMD_IBPB:
+		if (IS_ENABLED(CONFIG_CPU_IBPB_ENTRY)) {
+			if (has_microcode) {
+				setup_force_cpu_cap(X86_FEATURE_ENTRY_IBPB);
+				setup_force_cpu_cap(X86_FEATURE_IBPB_ON_VMEXIT);
+				srso_mitigation = SRSO_MITIGATION_IBPB;
+
+				/*
+				 * IBPB on entry already obviates the need for
+				 * software-based untraining so clear those in case some
+				 * other mitigation like Retbleed has selected them.
+				 */
+				setup_clear_cpu_cap(X86_FEATURE_UNRET);
+				setup_clear_cpu_cap(X86_FEATURE_RETHUNK);
+
+				/*
+				 * There is no need for RSB filling: entry_ibpb() ensures
+				 * all predictions, including the RSB, are invalidated,
+				 * regardless of IBPB implementation.
+				 */
+				setup_clear_cpu_cap(X86_FEATURE_RSB_VMEXIT);
+			}
+		} else {
+			pr_err("WARNING: kernel not compiled with CPU_IBPB_ENTRY.\n");
+			goto pred_cmd;
+		}
+		break;
+
+	case SRSO_CMD_IBPB_ON_VMEXIT:
+		if (IS_ENABLED(CONFIG_CPU_IBPB_ENTRY)) {
+			if (has_microcode) {
+				setup_force_cpu_cap(X86_FEATURE_IBPB_ON_VMEXIT);
+				srso_mitigation = SRSO_MITIGATION_IBPB_ON_VMEXIT;
+
+				/*
+				 * There is no need for RSB filling: entry_ibpb() ensures
+				 * all predictions, including the RSB, are invalidated,
+				 * regardless of IBPB implementation.
+				 */
+				setup_clear_cpu_cap(X86_FEATURE_RSB_VMEXIT);
+			}
+		} else {
+			pr_err("WARNING: kernel not compiled with CPU_IBPB_ENTRY.\n");
+			goto pred_cmd;
+		}
+		break;
+
+	default:
+		break;
+	}
+
+	pr_info("%s%s\n", srso_strings[srso_mitigation], (has_microcode ? "" : ", no microcode"));
+
+pred_cmd:
+	if ((!boot_cpu_has_bug(X86_BUG_SRSO) || srso_cmd == SRSO_CMD_OFF) &&
+	     boot_cpu_has(X86_FEATURE_SBPB))
+		x86_pred_cmd = PRED_CMD_SBPB;
+}
+
+#undef pr_fmt
 #define pr_fmt(fmt) fmt
 
 #ifdef CONFIG_SYSFS
@@ -1619,92 +2682,115 @@
 static ssize_t l1tf_show_state(char *buf)
 {
 	if (l1tf_vmx_mitigation == VMENTER_L1D_FLUSH_AUTO)
-		return sprintf(buf, "%s\n", L1TF_DEFAULT_MSG);
+		return sysfs_emit(buf, "%s\n", L1TF_DEFAULT_MSG);
 
 	if (l1tf_vmx_mitigation == VMENTER_L1D_FLUSH_EPT_DISABLED ||
 	    (l1tf_vmx_mitigation == VMENTER_L1D_FLUSH_NEVER &&
 	     sched_smt_active())) {
-		return sprintf(buf, "%s; VMX: %s\n", L1TF_DEFAULT_MSG,
-			       l1tf_vmx_states[l1tf_vmx_mitigation]);
+		return sysfs_emit(buf, "%s; VMX: %s\n", L1TF_DEFAULT_MSG,
+				  l1tf_vmx_states[l1tf_vmx_mitigation]);
 	}
 
-	return sprintf(buf, "%s; VMX: %s, SMT %s\n", L1TF_DEFAULT_MSG,
-		       l1tf_vmx_states[l1tf_vmx_mitigation],
-		       sched_smt_active() ? "vulnerable" : "disabled");
+	return sysfs_emit(buf, "%s; VMX: %s, SMT %s\n", L1TF_DEFAULT_MSG,
+			  l1tf_vmx_states[l1tf_vmx_mitigation],
+			  sched_smt_active() ? "vulnerable" : "disabled");
 }
 
 static ssize_t itlb_multihit_show_state(char *buf)
 {
 	if (!boot_cpu_has(X86_FEATURE_MSR_IA32_FEAT_CTL) ||
 	    !boot_cpu_has(X86_FEATURE_VMX))
-		return sprintf(buf, "KVM: Mitigation: VMX unsupported\n");
+		return sysfs_emit(buf, "KVM: Mitigation: VMX unsupported\n");
 	else if (!(cr4_read_shadow() & X86_CR4_VMXE))
-		return sprintf(buf, "KVM: Mitigation: VMX disabled\n");
+		return sysfs_emit(buf, "KVM: Mitigation: VMX disabled\n");
 	else if (itlb_multihit_kvm_mitigation)
-		return sprintf(buf, "KVM: Mitigation: Split huge pages\n");
+		return sysfs_emit(buf, "KVM: Mitigation: Split huge pages\n");
 	else
-		return sprintf(buf, "KVM: Vulnerable\n");
+		return sysfs_emit(buf, "KVM: Vulnerable\n");
 }
 #else
 static ssize_t l1tf_show_state(char *buf)
 {
-	return sprintf(buf, "%s\n", L1TF_DEFAULT_MSG);
+	return sysfs_emit(buf, "%s\n", L1TF_DEFAULT_MSG);
 }
 
 static ssize_t itlb_multihit_show_state(char *buf)
 {
-	return sprintf(buf, "Processor vulnerable\n");
+	return sysfs_emit(buf, "Processor vulnerable\n");
 }
 #endif
 
 static ssize_t mds_show_state(char *buf)
 {
 	if (boot_cpu_has(X86_FEATURE_HYPERVISOR)) {
-		return sprintf(buf, "%s; SMT Host state unknown\n",
-			       mds_strings[mds_mitigation]);
+		return sysfs_emit(buf, "%s; SMT Host state unknown\n",
+				  mds_strings[mds_mitigation]);
 	}
 
 	if (boot_cpu_has(X86_BUG_MSBDS_ONLY)) {
-		return sprintf(buf, "%s; SMT %s\n", mds_strings[mds_mitigation],
-			       (mds_mitigation == MDS_MITIGATION_OFF ? "vulnerable" :
-			        sched_smt_active() ? "mitigated" : "disabled"));
+		return sysfs_emit(buf, "%s; SMT %s\n", mds_strings[mds_mitigation],
+				  (mds_mitigation == MDS_MITIGATION_OFF ? "vulnerable" :
+				   sched_smt_active() ? "mitigated" : "disabled"));
 	}
 
-	return sprintf(buf, "%s; SMT %s\n", mds_strings[mds_mitigation],
-		       sched_smt_active() ? "vulnerable" : "disabled");
+	return sysfs_emit(buf, "%s; SMT %s\n", mds_strings[mds_mitigation],
+			  sched_smt_active() ? "vulnerable" : "disabled");
 }
 
 static ssize_t tsx_async_abort_show_state(char *buf)
 {
 	if ((taa_mitigation == TAA_MITIGATION_TSX_DISABLED) ||
 	    (taa_mitigation == TAA_MITIGATION_OFF))
-		return sprintf(buf, "%s\n", taa_strings[taa_mitigation]);
+		return sysfs_emit(buf, "%s\n", taa_strings[taa_mitigation]);
+
+	if (boot_cpu_has(X86_FEATURE_HYPERVISOR)) {
+		return sysfs_emit(buf, "%s; SMT Host state unknown\n",
+				  taa_strings[taa_mitigation]);
+	}
+
+	return sysfs_emit(buf, "%s; SMT %s\n", taa_strings[taa_mitigation],
+			  sched_smt_active() ? "vulnerable" : "disabled");
+}
+
+static ssize_t mmio_stale_data_show_state(char *buf)
+{
+	if (boot_cpu_has_bug(X86_BUG_MMIO_UNKNOWN))
+		return sysfs_emit(buf, "Unknown: No mitigations\n");
+
+	if (mmio_mitigation == MMIO_MITIGATION_OFF)
+		return sysfs_emit(buf, "%s\n", mmio_strings[mmio_mitigation]);
 
 	if (boot_cpu_has(X86_FEATURE_HYPERVISOR)) {
-		return sprintf(buf, "%s; SMT Host state unknown\n",
-			       taa_strings[taa_mitigation]);
+		return sysfs_emit(buf, "%s; SMT Host state unknown\n",
+				  mmio_strings[mmio_mitigation]);
 	}
 
-	return sprintf(buf, "%s; SMT %s\n", taa_strings[taa_mitigation],
-		       sched_smt_active() ? "vulnerable" : "disabled");
+	return sysfs_emit(buf, "%s; SMT %s\n", mmio_strings[mmio_mitigation],
+			  sched_smt_active() ? "vulnerable" : "disabled");
+}
+
+static ssize_t rfds_show_state(char *buf)
+{
+	return sysfs_emit(buf, "%s\n", rfds_strings[rfds_mitigation]);
 }
 
 static char *stibp_state(void)
 {
-	if (spectre_v2_enabled == SPECTRE_V2_IBRS_ENHANCED)
+	if (spectre_v2_in_eibrs_mode(spectre_v2_enabled) &&
+	    !boot_cpu_has(X86_FEATURE_AUTOIBRS))
 		return "";
 
 	switch (spectre_v2_user_stibp) {
 	case SPECTRE_V2_USER_NONE:
-		return ", STIBP: disabled";
+		return "; STIBP: disabled";
 	case SPECTRE_V2_USER_STRICT:
-		return ", STIBP: forced";
+		return "; STIBP: forced";
 	case SPECTRE_V2_USER_STRICT_PREFERRED:
-		return ", STIBP: always-on";
+		return "; STIBP: always-on";
 	case SPECTRE_V2_USER_PRCTL:
 	case SPECTRE_V2_USER_SECCOMP:
 		if (static_key_enabled(&switch_to_cond_stibp))
-			return ", STIBP: conditional";
+			return "; STIBP: conditional";
 	}
 	return "";
 }
@@ -1713,48 +2799,131 @@
 {
 	if (boot_cpu_has(X86_FEATURE_IBPB)) {
 		if (static_key_enabled(&switch_mm_always_ibpb))
-			return ", IBPB: always-on";
+			return "; IBPB: always-on";
 		if (static_key_enabled(&switch_mm_cond_ibpb))
-			return ", IBPB: conditional";
-		return ", IBPB: disabled";
+			return "; IBPB: conditional";
+		return "; IBPB: disabled";
 	}
 	return "";
 }
 
+static char *pbrsb_eibrs_state(void)
+{
+	if (boot_cpu_has_bug(X86_BUG_EIBRS_PBRSB)) {
+		if (boot_cpu_has(X86_FEATURE_RSB_VMEXIT_LITE) ||
+		    boot_cpu_has(X86_FEATURE_RSB_VMEXIT))
+			return "; PBRSB-eIBRS: SW sequence";
+		else
+			return "; PBRSB-eIBRS: Vulnerable";
+	} else {
+		return "; PBRSB-eIBRS: Not affected";
+	}
+}
+
+static const char *spectre_bhi_state(void)
+{
+	if (!boot_cpu_has_bug(X86_BUG_BHI))
+		return "; BHI: Not affected";
+	else if (boot_cpu_has(X86_FEATURE_CLEAR_BHB_HW))
+		return "; BHI: BHI_DIS_S";
+	else if (boot_cpu_has(X86_FEATURE_CLEAR_BHB_LOOP))
+		return "; BHI: SW loop, KVM: SW loop";
+	else if (boot_cpu_has(X86_FEATURE_RETPOLINE) &&
+		 !boot_cpu_has(X86_FEATURE_RETPOLINE_LFENCE) &&
+		 rrsba_disabled)
+		return "; BHI: Retpoline";
+	else if (boot_cpu_has(X86_FEATURE_CLEAR_BHB_LOOP_ON_VMEXIT))
+		return "; BHI: Vulnerable, KVM: SW loop";
+
+	return "; BHI: Vulnerable";
+}
+
+static ssize_t spectre_v2_show_state(char *buf)
+{
+	if (spectre_v2_enabled == SPECTRE_V2_LFENCE)
+		return sysfs_emit(buf, "Vulnerable: LFENCE\n");
+
+	if (spectre_v2_enabled == SPECTRE_V2_EIBRS && unprivileged_ebpf_enabled())
+		return sysfs_emit(buf, "Vulnerable: eIBRS with unprivileged eBPF\n");
+
+	if (sched_smt_active() && unprivileged_ebpf_enabled() &&
+	    spectre_v2_enabled == SPECTRE_V2_EIBRS_LFENCE)
+		return sysfs_emit(buf, "Vulnerable: eIBRS+LFENCE with unprivileged eBPF and SMT\n");
+
+	return sysfs_emit(buf, "%s%s%s%s%s%s%s%s\n",
+			  spectre_v2_strings[spectre_v2_enabled],
+			  ibpb_state(),
+			  boot_cpu_has(X86_FEATURE_USE_IBRS_FW) ? "; IBRS_FW" : "",
+			  stibp_state(),
+			  boot_cpu_has(X86_FEATURE_RSB_CTXSW) ? "; RSB filling" : "",
+			  pbrsb_eibrs_state(),
+			  spectre_bhi_state(),
+			  /* this should always be at the end */
+			  spectre_v2_module_string());
+}
+
 static ssize_t srbds_show_state(char *buf)
 {
-	return sprintf(buf, "%s\n", srbds_strings[srbds_mitigation]);
+	return sysfs_emit(buf, "%s\n", srbds_strings[srbds_mitigation]);
+}
+
+static ssize_t retbleed_show_state(char *buf)
+{
+	if (retbleed_mitigation == RETBLEED_MITIGATION_UNRET ||
+	    retbleed_mitigation == RETBLEED_MITIGATION_IBPB) {
+		if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD &&
+		    boot_cpu_data.x86_vendor != X86_VENDOR_HYGON)
+			return sysfs_emit(buf, "Vulnerable: untrained return thunk / IBPB on non-AMD based uarch\n");
+
+		return sysfs_emit(buf, "%s; SMT %s\n", retbleed_strings[retbleed_mitigation],
+				  !sched_smt_active() ? "disabled" :
+				  spectre_v2_user_stibp == SPECTRE_V2_USER_STRICT ||
+				  spectre_v2_user_stibp == SPECTRE_V2_USER_STRICT_PREFERRED ?
+				  "enabled with STIBP protection" : "vulnerable");
+	}
+
+	return sysfs_emit(buf, "%s\n", retbleed_strings[retbleed_mitigation]);
+}
+
+static ssize_t gds_show_state(char *buf)
+{
+	return sysfs_emit(buf, "%s\n", gds_strings[gds_mitigation]);
+}
+
+static ssize_t srso_show_state(char *buf)
+{
+	if (boot_cpu_has(X86_FEATURE_SRSO_NO))
+		return sysfs_emit(buf, "Mitigation: SMT disabled\n");
+
+	return sysfs_emit(buf, "%s%s\n",
+			  srso_strings[srso_mitigation],
+			  boot_cpu_has(X86_FEATURE_IBPB_BRTYPE) ? "" : ", no microcode");
 }
 
 static ssize_t cpu_show_common(struct device *dev, struct device_attribute *attr,
 			       char *buf, unsigned int bug)
 {
 	if (!boot_cpu_has_bug(bug))
-		return sprintf(buf, "Not affected\n");
+		return sysfs_emit(buf, "Not affected\n");
 
 	switch (bug) {
 	case X86_BUG_CPU_MELTDOWN:
 		if (boot_cpu_has(X86_FEATURE_PTI))
-			return sprintf(buf, "Mitigation: PTI\n");
+			return sysfs_emit(buf, "Mitigation: PTI\n");
 
 		if (hypervisor_is_type(X86_HYPER_XEN_PV))
-			return sprintf(buf, "Unknown (XEN PV detected, hypervisor mitigation required)\n");
+			return sysfs_emit(buf, "Unknown (XEN PV detected, hypervisor mitigation required)\n");
 
 		break;
 
 	case X86_BUG_SPECTRE_V1:
-		return sprintf(buf, "%s\n", spectre_v1_strings[spectre_v1_mitigation]);
+		return sysfs_emit(buf, "%s\n", spectre_v1_strings[spectre_v1_mitigation]);
 
 	case X86_BUG_SPECTRE_V2:
-		return sprintf(buf, "%s%s%s%s%s%s\n", spectre_v2_strings[spectre_v2_enabled],
-			       ibpb_state(),
-			       boot_cpu_has(X86_FEATURE_USE_IBRS_FW) ? ", IBRS_FW" : "",
-			       stibp_state(),
-			       boot_cpu_has(X86_FEATURE_RSB_CTXSW) ? ", RSB filling" : "",
-			       spectre_v2_module_string());
+		return spectre_v2_show_state(buf);
 
 	case X86_BUG_SPEC_STORE_BYPASS:
-		return sprintf(buf, "%s\n", ssb_strings[ssb_mode]);
+		return sysfs_emit(buf, "%s\n", ssb_strings[ssb_mode]);
 
 	case X86_BUG_L1TF:
 		if (boot_cpu_has(X86_FEATURE_L1TF_PTEINV))
@@ -1773,11 +2942,27 @@
 	case X86_BUG_SRBDS:
 		return srbds_show_state(buf);
 
+	case X86_BUG_MMIO_STALE_DATA:
+	case X86_BUG_MMIO_UNKNOWN:
+		return mmio_stale_data_show_state(buf);
+
+	case X86_BUG_RETBLEED:
+		return retbleed_show_state(buf);
+
+	case X86_BUG_GDS:
+		return gds_show_state(buf);
+
+	case X86_BUG_SRSO:
+		return srso_show_state(buf);
+
+	case X86_BUG_RFDS:
+		return rfds_show_state(buf);
+
 	default:
 		break;
 	}
 
-	return sprintf(buf, "Vulnerable\n");
+	return sysfs_emit(buf, "Vulnerable\n");
 }
 
 ssize_t cpu_show_meltdown(struct device *dev, struct device_attribute *attr, char *buf)
@@ -1824,4 +3009,32 @@
 {
 	return cpu_show_common(dev, attr, buf, X86_BUG_SRBDS);
 }
+
+ssize_t cpu_show_mmio_stale_data(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	if (boot_cpu_has_bug(X86_BUG_MMIO_UNKNOWN))
+		return cpu_show_common(dev, attr, buf, X86_BUG_MMIO_UNKNOWN);
+	else
+		return cpu_show_common(dev, attr, buf, X86_BUG_MMIO_STALE_DATA);
+}
+
+ssize_t cpu_show_retbleed(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return cpu_show_common(dev, attr, buf, X86_BUG_RETBLEED);
+}
+
+ssize_t cpu_show_gds(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return cpu_show_common(dev, attr, buf, X86_BUG_GDS);
+}
+
+ssize_t cpu_show_spec_rstack_overflow(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return cpu_show_common(dev, attr, buf, X86_BUG_SRSO);
+}
+
+ssize_t cpu_show_reg_file_data_sampling(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return cpu_show_common(dev, attr, buf, X86_BUG_RFDS);
+}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/cacheinfo.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/cacheinfo.c
@@ -795,7 +795,7 @@
 			cpuid(2, &regs[0], &regs[1], &regs[2], &regs[3]);
 
 			/* If bit 31 is set, this is an unknown format */
-			for (j = 0 ; j < 3 ; j++)
+			for (j = 0 ; j < 4 ; j++)
 				if (regs[j] & (1 << 31))
 					regs[j] = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/common.c
@@ -18,11 +18,15 @@
 #include <linux/init.h>
 #include <linux/kprobes.h>
 #include <linux/kgdb.h>
+#include <linux/mem_encrypt.h>
 #include <linux/smp.h>
+#include <linux/cpu.h>
 #include <linux/io.h>
 #include <linux/syscore_ops.h>
 #include <linux/pgtable.h>
+#include <linux/utsname.h>
 
+#include <asm/alternative.h>
 #include <asm/cmdline.h>
 #include <asm/stackprotector.h>
 #include <asm/perf_event.h>
@@ -42,7 +46,7 @@
 #include <asm/setup.h>
 #include <asm/apic.h>
 #include <asm/desc.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/mtrr.h>
 #include <asm/hwcap2.h>
 #include <linux/numa.h>
@@ -58,7 +62,7 @@
 #include <asm/intel-family.h>
 #include <asm/cpu_device_id.h>
 #include <asm/uv/uv.h>
-#include <asm/sigframe.h>
+#include <asm/set_memory.h>
 
 #include "cpu.h"
 
@@ -85,6 +89,79 @@
 }
 EXPORT_SYMBOL_GPL(get_llc_id);
 
+static struct ppin_info {
+	int	feature;
+	int	msr_ppin_ctl;
+} ppin_info[] = {
+	[X86_VENDOR_INTEL] = {
+		.feature = X86_FEATURE_INTEL_PPIN,
+		.msr_ppin_ctl = MSR_PPIN_CTL,
+	},
+	[X86_VENDOR_AMD] = {
+		.feature = X86_FEATURE_AMD_PPIN,
+		.msr_ppin_ctl = MSR_AMD_PPIN_CTL,
+	},
+};
+
+static const struct x86_cpu_id ppin_cpuids[] = {
+	X86_MATCH_FEATURE(X86_FEATURE_AMD_PPIN, &ppin_info[X86_VENDOR_AMD]),
+
+	/* Legacy models without CPUID enumeration */
+	X86_MATCH_INTEL_FAM6_MODEL(IVYBRIDGE_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(HASWELL_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(BROADWELL_D, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(BROADWELL_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(SKYLAKE_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_D, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(XEON_PHI_KNL, &ppin_info[X86_VENDOR_INTEL]),
+	X86_MATCH_INTEL_FAM6_MODEL(XEON_PHI_KNM, &ppin_info[X86_VENDOR_INTEL]),
+
+	{}
+};
+
+static void ppin_init(struct cpuinfo_x86 *c)
+{
+	const struct x86_cpu_id *id;
+	unsigned long long val;
+	struct ppin_info *info;
+
+	id = x86_match_cpu(ppin_cpuids);
+	if (!id)
+		return;
+
+	/*
+	 * Testing the presence of the MSR is not enough. Need to check
+	 * that the PPIN_CTL allows reading of the PPIN.
+	 */
+	info = (struct ppin_info *)id->driver_data;
+
+	if (rdmsrl_safe(info->msr_ppin_ctl, &val))
+		goto clear_ppin;
+
+	if ((val & 3UL) == 1UL) {
+		/* PPIN locked in disabled mode */
+		goto clear_ppin;
+	}
+
+	/* If PPIN is disabled, try to enable */
+	if (!(val & 2UL)) {
+		wrmsrl_safe(info->msr_ppin_ctl,  val | 2UL);
+		rdmsrl_safe(info->msr_ppin_ctl, &val);
+	}
+
+	/* Is the enable bit set? */
+	if (val & 2UL) {
+		set_cpu_cap(c, info->feature);
+		return;
+	}
+
+clear_ppin:
+	clear_cpu_cap(c, info->feature);
+}
+
 /* correctly size the local cpu masks */
 void __init setup_cpu_local_masks(void)
 {
@@ -794,7 +871,7 @@
 #endif
 }
 
-static void get_cpu_vendor(struct cpuinfo_x86 *c)
+void get_cpu_vendor(struct cpuinfo_x86 *c)
 {
 	char *v = c->x86_vendor_id;
 	int i;
@@ -964,6 +1041,9 @@
 	if (c->extended_cpuid_level >= 0x8000001f)
 		c->x86_capability[CPUID_8000_001F_EAX] = cpuid_eax(0x8000001f);
 
+	if (c->extended_cpuid_level >= 0x80000021)
+		c->x86_capability[CPUID_8000_0021_EAX] = cpuid_eax(0x80000021);
+
 	init_scattered_cpuid_features(c);
 	init_speculation_control(c);
 
@@ -1027,6 +1107,9 @@
 #define NO_SWAPGS		BIT(6)
 #define NO_ITLB_MULTIHIT	BIT(7)
 #define NO_SPECTRE_V2		BIT(8)
+#define NO_MMIO			BIT(9)
+#define NO_EIBRS_PBRSB		BIT(10)
+#define NO_BHI			BIT(11)
 
 #define VULNWL(vendor, family, model, whitelist)	\
 	X86_MATCH_VENDOR_FAM_MODEL(vendor, family, model, whitelist)
@@ -1047,6 +1130,11 @@
 	VULNWL(NSC,	5, X86_MODEL_ANY,	NO_SPECULATION),
 
 	/* Intel Family 6 */
+	VULNWL_INTEL(TIGERLAKE,			NO_MMIO),
+	VULNWL_INTEL(TIGERLAKE_L,		NO_MMIO),
+	VULNWL_INTEL(ALDERLAKE,			NO_MMIO),
+	VULNWL_INTEL(ALDERLAKE_L,		NO_MMIO),
+
 	VULNWL_INTEL(ATOM_SALTWELL,		NO_SPECULATION | NO_ITLB_MULTIHIT),
 	VULNWL_INTEL(ATOM_SALTWELL_TABLET,	NO_SPECULATION | NO_ITLB_MULTIHIT),
 	VULNWL_INTEL(ATOM_SALTWELL_MID,		NO_SPECULATION | NO_ITLB_MULTIHIT),
@@ -1065,9 +1153,9 @@
 	VULNWL_INTEL(ATOM_AIRMONT_MID,		NO_L1TF | MSBDS_ONLY | NO_SWAPGS | NO_ITLB_MULTIHIT),
 	VULNWL_INTEL(ATOM_AIRMONT_NP,		NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT),
 
-	VULNWL_INTEL(ATOM_GOLDMONT,		NO_MDS | NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT),
-	VULNWL_INTEL(ATOM_GOLDMONT_D,		NO_MDS | NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT),
-	VULNWL_INTEL(ATOM_GOLDMONT_PLUS,	NO_MDS | NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT),
+	VULNWL_INTEL(ATOM_GOLDMONT,		NO_MDS | NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO),
+	VULNWL_INTEL(ATOM_GOLDMONT_D,		NO_MDS | NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO),
+	VULNWL_INTEL(ATOM_GOLDMONT_PLUS,	NO_MDS | NO_L1TF | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_EIBRS_PBRSB),
 
 	/*
 	 * Technically, swapgs isn't serializing on AMD (despite it previously
@@ -1077,42 +1165,100 @@
 	 * good enough for our purposes.
 	 */
 
-	VULNWL_INTEL(ATOM_TREMONT_D,		NO_ITLB_MULTIHIT),
+	VULNWL_INTEL(ATOM_TREMONT,		NO_EIBRS_PBRSB),
+	VULNWL_INTEL(ATOM_TREMONT_L,		NO_EIBRS_PBRSB),
+	VULNWL_INTEL(ATOM_TREMONT_D,		NO_ITLB_MULTIHIT | NO_EIBRS_PBRSB),
 
 	/* AMD Family 0xf - 0x12 */
-	VULNWL_AMD(0x0f,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT),
-	VULNWL_AMD(0x10,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT),
-	VULNWL_AMD(0x11,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT),
-	VULNWL_AMD(0x12,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT),
+	VULNWL_AMD(0x0f,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_BHI),
+	VULNWL_AMD(0x10,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_BHI),
+	VULNWL_AMD(0x11,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_BHI),
+	VULNWL_AMD(0x12,	NO_MELTDOWN | NO_SSB | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_BHI),
 
 	/* FAMILY_ANY must be last, otherwise 0x0f - 0x12 matches won't work */
-	VULNWL_AMD(X86_FAMILY_ANY,	NO_MELTDOWN | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT),
-	VULNWL_HYGON(X86_FAMILY_ANY,	NO_MELTDOWN | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT),
+	VULNWL_AMD(X86_FAMILY_ANY,	NO_MELTDOWN | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_BHI | NO_EIBRS_PBRSB),
+	VULNWL_HYGON(X86_FAMILY_ANY,	NO_MELTDOWN | NO_L1TF | NO_MDS | NO_SWAPGS | NO_ITLB_MULTIHIT | NO_MMIO | NO_BHI | NO_EIBRS_PBRSB),
 
 	/* Zhaoxin Family 7 */
-	VULNWL(CENTAUR,	7, X86_MODEL_ANY,	NO_SPECTRE_V2 | NO_SWAPGS),
-	VULNWL(ZHAOXIN,	7, X86_MODEL_ANY,	NO_SPECTRE_V2 | NO_SWAPGS),
+	VULNWL(CENTAUR,	7, X86_MODEL_ANY,	NO_SPECTRE_V2 | NO_SWAPGS | NO_MMIO | NO_BHI),
+	VULNWL(ZHAOXIN,	7, X86_MODEL_ANY,	NO_SPECTRE_V2 | NO_SWAPGS | NO_MMIO | NO_BHI),
 	{}
 };
 
+#define VULNBL(vendor, family, model, blacklist)	\
+	X86_MATCH_VENDOR_FAM_MODEL(vendor, family, model, blacklist)
+
 #define VULNBL_INTEL_STEPPINGS(model, steppings, issues)		   \
 	X86_MATCH_VENDOR_FAM_MODEL_STEPPINGS_FEATURE(INTEL, 6,		   \
 					    INTEL_FAM6_##model, steppings, \
 					    X86_FEATURE_ANY, issues)
 
+#define VULNBL_AMD(family, blacklist)		\
+	VULNBL(AMD, family, X86_MODEL_ANY, blacklist)
+
+#define VULNBL_HYGON(family, blacklist)		\
+	VULNBL(HYGON, family, X86_MODEL_ANY, blacklist)
+
 #define SRBDS		BIT(0)
+/* CPU is affected by X86_BUG_MMIO_STALE_DATA */
+#define MMIO		BIT(1)
+/* CPU is affected by Shared Buffers Data Sampling (SBDS), a variant of X86_BUG_MMIO_STALE_DATA */
+#define MMIO_SBDS	BIT(2)
+/* CPU is affected by RETbleed, speculating where you would not expect it */
+#define RETBLEED	BIT(3)
+/* CPU is affected by SMT (cross-thread) return predictions */
+#define SMT_RSB		BIT(4)
+/* CPU is affected by SRSO */
+#define SRSO		BIT(5)
+/* CPU is affected by GDS */
+#define GDS		BIT(6)
+/* CPU is affected by Register File Data Sampling */
+#define RFDS		BIT(7)
 
 static const struct x86_cpu_id cpu_vuln_blacklist[] __initconst = {
 	VULNBL_INTEL_STEPPINGS(IVYBRIDGE,	X86_STEPPING_ANY,		SRBDS),
 	VULNBL_INTEL_STEPPINGS(HASWELL,		X86_STEPPING_ANY,		SRBDS),
 	VULNBL_INTEL_STEPPINGS(HASWELL_L,	X86_STEPPING_ANY,		SRBDS),
 	VULNBL_INTEL_STEPPINGS(HASWELL_G,	X86_STEPPING_ANY,		SRBDS),
+	VULNBL_INTEL_STEPPINGS(HASWELL_X,	X86_STEPPING_ANY,		MMIO),
+	VULNBL_INTEL_STEPPINGS(BROADWELL_D,	X86_STEPPING_ANY,		MMIO),
 	VULNBL_INTEL_STEPPINGS(BROADWELL_G,	X86_STEPPING_ANY,		SRBDS),
+	VULNBL_INTEL_STEPPINGS(BROADWELL_X,	X86_STEPPING_ANY,		MMIO),
 	VULNBL_INTEL_STEPPINGS(BROADWELL,	X86_STEPPING_ANY,		SRBDS),
-	VULNBL_INTEL_STEPPINGS(SKYLAKE_L,	X86_STEPPING_ANY,		SRBDS),
-	VULNBL_INTEL_STEPPINGS(SKYLAKE,		X86_STEPPING_ANY,		SRBDS),
-	VULNBL_INTEL_STEPPINGS(KABYLAKE_L,	X86_STEPPINGS(0x0, 0xC),	SRBDS),
-	VULNBL_INTEL_STEPPINGS(KABYLAKE,	X86_STEPPINGS(0x0, 0xD),	SRBDS),
+	VULNBL_INTEL_STEPPINGS(SKYLAKE_X,	X86_STEPPING_ANY,		MMIO | RETBLEED | GDS),
+	VULNBL_INTEL_STEPPINGS(SKYLAKE_L,	X86_STEPPING_ANY,		MMIO | RETBLEED | GDS | SRBDS),
+	VULNBL_INTEL_STEPPINGS(SKYLAKE,		X86_STEPPING_ANY,		MMIO | RETBLEED | GDS | SRBDS),
+	VULNBL_INTEL_STEPPINGS(KABYLAKE_L,	X86_STEPPING_ANY,		MMIO | RETBLEED | GDS | SRBDS),
+	VULNBL_INTEL_STEPPINGS(KABYLAKE,	X86_STEPPING_ANY,		MMIO | RETBLEED | GDS | SRBDS),
+	VULNBL_INTEL_STEPPINGS(CANNONLAKE_L,	X86_STEPPING_ANY,		RETBLEED),
+	VULNBL_INTEL_STEPPINGS(ICELAKE_L,	X86_STEPPING_ANY,		MMIO | MMIO_SBDS | RETBLEED | GDS),
+	VULNBL_INTEL_STEPPINGS(ICELAKE_D,	X86_STEPPING_ANY,		MMIO | GDS),
+	VULNBL_INTEL_STEPPINGS(ICELAKE_X,	X86_STEPPING_ANY,		MMIO | GDS),
+	VULNBL_INTEL_STEPPINGS(COMETLAKE,	X86_STEPPING_ANY,		MMIO | MMIO_SBDS | RETBLEED | GDS),
+	VULNBL_INTEL_STEPPINGS(COMETLAKE_L,	X86_STEPPINGS(0x0, 0x0),	MMIO | RETBLEED),
+	VULNBL_INTEL_STEPPINGS(COMETLAKE_L,	X86_STEPPING_ANY,		MMIO | MMIO_SBDS | RETBLEED | GDS),
+	VULNBL_INTEL_STEPPINGS(TIGERLAKE_L,	X86_STEPPING_ANY,		GDS),
+	VULNBL_INTEL_STEPPINGS(TIGERLAKE,	X86_STEPPING_ANY,		GDS),
+	VULNBL_INTEL_STEPPINGS(LAKEFIELD,	X86_STEPPING_ANY,		MMIO | MMIO_SBDS | RETBLEED),
+	VULNBL_INTEL_STEPPINGS(ROCKETLAKE,	X86_STEPPING_ANY,		MMIO | RETBLEED | GDS),
+	VULNBL_INTEL_STEPPINGS(ALDERLAKE,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(ALDERLAKE_L,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(RAPTORLAKE,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(RAPTORLAKE_P,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(RAPTORLAKE_S,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(ALDERLAKE_N,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(ATOM_TREMONT,	X86_STEPPING_ANY,		MMIO | MMIO_SBDS | RFDS),
+	VULNBL_INTEL_STEPPINGS(ATOM_TREMONT_D,	X86_STEPPING_ANY,		MMIO | RFDS),
+	VULNBL_INTEL_STEPPINGS(ATOM_TREMONT_L,	X86_STEPPING_ANY,		MMIO | MMIO_SBDS | RFDS),
+	VULNBL_INTEL_STEPPINGS(ATOM_GOLDMONT,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(ATOM_GOLDMONT_D,	X86_STEPPING_ANY,		RFDS),
+	VULNBL_INTEL_STEPPINGS(ATOM_GOLDMONT_PLUS, X86_STEPPING_ANY,		RFDS),
+
+	VULNBL_AMD(0x15, RETBLEED),
+	VULNBL_AMD(0x16, RETBLEED),
+	VULNBL_AMD(0x17, RETBLEED | SMT_RSB | SRSO),
+	VULNBL_HYGON(0x18, RETBLEED | SMT_RSB | SRSO),
+	VULNBL_AMD(0x19, SRSO),
 	{}
 };
 
@@ -1125,21 +1271,46 @@
 
 u64 x86_read_arch_cap_msr(void)
 {
-	u64 ia32_cap = 0;
+	u64 x86_arch_cap_msr = 0;
 
 	if (boot_cpu_has(X86_FEATURE_ARCH_CAPABILITIES))
-		rdmsrl(MSR_IA32_ARCH_CAPABILITIES, ia32_cap);
+		rdmsrl(MSR_IA32_ARCH_CAPABILITIES, x86_arch_cap_msr);
+
+	return x86_arch_cap_msr;
+}
+
+static bool arch_cap_mmio_immune(u64 x86_arch_cap_msr)
+{
+	return (x86_arch_cap_msr & ARCH_CAP_FBSDP_NO &&
+		x86_arch_cap_msr & ARCH_CAP_PSDP_NO &&
+		x86_arch_cap_msr & ARCH_CAP_SBDR_SSDP_NO);
+}
+
+static bool __init vulnerable_to_rfds(u64 x86_arch_cap_msr)
+{
+	/* The "immunity" bit trumps everything else: */
+	if (x86_arch_cap_msr & ARCH_CAP_RFDS_NO)
+		return false;
+
+	/*
+	 * VMMs set ARCH_CAP_RFDS_CLEAR for processors not in the blacklist to
+	 * indicate that mitigation is needed because guest is running on a
+	 * vulnerable hardware or may migrate to such hardware:
+	 */
+	if (x86_arch_cap_msr & ARCH_CAP_RFDS_CLEAR)
+		return true;
 
-	return ia32_cap;
+	/* Only consult the blacklist when there is no enumeration: */
+	return cpu_matches(cpu_vuln_blacklist, RFDS);
 }
 
 static void __init cpu_set_bug_bits(struct cpuinfo_x86 *c)
 {
-	u64 ia32_cap = x86_read_arch_cap_msr();
+	u64 x86_arch_cap_msr = x86_read_arch_cap_msr();
 
 	/* Set ITLB_MULTIHIT bug if cpu is not in the whitelist and not mitigated */
 	if (!cpu_matches(cpu_vuln_whitelist, NO_ITLB_MULTIHIT) &&
-	    !(ia32_cap & ARCH_CAP_PSCHANGE_MC_NO))
+	    !(x86_arch_cap_msr & ARCH_CAP_PSCHANGE_MC_NO))
 		setup_force_cpu_bug(X86_BUG_ITLB_MULTIHIT);
 
 	if (cpu_matches(cpu_vuln_whitelist, NO_SPECULATION))
@@ -1151,15 +1322,23 @@
 		setup_force_cpu_bug(X86_BUG_SPECTRE_V2);
 
 	if (!cpu_matches(cpu_vuln_whitelist, NO_SSB) &&
-	    !(ia32_cap & ARCH_CAP_SSB_NO) &&
+	    !(x86_arch_cap_msr & ARCH_CAP_SSB_NO) &&
 	   !cpu_has(c, X86_FEATURE_AMD_SSB_NO))
 		setup_force_cpu_bug(X86_BUG_SPEC_STORE_BYPASS);
 
-	if (ia32_cap & ARCH_CAP_IBRS_ALL)
+	/*
+	 * AMD's AutoIBRS is equivalent to Intel's eIBRS - use the Intel feature
+	 * flag and protect from vendor-specific bugs via the whitelist.
+	 */
+	if ((x86_arch_cap_msr & ARCH_CAP_IBRS_ALL) || cpu_has(c, X86_FEATURE_AUTOIBRS)) {
 		setup_force_cpu_cap(X86_FEATURE_IBRS_ENHANCED);
+		if (!cpu_matches(cpu_vuln_whitelist, NO_EIBRS_PBRSB) &&
+		    !(x86_arch_cap_msr & ARCH_CAP_PBRSB_NO))
+			setup_force_cpu_bug(X86_BUG_EIBRS_PBRSB);
+	}
 
 	if (!cpu_matches(cpu_vuln_whitelist, NO_MDS) &&
-	    !(ia32_cap & ARCH_CAP_MDS_NO)) {
+	    !(x86_arch_cap_msr & ARCH_CAP_MDS_NO)) {
 		setup_force_cpu_bug(X86_BUG_MDS);
 		if (cpu_matches(cpu_vuln_whitelist, MSBDS_ONLY))
 			setup_force_cpu_bug(X86_BUG_MSBDS_ONLY);
@@ -1178,25 +1357,82 @@
 	 * TSX_CTRL check alone is not sufficient for cases when the microcode
 	 * update is not present or running as guest that don't get TSX_CTRL.
 	 */
-	if (!(ia32_cap & ARCH_CAP_TAA_NO) &&
+	if (!(x86_arch_cap_msr & ARCH_CAP_TAA_NO) &&
 	    (cpu_has(c, X86_FEATURE_RTM) ||
-	     (ia32_cap & ARCH_CAP_TSX_CTRL_MSR)))
+	     (x86_arch_cap_msr & ARCH_CAP_TSX_CTRL_MSR)))
 		setup_force_cpu_bug(X86_BUG_TAA);
 
 	/*
 	 * SRBDS affects CPUs which support RDRAND or RDSEED and are listed
 	 * in the vulnerability blacklist.
+	 *
+	 * Some of the implications and mitigation of Shared Buffers Data
+	 * Sampling (SBDS) are similar to SRBDS. Give SBDS same treatment as
+	 * SRBDS.
 	 */
 	if ((cpu_has(c, X86_FEATURE_RDRAND) ||
 	     cpu_has(c, X86_FEATURE_RDSEED)) &&
-	    cpu_matches(cpu_vuln_blacklist, SRBDS))
+	    cpu_matches(cpu_vuln_blacklist, SRBDS | MMIO_SBDS))
 		    setup_force_cpu_bug(X86_BUG_SRBDS);
 
+	/*
+	 * Processor MMIO Stale Data bug enumeration
+	 *
+	 * Affected CPU list is generally enough to enumerate the vulnerability,
+	 * but for virtualization case check for ARCH_CAP MSR bits also, VMM may
+	 * not want the guest to enumerate the bug.
+	 *
+	 * Set X86_BUG_MMIO_UNKNOWN for CPUs that are neither in the blacklist,
+	 * nor in the whitelist and also don't enumerate MSR ARCH_CAP MMIO bits.
+	 */
+	if (!arch_cap_mmio_immune(x86_arch_cap_msr)) {
+		if (cpu_matches(cpu_vuln_blacklist, MMIO))
+			setup_force_cpu_bug(X86_BUG_MMIO_STALE_DATA);
+		else if (!cpu_matches(cpu_vuln_whitelist, NO_MMIO))
+			setup_force_cpu_bug(X86_BUG_MMIO_UNKNOWN);
+	}
+
+	if (!cpu_has(c, X86_FEATURE_BTC_NO)) {
+		if (cpu_matches(cpu_vuln_blacklist, RETBLEED) || (x86_arch_cap_msr & ARCH_CAP_RSBA))
+			setup_force_cpu_bug(X86_BUG_RETBLEED);
+	}
+
+	if (cpu_matches(cpu_vuln_blacklist, SMT_RSB))
+		setup_force_cpu_bug(X86_BUG_SMT_RSB);
+
+	/*
+	 * Check if CPU is vulnerable to GDS. If running in a virtual machine on
+	 * an affected processor, the VMM may have disabled the use of GATHER by
+	 * disabling AVX2. The only way to do this in HW is to clear XCR0[2],
+	 * which means that AVX will be disabled.
+	 */
+	if (cpu_matches(cpu_vuln_blacklist, GDS) && !(x86_arch_cap_msr & ARCH_CAP_GDS_NO) &&
+	    boot_cpu_has(X86_FEATURE_AVX))
+		setup_force_cpu_bug(X86_BUG_GDS);
+
+	if (!cpu_has(c, X86_FEATURE_SRSO_NO)) {
+		if (cpu_matches(cpu_vuln_blacklist, SRSO))
+			setup_force_cpu_bug(X86_BUG_SRSO);
+	}
+
+	/* When virtualized, eIBRS could be hidden, assume vulnerable */
+	if (!(x86_arch_cap_msr & ARCH_CAP_BHI_NO) &&
+	    !cpu_matches(cpu_vuln_whitelist, NO_BHI) &&
+	    (boot_cpu_has(X86_FEATURE_IBRS_ENHANCED) ||
+	     boot_cpu_has(X86_FEATURE_HYPERVISOR)))
+		setup_force_cpu_bug(X86_BUG_BHI);
+
+	if (vulnerable_to_rfds(x86_arch_cap_msr))
+		setup_force_cpu_bug(X86_BUG_RFDS);
+
+	if (cpu_has(c, X86_FEATURE_AMD_IBPB) && !cpu_has(c, X86_FEATURE_AMD_IBPB_RET))
+		setup_force_cpu_bug(X86_BUG_IBPB_NO_RET);
+
 	if (cpu_matches(cpu_vuln_whitelist, NO_MELTDOWN))
 		return;
 
 	/* Rogue Data Cache Load? No! */
-	if (ia32_cap & ARCH_CAP_RDCL_NO)
+	if (x86_arch_cap_msr & ARCH_CAP_RDCL_NO)
 		return;
 
 	setup_force_cpu_bug(X86_BUG_CPU_MELTDOWN);
@@ -1333,10 +1569,6 @@
 
 	sld_setup(c);
 
-	fpu__init_system(c);
-
-	init_sigframe_size();
-
 #ifdef CONFIG_X86_32
 	/*
 	 * Regardless of whether PCID is enumerated, the SDM says
@@ -1363,15 +1595,11 @@
 	detect_nopl();
 }
 
-void __init early_cpu_init(void)
+void __init init_cpu_devs(void)
 {
 	const struct cpu_dev *const *cdev;
 	int count = 0;
 
-#ifdef CONFIG_PROCESSOR_SELECT
-	pr_info("KERNEL supported cpus:\n");
-#endif
-
 	for (cdev = __x86_cpu_dev_start; cdev < __x86_cpu_dev_end; cdev++) {
 		const struct cpu_dev *cpudev = *cdev;
 
@@ -1379,26 +1607,35 @@
 			break;
 		cpu_devs[count] = cpudev;
 		count++;
+	}
+}
 
+void __init early_cpu_init(void)
+{
 #ifdef CONFIG_PROCESSOR_SELECT
-		{
-			unsigned int j;
+	unsigned int i, j;
 
-			for (j = 0; j < 2; j++) {
-				if (!cpudev->c_ident[j])
-					continue;
-				pr_info("  %s %s\n", cpudev->c_vendor,
-					cpudev->c_ident[j]);
-			}
-		}
+	pr_info("KERNEL supported cpus:\n");
 #endif
+
+	init_cpu_devs();
+
+#ifdef CONFIG_PROCESSOR_SELECT
+	for (i = 0; i < X86_VENDOR_NUM && cpu_devs[i]; i++) {
+		for (j = 0; j < 2; j++) {
+			if (!cpu_devs[i]->c_ident[j])
+				continue;
+			pr_info("  %s %s\n", cpu_devs[i]->c_vendor,
+				cpu_devs[i]->c_ident[j]);
+		}
 	}
+#endif
+
 	early_identify_cpu(&boot_cpu_data);
 }
 
-static void detect_null_seg_behavior(struct cpuinfo_x86 *c)
+static bool detect_null_seg_behavior(void)
 {
-#ifdef CONFIG_X86_64
 	/*
 	 * Empirically, writing zero to a segment selector on AMD does
 	 * not clear the base, whereas writing zero to a segment
@@ -1419,10 +1656,43 @@
 	wrmsrl(MSR_FS_BASE, 1);
 	loadsegment(fs, 0);
 	rdmsrl(MSR_FS_BASE, tmp);
-	if (tmp != 0)
-		set_cpu_bug(c, X86_BUG_NULL_SEG);
 	wrmsrl(MSR_FS_BASE, old_base);
-#endif
+	return tmp == 0;
+}
+
+void check_null_seg_clears_base(struct cpuinfo_x86 *c)
+{
+	/* BUG_NULL_SEG is only relevant with 64bit userspace */
+	if (!IS_ENABLED(CONFIG_X86_64))
+		return;
+
+	/* Zen3 CPUs advertise Null Selector Clears Base in CPUID. */
+	if (c->extended_cpuid_level >= 0x80000021 &&
+	    cpuid_eax(0x80000021) & BIT(6))
+		return;
+
+	/*
+	 * CPUID bit above wasn't set. If this kernel is still running
+	 * as a HV guest, then the HV has decided not to advertize
+	 * that CPUID bit for whatever reason.	For example, one
+	 * member of the migration pool might be vulnerable.  Which
+	 * means, the bug is present: set the BUG flag and return.
+	 */
+	if (cpu_has(c, X86_FEATURE_HYPERVISOR)) {
+		set_cpu_bug(c, X86_BUG_NULL_SEG);
+		return;
+	}
+
+	/*
+	 * Zen2 CPUs also have this behaviour, but no CPUID bit.
+	 * 0x18 is the respective family for Hygon.
+	 */
+	if ((c->x86 == 0x17 || c->x86 == 0x18) &&
+	    detect_null_seg_behavior())
+		return;
+
+	/* All the remaining ones are affected */
+	set_cpu_bug(c, X86_BUG_NULL_SEG);
 }
 
 static void generic_identify(struct cpuinfo_x86 *c)
@@ -1458,8 +1728,6 @@
 
 	get_model_name(c); /* Default name */
 
-	detect_null_seg_behavior(c);
-
 	/*
 	 * ESPFIX is a strange bug.  All real CPUs have it.  Paravirt
 	 * systems that run Linux at CPL > 0 may or may not have the
@@ -1544,6 +1812,13 @@
 	c->apicid = apic->phys_pkg_id(c->initial_apicid, 0);
 #endif
 
+
+	/*
+	 * Set default APIC and TSC_DEADLINE MSR fencing flag. AMD and
+	 * Hygon will clear it in ->c_init() below.
+	 */
+	set_cpu_cap(c, X86_FEATURE_APIC_MSRS_FENCE);
+
 	/*
 	 * Vendor-specific initialization.  In this section we
 	 * canonicalize the feature flags, meaning if there are
@@ -1620,6 +1895,8 @@
 			c->x86_capability[i] |= boot_cpu_data.x86_capability[i];
 	}
 
+	ppin_init(c);
+
 	/* Init Machine Check Exception if available. */
 	mcheck_cpu_init(c);
 
@@ -1684,6 +1961,10 @@
 	validate_apic_and_package_id(c);
 	x86_spec_ctrl_setup_ap();
 	update_srbds_msr();
+	if (boot_cpu_has_bug(X86_BUG_GDS))
+		update_gds_msr();
+
+	tsx_ap_init();
 }
 
 static __init int setup_noclflush(char *arg)
@@ -2009,8 +2290,6 @@
 
 	doublefault_init_cpu_tss();
 
-	fpu__init_cpu();
-
 	if (is_uv_system())
 		uv_cpu_init();
 
@@ -2026,38 +2305,58 @@
 	 */
 	cpu_init_exception_handling();
 	cpu_init();
+	fpu__init_cpu();
 }
 #endif
 
-/*
+#ifdef CONFIG_MICROCODE_LATE_LOADING
+/**
+ * store_cpu_caps() - Store a snapshot of CPU capabilities
+ * @curr_info: Pointer where to store it
+ *
+ * Returns: None
+ */
+void store_cpu_caps(struct cpuinfo_x86 *curr_info)
+{
+	/* Reload CPUID max function as it might've changed. */
+	curr_info->cpuid_level = cpuid_eax(0);
+
+	/* Copy all capability leafs and pick up the synthetic ones. */
+	memcpy(&curr_info->x86_capability, &boot_cpu_data.x86_capability,
+	       sizeof(curr_info->x86_capability));
+
+	/* Get the hardware CPUID leafs */
+	get_cpu_cap(curr_info);
+}
+
+/**
+ * microcode_check() - Check if any CPU capabilities changed after an update.
+ * @prev_info:	CPU capabilities stored before an update.
+ *
  * The microcode loader calls this upon late microcode load to recheck features,
  * only when microcode has been updated. Caller holds microcode_mutex and CPU
  * hotplug lock.
+ *
+ * Return: None
  */
-void microcode_check(void)
+void microcode_check(struct cpuinfo_x86 *prev_info)
 {
-	struct cpuinfo_x86 info;
+	struct cpuinfo_x86 curr_info;
 
 	perf_check_microcode();
 
-	/* Reload CPUID max function as it might've changed. */
-	info.cpuid_level = cpuid_eax(0);
-
-	/*
-	 * Copy all capability leafs to pick up the synthetic ones so that
-	 * memcmp() below doesn't fail on that. The ones coming from CPUID will
-	 * get overwritten in get_cpu_cap().
-	 */
-	memcpy(&info.x86_capability, &boot_cpu_data.x86_capability, sizeof(info.x86_capability));
+	amd_check_microcode();
 
-	get_cpu_cap(&info);
+	store_cpu_caps(&curr_info);
 
-	if (!memcmp(&info.x86_capability, &boot_cpu_data.x86_capability, sizeof(info.x86_capability)))
+	if (!memcmp(&prev_info->x86_capability, &curr_info.x86_capability,
+		    sizeof(prev_info->x86_capability)))
 		return;
 
 	pr_warn("x86/CPU: CPU features have changed after loading microcode, but might not take effect.\n");
 	pr_warn("x86/CPU: Please consider either early loading through initrd/built-in or a potential BIOS update.\n");
 }
+#endif
 
 /*
  * Invoked from core CPU hotplug code after hotplug operations
@@ -2069,3 +2368,69 @@
 	/* Check whether IPI broadcasting can be enabled */
 	apic_smt_update();
 }
+
+void __init arch_cpu_finalize_init(void)
+{
+	identify_boot_cpu();
+
+	/*
+	 * identify_boot_cpu() initialized SMT support information, let the
+	 * core code know.
+	 */
+	cpu_smt_check_topology();
+
+	if (!IS_ENABLED(CONFIG_SMP)) {
+		pr_info("CPU: ");
+		print_cpu_info(&boot_cpu_data);
+	}
+
+	cpu_select_mitigations();
+
+	arch_smt_update();
+
+	if (IS_ENABLED(CONFIG_X86_32)) {
+		/*
+		 * Check whether this is a real i386 which is not longer
+		 * supported and fixup the utsname.
+		 */
+		if (boot_cpu_data.x86 < 4)
+			panic("Kernel requires i486+ for 'invlpg' and other features");
+
+		init_utsname()->machine[1] =
+			'0' + (boot_cpu_data.x86 > 6 ? 6 : boot_cpu_data.x86);
+	}
+
+	/*
+	 * Must be before alternatives because it might set or clear
+	 * feature bits.
+	 */
+	fpu__init_system();
+	fpu__init_cpu();
+
+	alternative_instructions();
+
+	if (IS_ENABLED(CONFIG_X86_64)) {
+		/*
+		 * Make sure the first 2MB area is not mapped by huge pages
+		 * There are typically fixed size MTRRs in there and overlapping
+		 * MTRRs into large pages causes slow downs.
+		 *
+		 * Right now we don't do that with gbpages because there seems
+		 * very little benefit for that case.
+		 */
+		if (!direct_gbpages)
+			set_memory_4k((unsigned long)__va(0), 1);
+	} else {
+		fpu__init_check_bugs();
+	}
+
+	/*
+	 * This needs to be called before any devices perform DMA
+	 * operations that might use the SWIOTLB bounce buffers. It will
+	 * mark the bounce buffers as decrypted so that their usage will
+	 * not cause "plain-text" data to be decrypted when accessed. It
+	 * must be called after late_time_init() so that Hyper-V x86/x64
+	 * hypercalls work when the SWIOTLB bounce buffers are decrypted.
+	 */
+	mem_encrypt_init();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/cpu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/cpu.h
@@ -55,13 +55,14 @@
 extern __ro_after_init enum tsx_ctrl_states tsx_ctrl_state;
 
 extern void __init tsx_init(void);
-extern void tsx_enable(void);
-extern void tsx_disable(void);
-extern void tsx_clear_cpuid(void);
+void tsx_ap_init(void);
 #else
 static inline void tsx_init(void) { }
+static inline void tsx_ap_init(void) { }
 #endif /* CONFIG_CPU_SUP_INTEL */
 
+extern void init_spectral_chicken(struct cpuinfo_x86 *c);
+
 extern void get_cpu_cap(struct cpuinfo_x86 *c);
 extern void get_cpu_address_sizes(struct cpuinfo_x86 *c);
 extern void cpu_detect_cache_sizes(struct cpuinfo_x86 *c);
@@ -75,11 +76,14 @@
 extern int detect_extended_topology(struct cpuinfo_x86 *c);
 extern int detect_ht_early(struct cpuinfo_x86 *c);
 extern void detect_ht(struct cpuinfo_x86 *c);
+extern void check_null_seg_clears_base(struct cpuinfo_x86 *c);
 
 unsigned int aperfmperf_get_khz(int cpu);
+void cpu_select_mitigations(void);
 
 extern void x86_spec_ctrl_setup_ap(void);
 extern void update_srbds_msr(void);
+extern void update_gds_msr(void);
 
 extern u64 x86_read_arch_cap_msr(void);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/cpuid-deps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/cpuid-deps.c
@@ -44,7 +44,10 @@
 	{ X86_FEATURE_F16C,			X86_FEATURE_XMM2,     },
 	{ X86_FEATURE_AES,			X86_FEATURE_XMM2      },
 	{ X86_FEATURE_SHA_NI,			X86_FEATURE_XMM2      },
+	{ X86_FEATURE_GFNI,			X86_FEATURE_XMM2      },
 	{ X86_FEATURE_FMA,			X86_FEATURE_AVX       },
+	{ X86_FEATURE_VAES,			X86_FEATURE_AVX       },
+	{ X86_FEATURE_VPCLMULQDQ,		X86_FEATURE_AVX       },
 	{ X86_FEATURE_AVX2,			X86_FEATURE_AVX,      },
 	{ X86_FEATURE_AVX512F,			X86_FEATURE_AVX,      },
 	{ X86_FEATURE_AVX512IFMA,		X86_FEATURE_AVX512F   },
@@ -56,9 +59,6 @@
 	{ X86_FEATURE_AVX512VL,			X86_FEATURE_AVX512F   },
 	{ X86_FEATURE_AVX512VBMI,		X86_FEATURE_AVX512F   },
 	{ X86_FEATURE_AVX512_VBMI2,		X86_FEATURE_AVX512VL  },
-	{ X86_FEATURE_GFNI,			X86_FEATURE_AVX512VL  },
-	{ X86_FEATURE_VAES,			X86_FEATURE_AVX512VL  },
-	{ X86_FEATURE_VPCLMULQDQ,		X86_FEATURE_AVX512VL  },
 	{ X86_FEATURE_AVX512_VNNI,		X86_FEATURE_AVX512VL  },
 	{ X86_FEATURE_AVX512_BITALG,		X86_FEATURE_AVX512VL  },
 	{ X86_FEATURE_AVX512_4VNNIW,		X86_FEATURE_AVX512F   },
@@ -75,6 +75,8 @@
 	{ X86_FEATURE_SGX_LC,			X86_FEATURE_SGX	      },
 	{ X86_FEATURE_SGX1,			X86_FEATURE_SGX       },
 	{ X86_FEATURE_SGX2,			X86_FEATURE_SGX1      },
+	{ X86_FEATURE_XFD,			X86_FEATURE_XSAVES    },
+	{ X86_FEATURE_AMX_TILE,			X86_FEATURE_XFD       },
 	{}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/cyrix.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/cyrix.c
@@ -152,8 +152,8 @@
 	u8 ccr3;
 	local_irq_save(flags);
 
-	/* Suspend on halt power saving and enable #SUSP pin */
-	setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
+	/* Suspend on halt power saving */
+	setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x08);
 
 	ccr3 = getCx86(CX86_CCR3);
 	setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10);	/* enable MAPEN */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/feat_ctl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/feat_ctl.c
@@ -1,11 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <linux/tboot.h>
 
+#include <asm/cpu.h>
 #include <asm/cpufeature.h>
 #include <asm/msr-index.h>
 #include <asm/processor.h>
 #include <asm/vmx.h>
-#include "cpu.h"
 
 #undef pr_fmt
 #define pr_fmt(fmt)	"x86/cpu: " fmt
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/hygon.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/hygon.c
@@ -86,8 +86,12 @@
 		if (!err)
 			c->x86_coreid_bits = get_count_order(c->x86_max_cores);
 
-		/* Socket ID is ApicId[6] for these processors. */
-		c->phys_proc_id = c->apicid >> APICID_SOCKET_ID_BIT;
+		/*
+		 * Socket ID is ApicId[6] for the processors with model <= 0x3
+		 * when running on host.
+		 */
+		if (!boot_cpu_has(X86_FEATURE_HYPERVISOR) && c->x86_model <= 0x3)
+			c->phys_proc_id = c->apicid >> APICID_SOCKET_ID_BIT;
 
 		cacheinfo_hygon_init_llc_id(c, cpu);
 	} else if (cpu_has(c, X86_FEATURE_NODEID_MSR)) {
@@ -302,6 +306,12 @@
 	/* get apicid instead of initial apic id from cpuid */
 	c->apicid = hard_smp_processor_id();
 
+	/*
+	 * XXX someone from Hygon needs to confirm this DTRT
+	 *
+	init_spectral_chicken(c);
+	 */
+
 	set_cpu_cap(c, X86_FEATURE_ZEN);
 	set_cpu_cap(c, X86_FEATURE_CPB);
 
@@ -320,8 +330,8 @@
 		 * msr_set_bit() uses the safe accessors, too, even if the MSR
 		 * is not present.
 		 */
-		msr_set_bit(MSR_F10H_DECFG,
-			    MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT);
+		msr_set_bit(MSR_AMD64_DE_CFG,
+			    MSR_AMD64_DE_CFG_LFENCE_SERIALIZE_BIT);
 
 		/* A serializing LFENCE stops RDTSC speculation */
 		set_cpu_cap(c, X86_FEATURE_LFENCE_RDTSC);
@@ -335,6 +345,11 @@
 	/* Hygon CPUs don't reset SS attributes on SYSRET, Xen does. */
 	if (!cpu_has(c, X86_FEATURE_XENPV))
 		set_cpu_bug(c, X86_BUG_SYSRET_SS_ATTRS);
+
+	check_null_seg_clears_base(c);
+
+	/* Hygon CPUs don't need fencing after x2APIC/TSC_DEADLINE MSR writes. */
+	clear_cpu_cap(c, X86_FEATURE_APIC_MSRS_FENCE);
 }
 
 static void cpu_detect_tlb_hygon(struct cpuinfo_x86 *c)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/intel.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/intel.c
@@ -91,7 +91,7 @@
 static int __init ring3mwait_disable(char *__unused)
 {
 	ring3mwait_disabled = true;
-	return 0;
+	return 1;
 }
 __setup("ring3mwait=disable", ring3mwait_disable);
 
@@ -181,6 +181,90 @@
 	return false;
 }
 
+#define MSR_IA32_TME_ACTIVATE		0x982
+
+/* Helpers to access TME_ACTIVATE MSR */
+#define TME_ACTIVATE_LOCKED(x)		(x & 0x1)
+#define TME_ACTIVATE_ENABLED(x)		(x & 0x2)
+
+#define TME_ACTIVATE_POLICY(x)		((x >> 4) & 0xf)	/* Bits 7:4 */
+#define TME_ACTIVATE_POLICY_AES_XTS_128	0
+
+#define TME_ACTIVATE_KEYID_BITS(x)	((x >> 32) & 0xf)	/* Bits 35:32 */
+
+#define TME_ACTIVATE_CRYPTO_ALGS(x)	((x >> 48) & 0xffff)	/* Bits 63:48 */
+#define TME_ACTIVATE_CRYPTO_AES_XTS_128	1
+
+/* Values for mktme_status (SW only construct) */
+#define MKTME_ENABLED			0
+#define MKTME_DISABLED			1
+#define MKTME_UNINITIALIZED		2
+static int mktme_status = MKTME_UNINITIALIZED;
+
+static void detect_tme_early(struct cpuinfo_x86 *c)
+{
+	u64 tme_activate, tme_policy, tme_crypto_algs;
+	int keyid_bits = 0, nr_keyids = 0;
+	static u64 tme_activate_cpu0 = 0;
+
+	rdmsrl(MSR_IA32_TME_ACTIVATE, tme_activate);
+
+	if (mktme_status != MKTME_UNINITIALIZED) {
+		if (tme_activate != tme_activate_cpu0) {
+			/* Broken BIOS? */
+			pr_err_once("x86/tme: configuration is inconsistent between CPUs\n");
+			pr_err_once("x86/tme: MKTME is not usable\n");
+			mktme_status = MKTME_DISABLED;
+
+			/* Proceed. We may need to exclude bits from x86_phys_bits. */
+		}
+	} else {
+		tme_activate_cpu0 = tme_activate;
+	}
+
+	if (!TME_ACTIVATE_LOCKED(tme_activate) || !TME_ACTIVATE_ENABLED(tme_activate)) {
+		pr_info_once("x86/tme: not enabled by BIOS\n");
+		mktme_status = MKTME_DISABLED;
+		return;
+	}
+
+	if (mktme_status != MKTME_UNINITIALIZED)
+		goto detect_keyid_bits;
+
+	pr_info("x86/tme: enabled by BIOS\n");
+
+	tme_policy = TME_ACTIVATE_POLICY(tme_activate);
+	if (tme_policy != TME_ACTIVATE_POLICY_AES_XTS_128)
+		pr_warn("x86/tme: Unknown policy is active: %#llx\n", tme_policy);
+
+	tme_crypto_algs = TME_ACTIVATE_CRYPTO_ALGS(tme_activate);
+	if (!(tme_crypto_algs & TME_ACTIVATE_CRYPTO_AES_XTS_128)) {
+		pr_err("x86/mktme: No known encryption algorithm is supported: %#llx\n",
+				tme_crypto_algs);
+		mktme_status = MKTME_DISABLED;
+	}
+detect_keyid_bits:
+	keyid_bits = TME_ACTIVATE_KEYID_BITS(tme_activate);
+	nr_keyids = (1UL << keyid_bits) - 1;
+	if (nr_keyids) {
+		pr_info_once("x86/mktme: enabled by BIOS\n");
+		pr_info_once("x86/mktme: %d KeyIDs available\n", nr_keyids);
+	} else {
+		pr_info_once("x86/mktme: disabled by BIOS\n");
+	}
+
+	if (mktme_status == MKTME_UNINITIALIZED) {
+		/* MKTME is usable */
+		mktme_status = MKTME_ENABLED;
+	}
+
+	/*
+	 * KeyID bits effectively lower the number of physical address
+	 * bits.  Update cpuinfo_x86::x86_phys_bits accordingly.
+	 */
+	c->x86_phys_bits -= keyid_bits;
+}
+
 static void early_init_intel(struct cpuinfo_x86 *c)
 {
 	u64 misc_enable;
@@ -332,6 +416,13 @@
 	 */
 	if (detect_extended_topology_early(c) < 0)
 		detect_ht_early(c);
+
+	/*
+	 * Adjust the number of physical bits early because it affects the
+	 * valid bits of the MTRR mask registers.
+	 */
+	if (cpu_has(c, X86_FEATURE_TME))
+		detect_tme_early(c);
 }
 
 static void bsp_init_intel(struct cpuinfo_x86 *c)
@@ -492,90 +583,6 @@
 #endif
 }
 
-#define MSR_IA32_TME_ACTIVATE		0x982
-
-/* Helpers to access TME_ACTIVATE MSR */
-#define TME_ACTIVATE_LOCKED(x)		(x & 0x1)
-#define TME_ACTIVATE_ENABLED(x)		(x & 0x2)
-
-#define TME_ACTIVATE_POLICY(x)		((x >> 4) & 0xf)	/* Bits 7:4 */
-#define TME_ACTIVATE_POLICY_AES_XTS_128	0
-
-#define TME_ACTIVATE_KEYID_BITS(x)	((x >> 32) & 0xf)	/* Bits 35:32 */
-
-#define TME_ACTIVATE_CRYPTO_ALGS(x)	((x >> 48) & 0xffff)	/* Bits 63:48 */
-#define TME_ACTIVATE_CRYPTO_AES_XTS_128	1
-
-/* Values for mktme_status (SW only construct) */
-#define MKTME_ENABLED			0
-#define MKTME_DISABLED			1
-#define MKTME_UNINITIALIZED		2
-static int mktme_status = MKTME_UNINITIALIZED;
-
-static void detect_tme(struct cpuinfo_x86 *c)
-{
-	u64 tme_activate, tme_policy, tme_crypto_algs;
-	int keyid_bits = 0, nr_keyids = 0;
-	static u64 tme_activate_cpu0 = 0;
-
-	rdmsrl(MSR_IA32_TME_ACTIVATE, tme_activate);
-
-	if (mktme_status != MKTME_UNINITIALIZED) {
-		if (tme_activate != tme_activate_cpu0) {
-			/* Broken BIOS? */
-			pr_err_once("x86/tme: configuration is inconsistent between CPUs\n");
-			pr_err_once("x86/tme: MKTME is not usable\n");
-			mktme_status = MKTME_DISABLED;
-
-			/* Proceed. We may need to exclude bits from x86_phys_bits. */
-		}
-	} else {
-		tme_activate_cpu0 = tme_activate;
-	}
-
-	if (!TME_ACTIVATE_LOCKED(tme_activate) || !TME_ACTIVATE_ENABLED(tme_activate)) {
-		pr_info_once("x86/tme: not enabled by BIOS\n");
-		mktme_status = MKTME_DISABLED;
-		return;
-	}
-
-	if (mktme_status != MKTME_UNINITIALIZED)
-		goto detect_keyid_bits;
-
-	pr_info("x86/tme: enabled by BIOS\n");
-
-	tme_policy = TME_ACTIVATE_POLICY(tme_activate);
-	if (tme_policy != TME_ACTIVATE_POLICY_AES_XTS_128)
-		pr_warn("x86/tme: Unknown policy is active: %#llx\n", tme_policy);
-
-	tme_crypto_algs = TME_ACTIVATE_CRYPTO_ALGS(tme_activate);
-	if (!(tme_crypto_algs & TME_ACTIVATE_CRYPTO_AES_XTS_128)) {
-		pr_err("x86/mktme: No known encryption algorithm is supported: %#llx\n",
-				tme_crypto_algs);
-		mktme_status = MKTME_DISABLED;
-	}
-detect_keyid_bits:
-	keyid_bits = TME_ACTIVATE_KEYID_BITS(tme_activate);
-	nr_keyids = (1UL << keyid_bits) - 1;
-	if (nr_keyids) {
-		pr_info_once("x86/mktme: enabled by BIOS\n");
-		pr_info_once("x86/mktme: %d KeyIDs available\n", nr_keyids);
-	} else {
-		pr_info_once("x86/mktme: disabled by BIOS\n");
-	}
-
-	if (mktme_status == MKTME_UNINITIALIZED) {
-		/* MKTME is usable */
-		mktme_status = MKTME_ENABLED;
-	}
-
-	/*
-	 * KeyID bits effectively lower the number of physical address
-	 * bits.  Update cpuinfo_x86::x86_phys_bits accordingly.
-	 */
-	c->x86_phys_bits -= keyid_bits;
-}
-
 static void init_cpuid_fault(struct cpuinfo_x86 *c)
 {
 	u64 msr;
@@ -712,18 +719,8 @@
 
 	init_ia32_feat_ctl(c);
 
-	if (cpu_has(c, X86_FEATURE_TME))
-		detect_tme(c);
-
 	init_intel_misc_features(c);
 
-	if (tsx_ctrl_state == TSX_CTRL_ENABLE)
-		tsx_enable();
-	else if (tsx_ctrl_state == TSX_CTRL_DISABLE)
-		tsx_disable();
-	else if (tsx_ctrl_state == TSX_CTRL_RTM_ALWAYS_ABORT)
-		tsx_clear_cpuid();
-
 	split_lock_init();
 	bus_lock_init();
 
@@ -752,26 +749,37 @@
 }
 #endif
 
-#define TLB_INST_4K	0x01
-#define TLB_INST_4M	0x02
-#define TLB_INST_2M_4M	0x03
-
-#define TLB_INST_ALL	0x05
-#define TLB_INST_1G	0x06
-
-#define TLB_DATA_4K	0x11
-#define TLB_DATA_4M	0x12
-#define TLB_DATA_2M_4M	0x13
-#define TLB_DATA_4K_4M	0x14
-
-#define TLB_DATA_1G	0x16
-
-#define TLB_DATA0_4K	0x21
-#define TLB_DATA0_4M	0x22
-#define TLB_DATA0_2M_4M	0x23
+#define TLB_INST_4K		0x01
+#define TLB_INST_4M		0x02
+#define TLB_INST_2M_4M		0x03
+
+#define TLB_INST_ALL		0x05
+#define TLB_INST_1G		0x06
+
+#define TLB_DATA_4K		0x11
+#define TLB_DATA_4M		0x12
+#define TLB_DATA_2M_4M		0x13
+#define TLB_DATA_4K_4M		0x14
+
+#define TLB_DATA_1G		0x16
+#define TLB_DATA_1G_2M_4M	0x17
+
+#define TLB_DATA0_4K		0x21
+#define TLB_DATA0_4M		0x22
+#define TLB_DATA0_2M_4M		0x23
+
+#define STLB_4K			0x41
+#define STLB_4K_2M		0x42
 
-#define STLB_4K		0x41
-#define STLB_4K_2M	0x42
+/*
+ * All of leaf 0x2's one-byte TLB descriptors implies the same number of
+ * entries for their respective TLB types.  The 0x63 descriptor is an
+ * exception: it implies 4 dTLB entries for 1GB pages 32 dTLB entries
+ * for 2MB or 4MB pages.  Encode descriptor 0x63 dTLB entry count for
+ * 2MB/4MB pages here, as its count for dTLB 1GB pages is already at the
+ * intel_tlb_table[] mapping.
+ */
+#define TLB_0x63_2M_4M_ENTRIES	32
 
 static const struct _tlb_table intel_tlb_table[] = {
 	{ 0x01, TLB_INST_4K,		32,	" TLB_INST 4 KByte pages, 4-way set associative" },
@@ -793,7 +801,8 @@
 	{ 0x5c, TLB_DATA_4K_4M,		128,	" TLB_DATA 4 KByte and 4 MByte pages" },
 	{ 0x5d, TLB_DATA_4K_4M,		256,	" TLB_DATA 4 KByte and 4 MByte pages" },
 	{ 0x61, TLB_INST_4K,		48,	" TLB_INST 4 KByte pages, full associative" },
-	{ 0x63, TLB_DATA_1G,		4,	" TLB_DATA 1 GByte pages, 4-way set associative" },
+	{ 0x63, TLB_DATA_1G_2M_4M,	4,	" TLB_DATA 1 GByte pages, 4-way set associative"
+						" (plus 32 entries TLB_DATA 2 MByte or 4 MByte pages, not encoded here)" },
 	{ 0x6b, TLB_DATA_4K,		256,	" TLB_DATA 4 KByte pages, 8-way associative" },
 	{ 0x6c, TLB_DATA_2M_4M,		128,	" TLB_DATA 2 MByte or 4 MByte pages, 8-way associative" },
 	{ 0x6d, TLB_DATA_1G,		16,	" TLB_DATA 1 GByte pages, fully associative" },
@@ -893,6 +902,12 @@
 		if (tlb_lld_4m[ENTRIES] < intel_tlb_table[k].entries)
 			tlb_lld_4m[ENTRIES] = intel_tlb_table[k].entries;
 		break;
+	case TLB_DATA_1G_2M_4M:
+		if (tlb_lld_2m[ENTRIES] < TLB_0x63_2M_4M_ENTRIES)
+			tlb_lld_2m[ENTRIES] = TLB_0x63_2M_4M_ENTRIES;
+		if (tlb_lld_4m[ENTRIES] < TLB_0x63_2M_4M_ENTRIES)
+			tlb_lld_4m[ENTRIES] = TLB_0x63_2M_4M_ENTRIES;
+		fallthrough;
 	case TLB_DATA_1G:
 		if (tlb_lld_1g[ENTRIES] < intel_tlb_table[k].entries)
 			tlb_lld_1g[ENTRIES] = intel_tlb_table[k].entries;
@@ -916,7 +931,7 @@
 		cpuid(2, &regs[0], &regs[1], &regs[2], &regs[3]);
 
 		/* If bit 31 is set, this is an unknown format */
-		for (j = 0 ; j < 3 ; j++)
+		for (j = 0 ; j < 4 ; j++)
 			if (regs[j] & (1 << 31))
 				regs[j] = 0;
 
@@ -1152,22 +1167,23 @@
 {
 	u64 val;
 
-	/*
-	 * Warn and fatal are handled by #AC for split lock if #AC for
-	 * split lock is supported.
-	 */
-	if (!boot_cpu_has(X86_FEATURE_BUS_LOCK_DETECT) ||
-	    (boot_cpu_has(X86_FEATURE_SPLIT_LOCK_DETECT) &&
-	    (sld_state == sld_warn || sld_state == sld_fatal)) ||
-	    sld_state == sld_off)
+	if (!boot_cpu_has(X86_FEATURE_BUS_LOCK_DETECT))
 		return;
 
-	/*
-	 * Enable #DB for bus lock. All bus locks are handled in #DB except
-	 * split locks are handled in #AC in the fatal case.
-	 */
 	rdmsrl(MSR_IA32_DEBUGCTLMSR, val);
-	val |= DEBUGCTLMSR_BUS_LOCK_DETECT;
+
+	if ((boot_cpu_has(X86_FEATURE_SPLIT_LOCK_DETECT) &&
+	    (sld_state == sld_warn || sld_state == sld_fatal)) ||
+	    sld_state == sld_off) {
+		/*
+		 * Warn and fatal are handled by #AC for split lock if #AC for
+		 * split lock is supported.
+		 */
+		val &= ~DEBUGCTLMSR_BUS_LOCK_DETECT;
+	} else {
+		val |= DEBUGCTLMSR_BUS_LOCK_DETECT;
+	}
+
 	wrmsrl(MSR_IA32_DEBUGCTLMSR, val);
 }
 
@@ -1213,30 +1229,13 @@
 }
 
 /*
- * Bits in the IA32_CORE_CAPABILITIES are not architectural, so they should
- * only be trusted if it is confirmed that a CPU model implements a
- * specific feature at a particular bit position.
- *
- * The possible driver data field values:
- *
- * - 0: CPU models that are known to have the per-core split-lock detection
- *	feature even though they do not enumerate IA32_CORE_CAPABILITIES.
- *
- * - 1: CPU models which may enumerate IA32_CORE_CAPABILITIES and if so use
- *      bit 5 to enumerate the per-core split-lock detection feature.
+ * CPU models that are known to have the per-core split-lock detection
+ * feature even though they do not enumerate IA32_CORE_CAPABILITIES.
  */
 static const struct x86_cpu_id split_lock_cpu_ids[] __initconst = {
-	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X,		0),
-	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_L,		0),
-	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_D,		0),
-	X86_MATCH_INTEL_FAM6_MODEL(ATOM_TREMONT,	1),
-	X86_MATCH_INTEL_FAM6_MODEL(ATOM_TREMONT_D,	1),
-	X86_MATCH_INTEL_FAM6_MODEL(ATOM_TREMONT_L,	1),
-	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE_L,		1),
-	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE,		1),
-	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X,	1),
-	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE,		1),
-	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L,		1),
+	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X,	0),
+	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_L,	0),
+	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_D,	0),
 	{}
 };
 
@@ -1248,24 +1247,27 @@
 	if (boot_cpu_has(X86_FEATURE_HYPERVISOR))
 		return;
 
+	/* Check for CPUs that have support but do not enumerate it: */
 	m = x86_match_cpu(split_lock_cpu_ids);
-	if (!m)
-		return;
+	if (m)
+		goto supported;
 
-	switch (m->driver_data) {
-	case 0:
-		break;
-	case 1:
-		if (!cpu_has(c, X86_FEATURE_CORE_CAPABILITIES))
-			return;
-		rdmsrl(MSR_IA32_CORE_CAPS, ia32_core_caps);
-		if (!(ia32_core_caps & MSR_IA32_CORE_CAPS_SPLIT_LOCK_DETECT))
-			return;
-		break;
-	default:
+	if (!cpu_has(c, X86_FEATURE_CORE_CAPABILITIES))
 		return;
-	}
 
+	/*
+	 * Not all bits in MSR_IA32_CORE_CAPS are architectural, but
+	 * MSR_IA32_CORE_CAPS_SPLIT_LOCK_DETECT is.  All CPUs that set
+	 * it have split lock detection.
+	 */
+	rdmsrl(MSR_IA32_CORE_CAPS, ia32_core_caps);
+	if (ia32_core_caps & MSR_IA32_CORE_CAPS_SPLIT_LOCK_DETECT)
+		goto supported;
+
+	/* CPU is not in the model list and does not have the MSR bit: */
+	return;
+
+supported:
 	cpu_model_supports_sld = true;
 	__split_lock_setup();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/match.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/match.c
@@ -39,9 +39,7 @@
 	const struct x86_cpu_id *m;
 	struct cpuinfo_x86 *c = &boot_cpu_data;
 
-	for (m = match;
-	     m->vendor | m->family | m->model | m->steppings | m->feature;
-	     m++) {
+	for (m = match; m->flags & X86_CPU_ID_FLAG_ENTRY_VALID; m++) {
 		if (m->vendor != X86_VENDOR_ANY && c->x86_vendor != m->vendor)
 			continue;
 		if (m->family != X86_FAMILY_ANY && c->x86 != m->family)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/amd.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/amd.c
@@ -210,10 +210,10 @@
  * A list of the banks enabled on each logical CPU. Controls which respective
  * descriptors to initialize later in mce_threshold_create_device().
  */
-static DEFINE_PER_CPU(unsigned int, bank_map);
+static DEFINE_PER_CPU(u64, bank_map);
 
 /* Map of banks that have more than MCA_MISC0 available. */
-static DEFINE_PER_CPU(u32, smca_misc_banks_map);
+static DEFINE_PER_CPU(u64, smca_misc_banks_map);
 
 static void amd_threshold_interrupt(void);
 static void amd_deferred_error_interrupt(void);
@@ -242,7 +242,7 @@
 		return;
 
 	if (low & MASK_BLKPTR_LO)
-		per_cpu(smca_misc_banks_map, cpu) |= BIT(bank);
+		per_cpu(smca_misc_banks_map, cpu) |= BIT_ULL(bank);
 
 }
 
@@ -400,7 +400,7 @@
 	u32 hi, lo;
 
 	/* sysfs write might race against an offline operation */
-	if (this_cpu_read(threshold_banks))
+	if (!this_cpu_read(threshold_banks) && !tr->set_lvt_off)
 		return;
 
 	rdmsr(tr->b->address, lo, hi);
@@ -505,7 +505,7 @@
 	if (!block)
 		return MSR_AMD64_SMCA_MCx_MISC(bank);
 
-	if (!(per_cpu(smca_misc_banks_map, cpu) & BIT(bank)))
+	if (!(per_cpu(smca_misc_banks_map, cpu) & BIT_ULL(bank)))
 		return 0;
 
 	return MSR_AMD64_SMCA_MCx_MISCy(bank, block - 1);
@@ -526,7 +526,7 @@
 	/* Fall back to method we used for older processors: */
 	switch (block) {
 	case 0:
-		addr = msr_ops.misc(bank);
+		addr = mca_msr_reg(bank, MCA_MISC);
 		break;
 	case 1:
 		offset = ((low & MASK_BLKPTR_LO) >> 21);
@@ -549,7 +549,7 @@
 	int new;
 
 	if (!block)
-		per_cpu(bank_map, cpu) |= (1 << bank);
+		per_cpu(bank_map, cpu) |= BIT_ULL(bank);
 
 	memset(&b, 0, sizeof(b));
 	b.cpu			= cpu;
@@ -965,6 +965,24 @@
 	return status & MCI_STATUS_DEFERRED;
 }
 
+static bool _log_error_deferred(unsigned int bank, u32 misc)
+{
+	if (!_log_error_bank(bank, mca_msr_reg(bank, MCA_STATUS),
+			     mca_msr_reg(bank, MCA_ADDR), misc))
+		return false;
+
+	/*
+	 * Non-SMCA systems don't have MCA_DESTAT/MCA_DEADDR registers.
+	 * Return true here to avoid accessing these registers.
+	 */
+	if (!mce_flags.smca)
+		return true;
+
+	/* Clear MCA_DESTAT if the deferred error was logged from MCA_STATUS. */
+	wrmsrl(MSR_AMD64_SMCA_MCx_DESTAT(bank), 0);
+	return true;
+}
+
 /*
  * We have three scenarios for checking for Deferred errors:
  *
@@ -976,20 +994,9 @@
  */
 static void log_error_deferred(unsigned int bank)
 {
-	bool defrd;
-
-	defrd = _log_error_bank(bank, msr_ops.status(bank),
-					msr_ops.addr(bank), 0);
-
-	if (!mce_flags.smca)
+	if (_log_error_deferred(bank, 0))
 		return;
 
-	/* Clear MCA_DESTAT if we logged the deferred error from MCA_STATUS. */
-	if (defrd) {
-		wrmsrl(MSR_AMD64_SMCA_MCx_DESTAT(bank), 0);
-		return;
-	}
-
 	/*
 	 * Only deferred errors are logged in MCA_DE{STAT,ADDR} so just check
 	 * for a valid error.
@@ -1009,7 +1016,7 @@
 
 static void log_error_thresholding(unsigned int bank, u64 misc)
 {
-	_log_error_bank(bank, msr_ops.status(bank), msr_ops.addr(bank), misc);
+	_log_error_deferred(bank, misc);
 }
 
 static void log_and_reset_block(struct threshold_block *block)
@@ -1054,7 +1061,7 @@
 		return;
 
 	for (bank = 0; bank < this_cpu_read(mce_num_banks); ++bank) {
-		if (!(per_cpu(bank_map, cpu) & (1 << bank)))
+		if (!(per_cpu(bank_map, cpu) & BIT_ULL(bank)))
 			continue;
 
 		first_block = bp[bank]->blocks;
@@ -1397,7 +1404,7 @@
 		}
 	}
 
-	err = allocate_threshold_blocks(cpu, b, bank, 0, msr_ops.misc(bank));
+	err = allocate_threshold_blocks(cpu, b, bank, 0, mca_msr_reg(bank, MCA_MISC));
 	if (err)
 		goto out_kobj;
 
@@ -1470,10 +1477,23 @@
 	kfree(bank);
 }
 
+static void __threshold_remove_device(struct threshold_bank **bp)
+{
+	unsigned int bank, numbanks = this_cpu_read(mce_num_banks);
+
+	for (bank = 0; bank < numbanks; bank++) {
+		if (!bp[bank])
+			continue;
+
+		threshold_remove_bank(bp[bank]);
+		bp[bank] = NULL;
+	}
+	kfree(bp);
+}
+
 int mce_threshold_remove_device(unsigned int cpu)
 {
 	struct threshold_bank **bp = this_cpu_read(threshold_banks);
-	unsigned int bank, numbanks = this_cpu_read(mce_num_banks);
 
 	if (!bp)
 		return 0;
@@ -1484,13 +1504,7 @@
 	 */
 	this_cpu_write(threshold_banks, NULL);
 
-	for (bank = 0; bank < numbanks; bank++) {
-		if (bp[bank]) {
-			threshold_remove_bank(bp[bank]);
-			bp[bank] = NULL;
-		}
-	}
-	kfree(bp);
+	__threshold_remove_device(bp);
 	return 0;
 }
 
@@ -1524,18 +1538,17 @@
 		return -ENOMEM;
 
 	for (bank = 0; bank < numbanks; ++bank) {
-		if (!(this_cpu_read(bank_map) & (1 << bank)))
+		if (!(this_cpu_read(bank_map) & BIT_ULL(bank)))
 			continue;
 		err = threshold_create_bank(bp, cpu, bank);
-		if (err)
-			goto out_err;
+		if (err) {
+			__threshold_remove_device(bp);
+			return err;
+		}
 	}
 	this_cpu_write(threshold_banks, bp);
 
 	if (thresholding_irq_en)
 		mce_threshold_vector = amd_threshold_interrupt;
 	return 0;
-out_err:
-	mce_threshold_remove_device(cpu);
-	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/apei.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/apei.c
@@ -29,15 +29,26 @@
 void apei_mce_report_mem_error(int severity, struct cper_sec_mem_err *mem_err)
 {
 	struct mce m;
+	int lsb;
 
 	if (!(mem_err->validation_bits & CPER_MEM_VALID_PA))
 		return;
 
+	/*
+	 * Even if the ->validation_bits are set for address mask,
+	 * to be extra safe, check and reject an error radius '0',
+	 * and fall back to the default page size.
+	 */
+	if (mem_err->validation_bits & CPER_MEM_VALID_PA_MASK)
+		lsb = find_first_bit((void *)&mem_err->physical_addr_mask, PAGE_SHIFT);
+	else
+		lsb = PAGE_SHIFT;
+
 	mce_setup(&m);
 	m.bank = -1;
 	/* Fake a memory read error with unknown channel */
 	m.status = MCI_STATUS_VAL | MCI_STATUS_EN | MCI_STATUS_ADDRV | MCI_STATUS_MISCV | 0x9f;
-	m.misc = (MCI_MISC_ADDR_PHYS << 6) | PAGE_SHIFT;
+	m.misc = (MCI_MISC_ADDR_PHYS << 6) | lsb;
 
 	if (severity >= GHES_SEV_RECOVERABLE)
 		m.status |= MCI_STATUS_UC;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/core.c
@@ -44,6 +44,7 @@
 #include <linux/sync_core.h>
 #include <linux/task_work.h>
 #include <linux/hardirq.h>
+#include <linux/kexec.h>
 
 #include <asm/intel-family.h>
 #include <asm/processor.h>
@@ -176,53 +177,27 @@
 }
 EXPORT_SYMBOL_GPL(mce_unregister_decode_chain);
 
-static inline u32 ctl_reg(int bank)
+u32 mca_msr_reg(int bank, enum mca_msr reg)
 {
-	return MSR_IA32_MCx_CTL(bank);
-}
-
-static inline u32 status_reg(int bank)
-{
-	return MSR_IA32_MCx_STATUS(bank);
-}
-
-static inline u32 addr_reg(int bank)
-{
-	return MSR_IA32_MCx_ADDR(bank);
-}
-
-static inline u32 misc_reg(int bank)
-{
-	return MSR_IA32_MCx_MISC(bank);
-}
-
-static inline u32 smca_ctl_reg(int bank)
-{
-	return MSR_AMD64_SMCA_MCx_CTL(bank);
-}
-
-static inline u32 smca_status_reg(int bank)
-{
-	return MSR_AMD64_SMCA_MCx_STATUS(bank);
-}
+	if (mce_flags.smca) {
+		switch (reg) {
+		case MCA_CTL:	 return MSR_AMD64_SMCA_MCx_CTL(bank);
+		case MCA_ADDR:	 return MSR_AMD64_SMCA_MCx_ADDR(bank);
+		case MCA_MISC:	 return MSR_AMD64_SMCA_MCx_MISC(bank);
+		case MCA_STATUS: return MSR_AMD64_SMCA_MCx_STATUS(bank);
+		}
+	}
 
-static inline u32 smca_addr_reg(int bank)
-{
-	return MSR_AMD64_SMCA_MCx_ADDR(bank);
-}
+	switch (reg) {
+	case MCA_CTL:	 return MSR_IA32_MCx_CTL(bank);
+	case MCA_ADDR:	 return MSR_IA32_MCx_ADDR(bank);
+	case MCA_MISC:	 return MSR_IA32_MCx_MISC(bank);
+	case MCA_STATUS: return MSR_IA32_MCx_STATUS(bank);
+	}
 
-static inline u32 smca_misc_reg(int bank)
-{
-	return MSR_AMD64_SMCA_MCx_MISC(bank);
+	return 0;
 }
 
-struct mca_msr_regs msr_ops = {
-	.ctl	= ctl_reg,
-	.status	= status_reg,
-	.addr	= addr_reg,
-	.misc	= misc_reg
-};
-
 static void __print_mce(struct mce *m)
 {
 	pr_emerg(HW_ERR "CPU %d: Machine Check%s: %Lx Bank %d: %016Lx\n",
@@ -295,11 +270,18 @@
 	panic("Panicing machine check CPU died");
 }
 
-static void mce_panic(const char *msg, struct mce *final, char *exp)
+static noinstr void mce_panic(const char *msg, struct mce *final, char *exp)
 {
-	int apei_err = 0;
 	struct llist_node *pending;
 	struct mce_evt_llist *l;
+	int apei_err = 0;
+	struct page *p;
+
+	/*
+	 * Allow instrumentation around external facilities usage. Not that it
+	 * matters a whole lot since the machine is going to panic anyway.
+	 */
+	instrumentation_begin();
 
 	if (!fake_panic) {
 		/*
@@ -314,7 +296,7 @@
 	} else {
 		/* Don't log too much for fake panic */
 		if (atomic_inc_return(&mce_fake_panicked) > 1)
-			return;
+			goto out;
 	}
 	pending = mce_gen_pool_prepare_records();
 	/* First print corrected ones that are still unlogged */
@@ -349,9 +331,26 @@
 	if (!fake_panic) {
 		if (panic_timeout == 0)
 			panic_timeout = mca_cfg.panic_timeout;
+
+		/*
+		 * Kdump skips the poisoned page in order to avoid
+		 * touching the error bits again. Poison the page even
+		 * if the error is fatal and the machine is about to
+		 * panic.
+		 */
+		if (kexec_crash_loaded()) {
+			if (final && (final->status & MCI_STATUS_ADDRV)) {
+				p = pfn_to_online_page(final->addr >> PAGE_SHIFT);
+				if (p)
+					SetPageHWPoison(p);
+			}
+		}
 		panic(msg);
 	} else
 		pr_emerg(HW_ERR "Fake kernel panic: %s\n", msg);
+
+out:
+	instrumentation_end();
 }
 
 /* Support code for software error injection */
@@ -362,24 +361,27 @@
 
 	if (msr == mca_cfg.rip_msr)
 		return offsetof(struct mce, ip);
-	if (msr == msr_ops.status(bank))
+	if (msr == mca_msr_reg(bank, MCA_STATUS))
 		return offsetof(struct mce, status);
-	if (msr == msr_ops.addr(bank))
+	if (msr == mca_msr_reg(bank, MCA_ADDR))
 		return offsetof(struct mce, addr);
-	if (msr == msr_ops.misc(bank))
+	if (msr == mca_msr_reg(bank, MCA_MISC))
 		return offsetof(struct mce, misc);
 	if (msr == MSR_IA32_MCG_STATUS)
 		return offsetof(struct mce, mcgstatus);
 	return -1;
 }
 
-__visible bool ex_handler_rdmsr_fault(const struct exception_table_entry *fixup,
-				      struct pt_regs *regs, int trapnr,
-				      unsigned long error_code,
-				      unsigned long fault_addr)
+void ex_handler_msr_mce(struct pt_regs *regs, bool wrmsr)
 {
-	pr_emerg("MSR access error: RDMSR from 0x%x at rIP: 0x%lx (%pS)\n",
-		 (unsigned int)regs->cx, regs->ip, (void *)regs->ip);
+	if (wrmsr) {
+		pr_emerg("MSR access error: WRMSR to 0x%x (tried to write 0x%08x%08x) at rIP: 0x%lx (%pS)\n",
+			 (unsigned int)regs->cx, (unsigned int)regs->dx, (unsigned int)regs->ax,
+			 regs->ip, (void *)regs->ip);
+	} else {
+		pr_emerg("MSR access error: RDMSR from 0x%x at rIP: 0x%lx (%pS)\n",
+			 (unsigned int)regs->cx, regs->ip, (void *)regs->ip);
+	}
 
 	show_stack_regs(regs);
 
@@ -387,8 +389,6 @@
 
 	while (true)
 		cpu_relax();
-
-	return true;
 }
 
 /* MSR access wrappers used for error injection */
@@ -420,32 +420,13 @@
 	 */
 	asm volatile("1: rdmsr\n"
 		     "2:\n"
-		     _ASM_EXTABLE_HANDLE(1b, 2b, ex_handler_rdmsr_fault)
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_RDMSR_IN_MCE)
 		     : EAX_EDX_RET(val, low, high) : "c" (msr));
 
 
 	return EAX_EDX_VAL(val, low, high);
 }
 
-__visible bool ex_handler_wrmsr_fault(const struct exception_table_entry *fixup,
-				      struct pt_regs *regs, int trapnr,
-				      unsigned long error_code,
-				      unsigned long fault_addr)
-{
-	pr_emerg("MSR access error: WRMSR to 0x%x (tried to write 0x%08x%08x) at rIP: 0x%lx (%pS)\n",
-		 (unsigned int)regs->cx, (unsigned int)regs->dx, (unsigned int)regs->ax,
-		  regs->ip, (void *)regs->ip);
-
-	show_stack_regs(regs);
-
-	panic("MCA architectural violation!\n");
-
-	while (true)
-		cpu_relax();
-
-	return true;
-}
-
 static noinstr void mce_wrmsrl(u32 msr, u64 v)
 {
 	u32 low, high;
@@ -470,7 +451,7 @@
 	/* See comment in mce_rdmsrl() */
 	asm volatile("1: wrmsr\n"
 		     "2:\n"
-		     _ASM_EXTABLE_HANDLE(1b, 2b, ex_handler_wrmsr_fault)
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_WRMSR_IN_MCE)
 		     : : "c" (msr), "a"(low), "d" (high) : "memory");
 }
 
@@ -682,13 +663,13 @@
 /*
  * Read ADDR and MISC registers.
  */
-static void mce_read_aux(struct mce *m, int i)
+static noinstr void mce_read_aux(struct mce *m, int i)
 {
 	if (m->status & MCI_STATUS_MISCV)
-		m->misc = mce_rdmsrl(msr_ops.misc(i));
+		m->misc = mce_rdmsrl(mca_msr_reg(i, MCA_MISC));
 
 	if (m->status & MCI_STATUS_ADDRV) {
-		m->addr = mce_rdmsrl(msr_ops.addr(i));
+		m->addr = mce_rdmsrl(mca_msr_reg(i, MCA_ADDR));
 
 		/*
 		 * Mask the reported address by the reported granularity.
@@ -758,7 +739,7 @@
 		m.bank = i;
 
 		barrier();
-		m.status = mce_rdmsrl(msr_ops.status(i));
+		m.status = mce_rdmsrl(mca_msr_reg(i, MCA_STATUS));
 
 		/* If this entry is not valid, ignore it */
 		if (!(m.status & MCI_STATUS_VAL))
@@ -826,7 +807,7 @@
 		/*
 		 * Clear state for this bank.
 		 */
-		mce_wrmsrl(msr_ops.status(i), 0);
+		mce_wrmsrl(mca_msr_reg(i, MCA_STATUS), 0);
 	}
 
 	/*
@@ -851,7 +832,7 @@
 	int i;
 
 	for (i = 0; i < this_cpu_read(mce_num_banks); i++) {
-		m->status = mce_rdmsrl(msr_ops.status(i));
+		m->status = mce_rdmsrl(mca_msr_reg(i, MCA_STATUS));
 		if (!(m->status & MCI_STATUS_VAL))
 			continue;
 
@@ -1072,10 +1053,13 @@
  * Synchronize between CPUs after main scanning loop.
  * This invokes the bulk of the Monarch processing.
  */
-static int mce_end(int order)
+static noinstr int mce_end(int order)
 {
-	int ret = -1;
 	u64 timeout = (u64)mca_cfg.monarch_timeout * NSEC_PER_USEC;
+	int ret = -1;
+
+	/* Allow instrumentation around external facilities. */
+	instrumentation_begin();
 
 	if (!timeout)
 		goto reset;
@@ -1119,7 +1103,8 @@
 		/*
 		 * Don't reset anything. That's done by the Monarch.
 		 */
-		return 0;
+		ret = 0;
+		goto out;
 	}
 
 	/*
@@ -1135,6 +1120,10 @@
 	 * Let others run again.
 	 */
 	atomic_set(&mce_executing, 0);
+
+out:
+	instrumentation_end();
+
 	return ret;
 }
 
@@ -1144,7 +1133,7 @@
 
 	for (i = 0; i < this_cpu_read(mce_num_banks); i++) {
 		if (test_bit(i, toclear))
-			mce_wrmsrl(msr_ops.status(i), 0);
+			mce_wrmsrl(mca_msr_reg(i, MCA_STATUS), 0);
 	}
 }
 
@@ -1203,7 +1192,7 @@
 		m->addr = 0;
 		m->bank = i;
 
-		m->status = mce_rdmsrl(msr_ops.status(i));
+		m->status = mce_rdmsrl(mca_msr_reg(i, MCA_STATUS));
 		if (!(m->status & MCI_STATUS_VAL))
 			continue;
 
@@ -1280,10 +1269,12 @@
 
 	/*
 	 * -EHWPOISON from memory_failure() means that it already sent SIGBUS
-	 * to the current process with the proper error info, so no need to
-	 * send SIGBUS here again.
+	 * to the current process with the proper error info,
+	 * -EOPNOTSUPP means hwpoison_filter() filtered the error event,
+	 *
+	 * In both cases, no further processing is required.
 	 */
-	if (ret == -EHWPOISON)
+	if (ret == -EHWPOISON || ret == -EOPNOTSUPP)
 		return;
 
 	if (p->mce_vaddr != (void __user *)-1l) {
@@ -1454,6 +1445,14 @@
 	if (worst != MCE_AR_SEVERITY && !kill_current_task)
 		goto out;
 
+	/*
+	 * Enable instrumentation around the external facilities like
+	 * task_work_add() (via queue_task_work()), fixup_exception() etc.
+	 * For now, that is. Fixing this properly would need a lot more involved
+	 * reorganization.
+	 */
+	instrumentation_begin();
+
 	/* Fault was in user mode and we need to take some action */
 	if ((m.cs & 3) == 3) {
 		/* If this triggers there is no way to recover. Die hard. */
@@ -1479,6 +1478,9 @@
 		if (m.kflags & MCE_IN_KERNEL_COPYIN)
 			queue_task_work(&m, msg, kill_current_task);
 	}
+
+	instrumentation_end();
+
 out:
 	mce_wrmsrl(MSR_IA32_MCG_STATUS, 0);
 }
@@ -1687,8 +1689,8 @@
 
 		if (!b->init)
 			continue;
-		wrmsrl(msr_ops.ctl(i), b->ctl);
-		wrmsrl(msr_ops.status(i), 0);
+		wrmsrl(mca_msr_reg(i, MCA_CTL), b->ctl);
+		wrmsrl(mca_msr_reg(i, MCA_STATUS), 0);
 	}
 }
 
@@ -1714,7 +1716,7 @@
 		if (!b->init)
 			continue;
 
-		rdmsrl(msr_ops.ctl(i), msrval);
+		rdmsrl(mca_msr_reg(i, MCA_CTL), msrval);
 		b->init = !!msrval;
 	}
 }
@@ -1871,13 +1873,6 @@
 		mce_flags.succor	 = !!cpu_has(c, X86_FEATURE_SUCCOR);
 		mce_flags.smca		 = !!cpu_has(c, X86_FEATURE_SMCA);
 		mce_flags.amd_threshold	 = 1;
-
-		if (mce_flags.smca) {
-			msr_ops.ctl	= smca_ctl_reg;
-			msr_ops.status	= smca_status_reg;
-			msr_ops.addr	= smca_addr_reg;
-			msr_ops.misc	= smca_misc_reg;
-		}
 	}
 }
 
@@ -2253,7 +2248,7 @@
 		struct mce_bank *b = &mce_banks[i];
 
 		if (b->init)
-			wrmsrl(msr_ops.ctl(i), 0);
+			wrmsrl(mca_msr_reg(i, MCA_CTL), 0);
 	}
 	return;
 }
@@ -2323,6 +2318,7 @@
 {
 	mce_timer_delete_all();
 	on_each_cpu(mce_cpu_restart, NULL, 1);
+	mce_schedule_work();
 }
 
 /* Toggle features for corrected errors */
@@ -2386,12 +2382,14 @@
 		return -EINVAL;
 
 	b = &per_cpu(mce_banks_array, s->id)[bank];
-
 	if (!b->init)
 		return -ENODEV;
 
 	b->ctl = new;
+
+	mutex_lock(&mce_sysfs_mutex);
 	mce_restart();
+	mutex_unlock(&mce_sysfs_mutex);
 
 	return size;
 }
@@ -2605,7 +2603,7 @@
 		struct mce_bank *b = &mce_banks[i];
 
 		if (b->init)
-			wrmsrl(msr_ops.ctl(i), b->ctl);
+			wrmsrl(mca_msr_reg(i, MCA_CTL), b->ctl);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/inject.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/inject.c
@@ -350,7 +350,7 @@
 	char buf[MAX_FLAG_OPT_SIZE], *__buf;
 	int err;
 
-	if (cnt > MAX_FLAG_OPT_SIZE)
+	if (!cnt || cnt > MAX_FLAG_OPT_SIZE)
 		return -EINVAL;
 
 	if (copy_from_user(&buf, ubuf, cnt))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/intel.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/intel.c
@@ -470,46 +470,6 @@
 	wrmsrl(MSR_IA32_MCG_EXT_CTL, val);
 }
 
-static void intel_ppin_init(struct cpuinfo_x86 *c)
-{
-	unsigned long long val;
-
-	/*
-	 * Even if testing the presence of the MSR would be enough, we don't
-	 * want to risk the situation where other models reuse this MSR for
-	 * other purposes.
-	 */
-	switch (c->x86_model) {
-	case INTEL_FAM6_IVYBRIDGE_X:
-	case INTEL_FAM6_HASWELL_X:
-	case INTEL_FAM6_BROADWELL_D:
-	case INTEL_FAM6_BROADWELL_X:
-	case INTEL_FAM6_SKYLAKE_X:
-	case INTEL_FAM6_ICELAKE_X:
-	case INTEL_FAM6_SAPPHIRERAPIDS_X:
-	case INTEL_FAM6_XEON_PHI_KNL:
-	case INTEL_FAM6_XEON_PHI_KNM:
-
-		if (rdmsrl_safe(MSR_PPIN_CTL, &val))
-			return;
-
-		if ((val & 3UL) == 1UL) {
-			/* PPIN locked in disabled mode */
-			return;
-		}
-
-		/* If PPIN is disabled, try to enable */
-		if (!(val & 2UL)) {
-			wrmsrl_safe(MSR_PPIN_CTL,  val | 2UL);
-			rdmsrl_safe(MSR_PPIN_CTL, &val);
-		}
-
-		/* Is the enable bit set? */
-		if (val & 2UL)
-			set_cpu_cap(c, X86_FEATURE_INTEL_PPIN);
-	}
-}
-
 /*
  * Enable additional error logs from the integrated
  * memory controller on processors that support this.
@@ -534,7 +494,6 @@
 {
 	intel_init_cmci();
 	intel_init_lmce();
-	intel_ppin_init(c);
 	intel_imc_init(c);
 }
 
@@ -547,12 +506,13 @@
 {
 	struct cpuinfo_x86 *c = &boot_cpu_data;
 
-	/* MCE errata HSD131, HSM142, HSW131, BDM48, and HSM142 */
+	/* MCE errata HSD131, HSM142, HSW131, BDM48, HSM142 and SKX37 */
 	if ((c->x86 == 6) &&
 	    ((c->x86_model == INTEL_FAM6_HASWELL) ||
 	     (c->x86_model == INTEL_FAM6_HASWELL_L) ||
 	     (c->x86_model == INTEL_FAM6_BROADWELL) ||
-	     (c->x86_model == INTEL_FAM6_HASWELL_G)) &&
+	     (c->x86_model == INTEL_FAM6_HASWELL_G) ||
+	     (c->x86_model == INTEL_FAM6_SKYLAKE_X)) &&
 	    (m->bank == 0) &&
 	    ((m->status & 0xa0000000ffffffff) == 0x80000000000f0005))
 		return true;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/internal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/internal.h
@@ -61,7 +61,7 @@
 static inline void intel_init_cmci(void) { }
 static inline void intel_init_lmce(void) { }
 static inline void intel_clear_lmce(void) { }
-static inline bool intel_filter_mce(struct mce *m) { return false; };
+static inline bool intel_filter_mce(struct mce *m) { return false; }
 #endif
 
 void mce_timer_kick(unsigned long interval);
@@ -168,14 +168,14 @@
 
 extern struct mce_vendor_flags mce_flags;
 
-struct mca_msr_regs {
-	u32 (*ctl)	(int bank);
-	u32 (*status)	(int bank);
-	u32 (*addr)	(int bank);
-	u32 (*misc)	(int bank);
+enum mca_msr {
+	MCA_CTL,
+	MCA_STATUS,
+	MCA_ADDR,
+	MCA_MISC,
 };
 
-extern struct mca_msr_regs msr_ops;
+u32 mca_msr_reg(int bank, enum mca_msr reg);
 
 /* Decide whether to add MCE record to MCE event pool or filter it out. */
 extern bool filter_mce(struct mce *m);
@@ -183,17 +183,7 @@
 #ifdef CONFIG_X86_MCE_AMD
 extern bool amd_filter_mce(struct mce *m);
 #else
-static inline bool amd_filter_mce(struct mce *m)			{ return false; };
+static inline bool amd_filter_mce(struct mce *m) { return false; }
 #endif
 
-__visible bool ex_handler_rdmsr_fault(const struct exception_table_entry *fixup,
-				      struct pt_regs *regs, int trapnr,
-				      unsigned long error_code,
-				      unsigned long fault_addr);
-
-__visible bool ex_handler_wrmsr_fault(const struct exception_table_entry *fixup,
-				      struct pt_regs *regs, int trapnr,
-				      unsigned long error_code,
-				      unsigned long fault_addr);
-
 #endif /* __X86_MCE_INTERNAL_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mce/severity.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mce/severity.c
@@ -265,25 +265,25 @@
  */
 static int error_context(struct mce *m, struct pt_regs *regs)
 {
-	enum handler_type t;
-
 	if ((m->cs & 3) == 3)
 		return IN_USER;
 	if (!mc_recoverable(m->mcgstatus))
 		return IN_KERNEL;
 
-	t = ex_get_fault_handler_type(m->ip);
-	if (t == EX_HANDLER_FAULT) {
-		m->kflags |= MCE_IN_KERNEL_RECOV;
-		return IN_KERNEL_RECOV;
-	}
-	if (t == EX_HANDLER_UACCESS && regs && is_copy_from_user(regs)) {
-		m->kflags |= MCE_IN_KERNEL_RECOV;
+	switch (ex_get_fixup_type(m->ip)) {
+	case EX_TYPE_UACCESS:
+	case EX_TYPE_COPY:
+		if (!regs || !is_copy_from_user(regs))
+			return IN_KERNEL;
 		m->kflags |= MCE_IN_KERNEL_COPYIN;
+		fallthrough;
+	case EX_TYPE_FAULT_MCE_SAFE:
+	case EX_TYPE_DEFAULT_MCE_SAFE:
+		m->kflags |= MCE_IN_KERNEL_RECOV;
 		return IN_KERNEL_RECOV;
+	default:
+		return IN_KERNEL;
 	}
-
-	return IN_KERNEL;
 }
 
 static int mce_severity_amd_smca(struct mce *m, enum context err_ctx)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/microcode/amd.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/microcode/amd.c
@@ -55,7 +55,9 @@
 };
 
 static u32 ucode_new_rev;
-static u8 amd_ucode_patch[PATCH_MAX_SIZE];
+
+/* One blob per node. */
+static u8 amd_ucode_patch[MAX_NUMNODES][PATCH_MAX_SIZE];
 
 /*
  * Microcode patch container file is prepended to the initrd in cpio
@@ -428,7 +430,7 @@
 	patch	= (u8 (*)[PATCH_MAX_SIZE])__pa_nodebug(&amd_ucode_patch);
 #else
 	new_rev = &ucode_new_rev;
-	patch	= &amd_ucode_patch;
+	patch	= &amd_ucode_patch[0];
 #endif
 
 	desc.cpuid_1_eax = cpuid_1_eax;
@@ -440,7 +442,13 @@
 		return ret;
 
 	native_rdmsr(MSR_AMD64_PATCH_LEVEL, rev, dummy);
-	if (rev >= mc->hdr.patch_id)
+
+	/*
+	 * Allow application of the same revision to pick up SMT-specific
+	 * changes even if the revision of the other SMT thread is already
+	 * up-to-date.
+	 */
+	if (rev > mc->hdr.patch_id)
 		return ret;
 
 	if (!__apply_microcode_amd(mc)) {
@@ -522,8 +530,12 @@
 
 	native_rdmsr(MSR_AMD64_PATCH_LEVEL, rev, dummy);
 
-	/* Check whether we have saved a new patch already: */
-	if (*new_rev && rev < mc->hdr.patch_id) {
+	/*
+	 * Check whether a new patch has been saved already. Also, allow application of
+	 * the same revision in order to pick up SMT-thread-specific configuration even
+	 * if the sibling SMT thread already has an up-to-date revision.
+	 */
+	if (*new_rev && rev <= mc->hdr.patch_id) {
 		if (!__apply_microcode_amd(mc)) {
 			*new_rev = mc->hdr.patch_id;
 			return;
@@ -537,8 +549,7 @@
 	apply_microcode_early_amd(cpuid_1_eax, cp.data, cp.size, false);
 }
 
-static enum ucode_state
-load_microcode_amd(bool save, u8 family, const u8 *data, size_t size);
+static enum ucode_state load_microcode_amd(u8 family, const u8 *data, size_t size);
 
 int __init save_microcode_in_initrd_amd(unsigned int cpuid_1_eax)
 {
@@ -556,19 +567,19 @@
 	if (!desc.mc)
 		return -EINVAL;
 
-	ret = load_microcode_amd(true, x86_family(cpuid_1_eax), desc.data, desc.size);
+	ret = load_microcode_amd(x86_family(cpuid_1_eax), desc.data, desc.size);
 	if (ret > UCODE_UPDATED)
 		return -EINVAL;
 
 	return 0;
 }
 
-void reload_ucode_amd(void)
+void reload_ucode_amd(unsigned int cpu)
 {
-	struct microcode_amd *mc;
 	u32 rev, dummy __always_unused;
+	struct microcode_amd *mc;
 
-	mc = (struct microcode_amd *)amd_ucode_patch;
+	mc = (struct microcode_amd *)amd_ucode_patch[cpu_to_node(cpu)];
 
 	rdmsr(MSR_AMD64_PATCH_LEVEL, rev, dummy);
 
@@ -688,7 +699,7 @@
 	rdmsr(MSR_AMD64_PATCH_LEVEL, rev, dummy);
 
 	/* need to apply patch? */
-	if (rev >= mc_amd->hdr.patch_id) {
+	if (rev > mc_amd->hdr.patch_id) {
 		ret = UCODE_OK;
 		goto out;
 	}
@@ -782,6 +793,7 @@
 		kfree(patch);
 		return -EINVAL;
 	}
+	patch->size = *patch_size;
 
 	mc_hdr      = (struct microcode_header_amd *)(fw + SECTION_HDR_SIZE);
 	proc_id     = mc_hdr->processor_rev_id;
@@ -833,9 +845,10 @@
 	return UCODE_OK;
 }
 
-static enum ucode_state
-load_microcode_amd(bool save, u8 family, const u8 *data, size_t size)
+static enum ucode_state load_microcode_amd(u8 family, const u8 *data, size_t size)
 {
+	struct cpuinfo_x86 *c;
+	unsigned int nid, cpu;
 	struct ucode_patch *p;
 	enum ucode_state ret;
 
@@ -848,22 +861,22 @@
 		return ret;
 	}
 
-	p = find_patch(0);
-	if (!p) {
-		return ret;
-	} else {
-		if (boot_cpu_data.microcode >= p->patch_id)
-			return ret;
+	for_each_node_with_cpus(nid) {
+		cpu = cpumask_first(cpumask_of_node(nid));
+		c = &cpu_data(cpu);
+
+		p = find_patch(cpu);
+		if (!p)
+			continue;
 
-		ret = UCODE_NEW;
-	}
+		if (c->microcode >= p->patch_id)
+			continue;
 
-	/* save BSP's matching patch for early load */
-	if (!save)
-		return ret;
+		ret = UCODE_NEW;
 
-	memset(amd_ucode_patch, 0, PATCH_MAX_SIZE);
-	memcpy(amd_ucode_patch, p->data, min_t(u32, ksize(p->data), PATCH_MAX_SIZE));
+		memset(&amd_ucode_patch[nid], 0, PATCH_MAX_SIZE);
+		memcpy(&amd_ucode_patch[nid], p->data, min_t(u32, p->size, PATCH_MAX_SIZE));
+	}
 
 	return ret;
 }
@@ -889,12 +902,11 @@
 {
 	char fw_name[36] = "amd-ucode/microcode_amd.bin";
 	struct cpuinfo_x86 *c = &cpu_data(cpu);
-	bool bsp = c->cpu_index == boot_cpu_data.cpu_index;
 	enum ucode_state ret = UCODE_NFOUND;
 	const struct firmware *fw;
 
 	/* reload ucode container only on the boot cpu */
-	if (!refresh_fw || !bsp)
+	if (!refresh_fw)
 		return UCODE_OK;
 
 	if (c->x86 >= 0x15)
@@ -909,7 +921,7 @@
 	if (!verify_container(fw->data, fw->size, false))
 		goto fw_release;
 
-	ret = load_microcode_amd(bsp, c->x86, fw->data, fw->size);
+	ret = load_microcode_amd(c->x86, fw->data, fw->size);
 
  fw_release:
 	release_firmware(fw);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/microcode/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/microcode/core.c
@@ -315,7 +315,7 @@
 #endif
 }
 
-void reload_early_microcode(void)
+void reload_early_microcode(unsigned int cpu)
 {
 	int vendor, family;
 
@@ -329,7 +329,7 @@
 		break;
 	case X86_VENDOR_AMD:
 		if (family >= 0x10)
-			reload_ucode_amd();
+			reload_ucode_amd(cpu);
 		break;
 	default:
 		break;
@@ -390,101 +390,10 @@
 	return ret;
 }
 
-#ifdef CONFIG_MICROCODE_OLD_INTERFACE
-static int do_microcode_update(const void __user *buf, size_t size)
-{
-	int error = 0;
-	int cpu;
-
-	for_each_online_cpu(cpu) {
-		struct ucode_cpu_info *uci = ucode_cpu_info + cpu;
-		enum ucode_state ustate;
-
-		if (!uci->valid)
-			continue;
-
-		ustate = microcode_ops->request_microcode_user(cpu, buf, size);
-		if (ustate == UCODE_ERROR) {
-			error = -1;
-			break;
-		} else if (ustate == UCODE_NEW) {
-			apply_microcode_on_target(cpu);
-		}
-	}
-
-	return error;
-}
-
-static int microcode_open(struct inode *inode, struct file *file)
-{
-	return capable(CAP_SYS_RAWIO) ? stream_open(inode, file) : -EPERM;
-}
-
-static ssize_t microcode_write(struct file *file, const char __user *buf,
-			       size_t len, loff_t *ppos)
-{
-	ssize_t ret = -EINVAL;
-	unsigned long nr_pages = totalram_pages();
-
-	if ((len >> PAGE_SHIFT) > nr_pages) {
-		pr_err("too much data (max %ld pages)\n", nr_pages);
-		return ret;
-	}
-
-	cpus_read_lock();
-	mutex_lock(&microcode_mutex);
-
-	if (do_microcode_update(buf, len) == 0)
-		ret = (ssize_t)len;
-
-	if (ret > 0)
-		perf_check_microcode();
-
-	mutex_unlock(&microcode_mutex);
-	cpus_read_unlock();
-
-	return ret;
-}
-
-static const struct file_operations microcode_fops = {
-	.owner			= THIS_MODULE,
-	.write			= microcode_write,
-	.open			= microcode_open,
-	.llseek		= no_llseek,
-};
-
-static struct miscdevice microcode_dev = {
-	.minor			= MICROCODE_MINOR,
-	.name			= "microcode",
-	.nodename		= "cpu/microcode",
-	.fops			= &microcode_fops,
-};
-
-static int __init microcode_dev_init(void)
-{
-	int error;
-
-	error = misc_register(&microcode_dev);
-	if (error) {
-		pr_err("can't misc_register on minor=%d\n", MICROCODE_MINOR);
-		return error;
-	}
-
-	return 0;
-}
-
-static void __exit microcode_dev_exit(void)
-{
-	misc_deregister(&microcode_dev);
-}
-#else
-#define microcode_dev_init()	0
-#define microcode_dev_exit()	do { } while (0)
-#endif
-
 /* fake device for request_firmware */
 static struct platform_device	*microcode_pdev;
 
+#ifdef CONFIG_MICROCODE_LATE_LOADING
 /*
  * Late loading dance. Why the heavy-handed stomp_machine effort?
  *
@@ -599,16 +508,27 @@
  */
 static int microcode_reload_late(void)
 {
-	int ret;
+	int old = boot_cpu_data.microcode, ret;
+	struct cpuinfo_x86 prev_info;
 
 	atomic_set(&late_cpus_in,  0);
 	atomic_set(&late_cpus_out, 0);
 
-	ret = stop_machine_cpuslocked(__reload_late, NULL, cpu_online_mask);
-	if (ret == 0)
-		microcode_check();
+	/*
+	 * Take a snapshot before the microcode update in order to compare and
+	 * check whether any bits changed after an update.
+	 */
+	store_cpu_caps(&prev_info);
 
-	pr_info("Reload completed, microcode revision: 0x%x\n", boot_cpu_data.microcode);
+	ret = stop_machine_cpuslocked(__reload_late, NULL, cpu_online_mask);
+	if (!ret) {
+		pr_info("Reload succeeded, microcode revision: 0x%x -> 0x%x\n",
+			old, boot_cpu_data.microcode);
+		microcode_check(&prev_info);
+	} else {
+		pr_info("Reload failed, current microcode revision: 0x%x\n",
+			boot_cpu_data.microcode);
+	}
 
 	return ret;
 }
@@ -652,6 +572,9 @@
 	return ret;
 }
 
+static DEVICE_ATTR_WO(reload);
+#endif
+
 static ssize_t version_show(struct device *dev,
 			struct device_attribute *attr, char *buf)
 {
@@ -668,7 +591,6 @@
 	return sprintf(buf, "0x%x\n", uci->cpu_sig.pf);
 }
 
-static DEVICE_ATTR_WO(reload);
 static DEVICE_ATTR(version, 0444, version_show, NULL);
 static DEVICE_ATTR(processor_flags, 0444, pf_show, NULL);
 
@@ -775,9 +697,9 @@
 };
 
 /**
- * mc_bp_resume - Update boot CPU microcode during resume.
+ * microcode_bsp_resume - Update boot CPU microcode during resume.
  */
-static void mc_bp_resume(void)
+void microcode_bsp_resume(void)
 {
 	int cpu = smp_processor_id();
 	struct ucode_cpu_info *uci = ucode_cpu_info + cpu;
@@ -785,11 +707,11 @@
 	if (uci->valid && uci->mc)
 		microcode_ops->apply_microcode(cpu);
 	else if (!uci->mc)
-		reload_early_microcode();
+		reload_early_microcode(cpu);
 }
 
 static struct syscore_ops mc_syscore_ops = {
-	.resume			= mc_bp_resume,
+	.resume			= microcode_bsp_resume,
 };
 
 static int mc_cpu_starting(unsigned int cpu)
@@ -821,7 +743,9 @@
 }
 
 static struct attribute *cpu_root_microcode_attrs[] = {
+#ifdef CONFIG_MICROCODE_LATE_LOADING
 	&dev_attr_reload.attr,
+#endif
 	NULL
 };
 
@@ -873,10 +797,6 @@
 		goto out_driver;
 	}
 
-	error = microcode_dev_init();
-	if (error)
-		goto out_ucode_group;
-
 	register_syscore_ops(&mc_syscore_ops);
 	cpuhp_setup_state_nocalls(CPUHP_AP_MICROCODE_LOADER, "x86/microcode:starting",
 				  mc_cpu_starting, NULL);
@@ -887,10 +807,6 @@
 
 	return 0;
 
- out_ucode_group:
-	sysfs_remove_group(&cpu_subsys.dev_root->kobj,
-			   &cpu_root_microcode_group);
-
  out_driver:
 	cpus_read_lock();
 	mutex_lock(&microcode_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/microcode/intel.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/microcode/intel.c
@@ -659,7 +659,6 @@
 	else
 		iup = &intel_ucode_patch;
 
-reget:
 	if (!*iup) {
 		patch = __load_ucode_intel(&uci);
 		if (!patch)
@@ -670,12 +669,7 @@
 
 	uci.mc = *iup;
 
-	if (apply_microcode_early(&uci, true)) {
-		/* Mixed-silicon system? Try to refetch the proper patch: */
-		*iup = NULL;
-
-		goto reget;
-	}
+	apply_microcode_early(&uci, true);
 }
 
 static struct microcode_intel *find_patch(struct ucode_cpu_info *uci)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mshyperv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mshyperv.c
@@ -16,7 +16,6 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/kexec.h>
-#include <linux/i8253.h>
 #include <linux/random.h>
 #include <asm/processor.h>
 #include <asm/hypervisor.h>
@@ -79,7 +78,7 @@
 	inc_irq_stat(hyperv_stimer0_count);
 	if (hv_stimer0_handler)
 		hv_stimer0_handler();
-	add_interrupt_randomness(HYPERV_STIMER0_VECTOR, 0);
+	add_interrupt_randomness(HYPERV_STIMER0_VECTOR);
 	ack_APIC_irq();
 
 	set_irq_regs(old_regs);
@@ -150,6 +149,63 @@
 	hyperv_cleanup();
 }
 #endif /* CONFIG_KEXEC_CORE */
+
+static u64 hv_ref_counter_at_suspend;
+static void (*old_save_sched_clock_state)(void);
+static void (*old_restore_sched_clock_state)(void);
+
+/*
+ * Hyper-V clock counter resets during hibernation. Save and restore clock
+ * offset during suspend/resume, while also considering the time passed
+ * before suspend. This is to make sure that sched_clock using hv tsc page
+ * based clocksource, proceeds from where it left off during suspend and
+ * it shows correct time for the timestamps of kernel messages after resume.
+ */
+static void save_hv_clock_tsc_state(void)
+{
+	hv_ref_counter_at_suspend = hv_read_reference_counter();
+}
+
+static void restore_hv_clock_tsc_state(void)
+{
+	/*
+	 * Adjust the offsets used by hv tsc clocksource to
+	 * account for the time spent before hibernation.
+	 * adjusted value = reference counter (time) at suspend
+	 *                - reference counter (time) now.
+	 */
+	hv_adj_sched_clock_offset(hv_ref_counter_at_suspend - hv_read_reference_counter());
+}
+
+/*
+ * Functions to override save_sched_clock_state and restore_sched_clock_state
+ * functions of x86_platform. The Hyper-V clock counter is reset during
+ * suspend-resume and the offset used to measure time needs to be
+ * corrected, post resume.
+ */
+static void hv_save_sched_clock_state(void)
+{
+	old_save_sched_clock_state();
+	save_hv_clock_tsc_state();
+}
+
+static void hv_restore_sched_clock_state(void)
+{
+	restore_hv_clock_tsc_state();
+	old_restore_sched_clock_state();
+}
+
+static void __init x86_setup_ops_for_tsc_pg_clock(void)
+{
+	if (!(ms_hyperv.features & HV_MSR_REFERENCE_TSC_AVAILABLE))
+		return;
+
+	old_save_sched_clock_state = x86_platform.save_sched_clock_state;
+	x86_platform.save_sched_clock_state = hv_save_sched_clock_state;
+
+	old_restore_sched_clock_state = x86_platform.restore_sched_clock_state;
+	x86_platform.restore_sched_clock_state = hv_restore_sched_clock_state;
+}
 #endif /* CONFIG_HYPERV */
 
 static uint32_t  __init ms_hyperv_platform(void)
@@ -163,12 +219,22 @@
 	cpuid(HYPERV_CPUID_VENDOR_AND_MAX_FUNCTIONS,
 	      &eax, &hyp_signature[0], &hyp_signature[1], &hyp_signature[2]);
 
-	if (eax >= HYPERV_CPUID_MIN &&
-	    eax <= HYPERV_CPUID_MAX &&
-	    !memcmp("Microsoft Hv", hyp_signature, 12))
-		return HYPERV_CPUID_VENDOR_AND_MAX_FUNCTIONS;
+	if (eax < HYPERV_CPUID_MIN || eax > HYPERV_CPUID_MAX ||
+	    memcmp("Microsoft Hv", hyp_signature, 12))
+		return 0;
 
-	return 0;
+	/* HYPERCALL and VP_INDEX MSRs are mandatory for all features. */
+	eax = cpuid_eax(HYPERV_CPUID_FEATURES);
+	if (!(eax & HV_MSR_HYPERCALL_AVAILABLE)) {
+		pr_warn("x86/hyperv: HYPERCALL MSR not available.\n");
+		return 0;
+	}
+	if (!(eax & HV_MSR_VP_INDEX_AVAILABLE)) {
+		pr_warn("x86/hyperv: VP_INDEX MSR not available.\n");
+		return 0;
+	}
+
+	return HYPERV_CPUID_VENDOR_AND_MAX_FUNCTIONS;
 }
 
 static unsigned char hv_get_nmi_reason(void)
@@ -279,12 +345,16 @@
 	 * To mirror what Windows does we should extract CPU management
 	 * features and use the ReservedIdentityBit to detect if Linux is the
 	 * root partition. But that requires negotiating CPU management
-	 * interface (a process to be finalized).
+	 * interface (a process to be finalized). For now, use the privilege
+	 * flag as the indicator for running as root.
 	 *
-	 * For now, use the privilege flag as the indicator for running as
-	 * root.
+	 * Hyper-V should never specify running as root and as a Confidential
+	 * VM. But to protect against a compromised/malicious Hyper-V trying
+	 * to exploit root behavior to expose Confidential VM memory, ignore
+	 * the root partition setting if also a Confidential VM.
 	 */
-	if (cpuid_ebx(HYPERV_CPUID_FEATURES) & HV_CPU_MANAGEMENT) {
+	if ((ms_hyperv.priv_high & HV_CPU_MANAGEMENT) &&
+	    !(ms_hyperv.priv_high & HV_ISOLATION)) {
 		hv_root_partition = true;
 		pr_info("Hyper-V: running as root partition\n");
 	}
@@ -308,6 +378,7 @@
 	    ms_hyperv.misc_features & HV_FEATURE_FREQUENCY_MSRS_AVAILABLE) {
 		x86_platform.calibrate_tsc = hv_get_tsc_khz;
 		x86_platform.calibrate_cpu = hv_get_tsc_khz;
+		setup_force_cpu_cap(X86_FEATURE_TSC_KNOWN_FREQ);
 	}
 
 	if (ms_hyperv.priv_high & HV_ISOLATION) {
@@ -373,16 +444,6 @@
 	if (efi_enabled(EFI_BOOT))
 		x86_platform.get_nmi_reason = hv_get_nmi_reason;
 
-	/*
-	 * Hyper-V VMs have a PIT emulation quirk such that zeroing the
-	 * counter register during PIT shutdown restarts the PIT. So it
-	 * continues to interrupt @18.2 HZ. Setting i8253_clear_counter
-	 * to false tells pit_shutdown() not to zero the counter so that
-	 * the PIT really is shutdown. Generation 2 VMs don't have a PIT,
-	 * and setting this value has no effect.
-	 */
-	i8253_clear_counter_on_shutdown = false;
-
 #if IS_ENABLED(CONFIG_HYPERV)
 	/*
 	 * Setup the hook to get control post apic initialization.
@@ -423,6 +484,7 @@
 
 	/* Register Hyper-V specific clocksource */
 	hv_init_clocksource();
+	x86_setup_ops_for_tsc_pg_clock();
 #endif
 	/*
 	 * TSC should be marked as unstable only after Hyper-V
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mtrr/cleanup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mtrr/cleanup.c
@@ -173,7 +173,7 @@
 
 static void __init
 set_var_mtrr(unsigned int reg, unsigned long basek, unsigned long sizek,
-	     unsigned char type, unsigned int address_bits)
+	     unsigned char type)
 {
 	u32 base_lo, base_hi, mask_lo, mask_hi;
 	u64 base, mask;
@@ -183,7 +183,7 @@
 		return;
 	}
 
-	mask = (1ULL << address_bits) - 1;
+	mask = (1ULL << boot_cpu_data.x86_phys_bits) - 1;
 	mask &= ~((((u64)sizek) << 10) - 1);
 
 	base = ((u64)basek) << 10;
@@ -209,7 +209,7 @@
 	range_state[reg].type = type;
 }
 
-static void __init set_var_mtrr_all(unsigned int address_bits)
+static void __init set_var_mtrr_all(void)
 {
 	unsigned long basek, sizek;
 	unsigned char type;
@@ -220,7 +220,7 @@
 		sizek = range_state[reg].size_pfn << (PAGE_SHIFT - 10);
 		type = range_state[reg].type;
 
-		set_var_mtrr(reg, basek, sizek, type, address_bits);
+		set_var_mtrr(reg, basek, sizek, type);
 	}
 }
 
@@ -680,7 +680,7 @@
 	return index_good;
 }
 
-int __init mtrr_cleanup(unsigned address_bits)
+int __init mtrr_cleanup(void)
 {
 	unsigned long x_remove_base, x_remove_size;
 	unsigned long base, size, def, dummy;
@@ -742,7 +742,7 @@
 		mtrr_print_out_one_result(i);
 
 		if (!result[i].bad) {
-			set_var_mtrr_all(address_bits);
+			set_var_mtrr_all();
 			pr_debug("New variable MTRRs\n");
 			print_out_mtrr_range_state();
 			return 1;
@@ -786,7 +786,7 @@
 		gran_size = result[i].gran_sizek;
 		gran_size <<= 10;
 		x86_setup_var_mtrrs(range, nr_range, chunk_size, gran_size);
-		set_var_mtrr_all(address_bits);
+		set_var_mtrr_all();
 		pr_debug("New variable MTRRs\n");
 		print_out_mtrr_range_state();
 		return 1;
@@ -802,7 +802,7 @@
 	return 0;
 }
 #else
-int __init mtrr_cleanup(unsigned address_bits)
+int __init mtrr_cleanup(void)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mtrr/generic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mtrr/generic.c
@@ -37,6 +37,16 @@
 struct mtrr_state_type mtrr_state;
 EXPORT_SYMBOL_GPL(mtrr_state);
 
+static u64 size_or_mask, size_and_mask;
+
+void __init mtrr_set_mask(void)
+{
+	unsigned int phys_addr = boot_cpu_data.x86_phys_bits;
+
+	size_or_mask = ~GENMASK_ULL(phys_addr - PAGE_SHIFT - 1, 0);
+	size_and_mask = ~size_or_mask & GENMASK_ULL(39, 20);
+}
+
 /*
  * BIOS is expected to clear MtrrFixDramModEn bit, see for example
  * "BIOS and Kernel Developer's Guide for the AMD Athlon 64 and AMD
@@ -424,7 +434,7 @@
 	}
 	pr_debug("MTRR variable ranges %sabled:\n",
 		 mtrr_state.enabled & MTRR_STATE_MTRR_ENABLED ? "en" : "dis");
-	high_width = (__ffs64(size_or_mask) - (32 - PAGE_SHIFT) + 3) / 4;
+	high_width = (boot_cpu_data.x86_phys_bits - (32 - PAGE_SHIFT) + 3) / 4;
 
 	for (i = 0; i < num_var_ranges; ++i) {
 		if (mtrr_state.var_ranges[i].mask_lo & (1 << 11))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mtrr/mtrr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mtrr/mtrr.c
@@ -68,7 +68,6 @@
 unsigned int mtrr_usage_table[MTRR_MAX_VAR_RANGES];
 static DEFINE_MUTEX(mtrr_mutex);
 
-u64 size_or_mask, size_and_mask;
 static bool mtrr_aps_delayed_init;
 
 static const struct mtrr_ops *mtrr_ops[X86_VENDOR_NUM] __ro_after_init;
@@ -676,78 +675,34 @@
 
 int __initdata changed_by_mtrr_cleanup;
 
-#define SIZE_OR_MASK_BITS(n)  (~((1ULL << ((n) - PAGE_SHIFT)) - 1))
 /**
- * mtrr_bp_init - initialize mtrrs on the boot CPU
+ * mtrr_bp_init - initialize MTRRs on the boot CPU
  *
  * This needs to be called early; before any of the other CPUs are
  * initialized (i.e. before smp_init()).
- *
  */
 void __init mtrr_bp_init(void)
 {
-	u32 phys_addr;
-
 	init_ifs();
 
-	phys_addr = 32;
+	mtrr_set_mask();
 
-	if (boot_cpu_has(X86_FEATURE_MTRR)) {
+	if (cpu_feature_enabled(X86_FEATURE_MTRR)) {
 		mtrr_if = &generic_mtrr_ops;
-		size_or_mask = SIZE_OR_MASK_BITS(36);
-		size_and_mask = 0x00f00000;
-		phys_addr = 36;
-
-		/*
-		 * This is an AMD specific MSR, but we assume(hope?) that
-		 * Intel will implement it too when they extend the address
-		 * bus of the Xeon.
-		 */
-		if (cpuid_eax(0x80000000) >= 0x80000008) {
-			phys_addr = cpuid_eax(0x80000008) & 0xff;
-			/* CPUID workaround for Intel 0F33/0F34 CPU */
-			if (boot_cpu_data.x86_vendor == X86_VENDOR_INTEL &&
-			    boot_cpu_data.x86 == 0xF &&
-			    boot_cpu_data.x86_model == 0x3 &&
-			    (boot_cpu_data.x86_stepping == 0x3 ||
-			     boot_cpu_data.x86_stepping == 0x4))
-				phys_addr = 36;
-
-			size_or_mask = SIZE_OR_MASK_BITS(phys_addr);
-			size_and_mask = ~size_or_mask & 0xfffff00000ULL;
-		} else if (boot_cpu_data.x86_vendor == X86_VENDOR_CENTAUR &&
-			   boot_cpu_data.x86 == 6) {
-			/*
-			 * VIA C* family have Intel style MTRRs,
-			 * but don't support PAE
-			 */
-			size_or_mask = SIZE_OR_MASK_BITS(32);
-			size_and_mask = 0;
-			phys_addr = 32;
-		}
 	} else {
 		switch (boot_cpu_data.x86_vendor) {
 		case X86_VENDOR_AMD:
-			if (cpu_feature_enabled(X86_FEATURE_K6_MTRR)) {
-				/* Pre-Athlon (K6) AMD CPU MTRRs */
+			/* Pre-Athlon (K6) AMD CPU MTRRs */
+			if (cpu_feature_enabled(X86_FEATURE_K6_MTRR))
 				mtrr_if = mtrr_ops[X86_VENDOR_AMD];
-				size_or_mask = SIZE_OR_MASK_BITS(32);
-				size_and_mask = 0;
-			}
 			break;
 		case X86_VENDOR_CENTAUR:
-			if (cpu_feature_enabled(X86_FEATURE_CENTAUR_MCR)) {
+			if (cpu_feature_enabled(X86_FEATURE_CENTAUR_MCR))
 				mtrr_if = mtrr_ops[X86_VENDOR_CENTAUR];
-				size_or_mask = SIZE_OR_MASK_BITS(32);
-				size_and_mask = 0;
-			}
 			break;
 		case X86_VENDOR_CYRIX:
-			if (cpu_feature_enabled(X86_FEATURE_CYRIX_ARR)) {
+			if (cpu_feature_enabled(X86_FEATURE_CYRIX_ARR))
 				mtrr_if = mtrr_ops[X86_VENDOR_CYRIX];
-				size_or_mask = SIZE_OR_MASK_BITS(32);
-				size_and_mask = 0;
-			}
 			break;
 		default:
 			break;
@@ -765,7 +720,7 @@
 			if (mtrr_enabled())
 				mtrr_bp_pat_init();
 
-			if (mtrr_cleanup(phys_addr)) {
+			if (mtrr_cleanup()) {
 				changed_by_mtrr_cleanup = 1;
 				mtrr_if->set_all();
 			}
@@ -816,7 +771,7 @@
 {
 	int first_cpu;
 
-	if (!mtrr_enabled())
+	if (!mtrr_enabled() || !mtrr_state.have_fixed)
 		return;
 
 	first_cpu = cpumask_first(cpu_online_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/mtrr/mtrr.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/mtrr/mtrr.h
@@ -57,7 +57,6 @@
 
 extern void __init set_mtrr_ops(const struct mtrr_ops *ops);
 
-extern u64 size_or_mask, size_and_mask;
 extern const struct mtrr_ops *mtrr_if;
 
 #define is_cpu(vnd)	(mtrr_if && mtrr_if->vendor == X86_VENDOR_##vnd)
@@ -67,6 +66,7 @@
 extern u64 mtrr_tom2;
 extern struct mtrr_state_type mtrr_state;
 
+void mtrr_set_mask(void);
 void mtrr_state_warn(void);
 const char *mtrr_attrib_to_str(int x);
 void mtrr_wrmsr(unsigned, unsigned, unsigned);
@@ -77,4 +77,4 @@
 int centaur_init_mtrr(void);
 
 extern int changed_by_mtrr_cleanup;
-extern int mtrr_cleanup(unsigned address_bits);
+extern int mtrr_cleanup(void);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/resctrl/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/resctrl/core.c
@@ -66,9 +66,6 @@
 			.rid			= RDT_RESOURCE_L3,
 			.name			= "L3",
 			.cache_level		= 3,
-			.cache = {
-				.min_cbm_bits	= 1,
-			},
 			.domains		= domain_init(RDT_RESOURCE_L3),
 			.parse_ctrlval		= parse_cbm,
 			.format_str		= "%d=%0*x",
@@ -83,9 +80,6 @@
 			.rid			= RDT_RESOURCE_L2,
 			.name			= "L2",
 			.cache_level		= 2,
-			.cache = {
-				.min_cbm_bits	= 1,
-			},
 			.domains		= domain_init(RDT_RESOURCE_L2),
 			.parse_ctrlval		= parse_cbm,
 			.format_str		= "%d=%0*x",
@@ -181,7 +175,7 @@
 	return false;
 }
 
-static bool __get_mem_config_intel(struct rdt_resource *r)
+static __init bool __get_mem_config_intel(struct rdt_resource *r)
 {
 	struct rdt_hw_resource *hw_res = resctrl_to_arch_res(r);
 	union cpuid_0x10_3_eax eax;
@@ -216,7 +210,7 @@
 	return true;
 }
 
-static bool __rdt_get_mem_config_amd(struct rdt_resource *r)
+static __init bool __rdt_get_mem_config_amd(struct rdt_resource *r)
 {
 	struct rdt_hw_resource *hw_res = resctrl_to_arch_res(r);
 	union cpuid_0x10_3_eax eax;
@@ -877,6 +871,7 @@
 			r->cache.arch_has_sparse_bitmaps = false;
 			r->cache.arch_has_empty_bitmaps = false;
 			r->cache.arch_has_per_cpu_cfg = false;
+			r->cache.min_cbm_bits = 1;
 		} else if (r->rid == RDT_RESOURCE_MBA) {
 			hw_res->msr_base = MSR_IA32_MBA_THRTL_BASE;
 			hw_res->msr_update = mba_wrmsr_intel;
@@ -897,6 +892,7 @@
 			r->cache.arch_has_sparse_bitmaps = true;
 			r->cache.arch_has_empty_bitmaps = true;
 			r->cache.arch_has_per_cpu_cfg = true;
+			r->cache.min_cbm_bits = 0;
 		} else if (r->rid == RDT_RESOURCE_MBA) {
 			hw_res->msr_base = MSR_IA32_MBA_BW_BASE;
 			hw_res->msr_update = mba_wrmsr_amd;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/resctrl/ctrlmondata.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/resctrl/ctrlmondata.c
@@ -27,10 +27,10 @@
  * hardware. The allocated bandwidth percentage is rounded to the next
  * control step available on the hardware.
  */
-static bool bw_validate(char *buf, unsigned long *data, struct rdt_resource *r)
+static bool bw_validate(char *buf, u32 *data, struct rdt_resource *r)
 {
-	unsigned long bw;
 	int ret;
+	u32 bw;
 
 	/*
 	 * Only linear delay values is supported for current Intel SKUs.
@@ -40,16 +40,21 @@
 		return false;
 	}
 
-	ret = kstrtoul(buf, 10, &bw);
+	ret = kstrtou32(buf, 10, &bw);
 	if (ret) {
-		rdt_last_cmd_printf("Non-decimal digit in MB value %s\n", buf);
+		rdt_last_cmd_printf("Invalid MB value %s\n", buf);
 		return false;
 	}
 
-	if ((bw < r->membw.min_bw || bw > r->default_ctrl) &&
-	    !is_mba_sc(r)) {
-		rdt_last_cmd_printf("MB value %ld out of range [%d,%d]\n", bw,
-				    r->membw.min_bw, r->default_ctrl);
+	/* Nothing else to do if software controller is enabled. */
+	if (is_mba_sc(r)) {
+		*data = bw;
+		return true;
+	}
+
+	if (bw < r->membw.min_bw || bw > r->default_ctrl) {
+		rdt_last_cmd_printf("MB value %u out of range [%d,%d]\n",
+				    bw, r->membw.min_bw, r->default_ctrl);
 		return false;
 	}
 
@@ -62,7 +67,7 @@
 {
 	struct resctrl_staged_config *cfg;
 	struct rdt_resource *r = s->res;
-	unsigned long bw_val;
+	u32 bw_val;
 
 	cfg = &d->staged_config[s->conf_type];
 	if (cfg->have_new_ctrl) {
@@ -353,7 +358,6 @@
 {
 	struct resctrl_schema *s;
 	struct rdtgroup *rdtgrp;
-	struct rdt_domain *dom;
 	struct rdt_resource *r;
 	char *tok, *resname;
 	int ret = 0;
@@ -382,10 +386,7 @@
 		goto out;
 	}
 
-	list_for_each_entry(s, &resctrl_schema_all, list) {
-		list_for_each_entry(dom, &s->res->domains, list)
-			memset(dom->staged_config, 0, sizeof(dom->staged_config));
-	}
+	rdt_staged_configs_clear();
 
 	while ((tok = strsep(&buf, "\n")) != NULL) {
 		resname = strim(strsep(&tok, ":"));
@@ -422,6 +423,7 @@
 	}
 
 out:
+	rdt_staged_configs_clear();
 	rdtgroup_kn_unlock(of->kn);
 	cpus_read_unlock();
 	return ret ?: nbytes;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/resctrl/internal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/resctrl/internal.h
@@ -550,5 +550,6 @@
 void __check_limbo(struct rdt_domain *d, bool force_free);
 void rdt_domain_reconfigure_cdp(struct rdt_resource *r);
 void __init thread_throttle_mode_init(void);
+void rdt_staged_configs_clear(void);
 
 #endif /* _ASM_X86_RESCTRL_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/resctrl/pseudo_lock.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/resctrl/pseudo_lock.c
@@ -420,6 +420,7 @@
 	struct pseudo_lock_region *plr = rdtgrp->plr;
 	u32 rmid_p, closid_p;
 	unsigned long i;
+	u64 saved_msr;
 #ifdef CONFIG_KASAN
 	/*
 	 * The registers used for local register variables are also used
@@ -463,6 +464,7 @@
 	 * the buffer and evict pseudo-locked memory read earlier from the
 	 * cache.
 	 */
+	saved_msr = __rdmsr(MSR_MISC_FEATURE_CONTROL);
 	__wrmsr(MSR_MISC_FEATURE_CONTROL, prefetch_disable_bits, 0x0);
 	closid_p = this_cpu_read(pqr_state.cur_closid);
 	rmid_p = this_cpu_read(pqr_state.cur_rmid);
@@ -514,7 +516,7 @@
 	__wrmsr(IA32_PQR_ASSOC, rmid_p, closid_p);
 
 	/* Re-enable the hardware prefetcher(s) */
-	wrmsr(MSR_MISC_FEATURE_CONTROL, 0x0, 0x0);
+	wrmsrl(MSR_MISC_FEATURE_CONTROL, saved_msr);
 	local_irq_enable();
 
 	plr->thread_done = 1;
@@ -871,6 +873,7 @@
 static int measure_cycles_lat_fn(void *_plr)
 {
 	struct pseudo_lock_region *plr = _plr;
+	u32 saved_low, saved_high;
 	unsigned long i;
 	u64 start, end;
 	void *mem_r;
@@ -879,6 +882,7 @@
 	/*
 	 * Disable hardware prefetchers.
 	 */
+	rdmsr(MSR_MISC_FEATURE_CONTROL, saved_low, saved_high);
 	wrmsr(MSR_MISC_FEATURE_CONTROL, prefetch_disable_bits, 0x0);
 	mem_r = READ_ONCE(plr->kmem);
 	/*
@@ -895,7 +899,7 @@
 		end = rdtsc_ordered();
 		trace_pseudo_lock_mem_latency((u32)(end - start));
 	}
-	wrmsr(MSR_MISC_FEATURE_CONTROL, 0x0, 0x0);
+	wrmsr(MSR_MISC_FEATURE_CONTROL, saved_low, saved_high);
 	local_irq_enable();
 	plr->thread_done = 1;
 	wake_up_interruptible(&plr->lock_thread_wq);
@@ -940,6 +944,7 @@
 	u64 hits_before = 0, hits_after = 0, miss_before = 0, miss_after = 0;
 	struct perf_event *miss_event, *hit_event;
 	int hit_pmcnum, miss_pmcnum;
+	u32 saved_low, saved_high;
 	unsigned int line_size;
 	unsigned int size;
 	unsigned long i;
@@ -973,6 +978,7 @@
 	/*
 	 * Disable hardware prefetchers.
 	 */
+	rdmsr(MSR_MISC_FEATURE_CONTROL, saved_low, saved_high);
 	wrmsr(MSR_MISC_FEATURE_CONTROL, prefetch_disable_bits, 0x0);
 
 	/* Initialize rest of local variables */
@@ -1031,7 +1037,7 @@
 	 */
 	rmb();
 	/* Re-enable hardware prefetchers */
-	wrmsr(MSR_MISC_FEATURE_CONTROL, 0x0, 0x0);
+	wrmsr(MSR_MISC_FEATURE_CONTROL, saved_low, saved_high);
 	local_irq_enable();
 out_hit:
 	perf_event_release_kernel(hit_event);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/resctrl/rdtgroup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/resctrl/rdtgroup.c
@@ -78,6 +78,19 @@
 	va_end(ap);
 }
 
+void rdt_staged_configs_clear(void)
+{
+	struct rdt_resource *r;
+	struct rdt_domain *dom;
+
+	lockdep_assert_held(&rdtgroup_mutex);
+
+	for_each_alloc_capable_rdt_resource(r) {
+		list_for_each_entry(dom, &r->domains, list)
+			memset(dom->staged_config, 0, sizeof(dom->staged_config));
+	}
+}
+
 /*
  * Trivial allocator for CLOSIDs. Since h/w only supports a small number,
  * we can keep a bitmap of free CLOSIDs in a single integer.
@@ -314,7 +327,7 @@
 	 * executing task might have its own closid selected. Just reuse
 	 * the context switch code.
 	 */
-	resctrl_sched_in();
+	resctrl_sched_in(current);
 }
 
 /*
@@ -535,7 +548,7 @@
 	 * Otherwise, the MSR is updated when the task is scheduled in.
 	 */
 	if (task == current)
-		resctrl_sched_in();
+		resctrl_sched_in(task);
 }
 
 static void update_task_closid_rmid(struct task_struct *t)
@@ -580,8 +593,10 @@
 	/*
 	 * Ensure the task's closid and rmid are written before determining if
 	 * the task is current that will decide if it will be interrupted.
+	 * This pairs with the full barrier between the rq->curr update and
+	 * resctrl_sched_in() during context switch.
 	 */
-	barrier();
+	smp_mb();
 
 	/*
 	 * By now, the task's closid and rmid are set. If the task is current
@@ -716,11 +731,15 @@
 static void show_rdt_tasks(struct rdtgroup *r, struct seq_file *s)
 {
 	struct task_struct *p, *t;
+	pid_t pid;
 
 	rcu_read_lock();
 	for_each_process_thread(p, t) {
-		if (is_closid_match(t, r) || is_rmid_match(t, r))
-			seq_printf(s, "%d\n", t->pid);
+		if (is_closid_match(t, r) || is_rmid_match(t, r)) {
+			pid = task_pid_vnr(t);
+			if (pid)
+				seq_printf(s, "%d\n", pid);
+		}
 	}
 	rcu_read_unlock();
 }
@@ -2364,6 +2383,14 @@
 			WRITE_ONCE(t->rmid, to->mon.rmid);
 
 			/*
+			 * Order the closid/rmid stores above before the loads
+			 * in task_curr(). This pairs with the full barrier
+			 * between the rq->curr update and resctrl_sched_in()
+			 * during context switch.
+			 */
+			smp_mb();
+
+			/*
 			 * If the task is on a CPU, set the CPU in the mask.
 			 * The detection is inaccurate as tasks might move or
 			 * schedule before the smp function call takes place.
@@ -2803,7 +2830,9 @@
 {
 	struct resctrl_schema *s;
 	struct rdt_resource *r;
-	int ret;
+	int ret = 0;
+
+	rdt_staged_configs_clear();
 
 	list_for_each_entry(s, &resctrl_schema_all, list) {
 		r = s->res;
@@ -2812,20 +2841,22 @@
 		} else {
 			ret = rdtgroup_init_cat(s, rdtgrp->closid);
 			if (ret < 0)
-				return ret;
+				goto out;
 		}
 
 		ret = resctrl_arch_update_domains(r, rdtgrp->closid);
 		if (ret < 0) {
 			rdt_last_cmd_puts("Failed to initialize allocations\n");
-			return ret;
+			goto out;
 		}
 
 	}
 
 	rdtgrp->mode = RDT_MODE_SHAREABLE;
 
-	return 0;
+out:
+	rdt_staged_configs_clear();
+	return ret;
 }
 
 static int mkdir_rdt_prepare(struct kernfs_node *parent_kn,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/scattered.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/scattered.c
@@ -26,6 +26,8 @@
 static const struct cpuid_bit cpuid_bits[] = {
 	{ X86_FEATURE_APERFMPERF,       CPUID_ECX,  0, 0x00000006, 0 },
 	{ X86_FEATURE_EPB,		CPUID_ECX,  3, 0x00000006, 0 },
+	{ X86_FEATURE_RRSBA_CTRL,	CPUID_EDX,  2, 0x00000007, 2 },
+	{ X86_FEATURE_BHI_CTRL,		CPUID_EDX,  4, 0x00000007, 2 },
 	{ X86_FEATURE_CQM_LLC,		CPUID_EDX,  1, 0x0000000f, 0 },
 	{ X86_FEATURE_CQM_OCCUP_LLC,	CPUID_EDX,  0, 0x0000000f, 1 },
 	{ X86_FEATURE_CQM_MBM_TOTAL,	CPUID_EDX,  1, 0x0000000f, 1 },
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/sgx/driver.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/sgx/driver.c
@@ -150,13 +150,15 @@
 	u64 xfrm_mask;
 	int ret;
 
-	if (!cpu_feature_enabled(X86_FEATURE_SGX_LC))
+	if (!cpu_feature_enabled(X86_FEATURE_SGX_LC)) {
+		pr_info("SGX disabled: SGX launch control CPU feature is not available, /dev/sgx_enclave disabled.\n");
 		return -ENODEV;
+	}
 
 	cpuid_count(SGX_CPUID, 0, &eax, &ebx, &ecx, &edx);
 
 	if (!(eax & 1))  {
-		pr_err("SGX disabled: SGX1 instruction support not available.\n");
+		pr_info("SGX disabled: SGX1 instruction support not available, /dev/sgx_enclave disabled.\n");
 		return -ENODEV;
 	}
 
@@ -173,8 +175,10 @@
 	}
 
 	ret = misc_register(&sgx_dev_enclave);
-	if (ret)
+	if (ret) {
+		pr_info("SGX disabled: Unable to register the /dev/sgx_enclave driver (%d).\n", ret);
 		return ret;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/sgx/encl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/sgx/encl.c
@@ -12,6 +12,116 @@
 #include "encls.h"
 #include "sgx.h"
 
+#define PCMDS_PER_PAGE (PAGE_SIZE / sizeof(struct sgx_pcmd))
+/*
+ * 32 PCMD entries share a PCMD page. PCMD_FIRST_MASK is used to
+ * determine the page index associated with the first PCMD entry
+ * within a PCMD page.
+ */
+#define PCMD_FIRST_MASK GENMASK(4, 0)
+
+/**
+ * reclaimer_writing_to_pcmd() - Query if any enclave page associated with
+ *                               a PCMD page is in process of being reclaimed.
+ * @encl:        Enclave to which PCMD page belongs
+ * @start_addr:  Address of enclave page using first entry within the PCMD page
+ *
+ * When an enclave page is reclaimed some Paging Crypto MetaData (PCMD) is
+ * stored. The PCMD data of a reclaimed enclave page contains enough
+ * information for the processor to verify the page at the time
+ * it is loaded back into the Enclave Page Cache (EPC).
+ *
+ * The backing storage to which enclave pages are reclaimed is laid out as
+ * follows:
+ * Encrypted enclave pages:SECS page:PCMD pages
+ *
+ * Each PCMD page contains the PCMD metadata of
+ * PAGE_SIZE/sizeof(struct sgx_pcmd) enclave pages.
+ *
+ * A PCMD page can only be truncated if it is (a) empty, and (b) not in the
+ * process of getting data (and thus soon being non-empty). (b) is tested with
+ * a check if an enclave page sharing the PCMD page is in the process of being
+ * reclaimed.
+ *
+ * The reclaimer sets the SGX_ENCL_PAGE_BEING_RECLAIMED flag when it
+ * intends to reclaim that enclave page - it means that the PCMD page
+ * associated with that enclave page is about to get some data and thus
+ * even if the PCMD page is empty, it should not be truncated.
+ *
+ * Context: Enclave mutex (&sgx_encl->lock) must be held.
+ * Return: 1 if the reclaimer is about to write to the PCMD page
+ *         0 if the reclaimer has no intention to write to the PCMD page
+ */
+static int reclaimer_writing_to_pcmd(struct sgx_encl *encl,
+				     unsigned long start_addr)
+{
+	int reclaimed = 0;
+	int i;
+
+	/*
+	 * PCMD_FIRST_MASK is based on number of PCMD entries within
+	 * PCMD page being 32.
+	 */
+	BUILD_BUG_ON(PCMDS_PER_PAGE != 32);
+
+	for (i = 0; i < PCMDS_PER_PAGE; i++) {
+		struct sgx_encl_page *entry;
+		unsigned long addr;
+
+		addr = start_addr + i * PAGE_SIZE;
+
+		/*
+		 * Stop when reaching the SECS page - it does not
+		 * have a page_array entry and its reclaim is
+		 * started and completed with enclave mutex held so
+		 * it does not use the SGX_ENCL_PAGE_BEING_RECLAIMED
+		 * flag.
+		 */
+		if (addr == encl->base + encl->size)
+			break;
+
+		entry = xa_load(&encl->page_array, PFN_DOWN(addr));
+		if (!entry)
+			continue;
+
+		/*
+		 * VA page slot ID uses same bit as the flag so it is important
+		 * to ensure that the page is not already in backing store.
+		 */
+		if (entry->epc_page &&
+		    (entry->desc & SGX_ENCL_PAGE_BEING_RECLAIMED)) {
+			reclaimed = 1;
+			break;
+		}
+	}
+
+	return reclaimed;
+}
+
+/*
+ * Calculate byte offset of a PCMD struct associated with an enclave page. PCMD's
+ * follow right after the EPC data in the backing storage. In addition to the
+ * visible enclave pages, there's one extra page slot for SECS, before PCMD
+ * structs.
+ */
+static inline pgoff_t sgx_encl_get_backing_page_pcmd_offset(struct sgx_encl *encl,
+							    unsigned long page_index)
+{
+	pgoff_t epc_end_off = encl->size + sizeof(struct sgx_secs);
+
+	return epc_end_off + page_index * sizeof(struct sgx_pcmd);
+}
+
+/*
+ * Free a page from the backing storage in the given page index.
+ */
+static inline void sgx_encl_truncate_backing_page(struct sgx_encl *encl, unsigned long page_index)
+{
+	struct inode *inode = file_inode(encl->backing);
+
+	shmem_truncate_range(inode, PFN_PHYS(page_index), PFN_PHYS(page_index) + PAGE_SIZE - 1);
+}
+
 /*
  * ELDU: Load an EPC page as unblocked. For more info, see "OS Management of EPC
  * Pages" in the SDM.
@@ -22,9 +132,12 @@
 {
 	unsigned long va_offset = encl_page->desc & SGX_ENCL_PAGE_VA_OFFSET_MASK;
 	struct sgx_encl *encl = encl_page->encl;
+	pgoff_t page_index, page_pcmd_off;
+	unsigned long pcmd_first_page;
 	struct sgx_pageinfo pginfo;
 	struct sgx_backing b;
-	pgoff_t page_index;
+	bool pcmd_page_empty;
+	u8 *pcmd_page;
 	int ret;
 
 	if (secs_page)
@@ -32,14 +145,21 @@
 	else
 		page_index = PFN_DOWN(encl->size);
 
-	ret = sgx_encl_get_backing(encl, page_index, &b);
+	/*
+	 * Address of enclave page using the first entry within the PCMD page.
+	 */
+	pcmd_first_page = PFN_PHYS(page_index & ~PCMD_FIRST_MASK) + encl->base;
+
+	page_pcmd_off = sgx_encl_get_backing_page_pcmd_offset(encl, page_index);
+
+	ret = sgx_encl_lookup_backing(encl, page_index, &b);
 	if (ret)
 		return ret;
 
 	pginfo.addr = encl_page->desc & PAGE_MASK;
 	pginfo.contents = (unsigned long)kmap_atomic(b.contents);
-	pginfo.metadata = (unsigned long)kmap_atomic(b.pcmd) +
-			  b.pcmd_offset;
+	pcmd_page = kmap_atomic(b.pcmd);
+	pginfo.metadata = (unsigned long)pcmd_page + b.pcmd_offset;
 
 	if (secs_page)
 		pginfo.secs = (u64)sgx_get_epc_virt_addr(secs_page);
@@ -55,10 +175,32 @@
 		ret = -EFAULT;
 	}
 
-	kunmap_atomic((void *)(unsigned long)(pginfo.metadata - b.pcmd_offset));
+	memset(pcmd_page + b.pcmd_offset, 0, sizeof(struct sgx_pcmd));
+	set_page_dirty(b.pcmd);
+
+	/*
+	 * The area for the PCMD in the page was zeroed above.  Check if the
+	 * whole page is now empty meaning that all PCMD's have been zeroed:
+	 */
+	pcmd_page_empty = !memchr_inv(pcmd_page, 0, PAGE_SIZE);
+
+	kunmap_atomic(pcmd_page);
 	kunmap_atomic((void *)(unsigned long)pginfo.contents);
 
-	sgx_encl_put_backing(&b, false);
+	get_page(b.pcmd);
+	sgx_encl_put_backing(&b);
+
+	sgx_encl_truncate_backing_page(encl, page_index);
+
+	if (pcmd_page_empty && !reclaimer_writing_to_pcmd(encl, pcmd_first_page)) {
+		sgx_encl_truncate_backing_page(encl, PFN_DOWN(page_pcmd_off));
+		pcmd_page = kmap_atomic(b.pcmd);
+		if (memchr_inv(pcmd_page, 0, PAGE_SIZE))
+			pr_warn("PCMD page not empty after truncate.\n");
+		kunmap_atomic(pcmd_page);
+	}
+
+	put_page(b.pcmd);
 
 	return ret;
 }
@@ -90,25 +232,10 @@
 	return epc_page;
 }
 
-static struct sgx_encl_page *sgx_encl_load_page(struct sgx_encl *encl,
-						unsigned long addr,
-						unsigned long vm_flags)
+static struct sgx_encl_page *__sgx_encl_load_page(struct sgx_encl *encl,
+						  struct sgx_encl_page *entry)
 {
-	unsigned long vm_prot_bits = vm_flags & (VM_READ | VM_WRITE | VM_EXEC);
 	struct sgx_epc_page *epc_page;
-	struct sgx_encl_page *entry;
-
-	entry = xa_load(&encl->page_array, PFN_DOWN(addr));
-	if (!entry)
-		return ERR_PTR(-EFAULT);
-
-	/*
-	 * Verify that the faulted page has equal or higher build time
-	 * permissions than the VMA permissions (i.e. the subset of {VM_READ,
-	 * VM_WRITE, VM_EXECUTE} in vma->vm_flags).
-	 */
-	if ((entry->vm_max_prot_bits & vm_prot_bits) != vm_prot_bits)
-		return ERR_PTR(-EFAULT);
 
 	/* Entry successfully located. */
 	if (entry->epc_page) {
@@ -134,6 +261,40 @@
 	return entry;
 }
 
+static struct sgx_encl_page *sgx_encl_load_page_in_vma(struct sgx_encl *encl,
+						       unsigned long addr,
+						       unsigned long vm_flags)
+{
+	unsigned long vm_prot_bits = vm_flags & (VM_READ | VM_WRITE | VM_EXEC);
+	struct sgx_encl_page *entry;
+
+	entry = xa_load(&encl->page_array, PFN_DOWN(addr));
+	if (!entry)
+		return ERR_PTR(-EFAULT);
+
+	/*
+	 * Verify that the page has equal or higher build time
+	 * permissions than the VMA permissions (i.e. the subset of {VM_READ,
+	 * VM_WRITE, VM_EXECUTE} in vma->vm_flags).
+	 */
+	if ((entry->vm_max_prot_bits & vm_prot_bits) != vm_prot_bits)
+		return ERR_PTR(-EFAULT);
+
+	return __sgx_encl_load_page(encl, entry);
+}
+
+struct sgx_encl_page *sgx_encl_load_page(struct sgx_encl *encl,
+					 unsigned long addr)
+{
+	struct sgx_encl_page *entry;
+
+	entry = xa_load(&encl->page_array, PFN_DOWN(addr));
+	if (!entry)
+		return ERR_PTR(-EFAULT);
+
+	return __sgx_encl_load_page(encl, entry);
+}
+
 static vm_fault_t sgx_vma_fault(struct vm_fault *vmf)
 {
 	unsigned long addr = (unsigned long)vmf->address;
@@ -155,7 +316,7 @@
 
 	mutex_lock(&encl->lock);
 
-	entry = sgx_encl_load_page(encl, addr, vma->vm_flags);
+	entry = sgx_encl_load_page_in_vma(encl, addr, vma->vm_flags);
 	if (IS_ERR(entry)) {
 		mutex_unlock(&encl->lock);
 
@@ -303,7 +464,7 @@
 	for ( ; ; ) {
 		mutex_lock(&encl->lock);
 
-		entry = sgx_encl_load_page(encl, addr, vm_flags);
+		entry = sgx_encl_load_page_in_vma(encl, addr, vm_flags);
 		if (PTR_ERR(entry) != -EBUSY)
 			break;
 
@@ -391,11 +552,15 @@
 void sgx_encl_release(struct kref *ref)
 {
 	struct sgx_encl *encl = container_of(ref, struct sgx_encl, refcount);
+	unsigned long max_page_index = PFN_DOWN(encl->base + encl->size - 1);
 	struct sgx_va_page *va_page;
 	struct sgx_encl_page *entry;
-	unsigned long index;
+	unsigned long count = 0;
 
-	xa_for_each(&encl->page_array, index, entry) {
+	XA_STATE(xas, &encl->page_array, PFN_DOWN(encl->base));
+
+	xas_lock(&xas);
+	xas_for_each(&xas, entry, max_page_index) {
 		if (entry->epc_page) {
 			/*
 			 * The page and its radix tree entry cannot be freed
@@ -410,7 +575,20 @@
 		}
 
 		kfree(entry);
+		/*
+		 * Invoke scheduler on every XA_CHECK_SCHED iteration
+		 * to prevent soft lockups.
+		 */
+		if (!(++count % XA_CHECK_SCHED)) {
+			xas_pause(&xas);
+			xas_unlock(&xas);
+
+			cond_resched();
+
+			xas_lock(&xas);
+		}
 	}
+	xas_unlock(&xas);
 
 	xa_destroy(&encl->page_array);
 
@@ -543,7 +721,7 @@
 
 	spin_lock(&encl->mm_lock);
 	list_add_rcu(&encl_mm->list, &encl->mm_list);
-	/* Pairs with smp_rmb() in sgx_reclaimer_block(). */
+	/* Pairs with smp_rmb() in sgx_zap_enclave_ptes(). */
 	smp_wmb();
 	encl->mm_list_version++;
 	spin_unlock(&encl->mm_lock);
@@ -574,10 +752,10 @@
  *   0 on success,
  *   -errno otherwise.
  */
-int sgx_encl_get_backing(struct sgx_encl *encl, unsigned long page_index,
+static int sgx_encl_get_backing(struct sgx_encl *encl, unsigned long page_index,
 			 struct sgx_backing *backing)
 {
-	pgoff_t pcmd_index = PFN_DOWN(encl->size) + 1 + (page_index >> 5);
+	pgoff_t page_pcmd_off = sgx_encl_get_backing_page_pcmd_offset(encl, page_index);
 	struct page *contents;
 	struct page *pcmd;
 
@@ -585,7 +763,7 @@
 	if (IS_ERR(contents))
 		return PTR_ERR(contents);
 
-	pcmd = sgx_encl_get_backing_page(encl, pcmd_index);
+	pcmd = sgx_encl_get_backing_page(encl, PFN_DOWN(page_pcmd_off));
 	if (IS_ERR(pcmd)) {
 		put_page(contents);
 		return PTR_ERR(pcmd);
@@ -594,25 +772,118 @@
 	backing->page_index = page_index;
 	backing->contents = contents;
 	backing->pcmd = pcmd;
-	backing->pcmd_offset =
-		(page_index & (PAGE_SIZE / sizeof(struct sgx_pcmd) - 1)) *
-		sizeof(struct sgx_pcmd);
+	backing->pcmd_offset = page_pcmd_off & (PAGE_SIZE - 1);
 
 	return 0;
 }
 
+/*
+ * When called from ksgxd, returns the mem_cgroup of a struct mm stored
+ * in the enclave's mm_list. When not called from ksgxd, just returns
+ * the mem_cgroup of the current task.
+ */
+static struct mem_cgroup *sgx_encl_get_mem_cgroup(struct sgx_encl *encl)
+{
+	struct mem_cgroup *memcg = NULL;
+	struct sgx_encl_mm *encl_mm;
+	int idx;
+
+	/*
+	 * If called from normal task context, return the mem_cgroup
+	 * of the current task's mm. The remainder of the handling is for
+	 * ksgxd.
+	 */
+	if (!current_is_ksgxd())
+		return get_mem_cgroup_from_mm(current->mm);
+
+	/*
+	 * Search the enclave's mm_list to find an mm associated with
+	 * this enclave to charge the allocation to.
+	 */
+	idx = srcu_read_lock(&encl->srcu);
+
+	list_for_each_entry_rcu(encl_mm, &encl->mm_list, list) {
+		if (!mmget_not_zero(encl_mm->mm))
+			continue;
+
+		memcg = get_mem_cgroup_from_mm(encl_mm->mm);
+
+		mmput_async(encl_mm->mm);
+
+		break;
+	}
+
+	srcu_read_unlock(&encl->srcu, idx);
+
+	/*
+	 * In the rare case that there isn't an mm associated with
+	 * the enclave, set memcg to the current active mem_cgroup.
+	 * This will be the root mem_cgroup if there is no active
+	 * mem_cgroup.
+	 */
+	if (!memcg)
+		return get_mem_cgroup_from_mm(NULL);
+
+	return memcg;
+}
+
 /**
- * sgx_encl_put_backing() - Unpin the backing storage
+ * sgx_encl_alloc_backing() - allocate a new backing storage page
+ * @encl:	an enclave pointer
+ * @page_index:	enclave page index
+ * @backing:	data for accessing backing storage for the page
+ *
+ * When called from ksgxd, sets the active memcg from one of the
+ * mms in the enclave's mm_list prior to any backing page allocation,
+ * in order to ensure that shmem page allocations are charged to the
+ * enclave.
+ *
+ * Return:
+ *   0 on success,
+ *   -errno otherwise.
+ */
+int sgx_encl_alloc_backing(struct sgx_encl *encl, unsigned long page_index,
+			   struct sgx_backing *backing)
+{
+	struct mem_cgroup *encl_memcg = sgx_encl_get_mem_cgroup(encl);
+	struct mem_cgroup *memcg = set_active_memcg(encl_memcg);
+	int ret;
+
+	ret = sgx_encl_get_backing(encl, page_index, backing);
+
+	set_active_memcg(memcg);
+	mem_cgroup_put(encl_memcg);
+
+	return ret;
+}
+
+/**
+ * sgx_encl_lookup_backing() - retrieve an existing backing storage page
+ * @encl:	an enclave pointer
+ * @page_index:	enclave page index
  * @backing:	data for accessing backing storage for the page
- * @do_write:	mark pages dirty
+ *
+ * Retrieve a backing page for loading data back into an EPC page with ELDU.
+ * It is the caller's responsibility to ensure that it is appropriate to use
+ * sgx_encl_lookup_backing() rather than sgx_encl_alloc_backing(). If lookup is
+ * not used correctly, this will cause an allocation which is not accounted for.
+ *
+ * Return:
+ *   0 on success,
+ *   -errno otherwise.
  */
-void sgx_encl_put_backing(struct sgx_backing *backing, bool do_write)
+int sgx_encl_lookup_backing(struct sgx_encl *encl, unsigned long page_index,
+			   struct sgx_backing *backing)
 {
-	if (do_write) {
-		set_page_dirty(backing->pcmd);
-		set_page_dirty(backing->contents);
-	}
+	return sgx_encl_get_backing(encl, page_index, backing);
+}
 
+/**
+ * sgx_encl_put_backing() - Unpin the backing storage
+ * @backing:	data for accessing backing storage for the page
+ */
+void sgx_encl_put_backing(struct sgx_backing *backing)
+{
 	put_page(backing->pcmd);
 	put_page(backing->contents);
 }
@@ -666,7 +937,52 @@
 }
 
 /**
+ * sgx_zap_enclave_ptes() - remove PTEs mapping the address from enclave
+ * @encl: the enclave
+ * @addr: page aligned pointer to single page for which PTEs will be removed
+ *
+ * Multiple VMAs may have an enclave page mapped. Remove the PTE mapping
+ * @addr from each VMA. Ensure that page fault handler is ready to handle
+ * new mappings of @addr before calling this function.
+ */
+void sgx_zap_enclave_ptes(struct sgx_encl *encl, unsigned long addr)
+{
+	unsigned long mm_list_version;
+	struct sgx_encl_mm *encl_mm;
+	struct vm_area_struct *vma;
+	int idx, ret;
+
+	do {
+		mm_list_version = encl->mm_list_version;
+
+		/* Pairs with smp_wmb() in sgx_encl_mm_add(). */
+		smp_rmb();
+
+		idx = srcu_read_lock(&encl->srcu);
+
+		list_for_each_entry_rcu(encl_mm, &encl->mm_list, list) {
+			if (!mmget_not_zero(encl_mm->mm))
+				continue;
+
+			mmap_read_lock(encl_mm->mm);
+
+			ret = sgx_encl_find(encl_mm->mm, addr, &vma);
+			if (!ret && encl == vma->vm_private_data)
+				zap_vma_ptes(vma, addr, PAGE_SIZE);
+
+			mmap_read_unlock(encl_mm->mm);
+
+			mmput_async(encl_mm->mm);
+		}
+
+		srcu_read_unlock(&encl->srcu, idx);
+	} while (unlikely(encl->mm_list_version != mm_list_version));
+}
+
+/**
  * sgx_alloc_va_page() - Allocate a Version Array (VA) page
+ * @reclaim: Reclaim EPC pages directly if none available. Enclave
+ *           mutex should not be held if this is set.
  *
  * Allocate a free EPC page and convert it to a Version Array (VA) page.
  *
@@ -674,12 +990,12 @@
  *   a VA page,
  *   -errno otherwise
  */
-struct sgx_epc_page *sgx_alloc_va_page(void)
+struct sgx_epc_page *sgx_alloc_va_page(bool reclaim)
 {
 	struct sgx_epc_page *epc_page;
 	int ret;
 
-	epc_page = sgx_alloc_epc_page(NULL, true);
+	epc_page = sgx_alloc_epc_page(NULL, reclaim);
 	if (IS_ERR(epc_page))
 		return ERR_CAST(epc_page);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/sgx/encl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/sgx/encl.h
@@ -103,18 +103,25 @@
 int sgx_encl_may_map(struct sgx_encl *encl, unsigned long start,
 		     unsigned long end, unsigned long vm_flags);
 
+bool current_is_ksgxd(void);
 void sgx_encl_release(struct kref *ref);
 int sgx_encl_mm_add(struct sgx_encl *encl, struct mm_struct *mm);
-int sgx_encl_get_backing(struct sgx_encl *encl, unsigned long page_index,
-			 struct sgx_backing *backing);
-void sgx_encl_put_backing(struct sgx_backing *backing, bool do_write);
+int sgx_encl_lookup_backing(struct sgx_encl *encl, unsigned long page_index,
+			    struct sgx_backing *backing);
+int sgx_encl_alloc_backing(struct sgx_encl *encl, unsigned long page_index,
+			   struct sgx_backing *backing);
+void sgx_encl_put_backing(struct sgx_backing *backing);
 int sgx_encl_test_and_clear_young(struct mm_struct *mm,
 				  struct sgx_encl_page *page);
-
-struct sgx_epc_page *sgx_alloc_va_page(void);
+void sgx_zap_enclave_ptes(struct sgx_encl *encl, unsigned long addr);
+struct sgx_epc_page *sgx_alloc_va_page(bool reclaim);
 unsigned int sgx_alloc_va_slot(struct sgx_va_page *va_page);
 void sgx_free_va_slot(struct sgx_va_page *va_page, unsigned int offset);
 bool sgx_va_page_full(struct sgx_va_page *va_page);
 void sgx_encl_free_epc_page(struct sgx_epc_page *page);
+struct sgx_encl_page *sgx_encl_load_page(struct sgx_encl *encl,
+					 unsigned long addr);
+struct sgx_va_page *sgx_encl_grow(struct sgx_encl *encl, bool reclaim);
+void sgx_encl_shrink(struct sgx_encl *encl, struct sgx_va_page *va_page);
 
 #endif /* _X86_ENCL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/sgx/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/sgx/ioctl.c
@@ -17,7 +17,7 @@
 #include "encl.h"
 #include "encls.h"
 
-static struct sgx_va_page *sgx_encl_grow(struct sgx_encl *encl)
+struct sgx_va_page *sgx_encl_grow(struct sgx_encl *encl, bool reclaim)
 {
 	struct sgx_va_page *va_page = NULL;
 	void *err;
@@ -30,7 +30,7 @@
 		if (!va_page)
 			return ERR_PTR(-ENOMEM);
 
-		va_page->epc_page = sgx_alloc_va_page();
+		va_page->epc_page = sgx_alloc_va_page(reclaim);
 		if (IS_ERR(va_page->epc_page)) {
 			err = ERR_CAST(va_page->epc_page);
 			kfree(va_page);
@@ -43,7 +43,7 @@
 	return va_page;
 }
 
-static void sgx_encl_shrink(struct sgx_encl *encl, struct sgx_va_page *va_page)
+void sgx_encl_shrink(struct sgx_encl *encl, struct sgx_va_page *va_page)
 {
 	encl->page_cnt--;
 
@@ -64,7 +64,14 @@
 	struct file *backing;
 	long ret;
 
-	va_page = sgx_encl_grow(encl);
+	/*
+	 * ECREATE would detect this too, but checking here also ensures
+	 * that the 'encl_size' calculations below can never overflow.
+	 */
+	if (!is_power_of_2(secs->size))
+		return -EINVAL;
+
+	va_page = sgx_encl_grow(encl, true);
 	if (IS_ERR(va_page))
 		return PTR_ERR(va_page);
 	else if (va_page)
@@ -306,7 +313,7 @@
 		return PTR_ERR(epc_page);
 	}
 
-	va_page = sgx_encl_grow(encl);
+	va_page = sgx_encl_grow(encl, true);
 	if (IS_ERR(va_page)) {
 		ret = PTR_ERR(va_page);
 		goto err_out_free;
@@ -372,6 +379,29 @@
 	return ret;
 }
 
+/*
+ * Ensure user provided offset and length values are valid for
+ * an enclave.
+ */
+static int sgx_validate_offset_length(struct sgx_encl *encl,
+				      unsigned long offset,
+				      unsigned long length)
+{
+	if (!IS_ALIGNED(offset, PAGE_SIZE))
+		return -EINVAL;
+
+	if (!length || !IS_ALIGNED(length, PAGE_SIZE))
+		return -EINVAL;
+
+	if (offset + length < offset)
+		return -EINVAL;
+
+	if (offset + length - PAGE_SIZE >= encl->size)
+		return -EINVAL;
+
+	return 0;
+}
+
 /**
  * sgx_ioc_enclave_add_pages() - The handler for %SGX_IOC_ENCLAVE_ADD_PAGES
  * @encl:       an enclave pointer
@@ -425,14 +455,10 @@
 	if (copy_from_user(&add_arg, arg, sizeof(add_arg)))
 		return -EFAULT;
 
-	if (!IS_ALIGNED(add_arg.offset, PAGE_SIZE) ||
-	    !IS_ALIGNED(add_arg.src, PAGE_SIZE))
-		return -EINVAL;
-
-	if (!add_arg.length || add_arg.length & (PAGE_SIZE - 1))
+	if (!IS_ALIGNED(add_arg.src, PAGE_SIZE))
 		return -EINVAL;
 
-	if (add_arg.offset + add_arg.length - PAGE_SIZE >= encl->size)
+	if (sgx_validate_offset_length(encl, add_arg.offset, add_arg.length))
 		return -EINVAL;
 
 	if (copy_from_user(&secinfo, (void __user *)add_arg.secinfo,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/sgx/main.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/sgx/main.c
@@ -28,8 +28,7 @@
 static LIST_HEAD(sgx_active_page_list);
 static DEFINE_SPINLOCK(sgx_reclaimer_lock);
 
-/* The free page list lock protected variables prepend the lock. */
-static unsigned long sgx_nr_free_pages;
+static atomic_long_t sgx_nr_free_pages = ATOMIC_LONG_INIT(0);
 
 /* Nodes with one or more EPC sections. */
 static nodemask_t sgx_numa_mask;
@@ -47,9 +46,13 @@
  * Reset post-kexec EPC pages to the uninitialized state. The pages are removed
  * from the input list, and made available for the page allocator. SECS pages
  * prepending their children in the input list are left intact.
+ *
+ * Return 0 when sanitization was successful or kthread was stopped, and the
+ * number of unsanitized pages otherwise.
  */
-static void __sgx_sanitize_pages(struct list_head *dirty_page_list)
+static unsigned long __sgx_sanitize_pages(struct list_head *dirty_page_list)
 {
+	unsigned long left_dirty = 0;
 	struct sgx_epc_page *page;
 	LIST_HEAD(dirty);
 	int ret;
@@ -57,7 +60,7 @@
 	/* dirty_page_list is thread-local, no need for a lock: */
 	while (!list_empty(dirty_page_list)) {
 		if (kthread_should_stop())
-			return;
+			return 0;
 
 		page = list_first_entry(dirty_page_list, struct sgx_epc_page, list);
 
@@ -72,12 +75,14 @@
 		} else {
 			/* The page is not yet clean - move to the dirty list. */
 			list_move_tail(&page->list, &dirty);
+			left_dirty++;
 		}
 
 		cond_resched();
 	}
 
 	list_splice(&dirty, dirty_page_list);
+	return left_dirty;
 }
 
 static bool sgx_reclaimer_age(struct sgx_epc_page *epc_page)
@@ -117,36 +122,9 @@
 	struct sgx_encl_page *page = epc_page->owner;
 	unsigned long addr = page->desc & PAGE_MASK;
 	struct sgx_encl *encl = page->encl;
-	unsigned long mm_list_version;
-	struct sgx_encl_mm *encl_mm;
-	struct vm_area_struct *vma;
-	int idx, ret;
-
-	do {
-		mm_list_version = encl->mm_list_version;
-
-		/* Pairs with smp_rmb() in sgx_encl_mm_add(). */
-		smp_rmb();
-
-		idx = srcu_read_lock(&encl->srcu);
-
-		list_for_each_entry_rcu(encl_mm, &encl->mm_list, list) {
-			if (!mmget_not_zero(encl_mm->mm))
-				continue;
-
-			mmap_read_lock(encl_mm->mm);
-
-			ret = sgx_encl_find(encl_mm->mm, addr, &vma);
-			if (!ret && encl == vma->vm_private_data)
-				zap_vma_ptes(vma, addr, PAGE_SIZE);
-
-			mmap_read_unlock(encl_mm->mm);
-
-			mmput_async(encl_mm->mm);
-		}
+	int ret;
 
-		srcu_read_unlock(&encl->srcu, idx);
-	} while (unlikely(encl->mm_list_version != mm_list_version));
+	sgx_zap_enclave_ptes(encl, addr);
 
 	mutex_lock(&encl->lock);
 
@@ -171,6 +149,8 @@
 			  backing->pcmd_offset;
 
 	ret = __ewb(&pginfo, sgx_get_epc_virt_addr(epc_page), va_slot);
+	set_page_dirty(backing->pcmd);
+	set_page_dirty(backing->contents);
 
 	kunmap_atomic((void *)(unsigned long)(pginfo.metadata -
 					      backing->pcmd_offset));
@@ -288,9 +268,10 @@
 	sgx_encl_ewb(epc_page, backing);
 	encl_page->epc_page = NULL;
 	encl->secs_child_cnt--;
+	sgx_encl_put_backing(backing);
 
 	if (!encl->secs_child_cnt && test_bit(SGX_ENCL_INITIALIZED, &encl->flags)) {
-		ret = sgx_encl_get_backing(encl, PFN_DOWN(encl->size),
+		ret = sgx_encl_alloc_backing(encl, PFN_DOWN(encl->size),
 					   &secs_backing);
 		if (ret)
 			goto out;
@@ -300,7 +281,7 @@
 		sgx_encl_free_epc_page(encl->secs.epc_page);
 		encl->secs.epc_page = NULL;
 
-		sgx_encl_put_backing(&secs_backing, true);
+		sgx_encl_put_backing(&secs_backing);
 	}
 
 out:
@@ -361,11 +342,14 @@
 			goto skip;
 
 		page_index = PFN_DOWN(encl_page->desc - encl_page->encl->base);
-		ret = sgx_encl_get_backing(encl_page->encl, page_index, &backing[i]);
-		if (ret)
-			goto skip;
 
 		mutex_lock(&encl_page->encl->lock);
+		ret = sgx_encl_alloc_backing(encl_page->encl, page_index, &backing[i]);
+		if (ret) {
+			mutex_unlock(&encl_page->encl->lock);
+			goto skip;
+		}
+
 		encl_page->desc |= SGX_ENCL_PAGE_BEING_RECLAIMED;
 		mutex_unlock(&encl_page->encl->lock);
 		continue;
@@ -393,7 +377,6 @@
 
 		encl_page = epc_page->owner;
 		sgx_reclaimer_write(epc_page, &backing[i]);
-		sgx_encl_put_backing(&backing[i], true);
 
 		kref_put(&encl_page->encl->refcount, sgx_encl_release);
 		epc_page->flags &= ~SGX_EPC_PAGE_RECLAIMER_TRACKED;
@@ -403,14 +386,15 @@
 
 		spin_lock(&node->lock);
 		list_add_tail(&epc_page->list, &node->free_page_list);
-		sgx_nr_free_pages++;
 		spin_unlock(&node->lock);
+		atomic_long_inc(&sgx_nr_free_pages);
 	}
 }
 
 static bool sgx_should_reclaim(unsigned long watermark)
 {
-	return sgx_nr_free_pages < watermark && !list_empty(&sgx_active_page_list);
+	return atomic_long_read(&sgx_nr_free_pages) < watermark &&
+	       !list_empty(&sgx_active_page_list);
 }
 
 static int ksgxd(void *p)
@@ -422,10 +406,7 @@
 	 * required for SECS pages, whose child pages blocked EREMOVE.
 	 */
 	__sgx_sanitize_pages(&sgx_dirty_page_list);
-	__sgx_sanitize_pages(&sgx_dirty_page_list);
-
-	/* sanity check: */
-	WARN_ON(!list_empty(&sgx_dirty_page_list));
+	WARN_ON(__sgx_sanitize_pages(&sgx_dirty_page_list));
 
 	while (!kthread_should_stop()) {
 		if (try_to_freeze())
@@ -457,6 +438,11 @@
 	return true;
 }
 
+bool current_is_ksgxd(void)
+{
+	return current == ksgxd_tsk;
+}
+
 static struct sgx_epc_page *__sgx_alloc_epc_page_from_node(int nid)
 {
 	struct sgx_numa_node *node = &sgx_numa_nodes[nid];
@@ -471,9 +457,9 @@
 
 	page = list_first_entry(&node->free_page_list, struct sgx_epc_page, list);
 	list_del_init(&page->list);
-	sgx_nr_free_pages--;
 
 	spin_unlock(&node->lock);
+	atomic_long_dec(&sgx_nr_free_pages);
 
 	return page;
 }
@@ -492,24 +478,25 @@
 {
 	struct sgx_epc_page *page;
 	int nid_of_current = numa_node_id();
-	int nid = nid_of_current;
-
-	if (node_isset(nid_of_current, sgx_numa_mask)) {
-		page = __sgx_alloc_epc_page_from_node(nid_of_current);
-		if (page)
-			return page;
-	}
+	int nid_start, nid;
 
-	/* Fall back to the non-local NUMA nodes: */
-	while (true) {
-		nid = next_node_in(nid, sgx_numa_mask);
-		if (nid == nid_of_current)
-			break;
+	/*
+	 * Try local node first. If it doesn't have an EPC section,
+	 * fall back to the non-local NUMA nodes.
+	 */
+	if (node_isset(nid_of_current, sgx_numa_mask))
+		nid_start = nid_of_current;
+	else
+		nid_start = next_node_in(nid_of_current, sgx_numa_mask);
 
+	nid = nid_start;
+	do {
 		page = __sgx_alloc_epc_page_from_node(nid);
 		if (page)
 			return page;
-	}
+
+		nid = next_node_in(nid, sgx_numa_mask);
+	} while (nid != nid_start);
 
 	return ERR_PTR(-ENOMEM);
 }
@@ -625,9 +612,9 @@
 	spin_lock(&node->lock);
 
 	list_add_tail(&page->list, &node->free_page_list);
-	sgx_nr_free_pages++;
 
 	spin_unlock(&node->lock);
+	atomic_long_inc(&sgx_nr_free_pages);
 }
 
 static bool __init sgx_setup_epc_section(u64 phys_addr, u64 size,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/sgx/virt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/sgx/virt.c
@@ -167,6 +167,7 @@
 			continue;
 
 		xa_erase(&vepc->page_array, index);
+		cond_resched();
 	}
 
 	/*
@@ -185,6 +186,7 @@
 			list_add_tail(&epc_page->list, &secs_pages);
 
 		xa_erase(&vepc->page_array, index);
+		cond_resched();
 	}
 
 	/*
@@ -206,6 +208,7 @@
 
 		if (sgx_vepc_free_page(epc_page))
 			list_add_tail(&epc_page->list, &secs_pages);
+		cond_resched();
 	}
 
 	if (!list_empty(&secs_pages))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/topology.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/topology.c
@@ -79,7 +79,7 @@
 	 * initial apic id, which also represents 32-bit extended x2apic id.
 	 */
 	c->initial_apicid = edx;
-	smp_num_siblings = LEVEL_MAX_SIBLINGS(ebx);
+	smp_num_siblings = max_t(int, smp_num_siblings, LEVEL_MAX_SIBLINGS(ebx));
 #endif
 	return 0;
 }
@@ -96,6 +96,7 @@
 	unsigned int ht_mask_width, core_plus_mask_width, die_plus_mask_width;
 	unsigned int core_select_mask, core_level_siblings;
 	unsigned int die_select_mask, die_level_siblings;
+	unsigned int pkg_mask_width;
 	bool die_level_present = false;
 	int leaf;
 
@@ -108,13 +109,14 @@
 	 */
 	cpuid_count(leaf, SMT_LEVEL, &eax, &ebx, &ecx, &edx);
 	c->initial_apicid = edx;
-	core_level_siblings = smp_num_siblings = LEVEL_MAX_SIBLINGS(ebx);
+	core_level_siblings = LEVEL_MAX_SIBLINGS(ebx);
+	smp_num_siblings = max_t(int, smp_num_siblings, LEVEL_MAX_SIBLINGS(ebx));
 	core_plus_mask_width = ht_mask_width = BITS_SHIFT_NEXT_LEVEL(eax);
 	die_level_siblings = LEVEL_MAX_SIBLINGS(ebx);
-	die_plus_mask_width = BITS_SHIFT_NEXT_LEVEL(eax);
+	pkg_mask_width = die_plus_mask_width = BITS_SHIFT_NEXT_LEVEL(eax);
 
 	sub_index = 1;
-	do {
+	while (true) {
 		cpuid_count(leaf, sub_index, &eax, &ebx, &ecx, &edx);
 
 		/*
@@ -132,10 +134,15 @@
 			die_plus_mask_width = BITS_SHIFT_NEXT_LEVEL(eax);
 		}
 
+		if (LEAFB_SUBTYPE(ecx) != INVALID_TYPE)
+			pkg_mask_width = BITS_SHIFT_NEXT_LEVEL(eax);
+		else
+			break;
+
 		sub_index++;
-	} while (LEAFB_SUBTYPE(ecx) != INVALID_TYPE);
+	}
 
-	core_select_mask = (~(-1 << core_plus_mask_width)) >> ht_mask_width;
+	core_select_mask = (~(-1 << pkg_mask_width)) >> ht_mask_width;
 	die_select_mask = (~(-1 << die_plus_mask_width)) >>
 				core_plus_mask_width;
 
@@ -148,7 +155,7 @@
 	}
 
 	c->phys_proc_id = apic->phys_pkg_id(c->initial_apicid,
-				die_plus_mask_width);
+				pkg_mask_width);
 	/*
 	 * Reinit the apicid, now that we have extended initial_apicid.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/cpu/tsx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/cpu/tsx.c
@@ -19,7 +19,7 @@
 
 enum tsx_ctrl_states tsx_ctrl_state __ro_after_init = TSX_CTRL_NOT_SUPPORTED;
 
-void tsx_disable(void)
+static void tsx_disable(void)
 {
 	u64 tsx;
 
@@ -39,7 +39,7 @@
 	wrmsrl(MSR_IA32_TSX_CTRL, tsx);
 }
 
-void tsx_enable(void)
+static void tsx_enable(void)
 {
 	u64 tsx;
 
@@ -58,24 +58,6 @@
 	wrmsrl(MSR_IA32_TSX_CTRL, tsx);
 }
 
-static bool __init tsx_ctrl_is_supported(void)
-{
-	u64 ia32_cap = x86_read_arch_cap_msr();
-
-	/*
-	 * TSX is controlled via MSR_IA32_TSX_CTRL.  However, support for this
-	 * MSR is enumerated by ARCH_CAP_TSX_MSR bit in MSR_IA32_ARCH_CAPABILITIES.
-	 *
-	 * TSX control (aka MSR_IA32_TSX_CTRL) is only available after a
-	 * microcode update on CPUs that have their MSR_IA32_ARCH_CAPABILITIES
-	 * bit MDS_NO=1. CPUs with MDS_NO=0 are not planned to get
-	 * MSR_IA32_TSX_CTRL support even after a microcode update. Thus,
-	 * tsx= cmdline requests will do nothing on CPUs without
-	 * MSR_IA32_TSX_CTRL support.
-	 */
-	return !!(ia32_cap & ARCH_CAP_TSX_CTRL_MSR);
-}
-
 static enum tsx_ctrl_states x86_get_tsx_auto_mode(void)
 {
 	if (boot_cpu_has_bug(X86_BUG_TAA))
@@ -84,7 +66,45 @@
 	return TSX_CTRL_ENABLE;
 }
 
-void tsx_clear_cpuid(void)
+/*
+ * Disabling TSX is not a trivial business.
+ *
+ * First of all, there's a CPUID bit: X86_FEATURE_RTM_ALWAYS_ABORT
+ * which says that TSX is practically disabled (all transactions are
+ * aborted by default). When that bit is set, the kernel unconditionally
+ * disables TSX.
+ *
+ * In order to do that, however, it needs to dance a bit:
+ *
+ * 1. The first method to disable it is through MSR_TSX_FORCE_ABORT and
+ * the MSR is present only when *two* CPUID bits are set:
+ *
+ * - X86_FEATURE_RTM_ALWAYS_ABORT
+ * - X86_FEATURE_TSX_FORCE_ABORT
+ *
+ * 2. The second method is for CPUs which do not have the above-mentioned
+ * MSR: those use a different MSR - MSR_IA32_TSX_CTRL and disable TSX
+ * through that one. Those CPUs can also have the initially mentioned
+ * CPUID bit X86_FEATURE_RTM_ALWAYS_ABORT set and for those the same strategy
+ * applies: TSX gets disabled unconditionally.
+ *
+ * When either of the two methods are present, the kernel disables TSX and
+ * clears the respective RTM and HLE feature flags.
+ *
+ * An additional twist in the whole thing presents late microcode loading
+ * which, when done, may cause for the X86_FEATURE_RTM_ALWAYS_ABORT CPUID
+ * bit to be set after the update.
+ *
+ * A subsequent hotplug operation on any logical CPU except the BSP will
+ * cause for the supported CPUID feature bits to get re-detected and, if
+ * RTM and HLE get cleared all of a sudden, but, userspace did consult
+ * them before the update, then funny explosions will happen. Long story
+ * short: the kernel doesn't modify CPUID feature bits after booting.
+ *
+ * That's why, this function's call in init_intel() doesn't clear the
+ * feature flags.
+ */
+static void tsx_clear_cpuid(void)
 {
 	u64 msr;
 
@@ -97,6 +117,40 @@
 		rdmsrl(MSR_TSX_FORCE_ABORT, msr);
 		msr |= MSR_TFA_TSX_CPUID_CLEAR;
 		wrmsrl(MSR_TSX_FORCE_ABORT, msr);
+	} else if (cpu_feature_enabled(X86_FEATURE_MSR_TSX_CTRL)) {
+		rdmsrl(MSR_IA32_TSX_CTRL, msr);
+		msr |= TSX_CTRL_CPUID_CLEAR;
+		wrmsrl(MSR_IA32_TSX_CTRL, msr);
+	}
+}
+
+/*
+ * Disable TSX development mode
+ *
+ * When the microcode released in Feb 2022 is applied, TSX will be disabled by
+ * default on some processors. MSR 0x122 (TSX_CTRL) and MSR 0x123
+ * (IA32_MCU_OPT_CTRL) can be used to re-enable TSX for development, doing so is
+ * not recommended for production deployments. In particular, applying MD_CLEAR
+ * flows for mitigation of the Intel TSX Asynchronous Abort (TAA) transient
+ * execution attack may not be effective on these processors when Intel TSX is
+ * enabled with updated microcode.
+ */
+static void tsx_dev_mode_disable(void)
+{
+	u64 mcu_opt_ctrl;
+
+	/* Check if RTM_ALLOW exists */
+	if (!boot_cpu_has_bug(X86_BUG_TAA) ||
+	    !cpu_feature_enabled(X86_FEATURE_MSR_TSX_CTRL) ||
+	    !cpu_feature_enabled(X86_FEATURE_SRBDS_CTRL))
+		return;
+
+	rdmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_opt_ctrl);
+
+	if (mcu_opt_ctrl & RTM_ALLOW) {
+		mcu_opt_ctrl &= ~RTM_ALLOW;
+		wrmsrl(MSR_IA32_MCU_OPT_CTRL, mcu_opt_ctrl);
+		setup_force_cpu_cap(X86_FEATURE_RTM_ALWAYS_ABORT);
 	}
 }
 
@@ -105,14 +159,14 @@
 	char arg[5] = {};
 	int ret;
 
+	tsx_dev_mode_disable();
+
 	/*
-	 * Hardware will always abort a TSX transaction if both CPUID bits
-	 * RTM_ALWAYS_ABORT and TSX_FORCE_ABORT are set. In this case, it is
-	 * better not to enumerate CPUID.RTM and CPUID.HLE bits. Clear them
-	 * here.
+	 * Hardware will always abort a TSX transaction when the CPUID bit
+	 * RTM_ALWAYS_ABORT is set. In this case, it is better not to enumerate
+	 * CPUID.RTM and CPUID.HLE bits. Clear them here.
 	 */
-	if (boot_cpu_has(X86_FEATURE_RTM_ALWAYS_ABORT) &&
-	    boot_cpu_has(X86_FEATURE_TSX_FORCE_ABORT)) {
+	if (boot_cpu_has(X86_FEATURE_RTM_ALWAYS_ABORT)) {
 		tsx_ctrl_state = TSX_CTRL_RTM_ALWAYS_ABORT;
 		tsx_clear_cpuid();
 		setup_clear_cpu_cap(X86_FEATURE_RTM);
@@ -120,7 +174,20 @@
 		return;
 	}
 
-	if (!tsx_ctrl_is_supported()) {
+	/*
+	 * TSX is controlled via MSR_IA32_TSX_CTRL.  However, support for this
+	 * MSR is enumerated by ARCH_CAP_TSX_MSR bit in MSR_IA32_ARCH_CAPABILITIES.
+	 *
+	 * TSX control (aka MSR_IA32_TSX_CTRL) is only available after a
+	 * microcode update on CPUs that have their MSR_IA32_ARCH_CAPABILITIES
+	 * bit MDS_NO=1. CPUs with MDS_NO=0 are not planned to get
+	 * MSR_IA32_TSX_CTRL support even after a microcode update. Thus,
+	 * tsx= cmdline requests will do nothing on CPUs without
+	 * MSR_IA32_TSX_CTRL support.
+	 */
+	if (x86_read_arch_cap_msr() & ARCH_CAP_TSX_CTRL_MSR) {
+		setup_force_cpu_cap(X86_FEATURE_MSR_TSX_CTRL);
+	} else {
 		tsx_ctrl_state = TSX_CTRL_NOT_SUPPORTED;
 		return;
 	}
@@ -175,3 +242,16 @@
 		setup_force_cpu_cap(X86_FEATURE_HLE);
 	}
 }
+
+void tsx_ap_init(void)
+{
+	tsx_dev_mode_disable();
+
+	if (tsx_ctrl_state == TSX_CTRL_ENABLE)
+		tsx_enable();
+	else if (tsx_ctrl_state == TSX_CTRL_DISABLE)
+		tsx_disable();
+	else if (tsx_ctrl_state == TSX_CTRL_RTM_ALWAYS_ABORT)
+		/* See comment over that function for more details. */
+		tsx_clear_cpuid();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/crash.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/crash.c
@@ -37,7 +37,6 @@
 #include <linux/kdebug.h>
 #include <asm/cpu.h>
 #include <asm/reboot.h>
-#include <asm/virtext.h>
 #include <asm/intel_pt.h>
 #include <asm/crash.h>
 #include <asm/cmdline.h>
@@ -81,15 +80,6 @@
 	 */
 	cpu_crash_vmclear_loaded_vmcss();
 
-	/* Disable VMX or SVM if needed.
-	 *
-	 * We need to disable virtualization on all CPUs.
-	 * Having VMX or SVM enabled on any CPU may break rebooting
-	 * after the kdump kernel has finished its task.
-	 */
-	cpu_emergency_vmxoff();
-	cpu_emergency_svm_disable();
-
 	/*
 	 * Disable Intel PT to stop its logging
 	 */
@@ -148,12 +138,7 @@
 	 */
 	cpu_crash_vmclear_loaded_vmcss();
 
-	/* Booting kdump kernel with VMX or SVM enabled won't work,
-	 * because (among other limitations) we can't disable paging
-	 * with the virt flags.
-	 */
-	cpu_emergency_vmxoff();
-	cpu_emergency_svm_disable();
+	cpu_emergency_disable_virtualization();
 
 	/*
 	 * Disable Intel PT to stop its logging
@@ -401,10 +386,8 @@
 	kbuf.buf_align = ELF_CORE_HEADER_ALIGN;
 	kbuf.mem = KEXEC_BUF_MEM_UNKNOWN;
 	ret = kexec_add_buffer(&kbuf);
-	if (ret) {
-		vfree((void *)image->elf_headers);
+	if (ret)
 		return ret;
-	}
 	image->elf_load_addr = kbuf.mem;
 	pr_debug("Loaded ELF headers at 0x%lx bufsz=0x%lx memsz=0x%lx\n",
 		 image->elf_load_addr, kbuf.bufsz, kbuf.bufsz);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/devicetree.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/devicetree.c
@@ -92,7 +92,7 @@
 
 	ret = pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
 	if (ret)
-		return ret;
+		return pcibios_err_to_errno(ret);
 	if (!pin)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/dumpstack.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/dumpstack.c
@@ -195,7 +195,7 @@
 	printk("%sCall Trace:\n", log_lvl);
 
 	unwind_start(&state, task, regs, stack);
-	stack = stack ? : get_stack_pointer(task, regs);
+	stack = stack ?: get_stack_pointer(task, regs);
 	regs = unwind_get_entry_regs(&state, &partial);
 
 	/*
@@ -214,9 +214,11 @@
 	 * - hardirq stack
 	 * - entry stack
 	 */
-	for ( ; stack; stack = PTR_ALIGN(stack_info.next_sp, sizeof(long))) {
+	for (; stack; stack = stack_info.next_sp) {
 		const char *stack_name;
 
+		stack = PTR_ALIGN(stack, sizeof(long));
+
 		if (get_stack_info(stack, task, &stack_info, &visit_mask)) {
 			/*
 			 * We weren't on a valid stack.  It's possible that
@@ -351,7 +353,7 @@
 }
 NOKPROBE_SYMBOL(oops_begin);
 
-void __noreturn rewind_stack_do_exit(int signr);
+void __noreturn rewind_stack_and_make_dead(int signr);
 
 void oops_end(unsigned long flags, struct pt_regs *regs, int signr)
 {
@@ -386,7 +388,7 @@
 	 * reuse the task stack and that existing poisons are invalid.
 	 */
 	kasan_unpoison_task_stack(current);
-	rewind_stack_do_exit(signr);
+	rewind_stack_and_make_dead(signr);
 }
 NOKPROBE_SYMBOL(oops_end);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/dumpstack_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/dumpstack_64.c
@@ -32,9 +32,15 @@
 {
 	BUILD_BUG_ON(N_EXCEPTION_STACKS != 6);
 
+	if (type == STACK_TYPE_TASK)
+		return "TASK";
+
 	if (type == STACK_TYPE_IRQ)
 		return "IRQ";
 
+	if (type == STACK_TYPE_SOFTIRQ)
+		return "SOFTIRQ";
+
 	if (type == STACK_TYPE_ENTRY) {
 		/*
 		 * On 64-bit, we have a generic entry stack that we
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/e820.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/e820.c
@@ -995,8 +995,10 @@
  */
 void __init e820__reserve_setup_data(void)
 {
+	struct setup_indirect *indirect;
 	struct setup_data *data;
-	u64 pa_data;
+	u64 pa_data, pa_next;
+	u32 len;
 
 	pa_data = boot_params.hdr.setup_data;
 	if (!pa_data)
@@ -1004,6 +1006,14 @@
 
 	while (pa_data) {
 		data = early_memremap(pa_data, sizeof(*data));
+		if (!data) {
+			pr_warn("e820: failed to memremap setup_data entry\n");
+			return;
+		}
+
+		len = sizeof(*data);
+		pa_next = data->next;
+
 		e820__range_update(pa_data, sizeof(*data)+data->len, E820_TYPE_RAM, E820_TYPE_RESERVED_KERN);
 
 		/*
@@ -1015,18 +1025,27 @@
 						 sizeof(*data) + data->len,
 						 E820_TYPE_RAM, E820_TYPE_RESERVED_KERN);
 
-		if (data->type == SETUP_INDIRECT &&
-		    ((struct setup_indirect *)data->data)->type != SETUP_INDIRECT) {
-			e820__range_update(((struct setup_indirect *)data->data)->addr,
-					   ((struct setup_indirect *)data->data)->len,
-					   E820_TYPE_RAM, E820_TYPE_RESERVED_KERN);
-			e820__range_update_kexec(((struct setup_indirect *)data->data)->addr,
-						 ((struct setup_indirect *)data->data)->len,
-						 E820_TYPE_RAM, E820_TYPE_RESERVED_KERN);
+		if (data->type == SETUP_INDIRECT) {
+			len += data->len;
+			early_memunmap(data, sizeof(*data));
+			data = early_memremap(pa_data, len);
+			if (!data) {
+				pr_warn("e820: failed to memremap indirect setup_data\n");
+				return;
+			}
+
+			indirect = (struct setup_indirect *)data->data;
+
+			if (indirect->type != SETUP_INDIRECT) {
+				e820__range_update(indirect->addr, indirect->len,
+						   E820_TYPE_RAM, E820_TYPE_RESERVED_KERN);
+				e820__range_update_kexec(indirect->addr, indirect->len,
+							 E820_TYPE_RAM, E820_TYPE_RESERVED_KERN);
+			}
 		}
 
-		pa_data = data->next;
-		early_memunmap(data, sizeof(*data));
+		pa_data = pa_next;
+		early_memunmap(data, len);
 	}
 
 	e820__update_table(e820_table);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/early-quirks.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/early-quirks.c
@@ -28,6 +28,37 @@
 #include <asm/irq_remapping.h>
 #include <asm/early_ioremap.h>
 
+static void __init early_pci_clear_msi(int bus, int slot, int func)
+{
+	int pos;
+	u16 ctrl;
+
+	if (likely(!pci_early_clear_msi))
+		return;
+
+	pr_info_once("Clearing MSI/MSI-X enable bits early in boot (quirk)\n");
+
+	pos = pci_early_find_cap(bus, slot, func, PCI_CAP_ID_MSI);
+	if (pos) {
+		ctrl = read_pci_config_16(bus, slot, func, pos + PCI_MSI_FLAGS);
+		ctrl &= ~PCI_MSI_FLAGS_ENABLE;
+		write_pci_config_16(bus, slot, func, pos + PCI_MSI_FLAGS, ctrl);
+
+		/* Read again to flush previous write */
+		ctrl = read_pci_config_16(bus, slot, func, pos + PCI_MSI_FLAGS);
+	}
+
+	pos = pci_early_find_cap(bus, slot, func, PCI_CAP_ID_MSIX);
+	if (pos) {
+		ctrl = read_pci_config_16(bus, slot, func, pos + PCI_MSIX_FLAGS);
+		ctrl &= ~PCI_MSIX_FLAGS_ENABLE;
+		write_pci_config_16(bus, slot, func, pos + PCI_MSIX_FLAGS, ctrl);
+
+		/* Read again to flush previous write */
+		ctrl = read_pci_config_16(bus, slot, func, pos + PCI_MSIX_FLAGS);
+	}
+}
+
 static void __init fix_hypertransport_config(int num, int slot, int func)
 {
 	u32 htcfg;
@@ -515,6 +546,7 @@
 	.stolen_size = gen9_stolen_size,
 };
 
+/* Intel integrated GPUs for which we need to reserve "stolen memory" */
 static const struct pci_device_id intel_early_ids[] __initconst = {
 	INTEL_I830_IDS(&i830_early_ops),
 	INTEL_I845G_IDS(&i845_early_ops),
@@ -591,6 +623,13 @@
 	u16 device;
 	int i;
 
+	/*
+	 * Reserve "stolen memory" for an integrated GPU.  If we've already
+	 * found one, there's nothing to do for other (discrete) GPUs.
+	 */
+	if (resource_size(&intel_graphics_stolen_res))
+		return;
+
 	device = read_pci_config_16(num, slot, func, PCI_DEVICE_ID);
 
 	for (i = 0; i < ARRAY_SIZE(intel_early_ids); i++) {
@@ -703,7 +742,7 @@
 	{ PCI_VENDOR_ID_INTEL, 0x3406, PCI_CLASS_BRIDGE_HOST,
 	  PCI_BASE_CLASS_BRIDGE, 0, intel_remapping_check },
 	{ PCI_VENDOR_ID_INTEL, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA, PCI_ANY_ID,
-	  QFLAG_APPLY_ONCE, intel_graphics_quirks },
+	  0, intel_graphics_quirks },
 	/*
 	 * HPET on the current version of the Baytrail platform has accuracy
 	 * problems: it will halt in deep idle state - so we disable it.
@@ -716,6 +755,7 @@
 		PCI_CLASS_BRIDGE_HOST, PCI_ANY_ID, 0, force_disable_hpet},
 	{ PCI_VENDOR_ID_BROADCOM, 0x4331,
 	  PCI_CLASS_NETWORK_OTHER, PCI_ANY_ID, 0, apple_airport_reset},
+	{ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, early_pci_clear_msi},
 	{}
 };
 
@@ -768,6 +808,10 @@
 				    PCI_HEADER_TYPE);
 
 	if ((type & 0x7f) == PCI_HEADER_TYPE_BRIDGE) {
+		/* pci_early_clear_msi scans the buses differently. */
+		if (pci_early_clear_msi)
+			return -1;
+
 		sec = read_pci_config_byte(num, slot, func, PCI_SECONDARY_BUS);
 		if (sec > num)
 			early_pci_scan_bus(sec);
@@ -794,8 +838,13 @@
 
 void __init early_quirks(void)
 {
+	int bus;
+
 	if (!early_pci_allowed())
 		return;
 
 	early_pci_scan_bus(0);
+	/* pci_early_clear_msi scans more buses. */
+	for (bus = 1; pci_early_clear_msi && bus < 256; bus++)
+		early_pci_scan_bus(bus);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/bugs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/bugs.c
@@ -2,7 +2,7 @@
 /*
  * x86 FPU bug checks:
  */
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 
 /*
  * Boot time CPU/FPU FDIV bug detection code:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/context.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/context.h
@@ -0,0 +1,83 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __X86_KERNEL_FPU_CONTEXT_H
+#define __X86_KERNEL_FPU_CONTEXT_H
+
+#include <asm/fpu/xstate.h>
+#include <asm/trace/fpu.h>
+
+/* Functions related to FPU context tracking */
+
+/*
+ * The in-register FPU state for an FPU context on a CPU is assumed to be
+ * valid if the fpu->last_cpu matches the CPU, and the fpu_fpregs_owner_ctx
+ * matches the FPU.
+ *
+ * If the FPU register state is valid, the kernel can skip restoring the
+ * FPU state from memory.
+ *
+ * Any code that clobbers the FPU registers or updates the in-memory
+ * FPU state for a task MUST let the rest of the kernel know that the
+ * FPU registers are no longer valid for this task.
+ *
+ * Either one of these invalidation functions is enough. Invalidate
+ * a resource you control: CPU if using the CPU for something else
+ * (with preemption disabled), FPU for the current task, or a task that
+ * is prevented from running by the current task.
+ */
+static inline void __cpu_invalidate_fpregs_state(void)
+{
+	__this_cpu_write(fpu_fpregs_owner_ctx, NULL);
+}
+
+static inline void __fpu_invalidate_fpregs_state(struct fpu *fpu)
+{
+	fpu->last_cpu = -1;
+}
+
+static inline int fpregs_state_valid(struct fpu *fpu, unsigned int cpu)
+{
+	return fpu == this_cpu_read(fpu_fpregs_owner_ctx) && cpu == fpu->last_cpu;
+}
+
+static inline void fpregs_deactivate(struct fpu *fpu)
+{
+	__this_cpu_write(fpu_fpregs_owner_ctx, NULL);
+	trace_x86_fpu_regs_deactivated(fpu);
+}
+
+static inline void fpregs_activate(struct fpu *fpu)
+{
+	__this_cpu_write(fpu_fpregs_owner_ctx, fpu);
+	trace_x86_fpu_regs_activated(fpu);
+}
+
+/* Internal helper for switch_fpu_return() and signal frame setup */
+static inline void fpregs_restore_userregs(void)
+{
+	struct fpu *fpu = &current->thread.fpu;
+	int cpu = smp_processor_id();
+
+	if (WARN_ON_ONCE(current->flags & PF_KTHREAD))
+		return;
+
+	if (!fpregs_state_valid(fpu, cpu)) {
+		/*
+		 * This restores _all_ xstate which has not been
+		 * established yet.
+		 *
+		 * If PKRU is enabled, then the PKRU value is already
+		 * correct because it was either set in switch_to() or in
+		 * flush_thread(). So it is excluded because it might be
+		 * not up to date in current->thread.fpu.xsave state.
+		 *
+		 * XFD state is handled in restore_fpregs_from_fpstate().
+		 */
+		restore_fpregs_from_fpstate(fpu->fpstate, XFEATURE_MASK_FPSTATE);
+
+		fpregs_activate(fpu);
+		fpu->last_cpu = cpu;
+	}
+	clear_thread_flag(TIF_NEED_FPU_LOAD);
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/core.c
@@ -6,8 +6,9 @@
  *  General FPU state handling cleanups
  *	Gareth Hughes <gareth@valinux.com>, May 2000
  */
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/fpu/regset.h>
+#include <asm/fpu/sched.h>
 #include <asm/fpu/signal.h>
 #include <asm/fpu/types.h>
 #include <asm/traps.h>
@@ -16,26 +17,30 @@
 #include <linux/hardirq.h>
 #include <linux/pkeys.h>
 
+#include "context.h"
+#include "internal.h"
+#include "legacy.h"
+#include "xstate.h"
+
 #define CREATE_TRACE_POINTS
 #include <asm/trace/fpu.h>
 
+#ifdef CONFIG_X86_64
+DEFINE_STATIC_KEY_FALSE(__fpu_state_size_dynamic);
+DEFINE_PER_CPU(u64, xfd_state);
+#endif
+
+/* The FPU state configuration data for kernel and user space */
+struct fpu_state_config	fpu_kernel_cfg __ro_after_init;
+struct fpu_state_config fpu_user_cfg __ro_after_init;
+
 /*
  * Represents the initial FPU state. It's mostly (but not completely) zeroes,
  * depending on the FPU hardware format:
  */
-union fpregs_state init_fpstate __ro_after_init;
+struct fpstate init_fpstate __ro_after_init;
 
-/*
- * Track whether the kernel is using the FPU state
- * currently.
- *
- * This flag is used:
- *
- *   - by IRQ context code to potentially use the FPU
- *     if it's unused.
- *
- *   - to debug kernel_fpu_begin()/end() correctness
- */
+/* Track in-kernel FPU usage */
 static DEFINE_PER_CPU(bool, in_kernel_fpu);
 
 /*
@@ -43,47 +48,42 @@
  */
 DEFINE_PER_CPU(struct fpu *, fpu_fpregs_owner_ctx);
 
-static bool kernel_fpu_disabled(void)
-{
-	return this_cpu_read(in_kernel_fpu);
-}
-
-static bool interrupted_kernel_fpu_idle(void)
-{
-	return !kernel_fpu_disabled();
-}
-
-/*
- * Were we in user mode (or vm86 mode) when we were
- * interrupted?
- *
- * Doing kernel_fpu_begin/end() is ok if we are running
- * in an interrupt context from user mode - we'll just
- * save the FPU state as required.
- */
-static bool interrupted_user_mode(void)
-{
-	struct pt_regs *regs = get_irq_regs();
-	return regs && user_mode(regs);
-}
-
 /*
  * Can we use the FPU in kernel mode with the
  * whole "kernel_fpu_begin/end()" sequence?
- *
- * It's always ok in process context (ie "not interrupt")
- * but it is sometimes ok even from an irq.
  */
 bool irq_fpu_usable(void)
 {
-	return !in_interrupt() ||
-		interrupted_user_mode() ||
-		interrupted_kernel_fpu_idle();
+	if (WARN_ON_ONCE(in_nmi()))
+		return false;
+
+	/* In kernel FPU usage already active? */
+	if (this_cpu_read(in_kernel_fpu))
+		return false;
+
+	/*
+	 * When not in NMI or hard interrupt context, FPU can be used in:
+	 *
+	 * - Task context except from within fpregs_lock()'ed critical
+	 *   regions.
+	 *
+	 * - Soft interrupt processing context which cannot happen
+	 *   while in a fpregs_lock()'ed critical region.
+	 */
+	if (!in_hardirq())
+		return true;
+
+	/*
+	 * In hard interrupt context it's safe when soft interrupts
+	 * are enabled, which means the interrupt did not hit in
+	 * a fpregs_lock()'ed critical region.
+	 */
+	return !softirq_count();
 }
 EXPORT_SYMBOL(irq_fpu_usable);
 
 /*
- * Save the FPU register state in fpu->state. The register state is
+ * Save the FPU register state in fpu->fpstate->regs. The register state is
  * preserved.
  *
  * Must be called with fpregs_lock() held.
@@ -99,19 +99,19 @@
 void save_fpregs_to_fpstate(struct fpu *fpu)
 {
 	if (likely(use_xsave())) {
-		os_xsave(&fpu->state.xsave);
+		os_xsave(fpu->fpstate);
 
 		/*
 		 * AVX512 state is tracked here because its use is
 		 * known to slow the max clock speed of the core.
 		 */
-		if (fpu->state.xsave.header.xfeatures & XFEATURE_MASK_AVX512)
+		if (fpu->fpstate->regs.xsave.header.xfeatures & XFEATURE_MASK_AVX512)
 			fpu->avx512_timestamp = jiffies;
 		return;
 	}
 
 	if (likely(use_fxsr())) {
-		fxsave(&fpu->state.fxsave);
+		fxsave(&fpu->fpstate->regs.fxsave);
 		return;
 	}
 
@@ -119,12 +119,11 @@
 	 * Legacy FPU register saving, FNSAVE always clears FPU registers,
 	 * so we have to reload them from the memory state.
 	 */
-	asm volatile("fnsave %[fp]; fwait" : [fp] "=m" (fpu->state.fsave));
-	frstor(&fpu->state.fsave);
+	asm volatile("fnsave %[fp]; fwait" : [fp] "=m" (fpu->fpstate->regs.fsave));
+	frstor(&fpu->fpstate->regs.fsave);
 }
-EXPORT_SYMBOL(save_fpregs_to_fpstate);
 
-void __restore_fpregs_from_fpstate(union fpregs_state *fpstate, u64 mask)
+void restore_fpregs_from_fpstate(struct fpstate *fpstate, u64 mask)
 {
 	/*
 	 * AMD K7/K8 and later CPUs up to Zen don't save/restore
@@ -136,20 +135,187 @@
 		asm volatile(
 			"fnclex\n\t"
 			"emms\n\t"
-			"fildl %P[addr]"	/* set F?P to defined value */
-			: : [addr] "m" (fpstate));
+			"fildl %[addr]"	/* set F?P to defined value */
+			: : [addr] "m" (*fpstate));
 	}
 
 	if (use_xsave()) {
-		os_xrstor(&fpstate->xsave, mask);
+		/*
+		 * Dynamically enabled features are enabled in XCR0, but
+		 * usage requires also that the corresponding bits in XFD
+		 * are cleared.  If the bits are set then using a related
+		 * instruction will raise #NM. This allows to do the
+		 * allocation of the larger FPU buffer lazy from #NM or if
+		 * the task has no permission to kill it which would happen
+		 * via #UD if the feature is disabled in XCR0.
+		 *
+		 * XFD state is following the same life time rules as
+		 * XSTATE and to restore state correctly XFD has to be
+		 * updated before XRSTORS otherwise the component would
+		 * stay in or go into init state even if the bits are set
+		 * in fpstate::regs::xsave::xfeatures.
+		 */
+		xfd_update_state(fpstate);
+
+		/*
+		 * Restoring state always needs to modify all features
+		 * which are in @mask even if the current task cannot use
+		 * extended features.
+		 *
+		 * So fpstate->xfeatures cannot be used here, because then
+		 * a feature for which the task has no permission but was
+		 * used by the previous task would not go into init state.
+		 */
+		mask = fpu_kernel_cfg.max_features & mask;
+
+		os_xrstor(fpstate, mask);
 	} else {
 		if (use_fxsr())
-			fxrstor(&fpstate->fxsave);
+			fxrstor(&fpstate->regs.fxsave);
 		else
-			frstor(&fpstate->fsave);
+			frstor(&fpstate->regs.fsave);
 	}
 }
-EXPORT_SYMBOL_GPL(__restore_fpregs_from_fpstate);
+
+void fpu_reset_from_exception_fixup(void)
+{
+	restore_fpregs_from_fpstate(&init_fpstate, XFEATURE_MASK_FPSTATE);
+}
+
+#if IS_ENABLED(CONFIG_KVM)
+static void __fpstate_reset(struct fpstate *fpstate);
+
+bool fpu_alloc_guest_fpstate(struct fpu_guest *gfpu)
+{
+	struct fpstate *fpstate;
+	unsigned int size;
+
+	size = fpu_user_cfg.default_size + ALIGN(offsetof(struct fpstate, regs), 64);
+	fpstate = vzalloc(size);
+	if (!fpstate)
+		return false;
+
+	__fpstate_reset(fpstate);
+	fpstate_init_user(fpstate);
+	fpstate->is_valloc	= true;
+	fpstate->is_guest	= true;
+
+	gfpu->fpstate = fpstate;
+	return true;
+}
+EXPORT_SYMBOL_GPL(fpu_alloc_guest_fpstate);
+
+void fpu_free_guest_fpstate(struct fpu_guest *gfpu)
+{
+	struct fpstate *fps = gfpu->fpstate;
+
+	if (!fps)
+		return;
+
+	if (WARN_ON_ONCE(!fps->is_valloc || !fps->is_guest || fps->in_use))
+		return;
+
+	gfpu->fpstate = NULL;
+	vfree(fps);
+}
+EXPORT_SYMBOL_GPL(fpu_free_guest_fpstate);
+
+int fpu_swap_kvm_fpstate(struct fpu_guest *guest_fpu, bool enter_guest)
+{
+	struct fpstate *guest_fps = guest_fpu->fpstate;
+	struct fpu *fpu = &current->thread.fpu;
+	struct fpstate *cur_fps = fpu->fpstate;
+
+	fpregs_lock();
+	if (!cur_fps->is_confidential && !test_thread_flag(TIF_NEED_FPU_LOAD))
+		save_fpregs_to_fpstate(fpu);
+
+	/* Swap fpstate */
+	if (enter_guest) {
+		fpu->__task_fpstate = cur_fps;
+		fpu->fpstate = guest_fps;
+		guest_fps->in_use = true;
+	} else {
+		guest_fps->in_use = false;
+		fpu->fpstate = fpu->__task_fpstate;
+		fpu->__task_fpstate = NULL;
+	}
+
+	cur_fps = fpu->fpstate;
+
+	if (!cur_fps->is_confidential) {
+		/* Includes XFD update */
+		restore_fpregs_from_fpstate(cur_fps, XFEATURE_MASK_FPSTATE);
+	} else {
+		/*
+		 * XSTATE is restored by firmware from encrypted
+		 * memory. Make sure XFD state is correct while
+		 * running with guest fpstate
+		 */
+		xfd_update_state(cur_fps);
+	}
+
+	fpregs_mark_activate();
+	fpregs_unlock();
+	return 0;
+}
+EXPORT_SYMBOL_GPL(fpu_swap_kvm_fpstate);
+
+void fpu_copy_guest_fpstate_to_uabi(struct fpu_guest *gfpu, void *buf,
+				    unsigned int size, u64 xfeatures, u32 pkru)
+{
+	struct fpstate *kstate = gfpu->fpstate;
+	union fpregs_state *ustate = buf;
+	struct membuf mb = { .p = buf, .left = size };
+
+	if (cpu_feature_enabled(X86_FEATURE_XSAVE)) {
+		__copy_xstate_to_uabi_buf(mb, kstate, xfeatures, pkru,
+					  XSTATE_COPY_XSAVE);
+	} else {
+		memcpy(&ustate->fxsave, &kstate->regs.fxsave,
+		       sizeof(ustate->fxsave));
+		/* Make it restorable on a XSAVE enabled host */
+		ustate->xsave.header.xfeatures = XFEATURE_MASK_FPSSE;
+	}
+}
+EXPORT_SYMBOL_GPL(fpu_copy_guest_fpstate_to_uabi);
+
+int fpu_copy_uabi_to_guest_fpstate(struct fpu_guest *gfpu, const void *buf,
+				   u64 xcr0, u32 *vpkru)
+{
+	struct fpstate *kstate = gfpu->fpstate;
+	const union fpregs_state *ustate = buf;
+	struct pkru_state *xpkru;
+	int ret;
+
+	if (!cpu_feature_enabled(X86_FEATURE_XSAVE)) {
+		if (ustate->xsave.header.xfeatures & ~XFEATURE_MASK_FPSSE)
+			return -EINVAL;
+		if (ustate->fxsave.mxcsr & ~mxcsr_feature_mask)
+			return -EINVAL;
+		memcpy(&kstate->regs.fxsave, &ustate->fxsave, sizeof(ustate->fxsave));
+		return 0;
+	}
+
+	if (ustate->xsave.header.xfeatures & ~xcr0)
+		return -EINVAL;
+
+	ret = copy_uabi_from_kernel_to_xstate(kstate, ustate);
+	if (ret)
+		return ret;
+
+	/* Retrieve PKRU if not in init state */
+	if (kstate->regs.xsave.header.xfeatures & XFEATURE_MASK_PKRU) {
+		xpkru = get_xsave_addr(&kstate->regs.xsave, XFEATURE_PKRU);
+		*vpkru = xpkru->pkru;
+	}
+
+	/* Ensure that XCOMP_BV is set up for XSAVES */
+	xstate_init_xcomp_bv(&kstate->regs.xsave, kstate->xfeatures);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(fpu_copy_uabi_to_guest_fpstate);
+#endif /* CONFIG_KVM */
 
 void kernel_fpu_begin_mask(unsigned int kfpu_mask)
 {
@@ -203,52 +369,88 @@
 	fpregs_unlock();
 }
 
-static inline void fpstate_init_xstate(struct xregs_state *xsave)
+static inline unsigned int init_fpstate_copy_size(void)
 {
-	/*
-	 * XRSTORS requires these bits set in xcomp_bv, or it will
-	 * trigger #GP:
-	 */
-	xsave->header.xcomp_bv = XCOMP_BV_COMPACTED_FORMAT | xfeatures_mask_all;
+	if (!use_xsave())
+		return fpu_kernel_cfg.default_size;
+
+	/* XSAVE(S) just needs the legacy and the xstate header part */
+	return sizeof(init_fpstate.regs.xsave);
 }
 
-static inline void fpstate_init_fxstate(struct fxregs_state *fx)
+static inline void fpstate_init_fxstate(struct fpstate *fpstate)
 {
-	fx->cwd = 0x37f;
-	fx->mxcsr = MXCSR_DEFAULT;
+	fpstate->regs.fxsave.cwd = 0x37f;
+	fpstate->regs.fxsave.mxcsr = MXCSR_DEFAULT;
 }
 
 /*
  * Legacy x87 fpstate state init:
  */
-static inline void fpstate_init_fstate(struct fregs_state *fp)
+static inline void fpstate_init_fstate(struct fpstate *fpstate)
 {
-	fp->cwd = 0xffff037fu;
-	fp->swd = 0xffff0000u;
-	fp->twd = 0xffffffffu;
-	fp->fos = 0xffff0000u;
+	fpstate->regs.fsave.cwd = 0xffff037fu;
+	fpstate->regs.fsave.swd = 0xffff0000u;
+	fpstate->regs.fsave.twd = 0xffffffffu;
+	fpstate->regs.fsave.fos = 0xffff0000u;
 }
 
-void fpstate_init(union fpregs_state *state)
+/*
+ * Used in two places:
+ * 1) Early boot to setup init_fpstate for non XSAVE systems
+ * 2) fpu_init_fpstate_user() which is invoked from KVM
+ */
+void fpstate_init_user(struct fpstate *fpstate)
 {
-	if (!static_cpu_has(X86_FEATURE_FPU)) {
-		fpstate_init_soft(&state->soft);
+	if (!cpu_feature_enabled(X86_FEATURE_FPU)) {
+		fpstate_init_soft(&fpstate->regs.soft);
 		return;
 	}
 
-	memset(state, 0, fpu_kernel_xstate_size);
+	xstate_init_xcomp_bv(&fpstate->regs.xsave, fpstate->xfeatures);
 
-	if (static_cpu_has(X86_FEATURE_XSAVES))
-		fpstate_init_xstate(&state->xsave);
-	if (static_cpu_has(X86_FEATURE_FXSR))
-		fpstate_init_fxstate(&state->fxsave);
+	if (cpu_feature_enabled(X86_FEATURE_FXSR))
+		fpstate_init_fxstate(fpstate);
 	else
-		fpstate_init_fstate(&state->fsave);
+		fpstate_init_fstate(fpstate);
+}
+
+static void __fpstate_reset(struct fpstate *fpstate)
+{
+	/* Initialize sizes and feature masks */
+	fpstate->size		= fpu_kernel_cfg.default_size;
+	fpstate->user_size	= fpu_user_cfg.default_size;
+	fpstate->xfeatures	= fpu_kernel_cfg.default_features;
+	fpstate->user_xfeatures	= fpu_user_cfg.default_features;
+	fpstate->xfd		= init_fpstate.xfd;
+}
+
+void fpstate_reset(struct fpu *fpu)
+{
+	/* Set the fpstate pointer to the default fpstate */
+	fpu->fpstate = &fpu->__fpstate;
+	__fpstate_reset(fpu->fpstate);
+
+	/* Initialize the permission related info in fpu */
+	fpu->perm.__state_perm		= fpu_kernel_cfg.default_features;
+	fpu->perm.__state_size		= fpu_kernel_cfg.default_size;
+	fpu->perm.__user_state_size	= fpu_user_cfg.default_size;
+}
+
+static inline void fpu_inherit_perms(struct fpu *dst_fpu)
+{
+	if (fpu_state_size_dynamic()) {
+		struct fpu *src_fpu = &current->group_leader->thread.fpu;
+
+		spin_lock_irq(&current->sighand->siglock);
+		/* Fork also inherits the permissions of the parent */
+		dst_fpu->perm = src_fpu->perm;
+		spin_unlock_irq(&current->sighand->siglock);
+	}
 }
-EXPORT_SYMBOL_GPL(fpstate_init);
 
 /* Clone current's FPU state on fork */
-int fpu_clone(struct task_struct *dst)
+int fpu_clone(struct task_struct *dst, unsigned long clone_flags)
 {
 	struct fpu *src_fpu = &current->thread.fpu;
 	struct fpu *dst_fpu = &dst->thread.fpu;
@@ -256,30 +458,51 @@
 	/* The new task's FPU state cannot be valid in the hardware. */
 	dst_fpu->last_cpu = -1;
 
+	fpstate_reset(dst_fpu);
+
 	if (!cpu_feature_enabled(X86_FEATURE_FPU))
 		return 0;
 
 	/*
-	 * Don't let 'init optimized' areas of the XSAVE area
-	 * leak into the child task:
+	 * Enforce reload for user space tasks and prevent kernel threads
+	 * from trying to save the FPU registers on context switch.
 	 */
-	memset(&dst_fpu->state.xsave, 0, fpu_kernel_xstate_size);
+	set_tsk_thread_flag(dst, TIF_NEED_FPU_LOAD);
 
 	/*
-	 * If the FPU registers are not owned by current just memcpy() the
-	 * state.  Otherwise save the FPU registers directly into the
-	 * child's FPU context, without any memory-to-memory copying.
+	 * No FPU state inheritance for kernel threads and IO
+	 * worker threads.
+	 */
+	if (dst->flags & (PF_KTHREAD | PF_IO_WORKER)) {
+		/* Clear out the minimal state */
+		memcpy(&dst_fpu->fpstate->regs, &init_fpstate.regs,
+		       init_fpstate_copy_size());
+		return 0;
+	}
+
+	/*
+	 * If a new feature is added, ensure all dynamic features are
+	 * caller-saved from here!
+	 */
+	BUILD_BUG_ON(XFEATURE_MASK_USER_DYNAMIC != XFEATURE_MASK_XTILE_DATA);
+
+	/*
+	 * Save the default portion of the current FPU state into the
+	 * clone. Assume all dynamic features to be defined as caller-
+	 * saved, which enables skipping both the expansion of fpstate
+	 * and the copying of any dynamic state.
+	 *
+	 * Do not use memcpy() when TIF_NEED_FPU_LOAD is set because
+	 * copying is not valid when current uses non-default states.
 	 */
 	fpregs_lock();
 	if (test_thread_flag(TIF_NEED_FPU_LOAD))
-		memcpy(&dst_fpu->state, &src_fpu->state, fpu_kernel_xstate_size);
-
-	else
-		save_fpregs_to_fpstate(dst_fpu);
+		fpregs_restore_userregs();
+	save_fpregs_to_fpstate(dst_fpu);
+	if (!(clone_flags & CLONE_THREAD))
+		fpu_inherit_perms(dst_fpu);
 	fpregs_unlock();
 
-	set_tsk_thread_flag(dst, TIF_NEED_FPU_LOAD);
-
 	trace_x86_fpu_copy_src(src_fpu);
 	trace_x86_fpu_copy_dst(dst_fpu);
 
@@ -287,6 +510,16 @@
 }
 
 /*
+ * Whitelist the FPU register state embedded into task_struct for hardened
+ * usercopy.
+ */
+void fpu_thread_struct_whitelist(unsigned long *offset, unsigned long *size)
+{
+	*offset = offsetof(struct thread_struct, fpu.__fpstate.regs);
+	*size = fpu_kernel_cfg.default_size;
+}
+
+/*
  * Drops current FPU state: deactivates the fpregs and
  * the fpstate. NOTE: it still leaves previous contents
  * in the fpregs in the eager-FPU case.
@@ -319,33 +552,24 @@
 static inline void restore_fpregs_from_init_fpstate(u64 features_mask)
 {
 	if (use_xsave())
-		os_xrstor(&init_fpstate.xsave, features_mask);
+		os_xrstor(&init_fpstate, features_mask);
 	else if (use_fxsr())
-		fxrstor(&init_fpstate.fxsave);
+		fxrstor(&init_fpstate.regs.fxsave);
 	else
-		frstor(&init_fpstate.fsave);
+		frstor(&init_fpstate.regs.fsave);
 
 	pkru_write_default();
 }
 
-static inline unsigned int init_fpstate_copy_size(void)
-{
-	if (!use_xsave())
-		return fpu_kernel_xstate_size;
-
-	/* XSAVE(S) just needs the legacy and the xstate header part */
-	return sizeof(init_fpstate.xsave);
-}
-
 /*
  * Reset current->fpu memory state to the init values.
  */
-static void fpu_reset_fpstate(void)
+static void fpu_reset_fpregs(void)
 {
 	struct fpu *fpu = &current->thread.fpu;
 
 	fpregs_lock();
-	fpu__drop(fpu);
+	__fpu_invalidate_fpregs_state(fpu);
 	/*
 	 * This does not change the actual hardware registers. It just
 	 * resets the memory image and sets TIF_NEED_FPU_LOAD so a
@@ -359,7 +583,7 @@
 	 * user space as PKRU is eagerly written in switch_to() and
 	 * flush_thread().
 	 */
-	memcpy(&fpu->state, &init_fpstate, init_fpstate_copy_size());
+	memcpy(&fpu->fpstate->regs, &init_fpstate.regs, init_fpstate_copy_size());
 	set_thread_flag(TIF_NEED_FPU_LOAD);
 	fpregs_unlock();
 }
@@ -375,7 +599,7 @@
 
 	fpregs_lock();
 	if (!cpu_feature_enabled(X86_FEATURE_FPU)) {
-		fpu_reset_fpstate();
+		fpu_reset_fpregs();
 		fpregs_unlock();
 		return;
 	}
@@ -385,12 +609,11 @@
 	 * corresponding registers.
 	 */
 	if (xfeatures_mask_supervisor() &&
-	    !fpregs_state_valid(fpu, smp_processor_id())) {
-		os_xrstor(&fpu->state.xsave, xfeatures_mask_supervisor());
-	}
+	    !fpregs_state_valid(fpu, smp_processor_id()))
+		os_xrstor_supervisor(fpu->fpstate);
 
 	/* Reset user states in registers. */
-	restore_fpregs_from_init_fpstate(xfeatures_mask_restore_user());
+	restore_fpregs_from_init_fpstate(XFEATURE_MASK_USER_RESTORE);
 
 	/*
 	 * Now all FPU registers have their desired values.  Inform the FPU
@@ -405,7 +628,8 @@
 
 void fpu_flush_thread(void)
 {
-	fpu_reset_fpstate();
+	fpstate_reset(&current->thread.fpu);
+	fpu_reset_fpregs();
 }
 /*
  * Load FPU context before returning to userspace.
@@ -445,7 +669,6 @@
 	fpu->last_cpu = smp_processor_id();
 	clear_thread_flag(TIF_NEED_FPU_LOAD);
 }
-EXPORT_SYMBOL_GPL(fpregs_mark_activate);
 
 /*
  * x87 math exception handling:
@@ -468,11 +691,11 @@
 		 * fully reproduce the context of the exception.
 		 */
 		if (boot_cpu_has(X86_FEATURE_FXSR)) {
-			cwd = fpu->state.fxsave.cwd;
-			swd = fpu->state.fxsave.swd;
+			cwd = fpu->fpstate->regs.fxsave.cwd;
+			swd = fpu->fpstate->regs.fxsave.swd;
 		} else {
-			cwd = (unsigned short)fpu->state.fsave.cwd;
-			swd = (unsigned short)fpu->state.fsave.swd;
+			cwd = (unsigned short)fpu->fpstate->regs.fsave.cwd;
+			swd = (unsigned short)fpu->fpstate->regs.fsave.swd;
 		}
 
 		err = swd & ~cwd;
@@ -486,7 +709,7 @@
 		unsigned short mxcsr = MXCSR_DEFAULT;
 
 		if (boot_cpu_has(X86_FEATURE_XMM))
-			mxcsr = fpu->state.fxsave.mxcsr;
+			mxcsr = fpu->fpstate->regs.fxsave.mxcsr;
 
 		err = ~(mxcsr >> 7) & mxcsr;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/init.c
@@ -2,7 +2,7 @@
 /*
  * x86 FPU boot time init code:
  */
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/tlbflush.h>
 #include <asm/setup.h>
 
@@ -10,6 +10,10 @@
 #include <linux/sched/task.h>
 #include <linux/init.h>
 
+#include "internal.h"
+#include "legacy.h"
+#include "xstate.h"
+
 /*
  * Initialize the registers found in all CPUs, CR0 and CR4:
  */
@@ -34,7 +38,7 @@
 	/* Flush out any pending x87 state: */
 #ifdef CONFIG_MATH_EMULATION
 	if (!boot_cpu_has(X86_FEATURE_FPU))
-		fpstate_init_soft(&current->thread.fpu.state.soft);
+		fpstate_init_soft(&current->thread.fpu.fpstate->regs.soft);
 	else
 #endif
 		asm volatile ("fninit");
@@ -49,7 +53,7 @@
 	fpu__init_cpu_xstate();
 }
 
-static bool fpu__probe_without_cpuid(void)
+static bool __init fpu__probe_without_cpuid(void)
 {
 	unsigned long cr0;
 	u16 fsw, fcw;
@@ -67,7 +71,7 @@
 	return fsw == 0 && (fcw & 0x103f) == 0x003f;
 }
 
-static void fpu__init_system_early_generic(struct cpuinfo_x86 *c)
+static void __init fpu__init_system_early_generic(void)
 {
 	if (!boot_cpu_has(X86_FEATURE_CPUID) &&
 	    !test_bit(X86_FEATURE_FPU, (unsigned long *)cpu_caps_cleared)) {
@@ -121,35 +125,23 @@
 static void __init fpu__init_system_generic(void)
 {
 	/*
-	 * Set up the legacy init FPU context. (xstate init might overwrite this
-	 * with a more modern format, if the CPU supports it.)
+	 * Set up the legacy init FPU context. Will be updated when the
+	 * CPU supports XSAVE[S].
 	 */
-	fpstate_init(&init_fpstate);
+	fpstate_init_user(&init_fpstate);
 
 	fpu__init_system_mxcsr();
 }
 
 /*
- * Size of the FPU context state. All tasks in the system use the
- * same context size, regardless of what portion they use.
- * This is inherent to the XSAVE architecture which puts all state
- * components into a single, continuous memory block:
- */
-unsigned int fpu_kernel_xstate_size __ro_after_init;
-EXPORT_SYMBOL_GPL(fpu_kernel_xstate_size);
-
-/* Get alignment of the TYPE. */
-#define TYPE_ALIGN(TYPE) offsetof(struct { char x; TYPE test; }, test)
-
-/*
  * Enforce that 'MEMBER' is the last field of 'TYPE'.
  *
  * Align the computed size with alignment of the TYPE,
  * because that's how C aligns structs.
  */
 #define CHECK_MEMBER_AT_END_OF(TYPE, MEMBER) \
-	BUILD_BUG_ON(sizeof(TYPE) != ALIGN(offsetofend(TYPE, MEMBER), \
-					   TYPE_ALIGN(TYPE)))
+	BUILD_BUG_ON(sizeof(TYPE) !=         \
+		     ALIGN(offsetofend(TYPE, MEMBER), _Alignof(TYPE)))
 
 /*
  * We append the 'struct fpu' to the task_struct:
@@ -162,13 +154,13 @@
 	 * Subtract off the static size of the register state.
 	 * It potentially has a bunch of padding.
 	 */
-	task_size -= sizeof(((struct task_struct *)0)->thread.fpu.state);
+	task_size -= sizeof(current->thread.fpu.__fpstate.regs);
 
 	/*
 	 * Add back the dynamically-calculated register state
 	 * size.
 	 */
-	task_size += fpu_kernel_xstate_size;
+	task_size += fpu_kernel_cfg.default_size;
 
 	/*
 	 * We dynamically size 'struct fpu', so we require that
@@ -177,7 +169,7 @@
 	 * you hit a compile error here, check the structure to
 	 * see if something got added to the end.
 	 */
-	CHECK_MEMBER_AT_END_OF(struct fpu, state);
+	CHECK_MEMBER_AT_END_OF(struct fpu, __fpstate);
 	CHECK_MEMBER_AT_END_OF(struct thread_struct, fpu);
 	CHECK_MEMBER_AT_END_OF(struct task_struct, thread);
 
@@ -192,46 +184,44 @@
  */
 static void __init fpu__init_system_xstate_size_legacy(void)
 {
-	static int on_boot_cpu __initdata = 1;
-
-	WARN_ON_FPU(!on_boot_cpu);
-	on_boot_cpu = 0;
+	unsigned int size;
 
 	/*
-	 * Note that xstate sizes might be overwritten later during
-	 * fpu__init_system_xstate().
+	 * Note that the size configuration might be overwritten later
+	 * during fpu__init_system_xstate().
 	 */
-
-	if (!boot_cpu_has(X86_FEATURE_FPU)) {
-		fpu_kernel_xstate_size = sizeof(struct swregs_state);
+	if (!cpu_feature_enabled(X86_FEATURE_FPU)) {
+		size = sizeof(struct swregs_state);
+	} else if (cpu_feature_enabled(X86_FEATURE_FXSR)) {
+		size = sizeof(struct fxregs_state);
+		fpu_user_cfg.legacy_features = XFEATURE_MASK_FPSSE;
 	} else {
-		if (boot_cpu_has(X86_FEATURE_FXSR))
-			fpu_kernel_xstate_size =
-				sizeof(struct fxregs_state);
-		else
-			fpu_kernel_xstate_size =
-				sizeof(struct fregs_state);
+		size = sizeof(struct fregs_state);
+		fpu_user_cfg.legacy_features = XFEATURE_MASK_FP;
 	}
 
-	fpu_user_xstate_size = fpu_kernel_xstate_size;
+	fpu_kernel_cfg.max_size = size;
+	fpu_kernel_cfg.default_size = size;
+	fpu_user_cfg.max_size = size;
+	fpu_user_cfg.default_size = size;
+	fpstate_reset(&current->thread.fpu);
 }
 
-/* Legacy code to initialize eager fpu mode. */
-static void __init fpu__init_system_ctx_switch(void)
-{
-	static bool on_boot_cpu __initdata = 1;
-
-	WARN_ON_FPU(!on_boot_cpu);
-	on_boot_cpu = 0;
+static void __init fpu__init_init_fpstate(void)
+{
+	/* Bring init_fpstate size and features up to date */
+	init_fpstate.size		= fpu_kernel_cfg.max_size;
+	init_fpstate.xfeatures		= fpu_kernel_cfg.max_features;
 }
 
 /*
  * Called on the boot CPU once per system bootup, to set up the initial
  * FPU state that is later cloned into all processes:
  */
-void __init fpu__init_system(struct cpuinfo_x86 *c)
+void __init fpu__init_system(void)
 {
-	fpu__init_system_early_generic(c);
+	fpstate_reset(&current->thread.fpu);
+	fpu__init_system_early_generic();
 
 	/*
 	 * The FPU has to be operational for some of the
@@ -241,8 +231,7 @@
 
 	fpu__init_system_generic();
 	fpu__init_system_xstate_size_legacy();
-	fpu__init_system_xstate();
+	fpu__init_system_xstate(fpu_kernel_cfg.max_size);
 	fpu__init_task_struct_size();
-
-	fpu__init_system_ctx_switch();
+	fpu__init_init_fpstate();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/internal.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/internal.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __X86_KERNEL_FPU_INTERNAL_H
+#define __X86_KERNEL_FPU_INTERNAL_H
+
+extern struct fpstate init_fpstate;
+
+/* CPU feature check wrappers */
+static __always_inline __pure bool use_xsave(void)
+{
+	return cpu_feature_enabled(X86_FEATURE_XSAVE);
+}
+
+static __always_inline __pure bool use_fxsr(void)
+{
+	return cpu_feature_enabled(X86_FEATURE_FXSR);
+}
+
+#ifdef CONFIG_X86_DEBUG_FPU
+# define WARN_ON_FPU(x) WARN_ON_ONCE(x)
+#else
+# define WARN_ON_FPU(x) ({ (void)(x); 0; })
+#endif
+
+/* Used in init.c */
+extern void fpstate_init_user(struct fpstate *fpstate);
+extern void fpstate_reset(struct fpu *fpu);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/legacy.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/legacy.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __X86_KERNEL_FPU_LEGACY_H
+#define __X86_KERNEL_FPU_LEGACY_H
+
+#include <asm/fpu/types.h>
+
+extern unsigned int mxcsr_feature_mask;
+
+static inline void ldmxcsr(u32 mxcsr)
+{
+	asm volatile("ldmxcsr %0" :: "m" (mxcsr));
+}
+
+/*
+ * Returns 0 on success or the trap number when the operation raises an
+ * exception.
+ */
+#define user_insn(insn, output, input...)				\
+({									\
+	int err;							\
+									\
+	might_fault();							\
+									\
+	asm volatile(ASM_STAC "\n"					\
+		     "1: " #insn "\n"					\
+		     "2: " ASM_CLAC "\n"				\
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_FAULT_MCE_SAFE)	\
+		     : [err] "=a" (err), output				\
+		     : "0"(0), input);					\
+	err;								\
+})
+
+#define kernel_insn_err(insn, output, input...)				\
+({									\
+	int err;							\
+	asm volatile("1:" #insn "\n\t"					\
+		     "2:\n"						\
+		     ".section .fixup,\"ax\"\n"				\
+		     "3:  movl $-1,%[err]\n"				\
+		     "    jmp  2b\n"					\
+		     ".previous\n"					\
+		     _ASM_EXTABLE(1b, 3b)				\
+		     : [err] "=r" (err), output				\
+		     : "0"(0), input);					\
+	err;								\
+})
+
+#define kernel_insn(insn, output, input...)				\
+	asm volatile("1:" #insn "\n\t"					\
+		     "2:\n"						\
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_FPU_RESTORE)	\
+		     : output : input)
+
+static inline int fnsave_to_user_sigframe(struct fregs_state __user *fx)
+{
+	return user_insn(fnsave %[fx]; fwait,  [fx] "=m" (*fx), "m" (*fx));
+}
+
+static inline int fxsave_to_user_sigframe(struct fxregs_state __user *fx)
+{
+	if (IS_ENABLED(CONFIG_X86_32))
+		return user_insn(fxsave %[fx], [fx] "=m" (*fx), "m" (*fx));
+	else
+		return user_insn(fxsaveq %[fx], [fx] "=m" (*fx), "m" (*fx));
+
+}
+
+static inline void fxrstor(struct fxregs_state *fx)
+{
+	if (IS_ENABLED(CONFIG_X86_32))
+		kernel_insn(fxrstor %[fx], "=m" (*fx), [fx] "m" (*fx));
+	else
+		kernel_insn(fxrstorq %[fx], "=m" (*fx), [fx] "m" (*fx));
+}
+
+static inline int fxrstor_safe(struct fxregs_state *fx)
+{
+	if (IS_ENABLED(CONFIG_X86_32))
+		return kernel_insn_err(fxrstor %[fx], "=m" (*fx), [fx] "m" (*fx));
+	else
+		return kernel_insn_err(fxrstorq %[fx], "=m" (*fx), [fx] "m" (*fx));
+}
+
+static inline int fxrstor_from_user_sigframe(struct fxregs_state __user *fx)
+{
+	if (IS_ENABLED(CONFIG_X86_32))
+		return user_insn(fxrstor %[fx], "=m" (*fx), [fx] "m" (*fx));
+	else
+		return user_insn(fxrstorq %[fx], "=m" (*fx), [fx] "m" (*fx));
+}
+
+static inline void frstor(struct fregs_state *fx)
+{
+	kernel_insn(frstor %[fx], "=m" (*fx), [fx] "m" (*fx));
+}
+
+static inline int frstor_safe(struct fregs_state *fx)
+{
+	return kernel_insn_err(frstor %[fx], "=m" (*fx), [fx] "m" (*fx));
+}
+
+static inline int frstor_from_user_sigframe(struct fregs_state __user *fx)
+{
+	return user_insn(frstor %[fx], "=m" (*fx), [fx] "m" (*fx));
+}
+
+static inline void fxsave(struct fxregs_state *fx)
+{
+	if (IS_ENABLED(CONFIG_X86_32))
+		asm volatile( "fxsave %[fx]" : [fx] "=m" (*fx));
+	else
+		asm volatile("fxsaveq %[fx]" : [fx] "=m" (*fx));
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/regset.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/regset.c
@@ -5,10 +5,14 @@
 #include <linux/sched/task_stack.h>
 #include <linux/vmalloc.h>
 
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/fpu/signal.h>
 #include <asm/fpu/regset.h>
-#include <asm/fpu/xstate.h>
+
+#include "context.h"
+#include "internal.h"
+#include "legacy.h"
+#include "xstate.h"
 
 /*
  * The xstateregs_active() routine is the same as the regset_fpregs_active() routine,
@@ -74,8 +78,8 @@
 	sync_fpstate(fpu);
 
 	if (!use_xsave()) {
-		return membuf_write(&to, &fpu->state.fxsave,
-				    sizeof(fpu->state.fxsave));
+		return membuf_write(&to, &fpu->fpstate->regs.fxsave,
+				    sizeof(fpu->fpstate->regs.fxsave));
 	}
 
 	copy_xstate_to_uabi_buf(to, target, XSTATE_COPY_FX);
@@ -87,11 +91,9 @@
 		const void *kbuf, const void __user *ubuf)
 {
 	struct fpu *fpu = &target->thread.fpu;
-	struct user32_fxsr_struct newstate;
+	struct fxregs_state newstate;
 	int ret;
 
-	BUILD_BUG_ON(sizeof(newstate) != sizeof(struct fxregs_state));
-
 	if (!cpu_feature_enabled(X86_FEATURE_FXSR))
 		return -ENODEV;
 
@@ -110,15 +112,16 @@
 	fpu_force_restore(fpu);
 
 	/* Copy the state  */
-	memcpy(&fpu->state.fxsave, &newstate, sizeof(newstate));
+	memcpy(&fpu->fpstate->regs.fxsave, &newstate, sizeof(newstate));
 
-	/* Clear xmm8..15 */
-	BUILD_BUG_ON(sizeof(fpu->state.fxsave.xmm_space) != 16 * 16);
-	memset(&fpu->state.fxsave.xmm_space[8], 0, 8 * 16);
+	/* Clear xmm8..15 for 32-bit callers */
+	BUILD_BUG_ON(sizeof(fpu->__fpstate.regs.fxsave.xmm_space) != 16 * 16);
+	if (in_ia32_syscall())
+		memset(&fpu->fpstate->regs.fxsave.xmm_space[8*4], 0, 8 * 16);
 
 	/* Mark FP and SSE as in use when XSAVE is enabled */
 	if (use_xsave())
-		fpu->state.xsave.header.xfeatures |= XFEATURE_MASK_FPSSE;
+		fpu->fpstate->regs.xsave.header.xfeatures |= XFEATURE_MASK_FPSSE;
 
 	return 0;
 }
@@ -149,7 +152,7 @@
 	/*
 	 * A whole standard-format XSAVE buffer is needed:
 	 */
-	if (pos != 0 || count != fpu_user_xstate_size)
+	if (pos != 0 || count != fpu_user_cfg.max_size)
 		return -EFAULT;
 
 	if (!kbuf) {
@@ -164,7 +167,7 @@
 	}
 
 	fpu_force_restore(fpu);
-	ret = copy_uabi_from_kernel_to_xstate(&fpu->state.xsave, kbuf ?: tmpbuf);
+	ret = copy_uabi_from_kernel_to_xstate(fpu->fpstate, kbuf ?: tmpbuf);
 
 out:
 	vfree(tmpbuf);
@@ -283,7 +286,7 @@
 void
 convert_from_fxsr(struct user_i387_ia32_struct *env, struct task_struct *tsk)
 {
-	__convert_from_fxsr(env, tsk, &tsk->thread.fpu.state.fxsave);
+	__convert_from_fxsr(env, tsk, &tsk->thread.fpu.fpstate->regs.fxsave);
 }
 
 void convert_to_fxsr(struct fxregs_state *fxsave,
@@ -326,7 +329,7 @@
 		return fpregs_soft_get(target, regset, to);
 
 	if (!cpu_feature_enabled(X86_FEATURE_FXSR)) {
-		return membuf_write(&to, &fpu->state.fsave,
+		return membuf_write(&to, &fpu->fpstate->regs.fsave,
 				    sizeof(struct fregs_state));
 	}
 
@@ -337,7 +340,7 @@
 		copy_xstate_to_uabi_buf(mb, target, XSTATE_COPY_FP);
 		fx = &fxsave;
 	} else {
-		fx = &fpu->state.fxsave;
+		fx = &fpu->fpstate->regs.fxsave;
 	}
 
 	__convert_from_fxsr(&env, target, fx);
@@ -366,16 +369,16 @@
 	fpu_force_restore(fpu);
 
 	if (cpu_feature_enabled(X86_FEATURE_FXSR))
-		convert_to_fxsr(&fpu->state.fxsave, &env);
+		convert_to_fxsr(&fpu->fpstate->regs.fxsave, &env);
 	else
-		memcpy(&fpu->state.fsave, &env, sizeof(env));
+		memcpy(&fpu->fpstate->regs.fsave, &env, sizeof(env));
 
 	/*
 	 * Update the header bit in the xsave header, indicating the
 	 * presence of FP.
 	 */
 	if (cpu_feature_enabled(X86_FEATURE_XSAVE))
-		fpu->state.xsave.header.xfeatures |= XFEATURE_MASK_FP;
+		fpu->fpstate->regs.xsave.header.xfeatures |= XFEATURE_MASK_FP;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/signal.c
@@ -7,23 +7,25 @@
 #include <linux/cpu.h>
 #include <linux/pagemap.h>
 
-#include <asm/fpu/internal.h>
 #include <asm/fpu/signal.h>
 #include <asm/fpu/regset.h>
 #include <asm/fpu/xstate.h>
 
 #include <asm/sigframe.h>
+#include <asm/trapnr.h>
 #include <asm/trace/fpu.h>
 
-static struct _fpx_sw_bytes fx_sw_reserved __ro_after_init;
-static struct _fpx_sw_bytes fx_sw_reserved_ia32 __ro_after_init;
+#include "context.h"
+#include "internal.h"
+#include "legacy.h"
+#include "xstate.h"
 
 /*
  * Check for the presence of extended state information in the
  * user fpstate pointer in the sigcontext.
  */
-static inline int check_xstate_in_sigframe(struct fxregs_state __user *fxbuf,
-					   struct _fpx_sw_bytes *fx_sw)
+static inline bool check_xstate_in_sigframe(struct fxregs_state __user *fxbuf,
+					    struct _fpx_sw_bytes *fx_sw)
 {
 	int min_xstate_size = sizeof(struct fxregs_state) +
 			      sizeof(struct xstate_header);
@@ -31,12 +33,12 @@
 	unsigned int magic2;
 
 	if (__copy_from_user(fx_sw, &fxbuf->sw_reserved[0], sizeof(*fx_sw)))
-		return -EFAULT;
+		return false;
 
 	/* Check for the first magic field and other error scenarios. */
 	if (fx_sw->magic1 != FP_XSTATE_MAGIC1 ||
 	    fx_sw->xstate_size < min_xstate_size ||
-	    fx_sw->xstate_size > fpu_user_xstate_size ||
+	    fx_sw->xstate_size > current->thread.fpu.fpstate->user_size ||
 	    fx_sw->xstate_size > fx_sw->extended_size)
 		goto setfx;
 
@@ -47,10 +49,10 @@
 	 * in the memory layout.
 	 */
 	if (__get_user(magic2, (__u32 __user *)(fpstate + fx_sw->xstate_size)))
-		return -EFAULT;
+		return false;
 
 	if (likely(magic2 == FP_XSTATE_MAGIC2))
-		return 0;
+		return true;
 setfx:
 	trace_x86_fpu_xstate_check_failed(&current->thread.fpu);
 
@@ -58,22 +60,22 @@
 	fx_sw->magic1 = 0;
 	fx_sw->xstate_size = sizeof(struct fxregs_state);
 	fx_sw->xfeatures = XFEATURE_MASK_FPSSE;
-	return 0;
+	return true;
 }
 
 /*
  * Signal frame handlers.
  */
-static inline int save_fsave_header(struct task_struct *tsk, void __user *buf)
+static inline bool save_fsave_header(struct task_struct *tsk, void __user *buf)
 {
 	if (use_fxsr()) {
-		struct xregs_state *xsave = &tsk->thread.fpu.state.xsave;
+		struct xregs_state *xsave = &tsk->thread.fpu.fpstate->regs.xsave;
 		struct user_i387_ia32_struct env;
 		struct _fpstate_32 __user *fp = buf;
 
 		fpregs_lock();
 		if (!test_thread_flag(TIF_NEED_FPU_LOAD))
-			fxsave(&tsk->thread.fpu.state.fxsave);
+			fxsave(&tsk->thread.fpu.fpstate->regs.fxsave);
 		fpregs_unlock();
 
 		convert_from_fxsr(&env, tsk);
@@ -81,33 +83,54 @@
 		if (__copy_to_user(buf, &env, sizeof(env)) ||
 		    __put_user(xsave->i387.swd, &fp->status) ||
 		    __put_user(X86_FXSR_MAGIC, &fp->magic))
-			return -1;
+			return false;
 	} else {
 		struct fregs_state __user *fp = buf;
 		u32 swd;
+
 		if (__get_user(swd, &fp->swd) || __put_user(swd, &fp->status))
-			return -1;
+			return false;
 	}
 
-	return 0;
+	return true;
+}
+
+/*
+ * Prepare the SW reserved portion of the fxsave memory layout, indicating
+ * the presence of the extended state information in the memory layout
+ * pointed to by the fpstate pointer in the sigcontext.
+ * This is saved when ever the FP and extended state context is
+ * saved on the user stack during the signal handler delivery to the user.
+ */
+static inline void save_sw_bytes(struct _fpx_sw_bytes *sw_bytes, bool ia32_frame,
+				 struct fpstate *fpstate)
+{
+	sw_bytes->magic1 = FP_XSTATE_MAGIC1;
+	sw_bytes->extended_size = fpstate->user_size + FP_XSTATE_MAGIC2_SIZE;
+	sw_bytes->xfeatures = fpstate->user_xfeatures;
+	sw_bytes->xstate_size = fpstate->user_size;
+
+	if (ia32_frame)
+		sw_bytes->extended_size += sizeof(struct fregs_state);
 }
 
-static inline int save_xstate_epilog(void __user *buf, int ia32_frame)
+static inline bool save_xstate_epilog(void __user *buf, int ia32_frame,
+				      struct fpstate *fpstate)
 {
 	struct xregs_state __user *x = buf;
-	struct _fpx_sw_bytes *sw_bytes;
+	struct _fpx_sw_bytes sw_bytes = {};
 	u32 xfeatures;
 	int err;
 
 	/* Setup the bytes not touched by the [f]xsave and reserved for SW. */
-	sw_bytes = ia32_frame ? &fx_sw_reserved_ia32 : &fx_sw_reserved;
-	err = __copy_to_user(&x->i387.sw_reserved, sw_bytes, sizeof(*sw_bytes));
+	save_sw_bytes(&sw_bytes, ia32_frame, fpstate);
+	err = __copy_to_user(&x->i387.sw_reserved, &sw_bytes, sizeof(sw_bytes));
 
 	if (!use_xsave())
-		return err;
+		return !err;
 
 	err |= __put_user(FP_XSTATE_MAGIC2,
-			  (__u32 __user *)(buf + fpu_user_xstate_size));
+			  (__u32 __user *)(buf + fpstate->user_size));
 
 	/*
 	 * Read the xfeatures which we copied (directly from the cpu or
@@ -130,23 +153,17 @@
 
 	err |= __put_user(xfeatures, (__u32 __user *)&x->header.xfeatures);
 
-	return err;
+	return !err;
 }
 
 static inline int copy_fpregs_to_sigframe(struct xregs_state __user *buf)
 {
-	int err;
-
 	if (use_xsave())
-		err = xsave_to_user_sigframe(buf);
-	else if (use_fxsr())
-		err = fxsave_to_user_sigframe((struct fxregs_state __user *) buf);
+		return xsave_to_user_sigframe(buf);
+	if (use_fxsr())
+		return fxsave_to_user_sigframe((struct fxregs_state __user *) buf);
 	else
-		err = fnsave_to_user_sigframe((struct fregs_state __user *) buf);
-
-	if (unlikely(err) && __clear_user(buf, fpu_user_xstate_size))
-		err = -EFAULT;
-	return err;
+		return fnsave_to_user_sigframe((struct fregs_state __user *) buf);
 }
 
 /*
@@ -159,10 +176,8 @@
  *	buf == buf_fx for 64-bit frames and 32-bit fsave frame.
  *	buf != buf_fx for 32-bit frames with fxstate.
  *
- * Try to save it directly to the user frame with disabled page fault handler.
- * If this fails then do the slow path where the FPU state is first saved to
- * task's fpu->state and then copy it to the user frame pointed to by the
- * aligned pointer 'buf_fx'.
+ * Save it directly to the user frame with disabled page fault handler. If
+ * that faults, try to clear the frame which handles the page fault.
  *
  * If this is a 32-bit frame with fxstate, put a fsave header before
  * the aligned state at 'buf_fx'.
@@ -170,10 +185,11 @@
  * For [f]xsave state, update the SW reserved fields in the [f]xsave frame
  * indicating the absence/presence of the extended state to the user.
  */
-int copy_fpstate_to_sigframe(void __user *buf, void __user *buf_fx, int size)
+bool copy_fpstate_to_sigframe(void __user *buf, void __user *buf_fx, int size)
 {
 	struct task_struct *tsk = current;
-	int ia32_fxstate = (buf != buf_fx);
+	struct fpstate *fpstate = tsk->thread.fpu.fpstate;
+	bool ia32_fxstate = (buf != buf_fx);
 	int ret;
 
 	ia32_fxstate &= (IS_ENABLED(CONFIG_X86_32) ||
@@ -181,13 +197,25 @@
 
 	if (!static_cpu_has(X86_FEATURE_FPU)) {
 		struct user_i387_ia32_struct fp;
+
 		fpregs_soft_get(current, NULL, (struct membuf){.p = &fp,
 						.left = sizeof(fp)});
-		return copy_to_user(buf, &fp, sizeof(fp)) ? -EFAULT : 0;
+		return !copy_to_user(buf, &fp, sizeof(fp));
 	}
 
 	if (!access_ok(buf, size))
-		return -EACCES;
+		return false;
+
+	if (use_xsave()) {
+		struct xregs_state __user *xbuf = buf_fx;
+
+		/*
+		 * Clear the xsave header first, so that reserved fields are
+		 * initialized to zero.
+		 */
+		if (__clear_user(&xbuf->header, sizeof(xbuf->header)))
+			return false;
+	}
 retry:
 	/*
 	 * Load the FPU registers if they are not valid for the current task.
@@ -205,26 +233,26 @@
 	fpregs_unlock();
 
 	if (ret) {
-		if (!fault_in_pages_writeable(buf_fx, fpu_user_xstate_size))
+		if (!__clear_user(buf_fx, fpstate->user_size))
 			goto retry;
-		return -EFAULT;
+		return false;
 	}
 
 	/* Save the fsave header for the 32-bit frames. */
-	if ((ia32_fxstate || !use_fxsr()) && save_fsave_header(tsk, buf))
-		return -1;
+	if ((ia32_fxstate || !use_fxsr()) && !save_fsave_header(tsk, buf))
+		return false;
 
-	if (use_fxsr() && save_xstate_epilog(buf_fx, ia32_fxstate))
-		return -1;
+	if (use_fxsr() && !save_xstate_epilog(buf_fx, ia32_fxstate, fpstate))
+		return false;
 
-	return 0;
+	return true;
 }
 
-static int __restore_fpregs_from_user(void __user *buf, u64 xrestore,
-				      bool fx_only)
+static int __restore_fpregs_from_user(void __user *buf, u64 ufeatures,
+				      u64 xrestore, bool fx_only)
 {
 	if (use_xsave()) {
-		u64 init_bv = xfeatures_mask_uabi() & ~xrestore;
+		u64 init_bv = ufeatures & ~xrestore;
 		int ret;
 
 		if (likely(!fx_only))
@@ -233,7 +261,7 @@
 			ret = fxrstor_from_user_sigframe(buf);
 
 		if (!ret && unlikely(init_bv))
-			os_xrstor(&init_fpstate.xsave, init_bv);
+			os_xrstor(&init_fpstate, init_bv);
 		return ret;
 	} else if (use_fxsr()) {
 		return fxrstor_from_user_sigframe(buf);
@@ -246,16 +274,20 @@
  * Attempt to restore the FPU registers directly from user memory.
  * Pagefaults are handled and any errors returned are fatal.
  */
-static int restore_fpregs_from_user(void __user *buf, u64 xrestore,
-				    bool fx_only, unsigned int size)
+static bool restore_fpregs_from_user(void __user *buf, u64 xrestore, bool fx_only)
 {
 	struct fpu *fpu = &current->thread.fpu;
 	int ret;
 
+	/* Restore enabled features only. */
+	xrestore &= fpu->fpstate->user_xfeatures;
 retry:
 	fpregs_lock();
+	/* Ensure that XFD is up to date */
+	xfd_update_state(fpu->fpstate);
 	pagefault_disable();
-	ret = __restore_fpregs_from_user(buf, xrestore, fx_only);
+	ret = __restore_fpregs_from_user(buf, fpu->fpstate->user_xfeatures,
+					 xrestore, fx_only);
 	pagefault_enable();
 
 	if (unlikely(ret)) {
@@ -275,13 +307,12 @@
 		fpregs_unlock();
 
 		/* Try to handle #PF, but anything else is fatal. */
-		if (ret != -EFAULT)
-			return -EINVAL;
+		if (ret != X86_TRAP_PF)
+			return false;
 
-		ret = fault_in_pages_readable(buf, size);
-		if (!ret)
+		if (!fault_in_readable(buf, fpu->fpstate->user_size))
 			goto retry;
-		return ret;
+		return false;
 	}
 
 	/*
@@ -294,47 +325,38 @@
 	 * been restored from a user buffer directly.
 	 */
 	if (test_thread_flag(TIF_NEED_FPU_LOAD) && xfeatures_mask_supervisor())
-		os_xrstor(&fpu->state.xsave, xfeatures_mask_supervisor());
+		os_xrstor_supervisor(fpu->fpstate);
 
 	fpregs_mark_activate();
 	fpregs_unlock();
-	return 0;
+	return true;
 }
 
-static int __fpu_restore_sig(void __user *buf, void __user *buf_fx,
-			     bool ia32_fxstate)
+static bool __fpu_restore_sig(void __user *buf, void __user *buf_fx,
+			      bool ia32_fxstate)
 {
-	int state_size = fpu_kernel_xstate_size;
 	struct task_struct *tsk = current;
 	struct fpu *fpu = &tsk->thread.fpu;
 	struct user_i387_ia32_struct env;
+	bool success, fx_only = false;
+	union fpregs_state *fpregs;
 	u64 user_xfeatures = 0;
-	bool fx_only = false;
-	int ret;
 
 	if (use_xsave()) {
 		struct _fpx_sw_bytes fx_sw_user;
 
-		ret = check_xstate_in_sigframe(buf_fx, &fx_sw_user);
-		if (unlikely(ret))
-			return ret;
+		if (!check_xstate_in_sigframe(buf_fx, &fx_sw_user))
+			return false;
 
 		fx_only = !fx_sw_user.magic1;
-		state_size = fx_sw_user.xstate_size;
 		user_xfeatures = fx_sw_user.xfeatures;
 	} else {
 		user_xfeatures = XFEATURE_MASK_FPSSE;
 	}
 
 	if (likely(!ia32_fxstate)) {
-		/*
-		 * Attempt to restore the FPU registers directly from user
-		 * memory. For that to succeed, the user access cannot cause page
-		 * faults. If it does, fall back to the slow path below, going
-		 * through the kernel buffer with the enabled pagefault handler.
-		 */
-		return restore_fpregs_from_user(buf_fx, user_xfeatures, fx_only,
-						state_size);
+		/* Restore the FPU registers directly from user memory. */
+		return restore_fpregs_from_user(buf_fx, user_xfeatures, fx_only);
 	}
 
 	/*
@@ -342,9 +364,8 @@
 	 * to be ignored for histerical raisins. The legacy state is folded
 	 * in once the larger state has been copied.
 	 */
-	ret = __copy_from_user(&env, buf, sizeof(env));
-	if (ret)
-		return ret;
+	if (__copy_from_user(&env, buf, sizeof(env)))
+		return false;
 
 	/*
 	 * By setting TIF_NEED_FPU_LOAD it is ensured that our xstate is
@@ -363,38 +384,38 @@
 		 * the right place in memory. It's ia32 mode. Shrug.
 		 */
 		if (xfeatures_mask_supervisor())
-			os_xsave(&fpu->state.xsave);
+			os_xsave(fpu->fpstate);
 		set_thread_flag(TIF_NEED_FPU_LOAD);
 	}
 	__fpu_invalidate_fpregs_state(fpu);
 	__cpu_invalidate_fpregs_state();
 	fpregs_unlock();
 
+	fpregs = &fpu->fpstate->regs;
 	if (use_xsave() && !fx_only) {
-		ret = copy_sigframe_from_user_to_xstate(&fpu->state.xsave, buf_fx);
-		if (ret)
-			return ret;
+		if (copy_sigframe_from_user_to_xstate(fpu->fpstate, buf_fx))
+			return false;
 	} else {
-		if (__copy_from_user(&fpu->state.fxsave, buf_fx,
-				     sizeof(fpu->state.fxsave)))
-			return -EFAULT;
+		if (__copy_from_user(&fpregs->fxsave, buf_fx,
+				     sizeof(fpregs->fxsave)))
+			return false;
 
 		if (IS_ENABLED(CONFIG_X86_64)) {
 			/* Reject invalid MXCSR values. */
-			if (fpu->state.fxsave.mxcsr & ~mxcsr_feature_mask)
-				return -EINVAL;
+			if (fpregs->fxsave.mxcsr & ~mxcsr_feature_mask)
+				return false;
 		} else {
 			/* Mask invalid bits out for historical reasons (broken hardware). */
-			fpu->state.fxsave.mxcsr &= mxcsr_feature_mask;
+			fpregs->fxsave.mxcsr &= mxcsr_feature_mask;
 		}
 
 		/* Enforce XFEATURE_MASK_FPSSE when XSAVE is enabled */
 		if (use_xsave())
-			fpu->state.xsave.header.xfeatures |= XFEATURE_MASK_FPSSE;
+			fpregs->xsave.header.xfeatures |= XFEATURE_MASK_FPSSE;
 	}
 
 	/* Fold the legacy FP storage */
-	convert_to_fxsr(&fpu->state.fxsave, &env);
+	convert_to_fxsr(&fpregs->fxsave, &env);
 
 	fpregs_lock();
 	if (use_xsave()) {
@@ -409,40 +430,45 @@
 		 */
 		u64 mask = user_xfeatures | xfeatures_mask_supervisor();
 
-		fpu->state.xsave.header.xfeatures &= mask;
-		ret = os_xrstor_safe(&fpu->state.xsave, xfeatures_mask_all);
+		fpregs->xsave.header.xfeatures &= mask;
+		success = !os_xrstor_safe(fpu->fpstate,
+					  fpu_kernel_cfg.max_features);
 	} else {
-		ret = fxrstor_safe(&fpu->state.fxsave);
+		success = !fxrstor_safe(&fpregs->fxsave);
 	}
 
-	if (likely(!ret))
+	if (likely(success))
 		fpregs_mark_activate();
 
 	fpregs_unlock();
-	return ret;
+	return success;
 }
-static inline int xstate_sigframe_size(void)
+
+static inline unsigned int xstate_sigframe_size(struct fpstate *fpstate)
 {
-	return use_xsave() ? fpu_user_xstate_size + FP_XSTATE_MAGIC2_SIZE :
-			fpu_user_xstate_size;
+	unsigned int size = fpstate->user_size;
+
+	return use_xsave() ? size + FP_XSTATE_MAGIC2_SIZE : size;
 }
 
 /*
  * Restore FPU state from a sigframe:
  */
-int fpu__restore_sig(void __user *buf, int ia32_frame)
+bool fpu__restore_sig(void __user *buf, int ia32_frame)
 {
-	unsigned int size = xstate_sigframe_size();
 	struct fpu *fpu = &current->thread.fpu;
 	void __user *buf_fx = buf;
 	bool ia32_fxstate = false;
-	int ret;
+	bool success = false;
+	unsigned int size;
 
 	if (unlikely(!buf)) {
 		fpu__clear_user_states(fpu);
-		return 0;
+		return true;
 	}
 
+	size = xstate_sigframe_size(fpu->fpstate);
+
 	ia32_frame &= (IS_ENABLED(CONFIG_X86_32) ||
 		       IS_ENABLED(CONFIG_IA32_EMULATION));
 
@@ -456,30 +482,28 @@
 		ia32_fxstate = true;
 	}
 
-	if (!access_ok(buf, size)) {
-		ret = -EACCES;
+	if (!access_ok(buf, size))
 		goto out;
-	}
 
 	if (!IS_ENABLED(CONFIG_X86_64) && !cpu_feature_enabled(X86_FEATURE_FPU)) {
-		ret = fpregs_soft_set(current, NULL, 0,
-				      sizeof(struct user_i387_ia32_struct),
-				      NULL, buf);
+		success = !fpregs_soft_set(current, NULL, 0,
+					   sizeof(struct user_i387_ia32_struct),
+					   NULL, buf);
 	} else {
-		ret = __fpu_restore_sig(buf, buf_fx, ia32_fxstate);
+		success = __fpu_restore_sig(buf, buf_fx, ia32_fxstate);
 	}
 
 out:
-	if (unlikely(ret))
+	if (unlikely(!success))
 		fpu__clear_user_states(fpu);
-	return ret;
+	return success;
 }
 
 unsigned long
 fpu__alloc_mathframe(unsigned long sp, int ia32_frame,
 		     unsigned long *buf_fx, unsigned long *size)
 {
-	unsigned long frame_size = xstate_sigframe_size();
+	unsigned long frame_size = xstate_sigframe_size(current->thread.fpu.fpstate);
 
 	*buf_fx = sp = round_down(sp - frame_size, 64);
 	if (ia32_frame && use_fxsr()) {
@@ -492,9 +516,12 @@
 	return sp;
 }
 
-unsigned long fpu__get_fpstate_size(void)
+unsigned long __init fpu__get_fpstate_size(void)
 {
-	unsigned long ret = xstate_sigframe_size();
+	unsigned long ret = fpu_user_cfg.max_size;
+
+	if (use_xsave())
+		ret += FP_XSTATE_MAGIC2_SIZE;
 
 	/*
 	 * This space is needed on (most) 32-bit kernels, or when a 32-bit
@@ -510,28 +537,3 @@
 	return ret;
 }
 
-/*
- * Prepare the SW reserved portion of the fxsave memory layout, indicating
- * the presence of the extended state information in the memory layout
- * pointed by the fpstate pointer in the sigcontext.
- * This will be saved when ever the FP and extended state context is
- * saved on the user stack during the signal handler delivery to the user.
- */
-void fpu__init_prepare_fx_sw_frame(void)
-{
-	int size = fpu_user_xstate_size + FP_XSTATE_MAGIC2_SIZE;
-
-	fx_sw_reserved.magic1 = FP_XSTATE_MAGIC1;
-	fx_sw_reserved.extended_size = size;
-	fx_sw_reserved.xfeatures = xfeatures_mask_uabi();
-	fx_sw_reserved.xstate_size = fpu_user_xstate_size;
-
-	if (IS_ENABLED(CONFIG_IA32_EMULATION) ||
-	    IS_ENABLED(CONFIG_X86_32)) {
-		int fsave_header_size = sizeof(struct fregs_state);
-
-		fx_sw_reserved_ia32 = fx_sw_reserved;
-		fx_sw_reserved_ia32.extended_size = size + fsave_header_size;
-	}
-}
-
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/xstate.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/xstate.c
@@ -4,21 +4,33 @@
  *
  * Author: Suresh Siddha <suresh.b.siddha@intel.com>
  */
+#include <linux/bitops.h>
 #include <linux/compat.h>
 #include <linux/cpu.h>
 #include <linux/mman.h>
+#include <linux/nospec.h>
 #include <linux/pkeys.h>
 #include <linux/seq_file.h>
 #include <linux/proc_fs.h>
+#include <linux/vmalloc.h>
 
 #include <asm/fpu/api.h>
-#include <asm/fpu/internal.h>
-#include <asm/fpu/signal.h>
 #include <asm/fpu/regset.h>
-#include <asm/fpu/xstate.h>
+#include <asm/fpu/signal.h>
+#include <asm/fpu/xcr.h>
 
 #include <asm/tlbflush.h>
-#include <asm/cpufeature.h>
+#include <asm/prctl.h>
+#include <asm/elf.h>
+
+#include "context.h"
+#include "internal.h"
+#include "legacy.h"
+#include "xstate.h"
+
+#define for_each_extended_xfeature(bit, mask)				\
+	(bit) = FIRST_EXTENDED_XFEATURE;				\
+	for_each_set_bit_from(bit, (unsigned long *)&(mask), 8 * sizeof(mask))
 
 /*
  * Although we spell it out in here, the Processor Trace
@@ -39,29 +51,32 @@
 	"Protection Keys User registers",
 	"PASID state",
 	"unknown xstate feature"	,
+	"unknown xstate feature"	,
+	"unknown xstate feature"	,
+	"unknown xstate feature"	,
+	"unknown xstate feature"	,
+	"unknown xstate feature"	,
+	"AMX Tile config"		,
+	"AMX Tile data"			,
+	"unknown xstate feature"	,
 };
 
-static short xsave_cpuid_features[] __initdata = {
-	X86_FEATURE_FPU,
-	X86_FEATURE_XMM,
-	X86_FEATURE_AVX,
-	X86_FEATURE_MPX,
-	X86_FEATURE_MPX,
-	X86_FEATURE_AVX512F,
-	X86_FEATURE_AVX512F,
-	X86_FEATURE_AVX512F,
-	X86_FEATURE_INTEL_PT,
-	X86_FEATURE_PKU,
-	X86_FEATURE_ENQCMD,
+static unsigned short xsave_cpuid_features[] __initdata = {
+	[XFEATURE_FP]				= X86_FEATURE_FPU,
+	[XFEATURE_SSE]				= X86_FEATURE_XMM,
+	[XFEATURE_YMM]				= X86_FEATURE_AVX,
+	[XFEATURE_BNDREGS]			= X86_FEATURE_MPX,
+	[XFEATURE_BNDCSR]			= X86_FEATURE_MPX,
+	[XFEATURE_OPMASK]			= X86_FEATURE_AVX512F,
+	[XFEATURE_ZMM_Hi256]			= X86_FEATURE_AVX512F,
+	[XFEATURE_Hi16_ZMM]			= X86_FEATURE_AVX512F,
+	[XFEATURE_PT_UNIMPLEMENTED_SO_FAR]	= X86_FEATURE_INTEL_PT,
+	[XFEATURE_PKRU]				= X86_FEATURE_PKU,
+	[XFEATURE_PASID]			= X86_FEATURE_ENQCMD,
+	[XFEATURE_XTILE_CFG]			= X86_FEATURE_AMX_TILE,
+	[XFEATURE_XTILE_DATA]			= X86_FEATURE_AMX_TILE,
 };
 
-/*
- * This represents the full set of bits that should ever be set in a kernel
- * XSAVE buffer, both supervisor and user xstates.
- */
-u64 xfeatures_mask_all __ro_after_init;
-EXPORT_SYMBOL_GPL(xfeatures_mask_all);
-
 static unsigned int xstate_offsets[XFEATURE_MAX] __ro_after_init =
 	{ [ 0 ... XFEATURE_MAX - 1] = -1};
 static unsigned int xstate_sizes[XFEATURE_MAX] __ro_after_init =
@@ -72,20 +87,13 @@
 	{ [ 0 ... XFEATURE_MAX - 1] = -1};
 
 /*
- * The XSAVE area of kernel can be in standard or compacted format;
- * it is always in standard format for user mode. This is the user
- * mode standard format size used for signal and ptrace frames.
- */
-unsigned int fpu_user_xstate_size __ro_after_init;
-
-/*
  * Return whether the system supports a given xfeature.
  *
  * Also return the name of the (most advanced) feature that the caller requested:
  */
 int cpu_has_xfeatures(u64 xfeatures_needed, const char **feature_name)
 {
-	u64 xfeatures_missing = xfeatures_needed & ~xfeatures_mask_all;
+	u64 xfeatures_missing = xfeatures_needed & ~fpu_kernel_cfg.max_features;
 
 	if (unlikely(feature_name)) {
 		long xfeature_idx, max_idx;
@@ -135,17 +143,26 @@
  */
 void fpu__init_cpu_xstate(void)
 {
-	if (!boot_cpu_has(X86_FEATURE_XSAVE) || !xfeatures_mask_all)
+	if (!boot_cpu_has(X86_FEATURE_XSAVE) || !fpu_kernel_cfg.max_features)
 		return;
 
 	cr4_set_bits(X86_CR4_OSXSAVE);
 
 	/*
+	 * Must happen after CR4 setup and before xsetbv() to allow KVM
+	 * lazy passthrough.  Write independent of the dynamic state static
+	 * key as that does not work on the boot CPU. This also ensures
+	 * that any stale state is wiped out from XFD.
+	 */
+	if (cpu_feature_enabled(X86_FEATURE_XFD))
+		wrmsrl(MSR_IA32_XFD, init_fpstate.xfd);
+
+	/*
 	 * XCR_XFEATURE_ENABLED_MASK (aka. XCR0) sets user features
 	 * managed by XSAVE{C, OPT, S} and XRSTOR{S}.  Only XSAVE user
 	 * states can be set here.
 	 */
-	xsetbv(XCR_XFEATURE_ENABLED_MASK, xfeatures_mask_uabi());
+	xsetbv(XCR_XFEATURE_ENABLED_MASK, fpu_user_cfg.max_features);
 
 	/*
 	 * MSR_IA32_XSS sets supervisor states managed by XSAVES.
@@ -158,7 +175,7 @@
 
 static bool xfeature_enabled(enum xfeature xfeature)
 {
-	return xfeatures_mask_all & BIT_ULL(xfeature);
+	return fpu_kernel_cfg.max_features & BIT_ULL(xfeature);
 }
 
 /*
@@ -184,10 +201,7 @@
 	xstate_sizes[XFEATURE_SSE]	= sizeof_field(struct fxregs_state,
 						       xmm_space);
 
-	for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-		if (!xfeature_enabled(i))
-			continue;
-
+	for_each_extended_xfeature(i, fpu_kernel_cfg.max_features) {
 		cpuid_count(XSTATE_CPUID, i, &eax, &ebx, &ecx, &edx);
 
 		xstate_sizes[i] = eax;
@@ -236,6 +250,8 @@
 	print_xstate_feature(XFEATURE_MASK_Hi16_ZMM);
 	print_xstate_feature(XFEATURE_MASK_PKRU);
 	print_xstate_feature(XFEATURE_MASK_PASID);
+	print_xstate_feature(XFEATURE_MASK_XTILE_CFG);
+	print_xstate_feature(XFEATURE_MASK_XTILE_DATA);
 }
 
 /*
@@ -291,20 +307,15 @@
 	xstate_comp_offsets[XFEATURE_SSE] = offsetof(struct fxregs_state,
 						     xmm_space);
 
-	if (!boot_cpu_has(X86_FEATURE_XSAVES)) {
-		for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-			if (xfeature_enabled(i))
-				xstate_comp_offsets[i] = xstate_offsets[i];
-		}
+	if (!cpu_feature_enabled(X86_FEATURE_XSAVES)) {
+		for_each_extended_xfeature(i, fpu_kernel_cfg.max_features)
+			xstate_comp_offsets[i] = xstate_offsets[i];
 		return;
 	}
 
 	next_offset = FXSAVE_SIZE + XSAVE_HDR_SIZE;
 
-	for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-		if (!xfeature_enabled(i))
-			continue;
-
+	for_each_extended_xfeature(i, fpu_kernel_cfg.max_features) {
 		if (xfeature_is_aligned(i))
 			next_offset = ALIGN(next_offset, 64);
 
@@ -328,8 +339,8 @@
 
 	next_offset = FXSAVE_SIZE + XSAVE_HDR_SIZE;
 
-	for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-		if (!xfeature_enabled(i) || !xfeature_is_supervisor(i))
+	for_each_extended_xfeature(i, fpu_kernel_cfg.max_features) {
+		if (!xfeature_is_supervisor(i))
 			continue;
 
 		if (xfeature_is_aligned(i))
@@ -347,15 +358,36 @@
 {
 	int i;
 
-	for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-		if (!xfeature_enabled(i))
-			continue;
+	for_each_extended_xfeature(i, fpu_kernel_cfg.max_features) {
 		pr_info("x86/fpu: xstate_offset[%d]: %4d, xstate_sizes[%d]: %4d\n",
 			 i, xstate_comp_offsets[i], i, xstate_sizes[i]);
 	}
 }
 
 /*
+ * This function is called only during boot time when x86 caps are not set
+ * up and alternative can not be used yet.
+ */
+static __init void os_xrstor_booting(struct xregs_state *xstate)
+{
+	u64 mask = fpu_kernel_cfg.max_features & XFEATURE_MASK_FPSTATE;
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+	int err;
+
+	if (cpu_feature_enabled(X86_FEATURE_XSAVES))
+		XSTATE_OP(XRSTORS, xstate, lmask, hmask, err);
+	else
+		XSTATE_OP(XRSTOR, xstate, lmask, hmask, err);
+
+	/*
+	 * We should never fault when copying from a kernel buffer, and the FPU
+	 * state we set at boot time should be valid.
+	 */
+	WARN_ON_FPU(err);
+}
+
+/*
  * All supported features have either init state all zeros or are
  * handled in setup_init_fpu() individually. This is an explicit
  * feature list and does not use XFEATURE_MASK*SUPPORTED to catch
@@ -372,36 +404,30 @@
 	 XFEATURE_MASK_PKRU |			\
 	 XFEATURE_MASK_BNDREGS |		\
 	 XFEATURE_MASK_BNDCSR |			\
-	 XFEATURE_MASK_PASID)
+	 XFEATURE_MASK_PASID |			\
+	 XFEATURE_MASK_XTILE)
 
 /*
  * setup the xstate image representing the init state
  */
 static void __init setup_init_fpu_buf(void)
 {
-	static int on_boot_cpu __initdata = 1;
-
 	BUILD_BUG_ON((XFEATURE_MASK_USER_SUPPORTED |
 		      XFEATURE_MASK_SUPERVISOR_SUPPORTED) !=
 		     XFEATURES_INIT_FPSTATE_HANDLED);
 
-	WARN_ON_FPU(!on_boot_cpu);
-	on_boot_cpu = 0;
-
 	if (!boot_cpu_has(X86_FEATURE_XSAVE))
 		return;
 
 	setup_xstate_features();
 	print_xstate_features();
 
-	if (boot_cpu_has(X86_FEATURE_XSAVES))
-		init_fpstate.xsave.header.xcomp_bv = XCOMP_BV_COMPACTED_FORMAT |
-						     xfeatures_mask_all;
+	xstate_init_xcomp_bv(&init_fpstate.regs.xsave, fpu_kernel_cfg.max_features);
 
 	/*
 	 * Init all the features state with header.xfeatures being 0x0
 	 */
-	os_xrstor_booting(&init_fpstate.xsave);
+	os_xrstor_booting(&init_fpstate.regs.xsave);
 
 	/*
 	 * All components are now in init state. Read the state back so
@@ -419,7 +445,7 @@
 	 * state is all zeroes or if not to add the necessary handling
 	 * here.
 	 */
-	fxsave(&init_fpstate.fxsave);
+	fxsave(&init_fpstate.regs.fxsave);
 }
 
 static int xfeature_uncompacted_offset(int xfeature_nr)
@@ -451,10 +477,11 @@
 }
 
 /* Validate an xstate header supplied by userspace (ptrace or sigreturn) */
-static int validate_user_xstate_header(const struct xstate_header *hdr)
+static int validate_user_xstate_header(const struct xstate_header *hdr,
+				       struct fpstate *fpstate)
 {
 	/* No unknown or supervisor features may be set */
-	if (hdr->xfeatures & ~xfeatures_mask_uabi())
+	if (hdr->xfeatures & ~fpstate->user_xfeatures)
 		return -EINVAL;
 
 	/* Userspace must use the uncompacted format */
@@ -474,7 +501,7 @@
 	return 0;
 }
 
-static void __xstate_dump_leaves(void)
+static void __init __xstate_dump_leaves(void)
 {
 	int i;
 	u32 eax, ebx, ecx, edx;
@@ -509,12 +536,73 @@
 	}								\
 } while (0)
 
+/**
+ * check_xtile_data_against_struct - Check tile data state size.
+ *
+ * Calculate the state size by multiplying the single tile size which is
+ * recorded in a C struct, and the number of tiles that the CPU informs.
+ * Compare the provided size with the calculation.
+ *
+ * @size:	The tile data state size
+ *
+ * Returns:	0 on success, -EINVAL on mismatch.
+ */
+static int __init check_xtile_data_against_struct(int size)
+{
+	u32 max_palid, palid, state_size;
+	u32 eax, ebx, ecx, edx;
+	u16 max_tile;
+
+	/*
+	 * Check the maximum palette id:
+	 *   eax: the highest numbered palette subleaf.
+	 */
+	cpuid_count(TILE_CPUID, 0, &max_palid, &ebx, &ecx, &edx);
+
+	/*
+	 * Cross-check each tile size and find the maximum number of
+	 * supported tiles.
+	 */
+	for (palid = 1, max_tile = 0; palid <= max_palid; palid++) {
+		u16 tile_size, max;
+
+		/*
+		 * Check the tile size info:
+		 *   eax[31:16]:  bytes per title
+		 *   ebx[31:16]:  the max names (or max number of tiles)
+		 */
+		cpuid_count(TILE_CPUID, palid, &eax, &ebx, &edx, &edx);
+		tile_size = eax >> 16;
+		max = ebx >> 16;
+
+		if (tile_size != sizeof(struct xtile_data)) {
+			pr_err("%s: struct is %zu bytes, cpu xtile %d bytes\n",
+			       __stringify(XFEATURE_XTILE_DATA),
+			       sizeof(struct xtile_data), tile_size);
+			__xstate_dump_leaves();
+			return -EINVAL;
+		}
+
+		if (max > max_tile)
+			max_tile = max;
+	}
+
+	state_size = sizeof(struct xtile_data) * max_tile;
+	if (size != state_size) {
+		pr_err("%s: calculated size is %u bytes, cpu state %d bytes\n",
+		       __stringify(XFEATURE_XTILE_DATA), state_size, size);
+		__xstate_dump_leaves();
+		return -EINVAL;
+	}
+	return 0;
+}
+
 /*
  * We have a C struct for each 'xstate'.  We need to ensure
  * that our software representation matches what the CPU
  * tells us about the state's size.
  */
-static void check_xstate_against_struct(int nr)
+static bool __init check_xstate_against_struct(int nr)
 {
 	/*
 	 * Ask the CPU for the size of the state.
@@ -532,6 +620,11 @@
 	XCHECK_SZ(sz, nr, XFEATURE_Hi16_ZMM,  struct avx_512_hi16_state);
 	XCHECK_SZ(sz, nr, XFEATURE_PKRU,      struct pkru_state);
 	XCHECK_SZ(sz, nr, XFEATURE_PASID,     struct ia32_pasid_state);
+	XCHECK_SZ(sz, nr, XFEATURE_XTILE_CFG, struct xtile_cfg);
+
+	/* The tile data size varies between implementations. */
+	if (nr == XFEATURE_XTILE_DATA)
+		check_xtile_data_against_struct(sz);
 
 	/*
 	 * Make *SURE* to add any feature numbers in below if
@@ -541,10 +634,39 @@
 	if ((nr < XFEATURE_YMM) ||
 	    (nr >= XFEATURE_MAX) ||
 	    (nr == XFEATURE_PT_UNIMPLEMENTED_SO_FAR) ||
-	    ((nr >= XFEATURE_RSRVD_COMP_11) && (nr <= XFEATURE_LBR))) {
+	    ((nr >= XFEATURE_RSRVD_COMP_11) && (nr <= XFEATURE_RSRVD_COMP_16))) {
 		WARN_ONCE(1, "no structure for xstate: %d\n", nr);
 		XSTATE_WARN_ON(1);
+		return false;
 	}
+	return true;
+}
+
+static unsigned int xstate_calculate_size(u64 xfeatures, bool compacted)
+{
+	unsigned int size = FXSAVE_SIZE + XSAVE_HDR_SIZE;
+	int i;
+
+	for_each_extended_xfeature(i, xfeatures) {
+		/* Align from the end of the previous feature */
+		if (xfeature_is_aligned(i))
+			size = ALIGN(size, 64);
+		/*
+		 * In compacted format the enabled features are packed,
+		 * i.e. disabled features do not occupy space.
+		 *
+		 * In non-compacted format the offsets are fixed and
+		 * disabled states still occupy space in the memory buffer.
+		 */
+		if (!compacted)
+			size = xfeature_uncompacted_offset(i);
+		/*
+		 * Add the feature size even for non-compacted format
+		 * to make the end result correct
+		 */
+		size += xfeature_size(i);
+	}
+	return size;
 }
 
 /*
@@ -556,44 +678,29 @@
  * covered by these checks. Only the size of the buffer for task->fpu
  * is checked here.
  */
-static void do_extra_xstate_size_checks(void)
+static bool __init paranoid_xstate_size_valid(unsigned int kernel_size)
 {
-	int paranoid_xstate_size = FXSAVE_SIZE + XSAVE_HDR_SIZE;
+	bool compacted = cpu_feature_enabled(X86_FEATURE_XSAVES);
+	unsigned int size = FXSAVE_SIZE + XSAVE_HDR_SIZE;
 	int i;
 
-	for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-		if (!xfeature_enabled(i))
-			continue;
-
-		check_xstate_against_struct(i);
+	for_each_extended_xfeature(i, fpu_kernel_cfg.max_features) {
+		if (!check_xstate_against_struct(i))
+			return false;
 		/*
 		 * Supervisor state components can be managed only by
 		 * XSAVES.
 		 */
-		if (!cpu_feature_enabled(X86_FEATURE_XSAVES))
-			XSTATE_WARN_ON(xfeature_is_supervisor(i));
-
-		/* Align from the end of the previous feature */
-		if (xfeature_is_aligned(i))
-			paranoid_xstate_size = ALIGN(paranoid_xstate_size, 64);
-		/*
-		 * The offset of a given state in the non-compacted
-		 * format is given to us in a CPUID leaf.  We check
-		 * them for being ordered (increasing offsets) in
-		 * setup_xstate_features(). XSAVES uses compacted format.
-		 */
-		if (!cpu_feature_enabled(X86_FEATURE_XSAVES))
-			paranoid_xstate_size = xfeature_uncompacted_offset(i);
-		/*
-		 * The compacted-format offset always depends on where
-		 * the previous state ended.
-		 */
-		paranoid_xstate_size += xfeature_size(i);
+		if (!compacted && xfeature_is_supervisor(i)) {
+			XSTATE_WARN_ON(1);
+			return false;
+		}
 	}
-	XSTATE_WARN_ON(paranoid_xstate_size != fpu_kernel_xstate_size);
+	size = xstate_calculate_size(fpu_kernel_cfg.max_features, compacted);
+	XSTATE_WARN_ON(size != kernel_size);
+	return size == kernel_size;
 }
 
-
 /*
  * Get total size of enabled xstates in XCR0 | IA32_XSS.
  *
@@ -644,7 +751,7 @@
 	return size;
 }
 
-static unsigned int __init get_xsave_size(void)
+static unsigned int __init get_xsave_size_user(void)
 {
 	unsigned int eax, ebx, ecx, edx;
 	/*
@@ -662,44 +769,54 @@
  * Will the runtime-enumerated 'xstate_size' fit in the init
  * task's statically-allocated buffer?
  */
-static bool is_supported_xstate_size(unsigned int test_xstate_size)
+static bool __init is_supported_xstate_size(unsigned int test_xstate_size)
 {
-	if (test_xstate_size <= sizeof(union fpregs_state))
+	if (test_xstate_size <= sizeof(init_fpstate.regs))
 		return true;
 
 	pr_warn("x86/fpu: xstate buffer too small (%zu < %d), disabling xsave\n",
-			sizeof(union fpregs_state), test_xstate_size);
+			sizeof(init_fpstate.regs), test_xstate_size);
 	return false;
 }
 
 static int __init init_xstate_size(void)
 {
 	/* Recompute the context size for enabled features: */
-	unsigned int possible_xstate_size;
-	unsigned int xsave_size;
+	unsigned int user_size, kernel_size, kernel_default_size;
+	bool compacted = cpu_feature_enabled(X86_FEATURE_XSAVES);
 
-	xsave_size = get_xsave_size();
+	/* Uncompacted user space size */
+	user_size = get_xsave_size_user();
 
-	if (boot_cpu_has(X86_FEATURE_XSAVES))
-		possible_xstate_size = get_xsaves_size_no_independent();
+	/*
+	 * XSAVES kernel size includes supervisor states and
+	 * uses compacted format when available.
+	 *
+	 * XSAVE does not support supervisor states so
+	 * kernel and user size is identical.
+	 */
+	if (compacted)
+		kernel_size = get_xsaves_size_no_independent();
 	else
-		possible_xstate_size = xsave_size;
+		kernel_size = user_size;
 
-	/* Ensure we have the space to store all enabled: */
-	if (!is_supported_xstate_size(possible_xstate_size))
+	kernel_default_size =
+		xstate_calculate_size(fpu_kernel_cfg.default_features, compacted);
+
+	/* Ensure we have the space to store all default enabled features. */
+	if (!is_supported_xstate_size(kernel_default_size))
 		return -EINVAL;
 
-	/*
-	 * The size is OK, we are definitely going to use xsave,
-	 * make it known to the world that we need more space.
-	 */
-	fpu_kernel_xstate_size = possible_xstate_size;
-	do_extra_xstate_size_checks();
+	if (!paranoid_xstate_size_valid(kernel_size))
+		return -EINVAL;
+
+	fpu_kernel_cfg.max_size = kernel_size;
+	fpu_user_cfg.max_size = user_size;
+
+	fpu_kernel_cfg.default_size = kernel_default_size;
+	fpu_user_cfg.default_size =
+		xstate_calculate_size(fpu_user_cfg.default_features, false);
 
-	/*
-	 * User space is always in standard format.
-	 */
-	fpu_user_xstate_size = xsave_size;
 	return 0;
 }
 
@@ -707,28 +824,38 @@
  * We enabled the XSAVE hardware, but something went wrong and
  * we can not use it.  Disable it.
  */
-static void fpu__init_disable_system_xstate(void)
+static void __init fpu__init_disable_system_xstate(unsigned int legacy_size)
 {
-	xfeatures_mask_all = 0;
+	fpu_kernel_cfg.max_features = 0;
 	cr4_clear_bits(X86_CR4_OSXSAVE);
 	setup_clear_cpu_cap(X86_FEATURE_XSAVE);
+
+	/* Restore the legacy size.*/
+	fpu_kernel_cfg.max_size = legacy_size;
+	fpu_kernel_cfg.default_size = legacy_size;
+	fpu_user_cfg.max_size = legacy_size;
+	fpu_user_cfg.default_size = legacy_size;
+
+	/*
+	 * Prevent enabling the static branch which enables writes to the
+	 * XFD MSR.
+	 */
+	init_fpstate.xfd = 0;
+
+	fpstate_reset(&current->thread.fpu);
 }
 
 /*
  * Enable and initialize the xsave feature.
  * Called once per system bootup.
  */
-void __init fpu__init_system_xstate(void)
+void __init fpu__init_system_xstate(unsigned int legacy_size)
 {
 	unsigned int eax, ebx, ecx, edx;
-	static int on_boot_cpu __initdata = 1;
 	u64 xfeatures;
 	int err;
 	int i;
 
-	WARN_ON_FPU(!on_boot_cpu);
-	on_boot_cpu = 0;
-
 	if (!boot_cpu_has(X86_FEATURE_FPU)) {
 		pr_info("x86/fpu: No FPU detected\n");
 		return;
@@ -749,38 +876,65 @@
 	 * Find user xstates supported by the processor.
 	 */
 	cpuid_count(XSTATE_CPUID, 0, &eax, &ebx, &ecx, &edx);
-	xfeatures_mask_all = eax + ((u64)edx << 32);
+	fpu_kernel_cfg.max_features = eax + ((u64)edx << 32);
 
 	/*
 	 * Find supervisor xstates supported by the processor.
 	 */
 	cpuid_count(XSTATE_CPUID, 1, &eax, &ebx, &ecx, &edx);
-	xfeatures_mask_all |= ecx + ((u64)edx << 32);
+	fpu_kernel_cfg.max_features |= ecx + ((u64)edx << 32);
 
-	if ((xfeatures_mask_uabi() & XFEATURE_MASK_FPSSE) != XFEATURE_MASK_FPSSE) {
+	if ((fpu_kernel_cfg.max_features & XFEATURE_MASK_FPSSE) != XFEATURE_MASK_FPSSE) {
 		/*
 		 * This indicates that something really unexpected happened
 		 * with the enumeration.  Disable XSAVE and try to continue
 		 * booting without it.  This is too early to BUG().
 		 */
 		pr_err("x86/fpu: FP/SSE not present amongst the CPU's xstate features: 0x%llx.\n",
-		       xfeatures_mask_all);
+		       fpu_kernel_cfg.max_features);
 		goto out_disable;
 	}
 
+	fpu_kernel_cfg.independent_features = fpu_kernel_cfg.max_features &
+					      XFEATURE_MASK_INDEPENDENT;
+
 	/*
 	 * Clear XSAVE features that are disabled in the normal CPUID.
 	 */
 	for (i = 0; i < ARRAY_SIZE(xsave_cpuid_features); i++) {
-		if (!boot_cpu_has(xsave_cpuid_features[i]))
-			xfeatures_mask_all &= ~BIT_ULL(i);
+		unsigned short cid = xsave_cpuid_features[i];
+
+		/* Careful: X86_FEATURE_FPU is 0! */
+		if ((i != XFEATURE_FP && !cid) || !boot_cpu_has(cid))
+			fpu_kernel_cfg.max_features &= ~BIT_ULL(i);
 	}
 
-	xfeatures_mask_all &= XFEATURE_MASK_USER_SUPPORTED |
+	if (!cpu_feature_enabled(X86_FEATURE_XFD))
+		fpu_kernel_cfg.max_features &= ~XFEATURE_MASK_USER_DYNAMIC;
+
+	fpu_kernel_cfg.max_features &= XFEATURE_MASK_USER_SUPPORTED |
 			      XFEATURE_MASK_SUPERVISOR_SUPPORTED;
 
+	fpu_user_cfg.max_features = fpu_kernel_cfg.max_features;
+	fpu_user_cfg.max_features &= XFEATURE_MASK_USER_SUPPORTED;
+
+	/* Clean out dynamic features from default */
+	fpu_kernel_cfg.default_features = fpu_kernel_cfg.max_features;
+	fpu_kernel_cfg.default_features &= ~XFEATURE_MASK_USER_DYNAMIC;
+
+	fpu_user_cfg.default_features = fpu_user_cfg.max_features;
+	fpu_user_cfg.default_features &= ~XFEATURE_MASK_USER_DYNAMIC;
+
 	/* Store it for paranoia check at the end */
-	xfeatures = xfeatures_mask_all;
+	xfeatures = fpu_kernel_cfg.max_features;
+
+	/*
+	 * Initialize the default XFD state in initfp_state and enable the
+	 * dynamic sizing mechanism if dynamic states are available.  The
+	 * static key cannot be enabled here because this runs before
+	 * jump_label_init(). This is delayed to an initcall.
+	 */
+	init_fpstate.xfd = fpu_user_cfg.max_features & XFEATURE_MASK_USER_DYNAMIC;
 
 	/* Enable xstate instructions to be able to continue with initialization: */
 	fpu__init_cpu_xstate();
@@ -788,13 +942,16 @@
 	if (err)
 		goto out_disable;
 
+	/* Reset the state for the current task */
+	fpstate_reset(&current->thread.fpu);
+
 	/*
 	 * Update info used for ptrace frames; use standard-format size and no
 	 * supervisor xstates:
 	 */
-	update_regset_xstate_info(fpu_user_xstate_size, xfeatures_mask_uabi());
+	update_regset_xstate_info(fpu_user_cfg.max_size,
+				  fpu_user_cfg.max_features);
 
-	fpu__init_prepare_fx_sw_frame();
 	setup_init_fpu_buf();
 	setup_xstate_comp_offsets();
 	setup_supervisor_only_offsets();
@@ -803,22 +960,29 @@
 	 * Paranoia check whether something in the setup modified the
 	 * xfeatures mask.
 	 */
-	if (xfeatures != xfeatures_mask_all) {
+	if (xfeatures != fpu_kernel_cfg.max_features) {
 		pr_err("x86/fpu: xfeatures modified from 0x%016llx to 0x%016llx during init, disabling XSAVE\n",
-		       xfeatures, xfeatures_mask_all);
+		       xfeatures, fpu_kernel_cfg.max_features);
 		goto out_disable;
 	}
 
+	/*
+	 * CPU capabilities initialization runs before FPU init. So
+	 * X86_FEATURE_OSXSAVE is not set. Now that XSAVE is completely
+	 * functional, set the feature bit so depending code works.
+	 */
+	setup_force_cpu_cap(X86_FEATURE_OSXSAVE);
+
 	print_xstate_offset_size();
 	pr_info("x86/fpu: Enabled xstate features 0x%llx, context size is %d bytes, using '%s' format.\n",
-		xfeatures_mask_all,
-		fpu_kernel_xstate_size,
+		fpu_kernel_cfg.max_features,
+		fpu_kernel_cfg.max_size,
 		boot_cpu_has(X86_FEATURE_XSAVES) ? "compacted" : "standard");
 	return;
 
 out_disable:
 	/* something went wrong, try to boot without any XSAVE support */
-	fpu__init_disable_system_xstate();
+	fpu__init_disable_system_xstate(legacy_size);
 }
 
 /*
@@ -830,7 +994,7 @@
 	 * Restore XCR0 on xsave capable CPUs:
 	 */
 	if (cpu_feature_enabled(X86_FEATURE_XSAVE))
-		xsetbv(XCR_XFEATURE_ENABLED_MASK, xfeatures_mask_uabi());
+		xsetbv(XCR_XFEATURE_ENABLED_MASK, fpu_user_cfg.max_features);
 
 	/*
 	 * Restore IA32_XSS. The same CPUID bit enumerates support
@@ -840,6 +1004,9 @@
 		wrmsrl(MSR_IA32_XSS, xfeatures_mask_supervisor()  |
 				     xfeatures_mask_independent());
 	}
+
+	if (fpu_state_size_dynamic())
+		wrmsrl(MSR_IA32_XFD, current->thread.fpu.fpstate->xfd);
 }
 
 /*
@@ -886,7 +1053,7 @@
 	 * We should not ever be requesting features that we
 	 * have not enabled.
 	 */
-	WARN_ONCE(!(xfeatures_mask_all & BIT_ULL(xfeature_nr)),
+	WARN_ONCE(!(fpu_kernel_cfg.max_features & BIT_ULL(xfeature_nr)),
 		  "get of unsupported state");
 	/*
 	 * This assumes the last 'xsave*' instruction to
@@ -904,7 +1071,6 @@
 
 	return __raw_xsave_addr(xsave, xfeature_nr);
 }
-EXPORT_SYMBOL_GPL(get_xsave_addr);
 
 #ifdef CONFIG_ARCH_HAS_PKEYS
 
@@ -961,9 +1127,11 @@
 }
 
 /**
- * copy_xstate_to_uabi_buf - Copy kernel saved xstate to a UABI buffer
+ * __copy_xstate_to_uabi_buf - Copy kernel saved xstate to a UABI buffer
  * @to:		membuf descriptor
- * @tsk:	The task from which to copy the saved xstate
+ * @fpstate:	The fpstate buffer from which to copy
+ * @xfeatures:	The mask of xfeatures to save (XSAVE mode only)
+ * @pkru_val:	The PKRU value to store in the PKRU component
  * @copy_mode:	The requested copy mode
  *
  * Converts from kernel XSAVE or XSAVES compacted format to UABI conforming
@@ -972,14 +1140,16 @@
  *
  * It supports partial copy but @to.pos always starts from zero.
  */
-void copy_xstate_to_uabi_buf(struct membuf to, struct task_struct *tsk,
-			     enum xstate_copy_mode copy_mode)
+void __copy_xstate_to_uabi_buf(struct membuf to, struct fpstate *fpstate,
+			       u64 xfeatures, u32 pkru_val,
+			       enum xstate_copy_mode copy_mode)
 {
 	const unsigned int off_mxcsr = offsetof(struct fxregs_state, mxcsr);
-	struct xregs_state *xsave = &tsk->thread.fpu.state.xsave;
-	struct xregs_state *xinit = &init_fpstate.xsave;
+	struct xregs_state *xinit = &init_fpstate.regs.xsave;
+	struct xregs_state *xsave = &fpstate->regs.xsave;
 	struct xstate_header header;
 	unsigned int zerofrom;
+	u64 mask;
 	int i;
 
 	memset(&header, 0, sizeof(header));
@@ -996,7 +1166,7 @@
 		break;
 
 	case XSTATE_COPY_XSAVE:
-		header.xfeatures &= xfeatures_mask_uabi();
+		header.xfeatures &= fpstate->user_xfeatures & xfeatures;
 		break;
 	}
 
@@ -1033,17 +1203,15 @@
 
 	zerofrom = offsetof(struct xregs_state, extended_state_area);
 
-	for (i = FIRST_EXTENDED_XFEATURE; i < XFEATURE_MAX; i++) {
-		/*
-		 * The ptrace buffer is in non-compacted XSAVE format.
-		 * In non-compacted format disabled features still occupy
-		 * state space, but there is no state to copy from in the
-		 * compacted init_fpstate. The gap tracking will zero this
-		 * later.
-		 */
-		if (!(xfeatures_mask_uabi() & BIT_ULL(i)))
-			continue;
+	/*
+	 * The ptrace buffer is in non-compacted XSAVE format.  In
+	 * non-compacted format disabled features still occupy state space,
+	 * but there is no state to copy from in the compacted
+	 * init_fpstate. The gap tracking will zero these states.
+	 */
+	mask = fpstate->user_xfeatures;
 
+	for_each_extended_xfeature(i, mask) {
 		/*
 		 * If there was a feature or alignment gap, zero the space
 		 * in the destination buffer.
@@ -1055,10 +1223,9 @@
 			struct pkru_state pkru = {0};
 			/*
 			 * PKRU is not necessarily up to date in the
-			 * thread's XSAVE buffer.  Fill this part from the
-			 * per-thread storage.
+			 * XSAVE buffer. Use the provided value.
 			 */
-			pkru.pkru = tsk->thread.pkru;
+			pkru.pkru = pkru_val;
 			membuf_write(&to, &pkru, sizeof(pkru));
 		} else {
 			copy_feature(header.xfeatures & BIT_ULL(i), &to,
@@ -1078,6 +1245,26 @@
 		membuf_zero(&to, to.left);
 }
 
+/**
+ * copy_xstate_to_uabi_buf - Copy kernel saved xstate to a UABI buffer
+ * @to:		membuf descriptor
+ * @tsk:	The task from which to copy the saved xstate
+ * @copy_mode:	The requested copy mode
+ *
+ * Converts from kernel XSAVE or XSAVES compacted format to UABI conforming
+ * format, i.e. from the kernel internal hardware dependent storage format
+ * to the requested @mode. UABI XSTATE is always uncompacted!
+ *
+ * It supports partial copy but @to.pos always starts from zero.
+ */
+void copy_xstate_to_uabi_buf(struct membuf to, struct task_struct *tsk,
+			     enum xstate_copy_mode copy_mode)
+{
+	__copy_xstate_to_uabi_buf(to, tsk->thread.fpu.fpstate,
+				  tsk->thread.fpu.fpstate->user_xfeatures,
+				  tsk->thread.pkru, copy_mode);
+}
+
 static int copy_from_buffer(void *dst, unsigned int offset, unsigned int size,
 			    const void *kbuf, const void __user *ubuf)
 {
@@ -1091,9 +1278,10 @@
 }
 
 
-static int copy_uabi_to_xstate(struct xregs_state *xsave, const void *kbuf,
+static int copy_uabi_to_xstate(struct fpstate *fpstate, const void *kbuf,
 			       const void __user *ubuf)
 {
+	struct xregs_state *xsave = &fpstate->regs.xsave;
 	unsigned int offset, size;
 	struct xstate_header hdr;
 	u64 mask;
@@ -1103,7 +1291,7 @@
 	if (copy_from_buffer(&hdr, offset, sizeof(hdr), kbuf, ubuf))
 		return -EFAULT;
 
-	if (validate_user_xstate_header(&hdr))
+	if (validate_user_xstate_header(&hdr, fpstate))
 		return -EINVAL;
 
 	/* Validate MXCSR when any of the related features is in use */
@@ -1156,12 +1344,11 @@
 
 /*
  * Convert from a ptrace standard-format kernel buffer to kernel XSAVE[S]
- * format and copy to the target thread. This is called from
- * xstateregs_set().
+ * format and copy to the target thread. Used by ptrace and KVM.
  */
-int copy_uabi_from_kernel_to_xstate(struct xregs_state *xsave, const void *kbuf)
+int copy_uabi_from_kernel_to_xstate(struct fpstate *fpstate, const void *kbuf)
 {
-	return copy_uabi_to_xstate(xsave, kbuf, NULL);
+	return copy_uabi_to_xstate(fpstate, kbuf, NULL);
 }
 
 /*
@@ -1169,26 +1356,20 @@
  * XSAVE[S] format and copy to the target thread. This is called from the
  * sigreturn() and rt_sigreturn() system calls.
  */
-int copy_sigframe_from_user_to_xstate(struct xregs_state *xsave,
+int copy_sigframe_from_user_to_xstate(struct fpstate *fpstate,
 				      const void __user *ubuf)
 {
-	return copy_uabi_to_xstate(xsave, NULL, ubuf);
+	return copy_uabi_to_xstate(fpstate, NULL, ubuf);
 }
 
-static bool validate_xsaves_xrstors(u64 mask)
+static bool validate_independent_components(u64 mask)
 {
 	u64 xchk;
 
 	if (WARN_ON_FPU(!cpu_feature_enabled(X86_FEATURE_XSAVES)))
 		return false;
-	/*
-	 * Validate that this is either a task->fpstate related component
-	 * subset or an independent one.
-	 */
-	if (mask & xfeatures_mask_independent())
-		xchk = ~xfeatures_mask_independent();
-	else
-		xchk = ~xfeatures_mask_all;
+
+	xchk = ~xfeatures_mask_independent();
 
 	if (WARN_ON_ONCE(!mask || mask & xchk))
 		return false;
@@ -1206,14 +1387,13 @@
  * buffer should be zeroed otherwise a consecutive XRSTORS from that buffer
  * can #GP.
  *
- * The feature mask must either be a subset of the independent features or
- * a subset of the task->fpstate related features.
+ * The feature mask must be a subset of the independent features.
  */
 void xsaves(struct xregs_state *xstate, u64 mask)
 {
 	int err;
 
-	if (!validate_xsaves_xrstors(mask))
+	if (!validate_independent_components(mask))
 		return;
 
 	XSTATE_OP(XSAVES, xstate, (u32)mask, (u32)(mask >> 32), err);
@@ -1231,20 +1411,379 @@
  * Proper usage is to restore the state which was saved with
  * xsaves() into @xstate.
  *
- * The feature mask must either be a subset of the independent features or
- * a subset of the task->fpstate related features.
+ * The feature mask must be a subset of the independent features.
  */
 void xrstors(struct xregs_state *xstate, u64 mask)
 {
 	int err;
 
-	if (!validate_xsaves_xrstors(mask))
+	if (!validate_independent_components(mask))
 		return;
 
 	XSTATE_OP(XRSTORS, xstate, (u32)mask, (u32)(mask >> 32), err);
 	WARN_ON_ONCE(err);
 }
 
+#if IS_ENABLED(CONFIG_KVM)
+void fpstate_clear_xstate_component(struct fpstate *fps, unsigned int xfeature)
+{
+	void *addr = get_xsave_addr(&fps->regs.xsave, xfeature);
+
+	if (addr)
+		memset(addr, 0, xstate_sizes[xfeature]);
+}
+EXPORT_SYMBOL_GPL(fpstate_clear_xstate_component);
+#endif
+
+#ifdef CONFIG_X86_64
+
+#ifdef CONFIG_X86_DEBUG_FPU
+/*
+ * Ensure that a subsequent XSAVE* or XRSTOR* instruction with RFBM=@mask
+ * can safely operate on the @fpstate buffer.
+ */
+static bool xstate_op_valid(struct fpstate *fpstate, u64 mask, bool rstor)
+{
+	u64 xfd = __this_cpu_read(xfd_state);
+
+	if (fpstate->xfd == xfd)
+		return true;
+
+	 /*
+	  * The XFD MSR does not match fpstate->xfd. That's invalid when
+	  * the passed in fpstate is current's fpstate.
+	  */
+	if (fpstate->xfd == current->thread.fpu.fpstate->xfd)
+		return false;
+
+	/*
+	 * XRSTOR(S) from init_fpstate are always correct as it will just
+	 * bring all components into init state and not read from the
+	 * buffer. XSAVE(S) raises #PF after init.
+	 */
+	if (fpstate == &init_fpstate)
+		return rstor;
+
+	/*
+	 * XSAVE(S): clone(), fpu_swap_kvm_fpu()
+	 * XRSTORS(S): fpu_swap_kvm_fpu()
+	 */
+
+	/*
+	 * No XSAVE/XRSTOR instructions (except XSAVE itself) touch
+	 * the buffer area for XFD-disabled state components.
+	 */
+	mask &= ~xfd;
+
+	/*
+	 * Remove features which are valid in fpstate. They
+	 * have space allocated in fpstate.
+	 */
+	mask &= ~fpstate->xfeatures;
+
+	/*
+	 * Any remaining state components in 'mask' might be written
+	 * by XSAVE/XRSTOR. Fail validation it found.
+	 */
+	return !mask;
+}
+
+void xfd_validate_state(struct fpstate *fpstate, u64 mask, bool rstor)
+{
+	WARN_ON_ONCE(!xstate_op_valid(fpstate, mask, rstor));
+}
+#endif /* CONFIG_X86_DEBUG_FPU */
+
+static int __init xfd_update_static_branch(void)
+{
+	/*
+	 * If init_fpstate.xfd has bits set then dynamic features are
+	 * available and the dynamic sizing must be enabled.
+	 */
+	if (init_fpstate.xfd)
+		static_branch_enable(&__fpu_state_size_dynamic);
+	return 0;
+}
+arch_initcall(xfd_update_static_branch)
+
+void fpstate_free(struct fpu *fpu)
+{
+	if (fpu->fpstate && fpu->fpstate != &fpu->__fpstate)
+		vfree(fpu->fpstate);
+}
+
+/**
+ * fpu_install_fpstate - Update the active fpstate in the FPU
+ *
+ * @fpu:	A struct fpu * pointer
+ * @newfps:	A struct fpstate * pointer
+ *
+ * Returns:	A null pointer if the last active fpstate is the embedded
+ *		one or the new fpstate is already installed;
+ *		otherwise, a pointer to the old fpstate which has to
+ *		be freed by the caller.
+ */
+static struct fpstate *fpu_install_fpstate(struct fpu *fpu,
+					   struct fpstate *newfps)
+{
+	struct fpstate *oldfps = fpu->fpstate;
+
+	if (fpu->fpstate == newfps)
+		return NULL;
+
+	fpu->fpstate = newfps;
+	return oldfps != &fpu->__fpstate ? oldfps : NULL;
+}
+
+/**
+ * fpstate_realloc - Reallocate struct fpstate for the requested new features
+ *
+ * @xfeatures:	A bitmap of xstate features which extend the enabled features
+ *		of that task
+ * @ksize:	The required size for the kernel buffer
+ * @usize:	The required size for user space buffers
+ *
+ * Note vs. vmalloc(): If the task with a vzalloc()-allocated buffer
+ * terminates quickly, vfree()-induced IPIs may be a concern, but tasks
+ * with large states are likely to live longer.
+ *
+ * Returns: 0 on success, -ENOMEM on allocation error.
+ */
+static int fpstate_realloc(u64 xfeatures, unsigned int ksize,
+			   unsigned int usize)
+{
+	struct fpu *fpu = &current->thread.fpu;
+	struct fpstate *curfps, *newfps = NULL;
+	unsigned int fpsize;
+
+	curfps = fpu->fpstate;
+	fpsize = ksize + ALIGN(offsetof(struct fpstate, regs), 64);
+
+	newfps = vzalloc(fpsize);
+	if (!newfps)
+		return -ENOMEM;
+	newfps->size = ksize;
+	newfps->user_size = usize;
+	newfps->is_valloc = true;
+
+	fpregs_lock();
+	/*
+	 * Ensure that the current state is in the registers before
+	 * swapping fpstate as that might invalidate it due to layout
+	 * changes.
+	 */
+	if (test_thread_flag(TIF_NEED_FPU_LOAD))
+		fpregs_restore_userregs();
+
+	newfps->xfeatures = curfps->xfeatures | xfeatures;
+	newfps->user_xfeatures = curfps->user_xfeatures | xfeatures;
+	newfps->xfd = curfps->xfd & ~xfeatures;
+
+	curfps = fpu_install_fpstate(fpu, newfps);
+
+	/* Do the final updates within the locked region */
+	xstate_init_xcomp_bv(&newfps->regs.xsave, newfps->xfeatures);
+	xfd_update_state(newfps);
+
+	fpregs_unlock();
+
+	vfree(curfps);
+	return 0;
+}
+
+static int validate_sigaltstack(unsigned int usize)
+{
+	struct task_struct *thread, *leader = current->group_leader;
+	unsigned long framesize = get_sigframe_size();
+
+	lockdep_assert_held(&current->sighand->siglock);
+
+	/* get_sigframe_size() is based on fpu_user_cfg.max_size */
+	framesize -= fpu_user_cfg.max_size;
+	framesize += usize;
+	for_each_thread(leader, thread) {
+		if (thread->sas_ss_size && thread->sas_ss_size < framesize)
+			return -ENOSPC;
+	}
+	return 0;
+}
+
+static int __xstate_request_perm(u64 permitted, u64 requested)
+{
+	/*
+	 * This deliberately does not exclude !XSAVES as we still might
+	 * decide to optionally context switch XCR0 or talk the silicon
+	 * vendors into extending XFD for the pre AMX states, especially
+	 * AVX512.
+	 */
+	bool compacted = cpu_feature_enabled(X86_FEATURE_XSAVES);
+	struct fpu *fpu = &current->group_leader->thread.fpu;
+	unsigned int ksize, usize;
+	u64 mask;
+	int ret;
+
+	/* Check whether fully enabled */
+	if ((permitted & requested) == requested)
+		return 0;
+
+	/* Calculate the resulting kernel state size */
+	mask = permitted | requested;
+	ksize = xstate_calculate_size(mask, compacted);
+
+	/* Calculate the resulting user state size */
+	mask &= XFEATURE_MASK_USER_SUPPORTED;
+	usize = xstate_calculate_size(mask, false);
+
+	ret = validate_sigaltstack(usize);
+	if (ret)
+		return ret;
+
+	/* Pairs with the READ_ONCE() in xstate_get_group_perm() */
+	WRITE_ONCE(fpu->perm.__state_perm, mask);
+	/* Protected by sighand lock */
+	fpu->perm.__state_size = ksize;
+	fpu->perm.__user_state_size = usize;
+	return ret;
+}
+
+/*
+ * Permissions array to map facilities with more than one component
+ */
+static const u64 xstate_prctl_req[XFEATURE_MAX] = {
+	[XFEATURE_XTILE_DATA] = XFEATURE_MASK_XTILE_DATA,
+};
+
+static int xstate_request_perm(unsigned long idx)
+{
+	u64 permitted, requested;
+	int ret;
+
+	if (idx >= XFEATURE_MAX)
+		return -EINVAL;
+
+	/*
+	 * Look up the facility mask which can require more than
+	 * one xstate component.
+	 */
+	idx = array_index_nospec(idx, ARRAY_SIZE(xstate_prctl_req));
+	requested = xstate_prctl_req[idx];
+	if (!requested)
+		return -EOPNOTSUPP;
+
+	if ((fpu_user_cfg.max_features & requested) != requested)
+		return -EOPNOTSUPP;
+
+	/* Lockless quick check */
+	permitted = xstate_get_host_group_perm();
+	if ((permitted & requested) == requested)
+		return 0;
+
+	/* Protect against concurrent modifications */
+	spin_lock_irq(&current->sighand->siglock);
+	permitted = xstate_get_host_group_perm();
+	ret = __xstate_request_perm(permitted, requested);
+	spin_unlock_irq(&current->sighand->siglock);
+	return ret;
+}
+
+int xfd_enable_feature(u64 xfd_err)
+{
+	u64 xfd_event = xfd_err & XFEATURE_MASK_USER_DYNAMIC;
+	unsigned int ksize, usize;
+	struct fpu *fpu;
+
+	if (!xfd_event) {
+		pr_err_once("XFD: Invalid xfd error: %016llx\n", xfd_err);
+		return 0;
+	}
+
+	/* Protect against concurrent modifications */
+	spin_lock_irq(&current->sighand->siglock);
+
+	/* If not permitted let it die */
+	if ((xstate_get_host_group_perm() & xfd_event) != xfd_event) {
+		spin_unlock_irq(&current->sighand->siglock);
+		return -EPERM;
+	}
+
+	fpu = &current->group_leader->thread.fpu;
+	ksize = fpu->perm.__state_size;
+	usize = fpu->perm.__user_state_size;
+	/*
+	 * The feature is permitted. State size is sufficient.  Dropping
+	 * the lock is safe here even if more features are added from
+	 * another task, the retrieved buffer sizes are valid for the
+	 * currently requested feature(s).
+	 */
+	spin_unlock_irq(&current->sighand->siglock);
+
+	/*
+	 * Try to allocate a new fpstate. If that fails there is no way
+	 * out.
+	 */
+	if (fpstate_realloc(xfd_event, ksize, usize))
+		return -EFAULT;
+	return 0;
+}
+#else /* CONFIG_X86_64 */
+static inline int xstate_request_perm(unsigned long idx)
+{
+	return -EPERM;
+}
+#endif  /* !CONFIG_X86_64 */
+
+/**
+ * fpu_xstate_prctl - xstate permission operations
+ * @tsk:	Redundant pointer to current
+ * @option:	A subfunction of arch_prctl()
+ * @arg2:	option argument
+ * Return:	0 if successful; otherwise, an error code
+ *
+ * Option arguments:
+ *
+ * ARCH_GET_XCOMP_SUPP: Pointer to user space u64 to store the info
+ * ARCH_GET_XCOMP_PERM: Pointer to user space u64 to store the info
+ * ARCH_REQ_XCOMP_PERM: Facility number requested
+ *
+ * For facilities which require more than one XSTATE component, the request
+ * must be the highest state component number related to that facility,
+ * e.g. for AMX which requires XFEATURE_XTILE_CFG(17) and
+ * XFEATURE_XTILE_DATA(18) this would be XFEATURE_XTILE_DATA(18).
+ */
+long fpu_xstate_prctl(struct task_struct *tsk, int option, unsigned long arg2)
+{
+	u64 __user *uptr = (u64 __user *)arg2;
+	u64 permitted, supported;
+	unsigned long idx = arg2;
+
+	if (tsk != current)
+		return -EPERM;
+
+	switch (option) {
+	case ARCH_GET_XCOMP_SUPP:
+		supported = fpu_user_cfg.max_features |	fpu_user_cfg.legacy_features;
+		return put_user(supported, uptr);
+
+	case ARCH_GET_XCOMP_PERM:
+		/*
+		 * Lockless snapshot as it can also change right after the
+		 * dropping the lock.
+		 */
+		permitted = xstate_get_host_group_perm();
+		permitted &= XFEATURE_MASK_USER_SUPPORTED;
+		return put_user(permitted, uptr);
+
+	case ARCH_REQ_XCOMP_PERM:
+		if (!IS_ENABLED(CONFIG_X86_64))
+			return -EOPNOTSUPP;
+
+		return xstate_request_perm(idx);
+
+	default:
+		return -EINVAL;
+	}
+}
+
 #ifdef CONFIG_PROC_PID_ARCH_STATUS
 /*
  * Report the amount of time elapsed in millisecond since last AVX512
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/fpu/xstate.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/fpu/xstate.h
@@ -0,0 +1,279 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __X86_KERNEL_FPU_XSTATE_H
+#define __X86_KERNEL_FPU_XSTATE_H
+
+#include <asm/cpufeature.h>
+#include <asm/fpu/xstate.h>
+
+#ifdef CONFIG_X86_64
+DECLARE_PER_CPU(u64, xfd_state);
+#endif
+
+static inline void xstate_init_xcomp_bv(struct xregs_state *xsave, u64 mask)
+{
+	/*
+	 * XRSTORS requires these bits set in xcomp_bv, or it will
+	 * trigger #GP:
+	 */
+	if (cpu_feature_enabled(X86_FEATURE_XSAVES))
+		xsave->header.xcomp_bv = mask | XCOMP_BV_COMPACTED_FORMAT;
+}
+
+static inline u64 xstate_get_host_group_perm(void)
+{
+	/* Pairs with WRITE_ONCE() in xstate_request_perm() */
+	return READ_ONCE(current->group_leader->thread.fpu.perm.__state_perm);
+}
+
+enum xstate_copy_mode {
+	XSTATE_COPY_FP,
+	XSTATE_COPY_FX,
+	XSTATE_COPY_XSAVE,
+};
+
+struct membuf;
+extern void __copy_xstate_to_uabi_buf(struct membuf to, struct fpstate *fpstate,
+				      u64 xfeatures, u32 pkru_val,
+				      enum xstate_copy_mode copy_mode);
+extern void copy_xstate_to_uabi_buf(struct membuf to, struct task_struct *tsk,
+				    enum xstate_copy_mode mode);
+extern int copy_uabi_from_kernel_to_xstate(struct fpstate *fpstate, const void *kbuf);
+extern int copy_sigframe_from_user_to_xstate(struct fpstate *fpstate, const void __user *ubuf);
+
+
+extern void fpu__init_cpu_xstate(void);
+extern void fpu__init_system_xstate(unsigned int legacy_size);
+
+extern void *get_xsave_addr(struct xregs_state *xsave, int xfeature_nr);
+
+static inline u64 xfeatures_mask_supervisor(void)
+{
+	return fpu_kernel_cfg.max_features & XFEATURE_MASK_SUPERVISOR_SUPPORTED;
+}
+
+static inline u64 xfeatures_mask_independent(void)
+{
+	if (!cpu_feature_enabled(X86_FEATURE_ARCH_LBR))
+		return fpu_kernel_cfg.independent_features & ~XFEATURE_MASK_LBR;
+
+	return fpu_kernel_cfg.independent_features;
+}
+
+/* XSAVE/XRSTOR wrapper functions */
+
+#ifdef CONFIG_X86_64
+#define REX_PREFIX	"0x48, "
+#else
+#define REX_PREFIX
+#endif
+
+/* These macros all use (%edi)/(%rdi) as the single memory argument. */
+#define XSAVE		".byte " REX_PREFIX "0x0f,0xae,0x27"
+#define XSAVEOPT	".byte " REX_PREFIX "0x0f,0xae,0x37"
+#define XSAVES		".byte " REX_PREFIX "0x0f,0xc7,0x2f"
+#define XRSTOR		".byte " REX_PREFIX "0x0f,0xae,0x2f"
+#define XRSTORS		".byte " REX_PREFIX "0x0f,0xc7,0x1f"
+
+/*
+ * After this @err contains 0 on success or the trap number when the
+ * operation raises an exception.
+ */
+#define XSTATE_OP(op, st, lmask, hmask, err)				\
+	asm volatile("1:" op "\n\t"					\
+		     "xor %[err], %[err]\n"				\
+		     "2:\n\t"						\
+		     _ASM_EXTABLE_TYPE(1b, 2b, EX_TYPE_FAULT_MCE_SAFE)	\
+		     : [err] "=a" (err)					\
+		     : "D" (st), "m" (*st), "a" (lmask), "d" (hmask)	\
+		     : "memory")
+
+/*
+ * If XSAVES is enabled, it replaces XSAVEOPT because it supports a compact
+ * format and supervisor states in addition to modified optimization in
+ * XSAVEOPT.
+ *
+ * Otherwise, if XSAVEOPT is enabled, XSAVEOPT replaces XSAVE because XSAVEOPT
+ * supports modified optimization which is not supported by XSAVE.
+ *
+ * We use XSAVE as a fallback.
+ *
+ * The 661 label is defined in the ALTERNATIVE* macros as the address of the
+ * original instruction which gets replaced. We need to use it here as the
+ * address of the instruction where we might get an exception at.
+ */
+#define XSTATE_XSAVE(st, lmask, hmask, err)				\
+	asm volatile(ALTERNATIVE_2(XSAVE,				\
+				   XSAVEOPT, X86_FEATURE_XSAVEOPT,	\
+				   XSAVES,   X86_FEATURE_XSAVES)	\
+		     "\n"						\
+		     "xor %[err], %[err]\n"				\
+		     "3:\n"						\
+		     ".pushsection .fixup,\"ax\"\n"			\
+		     "4: movl $-2, %[err]\n"				\
+		     "jmp 3b\n"						\
+		     ".popsection\n"					\
+		     _ASM_EXTABLE(661b, 4b)				\
+		     : [err] "=r" (err)					\
+		     : "D" (st), "m" (*st), "a" (lmask), "d" (hmask)	\
+		     : "memory")
+
+/*
+ * Use XRSTORS to restore context if it is enabled. XRSTORS supports compact
+ * XSAVE area format.
+ */
+#define XSTATE_XRESTORE(st, lmask, hmask)				\
+	asm volatile(ALTERNATIVE(XRSTOR,				\
+				 XRSTORS, X86_FEATURE_XSAVES)		\
+		     "\n"						\
+		     "3:\n"						\
+		     _ASM_EXTABLE_TYPE(661b, 3b, EX_TYPE_FPU_RESTORE)	\
+		     :							\
+		     : "D" (st), "m" (*st), "a" (lmask), "d" (hmask)	\
+		     : "memory")
+
+#if defined(CONFIG_X86_64) && defined(CONFIG_X86_DEBUG_FPU)
+extern void xfd_validate_state(struct fpstate *fpstate, u64 mask, bool rstor);
+#else
+static inline void xfd_validate_state(struct fpstate *fpstate, u64 mask, bool rstor) { }
+#endif
+
+#ifdef CONFIG_X86_64
+static inline void xfd_update_state(struct fpstate *fpstate)
+{
+	if (fpu_state_size_dynamic()) {
+		u64 xfd = fpstate->xfd;
+
+		if (__this_cpu_read(xfd_state) != xfd) {
+			wrmsrl(MSR_IA32_XFD, xfd);
+			__this_cpu_write(xfd_state, xfd);
+		}
+	}
+}
+#else
+static inline void xfd_update_state(struct fpstate *fpstate) { }
+#endif
+
+/*
+ * Save processor xstate to xsave area.
+ *
+ * Uses either XSAVE or XSAVEOPT or XSAVES depending on the CPU features
+ * and command line options. The choice is permanent until the next reboot.
+ */
+static inline void os_xsave(struct fpstate *fpstate)
+{
+	u64 mask = fpstate->xfeatures;
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+	int err;
+
+	WARN_ON_FPU(!alternatives_patched);
+	xfd_validate_state(fpstate, mask, false);
+
+	XSTATE_XSAVE(&fpstate->regs.xsave, lmask, hmask, err);
+
+	/* We should never fault when copying to a kernel buffer: */
+	WARN_ON_FPU(err);
+}
+
+/*
+ * Restore processor xstate from xsave area.
+ *
+ * Uses XRSTORS when XSAVES is used, XRSTOR otherwise.
+ */
+static inline void os_xrstor(struct fpstate *fpstate, u64 mask)
+{
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+
+	xfd_validate_state(fpstate, mask, true);
+	XSTATE_XRESTORE(&fpstate->regs.xsave, lmask, hmask);
+}
+
+/* Restore of supervisor state. Does not require XFD */
+static inline void os_xrstor_supervisor(struct fpstate *fpstate)
+{
+	u64 mask = xfeatures_mask_supervisor();
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+
+	XSTATE_XRESTORE(&fpstate->regs.xsave, lmask, hmask);
+}
+
+/*
+ * Save xstate to user space xsave area.
+ *
+ * We don't use modified optimization because xrstor/xrstors might track
+ * a different application.
+ *
+ * We don't use compacted format xsave area for backward compatibility for
+ * old applications which don't understand the compacted format of the
+ * xsave area.
+ *
+ * The caller has to zero buf::header before calling this because XSAVE*
+ * does not touch the reserved fields in the header.
+ */
+static inline int xsave_to_user_sigframe(struct xregs_state __user *buf)
+{
+	/*
+	 * Include the features which are not xsaved/rstored by the kernel
+	 * internally, e.g. PKRU. That's user space ABI and also required
+	 * to allow the signal handler to modify PKRU.
+	 */
+	struct fpstate *fpstate = current->thread.fpu.fpstate;
+	u64 mask = fpstate->user_xfeatures;
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+	int err;
+
+	xfd_validate_state(fpstate, mask, false);
+
+	stac();
+	XSTATE_OP(XSAVE, buf, lmask, hmask, err);
+	clac();
+
+	return err;
+}
+
+/*
+ * Restore xstate from user space xsave area.
+ */
+static inline int xrstor_from_user_sigframe(struct xregs_state __user *buf, u64 mask)
+{
+	struct xregs_state *xstate = ((__force struct xregs_state *)buf);
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+	int err;
+
+	xfd_validate_state(current->thread.fpu.fpstate, mask, true);
+
+	stac();
+	XSTATE_OP(XRSTOR, xstate, lmask, hmask, err);
+	clac();
+
+	return err;
+}
+
+/*
+ * Restore xstate from kernel space xsave area, return an error code instead of
+ * an exception.
+ */
+static inline int os_xrstor_safe(struct fpstate *fpstate, u64 mask)
+{
+	struct xregs_state *xstate = &fpstate->regs.xsave;
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+	int err;
+
+	/* Ensure that XFD is up to date */
+	xfd_update_state(fpstate);
+
+	if (cpu_feature_enabled(X86_FEATURE_XSAVES))
+		XSTATE_OP(XRSTORS, xstate, lmask, hmask, err);
+	else
+		XSTATE_OP(XRSTOR, xstate, lmask, hmask, err);
+
+	return err;
+}
+
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/ftrace.c
@@ -93,6 +93,7 @@
 
 	/* Make sure it is what we expect it to be */
 	if (memcmp(cur_code, old_code, MCOUNT_INSN_SIZE) != 0) {
+		ftrace_expected = old_code;
 		WARN_ON(1);
 		return -EINVAL;
 	}
@@ -218,7 +219,9 @@
 
 		ret = ftrace_verify_code(rec->ip, old);
 		if (ret) {
+			ftrace_expected = old;
 			ftrace_bug(ret, rec);
+			ftrace_expected = NULL;
 			return;
 		}
 	}
@@ -308,7 +311,7 @@
 	} __attribute__((packed));
 };
 
-#define RET_SIZE		1
+#define RET_SIZE		(IS_ENABLED(CONFIG_RETPOLINE) ? 5 : 1 + IS_ENABLED(CONFIG_SLS))
 
 static unsigned long
 create_trampoline(struct ftrace_ops *ops, unsigned int *tramp_size)
@@ -321,12 +324,12 @@
 	unsigned long offset;
 	unsigned long npages;
 	unsigned long size;
-	unsigned long retq;
 	unsigned long *ptr;
 	void *trampoline;
 	void *ip;
 	/* 48 8b 15 <offset> is movq <offset>(%rip), %rdx */
 	unsigned const char op_ref[] = { 0x48, 0x8b, 0x15 };
+	unsigned const char retq[] = { RET_INSN_OPCODE, INT3_INSN_OPCODE };
 	union ftrace_op_code_union op_ptr;
 	int ret;
 
@@ -364,12 +367,10 @@
 		goto fail;
 
 	ip = trampoline + size;
-
-	/* The trampoline ends with ret(q) */
-	retq = (unsigned long)ftrace_stub;
-	ret = copy_from_kernel_nofault(ip, (void *)retq, RET_SIZE);
-	if (WARN_ON(ret < 0))
-		goto fail;
+	if (cpu_feature_enabled(X86_FEATURE_RETHUNK))
+		__text_gen_insn(ip, JMP32_INSN_OPCODE, ip, x86_return_thunk, JMP32_INSN_SIZE);
+	else
+		memcpy(ip, retq, sizeof(retq));
 
 	/* No need to test direct calls on created trampolines */
 	if (ops->flags & FTRACE_OPS_FL_SAVE_REGS) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/ftrace_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/ftrace_32.S
@@ -19,7 +19,7 @@
 #endif
 
 SYM_FUNC_START(__fentry__)
-	ret
+	RET
 SYM_FUNC_END(__fentry__)
 EXPORT_SYMBOL(__fentry__)
 
@@ -84,7 +84,7 @@
 
 /* This is weak to keep gas from relaxing the jumps */
 SYM_INNER_LABEL_ALIGN(ftrace_stub, SYM_L_WEAK)
-	ret
+	RET
 SYM_CODE_END(ftrace_caller)
 
 SYM_CODE_START(ftrace_regs_caller)
@@ -177,7 +177,7 @@
 	popl	%edx
 	popl	%ecx
 	popl	%eax
-	ret
+	RET
 SYM_CODE_END(ftrace_graph_caller)
 
 .globl return_to_handler
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/ftrace_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/ftrace_64.S
@@ -132,7 +132,7 @@
 #ifdef CONFIG_DYNAMIC_FTRACE
 
 SYM_FUNC_START(__fentry__)
-	retq
+	RET
 SYM_FUNC_END(__fentry__)
 EXPORT_SYMBOL(__fentry__)
 
@@ -181,11 +181,10 @@
 
 /*
  * This is weak to keep gas from relaxing the jumps.
- * It is also used to copy the retq for trampolines.
  */
 SYM_INNER_LABEL_ALIGN(ftrace_stub, SYM_L_WEAK)
 	UNWIND_HINT_FUNC
-	retq
+	RET
 SYM_FUNC_END(ftrace_epilogue)
 
 SYM_FUNC_START(ftrace_regs_caller)
@@ -299,7 +298,7 @@
 #endif
 
 SYM_INNER_LABEL(ftrace_stub, SYM_L_GLOBAL)
-	retq
+	RET
 
 trace:
 	/* save_mcount_regs fills in first two parameters */
@@ -331,11 +330,11 @@
 
 	restore_mcount_regs
 
-	retq
+	RET
 SYM_FUNC_END(ftrace_graph_caller)
 
 SYM_FUNC_START(return_to_handler)
-	subq  $24, %rsp
+	subq  $16, %rsp
 
 	/* Save the return values */
 	movq %rax, (%rsp)
@@ -347,7 +346,19 @@
 	movq %rax, %rdi
 	movq 8(%rsp), %rdx
 	movq (%rsp), %rax
-	addq $24, %rsp
-	JMP_NOSPEC rdi
+
+	addq $16, %rsp
+	/*
+	 * Jump back to the old return address. This cannot be JMP_NOSPEC rdi
+	 * since IBT would demand that contain ENDBR, which simply isn't so for
+	 * return addresses. Use a retpoline here to keep the RSB balanced.
+	 */
+	ANNOTATE_INTRA_FUNCTION_CALL
+	call .Ldo_rop
+	int3
+.Ldo_rop:
+	mov %rdi, (%rsp)
+	UNWIND_HINT_FUNC
+	RET
 SYM_FUNC_END(return_to_handler)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/head64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/head64.c
@@ -79,7 +79,7 @@
  * while the kernel still uses a direct mapping.
  */
 static struct desc_ptr startup_gdt_descr = {
-	.size = sizeof(startup_gdt),
+	.size = sizeof(startup_gdt)-1,
 	.address = 0,
 };
 
@@ -418,6 +418,8 @@
 {
 	memset(__bss_start, 0,
 	       (unsigned long) __bss_stop - (unsigned long) __bss_start);
+	memset(__brk_base, 0,
+	       (unsigned long) __brk_limit - (unsigned long) __brk_base);
 }
 
 static unsigned long get_cmd_line_ptr(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/head_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/head_32.S
@@ -23,9 +23,11 @@
 #include <asm/cpufeatures.h>
 #include <asm/percpu.h>
 #include <asm/nops.h>
+#include <asm/nospec-branch.h>
 #include <asm/bootparam.h>
 #include <asm/export.h>
 #include <asm/pgtable_32.h>
+#include <asm/nospec-branch.h>
 
 /* Physical address */
 #define pa(X) ((X) - __PAGE_OFFSET)
@@ -266,6 +268,7 @@
 	movl setup_once_ref,%eax
 	andl %eax,%eax
 	jz 1f				# Did we do this already?
+	ANNOTATE_RETPOLINE_SAFE
 	call *%eax
 1:
 
@@ -340,7 +343,7 @@
 __INIT
 setup_once:
 	andl $0,setup_once_ref	/* Once is enough, thanks */
-	ret
+	RET
 
 SYM_FUNC_START(early_idt_handler_array)
 	# 36(%esp) %eflags
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/head_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/head_64.S
@@ -312,6 +312,8 @@
 SYM_CODE_START_NOALIGN(vc_boot_ghcb)
 	UNWIND_HINT_IRET_REGS offset=8
 
+	ANNOTATE_UNRET_END
+
 	/* Build pt_regs */
 	PUSH_AND_CLEAR_REGS
 
@@ -369,6 +371,7 @@
 SYM_CODE_END(early_idt_handler_array)
 
 SYM_CODE_START_LOCAL(early_idt_handler_common)
+	ANNOTATE_UNRET_END
 	/*
 	 * The stack is the hardware frame, an error code or zero, and the
 	 * vector number.
@@ -415,6 +418,8 @@
 SYM_CODE_START_NOALIGN(vc_no_ghcb)
 	UNWIND_HINT_IRET_REGS offset=8
 
+	ANNOTATE_UNRET_END
+
 	/* Build pt_regs */
 	PUSH_AND_CLEAR_REGS
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/hpet.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/hpet.c
@@ -1435,8 +1435,12 @@
 	hpet_rtc_timer_reinit();
 	memset(&curr_time, 0, sizeof(struct rtc_time));
 
-	if (hpet_rtc_flags & (RTC_UIE | RTC_AIE))
-		mc146818_get_time(&curr_time);
+	if (hpet_rtc_flags & (RTC_UIE | RTC_AIE)) {
+		if (unlikely(mc146818_get_time(&curr_time) < 0)) {
+			pr_err_ratelimited("unable to read current time from RTC\n");
+			return IRQ_HANDLED;
+		}
+	}
 
 	if (hpet_rtc_flags & RTC_UIE &&
 	    curr_time.tm_sec != hpet_prev_update_sec) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/hw_breakpoint.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/hw_breakpoint.c
@@ -266,7 +266,7 @@
 
 	/* CPU entry erea is always used for CPU entry */
 	if (within_area(addr, end, CPU_ENTRY_AREA_BASE,
-			CPU_ENTRY_AREA_TOTAL_SIZE))
+			CPU_ENTRY_AREA_MAP_SIZE))
 		return true;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/i8253.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/i8253.c
@@ -8,6 +8,7 @@
 #include <linux/timex.h>
 #include <linux/i8253.h>
 
+#include <asm/hypervisor.h>
 #include <asm/apic.h>
 #include <asm/hpet.h>
 #include <asm/time.h>
@@ -39,9 +40,15 @@
 
 bool __init pit_timer_init(void)
 {
-	if (!use_pit())
+	if (!use_pit()) {
+		/*
+		 * Don't just ignore the PIT. Ensure it's stopped, because
+		 * VMMs otherwise steal CPU time just to pointlessly waggle
+		 * the (masked) IRQ.
+		 */
+		clockevent_i8253_disable();
 		return false;
-
+	}
 	clockevent_i8253_init(true);
 	global_clock_event = &i8253_clockevent;
 	return true;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/i8259.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/i8259.c
@@ -32,6 +32,7 @@
  */
 static void init_8259A(int auto_eoi);
 
+static bool pcat_compat __ro_after_init;
 static int i8259A_auto_eoi;
 DEFINE_RAW_SPINLOCK(i8259A_lock);
 
@@ -114,6 +115,7 @@
 	disable_irq_nosync(irq);
 	io_apic_irqs &= ~(1<<irq);
 	irq_set_chip_and_handler(irq, &i8259A_chip, handle_level_irq);
+	irq_set_status_flags(irq, IRQ_LEVEL);
 	enable_irq(irq);
 	lapic_assign_legacy_vector(irq, true);
 }
@@ -300,15 +302,32 @@
 
 static int probe_8259A(void)
 {
+	unsigned char new_val, probe_val = ~(1 << PIC_CASCADE_IR);
 	unsigned long flags;
-	unsigned char probe_val = ~(1 << PIC_CASCADE_IR);
-	unsigned char new_val;
+
+	/*
+	 * If MADT has the PCAT_COMPAT flag set, then do not bother probing
+	 * for the PIC. Some BIOSes leave the PIC uninitialized and probing
+	 * fails.
+	 *
+	 * Right now this causes problems as quite some code depends on
+	 * nr_legacy_irqs() > 0 or has_legacy_pic() == true. This is silly
+	 * when the system has an IO/APIC because then PIC is not required
+	 * at all, except for really old machines where the timer interrupt
+	 * must be routed through the PIC. So just pretend that the PIC is
+	 * there and let legacy_pic->init() initialize it for nothing.
+	 *
+	 * Alternatively this could just try to initialize the PIC and
+	 * repeat the probe, but for cases where there is no PIC that's
+	 * just pointless.
+	 */
+	if (pcat_compat)
+		return nr_legacy_irqs();
+
 	/*
-	 * Check to see if we have a PIC.
-	 * Mask all except the cascade and read
-	 * back the value we just wrote. If we don't
-	 * have a PIC, we will read 0xff as opposed to the
-	 * value we wrote.
+	 * Check to see if we have a PIC.  Mask all except the cascade and
+	 * read back the value we just wrote. If we don't have a PIC, we
+	 * will read 0xff as opposed to the value we wrote.
 	 */
 	raw_spin_lock_irqsave(&i8259A_lock, flags);
 
@@ -430,5 +449,9 @@
 
 	return 0;
 }
-
 device_initcall(i8259A_init_ops);
+
+void __init legacy_pic_pcat_compat(void)
+{
+	pcat_compat = true;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/idt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/idt.c
@@ -109,7 +109,7 @@
 
 	SYSG(X86_TRAP_OF,		asm_exc_overflow),
 #if defined(CONFIG_IA32_EMULATION)
-	SYSG(IA32_SYSCALL_VECTOR,	entry_INT80_compat),
+	SYSG(IA32_SYSCALL_VECTOR,	asm_int80_emulation),
 #elif defined(CONFIG_X86_32)
 	SYSG(IA32_SYSCALL_VECTOR,	entry_INT80_32),
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/irq.c
@@ -23,8 +23,10 @@
 #include <asm/traps.h>
 #include <asm/thermal.h>
 
+#if defined(CONFIG_X86_LOCAL_APIC) || defined(CONFIG_X86_THERMAL_VECTOR)
 #define CREATE_TRACE_POINTS
 #include <asm/trace/irq_vectors.h>
+#endif
 
 DEFINE_PER_CPU_SHARED_ALIGNED(irq_cpustat_t, irq_stat);
 EXPORT_PER_CPU_SYMBOL(irq_stat);
@@ -291,8 +293,10 @@
 {
 	if (handler)
 		kvm_posted_intr_wakeup_handler = handler;
-	else
+	else {
 		kvm_posted_intr_wakeup_handler = dummy_handler;
+		synchronize_rcu();
+	}
 }
 EXPORT_SYMBOL_GPL(kvm_set_posted_intr_wakeup_handler);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/irqflags.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/irqflags.S
@@ -10,6 +10,6 @@
 SYM_FUNC_START(native_save_fl)
 	pushf
 	pop %_ASM_AX
-	ret
+	RET
 SYM_FUNC_END(native_save_fl)
 EXPORT_SYMBOL(native_save_fl)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/irqinit.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/irqinit.c
@@ -65,8 +65,10 @@
 
 	legacy_pic->init(0);
 
-	for (i = 0; i < nr_legacy_irqs(); i++)
+	for (i = 0; i < nr_legacy_irqs(); i++) {
 		irq_set_chip_and_handler(i, chip, handle_level_irq);
+		irq_set_status_flags(i, IRQ_LEVEL);
+	}
 }
 
 void __init init_IRQ(void)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/itmt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/itmt.c
@@ -198,7 +198,7 @@
 		 * of the priority chain and only used when
 		 * all other high priority cpus are out of capacity.
 		 */
-		smt_prio = prio * smp_num_siblings / i;
+		smt_prio = prio * smp_num_siblings / (i * i);
 		per_cpu(sched_core_priority, cpu) = smt_prio;
 		i++;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/kdebugfs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/kdebugfs.c
@@ -88,11 +88,13 @@
 
 static int __init create_setup_data_nodes(struct dentry *parent)
 {
+	struct setup_indirect *indirect;
 	struct setup_data_node *node;
 	struct setup_data *data;
-	int error;
+	u64 pa_data, pa_next;
 	struct dentry *d;
-	u64 pa_data;
+	int error;
+	u32 len;
 	int no = 0;
 
 	d = debugfs_create_dir("setup_data", parent);
@@ -112,12 +114,29 @@
 			error = -ENOMEM;
 			goto err_dir;
 		}
+		pa_next = data->next;
 
-		if (data->type == SETUP_INDIRECT &&
-		    ((struct setup_indirect *)data->data)->type != SETUP_INDIRECT) {
-			node->paddr = ((struct setup_indirect *)data->data)->addr;
-			node->type  = ((struct setup_indirect *)data->data)->type;
-			node->len   = ((struct setup_indirect *)data->data)->len;
+		if (data->type == SETUP_INDIRECT) {
+			len = sizeof(*data) + data->len;
+			memunmap(data);
+			data = memremap(pa_data, len, MEMREMAP_WB);
+			if (!data) {
+				kfree(node);
+				error = -ENOMEM;
+				goto err_dir;
+			}
+
+			indirect = (struct setup_indirect *)data->data;
+
+			if (indirect->type != SETUP_INDIRECT) {
+				node->paddr = indirect->addr;
+				node->type  = indirect->type;
+				node->len   = indirect->len;
+			} else {
+				node->paddr = pa_data;
+				node->type  = data->type;
+				node->len   = data->len;
+			}
 		} else {
 			node->paddr = pa_data;
 			node->type  = data->type;
@@ -125,7 +144,7 @@
 		}
 
 		create_setup_data_node(d, no, node);
-		pa_data = data->next;
+		pa_data = pa_next;
 
 		memunmap(data);
 		no++;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/kexec-bzimage64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/kexec-bzimage64.c
@@ -17,7 +17,6 @@
 #include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/efi.h>
-#include <linux/verification.h>
 
 #include <asm/bootparam.h>
 #include <asm/setup.h>
@@ -528,28 +527,11 @@
 	return 0;
 }
 
-#ifdef CONFIG_KEXEC_BZIMAGE_VERIFY_SIG
-static int bzImage64_verify_sig(const char *kernel, unsigned long kernel_len)
-{
-	int ret;
-
-	ret = verify_pefile_signature(kernel, kernel_len,
-				      VERIFY_USE_SECONDARY_KEYRING,
-				      VERIFYING_KEXEC_PE_SIGNATURE);
-	if (ret == -ENOKEY && IS_ENABLED(CONFIG_INTEGRITY_PLATFORM_KEYRING)) {
-		ret = verify_pefile_signature(kernel, kernel_len,
-					      VERIFY_USE_PLATFORM_KEYRING,
-					      VERIFYING_KEXEC_PE_SIGNATURE);
-	}
-	return ret;
-}
-#endif
-
 const struct kexec_file_ops kexec_bzImage64_ops = {
 	.probe = bzImage64_probe,
 	.load = bzImage64_load,
 	.cleanup = bzImage64_cleanup,
 #ifdef CONFIG_KEXEC_BZIMAGE_VERIFY_SIG
-	.verify_sig = bzImage64_verify_sig,
+	.verify_sig = kexec_kernel_verify_pe_sig,
 #endif
 };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/kprobes/core.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/kprobes/core.c
@@ -37,6 +37,7 @@
 #include <linux/extable.h>
 #include <linux/kdebug.h>
 #include <linux/kallsyms.h>
+#include <linux/kgdb.h>
 #include <linux/ftrace.h>
 #include <linux/kasan.h>
 #include <linux/moduleloader.h>
@@ -193,17 +194,10 @@
 __recover_probed_insn(kprobe_opcode_t *buf, unsigned long addr)
 {
 	struct kprobe *kp;
-	unsigned long faddr;
+	bool faddr;
 
 	kp = get_kprobe((void *)addr);
-	faddr = ftrace_location(addr);
-	/*
-	 * Addresses inside the ftrace location are refused by
-	 * arch_check_ftrace_location(). Something went terribly wrong
-	 * if such an address is checked here.
-	 */
-	if (WARN_ON(faddr && faddr != addr))
-		return 0UL;
+	faddr = ftrace_location(addr) == addr;
 	/*
 	 * Use the current code if it is not modified by Kprobe
 	 * and it cannot be modified by ftrace.
@@ -289,12 +283,15 @@
 		if (ret < 0)
 			return 0;
 
+#ifdef CONFIG_KGDB
 		/*
-		 * Another debugging subsystem might insert this breakpoint.
-		 * In that case, we can't recover it.
+		 * If there is a dynamically installed kgdb sw breakpoint,
+		 * this function should not be probed.
 		 */
-		if (insn.opcode.bytes[0] == INT3_INSN_OPCODE)
+		if (insn.opcode.bytes[0] == INT3_INSN_OPCODE &&
+		    kgdb_has_hit_break(addr))
 			return 0;
+#endif
 		addr += insn.length;
 	}
 
@@ -459,50 +456,26 @@
 }
 NOKPROBE_SYMBOL(kprobe_emulate_call);
 
-static nokprobe_inline
-void __kprobe_emulate_jmp(struct kprobe *p, struct pt_regs *regs, bool cond)
+static void kprobe_emulate_jmp(struct kprobe *p, struct pt_regs *regs)
 {
 	unsigned long ip = regs->ip - INT3_INSN_SIZE + p->ainsn.size;
 
-	if (cond)
-		ip += p->ainsn.rel32;
+	ip += p->ainsn.rel32;
 	int3_emulate_jmp(regs, ip);
 }
-
-static void kprobe_emulate_jmp(struct kprobe *p, struct pt_regs *regs)
-{
-	__kprobe_emulate_jmp(p, regs, true);
-}
 NOKPROBE_SYMBOL(kprobe_emulate_jmp);
 
-static const unsigned long jcc_mask[6] = {
-	[0] = X86_EFLAGS_OF,
-	[1] = X86_EFLAGS_CF,
-	[2] = X86_EFLAGS_ZF,
-	[3] = X86_EFLAGS_CF | X86_EFLAGS_ZF,
-	[4] = X86_EFLAGS_SF,
-	[5] = X86_EFLAGS_PF,
-};
-
 static void kprobe_emulate_jcc(struct kprobe *p, struct pt_regs *regs)
 {
-	bool invert = p->ainsn.jcc.type & 1;
-	bool match;
+	unsigned long ip = regs->ip - INT3_INSN_SIZE + p->ainsn.size;
 
-	if (p->ainsn.jcc.type < 0xc) {
-		match = regs->flags & jcc_mask[p->ainsn.jcc.type >> 1];
-	} else {
-		match = ((regs->flags & X86_EFLAGS_SF) >> X86_EFLAGS_SF_BIT) ^
-			((regs->flags & X86_EFLAGS_OF) >> X86_EFLAGS_OF_BIT);
-		if (p->ainsn.jcc.type >= 0xe)
-			match = match && (regs->flags & X86_EFLAGS_ZF);
-	}
-	__kprobe_emulate_jmp(p, regs, (match && !invert) || (!match && invert));
+	int3_emulate_jcc(regs, p->ainsn.jcc.type, ip, p->ainsn.rel32);
 }
 NOKPROBE_SYMBOL(kprobe_emulate_jcc);
 
 static void kprobe_emulate_loop(struct kprobe *p, struct pt_regs *regs)
 {
+	unsigned long ip = regs->ip - INT3_INSN_SIZE + p->ainsn.size;
 	bool match;
 
 	if (p->ainsn.loop.type != 3) {	/* LOOP* */
@@ -530,7 +503,9 @@
 	else if (p->ainsn.loop.type == 1)	/* LOOPE */
 		match = match && (regs->flags & X86_EFLAGS_ZF);
 
-	__kprobe_emulate_jmp(p, regs, match);
+	if (match)
+		ip += p->ainsn.rel32;
+	int3_emulate_jmp(regs, ip);
 }
 NOKPROBE_SYMBOL(kprobe_emulate_loop);
 
@@ -559,7 +534,8 @@
 {
 	unsigned long offs = addrmode_regoffs[p->ainsn.indirect.reg];
 
-	int3_emulate_call(regs, regs_get_register(regs, offs));
+	int3_emulate_push(regs, regs->ip - INT3_INSN_SIZE + p->ainsn.size);
+	int3_emulate_jmp(regs, regs_get_register(regs, offs));
 }
 NOKPROBE_SYMBOL(kprobe_emulate_call_indirect);
 
@@ -809,23 +785,27 @@
 	ri->fp = sara;
 
 	/* Replace the return addr with trampoline addr */
-	*sara = (unsigned long) &kretprobe_trampoline;
+	*sara = (unsigned long) &__kretprobe_trampoline;
 }
 NOKPROBE_SYMBOL(arch_prepare_kretprobe);
 
 static void kprobe_post_process(struct kprobe *cur, struct pt_regs *regs,
 			       struct kprobe_ctlblk *kcb)
 {
-	if ((kcb->kprobe_status != KPROBE_REENTER) && cur->post_handler) {
-		kcb->kprobe_status = KPROBE_HIT_SSDONE;
-		cur->post_handler(cur, regs, 0);
-	}
-
 	/* Restore back the original saved kprobes variables and continue. */
-	if (kcb->kprobe_status == KPROBE_REENTER)
+	if (kcb->kprobe_status == KPROBE_REENTER) {
+		/* This will restore both kcb and current_kprobe */
 		restore_previous_kprobe(kcb);
-	else
+	} else {
+		/*
+		 * Always update the kcb status because
+		 * reset_curent_kprobe() doesn't update kcb.
+		 */
+		kcb->kprobe_status = KPROBE_HIT_SSDONE;
+		if (cur->post_handler)
+			cur->post_handler(cur, regs, 0);
 		reset_current_kprobe();
+	}
 }
 NOKPROBE_SYMBOL(kprobe_post_process);
 
@@ -1019,9 +999,9 @@
  */
 asm(
 	".text\n"
-	".global kretprobe_trampoline\n"
-	".type kretprobe_trampoline, @function\n"
-	"kretprobe_trampoline:\n"
+	".global __kretprobe_trampoline\n"
+	".type __kretprobe_trampoline, @function\n"
+	"__kretprobe_trampoline:\n"
 	/* We don't bother saving the ss register */
 #ifdef CONFIG_X86_64
 	"	pushq %rsp\n"
@@ -1044,15 +1024,15 @@
 	RESTORE_REGS_STRING
 	"	popfl\n"
 #endif
-	"	ret\n"
-	".size kretprobe_trampoline, .-kretprobe_trampoline\n"
+	ASM_RET
+	".size __kretprobe_trampoline, .-__kretprobe_trampoline\n"
 );
-NOKPROBE_SYMBOL(kretprobe_trampoline);
-STACK_FRAME_NON_STANDARD(kretprobe_trampoline);
+NOKPROBE_SYMBOL(__kretprobe_trampoline);
+STACK_FRAME_NON_STANDARD(__kretprobe_trampoline);
 
 
 /*
- * Called from kretprobe_trampoline
+ * Called from __kretprobe_trampoline
  */
 __used __visible void *trampoline_handler(struct pt_regs *regs)
 {
@@ -1061,10 +1041,10 @@
 #ifdef CONFIG_X86_32
 	regs->gs = 0;
 #endif
-	regs->ip = (unsigned long)&kretprobe_trampoline;
+	regs->ip = (unsigned long)&__kretprobe_trampoline;
 	regs->orig_ax = ~0UL;
 
-	return (void *)kretprobe_trampoline_handler(regs, &kretprobe_trampoline, &regs->sp);
+	return (void *)kretprobe_trampoline_handler(regs, &regs->sp);
 }
 NOKPROBE_SYMBOL(trampoline_handler);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/kprobes/opt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/kprobes/opt.c
@@ -15,6 +15,7 @@
 #include <linux/extable.h>
 #include <linux/kdebug.h>
 #include <linux/kallsyms.h>
+#include <linux/kgdb.h>
 #include <linux/ftrace.h>
 #include <linux/objtool.h>
 #include <linux/pgtable.h>
@@ -45,8 +46,8 @@
 		/* This function only handles jump-optimized kprobe */
 		if (kp && kprobe_optimized(kp)) {
 			op = container_of(kp, struct optimized_kprobe, kp);
-			/* If op->list is not empty, op is under optimizing */
-			if (list_empty(&op->list))
+			/* If op is optimized or under unoptimizing */
+			if (list_empty(&op->list) || optprobe_queued_unopt(op))
 				goto found;
 		}
 	}
@@ -272,19 +273,6 @@
 	return ret;
 }
 
-static bool is_padding_int3(unsigned long addr, unsigned long eaddr)
-{
-	unsigned char ops;
-
-	for (; addr < eaddr; addr++) {
-		if (get_kernel_nofault(ops, (void *)addr) < 0 ||
-		    ops != INT3_INSN_OPCODE)
-			return false;
-	}
-
-	return true;
-}
-
 /* Decode whole function to ensure any instructions don't jump into target */
 static int can_optimize(unsigned long paddr)
 {
@@ -327,15 +315,15 @@
 		ret = insn_decode_kernel(&insn, (void *)recovered_insn);
 		if (ret < 0)
 			return 0;
-
+#ifdef CONFIG_KGDB
 		/*
-		 * In the case of detecting unknown breakpoint, this could be
-		 * a padding INT3 between functions. Let's check that all the
-		 * rest of the bytes are also INT3.
+		 * If there is a dynamically installed kgdb sw breakpoint,
+		 * this function should not be probed.
 		 */
-		if (insn.opcode.bytes[0] == INT3_INSN_OPCODE)
-			return is_padding_int3(addr, paddr - offset + size) ? 1 : 0;
-
+		if (insn.opcode.bytes[0] == INT3_INSN_OPCODE &&
+		    kgdb_has_hit_break(addr))
+			return 0;
+#endif
 		/* Recover address */
 		insn.kaddr = (void *)addr;
 		insn.next_byte = (void *)(addr + insn.length);
@@ -358,7 +346,7 @@
 
 	for (i = 1; i < op->optinsn.size; i++) {
 		p = get_kprobe(op->kp.addr + i);
-		if (p && !kprobe_disabled(p))
+		if (p && !kprobe_disarmed(p))
 			return -EEXIST;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/ksysfs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/ksysfs.c
@@ -91,26 +91,41 @@
 
 static int __init get_setup_data_size(int nr, size_t *size)
 {
-	int i = 0;
+	u64 pa_data = boot_params.hdr.setup_data, pa_next;
+	struct setup_indirect *indirect;
 	struct setup_data *data;
-	u64 pa_data = boot_params.hdr.setup_data;
+	int i = 0;
+	u32 len;
 
 	while (pa_data) {
 		data = memremap(pa_data, sizeof(*data), MEMREMAP_WB);
 		if (!data)
 			return -ENOMEM;
+		pa_next = data->next;
+
 		if (nr == i) {
-			if (data->type == SETUP_INDIRECT &&
-			    ((struct setup_indirect *)data->data)->type != SETUP_INDIRECT)
-				*size = ((struct setup_indirect *)data->data)->len;
-			else
+			if (data->type == SETUP_INDIRECT) {
+				len = sizeof(*data) + data->len;
+				memunmap(data);
+				data = memremap(pa_data, len, MEMREMAP_WB);
+				if (!data)
+					return -ENOMEM;
+
+				indirect = (struct setup_indirect *)data->data;
+
+				if (indirect->type != SETUP_INDIRECT)
+					*size = indirect->len;
+				else
+					*size = data->len;
+			} else {
 				*size = data->len;
+			}
 
 			memunmap(data);
 			return 0;
 		}
 
-		pa_data = data->next;
+		pa_data = pa_next;
 		memunmap(data);
 		i++;
 	}
@@ -120,9 +135,11 @@
 static ssize_t type_show(struct kobject *kobj,
 			 struct kobj_attribute *attr, char *buf)
 {
+	struct setup_indirect *indirect;
+	struct setup_data *data;
 	int nr, ret;
 	u64 paddr;
-	struct setup_data *data;
+	u32 len;
 
 	ret = kobj_to_setup_data_nr(kobj, &nr);
 	if (ret)
@@ -135,10 +152,20 @@
 	if (!data)
 		return -ENOMEM;
 
-	if (data->type == SETUP_INDIRECT)
-		ret = sprintf(buf, "0x%x\n", ((struct setup_indirect *)data->data)->type);
-	else
+	if (data->type == SETUP_INDIRECT) {
+		len = sizeof(*data) + data->len;
+		memunmap(data);
+		data = memremap(paddr, len, MEMREMAP_WB);
+		if (!data)
+			return -ENOMEM;
+
+		indirect = (struct setup_indirect *)data->data;
+
+		ret = sprintf(buf, "0x%x\n", indirect->type);
+	} else {
 		ret = sprintf(buf, "0x%x\n", data->type);
+	}
+
 	memunmap(data);
 	return ret;
 }
@@ -149,9 +176,10 @@
 				    char *buf,
 				    loff_t off, size_t count)
 {
+	struct setup_indirect *indirect;
+	struct setup_data *data;
 	int nr, ret = 0;
 	u64 paddr, len;
-	struct setup_data *data;
 	void *p;
 
 	ret = kobj_to_setup_data_nr(kobj, &nr);
@@ -165,10 +193,27 @@
 	if (!data)
 		return -ENOMEM;
 
-	if (data->type == SETUP_INDIRECT &&
-	    ((struct setup_indirect *)data->data)->type != SETUP_INDIRECT) {
-		paddr = ((struct setup_indirect *)data->data)->addr;
-		len = ((struct setup_indirect *)data->data)->len;
+	if (data->type == SETUP_INDIRECT) {
+		len = sizeof(*data) + data->len;
+		memunmap(data);
+		data = memremap(paddr, len, MEMREMAP_WB);
+		if (!data)
+			return -ENOMEM;
+
+		indirect = (struct setup_indirect *)data->data;
+
+		if (indirect->type != SETUP_INDIRECT) {
+			paddr = indirect->addr;
+			len = indirect->len;
+		} else {
+			/*
+			 * Even though this is technically undefined, return
+			 * the data as though it is a normal setup_data struct.
+			 * This will at least allow it to be inspected.
+			 */
+			paddr += sizeof(*data);
+			len = data->len;
+		}
 	} else {
 		paddr += sizeof(*data);
 		len = data->len;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/kvm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/kvm.c
@@ -66,6 +66,7 @@
 DEFINE_PER_CPU_DECRYPTED(struct kvm_steal_time, steal_time) __aligned(64) __visible;
 static int has_steal_clock = 0;
 
+static int has_guest_poll = 0;
 /*
  * No need for any "IO delay" on KVM
  */
@@ -187,7 +188,7 @@
 {
 	u32 key = hash_32(token, KVM_TASK_SLEEP_HASHBITS);
 	struct kvm_task_sleep_head *b = &async_pf_sleepers[key];
-	struct kvm_task_sleep_node *n;
+	struct kvm_task_sleep_node *n, *dummy = NULL;
 
 	if (token == ~0) {
 		apf_task_wake_all();
@@ -199,28 +200,41 @@
 	n = _find_apf_task(b, token);
 	if (!n) {
 		/*
-		 * async PF was not yet handled.
-		 * Add dummy entry for the token.
+		 * Async #PF not yet handled, add a dummy entry for the token.
+		 * Allocating the token must be down outside of the raw lock
+		 * as the allocator is preemptible on PREEMPT_RT kernels.
 		 */
-		n = kzalloc(sizeof(*n), GFP_ATOMIC);
-		if (!n) {
+		if (!dummy) {
+			raw_spin_unlock(&b->lock);
+			dummy = kzalloc(sizeof(*dummy), GFP_ATOMIC);
+
 			/*
-			 * Allocation failed! Busy wait while other cpu
-			 * handles async PF.
+			 * Continue looping on allocation failure, eventually
+			 * the async #PF will be handled and allocating a new
+			 * node will be unnecessary.
+			 */
+			if (!dummy)
+				cpu_relax();
+
+			/*
+			 * Recheck for async #PF completion before enqueueing
+			 * the dummy token to avoid duplicate list entries.
 			 */
-			raw_spin_unlock(&b->lock);
-			cpu_relax();
 			goto again;
 		}
-		n->token = token;
-		n->cpu = smp_processor_id();
-		init_swait_queue_head(&n->wq);
-		hlist_add_head(&n->link, &b->list);
+		dummy->token = token;
+		dummy->cpu = smp_processor_id();
+		init_swait_queue_head(&dummy->wq);
+		hlist_add_head(&dummy->link, &b->list);
+		dummy = NULL;
 	} else {
 		apf_task_wake_one(n);
 	}
 	raw_spin_unlock(&b->lock);
-	return;
+
+	/* A dummy token might be allocated and ultimately not used.  */
+	if (dummy)
+		kfree(dummy);
 }
 EXPORT_SYMBOL_GPL(kvm_async_pf_task_wake);
 
@@ -457,19 +471,22 @@
 {
 	return (kvm_para_has_feature(KVM_FEATURE_PV_TLB_FLUSH) &&
 		!kvm_para_has_hint(KVM_HINTS_REALTIME) &&
-		kvm_para_has_feature(KVM_FEATURE_STEAL_TIME));
+		kvm_para_has_feature(KVM_FEATURE_STEAL_TIME) &&
+		(num_possible_cpus() != 1));
 }
 
 static bool pv_ipi_supported(void)
 {
-	return kvm_para_has_feature(KVM_FEATURE_PV_SEND_IPI);
+	return (kvm_para_has_feature(KVM_FEATURE_PV_SEND_IPI) &&
+	       (num_possible_cpus() != 1));
 }
 
 static bool pv_sched_yield_supported(void)
 {
 	return (kvm_para_has_feature(KVM_FEATURE_PV_SCHED_YIELD) &&
 		!kvm_para_has_hint(KVM_HINTS_REALTIME) &&
-	    kvm_para_has_feature(KVM_FEATURE_STEAL_TIME));
+	    kvm_para_has_feature(KVM_FEATURE_STEAL_TIME) &&
+	    (num_possible_cpus() != 1));
 }
 
 #define KVM_IPI_CLUSTER_SIZE	(2 * BITS_PER_LONG)
@@ -507,7 +524,7 @@
 		} else if (apic_id < min && max - apic_id < KVM_IPI_CLUSTER_SIZE) {
 			ipi_bitmap <<= min - apic_id;
 			min = apic_id;
-		} else if (apic_id < min + KVM_IPI_CLUSTER_SIZE) {
+		} else if (apic_id > min && apic_id < min + KVM_IPI_CLUSTER_SIZE) {
 			max = apic_id < max ? max : apic_id;
 		} else {
 			ret = kvm_hypercall4(KVM_HC_SEND_IPI, (unsigned long)ipi_bitmap,
@@ -647,14 +664,26 @@
 
 static int kvm_suspend(void)
 {
+	u64 val = 0;
+
 	kvm_guest_cpu_offline(false);
 
+#ifdef CONFIG_ARCH_CPUIDLE_HALTPOLL
+	if (kvm_para_has_feature(KVM_FEATURE_POLL_CONTROL))
+		rdmsrl(MSR_KVM_POLL_CONTROL, val);
+	has_guest_poll = !(val & 1);
+#endif
 	return 0;
 }
 
 static void kvm_resume(void)
 {
 	kvm_cpu_online(raw_smp_processor_id());
+
+#ifdef CONFIG_ARCH_CPUIDLE_HALTPOLL
+	if (kvm_para_has_feature(KVM_FEATURE_POLL_CONTROL) && has_guest_poll)
+		wrmsrl(MSR_KVM_POLL_CONTROL, 0);
+#endif
 }
 
 static struct syscore_ops kvm_syscore_ops = {
@@ -919,7 +948,7 @@
 "movq	__per_cpu_offset(,%rdi,8), %rax;"
 "cmpb	$0, " __stringify(KVM_STEAL_TIME_preempted) "+steal_time(%rax);"
 "setne	%al;"
-"ret;"
+ASM_RET
 ".size __raw_callee_save___kvm_vcpu_is_preempted, .-__raw_callee_save___kvm_vcpu_is_preempted;"
 ".popsection");
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/kvmclock.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/kvmclock.c
@@ -24,8 +24,8 @@
 
 static int kvmclock __initdata = 1;
 static int kvmclock_vsyscall __initdata = 1;
-static int msr_kvm_system_time __ro_after_init = MSR_KVM_SYSTEM_TIME;
-static int msr_kvm_wall_clock __ro_after_init = MSR_KVM_WALL_CLOCK;
+static int msr_kvm_system_time __ro_after_init;
+static int msr_kvm_wall_clock __ro_after_init;
 static u64 kvm_sched_clock_offset __ro_after_init;
 
 static int __init parse_no_kvmclock(char *arg)
@@ -195,7 +195,8 @@
 
 void kvmclock_disable(void)
 {
-	native_write_msr(msr_kvm_system_time, 0, 0);
+	if (msr_kvm_system_time)
+		native_write_msr(msr_kvm_system_time, 0, 0);
 }
 
 static void __init kvmclock_init_mem(void)
@@ -291,7 +292,10 @@
 	if (kvm_para_has_feature(KVM_FEATURE_CLOCKSOURCE2)) {
 		msr_kvm_system_time = MSR_KVM_SYSTEM_TIME_NEW;
 		msr_kvm_wall_clock = MSR_KVM_WALL_CLOCK_NEW;
-	} else if (!kvm_para_has_feature(KVM_FEATURE_CLOCKSOURCE)) {
+	} else if (kvm_para_has_feature(KVM_FEATURE_CLOCKSOURCE)) {
+		msr_kvm_system_time = MSR_KVM_SYSTEM_TIME;
+		msr_kvm_wall_clock = MSR_KVM_WALL_CLOCK;
+	} else {
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/machine_kexec_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/machine_kexec_64.c
@@ -373,9 +373,6 @@
 #ifdef CONFIG_KEXEC_FILE
 void *arch_kexec_kernel_image_load(struct kimage *image)
 {
-	vfree(image->elf_headers);
-	image->elf_headers = NULL;
-
 	if (!image->fops || !image->fops->load)
 		return ERR_PTR(-ENOEXEC);
 
@@ -511,6 +508,15 @@
 	       (int)ELF64_R_TYPE(rel[i].r_info), value);
 	return -ENOEXEC;
 }
+
+int arch_kimage_file_post_load_cleanup(struct kimage *image)
+{
+	vfree(image->elf_headers);
+	image->elf_headers = NULL;
+	image->elf_headers_sz = 0;
+
+	return kexec_image_post_load_cleanup_default(image);
+}
 #endif /* CONFIG_KEXEC_FILE */
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/module.c
@@ -67,6 +67,7 @@
 
 void *module_alloc(unsigned long size)
 {
+	gfp_t gfp_mask = GFP_KERNEL;
 	void *p;
 
 	if (PAGE_ALIGN(size) > MODULES_LEN)
@@ -74,10 +75,10 @@
 
 	p = __vmalloc_node_range(size, MODULE_ALIGN,
 				    MODULES_VADDR + get_module_load_offset(),
-				    MODULES_END, GFP_KERNEL,
-				    PAGE_KERNEL, 0, NUMA_NO_NODE,
+				    MODULES_END, gfp_mask,
+				    PAGE_KERNEL, VM_DEFER_KMEMLEAK, NUMA_NO_NODE,
 				    __builtin_return_address(0));
-	if (p && (kasan_module_alloc(p, size) < 0)) {
+	if (p && (kasan_module_alloc(p, size, gfp_mask) < 0)) {
 		vfree(p);
 		return NULL;
 	}
@@ -251,7 +252,8 @@
 		    struct module *me)
 {
 	const Elf_Shdr *s, *text = NULL, *alt = NULL, *locks = NULL,
-		*para = NULL, *orc = NULL, *orc_ip = NULL;
+		*para = NULL, *orc = NULL, *orc_ip = NULL,
+		*retpolines = NULL, *returns = NULL;
 	char *secstrings = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
 
 	for (s = sechdrs; s < sechdrs + hdr->e_shnum; s++) {
@@ -267,8 +269,28 @@
 			orc = s;
 		if (!strcmp(".orc_unwind_ip", secstrings + s->sh_name))
 			orc_ip = s;
+		if (!strcmp(".retpoline_sites", secstrings + s->sh_name))
+			retpolines = s;
+		if (!strcmp(".return_sites", secstrings + s->sh_name))
+			returns = s;
 	}
 
+	/*
+	 * See alternative_instructions() for the ordering rules between the
+	 * various patching types.
+	 */
+	if (para) {
+		void *pseg = (void *)para->sh_addr;
+		apply_paravirt(pseg, pseg + para->sh_size);
+	}
+	if (retpolines) {
+		void *rseg = (void *)retpolines->sh_addr;
+		apply_retpolines(rseg, rseg + retpolines->sh_size);
+	}
+	if (returns) {
+		void *rseg = (void *)returns->sh_addr;
+		apply_returns(rseg, rseg + returns->sh_size);
+	}
 	if (alt) {
 		/* patch .altinstructions */
 		void *aseg = (void *)alt->sh_addr;
@@ -282,11 +304,6 @@
 					    tseg, tseg + text->sh_size);
 	}
 
-	if (para) {
-		void *pseg = (void *)para->sh_addr;
-		apply_paravirt(pseg, pseg + para->sh_size);
-	}
-
 	/* make jump label nops */
 	jump_label_apply_nops(me);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/nmi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/nmi.c
@@ -519,9 +519,6 @@
 		write_cr2(this_cpu_read(nmi_cr2));
 	if (this_cpu_dec_return(nmi_state))
 		goto nmi_restart;
-
-	if (user_mode(regs))
-		mds_user_clear_cpu_buffers();
 }
 
 #if defined(CONFIG_X86_64) && IS_ENABLED(CONFIG_KVM_INTEL)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/paravirt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/paravirt.c
@@ -41,7 +41,7 @@
 asm (".pushsection .entry.text, \"ax\"\n"
      ".global _paravirt_nop\n"
      "_paravirt_nop:\n\t"
-     "ret\n\t"
+     ASM_RET
      ".size _paravirt_nop, . - _paravirt_nop\n\t"
      ".type _paravirt_nop, @function\n\t"
      ".popsection");
@@ -58,29 +58,12 @@
 	BUG();
 }
 
-struct branch {
-	unsigned char opcode;
-	u32 delta;
-} __attribute__((packed));
-
 static unsigned paravirt_patch_call(void *insn_buff, const void *target,
 				    unsigned long addr, unsigned len)
 {
-	const int call_len = 5;
-	struct branch *b = insn_buff;
-	unsigned long delta = (unsigned long)target - (addr+call_len);
-
-	if (len < call_len) {
-		pr_warn("paravirt: Failed to patch indirect CALL at %ps\n", (void *)addr);
-		/* Kernel might not be viable if patching fails, bail out: */
-		BUG_ON(1);
-	}
-
-	b->opcode = 0xe8; /* call */
-	b->delta = delta;
-	BUILD_BUG_ON(sizeof(*b) != call_len);
-
-	return call_len;
+	__text_gen_insn(insn_buff, CALL_INSN_OPCODE,
+			(void *)addr, target, CALL_INSN_SIZE);
+	return CALL_INSN_SIZE;
 }
 
 #ifdef CONFIG_PARAVIRT_XXL
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/pmem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/pmem.c
@@ -27,6 +27,11 @@
 	 * simply here to trigger the module to load on demand.
 	 */
 	pdev = platform_device_alloc("e820_pmem", -1);
-	return platform_device_add(pdev);
+
+	rc = platform_device_add(pdev);
+	if (rc)
+		platform_device_put(pdev);
+
+	return rc;
 }
 device_initcall(register_e820_pmem);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/process.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/process.c
@@ -30,7 +30,9 @@
 #include <asm/apic.h>
 #include <linux/uaccess.h>
 #include <asm/mwait.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
+#include <asm/fpu/sched.h>
+#include <asm/fpu/xstate.h>
 #include <asm/debugreg.h>
 #include <asm/nmi.h>
 #include <asm/tlbflush.h>
@@ -83,13 +85,29 @@
  */
 int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src)
 {
-	memcpy(dst, src, arch_task_struct_size);
+	/* init_task is not dynamically sized (incomplete FPU state) */
+	if (unlikely(src == &init_task))
+		memcpy_and_pad(dst, arch_task_struct_size, src, sizeof(init_task), 0);
+	else
+		memcpy(dst, src, arch_task_struct_size);
+
 #ifdef CONFIG_VM86
 	dst->thread.vm86 = NULL;
 #endif
-	return fpu_clone(dst);
+	/* Drop the copied pointer to current's fpstate */
+	dst->thread.fpu.fpstate = NULL;
+
+	return 0;
 }
 
+#ifdef CONFIG_X86_64
+void arch_release_task_struct(struct task_struct *tsk)
+{
+	if (fpu_state_size_dynamic())
+		fpstate_free(&tsk->thread.fpu);
+}
+#endif
+
 /*
  * Free thread data structures etc..
  */
@@ -132,6 +150,7 @@
 	frame->ret_addr = (unsigned long) ret_from_fork;
 	p->thread.sp = (unsigned long) fork_frame;
 	p->thread.io_bitmap = NULL;
+	p->thread.iopl_warn = 0;
 	memset(p->thread.ptrace_bps, 0, sizeof(p->thread.ptrace_bps));
 
 #ifdef CONFIG_X86_64
@@ -154,6 +173,8 @@
 	frame->flags = X86_EFLAGS_FIXED;
 #endif
 
+	fpu_clone(p, clone_flags);
+
 	/* Kernel thread ? */
 	if (unlikely(p->flags & PF_KTHREAD)) {
 		p->thread.pkru = pkru_get_init_value();
@@ -583,7 +604,7 @@
 	}
 
 	if (updmsr)
-		wrmsrl(MSR_IA32_SPEC_CTRL, msr);
+		update_spec_ctrl_cond(msr);
 }
 
 static unsigned long speculation_ctrl_update_tif(struct task_struct *tsk)
@@ -730,7 +751,7 @@
 }
 #endif
 
-void stop_this_cpu(void *dummy)
+void __noreturn stop_this_cpu(void *dummy)
 {
 	local_irq_disable();
 	/*
@@ -804,6 +825,10 @@
  */
 static int prefer_mwait_c1_over_halt(const struct cpuinfo_x86 *c)
 {
+	/* User has disallowed the use of MWAIT. Fallback to HALT */
+	if (boot_option_idle_override == IDLE_NOMWAIT)
+		return 0;
+
 	if (c->x86_vendor != X86_VENDOR_INTEL)
 		return 0;
 
@@ -912,9 +937,8 @@
 	} else if (!strcmp(str, "nomwait")) {
 		/*
 		 * If the boot option of "idle=nomwait" is added,
-		 * it means that mwait will be disabled for CPU C2/C3
-		 * states. In such case it won't touch the variable
-		 * of boot_option_idle_override.
+		 * it means that mwait will be disabled for CPU C1/C2/C3
+		 * states.
 		 */
 		boot_option_idle_override = IDLE_NOMWAIT;
 	} else
@@ -933,7 +957,10 @@
 
 unsigned long arch_randomize_brk(struct mm_struct *mm)
 {
-	return randomize_page(mm->brk, 0x02000000);
+	if (mmap_is_ia32())
+		return randomize_page(mm->brk, SZ_32M);
+
+	return randomize_page(mm->brk, SZ_1G);
 }
 
 /*
@@ -999,13 +1026,17 @@
 }
 
 long do_arch_prctl_common(struct task_struct *task, int option,
-			  unsigned long cpuid_enabled)
+			  unsigned long arg2)
 {
 	switch (option) {
 	case ARCH_GET_CPUID:
 		return get_cpuid_mode();
 	case ARCH_SET_CPUID:
-		return set_cpuid_mode(task, cpuid_enabled);
+		return set_cpuid_mode(task, arg2);
+	case ARCH_GET_XCOMP_SUPP:
+	case ARCH_GET_XCOMP_PERM:
+	case ARCH_REQ_XCOMP_PERM:
+		return fpu_xstate_prctl(task, option, arg2);
 	}
 
 	return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/process_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/process_32.c
@@ -41,7 +41,7 @@
 
 #include <asm/ldt.h>
 #include <asm/processor.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/sched.h>
 #include <asm/desc.h>
 
 #include <linux/err.h>
@@ -160,7 +160,6 @@
 	struct thread_struct *prev = &prev_p->thread,
 			     *next = &next_p->thread;
 	struct fpu *prev_fpu = &prev->fpu;
-	struct fpu *next_fpu = &next->fpu;
 	int cpu = smp_processor_id();
 
 	/* never put a printk in __switch_to... printk() calls wake_up*() indirectly */
@@ -213,10 +212,10 @@
 
 	this_cpu_write(current_task, next_p);
 
-	switch_fpu_finish(next_fpu);
+	switch_fpu_finish();
 
 	/* Load the Intel cache allocation PQR MSR. */
-	resctrl_sched_in();
+	resctrl_sched_in(next_p);
 
 	return prev_p;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/process_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/process_64.c
@@ -42,7 +42,7 @@
 
 #include <asm/processor.h>
 #include <asm/pkru.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/sched.h>
 #include <asm/mmu_context.h>
 #include <asm/prctl.h>
 #include <asm/desc.h>
@@ -137,7 +137,7 @@
 		       log_lvl, d3, d6, d7);
 	}
 
-	if (cpu_feature_enabled(X86_FEATURE_OSPKE))
+	if (cr4 & X86_CR4_PKE)
 		printk("%sPKRU: %08x\n", log_lvl, read_pkru());
 }
 
@@ -559,7 +559,6 @@
 	struct thread_struct *prev = &prev_p->thread;
 	struct thread_struct *next = &next_p->thread;
 	struct fpu *prev_fpu = &prev->fpu;
-	struct fpu *next_fpu = &next->fpu;
 	int cpu = smp_processor_id();
 
 	WARN_ON_ONCE(IS_ENABLED(CONFIG_DEBUG_ENTRY) &&
@@ -620,7 +619,7 @@
 	this_cpu_write(current_task, next_p);
 	this_cpu_write(cpu_current_top_of_stack, task_top_of_stack(next_p));
 
-	switch_fpu_finish(next_fpu);
+	switch_fpu_finish();
 
 	/* Reload sp0. */
 	update_task_stack(next_p);
@@ -656,7 +655,7 @@
 	}
 
 	/* Load the Intel cache allocation PQR MSR. */
-	resctrl_sched_in();
+	resctrl_sched_in(next_p);
 
 	return prev_p;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/ptrace.c
@@ -29,9 +29,9 @@
 
 #include <linux/uaccess.h>
 #include <asm/processor.h>
-#include <asm/fpu/internal.h>
 #include <asm/fpu/signal.h>
 #include <asm/fpu/regset.h>
+#include <asm/fpu/xstate.h>
 #include <asm/debugreg.h>
 #include <asm/ldt.h>
 #include <asm/desc.h>
@@ -1224,7 +1224,7 @@
 	},
 	[REGSET_FP] = {
 		.core_note_type = NT_PRFPREG,
-		.n = sizeof(struct user_i387_struct) / sizeof(long),
+		.n = sizeof(struct fxregs_state) / sizeof(long),
 		.size = sizeof(long), .align = sizeof(long),
 		.active = regset_xregset_fpregs_active, .regset_get = xfpregs_get, .set = xfpregs_set
 	},
@@ -1271,7 +1271,7 @@
 	},
 	[REGSET_XFP] = {
 		.core_note_type = NT_PRXFPREG,
-		.n = sizeof(struct user32_fxsr_struct) / sizeof(u32),
+		.n = sizeof(struct fxregs_state) / sizeof(u32),
 		.size = sizeof(u32), .align = sizeof(u32),
 		.active = regset_xregset_fpregs_active, .regset_get = xfpregs_get, .set = xfpregs_set
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/reboot.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/reboot.c
@@ -32,6 +32,7 @@
 #include <asm/realmode.h>
 #include <asm/x86_init.h>
 #include <asm/efi.h>
+#include <asm/nospec-branch.h>
 
 /*
  * Power off function, if any
@@ -113,17 +114,9 @@
 	spin_unlock(&rtc_lock);
 
 	/*
-	 * Switch back to the initial page table.
+	 * Switch to the trampoline page table.
 	 */
-#ifdef CONFIG_X86_32
-	load_cr3(initial_page_table);
-#else
-	write_cr3(real_mode_header->trampoline_pgd);
-
-	/* Exiting long mode will fail if CR4.PCIDE is set. */
-	if (boot_cpu_has(X86_FEATURE_PCID))
-		cr4_clear_bits(X86_CR4_PCIDE);
-#endif
+	load_trampoline_pgtable();
 
 	/* Jump to the identity-mapped low memory code */
 #ifdef CONFIG_X86_32
@@ -496,7 +489,46 @@
 			DMI_MATCH(DMI_PRODUCT_NAME, "VGN-Z540N"),
 		},
 	},
-
+	{	/* Handle problems with rebooting on the Latitude E6520. */
+		.callback = set_pci_reboot,
+		.ident = "Dell Latitude E6520",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E6520"),
+		},
+	},
+	{       /* Handle problems with rebooting on the OptiPlex 790. */
+		.callback = set_pci_reboot,
+		.ident = "Dell OptiPlex 790",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 790"),
+		},
+	},
+	{	/* Handle problems with rebooting on the OptiPlex 990. */
+		.callback = set_pci_reboot,
+		.ident = "Dell OptiPlex 990",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 990"),
+		},
+	},
+	{       /* Handle problems with rebooting on the Latitude E6220. */
+		.callback = set_pci_reboot,
+		.ident = "Dell Latitude E6220",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E6220"),
+		},
+	},
+	{	/* Handle problems with rebooting on the OptiPlex 390. */
+		.callback = set_pci_reboot,
+		.ident = "Dell OptiPlex 390",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 390"),
+		},
+	},
 	{ }
 };
 
@@ -536,33 +568,29 @@
 	}
 }
 
-static void vmxoff_nmi(int cpu, struct pt_regs *regs)
-{
-	cpu_emergency_vmxoff();
-}
+static inline void nmi_shootdown_cpus_on_restart(void);
 
-/* Use NMIs as IPIs to tell all CPUs to disable virtualization */
-static void emergency_vmx_disable_all(void)
+static void emergency_reboot_disable_virtualization(void)
 {
 	/* Just make sure we won't change CPUs while doing this */
 	local_irq_disable();
 
 	/*
-	 * Disable VMX on all CPUs before rebooting, otherwise we risk hanging
-	 * the machine, because the CPU blocks INIT when it's in VMX root.
+	 * Disable virtualization on all CPUs before rebooting to avoid hanging
+	 * the system, as VMX and SVM block INIT when running in the host.
 	 *
 	 * We can't take any locks and we may be on an inconsistent state, so
-	 * use NMIs as IPIs to tell the other CPUs to exit VMX root and halt.
+	 * use NMIs as IPIs to tell the other CPUs to disable VMX/SVM and halt.
 	 *
-	 * Do the NMI shootdown even if VMX if off on _this_ CPU, as that
-	 * doesn't prevent a different CPU from being in VMX root operation.
+	 * Do the NMI shootdown even if virtualization is off on _this_ CPU, as
+	 * other CPUs may have virtualization enabled.
 	 */
-	if (cpu_has_vmx()) {
-		/* Safely force _this_ CPU out of VMX root operation. */
-		__cpu_emergency_vmxoff();
+	if (cpu_has_vmx() || cpu_has_svm(NULL)) {
+		/* Safely force _this_ CPU out of VMX/SVM operation. */
+		cpu_emergency_disable_virtualization();
 
-		/* Halt and exit VMX root operation on the other CPUs. */
-		nmi_shootdown_cpus(vmxoff_nmi);
+		/* Disable VMX/SVM and halt on other CPUs. */
+		nmi_shootdown_cpus_on_restart();
 	}
 }
 
@@ -598,7 +626,7 @@
 	unsigned short mode;
 
 	if (reboot_emergency)
-		emergency_vmx_disable_all();
+		emergency_reboot_disable_virtualization();
 
 	tboot_shutdown(TB_SHUTDOWN_REBOOT);
 
@@ -803,6 +831,17 @@
 /* This is the CPU performing the emergency shutdown work. */
 int crashing_cpu = -1;
 
+/*
+ * Disable virtualization, i.e. VMX or SVM, to ensure INIT is recognized during
+ * reboot.  VMX blocks INIT if the CPU is post-VMXON, and SVM blocks INIT if
+ * GIF=0, i.e. if the crash occurred between CLGI and STGI.
+ */
+void cpu_emergency_disable_virtualization(void)
+{
+	cpu_emergency_vmxoff();
+	cpu_emergency_svm_disable();
+}
+
 #if defined(CONFIG_SMP)
 
 static nmi_shootdown_cb shootdown_callback;
@@ -825,7 +864,14 @@
 		return NMI_HANDLED;
 	local_irq_disable();
 
-	shootdown_callback(cpu, regs);
+	if (shootdown_callback)
+		shootdown_callback(cpu, regs);
+
+	/*
+	 * Prepare the CPU for reboot _after_ invoking the callback so that the
+	 * callback can safely use virtualization instructions, e.g. VMCLEAR.
+	 */
+	cpu_emergency_disable_virtualization();
 
 	atomic_dec(&waiting_for_crash_ipi);
 	/* Assume hlt works */
@@ -836,18 +882,32 @@
 	return NMI_HANDLED;
 }
 
-/*
- * Halt all other CPUs, calling the specified function on each of them
+/**
+ * nmi_shootdown_cpus - Stop other CPUs via NMI
+ * @callback:	Optional callback to be invoked from the NMI handler
+ *
+ * The NMI handler on the remote CPUs invokes @callback, if not
+ * NULL, first and then disables virtualization to ensure that
+ * INIT is recognized during reboot.
  *
- * This function can be used to halt all other CPUs on crash
- * or emergency reboot time. The function passed as parameter
- * will be called inside a NMI handler on all CPUs.
+ * nmi_shootdown_cpus() can only be invoked once. After the first
+ * invocation all other CPUs are stuck in crash_nmi_callback() and
+ * cannot respond to a second NMI.
  */
 void nmi_shootdown_cpus(nmi_shootdown_cb callback)
 {
 	unsigned long msecs;
+
 	local_irq_disable();
 
+	/*
+	 * Avoid certain doom if a shootdown already occurred; re-registering
+	 * the NMI handler will cause list corruption, modifying the callback
+	 * will do who knows what, etc...
+	 */
+	if (WARN_ON_ONCE(crash_ipi_issued))
+		return;
+
 	/* Make a note of crashing cpu. Will be used in NMI callback. */
 	crashing_cpu = safe_smp_processor_id();
 
@@ -875,7 +935,17 @@
 		msecs--;
 	}
 
-	/* Leave the nmi callback set */
+	/*
+	 * Leave the nmi callback set, shootdown is a one-time thing.  Clearing
+	 * the callback could result in a NULL pointer dereference if a CPU
+	 * (finally) responds after the timeout expires.
+	 */
+}
+
+static inline void nmi_shootdown_cpus_on_restart(void)
+{
+	if (!crash_ipi_issued)
+		nmi_shootdown_cpus(NULL);
 }
 
 /*
@@ -905,6 +975,8 @@
 	/* No other CPUs to shoot down */
 }
 
+static inline void nmi_shootdown_cpus_on_restart(void) { }
+
 void run_crash_ipi_callback(struct pt_regs *regs)
 {
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/relocate_kernel_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/relocate_kernel_32.S
@@ -7,10 +7,13 @@
 #include <linux/linkage.h>
 #include <asm/page_types.h>
 #include <asm/kexec.h>
+#include <asm/nospec-branch.h>
 #include <asm/processor-flags.h>
+#include <asm/nospec-branch.h>
 
 /*
- * Must be relocatable PIC code callable as a C function
+ * Must be relocatable PIC code callable as a C function, in particular
+ * there must be a plain RET and not jump to return thunk.
  */
 
 #define PTR(x) (x << 2)
@@ -91,7 +94,9 @@
 	movl    %edi, %eax
 	addl    $(identity_mapped - relocate_kernel), %eax
 	pushl   %eax
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(relocate_kernel)
 
 SYM_CODE_START_LOCAL_NOALIGN(identity_mapped)
@@ -159,12 +164,15 @@
 	xorl    %edx, %edx
 	xorl    %esi, %esi
 	xorl    %ebp, %ebp
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 1:
 	popl	%edx
 	movl	CP_PA_SWAP_PAGE(%edi), %esp
 	addl	$PAGE_SIZE, %esp
 2:
+	ANNOTATE_RETPOLINE_SAFE
 	call	*%edx
 
 	/* get the re-entry point of the peer system */
@@ -190,7 +198,9 @@
 	movl	%edi, %eax
 	addl	$(virtual_mapped - relocate_kernel), %eax
 	pushl	%eax
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(identity_mapped)
 
 SYM_CODE_START_LOCAL_NOALIGN(virtual_mapped)
@@ -208,7 +218,9 @@
 	popl	%edi
 	popl	%esi
 	popl	%ebx
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(virtual_mapped)
 
 	/* Do the copies */
@@ -271,7 +283,9 @@
 	popl	%edi
 	popl	%ebx
 	popl	%ebp
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(swap_pages)
 
 	.globl kexec_control_code_size
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/relocate_kernel_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/relocate_kernel_64.S
@@ -13,7 +13,8 @@
 #include <asm/unwind_hints.h>
 
 /*
- * Must be relocatable PIC code callable as a C function
+ * Must be relocatable PIC code callable as a C function, in particular
+ * there must be a plain RET and not jump to return thunk.
  */
 
 #define PTR(x) (x << 3)
@@ -104,7 +105,9 @@
 	/* jump to identity mapped page */
 	addq	$(identity_mapped - relocate_kernel), %r8
 	pushq	%r8
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(relocate_kernel)
 
 SYM_CODE_START_LOCAL_NOALIGN(identity_mapped)
@@ -191,7 +194,9 @@
 	xorl	%r14d, %r14d
 	xorl	%r15d, %r15d
 
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 
 1:
 	popq	%rdx
@@ -210,7 +215,9 @@
 	call	swap_pages
 	movq	$virtual_mapped, %rax
 	pushq	%rax
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(identity_mapped)
 
 SYM_CODE_START_LOCAL_NOALIGN(virtual_mapped)
@@ -231,7 +238,9 @@
 	popq	%r12
 	popq	%rbp
 	popq	%rbx
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(virtual_mapped)
 
 	/* Do the copies */
@@ -288,7 +297,9 @@
 	lea	PAGE_SIZE(%rax), %rsi
 	jmp	0b
 3:
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_CODE_END(swap_pages)
 
 	.globl kexec_control_code_size
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/resource.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/resource.c
@@ -1,6 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <linux/ioport.h>
+#include <linux/printk.h>
 #include <asm/e820/api.h>
+#include <asm/pci_x86.h>
 
 static void resource_clip(struct resource *res, resource_size_t start,
 			  resource_size_t end)
@@ -27,12 +29,23 @@
 {
 	int i;
 	struct e820_entry *entry;
+	u64 e820_start, e820_end;
+	struct resource orig = *avail;
+
+	if (!pci_use_e820)
+		return;
 
 	for (i = 0; i < e820_table->nr_entries; i++) {
 		entry = &e820_table->entries[i];
+		e820_start = entry->addr;
+		e820_end = entry->addr + entry->size - 1;
 
-		resource_clip(avail, entry->addr,
-			      entry->addr + entry->size - 1);
+		resource_clip(avail, e820_start, e820_end);
+		if (orig.start != avail->start || orig.end != avail->end) {
+			pr_info("clipped %pR to %pR for e820 entry [mem %#010Lx-%#010Lx]\n",
+				 &orig, avail, e820_start, e820_end);
+			orig = *avail;
+		}
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/setup.c
@@ -20,6 +20,7 @@
 #include <linux/root_dev.h>
 #include <linux/hugetlb.h>
 #include <linux/tboot.h>
+#include <linux/security.h>
 #include <linux/usb/xhci-dbgp.h>
 #include <linux/static_call.h>
 #include <linux/swiotlb.h>
@@ -66,11 +67,6 @@
 #endif
 
 
-/*
- * Range of the BSS area. The size of the BSS area is determined
- * at link time, with RESERVE_BRK() facility reserving additional
- * chunks.
- */
 unsigned long _brk_start = (unsigned long)__brk_base;
 unsigned long _brk_end   = (unsigned long)__brk_base;
 
@@ -368,21 +364,41 @@
 
 static void __init memblock_x86_reserve_range_setup_data(void)
 {
+	struct setup_indirect *indirect;
 	struct setup_data *data;
-	u64 pa_data;
+	u64 pa_data, pa_next;
+	u32 len;
 
 	pa_data = boot_params.hdr.setup_data;
 	while (pa_data) {
 		data = early_memremap(pa_data, sizeof(*data));
+		if (!data) {
+			pr_warn("setup: failed to memremap setup_data entry\n");
+			return;
+		}
+
+		len = sizeof(*data);
+		pa_next = data->next;
+
 		memblock_reserve(pa_data, sizeof(*data) + data->len);
 
-		if (data->type == SETUP_INDIRECT &&
-		    ((struct setup_indirect *)data->data)->type != SETUP_INDIRECT)
-			memblock_reserve(((struct setup_indirect *)data->data)->addr,
-					 ((struct setup_indirect *)data->data)->len);
+		if (data->type == SETUP_INDIRECT) {
+			len += data->len;
+			early_memunmap(data, sizeof(*data));
+			data = early_memremap(pa_data, len);
+			if (!data) {
+				pr_warn("setup: failed to memremap indirect setup_data\n");
+				return;
+			}
 
-		pa_data = data->next;
-		early_memunmap(data, sizeof(*data));
+			indirect = (struct setup_indirect *)data->data;
+
+			if (indirect->type != SETUP_INDIRECT)
+				memblock_reserve(indirect->addr, indirect->len);
+		}
+
+		pa_data = pa_next;
+		early_memunmap(data, len);
 	}
 }
 
@@ -713,9 +729,6 @@
 
 	early_reserve_initrd();
 
-	if (efi_enabled(EFI_BOOT))
-		efi_memblock_x86_reserve_range();
-
 	memblock_x86_reserve_range_setup_data();
 
 	reserve_ibft_region();
@@ -890,6 +903,9 @@
 
 	parse_early_param();
 
+	if (efi_enabled(EFI_BOOT))
+		efi_memblock_x86_reserve_range();
+
 #ifdef CONFIG_MEMORY_HOTPLUG
 	/*
 	 * Memory used by the kernel cannot be hot-removed because Linux
@@ -929,6 +945,13 @@
 	if (efi_enabled(EFI_BOOT))
 		efi_init();
 
+	efi_set_secure_boot(boot_params.secure_boot);
+
+#ifdef CONFIG_LOCK_DOWN_IN_SECURE_BOOT
+	if (efi_enabled(EFI_SECURE_BOOT))
+		security_lock_kernel_down("EFI Secure Boot mode", LOCKDOWN_INTEGRITY_MAX);
+#endif
+
 	dmi_setup();
 
 	/*
@@ -1094,19 +1117,7 @@
 	/* Allocate bigger log buffer */
 	setup_log_buf(1);
 
-	if (efi_enabled(EFI_BOOT)) {
-		switch (boot_params.secure_boot) {
-		case efi_secureboot_mode_disabled:
-			pr_info("Secure boot disabled\n");
-			break;
-		case efi_secureboot_mode_enabled:
-			pr_info("Secure boot enabled\n");
-			break;
-		default:
-			pr_info("Secure boot could not be determined\n");
-			break;
-		}
-	}
+	efi_set_secure_boot(boot_params.secure_boot);
 
 	reserve_initrd();
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/sev-shared.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/sev-shared.c
@@ -10,8 +10,13 @@
  */
 
 #ifndef __BOOT_COMPRESSED
-#define error(v)	pr_err(v)
-#define has_cpuflag(f)	boot_cpu_has(f)
+#define error(v)			pr_err(v)
+#define has_cpuflag(f)			boot_cpu_has(f)
+#define sev_printk(fmt, ...)		printk(fmt, ##__VA_ARGS__)
+#define sev_printk_rtl(fmt, ...)	printk_ratelimited(fmt, ##__VA_ARGS__)
+#else
+#define sev_printk(fmt, ...)
+#define sev_printk_rtl(fmt, ...)
 #endif
 
 static bool __init sev_es_check_cpu_features(void)
@@ -148,11 +153,16 @@
 {
 	unsigned int fn = lower_bits(regs->ax, 32);
 	unsigned long val;
+	u16 opcode = *(unsigned short *)regs->ip;
 
 	/* Only CPUID is supported via MSR protocol */
 	if (exit_code != SVM_EXIT_CPUID)
 		goto fail;
 
+	/* Is it really a CPUID insn? */
+	if (opcode != 0xa20f)
+		goto fail;
+
 	sev_es_wr_ghcb_msr(GHCB_CPUID_REQ(fn, GHCB_CPUID_REQ_EAX));
 	VMGEXIT();
 	val = sev_es_rd_ghcb_msr();
@@ -213,6 +223,23 @@
 	sev_es_terminate(GHCB_SEV_ES_REASON_GENERAL_REQUEST);
 }
 
+static enum es_result vc_insn_string_check(struct es_em_ctxt *ctxt,
+					   unsigned long address,
+					   bool write)
+{
+	if (user_mode(ctxt->regs) && fault_in_kernel_space(address)) {
+		ctxt->fi.vector     = X86_TRAP_PF;
+		ctxt->fi.error_code = X86_PF_USER;
+		ctxt->fi.cr2        = address;
+		if (write)
+			ctxt->fi.error_code |= X86_PF_WRITE;
+
+		return ES_EXCEPTION;
+	}
+
+	return ES_OK;
+}
+
 static enum es_result vc_insn_string_read(struct es_em_ctxt *ctxt,
 					  void *src, char *buf,
 					  unsigned int data_size,
@@ -220,7 +247,12 @@
 					  bool backwards)
 {
 	int i, b = backwards ? -1 : 1;
-	enum es_result ret = ES_OK;
+	unsigned long address = (unsigned long)src;
+	enum es_result ret;
+
+	ret = vc_insn_string_check(ctxt, address, false);
+	if (ret != ES_OK)
+		return ret;
 
 	for (i = 0; i < count; i++) {
 		void *s = src + (i * data_size * b);
@@ -241,7 +273,12 @@
 					   bool backwards)
 {
 	int i, s = backwards ? -1 : 1;
-	enum es_result ret = ES_OK;
+	unsigned long address = (unsigned long)dst;
+	enum es_result ret;
+
+	ret = vc_insn_string_check(ctxt, address, true);
+	if (ret != ES_OK)
+		return ret;
 
 	for (i = 0; i < count; i++) {
 		void *d = dst + (i * data_size * s);
@@ -277,6 +314,9 @@
 static enum es_result vc_ioio_exitinfo(struct es_em_ctxt *ctxt, u64 *exitinfo)
 {
 	struct insn *insn = &ctxt->insn;
+	size_t size;
+	u64 port;
+
 	*exitinfo = 0;
 
 	switch (insn->opcode.bytes[0]) {
@@ -285,7 +325,7 @@
 	case 0x6d:
 		*exitinfo |= IOIO_TYPE_INS;
 		*exitinfo |= IOIO_SEG_ES;
-		*exitinfo |= (ctxt->regs->dx & 0xffff) << 16;
+		port	   = ctxt->regs->dx & 0xffff;
 		break;
 
 	/* OUTS opcodes */
@@ -293,41 +333,43 @@
 	case 0x6f:
 		*exitinfo |= IOIO_TYPE_OUTS;
 		*exitinfo |= IOIO_SEG_DS;
-		*exitinfo |= (ctxt->regs->dx & 0xffff) << 16;
+		port	   = ctxt->regs->dx & 0xffff;
 		break;
 
 	/* IN immediate opcodes */
 	case 0xe4:
 	case 0xe5:
 		*exitinfo |= IOIO_TYPE_IN;
-		*exitinfo |= (u8)insn->immediate.value << 16;
+		port	   = (u8)insn->immediate.value & 0xffff;
 		break;
 
 	/* OUT immediate opcodes */
 	case 0xe6:
 	case 0xe7:
 		*exitinfo |= IOIO_TYPE_OUT;
-		*exitinfo |= (u8)insn->immediate.value << 16;
+		port	   = (u8)insn->immediate.value & 0xffff;
 		break;
 
 	/* IN register opcodes */
 	case 0xec:
 	case 0xed:
 		*exitinfo |= IOIO_TYPE_IN;
-		*exitinfo |= (ctxt->regs->dx & 0xffff) << 16;
+		port	   = ctxt->regs->dx & 0xffff;
 		break;
 
 	/* OUT register opcodes */
 	case 0xee:
 	case 0xef:
 		*exitinfo |= IOIO_TYPE_OUT;
-		*exitinfo |= (ctxt->regs->dx & 0xffff) << 16;
+		port	   = ctxt->regs->dx & 0xffff;
 		break;
 
 	default:
 		return ES_DECODE_FAILED;
 	}
 
+	*exitinfo |= port << 16;
+
 	switch (insn->opcode.bytes[0]) {
 	case 0x6c:
 	case 0x6e:
@@ -337,12 +379,15 @@
 	case 0xee:
 		/* Single byte opcodes */
 		*exitinfo |= IOIO_DATA_8;
+		size       = 1;
 		break;
 	default:
 		/* Length determined by instruction parsing */
 		*exitinfo |= (insn->opnd_bytes == 2) ? IOIO_DATA_16
 						     : IOIO_DATA_32;
+		size       = (insn->opnd_bytes == 2) ? 2 : 4;
 	}
+
 	switch (insn->addr_bytes) {
 	case 2:
 		*exitinfo |= IOIO_ADDR_16;
@@ -358,7 +403,7 @@
 	if (insn_has_rep_prefix(insn))
 		*exitinfo |= IOIO_REP;
 
-	return ES_OK;
+	return vc_ioio_check(ctxt, (u16)port, size);
 }
 
 static enum es_result vc_handle_ioio(struct ghcb *ghcb, struct es_em_ctxt *ctxt)
@@ -526,3 +571,94 @@
 
 	return ES_OK;
 }
+
+static enum es_result vc_check_opcode_bytes(struct es_em_ctxt *ctxt,
+					    unsigned long exit_code)
+{
+	unsigned int opcode = (unsigned int)ctxt->insn.opcode.value;
+	u8 modrm = ctxt->insn.modrm.value;
+
+	switch (exit_code) {
+
+	case SVM_EXIT_IOIO:
+	case SVM_EXIT_NPF:
+		/* handled separately */
+		return ES_OK;
+
+	case SVM_EXIT_CPUID:
+		if (opcode == 0xa20f)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_INVD:
+		if (opcode == 0x080f)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_MONITOR:
+		/* MONITOR and MONITORX instructions generate the same error code */
+		if (opcode == 0x010f && (modrm == 0xc8 || modrm == 0xfa))
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_MWAIT:
+		/* MWAIT and MWAITX instructions generate the same error code */
+		if (opcode == 0x010f && (modrm == 0xc9 || modrm == 0xfb))
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_MSR:
+		/* RDMSR */
+		if (opcode == 0x320f ||
+		/* WRMSR */
+		    opcode == 0x300f)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_RDPMC:
+		if (opcode == 0x330f)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_RDTSC:
+		if (opcode == 0x310f)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_RDTSCP:
+		if (opcode == 0x010f && modrm == 0xf9)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_READ_DR7:
+		if (opcode == 0x210f &&
+		    X86_MODRM_REG(ctxt->insn.modrm.value) == 7)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_VMMCALL:
+		if (opcode == 0x010f && modrm == 0xd9)
+			return ES_OK;
+
+		break;
+
+	case SVM_EXIT_WRITE_DR7:
+		if (opcode == 0x230f &&
+		    X86_MODRM_REG(ctxt->insn.modrm.value) == 7)
+			return ES_OK;
+		break;
+
+	case SVM_EXIT_WBINVD:
+		if (opcode == 0x90f)
+			return ES_OK;
+		break;
+
+	default:
+		break;
+	}
+
+	sev_printk(KERN_ERR "Wrong/unhandled opcode bytes: 0x%x, exit_code: 0x%lx, rIP: 0x%lx\n",
+		   opcode, exit_code, ctxt->regs->ip);
+
+	return ES_UNSUPPORTED;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/sev.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/sev.c
@@ -23,7 +23,7 @@
 #include <asm/stacktrace.h>
 #include <asm/sev.h>
 #include <asm/insn-eval.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/xcr.h>
 #include <asm/processor.h>
 #include <asm/realmode.h>
 #include <asm/traps.h>
@@ -46,16 +46,6 @@
 struct sev_es_runtime_data {
 	struct ghcb ghcb_page;
 
-	/* Physical storage for the per-CPU IST stack of the #VC handler */
-	char ist_stack[EXCEPTION_STKSZ] __aligned(PAGE_SIZE);
-
-	/*
-	 * Physical storage for the per-CPU fall-back stack of the #VC handler.
-	 * The fall-back stack is used when it is not safe to switch back to the
-	 * interrupted stack in the #VC entry code.
-	 */
-	char fallback_stack[EXCEPTION_STKSZ] __aligned(PAGE_SIZE);
-
 	/*
 	 * Reserve one page per CPU as backup storage for the unencrypted GHCB.
 	 * It is needed when an NMI happens while the #VC handler uses the real
@@ -99,27 +89,6 @@
 /* Needed in vc_early_forward_exception */
 void do_early_exception(struct pt_regs *regs, int trapnr);
 
-static void __init setup_vc_stacks(int cpu)
-{
-	struct sev_es_runtime_data *data;
-	struct cpu_entry_area *cea;
-	unsigned long vaddr;
-	phys_addr_t pa;
-
-	data = per_cpu(runtime_data, cpu);
-	cea  = get_cpu_entry_area(cpu);
-
-	/* Map #VC IST stack */
-	vaddr = CEA_ESTACK_BOT(&cea->estacks, VC);
-	pa    = __pa(data->ist_stack);
-	cea_set_pte((void *)vaddr, pa, PAGE_KERNEL);
-
-	/* Map VC fall-back stack */
-	vaddr = CEA_ESTACK_BOT(&cea->estacks, VC2);
-	pa    = __pa(data->fallback_stack);
-	cea_set_pte((void *)vaddr, pa, PAGE_KERNEL);
-}
-
 static __always_inline bool on_vc_stack(struct pt_regs *regs)
 {
 	unsigned long sp = regs->sp;
@@ -325,11 +294,6 @@
 				   char *dst, char *buf, size_t size)
 {
 	unsigned long error_code = X86_PF_PROT | X86_PF_WRITE;
-	char __user *target = (char __user *)dst;
-	u64 d8;
-	u32 d4;
-	u16 d2;
-	u8  d1;
 
 	/*
 	 * This function uses __put_user() independent of whether kernel or user
@@ -351,26 +315,42 @@
 	 * instructions here would cause infinite nesting.
 	 */
 	switch (size) {
-	case 1:
+	case 1: {
+		u8 d1;
+		u8 __user *target = (u8 __user *)dst;
+
 		memcpy(&d1, buf, 1);
 		if (__put_user(d1, target))
 			goto fault;
 		break;
-	case 2:
+	}
+	case 2: {
+		u16 d2;
+		u16 __user *target = (u16 __user *)dst;
+
 		memcpy(&d2, buf, 2);
 		if (__put_user(d2, target))
 			goto fault;
 		break;
-	case 4:
+	}
+	case 4: {
+		u32 d4;
+		u32 __user *target = (u32 __user *)dst;
+
 		memcpy(&d4, buf, 4);
 		if (__put_user(d4, target))
 			goto fault;
 		break;
-	case 8:
+	}
+	case 8: {
+		u64 d8;
+		u64 __user *target = (u64 __user *)dst;
+
 		memcpy(&d8, buf, 8);
 		if (__put_user(d8, target))
 			goto fault;
 		break;
+	}
 	default:
 		WARN_ONCE(1, "%s: Invalid size: %zu\n", __func__, size);
 		return ES_UNSUPPORTED;
@@ -393,11 +373,6 @@
 				  char *src, char *buf, size_t size)
 {
 	unsigned long error_code = X86_PF_PROT;
-	char __user *s = (char __user *)src;
-	u64 d8;
-	u32 d4;
-	u16 d2;
-	u8  d1;
 
 	/*
 	 * This function uses __get_user() independent of whether kernel or user
@@ -419,26 +394,41 @@
 	 * instructions here would cause infinite nesting.
 	 */
 	switch (size) {
-	case 1:
+	case 1: {
+		u8 d1;
+		u8 __user *s = (u8 __user *)src;
+
 		if (__get_user(d1, s))
 			goto fault;
 		memcpy(buf, &d1, 1);
 		break;
-	case 2:
+	}
+	case 2: {
+		u16 d2;
+		u16 __user *s = (u16 __user *)src;
+
 		if (__get_user(d2, s))
 			goto fault;
 		memcpy(buf, &d2, 2);
 		break;
-	case 4:
+	}
+	case 4: {
+		u32 d4;
+		u32 __user *s = (u32 __user *)src;
+
 		if (__get_user(d4, s))
 			goto fault;
 		memcpy(buf, &d4, 4);
 		break;
-	case 8:
+	}
+	case 8: {
+		u64 d8;
+		u64 __user *s = (u64 __user *)src;
 		if (__get_user(d8, s))
 			goto fault;
 		memcpy(buf, &d8, 8);
 		break;
+	}
 	default:
 		WARN_ONCE(1, "%s: Invalid size: %zu\n", __func__, size);
 		return ES_UNSUPPORTED;
@@ -492,6 +482,33 @@
 	return ES_OK;
 }
 
+static enum es_result vc_ioio_check(struct es_em_ctxt *ctxt, u16 port, size_t size)
+{
+	BUG_ON(size > 4);
+
+	if (user_mode(ctxt->regs)) {
+		struct thread_struct *t = &current->thread;
+		struct io_bitmap *iobm = t->io_bitmap;
+		size_t idx;
+
+		if (!iobm)
+			goto fault;
+
+		for (idx = port; idx < port + size; ++idx) {
+			if (test_bit(idx, iobm->bitmap))
+				goto fault;
+		}
+	}
+
+	return ES_OK;
+
+fault:
+	ctxt->fi.vector = X86_TRAP_GP;
+	ctxt->fi.error_code = 0;
+
+	return ES_EXCEPTION;
+}
+
 /* Include code shared with pre-decompression boot stage */
 #include "sev-shared.c"
 
@@ -787,7 +804,6 @@
 	for_each_possible_cpu(cpu) {
 		alloc_runtime_data(cpu);
 		init_ghcb(cpu);
-		setup_vc_stacks(cpu);
 	}
 
 	sev_es_setup_play_dead();
@@ -1015,6 +1031,9 @@
 	enum es_result ret;
 	long *reg_data;
 
+	if (user_mode(ctxt->regs))
+		return ES_UNSUPPORTED;
+
 	switch (insn->opcode.bytes[0]) {
 	/* MMIO Write */
 	case 0x88:
@@ -1235,7 +1254,10 @@
 					 struct ghcb *ghcb,
 					 unsigned long exit_code)
 {
-	enum es_result result;
+	enum es_result result = vc_check_opcode_bytes(ctxt, exit_code);
+
+	if (result != ES_OK)
+		return result;
 
 	switch (exit_code) {
 	case SVM_EXIT_READ_DR7:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/sev_verify_cbit.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/sev_verify_cbit.S
@@ -85,5 +85,5 @@
 #endif
 	/* Return page-table pointer */
 	movq	%rdi, %rax
-	ret
+	RET
 SYM_FUNC_END(sev_verify_cbit)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/signal.c
@@ -15,6 +15,7 @@
 #include <linux/mm.h>
 #include <linux/smp.h>
 #include <linux/kernel.h>
+#include <linux/kstrtox.h>
 #include <linux/errno.h>
 #include <linux/wait.h>
 #include <linux/tracehook.h>
@@ -30,8 +31,8 @@
 
 #include <asm/processor.h>
 #include <asm/ucontext.h>
-#include <asm/fpu/internal.h>
 #include <asm/fpu/signal.h>
+#include <asm/fpu/xstate.h>
 #include <asm/vdso.h>
 #include <asm/mce.h>
 #include <asm/sighandling.h>
@@ -41,6 +42,7 @@
 #include <linux/compat.h>
 #include <asm/proto.h>
 #include <asm/ia32_unistd.h>
+#include <asm/fpu/xstate.h>
 #endif /* CONFIG_X86_64 */
 
 #include <asm/syscall.h>
@@ -79,9 +81,9 @@
 # define CONTEXT_COPY_SIZE	sizeof(struct sigcontext)
 #endif
 
-static int restore_sigcontext(struct pt_regs *regs,
-			      struct sigcontext __user *usc,
-			      unsigned long uc_flags)
+static bool restore_sigcontext(struct pt_regs *regs,
+			       struct sigcontext __user *usc,
+			       unsigned long uc_flags)
 {
 	struct sigcontext sc;
 
@@ -89,7 +91,7 @@
 	current->restart_block.fn = do_no_restart_syscall;
 
 	if (copy_from_user(&sc, usc, CONTEXT_COPY_SIZE))
-		return -EFAULT;
+		return false;
 
 #ifdef CONFIG_X86_32
 	set_user_gs(regs, sc.gs);
@@ -244,7 +246,6 @@
 	unsigned long math_size = 0;
 	unsigned long sp = regs->sp;
 	unsigned long buf_fx = 0;
-	int ret;
 
 	/* redzone */
 	if (IS_ENABLED(CONFIG_X86_64))
@@ -292,8 +293,7 @@
 	}
 
 	/* save i387 and extended state */
-	ret = copy_fpstate_to_sigframe(*fpstate, (void __user *)buf_fx, math_size);
-	if (ret < 0)
+	if (!copy_fpstate_to_sigframe(*fpstate, (void __user *)buf_fx, math_size))
 		return (void __user *)-1L;
 
 	return (void __user *)sp;
@@ -643,7 +643,7 @@
 	 * x86_32 has no uc_flags bits relevant to restore_sigcontext.
 	 * Save a few cycles by skipping the __get_user.
 	 */
-	if (restore_sigcontext(regs, &frame->sc, 0))
+	if (!restore_sigcontext(regs, &frame->sc, 0))
 		goto badframe;
 	return regs->ax;
 
@@ -671,7 +671,7 @@
 
 	set_current_blocked(&set);
 
-	if (restore_sigcontext(regs, &frame->uc.uc_mcontext, uc_flags))
+	if (!restore_sigcontext(regs, &frame->uc.uc_mcontext, uc_flags))
 		goto badframe;
 
 	if (restore_altstack(&frame->uc.uc_stack))
@@ -721,18 +721,23 @@
 
 /* max_frame_size tells userspace the worst case signal stack size. */
 static unsigned long __ro_after_init max_frame_size;
+static unsigned int __ro_after_init fpu_default_state_size;
 
-void __init init_sigframe_size(void)
+static int __init init_sigframe_size(void)
 {
+	fpu_default_state_size = fpu__get_fpstate_size();
+
 	max_frame_size = MAX_FRAME_SIGINFO_UCTXT_SIZE + MAX_FRAME_PADDING;
 
-	max_frame_size += fpu__get_fpstate_size() + MAX_XSAVE_PADDING;
+	max_frame_size += fpu_default_state_size + MAX_XSAVE_PADDING;
 
 	/* Userspace expects an aligned size. */
 	max_frame_size = round_up(max_frame_size, FRAME_ALIGNMENT);
 
 	pr_info("max sigframe size: %lu\n", max_frame_size);
+	return 0;
 }
+early_initcall(init_sigframe_size);
 
 unsigned long get_sigframe_size(void)
 {
@@ -910,6 +915,62 @@
 	force_sig(SIGSEGV);
 }
 
+#ifdef CONFIG_DYNAMIC_SIGFRAME
+#ifdef CONFIG_STRICT_SIGALTSTACK_SIZE
+static bool strict_sigaltstack_size __ro_after_init = true;
+#else
+static bool strict_sigaltstack_size __ro_after_init = false;
+#endif
+
+static int __init strict_sas_size(char *arg)
+{
+	return kstrtobool(arg, &strict_sigaltstack_size);
+}
+__setup("strict_sas_size", strict_sas_size);
+
+/*
+ * MINSIGSTKSZ is 2048 and can't be changed despite the fact that AVX512
+ * exceeds that size already. As such programs might never use the
+ * sigaltstack they just continued to work. While always checking against
+ * the real size would be correct, this might be considered a regression.
+ *
+ * Therefore avoid the sanity check, unless enforced by kernel
+ * configuration or command line option.
+ *
+ * When dynamic FPU features are supported, the check is also enforced when
+ * the task has permissions to use dynamic features. Tasks which have no
+ * permission are checked against the size of the non-dynamic feature set
+ * if strict checking is enabled. This avoids forcing all tasks on the
+ * system to allocate large sigaltstacks even if they are never going
+ * to use a dynamic feature. As this is serialized via sighand::siglock
+ * any permission request for a dynamic feature either happened already
+ * or will see the newly install sigaltstack size in the permission checks.
+ */
+bool sigaltstack_size_valid(size_t ss_size)
+{
+	unsigned long fsize = max_frame_size - fpu_default_state_size;
+	u64 mask;
+
+	lockdep_assert_held(&current->sighand->siglock);
+
+	if (!fpu_state_size_dynamic() && !strict_sigaltstack_size)
+		return true;
+
+	fsize += current->group_leader->thread.fpu.perm.__user_state_size;
+	if (likely(ss_size > fsize))
+		return true;
+
+	if (strict_sigaltstack_size)
+		return ss_size > fsize;
+
+	mask = current->group_leader->thread.fpu.perm.__state_perm;
+	if (mask & XFEATURE_MASK_USER_DYNAMIC)
+		return ss_size > fsize;
+
+	return true;
+}
+#endif /* CONFIG_DYNAMIC_SIGFRAME */
+
 #ifdef CONFIG_X86_X32_ABI
 COMPAT_SYSCALL_DEFINE0(x32_rt_sigreturn)
 {
@@ -929,7 +990,7 @@
 
 	set_current_blocked(&set);
 
-	if (restore_sigcontext(regs, &frame->uc.uc_mcontext, uc_flags))
+	if (!restore_sigcontext(regs, &frame->uc.uc_mcontext, uc_flags))
 		goto badframe;
 
 	if (compat_restore_altstack(&frame->uc.uc_stack))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/signal_compat.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/signal_compat.c
@@ -149,8 +149,10 @@
 
 	BUILD_BUG_ON(offsetof(siginfo_t, si_perf_data) != 0x18);
 	BUILD_BUG_ON(offsetof(siginfo_t, si_perf_type) != 0x20);
+	BUILD_BUG_ON(offsetof(siginfo_t, si_perf_flags) != 0x24);
 	BUILD_BUG_ON(offsetof(compat_siginfo_t, si_perf_data) != 0x10);
 	BUILD_BUG_ON(offsetof(compat_siginfo_t, si_perf_type) != 0x14);
+	BUILD_BUG_ON(offsetof(compat_siginfo_t, si_perf_flags) != 0x18);
 
 	CHECK_CSI_OFFSET(_sigpoll);
 	CHECK_CSI_SIZE  (_sigpoll, 2*sizeof(int));
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/smp.c
@@ -32,7 +32,7 @@
 #include <asm/mce.h>
 #include <asm/trace/irq_vectors.h>
 #include <asm/kexec.h>
-#include <asm/virtext.h>
+#include <asm/reboot.h>
 
 /*
  *	Some notes on x86 processor bugs affecting SMP operation:
@@ -122,7 +122,7 @@
 	if (raw_smp_processor_id() == atomic_read(&stopping_cpu))
 		return NMI_HANDLED;
 
-	cpu_emergency_vmxoff();
+	cpu_emergency_disable_virtualization();
 	stop_this_cpu(NULL);
 
 	return NMI_HANDLED;
@@ -134,7 +134,7 @@
 DEFINE_IDTENTRY_SYSVEC(sysvec_reboot)
 {
 	ack_APIC_irq();
-	cpu_emergency_vmxoff();
+	cpu_emergency_disable_virtualization();
 	stop_this_cpu(NULL);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/smpboot.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/smpboot.c
@@ -70,7 +70,7 @@
 #include <asm/mwait.h>
 #include <asm/apic.h>
 #include <asm/io_apic.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/setup.h>
 #include <asm/uv/uv.h>
 #include <linux/mc146818rtc.h>
@@ -105,6 +105,17 @@
 DEFINE_PER_CPU_READ_MOSTLY(struct cpuinfo_x86, cpu_info);
 EXPORT_PER_CPU_SYMBOL(cpu_info);
 
+struct mwait_cpu_dead {
+	unsigned int	control;
+	unsigned int	status;
+};
+
+/*
+ * Cache line aligned data for mwait_play_dead(). Separate on purpose so
+ * that it's unlikely to be touched by other CPUs.
+ */
+static DEFINE_PER_CPU_ALIGNED(struct mwait_cpu_dead, mwait_cpu_dead);
+
 /* Logical package management. We might want to allocate that dynamically */
 unsigned int __max_logical_packages __read_mostly;
 EXPORT_SYMBOL(__max_logical_packages);
@@ -1685,10 +1696,10 @@
  */
 static inline void mwait_play_dead(void)
 {
+	struct mwait_cpu_dead *md = this_cpu_ptr(&mwait_cpu_dead);
 	unsigned int eax, ebx, ecx, edx;
 	unsigned int highest_cstate = 0;
 	unsigned int highest_subcstate = 0;
-	void *mwait_ptr;
 	int i;
 
 	if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
@@ -1723,13 +1734,6 @@
 			(highest_subcstate - 1);
 	}
 
-	/*
-	 * This should be a memory location in a cache line which is
-	 * unlikely to be touched by other processors.  The actual
-	 * content is immaterial as it is not actually modified in any way.
-	 */
-	mwait_ptr = &current_thread_info()->flags;
-
 	wbinvd();
 
 	while (1) {
@@ -1741,9 +1745,9 @@
 		 * case where we return around the loop.
 		 */
 		mb();
-		clflush(mwait_ptr);
+		clflush(md);
 		mb();
-		__monitor(mwait_ptr, 0, 0);
+		__monitor(md, 0, 0);
 		mb();
 		__mwait(eax, 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/static_call.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/static_call.c
@@ -2,6 +2,7 @@
 #include <linux/static_call.h>
 #include <linux/memory.h>
 #include <linux/bug.h>
+#include <asm/sync_core.h>
 #include <asm/text-patching.h>
 
 enum insn_type {
@@ -9,19 +10,57 @@
 	NOP = 1,  /* site cond-call */
 	JMP = 2,  /* tramp / site tail-call */
 	RET = 3,  /* tramp / site cond-tail-call */
+	JCC = 4,
 };
 
 /*
- * data16 data16 xorq %rax, %rax - a single 5 byte instruction that clears %rax
- * The REX.W cancels the effect of any data16.
+ * ud1 %esp, %ecx - a 3 byte #UD that is unique to trampolines, chosen such
+ * that there is no false-positive trampoline identification while also being a
+ * speculation stop.
  */
-static const u8 xor5rax[] = { 0x66, 0x66, 0x48, 0x31, 0xc0 };
+static const u8 tramp_ud[] = { 0x0f, 0xb9, 0xcc };
 
-static void __ref __static_call_transform(void *insn, enum insn_type type, void *func)
+/*
+ * cs cs cs xorl %eax, %eax - a single 5 byte instruction that clears %[er]ax
+ */
+static const u8 xor5rax[] = { 0x2e, 0x2e, 0x2e, 0x31, 0xc0 };
+
+static const u8 retinsn[] = { RET_INSN_OPCODE, 0xcc, 0xcc, 0xcc, 0xcc };
+
+static u8 __is_Jcc(u8 *insn) /* Jcc.d32 */
+{
+	u8 ret = 0;
+
+	if (insn[0] == 0x0f) {
+		u8 tmp = insn[1];
+		if ((tmp & 0xf0) == 0x80)
+			ret = tmp;
+	}
+
+	return ret;
+}
+
+extern void __static_call_return(void);
+
+asm (".global __static_call_return\n\t"
+     ".type __static_call_return, @function\n\t"
+     ASM_FUNC_ALIGN "\n\t"
+     "__static_call_return:\n\t"
+     ANNOTATE_NOENDBR
+     ANNOTATE_RETPOLINE_SAFE
+     "ret; int3\n\t"
+     ".size __static_call_return, . - __static_call_return \n\t");
+
+static void __ref __static_call_transform(void *insn, enum insn_type type,
+					  void *func, bool modinit)
 {
 	const void *emulate = NULL;
 	int size = CALL_INSN_SIZE;
 	const void *code;
+	u8 op, buf[6];
+
+	if ((type == JMP || type == RET) && (op = __is_Jcc(insn)))
+		type = JCC;
 
 	switch (type) {
 	case CALL:
@@ -42,27 +81,44 @@
 		break;
 
 	case RET:
-		code = text_gen_insn(RET_INSN_OPCODE, insn, func);
-		size = RET_INSN_SIZE;
+		if (cpu_feature_enabled(X86_FEATURE_RETHUNK))
+			code = text_gen_insn(JMP32_INSN_OPCODE, insn, x86_return_thunk);
+		else
+			code = &retinsn;
+		break;
+
+	case JCC:
+		if (!func) {
+			func = __static_call_return;
+			if (cpu_feature_enabled(X86_FEATURE_RETHUNK))
+				func = x86_return_thunk;
+		}
+
+		buf[0] = 0x0f;
+		__text_gen_insn(buf+1, op, insn+1, func, 5);
+		code = buf;
+		size = 6;
+
 		break;
 	}
 
 	if (memcmp(insn, code, size) == 0)
 		return;
 
-	if (unlikely(system_state == SYSTEM_BOOTING))
+	if (system_state == SYSTEM_BOOTING || modinit)
 		return text_poke_early(insn, code, size);
 
 	text_poke_bp(insn, code, size, emulate);
 }
 
-static void __static_call_validate(void *insn, bool tail)
+static void __static_call_validate(u8 *insn, bool tail)
 {
-	u8 opcode = *(u8 *)insn;
+	u8 opcode = insn[0];
 
 	if (tail) {
 		if (opcode == JMP32_INSN_OPCODE ||
-		    opcode == RET_INSN_OPCODE)
+		    opcode == RET_INSN_OPCODE ||
+		    __is_Jcc(insn))
 			return;
 	} else {
 		if (opcode == CALL_INSN_OPCODE ||
@@ -98,14 +154,63 @@
 
 	if (tramp) {
 		__static_call_validate(tramp, true);
-		__static_call_transform(tramp, __sc_insn(!func, true), func);
+		__static_call_transform(tramp, __sc_insn(!func, true), func, false);
 	}
 
 	if (IS_ENABLED(CONFIG_HAVE_STATIC_CALL_INLINE) && site) {
 		__static_call_validate(site, tail);
-		__static_call_transform(site, __sc_insn(!func, tail), func);
+		__static_call_transform(site, __sc_insn(!func, tail), func, false);
 	}
 
 	mutex_unlock(&text_mutex);
 }
 EXPORT_SYMBOL_GPL(arch_static_call_transform);
+
+noinstr void __static_call_update_early(void *tramp, void *func)
+{
+	BUG_ON(system_state != SYSTEM_BOOTING);
+	BUG_ON(static_call_initialized);
+	__text_gen_insn(tramp, JMP32_INSN_OPCODE, tramp, func, JMP32_INSN_SIZE);
+	sync_core();
+}
+
+#ifdef CONFIG_RETHUNK
+/*
+ * This is called by apply_returns() to fix up static call trampolines,
+ * specifically ARCH_DEFINE_STATIC_CALL_NULL_TRAMP which is recorded as
+ * having a return trampoline.
+ *
+ * The problem is that static_call() is available before determining
+ * X86_FEATURE_RETHUNK and, by implication, running alternatives.
+ *
+ * This means that __static_call_transform() above can have overwritten the
+ * return trampoline and we now need to fix things up to be consistent.
+ */
+bool __static_call_fixup(void *tramp, u8 op, void *dest)
+{
+	unsigned long addr = (unsigned long)tramp;
+	/*
+	 * Not all .return_sites are a static_call trampoline (most are not).
+	 * Check if the 3 bytes after the return are still kernel text, if not,
+	 * then this definitely is not a trampoline and we need not worry
+	 * further.
+	 *
+	 * This avoids the memcmp() below tripping over pagefaults etc..
+	 */
+	if (((addr >> PAGE_SHIFT) != ((addr + 7) >> PAGE_SHIFT)) &&
+	    !kernel_text_address(addr + 7))
+		return false;
+
+	if (memcmp(tramp+5, tramp_ud, 3)) {
+		/* Not a trampoline site, not our problem. */
+		return false;
+	}
+
+	mutex_lock(&text_mutex);
+	if (op == RET_INSN_OPCODE || dest == &__x86_return_thunk)
+		__static_call_transform(tramp, RET, NULL, true);
+	mutex_unlock(&text_mutex);
+
+	return true;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/step.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/step.c
@@ -180,8 +180,7 @@
 	 *
 	 * NOTE: this means that set/clear TIF_BLOCKSTEP is only safe if
 	 * task is current or it can't be running, otherwise we can race
-	 * with __switch_to_xtra(). We rely on ptrace_freeze_traced() but
-	 * PTRACE_KILL is not safe.
+	 * with __switch_to_xtra(). We rely on ptrace_freeze_traced().
 	 */
 	local_irq_disable();
 	debugctl = get_debugctlmsr();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/sys_x86_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/sys_x86_64.c
@@ -68,9 +68,6 @@
 	if (*str == 0)
 		return 1;
 
-	if (*str == '=')
-		str++;
-
 	if (!strcmp(str, "32"))
 		va_align.flags = ALIGN_VA_32;
 	else if (!strcmp(str, "64"))
@@ -80,11 +77,11 @@
 	else if (!strcmp(str, "on"))
 		va_align.flags = ALIGN_VA_32 | ALIGN_VA_64;
 	else
-		return 0;
+		pr_warn("invalid option value: 'align_va_addr=%s'\n", str);
 
 	return 1;
 }
-__setup("align_va_addr", control_va_addr_alignment);
+__setup("align_va_addr=", control_va_addr_alignment);
 
 SYSCALL_DEFINE6(mmap, unsigned long, addr, unsigned long, len,
 		unsigned long, prot, unsigned long, flags,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/time.c
@@ -27,25 +27,7 @@
 
 unsigned long profile_pc(struct pt_regs *regs)
 {
-	unsigned long pc = instruction_pointer(regs);
-
-	if (!user_mode(regs) && in_lock_functions(pc)) {
-#ifdef CONFIG_FRAME_POINTER
-		return *(unsigned long *)(regs->bp + sizeof(long));
-#else
-		unsigned long *sp = (unsigned long *)regs->sp;
-		/*
-		 * Return address is either directly at stack pointer
-		 * or above a saved flags. Eflags has bits 22-31 zero,
-		 * kernel addresses don't.
-		 */
-		if (sp[0] >> 22)
-			return sp[0];
-		if (sp[1] >> 22)
-			return sp[1];
-#endif
-	}
-	return pc;
+	return instruction_pointer(regs);
 }
 EXPORT_SYMBOL(profile_pc);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/traps.c
@@ -48,7 +48,7 @@
 #include <asm/ftrace.h>
 #include <asm/traps.h>
 #include <asm/desc.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/cpu.h>
 #include <asm/cpu_entry_area.h>
 #include <asm/mce.h>
@@ -313,17 +313,19 @@
 }
 
 #ifdef CONFIG_VMAP_STACK
-__visible void __noreturn handle_stack_overflow(const char *message,
-						struct pt_regs *regs,
-						unsigned long fault_address)
-{
-	printk(KERN_EMERG "BUG: stack guard page was hit at %p (stack is %p..%p)\n",
-		 (void *)fault_address, current->stack,
-		 (char *)current->stack + THREAD_SIZE - 1);
-	die(message, regs, 0);
+__visible void __noreturn handle_stack_overflow(struct pt_regs *regs,
+						unsigned long fault_address,
+						struct stack_info *info)
+{
+	const char *name = stack_type_name(info->type);
+
+	printk(KERN_EMERG "BUG: %s stack guard page was hit at %p (stack is %p..%p)\n",
+	       name, (void *)fault_address, info->begin, info->end);
+
+	die("stack guard page", regs, 0);
 
 	/* Be absolutely certain we don't return. */
-	panic("%s", message);
+	panic("%s stack guard hit", name);
 }
 #endif
 
@@ -353,6 +355,7 @@
 
 #ifdef CONFIG_VMAP_STACK
 	unsigned long address = read_cr2();
+	struct stack_info info;
 #endif
 
 #ifdef CONFIG_X86_ESPFIX64
@@ -455,10 +458,8 @@
 	 * stack even if the actual trigger for the double fault was
 	 * something else.
 	 */
-	if ((unsigned long)task_stack_page(tsk) - 1 - address < PAGE_SIZE) {
-		handle_stack_overflow("kernel stack overflow (double-fault)",
-				      regs, address);
-	}
+	if (get_stack_guard_info((void *)address, &info))
+		handle_stack_overflow(regs, address, &info);
 #endif
 
 	pr_emerg("PANIC: double fault, error_code: 0x%lx\n", error_code);
@@ -528,6 +529,36 @@
 
 #define GPFSTR "general protection fault"
 
+static bool fixup_iopl_exception(struct pt_regs *regs)
+{
+	struct thread_struct *t = &current->thread;
+	unsigned char byte;
+	unsigned long ip;
+
+	if (!IS_ENABLED(CONFIG_X86_IOPL_IOPERM) || t->iopl_emul != 3)
+		return false;
+
+	if (insn_get_effective_ip(regs, &ip))
+		return false;
+
+	if (get_user(byte, (const char __user *)ip))
+		return false;
+
+	if (byte != 0xfa && byte != 0xfb)
+		return false;
+
+	if (!t->iopl_warn && printk_ratelimit()) {
+		pr_err("%s[%d] attempts to use CLI/STI, pretending it's a NOP, ip:%lx",
+		       current->comm, task_pid_nr(current), ip);
+		print_vma_addr(KERN_CONT " in ", ip);
+		pr_cont("\n");
+		t->iopl_warn = 1;
+	}
+
+	regs->ip += 1;
+	return true;
+}
+
 DEFINE_IDTENTRY_ERRORCODE(exc_general_protection)
 {
 	char desc[sizeof(GPFSTR) + 50 + 2*sizeof(unsigned long) + 1] = GPFSTR;
@@ -553,6 +584,9 @@
 	tsk = current;
 
 	if (user_mode(regs)) {
+		if (fixup_iopl_exception(regs))
+			goto exit;
+
 		tsk->thread.error_code = error_code;
 		tsk->thread.trap_nr = X86_TRAP_GP;
 
@@ -625,6 +659,7 @@
 
 	return res == NOTIFY_STOP;
 }
+NOKPROBE_SYMBOL(do_int3);
 
 static void do_int3_user(struct pt_regs *regs)
 {
@@ -709,7 +744,7 @@
 	stack = (unsigned long *)sp;
 
 	if (!get_stack_info_noinstr(stack, current, &info) || info.type == STACK_TYPE_ENTRY ||
-	    info.type >= STACK_TYPE_EXCEPTION_LAST)
+	    info.type > STACK_TYPE_EXCEPTION_LAST)
 		sp = __this_cpu_ist_top_va(VC2);
 
 sync:
@@ -727,14 +762,10 @@
 }
 #endif
 
-struct bad_iret_stack {
-	void *error_entry_ret;
-	struct pt_regs regs;
-};
-
-asmlinkage __visible noinstr
-struct bad_iret_stack *fixup_bad_iret(struct bad_iret_stack *s)
+asmlinkage __visible noinstr struct pt_regs *fixup_bad_iret(struct pt_regs *bad_regs)
 {
+	struct pt_regs tmp, *new_stack;
+
 	/*
 	 * This is called from entry_64.S early in handling a fault
 	 * caused by a bad iret to user mode.  To handle the fault
@@ -743,19 +774,18 @@
 	 * just below the IRET frame) and we want to pretend that the
 	 * exception came from the IRET target.
 	 */
-	struct bad_iret_stack tmp, *new_stack =
-		(struct bad_iret_stack *)__this_cpu_read(cpu_tss_rw.x86_tss.sp0) - 1;
+	new_stack = (struct pt_regs *)__this_cpu_read(cpu_tss_rw.x86_tss.sp0) - 1;
 
 	/* Copy the IRET target to the temporary storage. */
-	__memcpy(&tmp.regs.ip, (void *)s->regs.sp, 5*8);
+	__memcpy(&tmp.ip, (void *)bad_regs->sp, 5*8);
 
 	/* Copy the remainder of the stack from the current stack. */
-	__memcpy(&tmp, s, offsetof(struct bad_iret_stack, regs.ip));
+	__memcpy(&tmp, bad_regs, offsetof(struct pt_regs, ip));
 
 	/* Update the entry stack */
 	__memcpy(new_stack, &tmp, sizeof(tmp));
 
-	BUG_ON(!user_mode(&new_stack->regs));
+	BUG_ON(!user_mode(new_stack));
 	return new_stack;
 }
 #endif
@@ -1108,10 +1138,48 @@
 	 */
 }
 
+static bool handle_xfd_event(struct pt_regs *regs)
+{
+	u64 xfd_err;
+	int err;
+
+	if (!IS_ENABLED(CONFIG_X86_64) || !cpu_feature_enabled(X86_FEATURE_XFD))
+		return false;
+
+	rdmsrl(MSR_IA32_XFD_ERR, xfd_err);
+	if (!xfd_err)
+		return false;
+
+	wrmsrl(MSR_IA32_XFD_ERR, 0);
+
+	/* Die if that happens in kernel space */
+	if (WARN_ON(!user_mode(regs)))
+		return false;
+
+	local_irq_enable();
+
+	err = xfd_enable_feature(xfd_err);
+
+	switch (err) {
+	case -EPERM:
+		force_sig_fault(SIGILL, ILL_ILLOPC, error_get_trap_addr(regs));
+		break;
+	case -EFAULT:
+		force_sig(SIGSEGV);
+		break;
+	}
+
+	local_irq_disable();
+	return true;
+}
+
 DEFINE_IDTENTRY(exc_device_not_available)
 {
 	unsigned long cr0 = read_cr0();
 
+	if (handle_xfd_event(regs))
+		return;
+
 #ifdef CONFIG_MATH_EMULATION
 	if (!boot_cpu_has(X86_FEATURE_FPU) && (cr0 & X86_CR0_EM)) {
 		struct math_emu_info info = { };
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/tsc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/tsc.c
@@ -920,7 +920,7 @@
 
 void tsc_save_sched_clock_state(void)
 {
-	if (!sched_clock_stable())
+	if (!static_branch_likely(&__use_tsc) && !sched_clock_stable())
 		return;
 
 	cyc2ns_suspend = sched_clock();
@@ -940,7 +940,7 @@
 	unsigned long flags;
 	int cpu;
 
-	if (!sched_clock_stable())
+	if (!static_branch_likely(&__use_tsc) && !sched_clock_stable())
 		return;
 
 	local_irq_save(flags);
@@ -1180,6 +1180,12 @@
 
 EXPORT_SYMBOL_GPL(mark_tsc_unstable);
 
+static void __init tsc_disable_clocksource_watchdog(void)
+{
+	clocksource_tsc_early.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
+	clocksource_tsc.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
+}
+
 static void __init check_system_tsc_reliable(void)
 {
 #if defined(CONFIG_MGEODEGX1) || defined(CONFIG_MGEODE_LX) || defined(CONFIG_X86_GENERIC)
@@ -1196,6 +1202,23 @@
 #endif
 	if (boot_cpu_has(X86_FEATURE_TSC_RELIABLE))
 		tsc_clocksource_reliable = 1;
+
+	/*
+	 * Disable the clocksource watchdog when the system has:
+	 *  - TSC running at constant frequency
+	 *  - TSC which does not stop in C-States
+	 *  - the TSC_ADJUST register which allows to detect even minimal
+	 *    modifications
+	 *  - not more than two sockets. As the number of sockets cannot be
+	 *    evaluated at the early boot stage where this has to be
+	 *    invoked, check the number of online memory nodes as a
+	 *    fallback solution which is an reasonable estimate.
+	 */
+	if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC) &&
+	    boot_cpu_has(X86_FEATURE_NONSTOP_TSC) &&
+	    boot_cpu_has(X86_FEATURE_TSC_ADJUST) &&
+	    nr_online_nodes <= 4)
+		tsc_disable_clocksource_watchdog();
 }
 
 /*
@@ -1387,9 +1410,6 @@
 	if (tsc_unstable)
 		goto unreg;
 
-	if (tsc_clocksource_reliable || no_tsc_watchdog)
-		clocksource_tsc.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
-
 	if (boot_cpu_has(X86_FEATURE_NONSTOP_TSC_S3))
 		clocksource_tsc.flags |= CLOCK_SOURCE_SUSPEND_NONSTOP;
 
@@ -1527,7 +1547,7 @@
 	}
 
 	if (tsc_clocksource_reliable || no_tsc_watchdog)
-		clocksource_tsc_early.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
+		tsc_disable_clocksource_watchdog();
 
 	clocksource_register_khz(&clocksource_tsc_early, tsc_khz);
 	detect_art();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/tsc_sync.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/tsc_sync.c
@@ -30,6 +30,7 @@
 };
 
 static DEFINE_PER_CPU(struct tsc_adjust, tsc_adjust);
+static struct timer_list tsc_sync_check_timer;
 
 /*
  * TSC's on different sockets may be reset asynchronously.
@@ -77,6 +78,46 @@
 	}
 }
 
+/*
+ * Normally the tsc_sync will be checked every time system enters idle
+ * state, but there is still caveat that a system won't enter idle,
+ * either because it's too busy or configured purposely to not enter
+ * idle.
+ *
+ * So setup a periodic timer (every 10 minutes) to make sure the check
+ * is always on.
+ */
+
+#define SYNC_CHECK_INTERVAL		(HZ * 600)
+
+static void tsc_sync_check_timer_fn(struct timer_list *unused)
+{
+	int next_cpu;
+
+	tsc_verify_tsc_adjust(false);
+
+	/* Run the check for all onlined CPUs in turn */
+	next_cpu = cpumask_next(raw_smp_processor_id(), cpu_online_mask);
+	if (next_cpu >= nr_cpu_ids)
+		next_cpu = cpumask_first(cpu_online_mask);
+
+	tsc_sync_check_timer.expires += SYNC_CHECK_INTERVAL;
+	add_timer_on(&tsc_sync_check_timer, next_cpu);
+}
+
+static int __init start_sync_check_timer(void)
+{
+	if (!cpu_feature_enabled(X86_FEATURE_TSC_ADJUST) || tsc_clocksource_reliable)
+		return 0;
+
+	timer_setup(&tsc_sync_check_timer, tsc_sync_check_timer_fn, 0);
+	tsc_sync_check_timer.expires = jiffies + SYNC_CHECK_INTERVAL;
+	add_timer(&tsc_sync_check_timer);
+
+	return 0;
+}
+late_initcall(start_sync_check_timer);
+
 static void tsc_sanitize_first_cpu(struct tsc_adjust *cur, s64 bootval,
 				   unsigned int cpu, bool bootcpu)
 {
@@ -151,11 +192,9 @@
 	cur->warned = false;
 
 	/*
-	 * If a non-zero TSC value for socket 0 may be valid then the default
-	 * adjusted value cannot assumed to be zero either.
+	 * The default adjust value cannot be assumed to be zero on any socket.
 	 */
-	if (tsc_async_resets)
-		cur->adjusted = bootval;
+	cur->adjusted = bootval;
 
 	/*
 	 * Check whether this CPU is the first in a package to come up. In
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/unwind_orc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/unwind_orc.c
@@ -93,22 +93,27 @@
 static struct orc_entry *orc_ftrace_find(unsigned long ip)
 {
 	struct ftrace_ops *ops;
-	unsigned long caller;
+	unsigned long tramp_addr, offset;
 
 	ops = ftrace_ops_trampoline(ip);
 	if (!ops)
 		return NULL;
 
+	/* Set tramp_addr to the start of the code copied by the trampoline */
 	if (ops->flags & FTRACE_OPS_FL_SAVE_REGS)
-		caller = (unsigned long)ftrace_regs_call;
+		tramp_addr = (unsigned long)ftrace_regs_caller;
 	else
-		caller = (unsigned long)ftrace_call;
+		tramp_addr = (unsigned long)ftrace_caller;
+
+	/* Now place tramp_addr to the location within the trampoline ip is at */
+	offset = ip - ops->trampoline;
+	tramp_addr += offset;
 
 	/* Prevent unlikely recursion */
-	if (ip == caller)
+	if (ip == tramp_addr)
 		return NULL;
 
-	return orc_find(caller);
+	return orc_find(tramp_addr);
 }
 #else
 static struct orc_entry *orc_ftrace_find(unsigned long ip)
@@ -695,7 +700,7 @@
 	/* Otherwise, skip ahead to the user-specified starting frame: */
 	while (!unwind_done(state) &&
 	       (!on_stack(&state->stack_info, first_frame, sizeof(long)) ||
-			state->sp < (unsigned long)first_frame))
+			state->sp <= (unsigned long)first_frame))
 		unwind_next_frame(state);
 
 	return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/uprobes.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/uprobes.c
@@ -722,8 +722,9 @@
 	switch (opc1) {
 	case 0xeb:	/* jmp 8 */
 	case 0xe9:	/* jmp 32 */
-	case 0x90:	/* prefix* + nop; same as jmp with .offs = 0 */
 		break;
+	case 0x90:	/* prefix* + nop; same as jmp with .offs = 0 */
+		goto setup;
 
 	case 0xe8:	/* call relative */
 		branch_clear_offset(auprobe, insn);
@@ -753,6 +754,7 @@
 			return -ENOTSUPP;
 	}
 
+setup:
 	auprobe->branch.opc1 = opc1;
 	auprobe->branch.ilen = insn->length;
 	auprobe->branch.offs = insn->immediate.value;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/verify_cpu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/verify_cpu.S
@@ -132,9 +132,9 @@
 .Lverify_cpu_no_longmode:
 	popf				# Restore caller passed flags
 	movl $1,%eax
-	ret
+	RET
 .Lverify_cpu_sse_ok:
 	popf				# Restore caller passed flags
 	xorl %eax, %eax
-	ret
+	RET
 SYM_FUNC_END(verify_cpu)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/vm86_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/vm86_32.c
@@ -142,6 +142,7 @@
 
 	user_access_end();
 
+exit_vm86:
 	preempt_disable();
 	tsk->thread.sp0 = vm86->saved_sp0;
 	tsk->thread.sysenter_cs = __KERNEL_CS;
@@ -161,7 +162,8 @@
 	user_access_end();
 Efault:
 	pr_alert("could not access userspace vm86 info\n");
-	do_exit(SIGSEGV);
+	force_exit_sig(SIGSEGV);
+	goto exit_vm86;
 }
 
 static int do_vm86_irq_handling(int subfunction, int irqnumber);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/vmlinux.lds.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/vmlinux.lds.S
@@ -133,7 +133,20 @@
 		LOCK_TEXT
 		KPROBES_TEXT
 		ALIGN_ENTRY_TEXT_BEGIN
+#ifdef CONFIG_CPU_SRSO
+		*(.text..__x86.rethunk_untrain)
+#endif
+
 		ENTRY_TEXT
+
+#ifdef CONFIG_CPU_SRSO
+		/*
+		 * See the comment above srso_alias_untrain_ret()'s
+		 * definition.
+		 */
+		. = srso_alias_untrain_ret | (1 << 2) | (1 << 8) | (1 << 14) | (1 << 20);
+		*(.text..__x86.rethunk_safe)
+#endif
 		ALIGN_ENTRY_TEXT_END
 		SOFTIRQENTRY_TEXT
 		STATIC_CALL_TEXT
@@ -142,13 +155,15 @@
 
 #ifdef CONFIG_RETPOLINE
 		__indirect_thunk_start = .;
-		*(.text.__x86.indirect_thunk)
+		*(.text..__x86.indirect_thunk)
+		*(.text..__x86.return_thunk)
 		__indirect_thunk_end = .;
 #endif
 	} :text =0xcccc
 
 	/* End of text section, which should occupy whole number of pages */
 	_etext = .;
+
 	. = ALIGN(PAGE_SIZE);
 
 	X86_ALIGN_RODATA_BEGIN
@@ -272,6 +287,27 @@
 		__parainstructions_end = .;
 	}
 
+#ifdef CONFIG_RETPOLINE
+	/*
+	 * List of instructions that call/jmp/jcc to retpoline thunks
+	 * __x86_indirect_thunk_*(). These instructions can be patched along
+	 * with alternatives, after which the section can be freed.
+	 */
+	. = ALIGN(8);
+	.retpoline_sites : AT(ADDR(.retpoline_sites) - LOAD_OFFSET) {
+		__retpoline_sites = .;
+		*(.retpoline_sites)
+		__retpoline_sites_end = .;
+	}
+
+	. = ALIGN(8);
+	.return_sites : AT(ADDR(.return_sites) - LOAD_OFFSET) {
+		__return_sites = .;
+		*(.return_sites)
+		__return_sites_end = .;
+	}
+#endif
+
 	/*
 	 * struct alt_inst entries. From the header (alternative.h):
 	 * "Alternative instructions for different CPU types or capabilities"
@@ -378,7 +414,7 @@
 	.brk : AT(ADDR(.brk) - LOAD_OFFSET) {
 		__brk_base = .;
 		. += 64 * 1024;		/* 64k alignment slop space */
-		*(.brk_reservation)	/* areas brk users have reserved */
+		*(.bss..brk)		/* areas brk users have reserved */
 		__brk_limit = .;
 	}
 
@@ -475,6 +511,27 @@
            "fixed_percpu_data is not at start of per-cpu area");
 #endif
 
+#ifdef CONFIG_RETHUNK
+. = ASSERT((retbleed_return_thunk & 0x3f) == 0, "retbleed_return_thunk not cacheline-aligned");
+. = ASSERT((srso_safe_ret & 0x3f) == 0, "srso_safe_ret not cacheline-aligned");
+#endif
+
+#ifdef CONFIG_CPU_SRSO
+/*
+ * GNU ld cannot do XOR until 2.41.
+ * https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=f6f78318fca803c4907fb8d7f6ded8295f1947b1
+ *
+ * LLVM lld cannot do XOR until lld-17.
+ * https://github.com/llvm/llvm-project/commit/fae96104d4378166cbe5c875ef8ed808a356f3fb
+ *
+ * Instead do: (A | B) - (A & B) in order to compute the XOR
+ * of the two function addresses:
+ */
+. = ASSERT(((ABSOLUTE(srso_alias_untrain_ret) | srso_alias_safe_ret) -
+		(ABSOLUTE(srso_alias_untrain_ret) & srso_alias_safe_ret)) == ((1 << 2) | (1 << 8) | (1 << 14) | (1 << 20)),
+		"SRSO function pair won't alias");
+#endif
+
 #endif /* CONFIG_X86_64 */
 
 #ifdef CONFIG_KEXEC_CORE
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kernel/x86_init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kernel/x86_init.c
@@ -32,8 +32,8 @@
 static void iommu_shutdown_noop(void) { }
 bool __init bool_x86_init_noop(void) { return false; }
 void x86_op_int_noop(int cpu) { }
-static __init int set_rtc_noop(const struct timespec64 *now) { return -EINVAL; }
-static __init void get_rtc_noop(struct timespec64 *now) { }
+static int set_rtc_noop(const struct timespec64 *now) { return -EINVAL; }
+static void get_rtc_noop(struct timespec64 *now) { }
 
 static __initconst const struct of_device_id of_cmos_match[] = {
 	{ .compatible = "motorola,mc146818" },
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/cpuid.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/cpuid.c
@@ -32,6 +32,26 @@
 u32 kvm_cpu_caps[NR_KVM_CPU_CAPS] __read_mostly;
 EXPORT_SYMBOL_GPL(kvm_cpu_caps);
 
+struct cpuid_xstate_sizes {
+	u32 eax;
+	u32 ebx;
+	u32 ecx;
+};
+
+static struct cpuid_xstate_sizes xstate_sizes[XFEATURE_MAX] __ro_after_init;
+
+void __init kvm_init_xstate_sizes(void)
+{
+	u32 ign;
+	int i;
+
+	for (i = XFEATURE_YMM; i < ARRAY_SIZE(xstate_sizes); i++) {
+		struct cpuid_xstate_sizes *xs = &xstate_sizes[i];
+
+		cpuid_count(0xD, i, &xs->eax, &xs->ebx, &xs->ecx, &ign);
+	}
+}
+
 static u32 xstate_required_size(u64 xstate_bv, bool compacted)
 {
 	int feature_bit = 0;
@@ -40,10 +60,15 @@
 	xstate_bv &= XFEATURE_MASK_EXTEND;
 	while (xstate_bv) {
 		if (xstate_bv & 0x1) {
-		        u32 eax, ebx, ecx, edx, offset;
-		        cpuid_count(0xD, feature_bit, &eax, &ebx, &ecx, &edx);
-			offset = compacted ? ret : ebx;
-			ret = max(ret, offset + eax);
+			struct cpuid_xstate_sizes *xs = &xstate_sizes[feature_bit];
+			u32 offset;
+
+			/* ECX[1]: 64B alignment in compacted form */
+			if (compacted)
+				offset = (xs->ecx & 0x2) ? ALIGN(ret, 64) : ret;
+			else
+				offset = xs->ebx;
+			ret = max(ret, offset + xs->eax);
 		}
 
 		xstate_bv >>= 1;
@@ -189,6 +214,7 @@
 
 	kvm_update_pv_runtime(vcpu);
 
+	vcpu->arch.is_amd_compatible = guest_cpuid_is_amd_or_hygon(vcpu);
 	vcpu->arch.maxphyaddr = cpuid_query_maxphyaddr(vcpu);
 	vcpu->arch.reserved_gpa_bits = kvm_vcpu_reserved_gpa_bits_raw(vcpu);
 
@@ -232,6 +258,25 @@
 	return rsvd_bits(cpuid_maxphyaddr(vcpu), 63);
 }
 
+static int kvm_set_cpuid(struct kvm_vcpu *vcpu, struct kvm_cpuid_entry2 *e2,
+                        int nent)
+{
+    int r;
+
+    r = kvm_check_cpuid(e2, nent);
+    if (r)
+        return r;
+
+    kvfree(vcpu->arch.cpuid_entries);
+    vcpu->arch.cpuid_entries = e2;
+    vcpu->arch.cpuid_nent = nent;
+
+    kvm_update_cpuid_runtime(vcpu);
+    kvm_vcpu_after_set_cpuid(vcpu);
+
+    return 0;
+}
+
 /* when an old userspace process fills a new kernel module */
 int kvm_vcpu_ioctl_set_cpuid(struct kvm_vcpu *vcpu,
 			     struct kvm_cpuid *cpuid,
@@ -268,18 +313,9 @@
 		e2[i].padding[2] = 0;
 	}
 
-	r = kvm_check_cpuid(e2, cpuid->nent);
-	if (r) {
+	r = kvm_set_cpuid(vcpu, e2, cpuid->nent);
+	if (r)
 		kvfree(e2);
-		goto out_free_cpuid;
-	}
-
-	kvfree(vcpu->arch.cpuid_entries);
-	vcpu->arch.cpuid_entries = e2;
-	vcpu->arch.cpuid_nent = cpuid->nent;
-
-	kvm_update_cpuid_runtime(vcpu);
-	kvm_vcpu_after_set_cpuid(vcpu);
 
 out_free_cpuid:
 	kvfree(e);
@@ -303,20 +339,11 @@
 			return PTR_ERR(e2);
 	}
 
-	r = kvm_check_cpuid(e2, cpuid->nent);
-	if (r) {
+	r = kvm_set_cpuid(vcpu, e2, cpuid->nent);
+	if (r)
 		kvfree(e2);
-		return r;
-	}
-
-	kvfree(vcpu->arch.cpuid_entries);
-	vcpu->arch.cpuid_entries = e2;
-	vcpu->arch.cpuid_nent = cpuid->nent;
 
-	kvm_update_cpuid_runtime(vcpu);
-	kvm_vcpu_after_set_cpuid(vcpu);
-
-	return 0;
+	return r;
 }
 
 int kvm_vcpu_ioctl_get_cpuid2(struct kvm_vcpu *vcpu,
@@ -354,9 +381,9 @@
 }
 
 static __always_inline
-void kvm_cpu_cap_init_scattered(enum kvm_only_cpuid_leafs leaf, u32 mask)
+void kvm_cpu_cap_init_kvm_defined(enum kvm_only_cpuid_leafs leaf, u32 mask)
 {
-	/* Use kvm_cpu_cap_mask for non-scattered leafs. */
+	/* Use kvm_cpu_cap_mask for leafs that aren't KVM-only. */
 	BUILD_BUG_ON(leaf < NCAPINTS);
 
 	kvm_cpu_caps[leaf] = mask;
@@ -366,7 +393,7 @@
 
 static __always_inline void kvm_cpu_cap_mask(enum cpuid_leafs leaf, u32 mask)
 {
-	/* Use kvm_cpu_cap_init_scattered for scattered leafs. */
+	/* Use kvm_cpu_cap_init_kvm_defined for KVM-only leafs. */
 	BUILD_BUG_ON(leaf >= NCAPINTS);
 
 	kvm_cpu_caps[leaf] &= mask;
@@ -420,12 +447,13 @@
 	);
 
 	kvm_cpu_cap_mask(CPUID_7_0_EBX,
-		F(FSGSBASE) | F(SGX) | F(BMI1) | F(HLE) | F(AVX2) | F(SMEP) |
-		F(BMI2) | F(ERMS) | F(INVPCID) | F(RTM) | 0 /*MPX*/ | F(RDSEED) |
-		F(ADX) | F(SMAP) | F(AVX512IFMA) | F(AVX512F) | F(AVX512PF) |
-		F(AVX512ER) | F(AVX512CD) | F(CLFLUSHOPT) | F(CLWB) | F(AVX512DQ) |
-		F(SHA_NI) | F(AVX512BW) | F(AVX512VL) | 0 /*INTEL_PT*/
-	);
+		F(FSGSBASE) | F(SGX) | F(BMI1) | F(HLE) | F(AVX2) |
+		F(FDP_EXCPTN_ONLY) | F(SMEP) | F(BMI2) | F(ERMS) | F(INVPCID) |
+		F(RTM) | F(ZERO_FCS_FDS) | 0 /*MPX*/ | F(AVX512F) |
+		F(AVX512DQ) | F(RDSEED) | F(ADX) | F(SMAP) | F(AVX512IFMA) |
+		F(CLFLUSHOPT) | F(CLWB) | 0 /*INTEL_PT*/ | F(AVX512PF) |
+		F(AVX512ER) | F(AVX512CD) | F(SHA_NI) | F(AVX512BW) |
+		F(AVX512VL));
 
 	kvm_cpu_cap_mask(CPUID_7_ECX,
 		F(AVX512VBMI) | F(LA57) | F(PKU) | 0 /*OSPKE*/ | F(RDPID) |
@@ -467,11 +495,16 @@
 		F(AVX_VNNI) | F(AVX512_BF16)
 	);
 
+	kvm_cpu_cap_init_kvm_defined(CPUID_7_2_EDX,
+		F(INTEL_PSFD) | F(IPRED_CTRL) | F(RRSBA_CTRL) | F(DDPD_U) |
+		F(BHI_CTRL) | F(MCDT_NO)
+	);
+
 	kvm_cpu_cap_mask(CPUID_D_1_EAX,
 		F(XSAVEOPT) | F(XSAVEC) | F(XGETBV1) | F(XSAVES)
 	);
 
-	kvm_cpu_cap_init_scattered(CPUID_12_EAX,
+	kvm_cpu_cap_init_kvm_defined(CPUID_12_EAX,
 		SF(SGX1) | SF(SGX2)
 	);
 
@@ -542,6 +575,9 @@
 		F(PMM) | F(PMM_EN)
 	);
 
+	if (cpu_feature_enabled(X86_FEATURE_SRSO_NO))
+		kvm_cpu_cap_set(X86_FEATURE_SRSO_NO);
+
 	/*
 	 * Hide RDTSCP and RDPID if either feature is reported as supported but
 	 * probing MSR_TSC_AUX failed.  This is purely a sanity check and
@@ -565,16 +601,22 @@
 	int nent;
 };
 
+static struct kvm_cpuid_entry2 *get_next_cpuid(struct kvm_cpuid_array *array)
+{
+	if (array->nent >= array->maxnent)
+		return NULL;
+
+	return &array->entries[array->nent++];
+}
+
 static struct kvm_cpuid_entry2 *do_host_cpuid(struct kvm_cpuid_array *array,
 					      u32 function, u32 index)
 {
-	struct kvm_cpuid_entry2 *entry;
+	struct kvm_cpuid_entry2 *entry = get_next_cpuid(array);
 
-	if (array->nent >= array->maxnent)
+	if (!entry)
 		return NULL;
 
-	entry = &array->entries[array->nent++];
-
 	entry->function = function;
 	entry->index = index;
 	entry->flags = 0;
@@ -699,13 +741,13 @@
 		break;
 	/* function 7 has additional index. */
 	case 7:
-		entry->eax = min(entry->eax, 1u);
+		max_idx = entry->eax = min(entry->eax, 2u);
 		cpuid_entry_override(entry, CPUID_7_0_EBX);
 		cpuid_entry_override(entry, CPUID_7_ECX);
 		cpuid_entry_override(entry, CPUID_7_EDX);
 
-		/* KVM only supports 0x7.0 and 0x7.1, capped above via min(). */
-		if (entry->eax == 1) {
+		/* KVM only supports up to 0x7.2, capped above via min(). */
+		if (max_idx >= 1) {
 			entry = do_host_cpuid(array, function, 1);
 			if (!entry)
 				goto out;
@@ -715,14 +757,27 @@
 			entry->ecx = 0;
 			entry->edx = 0;
 		}
-		break;
-	case 9:
+		if (max_idx >= 2) {
+			entry = do_host_cpuid(array, function, 2);
+			if (!entry)
+				goto out;
+
+			cpuid_entry_override(entry, CPUID_7_2_EDX);
+			entry->ecx = 0;
+			entry->ebx = 0;
+			entry->eax = 0;
+		}
 		break;
 	case 0xa: { /* Architectural Performance Monitoring */
 		struct x86_pmu_capability cap;
 		union cpuid10_eax eax;
 		union cpuid10_edx edx;
 
+		if (!static_cpu_has(X86_FEATURE_ARCH_PERFMON)) {
+			entry->eax = entry->ebx = entry->ecx = entry->edx = 0;
+			break;
+		}
+
 		perf_get_x86_pmu_capability(&cap);
 
 		/*
@@ -750,22 +805,13 @@
 		entry->edx = edx.full;
 		break;
 	}
-	/*
-	 * Per Intel's SDM, the 0x1f is a superset of 0xb,
-	 * thus they can be handled by common code.
-	 */
 	case 0x1f:
 	case 0xb:
 		/*
-		 * Populate entries until the level type (ECX[15:8]) of the
-		 * previous entry is zero.  Note, CPUID EAX.{0x1f,0xb}.0 is
-		 * the starting entry, filled by the primary do_host_cpuid().
+		 * No topology; a valid topology is indicated by the presence
+		 * of subleaf 1.
 		 */
-		for (i = 1; entry->ecx & 0xff00; ++i) {
-			entry = do_host_cpuid(array, function, i);
-			if (!entry)
-				goto out;
-		}
+		entry->eax = entry->ebx = entry->ecx = 0;
 		break;
 	case 0xd:
 		entry->eax &= supported_xcr0;
@@ -897,11 +943,13 @@
 		entry->eax = min(entry->eax, 0x8000001f);
 		break;
 	case 0x80000001:
+		entry->ebx &= ~GENMASK(27, 16);
 		cpuid_entry_override(entry, CPUID_8000_0001_EDX);
 		cpuid_entry_override(entry, CPUID_8000_0001_ECX);
 		break;
 	case 0x80000006:
-		/* L2 cache and TLB: pass through host info. */
+		/* Drop reserved bits, pass host L2 cache and TLB info. */
+		entry->edx &= ~GENMASK(17, 16);
 		break;
 	case 0x80000007: /* Advanced power management */
 		/* invariant TSC is CPUID.80000007H:EDX[8] */
@@ -911,9 +959,8 @@
 		entry->eax = entry->ebx = entry->ecx = 0;
 		break;
 	case 0x80000008: {
-		unsigned g_phys_as = (entry->eax >> 16) & 0xff;
-		unsigned virt_as = max((entry->eax >> 8) & 0xff, 48U);
-		unsigned phys_as = entry->eax & 0xff;
+		unsigned int virt_as = max((entry->eax >> 8) & 0xff, 48U);
+		unsigned int phys_as;
 
 		/*
 		 * If TDP (NPT) is disabled use the adjusted host MAXPHYADDR as
@@ -921,16 +968,17 @@
 		 * reductions in MAXPHYADDR for memory encryption affect shadow
 		 * paging, too.
 		 *
-		 * If TDP is enabled but an explicit guest MAXPHYADDR is not
-		 * provided, use the raw bare metal MAXPHYADDR as reductions to
-		 * the HPAs do not affect GPAs.
+		 * If TDP is enabled, use the raw bare metal MAXPHYADDR as
+		 * reductions to the HPAs do not affect GPAs.
 		 */
-		if (!tdp_enabled)
-			g_phys_as = boot_cpu_data.x86_phys_bits;
-		else if (!g_phys_as)
-			g_phys_as = phys_as;
+		if (!tdp_enabled) {
+			phys_as = boot_cpu_data.x86_phys_bits;
+		} else {
+			phys_as = entry->eax & 0xff;
+		}
 
-		entry->eax = g_phys_as | (virt_as << 8);
+		entry->eax = phys_as | (virt_as << 8);
+		entry->ecx &= ~(GENMASK(31, 16) | GENMASK(11, 8));
 		entry->edx = 0;
 		cpuid_entry_override(entry, CPUID_8000_0008_EBX);
 		break;
@@ -950,14 +998,21 @@
 		entry->ecx = entry->edx = 0;
 		break;
 	case 0x8000001a:
+		entry->eax &= GENMASK(2, 0);
+		entry->ebx = entry->ecx = entry->edx = 0;
+		break;
 	case 0x8000001e:
+		/* Do not return host topology information.  */
+		entry->eax = entry->ebx = entry->ecx = 0;
+		entry->edx = 0; /* reserved */
 		break;
 	case 0x8000001F:
 		if (!kvm_cpu_cap_has(X86_FEATURE_SEV)) {
 			entry->eax = entry->ebx = entry->ecx = entry->edx = 0;
 		} else {
 			cpuid_entry_override(entry, CPUID_8000_001F_EAX);
-
+			/* Clear NumVMPL since KVM does not support VMPL.  */
+			entry->ebx &= ~GENMASK(31, 12);
 			/*
 			 * Enumerate '0' for "PA bits reduction", the adjusted
 			 * MAXPHYADDR is enumerated directly (see 0x80000008).
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/cpuid.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/cpuid.h
@@ -30,6 +30,8 @@
 bool kvm_cpuid(struct kvm_vcpu *vcpu, u32 *eax, u32 *ebx,
 	       u32 *ecx, u32 *edx, bool exact_only);
 
+void __init kvm_init_xstate_sizes(void);
+
 int cpuid_query_maxphyaddr(struct kvm_vcpu *vcpu);
 u64 kvm_vcpu_reserved_gpa_bits_raw(struct kvm_vcpu *vcpu);
 
@@ -121,6 +123,16 @@
 	return best && is_guest_vendor_intel(best->ebx, best->ecx, best->edx);
 }
 
+static inline bool guest_cpuid_is_amd_compatible(struct kvm_vcpu *vcpu)
+{
+	return vcpu->arch.is_amd_compatible;
+}
+
+static inline bool guest_cpuid_is_intel_compatible(struct kvm_vcpu *vcpu)
+{
+	return !guest_cpuid_is_amd_compatible(vcpu);
+}
+
 static inline int guest_cpuid_family(struct kvm_vcpu *vcpu)
 {
 	struct kvm_cpuid_entry2 *best;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/debugfs.c
@@ -95,6 +95,9 @@
 	unsigned int *log[KVM_NR_PAGE_SIZES], *cur;
 	int i, j, k, l, ret;
 
+	if (!kvm_memslots_have_rmaps(kvm))
+		return 0;
+
 	ret = -ENOMEM;
 	memset(log, 0, sizeof(log));
 	for (i = 0; i < KVM_NR_PAGE_SIZES; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/emulate.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/emulate.c
@@ -187,9 +187,6 @@
 #define X8(x...) X4(x), X4(x)
 #define X16(x...) X8(x), X8(x)
 
-#define NR_FASTOP (ilog2(sizeof(ulong)) + 1)
-#define FASTOP_SIZE 8
-
 struct opcode {
 	u64 flags : 56;
 	u64 intercept : 8;
@@ -303,9 +300,15 @@
  * Moreover, they are all exactly FASTOP_SIZE bytes long, so functions for
  * different operand sizes can be reached by calculation, rather than a jump
  * table (which would be bigger than the code).
+ *
+ * The 16 byte alignment, considering 5 bytes for the RET thunk, 3 for ENDBR
+ * and 1 for the straight line speculation INT3, leaves 7 bytes for the
+ * body of the function.  Currently none is larger than 4.
  */
 static int fastop(struct x86_emulate_ctxt *ctxt, fastop_t fop);
 
+#define FASTOP_SIZE	16
+
 #define __FOP_FUNC(name) \
 	".align " __stringify(FASTOP_SIZE) " \n\t" \
 	".type " name ", @function \n\t" \
@@ -315,19 +318,21 @@
 	__FOP_FUNC(#name)
 
 #define __FOP_RET(name) \
-	"ret \n\t" \
+	ASM_RET \
 	".size " name ", .-" name "\n\t"
 
 #define FOP_RET(name) \
 	__FOP_RET(#name)
 
-#define FOP_START(op) \
+#define __FOP_START(op, align) \
 	extern void em_##op(struct fastop *fake); \
 	asm(".pushsection .text, \"ax\" \n\t" \
 	    ".global em_" #op " \n\t" \
-	    ".align " __stringify(FASTOP_SIZE) " \n\t" \
+	    ".align " __stringify(align) " \n\t" \
 	    "em_" #op ":\n\t"
 
+#define FOP_START(op) __FOP_START(op, FASTOP_SIZE)
+
 #define FOP_END \
 	    ".popsection")
 
@@ -427,18 +432,29 @@
 	FOP_END
 
 /* Special case for SETcc - 1 instruction per cc */
+
+/*
+ * Depending on .config the SETcc functions look like:
+ *
+ * SETcc %al			[3 bytes]
+ * RET | JMP __x86_return_thunk	[1,5 bytes; CONFIG_RETHUNK]
+ * INT3				[1 byte; CONFIG_SLS]
+ */
+#define SETCC_ALIGN	16
+
 #define FOP_SETCC(op) \
-	".align 4 \n\t" \
+	".align " __stringify(SETCC_ALIGN) " \n\t" \
 	".type " #op ", @function \n\t" \
 	#op ": \n\t" \
 	#op " %al \n\t" \
-	__FOP_RET(#op)
+	__FOP_RET(#op) \
+	".skip " __stringify(SETCC_ALIGN) " - (.-" #op "), 0xcc \n\t"
 
 asm(".pushsection .fixup, \"ax\"\n"
-    "kvm_fastop_exception: xor %esi, %esi; ret\n"
+    "kvm_fastop_exception: xor %esi, %esi; " ASM_RET
     ".popsection");
 
-FOP_START(setcc)
+__FOP_START(setcc, SETCC_ALIGN)
 FOP_SETCC(seto)
 FOP_SETCC(setno)
 FOP_SETCC(setc)
@@ -671,7 +687,7 @@
 static inline bool emul_is_noncanonical_address(u64 la,
 						struct x86_emulate_ctxt *ctxt)
 {
-	return get_canonical(la, ctxt_virt_addr_bits(ctxt)) != la;
+	return !__is_canonical_address(la, ctxt_virt_addr_bits(ctxt));
 }
 
 /*
@@ -721,7 +737,7 @@
 	case X86EMUL_MODE_PROT64:
 		*linear = la;
 		va_bits = ctxt_virt_addr_bits(ctxt);
-		if (get_canonical(la, va_bits) != la)
+		if (!__is_canonical_address(la, va_bits))
 			goto bad;
 
 		*max_size = min_t(u64, ~0u, (1ull << va_bits) - la);
@@ -779,8 +795,7 @@
 			   ctxt->mode, linear);
 }
 
-static inline int assign_eip(struct x86_emulate_ctxt *ctxt, ulong dst,
-			     enum x86emul_mode mode)
+static inline int assign_eip(struct x86_emulate_ctxt *ctxt, ulong dst)
 {
 	ulong linear;
 	int rc;
@@ -790,41 +805,71 @@
 
 	if (ctxt->op_bytes != sizeof(unsigned long))
 		addr.ea = dst & ((1UL << (ctxt->op_bytes << 3)) - 1);
-	rc = __linearize(ctxt, addr, &max_size, 1, false, true, mode, &linear);
+	rc = __linearize(ctxt, addr, &max_size, 1, false, true, ctxt->mode, &linear);
 	if (rc == X86EMUL_CONTINUE)
 		ctxt->_eip = addr.ea;
 	return rc;
 }
 
+static inline int emulator_recalc_and_set_mode(struct x86_emulate_ctxt *ctxt)
+{
+	u64 efer;
+	struct desc_struct cs;
+	u16 selector;
+	u32 base3;
+
+	ctxt->ops->get_msr(ctxt, MSR_EFER, &efer);
+
+	if (!(ctxt->ops->get_cr(ctxt, 0) & X86_CR0_PE)) {
+		/* Real mode. cpu must not have long mode active */
+		if (efer & EFER_LMA)
+			return X86EMUL_UNHANDLEABLE;
+		ctxt->mode = X86EMUL_MODE_REAL;
+		return X86EMUL_CONTINUE;
+	}
+
+	if (ctxt->eflags & X86_EFLAGS_VM) {
+		/* Protected/VM86 mode. cpu must not have long mode active */
+		if (efer & EFER_LMA)
+			return X86EMUL_UNHANDLEABLE;
+		ctxt->mode = X86EMUL_MODE_VM86;
+		return X86EMUL_CONTINUE;
+	}
+
+	if (!ctxt->ops->get_segment(ctxt, &selector, &cs, &base3, VCPU_SREG_CS))
+		return X86EMUL_UNHANDLEABLE;
+
+	if (efer & EFER_LMA) {
+		if (cs.l) {
+			/* Proper long mode */
+			ctxt->mode = X86EMUL_MODE_PROT64;
+		} else if (cs.d) {
+			/* 32 bit compatibility mode*/
+			ctxt->mode = X86EMUL_MODE_PROT32;
+		} else {
+			ctxt->mode = X86EMUL_MODE_PROT16;
+		}
+	} else {
+		/* Legacy 32 bit / 16 bit mode */
+		ctxt->mode = cs.d ? X86EMUL_MODE_PROT32 : X86EMUL_MODE_PROT16;
+	}
+
+	return X86EMUL_CONTINUE;
+}
+
 static inline int assign_eip_near(struct x86_emulate_ctxt *ctxt, ulong dst)
 {
-	return assign_eip(ctxt, dst, ctxt->mode);
+	return assign_eip(ctxt, dst);
 }
 
-static int assign_eip_far(struct x86_emulate_ctxt *ctxt, ulong dst,
-			  const struct desc_struct *cs_desc)
+static int assign_eip_far(struct x86_emulate_ctxt *ctxt, ulong dst)
 {
-	enum x86emul_mode mode = ctxt->mode;
-	int rc;
+	int rc = emulator_recalc_and_set_mode(ctxt);
 
-#ifdef CONFIG_X86_64
-	if (ctxt->mode >= X86EMUL_MODE_PROT16) {
-		if (cs_desc->l) {
-			u64 efer = 0;
+	if (rc != X86EMUL_CONTINUE)
+		return rc;
 
-			ctxt->ops->get_msr(ctxt, MSR_EFER, &efer);
-			if (efer & EFER_LMA)
-				mode = X86EMUL_MODE_PROT64;
-		} else
-			mode = X86EMUL_MODE_PROT32; /* temporary value */
-	}
-#endif
-	if (mode == X86EMUL_MODE_PROT16 || mode == X86EMUL_MODE_PROT32)
-		mode = cs_desc->d ? X86EMUL_MODE_PROT32 : X86EMUL_MODE_PROT16;
-	rc = assign_eip(ctxt, dst, mode);
-	if (rc == X86EMUL_CONTINUE)
-		ctxt->mode = mode;
-	return rc;
+	return assign_eip(ctxt, dst);
 }
 
 static inline int jmp_rel(struct x86_emulate_ctxt *ctxt, int rel)
@@ -1053,7 +1098,7 @@
 static __always_inline u8 test_cc(unsigned int condition, unsigned long flags)
 {
 	u8 rc;
-	void (*fop)(void) = (void *)em_setcc + 4 * (condition & 0xf);
+	void (*fop)(void) = (void *)em_setcc + SETCC_ALIGN * (condition & 0xf);
 
 	flags = (flags & EFLAGS_MASK) | X86_EFLAGS_IF;
 	asm("push %[flags]; popf; " CALL_NOSPEC
@@ -1614,11 +1659,6 @@
 		goto exception;
 	}
 
-	if (!seg_desc.p) {
-		err_vec = (seg == VCPU_SREG_SS) ? SS_VECTOR : NP_VECTOR;
-		goto exception;
-	}
-
 	dpl = seg_desc.dpl;
 
 	switch (seg) {
@@ -1658,12 +1698,6 @@
 	case VCPU_SREG_TR:
 		if (seg_desc.s || (seg_desc.type != 1 && seg_desc.type != 9))
 			goto exception;
-		old_desc = seg_desc;
-		seg_desc.type |= 2; /* busy */
-		ret = ctxt->ops->cmpxchg_emulated(ctxt, desc_addr, &old_desc, &seg_desc,
-						  sizeof(seg_desc), &ctxt->exception);
-		if (ret != X86EMUL_CONTINUE)
-			return ret;
 		break;
 	case VCPU_SREG_LDTR:
 		if (seg_desc.s || seg_desc.type != 2)
@@ -1682,6 +1716,11 @@
 		break;
 	}
 
+	if (!seg_desc.p) {
+		err_vec = (seg == VCPU_SREG_SS) ? SS_VECTOR : NP_VECTOR;
+		goto exception;
+	}
+
 	if (seg_desc.s) {
 		/* mark segment as accessed */
 		if (!(seg_desc.type & 1)) {
@@ -1696,8 +1735,17 @@
 		if (ret != X86EMUL_CONTINUE)
 			return ret;
 		if (emul_is_noncanonical_address(get_desc_base(&seg_desc) |
-				((u64)base3 << 32), ctxt))
-			return emulate_gp(ctxt, 0);
+						 ((u64)base3 << 32), ctxt))
+			return emulate_gp(ctxt, err_code);
+	}
+
+	if (seg == VCPU_SREG_TR) {
+		old_desc = seg_desc;
+		seg_desc.type |= 2; /* busy */
+		ret = ctxt->ops->cmpxchg_emulated(ctxt, desc_addr, &old_desc, &seg_desc,
+						  sizeof(seg_desc), &ctxt->exception);
+		if (ret != X86EMUL_CONTINUE)
+			return ret;
 	}
 load:
 	ctxt->ops->set_segment(ctxt, selector, &seg_desc, base3, seg);
@@ -1917,7 +1965,7 @@
 	if (rc != X86EMUL_CONTINUE)
 		return rc;
 
-	if (ctxt->modrm_reg == VCPU_SREG_SS)
+	if (seg == VCPU_SREG_SS)
 		ctxt->interruptibility = KVM_X86_SHADOW_INT_MOV_SS;
 	if (ctxt->op_bytes > 2)
 		rsp_increment(ctxt, ctxt->op_bytes - 2);
@@ -2134,7 +2182,7 @@
 	if (rc != X86EMUL_CONTINUE)
 		return rc;
 
-	rc = assign_eip_far(ctxt, ctxt->src.val, &new_desc);
+	rc = assign_eip_far(ctxt, ctxt->src.val);
 	/* Error handling is not implemented. */
 	if (rc != X86EMUL_CONTINUE)
 		return X86EMUL_UNHANDLEABLE;
@@ -2215,7 +2263,7 @@
 				       &new_desc);
 	if (rc != X86EMUL_CONTINUE)
 		return rc;
-	rc = assign_eip_far(ctxt, eip, &new_desc);
+	rc = assign_eip_far(ctxt, eip);
 	/* Error handling is not implemented. */
 	if (rc != X86EMUL_CONTINUE)
 		return X86EMUL_UNHANDLEABLE;
@@ -2598,7 +2646,7 @@
 	 * those side effects need to be explicitly handled for both success
 	 * and shutdown.
 	 */
-	return X86EMUL_CONTINUE;
+	return emulator_recalc_and_set_mode(ctxt);
 
 emulate_shutdown:
 	ctxt->ops->triple_fault(ctxt);
@@ -2842,6 +2890,7 @@
 	ops->set_segment(ctxt, ss_sel, &ss, 0, VCPU_SREG_SS);
 
 	ctxt->_eip = rdx;
+	ctxt->mode = usermode;
 	*reg_write(ctxt, VCPU_REGS_RSP) = rcx;
 
 	return X86EMUL_CONTINUE;
@@ -3438,7 +3487,7 @@
 	if (rc != X86EMUL_CONTINUE)
 		return rc;
 
-	rc = assign_eip_far(ctxt, ctxt->src.val, &new_desc);
+	rc = assign_eip_far(ctxt, ctxt->src.val);
 	if (rc != X86EMUL_CONTINUE)
 		goto fail;
 
@@ -3510,8 +3559,10 @@
 {
 	u64 tsc_aux = 0;
 
-	if (ctxt->ops->get_msr(ctxt, MSR_TSC_AUX, &tsc_aux))
+	if (!ctxt->ops->guest_has_rdpid(ctxt))
 		return emulate_ud(ctxt);
+
+	ctxt->ops->get_msr(ctxt, MSR_TSC_AUX, &tsc_aux);
 	ctxt->dst.val = tsc_aux;
 	return X86EMUL_CONTINUE;
 }
@@ -3578,11 +3629,25 @@
 
 static int em_cr_write(struct x86_emulate_ctxt *ctxt)
 {
-	if (ctxt->ops->set_cr(ctxt, ctxt->modrm_reg, ctxt->src.val))
+	int cr_num = ctxt->modrm_reg;
+	int r;
+
+	if (ctxt->ops->set_cr(ctxt, cr_num, ctxt->src.val))
 		return emulate_gp(ctxt, 0);
 
 	/* Disable writeback. */
 	ctxt->dst.type = OP_NONE;
+
+	if (cr_num == 0) {
+		/*
+		 * CR0 write might have updated CR0.PE and/or CR0.PG
+		 * which can affect the cpu's execution mode.
+		 */
+		r = emulator_recalc_and_set_mode(ctxt);
+		if (r != X86EMUL_CONTINUE)
+			return r;
+	}
+
 	return X86EMUL_CONTINUE;
 }
 
@@ -4101,6 +4166,9 @@
 {
 	u32 eax, ecx, edx;
 
+	if (!(ctxt->ops->get_cr(ctxt, 4) & X86_CR4_OSXSAVE))
+		return emulate_ud(ctxt);
+
 	eax = reg_read(ctxt, VCPU_REGS_RAX);
 	edx = reg_read(ctxt, VCPU_REGS_RDX);
 	ecx = reg_read(ctxt, VCPU_REGS_RCX);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/hyperv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/hyperv.c
@@ -236,7 +236,7 @@
 	struct kvm_vcpu *vcpu = hv_synic_to_vcpu(synic);
 	int ret;
 
-	if (!synic->active && !host)
+	if (!synic->active && (!host || data))
 		return 1;
 
 	trace_kvm_hv_synic_set_msr(vcpu->vcpu_id, msr, data, host);
@@ -282,6 +282,9 @@
 	case HV_X64_MSR_EOM: {
 		int i;
 
+		if (!synic->active)
+			break;
+
 		for (i = 0; i < ARRAY_SIZE(synic->sint); i++)
 			kvm_hv_notify_acked_sint(vcpu, i);
 		break;
@@ -446,6 +449,9 @@
 	struct kvm_lapic_irq irq;
 	int ret, vector;
 
+	if (KVM_BUG_ON(!lapic_in_kernel(vcpu), vcpu->kvm))
+		return -EINVAL;
+
 	if (sint >= ARRAY_SIZE(synic->sint))
 		return -EINVAL;
 
@@ -658,7 +664,7 @@
 	struct kvm_vcpu_hv *hv_vcpu = to_hv_vcpu(vcpu);
 	struct kvm_vcpu_hv_synic *synic = to_hv_synic(vcpu);
 
-	if (!synic->active && !host)
+	if (!synic->active && (!host || config))
 		return 1;
 
 	if (unlikely(!host && hv_vcpu->enforce_cpuid && new_config.direct_mode &&
@@ -687,7 +693,7 @@
 	struct kvm_vcpu *vcpu = hv_stimer_to_vcpu(stimer);
 	struct kvm_vcpu_hv_synic *synic = to_hv_synic(vcpu);
 
-	if (!synic->active && !host)
+	if (!synic->active && (!host || count))
 		return 1;
 
 	trace_kvm_hv_stimer_set_count(hv_stimer_to_vcpu(stimer)->vcpu_id,
@@ -695,10 +701,12 @@
 
 	stimer_cleanup(stimer);
 	stimer->count = count;
-	if (stimer->count == 0)
-		stimer->config.enable = 0;
-	else if (stimer->config.auto_enable)
-		stimer->config.enable = 1;
+	if (!host) {
+		if (stimer->count == 0)
+			stimer->config.enable = 0;
+		else if (stimer->config.auto_enable)
+			stimer->config.enable = 1;
+	}
 
 	if (stimer->config.enable)
 		stimer_mark_pending(stimer, false);
@@ -1749,7 +1757,7 @@
 	sse128_t xmm[HV_HYPERCALL_MAX_XMM_REGISTERS];
 };
 
-static u64 kvm_hv_flush_tlb(struct kvm_vcpu *vcpu, struct kvm_hv_hcall *hc, bool ex)
+static u64 kvm_hv_flush_tlb(struct kvm_vcpu *vcpu, struct kvm_hv_hcall *hc)
 {
 	int i;
 	gpa_t gpa;
@@ -1765,7 +1773,8 @@
 	int sparse_banks_len;
 	bool all_cpus;
 
-	if (!ex) {
+	if (hc->code == HVCALL_FLUSH_VIRTUAL_ADDRESS_LIST ||
+	    hc->code == HVCALL_FLUSH_VIRTUAL_ADDRESS_SPACE) {
 		if (hc->fast) {
 			flush.address_space = hc->ingpa;
 			flush.flags = hc->outgpa;
@@ -1819,7 +1828,8 @@
 
 		if (!all_cpus) {
 			if (hc->fast) {
-				if (sparse_banks_len > HV_HYPERCALL_MAX_XMM_REGISTERS - 1)
+				/* XMM0 is already consumed, each XMM holds two sparse banks. */
+				if (sparse_banks_len > 2 * (HV_HYPERCALL_MAX_XMM_REGISTERS - 1))
 					return HV_STATUS_INVALID_HYPERCALL_INPUT;
 				for (i = 0; i < sparse_banks_len; i += 2) {
 					sparse_banks[i] = sse128_lo(hc->xmm[i / 2 + 1]);
@@ -1838,16 +1848,19 @@
 
 	cpumask_clear(&hv_vcpu->tlb_flush);
 
-	vcpu_mask = all_cpus ? NULL :
-		sparse_set_to_vcpu_mask(kvm, sparse_banks, valid_bank_mask,
-					vp_bitmap, vcpu_bitmap);
-
 	/*
 	 * vcpu->arch.cr3 may not be up-to-date for running vCPUs so we can't
 	 * analyze it here, flush TLB regardless of the specified address space.
 	 */
-	kvm_make_vcpus_request_mask(kvm, KVM_REQ_TLB_FLUSH_GUEST,
-				    NULL, vcpu_mask, &hv_vcpu->tlb_flush);
+	if (all_cpus) {
+		kvm_make_all_cpus_request(kvm, KVM_REQ_TLB_FLUSH_GUEST);
+	} else {
+		vcpu_mask = sparse_set_to_vcpu_mask(kvm, sparse_banks, valid_bank_mask,
+						    vp_bitmap, vcpu_bitmap);
+
+		kvm_make_vcpus_request_mask(kvm, KVM_REQ_TLB_FLUSH_GUEST,
+					    NULL, vcpu_mask, &hv_vcpu->tlb_flush);
+	}
 
 ret_success:
 	/* We always do full TLB flush, set 'Reps completed' = 'Rep Count' */
@@ -1874,7 +1887,7 @@
 	}
 }
 
-static u64 kvm_hv_send_ipi(struct kvm_vcpu *vcpu, struct kvm_hv_hcall *hc, bool ex)
+static u64 kvm_hv_send_ipi(struct kvm_vcpu *vcpu, struct kvm_hv_hcall *hc)
 {
 	struct kvm *kvm = vcpu->kvm;
 	struct hv_send_ipi_ex send_ipi_ex;
@@ -1887,8 +1900,12 @@
 	int sparse_banks_len;
 	u32 vector;
 	bool all_cpus;
+	int i;
 
-	if (!ex) {
+	if (!lapic_in_kernel(vcpu))
+		return HV_STATUS_INVALID_HYPERCALL_INPUT;
+
+	if (hc->code == HVCALL_SEND_IPI) {
 		if (!hc->fast) {
 			if (unlikely(kvm_read_guest(kvm, hc->ingpa, &send_ipi,
 						    sizeof(send_ipi))))
@@ -1907,9 +1924,15 @@
 
 		trace_kvm_hv_send_ipi(vector, sparse_banks[0]);
 	} else {
-		if (unlikely(kvm_read_guest(kvm, hc->ingpa, &send_ipi_ex,
-					    sizeof(send_ipi_ex))))
-			return HV_STATUS_INVALID_HYPERCALL_INPUT;
+		if (!hc->fast) {
+			if (unlikely(kvm_read_guest(kvm, hc->ingpa, &send_ipi_ex,
+						    sizeof(send_ipi_ex))))
+				return HV_STATUS_INVALID_HYPERCALL_INPUT;
+		} else {
+			send_ipi_ex.vector = (u32)hc->ingpa;
+			send_ipi_ex.vp_set.format = hc->outgpa;
+			send_ipi_ex.vp_set.valid_bank_mask = sse128_lo(hc->xmm[0]);
+		}
 
 		trace_kvm_hv_send_ipi_ex(send_ipi_ex.vector,
 					 send_ipi_ex.vp_set.format,
@@ -1917,23 +1940,40 @@
 
 		vector = send_ipi_ex.vector;
 		valid_bank_mask = send_ipi_ex.vp_set.valid_bank_mask;
-		sparse_banks_len = bitmap_weight(&valid_bank_mask, 64) *
-			sizeof(sparse_banks[0]);
+		sparse_banks_len = bitmap_weight(&valid_bank_mask, 64);
 
 		all_cpus = send_ipi_ex.vp_set.format == HV_GENERIC_SET_ALL;
 
+		if (all_cpus)
+			goto check_and_send_ipi;
+
 		if (!sparse_banks_len)
 			goto ret_success;
 
-		if (!all_cpus &&
-		    kvm_read_guest(kvm,
-				   hc->ingpa + offsetof(struct hv_send_ipi_ex,
-							vp_set.bank_contents),
-				   sparse_banks,
-				   sparse_banks_len))
-			return HV_STATUS_INVALID_HYPERCALL_INPUT;
+		if (!hc->fast) {
+			if (kvm_read_guest(kvm,
+					   hc->ingpa + offsetof(struct hv_send_ipi_ex,
+								vp_set.bank_contents),
+					   sparse_banks,
+					   sparse_banks_len * sizeof(sparse_banks[0])))
+				return HV_STATUS_INVALID_HYPERCALL_INPUT;
+		} else {
+			/*
+			 * The lower half of XMM0 is already consumed, each XMM holds
+			 * two sparse banks.
+			 */
+			if (sparse_banks_len > (2 * HV_HYPERCALL_MAX_XMM_REGISTERS - 1))
+				return HV_STATUS_INVALID_HYPERCALL_INPUT;
+			for (i = 0; i < sparse_banks_len; i++) {
+				if (i % 2)
+					sparse_banks[i] = sse128_lo(hc->xmm[(i + 1) / 2]);
+				else
+					sparse_banks[i] = sse128_hi(hc->xmm[i / 2]);
+			}
+		}
 	}
 
+check_and_send_ipi:
 	if ((vector < HV_IPI_LOW_VECTOR) || (vector > HV_IPI_HIGH_VECTOR))
 		return HV_STATUS_INVALID_HYPERCALL_INPUT;
 
@@ -2022,7 +2062,7 @@
 {
 	bool longmode;
 
-	longmode = is_64_bit_mode(vcpu);
+	longmode = is_64_bit_hypercall(vcpu);
 	if (longmode)
 		kvm_rax_write(vcpu, result);
 	else {
@@ -2092,6 +2132,7 @@
 	case HVCALL_FLUSH_VIRTUAL_ADDRESS_SPACE:
 	case HVCALL_FLUSH_VIRTUAL_ADDRESS_LIST_EX:
 	case HVCALL_FLUSH_VIRTUAL_ADDRESS_SPACE_EX:
+	case HVCALL_SEND_IPI_EX:
 		return true;
 	}
 
@@ -2171,7 +2212,7 @@
 	}
 
 #ifdef CONFIG_X86_64
-	if (is_64_bit_mode(vcpu)) {
+	if (is_64_bit_hypercall(vcpu)) {
 		hc.param = kvm_rcx_read(vcpu);
 		hc.ingpa = kvm_rdx_read(vcpu);
 		hc.outgpa = kvm_r8_read(vcpu);
@@ -2243,46 +2284,28 @@
 				kvm_hv_hypercall_complete_userspace;
 		return 0;
 	case HVCALL_FLUSH_VIRTUAL_ADDRESS_LIST:
-		if (unlikely(!hc.rep_cnt || hc.rep_idx)) {
-			ret = HV_STATUS_INVALID_HYPERCALL_INPUT;
-			break;
-		}
-		ret = kvm_hv_flush_tlb(vcpu, &hc, false);
-		break;
-	case HVCALL_FLUSH_VIRTUAL_ADDRESS_SPACE:
-		if (unlikely(hc.rep)) {
-			ret = HV_STATUS_INVALID_HYPERCALL_INPUT;
-			break;
-		}
-		ret = kvm_hv_flush_tlb(vcpu, &hc, false);
-		break;
 	case HVCALL_FLUSH_VIRTUAL_ADDRESS_LIST_EX:
 		if (unlikely(!hc.rep_cnt || hc.rep_idx)) {
 			ret = HV_STATUS_INVALID_HYPERCALL_INPUT;
 			break;
 		}
-		ret = kvm_hv_flush_tlb(vcpu, &hc, true);
+		ret = kvm_hv_flush_tlb(vcpu, &hc);
 		break;
+	case HVCALL_FLUSH_VIRTUAL_ADDRESS_SPACE:
 	case HVCALL_FLUSH_VIRTUAL_ADDRESS_SPACE_EX:
 		if (unlikely(hc.rep)) {
 			ret = HV_STATUS_INVALID_HYPERCALL_INPUT;
 			break;
 		}
-		ret = kvm_hv_flush_tlb(vcpu, &hc, true);
+		ret = kvm_hv_flush_tlb(vcpu, &hc);
 		break;
 	case HVCALL_SEND_IPI:
-		if (unlikely(hc.rep)) {
-			ret = HV_STATUS_INVALID_HYPERCALL_INPUT;
-			break;
-		}
-		ret = kvm_hv_send_ipi(vcpu, &hc, false);
-		break;
 	case HVCALL_SEND_IPI_EX:
-		if (unlikely(hc.fast || hc.rep)) {
+		if (unlikely(hc.rep)) {
 			ret = HV_STATUS_INVALID_HYPERCALL_INPUT;
 			break;
 		}
-		ret = kvm_hv_send_ipi(vcpu, &hc, true);
+		ret = kvm_hv_send_ipi(vcpu, &hc);
 		break;
 	case HVCALL_POST_DEBUG_DATA:
 	case HVCALL_RETRIEVE_DEBUG_DATA:
@@ -2487,7 +2510,8 @@
 			ent->eax |= HV_X64_REMOTE_TLB_FLUSH_RECOMMENDED;
 			ent->eax |= HV_X64_APIC_ACCESS_RECOMMENDED;
 			ent->eax |= HV_X64_RELAXED_TIMING_RECOMMENDED;
-			ent->eax |= HV_X64_CLUSTER_IPI_RECOMMENDED;
+			if (!vcpu || lapic_in_kernel(vcpu))
+				ent->eax |= HV_X64_CLUSTER_IPI_RECOMMENDED;
 			ent->eax |= HV_X64_EX_PROCESSOR_MASKS_RECOMMENDED;
 			if (evmcs_ver)
 				ent->eax |= HV_X64_ENLIGHTENED_VMCS_RECOMMENDED;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/ioapic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/ioapic.c
@@ -96,7 +96,7 @@
 static void rtc_irq_eoi_tracking_reset(struct kvm_ioapic *ioapic)
 {
 	ioapic->rtc_status.pending_eoi = 0;
-	bitmap_zero(ioapic->rtc_status.dest_map.map, KVM_MAX_VCPU_ID + 1);
+	bitmap_zero(ioapic->rtc_status.dest_map.map, KVM_MAX_VCPU_ID);
 }
 
 static void kvm_rtc_eoi_tracking_restore_all(struct kvm_ioapic *ioapic);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/ioapic.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/ioapic.h
@@ -39,13 +39,13 @@
 
 struct dest_map {
 	/* vcpu bitmap where IRQ has been sent */
-	DECLARE_BITMAP(map, KVM_MAX_VCPU_ID + 1);
+	DECLARE_BITMAP(map, KVM_MAX_VCPU_ID);
 
 	/*
 	 * Vector sent to a given vcpu, only valid when
 	 * the vcpu's bit in map is set
 	 */
-	u8 vectors[KVM_MAX_VCPU_ID + 1];
+	u8 vectors[KVM_MAX_VCPU_ID];
 };
 
 
@@ -81,7 +81,6 @@
 	unsigned long irq_states[IOAPIC_NUM_PINS];
 	struct kvm_io_device dev;
 	struct kvm *kvm;
-	void (*ack_notifier)(void *opaque, int irq);
 	spinlock_t lock;
 	struct rtc_status rtc_status;
 	struct delayed_work eoi_inject;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/irq.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/irq.h
@@ -56,7 +56,6 @@
 	struct kvm_io_device dev_master;
 	struct kvm_io_device dev_slave;
 	struct kvm_io_device dev_elcr;
-	void (*ack_notifier)(void *opaque, int irq);
 	unsigned long irq_states[PIC_NUM_PINS];
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/kvm_emulate.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/kvm_emulate.h
@@ -226,6 +226,7 @@
 	bool (*guest_has_long_mode)(struct x86_emulate_ctxt *ctxt);
 	bool (*guest_has_movbe)(struct x86_emulate_ctxt *ctxt);
 	bool (*guest_has_fxsr)(struct x86_emulate_ctxt *ctxt);
+	bool (*guest_has_rdpid)(struct x86_emulate_ctxt *ctxt);
 
 	void (*set_nmi_mask)(struct x86_emulate_ctxt *ctxt, bool masked);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/lapic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/lapic.c
@@ -113,7 +113,8 @@
 
 static bool kvm_can_post_timer_interrupt(struct kvm_vcpu *vcpu)
 {
-	return pi_inject_timer && kvm_vcpu_apicv_active(vcpu);
+	return pi_inject_timer && kvm_vcpu_apicv_active(vcpu) &&
+		(kvm_mwait_in_guest(vcpu->kvm) || kvm_hlt_in_guest(vcpu->kvm));
 }
 
 bool kvm_can_use_hv_timer(struct kvm_vcpu *vcpu)
@@ -676,38 +677,32 @@
 static bool pv_eoi_get_pending(struct kvm_vcpu *vcpu)
 {
 	u8 val;
-	if (pv_eoi_get_user(vcpu, &val) < 0) {
-		printk(KERN_WARNING "Can't read EOI MSR value: 0x%llx\n",
-			   (unsigned long long)vcpu->arch.pv_eoi.msr_val);
+	if (pv_eoi_get_user(vcpu, &val) < 0)
 		return false;
-	}
+
 	return val & KVM_PV_EOI_ENABLED;
 }
 
 static void pv_eoi_set_pending(struct kvm_vcpu *vcpu)
 {
-	if (pv_eoi_put_user(vcpu, KVM_PV_EOI_ENABLED) < 0) {
-		printk(KERN_WARNING "Can't set EOI MSR value: 0x%llx\n",
-			   (unsigned long long)vcpu->arch.pv_eoi.msr_val);
+	if (pv_eoi_put_user(vcpu, KVM_PV_EOI_ENABLED) < 0)
 		return;
-	}
+
 	__set_bit(KVM_APIC_PV_EOI_PENDING, &vcpu->arch.apic_attention);
 }
 
 static void pv_eoi_clr_pending(struct kvm_vcpu *vcpu)
 {
-	if (pv_eoi_put_user(vcpu, KVM_PV_EOI_DISABLED) < 0) {
-		printk(KERN_WARNING "Can't clear EOI MSR value: 0x%llx\n",
-			   (unsigned long long)vcpu->arch.pv_eoi.msr_val);
+	if (pv_eoi_put_user(vcpu, KVM_PV_EOI_DISABLED) < 0)
 		return;
-	}
+
 	__clear_bit(KVM_APIC_PV_EOI_PENDING, &vcpu->arch.apic_attention);
 }
 
 static int apic_has_interrupt_for_ppr(struct kvm_lapic *apic, u32 ppr)
 {
 	int highest_irr;
-	if (apic->vcpu->arch.apicv_active)
+	if (kvm_x86_ops.sync_pir_to_irr)
 		highest_irr = static_call(kvm_x86_sync_pir_to_irr)(apic->vcpu);
 	else
 		highest_irr = apic_find_highest_irr(apic);
@@ -993,6 +988,10 @@
 	*r = -1;
 
 	if (irq->shorthand == APIC_DEST_SELF) {
+		if (KVM_BUG_ON(!src, kvm)) {
+			*r = 0;
+			return true;
+		}
 		*r = kvm_apic_set_irq(src->vcpu, irq, dest_map);
 		return true;
 	}
@@ -1296,6 +1295,7 @@
 
 	kvm_irq_delivery_to_apic(apic->vcpu->kvm, apic, &irq, NULL);
 }
+EXPORT_SYMBOL_GPL(kvm_apic_send_ipi);
 
 static u32 apic_get_tmcct(struct kvm_lapic *apic)
 {
@@ -1507,6 +1507,7 @@
 	if (apic->lapic_timer.hv_timer_in_use)
 		cancel_hv_timer(apic);
 	preempt_enable();
+	atomic_set(&apic->lapic_timer.pending, 0);
 }
 
 static void apic_update_lvtt(struct kvm_lapic *apic)
@@ -2127,11 +2128,14 @@
 		break;
 
 	case APIC_SELF_IPI:
-		if (apic_x2apic_mode(apic)) {
-			kvm_lapic_reg_write(apic, APIC_ICR,
-					    APIC_DEST_SELF | (val & APIC_VECTOR_MASK));
-		} else
+		/*
+		 * Self-IPI exists only when x2APIC is enabled.  Bits 7:0 hold
+		 * the vector, everything else is reserved.
+		 */
+		if (!apic_x2apic_mode(apic) || (val & ~APIC_VECTOR_MASK))
 			ret = 1;
+		else
+			kvm_apic_send_ipi(apic, APIC_DEST_SELF | val, 0);
 		break;
 	default:
 		ret = 1;
@@ -2248,10 +2252,7 @@
 
 void kvm_lapic_set_tpr(struct kvm_vcpu *vcpu, unsigned long cr8)
 {
-	struct kvm_lapic *apic = vcpu->arch.apic;
-
-	apic_set_tpr(apic, ((cr8 & 0x0f) << 4)
-		     | (kvm_lapic_get_reg(apic, APIC_TASKPRI) & 4));
+	apic_set_tpr(vcpu->arch.apic, (cr8 & 0x0f) << 4);
 }
 
 u64 kvm_lapic_get_cr8(struct kvm_vcpu *vcpu)
@@ -2315,6 +2316,7 @@
 		apic->irr_pending = (apic_search_irr(apic) != -1);
 		apic->isr_count = count_vectors(apic->regs + APIC_ISR);
 	}
+	apic->highest_isr_cache = -1;
 }
 EXPORT_SYMBOL_GPL(kvm_apic_update_apicv);
 
@@ -2367,7 +2369,6 @@
 		kvm_lapic_set_reg(apic, APIC_TMR + 0x10 * i, 0);
 	}
 	kvm_apic_update_apicv(vcpu);
-	apic->highest_isr_cache = -1;
 	update_divide_count(apic);
 	atomic_set(&apic->lapic_timer.pending, 0);
 
@@ -2410,13 +2411,18 @@
 {
 	u32 reg = kvm_lapic_get_reg(apic, lvt_type);
 	int vector, mode, trig_mode;
+	int r;
 
 	if (kvm_apic_hw_enabled(apic) && !(reg & APIC_LVT_MASKED)) {
 		vector = reg & APIC_VECTOR_MASK;
 		mode = reg & APIC_MODE_MASK;
 		trig_mode = reg & APIC_LVT_LEVEL_TRIGGER;
-		return __apic_accept_irq(apic, mode, vector, 1, trig_mode,
-					NULL);
+
+		r = __apic_accept_irq(apic, mode, vector, 1, trig_mode, NULL);
+		if (r && lvt_type == APIC_LVTPC &&
+		    guest_cpuid_is_intel_compatible(apic->vcpu))
+			kvm_lapic_set_reg(apic, APIC_LVTPC, reg | APIC_LVT_MASKED);
+		return r;
 	}
 	return 0;
 }
@@ -2629,7 +2635,7 @@
 	kvm_apic_set_version(vcpu);
 
 	apic_update_ppr(apic);
-	hrtimer_cancel(&apic->lapic_timer.timer);
+	cancel_apic_timer(apic);
 	apic->lapic_timer.expired_tscdeadline = 0;
 	apic_update_lvtt(apic);
 	apic_manage_nmi_watchdog(apic, kvm_lapic_get_reg(apic, APIC_LVT0));
@@ -2637,7 +2643,6 @@
 	__start_apic_timer(apic, APIC_TMCCT);
 	kvm_lapic_set_reg(apic, APIC_TMCCT, 0);
 	kvm_apic_update_apicv(vcpu);
-	apic->highest_isr_cache = -1;
 	if (vcpu->arch.apicv_active) {
 		static_call(kvm_x86_apicv_post_state_restore)(vcpu);
 		static_call(kvm_x86_hwapic_irr_update)(vcpu,
@@ -2801,6 +2806,10 @@
 	/* if this is ICR write vector before command */
 	if (reg == APIC_ICR)
 		kvm_lapic_reg_write(apic, APIC_ICR2, (u32)(data >> 32));
+	else if (data >> 32)
+		/* Bits 63:32 are reserved in all other registers. */
+		return 1;
+
 	return kvm_lapic_reg_write(apic, reg, (u32)data);
 }
 
@@ -2835,6 +2844,10 @@
 	/* if this is ICR write vector before command */
 	if (reg == APIC_ICR)
 		kvm_lapic_reg_write(apic, APIC_ICR2, (u32)(data >> 32));
+	else if (data >> 32)
+		/* Bits 63:32 are reserved in all other registers. */
+		return 1;
+
 	return kvm_lapic_reg_write(apic, reg, (u32)data);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu.h
@@ -49,6 +49,7 @@
 			       X86_CR4_LA57)
 
 #define KVM_MMU_CR0_ROLE_BITS (X86_CR0_PG | X86_CR0_WP)
+#define KVM_MMU_EFER_ROLE_BITS (EFER_LME | EFER_NX)
 
 static __always_inline u64 rsvd_bits(int s, int e)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/mmu.c
@@ -1071,20 +1071,6 @@
 	return kvm_mmu_memory_cache_nr_free_objects(mc);
 }
 
-static int rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn)
-{
-	struct kvm_memory_slot *slot;
-	struct kvm_mmu_page *sp;
-	struct kvm_rmap_head *rmap_head;
-
-	sp = sptep_to_sp(spte);
-	kvm_mmu_page_set_gfn(sp, spte - sp->spt, gfn);
-	slot = kvm_vcpu_gfn_to_memslot(vcpu, gfn);
-	rmap_head = gfn_to_rmap(gfn, sp->role.level, slot);
-	return pte_list_add(vcpu, spte, rmap_head);
-}
-
-
 static void rmap_remove(struct kvm *kvm, u64 *spte)
 {
 	struct kvm_memslots *slots;
@@ -1097,9 +1083,9 @@
 	gfn = kvm_mmu_page_get_gfn(sp, spte - sp->spt);
 
 	/*
-	 * Unlike rmap_add and rmap_recycle, rmap_remove does not run in the
-	 * context of a vCPU so have to determine which memslots to use based
-	 * on context information in sp->role.
+	 * Unlike rmap_add, rmap_remove does not run in the context of a vCPU
+	 * so we have to determine which memslots to use based on context
+	 * information in sp->role.
 	 */
 	slots = kvm_memslots_for_spte_role(kvm, sp->role);
 
@@ -1592,7 +1578,7 @@
 		flush = kvm_handle_gfn_range(kvm, range, kvm_unmap_rmapp);
 
 	if (is_tdp_mmu_enabled(kvm))
-		flush |= kvm_tdp_mmu_unmap_gfn_range(kvm, range, flush);
+		flush = kvm_tdp_mmu_unmap_gfn_range(kvm, range, flush);
 
 	return flush;
 }
@@ -1639,19 +1625,24 @@
 
 #define RMAP_RECYCLE_THRESHOLD 1000
 
-static void rmap_recycle(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn)
+static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn)
 {
 	struct kvm_memory_slot *slot;
-	struct kvm_rmap_head *rmap_head;
 	struct kvm_mmu_page *sp;
+	struct kvm_rmap_head *rmap_head;
+	int rmap_count;
 
 	sp = sptep_to_sp(spte);
+	kvm_mmu_page_set_gfn(sp, spte - sp->spt, gfn);
 	slot = kvm_vcpu_gfn_to_memslot(vcpu, gfn);
 	rmap_head = gfn_to_rmap(gfn, sp->role.level, slot);
+	rmap_count = pte_list_add(vcpu, spte, rmap_head);
 
-	kvm_unmap_rmapp(vcpu->kvm, rmap_head, NULL, gfn, sp->role.level, __pte(0));
-	kvm_flush_remote_tlbs_with_address(vcpu->kvm, sp->gfn,
-			KVM_PAGES_PER_HPAGE(sp->role.level));
+	if (rmap_count > RMAP_RECYCLE_THRESHOLD) {
+		kvm_unmap_rmapp(vcpu->kvm, rmap_head, NULL, gfn, sp->role.level, __pte(0));
+		kvm_flush_remote_tlbs_with_address(
+				vcpu->kvm, sp->gfn, KVM_PAGES_PER_HPAGE(sp->role.level));
+	}
 }
 
 bool kvm_age_gfn(struct kvm *kvm, struct kvm_gfn_range *range)
@@ -2188,10 +2179,10 @@
 	iterator->shadow_addr = root;
 	iterator->level = vcpu->arch.mmu->shadow_root_level;
 
-	if (iterator->level == PT64_ROOT_4LEVEL &&
+	if (iterator->level >= PT64_ROOT_4LEVEL &&
 	    vcpu->arch.mmu->root_level < PT64_ROOT_4LEVEL &&
 	    !vcpu->arch.mmu->direct_map)
-		--iterator->level;
+		iterator->level = PT32E_ROOT_LEVEL;
 
 	if (iterator->level == PT32E_ROOT_LEVEL) {
 		/*
@@ -2366,6 +2357,7 @@
 {
 	bool list_unstable;
 
+	lockdep_assert_held_write(&kvm->mmu_lock);
 	trace_kvm_mmu_prepare_zap_page(sp);
 	++kvm->stat.mmu_shadow_zapped;
 	*nr_zapped = mmu_zap_unsync_children(kvm, sp, invalid_list);
@@ -2718,7 +2710,6 @@
 			bool host_writable)
 {
 	int was_rmapped = 0;
-	int rmap_count;
 	int set_spte_ret;
 	int ret = RET_PF_FIXED;
 	bool flush = false;
@@ -2778,9 +2769,7 @@
 
 	if (!was_rmapped) {
 		kvm_update_page_stats(vcpu->kvm, level, 1);
-		rmap_count = rmap_add(vcpu, sptep, gfn);
-		if (rmap_count > RMAP_RECYCLE_THRESHOLD)
-			rmap_recycle(vcpu, sptep, gfn);
+		rmap_add(vcpu, sptep, gfn);
 	}
 
 	return ret;
@@ -3314,6 +3303,8 @@
 		return;
 
 	sp = to_shadow_page(*root_hpa & PT64_BASE_ADDR_MASK);
+	if (WARN_ON(!sp))
+		return;
 
 	if (is_tdp_mmu_page(sp))
 		kvm_tdp_mmu_put_root(kvm, sp, false);
@@ -3579,7 +3570,7 @@
 out_unlock:
 	write_unlock(&vcpu->kvm->mmu_lock);
 
-	return 0;
+	return r;
 }
 
 static int mmu_alloc_special_roots(struct kvm_vcpu *vcpu)
@@ -3889,12 +3880,23 @@
 	walk_shadow_page_lockless_end(vcpu);
 }
 
+static u32 alloc_apf_token(struct kvm_vcpu *vcpu)
+{
+	/* make sure the token value is not 0 */
+	u32 id = vcpu->arch.apf.id;
+
+	if (id << 12 == 0)
+		vcpu->arch.apf.id = 1;
+
+	return (vcpu->arch.apf.id++ << 12) | vcpu->vcpu_id;
+}
+
 static bool kvm_arch_setup_async_pf(struct kvm_vcpu *vcpu, gpa_t cr2_or_gpa,
 				    gfn_t gfn)
 {
 	struct kvm_arch_async_pf arch;
 
-	arch.token = (vcpu->arch.apf.id++ << 12) | vcpu->vcpu_id;
+	arch.token = alloc_apf_token(vcpu);
 	arch.gfn = gfn;
 	arch.direct_map = vcpu->arch.mmu->direct_map;
 	arch.cr3 = vcpu->arch.mmu->get_guest_pgd(vcpu);
@@ -3956,6 +3958,7 @@
 
 	*pfn = __gfn_to_pfn_memslot(slot, gfn, false, NULL,
 				    write, writable, hva);
+	return false;
 
 out_retry:
 	*r = RET_PF_RETRY;
@@ -4005,16 +4008,17 @@
 
 	if (!is_noslot_pfn(pfn) && mmu_notifier_retry_hva(vcpu->kvm, mmu_seq, hva))
 		goto out_unlock;
-	r = make_mmu_pages_available(vcpu);
-	if (r)
-		goto out_unlock;
 
-	if (is_tdp_mmu_fault)
+	if (is_tdp_mmu_fault) {
 		r = kvm_tdp_mmu_map(vcpu, gpa, error_code, map_writable, max_level,
 				    pfn, prefault);
-	else
+	} else {
+		r = make_mmu_pages_available(vcpu);
+		if (r)
+			goto out_unlock;
 		r = __direct_map(vcpu, gpa, error_code, map_writable, max_level, pfn,
 				 prefault, is_tdp);
+	}
 
 out_unlock:
 	if (is_tdp_mmu_fault)
@@ -4347,7 +4351,7 @@
 				context->root_level, is_efer_nx(context),
 				guest_can_use_gbpages(vcpu),
 				is_cr4_pse(context),
-				guest_cpuid_is_amd_or_hygon(vcpu));
+				guest_cpuid_is_amd_compatible(vcpu));
 }
 
 static void
@@ -4679,6 +4683,7 @@
 		/* PKEY and LA57 are active iff long mode is active. */
 		ext.cr4_pke = ____is_efer_lma(regs) && ____is_cr4_pke(regs);
 		ext.cr4_la57 = ____is_efer_lma(regs) && ____is_cr4_la57(regs);
+		ext.efer_lma = ____is_efer_lma(regs);
 	}
 
 	ext.valid = 1;
@@ -4851,7 +4856,7 @@
 	struct kvm_mmu *context = &vcpu->arch.guest_mmu;
 	struct kvm_mmu_role_regs regs = {
 		.cr0 = cr0,
-		.cr4 = cr4,
+		.cr4 = cr4 & ~X86_CR4_PKE,
 		.efer = efer,
 	};
 	union kvm_mmu_role new_role;
@@ -4915,7 +4920,7 @@
 	context->direct_map = false;
 
 	update_permission_bitmask(context, true);
-	update_pkru_bitmask(context);
+	context->pkru_mask = 0;
 	reset_rsvds_bits_mask_ept(vcpu, context, execonly);
 	reset_ept_shadow_zero_bits_mask(vcpu, context, execonly);
 }
@@ -5368,7 +5373,7 @@
 
 void kvm_mmu_invlpg(struct kvm_vcpu *vcpu, gva_t gva)
 {
-	kvm_mmu_invalidate_gva(vcpu, vcpu->arch.mmu, gva, INVALID_PAGE);
+	kvm_mmu_invalidate_gva(vcpu, vcpu->arch.walk_mmu, gva, INVALID_PAGE);
 	++vcpu->stat.invlpg;
 }
 EXPORT_SYMBOL_GPL(kvm_mmu_invlpg);
@@ -5381,14 +5386,16 @@
 	uint i;
 
 	if (pcid == kvm_get_active_pcid(vcpu)) {
-		mmu->invlpg(vcpu, gva, mmu->root_hpa);
+		if (mmu->invlpg)
+			mmu->invlpg(vcpu, gva, mmu->root_hpa);
 		tlb_flush = true;
 	}
 
 	for (i = 0; i < KVM_MMU_NUM_PREV_ROOTS; i++) {
 		if (VALID_PAGE(mmu->prev_roots[i].hpa) &&
 		    pcid == kvm_get_pcid(vcpu, mmu->prev_roots[i].pgd)) {
-			mmu->invlpg(vcpu, gva, mmu->prev_roots[i].hpa);
+			if (mmu->invlpg)
+				mmu->invlpg(vcpu, gva, mmu->prev_roots[i].hpa);
 			tlb_flush = true;
 		}
 	}
@@ -5473,8 +5480,8 @@
 }
 
 static __always_inline bool
-slot_handle_leaf(struct kvm *kvm, const struct kvm_memory_slot *memslot,
-		 slot_level_handler fn, bool flush_on_yield)
+slot_handle_level_4k(struct kvm *kvm, const struct kvm_memory_slot *memslot,
+		     slot_level_handler fn, bool flush_on_yield)
 {
 	return slot_handle_level(kvm, memslot, fn, PG_LEVEL_4K,
 				 PG_LEVEL_4K, flush_on_yield);
@@ -5575,6 +5582,7 @@
 {
 	struct kvm_mmu_page *sp, *node;
 	int nr_zapped, batch = 0;
+	bool unstable;
 
 restart:
 	list_for_each_entry_safe_reverse(sp, node,
@@ -5606,11 +5614,12 @@
 			goto restart;
 		}
 
-		if (__kvm_mmu_prepare_zap_page(kvm, sp,
-				&kvm->arch.zapped_obsolete_pages, &nr_zapped)) {
-			batch += nr_zapped;
+		unstable = __kvm_mmu_prepare_zap_page(kvm, sp,
+				&kvm->arch.zapped_obsolete_pages, &nr_zapped);
+		batch += nr_zapped;
+
+		if (unstable)
 			goto restart;
-		}
 	}
 
 	/*
@@ -5758,13 +5767,11 @@
 		for (i = 0; i < KVM_ADDRESS_SPACE_NUM; i++)
 			flush = kvm_tdp_mmu_zap_gfn_range(kvm, i, gfn_start,
 							  gfn_end, flush);
-		if (flush)
-			kvm_flush_remote_tlbs_with_address(kvm, gfn_start,
-							   gfn_end - gfn_start);
 	}
 
 	if (flush)
-		kvm_flush_remote_tlbs_with_address(kvm, gfn_start, gfn_end);
+		kvm_flush_remote_tlbs_with_address(kvm, gfn_start,
+						   gfn_end - gfn_start);
 
 	kvm_dec_notifier_count(kvm, gfn_start, gfn_end);
 
@@ -5856,21 +5863,21 @@
 void kvm_mmu_zap_collapsible_sptes(struct kvm *kvm,
 				   const struct kvm_memory_slot *slot)
 {
-	bool flush = false;
-
 	if (kvm_memslots_have_rmaps(kvm)) {
 		write_lock(&kvm->mmu_lock);
-		flush = slot_handle_leaf(kvm, slot, kvm_mmu_zap_collapsible_spte, true);
-		if (flush)
+		/*
+		 * Zap only 4k SPTEs since the legacy MMU only supports dirty
+		 * logging at a 4k granularity and never creates collapsible
+		 * 2m SPTEs during dirty logging.
+		 */
+		if (slot_handle_level_4k(kvm, slot, kvm_mmu_zap_collapsible_spte, true))
 			kvm_arch_flush_remote_tlbs_memslot(kvm, slot);
 		write_unlock(&kvm->mmu_lock);
 	}
 
 	if (is_tdp_mmu_enabled(kvm)) {
 		read_lock(&kvm->mmu_lock);
-		flush = kvm_tdp_mmu_zap_collapsible_sptes(kvm, slot, flush);
-		if (flush)
-			kvm_arch_flush_remote_tlbs_memslot(kvm, slot);
+		kvm_tdp_mmu_zap_collapsible_sptes(kvm, slot);
 		read_unlock(&kvm->mmu_lock);
 	}
 }
@@ -5897,8 +5904,11 @@
 
 	if (kvm_memslots_have_rmaps(kvm)) {
 		write_lock(&kvm->mmu_lock);
-		flush = slot_handle_leaf(kvm, memslot, __rmap_clear_dirty,
-					 false);
+		/*
+		 * Clear dirty bits only on 4k SPTEs since the legacy MMU only
+		 * support dirty logging at a 4k granularity.
+		 */
+		flush = slot_handle_level_4k(kvm, memslot, __rmap_clear_dirty, false);
 		write_unlock(&kvm->mmu_lock);
 	}
 
@@ -6091,12 +6101,24 @@
 	return 0;
 }
 
-int kvm_mmu_module_init(void)
+/*
+ * nx_huge_pages needs to be resolved to true/false when kvm.ko is loaded, as
+ * its default value of -1 is technically undefined behavior for a boolean.
+ */
+void __init kvm_mmu_x86_module_init(void)
 {
-	int ret = -ENOMEM;
-
 	if (nx_huge_pages == -1)
 		__set_nx_huge_pages(get_nx_auto_mode());
+}
+
+/*
+ * The bulk of the MMU initialization is deferred until the vendor module is
+ * loaded as many of the masks/values may be modified by VMX or SVM, i.e. need
+ * to be reset when a potentially different vendor module is loaded.
+ */
+int kvm_mmu_vendor_module_init(void)
+{
+	int ret = -ENOMEM;
 
 	/*
 	 * MMU roles use union aliasing which is, generally speaking, an
@@ -6168,7 +6190,7 @@
 	mmu_free_memory_caches(vcpu);
 }
 
-void kvm_mmu_module_exit(void)
+void kvm_mmu_vendor_module_exit(void)
 {
 	mmu_destroy_caches();
 	percpu_counter_destroy(&kvm_total_used_mmu_pages);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/page_track.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/page_track.c
@@ -36,8 +36,8 @@
 
 	for (i = 0; i < KVM_PAGE_TRACK_MAX; i++) {
 		slot->arch.gfn_track[i] =
-			kvcalloc(npages, sizeof(*slot->arch.gfn_track[i]),
-				 GFP_KERNEL_ACCOUNT);
+			__vcalloc(npages, sizeof(*slot->arch.gfn_track[i]),
+				  GFP_KERNEL_ACCOUNT);
 		if (!slot->arch.gfn_track[i])
 			goto track_free;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/paging_tmpl.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/paging_tmpl.h
@@ -34,9 +34,8 @@
 	#define PT_HAVE_ACCESSED_DIRTY(mmu) true
 	#ifdef CONFIG_X86_64
 	#define PT_MAX_FULL_LEVELS PT64_ROOT_MAX_LEVEL
-	#define CMPXCHG cmpxchg
+	#define CMPXCHG "cmpxchgq"
 	#else
-	#define CMPXCHG cmpxchg64
 	#define PT_MAX_FULL_LEVELS 2
 	#endif
 #elif PTTYPE == 32
@@ -52,7 +51,7 @@
 	#define PT_GUEST_DIRTY_SHIFT PT_DIRTY_SHIFT
 	#define PT_GUEST_ACCESSED_SHIFT PT_ACCESSED_SHIFT
 	#define PT_HAVE_ACCESSED_DIRTY(mmu) true
-	#define CMPXCHG cmpxchg
+	#define CMPXCHG "cmpxchgl"
 #elif PTTYPE == PTTYPE_EPT
 	#define pt_element_t u64
 	#define guest_walker guest_walkerEPT
@@ -65,7 +64,9 @@
 	#define PT_GUEST_DIRTY_SHIFT 9
 	#define PT_GUEST_ACCESSED_SHIFT 8
 	#define PT_HAVE_ACCESSED_DIRTY(mmu) ((mmu)->ept_ad)
-	#define CMPXCHG cmpxchg64
+	#ifdef CONFIG_X86_64
+	#define CMPXCHG "cmpxchgq"
+	#endif
 	#define PT_MAX_FULL_LEVELS PT64_ROOT_MAX_LEVEL
 #else
 	#error Invalid PTTYPE value
@@ -147,43 +148,39 @@
 			       pt_element_t __user *ptep_user, unsigned index,
 			       pt_element_t orig_pte, pt_element_t new_pte)
 {
-	int npages;
-	pt_element_t ret;
-	pt_element_t *table;
-	struct page *page;
-
-	npages = get_user_pages_fast((unsigned long)ptep_user, 1, FOLL_WRITE, &page);
-	if (likely(npages == 1)) {
-		table = kmap_atomic(page);
-		ret = CMPXCHG(&table[index], orig_pte, new_pte);
-		kunmap_atomic(table);
-
-		kvm_release_page_dirty(page);
-	} else {
-		struct vm_area_struct *vma;
-		unsigned long vaddr = (unsigned long)ptep_user & PAGE_MASK;
-		unsigned long pfn;
-		unsigned long paddr;
-
-		mmap_read_lock(current->mm);
-		vma = find_vma_intersection(current->mm, vaddr, vaddr + PAGE_SIZE);
-		if (!vma || !(vma->vm_flags & VM_PFNMAP)) {
-			mmap_read_unlock(current->mm);
-			return -EFAULT;
-		}
-		pfn = ((vaddr - vma->vm_start) >> PAGE_SHIFT) + vma->vm_pgoff;
-		paddr = pfn << PAGE_SHIFT;
-		table = memremap(paddr, PAGE_SIZE, MEMREMAP_WB);
-		if (!table) {
-			mmap_read_unlock(current->mm);
-			return -EFAULT;
-		}
-		ret = CMPXCHG(&table[index], orig_pte, new_pte);
-		memunmap(table);
-		mmap_read_unlock(current->mm);
-	}
+	int r = -EFAULT;
+
+	if (!user_access_begin(ptep_user, sizeof(pt_element_t)))
+		return -EFAULT;
+
+#ifdef CMPXCHG
+	asm volatile("1:" LOCK_PREFIX CMPXCHG " %[new], %[ptr]\n"
+		     "mov $0, %[r]\n"
+		     "setnz %b[r]\n"
+		     "2:"
+		     _ASM_EXTABLE_UA(1b, 2b)
+		     : [ptr] "+m" (*ptep_user),
+		       [old] "+a" (orig_pte),
+		       [r] "+q" (r)
+		     : [new] "r" (new_pte)
+		     : "memory");
+#else
+	asm volatile("1:" LOCK_PREFIX "cmpxchg8b %[ptr]\n"
+		     "movl $0, %[r]\n"
+		     "jz 2f\n"
+		     "incl %[r]\n"
+		     "2:"
+		     _ASM_EXTABLE_UA(1b, 2b)
+		     : [ptr] "+m" (*ptep_user),
+		       [old] "+A" (orig_pte),
+		       [r] "+rm" (r)
+		     : [new_lo] "b" ((u32)new_pte),
+		       [new_hi] "c" ((u32)(new_pte >> 32))
+		     : "memory");
+#endif
 
-	return (ret != orig_pte);
+	user_access_end();
+	return r;
 }
 
 static bool FNAME(prefetch_invalid_gpte)(struct kvm_vcpu *vcpu,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/spte.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/spte.h
@@ -310,12 +310,7 @@
 static __always_inline bool is_rsvd_spte(struct rsvd_bits_validate *rsvd_check,
 					 u64 spte, int level)
 {
-	/*
-	 * Use a bitwise-OR instead of a logical-OR to aggregate the reserved
-	 * bits and EPT's invalid memtype/XWR checks to avoid an extra Jcc
-	 * (this is extremely unlikely to be short-circuited as true).
-	 */
-	return __is_bad_mt_xwr(rsvd_check, spte) |
+	return __is_bad_mt_xwr(rsvd_check, spte) ||
 	       __is_rsvd_bits_set(rsvd_check, spte, level);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/tdp_iter.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/tdp_iter.c
@@ -26,6 +26,7 @@
  */
 void tdp_iter_restart(struct tdp_iter *iter)
 {
+	iter->yielded = false;
 	iter->yielded_gfn = iter->next_last_level_gfn;
 	iter->level = iter->root_level;
 
@@ -160,6 +161,11 @@
  */
 void tdp_iter_next(struct tdp_iter *iter)
 {
+	if (iter->yielded) {
+		tdp_iter_restart(iter);
+		return;
+	}
+
 	if (try_step_down(iter))
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/tdp_iter.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/tdp_iter.h
@@ -45,6 +45,12 @@
 	 * iterator walks off the end of the paging structure.
 	 */
 	bool valid;
+	/*
+	 * True if KVM dropped mmu_lock and yielded in the middle of a walk, in
+	 * which case tdp_iter_next() needs to restart the walk at the root
+	 * level instead of advancing to the next entry.
+	 */
+	bool yielded;
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/tdp_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/tdp_mmu.c
@@ -10,7 +10,7 @@
 #include <asm/cmpxchg.h>
 #include <trace/events/kvm.h>
 
-static bool __read_mostly tdp_mmu_enabled = true;
+static bool __read_mostly tdp_mmu_enabled = false;
 module_param_named(tdp_mmu, tdp_mmu_enabled, bool, 0644);
 
 /* Initializes the TDP MMU for the VM, if enabled. */
@@ -24,7 +24,6 @@
 
 	INIT_LIST_HEAD(&kvm->arch.tdp_mmu_roots);
 	spin_lock_init(&kvm->arch.tdp_mmu_pages_lock);
-	INIT_LIST_HEAD(&kvm->arch.tdp_mmu_pages);
 
 	return true;
 }
@@ -43,7 +42,7 @@
 	if (!kvm->arch.tdp_mmu_enabled)
 		return;
 
-	WARN_ON(!list_empty(&kvm->arch.tdp_mmu_pages));
+	WARN_ON(atomic64_read(&kvm->arch.tdp_mmu_pages));
 	WARN_ON(!list_empty(&kvm->arch.tdp_mmu_roots));
 
 	/*
@@ -99,15 +98,18 @@
 }
 
 /*
- * Finds the next valid root after root (or the first valid root if root
- * is NULL), takes a reference on it, and returns that next root. If root
- * is not NULL, this thread should have already taken a reference on it, and
- * that reference will be dropped. If no valid root is found, this
- * function will return NULL.
+ * Returns the next root after @prev_root (or the first root if @prev_root is
+ * NULL).  A reference to the returned root is acquired, and the reference to
+ * @prev_root is released (the caller obviously must hold a reference to
+ * @prev_root if it's non-NULL).
+ *
+ * If @only_valid is true, invalid roots are skipped.
+ *
+ * Returns NULL if the end of tdp_mmu_roots was reached.
  */
 static struct kvm_mmu_page *tdp_mmu_next_root(struct kvm *kvm,
 					      struct kvm_mmu_page *prev_root,
-					      bool shared)
+					      bool shared, bool only_valid)
 {
 	struct kvm_mmu_page *next_root;
 
@@ -121,9 +123,14 @@
 		next_root = list_first_or_null_rcu(&kvm->arch.tdp_mmu_roots,
 						   typeof(*next_root), link);
 
-	while (next_root && !kvm_tdp_mmu_get_root(kvm, next_root))
+	while (next_root) {
+		if ((!only_valid || !next_root->role.invalid) &&
+		    kvm_tdp_mmu_get_root(kvm, next_root))
+			break;
+
 		next_root = list_next_or_null_rcu(&kvm->arch.tdp_mmu_roots,
 				&next_root->link, typeof(*next_root), link);
+	}
 
 	rcu_read_unlock();
 
@@ -143,13 +150,19 @@
  * mode. In the unlikely event that this thread must free a root, the lock
  * will be temporarily dropped and reacquired in write mode.
  */
-#define for_each_tdp_mmu_root_yield_safe(_kvm, _root, _as_id, _shared)	\
-	for (_root = tdp_mmu_next_root(_kvm, NULL, _shared);		\
-	     _root;							\
-	     _root = tdp_mmu_next_root(_kvm, _root, _shared))		\
-		if (kvm_mmu_page_as_id(_root) != _as_id) {		\
+#define __for_each_tdp_mmu_root_yield_safe(_kvm, _root, _as_id, _shared, _only_valid)\
+	for (_root = tdp_mmu_next_root(_kvm, NULL, _shared, _only_valid);	\
+	     _root;								\
+	     _root = tdp_mmu_next_root(_kvm, _root, _shared, _only_valid))	\
+		if (kvm_mmu_page_as_id(_root) != _as_id) {			\
 		} else
 
+#define for_each_valid_tdp_mmu_root_yield_safe(_kvm, _root, _as_id, _shared)	\
+	__for_each_tdp_mmu_root_yield_safe(_kvm, _root, _as_id, _shared, true)
+
+#define for_each_tdp_mmu_root_yield_safe(_kvm, _root, _as_id, _shared)		\
+	__for_each_tdp_mmu_root_yield_safe(_kvm, _root, _as_id, _shared, false)
+
 #define for_each_tdp_mmu_root(_kvm, _root, _as_id)				\
 	list_for_each_entry_rcu(_root, &_kvm->arch.tdp_mmu_roots, link,		\
 				lockdep_is_held_type(&kvm->mmu_lock, 0) ||	\
@@ -199,7 +212,10 @@
 
 	role = page_role_for_level(vcpu, vcpu->arch.mmu->shadow_root_level);
 
-	/* Check for an existing root before allocating a new one. */
+	/*
+	 * Check for an existing root before allocating a new one.  Note, the
+	 * role check prevents consuming an invalid root.
+	 */
 	for_each_tdp_mmu_root(kvm, root, kvm_mmu_role_as_id(role)) {
 		if (root->role.word == role.word &&
 		    kvm_tdp_mmu_get_root(kvm, root))
@@ -261,11 +277,12 @@
 static void tdp_mmu_link_page(struct kvm *kvm, struct kvm_mmu_page *sp,
 			      bool account_nx)
 {
-	spin_lock(&kvm->arch.tdp_mmu_pages_lock);
-	list_add(&sp->link, &kvm->arch.tdp_mmu_pages);
-	if (account_nx)
+	atomic64_inc(&kvm->arch.tdp_mmu_pages);
+	if (account_nx) {
+		spin_lock(&kvm->arch.tdp_mmu_pages_lock);
 		account_huge_nx_page(kvm, sp);
-	spin_unlock(&kvm->arch.tdp_mmu_pages_lock);
+		spin_unlock(&kvm->arch.tdp_mmu_pages_lock);
+	}
 }
 
 /**
@@ -280,14 +297,16 @@
 static void tdp_mmu_unlink_page(struct kvm *kvm, struct kvm_mmu_page *sp,
 				bool shared)
 {
+	atomic64_dec(&kvm->arch.tdp_mmu_pages);
+	if (!sp->lpage_disallowed)
+		return;
+
 	if (shared)
 		spin_lock(&kvm->arch.tdp_mmu_pages_lock);
 	else
 		lockdep_assert_held_write(&kvm->mmu_lock);
 
-	list_del(&sp->link);
-	if (sp->lpage_disallowed)
-		unaccount_huge_nx_page(kvm, sp);
+	unaccount_huge_nx_page(kvm, sp);
 
 	if (shared)
 		spin_unlock(&kvm->arch.tdp_mmu_pages_lock);
@@ -316,9 +335,6 @@
 	struct kvm_mmu_page *sp = sptep_to_sp(rcu_dereference(pt));
 	int level = sp->role.level;
 	gfn_t base_gfn = sp->gfn;
-	u64 old_child_spte;
-	u64 *sptep;
-	gfn_t gfn;
 	int i;
 
 	trace_kvm_mmu_prepare_zap_page(sp);
@@ -326,8 +342,9 @@
 	tdp_mmu_unlink_page(kvm, sp, shared);
 
 	for (i = 0; i < PT64_ENT_PER_PAGE; i++) {
-		sptep = rcu_dereference(pt) + i;
-		gfn = base_gfn + i * KVM_PAGES_PER_HPAGE(level);
+		u64 *sptep = rcu_dereference(pt) + i;
+		gfn_t gfn = base_gfn + i * KVM_PAGES_PER_HPAGE(level);
+		u64 old_child_spte;
 
 		if (shared) {
 			/*
@@ -373,7 +390,7 @@
 				    shared);
 	}
 
-	kvm_flush_remote_tlbs_with_address(kvm, gfn,
+	kvm_flush_remote_tlbs_with_address(kvm, base_gfn,
 					   KVM_PAGES_PER_HPAGE(level + 1));
 
 	call_rcu(&sp->rcu_head, tdp_mmu_free_sp_rcu_callback);
@@ -503,6 +520,8 @@
 							struct tdp_iter *iter,
 							u64 new_spte)
 {
+	WARN_ON_ONCE(iter->yielded);
+
 	lockdep_assert_held_read(&kvm->mmu_lock);
 
 	/*
@@ -613,6 +632,8 @@
 				      u64 new_spte, bool record_acc_track,
 				      bool record_dirty_log)
 {
+	WARN_ON_ONCE(iter->yielded);
+
 	lockdep_assert_held_write(&kvm->mmu_lock);
 
 	/*
@@ -678,18 +699,19 @@
  * If this function should yield and flush is set, it will perform a remote
  * TLB flush before yielding.
  *
- * If this function yields, it will also reset the tdp_iter's walk over the
- * paging structure and the calling function should skip to the next
- * iteration to allow the iterator to continue its traversal from the
- * paging structure root.
+ * If this function yields, iter->yielded is set and the caller must skip to
+ * the next iteration, where tdp_iter_next() will reset the tdp_iter's walk
+ * over the paging structures to allow the iterator to continue its traversal
+ * from the paging structure root.
  *
- * Return true if this function yielded and the iterator's traversal was reset.
- * Return false if a yield was not needed.
+ * Returns true if this function yielded.
  */
-static inline bool tdp_mmu_iter_cond_resched(struct kvm *kvm,
-					     struct tdp_iter *iter, bool flush,
-					     bool shared)
+static inline bool __must_check tdp_mmu_iter_cond_resched(struct kvm *kvm,
+							  struct tdp_iter *iter,
+							  bool flush, bool shared)
 {
+	WARN_ON(iter->yielded);
+
 	/* Ensure forward progress has been made before yielding. */
 	if (iter->next_last_level_gfn == iter->yielded_gfn)
 		return false;
@@ -709,12 +731,10 @@
 
 		WARN_ON(iter->gfn > iter->next_last_level_gfn);
 
-		tdp_iter_restart(iter);
-
-		return true;
+		iter->yielded = true;
 	}
 
-	return false;
+	return iter->yielded;
 }
 
 /*
@@ -1080,13 +1100,8 @@
 bool kvm_tdp_mmu_unmap_gfn_range(struct kvm *kvm, struct kvm_gfn_range *range,
 				 bool flush)
 {
-	struct kvm_mmu_page *root;
-
-	for_each_tdp_mmu_root(kvm, root, range->slot->as_id)
-		flush |= zap_gfn_range(kvm, root, range->start, range->end,
-				       range->may_block, flush, false);
-
-	return flush;
+	return __kvm_tdp_mmu_zap_gfn_range(kvm, range->slot->as_id, range->start,
+					   range->end, range->may_block, flush);
 }
 
 typedef bool (*tdp_handler_t)(struct kvm *kvm, struct tdp_iter *iter,
@@ -1270,7 +1285,7 @@
 
 	lockdep_assert_held_read(&kvm->mmu_lock);
 
-	for_each_tdp_mmu_root_yield_safe(kvm, root, slot->as_id, true)
+	for_each_valid_tdp_mmu_root_yield_safe(kvm, root, slot->as_id, true)
 		spte_set |= wrprot_gfn_range(kvm, root, slot->base_gfn,
 			     slot->base_gfn + slot->npages, min_level);
 
@@ -1298,6 +1313,9 @@
 		if (tdp_mmu_iter_cond_resched(kvm, &iter, false, true))
 			continue;
 
+		if (!is_shadow_present_pte(iter.old_spte))
+			continue;
+
 		if (spte_ad_need_write_protect(iter.old_spte)) {
 			if (is_writable_pte(iter.old_spte))
 				new_spte = iter.old_spte & ~PT_WRITABLE_MASK;
@@ -1341,7 +1359,7 @@
 
 	lockdep_assert_held_read(&kvm->mmu_lock);
 
-	for_each_tdp_mmu_root_yield_safe(kvm, root, slot->as_id, true)
+	for_each_valid_tdp_mmu_root_yield_safe(kvm, root, slot->as_id, true)
 		spte_set |= clear_dirty_gfn_range(kvm, root, slot->base_gfn,
 				slot->base_gfn + slot->npages);
 
@@ -1415,10 +1433,9 @@
  * Clear leaf entries which could be replaced by large mappings, for
  * GFNs within the slot.
  */
-static bool zap_collapsible_spte_range(struct kvm *kvm,
+static void zap_collapsible_spte_range(struct kvm *kvm,
 				       struct kvm_mmu_page *root,
-				       const struct kvm_memory_slot *slot,
-				       bool flush)
+				       const struct kvm_memory_slot *slot)
 {
 	gfn_t start = slot->base_gfn;
 	gfn_t end = start + slot->npages;
@@ -1429,10 +1446,8 @@
 
 	tdp_root_for_each_pte(iter, root, start, end) {
 retry:
-		if (tdp_mmu_iter_cond_resched(kvm, &iter, flush, true)) {
-			flush = false;
+		if (tdp_mmu_iter_cond_resched(kvm, &iter, false, true))
 			continue;
-		}
 
 		if (!is_shadow_present_pte(iter.old_spte) ||
 		    !is_last_spte(iter.old_spte, iter.level))
@@ -1444,6 +1459,7 @@
 							    pfn, PG_LEVEL_NUM))
 			continue;
 
+		/* Note, a successful atomic zap also does a remote TLB flush. */
 		if (!tdp_mmu_zap_spte_atomic(kvm, &iter)) {
 			/*
 			 * The iter must explicitly re-read the SPTE because
@@ -1452,30 +1468,24 @@
 			iter.old_spte = READ_ONCE(*rcu_dereference(iter.sptep));
 			goto retry;
 		}
-		flush = true;
 	}
 
 	rcu_read_unlock();
-
-	return flush;
 }
 
 /*
  * Clear non-leaf entries (and free associated page tables) which could
  * be replaced by large mappings, for GFNs within the slot.
  */
-bool kvm_tdp_mmu_zap_collapsible_sptes(struct kvm *kvm,
-				       const struct kvm_memory_slot *slot,
-				       bool flush)
+void kvm_tdp_mmu_zap_collapsible_sptes(struct kvm *kvm,
+				       const struct kvm_memory_slot *slot)
 {
 	struct kvm_mmu_page *root;
 
 	lockdep_assert_held_read(&kvm->mmu_lock);
 
-	for_each_tdp_mmu_root_yield_safe(kvm, root, slot->as_id, true)
-		flush = zap_collapsible_spte_range(kvm, root, slot, flush);
-
-	return flush;
+	for_each_valid_tdp_mmu_root_yield_safe(kvm, root, slot->as_id, true)
+		zap_collapsible_spte_range(kvm, root, slot);
 }
 
 /*
@@ -1500,12 +1510,12 @@
 		    !is_last_spte(iter.old_spte, iter.level))
 			continue;
 
-		if (!is_writable_pte(iter.old_spte))
-			break;
-
 		new_spte = iter.old_spte &
 			~(PT_WRITABLE_MASK | shadow_mmu_writable_mask);
 
+		if (new_spte == iter.old_spte)
+			break;
+
 		tdp_mmu_set_spte(kvm, &iter, new_spte);
 		spte_set = true;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/mmu/tdp_mmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/mmu/tdp_mmu.h
@@ -10,9 +10,6 @@
 __must_check static inline bool kvm_tdp_mmu_get_root(struct kvm *kvm,
 						     struct kvm_mmu_page *root)
 {
-	if (root->role.invalid)
-		return false;
-
 	return refcount_inc_not_zero(&root->tdp_mmu_root_count);
 }
 
@@ -66,9 +63,8 @@
 				       struct kvm_memory_slot *slot,
 				       gfn_t gfn, unsigned long mask,
 				       bool wrprot);
-bool kvm_tdp_mmu_zap_collapsible_sptes(struct kvm *kvm,
-				       const struct kvm_memory_slot *slot,
-				       bool flush);
+void kvm_tdp_mmu_zap_collapsible_sptes(struct kvm *kvm,
+				       const struct kvm_memory_slot *slot);
 
 bool kvm_tdp_mmu_write_protect_gfn(struct kvm *kvm,
 				   struct kvm_memory_slot *slot, gfn_t gfn,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/pmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/pmu.c
@@ -95,9 +95,8 @@
 }
 
 static void pmc_reprogram_counter(struct kvm_pmc *pmc, u32 type,
-				  unsigned config, bool exclude_user,
-				  bool exclude_kernel, bool intr,
-				  bool in_tx, bool in_tx_cp)
+				  u64 config, bool exclude_user,
+				  bool exclude_kernel, bool intr)
 {
 	struct perf_event *event;
 	struct perf_event_attr attr = {
@@ -113,16 +112,14 @@
 
 	attr.sample_period = get_sample_period(pmc, pmc->counter);
 
-	if (in_tx)
-		attr.config |= HSW_IN_TX;
-	if (in_tx_cp) {
+	if ((attr.config & HSW_IN_TX_CHECKPOINTED) &&
+	    guest_cpuid_is_intel(pmc->vcpu)) {
 		/*
 		 * HSW_IN_TX_CHECKPOINTED is not supported with nonzero
 		 * period. Just clear the sample period so at least
 		 * allocating the counter doesn't fail.
 		 */
 		attr.sample_period = 0;
-		attr.config |= HSW_IN_TX_CHECKPOINTED;
 	}
 
 	event = perf_event_create_kernel_counter(&attr, -1, current,
@@ -173,11 +170,12 @@
 
 void reprogram_gp_counter(struct kvm_pmc *pmc, u64 eventsel)
 {
-	unsigned config, type = PERF_TYPE_RAW;
-	u8 event_select, unit_mask;
+	u64 config;
+	u32 type = PERF_TYPE_RAW;
 	struct kvm *kvm = pmc->vcpu->kvm;
 	struct kvm_pmu_event_filter *filter;
 	int i;
+	struct kvm_pmu *pmu = vcpu_to_pmu(pmc->vcpu);
 	bool allow_event = true;
 
 	if (eventsel & ARCH_PERFMON_EVENTSEL_PIN_CONTROL)
@@ -206,23 +204,18 @@
 	if (!allow_event)
 		return;
 
-	event_select = eventsel & ARCH_PERFMON_EVENTSEL_EVENT;
-	unit_mask = (eventsel & ARCH_PERFMON_EVENTSEL_UMASK) >> 8;
-
 	if (!(eventsel & (ARCH_PERFMON_EVENTSEL_EDGE |
 			  ARCH_PERFMON_EVENTSEL_INV |
 			  ARCH_PERFMON_EVENTSEL_CMASK |
 			  HSW_IN_TX |
 			  HSW_IN_TX_CHECKPOINTED))) {
-		config = kvm_x86_ops.pmu_ops->find_arch_event(pmc_to_pmu(pmc),
-						      event_select,
-						      unit_mask);
+		config = kvm_x86_ops.pmu_ops->pmc_perf_hw_id(pmc);
 		if (config != PERF_COUNT_HW_MAX)
 			type = PERF_TYPE_HARDWARE;
 	}
 
 	if (type == PERF_TYPE_RAW)
-		config = eventsel & X86_RAW_EVENT_MASK;
+		config = eventsel & pmu->raw_event_mask;
 
 	if (pmc->current_config == eventsel && pmc_resume_counter(pmc))
 		return;
@@ -233,9 +226,7 @@
 	pmc_reprogram_counter(pmc, type, config,
 			      !(eventsel & ARCH_PERFMON_EVENTSEL_USR),
 			      !(eventsel & ARCH_PERFMON_EVENTSEL_OS),
-			      eventsel & ARCH_PERFMON_EVENTSEL_INT,
-			      (eventsel & HSW_IN_TX),
-			      (eventsel & HSW_IN_TX_CHECKPOINTED));
+			      eventsel & ARCH_PERFMON_EVENTSEL_INT);
 }
 EXPORT_SYMBOL_GPL(reprogram_gp_counter);
 
@@ -271,7 +262,7 @@
 			      kvm_x86_ops.pmu_ops->find_fixed_event(idx),
 			      !(en_field & 0x2), /* exclude user */
 			      !(en_field & 0x1), /* exclude kernel */
-			      pmi, false, false);
+			      pmi);
 }
 EXPORT_SYMBOL_GPL(reprogram_fixed_counter);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/pmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/pmu.h
@@ -24,8 +24,7 @@
 };
 
 struct kvm_pmu_ops {
-	unsigned (*find_arch_event)(struct kvm_pmu *pmu, u8 event_select,
-				    u8 unit_mask);
+	unsigned int (*pmc_perf_hw_id)(struct kvm_pmc *pmc);
 	unsigned (*find_fixed_event)(int idx);
 	bool (*pmc_is_enabled)(struct kvm_pmc *pmc);
 	struct kvm_pmc *(*pmc_idx_to_pmc)(struct kvm_pmu *pmu, int pmc_idx);
@@ -142,6 +141,15 @@
 	return sample_period;
 }
 
+static inline void pmc_update_sample_period(struct kvm_pmc *pmc)
+{
+	if (!pmc->perf_event || pmc->is_paused)
+		return;
+
+	perf_event_period(pmc->perf_event,
+			  get_sample_period(pmc, pmc->counter));
+}
+
 void reprogram_gp_counter(struct kvm_pmc *pmc, u64 eventsel);
 void reprogram_fixed_counter(struct kvm_pmc *pmc, u8 ctrl, int fixed_idx);
 void reprogram_counter(struct kvm_pmu *pmu, int pmc_idx);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/reverse_cpuid.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/reverse_cpuid.h
@@ -7,23 +7,44 @@
 #include <asm/cpufeatures.h>
 
 /*
- * Hardware-defined CPUID leafs that are scattered in the kernel, but need to
- * be directly used by KVM.  Note, these word values conflict with the kernel's
- * "bug" caps, but KVM doesn't use those.
+ * Hardware-defined CPUID leafs that are either scattered by the kernel or are
+ * unknown to the kernel, but need to be directly used by KVM.  Note, these
+ * word values conflict with the kernel's "bug" caps, but KVM doesn't use those.
  */
 enum kvm_only_cpuid_leafs {
 	CPUID_12_EAX	 = NCAPINTS,
+	CPUID_7_2_EDX,
 	NR_KVM_CPU_CAPS,
 
 	NKVMCAPINTS = NR_KVM_CPU_CAPS - NCAPINTS,
 };
 
+/*
+ * Define a KVM-only feature flag.
+ *
+ * For features that are scattered by cpufeatures.h, __feature_translate() also
+ * needs to be updated to translate the kernel-defined feature into the
+ * KVM-defined feature.
+ *
+ * For features that are 100% KVM-only, i.e. not defined by cpufeatures.h,
+ * forego the intermediate KVM_X86_FEATURE and directly define X86_FEATURE_* so
+ * that X86_FEATURE_* can be used in KVM.  No __feature_translate() handling is
+ * needed in this case.
+ */
 #define KVM_X86_FEATURE(w, f)		((w)*32 + (f))
 
 /* Intel-defined SGX sub-features, CPUID level 0x12 (EAX). */
 #define KVM_X86_FEATURE_SGX1		KVM_X86_FEATURE(CPUID_12_EAX, 0)
 #define KVM_X86_FEATURE_SGX2		KVM_X86_FEATURE(CPUID_12_EAX, 1)
 
+/* Intel-defined sub-features, CPUID level 0x00000007:2 (EDX) */
+#define X86_FEATURE_INTEL_PSFD		KVM_X86_FEATURE(CPUID_7_2_EDX, 0)
+#define X86_FEATURE_IPRED_CTRL		KVM_X86_FEATURE(CPUID_7_2_EDX, 1)
+#define KVM_X86_FEATURE_RRSBA_CTRL	KVM_X86_FEATURE(CPUID_7_2_EDX, 2)
+#define X86_FEATURE_DDPD_U		KVM_X86_FEATURE(CPUID_7_2_EDX, 3)
+#define KVM_X86_FEATURE_BHI_CTRL	KVM_X86_FEATURE(CPUID_7_2_EDX, 4)
+#define X86_FEATURE_MCDT_NO		KVM_X86_FEATURE(CPUID_7_2_EDX, 5)
+
 struct cpuid_reg {
 	u32 function;
 	u32 index;
@@ -48,6 +69,8 @@
 	[CPUID_7_1_EAX]       = {         7, 1, CPUID_EAX},
 	[CPUID_12_EAX]        = {0x00000012, 0, CPUID_EAX},
 	[CPUID_8000_001F_EAX] = {0x8000001f, 0, CPUID_EAX},
+	[CPUID_8000_0021_EAX] = {0x80000021, 0, CPUID_EAX},
+	[CPUID_7_2_EDX]       = {         7, 2, CPUID_EDX},
 };
 
 /*
@@ -60,10 +83,12 @@
  */
 static __always_inline void reverse_cpuid_check(unsigned int x86_leaf)
 {
+	BUILD_BUG_ON(NR_CPUID_WORDS != NCAPINTS);
 	BUILD_BUG_ON(x86_leaf == CPUID_LNX_1);
 	BUILD_BUG_ON(x86_leaf == CPUID_LNX_2);
 	BUILD_BUG_ON(x86_leaf == CPUID_LNX_3);
 	BUILD_BUG_ON(x86_leaf == CPUID_LNX_4);
+	BUILD_BUG_ON(x86_leaf == CPUID_LNX_5);
 	BUILD_BUG_ON(x86_leaf >= ARRAY_SIZE(reverse_cpuid));
 	BUILD_BUG_ON(reverse_cpuid[x86_leaf].function == 0);
 }
@@ -74,12 +99,17 @@
  */
 static __always_inline u32 __feature_translate(int x86_feature)
 {
-	if (x86_feature == X86_FEATURE_SGX1)
-		return KVM_X86_FEATURE_SGX1;
-	else if (x86_feature == X86_FEATURE_SGX2)
-		return KVM_X86_FEATURE_SGX2;
+#define KVM_X86_TRANSLATE_FEATURE(f)	\
+	case X86_FEATURE_##f: return KVM_X86_FEATURE_##f
 
-	return x86_feature;
+	switch (x86_feature) {
+	KVM_X86_TRANSLATE_FEATURE(SGX1);
+	KVM_X86_TRANSLATE_FEATURE(SGX2);
+	KVM_X86_TRANSLATE_FEATURE(RRSBA_CTRL);
+	KVM_X86_TRANSLATE_FEATURE(BHI_CTRL);
+	default:
+		return x86_feature;
+	}
 }
 
 static __always_inline u32 __feature_leaf(int x86_feature)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/avic.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/avic.c
@@ -318,20 +318,24 @@
 	trace_kvm_avic_incomplete_ipi(vcpu->vcpu_id, icrh, icrl, id, index);
 
 	switch (id) {
+	case AVIC_IPI_FAILURE_INVALID_TARGET:
 	case AVIC_IPI_FAILURE_INVALID_INT_TYPE:
 		/*
-		 * AVIC hardware handles the generation of
-		 * IPIs when the specified Message Type is Fixed
-		 * (also known as fixed delivery mode) and
-		 * the Trigger Mode is edge-triggered. The hardware
-		 * also supports self and broadcast delivery modes
-		 * specified via the Destination Shorthand(DSH)
-		 * field of the ICRL. Logical and physical APIC ID
-		 * formats are supported. All other IPI types cause
-		 * a #VMEXIT, which needs to emulated.
+		 * Emulate IPIs that are not handled by AVIC hardware, which
+		 * only virtualizes Fixed, Edge-Triggered INTRs, and falls over
+		 * if _any_ targets are invalid, e.g. if the logical mode mask
+		 * is a superset of running vCPUs.
+		 *
+		 * The exit is a trap, e.g. ICR holds the correct value and RIP
+		 * has been advanced, KVM is responsible only for emulating the
+		 * IPI.  Sadly, hardware may sometimes leave the BUSY flag set,
+		 * in which case KVM needs to emulate the ICR write as well in
+		 * order to clear the BUSY flag.
 		 */
-		kvm_lapic_reg_write(apic, APIC_ICR2, icrh);
-		kvm_lapic_reg_write(apic, APIC_ICR, icrl);
+		if (icrl & APIC_ICR_BUSY)
+			kvm_apic_write_nodecode(vcpu, APIC_ICR);
+		else
+			kvm_apic_send_ipi(apic, icrl, icrh);
 		break;
 	case AVIC_IPI_FAILURE_TARGET_NOT_RUNNING:
 		/*
@@ -341,10 +345,6 @@
 		 */
 		avic_kick_target_vcpus(vcpu->kvm, apic, icrl, icrh);
 		break;
-	case AVIC_IPI_FAILURE_INVALID_TARGET:
-		WARN_ONCE(1, "Invalid IPI target: index=%u, vcpu=%d, icr=%#0x:%#0x\n",
-			  index, vcpu->vcpu_id, icrh, icrl);
-		break;
 	case AVIC_IPI_FAILURE_INVALID_BACKING_PAGE:
 		WARN_ONCE(1, "Invalid backing page\n");
 		break;
@@ -801,7 +801,7 @@
 {
 	struct kvm_kernel_irq_routing_entry *e;
 	struct kvm_irq_routing_table *irq_rt;
-	int idx, ret = -EINVAL;
+	int idx, ret = 0;
 
 	if (!kvm_arch_has_assigned_device(kvm) ||
 	    !irq_remapping_cap(IRQ_POSTING_CAP))
@@ -812,7 +812,13 @@
 
 	idx = srcu_read_lock(&kvm->irq_srcu);
 	irq_rt = srcu_dereference(kvm->irq_routing, &kvm->irq_srcu);
-	WARN_ON(guest_irq >= irq_rt->nr_rt_entries);
+
+	if (guest_irq >= irq_rt->nr_rt_entries ||
+		hlist_empty(&irq_rt->map[guest_irq])) {
+		pr_warn_once("no route for guest_irq %u/%u (broken user space?)\n",
+			     guest_irq, irq_rt->nr_rt_entries);
+		goto out;
+	}
 
 	hlist_for_each_entry(e, &irq_rt->map[guest_irq], link) {
 		struct vcpu_data vcpu_info;
@@ -943,15 +949,10 @@
 void avic_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
 {
 	u64 entry;
-	/* ID = 0xff (broadcast), ID > 0xff (reserved) */
 	int h_physical_id = kvm_cpu_get_apicid(cpu);
 	struct vcpu_svm *svm = to_svm(vcpu);
 
-	/*
-	 * Since the host physical APIC id is 8 bits,
-	 * we can support host APIC ID upto 255.
-	 */
-	if (WARN_ON(h_physical_id > AVIC_PHYSICAL_ID_ENTRY_HOST_PHYSICAL_ID_MASK))
+	if (WARN_ON(h_physical_id & ~AVIC_PHYSICAL_ID_ENTRY_HOST_PHYSICAL_ID_MASK))
 		return;
 
 	entry = READ_ONCE(*(svm->avic_physical_id_cache));
@@ -988,16 +989,18 @@
 static void avic_set_running(struct kvm_vcpu *vcpu, bool is_run)
 {
 	struct vcpu_svm *svm = to_svm(vcpu);
+	int cpu = get_cpu();
 
+	WARN_ON(cpu != vcpu->cpu);
 	svm->avic_is_running = is_run;
 
-	if (!kvm_vcpu_apicv_active(vcpu))
-		return;
-
-	if (is_run)
-		avic_vcpu_load(vcpu, vcpu->cpu);
-	else
-		avic_vcpu_put(vcpu);
+	if (kvm_vcpu_apicv_active(vcpu)) {
+		if (is_run)
+			avic_vcpu_load(vcpu, cpu);
+		else
+			avic_vcpu_put(vcpu);
+	}
+	put_cpu();
 }
 
 void svm_vcpu_blocking(struct kvm_vcpu *vcpu)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/nested.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/nested.c
@@ -77,8 +77,12 @@
 	u64 pdpte;
 	int ret;
 
+	/*
+	 * Note, nCR3 is "assumed" to be 32-byte aligned, i.e. the CPU ignores
+	 * nCR3[4:0] when loading PDPTEs from memory.
+	 */
 	ret = kvm_vcpu_read_guest_page(vcpu, gpa_to_gfn(cr3), &pdpte,
-				       offset_in_page(cr3) + index * 8, 8);
+				       (cr3 & GENMASK(11, 5)) + index * 8, 8);
 	if (ret)
 		return 0;
 	return pdpte;
@@ -275,7 +279,8 @@
 			return false;
 	}
 
-	if (CC(!kvm_is_valid_cr4(vcpu, save->cr4)))
+	/* Note, SVM doesn't have any additional restrictions on CR4. */
+	if (CC(!__kvm_is_valid_cr4(vcpu, save->cr4)))
 		return false;
 
 	return true;
@@ -750,9 +755,6 @@
 	struct kvm_host_map map;
 	int rc;
 
-	/* Triple faults in L2 should never escape. */
-	WARN_ON_ONCE(kvm_check_request(KVM_REQ_TRIPLE_FAULT, vcpu));
-
 	rc = kvm_vcpu_map(vcpu, gpa_to_gfn(svm->nested.vmcb12_gpa), &map);
 	if (rc) {
 		if (rc == -EINVAL)
@@ -921,6 +923,9 @@
 	if (!svm->nested.initialized)
 		return;
 
+	if (WARN_ON_ONCE(svm->vmcb != svm->vmcb01.ptr))
+		svm_switch_vmcb(svm, &svm->vmcb01);
+
 	svm_vcpu_free_msrpm(svm->nested.msrpm);
 	svm->nested.msrpm = NULL;
 
@@ -939,12 +944,9 @@
 	svm->nested.initialized = false;
 }
 
-/*
- * Forcibly leave nested mode in order to be able to reset the VCPU later on.
- */
-void svm_leave_nested(struct vcpu_svm *svm)
+void svm_leave_nested(struct kvm_vcpu *vcpu)
 {
-	struct kvm_vcpu *vcpu = &svm->vcpu;
+	struct vcpu_svm *svm = to_svm(vcpu);
 
 	if (is_guest_mode(vcpu)) {
 		svm->nested.nested_run_pending = 0;
@@ -1313,7 +1315,7 @@
 		return -EINVAL;
 
 	if (!(kvm_state->flags & KVM_STATE_NESTED_GUEST_MODE)) {
-		svm_leave_nested(svm);
+		svm_leave_nested(vcpu);
 		svm_set_gif(svm, !!(kvm_state->flags & KVM_STATE_NESTED_GIF_SET));
 		return 0;
 	}
@@ -1357,18 +1359,6 @@
 	    !nested_vmcb_valid_sregs(vcpu, save))
 		goto out_free;
 
-	/*
-	 * While the nested guest CR3 is already checked and set by
-	 * KVM_SET_SREGS, it was set when nested state was yet loaded,
-	 * thus MMU might not be initialized correctly.
-	 * Set it again to fix this.
-	 */
-
-	ret = nested_svm_load_cr3(&svm->vcpu, vcpu->arch.cr3,
-				  nested_npt_enabled(svm), false);
-	if (WARN_ON_ONCE(ret))
-		goto out_free;
-
 
 	/*
 	 * All checks done, we can enter guest mode. Userspace provides
@@ -1378,7 +1368,7 @@
 	 */
 
 	if (is_guest_mode(vcpu))
-		svm_leave_nested(svm);
+		svm_leave_nested(vcpu);
 	else
 		svm->nested.vmcb02.ptr->save = svm->vmcb01.ptr->save;
 
@@ -1394,6 +1384,20 @@
 
 	svm_switch_vmcb(svm, &svm->nested.vmcb02);
 	nested_vmcb02_prepare_control(svm);
+
+	/*
+	 * While the nested guest CR3 is already checked and set by
+	 * KVM_SET_SREGS, it was set when nested state was yet loaded,
+	 * thus MMU might not be initialized correctly.
+	 * Set it again to fix this.
+	 */
+
+	ret = nested_svm_load_cr3(&svm->vcpu, vcpu->arch.cr3,
+				  nested_npt_enabled(svm), false);
+	if (WARN_ON_ONCE(ret))
+		goto out_free;
+
+
 	kvm_make_request(KVM_REQ_GET_NESTED_STATE_PAGES, vcpu);
 	ret = 0;
 out_free:
@@ -1432,6 +1436,7 @@
 }
 
 struct kvm_x86_nested_ops svm_nested_ops = {
+	.leave_nested = svm_leave_nested,
 	.check_events = svm_check_nested_events,
 	.triple_fault = nested_svm_triple_fault,
 	.get_nested_state_pages = svm_get_nested_state_pages,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/pmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/pmu.c
@@ -44,6 +44,22 @@
 	[7] = { 0xd1, 0x00, PERF_COUNT_HW_STALLED_CYCLES_BACKEND },
 };
 
+/* duplicated from amd_f17h_perfmon_event_map. */
+static struct kvm_event_hw_type_mapping amd_f17h_event_mapping[] = {
+	[0] = { 0x76, 0x00, PERF_COUNT_HW_CPU_CYCLES },
+	[1] = { 0xc0, 0x00, PERF_COUNT_HW_INSTRUCTIONS },
+	[2] = { 0x60, 0xff, PERF_COUNT_HW_CACHE_REFERENCES },
+	[3] = { 0x64, 0x09, PERF_COUNT_HW_CACHE_MISSES },
+	[4] = { 0xc2, 0x00, PERF_COUNT_HW_BRANCH_INSTRUCTIONS },
+	[5] = { 0xc3, 0x00, PERF_COUNT_HW_BRANCH_MISSES },
+	[6] = { 0x87, 0x02, PERF_COUNT_HW_STALLED_CYCLES_FRONTEND },
+	[7] = { 0x87, 0x01, PERF_COUNT_HW_STALLED_CYCLES_BACKEND },
+};
+
+/* amd_pmc_perf_hw_id depends on these being the same size */
+static_assert(ARRAY_SIZE(amd_event_mapping) ==
+	     ARRAY_SIZE(amd_f17h_event_mapping));
+
 static unsigned int get_msr_base(struct kvm_pmu *pmu, enum pmu_type type)
 {
 	struct kvm_vcpu *vcpu = pmu_to_vcpu(pmu);
@@ -134,21 +150,27 @@
 	return &pmu->gp_counters[msr_to_index(msr)];
 }
 
-static unsigned amd_find_arch_event(struct kvm_pmu *pmu,
-				    u8 event_select,
-				    u8 unit_mask)
+static unsigned int amd_pmc_perf_hw_id(struct kvm_pmc *pmc)
 {
+	struct kvm_event_hw_type_mapping *event_mapping;
+	u8 event_select = pmc->eventsel & ARCH_PERFMON_EVENTSEL_EVENT;
+	u8 unit_mask = (pmc->eventsel & ARCH_PERFMON_EVENTSEL_UMASK) >> 8;
 	int i;
 
+	if (guest_cpuid_family(pmc->vcpu) >= 0x17)
+		event_mapping = amd_f17h_event_mapping;
+	else
+		event_mapping = amd_event_mapping;
+
 	for (i = 0; i < ARRAY_SIZE(amd_event_mapping); i++)
-		if (amd_event_mapping[i].eventsel == event_select
-		    && amd_event_mapping[i].unit_mask == unit_mask)
+		if (event_mapping[i].eventsel == event_select
+		    && event_mapping[i].unit_mask == unit_mask)
 			break;
 
 	if (i == ARRAY_SIZE(amd_event_mapping))
 		return PERF_COUNT_HW_MAX;
 
-	return amd_event_mapping[i].event_type;
+	return event_mapping[i].event_type;
 }
 
 /* return PERF_COUNT_HW_MAX as AMD doesn't have fixed events */
@@ -256,17 +278,16 @@
 	pmc = get_gp_pmc_amd(pmu, msr, PMU_TYPE_COUNTER);
 	if (pmc) {
 		pmc->counter += data - pmc_read_counter(pmc);
+		pmc_update_sample_period(pmc);
 		return 0;
 	}
 	/* MSR_EVNTSELn */
 	pmc = get_gp_pmc_amd(pmu, msr, PMU_TYPE_EVNTSEL);
 	if (pmc) {
-		if (data == pmc->eventsel)
-			return 0;
-		if (!(data & pmu->reserved_bits)) {
+		data &= ~pmu->reserved_bits;
+		if (data != pmc->eventsel)
 			reprogram_gp_counter(pmc, data);
-			return 0;
-		}
+		return 0;
 	}
 
 	return 1;
@@ -282,7 +303,8 @@
 		pmu->nr_arch_gp_counters = AMD64_NUM_COUNTERS;
 
 	pmu->counter_bitmask[KVM_PMC_GP] = ((u64)1 << 48) - 1;
-	pmu->reserved_bits = 0xffffffff00200000ull;
+	pmu->reserved_bits = 0xfffffff000280000ull;
+	pmu->raw_event_mask = AMD64_RAW_EVENT_MASK;
 	pmu->version = 1;
 	/* not applicable to AMD; but clean them to prevent any fall out */
 	pmu->counter_bitmask[KVM_PMC_FIXED] = 0;
@@ -320,7 +342,7 @@
 }
 
 struct kvm_pmu_ops amd_pmu_ops = {
-	.find_arch_event = amd_find_arch_event,
+	.pmc_perf_hw_id = amd_pmc_perf_hw_id,
 	.find_fixed_event = amd_find_fixed_event,
 	.pmc_is_enabled = amd_pmc_is_enabled,
 	.pmc_idx_to_pmc = amd_pmc_idx_to_pmc,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/sev.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/sev.c
@@ -17,10 +17,10 @@
 #include <linux/misc_cgroup.h>
 #include <linux/processor.h>
 #include <linux/trace_events.h>
-#include <asm/fpu/internal.h>
 
 #include <asm/pkru.h>
 #include <asm/trapnr.h>
+#include <asm/fpu/xcr.h>
 
 #include "x86.h"
 #include "svm.h"
@@ -590,7 +590,7 @@
 	 * traditional VMSA as it has been built so far (in prep
 	 * for LAUNCH_UPDATE_VMSA) to be the initial SEV-ES state.
 	 */
-	memcpy(svm->vmsa, save, sizeof(*save));
+	memcpy(svm->sev_es.vmsa, save, sizeof(*save));
 
 	return 0;
 }
@@ -612,11 +612,11 @@
 	 * the VMSA memory content (i.e it will write the same memory region
 	 * with the guest's key), so invalidate it first.
 	 */
-	clflush_cache_range(svm->vmsa, PAGE_SIZE);
+	clflush_cache_range(svm->sev_es.vmsa, PAGE_SIZE);
 
 	vmsa.reserved = 0;
 	vmsa.handle = to_kvm_svm(kvm)->sev_info.handle;
-	vmsa.address = __sme_pa(svm->vmsa);
+	vmsa.address = __sme_pa(svm->sev_es.vmsa);
 	vmsa.len = PAGE_SIZE;
 	ret = sev_issue_cmd(kvm, SEV_CMD_LAUNCH_UPDATE_VMSA, &vmsa, error);
 	if (ret)
@@ -676,7 +676,7 @@
 		if (params.len > SEV_FW_BLOB_MAX_SIZE)
 			return -EINVAL;
 
-		blob = kmalloc(params.len, GFP_KERNEL_ACCOUNT);
+		blob = kzalloc(params.len, GFP_KERNEL_ACCOUNT);
 		if (!blob)
 			return -ENOMEM;
 
@@ -796,7 +796,7 @@
 	if (!IS_ALIGNED(dst_paddr, 16) ||
 	    !IS_ALIGNED(paddr,     16) ||
 	    !IS_ALIGNED(size,      16)) {
-		tpage = (void *)alloc_page(GFP_KERNEL);
+		tpage = (void *)alloc_page(GFP_KERNEL | __GFP_ZERO);
 		if (!tpage)
 			return -ENOMEM;
 
@@ -832,7 +832,7 @@
 
 	/* If source buffer is not aligned then use an intermediate buffer */
 	if (!IS_ALIGNED((unsigned long)vaddr, 16)) {
-		src_tpage = alloc_page(GFP_KERNEL);
+		src_tpage = alloc_page(GFP_KERNEL_ACCOUNT);
 		if (!src_tpage)
 			return -ENOMEM;
 
@@ -853,7 +853,7 @@
 	if (!IS_ALIGNED((unsigned long)dst_vaddr, 16) || !IS_ALIGNED(size, 16)) {
 		int dst_offset;
 
-		dst_tpage = alloc_page(GFP_KERNEL);
+		dst_tpage = alloc_page(GFP_KERNEL_ACCOUNT);
 		if (!dst_tpage) {
 			ret = -ENOMEM;
 			goto e_free;
@@ -1082,7 +1082,7 @@
 		if (params.len > SEV_FW_BLOB_MAX_SIZE)
 			return -EINVAL;
 
-		blob = kmalloc(params.len, GFP_KERNEL_ACCOUNT);
+		blob = kzalloc(params.len, GFP_KERNEL_ACCOUNT);
 		if (!blob)
 			return -ENOMEM;
 
@@ -1164,7 +1164,7 @@
 		return -EINVAL;
 
 	/* allocate the memory to hold the session data blob */
-	session_data = kmalloc(params.session_len, GFP_KERNEL_ACCOUNT);
+	session_data = kzalloc(params.session_len, GFP_KERNEL_ACCOUNT);
 	if (!session_data)
 		return -ENOMEM;
 
@@ -1277,7 +1277,7 @@
 
 	/* Check if we are crossing the page boundary */
 	offset = params.guest_uaddr & (PAGE_SIZE - 1);
-	if ((params.guest_len + offset > PAGE_SIZE))
+	if (params.guest_len > PAGE_SIZE || (params.guest_len + offset) > PAGE_SIZE)
 		return -EINVAL;
 
 	/* Pin guest memory */
@@ -1288,11 +1288,11 @@
 
 	/* allocate memory for header and transport buffer */
 	ret = -ENOMEM;
-	hdr = kmalloc(params.hdr_len, GFP_KERNEL_ACCOUNT);
+	hdr = kzalloc(params.hdr_len, GFP_KERNEL_ACCOUNT);
 	if (!hdr)
 		goto e_unpin;
 
-	trans_data = kmalloc(params.trans_len, GFP_KERNEL_ACCOUNT);
+	trans_data = kzalloc(params.trans_len, GFP_KERNEL_ACCOUNT);
 	if (!trans_data)
 		goto e_free_hdr;
 
@@ -1457,7 +1457,7 @@
 
 	/* Check if we are crossing the page boundary */
 	offset = params.guest_uaddr & (PAGE_SIZE - 1);
-	if ((params.guest_len + offset > PAGE_SIZE))
+	if (params.guest_len > PAGE_SIZE || (params.guest_len + offset) > PAGE_SIZE)
 		return -EINVAL;
 
 	hdr = psp_copy_user_blob(params.hdr_uaddr, params.hdr_len);
@@ -1662,20 +1662,22 @@
 		goto e_free;
 	}
 
-	region->uaddr = range->addr;
-	region->size = range->size;
-
-	list_add_tail(&region->list, &sev->regions_list);
-	mutex_unlock(&kvm->lock);
-
 	/*
 	 * The guest may change the memory encryption attribute from C=0 -> C=1
 	 * or vice versa for this memory range. Lets make sure caches are
 	 * flushed to ensure that guest data gets written into memory with
-	 * correct C-bit.
+	 * correct C-bit.  Note, this must be done before dropping kvm->lock,
+	 * as region and its array of pages can be freed by a different task
+	 * once kvm->lock is released.
 	 */
 	sev_clflush_pages(region->pages, region->npages);
 
+	region->uaddr = range->addr;
+	region->size = range->size;
+
+	list_add_tail(&region->list, &sev->regions_list);
+	mutex_unlock(&kvm->lock);
+
 	return ret;
 
 e_free:
@@ -1787,7 +1789,12 @@
 	mutex_unlock(&source_kvm->lock);
 	mutex_lock(&kvm->lock);
 
-	if (sev_guest(kvm)) {
+	/*
+	 * Disallow out-of-band SEV/SEV-ES init if the target is already an
+	 * SEV guest, or if vCPUs have been created.  KVM relies on vCPUs being
+	 * created after SEV/SEV-ES initialization, e.g. to init intercepts.
+	 */
+	if (sev_guest(kvm) || kvm->created_vcpus) {
 		ret = -EINVAL;
 		goto e_mirror_unlock;
 	}
@@ -1800,6 +1807,7 @@
 	mirror_sev->fd = source_sev.fd;
 	mirror_sev->es_active = source_sev.es_active;
 	mirror_sev->handle = source_sev.handle;
+	INIT_LIST_HEAD(&mirror_sev->regions_list);
 	/*
 	 * Do not copy ap_jump_table. Since the mirror does not share the same
 	 * KVM contexts as the original, and they may have different
@@ -1984,11 +1992,14 @@
 				   unsigned long len)
 {
 	/*
-	 * If hardware enforced cache coherency for encrypted mappings of the
-	 * same physical page is supported, nothing to do.
+	 * If CPU enforced cache coherency for encrypted mappings of the
+	 * same physical page is supported, use CLFLUSHOPT instead. NOTE: cache
+	 * flush is still needed in order to work properly with DMA devices.
 	 */
-	if (boot_cpu_has(X86_FEATURE_SME_COHERENT))
+	if (boot_cpu_has(X86_FEATURE_SME_COHERENT)) {
+		clflush_cache_range(va, PAGE_SIZE);
 		return;
+	}
 
 	/*
 	 * If the VM Page Flush MSR is supported, use it to flush the page
@@ -2028,6 +2039,14 @@
 	wbinvd_on_all_cpus();
 }
 
+void sev_guest_memory_reclaimed(struct kvm *kvm)
+{
+	if (!sev_guest(kvm))
+		return;
+
+	wbinvd_on_all_cpus();
+}
+
 void sev_free_vcpu(struct kvm_vcpu *vcpu)
 {
 	struct vcpu_svm *svm;
@@ -2038,16 +2057,16 @@
 	svm = to_svm(vcpu);
 
 	if (vcpu->arch.guest_state_protected)
-		sev_flush_guest_memory(svm, svm->vmsa, PAGE_SIZE);
-	__free_page(virt_to_page(svm->vmsa));
+		sev_flush_guest_memory(svm, svm->sev_es.vmsa, PAGE_SIZE);
+	__free_page(virt_to_page(svm->sev_es.vmsa));
 
-	if (svm->ghcb_sa_free)
-		kfree(svm->ghcb_sa);
+	if (svm->sev_es.ghcb_sa_free)
+		kvfree(svm->sev_es.ghcb_sa);
 }
 
 static void dump_ghcb(struct vcpu_svm *svm)
 {
-	struct ghcb *ghcb = svm->ghcb;
+	struct ghcb *ghcb = svm->sev_es.ghcb;
 	unsigned int nbits;
 
 	/* Re-use the dump_invalid_vmcb module parameter */
@@ -2073,7 +2092,7 @@
 static void sev_es_sync_to_ghcb(struct vcpu_svm *svm)
 {
 	struct kvm_vcpu *vcpu = &svm->vcpu;
-	struct ghcb *ghcb = svm->ghcb;
+	struct ghcb *ghcb = svm->sev_es.ghcb;
 
 	/*
 	 * The GHCB protocol so far allows for the following data
@@ -2093,7 +2112,7 @@
 {
 	struct vmcb_control_area *control = &svm->vmcb->control;
 	struct kvm_vcpu *vcpu = &svm->vcpu;
-	struct ghcb *ghcb = svm->ghcb;
+	struct ghcb *ghcb = svm->sev_es.ghcb;
 	u64 exit_code;
 
 	/*
@@ -2110,15 +2129,18 @@
 	 */
 	memset(vcpu->arch.regs, 0, sizeof(vcpu->arch.regs));
 
-	vcpu->arch.regs[VCPU_REGS_RAX] = ghcb_get_rax_if_valid(ghcb);
-	vcpu->arch.regs[VCPU_REGS_RBX] = ghcb_get_rbx_if_valid(ghcb);
-	vcpu->arch.regs[VCPU_REGS_RCX] = ghcb_get_rcx_if_valid(ghcb);
-	vcpu->arch.regs[VCPU_REGS_RDX] = ghcb_get_rdx_if_valid(ghcb);
-	vcpu->arch.regs[VCPU_REGS_RSI] = ghcb_get_rsi_if_valid(ghcb);
+	BUILD_BUG_ON(sizeof(svm->sev_es.valid_bitmap) != sizeof(ghcb->save.valid_bitmap));
+	memcpy(&svm->sev_es.valid_bitmap, &ghcb->save.valid_bitmap, sizeof(ghcb->save.valid_bitmap));
+
+	vcpu->arch.regs[VCPU_REGS_RAX] = kvm_ghcb_get_rax_if_valid(svm, ghcb);
+	vcpu->arch.regs[VCPU_REGS_RBX] = kvm_ghcb_get_rbx_if_valid(svm, ghcb);
+	vcpu->arch.regs[VCPU_REGS_RCX] = kvm_ghcb_get_rcx_if_valid(svm, ghcb);
+	vcpu->arch.regs[VCPU_REGS_RDX] = kvm_ghcb_get_rdx_if_valid(svm, ghcb);
+	vcpu->arch.regs[VCPU_REGS_RSI] = kvm_ghcb_get_rsi_if_valid(svm, ghcb);
 
-	svm->vmcb->save.cpl = ghcb_get_cpl_if_valid(ghcb);
+	svm->vmcb->save.cpl = kvm_ghcb_get_cpl_if_valid(svm, ghcb);
 
-	if (ghcb_xcr0_is_valid(ghcb)) {
+	if (kvm_ghcb_xcr0_is_valid(svm)) {
 		vcpu->arch.xcr0 = ghcb_get_xcr0(ghcb);
 		kvm_update_cpuid_runtime(vcpu);
 	}
@@ -2129,79 +2151,91 @@
 	control->exit_code_hi = upper_32_bits(exit_code);
 	control->exit_info_1 = ghcb_get_sw_exit_info_1(ghcb);
 	control->exit_info_2 = ghcb_get_sw_exit_info_2(ghcb);
+	svm->sev_es.sw_scratch = kvm_ghcb_get_sw_scratch_if_valid(svm, ghcb);
 
 	/* Clear the valid entries fields */
 	memset(ghcb->save.valid_bitmap, 0, sizeof(ghcb->save.valid_bitmap));
 }
 
+static u64 kvm_ghcb_get_sw_exit_code(struct vmcb_control_area *control)
+{
+	return (((u64)control->exit_code_hi) << 32) | control->exit_code;
+}
+
 static int sev_es_validate_vmgexit(struct vcpu_svm *svm)
 {
-	struct kvm_vcpu *vcpu;
+	struct vmcb_control_area *control = &svm->vmcb->control;
+	struct kvm_vcpu *vcpu = &svm->vcpu;
 	struct ghcb *ghcb;
-	u64 exit_code = 0;
+	u64 exit_code;
+	u64 reason;
 
-	ghcb = svm->ghcb;
-
-	/* Only GHCB Usage code 0 is supported */
-	if (ghcb->ghcb_usage)
-		goto vmgexit_err;
+	ghcb = svm->sev_es.ghcb;
 
 	/*
-	 * Retrieve the exit code now even though is may not be marked valid
+	 * Retrieve the exit code now even though it may not be marked valid
 	 * as it could help with debugging.
 	 */
-	exit_code = ghcb_get_sw_exit_code(ghcb);
+	exit_code = kvm_ghcb_get_sw_exit_code(control);
 
-	if (!ghcb_sw_exit_code_is_valid(ghcb) ||
-	    !ghcb_sw_exit_info_1_is_valid(ghcb) ||
-	    !ghcb_sw_exit_info_2_is_valid(ghcb))
+	/* Only GHCB Usage code 0 is supported */
+	if (ghcb->ghcb_usage) {
+		reason = GHCB_ERR_INVALID_USAGE;
 		goto vmgexit_err;
+	}
+
+	reason = GHCB_ERR_MISSING_INPUT;
 
-	switch (ghcb_get_sw_exit_code(ghcb)) {
+	if (!kvm_ghcb_sw_exit_code_is_valid(svm) ||
+	    !kvm_ghcb_sw_exit_info_1_is_valid(svm) ||
+	    !kvm_ghcb_sw_exit_info_2_is_valid(svm))
+		goto vmgexit_err;
+
+	switch (exit_code) {
 	case SVM_EXIT_READ_DR7:
 		break;
 	case SVM_EXIT_WRITE_DR7:
-		if (!ghcb_rax_is_valid(ghcb))
+		if (!kvm_ghcb_rax_is_valid(svm))
 			goto vmgexit_err;
 		break;
 	case SVM_EXIT_RDTSC:
 		break;
 	case SVM_EXIT_RDPMC:
-		if (!ghcb_rcx_is_valid(ghcb))
+		if (!kvm_ghcb_rcx_is_valid(svm))
 			goto vmgexit_err;
 		break;
 	case SVM_EXIT_CPUID:
-		if (!ghcb_rax_is_valid(ghcb) ||
-		    !ghcb_rcx_is_valid(ghcb))
+		if (!kvm_ghcb_rax_is_valid(svm) ||
+		    !kvm_ghcb_rcx_is_valid(svm))
 			goto vmgexit_err;
-		if (ghcb_get_rax(ghcb) == 0xd)
-			if (!ghcb_xcr0_is_valid(ghcb))
+		if (vcpu->arch.regs[VCPU_REGS_RAX] == 0xd)
+			if (!kvm_ghcb_xcr0_is_valid(svm))
 				goto vmgexit_err;
 		break;
 	case SVM_EXIT_INVD:
 		break;
 	case SVM_EXIT_IOIO:
-		if (ghcb_get_sw_exit_info_1(ghcb) & SVM_IOIO_STR_MASK) {
-			if (!ghcb_sw_scratch_is_valid(ghcb))
+		if (control->exit_info_1 & SVM_IOIO_STR_MASK) {
+			if (!kvm_ghcb_sw_scratch_is_valid(svm))
 				goto vmgexit_err;
 		} else {
-			if (!(ghcb_get_sw_exit_info_1(ghcb) & SVM_IOIO_TYPE_MASK))
-				if (!ghcb_rax_is_valid(ghcb))
+			if (!(control->exit_info_1 & SVM_IOIO_TYPE_MASK))
+				if (!kvm_ghcb_rax_is_valid(svm))
 					goto vmgexit_err;
 		}
 		break;
 	case SVM_EXIT_MSR:
-		if (!ghcb_rcx_is_valid(ghcb))
+		if (!kvm_ghcb_rcx_is_valid(svm))
 			goto vmgexit_err;
-		if (ghcb_get_sw_exit_info_1(ghcb)) {
-			if (!ghcb_rax_is_valid(ghcb) ||
-			    !ghcb_rdx_is_valid(ghcb))
+		if (control->exit_info_1) {
+			if (!kvm_ghcb_rax_is_valid(svm) ||
+			    !kvm_ghcb_rdx_is_valid(svm))
 				goto vmgexit_err;
 		}
 		break;
 	case SVM_EXIT_VMMCALL:
-		if (!ghcb_rax_is_valid(ghcb) ||
-		    !ghcb_cpl_is_valid(ghcb))
+		if (!kvm_ghcb_rax_is_valid(svm) ||
+		    !kvm_ghcb_cpl_is_valid(svm))
 			goto vmgexit_err;
 		break;
 	case SVM_EXIT_RDTSCP:
@@ -2209,19 +2243,19 @@
 	case SVM_EXIT_WBINVD:
 		break;
 	case SVM_EXIT_MONITOR:
-		if (!ghcb_rax_is_valid(ghcb) ||
-		    !ghcb_rcx_is_valid(ghcb) ||
-		    !ghcb_rdx_is_valid(ghcb))
+		if (!kvm_ghcb_rax_is_valid(svm) ||
+		    !kvm_ghcb_rcx_is_valid(svm) ||
+		    !kvm_ghcb_rdx_is_valid(svm))
 			goto vmgexit_err;
 		break;
 	case SVM_EXIT_MWAIT:
-		if (!ghcb_rax_is_valid(ghcb) ||
-		    !ghcb_rcx_is_valid(ghcb))
+		if (!kvm_ghcb_rax_is_valid(svm) ||
+		    !kvm_ghcb_rcx_is_valid(svm))
 			goto vmgexit_err;
 		break;
 	case SVM_VMGEXIT_MMIO_READ:
 	case SVM_VMGEXIT_MMIO_WRITE:
-		if (!ghcb_sw_scratch_is_valid(ghcb))
+		if (!kvm_ghcb_sw_scratch_is_valid(svm))
 			goto vmgexit_err;
 		break;
 	case SVM_VMGEXIT_NMI_COMPLETE:
@@ -2230,61 +2264,62 @@
 	case SVM_VMGEXIT_UNSUPPORTED_EVENT:
 		break;
 	default:
+		reason = GHCB_ERR_INVALID_EVENT;
 		goto vmgexit_err;
 	}
 
 	return 0;
 
 vmgexit_err:
-	vcpu = &svm->vcpu;
-
-	if (ghcb->ghcb_usage) {
+	if (reason == GHCB_ERR_INVALID_USAGE) {
 		vcpu_unimpl(vcpu, "vmgexit: ghcb usage %#x is not valid\n",
 			    ghcb->ghcb_usage);
+	} else if (reason == GHCB_ERR_INVALID_EVENT) {
+		vcpu_unimpl(vcpu, "vmgexit: exit code %#llx is not valid\n",
+			    exit_code);
 	} else {
-		vcpu_unimpl(vcpu, "vmgexit: exit reason %#llx is not valid\n",
+		vcpu_unimpl(vcpu, "vmgexit: exit code %#llx input is not valid\n",
 			    exit_code);
 		dump_ghcb(svm);
 	}
 
-	vcpu->run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
-	vcpu->run->internal.suberror = KVM_INTERNAL_ERROR_UNEXPECTED_EXIT_REASON;
-	vcpu->run->internal.ndata = 2;
-	vcpu->run->internal.data[0] = exit_code;
-	vcpu->run->internal.data[1] = vcpu->arch.last_vmentry_cpu;
+	ghcb_set_sw_exit_info_1(ghcb, 2);
+	ghcb_set_sw_exit_info_2(ghcb, reason);
 
-	return -EINVAL;
+	/* Resume the guest to "return" the error code. */
+	return 1;
 }
 
 void sev_es_unmap_ghcb(struct vcpu_svm *svm)
 {
-	if (!svm->ghcb)
+	if (!svm->sev_es.ghcb)
 		return;
 
-	if (svm->ghcb_sa_free) {
+	if (svm->sev_es.ghcb_sa_free) {
 		/*
 		 * The scratch area lives outside the GHCB, so there is a
 		 * buffer that, depending on the operation performed, may
 		 * need to be synced, then freed.
 		 */
-		if (svm->ghcb_sa_sync) {
+		if (svm->sev_es.ghcb_sa_sync) {
 			kvm_write_guest(svm->vcpu.kvm,
-					ghcb_get_sw_scratch(svm->ghcb),
-					svm->ghcb_sa, svm->ghcb_sa_len);
-			svm->ghcb_sa_sync = false;
+					svm->sev_es.sw_scratch,
+					svm->sev_es.ghcb_sa,
+					svm->sev_es.ghcb_sa_len);
+			svm->sev_es.ghcb_sa_sync = false;
 		}
 
-		kfree(svm->ghcb_sa);
-		svm->ghcb_sa = NULL;
-		svm->ghcb_sa_free = false;
+		kvfree(svm->sev_es.ghcb_sa);
+		svm->sev_es.ghcb_sa = NULL;
+		svm->sev_es.ghcb_sa_free = false;
 	}
 
-	trace_kvm_vmgexit_exit(svm->vcpu.vcpu_id, svm->ghcb);
+	trace_kvm_vmgexit_exit(svm->vcpu.vcpu_id, svm->sev_es.ghcb);
 
 	sev_es_sync_to_ghcb(svm);
 
-	kvm_vcpu_unmap(&svm->vcpu, &svm->ghcb_map, true);
-	svm->ghcb = NULL;
+	kvm_vcpu_unmap(&svm->vcpu, &svm->sev_es.ghcb_map, true);
+	svm->sev_es.ghcb = NULL;
 }
 
 void pre_sev_run(struct vcpu_svm *svm, int cpu)
@@ -2311,25 +2346,25 @@
 }
 
 #define GHCB_SCRATCH_AREA_LIMIT		(16ULL * PAGE_SIZE)
-static bool setup_vmgexit_scratch(struct vcpu_svm *svm, bool sync, u64 len)
+static int setup_vmgexit_scratch(struct vcpu_svm *svm, bool sync, u64 len)
 {
 	struct vmcb_control_area *control = &svm->vmcb->control;
-	struct ghcb *ghcb = svm->ghcb;
+	struct ghcb *ghcb = svm->sev_es.ghcb;
 	u64 ghcb_scratch_beg, ghcb_scratch_end;
 	u64 scratch_gpa_beg, scratch_gpa_end;
 	void *scratch_va;
 
-	scratch_gpa_beg = ghcb_get_sw_scratch(ghcb);
+	scratch_gpa_beg = svm->sev_es.sw_scratch;
 	if (!scratch_gpa_beg) {
 		pr_err("vmgexit: scratch gpa not provided\n");
-		return false;
+		goto e_scratch;
 	}
 
 	scratch_gpa_end = scratch_gpa_beg + len;
 	if (scratch_gpa_end < scratch_gpa_beg) {
 		pr_err("vmgexit: scratch length (%#llx) not valid for scratch address (%#llx)\n",
 		       len, scratch_gpa_beg);
-		return false;
+		goto e_scratch;
 	}
 
 	if ((scratch_gpa_beg & PAGE_MASK) == control->ghcb_gpa) {
@@ -2347,10 +2382,10 @@
 		    scratch_gpa_end > ghcb_scratch_end) {
 			pr_err("vmgexit: scratch area is outside of GHCB shared buffer area (%#llx - %#llx)\n",
 			       scratch_gpa_beg, scratch_gpa_end);
-			return false;
+			goto e_scratch;
 		}
 
-		scratch_va = (void *)svm->ghcb;
+		scratch_va = (void *)svm->sev_es.ghcb;
 		scratch_va += (scratch_gpa_beg - control->ghcb_gpa);
 	} else {
 		/*
@@ -2360,18 +2395,18 @@
 		if (len > GHCB_SCRATCH_AREA_LIMIT) {
 			pr_err("vmgexit: scratch area exceeds KVM limits (%#llx requested, %#llx limit)\n",
 			       len, GHCB_SCRATCH_AREA_LIMIT);
-			return false;
+			goto e_scratch;
 		}
-		scratch_va = kzalloc(len, GFP_KERNEL_ACCOUNT);
+		scratch_va = kvzalloc(len, GFP_KERNEL_ACCOUNT);
 		if (!scratch_va)
-			return false;
+			return -ENOMEM;
 
 		if (kvm_read_guest(svm->vcpu.kvm, scratch_gpa_beg, scratch_va, len)) {
 			/* Unable to copy scratch area from guest */
 			pr_err("vmgexit: kvm_read_guest for scratch area failed\n");
 
-			kfree(scratch_va);
-			return false;
+			kvfree(scratch_va);
+			return -EFAULT;
 		}
 
 		/*
@@ -2380,14 +2415,20 @@
 		 * the vCPU next time (i.e. a read was requested so the data
 		 * must be written back to the guest memory).
 		 */
-		svm->ghcb_sa_sync = sync;
-		svm->ghcb_sa_free = true;
+		svm->sev_es.ghcb_sa_sync = sync;
+		svm->sev_es.ghcb_sa_free = true;
 	}
 
-	svm->ghcb_sa = scratch_va;
-	svm->ghcb_sa_len = len;
+	svm->sev_es.ghcb_sa = scratch_va;
+	svm->sev_es.ghcb_sa_len = len;
 
-	return true;
+	return 0;
+
+e_scratch:
+	ghcb_set_sw_exit_info_1(ghcb, 2);
+	ghcb_set_sw_exit_info_2(ghcb, GHCB_ERR_INVALID_SCRATCH_AREA);
+
+	return 1;
 }
 
 static void set_ghcb_msr_bits(struct vcpu_svm *svm, u64 value, u64 mask,
@@ -2438,7 +2479,7 @@
 
 		ret = svm_invoke_exit_handler(vcpu, SVM_EXIT_CPUID);
 		if (!ret) {
-			ret = -EINVAL;
+			/* Error, keep GHCB MSR value as-is */
 			break;
 		}
 
@@ -2474,10 +2515,13 @@
 						GHCB_MSR_TERM_REASON_POS);
 		pr_info("SEV-ES guest requested termination: %#llx:%#llx\n",
 			reason_set, reason_code);
-		fallthrough;
+
+		ret = -EINVAL;
+		break;
 	}
 	default:
-		ret = -EINVAL;
+		/* Error, keep GHCB MSR value as-is */
+		break;
 	}
 
 	trace_kvm_vmgexit_msr_protocol_exit(svm->vcpu.vcpu_id,
@@ -2501,50 +2545,54 @@
 
 	if (!ghcb_gpa) {
 		vcpu_unimpl(vcpu, "vmgexit: GHCB gpa is not set\n");
-		return -EINVAL;
+
+		/* Without a GHCB, just return right back to the guest */
+		return 1;
 	}
 
-	if (kvm_vcpu_map(vcpu, ghcb_gpa >> PAGE_SHIFT, &svm->ghcb_map)) {
+	if (kvm_vcpu_map(vcpu, ghcb_gpa >> PAGE_SHIFT, &svm->sev_es.ghcb_map)) {
 		/* Unable to map GHCB from guest */
 		vcpu_unimpl(vcpu, "vmgexit: error mapping GHCB [%#llx] from guest\n",
 			    ghcb_gpa);
-		return -EINVAL;
+
+		/* Without a GHCB, just return right back to the guest */
+		return 1;
 	}
 
-	svm->ghcb = svm->ghcb_map.hva;
-	ghcb = svm->ghcb_map.hva;
+	svm->sev_es.ghcb = svm->sev_es.ghcb_map.hva;
+	ghcb = svm->sev_es.ghcb_map.hva;
 
 	trace_kvm_vmgexit_enter(vcpu->vcpu_id, ghcb);
 
-	exit_code = ghcb_get_sw_exit_code(ghcb);
-
+	sev_es_sync_from_ghcb(svm);
 	ret = sev_es_validate_vmgexit(svm);
 	if (ret)
 		return ret;
 
-	sev_es_sync_from_ghcb(svm);
 	ghcb_set_sw_exit_info_1(ghcb, 0);
 	ghcb_set_sw_exit_info_2(ghcb, 0);
 
-	ret = -EINVAL;
+	exit_code = kvm_ghcb_get_sw_exit_code(control);
 	switch (exit_code) {
 	case SVM_VMGEXIT_MMIO_READ:
-		if (!setup_vmgexit_scratch(svm, true, control->exit_info_2))
+		ret = setup_vmgexit_scratch(svm, true, control->exit_info_2);
+		if (ret)
 			break;
 
 		ret = kvm_sev_es_mmio_read(vcpu,
 					   control->exit_info_1,
 					   control->exit_info_2,
-					   svm->ghcb_sa);
+					   svm->sev_es.ghcb_sa);
 		break;
 	case SVM_VMGEXIT_MMIO_WRITE:
-		if (!setup_vmgexit_scratch(svm, false, control->exit_info_2))
+		ret = setup_vmgexit_scratch(svm, false, control->exit_info_2);
+		if (ret)
 			break;
 
 		ret = kvm_sev_es_mmio_write(vcpu,
 					    control->exit_info_1,
 					    control->exit_info_2,
-					    svm->ghcb_sa);
+					    svm->sev_es.ghcb_sa);
 		break;
 	case SVM_VMGEXIT_NMI_COMPLETE:
 		ret = svm_invoke_exit_handler(vcpu, SVM_EXIT_IRET);
@@ -2567,11 +2615,8 @@
 		default:
 			pr_err("svm: vmgexit: unsupported AP jump table request - exit_info_1=%#llx\n",
 			       control->exit_info_1);
-			ghcb_set_sw_exit_info_1(ghcb, 1);
-			ghcb_set_sw_exit_info_2(ghcb,
-						X86_TRAP_UD |
-						SVM_EVTINJ_TYPE_EXEPT |
-						SVM_EVTINJ_VALID);
+			ghcb_set_sw_exit_info_1(ghcb, 2);
+			ghcb_set_sw_exit_info_2(ghcb, GHCB_ERR_INVALID_INPUT);
 		}
 
 		ret = 1;
@@ -2581,6 +2626,7 @@
 		vcpu_unimpl(vcpu,
 			    "vmgexit: unsupported event - exit_info_1=%#llx, exit_info_2=%#llx\n",
 			    control->exit_info_1, control->exit_info_2);
+		ret = -EINVAL;
 		break;
 	default:
 		ret = svm_invoke_exit_handler(vcpu, exit_code);
@@ -2593,6 +2639,7 @@
 {
 	int count;
 	int bytes;
+	int r;
 
 	if (svm->vmcb->control.exit_info_2 > INT_MAX)
 		return -EINVAL;
@@ -2601,10 +2648,12 @@
 	if (unlikely(check_mul_overflow(count, size, &bytes)))
 		return -EINVAL;
 
-	if (!setup_vmgexit_scratch(svm, in, bytes))
-		return -EINVAL;
+	r = setup_vmgexit_scratch(svm, in, bytes);
+	if (r)
+		return r;
 
-	return kvm_sev_es_string_io(&svm->vcpu, size, port, svm->ghcb_sa, count, in);
+	return kvm_sev_es_string_io(&svm->vcpu, size, port, svm->sev_es.ghcb_sa,
+				    count, in);
 }
 
 void sev_es_init_vmcb(struct vcpu_svm *svm)
@@ -2619,7 +2668,7 @@
 	 * VMCB page. Do not include the encryption mask on the VMSA physical
 	 * address since hardware will access it using the guest key.
 	 */
-	svm->vmcb->control.vmsa_pa = __pa(svm->vmsa);
+	svm->vmcb->control.vmsa_pa = __pa(svm->sev_es.vmsa);
 
 	/* Can't intercept CR register access, HV can't modify CR registers */
 	svm_clr_intercept(svm, INTERCEPT_CR0_READ);
@@ -2691,8 +2740,8 @@
 	struct vcpu_svm *svm = to_svm(vcpu);
 
 	/* First SIPI: Use the values as initially set by the VMM */
-	if (!svm->received_first_sipi) {
-		svm->received_first_sipi = true;
+	if (!svm->sev_es.received_first_sipi) {
+		svm->sev_es.received_first_sipi = true;
 		return;
 	}
 
@@ -2701,8 +2750,8 @@
 	 * the guest will set the CS and RIP. Set SW_EXIT_INFO_2 to a
 	 * non-zero value.
 	 */
-	if (!svm->ghcb)
+	if (!svm->sev_es.ghcb)
 		return;
 
-	ghcb_set_sw_exit_info_2(svm->ghcb, 1);
+	ghcb_set_sw_exit_info_2(svm->sev_es.ghcb, 1);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/svm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/svm.c
@@ -36,6 +36,7 @@
 #include <asm/spec-ctrl.h>
 #include <asm/cpu_device_id.h>
 #include <asm/traps.h>
+#include <asm/fpu/api.h>
 
 #include <asm/virtext.h>
 #include "trace.h"
@@ -281,7 +282,7 @@
 
 	if ((old_efer & EFER_SVME) != (efer & EFER_SVME)) {
 		if (!(efer & EFER_SVME)) {
-			svm_leave_nested(svm);
+			svm_leave_nested(vcpu);
 			svm_set_gif(svm, true);
 			/* #GP intercept is still needed for vmware backdoor */
 			if (!enable_vmware_backdoor)
@@ -303,7 +304,11 @@
 				return ret;
 			}
 
-			if (svm_gp_erratum_intercept)
+			/*
+			 * Never intercept #GP for SEV guests, KVM can't
+			 * decrypt guest memory to workaround the erratum.
+			 */
+			if (svm_gp_erratum_intercept && !sev_guest(vcpu->kvm))
 				set_exception_intercept(svm, GP_VECTOR);
 		}
 	}
@@ -313,12 +318,6 @@
 	return 0;
 }
 
-static int is_external_interrupt(u32 info)
-{
-	info &= SVM_EVTINJ_TYPE_MASK | SVM_EVTINJ_VALID;
-	return info == (SVM_EVTINJ_VALID | SVM_EVTINJ_TYPE_INTR);
-}
-
 static u32 svm_get_interrupt_shadow(struct kvm_vcpu *vcpu)
 {
 	struct vcpu_svm *svm = to_svm(vcpu);
@@ -390,6 +389,10 @@
 		 */
 		(void)skip_emulated_instruction(vcpu);
 		rip = kvm_rip_read(vcpu);
+
+		if (boot_cpu_has(X86_FEATURE_NRIPS))
+			svm->vmcb->control.next_rip = rip;
+
 		svm->int3_rip = rip + svm->vmcb->save.cs.base;
 		svm->int3_injected = rip - old_rip;
 	}
@@ -463,11 +466,24 @@
 	return 1;
 }
 
+void __svm_write_tsc_multiplier(u64 multiplier)
+{
+	preempt_disable();
+
+	if (multiplier == __this_cpu_read(current_tsc_ratio))
+		goto out;
+
+	wrmsrl(MSR_AMD64_TSC_RATIO, multiplier);
+	__this_cpu_write(current_tsc_ratio, multiplier);
+out:
+	preempt_enable();
+}
+
 static void svm_hardware_disable(void)
 {
 	/* Make sure we clean up behind us */
 	if (static_cpu_has(X86_FEATURE_TSCRATEMSR))
-		wrmsrl(MSR_AMD64_TSC_RATIO, TSC_RATIO_DEFAULT);
+		__svm_write_tsc_multiplier(TSC_RATIO_DEFAULT);
 
 	cpu_svm_disable();
 
@@ -509,8 +525,11 @@
 	wrmsrl(MSR_VM_HSAVE_PA, __sme_page_pa(sd->save_area));
 
 	if (static_cpu_has(X86_FEATURE_TSCRATEMSR)) {
-		wrmsrl(MSR_AMD64_TSC_RATIO, TSC_RATIO_DEFAULT);
-		__this_cpu_write(current_tsc_ratio, TSC_RATIO_DEFAULT);
+		/*
+		 * Set the default value, even if we don't use TSC scaling
+		 * to avoid having stale value in the msr
+		 */
+		__svm_write_tsc_multiplier(TSC_RATIO_DEFAULT);
 	}
 
 
@@ -940,6 +959,9 @@
 
 	/* CPUID 0x8000001F (SME/SEV features) */
 	sev_set_cpu_caps();
+
+	/* Don't advertise Bus Lock Detect to guest if SVM support is absent */
+	kvm_cpu_cap_clear(X86_FEATURE_BUS_LOCK_DETECT);
 }
 
 static __init int svm_hardware_setup(void)
@@ -1123,9 +1145,10 @@
 
 static void svm_write_tsc_multiplier(struct kvm_vcpu *vcpu, u64 multiplier)
 {
-	wrmsrl(MSR_AMD64_TSC_RATIO, multiplier);
+	__svm_write_tsc_multiplier(multiplier);
 }
 
+
 /* Evaluate instruction intercepts that depend on guest CPUID features. */
 static void svm_recalc_instruction_intercepts(struct kvm_vcpu *vcpu,
 					      struct vcpu_svm *svm)
@@ -1176,9 +1199,10 @@
 	 * Guest access to VMware backdoor ports could legitimately
 	 * trigger #GP because of TSS I/O permission bitmap.
 	 * We intercept those #GP and allow access to them anyway
-	 * as VMware does.
+	 * as VMware does.  Don't intercept #GP for SEV guests as KVM can't
+	 * decrypt guest memory to decode the faulting instruction.
 	 */
-	if (enable_vmware_backdoor)
+	if (enable_vmware_backdoor && !sev_guest(vcpu->kvm))
 		set_exception_intercept(svm, GP_VECTOR);
 
 	svm_set_intercept(svm, INTERCEPT_INTR);
@@ -1346,10 +1370,10 @@
 		/*
 		 * SEV-ES guests maintain an encrypted version of their FPU
 		 * state which is restored and saved on VMRUN and VMEXIT.
-		 * Free the fpu structure to prevent KVM from attempting to
-		 * access the FPU state.
+		 * Mark vcpu->arch.guest_fpu->fpstate as scratch so it won't
+		 * do xsave/xrstor on it.
 		 */
-		kvm_free_guest_fpu(vcpu);
+		fpstate_set_confidential(&vcpu->arch.guest_fpu);
 	}
 
 	err = avic_init_vcpu(svm);
@@ -1372,7 +1396,7 @@
 	svm->vmcb01.pa = __sme_set(page_to_pfn(vmcb01_page) << PAGE_SHIFT);
 
 	if (vmsa_page)
-		svm->vmsa = page_address(vmsa_page);
+		svm->sev_es.vmsa = page_address(vmsa_page);
 
 	svm->guest_state_loaded = false;
 
@@ -1418,6 +1442,7 @@
 	 */
 	svm_clear_current_vmcb(svm->vmcb);
 
+	svm_leave_nested(vcpu);
 	svm_free_nested(svm);
 
 	sev_free_vcpu(vcpu);
@@ -1447,13 +1472,8 @@
 		vmsave(__sme_page_pa(sd->save_area));
 	}
 
-	if (static_cpu_has(X86_FEATURE_TSCRATEMSR)) {
-		u64 tsc_ratio = vcpu->arch.tsc_scaling_ratio;
-		if (tsc_ratio != __this_cpu_read(current_tsc_ratio)) {
-			__this_cpu_write(current_tsc_ratio, tsc_ratio);
-			wrmsrl(MSR_AMD64_TSC_RATIO, tsc_ratio);
-		}
-	}
+	if (static_cpu_has(X86_FEATURE_TSCRATEMSR))
+		__svm_write_tsc_multiplier(vcpu->arch.tsc_scaling_ratio);
 
 	if (likely(tsc_aux_uret_slot >= 0))
 		kvm_set_user_return_msr(tsc_aux_uret_slot, svm->tsc_aux, -1ull);
@@ -1473,7 +1493,9 @@
 
 	if (sd->current_vmcb != svm->vmcb) {
 		sd->current_vmcb = svm->vmcb;
-		indirect_branch_prediction_barrier();
+
+		if (!cpu_feature_enabled(X86_FEATURE_IBPB_ON_VMEXIT))
+			indirect_branch_prediction_barrier();
 	}
 	if (kvm_vcpu_apicv_active(vcpu))
 		avic_vcpu_load(vcpu, cpu);
@@ -1517,6 +1539,15 @@
 	to_svm(vcpu)->vmcb->save.rflags = rflags;
 }
 
+static bool svm_get_if_flag(struct kvm_vcpu *vcpu)
+{
+	struct vmcb *vmcb = to_svm(vcpu)->vmcb;
+
+	return sev_es_guest(vcpu->kvm)
+		? vmcb->control.int_state & SVM_GUEST_INTERRUPT_MASK
+		: kvm_get_rflags(vcpu) & X86_EFLAGS_IF;
+}
+
 static void svm_cache_reg(struct kvm_vcpu *vcpu, enum kvm_reg reg)
 {
 	switch (reg) {
@@ -1709,28 +1740,39 @@
 	vmcb_mark_dirty(svm->vmcb, VMCB_DT);
 }
 
+static bool svm_is_valid_cr0(struct kvm_vcpu *vcpu, unsigned long cr0)
+{
+	return true;
+}
+
 void svm_set_cr0(struct kvm_vcpu *vcpu, unsigned long cr0)
 {
 	struct vcpu_svm *svm = to_svm(vcpu);
 	u64 hcr0 = cr0;
+	bool old_paging = is_paging(vcpu);
 
 #ifdef CONFIG_X86_64
-	if (vcpu->arch.efer & EFER_LME && !vcpu->arch.guest_state_protected) {
+	if (vcpu->arch.efer & EFER_LME) {
 		if (!is_paging(vcpu) && (cr0 & X86_CR0_PG)) {
 			vcpu->arch.efer |= EFER_LMA;
-			svm->vmcb->save.efer |= EFER_LMA | EFER_LME;
+			if (!vcpu->arch.guest_state_protected)
+				svm->vmcb->save.efer |= EFER_LMA | EFER_LME;
 		}
 
 		if (is_paging(vcpu) && !(cr0 & X86_CR0_PG)) {
 			vcpu->arch.efer &= ~EFER_LMA;
-			svm->vmcb->save.efer &= ~(EFER_LMA | EFER_LME);
+			if (!vcpu->arch.guest_state_protected)
+				svm->vmcb->save.efer &= ~(EFER_LMA | EFER_LME);
 		}
 	}
 #endif
 	vcpu->arch.cr0 = cr0;
 
-	if (!npt_enabled)
+	if (!npt_enabled) {
 		hcr0 |= X86_CR0_PG | X86_CR0_WP;
+		if (old_paging != is_paging(vcpu))
+			svm_set_cr4(vcpu, kvm_read_cr4(vcpu));
+	}
 
 	/*
 	 * re-enable caching here because the QEMU bios
@@ -1774,8 +1816,12 @@
 		svm_flush_tlb(vcpu);
 
 	vcpu->arch.cr4 = cr4;
-	if (!npt_enabled)
+	if (!npt_enabled) {
 		cr4 |= X86_CR4_PAE;
+
+		if (!is_paging(vcpu))
+			cr4 &= ~(X86_CR4_SMEP | X86_CR4_SMAP | X86_CR4_PKE);
+	}
 	cr4 |= host_cr4_mce;
 	to_svm(vcpu)->vmcb->save.cr4 = cr4;
 	vmcb_mark_dirty(to_svm(vcpu)->vmcb, VMCB_CR);
@@ -2224,10 +2270,6 @@
 	if (error_code)
 		goto reinject;
 
-	/* All SVM instructions expect page aligned RAX */
-	if (svm->vmcb->save.rax & ~PAGE_MASK)
-		goto reinject;
-
 	/* Decode the instruction for usage later */
 	if (x86_decode_emulated_instruction(vcpu, 0, NULL, 0) != EMULATION_OK)
 		goto reinject;
@@ -2245,8 +2287,13 @@
 		if (!is_guest_mode(vcpu))
 			return kvm_emulate_instruction(vcpu,
 				EMULTYPE_VMWARE_GP | EMULTYPE_NO_DECODE);
-	} else
+	} else {
+		/* All SVM instructions expect page aligned RAX */
+		if (svm->vmcb->save.rax & ~PAGE_MASK)
+			goto reinject;
+
 		return emulate_svm_instr(vcpu, opcode);
+	}
 
 reinject:
 	kvm_queue_exception_e(vcpu, GP_VECTOR, error_code);
@@ -2639,9 +2686,9 @@
 	msr->data = 0;
 
 	switch (msr->index) {
-	case MSR_F10H_DECFG:
-		if (boot_cpu_has(X86_FEATURE_LFENCE_RDTSC))
-			msr->data |= MSR_F10H_DECFG_LFENCE_SERIALIZE;
+	case MSR_AMD64_DE_CFG:
+		if (cpu_feature_enabled(X86_FEATURE_LFENCE_RDTSC))
+			msr->data |= MSR_AMD64_DE_CFG_LFENCE_SERIALIZE;
 		break;
 	case MSR_IA32_PERF_CAPABILITIES:
 		return 0;
@@ -2667,6 +2714,12 @@
 	case MSR_CSTAR:
 		msr_info->data = svm->vmcb01.ptr->save.cstar;
 		break;
+	case MSR_GS_BASE:
+		msr_info->data = svm->vmcb01.ptr->save.gs.base;
+		break;
+	case MSR_FS_BASE:
+		msr_info->data = svm->vmcb01.ptr->save.fs.base;
+		break;
 	case MSR_KERNEL_GS_BASE:
 		msr_info->data = svm->vmcb01.ptr->save.kernel_gs_base;
 		break;
@@ -2750,7 +2803,7 @@
 			msr_info->data = 0x1E;
 		}
 		break;
-	case MSR_F10H_DECFG:
+	case MSR_AMD64_DE_CFG:
 		msr_info->data = svm->msr_decfg;
 		break;
 	default:
@@ -2762,11 +2815,11 @@
 static int svm_complete_emulated_msr(struct kvm_vcpu *vcpu, int err)
 {
 	struct vcpu_svm *svm = to_svm(vcpu);
-	if (!err || !sev_es_guest(vcpu->kvm) || WARN_ON_ONCE(!svm->ghcb))
+	if (!err || !sev_es_guest(vcpu->kvm) || WARN_ON_ONCE(!svm->sev_es.ghcb))
 		return kvm_complete_insn_gp(vcpu, err);
 
-	ghcb_set_sw_exit_info_1(svm->ghcb, 1);
-	ghcb_set_sw_exit_info_2(svm->ghcb,
+	ghcb_set_sw_exit_info_1(svm->sev_es.ghcb, 1);
+	ghcb_set_sw_exit_info_2(svm->sev_es.ghcb,
 				X86_TRAP_GP |
 				SVM_EVTINJ_TYPE_EXEPT |
 				SVM_EVTINJ_VALID);
@@ -2878,6 +2931,12 @@
 	case MSR_CSTAR:
 		svm->vmcb01.ptr->save.cstar = data;
 		break;
+	case MSR_GS_BASE:
+		svm->vmcb01.ptr->save.gs.base = data;
+		break;
+	case MSR_FS_BASE:
+		svm->vmcb01.ptr->save.fs.base = data;
+		break;
 	case MSR_KERNEL_GS_BASE:
 		svm->vmcb01.ptr->save.kernel_gs_base = data;
 		break;
@@ -2950,7 +3009,7 @@
 	case MSR_VM_IGNNE:
 		vcpu_unimpl(vcpu, "unimplemented wrmsr: 0x%x data 0x%llx\n", ecx, data);
 		break;
-	case MSR_F10H_DECFG: {
+	case MSR_AMD64_DE_CFG: {
 		struct kvm_msr_entry msr_entry;
 
 		msr_entry.index = msr->index;
@@ -3332,15 +3391,6 @@
 		return 0;
 	}
 
-	if (is_external_interrupt(svm->vmcb->control.exit_int_info) &&
-	    exit_code != SVM_EXIT_EXCP_BASE + PF_VECTOR &&
-	    exit_code != SVM_EXIT_NPF && exit_code != SVM_EXIT_TASK_SWITCH &&
-	    exit_code != SVM_EXIT_INTR && exit_code != SVM_EXIT_NMI)
-		printk(KERN_ERR "%s: unexpected exit_int_info 0x%x "
-		       "exit_code 0x%x\n",
-		       __func__, svm->vmcb->control.exit_int_info,
-		       exit_code);
-
 	if (exit_fastpath != EXIT_FASTPATH_NONE)
 		return 1;
 
@@ -3394,8 +3444,6 @@
 {
 	struct vcpu_svm *svm = to_svm(vcpu);
 
-	BUG_ON(!(gif_set(svm)));
-
 	trace_kvm_inj_virq(vcpu->arch.interrupt.nr);
 	++vcpu->stat.irq_injections;
 
@@ -3485,14 +3533,7 @@
 	if (!gif_set(svm))
 		return true;
 
-	if (sev_es_guest(vcpu->kvm)) {
-		/*
-		 * SEV-ES guests to not expose RFLAGS. Use the VMCB interrupt mask
-		 * bit to determine the state of the IF flag.
-		 */
-		if (!(vmcb->control.int_state & SVM_GUEST_INTERRUPT_MASK))
-			return true;
-	} else if (is_guest_mode(vcpu)) {
+	if (is_guest_mode(vcpu)) {
 		/* As long as interrupts are being delivered...  */
 		if ((svm->nested.ctl.int_ctl & V_INTR_MASKING_MASK)
 		    ? !(svm->vmcb01.ptr->save.rflags & X86_EFLAGS_IF)
@@ -3503,7 +3544,7 @@
 		if (nested_exit_on_intr(svm))
 			return false;
 	} else {
-		if (!(kvm_get_rflags(vcpu) & X86_EFLAGS_IF))
+		if (!svm_get_if_flag(vcpu))
 			return true;
 	}
 
@@ -3666,6 +3707,18 @@
 	vector = exitintinfo & SVM_EXITINTINFO_VEC_MASK;
 	type = exitintinfo & SVM_EXITINTINFO_TYPE_MASK;
 
+	/*
+	 * If NextRIP isn't enabled, KVM must manually advance RIP prior to
+	 * injecting the soft exception/interrupt.  That advancement needs to
+	 * be unwound if vectoring didn't complete.  Note, the new event may
+	 * not be the injected event, e.g. if KVM injected an INTn, the INTn
+	 * hit a #NP in the guest, and the #NP encountered a #PF, the #NP will
+	 * be the reported vectored event, but RIP still needs to be unwound.
+	 */
+	if (int3_injected && type == SVM_EXITINTINFO_TYPE_EXEPT &&
+	   kvm_is_linear_rip(vcpu, svm->int3_rip))
+		kvm_rip_write(vcpu, kvm_rip_read(vcpu) - int3_injected);
+
 	switch (type) {
 	case SVM_EXITINTINFO_TYPE_NMI:
 		vcpu->arch.nmi_injected = true;
@@ -3679,16 +3732,11 @@
 
 		/*
 		 * In case of software exceptions, do not reinject the vector,
-		 * but re-execute the instruction instead. Rewind RIP first
-		 * if we emulated INT3 before.
+		 * but re-execute the instruction instead.
 		 */
-		if (kvm_exception_is_soft(vector)) {
-			if (vector == BP_VECTOR && int3_injected &&
-			    kvm_is_linear_rip(vcpu, svm->int3_rip))
-				kvm_rip_write(vcpu,
-					      kvm_rip_read(vcpu) - int3_injected);
+		if (kvm_exception_is_soft(vector))
 			break;
-		}
+
 		if (exitintinfo & SVM_EXITINTINFO_VALID_ERR) {
 			u32 err = svm->vmcb->control.exit_int_info_err;
 			kvm_requeue_exception_e(vcpu, vector, err);
@@ -3717,8 +3765,14 @@
 
 static fastpath_t svm_exit_handlers_fastpath(struct kvm_vcpu *vcpu)
 {
-	if (to_svm(vcpu)->vmcb->control.exit_code == SVM_EXIT_MSR &&
-	    to_svm(vcpu)->vmcb->control.exit_info_1)
+	struct vmcb_control_area *control = &to_svm(vcpu)->vmcb->control;
+
+	/*
+	 * Note, the next RIP must be provided as SRCU isn't held, i.e. KVM
+	 * can't read guest memory (dereference memslots) to decode the WRMSR.
+	 */
+	if (control->exit_code == SVM_EXIT_MSR && control->exit_info_1 &&
+	    nrips && control->next_rip)
 		return handle_fastpath_set_msr_irqoff(vcpu);
 
 	return EXIT_FASTPATH_NONE;
@@ -3731,6 +3785,8 @@
 
 	kvm_guest_enter_irqoff();
 
+	amd_clear_divider();
+
 	if (sev_es_guest(vcpu->kvm)) {
 		__svm_sev_es_vcpu_run(vmcb_pa);
 	} else {
@@ -4247,6 +4303,8 @@
 
 static void svm_handle_exit_irqoff(struct kvm_vcpu *vcpu)
 {
+	if (to_svm(vcpu)->vmcb->control.exit_code == SVM_EXIT_INTR)
+		vcpu->arch.at_instruction_boundary = true;
 }
 
 static void svm_sched_in(struct kvm_vcpu *vcpu, int cpu)
@@ -4376,10 +4434,17 @@
 	 * Enter the nested guest now
 	 */
 
+	vmcb_mark_all_dirty(svm->vmcb01.ptr);
+
 	vmcb12 = map.hva;
 	nested_load_control_from_vmcb12(svm, &vmcb12->control);
 	ret = enter_svm_guest_mode(vcpu, vmcb12_gpa, vmcb12, false);
 
+	if (ret)
+		goto unmap_save;
+
+	svm->nested.nested_run_pending = 1;
+
 unmap_save:
 	kvm_vcpu_unmap(vcpu, &map_save, true);
 unmap_map:
@@ -4405,8 +4470,13 @@
 	bool smep, smap, is_user;
 	unsigned long cr4;
 
+	/* Emulation is always possible when KVM has access to all guest state. */
+	if (!sev_guest(vcpu->kvm))
+		return true;
+
 	/*
-	 * When the guest is an SEV-ES guest, emulation is not possible.
+	 * Emulation is impossible for SEV-ES guests as KVM doesn't have access
+	 * to guest register state.
 	 */
 	if (sev_es_guest(vcpu->kvm))
 		return false;
@@ -4454,23 +4524,27 @@
 	if (likely(!insn || insn_len))
 		return true;
 
-	/*
-	 * If RIP is invalid, go ahead with emulation which will cause an
-	 * internal error exit.
-	 */
-	if (!kvm_vcpu_gfn_to_memslot(vcpu, kvm_rip_read(vcpu) >> PAGE_SHIFT))
-		return true;
-
 	cr4 = kvm_read_cr4(vcpu);
 	smep = cr4 & X86_CR4_SMEP;
 	smap = cr4 & X86_CR4_SMAP;
 	is_user = svm_get_cpl(vcpu) == 3;
 	if (smap && (!smep || is_user)) {
-		if (!sev_guest(vcpu->kvm))
-			return true;
-
 		pr_err_ratelimited("KVM: SEV Guest triggered AMD Erratum 1096\n");
-		kvm_make_request(KVM_REQ_TRIPLE_FAULT, vcpu);
+
+		/*
+		 * If the fault occurred in userspace, arbitrarily inject #GP
+		 * to avoid killing the guest and to hopefully avoid confusing
+		 * the guest kernel too much, e.g. injecting #PF would not be
+		 * coherent with respect to the guest's page tables.  Request
+		 * triple fault if the fault occurred in the kernel as there's
+		 * no fault that KVM can inject without confusing the guest.
+		 * In practice, the triple fault is moot as no sane SEV kernel
+		 * will execute from user memory while also running with SMAP=1.
+		 */
+		if (is_user)
+			kvm_inject_gp(vcpu, 0);
+		else
+			kvm_make_request(KVM_REQ_TRIPLE_FAULT, vcpu);
 	}
 
 	return false;
@@ -4549,6 +4623,7 @@
 	.set_segment = svm_set_segment,
 	.get_cpl = svm_get_cpl,
 	.get_cs_db_l_bits = kvm_get_cs_db_l_bits,
+	.is_valid_cr0 = svm_is_valid_cr0,
 	.set_cr0 = svm_set_cr0,
 	.is_valid_cr4 = svm_is_valid_cr4,
 	.set_cr4 = svm_set_cr4,
@@ -4562,6 +4637,7 @@
 	.cache_reg = svm_cache_reg,
 	.get_rflags = svm_get_rflags,
 	.set_rflags = svm_set_rflags,
+	.get_if_flag = svm_get_if_flag,
 
 	.tlb_flush_all = svm_flush_tlb,
 	.tlb_flush_current = svm_flush_tlb,
@@ -4592,7 +4668,6 @@
 	.load_eoi_exitmap = svm_load_eoi_exitmap,
 	.hwapic_irr_update = svm_hwapic_irr_update,
 	.hwapic_isr_update = svm_hwapic_isr_update,
-	.sync_pir_to_irr = kvm_lapic_find_highest_irr,
 	.apicv_post_state_restore = avic_post_state_restore,
 
 	.set_tss_addr = svm_set_tss_addr,
@@ -4635,6 +4710,7 @@
 	.mem_enc_op = svm_mem_enc_op,
 	.mem_enc_reg_region = svm_register_enc_region,
 	.mem_enc_unreg_region = svm_unregister_enc_region,
+	.guest_memory_reclaimed = sev_guest_memory_reclaimed,
 
 	.vm_copy_enc_context_from = svm_vm_copy_asid_from,
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/svm.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/svm.h
@@ -22,6 +22,8 @@
 #include <asm/svm.h>
 #include <asm/sev-common.h>
 
+#include "kvm_cache_regs.h"
+
 #define __sme_page_pa(x) __sme_set(page_to_pfn(x) << PAGE_SHIFT)
 
 #define	IOPM_SIZE PAGE_SIZE * 3
@@ -123,6 +125,22 @@
 	bool initialized;
 };
 
+struct vcpu_sev_es_state {
+	/* SEV-ES support */
+	struct vmcb_save_area *vmsa;
+	struct ghcb *ghcb;
+	u8 valid_bitmap[16];
+	struct kvm_host_map ghcb_map;
+	bool received_first_sipi;
+
+	/* SEV-ES scratch area support */
+	u64 sw_scratch;
+	void *ghcb_sa;
+	u32 ghcb_sa_len;
+	bool ghcb_sa_sync;
+	bool ghcb_sa_free;
+};
+
 struct vcpu_svm {
 	struct kvm_vcpu vcpu;
 	/* vmcb always points at current_vmcb->ptr, it's purely a shorthand. */
@@ -183,17 +201,7 @@
 		DECLARE_BITMAP(write, MAX_DIRECT_ACCESS_MSRS);
 	} shadow_msr_intercept;
 
-	/* SEV-ES support */
-	struct vmcb_save_area *vmsa;
-	struct ghcb *ghcb;
-	struct kvm_host_map ghcb_map;
-	bool received_first_sipi;
-
-	/* SEV-ES scratch area support */
-	void *ghcb_sa;
-	u32 ghcb_sa_len;
-	bool ghcb_sa_sync;
-	bool ghcb_sa_free;
+	struct vcpu_sev_es_state sev_es;
 
 	bool guest_state_loaded;
 };
@@ -461,7 +469,7 @@
 
 int enter_svm_guest_mode(struct kvm_vcpu *vcpu,
 			 u64 vmcb_gpa, struct vmcb *vmcb12, bool from_vmrun);
-void svm_leave_nested(struct vcpu_svm *svm);
+void svm_leave_nested(struct kvm_vcpu *vcpu);
 void svm_free_nested(struct vcpu_svm *svm);
 int svm_allocate_nested(struct vcpu_svm *svm);
 int nested_svm_vmrun(struct kvm_vcpu *vcpu);
@@ -485,6 +493,7 @@
 int nested_svm_exit_special(struct vcpu_svm *svm);
 void nested_load_control_from_vmcb12(struct vcpu_svm *svm,
 				     struct vmcb_control_area *control);
+void __svm_write_tsc_multiplier(u64 multiplier);
 void nested_sync_control_from_vmcb02(struct vcpu_svm *svm);
 void nested_vmcb02_compute_g_pat(struct vcpu_svm *svm);
 void svm_switch_vmcb(struct vcpu_svm *svm, struct kvm_vmcb_info *target_vmcb);
@@ -497,7 +506,7 @@
 #define AVIC_LOGICAL_ID_ENTRY_VALID_BIT			31
 #define AVIC_LOGICAL_ID_ENTRY_VALID_MASK		(1 << 31)
 
-#define AVIC_PHYSICAL_ID_ENTRY_HOST_PHYSICAL_ID_MASK	(0xFFULL)
+#define AVIC_PHYSICAL_ID_ENTRY_HOST_PHYSICAL_ID_MASK	GENMASK_ULL(11, 0)
 #define AVIC_PHYSICAL_ID_ENTRY_BACKING_PAGE_MASK	(0xFFFFFFFFFFULL << 12)
 #define AVIC_PHYSICAL_ID_ENTRY_IS_RUNNING_MASK		(1ULL << 62)
 #define AVIC_PHYSICAL_ID_ENTRY_VALID_MASK		(1ULL << 63)
@@ -553,6 +562,8 @@
 int svm_unregister_enc_region(struct kvm *kvm,
 			      struct kvm_enc_region *range);
 int svm_vm_copy_asid_from(struct kvm *kvm, unsigned int source_fd);
+void sev_guest_memory_reclaimed(struct kvm *kvm);
+
 void pre_sev_run(struct vcpu_svm *svm, int cpu);
 void __init sev_set_cpu_caps(void);
 void __init sev_hardware_setup(void);
@@ -572,4 +583,28 @@
 void __svm_sev_es_vcpu_run(unsigned long vmcb_pa);
 void __svm_vcpu_run(unsigned long vmcb_pa, unsigned long *regs);
 
+#define DEFINE_KVM_GHCB_ACCESSORS(field)						\
+	static __always_inline bool kvm_ghcb_##field##_is_valid(const struct vcpu_svm *svm) \
+	{									\
+		return test_bit(GHCB_BITMAP_IDX(field),				\
+				(unsigned long *)&svm->sev_es.valid_bitmap);	\
+	}									\
+										\
+	static __always_inline u64 kvm_ghcb_get_##field##_if_valid(struct vcpu_svm *svm, struct ghcb *ghcb) \
+	{									\
+		return kvm_ghcb_##field##_is_valid(svm) ? ghcb->save.field : 0;	\
+	}									\
+
+DEFINE_KVM_GHCB_ACCESSORS(cpl)
+DEFINE_KVM_GHCB_ACCESSORS(rax)
+DEFINE_KVM_GHCB_ACCESSORS(rcx)
+DEFINE_KVM_GHCB_ACCESSORS(rdx)
+DEFINE_KVM_GHCB_ACCESSORS(rbx)
+DEFINE_KVM_GHCB_ACCESSORS(rsi)
+DEFINE_KVM_GHCB_ACCESSORS(sw_exit_code)
+DEFINE_KVM_GHCB_ACCESSORS(sw_exit_info_1)
+DEFINE_KVM_GHCB_ACCESSORS(sw_exit_info_2)
+DEFINE_KVM_GHCB_ACCESSORS(sw_scratch)
+DEFINE_KVM_GHCB_ACCESSORS(xcr0)
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/svm_onhyperv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/svm_onhyperv.c
@@ -4,7 +4,6 @@
  */
 
 #include <linux/kvm_host.h>
-#include "kvm_cache_regs.h"
 
 #include <asm/mshyperv.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/svm_onhyperv.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/svm_onhyperv.h
@@ -48,7 +48,7 @@
 		hve->hv_enlightenments_control.enlightened_npt_tlb = 1;
 }
 
-static inline void svm_hv_hardware_setup(void)
+static inline __init void svm_hv_hardware_setup(void)
 {
 	if (npt_enabled &&
 	    ms_hyperv.nested_features & HV_X64_NESTED_ENLIGHTENED_TLB) {
@@ -112,7 +112,7 @@
 {
 }
 
-static inline void svm_hv_hardware_setup(void)
+static inline __init void svm_hv_hardware_setup(void)
 {
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/svm/vmenter.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/svm/vmenter.S
@@ -111,6 +111,18 @@
 #endif
 
 	/*
+	 * Mitigate RETBleed for AMD/Hygon Zen uarch. RET should be
+	 * untrained as soon as we exit the VM and are back to the
+	 * kernel. This should be done before re-enabling interrupts
+	 * because interrupt handlers won't sanitize 'ret' if the return is
+	 * from the kernel.
+	 */
+	UNTRAIN_RET
+
+	/* SRSO */
+	ALTERNATIVE "", "call entry_ibpb", X86_FEATURE_IBPB_ON_VMEXIT
+
+	/*
 	 * Clear all general purpose registers except RSP and RAX to prevent
 	 * speculative use of the guest's values, even those that are reloaded
 	 * via the stack.  In theory, an L1 cache miss when restoring registers
@@ -148,7 +160,7 @@
 	pop %edi
 #endif
 	pop %_ASM_BP
-	ret
+	RET
 
 3:	cmpb $0, kvm_rebooting
 	jne 2b
@@ -190,6 +202,15 @@
 	FILL_RETURN_BUFFER %_ASM_AX, RSB_CLEAR_LOOPS, X86_FEATURE_RETPOLINE
 #endif
 
+	/*
+	 * Mitigate RETBleed for AMD/Hygon Zen uarch. RET should be
+	 * untrained as soon as we exit the VM and are back to the
+	 * kernel. This should be done before re-enabling interrupts
+	 * because interrupt handlers won't sanitize RET if the return is
+	 * from the kernel.
+	 */
+	UNTRAIN_RET
+
 	pop %_ASM_BX
 
 #ifdef CONFIG_X86_64
@@ -202,7 +223,7 @@
 	pop %edi
 #endif
 	pop %_ASM_BP
-	ret
+	RET
 
 3:	cmpb $0, kvm_rebooting
 	jne 2b
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/trace.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/trace.h
@@ -355,25 +355,29 @@
  * Tracepoint for kvm interrupt injection:
  */
 TRACE_EVENT(kvm_inj_exception,
-	TP_PROTO(unsigned exception, bool has_error, unsigned error_code),
-	TP_ARGS(exception, has_error, error_code),
+	TP_PROTO(unsigned exception, bool has_error, unsigned error_code,
+		 bool reinjected),
+	TP_ARGS(exception, has_error, error_code, reinjected),
 
 	TP_STRUCT__entry(
 		__field(	u8,	exception	)
 		__field(	u8,	has_error	)
 		__field(	u32,	error_code	)
+		__field(	bool,	reinjected	)
 	),
 
 	TP_fast_assign(
 		__entry->exception	= exception;
 		__entry->has_error	= has_error;
 		__entry->error_code	= error_code;
+		__entry->reinjected	= reinjected;
 	),
 
-	TP_printk("%s (0x%x)",
+	TP_printk("%s (0x%x)%s",
 		  __print_symbolic(__entry->exception, kvm_trace_sym_exc),
 		  /* FIXME: don't print error_code if not present */
-		  __entry->has_error ? __entry->error_code : 0)
+		  __entry->has_error ? __entry->error_code : 0,
+		  __entry->reinjected ? " [reinjected]" : "")
 );
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/capabilities.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/capabilities.h
@@ -4,7 +4,7 @@
 
 #include <asm/vmx.h>
 
-#include "lapic.h"
+#include "../lapic.h"
 
 extern bool __read_mostly enable_vpid;
 extern bool __read_mostly flexpriority_enabled;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/evmcs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/evmcs.c
@@ -362,6 +362,7 @@
 	case MSR_IA32_VMX_PROCBASED_CTLS2:
 		ctl_high &= ~EVMCS1_UNSUPPORTED_2NDEXEC;
 		break;
+	case MSR_IA32_VMX_TRUE_PINBASED_CTLS:
 	case MSR_IA32_VMX_PINBASED_CTLS:
 		ctl_high &= ~EVMCS1_UNSUPPORTED_PINCTRL;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/evmcs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/evmcs.h
@@ -59,7 +59,9 @@
 	 SECONDARY_EXEC_SHADOW_VMCS |					\
 	 SECONDARY_EXEC_TSC_SCALING |					\
 	 SECONDARY_EXEC_PAUSE_LOOP_EXITING)
-#define EVMCS1_UNSUPPORTED_VMEXIT_CTRL (VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL)
+#define EVMCS1_UNSUPPORTED_VMEXIT_CTRL					\
+	(VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL |				\
+	 VM_EXIT_SAVE_VMX_PREEMPTION_TIMER)
 #define EVMCS1_UNSUPPORTED_VMENTRY_CTRL (VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL)
 #define EVMCS1_UNSUPPORTED_VMFUNC (VMX_VMFUNC_EPTP_SWITCHING)
 
@@ -160,16 +162,6 @@
 	return *(u16 *)((char *)current_evmcs + offset);
 }
 
-static inline void evmcs_touch_msr_bitmap(void)
-{
-	if (unlikely(!current_evmcs))
-		return;
-
-	if (current_evmcs->hv_enlightenments_control.msr_bitmap)
-		current_evmcs->hv_clean_fields &=
-			~HV_VMX_ENLIGHTENED_CLEAN_FIELD_MSR_BITMAP;
-}
-
 static inline void evmcs_load(u64 phys_addr)
 {
 	struct hv_vp_assist_page *vp_ap =
@@ -190,7 +182,6 @@
 static inline u32 evmcs_read32(unsigned long field) { return 0; }
 static inline u16 evmcs_read16(unsigned long field) { return 0; }
 static inline void evmcs_load(u64 phys_addr) {}
-static inline void evmcs_touch_msr_bitmap(void) {}
 #endif /* IS_ENABLED(CONFIG_HYPERV) */
 
 #define EVMPTR_INVALID (-1ULL)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/nested.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/nested.c
@@ -524,29 +524,6 @@
 }
 
 /*
- * Check if MSR is intercepted for L01 MSR bitmap.
- */
-static bool msr_write_intercepted_l01(struct kvm_vcpu *vcpu, u32 msr)
-{
-	unsigned long *msr_bitmap;
-	int f = sizeof(unsigned long);
-
-	if (!cpu_has_vmx_msr_bitmap())
-		return true;
-
-	msr_bitmap = to_vmx(vcpu)->vmcs01.msr_bitmap;
-
-	if (msr <= 0x1fff) {
-		return !!test_bit(msr, msr_bitmap + 0x800 / f);
-	} else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff)) {
-		msr &= 0x1fff;
-		return !!test_bit(msr, msr_bitmap + 0xc00 / f);
-	}
-
-	return true;
-}
-
-/*
  * If a msr is allowed by L0, we should check whether it is allowed by L1.
  * The corresponding bit will be cleared unless both of L0 and L1 allow it.
  */
@@ -599,6 +576,34 @@
 	}
 }
 
+#define BUILD_NVMX_MSR_INTERCEPT_HELPER(rw)					\
+static inline									\
+void nested_vmx_set_msr_##rw##_intercept(struct vcpu_vmx *vmx,			\
+					 unsigned long *msr_bitmap_l1,		\
+					 unsigned long *msr_bitmap_l0, u32 msr)	\
+{										\
+	if (vmx_test_msr_bitmap_##rw(vmx->vmcs01.msr_bitmap, msr) ||		\
+	    vmx_test_msr_bitmap_##rw(msr_bitmap_l1, msr))			\
+		vmx_set_msr_bitmap_##rw(msr_bitmap_l0, msr);			\
+	else									\
+		vmx_clear_msr_bitmap_##rw(msr_bitmap_l0, msr);			\
+}
+BUILD_NVMX_MSR_INTERCEPT_HELPER(read)
+BUILD_NVMX_MSR_INTERCEPT_HELPER(write)
+
+static inline void nested_vmx_set_intercept_for_msr(struct vcpu_vmx *vmx,
+						    unsigned long *msr_bitmap_l1,
+						    unsigned long *msr_bitmap_l0,
+						    u32 msr, int types)
+{
+	if (types & MSR_TYPE_R)
+		nested_vmx_set_msr_read_intercept(vmx, msr_bitmap_l1,
+						  msr_bitmap_l0, msr);
+	if (types & MSR_TYPE_W)
+		nested_vmx_set_msr_write_intercept(vmx, msr_bitmap_l1,
+						   msr_bitmap_l0, msr);
+}
+
 /*
  * Merge L0's and L1's MSR bitmap, return false to indicate that
  * we do not use the hardware.
@@ -606,10 +611,11 @@
 static inline bool nested_vmx_prepare_msr_bitmap(struct kvm_vcpu *vcpu,
 						 struct vmcs12 *vmcs12)
 {
+	struct vcpu_vmx *vmx = to_vmx(vcpu);
 	int msr;
 	unsigned long *msr_bitmap_l1;
-	unsigned long *msr_bitmap_l0 = to_vmx(vcpu)->nested.vmcs02.msr_bitmap;
-	struct kvm_host_map *map = &to_vmx(vcpu)->nested.msr_bitmap_map;
+	unsigned long *msr_bitmap_l0 = vmx->nested.vmcs02.msr_bitmap;
+	struct kvm_host_map *map = &vmx->nested.msr_bitmap_map;
 
 	/* Nothing to do if the MSR bitmap is not in use.  */
 	if (!cpu_has_vmx_msr_bitmap() ||
@@ -660,44 +666,27 @@
 		}
 	}
 
-	/* KVM unconditionally exposes the FS/GS base MSRs to L1. */
+	/*
+	 * Always check vmcs01's bitmap to honor userspace MSR filters and any
+	 * other runtime changes to vmcs01's bitmap, e.g. dynamic pass-through.
+	 */
 #ifdef CONFIG_X86_64
-	nested_vmx_disable_intercept_for_msr(msr_bitmap_l1, msr_bitmap_l0,
-					     MSR_FS_BASE, MSR_TYPE_RW);
+	nested_vmx_set_intercept_for_msr(vmx, msr_bitmap_l1, msr_bitmap_l0,
+					 MSR_FS_BASE, MSR_TYPE_RW);
 
-	nested_vmx_disable_intercept_for_msr(msr_bitmap_l1, msr_bitmap_l0,
-					     MSR_GS_BASE, MSR_TYPE_RW);
+	nested_vmx_set_intercept_for_msr(vmx, msr_bitmap_l1, msr_bitmap_l0,
+					 MSR_GS_BASE, MSR_TYPE_RW);
 
-	nested_vmx_disable_intercept_for_msr(msr_bitmap_l1, msr_bitmap_l0,
-					     MSR_KERNEL_GS_BASE, MSR_TYPE_RW);
+	nested_vmx_set_intercept_for_msr(vmx, msr_bitmap_l1, msr_bitmap_l0,
+					 MSR_KERNEL_GS_BASE, MSR_TYPE_RW);
 #endif
+	nested_vmx_set_intercept_for_msr(vmx, msr_bitmap_l1, msr_bitmap_l0,
+					 MSR_IA32_SPEC_CTRL, MSR_TYPE_RW);
 
-	/*
-	 * Checking the L0->L1 bitmap is trying to verify two things:
-	 *
-	 * 1. L0 gave a permission to L1 to actually passthrough the MSR. This
-	 *    ensures that we do not accidentally generate an L02 MSR bitmap
-	 *    from the L12 MSR bitmap that is too permissive.
-	 * 2. That L1 or L2s have actually used the MSR. This avoids
-	 *    unnecessarily merging of the bitmap if the MSR is unused. This
-	 *    works properly because we only update the L01 MSR bitmap lazily.
-	 *    So even if L0 should pass L1 these MSRs, the L01 bitmap is only
-	 *    updated to reflect this when L1 (or its L2s) actually write to
-	 *    the MSR.
-	 */
-	if (!msr_write_intercepted_l01(vcpu, MSR_IA32_SPEC_CTRL))
-		nested_vmx_disable_intercept_for_msr(
-					msr_bitmap_l1, msr_bitmap_l0,
-					MSR_IA32_SPEC_CTRL,
-					MSR_TYPE_R | MSR_TYPE_W);
-
-	if (!msr_write_intercepted_l01(vcpu, MSR_IA32_PRED_CMD))
-		nested_vmx_disable_intercept_for_msr(
-					msr_bitmap_l1, msr_bitmap_l0,
-					MSR_IA32_PRED_CMD,
-					MSR_TYPE_W);
+	nested_vmx_set_intercept_for_msr(vmx, msr_bitmap_l1, msr_bitmap_l0,
+					 MSR_IA32_PRED_CMD, MSR_TYPE_W);
 
-	kvm_vcpu_unmap(vcpu, &to_vmx(vcpu)->nested.msr_bitmap_map, false);
+	kvm_vcpu_unmap(vcpu, &vmx->nested.msr_bitmap_map, false);
 
 	return true;
 }
@@ -1169,11 +1158,14 @@
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
 
 	/*
-	 * If vmcs12 doesn't use VPID, L1 expects linear and combined mappings
-	 * for *all* contexts to be flushed on VM-Enter/VM-Exit, i.e. it's a
-	 * full TLB flush from the guest's perspective.  This is required even
-	 * if VPID is disabled in the host as KVM may need to synchronize the
-	 * MMU in response to the guest TLB flush.
+	 * If VPID is disabled, then guest TLB accesses use VPID=0, i.e. the
+	 * same VPID as the host, and so architecturally, linear and combined
+	 * mappings for VPID=0 must be flushed at VM-Enter and VM-Exit.  KVM
+	 * emulates L2 sharing L1's VPID=0 by using vpid01 while running L2,
+	 * and so KVM must also emulate TLB flush of VPID=0, i.e. vpid01.  This
+	 * is required if VPID is disabled in KVM, as a TLB flush (there are no
+	 * VPIDs) still occurs from L1's perspective, and KVM may need to
+	 * synchronize the MMU in response to the guest TLB flush.
 	 *
 	 * Note, using TLB_FLUSH_GUEST is correct even if nested EPT is in use.
 	 * EPT is a special snowflake, as guest-physical mappings aren't
@@ -1191,29 +1183,26 @@
 	WARN_ON(!enable_vpid);
 
 	/*
-	 * If VPID is enabled and used by vmc12, but L2 does not have a unique
-	 * TLB tag (ASID), i.e. EPT is disabled and KVM was unable to allocate
-	 * a VPID for L2, flush the current context as the effective ASID is
-	 * common to both L1 and L2.
-	 *
-	 * Defer the flush so that it runs after vmcs02.EPTP has been set by
-	 * KVM_REQ_LOAD_MMU_PGD (if nested EPT is enabled) and to avoid
-	 * redundant flushes further down the nested pipeline.
-	 *
-	 * If a TLB flush isn't required due to any of the above, and vpid12 is
-	 * changing then the new "virtual" VPID (vpid12) will reuse the same
-	 * "real" VPID (vpid02), and so needs to be flushed.  There's no direct
-	 * mapping between vpid02 and vpid12, vpid02 is per-vCPU and reused for
-	 * all nested vCPUs.  Remember, a flush on VM-Enter does not invalidate
-	 * guest-physical mappings, so there is no need to sync the nEPT MMU.
+	 * VPID is enabled and in use by vmcs12.  If vpid12 is changing, then
+	 * emulate a guest TLB flush as KVM does not track vpid12 history nor
+	 * is the VPID incorporated into the MMU context.  I.e. KVM must assume
+	 * that the new vpid12 has never been used and thus represents a new
+	 * guest ASID that cannot have entries in the TLB.
 	 */
-	if (!nested_has_guest_tlb_tag(vcpu)) {
-		kvm_make_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu);
-	} else if (is_vmenter &&
-		   vmcs12->virtual_processor_id != vmx->nested.last_vpid) {
+	if (is_vmenter && vmcs12->virtual_processor_id != vmx->nested.last_vpid) {
 		vmx->nested.last_vpid = vmcs12->virtual_processor_id;
-		vpid_sync_context(nested_get_vpid02(vcpu));
+		kvm_make_request(KVM_REQ_TLB_FLUSH_GUEST, vcpu);
+		return;
 	}
+
+	/*
+	 * If VPID is enabled, used by vmc12, and vpid12 is not changing but
+	 * does not have a unique TLB tag (ASID), i.e. EPT is disabled and
+	 * KVM was unable to allocate a VPID for L2, flush the current context
+	 * as the effective ASID is common to both L1 and L2.
+	 */
+	if (!nested_has_guest_tlb_tag(vcpu))
+		kvm_make_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu);
 }
 
 static bool is_bitwise_subset(u64 superset, u64 subset, u64 mask)
@@ -1231,7 +1220,7 @@
 		BIT_ULL(49) | BIT_ULL(54) | BIT_ULL(55) |
 		/* reserved */
 		BIT_ULL(31) | GENMASK_ULL(47, 45) | GENMASK_ULL(63, 56);
-	u64 vmx_basic = vmx->nested.msrs.basic;
+	u64 vmx_basic = vmcs_config.nested.basic;
 
 	if (!is_bitwise_subset(vmx_basic, data, feature_and_reserved))
 		return -EINVAL;
@@ -1254,36 +1243,42 @@
 	return 0;
 }
 
-static int
-vmx_restore_control_msr(struct vcpu_vmx *vmx, u32 msr_index, u64 data)
+static void vmx_get_control_msr(struct nested_vmx_msrs *msrs, u32 msr_index,
+				u32 **low, u32 **high)
 {
-	u64 supported;
-	u32 *lowp, *highp;
-
 	switch (msr_index) {
 	case MSR_IA32_VMX_TRUE_PINBASED_CTLS:
-		lowp = &vmx->nested.msrs.pinbased_ctls_low;
-		highp = &vmx->nested.msrs.pinbased_ctls_high;
+		*low = &msrs->pinbased_ctls_low;
+		*high = &msrs->pinbased_ctls_high;
 		break;
 	case MSR_IA32_VMX_TRUE_PROCBASED_CTLS:
-		lowp = &vmx->nested.msrs.procbased_ctls_low;
-		highp = &vmx->nested.msrs.procbased_ctls_high;
+		*low = &msrs->procbased_ctls_low;
+		*high = &msrs->procbased_ctls_high;
 		break;
 	case MSR_IA32_VMX_TRUE_EXIT_CTLS:
-		lowp = &vmx->nested.msrs.exit_ctls_low;
-		highp = &vmx->nested.msrs.exit_ctls_high;
+		*low = &msrs->exit_ctls_low;
+		*high = &msrs->exit_ctls_high;
 		break;
 	case MSR_IA32_VMX_TRUE_ENTRY_CTLS:
-		lowp = &vmx->nested.msrs.entry_ctls_low;
-		highp = &vmx->nested.msrs.entry_ctls_high;
+		*low = &msrs->entry_ctls_low;
+		*high = &msrs->entry_ctls_high;
 		break;
 	case MSR_IA32_VMX_PROCBASED_CTLS2:
-		lowp = &vmx->nested.msrs.secondary_ctls_low;
-		highp = &vmx->nested.msrs.secondary_ctls_high;
+		*low = &msrs->secondary_ctls_low;
+		*high = &msrs->secondary_ctls_high;
 		break;
 	default:
 		BUG();
 	}
+}
+
+static int
+vmx_restore_control_msr(struct vcpu_vmx *vmx, u32 msr_index, u64 data)
+{
+	u32 *lowp, *highp;
+	u64 supported;
+
+	vmx_get_control_msr(&vmcs_config.nested, msr_index, &lowp, &highp);
 
 	supported = vmx_control_msr(*lowp, *highp);
 
@@ -1295,6 +1290,7 @@
 	if (!is_bitwise_subset(supported, data, GENMASK_ULL(63, 32)))
 		return -EINVAL;
 
+	vmx_get_control_msr(&vmx->nested.msrs, msr_index, &lowp, &highp);
 	*lowp = data;
 	*highp = data >> 32;
 	return 0;
@@ -1308,10 +1304,8 @@
 		BIT_ULL(28) | BIT_ULL(29) | BIT_ULL(30) |
 		/* reserved */
 		GENMASK_ULL(13, 9) | BIT_ULL(31);
-	u64 vmx_misc;
-
-	vmx_misc = vmx_control_msr(vmx->nested.msrs.misc_low,
-				   vmx->nested.msrs.misc_high);
+	u64 vmx_misc = vmx_control_msr(vmcs_config.nested.misc_low,
+				       vmcs_config.nested.misc_high);
 
 	if (!is_bitwise_subset(vmx_misc, data, feature_and_reserved_bits))
 		return -EINVAL;
@@ -1339,10 +1333,8 @@
 
 static int vmx_restore_vmx_ept_vpid_cap(struct vcpu_vmx *vmx, u64 data)
 {
-	u64 vmx_ept_vpid_cap;
-
-	vmx_ept_vpid_cap = vmx_control_msr(vmx->nested.msrs.ept_caps,
-					   vmx->nested.msrs.vpid_caps);
+	u64 vmx_ept_vpid_cap = vmx_control_msr(vmcs_config.nested.ept_caps,
+					       vmcs_config.nested.vpid_caps);
 
 	/* Every bit is either reserved or a feature bit. */
 	if (!is_bitwise_subset(vmx_ept_vpid_cap, data, -1ULL))
@@ -1353,20 +1345,21 @@
 	return 0;
 }
 
-static int vmx_restore_fixed0_msr(struct vcpu_vmx *vmx, u32 msr_index, u64 data)
+static u64 *vmx_get_fixed0_msr(struct nested_vmx_msrs *msrs, u32 msr_index)
 {
-	u64 *msr;
-
 	switch (msr_index) {
 	case MSR_IA32_VMX_CR0_FIXED0:
-		msr = &vmx->nested.msrs.cr0_fixed0;
-		break;
+		return &msrs->cr0_fixed0;
 	case MSR_IA32_VMX_CR4_FIXED0:
-		msr = &vmx->nested.msrs.cr4_fixed0;
-		break;
+		return &msrs->cr4_fixed0;
 	default:
 		BUG();
 	}
+}
+
+static int vmx_restore_fixed0_msr(struct vcpu_vmx *vmx, u32 msr_index, u64 data)
+{
+	const u64 *msr = vmx_get_fixed0_msr(&vmcs_config.nested, msr_index);
 
 	/*
 	 * 1 bits (which indicates bits which "must-be-1" during VMX operation)
@@ -1375,7 +1368,7 @@
 	if (!is_bitwise_subset(data, *msr, -1ULL))
 		return -EINVAL;
 
-	*msr = data;
+	*vmx_get_fixed0_msr(&vmx->nested.msrs, msr_index) = data;
 	return 0;
 }
 
@@ -1436,7 +1429,7 @@
 		vmx->nested.msrs.vmcs_enum = data;
 		return 0;
 	case MSR_IA32_VMX_VMFUNC:
-		if (data & ~vmx->nested.msrs.vmfunc_controls)
+		if (data & ~vmcs_config.nested.vmfunc_controls)
 			return -EINVAL;
 		vmx->nested.msrs.vmfunc_controls = data;
 		return 0;
@@ -2199,6 +2192,17 @@
 
 	vmcs_write64(VMCS_LINK_POINTER, -1ull);
 
+	/*
+	 * If VPID is disabled, then guest TLB accesses use VPID=0, i.e. the
+	 * same VPID as the host.  Emulate this behavior by using vpid01 for L2
+	 * if VPID is disabled in vmcs12.  Note, if VPID is disabled, VM-Enter
+	 * and VM-Exit are architecturally required to flush VPID=0, but *only*
+	 * VPID=0.  I.e. using vpid02 would be ok (so long as KVM emulates the
+	 * required flushes), but doing so would cause KVM to over-flush.  E.g.
+	 * if L1 runs L2 X with VPID12=1, then runs L2 Y with VPID12 disabled,
+	 * and then runs L2 X again, then KVM can and should retain TLB entries
+	 * for VPID12=1.
+	 */
 	if (enable_vpid) {
 		if (nested_cpu_has_vpid(vmcs12) && vmx->nested.vpid02)
 			vmcs_write16(VIRTUAL_PROCESSOR_ID, vmx->nested.vpid02);
@@ -2283,7 +2287,6 @@
 				  SECONDARY_EXEC_VIRTUAL_INTR_DELIVERY |
 				  SECONDARY_EXEC_APIC_REGISTER_VIRT |
 				  SECONDARY_EXEC_ENABLE_VMFUNC |
-				  SECONDARY_EXEC_TSC_SCALING |
 				  SECONDARY_EXEC_DESC);
 
 		if (nested_cpu_has(vmcs12,
@@ -2324,9 +2327,14 @@
 	 * are emulated by vmx_set_efer() in prepare_vmcs02(), but speculate
 	 * on the related bits (if supported by the CPU) in the hope that
 	 * we can avoid VMWrites during vmx_set_efer().
+	 *
+	 * Similarly, take vmcs01's PERF_GLOBAL_CTRL in the hope that if KVM is
+	 * loading PERF_GLOBAL_CTRL via the VMCS for L1, then KVM will want to
+	 * do the same for L2.
 	 */
 	exec_control = __vm_entry_controls_get(vmcs01);
-	exec_control |= vmcs12->vm_entry_controls;
+	exec_control |= (vmcs12->vm_entry_controls &
+			 ~VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL);
 	exec_control &= ~(VM_ENTRY_IA32E_MODE | VM_ENTRY_LOAD_IA32_EFER);
 	if (cpu_has_load_ia32_efer()) {
 		if (guest_efer & EFER_LMA)
@@ -2622,9 +2630,12 @@
 		vcpu->arch.walk_mmu->inject_page_fault = vmx_inject_page_fault_nested;
 
 	if ((vmcs12->vm_entry_controls & VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL) &&
+	    intel_pmu_has_perf_global_ctrl(vcpu_to_pmu(vcpu)) &&
 	    WARN_ON_ONCE(kvm_set_msr(vcpu, MSR_CORE_PERF_GLOBAL_CTRL,
-				     vmcs12->guest_ia32_perf_global_ctrl)))
+				     vmcs12->guest_ia32_perf_global_ctrl))) {
+		*entry_failure_code = ENTRY_FAIL_DEFAULT;
 		return -EINVAL;
+	}
 
 	kvm_rsp_write(vcpu, vmcs12->guest_rsp);
 	kvm_rip_write(vcpu, vmcs12->guest_rip);
@@ -2865,6 +2876,17 @@
 	return 0;
 }
 
+static int nested_vmx_check_address_space_size(struct kvm_vcpu *vcpu,
+				       struct vmcs12 *vmcs12)
+{
+#ifdef CONFIG_X86_64
+	if (CC(!!(vmcs12->vm_exit_controls & VM_EXIT_HOST_ADDR_SPACE_SIZE) !=
+		!!(vcpu->arch.efer & EFER_LMA)))
+		return -EINVAL;
+#endif
+	return 0;
+}
+
 static int nested_vmx_check_host_state(struct kvm_vcpu *vcpu,
 				       struct vmcs12 *vmcs12)
 {
@@ -2889,18 +2911,16 @@
 		return -EINVAL;
 
 #ifdef CONFIG_X86_64
-	ia32e = !!(vcpu->arch.efer & EFER_LMA);
+	ia32e = !!(vmcs12->vm_exit_controls & VM_EXIT_HOST_ADDR_SPACE_SIZE);
 #else
 	ia32e = false;
 #endif
 
 	if (ia32e) {
-		if (CC(!(vmcs12->vm_exit_controls & VM_EXIT_HOST_ADDR_SPACE_SIZE)) ||
-		    CC(!(vmcs12->host_cr4 & X86_CR4_PAE)))
+		if (CC(!(vmcs12->host_cr4 & X86_CR4_PAE)))
 			return -EINVAL;
 	} else {
-		if (CC(vmcs12->vm_exit_controls & VM_EXIT_HOST_ADDR_SPACE_SIZE) ||
-		    CC(vmcs12->vm_entry_controls & VM_ENTRY_IA32E_MODE) ||
+		if (CC(vmcs12->vm_entry_controls & VM_ENTRY_IA32E_MODE) ||
 		    CC(vmcs12->host_cr4 & X86_CR4_PCIDE) ||
 		    CC((vmcs12->host_rip) >> 32))
 			return -EINVAL;
@@ -2985,7 +3005,7 @@
 					struct vmcs12 *vmcs12,
 					enum vm_entry_failure_code *entry_failure_code)
 {
-	bool ia32e;
+	bool ia32e = !!(vmcs12->vm_entry_controls & VM_ENTRY_IA32E_MODE);
 
 	*entry_failure_code = ENTRY_FAIL_DEFAULT;
 
@@ -3011,6 +3031,13 @@
 					   vmcs12->guest_ia32_perf_global_ctrl)))
 		return -EINVAL;
 
+	if (CC((vmcs12->guest_cr0 & (X86_CR0_PG | X86_CR0_PE)) == X86_CR0_PG))
+		return -EINVAL;
+
+	if (CC(ia32e && !(vmcs12->guest_cr4 & X86_CR4_PAE)) ||
+	    CC(ia32e && !(vmcs12->guest_cr0 & X86_CR0_PG)))
+		return -EINVAL;
+
 	/*
 	 * If the load IA32_EFER VM-entry control is 1, the following checks
 	 * are performed on the field for the IA32_EFER MSR:
@@ -3022,7 +3049,6 @@
 	 */
 	if (to_vmx(vcpu)->nested.nested_run_pending &&
 	    (vmcs12->vm_entry_controls & VM_ENTRY_LOAD_IA32_EFER)) {
-		ia32e = (vmcs12->vm_entry_controls & VM_ENTRY_IA32E_MODE) != 0;
 		if (CC(!kvm_valid_efer(vcpu, vmcs12->guest_ia32_efer)) ||
 		    CC(ia32e != !!(vmcs12->guest_ia32_efer & EFER_LMA)) ||
 		    CC(((vmcs12->guest_cr0 & X86_CR0_PG) &&
@@ -3080,7 +3106,7 @@
 	}
 
 	vm_fail = __vmx_vcpu_run(vmx, (unsigned long *)&vcpu->arch.regs,
-				 vmx->loaded_vmcs->launched);
+				 __vmx_vcpu_run_flags(vmx));
 
 	if (vmx->msr_autoload.host.nr)
 		vmcs_write32(VM_EXIT_MSR_LOAD_COUNT, vmx->msr_autoload.host.nr);
@@ -3360,18 +3386,19 @@
 	};
 	u32 failed_index;
 
-	if (kvm_check_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu))
-		kvm_vcpu_flush_tlb_current(vcpu);
+	kvm_service_local_tlb_flush_requests(vcpu);
 
 	evaluate_pending_interrupts = exec_controls_get(vmx) &
 		(CPU_BASED_INTR_WINDOW_EXITING | CPU_BASED_NMI_WINDOW_EXITING);
 	if (likely(!evaluate_pending_interrupts) && kvm_vcpu_apicv_active(vcpu))
 		evaluate_pending_interrupts |= vmx_has_apicv_interrupt(vcpu);
 
-	if (!(vmcs12->vm_entry_controls & VM_ENTRY_LOAD_DEBUG_CONTROLS))
+	if (!vmx->nested.nested_run_pending ||
+	    !(vmcs12->vm_entry_controls & VM_ENTRY_LOAD_DEBUG_CONTROLS))
 		vmx->nested.vmcs01_debugctl = vmcs_read64(GUEST_IA32_DEBUGCTL);
 	if (kvm_mpx_supported() &&
-		!(vmcs12->vm_entry_controls & VM_ENTRY_LOAD_BNDCFGS))
+	    (!vmx->nested.nested_run_pending ||
+	     !(vmcs12->vm_entry_controls & VM_ENTRY_LOAD_BNDCFGS)))
 		vmx->nested.vmcs01_guest_bndcfgs = vmcs_read64(GUEST_BNDCFGS);
 
 	/*
@@ -3570,6 +3597,9 @@
 	if (nested_vmx_check_controls(vcpu, vmcs12))
 		return nested_vmx_fail(vcpu, VMXERR_ENTRY_INVALID_CONTROL_FIELD);
 
+	if (nested_vmx_check_address_space_size(vcpu, vmcs12))
+		return nested_vmx_fail(vcpu, VMXERR_ENTRY_INVALID_HOST_STATE_FIELD);
+
 	if (nested_vmx_check_host_state(vcpu, vmcs12))
 		return nested_vmx_fail(vcpu, VMXERR_ENTRY_INVALID_HOST_STATE_FIELD);
 
@@ -3679,12 +3709,34 @@
 }
 
 static void vmcs12_save_pending_event(struct kvm_vcpu *vcpu,
-				      struct vmcs12 *vmcs12)
+				      struct vmcs12 *vmcs12,
+				      u32 vm_exit_reason, u32 exit_intr_info)
 {
 	u32 idt_vectoring;
 	unsigned int nr;
 
-	if (vcpu->arch.exception.injected) {
+	/*
+	 * Per the SDM, VM-Exits due to double and triple faults are never
+	 * considered to occur during event delivery, even if the double/triple
+	 * fault is the result of an escalating vectoring issue.
+	 *
+	 * Note, the SDM qualifies the double fault behavior with "The original
+	 * event results in a double-fault exception".  It's unclear why the
+	 * qualification exists since exits due to double fault can occur only
+	 * while vectoring a different exception (injected events are never
+	 * subject to interception), i.e. there's _always_ an original event.
+	 *
+	 * The SDM also uses NMI as a confusing example for the "original event
+	 * causes the VM exit directly" clause.  NMI isn't special in any way,
+	 * the same rule applies to all events that cause an exit directly.
+	 * NMI is an odd choice for the example because NMIs can only occur on
+	 * instruction boundaries, i.e. they _can't_ occur during vectoring.
+	 */
+	if ((u16)vm_exit_reason == EXIT_REASON_TRIPLE_FAULT ||
+	    ((u16)vm_exit_reason == EXIT_REASON_EXCEPTION_NMI &&
+	     is_double_fault(exit_intr_info))) {
+		vmcs12->idt_vectoring_info_field = 0;
+	} else if (vcpu->arch.exception.injected) {
 		nr = vcpu->arch.exception.nr;
 		idt_vectoring = nr | VECTORING_INFO_VALID_MASK;
 
@@ -3717,6 +3769,8 @@
 			idt_vectoring |= INTR_TYPE_EXT_INTR;
 
 		vmcs12->idt_vectoring_info_field = idt_vectoring;
+	} else {
+		vmcs12->idt_vectoring_info_field = 0;
 	}
 }
 
@@ -3792,7 +3846,16 @@
 	u32 intr_info = nr | INTR_INFO_VALID_MASK;
 
 	if (vcpu->arch.exception.has_error_code) {
-		vmcs12->vm_exit_intr_error_code = vcpu->arch.exception.error_code;
+		/*
+		 * Intel CPUs do not generate error codes with bits 31:16 set,
+		 * and more importantly VMX disallows setting bits 31:16 in the
+		 * injected error code for VM-Entry.  Drop the bits to mimic
+		 * hardware and avoid inducing failure on nested VM-Entry if L1
+		 * chooses to inject the exception back to L2.  AMD CPUs _do_
+		 * generate "full" 32-bit error codes, so KVM allows userspace
+		 * to inject exception error codes with bits 31:16 set.
+		 */
+		vmcs12->vm_exit_intr_error_code = (u16)vcpu->arch.exception.error_code;
 		intr_info |= INTR_INFO_DELIVER_CODE_MASK;
 	}
 
@@ -4186,12 +4249,12 @@
 	if (to_vmx(vcpu)->exit_reason.enclave_mode)
 		vmcs12->vm_exit_reason |= VMX_EXIT_REASONS_SGX_ENCLAVE_MODE;
 	vmcs12->exit_qualification = exit_qualification;
-	vmcs12->vm_exit_intr_info = exit_intr_info;
-
-	vmcs12->idt_vectoring_info_field = 0;
-	vmcs12->vm_exit_instruction_len = vmcs_read32(VM_EXIT_INSTRUCTION_LEN);
-	vmcs12->vmx_instruction_info = vmcs_read32(VMX_INSTRUCTION_INFO);
 
+	/*
+	 * On VM-Exit due to a failed VM-Entry, the VMCS isn't marked launched
+	 * and only EXIT_REASON and EXIT_QUALIFICATION are updated, all other
+	 * exit info fields are unmodified.
+	 */
 	if (!(vmcs12->vm_exit_reason & VMX_EXIT_REASONS_FAILED_VMENTRY)) {
 		vmcs12->launch_state = 1;
 
@@ -4203,7 +4266,12 @@
 		 * Transfer the event that L0 or L1 may wanted to inject into
 		 * L2 to IDT_VECTORING_INFO_FIELD.
 		 */
-		vmcs12_save_pending_event(vcpu, vmcs12);
+		vmcs12_save_pending_event(vcpu, vmcs12,
+					  vm_exit_reason, exit_intr_info);
+
+		vmcs12->vm_exit_intr_info = exit_intr_info;
+		vmcs12->vm_exit_instruction_len = vmcs_read32(VM_EXIT_INSTRUCTION_LEN);
+		vmcs12->vmx_instruction_info = vmcs_read32(VMX_INSTRUCTION_INFO);
 
 		/*
 		 * According to spec, there's no need to store the guest's
@@ -4217,14 +4285,6 @@
 			nested_vmx_abort(vcpu,
 					 VMX_ABORT_SAVE_GUEST_MSR_FAIL);
 	}
-
-	/*
-	 * Drop what we picked up for L2 via vmx_complete_interrupts. It is
-	 * preserved above and would only end up incorrectly in L1.
-	 */
-	vcpu->arch.nmi_injected = false;
-	kvm_clear_exception_queue(vcpu);
-	kvm_clear_interrupt_queue(vcpu);
 }
 
 /*
@@ -4296,7 +4356,8 @@
 		vmcs_write64(GUEST_IA32_PAT, vmcs12->host_ia32_pat);
 		vcpu->arch.pat = vmcs12->host_ia32_pat;
 	}
-	if (vmcs12->vm_exit_controls & VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL)
+	if ((vmcs12->vm_exit_controls & VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL) &&
+	    intel_pmu_has_perf_global_ctrl(vcpu_to_pmu(vcpu)))
 		WARN_ON_ONCE(kvm_set_msr(vcpu, MSR_CORE_PERF_GLOBAL_CTRL,
 					 vmcs12->host_ia32_perf_global_ctrl));
 
@@ -4502,9 +4563,6 @@
 	/* trying to cancel vmlaunch/vmresume is a bug */
 	WARN_ON_ONCE(vmx->nested.nested_run_pending);
 
-	/* Similarly, triple faults in L2 should never escape. */
-	WARN_ON_ONCE(kvm_check_request(KVM_REQ_TRIPLE_FAULT, vcpu));
-
 	if (kvm_check_request(KVM_REQ_GET_NESTED_STATE_PAGES, vcpu)) {
 		/*
 		 * KVM_REQ_GET_NESTED_STATE_PAGES is also used to map
@@ -4515,9 +4573,8 @@
 		(void)nested_get_evmcs_page(vcpu);
 	}
 
-	/* Service the TLB flush request for L2 before switching to L1. */
-	if (kvm_check_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu))
-		kvm_vcpu_flush_tlb_current(vcpu);
+	/* Service pending TLB flush requests for L2 before switching to L1. */
+	kvm_service_local_tlb_flush_requests(vcpu);
 
 	/*
 	 * VCPU_EXREG_PDPTR will be clobbered in arch/x86/kvm/vmx/vmx.h between
@@ -4567,8 +4624,30 @@
 		WARN_ON_ONCE(nested_early_check);
 	}
 
+	/*
+	 * Drop events/exceptions that were queued for re-injection to L2
+	 * (picked up via vmx_complete_interrupts()), as well as exceptions
+	 * that were pending for L2.  Note, this must NOT be hoisted above
+	 * prepare_vmcs12(), events/exceptions queued for re-injection need to
+	 * be captured in vmcs12 (see vmcs12_save_pending_event()).
+	 */
+	vcpu->arch.nmi_injected = false;
+	kvm_clear_exception_queue(vcpu);
+	kvm_clear_interrupt_queue(vcpu);
+
 	vmx_switch_vmcs(vcpu, &vmx->vmcs01);
 
+	/*
+	 * If IBRS is advertised to the vCPU, KVM must flush the indirect
+	 * branch predictors when transitioning from L2 to L1, as L1 expects
+	 * hardware (KVM in this case) to provide separate predictor modes.
+	 * Bare metal isolates VMX root (host) from VMX non-root (guest), but
+	 * doesn't isolate different VMCSs, i.e. in this case, doesn't provide
+	 * separate modes for L2 vs L1.
+	 */
+	if (guest_cpuid_has(vcpu, X86_FEATURE_SPEC_CTRL))
+		indirect_branch_prediction_barrier();
+
 	/* Update any VMCS fields that might have changed while L2 ran */
 	vmcs_write32(VM_EXIT_MSR_LOAD_COUNT, vmx->msr_autoload.host.nr);
 	vmcs_write32(VM_ENTRY_MSR_LOAD_COUNT, vmx->msr_autoload.guest.nr);
@@ -4603,6 +4682,11 @@
 		kvm_make_request(KVM_REQ_APIC_PAGE_RELOAD, vcpu);
 	}
 
+	if (vmx->nested.update_vmcs01_apicv_status) {
+		vmx->nested.update_vmcs01_apicv_status = false;
+		kvm_make_request(KVM_REQ_APICV_UPDATE, vcpu);
+	}
+
 	if ((vm_exit_reason != -1) &&
 	    (enable_shadow_vmcs || evmptr_is_valid(vmx->nested.hv_evmcs_vmptr)))
 		vmx->nested.need_vmcs12_to_shadow_sync = true;
@@ -4917,20 +5001,36 @@
 		| FEAT_CTL_VMX_ENABLED_OUTSIDE_SMX;
 
 	/*
-	 * The Intel VMX Instruction Reference lists a bunch of bits that are
-	 * prerequisite to running VMXON, most notably cr4.VMXE must be set to
-	 * 1 (see vmx_is_valid_cr4() for when we allow the guest to set this).
-	 * Otherwise, we should fail with #UD.  But most faulting conditions
-	 * have already been checked by hardware, prior to the VM-exit for
-	 * VMXON.  We do test guest cr4.VMXE because processor CR4 always has
-	 * that bit set to 1 in non-root mode.
+	 * Manually check CR4.VMXE checks, KVM must force CR4.VMXE=1 to enter
+	 * the guest and so cannot rely on hardware to perform the check,
+	 * which has higher priority than VM-Exit (see Intel SDM's pseudocode
+	 * for VMXON).
+	 *
+	 * Rely on hardware for the other pre-VM-Exit checks, CR0.PE=1, !VM86
+	 * and !COMPATIBILITY modes.  For an unrestricted guest, KVM doesn't
+	 * force any of the relevant guest state.  For a restricted guest, KVM
+	 * does force CR0.PE=1, but only to also force VM86 in order to emulate
+	 * Real Mode, and so there's no need to check CR0.PE manually.
 	 */
 	if (!kvm_read_cr4_bits(vcpu, X86_CR4_VMXE)) {
 		kvm_queue_exception(vcpu, UD_VECTOR);
 		return 1;
 	}
 
-	/* CPL=0 must be checked manually. */
+	/*
+	 * The CPL is checked for "not in VMX operation" and for "in VMX root",
+	 * and has higher priority than the VM-Fail due to being post-VMXON,
+	 * i.e. VMXON #GPs outside of VMX non-root if CPL!=0.  In VMX non-root,
+	 * VMXON causes VM-Exit and KVM unconditionally forwards VMXON VM-Exits
+	 * from L2 to L1, i.e. there's no need to check for the vCPU being in
+	 * VMX non-root.
+	 *
+	 * Forwarding the VM-Exit unconditionally, i.e. without performing the
+	 * #UD checks (see above), is functionally ok because KVM doesn't allow
+	 * L1 to run L2 without CR4.VMXE=0, and because KVM never modifies L2's
+	 * CR0 or CR4, i.e. it's L2's responsibility to emulate #UDs that are
+	 * missed by hardware due to shadowing CR0 and/or CR4.
+	 */
 	if (vmx_get_cpl(vcpu)) {
 		kvm_inject_gp(vcpu, 0);
 		return 1;
@@ -4939,6 +5039,17 @@
 	if (vmx->nested.vmxon)
 		return nested_vmx_fail(vcpu, VMXERR_VMXON_IN_VMX_ROOT_OPERATION);
 
+	/*
+	 * Invalid CR0/CR4 generates #GP.  These checks are performed if and
+	 * only if the vCPU isn't already in VMX operation, i.e. effectively
+	 * have lower priority than the VM-Fail above.
+	 */
+	if (!nested_host_cr0_valid(vcpu, kvm_read_cr0(vcpu)) ||
+	    !nested_host_cr4_valid(vcpu, kvm_read_cr4(vcpu))) {
+		kvm_inject_gp(vcpu, 0);
+		return 1;
+	}
+
 	if ((vmx->msr_ia32_feature_control & VMXON_NEEDED_FEATURES)
 			!= VMXON_NEEDED_FEATURES) {
 		kvm_inject_gp(vcpu, 0);
@@ -5494,6 +5605,12 @@
 		return nested_vmx_fail(vcpu,
 			VMXERR_INVALID_OPERAND_TO_INVEPT_INVVPID);
 
+	/*
+	 * Always flush the effective vpid02, i.e. never flush the current VPID
+	 * and never explicitly flush vpid01.  INVVPID targets a VPID, not a
+	 * VMCS, and so whether or not the current vmcs12 has VPID enabled is
+	 * irrelevant (and there may not be a loaded vmcs12).
+	 */
 	vpid02 = nested_get_vpid02(vcpu);
 	switch (type) {
 	case VMX_VPID_EXTENT_INDIVIDUAL_ADDR:
@@ -6218,9 +6335,6 @@
 	return kvm_state.size;
 }
 
-/*
- * Forcibly leave nested mode in order to be able to reset the VCPU later on.
- */
 void vmx_leave_nested(struct kvm_vcpu *vcpu)
 {
 	if (is_guest_mode(vcpu)) {
@@ -6589,7 +6703,8 @@
 		SECONDARY_EXEC_ENABLE_INVPCID |
 		SECONDARY_EXEC_RDSEED_EXITING |
 		SECONDARY_EXEC_XSAVES |
-		SECONDARY_EXEC_TSC_SCALING;
+		SECONDARY_EXEC_TSC_SCALING |
+		SECONDARY_EXEC_ENABLE_USR_WAIT_PAUSE;
 
 	/*
 	 * We can emulate "VMCS shadowing," even if the hardware
@@ -6697,6 +6812,9 @@
 	rdmsrl(MSR_IA32_VMX_CR0_FIXED1, msrs->cr0_fixed1);
 	rdmsrl(MSR_IA32_VMX_CR4_FIXED1, msrs->cr4_fixed1);
 
+	if (vmx_umip_emulated())
+		msrs->cr4_fixed1 |= X86_CR4_UMIP;
+
 	msrs->vmcs_enum = nested_vmx_calc_vmcs_enum_msr();
 }
 
@@ -6750,6 +6868,7 @@
 }
 
 struct kvm_x86_nested_ops vmx_nested_ops = {
+	.leave_nested = vmx_leave_nested,
 	.check_events = vmx_check_nested_events,
 	.hv_timer_pending = nested_vmx_preemption_timer_pending,
 	.triple_fault = nested_vmx_triple_fault,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/nested.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/nested.h
@@ -280,7 +280,8 @@
 	u64 fixed0 = to_vmx(vcpu)->nested.msrs.cr4_fixed0;
 	u64 fixed1 = to_vmx(vcpu)->nested.msrs.cr4_fixed1;
 
-	return fixed_bits_valid(val, fixed0, fixed1);
+	return fixed_bits_valid(val, fixed0, fixed1) &&
+	       __kvm_is_valid_cr4(vcpu, val);
 }
 
 /* No difference in the restrictions on guest and host CR4 in VMX operation. */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/pmu_intel.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/pmu_intel.c
@@ -68,10 +68,11 @@
 		reprogram_counter(pmu, bit);
 }
 
-static unsigned intel_find_arch_event(struct kvm_pmu *pmu,
-				      u8 event_select,
-				      u8 unit_mask)
+static unsigned int intel_pmc_perf_hw_id(struct kvm_pmc *pmc)
 {
+	struct kvm_pmu *pmu = pmc_to_pmu(pmc);
+	u8 event_select = pmc->eventsel & ARCH_PERFMON_EVENTSEL_EVENT;
+	u8 unit_mask = (pmc->eventsel & ARCH_PERFMON_EVENTSEL_UMASK) >> 8;
 	int i;
 
 	for (i = 0; i < ARRAY_SIZE(intel_arch_events); i++)
@@ -103,6 +104,9 @@
 {
 	struct kvm_pmu *pmu = pmc_to_pmu(pmc);
 
+	if (!intel_pmu_has_perf_global_ctrl(pmu))
+		return true;
+
 	return test_bit(pmc->idx, (unsigned long *)&pmu->global_ctrl);
 }
 
@@ -218,7 +222,7 @@
 	case MSR_CORE_PERF_GLOBAL_STATUS:
 	case MSR_CORE_PERF_GLOBAL_CTRL:
 	case MSR_CORE_PERF_GLOBAL_OVF_CTRL:
-		ret = pmu->version > 1;
+		return intel_pmu_has_perf_global_ctrl(pmu);
 		break;
 	default:
 		ret = get_gp_pmc(pmu, msr, MSR_IA32_PERFCTR0) ||
@@ -395,12 +399,13 @@
 	struct kvm_pmc *pmc;
 	u32 msr = msr_info->index;
 	u64 data = msr_info->data;
+	u64 reserved_bits;
 
 	switch (msr) {
 	case MSR_CORE_PERF_FIXED_CTR_CTRL:
 		if (pmu->fixed_ctr_ctrl == data)
 			return 0;
-		if (!(data & 0xfffffffffffff444ull)) {
+		if (!(data & pmu->fixed_ctr_ctrl_mask)) {
 			reprogram_fixed_counters(pmu, data);
 			return 0;
 		}
@@ -437,20 +442,20 @@
 			    !(msr & MSR_PMC_FULL_WIDTH_BIT))
 				data = (s64)(s32)data;
 			pmc->counter += data - pmc_read_counter(pmc);
-			if (pmc->perf_event && !pmc->is_paused)
-				perf_event_period(pmc->perf_event,
-						  get_sample_period(pmc, data));
+			pmc_update_sample_period(pmc);
 			return 0;
 		} else if ((pmc = get_fixed_pmc(pmu, msr))) {
 			pmc->counter += data - pmc_read_counter(pmc);
-			if (pmc->perf_event && !pmc->is_paused)
-				perf_event_period(pmc->perf_event,
-						  get_sample_period(pmc, data));
+			pmc_update_sample_period(pmc);
 			return 0;
 		} else if ((pmc = get_gp_pmc(pmu, msr, MSR_P6_EVNTSEL0))) {
 			if (data == pmc->eventsel)
 				return 0;
-			if (!(data & pmu->reserved_bits)) {
+			reserved_bits = pmu->reserved_bits;
+			if ((pmc->idx == 2) &&
+			    (pmu->raw_event_mask & HSW_IN_TX_CHECKPOINTED))
+				reserved_bits ^= HSW_IN_TX_CHECKPOINTED;
+			if (!(data & reserved_bits)) {
 				reprogram_gp_counter(pmc, data);
 				return 0;
 			}
@@ -470,6 +475,7 @@
 	struct kvm_cpuid_entry2 *entry;
 	union cpuid10_eax eax;
 	union cpuid10_edx edx;
+	int i;
 
 	pmu->nr_arch_gp_counters = 0;
 	pmu->nr_arch_fixed_counters = 0;
@@ -477,6 +483,10 @@
 	pmu->counter_bitmask[KVM_PMC_FIXED] = 0;
 	pmu->version = 0;
 	pmu->reserved_bits = 0xffffffff00200000ull;
+	pmu->raw_event_mask = X86_RAW_EVENT_MASK;
+	pmu->global_ctrl_mask = ~0ull;
+	pmu->global_ovf_ctrl_mask = ~0ull;
+	pmu->fixed_ctr_ctrl_mask = ~0ull;
 
 	entry = kvm_find_cpuid_entry(vcpu, 0xa, 0);
 	if (!entry)
@@ -510,6 +520,8 @@
 			((u64)1 << edx.split.bit_width_fixed) - 1;
 	}
 
+	for (i = 0; i < pmu->nr_arch_fixed_counters; i++)
+		pmu->fixed_ctr_ctrl_mask &= ~(0xbull << (i * 4));
 	pmu->global_ctrl = ((1ull << pmu->nr_arch_gp_counters) - 1) |
 		(((1ull << pmu->nr_arch_fixed_counters) - 1) << INTEL_PMC_IDX_FIXED);
 	pmu->global_ctrl_mask = ~pmu->global_ctrl;
@@ -523,8 +535,10 @@
 	entry = kvm_find_cpuid_entry(vcpu, 7, 0);
 	if (entry &&
 	    (boot_cpu_has(X86_FEATURE_HLE) || boot_cpu_has(X86_FEATURE_RTM)) &&
-	    (entry->ebx & (X86_FEATURE_HLE|X86_FEATURE_RTM)))
-		pmu->reserved_bits ^= HSW_IN_TX|HSW_IN_TX_CHECKPOINTED;
+	    (entry->ebx & (X86_FEATURE_HLE|X86_FEATURE_RTM))) {
+		pmu->reserved_bits ^= HSW_IN_TX;
+		pmu->raw_event_mask |= (HSW_IN_TX|HSW_IN_TX_CHECKPOINTED);
+	}
 
 	bitmap_set(pmu->all_valid_pmc_idx,
 		0, pmu->nr_arch_gp_counters);
@@ -706,7 +720,7 @@
 }
 
 struct kvm_pmu_ops intel_pmu_ops = {
-	.find_arch_event = intel_find_arch_event,
+	.pmc_perf_hw_id = intel_pmc_perf_hw_id,
 	.find_fixed_event = intel_find_fixed_event,
 	.pmc_is_enabled = intel_pmc_is_enabled,
 	.pmc_idx_to_pmc = intel_pmc_idx_to_pmc,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/posted_intr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/posted_intr.c
@@ -5,6 +5,7 @@
 #include <asm/cpu.h>
 
 #include "lapic.h"
+#include "irq.h"
 #include "posted_intr.h"
 #include "trace.h"
 #include "vmx.h"
@@ -14,7 +15,7 @@
  * can find which vCPU should be waken up.
  */
 static DEFINE_PER_CPU(struct list_head, blocked_vcpu_on_cpu);
-static DEFINE_PER_CPU(spinlock_t, blocked_vcpu_on_cpu_lock);
+static DEFINE_PER_CPU(raw_spinlock_t, blocked_vcpu_on_cpu_lock);
 
 static inline struct pi_desc *vcpu_to_pi_desc(struct kvm_vcpu *vcpu)
 {
@@ -50,7 +51,7 @@
 
 	/* The full case.  */
 	do {
-		old.control = new.control = pi_desc->control;
+		old.control = new.control = READ_ONCE(pi_desc->control);
 
 		dest = cpu_physical_id(cpu);
 
@@ -77,13 +78,18 @@
 		pi_set_on(pi_desc);
 }
 
+static bool vmx_can_use_vtd_pi(struct kvm *kvm)
+{
+	return irqchip_in_kernel(kvm) && enable_apicv &&
+		kvm_arch_has_assigned_device(kvm) &&
+		irq_remapping_cap(IRQ_POSTING_CAP);
+}
+
 void vmx_vcpu_pi_put(struct kvm_vcpu *vcpu)
 {
 	struct pi_desc *pi_desc = vcpu_to_pi_desc(vcpu);
 
-	if (!kvm_arch_has_assigned_device(vcpu->kvm) ||
-		!irq_remapping_cap(IRQ_POSTING_CAP)  ||
-		!kvm_vcpu_apicv_active(vcpu))
+	if (!vmx_can_use_vtd_pi(vcpu->kvm))
 		return;
 
 	/* Set SN when the vCPU is preempted */
@@ -98,7 +104,7 @@
 	unsigned int dest;
 
 	do {
-		old.control = new.control = pi_desc->control;
+		old.control = new.control = READ_ONCE(pi_desc->control);
 		WARN(old.nv != POSTED_INTR_WAKEUP_VECTOR,
 		     "Wakeup handler not enabled while the VCPU is blocked\n");
 
@@ -115,9 +121,9 @@
 			   new.control) != old.control);
 
 	if (!WARN_ON_ONCE(vcpu->pre_pcpu == -1)) {
-		spin_lock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
+		raw_spin_lock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
 		list_del(&vcpu->blocked_vcpu_list);
-		spin_unlock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
+		raw_spin_unlock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
 		vcpu->pre_pcpu = -1;
 	}
 }
@@ -141,24 +147,23 @@
 	struct pi_desc old, new;
 	struct pi_desc *pi_desc = vcpu_to_pi_desc(vcpu);
 
-	if (!kvm_arch_has_assigned_device(vcpu->kvm) ||
-		!irq_remapping_cap(IRQ_POSTING_CAP)  ||
-		!kvm_vcpu_apicv_active(vcpu))
+	if (!vmx_can_use_vtd_pi(vcpu->kvm) ||
+	    vmx_interrupt_blocked(vcpu))
 		return 0;
 
 	WARN_ON(irqs_disabled());
 	local_irq_disable();
 	if (!WARN_ON_ONCE(vcpu->pre_pcpu != -1)) {
 		vcpu->pre_pcpu = vcpu->cpu;
-		spin_lock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
+		raw_spin_lock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
 		list_add_tail(&vcpu->blocked_vcpu_list,
 			      &per_cpu(blocked_vcpu_on_cpu,
 				       vcpu->pre_pcpu));
-		spin_unlock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
+		raw_spin_unlock(&per_cpu(blocked_vcpu_on_cpu_lock, vcpu->pre_pcpu));
 	}
 
 	do {
-		old.control = new.control = pi_desc->control;
+		old.control = new.control = READ_ONCE(pi_desc->control);
 
 		WARN((pi_desc->sn == 1),
 		     "Warning: SN field of posted-interrupts "
@@ -211,7 +216,7 @@
 	struct kvm_vcpu *vcpu;
 	int cpu = smp_processor_id();
 
-	spin_lock(&per_cpu(blocked_vcpu_on_cpu_lock, cpu));
+	raw_spin_lock(&per_cpu(blocked_vcpu_on_cpu_lock, cpu));
 	list_for_each_entry(vcpu, &per_cpu(blocked_vcpu_on_cpu, cpu),
 			blocked_vcpu_list) {
 		struct pi_desc *pi_desc = vcpu_to_pi_desc(vcpu);
@@ -219,13 +224,13 @@
 		if (pi_test_on(pi_desc) == 1)
 			kvm_vcpu_kick(vcpu);
 	}
-	spin_unlock(&per_cpu(blocked_vcpu_on_cpu_lock, cpu));
+	raw_spin_unlock(&per_cpu(blocked_vcpu_on_cpu_lock, cpu));
 }
 
 void __init pi_init_cpu(int cpu)
 {
 	INIT_LIST_HEAD(&per_cpu(blocked_vcpu_on_cpu, cpu));
-	spin_lock_init(&per_cpu(blocked_vcpu_on_cpu_lock, cpu));
+	raw_spin_lock_init(&per_cpu(blocked_vcpu_on_cpu_lock, cpu));
 }
 
 bool pi_has_pending_interrupt(struct kvm_vcpu *vcpu)
@@ -270,9 +275,7 @@
 	struct vcpu_data vcpu_info;
 	int idx, ret = 0;
 
-	if (!kvm_arch_has_assigned_device(kvm) ||
-	    !irq_remapping_cap(IRQ_POSTING_CAP) ||
-	    !kvm_vcpu_apicv_active(kvm->vcpus[0]))
+	if (!vmx_can_use_vtd_pi(kvm))
 		return 0;
 
 	idx = srcu_read_lock(&kvm->irq_srcu);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/run_flags.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/run_flags.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __KVM_X86_VMX_RUN_FLAGS_H
+#define __KVM_X86_VMX_RUN_FLAGS_H
+
+#define VMX_RUN_VMRESUME_SHIFT		0
+#define VMX_RUN_SAVE_SPEC_CTRL_SHIFT	1
+
+#define VMX_RUN_VMRESUME		BIT(VMX_RUN_VMRESUME_SHIFT)
+#define VMX_RUN_SAVE_SPEC_CTRL		BIT(VMX_RUN_SAVE_SPEC_CTRL_SHIFT)
+
+#endif /* __KVM_X86_VMX_RUN_FLAGS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/sgx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/sgx.c
@@ -188,8 +188,10 @@
 	/* Enforce CPUID restriction on max enclave size. */
 	max_size_log2 = (attributes & SGX_ATTR_MODE64BIT) ? sgx_12_0->edx >> 8 :
 							    sgx_12_0->edx;
-	if (size >= BIT_ULL(max_size_log2))
+	if (size >= BIT_ULL(max_size_log2)) {
 		kvm_inject_gp(vcpu, 0);
+		return 1;
+	}
 
 	/*
 	 * sgx_virt_ecreate() returns:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/vmcs.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/vmcs.h
@@ -104,6 +104,11 @@
 	return is_exception_n(intr_info, BP_VECTOR);
 }
 
+static inline bool is_double_fault(u32 intr_info)
+{
+	return is_exception_n(intr_info, DF_VECTOR);
+}
+
 static inline bool is_page_fault(u32 intr_info)
 {
 	return is_exception_n(intr_info, PF_VECTOR);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/vmenter.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/vmenter.S
@@ -1,10 +1,13 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 #include <linux/linkage.h>
 #include <asm/asm.h>
+#include <asm/asm-offsets.h>
 #include <asm/bitsperlong.h>
 #include <asm/kvm_vcpu_regs.h>
 #include <asm/nospec-branch.h>
+#include <asm/percpu.h>
 #include <asm/segment.h>
+#include "run_flags.h"
 
 #define WORD_SIZE (BITS_PER_LONG / 8)
 
@@ -31,72 +34,11 @@
 .section .noinstr.text, "ax"
 
 /**
- * vmx_vmenter - VM-Enter the current loaded VMCS
- *
- * %RFLAGS.ZF:	!VMCS.LAUNCHED, i.e. controls VMLAUNCH vs. VMRESUME
- *
- * Returns:
- *	%RFLAGS.CF is set on VM-Fail Invalid
- *	%RFLAGS.ZF is set on VM-Fail Valid
- *	%RFLAGS.{CF,ZF} are cleared on VM-Success, i.e. VM-Exit
- *
- * Note that VMRESUME/VMLAUNCH fall-through and return directly if
- * they VM-Fail, whereas a successful VM-Enter + VM-Exit will jump
- * to vmx_vmexit.
- */
-SYM_FUNC_START_LOCAL(vmx_vmenter)
-	/* EFLAGS.ZF is set if VMCS.LAUNCHED == 0 */
-	je 2f
-
-1:	vmresume
-	ret
-
-2:	vmlaunch
-	ret
-
-3:	cmpb $0, kvm_rebooting
-	je 4f
-	ret
-4:	ud2
-
-	_ASM_EXTABLE(1b, 3b)
-	_ASM_EXTABLE(2b, 3b)
-
-SYM_FUNC_END(vmx_vmenter)
-
-/**
- * vmx_vmexit - Handle a VMX VM-Exit
- *
- * Returns:
- *	%RFLAGS.{CF,ZF} are cleared on VM-Success, i.e. VM-Exit
- *
- * This is vmx_vmenter's partner in crime.  On a VM-Exit, control will jump
- * here after hardware loads the host's state, i.e. this is the destination
- * referred to by VMCS.HOST_RIP.
- */
-SYM_FUNC_START(vmx_vmexit)
-#ifdef CONFIG_RETPOLINE
-	ALTERNATIVE "jmp .Lvmexit_skip_rsb", "", X86_FEATURE_RETPOLINE
-	/* Preserve guest's RAX, it's used to stuff the RSB. */
-	push %_ASM_AX
-
-	/* IMPORTANT: Stuff the RSB immediately after VM-Exit, before RET! */
-	FILL_RETURN_BUFFER %_ASM_AX, RSB_CLEAR_LOOPS, X86_FEATURE_RETPOLINE
-
-	/* Clear RFLAGS.CF and RFLAGS.ZF to preserve VM-Exit, i.e. !VM-Fail. */
-	or $1, %_ASM_AX
-
-	pop %_ASM_AX
-.Lvmexit_skip_rsb:
-#endif
-	ret
-SYM_FUNC_END(vmx_vmexit)
-
-/**
  * __vmx_vcpu_run - Run a vCPU via a transition to VMX guest mode
- * @vmx:	struct vcpu_vmx * (forwarded to vmx_update_host_rsp)
+ * @vmx:	struct vcpu_vmx *
  * @regs:	unsigned long * (to guest registers)
- * @launched:	%true if the VMCS has been launched
+ * @flags:	VMX_RUN_VMRESUME:	use VMRESUME instead of VMLAUNCH
+ *		VMX_RUN_SAVE_SPEC_CTRL: save guest SPEC_CTRL into vmx->spec_ctrl
  *
  * Returns:
  *	0 on VM-Exit, 1 on VM-Fail
@@ -115,24 +57,56 @@
 #endif
 	push %_ASM_BX
 
+	/* Save @vmx for SPEC_CTRL handling */
+	push %_ASM_ARG1
+
+	/* Save @flags for SPEC_CTRL handling */
+	push %_ASM_ARG3
+
 	/*
 	 * Save @regs, _ASM_ARG2 may be modified by vmx_update_host_rsp() and
 	 * @regs is needed after VM-Exit to save the guest's register values.
 	 */
 	push %_ASM_ARG2
 
-	/* Copy @launched to BL, _ASM_ARG3 is volatile. */
+	/* Copy @flags to BL, _ASM_ARG3 is volatile. */
 	mov %_ASM_ARG3B, %bl
 
-	/* Adjust RSP to account for the CALL to vmx_vmenter(). */
-	lea -WORD_SIZE(%_ASM_SP), %_ASM_ARG2
+	lea (%_ASM_SP), %_ASM_ARG2
 	call vmx_update_host_rsp
 
+	ALTERNATIVE "jmp .Lspec_ctrl_done", "", X86_FEATURE_MSR_SPEC_CTRL
+
+	/*
+	 * SPEC_CTRL handling: if the guest's SPEC_CTRL value differs from the
+	 * host's, write the MSR.
+	 *
+	 * IMPORTANT: To avoid RSB underflow attacks and any other nastiness,
+	 * there must not be any returns or indirect branches between this code
+	 * and vmentry.
+	 */
+	mov 2*WORD_SIZE(%_ASM_SP), %_ASM_DI
+	movl VMX_spec_ctrl(%_ASM_DI), %edi
+	movl PER_CPU_VAR(x86_spec_ctrl_current), %esi
+	cmp %edi, %esi
+	je .Lspec_ctrl_done
+	mov $MSR_IA32_SPEC_CTRL, %ecx
+	xor %edx, %edx
+	mov %edi, %eax
+	wrmsr
+
+.Lspec_ctrl_done:
+
+	/*
+	 * Since vmentry is serializing on affected CPUs, there's no need for
+	 * an LFENCE to stop speculation from skipping the wrmsr.
+	 */
+
 	/* Load @regs to RAX. */
 	mov (%_ASM_SP), %_ASM_AX
 
 	/* Check if vmlaunch or vmresume is needed */
-	testb %bl, %bl
+	bt   $VMX_RUN_VMRESUME_SHIFT, %bx
 
 	/* Load guest registers.  Don't clobber flags. */
 	mov VCPU_RCX(%_ASM_AX), %_ASM_CX
@@ -154,11 +128,39 @@
 	/* Load guest RAX.  This kills the @regs pointer! */
 	mov VCPU_RAX(%_ASM_AX), %_ASM_AX
 
-	/* Enter guest mode */
-	call vmx_vmenter
+	/* Clobbers EFLAGS.ZF */
+	CLEAR_CPU_BUFFERS
+
+	/* Check EFLAGS.CF from the VMX_RUN_VMRESUME bit test above. */
+	jnc .Lvmlaunch
+
+	/*
+	 * After a successful VMRESUME/VMLAUNCH, control flow "magically"
+	 * resumes below at 'vmx_vmexit' due to the VMCS HOST_RIP setting.
+	 * So this isn't a typical function and objtool needs to be told to
+	 * save the unwind state here and restore it below.
+	 */
+	UNWIND_HINT_SAVE
+
+/*
+ * If VMRESUME/VMLAUNCH and corresponding vmexit succeed, execution resumes at
+ * the 'vmx_vmexit' label below.
+ */
+.Lvmresume:
+	vmresume
+	jmp .Lvmfail
+
+.Lvmlaunch:
+	vmlaunch
+	jmp .Lvmfail
 
-	/* Jump on VM-Fail. */
-	jbe 2f
+	_ASM_EXTABLE(.Lvmresume, .Lfixup)
+	_ASM_EXTABLE(.Lvmlaunch, .Lfixup)
+
+SYM_INNER_LABEL(vmx_vmexit, SYM_L_GLOBAL)
+
+	/* Restore unwind state from before the VMRESUME/VMLAUNCH. */
+	UNWIND_HINT_RESTORE
 
 	/* Temporarily save guest's RAX. */
 	push %_ASM_AX
@@ -185,21 +187,23 @@
 	mov %r15, VCPU_R15(%_ASM_AX)
 #endif
 
-	/* Clear RAX to indicate VM-Exit (as opposed to VM-Fail). */
-	xor %eax, %eax
+	/* Clear return value to indicate VM-Exit (as opposed to VM-Fail). */
+	xor %ebx, %ebx
 
+.Lclear_regs:
 	/*
-	 * Clear all general purpose registers except RSP and RAX to prevent
+	 * Clear all general purpose registers except RSP and RBX to prevent
 	 * speculative use of the guest's values, even those that are reloaded
 	 * via the stack.  In theory, an L1 cache miss when restoring registers
 	 * could lead to speculative execution with the guest's values.
 	 * Zeroing XORs are dirt cheap, i.e. the extra paranoia is essentially
 	 * free.  RSP and RAX are exempt as RSP is restored by hardware during
-	 * VM-Exit and RAX is explicitly loaded with 0 or 1 to return VM-Fail.
+	 * VM-Exit and RBX is explicitly loaded with 0 or 1 to hold the return
+	 * value.
 	 */
-1:	xor %ecx, %ecx
+	xor %eax, %eax
+	xor %ecx, %ecx
 	xor %edx, %edx
-	xor %ebx, %ebx
 	xor %ebp, %ebp
 	xor %esi, %esi
 	xor %edi, %edi
@@ -216,8 +220,34 @@
 
 	/* "POP" @regs. */
 	add $WORD_SIZE, %_ASM_SP
-	pop %_ASM_BX
 
+	/*
+	 * IMPORTANT: RSB filling and SPEC_CTRL handling must be done before
+	 * the first unbalanced RET after vmexit!
+	 *
+	 * For retpoline or IBRS, RSB filling is needed to prevent poisoned RSB
+	 * entries and (in some cases) RSB underflow.
+	 *
+	 * eIBRS has its own protection against poisoned RSB, so it doesn't
+	 * need the RSB filling sequence.  But it does need to be enabled, and a
+	 * single call to retire, before the first unbalanced RET.
+         */
+
+	FILL_RETURN_BUFFER %_ASM_CX, RSB_CLEAR_LOOPS, X86_FEATURE_RSB_VMEXIT,\
+			   X86_FEATURE_RSB_VMEXIT_LITE
+
+
+	pop %_ASM_ARG2	/* @flags */
+	pop %_ASM_ARG1	/* @vmx */
+
+	call vmx_spec_ctrl_restore_host
+
+	CLEAR_BRANCH_HISTORY_VMEXIT
+
+	/* Put return value in AX */
+	mov %_ASM_BX, %_ASM_AX
+
+	pop %_ASM_BX
 #ifdef CONFIG_X86_64
 	pop %r12
 	pop %r13
@@ -228,11 +258,17 @@
 	pop %edi
 #endif
 	pop %_ASM_BP
-	ret
+	RET
+
+.Lfixup:
+	cmpb $0, kvm_rebooting
+	jne .Lvmfail
+	ud2
+.Lvmfail:
+	/* VM-Fail: set return value to 1 */
+	mov $1, %_ASM_BX
+	jmp .Lclear_regs
 
-	/* VM-Fail.  Out-of-line to avoid a taken Jcc after VM-Exit. */
-2:	mov $1, %eax
-	jmp 1b
 SYM_FUNC_END(__vmx_vcpu_run)
 
 
@@ -293,7 +329,7 @@
 	pop %_ASM_AX
 	pop %_ASM_BP
 
-	ret
+	RET
 SYM_FUNC_END(vmread_error_trampoline)
 
 SYM_FUNC_START(vmx_do_interrupt_nmi_irqoff)
@@ -326,5 +362,5 @@
 	 */
 	mov %_ASM_BP, %_ASM_SP
 	pop %_ASM_BP
-	ret
+	RET
 SYM_FUNC_END(vmx_do_interrupt_nmi_irqoff)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/vmx.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/vmx.c
@@ -35,7 +35,7 @@
 #include <asm/cpu_device_id.h>
 #include <asm/debugreg.h>
 #include <asm/desc.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/idtentry.h>
 #include <asm/io.h>
 #include <asm/irq_remapping.h>
@@ -200,9 +200,11 @@
 static unsigned int ple_window_max        = KVM_VMX_DEFAULT_PLE_WINDOW_MAX;
 module_param(ple_window_max, uint, 0444);
 
-/* Default is SYSTEM mode, 1 for host-guest mode */
+/* Default is SYSTEM mode, 1 for host-guest mode (which is BROKEN) */
 int __read_mostly pt_mode = PT_MODE_SYSTEM;
+#ifdef CONFIG_BROKEN
 module_param(pt_mode, int, S_IRUGO);
+#endif
 
 static DEFINE_STATIC_KEY_FALSE(vmx_l1d_should_flush);
 static DEFINE_STATIC_KEY_FALSE(vmx_l1d_flush_cond);
@@ -226,6 +228,9 @@
 #define L1D_CACHE_ORDER 4
 static void *vmx_l1d_flush_pages;
 
+/* Control for disabling CPU Fill buffer clear */
+static bool __read_mostly vmx_fb_clear_ctrl_available;
+
 static int vmx_setup_l1d_flush(enum vmx_l1d_flush_state l1tf)
 {
 	struct page *page;
@@ -357,6 +362,61 @@
 	return sprintf(s, "%s\n", vmentry_l1d_param[l1tf_vmx_mitigation].option);
 }
 
+static void vmx_setup_fb_clear_ctrl(void)
+{
+	u64 msr;
+
+	if (boot_cpu_has(X86_FEATURE_ARCH_CAPABILITIES) &&
+	    !boot_cpu_has_bug(X86_BUG_MDS) &&
+	    !boot_cpu_has_bug(X86_BUG_TAA)) {
+		rdmsrl(MSR_IA32_ARCH_CAPABILITIES, msr);
+		if (msr & ARCH_CAP_FB_CLEAR_CTRL)
+			vmx_fb_clear_ctrl_available = true;
+	}
+}
+
+static __always_inline void vmx_disable_fb_clear(struct vcpu_vmx *vmx)
+{
+	u64 msr;
+
+	if (!vmx->disable_fb_clear)
+		return;
+
+	msr = __rdmsr(MSR_IA32_MCU_OPT_CTRL);
+	msr |= FB_CLEAR_DIS;
+	native_wrmsrl(MSR_IA32_MCU_OPT_CTRL, msr);
+	/* Cache the MSR value to avoid reading it later */
+	vmx->msr_ia32_mcu_opt_ctrl = msr;
+}
+
+static __always_inline void vmx_enable_fb_clear(struct vcpu_vmx *vmx)
+{
+	if (!vmx->disable_fb_clear)
+		return;
+
+	vmx->msr_ia32_mcu_opt_ctrl &= ~FB_CLEAR_DIS;
+	native_wrmsrl(MSR_IA32_MCU_OPT_CTRL, vmx->msr_ia32_mcu_opt_ctrl);
+}
+
+static void vmx_update_fb_clear_dis(struct kvm_vcpu *vcpu, struct vcpu_vmx *vmx)
+{
+	vmx->disable_fb_clear = !cpu_feature_enabled(X86_FEATURE_CLEAR_CPU_BUF) &&
+		vmx_fb_clear_ctrl_available;
+
+	/*
+	 * If guest will not execute VERW, there is no need to set FB_CLEAR_DIS
+	 * at VMEntry. Skip the MSR read/write when a guest has no use case to
+	 * execute VERW.
+	 */
+	if ((vcpu->arch.arch_capabilities & ARCH_CAP_FB_CLEAR) ||
+	   ((vcpu->arch.arch_capabilities & ARCH_CAP_MDS_NO) &&
+	    (vcpu->arch.arch_capabilities & ARCH_CAP_TAA_NO) &&
+	    (vcpu->arch.arch_capabilities & ARCH_CAP_PSDP_NO) &&
+	    (vcpu->arch.arch_capabilities & ARCH_CAP_FBSDP_NO) &&
+	    (vcpu->arch.arch_capabilities & ARCH_CAP_SBDR_SSDP_NO)))
+		vmx->disable_fb_clear = false;
+}
+
 static const struct kernel_param_ops vmentry_l1d_flush_ops = {
 	.set = vmentry_l1d_flush_set,
 	.get = vmentry_l1d_flush_get,
@@ -769,24 +829,30 @@
 /*
  * Check if MSR is intercepted for currently loaded MSR bitmap.
  */
-static bool msr_write_intercepted(struct kvm_vcpu *vcpu, u32 msr)
+static bool msr_write_intercepted(struct vcpu_vmx *vmx, u32 msr)
 {
-	unsigned long *msr_bitmap;
-	int f = sizeof(unsigned long);
-
-	if (!cpu_has_vmx_msr_bitmap())
+	if (!(exec_controls_get(vmx) & CPU_BASED_USE_MSR_BITMAPS))
 		return true;
 
-	msr_bitmap = to_vmx(vcpu)->loaded_vmcs->msr_bitmap;
+	return vmx_test_msr_bitmap_write(vmx->loaded_vmcs->msr_bitmap, msr);
+}
 
-	if (msr <= 0x1fff) {
-		return !!test_bit(msr, msr_bitmap + 0x800 / f);
-	} else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff)) {
-		msr &= 0x1fff;
-		return !!test_bit(msr, msr_bitmap + 0xc00 / f);
-	}
+unsigned int __vmx_vcpu_run_flags(struct vcpu_vmx *vmx)
+{
+	unsigned int flags = 0;
 
-	return true;
+	if (vmx->loaded_vmcs->launched)
+		flags |= VMX_RUN_VMRESUME;
+
+	/*
+	 * If writes to the SPEC_CTRL MSR aren't intercepted, the guest is free
+	 * to change it directly without causing a vmexit.  In that case read
+	 * it after vmexit and store it in vmx->spec_ctrl.
+	 */
+	if (unlikely(!msr_write_intercepted(vmx, MSR_IA32_SPEC_CTRL)))
+		flags |= VMX_RUN_SAVE_SPEC_CTRL;
+
+	return flags;
 }
 
 static void clear_atomic_switch_msr_special(struct vcpu_vmx *vmx,
@@ -1269,8 +1335,10 @@
 
 		/*
 		 * No indirect branch prediction barrier needed when switching
-		 * the active VMCS within a guest, e.g. on nested VM-Enter.
-		 * The L1 VMM can protect itself with retpolines, IBPB or IBRS.
+		 * the active VMCS within a vCPU, unless IBRS is advertised to
+		 * the vCPU.  To minimize the number of IBPBs executed, KVM
+		 * performs IBPB on nested VM-Exit (a single nested transition
+		 * may switch the active VMCS multiple times).
 		 */
 		if (!buddy || WARN_ON_ONCE(buddy->vmcs != prev))
 			indirect_branch_prediction_barrier();
@@ -1351,6 +1419,11 @@
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
 	unsigned long old_rflags;
 
+	/*
+	 * Unlike CR0 and CR4, RFLAGS handling requires checking if the vCPU
+	 * is an unrestricted guest in order to mark L2 as needing emulation
+	 * if L1 runs L2 as a restricted guest.
+	 */
 	if (is_unrestricted_guest(vcpu)) {
 		kvm_register_mark_available(vcpu, VCPU_EXREG_RFLAGS);
 		vmx->rflags = rflags;
@@ -1370,6 +1443,11 @@
 		vmx->emulation_required = vmx_emulation_required(vcpu);
 }
 
+static bool vmx_get_if_flag(struct kvm_vcpu *vcpu)
+{
+	return vmx_get_rflags(vcpu) & X86_EFLAGS_IF;
+}
+
 u32 vmx_get_interrupt_shadow(struct kvm_vcpu *vcpu)
 {
 	u32 interruptibility = vmcs_read32(GUEST_INTERRUPTIBILITY_INFO);
@@ -1608,7 +1686,17 @@
 	kvm_deliver_exception_payload(vcpu);
 
 	if (has_error_code) {
-		vmcs_write32(VM_ENTRY_EXCEPTION_ERROR_CODE, error_code);
+		/*
+		 * Despite the error code being architecturally defined as 32
+		 * bits, and the VMCS field being 32 bits, Intel CPUs and thus
+		 * VMX don't actually supporting setting bits 31:16.  Hardware
+		 * will (should) never provide a bogus error code, but AMD CPUs
+		 * do generate error codes with bits 31:16 set, and so KVM's
+		 * ABI lets userspace shove in arbitrary 32-bit values.  Drop
+		 * the upper bits to avoid VM-Fail, losing information that
+		 * does't really exist is preferable to killing the VM.
+		 */
+		vmcs_write32(VM_ENTRY_EXCEPTION_ERROR_CODE, (u16)error_code);
 		intr_info |= INTR_INFO_DELIVER_CODE_MASK;
 	}
 
@@ -2234,6 +2322,10 @@
 			ret = kvm_set_msr_common(vcpu, msr_info);
 	}
 
+	/* FB_CLEAR may have changed, also update the FB_CLEAR_DIS behavior */
+	if (msr_index == MSR_IA32_ARCH_CAPABILITIES)
+		vmx_update_fb_clear_dis(vcpu, vmx);
+
 	return ret;
 }
 
@@ -2655,15 +2747,6 @@
 		if (!loaded_vmcs->msr_bitmap)
 			goto out_vmcs;
 		memset(loaded_vmcs->msr_bitmap, 0xff, PAGE_SIZE);
-
-		if (IS_ENABLED(CONFIG_HYPERV) &&
-		    static_branch_unlikely(&enable_evmcs) &&
-		    (ms_hyperv.nested_features & HV_X64_NESTED_MSR_BITMAP)) {
-			struct hv_enlightened_vmcs *evmcs =
-				(struct hv_enlightened_vmcs *)loaded_vmcs->vmcs;
-
-			evmcs->hv_enlightenments_control.msr_bitmap = 1;
-		}
 	}
 
 	memset(&loaded_vmcs->host_state, 0, sizeof(struct vmcs_host_state));
@@ -2814,6 +2897,15 @@
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
 	struct kvm_vmx *kvm_vmx = to_kvm_vmx(vcpu->kvm);
 
+	/*
+	 * KVM should never use VM86 to virtualize Real Mode when L2 is active,
+	 * as using VM86 is unnecessary if unrestricted guest is enabled, and
+	 * if unrestricted guest is disabled, VM-Enter (from L1) with CR0.PG=0
+	 * should VM-Fail and KVM should reject userspace attempts to stuff
+	 * CR0.PG=0 when L2 is active.
+	 */
+	WARN_ON_ONCE(is_guest_mode(vcpu));
+
 	vmx_get_segment(vcpu, &vmx->rmode.segs[VCPU_SREG_TR], VCPU_SREG_TR);
 	vmx_get_segment(vcpu, &vmx->rmode.segs[VCPU_SREG_ES], VCPU_SREG_ES);
 	vmx_get_segment(vcpu, &vmx->rmode.segs[VCPU_SREG_DS], VCPU_SREG_DS);
@@ -2927,6 +3019,13 @@
 	}
 }
 
+static inline int vmx_get_current_vpid(struct kvm_vcpu *vcpu)
+{
+	if (is_guest_mode(vcpu) && nested_cpu_has_vpid(get_vmcs12(vcpu)))
+		return nested_get_vpid02(vcpu);
+	return to_vmx(vcpu)->vpid;
+}
+
 static void vmx_flush_tlb_current(struct kvm_vcpu *vcpu)
 {
 	struct kvm_mmu *mmu = vcpu->arch.mmu;
@@ -2939,31 +3038,29 @@
 	if (enable_ept)
 		ept_sync_context(construct_eptp(vcpu, root_hpa,
 						mmu->shadow_root_level));
-	else if (!is_guest_mode(vcpu))
-		vpid_sync_context(to_vmx(vcpu)->vpid);
 	else
-		vpid_sync_context(nested_get_vpid02(vcpu));
+		vpid_sync_context(vmx_get_current_vpid(vcpu));
 }
 
 static void vmx_flush_tlb_gva(struct kvm_vcpu *vcpu, gva_t addr)
 {
 	/*
-	 * vpid_sync_vcpu_addr() is a nop if vmx->vpid==0, see the comment in
+	 * vpid_sync_vcpu_addr() is a nop if vpid==0, see the comment in
 	 * vmx_flush_tlb_guest() for an explanation of why this is ok.
 	 */
-	vpid_sync_vcpu_addr(to_vmx(vcpu)->vpid, addr);
+	vpid_sync_vcpu_addr(vmx_get_current_vpid(vcpu), addr);
 }
 
 static void vmx_flush_tlb_guest(struct kvm_vcpu *vcpu)
 {
 	/*
-	 * vpid_sync_context() is a nop if vmx->vpid==0, e.g. if enable_vpid==0
-	 * or a vpid couldn't be allocated for this vCPU.  VM-Enter and VM-Exit
-	 * are required to flush GVA->{G,H}PA mappings from the TLB if vpid is
+	 * vpid_sync_context() is a nop if vpid==0, e.g. if enable_vpid==0 or a
+	 * vpid couldn't be allocated for this vCPU.  VM-Enter and VM-Exit are
+	 * required to flush GVA->{G,H}PA mappings from the TLB if vpid is
 	 * disabled (VM-Enter with vpid enabled and vpid==0 is disallowed),
 	 * i.e. no explicit INVVPID is necessary.
 	 */
-	vpid_sync_context(to_vmx(vcpu)->vpid);
+	vpid_sync_context(vmx_get_current_vpid(vcpu));
 }
 
 void vmx_ept_load_pdptrs(struct kvm_vcpu *vcpu)
@@ -2999,6 +3096,17 @@
 #define CR3_EXITING_BITS (CPU_BASED_CR3_LOAD_EXITING | \
 			  CPU_BASED_CR3_STORE_EXITING)
 
+static bool vmx_is_valid_cr0(struct kvm_vcpu *vcpu, unsigned long cr0)
+{
+	if (is_guest_mode(vcpu))
+		return nested_guest_cr0_valid(vcpu, cr0);
+
+	if (to_vmx(vcpu)->nested.vmxon)
+		return nested_host_cr0_valid(vcpu, cr0);
+
+	return true;
+}
+
 void vmx_set_cr0(struct kvm_vcpu *vcpu, unsigned long cr0)
 {
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
@@ -3008,7 +3116,7 @@
 	old_cr0_pg = kvm_read_cr0_bits(vcpu, X86_CR0_PG);
 
 	hw_cr0 = (cr0 & ~KVM_VM_CR0_ALWAYS_OFF);
-	if (is_unrestricted_guest(vcpu))
+	if (enable_unrestricted_guest)
 		hw_cr0 |= KVM_VM_CR0_ALWAYS_ON_UNRESTRICTED_GUEST;
 	else {
 		hw_cr0 |= KVM_VM_CR0_ALWAYS_ON;
@@ -3036,7 +3144,7 @@
 	}
 #endif
 
-	if (enable_ept && !is_unrestricted_guest(vcpu)) {
+	if (enable_ept && !enable_unrestricted_guest) {
 		/*
 		 * Ensure KVM has an up-to-date snapshot of the guest's CR3.  If
 		 * the below code _enables_ CR3 exiting, vmx_cache_reg() will
@@ -3135,8 +3243,8 @@
 {
 	/*
 	 * We operate under the default treatment of SMM, so VMX cannot be
-	 * enabled under SMM.  Note, whether or not VMXE is allowed at all is
-	 * handled by kvm_is_valid_cr4().
+	 * enabled under SMM.  Note, whether or not VMXE is allowed at all,
+	 * i.e. is a reserved bit, is handled by common x86 code.
 	 */
 	if ((cr4 & X86_CR4_VMXE) && is_smm(vcpu))
 		return false;
@@ -3159,7 +3267,7 @@
 	unsigned long hw_cr4;
 
 	hw_cr4 = (cr4_read_shadow() & X86_CR4_MCE) | (cr4 & ~X86_CR4_MCE);
-	if (is_unrestricted_guest(vcpu))
+	if (enable_unrestricted_guest)
 		hw_cr4 |= KVM_VM_CR4_ALWAYS_ON_UNRESTRICTED_GUEST;
 	else if (vmx->rmode.vm86_active)
 		hw_cr4 |= KVM_RMODE_VM_CR4_ALWAYS_ON;
@@ -3179,7 +3287,7 @@
 	vcpu->arch.cr4 = cr4;
 	kvm_register_mark_available(vcpu, VCPU_EXREG_CR4);
 
-	if (!is_unrestricted_guest(vcpu)) {
+	if (!enable_unrestricted_guest) {
 		if (enable_ept) {
 			if (!is_paging(vcpu)) {
 				hw_cr4 &= ~X86_CR4_PAE;
@@ -3274,18 +3382,15 @@
 {
 	u32 ar;
 
-	if (var->unusable || !var->present)
-		ar = 1 << 16;
-	else {
-		ar = var->type & 15;
-		ar |= (var->s & 1) << 4;
-		ar |= (var->dpl & 3) << 5;
-		ar |= (var->present & 1) << 7;
-		ar |= (var->avl & 1) << 12;
-		ar |= (var->l & 1) << 13;
-		ar |= (var->db & 1) << 14;
-		ar |= (var->g & 1) << 15;
-	}
+	ar = var->type & 15;
+	ar |= (var->s & 1) << 4;
+	ar |= (var->dpl & 3) << 5;
+	ar |= (var->present & 1) << 7;
+	ar |= (var->avl & 1) << 12;
+	ar |= (var->l & 1) << 13;
+	ar |= (var->db & 1) << 14;
+	ar |= (var->g & 1) << 15;
+	ar |= (var->unusable || !var->present) << 16;
 
 	return ar;
 }
@@ -3695,44 +3800,20 @@
 	spin_unlock(&vmx_vpid_lock);
 }
 
-static void vmx_clear_msr_bitmap_read(ulong *msr_bitmap, u32 msr)
-{
-	int f = sizeof(unsigned long);
-
-	if (msr <= 0x1fff)
-		__clear_bit(msr, msr_bitmap + 0x000 / f);
-	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
-		__clear_bit(msr & 0x1fff, msr_bitmap + 0x400 / f);
-}
-
-static void vmx_clear_msr_bitmap_write(ulong *msr_bitmap, u32 msr)
+static void vmx_msr_bitmap_l01_changed(struct vcpu_vmx *vmx)
 {
-	int f = sizeof(unsigned long);
-
-	if (msr <= 0x1fff)
-		__clear_bit(msr, msr_bitmap + 0x800 / f);
-	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
-		__clear_bit(msr & 0x1fff, msr_bitmap + 0xc00 / f);
-}
-
-static void vmx_set_msr_bitmap_read(ulong *msr_bitmap, u32 msr)
-{
-	int f = sizeof(unsigned long);
-
-	if (msr <= 0x1fff)
-		__set_bit(msr, msr_bitmap + 0x000 / f);
-	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
-		__set_bit(msr & 0x1fff, msr_bitmap + 0x400 / f);
-}
-
-static void vmx_set_msr_bitmap_write(ulong *msr_bitmap, u32 msr)
-{
-	int f = sizeof(unsigned long);
+	/*
+	 * When KVM is a nested hypervisor on top of Hyper-V and uses
+	 * 'Enlightened MSR Bitmap' feature L0 needs to know that MSR
+	 * bitmap has changed.
+	 */
+	if (IS_ENABLED(CONFIG_HYPERV) && static_branch_unlikely(&enable_evmcs)) {
+		struct hv_enlightened_vmcs *evmcs = (void *)vmx->vmcs01.vmcs;
 
-	if (msr <= 0x1fff)
-		__set_bit(msr, msr_bitmap + 0x800 / f);
-	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
-		__set_bit(msr & 0x1fff, msr_bitmap + 0xc00 / f);
+		if (evmcs->hv_enlightenments_control.msr_bitmap)
+			evmcs->hv_clean_fields &=
+				~HV_VMX_ENLIGHTENED_CLEAN_FIELD_MSR_BITMAP;
+	}
 }
 
 void vmx_disable_intercept_for_msr(struct kvm_vcpu *vcpu, u32 msr, int type)
@@ -3743,8 +3824,7 @@
 	if (!cpu_has_vmx_msr_bitmap())
 		return;
 
-	if (static_branch_unlikely(&enable_evmcs))
-		evmcs_touch_msr_bitmap();
+	vmx_msr_bitmap_l01_changed(vmx);
 
 	/*
 	 * Mark the desired intercept state in shadow bitmap, this is needed
@@ -3788,8 +3868,7 @@
 	if (!cpu_has_vmx_msr_bitmap())
 		return;
 
-	if (static_branch_unlikely(&enable_evmcs))
-		evmcs_touch_msr_bitmap();
+	vmx_msr_bitmap_l01_changed(vmx);
 
 	/*
 	 * Mark the desired intercept state in shadow bitmap, this is needed
@@ -4012,8 +4091,7 @@
 	if (pi_test_and_set_on(&vmx->pi_desc))
 		return 0;
 
-	if (vcpu != kvm_get_running_vcpu() &&
-	    !kvm_vcpu_trigger_posted_interrupt(vcpu, false))
+	if (!kvm_vcpu_trigger_posted_interrupt(vcpu, false))
 		kvm_vcpu_kick(vcpu);
 
 	return 0;
@@ -4140,6 +4218,11 @@
 {
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
 
+	if (is_guest_mode(vcpu)) {
+		vmx->nested.update_vmcs01_apicv_status = true;
+		return;
+	}
+
 	pin_controls_set(vmx, vmx_pin_based_exec_ctrl(vmx));
 	if (cpu_has_secondary_exec_ctrls()) {
 		if (kvm_vcpu_apicv_active(vcpu))
@@ -4487,6 +4570,8 @@
 	kvm_make_request(KVM_REQ_APIC_PAGE_RELOAD, vcpu);
 
 	vpid_sync_context(vmx->vpid);
+
+	vmx_update_fb_clear_dis(vcpu, vmx);
 }
 
 static void vmx_enable_irq_window(struct kvm_vcpu *vcpu)
@@ -4623,14 +4708,19 @@
 	return !vmx_nmi_blocked(vcpu);
 }
 
+bool __vmx_interrupt_blocked(struct kvm_vcpu *vcpu)
+{
+	return !(vmx_get_rflags(vcpu) & X86_EFLAGS_IF) ||
+	       (vmcs_read32(GUEST_INTERRUPTIBILITY_INFO) &
+		(GUEST_INTR_STATE_STI | GUEST_INTR_STATE_MOV_SS));
+}
+
 bool vmx_interrupt_blocked(struct kvm_vcpu *vcpu)
 {
 	if (is_guest_mode(vcpu) && nested_exit_on_intr(vcpu))
 		return false;
 
-	return !(vmx_get_rflags(vcpu) & X86_EFLAGS_IF) ||
-	       (vmcs_read32(GUEST_INTERRUPTIBILITY_INFO) &
-		(GUEST_INTR_STATE_STI | GUEST_INTR_STATE_MOV_SS));
+	return __vmx_interrupt_blocked(vcpu);
 }
 
 static int vmx_interrupt_allowed(struct kvm_vcpu *vcpu, bool for_injection)
@@ -4833,8 +4923,33 @@
 		dr6 = vmx_get_exit_qual(vcpu);
 		if (!(vcpu->guest_debug &
 		      (KVM_GUESTDBG_SINGLESTEP | KVM_GUESTDBG_USE_HW_BP))) {
+			/*
+			 * If the #DB was due to ICEBP, a.k.a. INT1, skip the
+			 * instruction.  ICEBP generates a trap-like #DB, but
+			 * despite its interception control being tied to #DB,
+			 * is an instruction intercept, i.e. the VM-Exit occurs
+			 * on the ICEBP itself.  Note, skipping ICEBP also
+			 * clears STI and MOVSS blocking.
+			 *
+			 * For all other #DBs, set vmcs.PENDING_DBG_EXCEPTIONS.BS
+			 * if single-step is enabled in RFLAGS and STI or MOVSS
+			 * blocking is active, as the CPU doesn't set the bit
+			 * on VM-Exit due to #DB interception.  VM-Entry has a
+			 * consistency check that a single-step #DB is pending
+			 * in this scenario as the previous instruction cannot
+			 * have toggled RFLAGS.TF 0=>1 (because STI and POP/MOV
+			 * don't modify RFLAGS), therefore the one instruction
+			 * delay when activating single-step breakpoints must
+			 * have already expired.  Note, the CPU sets/clears BS
+			 * as appropriate for all other VM-Exits types.
+			 */
 			if (is_icebp(intr_info))
 				WARN_ON(!skip_emulated_instruction(vcpu));
+			else if ((vmx_get_rflags(vcpu) & X86_EFLAGS_TF) &&
+				 (vmcs_read32(GUEST_INTERRUPTIBILITY_INFO) &
+				  (GUEST_INTR_STATE_STI | GUEST_INTR_STATE_MOV_SS)))
+				vmcs_writel(GUEST_PENDING_DBG_EXCEPTIONS,
+					    vmcs_readl(GUEST_PENDING_DBG_EXCEPTIONS) | DR6_BS);
 
 			kvm_queue_exception_p(vcpu, DB_VECTOR, dr6);
 			return 1;
@@ -4940,18 +5055,11 @@
 		val = (val & ~vmcs12->cr0_guest_host_mask) |
 			(vmcs12->guest_cr0 & vmcs12->cr0_guest_host_mask);
 
-		if (!nested_guest_cr0_valid(vcpu, val))
-			return 1;
-
 		if (kvm_set_cr0(vcpu, val))
 			return 1;
 		vmcs_writel(CR0_READ_SHADOW, orig_val);
 		return 0;
 	} else {
-		if (to_vmx(vcpu)->nested.vmxon &&
-		    !nested_host_cr0_valid(vcpu, val))
-			return 1;
-
 		return kvm_set_cr0(vcpu, val);
 	}
 }
@@ -5907,18 +6015,14 @@
 		vmx_flush_pml_buffer(vcpu);
 
 	/*
-	 * We should never reach this point with a pending nested VM-Enter, and
-	 * more specifically emulation of L2 due to invalid guest state (see
-	 * below) should never happen as that means we incorrectly allowed a
-	 * nested VM-Enter with an invalid vmcs12.
+	 * KVM should never reach this point with a pending nested VM-Enter.
+	 * More specifically, short-circuiting VM-Entry to emulate L2 due to
+	 * invalid guest state should never happen as that means KVM knowingly
+	 * allowed a nested VM-Enter with an invalid vmcs12.  More below.
 	 */
 	if (KVM_BUG_ON(vmx->nested.nested_run_pending, vcpu->kvm))
 		return -EIO;
 
-	/* If guest state is invalid, start emulating */
-	if (vmx->emulation_required)
-		return handle_invalid_guest_state(vcpu);
-
 	if (is_guest_mode(vcpu)) {
 		/*
 		 * PML is never enabled when running L2, bail immediately if a
@@ -5940,10 +6044,30 @@
 		 */
 		nested_mark_vmcs12_pages_dirty(vcpu);
 
+		/*
+		 * Synthesize a triple fault if L2 state is invalid.  In normal
+		 * operation, nested VM-Enter rejects any attempt to enter L2
+		 * with invalid state.  However, those checks are skipped if
+		 * state is being stuffed via RSM or KVM_SET_NESTED_STATE.  If
+		 * L2 state is invalid, it means either L1 modified SMRAM state
+		 * or userspace provided bad state.  Synthesize TRIPLE_FAULT as
+		 * doing so is architecturally allowed in the RSM case, and is
+		 * the least awful solution for the userspace case without
+		 * risking false positives.
+		 */
+		if (vmx->emulation_required) {
+			nested_vmx_vmexit(vcpu, EXIT_REASON_TRIPLE_FAULT, 0, 0);
+			return 1;
+		}
+
 		if (nested_vmx_reflect_vmexit(vcpu))
 			return 1;
 	}
 
+	/* If guest state is invalid, start emulating.  L2 is handled above. */
+	if (vmx->emulation_required)
+		return handle_invalid_guest_state(vcpu);
+
 	if (exit_reason.failed_vmentry) {
 		dump_vmcs(vcpu);
 		vcpu->run->exit_reason = KVM_EXIT_FAIL_ENTRY;
@@ -6288,9 +6412,9 @@
 {
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
 	int max_irr;
-	bool max_irr_updated;
+	bool got_posted_interrupt;
 
-	if (KVM_BUG_ON(!vcpu->arch.apicv_active, vcpu->kvm))
+	if (KVM_BUG_ON(!enable_apicv, vcpu->kvm))
 		return -EIO;
 
 	if (pi_test_on(&vmx->pi_desc)) {
@@ -6300,22 +6424,33 @@
 		 * But on x86 this is just a compiler barrier anyway.
 		 */
 		smp_mb__after_atomic();
-		max_irr_updated =
+		got_posted_interrupt =
 			kvm_apic_update_irr(vcpu, vmx->pi_desc.pir, &max_irr);
-
-		/*
-		 * If we are running L2 and L1 has a new pending interrupt
-		 * which can be injected, this may cause a vmexit or it may
-		 * be injected into L2.  Either way, this interrupt will be
-		 * processed via KVM_REQ_EVENT, not RVI, because we do not use
-		 * virtual interrupt delivery to inject L1 interrupts into L2.
-		 */
-		if (is_guest_mode(vcpu) && max_irr_updated)
-			kvm_make_request(KVM_REQ_EVENT, vcpu);
 	} else {
 		max_irr = kvm_lapic_find_highest_irr(vcpu);
+		got_posted_interrupt = false;
 	}
-	vmx_hwapic_irr_update(vcpu, max_irr);
+
+	/*
+	 * Newly recognized interrupts are injected via either virtual interrupt
+	 * delivery (RVI) or KVM_REQ_EVENT.  Virtual interrupt delivery is
+	 * disabled in two cases:
+	 *
+	 * 1) If L2 is running and the vCPU has a new pending interrupt.  If L1
+	 * wants to exit on interrupts, KVM_REQ_EVENT is needed to synthesize a
+	 * VM-Exit to L1.  If L1 doesn't want to exit, the interrupt is injected
+	 * into L2, but KVM doesn't use virtual interrupt delivery to inject
+	 * interrupts into L2, and so KVM_REQ_EVENT is again needed.
+	 *
+	 * 2) If APICv is disabled for this vCPU, assigned devices may still
+	 * attempt to post interrupts.  The posted interrupt vector will cause
+	 * a VM-Exit and the subsequent entry will call sync_pir_to_irr.
+	 */
+	if (!is_guest_mode(vcpu) && kvm_vcpu_apicv_active(vcpu))
+		vmx_set_rvi(max_irr);
+	else if (got_posted_interrupt)
+		kvm_make_request(KVM_REQ_EVENT, vcpu);
+
 	return max_irr;
 }
 
@@ -6375,6 +6510,7 @@
 		return;
 
 	handle_interrupt_nmi_irqoff(vcpu, gate_offset(desc));
+	vcpu->arch.at_instruction_boundary = true;
 }
 
 static void vmx_handle_exit_irqoff(struct kvm_vcpu *vcpu)
@@ -6576,6 +6712,31 @@
 	}
 }
 
+void noinstr vmx_spec_ctrl_restore_host(struct vcpu_vmx *vmx,
+					unsigned int flags)
+{
+	u64 hostval = this_cpu_read(x86_spec_ctrl_current);
+
+	if (!cpu_feature_enabled(X86_FEATURE_MSR_SPEC_CTRL))
+		return;
+
+	if (flags & VMX_RUN_SAVE_SPEC_CTRL)
+		vmx->spec_ctrl = __rdmsr(MSR_IA32_SPEC_CTRL);
+
+	/*
+	 * If the guest/host SPEC_CTRL values differ, restore the host value.
+	 *
+	 * For legacy IBRS, the IBRS bit always needs to be written after
+	 * transitioning from a less privileged predictor mode, regardless of
+	 * whether the guest/host values differ.
+	 */
+	if (cpu_feature_enabled(X86_FEATURE_KERNEL_IBRS) ||
+	    vmx->spec_ctrl != hostval)
+		native_wrmsrl(MSR_IA32_SPEC_CTRL, hostval);
+
+	barrier_nospec();
+}
+
 static fastpath_t vmx_exit_handlers_fastpath(struct kvm_vcpu *vcpu)
 {
 	switch (to_vmx(vcpu)->exit_reason.basic) {
@@ -6589,24 +6750,35 @@
 }
 
 static noinstr void vmx_vcpu_enter_exit(struct kvm_vcpu *vcpu,
-					struct vcpu_vmx *vmx)
+					struct vcpu_vmx *vmx,
+					unsigned long flags)
 {
 	kvm_guest_enter_irqoff();
 
-	/* L1D Flush includes CPU buffer clear to mitigate MDS */
+	/*
+	 * L1D Flush includes CPU buffer clear to mitigate MDS, but VERW
+	 * mitigation for MDS is done late in VMentry and is still
+	 * executed in spite of L1D Flush. This is because an extra VERW
+	 * should not matter much after the big hammer L1D Flush.
+	 */
 	if (static_branch_unlikely(&vmx_l1d_should_flush))
 		vmx_l1d_flush(vcpu);
-	else if (static_branch_unlikely(&mds_user_clear))
+	else if (static_branch_unlikely(&mmio_stale_data_clear) &&
+		 kvm_arch_has_assigned_device(vcpu->kvm))
 		mds_clear_cpu_buffers();
 
+	vmx_disable_fb_clear(vmx);
+
 	if (vcpu->arch.cr2 != native_read_cr2())
 		native_write_cr2(vcpu->arch.cr2);
 
 	vmx->fail = __vmx_vcpu_run(vmx, (unsigned long *)&vcpu->arch.regs,
-				   vmx->loaded_vmcs->launched);
+				   flags);
 
 	vcpu->arch.cr2 = native_read_cr2();
 
+	vmx_enable_fb_clear(vmx);
+
 	kvm_guest_exit_irqoff();
 }
 
@@ -6626,9 +6798,7 @@
 	 * consistency check VM-Exit due to invalid guest state and bail.
 	 */
 	if (unlikely(vmx->emulation_required)) {
-
-		/* We don't emulate invalid state of a nested guest */
-		vmx->fail = is_guest_mode(vcpu);
+		vmx->fail = 0;
 
 		vmx->exit_reason.full = EXIT_REASON_INVALID_STATE;
 		vmx->exit_reason.failed_vmentry = 1;
@@ -6694,36 +6864,8 @@
 
 	kvm_wait_lapic_expire(vcpu);
 
-	/*
-	 * If this vCPU has touched SPEC_CTRL, restore the guest's value if
-	 * it's non-zero. Since vmentry is serialising on affected CPUs, there
-	 * is no need to worry about the conditional branch over the wrmsr
-	 * being speculatively taken.
-	 */
-	x86_spec_ctrl_set_guest(vmx->spec_ctrl, 0);
-
 	/* The actual VMENTER/EXIT is in the .noinstr.text section. */
-	vmx_vcpu_enter_exit(vcpu, vmx);
-
-	/*
-	 * We do not use IBRS in the kernel. If this vCPU has used the
-	 * SPEC_CTRL MSR it may have left it on; save the value and
-	 * turn it off. This is much more efficient than blindly adding
-	 * it to the atomic save/restore list. Especially as the former
-	 * (Saving guest MSRs on vmexit) doesn't even exist in KVM.
-	 *
-	 * For non-nested case:
-	 * If the L01 MSR bitmap does not intercept the MSR, then we need to
-	 * save it.
-	 *
-	 * For nested case:
-	 * If the L02 MSR bitmap does not intercept the MSR, then we need to
-	 * save it.
-	 */
-	if (unlikely(!msr_write_intercepted(vcpu, MSR_IA32_SPEC_CTRL)))
-		vmx->spec_ctrl = native_read_msr(MSR_IA32_SPEC_CTRL);
-
-	x86_spec_ctrl_restore_host(vmx->spec_ctrl, 0);
+	vmx_vcpu_enter_exit(vcpu, vmx, __vmx_vcpu_run_flags(vmx));
 
 	/* All fields are clean at this point */
 	if (static_branch_unlikely(&enable_evmcs)) {
@@ -6853,6 +6995,19 @@
 	if (err < 0)
 		goto free_pml;
 
+	/*
+	 * Use Hyper-V 'Enlightened MSR Bitmap' feature when KVM runs as a
+	 * nested (L1) hypervisor and Hyper-V in L0 supports it. Enable the
+	 * feature only for vmcs01, KVM currently isn't equipped to realize any
+	 * performance benefits from enabling it for vmcs02.
+	 */
+	if (IS_ENABLED(CONFIG_HYPERV) && static_branch_unlikely(&enable_evmcs) &&
+	    (ms_hyperv.nested_features & HV_X64_NESTED_MSR_BITMAP)) {
+		struct hv_enlightened_vmcs *evmcs = (void *)vmx->vmcs01.vmcs;
+
+		evmcs->hv_enlightenments_control.msr_bitmap = 1;
+	}
+
 	/* The MSR bitmap starts with all ones */
 	bitmap_fill(vmx->shadow_msr_intercept.read, MAX_POSSIBLE_PASSTHROUGH_MSRS);
 	bitmap_fill(vmx->shadow_msr_intercept.write, MAX_POSSIBLE_PASSTHROUGH_MSRS);
@@ -7359,6 +7514,21 @@
 		/* FIXME: produce nested vmexit and return X86EMUL_INTERCEPTED.  */
 		break;
 
+	case x86_intercept_pause:
+		/*
+		 * PAUSE is a single-byte NOP with a REPE prefix, i.e. collides
+		 * with vanilla NOPs in the emulator.  Apply the interception
+		 * check only to actual PAUSE instructions.  Don't check
+		 * PAUSE-loop-exiting, software can't expect a given PAUSE to
+		 * exit, i.e. KVM is within its rights to allow L2 to execute
+		 * the PAUSE.
+		 */
+		if ((info->rep_prefix != REPE_PREFIX) ||
+		    !nested_cpu_has2(vmcs12, CPU_BASED_PAUSE_EXITING))
+			return X86EMUL_CONTINUE;
+
+		break;
+
 	/* TODO: check more intercepts... */
 	default:
 		break;
@@ -7463,17 +7633,11 @@
 	if (pi_pre_block(vcpu))
 		return 1;
 
-	if (kvm_lapic_hv_timer_in_use(vcpu))
-		kvm_lapic_switch_to_sw_timer(vcpu);
-
 	return 0;
 }
 
 static void vmx_post_block(struct kvm_vcpu *vcpu)
 {
-	if (kvm_x86_ops.set_hv_timer)
-		kvm_lapic_switch_to_hv_timer(vcpu);
-
 	pi_post_block(vcpu);
 }
 
@@ -7524,6 +7688,7 @@
 		if (ret)
 			return ret;
 
+		vmx->nested.nested_run_pending = 1;
 		vmx->nested.smm.guest_mode = false;
 	}
 	return 0;
@@ -7551,6 +7716,8 @@
 
 static void hardware_unsetup(void)
 {
+	kvm_set_posted_intr_wakeup_handler(NULL);
+
 	if (nested)
 		nested_vmx_hardware_unsetup();
 
@@ -7593,6 +7760,7 @@
 	.set_segment = vmx_set_segment,
 	.get_cpl = vmx_get_cpl,
 	.get_cs_db_l_bits = vmx_get_cs_db_l_bits,
+	.is_valid_cr0 = vmx_is_valid_cr0,
 	.set_cr0 = vmx_set_cr0,
 	.is_valid_cr4 = vmx_is_valid_cr4,
 	.set_cr4 = vmx_set_cr4,
@@ -7606,6 +7774,7 @@
 	.cache_reg = vmx_cache_reg,
 	.get_rflags = vmx_get_rflags,
 	.set_rflags = vmx_set_rflags,
+	.get_if_flag = vmx_get_if_flag,
 
 	.tlb_flush_all = vmx_flush_tlb_all,
 	.tlb_flush_current = vmx_flush_tlb_current,
@@ -7781,6 +7950,11 @@
 	if (!cpu_has_virtual_nmis())
 		enable_vnmi = 0;
 
+#ifdef CONFIG_X86_SGX_KVM
+	if (!cpu_has_vmx_encls_vmexit())
+		enable_sgx = false;
+#endif
+
 	/*
 	 * set_apic_access_page_addr() is used to reload apic access
 	 * page upon invalidation.  No need to do anything if not
@@ -7809,10 +7983,10 @@
 		ple_window_shrink = 0;
 	}
 
-	if (!cpu_has_vmx_apicv()) {
+	if (!cpu_has_vmx_apicv())
 		enable_apicv = 0;
+	if (!enable_apicv)
 		vmx_x86_ops.sync_pir_to_irr = NULL;
-	}
 
 	if (cpu_has_vmx_tsc_scaling()) {
 		kvm_has_tsc_control = true;
@@ -7879,8 +8053,6 @@
 		vmx_x86_ops.request_immediate_exit = __kvm_request_immediate_exit;
 	}
 
-	kvm_set_posted_intr_wakeup_handler(pi_wakeup_handler);
-
 	kvm_mce_cap_supported |= MCG_LMCE_P;
 
 	if (pt_mode != PT_MODE_SYSTEM && pt_mode != PT_MODE_HOST_GUEST)
@@ -7904,6 +8076,9 @@
 	r = alloc_kvm_area();
 	if (r)
 		nested_vmx_hardware_unsetup();
+
+	kvm_set_posted_intr_wakeup_handler(pi_wakeup_handler);
+
 	return r;
 }
 
@@ -7912,6 +8087,7 @@
 	.disabled_by_bios = vmx_disabled_by_bios,
 	.check_processor_compatibility = vmx_check_processor_compat,
 	.hardware_setup = hardware_setup,
+	.intel_pt_intr_in_guest = vmx_pt_mode_is_host_guest,
 
 	.runtime_ops = &vmx_x86_ops,
 };
@@ -8020,6 +8196,8 @@
 		return r;
 	}
 
+	vmx_setup_fb_clear_ctrl();
+
 	for_each_possible_cpu(cpu) {
 		INIT_LIST_HEAD(&per_cpu(loaded_vmcss_on_cpu, cpu));
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/vmx.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/vmx.h
@@ -8,11 +8,12 @@
 #include <asm/intel_pt.h>
 
 #include "capabilities.h"
-#include "kvm_cache_regs.h"
+#include "../kvm_cache_regs.h"
 #include "posted_intr.h"
 #include "vmcs.h"
 #include "vmx_ops.h"
-#include "cpuid.h"
+#include "../cpuid.h"
+#include "run_flags.h"
 
 #define MSR_TYPE_R	1
 #define MSR_TYPE_W	2
@@ -91,6 +92,18 @@
 	u32 full;
 };
 
+static inline bool intel_pmu_has_perf_global_ctrl(struct kvm_pmu *pmu)
+{
+	/*
+	 * Architecturally, Intel's SDM states that IA32_PERF_GLOBAL_CTRL is
+	 * supported if "CPUID.0AH: EAX[7:0] > 0", i.e. if the PMU version is
+	 * greater than zero.  However, KVM only exposes and emulates the MSR
+	 * to/for the guest if the guest PMU supports at least "Architectural
+	 * Performance Monitoring Version 2".
+	 */
+	return pmu->version > 1;
+}
+
 #define vcpu_to_lbr_desc(vcpu) (&to_vmx(vcpu)->lbr_desc)
 #define vcpu_to_lbr_records(vcpu) (&to_vmx(vcpu)->lbr_desc.records)
 
@@ -164,6 +177,7 @@
 	bool change_vmcs01_virtual_apic_mode;
 	bool reload_vmcs01_apic_access_page;
 	bool update_vmcs01_cpu_dirty_logging;
+	bool update_vmcs01_apicv_status;
 
 	/*
 	 * Enlightened VMCS has been enabled. It does not mean that L1 has to
@@ -325,6 +339,8 @@
 	u64 msr_ia32_feature_control_valid_bits;
 	/* SGX Launch Control public key hash */
 	u64 msr_ia32_sgxlepubkeyhash[4];
+	u64 msr_ia32_mcu_opt_ctrl;
+	bool disable_fb_clear;
 
 	struct pt_desc pt_desc;
 	struct lbr_desc lbr_desc;
@@ -372,6 +388,7 @@
 bool vmx_guest_inject_ac(struct kvm_vcpu *vcpu);
 void vmx_update_exception_bitmap(struct kvm_vcpu *vcpu);
 bool vmx_nmi_blocked(struct kvm_vcpu *vcpu);
+bool __vmx_interrupt_blocked(struct kvm_vcpu *vcpu);
 bool vmx_interrupt_blocked(struct kvm_vcpu *vcpu);
 bool vmx_get_nmi_mask(struct kvm_vcpu *vcpu);
 void vmx_set_nmi_mask(struct kvm_vcpu *vcpu, bool masked);
@@ -379,7 +396,10 @@
 struct vmx_uret_msr *vmx_find_uret_msr(struct vcpu_vmx *vmx, u32 msr);
 void pt_update_intercept_for_msr(struct kvm_vcpu *vcpu);
 void vmx_update_host_rsp(struct vcpu_vmx *vmx, unsigned long host_rsp);
-bool __vmx_vcpu_run(struct vcpu_vmx *vmx, unsigned long *regs, bool launched);
+void vmx_spec_ctrl_restore_host(struct vcpu_vmx *vmx, unsigned int flags);
+unsigned int __vmx_vcpu_run_flags(struct vcpu_vmx *vmx);
+bool __vmx_vcpu_run(struct vcpu_vmx *vmx, unsigned long *regs,
+		    unsigned int flags);
 int vmx_find_loadstore_msr_slot(struct vmx_msrs *m, u32 msr);
 void vmx_ept_load_pdptrs(struct kvm_vcpu *vcpu);
 
@@ -400,6 +420,69 @@
 
 void vmx_update_cpu_dirty_logging(struct kvm_vcpu *vcpu);
 
+static inline bool vmx_test_msr_bitmap_read(ulong *msr_bitmap, u32 msr)
+{
+	int f = sizeof(unsigned long);
+
+	if (msr <= 0x1fff)
+		return test_bit(msr, msr_bitmap + 0x000 / f);
+	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
+		return test_bit(msr & 0x1fff, msr_bitmap + 0x400 / f);
+	return true;
+}
+
+static inline bool vmx_test_msr_bitmap_write(ulong *msr_bitmap, u32 msr)
+{
+	int f = sizeof(unsigned long);
+
+	if (msr <= 0x1fff)
+		return test_bit(msr, msr_bitmap + 0x800 / f);
+	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
+		return test_bit(msr & 0x1fff, msr_bitmap + 0xc00 / f);
+	return true;
+}
+
+static inline void vmx_clear_msr_bitmap_read(ulong *msr_bitmap, u32 msr)
+{
+	int f = sizeof(unsigned long);
+
+	if (msr <= 0x1fff)
+		__clear_bit(msr, msr_bitmap + 0x000 / f);
+	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
+		__clear_bit(msr & 0x1fff, msr_bitmap + 0x400 / f);
+}
+
+static inline void vmx_clear_msr_bitmap_write(ulong *msr_bitmap, u32 msr)
+{
+	int f = sizeof(unsigned long);
+
+	if (msr <= 0x1fff)
+		__clear_bit(msr, msr_bitmap + 0x800 / f);
+	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
+		__clear_bit(msr & 0x1fff, msr_bitmap + 0xc00 / f);
+}
+
+static inline void vmx_set_msr_bitmap_read(ulong *msr_bitmap, u32 msr)
+{
+	int f = sizeof(unsigned long);
+
+	if (msr <= 0x1fff)
+		__set_bit(msr, msr_bitmap + 0x000 / f);
+	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
+		__set_bit(msr & 0x1fff, msr_bitmap + 0x400 / f);
+}
+
+static inline void vmx_set_msr_bitmap_write(ulong *msr_bitmap, u32 msr)
+{
+	int f = sizeof(unsigned long);
+
+	if (msr <= 0x1fff)
+		__set_bit(msr, msr_bitmap + 0x800 / f);
+	else if ((msr >= 0xc0000000) && (msr <= 0xc0001fff))
+		__set_bit(msr & 0x1fff, msr_bitmap + 0xc00 / f);
+}
+
+
 static inline u8 vmx_get_rvi(void)
 {
 	return vmcs_read16(GUEST_INTR_STATUS) & 0xff;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/vmx/vmx_ops.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/vmx/vmx_ops.h
@@ -8,7 +8,7 @@
 
 #include "evmcs.h"
 #include "vmcs.h"
-#include "x86.h"
+#include "../x86.h"
 
 asmlinkage void vmread_error(unsigned long field, bool fault);
 __attribute__((regparm(0))) void vmread_error_trampoline(unsigned long field,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/x86.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/x86.c
@@ -68,7 +68,9 @@
 #include <asm/mce.h>
 #include <asm/pkru.h>
 #include <linux/kernel_stat.h>
-#include <asm/fpu/internal.h> /* Ugh! */
+#include <asm/fpu/api.h>
+#include <asm/fpu/xcr.h>
+#include <asm/fpu/xstate.h>
 #include <asm/pvclock.h>
 #include <asm/div64.h>
 #include <asm/irq_remapping.h>
@@ -184,6 +186,10 @@
 int __read_mostly pi_inject_timer = -1;
 module_param(pi_inject_timer, bint, S_IRUGO | S_IWUSR);
 
+/* Enable/disable SMT_RSB bug mitigation */
+bool __read_mostly mitigate_smt_rsb;
+module_param(mitigate_smt_rsb, bool, 0444);
+
 /*
  * Restoring the host value for MSRs that are only consumed when running in
  * usermode, e.g. SYSCALL MSRs and TSC_AUX, can be deferred until the CPU
@@ -277,6 +283,8 @@
 	STATS_DESC_COUNTER(VCPU, nested_run),
 	STATS_DESC_COUNTER(VCPU, directed_yield_attempted),
 	STATS_DESC_COUNTER(VCPU, directed_yield_successful),
+	STATS_DESC_COUNTER(VCPU, preemption_reported),
+	STATS_DESC_COUNTER(VCPU, preemption_other),
 	STATS_DESC_ICOUNTER(VCPU, guest_mode)
 };
 
@@ -293,8 +301,6 @@
 u64 __read_mostly supported_xcr0;
 EXPORT_SYMBOL_GPL(supported_xcr0);
 
-static struct kmem_cache *x86_fpu_cache;
-
 static struct kmem_cache *x86_emulator_cache;
 
 /*
@@ -523,6 +529,7 @@
 #define EXCPT_TRAP		1
 #define EXCPT_ABORT		2
 #define EXCPT_INTERRUPT		3
+#define EXCPT_DB		4
 
 static int exception_type(int vector)
 {
@@ -533,8 +540,14 @@
 
 	mask = 1 << vector;
 
-	/* #DB is trap, as instruction watchpoints are handled elsewhere */
-	if (mask & ((1 << DB_VECTOR) | (1 << BP_VECTOR) | (1 << OF_VECTOR)))
+	/*
+	 * #DBs can be trap-like or fault-like, the caller must check other CPU
+	 * state, e.g. DR6, to determine whether a #DB is a trap or fault.
+	 */
+	if (mask & (1 << DB_VECTOR))
+		return EXCPT_DB;
+
+	if (mask & ((1 << BP_VECTOR) | (1 << OF_VECTOR)))
 		return EXCPT_TRAP;
 
 	if (mask & ((1 << DF_VECTOR) | (1 << MC_VECTOR)))
@@ -599,6 +612,12 @@
 }
 EXPORT_SYMBOL_GPL(kvm_deliver_exception_payload);
 
+/* Forcibly leave the nested mode in cases like a vCPU reset */
+static void kvm_leave_nested(struct kvm_vcpu *vcpu)
+{
+	kvm_x86_ops.nested_ops->leave_nested(vcpu);
+}
+
 static void kvm_multiple_exception(struct kvm_vcpu *vcpu,
 		unsigned nr, bool has_error, u32 error_code,
 	        bool has_payload, unsigned long payload, bool reinject)
@@ -848,6 +867,7 @@
 
 	memcpy(mmu->pdptrs, pdpte, sizeof(mmu->pdptrs));
 	kvm_register_mark_dirty(vcpu, VCPU_EXREG_PDPTR);
+	kvm_make_request(KVM_REQ_LOAD_MMU_PGD, vcpu);
 	vcpu->arch.pdptrs_from_userspace = false;
 
 out:
@@ -856,6 +876,22 @@
 }
 EXPORT_SYMBOL_GPL(load_pdptrs);
 
+static bool kvm_is_valid_cr0(struct kvm_vcpu *vcpu, unsigned long cr0)
+{
+#ifdef CONFIG_X86_64
+	if (cr0 & 0xffffffff00000000UL)
+		return false;
+#endif
+
+	if ((cr0 & X86_CR0_NW) && !(cr0 & X86_CR0_CD))
+		return false;
+
+	if ((cr0 & X86_CR0_PG) && !(cr0 & X86_CR0_PE))
+		return false;
+
+	return static_call(kvm_x86_is_valid_cr0)(vcpu, cr0);
+}
+
 void kvm_post_set_cr0(struct kvm_vcpu *vcpu, unsigned long old_cr0, unsigned long cr0)
 {
 	if ((cr0 ^ old_cr0) & X86_CR0_PG) {
@@ -878,20 +914,13 @@
 	unsigned long old_cr0 = kvm_read_cr0(vcpu);
 	unsigned long pdptr_bits = X86_CR0_CD | X86_CR0_NW | X86_CR0_PG;
 
-	cr0 |= X86_CR0_ET;
-
-#ifdef CONFIG_X86_64
-	if (cr0 & 0xffffffff00000000UL)
+	if (!kvm_is_valid_cr0(vcpu, cr0))
 		return 1;
-#endif
 
-	cr0 &= ~CR0_RESERVED_BITS;
-
-	if ((cr0 & X86_CR0_NW) && !(cr0 & X86_CR0_CD))
-		return 1;
+	cr0 |= X86_CR0_ET;
 
-	if ((cr0 & X86_CR0_PG) && !(cr0 & X86_CR0_PE))
-		return 1;
+	/* Write to CR0 reserved bits are ignored, even on Intel. */
+	cr0 &= ~CR0_RESERVED_BITS;
 
 #ifdef CONFIG_X86_64
 	if ((vcpu->arch.efer & EFER_LME) && !is_paging(vcpu) &&
@@ -1018,6 +1047,7 @@
 
 int kvm_emulate_xsetbv(struct kvm_vcpu *vcpu)
 {
+	/* Note, #UD due to CR4.OSXSAVE=0 has priority over the intercept. */
 	if (static_call(kvm_x86_get_cpl)(vcpu) != 0 ||
 	    __kvm_set_xcr(vcpu, kvm_rcx_read(vcpu), kvm_read_edx_eax(vcpu))) {
 		kvm_inject_gp(vcpu, 0);
@@ -1028,7 +1058,7 @@
 }
 EXPORT_SYMBOL_GPL(kvm_emulate_xsetbv);
 
-bool kvm_is_valid_cr4(struct kvm_vcpu *vcpu, unsigned long cr4)
+bool __kvm_is_valid_cr4(struct kvm_vcpu *vcpu, unsigned long cr4)
 {
 	if (cr4 & cr4_reserved_bits)
 		return false;
@@ -1036,9 +1066,15 @@
 	if (cr4 & vcpu->arch.cr4_guest_rsvd_bits)
 		return false;
 
-	return static_call(kvm_x86_is_valid_cr4)(vcpu, cr4);
+	return true;
+}
+EXPORT_SYMBOL_GPL(__kvm_is_valid_cr4);
+
+static bool kvm_is_valid_cr4(struct kvm_vcpu *vcpu, unsigned long cr4)
+{
+	return __kvm_is_valid_cr4(vcpu, cr4) &&
+	       static_call(kvm_x86_is_valid_cr4)(vcpu, cr4);
 }
-EXPORT_SYMBOL_GPL(kvm_is_valid_cr4);
 
 void kvm_post_set_cr4(struct kvm_vcpu *vcpu, unsigned long old_cr4, unsigned long cr4)
 {
@@ -1092,6 +1128,18 @@
 	int i;
 
 	/*
+	 * MOV CR3 and INVPCID are usually not intercepted when using TDP, but
+	 * this is reachable when running EPT=1 and unrestricted_guest=0,  and
+	 * also via the emulator.  KVM's TDP page tables are not in the scope of
+	 * the invalidation, but the guest's TLB entries need to be flushed as
+	 * the CPU may have cached entries in its TLB for the target PCID.
+	 */
+	if (unlikely(tdp_enabled)) {
+		kvm_make_request(KVM_REQ_TLB_FLUSH_GUEST, vcpu);
+		return;
+	}
+
+	/*
 	 * If neither the current CR3 nor any of the prev_roots use the given
 	 * PCID, then nothing needs to be done here because a resync will
 	 * happen anyway before switching to any other CR3.
@@ -1311,27 +1359,17 @@
 	MSR_IA32_UMWAIT_CONTROL,
 
 	MSR_ARCH_PERFMON_FIXED_CTR0, MSR_ARCH_PERFMON_FIXED_CTR1,
-	MSR_ARCH_PERFMON_FIXED_CTR0 + 2, MSR_ARCH_PERFMON_FIXED_CTR0 + 3,
+	MSR_ARCH_PERFMON_FIXED_CTR0 + 2,
 	MSR_CORE_PERF_FIXED_CTR_CTRL, MSR_CORE_PERF_GLOBAL_STATUS,
 	MSR_CORE_PERF_GLOBAL_CTRL, MSR_CORE_PERF_GLOBAL_OVF_CTRL,
 	MSR_ARCH_PERFMON_PERFCTR0, MSR_ARCH_PERFMON_PERFCTR1,
 	MSR_ARCH_PERFMON_PERFCTR0 + 2, MSR_ARCH_PERFMON_PERFCTR0 + 3,
 	MSR_ARCH_PERFMON_PERFCTR0 + 4, MSR_ARCH_PERFMON_PERFCTR0 + 5,
 	MSR_ARCH_PERFMON_PERFCTR0 + 6, MSR_ARCH_PERFMON_PERFCTR0 + 7,
-	MSR_ARCH_PERFMON_PERFCTR0 + 8, MSR_ARCH_PERFMON_PERFCTR0 + 9,
-	MSR_ARCH_PERFMON_PERFCTR0 + 10, MSR_ARCH_PERFMON_PERFCTR0 + 11,
-	MSR_ARCH_PERFMON_PERFCTR0 + 12, MSR_ARCH_PERFMON_PERFCTR0 + 13,
-	MSR_ARCH_PERFMON_PERFCTR0 + 14, MSR_ARCH_PERFMON_PERFCTR0 + 15,
-	MSR_ARCH_PERFMON_PERFCTR0 + 16, MSR_ARCH_PERFMON_PERFCTR0 + 17,
 	MSR_ARCH_PERFMON_EVENTSEL0, MSR_ARCH_PERFMON_EVENTSEL1,
 	MSR_ARCH_PERFMON_EVENTSEL0 + 2, MSR_ARCH_PERFMON_EVENTSEL0 + 3,
 	MSR_ARCH_PERFMON_EVENTSEL0 + 4, MSR_ARCH_PERFMON_EVENTSEL0 + 5,
 	MSR_ARCH_PERFMON_EVENTSEL0 + 6, MSR_ARCH_PERFMON_EVENTSEL0 + 7,
-	MSR_ARCH_PERFMON_EVENTSEL0 + 8, MSR_ARCH_PERFMON_EVENTSEL0 + 9,
-	MSR_ARCH_PERFMON_EVENTSEL0 + 10, MSR_ARCH_PERFMON_EVENTSEL0 + 11,
-	MSR_ARCH_PERFMON_EVENTSEL0 + 12, MSR_ARCH_PERFMON_EVENTSEL0 + 13,
-	MSR_ARCH_PERFMON_EVENTSEL0 + 14, MSR_ARCH_PERFMON_EVENTSEL0 + 15,
-	MSR_ARCH_PERFMON_EVENTSEL0 + 16, MSR_ARCH_PERFMON_EVENTSEL0 + 17,
 
 	MSR_K7_EVNTSEL0, MSR_K7_EVNTSEL1, MSR_K7_EVNTSEL2, MSR_K7_EVNTSEL3,
 	MSR_K7_PERFCTR0, MSR_K7_PERFCTR1, MSR_K7_PERFCTR2, MSR_K7_PERFCTR3,
@@ -1435,7 +1473,7 @@
 	MSR_IA32_VMX_EPT_VPID_CAP,
 	MSR_IA32_VMX_VMFUNC,
 
-	MSR_F10H_DECFG,
+	MSR_AMD64_DE_CFG,
 	MSR_IA32_UCODE_REV,
 	MSR_IA32_ARCH_CAPABILITIES,
 	MSR_IA32_PERF_CAPABILITIES,
@@ -1444,12 +1482,34 @@
 static u32 msr_based_features[ARRAY_SIZE(msr_based_features_all)];
 static unsigned int num_msr_based_features;
 
+/*
+ * Some IA32_ARCH_CAPABILITIES bits have dependencies on MSRs that KVM
+ * does not yet virtualize. These include:
+ *   10 - MISC_PACKAGE_CTRLS
+ *   11 - ENERGY_FILTERING_CTL
+ *   12 - DOITM
+ *   18 - FB_CLEAR_CTRL
+ *   21 - XAPIC_DISABLE_STATUS
+ *   23 - OVERCLOCKING_STATUS
+ */
+
+#define KVM_SUPPORTED_ARCH_CAP \
+	(ARCH_CAP_RDCL_NO | ARCH_CAP_IBRS_ALL | ARCH_CAP_RSBA | \
+	 ARCH_CAP_SKIP_VMENTRY_L1DFLUSH | ARCH_CAP_SSB_NO | ARCH_CAP_MDS_NO | \
+	 ARCH_CAP_PSCHANGE_MC_NO | ARCH_CAP_TSX_CTRL_MSR | ARCH_CAP_TAA_NO | \
+	 ARCH_CAP_SBDR_SSDP_NO | ARCH_CAP_FBSDP_NO | ARCH_CAP_PSDP_NO | \
+	 ARCH_CAP_FB_CLEAR | ARCH_CAP_RRSBA | ARCH_CAP_PBRSB_NO | ARCH_CAP_GDS_NO | \
+	 ARCH_CAP_BHI_NO | \
+	 ARCH_CAP_RFDS_NO | ARCH_CAP_RFDS_CLEAR)
+
 static u64 kvm_get_arch_capabilities(void)
 {
 	u64 data = 0;
 
-	if (boot_cpu_has(X86_FEATURE_ARCH_CAPABILITIES))
+	if (boot_cpu_has(X86_FEATURE_ARCH_CAPABILITIES)) {
 		rdmsrl(MSR_IA32_ARCH_CAPABILITIES, data);
+		data &= KVM_SUPPORTED_ARCH_CAP;
+	}
 
 	/*
 	 * If nx_huge_pages is enabled, KVM's shadow paging will ensure that
@@ -1477,6 +1537,8 @@
 		data |= ARCH_CAP_SSB_NO;
 	if (!boot_cpu_has_bug(X86_BUG_MDS))
 		data |= ARCH_CAP_MDS_NO;
+	if (!boot_cpu_has_bug(X86_BUG_RFDS))
+		data |= ARCH_CAP_RFDS_NO;
 
 	if (!boot_cpu_has(X86_FEATURE_RTM)) {
 		/*
@@ -1497,6 +1559,9 @@
 		 */
 	}
 
+	if (!boot_cpu_has_bug(X86_BUG_GDS) || gds_ucode_mitigated())
+		data |= ARCH_CAP_GDS_NO;
+
 	return data;
 }
 
@@ -1592,8 +1657,7 @@
 		return r;
 	}
 
-	/* Update reserved bits */
-	if ((efer ^ old_efer) & EFER_NX)
+	if ((efer ^ old_efer) & KVM_MMU_EFER_ROLE_BITS)
 		kvm_mmu_reset_context(vcpu);
 
 	return 0;
@@ -1685,7 +1749,7 @@
 		 * value, and that something deterministic happens if the guest
 		 * invokes 64-bit SYSENTER.
 		 */
-		data = get_canonical(data, vcpu_virt_addr_bits(vcpu));
+		data = __canonical_address(data, vcpu_virt_addr_bits(vcpu));
 		break;
 	case MSR_TSC_AUX:
 		if (!kvm_is_supported_user_return_msr(MSR_TSC_AUX))
@@ -3044,7 +3108,7 @@
 static bool can_set_mci_status(struct kvm_vcpu *vcpu)
 {
 	/* McStatusWrEn enabled? */
-	if (guest_cpuid_is_amd_or_hygon(vcpu))
+	if (guest_cpuid_is_amd_compatible(vcpu))
 		return !!(vcpu->arch.msr_hwcr & BIT_ULL(18));
 
 	return false;
@@ -3079,17 +3143,20 @@
 			/* only 0 or all 1s can be written to IA32_MCi_CTL
 			 * some Linux kernels though clear bit 10 in bank 4 to
 			 * workaround a BIOS/GART TBL issue on AMD K8s, ignore
-			 * this to avoid an uncatched #GP in the guest
+			 * this to avoid an uncatched #GP in the guest.
+			 *
+			 * UNIXWARE clears bit 0 of MC1_CTL to ignore
+			 * correctable, single-bit ECC data errors.
 			 */
 			if ((offset & 0x3) == 0 &&
-			    data != 0 && (data | (1 << 10)) != ~(u64)0)
-				return -1;
+			    data != 0 && (data | (1 << 10) | 1) != ~(u64)0)
+				return 1;
 
 			/* MCi_STATUS */
 			if (!msr_info->host_initiated &&
 			    (offset & 0x3) == 1 && data != 0) {
 				if (!can_set_mci_status(vcpu))
-					return -1;
+					return 1;
 			}
 
 			vcpu->arch.mce_banks[offset] = data;
@@ -3193,10 +3260,37 @@
 	static_call(kvm_x86_tlb_flush_guest)(vcpu);
 }
 
+
+static inline void kvm_vcpu_flush_tlb_current(struct kvm_vcpu *vcpu)
+{
+	++vcpu->stat.tlb_flush;
+	static_call(kvm_x86_tlb_flush_current)(vcpu);
+}
+
+/*
+ * Service "local" TLB flush requests, which are specific to the current MMU
+ * context.  In addition to the generic event handling in vcpu_enter_guest(),
+ * TLB flushes that are targeted at an MMU context also need to be serviced
+ * prior before nested VM-Enter/VM-Exit.
+ */
+void kvm_service_local_tlb_flush_requests(struct kvm_vcpu *vcpu)
+{
+	if (kvm_check_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu))
+		kvm_vcpu_flush_tlb_current(vcpu);
+
+	if (kvm_check_request(KVM_REQ_TLB_FLUSH_GUEST, vcpu))
+		kvm_vcpu_flush_tlb_guest(vcpu);
+}
+EXPORT_SYMBOL_GPL(kvm_service_local_tlb_flush_requests);
+
 static void record_steal_time(struct kvm_vcpu *vcpu)
 {
-	struct kvm_host_map map;
-	struct kvm_steal_time *st;
+	struct gfn_to_hva_cache *ghc = &vcpu->arch.st.cache;
+	struct kvm_steal_time __user *st;
+	struct kvm_memslots *slots;
+	gpa_t gpa = vcpu->arch.st.msr_val & KVM_STEAL_VALID_BITS;
+	u64 steal;
+	u32 version;
 
 	if (kvm_xen_msr_enabled(vcpu->kvm)) {
 		kvm_xen_runstate_set_running(vcpu);
@@ -3206,47 +3300,85 @@
 	if (!(vcpu->arch.st.msr_val & KVM_MSR_ENABLED))
 		return;
 
-	/* -EAGAIN is returned in atomic context so we can just return. */
-	if (kvm_map_gfn(vcpu, vcpu->arch.st.msr_val >> PAGE_SHIFT,
-			&map, &vcpu->arch.st.cache, false))
+	if (WARN_ON_ONCE(current->mm != vcpu->kvm->mm))
 		return;
 
-	st = map.hva +
-		offset_in_page(vcpu->arch.st.msr_val & KVM_STEAL_VALID_BITS);
+	slots = kvm_memslots(vcpu->kvm);
+
+	if (unlikely(slots->generation != ghc->generation ||
+		     gpa != ghc->gpa ||
+		     kvm_is_error_hva(ghc->hva) || !ghc->memslot)) {
+		/* We rely on the fact that it fits in a single page. */
+		BUILD_BUG_ON((sizeof(*st) - 1) & KVM_STEAL_VALID_BITS);
 
+		if (kvm_gfn_to_hva_cache_init(vcpu->kvm, ghc, gpa, sizeof(*st)) ||
+		    kvm_is_error_hva(ghc->hva) || !ghc->memslot)
+			return;
+	}
+
+	st = (struct kvm_steal_time __user *)ghc->hva;
 	/*
 	 * Doing a TLB flush here, on the guest's behalf, can avoid
 	 * expensive IPIs.
 	 */
 	if (guest_pv_has(vcpu, KVM_FEATURE_PV_TLB_FLUSH)) {
-		u8 st_preempted = xchg(&st->preempted, 0);
+		u8 st_preempted = 0;
+		int err = -EFAULT;
+
+		if (!user_access_begin(st, sizeof(*st)))
+			return;
+
+		asm volatile("1: xchgb %0, %2\n"
+			     "xor %1, %1\n"
+			     "2:\n"
+			     _ASM_EXTABLE_UA(1b, 2b)
+			     : "+q" (st_preempted),
+			       "+&r" (err),
+			       "+m" (st->preempted));
+		if (err)
+			goto out;
+
+		user_access_end();
+
+		vcpu->arch.st.preempted = 0;
 
 		trace_kvm_pv_tlb_flush(vcpu->vcpu_id,
 				       st_preempted & KVM_VCPU_FLUSH_TLB);
 		if (st_preempted & KVM_VCPU_FLUSH_TLB)
 			kvm_vcpu_flush_tlb_guest(vcpu);
+
+		if (!user_access_begin(st, sizeof(*st)))
+			goto dirty;
 	} else {
-		st->preempted = 0;
-	}
+		if (!user_access_begin(st, sizeof(*st)))
+			return;
 
-	vcpu->arch.st.preempted = 0;
+		unsafe_put_user(0, &st->preempted, out);
+		vcpu->arch.st.preempted = 0;
+	}
 
-	if (st->version & 1)
-		st->version += 1;  /* first time write, random junk */
+	unsafe_get_user(version, &st->version, out);
+	if (version & 1)
+		version += 1;  /* first time write, random junk */
 
-	st->version += 1;
+	version += 1;
+	unsafe_put_user(version, &st->version, out);
 
 	smp_wmb();
 
-	st->steal += current->sched_info.run_delay -
+	unsafe_get_user(steal, &st->steal, out);
+	steal += current->sched_info.run_delay -
 		vcpu->arch.st.last_steal;
 	vcpu->arch.st.last_steal = current->sched_info.run_delay;
+	unsafe_put_user(steal, &st->steal, out);
 
-	smp_wmb();
+	version += 1;
+	unsafe_put_user(version, &st->version, out);
 
-	st->version += 1;
-
-	kvm_unmap_gfn(vcpu, &map, &vcpu->arch.st.cache, true, false);
+ out:
+	user_access_end();
+ dirty:
+	mark_page_dirty_in_slot(vcpu->kvm, ghc->memslot, gpa_to_gfn(ghc->gpa));
 }
 
 int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
@@ -3265,6 +3397,7 @@
 	case MSR_AMD64_PATCH_LOADER:
 	case MSR_AMD64_BU_CFG2:
 	case MSR_AMD64_DC_CFG:
+	case MSR_AMD64_TW_CFG:
 	case MSR_F15H_EX_CFG:
 		break;
 
@@ -3282,7 +3415,7 @@
 
 		if (!msr_info->host_initiated)
 			return 1;
-		if (guest_cpuid_has(vcpu, X86_FEATURE_PDCM) && kvm_get_msr_feature(&msr_ent))
+		if (kvm_get_msr_feature(&msr_ent))
 			return 1;
 		if (data & ~msr_ent.data)
 			return 1;
@@ -3376,6 +3509,7 @@
 		if (data & ~supported_xss)
 			return 1;
 		vcpu->arch.ia32_xss = data;
+		kvm_update_cpuid_runtime(vcpu);
 		break;
 	case MSR_SMI_COUNT:
 		if (!msr_info->host_initiated)
@@ -3604,6 +3738,7 @@
 	case MSR_AMD64_BU_CFG2:
 	case MSR_IA32_PERF_CTL:
 	case MSR_AMD64_DC_CFG:
+	case MSR_AMD64_TW_CFG:
 	case MSR_F15H_EX_CFG:
 	/*
 	 * Intel Sandy Bridge CPUs must support the RAPL (running average power
@@ -4051,10 +4186,15 @@
 		r = KVM_CLOCK_TSC_STABLE;
 		break;
 	case KVM_CAP_X86_DISABLE_EXITS:
-		r |=  KVM_X86_DISABLE_EXITS_HLT | KVM_X86_DISABLE_EXITS_PAUSE |
-		      KVM_X86_DISABLE_EXITS_CSTATE;
-		if(kvm_can_mwait_in_guest())
-			r |= KVM_X86_DISABLE_EXITS_MWAIT;
+		r = KVM_X86_DISABLE_EXITS_PAUSE;
+
+		if (!mitigate_smt_rsb) {
+			r |= KVM_X86_DISABLE_EXITS_HLT |
+			     KVM_X86_DISABLE_EXITS_CSTATE;
+
+			if (kvm_can_mwait_in_guest())
+				r |= KVM_X86_DISABLE_EXITS_MWAIT;
+		}
 		break;
 	case KVM_CAP_X86_SMM:
 		/* SMBASE is usually relocated above 1M on modern chipsets,
@@ -4285,44 +4425,70 @@
 
 static void kvm_steal_time_set_preempted(struct kvm_vcpu *vcpu)
 {
-	struct kvm_host_map map;
-	struct kvm_steal_time *st;
+	struct gfn_to_hva_cache *ghc = &vcpu->arch.st.cache;
+	struct kvm_steal_time __user *st;
+	struct kvm_memslots *slots;
+	static const u8 preempted = KVM_VCPU_PREEMPTED;
+	gpa_t gpa = vcpu->arch.st.msr_val & KVM_STEAL_VALID_BITS;
+
+	/*
+	 * The vCPU can be marked preempted if and only if the VM-Exit was on
+	 * an instruction boundary and will not trigger guest emulation of any
+	 * kind (see vcpu_run).  Vendor specific code controls (conservatively)
+	 * when this is true, for example allowing the vCPU to be marked
+	 * preempted if and only if the VM-Exit was due to a host interrupt.
+	 */
+	if (!vcpu->arch.at_instruction_boundary) {
+		vcpu->stat.preemption_other++;
+		return;
+	}
 
+	vcpu->stat.preemption_reported++;
 	if (!(vcpu->arch.st.msr_val & KVM_MSR_ENABLED))
 		return;
 
 	if (vcpu->arch.st.preempted)
 		return;
 
-	if (kvm_map_gfn(vcpu, vcpu->arch.st.msr_val >> PAGE_SHIFT, &map,
-			&vcpu->arch.st.cache, true))
+	/* This happens on process exit */
+	if (unlikely(current->mm != vcpu->kvm->mm))
 		return;
 
-	st = map.hva +
-		offset_in_page(vcpu->arch.st.msr_val & KVM_STEAL_VALID_BITS);
+	slots = kvm_memslots(vcpu->kvm);
+
+	if (unlikely(slots->generation != ghc->generation ||
+		     gpa != ghc->gpa ||
+		     kvm_is_error_hva(ghc->hva) || !ghc->memslot))
+		return;
 
-	st->preempted = vcpu->arch.st.preempted = KVM_VCPU_PREEMPTED;
+	st = (struct kvm_steal_time __user *)ghc->hva;
+	BUILD_BUG_ON(sizeof(st->preempted) != sizeof(preempted));
 
-	kvm_unmap_gfn(vcpu, &map, &vcpu->arch.st.cache, true, true);
+	if (!copy_to_user_nofault(&st->preempted, &preempted, sizeof(preempted)))
+		vcpu->arch.st.preempted = KVM_VCPU_PREEMPTED;
+
+	mark_page_dirty_in_slot(vcpu->kvm, ghc->memslot, gpa_to_gfn(ghc->gpa));
 }
 
 void kvm_arch_vcpu_put(struct kvm_vcpu *vcpu)
 {
 	int idx;
 
-	if (vcpu->preempted && !vcpu->arch.guest_state_protected)
-		vcpu->arch.preempted_in_kernel = !static_call(kvm_x86_get_cpl)(vcpu);
+	if (vcpu->preempted) {
+		if (!vcpu->arch.guest_state_protected)
+			vcpu->arch.preempted_in_kernel = !static_call(kvm_x86_get_cpl)(vcpu);
 
-	/*
-	 * Take the srcu lock as memslots will be accessed to check the gfn
-	 * cache generation against the memslots generation.
-	 */
-	idx = srcu_read_lock(&vcpu->kvm->srcu);
-	if (kvm_xen_msr_enabled(vcpu->kvm))
-		kvm_xen_runstate_set_preempted(vcpu);
-	else
-		kvm_steal_time_set_preempted(vcpu);
-	srcu_read_unlock(&vcpu->kvm->srcu, idx);
+		/*
+		 * Take the srcu lock as memslots will be accessed to check the gfn
+		 * cache generation against the memslots generation.
+		 */
+		idx = srcu_read_lock(&vcpu->kvm->srcu);
+		if (kvm_xen_msr_enabled(vcpu->kvm))
+			kvm_xen_runstate_set_preempted(vcpu);
+		else
+			kvm_steal_time_set_preempted(vcpu);
+		srcu_read_unlock(&vcpu->kvm->srcu, idx);
+	}
 
 	static_call(kvm_x86_vcpu_put)(vcpu);
 	vcpu->arch.last_host_tsc = rdtsc();
@@ -4331,8 +4497,7 @@
 static int kvm_vcpu_ioctl_get_lapic(struct kvm_vcpu *vcpu,
 				    struct kvm_lapic_state *s)
 {
-	if (vcpu->arch.apicv_active)
-		static_call(kvm_x86_sync_pir_to_irr)(vcpu);
+	static_call_cond(kvm_x86_sync_pir_to_irr)(vcpu);
 
 	return kvm_apic_get_state(vcpu, s);
 }
@@ -4642,8 +4807,10 @@
 		vcpu->arch.apic->sipi_vector = events->sipi_vector;
 
 	if (events->flags & KVM_VCPUEVENT_VALID_SMM) {
-		if (!!(vcpu->arch.hflags & HF_SMM_MASK) != events->smi.smm)
+		if (!!(vcpu->arch.hflags & HF_SMM_MASK) != events->smi.smm) {
+			kvm_leave_nested(vcpu);
 			kvm_smm_changed(vcpu, events->smi.smm);
+		}
 
 		vcpu->arch.smi_pending = events->smi.pending;
 
@@ -4672,12 +4839,11 @@
 {
 	unsigned long val;
 
+	memset(dbgregs, 0, sizeof(*dbgregs));
 	memcpy(dbgregs->db, vcpu->arch.db, sizeof(vcpu->arch.db));
 	kvm_get_dr(vcpu, 6, &val);
 	dbgregs->dr6 = val;
 	dbgregs->dr7 = vcpu->arch.dr7;
-	dbgregs->flags = 0;
-	memset(&dbgregs->reserved, 0, sizeof(dbgregs->reserved));
 }
 
 static int kvm_vcpu_ioctl_x86_set_debugregs(struct kvm_vcpu *vcpu,
@@ -4700,144 +4866,48 @@
 	return 0;
 }
 
-#define XSTATE_COMPACTION_ENABLED (1ULL << 63)
 
-static void fill_xsave(u8 *dest, struct kvm_vcpu *vcpu)
+static void kvm_vcpu_ioctl_x86_get_xsave2(struct kvm_vcpu *vcpu,
+					  u8 *state, unsigned int size)
 {
-	struct xregs_state *xsave = &vcpu->arch.guest_fpu->state.xsave;
-	u64 xstate_bv = xsave->header.xfeatures;
-	u64 valid;
-
-	/*
-	 * Copy legacy XSAVE area, to avoid complications with CPUID
-	 * leaves 0 and 1 in the loop below.
-	 */
-	memcpy(dest, xsave, XSAVE_HDR_OFFSET);
-
-	/* Set XSTATE_BV */
-	xstate_bv &= vcpu->arch.guest_supported_xcr0 | XFEATURE_MASK_FPSSE;
-	*(u64 *)(dest + XSAVE_HDR_OFFSET) = xstate_bv;
-
 	/*
-	 * Copy each region from the possibly compacted offset to the
-	 * non-compacted offset.
-	 */
-	valid = xstate_bv & ~XFEATURE_MASK_FPSSE;
-	while (valid) {
-		u32 size, offset, ecx, edx;
-		u64 xfeature_mask = valid & -valid;
-		int xfeature_nr = fls64(xfeature_mask) - 1;
-		void *src;
-
-		cpuid_count(XSTATE_CPUID, xfeature_nr,
-			    &size, &offset, &ecx, &edx);
-
-		if (xfeature_nr == XFEATURE_PKRU) {
-			memcpy(dest + offset, &vcpu->arch.pkru,
-			       sizeof(vcpu->arch.pkru));
-		} else {
-			src = get_xsave_addr(xsave, xfeature_nr);
-			if (src)
-				memcpy(dest + offset, src, size);
-		}
-
-		valid -= xfeature_mask;
-	}
-}
-
-static void load_xsave(struct kvm_vcpu *vcpu, u8 *src)
-{
-	struct xregs_state *xsave = &vcpu->arch.guest_fpu->state.xsave;
-	u64 xstate_bv = *(u64 *)(src + XSAVE_HDR_OFFSET);
-	u64 valid;
-
-	/*
-	 * Copy legacy XSAVE area, to avoid complications with CPUID
-	 * leaves 0 and 1 in the loop below.
-	 */
-	memcpy(xsave, src, XSAVE_HDR_OFFSET);
-
-	/* Set XSTATE_BV and possibly XCOMP_BV.  */
-	xsave->header.xfeatures = xstate_bv;
-	if (boot_cpu_has(X86_FEATURE_XSAVES))
-		xsave->header.xcomp_bv = host_xcr0 | XSTATE_COMPACTION_ENABLED;
-
-	/*
-	 * Copy each region from the non-compacted offset to the
-	 * possibly compacted offset.
+	 * Only copy state for features that are enabled for the guest.  The
+	 * state itself isn't problematic, but setting bits in the header for
+	 * features that are supported in *this* host but not exposed to the
+	 * guest can result in KVM_SET_XSAVE failing when live migrating to a
+	 * compatible host without the features that are NOT exposed to the
+	 * guest.
+	 *
+	 * FP+SSE can always be saved/restored via KVM_{G,S}ET_XSAVE, even if
+	 * XSAVE/XCRO are not exposed to the guest, and even if XSAVE isn't
+	 * supported by the host.
 	 */
-	valid = xstate_bv & ~XFEATURE_MASK_FPSSE;
-	while (valid) {
-		u32 size, offset, ecx, edx;
-		u64 xfeature_mask = valid & -valid;
-		int xfeature_nr = fls64(xfeature_mask) - 1;
+	u64 supported_xcr0 = vcpu->arch.guest_supported_xcr0 |
+			     XFEATURE_MASK_FPSSE;
 
-		cpuid_count(XSTATE_CPUID, xfeature_nr,
-			    &size, &offset, &ecx, &edx);
-
-		if (xfeature_nr == XFEATURE_PKRU) {
-			memcpy(&vcpu->arch.pkru, src + offset,
-			       sizeof(vcpu->arch.pkru));
-		} else {
-			void *dest = get_xsave_addr(xsave, xfeature_nr);
-
-			if (dest)
-				memcpy(dest, src + offset, size);
-		}
+	if (fpstate_is_confidential(&vcpu->arch.guest_fpu))
+		return;
 
-		valid -= xfeature_mask;
-	}
+	fpu_copy_guest_fpstate_to_uabi(&vcpu->arch.guest_fpu, state, size,
+				       supported_xcr0, vcpu->arch.pkru);
 }
 
 static void kvm_vcpu_ioctl_x86_get_xsave(struct kvm_vcpu *vcpu,
 					 struct kvm_xsave *guest_xsave)
 {
-	if (!vcpu->arch.guest_fpu)
-		return;
-
-	if (boot_cpu_has(X86_FEATURE_XSAVE)) {
-		memset(guest_xsave, 0, sizeof(struct kvm_xsave));
-		fill_xsave((u8 *) guest_xsave->region, vcpu);
-	} else {
-		memcpy(guest_xsave->region,
-			&vcpu->arch.guest_fpu->state.fxsave,
-			sizeof(struct fxregs_state));
-		*(u64 *)&guest_xsave->region[XSAVE_HDR_OFFSET / sizeof(u32)] =
-			XFEATURE_MASK_FPSSE;
-	}
+	return kvm_vcpu_ioctl_x86_get_xsave2(vcpu, (void *)guest_xsave->region,
+					     sizeof(guest_xsave->region));
 }
 
-#define XSAVE_MXCSR_OFFSET 24
-
 static int kvm_vcpu_ioctl_x86_set_xsave(struct kvm_vcpu *vcpu,
 					struct kvm_xsave *guest_xsave)
 {
-	u64 xstate_bv;
-	u32 mxcsr;
-
-	if (!vcpu->arch.guest_fpu)
+	if (fpstate_is_confidential(&vcpu->arch.guest_fpu))
 		return 0;
 
-	xstate_bv = *(u64 *)&guest_xsave->region[XSAVE_HDR_OFFSET / sizeof(u32)];
-	mxcsr = *(u32 *)&guest_xsave->region[XSAVE_MXCSR_OFFSET / sizeof(u32)];
-
-	if (boot_cpu_has(X86_FEATURE_XSAVE)) {
-		/*
-		 * Here we allow setting states that are not present in
-		 * CPUID leaf 0xD, index 0, EDX:EAX.  This is for compatibility
-		 * with old userspace.
-		 */
-		if (xstate_bv & ~supported_xcr0 || mxcsr & ~mxcsr_feature_mask)
-			return -EINVAL;
-		load_xsave(vcpu, (u8 *)guest_xsave->region);
-	} else {
-		if (xstate_bv & ~XFEATURE_MASK_FPSSE ||
-			mxcsr & ~mxcsr_feature_mask)
-			return -EINVAL;
-		memcpy(&vcpu->arch.guest_fpu->state.fxsave,
-			guest_xsave->region, sizeof(struct fxregs_state));
-	}
-	return 0;
+	return fpu_copy_uabi_to_guest_fpstate(&vcpu->arch.guest_fpu,
+					      guest_xsave->region,
+					      supported_xcr0, &vcpu->arch.pkru);
 }
 
 static void kvm_vcpu_ioctl_x86_get_xcrs(struct kvm_vcpu *vcpu,
@@ -5606,15 +5676,26 @@
 		if (cap->args[0] & ~KVM_X86_DISABLE_VALID_EXITS)
 			break;
 
-		if ((cap->args[0] & KVM_X86_DISABLE_EXITS_MWAIT) &&
-			kvm_can_mwait_in_guest())
-			kvm->arch.mwait_in_guest = true;
-		if (cap->args[0] & KVM_X86_DISABLE_EXITS_HLT)
-			kvm->arch.hlt_in_guest = true;
 		if (cap->args[0] & KVM_X86_DISABLE_EXITS_PAUSE)
 			kvm->arch.pause_in_guest = true;
-		if (cap->args[0] & KVM_X86_DISABLE_EXITS_CSTATE)
-			kvm->arch.cstate_in_guest = true;
+
+#define SMT_RSB_MSG "This processor is affected by the Cross-Thread Return Predictions vulnerability. " \
+		    "KVM_CAP_X86_DISABLE_EXITS should only be used with SMT disabled or trusted guests."
+
+		if (!mitigate_smt_rsb) {
+			if (boot_cpu_has_bug(X86_BUG_SMT_RSB) && cpu_smt_possible() &&
+			    (cap->args[0] & ~KVM_X86_DISABLE_EXITS_PAUSE))
+				pr_warn_once(SMT_RSB_MSG);
+
+			if ((cap->args[0] & KVM_X86_DISABLE_EXITS_MWAIT) &&
+			    kvm_can_mwait_in_guest())
+				kvm->arch.mwait_in_guest = true;
+			if (cap->args[0] & KVM_X86_DISABLE_EXITS_HLT)
+				kvm->arch.hlt_in_guest = true;
+			if (cap->args[0] & KVM_X86_DISABLE_EXITS_CSTATE)
+				kvm->arch.cstate_in_guest = true;
+		}
+
 		r = 0;
 		break;
 	case KVM_CAP_MSR_PLATFORM_INFO:
@@ -5626,6 +5707,11 @@
 		r = 0;
 		break;
 	case KVM_CAP_X86_USER_SPACE_MSR:
+		r = -EINVAL;
+		if (cap->args[0] & ~(KVM_MSR_EXIT_REASON_INVAL |
+				     KVM_MSR_EXIT_REASON_UNKNOWN |
+				     KVM_MSR_EXIT_REASON_FILTER))
+			break;
 		kvm->arch.user_space_msr_mask = cap->args[0];
 		r = 0;
 		break;
@@ -5746,23 +5832,22 @@
 	return 0;
 }
 
-static int kvm_vm_ioctl_set_msr_filter(struct kvm *kvm, void __user *argp)
+static int kvm_vm_ioctl_set_msr_filter(struct kvm *kvm,
+				       struct kvm_msr_filter *filter)
 {
-	struct kvm_msr_filter __user *user_msr_filter = argp;
 	struct kvm_x86_msr_filter *new_filter, *old_filter;
-	struct kvm_msr_filter filter;
 	bool default_allow;
 	bool empty = true;
 	int r = 0;
 	u32 i;
 
-	if (copy_from_user(&filter, user_msr_filter, sizeof(filter)))
-		return -EFAULT;
+	if (filter->flags & ~KVM_MSR_FILTER_DEFAULT_DENY)
+		return -EINVAL;
 
-	for (i = 0; i < ARRAY_SIZE(filter.ranges); i++)
-		empty &= !filter.ranges[i].nmsrs;
+	for (i = 0; i < ARRAY_SIZE(filter->ranges); i++)
+		empty &= !filter->ranges[i].nmsrs;
 
-	default_allow = !(filter.flags & KVM_MSR_FILTER_DEFAULT_DENY);
+	default_allow = !(filter->flags & KVM_MSR_FILTER_DEFAULT_DENY);
 	if (empty && !default_allow)
 		return -EINVAL;
 
@@ -5770,8 +5855,8 @@
 	if (!new_filter)
 		return -ENOMEM;
 
-	for (i = 0; i < ARRAY_SIZE(filter.ranges); i++) {
-		r = kvm_add_msr_filter(new_filter, &filter.ranges[i]);
+	for (i = 0; i < ARRAY_SIZE(filter->ranges); i++) {
+		r = kvm_add_msr_filter(new_filter, &filter->ranges[i]);
 		if (r) {
 			kvm_free_msr_filter(new_filter);
 			return r;
@@ -5794,6 +5879,62 @@
 	return 0;
 }
 
+#ifdef CONFIG_KVM_COMPAT
+/* for KVM_X86_SET_MSR_FILTER */
+struct kvm_msr_filter_range_compat {
+	__u32 flags;
+	__u32 nmsrs;
+	__u32 base;
+	__u32 bitmap;
+};
+
+struct kvm_msr_filter_compat {
+	__u32 flags;
+	struct kvm_msr_filter_range_compat ranges[KVM_MSR_FILTER_MAX_RANGES];
+};
+
+#define KVM_X86_SET_MSR_FILTER_COMPAT _IOW(KVMIO, 0xc6, struct kvm_msr_filter_compat)
+
+long kvm_arch_vm_compat_ioctl(struct file *filp, unsigned int ioctl,
+			      unsigned long arg)
+{
+	void __user *argp = (void __user *)arg;
+	struct kvm *kvm = filp->private_data;
+	long r = -ENOTTY;
+
+	switch (ioctl) {
+	case KVM_X86_SET_MSR_FILTER_COMPAT: {
+		struct kvm_msr_filter __user *user_msr_filter = argp;
+		struct kvm_msr_filter_compat filter_compat;
+		struct kvm_msr_filter filter;
+		int i;
+
+		if (copy_from_user(&filter_compat, user_msr_filter,
+				   sizeof(filter_compat)))
+			return -EFAULT;
+
+		filter.flags = filter_compat.flags;
+		for (i = 0; i < ARRAY_SIZE(filter.ranges); i++) {
+			struct kvm_msr_filter_range_compat *cr;
+
+			cr = &filter_compat.ranges[i];
+			filter.ranges[i] = (struct kvm_msr_filter_range) {
+				.flags = cr->flags,
+				.nmsrs = cr->nmsrs,
+				.base = cr->base,
+				.bitmap = (__u8 *)(ulong)cr->bitmap,
+			};
+		}
+
+		r = kvm_vm_ioctl_set_msr_filter(kvm, &filter);
+		break;
+	}
+	}
+
+	return r;
+}
+#endif
+
 #ifdef CONFIG_HAVE_KVM_PM_NOTIFIER
 static int kvm_arch_suspend_notifier(struct kvm *kvm)
 {
@@ -6168,9 +6309,16 @@
 	case KVM_SET_PMU_EVENT_FILTER:
 		r = kvm_vm_ioctl_set_pmu_event_filter(kvm, argp);
 		break;
-	case KVM_X86_SET_MSR_FILTER:
-		r = kvm_vm_ioctl_set_msr_filter(kvm, argp);
+	case KVM_X86_SET_MSR_FILTER: {
+		struct kvm_msr_filter __user *user_msr_filter = argp;
+		struct kvm_msr_filter filter;
+
+		if (copy_from_user(&filter, user_msr_filter, sizeof(filter)))
+			return -EFAULT;
+
+		r = kvm_vm_ioctl_set_msr_filter(kvm, &filter);
 		break;
+	}
 	default:
 		r = -ENOTTY;
 	}
@@ -6238,12 +6386,12 @@
 				intel_pt_validate_hw_cap(PT_CAP_num_address_ranges) * 2)
 				continue;
 			break;
-		case MSR_ARCH_PERFMON_PERFCTR0 ... MSR_ARCH_PERFMON_PERFCTR0 + 17:
+		case MSR_ARCH_PERFMON_PERFCTR0 ... MSR_ARCH_PERFMON_PERFCTR0 + 7:
 			if (msrs_to_save_all[i] - MSR_ARCH_PERFMON_PERFCTR0 >=
 			    min(INTEL_PMC_MAX_GENERIC, x86_pmu.num_counters_gp))
 				continue;
 			break;
-		case MSR_ARCH_PERFMON_EVENTSEL0 ... MSR_ARCH_PERFMON_EVENTSEL0 + 17:
+		case MSR_ARCH_PERFMON_EVENTSEL0 ... MSR_ARCH_PERFMON_EVENTSEL0 + 7:
 			if (msrs_to_save_all[i] - MSR_ARCH_PERFMON_EVENTSEL0 >=
 			    min(INTEL_PMC_MAX_GENERIC, x86_pmu.num_counters_gp))
 				continue;
@@ -6803,15 +6951,8 @@
 				   exception, &write_emultor);
 }
 
-#define CMPXCHG_TYPE(t, ptr, old, new) \
-	(cmpxchg((t *)(ptr), *(t *)(old), *(t *)(new)) == *(t *)(old))
-
-#ifdef CONFIG_X86_64
-#  define CMPXCHG64(ptr, old, new) CMPXCHG_TYPE(u64, ptr, old, new)
-#else
-#  define CMPXCHG64(ptr, old, new) \
-	(cmpxchg64((u64 *)(ptr), *(u64 *)(old), *(u64 *)(new)) == *(u64 *)(old))
-#endif
+#define emulator_try_cmpxchg_user(t, ptr, old, new) \
+	(__try_cmpxchg_user((t __user *)(ptr), (t *)(old), *(t *)(new), efault ## t))
 
 static int emulator_cmpxchg_emulated(struct x86_emulate_ctxt *ctxt,
 				     unsigned long addr,
@@ -6820,12 +6961,11 @@
 				     unsigned int bytes,
 				     struct x86_exception *exception)
 {
-	struct kvm_host_map map;
 	struct kvm_vcpu *vcpu = emul_to_vcpu(ctxt);
 	u64 page_line_mask;
+	unsigned long hva;
 	gpa_t gpa;
-	char *kaddr;
-	bool exchanged;
+	int r;
 
 	/* guests cmpxchg8b have to be emulated atomically */
 	if (bytes > 8 || (bytes & (bytes - 1)))
@@ -6849,31 +6989,42 @@
 	if (((gpa + bytes - 1) & page_line_mask) != (gpa & page_line_mask))
 		goto emul_write;
 
-	if (kvm_vcpu_map(vcpu, gpa_to_gfn(gpa), &map))
+	hva = kvm_vcpu_gfn_to_hva(vcpu, gpa_to_gfn(gpa));
+	if (kvm_is_error_hva(hva))
 		goto emul_write;
 
-	kaddr = map.hva + offset_in_page(gpa);
+	hva += offset_in_page(gpa);
 
 	switch (bytes) {
 	case 1:
-		exchanged = CMPXCHG_TYPE(u8, kaddr, old, new);
+		r = emulator_try_cmpxchg_user(u8, hva, old, new);
 		break;
 	case 2:
-		exchanged = CMPXCHG_TYPE(u16, kaddr, old, new);
+		r = emulator_try_cmpxchg_user(u16, hva, old, new);
 		break;
 	case 4:
-		exchanged = CMPXCHG_TYPE(u32, kaddr, old, new);
+		r = emulator_try_cmpxchg_user(u32, hva, old, new);
 		break;
 	case 8:
-		exchanged = CMPXCHG64(kaddr, old, new);
+		r = emulator_try_cmpxchg_user(u64, hva, old, new);
 		break;
 	default:
 		BUG();
 	}
 
-	kvm_vcpu_unmap(vcpu, &map, true);
+	if (r < 0)
+		return X86EMUL_UNHANDLEABLE;
+
+	/*
+	 * Mark the page dirty _before_ checking whether or not the CMPXCHG was
+	 * successful, as the old value is written back on failure.  Note, for
+	 * live migration, this is unnecessarily conservative as CMPXCHG writes
+	 * back the original value and the access is atomic, but KVM's ABI is
+	 * that all writes are dirty logged, regardless of the value written.
+	 */
+	kvm_vcpu_mark_page_dirty(vcpu, gpa_to_gfn(gpa));
 
-	if (!exchanged)
+	if (r)
 		return X86EMUL_CMPXCHG_FAILED;
 
 	kvm_page_track_write(vcpu, gpa, new, bytes);
@@ -6948,7 +7099,13 @@
 			   unsigned short port, void *val, unsigned int count)
 {
 	if (vcpu->arch.pio.count) {
-		/* Complete previous iteration.  */
+		/*
+		 * Complete a previous iteration that required userspace I/O.
+		 * Note, @count isn't guaranteed to match pio.count as userspace
+		 * can modify ECX before rerunning the vCPU.  Ignore any such
+		 * shenanigans as KVM doesn't support modifying the rep count,
+		 * and the emulator ensures @count doesn't overflow the buffer.
+		 */
 	} else {
 		int r = __emulator_pio_in(vcpu, size, port, count);
 		if (!r)
@@ -6957,7 +7114,6 @@
 		/* Results already available, fall through.  */
 	}
 
-	WARN_ON(count != vcpu->arch.pio.count);
 	complete_emulator_pio_in(vcpu, val);
 	return 1;
 }
@@ -7300,6 +7456,11 @@
 	return guest_cpuid_has(emul_to_vcpu(ctxt), X86_FEATURE_FXSR);
 }
 
+static bool emulator_guest_has_rdpid(struct x86_emulate_ctxt *ctxt)
+{
+	return guest_cpuid_has(emul_to_vcpu(ctxt), X86_FEATURE_RDPID);
+}
+
 static ulong emulator_read_gpr(struct x86_emulate_ctxt *ctxt, unsigned reg)
 {
 	return kvm_register_read_raw(emul_to_vcpu(ctxt), reg);
@@ -7382,6 +7543,7 @@
 	.guest_has_long_mode = emulator_guest_has_long_mode,
 	.guest_has_movbe     = emulator_guest_has_movbe,
 	.guest_has_fxsr      = emulator_guest_has_fxsr,
+	.guest_has_rdpid     = emulator_guest_has_rdpid,
 	.set_nmi_mask        = emulator_set_nmi_mask,
 	.get_hflags          = emulator_get_hflags,
 	.exiting_smm         = emulator_exiting_smm,
@@ -7747,7 +7909,7 @@
 }
 EXPORT_SYMBOL_GPL(kvm_skip_emulated_instruction);
 
-static bool kvm_vcpu_check_breakpoint(struct kvm_vcpu *vcpu, int *r)
+static bool kvm_vcpu_check_code_breakpoint(struct kvm_vcpu *vcpu, int *r)
 {
 	if (unlikely(vcpu->guest_debug & KVM_GUESTDBG_USE_HW_BP) &&
 	    (vcpu->arch.guest_debug_dr7 & DR7_BP_EN_MASK)) {
@@ -7816,25 +7978,23 @@
 }
 
 /*
- * Decode to be emulated instruction. Return EMULATION_OK if success.
+ * Decode an instruction for emulation.  The caller is responsible for handling
+ * code breakpoints.  Note, manually detecting code breakpoints is unnecessary
+ * (and wrong) when emulating on an intercepted fault-like exception[*], as
+ * code breakpoints have higher priority and thus have already been done by
+ * hardware.
+ *
+ * [*] Except #MC, which is higher priority, but KVM should never emulate in
+ *     response to a machine check.
  */
 int x86_decode_emulated_instruction(struct kvm_vcpu *vcpu, int emulation_type,
 				    void *insn, int insn_len)
 {
-	int r = EMULATION_OK;
 	struct x86_emulate_ctxt *ctxt = vcpu->arch.emulate_ctxt;
+	int r;
 
 	init_emulate_ctxt(vcpu);
 
-	/*
-	 * We will reenter on the same instruction since we do not set
-	 * complete_userspace_io. This does not handle watchpoints yet,
-	 * those would be handled in the emulate_ops.
-	 */
-	if (!(emulation_type & EMULTYPE_SKIP) &&
-	    kvm_vcpu_check_breakpoint(vcpu, &r))
-		return r;
-
 	r = x86_decode_insn(ctxt, insn, insn_len, emulation_type);
 
 	trace_kvm_emulate_insn_start(vcpu);
@@ -7867,6 +8027,15 @@
 	if (!(emulation_type & EMULTYPE_NO_DECODE)) {
 		kvm_clear_exception_queue(vcpu);
 
+		/*
+		 * Return immediately if RIP hits a code breakpoint, such #DBs
+		 * are fault-like and are higher priority than any faults on
+		 * the code fetch itself.
+		 */
+		if (!(emulation_type & EMULTYPE_SKIP) &&
+		    kvm_vcpu_check_code_breakpoint(vcpu, &r))
+			return r;
+
 		r = x86_decode_emulated_instruction(vcpu, emulation_type,
 						    insn, insn_len);
 		if (r != EMULATION_OK)  {
@@ -7879,7 +8048,9 @@
 						  write_fault_to_spt,
 						  emulation_type))
 				return 1;
-			if (ctxt->have_exception) {
+
+			if (ctxt->have_exception &&
+			    !(emulation_type & EMULTYPE_SKIP)) {
 				/*
 				 * #UD should result in just EMULATION_FAILED, and trap-like
 				 * exception should not be encountered during decode.
@@ -7905,7 +8076,12 @@
 	 * updating interruptibility state and injecting single-step #DBs.
 	 */
 	if (emulation_type & EMULTYPE_SKIP) {
-		kvm_rip_write(vcpu, ctxt->_eip);
+		if (ctxt->mode != X86EMUL_MODE_PROT64)
+			ctxt->eip = (u32)ctxt->_eip;
+		else
+			ctxt->eip = ctxt->_eip;
+
+		kvm_rip_write(vcpu, ctxt->eip);
 		if (ctxt->eflags & X86_EFLAGS_RF)
 			kvm_set_rflags(vcpu, ctxt->eflags & ~X86_EFLAGS_RF);
 		return 1;
@@ -7969,6 +8145,9 @@
 			writeback = false;
 		r = 0;
 		vcpu->arch.complete_userspace_io = complete_emulated_mmio;
+	} else if (vcpu->arch.complete_userspace_io) {
+		writeback = false;
+		r = 0;
 	} else if (r == EMULATION_RESTART)
 		goto restart;
 	else
@@ -7978,6 +8157,12 @@
 		unsigned long rflags = static_call(kvm_x86_get_rflags)(vcpu);
 		toggle_interruptibility(vcpu, ctxt->interruptibility);
 		vcpu->arch.emulate_regs_need_sync_to_vcpu = false;
+
+		/*
+		 * Note, EXCPT_DB is assumed to be fault-like as the emulator
+		 * only supports code breakpoints and general detect #DB, both
+		 * of which are fault-like.
+		 */
 		if (!ctxt->have_exception ||
 		    exception_type(ctxt->exception.vector) == EXCPT_TRAP) {
 			kvm_rip_write(vcpu, ctxt->eip);
@@ -8340,7 +8525,7 @@
 	.is_in_guest		= kvm_is_in_guest,
 	.is_user_mode		= kvm_is_user_mode,
 	.get_guest_ip		= kvm_get_guest_ip,
-	.handle_intel_pt_intr	= kvm_handle_intel_pt_intr,
+	.handle_intel_pt_intr	= NULL,
 };
 
 #ifdef CONFIG_X86_64
@@ -8417,7 +8602,7 @@
 		goto out;
 	}
 	if (ops->disabled_by_bios()) {
-		pr_err_ratelimited("kvm: disabled by bios\n");
+		pr_warn_ratelimited("kvm: disabled by bios\n");
 		r = -EOPNOTSUPP;
 		goto out;
 	}
@@ -8434,18 +8619,11 @@
 	}
 
 	r = -ENOMEM;
-	x86_fpu_cache = kmem_cache_create("x86_fpu", sizeof(struct fpu),
-					  __alignof__(struct fpu), SLAB_ACCOUNT,
-					  NULL);
-	if (!x86_fpu_cache) {
-		printk(KERN_ERR "kvm: failed to allocate cache for x86 fpu\n");
-		goto out;
-	}
 
 	x86_emulator_cache = kvm_alloc_emulator_cache();
 	if (!x86_emulator_cache) {
 		pr_err("kvm: failed to allocate cache for x86 emulator\n");
-		goto out_free_x86_fpu_cache;
+		goto out;
 	}
 
 	user_return_msrs = alloc_percpu(struct kvm_user_return_msrs);
@@ -8455,14 +8633,12 @@
 	}
 	kvm_nr_uret_msrs = 0;
 
-	r = kvm_mmu_module_init();
+	r = kvm_mmu_vendor_module_init();
 	if (r)
 		goto out_free_percpu;
 
 	kvm_timer_init();
 
-	perf_register_guest_info_callbacks(&kvm_guest_cbs);
-
 	if (boot_cpu_has(X86_FEATURE_XSAVE)) {
 		host_xcr0 = xgetbv(XCR_XFEATURE_ENABLED_MASK);
 		supported_xcr0 = host_xcr0 & KVM_SUPPORTED_XCR0;
@@ -8483,8 +8659,6 @@
 	free_percpu(user_return_msrs);
 out_free_x86_emulator_cache:
 	kmem_cache_destroy(x86_emulator_cache);
-out_free_x86_fpu_cache:
-	kmem_cache_destroy(x86_fpu_cache);
 out:
 	return r;
 }
@@ -8496,7 +8670,6 @@
 		clear_hv_tscchange_cb();
 #endif
 	kvm_lapic_exit();
-	perf_unregister_guest_info_callbacks(&kvm_guest_cbs);
 
 	if (!boot_cpu_has(X86_FEATURE_CONSTANT_TSC))
 		cpufreq_unregister_notifier(&kvmclock_cpufreq_notifier_block,
@@ -8508,10 +8681,9 @@
 	cancel_work_sync(&pvclock_gtod_work);
 #endif
 	kvm_x86_ops.hardware_enable = NULL;
-	kvm_mmu_module_exit();
+	kvm_mmu_vendor_module_exit();
 	free_percpu(user_return_msrs);
 	kmem_cache_destroy(x86_emulator_cache);
-	kmem_cache_destroy(x86_fpu_cache);
 #ifdef CONFIG_KVM_XEN
 	static_key_deferred_flush(&kvm_xen_enabled);
 	WARN_ON(static_branch_unlikely(&kvm_xen_enabled.key));
@@ -8567,6 +8739,13 @@
 	if (clock_type != KVM_CLOCK_PAIRING_WALLCLOCK)
 		return -KVM_EOPNOTSUPP;
 
+	/*
+	 * When tsc is in permanent catchup mode guests won't be able to use
+	 * pvclock_read_retry loop to get consistent view of pvclock
+	 */
+	if (vcpu->arch.tsc_always_catchup)
+		return -KVM_EOPNOTSUPP;
+
 	if (!kvm_get_walltime_and_clockread(&ts, &cycle))
 		return -KVM_EOPNOTSUPP;
 
@@ -8592,15 +8771,17 @@
  */
 static void kvm_pv_kick_cpu_op(struct kvm *kvm, unsigned long flags, int apicid)
 {
-	struct kvm_lapic_irq lapic_irq;
-
-	lapic_irq.shorthand = APIC_DEST_NOSHORT;
-	lapic_irq.dest_mode = APIC_DEST_PHYSICAL;
-	lapic_irq.level = 0;
-	lapic_irq.dest_id = apicid;
-	lapic_irq.msi_redir_hint = false;
+	/*
+	 * All other fields are unused for APIC_DM_REMRD, but may be consumed by
+	 * common code, e.g. for tracing. Defer initialization to the compiler.
+	 */
+	struct kvm_lapic_irq lapic_irq = {
+		.delivery_mode = APIC_DM_REMRD,
+		.dest_mode = APIC_DEST_PHYSICAL,
+		.shorthand = APIC_DEST_NOSHORT,
+		.dest_id = apicid,
+	};
 
-	lapic_irq.delivery_mode = APIC_DM_REMRD;
 	kvm_irq_delivery_to_apic(kvm, NULL, &lapic_irq, NULL);
 }
 
@@ -8660,7 +8841,7 @@
 {
 	u64 ret = vcpu->run->hypercall.ret;
 
-	if (!is_64_bit_mode(vcpu))
+	if (!is_64_bit_hypercall(vcpu))
 		ret = (u32)ret;
 	kvm_rax_write(vcpu, ret);
 	++vcpu->stat.hypercalls;
@@ -8686,7 +8867,7 @@
 
 	trace_kvm_hypercall(nr, a0, a1, a2, a3);
 
-	op_64_bit = is_64_bit_mode(vcpu);
+	op_64_bit = is_64_bit_hypercall(vcpu);
 	if (!op_64_bit) {
 		nr &= 0xFFFFFFFF;
 		a0 &= 0xFFFFFFFF;
@@ -8790,14 +8971,7 @@
 {
 	struct kvm_run *kvm_run = vcpu->run;
 
-	/*
-	 * if_flag is obsolete and useless, so do not bother
-	 * setting it for SEV-ES guests.  Userspace can just
-	 * use kvm_run->ready_for_interrupt_injection.
-	 */
-	kvm_run->if_flag = !vcpu->arch.guest_state_protected
-		&& (kvm_get_rflags(vcpu) & X86_EFLAGS_IF) != 0;
-
+	kvm_run->if_flag = static_call(kvm_x86_get_if_flag)(vcpu);
 	kvm_run->cr8 = kvm_get_cr8(vcpu);
 	kvm_run->apic_base = kvm_get_apic_base(vcpu);
 
@@ -8855,8 +9029,20 @@
 
 static void kvm_inject_exception(struct kvm_vcpu *vcpu)
 {
-	if (vcpu->arch.exception.error_code && !is_protmode(vcpu))
-		vcpu->arch.exception.error_code = false;
+	/*
+	 * Suppress the error code if the vCPU is in Real Mode, as Real Mode
+	 * exceptions don't report error codes.  The presence of an error code
+	 * is carried with the exception and only stripped when the exception
+	 * is injected as intercepted #PF VM-Exits for AMD's Paged Real Mode do
+	 * report an error code despite the CPU being in Real Mode.
+	 */
+	vcpu->arch.exception.has_error_code &= is_protmode(vcpu);
+
+	trace_kvm_inj_exception(vcpu->arch.exception.nr,
+				vcpu->arch.exception.has_error_code,
+				vcpu->arch.exception.error_code,
+				vcpu->arch.exception.injected);
+
 	static_call(kvm_x86_queue_exception)(vcpu);
 }
 
@@ -8912,13 +9098,16 @@
 
 	/* try to inject new event if pending */
 	if (vcpu->arch.exception.pending) {
-		trace_kvm_inj_exception(vcpu->arch.exception.nr,
-					vcpu->arch.exception.has_error_code,
-					vcpu->arch.exception.error_code);
-
-		vcpu->arch.exception.pending = false;
-		vcpu->arch.exception.injected = true;
-
+		/*
+		 * Fault-class exceptions, except #DBs, set RF=1 in the RFLAGS
+		 * value pushed on the stack.  Trap-like exception and all #DBs
+		 * leave RF as-is (KVM follows Intel's behavior in this regard;
+		 * AMD states that code breakpoint #DBs excplitly clear RF=0).
+		 *
+		 * Note, most versions of Intel's SDM and AMD's APM incorrectly
+		 * describe the behavior of General Detect #DBs, which are
+		 * fault-like.  They do _not_ set RF, a la code breakpoints.
+		 */
 		if (exception_type(vcpu->arch.exception.nr) == EXCPT_FAULT)
 			__kvm_set_rflags(vcpu, kvm_get_rflags(vcpu) |
 					     X86_EFLAGS_RF);
@@ -8932,6 +9121,10 @@
 		}
 
 		kvm_inject_exception(vcpu);
+
+		vcpu->arch.exception.pending = false;
+		vcpu->arch.exception.injected = true;
+
 		can_inject = false;
 	}
 
@@ -9356,14 +9549,12 @@
 
 	bitmap_zero(vcpu->arch.ioapic_handled_vectors, 256);
 
+	static_call_cond(kvm_x86_sync_pir_to_irr)(vcpu);
+
 	if (irqchip_split(vcpu->kvm))
 		kvm_scan_ioapic_routes(vcpu, vcpu->arch.ioapic_handled_vectors);
-	else {
-		if (vcpu->arch.apicv_active)
-			static_call(kvm_x86_sync_pir_to_irr)(vcpu);
-		if (ioapic_in_kernel(vcpu->kvm))
-			kvm_ioapic_scan_entry(vcpu, vcpu->arch.ioapic_handled_vectors);
-	}
+	else if (ioapic_in_kernel(vcpu->kvm))
+		kvm_ioapic_scan_entry(vcpu, vcpu->arch.ioapic_handled_vectors);
 
 	if (is_guest_mode(vcpu))
 		vcpu->arch.load_eoi_exitmap_pending = true;
@@ -9378,12 +9569,16 @@
 	if (!kvm_apic_hw_enabled(vcpu->arch.apic))
 		return;
 
-	if (to_hv_vcpu(vcpu))
+	if (to_hv_vcpu(vcpu)) {
 		bitmap_or((ulong *)eoi_exit_bitmap,
 			  vcpu->arch.ioapic_handled_vectors,
 			  to_hv_synic(vcpu)->vec_bitmap, 256);
+		static_call(kvm_x86_load_eoi_exitmap)(vcpu, eoi_exit_bitmap);
+		return;
+	}
 
-	static_call(kvm_x86_load_eoi_exitmap)(vcpu, eoi_exit_bitmap);
+	static_call(kvm_x86_load_eoi_exitmap)(
+		vcpu, (u64 *)vcpu->arch.ioapic_handled_vectors);
 }
 
 void kvm_arch_mmu_notifier_invalidate_range(struct kvm *kvm,
@@ -9400,6 +9595,11 @@
 		kvm_make_all_cpus_request(kvm, KVM_REQ_APIC_PAGE_RELOAD);
 }
 
+void kvm_arch_guest_memory_reclaimed(struct kvm *kvm)
+{
+	static_call_cond(kvm_x86_guest_memory_reclaimed)(kvm);
+}
+
 void kvm_vcpu_reload_apic_access_page(struct kvm_vcpu *vcpu)
 {
 	if (!lapic_in_kernel(vcpu))
@@ -9475,10 +9675,7 @@
 			/* Flushing all ASIDs flushes the current ASID... */
 			kvm_clear_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu);
 		}
-		if (kvm_check_request(KVM_REQ_TLB_FLUSH_CURRENT, vcpu))
-			kvm_vcpu_flush_tlb_current(vcpu);
-		if (kvm_check_request(KVM_REQ_TLB_FLUSH_GUEST, vcpu))
-			kvm_vcpu_flush_tlb_guest(vcpu);
+		kvm_service_local_tlb_flush_requests(vcpu);
 
 		if (kvm_check_request(KVM_REQ_REPORT_TPR_ACCESS, vcpu)) {
 			vcpu->run->exit_reason = KVM_EXIT_TPR_ACCESS;
@@ -9629,10 +9826,12 @@
 
 	/*
 	 * This handles the case where a posted interrupt was
-	 * notified with kvm_vcpu_kick.
+	 * notified with kvm_vcpu_kick.  Assigned devices can
+	 * use the POSTED_INTR_VECTOR even if APICv is disabled,
+	 * so do it even if APICv is disabled on this vCPU.
 	 */
-	if (kvm_lapic_enabled(vcpu) && vcpu->arch.apicv_active)
-		static_call(kvm_x86_sync_pir_to_irr)(vcpu);
+	if (kvm_lapic_enabled(vcpu))
+		static_call_cond(kvm_x86_sync_pir_to_irr)(vcpu);
 
 	if (kvm_vcpu_exit_request(vcpu)) {
 		vcpu->mode = OUTSIDE_GUEST_MODE;
@@ -9668,13 +9867,16 @@
 		if (likely(exit_fastpath != EXIT_FASTPATH_REENTER_GUEST))
 			break;
 
-		if (vcpu->arch.apicv_active)
-			static_call(kvm_x86_sync_pir_to_irr)(vcpu);
+		if (kvm_lapic_enabled(vcpu))
+			static_call_cond(kvm_x86_sync_pir_to_irr)(vcpu);
 
 		if (unlikely(kvm_vcpu_exit_request(vcpu))) {
 			exit_fastpath = EXIT_FASTPATH_EXIT_HANDLED;
 			break;
 		}
+
+		/* Note, VM-Exits that go down the "slow" path are accounted below. */
+		++vcpu->stat.exits;
 	}
 
 	/*
@@ -9772,12 +9974,28 @@
 
 static inline int vcpu_block(struct kvm *kvm, struct kvm_vcpu *vcpu)
 {
+	bool hv_timer;
+
 	if (!kvm_arch_vcpu_runnable(vcpu) &&
 	    (!kvm_x86_ops.pre_block || static_call(kvm_x86_pre_block)(vcpu) == 0)) {
+		/*
+		 * Switch to the software timer before halt-polling/blocking as
+		 * the guest's timer may be a break event for the vCPU, and the
+		 * hypervisor timer runs only when the CPU is in guest mode.
+		 * Switch before halt-polling so that KVM recognizes an expired
+		 * timer before blocking.
+		 */
+		hv_timer = kvm_lapic_hv_timer_in_use(vcpu);
+		if (hv_timer)
+			kvm_lapic_switch_to_sw_timer(vcpu);
+
 		srcu_read_unlock(&kvm->srcu, vcpu->srcu_idx);
 		kvm_vcpu_block(vcpu);
 		vcpu->srcu_idx = srcu_read_lock(&kvm->srcu);
 
+		if (hv_timer)
+			kvm_lapic_switch_to_hv_timer(vcpu);
+
 		if (kvm_x86_ops.post_block)
 			static_call(kvm_x86_post_block)(vcpu);
 
@@ -9823,6 +10041,13 @@
 	vcpu->arch.l1tf_flush_l1d = true;
 
 	for (;;) {
+		/*
+		 * If another guest vCPU requests a PV TLB flush in the middle
+		 * of instruction emulation, the rest of the emulation could
+		 * use a stale page translation. Assume that any code after
+		 * this point can start executing an instruction.
+		 */
+		vcpu->arch.at_instruction_boundary = false;
 		if (kvm_vcpu_running(vcpu)) {
 			r = vcpu_enter_guest(vcpu);
 		} else {
@@ -9938,58 +10163,21 @@
 	return 0;
 }
 
-static void kvm_save_current_fpu(struct fpu *fpu)
-{
-	/*
-	 * If the target FPU state is not resident in the CPU registers, just
-	 * memcpy() from current, else save CPU state directly to the target.
-	 */
-	if (test_thread_flag(TIF_NEED_FPU_LOAD))
-		memcpy(&fpu->state, &current->thread.fpu.state,
-		       fpu_kernel_xstate_size);
-	else
-		save_fpregs_to_fpstate(fpu);
-}
-
 /* Swap (qemu) user FPU context for the guest FPU context. */
 static void kvm_load_guest_fpu(struct kvm_vcpu *vcpu)
 {
-	fpregs_lock();
-
-	kvm_save_current_fpu(vcpu->arch.user_fpu);
-
 	/*
-	 * Guests with protected state can't have it set by the hypervisor,
-	 * so skip trying to set it.
+	 * Exclude PKRU from restore as restored separately in
+	 * kvm_x86_ops.run().
 	 */
-	if (vcpu->arch.guest_fpu)
-		/* PKRU is separately restored in kvm_x86_ops.run. */
-		__restore_fpregs_from_fpstate(&vcpu->arch.guest_fpu->state,
-					~XFEATURE_MASK_PKRU);
-
-	fpregs_mark_activate();
-	fpregs_unlock();
-
+	fpu_swap_kvm_fpstate(&vcpu->arch.guest_fpu, true);
 	trace_kvm_fpu(1);
 }
 
 /* When vcpu_run ends, restore user space FPU context. */
 static void kvm_put_guest_fpu(struct kvm_vcpu *vcpu)
 {
-	fpregs_lock();
-
-	/*
-	 * Guests with protected state can't have it read by the hypervisor,
-	 * so skip trying to save it.
-	 */
-	if (vcpu->arch.guest_fpu)
-		kvm_save_current_fpu(vcpu->arch.guest_fpu);
-
-	restore_fpregs_from_fpstate(&vcpu->arch.user_fpu->state);
-
-	fpregs_mark_activate();
-	fpregs_unlock();
-
+	fpu_swap_kvm_fpstate(&vcpu->arch.guest_fpu, false);
 	++vcpu->stat.fpu_reload;
 	trace_kvm_fpu(0);
 }
@@ -10009,6 +10197,11 @@
 			r = -EINTR;
 			goto out;
 		}
+		/*
+		 * It should be impossible for the hypervisor timer to be in
+		 * use before KVM has ever run the vCPU.
+		 */
+		WARN_ON_ONCE(kvm_lapic_hv_timer_in_use(vcpu));
 		kvm_vcpu_block(vcpu);
 		if (kvm_apic_accept_events(vcpu) < 0) {
 			r = 0;
@@ -10341,7 +10534,8 @@
 			return false;
 	}
 
-	return kvm_is_valid_cr4(vcpu, sregs->cr4);
+	return kvm_is_valid_cr4(vcpu, sregs->cr4) &&
+	       kvm_is_valid_cr0(vcpu, sregs->cr0);
 }
 
 static int __set_sregs_common(struct kvm_vcpu *vcpu, struct kvm_sregs *sregs,
@@ -10570,12 +10764,12 @@
 {
 	struct fxregs_state *fxsave;
 
-	if (!vcpu->arch.guest_fpu)
+	if (fpstate_is_confidential(&vcpu->arch.guest_fpu))
 		return 0;
 
 	vcpu_load(vcpu);
 
-	fxsave = &vcpu->arch.guest_fpu->state.fxsave;
+	fxsave = &vcpu->arch.guest_fpu.fpstate->regs.fxsave;
 	memcpy(fpu->fpr, fxsave->st_space, 128);
 	fpu->fcw = fxsave->cwd;
 	fpu->fsw = fxsave->swd;
@@ -10593,12 +10787,12 @@
 {
 	struct fxregs_state *fxsave;
 
-	if (!vcpu->arch.guest_fpu)
+	if (fpstate_is_confidential(&vcpu->arch.guest_fpu))
 		return 0;
 
 	vcpu_load(vcpu);
 
-	fxsave = &vcpu->arch.guest_fpu->state.fxsave;
+	fxsave = &vcpu->arch.guest_fpu.fpstate->regs.fxsave;
 
 	memcpy(fxsave->st_space, fpu->fpr, 128);
 	fxsave->cwd = fpu->fcw;
@@ -10651,14 +10845,6 @@
 
 static void fx_init(struct kvm_vcpu *vcpu)
 {
-	if (!vcpu->arch.guest_fpu)
-		return;
-
-	fpstate_init(&vcpu->arch.guest_fpu->state);
-	if (boot_cpu_has(X86_FEATURE_XSAVES))
-		vcpu->arch.guest_fpu->state.xsave.header.xcomp_bv =
-			host_xcr0 | XSTATE_COMPACTION_ENABLED;
-
 	/*
 	 * Ensure guest xcr0 is valid for loading
 	 */
@@ -10667,15 +10853,6 @@
 	vcpu->arch.cr0 |= X86_CR0_ET;
 }
 
-void kvm_free_guest_fpu(struct kvm_vcpu *vcpu)
-{
-	if (vcpu->arch.guest_fpu) {
-		kmem_cache_free(x86_fpu_cache, vcpu->arch.guest_fpu);
-		vcpu->arch.guest_fpu = NULL;
-	}
-}
-EXPORT_SYMBOL_GPL(kvm_free_guest_fpu);
-
 int kvm_arch_vcpu_precreate(struct kvm *kvm, unsigned int id)
 {
 	if (kvm_check_tsc_unstable() && atomic_read(&kvm->online_vcpus) != 0)
@@ -10707,8 +10884,21 @@
 		r = kvm_create_lapic(vcpu, lapic_timer_advance_ns);
 		if (r < 0)
 			goto fail_mmu_destroy;
-		if (kvm_apicv_activated(vcpu->kvm))
+
+		/*
+		 * Defer evaluating inhibits until the vCPU is first run, as
+		 * this vCPU will not get notified of any changes until this
+		 * vCPU is visible to other vCPUs (marked online and added to
+		 * the set of vCPUs).  Opportunistically mark APICv active as
+		 * VMX in particularly is highly unlikely to have inhibits.
+		 * Ignore the current per-VM APICv state so that vCPU creation
+		 * is guaranteed to run with a deterministic value, the request
+		 * will ensure the vCPU gets the correct state before VM-Entry.
+		 */
+		if (enable_apicv) {
 			vcpu->arch.apicv_active = true;
+			kvm_make_request(KVM_REQ_APICV_UPDATE, vcpu);
+		}
 	} else
 		static_branch_inc(&kvm_has_noapic_vcpu);
 
@@ -10732,19 +10922,11 @@
 	if (!alloc_emulate_ctxt(vcpu))
 		goto free_wbinvd_dirty_mask;
 
-	vcpu->arch.user_fpu = kmem_cache_zalloc(x86_fpu_cache,
-						GFP_KERNEL_ACCOUNT);
-	if (!vcpu->arch.user_fpu) {
-		pr_err("kvm: failed to allocate userspace's fpu\n");
+	if (!fpu_alloc_guest_fpstate(&vcpu->arch.guest_fpu)) {
+		pr_err("kvm: failed to allocate vcpu's fpu\n");
 		goto free_emulate_ctxt;
 	}
 
-	vcpu->arch.guest_fpu = kmem_cache_zalloc(x86_fpu_cache,
-						 GFP_KERNEL_ACCOUNT);
-	if (!vcpu->arch.guest_fpu) {
-		pr_err("kvm: failed to allocate vcpu's fpu\n");
-		goto free_user_fpu;
-	}
 	fx_init(vcpu);
 
 	vcpu->arch.maxphyaddr = cpuid_query_maxphyaddr(vcpu);
@@ -10777,9 +10959,7 @@
 	return 0;
 
 free_guest_fpu:
-	kvm_free_guest_fpu(vcpu);
-free_user_fpu:
-	kmem_cache_free(x86_fpu_cache, vcpu->arch.user_fpu);
+	fpu_free_guest_fpstate(&vcpu->arch.guest_fpu);
 free_emulate_ctxt:
 	kmem_cache_free(x86_emulator_cache, vcpu->arch.emulate_ctxt);
 free_wbinvd_dirty_mask:
@@ -10817,19 +10997,15 @@
 
 void kvm_arch_vcpu_destroy(struct kvm_vcpu *vcpu)
 {
-	struct gfn_to_pfn_cache *cache = &vcpu->arch.st.cache;
 	int idx;
 
-	kvm_release_pfn(cache->pfn, cache->dirty, cache);
-
 	kvmclock_reset(vcpu);
 
 	static_call(kvm_x86_vcpu_free)(vcpu);
 
 	kmem_cache_free(x86_emulator_cache, vcpu->arch.emulate_ctxt);
 	free_cpumask_var(vcpu->arch.wbinvd_dirty_mask);
-	kmem_cache_free(x86_fpu_cache, vcpu->arch.user_fpu);
-	kvm_free_guest_fpu(vcpu);
+	fpu_free_guest_fpstate(&vcpu->arch.guest_fpu);
 
 	kvm_hv_vcpu_uninit(vcpu);
 	kvm_pmu_destroy(vcpu);
@@ -10850,8 +11026,18 @@
 	unsigned long new_cr0;
 	u32 eax, dummy;
 
+	/*
+	 * SVM doesn't unconditionally VM-Exit on INIT and SHUTDOWN, thus it's
+	 * possible to INIT the vCPU while L2 is active.  Force the vCPU back
+	 * into L1 as EFER.SVME is cleared on INIT (along with all other EFER
+	 * bits), i.e. virtualization is disabled.
+	 */
+	if (is_guest_mode(vcpu))
+		kvm_leave_nested(vcpu);
+
 	kvm_lapic_reset(vcpu, init_event);
 
+	WARN_ON_ONCE(is_guest_mode(vcpu) || is_smm(vcpu));
 	vcpu->arch.hflags = 0;
 
 	vcpu->arch.smi_pending = 0;
@@ -10881,8 +11067,8 @@
 	kvm_async_pf_hash_reset(vcpu);
 	vcpu->arch.apf.halted = false;
 
-	if (vcpu->arch.guest_fpu && kvm_mpx_supported()) {
-		void *mpx_state_buffer;
+	if (vcpu->arch.guest_fpu.fpstate && kvm_mpx_supported()) {
+		struct fpstate *fpstate = vcpu->arch.guest_fpu.fpstate;
 
 		/*
 		 * To avoid have the INIT path from kvm_apic_has_events() that be
@@ -10890,14 +11076,10 @@
 		 */
 		if (init_event)
 			kvm_put_guest_fpu(vcpu);
-		mpx_state_buffer = get_xsave_addr(&vcpu->arch.guest_fpu->state.xsave,
-					XFEATURE_BNDREGS);
-		if (mpx_state_buffer)
-			memset(mpx_state_buffer, 0, sizeof(struct mpx_bndreg_state));
-		mpx_state_buffer = get_xsave_addr(&vcpu->arch.guest_fpu->state.xsave,
-					XFEATURE_BNDCSR);
-		if (mpx_state_buffer)
-			memset(mpx_state_buffer, 0, sizeof(struct mpx_bndcsr));
+
+		fpstate_clear_xstate_component(fpstate, XFEATURE_BNDREGS);
+		fpstate_clear_xstate_component(fpstate, XFEATURE_BNDCSR);
+
 		if (init_event)
 			kvm_load_guest_fpu(vcpu);
 	}
@@ -10908,7 +11090,8 @@
 
 		vcpu->arch.msr_misc_features_enables = 0;
 
-		vcpu->arch.xcr0 = XFEATURE_MASK_FP;
+		__kvm_set_xcr(vcpu, 0, XFEATURE_MASK_FP);
+		__kvm_set_msr(vcpu, MSR_IA32_XSS, 0, true);
 	}
 
 	memset(vcpu->arch.regs, 0, sizeof(vcpu->arch.regs));
@@ -10927,8 +11110,6 @@
 		eax = 0x600;
 	kvm_rdx_write(vcpu, eax);
 
-	vcpu->arch.ia32_xss = 0;
-
 	static_call(kvm_x86_vcpu_reset)(vcpu, init_event);
 
 	kvm_set_rflags(vcpu, X86_EFLAGS_FIXED);
@@ -11104,6 +11285,10 @@
 	memcpy(&kvm_x86_ops, ops->runtime_ops, sizeof(kvm_x86_ops));
 	kvm_ops_static_call_update();
 
+	if (ops->intel_pt_intr_in_guest && ops->intel_pt_intr_in_guest())
+		kvm_guest_cbs.handle_intel_pt_intr = kvm_handle_intel_pt_intr;
+	perf_register_guest_info_callbacks(&kvm_guest_cbs);
+
 	if (!kvm_cpu_cap_has(X86_FEATURE_XSAVES))
 		supported_xss = 0;
 
@@ -11131,6 +11316,9 @@
 
 void kvm_arch_hardware_unsetup(void)
 {
+	perf_unregister_guest_info_callbacks(&kvm_guest_cbs);
+	kvm_guest_cbs.handle_intel_pt_intr = NULL;
+
 	static_call(kvm_x86_hardware_unsetup)();
 }
 
@@ -11177,7 +11365,7 @@
 void kvm_arch_free_vm(struct kvm *kvm)
 {
 	kfree(to_kvm_hv(kvm)->hv_pa_pg);
-	vfree(kvm);
+	__kvm_arch_free_vm(kvm);
 }
 
 
@@ -11420,7 +11608,7 @@
 		if (slot->arch.rmap[i])
 			continue;
 
-		slot->arch.rmap[i] = kvcalloc(lpages, sz, GFP_KERNEL_ACCOUNT);
+		slot->arch.rmap[i] = __vcalloc(lpages, sz, GFP_KERNEL_ACCOUNT);
 		if (!slot->arch.rmap[i]) {
 			memslot_rmap_free(slot);
 			return -ENOMEM;
@@ -11501,7 +11689,7 @@
 
 		lpages = __kvm_mmu_slot_lpages(slot, npages, level);
 
-		linfo = kvcalloc(lpages, sizeof(*linfo), GFP_KERNEL_ACCOUNT);
+		linfo = __vcalloc(lpages, sizeof(*linfo), GFP_KERNEL_ACCOUNT);
 		if (!linfo)
 			goto out_free;
 
@@ -12045,9 +12233,9 @@
 }
 EXPORT_SYMBOL_GPL(kvm_arch_end_assignment);
 
-bool kvm_arch_has_assigned_device(struct kvm *kvm)
+bool noinstr kvm_arch_has_assigned_device(struct kvm *kvm)
 {
-	return atomic_read(&kvm->arch.assigned_device_count);
+	return arch_atomic_read(&kvm->arch.assigned_device_count);
 }
 EXPORT_SYMBOL_GPL(kvm_arch_has_assigned_device);
 
@@ -12509,3 +12697,22 @@
 EXPORT_TRACEPOINT_SYMBOL_GPL(kvm_vmgexit_exit);
 EXPORT_TRACEPOINT_SYMBOL_GPL(kvm_vmgexit_msr_protocol_enter);
 EXPORT_TRACEPOINT_SYMBOL_GPL(kvm_vmgexit_msr_protocol_exit);
+
+static int __init kvm_x86_init(void)
+{
+	kvm_init_xstate_sizes();
+
+	kvm_mmu_x86_module_init();
+	mitigate_smt_rsb &= boot_cpu_has_bug(X86_BUG_SMT_RSB) && cpu_smt_possible();
+	return 0;
+}
+module_init(kvm_x86_init);
+
+static void __exit kvm_x86_exit(void)
+{
+	/*
+	 * If module_init() is implemented, module_exit() must also be
+	 * implemented to allow module unload.
+	 */
+}
+module_exit(kvm_x86_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/x86.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/x86.h
@@ -26,7 +26,7 @@
 	 */
 	instrumentation_begin();
 	trace_hardirqs_on_prepare();
-	lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+	lockdep_hardirqs_on_prepare();
 	instrumentation_end();
 
 	guest_enter_irqoff();
@@ -103,6 +103,7 @@
 
 #define MSR_IA32_CR_PAT_DEFAULT  0x0007040600070406ULL
 
+void kvm_service_local_tlb_flush_requests(struct kvm_vcpu *vcpu);
 int kvm_check_nested_events(struct kvm_vcpu *vcpu);
 
 static inline void kvm_clear_exception_queue(struct kvm_vcpu *vcpu)
@@ -153,12 +154,24 @@
 {
 	int cs_db, cs_l;
 
+	WARN_ON_ONCE(vcpu->arch.guest_state_protected);
+
 	if (!is_long_mode(vcpu))
 		return false;
 	static_call(kvm_x86_get_cs_db_l_bits)(vcpu, &cs_db, &cs_l);
 	return cs_l;
 }
 
+static inline bool is_64_bit_hypercall(struct kvm_vcpu *vcpu)
+{
+	/*
+	 * If running with protected guest state, the CS register is not
+	 * accessible. The hypercall register values will have had to been
+	 * provided in 64-bit mode, so assume the guest is in 64-bit.
+	 */
+	return vcpu->arch.guest_state_protected || is_64_bit_mode(vcpu);
+}
+
 static inline bool x86_exception_has_error_code(unsigned int vector)
 {
 	static u32 exception_has_error_code = BIT(DF_VECTOR) | BIT(TS_VECTOR) |
@@ -173,12 +186,6 @@
 	return vcpu->arch.walk_mmu == &vcpu->arch.nested_mmu;
 }
 
-static inline void kvm_vcpu_flush_tlb_current(struct kvm_vcpu *vcpu)
-{
-	++vcpu->stat.tlb_flush;
-	static_call(kvm_x86_tlb_flush_current)(vcpu);
-}
-
 static inline int is_pae(struct kvm_vcpu *vcpu)
 {
 	return kvm_read_cr4_bits(vcpu, X86_CR4_PAE);
@@ -204,14 +211,9 @@
 	return kvm_read_cr4_bits(vcpu, X86_CR4_LA57) ? 57 : 48;
 }
 
-static inline u64 get_canonical(u64 la, u8 vaddr_bits)
-{
-	return ((int64_t)la << (64 - vaddr_bits)) >> (64 - vaddr_bits);
-}
-
 static inline bool is_noncanonical_address(u64 la, struct kvm_vcpu *vcpu)
 {
-	return get_canonical(la, vcpu_virt_addr_bits(vcpu)) != la;
+	return !__is_canonical_address(la, vcpu_virt_addr_bits(vcpu));
 }
 
 static inline void vcpu_cache_mmio_info(struct kvm_vcpu *vcpu,
@@ -441,7 +443,7 @@
 void kvm_load_guest_xsave_state(struct kvm_vcpu *vcpu);
 void kvm_load_host_xsave_state(struct kvm_vcpu *vcpu);
 int kvm_spec_ctrl_test_value(u64 value);
-bool kvm_is_valid_cr4(struct kvm_vcpu *vcpu, unsigned long cr4);
+bool __kvm_is_valid_cr4(struct kvm_vcpu *vcpu, unsigned long cr4);
 int kvm_handle_memory_failure(struct kvm_vcpu *vcpu, int r,
 			      struct x86_exception *e);
 int kvm_handle_invpcid(struct kvm_vcpu *vcpu, unsigned long type, gva_t gva);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/xen.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/xen.c
@@ -93,32 +93,57 @@
 void kvm_xen_update_runstate_guest(struct kvm_vcpu *v, int state)
 {
 	struct kvm_vcpu_xen *vx = &v->arch.xen;
+	struct gfn_to_hva_cache *ghc = &vx->runstate_cache;
+	struct kvm_memslots *slots = kvm_memslots(v->kvm);
+	bool atomic = (state == RUNSTATE_runnable);
 	uint64_t state_entry_time;
-	unsigned int offset;
+	int __user *user_state;
+	uint64_t __user *user_times;
 
 	kvm_xen_update_runstate(v, state);
 
 	if (!vx->runstate_set)
 		return;
 
-	BUILD_BUG_ON(sizeof(struct compat_vcpu_runstate_info) != 0x2c);
+	if (unlikely(slots->generation != ghc->generation || kvm_is_error_hva(ghc->hva)) &&
+	    kvm_gfn_to_hva_cache_init(v->kvm, ghc, ghc->gpa, ghc->len))
+		return;
+
+	/* We made sure it fits in a single page */
+	BUG_ON(!ghc->memslot);
+
+	if (atomic)
+		pagefault_disable();
 
-	offset = offsetof(struct compat_vcpu_runstate_info, state_entry_time);
-#ifdef CONFIG_X86_64
 	/*
-	 * The only difference is alignment of uint64_t in 32-bit.
-	 * So the first field 'state' is accessed directly using
-	 * offsetof() (where its offset happens to be zero), while the
-	 * remaining fields which are all uint64_t, start at 'offset'
-	 * which we tweak here by adding 4.
+	 * The only difference between 32-bit and 64-bit versions of the
+	 * runstate struct us the alignment of uint64_t in 32-bit, which
+	 * means that the 64-bit version has an additional 4 bytes of
+	 * padding after the first field 'state'.
+	 *
+	 * So we use 'int __user *user_state' to point to the state field,
+	 * and 'uint64_t __user *user_times' for runstate_entry_time. So
+	 * the actual array of time[] in each state starts at user_times[1].
 	 */
+	BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, state) != 0);
+	BUILD_BUG_ON(offsetof(struct compat_vcpu_runstate_info, state) != 0);
+	user_state = (int __user *)ghc->hva;
+
+	BUILD_BUG_ON(sizeof(struct compat_vcpu_runstate_info) != 0x2c);
+
+	user_times = (uint64_t __user *)(ghc->hva +
+					 offsetof(struct compat_vcpu_runstate_info,
+						  state_entry_time));
+#ifdef CONFIG_X86_64
 	BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, state_entry_time) !=
 		     offsetof(struct compat_vcpu_runstate_info, state_entry_time) + 4);
 	BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, time) !=
 		     offsetof(struct compat_vcpu_runstate_info, time) + 4);
 
 	if (v->kvm->arch.xen.long_mode)
-		offset = offsetof(struct vcpu_runstate_info, state_entry_time);
+		user_times = (uint64_t __user *)(ghc->hva +
+						 offsetof(struct vcpu_runstate_info,
+							  state_entry_time));
 #endif
 	/*
 	 * First write the updated state_entry_time at the appropriate
@@ -132,10 +157,8 @@
 	BUILD_BUG_ON(sizeof(((struct compat_vcpu_runstate_info *)0)->state_entry_time) !=
 		     sizeof(state_entry_time));
 
-	if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache,
-					  &state_entry_time, offset,
-					  sizeof(state_entry_time)))
-		return;
+	if (__put_user(state_entry_time, user_times))
+		goto out;
 	smp_wmb();
 
 	/*
@@ -149,11 +172,8 @@
 	BUILD_BUG_ON(sizeof(((struct compat_vcpu_runstate_info *)0)->state) !=
 		     sizeof(vx->current_runstate));
 
-	if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache,
-					  &vx->current_runstate,
-					  offsetof(struct vcpu_runstate_info, state),
-					  sizeof(vx->current_runstate)))
-		return;
+	if (__put_user(vx->current_runstate, user_state))
+		goto out;
 
 	/*
 	 * Write the actual runstate times immediately after the
@@ -168,24 +188,23 @@
 	BUILD_BUG_ON(sizeof(((struct vcpu_runstate_info *)0)->time) !=
 		     sizeof(vx->runstate_times));
 
-	if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache,
-					  &vx->runstate_times[0],
-					  offset + sizeof(u64),
-					  sizeof(vx->runstate_times)))
-		return;
-
+	if (__copy_to_user(user_times + 1, vx->runstate_times, sizeof(vx->runstate_times)))
+		goto out;
 	smp_wmb();
 
 	/*
 	 * Finally, clear the XEN_RUNSTATE_UPDATE bit in the guest's
 	 * runstate_entry_time field.
 	 */
-
 	state_entry_time &= ~XEN_RUNSTATE_UPDATE;
-	if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache,
-					  &state_entry_time, offset,
-					  sizeof(state_entry_time)))
-		return;
+	__put_user(state_entry_time, user_times);
+	smp_wmb();
+
+ out:
+	mark_page_dirty_in_slot(v->kvm, ghc->memslot, ghc->gpa >> PAGE_SHIFT);
+
+	if (atomic)
+		pagefault_enable();
 }
 
 int __kvm_xen_has_interrupt(struct kvm_vcpu *v)
@@ -299,7 +318,7 @@
 		break;
 
 	case KVM_XEN_ATTR_TYPE_SHARED_INFO:
-		data->u.shared_info.gfn = gpa_to_gfn(kvm->arch.xen.shinfo_gfn);
+		data->u.shared_info.gfn = kvm->arch.xen.shinfo_gfn;
 		r = 0;
 		break;
 
@@ -337,6 +356,12 @@
 			break;
 		}
 
+		/* It must fit within a single page */
+		if ((data->u.gpa & ~PAGE_MASK) + sizeof(struct vcpu_info) > PAGE_SIZE) {
+			r = -EINVAL;
+			break;
+		}
+
 		r = kvm_gfn_to_hva_cache_init(vcpu->kvm,
 					      &vcpu->arch.xen.vcpu_info_cache,
 					      data->u.gpa,
@@ -354,6 +379,12 @@
 			break;
 		}
 
+		/* It must fit within a single page */
+		if ((data->u.gpa & ~PAGE_MASK) + sizeof(struct pvclock_vcpu_time_info) > PAGE_SIZE) {
+			r = -EINVAL;
+			break;
+		}
+
 		r = kvm_gfn_to_hva_cache_init(vcpu->kvm,
 					      &vcpu->arch.xen.vcpu_time_info_cache,
 					      data->u.gpa,
@@ -375,6 +406,12 @@
 			break;
 		}
 
+		/* It must fit within a single page */
+		if ((data->u.gpa & ~PAGE_MASK) + sizeof(struct vcpu_runstate_info) > PAGE_SIZE) {
+			r = -EINVAL;
+			break;
+		}
+
 		r = kvm_gfn_to_hva_cache_init(vcpu->kvm,
 					      &vcpu->arch.xen.runstate_cache,
 					      data->u.gpa,
@@ -698,7 +735,7 @@
 	    kvm_hv_hypercall_enabled(vcpu))
 		return kvm_hv_hypercall(vcpu);
 
-	longmode = is_64_bit_mode(vcpu);
+	longmode = is_64_bit_hypercall(vcpu);
 	if (!longmode) {
 		params[0] = (u32)kvm_rbx_read(vcpu);
 		params[1] = (u32)kvm_rcx_read(vcpu);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/kvm/xen.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/kvm/xen.h
@@ -97,8 +97,10 @@
 	 * behalf of the vCPU. Only if the VMM does actually block
 	 * does it need to enter RUNSTATE_blocked.
 	 */
-	if (vcpu->preempted)
-		kvm_xen_update_runstate_guest(vcpu, RUNSTATE_runnable);
+	if (WARN_ON_ONCE(!vcpu->preempted))
+		return;
+
+	kvm_xen_update_runstate_guest(vcpu, RUNSTATE_runnable);
 }
 
 /* 32-bit compatibility definitions, also used natively in 32-bit build */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/atomic64_386_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/atomic64_386_32.S
@@ -9,81 +9,83 @@
 #include <asm/alternative.h>
 
 /* if you want SMP support, implement these with real spinlocks */
-.macro LOCK reg
+.macro IRQ_SAVE reg
 	pushfl
 	cli
 .endm
 
-.macro UNLOCK reg
+.macro IRQ_RESTORE reg
 	popfl
 .endm
 
-#define BEGIN(op) \
+#define BEGIN_IRQ_SAVE(op) \
 .macro endp; \
 SYM_FUNC_END(atomic64_##op##_386); \
 .purgem endp; \
 .endm; \
 SYM_FUNC_START(atomic64_##op##_386); \
-	LOCK v;
+	IRQ_SAVE v;
 
 #define ENDP endp
 
-#define RET \
-	UNLOCK v; \
-	ret
-
-#define RET_ENDP \
-	RET; \
-	ENDP
+#define RET_IRQ_RESTORE \
+	IRQ_RESTORE v; \
+	RET
 
 #define v %ecx
-BEGIN(read)
+BEGIN_IRQ_SAVE(read)
 	movl  (v), %eax
 	movl 4(v), %edx
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %esi
-BEGIN(set)
+BEGIN_IRQ_SAVE(set)
 	movl %ebx,  (v)
 	movl %ecx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v  %esi
-BEGIN(xchg)
+BEGIN_IRQ_SAVE(xchg)
 	movl  (v), %eax
 	movl 4(v), %edx
 	movl %ebx,  (v)
 	movl %ecx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %ecx
-BEGIN(add)
+BEGIN_IRQ_SAVE(add)
 	addl %eax,  (v)
 	adcl %edx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %ecx
-BEGIN(add_return)
+BEGIN_IRQ_SAVE(add_return)
 	addl  (v), %eax
 	adcl 4(v), %edx
 	movl %eax,  (v)
 	movl %edx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %ecx
-BEGIN(sub)
+BEGIN_IRQ_SAVE(sub)
 	subl %eax,  (v)
 	sbbl %edx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %ecx
-BEGIN(sub_return)
+BEGIN_IRQ_SAVE(sub_return)
 	negl %edx
 	negl %eax
 	sbbl $0, %edx
@@ -91,47 +93,52 @@
 	adcl 4(v), %edx
 	movl %eax,  (v)
 	movl %edx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %esi
-BEGIN(inc)
+BEGIN_IRQ_SAVE(inc)
 	addl $1,  (v)
 	adcl $0, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %esi
-BEGIN(inc_return)
+BEGIN_IRQ_SAVE(inc_return)
 	movl  (v), %eax
 	movl 4(v), %edx
 	addl $1, %eax
 	adcl $0, %edx
 	movl %eax,  (v)
 	movl %edx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %esi
-BEGIN(dec)
+BEGIN_IRQ_SAVE(dec)
 	subl $1,  (v)
 	sbbl $0, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %esi
-BEGIN(dec_return)
+BEGIN_IRQ_SAVE(dec_return)
 	movl  (v), %eax
 	movl 4(v), %edx
 	subl $1, %eax
 	sbbl $0, %edx
 	movl %eax,  (v)
 	movl %edx, 4(v)
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
 
 #define v %esi
-BEGIN(add_unless)
+BEGIN_IRQ_SAVE(add_unless)
 	addl %eax, %ecx
 	adcl %edx, %edi
 	addl  (v), %eax
@@ -143,7 +150,7 @@
 	movl %edx, 4(v)
 	movl $1, %eax
 2:
-	RET
+	RET_IRQ_RESTORE
 3:
 	cmpl %edx, %edi
 	jne 1b
@@ -153,7 +160,7 @@
 #undef v
 
 #define v %esi
-BEGIN(inc_not_zero)
+BEGIN_IRQ_SAVE(inc_not_zero)
 	movl  (v), %eax
 	movl 4(v), %edx
 	testl %eax, %eax
@@ -165,7 +172,7 @@
 	movl %edx, 4(v)
 	movl $1, %eax
 2:
-	RET
+	RET_IRQ_RESTORE
 3:
 	testl %edx, %edx
 	jne 1b
@@ -174,7 +181,7 @@
 #undef v
 
 #define v %esi
-BEGIN(dec_if_positive)
+BEGIN_IRQ_SAVE(dec_if_positive)
 	movl  (v), %eax
 	movl 4(v), %edx
 	subl $1, %eax
@@ -183,5 +190,6 @@
 	movl %eax,  (v)
 	movl %edx, 4(v)
 1:
-RET_ENDP
+	RET_IRQ_RESTORE
+ENDP
 #undef v
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/atomic64_cx8_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/atomic64_cx8_32.S
@@ -18,7 +18,7 @@
 
 SYM_FUNC_START(atomic64_read_cx8)
 	read64 %ecx
-	ret
+	RET
 SYM_FUNC_END(atomic64_read_cx8)
 
 SYM_FUNC_START(atomic64_set_cx8)
@@ -28,7 +28,7 @@
 	cmpxchg8b (%esi)
 	jne 1b
 
-	ret
+	RET
 SYM_FUNC_END(atomic64_set_cx8)
 
 SYM_FUNC_START(atomic64_xchg_cx8)
@@ -37,7 +37,7 @@
 	cmpxchg8b (%esi)
 	jne 1b
 
-	ret
+	RET
 SYM_FUNC_END(atomic64_xchg_cx8)
 
 .macro addsub_return func ins insc
@@ -68,7 +68,7 @@
 	popl %esi
 	popl %ebx
 	popl %ebp
-	ret
+	RET
 SYM_FUNC_END(atomic64_\func\()_return_cx8)
 .endm
 
@@ -93,7 +93,7 @@
 	movl %ebx, %eax
 	movl %ecx, %edx
 	popl %ebx
-	ret
+	RET
 SYM_FUNC_END(atomic64_\func\()_return_cx8)
 .endm
 
@@ -118,7 +118,7 @@
 	movl %ebx, %eax
 	movl %ecx, %edx
 	popl %ebx
-	ret
+	RET
 SYM_FUNC_END(atomic64_dec_if_positive_cx8)
 
 SYM_FUNC_START(atomic64_add_unless_cx8)
@@ -149,7 +149,7 @@
 	addl $8, %esp
 	popl %ebx
 	popl %ebp
-	ret
+	RET
 4:
 	cmpl %edx, 4(%esp)
 	jne 2b
@@ -176,5 +176,5 @@
 	movl $1, %eax
 3:
 	popl %ebx
-	ret
+	RET
 SYM_FUNC_END(atomic64_inc_not_zero_cx8)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/checksum_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/checksum_32.S
@@ -127,7 +127,7 @@
 8:
 	popl %ebx
 	popl %esi
-	ret
+	RET
 SYM_FUNC_END(csum_partial)
 
 #else
@@ -245,7 +245,7 @@
 90: 
 	popl %ebx
 	popl %esi
-	ret
+	RET
 SYM_FUNC_END(csum_partial)
 				
 #endif
@@ -371,7 +371,7 @@
 	popl %esi
 	popl %edi
 	popl %ecx			# equivalent to addl $4,%esp
-	ret	
+	RET
 SYM_FUNC_END(csum_partial_copy_generic)
 
 #else
@@ -447,7 +447,7 @@
 	popl %esi
 	popl %edi
 	popl %ebx
-	ret
+	RET
 SYM_FUNC_END(csum_partial_copy_generic)
 				
 #undef ROUND
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/clear_page_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/clear_page_64.S
@@ -17,7 +17,7 @@
 	movl $4096/8,%ecx
 	xorl %eax,%eax
 	rep stosq
-	ret
+	RET
 SYM_FUNC_END(clear_page_rep)
 EXPORT_SYMBOL_GPL(clear_page_rep)
 
@@ -39,7 +39,7 @@
 	leaq	64(%rdi),%rdi
 	jnz	.Lloop
 	nop
-	ret
+	RET
 SYM_FUNC_END(clear_page_orig)
 EXPORT_SYMBOL_GPL(clear_page_orig)
 
@@ -47,6 +47,6 @@
 	movl $4096,%ecx
 	xorl %eax,%eax
 	rep stosb
-	ret
+	RET
 SYM_FUNC_END(clear_page_erms)
 EXPORT_SYMBOL_GPL(clear_page_erms)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/cmpxchg16b_emu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/cmpxchg16b_emu.S
@@ -37,11 +37,11 @@
 
 	popfq
 	mov $1, %al
-	ret
+	RET
 
 .Lnot_same:
 	popfq
 	xor %al,%al
-	ret
+	RET
 
 SYM_FUNC_END(this_cpu_cmpxchg16b_emu)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/cmpxchg8b_emu.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/cmpxchg8b_emu.S
@@ -32,7 +32,7 @@
 	movl %ecx, 4(%esi)
 
 	popfl
-	ret
+	RET
 
 .Lnot_same:
 	movl  (%esi), %eax
@@ -40,7 +40,7 @@
 	movl 4(%esi), %edx
 
 	popfl
-	ret
+	RET
 
 SYM_FUNC_END(cmpxchg8b_emu)
 EXPORT_SYMBOL(cmpxchg8b_emu)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/copy_mc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/copy_mc.c
@@ -70,23 +70,23 @@
 }
 EXPORT_SYMBOL_GPL(copy_mc_to_kernel);
 
-unsigned long __must_check copy_mc_to_user(void *dst, const void *src, unsigned len)
+unsigned long __must_check copy_mc_to_user(void __user *dst, const void *src, unsigned len)
 {
 	unsigned long ret;
 
 	if (copy_mc_fragile_enabled) {
 		__uaccess_begin();
-		ret = copy_mc_fragile(dst, src, len);
+		ret = copy_mc_fragile((__force void *)dst, src, len);
 		__uaccess_end();
 		return ret;
 	}
 
 	if (static_cpu_has(X86_FEATURE_ERMS)) {
 		__uaccess_begin();
-		ret = copy_mc_enhanced_fast_string(dst, src, len);
+		ret = copy_mc_enhanced_fast_string((__force void *)dst, src, len);
 		__uaccess_end();
 		return ret;
 	}
 
-	return copy_user_generic(dst, src, len);
+	return copy_user_generic((__force void *)dst, src, len);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/copy_mc_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/copy_mc_64.S
@@ -77,7 +77,7 @@
 .L_done_memcpy_trap:
 	xorl %eax, %eax
 .L_done:
-	ret
+	RET
 SYM_FUNC_END(copy_mc_fragile)
 
 	.section .fixup, "ax"
@@ -107,9 +107,9 @@
 
 	.previous
 
-	_ASM_EXTABLE_FAULT(.L_read_leading_bytes, .E_leading_bytes)
-	_ASM_EXTABLE_FAULT(.L_read_words, .E_read_words)
-	_ASM_EXTABLE_FAULT(.L_read_trailing_bytes, .E_trailing_bytes)
+	_ASM_EXTABLE_TYPE(.L_read_leading_bytes, .E_leading_bytes, EX_TYPE_DEFAULT_MCE_SAFE)
+	_ASM_EXTABLE_TYPE(.L_read_words, .E_read_words, EX_TYPE_DEFAULT_MCE_SAFE)
+	_ASM_EXTABLE_TYPE(.L_read_trailing_bytes, .E_trailing_bytes, EX_TYPE_DEFAULT_MCE_SAFE)
 	_ASM_EXTABLE(.L_write_leading_bytes, .E_leading_bytes)
 	_ASM_EXTABLE(.L_write_words, .E_write_words)
 	_ASM_EXTABLE(.L_write_trailing_bytes, .E_trailing_bytes)
@@ -132,7 +132,7 @@
 	rep movsb
 	/* Copy successful. Return zero */
 	xorl %eax, %eax
-	ret
+	RET
 SYM_FUNC_END(copy_mc_enhanced_fast_string)
 
 	.section .fixup, "ax"
@@ -145,9 +145,9 @@
 	 * user-copy routines.
 	 */
 	movq %rcx, %rax
-	ret
+	RET
 
 	.previous
 
-	_ASM_EXTABLE_FAULT(.L_copy, .E_copy)
+	_ASM_EXTABLE_TYPE(.L_copy, .E_copy, EX_TYPE_DEFAULT_MCE_SAFE)
 #endif /* !CONFIG_UML */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/copy_page_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/copy_page_64.S
@@ -17,7 +17,7 @@
 	ALTERNATIVE "jmp copy_page_regs", "", X86_FEATURE_REP_GOOD
 	movl	$4096/8, %ecx
 	rep	movsq
-	ret
+	RET
 SYM_FUNC_END(copy_page)
 EXPORT_SYMBOL(copy_page)
 
@@ -85,5 +85,5 @@
 	movq	(%rsp), %rbx
 	movq	1*8(%rsp), %r12
 	addq	$2*8, %rsp
-	ret
+	RET
 SYM_FUNC_END(copy_page_regs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/copy_user_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/copy_user_64.S
@@ -105,7 +105,7 @@
 	jnz 21b
 23:	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 
 	.section .fixup,"ax"
 30:	shll $6,%ecx
@@ -173,7 +173,7 @@
 	movsb
 	xorl %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 
 	.section .fixup,"ax"
 11:	leal (%rdx,%rcx,8),%ecx
@@ -207,7 +207,7 @@
 	movsb
 	xorl %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 
 	.section .fixup,"ax"
 12:	movl %ecx,%edx		/* ecx is zerorest also */
@@ -239,7 +239,7 @@
 1:	rep movsb
 2:	mov %ecx,%eax
 	ASM_CLAC
-	ret
+	RET
 
 	/*
 	 * Return zero to pretend that this copy succeeded. This
@@ -250,7 +250,7 @@
 	 */
 3:	xorl %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 
 	_ASM_EXTABLE_CPY(1b, 2b)
 SYM_CODE_END(.Lcopy_user_handle_tail)
@@ -361,7 +361,7 @@
 	xorl %eax,%eax
 	ASM_CLAC
 	sfence
-	ret
+	RET
 
 	.section .fixup,"ax"
 .L_fixup_4x8b_copy:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/csum-copy_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/csum-copy_64.S
@@ -201,7 +201,7 @@
 	movq 3*8(%rsp), %r13
 	movq 4*8(%rsp), %r15
 	addq $5*8, %rsp
-	ret
+	RET
 .Lshort:
 	movl %ecx, %r10d
 	jmp  .L1
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/delay.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/delay.c
@@ -54,8 +54,8 @@
 		"	jnz 2b		\n"
 		"3:	dec %0		\n"
 
-		: /* we don't need output */
-		:"a" (loops)
+		: "+a" (loops)
+		:
 	);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/error-inject.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/error-inject.c
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 
+#include <linux/linkage.h>
 #include <linux/error-injection.h>
 #include <linux/kprobes.h>
 
@@ -10,7 +11,7 @@
 	".type just_return_func, @function\n"
 	".globl just_return_func\n"
 	"just_return_func:\n"
-	"	ret\n"
+		ASM_RET
 	".size just_return_func, .-just_return_func\n"
 );
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/getuser.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/getuser.S
@@ -57,7 +57,7 @@
 1:	movzbl (%_ASM_AX),%edx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_1)
 EXPORT_SYMBOL(__get_user_1)
 
@@ -71,7 +71,7 @@
 2:	movzwl (%_ASM_AX),%edx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_2)
 EXPORT_SYMBOL(__get_user_2)
 
@@ -85,7 +85,7 @@
 3:	movl (%_ASM_AX),%edx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_4)
 EXPORT_SYMBOL(__get_user_4)
 
@@ -100,7 +100,7 @@
 4:	movq (%_ASM_AX),%rdx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 #else
 	LOAD_TASK_SIZE_MINUS_N(7)
 	cmp %_ASM_DX,%_ASM_AX
@@ -112,7 +112,7 @@
 5:	movl 4(%_ASM_AX),%ecx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 #endif
 SYM_FUNC_END(__get_user_8)
 EXPORT_SYMBOL(__get_user_8)
@@ -124,7 +124,7 @@
 6:	movzbl (%_ASM_AX),%edx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_nocheck_1)
 EXPORT_SYMBOL(__get_user_nocheck_1)
 
@@ -134,7 +134,7 @@
 7:	movzwl (%_ASM_AX),%edx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_nocheck_2)
 EXPORT_SYMBOL(__get_user_nocheck_2)
 
@@ -144,7 +144,7 @@
 8:	movl (%_ASM_AX),%edx
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_nocheck_4)
 EXPORT_SYMBOL(__get_user_nocheck_4)
 
@@ -159,7 +159,7 @@
 #endif
 	xor %eax,%eax
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__get_user_nocheck_8)
 EXPORT_SYMBOL(__get_user_nocheck_8)
 
@@ -169,7 +169,7 @@
 bad_get_user:
 	xor %edx,%edx
 	mov $(-EFAULT),%_ASM_AX
-	ret
+	RET
 SYM_CODE_END(.Lbad_get_user_clac)
 
 #ifdef CONFIG_X86_32
@@ -179,7 +179,7 @@
 	xor %edx,%edx
 	xor %ecx,%ecx
 	mov $(-EFAULT),%_ASM_AX
-	ret
+	RET
 SYM_CODE_END(.Lbad_get_user_8_clac)
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/hweight.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/hweight.S
@@ -32,7 +32,7 @@
 	imull $0x01010101, %eax, %eax		# w_tmp *= 0x01010101
 	shrl $24, %eax				# w = w_tmp >> 24
 	__ASM_SIZE(pop,) %__ASM_REG(dx)
-	ret
+	RET
 SYM_FUNC_END(__sw_hweight32)
 EXPORT_SYMBOL(__sw_hweight32)
 
@@ -65,7 +65,7 @@
 
 	popq    %rdx
 	popq    %rdi
-	ret
+	RET
 #else /* CONFIG_X86_32 */
 	/* We're getting an u64 arg in (%eax,%edx): unsigned long hweight64(__u64 w) */
 	pushl   %ecx
@@ -77,7 +77,7 @@
 	addl    %ecx, %eax                      # result
 
 	popl    %ecx
-	ret
+	RET
 #endif
 SYM_FUNC_END(__sw_hweight64)
 EXPORT_SYMBOL(__sw_hweight64)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/insn-eval.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/insn-eval.c
@@ -412,32 +412,44 @@
 #endif /* CONFIG_X86_64 */
 }
 
-static int get_reg_offset(struct insn *insn, struct pt_regs *regs,
-			  enum reg_type type)
+static const int pt_regoff[] = {
+	offsetof(struct pt_regs, ax),
+	offsetof(struct pt_regs, cx),
+	offsetof(struct pt_regs, dx),
+	offsetof(struct pt_regs, bx),
+	offsetof(struct pt_regs, sp),
+	offsetof(struct pt_regs, bp),
+	offsetof(struct pt_regs, si),
+	offsetof(struct pt_regs, di),
+#ifdef CONFIG_X86_64
+	offsetof(struct pt_regs, r8),
+	offsetof(struct pt_regs, r9),
+	offsetof(struct pt_regs, r10),
+	offsetof(struct pt_regs, r11),
+	offsetof(struct pt_regs, r12),
+	offsetof(struct pt_regs, r13),
+	offsetof(struct pt_regs, r14),
+	offsetof(struct pt_regs, r15),
+#else
+	offsetof(struct pt_regs, ds),
+	offsetof(struct pt_regs, es),
+	offsetof(struct pt_regs, fs),
+	offsetof(struct pt_regs, gs),
+#endif
+};
+
+int pt_regs_offset(struct pt_regs *regs, int regno)
 {
+	if ((unsigned)regno < ARRAY_SIZE(pt_regoff))
+		return pt_regoff[regno];
+	return -EDOM;
+}
+
+static int get_regno(struct insn *insn, enum reg_type type)
+{
+	int nr_registers = ARRAY_SIZE(pt_regoff);
 	int regno = 0;
 
-	static const int regoff[] = {
-		offsetof(struct pt_regs, ax),
-		offsetof(struct pt_regs, cx),
-		offsetof(struct pt_regs, dx),
-		offsetof(struct pt_regs, bx),
-		offsetof(struct pt_regs, sp),
-		offsetof(struct pt_regs, bp),
-		offsetof(struct pt_regs, si),
-		offsetof(struct pt_regs, di),
-#ifdef CONFIG_X86_64
-		offsetof(struct pt_regs, r8),
-		offsetof(struct pt_regs, r9),
-		offsetof(struct pt_regs, r10),
-		offsetof(struct pt_regs, r11),
-		offsetof(struct pt_regs, r12),
-		offsetof(struct pt_regs, r13),
-		offsetof(struct pt_regs, r14),
-		offsetof(struct pt_regs, r15),
-#endif
-	};
-	int nr_registers = ARRAY_SIZE(regoff);
 	/*
 	 * Don't possibly decode a 32-bit instructions as
 	 * reading a 64-bit-only register.
@@ -505,7 +517,18 @@
 		WARN_ONCE(1, "decoded an instruction with an invalid register");
 		return -EINVAL;
 	}
-	return regoff[regno];
+	return regno;
+}
+
+static int get_reg_offset(struct insn *insn, struct pt_regs *regs,
+			  enum reg_type type)
+{
+	int regno = get_regno(insn, type);
+
+	if (regno < 0)
+		return regno;
+
+	return pt_regs_offset(regs, regno);
 }
 
 /**
@@ -1417,7 +1440,7 @@
 	}
 }
 
-static int insn_get_effective_ip(struct pt_regs *regs, unsigned long *ip)
+int insn_get_effective_ip(struct pt_regs *regs, unsigned long *ip)
 {
 	unsigned long seg_base = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/insn.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/insn.c
@@ -13,6 +13,7 @@
 #endif
 #include <asm/inat.h> /*__ignore_sync_check__ */
 #include <asm/insn.h> /* __ignore_sync_check__ */
+#include <asm/unaligned.h> /* __ignore_sync_check__ */
 
 #include <linux/errno.h>
 #include <linux/kconfig.h>
@@ -37,10 +38,10 @@
 	((insn)->next_byte + sizeof(t) + n <= (insn)->end_kaddr)
 
 #define __get_next(t, insn)	\
-	({ t r; memcpy(&r, insn->next_byte, sizeof(t)); insn->next_byte += sizeof(t); leXX_to_cpu(t, r); })
+	({ t r = get_unaligned((t *)(insn)->next_byte); (insn)->next_byte += sizeof(t); leXX_to_cpu(t, r); })
 
 #define __peek_nbyte_next(t, insn, n)	\
-	({ t r; memcpy(&r, (insn)->next_byte + n, sizeof(t)); leXX_to_cpu(t, r); })
+	({ t r = get_unaligned((t *)(insn)->next_byte + n); leXX_to_cpu(t, r); })
 
 #define get_next(t, insn)	\
 	({ if (unlikely(!validate_next(t, insn, 0))) goto err_out; __get_next(t, insn); })
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/iomap_copy_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/iomap_copy_64.S
@@ -10,6 +10,6 @@
  */
 SYM_FUNC_START(__iowrite32_copy)
 	movl %edx,%ecx
-	rep movsd
-	ret
+	rep movsl
+	RET
 SYM_FUNC_END(__iowrite32_copy)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/iomem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/iomem.c
@@ -22,7 +22,7 @@
 		     : "memory");
 }
 
-void memcpy_fromio(void *to, const volatile void __iomem *from, size_t n)
+static void string_memcpy_fromio(void *to, const volatile void __iomem *from, size_t n)
 {
 	if (unlikely(!n))
 		return;
@@ -38,9 +38,8 @@
 	}
 	rep_movs(to, (const void *)from, n);
 }
-EXPORT_SYMBOL(memcpy_fromio);
 
-void memcpy_toio(volatile void __iomem *to, const void *from, size_t n)
+static void string_memcpy_toio(volatile void __iomem *to, const void *from, size_t n)
 {
 	if (unlikely(!n))
 		return;
@@ -56,14 +55,64 @@
 	}
 	rep_movs((void *)to, (const void *) from, n);
 }
+
+static void unrolled_memcpy_fromio(void *to, const volatile void __iomem *from, size_t n)
+{
+	const volatile char __iomem *in = from;
+	char *out = to;
+	int i;
+
+	for (i = 0; i < n; ++i)
+		out[i] = readb(&in[i]);
+}
+
+static void unrolled_memcpy_toio(volatile void __iomem *to, const void *from, size_t n)
+{
+	volatile char __iomem *out = to;
+	const char *in = from;
+	int i;
+
+	for (i = 0; i < n; ++i)
+		writeb(in[i], &out[i]);
+}
+
+static void unrolled_memset_io(volatile void __iomem *a, int b, size_t c)
+{
+	volatile char __iomem *mem = a;
+	int i;
+
+	for (i = 0; i < c; ++i)
+		writeb(b, &mem[i]);
+}
+
+void memcpy_fromio(void *to, const volatile void __iomem *from, size_t n)
+{
+	if (sev_key_active())
+		unrolled_memcpy_fromio(to, from, n);
+	else
+		string_memcpy_fromio(to, from, n);
+}
+EXPORT_SYMBOL(memcpy_fromio);
+
+void memcpy_toio(volatile void __iomem *to, const void *from, size_t n)
+{
+	if (sev_key_active())
+		unrolled_memcpy_toio(to, from, n);
+	else
+		string_memcpy_toio(to, from, n);
+}
 EXPORT_SYMBOL(memcpy_toio);
 
 void memset_io(volatile void __iomem *a, int b, size_t c)
 {
-	/*
-	 * TODO: memset can mangle the IO patterns quite a bit.
-	 * perhaps it would be better to use a dumb one:
-	 */
-	memset((void *)a, b, c);
+	if (sev_key_active()) {
+		unrolled_memset_io(a, b, c);
+	} else {
+		/*
+		 * TODO: memset can mangle the IO patterns quite a bit.
+		 * perhaps it would be better to use a dumb one:
+		 */
+		memset((void *)a, b, c);
+	}
 }
 EXPORT_SYMBOL(memset_io);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/memcpy_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/memcpy_64.S
@@ -39,7 +39,7 @@
 	rep movsq
 	movl %edx, %ecx
 	rep movsb
-	ret
+	RET
 SYM_FUNC_END(memcpy)
 SYM_FUNC_END_ALIAS(__memcpy)
 EXPORT_SYMBOL(memcpy)
@@ -53,7 +53,7 @@
 	movq %rdi, %rax
 	movq %rdx, %rcx
 	rep movsb
-	ret
+	RET
 SYM_FUNC_END(memcpy_erms)
 
 SYM_FUNC_START_LOCAL(memcpy_orig)
@@ -137,7 +137,7 @@
 	movq %r9,	1*8(%rdi)
 	movq %r10,	-2*8(%rdi, %rdx)
 	movq %r11,	-1*8(%rdi, %rdx)
-	retq
+	RET
 	.p2align 4
 .Lless_16bytes:
 	cmpl $8,	%edx
@@ -149,7 +149,7 @@
 	movq -1*8(%rsi, %rdx),	%r9
 	movq %r8,	0*8(%rdi)
 	movq %r9,	-1*8(%rdi, %rdx)
-	retq
+	RET
 	.p2align 4
 .Lless_8bytes:
 	cmpl $4,	%edx
@@ -162,7 +162,7 @@
 	movl -4(%rsi, %rdx), %r8d
 	movl %ecx, (%rdi)
 	movl %r8d, -4(%rdi, %rdx)
-	retq
+	RET
 	.p2align 4
 .Lless_3bytes:
 	subl $1, %edx
@@ -180,7 +180,7 @@
 	movb %cl, (%rdi)
 
 .Lend:
-	retq
+	RET
 SYM_FUNC_END(memcpy_orig)
 
 .popsection
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/memmove_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/memmove_64.S
@@ -40,7 +40,7 @@
 	/* FSRM implies ERMS => no length checks, do the copy directly */
 .Lmemmove_begin_forward:
 	ALTERNATIVE "cmp $0x20, %rdx; jb 1f", "", X86_FEATURE_FSRM
-	ALTERNATIVE "", "movq %rdx, %rcx; rep movsb; retq", X86_FEATURE_ERMS
+	ALTERNATIVE "", "jmp .Lmemmove_erms", X86_FEATURE_ERMS
 
 	/*
 	 * movsq instruction have many startup latency
@@ -205,7 +205,12 @@
 	movb (%rsi), %r11b
 	movb %r11b, (%rdi)
 13:
-	retq
+	RET
+
+.Lmemmove_erms:
+	movq %rdx, %rcx
+	rep movsb
+	RET
 SYM_FUNC_END(__memmove)
 SYM_FUNC_END_ALIAS(memmove)
 EXPORT_SYMBOL(__memmove)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/memset_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/memset_64.S
@@ -40,7 +40,7 @@
 	movl %edx,%ecx
 	rep stosb
 	movq %r9,%rax
-	ret
+	RET
 SYM_FUNC_END(__memset)
 SYM_FUNC_END_ALIAS(memset)
 EXPORT_SYMBOL(memset)
@@ -63,7 +63,7 @@
 	movq %rdx,%rcx
 	rep stosb
 	movq %r9,%rax
-	ret
+	RET
 SYM_FUNC_END(memset_erms)
 
 SYM_FUNC_START_LOCAL(memset_orig)
@@ -125,7 +125,7 @@
 
 .Lende:
 	movq	%r10,%rax
-	ret
+	RET
 
 .Lbad_alignment:
 	cmpq $7,%rdx
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/misc.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/misc.c
@@ -6,7 +6,7 @@
  */
 int num_digits(int val)
 {
-	int m = 10;
+	long long m = 10;
 	int d = 1;
 
 	if (val < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/msr-reg.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/msr-reg.S
@@ -35,7 +35,7 @@
 	movl    %edi, 28(%r10)
 	popq %r12
 	popq %rbx
-	ret
+	RET
 3:
 	movl    $-EIO, %r11d
 	jmp     2b
@@ -77,7 +77,7 @@
 	popl %esi
 	popl %ebp
 	popl %ebx
-	ret
+	RET
 3:
 	movl    $-EIO, 4(%esp)
 	jmp     2b
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/putuser.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/putuser.S
@@ -52,7 +52,7 @@
 1:	movb %al,(%_ASM_CX)
 	xor %ecx,%ecx
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__put_user_1)
 EXPORT_SYMBOL(__put_user_1)
 EXPORT_SYMBOL(__put_user_nocheck_1)
@@ -66,7 +66,7 @@
 2:	movw %ax,(%_ASM_CX)
 	xor %ecx,%ecx
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__put_user_2)
 EXPORT_SYMBOL(__put_user_2)
 EXPORT_SYMBOL(__put_user_nocheck_2)
@@ -80,7 +80,7 @@
 3:	movl %eax,(%_ASM_CX)
 	xor %ecx,%ecx
 	ASM_CLAC
-	ret
+	RET
 SYM_FUNC_END(__put_user_4)
 EXPORT_SYMBOL(__put_user_4)
 EXPORT_SYMBOL(__put_user_nocheck_4)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/retpoline.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/retpoline.S
@@ -9,8 +9,9 @@
 #include <asm/nospec-branch.h>
 #include <asm/unwind_hints.h>
 #include <asm/frame.h>
+#include <asm/nops.h>
 
-	.section .text.__x86.indirect_thunk
+	.section .text..__x86.indirect_thunk
 
 .macro RETPOLINE reg
 	ANNOTATE_INTRA_FUNCTION_CALL
@@ -23,50 +24,18 @@
 .Ldo_rop_\@:
 	mov     %\reg, (%_ASM_SP)
 	UNWIND_HINT_FUNC
-	ret
+	RET
 .endm
 
 .macro THUNK reg
 
-	.align 32
-
-SYM_FUNC_START(__x86_indirect_thunk_\reg)
-
-	ALTERNATIVE_2 __stringify(ANNOTATE_RETPOLINE_SAFE; jmp *%\reg), \
-		      __stringify(RETPOLINE \reg), X86_FEATURE_RETPOLINE, \
-		      __stringify(lfence; ANNOTATE_RETPOLINE_SAFE; jmp *%\reg), X86_FEATURE_RETPOLINE_AMD
-
-SYM_FUNC_END(__x86_indirect_thunk_\reg)
-
-.endm
-
-/*
- * This generates .altinstr_replacement symbols for use by objtool. They,
- * however, must not actually live in .altinstr_replacement since that will be
- * discarded after init, but module alternatives will also reference these
- * symbols.
- *
- * Their names matches the "__x86_indirect_" prefix to mark them as retpolines.
- */
-.macro ALT_THUNK reg
-
-	.align 1
-
-SYM_FUNC_START_NOALIGN(__x86_indirect_alt_call_\reg)
-	ANNOTATE_RETPOLINE_SAFE
-1:	call	*%\reg
-2:	.skip	5-(2b-1b), 0x90
-SYM_FUNC_END(__x86_indirect_alt_call_\reg)
-
-STACK_FRAME_NON_STANDARD(__x86_indirect_alt_call_\reg)
-
-SYM_FUNC_START_NOALIGN(__x86_indirect_alt_jmp_\reg)
-	ANNOTATE_RETPOLINE_SAFE
-1:	jmp	*%\reg
-2:	.skip	5-(2b-1b), 0x90
-SYM_FUNC_END(__x86_indirect_alt_jmp_\reg)
+	.align RETPOLINE_THUNK_SIZE
+SYM_INNER_LABEL(__x86_indirect_thunk_\reg, SYM_L_GLOBAL)
+	UNWIND_HINT_EMPTY
 
-STACK_FRAME_NON_STANDARD(__x86_indirect_alt_jmp_\reg)
+	ALTERNATIVE_2 __stringify(RETPOLINE \reg), \
+		      __stringify(lfence; ANNOTATE_RETPOLINE_SAFE; jmp *%\reg; int3), X86_FEATURE_RETPOLINE_LFENCE, \
+		      __stringify(ANNOTATE_RETPOLINE_SAFE; jmp *%\reg), ALT_NOT(X86_FEATURE_RETPOLINE)
 
 .endm
 
@@ -85,22 +54,213 @@
 #define __EXPORT_THUNK(sym)	_ASM_NOKPROBE(sym); EXPORT_SYMBOL(sym)
 #define EXPORT_THUNK(reg)	__EXPORT_THUNK(__x86_indirect_thunk_ ## reg)
 
-#undef GEN
+	.align RETPOLINE_THUNK_SIZE
+SYM_CODE_START(__x86_indirect_thunk_array)
+
 #define GEN(reg) THUNK reg
 #include <asm/GEN-for-each-reg.h>
-
 #undef GEN
+
+	.align RETPOLINE_THUNK_SIZE
+SYM_CODE_END(__x86_indirect_thunk_array)
+
 #define GEN(reg) EXPORT_THUNK(reg)
 #include <asm/GEN-for-each-reg.h>
-
 #undef GEN
-#define GEN(reg) ALT_THUNK reg
-#include <asm/GEN-for-each-reg.h>
 
-#undef GEN
-#define GEN(reg) __EXPORT_THUNK(__x86_indirect_alt_call_ ## reg)
-#include <asm/GEN-for-each-reg.h>
+/*
+ * This function name is magical and is used by -mfunction-return=thunk-extern
+ * for the compiler to generate JMPs to it.
+ */
+#ifdef CONFIG_RETHUNK
 
-#undef GEN
-#define GEN(reg) __EXPORT_THUNK(__x86_indirect_alt_jmp_ ## reg)
-#include <asm/GEN-for-each-reg.h>
+/*
+ * srso_alias_untrain_ret() and srso_alias_safe_ret() are placed at
+ * special addresses:
+ *
+ * - srso_alias_untrain_ret() is 2M aligned
+ * - srso_alias_safe_ret() is also in the same 2M page but bits 2, 8, 14
+ * and 20 in its virtual address are set (while those bits in the
+ * srso_alias_untrain_ret() function are cleared).
+ *
+ * This guarantees that those two addresses will alias in the branch
+ * target buffer of Zen3/4 generations, leading to any potential
+ * poisoned entries at that BTB slot to get evicted.
+ *
+ * As a result, srso_alias_safe_ret() becomes a safe return.
+ */
+#ifdef CONFIG_CPU_SRSO
+	.section .text..__x86.rethunk_untrain
+
+SYM_START(srso_alias_untrain_ret, SYM_L_GLOBAL, SYM_A_NONE)
+	UNWIND_HINT_FUNC
+	ASM_NOP2
+	lfence
+	jmp srso_alias_return_thunk
+SYM_FUNC_END(srso_alias_untrain_ret)
+__EXPORT_THUNK(srso_alias_untrain_ret)
+
+	.section .text..__x86.rethunk_safe
+#else
+/* dummy definition for alternatives */
+SYM_START(srso_alias_untrain_ret, SYM_L_GLOBAL, SYM_A_NONE)
+	ANNOTATE_UNRET_SAFE
+	ret
+	int3
+SYM_FUNC_END(srso_alias_untrain_ret)
+__EXPORT_THUNK(srso_alias_untrain_ret)
+#endif
+
+SYM_START(srso_alias_safe_ret, SYM_L_GLOBAL, SYM_A_NONE)
+	lea 8(%_ASM_SP), %_ASM_SP
+	UNWIND_HINT_FUNC
+	ANNOTATE_UNRET_SAFE
+	ret
+	int3
+SYM_FUNC_END(srso_alias_safe_ret)
+
+	.section .text..__x86.return_thunk
+
+SYM_CODE_START(srso_alias_return_thunk)
+	UNWIND_HINT_FUNC
+	ANNOTATE_NOENDBR
+	call srso_alias_safe_ret
+	ud2
+SYM_CODE_END(srso_alias_return_thunk)
+
+/*
+ * Some generic notes on the untraining sequences:
+ *
+ * They are interchangeable when it comes to flushing potentially wrong
+ * RET predictions from the BTB.
+ *
+ * The SRSO Zen1/2 (MOVABS) untraining sequence is longer than the
+ * Retbleed sequence because the return sequence done there
+ * (srso_safe_ret()) is longer and the return sequence must fully nest
+ * (end before) the untraining sequence. Therefore, the untraining
+ * sequence must fully overlap the return sequence.
+ *
+ * Regarding alignment - the instructions which need to be untrained,
+ * must all start at a cacheline boundary for Zen1/2 generations. That
+ * is, instruction sequences starting at srso_safe_ret() and
+ * the respective instruction sequences at retbleed_return_thunk()
+ * must start at a cacheline boundary.
+ */
+
+/*
+ * Safety details here pertain to the AMD Zen{1,2} microarchitecture:
+ * 1) The RET at retbleed_return_thunk must be on a 64 byte boundary, for
+ *    alignment within the BTB.
+ * 2) The instruction at retbleed_untrain_ret must contain, and not
+ *    end with, the 0xc3 byte of the RET.
+ * 3) STIBP must be enabled, or SMT disabled, to prevent the sibling thread
+ *    from re-poisioning the BTB prediction.
+ */
+	.align 64
+	.skip 64 - (retbleed_return_thunk - retbleed_untrain_ret), 0xcc
+SYM_FUNC_START_NOALIGN(retbleed_untrain_ret);
+
+	/*
+	 * As executed from retbleed_untrain_ret, this is:
+	 *
+	 *   TEST $0xcc, %bl
+	 *   LFENCE
+	 *   JMP retbleed_return_thunk
+	 *
+	 * Executing the TEST instruction has a side effect of evicting any BTB
+	 * prediction (potentially attacker controlled) attached to the RET, as
+	 * retbleed_return_thunk + 1 isn't an instruction boundary at the moment.
+	 */
+	.byte	0xf6
+
+	/*
+	 * As executed from retbleed_return_thunk, this is a plain RET.
+	 *
+	 * As part of the TEST above, RET is the ModRM byte, and INT3 the imm8.
+	 *
+	 * We subsequently jump backwards and architecturally execute the RET.
+	 * This creates a correct BTB prediction (type=ret), but in the
+	 * meantime we suffer Straight Line Speculation (because the type was
+	 * no branch) which is halted by the INT3.
+	 *
+	 * With SMT enabled and STIBP active, a sibling thread cannot poison
+	 * RET's prediction to a type of its choice, but can evict the
+	 * prediction due to competitive sharing. If the prediction is
+	 * evicted, retbleed_return_thunk will suffer Straight Line Speculation
+	 * which will be contained safely by the INT3.
+	 */
+SYM_INNER_LABEL(retbleed_return_thunk, SYM_L_GLOBAL)
+	ret
+	int3
+SYM_CODE_END(retbleed_return_thunk)
+
+	/*
+	 * Ensure the TEST decoding / BTB invalidation is complete.
+	 */
+	lfence
+
+	/*
+	 * Jump back and execute the RET in the middle of the TEST instruction.
+	 * INT3 is for SLS protection.
+	 */
+	jmp retbleed_return_thunk
+	int3
+SYM_FUNC_END(retbleed_untrain_ret)
+__EXPORT_THUNK(retbleed_untrain_ret)
+
+/*
+ * SRSO untraining sequence for Zen1/2, similar to retbleed_untrain_ret()
+ * above. On kernel entry, srso_untrain_ret() is executed which is a
+ *
+ * movabs $0xccccc30824648d48,%rax
+ *
+ * and when the return thunk executes the inner label srso_safe_ret()
+ * later, it is a stack manipulation and a RET which is mispredicted and
+ * thus a "safe" one to use.
+ */
+	.align 64
+	.skip 64 - (srso_safe_ret - srso_untrain_ret), 0xcc
+SYM_START(srso_untrain_ret, SYM_L_GLOBAL, SYM_A_NONE)
+	.byte 0x48, 0xb8
+
+/*
+ * This forces the function return instruction to speculate into a trap
+ * (UD2 in srso_return_thunk() below).  This RET will then mispredict
+ * and execution will continue at the return site read from the top of
+ * the stack.
+ */
+SYM_INNER_LABEL(srso_safe_ret, SYM_L_GLOBAL)
+	lea 8(%_ASM_SP), %_ASM_SP
+	ret
+	int3
+	int3
+	/* end of movabs */
+	lfence
+	call srso_safe_ret
+	ud2
+SYM_CODE_END(srso_safe_ret)
+SYM_FUNC_END(srso_untrain_ret)
+__EXPORT_THUNK(srso_untrain_ret)
+
+SYM_CODE_START(srso_return_thunk)
+	UNWIND_HINT_FUNC
+	ANNOTATE_NOENDBR
+	call srso_safe_ret
+	ud2
+SYM_CODE_END(srso_return_thunk)
+
+SYM_FUNC_START(entry_untrain_ret)
+	ALTERNATIVE "jmp retbleed_untrain_ret", "jmp srso_untrain_ret", X86_FEATURE_SRSO
+SYM_FUNC_END(entry_untrain_ret)
+__EXPORT_THUNK(entry_untrain_ret)
+
+SYM_CODE_START(__x86_return_thunk)
+	UNWIND_HINT_FUNC
+	ANNOTATE_NOENDBR
+	ANNOTATE_UNRET_SAFE
+	ret
+	int3
+SYM_CODE_END(__x86_return_thunk)
+EXPORT_SYMBOL(__x86_return_thunk)
+
+#endif /* CONFIG_RETHUNK */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/usercopy_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/usercopy_64.c
@@ -121,7 +121,7 @@
 
 	/* cache copy and flush to align dest */
 	if (!IS_ALIGNED(dest, 8)) {
-		unsigned len = min_t(unsigned, size, ALIGN(dest, 8) - dest);
+		size_t len = min_t(size_t, size, ALIGN(dest, 8) - dest);
 
 		memcpy((void *) dest, (void *) source, len);
 		clean_cache_range((void *) dest, len);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/lib/x86-opcode-map.txt
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/lib/x86-opcode-map.txt
@@ -148,7 +148,7 @@
 65: SEG=GS (Prefix)
 66: Operand-Size (Prefix)
 67: Address-Size (Prefix)
-68: PUSH Iz (d64)
+68: PUSH Iz
 69: IMUL Gv,Ev,Iz
 6a: PUSH Ib (d64)
 6b: IMUL Gv,Ev,Ib
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/div_Xsig.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/div_Xsig.S
@@ -341,7 +341,7 @@
 	popl	%esi
 
 	leave
-	ret
+	RET
 
 
 #ifdef PARANOID
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/div_small.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/div_small.S
@@ -44,5 +44,5 @@
 	popl	%esi
 
 	leave
-	ret
+	RET
 SYM_FUNC_END(FPU_div_small)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/fpu_aux.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/fpu_aux.c
@@ -53,7 +53,7 @@
 
 void finit(void)
 {
-	fpstate_init_soft(&current->thread.fpu.state.soft);
+	fpstate_init_soft(&current->thread.fpu.fpstate->regs.soft);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/fpu_entry.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/fpu_entry.c
@@ -31,7 +31,7 @@
 #include <linux/uaccess.h>
 #include <asm/traps.h>
 #include <asm/user.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 
 #include "fpu_system.h"
 #include "fpu_emu.h"
@@ -640,7 +640,7 @@
 		    unsigned int pos, unsigned int count,
 		    const void *kbuf, const void __user *ubuf)
 {
-	struct swregs_state *s387 = &target->thread.fpu.state.soft;
+	struct swregs_state *s387 = &target->thread.fpu.fpstate->regs.soft;
 	void *space = s387->st_space;
 	int ret;
 	int offset, other, i, tags, regnr, tag, newtop;
@@ -691,7 +691,7 @@
 		    const struct user_regset *regset,
 		    struct membuf to)
 {
-	struct swregs_state *s387 = &target->thread.fpu.state.soft;
+	struct swregs_state *s387 = &target->thread.fpu.fpstate->regs.soft;
 	const void *space = s387->st_space;
 	int offset = (S387->ftop & 7) * 10, other = 80 - offset;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/fpu_system.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/fpu_system.h
@@ -73,7 +73,7 @@
 	return (d->type & SEG_TYPE_EXECUTE_MASK) == SEG_TYPE_WRITABLE;
 }
 
-#define I387			(&current->thread.fpu.state)
+#define I387			(&current->thread.fpu.fpstate->regs)
 #define FPU_info		(I387->soft.info)
 
 #define FPU_CS			(*(unsigned short *) &(FPU_info->regs->cs))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/mul_Xsig.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/mul_Xsig.S
@@ -62,7 +62,7 @@
 
 	popl %esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(mul32_Xsig)
 
 
@@ -115,7 +115,7 @@
 
 	popl %esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(mul64_Xsig)
 
 
@@ -175,5 +175,5 @@
 
 	popl %esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(mul_Xsig_Xsig)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/polynom_Xsig.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/polynom_Xsig.S
@@ -133,5 +133,5 @@
 	popl	%edi
 	popl	%esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(polynomial_Xsig)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/reg_norm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/reg_norm.S
@@ -72,7 +72,7 @@
 L_exit:
 	popl	%ebx
 	leave
-	ret
+	RET
 
 
 L_zero:
@@ -138,7 +138,7 @@
 
 	popl	%ebx
 	leave
-	ret
+	RET
 
 L_exit_nuo_zero:
 	movl	TAG_Zero,%eax
@@ -146,5 +146,5 @@
 
 	popl	%ebx
 	leave
-	ret
+	RET
 SYM_FUNC_END(FPU_normalize_nuo)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/reg_round.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/reg_round.S
@@ -437,7 +437,7 @@
 	popl	%edi
 	popl	%esi
 	leave
-	ret
+	RET
 
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/reg_u_add.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/reg_u_add.S
@@ -164,6 +164,6 @@
 	popl	%edi
 	popl	%esi
 	leave
-	ret
+	RET
 #endif /* PARANOID */
 SYM_FUNC_END(FPU_u_add)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/reg_u_div.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/reg_u_div.S
@@ -468,7 +468,7 @@
 	popl	%esi
 
 	leave
-	ret
+	RET
 #endif /* PARANOID */ 
 
 SYM_FUNC_END(FPU_u_div)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/reg_u_mul.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/reg_u_mul.S
@@ -144,7 +144,7 @@
 	popl	%edi
 	popl	%esi
 	leave
-	ret
+	RET
 #endif /* PARANOID */ 
 
 SYM_FUNC_END(FPU_u_mul)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/reg_u_sub.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/reg_u_sub.S
@@ -270,5 +270,5 @@
 	popl	%edi
 	popl	%esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(FPU_u_sub)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/round_Xsig.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/round_Xsig.S
@@ -78,7 +78,7 @@
 	popl	%esi
 	popl	%ebx
 	leave
-	ret
+	RET
 SYM_FUNC_END(round_Xsig)
 
 
@@ -138,5 +138,5 @@
 	popl	%esi
 	popl	%ebx
 	leave
-	ret
+	RET
 SYM_FUNC_END(norm_Xsig)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/shr_Xsig.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/shr_Xsig.S
@@ -45,7 +45,7 @@
 	popl	%ebx
 	popl	%esi
 	leave
-	ret
+	RET
 
 L_more_than_31:
 	cmpl	$64,%ecx
@@ -61,7 +61,7 @@
 	movl	$0,8(%esi)
 	popl	%esi
 	leave
-	ret
+	RET
 
 L_more_than_63:
 	cmpl	$96,%ecx
@@ -76,7 +76,7 @@
 	movl	%edx,8(%esi)
 	popl	%esi
 	leave
-	ret
+	RET
 
 L_more_than_95:
 	xorl	%eax,%eax
@@ -85,5 +85,5 @@
 	movl	%eax,8(%esi)
 	popl	%esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(shr_Xsig)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/math-emu/wm_shrx.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/math-emu/wm_shrx.S
@@ -55,7 +55,7 @@
 	popl	%ebx
 	popl	%esi
 	leave
-	ret
+	RET
 
 L_more_than_31:
 	cmpl	$64,%ecx
@@ -70,7 +70,7 @@
 	movl	$0,4(%esi)
 	popl	%esi
 	leave
-	ret
+	RET
 
 L_more_than_63:
 	cmpl	$96,%ecx
@@ -84,7 +84,7 @@
 	movl	%edx,4(%esi)
 	popl	%esi
 	leave
-	ret
+	RET
 
 L_more_than_95:
 	xorl	%eax,%eax
@@ -92,7 +92,7 @@
 	movl	%eax,4(%esi)
 	popl	%esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(FPU_shrx)
 
 
@@ -146,7 +146,7 @@
 	popl	%ebx
 	popl	%esi
 	leave
-	ret
+	RET
 
 /* Shift by [0..31] bits */
 Ls_less_than_32:
@@ -163,7 +163,7 @@
 	popl	%ebx
 	popl	%esi
 	leave
-	ret
+	RET
 
 /* Shift by [64..95] bits */
 Ls_more_than_63:
@@ -189,7 +189,7 @@
 	popl	%ebx
 	popl	%esi
 	leave
-	ret
+	RET
 
 Ls_more_than_95:
 /* Shift by [96..inf) bits */
@@ -203,5 +203,5 @@
 	popl	%ebx
 	popl	%esi
 	leave
-	ret
+	RET
 SYM_FUNC_END(FPU_shrxs)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/Makefile
@@ -1,10 +1,10 @@
 # SPDX-License-Identifier: GPL-2.0
 # Kernel does not boot with instrumentation of tlb.c and mem_encrypt*.c
 KCOV_INSTRUMENT_tlb.o			:= n
-KCOV_INSTRUMENT_mem_encrypt.o		:= n
+KCOV_INSTRUMENT_mem_encrypt_amd.o	:= n
 KCOV_INSTRUMENT_mem_encrypt_identity.o	:= n
 
-KASAN_SANITIZE_mem_encrypt.o		:= n
+KASAN_SANITIZE_mem_encrypt_amd.o	:= n
 KASAN_SANITIZE_mem_encrypt_identity.o	:= n
 
 # Disable KCSAN entirely, because otherwise we get warnings that some functions
@@ -12,7 +12,7 @@
 KCSAN_SANITIZE := n
 
 ifdef CONFIG_FUNCTION_TRACER
-CFLAGS_REMOVE_mem_encrypt.o		= -pg
+CFLAGS_REMOVE_mem_encrypt_amd.o		= -pg
 CFLAGS_REMOVE_mem_encrypt_identity.o	= -pg
 endif
 
@@ -52,6 +52,6 @@
 obj-$(CONFIG_RANDOMIZE_MEMORY)			+= kaslr.o
 obj-$(CONFIG_PAGE_TABLE_ISOLATION)		+= pti.o
 
-obj-$(CONFIG_AMD_MEM_ENCRYPT)	+= mem_encrypt.o
+obj-$(CONFIG_AMD_MEM_ENCRYPT)	+= mem_encrypt_amd.o
 obj-$(CONFIG_AMD_MEM_ENCRYPT)	+= mem_encrypt_identity.o
 obj-$(CONFIG_AMD_MEM_ENCRYPT)	+= mem_encrypt_boot.o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/cpu_entry_area.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/cpu_entry_area.c
@@ -5,26 +5,72 @@
 #include <linux/kallsyms.h>
 #include <linux/kcore.h>
 #include <linux/pgtable.h>
+#include <linux/random.h>
 
 #include <asm/cpu_entry_area.h>
 #include <asm/fixmap.h>
 #include <asm/desc.h>
+#include <asm/kasan.h>
+#include <asm/setup.h>
 
 static DEFINE_PER_CPU_PAGE_ALIGNED(struct entry_stack_page, entry_stack_storage);
 
 #ifdef CONFIG_X86_64
 static DEFINE_PER_CPU_PAGE_ALIGNED(struct exception_stacks, exception_stacks);
 DEFINE_PER_CPU(struct cea_exception_stacks*, cea_exception_stacks);
-#endif
 
-#ifdef CONFIG_X86_32
+static DEFINE_PER_CPU_READ_MOSTLY(unsigned long, _cea_offset);
+
+static __always_inline unsigned int cea_offset(unsigned int cpu)
+{
+	return per_cpu(_cea_offset, cpu);
+}
+
+static __init void init_cea_offsets(void)
+{
+	unsigned int max_cea;
+	unsigned int i, j;
+
+	if (!kaslr_enabled()) {
+		for_each_possible_cpu(i)
+			per_cpu(_cea_offset, i) = i;
+		return;
+	}
+
+	max_cea = (CPU_ENTRY_AREA_MAP_SIZE - PAGE_SIZE) / CPU_ENTRY_AREA_SIZE;
+
+	/* O(sodding terrible) */
+	for_each_possible_cpu(i) {
+		unsigned int cea;
+
+again:
+		cea = prandom_u32_max(max_cea);
+
+		for_each_possible_cpu(j) {
+			if (cea_offset(j) == cea)
+				goto again;
+
+			if (i == j)
+				break;
+		}
+
+		per_cpu(_cea_offset, i) = cea;
+	}
+}
+#else /* !X86_64 */
 DECLARE_PER_CPU_PAGE_ALIGNED(struct doublefault_stack, doublefault_stack);
+
+static __always_inline unsigned int cea_offset(unsigned int cpu)
+{
+	return cpu;
+}
+static inline void init_cea_offsets(void) { }
 #endif
 
 /* Is called from entry code, so must be noinstr */
 noinstr struct cpu_entry_area *get_cpu_entry_area(int cpu)
 {
-	unsigned long va = CPU_ENTRY_AREA_PER_CPU + cpu * CPU_ENTRY_AREA_SIZE;
+	unsigned long va = CPU_ENTRY_AREA_PER_CPU + cea_offset(cpu) * CPU_ENTRY_AREA_SIZE;
 	BUILD_BUG_ON(sizeof(struct cpu_entry_area) % PAGE_SIZE != 0);
 
 	return (struct cpu_entry_area *) va;
@@ -110,6 +156,13 @@
 	cea_map_stack(NMI);
 	cea_map_stack(DB);
 	cea_map_stack(MCE);
+
+	if (IS_ENABLED(CONFIG_AMD_MEM_ENCRYPT)) {
+		if (cc_platform_has(CC_ATTR_GUEST_STATE_ENCRYPT)) {
+			cea_map_stack(VC);
+			cea_map_stack(VC2);
+		}
+	}
 }
 #else
 static inline void percpu_setup_exception_stacks(unsigned int cpu)
@@ -145,6 +198,9 @@
 	pgprot_t tss_prot = PAGE_KERNEL;
 #endif
 
+	kasan_populate_shadow_for_vaddr(cea, CPU_ENTRY_AREA_SIZE,
+					early_cpu_to_node(cpu));
+
 	cea_set_pte(&cea->gdt, get_cpu_gdt_paddr(cpu), gdt_prot);
 
 	cea_map_percpu_pages(&cea->entry_stack_page,
@@ -198,7 +254,6 @@
 
 	/* The +1 is for the readonly IDT: */
 	BUILD_BUG_ON((CPU_ENTRY_AREA_PAGES+1)*PAGE_SIZE != CPU_ENTRY_AREA_MAP_SIZE);
-	BUILD_BUG_ON(CPU_ENTRY_AREA_TOTAL_SIZE != CPU_ENTRY_AREA_MAP_SIZE);
 	BUG_ON(CPU_ENTRY_AREA_BASE & ~PMD_MASK);
 
 	start = CPU_ENTRY_AREA_BASE;
@@ -214,6 +269,8 @@
 {
 	unsigned int cpu;
 
+	init_cea_offsets();
+
 	setup_cpu_entry_area_ptes();
 
 	for_each_possible_cpu(cpu)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/extable.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/extable.c
@@ -2,48 +2,50 @@
 #include <linux/extable.h>
 #include <linux/uaccess.h>
 #include <linux/sched/debug.h>
+#include <linux/bitfield.h>
 #include <xen/xen.h>
 
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/sev.h>
 #include <asm/traps.h>
 #include <asm/kdebug.h>
+#include <asm/insn-eval.h>
 
-typedef bool (*ex_handler_t)(const struct exception_table_entry *,
-			    struct pt_regs *, int, unsigned long,
-			    unsigned long);
+static inline unsigned long *pt_regs_nr(struct pt_regs *regs, int nr)
+{
+	int reg_offset = pt_regs_offset(regs, nr);
+	static unsigned long __dummy;
+
+	if (WARN_ON_ONCE(reg_offset < 0))
+		return &__dummy;
+
+	return (unsigned long *)((unsigned long)regs + reg_offset);
+}
 
 static inline unsigned long
 ex_fixup_addr(const struct exception_table_entry *x)
 {
 	return (unsigned long)&x->fixup + x->fixup;
 }
-static inline ex_handler_t
-ex_fixup_handler(const struct exception_table_entry *x)
-{
-	return (ex_handler_t)((unsigned long)&x->handler + x->handler);
-}
 
-__visible bool ex_handler_default(const struct exception_table_entry *fixup,
-				  struct pt_regs *regs, int trapnr,
-				  unsigned long error_code,
-				  unsigned long fault_addr)
+static bool ex_handler_default(const struct exception_table_entry *e,
+			       struct pt_regs *regs)
 {
-	regs->ip = ex_fixup_addr(fixup);
+	if (e->data & EX_FLAG_CLEAR_AX)
+		regs->ax = 0;
+	if (e->data & EX_FLAG_CLEAR_DX)
+		regs->dx = 0;
+
+	regs->ip = ex_fixup_addr(e);
 	return true;
 }
-EXPORT_SYMBOL(ex_handler_default);
 
-__visible bool ex_handler_fault(const struct exception_table_entry *fixup,
-				struct pt_regs *regs, int trapnr,
-				unsigned long error_code,
-				unsigned long fault_addr)
+static bool ex_handler_fault(const struct exception_table_entry *fixup,
+			     struct pt_regs *regs, int trapnr)
 {
-	regs->ip = ex_fixup_addr(fixup);
 	regs->ax = trapnr;
-	return true;
+	return ex_handler_default(fixup, regs);
 }
-EXPORT_SYMBOL_GPL(ex_handler_fault);
 
 /*
  * Handler for when we fail to restore a task's FPU state.  We should never get
@@ -55,111 +57,88 @@
  * of vulnerability by restoring from the initial state (essentially, zeroing
  * out all the FPU registers) if we can't restore from the task's FPU state.
  */
-__visible bool ex_handler_fprestore(const struct exception_table_entry *fixup,
-				    struct pt_regs *regs, int trapnr,
-				    unsigned long error_code,
-				    unsigned long fault_addr)
+static bool ex_handler_fprestore(const struct exception_table_entry *fixup,
+				 struct pt_regs *regs)
 {
 	regs->ip = ex_fixup_addr(fixup);
 
 	WARN_ONCE(1, "Bad FPU state detected at %pB, reinitializing FPU registers.",
 		  (void *)instruction_pointer(regs));
 
-	__restore_fpregs_from_fpstate(&init_fpstate, xfeatures_mask_fpstate());
+	fpu_reset_from_exception_fixup();
 	return true;
 }
-EXPORT_SYMBOL_GPL(ex_handler_fprestore);
 
-__visible bool ex_handler_uaccess(const struct exception_table_entry *fixup,
-				  struct pt_regs *regs, int trapnr,
-				  unsigned long error_code,
-				  unsigned long fault_addr)
+static bool ex_handler_uaccess(const struct exception_table_entry *fixup,
+			       struct pt_regs *regs, int trapnr)
 {
 	WARN_ONCE(trapnr == X86_TRAP_GP, "General protection fault in user access. Non-canonical address?");
-	regs->ip = ex_fixup_addr(fixup);
-	return true;
+	return ex_handler_default(fixup, regs);
 }
-EXPORT_SYMBOL(ex_handler_uaccess);
 
-__visible bool ex_handler_copy(const struct exception_table_entry *fixup,
-			       struct pt_regs *regs, int trapnr,
-			       unsigned long error_code,
-			       unsigned long fault_addr)
+static bool ex_handler_copy(const struct exception_table_entry *fixup,
+			    struct pt_regs *regs, int trapnr)
 {
 	WARN_ONCE(trapnr == X86_TRAP_GP, "General protection fault in user access. Non-canonical address?");
-	regs->ip = ex_fixup_addr(fixup);
-	regs->ax = trapnr;
-	return true;
+	return ex_handler_fault(fixup, regs, trapnr);
 }
-EXPORT_SYMBOL(ex_handler_copy);
 
-__visible bool ex_handler_rdmsr_unsafe(const struct exception_table_entry *fixup,
-				       struct pt_regs *regs, int trapnr,
-				       unsigned long error_code,
-				       unsigned long fault_addr)
+static bool ex_handler_msr(const struct exception_table_entry *fixup,
+			   struct pt_regs *regs, bool wrmsr, bool safe, int reg)
 {
-	if (pr_warn_once("unchecked MSR access error: RDMSR from 0x%x at rIP: 0x%lx (%pS)\n",
-			 (unsigned int)regs->cx, regs->ip, (void *)regs->ip))
+	if (__ONCE_LITE_IF(!safe && wrmsr)) {
+		pr_warn("unchecked MSR access error: WRMSR to 0x%x (tried to write 0x%08x%08x) at rIP: 0x%lx (%pS)\n",
+			(unsigned int)regs->cx, (unsigned int)regs->dx,
+			(unsigned int)regs->ax,  regs->ip, (void *)regs->ip);
 		show_stack_regs(regs);
+	}
 
-	/* Pretend that the read succeeded and returned 0. */
-	regs->ip = ex_fixup_addr(fixup);
-	regs->ax = 0;
-	regs->dx = 0;
-	return true;
-}
-EXPORT_SYMBOL(ex_handler_rdmsr_unsafe);
-
-__visible bool ex_handler_wrmsr_unsafe(const struct exception_table_entry *fixup,
-				       struct pt_regs *regs, int trapnr,
-				       unsigned long error_code,
-				       unsigned long fault_addr)
-{
-	if (pr_warn_once("unchecked MSR access error: WRMSR to 0x%x (tried to write 0x%08x%08x) at rIP: 0x%lx (%pS)\n",
-			 (unsigned int)regs->cx, (unsigned int)regs->dx,
-			 (unsigned int)regs->ax,  regs->ip, (void *)regs->ip))
+	if (__ONCE_LITE_IF(!safe && !wrmsr)) {
+		pr_warn("unchecked MSR access error: RDMSR from 0x%x at rIP: 0x%lx (%pS)\n",
+			(unsigned int)regs->cx, regs->ip, (void *)regs->ip);
 		show_stack_regs(regs);
+	}
 
-	/* Pretend that the write succeeded. */
-	regs->ip = ex_fixup_addr(fixup);
-	return true;
+	if (!wrmsr) {
+		/* Pretend that the read succeeded and returned 0. */
+		regs->ax = 0;
+		regs->dx = 0;
+	}
+
+	if (safe)
+		*pt_regs_nr(regs, reg) = -EIO;
+
+	return ex_handler_default(fixup, regs);
 }
-EXPORT_SYMBOL(ex_handler_wrmsr_unsafe);
 
-__visible bool ex_handler_clear_fs(const struct exception_table_entry *fixup,
-				   struct pt_regs *regs, int trapnr,
-				   unsigned long error_code,
-				   unsigned long fault_addr)
+static bool ex_handler_clear_fs(const struct exception_table_entry *fixup,
+				struct pt_regs *regs)
 {
 	if (static_cpu_has(X86_BUG_NULL_SEG))
 		asm volatile ("mov %0, %%fs" : : "rm" (__USER_DS));
 	asm volatile ("mov %0, %%fs" : : "rm" (0));
-	return ex_handler_default(fixup, regs, trapnr, error_code, fault_addr);
+	return ex_handler_default(fixup, regs);
 }
-EXPORT_SYMBOL(ex_handler_clear_fs);
 
-enum handler_type ex_get_fault_handler_type(unsigned long ip)
+static bool ex_handler_imm_reg(const struct exception_table_entry *fixup,
+			       struct pt_regs *regs, int reg, int imm)
 {
-	const struct exception_table_entry *e;
-	ex_handler_t handler;
+	*pt_regs_nr(regs, reg) = (long)imm;
+	return ex_handler_default(fixup, regs);
+}
 
-	e = search_exception_tables(ip);
-	if (!e)
-		return EX_HANDLER_NONE;
-	handler = ex_fixup_handler(e);
-	if (handler == ex_handler_fault)
-		return EX_HANDLER_FAULT;
-	else if (handler == ex_handler_uaccess || handler == ex_handler_copy)
-		return EX_HANDLER_UACCESS;
-	else
-		return EX_HANDLER_OTHER;
+int ex_get_fixup_type(unsigned long ip)
+{
+	const struct exception_table_entry *e = search_exception_tables(ip);
+
+	return e ? FIELD_GET(EX_DATA_TYPE_MASK, e->data) : EX_TYPE_NONE;
 }
 
 int fixup_exception(struct pt_regs *regs, int trapnr, unsigned long error_code,
 		    unsigned long fault_addr)
 {
 	const struct exception_table_entry *e;
-	ex_handler_t handler;
+	int type, reg, imm;
 
 #ifdef CONFIG_PNPBIOS
 	if (unlikely(SEGMENT_IS_PNP_CODE(regs->cs))) {
@@ -179,8 +158,48 @@
 	if (!e)
 		return 0;
 
-	handler = ex_fixup_handler(e);
-	return handler(e, regs, trapnr, error_code, fault_addr);
+	type = FIELD_GET(EX_DATA_TYPE_MASK, e->data);
+	reg  = FIELD_GET(EX_DATA_REG_MASK,  e->data);
+	imm  = FIELD_GET(EX_DATA_IMM_MASK,  e->data);
+
+	switch (type) {
+	case EX_TYPE_DEFAULT:
+	case EX_TYPE_DEFAULT_MCE_SAFE:
+		return ex_handler_default(e, regs);
+	case EX_TYPE_FAULT:
+	case EX_TYPE_FAULT_MCE_SAFE:
+		return ex_handler_fault(e, regs, trapnr);
+	case EX_TYPE_UACCESS:
+		return ex_handler_uaccess(e, regs, trapnr);
+	case EX_TYPE_COPY:
+		return ex_handler_copy(e, regs, trapnr);
+	case EX_TYPE_CLEAR_FS:
+		return ex_handler_clear_fs(e, regs);
+	case EX_TYPE_FPU_RESTORE:
+		return ex_handler_fprestore(e, regs);
+	case EX_TYPE_BPF:
+		return ex_handler_bpf(e, regs);
+	case EX_TYPE_WRMSR:
+		return ex_handler_msr(e, regs, true, false, reg);
+	case EX_TYPE_RDMSR:
+		return ex_handler_msr(e, regs, false, false, reg);
+	case EX_TYPE_WRMSR_SAFE:
+		return ex_handler_msr(e, regs, true, true, reg);
+	case EX_TYPE_RDMSR_SAFE:
+		return ex_handler_msr(e, regs, false, true, reg);
+	case EX_TYPE_WRMSR_IN_MCE:
+		ex_handler_msr_mce(regs, true);
+		break;
+	case EX_TYPE_RDMSR_IN_MCE:
+		ex_handler_msr_mce(regs, false);
+		break;
+	case EX_TYPE_POP_REG:
+		regs->sp += sizeof(long);
+		fallthrough;
+	case EX_TYPE_IMM_REG:
+		return ex_handler_imm_reg(e, regs, reg, imm);
+	}
+	BUG();
 }
 
 extern unsigned int early_recursion_flag;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/fault.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/fault.c
@@ -32,6 +32,7 @@
 #include <asm/pgtable_areas.h>		/* VMALLOC_START, ...		*/
 #include <asm/kvm_para.h>		/* kvm_handle_async_pf		*/
 #include <asm/vdso.h>			/* fixup_vdso_exception()	*/
+#include <asm/irq_stack.h>
 
 #define CREATE_TRACE_POINTS
 #include <asm/trace/exceptions.h>
@@ -631,6 +632,9 @@
 page_fault_oops(struct pt_regs *regs, unsigned long error_code,
 		unsigned long address)
 {
+#ifdef CONFIG_VMAP_STACK
+	struct stack_info info;
+#endif
 	unsigned long flags;
 	int sig;
 
@@ -649,9 +653,7 @@
 	 * that we're in vmalloc space to avoid this.
 	 */
 	if (is_vmalloc_addr((void *)address) &&
-	    (((unsigned long)current->stack - 1 - address < PAGE_SIZE) ||
-	     address - ((unsigned long)current->stack + THREAD_SIZE) < PAGE_SIZE)) {
-		unsigned long stack = __this_cpu_ist_top_va(DF) - sizeof(void *);
+	    get_stack_guard_info((void *)address, &info)) {
 		/*
 		 * We're likely to be running with very little stack space
 		 * left.  It's plausible that we'd hit this condition but
@@ -662,13 +664,11 @@
 		 * and then double-fault, though, because we're likely to
 		 * break the console driver and lose most of the stack dump.
 		 */
-		asm volatile ("movq %[stack], %%rsp\n\t"
-			      "call handle_stack_overflow\n\t"
-			      "1: jmp 1b"
-			      : ASM_CALL_CONSTRAINT
-			      : "D" ("kernel stack overflow (page fault)"),
-				"S" (regs), "d" (address),
-				[stack] "rm" (stack));
+		call_on_stack(__this_cpu_ist_top_va(DF) - sizeof(void*),
+			      handle_stack_overflow,
+			      ASM_CALL_ARG3,
+			      , [arg1] "r" (regs), [arg2] "r" (address), [arg3] "r" (&info));
+
 		unreachable();
 	}
 #endif
@@ -716,39 +716,8 @@
 	WARN_ON_ONCE(user_mode(regs));
 
 	/* Are we prepared to handle this kernel fault? */
-	if (fixup_exception(regs, X86_TRAP_PF, error_code, address)) {
-		/*
-		 * Any interrupt that takes a fault gets the fixup. This makes
-		 * the below recursive fault logic only apply to a faults from
-		 * task context.
-		 */
-		if (in_interrupt())
-			return;
-
-		/*
-		 * Per the above we're !in_interrupt(), aka. task context.
-		 *
-		 * In this case we need to make sure we're not recursively
-		 * faulting through the emulate_vsyscall() logic.
-		 */
-		if (current->thread.sig_on_uaccess_err && signal) {
-			sanitize_error_code(address, &error_code);
-
-			set_signal_archinfo(address, error_code);
-
-			if (si_code == SEGV_PKUERR) {
-				force_sig_pkuerr((void __user *)address, pkey);
-			} else {
-				/* XXX: hwpoison faults will set the wrong code. */
-				force_sig_fault(signal, si_code, (void __user *)address);
-			}
-		}
-
-		/*
-		 * Barring that, we can do the fixup and be happy.
-		 */
+	if (fixup_exception(regs, X86_TRAP_PF, error_code, address))
 		return;
-	}
 
 	/*
 	 * AMD erratum #91 manifests as a spurious page fault on a PREFETCH
@@ -787,15 +756,6 @@
 	show_opcodes(regs, loglvl);
 }
 
-/*
- * The (legacy) vsyscall page is the long page in the kernel portion
- * of the address space that has user-accessible permissions.
- */
-static bool is_vsyscall_vaddr(unsigned long vaddr)
-{
-	return unlikely((vaddr & PAGE_MASK) == VSYSCALL_ADDR);
-}
-
 static void
 __bad_area_nosemaphore(struct pt_regs *regs, unsigned long error_code,
 		       unsigned long address, u32 pkey, int si_code)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/init.c
@@ -9,6 +9,7 @@
 #include <linux/sched/task.h>
 
 #include <asm/set_memory.h>
+#include <asm/cpu_device_id.h>
 #include <asm/e820/api.h>
 #include <asm/init.h>
 #include <asm/page.h>
@@ -26,6 +27,7 @@
 #include <asm/pti.h>
 #include <asm/text-patching.h>
 #include <asm/memtype.h>
+#include <asm/paravirt.h>
 
 /*
  * We need to define the tracepoints somewhere, and tlb.c
@@ -78,10 +80,20 @@
 	[__pte2cm_idx(_PAGE_PWT | _PAGE_PCD | _PAGE_PAT)] = _PAGE_CACHE_MODE_UC,
 };
 
-/* Check that the write-protect PAT entry is set for write-protect */
+/*
+ * Check that the write-protect PAT entry is set for write-protect.
+ * To do this without making assumptions how PAT has been set up (Xen has
+ * another layout than the kernel), translate the _PAGE_CACHE_MODE_WP cache
+ * mode via the __cachemode2pte_tbl[] into protection bits (those protection
+ * bits will select a cache mode of WP or better), and then translate the
+ * protection bits back into the cache mode using __pte2cm_idx() and the
+ * __pte2cachemode_tbl[] array. This will return the really used cache mode.
+ */
 bool x86_has_pat_wp(void)
 {
-	return __pte2cachemode_tbl[_PAGE_CACHE_MODE_WP] == _PAGE_CACHE_MODE_WP;
+	uint16_t prot = __cachemode2pte_tbl[_PAGE_CACHE_MODE_WP];
+
+	return __pte2cachemode_tbl[__pte2cm_idx(prot)] == _PAGE_CACHE_MODE_WP;
 }
 
 enum page_cache_mode pgprot2cachemode(pgprot_t pgprot)
@@ -251,14 +263,39 @@
 	}
 }
 
+/*
+ * INVLPG may not properly flush Global entries on
+ * these CPUs.  New microcode fixes the issue.
+ */
+static const struct x86_cpu_id invlpg_miss_ids[] = {
+	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE,      0x2e),
+	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L,    0x42c),
+	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_N,    0x11),
+	X86_MATCH_INTEL_FAM6_MODEL(RAPTORLAKE,     0x118),
+	X86_MATCH_INTEL_FAM6_MODEL(RAPTORLAKE_P,   0x4117),
+	X86_MATCH_INTEL_FAM6_MODEL(RAPTORLAKE_S,   0x2e),
+	{}
+};
+
 static void setup_pcid(void)
 {
+	const struct x86_cpu_id *invlpg_miss_match;
+
 	if (!IS_ENABLED(CONFIG_X86_64))
 		return;
 
 	if (!boot_cpu_has(X86_FEATURE_PCID))
 		return;
 
+	invlpg_miss_match = x86_match_cpu(invlpg_miss_ids);
+
+	if (invlpg_miss_match &&
+	    boot_cpu_data.microcode < invlpg_miss_match->driver_data) {
+		pr_info("Incomplete global flushes, disabling PCID");
+		setup_clear_cpu_cap(X86_FEATURE_PCID);
+		return;
+	}
+
 	if (boot_cpu_has(X86_FEATURE_PGE)) {
 		/*
 		 * This can't be cr4_set_bits_and_update_boot() -- the
@@ -787,9 +824,12 @@
 	spinlock_t *ptl;
 	pte_t *ptep;
 
-	poking_mm = copy_init_mm();
+	poking_mm = mm_alloc();
 	BUG_ON(!poking_mm);
 
+	/* Xen PV guests need the PGD to be pinned. */
+	paravirt_arch_dup_mmap(NULL, poking_mm);
+
 	/*
 	 * Randomize the poking address, but make sure that the following page
 	 * will be mapped at the same PMD. We need 2 pages, so find space for 3,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/init_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/init_64.c
@@ -646,7 +646,7 @@
 			pages++;
 			spin_lock(&init_mm.page_table_lock);
 
-			prot = __pgprot(pgprot_val(prot) | __PAGE_KERNEL_LARGE);
+			prot = __pgprot(pgprot_val(prot) | _PAGE_PSE);
 
 			set_pte_init((pte_t *)pud,
 				     pfn_pte((paddr & PUD_MASK) >> PAGE_SHIFT,
@@ -902,6 +902,8 @@
 
 static void __meminit vmemmap_use_new_sub_pmd(unsigned long start, unsigned long end)
 {
+	const unsigned long page = ALIGN_DOWN(start, PMD_SIZE);
+
 	vmemmap_flush_unused_pmd();
 
 	/*
@@ -914,8 +916,7 @@
 	 * Mark with PAGE_UNUSED the unused parts of the new memmap range
 	 */
 	if (!IS_ALIGNED(start, PMD_SIZE))
-		memset((void *)start, PAGE_UNUSED,
-			start - ALIGN_DOWN(start, PMD_SIZE));
+		memset((void *)page, PAGE_UNUSED, start - page);
 
 	/*
 	 * We want to avoid memset(PAGE_UNUSED) when populating the vmemmap of
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/ioremap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/ioremap.c
@@ -216,9 +216,15 @@
 	 * Mappings have to be page-aligned
 	 */
 	offset = phys_addr & ~PAGE_MASK;
-	phys_addr &= PHYSICAL_PAGE_MASK;
+	phys_addr &= PAGE_MASK;
 	size = PAGE_ALIGN(last_addr+1) - phys_addr;
 
+	/*
+	 * Mask out any bits not part of the actual physical
+	 * address, like memory encryption bits.
+	 */
+	phys_addr &= PHYSICAL_PAGE_MASK;
+
 	retval = memtype_reserve(phys_addr, (u64)phys_addr + size,
 						pcm, &new_pcm);
 	if (retval) {
@@ -614,6 +620,7 @@
 static bool memremap_is_setup_data(resource_size_t phys_addr,
 				   unsigned long size)
 {
+	struct setup_indirect *indirect;
 	struct setup_data *data;
 	u64 paddr, paddr_next;
 
@@ -626,19 +633,35 @@
 
 		data = memremap(paddr, sizeof(*data),
 				MEMREMAP_WB | MEMREMAP_DEC);
+		if (!data) {
+			pr_warn("failed to memremap setup_data entry\n");
+			return false;
+		}
 
 		paddr_next = data->next;
 		len = data->len;
 
-		if ((phys_addr > paddr) && (phys_addr < (paddr + len))) {
+		if ((phys_addr > paddr) &&
+		    (phys_addr < (paddr + sizeof(struct setup_data) + len))) {
 			memunmap(data);
 			return true;
 		}
 
-		if (data->type == SETUP_INDIRECT &&
-		    ((struct setup_indirect *)data->data)->type != SETUP_INDIRECT) {
-			paddr = ((struct setup_indirect *)data->data)->addr;
-			len = ((struct setup_indirect *)data->data)->len;
+		if (data->type == SETUP_INDIRECT) {
+			memunmap(data);
+			data = memremap(paddr, sizeof(*data) + len,
+					MEMREMAP_WB | MEMREMAP_DEC);
+			if (!data) {
+				pr_warn("failed to memremap indirect setup_data\n");
+				return false;
+			}
+
+			indirect = (struct setup_indirect *)data->data;
+
+			if (indirect->type != SETUP_INDIRECT) {
+				paddr = indirect->addr;
+				len = indirect->len;
+			}
 		}
 
 		memunmap(data);
@@ -659,22 +682,52 @@
 static bool __init early_memremap_is_setup_data(resource_size_t phys_addr,
 						unsigned long size)
 {
+	struct setup_indirect *indirect;
 	struct setup_data *data;
 	u64 paddr, paddr_next;
 
 	paddr = boot_params.hdr.setup_data;
 	while (paddr) {
-		unsigned int len;
+		unsigned int len, size;
 
 		if (phys_addr == paddr)
 			return true;
 
 		data = early_memremap_decrypted(paddr, sizeof(*data));
+		if (!data) {
+			pr_warn("failed to early memremap setup_data entry\n");
+			return false;
+		}
+
+		size = sizeof(*data);
 
 		paddr_next = data->next;
 		len = data->len;
 
-		early_memunmap(data, sizeof(*data));
+		if ((phys_addr > paddr) &&
+		    (phys_addr < (paddr + sizeof(struct setup_data) + len))) {
+			early_memunmap(data, sizeof(*data));
+			return true;
+		}
+
+		if (data->type == SETUP_INDIRECT) {
+			size += len;
+			early_memunmap(data, sizeof(*data));
+			data = early_memremap_decrypted(paddr, size);
+			if (!data) {
+				pr_warn("failed to early memremap indirect setup_data\n");
+				return false;
+			}
+
+			indirect = (struct setup_indirect *)data->data;
+
+			if (indirect->type != SETUP_INDIRECT) {
+				paddr = indirect->addr;
+				len = indirect->len;
+			}
+		}
+
+		early_memunmap(data, size);
 
 		if ((phys_addr > paddr) && (phys_addr < (paddr + len)))
 			return true;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/kasan_init_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/kasan_init_64.c
@@ -316,6 +316,18 @@
 	kasan_map_early_shadow(init_top_pgt);
 }
 
+void __init kasan_populate_shadow_for_vaddr(void *va, size_t size, int nid)
+{
+	unsigned long shadow_start, shadow_end;
+
+	shadow_start = (unsigned long)kasan_mem_to_shadow(va);
+	shadow_start = round_down(shadow_start, PAGE_SIZE);
+	shadow_end = (unsigned long)kasan_mem_to_shadow(va + size);
+	shadow_end = round_up(shadow_end, PAGE_SIZE);
+
+	kasan_populate_shadow(shadow_start, shadow_end, nid);
+}
+
 void __init kasan_init(void)
 {
 	int i;
@@ -393,9 +405,6 @@
 		kasan_mem_to_shadow((void *)VMALLOC_END + 1),
 		shadow_cpu_entry_begin);
 
-	kasan_populate_shadow((unsigned long)shadow_cpu_entry_begin,
-			      (unsigned long)shadow_cpu_entry_end, 0);
-
 	kasan_populate_early_shadow(shadow_cpu_entry_end,
 			kasan_mem_to_shadow((void *)__START_KERNEL_map));
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/kaslr.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/kaslr.c
@@ -172,10 +172,10 @@
 		set_p4d(p4d_tramp,
 			__p4d(_KERNPG_TABLE | __pa(pud_page_tramp)));
 
-		set_pgd(&trampoline_pgd_entry,
-			__pgd(_KERNPG_TABLE | __pa(p4d_page_tramp)));
+		trampoline_pgd_entry =
+			__pgd(_KERNPG_TABLE | __pa(p4d_page_tramp));
 	} else {
-		set_pgd(&trampoline_pgd_entry,
-			__pgd(_KERNPG_TABLE | __pa(pud_page_tramp)));
+		trampoline_pgd_entry =
+			__pgd(_KERNPG_TABLE | __pa(pud_page_tramp));
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/maccess.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/maccess.c
@@ -3,23 +3,37 @@
 #include <linux/uaccess.h>
 #include <linux/kernel.h>
 
-#ifdef CONFIG_X86_64
-static __always_inline u64 canonical_address(u64 vaddr, u8 vaddr_bits)
-{
-	return ((s64)vaddr << (64 - vaddr_bits)) >> (64 - vaddr_bits);
-}
+#include <asm/vsyscall.h>
 
+#ifdef CONFIG_X86_64
 bool copy_from_kernel_nofault_allowed(const void *unsafe_src, size_t size)
 {
 	unsigned long vaddr = (unsigned long)unsafe_src;
 
 	/*
-	 * Range covering the highest possible canonical userspace address
-	 * as well as non-canonical address range. For the canonical range
-	 * we also need to include the userspace guard page.
+	 * Do not allow userspace addresses.  This disallows
+	 * normal userspace and the userspace guard page:
 	 */
-	return vaddr >= TASK_SIZE_MAX + PAGE_SIZE &&
-	       canonical_address(vaddr, boot_cpu_data.x86_virt_bits) == vaddr;
+	if (vaddr < TASK_SIZE_MAX + PAGE_SIZE)
+		return false;
+
+	/*
+	 * Reading from the vsyscall page may cause an unhandled fault in
+	 * certain cases.  Though it is at an address above TASK_SIZE_MAX, it is
+	 * usually considered as a user space address.
+	 */
+	if (is_vsyscall_vaddr(vaddr))
+		return false;
+
+	/*
+	 * Allow everything during early boot before 'x86_virt_bits'
+	 * is initialized.  Needed for instruction decoding in early
+	 * exception handlers.
+	 */
+	if (!boot_cpu_data.x86_virt_bits)
+		return true;
+
+	return __is_canonical_address(vaddr, boot_cpu_data.x86_virt_bits);
 }
 #else
 bool copy_from_kernel_nofault_allowed(const void *unsafe_src, size_t size)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/mem_encrypt_amd.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/mem_encrypt_amd.c
@@ -0,0 +1,502 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * AMD Memory Encryption Support
+ *
+ * Copyright (C) 2016 Advanced Micro Devices, Inc.
+ *
+ * Author: Tom Lendacky <thomas.lendacky@amd.com>
+ */
+
+#define DISABLE_BRANCH_PROFILING
+
+#include <linux/linkage.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/dma-direct.h>
+#include <linux/swiotlb.h>
+#include <linux/mem_encrypt.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/dma-mapping.h>
+#include <linux/virtio_config.h>
+#include <linux/cc_platform.h>
+
+#include <asm/tlbflush.h>
+#include <asm/fixmap.h>
+#include <asm/setup.h>
+#include <asm/bootparam.h>
+#include <asm/set_memory.h>
+#include <asm/cacheflush.h>
+#include <asm/processor-flags.h>
+#include <asm/msr.h>
+#include <asm/cmdline.h>
+#include <asm/ia32.h>
+
+#include "mm_internal.h"
+
+/*
+ * Since SME related variables are set early in the boot process they must
+ * reside in the .data section so as not to be zeroed out when the .bss
+ * section is later cleared.
+ */
+u64 sme_me_mask __section(".data") = 0;
+u64 sev_status __section(".data") = 0;
+u64 sev_check_data __section(".data") = 0;
+EXPORT_SYMBOL(sme_me_mask);
+DEFINE_STATIC_KEY_FALSE(sev_enable_key);
+EXPORT_SYMBOL_GPL(sev_enable_key);
+
+/* Buffer used for early in-place encryption by BSP, no locking needed */
+static char sme_early_buffer[PAGE_SIZE] __initdata __aligned(PAGE_SIZE);
+
+/*
+ * This routine does not change the underlying encryption setting of the
+ * page(s) that map this memory. It assumes that eventually the memory is
+ * meant to be accessed as either encrypted or decrypted but the contents
+ * are currently not in the desired state.
+ *
+ * This routine follows the steps outlined in the AMD64 Architecture
+ * Programmer's Manual Volume 2, Section 7.10.8 Encrypt-in-Place.
+ */
+static void __init __sme_early_enc_dec(resource_size_t paddr,
+				       unsigned long size, bool enc)
+{
+	void *src, *dst;
+	size_t len;
+
+	if (!sme_me_mask)
+		return;
+
+	wbinvd();
+
+	/*
+	 * There are limited number of early mapping slots, so map (at most)
+	 * one page at time.
+	 */
+	while (size) {
+		len = min_t(size_t, sizeof(sme_early_buffer), size);
+
+		/*
+		 * Create mappings for the current and desired format of
+		 * the memory. Use a write-protected mapping for the source.
+		 */
+		src = enc ? early_memremap_decrypted_wp(paddr, len) :
+			    early_memremap_encrypted_wp(paddr, len);
+
+		dst = enc ? early_memremap_encrypted(paddr, len) :
+			    early_memremap_decrypted(paddr, len);
+
+		/*
+		 * If a mapping can't be obtained to perform the operation,
+		 * then eventual access of that area in the desired mode
+		 * will cause a crash.
+		 */
+		BUG_ON(!src || !dst);
+
+		/*
+		 * Use a temporary buffer, of cache-line multiple size, to
+		 * avoid data corruption as documented in the APM.
+		 */
+		memcpy(sme_early_buffer, src, len);
+		memcpy(dst, sme_early_buffer, len);
+
+		early_memunmap(dst, len);
+		early_memunmap(src, len);
+
+		paddr += len;
+		size -= len;
+	}
+}
+
+void __init sme_early_encrypt(resource_size_t paddr, unsigned long size)
+{
+	__sme_early_enc_dec(paddr, size, true);
+}
+
+void __init sme_early_decrypt(resource_size_t paddr, unsigned long size)
+{
+	__sme_early_enc_dec(paddr, size, false);
+}
+
+static void __init __sme_early_map_unmap_mem(void *vaddr, unsigned long size,
+					     bool map)
+{
+	unsigned long paddr = (unsigned long)vaddr - __PAGE_OFFSET;
+	pmdval_t pmd_flags, pmd;
+
+	/* Use early_pmd_flags but remove the encryption mask */
+	pmd_flags = __sme_clr(early_pmd_flags);
+
+	do {
+		pmd = map ? (paddr & PMD_MASK) + pmd_flags : 0;
+		__early_make_pgtable((unsigned long)vaddr, pmd);
+
+		vaddr += PMD_SIZE;
+		paddr += PMD_SIZE;
+		size = (size <= PMD_SIZE) ? 0 : size - PMD_SIZE;
+	} while (size);
+
+	flush_tlb_local();
+}
+
+void __init sme_unmap_bootdata(char *real_mode_data)
+{
+	struct boot_params *boot_data;
+	unsigned long cmdline_paddr;
+
+	if (!sme_active())
+		return;
+
+	/* Get the command line address before unmapping the real_mode_data */
+	boot_data = (struct boot_params *)real_mode_data;
+	cmdline_paddr = boot_data->hdr.cmd_line_ptr | ((u64)boot_data->ext_cmd_line_ptr << 32);
+
+	__sme_early_map_unmap_mem(real_mode_data, sizeof(boot_params), false);
+
+	if (!cmdline_paddr)
+		return;
+
+	__sme_early_map_unmap_mem(__va(cmdline_paddr), COMMAND_LINE_SIZE, false);
+}
+
+void __init sme_map_bootdata(char *real_mode_data)
+{
+	struct boot_params *boot_data;
+	unsigned long cmdline_paddr;
+
+	if (!sme_active())
+		return;
+
+	__sme_early_map_unmap_mem(real_mode_data, sizeof(boot_params), true);
+
+	/* Get the command line address after mapping the real_mode_data */
+	boot_data = (struct boot_params *)real_mode_data;
+	cmdline_paddr = boot_data->hdr.cmd_line_ptr | ((u64)boot_data->ext_cmd_line_ptr << 32);
+
+	if (!cmdline_paddr)
+		return;
+
+	__sme_early_map_unmap_mem(__va(cmdline_paddr), COMMAND_LINE_SIZE, true);
+}
+
+void __init sme_early_init(void)
+{
+	unsigned int i;
+
+	if (!sme_me_mask)
+		return;
+
+	early_pmd_flags = __sme_set(early_pmd_flags);
+
+	__supported_pte_mask = __sme_set(__supported_pte_mask);
+
+	/* Update the protection map with memory encryption mask */
+	for (i = 0; i < ARRAY_SIZE(protection_map); i++)
+		protection_map[i] = pgprot_encrypted(protection_map[i]);
+
+	if (sev_active())
+		swiotlb_force = SWIOTLB_FORCE;
+
+	/*
+	 * The VMM is capable of injecting interrupt 0x80 and triggering the
+	 * compatibility syscall path.
+	 *
+	 * By default, the 32-bit emulation is disabled in order to ensure
+	 * the safety of the VM.
+	 */
+	if (sev_status & MSR_AMD64_SEV_ENABLED)
+		ia32_disable();
+}
+
+void __init sev_setup_arch(void)
+{
+	phys_addr_t total_mem = memblock_phys_mem_size();
+	unsigned long size;
+
+	if (!sev_active())
+		return;
+
+	/*
+	 * For SEV, all DMA has to occur via shared/unencrypted pages.
+	 * SEV uses SWIOTLB to make this happen without changing device
+	 * drivers. However, depending on the workload being run, the
+	 * default 64MB of SWIOTLB may not be enough and SWIOTLB may
+	 * run out of buffers for DMA, resulting in I/O errors and/or
+	 * performance degradation especially with high I/O workloads.
+	 *
+	 * Adjust the default size of SWIOTLB for SEV guests using
+	 * a percentage of guest memory for SWIOTLB buffers.
+	 * Also, as the SWIOTLB bounce buffer memory is allocated
+	 * from low memory, ensure that the adjusted size is within
+	 * the limits of low available memory.
+	 *
+	 * The percentage of guest memory used here for SWIOTLB buffers
+	 * is more of an approximation of the static adjustment which
+	 * 64MB for <1G, and ~128M to 256M for 1G-to-4G, i.e., the 6%
+	 */
+	size = total_mem * 6 / 100;
+	size = clamp_val(size, IO_TLB_DEFAULT_SIZE, SZ_1G);
+	swiotlb_adjust_size(size);
+}
+
+static void __init __set_clr_pte_enc(pte_t *kpte, int level, bool enc)
+{
+	pgprot_t old_prot, new_prot;
+	unsigned long pfn, pa, size;
+	pte_t new_pte;
+
+	switch (level) {
+	case PG_LEVEL_4K:
+		pfn = pte_pfn(*kpte);
+		old_prot = pte_pgprot(*kpte);
+		break;
+	case PG_LEVEL_2M:
+		pfn = pmd_pfn(*(pmd_t *)kpte);
+		old_prot = pmd_pgprot(*(pmd_t *)kpte);
+		break;
+	case PG_LEVEL_1G:
+		pfn = pud_pfn(*(pud_t *)kpte);
+		old_prot = pud_pgprot(*(pud_t *)kpte);
+		break;
+	default:
+		return;
+	}
+
+	new_prot = old_prot;
+	if (enc)
+		pgprot_val(new_prot) |= _PAGE_ENC;
+	else
+		pgprot_val(new_prot) &= ~_PAGE_ENC;
+
+	/* If prot is same then do nothing. */
+	if (pgprot_val(old_prot) == pgprot_val(new_prot))
+		return;
+
+	pa = pfn << PAGE_SHIFT;
+	size = page_level_size(level);
+
+	/*
+	 * We are going to perform in-place en-/decryption and change the
+	 * physical page attribute from C=1 to C=0 or vice versa. Flush the
+	 * caches to ensure that data gets accessed with the correct C-bit.
+	 */
+	clflush_cache_range(__va(pa), size);
+
+	/* Encrypt/decrypt the contents in-place */
+	if (enc)
+		sme_early_encrypt(pa, size);
+	else
+		sme_early_decrypt(pa, size);
+
+	/* Change the page encryption mask. */
+	new_pte = pfn_pte(pfn, new_prot);
+	set_pte_atomic(kpte, new_pte);
+}
+
+static int __init early_set_memory_enc_dec(unsigned long vaddr,
+					   unsigned long size, bool enc)
+{
+	unsigned long vaddr_end, vaddr_next;
+	unsigned long psize, pmask;
+	int split_page_size_mask;
+	int level, ret;
+	pte_t *kpte;
+
+	vaddr_next = vaddr;
+	vaddr_end = vaddr + size;
+
+	for (; vaddr < vaddr_end; vaddr = vaddr_next) {
+		kpte = lookup_address(vaddr, &level);
+		if (!kpte || pte_none(*kpte)) {
+			ret = 1;
+			goto out;
+		}
+
+		if (level == PG_LEVEL_4K) {
+			__set_clr_pte_enc(kpte, level, enc);
+			vaddr_next = (vaddr & PAGE_MASK) + PAGE_SIZE;
+			continue;
+		}
+
+		psize = page_level_size(level);
+		pmask = page_level_mask(level);
+
+		/*
+		 * Check whether we can change the large page in one go.
+		 * We request a split when the address is not aligned and
+		 * the number of pages to set/clear encryption bit is smaller
+		 * than the number of pages in the large page.
+		 */
+		if (vaddr == (vaddr & pmask) &&
+		    ((vaddr_end - vaddr) >= psize)) {
+			__set_clr_pte_enc(kpte, level, enc);
+			vaddr_next = (vaddr & pmask) + psize;
+			continue;
+		}
+
+		/*
+		 * The virtual address is part of a larger page, create the next
+		 * level page table mapping (4K or 2M). If it is part of a 2M
+		 * page then we request a split of the large page into 4K
+		 * chunks. A 1GB large page is split into 2M pages, resp.
+		 */
+		if (level == PG_LEVEL_2M)
+			split_page_size_mask = 0;
+		else
+			split_page_size_mask = 1 << PG_LEVEL_2M;
+
+		/*
+		 * kernel_physical_mapping_change() does not flush the TLBs, so
+		 * a TLB flush is required after we exit from the for loop.
+		 */
+		kernel_physical_mapping_change(__pa(vaddr & pmask),
+					       __pa((vaddr_end & pmask) + psize),
+					       split_page_size_mask);
+	}
+
+	ret = 0;
+
+out:
+	__flush_tlb_all();
+	return ret;
+}
+
+int __init early_set_memory_decrypted(unsigned long vaddr, unsigned long size)
+{
+	return early_set_memory_enc_dec(vaddr, size, false);
+}
+
+int __init early_set_memory_encrypted(unsigned long vaddr, unsigned long size)
+{
+	return early_set_memory_enc_dec(vaddr, size, true);
+}
+
+/*
+ * SME and SEV are very similar but they are not the same, so there are
+ * times that the kernel will need to distinguish between SME and SEV. The
+ * sme_active() and sev_active() functions are used for this.  When a
+ * distinction isn't needed, the mem_encrypt_active() function can be used.
+ *
+ * The trampoline code is a good example for this requirement.  Before
+ * paging is activated, SME will access all memory as decrypted, but SEV
+ * will access all memory as encrypted.  So, when APs are being brought
+ * up under SME the trampoline area cannot be encrypted, whereas under SEV
+ * the trampoline area must be encrypted.
+ */
+bool sev_active(void)
+{
+	return sev_status & MSR_AMD64_SEV_ENABLED;
+}
+
+bool sme_active(void)
+{
+	return sme_me_mask && !sev_active();
+}
+EXPORT_SYMBOL_GPL(sev_active);
+
+/* Needs to be called from non-instrumentable code */
+bool noinstr sev_es_active(void)
+{
+	return sev_status & MSR_AMD64_SEV_ES_ENABLED;
+}
+
+/* Override for DMA direct allocation check - ARCH_HAS_FORCE_DMA_UNENCRYPTED */
+bool force_dma_unencrypted(struct device *dev)
+{
+	/*
+	 * For SEV, all DMA must be to unencrypted addresses.
+	 */
+	if (sev_active())
+		return true;
+
+	/*
+	 * For SME, all DMA must be to unencrypted addresses if the
+	 * device does not support DMA to addresses that include the
+	 * encryption mask.
+	 */
+	if (sme_active()) {
+		u64 dma_enc_mask = DMA_BIT_MASK(__ffs64(sme_me_mask));
+		u64 dma_dev_mask = min_not_zero(dev->coherent_dma_mask,
+						dev->bus_dma_limit);
+
+		if (dma_dev_mask <= dma_enc_mask)
+			return true;
+	}
+
+	return false;
+}
+
+void __init mem_encrypt_free_decrypted_mem(void)
+{
+	unsigned long vaddr, vaddr_end, npages;
+	int r;
+
+	vaddr = (unsigned long)__start_bss_decrypted_unused;
+	vaddr_end = (unsigned long)__end_bss_decrypted;
+	npages = (vaddr_end - vaddr) >> PAGE_SHIFT;
+
+	/*
+	 * The unused memory range was mapped decrypted, change the encryption
+	 * attribute from decrypted to encrypted before freeing it.
+	 */
+	if (mem_encrypt_active()) {
+		r = set_memory_encrypted(vaddr, npages);
+		if (r) {
+			pr_warn("failed to free unused decrypted pages\n");
+			return;
+		}
+	}
+
+	free_init_pages("unused decrypted", vaddr, vaddr_end);
+}
+
+static void print_mem_encrypt_feature_info(void)
+{
+	pr_info("AMD Memory Encryption Features active:");
+
+	/* Secure Memory Encryption */
+	if (sme_active()) {
+		/*
+		 * SME is mutually exclusive with any of the SEV
+		 * features below.
+		 */
+		pr_cont(" SME\n");
+		return;
+	}
+
+	/* Secure Encrypted Virtualization */
+	if (sev_active())
+		pr_cont(" SEV");
+
+	/* Encrypted Register State */
+	if (sev_es_active())
+		pr_cont(" SEV-ES");
+
+	pr_cont("\n");
+}
+
+/* Architecture __weak replacement functions */
+void __init mem_encrypt_init(void)
+{
+	if (!sme_me_mask)
+		return;
+
+	/* Call into SWIOTLB to update the SWIOTLB DMA buffers */
+	swiotlb_update_mem_attributes();
+
+	/*
+	 * With SEV, we need to unroll the rep string I/O instructions,
+	 * but SEV-ES supports them through the #VC handler.
+	 */
+	if (sev_active() && !sev_es_active())
+		static_branch_enable(&sev_enable_key);
+
+	print_mem_encrypt_feature_info();
+}
+
+int arch_has_restricted_virtio_memory_access(void)
+{
+	return sev_active();
+}
+EXPORT_SYMBOL_GPL(arch_has_restricted_virtio_memory_access);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/mem_encrypt_boot.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/mem_encrypt_boot.S
@@ -65,7 +65,10 @@
 	movq	%rbp, %rsp		/* Restore original stack pointer */
 	pop	%rbp
 
+	/* Offset to __x86_return_thunk would be wrong here */
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 SYM_FUNC_END(sme_encrypt_execute)
 
 SYM_FUNC_START(__enc_copy)
@@ -151,6 +154,9 @@
 	pop	%r12
 	pop	%r15
 
+	/* Offset to __x86_return_thunk would be wrong here */
+	ANNOTATE_UNRET_SAFE
 	ret
+	int3
 .L__enc_copy_end:
 SYM_FUNC_END(__enc_copy)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/mem_encrypt_identity.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/mem_encrypt_identity.c
@@ -27,6 +27,15 @@
 #undef CONFIG_PARAVIRT_XXL
 #undef CONFIG_PARAVIRT_SPINLOCKS
 
+/*
+ * This code runs before CPU feature bits are set. By default, the
+ * pgtable_l5_enabled() function uses bit X86_FEATURE_LA57 to determine if
+ * 5-level paging is active, so that won't work here. USE_EARLY_PGTABLE_L5
+ * is provided to handle this situation and, instead, use a variable that
+ * has been set by the early boot code.
+ */
+#define USE_EARLY_PGTABLE_L5
+
 #include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/mem_encrypt.h>
@@ -576,7 +585,8 @@
 	cmdline_ptr = (const char *)((u64)bp->hdr.cmd_line_ptr |
 				     ((u64)bp->ext_cmd_line_ptr << 32));
 
-	cmdline_find_option(cmdline_ptr, cmdline_arg, buffer, sizeof(buffer));
+	if (cmdline_find_option(cmdline_ptr, cmdline_arg, buffer, sizeof(buffer)) < 0)
+		return;
 
 	if (!strncmp(buffer, cmdline_on, sizeof(buffer)))
 		sme_me_mask = me_mask;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/numa.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/numa.c
@@ -601,13 +601,6 @@
 		if (start >= end)
 			continue;
 
-		/*
-		 * Don't confuse VM with a node that doesn't have the
-		 * minimum amount of memory:
-		 */
-		if (end && (end - start) < NODE_MIN_SIZE)
-			continue;
-
 		alloc_node_data(nid);
 	}
 
@@ -860,7 +853,7 @@
 		return;
 	}
 	mask = node_to_cpumask_map[node];
-	if (!mask) {
+	if (!cpumask_available(mask)) {
 		pr_err("node_to_cpumask_map[%i] NULL\n", node);
 		dump_stack();
 		return;
@@ -906,7 +899,7 @@
 		dump_stack();
 		return cpu_none_mask;
 	}
-	if (node_to_cpumask_map[node] == NULL) {
+	if (!cpumask_available(node_to_cpumask_map[node])) {
 		printk(KERN_WARNING
 			"cpumask_of_node(%d): no node_to_cpumask_map!\n",
 			node);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/pat/cpa-test.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/pat/cpa-test.c
@@ -183,7 +183,7 @@
 			break;
 
 		case 1:
-			err = change_page_attr_set(addrs, len[1], PAGE_CPA_TEST, 1);
+			err = change_page_attr_set(addrs, len[i], PAGE_CPA_TEST, 1);
 			break;
 
 		case 2:
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/pat/memtype.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/pat/memtype.c
@@ -101,7 +101,7 @@
 static int __init pat_debug_setup(char *str)
 {
 	pat_debug_enable = 1;
-	return 0;
+	return 1;
 }
 __setup("debugpat", pat_debug_setup);
 
@@ -989,6 +989,38 @@
 		memtype_free(paddr, paddr + size);
 }
 
+static int get_pat_info(struct vm_area_struct *vma, resource_size_t *paddr,
+		pgprot_t *pgprot)
+{
+	unsigned long prot;
+
+	VM_WARN_ON_ONCE(!(vma->vm_flags & VM_PAT));
+
+	/*
+	 * We need the starting PFN and cachemode used for track_pfn_remap()
+	 * that covered the whole VMA. For most mappings, we can obtain that
+	 * information from the page tables. For COW mappings, we might now
+	 * suddenly have anon folios mapped and follow_phys() will fail.
+	 *
+	 * Fallback to using vma->vm_pgoff, see remap_pfn_range_notrack(), to
+	 * detect the PFN. If we need the cachemode as well, we're out of luck
+	 * for now and have to fail fork().
+	 */
+	if (!follow_phys(vma, vma->vm_start, 0, &prot, paddr)) {
+		if (pgprot)
+			*pgprot = __pgprot(prot);
+		return 0;
+	}
+	if (is_cow_mapping(vma->vm_flags)) {
+		if (pgprot)
+			return -EINVAL;
+		*paddr = (resource_size_t)vma->vm_pgoff << PAGE_SHIFT;
+		return 0;
+	}
+	WARN_ON_ONCE(1);
+	return -EINVAL;
+}
+
 /*
  * track_pfn_copy is called when vma that is covering the pfnmap gets
  * copied through copy_page_range().
@@ -999,20 +1031,13 @@
 int track_pfn_copy(struct vm_area_struct *vma)
 {
 	resource_size_t paddr;
-	unsigned long prot;
 	unsigned long vma_size = vma->vm_end - vma->vm_start;
 	pgprot_t pgprot;
 
 	if (vma->vm_flags & VM_PAT) {
-		/*
-		 * reserve the whole chunk covered by vma. We need the
-		 * starting address and protection from pte.
-		 */
-		if (follow_phys(vma, vma->vm_start, 0, &prot, &paddr)) {
-			WARN_ON_ONCE(1);
+		if (get_pat_info(vma, &paddr, &pgprot))
 			return -EINVAL;
-		}
-		pgprot = __pgprot(prot);
+		/* reserve the whole chunk covered by vma. */
 		return reserve_pfn_range(paddr, vma_size, &pgprot, 1);
 	}
 
@@ -1087,7 +1112,6 @@
 		 unsigned long size)
 {
 	resource_size_t paddr;
-	unsigned long prot;
 
 	if (vma && !(vma->vm_flags & VM_PAT))
 		return;
@@ -1095,11 +1119,8 @@
 	/* free the chunk starting from pfn or the whole chunk */
 	paddr = (resource_size_t)pfn << PAGE_SHIFT;
 	if (!paddr && !size) {
-		if (follow_phys(vma, vma->vm_start, 0, &prot, &paddr)) {
-			WARN_ON_ONCE(1);
+		if (get_pat_info(vma, &paddr, NULL))
 			return;
-		}
-
 		size = vma->vm_end - vma->vm_start;
 	}
 	free_pfn_range(paddr, size);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/pti.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/pti.c
@@ -241,7 +241,7 @@
  *
  * Returns a pointer to a PTE on success, or NULL on failure.
  */
-static pte_t *pti_user_pagetable_walk_pte(unsigned long address)
+static pte_t *pti_user_pagetable_walk_pte(unsigned long address, bool late_text)
 {
 	gfp_t gfp = (GFP_KERNEL | __GFP_NOTRACK | __GFP_ZERO);
 	pmd_t *pmd;
@@ -251,10 +251,15 @@
 	if (!pmd)
 		return NULL;
 
-	/* We can't do anything sensible if we hit a large mapping. */
+	/* Large PMD mapping found */
 	if (pmd_large(*pmd)) {
-		WARN_ON(1);
-		return NULL;
+		/* Clear the PMD if we hit a large mapping from the first round */
+		if (late_text) {
+			set_pmd(pmd, __pmd(0));
+		} else {
+			WARN_ON_ONCE(1);
+			return NULL;
+		}
 	}
 
 	if (pmd_none(*pmd)) {
@@ -283,7 +288,7 @@
 	if (!pte || WARN_ON(level != PG_LEVEL_4K) || pte_none(*pte))
 		return;
 
-	target_pte = pti_user_pagetable_walk_pte(VSYSCALL_ADDR);
+	target_pte = pti_user_pagetable_walk_pte(VSYSCALL_ADDR, false);
 	if (WARN_ON(!target_pte))
 		return;
 
@@ -301,7 +306,7 @@
 
 static void
 pti_clone_pgtable(unsigned long start, unsigned long end,
-		  enum pti_clone_level level)
+		  enum pti_clone_level level, bool late_text)
 {
 	unsigned long addr;
 
@@ -374,14 +379,14 @@
 			 */
 			*target_pmd = *pmd;
 
-			addr += PMD_SIZE;
+			addr = round_up(addr + 1, PMD_SIZE);
 
 		} else if (level == PTI_CLONE_PTE) {
 
 			/* Walk the page-table down to the pte level */
 			pte = pte_offset_kernel(pmd, addr);
 			if (pte_none(*pte)) {
-				addr += PAGE_SIZE;
+				addr = round_up(addr + 1, PAGE_SIZE);
 				continue;
 			}
 
@@ -390,7 +395,7 @@
 				return;
 
 			/* Allocate PTE in the user page-table */
-			target_pte = pti_user_pagetable_walk_pte(addr);
+			target_pte = pti_user_pagetable_walk_pte(addr, late_text);
 			if (WARN_ON(!target_pte))
 				return;
 
@@ -401,7 +406,7 @@
 			/* Clone the PTE */
 			*target_pte = *pte;
 
-			addr += PAGE_SIZE;
+			addr = round_up(addr + 1, PAGE_SIZE);
 
 		} else {
 			BUG();
@@ -452,7 +457,7 @@
 		phys_addr_t pa = per_cpu_ptr_to_phys((void *)va);
 		pte_t *target_pte;
 
-		target_pte = pti_user_pagetable_walk_pte(va);
+		target_pte = pti_user_pagetable_walk_pte(va, false);
 		if (WARN_ON(!target_pte))
 			return;
 
@@ -475,7 +480,7 @@
 	start = CPU_ENTRY_AREA_BASE;
 	end   = start + (PAGE_SIZE * CPU_ENTRY_AREA_PAGES);
 
-	pti_clone_pgtable(start, end, PTI_CLONE_PMD);
+	pti_clone_pgtable(start, end, PTI_CLONE_PMD, false);
 }
 #endif /* CONFIG_X86_64 */
 
@@ -492,11 +497,11 @@
 /*
  * Clone the populated PMDs of the entry text and force it RO.
  */
-static void pti_clone_entry_text(void)
+static void pti_clone_entry_text(bool late)
 {
 	pti_clone_pgtable((unsigned long) __entry_text_start,
 			  (unsigned long) __entry_text_end,
-			  PTI_CLONE_PMD);
+			  PTI_LEVEL_KERNEL_IMAGE, late);
 }
 
 /*
@@ -571,7 +576,7 @@
 	 * pti_set_kernel_image_nonglobal() did to clear the
 	 * global bit.
 	 */
-	pti_clone_pgtable(start, end_clone, PTI_LEVEL_KERNEL_IMAGE);
+	pti_clone_pgtable(start, end_clone, PTI_LEVEL_KERNEL_IMAGE, false);
 
 	/*
 	 * pti_clone_pgtable() will set the global bit in any PMDs
@@ -638,8 +643,15 @@
 
 	/* Undo all global bits from the init pagetables in head_64.S: */
 	pti_set_kernel_image_nonglobal();
+
 	/* Replace some of the global bits just for shared entry text: */
-	pti_clone_entry_text();
+	/*
+	 * This is very early in boot. Device and Late initcalls can do
+	 * modprobe before free_initmem() and mark_readonly(). This
+	 * pti_clone_entry_text() allows those user-mode-helpers to function,
+	 * but notably the text is still RW.
+	 */
+	pti_clone_entry_text(false);
 	pti_setup_espfix64();
 	pti_setup_vsyscall();
 }
@@ -656,10 +668,11 @@
 	if (!boot_cpu_has(X86_FEATURE_PTI))
 		return;
 	/*
-	 * We need to clone everything (again) that maps parts of the
-	 * kernel image.
+	 * This is after free_initmem() (all initcalls are done) and we've done
+	 * mark_readonly(). Text is now NX which might've split some PMDs
+	 * relative to the early clone.
 	 */
-	pti_clone_entry_text();
+	pti_clone_entry_text(true);
 	pti_clone_kernel_text();
 
 	debug_checkwx_user();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/mm/tlb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/mm/tlb.c
@@ -854,12 +854,37 @@
 			nr_invalidate);
 }
 
-static bool tlb_is_not_lazy(int cpu)
+static bool should_flush_tlb(int cpu, void *data)
 {
-	return !per_cpu(cpu_tlbstate_shared.is_lazy, cpu);
+	struct flush_tlb_info *info = data;
+
+	/* Lazy TLB will get flushed at the next context switch. */
+	if (per_cpu(cpu_tlbstate_shared.is_lazy, cpu))
+		return false;
+
+	/* No mm means kernel memory flush. */
+	if (!info->mm)
+		return true;
+
+	/* The target mm is loaded, and the CPU is not lazy. */
+	if (per_cpu(cpu_tlbstate.loaded_mm, cpu) == info->mm)
+		return true;
+
+	/* In cpumask, but not the loaded mm? Periodically remove by flushing. */
+	if (info->trim_cpumask)
+		return true;
+
+	return false;
 }
 
-static DEFINE_PER_CPU(cpumask_t, flush_tlb_mask);
+static bool should_trim_cpumask(struct mm_struct *mm)
+{
+	if (time_after(jiffies, READ_ONCE(mm->context.next_trim_cpumask))) {
+		WRITE_ONCE(mm->context.next_trim_cpumask, jiffies + HZ);
+		return true;
+	}
+	return false;
+}
 
 DEFINE_PER_CPU_SHARED_ALIGNED(struct tlb_state_shared, cpu_tlbstate_shared);
 EXPORT_PER_CPU_SYMBOL(cpu_tlbstate_shared);
@@ -889,36 +914,11 @@
 	 * up on the new contents of what used to be page tables, while
 	 * doing a speculative memory access.
 	 */
-	if (info->freed_tables) {
+	if (info->freed_tables)
 		on_each_cpu_mask(cpumask, flush_tlb_func, (void *)info, true);
-	} else {
-		/*
-		 * Although we could have used on_each_cpu_cond_mask(),
-		 * open-coding it has performance advantages, as it eliminates
-		 * the need for indirect calls or retpolines. In addition, it
-		 * allows to use a designated cpumask for evaluating the
-		 * condition, instead of allocating one.
-		 *
-		 * This code works under the assumption that there are no nested
-		 * TLB flushes, an assumption that is already made in
-		 * flush_tlb_mm_range().
-		 *
-		 * cond_cpumask is logically a stack-local variable, but it is
-		 * more efficient to have it off the stack and not to allocate
-		 * it on demand. Preemption is disabled and this code is
-		 * non-reentrant.
-		 */
-		struct cpumask *cond_cpumask = this_cpu_ptr(&flush_tlb_mask);
-		int cpu;
-
-		cpumask_clear(cond_cpumask);
-
-		for_each_cpu(cpu, cpumask) {
-			if (tlb_is_not_lazy(cpu))
-				__cpumask_set_cpu(cpu, cond_cpumask);
-		}
-		on_each_cpu_mask(cond_cpumask, flush_tlb_func, (void *)info, true);
-	}
+	else
+		on_each_cpu_cond_mask(should_flush_tlb, flush_tlb_func,
+				(void *)info, 1, cpumask);
 }
 
 void flush_tlb_multi(const struct cpumask *cpumask,
@@ -968,6 +968,7 @@
 	info->freed_tables	= freed_tables;
 	info->new_tlb_gen	= new_tlb_gen;
 	info->initiating_cpu	= smp_processor_id();
+	info->trim_cpumask	= 0;
 
 	return info;
 }
@@ -1010,6 +1011,7 @@
 	 * flush_tlb_func_local() directly in this case.
 	 */
 	if (cpumask_any_but(mm_cpumask(mm), cpu) < nr_cpu_ids) {
+		info->trim_cpumask = should_trim_cpumask(mm);
 		flush_tlb_multi(mm_cpumask(mm), info);
 	} else if (mm == this_cpu_read(cpu_tlbstate.loaded_mm)) {
 		lockdep_assert_irqs_enabled();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/net/bpf_jit_comp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/net/bpf_jit_comp.c
@@ -15,7 +15,6 @@
 #include <asm/set_memory.h>
 #include <asm/nospec-branch.h>
 #include <asm/text-patching.h>
-#include <asm/asm-prototypes.h>
 
 static u8 *emit_code(u8 *ptr, u32 bytes, unsigned int len)
 {
@@ -52,6 +51,56 @@
 	return value <= 127 && value >= -128;
 }
 
+/*
+ * Let us limit the positive offset to be <= 123.
+ * This is to ensure eventual jit convergence For the following patterns:
+ * ...
+ * pass4, final_proglen=4391:
+ *   ...
+ *   20e:    48 85 ff                test   rdi,rdi
+ *   211:    74 7d                   je     0x290
+ *   213:    48 8b 77 00             mov    rsi,QWORD PTR [rdi+0x0]
+ *   ...
+ *   289:    48 85 ff                test   rdi,rdi
+ *   28c:    74 17                   je     0x2a5
+ *   28e:    e9 7f ff ff ff          jmp    0x212
+ *   293:    bf 03 00 00 00          mov    edi,0x3
+ * Note that insn at 0x211 is 2-byte cond jump insn for offset 0x7d (-125)
+ * and insn at 0x28e is 5-byte jmp insn with offset -129.
+ *
+ * pass5, final_proglen=4392:
+ *   ...
+ *   20e:    48 85 ff                test   rdi,rdi
+ *   211:    0f 84 80 00 00 00       je     0x297
+ *   217:    48 8b 77 00             mov    rsi,QWORD PTR [rdi+0x0]
+ *   ...
+ *   28d:    48 85 ff                test   rdi,rdi
+ *   290:    74 1a                   je     0x2ac
+ *   292:    eb 84                   jmp    0x218
+ *   294:    bf 03 00 00 00          mov    edi,0x3
+ * Note that insn at 0x211 is 6-byte cond jump insn now since its offset
+ * becomes 0x80 based on previous round (0x293 - 0x213 = 0x80).
+ * At the same time, insn at 0x292 is a 2-byte insn since its offset is
+ * -124.
+ *
+ * pass6 will repeat the same code as in pass4 and this will prevent
+ * eventual convergence.
+ *
+ * To fix this issue, we need to break je (2->6 bytes) <-> jmp (5->2 bytes)
+ * cycle in the above. In the above example je offset <= 0x7c should work.
+ *
+ * For other cases, je <-> je needs offset <= 0x7b to avoid no convergence
+ * issue. For jmp <-> je and jmp <-> jmp cases, jmp offset <= 0x7c should
+ * avoid no convergence issue.
+ *
+ * Overall, let us limit the positive offset for 8bit cond/uncond jmp insn
+ * to maximum 123 (0x7b). This way, the jit pass can eventually converge.
+ */
+static bool is_imm8_jmp_offset(int value)
+{
+	return value <= 123 && value >= -128;
+}
+
 static bool is_simm32(s64 value)
 {
 	return value == (s64)(s32)value;
@@ -225,6 +274,14 @@
 
 struct jit_context {
 	int cleanup_addr; /* Epilogue code offset */
+
+	/*
+	 * Program specific offsets of labels in the code; these rely on the
+	 * JIT doing at least 2 passes, recording the position on the first
+	 * pass, only to generate the correct offset on the second pass.
+	 */
+	int tail_call_direct_label;
+	int tail_call_indirect_label;
 };
 
 /* Maximum number of bytes emitted while JITing one eBPF insn */
@@ -380,20 +437,38 @@
 	return __bpf_arch_text_poke(ip, t, old_addr, new_addr, true);
 }
 
-static int get_pop_bytes(bool *callee_regs_used)
+#define EMIT_LFENCE()	EMIT3(0x0F, 0xAE, 0xE8)
+
+static void emit_indirect_jump(u8 **pprog, int reg, u8 *ip)
 {
-	int bytes = 0;
+	u8 *prog = *pprog;
 
-	if (callee_regs_used[3])
-		bytes += 2;
-	if (callee_regs_used[2])
-		bytes += 2;
-	if (callee_regs_used[1])
-		bytes += 2;
-	if (callee_regs_used[0])
-		bytes += 1;
+#ifdef CONFIG_RETPOLINE
+	if (cpu_feature_enabled(X86_FEATURE_RETPOLINE_LFENCE)) {
+		EMIT_LFENCE();
+		EMIT2(0xFF, 0xE0 + reg);
+	} else if (cpu_feature_enabled(X86_FEATURE_RETPOLINE)) {
+		emit_jump(&prog, &__x86_indirect_thunk_array[reg], ip);
+	} else
+#endif
+	EMIT2(0xFF, 0xE0 + reg);
 
-	return bytes;
+	*pprog = prog;
+}
+
+static void emit_return(u8 **pprog, u8 *ip)
+{
+	u8 *prog = *pprog;
+
+	if (cpu_feature_enabled(X86_FEATURE_RETHUNK)) {
+		emit_jump(&prog, x86_return_thunk, ip);
+	} else {
+		EMIT1(0xC3);		/* ret */
+		if (IS_ENABLED(CONFIG_SLS))
+			EMIT1(0xCC);	/* int3 */
+	}
+
+	*pprog = prog;
 }
 
 /*
@@ -411,29 +486,12 @@
  * out:
  */
 static void emit_bpf_tail_call_indirect(u8 **pprog, bool *callee_regs_used,
-					u32 stack_depth)
+					u32 stack_depth, u8 *ip,
+					struct jit_context *ctx)
 {
 	int tcc_off = -4 - round_up(stack_depth, 8);
-	u8 *prog = *pprog;
-	int pop_bytes = 0;
-	int off1 = 42;
-	int off2 = 31;
-	int off3 = 9;
-
-	/* count the additional bytes used for popping callee regs from stack
-	 * that need to be taken into account for each of the offsets that
-	 * are used for bailing out of the tail call
-	 */
-	pop_bytes = get_pop_bytes(callee_regs_used);
-	off1 += pop_bytes;
-	off2 += pop_bytes;
-	off3 += pop_bytes;
-
-	if (stack_depth) {
-		off1 += 7;
-		off2 += 7;
-		off3 += 7;
-	}
+	u8 *prog = *pprog, *start = *pprog;
+	int offset;
 
 	/*
 	 * rdi - pointer to ctx
@@ -448,8 +506,9 @@
 	EMIT2(0x89, 0xD2);                        /* mov edx, edx */
 	EMIT3(0x39, 0x56,                         /* cmp dword ptr [rsi + 16], edx */
 	      offsetof(struct bpf_array, map.max_entries));
-#define OFFSET1 (off1 + RETPOLINE_RCX_BPF_JIT_SIZE) /* Number of bytes to jump */
-	EMIT2(X86_JBE, OFFSET1);                  /* jbe out */
+
+	offset = ctx->tail_call_indirect_label - (prog + 2 - start);
+	EMIT2(X86_JBE, offset);                   /* jbe out */
 
 	/*
 	 * if (tail_call_cnt > MAX_TAIL_CALL_CNT)
@@ -457,8 +516,9 @@
 	 */
 	EMIT2_off32(0x8B, 0x85, tcc_off);         /* mov eax, dword ptr [rbp - tcc_off] */
 	EMIT3(0x83, 0xF8, MAX_TAIL_CALL_CNT);     /* cmp eax, MAX_TAIL_CALL_CNT */
-#define OFFSET2 (off2 + RETPOLINE_RCX_BPF_JIT_SIZE)
-	EMIT2(X86_JA, OFFSET2);                   /* ja out */
+
+	offset = ctx->tail_call_indirect_label - (prog + 2 - start);
+	EMIT2(X86_JA, offset);                    /* ja out */
 	EMIT3(0x83, 0xC0, 0x01);                  /* add eax, 1 */
 	EMIT2_off32(0x89, 0x85, tcc_off);         /* mov dword ptr [rbp - tcc_off], eax */
 
@@ -471,12 +531,11 @@
 	 *	goto out;
 	 */
 	EMIT3(0x48, 0x85, 0xC9);                  /* test rcx,rcx */
-#define OFFSET3 (off3 + RETPOLINE_RCX_BPF_JIT_SIZE)
-	EMIT2(X86_JE, OFFSET3);                   /* je out */
 
-	*pprog = prog;
-	pop_callee_regs(pprog, callee_regs_used);
-	prog = *pprog;
+	offset = ctx->tail_call_indirect_label - (prog + 2 - start);
+	EMIT2(X86_JE, offset);                    /* je out */
+
+	pop_callee_regs(&prog, callee_regs_used);
 
 	EMIT1(0x58);                              /* pop rax */
 	if (stack_depth)
@@ -493,41 +552,21 @@
 	 * rdi == ctx (1st arg)
 	 * rcx == prog->bpf_func + X86_TAIL_CALL_OFFSET
 	 */
-	RETPOLINE_RCX_BPF_JIT();
+	emit_indirect_jump(&prog, 1 /* rcx */, ip + (prog - start));
 
 	/* out: */
+	ctx->tail_call_indirect_label = prog - start;
 	*pprog = prog;
 }
 
 static void emit_bpf_tail_call_direct(struct bpf_jit_poke_descriptor *poke,
-				      u8 **pprog, int addr, u8 *image,
-				      bool *callee_regs_used, u32 stack_depth)
+				      u8 **pprog, u8 *ip,
+				      bool *callee_regs_used, u32 stack_depth,
+				      struct jit_context *ctx)
 {
 	int tcc_off = -4 - round_up(stack_depth, 8);
-	u8 *prog = *pprog;
-	int pop_bytes = 0;
-	int off1 = 20;
-	int poke_off;
-
-	/* count the additional bytes used for popping callee regs to stack
-	 * that need to be taken into account for jump offset that is used for
-	 * bailing out from of the tail call when limit is reached
-	 */
-	pop_bytes = get_pop_bytes(callee_regs_used);
-	off1 += pop_bytes;
-
-	/*
-	 * total bytes for:
-	 * - nop5/ jmpq $off
-	 * - pop callee regs
-	 * - sub rsp, $val if depth > 0
-	 * - pop rax
-	 */
-	poke_off = X86_PATCH_SIZE + pop_bytes + 1;
-	if (stack_depth) {
-		poke_off += 7;
-		off1 += 7;
-	}
+	u8 *prog = *pprog, *start = *pprog;
+	int offset;
 
 	/*
 	 * if (tail_call_cnt > MAX_TAIL_CALL_CNT)
@@ -535,28 +574,30 @@
 	 */
 	EMIT2_off32(0x8B, 0x85, tcc_off);             /* mov eax, dword ptr [rbp - tcc_off] */
 	EMIT3(0x83, 0xF8, MAX_TAIL_CALL_CNT);         /* cmp eax, MAX_TAIL_CALL_CNT */
-	EMIT2(X86_JA, off1);                          /* ja out */
+
+	offset = ctx->tail_call_direct_label - (prog + 2 - start);
+	EMIT2(X86_JA, offset);                        /* ja out */
 	EMIT3(0x83, 0xC0, 0x01);                      /* add eax, 1 */
 	EMIT2_off32(0x89, 0x85, tcc_off);             /* mov dword ptr [rbp - tcc_off], eax */
 
-	poke->tailcall_bypass = image + (addr - poke_off - X86_PATCH_SIZE);
+	poke->tailcall_bypass = ip + (prog - start);
 	poke->adj_off = X86_TAIL_CALL_OFFSET;
-	poke->tailcall_target = image + (addr - X86_PATCH_SIZE);
+	poke->tailcall_target = ip + ctx->tail_call_direct_label - X86_PATCH_SIZE;
 	poke->bypass_addr = (u8 *)poke->tailcall_target + X86_PATCH_SIZE;
 
 	emit_jump(&prog, (u8 *)poke->tailcall_target + X86_PATCH_SIZE,
 		  poke->tailcall_bypass);
 
-	*pprog = prog;
-	pop_callee_regs(pprog, callee_regs_used);
-	prog = *pprog;
+	pop_callee_regs(&prog, callee_regs_used);
 	EMIT1(0x58);                                  /* pop rax */
 	if (stack_depth)
 		EMIT3_off32(0x48, 0x81, 0xC4, round_up(stack_depth, 8));
 
 	memcpy(prog, x86_nops[5], X86_PATCH_SIZE);
 	prog += X86_PATCH_SIZE;
+
 	/* out: */
+	ctx->tail_call_direct_label = prog - start;
 
 	*pprog = prog;
 }
@@ -721,6 +762,20 @@
 	*pprog = prog;
 }
 
+/*
+ * Similar version of maybe_emit_mod() for a single register
+ */
+static void maybe_emit_1mod(u8 **pprog, u32 reg, bool is64)
+{
+	u8 *prog = *pprog;
+
+	if (is64)
+		EMIT1(add_1mod(0x48, reg));
+	else if (is_ereg(reg))
+		EMIT1(add_1mod(0x40, reg));
+	*pprog = prog;
+}
+
 /* LDX: dst_reg = *(u8*)(src_reg + off) */
 static void emit_ldx(u8 **pprog, u32 size, u32 dst_reg, u32 src_reg, int off)
 {
@@ -827,9 +882,7 @@
 	return 0;
 }
 
-static bool ex_handler_bpf(const struct exception_table_entry *x,
-			   struct pt_regs *regs, int trapnr,
-			   unsigned long error_code, unsigned long fault_addr)
+bool ex_handler_bpf(const struct exception_table_entry *x, struct pt_regs *regs)
 {
 	u32 reg = x->fixup >> 8;
 
@@ -951,10 +1004,8 @@
 			/* neg dst */
 		case BPF_ALU | BPF_NEG:
 		case BPF_ALU64 | BPF_NEG:
-			if (BPF_CLASS(insn->code) == BPF_ALU64)
-				EMIT1(add_1mod(0x48, dst_reg));
-			else if (is_ereg(dst_reg))
-				EMIT1(add_1mod(0x40, dst_reg));
+			maybe_emit_1mod(&prog, dst_reg,
+					BPF_CLASS(insn->code) == BPF_ALU64);
 			EMIT2(0xF7, add_1reg(0xD8, dst_reg));
 			break;
 
@@ -968,10 +1019,8 @@
 		case BPF_ALU64 | BPF_AND | BPF_K:
 		case BPF_ALU64 | BPF_OR | BPF_K:
 		case BPF_ALU64 | BPF_XOR | BPF_K:
-			if (BPF_CLASS(insn->code) == BPF_ALU64)
-				EMIT1(add_1mod(0x48, dst_reg));
-			else if (is_ereg(dst_reg))
-				EMIT1(add_1mod(0x40, dst_reg));
+			maybe_emit_1mod(&prog, dst_reg,
+					BPF_CLASS(insn->code) == BPF_ALU64);
 
 			/*
 			 * b3 holds 'normal' opcode, b2 short form only valid
@@ -1112,10 +1161,8 @@
 		case BPF_ALU64 | BPF_LSH | BPF_K:
 		case BPF_ALU64 | BPF_RSH | BPF_K:
 		case BPF_ALU64 | BPF_ARSH | BPF_K:
-			if (BPF_CLASS(insn->code) == BPF_ALU64)
-				EMIT1(add_1mod(0x48, dst_reg));
-			else if (is_ereg(dst_reg))
-				EMIT1(add_1mod(0x40, dst_reg));
+			maybe_emit_1mod(&prog, dst_reg,
+					BPF_CLASS(insn->code) == BPF_ALU64);
 
 			b3 = simple_alu_opcodes[BPF_OP(insn->code)];
 			if (imm32 == 1)
@@ -1146,10 +1193,8 @@
 			}
 
 			/* shl %rax, %cl | shr %rax, %cl | sar %rax, %cl */
-			if (BPF_CLASS(insn->code) == BPF_ALU64)
-				EMIT1(add_1mod(0x48, dst_reg));
-			else if (is_ereg(dst_reg))
-				EMIT1(add_1mod(0x40, dst_reg));
+			maybe_emit_1mod(&prog, dst_reg,
+					BPF_CLASS(insn->code) == BPF_ALU64);
 
 			b3 = simple_alu_opcodes[BPF_OP(insn->code)];
 			EMIT2(0xD3, add_1reg(b3, dst_reg));
@@ -1222,8 +1267,7 @@
 			/* speculation barrier */
 		case BPF_ST | BPF_NOSPEC:
 			if (boot_cpu_has(X86_FEATURE_XMM2))
-				/* Emit 'lfence' */
-				EMIT3(0x0F, 0xAE, 0xE8);
+				EMIT_LFENCE();
 			break;
 
 			/* ST: *(u8*)(dst_reg + off) = imm */
@@ -1274,19 +1318,54 @@
 		case BPF_LDX | BPF_MEM | BPF_DW:
 		case BPF_LDX | BPF_PROBE_MEM | BPF_DW:
 			if (BPF_MODE(insn->code) == BPF_PROBE_MEM) {
-				/* test src_reg, src_reg */
-				maybe_emit_mod(&prog, src_reg, src_reg, true); /* always 1 byte */
-				EMIT2(0x85, add_2reg(0xC0, src_reg, src_reg));
-				/* jne start_of_ldx */
-				EMIT2(X86_JNE, 0);
+				/* Though the verifier prevents negative insn->off in BPF_PROBE_MEM
+				 * add abs(insn->off) to the limit to make sure that negative
+				 * offset won't be an issue.
+				 * insn->off is s16, so it won't affect valid pointers.
+				 */
+				u64 limit = TASK_SIZE_MAX + PAGE_SIZE + abs(insn->off);
+				u8 *end_of_jmp1, *end_of_jmp2;
+
+				/* Conservatively check that src_reg + insn->off is a kernel address:
+				 * 1. src_reg + insn->off >= limit
+				 * 2. src_reg + insn->off doesn't become small positive.
+				 * Cannot do src_reg + insn->off >= limit in one branch,
+				 * since it needs two spare registers, but JIT has only one.
+				 */
+
+				/* movabsq r11, limit */
+				EMIT2(add_1mod(0x48, AUX_REG), add_1reg(0xB8, AUX_REG));
+				EMIT((u32)limit, 4);
+				EMIT(limit >> 32, 4);
+				/* cmp src_reg, r11 */
+				maybe_emit_mod(&prog, src_reg, AUX_REG, true);
+				EMIT2(0x39, add_2reg(0xC0, src_reg, AUX_REG));
+				/* if unsigned '<' goto end_of_jmp2 */
+				EMIT2(X86_JB, 0);
+				end_of_jmp1 = prog;
+
+				/* mov r11, src_reg */
+				emit_mov_reg(&prog, true, AUX_REG, src_reg);
+				/* add r11, insn->off */
+				maybe_emit_1mod(&prog, AUX_REG, true);
+				EMIT2_off32(0x81, add_1reg(0xC0, AUX_REG), insn->off);
+				/* jmp if not carry to start_of_ldx
+				 * Otherwise ERR_PTR(-EINVAL) + 128 will be the user addr
+				 * that has to be rejected.
+				 */
+				EMIT2(0x73 /* JNC */, 0);
+				end_of_jmp2 = prog;
+
 				/* xor dst_reg, dst_reg */
 				emit_mov_imm32(&prog, false, dst_reg, 0);
 				/* jmp byte_after_ldx */
 				EMIT2(0xEB, 0);
 
-				/* populate jmp_offset for JNE above */
-				temp[4] = prog - temp - 5 /* sizeof(test + jne) */;
+				/* populate jmp_offset for JB above to jump to xor dst_reg */
+				end_of_jmp1[-1] = end_of_jmp2 - end_of_jmp1;
+				/* populate jmp_offset for JNC above to jump to start_of_ldx */
 				start_of_ldx = prog;
+				end_of_jmp2[-1] = start_of_ldx - end_of_jmp2;
 			}
 			emit_ldx(&prog, BPF_SIZE(insn->code), dst_reg, src_reg, insn->off);
 			if (BPF_MODE(insn->code) == BPF_PROBE_MEM) {
@@ -1313,12 +1392,7 @@
 				}
 				ex->insn = delta;
 
-				delta = (u8 *)ex_handler_bpf - (u8 *)&ex->handler;
-				if (!is_simm32(delta)) {
-					pr_err("extable->handler doesn't fit into 32-bit\n");
-					return -EFAULT;
-				}
-				ex->handler = delta;
+				ex->data = EX_TYPE_BPF;
 
 				if (dst_reg > BPF_REG_9) {
 					pr_err("verifier error\n");
@@ -1332,7 +1406,7 @@
 				 * End result: x86 insn "mov rbx, qword ptr [rax+0x14]"
 				 * of 4 bytes will be ignored and rbx will be zero inited.
 				 */
-				ex->fixup = (prog - temp) | (reg2pt_regs[dst_reg] << 8);
+				ex->fixup = (prog - start_of_ldx) | (reg2pt_regs[dst_reg] << 8);
 			}
 			break;
 
@@ -1399,8 +1473,9 @@
 		case BPF_JMP | BPF_CALL:
 			func = (u8 *) __bpf_call_base + imm32;
 			if (tail_call_reachable) {
+				/* mov rax, qword ptr [rbp - rounded_stack_depth - 8] */
 				EMIT3_off32(0x48, 0x8B, 0x85,
-					    -(bpf_prog->aux->stack_depth + 8));
+					    -round_up(bpf_prog->aux->stack_depth, 8) - 8);
 				if (!imm32 || emit_call(&prog, func, image + addrs[i - 1] + 7))
 					return -EINVAL;
 			} else {
@@ -1412,13 +1487,16 @@
 		case BPF_JMP | BPF_TAIL_CALL:
 			if (imm32)
 				emit_bpf_tail_call_direct(&bpf_prog->aux->poke_tab[imm32 - 1],
-							  &prog, addrs[i], image,
+							  &prog, image + addrs[i - 1],
 							  callee_regs_used,
-							  bpf_prog->aux->stack_depth);
+							  bpf_prog->aux->stack_depth,
+							  ctx);
 			else
 				emit_bpf_tail_call_indirect(&prog,
 							    callee_regs_used,
-							    bpf_prog->aux->stack_depth);
+							    bpf_prog->aux->stack_depth,
+							    image + addrs[i - 1],
+							    ctx);
 			break;
 
 			/* cond jump */
@@ -1459,10 +1537,8 @@
 		case BPF_JMP | BPF_JSET | BPF_K:
 		case BPF_JMP32 | BPF_JSET | BPF_K:
 			/* test dst_reg, imm32 */
-			if (BPF_CLASS(insn->code) == BPF_JMP)
-				EMIT1(add_1mod(0x48, dst_reg));
-			else if (is_ereg(dst_reg))
-				EMIT1(add_1mod(0x40, dst_reg));
+			maybe_emit_1mod(&prog, dst_reg,
+					BPF_CLASS(insn->code) == BPF_JMP);
 			EMIT2_off32(0xF7, add_1reg(0xC0, dst_reg), imm32);
 			goto emit_cond_jmp;
 
@@ -1495,10 +1571,8 @@
 			}
 
 			/* cmp dst_reg, imm8/32 */
-			if (BPF_CLASS(insn->code) == BPF_JMP)
-				EMIT1(add_1mod(0x48, dst_reg));
-			else if (is_ereg(dst_reg))
-				EMIT1(add_1mod(0x40, dst_reg));
+			maybe_emit_1mod(&prog, dst_reg,
+					BPF_CLASS(insn->code) == BPF_JMP);
 
 			if (is_imm8(imm32))
 				EMIT3(0x83, add_1reg(0xF8, dst_reg), imm32);
@@ -1550,7 +1624,7 @@
 				return -EFAULT;
 			}
 			jmp_offset = addrs[i + insn->off] - addrs[i];
-			if (is_imm8(jmp_offset)) {
+			if (is_imm8_jmp_offset(jmp_offset)) {
 				if (jmp_padding) {
 					/* To keep the jmp_offset valid, the extra bytes are
 					 * padded before the jump insn, so we subtract the
@@ -1624,7 +1698,7 @@
 				break;
 			}
 emit_jmp:
-			if (is_imm8(jmp_offset)) {
+			if (is_imm8_jmp_offset(jmp_offset)) {
 				if (jmp_padding) {
 					/* To avoid breaking jmp_offset, the extra bytes
 					 * are padded before the actual jmp insn, so
@@ -1665,7 +1739,7 @@
 			ctx->cleanup_addr = proglen;
 			pop_callee_regs(&prog, callee_regs_used);
 			EMIT1(0xC9);         /* leave */
-			EMIT1(0xC3);         /* ret */
+			emit_return(&prog, image + addrs[i - 1] + (prog - temp));
 			break;
 
 		default:
@@ -2111,7 +2185,7 @@
 	if (flags & BPF_TRAMP_F_SKIP_FRAME)
 		/* skip our return address and return to parent */
 		EMIT4(0x48, 0x83, 0xC4, 8); /* add rsp, 8 */
-	EMIT1(0xC3); /* ret */
+	emit_return(&prog, prog);
 	/* Make sure the trampoline generation logic doesn't overflow */
 	if (WARN_ON_ONCE(prog > (u8 *)image_end - BPF_INSN_SAFETY)) {
 		ret = -EFAULT;
@@ -2124,24 +2198,6 @@
 	return ret;
 }
 
-static int emit_fallback_jump(u8 **pprog)
-{
-	u8 *prog = *pprog;
-	int err = 0;
-
-#ifdef CONFIG_RETPOLINE
-	/* Note that this assumes the the compiler uses external
-	 * thunks for indirect calls. Both clang and GCC use the same
-	 * naming convention for external thunks.
-	 */
-	err = emit_jump(&prog, __x86_indirect_thunk_rdx, prog);
-#else
-	EMIT2(0xFF, 0xE2);	/* jmp rdx */
-#endif
-	*pprog = prog;
-	return err;
-}
-
 static int emit_bpf_dispatcher(u8 **pprog, int a, int b, s64 *progs)
 {
 	u8 *jg_reloc, *prog = *pprog;
@@ -2163,9 +2219,7 @@
 		if (err)
 			return err;
 
-		err = emit_fallback_jump(&prog);	/* jmp thunk/indirect */
-		if (err)
-			return err;
+		emit_indirect_jump(&prog, 2 /* rdx */, prog);
 
 		*pprog = prog;
 		return 0;
@@ -2399,3 +2453,49 @@
 {
 	return true;
 }
+
+void bpf_arch_poke_desc_update(struct bpf_jit_poke_descriptor *poke,
+			       struct bpf_prog *new, struct bpf_prog *old)
+{
+	u8 *old_addr, *new_addr, *old_bypass_addr;
+	int ret;
+
+	old_bypass_addr = old ? NULL : poke->bypass_addr;
+	old_addr = old ? (u8 *)old->bpf_func + poke->adj_off : NULL;
+	new_addr = new ? (u8 *)new->bpf_func + poke->adj_off : NULL;
+
+	/*
+	 * On program loading or teardown, the program's kallsym entry
+	 * might not be in place, so we use __bpf_arch_text_poke to skip
+	 * the kallsyms check.
+	 */
+	if (new) {
+		ret = __bpf_arch_text_poke(poke->tailcall_target,
+					   BPF_MOD_JUMP,
+					   old_addr, new_addr, true);
+		BUG_ON(ret < 0);
+		if (!old) {
+			ret = __bpf_arch_text_poke(poke->tailcall_bypass,
+						   BPF_MOD_JUMP,
+						   poke->bypass_addr,
+						   NULL, true);
+			BUG_ON(ret < 0);
+		}
+	} else {
+		ret = __bpf_arch_text_poke(poke->tailcall_bypass,
+					   BPF_MOD_JUMP,
+					   old_bypass_addr,
+					   poke->bypass_addr, true);
+		BUG_ON(ret < 0);
+		/* let other CPUs finish the execution of program
+		 * so that it will not possible to expose them
+		 * to invalid nop, stack unwind, nop state
+		 */
+		if (!ret)
+			synchronize_rcu();
+		ret = __bpf_arch_text_poke(poke->tailcall_target,
+					   BPF_MOD_JUMP,
+					   old_addr, NULL, true);
+		BUG_ON(ret < 0);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/net/bpf_jit_comp32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/net/bpf_jit_comp32.c
@@ -15,6 +15,7 @@
 #include <asm/cacheflush.h>
 #include <asm/set_memory.h>
 #include <asm/nospec-branch.h>
+#include <asm/asm-prototypes.h>
 #include <linux/bpf.h>
 
 /*
@@ -1267,6 +1268,21 @@
 	*pprog = prog;
 }
 
+static int emit_jmp_edx(u8 **pprog, u8 *ip)
+{
+	u8 *prog = *pprog;
+	int cnt = 0;
+
+#ifdef CONFIG_RETPOLINE
+	EMIT1_off32(0xE9, (u8 *)__x86_indirect_thunk_edx - (ip + 5));
+#else
+	EMIT2(0xFF, 0xE2);
+#endif
+	*pprog = prog;
+
+	return cnt;
+}
+
 /*
  * Generate the following code:
  * ... bpf_tail_call(void *ctx, struct bpf_array *array, u64 index) ...
@@ -1280,7 +1296,7 @@
  *   goto *(prog->bpf_func + prologue_size);
  * out:
  */
-static void emit_bpf_tail_call(u8 **pprog)
+static void emit_bpf_tail_call(u8 **pprog, u8 *ip)
 {
 	u8 *prog = *pprog;
 	int cnt = 0;
@@ -1362,7 +1378,7 @@
 	 * eax == ctx (1st arg)
 	 * edx == prog->bpf_func + prologue_size
 	 */
-	RETPOLINE_EDX_BPF_JIT();
+	cnt += emit_jmp_edx(&prog, ip + cnt);
 
 	if (jmp_label1 == -1)
 		jmp_label1 = cnt;
@@ -2122,7 +2138,7 @@
 			break;
 		}
 		case BPF_JMP | BPF_TAIL_CALL:
-			emit_bpf_tail_call(&prog);
+			emit_bpf_tail_call(&prog, image + addrs[i - 1]);
 			break;
 
 		/* cond jump */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/acpi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/acpi.c
@@ -19,6 +19,7 @@
 #endif
 };
 
+bool pci_use_e820 = true;
 static bool pci_use_crs = true;
 static bool pci_ignore_seg = false;
 
@@ -41,6 +42,14 @@
 	return 0;
 }
 
+static int __init set_no_e820(const struct dmi_system_id *id)
+{
+	printk(KERN_INFO "PCI: %s detected: not clipping E820 regions from _CRS\n",
+	       id->ident);
+	pci_use_e820 = false;
+	return 0;
+}
+
 static const struct dmi_system_id pci_crs_quirks[] __initconst = {
 	/* http://bugzilla.kernel.org/show_bug.cgi?id=14183 */
 	{
@@ -135,6 +144,51 @@
 			DMI_MATCH(DMI_PRODUCT_NAME, "HP xw9300 Workstation"),
 		},
 	},
+
+	/*
+	 * Many Lenovo models with "IIL" in their DMI_PRODUCT_VERSION have
+	 * an E820 reserved region that covers the entire 32-bit host
+	 * bridge memory window from _CRS.  Using the E820 region to clip
+	 * _CRS means no space is available for hot-added or uninitialized
+	 * PCI devices.  This typically breaks I2C controllers for touchpads
+	 * and hot-added Thunderbolt devices.  See the commit log for
+	 * models known to require this quirk and related bug reports.
+	 */
+	{
+		.callback = set_no_e820,
+		.ident = "Lenovo *IIL* product version",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "IIL"),
+		},
+	},
+
+	/*
+	 * The Acer Spin 5 (SP513-54N) has the same E820 reservation covering
+	 * the entire _CRS 32-bit window issue as the Lenovo *IIL* models.
+	 * See https://bugs.launchpad.net/bugs/1884232
+	 */
+	{
+		.callback = set_no_e820,
+		.ident = "Acer Spin 5 (SP513-54N)",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Spin SP513-54N"),
+		},
+	},
+
+	/*
+	 * Clevo X170KM-G barebones have the same E820 reservation covering
+	 * the entire _CRS 32-bit window issue as the Lenovo *IIL* models.
+	 * See https://bugzilla.kernel.org/show_bug.cgi?id=214259
+	 */
+	{
+		.callback = set_no_e820,
+		.ident = "Clevo X170KM-G Barebone",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "X170KM-G"),
+		},
+	},
 	{}
 };
 
@@ -160,6 +214,136 @@
 	       "if necessary, use \"pci=%s\" and report a bug\n",
 	       pci_use_crs ? "Using" : "Ignoring",
 	       pci_use_crs ? "nocrs" : "use_crs");
+
+	/* "pci=use_e820"/"pci=no_e820" on the kernel cmdline takes precedence */
+	if (pci_probe & PCI_NO_E820)
+		pci_use_e820 = false;
+	else if (pci_probe & PCI_USE_E820)
+		pci_use_e820 = true;
+
+	printk(KERN_INFO "PCI: %s E820 reservations for host bridge windows\n",
+	       pci_use_e820 ? "Using" : "Ignoring");
+	if (pci_probe & (PCI_NO_E820 | PCI_USE_E820))
+		printk(KERN_INFO "PCI: Please notify linux-pci@vger.kernel.org so future kernels can this automatically\n");
+}
+
+/*
+ * Check if pdev is part of a PCIe switch that is directly below the
+ * specified bridge.
+ */
+static bool pcie_switch_directly_under(struct pci_dev *bridge,
+				       struct pci_dev *pdev)
+{
+	struct pci_dev *parent = pci_upstream_bridge(pdev);
+
+	/* If the device doesn't have a parent, it's not under anything */
+	if (!parent)
+		return false;
+
+	/*
+	 * If the device has a PCIe type, check if it is below the
+	 * corresponding PCIe switch components (if applicable). Then check
+	 * if its upstream port is directly beneath the specified bridge.
+	 */
+	switch (pci_pcie_type(pdev)) {
+	case PCI_EXP_TYPE_UPSTREAM:
+		return parent == bridge;
+
+	case PCI_EXP_TYPE_DOWNSTREAM:
+		if (pci_pcie_type(parent) != PCI_EXP_TYPE_UPSTREAM)
+			return false;
+		parent = pci_upstream_bridge(parent);
+		return parent == bridge;
+
+	case PCI_EXP_TYPE_ENDPOINT:
+		if (pci_pcie_type(parent) != PCI_EXP_TYPE_DOWNSTREAM)
+			return false;
+		parent = pci_upstream_bridge(parent);
+		if (!parent || pci_pcie_type(parent) != PCI_EXP_TYPE_UPSTREAM)
+			return false;
+		parent = pci_upstream_bridge(parent);
+		return parent == bridge;
+	}
+
+	return false;
+}
+
+static bool pcie_has_usb4_host_interface(struct pci_dev *pdev)
+{
+	struct fwnode_handle *fwnode;
+
+	/*
+	 * For USB4, the tunneled PCIe Root or Downstream Ports are marked
+	 * with the "usb4-host-interface" ACPI property, so we look for
+	 * that first. This should cover most cases.
+	 */
+	fwnode = fwnode_find_reference(dev_fwnode(&pdev->dev),
+				       "usb4-host-interface", 0);
+	if (!IS_ERR(fwnode)) {
+		fwnode_handle_put(fwnode);
+		return true;
+	}
+
+	/*
+	 * Any integrated Thunderbolt 3/4 PCIe Root Ports from Intel
+	 * before Alder Lake do not have the "usb4-host-interface"
+	 * property so we use their PCI IDs instead. All these are
+	 * tunneled. This list is not expected to grow.
+	 */
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+		switch (pdev->device) {
+		/* Ice Lake Thunderbolt 3 PCIe Root Ports */
+		case 0x8a1d:
+		case 0x8a1f:
+		case 0x8a21:
+		case 0x8a23:
+		/* Tiger Lake-LP Thunderbolt 4 PCIe Root Ports */
+		case 0x9a23:
+		case 0x9a25:
+		case 0x9a27:
+		case 0x9a29:
+		/* Tiger Lake-H Thunderbolt 4 PCIe Root Ports */
+		case 0x9a2b:
+		case 0x9a2d:
+		case 0x9a2f:
+		case 0x9a31:
+			return true;
+		}
+	}
+
+	return false;
+}
+
+bool arch_pci_dev_is_removable(struct pci_dev *pdev)
+{
+	struct pci_dev *parent, *root;
+
+	/* pdev without a parent or Root Port is never tunneled */
+	parent = pci_upstream_bridge(pdev);
+	if (!parent)
+		return false;
+	root = pcie_find_root_port(pdev);
+	if (!root)
+		return false;
+
+	/* Internal PCIe devices are not tunneled */
+	if (!root->external_facing)
+		return false;
+
+	/* Anything directly behind a "usb4-host-interface" is tunneled */
+	if (pcie_has_usb4_host_interface(parent))
+		return true;
+
+	/*
+	 * Check if this is a discrete Thunderbolt/USB4 controller that is
+	 * directly behind the non-USB4 PCIe Root Port marked as
+	 * "ExternalFacingPort". Those are not behind a PCIe tunnel.
+	 */
+	if (pcie_switch_directly_under(root, pdev))
+		return false;
+
+	/* PCIe devices after the discrete chip are tunneled */
+	return true;
 }
 
 #ifdef	CONFIG_PCI_MMCONFIG
@@ -299,6 +483,7 @@
 	int status;
 
 	status = acpi_pci_probe_root_resources(ci);
+
 	if (pci_use_crs) {
 		resource_list_for_each_entry_safe(entry, tmp, &ci->resources)
 			if (resource_is_pcicfg_ioport(entry->res))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/common.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/common.c
@@ -34,6 +34,7 @@
 #endif
 int pcibios_last_bus = -1;
 unsigned long pirq_table_addr;
+unsigned int pci_early_clear_msi;
 const struct pci_raw_ops *__read_mostly raw_pci_ops;
 const struct pci_raw_ops *__read_mostly raw_pci_ext_ops;
 
@@ -595,6 +596,14 @@
 	} else if (!strcmp(str, "nocrs")) {
 		pci_probe |= PCI_ROOT_NO_CRS;
 		return NULL;
+	} else if (!strcmp(str, "use_e820")) {
+		pci_probe |= PCI_USE_E820;
+		add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK);
+		return NULL;
+	} else if (!strcmp(str, "no_e820")) {
+		pci_probe |= PCI_NO_E820;
+		add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK);
+		return NULL;
 #ifdef CONFIG_PHYS_ADDR_T_64BIT
 	} else if (!strcmp(str, "big_root_window")) {
 		pci_probe |= PCI_BIG_ROOT_WINDOW;
@@ -606,6 +615,9 @@
 	} else if (!strcmp(str, "skip_isa_align")) {
 		pci_probe |= PCI_CAN_SKIP_ISA_ALIGN;
 		return NULL;
+	} else if (!strcmp(str, "clearmsi")) {
+		pci_early_clear_msi = 1;
+		return NULL;
 	} else if (!strcmp(str, "noioapicquirk")) {
 		noioapicquirk = 1;
 		return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/early.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/early.c
@@ -51,6 +51,31 @@
 	outw(val, 0xcfc + (offset&2));
 }
 
+u32 pci_early_find_cap(int bus, int slot, int func, int cap)
+{
+	int bytes;
+	u8 pos;
+
+	if (!(read_pci_config_16(bus, slot, func, PCI_STATUS) &
+						PCI_STATUS_CAP_LIST))
+		return 0;
+
+	pos = read_pci_config_byte(bus, slot, func, PCI_CAPABILITY_LIST);
+	for (bytes = 0; bytes < 48 && pos >= 0x40; bytes++) {
+		u8 id;
+
+		pos &= ~3;
+		id = read_pci_config_byte(bus, slot, func, pos+PCI_CAP_LIST_ID);
+		if (id == 0xff)
+			break;
+		if (id == cap)
+			return pos;
+		pos = read_pci_config_byte(bus, slot, func,
+						pos+PCI_CAP_LIST_NEXT);
+	}
+	return 0;
+}
+
 int early_pci_allowed(void)
 {
 	return (pci_probe & (PCI_PROBE_CONF1|PCI_PROBE_NOEARLY)) ==
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/fixup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/fixup.c
@@ -7,6 +7,7 @@
 #include <linux/dmi.h>
 #include <linux/pci.h>
 #include <linux/vgaarb.h>
+#include <asm/amd_nb.h>
 #include <asm/hpet.h>
 #include <asm/pci_x86.h>
 
@@ -353,8 +354,8 @@
 		}
 	}
 }
-DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
-				PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_ANY_ID, PCI_ANY_ID,
+			       PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
 
 
 static const struct dmi_system_id msi_k8t_dmi_table[] = {
@@ -824,3 +825,23 @@
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7910, rs690_fix_64bit_dma);
 
 #endif
+
+#ifdef CONFIG_AMD_NB
+
+#define AMD_15B8_RCC_DEV2_EPF0_STRAP2                                  0x10136008
+#define AMD_15B8_RCC_DEV2_EPF0_STRAP2_NO_SOFT_RESET_DEV2_F0_MASK       0x00000080L
+
+static void quirk_clear_strap_no_soft_reset_dev2_f0(struct pci_dev *dev)
+{
+	u32 data;
+
+	if (!amd_smn_read(0, AMD_15B8_RCC_DEV2_EPF0_STRAP2, &data)) {
+		data &= ~AMD_15B8_RCC_DEV2_EPF0_STRAP2_NO_SOFT_RESET_DEV2_F0_MASK;
+		if (amd_smn_write(0, AMD_15B8_RCC_DEV2_EPF0_STRAP2, data))
+			pci_err(dev, "Failed to write data 0x%x\n", data);
+	} else {
+		pci_err(dev, "Failed to read data\n");
+	}
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15b8, quirk_clear_strap_no_soft_reset_dev2_f0);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/intel_mid_pci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/intel_mid_pci.c
@@ -233,9 +233,9 @@
 		return 0;
 
 	ret = pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &gsi);
-	if (ret < 0) {
+	if (ret) {
 		dev_warn(&dev->dev, "Failed to read interrupt line: %d\n", ret);
-		return ret;
+		return pcibios_err_to_errno(ret);
 	}
 
 	id = x86_match_cpu(intel_mid_cpu_ids);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/irq.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/irq.c
@@ -253,6 +253,15 @@
 	pc_conf_set(reg, x);
 }
 
+/*
+ * FinALi pirq rules are as follows:
+ *
+ * - bit 0 selects between INTx Routing Table Mapping Registers,
+ *
+ * - bit 3 selects the nibble within the INTx Routing Table Mapping Register,
+ *
+ * - bits 7:4 map to bits 3:0 of the PCI INTx Sensitivity Register.
+ */
 static int pirq_finali_get(struct pci_dev *router, struct pci_dev *dev,
 			   int pirq)
 {
@@ -260,11 +269,13 @@
 		0, 9, 3, 10, 4, 5, 7, 6, 0, 11, 0, 12, 0, 14, 0, 15
 	};
 	unsigned long flags;
+	u8 index;
 	u8 x;
 
+	index = (pirq & 1) << 1 | (pirq & 8) >> 3;
 	raw_spin_lock_irqsave(&pc_conf_lock, flags);
 	pc_conf_set(PC_CONF_FINALI_LOCK, PC_CONF_FINALI_LOCK_KEY);
-	x = irqmap[read_pc_conf_nybble(PC_CONF_FINALI_PCI_INTX_RT1, pirq - 1)];
+	x = irqmap[read_pc_conf_nybble(PC_CONF_FINALI_PCI_INTX_RT1, index)];
 	pc_conf_set(PC_CONF_FINALI_LOCK, 0);
 	raw_spin_unlock_irqrestore(&pc_conf_lock, flags);
 	return x;
@@ -278,13 +289,15 @@
 	};
 	u8 val = irqmap[irq];
 	unsigned long flags;
+	u8 index;
 
 	if (!val)
 		return 0;
 
+	index = (pirq & 1) << 1 | (pirq & 8) >> 3;
 	raw_spin_lock_irqsave(&pc_conf_lock, flags);
 	pc_conf_set(PC_CONF_FINALI_LOCK, PC_CONF_FINALI_LOCK_KEY);
-	write_pc_conf_nybble(PC_CONF_FINALI_PCI_INTX_RT1, pirq - 1, val);
+	write_pc_conf_nybble(PC_CONF_FINALI_PCI_INTX_RT1, index, val);
 	pc_conf_set(PC_CONF_FINALI_LOCK, 0);
 	raw_spin_unlock_irqrestore(&pc_conf_lock, flags);
 	return 1;
@@ -293,7 +306,7 @@
 static int pirq_finali_lvl(struct pci_dev *router, struct pci_dev *dev,
 			   int pirq, int irq)
 {
-	u8 mask = ~(1u << (pirq - 1));
+	u8 mask = ~((pirq & 0xf0u) >> 4);
 	unsigned long flags;
 	u8 trig;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/pci/xen.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/pci/xen.c
@@ -37,10 +37,10 @@
 	u8 gsi;
 
 	rc = pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &gsi);
-	if (rc < 0) {
+	if (rc) {
 		dev_warn(&dev->dev, "Xen PCI: failed to read interrupt line: %d\n",
 			 rc);
-		return rc;
+		return pcibios_err_to_errno(rc);
 	}
 	/* In PV DomU the Xen PCI backend puts the PIRQ in the interrupt line.*/
 	pirq = gsi;
@@ -472,7 +472,6 @@
 			xen_msi_ops.setup_msi_irqs = xen_setup_msi_irqs;
 		}
 		xen_msi_ops.teardown_msi_irqs = xen_pv_teardown_msi_irqs;
-		pci_msi_ignore_mask = 1;
 	} else if (xen_hvm_domain()) {
 		xen_msi_ops.setup_msi_irqs = xen_hvm_setup_msi_irqs;
 		xen_msi_ops.teardown_msi_irqs = xen_teardown_msi_irqs;
@@ -486,6 +485,11 @@
 	 * in allocating the native domain and never use it.
 	 */
 	x86_init.irqs.create_pci_msi_domain = xen_create_pci_msi_domain;
+	/*
+	 * With XEN PIRQ/Eventchannels in use PCI/MSI[-X] masking is solely
+	 * controlled by the hypervisor.
+	 */
+	pci_msi_ignore_mask = 1;
 }
 
 #else /* CONFIG_PCI_MSI */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/Makefile
@@ -3,5 +3,6 @@
 KASAN_SANITIZE := n
 GCOV_PROFILE := n
 
-obj-$(CONFIG_EFI) 		+= quirks.o efi.o efi_$(BITS).o efi_stub_$(BITS).o
+obj-$(CONFIG_EFI) 		+= memmap.o quirks.o efi.o efi_$(BITS).o \
+				   efi_stub_$(BITS).o
 obj-$(CONFIG_EFI_MIXED)		+= efi_thunk_$(BITS).o
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/efi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/efi.c
@@ -234,9 +234,11 @@
 	data.desc_size		= e->efi_memdesc_size;
 	data.desc_version	= e->efi_memdesc_version;
 
-	rv = efi_memmap_init_early(&data);
-	if (rv)
-		return rv;
+	if (!efi_enabled(EFI_PARAVIRT)) {
+		rv = efi_memmap_init_early(&data);
+		if (rv)
+			return rv;
+	}
 
 	if (add_efi_memmap || do_efi_soft_reserve())
 		do_add_efi_memmap();
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/efi_stub_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/efi_stub_32.S
@@ -56,5 +56,5 @@
 
 	movl	16(%esp), %ebx
 	leave
-	ret
+	RET
 SYM_FUNC_END(efi_call_svam)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/efi_stub_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/efi_stub_64.S
@@ -23,5 +23,5 @@
 	mov %rsi, %rcx
 	CALL_NOSPEC rdi
 	leave
-	ret
+	RET
 SYM_FUNC_END(__efi_call)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/efi_thunk_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/efi_thunk_64.S
@@ -22,6 +22,7 @@
 #include <linux/linkage.h>
 #include <asm/page_types.h>
 #include <asm/segment.h>
+#include <asm/nospec-branch.h>
 
 	.text
 	.code64
@@ -63,7 +64,9 @@
 1:	movq	24(%rsp), %rsp
 	pop	%rbx
 	pop	%rbp
-	retq
+	ANNOTATE_UNRET_SAFE
+	ret
+	int3
 
 	.code32
 2:	pushl	$__KERNEL_CS
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/memmap.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/memmap.c
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common EFI memory map functions.
+ */
+
+#define pr_fmt(fmt) "efi: " fmt
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/efi.h>
+#include <linux/io.h>
+#include <asm/early_ioremap.h>
+#include <asm/efi.h>
+#include <linux/memblock.h>
+#include <linux/slab.h>
+
+static phys_addr_t __init __efi_memmap_alloc_early(unsigned long size)
+{
+	return memblock_phys_alloc(size, SMP_CACHE_BYTES);
+}
+
+static phys_addr_t __init __efi_memmap_alloc_late(unsigned long size)
+{
+	unsigned int order = get_order(size);
+	struct page *p = alloc_pages(GFP_KERNEL, order);
+
+	if (!p)
+		return 0;
+
+	return PFN_PHYS(page_to_pfn(p));
+}
+
+void __init __efi_memmap_free(u64 phys, unsigned long size, unsigned long flags)
+{
+	if (flags & EFI_MEMMAP_MEMBLOCK) {
+		if (slab_is_available())
+			memblock_free_late(phys, size);
+		else
+			memblock_free(phys, size);
+	} else if (flags & EFI_MEMMAP_SLAB) {
+		struct page *p = pfn_to_page(PHYS_PFN(phys));
+		unsigned int order = get_order(size);
+
+		free_pages((unsigned long) page_address(p), order);
+	}
+}
+
+/**
+ * efi_memmap_alloc - Allocate memory for the EFI memory map
+ * @num_entries: Number of entries in the allocated map.
+ * @data: efi memmap installation parameters
+ *
+ * Depending on whether mm_init() has already been invoked or not,
+ * either memblock or "normal" page allocation is used.
+ *
+ * Returns zero on success, a negative error code on failure.
+ */
+int __init efi_memmap_alloc(unsigned int num_entries,
+		struct efi_memory_map_data *data)
+{
+	/* Expect allocation parameters are zero initialized */
+	WARN_ON(data->phys_map || data->size);
+
+	data->size = num_entries * efi.memmap.desc_size;
+	data->desc_version = efi.memmap.desc_version;
+	data->desc_size = efi.memmap.desc_size;
+	data->flags &= ~(EFI_MEMMAP_SLAB | EFI_MEMMAP_MEMBLOCK);
+	data->flags |= efi.memmap.flags & EFI_MEMMAP_LATE;
+
+	if (slab_is_available()) {
+		data->flags |= EFI_MEMMAP_SLAB;
+		data->phys_map = __efi_memmap_alloc_late(data->size);
+	} else {
+		data->flags |= EFI_MEMMAP_MEMBLOCK;
+		data->phys_map = __efi_memmap_alloc_early(data->size);
+	}
+
+	if (!data->phys_map)
+		return -ENOMEM;
+	return 0;
+}
+
+/**
+ * efi_memmap_install - Install a new EFI memory map in efi.memmap
+ * @ctx: map allocation parameters (address, size, flags)
+ *
+ * Unlike efi_memmap_init_*(), this function does not allow the caller
+ * to switch from early to late mappings. It simply uses the existing
+ * mapping function and installs the new memmap.
+ *
+ * Returns zero on success, a negative error code on failure.
+ */
+int __init efi_memmap_install(struct efi_memory_map_data *data)
+{
+	unsigned long size = efi.memmap.desc_size * efi.memmap.nr_map;
+	unsigned long flags = efi.memmap.flags;
+	u64 phys = efi.memmap.phys_map;
+	int ret;
+
+	efi_memmap_unmap();
+
+	if (efi_enabled(EFI_PARAVIRT))
+		return 0;
+
+	ret = __efi_memmap_init(data);
+	if (ret)
+		return ret;
+
+	__efi_memmap_free(phys, size, flags);
+	return 0;
+}
+
+/**
+ * efi_memmap_split_count - Count number of additional EFI memmap entries
+ * @md: EFI memory descriptor to split
+ * @range: Address range (start, end) to split around
+ *
+ * Returns the number of additional EFI memmap entries required to
+ * accommodate @range.
+ */
+int __init efi_memmap_split_count(efi_memory_desc_t *md, struct range *range)
+{
+	u64 m_start, m_end;
+	u64 start, end;
+	int count = 0;
+
+	start = md->phys_addr;
+	end = start + (md->num_pages << EFI_PAGE_SHIFT) - 1;
+
+	/* modifying range */
+	m_start = range->start;
+	m_end = range->end;
+
+	if (m_start <= start) {
+		/* split into 2 parts */
+		if (start < m_end && m_end < end)
+			count++;
+	}
+
+	if (start < m_start && m_start < end) {
+		/* split into 3 parts */
+		if (m_end < end)
+			count += 2;
+		/* split into 2 parts */
+		if (end <= m_end)
+			count++;
+	}
+
+	return count;
+}
+
+/**
+ * efi_memmap_insert - Insert a memory region in an EFI memmap
+ * @old_memmap: The existing EFI memory map structure
+ * @buf: Address of buffer to store new map
+ * @mem: Memory map entry to insert
+ *
+ * It is suggested that you call efi_memmap_split_count() first
+ * to see how large @buf needs to be.
+ */
+void __init efi_memmap_insert(struct efi_memory_map *old_memmap, void *buf,
+			      struct efi_mem_range *mem)
+{
+	u64 m_start, m_end, m_attr;
+	efi_memory_desc_t *md;
+	u64 start, end;
+	void *old, *new;
+
+	/* modifying range */
+	m_start = mem->range.start;
+	m_end = mem->range.end;
+	m_attr = mem->attribute;
+
+	/*
+	 * The EFI memory map deals with regions in EFI_PAGE_SIZE
+	 * units. Ensure that the region described by 'mem' is aligned
+	 * correctly.
+	 */
+	if (!IS_ALIGNED(m_start, EFI_PAGE_SIZE) ||
+	    !IS_ALIGNED(m_end + 1, EFI_PAGE_SIZE)) {
+		WARN_ON(1);
+		return;
+	}
+
+	for (old = old_memmap->map, new = buf;
+	     old < old_memmap->map_end;
+	     old += old_memmap->desc_size, new += old_memmap->desc_size) {
+
+		/* copy original EFI memory descriptor */
+		memcpy(new, old, old_memmap->desc_size);
+		md = new;
+		start = md->phys_addr;
+		end = md->phys_addr + (md->num_pages << EFI_PAGE_SHIFT) - 1;
+
+		if (m_start <= start && end <= m_end)
+			md->attribute |= m_attr;
+
+		if (m_start <= start &&
+		    (start < m_end && m_end < end)) {
+			/* first part */
+			md->attribute |= m_attr;
+			md->num_pages = (m_end - md->phys_addr + 1) >>
+				EFI_PAGE_SHIFT;
+			/* latter part */
+			new += old_memmap->desc_size;
+			memcpy(new, old, old_memmap->desc_size);
+			md = new;
+			md->phys_addr = m_end + 1;
+			md->num_pages = (end - md->phys_addr + 1) >>
+				EFI_PAGE_SHIFT;
+		}
+
+		if ((start < m_start && m_start < end) && m_end < end) {
+			/* first part */
+			md->num_pages = (m_start - md->phys_addr) >>
+				EFI_PAGE_SHIFT;
+			/* middle part */
+			new += old_memmap->desc_size;
+			memcpy(new, old, old_memmap->desc_size);
+			md = new;
+			md->attribute |= m_attr;
+			md->phys_addr = m_start;
+			md->num_pages = (m_end - m_start + 1) >>
+				EFI_PAGE_SHIFT;
+			/* last part */
+			new += old_memmap->desc_size;
+			memcpy(new, old, old_memmap->desc_size);
+			md = new;
+			md->phys_addr = m_end + 1;
+			md->num_pages = (end - m_end) >>
+				EFI_PAGE_SHIFT;
+		}
+
+		if ((start < m_start && m_start < end) &&
+		    (end <= m_end)) {
+			/* first part */
+			md->num_pages = (m_start - md->phys_addr) >>
+				EFI_PAGE_SHIFT;
+			/* latter part */
+			new += old_memmap->desc_size;
+			memcpy(new, old, old_memmap->desc_size);
+			md = new;
+			md->phys_addr = m_start;
+			md->num_pages = (end - md->phys_addr + 1) >>
+				EFI_PAGE_SHIFT;
+			md->attribute |= m_attr;
+		}
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/efi/quirks.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/efi/quirks.c
@@ -277,7 +277,8 @@
 		return;
 	}
 
-	new = early_memremap(data.phys_map, data.size);
+	new = early_memremap_prot(data.phys_map, data.size,
+				  pgprot_val(pgprot_encrypted(FIXMAP_PAGE_NORMAL)));
 	if (!new) {
 		pr_err("Failed to map new boot services memmap\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/intel/iosf_mbi.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/intel/iosf_mbi.c
@@ -62,7 +62,7 @@
 
 fail_read:
 	dev_err(&mbi_pdev->dev, "PCI config access failed with %d\n", result);
-	return result;
+	return pcibios_err_to_errno(result);
 }
 
 static int iosf_mbi_pci_write_mdr(u32 mcrx, u32 mcr, u32 mdr)
@@ -91,7 +91,7 @@
 
 fail_write:
 	dev_err(&mbi_pdev->dev, "PCI config access failed with %d\n", result);
-	return result;
+	return pcibios_err_to_errno(result);
 }
 
 int iosf_mbi_read(u8 port, u8 opcode, u32 offset, u32 *mdr)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/olpc/olpc-xo1-sci.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/olpc/olpc-xo1-sci.c
@@ -80,7 +80,7 @@
 		return;
 	}
 
-	if (!!test_bit(SW_TABLET_MODE, ebook_switch_idev->sw) == state)
+	if (test_bit(SW_TABLET_MODE, ebook_switch_idev->sw) == !!state)
 		return; /* Nothing new to report. */
 
 	input_report_switch(ebook_switch_idev, SW_TABLET_MODE, state);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/platform/olpc/xo1-wakeup.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/platform/olpc/xo1-wakeup.S
@@ -77,7 +77,7 @@
 	pushfl
 	popl saved_context_eflags
 
-	ret
+	RET
 
 restore_registers:
 	movl saved_context_ebp, %ebp
@@ -88,7 +88,7 @@
 	pushl saved_context_eflags
 	popfl
 
-	ret
+	RET
 
 SYM_CODE_START(do_olpc_suspend_lowlevel)
 	call	save_processor_state
@@ -109,7 +109,7 @@
 
 	call	restore_registers
 	call	restore_processor_state
-	ret
+	RET
 SYM_CODE_END(do_olpc_suspend_lowlevel)
 
 .data
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/power/cpu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/power/cpu.c
@@ -20,11 +20,12 @@
 #include <asm/page.h>
 #include <asm/mce.h>
 #include <asm/suspend.h>
-#include <asm/fpu/internal.h>
+#include <asm/fpu/api.h>
 #include <asm/debugreg.h>
 #include <asm/cpu.h>
 #include <asm/mmu_context.h>
 #include <asm/cpu_device_id.h>
+#include <asm/microcode.h>
 
 #ifdef CONFIG_X86_32
 __visible unsigned long saved_context_ebx;
@@ -40,7 +41,8 @@
 	struct saved_msr *end = msr + ctxt->saved_msrs.num;
 
 	while (msr < end) {
-		msr->valid = !rdmsrl_safe(msr->info.msr_no, &msr->info.reg.q);
+		if (msr->valid)
+			rdmsrl(msr->info.msr_no, msr->info.reg.q);
 		msr++;
 	}
 }
@@ -261,11 +263,18 @@
 	x86_platform.restore_sched_clock_state();
 	mtrr_bp_restore();
 	perf_restore_debug_store();
-	msr_restore_context(ctxt);
 
 	c = &cpu_data(smp_processor_id());
 	if (cpu_has(c, X86_FEATURE_MSR_IA32_FEAT_CTL))
 		init_ia32_feat_ctl(c);
+
+	microcode_bsp_resume();
+
+	/*
+	 * This needs to happen after the microcode has been updated upon resume
+	 * because some of the MSRs are "emulated" in microcode.
+	 */
+	msr_restore_context(ctxt);
 }
 
 /* Needed by apm.c */
@@ -424,8 +433,10 @@
 	}
 
 	for (i = saved_msrs->num, j = 0; i < total_num; i++, j++) {
+		u64 dummy;
+
 		msr_array[i].info.msr_no	= msr_id[j];
-		msr_array[i].valid		= false;
+		msr_array[i].valid		= !rdmsrl_safe(msr_id[j], &dummy);
 		msr_array[i].info.reg.q		= 0;
 	}
 	saved_msrs->num   = total_num;
@@ -500,10 +511,32 @@
 	return ret;
 }
 
+static void pm_save_spec_msr(void)
+{
+	struct msr_enumeration {
+		u32 msr_no;
+		u32 feature;
+	} msr_enum[] = {
+		{ MSR_IA32_SPEC_CTRL,	 X86_FEATURE_MSR_SPEC_CTRL },
+		{ MSR_IA32_TSX_CTRL,	 X86_FEATURE_MSR_TSX_CTRL },
+		{ MSR_TSX_FORCE_ABORT,	 X86_FEATURE_TSX_FORCE_ABORT },
+		{ MSR_IA32_MCU_OPT_CTRL, X86_FEATURE_SRBDS_CTRL },
+		{ MSR_AMD64_LS_CFG,	 X86_FEATURE_LS_CFG_SSBD },
+		{ MSR_AMD64_DE_CFG,	 X86_FEATURE_LFENCE_RDTSC },
+	};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(msr_enum); i++) {
+		if (boot_cpu_has(msr_enum[i].feature))
+			msr_build_context(&msr_enum[i].msr_no, 1);
+	}
+}
+
 static int pm_check_save_msr(void)
 {
 	dmi_check_system(msr_save_dmi_table);
 	pm_cpu_check(msr_save_cpu_table);
+	pm_save_spec_msr();
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/power/hibernate_asm_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/power/hibernate_asm_32.S
@@ -32,7 +32,7 @@
 	FRAME_BEGIN
 	call swsusp_save
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(swsusp_arch_suspend)
 
 SYM_CODE_START(restore_image)
@@ -108,5 +108,5 @@
 	/* tell the hibernation core that we've just restored the memory */
 	movl	%eax, in_suspend
 
-	ret
+	RET
 SYM_FUNC_END(restore_registers)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/power/hibernate_asm_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/power/hibernate_asm_64.S
@@ -66,7 +66,7 @@
 	/* tell the hibernation core that we've just restored the memory */
 	movq	%rax, in_suspend(%rip)
 
-	ret
+	RET
 SYM_FUNC_END(restore_registers)
 
 SYM_FUNC_START(swsusp_arch_suspend)
@@ -96,7 +96,7 @@
 	FRAME_BEGIN
 	call swsusp_save
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(swsusp_arch_suspend)
 
 SYM_FUNC_START(restore_image)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/purgatory/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/purgatory/Makefile
@@ -14,6 +14,15 @@
 
 CFLAGS_sha256.o := -D__DISABLE_EXPORTS
 
+# When profile-guided optimization is enabled, llvm emits two different
+# overlapping text sections, which is not supported by kexec. Remove profile
+# optimization flags.
+KBUILD_CFLAGS := $(filter-out -fprofile-sample-use=% -fprofile-use=%,$(KBUILD_CFLAGS))
+
+# When LTO is enabled, llvm emits many text sections, which is not supported
+# by kexec. Remove -flto=* flags.
+KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_LTO),$(KBUILD_CFLAGS))
+
 # When linking purgatory.ro with -r unresolved symbols are not checked,
 # also link a purgatory.chk binary without -r to check for unresolved symbols.
 PURGATORY_LDFLAGS := -e purgatory_start -nostdlib -z nodefaultlib
@@ -32,7 +41,8 @@
 # make up the standalone purgatory.ro
 
 PURGATORY_CFLAGS_REMOVE := -mcmodel=kernel
-PURGATORY_CFLAGS := -mcmodel=large -ffreestanding -fno-zero-initialized-in-bss -g0
+PURGATORY_CFLAGS := -mcmodel=small -ffreestanding -fno-zero-initialized-in-bss -g0
+PURGATORY_CFLAGS += -fpic -fvisibility=hidden
 PURGATORY_CFLAGS += $(DISABLE_STACKLEAK_PLUGIN) -DDISABLE_BRANCH_PROFILING
 PURGATORY_CFLAGS += -fno-stack-protector
 
@@ -64,8 +74,7 @@
 CFLAGS_REMOVE_string.o		+= $(PURGATORY_CFLAGS_REMOVE)
 CFLAGS_string.o			+= $(PURGATORY_CFLAGS)
 
-AFLAGS_REMOVE_setup-x86_$(BITS).o	+= -Wa,-gdwarf-2
-AFLAGS_REMOVE_entry64.o			+= -Wa,-gdwarf-2
+asflags-remove-y		+= -g -Wa,-gdwarf-2
 
 $(obj)/purgatory.ro: $(PURGATORY_OBJS) FORCE
 		$(call if_changed,ld)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/realmode/init.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/realmode/init.c
@@ -17,6 +17,32 @@
 /* Hold the pgd entry used on booting additional CPUs */
 pgd_t trampoline_pgd_entry;
 
+void load_trampoline_pgtable(void)
+{
+#ifdef CONFIG_X86_32
+	load_cr3(initial_page_table);
+#else
+	/*
+	 * This function is called before exiting to real-mode and that will
+	 * fail with CR4.PCIDE still set.
+	 */
+	if (boot_cpu_has(X86_FEATURE_PCID))
+		cr4_clear_bits(X86_CR4_PCIDE);
+
+	write_cr3(real_mode_header->trampoline_pgd);
+#endif
+
+	/*
+	 * The CR3 write above will not flush global TLB entries.
+	 * Stale, global entries from previous page tables may still be
+	 * present.  Flush those stale entries.
+	 *
+	 * This ensures that memory accessed while running with
+	 * trampoline_pgd is *actually* mapped into trampoline_pgd.
+	 */
+	__flush_tlb_all();
+}
+
 void __init reserve_real_mode(void)
 {
 	phys_addr_t mem;
@@ -72,6 +98,7 @@
 #ifdef CONFIG_X86_64
 	u64 *trampoline_pgd;
 	u64 efer;
+	int i;
 #endif
 
 	base = (unsigned char *)real_mode_header;
@@ -128,8 +155,17 @@
 	trampoline_header->flags = 0;
 
 	trampoline_pgd = (u64 *) __va(real_mode_header->trampoline_pgd);
+
+	/* Map the real mode stub as virtual == physical */
 	trampoline_pgd[0] = trampoline_pgd_entry.pgd;
-	trampoline_pgd[511] = init_top_pgt[511].pgd;
+
+	/*
+	 * Include the entirety of the kernel mapping into the trampoline
+	 * PGD.  This way, all mappings present in the normal kernel page
+	 * tables are usable while running on trampoline_pgd.
+	 */
+	for (i = pgd_index(__PAGE_OFFSET); i < PTRS_PER_PGD; i++)
+		trampoline_pgd[i] = init_top_pgt[i].pgd;
 #endif
 
 	sme_sev_setup_real_mode(trampoline_header);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/realmode/rm/trampoline_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/realmode/rm/trampoline_32.S
@@ -23,6 +23,7 @@
 #include <linux/linkage.h>
 #include <asm/segment.h>
 #include <asm/page_types.h>
+#include <asm/nospec-branch.h>
 #include "realmode.h"
 
 	.text
@@ -59,6 +60,7 @@
 	.section ".text32","ax"
 	.code32
 SYM_CODE_START(startup_32)			# note: also used from wakeup_asm.S
+	ANNOTATE_RETPOLINE_SAFE
 	jmp	*%eax
 SYM_CODE_END(startup_32)
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/tools/relocs.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/tools/relocs.c
@@ -599,6 +599,14 @@
 		if (!(sec_applies->shdr.sh_flags & SHF_ALLOC)) {
 			continue;
 		}
+		/*
+		 * Do not perform relocations in .notes section; any
+		 * values there are meant for pre-boot consumption (e.g.
+		 * startup_xen).
+		 */
+		if (sec_applies->shdr.sh_type == SHT_NOTE) {
+			continue;
+		}
 		sh_symtab  = sec_symtab->symtab;
 		sym_strtab = sec_symtab->link->strtab;
 		for (j = 0; j < sec->shdr.sh_size/sizeof(Elf_Rel); j++) {
@@ -684,6 +692,15 @@
 		if (!(sec_applies->shdr.sh_flags & SHF_ALLOC)) {
 			continue;
 		}
+
+		/*
+		 * Do not perform relocations in .notes sections; any
+		 * values there are meant for pre-boot consumption (e.g.
+		 * startup_xen).
+		 */
+		if (sec_applies->shdr.sh_type == SHT_NOTE)
+			continue;
+
 		sh_symtab = sec_symtab->symtab;
 		sym_strtab = sec_symtab->link->strtab;
 		for (j = 0; j < sec->shdr.sh_size/sizeof(Elf_Rel); j++) {
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/Makefile
@@ -28,7 +28,8 @@
 
 obj-y += syscalls_64.o vdso/
 
-subarch-y = ../lib/csum-partial_64.o ../lib/memcpy_64.o ../entry/thunk_64.o
+subarch-y = ../lib/csum-partial_64.o ../lib/memcpy_64.o
+subarch-$(CONFIG_PREEMPTION) += ../entry/thunk_64.o
 
 endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/checksum_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/checksum_32.S
@@ -110,7 +110,7 @@
 7:	
 	popl %ebx
 	popl %esi
-	ret
+	RET
 
 #else
 
@@ -208,7 +208,7 @@
 80: 
 	popl %ebx
 	popl %esi
-	ret
+	RET
 				
 #endif
 	EXPORT_SYMBOL(csum_partial)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/ldt.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/ldt.c
@@ -23,9 +23,11 @@
 {
 	long res;
 	void *stub_addr;
+
+	BUILD_BUG_ON(sizeof(*desc) % sizeof(long));
+
 	res = syscall_stub_data(mm_idp, (unsigned long *)desc,
-				(sizeof(*desc) + sizeof(long) - 1) &
-				    ~(sizeof(long) - 1),
+				sizeof(*desc) / sizeof(long),
 				addr, &stub_addr);
 	if (!res) {
 		unsigned long args[] = { func,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/setjmp_32.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/setjmp_32.S
@@ -34,7 +34,7 @@
 	movl %esi,12(%edx)
 	movl %edi,16(%edx)
 	movl %ecx,20(%edx)		# Return address
-	ret
+	RET
 
 	.size kernel_setjmp,.-kernel_setjmp
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/setjmp_64.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/setjmp_64.S
@@ -33,7 +33,7 @@
 	movq %r14,40(%rdi)
 	movq %r15,48(%rdi)
 	movq %rsi,56(%rdi)		# Return address
-	ret
+	RET
 
 	.size kernel_setjmp,.-kernel_setjmp
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/shared/sysdep/syscalls_32.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/shared/sysdep/syscalls_32.h
@@ -6,10 +6,9 @@
 #include <asm/unistd.h>
 #include <sysdep/ptrace.h>
 
-typedef long syscall_handler_t(struct pt_regs);
+typedef long syscall_handler_t(struct syscall_args);
 
 extern syscall_handler_t *sys_call_table[];
 
 #define EXECUTE_SYSCALL(syscall, regs) \
-	((long (*)(struct syscall_args)) \
-	 (*sys_call_table[syscall]))(SYSCALL_ARGS(&regs->regs))
+	((*sys_call_table[syscall]))(SYSCALL_ARGS(&regs->regs))
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/shared/sysdep/syscalls_64.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/shared/sysdep/syscalls_64.h
@@ -10,13 +10,12 @@
 #include <linux/msg.h>
 #include <linux/shm.h>
 
-typedef long syscall_handler_t(void);
+typedef long syscall_handler_t(long, long, long, long, long, long);
 
 extern syscall_handler_t *sys_call_table[];
 
 #define EXECUTE_SYSCALL(syscall, regs) \
-	(((long (*)(long, long, long, long, long, long)) \
-	  (*sys_call_table[syscall]))(UPT_SYSCALL_ARG1(&regs->regs), \
+	(((*sys_call_table[syscall]))(UPT_SYSCALL_ARG1(&regs->regs), \
 		 		      UPT_SYSCALL_ARG2(&regs->regs), \
 				      UPT_SYSCALL_ARG3(&regs->regs), \
 				      UPT_SYSCALL_ARG4(&regs->regs), \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/syscalls_64.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/syscalls_64.c
@@ -11,6 +11,7 @@
 #include <linux/uaccess.h>
 #include <asm/prctl.h> /* XXX This should get the constants from libc */
 #include <os.h>
+#include <registers.h>
 
 long arch_prctl(struct task_struct *task, int option,
 		unsigned long __user *arg2)
@@ -35,7 +36,7 @@
 	switch (option) {
 	case ARCH_SET_FS:
 	case ARCH_SET_GS:
-		ret = restore_registers(pid, &current->thread.regs.regs);
+		ret = restore_pid_registers(pid, &current->thread.regs.regs);
 		if (ret)
 			return ret;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/tls_32.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/tls_32.c
@@ -65,9 +65,6 @@
 	struct thread_struct *t = &task->thread;
 	int idx;
 
-	if (!t->arch.tls_array)
-		return GDT_ENTRY_TLS_MIN;
-
 	for (idx = 0; idx < GDT_ENTRY_TLS_ENTRIES; idx++)
 		if (!t->arch.tls_array[idx].present)
 			return idx + GDT_ENTRY_TLS_MIN;
@@ -240,9 +237,6 @@
 {
 	struct thread_struct *t = &task->thread;
 
-	if (!t->arch.tls_array)
-		goto clear;
-
 	if (idx < GDT_ENTRY_TLS_MIN || idx > GDT_ENTRY_TLS_MAX)
 		return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/vdso/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/vdso/Makefile
@@ -62,7 +62,7 @@
 		       -Wl,-T,$(filter %.lds,$^) $(filter %.o,$^) && \
 		 sh $(srctree)/$(src)/checkundef.sh '$(NM)' '$@'
 
-VDSO_LDFLAGS = -fPIC -shared -Wl,--hash-style=sysv
+VDSO_LDFLAGS = -fPIC -shared -Wl,--hash-style=sysv -z noexecstack
 GCOV_PROFILE := n
 
 #
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/um/vdso/um_vdso.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/um/vdso/um_vdso.c
@@ -17,8 +17,10 @@
 {
 	long ret;
 
-	asm("syscall" : "=a" (ret) :
-		"0" (__NR_clock_gettime), "D" (clock), "S" (ts) : "memory");
+	asm("syscall"
+		: "=a" (ret)
+		: "0" (__NR_clock_gettime), "D" (clock), "S" (ts)
+		: "rcx", "r11", "memory");
 
 	return ret;
 }
@@ -29,8 +31,10 @@
 {
 	long ret;
 
-	asm("syscall" : "=a" (ret) :
-		"0" (__NR_gettimeofday), "D" (tv), "S" (tz) : "memory");
+	asm("syscall"
+		: "=a" (ret)
+		: "0" (__NR_gettimeofday), "D" (tv), "S" (tz)
+		: "rcx", "r11", "memory");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/Makefile
@@ -45,7 +45,7 @@
 
 obj-$(CONFIG_XEN_DEBUG_FS)	+= debugfs.o
 
-obj-$(CONFIG_XEN_PV_DOM0)	+= vga.o
+obj-$(CONFIG_XEN_DOM0)		+= vga.o
 
 obj-$(CONFIG_SWIOTLB_XEN)	+= pci-swiotlb-xen.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/enlighten.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/enlighten.c
@@ -5,6 +5,7 @@
 #endif
 #include <linux/console.h>
 #include <linux/cpu.h>
+#include <linux/instrumentation.h>
 #include <linux/kexec.h>
 #include <linux/slab.h>
 #include <linux/panic_notifier.h>
@@ -25,7 +26,8 @@
 #include "smp.h"
 #include "pmu.h"
 
-EXPORT_SYMBOL_GPL(hypercall_page);
+DEFINE_STATIC_CALL(xen_hypercall, xen_hypercall_hvm);
+EXPORT_STATIC_CALL_TRAMP(xen_hypercall);
 
 /*
  * Pointer to the xen_vcpu_info structure or
@@ -99,6 +101,67 @@
  */
 int xen_have_vcpu_info_placement = 1;
 
+static __ref void xen_get_vendor(void)
+{
+	init_cpu_devs();
+	cpu_detect(&boot_cpu_data);
+	get_cpu_vendor(&boot_cpu_data);
+}
+
+void xen_hypercall_setfunc(void)
+{
+	if (static_call_query(xen_hypercall) != xen_hypercall_hvm)
+		return;
+
+	if ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
+	     boot_cpu_data.x86_vendor == X86_VENDOR_HYGON))
+		static_call_update(xen_hypercall, xen_hypercall_amd);
+	else
+		static_call_update(xen_hypercall, xen_hypercall_intel);
+}
+
+/*
+ * Evaluate processor vendor in order to select the correct hypercall
+ * function for HVM/PVH guests.
+ * Might be called very early in boot before vendor has been set by
+ * early_cpu_init().
+ */
+noinstr void *__xen_hypercall_setfunc(void)
+{
+	void (*func)(void);
+
+	/*
+	 * Xen is supported only on CPUs with CPUID, so testing for
+	 * X86_FEATURE_CPUID is a test for early_cpu_init() having been
+	 * run.
+	 *
+	 * Note that __xen_hypercall_setfunc() is noinstr only due to a nasty
+	 * dependency chain: it is being called via the xen_hypercall static
+	 * call when running as a PVH or HVM guest. Hypercalls need to be
+	 * noinstr due to PV guests using hypercalls in noinstr code. So we
+	 * can safely tag the function body as "instrumentation ok", since
+	 * the PV guest requirement is not of interest here (xen_get_vendor()
+	 * calls noinstr functions, and static_call_update_early() might do
+	 * so, too).
+	 */
+	instrumentation_begin();
+
+	if (!boot_cpu_has(X86_FEATURE_CPUID))
+		xen_get_vendor();
+
+	if ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
+	     boot_cpu_data.x86_vendor == X86_VENDOR_HYGON))
+		func = xen_hypercall_amd;
+	else
+		func = xen_hypercall_intel;
+
+	static_call_update_early(xen_hypercall, func);
+
+	instrumentation_end();
+
+	return func;
+}
+
 static int xen_cpu_up_online(unsigned int cpu)
 {
 	xen_init_lock_cpu(cpu);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/enlighten_hvm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/enlighten_hvm.c
@@ -101,15 +101,8 @@
 	/* PVH set up hypercall page in xen_prepare_pvh(). */
 	if (xen_pvh_domain())
 		pv_info.name = "Xen PVH";
-	else {
-		u64 pfn;
-		uint32_t msr;
-
+	else
 		pv_info.name = "Xen HVM";
-		msr = cpuid_ebx(base + 2);
-		pfn = __pa(hypercall_page);
-		wrmsr_safe(msr, (u32)pfn, (u32)(pfn >> 32));
-	}
 
 	xen_setup_features();
 
@@ -284,6 +277,10 @@
 	if (xen_pv_domain())
 		return 0;
 
+	/* Set correct hypercall function. */
+	if (xen_domain)
+		xen_hypercall_setfunc();
+
 	if (xen_pvh_domain() && nopv) {
 		/* Guest booting via the Xen-PVH boot entry goes here */
 		pr_info("\"nopv\" parameter is ignored in PVH guest\n");
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/enlighten_pv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/enlighten_pv.c
@@ -609,7 +609,7 @@
 	TRAP_ENTRY(exc_int3,				false ),
 	TRAP_ENTRY(exc_overflow,			false ),
 #ifdef CONFIG_IA32_EMULATION
-	{ entry_INT80_compat,          xen_entry_INT80_compat,          false },
+	TRAP_ENTRY(int80_emulation,			false ),
 #endif
 	TRAP_ENTRY(exc_page_fault,			false ),
 	TRAP_ENTRY(exc_divide_error,			false ),
@@ -759,6 +759,7 @@
 {
 	static DEFINE_SPINLOCK(lock);
 	static struct trap_info traps[257];
+	static const struct trap_info zero = { };
 	unsigned out;
 
 	trace_xen_cpu_load_idt(desc);
@@ -768,7 +769,7 @@
 	memcpy(this_cpu_ptr(&idt_desc), desc, sizeof(idt_desc));
 
 	out = xen_convert_trap_info(desc, traps, false);
-	memset(&traps[out], 0, sizeof(traps[0]));
+	traps[out] = zero;
 
 	xen_mc_flush();
 	if (HYPERVISOR_set_trap_table(traps))
@@ -1206,6 +1207,9 @@
 
 	xen_domain_type = XEN_PV_DOMAIN;
 	xen_start_flags = xen_start_info->flags;
+	/* Interrupts are guaranteed to be off initially. */
+	early_boot_irqs_disabled = true;
+	static_call_update_early(xen_hypercall, xen_hypercall_pv);
 
 	xen_setup_features();
 
@@ -1303,7 +1307,6 @@
 	WARN_ON(xen_cpuhp_setup(xen_cpu_up_prepare_pv, xen_cpu_dead_pv));
 
 	local_irq_disable();
-	early_boot_irqs_disabled = true;
 
 	xen_raw_console_write("mapping kernel into physical memory\n");
 	xen_setup_kernel_pagetable((pgd_t *)xen_start_info->pt_base,
@@ -1352,7 +1355,8 @@
 
 		x86_platform.set_legacy_features =
 				xen_dom0_set_legacy_features;
-		xen_init_vga(info, xen_start_info->console.dom0.info_size);
+		xen_init_vga(info, xen_start_info->console.dom0.info_size,
+			     &boot_params.screen_info);
 		xen_start_info->console.domU.mfn = 0;
 		xen_start_info->console.domU.evtchn = 0;
 
@@ -1364,10 +1368,6 @@
 
 		xen_acpi_sleep_register();
 
-		/* Avoid searching for BIOS MP tables */
-		x86_init.mpparse.find_smp_config = x86_init_noop;
-		x86_init.mpparse.get_smp_config = x86_init_uint_noop;
-
 		xen_boot_params_init_edd();
 
 #ifdef CONFIG_ACPI
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/enlighten_pvh.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/enlighten_pvh.c
@@ -27,22 +27,28 @@
 
 void __init xen_pvh_init(struct boot_params *boot_params)
 {
-	u32 msr;
-	u64 pfn;
-
 	xen_pvh = 1;
 	xen_domain_type = XEN_HVM_DOMAIN;
 	xen_start_flags = pvh_start_info.flags;
 
-	msr = cpuid_ebx(xen_cpuid_base() + 2);
-	pfn = __pa(hypercall_page);
-	wrmsr_safe(msr, (u32)pfn, (u32)(pfn >> 32));
-
 	if (xen_initial_domain())
 		x86_init.oem.arch_setup = xen_add_preferred_consoles;
 	x86_init.oem.banner = xen_banner;
 
 	xen_efi_init(boot_params);
+
+	if (xen_initial_domain()) {
+		struct xen_platform_op op = {
+			.cmd = XENPF_get_dom0_console,
+		};
+		int ret = HYPERVISOR_platform_op(&op);
+
+		if (ret > 0)
+			xen_init_vga(&op.u.dom0_console,
+				     min(ret * sizeof(char),
+					 sizeof(op.u.dom0_console)),
+				     &boot_params->screen_info);
+	}
 }
 
 void __init mem_map_via_hcall(struct boot_params *boot_params_p)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/mmu_pv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/mmu_pv.c
@@ -95,6 +95,51 @@
  */
 static DEFINE_SPINLOCK(xen_reservation_lock);
 
+/* Protected by xen_reservation_lock. */
+#define MIN_CONTIG_ORDER 9 /* 2MB */
+static unsigned int discontig_frames_order = MIN_CONTIG_ORDER;
+static unsigned long discontig_frames_early[1UL << MIN_CONTIG_ORDER] __initdata;
+static unsigned long *discontig_frames __refdata = discontig_frames_early;
+static bool discontig_frames_dyn;
+
+static int alloc_discontig_frames(unsigned int order)
+{
+	unsigned long *new_array, *old_array;
+	unsigned int old_order;
+	unsigned long flags;
+
+	BUG_ON(order < MIN_CONTIG_ORDER);
+	BUILD_BUG_ON(sizeof(discontig_frames_early) != PAGE_SIZE);
+
+	new_array = (unsigned long *)__get_free_pages(GFP_KERNEL,
+						      order - MIN_CONTIG_ORDER);
+	if (!new_array)
+		return -ENOMEM;
+
+	spin_lock_irqsave(&xen_reservation_lock, flags);
+
+	old_order = discontig_frames_order;
+
+	if (order > discontig_frames_order || !discontig_frames_dyn) {
+		if (!discontig_frames_dyn)
+			old_array = NULL;
+		else
+			old_array = discontig_frames;
+
+		discontig_frames = new_array;
+		discontig_frames_order = order;
+		discontig_frames_dyn = true;
+	} else {
+		old_array = new_array;
+	}
+
+	spin_unlock_irqrestore(&xen_reservation_lock, flags);
+
+	free_pages((unsigned long)old_array, old_order - MIN_CONTIG_ORDER);
+
+	return 0;
+}
+
 /*
  * Note about cr3 (pagetable base) values:
  *
@@ -762,6 +807,7 @@
 {
 	struct page *page;
 
+	spin_lock(&init_mm.page_table_lock);
 	spin_lock(&pgd_lock);
 
 	list_for_each_entry(page, &pgd_list, lru) {
@@ -772,6 +818,7 @@
 	}
 
 	spin_unlock(&pgd_lock);
+	spin_unlock(&init_mm.page_table_lock);
 }
 
 static void __init xen_mark_pinned(struct mm_struct *mm, struct page *page,
@@ -791,6 +838,9 @@
 	static_branch_enable(&xen_struct_pages_ready);
 	SetPagePinned(virt_to_page(level3_user_vsyscall));
 	xen_pgd_walk(&init_mm, xen_mark_pinned, FIXADDR_TOP);
+
+	if (alloc_discontig_frames(MIN_CONTIG_ORDER))
+		BUG();
 }
 
 static void xen_unpin_page(struct mm_struct *mm, struct page *page,
@@ -866,6 +916,7 @@
 {
 	struct page *page;
 
+	spin_lock(&init_mm.page_table_lock);
 	spin_lock(&pgd_lock);
 
 	list_for_each_entry(page, &pgd_list, lru) {
@@ -877,6 +928,7 @@
 	}
 
 	spin_unlock(&pgd_lock);
+	spin_unlock(&init_mm.page_table_lock);
 }
 
 static void xen_activate_mm(struct mm_struct *prev, struct mm_struct *next)
@@ -2151,10 +2203,6 @@
 	memset(dummy_mapping, 0xff, PAGE_SIZE);
 }
 
-/* Protected by xen_reservation_lock. */
-#define MAX_CONTIG_ORDER 9 /* 2MB */
-static unsigned long discontig_frames[1<<MAX_CONTIG_ORDER];
-
 #define VOID_PTE (mfn_pte(0, __pgprot(0)))
 static void xen_zap_pfn_range(unsigned long vaddr, unsigned int order,
 				unsigned long *in_frames,
@@ -2271,24 +2319,25 @@
 				 unsigned int address_bits,
 				 dma_addr_t *dma_handle)
 {
-	unsigned long *in_frames = discontig_frames, out_frame;
+	unsigned long *in_frames, out_frame;
 	unsigned long  flags;
 	int            success;
 	unsigned long vstart = (unsigned long)phys_to_virt(pstart);
 
-	/*
-	 * Currently an auto-translated guest will not perform I/O, nor will
-	 * it require PAE page directories below 4GB. Therefore any calls to
-	 * this function are redundant and can be ignored.
-	 */
+	if (unlikely(order > discontig_frames_order)) {
+		if (!discontig_frames_dyn)
+			return -ENOMEM;
 
-	if (unlikely(order > MAX_CONTIG_ORDER))
-		return -ENOMEM;
+		if (alloc_discontig_frames(order))
+			return -ENOMEM;
+	}
 
 	memset((void *) vstart, 0, PAGE_SIZE << order);
 
 	spin_lock_irqsave(&xen_reservation_lock, flags);
 
+	in_frames = discontig_frames;
+
 	/* 1. Zap current PTEs, remembering MFNs. */
 	xen_zap_pfn_range(vstart, order, in_frames, NULL);
 
@@ -2312,12 +2361,12 @@
 
 void xen_destroy_contiguous_region(phys_addr_t pstart, unsigned int order)
 {
-	unsigned long *out_frames = discontig_frames, in_frame;
+	unsigned long *out_frames, in_frame;
 	unsigned long  flags;
 	int success;
 	unsigned long vstart;
 
-	if (unlikely(order > MAX_CONTIG_ORDER))
+	if (unlikely(order > discontig_frames_order))
 		return;
 
 	vstart = (unsigned long)phys_to_virt(pstart);
@@ -2325,6 +2374,8 @@
 
 	spin_lock_irqsave(&xen_reservation_lock, flags);
 
+	out_frames = discontig_frames;
+
 	/* 1. Find start MFN of contiguous extent. */
 	in_frame = virt_to_mfn(vstart);
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/p2m.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/p2m.c
@@ -197,7 +197,7 @@
 static void __ref free_p2m_page(void *p)
 {
 	if (unlikely(!slab_is_available())) {
-		memblock_free((unsigned long)p, PAGE_SIZE);
+		memblock_free_ptr(p, PAGE_SIZE);
 		return;
 	}
 
@@ -736,7 +736,7 @@
 		 * immediate unmapping.
 		 */
 		map_ops[i].status = GNTST_general_error;
-		unmap[0].host_addr = map_ops[i].host_addr,
+		unmap[0].host_addr = map_ops[i].host_addr;
 		unmap[0].handle = map_ops[i].handle;
 		map_ops[i].handle = INVALID_GRANT_HANDLE;
 		if (map_ops[i].flags & GNTMAP_device_map)
@@ -746,7 +746,7 @@
 
 		if (kmap_ops) {
 			kmap_ops[i].status = GNTST_general_error;
-			unmap[1].host_addr = kmap_ops[i].host_addr,
+			unmap[1].host_addr = kmap_ops[i].host_addr;
 			unmap[1].handle = kmap_ops[i].handle;
 			kmap_ops[i].handle = INVALID_GRANT_HANDLE;
 			if (kmap_ops[i].flags & GNTMAP_device_map)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/pmu.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/pmu.c
@@ -512,10 +512,7 @@
 	return ret;
 }
 
-bool is_xen_pmu(int cpu)
-{
-	return (get_xenpmu_data() != NULL);
-}
+bool is_xen_pmu;
 
 void xen_pmu_init(int cpu)
 {
@@ -526,7 +523,7 @@
 
 	BUILD_BUG_ON(sizeof(struct xen_pmu_data) > PAGE_SIZE);
 
-	if (xen_hvm_domain())
+	if (xen_hvm_domain() || (cpu != 0 && !is_xen_pmu))
 		return;
 
 	xenpmu_data = (struct xen_pmu_data *)get_zeroed_page(GFP_KERNEL);
@@ -547,7 +544,8 @@
 	per_cpu(xenpmu_shared, cpu).xenpmu_data = xenpmu_data;
 	per_cpu(xenpmu_shared, cpu).flags = 0;
 
-	if (cpu == 0) {
+	if (!is_xen_pmu) {
+		is_xen_pmu = true;
 		perf_register_guest_info_callbacks(&xen_guest_cbs);
 		xen_pmu_arch_init();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/pmu.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/pmu.h
@@ -4,6 +4,8 @@
 
 #include <xen/interface/xenpmu.h>
 
+extern bool is_xen_pmu;
+
 irqreturn_t xen_pmu_irq_handler(int irq, void *dev_id);
 #ifdef CONFIG_XEN_HAVE_VPMU
 void xen_pmu_init(int cpu);
@@ -12,7 +14,6 @@
 static inline void xen_pmu_init(int cpu) {}
 static inline void xen_pmu_finish(int cpu) {}
 #endif
-bool is_xen_pmu(int cpu);
 bool pmu_msr_read(unsigned int msr, uint64_t *val, int *err);
 bool pmu_msr_write(unsigned int msr, uint32_t low, uint32_t high, int *err);
 int pmu_apic_update(uint32_t reg);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/setup.c
@@ -856,7 +856,7 @@
 	 * to relocating (and even reusing) pages with kernel text or data.
 	 */
 	if (xen_is_e820_reserved(__pa_symbol(_text),
-			__pa_symbol(__bss_stop) - __pa_symbol(_text))) {
+				 __pa_symbol(_end) - __pa_symbol(_text))) {
 		xen_raw_console_write("Xen hypervisor allocated kernel memory conflicts with E820 map\n");
 		BUG();
 	}
@@ -922,7 +922,7 @@
 	if (!boot_cpu_has(sysenter_feature))
 		return;
 
-	ret = register_callback(CALLBACKTYPE_sysenter, xen_sysenter_target);
+	ret = register_callback(CALLBACKTYPE_sysenter, xen_entry_SYSENTER_compat);
 	if(ret != 0)
 		setup_clear_cpu_cap(sysenter_feature);
 }
@@ -931,7 +931,7 @@
 {
 	int ret;
 
-	ret = register_callback(CALLBACKTYPE_syscall, xen_syscall_target);
+	ret = register_callback(CALLBACKTYPE_syscall, xen_entry_SYSCALL_64);
 	if (ret != 0) {
 		printk(KERN_ERR "Failed to set syscall callback: %d\n", ret);
 		/* Pretty fatal; 64-bit userspace has no other
@@ -940,7 +940,7 @@
 
 	if (boot_cpu_has(X86_FEATURE_SYSCALL32)) {
 		ret = register_callback(CALLBACKTYPE_syscall32,
-					xen_syscall32_target);
+					xen_entry_SYSCALL_compat);
 		if (ret != 0)
 			setup_clear_cpu_cap(X86_FEATURE_SYSCALL32);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/smp.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/smp.c
@@ -32,30 +32,30 @@
 
 void xen_smp_intr_free(unsigned int cpu)
 {
+	kfree(per_cpu(xen_resched_irq, cpu).name);
+	per_cpu(xen_resched_irq, cpu).name = NULL;
 	if (per_cpu(xen_resched_irq, cpu).irq >= 0) {
 		unbind_from_irqhandler(per_cpu(xen_resched_irq, cpu).irq, NULL);
 		per_cpu(xen_resched_irq, cpu).irq = -1;
-		kfree(per_cpu(xen_resched_irq, cpu).name);
-		per_cpu(xen_resched_irq, cpu).name = NULL;
 	}
+	kfree(per_cpu(xen_callfunc_irq, cpu).name);
+	per_cpu(xen_callfunc_irq, cpu).name = NULL;
 	if (per_cpu(xen_callfunc_irq, cpu).irq >= 0) {
 		unbind_from_irqhandler(per_cpu(xen_callfunc_irq, cpu).irq, NULL);
 		per_cpu(xen_callfunc_irq, cpu).irq = -1;
-		kfree(per_cpu(xen_callfunc_irq, cpu).name);
-		per_cpu(xen_callfunc_irq, cpu).name = NULL;
 	}
+	kfree(per_cpu(xen_debug_irq, cpu).name);
+	per_cpu(xen_debug_irq, cpu).name = NULL;
 	if (per_cpu(xen_debug_irq, cpu).irq >= 0) {
 		unbind_from_irqhandler(per_cpu(xen_debug_irq, cpu).irq, NULL);
 		per_cpu(xen_debug_irq, cpu).irq = -1;
-		kfree(per_cpu(xen_debug_irq, cpu).name);
-		per_cpu(xen_debug_irq, cpu).name = NULL;
 	}
+	kfree(per_cpu(xen_callfuncsingle_irq, cpu).name);
+	per_cpu(xen_callfuncsingle_irq, cpu).name = NULL;
 	if (per_cpu(xen_callfuncsingle_irq, cpu).irq >= 0) {
 		unbind_from_irqhandler(per_cpu(xen_callfuncsingle_irq, cpu).irq,
 				       NULL);
 		per_cpu(xen_callfuncsingle_irq, cpu).irq = -1;
-		kfree(per_cpu(xen_callfuncsingle_irq, cpu).name);
-		per_cpu(xen_callfuncsingle_irq, cpu).name = NULL;
 	}
 }
 
@@ -65,6 +65,9 @@
 	char *resched_name, *callfunc_name, *debug_name;
 
 	resched_name = kasprintf(GFP_KERNEL, "resched%d", cpu);
+	if (!resched_name)
+		goto fail_mem;
+	per_cpu(xen_resched_irq, cpu).name = resched_name;
 	rc = bind_ipi_to_irqhandler(XEN_RESCHEDULE_VECTOR,
 				    cpu,
 				    xen_reschedule_interrupt,
@@ -74,9 +77,11 @@
 	if (rc < 0)
 		goto fail;
 	per_cpu(xen_resched_irq, cpu).irq = rc;
-	per_cpu(xen_resched_irq, cpu).name = resched_name;
 
 	callfunc_name = kasprintf(GFP_KERNEL, "callfunc%d", cpu);
+	if (!callfunc_name)
+		goto fail_mem;
+	per_cpu(xen_callfunc_irq, cpu).name = callfunc_name;
 	rc = bind_ipi_to_irqhandler(XEN_CALL_FUNCTION_VECTOR,
 				    cpu,
 				    xen_call_function_interrupt,
@@ -86,10 +91,13 @@
 	if (rc < 0)
 		goto fail;
 	per_cpu(xen_callfunc_irq, cpu).irq = rc;
-	per_cpu(xen_callfunc_irq, cpu).name = callfunc_name;
 
 	if (!xen_fifo_events) {
 		debug_name = kasprintf(GFP_KERNEL, "debug%d", cpu);
+		if (!debug_name)
+			goto fail_mem;
+
+		per_cpu(xen_debug_irq, cpu).name = debug_name;
 		rc = bind_virq_to_irqhandler(VIRQ_DEBUG, cpu,
 					     xen_debug_interrupt,
 					     IRQF_PERCPU | IRQF_NOBALANCING,
@@ -97,10 +105,13 @@
 		if (rc < 0)
 			goto fail;
 		per_cpu(xen_debug_irq, cpu).irq = rc;
-		per_cpu(xen_debug_irq, cpu).name = debug_name;
 	}
 
 	callfunc_name = kasprintf(GFP_KERNEL, "callfuncsingle%d", cpu);
+	if (!callfunc_name)
+		goto fail_mem;
+
+	per_cpu(xen_callfuncsingle_irq, cpu).name = callfunc_name;
 	rc = bind_ipi_to_irqhandler(XEN_CALL_FUNCTION_SINGLE_VECTOR,
 				    cpu,
 				    xen_call_function_single_interrupt,
@@ -110,10 +121,11 @@
 	if (rc < 0)
 		goto fail;
 	per_cpu(xen_callfuncsingle_irq, cpu).irq = rc;
-	per_cpu(xen_callfuncsingle_irq, cpu).name = callfunc_name;
 
 	return 0;
 
+ fail_mem:
+	rc = -ENOMEM;
  fail:
 	xen_smp_intr_free(cpu);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/smp_hvm.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/smp_hvm.c
@@ -20,6 +20,12 @@
 	xen_vcpu_setup(0);
 
 	/*
+	 * Called again in case the kernel boots on vcpu >= MAX_VIRT_CPUS.
+	 * Refer to comments in xen_hvm_init_time_ops().
+	 */
+	xen_hvm_init_time_ops();
+
+	/*
 	 * The alternative logic (which patches the unlock/lock) runs before
 	 * the smp bootup up code is activated. Hence we need to set this up
 	 * the core kernel is being patched. Otherwise we will have only
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/smp_pv.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/smp_pv.c
@@ -63,6 +63,7 @@
 
 	cr4_init();
 	cpu_init();
+	fpu__init_cpu();
 	touch_softlockup_watchdog();
 
 	/* PVH runs in ring 0 and allows us to do native syscalls. Yay! */
@@ -97,18 +98,18 @@
 
 void xen_smp_intr_free_pv(unsigned int cpu)
 {
+	kfree(per_cpu(xen_irq_work, cpu).name);
+	per_cpu(xen_irq_work, cpu).name = NULL;
 	if (per_cpu(xen_irq_work, cpu).irq >= 0) {
 		unbind_from_irqhandler(per_cpu(xen_irq_work, cpu).irq, NULL);
 		per_cpu(xen_irq_work, cpu).irq = -1;
-		kfree(per_cpu(xen_irq_work, cpu).name);
-		per_cpu(xen_irq_work, cpu).name = NULL;
 	}
 
+	kfree(per_cpu(xen_pmu_irq, cpu).name);
+	per_cpu(xen_pmu_irq, cpu).name = NULL;
 	if (per_cpu(xen_pmu_irq, cpu).irq >= 0) {
 		unbind_from_irqhandler(per_cpu(xen_pmu_irq, cpu).irq, NULL);
 		per_cpu(xen_pmu_irq, cpu).irq = -1;
-		kfree(per_cpu(xen_pmu_irq, cpu).name);
-		per_cpu(xen_pmu_irq, cpu).name = NULL;
 	}
 }
 
@@ -118,6 +119,7 @@
 	char *callfunc_name, *pmu_name;
 
 	callfunc_name = kasprintf(GFP_KERNEL, "irqwork%d", cpu);
+	per_cpu(xen_irq_work, cpu).name = callfunc_name;
 	rc = bind_ipi_to_irqhandler(XEN_IRQ_WORK_VECTOR,
 				    cpu,
 				    xen_irq_work_interrupt,
@@ -127,10 +129,10 @@
 	if (rc < 0)
 		goto fail;
 	per_cpu(xen_irq_work, cpu).irq = rc;
-	per_cpu(xen_irq_work, cpu).name = callfunc_name;
 
-	if (is_xen_pmu(cpu)) {
+	if (is_xen_pmu) {
 		pmu_name = kasprintf(GFP_KERNEL, "pmu%d", cpu);
+		per_cpu(xen_pmu_irq, cpu).name = pmu_name;
 		rc = bind_virq_to_irqhandler(VIRQ_XENPMU, cpu,
 					     xen_pmu_irq_handler,
 					     IRQF_PERCPU|IRQF_NOBALANCING,
@@ -138,7 +140,6 @@
 		if (rc < 0)
 			goto fail;
 		per_cpu(xen_pmu_irq, cpu).irq = rc;
-		per_cpu(xen_pmu_irq, cpu).name = pmu_name;
 	}
 
 	return 0;
@@ -148,28 +149,12 @@
 	return rc;
 }
 
-static void __init xen_fill_possible_map(void)
-{
-	int i, rc;
-
-	if (xen_initial_domain())
-		return;
-
-	for (i = 0; i < nr_cpu_ids; i++) {
-		rc = HYPERVISOR_vcpu_op(VCPUOP_is_up, i, NULL);
-		if (rc >= 0) {
-			num_processors++;
-			set_cpu_possible(i, true);
-		}
-	}
-}
-
-static void __init xen_filter_cpu_maps(void)
+static void __init _get_smp_config(unsigned int early)
 {
 	int i, rc;
 	unsigned int subtract = 0;
 
-	if (!xen_initial_domain())
+	if (early)
 		return;
 
 	num_processors = 0;
@@ -210,7 +195,6 @@
 		 * sure the old memory can be recycled. */
 		make_lowmem_page_readwrite(xen_initial_gdt);
 
-	xen_filter_cpu_maps();
 	xen_setup_vcpu_info_placement();
 
 	/*
@@ -486,5 +470,8 @@
 void __init xen_smp_init(void)
 {
 	smp_ops = xen_smp_ops;
-	xen_fill_possible_map();
+
+	/* Avoid searching for BIOS MP tables */
+	x86_init.mpparse.find_smp_config = x86_init_noop;
+	x86_init.mpparse.get_smp_config = _get_smp_config;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/spinlock.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/spinlock.c
@@ -75,6 +75,7 @@
 	     cpu, per_cpu(lock_kicker_irq, cpu));
 
 	name = kasprintf(GFP_KERNEL, "spinlock%d", cpu);
+	per_cpu(irq_name, cpu) = name;
 	irq = bind_ipi_to_irqhandler(XEN_SPIN_UNLOCK_VECTOR,
 				     cpu,
 				     dummy_handler,
@@ -85,7 +86,6 @@
 	if (irq >= 0) {
 		disable_irq(irq); /* make sure it's never delivered */
 		per_cpu(lock_kicker_irq, cpu) = irq;
-		per_cpu(irq_name, cpu) = name;
 	}
 
 	printk("cpu %d spinlock event irq %d\n", cpu, irq);
@@ -98,6 +98,8 @@
 	if (!xen_pvspin)
 		return;
 
+	kfree(per_cpu(irq_name, cpu));
+	per_cpu(irq_name, cpu) = NULL;
 	/*
 	 * When booting the kernel with 'mitigations=auto,nosmt', the secondary
 	 * CPUs are not activated, and lock_kicker_irq is not initialized.
@@ -108,8 +110,6 @@
 
 	unbind_from_irqhandler(irq, NULL);
 	per_cpu(lock_kicker_irq, cpu) = -1;
-	kfree(per_cpu(irq_name, cpu));
-	per_cpu(irq_name, cpu) = NULL;
 }
 
 PV_CALLEE_SAVE_REGS_THUNK(xen_vcpu_stolen);
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/time.c
@@ -474,15 +474,51 @@
 	xen_clocksource.vdso_clock_mode = VDSO_CLOCKMODE_PVCLOCK;
 }
 
+/*
+ * Check if it is possible to safely use the tsc as a clocksource.  This is
+ * only true if the hypervisor notifies the guest that its tsc is invariant,
+ * the tsc is stable, and the tsc instruction will never be emulated.
+ */
+static int __init xen_tsc_safe_clocksource(void)
+{
+	u32 eax, ebx, ecx, edx;
+
+	if (!(boot_cpu_has(X86_FEATURE_CONSTANT_TSC)))
+		return 0;
+
+	if (!(boot_cpu_has(X86_FEATURE_NONSTOP_TSC)))
+		return 0;
+
+	if (check_tsc_unstable())
+		return 0;
+
+	/* Leaf 4, sub-leaf 0 (0x40000x03) */
+	cpuid_count(xen_cpuid_base() + 3, 0, &eax, &ebx, &ecx, &edx);
+
+	/* tsc_mode = no_emulate (2) */
+	if (ebx != 2)
+		return 0;
+
+	return 1;
+}
+
 static void __init xen_time_init(void)
 {
 	struct pvclock_vcpu_time_info *pvti;
 	int cpu = smp_processor_id();
 	struct timespec64 tp;
 
-	/* As Dom0 is never moved, no penalty on using TSC there */
+	/*
+	 * As Dom0 is never moved, no penalty on using TSC there.
+	 *
+	 * If it is possible for the guest to determine that the tsc is a safe
+	 * clocksource, then set xen_clocksource rating below that of the tsc
+	 * so that the system prefers tsc instead.
+	 */
 	if (xen_initial_domain())
 		xen_clocksource.rating = 275;
+	else if (xen_tsc_safe_clocksource())
+		xen_clocksource.rating = 299;
 
 	clocksource_register_hz(&xen_clocksource, NSEC_PER_SEC);
 
@@ -558,6 +594,11 @@
 
 void __init xen_hvm_init_time_ops(void)
 {
+	static bool hvm_time_initialized;
+
+	if (hvm_time_initialized)
+		return;
+
 	/*
 	 * vector callback is needed otherwise we cannot receive interrupts
 	 * on cpu > 0 and at this point we don't know how many cpus are
@@ -567,7 +608,22 @@
 		return;
 
 	if (!xen_feature(XENFEAT_hvm_safe_pvclock)) {
-		pr_info("Xen doesn't support pvclock on HVM, disable pv timer");
+		pr_info_once("Xen doesn't support pvclock on HVM, disable pv timer");
+		return;
+	}
+
+	/*
+	 * Only MAX_VIRT_CPUS 'vcpu_info' are embedded inside 'shared_info'.
+	 * The __this_cpu_read(xen_vcpu) is still NULL when Xen HVM guest
+	 * boots on vcpu >= MAX_VIRT_CPUS (e.g., kexec), To access
+	 * __this_cpu_read(xen_vcpu) via xen_clocksource_read() will panic.
+	 *
+	 * The xen_hvm_init_time_ops() should be called again later after
+	 * __this_cpu_read(xen_vcpu) is available.
+	 */
+	if (!__this_cpu_read(xen_vcpu)) {
+		pr_info("Delay xen_init_time_common() as kernel is running on vcpu=%d\n",
+			xen_vcpu_nr(0));
 		return;
 	}
 
@@ -577,6 +633,8 @@
 	x86_cpuinit.setup_percpu_clockev = xen_hvm_setup_cpu_clockevents;
 
 	x86_platform.set_wallclock = xen_set_wallclock;
+
+	hvm_time_initialized = true;
 }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/vga.c
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/vga.c
@@ -9,10 +9,9 @@
 
 #include "xen-ops.h"
 
-void __init xen_init_vga(const struct dom0_vga_console_info *info, size_t size)
+void __init xen_init_vga(const struct dom0_vga_console_info *info, size_t size,
+			 struct screen_info *screen_info)
 {
-	struct screen_info *screen_info = &boot_params.screen_info;
-
 	/* This is drawn from a dump from vgacon:startup in
 	 * standard Linux. */
 	screen_info->orig_video_mode = 3;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/xen-asm.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/xen-asm.S
@@ -20,6 +20,29 @@
 
 #include <linux/init.h>
 #include <linux/linkage.h>
+#include <linux/objtool.h>
+#include <../entry/calling.h>
+
+/*
+ * PV hypercall interface to the hypervisor.
+ *
+ * Called via inline asm(), so better preserve %rcx and %r11.
+ *
+ * Input:
+ *	%eax: hypercall number
+ *	%rdi, %rsi, %rdx, %r10, %r8: args 1..5 for the hypercall
+ * Output: %rax
+ */
+SYM_FUNC_START(xen_hypercall_pv)
+	push %rcx
+	push %r11
+	UNWIND_HINT_SAVE
+	syscall
+	UNWIND_HINT_RESTORE
+	pop %r11
+	pop %rcx
+	RET
+SYM_FUNC_END(xen_hypercall_pv)
 
 /*
  * Enable events.  This clears the event mask and tests the pending
@@ -44,7 +67,7 @@
 	call check_events
 1:
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(xen_irq_enable_direct)
 
 
@@ -54,7 +77,7 @@
  */
 SYM_FUNC_START(xen_irq_disable_direct)
 	movb $1, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_mask
-	ret
+	RET
 SYM_FUNC_END(xen_irq_disable_direct)
 
 /*
@@ -70,7 +93,7 @@
 	testb $0xff, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_mask
 	setz %ah
 	addb %ah, %ah
-	ret
+	RET
 SYM_FUNC_END(xen_save_fl_direct)
 
 /*
@@ -99,7 +122,7 @@
 	pop %rcx
 	pop %rax
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(check_events)
 
 SYM_FUNC_START(xen_read_cr2)
@@ -107,19 +130,19 @@
 	_ASM_MOV PER_CPU_VAR(xen_vcpu), %_ASM_AX
 	_ASM_MOV XEN_vcpu_info_arch_cr2(%_ASM_AX), %_ASM_AX
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(xen_read_cr2);
 
 SYM_FUNC_START(xen_read_cr2_direct)
 	FRAME_BEGIN
 	_ASM_MOV PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_arch_cr2, %_ASM_AX
 	FRAME_END
-	ret
+	RET
 SYM_FUNC_END(xen_read_cr2_direct);
 
 .macro xen_pv_trap name
 SYM_CODE_START(xen_\name)
-	UNWIND_HINT_EMPTY
+	UNWIND_HINT_ENTRY
 	pop %rcx
 	pop %r11
 	jmp  \name
@@ -150,7 +173,7 @@
 #endif /* CONFIG_X86_MCE */
 xen_pv_trap asm_exc_simd_coprocessor_error
 #ifdef CONFIG_IA32_EMULATION
-xen_pv_trap entry_INT80_compat
+xen_pv_trap asm_int80_emulation
 #endif
 xen_pv_trap asm_exc_xen_unknown_trap
 xen_pv_trap asm_exc_xen_hypervisor_callback
@@ -169,7 +192,6 @@
 SYM_CODE_END(xen_early_idt_handler_array)
 	__FINIT
 
-hypercall_iret = hypercall_page + __HYPERVISOR_iret * 32
 /*
  * Xen64 iret frame:
  *
@@ -179,19 +201,49 @@
  *	cs
  *	rip		<-- standard iret frame
  *
- *	flags
+ *	flags		<-- xen_iret must push from here on
  *
- *	rcx		}
- *	r11		}<-- pushed by hypercall page
- * rsp->rax		}
+ *	rcx
+ *	r11
+ * rsp->rax
  */
+.macro xen_hypercall_iret
+	pushq $0	/* Flags */
+	push %rcx
+	push %r11
+	push %rax
+	mov  $__HYPERVISOR_iret, %eax
+	syscall		/* Do the IRET. */
+#ifdef CONFIG_SLS
+	int3
+#endif
+.endm
+
 SYM_CODE_START(xen_iret)
 	UNWIND_HINT_EMPTY
-	pushq $0
-	jmp hypercall_iret
+	xen_hypercall_iret
 SYM_CODE_END(xen_iret)
 
 /*
+ * XEN pv doesn't use trampoline stack, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is
+ * also the kernel stack.  Reusing swapgs_restore_regs_and_return_to_usermode()
+ * in XEN pv would cause %rsp to move up to the top of the kernel stack and
+ * leave the IRET frame below %rsp, which is dangerous to be corrupted if #NMI
+ * interrupts. And swapgs_restore_regs_and_return_to_usermode() pushing the IRET
+ * frame at the same address is useless.
+ */
+SYM_CODE_START(xenpv_restore_regs_and_return_to_usermode)
+	UNWIND_HINT_REGS
+	POP_REGS
+
+	/* stackleak_erase() can work safely on the kernel stack. */
+	STACKLEAK_ERASE_NOCLOBBER
+
+	addq	$8, %rsp	/* skip regs->orig_ax */
+	jmp xen_iret
+SYM_CODE_END(xenpv_restore_regs_and_return_to_usermode)
+
+/*
  * Xen handles syscall callbacks much like ordinary exceptions, which
  * means we have:
  * - kernel gs
@@ -207,8 +259,8 @@
  */
 
 /* Normal 64-bit system call target */
-SYM_CODE_START(xen_syscall_target)
-	UNWIND_HINT_EMPTY
+SYM_CODE_START(xen_entry_SYSCALL_64)
+	UNWIND_HINT_ENTRY
 	popq %rcx
 	popq %r11
 
@@ -221,13 +273,13 @@
 	movq $__USER_CS, 1*8(%rsp)
 
 	jmp entry_SYSCALL_64_after_hwframe
-SYM_CODE_END(xen_syscall_target)
+SYM_CODE_END(xen_entry_SYSCALL_64)
 
 #ifdef CONFIG_IA32_EMULATION
 
 /* 32-bit compat syscall target */
-SYM_CODE_START(xen_syscall32_target)
-	UNWIND_HINT_EMPTY
+SYM_CODE_START(xen_entry_SYSCALL_compat)
+	UNWIND_HINT_ENTRY
 	popq %rcx
 	popq %r11
 
@@ -240,11 +292,11 @@
 	movq $__USER32_CS, 1*8(%rsp)
 
 	jmp entry_SYSCALL_compat_after_hwframe
-SYM_CODE_END(xen_syscall32_target)
+SYM_CODE_END(xen_entry_SYSCALL_compat)
 
 /* 32-bit compat sysenter target */
-SYM_CODE_START(xen_sysenter_target)
-	UNWIND_HINT_EMPTY
+SYM_CODE_START(xen_entry_SYSENTER_compat)
+	UNWIND_HINT_ENTRY
 	/*
 	 * NB: Xen is polite and clears TF from EFLAGS for us.  This means
 	 * that we don't need to guard against single step exceptions here.
@@ -261,18 +313,17 @@
 	movq $__USER32_CS, 1*8(%rsp)
 
 	jmp entry_SYSENTER_compat_after_hwframe
-SYM_CODE_END(xen_sysenter_target)
+SYM_CODE_END(xen_entry_SYSENTER_compat)
 
 #else /* !CONFIG_IA32_EMULATION */
 
-SYM_CODE_START(xen_syscall32_target)
-SYM_CODE_START(xen_sysenter_target)
-	UNWIND_HINT_EMPTY
+SYM_CODE_START(xen_entry_SYSCALL_compat)
+SYM_CODE_START(xen_entry_SYSENTER_compat)
+	UNWIND_HINT_ENTRY
 	lea 16(%rsp), %rsp	/* strip %rcx, %r11 */
 	mov $-ENOSYS, %rax
-	pushq $0
-	jmp hypercall_iret
-SYM_CODE_END(xen_sysenter_target)
-SYM_CODE_END(xen_syscall32_target)
+	xen_hypercall_iret
+SYM_CODE_END(xen_entry_SYSENTER_compat)
+SYM_CODE_END(xen_entry_SYSCALL_compat)
 
 #endif	/* CONFIG_IA32_EMULATION */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/xen-head.S
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/xen-head.S
@@ -6,9 +6,11 @@
 
 #include <linux/elfnote.h>
 #include <linux/init.h>
+#include <linux/instrumentation.h>
 
 #include <asm/boot.h>
 #include <asm/asm.h>
+#include <asm/frame.h>
 #include <asm/msr.h>
 #include <asm/page_types.h>
 #include <asm/percpu.h>
@@ -64,22 +66,86 @@
 #endif
 #endif
 
-.pushsection .text
-	.balign PAGE_SIZE
-SYM_CODE_START(hypercall_page)
-	.rept (PAGE_SIZE / 32)
-		UNWIND_HINT_FUNC
-		.skip 31, 0x90
-		ret
-	.endr
-
-#define HYPERCALL(n) \
-	.equ xen_hypercall_##n, hypercall_page + __HYPERVISOR_##n * 32; \
-	.type xen_hypercall_##n, @function; .size xen_hypercall_##n, 32
-#include <asm/xen-hypercalls.h>
-#undef HYPERCALL
-SYM_CODE_END(hypercall_page)
-.popsection
+	.pushsection .text
+/*
+ * Xen hypercall interface to the hypervisor.
+ *
+ * Input:
+ *     %eax: hypercall number
+ *   32-bit:
+ *     %ebx, %ecx, %edx, %esi, %edi: args 1..5 for the hypercall
+ *   64-bit:
+ *     %rdi, %rsi, %rdx, %r10, %r8: args 1..5 for the hypercall
+ * Output: %[er]ax
+ */
+SYM_FUNC_START(xen_hypercall_hvm)
+	FRAME_BEGIN
+	/* Save all relevant registers (caller save and arguments). */
+#ifdef CONFIG_X86_32
+	push %eax
+	push %ebx
+	push %ecx
+	push %edx
+	push %esi
+	push %edi
+#else
+	push %rax
+	push %rcx
+	push %rdx
+	push %rdi
+	push %rsi
+	push %r11
+	push %r10
+	push %r9
+	push %r8
+#ifdef CONFIG_FRAME_POINTER
+	pushq $0	/* Dummy push for stack alignment. */
+#endif
+#endif
+	/* Set the vendor specific function. */
+	call __xen_hypercall_setfunc
+	/* Set ZF = 1 if AMD, Restore saved registers. */
+#ifdef CONFIG_X86_32
+	lea xen_hypercall_amd, %ebx
+	cmp %eax, %ebx
+	pop %edi
+	pop %esi
+	pop %edx
+	pop %ecx
+	pop %ebx
+	pop %eax
+#else
+	lea xen_hypercall_amd(%rip), %rcx
+	cmp %rax, %rcx
+#ifdef CONFIG_FRAME_POINTER
+	pop %rax	/* Dummy pop. */
+#endif
+	pop %r8
+	pop %r9
+	pop %r10
+	pop %r11
+	pop %rsi
+	pop %rdi
+	pop %rdx
+	pop %rcx
+	pop %rax
+#endif
+	FRAME_END
+	/* Use correct hypercall function. */
+	jz xen_hypercall_amd
+	jmp xen_hypercall_intel
+SYM_FUNC_END(xen_hypercall_hvm)
+
+SYM_FUNC_START(xen_hypercall_amd)
+	vmmcall
+	RET
+SYM_FUNC_END(xen_hypercall_amd)
+
+SYM_FUNC_START(xen_hypercall_intel)
+	vmcall
+	RET
+SYM_FUNC_END(xen_hypercall_intel)
+	.popsection
 
 	ELFNOTE(Xen, XEN_ELFNOTE_GUEST_OS,       .asciz "linux")
 	ELFNOTE(Xen, XEN_ELFNOTE_GUEST_VERSION,  .asciz "2.6")
@@ -94,7 +160,6 @@
 #ifdef CONFIG_XEN_PV
 	ELFNOTE(Xen, XEN_ELFNOTE_ENTRY,          _ASM_PTR startup_xen)
 #endif
-	ELFNOTE(Xen, XEN_ELFNOTE_HYPERCALL_PAGE, _ASM_PTR hypercall_page)
 	ELFNOTE(Xen, XEN_ELFNOTE_FEATURES,
 		.ascii "!writable_page_tables|pae_pgdir_above_4gb")
 	ELFNOTE(Xen, XEN_ELFNOTE_SUPPORTED_FEATURES,
--- linux-xilinx-zynqmp-5.15.0.orig/arch/x86/xen/xen-ops.h
+++ linux-xilinx-zynqmp-5.15.0/arch/x86/xen/xen-ops.h
@@ -10,10 +10,10 @@
 /* These are code, but not functions.  Defined in entry.S */
 extern const char xen_failsafe_callback[];
 
-void xen_sysenter_target(void);
+void xen_entry_SYSENTER_compat(void);
 #ifdef CONFIG_X86_64
-void xen_syscall_target(void);
-void xen_syscall32_target(void);
+void xen_entry_SYSCALL_64(void);
+void xen_entry_SYSCALL_compat(void);
 #endif
 
 extern void *xen_initial_gdt;
@@ -110,11 +110,12 @@
 
 struct dom0_vga_console_info;
 
-#ifdef CONFIG_XEN_PV_DOM0
-void __init xen_init_vga(const struct dom0_vga_console_info *, size_t size);
+#ifdef CONFIG_XEN_DOM0
+void __init xen_init_vga(const struct dom0_vga_console_info *, size_t size,
+			 struct screen_info *);
 #else
 static inline void __init xen_init_vga(const struct dom0_vga_console_info *info,
-				       size_t size)
+				       size_t size, struct screen_info *si)
 {
 }
 #endif
@@ -163,4 +164,13 @@
 static inline void xen_hvm_post_suspend(int suspend_cancelled) {}
 #endif
 
+#ifdef CONFIG_XEN_PV
+void xen_hypercall_pv(void);
+#endif
+void xen_hypercall_hvm(void);
+void xen_hypercall_amd(void);
+void xen_hypercall_intel(void);
+void xen_hypercall_setfunc(void);
+void *__xen_hypercall_setfunc(void);
+
 #endif /* XEN_OPS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/boot/Makefile
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/boot/Makefile
@@ -9,8 +9,7 @@
 
 
 # KBUILD_CFLAGS used when building rest of boot (takes effect recursively)
-KBUILD_CFLAGS	+= -fno-builtin -Iarch/$(ARCH)/boot/include
-HOSTFLAGS	+= -Iarch/$(ARCH)/boot/include
+KBUILD_CFLAGS	+= -fno-builtin
 
 subdir-y	:= lib
 targets		+= vmlinux.bin vmlinux.bin.gz
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi
@@ -8,19 +8,19 @@
 			reg = <0x00000000 0x08000000>;
 			bank-width = <2>;
 			device-width = <2>;
-			partition@0x0 {
+			partition@0 {
 				label = "data";
 				reg = <0x00000000 0x06000000>;
 			};
-			partition@0x6000000 {
+			partition@6000000 {
 				label = "boot loader area";
 				reg = <0x06000000 0x00800000>;
 			};
-			partition@0x6800000 {
+			partition@6800000 {
 				label = "kernel image";
 				reg = <0x06800000 0x017e0000>;
 			};
-			partition@0x7fe0000 {
+			partition@7fe0000 {
 				label = "boot environment";
 				reg = <0x07fe0000 0x00020000>;
 			};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi
@@ -8,19 +8,19 @@
 			reg = <0x08000000 0x01000000>;
 			bank-width = <2>;
 			device-width = <2>;
-			partition@0x0 {
+			partition@0 {
 				label = "boot loader area";
 				reg = <0x00000000 0x00400000>;
 			};
-			partition@0x400000 {
+			partition@400000 {
 				label = "kernel image";
 				reg = <0x00400000 0x00600000>;
 			};
-			partition@0xa00000 {
+			partition@a00000 {
 				label = "data";
 				reg = <0x00a00000 0x005e0000>;
 			};
-			partition@0xfe0000 {
+			partition@fe0000 {
 				label = "boot environment";
 				reg = <0x00fe0000 0x00020000>;
 			};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi
@@ -8,11 +8,11 @@
 			reg = <0x08000000 0x00400000>;
 			bank-width = <2>;
 			device-width = <2>;
-			partition@0x0 {
+			partition@0 {
 				label = "boot loader area";
 				reg = <0x00000000 0x003f0000>;
 			};
-			partition@0x3f0000 {
+			partition@3f0000 {
 				label = "boot environment";
 				reg = <0x003f0000 0x00010000>;
 			};
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/boot/lib/zmem.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/boot/lib/zmem.c
@@ -4,13 +4,14 @@
 /* bits taken from ppc */
 
 extern void *avail_ram, *end_avail;
+void gunzip(void *dst, int dstlen, unsigned char *src, int *lenp);
 
-void exit (void)
+static void exit(void)
 {
   for (;;);
 }
 
-void *zalloc(unsigned size)
+static void *zalloc(unsigned int size)
 {
         void *p = avail_ram;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/include/asm/core.h
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/include/asm/core.h
@@ -6,6 +6,10 @@
 
 #include <variant/core.h>
 
+#ifndef XCHAL_HAVE_DIV32
+#define XCHAL_HAVE_DIV32 0
+#endif
+
 #ifndef XCHAL_HAVE_EXCLUSIVE
 #define XCHAL_HAVE_EXCLUSIVE 0
 #endif
@@ -26,4 +30,13 @@
 #define XCHAL_SPANNING_WAY 0
 #endif
 
+#ifndef XCHAL_HW_MIN_VERSION
+#if defined(XCHAL_HW_MIN_VERSION_MAJOR) && defined(XCHAL_HW_MIN_VERSION_MINOR)
+#define XCHAL_HW_MIN_VERSION (XCHAL_HW_MIN_VERSION_MAJOR * 100 + \
+			      XCHAL_HW_MIN_VERSION_MINOR)
+#else
+#define XCHAL_HW_MIN_VERSION 0
+#endif
+#endif
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/include/asm/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/include/asm/pgtable.h
@@ -411,6 +411,10 @@
 
 typedef pte_t *pte_addr_t;
 
+void update_mmu_tlb(struct vm_area_struct *vma,
+		    unsigned long address, pte_t *ptep);
+#define __HAVE_ARCH_UPDATE_MMU_TLB
+
 #endif /* !defined (__ASSEMBLY__) */
 
 #define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/include/asm/processor.h
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/include/asm/processor.h
@@ -226,8 +226,8 @@
 
 #define xtensa_set_sr(x, sr) \
 	({ \
-	 unsigned int v = (unsigned int)(x); \
-	 __asm__ __volatile__ ("wsr %0, "__stringify(sr) :: "a"(v)); \
+	 __asm__ __volatile__ ("wsr %0, "__stringify(sr) :: \
+			       "a"((unsigned int)(x))); \
 	 })
 
 #define xtensa_get_sr(sr) \
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/include/asm/timex.h
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/include/asm/timex.h
@@ -29,10 +29,6 @@
 
 extern unsigned long ccount_freq;
 
-typedef unsigned long long cycles_t;
-
-#define get_cycles()	(0)
-
 void local_timer_setup(unsigned cpu);
 
 /*
@@ -59,4 +55,6 @@
 	xtensa_set_sr(ccompare, SREG_CCOMPARE + LINUX_TIMER);
 }
 
+#include <asm-generic/timex.h>
+
 #endif	/* _XTENSA_TIMEX_H */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/coprocessor.S
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/coprocessor.S
@@ -29,7 +29,7 @@
 	.if XTENSA_HAVE_COPROCESSOR(x);					\
 		.align 4;						\
 	.Lsave_cp_regs_cp##x:						\
-		xchal_cp##x##_store a2 a4 a5 a6 a7;			\
+		xchal_cp##x##_store a2 a3 a4 a5 a6;			\
 		jx	a0;						\
 	.endif
 
@@ -46,7 +46,7 @@
 	.if XTENSA_HAVE_COPROCESSOR(x);					\
 		.align 4;						\
 	.Lload_cp_regs_cp##x:						\
-		xchal_cp##x##_load a2 a4 a5 a6 a7;			\
+		xchal_cp##x##_load a2 a3 a4 a5 a6;			\
 		jx	a0;						\
 	.endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/jump_label.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/jump_label.c
@@ -40,7 +40,7 @@
 {
 	struct patch *patch = data;
 
-	if (atomic_inc_return(&patch->cpu_count) == 1) {
+	if (atomic_inc_return(&patch->cpu_count) == num_online_cpus()) {
 		local_patch_text(patch->addr, patch->data, patch->sz);
 		atomic_inc(&patch->cpu_count);
 	} else {
@@ -61,7 +61,7 @@
 			.data = data,
 		};
 		stop_machine_cpuslocked(patch_text_stop_machine,
-					&patch, NULL);
+					&patch, cpu_online_mask);
 	} else {
 		unsigned long flags;
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/perf_event.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/perf_event.c
@@ -13,17 +13,26 @@
 #include <linux/perf_event.h>
 #include <linux/platform_device.h>
 
+#include <asm/core.h>
 #include <asm/processor.h>
 #include <asm/stacktrace.h>
 
+#define XTENSA_HWVERSION_RG_2015_0	260000
+
+#if XCHAL_HW_MIN_VERSION >= XTENSA_HWVERSION_RG_2015_0
+#define XTENSA_PMU_ERI_BASE		0x00101000
+#else
+#define XTENSA_PMU_ERI_BASE		0x00001000
+#endif
+
 /* Global control/status for all perf counters */
-#define XTENSA_PMU_PMG			0x1000
+#define XTENSA_PMU_PMG			XTENSA_PMU_ERI_BASE
 /* Perf counter values */
-#define XTENSA_PMU_PM(i)		(0x1080 + (i) * 4)
+#define XTENSA_PMU_PM(i)		(XTENSA_PMU_ERI_BASE + 0x80 + (i) * 4)
 /* Perf counter control registers */
-#define XTENSA_PMU_PMCTRL(i)		(0x1100 + (i) * 4)
+#define XTENSA_PMU_PMCTRL(i)		(XTENSA_PMU_ERI_BASE + 0x100 + (i) * 4)
 /* Perf counter status registers */
-#define XTENSA_PMU_PMSTAT(i)		(0x1180 + (i) * 4)
+#define XTENSA_PMU_PMSTAT(i)		(XTENSA_PMU_ERI_BASE + 0x180 + (i) * 4)
 
 #define XTENSA_PMU_PMG_PMEN		0x1
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/ptrace.c
@@ -226,12 +226,12 @@
 
 void user_enable_single_step(struct task_struct *child)
 {
-	child->ptrace |= PT_SINGLESTEP;
+	set_tsk_thread_flag(child, TIF_SINGLESTEP);
 }
 
 void user_disable_single_step(struct task_struct *child)
 {
-	child->ptrace &= ~PT_SINGLESTEP;
+	clear_tsk_thread_flag(child, TIF_SINGLESTEP);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/signal.c
@@ -465,7 +465,7 @@
 		/* Set up the stack frame */
 		ret = setup_frame(&ksig, sigmask_to_save(), regs);
 		signal_setup_done(ret, &ksig, 0);
-		if (current->ptrace & PT_SINGLESTEP)
+		if (test_thread_flag(TIF_SINGLESTEP))
 			task_pt_regs(current)->icountlevel = 1;
 
 		return;
@@ -491,7 +491,7 @@
 	/* If there's no signal to deliver, we just restore the saved mask.  */
 	restore_saved_sigmask();
 
-	if (current->ptrace & PT_SINGLESTEP)
+	if (test_thread_flag(TIF_SINGLESTEP))
 		task_pt_regs(current)->icountlevel = 1;
 	return;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/time.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/time.c
@@ -154,6 +154,7 @@
 	cpu = of_find_compatible_node(NULL, NULL, "cdns,xtensa-cpu");
 	if (cpu) {
 		clk = of_clk_get(cpu, 0);
+		of_node_put(cpu);
 		if (!IS_ERR(clk)) {
 			ccount_freq = clk_get_rate(clk);
 			return;
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/kernel/traps.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/kernel/traps.c
@@ -510,7 +510,7 @@
 
 void show_stack(struct task_struct *task, unsigned long *sp, const char *loglvl)
 {
-	size_t len;
+	size_t len, off = 0;
 
 	if (!sp)
 		sp = stack_pointer(task);
@@ -519,9 +519,17 @@
 		  kstack_depth_to_print * STACK_DUMP_ENTRY_SIZE);
 
 	printk("%sStack:\n", loglvl);
-	print_hex_dump(loglvl, " ", DUMP_PREFIX_NONE,
-		       STACK_DUMP_LINE_SIZE, STACK_DUMP_ENTRY_SIZE,
-		       sp, len, false);
+	while (off < len) {
+		u8 line[STACK_DUMP_LINE_SIZE];
+		size_t line_len = len - off > STACK_DUMP_LINE_SIZE ?
+			STACK_DUMP_LINE_SIZE : len - off;
+
+		__memcpy(line, (u8 *)sp + off, line_len);
+		print_hex_dump(loglvl, " ", DUMP_PREFIX_NONE,
+			       STACK_DUMP_LINE_SIZE, STACK_DUMP_ENTRY_SIZE,
+			       line, line_len, false);
+		off += STACK_DUMP_LINE_SIZE;
+	}
 	show_trace(task, sp, loglvl);
 }
 
@@ -552,5 +560,5 @@
 	if (panic_on_oops)
 		panic("Fatal exception");
 
-	do_exit(err);
+	make_task_dead(err);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/mm/tlb.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/mm/tlb.c
@@ -162,6 +162,12 @@
 	}
 }
 
+void update_mmu_tlb(struct vm_area_struct *vma,
+		    unsigned long address, pte_t *ptep)
+{
+	local_flush_tlb_page(vma, address);
+}
+
 #ifdef CONFIG_DEBUG_TLB_SANITY
 
 static unsigned get_pte_for_vaddr(unsigned vaddr)
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/platforms/iss/console.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/platforms/iss/console.c
@@ -36,24 +36,19 @@
 static struct tty_driver *serial_driver;
 static struct tty_port serial_port;
 static DEFINE_TIMER(serial_timer, rs_poll);
-static DEFINE_SPINLOCK(timer_lock);
 
 static int rs_open(struct tty_struct *tty, struct file * filp)
 {
-	spin_lock_bh(&timer_lock);
 	if (tty->count == 1)
 		mod_timer(&serial_timer, jiffies + SERIAL_TIMER_VALUE);
-	spin_unlock_bh(&timer_lock);
 
 	return 0;
 }
 
 static void rs_close(struct tty_struct *tty, struct file * filp)
 {
-	spin_lock_bh(&timer_lock);
 	if (tty->count == 1)
 		del_timer_sync(&serial_timer);
-	spin_unlock_bh(&timer_lock);
 }
 
 
@@ -73,8 +68,6 @@
 	int rd = 1;
 	unsigned char c;
 
-	spin_lock(&timer_lock);
-
 	while (simc_poll(0)) {
 		rd = simc_read(0, &c, 1);
 		if (rd <= 0)
@@ -87,7 +80,6 @@
 		tty_flip_buffer_push(port);
 	if (rd)
 		mod_timer(&serial_timer, jiffies + SERIAL_TIMER_VALUE);
-	spin_unlock(&timer_lock);
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/platforms/iss/network.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/platforms/iss/network.c
@@ -204,7 +204,7 @@
 	return simc_write(lp->tp.info.tuntap.fd, (*skb)->data, (*skb)->len);
 }
 
-unsigned short tuntap_protocol(struct sk_buff *skb)
+static unsigned short tuntap_protocol(struct sk_buff *skb)
 {
 	return eth_type_trans(skb, skb->dev);
 }
@@ -231,7 +231,7 @@
 
 	init += sizeof(TRANSPORT_TUNTAP_NAME) - 1;
 	if (*init == ',') {
-		rem = split_if_spec(init + 1, &mac_str, &dev_name);
+		rem = split_if_spec(init + 1, &mac_str, &dev_name, NULL);
 		if (rem != NULL) {
 			pr_err("%s: extra garbage on specification : '%s'\n",
 			       dev->name, rem);
@@ -477,7 +477,7 @@
 	return -EINVAL;
 }
 
-void iss_net_user_timer_expire(struct timer_list *unused)
+static void iss_net_user_timer_expire(struct timer_list *unused)
 {
 }
 
@@ -502,16 +502,24 @@
 	.ndo_set_rx_mode	= iss_net_set_multicast_list,
 };
 
-static int iss_net_configure(int index, char *init)
+static void iss_net_pdev_release(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct iss_net_private *lp =
+		container_of(pdev, struct iss_net_private, pdev);
+
+	free_netdev(lp->dev);
+}
+
+static void iss_net_configure(int index, char *init)
 {
 	struct net_device *dev;
 	struct iss_net_private *lp;
-	int err;
 
 	dev = alloc_etherdev(sizeof(*lp));
 	if (dev == NULL) {
 		pr_err("eth_configure: failed to allocate device\n");
-		return 1;
+		return;
 	}
 
 	/* Initialize private element. */
@@ -540,7 +548,7 @@
 	if (!tuntap_probe(lp, index, init)) {
 		pr_err("%s: invalid arguments. Skipping device!\n",
 		       dev->name);
-		goto errout;
+		goto err_free_netdev;
 	}
 
 	pr_info("Netdevice %d (%pM)\n", index, dev->dev_addr);
@@ -548,7 +556,8 @@
 	/* sysfs register */
 
 	if (!driver_registered) {
-		platform_driver_register(&iss_net_driver);
+		if (platform_driver_register(&iss_net_driver))
+			goto err_free_netdev;
 		driver_registered = 1;
 	}
 
@@ -558,7 +567,9 @@
 
 	lp->pdev.id = index;
 	lp->pdev.name = DRIVER_NAME;
-	platform_device_register(&lp->pdev);
+	lp->pdev.dev.release = iss_net_pdev_release;
+	if (platform_device_register(&lp->pdev))
+		goto err_free_netdev;
 	SET_NETDEV_DEV(dev, &lp->pdev.dev);
 
 	dev->netdev_ops = &iss_netdev_ops;
@@ -567,23 +578,20 @@
 	dev->irq = -1;
 
 	rtnl_lock();
-	err = register_netdevice(dev);
-	rtnl_unlock();
-
-	if (err) {
+	if (register_netdevice(dev)) {
+		rtnl_unlock();
 		pr_err("%s: error registering net device!\n", dev->name);
-		/* XXX: should we call ->remove() here? */
-		free_netdev(dev);
-		return 1;
+		platform_device_unregister(&lp->pdev);
+		return;
 	}
+	rtnl_unlock();
 
 	timer_setup(&lp->tl, iss_net_user_timer_expire, 0);
 
-	return 0;
+	return;
 
-errout:
-	/* FIXME: unregister; free, etc.. */
-	return -EIO;
+err_free_netdev:
+	free_netdev(dev);
 }
 
 /* ------------------------------------------------------------------------- */
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/platforms/iss/simdisk.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/platforms/iss/simdisk.c
@@ -212,12 +212,18 @@
 	struct simdisk *dev = PDE_DATA(file_inode(file));
 	const char *s = dev->filename;
 	if (s) {
-		ssize_t n = simple_read_from_buffer(buf, size, ppos,
-							s, strlen(s));
-		if (n < 0)
-			return n;
-		buf += n;
-		size -= n;
+		ssize_t len = strlen(s);
+		char *temp = kmalloc(len + 2, GFP_KERNEL);
+
+		if (!temp)
+			return -ENOMEM;
+
+		len = scnprintf(temp, len + 2, "%s\n", s);
+		len = simple_read_from_buffer(buf, size, ppos,
+					      temp, len);
+
+		kfree(temp);
+		return len;
 	}
 	return simple_read_from_buffer(buf, size, ppos, "\n", 1);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/arch/xtensa/platforms/xtfpga/setup.c
+++ linux-xilinx-zynqmp-5.15.0/arch/xtensa/platforms/xtfpga/setup.c
@@ -133,6 +133,7 @@
 
 	if ((eth = of_find_compatible_node(eth, NULL, "opencores,ethoc")))
 		update_local_mac(eth);
+	of_node_put(eth);
 	return 0;
 }
 arch_initcall(machine_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/block/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/block/Kconfig
@@ -26,6 +26,18 @@
 
 if BLOCK
 
+config BLOCK_LEGACY_AUTOLOAD
+	bool "Legacy autoloading support"
+	help
+	  Enable loading modules and creating block device instances based on
+	  accesses through their device special file.  This is a historic Linux
+	  feature and makes no sense in a udev world where device files are
+	  created on demand.
+
+	  Say N here unless booting or other functionality broke without it, in
+	  which case you should also send a report to your distribution and
+	  linux-block@vger.kernel.org.
+
 config BLK_RQ_ALLOC_TIME
 	bool
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/Makefile
+++ linux-xilinx-zynqmp-5.15.0/block/Makefile
@@ -3,7 +3,7 @@
 # Makefile for the kernel block layer
 #
 
-obj-$(CONFIG_BLOCK) := bdev.o fops.o bio.o elevator.o blk-core.o blk-sysfs.o \
+obj-y		:= bdev.o fops.o bio.o elevator.o blk-core.o blk-sysfs.o \
 			blk-flush.o blk-settings.o blk-ioc.o blk-map.o \
 			blk-exec.o blk-merge.o blk-timeout.o \
 			blk-lib.o blk-mq.o blk-mq-tag.o blk-stat.o \
--- linux-xilinx-zynqmp-5.15.0.orig/block/bdev.c
+++ linux-xilinx-zynqmp-5.15.0/block/bdev.c
@@ -735,12 +735,15 @@
 	struct inode *inode;
 
 	inode = ilookup(blockdev_superblock, dev);
-	if (!inode) {
+	if (!inode && IS_ENABLED(CONFIG_BLOCK_LEGACY_AUTOLOAD)) {
 		blk_request_module(dev);
 		inode = ilookup(blockdev_superblock, dev);
-		if (!inode)
-			return NULL;
+		if (inode)
+			pr_warn_ratelimited(
+"block device autoloading is deprecated. It will be removed in Linux 5.19\n");
 	}
+	if (!inode)
+		return NULL;
 
 	/* switch from the inode reference to a device mode one: */
 	bdev = &BDEV_I(inode)->bdev;
@@ -834,7 +837,7 @@
 		 * used in blkdev_get/put().
 		 */
 		if ((mode & FMODE_WRITE) && !bdev->bd_write_holder &&
-		    (disk->flags & GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE)) {
+		    (disk->event_flags & DISK_EVENT_FLAG_BLOCK_ON_EXCL_WRITE)) {
 			bdev->bd_write_holder = true;
 			unblock_events = false;
 		}
@@ -1016,7 +1019,7 @@
 }
 EXPORT_SYMBOL(__invalidate_device);
 
-void iterate_bdevs(void (*func)(struct block_device *, void *), void *arg)
+void sync_bdevs(bool wait)
 {
 	struct inode *inode, *old_inode = NULL;
 
@@ -1047,8 +1050,19 @@
 		bdev = I_BDEV(inode);
 
 		mutex_lock(&bdev->bd_disk->open_mutex);
-		if (bdev->bd_openers)
-			func(bdev, arg);
+		if (!bdev->bd_openers) {
+			; /* skip */
+		} else if (wait) {
+			/*
+			 * We keep the error status of individual mapping so
+			 * that applications can catch the writeback error using
+			 * fsync(2). See filemap_fdatawait_keep_errors() for
+			 * details.
+			 */
+			filemap_fdatawait_keep_errors(inode->i_mapping);
+		} else {
+			filemap_fdatawrite(inode->i_mapping);
+		}
 		mutex_unlock(&bdev->bd_disk->open_mutex);
 
 		spin_lock(&blockdev_superblock->s_inode_list_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/block/bfq-cgroup.c
+++ linux-xilinx-zynqmp-5.15.0/block/bfq-cgroup.c
@@ -555,6 +555,7 @@
 				   */
 	bfqg->bfqd = bfqd;
 	bfqg->active_entities = 0;
+	bfqg->online = true;
 	bfqg->rq_pos_tree = RB_ROOT;
 }
 
@@ -583,28 +584,11 @@
 	entity->sched_data = &parent->sched_data;
 }
 
-static struct bfq_group *bfq_lookup_bfqg(struct bfq_data *bfqd,
-					 struct blkcg *blkcg)
+static void bfq_link_bfqg(struct bfq_data *bfqd, struct bfq_group *bfqg)
 {
-	struct blkcg_gq *blkg;
-
-	blkg = blkg_lookup(blkcg, bfqd->queue);
-	if (likely(blkg))
-		return blkg_to_bfqg(blkg);
-	return NULL;
-}
-
-struct bfq_group *bfq_find_set_group(struct bfq_data *bfqd,
-				     struct blkcg *blkcg)
-{
-	struct bfq_group *bfqg, *parent;
+	struct bfq_group *parent;
 	struct bfq_entity *entity;
 
-	bfqg = bfq_lookup_bfqg(bfqd, blkcg);
-
-	if (unlikely(!bfqg))
-		return NULL;
-
 	/*
 	 * Update chain of bfq_groups as we might be handling a leaf group
 	 * which, along with some of its relatives, has not been hooked yet
@@ -621,8 +605,28 @@
 			bfq_group_set_parent(curr_bfqg, parent);
 		}
 	}
+}
 
-	return bfqg;
+struct bfq_group *bfq_bio_bfqg(struct bfq_data *bfqd, struct bio *bio)
+{
+	struct blkcg_gq *blkg = bio->bi_blkg;
+	struct bfq_group *bfqg;
+
+	while (blkg) {
+		if (!blkg->online) {
+			blkg = blkg->parent;
+			continue;
+		}
+		bfqg = blkg_to_bfqg(blkg);
+		if (bfqg->online) {
+			bio_associate_blkg_from_css(bio, &blkg->blkcg->css);
+			return bfqg;
+		}
+		blkg = blkg->parent;
+	}
+	bio_associate_blkg_from_css(bio,
+				&bfqg_to_blkg(bfqd->root_group)->blkcg->css);
+	return bfqd->root_group;
 }
 
 /**
@@ -645,6 +649,12 @@
 	struct bfq_entity *entity = &bfqq->entity;
 
 	/*
+	 * oom_bfqq is not allowed to move, oom_bfqq will hold ref to root_group
+	 * until elevator exit.
+	 */
+	if (bfqq == &bfqd->oom_bfqq)
+		return;
+	/*
 	 * Get extra reference to prevent bfqq from being freed in
 	 * next possible expire or deactivate.
 	 */
@@ -698,38 +708,58 @@
  * Move bic to blkcg, assuming that bfqd->lock is held; which makes
  * sure that the reference to cgroup is valid across the call (see
  * comments in bfq_bic_update_cgroup on this issue)
- *
- * NOTE: an alternative approach might have been to store the current
- * cgroup in bfqq and getting a reference to it, reducing the lookup
- * time here, at the price of slightly more complex code.
  */
-static struct bfq_group *__bfq_bic_change_cgroup(struct bfq_data *bfqd,
-						struct bfq_io_cq *bic,
-						struct blkcg *blkcg)
+static void *__bfq_bic_change_cgroup(struct bfq_data *bfqd,
+				     struct bfq_io_cq *bic,
+				     struct bfq_group *bfqg)
 {
-	struct bfq_queue *async_bfqq = bic_to_bfqq(bic, 0);
-	struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, 1);
-	struct bfq_group *bfqg;
+	struct bfq_queue *async_bfqq = bic_to_bfqq(bic, false);
+	struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, true);
 	struct bfq_entity *entity;
 
-	bfqg = bfq_find_set_group(bfqd, blkcg);
-
-	if (unlikely(!bfqg))
-		bfqg = bfqd->root_group;
-
 	if (async_bfqq) {
 		entity = &async_bfqq->entity;
 
 		if (entity->sched_data != &bfqg->sched_data) {
-			bic_set_bfqq(bic, NULL, 0);
+			bic_set_bfqq(bic, NULL, false);
 			bfq_release_process_ref(bfqd, async_bfqq);
 		}
 	}
 
 	if (sync_bfqq) {
-		entity = &sync_bfqq->entity;
-		if (entity->sched_data != &bfqg->sched_data)
-			bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
+		if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
+			/* We are the only user of this bfqq, just move it */
+			if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
+				bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
+		} else {
+			struct bfq_queue *bfqq;
+
+			/*
+			 * The queue was merged to a different queue. Check
+			 * that the merge chain still belongs to the same
+			 * cgroup.
+			 */
+			for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
+				if (bfqq->entity.sched_data !=
+				    &bfqg->sched_data)
+					break;
+			if (bfqq) {
+				/*
+				 * Some queue changed cgroup so the merge is
+				 * not valid anymore. We cannot easily just
+				 * cancel the merge (by clearing new_bfqq) as
+				 * there may be other processes using this
+				 * queue and holding refs to all queues below
+				 * sync_bfqq->new_bfqq. Similarly if the merge
+				 * already happened, we need to detach from
+				 * bfqq now so that we cannot merge bio to a
+				 * request from the old cgroup.
+				 */
+				bfq_put_cooperator(sync_bfqq);
+				bic_set_bfqq(bic, NULL, true);
+				bfq_release_process_ref(bfqd, sync_bfqq);
+			}
+		}
 	}
 
 	return bfqg;
@@ -738,20 +768,24 @@
 void bfq_bic_update_cgroup(struct bfq_io_cq *bic, struct bio *bio)
 {
 	struct bfq_data *bfqd = bic_to_bfqd(bic);
-	struct bfq_group *bfqg = NULL;
+	struct bfq_group *bfqg = bfq_bio_bfqg(bfqd, bio);
 	uint64_t serial_nr;
 
-	rcu_read_lock();
-	serial_nr = __bio_blkcg(bio)->css.serial_nr;
+	serial_nr = bfqg_to_blkg(bfqg)->blkcg->css.serial_nr;
 
 	/*
 	 * Check whether blkcg has changed.  The condition may trigger
 	 * spuriously on a newly created cic but there's no harm.
 	 */
 	if (unlikely(!bfqd) || likely(bic->blkcg_serial_nr == serial_nr))
-		goto out;
+		return;
 
-	bfqg = __bfq_bic_change_cgroup(bfqd, bic, __bio_blkcg(bio));
+	/*
+	 * New cgroup for this process. Make sure it is linked to bfq internal
+	 * cgroup hierarchy.
+	 */
+	bfq_link_bfqg(bfqd, bfqg);
+	__bfq_bic_change_cgroup(bfqd, bic, bfqg);
 	/*
 	 * Update blkg_path for bfq_log_* functions. We cache this
 	 * path, and update it here, for the following
@@ -804,8 +838,6 @@
 	 */
 	blkg_path(bfqg_to_blkg(bfqg), bfqg->blkg_path, sizeof(bfqg->blkg_path));
 	bic->blkcg_serial_nr = serial_nr;
-out:
-	rcu_read_unlock();
 }
 
 /**
@@ -933,6 +965,7 @@
 
 put_async_queues:
 	bfq_put_async_queues(bfqd, bfqg);
+	bfqg->online = false;
 
 	spin_unlock_irqrestore(&bfqd->lock, flags);
 	/*
@@ -1422,7 +1455,7 @@
 	bfq_end_wr_async_queues(bfqd, bfqd->root_group);
 }
 
-struct bfq_group *bfq_find_set_group(struct bfq_data *bfqd, struct blkcg *blkcg)
+struct bfq_group *bfq_bio_bfqg(struct bfq_data *bfqd, struct bio *bio)
 {
 	return bfqd->root_group;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/block/bfq-iosched.c
+++ linux-xilinx-zynqmp-5.15.0/block/bfq-iosched.c
@@ -386,6 +386,12 @@
 
 void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
 {
+	struct bfq_queue *old_bfqq = bic->bfqq[is_sync];
+
+	/* Clear bic pointer if bfqq is detached from this bic */
+	if (old_bfqq && old_bfqq->bic == bic)
+		old_bfqq->bic = NULL;
+
 	/*
 	 * If bfqq != NULL, then a non-stable queue merge between
 	 * bic->bfqq and bfqq is happening here. This causes troubles
@@ -461,6 +467,8 @@
  */
 void bfq_schedule_dispatch(struct bfq_data *bfqd)
 {
+	lockdep_assert_held(&bfqd->lock);
+
 	if (bfqd->queued != 0) {
 		bfq_log(bfqd, "schedule dispatch");
 		blk_mq_run_hw_queues(bfqd->queue, true);
@@ -2022,9 +2030,7 @@
 	if (!bfqd->last_completed_rq_bfqq ||
 	    bfqd->last_completed_rq_bfqq == bfqq ||
 	    bfq_bfqq_has_short_ttime(bfqq) ||
-	    bfqq->dispatched > 0 ||
-	    now_ns - bfqd->last_completion >= 4 * NSEC_PER_MSEC ||
-	    bfqd->last_completed_rq_bfqq == bfqq->waker_bfqq)
+	    now_ns - bfqd->last_completion >= 4 * NSEC_PER_MSEC)
 		return;
 
 	if (bfqd->last_completed_rq_bfqq !=
@@ -2084,7 +2090,7 @@
 	bfqq->queued[rq_is_sync(rq)]++;
 	bfqd->queued++;
 
-	if (RB_EMPTY_ROOT(&bfqq->sort_list) && bfq_bfqq_sync(bfqq)) {
+	if (bfq_bfqq_sync(bfqq) && RQ_BIC(rq)->requests <= 1) {
 		bfq_check_waker(bfqd, bfqq, now_ns);
 
 		/*
@@ -2337,10 +2343,17 @@
 
 	spin_lock_irq(&bfqd->lock);
 
-	if (bic)
+	if (bic) {
+		/*
+		 * Make sure cgroup info is uptodate for current process before
+		 * considering the merge.
+		 */
+		bfq_bic_update_cgroup(bic, bio);
+
 		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf));
-	else
+	} else {
 		bfqd->bio_bfqq = NULL;
+	}
 	bfqd->bio_bic = bic;
 
 	ret = blk_mq_sched_try_merge(q, bio, nr_segs, &free);
@@ -2370,8 +2383,6 @@
 	return ELEVATOR_NO_MERGE;
 }
 
-static struct bfq_queue *bfq_init_rq(struct request *rq);
-
 static void bfq_request_merged(struct request_queue *q, struct request *req,
 			       enum elv_merge type)
 {
@@ -2380,7 +2391,7 @@
 	    blk_rq_pos(req) <
 	    blk_rq_pos(container_of(rb_prev(&req->rb_node),
 				    struct request, rb_node))) {
-		struct bfq_queue *bfqq = bfq_init_rq(req);
+		struct bfq_queue *bfqq = RQ_BFQQ(req);
 		struct bfq_data *bfqd;
 		struct request *prev, *next_rq;
 
@@ -2432,8 +2443,8 @@
 static void bfq_requests_merged(struct request_queue *q, struct request *rq,
 				struct request *next)
 {
-	struct bfq_queue *bfqq = bfq_init_rq(rq),
-		*next_bfqq = bfq_init_rq(next);
+	struct bfq_queue *bfqq = RQ_BFQQ(rq),
+		*next_bfqq = RQ_BFQQ(next);
 
 	if (!bfqq)
 		goto remove;
@@ -2638,6 +2649,14 @@
 	if (process_refs == 0 || new_process_refs == 0)
 		return NULL;
 
+	/*
+	 * Make sure merged queues belong to the same parent. Parents could
+	 * have changed since the time we decided the two queues are suitable
+	 * for merging.
+	 */
+	if (new_bfqq->entity.parent != bfqq->entity.parent)
+		return NULL;
+
 	bfq_log_bfqq(bfqq->bfqd, bfqq, "scheduling merge with queue %d",
 		new_bfqq->pid);
 
@@ -2662,6 +2681,15 @@
 	 * are likely to increase the throughput.
 	 */
 	bfqq->new_bfqq = new_bfqq;
+	/*
+	 * The above assignment schedules the following redirections:
+	 * each time some I/O for bfqq arrives, the process that
+	 * generated that I/O is disassociated from bfqq and
+	 * associated with new_bfqq. Here we increases new_bfqq->ref
+	 * in advance, adding the number of processes that are
+	 * expected to be associated with new_bfqq as they happen to
+	 * issue I/O.
+	 */
 	new_bfqq->ref += process_refs;
 	return new_bfqq;
 }
@@ -2724,6 +2752,14 @@
 {
 	struct bfq_queue *in_service_bfqq, *new_bfqq;
 
+	/* if a merge has already been setup, then proceed with that first */
+	new_bfqq = bfqq->new_bfqq;
+	if (new_bfqq) {
+		while (new_bfqq->new_bfqq)
+			new_bfqq = new_bfqq->new_bfqq;
+		return new_bfqq;
+	}
+
 	/*
 	 * Check delayed stable merge for rotational or non-queueing
 	 * devs. For this branch to be executed, bfqq must not be
@@ -2762,9 +2798,12 @@
 				struct bfq_queue *new_bfqq =
 					bfq_setup_merge(bfqq, stable_merge_bfqq);
 
-				bic->stably_merged = true;
-				if (new_bfqq && new_bfqq->bic)
-					new_bfqq->bic->stably_merged = true;
+				if (new_bfqq) {
+					bic->stably_merged = true;
+					if (new_bfqq->bic)
+						new_bfqq->bic->stably_merged =
+									true;
+				}
 				return new_bfqq;
 			} else
 				return NULL;
@@ -2825,9 +2864,6 @@
 	if (bfq_too_late_for_merging(bfqq))
 		return NULL;
 
-	if (bfqq->new_bfqq)
-		return bfqq->new_bfqq;
-
 	if (!io_struct || unlikely(bfqq == &bfqd->oom_bfqq))
 		return NULL;
 
@@ -2945,10 +2981,12 @@
 	bfq_put_queue(bfqq);
 }
 
-static void
-bfq_merge_bfqqs(struct bfq_data *bfqd, struct bfq_io_cq *bic,
-		struct bfq_queue *bfqq, struct bfq_queue *new_bfqq)
+static struct bfq_queue *bfq_merge_bfqqs(struct bfq_data *bfqd,
+					 struct bfq_io_cq *bic,
+					 struct bfq_queue *bfqq)
 {
+	struct bfq_queue *new_bfqq = bfqq->new_bfqq;
+
 	bfq_log_bfqq(bfqd, bfqq, "merging with queue %lu",
 		(unsigned long)new_bfqq->pid);
 	/* Save weight raising and idle window of the merged queues */
@@ -3014,7 +3052,7 @@
 	/*
 	 * Merge queues (that is, let bic redirect its requests to new_bfqq)
 	 */
-	bic_set_bfqq(bic, new_bfqq, 1);
+	bic_set_bfqq(bic, new_bfqq, true);
 	bfq_mark_bfqq_coop(new_bfqq);
 	/*
 	 * new_bfqq now belongs to at least two bics (it is a shared queue):
@@ -3042,6 +3080,8 @@
 	bfq_reassign_last_bfqq(bfqq, new_bfqq);
 
 	bfq_release_process_ref(bfqd, bfqq);
+
+	return new_bfqq;
 }
 
 static bool bfq_allow_bio_merge(struct request_queue *q, struct request *rq,
@@ -3077,14 +3117,8 @@
 		 * fulfilled, i.e., bic can be redirected to new_bfqq
 		 * and bfqq can be put.
 		 */
-		bfq_merge_bfqqs(bfqd, bfqd->bio_bic, bfqq,
-				new_bfqq);
-		/*
-		 * If we get here, bio will be queued into new_queue,
-		 * so use new_bfqq to decide whether bio and rq can be
-		 * merged.
-		 */
-		bfqq = new_bfqq;
+		while (bfqq != new_bfqq)
+			bfqq = bfq_merge_bfqqs(bfqd, bfqd->bio_bic, bfqq);
 
 		/*
 		 * Change also bqfd->bio_bfqq, as
@@ -5061,7 +5095,7 @@
 	struct bfq_data *bfqd = hctx->queue->elevator->elevator_data;
 	struct request *rq;
 	struct bfq_queue *in_serv_queue;
-	bool waiting_rq, idle_timer_disabled;
+	bool waiting_rq, idle_timer_disabled = false;
 
 	spin_lock_irq(&bfqd->lock);
 
@@ -5069,14 +5103,15 @@
 	waiting_rq = in_serv_queue && bfq_bfqq_wait_request(in_serv_queue);
 
 	rq = __bfq_dispatch_request(hctx);
-
-	idle_timer_disabled =
-		waiting_rq && !bfq_bfqq_wait_request(in_serv_queue);
+	if (in_serv_queue == bfqd->in_service_queue) {
+		idle_timer_disabled =
+			waiting_rq && !bfq_bfqq_wait_request(in_serv_queue);
+	}
 
 	spin_unlock_irq(&bfqd->lock);
-
-	bfq_update_dispatch_stats(hctx->queue, rq, in_serv_queue,
-				  idle_timer_disabled);
+	bfq_update_dispatch_stats(hctx->queue, rq,
+			idle_timer_disabled ? in_serv_queue : NULL,
+				idle_timer_disabled);
 
 	return rq;
 }
@@ -5173,7 +5208,7 @@
 	bfq_put_queue(bfqq);
 }
 
-static void bfq_put_cooperator(struct bfq_queue *bfqq)
+void bfq_put_cooperator(struct bfq_queue *bfqq)
 {
 	struct bfq_queue *__bfqq, *next;
 
@@ -5218,9 +5253,8 @@
 		unsigned long flags;
 
 		spin_lock_irqsave(&bfqd->lock, flags);
-		bfqq->bic = NULL;
-		bfq_exit_bfqq(bfqd, bfqq);
 		bic_set_bfqq(bic, NULL, is_sync);
+		bfq_exit_bfqq(bfqd, bfqq);
 		spin_unlock_irqrestore(&bfqd->lock, flags);
 	}
 }
@@ -5327,9 +5361,11 @@
 
 	bfqq = bic_to_bfqq(bic, false);
 	if (bfqq) {
-		bfq_release_process_ref(bfqd, bfqq);
-		bfqq = bfq_get_queue(bfqd, bio, BLK_RW_ASYNC, bic, true);
+		struct bfq_queue *old_bfqq = bfqq;
+
+		bfqq = bfq_get_queue(bfqd, bio, false, bic, true);
 		bic_set_bfqq(bic, bfqq, false);
+		bfq_release_process_ref(bfqd, old_bfqq);
 	}
 
 	bfqq = bic_to_bfqq(bic, true);
@@ -5444,9 +5480,7 @@
 	 * state before killing it.
 	 */
 	bfqq->bic = bic;
-	bfq_merge_bfqqs(bfqd, bic, bfqq, new_bfqq);
-
-	return new_bfqq;
+	return bfq_merge_bfqqs(bfqd, bic, bfqq);
 }
 
 /*
@@ -5579,14 +5613,7 @@
 	struct bfq_queue *bfqq;
 	struct bfq_group *bfqg;
 
-	rcu_read_lock();
-
-	bfqg = bfq_find_set_group(bfqd, __bio_blkcg(bio));
-	if (!bfqg) {
-		bfqq = &bfqd->oom_bfqq;
-		goto out;
-	}
-
+	bfqg = bfq_bio_bfqg(bfqd, bio);
 	if (!is_sync) {
 		async_bfqq = bfq_async_queue_prio(bfqd, bfqg, ioprio_class,
 						  ioprio);
@@ -5632,8 +5659,6 @@
 
 	if (bfqq != &bfqd->oom_bfqq && is_sync && !respawn)
 		bfqq = bfq_do_or_sched_stable_merge(bfqd, bfqq, bic);
-
-	rcu_read_unlock();
 	return bfqq;
 }
 
@@ -5887,6 +5912,7 @@
 	bool waiting, idle_timer_disabled = false;
 
 	if (new_bfqq) {
+		struct bfq_queue *old_bfqq = bfqq;
 		/*
 		 * Release the request's reference to the old bfqq
 		 * and make sure one is taken to the shared queue.
@@ -5902,18 +5928,18 @@
 		 * then complete the merge and redirect it to
 		 * new_bfqq.
 		 */
-		if (bic_to_bfqq(RQ_BIC(rq), 1) == bfqq)
-			bfq_merge_bfqqs(bfqd, RQ_BIC(rq),
-					bfqq, new_bfqq);
+		if (bic_to_bfqq(RQ_BIC(rq), 1) == bfqq) {
+			while (bfqq != new_bfqq)
+				bfqq = bfq_merge_bfqqs(bfqd, RQ_BIC(rq), bfqq);
+		}
 
-		bfq_clear_bfqq_just_created(bfqq);
+		bfq_clear_bfqq_just_created(old_bfqq);
 		/*
 		 * rq is about to be enqueued into new_bfqq,
 		 * release rq reference on bfqq
 		 */
-		bfq_put_queue(bfqq);
+		bfq_put_queue(old_bfqq);
 		rq->elv.priv[1] = new_bfqq;
-		bfqq = new_bfqq;
 	}
 
 	bfq_update_io_thinktime(bfqd, bfqq);
@@ -5964,6 +5990,8 @@
 					   unsigned int cmd_flags) {}
 #endif /* CONFIG_BFQ_CGROUP_DEBUG */
 
+static struct bfq_queue *bfq_init_rq(struct request *rq);
+
 static void bfq_insert_request(struct blk_mq_hw_ctx *hctx, struct request *rq,
 			       bool at_head)
 {
@@ -5979,60 +6007,16 @@
 		bfqg_stats_update_legacy_io(q, rq);
 #endif
 	spin_lock_irq(&bfqd->lock);
+	bfqq = bfq_init_rq(rq);
 	if (blk_mq_sched_try_insert_merge(q, rq, &free)) {
 		spin_unlock_irq(&bfqd->lock);
 		blk_mq_free_requests(&free);
 		return;
 	}
 
-	spin_unlock_irq(&bfqd->lock);
-
 	trace_block_rq_insert(rq);
 
-	spin_lock_irq(&bfqd->lock);
-	bfqq = bfq_init_rq(rq);
-
-	/*
-	 * Reqs with at_head or passthrough flags set are to be put
-	 * directly into dispatch list. Additional case for putting rq
-	 * directly into the dispatch queue: the only active
-	 * bfq_queues are bfqq and either its waker bfq_queue or one
-	 * of its woken bfq_queues. The rationale behind this
-	 * additional condition is as follows:
-	 * - consider a bfq_queue, say Q1, detected as a waker of
-	 *   another bfq_queue, say Q2
-	 * - by definition of a waker, Q1 blocks the I/O of Q2, i.e.,
-	 *   some I/O of Q1 needs to be completed for new I/O of Q2
-	 *   to arrive.  A notable example of waker is journald
-	 * - so, Q1 and Q2 are in any respect the queues of two
-	 *   cooperating processes (or of two cooperating sets of
-	 *   processes): the goal of Q1's I/O is doing what needs to
-	 *   be done so that new Q2's I/O can finally be
-	 *   issued. Therefore, if the service of Q1's I/O is delayed,
-	 *   then Q2's I/O is delayed too.  Conversely, if Q2's I/O is
-	 *   delayed, the goal of Q1's I/O is hindered.
-	 * - as a consequence, if some I/O of Q1/Q2 arrives while
-	 *   Q2/Q1 is the only queue in service, there is absolutely
-	 *   no point in delaying the service of such an I/O. The
-	 *   only possible result is a throughput loss
-	 * - so, when the above condition holds, the best option is to
-	 *   have the new I/O dispatched as soon as possible
-	 * - the most effective and efficient way to attain the above
-	 *   goal is to put the new I/O directly in the dispatch
-	 *   list
-	 * - as an additional restriction, Q1 and Q2 must be the only
-	 *   busy queues for this commit to put the I/O of Q2/Q1 in
-	 *   the dispatch list.  This is necessary, because, if also
-	 *   other queues are waiting for service, then putting new
-	 *   I/O directly in the dispatch list may evidently cause a
-	 *   violation of service guarantees for the other queues
-	 */
-	if (!bfqq ||
-	    (bfqq != bfqd->in_service_queue &&
-	     bfqd->in_service_queue != NULL &&
-	     bfq_tot_busy_queues(bfqd) == 1 + bfq_bfqq_busy(bfqq) &&
-	     (bfqq->waker_bfqq == bfqd->in_service_queue ||
-	      bfqd->in_service_queue->waker_bfqq == bfqq)) || at_head) {
+	if (!bfqq || at_head) {
 		if (at_head)
 			list_add(&rq->queuelist, &bfqd->dispatch);
 		else
@@ -6059,7 +6043,6 @@
 	 * merge).
 	 */
 	cmd_flags = rq->cmd_flags;
-
 	spin_unlock_irq(&bfqd->lock);
 
 	bfq_update_insert_stats(q, bfqq, idle_timer_disabled,
@@ -6453,6 +6436,7 @@
 		bfq_completed_request(bfqq, bfqd);
 	}
 	bfq_finish_requeue_request_body(bfqq);
+	RQ_BIC(rq)->requests--;
 	spin_unlock_irqrestore(&bfqd->lock, flags);
 
 	/*
@@ -6487,14 +6471,14 @@
 {
 	bfq_log_bfqq(bfqq->bfqd, bfqq, "splitting queue");
 
-	if (bfqq_process_refs(bfqq) == 1) {
+	if (bfqq_process_refs(bfqq) == 1 && !bfqq->new_bfqq) {
 		bfqq->pid = current->pid;
 		bfq_clear_bfqq_coop(bfqq);
 		bfq_clear_bfqq_split_coop(bfqq);
 		return bfqq;
 	}
 
-	bic_set_bfqq(bic, NULL, 1);
+	bic_set_bfqq(bic, NULL, true);
 
 	bfq_put_cooperator(bfqq);
 
@@ -6581,6 +6565,39 @@
 	rq->elv.priv[0] = rq->elv.priv[1] = NULL;
 }
 
+static struct bfq_queue *bfq_waker_bfqq(struct bfq_queue *bfqq)
+{
+	struct bfq_queue *new_bfqq = bfqq->new_bfqq;
+	struct bfq_queue *waker_bfqq = bfqq->waker_bfqq;
+
+	if (!waker_bfqq)
+		return NULL;
+
+	while (new_bfqq) {
+		if (new_bfqq == waker_bfqq) {
+			/*
+			 * If waker_bfqq is in the merge chain, and current
+			 * is the only process, waker_bfqq can be freed.
+			 */
+			if (bfqq_process_refs(waker_bfqq) == 1)
+				return NULL;
+
+			return waker_bfqq;
+		}
+
+		new_bfqq = new_bfqq->new_bfqq;
+	}
+
+	/*
+	 * If waker_bfqq is not in the merge chain, and it's procress reference
+	 * is 0, waker_bfqq can be freed.
+	 */
+	if (bfqq_process_refs(waker_bfqq) == 0)
+		return NULL;
+
+	return waker_bfqq;
+}
+
 /*
  * If needed, init rq, allocate bfq data structures associated with
  * rq, and increment reference counters in the destination bfq_queue
@@ -6641,7 +6658,7 @@
 		/* If the queue was seeky for too long, break it apart. */
 		if (bfq_bfqq_coop(bfqq) && bfq_bfqq_split_coop(bfqq) &&
 			!bic->stably_merged) {
-			struct bfq_queue *old_bfqq = bfqq;
+			struct bfq_queue *waker_bfqq = bfq_waker_bfqq(bfqq);
 
 			/* Update bic before losing reference to bfqq */
 			if (bfq_bfqq_in_large_burst(bfqq))
@@ -6654,7 +6671,13 @@
 				bfqq = bfq_get_bfqq_handle_split(bfqd, bic, bio,
 								 true, is_sync,
 								 NULL);
-				bfqq->waker_bfqq = old_bfqq->waker_bfqq;
+				if (unlikely(bfqq == &bfqd->oom_bfqq))
+					bfqq_already_existing = true;
+			} else
+				bfqq_already_existing = true;
+
+			if (!bfqq_already_existing) {
+				bfqq->waker_bfqq = waker_bfqq;
 				bfqq->tentative_waker_bfqq = NULL;
 
 				/*
@@ -6664,16 +6687,16 @@
 				 * woken_list of the waker. See
 				 * bfq_check_waker for details.
 				 */
-				if (bfqq->waker_bfqq)
+				if (waker_bfqq)
 					hlist_add_head(&bfqq->woken_list_node,
 						       &bfqq->waker_bfqq->woken_list);
-			} else
-				bfqq_already_existing = true;
+			}
 		}
 	}
 
 	bfqq->allocated++;
 	bfqq->ref++;
+	bic->requests++;
 	bfq_log_bfqq(bfqd, bfqq, "get_request %p: bfqq %p, %d",
 		     rq, bfqq, bfqq->ref);
 
@@ -6686,7 +6709,8 @@
 	 * addition, if the queue has also just been split, we have to
 	 * resume its state.
 	 */
-	if (likely(bfqq != &bfqd->oom_bfqq) && bfqq_process_refs(bfqq) == 1) {
+	if (likely(bfqq != &bfqd->oom_bfqq) && !bfqq->new_bfqq &&
+	    bfqq_process_refs(bfqq) == 1) {
 		bfqq->bic = bic;
 		if (split) {
 			/*
@@ -6770,8 +6794,8 @@
 	bfq_bfqq_expire(bfqd, bfqq, true, reason);
 
 schedule_dispatch:
-	spin_unlock_irqrestore(&bfqd->lock, flags);
 	bfq_schedule_dispatch(bfqd);
+	spin_unlock_irqrestore(&bfqd->lock, flags);
 }
 
 /*
@@ -6920,6 +6944,8 @@
 	spin_unlock_irq(&bfqd->lock);
 #endif
 
+	wbt_enable_default(bfqd->queue);
+
 	kfree(bfqd);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/bfq-iosched.h
+++ linux-xilinx-zynqmp-5.15.0/block/bfq-iosched.h
@@ -466,6 +466,7 @@
 	struct bfq_queue *stable_merge_bfqq;
 
 	bool stably_merged;	/* non splittable if true */
+	unsigned int requests;	/* Number of requests this process has in flight */
 };
 
 /**
@@ -925,6 +926,8 @@
 
 	/* reference counter (see comments in bfq_bic_update_cgroup) */
 	int ref;
+	/* Is bfq_group still online? */
+	bool online;
 
 	struct bfq_entity entity;
 	struct bfq_sched_data sched_data;
@@ -976,6 +979,7 @@
 void bfq_bfqq_expire(struct bfq_data *bfqd, struct bfq_queue *bfqq,
 		     bool compensate, enum bfqq_expiration reason);
 void bfq_put_queue(struct bfq_queue *bfqq);
+void bfq_put_cooperator(struct bfq_queue *bfqq);
 void bfq_end_wr_async_queues(struct bfq_data *bfqd, struct bfq_group *bfqg);
 void bfq_release_process_ref(struct bfq_data *bfqd, struct bfq_queue *bfqq);
 void bfq_schedule_dispatch(struct bfq_data *bfqd);
@@ -1003,8 +1007,7 @@
 void bfq_init_entity(struct bfq_entity *entity, struct bfq_group *bfqg);
 void bfq_bic_update_cgroup(struct bfq_io_cq *bic, struct bio *bio);
 void bfq_end_wr_async(struct bfq_data *bfqd);
-struct bfq_group *bfq_find_set_group(struct bfq_data *bfqd,
-				     struct blkcg *blkcg);
+struct bfq_group *bfq_bio_bfqg(struct bfq_data *bfqd, struct bio *bio);
 struct blkcg_gq *bfqg_to_blkg(struct bfq_group *bfqg);
 struct bfq_group *bfqq_group(struct bfq_queue *bfqq);
 struct bfq_group *bfq_create_group_hierarchy(struct bfq_data *bfqd, int node);
--- linux-xilinx-zynqmp-5.15.0.orig/block/bfq-wf2q.c
+++ linux-xilinx-zynqmp-5.15.0/block/bfq-wf2q.c
@@ -519,7 +519,7 @@
 static unsigned short bfq_weight_to_ioprio(int weight)
 {
 	return max_t(int, 0,
-		     IOPRIO_NR_LEVELS * BFQ_WEIGHT_CONVERSION_COEFF - weight);
+		     IOPRIO_NR_LEVELS - weight / BFQ_WEIGHT_CONVERSION_COEFF);
 }
 
 static void bfq_get_entity(struct bfq_entity *entity)
--- linux-xilinx-zynqmp-5.15.0.orig/block/bio-integrity.c
+++ linux-xilinx-zynqmp-5.15.0/block/bio-integrity.c
@@ -203,8 +203,7 @@
 	unsigned long start, end;
 	unsigned int len, nr_pages;
 	unsigned int bytes, offset, i;
-	unsigned int intervals;
-	blk_status_t status;
+	gfp_t gfp = GFP_NOIO;
 
 	if (!bi)
 		return true;
@@ -227,13 +226,19 @@
 		if (!bi->profile->generate_fn ||
 		    !(bi->flags & BLK_INTEGRITY_GENERATE))
 			return true;
+
+		/*
+		 * Zero the memory allocated to not leak uninitialized kernel
+		 * memory to disk.  For PI this only affects the app tag, but
+		 * for non-integrity metadata it affects the entire metadata
+		 * buffer.
+		 */
+		gfp |= __GFP_ZERO;
 	}
-	intervals = bio_integrity_intervals(bi, bio_sectors(bio));
 
 	/* Allocate kernel buffer for protection data */
-	len = intervals * bi->tuple_size;
-	buf = kmalloc(len, GFP_NOIO);
-	status = BLK_STS_RESOURCE;
+	len = bio_integrity_bytes(bi, bio_sectors(bio));
+	buf = kmalloc(len, gfp);
 	if (unlikely(buf == NULL)) {
 		printk(KERN_ERR "could not allocate integrity buffer\n");
 		goto err_end_io;
@@ -248,7 +253,6 @@
 	if (IS_ERR(bip)) {
 		printk(KERN_ERR "could not allocate data integrity bioset\n");
 		kfree(buf);
-		status = BLK_STS_RESOURCE;
 		goto err_end_io;
 	}
 
@@ -276,7 +280,6 @@
 
 		if (ret == 0) {
 			printk(KERN_ERR "could not attach integrity payload\n");
-			status = BLK_STS_RESOURCE;
 			goto err_end_io;
 		}
 
@@ -298,7 +301,7 @@
 	return true;
 
 err_end_io:
-	bio->bi_status = status;
+	bio->bi_status = BLK_STS_RESOURCE;
 	bio_endio(bio);
 	return false;
 
@@ -373,7 +376,7 @@
 	struct blk_integrity *bi = blk_get_integrity(bio->bi_bdev->bd_disk);
 	unsigned bytes = bio_integrity_bytes(bi, bytes_done >> 9);
 
-	bip->bip_iter.bi_sector += bytes_done >> 9;
+	bip->bip_iter.bi_sector += bio_integrity_intervals(bi, bytes_done >> 9);
 	bvec_iter_advance(bip->bip_vec, &bip->bip_iter, bytes);
 }
 
@@ -417,6 +420,7 @@
 
 	bip->bip_vcnt = bip_src->bip_vcnt;
 	bip->bip_iter = bip_src->bip_iter;
+	bip->bip_flags = bip_src->bip_flags & ~BIP_BLOCK_INTEGRITY;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/block/bio.c
+++ linux-xilinx-zynqmp-5.15.0/block/bio.c
@@ -73,7 +73,7 @@
 	struct kmem_cache *slab;
 	unsigned int slab_ref;
 	unsigned int slab_size;
-	char name[8];
+	char name[12];
 };
 static DEFINE_MUTEX(bio_slab_lock);
 static DEFINE_XARRAY(bio_slabs);
@@ -567,7 +567,8 @@
 				offset = new_size - done;
 			else
 				offset = 0;
-			zero_user(bv.bv_page, offset, bv.bv_len - offset);
+			zero_user(bv.bv_page, bv.bv_offset + offset,
+				  bv.bv_len - offset);
 			truncated = true;
 		}
 		done += bv.bv_len;
@@ -664,6 +665,7 @@
 		bio_alloc_cache_prune(cache, -1U);
 	}
 	free_percpu(bs->cache);
+	bs->cache = NULL;
 }
 
 /**
@@ -807,7 +809,7 @@
 
 	if ((addr1 | mask) != (addr2 | mask))
 		return false;
-	if (bv->bv_len + len > queue_max_segment_size(q))
+	if (len > queue_max_segment_size(q) - bv->bv_len)
 		return false;
 	return __bio_try_merge_page(bio, page, len, offset, same_page);
 }
@@ -908,7 +910,7 @@
 int bio_add_zone_append_page(struct bio *bio, struct page *page,
 			     unsigned int len, unsigned int offset)
 {
-	struct request_queue *q = bio->bi_bdev->bd_disk->queue;
+	struct request_queue *q = bdev_get_queue(bio->bi_bdev);
 	bool same_page = false;
 
 	if (WARN_ON_ONCE(bio_op(bio) != REQ_OP_ZONE_APPEND))
@@ -1024,7 +1026,7 @@
 		return;
 
 	bio_for_each_segment_all(bvec, bio, iter_all) {
-		if (mark_dirty && !PageCompound(bvec->bv_page))
+		if (mark_dirty)
 			set_page_dirty_lock(bvec->bv_page);
 		put_page(bvec->bv_page);
 	}
@@ -1052,7 +1054,7 @@
 
 static int bio_iov_bvec_set_append(struct bio *bio, struct iov_iter *iter)
 {
-	struct request_queue *q = bio->bi_bdev->bd_disk->queue;
+	struct request_queue *q = bdev_get_queue(bio->bi_bdev);
 	struct iov_iter i = *iter;
 
 	iov_iter_truncate(&i, queue_max_zone_append_sectors(q) << 9);
@@ -1069,6 +1071,37 @@
 		put_page(pages[i]);
 }
 
+static int bio_iov_add_page(struct bio *bio, struct page *page,
+		unsigned int len, unsigned int offset)
+{
+	bool same_page = false;
+
+	if (!__bio_try_merge_page(bio, page, len, offset, &same_page)) {
+		if (WARN_ON_ONCE(bio_full(bio, len)))
+			return -EINVAL;
+		__bio_add_page(bio, page, len, offset);
+		return 0;
+	}
+
+	if (same_page)
+		put_page(page);
+	return 0;
+}
+
+static int bio_iov_add_zone_append_page(struct bio *bio, struct page *page,
+		unsigned int len, unsigned int offset)
+{
+	struct request_queue *q = bdev_get_queue(bio->bi_bdev);
+	bool same_page = false;
+
+	if (bio_add_hw_page(q, bio, page, len, offset,
+			queue_max_zone_append_sectors(q), &same_page) != len)
+		return -EINVAL;
+	if (same_page)
+		put_page(page);
+	return 0;
+}
+
 #define PAGE_PTRS_PER_BVEC     (sizeof(struct bio_vec) / sizeof(struct page *))
 
 /**
@@ -1087,61 +1120,11 @@
 	unsigned short entries_left = bio->bi_max_vecs - bio->bi_vcnt;
 	struct bio_vec *bv = bio->bi_io_vec + bio->bi_vcnt;
 	struct page **pages = (struct page **)bv;
-	bool same_page = false;
-	ssize_t size, left;
-	unsigned len, i;
-	size_t offset;
-
-	/*
-	 * Move page array up in the allocated memory for the bio vecs as far as
-	 * possible so that we can start filling biovecs from the beginning
-	 * without overwriting the temporary page array.
-	*/
-	BUILD_BUG_ON(PAGE_PTRS_PER_BVEC < 2);
-	pages += entries_left * (PAGE_PTRS_PER_BVEC - 1);
-
-	size = iov_iter_get_pages(iter, pages, LONG_MAX, nr_pages, &offset);
-	if (unlikely(size <= 0))
-		return size ? size : -EFAULT;
-
-	for (left = size, i = 0; left > 0; left -= len, i++) {
-		struct page *page = pages[i];
-
-		len = min_t(size_t, PAGE_SIZE - offset, left);
-
-		if (__bio_try_merge_page(bio, page, len, offset, &same_page)) {
-			if (same_page)
-				put_page(page);
-		} else {
-			if (WARN_ON_ONCE(bio_full(bio, len))) {
-				bio_put_pages(pages + i, left, offset);
-				return -EINVAL;
-			}
-			__bio_add_page(bio, page, len, offset);
-		}
-		offset = 0;
-	}
-
-	iov_iter_advance(iter, size);
-	return 0;
-}
-
-static int __bio_iov_append_get_pages(struct bio *bio, struct iov_iter *iter)
-{
-	unsigned short nr_pages = bio->bi_max_vecs - bio->bi_vcnt;
-	unsigned short entries_left = bio->bi_max_vecs - bio->bi_vcnt;
-	struct request_queue *q = bio->bi_bdev->bd_disk->queue;
-	unsigned int max_append_sectors = queue_max_zone_append_sectors(q);
-	struct bio_vec *bv = bio->bi_io_vec + bio->bi_vcnt;
-	struct page **pages = (struct page **)bv;
 	ssize_t size, left;
 	unsigned len, i;
 	size_t offset;
 	int ret = 0;
 
-	if (WARN_ON_ONCE(!max_append_sectors))
-		return 0;
-
 	/*
 	 * Move page array up in the allocated memory for the bio vecs as far as
 	 * possible so that we can start filling biovecs from the beginning
@@ -1156,17 +1139,18 @@
 
 	for (left = size, i = 0; left > 0; left -= len, i++) {
 		struct page *page = pages[i];
-		bool same_page = false;
 
 		len = min_t(size_t, PAGE_SIZE - offset, left);
-		if (bio_add_hw_page(q, bio, page, len, offset,
-				max_append_sectors, &same_page) != len) {
+		if (bio_op(bio) == REQ_OP_ZONE_APPEND)
+			ret = bio_iov_add_zone_append_page(bio, page, len,
+					offset);
+		else
+			ret = bio_iov_add_page(bio, page, len, offset);
+
+		if (ret) {
 			bio_put_pages(pages + i, left, offset);
-			ret = -EINVAL;
 			break;
 		}
-		if (same_page)
-			put_page(page);
 		offset = 0;
 	}
 
@@ -1208,10 +1192,7 @@
 	}
 
 	do {
-		if (bio_op(bio) == REQ_OP_ZONE_APPEND)
-			ret = __bio_iov_append_get_pages(bio, iter);
-		else
-			ret = __bio_iov_iter_get_pages(bio, iter);
+		ret = __bio_iov_iter_get_pages(bio, iter);
 	} while (!ret && iov_iter_count(iter) && !bio_full(bio, 0));
 
 	/* don't account direct I/O as memory stall */
@@ -1288,10 +1269,12 @@
 		struct bio_vec src_bv = bio_iter_iovec(src, *src_iter);
 		struct bio_vec dst_bv = bio_iter_iovec(dst, *dst_iter);
 		unsigned int bytes = min(src_bv.bv_len, dst_bv.bv_len);
-		void *src_buf;
+		void *src_buf = bvec_kmap_local(&src_bv);
+		void *dst_buf = bvec_kmap_local(&dst_bv);
+
+		memcpy(dst_buf, src_buf, bytes);
 
-		src_buf = bvec_kmap_local(&src_bv);
-		memcpy_to_bvec(&dst_bv, src_buf);
+		kunmap_local(dst_buf);
 		kunmap_local(src_buf);
 
 		bio_advance_iter_single(src, src_iter, bytes);
@@ -1362,8 +1345,7 @@
 	struct bvec_iter_all iter_all;
 
 	bio_for_each_segment_all(bvec, bio, iter_all) {
-		if (!PageCompound(bvec->bv_page))
-			set_page_dirty_lock(bvec->bv_page);
+		set_page_dirty_lock(bvec->bv_page);
 	}
 }
 
@@ -1411,7 +1393,7 @@
 	struct bvec_iter_all iter_all;
 
 	bio_for_each_segment_all(bvec, bio, iter_all) {
-		if (!PageDirty(bvec->bv_page) && !PageCompound(bvec->bv_page))
+		if (!PageDirty(bvec->bv_page))
 			goto defer;
 	}
 
@@ -1466,11 +1448,10 @@
 	if (!bio_integrity_endio(bio))
 		return;
 
-	if (bio->bi_bdev && bio_flagged(bio, BIO_TRACKED))
-		rq_qos_done_bio(bio->bi_bdev->bd_disk->queue, bio);
+	rq_qos_done_bio(bio);
 
 	if (bio->bi_bdev && bio_flagged(bio, BIO_TRACE_COMPLETION)) {
-		trace_block_bio_complete(bio->bi_bdev->bd_disk->queue, bio);
+		trace_block_bio_complete(bdev_get_queue(bio->bi_bdev), bio);
 		bio_clear_flag(bio, BIO_TRACE_COMPLETION);
 	}
 
@@ -1551,7 +1532,7 @@
 void bio_trim(struct bio *bio, sector_t offset, sector_t size)
 {
 	if (WARN_ON_ONCE(offset > BIO_MAX_SECTORS || size > BIO_MAX_SECTORS ||
-			 offset + size > bio->bi_iter.bi_size))
+			 offset + size > bio_sectors(bio)))
 		return;
 
 	size <<= 9;
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-cgroup.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-cgroup.c
@@ -425,6 +425,7 @@
 {
 	struct blkcg_gq *blkg, *n;
 	int count = BLKG_DESTROY_BATCH_SIZE;
+	int i;
 
 restart:
 	spin_lock_irq(&q->queue_lock);
@@ -447,6 +448,18 @@
 		}
 	}
 
+	/*
+	 * Mark policy deactivated since policy offline has been done, and
+	 * the free is scheduled, so future blkcg_deactivate_policy() can
+	 * be bypassed
+	 */
+	for (i = 0; i < BLKCG_MAX_POLS; i++) {
+		struct blkcg_policy *pol = blkcg_policy[i];
+
+		if (pol)
+			__clear_bit(pol->plid, q->blkcg_pols);
+	}
+
 	q->root_blkg = NULL;
 	spin_unlock_irq(&q->queue_lock);
 }
@@ -633,6 +646,14 @@
 
 	q = bdev->bd_disk->queue;
 
+	/*
+	 * blkcg_deactivate_policy() requires queue to be frozen, we can grab
+	 * q_usage_counter to prevent concurrent with blkcg_deactivate_policy().
+	 */
+	ret = blk_queue_enter(q, 0);
+	if (ret)
+		goto fail;
+
 	rcu_read_lock();
 	spin_lock_irq(&q->queue_lock);
 
@@ -667,13 +688,13 @@
 		new_blkg = blkg_alloc(pos, q, GFP_KERNEL);
 		if (unlikely(!new_blkg)) {
 			ret = -ENOMEM;
-			goto fail;
+			goto fail_exit_queue;
 		}
 
 		if (radix_tree_preload(GFP_KERNEL)) {
 			blkg_free(new_blkg);
 			ret = -ENOMEM;
-			goto fail;
+			goto fail_exit_queue;
 		}
 
 		rcu_read_lock();
@@ -702,6 +723,7 @@
 			goto success;
 	}
 success:
+	blk_queue_exit(q);
 	ctx->bdev = bdev;
 	ctx->blkg = blkg;
 	ctx->body = input;
@@ -712,6 +734,8 @@
 fail_unlock:
 	spin_unlock_irq(&q->queue_lock);
 	rcu_read_unlock();
+fail_exit_queue:
+	blk_queue_exit(q);
 fail:
 	blkdev_put_no_open(bdev);
 	/*
@@ -844,11 +868,11 @@
 			blk_queue_root_blkg(bdev->bd_disk->queue);
 		struct blkg_iostat tmp;
 		int cpu;
+		unsigned long flags;
 
 		memset(&tmp, 0, sizeof(tmp));
 		for_each_possible_cpu(cpu) {
 			struct disk_stats *cpu_dkstats;
-			unsigned long flags;
 
 			cpu_dkstats = per_cpu_ptr(bdev->bd_stats, cpu);
 			tmp.ios[BLKG_IOSTAT_READ] +=
@@ -864,12 +888,13 @@
 				cpu_dkstats->sectors[STAT_WRITE] << 9;
 			tmp.bytes[BLKG_IOSTAT_DISCARD] +=
 				cpu_dkstats->sectors[STAT_DISCARD] << 9;
-
-			flags = u64_stats_update_begin_irqsave(&blkg->iostat.sync);
-			blkg_iostat_set(&blkg->iostat.cur, &tmp);
-			u64_stats_update_end_irqrestore(&blkg->iostat.sync, flags);
 		}
+
+		flags = u64_stats_update_begin_irqsave(&blkg->iostat.sync);
+		blkg_iostat_set(&blkg->iostat.cur, &tmp);
+		u64_stats_update_end_irqrestore(&blkg->iostat.sync, flags);
 	}
+	class_dev_iter_exit(&iter);
 }
 
 static void blkcg_print_one_stat(struct blkcg_gq *blkg, struct seq_file *s)
@@ -1349,6 +1374,10 @@
 		list_for_each_entry_reverse(blkg, &q->blkg_list, q_node)
 			pol->pd_init_fn(blkg->pd[pol->plid]);
 
+	if (pol->pd_online_fn)
+		list_for_each_entry_reverse(blkg, &q->blkg_list, q_node)
+			pol->pd_online_fn(blkg->pd[pol->plid]);
+
 	__set_bit(pol->plid, q->blkcg_pols);
 	ret = 0;
 
@@ -1875,12 +1904,8 @@
  */
 void bio_clone_blkg_association(struct bio *dst, struct bio *src)
 {
-	if (src->bi_blkg) {
-		if (dst->bi_blkg)
-			blkg_put(dst->bi_blkg);
-		blkg_get(src->bi_blkg);
-		dst->bi_blkg = src->bi_blkg;
-	}
+	if (src->bi_blkg)
+		bio_associate_blkg_from_css(dst, &bio_blkcg(src)->css);
 }
 EXPORT_SYMBOL_GPL(bio_clone_blkg_association);
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-core.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-core.c
@@ -49,6 +49,7 @@
 #include "blk-mq.h"
 #include "blk-mq-sched.h"
 #include "blk-pm.h"
+#include "blk-rq-qos.h"
 
 struct dentry *blk_debugfs_root;
 
@@ -350,13 +351,6 @@
 	wake_up_all(&q->mq_freeze_wq);
 }
 
-void blk_set_queue_dying(struct request_queue *q)
-{
-	blk_queue_flag_set(QUEUE_FLAG_DYING, q);
-	blk_queue_start_drain(q);
-}
-EXPORT_SYMBOL_GPL(blk_set_queue_dying);
-
 /**
  * blk_cleanup_queue - shutdown a request queue
  * @q: request queue to shutdown
@@ -374,7 +368,8 @@
 	WARN_ON_ONCE(blk_queue_registered(q));
 
 	/* mark @q DYING, no new request or merges will be allowed afterwards */
-	blk_set_queue_dying(q);
+	blk_queue_flag_set(QUEUE_FLAG_DYING, q);
+	blk_queue_start_drain(q);
 
 	blk_queue_flag_set(QUEUE_FLAG_NOMERGES, q);
 	blk_queue_flag_set(QUEUE_FLAG_NOXMERGES, q);
@@ -386,11 +381,16 @@
 	 */
 	blk_freeze_queue(q);
 
+	/* cleanup rq qos structures for queue without disk */
+	rq_qos_exit(q);
+
 	blk_queue_flag_set(QUEUE_FLAG_DEAD, q);
 
 	blk_sync_queue(q);
-	if (queue_is_mq(q))
+	if (queue_is_mq(q)) {
+		blk_mq_cancel_work_sync(q);
 		blk_mq_exit_queue(q);
+	}
 
 	/*
 	 * In theory, request pool of sched_tags belongs to request queue.
@@ -405,8 +405,6 @@
 		blk_mq_sched_free_requests(q);
 	mutex_unlock(&q->sysfs_lock);
 
-	percpu_ref_exit(&q->q_usage_counter);
-
 	/* @q is and will stay empty, shutdown and put */
 	blk_put_queue(q);
 }
@@ -447,7 +445,7 @@
 
 	while (!blk_try_enter_queue(q, pm)) {
 		if (flags & BLK_MQ_REQ_NOWAIT)
-			return -EBUSY;
+			return -EAGAIN;
 
 		/*
 		 * read pair of barrier in blk_freeze_queue_start(), we need to
@@ -478,7 +476,7 @@
 			if (test_bit(GD_DEAD, &disk->state))
 				goto dead;
 			bio_wouldblock_error(bio);
-			return -EBUSY;
+			return -EAGAIN;
 		}
 
 		/*
@@ -695,22 +693,15 @@
 
 #endif /* CONFIG_FAIL_MAKE_REQUEST */
 
-static inline bool bio_check_ro(struct bio *bio)
+static inline void bio_check_ro(struct bio *bio)
 {
 	if (op_is_write(bio_op(bio)) && bdev_read_only(bio->bi_bdev)) {
-		char b[BDEVNAME_SIZE];
-
 		if (op_is_flush(bio->bi_opf) && !bio_sectors(bio))
-			return false;
-
-		WARN_ONCE(1,
-		       "Trying to write to read-only block-device %s (partno %d)\n",
-			bio_devname(bio, b), bio->bi_bdev->bd_partno);
+			return;
+		pr_warn_ratelimited("Trying to write to read-only block-device %pg\n",
+				    bio->bi_bdev);
 		/* Older lvm-tools actually trigger this */
-		return false;
 	}
-
-	return false;
 }
 
 static noinline int should_fail_bio(struct bio *bio)
@@ -816,8 +807,7 @@
 
 	if (should_fail_bio(bio))
 		goto end_io;
-	if (unlikely(bio_check_ro(bio)))
-		goto end_io;
+	bio_check_ro(bio);
 	if (!bio_flagged(bio, BIO_REMAPPED)) {
 		if (unlikely(bio_check_eod(bio)))
 			goto end_io;
@@ -887,10 +877,8 @@
 	if (unlikely(!current->io_context))
 		create_task_io_context(current, GFP_ATOMIC, q->node);
 
-	if (blk_throtl_bio(bio)) {
-		blkcg_bio_issue_init(bio);
+	if (blk_throtl_bio(bio))
 		return false;
-	}
 
 	blk_cgroup_bio_start(bio);
 	blkcg_bio_issue_init(bio);
@@ -1293,20 +1281,32 @@
 }
 
 static unsigned long __part_start_io_acct(struct block_device *part,
-					  unsigned int sectors, unsigned int op)
+					  unsigned int sectors, unsigned int op,
+					  unsigned long start_time)
 {
 	const int sgrp = op_stat_group(op);
-	unsigned long now = READ_ONCE(jiffies);
 
 	part_stat_lock();
-	update_io_ticks(part, now, false);
+	update_io_ticks(part, start_time, false);
 	part_stat_inc(part, ios[sgrp]);
 	part_stat_add(part, sectors[sgrp], sectors);
 	part_stat_local_inc(part, in_flight[op_is_write(op)]);
 	part_stat_unlock();
 
-	return now;
+	return start_time;
+}
+
+/**
+ * bio_start_io_acct_time - start I/O accounting for bio based drivers
+ * @bio:	bio to start account for
+ * @start_time:	start time that should be passed back to bio_end_io_acct().
+ */
+void bio_start_io_acct_time(struct bio *bio, unsigned long start_time)
+{
+	__part_start_io_acct(bio->bi_bdev, bio_sectors(bio),
+			     bio_op(bio), start_time);
 }
+EXPORT_SYMBOL_GPL(bio_start_io_acct_time);
 
 /**
  * bio_start_io_acct - start I/O accounting for bio based drivers
@@ -1316,14 +1316,15 @@
  */
 unsigned long bio_start_io_acct(struct bio *bio)
 {
-	return __part_start_io_acct(bio->bi_bdev, bio_sectors(bio), bio_op(bio));
+	return __part_start_io_acct(bio->bi_bdev, bio_sectors(bio),
+				    bio_op(bio), jiffies);
 }
 EXPORT_SYMBOL_GPL(bio_start_io_acct);
 
 unsigned long disk_start_io_acct(struct gendisk *disk, unsigned int sectors,
 				 unsigned int op)
 {
-	return __part_start_io_acct(disk->part0, sectors, op);
+	return __part_start_io_acct(disk->part0, sectors, op, jiffies);
 }
 EXPORT_SYMBOL(disk_start_io_acct);
 
@@ -1414,6 +1415,13 @@
 		req->q->integrity.profile->complete_fn(req, nr_bytes);
 #endif
 
+	/*
+	 * Upper layers may call blk_crypto_evict_key() anytime after the last
+	 * bio_endio().  Therefore, the keyslot must be released before that.
+	 */
+	if (blk_crypto_rq_has_keyslot(req) && nr_bytes >= blk_rq_bytes(req))
+		__blk_crypto_rq_put_keyslot(req);
+
 	if (unlikely(error && !blk_rq_is_passthrough(req) &&
 		     !(req->rq_flags & RQF_QUIET)))
 		print_req_error(req, error, __func__);
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-crypto-internal.h
+++ linux-xilinx-zynqmp-5.15.0/block/blk-crypto-internal.h
@@ -60,6 +60,11 @@
 	return rq->crypt_ctx;
 }
 
+static inline bool blk_crypto_rq_has_keyslot(struct request *rq)
+{
+	return rq->crypt_keyslot;
+}
+
 #else /* CONFIG_BLK_INLINE_ENCRYPTION */
 
 static inline bool bio_crypt_rq_ctx_compatible(struct request *rq,
@@ -93,6 +98,11 @@
 	return false;
 }
 
+static inline bool blk_crypto_rq_has_keyslot(struct request *rq)
+{
+	return false;
+}
+
 #endif /* CONFIG_BLK_INLINE_ENCRYPTION */
 
 void __bio_crypt_advance(struct bio *bio, unsigned int bytes);
@@ -127,14 +137,21 @@
 	return true;
 }
 
-blk_status_t __blk_crypto_init_request(struct request *rq);
-static inline blk_status_t blk_crypto_init_request(struct request *rq)
+blk_status_t __blk_crypto_rq_get_keyslot(struct request *rq);
+static inline blk_status_t blk_crypto_rq_get_keyslot(struct request *rq)
 {
 	if (blk_crypto_rq_is_encrypted(rq))
-		return __blk_crypto_init_request(rq);
+		return __blk_crypto_rq_get_keyslot(rq);
 	return BLK_STS_OK;
 }
 
+void __blk_crypto_rq_put_keyslot(struct request *rq);
+static inline void blk_crypto_rq_put_keyslot(struct request *rq)
+{
+	if (blk_crypto_rq_has_keyslot(rq))
+		__blk_crypto_rq_put_keyslot(rq);
+}
+
 void __blk_crypto_free_request(struct request *rq);
 static inline void blk_crypto_free_request(struct request *rq)
 {
@@ -173,7 +190,7 @@
 {
 
 	if (blk_crypto_rq_is_encrypted(rq))
-		return blk_crypto_init_request(rq);
+		return blk_crypto_rq_get_keyslot(rq);
 	return BLK_STS_OK;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-crypto.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-crypto.c
@@ -13,6 +13,7 @@
 #include <linux/blkdev.h>
 #include <linux/keyslot-manager.h>
 #include <linux/module.h>
+#include <linux/ratelimit.h>
 #include <linux/slab.h>
 
 #include "blk-crypto-internal.h"
@@ -216,26 +217,26 @@
 	return true;
 }
 
-blk_status_t __blk_crypto_init_request(struct request *rq)
+blk_status_t __blk_crypto_rq_get_keyslot(struct request *rq)
 {
 	return blk_ksm_get_slot_for_key(rq->q->ksm, rq->crypt_ctx->bc_key,
 					&rq->crypt_keyslot);
 }
 
-/**
- * __blk_crypto_free_request - Uninitialize the crypto fields of a request.
- *
- * @rq: The request whose crypto fields to uninitialize.
- *
- * Completely uninitializes the crypto fields of a request. If a keyslot has
- * been programmed into some inline encryption hardware, that keyslot is
- * released. The rq->crypt_ctx is also freed.
- */
-void __blk_crypto_free_request(struct request *rq)
+void __blk_crypto_rq_put_keyslot(struct request *rq)
 {
 	blk_ksm_put_slot(rq->crypt_keyslot);
+	rq->crypt_keyslot = NULL;
+}
+
+void __blk_crypto_free_request(struct request *rq)
+{
+	/* The keyslot, if one was needed, should have been released earlier. */
+	if (WARN_ON_ONCE(rq->crypt_keyslot))
+		__blk_crypto_rq_put_keyslot(rq);
+
 	mempool_free(rq->crypt_ctx, bio_crypt_ctx_pool);
-	blk_crypto_rq_set_defaults(rq);
+	rq->crypt_ctx = NULL;
 }
 
 /**
@@ -384,29 +385,39 @@
 }
 
 /**
- * blk_crypto_evict_key() - Evict a key from any inline encryption hardware
- *			    it may have been programmed into
- * @q: The request queue who's associated inline encryption hardware this key
- *     might have been programmed into
- * @key: The key to evict
- *
- * Upper layers (filesystems) must call this function to ensure that a key is
- * evicted from any hardware that it might have been programmed into.  The key
- * must not be in use by any in-flight IO when this function is called.
+ * blk_crypto_evict_key() - Evict a blk_crypto_key from a request_queue
+ * @q: a request_queue on which I/O using the key may have been done
+ * @key: the key to evict
+ *
+ * For a given request_queue, this function removes the given blk_crypto_key
+ * from the keyslot management structures and evicts it from any underlying
+ * hardware keyslot(s) or blk-crypto-fallback keyslot it may have been
+ * programmed into.
+ *
+ * Upper layers must call this before freeing the blk_crypto_key.  It must be
+ * called for every request_queue the key may have been used on.  The key must
+ * no longer be in use by any I/O when this function is called.
  *
- * Return: 0 on success or if key is not present in the q's ksm, -err on error.
+ * Context: May sleep.
  */
-int blk_crypto_evict_key(struct request_queue *q,
-			 const struct blk_crypto_key *key)
+void blk_crypto_evict_key(struct request_queue *q,
+			  const struct blk_crypto_key *key)
 {
-	if (blk_ksm_crypto_cfg_supported(q->ksm, &key->crypto_cfg))
-		return blk_ksm_evict_key(q->ksm, key);
+	int err;
 
+	if (blk_ksm_crypto_cfg_supported(q->ksm, &key->crypto_cfg))
+		err = blk_ksm_evict_key(q->ksm, key);
+	else
+		err = blk_crypto_fallback_evict_key(key);
 	/*
-	 * If the request queue's associated inline encryption hardware didn't
-	 * have support for the key, then the key might have been programmed
-	 * into the fallback keyslot manager, so try to evict from there.
+	 * An error can only occur here if the key failed to be evicted from a
+	 * keyslot (due to a hardware or driver issue) or is allegedly still in
+	 * use by I/O (due to a kernel bug).  Even in these cases, the key is
+	 * still unlinked from the keyslot management structures, and the caller
+	 * is allowed and expected to free it right away.  There's nothing
+	 * callers can do to handle errors, so just log them and return void.
 	 */
-	return blk_crypto_fallback_evict_key(key);
+	if (err)
+		pr_warn_ratelimited("error %d evicting key\n", err);
 }
 EXPORT_SYMBOL_GPL(blk_crypto_evict_key);
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-flush.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-flush.c
@@ -235,8 +235,10 @@
 	 * avoiding use-after-free.
 	 */
 	WRITE_ONCE(flush_rq->state, MQ_RQ_IDLE);
-	if (fq->rq_status != BLK_STS_OK)
+	if (fq->rq_status != BLK_STS_OK) {
 		error = fq->rq_status;
+		fq->rq_status = BLK_STS_OK;
+	}
 
 	if (!q->elevator) {
 		flush_rq->tag = BLK_MQ_NO_TAG;
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-integrity.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-integrity.c
@@ -212,61 +212,44 @@
 	return true;
 }
 
-struct integrity_sysfs_entry {
-	struct attribute attr;
-	ssize_t (*show)(struct blk_integrity *, char *);
-	ssize_t (*store)(struct blk_integrity *, const char *, size_t);
-};
-
-static ssize_t integrity_attr_show(struct kobject *kobj, struct attribute *attr,
-				   char *page)
+static inline struct blk_integrity *dev_to_bi(struct device *dev)
 {
-	struct gendisk *disk = container_of(kobj, struct gendisk, integrity_kobj);
-	struct blk_integrity *bi = &disk->queue->integrity;
-	struct integrity_sysfs_entry *entry =
-		container_of(attr, struct integrity_sysfs_entry, attr);
-
-	return entry->show(bi, page);
+	return &dev_to_disk(dev)->queue->integrity;
 }
 
-static ssize_t integrity_attr_store(struct kobject *kobj,
-				    struct attribute *attr, const char *page,
-				    size_t count)
+static ssize_t format_show(struct device *dev, struct device_attribute *attr,
+			   char *page)
 {
-	struct gendisk *disk = container_of(kobj, struct gendisk, integrity_kobj);
-	struct blk_integrity *bi = &disk->queue->integrity;
-	struct integrity_sysfs_entry *entry =
-		container_of(attr, struct integrity_sysfs_entry, attr);
-	ssize_t ret = 0;
+	struct blk_integrity *bi = dev_to_bi(dev);
 
-	if (entry->store)
-		ret = entry->store(bi, page, count);
-
-	return ret;
-}
-
-static ssize_t integrity_format_show(struct blk_integrity *bi, char *page)
-{
 	if (bi->profile && bi->profile->name)
-		return sprintf(page, "%s\n", bi->profile->name);
-	else
-		return sprintf(page, "none\n");
+		return sysfs_emit(page, "%s\n", bi->profile->name);
+	return sysfs_emit(page, "none\n");
 }
 
-static ssize_t integrity_tag_size_show(struct blk_integrity *bi, char *page)
+static ssize_t tag_size_show(struct device *dev, struct device_attribute *attr,
+			     char *page)
 {
-	return sprintf(page, "%u\n", bi->tag_size);
+	struct blk_integrity *bi = dev_to_bi(dev);
+
+	return sysfs_emit(page, "%u\n", bi->tag_size);
 }
 
-static ssize_t integrity_interval_show(struct blk_integrity *bi, char *page)
+static ssize_t protection_interval_bytes_show(struct device *dev,
+					      struct device_attribute *attr,
+					      char *page)
 {
-	return sprintf(page, "%u\n",
-		       bi->interval_exp ? 1 << bi->interval_exp : 0);
+	struct blk_integrity *bi = dev_to_bi(dev);
+
+	return sysfs_emit(page, "%u\n",
+			  bi->interval_exp ? 1 << bi->interval_exp : 0);
 }
 
-static ssize_t integrity_verify_store(struct blk_integrity *bi,
-				      const char *page, size_t count)
+static ssize_t read_verify_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *page, size_t count)
 {
+	struct blk_integrity *bi = dev_to_bi(dev);
 	char *p = (char *) page;
 	unsigned long val = simple_strtoul(p, &p, 10);
 
@@ -278,14 +261,20 @@
 	return count;
 }
 
-static ssize_t integrity_verify_show(struct blk_integrity *bi, char *page)
+static ssize_t read_verify_show(struct device *dev,
+				struct device_attribute *attr, char *page)
 {
-	return sprintf(page, "%d\n", (bi->flags & BLK_INTEGRITY_VERIFY) != 0);
+	struct blk_integrity *bi = dev_to_bi(dev);
+
+	return sysfs_emit(page, "%d\n", !!(bi->flags & BLK_INTEGRITY_VERIFY));
 }
 
-static ssize_t integrity_generate_store(struct blk_integrity *bi,
-					const char *page, size_t count)
+static ssize_t write_generate_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *page, size_t count)
 {
+	struct blk_integrity *bi = dev_to_bi(dev);
+
 	char *p = (char *) page;
 	unsigned long val = simple_strtoul(p, &p, 10);
 
@@ -297,68 +286,44 @@
 	return count;
 }
 
-static ssize_t integrity_generate_show(struct blk_integrity *bi, char *page)
+static ssize_t write_generate_show(struct device *dev,
+				   struct device_attribute *attr, char *page)
 {
-	return sprintf(page, "%d\n", (bi->flags & BLK_INTEGRITY_GENERATE) != 0);
-}
+	struct blk_integrity *bi = dev_to_bi(dev);
 
-static ssize_t integrity_device_show(struct blk_integrity *bi, char *page)
-{
-	return sprintf(page, "%u\n",
-		       (bi->flags & BLK_INTEGRITY_DEVICE_CAPABLE) != 0);
+	return sysfs_emit(page, "%d\n", !!(bi->flags & BLK_INTEGRITY_GENERATE));
 }
 
-static struct integrity_sysfs_entry integrity_format_entry = {
-	.attr = { .name = "format", .mode = 0444 },
-	.show = integrity_format_show,
-};
-
-static struct integrity_sysfs_entry integrity_tag_size_entry = {
-	.attr = { .name = "tag_size", .mode = 0444 },
-	.show = integrity_tag_size_show,
-};
-
-static struct integrity_sysfs_entry integrity_interval_entry = {
-	.attr = { .name = "protection_interval_bytes", .mode = 0444 },
-	.show = integrity_interval_show,
-};
-
-static struct integrity_sysfs_entry integrity_verify_entry = {
-	.attr = { .name = "read_verify", .mode = 0644 },
-	.show = integrity_verify_show,
-	.store = integrity_verify_store,
-};
+static ssize_t device_is_integrity_capable_show(struct device *dev,
+						struct device_attribute *attr,
+						char *page)
+{
+	struct blk_integrity *bi = dev_to_bi(dev);
 
-static struct integrity_sysfs_entry integrity_generate_entry = {
-	.attr = { .name = "write_generate", .mode = 0644 },
-	.show = integrity_generate_show,
-	.store = integrity_generate_store,
-};
+	return sysfs_emit(page, "%u\n",
+			  !!(bi->flags & BLK_INTEGRITY_DEVICE_CAPABLE));
+}
 
-static struct integrity_sysfs_entry integrity_device_entry = {
-	.attr = { .name = "device_is_integrity_capable", .mode = 0444 },
-	.show = integrity_device_show,
-};
+static DEVICE_ATTR_RO(format);
+static DEVICE_ATTR_RO(tag_size);
+static DEVICE_ATTR_RO(protection_interval_bytes);
+static DEVICE_ATTR_RW(read_verify);
+static DEVICE_ATTR_RW(write_generate);
+static DEVICE_ATTR_RO(device_is_integrity_capable);
 
 static struct attribute *integrity_attrs[] = {
-	&integrity_format_entry.attr,
-	&integrity_tag_size_entry.attr,
-	&integrity_interval_entry.attr,
-	&integrity_verify_entry.attr,
-	&integrity_generate_entry.attr,
-	&integrity_device_entry.attr,
-	NULL,
+	&dev_attr_format.attr,
+	&dev_attr_tag_size.attr,
+	&dev_attr_protection_interval_bytes.attr,
+	&dev_attr_read_verify.attr,
+	&dev_attr_write_generate.attr,
+	&dev_attr_device_is_integrity_capable.attr,
+	NULL
 };
-ATTRIBUTE_GROUPS(integrity);
 
-static const struct sysfs_ops integrity_ops = {
-	.show	= &integrity_attr_show,
-	.store	= &integrity_attr_store,
-};
-
-static struct kobj_type integrity_ktype = {
-	.default_groups = integrity_groups,
-	.sysfs_ops	= &integrity_ops,
+const struct attribute_group blk_integrity_attr_group = {
+	.name = "integrity",
+	.attrs = integrity_attrs,
 };
 
 static blk_status_t blk_integrity_nop_fn(struct blk_integrity_iter *iter)
@@ -431,27 +396,7 @@
 	if (!bi->profile)
 		return;
 
-	/* ensure all bios are off the integrity workqueue */
-	blk_flush_integrity();
 	blk_queue_flag_clear(QUEUE_FLAG_STABLE_WRITES, disk->queue);
 	memset(bi, 0, sizeof(*bi));
 }
 EXPORT_SYMBOL(blk_integrity_unregister);
-
-int blk_integrity_add(struct gendisk *disk)
-{
-	int ret;
-
-	ret = kobject_init_and_add(&disk->integrity_kobj, &integrity_ktype,
-				   &disk_to_dev(disk)->kobj, "%s", "integrity");
-	if (!ret)
-		kobject_uevent(&disk->integrity_kobj, KOBJ_ADD);
-	return ret;
-}
-
-void blk_integrity_del(struct gendisk *disk)
-{
-	kobject_uevent(&disk->integrity_kobj, KOBJ_REMOVE);
-	kobject_del(&disk->integrity_kobj);
-	kobject_put(&disk->integrity_kobj);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-ioc.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-ioc.c
@@ -265,6 +265,7 @@
 	INIT_RADIX_TREE(&ioc->icq_tree, GFP_ATOMIC);
 	INIT_HLIST_HEAD(&ioc->icq_list);
 	INIT_WORK(&ioc->release_work, ioc_release_fn);
+	ioc->ioprio = IOPRIO_DEFAULT;
 
 	/*
 	 * Try to install.  ioc shouldn't be installed if someone else
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-iocost.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-iocost.c
@@ -232,7 +232,9 @@
 
 	/* 1/64k is granular enough and can easily be handled w/ u32 */
 	WEIGHT_ONE		= 1 << 16,
+};
 
+enum {
 	/*
 	 * As vtime is used to calculate the cost of each IO, it needs to
 	 * be fairly high precision.  For example, it should be able to
@@ -256,6 +258,11 @@
 	VRATE_MIN		= VTIME_PER_USEC * VRATE_MIN_PPM / MILLION,
 	VRATE_CLAMP_ADJ_PCT	= 4,
 
+	/* switch iff the conditions are met for longer than this */
+	AUTOP_CYCLE_NSEC	= 10LLU * NSEC_PER_SEC,
+};
+
+enum {
 	/* if IOs end up waiting for requests, issue less */
 	RQ_WAIT_BUSY_PCT	= 5,
 
@@ -294,9 +301,6 @@
 	/* don't let cmds which take a very long time pin lagging for too long */
 	MAX_LAGGING_PERIODS	= 10,
 
-	/* switch iff the conditions are met for longer than this */
-	AUTOP_CYCLE_NSEC	= 10LLU * NSEC_PER_SEC,
-
 	/*
 	 * Count IO size in 4k pages.  The 12bit shift helps keeping
 	 * size-proportional components of cost calculation in closer
@@ -870,9 +874,14 @@
 
 	*page = *seqio = *randio = 0;
 
-	if (bps)
-		*page = DIV64_U64_ROUND_UP(VTIME_PER_SEC,
-					   DIV_ROUND_UP_ULL(bps, IOC_PAGE_SIZE));
+	if (bps) {
+		u64 bps_pages = DIV_ROUND_UP_ULL(bps, IOC_PAGE_SIZE);
+
+		if (bps_pages)
+			*page = DIV64_U64_ROUND_UP(VTIME_PER_SEC, bps_pages);
+		else
+			*page = 1;
+	}
 
 	if (seqiops) {
 		v = DIV64_U64_ROUND_UP(VTIME_PER_SEC, seqiops);
@@ -1078,7 +1087,14 @@
 		inuse = DIV64_U64_ROUND_UP(active * iocg->child_inuse_sum,
 					   iocg->child_active_sum);
 	} else {
-		inuse = clamp_t(u32, inuse, 1, active);
+		/*
+		 * It may be tempting to turn this into a clamp expression with
+		 * a lower limit of 1 but active may be 0, which cannot be used
+		 * as an upper limit in that situation. This expression allows
+		 * active to clamp inuse unless it is 0, in which case inuse
+		 * becomes 1.
+		 */
+		inuse = min(inuse, active) ?: 1;
 	}
 
 	iocg->last_inuse = iocg->inuse;
@@ -1327,16 +1343,24 @@
 {
 	struct ioc *ioc = iocg->ioc;
 	struct blkcg_gq *blkg = iocg_to_blkg(iocg);
-	u64 tdelta, delay, new_delay;
+	u64 tdelta, delay, new_delay, shift;
 	s64 vover, vover_pct;
 	u32 hwa;
 
 	lockdep_assert_held(&iocg->waitq.lock);
 
+	/*
+	 * If the delay is set by another CPU, we may be in the past. No need to
+	 * change anything if so. This avoids decay calculation underflow.
+	 */
+	if (time_before64(now->now, iocg->delay_at))
+		return false;
+
 	/* calculate the current delay in effect - 1/2 every second */
 	tdelta = now->now - iocg->delay_at;
-	if (iocg->delay)
-		delay = iocg->delay >> div64_u64(tdelta, USEC_PER_SEC);
+	shift = div64_u64(tdelta, USEC_PER_SEC);
+	if (iocg->delay && shift < BITS_PER_LONG)
+		delay = iocg->delay >> shift;
 	else
 		delay = 0;
 
@@ -2051,7 +2075,7 @@
 			      struct ioc_now *now)
 {
 	struct ioc_gq *iocg;
-	u64 dur, usage_pct, nr_cycles;
+	u64 dur, usage_pct, nr_cycles, nr_cycles_shift;
 
 	/* if no debtor, reset the cycle */
 	if (!nr_debtors) {
@@ -2113,10 +2137,12 @@
 		old_debt = iocg->abs_vdebt;
 		old_delay = iocg->delay;
 
+		nr_cycles_shift = min_t(u64, nr_cycles, BITS_PER_LONG - 1);
 		if (iocg->abs_vdebt)
-			iocg->abs_vdebt = iocg->abs_vdebt >> nr_cycles ?: 1;
+			iocg->abs_vdebt = iocg->abs_vdebt >> nr_cycles_shift ?: 1;
+
 		if (iocg->delay)
-			iocg->delay = iocg->delay >> nr_cycles ?: 1;
+			iocg->delay = iocg->delay >> nr_cycles_shift ?: 1;
 
 		iocg_kick_waitq(iocg, true, now);
 
@@ -2311,11 +2337,28 @@
 			hwm = current_hweight_max(iocg);
 			new_hwi = hweight_after_donation(iocg, old_hwi, hwm,
 							 usage, &now);
-			if (new_hwi < hwm) {
+			/*
+			 * Donation calculation assumes hweight_after_donation
+			 * to be positive, a condition that a donor w/ hwa < 2
+			 * can't meet. Don't bother with donation if hwa is
+			 * below 2. It's not gonna make a meaningful difference
+			 * anyway.
+			 */
+			if (new_hwi < hwm && hwa >= 2) {
 				iocg->hweight_donating = hwa;
 				iocg->hweight_after_donation = new_hwi;
 				list_add(&iocg->surplus_list, &surpluses);
-			} else {
+			} else if (!iocg->abs_vdebt) {
+				/*
+				 * @iocg doesn't have enough to donate. Reset
+				 * its inuse to active.
+				 *
+				 * Don't reset debtors as their inuse's are
+				 * owned by debt handling. This shouldn't affect
+				 * donation calculuation in any meaningful way
+				 * as @iocg doesn't have a meaningful amount of
+				 * share anyway.
+				 */
 				TRACE_IOCG_PATH(inuse_shortage, iocg, &now,
 						iocg->inuse, iocg->active,
 						iocg->hweight_inuse, new_hwi);
@@ -2422,6 +2465,7 @@
 	u32 hwi, adj_step;
 	s64 margin;
 	u64 cost, new_inuse;
+	unsigned long flags;
 
 	current_hweight(iocg, NULL, &hwi);
 	old_hwi = hwi;
@@ -2440,11 +2484,11 @@
 	    iocg->inuse == iocg->active)
 		return cost;
 
-	spin_lock_irq(&ioc->lock);
+	spin_lock_irqsave(&ioc->lock, flags);
 
 	/* we own inuse only when @iocg is in the normal active state */
 	if (iocg->abs_vdebt || list_empty(&iocg->active_list)) {
-		spin_unlock_irq(&ioc->lock);
+		spin_unlock_irqrestore(&ioc->lock, flags);
 		return cost;
 	}
 
@@ -2465,7 +2509,7 @@
 	} while (time_after64(vtime + cost, now->vnow) &&
 		 iocg->inuse != iocg->active);
 
-	spin_unlock_irq(&ioc->lock);
+	spin_unlock_irqrestore(&ioc->lock, flags);
 
 	TRACE_IOCG_PATH(inuse_adjust, iocg, now,
 			old_inuse, iocg->inuse, old_hwi, hwi);
@@ -2876,15 +2920,21 @@
 	 * called before policy activation completion, can't assume that the
 	 * target bio has an iocg associated and need to test for NULL iocg.
 	 */
-	rq_qos_add(q, rqos);
+	ret = rq_qos_add(q, rqos);
+	if (ret)
+		goto err_free_ioc;
+
 	ret = blkcg_activate_policy(q, &blkcg_policy_iocost);
-	if (ret) {
-		rq_qos_del(q, rqos);
-		free_percpu(ioc->pcpu_stat);
-		kfree(ioc);
-		return ret;
-	}
+	if (ret)
+		goto err_del_qos;
 	return 0;
+
+err_del_qos:
+	rq_qos_del(q, rqos);
+err_free_ioc:
+	free_percpu(ioc->pcpu_stat);
+	kfree(ioc);
+	return ret;
 }
 
 static struct blkcg_policy_data *ioc_cpd_alloc(gfp_t gfp)
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-iolatency.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-iolatency.c
@@ -86,7 +86,17 @@
 struct blk_iolatency {
 	struct rq_qos rqos;
 	struct timer_list timer;
-	atomic_t enabled;
+
+	/*
+	 * ->enabled is the master enable switch gating the throttling logic and
+	 * inflight tracking. The number of cgroups which have iolat enabled is
+	 * tracked in ->enable_cnt, and ->enable is flipped on/off accordingly
+	 * from ->enable_work with the request_queue frozen. For details, See
+	 * blkiolatency_enable_work_fn().
+	 */
+	bool enabled;
+	atomic_t enable_cnt;
+	struct work_struct enable_work;
 };
 
 static inline struct blk_iolatency *BLKIOLATENCY(struct rq_qos *rqos)
@@ -94,11 +104,6 @@
 	return container_of(rqos, struct blk_iolatency, rqos);
 }
 
-static inline bool blk_iolatency_enabled(struct blk_iolatency *blkiolat)
-{
-	return atomic_read(&blkiolat->enabled) > 0;
-}
-
 struct child_latency_info {
 	spinlock_t lock;
 
@@ -463,7 +468,7 @@
 	struct blkcg_gq *blkg = bio->bi_blkg;
 	bool issue_as_root = bio_issue_as_root_blkg(bio);
 
-	if (!blk_iolatency_enabled(blkiolat))
+	if (!blkiolat->enabled)
 		return;
 
 	while (blkg && blkg->parent) {
@@ -593,19 +598,17 @@
 	u64 window_start;
 	u64 now;
 	bool issue_as_root = bio_issue_as_root_blkg(bio);
-	bool enabled = false;
 	int inflight = 0;
 
 	blkg = bio->bi_blkg;
-	if (!blkg || !bio_flagged(bio, BIO_TRACKED))
+	if (!blkg || !bio_flagged(bio, BIO_QOS_THROTTLED))
 		return;
 
 	iolat = blkg_to_lat(bio->bi_blkg);
 	if (!iolat)
 		return;
 
-	enabled = blk_iolatency_enabled(iolat->blkiolat);
-	if (!enabled)
+	if (!iolat->blkiolat->enabled)
 		return;
 
 	now = ktime_to_ns(ktime_get());
@@ -644,6 +647,7 @@
 	struct blk_iolatency *blkiolat = BLKIOLATENCY(rqos);
 
 	del_timer_sync(&blkiolat->timer);
+	flush_work(&blkiolat->enable_work);
 	blkcg_deactivate_policy(rqos->q, &blkcg_policy_iolatency);
 	kfree(blkiolat);
 }
@@ -715,6 +719,44 @@
 	rcu_read_unlock();
 }
 
+/**
+ * blkiolatency_enable_work_fn - Enable or disable iolatency on the device
+ * @work: enable_work of the blk_iolatency of interest
+ *
+ * iolatency needs to keep track of the number of in-flight IOs per cgroup. This
+ * is relatively expensive as it involves walking up the hierarchy twice for
+ * every IO. Thus, if iolatency is not enabled in any cgroup for the device, we
+ * want to disable the in-flight tracking.
+ *
+ * We have to make sure that the counting is balanced - we don't want to leak
+ * the in-flight counts by disabling accounting in the completion path while IOs
+ * are in flight. This is achieved by ensuring that no IO is in flight by
+ * freezing the queue while flipping ->enabled. As this requires a sleepable
+ * context, ->enabled flipping is punted to this work function.
+ */
+static void blkiolatency_enable_work_fn(struct work_struct *work)
+{
+	struct blk_iolatency *blkiolat = container_of(work, struct blk_iolatency,
+						      enable_work);
+	bool enabled;
+
+	/*
+	 * There can only be one instance of this function running for @blkiolat
+	 * and it's guaranteed to be executed at least once after the latest
+	 * ->enabled_cnt modification. Acting on the latest ->enable_cnt is
+	 * sufficient.
+	 *
+	 * Also, we know @blkiolat is safe to access as ->enable_work is flushed
+	 * in blkcg_iolatency_exit().
+	 */
+	enabled = atomic_read(&blkiolat->enable_cnt);
+	if (enabled != blkiolat->enabled) {
+		blk_mq_freeze_queue(blkiolat->rqos.q);
+		blkiolat->enabled = enabled;
+		blk_mq_unfreeze_queue(blkiolat->rqos.q);
+	}
+}
+
 int blk_iolatency_init(struct request_queue *q)
 {
 	struct blk_iolatency *blkiolat;
@@ -730,27 +772,29 @@
 	rqos->ops = &blkcg_iolatency_ops;
 	rqos->q = q;
 
-	rq_qos_add(q, rqos);
-
+	ret = rq_qos_add(q, rqos);
+	if (ret)
+		goto err_free;
 	ret = blkcg_activate_policy(q, &blkcg_policy_iolatency);
-	if (ret) {
-		rq_qos_del(q, rqos);
-		kfree(blkiolat);
-		return ret;
-	}
+	if (ret)
+		goto err_qos_del;
 
 	timer_setup(&blkiolat->timer, blkiolatency_timer_fn, 0);
+	INIT_WORK(&blkiolat->enable_work, blkiolatency_enable_work_fn);
 
 	return 0;
+
+err_qos_del:
+	rq_qos_del(q, rqos);
+err_free:
+	kfree(blkiolat);
+	return ret;
 }
 
-/*
- * return 1 for enabling iolatency, return -1 for disabling iolatency, otherwise
- * return 0.
- */
-static int iolatency_set_min_lat_nsec(struct blkcg_gq *blkg, u64 val)
+static void iolatency_set_min_lat_nsec(struct blkcg_gq *blkg, u64 val)
 {
 	struct iolatency_grp *iolat = blkg_to_lat(blkg);
+	struct blk_iolatency *blkiolat = iolat->blkiolat;
 	u64 oldval = iolat->min_lat_nsec;
 
 	iolat->min_lat_nsec = val;
@@ -758,13 +802,15 @@
 	iolat->cur_win_nsec = min_t(u64, iolat->cur_win_nsec,
 				    BLKIOLATENCY_MAX_WIN_SIZE);
 
-	if (!oldval && val)
-		return 1;
+	if (!oldval && val) {
+		if (atomic_inc_return(&blkiolat->enable_cnt) == 1)
+			schedule_work(&blkiolat->enable_work);
+	}
 	if (oldval && !val) {
 		blkcg_clear_delay(blkg);
-		return -1;
+		if (atomic_dec_return(&blkiolat->enable_cnt) == 0)
+			schedule_work(&blkiolat->enable_work);
 	}
-	return 0;
 }
 
 static void iolatency_clear_scaling(struct blkcg_gq *blkg)
@@ -796,7 +842,6 @@
 	u64 lat_val = 0;
 	u64 oldval;
 	int ret;
-	int enable = 0;
 
 	ret = blkg_conf_prep(blkcg, &blkcg_policy_iolatency, buf, &ctx);
 	if (ret)
@@ -831,41 +876,12 @@
 	blkg = ctx.blkg;
 	oldval = iolat->min_lat_nsec;
 
-	enable = iolatency_set_min_lat_nsec(blkg, lat_val);
-	if (enable) {
-		if (!blk_get_queue(blkg->q)) {
-			ret = -ENODEV;
-			goto out;
-		}
-
-		blkg_get(blkg);
-	}
-
-	if (oldval != iolat->min_lat_nsec) {
+	iolatency_set_min_lat_nsec(blkg, lat_val);
+	if (oldval != iolat->min_lat_nsec)
 		iolatency_clear_scaling(blkg);
-	}
-
 	ret = 0;
 out:
 	blkg_conf_finish(&ctx);
-	if (ret == 0 && enable) {
-		struct iolatency_grp *tmp = blkg_to_lat(blkg);
-		struct blk_iolatency *blkiolat = tmp->blkiolat;
-
-		blk_mq_freeze_queue(blkg->q);
-
-		if (enable == 1)
-			atomic_inc(&blkiolat->enabled);
-		else if (enable == -1)
-			atomic_dec(&blkiolat->enabled);
-		else
-			WARN_ON_ONCE(1);
-
-		blk_mq_unfreeze_queue(blkg->q);
-
-		blkg_put(blkg);
-		blk_put_queue(blkg->q);
-	}
 	return ret ?: nbytes;
 }
 
@@ -1006,14 +1022,8 @@
 {
 	struct iolatency_grp *iolat = pd_to_lat(pd);
 	struct blkcg_gq *blkg = lat_to_blkg(iolat);
-	struct blk_iolatency *blkiolat = iolat->blkiolat;
-	int ret;
 
-	ret = iolatency_set_min_lat_nsec(blkg, 0);
-	if (ret == 1)
-		atomic_inc(&blkiolat->enabled);
-	if (ret == -1)
-		atomic_dec(&blkiolat->enabled);
+	iolatency_set_min_lat_nsec(blkg, 0);
 	iolatency_clear_scaling(blkg);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-map.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-map.c
@@ -446,7 +446,7 @@
 		if (bytes > len)
 			bytes = len;
 
-		page = alloc_page(GFP_NOIO | gfp_mask);
+		page = alloc_page(GFP_NOIO | __GFP_ZERO | gfp_mask);
 		if (!page)
 			goto cleanup;
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-merge.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-merge.c
@@ -7,6 +7,7 @@
 #include <linux/bio.h>
 #include <linux/blkdev.h>
 #include <linux/scatterlist.h>
+#include <linux/blk-cgroup.h>
 
 #include <trace/events/block.h>
 
@@ -278,6 +279,16 @@
 	*segs = nsegs;
 	return NULL;
 split:
+	/*
+	 * We can't sanely support splitting for a REQ_NOWAIT bio. End it
+	 * with EAGAIN if splitting is required and return an error pointer.
+	 */
+	if (bio->bi_opf & REQ_NOWAIT) {
+		bio->bi_status = BLK_STS_AGAIN;
+		bio_endio(bio);
+		return ERR_PTR(-EAGAIN);
+	}
+
 	*segs = nsegs;
 
 	/*
@@ -337,11 +348,13 @@
 			break;
 		}
 		split = blk_bio_segment_split(q, *bio, &q->bio_split, nr_segs);
+		if (IS_ERR(split))
+			*bio = split = NULL;
 		break;
 	}
 
 	if (split) {
-		/* there isn't chance to merge the splitted bio */
+		/* there isn't chance to merge the split bio */
 		split->bi_opf |= REQ_NOMERGE;
 
 		bio_chain(split, *bio);
@@ -561,6 +574,9 @@
 static inline int ll_new_hw_segment(struct request *req, struct bio *bio,
 		unsigned int nr_phys_segs)
 {
+	if (!blk_cgroup_mergeable(req, bio))
+		goto no_merge;
+
 	if (blk_integrity_merge_bio(req->q, req, bio) == false)
 		goto no_merge;
 
@@ -657,6 +673,9 @@
 	if (total_phys_segments > blk_rq_get_max_segments(req))
 		return 0;
 
+	if (!blk_cgroup_mergeable(req, next->bio))
+		return 0;
+
 	if (blk_integrity_merge_rq(q, req, next) == false)
 		return 0;
 
@@ -799,6 +818,8 @@
 	if (!blk_discard_mergable(req))
 		elv_merge_requests(q, req, next);
 
+	blk_crypto_rq_put_keyslot(next);
+
 	/*
 	 * 'next' is going away, so update stats accordingly
 	 */
@@ -863,6 +884,10 @@
 	if (rq->rq_disk != bio->bi_bdev->bd_disk)
 		return false;
 
+	/* don't merge across cgroup boundaries */
+	if (!blk_cgroup_mergeable(rq, bio))
+		return false;
+
 	/* only merge integrity protected bio into ditto rq */
 	if (blk_integrity_merge_bio(rq->q, rq, bio) == false)
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-mq-debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-mq-debugfs.c
@@ -879,6 +879,9 @@
 	char name[20];
 	int i;
 
+	if (!q->debugfs_dir)
+		return;
+
 	snprintf(name, sizeof(name), "hctx%u", hctx->queue_num);
 	hctx->debugfs_dir = debugfs_create_dir(name, q->debugfs_dir);
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-mq-sched.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-mq-sched.c
@@ -45,8 +45,7 @@
 }
 
 /*
- * Mark a hardware queue as needing a restart. For shared queues, maintain
- * a count of how many hardware queues are marked for restart.
+ * Mark a hardware queue as needing a restart.
  */
 void blk_mq_sched_mark_restart_hctx(struct blk_mq_hw_ctx *hctx)
 {
@@ -110,7 +109,7 @@
 /*
  * Only SCSI implements .get_budget and .put_budget, and SCSI restarts
  * its queue by itself in its completion handler, so we don't need to
- * restart queue if .get_budget() returns BLK_STS_NO_RESOURCE.
+ * restart queue if .get_budget() fails to get the budget.
  *
  * Returns -EAGAIN if hctx->dispatch was found non-empty and run_work has to
  * be run again.  This is necessary to avoid starving flushes.
@@ -208,11 +207,18 @@
 
 static int blk_mq_do_dispatch_sched(struct blk_mq_hw_ctx *hctx)
 {
+	unsigned long end = jiffies + HZ;
 	int ret;
 
 	do {
 		ret = __blk_mq_do_dispatch_sched(hctx);
-	} while (ret == 1);
+		if (ret != 1)
+			break;
+		if (need_resched() || time_is_before_jiffies(end)) {
+			blk_mq_delay_run_hw_queue(hctx, 0);
+			break;
+		}
+	} while (1);
 
 	return ret;
 }
@@ -231,7 +237,7 @@
 /*
  * Only SCSI implements .get_budget and .put_budget, and SCSI restarts
  * its queue by itself in its completion handler, so we don't need to
- * restart queue if .get_budget() returns BLK_STS_NO_RESOURCE.
+ * restart queue if .get_budget() fails to get the budget.
  *
  * Returns -EAGAIN if hctx->dispatch was found non-empty and run_work has to
  * be run again.  This is necessary to avoid starving flushes.
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-mq-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-mq-sysfs.c
@@ -187,7 +187,7 @@
 {
 	struct request_queue *q = hctx->queue;
 	struct blk_mq_ctx *ctx;
-	int i, ret;
+	int i, j, ret;
 
 	if (!hctx->nr_ctx)
 		return 0;
@@ -199,9 +199,16 @@
 	hctx_for_each_ctx(hctx, ctx, i) {
 		ret = kobject_add(&ctx->kobj, &hctx->kobj, "cpu%u", ctx->cpu);
 		if (ret)
-			break;
+			goto out;
 	}
 
+	return 0;
+out:
+	hctx_for_each_ctx(hctx, ctx, j) {
+		if (j < i)
+			kobject_del(&ctx->kobj);
+	}
+	kobject_del(&hctx->kobj);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-mq.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-mq.c
@@ -457,7 +457,8 @@
 	 * allocator for this for the rare use case of a command tied to
 	 * a specific queue.
 	 */
-	if (WARN_ON_ONCE(!(flags & (BLK_MQ_REQ_NOWAIT | BLK_MQ_REQ_RESERVED))))
+	if (WARN_ON_ONCE(!(flags & BLK_MQ_REQ_NOWAIT)) ||
+	    WARN_ON_ONCE(!(flags & BLK_MQ_REQ_RESERVED)))
 		return ERR_PTR(-EINVAL);
 
 	if (hctx_idx >= q->nr_hw_queues)
@@ -476,6 +477,8 @@
 	if (!blk_mq_hw_queue_mapped(data.hctx))
 		goto out_queue_exit;
 	cpu = cpumask_first_and(data.hctx->cpumask, cpu_online_mask);
+	if (cpu >= nr_cpu_ids)
+		goto out_queue_exit;
 	data.ctx = __blk_mq_get_ctx(q, cpu);
 
 	if (!q->elevator)
@@ -763,7 +766,6 @@
 	/* this request will be re-inserted to io scheduler queue */
 	blk_mq_sched_requeue_request(rq);
 
-	BUG_ON(!list_empty(&rq->queuelist));
 	blk_mq_add_to_requeue_list(rq, true, kick_requeue_list);
 }
 EXPORT_SYMBOL(blk_mq_requeue_request);
@@ -1175,6 +1177,22 @@
 	__add_wait_queue(wq, wait);
 
 	/*
+	 * Add one explicit barrier since blk_mq_get_driver_tag() may
+	 * not imply barrier in case of failure.
+	 *
+	 * Order adding us to wait queue and allocating driver tag.
+	 *
+	 * The pair is the one implied in sbitmap_queue_wake_up() which
+	 * orders clearing sbitmap tag bits and waitqueue_active() in
+	 * __sbitmap_queue_wake_up(), since waitqueue_active() is lockless
+	 *
+	 * Otherwise, re-order of adding wait queue and getting driver tag
+	 * may cause __sbitmap_queue_wake_up() to wake up nothing because
+	 * the waitqueue_active() may not observe us in wait queue.
+	 */
+	smp_mb();
+
+	/*
 	 * It's possible that a tag was freed in the window between the
 	 * allocation failure and adding the hardware queue to the wait
 	 * queue.
@@ -1399,7 +1417,8 @@
 	/* If we didn't flush the entire list, we could have told the driver
 	 * there was more coming, but that turned out to be a lie.
 	 */
-	if ((!list_empty(list) || errors) && q->mq_ops->commit_rqs && queued)
+	if ((!list_empty(list) || errors || needs_resource ||
+	     ret == BLK_STS_DEV_RESOURCE) && q->mq_ops->commit_rqs && queued)
 		q->mq_ops->commit_rqs(hctx);
 	/*
 	 * Any items that need requeuing? Stuff them into hctx->dispatch,
@@ -1643,8 +1662,7 @@
  */
 static struct blk_mq_hw_ctx *blk_mq_get_sq_hctx(struct request_queue *q)
 {
-	struct blk_mq_hw_ctx *hctx;
-
+	struct blk_mq_ctx *ctx = blk_mq_get_ctx(q);
 	/*
 	 * If the IO scheduler does not respect hardware queues when
 	 * dispatching, we just don't bother with multiple HW queues and
@@ -1652,8 +1670,8 @@
 	 * just causes lock contention inside the scheduler and pointless cache
 	 * bouncing.
 	 */
-	hctx = blk_mq_map_queue_type(q, HCTX_TYPE_DEFAULT,
-				     raw_smp_processor_id());
+	struct blk_mq_hw_ctx *hctx = blk_mq_map_queue(q, 0, ctx);
+
 	if (!blk_mq_hctx_stopped(hctx))
 		return hctx;
 	return NULL;
@@ -1795,6 +1813,12 @@
 		return;
 
 	clear_bit(BLK_MQ_S_STOPPED, &hctx->state);
+	/*
+	 * Pairs with the smp_mb() in blk_mq_hctx_stopped() to order the
+	 * clearing of BLK_MQ_S_STOPPED above and the checking of dispatch
+	 * list in the subsequent routine.
+	 */
+	smp_mb__after_atomic();
 	blk_mq_run_hw_queue(hctx, async);
 }
 EXPORT_SYMBOL_GPL(blk_mq_start_stopped_hw_queue);
@@ -2111,6 +2135,7 @@
 		list_del_init(&rq->queuelist);
 		ret = blk_mq_request_issue_directly(rq, list_empty(list));
 		if (ret != BLK_STS_OK) {
+			errors++;
 			if (ret == BLK_STS_RESOURCE ||
 					ret == BLK_STS_DEV_RESOURCE) {
 				blk_mq_request_bypass_insert(rq, false,
@@ -2118,7 +2143,6 @@
 				break;
 			}
 			blk_mq_end_request(rq, ret);
-			errors++;
 		} else
 			queued++;
 	}
@@ -2148,14 +2172,14 @@
 }
 
 /*
- * Allow 4x BLK_MAX_REQUEST_COUNT requests on plug queue for multiple
+ * Allow 2x BLK_MAX_REQUEST_COUNT requests on plug queue for multiple
  * queues. This is important for md arrays to benefit from merging
  * requests.
  */
 static inline unsigned short blk_plug_max_rq_count(struct blk_plug *plug)
 {
 	if (plug->multiple_queues)
-		return BLK_MAX_REQUEST_COUNT * 4;
+		return BLK_MAX_REQUEST_COUNT * 2;
 	return BLK_MAX_REQUEST_COUNT;
 }
 
@@ -2192,6 +2216,8 @@
 
 	blk_queue_bounce(q, &bio);
 	__blk_queue_split(&bio, &nr_segs);
+	if (!bio)
+		goto queue_exit;
 
 	if (!bio_integrity_prep(bio))
 		goto queue_exit;
@@ -2224,7 +2250,7 @@
 
 	blk_mq_bio_to_request(rq, bio, nr_segs);
 
-	ret = blk_crypto_init_request(rq);
+	ret = blk_crypto_rq_get_keyslot(rq);
 	if (ret != BLK_STS_OK) {
 		bio->bi_status = ret;
 		bio_endio(bio);
@@ -4019,6 +4045,19 @@
 }
 EXPORT_SYMBOL(blk_mq_rq_cpu);
 
+void blk_mq_cancel_work_sync(struct request_queue *q)
+{
+	if (queue_is_mq(q)) {
+		struct blk_mq_hw_ctx *hctx;
+		int i;
+
+		cancel_delayed_work_sync(&q->requeue_work);
+
+		queue_for_each_hw_ctx(q, hctx, i)
+			cancel_delayed_work_sync(&hctx->run_work);
+	}
+}
+
 static int __init blk_mq_init(void)
 {
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-mq.h
+++ linux-xilinx-zynqmp-5.15.0/block/blk-mq.h
@@ -129,6 +129,8 @@
 extern void blk_mq_sysfs_unregister(struct request_queue *q);
 extern void blk_mq_hctx_kobj_init(struct blk_mq_hw_ctx *hctx);
 
+void blk_mq_cancel_work_sync(struct request_queue *q);
+
 void blk_mq_release(struct request_queue *q);
 
 static inline struct blk_mq_ctx *__blk_mq_get_ctx(struct request_queue *q,
@@ -175,6 +177,19 @@
 
 static inline bool blk_mq_hctx_stopped(struct blk_mq_hw_ctx *hctx)
 {
+	/* Fast path: hardware queue is not stopped most of the time. */
+	if (likely(!test_bit(BLK_MQ_S_STOPPED, &hctx->state)))
+		return false;
+
+	/*
+	 * This barrier is used to order adding of dispatch list before and
+	 * the test of BLK_MQ_S_STOPPED below. Pairs with the memory barrier
+	 * in blk_mq_start_stopped_hw_queue() so that dispatch code could
+	 * either see BLK_MQ_S_STOPPED is cleared or dispatch list is not
+	 * empty to avoid missing dispatching requests.
+	 */
+	smp_mb();
+
 	return test_bit(BLK_MQ_S_STOPPED, &hctx->state);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-pm.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-pm.c
@@ -163,27 +163,19 @@
 /**
  * blk_post_runtime_resume - Post runtime resume processing
  * @q: the queue of the device
- * @err: return value of the device's runtime_resume function
  *
  * Description:
- *    Update the queue's runtime status according to the return value of the
- *    device's runtime_resume function. If the resume was successful, call
- *    blk_set_runtime_active() to do the real work of restarting the queue.
+ *    For historical reasons, this routine merely calls blk_set_runtime_active()
+ *    to do the real work of restarting the queue.  It does this regardless of
+ *    whether the device's runtime-resume succeeded; even if it failed the
+ *    driver or error handler will need to communicate with the device.
  *
  *    This function should be called near the end of the device's
  *    runtime_resume callback.
  */
-void blk_post_runtime_resume(struct request_queue *q, int err)
+void blk_post_runtime_resume(struct request_queue *q)
 {
-	if (!q->dev)
-		return;
-	if (!err) {
-		blk_set_runtime_active(q);
-	} else {
-		spin_lock_irq(&q->queue_lock);
-		q->rpm_status = RPM_SUSPENDED;
-		spin_unlock_irq(&q->queue_lock);
-	}
+	blk_set_runtime_active(q);
 }
 EXPORT_SYMBOL(blk_post_runtime_resume);
 
@@ -201,7 +193,7 @@
  * runtime PM status and re-enable peeking requests from the queue. It
  * should be called before first request is added to the queue.
  *
- * This function is also called by blk_post_runtime_resume() for successful
+ * This function is also called by blk_post_runtime_resume() for
  * runtime resumes.  It does everything necessary to restart the queue.
  */
 void blk_set_runtime_active(struct request_queue *q)
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-rq-qos.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-rq-qos.c
@@ -225,8 +225,8 @@
 
 	data->got_token = true;
 	smp_wmb();
-	list_del_init(&curr->entry);
 	wake_up_process(data->task);
+	list_del_init_careful(&curr->entry);
 	return 1;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-rq-qos.h
+++ linux-xilinx-zynqmp-5.15.0/block/blk-rq-qos.h
@@ -86,7 +86,7 @@
 	init_waitqueue_head(&rq_wait->wait);
 }
 
-static inline void rq_qos_add(struct request_queue *q, struct rq_qos *rqos)
+static inline int rq_qos_add(struct request_queue *q, struct rq_qos *rqos)
 {
 	/*
 	 * No IO can be in-flight when adding rqos, so freeze queue, which
@@ -98,6 +98,8 @@
 	blk_mq_freeze_queue(q);
 
 	spin_lock_irq(&q->queue_lock);
+	if (rq_qos_id(q, rqos->id))
+		goto ebusy;
 	rqos->next = q->rq_qos;
 	q->rq_qos = rqos;
 	spin_unlock_irq(&q->queue_lock);
@@ -106,6 +108,13 @@
 
 	if (rqos->ops->debugfs_attrs)
 		blk_mq_debugfs_register_rqos(rqos);
+
+	return 0;
+ebusy:
+	spin_unlock_irq(&q->queue_lock);
+	blk_mq_unfreeze_queue(q);
+	return -EBUSY;
+
 }
 
 static inline void rq_qos_del(struct request_queue *q, struct rq_qos *rqos)
@@ -177,21 +186,22 @@
 		__rq_qos_requeue(q->rq_qos, rq);
 }
 
-static inline void rq_qos_done_bio(struct request_queue *q, struct bio *bio)
+static inline void rq_qos_done_bio(struct bio *bio)
 {
-	if (q->rq_qos)
-		__rq_qos_done_bio(q->rq_qos, bio);
+	if (bio->bi_bdev && (bio_flagged(bio, BIO_QOS_THROTTLED) ||
+			     bio_flagged(bio, BIO_QOS_MERGED))) {
+		struct request_queue *q = bdev_get_queue(bio->bi_bdev);
+		if (q->rq_qos)
+			__rq_qos_done_bio(q->rq_qos, bio);
+	}
 }
 
 static inline void rq_qos_throttle(struct request_queue *q, struct bio *bio)
 {
-	/*
-	 * BIO_TRACKED lets controllers know that a bio went through the
-	 * normal rq_qos path.
-	 */
-	bio_set_flag(bio, BIO_TRACKED);
-	if (q->rq_qos)
+	if (q->rq_qos) {
+		bio_set_flag(bio, BIO_QOS_THROTTLED);
 		__rq_qos_throttle(q->rq_qos, bio);
+	}
 }
 
 static inline void rq_qos_track(struct request_queue *q, struct request *rq,
@@ -204,8 +214,10 @@
 static inline void rq_qos_merge(struct request_queue *q, struct request *rq,
 				struct bio *bio)
 {
-	if (q->rq_qos)
+	if (q->rq_qos) {
+		bio_set_flag(bio, BIO_QOS_MERGED);
 		__rq_qos_merge(q->rq_qos, rq, bio);
+	}
 }
 
 static inline void rq_qos_queue_depth_changed(struct request_queue *q)
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-settings.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-settings.c
@@ -136,7 +136,7 @@
 	limits->max_hw_sectors = max_hw_sectors;
 
 	max_sectors = min_not_zero(max_hw_sectors, limits->max_dev_sectors);
-	max_sectors = min_t(unsigned int, max_sectors, BLK_DEF_MAX_SECTORS);
+	max_sectors = min(max_sectors, BLK_DEF_MAX_SECTORS);
 	max_sectors = round_down(max_sectors,
 				 limits->logical_block_size >> SECTOR_SHIFT);
 	limits->max_sectors = max_sectors;
@@ -647,6 +647,10 @@
 	t->zone_write_granularity = max(t->zone_write_granularity,
 					b->zone_write_granularity);
 	t->zoned = max(t->zoned, b->zoned);
+	if (!t->zoned) {
+		t->zone_write_granularity = 0;
+		t->max_zone_append_sectors = 0;
+	}
 	return ret;
 }
 EXPORT_SYMBOL(blk_stack_limits);
@@ -875,6 +879,7 @@
 void blk_queue_set_zoned(struct gendisk *disk, enum blk_zoned_model model)
 {
 	struct request_queue *q = disk->queue;
+	unsigned int old_model = q->limits.zoned;
 
 	switch (model) {
 	case BLK_ZONED_HM:
@@ -912,7 +917,7 @@
 		 */
 		blk_queue_zone_write_granularity(q,
 						queue_logical_block_size(q));
-	} else {
+	} else if (old_model != BLK_ZONED_NONE) {
 		blk_queue_clear_zone_settings(q);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-stat.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-stat.c
@@ -28,7 +28,7 @@
 /* src is a per-cpu stat, mean isn't initialized */
 void blk_rq_stat_sum(struct blk_rq_stat *dst, struct blk_rq_stat *src)
 {
-	if (!src->nr_samples)
+	if (dst->nr_samples + src->nr_samples <= dst->nr_samples)
 		return;
 
 	dst->min = min(dst->min, src->min);
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-sysfs.c
@@ -748,6 +748,8 @@
 {
 	struct request_queue *q = container_of(rcu_head, struct request_queue,
 					       rcu_head);
+
+	percpu_ref_exit(&q->q_usage_counter);
 	kmem_cache_free(blk_requestq_cachep, q);
 }
 
@@ -805,16 +807,6 @@
 
 	blk_free_queue_stats(q->stats);
 
-	if (queue_is_mq(q)) {
-		struct blk_mq_hw_ctx *hctx;
-		int i;
-
-		cancel_delayed_work_sync(&q->requeue_work);
-
-		queue_for_each_hw_ctx(q, hctx, i)
-			cancel_delayed_work_sync(&hctx->run_work);
-	}
-
 	blk_exit_queue(q);
 
 	blk_queue_free_zone_bitmaps(q);
@@ -964,15 +956,17 @@
 	 */
 	if (queue_is_mq(q))
 		blk_mq_unregister_dev(disk_to_dev(disk), q);
-
-	kobject_uevent(&q->kobj, KOBJ_REMOVE);
-	kobject_del(&q->kobj);
 	blk_trace_remove_sysfs(disk_to_dev(disk));
 
 	mutex_lock(&q->sysfs_lock);
 	if (q->elevator)
 		elv_unregister_queue(q);
 	mutex_unlock(&q->sysfs_lock);
+
+	/* Now that we've deleted all child objects, we can delete the queue. */
+	kobject_uevent(&q->kobj, KOBJ_REMOVE);
+	kobject_del(&q->kobj);
+
 	mutex_unlock(&q->sysfs_dir_lock);
 
 	kobject_put(&disk_to_dev(disk)->kobj);
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-throttle.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-throttle.c
@@ -950,7 +950,7 @@
 				 u64 bps_limit, unsigned long *wait)
 {
 	bool rw = bio_data_dir(bio);
-	u64 bytes_allowed, extra_bytes, tmp;
+	u64 bytes_allowed, extra_bytes;
 	unsigned long jiffy_elapsed, jiffy_wait, jiffy_elapsed_rnd;
 	unsigned int bio_size = throtl_bio_data_size(bio);
 
@@ -967,10 +967,8 @@
 		jiffy_elapsed_rnd = tg->td->throtl_slice;
 
 	jiffy_elapsed_rnd = roundup(jiffy_elapsed_rnd, tg->td->throtl_slice);
-
-	tmp = bps_limit * jiffy_elapsed_rnd;
-	do_div(tmp, HZ);
-	bytes_allowed = tmp;
+	bytes_allowed = mul_u64_u64_div_u64(bps_limit, (u64)jiffy_elapsed_rnd,
+					    (u64)HZ);
 
 	if (tg->bytes_disp[rw] + bio_size <= bytes_allowed) {
 		if (wait)
@@ -1417,6 +1415,7 @@
 		   tg_bps_limit(tg, READ), tg_bps_limit(tg, WRITE),
 		   tg_iops_limit(tg, READ), tg_iops_limit(tg, WRITE));
 
+	rcu_read_lock();
 	/*
 	 * Update has_rules[] flags for the updated tg's subtree.  A tg is
 	 * considered to have rules if either the tg itself or any of its
@@ -1444,6 +1443,7 @@
 		this_tg->latency_target = max(this_tg->latency_target,
 				parent_tg->latency_target);
 	}
+	rcu_read_unlock();
 
 	/*
 	 * We're already holding queue_lock and know @tg is valid.  Let's
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-wbt.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-wbt.c
@@ -357,6 +357,9 @@
 	unsigned int inflight = wbt_inflight(rwb);
 	int status;
 
+	if (!rwb->rqos.q->disk)
+		return;
+
 	status = latency_exceeded(rwb, cb->stat);
 
 	trace_wbt_timer(rwb->rqos.q->disk->bdi, status, rqd->scale_step,
@@ -817,6 +820,7 @@
 {
 	struct rq_wb *rwb;
 	int i;
+	int ret;
 
 	rwb = kzalloc(sizeof(*rwb), GFP_KERNEL);
 	if (!rwb)
@@ -837,19 +841,26 @@
 	rwb->last_comp = rwb->last_issue = jiffies;
 	rwb->win_nsec = RWB_WINDOW_NSEC;
 	rwb->enable_state = WBT_STATE_ON_DEFAULT;
-	rwb->wc = 1;
+	rwb->wc = test_bit(QUEUE_FLAG_WC, &q->queue_flags);
 	rwb->rq_depth.default_depth = RWB_DEF_DEPTH;
+	rwb->min_lat_nsec = wbt_default_latency_nsec(q);
+
+	wbt_queue_depth_changed(&rwb->rqos);
 
 	/*
 	 * Assign rwb and add the stats callback.
 	 */
-	rq_qos_add(q, &rwb->rqos);
+	ret = rq_qos_add(q, &rwb->rqos);
+	if (ret)
+		goto err_free;
+
 	blk_stat_add_callback(q, rwb->cb);
 
-	rwb->min_lat_nsec = wbt_default_latency_nsec(q);
+	return 0;
 
-	wbt_queue_depth_changed(&rwb->rqos);
-	wbt_set_write_cache(q, test_bit(QUEUE_FLAG_WC, &q->queue_flags));
+err_free:
+	blk_stat_free_callback(rwb->cb);
+	kfree(rwb);
+	return ret;
 
-	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk-zoned.c
+++ linux-xilinx-zynqmp-5.15.0/block/blk-zoned.c
@@ -429,9 +429,10 @@
 		op = REQ_OP_ZONE_RESET;
 
 		/* Invalidate the page cache, including dirty pages. */
+		filemap_invalidate_lock(bdev->bd_inode->i_mapping);
 		ret = blkdev_truncate_zone_range(bdev, mode, &zrange);
 		if (ret)
-			return ret;
+			goto fail;
 		break;
 	case BLKOPENZONE:
 		op = REQ_OP_ZONE_OPEN;
@@ -449,15 +450,9 @@
 	ret = blkdev_zone_mgmt(bdev, op, zrange.sector, zrange.nr_sectors,
 			       GFP_KERNEL);
 
-	/*
-	 * Invalidate the page cache again for zone reset: writes can only be
-	 * direct for zoned devices so concurrent writes would not add any page
-	 * to the page cache after/during reset. The page cache may be filled
-	 * again due to concurrent reads though and dropping the pages for
-	 * these is fine.
-	 */
-	if (!ret && cmd == BLKRESETZONE)
-		ret = blkdev_truncate_zone_range(bdev, mode, &zrange);
+fail:
+	if (cmd == BLKRESETZONE)
+		filemap_invalidate_unlock(bdev->bd_inode->i_mapping);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/block/blk.h
+++ linux-xilinx-zynqmp-5.15.0/block/blk.h
@@ -130,8 +130,7 @@
 				bip_next->bip_vec[0].bv_offset);
 }
 
-int blk_integrity_add(struct gendisk *disk);
-void blk_integrity_del(struct gendisk *);
+extern const struct attribute_group blk_integrity_attr_group;
 #else /* CONFIG_BLK_DEV_INTEGRITY */
 static inline bool blk_integrity_merge_rq(struct request_queue *rq,
 		struct request *r1, struct request *r2)
@@ -164,13 +163,6 @@
 static inline void bio_integrity_free(struct bio *bio)
 {
 }
-static inline int blk_integrity_add(struct gendisk *disk)
-{
-	return 0;
-}
-static inline void blk_integrity_del(struct gendisk *disk)
-{
-}
 #endif /* CONFIG_BLK_DEV_INTEGRITY */
 
 unsigned long blk_rq_timeout(unsigned long timeout);
@@ -185,6 +177,12 @@
 void blk_account_io_done(struct request *req, u64 now);
 
 /*
+ * Plug flush limits
+ */
+#define BLK_MAX_REQUEST_COUNT	32
+#define BLK_PLUG_FLUSH_SIZE	(128 * 1024)
+
+/*
  * Internal elevator interface
  */
 #define ELV_ON_HASH(rq) ((rq)->rq_flags & RQF_HASHED)
--- linux-xilinx-zynqmp-5.15.0.orig/block/disk-events.c
+++ linux-xilinx-zynqmp-5.15.0/block/disk-events.c
@@ -307,6 +307,7 @@
 	if (!(events & DISK_EVENT_MEDIA_CHANGE))
 		return false;
 
+	inc_diskseq(disk);
 	if (__invalidate_device(disk->part0, true))
 		pr_warn("VFS: busy inodes on changed media %s\n",
 			disk->disk_name);
--- linux-xilinx-zynqmp-5.15.0.orig/block/elevator.c
+++ linux-xilinx-zynqmp-5.15.0/block/elevator.c
@@ -523,8 +523,6 @@
 		kobject_del(&e->kobj);
 
 		e->registered = 0;
-		/* Re-enable throttling in case elevator disabled it */
-		wbt_enable_default(q);
 	}
 }
 
@@ -622,7 +620,7 @@
 static inline bool elv_support_iosched(struct request_queue *q)
 {
 	if (!queue_is_mq(q) ||
-	    (q->tag_set && (q->tag_set->flags & BLK_MQ_F_NO_SCHED)))
+	    (q->tag_set->flags & BLK_MQ_F_NO_SCHED))
 		return false;
 	return true;
 }
@@ -633,7 +631,7 @@
  */
 static struct elevator_type *elevator_get_default(struct request_queue *q)
 {
-	if (q->tag_set && q->tag_set->flags & BLK_MQ_F_NO_SCHED_BY_DEFAULT)
+	if (q->tag_set->flags & BLK_MQ_F_NO_SCHED_BY_DEFAULT)
 		return NULL;
 
 	if (q->nr_hw_queues != 1 &&
@@ -694,12 +692,18 @@
 	if (!e)
 		return;
 
+	/*
+	 * We are called before adding disk, when there isn't any FS I/O,
+	 * so freezing queue plus canceling dispatch work is enough to
+	 * drain any dispatch activities originated from passthrough
+	 * requests, then no need to quiesce queue which may add long boot
+	 * latency, especially when lots of disks are involved.
+	 */
 	blk_mq_freeze_queue(q);
-	blk_mq_quiesce_queue(q);
+	blk_mq_cancel_work_sync(q);
 
 	err = blk_mq_init_sched(q, e);
 
-	blk_mq_unquiesce_queue(q);
 	blk_mq_unfreeze_queue(q);
 
 	if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/block/fops.c
+++ linux-xilinx-zynqmp-5.15.0/block/fops.c
@@ -243,6 +243,24 @@
 			bio_endio(bio);
 			break;
 		}
+		if (iocb->ki_flags & IOCB_NOWAIT) {
+			/*
+			 * This is nonblocking IO, and we need to allocate
+			 * another bio if we have data left to map. As we
+			 * cannot guarantee that one of the sub bios will not
+			 * fail getting issued FOR NOWAIT and as error results
+			 * are coalesced across all of them, be safe and ask for
+			 * a retry of this from blocking context.
+			 */
+			if (unlikely(iov_iter_count(iter))) {
+				bio_release_pages(bio, false);
+				bio_clear_flag(bio, BIO_REFFED);
+				bio_put(bio);
+				blk_finish_plug(&plug);
+				return -EAGAIN;
+			}
+			bio->bi_opf |= REQ_NOWAIT;
+		}
 
 		if (is_read) {
 			bio->bi_opf = REQ_OP_READ;
@@ -252,9 +270,6 @@
 			bio->bi_opf = dio_bio_write_op(iocb);
 			task_io_account_write(bio->bi_iter.bi_size);
 		}
-		if (iocb->ki_flags & IOCB_NOWAIT)
-			bio->bi_opf |= REQ_NOWAIT;
-
 		dio->size += bio->bi_iter.bi_size;
 		pos += bio->bi_iter.bi_size;
 
@@ -584,22 +599,33 @@
 
 	filemap_invalidate_lock(inode->i_mapping);
 
-	/* Invalidate the page cache, including dirty pages. */
-	error = truncate_bdev_range(bdev, file->f_mode, start, end);
-	if (error)
-		goto fail;
-
+	/*
+	 * Invalidate the page cache, including dirty pages, for valid
+	 * de-allocate mode calls to fallocate().
+	 */
 	switch (mode) {
 	case FALLOC_FL_ZERO_RANGE:
 	case FALLOC_FL_ZERO_RANGE | FALLOC_FL_KEEP_SIZE:
+		error = truncate_bdev_range(bdev, file->f_mode, start, end);
+		if (error)
+			goto fail;
+
 		error = blkdev_issue_zeroout(bdev, start >> 9, len >> 9,
 					    GFP_KERNEL, BLKDEV_ZERO_NOUNMAP);
 		break;
 	case FALLOC_FL_PUNCH_HOLE | FALLOC_FL_KEEP_SIZE:
+		error = truncate_bdev_range(bdev, file->f_mode, start, end);
+		if (error)
+			goto fail;
+
 		error = blkdev_issue_zeroout(bdev, start >> 9, len >> 9,
 					     GFP_KERNEL, BLKDEV_ZERO_NOFALLBACK);
 		break;
 	case FALLOC_FL_PUNCH_HOLE | FALLOC_FL_KEEP_SIZE | FALLOC_FL_NO_HIDE_STALE:
+		error = truncate_bdev_range(bdev, file->f_mode, start, end);
+		if (error)
+			goto fail;
+
 		error = blkdev_issue_discard(bdev, start >> 9, len >> 9,
 					     GFP_KERNEL, 0);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/block/genhd.c
+++ linux-xilinx-zynqmp-5.15.0/block/genhd.c
@@ -19,6 +19,7 @@
 #include <linux/seq_file.h>
 #include <linux/slab.h>
 #include <linux/kmod.h>
+#include <linux/major.h>
 #include <linux/mutex.h>
 #include <linux/idr.h>
 #include <linux/log2.h>
@@ -181,7 +182,9 @@
 	struct blk_major_name *next;
 	int major;
 	char name[16];
+#ifdef CONFIG_BLOCK_LEGACY_AUTOLOAD
 	void (*probe)(dev_t devt);
+#endif
 } *major_names[BLKDEV_MAJOR_HASH_SIZE];
 static DEFINE_MUTEX(major_names_lock);
 static DEFINE_SPINLOCK(major_names_spinlock);
@@ -268,7 +271,9 @@
 	}
 
 	p->major = major;
+#ifdef CONFIG_BLOCK_LEGACY_AUTOLOAD
 	p->probe = probe;
+#endif
 	strlcpy(p->name, name, sizeof(p->name));
 	p->next = NULL;
 	index = major_to_index(major);
@@ -323,7 +328,7 @@
 {
 	int idx;
 
-	idx = ida_alloc_range(&ext_devt_ida, 0, NR_EXT_DEVT, GFP_KERNEL);
+	idx = ida_alloc_range(&ext_devt_ida, 0, NR_EXT_DEVT - 1, GFP_KERNEL);
 	if (idx == -ENOSPC)
 		return -EBUSY;
 	return idx;
@@ -420,6 +425,10 @@
 				DISK_MAX_PARTS);
 			disk->minors = DISK_MAX_PARTS;
 		}
+		if (disk->first_minor > MINORMASK ||
+		    disk->minors > MINORMASK + 1 ||
+		    disk->first_minor + disk->minors > MINORMASK + 1)
+			return -EINVAL;
 	} else {
 		if (WARN_ON(disk->minors))
 			return -EINVAL;
@@ -432,10 +441,6 @@
 		disk->flags |= GENHD_FL_EXT_DEVT;
 	}
 
-	ret = disk_alloc_events(disk);
-	if (ret)
-		goto out_free_ext_minor;
-
 	/* delay uevents, until we scanned partition table */
 	dev_set_uevent_suppress(ddev, 1);
 
@@ -446,7 +451,12 @@
 		ddev->devt = MKDEV(disk->major, disk->first_minor);
 	ret = device_add(ddev);
 	if (ret)
-		goto out_disk_release_events;
+		goto out_free_ext_minor;
+
+	ret = disk_alloc_events(disk);
+	if (ret)
+		goto out_device_del;
+
 	if (!sysfs_deprecated) {
 		ret = sysfs_create_link(block_depr, &ddev->kobj,
 					kobject_name(&ddev->kobj));
@@ -461,17 +471,17 @@
 	 */
 	pm_runtime_set_memalloc_noio(ddev, true);
 
-	ret = blk_integrity_add(disk);
-	if (ret)
-		goto out_del_block_link;
-
 	disk->part0->bd_holder_dir =
 		kobject_create_and_add("holders", &ddev->kobj);
-	if (!disk->part0->bd_holder_dir)
-		goto out_del_integrity;
+	if (!disk->part0->bd_holder_dir) {
+		ret = -ENOMEM;
+		goto out_del_block_link;
+	}
 	disk->slave_dir = kobject_create_and_add("slaves", &ddev->kobj);
-	if (!disk->slave_dir)
+	if (!disk->slave_dir) {
+		ret = -ENOMEM;
 		goto out_put_holder_dir;
+	}
 
 	ret = bd_register_pending_holders(disk);
 	if (ret < 0)
@@ -487,7 +497,7 @@
 		 * and don't bother scanning for partitions either.
 		 */
 		disk->flags |= GENHD_FL_SUPPRESS_PARTITION_INFO;
-		disk->flags |= GENHD_FL_NO_PART_SCAN;
+		disk->flags |= GENHD_FL_NO_PART;
 	} else {
 		ret = bdi_register(disk->bdi, "%u:%u",
 				   disk->major, disk->first_minor);
@@ -519,19 +529,18 @@
 		bdi_unregister(disk->bdi);
 out_unregister_queue:
 	blk_unregister_queue(disk);
+	rq_qos_exit(disk->queue);
 out_put_slave_dir:
 	kobject_put(disk->slave_dir);
+	disk->slave_dir = NULL;
 out_put_holder_dir:
 	kobject_put(disk->part0->bd_holder_dir);
-out_del_integrity:
-	blk_integrity_del(disk);
 out_del_block_link:
 	if (!sysfs_deprecated)
 		sysfs_remove_link(block_depr, dev_name(ddev));
+	pm_runtime_set_memalloc_noio(ddev, false);
 out_device_del:
 	device_del(ddev);
-out_disk_release_events:
-	disk_release_events(disk);
 out_free_ext_minor:
 	if (disk->major == BLOCK_EXT_MAJOR)
 		blk_free_ext_minor(disk->first_minor);
@@ -540,6 +549,20 @@
 EXPORT_SYMBOL(device_add_disk);
 
 /**
+ * blk_mark_disk_dead - mark a disk as dead
+ * @disk: disk to mark as dead
+ *
+ * Mark as disk as dead (e.g. surprise removed) and don't accept any new I/O
+ * to this disk.
+ */
+void blk_mark_disk_dead(struct gendisk *disk)
+{
+	set_bit(GD_DEAD, &disk->state);
+	blk_queue_start_drain(disk->queue);
+}
+EXPORT_SYMBOL_GPL(blk_mark_disk_dead);
+
+/**
  * del_gendisk - remove the gendisk
  * @disk: the struct gendisk to remove
  *
@@ -567,7 +590,6 @@
 	if (WARN_ON_ONCE(!disk_live(disk) && !(disk->flags & GENHD_FL_HIDDEN)))
 		return;
 
-	blk_integrity_del(disk);
 	disk_del_events(disk);
 
 	mutex_lock(&disk->open_mutex);
@@ -603,6 +625,7 @@
 
 	kobject_put(disk->part0->bd_holder_dir);
 	kobject_put(disk->slave_dir);
+	disk->slave_dir = NULL;
 
 	part_stat_set_all(disk->part0, 0);
 	disk->part0->bd_stamp = 0;
@@ -650,7 +673,8 @@
 	return badblocks_store(disk->bb, page, len, 0);
 }
 
-void blk_request_module(dev_t devt)
+#ifdef CONFIG_BLOCK_LEGACY_AUTOLOAD
+static bool blk_probe_dev(dev_t devt)
 {
 	unsigned int major = MAJOR(devt);
 	struct blk_major_name **n;
@@ -660,15 +684,28 @@
 		if ((*n)->major == major && (*n)->probe) {
 			(*n)->probe(devt);
 			mutex_unlock(&major_names_lock);
-			return;
+			return true;
 		}
 	}
 	mutex_unlock(&major_names_lock);
+	return false;
+}
+
+void blk_request_module(dev_t devt)
+{
+	int error;
 
-	if (request_module("block-major-%d-%d", MAJOR(devt), MINOR(devt)) > 0)
-		/* Make old-style 2.4 aliases work */
-		request_module("block-major-%d", MAJOR(devt));
+	if (blk_probe_dev(devt))
+		return;
+
+	error = request_module("block-major-%d-%d", MAJOR(devt), MINOR(devt));
+	/* Make old-style 2.4 aliases work */
+	if (error > 0)
+		error = request_module("block-major-%d", MAJOR(devt));
+	if (!error)
+		blk_probe_dev(devt);
 }
+#endif /* CONFIG_BLOCK_LEGACY_AUTOLOAD */
 
 /*
  * print a full list of all partitions - intended for places where the root
@@ -1058,6 +1095,9 @@
 
 static const struct attribute_group *disk_attr_groups[] = {
 	&disk_attr_group,
+#ifdef CONFIG_BLK_DEV_INTEGRITY
+	&blk_integrity_attr_group,
+#endif
 	NULL
 };
 
@@ -1082,6 +1122,8 @@
 	might_sleep();
 	WARN_ON_ONCE(disk_live(disk));
 
+	blk_mq_cancel_work_sync(disk->queue);
+
 	disk_release_events(disk);
 	kfree(disk->random);
 	xa_destroy(&disk->part_tbl);
--- linux-xilinx-zynqmp-5.15.0.orig/block/holder.c
+++ linux-xilinx-zynqmp-5.15.0/block/holder.c
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 #include <linux/genhd.h>
+#include <linux/slab.h>
 
 struct bd_holder_disk {
 	struct list_head	list;
--- linux-xilinx-zynqmp-5.15.0.orig/block/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/block/ioctl.c
@@ -18,7 +18,7 @@
 {
 	struct gendisk *disk = bdev->bd_disk;
 	struct blkpg_partition p;
-	long long start, length;
+	sector_t start, length;
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EACCES;
@@ -33,14 +33,17 @@
 	if (op == BLKPG_DEL_PARTITION)
 		return bdev_del_partition(disk, p.pno);
 
+	if (p.start < 0 || p.length <= 0 || LLONG_MAX - p.length < p.start)
+		return -EINVAL;
+	/* Check that the partition is aligned to the block size */
+	if (!IS_ALIGNED(p.start | p.length, bdev_logical_block_size(bdev)))
+		return -EINVAL;
+
 	start = p.start >> SECTOR_SHIFT;
 	length = p.length >> SECTOR_SHIFT;
 
 	switch (op) {
 	case BLKPG_ADD_PARTITION:
-		/* check if partition is aligned to blocksize */
-		if (p.start & (bdev_logical_block_size(bdev) - 1))
-			return -EINVAL;
 		return bdev_add_partition(disk, p.pno, start, length);
 	case BLKPG_RESIZE_PARTITION:
 		return bdev_resize_partition(disk, p.pno, start, length);
@@ -113,6 +116,7 @@
 	uint64_t range[2];
 	uint64_t start, len;
 	struct request_queue *q = bdev_get_queue(bdev);
+	struct inode *inode = bdev->bd_inode;
 	int err;
 
 	if (!(mode & FMODE_WRITE))
@@ -135,12 +139,17 @@
 	if (start + len > i_size_read(bdev->bd_inode))
 		return -EINVAL;
 
+	filemap_invalidate_lock(inode->i_mapping);
 	err = truncate_bdev_range(bdev, mode, start, start + len - 1);
 	if (err)
-		return err;
+		goto fail;
 
-	return blkdev_issue_discard(bdev, start >> 9, len >> 9,
-				    GFP_KERNEL, flags);
+	err = blkdev_issue_discard(bdev, start >> 9, len >> 9,
+				   GFP_KERNEL, flags);
+
+fail:
+	filemap_invalidate_unlock(inode->i_mapping);
+	return err;
 }
 
 static int blk_ioctl_zeroout(struct block_device *bdev, fmode_t mode,
@@ -148,6 +157,7 @@
 {
 	uint64_t range[2];
 	uint64_t start, end, len;
+	struct inode *inode = bdev->bd_inode;
 	int err;
 
 	if (!(mode & FMODE_WRITE))
@@ -170,12 +180,17 @@
 		return -EINVAL;
 
 	/* Invalidate the page cache, including dirty pages */
+	filemap_invalidate_lock(inode->i_mapping);
 	err = truncate_bdev_range(bdev, mode, start, end);
 	if (err)
-		return err;
+		goto fail;
+
+	err = blkdev_issue_zeroout(bdev, start >> 9, len >> 9, GFP_KERNEL,
+				   BLKDEV_ZERO_NOUNMAP);
 
-	return blkdev_issue_zeroout(bdev, start >> 9, len >> 9, GFP_KERNEL,
-			BLKDEV_ZERO_NOUNMAP);
+fail:
+	filemap_invalidate_unlock(inode->i_mapping);
+	return err;
 }
 
 static int put_ushort(unsigned short __user *argp, unsigned short val)
@@ -633,7 +648,7 @@
 			(bdev->bd_disk->bdi->ra_pages * PAGE_SIZE) / 512);
 	case BLKGETSIZE:
 		size = i_size_read(bdev->bd_inode);
-		if ((size >> 9) > ~0UL)
+		if ((size >> 9) > ~(compat_ulong_t)0)
 			return -EFBIG;
 		return compat_put_ulong(argp, size >> 9);
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/ioprio.c
+++ linux-xilinx-zynqmp-5.15.0/block/ioprio.c
@@ -69,7 +69,14 @@
 
 	switch (class) {
 		case IOPRIO_CLASS_RT:
-			if (!capable(CAP_SYS_NICE) && !capable(CAP_SYS_ADMIN))
+			/*
+			 * Originally this only checked for CAP_SYS_ADMIN,
+			 * which was implicitly allowed for pid 0 by security
+			 * modules such as SELinux. Make sure we check
+			 * CAP_SYS_ADMIN first to avoid a denial/avc for
+			 * possibly missing CAP_SYS_NICE permission.
+			 */
+			if (!capable(CAP_SYS_ADMIN) && !capable(CAP_SYS_NICE))
 				return -EPERM;
 			fallthrough;
 			/* rt has prio field too */
@@ -182,9 +189,9 @@
 int ioprio_best(unsigned short aprio, unsigned short bprio)
 {
 	if (!ioprio_valid(aprio))
-		aprio = IOPRIO_DEFAULT;
+		aprio = IOPRIO_PRIO_VALUE(IOPRIO_CLASS_BE, IOPRIO_BE_NORM);
 	if (!ioprio_valid(bprio))
-		bprio = IOPRIO_DEFAULT;
+		bprio = IOPRIO_PRIO_VALUE(IOPRIO_CLASS_BE, IOPRIO_BE_NORM);
 
 	return min(aprio, bprio);
 }
@@ -213,6 +220,7 @@
 				pgrp = task_pgrp(current);
 			else
 				pgrp = find_vpid(who);
+			read_lock(&tasklist_lock);
 			do_each_pid_thread(pgrp, PIDTYPE_PGID, p) {
 				tmpio = get_task_ioprio(p);
 				if (tmpio < 0)
@@ -222,6 +230,8 @@
 				else
 					ret = ioprio_best(ret, tmpio);
 			} while_each_pid_thread(pgrp, PIDTYPE_PGID, p);
+			read_unlock(&tasklist_lock);
+
 			break;
 		case IOPRIO_WHO_USER:
 			uid = make_kuid(current_user_ns(), who);
--- linux-xilinx-zynqmp-5.15.0.orig/block/keyslot-manager.c
+++ linux-xilinx-zynqmp-5.15.0/block/keyslot-manager.c
@@ -343,25 +343,16 @@
 	return true;
 }
 
-/**
- * blk_ksm_evict_key() - Evict a key from the lower layer device.
- * @ksm: The keyslot manager to evict from
- * @key: The key to evict
- *
- * Find the keyslot that the specified key was programmed into, and evict that
- * slot from the lower layer device. The slot must not be in use by any
- * in-flight IO when this function is called.
- *
- * Context: Process context. Takes and releases ksm->lock.
- * Return: 0 on success or if there's no keyslot with the specified key, -EBUSY
- *	   if the keyslot is still in use, or another -errno value on other
- *	   error.
+/*
+ * This is an internal function that evicts a key from an inline encryption
+ * device that can be either a real device or the blk-crypto-fallback "device".
+ * It is used only by blk_crypto_evict_key(); see that function for details.
  */
 int blk_ksm_evict_key(struct blk_keyslot_manager *ksm,
 		      const struct blk_crypto_key *key)
 {
 	struct blk_ksm_keyslot *slot;
-	int err = 0;
+	int err;
 
 	if (blk_ksm_is_passthrough(ksm)) {
 		if (ksm->ksm_ll_ops.keyslot_evict) {
@@ -375,22 +366,30 @@
 
 	blk_ksm_hw_enter(ksm);
 	slot = blk_ksm_find_keyslot(ksm, key);
-	if (!slot)
-		goto out_unlock;
+	if (!slot) {
+		/*
+		 * Not an error, since a key not in use by I/O is not guaranteed
+		 * to be in a keyslot.  There can be more keys than keyslots.
+		 */
+		err = 0;
+		goto out;
+	}
 
 	if (WARN_ON_ONCE(atomic_read(&slot->slot_refs) != 0)) {
+		/* BUG: key is still in use by I/O */
 		err = -EBUSY;
-		goto out_unlock;
+		goto out_remove;
 	}
 	err = ksm->ksm_ll_ops.keyslot_evict(ksm, key,
 					    blk_ksm_get_slot_idx(slot));
-	if (err)
-		goto out_unlock;
-
+out_remove:
+	/*
+	 * Callers free the key even on error, so unlink the key from the hash
+	 * table and clear slot->key even on error.
+	 */
 	hlist_del(&slot->hash_node);
 	slot->key = NULL;
-	err = 0;
-out_unlock:
+out:
 	blk_ksm_hw_exit(ksm);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/block/mq-deadline.c
+++ linux-xilinx-zynqmp-5.15.0/block/mq-deadline.c
@@ -154,6 +154,20 @@
 }
 
 /*
+ * get the request before `rq' in sector-sorted order
+ */
+static inline struct request *
+deadline_earlier_request(struct request *rq)
+{
+	struct rb_node *node = rb_prev(&rq->rb_node);
+
+	if (node)
+		return rb_entry_rq(node);
+
+	return NULL;
+}
+
+/*
  * get the request after `rq' in sector-sorted order
  */
 static inline struct request *
@@ -289,6 +303,39 @@
 }
 
 /*
+ * Check if rq has a sequential request preceding it.
+ */
+static bool deadline_is_seq_write(struct deadline_data *dd, struct request *rq)
+{
+	struct request *prev = deadline_earlier_request(rq);
+
+	if (!prev)
+		return false;
+
+	return blk_rq_pos(prev) + blk_rq_sectors(prev) == blk_rq_pos(rq);
+}
+
+/*
+ * Skip all write requests that are sequential from @rq, even if we cross
+ * a zone boundary.
+ */
+static struct request *deadline_skip_seq_writes(struct deadline_data *dd,
+						struct request *rq)
+{
+	sector_t pos = blk_rq_pos(rq);
+	sector_t skipped_sectors = 0;
+
+	while (rq) {
+		if (blk_rq_pos(rq) != pos + skipped_sectors)
+			break;
+		skipped_sectors += blk_rq_sectors(rq);
+		rq = deadline_latter_request(rq);
+	}
+
+	return rq;
+}
+
+/*
  * For the specified data direction, return the next request to
  * dispatch using arrival ordered lists.
  */
@@ -308,11 +355,16 @@
 
 	/*
 	 * Look for a write request that can be dispatched, that is one with
-	 * an unlocked target zone.
+	 * an unlocked target zone. For some HDDs, breaking a sequential
+	 * write stream can lead to lower throughput, so make sure to preserve
+	 * sequential write streams, even if that stream crosses into the next
+	 * zones and these zones are unlocked.
 	 */
 	spin_lock_irqsave(&dd->zone_lock, flags);
 	list_for_each_entry(rq, &per_prio->fifo_list[DD_WRITE], queuelist) {
-		if (blk_req_can_dispatch_to_zone(rq))
+		if (blk_req_can_dispatch_to_zone(rq) &&
+		    (blk_queue_nonrot(rq->q) ||
+		     !deadline_is_seq_write(dd, rq)))
 			goto out;
 	}
 	rq = NULL;
@@ -342,13 +394,19 @@
 
 	/*
 	 * Look for a write request that can be dispatched, that is one with
-	 * an unlocked target zone.
+	 * an unlocked target zone. For some HDDs, breaking a sequential
+	 * write stream can lead to lower throughput, so make sure to preserve
+	 * sequential write streams, even if that stream crosses into the next
+	 * zones and these zones are unlocked.
 	 */
 	spin_lock_irqsave(&dd->zone_lock, flags);
 	while (rq) {
 		if (blk_req_can_dispatch_to_zone(rq))
 			break;
-		rq = deadline_latter_request(rq);
+		if (blk_queue_nonrot(rq->q))
+			rq = deadline_latter_request(rq);
+		else
+			rq = deadline_skip_seq_writes(dd, rq);
 	}
 	spin_unlock_irqrestore(&dd->zone_lock, flags);
 
@@ -733,6 +791,18 @@
 	rq->elv.priv[0] = NULL;
 }
 
+static bool dd_has_write_work(struct blk_mq_hw_ctx *hctx)
+{
+	struct deadline_data *dd = hctx->queue->elevator->elevator_data;
+	enum dd_prio p;
+
+	for (p = 0; p <= DD_PRIO_MAX; p++)
+		if (!list_empty_careful(&dd->per_prio[p].fifo_list[DD_WRITE]))
+			return true;
+
+	return false;
+}
+
 /*
  * Callback from inside blk_mq_free_request().
  *
@@ -755,7 +825,6 @@
 	struct deadline_data *dd = q->elevator->elevator_data;
 	const u8 ioprio_class = dd_rq_ioclass(rq);
 	const enum dd_prio prio = ioprio_class_to_prio[ioprio_class];
-	struct dd_per_prio *per_prio = &dd->per_prio[prio];
 
 	/*
 	 * The block layer core may call dd_finish_request() without having
@@ -771,9 +840,10 @@
 
 		spin_lock_irqsave(&dd->zone_lock, flags);
 		blk_req_zone_write_unlock(rq);
-		if (!list_empty(&per_prio->fifo_list[DD_WRITE]))
-			blk_mq_sched_mark_restart_hctx(rq->mq_hctx);
 		spin_unlock_irqrestore(&dd->zone_lock, flags);
+
+		if (dd_has_write_work(rq->mq_hctx))
+			blk_mq_sched_mark_restart_hctx(rq->mq_hctx);
 	}
 }
 
@@ -811,7 +881,7 @@
 SHOW_JIFFIES(deadline_write_expire_show, dd->fifo_expire[DD_WRITE]);
 SHOW_INT(deadline_writes_starved_show, dd->writes_starved);
 SHOW_INT(deadline_front_merges_show, dd->front_merges);
-SHOW_INT(deadline_async_depth_show, dd->front_merges);
+SHOW_INT(deadline_async_depth_show, dd->async_depth);
 SHOW_INT(deadline_fifo_batch_show, dd->fifo_batch);
 #undef SHOW_INT
 #undef SHOW_JIFFIES
@@ -840,7 +910,7 @@
 STORE_JIFFIES(deadline_write_expire_store, &dd->fifo_expire[DD_WRITE], 0, INT_MAX);
 STORE_INT(deadline_writes_starved_store, &dd->writes_starved, INT_MIN, INT_MAX);
 STORE_INT(deadline_front_merges_store, &dd->front_merges, 0, 1);
-STORE_INT(deadline_async_depth_store, &dd->front_merges, 1, INT_MAX);
+STORE_INT(deadline_async_depth_store, &dd->async_depth, 1, INT_MAX);
 STORE_INT(deadline_fifo_batch_store, &dd->fifo_batch, 0, INT_MAX);
 #undef STORE_FUNCTION
 #undef STORE_INT
--- linux-xilinx-zynqmp-5.15.0.orig/block/opal_proto.h
+++ linux-xilinx-zynqmp-5.15.0/block/opal_proto.h
@@ -66,6 +66,7 @@
 #define SHORT_ATOM_BYTE  0xBF
 #define MEDIUM_ATOM_BYTE 0xDF
 #define LONG_ATOM_BYTE   0xE3
+#define EMPTY_ATOM_BYTE  0xFF
 
 #define OPAL_INVAL_PARAM 12
 #define OPAL_MANUFACTURED_INACTIVE 0x08
--- linux-xilinx-zynqmp-5.15.0.orig/block/partitions/amiga.c
+++ linux-xilinx-zynqmp-5.15.0/block/partitions/amiga.c
@@ -11,10 +11,18 @@
 #define pr_fmt(fmt) fmt
 
 #include <linux/types.h>
+#include <linux/mm_types.h>
+#include <linux/overflow.h>
 #include <linux/affs_hardblocks.h>
 
 #include "check.h"
 
+/* magic offsets in partition DosEnvVec */
+#define NR_HD	3
+#define NR_SECT	5
+#define LO_CYL	9
+#define HI_CYL	10
+
 static __inline__ u32
 checksum_block(__be32 *m, int size)
 {
@@ -31,8 +39,12 @@
 	unsigned char *data;
 	struct RigidDiskBlock *rdb;
 	struct PartitionBlock *pb;
-	int start_sect, nr_sects, blk, part, res = 0;
-	int blksize = 1;	/* Multiplier for disk block size */
+	u64 start_sect, nr_sects;
+	sector_t blk, end_sect;
+	u32 cylblk;		/* rdb_CylBlocks = nr_heads*sect_per_track */
+	u32 nr_hd, nr_sect, lo_cyl, hi_cyl;
+	int part, res = 0;
+	unsigned int blksize = 1;	/* Multiplier for disk block size */
 	int slot = 1;
 
 	for (blk = 0; ; blk++, put_dev_sector(sect)) {
@@ -40,7 +52,7 @@
 			goto rdb_done;
 		data = read_part_sector(state, blk, &sect);
 		if (!data) {
-			pr_err("Dev %s: unable to read RDB block %d\n",
+			pr_err("Dev %s: unable to read RDB block %llu\n",
 			       state->disk->disk_name, blk);
 			res = -1;
 			goto rdb_done;
@@ -57,12 +69,12 @@
 		*(__be32 *)(data+0xdc) = 0;
 		if (checksum_block((__be32 *)data,
 				be32_to_cpu(rdb->rdb_SummedLongs) & 0x7F)==0) {
-			pr_err("Trashed word at 0xd0 in block %d ignored in checksum calculation\n",
+			pr_err("Trashed word at 0xd0 in block %llu ignored in checksum calculation\n",
 			       blk);
 			break;
 		}
 
-		pr_err("Dev %s: RDB in block %d has bad checksum\n",
+		pr_err("Dev %s: RDB in block %llu has bad checksum\n",
 		       state->disk->disk_name, blk);
 	}
 
@@ -78,11 +90,16 @@
 	}
 	blk = be32_to_cpu(rdb->rdb_PartitionList);
 	put_dev_sector(sect);
-	for (part = 1; blk>0 && part<=16; part++, put_dev_sector(sect)) {
-		blk *= blksize;	/* Read in terms partition table understands */
+	for (part = 1; (s32) blk>0 && part<=16; part++, put_dev_sector(sect)) {
+		/* Read in terms partition table understands */
+		if (check_mul_overflow(blk, (sector_t) blksize, &blk)) {
+			pr_err("Dev %s: overflow calculating partition block %llu! Skipping partitions %u and beyond\n",
+				state->disk->disk_name, blk, part);
+			break;
+		}
 		data = read_part_sector(state, blk, &sect);
 		if (!data) {
-			pr_err("Dev %s: unable to read partition block %d\n",
+			pr_err("Dev %s: unable to read partition block %llu\n",
 			       state->disk->disk_name, blk);
 			res = -1;
 			goto rdb_done;
@@ -94,19 +111,70 @@
 		if (checksum_block((__be32 *)pb, be32_to_cpu(pb->pb_SummedLongs) & 0x7F) != 0 )
 			continue;
 
-		/* Tell Kernel about it */
+		/* RDB gives us more than enough rope to hang ourselves with,
+		 * many times over (2^128 bytes if all fields max out).
+		 * Some careful checks are in order, so check for potential
+		 * overflows.
+		 * We are multiplying four 32 bit numbers to one sector_t!
+		 */
+
+		nr_hd   = be32_to_cpu(pb->pb_Environment[NR_HD]);
+		nr_sect = be32_to_cpu(pb->pb_Environment[NR_SECT]);
+
+		/* CylBlocks is total number of blocks per cylinder */
+		if (check_mul_overflow(nr_hd, nr_sect, &cylblk)) {
+			pr_err("Dev %s: heads*sects %u overflows u32, skipping partition!\n",
+				state->disk->disk_name, cylblk);
+			continue;
+		}
+
+		/* check for consistency with RDB defined CylBlocks */
+		if (cylblk > be32_to_cpu(rdb->rdb_CylBlocks)) {
+			pr_warn("Dev %s: cylblk %u > rdb_CylBlocks %u!\n",
+				state->disk->disk_name, cylblk,
+				be32_to_cpu(rdb->rdb_CylBlocks));
+		}
+
+		/* RDB allows for variable logical block size -
+		 * normalize to 512 byte blocks and check result.
+		 */
+
+		if (check_mul_overflow(cylblk, blksize, &cylblk)) {
+			pr_err("Dev %s: partition %u bytes per cyl. overflows u32, skipping partition!\n",
+				state->disk->disk_name, part);
+			continue;
+		}
+
+		/* Calculate partition start and end. Limit of 32 bit on cylblk
+		 * guarantees no overflow occurs if LBD support is enabled.
+		 */
+
+		lo_cyl = be32_to_cpu(pb->pb_Environment[LO_CYL]);
+		start_sect = ((u64) lo_cyl * cylblk);
+
+		hi_cyl = be32_to_cpu(pb->pb_Environment[HI_CYL]);
+		nr_sects = (((u64) hi_cyl - lo_cyl + 1) * cylblk);
 
-		nr_sects = (be32_to_cpu(pb->pb_Environment[10]) + 1 -
-			    be32_to_cpu(pb->pb_Environment[9])) *
-			   be32_to_cpu(pb->pb_Environment[3]) *
-			   be32_to_cpu(pb->pb_Environment[5]) *
-			   blksize;
 		if (!nr_sects)
 			continue;
-		start_sect = be32_to_cpu(pb->pb_Environment[9]) *
-			     be32_to_cpu(pb->pb_Environment[3]) *
-			     be32_to_cpu(pb->pb_Environment[5]) *
-			     blksize;
+
+		/* Warn user if partition end overflows u32 (AmigaDOS limit) */
+
+		if ((start_sect + nr_sects) > UINT_MAX) {
+			pr_warn("Dev %s: partition %u (%llu-%llu) needs 64 bit device support!\n",
+				state->disk->disk_name, part,
+				start_sect, start_sect + nr_sects);
+		}
+
+		if (check_add_overflow(start_sect, nr_sects, &end_sect)) {
+			pr_err("Dev %s: partition %u (%llu-%llu) needs LBD device support, skipping partition!\n",
+				state->disk->disk_name, part,
+				start_sect, end_sect);
+			continue;
+		}
+
+		/* Tell Kernel about it */
+
 		put_partition(state,slot++,start_sect,nr_sects);
 		{
 			/* Be even more informative to aid mounting */
--- linux-xilinx-zynqmp-5.15.0.orig/block/partitions/core.c
+++ linux-xilinx-zynqmp-5.15.0/block/partitions/core.c
@@ -5,6 +5,7 @@
  * Copyright (C) 2020 Christoph Hellwig
  */
 #include <linux/fs.h>
+#include <linux/major.h>
 #include <linux/slab.h>
 #include <linux/ctype.h>
 #include <linux/genhd.h>
@@ -462,6 +463,11 @@
 		goto out;
 	}
 
+	if (disk->flags & GENHD_FL_NO_PART) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	if (partition_overlaps(disk, start, length, -1)) {
 		ret = -EBUSY;
 		goto out;
@@ -525,18 +531,15 @@
 
 static bool disk_unlock_native_capacity(struct gendisk *disk)
 {
-	const struct block_device_operations *bdops = disk->fops;
-
-	if (bdops->unlock_native_capacity &&
-	    !(disk->flags & GENHD_FL_NATIVE_CAPACITY)) {
-		printk(KERN_CONT "enabling native capacity\n");
-		bdops->unlock_native_capacity(disk);
-		disk->flags |= GENHD_FL_NATIVE_CAPACITY;
-		return true;
-	} else {
+	if (!disk->fops->unlock_native_capacity ||
+	    test_and_set_bit(GD_NATIVE_CAPACITY, &disk->state)) {
 		printk(KERN_CONT "truncated\n");
 		return false;
 	}
+
+	printk(KERN_CONT "enabling native capacity\n");
+	disk->fops->unlock_native_capacity(disk);
+	return true;
 }
 
 void blk_drop_partitions(struct gendisk *disk)
@@ -587,9 +590,11 @@
 
 	part = add_partition(disk, p, from, size, state->parts[p].flags,
 			     &state->parts[p].info);
-	if (IS_ERR(part) && PTR_ERR(part) != -ENXIO) {
-		printk(KERN_ERR " %s: p%d could not be added: %ld\n",
-		       disk->disk_name, p, -PTR_ERR(part));
+	if (IS_ERR(part)) {
+		if (PTR_ERR(part) != -ENXIO) {
+			printk(KERN_ERR " %s: p%d could not be added: %pe\n",
+			       disk->disk_name, p, part);
+		}
 		return true;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/block/partitions/efi.c
+++ linux-xilinx-zynqmp-5.15.0/block/partitions/efi.c
@@ -682,7 +682,7 @@
 	out[size] = 0;
 
 	while (i < size) {
-		u8 c = le16_to_cpu(in[i]) & 0xff;
+		u8 c = le16_to_cpu(in[i]) & 0x7f;
 
 		if (c && !isprint(c))
 			c = '!';
--- linux-xilinx-zynqmp-5.15.0.orig/block/partitions/ldm.h
+++ linux-xilinx-zynqmp-5.15.0/block/partitions/ldm.h
@@ -1,5 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
-/**
+/*
  * ldm - Part of the Linux-NTFS project.
  *
  * Copyright (C) 2001,2002 Richard Russon <ldm@flatcap.org>
--- linux-xilinx-zynqmp-5.15.0.orig/block/partitions/mac.c
+++ linux-xilinx-zynqmp-5.15.0/block/partitions/mac.c
@@ -51,13 +51,25 @@
 	}
 	secsize = be16_to_cpu(md->block_size);
 	put_dev_sector(sect);
+
+	/*
+	 * If the "block size" is not a power of 2, things get weird - we might
+	 * end up with a partition straddling a sector boundary, so we wouldn't
+	 * be able to read a partition entry with read_part_sector().
+	 * Real block sizes are probably (?) powers of two, so just require
+	 * that.
+	 */
+	if (!is_power_of_2(secsize))
+		return -1;
 	datasize = round_down(secsize, 512);
 	data = read_part_sector(state, datasize / 512, &sect);
 	if (!data)
 		return -1;
 	partoffset = secsize % 512;
-	if (partoffset + sizeof(*part) > datasize)
+	if (partoffset + sizeof(*part) > datasize) {
+		put_dev_sector(sect);
 		return -1;
+	}
 	part = (struct mac_partition *) (data + partoffset);
 	if (be16_to_cpu(part->signature) != MAC_PARTITION_MAGIC) {
 		put_dev_sector(sect);
@@ -110,8 +122,8 @@
 				int i, l;
 
 				goodness++;
-				l = strlen(part->name);
-				if (strcmp(part->name, "/") == 0)
+				l = strnlen(part->name, sizeof(part->name));
+				if (strncmp(part->name, "/", sizeof(part->name)) == 0)
 					goodness++;
 				for (i = 0; i <= l - 4; ++i) {
 					if (strncasecmp(part->name + i, "root",
--- linux-xilinx-zynqmp-5.15.0.orig/block/sed-opal.c
+++ linux-xilinx-zynqmp-5.15.0/block/sed-opal.c
@@ -88,8 +88,8 @@
 	u64 lowest_lba;
 
 	size_t pos;
-	u8 cmd[IO_BUFFER_LENGTH];
-	u8 resp[IO_BUFFER_LENGTH];
+	u8 *cmd;
+	u8 *resp;
 
 	struct parsed_resp parsed;
 	size_t prev_d_len;
@@ -895,16 +895,20 @@
 			token_length = response_parse_medium(iter, pos);
 		else if (pos[0] <= LONG_ATOM_BYTE) /* long atom */
 			token_length = response_parse_long(iter, pos);
+		else if (pos[0] == EMPTY_ATOM_BYTE) /* empty atom */
+			token_length = 1;
 		else /* TOKEN */
 			token_length = response_parse_token(iter, pos);
 
 		if (token_length < 0)
 			return token_length;
 
+		if (pos[0] != EMPTY_ATOM_BYTE)
+			num_entries++;
+
 		pos += token_length;
 		total -= token_length;
 		iter++;
-		num_entries++;
 	}
 
 	resp->num = num_entries;
@@ -2134,6 +2138,8 @@
 		return;
 
 	clean_opal_dev(dev);
+	kfree(dev->resp);
+	kfree(dev->cmd);
 	kfree(dev);
 }
 EXPORT_SYMBOL(free_opal_dev);
@@ -2146,17 +2152,39 @@
 	if (!dev)
 		return NULL;
 
+	/*
+	 * Presumably DMA-able buffers must be cache-aligned. Kmalloc makes
+	 * sure the allocated buffer is DMA-safe in that regard.
+	 */
+	dev->cmd = kmalloc(IO_BUFFER_LENGTH, GFP_KERNEL);
+	if (!dev->cmd)
+		goto err_free_dev;
+
+	dev->resp = kmalloc(IO_BUFFER_LENGTH, GFP_KERNEL);
+	if (!dev->resp)
+		goto err_free_cmd;
+
 	INIT_LIST_HEAD(&dev->unlk_lst);
 	mutex_init(&dev->dev_lock);
 	dev->data = data;
 	dev->send_recv = send_recv;
 	if (check_opal_support(dev) != 0) {
 		pr_debug("Opal is not supported on this device\n");
-		kfree(dev);
-		return NULL;
+		goto err_free_resp;
 	}
 
 	return dev;
+
+err_free_resp:
+	kfree(dev->resp);
+
+err_free_cmd:
+	kfree(dev->cmd);
+
+err_free_dev:
+	kfree(dev);
+
+	return NULL;
 }
 EXPORT_SYMBOL(init_opal_dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/certs/blacklist.c
+++ linux-xilinx-zynqmp-5.15.0/certs/blacklist.c
@@ -172,6 +172,9 @@
 	if (IS_ERR(key)) {
 		pr_err("Problem with revocation key (%ld)\n", PTR_ERR(key));
 		return PTR_ERR(key);
+	} else {
+		pr_notice("Revoked X.509 cert '%s'\n",
+			  key_ref_to_ptr(key)->description);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/certs/blacklist_hashes.c
+++ linux-xilinx-zynqmp-5.15.0/certs/blacklist_hashes.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "blacklist.h"
 
-const char __initdata *const blacklist_hashes[] = {
+const char __initconst *const blacklist_hashes[] = {
 #include CONFIG_SYSTEM_BLACKLIST_HASH_LIST
 	, NULL
 };
--- linux-xilinx-zynqmp-5.15.0.orig/certs/common.c
+++ linux-xilinx-zynqmp-5.15.0/certs/common.c
@@ -41,6 +41,7 @@
 		if (IS_ERR(key)) {
 			pr_err("Problem loading in-kernel X.509 certificate (%ld)\n",
 			       PTR_ERR(key));
+			WARN_ON_ONCE(1);
 		} else {
 			pr_notice("Loaded X.509 cert '%s'\n",
 				  key_ref_to_ptr(key)->description);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/crypto/Kconfig
@@ -15,6 +15,7 @@
 #
 menuconfig CRYPTO
 	tristate "Cryptographic API"
+	select LIB_MEMNEQ
 	help
 	  This option provides the core Cryptographic API.
 
@@ -233,12 +234,12 @@
 
 config CRYPTO_ECC
 	tristate
+	select CRYPTO_RNG_DEFAULT
 
 config CRYPTO_ECDH
 	tristate "ECDH algorithm"
 	select CRYPTO_ECC
 	select CRYPTO_KPP
-	select CRYPTO_RNG_DEFAULT
 	help
 	  Generic implementation of the ECDH algorithm
 
@@ -683,26 +684,8 @@
 
 	  See https://blake2.net for further information.
 
-config CRYPTO_BLAKE2S
-	tristate "BLAKE2s digest algorithm"
-	select CRYPTO_LIB_BLAKE2S_GENERIC
-	select CRYPTO_HASH
-	help
-	  Implementation of cryptographic hash function BLAKE2s
-	  optimized for 8-32bit platforms and can produce digests of any size
-	  between 1 to 32.  The keyed hash is also implemented.
-
-	  This module provides the following algorithms:
-
-	  - blake2s-128
-	  - blake2s-160
-	  - blake2s-224
-	  - blake2s-256
-
-	  See https://blake2.net for further information.
-
 config CRYPTO_BLAKE2S_X86
-	tristate "BLAKE2s digest algorithm (x86 accelerated version)"
+	bool "BLAKE2s digest algorithm (x86 accelerated version)"
 	depends on X86 && 64BIT
 	select CRYPTO_LIB_BLAKE2S_GENERIC
 	select CRYPTO_ARCH_HAVE_LIB_BLAKE2S
@@ -1919,7 +1902,6 @@
 config CRYPTO_HASH_INFO
 	bool
 
-source "lib/crypto/Kconfig"
 source "drivers/crypto/Kconfig"
 source "crypto/asymmetric_keys/Kconfig"
 source "certs/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/Makefile
+++ linux-xilinx-zynqmp-5.15.0/crypto/Makefile
@@ -4,7 +4,7 @@
 #
 
 obj-$(CONFIG_CRYPTO) += crypto.o
-crypto-y := api.o cipher.o compress.o memneq.o
+crypto-y := api.o cipher.o compress.o
 
 obj-$(CONFIG_CRYPTO_ENGINE) += crypto_engine.o
 obj-$(CONFIG_CRYPTO_FIPS) += fips.o
@@ -83,7 +83,6 @@
 obj-$(CONFIG_CRYPTO_WP512) += wp512.o
 CFLAGS_wp512.o := $(call cc-option,-fno-schedule-insns)  # https://gcc.gnu.org/bugzilla/show_bug.cgi?id=79149
 obj-$(CONFIG_CRYPTO_BLAKE2B) += blake2b_generic.o
-obj-$(CONFIG_CRYPTO_BLAKE2S) += blake2s_generic.o
 obj-$(CONFIG_CRYPTO_GF128MUL) += gf128mul.o
 obj-$(CONFIG_CRYPTO_ECB) += ecb.o
 obj-$(CONFIG_CRYPTO_CBC) += cbc.o
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/aead.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/aead.c
@@ -35,8 +35,7 @@
 	alignbuffer = (u8 *)ALIGN((unsigned long)buffer, alignmask + 1);
 	memcpy(alignbuffer, key, keylen);
 	ret = crypto_aead_alg(tfm)->setkey(tfm, alignbuffer, keylen);
-	memset(alignbuffer, 0, keylen);
-	kfree(buffer);
+	kfree_sensitive(buffer);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/aegis128-neon-inner.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/aegis128-neon-inner.c
@@ -147,8 +147,8 @@
 		kiv,
 		vld1q_u8(const1),
 		vld1q_u8(const0),
-		k ^ vld1q_u8(const0),
-		k ^ vld1q_u8(const1),
+		(uint8x16_t) (k ^ vld1q_u8(const0)),
+		(uint8x16_t) (k ^ vld1q_u8(const1)),
 	}};
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/af_alg.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/af_alg.c
@@ -1045,9 +1045,13 @@
 void af_alg_free_resources(struct af_alg_async_req *areq)
 {
 	struct sock *sk = areq->sk;
+	struct af_alg_ctx *ctx;
 
 	af_alg_free_areq_sgls(areq);
 	sock_kfree_s(sk, areq, areq->areqlen);
+
+	ctx = alg_sk(sk)->private;
+	ctx->inflight = false;
 }
 EXPORT_SYMBOL_GPL(af_alg_free_resources);
 
@@ -1117,11 +1121,19 @@
 struct af_alg_async_req *af_alg_alloc_areq(struct sock *sk,
 					   unsigned int areqlen)
 {
-	struct af_alg_async_req *areq = sock_kmalloc(sk, areqlen, GFP_KERNEL);
+	struct af_alg_ctx *ctx = alg_sk(sk)->private;
+	struct af_alg_async_req *areq;
+
+	/* Only one AIO request can be in flight. */
+	if (ctx->inflight)
+		return ERR_PTR(-EBUSY);
 
+	areq = sock_kmalloc(sk, areqlen, GFP_KERNEL);
 	if (unlikely(!areq))
 		return ERR_PTR(-ENOMEM);
 
+	ctx->inflight = true;
+
 	areq->areqlen = areqlen;
 	areq->sk = sk;
 	areq->last_rsgl = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/akcipher.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/akcipher.c
@@ -120,6 +120,12 @@
 	return -ENOSYS;
 }
 
+static int akcipher_default_set_key(struct crypto_akcipher *tfm,
+				     const void *key, unsigned int keylen)
+{
+	return -ENOSYS;
+}
+
 int crypto_register_akcipher(struct akcipher_alg *alg)
 {
 	struct crypto_alg *base = &alg->base;
@@ -132,6 +138,8 @@
 		alg->encrypt = akcipher_default_op;
 	if (!alg->decrypt)
 		alg->decrypt = akcipher_default_op;
+	if (!alg->set_priv_key)
+		alg->set_priv_key = akcipher_default_set_key;
 
 	akcipher_prepare_alg(alg);
 	return crypto_register_alg(base);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/algapi.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/algapi.c
@@ -16,6 +16,7 @@
 #include <linux/rtnetlink.h>
 #include <linux/slab.h>
 #include <linux/string.h>
+#include <linux/workqueue.h>
 
 #include "internal.h"
 
@@ -68,15 +69,26 @@
 	inst->alg.cra_type->free(inst);
 }
 
-static void crypto_destroy_instance(struct crypto_alg *alg)
+static void crypto_destroy_instance_workfn(struct work_struct *w)
 {
-	struct crypto_instance *inst = (void *)alg;
+	struct crypto_instance *inst = container_of(w, struct crypto_instance,
+						    free_work);
 	struct crypto_template *tmpl = inst->tmpl;
 
 	crypto_free_instance(inst);
 	crypto_tmpl_put(tmpl);
 }
 
+static void crypto_destroy_instance(struct crypto_alg *alg)
+{
+	struct crypto_instance *inst = container_of(alg,
+						    struct crypto_instance,
+						    alg);
+
+	INIT_WORK(&inst->free_work, crypto_destroy_instance_workfn);
+	schedule_work(&inst->free_work);
+}
+
 /*
  * This function adds a spawn to the list secondary_spawns which
  * will be used at the end of crypto_remove_spawns to unregister
@@ -456,7 +468,9 @@
 	if (WARN(ret, "Algorithm %s is not registered", alg->cra_driver_name))
 		return;
 
-	BUG_ON(refcount_read(&alg->cra_refcnt) != 1);
+	if (WARN_ON(refcount_read(&alg->cra_refcnt) != 1))
+		return;
+
 	if (alg->cra_destroy)
 		alg->cra_destroy(alg);
 
@@ -918,6 +932,9 @@
 void crypto_enqueue_request_head(struct crypto_queue *queue,
 				 struct crypto_async_request *request)
 {
+	if (unlikely(queue->qlen >= queue->max_qlen))
+		queue->backlog = queue->backlog->prev;
+
 	queue->qlen++;
 	list_add(&request->list, &queue->list);
 }
@@ -1277,3 +1294,4 @@
 
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Cryptographic algorithms API");
+MODULE_SOFTDEP("pre: cryptomgr");
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/algboss.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/algboss.c
@@ -67,7 +67,7 @@
 	complete_all(&param->larval->completion);
 	crypto_alg_put(&param->larval->alg);
 	kfree(param);
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 }
 
 static int cryptomgr_schedule_probe(struct crypto_larval *larval)
@@ -190,7 +190,7 @@
 	crypto_alg_tested(param->driver, err);
 
 	kfree(param);
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 }
 
 static int cryptomgr_schedule_test(struct crypto_alg *alg)
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/api.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/api.c
@@ -603,4 +603,3 @@
 
 MODULE_DESCRIPTION("Cryptographic core API");
 MODULE_LICENSE("GPL");
-MODULE_SOFTDEP("pre: cryptomgr");
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/asymmetric_keys/pkcs7_verify.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/asymmetric_keys/pkcs7_verify.c
@@ -79,16 +79,16 @@
 		}
 
 		if (sinfo->msgdigest_len != sig->digest_size) {
-			pr_debug("Sig %u: Invalid digest size (%u)\n",
-				 sinfo->index, sinfo->msgdigest_len);
+			pr_warn("Sig %u: Invalid digest size (%u)\n",
+				sinfo->index, sinfo->msgdigest_len);
 			ret = -EBADMSG;
 			goto error;
 		}
 
 		if (memcmp(sig->digest, sinfo->msgdigest,
 			   sinfo->msgdigest_len) != 0) {
-			pr_debug("Sig %u: Message digest doesn't match\n",
-				 sinfo->index);
+			pr_warn("Sig %u: Message digest doesn't match\n",
+				sinfo->index);
 			ret = -EKEYREJECTED;
 			goto error;
 		}
@@ -174,12 +174,6 @@
 		pr_devel("Sig %u: Found cert serial match X.509[%u]\n",
 			 sinfo->index, certix);
 
-		if (strcmp(x509->pub->pkey_algo, sinfo->sig->pkey_algo) != 0) {
-			pr_warn("Sig %u: X.509 algo and PKCS#7 sig algo don't match\n",
-				sinfo->index);
-			continue;
-		}
-
 		sinfo->signer = x509;
 		return 0;
 	}
@@ -487,7 +481,7 @@
 			       const void *data, size_t datalen)
 {
 	if (pkcs7->data) {
-		pr_debug("Data already supplied\n");
+		pr_warn("Data already supplied\n");
 		return -EINVAL;
 	}
 	pkcs7->data = data;
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/asymmetric_keys/public_key.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/asymmetric_keys/public_key.c
@@ -60,39 +60,83 @@
 }
 
 /*
- * Determine the crypto algorithm name.
+ * Given a public_key, and an encoding and hash_algo to be used for signing
+ * and/or verification with that key, determine the name of the corresponding
+ * akcipher algorithm.  Also check that encoding and hash_algo are allowed.
  */
-static
-int software_key_determine_akcipher(const char *encoding,
-				    const char *hash_algo,
-				    const struct public_key *pkey,
-				    char alg_name[CRYPTO_MAX_ALG_NAME])
+static int
+software_key_determine_akcipher(const struct public_key *pkey,
+				const char *encoding, const char *hash_algo,
+				char alg_name[CRYPTO_MAX_ALG_NAME])
 {
 	int n;
 
-	if (strcmp(encoding, "pkcs1") == 0) {
-		/* The data wangled by the RSA algorithm is typically padded
-		 * and encoded in some manner, such as EMSA-PKCS1-1_5 [RFC3447
-		 * sec 8.2].
+	if (!encoding)
+		return -EINVAL;
+
+	if (strcmp(pkey->pkey_algo, "rsa") == 0) {
+		/*
+		 * RSA signatures usually use EMSA-PKCS1-1_5 [RFC3447 sec 8.2].
+		 */
+		if (strcmp(encoding, "pkcs1") == 0) {
+			if (!hash_algo)
+				n = snprintf(alg_name, CRYPTO_MAX_ALG_NAME,
+					     "pkcs1pad(%s)",
+					     pkey->pkey_algo);
+			else
+				n = snprintf(alg_name, CRYPTO_MAX_ALG_NAME,
+					     "pkcs1pad(%s,%s)",
+					     pkey->pkey_algo, hash_algo);
+			return n >= CRYPTO_MAX_ALG_NAME ? -EINVAL : 0;
+		}
+		if (strcmp(encoding, "raw") != 0)
+			return -EINVAL;
+		/*
+		 * Raw RSA cannot differentiate between different hash
+		 * algorithms.
+		 */
+		if (hash_algo)
+			return -EINVAL;
+	} else if (strncmp(pkey->pkey_algo, "ecdsa", 5) == 0) {
+		if (strcmp(encoding, "x962") != 0)
+			return -EINVAL;
+		/*
+		 * ECDSA signatures are taken over a raw hash, so they don't
+		 * differentiate between different hash algorithms.  That means
+		 * that the verifier should hard-code a specific hash algorithm.
+		 * Unfortunately, in practice ECDSA is used with multiple SHAs,
+		 * so we have to allow all of them and not just one.
 		 */
 		if (!hash_algo)
-			n = snprintf(alg_name, CRYPTO_MAX_ALG_NAME,
-				     "pkcs1pad(%s)",
-				     pkey->pkey_algo);
-		else
-			n = snprintf(alg_name, CRYPTO_MAX_ALG_NAME,
-				     "pkcs1pad(%s,%s)",
-				     pkey->pkey_algo, hash_algo);
-		return n >= CRYPTO_MAX_ALG_NAME ? -EINVAL : 0;
-	}
-
-	if (strcmp(encoding, "raw") == 0 ||
-	    strcmp(encoding, "x962") == 0) {
-		strcpy(alg_name, pkey->pkey_algo);
-		return 0;
+			return -EINVAL;
+		if (strcmp(hash_algo, "sha1") != 0 &&
+		    strcmp(hash_algo, "sha224") != 0 &&
+		    strcmp(hash_algo, "sha256") != 0 &&
+		    strcmp(hash_algo, "sha384") != 0 &&
+		    strcmp(hash_algo, "sha512") != 0)
+			return -EINVAL;
+	} else if (strcmp(pkey->pkey_algo, "sm2") == 0) {
+		if (strcmp(encoding, "raw") != 0)
+			return -EINVAL;
+		if (!hash_algo)
+			return -EINVAL;
+		if (strcmp(hash_algo, "sm3") != 0)
+			return -EINVAL;
+	} else if (strcmp(pkey->pkey_algo, "ecrdsa") == 0) {
+		if (strcmp(encoding, "raw") != 0)
+			return -EINVAL;
+		if (!hash_algo)
+			return -EINVAL;
+		if (strcmp(hash_algo, "streebog256") != 0 &&
+		    strcmp(hash_algo, "streebog512") != 0)
+			return -EINVAL;
+	} else {
+		/* Unknown public key algorithm */
+		return -ENOPKG;
 	}
-
-	return -ENOPKG;
+	if (strscpy(alg_name, pkey->pkey_algo, CRYPTO_MAX_ALG_NAME) < 0)
+		return -EINVAL;
+	return 0;
 }
 
 static u8 *pkey_pack_u32(u8 *dst, u32 val)
@@ -113,9 +157,8 @@
 	u8 *key, *ptr;
 	int ret, len;
 
-	ret = software_key_determine_akcipher(params->encoding,
-					      params->hash_algo,
-					      pkey, alg_name);
+	ret = software_key_determine_akcipher(pkey, params->encoding,
+					      params->hash_algo, alg_name);
 	if (ret < 0)
 		return ret;
 
@@ -143,8 +186,28 @@
 
 	len = crypto_akcipher_maxsize(tfm);
 	info->key_size = len * 8;
-	info->max_data_size = len;
-	info->max_sig_size = len;
+
+	if (strncmp(pkey->pkey_algo, "ecdsa", 5) == 0) {
+		/*
+		 * ECDSA key sizes are much smaller than RSA, and thus could
+		 * operate on (hashed) inputs that are larger than key size.
+		 * For example SHA384-hashed input used with secp256r1
+		 * based keys.  Set max_data_size to be at least as large as
+		 * the largest supported hash size (SHA512)
+		 */
+		info->max_data_size = 64;
+
+		/*
+		 * Verify takes ECDSA-Sig (described in RFC 5480) as input,
+		 * which is actually 2 'key_size'-bit integers encoded in
+		 * ASN.1.  Account for the ASN.1 encoding overhead here.
+		 */
+		info->max_sig_size = 2 * (len + 3) + 2;
+	} else {
+		info->max_data_size = len;
+		info->max_sig_size = len;
+	}
+
 	info->max_enc_size = len;
 	info->max_dec_size = len;
 	info->supported_ops = (KEYCTL_SUPPORTS_ENCRYPT |
@@ -179,9 +242,8 @@
 
 	pr_devel("==>%s()\n", __func__);
 
-	ret = software_key_determine_akcipher(params->encoding,
-					      params->hash_algo,
-					      pkey, alg_name);
+	ret = software_key_determine_akcipher(pkey, params->encoding,
+					      params->hash_algo, alg_name);
 	if (ret < 0)
 		return ret;
 
@@ -262,6 +324,10 @@
 
 	BUG_ON(!sig->data);
 
+	/* SM2 signatures always use the SM3 hash algorithm */
+	if (!sig->hash_algo || strcmp(sig->hash_algo, "sm3") != 0)
+		return -EINVAL;
+
 	ret = sm2_compute_z_digest(tfm_pkey, SM2_DEFAULT_USERID,
 					SM2_DEFAULT_USERID_LEN, dgst);
 	if (ret)
@@ -314,9 +380,10 @@
 	struct crypto_wait cwait;
 	struct crypto_akcipher *tfm;
 	struct akcipher_request *req;
-	struct scatterlist src_sg[2];
+	struct scatterlist src_sg;
 	char alg_name[CRYPTO_MAX_ALG_NAME];
-	char *key, *ptr;
+	char *buf, *ptr;
+	size_t buf_len;
 	int ret;
 
 	pr_devel("==>%s()\n", __func__);
@@ -325,9 +392,23 @@
 	BUG_ON(!sig);
 	BUG_ON(!sig->s);
 
-	ret = software_key_determine_akcipher(sig->encoding,
-					      sig->hash_algo,
-					      pkey, alg_name);
+	/*
+	 * If the signature specifies a public key algorithm, it *must* match
+	 * the key's actual public key algorithm.
+	 *
+	 * Small exception: ECDSA signatures don't specify the curve, but ECDSA
+	 * keys do.  So the strings can mismatch slightly in that case:
+	 * "ecdsa-nist-*" for the key, but "ecdsa" for the signature.
+	 */
+	if (sig->pkey_algo) {
+		if (strcmp(pkey->pkey_algo, sig->pkey_algo) != 0 &&
+		    (strncmp(pkey->pkey_algo, "ecdsa-", 6) != 0 ||
+		     strcmp(sig->pkey_algo, "ecdsa") != 0))
+			return -EKEYREJECTED;
+	}
+
+	ret = software_key_determine_akcipher(pkey, sig->encoding,
+					      sig->hash_algo, alg_name);
 	if (ret < 0)
 		return ret;
 
@@ -340,35 +421,37 @@
 	if (!req)
 		goto error_free_tfm;
 
-	key = kmalloc(pkey->keylen + sizeof(u32) * 2 + pkey->paramlen,
-		      GFP_KERNEL);
-	if (!key)
+	buf_len = max_t(size_t, pkey->keylen + sizeof(u32) * 2 + pkey->paramlen,
+			sig->s_size + sig->digest_size);
+
+	buf = kmalloc(buf_len, GFP_KERNEL);
+	if (!buf)
 		goto error_free_req;
 
-	memcpy(key, pkey->key, pkey->keylen);
-	ptr = key + pkey->keylen;
+	memcpy(buf, pkey->key, pkey->keylen);
+	ptr = buf + pkey->keylen;
 	ptr = pkey_pack_u32(ptr, pkey->algo);
 	ptr = pkey_pack_u32(ptr, pkey->paramlen);
 	memcpy(ptr, pkey->params, pkey->paramlen);
 
 	if (pkey->key_is_private)
-		ret = crypto_akcipher_set_priv_key(tfm, key, pkey->keylen);
+		ret = crypto_akcipher_set_priv_key(tfm, buf, pkey->keylen);
 	else
-		ret = crypto_akcipher_set_pub_key(tfm, key, pkey->keylen);
+		ret = crypto_akcipher_set_pub_key(tfm, buf, pkey->keylen);
 	if (ret)
-		goto error_free_key;
+		goto error_free_buf;
 
-	if (sig->pkey_algo && strcmp(sig->pkey_algo, "sm2") == 0 &&
-	    sig->data_size) {
+	if (strcmp(pkey->pkey_algo, "sm2") == 0 && sig->data_size) {
 		ret = cert_sig_digest_update(sig, tfm);
 		if (ret)
-			goto error_free_key;
+			goto error_free_buf;
 	}
 
-	sg_init_table(src_sg, 2);
-	sg_set_buf(&src_sg[0], sig->s, sig->s_size);
-	sg_set_buf(&src_sg[1], sig->digest, sig->digest_size);
-	akcipher_request_set_crypt(req, src_sg, NULL, sig->s_size,
+	memcpy(buf, sig->s, sig->s_size);
+	memcpy(buf + sig->s_size, sig->digest, sig->digest_size);
+
+	sg_init_one(&src_sg, buf, sig->s_size + sig->digest_size);
+	akcipher_request_set_crypt(req, &src_sg, NULL, sig->s_size,
 				   sig->digest_size);
 	crypto_init_wait(&cwait);
 	akcipher_request_set_callback(req, CRYPTO_TFM_REQ_MAY_BACKLOG |
@@ -376,8 +459,8 @@
 				      crypto_req_done, &cwait);
 	ret = crypto_wait_req(crypto_akcipher_verify(req), &cwait);
 
-error_free_key:
-	kfree(key);
+error_free_buf:
+	kfree(buf);
 error_free_req:
 	akcipher_request_free(req);
 error_free_tfm:
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/asymmetric_keys/verify_pefile.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/asymmetric_keys/verify_pefile.c
@@ -74,7 +74,7 @@
 		break;
 
 	default:
-		pr_debug("Unknown PEOPT magic = %04hx\n", pe32->magic);
+		pr_warn("Unknown PEOPT magic = %04hx\n", pe32->magic);
 		return -ELIBBAD;
 	}
 
@@ -95,7 +95,7 @@
 	ctx->certs_size = ddir->certs.size;
 
 	if (!ddir->certs.virtual_address || !ddir->certs.size) {
-		pr_debug("Unsigned PE binary\n");
+		pr_warn("Unsigned PE binary\n");
 		return -ENODATA;
 	}
 
@@ -127,7 +127,7 @@
 	unsigned len;
 
 	if (ctx->sig_len < sizeof(wrapper)) {
-		pr_debug("Signature wrapper too short\n");
+		pr_warn("Signature wrapper too short\n");
 		return -ELIBBAD;
 	}
 
@@ -135,19 +135,23 @@
 	pr_debug("sig wrapper = { %x, %x, %x }\n",
 		 wrapper.length, wrapper.revision, wrapper.cert_type);
 
-	/* Both pesign and sbsign round up the length of certificate table
-	 * (in optional header data directories) to 8 byte alignment.
+	/* sbsign rounds up the length of certificate table (in optional
+	 * header data directories) to 8 byte alignment.  However, the PE
+	 * specification states that while entries are 8-byte aligned, this is
+	 * not included in their length, and as a result, pesign has not
+	 * rounded up since 0.110.
 	 */
-	if (round_up(wrapper.length, 8) != ctx->sig_len) {
-		pr_debug("Signature wrapper len wrong\n");
+	if (wrapper.length > ctx->sig_len) {
+		pr_warn("Signature wrapper bigger than sig len (%x > %x)\n",
+			ctx->sig_len, wrapper.length);
 		return -ELIBBAD;
 	}
 	if (wrapper.revision != WIN_CERT_REVISION_2_0) {
-		pr_debug("Signature is not revision 2.0\n");
+		pr_warn("Signature is not revision 2.0\n");
 		return -ENOTSUPP;
 	}
 	if (wrapper.cert_type != WIN_CERT_TYPE_PKCS_SIGNED_DATA) {
-		pr_debug("Signature certificate type is not PKCS\n");
+		pr_warn("Signature certificate type is not PKCS\n");
 		return -ENOTSUPP;
 	}
 
@@ -160,7 +164,7 @@
 	ctx->sig_offset += sizeof(wrapper);
 	ctx->sig_len -= sizeof(wrapper);
 	if (ctx->sig_len < 4) {
-		pr_debug("Signature data missing\n");
+		pr_warn("Signature data missing\n");
 		return -EKEYREJECTED;
 	}
 
@@ -194,7 +198,7 @@
 		return 0;
 	}
 not_pkcs7:
-	pr_debug("Signature data not PKCS#7\n");
+	pr_warn("Signature data not PKCS#7\n");
 	return -ELIBBAD;
 }
 
@@ -337,8 +341,8 @@
 	digest_size = crypto_shash_digestsize(tfm);
 
 	if (digest_size != ctx->digest_len) {
-		pr_debug("Digest size mismatch (%zx != %x)\n",
-			 digest_size, ctx->digest_len);
+		pr_warn("Digest size mismatch (%zx != %x)\n",
+			digest_size, ctx->digest_len);
 		ret = -EBADMSG;
 		goto error_no_desc;
 	}
@@ -369,7 +373,7 @@
 	 * PKCS#7 certificate.
 	 */
 	if (memcmp(digest, ctx->digest, ctx->digest_len) != 0) {
-		pr_debug("Digest mismatch\n");
+		pr_warn("Digest mismatch\n");
 		ret = -EKEYREJECTED;
 	} else {
 		pr_debug("The digests match!\n");
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/asymmetric_keys/x509_public_key.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/asymmetric_keys/x509_public_key.c
@@ -128,11 +128,10 @@
 			goto out;
 	}
 
-	ret = -EKEYREJECTED;
-	if (strcmp(cert->pub->pkey_algo, cert->sig->pkey_algo) != 0 &&
-	    (strncmp(cert->pub->pkey_algo, "ecdsa-", 6) != 0 ||
-	     strcmp(cert->sig->pkey_algo, "ecdsa") != 0))
+	if (cert->unsupported_sig) {
+		ret = 0;
 		goto out;
+	}
 
 	ret = public_key_verify_signature(cert->pub, cert->sig);
 	if (ret < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/authenc.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/authenc.c
@@ -253,7 +253,7 @@
 		dst = scatterwalk_ffwd(areq_ctx->dst, req->dst, req->assoclen);
 
 	skcipher_request_set_tfm(skreq, ctx->enc);
-	skcipher_request_set_callback(skreq, aead_request_flags(req),
+	skcipher_request_set_callback(skreq, flags,
 				      req->base.complete, req->base.data);
 	skcipher_request_set_crypt(skreq, src, dst,
 				   req->cryptlen - authsize, req->iv);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/cipher.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/cipher.c
@@ -34,8 +34,7 @@
 	alignbuffer = (u8 *)ALIGN((unsigned long)buffer, alignmask + 1);
 	memcpy(alignbuffer, key, keylen);
 	ret = cia->cia_setkey(crypto_cipher_tfm(tfm), alignbuffer, keylen);
-	memset(alignbuffer, 0, keylen);
-	kfree(buffer);
+	kfree_sensitive(buffer);
 	return ret;
 
 }
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/cryptd.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/cryptd.c
@@ -39,6 +39,10 @@
 };
 
 struct cryptd_queue {
+	/*
+	 * Protected by disabling BH to allow enqueueing from softinterrupt and
+	 * dequeuing from kworker (cryptd_queue_worker()).
+	 */
 	struct cryptd_cpu_queue __percpu *cpu_queue;
 };
 
@@ -64,11 +68,12 @@
 
 struct cryptd_skcipher_ctx {
 	refcount_t refcnt;
-	struct crypto_sync_skcipher *child;
+	struct crypto_skcipher *child;
 };
 
 struct cryptd_skcipher_request_ctx {
 	crypto_completion_t complete;
+	struct skcipher_request req;
 };
 
 struct cryptd_hash_ctx {
@@ -125,28 +130,28 @@
 static int cryptd_enqueue_request(struct cryptd_queue *queue,
 				  struct crypto_async_request *request)
 {
-	int cpu, err;
+	int err;
 	struct cryptd_cpu_queue *cpu_queue;
 	refcount_t *refcnt;
 
-	cpu = get_cpu();
+	local_bh_disable();
 	cpu_queue = this_cpu_ptr(queue->cpu_queue);
 	err = crypto_enqueue_request(&cpu_queue->queue, request);
 
 	refcnt = crypto_tfm_ctx(request->tfm);
 
 	if (err == -ENOSPC)
-		goto out_put_cpu;
+		goto out;
 
-	queue_work_on(cpu, cryptd_wq, &cpu_queue->work);
+	queue_work_on(smp_processor_id(), cryptd_wq, &cpu_queue->work);
 
 	if (!refcount_read(refcnt))
-		goto out_put_cpu;
+		goto out;
 
 	refcount_inc(refcnt);
 
-out_put_cpu:
-	put_cpu();
+out:
+	local_bh_enable();
 
 	return err;
 }
@@ -162,15 +167,10 @@
 	cpu_queue = container_of(work, struct cryptd_cpu_queue, work);
 	/*
 	 * Only handle one request at a time to avoid hogging crypto workqueue.
-	 * preempt_disable/enable is used to prevent being preempted by
-	 * cryptd_enqueue_request(). local_bh_disable/enable is used to prevent
-	 * cryptd_enqueue_request() being accessed from software interrupts.
 	 */
 	local_bh_disable();
-	preempt_disable();
 	backlog = crypto_get_backlog(&cpu_queue->queue);
 	req = crypto_dequeue_request(&cpu_queue->queue);
-	preempt_enable();
 	local_bh_enable();
 
 	if (!req)
@@ -228,13 +228,13 @@
 				  const u8 *key, unsigned int keylen)
 {
 	struct cryptd_skcipher_ctx *ctx = crypto_skcipher_ctx(parent);
-	struct crypto_sync_skcipher *child = ctx->child;
+	struct crypto_skcipher *child = ctx->child;
 
-	crypto_sync_skcipher_clear_flags(child, CRYPTO_TFM_REQ_MASK);
-	crypto_sync_skcipher_set_flags(child,
-				       crypto_skcipher_get_flags(parent) &
-					 CRYPTO_TFM_REQ_MASK);
-	return crypto_sync_skcipher_setkey(child, key, keylen);
+	crypto_skcipher_clear_flags(child, CRYPTO_TFM_REQ_MASK);
+	crypto_skcipher_set_flags(child,
+				  crypto_skcipher_get_flags(parent) &
+				  CRYPTO_TFM_REQ_MASK);
+	return crypto_skcipher_setkey(child, key, keylen);
 }
 
 static void cryptd_skcipher_complete(struct skcipher_request *req, int err)
@@ -259,13 +259,13 @@
 	struct cryptd_skcipher_request_ctx *rctx = skcipher_request_ctx(req);
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct cryptd_skcipher_ctx *ctx = crypto_skcipher_ctx(tfm);
-	struct crypto_sync_skcipher *child = ctx->child;
-	SYNC_SKCIPHER_REQUEST_ON_STACK(subreq, child);
+	struct skcipher_request *subreq = &rctx->req;
+	struct crypto_skcipher *child = ctx->child;
 
 	if (unlikely(err == -EINPROGRESS))
 		goto out;
 
-	skcipher_request_set_sync_tfm(subreq, child);
+	skcipher_request_set_tfm(subreq, child);
 	skcipher_request_set_callback(subreq, CRYPTO_TFM_REQ_MAY_SLEEP,
 				      NULL, NULL);
 	skcipher_request_set_crypt(subreq, req->src, req->dst, req->cryptlen,
@@ -287,13 +287,13 @@
 	struct cryptd_skcipher_request_ctx *rctx = skcipher_request_ctx(req);
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct cryptd_skcipher_ctx *ctx = crypto_skcipher_ctx(tfm);
-	struct crypto_sync_skcipher *child = ctx->child;
-	SYNC_SKCIPHER_REQUEST_ON_STACK(subreq, child);
+	struct skcipher_request *subreq = &rctx->req;
+	struct crypto_skcipher *child = ctx->child;
 
 	if (unlikely(err == -EINPROGRESS))
 		goto out;
 
-	skcipher_request_set_sync_tfm(subreq, child);
+	skcipher_request_set_tfm(subreq, child);
 	skcipher_request_set_callback(subreq, CRYPTO_TFM_REQ_MAY_SLEEP,
 				      NULL, NULL);
 	skcipher_request_set_crypt(subreq, req->src, req->dst, req->cryptlen,
@@ -344,9 +344,10 @@
 	if (IS_ERR(cipher))
 		return PTR_ERR(cipher);
 
-	ctx->child = (struct crypto_sync_skcipher *)cipher;
+	ctx->child = cipher;
 	crypto_skcipher_set_reqsize(
-		tfm, sizeof(struct cryptd_skcipher_request_ctx));
+		tfm, sizeof(struct cryptd_skcipher_request_ctx) +
+		     crypto_skcipher_reqsize(cipher));
 	return 0;
 }
 
@@ -354,7 +355,7 @@
 {
 	struct cryptd_skcipher_ctx *ctx = crypto_skcipher_ctx(tfm);
 
-	crypto_free_sync_skcipher(ctx->child);
+	crypto_free_skcipher(ctx->child);
 }
 
 static void cryptd_skcipher_free(struct skcipher_instance *inst)
@@ -932,7 +933,7 @@
 {
 	struct cryptd_skcipher_ctx *ctx = crypto_skcipher_ctx(&tfm->base);
 
-	return &ctx->child->base;
+	return ctx->child;
 }
 EXPORT_SYMBOL_GPL(cryptd_skcipher_child);
 
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/crypto_engine.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/crypto_engine.c
@@ -53,7 +53,8 @@
 				dev_err(engine->dev, "failed to unprepare request\n");
 		}
 	}
-	req->complete(req, err);
+	lockdep_assert_in_softirq();
+	crypto_request_complete(req, err);
 
 	kthread_queue_work(engine->kworker, &engine->pump_requests);
 }
@@ -128,9 +129,6 @@
 	if (!engine->retry_support)
 		engine->cur_req = async_req;
 
-	if (backlog)
-		backlog->complete(backlog, -EINPROGRESS);
-
 	if (engine->busy)
 		was_busy = true;
 	else
@@ -213,9 +211,12 @@
 	}
 
 req_err_2:
-	async_req->complete(async_req, ret);
+	crypto_request_complete(async_req, ret);
 
 retry:
+	if (backlog)
+		crypto_request_complete(backlog, -EINPROGRESS);
+
 	/* If retry mechanism is supported, send new requests to engine */
 	if (engine->retry_support) {
 		spin_lock_irqsave(&engine->queue_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/drbg.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/drbg.c
@@ -1036,17 +1036,38 @@
  ******************************************************************/
 
 static inline int __drbg_seed(struct drbg_state *drbg, struct list_head *seed,
-			      int reseed)
+			      int reseed, enum drbg_seed_state new_seed_state)
 {
 	int ret = drbg->d_ops->update(drbg, seed, reseed);
 
 	if (ret)
 		return ret;
 
-	drbg->seeded = true;
+	drbg->seeded = new_seed_state;
 	/* 10.1.1.2 / 10.1.1.3 step 5 */
 	drbg->reseed_ctr = 1;
 
+	switch (drbg->seeded) {
+	case DRBG_SEED_STATE_UNSEEDED:
+		/* Impossible, but handle it to silence compiler warnings. */
+		fallthrough;
+	case DRBG_SEED_STATE_PARTIAL:
+		/*
+		 * Require frequent reseeds until the seed source is
+		 * fully initialized.
+		 */
+		drbg->reseed_threshold = 50;
+		break;
+
+	case DRBG_SEED_STATE_FULL:
+		/*
+		 * Seed source has become fully initialized, frequent
+		 * reseeds no longer required.
+		 */
+		drbg->reseed_threshold = drbg_max_requests(drbg);
+		break;
+	}
+
 	return ret;
 }
 
@@ -1066,12 +1087,10 @@
 	return 0;
 }
 
-static void drbg_async_seed(struct work_struct *work)
+static int drbg_seed_from_random(struct drbg_state *drbg)
 {
 	struct drbg_string data;
 	LIST_HEAD(seedlist);
-	struct drbg_state *drbg = container_of(work, struct drbg_state,
-					       seed_work);
 	unsigned int entropylen = drbg_sec_strength(drbg->core->flags);
 	unsigned char entropy[32];
 	int ret;
@@ -1082,26 +1101,15 @@
 	drbg_string_fill(&data, entropy, entropylen);
 	list_add_tail(&data.list, &seedlist);
 
-	mutex_lock(&drbg->drbg_mutex);
-
 	ret = drbg_get_random_bytes(drbg, entropy, entropylen);
 	if (ret)
-		goto unlock;
-
-	/* Set seeded to false so that if __drbg_seed fails the
-	 * next generate call will trigger a reseed.
-	 */
-	drbg->seeded = false;
-
-	__drbg_seed(drbg, &seedlist, true);
-
-	if (drbg->seeded)
-		drbg->reseed_threshold = drbg_max_requests(drbg);
+		goto out;
 
-unlock:
-	mutex_unlock(&drbg->drbg_mutex);
+	ret = __drbg_seed(drbg, &seedlist, true, DRBG_SEED_STATE_FULL);
 
+out:
 	memzero_explicit(entropy, entropylen);
+	return ret;
 }
 
 /*
@@ -1123,6 +1131,7 @@
 	unsigned int entropylen = drbg_sec_strength(drbg->core->flags);
 	struct drbg_string data1;
 	LIST_HEAD(seedlist);
+	enum drbg_seed_state new_seed_state = DRBG_SEED_STATE_FULL;
 
 	/* 9.1 / 9.2 / 9.3.1 step 3 */
 	if (pers && pers->len > (drbg_max_addtl(drbg))) {
@@ -1150,6 +1159,9 @@
 		BUG_ON((entropylen * 2) > sizeof(entropy));
 
 		/* Get seed from in-kernel /dev/urandom */
+		if (!rng_is_initialized())
+			new_seed_state = DRBG_SEED_STATE_PARTIAL;
+
 		ret = drbg_get_random_bytes(drbg, entropy, entropylen);
 		if (ret)
 			goto out;
@@ -1206,7 +1218,7 @@
 		memset(drbg->C, 0, drbg_statelen(drbg));
 	}
 
-	ret = __drbg_seed(drbg, &seedlist, reseed);
+	ret = __drbg_seed(drbg, &seedlist, reseed, new_seed_state);
 
 out:
 	memzero_explicit(entropy, entropylen * 2);
@@ -1386,19 +1398,25 @@
 	 * here. The spec is a bit convoluted here, we make it simpler.
 	 */
 	if (drbg->reseed_threshold < drbg->reseed_ctr)
-		drbg->seeded = false;
+		drbg->seeded = DRBG_SEED_STATE_UNSEEDED;
 
-	if (drbg->pr || !drbg->seeded) {
+	if (drbg->pr || drbg->seeded == DRBG_SEED_STATE_UNSEEDED) {
 		pr_devel("DRBG: reseeding before generation (prediction "
 			 "resistance: %s, state %s)\n",
 			 drbg->pr ? "true" : "false",
-			 drbg->seeded ? "seeded" : "unseeded");
+			 (drbg->seeded ==  DRBG_SEED_STATE_FULL ?
+			  "seeded" : "unseeded"));
 		/* 9.3.1 steps 7.1 through 7.3 */
 		len = drbg_seed(drbg, addtl, true);
 		if (len)
 			goto err;
 		/* 9.3.1 step 7.4 */
 		addtl = NULL;
+	} else if (rng_is_initialized() &&
+		   drbg->seeded == DRBG_SEED_STATE_PARTIAL) {
+		len = drbg_seed_from_random(drbg);
+		if (len)
+			goto err;
 	}
 
 	if (addtl && 0 < addtl->len)
@@ -1491,51 +1509,23 @@
 	return 0;
 }
 
-static void drbg_schedule_async_seed(struct random_ready_callback *rdy)
-{
-	struct drbg_state *drbg = container_of(rdy, struct drbg_state,
-					       random_ready);
-
-	schedule_work(&drbg->seed_work);
-}
-
 static int drbg_prepare_hrng(struct drbg_state *drbg)
 {
-	int err;
-
 	/* We do not need an HRNG in test mode. */
 	if (list_empty(&drbg->test_data.list))
 		return 0;
 
 	drbg->jent = crypto_alloc_rng("jitterentropy_rng", 0, 0);
+	if (IS_ERR(drbg->jent)) {
+		const int err = PTR_ERR(drbg->jent);
 
-	INIT_WORK(&drbg->seed_work, drbg_async_seed);
-
-	drbg->random_ready.owner = THIS_MODULE;
-	drbg->random_ready.func = drbg_schedule_async_seed;
-
-	err = add_random_ready_callback(&drbg->random_ready);
-
-	switch (err) {
-	case 0:
-		break;
-
-	case -EALREADY:
-		err = 0;
-		fallthrough;
-
-	default:
-		drbg->random_ready.func = NULL;
-		return err;
+		drbg->jent = NULL;
+		if (fips_enabled)
+			return err;
+		pr_info("DRBG: Continuing without Jitter RNG\n");
 	}
 
-	/*
-	 * Require frequent reseeds until the seed source is fully
-	 * initialized.
-	 */
-	drbg->reseed_threshold = 50;
-
-	return err;
+	return 0;
 }
 
 /*
@@ -1578,7 +1568,7 @@
 	if (!drbg->core) {
 		drbg->core = &drbg_cores[coreref];
 		drbg->pr = pr;
-		drbg->seeded = false;
+		drbg->seeded = DRBG_SEED_STATE_UNSEEDED;
 		drbg->reseed_threshold = drbg_max_requests(drbg);
 
 		ret = drbg_alloc_state(drbg);
@@ -1589,14 +1579,6 @@
 		if (ret)
 			goto free_everything;
 
-		if (IS_ERR(drbg->jent)) {
-			ret = PTR_ERR(drbg->jent);
-			drbg->jent = NULL;
-			if (fips_enabled || ret != -ENOENT)
-				goto free_everything;
-			pr_info("DRBG: Continuing without Jitter RNG\n");
-		}
-
 		reseed = false;
 	}
 
@@ -1629,11 +1611,6 @@
  */
 static int drbg_uninstantiate(struct drbg_state *drbg)
 {
-	if (drbg->random_ready.func) {
-		del_random_ready_callback(&drbg->random_ready);
-		cancel_work_sync(&drbg->seed_work);
-	}
-
 	if (!IS_ERR_OR_NULL(drbg->jent))
 		crypto_free_rng(drbg->jent);
 	drbg->jent = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/ecdh.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/ecdh.c
@@ -33,6 +33,8 @@
 	    params.key_size > sizeof(u64) * ctx->ndigits)
 		return -EINVAL;
 
+	memset(ctx->private_key, 0, sizeof(ctx->private_key));
+
 	if (!params.key || !params.key_size)
 		return ecc_gen_privkey(ctx->curve_id, ctx->ndigits,
 				       ctx->private_key);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/ecdsa.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/ecdsa.c
@@ -373,4 +373,7 @@
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Stefan Berger <stefanb@linux.ibm.com>");
 MODULE_DESCRIPTION("ECDSA generic algorithm");
+MODULE_ALIAS_CRYPTO("ecdsa-nist-p192");
+MODULE_ALIAS_CRYPTO("ecdsa-nist-p256");
+MODULE_ALIAS_CRYPTO("ecdsa-nist-p384");
 MODULE_ALIAS_CRYPTO("ecdsa-generic");
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/ecrdsa.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/ecrdsa.c
@@ -113,15 +113,15 @@
 
 	/* Step 1: verify that 0 < r < q, 0 < s < q */
 	if (vli_is_zero(r, ndigits) ||
-	    vli_cmp(r, ctx->curve->n, ndigits) == 1 ||
+	    vli_cmp(r, ctx->curve->n, ndigits) >= 0 ||
 	    vli_is_zero(s, ndigits) ||
-	    vli_cmp(s, ctx->curve->n, ndigits) == 1)
+	    vli_cmp(s, ctx->curve->n, ndigits) >= 0)
 		return -EKEYREJECTED;
 
 	/* Step 2: calculate hash (h) of the message (passed as input) */
 	/* Step 3: calculate e = h \mod q */
 	vli_from_le64(e, digest, ndigits);
-	if (vli_cmp(e, ctx->curve->n, ndigits) == 1)
+	if (vli_cmp(e, ctx->curve->n, ndigits) >= 0)
 		vli_sub(e, e, ctx->curve->n, ndigits);
 	if (vli_is_zero(e, ndigits))
 		e[0] = 1;
@@ -137,7 +137,7 @@
 	/* Step 6: calculate point C = z_1P + z_2Q, and R = x_c \mod q */
 	ecc_point_mult_shamir(&cc, z1, &ctx->curve->g, z2, &ctx->pub_key,
 			      ctx->curve);
-	if (vli_cmp(cc.x, ctx->curve->n, ndigits) == 1)
+	if (vli_cmp(cc.x, ctx->curve->n, ndigits) >= 0)
 		vli_sub(cc.x, cc.x, ctx->curve->n, ndigits);
 
 	/* Step 7: if R == r signature is valid */
@@ -294,4 +294,5 @@
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Vitaly Chikunov <vt@altlinux.org>");
 MODULE_DESCRIPTION("EC-RDSA generic algorithm");
+MODULE_ALIAS_CRYPTO("ecrdsa");
 MODULE_ALIAS_CRYPTO("ecrdsa-generic");
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/essiv.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/essiv.c
@@ -171,7 +171,12 @@
 	struct aead_request *req = areq->data;
 	struct essiv_aead_request_ctx *rctx = aead_request_ctx(req);
 
+	if (err == -EINPROGRESS)
+		goto out;
+
 	kfree(rctx->assoc);
+
+out:
 	aead_request_complete(req, err);
 }
 
@@ -247,7 +252,7 @@
 	err = enc ? crypto_aead_encrypt(subreq) :
 		    crypto_aead_decrypt(subreq);
 
-	if (rctx->assoc && err != -EINPROGRESS)
+	if (rctx->assoc && err != -EINPROGRESS && err != -EBUSY)
 		kfree(rctx->assoc);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/jitterentropy.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/jitterentropy.c
@@ -265,7 +265,6 @@
 {
 	__u64 delta2 = jent_delta(ec->last_delta, current_delta);
 	__u64 delta3 = jent_delta(ec->last_delta2, delta2);
-	unsigned int delta_masked = current_delta & JENT_APT_WORD_MASK;
 
 	ec->last_delta = current_delta;
 	ec->last_delta2 = delta2;
@@ -274,7 +273,7 @@
 	 * Insert the result of the comparison of two back-to-back time
 	 * deltas.
 	 */
-	jent_apt_insert(ec, delta_masked);
+	jent_apt_insert(ec, current_delta);
 
 	if (!current_delta || !delta2 || !delta3) {
 		/* RCT with a stuck bit */
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/lrw.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/lrw.c
@@ -357,10 +357,10 @@
 	 * cipher name.
 	 */
 	if (!strncmp(cipher_name, "ecb(", 4)) {
-		unsigned len;
+		int len;
 
-		len = strlcpy(ecb_name, cipher_name + 4, sizeof(ecb_name));
-		if (len < 2 || len >= sizeof(ecb_name))
+		len = strscpy(ecb_name, cipher_name + 4, sizeof(ecb_name));
+		if (len < 2)
 			goto err_free_inst;
 
 		if (ecb_name[len - 1] != ')')
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/pcrypt.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/pcrypt.c
@@ -78,12 +78,14 @@
 {
 	struct pcrypt_request *preq = pcrypt_padata_request(padata);
 	struct aead_request *req = pcrypt_request_ctx(preq);
+	int ret;
 
-	padata->info = crypto_aead_encrypt(req);
+	ret = crypto_aead_encrypt(req);
 
-	if (padata->info == -EINPROGRESS)
+	if (ret == -EINPROGRESS)
 		return;
 
+	padata->info = ret;
 	padata_do_serial(padata);
 }
 
@@ -115,6 +117,10 @@
 	err = padata_do_parallel(ictx->psenc, padata, &ctx->cb_cpu);
 	if (!err)
 		return -EINPROGRESS;
+	if (err == -EBUSY) {
+		/* try non-parallel mode */
+		return crypto_aead_encrypt(creq);
+	}
 
 	return err;
 }
@@ -123,12 +129,14 @@
 {
 	struct pcrypt_request *preq = pcrypt_padata_request(padata);
 	struct aead_request *req = pcrypt_request_ctx(preq);
+	int ret;
 
-	padata->info = crypto_aead_decrypt(req);
+	ret = crypto_aead_decrypt(req);
 
-	if (padata->info == -EINPROGRESS)
+	if (ret == -EINPROGRESS)
 		return;
 
+	padata->info = ret;
 	padata_do_serial(padata);
 }
 
@@ -160,6 +168,10 @@
 	err = padata_do_parallel(ictx->psdec, padata, &ctx->cb_cpu);
 	if (!err)
 		return -EINPROGRESS;
+	if (err == -EBUSY) {
+		/* try non-parallel mode */
+		return crypto_aead_decrypt(creq);
+	}
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/rsa-pkcs1pad.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/rsa-pkcs1pad.c
@@ -214,16 +214,14 @@
 		struct crypto_async_request *child_async_req, int err)
 {
 	struct akcipher_request *req = child_async_req->data;
-	struct crypto_async_request async_req;
 
 	if (err == -EINPROGRESS)
-		return;
+		goto out;
 
-	async_req.data = req->base.data;
-	async_req.tfm = crypto_akcipher_tfm(crypto_akcipher_reqtfm(req));
-	async_req.flags = child_async_req->flags;
-	req->base.complete(&async_req,
-			pkcs1pad_encrypt_sign_complete(req, err));
+	err = pkcs1pad_encrypt_sign_complete(req, err);
+
+out:
+	akcipher_request_complete(req, err);
 }
 
 static int pkcs1pad_encrypt(struct akcipher_request *req)
@@ -332,15 +330,14 @@
 		struct crypto_async_request *child_async_req, int err)
 {
 	struct akcipher_request *req = child_async_req->data;
-	struct crypto_async_request async_req;
 
 	if (err == -EINPROGRESS)
-		return;
+		goto out;
+
+	err = pkcs1pad_decrypt_complete(req, err);
 
-	async_req.data = req->base.data;
-	async_req.tfm = crypto_akcipher_tfm(crypto_akcipher_reqtfm(req));
-	async_req.flags = child_async_req->flags;
-	req->base.complete(&async_req, pkcs1pad_decrypt_complete(req, err));
+out:
+	akcipher_request_complete(req, err);
 }
 
 static int pkcs1pad_decrypt(struct akcipher_request *req)
@@ -476,6 +473,8 @@
 	pos++;
 
 	if (digest_info) {
+		if (digest_info->size > dst_len - pos)
+			goto done;
 		if (crypto_memneq(out_buf + pos, digest_info->data,
 				  digest_info->size))
 			goto done;
@@ -495,7 +494,7 @@
 			   sg_nents_for_len(req->src,
 					    req->src_len + req->dst_len),
 			   req_ctx->out_buf + ctx->key_size,
-			   req->dst_len, ctx->key_size);
+			   req->dst_len, req->src_len);
 	/* Do the actual verification step. */
 	if (memcmp(req_ctx->out_buf + ctx->key_size, out_buf + pos,
 		   req->dst_len) != 0)
@@ -510,15 +509,14 @@
 		struct crypto_async_request *child_async_req, int err)
 {
 	struct akcipher_request *req = child_async_req->data;
-	struct crypto_async_request async_req;
 
 	if (err == -EINPROGRESS)
-		return;
+		goto out;
 
-	async_req.data = req->base.data;
-	async_req.tfm = crypto_akcipher_tfm(crypto_akcipher_reqtfm(req));
-	async_req.flags = child_async_req->flags;
-	req->base.complete(&async_req, pkcs1pad_verify_complete(req, err));
+	err = pkcs1pad_verify_complete(req, err);
+
+out:
+	akcipher_request_complete(req, err);
 }
 
 /*
@@ -538,7 +536,7 @@
 
 	if (WARN_ON(req->dst) ||
 	    WARN_ON(!req->dst_len) ||
-	    !ctx->key_size || req->src_len < ctx->key_size)
+	    !ctx->key_size || req->src_len != ctx->key_size)
 		return -EINVAL;
 
 	req_ctx->out_buf = kmalloc(ctx->key_size + req->dst_len, GFP_KERNEL);
@@ -576,6 +574,10 @@
 		return PTR_ERR(child_tfm);
 
 	ctx->child = child_tfm;
+
+	akcipher_set_reqsize(tfm, sizeof(struct pkcs1pad_request) +
+				  crypto_akcipher_reqsize(child_tfm));
+
 	return 0;
 }
 
@@ -621,6 +623,11 @@
 
 	rsa_alg = crypto_spawn_akcipher_alg(&ctx->spawn);
 
+	if (strcmp(rsa_alg->base.cra_name, "rsa") != 0) {
+		err = -EINVAL;
+		goto err_free_inst;
+	}
+
 	err = -ENAMETOOLONG;
 	hash_name = crypto_attr_alg_name(tb[2]);
 	if (IS_ERR(hash_name)) {
@@ -666,7 +673,6 @@
 	inst->alg.set_pub_key = pkcs1pad_set_pub_key;
 	inst->alg.set_priv_key = pkcs1pad_set_priv_key;
 	inst->alg.max_size = pkcs1pad_get_max_size;
-	inst->alg.reqsize = sizeof(struct pkcs1pad_request) + rsa_alg->reqsize;
 
 	inst->free = pkcs1pad_free;
 
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/scompress.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/scompress.c
@@ -124,6 +124,7 @@
 	struct crypto_scomp *scomp = *tfm_ctx;
 	void **ctx = acomp_request_ctx(req);
 	struct scomp_scratch *scratch;
+	unsigned int dlen;
 	int ret;
 
 	if (!req->src || !req->slen || req->slen > SCOMP_SCRATCH_SIZE)
@@ -135,6 +136,8 @@
 	if (!req->dlen || req->dlen > SCOMP_SCRATCH_SIZE)
 		req->dlen = SCOMP_SCRATCH_SIZE;
 
+	dlen = req->dlen;
+
 	scratch = raw_cpu_ptr(&scomp_scratch);
 	spin_lock(&scratch->lock);
 
@@ -152,6 +155,9 @@
 				ret = -ENOMEM;
 				goto out;
 			}
+		} else if (req->dlen > dlen) {
+			ret = -ENOSPC;
+			goto out;
 		}
 		scatterwalk_map_and_copy(scratch->dst, req->dst, 0, req->dlen,
 					 1);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/seqiv.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/seqiv.c
@@ -23,7 +23,7 @@
 	struct aead_request *subreq = aead_request_ctx(req);
 	struct crypto_aead *geniv;
 
-	if (err == -EINPROGRESS)
+	if (err == -EINPROGRESS || err == -EBUSY)
 		return;
 
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/tcrypt.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/tcrypt.c
@@ -1295,15 +1295,6 @@
 			goto out_free_tfm;
 		}
 
-
-	for (i = 0; i < num_mb; ++i)
-		if (testmgr_alloc_buf(data[i].xbuf)) {
-			while (i--)
-				testmgr_free_buf(data[i].xbuf);
-			goto out_free_tfm;
-		}
-
-
 	for (i = 0; i < num_mb; ++i) {
 		data[i].req = skcipher_request_alloc(tfm, GFP_KERNEL);
 		if (!data[i].req) {
@@ -1333,7 +1324,7 @@
 
 			if (bs > XBUFSIZE * PAGE_SIZE) {
 				pr_err("template (%u) too big for buffer (%lu)\n",
-				       *b_size, XBUFSIZE * PAGE_SIZE);
+				       bs, XBUFSIZE * PAGE_SIZE);
 				goto out;
 			}
 
@@ -1386,8 +1377,7 @@
 				memset(cur->xbuf[p], 0xff, k);
 
 				skcipher_request_set_crypt(cur->req, cur->sg,
-							   cur->sg, *b_size,
-							   iv);
+							   cur->sg, bs, iv);
 			}
 
 			if (secs) {
@@ -1864,10 +1854,6 @@
 		ret += tcrypt_test("rmd160");
 		break;
 
-	case 41:
-		ret += tcrypt_test("blake2s-256");
-		break;
-
 	case 42:
 		ret += tcrypt_test("blake2b-512");
 		break;
@@ -2435,10 +2421,6 @@
 		test_hash_speed("rmd160", sec, generic_hash_speed_template);
 		if (mode > 300 && mode < 400) break;
 		fallthrough;
-	case 316:
-		test_hash_speed("blake2s-256", sec, generic_hash_speed_template);
-		if (mode > 300 && mode < 400) break;
-		fallthrough;
 	case 317:
 		test_hash_speed("blake2b-512", sec, generic_hash_speed_template);
 		if (mode > 300 && mode < 400) break;
@@ -2547,10 +2529,6 @@
 		test_ahash_speed("rmd160", sec, generic_hash_speed_template);
 		if (mode > 400 && mode < 500) break;
 		fallthrough;
-	case 416:
-		test_ahash_speed("blake2s-256", sec, generic_hash_speed_template);
-		if (mode > 400 && mode < 500) break;
-		fallthrough;
 	case 417:
 		test_ahash_speed("blake2b-512", sec, generic_hash_speed_template);
 		if (mode > 400 && mode < 500) break;
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/testmgr.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/testmgr.c
@@ -4330,30 +4330,6 @@
 			.hash = __VECS(blake2b_512_tv_template)
 		}
 	}, {
-		.alg = "blake2s-128",
-		.test = alg_test_hash,
-		.suite = {
-			.hash = __VECS(blakes2s_128_tv_template)
-		}
-	}, {
-		.alg = "blake2s-160",
-		.test = alg_test_hash,
-		.suite = {
-			.hash = __VECS(blakes2s_160_tv_template)
-		}
-	}, {
-		.alg = "blake2s-224",
-		.test = alg_test_hash,
-		.suite = {
-			.hash = __VECS(blakes2s_224_tv_template)
-		}
-	}, {
-		.alg = "blake2s-256",
-		.test = alg_test_hash,
-		.suite = {
-			.hash = __VECS(blakes2s_256_tv_template)
-		}
-	}, {
 		.alg = "cbc(aes)",
 		.test = alg_test_skcipher,
 		.fips_allowed = 1,
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/testmgr.h
+++ linux-xilinx-zynqmp-5.15.0/crypto/testmgr.h
@@ -183,8 +183,8 @@
 	{
 #ifndef CONFIG_CRYPTO_FIPS
 	.key =
-	"\x30\x81\x9A" /* sequence of 154 bytes */
-	"\x02\x01\x01" /* version - integer of 1 byte */
+	"\x30\x82\x01\x38" /* sequence of 312 bytes */
+	"\x02\x01\x00" /* version - integer of 1 byte */
 	"\x02\x41" /* modulus - integer of 65 bytes */
 	"\x00\xAA\x36\xAB\xCE\x88\xAC\xFD\xFF\x55\x52\x3C\x7F\xC4\x52\x3F"
 	"\x90\xEF\xA0\x0D\xF3\x77\x4A\x25\x9F\x2E\x62\xB4\xC5\xD9\x9C\xB5"
@@ -197,24 +197,37 @@
 	"\xC2\xCD\x2D\xFF\x43\x40\x98\xCD\x20\xD8\xA1\x38\xD0\x90\xBF\x64"
 	"\x79\x7C\x3F\xA7\xA2\xCD\xCB\x3C\xD1\xE0\xBD\xBA\x26\x54\xB4\xF9"
 	"\xDF\x8E\x8A\xE5\x9D\x73\x3D\x9F\x33\xB3\x01\x62\x4A\xFD\x1D\x51"
-	"\x02\x01\x00" /* prime1 - integer of 1 byte */
-	"\x02\x01\x00" /* prime2 - integer of 1 byte */
-	"\x02\x01\x00" /* exponent1 - integer of 1 byte */
-	"\x02\x01\x00" /* exponent2 - integer of 1 byte */
-	"\x02\x01\x00", /* coefficient - integer of 1 byte */
+	"\x02\x21" /* prime1 - integer of 33 bytes */
+	"\x00\xD8\x40\xB4\x16\x66\xB4\x2E\x92\xEA\x0D\xA3\xB4\x32\x04\xB5"
+	"\xCF\xCE\x33\x52\x52\x4D\x04\x16\xA5\xA4\x41\xE7\x00\xAF\x46\x12"
+	"\x0D"
+	"\x02\x21" /* prime2 - integer of 33 bytes */
+	"\x00\xC9\x7F\xB1\xF0\x27\xF4\x53\xF6\x34\x12\x33\xEA\xAA\xD1\xD9"
+	"\x35\x3F\x6C\x42\xD0\x88\x66\xB1\xD0\x5A\x0F\x20\x35\x02\x8B\x9D"
+	"\x89"
+	"\x02\x20" /* exponent1 - integer of 32 bytes */
+	"\x59\x0B\x95\x72\xA2\xC2\xA9\xC4\x06\x05\x9D\xC2\xAB\x2F\x1D\xAF"
+	"\xEB\x7E\x8B\x4F\x10\xA7\x54\x9E\x8E\xED\xF5\xB4\xFC\xE0\x9E\x05"
+	"\x02\x21" /* exponent2 - integer of 33 bytes */
+	"\x00\x8E\x3C\x05\x21\xFE\x15\xE0\xEA\x06\xA3\x6F\xF0\xF1\x0C\x99"
+	"\x52\xC3\x5B\x7A\x75\x14\xFD\x32\x38\xB8\x0A\xAD\x52\x98\x62\x8D"
+	"\x51"
+	"\x02\x20" /* coefficient - integer of 32 bytes */
+	"\x36\x3F\xF7\x18\x9D\xA8\xE9\x0B\x1D\x34\x1F\x71\xD0\x9B\x76\xA8"
+	"\xA9\x43\xE1\x1D\x10\xB2\x4D\x24\x9F\x2D\xEA\xFE\xF8\x0C\x18\x26",
 	.m = "\x54\x85\x9b\x34\x2c\x49\xea\x2a",
 	.c =
 	"\x63\x1c\xcd\x7b\xe1\x7e\xe4\xde\xc9\xa8\x89\xa1\x74\xcb\x3c\x63"
 	"\x7d\x24\xec\x83\xc3\x15\xe4\x7f\x73\x05\x34\xd1\xec\x22\xbb\x8a"
 	"\x5e\x32\x39\x6d\xc1\x1d\x7d\x50\x3b\x9f\x7a\xad\xf0\x2e\x25\x53"
 	"\x9f\x6e\xbd\x4c\x55\x84\x0c\x9b\xcf\x1a\x4b\x51\x1e\x9e\x0c\x06",
-	.key_len = 157,
+	.key_len = 316,
 	.m_size = 8,
 	.c_size = 64,
 	}, {
 	.key =
-	"\x30\x82\x01\x1D" /* sequence of 285 bytes */
-	"\x02\x01\x01" /* version - integer of 1 byte */
+	"\x30\x82\x02\x5B" /* sequence of 603 bytes */
+	"\x02\x01\x00" /* version - integer of 1 byte */
 	"\x02\x81\x81" /* modulus - integer of 129 bytes */
 	"\x00\xBB\xF8\x2F\x09\x06\x82\xCE\x9C\x23\x38\xAC\x2B\x9D\xA8\x71"
 	"\xF7\x36\x8D\x07\xEE\xD4\x10\x43\xA4\x40\xD6\xB6\xF0\x74\x54\xF5"
@@ -236,12 +249,35 @@
 	"\x93\x99\x26\xED\x4F\x74\xA1\x3E\xDD\xFB\xE1\xA1\xCE\xCC\x48\x94"
 	"\xAF\x94\x28\xC2\xB7\xB8\x88\x3F\xE4\x46\x3A\x4B\xC8\x5B\x1C\xB3"
 	"\xC1"
-	"\x02\x01\x00" /* prime1 - integer of 1 byte */
-	"\x02\x01\x00" /* prime2 - integer of 1 byte */
-	"\x02\x01\x00" /* exponent1 - integer of 1 byte */
-	"\x02\x01\x00" /* exponent2 - integer of 1 byte */
-	"\x02\x01\x00", /* coefficient - integer of 1 byte */
-	.key_len = 289,
+	"\x02\x41" /* prime1 - integer of 65 bytes */
+	"\x00\xEE\xCF\xAE\x81\xB1\xB9\xB3\xC9\x08\x81\x0B\x10\xA1\xB5\x60"
+	"\x01\x99\xEB\x9F\x44\xAE\xF4\xFD\xA4\x93\xB8\x1A\x9E\x3D\x84\xF6"
+	"\x32\x12\x4E\xF0\x23\x6E\x5D\x1E\x3B\x7E\x28\xFA\xE7\xAA\x04\x0A"
+	"\x2D\x5B\x25\x21\x76\x45\x9D\x1F\x39\x75\x41\xBA\x2A\x58\xFB\x65"
+	"\x99"
+	"\x02\x41" /* prime2 - integer of 65 bytes */
+	"\x00\xC9\x7F\xB1\xF0\x27\xF4\x53\xF6\x34\x12\x33\xEA\xAA\xD1\xD9"
+	"\x35\x3F\x6C\x42\xD0\x88\x66\xB1\xD0\x5A\x0F\x20\x35\x02\x8B\x9D"
+	"\x86\x98\x40\xB4\x16\x66\xB4\x2E\x92\xEA\x0D\xA3\xB4\x32\x04\xB5"
+	"\xCF\xCE\x33\x52\x52\x4D\x04\x16\xA5\xA4\x41\xE7\x00\xAF\x46\x15"
+	"\x03"
+	"\x02\x40" /* exponent1 - integer of 64 bytes */
+	"\x54\x49\x4C\xA6\x3E\xBA\x03\x37\xE4\xE2\x40\x23\xFC\xD6\x9A\x5A"
+	"\xEB\x07\xDD\xDC\x01\x83\xA4\xD0\xAC\x9B\x54\xB0\x51\xF2\xB1\x3E"
+	"\xD9\x49\x09\x75\xEA\xB7\x74\x14\xFF\x59\xC1\xF7\x69\x2E\x9A\x2E"
+	"\x20\x2B\x38\xFC\x91\x0A\x47\x41\x74\xAD\xC9\x3C\x1F\x67\xC9\x81"
+	"\x02\x40" /* exponent2 - integer of 64 bytes */
+	"\x47\x1E\x02\x90\xFF\x0A\xF0\x75\x03\x51\xB7\xF8\x78\x86\x4C\xA9"
+	"\x61\xAD\xBD\x3A\x8A\x7E\x99\x1C\x5C\x05\x56\xA9\x4C\x31\x46\xA7"
+	"\xF9\x80\x3F\x8F\x6F\x8A\xE3\x42\xE9\x31\xFD\x8A\xE4\x7A\x22\x0D"
+	"\x1B\x99\xA4\x95\x84\x98\x07\xFE\x39\xF9\x24\x5A\x98\x36\xDA\x3D"
+	"\x02\x41" /* coefficient - integer of 65 bytes */
+	"\x00\xB0\x6C\x4F\xDA\xBB\x63\x01\x19\x8D\x26\x5B\xDB\xAE\x94\x23"
+	"\xB3\x80\xF2\x71\xF7\x34\x53\x88\x50\x93\x07\x7F\xCD\x39\xE2\x11"
+	"\x9F\xC9\x86\x32\x15\x4F\x58\x83\xB1\x67\xA9\x67\xBF\x40\x2B\x4E"
+	"\x9E\x2E\x0F\x96\x56\xE6\x98\xEA\x36\x66\xED\xFB\x25\x79\x80\x39"
+	"\xF7",
+	.key_len = 607,
 	.m = "\x54\x85\x9b\x34\x2c\x49\xea\x2a",
 	.c =
 	"\x74\x1b\x55\xac\x47\xb5\x08\x0a\x6e\x2b\x2d\xf7\x94\xb8\x8a\x95"
@@ -257,9 +293,9 @@
 	}, {
 #endif
 	.key =
-	"\x30\x82\x02\x1F" /* sequence of 543 bytes */
-	"\x02\x01\x01" /* version - integer of 1 byte */
-	"\x02\x82\x01\x00" /* modulus - integer of 256 bytes */
+	"\x30\x82\x04\xA3" /* sequence of 1187 bytes */
+	"\x02\x01\x00" /* version - integer of 1 byte */
+	"\x02\x82\x01\x01\x00" /* modulus - integer of 256 bytes */
 	"\xDB\x10\x1A\xC2\xA3\xF1\xDC\xFF\x13\x6B\xED\x44\xDF\xF0\x02\x6D"
 	"\x13\xC7\x88\xDA\x70\x6B\x54\xF1\xE8\x27\xDC\xC3\x0F\x99\x6A\xFA"
 	"\xC6\x67\xFF\x1D\x1E\x3C\x1D\xC1\xB5\x5F\x6C\xC0\xB2\x07\x3A\x6D"
@@ -294,12 +330,55 @@
 	"\x62\xFF\xE9\x46\xB8\xD8\x44\xDB\xA5\xCC\x31\x54\x34\xCE\x3E\x82"
 	"\xD6\xBF\x7A\x0B\x64\x21\x6D\x88\x7E\x5B\x45\x12\x1E\x63\x8D\x49"
 	"\xA7\x1D\xD9\x1E\x06\xCD\xE8\xBA\x2C\x8C\x69\x32\xEA\xBE\x60\x71"
-	"\x02\x01\x00" /* prime1 - integer of 1 byte */
-	"\x02\x01\x00" /* prime2 - integer of 1 byte */
-	"\x02\x01\x00" /* exponent1 - integer of 1 byte */
-	"\x02\x01\x00" /* exponent2 - integer of 1 byte */
-	"\x02\x01\x00", /* coefficient - integer of 1 byte */
-	.key_len = 547,
+	"\x02\x81\x81" /* prime1 - integer of 129 bytes */
+	"\x00\xFA\xAC\xE1\x37\x5E\x32\x11\x34\xC6\x72\x58\x2D\x91\x06\x3E"
+	"\x77\xE7\x11\x21\xCD\x4A\xF8\xA4\x3F\x0F\xEF\x31\xE3\xF3\x55\xA0"
+	"\xB9\xAC\xB6\xCB\xBB\x41\xD0\x32\x81\x9A\x8F\x7A\x99\x30\x77\x6C"
+	"\x68\x27\xE2\x96\xB5\x72\xC9\xC3\xD4\x42\xAA\xAA\xCA\x95\x8F\xFF"
+	"\xC9\x9B\x52\x34\x30\x1D\xCF\xFE\xCF\x3C\x56\x68\x6E\xEF\xE7\x6C"
+	"\xD7\xFB\x99\xF5\x4A\xA5\x21\x1F\x2B\xEA\x93\xE8\x98\x26\xC4\x6E"
+	"\x42\x21\x5E\xA0\xA1\x2A\x58\x35\xBB\x10\xE7\xBA\x27\x0A\x3B\xB3"
+	"\xAF\xE2\x75\x36\x04\xAC\x56\xA0\xAB\x52\xDE\xCE\xDD\x2C\x28\x77"
+	"\x03"
+	"\x02\x81\x81" /* prime2 - integer of 129 bytes */
+	"\x00\xDF\xB7\x52\xB6\xD7\xC0\xE2\x96\xE7\xC9\xFE\x5D\x71\x5A\xC4"
+	"\x40\x96\x2F\xE5\x87\xEA\xF3\xA5\x77\x11\x67\x3C\x8D\x56\x08\xA7"
+	"\xB5\x67\xFA\x37\xA8\xB8\xCF\x61\xE8\x63\xD8\x38\x06\x21\x2B\x92"
+	"\x09\xA6\x39\x3A\xEA\xA8\xB4\x45\x4B\x36\x10\x4C\xE4\x00\x66\x71"
+	"\x65\xF8\x0B\x94\x59\x4F\x8C\xFD\xD5\x34\xA2\xE7\x62\x84\x0A\xA7"
+	"\xBB\xDB\xD9\x8A\xCD\x05\xE1\xCC\x57\x7B\xF1\xF1\x1F\x11\x9D\xBA"
+	"\x3E\x45\x18\x99\x1B\x41\x64\x43\xEE\x97\x5D\x77\x13\x5B\x74\x69"
+	"\x73\x87\x95\x05\x07\xBE\x45\x07\x17\x7E\x4A\x69\x22\xF3\xDB\x05"
+	"\x39"
+	"\x02\x81\x80" /* exponent1 - integer of 128 bytes */
+	"\x5E\xD8\xDC\xDA\x53\x44\xC4\x67\xE0\x92\x51\x34\xE4\x83\xA5\x4D"
+	"\x3E\xDB\xA7\x9B\x82\xBB\x73\x81\xFC\xE8\x77\x4B\x15\xBE\x17\x73"
+	"\x49\x9B\x5C\x98\xBC\xBD\x26\xEF\x0C\xE9\x2E\xED\x19\x7E\x86\x41"
+	"\x1E\x9E\x48\x81\xDD\x2D\xE4\x6F\xC2\xCD\xCA\x93\x9E\x65\x7E\xD5"
+	"\xEC\x73\xFD\x15\x1B\xA2\xA0\x7A\x0F\x0D\x6E\xB4\x53\x07\x90\x92"
+	"\x64\x3B\x8B\xA9\x33\xB3\xC5\x94\x9B\x4C\x5D\x9C\x7C\x46\xA4\xA5"
+	"\x56\xF4\xF3\xF8\x27\x0A\x7B\x42\x0D\x92\x70\x47\xE7\x42\x51\xA9"
+	"\xC2\x18\xB1\x58\xB1\x50\x91\xB8\x61\x41\xB6\xA9\xCE\xD4\x7C\xBB"
+	"\x02\x81\x80" /* exponent2 - integer of 128 bytes */
+	"\x54\x09\x1F\x0F\x03\xD8\xB6\xC5\x0C\xE8\xB9\x9E\x0C\x38\x96\x43"
+	"\xD4\xA6\xC5\x47\xDB\x20\x0E\xE5\xBD\x29\xD4\x7B\x1A\xF8\x41\x57"
+	"\x49\x69\x9A\x82\xCC\x79\x4A\x43\xEB\x4D\x8B\x2D\xF2\x43\xD5\xA5"
+	"\xBE\x44\xFD\x36\xAC\x8C\x9B\x02\xF7\x9A\x03\xE8\x19\xA6\x61\xAE"
+	"\x76\x10\x93\x77\x41\x04\xAB\x4C\xED\x6A\xCC\x14\x1B\x99\x8D\x0C"
+	"\x6A\x37\x3B\x86\x6C\x51\x37\x5B\x1D\x79\xF2\xA3\x43\x10\xC6\xA7"
+	"\x21\x79\x6D\xF9\xE9\x04\x6A\xE8\x32\xFF\xAE\xFD\x1C\x7B\x8C\x29"
+	"\x13\xA3\x0C\xB2\xAD\xEC\x6C\x0F\x8D\x27\x12\x7B\x48\xB2\xDB\x31"
+	"\x02\x81\x81" /* coefficient - integer of 129 bytes */
+	"\x00\x8D\x1B\x05\xCA\x24\x1F\x0C\x53\x19\x52\x74\x63\x21\xFA\x78"
+	"\x46\x79\xAF\x5C\xDE\x30\xA4\x6C\x20\x38\xE6\x97\x39\xB8\x7A\x70"
+	"\x0D\x8B\x6C\x6D\x13\x74\xD5\x1C\xDE\xA9\xF4\x60\x37\xFE\x68\x77"
+	"\x5E\x0B\x4E\x5E\x03\x31\x30\xDF\xD6\xAE\x85\xD0\x81\xBB\x61\xC7"
+	"\xB1\x04\x5A\xC4\x6D\x56\x1C\xD9\x64\xE7\x85\x7F\x88\x91\xC9\x60"
+	"\x28\x05\xE2\xC6\x24\x8F\xDD\x61\x64\xD8\x09\xDE\x7E\xD3\x4A\x61"
+	"\x1A\xD3\x73\x58\x4B\xD8\xA0\x54\x25\x48\x83\x6F\x82\x6C\xAF\x36"
+	"\x51\x2A\x5D\x14\x2F\x41\x25\x00\xDD\xF8\xF3\x95\xFE\x31\x25\x50"
+	"\x12",
+	.key_len = 1191,
 	.m = "\x54\x85\x9b\x34\x2c\x49\xea\x2a",
 	.c =
 	"\xb2\x97\x76\xb4\xae\x3e\x38\x3c\x7e\x64\x1f\xcc\xa2\x7f\xf6\xbe"
@@ -1150,7 +1229,7 @@
 static const struct akcipher_testvec pkcs1pad_rsa_tv_template[] = {
 	{
 	.key =
-	"\x30\x82\x03\x1f\x02\x01\x00\x02\x82\x01\x01\x00\xd7\x1e\x77\x82"
+	"\x30\x82\x04\xa5\x02\x01\x00\x02\x82\x01\x01\x00\xd7\x1e\x77\x82"
 	"\x8c\x92\x31\xe7\x69\x02\xa2\xd5\x5c\x78\xde\xa2\x0c\x8f\xfe\x28"
 	"\x59\x31\xdf\x40\x9c\x60\x61\x06\xb9\x2f\x62\x40\x80\x76\xcb\x67"
 	"\x4a\xb5\x59\x56\x69\x17\x07\xfa\xf9\x4c\xbd\x6c\x37\x7a\x46\x7d"
@@ -1166,42 +1245,66 @@
 	"\x9e\x49\x63\x6e\x02\xc1\xc9\x3a\x9b\xa5\x22\x1b\x07\x95\xd6\x10"
 	"\x02\x50\xfd\xfd\xd1\x9b\xbe\xab\xc2\xc0\x74\xd7\xec\x00\xfb\x11"
 	"\x71\xcb\x7a\xdc\x81\x79\x9f\x86\x68\x46\x63\x82\x4d\xb7\xf1\xe6"
-	"\x16\x6f\x42\x63\xf4\x94\xa0\xca\x33\xcc\x75\x13\x02\x82\x01\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
-	"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x01\x00\x01"
-	"\x02\x82\x01\x00\x62\xb5\x60\x31\x4f\x3f\x66\x16\xc1\x60\xac\x47"
-	"\x2a\xff\x6b\x69\x00\x4a\xb2\x5c\xe1\x50\xb9\x18\x74\xa8\xe4\xdc"
-	"\xa8\xec\xcd\x30\xbb\xc1\xc6\xe3\xc6\xac\x20\x2a\x3e\x5e\x8b\x12"
-	"\xe6\x82\x08\x09\x38\x0b\xab\x7c\xb3\xcc\x9c\xce\x97\x67\xdd\xef"
-	"\x95\x40\x4e\x92\xe2\x44\xe9\x1d\xc1\x14\xfd\xa9\xb1\xdc\x71\x9c"
-	"\x46\x21\xbd\x58\x88\x6e\x22\x15\x56\xc1\xef\xe0\xc9\x8d\xe5\x80"
-	"\x3e\xda\x7e\x93\x0f\x52\xf6\xf5\xc1\x91\x90\x9e\x42\x49\x4f\x8d"
-	"\x9c\xba\x38\x83\xe9\x33\xc2\x50\x4f\xec\xc2\xf0\xa8\xb7\x6e\x28"
-	"\x25\x56\x6b\x62\x67\xfe\x08\xf1\x56\xe5\x6f\x0e\x99\xf1\xe5\x95"
-	"\x7b\xef\xeb\x0a\x2c\x92\x97\x57\x23\x33\x36\x07\xdd\xfb\xae\xf1"
-	"\xb1\xd8\x33\xb7\x96\x71\x42\x36\xc5\xa4\xa9\x19\x4b\x1b\x52\x4c"
-	"\x50\x69\x91\xf0\x0e\xfa\x80\x37\x4b\xb5\xd0\x2f\xb7\x44\x0d\xd4"
-	"\xf8\x39\x8d\xab\x71\x67\x59\x05\x88\x3d\xeb\x48\x48\x33\x88\x4e"
-	"\xfe\xf8\x27\x1b\xd6\x55\x60\x5e\x48\xb7\x6d\x9a\xa8\x37\xf9\x7a"
-	"\xde\x1b\xcd\x5d\x1a\x30\xd4\xe9\x9e\x5b\x3c\x15\xf8\x9c\x1f\xda"
-	"\xd1\x86\x48\x55\xce\x83\xee\x8e\x51\xc7\xde\x32\x12\x47\x7d\x46"
-	"\xb8\x35\xdf\x41\x02\x01\x00\x02\x01\x00\x02\x01\x00\x02\x01\x00"
-	"\x02\x01\x00",
-	.key_len = 804,
+	"\x16\x6f\x42\x63\xf4\x94\xa0\xca\x33\xcc\x75\x13\x02\x03\x01\x00"
+	"\x01\x02\x82\x01\x00\x62\xb5\x60\x31\x4f\x3f\x66\x16\xc1\x60\xac"
+	"\x47\x2a\xff\x6b\x69\x00\x4a\xb2\x5c\xe1\x50\xb9\x18\x74\xa8\xe4"
+	"\xdc\xa8\xec\xcd\x30\xbb\xc1\xc6\xe3\xc6\xac\x20\x2a\x3e\x5e\x8b"
+	"\x12\xe6\x82\x08\x09\x38\x0b\xab\x7c\xb3\xcc\x9c\xce\x97\x67\xdd"
+	"\xef\x95\x40\x4e\x92\xe2\x44\xe9\x1d\xc1\x14\xfd\xa9\xb1\xdc\x71"
+	"\x9c\x46\x21\xbd\x58\x88\x6e\x22\x15\x56\xc1\xef\xe0\xc9\x8d\xe5"
+	"\x80\x3e\xda\x7e\x93\x0f\x52\xf6\xf5\xc1\x91\x90\x9e\x42\x49\x4f"
+	"\x8d\x9c\xba\x38\x83\xe9\x33\xc2\x50\x4f\xec\xc2\xf0\xa8\xb7\x6e"
+	"\x28\x25\x56\x6b\x62\x67\xfe\x08\xf1\x56\xe5\x6f\x0e\x99\xf1\xe5"
+	"\x95\x7b\xef\xeb\x0a\x2c\x92\x97\x57\x23\x33\x36\x07\xdd\xfb\xae"
+	"\xf1\xb1\xd8\x33\xb7\x96\x71\x42\x36\xc5\xa4\xa9\x19\x4b\x1b\x52"
+	"\x4c\x50\x69\x91\xf0\x0e\xfa\x80\x37\x4b\xb5\xd0\x2f\xb7\x44\x0d"
+	"\xd4\xf8\x39\x8d\xab\x71\x67\x59\x05\x88\x3d\xeb\x48\x48\x33\x88"
+	"\x4e\xfe\xf8\x27\x1b\xd6\x55\x60\x5e\x48\xb7\x6d\x9a\xa8\x37\xf9"
+	"\x7a\xde\x1b\xcd\x5d\x1a\x30\xd4\xe9\x9e\x5b\x3c\x15\xf8\x9c\x1f"
+	"\xda\xd1\x86\x48\x55\xce\x83\xee\x8e\x51\xc7\xde\x32\x12\x47\x7d"
+	"\x46\xb8\x35\xdf\x41\x02\x81\x81\x00\xe4\x4c\xae\xde\x16\xfd\x9f"
+	"\x83\x55\x5b\x84\x4a\xcf\x1c\xf1\x37\x95\xad\xca\x29\x7f\x2d\x6e"
+	"\x32\x81\xa4\x2b\x26\x14\x96\x1d\x40\x05\xec\x0c\xaf\x3f\x2c\x6f"
+	"\x2c\xe8\xbf\x1d\xee\xd0\xb3\xef\x7c\x5b\x9e\x88\x4f\x2a\x8b\x0e"
+	"\x4a\xbd\xb7\x8c\xfa\x10\x0e\x3b\xda\x68\xad\x41\x2b\xe4\x96\xfa"
+	"\x7f\x80\x52\x5f\x07\x9f\x0e\x3b\x5e\x96\x45\x1a\x13\x2b\x94\xce"
+	"\x1f\x07\x69\x85\x35\xfc\x69\x63\x5b\xf8\xf8\x3f\xce\x9d\x40\x1e"
+	"\x7c\xad\xfb\x9e\xce\xe0\x01\xf8\xef\x59\x5d\xdc\x00\x79\xab\x8a"
+	"\x3f\x80\xa2\x76\x32\x94\xa9\xea\x65\x02\x81\x81\x00\xf1\x38\x60"
+	"\x90\x0d\x0c\x2e\x3d\x34\xe5\x90\xea\x21\x43\x1f\x68\x63\x16\x7b"
+	"\x25\x8d\xde\x82\x2b\x52\xf8\xa3\xfd\x0f\x39\xe7\xe9\x5e\x32\x75"
+	"\x15\x7d\xd0\xc9\xce\x06\xe5\xfb\xa9\xcb\x22\xe5\xdb\x49\x09\xf2"
+	"\xe6\xb7\xa5\xa7\x75\x2e\x91\x2d\x2b\x5d\xf1\x48\x61\x45\x43\xd7"
+	"\xbd\xfc\x11\x73\xb5\x11\x9f\xb2\x18\x3a\x6f\x36\xa7\xc2\xd3\x18"
+	"\x4d\xf0\xc5\x1f\x70\x8c\x9b\xc5\x1d\x95\xa8\x5a\x9e\x8c\xb1\x4b"
+	"\x6a\x2a\x84\x76\x2c\xd8\x4f\x47\xb0\x81\x84\x02\x45\xf0\x85\xf8"
+	"\x0c\x6d\xa7\x0c\x4d\x2c\xb2\x5b\x81\x70\xfd\x6e\x17\x02\x81\x81"
+	"\x00\x8d\x07\xc5\xfa\x92\x4f\x48\xcb\xd3\xdd\xfe\x02\x4c\xa1\x7f"
+	"\x6d\xab\xfc\x38\xe7\x9b\x95\xcf\xfe\x49\x51\xc6\x09\xf7\x2b\xa8"
+	"\x94\x15\x54\x75\x9d\x88\xb4\x05\x55\xc3\xcd\xd4\x4a\xe4\x08\x53"
+	"\xc8\x09\xbd\x0c\x4d\x83\x65\x75\x85\xbc\x5e\xf8\x2a\xbd\xe2\x5d"
+	"\x1d\x16\x0e\xf9\x34\x89\x38\xaf\x34\x36\x6c\x2c\x22\x44\x22\x81"
+	"\x90\x73\xd9\xea\x3a\xaf\x70\x74\x48\x7c\xc6\xb5\xb0\xdc\xe5\xa9"
+	"\xa8\x76\x4b\xbc\xf7\x00\xf3\x4c\x22\x0f\x44\x62\x1d\x40\x0a\x57"
+	"\xe2\x5b\xdd\x7c\x7b\x9a\xad\xda\x70\x52\x21\x8a\x4c\xc2\xc3\x98"
+	"\x75\x02\x81\x81\x00\xed\x24\x5c\xa2\x21\x81\xa1\x0f\xa1\x2a\x33"
+	"\x0e\x49\xc7\x00\x60\x92\x51\x6e\x9d\x9b\xdc\x6d\x22\x04\x7e\xd6"
+	"\x51\x19\x9f\xf6\xe3\x91\x2c\x8f\xb8\xa2\x29\x19\xcc\x47\x31\xdf"
+	"\xf8\xab\xf0\xd2\x02\x83\xca\x99\x16\xc2\xe2\xc3\x3f\x4b\x99\x83"
+	"\xcb\x87\x9e\x86\x66\xc2\x3e\x91\x21\x80\x66\xf3\xd6\xc5\xcd\xb6"
+	"\xbb\x64\xef\x22\xcf\x48\x94\x58\xe7\x7e\xd5\x7c\x34\x1c\xb7\xa2"
+	"\xd0\x93\xe9\x9f\xb5\x11\x61\xd7\x5f\x37\x0f\x64\x52\x70\x11\x78"
+	"\xcc\x08\x77\xeb\xf8\x30\x1e\xb4\x9e\x1b\x4a\xc7\xa8\x33\x51\xe0"
+	"\xed\xdf\x53\xf6\xdf\x02\x81\x81\x00\x86\xd9\x4c\xee\x65\x61\xc1"
+	"\x19\xa9\xd5\x74\x9b\xd5\xca\xf6\x83\x2b\x06\xb4\x20\xfe\x45\x29"
+	"\xe8\xe3\xfa\xe1\x4f\x28\x8e\x63\x2f\x74\xc3\x3a\x5c\x9a\xf5\x9e"
+	"\x0e\x0d\xc5\xfe\xa0\x4c\x00\xce\x7b\xa4\x19\x17\x59\xaf\x13\x3a"
+	"\x03\x8f\x54\xf5\x60\x39\x2e\xd9\x06\xb3\x7c\xd6\x90\x06\x41\x77"
+	"\xf3\x93\xe1\x7a\x01\x41\xc1\x8f\xfe\x4c\x88\x39\xdb\xde\x71\x9e"
+	"\x58\xd1\x49\x50\x80\xb2\x5a\x4f\x69\x8b\xb8\xfe\x63\xd4\x42\x3d"
+	"\x37\x61\xa8\x4c\xff\xb6\x99\x4c\xf4\x51\xe0\x44\xaa\x69\x79\x3f"
+	"\x81\xa4\x61\x3d\x26\xe9\x04\x52\x64",
+	.key_len = 1193,
 	/*
 	 * m is SHA256 hash of following message:
 	 * "\x49\x41\xbe\x0a\x0c\xc9\xf6\x35\x51\xe4\x27\x56\x13\x71\x4b\xd0"
@@ -32583,221 +32686,4 @@
 			  0xae, 0x15, 0x81, 0x15, 0xd0, 0x88, 0xa0, 0x3c, },
 }};
 
-static const struct hash_testvec blakes2s_128_tv_template[] = {{
-	.digest = (u8[]){ 0x64, 0x55, 0x0d, 0x6f, 0xfe, 0x2c, 0x0a, 0x01,
-			  0xa1, 0x4a, 0xba, 0x1e, 0xad, 0xe0, 0x20, 0x0c, },
-}, {
-	.plaintext = blake2_ordered_sequence,
-	.psize = 64,
-	.digest = (u8[]){ 0xdc, 0x66, 0xca, 0x8f, 0x03, 0x86, 0x58, 0x01,
-			  0xb0, 0xff, 0xe0, 0x6e, 0xd8, 0xa1, 0xa9, 0x0e, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 1,
-	.digest = (u8[]){ 0x88, 0x1e, 0x42, 0xe7, 0xbb, 0x35, 0x80, 0x82,
-			  0x63, 0x7c, 0x0a, 0x0f, 0xd7, 0xec, 0x6c, 0x2f, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 7,
-	.digest = (u8[]){ 0xcf, 0x9e, 0x07, 0x2a, 0xd5, 0x22, 0xf2, 0xcd,
-			  0xa2, 0xd8, 0x25, 0x21, 0x80, 0x86, 0x73, 0x1c, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.plaintext = blake2_ordered_sequence,
-	.psize = 15,
-	.digest = (u8[]){ 0xf6, 0x33, 0x5a, 0x2c, 0x22, 0xa0, 0x64, 0xb2,
-			  0xb6, 0x3f, 0xeb, 0xbc, 0xd1, 0xc3, 0xe5, 0xb2, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 247,
-	.digest = (u8[]){ 0x72, 0x66, 0x49, 0x60, 0xf9, 0x4a, 0xea, 0xbe,
-			  0x1f, 0xf4, 0x60, 0xce, 0xb7, 0x81, 0xcb, 0x09, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 256,
-	.digest = (u8[]){ 0xd5, 0xa4, 0x0e, 0xc3, 0x16, 0xc7, 0x51, 0xa6,
-			  0x3c, 0xd0, 0xd9, 0x11, 0x57, 0xfa, 0x1e, 0xbb, },
-}};
-
-static const struct hash_testvec blakes2s_160_tv_template[] = {{
-	.plaintext = blake2_ordered_sequence,
-	.psize = 7,
-	.digest = (u8[]){ 0xb4, 0xf2, 0x03, 0x49, 0x37, 0xed, 0xb1, 0x3e,
-			  0x5b, 0x2a, 0xca, 0x64, 0x82, 0x74, 0xf6, 0x62,
-			  0xe3, 0xf2, 0x84, 0xff, },
-}, {
-	.plaintext = blake2_ordered_sequence,
-	.psize = 256,
-	.digest = (u8[]){ 0xaa, 0x56, 0x9b, 0xdc, 0x98, 0x17, 0x75, 0xf2,
-			  0xb3, 0x68, 0x83, 0xb7, 0x9b, 0x8d, 0x48, 0xb1,
-			  0x9b, 0x2d, 0x35, 0x05, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.digest = (u8[]){ 0x50, 0x16, 0xe7, 0x0c, 0x01, 0xd0, 0xd3, 0xc3,
-			  0xf4, 0x3e, 0xb1, 0x6e, 0x97, 0xa9, 0x4e, 0xd1,
-			  0x79, 0x65, 0x32, 0x93, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 1,
-	.digest = (u8[]){ 0x1c, 0x2b, 0xcd, 0x9a, 0x68, 0xca, 0x8c, 0x71,
-			  0x90, 0x29, 0x6c, 0x54, 0xfa, 0x56, 0x4a, 0xef,
-			  0xa2, 0x3a, 0x56, 0x9c, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 15,
-	.digest = (u8[]){ 0x36, 0xc3, 0x5f, 0x9a, 0xdc, 0x7e, 0xbf, 0x19,
-			  0x68, 0xaa, 0xca, 0xd8, 0x81, 0xbf, 0x09, 0x34,
-			  0x83, 0x39, 0x0f, 0x30, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.plaintext = blake2_ordered_sequence,
-	.psize = 64,
-	.digest = (u8[]){ 0x86, 0x80, 0x78, 0xa4, 0x14, 0xec, 0x03, 0xe5,
-			  0xb6, 0x9a, 0x52, 0x0e, 0x42, 0xee, 0x39, 0x9d,
-			  0xac, 0xa6, 0x81, 0x63, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 247,
-	.digest = (u8[]){ 0x2d, 0xd8, 0xd2, 0x53, 0x66, 0xfa, 0xa9, 0x01,
-			  0x1c, 0x9c, 0xaf, 0xa3, 0xe2, 0x9d, 0x9b, 0x10,
-			  0x0a, 0xf6, 0x73, 0xe8, },
-}};
-
-static const struct hash_testvec blakes2s_224_tv_template[] = {{
-	.plaintext = blake2_ordered_sequence,
-	.psize = 1,
-	.digest = (u8[]){ 0x61, 0xb9, 0x4e, 0xc9, 0x46, 0x22, 0xa3, 0x91,
-			  0xd2, 0xae, 0x42, 0xe6, 0x45, 0x6c, 0x90, 0x12,
-			  0xd5, 0x80, 0x07, 0x97, 0xb8, 0x86, 0x5a, 0xfc,
-			  0x48, 0x21, 0x97, 0xbb, },
-}, {
-	.plaintext = blake2_ordered_sequence,
-	.psize = 247,
-	.digest = (u8[]){ 0x9e, 0xda, 0xc7, 0x20, 0x2c, 0xd8, 0x48, 0x2e,
-			  0x31, 0x94, 0xab, 0x46, 0x6d, 0x94, 0xd8, 0xb4,
-			  0x69, 0xcd, 0xae, 0x19, 0x6d, 0x9e, 0x41, 0xcc,
-			  0x2b, 0xa4, 0xd5, 0xf6, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.digest = (u8[]){ 0x32, 0xc0, 0xac, 0xf4, 0x3b, 0xd3, 0x07, 0x9f,
-			  0xbe, 0xfb, 0xfa, 0x4d, 0x6b, 0x4e, 0x56, 0xb3,
-			  0xaa, 0xd3, 0x27, 0xf6, 0x14, 0xbf, 0xb9, 0x32,
-			  0xa7, 0x19, 0xfc, 0xb8, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.plaintext = blake2_ordered_sequence,
-	.psize = 7,
-	.digest = (u8[]){ 0x73, 0xad, 0x5e, 0x6d, 0xb9, 0x02, 0x8e, 0x76,
-			  0xf2, 0x66, 0x42, 0x4b, 0x4c, 0xfa, 0x1f, 0xe6,
-			  0x2e, 0x56, 0x40, 0xe5, 0xa2, 0xb0, 0x3c, 0xe8,
-			  0x7b, 0x45, 0xfe, 0x05, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 15,
-	.digest = (u8[]){ 0x16, 0x60, 0xfb, 0x92, 0x54, 0xb3, 0x6e, 0x36,
-			  0x81, 0xf4, 0x16, 0x41, 0xc3, 0x3d, 0xd3, 0x43,
-			  0x84, 0xed, 0x10, 0x6f, 0x65, 0x80, 0x7a, 0x3e,
-			  0x25, 0xab, 0xc5, 0x02, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 64,
-	.digest = (u8[]){ 0xca, 0xaa, 0x39, 0x67, 0x9c, 0xf7, 0x6b, 0xc7,
-			  0xb6, 0x82, 0xca, 0x0e, 0x65, 0x36, 0x5b, 0x7c,
-			  0x24, 0x00, 0xfa, 0x5f, 0xda, 0x06, 0x91, 0x93,
-			  0x6a, 0x31, 0x83, 0xb5, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.plaintext = blake2_ordered_sequence,
-	.psize = 256,
-	.digest = (u8[]){ 0x90, 0x02, 0x26, 0xb5, 0x06, 0x9c, 0x36, 0x86,
-			  0x94, 0x91, 0x90, 0x1e, 0x7d, 0x2a, 0x71, 0xb2,
-			  0x48, 0xb5, 0xe8, 0x16, 0xfd, 0x64, 0x33, 0x45,
-			  0xb3, 0xd7, 0xec, 0xcc, },
-}};
-
-static const struct hash_testvec blakes2s_256_tv_template[] = {{
-	.plaintext = blake2_ordered_sequence,
-	.psize = 15,
-	.digest = (u8[]){ 0xd9, 0x7c, 0x82, 0x8d, 0x81, 0x82, 0xa7, 0x21,
-			  0x80, 0xa0, 0x6a, 0x78, 0x26, 0x83, 0x30, 0x67,
-			  0x3f, 0x7c, 0x4e, 0x06, 0x35, 0x94, 0x7c, 0x04,
-			  0xc0, 0x23, 0x23, 0xfd, 0x45, 0xc0, 0xa5, 0x2d, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.digest = (u8[]){ 0x48, 0xa8, 0x99, 0x7d, 0xa4, 0x07, 0x87, 0x6b,
-			  0x3d, 0x79, 0xc0, 0xd9, 0x23, 0x25, 0xad, 0x3b,
-			  0x89, 0xcb, 0xb7, 0x54, 0xd8, 0x6a, 0xb7, 0x1a,
-			  0xee, 0x04, 0x7a, 0xd3, 0x45, 0xfd, 0x2c, 0x49, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.plaintext = blake2_ordered_sequence,
-	.psize = 1,
-	.digest = (u8[]){ 0x22, 0x27, 0xae, 0xaa, 0x6e, 0x81, 0x56, 0x03,
-			  0xa7, 0xe3, 0xa1, 0x18, 0xa5, 0x9a, 0x2c, 0x18,
-			  0xf4, 0x63, 0xbc, 0x16, 0x70, 0xf1, 0xe7, 0x4b,
-			  0x00, 0x6d, 0x66, 0x16, 0xae, 0x9e, 0x74, 0x4e, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 7,
-	.digest = (u8[]){ 0x58, 0x5d, 0xa8, 0x60, 0x1c, 0xa4, 0xd8, 0x03,
-			  0x86, 0x86, 0x84, 0x64, 0xd7, 0xa0, 0x8e, 0x15,
-			  0x2f, 0x05, 0xa2, 0x1b, 0xbc, 0xef, 0x7a, 0x34,
-			  0xb3, 0xc5, 0xbc, 0x4b, 0xf0, 0x32, 0xeb, 0x12, },
-}, {
-	.ksize = 32,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 64,
-	.digest = (u8[]){ 0x89, 0x75, 0xb0, 0x57, 0x7f, 0xd3, 0x55, 0x66,
-			  0xd7, 0x50, 0xb3, 0x62, 0xb0, 0x89, 0x7a, 0x26,
-			  0xc3, 0x99, 0x13, 0x6d, 0xf0, 0x7b, 0xab, 0xab,
-			  0xbd, 0xe6, 0x20, 0x3f, 0xf2, 0x95, 0x4e, 0xd4, },
-}, {
-	.ksize = 1,
-	.key = "B",
-	.plaintext = blake2_ordered_sequence,
-	.psize = 247,
-	.digest = (u8[]){ 0x2e, 0x74, 0x1c, 0x1d, 0x03, 0xf4, 0x9d, 0x84,
-			  0x6f, 0xfc, 0x86, 0x32, 0x92, 0x49, 0x7e, 0x66,
-			  0xd7, 0xc3, 0x10, 0x88, 0xfe, 0x28, 0xb3, 0xe0,
-			  0xbf, 0x50, 0x75, 0xad, 0x8e, 0xa4, 0xe6, 0xb2, },
-}, {
-	.ksize = 16,
-	.key = blake2_ordered_sequence,
-	.plaintext = blake2_ordered_sequence,
-	.psize = 256,
-	.digest = (u8[]){ 0xb9, 0xd2, 0x81, 0x0e, 0x3a, 0xb1, 0x62, 0x9b,
-			  0xad, 0x44, 0x05, 0xf4, 0x92, 0x2e, 0x99, 0xc1,
-			  0x4a, 0x47, 0xbb, 0x5b, 0x6f, 0xb2, 0x96, 0xed,
-			  0xd5, 0x06, 0xb5, 0x3a, 0x7c, 0x7a, 0x65, 0x1d, },
-}};
-
 #endif	/* _CRYPTO_TESTMGR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/xor.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/xor.c
@@ -83,33 +83,30 @@
 do_xor_speed(struct xor_block_template *tmpl, void *b1, void *b2)
 {
 	int speed;
-	int i, j;
-	ktime_t min, start, diff;
+	unsigned long reps;
+	ktime_t min, start, t0;
 
 	tmpl->next = template_list;
 	template_list = tmpl;
 
 	preempt_disable();
 
-	min = (ktime_t)S64_MAX;
-	for (i = 0; i < 3; i++) {
-		start = ktime_get();
-		for (j = 0; j < REPS; j++) {
-			mb(); /* prevent loop optimization */
-			tmpl->do_2(BENCH_SIZE, b1, b2);
-			mb();
-		}
-		diff = ktime_sub(ktime_get(), start);
-		if (diff < min)
-			min = diff;
-	}
+	reps = 0;
+	t0 = ktime_get();
+	/* delay start until time has advanced */
+	while ((start = ktime_get()) == t0)
+		cpu_relax();
+	do {
+		mb(); /* prevent loop optimization */
+		tmpl->do_2(BENCH_SIZE, b1, b2);
+		mb();
+	} while (reps++ < REPS || (t0 = ktime_get()) == start);
+	min = ktime_sub(t0, start);
 
 	preempt_enable();
 
 	// bytes/ns == GB/s, multiply by 1000 to get MB/s [not MiB/s]
-	if (!min)
-		min = 1;
-	speed = (1000 * REPS * BENCH_SIZE) / (unsigned int)ktime_to_ns(min);
+	speed = (1000 * reps * BENCH_SIZE) / (unsigned int)ktime_to_ns(min);
 	tmpl->speed = speed;
 
 	pr_info("   %-16s: %5d MB/sec\n", tmpl->name, speed);
--- linux-xilinx-zynqmp-5.15.0.orig/crypto/xts.c
+++ linux-xilinx-zynqmp-5.15.0/crypto/xts.c
@@ -203,12 +203,12 @@
 	if (!err) {
 		struct xts_request_ctx *rctx = skcipher_request_ctx(req);
 
-		rctx->subreq.base.flags &= ~CRYPTO_TFM_REQ_MAY_SLEEP;
+		rctx->subreq.base.flags &= CRYPTO_TFM_REQ_MAY_BACKLOG;
 		err = xts_xor_tweak_post(req, true);
 
 		if (!err && unlikely(req->cryptlen % XTS_BLOCK_SIZE)) {
 			err = xts_cts_final(req, crypto_skcipher_encrypt);
-			if (err == -EINPROGRESS)
+			if (err == -EINPROGRESS || err == -EBUSY)
 				return;
 		}
 	}
@@ -223,12 +223,12 @@
 	if (!err) {
 		struct xts_request_ctx *rctx = skcipher_request_ctx(req);
 
-		rctx->subreq.base.flags &= ~CRYPTO_TFM_REQ_MAY_SLEEP;
+		rctx->subreq.base.flags &= CRYPTO_TFM_REQ_MAY_BACKLOG;
 		err = xts_xor_tweak_post(req, false);
 
 		if (!err && unlikely(req->cryptlen % XTS_BLOCK_SIZE)) {
 			err = xts_cts_final(req, crypto_skcipher_decrypt);
-			if (err == -EINPROGRESS)
+			if (err == -EINPROGRESS || err == -EBUSY)
 				return;
 		}
 	}
@@ -396,10 +396,10 @@
 	 * cipher name.
 	 */
 	if (!strncmp(cipher_name, "ecb(", 4)) {
-		unsigned len;
+		int len;
 
-		len = strlcpy(ctx->name, cipher_name + 4, sizeof(ctx->name));
-		if (len < 2 || len >= sizeof(ctx->name))
+		len = strscpy(ctx->name, cipher_name + 4, sizeof(ctx->name));
+		if (len < 2)
 			goto err_free_inst;
 
 		if (ctx->name[len - 1] != ')')
@@ -466,3 +466,4 @@
 MODULE_DESCRIPTION("XTS block cipher mode");
 MODULE_ALIAS_CRYPTO("xts");
 MODULE_IMPORT_NS(CRYPTO_INTERNAL);
+MODULE_SOFTDEP("pre: ecb");
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/changelog
+++ linux-xilinx-zynqmp-5.15.0/debian.master/changelog
@@ -0,0 +1,46702 @@
+linux (5.15.0-142.152) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-142.152 -proposed tracker (LP: #2110829)
+
+  * Rotate the Canonical Livepatch key (LP: #2111244)
+    - [Config] Prepare for Canonical Livepatch key rotation
+
+  * Jammy generic-64k fails to initialize gVNIC devices (LP: #2109537)
+    - gve: Perform adminq allocations through a dma_pool.
+    - gve: Deprecate adminq_pfn for pci revision 0x1.
+    - gve: Remove obsolete checks that rely on page size.
+    - gve: Add page size register to the register_page_list command.
+    - gve: Remove dependency on 4k page size.
+
+  * CVE-2025-2312 cifs.upcall could access incorrect kerberos credentials cache
+    (LP: #2099914) // CVE-2025-2312
+    - CIFS: New mount option for cifs.upcall namespace resolution
+
+  * [UBUNTU 22.04] net/smc: fix neighbour and rtable leak in smc_ib_find_route()
+    (LP: #2109601) // CVE-2024-36945
+    - net/smc: fix neighbour and rtable leak in smc_ib_find_route()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355)
+    - clockevents/drivers/i8253: Fix stop sequence for timer 0
+    - sched/isolation: Prevent boot crash when the boot CPU is nohz_full
+    - fbdev: hyperv_fb: iounmap() the correct memory when removing a device
+    - pinctrl: bcm281xx: Fix incorrect regmap max_registers value
+    - netfilter: nft_ct: Use __refcount_inc() for per-CPU nft_ct_pcpu_template.
+    - net: dsa: mv88e6xxx: Verify after ATU Load ops
+    - netpoll: hold rcu read lock in __netpoll_send_skb()
+    - Drivers: hv: vmbus: Don't release fb_mmio resource in vmbus_free_mmio()
+    - ipvs: prevent integer overflow in do_ip_vs_get_ctl()
+    - netfilter: nft_exthdr: fix offset with ipv4_find_option()
+    - gre: Fix IPv6 link-local address generation.
+    - slab: clean up function prototypes
+    - slab: Introduce kmalloc_size_roundup()
+    - openvswitch: Use kmalloc_size_roundup() to match ksize() usage
+    - net: openvswitch: remove misbehaving actions length check
+    - net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices
+    - nvme-fc: go straight to connecting state when initializing
+    - hrtimers: Mark is_migration_base() with __always_inline
+    - powercap: call put_device() on an error path in
+      powercap_register_control_type()
+    - scsi: core: Use GFP_NOIO to avoid circular locking dependency
+    - ACPI: resource: IRQ override for Eluktronics MECH-17
+    - alpha/elf: Fix misc/setarch test of util-linux by removing 32bit support
+    - vboxsf: fix building with GCC 15
+    - HID: intel-ish-hid: fix the length of MNG_SYNC_FW_CLOCK in doorbell
+    - sched: Clarify wake_up_q()'s write to task->wake_q.next
+    - s390/cio: Fix CHPID "configure" attribute caching
+    - thermal/cpufreq_cooling: Remove structure member documentation
+    - ASoC: rsnd: don't indicate warning on rsnd_kctrl_accept_runtime()
+    - ASoC: arizona/madera: use fsleep() in up/down DAPM event delays.
+    - ASoC: SOF: Intel: hda: add softdep pre to snd-hda-codec-hdmi module
+    - net: wwan: mhi_wwan_mbim: Silence sequence number glitch errors
+    - nvmet-rdma: recheck queue state is LIVE in state lock in recv done
+    - sctp: Fix undefined behavior in left shift operation
+    - nvme: only allow entering LIVE from CONNECTING state
+    - ASoC: tas2770: Fix volume scale
+    - ASoC: tas2764: Fix power control mask
+    - ASoC: tas2764: Set the SDOUT polarity correctly
+    - fuse: don't truncate cached, mutated symlink
+    - x86/irq: Define trace events conditionally
+    - mptcp: safety check before fallback
+    - drm/nouveau: Do not override forced connector status
+    - block: fix 'kmem_cache of name 'bio-108' already exists'
+    - USB: serial: ftdi_sio: add support for Altera USB Blaster 3
+    - USB: serial: option: add Telit Cinterion FE990B compositions
+    - USB: serial: option: fix Telit Cinterion FE990A name
+    - USB: serial: option: match on interface class for Telit FN990B
+    - drm/atomic: Filter out redundant DPMS calls
+    - drm/amd/display: Restore correct backlight brightness after a GPU reset
+    - qlcnic: fix memory leak issues in qlcnic_sriov_common.c
+    - lib/buildid: Handle memfd_secret() files in build_id_parse()
+    - tcp: fix races in tcp_abort()
+    - ASoC: ops: Consistently treat platform_max as control value
+    - drm/gma500: Add NULL check for pci_gfx_root in mid_get_vbt_data()
+    - ASoC: codecs: wm0010: Fix error handling path in wm0010_spi_probe()
+    - cifs: Fix integer overflow while processing actimeo mount option
+    - i2c: ali1535: Fix an error handling path in ali1535_probe()
+    - i2c: ali15x3: Fix an error handling path in ali15x3_probe()
+    - i2c: sis630: Fix an error handling path in sis630_probe()
+    - drm/amd/display: Check for invalid input params when building scaling params
+    - smb: client: Fix match_session bug preventing session reuse
+    - Revert "smb: client: fix potential UAF in cifs_debug_files_proc_show()"
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+    - firmware: imx-scu: fix OF node leak in .probe()
+    - xfrm_output: Force software GSO only in tunnel mode
+    - ARM: dts: bcm2711: PL011 UARTs are actually r1p5
+    - RDMA/bnxt_re: Add missing paranthesis in map_qp_id_to_tbl_indx
+    - ARM: dts: bcm2711: Don't mark timer regs unconfigured
+    - RDMA/bnxt_re: Avoid clearing VLAN_ID mask in modify qp path
+    - RDMA/hns: Remove redundant 'phy_addr' in hns_roce_hem_list_find_mtt()
+    - RDMA/hns: Fix unmatched condition in error path of alloc_user_qp_db()
+    - RDMA/hns: Fix a missing rollback in error path of
+      hns_roce_create_qp_common()
+    - RDMA/hns: Fix wrong value of max_sge_rd
+    - ipv6: Set errno after ip_fib_metrics_init() in ip6_route_info_create().
+    - net/neighbor: add missing policy for NDTPA_QUEUE_LENBYTES
+    - Revert "gre: Fix IPv6 link-local address generation."
+    - i2c: omap: fix IRQ storms
+    - drm/v3d: Don't run jobs that have errors flagged in its fence
+    - mmc: atmel-mci: Add missing clk_disable_unprepare()
+    - ARM: shmobile: smp: Enforce shmobile_smp_* alignment
+    - batman-adv: Ignore own maximum aggregation size during RX
+    - drm/amdgpu: Fix JPEG video caps max size for navi1x and raven
+    - mptcp: Fix data stream corruption in the address announcement
+    - arm64: dts: rockchip: fix u2phy1_host status for NanoPi R4S
+    - ALSA: usb-audio: Add quirk for Plantronics headsets to fix control names
+    - HID: hid-plantronics: Add mic mute mapping and generalize quirks
+    - ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed()
+    - ARM: 9351/1: fault: Add "cut here" line for prefetch aborts
+    - ARM: Remove address checking for MMUless devices
+    - ALSA: hda/realtek: Support mute LED on HP Laptop 15s-du3xxx
+    - counter: stm32-lptimer-cnt: fix error handling when enabling
+    - counter: microchip-tcb-capture: Fix undefined counter channel state on probe
+    - tty: serial: 8250: Add some more device IDs
+    - tty: serial: 8250: Add Brainboxes XC devices
+    - net: usb: qmi_wwan: add Telit Cinterion FN990B composition
+    - net: usb: qmi_wwan: add Telit Cinterion FE990B composition
+    - net: usb: usbnet: restore usb%d name exception for local mac addresses
+    - serial: 8250_dma: terminate correct DMA in tx_dma_flush()
+    - x86/mm/pat: cpa-test: fix length for CPA_ARRAY test
+    - cpufreq: scpi: compare kHz instead of Hz
+    - cpufreq: governor: Fix negative 'idle_time' handling in dbs_update()
+    - x86/fpu: Avoid copying dynamic FP state from init_task in
+      arch_dup_task_struct()
+    - x86/platform: Only allow CONFIG_EISA for 32-bit
+    - [Config] updateconfigs for HAVE_EISA
+    - PM: sleep: Adjust check before setting power.must_resume
+    - selinux: Chain up tool resolving errors in install_policy.sh
+    - EDAC/ie31200: Fix the size of EDAC_MC_LAYER_CHIP_SELECT layer
+    - EDAC/ie31200: Fix the DIMM size mask for several SoCs
+    - EDAC/ie31200: Fix the error path order of ie31200_init()
+    - PM: sleep: Fix handling devices with direct_complete set on errors
+    - lockdep: Don't disable interrupts on RT in disable_irq_nosync_lockdep.*()
+    - perf/ring_buffer: Allow the EPOLLRDNORM flag for poll
+    - media: platform: allgro-dvt: unregister v4l2_device on the error path
+    - HID: remove superfluous (and wrong) Makefile entry for
+      CONFIG_INTEL_ISH_FIRMWARE_DOWNLOADER
+    - ALSA: hda/realtek: Always honor no_shutup_pins
+    - ASoC: ti: j721e-evm: Fix clock configuration for ti,j7200-cpb-audio
+      compatible
+    - drm/bridge: ti-sn65dsi86: Fix multiple instances
+    - drm/dp_mst: Fix drm RAD print
+    - drm: xlnx: zynqmp: Fix max dma segment size
+    - drm/mediatek: mtk_hdmi: Unregister audio platform device on failure
+    - drm/mediatek: mtk_hdmi: Fix typo for aud_sampe_size member
+    - PCI: cadence-ep: Fix the driver to send MSG TLP for INTx without data
+      payload
+    - PCI: brcmstb: Use internal register to change link capability
+    - PCI/portdrv: Only disable pciehp interrupts early when needed
+    - PCI: Avoid reset when disabled via sysfs
+    - drm/amd/display: fix type mismatch in CalculateDynamicMetadataParameters()
+    - PCI: Remove stray put_device() in pci_register_host_bridge()
+    - PCI: xilinx-cpm: Fix IRQ domain leak in error path of probe
+    - drm/mediatek: dsi: fix error codes in mtk_dsi_host_transfer()
+    - PCI: pciehp: Don't enable HPIE when resuming in poll mode
+    - fbdev: au1100fb: Move a variable assignment behind a null pointer check
+    - mdacon: rework dependency list
+    - fbdev: sm501fb: Add some geometry checks.
+    - clk: amlogic: gxbb: drop incorrect flag on 32k clock
+    - crypto: hisilicon/sec2 - fix for aead authsize alignment
+    - of: property: Increase NR_FWNODE_REFERENCE_ARGS
+    - remoteproc: qcom_q6v5_pas: Make single-PD handling more robust
+    - libbpf: Fix hypothetical STT_SECTION extern NULL deref case
+    - clk: qcom: gcc-msm8953: fix stuck venus0_core0 clock
+    - bpf: Use preempt_count() directly in bpf_send_signal_common()
+    - lib: 842: Improve error handling in sw842_compress()
+    - pinctrl: renesas: rza2: Fix missing of_node_put() call
+    - pinctrl: renesas: rzg2l: Fix missing of_node_put() call
+    - clk: rockchip: rk3328: fix wrong clk_ref_usb3otg parent
+    - remoteproc: qcom_q6v5_mss: Handle platforms with one power domain
+    - IB/mad: Check available slots before posting receive WRs
+    - pinctrl: tegra: Set SFIO mode to Mux Register
+    - clk: amlogic: g12b: fix cluster A parent data
+    - clk: amlogic: gxbb: drop non existing 32k clock parent
+    - clk: amlogic: g12a: fix mmc A peripheral clock
+    - x86/entry: Fix ORC unwinder for PUSH_REGS with save_ret=1
+    - power: supply: max77693: Fix wrong conversion of charge input threshold
+      value
+    - crypto: nx - Fix uninitialised hv_nxc on error
+    - mfd: sm501: Switch to BIT() to mitigate integer overflows
+    - x86/dumpstack: Fix inaccurate unwinding from exception stacks due to
+      misplaced assignment
+    - crypto: hisilicon/sec2 - fix for aead auth key length
+    - clk: qcom: mmcc-sdm660: fix stuck video_subcore0 clock
+    - isofs: fix KMSAN uninit-value bug in do_isofs_readdir()
+    - soundwire: slave: fix an OF node reference leak in soundwire slave device
+    - coresight: catu: Fix number of pages while using 64k pages
+    - iio: accel: mma8452: Ensure error return on failure to matching oversampling
+      ratio
+    - iio: adc: ad7124: Fix comparison of channel configs
+    - perf units: Fix insufficient array space
+    - kexec: initialize ELF lowest address to ULONG_MAX
+    - NFSv4: Don't trigger uneccessary scans for return-on-close delegations
+    - fuse: fix dax truncate/punch_hole fault path
+    - i3c: master: svc: Fix missing the IBI rules
+    - perf python: Fixup description of sample.id event member
+    - perf python: Decrement the refcount of just created event on failure
+    - perf python: Don't keep a raw_data pointer to consumed ring buffer space
+    - perf python: Check if there is space to copy all the event
+    - fs/procfs: fix the comment above proc_pid_wchan()
+    - objtool, media: dib8000: Prevent divide-by-zero in dib8000_set_dds()
+    - exfat: fix the infinite loop in exfat_find_last_cluster()
+    - ksmbd: fix multichannel connection failure
+    - ring-buffer: Fix bytes_dropped calculation issue
+    - ACPI: processor: idle: Return an error if both P_LVL{2,3} idle states are
+      invalid
+    - octeontx2-af: Fix mbox INTR handler when num VFs > 64
+    - octeontx2-af: Free NIX_AF_INT_VEC_GEN irq
+    - sched/smt: Always inline sched_smt_active()
+    - wifi: iwlwifi: fw: allocate chained SG tables for dump
+    - nvme-tcp: fix possible UAF in nvme_tcp_poll
+    - nvme-pci: clean up CMBMSC when registering CMB fails
+    - nvme-pci: skip CMB blocks incompatible with PCI P2P DMA
+    - affs: generate OFS sequence numbers starting at 1
+    - affs: don't write overlarge OFS data block size fields
+    - sched/deadline: Use online cpus for validating runtime
+    - locking/semaphore: Use wake_q to wake up processes outside lock critical
+      section
+    - x86/sgx: Warn explicitly if X86_FEATURE_SGX_LC is not enabled
+    - drm/amd: Keep display off while going into S4
+    - ALSA: hda/realtek: Add mute LED quirk for HP Pavilion x360 14-dy1xxx
+    - can: statistics: use atomic access in hot path
+    - hwmon: (nct6775-core) Fix out of bounds access for NCT679{8,9}
+    - riscv: ftrace: Add parentheses in macro definitions of make_call_t0 and
+      make_call_ra
+    - ntb: intel: Fix using link status DB's
+    - netfilter: nft_set_hash: GC reaps elements with conncount for dynamic sets
+      only
+    - vsock: avoid timeout during connect() if the socket is closing
+    - tunnels: Accept PACKET_HOST in skb_tunnel_check_pmtu().
+    - ipv6: fix omitted netlink attributes when using RTEXT_FILTER_SKIP_STATS
+    - can: flexcan: only change CAN state when link up in system PM
+    - can: flexcan: disable transceiver during system PM
+    - mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0
+    - mmc: sdhci-brcmstb: add cqhci suspend/resume to PM ops
+    - tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
+    - tty: serial: fsl_lpuart: disable transmitter before changing RS485 related
+      registers
+    - platform/x86: ISST: Correct command storage data length
+    - ntb_perf: Delete duplicate dmaengine_unmap_put() call in perf_copy_chunk()
+    - x86/tsc: Always save/restore TSC sched_clock() on suspend/resume
+    - ACPI: resource: Skip IRQ override on ASUS Vivobook 14 X1404VAP
+    - mmc: sdhci-pxav3: set NEED_RSP_BUSY capability
+    - tracing: Ensure module defining synth event cannot be unloaded while tracing
+    - tracing: Fix synth event printk format for str fields
+    - tracing/osnoise: Fix possible recursive locking for cpus_read_lock()
+    - ext4: don't over-report free space or inodes in statvfs
+    - jfs: add index corruption check to DT_GETPAGE()
+    - NFSD: Skip sending CB_RECALL_ANY when the backchannel isn't up
+    - mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
+    - mm, slab: remove duplicate kernel-doc comment for ksize()
+    - tracing: Do not use PERF enums when perf is not defined
+    - mmc: sdhci-brcmstb: Initialize base_clk to NULL in sdhci_brcmstb_probe()
+    - Linux 5.15.180
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22025
+    - nfsd: put dl_stid if fail to queue dl_recall
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-39735
+    - jfs: fix slab-out-of-bounds read in ea_get()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-37785
+    - ext4: fix OOB read when checking dotdot dir
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22035
+    - tracing: Fix use-after-free in print_graph_function_flags during tracer
+      switching
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22044
+    - acpi: nfit: fix narrowing conversion in acpi_nfit_ctl
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22045
+    - x86/mm: Fix flush_tlb_range() when used for zapping normal PMDs
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46753
+    - btrfs: handle errors from btrfs_dec_ref() properly
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22050
+    - usbnet:fix NPE during rx_complete
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46812
+    - drm/amd/display: Skip inactive planes within
+      ModeSupportAndSystemConfiguration
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46821
+    - drm/amd/pm: Fix negative array index read
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22054
+    - arcnet: Add NULL check in com20020pci_probe()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22055
+    - net: fix geneve_opt length integer overflow
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22056
+    - netfilter: nft_tunnel: fix geneve_opt type confusion addition
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22060
+    - net: mvpp2: Prevent parser TCAM memory corruption
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38637
+    - net_sched: skbprio: Remove overly strict queue assertions
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22063
+    - netlabel: Fix NULL pointer exception caused by CALIPSO on IPv4 sockets
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22066
+    - ASoC: imx-card: Add NULL check in imx_card_probe()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2023-53034
+    - ntb_hw_switchtec: Fix shift-out-of-bounds in switchtec_ntb_mw_set_trans
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22071
+    - spufs: fix a leak in spufs_create_context()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22073
+    - spufs: fix a leak on spufs_new_file() failure
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21994
+    - ksmbd: fix incorrect validation for num_aces field of smb_acl
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38575
+    - ksmbd: use aead_request_free to match aead_request_alloc
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22075
+    - rtnetlink: Allocate vfinfo size for VF GUIDs when supported
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22079
+    - ocfs2: validate l_tree_depth to avoid out-of-bounds access
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22081
+    - fs/ntfs3: Fix a couple integer overflows on 32bit systems
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22086
+    - RDMA/mlx5: Fix mlx5_poll_one() cur_qp update flow
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22089
+    - RDMA/core: Don't expose hw_counters outside of init net namespace
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-39728
+    - clk: samsung: Fix UBSAN panic in samsung_clk_init()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38152
+    - remoteproc: core: Clear table_sz when rproc_shutdown
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-58093
+    - PCI/ASPM: Fix link state exit during switch upstream function removal
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22097
+    - drm/vkms: Fix use after free and double free on init error
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-23136
+    - thermal: int340x: Add NULL check for adev
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-23138
+    - watch_queue: fix pipe accounting mismatch
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22020
+    - memstick: rtsx_usb_ms: Fix slab-use-after-free in rtsx_usb_ms_drv_remove
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22021
+    - netfilter: socket: Lookup orig tuple for IPv6 SNAT
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22018
+    - atm: Fix NULL pointer dereference
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-56664
+    - bpf, sockmap: Fix race between element replace and close()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-53144 // CVE-2024-8805
+    - Bluetooth: hci_event: Align BR/EDR JUST_WORKS paring with LE
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21996
+    - drm/radeon: fix uninitialized size issue in radeon_vce_cs_parse()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22014
+    - soc: qcom: pdr: Fix the potential deadlock
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21999
+    - proc: fix UAF in proc_get_inode()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22008
+    - regulator: check that dummy regulator has been probed before using it
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22004
+    - net: atm: fix use after free in lec_send()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22005
+    - ipv6: Fix memleak of nhc_pcpu_rth_output in fib_check_nh_v6_gw().
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22007
+    - Bluetooth: Fix error code in chan_alloc_skb_cb()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22010
+    - RDMA/hns: Fix soft lockup during bt pages loop
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21941
+    - drm/amd/display: Fix null check for pipe_ctx->plane_state in
+      resource_build_scaling_params
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21962
+    - cifs: Fix integer overflow while processing closetimeo mount option
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21963
+    - cifs: Fix integer overflow while processing acdirmax mount option
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21964
+    - cifs: Fix integer overflow while processing acregmax mount option
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21968
+    - drm/amd/display: Fix slab-use-after-free on hdcp_work
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21956
+    - drm/amd/display: Assign normalized_pix_clk when color depth = 14
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21991
+    - x86/microcode/AMD: Fix out-of-bounds on systems with CPU-less NUMA nodes
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21992
+    - HID: ignore non-functional sensor in HP 5MP Camera
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21957
+    - scsi: qla1280: Fix kernel oops when debug level > 2
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21970
+    - net/mlx5: Bridge, fix the crash caused by LAG state check
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21959
+    - netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in
+      insert_tree()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21975
+    - net/mlx5: handle errors in mlx5_chains_create_table()
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21981
+    - ice: fix memory leak in aRFS after reset
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2022-49728
+    - ipv6: Fix signed integer overflow in __ip6_append_data
+
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2022-49636
+    - vlan: fix memory leak in vlan_newlink()
+
+  * VM boots slowly with large-BAR GPU Passthrough due to pci/probe.c redundancy
+    (LP: #2097389)
+    - PCI: Batch BAR sizing operations
+
+  * kexec fails in LPAR when some cpus are disabled (LP: #2075575)
+    - powerpc/pseries: Fix scv instruction crash with kexec
+
+  * CVE-2024-56608
+    - drm/amd/display: Fix out-of-bounds access in 'dcn21_link_encoder_create'
+
+  * CVE-2024-53168
+    - net: make sock_inuse_add() available
+    - sunrpc: fix one UAF issue caused by sunrpc kernel tcp socket
+
+  * CVE-2024-56551
+    - drm/amdgpu: fix usage slab after free
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Mon, 19 May 2025 12:17:06 +0200
+
+linux (5.15.0-140.150) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-140.150 -proposed tracker (LP: #2106996)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.04.14)
+
+  * NFS, overlay, fstab issue after update to kernel 5.15.0-133-generic and -134
+    (LP: #2103598)
+    - udf: Fix directory iteration for longer tail extents
+
+  * Remove floppy kernel module causes null pointer deference (LP: #2104326)
+    - floppy: fix add_disk() assumption on exit due to new developments
+
+  * CVE-2025-21971
+    - net_sched: Prevent creation of classes with TC_H_ROOT
+
+  * CVE-2024-56599
+    - wifi: ath10k: avoid NULL pointer error during sdio remove
+
+  * CVE-2024-56721
+    - x86/CPU/AMD: Terminate the erratum_1386_microcode array
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026)
+    - afs: Fix EEXIST error returned from afs_rmdir() to be ENOTEMPTY
+    - afs: Fix directory format encoding struct
+    - hung_task: move hung_task sysctl interface to hung_task.c
+    - sysctl: use const for typically used max/min proc sysctls
+    - sysctl: share unsigned long const values
+    - fs: move inode sysctls to its own file
+    - fs: move fs stat sysctls to file_table.c
+    - fs: fix proc_handler for sysctl_nr_open
+    - block: deprecate autoloading based on dev_t
+    - block: retry call probe after request_module in blk_request_module
+    - pstore/blk: trivial typo fixes
+    - nvme: Add error check for xa_store in nvme_get_effects_log
+    - partitions: ldm: remove the initial kernel-doc notation
+    - select: Fix unbalanced user_access_end()
+    - afs: Fix the fallback handling for the YFS.RemoveFile2 RPC call
+    - sched/psi: Use task->psi_flags to clear in CPU migration
+    - sched/fair: Fix value reported by hot tasks pulled in /proc/schedstat
+    - drm/etnaviv: Fix page property being used for non writecombine buffers
+    - genirq: Make handle_enforce_irqctx() unconditionally available
+    - wifi: rtlwifi: do not complete firmware loading needlessly
+    - wifi: rtlwifi: rtl8192se: rise completion of firmware loading as last step
+    - wifi: rtlwifi: wait for firmware loading before releasing memory
+    - wifi: rtlwifi: fix init_sw_vars leak when probe fails
+    - wifi: rtlwifi: usb: fix workqueue leak when probe fails
+    - spi: zynq-qspi: Add check for clk_enable()
+    - dt-bindings: mmc: controller: clarify the address-cells description
+    - spi: dt-bindings: add schema listing peripheral-specific properties
+    - dt-bindings: Another pass removing cases of 'allOf' containing a '$ref'
+    - dt-bindings: leds: Add Qualcomm Light Pulse Generator binding
+    - dt-bindings: leds: Optional multi-led unit address
+    - dt-bindings: leds: Add multicolor PWM LED bindings
+    - dt-bindings: leds: class-multicolor: reference class directly in multi-led
+      node
+    - dt-bindings: leds: class-multicolor: Fix path to color definitions
+    - rtlwifi: replace usage of found with dedicated list iterator variable
+    - wifi: rtlwifi: remove unused timer and related code
+    - wifi: rtlwifi: remove unused dualmac control leftovers
+    - wifi: rtlwifi: destroy workqueue at rtl_deinit_core
+    - wifi: rtlwifi: pci: wait for firmware loading before releasing memory
+    - HID: multitouch: Add support for lenovo Y9000P Touchpad
+    - Revert "HID: multitouch: Add support for lenovo Y9000P Touchpad"
+    - HID: multitouch: fix support for Goodix PID 0x01e9
+    - regulator: dt-bindings: mt6315: Drop regulator-compatible property
+    - ACPI: fan: cleanup resources in the error path of .probe()
+    - cpupower: fix TSC MHz calculation
+    - dt-bindings: mfd: bd71815: Fix rsense and typos
+    - leds: netxbig: Fix an OF node reference leak in netxbig_leds_get_of_pdata()
+    - cpufreq: schedutil: Fix superfluous updates caused by need_freq_update
+    - clk: imx8mp: Fix clkout1/2 support
+    - regulator: of: Implement the unwind path of of_regulator_match()
+    - samples/landlock: Fix possible NULL dereference in parse_path()
+    - wifi: wlcore: fix unbalanced pm_runtime calls
+    - net/smc: fix data error when recvmsg with MSG_PEEK flag
+    - landlock: Move filesystem helpers and add a new one
+    - wifi: mt76: mt76u_vendor_request: Do not print error messages when -EPROTO
+    - cpufreq: ACPI: Fix max-frequency computation
+    - selftests: harness: fix printing of mismatch values in __EXPECT()
+    - wifi: cfg80211: Handle specific BSSID in 6GHz scanning
+    - wifi: cfg80211: adjust allocation of colocated AP data
+    - clk: analogbits: Fix incorrect calculation of vco rate delta
+    - selftests/landlock: Fix error message
+    - net/mlxfw: Drop hard coded max FW flash image size
+    - netfilter: nft_flow_offload: update tcp state flags under lock
+    - tcp_cubic: fix incorrect HyStart round start detection
+    - tools/testing/selftests/bpf/test_tc_tunnel.sh: Fix wait for server bind
+    - libbpf: Fix segfault due to libelf functions not setting errno
+    - ASoC: sun4i-spdif: Add clock multiplier settings
+    - perf header: Fix one memory leakage in process_bpf_btf()
+    - perf header: Fix one memory leakage in process_bpf_prog_info()
+    - perf bpf: Fix two memory leakages when calling
+      perf_env__insert_bpf_prog_info()
+    - ASoC: renesas: rz-ssi: Use only the proper amount of dividers
+    - ktest.pl: Remove unused declarations in run_bisect_test function
+    - crypto: hisilicon/sec - add some comments for soft fallback
+    - crypto: hisilicon/sec - delete redundant blank lines
+    - crypto: hisilicon/sec2 - optimize the error return process
+    - crypto: hisilicon/sec2 - fix for aead icv error
+    - crypto: hisilicon/sec2 - fix for aead invalid authsize
+    - crypto: ixp4xx - fix OF node reference leaks in init_ixp_crypto()
+    - padata: fix sysfs store callback check
+    - perf top: Don't complain about lack of vmlinux when not resolving some
+      kernel samples
+    - perf report: Fix misleading help message about --demangle
+    - padata: add pd get/put refcnt helper
+    - ARM: at91: pm: change BU Power Switch to automatic mode
+    - arm64: dts: mt8183: set DMIC one-wire mode on Damu
+    - arm64: dts: mediatek: mt8516: fix GICv2 range
+    - arm64: dts: mediatek: mt8516: fix wdt irq type
+    - arm64: dts: mediatek: mt8516: remove 2 invalid i2c clocks
+    - arm64: dts: mediatek: mt8516: add i2c clock-div property
+    - arm64: dts: mediatek: mt8516: reserve 192 KiB for TF-A
+    - RDMA/mlx4: Avoid false error about access to uninitialized gids array
+    - arm64: dts: mediatek: mt8173-evb: Drop regulator-compatible property
+    - arm64: dts: mediatek: mt8173-elm: Drop regulator-compatible property
+    - arm64: dts: mediatek: mt8173-elm: Fix MT6397 PMIC sub-node names
+    - arm64: dts: mediatek: mt8173-evb: Fix MT6397 PMIC sub-node names
+    - arm64: dts: mediatek: mt8183: kenzo: Support second source touchscreen
+    - arm64: dts: mediatek: mt8183: willow: Support second source touchscreen
+    - memory: Add LPDDR2-info helpers
+    - memory: tegra20-emc: Support matching timings by LPDDR2 configuration
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Drop pp3300_panel voltage
+      settings
+    - arm64: dts: qcom: msm8996: Fix up USB3 interrupts
+    - arm64: dts: qcom: msm8994: Describe USB interrupts
+    - arm64: dts: qcom: msm8916: correct sleep clock frequency
+    - arm64: dts: qcom: msm8994: correct sleep clock frequency
+    - arm64: dts: qcom: sc7280: correct sleep clock frequency
+    - arm64: dts: qcom: sm6125: correct sleep clock frequency
+    - arm64: dts: qcom: sm8250: correct sleep clock frequency
+    - arm64: dts: qcom: sm8350: correct sleep clock frequency
+    - arm64: dts: qcom: sm8150-microsoft-surface-duo: fix typos in da7280
+      properties
+    - arm64: dts: qcom: sdm845: Fix interrupt types of camss interrupts
+    - ARM: dts: mediatek: mt7623: fix IR nodename
+    - fbdev: omapfb: Fix an OF node leak in dss_of_port_get_parent_device()
+    - RDMA/mlx5: Remove iova from struct mlx5_core_mkey
+    - RDMA/mlx5: Enforce umem boundaries for explicit ODP page faults
+    - RDMA/mlx5: Fix indirect mkey ODP page count
+    - xen/x86: free_p2m_page: use memblock_free_ptr() to free a virtual pointer
+    - memblock: drop memblock_free_early_nid() and memblock_free_early()
+    - of: reserved-memory: Do not make kmemleak ignore freed address
+    - efi: sysfb_efi: fix W=1 warnings when EFI is not set
+    - media: rc: iguanair: handle timeouts
+    - media: lmedm04: Handle errors for lme2510_int_read
+    - PCI: endpoint: Destroy the EPC device in devm_pci_epc_destroy()
+    - media: marvell: Add check for clk_enable()
+    - media: i2c: imx412: Add missing newline to prints
+    - media: i2c: ov9282: Correct the exposure offset
+    - media: mipi-csis: Add check for clk_enable()
+    - media: camif-core: Add check for clk_enable()
+    - media: uvcvideo: Propagate buf->error to userspace
+    - mtd: hyperbus: Make hyperbus_unregister_device() return void
+    - mtd: hyperbus: hbmc-am654: Convert to platform remove callback returning
+      void
+    - mtd: hyperbus: hbmc-am654: fix an OF node reference leak
+    - staging: media: imx: fix OF node leak in imx_media_add_of_subdevs()
+    - scsi: mpt3sas: Set ioc->manu_pg11.EEDPTagMode directly to 1
+    - scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
+    - ocfs2: mark dquot as inactive if failed to start trans while releasing dquot
+    - module: Extend the preempt disabled section in
+      dereference_symbol_descriptor().
+    - NFSv4.2: fix COPY_NOTIFY xdr buf size calculation
+    - NFSv4.2: mark OFFLOAD_CANCEL MOVEABLE
+    - tools/bootconfig: Fix the wrong format specifier
+    - xfrm: replay: Fix the update of replay_esn->oseq_hi for GSO
+    - dmaengine: ti: edma: fix OF node reference leaks in edma_driver
+    - gpio: mxc: remove dead code after switch to DT-only
+    - net: fec: implement TSO descriptor cleanup
+    - PM: hibernate: Add error handling for syscore_suspend()
+    - net: netdevsim: try to close UDP port harness races
+    - ptp: Properly handle compat ioctls
+    - perf trace: Fix runtime error of index out of bounds
+    - vsock: Allow retrying on connect() failure
+    - bgmac: reduce max frame size to support just MTU 1500
+    - net: sh_eth: Fix missing rtnl lock in suspend/resume path
+    - net: hsr: fix fill_frame_info() regression vs VLAN packets
+    - genksyms: fix memory leak when the same symbol is added from source
+    - genksyms: fix memory leak when the same symbol is read from *.symref file
+    - kconfig: fix file name in warnings when loading KCONFIG_DEFCONFIG_LIST
+    - kconfig: add warn-unknown-symbols sanity check
+    - kconfig: require a space after '#' for valid input
+    - kconfig: remove unused code for S_DEF_AUTO in conf_read_simple()
+    - kconfig: deduplicate code in conf_read_simple()
+    - kconfig: WERROR unmet symbol dependency
+    - kconfig: fix memory leak in sym_warn_unmet_dep()
+    - hexagon: fix using plain integer as NULL pointer warning in cmpxchg
+    - hexagon: Fix unbalanced spinlock in die()
+    - f2fs: Introduce linear search for dentries
+    - ktest.pl: Check kernelrelease return in get_version
+    - ALSA: usb-audio: Add delay quirk for iBasso DC07 Pro
+    - drivers/card_reader/rtsx_usb: Restore interrupt based detection
+    - usb: gadget: f_tcm: Fix Get/SetInterface return value
+    - usb: dwc3: core: Defer the probe until USB power supply ready
+    - usb: typec: tcpm: set SRC_SEND_CAPABILITIES timeout to PD_T_SENDER_RESPONSE
+    - usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS
+    - btrfs: output the reason for open_ctree() failure
+    - btrfs: fix data race when accessing the inode's disk_i_size at
+      btrfs_drop_extents()
+    - btrfs: convert BUG_ON in btrfs_reloc_cow_block() to proper error handling
+    - sched: Don't try to catch up excess steal time.
+    - lockdep: Fix upper limit for LOCKDEP_*_BITS configs
+    - x86/amd_nb: Restrict init function to AMD-based systems
+    - tun: fix group permission check
+    - mmc: core: Respect quirk_max_rate for non-UHS SDIO card
+    - mfd: lpc_ich: Add another Gemini Lake ISA bridge PCI device-id
+    - HID: Wacom: Add PCI Wacom device support
+    - net/mlx5: use do_aux_work for PHC overflow checks
+    - wifi: iwlwifi: avoid memory leak
+    - i2c: Force ELAN06FA touchpad I2C bus freq to 100KHz
+    - APEI: GHES: Have GHES honor the panic= setting
+    - net: wwan: iosm: Fix hibernation by re-binding the driver around it
+    - mmc: sdhci-msm: Correctly set the load for the regulator
+    - tipc: re-order conditions in tipc_crypto_key_rcv()
+    - selftests/net/ipsec: Fix Null pointer dereference in rtattr_pack()
+    - Input: allocate keycode for phone linking
+    - platform/x86: acer-wmi: Ignore AC events
+    - x86/mm: Don't disable PCID when INVLPG has been fixed by microcode
+    - usb: chipidea: ci_hdrc_imx: use dev_err_probe()
+    - usb: chipidea/ci_hdrc_imx: Convert to platform remove callback returning
+      void
+    - usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in
+      the error path of .probe()
+    - net/ncsi: Add NC-SI 1.2 Get MC MAC Address command
+    - net/ncsi: fix locking in Get MAC Address handling
+    - xfs: report realtime block quota limits on realtime directories
+    - xfs: don't over-report free space or inodes in statvfs
+    - usb: xhci: Add timeout argument in address_device USB HCD callback
+    - nvme: handle connectivity loss in nvme_set_queue_count
+    - firmware: iscsi_ibft: fix ISCSI_IBFT Kconfig entry
+    - gpu: drm_dp_cec: fix broken CEC adapter properties check
+    - tg3: Disable tg3 PCIe AER on system reboot
+    - udp: gso: do not drop small packets when PMTU reduces
+    - gpio: pca953x: Improve interrupt support
+    - net: atlantic: fix warning during hot unplug
+    - x86/xen: fix xen_hypercall_hvm() to not clobber %rbx
+    - x86/xen: add FRAME_END to xen_hypercall_hvm()
+    - tun: revert fix group permission check
+    - cpufreq: s3c64xx: Fix compilation warning
+    - leds: lp8860: Write full EEPROM, not only half of it
+    - drm/modeset: Handle tiled displays in pan_display_atomic.
+    - s390/futex: Fix FUTEX_OP_ANDN implementation
+    - m68k: vga: Fix I/O defines
+    - arm64: dts: rockchip: increase gmac rx_delay on rk3399-puma
+    - KVM: s390: vsie: fix some corner-cases when grabbing vsie pages
+    - drm/amd/pm: Mark MM activity as unsupported
+    - drm/komeda: Add check for komeda_get_layer_fourcc_list()
+    - drm/i915: Drop 64bpp YUV formats from ICL+ SDR planes
+    - Bluetooth: L2CAP: accept zero as a special value for MTU auto-selection
+    - clk: sunxi-ng: a100: enable MMC clock reparenting
+    - clk: qcom: clk-alpha-pll: fix alpha mode configuration
+    - clk: qcom: gcc-mdm9607: Fix cmd_rcgr offset for blsp1_uart6 rcg
+    - clk: qcom: clk-rpmh: prevent integer overflow in recalc_rate
+    - efi: libstub: Use '-std=gnu11' to fix build with GCC 15
+    - perf bench: Fix undefined behavior in cmpworker()
+    - of: Correct child specifier used as input of the 2nd nexus node
+    - of: Fix of_find_node_opts_by_path() handling of alias+path+options
+    - of: reserved-memory: Fix using wrong number of cells to get property
+      'alignment'
+    - HID: hid-sensor-hub: don't use stale platform-data on remove
+    - wifi: rtlwifi: rtl8821ae: Fix media status report
+    - usb: gadget: f_tcm: Translate error to sense
+    - usb: gadget: f_tcm: Decrement command ref count on cleanup
+    - usb: gadget: f_tcm: ep_autoconfig with fullspeed endpoint
+    - usb: gadget: f_tcm: Don't prepare BOT write request twice
+    - serial: sh-sci: Drop __initdata macro for port_cfg
+    - serial: sh-sci: Do not probe the serial port if its slot in sci_ports[] is
+      in use
+    - MIPS: Loongson64: remove ROM Size unit in boardinfo
+    - powerpc/pseries/eeh: Fix get PE state translation
+    - dm-crypt: don't update io->sector after kcryptd_crypt_write_io_submit()
+    - dm-crypt: track tag_offset in convert_context
+    - mips/math-emu: fix emulation of the prefx instruction
+    - ALSA: hda/realtek: Enable headset mic on Positivo C6400
+    - PCI: endpoint: Finish virtual EP removal in pci_epf_remove_vepf()
+    - nvme-pci: Add TUXEDO InfinityFlex to Samsung sleep quirk
+    - nvme-pci: Add TUXEDO IBP Gen9 to Samsung sleep quirk
+    - scsi: qla2xxx: Move FCE Trace buffer allocation to user control
+    - scsi: storvsc: Set correct data length for sending SCSI command without
+      payload
+    - kbuild: Move -Wenum-enum-conversion to W=2
+    - x86/boot: Use '-std=gnu11' to fix build with GCC 15
+    - arm64: dts: qcom: sm8350: Fix MPSS memory length
+    - crypto: qce - fix priority to be less than ARMv8 CE
+    - xfs: Add error handling for xfs_reflink_cancel_cow_range
+    - media: ccs: Clean up parsed CCS static data on parse failure
+    - iio: light: as73211: fix channel handling in only-color triggered buffer
+    - soc: qcom: smem_state: fix missing of_node_put in error path
+    - media: mc: fix endpoint iteration
+    - media: ov5640: fix get_light_freq on auto
+    - media: ccs: Fix CCS static data parsing for large block sizes
+    - media: ccs: Fix cleanup order in ccs_probe()
+    - media: uvcvideo: Fix event flags in uvc_ctrl_send_events
+    - media: uvcvideo: Remove redundant NULL assignment
+    - crypto: qce - fix goto jump in error path
+    - crypto: qce - unregister previously registered algos in error path
+    - nvmem: qcom-spmi-sdam: Set size in struct nvmem_config
+    - nvmem: core: improve range check for nvmem_cell_write()
+    - vfio/platform: check the bounds of read/write syscalls
+    - pnfs/flexfiles: retry getting layout segment for reads
+    - ocfs2: fix incorrect CPU endianness conversion causing mount failure
+    - mtd: onenand: Fix uninitialized retlen in do_otp_read()
+    - misc: fastrpc: Fix registered buffer page address
+    - net/ncsi: wait for the last response to Deselect Package before configuring
+      channel
+    - net: phy: c45-tjaxx: add delay between MDIO write and read in soft_reset
+    - MIPS: ftrace: Declare ftrace_get_parent_ra_addr() as static
+    - net/ncsi: use dev_set_mac_address() for Get MC MAC Address handling
+    - gpio: xilinx: remove excess kernel doc
+    - memory: tegra20-emc: Correct memory device mask
+    - ocfs2: check dir i_size in ocfs2_find_entry
+    - mptcp: prevent excessive coalescing on receive
+    - ndisc: ndisc_send_redirect() must use dev_get_by_index_rcu()
+    - drm/i915/selftests: avoid using uninitialized context
+    - gpio: bcm-kona: Fix GPIO lock/unlock for banks above bank 0
+    - gpio: bcm-kona: Make sure GPIO bits are unlocked when requesting IRQ
+    - gpio: bcm-kona: Add missing newline to dev_err format string
+    - xen: remove a confusing comment on auto-translated guest I/O
+    - x86/xen: allow larger contiguous memory regions in PV guests
+    - media: cxd2841er: fix 64-bit division on gcc-9
+    - PCI/DPC: Quirk PIO log size for Intel Raptor Lake-P
+    - vfio/pci: Enable iowrite64 and ioread64 for vfio pci
+    - Grab mm lock before grabbing pt lock
+    - x86/mm/tlb: Only trim the mm_cpumask once a second
+    - ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet 5V
+    - batman-adv: Ignore neighbor throughput metrics in error case
+    - perf/x86/intel: Ensure LBRs are disabled when a CPU is starting
+    - usb: roles: set switch registered flag early on
+    - usb: gadget: udc: renesas_usb3: Fix compiler warning
+    - usb: dwc2: gadget: remove of_node reference upon udc_stop
+    - USB: pci-quirks: Fix HCCPARAMS register error for LS7A EHCI
+    - usb: core: fix pipe creation for get_bMaxPacketSize0
+    - USB: quirks: add USB_QUIRK_NO_LPM quirk for Teclast dist
+    - USB: Add USB_QUIRK_NO_LPM quirk for sony xperia xz1 smartphone
+    - USB: cdc-acm: Fill in Renesas R-Car D3 USB Download mode quirk
+    - usb: cdc-acm: Fix handling of oversized fragments
+    - USB: serial: option: add MeiG Smart SLM828
+    - USB: serial: option: add Telit Cinterion FN990B compositions
+    - USB: serial: option: fix Telit Cinterion FN990A name
+    - USB: serial: option: drop MeiG Smart defines
+    - can: c_can: fix unbalanced runtime PM disable in error path
+    - can: j1939: j1939_sk_send_loop(): fix unable to send messages with data
+      length zero
+    - alpha: make stack 16-byte aligned (most cases)
+    - efi: Avoid cold plugged memory for placing the kernel
+    - cgroup: fix race between fork and cgroup.kill
+    - serial: 8250: Fix fifo underflow on flush
+    - alpha: align stack for page fault and user unaligned trap handlers
+    - gpio: stmpe: Check return value of stmpe_reg_read in
+      stmpe_gpio_irq_sync_unlock
+    - regmap-irq: Add missing kfree()
+    - arm64: Handle .ARM.attributes section in linker scripts
+    - mlxsw: Add return value check for mlxsw_sp_port_get_stats_raw()
+    - btrfs: fix hole expansion when writing at an offset beyond EOF
+    - clocksource: Replace cpumask_weight() with cpumask_empty()
+    - clocksource: Use pr_info() for "Checking clocksource synchronization"
+      message
+    - ipv4: add RCU protection to ip4_dst_hoplimit()
+    - net: treat possible_net_t net pointer as an RCU one and add read_pnet_rcu()
+    - net: add dev_net_rcu() helper
+    - ipv4: use RCU protection in rt_is_expired()
+    - ipv4: use RCU protection in inet_select_addr()
+    - Namespaceify min_pmtu sysctl
+    - Namespaceify mtu_expires sysctl
+    - selftest: net: Test IPv4 PMTU exceptions with DSCP and ECN
+    - net: ipv4: Cache pmtu for all packet paths if multipath enabled
+    - neighbour: delete redundant judgment statements
+    - drm/tidss: Fix issue in irq handling causing irq-flood issue
+    - drm/tidss: Clear the interrupt status for interrupts being disabled
+    - kdb: Do not assume write() callback available
+    - alpha: replace hardcoded stack offsets with autogenerated ones
+    - nilfs2: do not output warnings when clearing dirty buffers
+    - can: ems_pci: move ASIX AX99100 ids to pci_ids.h
+    - serial: 8250_pci: add support for ASIX AX99100
+    - parport_pc: add support for ASIX AX99100
+    - netdevsim: print human readable IP address
+    - selftests: rtnetlink: update netdevsim ipsec output format
+    - ARM: dts: dra7: Add bus_dma_limit for l4 cfg bus
+    - x86/i8253: Disable PIT timer 0 when not in use
+    - Revert "btrfs: avoid monopolizing a core when activating a swap file"
+    - btrfs: avoid monopolizing a core when activating a swap file
+    - arm64: mte: Do not allow PROT_MTE on MAP_HUGETLB user mappings
+    - crypto: testmgr - fix wrong key length for pkcs1pad
+    - crypto: testmgr - Fix wrong test case of RSA
+    - crypto: testmgr - fix version number of RSA tests
+    - crypto: testmgr - populate RSA CRT parameters in RSA test vectors
+    - crypto: testmgr - some more fixes to RSA test vectors
+    - mm: update mark_victim tracepoints fields
+    - drm/probe-helper: Create a HPD IRQ event helper for a single connector
+    - drm/rockchip: cdn-dp: Use drm_connector_helper_hpd_irq_event()
+    - ASoC: renesas: rz-ssi: Add a check for negative sample_space
+    - arm64: dts: mediatek: mt8183: Disable DSI display output by default
+    - tpm: Use managed allocation for bios event log
+    - kfence: allow use of a deferrable timer
+    - [Config] updateconfigs to disable new KFENCE_DEFERRABLE
+    - kfence: enable check kfence canary on panic via boot param
+    - kfence: skip __GFP_THISNODE allocations on NUMA systems
+    - soc: mediatek: mtk-devapc: Switch to devm_clk_get_enabled()
+    - soc: mediatek: mtk-devapc: Fix leaking IO map on error paths
+    - soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
+    - soc: mediatek: mtk-devapc: Fix leaking IO map on driver remove
+    - media: uvcvideo: Set error_idx during ctrl_commit errors
+    - media: uvcvideo: Refactor iterators
+    - media: uvcvideo: Only save async fh if success
+    - batman-adv: Drop initialization of flexible ethtool_link_ksettings
+    - usb: dwc3: Increase DWC3 controller halt timeout
+    - usb: dwc3: Fix timeout issue during controller enter/exit from halt state
+    - powerpc/64s/mm: Move __real_pte stubs into hash-4k.h
+    - powerpc/64s: Rewrite __real_pte() and __rpte_to_hidx() as static inline
+    - ALSA: hda/realtek: Fixup ALC225 depop procedure
+    - geneve: Suppress list corruption splat in geneve_destroy_tunnels().
+    - net: extract port range fields from fl_flow_key
+    - flow_dissector: Fix handling of mixed port and port-range keys
+    - flow_dissector: Fix port range key handling in BPF conversion
+    - net: Add non-RCU dev_getbyhwaddr() helper
+    - arp: switch to dev_getbyhwaddr() in arp_req_set_public()
+    - power: supply: da9150-fg: fix potential overflow
+    - nvme/ioctl: add missing space in err message
+    - bpf: skip non exist keys in generic_map_lookup_batch
+    - ALSA: hda/conexant: Add quirk for HP ProBook 450 G4 mute LED
+    - acct: block access to kernel internal filesystems
+    - mtd: rawnand: cadence: fix error code in cadence_nand_init()
+    - mtd: rawnand: cadence: use dma_map_resource for sdma address
+    - mtd: rawnand: cadence: fix incorrect device in dma_unmap_single
+    - x86/cpu/kvm: SRSO: Fix possible missing IBPB on VM-Exit
+    - IB/mlx5: Set and get correct qp_num for a DCT QP
+    - ovl: use wrappers to all vfs_*xattr() calls
+    - ovl: pass ofs to creation operations
+    - scsi: core: Don't memset() the entire scsi_cmnd in scsi_init_command()
+    - scsi: core: Clear driver private data when retrying request
+    - RDMA/mlx5: Fix bind QP error cleanup flow
+    - sunrpc: suppress warnings for unused procfs functions
+    - ALSA: usb-audio: Avoid dropping MIDI events at closing multiple ports
+    - Bluetooth: L2CAP: Fix L2CAP_ECRED_CONN_RSP response
+    - afs: remove variable nr_servers
+    - afs: Make it possible to find the volumes that are using a server
+    - afs: Fix the server_list to unuse a displaced server rather than putting it
+    - net: loopback: Avoid sending IP packets without an Ethernet header
+    - net: cadence: macb: Synchronize stats calculations
+    - ASoC: es8328: fix route from DAC to output
+    - ipvs: Always clear ipvs_property flag in skb_scrub_packet()
+    - tcp: Defer ts_recent changes until req is owned
+    - net: mvpp2: cls: Fixed Non IP flow, with vlan tag flow defination.
+    - net/mlx5: IRQ, Fix null string in debug print
+    - seg6: add support for SRv6 H.Encaps.Red behavior
+    - seg6: add support for SRv6 H.L2Encaps.Red behavior
+    - include: net: add static inline dst_dev_overhead() to dst.h
+    - net: ipv6: seg6_iptunnel: mitigate 2-realloc issue
+    - net: ipv6: fix dst ref loop on input in seg6 lwt
+    - net: ipv6: rpl_iptunnel: mitigate 2-realloc issue
+    - net: ipv6: fix dst ref loop on input in rpl lwt
+    - x86/CPU: Fix warm boot hang regression on AMD SC1100 SoC systems
+    - ftrace: Avoid potential division by zero in function_stat_show()
+    - ALSA: usb-audio: Re-add sample rate quirk for Pioneer DJM-900NXS2
+    - perf/core: Fix low freq setting via IOC_PERIOD
+    - drm/amd/display: Fix HPD after gpu reset
+    - net: enetc: fix the off-by-one issue in enetc_map_tx_buffs()
+    - net: enetc: update UDP checksum when updating originTimestamp field
+    - net: enetc: correct the xdp_tx statistics
+    - phy: tegra: xusb: reset VBUS & ID OVERRIDE
+    - phy: exynos5-usbdrd: fix MPLL_MULTIPLIER and SSC_REFCLKSEL masks in refclk
+    - vmlinux.lds: Ensure that const vars with relocations are mapped R/O
+    - intel_idle: Handle older CPUs, which stop the TSC in deeper C states,
+      correctly
+    - drm/amdgpu: Check extended configuration space register when system uses
+      large bar
+    - drm/amdgpu: disable BAR resize on Dell G5 SE
+    - Revert "of: reserved-memory: Fix using wrong number of cells to get property
+      'alignment'"
+    - HID: appleir: Fix potential NULL dereference at raw event handle
+    - gpio: rcar: Use raw_spinlock to protect register access
+    - gpio: aggregator: protect driver attr handlers against module unload
+    - ALSA: hda: intel: Add Dell ALC3271 to power_save denylist
+    - ALSA: hda/realtek: update ALC222 depop optimize
+    - drm/radeon: Fix rs400_gpu_init for ATI mobility radeon Xpress 200M
+    - platform/x86: thinkpad_acpi: Add battery quirk for ThinkPad X131e
+    - x86/cacheinfo: Validate CPUID leaf 0x2 EDX output
+    - x86/cpu: Validate CPUID leaf 0x2 EDX output
+    - x86/cpu: Properly parse CPUID leaf 0x2 TLB descriptor 0x63
+    - wifi: cfg80211: regulatory: improve invalid hints checking
+    - wifi: nl80211: reject cooked mode if it is set along with other flags
+    - rapidio: add check for rio_add_net() in rio_scan_alloc_net()
+    - rapidio: fix an API misues when rio_add_net() fails
+    - s390/traps: Fix test_monitor_call() inline assembly
+    - block: fix conversion of GPT partition name to 7-bit
+    - mm/page_alloc: fix uninitialized variable
+    - mm: don't skip arch_sync_kernel_mappings() in error paths
+    - wifi: iwlwifi: limit printed string from FW file
+    - HID: google: fix unused variable warning under !CONFIG_ACPI
+    - HID: intel-ish-hid: Fix use-after-free issue in ishtp_hid_remove()
+    - nvmet-tcp: Fix a possible sporadic response drops in weakly ordered arch
+    - net: gso: fix ownership in __udp_gso_segment
+    - caif_virtio: fix wrong pointer check in cfv_probe()
+    - hwmon: (pmbus) Initialise page count in pmbus_identify()
+    - hwmon: (ntc_thermistor) Fix the ncpXXxh103 sensor table
+    - hwmon: (ad7314) Validate leading zero bits and return error
+    - ALSA: usx2y: validate nrpacks module parameter on probe
+    - llc: do not use skb_get() before dev_queue_xmit()
+    - hwmon: fix a NULL vs IS_ERR_OR_NULL() check in xgene_hwmon_probe()
+    - drm/sched: Fix preprocessor guard
+    - be2net: fix sleeping while atomic bugs in be_ndo_bridge_getlink
+    - net: hns3: make sure ptp clock is unregister and freed if
+      hclge_ptp_get_cycle returns an error
+    - ppp: Fix KMSAN uninit-value warning with bpf
+    - vlan: enforce underlying device type
+    - x86/sgx: Support loading enclave page without VMA permissions check
+    - x86/sgx: Move PTE zap code to new sgx_zap_enclave_ptes()
+    - x86/sgx: Export sgx_encl_{grow,shrink}()
+    - x86/sgx: Support VA page allocation without reclaiming
+    - x86/sgx: Fix size overflows in sgx_encl_create()
+    - exfat: fix soft lockup in exfat_clear_bitmap
+    - net-timestamp: support TCP GSO case for a few missing flags
+    - sched/fair: Fix potential memory corruption in child_cfs_rq_on_list
+    - net: ipv6: fix dst ref loop in ila lwtunnel
+    - net: ipv6: fix missing dst ref drop in ila lwtunnel
+    - gpio: rcar: Fix missing of_node_put() call
+    - Revert "drivers/card_reader/rtsx_usb: Restore interrupt based detection"
+    - usb: renesas_usbhs: Call clk_put()
+    - usb: renesas_usbhs: Use devm_usb_get_phy()
+    - usb: hub: lack of clearing xHC resources
+    - usb: quirks: Add DELAY_INIT and NO_LPM for Prolific Mass Storage Card Reader
+    - usb: renesas_usbhs: Flush the notify_hotplug_work
+    - usb: atm: cxacru: fix a flaw in existing endpoint checks
+    - usb: dwc3: Set SUSPENDENABLE soon after phy init
+    - usb: dwc3: gadget: Prevent irq storm when TH re-executes
+    - usb: typec: ucsi: increase timeout for PPM reset operations
+    - usb: typec: tcpci_rt1711h: Unmask alert interrupts to fix functionality
+    - usb: gadget: Set self-powered based on MaxPower and bmAttributes
+    - usb: gadget: Fix setting self-powered state on suspend
+    - usb: gadget: Check bmAttributes only if configuration is valid
+    - xhci: pci: Fix indentation in the PCI device ID definitions
+    - usb: xhci: Enable the TRB overfetch quirk on VIA VL805
+    - mei: me: add panther lake P DID
+    - intel_th: pci: Add Arrow Lake support
+    - intel_th: pci: Add Panther Lake-H support
+    - intel_th: pci: Add Panther Lake-P/U support
+    - slimbus: messaging: Free transaction ID in delayed interrupt scenario
+    - bus: mhi: host: pci_generic: Use pci_try_reset_function() to avoid deadlock
+    - eeprom: digsy_mtc: Make GPIO lookup table match the device
+    - drivers: virt: acrn: hsm: Use kzalloc to avoid info leak in pmcmd_ioctl
+    - media: uvcvideo: Avoid invalid memory access
+    - media: uvcvideo: Avoid returning invalid controls
+    - md: select BLOCK_LEGACY_AUTOLOAD
+    - [Config] updateconfigs to select BLOCK_LEGACY_AUTOLOAD
+    - mtd: rawnand: cadence: fix unchecked dereference
+    - spi-mxs: Fix chipselect glitch
+    - nilfs2: move page release outside of nilfs_delete_entry and nilfs_set_link
+    - nilfs2: eliminate staggered calls to kunmap in nilfs_rename
+    - bpf, vsock: Invoke proto::close on close()
+    - kbuild: userprogs: use correct lld when linking through clang
+    - net: ipv6: fix dst refleaks in rpl, seg6 and ioam6 lwtunnels
+    - Linux 5.15.179
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21647
+    - sched: sch_cake: add bounds checks to host bulk flow fairness counts
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58002
+    - media: uvcvideo: Remove dangling pointers
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58079
+    - media: uvcvideo: Fix crash during unbind if gpio unit is in use
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21721
+    - nilfs2: handle errors that nilfs_prepare_chunk() may return
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-26982
+    - Squashfs: check the inode number is not the invalid value of zero
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21844
+    - smb: client: Add check for next_buffer in receive_encrypted_standard()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58090
+    - sched/core: Prevent rescheduling when interrupts are disabled
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21875
+    - mptcp: always handle address removal under msk socket lock
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21877
+    - usbnet: gl620a: fix endpoint checking in genelink_bind()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21878
+    - i2c: npcm: disable interrupt enable bit before devm_request_irq
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21887
+    - ovl: fix UAF in ovl_dentry_update_reval by moving dput() in ovl_link_up
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21846
+    - acct: perform last write from workqueue
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21848
+    - nfp: bpf: Add check for nfp_app_ctrl_msg_alloc()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21862
+    - drop_monitor: fix incorrect initialization order
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21871
+    - tee: optee: Fix supplicant wait loop
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21865
+    - gtp: Suppress list corruption splat in gtp_net_exit_batch_rtnl().
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21858
+    - geneve: Fix use-after-free in geneve_find_dev().
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21866
+    - powerpc/code-patching: Fix KASAN hit by not flagging text patching area as
+      VM_ALLOC
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21859
+    - USB: gadget: f_midi: f_midi_complete to call queue_work
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21823
+    - batman-adv: Drop unmanaged ELP metric worker
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58005
+    - tpm: Change to kvalloc() in eventlog/acpi.c
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21748
+    - ksmbd: fix integer overflows on 32 bit systems
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57977
+    - memcg: fix soft lockup in the OOM process
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57978
+    - media: imx-jpeg: Fix potential error pointer dereference in detach_pm()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57979
+    - pps: Fix a use-after-free
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-47726
+    - f2fs: fix to wait dio completion
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21811
+    - nilfs2: protect access to buffers with no active references
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21722
+    - nilfs2: do not force clear folio if buffer is referenced
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58086
+    - drm/v3d: Stop active perfmon if it is being destroyed
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21758
+    - ipv6: mcast: add RCU protection to mld_newpack()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21760
+    - ndisc: extend RCU protection in ndisc_send_skb()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21761
+    - openvswitch: use RCU protection in ovs_vport_cmd_fill_info()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21762
+    - arp: use RCU protection in arp_xmit()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21763
+    - neighbour: use RCU protection in __neigh_notify()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21764
+    - ndisc: use RCU protection in ndisc_alloc_skb()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21765
+    - ipv6: use RCU protection in ip6_default_advmss()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21766
+    - ipv4: use RCU protection in __ip_rt_update_pmtu()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21767
+    - clocksource: Use migrate_disable() to avoid calling get_random_u32() in
+      atomic context
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21772
+    - partitions: mac: fix handling of bogus partition table
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21704
+    - usb: cdc-acm: Check control transfer buffer size before access
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21776
+    - USB: hub: Ignore non-compliant devices with too many configs or interfaces
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21835
+    - usb: gadget: f_midi: fix MIDI Streaming descriptor lengths
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21779
+    - KVM: x86: Reject Hyper-V's SEND_IPI hypercalls if local APIC isn't in-kernel
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21781
+    - batman-adv: fix panic during interface removal
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21782
+    - orangefs: fix a oob in orangefs_debug_write
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57834
+    - media: vidtv: Fix a null-ptr-deref in vidtv_mux_stop_thread
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21785
+    - arm64: cacheinfo: Avoid out-of-bounds write to cacheinfo array
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21787
+    - team: better TEAM_OPTION_TYPE_STRING validation
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21791
+    - vrf: use RCU protection in l3mdev_l3_out()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58020
+    - HID: multitouch: Add NULL check in mt_input_configured
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21795
+    - NFSD: fix hang in nfsd4_shutdown_callback
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21796
+    - nfsd: clear acl_access/acl_default after releasing them
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21820
+    - tty: xilinx_uartps: split sysrq handling
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21814
+    - ptp: Ensure info->enable callback is always set
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21735
+    - NFC: nci: Add bounds checking in nci_hci_create_pipe()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21736
+    - nilfs2: fix possible int overflows in nilfs_fiemap()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58001
+    - ocfs2: handle a symlink read error correctly
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58007
+    - soc: qcom: socinfo: Avoid out of bounds read of serial number
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21744
+    - wifi: brcmfmac: fix NULL pointer dereference in brcmf_txfinalize()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21745
+    - blk-cgroup: Fix class @block_class's subsystem refcount leakage
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58076
+    - clk: qcom: gcc-sm6350: Add missing parent_map for two clocks
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58083
+    - KVM: Explicitly verify target vCPU is online in kvm_get_vcpu()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58010
+    - binfmt_flat: Fix integer overflow bug on 32 bit systems
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21749
+    - net: rose: lock the socket in rose_bind()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57981
+    - usb: xhci: Fix NULL pointer dereference on certain command aborts
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21684
+    - gpio: xilinx: Convert gpio_lock to raw spinlock
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58085
+    - tomoyo: don't emit warning in tomoyo_write_control()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58014
+    - wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58016
+    - safesetid: check size of policy writes
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58017
+    - printk: Fix signed integer overflow when defining LOG_BUF_LEN_MAX
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21753
+    - btrfs: fix use-after-free when attempting to join an aborted transaction
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58055
+    - usb: gadget: f_tcm: Don't free command immediately
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57980
+    - media: uvcvideo: Fix double free in error path
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21707
+    - mptcp: consolidate suboption status
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21708
+    - net: usb: rtl8150: enable basic endpoint checking
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21826
+    - netfilter: nf_tables: reject mismatching sum of field_len with set key
+      length
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21715
+    - net: davicom: fix UAF in dm9000_drv_remove
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21718
+    - net: rose: fix timer races against user threads
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21719
+    - ipmr: do not call mr_mfc_uses_dev() for unres entries
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21802
+    - net: hns3: fix oops when unload drivers paralleling
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58058
+    - ubifs: skip dumping tnc tree when zroot is null
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58069
+    - rtc: pcf85063: fix potential OOB write in PCF85063 NVMEM read
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21804
+    - PCI: rcar-ep: Fix incorrect variable used when calling
+      devm_request_mem_region()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58034
+    - memory: tegra20-emc: fix an OF node reference bug in
+      tegra_emc_find_node_by_ram_code()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57973
+    - rdma/cxgb4: Prevent potential integer overflow on 32bit
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21726
+    - padata: avoid UAF for reorder_work
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21727
+    - padata: fix UAF in padata_reorder
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21728
+    - bpf: Send signals asynchronously if !preemptible
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21711
+    - net/rose: prevent integer overflows in rose_setsockopt()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21799
+    - net: ethernet: ti: am65-cpsw: fix freeing IRQ in
+      am65_cpsw_nuss_remove_tx_chns()
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21806
+    - net: let net.core.dev_weight always be non-zero
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21830
+    - landlock: Handle weird files
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58071
+    - team: prevent adding a device which is already a team device lower
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58063
+    - wifi: rtlwifi: fix memory leaks and invalid access at probe error path
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58072
+    - wifi: rtlwifi: remove unused check_buddy_priv
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58051
+    - ipmi: ipmb: Add check devm_kasprintf() returned value
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58052
+    - drm/amdgpu: Fix potential NULL pointer dereference in
+      atomctrl_get_smc_sclk_range_table
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57986
+    - HID: core: Fix assumption that Resolution Multipliers must be in Logical
+      Collections
+
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21731
+    - nbd: don't allow reconnect after disconnect
+
+  * Fix bugs preventing boot on Intel TDX-enabled hosts (LP: #2097811)
+    - x86/mtrr: Remove physical address size calculation
+
+  * Build failure when CONFIG_NET_SWITCHDEV=n due to CVE-2024-26837 fix backport
+    (LP: #2104380)
+    - SAUCE: net: switchdev: fix compilation error for CONFIG_NET_SWITCHDEV=n
+
+  * nfsd hangs and never recovers after NFS4ERR_DELAY and a connection loss
+    (LP: #2103564)
+    - NFSD: Reset cb_seq_status after NFS4ERR_DELAY
+
+  * kernel hard lockup in cgroups during eBPF workload (LP: #2089318)
+    - cgroup: cgroup: Honor caller's cgroup NS when resolving cgroup id
+    - cgroup: Homogenize cgroup_get_from_id() return value
+    - cgroup: Make cgroup_get_from_id() prettier
+    - cgroup.c: add helper __cset_cgroup_from_root to cleanup duplicated codes
+    - cgroup: Reorganize css_set_lock and kernfs path processing
+
+  * CVE-2023-52664
+    - net: atlantic: eliminate double free in error handling logic
+
+  * CVE-2023-52927
+    - netfilter: allow exp not to be removed in nf_ct_find_expectation
+
+ -- Mehmet Basaran <mehmet.basaran@canonical.com>  Sat, 12 Apr 2025 08:33:00 +0300
+
+linux (5.15.0-138.148) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-138.148 -proposed tracker (LP: #2102587)
+
+  * ipsec_offload in rtnetlink.sh from ubunsu_kselftests_net fails on O/J
+    (LP: #2096976)
+    - SAUCE: selftest: netfilter: fix null IP field in kci_test_ipsec_offload
+
+  * CVE-2025-21756
+    - vsock: Keep the binding until socket destruction
+    - vsock: Orphan socket after transport release
+
+  * CVE-2024-50256
+    - netfilter: nf_reject_ipv6: fix potential crash in nf_send_reset6()
+
+  * CVE-2025-21702
+    - pfifo_tail_enqueue: Drop new packet when sch->limit == 0
+
+  * CVE-2025-21703
+    - netem: Update sch->q.qlen before qdisc_tree_reduce_backlog()
+
+  * CVE-2025-21700
+    - net: sched: Disallow replacing of child qdisc from one parent to another
+
+  * CVE-2024-46826
+    - ELF: fix kernel.randomize_va_space double read
+
+  * CVE-2024-56651
+    - can: hi311x: hi3110_can_ist(): fix potential use-after-free
+
+  * iBFT iSCSI out-of-bounds shift UBSAN warning (LP: #2097824)
+    - iscsi_ibft: Fix UBSAN shift-out-of-bounds warning in ibft_attr_show_nic()
+
+  * CVE-2024-50248
+    - ntfs3: Add bounds checking to mi_enum_attr()
+    - fs/ntfs3: Sequential field availability check in mi_enum_attr()
+
+  * CVE-2022-0995
+    - watch_queue: Use the bitmap API when applicable
+
+  * CVE-2024-26837
+    - net: bridge: switchdev: Skip MDB replays of deferred events on offload
+
+  * CVE-2025-21701
+    - net: avoid race between device unregistration and ethnl ops
+
+  * CVE-2024-57798
+    - drm/dp_mst: Skip CSN if topology probing is not done yet
+    - drm/dp_mst: Ensure mst_primary pointer is valid in
+      drm_dp_mst_handle_up_req()
+
+  * CVE-2024-56658
+    - net: defer final 'struct net' free in netns dismantle
+
+  * CVE-2024-35864
+    - smb: client: fix potential UAF in smb2_is_valid_lease_break()
+
+  * CVE-2024-35864/CVE-2024-26928
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 14 Mar 2025 15:32:05 +0100
+
+linux (5.15.0-135.146) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-135.146 -proposed tracker (LP: #2098300)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.02.10)
+
+  * Jammy update: v5.15.178 upstream stable release (LP: #2098441)
+    - ASoC: wm8994: Add depends on MFD core
+    - ASoC: samsung: Add missing selects for MFD_WM8994
+    - seccomp: Stub for !CONFIG_SECCOMP
+    - scsi: iscsi: Fix redundant response for ISCSI_UEVENT_GET_HOST_STATS request
+    - irqchip/sunxi-nmi: Add missing SKIP_WAKE flag
+    - ASoC: samsung: Add missing depends on I2C
+    - regmap: detach regmap from dev on regmap_exit
+    - mptcp: don't always assume copied data in mptcp_cleanup_rbuf()
+    - gfs2: Truncate address space when flipping GFS2_DIF_JDATA flag
+    - net: sched: fix ets qdisc OOB Indexing
+    - vfio/platform: check the bounds of read/write syscalls
+    - fs/ntfs3: Additional check in ntfs_file_release
+    - platform/chrome: cros_ec_typec: Check for EC driver
+    - ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_find()
+    - scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
+    - wifi: iwlwifi: add a few rate index validity checks
+    - USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
+    - ALSA: usb-audio: Add delay quirk for USB Audio Device
+    - Input: atkbd - map F23 key to support default copilot shortcut
+    - Input: xpad - add unofficial Xbox 360 wireless receiver clone
+    - Input: xpad - add support for wooting two he (arm)
+    - drm/v3d: Assign job pointer to NULL before signaling the fence
+    - Linux 5.15.178
+
+  * CVE-2024-49925
+    - fbdev: efifb: Register sysfs groups through driver core
+
+  * Jammy update: v5.15.177 upstream stable release (LP: #2097298)
+    - ceph: give up on paths longer than PATH_MAX
+    - jbd2: flush filesystem device before updating tail sequence
+    - dm array: fix releasing a faulty array block twice in dm_array_cursor_end
+    - dm array: fix unreleased btree blocks on closing a faulty array cursor
+    - dm array: fix cursor index when skipping across block boundaries
+    - exfat: fix the infinite loop in exfat_readdir()
+    - exfat: fix the infinite loop in __exfat_free_cluster()
+    - ASoC: mediatek: disable buffer pre-allocation
+    - ieee802154: ca8210: Add missing check for kfifo_alloc() in ca8210_probe()
+    - net: 802: LLC+SNAP OID:PID lookup on start of skb data
+    - tcp/dccp: complete lockless accesses to sk->sk_max_ack_backlog
+    - tcp/dccp: allow a connection when sk_max_ack_backlog is zero
+    - net_sched: cls_flow: validate TCA_FLOW_RSHIFT attribute
+    - bnxt_en: Fix possible memory leak when hwrm_req_replace fails
+    - cxgb4: Avoid removal of uninserted tid
+    - tls: Fix tls_sw_sendmsg error handling
+    - netfilter: nf_tables: imbalance in flowtable binding
+    - netfilter: conntrack: clamp maximum hashtable size to INT_MAX
+    - drm/mediatek: Add support for 180-degree rotation in the display driver
+    - ksmbd: fix a missing return value check bug
+    - afs: Fix the maximum cell name length
+    - dm thin: make get_first_thin use rcu-safe list first function
+    - dm-ebs: don't set the flag DM_TARGET_PASSES_INTEGRITY
+    - sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy
+    - sctp: sysctl: rto_min/max: avoid using current->nsproxy
+    - sctp: sysctl: auth_enable: avoid using current->nsproxy
+    - sctp: sysctl: udp_port: avoid using current->nsproxy
+    - sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy
+    - drm/amd/display: Add check for granularity in dml ceil/floor helpers
+    - riscv: Fix sleeping in invalid context in die()
+    - ACPI: resource: Add TongFang GM5HG0A to irq1_edge_low_force_override[]
+    - ACPI: resource: Add Asus Vivobook X1504VAP to irq1_level_low_skip_override[]
+    - drm/amd/display: increase MAX_SURFACES to the value supported by hw
+    - scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
+    - USB: serial: option: add MeiG Smart SRM815
+    - USB: serial: option: add Neoway N723-EA support
+    - staging: iio: ad9834: Correct phase range check
+    - staging: iio: ad9832: Correct phase range check
+    - usb-storage: Add max sectors quirk for Nokia 208
+    - USB: serial: cp210x: add Phoenix Contact UPS Device
+    - usb: dwc3: gadget: fix writing NYET threshold
+    - topology: Keep the cpumask unchanged when printing cpumap
+    - USB: usblp: return error when setting unsupported protocol
+    - USB: core: Disable LPM only for non-suspended ports
+    - usb: fix reference leak in usb_new_device()
+    - usb: gadget: f_uac2: Fix incorrect setting of bNumEndpoints
+    - usb: gadget: f_fs: Remove WARN_ON in functionfs_bind
+    - iio: pressure: zpa2326: fix information leak in triggered buffer
+    - iio: dummy: iio_simply_dummy_buffer: fix information leak in triggered
+      buffer
+    - iio: light: vcnl4035: fix information leak in triggered buffer
+    - iio: imu: kmx61: fix information leak in triggered buffer
+    - iio: adc: ti-ads8688: fix information leak in triggered buffer
+    - iio: gyro: fxas21002c: Fix missing data update in trigger handler
+    - iio: adc: ti-ads124s08: Use gpiod_set_value_cansleep()
+    - iio: adc: at91: call input_free_device() on allocated iio_dev
+    - iio: inkern: call iio_device_put() only on mapped devices
+    - iio: adc: ad7124: Disable all channels at probe time
+    - block, bfq: fix waker_bfqq UAF after bfq_split_bfqq()
+    - arm64: dts: rockchip: add hevc power domain clock to rk3328
+    - of: unittest: Add bus address range parsing tests
+    - of/address: Add support for 3 address cell bus
+    - of: address: Fix address translation when address-size is greater than 2
+    - of: address: Remove duplicated functions
+    - of: address: Store number of bus flag cells rather than bool
+    - of: address: Preserve the flags portion on 1:1 dma-ranges mapping
+    - phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers
+    - phy: usb: Toggle the PHY power during init
+    - ocfs2: correct return value of ocfs2_local_free_info()
+    - ocfs2: fix slab-use-after-free due to dangling pointer dqi_priv
+    - mptcp: drop port parameter of mptcp_pm_add_addr_signal
+    - mptcp: fix TCP options overflow.
+    - phy: usb: Use slow clock for wake enabled suspend
+    - phy: usb: Fix clock imbalance for suspend/resume
+    - net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()
+    - bpf: Fix bpf_sk_select_reuseport() memory leak
+    - pktgen: Avoid out-of-bounds access in get_imix_entries
+    - net: add exit_batch_rtnl() method
+    - gtp: use exit_batch_rtnl() method
+    - gtp: Use for_each_netdev_rcu() in gtp_genl_dump_pdp().
+    - gtp: Destroy device along with udp socket's netns dismantle.
+    - nfp: bpf: prevent integer overflow in nfp_bpf_event_output()
+    - net: xilinx: axienet: Fix IRQ coalescing packet count overflow
+    - net/mlx5: Add priorities for counters in RDMA namespaces
+    - net/mlx5: Refactor mlx5_get_flow_namespace
+    - net/mlx5: Fix RDMA TX steering prio
+    - drm/v3d: Ensure job pointer is set to NULL after job completion
+    - Revert "mtd: spi-nor: core: replace dummy buswidth from addr to data"
+    - i2c: mux: demux-pinctrl: check initial mux selection, too
+    - i2c: rcar: fix NACK handling when being a target
+    - mac802154: check local interfaces before deleting sdata list
+    - hfs: Sanity check the root record
+    - fs: fix missing declaration of init_files
+    - kheaders: Ignore silly-rename files
+    - ACPI: resource: acpi_dev_irq_override(): Check DMI match last
+    - poll_wait: add mb() to fix theoretical race between waitqueue_active() and
+      .poll()
+    - nvmet: propagate npwg topology
+    - net: ethernet: xgbe: re-add aneg to supported features in PHY quirks
+    - vsock/virtio: cancel close work in the destructor
+    - vsock: reset socket state when de-assigning the transport
+    - vsock: prevent null-ptr-deref in vsock_*[has_data|has_space]
+    - filemap: avoid truncating 64-bit offset to 32 bits
+    - fs/proc: fix softlockup in __read_vmcore (part 2)
+    - gpiolib: cdev: Fix use after free in lineinfo_changed_notify
+    - irqchip/gic-v3: Handle CPU_PM_ENTER_FAILED correctly
+    - hrtimers: Handle CPU state correctly on hotplug
+    - drm/i915/fb: Relax clear color alignment to 64 bytes
+    - iio: imu: inv_icm42600: fix spi burst write not supported
+    - iio: imu: inv_icm42600: fix timestamps after suspend if sensor is on
+    - iio: adc: rockchip_saradc: fix information leak in triggered buffer
+    - Revert "drm/amdgpu: rework resume handling for display (v2)"
+    - Revert "regmap: detach regmap from dev on regmap_exit"
+    - vsock/virtio: discard packets if the transport changes
+    - ipv6: avoid possible NULL deref in rt6_uncached_list_flush_dev()
+    - nfsd: add list_head nf_gc to struct nfsd_file
+    - x86/xen: fix SLS mitigation in xen_hypercall_iret()
+    - scsi: sg: Fix slab-use-after-free read in sg_release()
+    - net: fix data-races around sk->sk_forward_alloc
+    - xhci: use pm_ptr() instead of #ifdef for CONFIG_PM conditionals
+    - Partial revert of xhci: use pm_ptr() instead #ifdef for CONFIG_PM
+      conditionals
+    - Linux 5.15.177
+
+  * CVE-2024-46784
+    - net: mana: Fix error handling in mana_create_txq/rxq's NAPI cleanup
+
+  * CVE-2024-44938
+    - jfs: Fix shift-out-of-bounds in dbDiscardAG
+
+  * CVE-2024-43900
+    - media: xc2028: avoid use-after-free in load_firmware_cb()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327)
+    - ALSA: usb: Fix UBSAN warning in parse_audio_unit()
+    - usb: cdns3: Add quirk flag to enable suspend residency
+    - ASoC: Intel: sof_sdw: fix jack detection on ADL-N variant RVP
+    - PCI: vmd: Create domain symlink before pci_bus_add_devices()
+    - PCI: Add ACS quirk for Broadcom BCM5760X NIC
+    - MIPS: Loongson64: DTS: Fix msi node for ls7a
+    - usb: dwc2: gadget: Don't write invalid mapped sg entries into dma_desc with
+      iommu enabled
+    - i2c: pnx: Fix timeout in wait functions
+    - erofs: fix incorrect symlink detection in fast symlink
+    - net/smc: check sndbuf_space again after NOSPACE flag is set in smc_poll
+    - ionic: use ee->offset when returning sprom data
+    - net: hinic: Fix cleanup in create_rxqs/txqs()
+    - net: ethernet: bgmac-platform: fix an OF node reference leak
+    - netfilter: ipset: Fix for recursive locking warning
+    - net: mdiobus: fix an OF node reference leak
+    - mmc: sdhci-tegra: Remove SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC quirk
+    - chelsio/chtls: prevent potential integer overflow on 32bit
+    - i2c: riic: Always round-up when calculating bus period
+    - efivarfs: Fix error on non-existent file
+    - USB: serial: option: add TCL IK512 MBIM & ECM
+    - USB: serial: option: add MeiG Smart SLM770A
+    - USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
+    - USB: serial: option: add MediaTek T7XX compositions
+    - USB: serial: option: add Telit FE910C04 rmnet compositions
+    - hwmon: (tmp513) Don't use "proxy" headers
+    - hwmon: (tmp513) Simplify with dev_err_probe()
+    - hwmon: (tmp513) Use SI constants from units.h
+    - hwmon: (tmp513) Fix interpretation of values of Shunt Voltage and Limit
+      Registers
+    - hwmon: (tmp513) Fix Current Register value interpretation
+    - hwmon: (tmp513) Fix interpretation of values of Temperature Result and Limit
+      Registers
+    - hwmon: (tmp513) Fix division of negative numbers
+    - sh: clk: Fix clk_enable() to return 0 on NULL clk
+    - zram: refuse to use zero sized block device as backing device
+    - btrfs: tree-checker: reject inline extent items with 0 ref count
+    - tracing: Fix test_event_printk() to process entire print argument
+    - tracing: Add missing helper functions in event pointer dereference check
+    - tracing: Add "%s" check in test_event_printk()
+    - NFS/pnfs: Fix a live lock between recalled layouts and layoutget
+    - of/irq: Fix using uninitialized variable @addr_len in API of_irq_parse_one()
+    - udmabuf: also check for F_SEAL_FUTURE_WRITE
+    - of: Fix error path in of_parse_phandle_with_args_map()
+    - of: Fix refcount leakage for OF node returned by __of_get_dma_parent()
+    - ceph: validate snapdirname option length when mounting
+    - epoll: Add synchronous wakeup support for ep_poll_callback
+    - drm/amdgpu: Handle NULL bo->tbo.resource (again) in amdgpu_vm_bo_update
+    - mm/vmstat: fix a W=1 clang compiler warning
+    - tcp_bpf: Charge receive socket buffer in bpf_tcp_ingress()
+    - tcp_bpf: Add sk_rmem_alloc related logic for tcp_bpf ingress redirection
+    - bpf: Check negative offsets in __bpf_skb_min_len()
+    - nfsd: restore callback functionality for NFSv4.0
+    - mtd: diskonchip: Cast an operand to prevent potential overflow
+    - mtd: rawnand: arasan: Fix double assertion of chip-select
+    - mtd: rawnand: arasan: Fix missing de-registration of NAND
+    - phy: core: Fix an OF node refcount leakage in _of_phy_get()
+    - phy: core: Fix an OF node refcount leakage in of_phy_provider_lookup()
+    - phy: core: Fix that API devm_phy_put() fails to release the phy
+    - phy: core: Fix that API devm_of_phy_provider_unregister() fails to
+      unregister the phy provider
+    - phy: core: Fix that API devm_phy_destroy() fails to destroy the phy
+    - dmaengine: mv_xor: fix child node refcount handling in early exit
+    - dmaengine: dw: Select only supported masters for ACPI devices
+    - mtd: rawnand: fix double free in atmel_pmecc_create_user()
+    - tracing/kprobe: Make trace_kprobe's module callback called after jump_label
+      update
+    - watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04
+    - scsi: qla1280: Fix hw revision numbering for ISP1020/1040
+    - ALSA: hda/conexant: fix Z60MR100 startup pop issue
+    - regmap: Use correct format specifier for logging range errors
+    - platform/x86: asus-nb-wmi: Ignore unknown event 0xCF
+    - scsi: mpt3sas: Diag-Reset when Doorbell-In-Use bit is set during driver load
+      time
+    - scsi: storvsc: Do not flag MAINTENANCE_IN return of SRB_STATUS_DATA_OVERRUN
+      as an error
+    - virtio-blk: don't keep queue frozen during system suspend
+    - vmalloc: fix accounting with i915
+    - MIPS: Probe toolchain support of -msym32
+    - arm64: mm: Rename asid2idx() to ctxid2asid()
+    - arm64: Ensure bits ASID[15:8] are masked out when the kernel uses 8-bit
+      ASIDs
+    - drm/dp_mst: Verify request type in the corresponding down message reply
+    - lib: stackinit: hide never-taken branch from compiler
+    - ksmbd: fix racy issue from session lookup and expire
+    - tracing: Constify string literal data member in struct trace_event_call
+    - btrfs: avoid monopolizing a core when activating a swap file
+    - x86/hyperv: Fix hv tsc page based sched_clock for hibernation
+    - selinux: ignore unknown extended permissions
+    - tracing: Have process_string() also allow arrays
+    - thunderbolt: Add support for Intel Raptor Lake
+    - thunderbolt: Add support for Intel Meteor Lake
+    - thunderbolt: Add Intel Barlow Ridge PCI ID
+    - thunderbolt: Add support for Intel Lunar Lake
+    - thunderbolt: Add support for Intel Panther Lake-M/P
+    - xhci: retry Stop Endpoint on buggy NEC controllers
+    - usb: xhci: Limit Stop Endpoint retries
+    - xhci: Turn NEC specific quirk for handling Stop Endpoint errors generic
+    - RDMA/mlx5: Enforce same type port association for multiport RoCE
+    - RDMA/bnxt_re: Add check for path mtu in modify_qp
+    - RDMA/bnxt_re: Fix reporting hw_ver in query_device
+    - RDMA/bnxt_re: Fix max_qp_wrs reported
+    - RDMA/bnxt_re: Fix the locking while accessing the QP table
+    - drm/bridge: adv7511_audio: Update Audio InfoFrame properly
+    - RDMA/hns: Remove redundant 'attr_mask' in modify_qp_init_to_init()
+    - RDMA/hns: Remove redundant 'bt_level' for hem_list_alloc_item()
+    - RDMA/hns: Fix mapping error of zero-hop WQE buffer
+    - RDMA/hns: Fix warning storm caused by invalid input in IO path
+    - RDMA/hns: Fix missing flush CQE for DWQE
+    - net: stmmac: platform: provide devm_stmmac_probe_config_dt()
+    - net: stmmac: don't create a MDIO bus if unnecessary
+    - net: stmmac: restructure the error path of stmmac_probe_config_dt()
+    - drm/i915/dg1: Fix power gate sequence.
+    - net: llc: reset skb->transport_header
+    - ALSA: usb-audio: US16x08: Initialize array before use
+    - eth: bcmsysport: fix call balance of priv->clk handling routines
+    - net: mv643xx_eth: fix an OF node reference leak
+    - net: wwan: iosm: Properly check for valid exec stage in ipc_mmio_init()
+    - btrfs: rename and export __btrfs_cow_block()
+    - btrfs: sysfs: convert scnprintf and snprintf to sysfs_emit
+    - btrfs: sysfs: fix direct super block member reads
+    - wifi: mac80211: wake the queues in case of failure in resume
+    - sound: usb: enable DSD output for ddHiFi TC44C
+    - sound: usb: format: don't warn that raw DSD is unsupported
+    - bpf: fix potential error return
+    - net: usb: qmi_wwan: add Telit FE910C04 compositions
+    - irqchip/gic: Correct declaration of *percpu_base pointer in union gic_base
+    - ARC: build: Try to guess GCC variant of cross compiler
+    - usb: xhci: Avoid queuing redundant Stop Endpoint commands
+    - modpost: fix input MODULE_DEVICE_TABLE() built for 64-bit on 32-bit host
+    - modpost: fix the missed iteration for the max bit in do_input()
+    - kcov: mark in_softirq_really() as __always_inline
+    - sky2: Add device ID 11ab:4373 for Marvell 88E8075
+    - net/sctp: Prevent autoclose integer overflow in sctp_association_init()
+    - drm: adv7511: Drop dsi single lane support
+    - dt-bindings: display: adi,adv7533: Drop single lane support
+    - Linux 5.15.176
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57884
+    - mm: vmscan: account for free pages to prevent infinite Loop in
+      throttle_direct_reclaim()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57889
+    - pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57890
+    - RDMA/uverbs: Prevent integer overflow issue
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57896
+    - btrfs: flush delalloc workers queue before stopping cleaner kthread during
+      unmount
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57897
+    - drm/amdkfd: Correct the migration DMA map direction
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56759
+    - btrfs: fix use-after-free when COWing tree bock and tracing is enabled
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57900
+    - ila: serialize calls to nf_register_net_hooks()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57901
+    - af_packet: fix vlan_get_protocol_dgram() vs MSG_PEEK
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57902
+    - af_packet: fix vlan_get_tci() vs MSG_PEEK
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57903
+    - net: restrict SO_REUSEPORT to inet sockets
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-36476
+    - RDMA/rtrs: Ensure 'ib_sge list' is accessible
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57802
+    - netrom: check buffer length before accessing it
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57841
+    - net: fix memory leak in tcp_conn_request()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-49998
+    - net: dsa: improve shutdown sequence
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-50121
+    - nfsd: cancel nfsd_shrinker_work using sync mode in nfs4_state_shutdown_net
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57792
+    - power: supply: gpio-charger: Fix set charge current limits
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56763
+    - tracing: Prevent bad count for tracing_cpumask_write
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56626
+    - ksmbd: fix Out-of-Bounds Write in ksmbd_vfs_stream_write
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56627
+    - ksmbd: fix Out-of-Bounds Read in ksmbd_vfs_stream_read
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56616
+    - drm/dp_mst: Fix MST sideband message body length check
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-53099
+    - bpf: Check validity of link->type in bpf_link_show_fdinfo()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57807
+    - scsi: megaraid_sas: Fix for a potential deadlock
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56767
+    - dmaengine: at_xdmac: avoid null_prt_deref in at_xdmac_prep_dma_memset
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56769
+    - media: dvb-frontends: dib3000mb: fix uninit-value in dib3000_write_reg
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-53690
+    - nilfs2: prevent use of deleted inode
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-55881
+    - KVM: x86: Play nice with protected guests in complete_hypercall_exit()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-55916
+    - Drivers: hv: util: Avoid accessing a ringbuffer not initialized yet
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56369
+    - drm/modes: Avoid divide by zero harder in drm_mode_vrefresh()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56715
+    - ionic: Fix netdev notifier unregister on failure
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56716
+    - netdevsim: prevent bad user input in nsim_dev_health_break_write()
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57791
+    - net/smc: check return value of sock_recvmsg when draining clc data
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-47408
+    - net/smc: check smcd_v2_ext_offset when receiving proposal msg
+
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-49571
+    - net/smc: check iparea_offset and ipv6_prefixes_cnt when receiving proposal
+      msg
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302)
+    - tcp: check space before adding MPTCP SYN options
+    - ALSA: usb-audio: Add implicit feedback quirk for Yamaha THR5
+    - usb: host: max3421-hcd: Correctly abort a USB request.
+    - ata: sata_highbank: fix OF node reference leak in highbank_initialize_phys()
+    - usb: dwc2: Fix HCD resume
+    - usb: dwc2: hcd: Fix GetPortStatus & SetPortFeature
+    - usb: dwc2: Fix HCD port connection race
+    - usb: ehci-hcd: fix call balance of clocks handling routines
+    - drm/i915: Fix memory leak by correcting cache object name in error handler
+    - xfs: update btree keys correctly when _insrec splits an inode root block
+    - xfs: don't drop errno values when we fail to ficlone the entire range
+    - xfs: return from xfs_symlink_verify early on V4 filesystems
+    - xfs: fix scrub tracepoints when inode-rooted btrees are involved
+    - bpf, sockmap: Fix update element with same
+    - batman-adv: Do not send uninitialized TT changes
+    - batman-adv: Remove uninitialized data in full table TT response
+    - batman-adv: Do not let TT changes list grows indefinitely
+    - tipc: fix NULL deref in cleanup_bearer()
+    - selftests: mlxsw: sharedbuffer: Remove h1 ingress test case
+    - selftests: mlxsw: sharedbuffer: Remove duplicate test cases
+    - ptp: kvm: Use decrypted memory in confidential guest on x86
+    - ptp: kvm: x86: Return EOPNOTSUPP instead of ENODEV from kvm_arch_ptp_init()
+    - net: sparx5: fix FDMA performance issue
+    - net: sparx5: fix the maximum frame length register
+    - ACPI: resource: Fix memory resource type union access
+    - cxgb4: use port number to set mac addr
+    - qca_spi: Fix clock speed for multiple QCA7000
+    - qca_spi: Make driver probing reliable
+    - Documentation: PM: Clarify pm_runtime_resume_and_get() return value
+    - bonding: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL
+    - team: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL
+    - ACPICA: events/evxfregn: don't release the ContextMutex that was never
+      acquired
+    - blk-iocost: Avoid using clamp() on inuse in __propagate_weights()
+    - tracing/kprobes: Skip symbol counting logic for module symbols in
+      create_local_trace_kprobe()
+    - xen/netfront: fix crash when removing device
+    - x86: make get_cpu_vendor() accessible from Xen code
+    - objtool/x86: allow syscall instruction
+    - x86/static-call: provide a way to do very early static-call updates
+    - x86/static-call: Remove early_boot_irqs_disabled check to fix Xen PVH dom0
+    - x86/asm: Make serialize() always_inline
+    - x86/xen: don't do PV iret hypercall through hypercall page
+    - x86/xen: add central hypercall functions
+    - x86/xen: use new hypercall functions instead of hypercall page
+    - x86/xen: remove hypercall page
+    - ALSA: usb-audio: Fix a DMA to stack memory bug
+    - x86/static-call: fix 32-bit build
+    - Linux 5.15.175
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-53125
+    - bpf: sync_linked_regs() must preserve subreg_def
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56770
+    - net/sched: netem: account for backlog updates from child qdisc
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56659
+    - net: lapb: increase LAPB_HEADER_LEN
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56662
+    - acpi: nfit: vmalloc-out-of-bounds Read in acpi_nfit_ctl
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-42315
+    - exfat: fix potential deadlock on __exfat_get_dentry_set
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-53119
+    - virtio/vsock: Fix accept_queue memory leak
+
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56670
+    - usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to
+      accessing null pointer
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283)
+    - arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
+    - media: venus: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - media: gspca: ov534-ov772x: Fix off-by-one error in set_frame_rate()
+    - media: uvcvideo: Stop stream during unregister
+    - vmstat: call fold_vm_zone_numa_events() before show per zone NUMA event
+    - iommu/io-pgtable-arm: Fix stage-2 map/unmap for concatenated tables
+    - leds: lp55xx: Remove redundant test for invalid channel number
+    - clk: qcom: gcc-qcs404: fix initial rate of GPLL3
+    - samples: pktgen: correct dev to DEV
+    - ARM: 9419/1: mm: Fix kernel memory mapping for xip kernels
+    - x86/mm: Fix a kdump kernel failure on SME system when CONFIG_IMA_KEXEC=y
+    - vdpa/mlx5: Fix PA offset with unaligned starting iotlb map
+    - KVM: nVMX: Treat vpid01 as current if L2 is active, but with VPID disabled
+    - ocfs2: fix UBSAN warning in ocfs2_verify_volume()
+    - drm/bridge: tc358768: Fix DSI command tx
+    - mmc: sunxi-mmc: Add D1 MMC variant
+    - mmc: sunxi-mmc: Fix A100 compatible description
+    - lib/buildid: Fix build ID parsing logic
+    - media: dvbdev: fix the logic when DVB_DYNAMIC_MINORS is not set
+    - NFSD: initialize copy->cp_clp early in nfsd4_copy for use by trace point
+    - NFSD: Async COPY result needs to return a write verifier
+    - NFSD: Initialize struct nfsd4_copy earlier
+    - NFSD: Never decrement pending_async_copies on error
+    - mm: revert "mm: shmem: fix data-race in shmem_getattr()"
+    - mm: avoid unsafe VMA hook invocation when error arises on mmap hook
+    - mm: unconditionally close VMAs on error
+    - mm: refactor arch_calc_vm_flag_bits() and arm64 MTE handling
+    - NFS: nfs_async_write_reschedule_io must not recurse into the writeback code
+    - ASoC: Intel: bytcr_rt5640: Add support for non ACPI instantiated codec
+    - ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet
+    - ASoC: Intel: sst: Support LPE0F28 ACPI HID
+    - wifi: iwlwifi: mvm: Use the sync timepoint API in suspend
+    - mac80211: fix user-power when emulating chanctx
+    - usb: add support for new USB device ID 0x17EF:0x3098 for the r8152 driver
+    - selftests/watchdog-test: Fix system accidentally reset after watchdog-test
+    - ALSA: hda/realtek: Add subwoofer quirk for Infinix ZERO BOOK 13
+    - x86/amd_nb: Fix compile-testing without CONFIG_AMD_NB
+    - net: usb: qmi_wwan: add Quectel RG650V
+    - soc: qcom: Add check devm_kasprintf() returned value
+    - regulator: rk808: Add apply_bit for BUCK3 on RK809
+    - platform/x86: dell-smbios-base: Extends support to Alienware products
+    - platform/x86: dell-wmi-base: Handle META key Lock/Unlock events
+    - can: j1939: fix error in J1939 documentation.
+    - ASoC: stm: Prevent potential division by zero in stm32_sai_mclk_round_rate()
+    - ASoC: stm: Prevent potential division by zero in stm32_sai_get_clk_div()
+    - proc/softirqs: replace seq_printf with seq_put_decimal_ull_width
+    - ALSA: usb-audio: Fix Yamaha P-125 Quirk Entry
+    - ARM: 9420/1: smp: Fix SMP for xip kernels
+    - ipmr: Fix access to mfc_cache_list without lock held
+    - nvme: fix metadata handling in nvme-passthrough
+    - x86/barrier: Do not serialize MSR accesses on AMD
+    - kselftest/arm64: mte: fix printf type warnings about longs
+    - s390/cio: Do not unregister the subchannel based on DNV
+    - brd: remove brd_devices_mutex mutex
+    - mips: asm: fix warning when disabling MIPS_FP_SUPPORT
+    - m68k: mvme147: Fix SCSI controller IRQ numbers
+    - m68k: mvme16x: Add and use "mvme16x.h"
+    - m68k: mvme147: Reinstate early console
+    - arm64: fix .data.rel.ro size assertion when CONFIG_LTO_CLANG
+    - acpi/arm64: Adjust error handling procedure in gtdt_parse_timer_block()
+    - s390/syscalls: Avoid creation of arch/arch/ directory
+    - firmware: google: Unregister driver_info on failure
+    - crypto: qat - remove faulty arbiter config reset
+    - thermal: core: Initialize thermal zones before registering them
+    - EDAC/fsl_ddr: Fix bad bit shift operations
+    - crypto: cavium - Fix the if condition to exit loop after timeout
+    - ACPI: CPPC: Fix _CPC register setting issue
+    - crypto: caam - add error check to caam_rsa_set_priv_key_form
+    - crypto: cavium - Fix an error handling path in cpt_ucode_load_fw()
+    - time: Fix references to _msecs_to_jiffies() handling of values
+    - timekeeping: Consolidate fast timekeeper
+    - seqlock/latch: Provide raw_read_seqcount_latch_retry()
+    - kcsan, seqlock: Support seqcount_latch_t
+    - kcsan, seqlock: Fix incorrect assumption in read_seqbegin()
+    - clocksource/drivers:sp804: Make user selectable
+    - spi: spi-fsl-lpspi: downgrade log level for pio mode
+    - spi: spi-fsl-lpspi: Use IRQF_NO_AUTOEN flag in request_irq()
+    - soc: ti: smartreflex: Use IRQF_NO_AUTOEN flag in request_irq()
+    - mmc: mmc_spi: drop buggy snprintf()
+    - tpm: fix signed/unsigned bug when checking event logs
+    - arm64: dts: mt8183: krane: Fix the address of eeprom at i2c4
+    - arm64: dts: mt8183: kukui: Fix the address of eeprom at i2c4
+    - arm64: dts: mediatek: mt8173-elm-hana: Add vdd-supply to second source
+      trackpad
+    - Revert "cgroup: Fix memory leak caused by missing cgroup_bpf_offline"
+    - cgroup/bpf: only cgroup v2 can be attached by bpf programs
+    - arm64: dts: mt8183: fennel: add i2c2's i2c-scl-internal-delay-ns
+    - arm64: dts: mt8183: burnet: add i2c2's i2c-scl-internal-delay-ns
+    - arm64: dts: mt8183: Damu: add i2c2's i2c-scl-internal-delay-ns
+    - pwm: imx27: Workaround of the pwm output bug when decrease the duty cycle
+    - ARM: dts: cubieboard4: Fix DCDC5 regulator constraints
+    - pmdomain: ti-sci: Add missing of_node_put() for args.np
+    - spi: tegra210-quad: Avoid shift-out-of-bounds
+    - spi: zynqmp-gqspi: Undo runtime PM changes at driver exit time​
+    - regmap: irq: Set lockdep class for hierarchical IRQ domains
+    - arm64: dts: mt8183: jacuzzi: remove unused ddc-i2c-bus
+    - arm64: dts: mt8183: jacuzzi: Move panel under aux-bus
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Fix DP bridge supply names
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add supplies for fixed
+      regulators
+    - selftests/resctrl: Protect against array overrun during iMC config parsing
+    - media: venus: venc: Use pmruntime autosuspend
+    - media: venus: vdec: decoded picture buffer handling during reconfig sequence
+    - media: venus : Addition of EOS Event support for Encoder
+    - media: venus : Addition of support for VIDIOC_TRY_ENCODER_CMD
+    - venus: venc: add handling for VIDIOC_ENCODER_CMD
+    - media: venus: provide ctx queue lock for ioctl synchronization
+    - media: atomisp: remove #ifdef HAS_NO_HMEM
+    - platform/x86: panasonic-laptop: Replace snprintf in show functions with
+      sysfs_emit
+    - platform/x86: panasonic-laptop: Return errno correctly in show callback
+    - drm/mm: Mark drm_mm_interval_tree*() functions with __maybe_unused
+    - drm/omap: Fix possible NULL dereference
+    - drm/omap: Fix locking in omap_gem_new_dmabuf()
+    - wifi: p54: Use IRQF_NO_AUTOEN flag in request_irq()
+    - wifi: mwifiex: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/imx/dcss: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/imx/ipuv3: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/v3d: Address race-condition in MMU flush
+    - wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss1
+    - wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss2
+    - dt-bindings: vendor-prefixes: Add NeoFidelity, Inc
+    - ASoC: fsl_micfil: Drop unnecessary register read
+    - ASoC: fsl_micfil: do not define SHIFT/MASK for single bits
+    - ASoC: fsl_micfil: use GENMASK to define register bit fields
+    - ASoC: fsl_micfil: fix regmap_write_bits usage
+    - ASoC: dt-bindings: mt6359: Update generic node name and dmic-mode
+    - drm/bridge: anx7625: Drop EDID cache on bridge power off
+    - libbpf: Fix output .symtab byte-order during linking
+    - bpf: Fix the xdp_adjust_tail sample prog issue
+    - libbpf: fix sym_is_subprog() logic for weak global subprogs
+    - xfrm: rename xfrm_state_offload struct to allow reuse
+    - xfrm: store and rely on direction to construct offload flags
+    - netdevsim: rely on XFRM state direction instead of flags
+    - netdevsim: copy addresses for both in and out paths
+    - drm/bridge: tc358767: Fix link properties discovery
+    - selftests/bpf: Fix msg_verify_data in test_sockmap
+    - selftests/bpf: Fix txmsg_redir of test_txmsg_pull in test_sockmap
+    - drm: fsl-dcu: enable PIXCLK on LS1021A
+    - drm/panfrost: Remove unused id_mask from struct panfrost_model
+    - drm/msm/adreno: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/etnaviv: Request pages from DMA32 zone on addressing_limited
+    - drm/etnaviv: fix power register offset on GC300
+    - drm/etnaviv: hold GPU lock across perfmon sampling
+    - wifi: wfx: Fix error handling in wfx_core_init()
+    - drm/msm/dpu: cast crtc_clk calculation to u64 in _dpu_core_perf_calc_clk()
+    - netfilter: nf_tables: skip transaction if update object is not implemented
+    - netfilter: nf_tables: must hold rcu read lock while iterating object type
+      list
+    - netlink: typographical error in nlmsg_type constants definition
+    - selftests/bpf: Add txmsg_pass to pull/push/pop in test_sockmap
+    - selftests/bpf: Fix SENDPAGE data logic in test_sockmap
+    - selftests, bpf: Add one test for sockmap with strparser
+    - selftests/bpf: Fix total_bytes in msg_loop_rx in test_sockmap
+    - selftests/bpf: Add push/pop checking for msg_verify_data in test_sockmap
+    - bpf, sockmap: Several fixes to bpf_msg_push_data
+    - bpf, sockmap: Fix sk_msg_reset_curr
+    - selftests: net: really check for bg process completion
+    - drm/amdkfd: Fix wrong usage of INIT_WORK()
+    - net: rfkill: gpio: Add check for clk_enable()
+    - driver core: Introduce device_find_any_child() helper
+    - netpoll: Use rcu_access_pointer() in netpoll_poll_lock
+    - wireguard: selftests: load nf_conntrack if not present
+    - trace/trace_event_perf: remove duplicate samples on the first tracepoint
+      event
+    - pinctrl: zynqmp: drop excess struct member description
+    - powerpc/vdso: Flag VDSO64 entry points as functions
+    - mfd: tps65010: Use IRQF_NO_AUTOEN flag in request_irq() to fix race
+    - mfd: da9052-spi: Change read-mask to write-mask
+    - mfd: intel_soc_pmic_bxtwc: Use dev_err_probe()
+    - cpufreq: loongson2: Unregister platform_driver on failure
+    - mtd: rawnand: atmel: Fix possible memory leak
+    - RDMA/bnxt_re: Check cqe flags to know imm_data vs inv_irkey
+    - clk: imx: lpcg-scu: SW workaround for errata (e10858)
+    - clk: imx: clk-scu: fix clk enable state save and restore
+    - mfd: rt5033: Fix missing regmap_del_irq_chip()
+    - scsi: fusion: Remove unused variable 'rc'
+    - RDMA/hns: Fix out-of-order issue of requester when setting FENCE
+    - powerpc/sstep: make emulate_vsx_load and emulate_vsx_store static
+    - powerpc/kexec: Fix return of uninitialized variable
+    - fbdev/sh7760fb: Alloc DMA memory from hardware device
+    - dt-bindings: clock: axi-clkgen: include AXI clk
+    - clk: clk-axi-clkgen: make sure to enable the AXI bus clock
+    - pinctrl: k210: Undef K210_PC_DEFAULT
+    - mailbox: arm_mhuv2: clean up loop in get_irq_chan_comb()
+    - perf cs-etm: Don't flush when packet_queue fills up
+    - perf probe: Fix libdw memory leak
+    - perf probe: Correct demangled symbols in C++ program
+    - PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
+    - PCI: cpqphp: Fix PCIBIOS_* return value confusion
+    - f2fs: fix the wrong f2fs_bug_on condition in f2fs_do_replace_block
+    - f2fs: remove struct segment_allocation default_salloc_ops
+    - f2fs: open code allocate_segment_by_default
+    - f2fs: remove the unused flush argument to change_curseg
+    - f2fs: check curseg->inited before write_sum_page in change_curseg
+    - perf trace: avoid garbage when not printing a trace event's arguments
+    - m68k: mcfgpio: Fix incorrect register offset for CONFIG_M5441x
+    - m68k: coldfire/device.c: only build FEC when HW macros are defined
+    - perf trace: Do not lose last events in a race
+    - perf trace: Avoid garbage when not printing a syscall's arguments
+    - rpmsg: glink: Add TX_DATA_CONT command while sending
+    - rpmsg: glink: Send READ_NOTIFY command in FIFO full case
+    - rpmsg: glink: Fix GLINK command prefix
+    - rpmsg: glink: use only lower 16-bits of param2 for CMD_OPEN name length
+    - remoteproc: qcom_q6v5_mss: Re-order writes to the IMEM region
+    - NFSD: Cap the number of bytes copied by nfs4_reset_recoverydir()
+    - sunrpc: simplify two-level sysctl registration for svcrdma_parm_table
+    - NFSD: Fix nfsd4_shutdown_copy()
+    - hwmon: (tps23861) Fix reporting of negative temperatures
+    - vdpa/mlx5: Fix suboptimal range on iotlb iteration
+    - selftests/mount_setattr: Fix failures on 64K PAGE_SIZE kernels
+    - fs_parser: update mount_api doc to match function signature
+    - power: supply: core: Remove might_sleep() from power_supply_put()
+    - power: supply: bq27xxx: Fix registers of bq27426
+    - net: usb: lan78xx: Fix memory leak on device unplug by freeing PHY device
+    - tg3: Set coherent DMA mask bits to 31 for BCM57766 chipsets
+    - net: usb: lan78xx: Fix refcounting and autosuspend on invalid WoL
+      configuration
+    - net: mdio-ipq4019: add missing error check
+    - marvell: pxa168_eth: fix call balance of pep->clk handling routines
+    - net: stmmac: dwmac-socfpga: Set RX watchdog interrupt as broken
+    - octeontx2-af: RPM: Fix mismatch in lmac type
+    - spi: atmel-quadspi: Fix register name in verbose logging function
+    - net: hsr: fix hsr_init_sk() vs network/transport headers.
+    - bnxt_en: Reserve rings after PCIe AER recovery if NIC interface is down
+    - iio: light: al3010: Fix an error handling path in al3010_probe()
+    - usb: using mutex lock and supporting O_NONBLOCK flag in iowarrior_read()
+    - usb: yurex: make waiting on yurex_write interruptible
+    - USB: chaoskey: fail open after removal
+    - USB: chaoskey: Fix possible deadlock chaoskey_list_lock
+    - misc: apds990x: Fix missing pm_runtime_disable()
+    - counter: stm32-timer-cnt: Add check for clk_enable()
+    - ALSA: hda/realtek: Update ALC256 depop procedure
+    - apparmor: fix 'Do simple duplicate message elimination'
+    - usb: ehci-spear: fix call balance of sehci clk handling routines
+    - Revert "drivers: clk: zynqmp: update divider round rate logic"
+    - ASoC: Intel: sst: Fix used of uninitialized ctx to log an error
+    - soc: qcom: socinfo: fix revision check in qcom_socinfo_probe()
+    - ext4: supress data-race warnings in ext4_free_inodes_{count,set}()
+    - ext4: fix FS_IOC_GETFSMAP handling
+    - jfs: xattr: check invalid xattr size more strictly
+    - ASoC: codecs: Fix atomicity violation in snd_soc_component_get_drvdata()
+    - perf/x86/intel/pt: Fix buffer full but size is 0 case
+    - crypto: x86/aegis128 - access 32-bit arguments as 32-bit
+    - powerpc/pseries: Fix KVM guest detection for disabling hardlockup detector
+    - KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
+    - fsnotify: fix sending inotify event with unexpected filename
+    - tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler
+    - locking/lockdep: Avoid creating new name string literals in
+      lockdep_set_subclass()
+    - exfat: fix uninit-value in __exfat_get_dentry_set
+    - Bluetooth: Fix type of len in rfcomm_sock_getsockopt{,_old}()
+    - usb: xhci: Fix TD invalidation under pending Set TR Dequeue
+    - Revert "usb: gadget: composite: fix OS descriptors w_value logic"
+    - serial: sh-sci: Clean sci_ports[0] after at earlycon exit
+    - Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"
+    - gpio: exar: set value when external pull-up or pull-down is present
+    - spi: Fix acpi deferred irq probe
+    - mtd: spi-nor: core: replace dummy buswidth from addr to data
+    - cpufreq: mediatek-hw: Fix wrong return value in mtk_cpufreq_get_cpu_power()
+    - platform/chrome: cros_ec_typec: fix missing fwnode reference decrement
+    - ubi: wl: Put source PEB into correct list if trying locking LEB failed
+    - serial: 8250: omap: Move pm_runtime_get_sync
+    - arm64: tls: Fix context-switching of tpidrro_el0 when kpti is enabled
+    - block: fix ordering between checking BLK_MQ_S_STOPPED request adding
+    - HID: wacom: Interpret tilt data from Intuos Pro BT as signed values
+    - soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
+    - media: v4l2-core: v4l2-dv-timings: check cvt/gtf result
+    - ALSA: hda/realtek: Update ALC225 depop procedure
+    - ALSA: hda/realtek: Set PCBeep to default value for ALC274
+    - ALSA: hda/realtek: Fix Internal Speaker and Mic boost of Infinix Y4 Max
+    - ALSA: hda/realtek: Apply quirk for Medion E15433
+    - usb: dwc3: gadget: Fix checking for number of TRBs left
+    - lib: string_helpers: silence snprintf() output truncation warning
+    - rpmsg: glink: Propagate TX failures in intentless mode as well
+    - um: Fix the return value of elf_core_copy_task_fpregs
+    - um: Always dump trace for specified task in show_stack
+    - rtc: st-lpc: Use IRQF_NO_AUTOEN flag in request_irq()
+    - rtc: abx80x: Fix WDT bit position of the status register
+    - ubifs: Correct the total block count by deducting journal reservation
+    - jffs2: fix use of uninitialized variable
+    - block: return unsigned int from bdev_io_min
+    - 9p/xen: fix init sequence
+    - rtc: ab-eoz9: don't fail temperature reads on undervoltage notification
+    - modpost: remove incorrect code in do_eisa_entry()
+    - nfs: ignore SB_RDONLY when mounting nfs
+    - sunrpc: remove unnecessary test in rpc_task_set_client()
+    - SUNRPC: Replace internal use of SOCKWQ_ASYNC_NOSPACE
+    - ASoC: fsl_micfil: fix the naming style for mask definition
+    - xfs: fix log recovery when unknown rocompat bits are set
+    - xfs: remove unknown compat feature check in superblock write validation
+    - btrfs: add might_sleep() annotations
+    - util_macros.h: fix/rework find_closest() macros
+    - scsi: ufs: exynos: Fix hibern8 notify callbacks
+    - PCI: keystone: Add link up check to ks_pcie_other_map_bus()
+    - ovl: properly handle large files in ovl_security_fileattr
+    - dm thin: Add missing destroy_work_on_stack()
+    - PCI: rockchip-ep: Fix address translation unit programming
+    - drm/etnaviv: flush shader L1 cache after user commandstream
+    - iTCO_wdt: mask NMI_NOW bit for update_no_reboot_bit() call
+    - watchdog: mediatek: Make sure system reset gets asserted in
+      mtk_wdt_restart()
+    - can: peak_usb: CANFD: store 64-bits hw timestamps
+    - can: do not increase rx statistics when generating a CAN rx error message
+      frame
+    - can: c_can: c_can_handle_bus_err(): update statistics if skb allocation
+      fails
+    - can: sun4i_can: sun4i_can_err(): call can_change_state() even if cf is NULL
+    - can: m_can: m_can_handle_lec_err(): fix {rx,tx}_errors statistics
+    - can: ifi_canfd: ifi_canfd_handle_lec_err(): fix {rx,tx}_errors statistics
+    - can: sun4i_can: sun4i_can_err(): fix {rx,tx}_errors statistics
+    - can: ems_usb: ems_usb_rx_err(): fix {rx,tx}_errors statistics
+    - ipvs: fix UB due to uninitialized stack access in ip_vs_protocol_init()
+    - ptp: Add error handling for adjfine callback in ptp_clock_adjtime
+    - net/sched: tbf: correct backlog statistic for GSO packets
+    - net/smc: Limit backlog connections
+    - net/qed: allow old cards not supporting "num_images" to work
+    - net: sched: fix erspan_opt settings in cls_flower
+    - netfilter: nft_set_hash: skip duplicated elements pending gc run
+    - netfilter: nft_set_hash: unaligned atomic read on struct nft_set_ext
+    - ethtool: Fix wrong mod state in case of verbose and no_mask bitset
+    - gpio: grgpio: use a helper variable to store the address of ofdev->dev
+    - dt_bindings: rs485: Correct delay values
+    - dt-bindings: serial: rs485: Fix rs485-rts-delay property
+    - serial: amba-pl011: Use port lock wrappers
+    - serial: amba-pl011: Fix RX stall when DMA is used
+    - bpftool: Remove asserts from JIT disassembler
+    - bpftool: fix potential NULL pointer dereferencing in prog_dump()
+    - drm/sti: Add __iomem for mixer_dbg_mxn's parameter
+    - ALSA: pcm: Add more disconnection checks at file ops
+    - ALSA: pcm: Avoid reference to status->state
+    - ALSA: usb-audio: Notify xrun for low-latency mode
+    - tools: Override makefile ARCH variable if defined, but empty
+    - drm/v3d: Enable Performance Counters before clearing them
+    - bpf: Handle BPF_EXIST and BPF_NOEXIST for LPM trie
+    - bpf: Fix exact match conditions in trie_get_next_key()
+    - watchdog: rti: of: honor timeout-sec property
+    - tracing: Fix cmp_entries_dup() to respect sort() comparison rules
+    - ALSA: usb-audio: add mixer mapping for Corsair HS80
+    - ALSA: hda/realtek: Enable mute and micmute LED on HP ProBook 430 G8
+    - ALSA: hda/realtek: Add support for Samsung Galaxy Book3 360 (NP730QFG)
+    - scsi: qla2xxx: Fix abort in bsg timeout
+    - scsi: qla2xxx: Fix NVMe and NPIV connect issue
+    - scsi: qla2xxx: Supported speed displayed incorrectly for VPorts
+    - scsi: qla2xxx: Remove check req_sg_cnt should be equal to rsp_sg_cnt
+    - dma-buf: fix dma_fence_array_signaled v4
+    - regmap: detach regmap from dev on regmap_exit
+    - mmc: sdhci-pci: Add DMI quirk for missing CD GPIO on Vexia Edu Atla 10
+      tablet
+    - mmc: core: Further prevent card detect during shutdown
+    - ocfs2: update seq_file index in ocfs2_dlm_seq_next
+    - epoll: annotate racy check
+    - btrfs: avoid unnecessary device path update for the same device
+    - kselftest/arm64: Don't leak pipe fds in pac.exec_sign_all()
+    - media: uvcvideo: Add a quirk for the Kaiweets KTI-W02 infrared camera
+    - media: cx231xx: Add support for Dexatek USB Video Grabber 1d19:6108
+    - drm/vc4: hvs: Set AXI panic modes for the HVS
+    - drm: panel-orientation-quirks: Add quirk for AYA NEO 2 model
+    - drm/mcde: Enable module autoloading
+    - drm/radeon/r600_cs: Fix possible int overflow in r600_packet3_check()
+    - r8169: don't apply UDP padding quirk on RTL8126A
+    - samples/bpf: Fix a resource leak
+    - net: fec_mpc52xx_phy: Use %pa to format resource_size_t
+    - net: ethernet: fs_enet: Use %pa to format resource_size_t
+    - net/sched: cbs: Fix integer overflow in cbs_set_port_rate()
+    - Bluetooth: L2CAP: handle NULL sock pointer in l2cap_sock_alloc
+    - wifi: ath5k: add PCI ID for SX76X
+    - wifi: ath5k: add PCI ID for Arcadyan devices
+    - drm/panel: simple: Add Microchip AC69T88A LVDS Display panel
+    - drm/amdgpu: clear RB_OVERFLOW bit when enabling interrupts for vega20_ih
+    - drm/amdgpu: Dereference the ATCS ACPI buffer
+    - drm/amdgpu: refine error handling in amdgpu_ttm_tt_pin_userptr
+    - drm/amdgpu: skip amdgpu_device_cache_pci_state under sriov
+    - wifi: ipw2x00: libipw_rx_any(): fix bad alignment
+    - ASoC: hdmi-codec: reorder channel allocation list
+    - rocker: fix link status detection in rocker_carrier_init()
+    - net/neighbor: clear error in case strict check is not set
+    - netpoll: Use rcu_access_pointer() in __netpoll_setup
+    - pinctrl: freescale: fix COMPILE_TEST error with PINCTRL_IMX_SCU
+    - tracing: Use atomic64_inc_return() in trace_clock_counter()
+    - scsi: st: Don't modify unknown block number in MTIOCGET
+    - scsi: st: Add MTIOCGET and MTLOAD to ioctls allowed after device reset
+    - pinctrl: qcom-pmic-gpio: add support for PM8937
+    - nvdimm: rectify the illogical code within nd_dax_probe()
+    - PCI: Detect and trust built-in Thunderbolt chips
+    - PCI: Add 'reset_subordinate' to reset hierarchy below bridge
+    - PCI: Add ACS quirk for Wangxun FF5xxx NICs
+    - usb: chipidea: udc: handle USB Error Interrupt if IOC not set
+    - misc: eeprom: eeprom_93cx6: Add quirk for extra read clock cycle
+    - modpost: Include '.text.*' in TEXT_SECTIONS
+    - modpost: Add .irqentry.text to OTHER_SECTIONS
+    - sched/core: Remove the unnecessary need_resched() check in nohz_csd_func()
+    - sched/fair: Add NOHZ balancer flag for nohz.next_balance updates
+    - sched/fair: Check idle_cpu() before need_resched() to detect ilb CPU turning
+      busy
+    - sched/core: Prevent wakeup of ksoftirqd during idle load balance
+    - btrfs: fix missing snapshot drew unlock when root is dead during swap
+      activation
+    - tracing/eprobe: Fix to release eprobe when failed to add dyn_event
+    - Revert "unicode: Don't special case ignorable code points"
+    - KVM: arm64: vgic-its: Add a data length check in vgic_its_save_*
+    - KVM: arm64: vgic-its: Clear DTE when MAPD unmaps a device
+    - KVM: arm64: vgic-its: Clear ITE when DISCARD frees an ITE
+    - jffs2: Fix rtime decompressor
+    - mm/damon/vaddr-test: split a test function having >1024 bytes frame size
+    - mm/damon/vaddr: fix issue in damon_va_evenly_split_region()
+    - xhci: dbc: Fix STALL transfer event handling
+    - mmc: mtk-sd: Fix error handle of probe function
+    - ocfs2: Revert "ocfs2: fix the la space leak when unmounting an ocfs2 volume"
+    - Revert "drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()"
+    - scsi: core: Fix scsi_mode_select() buffer length handling
+    - gve: Fixes for napi_poll when budget is 0
+    - arm64: smccc: Remove broken support for SMCCCv1.3 SVE discard hint
+    - net: dsa: microchip: correct KSZ8795 static MAC table access
+    - drm/amdgpu: rework resume handling for display (v2)
+    - serial: amba-pl011: fix build regression
+    - media: venus: vdec: fixed possible memory leak issue
+    - net/smc: Fix af_ops of child socket pointing to released memory
+    - Bluetooth: hci_core: Fix calling mgmt_device_connected
+    - Linux 5.15.174
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46871
+    - drm/amd/display: Correct the defined value for AMDGPU_DMUB_NOTIFICATION_MAX
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49950
+    - Bluetooth: L2CAP: Fix uaf in l2cap_connect
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50275
+    - arm64/sve: Discard stale CPU state when handling SVE traps
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-47730
+    - crypto: hisilicon/qm - inject error before stopping queue
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46809
+    - drm/amd/display: Check BIOS images before it is used
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57850
+    - jffs2: Prevent rtime decompress memory corruption
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56781
+    - powerpc/prom_init: Fixup missing powermac #size-cells
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56785
+    - MIPS: Loongson64: DTS: Really fix PCIe port nodes for ls7a
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-43098
+    - i3c: Use i3cdev->desc->info instead of calling i3c_device_get_info() to
+      avoid deadlock
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-45828
+    - i3c: mipi-i3c-hci: Mask ring interrupts before ring stop request
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56586
+    - f2fs: fix f2fs_bug_on when uninstalling filesystem call f2fs_evict_inode.
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56587
+    - leds: class: Protect brightness_show() with led_cdev->led_access mutex
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56589
+    - scsi: hisi_sas: Add cond_resched() for no forced preemption model
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56590
+    - Bluetooth: hci_core: Fix not checking skb length on hci_acldata_packet
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56593
+    - wifi: brcmfmac: Fix oops due to NULL pointer dereference in
+      brcmf_sdiod_sglist_rw()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56594
+    - drm/amdgpu: set the right AMDGPU sg segment limitation
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56595
+    - jfs: add a check to prevent array-index-out-of-bounds in dbAdjTree
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56596
+    - jfs: fix array-index-out-of-bounds in jfs_readdir
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56597
+    - jfs: fix shift-out-of-bounds in dbSplit
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56598
+    - jfs: array-index-out-of-bounds fix in dtReadFirst
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-47143
+    - dma-debug: fix a possible deadlock on radix_lock
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56600
+    - net: inet6: do not leave a dangling sk pointer in inet6_create()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56601
+    - net: inet: do not leave a dangling sk pointer in inet_create()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56602
+    - net: ieee802154: do not leave a dangling sk pointer in ieee802154_create()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56603
+    - net: af_can: do not leave a dangling sk pointer in can_create()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56605
+    - Bluetooth: L2CAP: do not leave dangling sk pointer on error in
+      l2cap_sock_create()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56606
+    - af_packet: avoid erroring out after sock_init_data() in packet_create()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56787
+    - soc: imx8m: Probe the SoC driver as platform driver
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56610
+    - kcsan: Turn report_filterlist_lock into a raw_spinlock
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57849
+    - s390/cpum_sf: Handle CPU hotplug remove during sampling
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56568
+    - iommu/arm-smmu: Defer probe of clients after smmu device bound
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56614
+    - xsk: fix OOB map writes when deleting elements
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56615
+    - bpf: fix OOB devmap writes when deleting elements
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-48881
+    - bcache: revert replacing IS_ERR_OR_NULL with IS_ERR again
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56619
+    - nilfs2: fix potential out-of-bounds memory access in nilfs_find_entry()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56622
+    - scsi: ufs: core: sysfs: Prevent div by zero
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56623
+    - scsi: qla2xxx: Fix use after free on unload
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57874
+    - arm64: ptrace: fix partial SETREGSET for NT_ARM_TAGGED_ADDR_CTRL
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56625
+    - can: dev: can_set_termination(): allow sleeping GPIOs
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56629
+    - HID: wacom: fix when get product name maybe null pointer
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56630
+    - ocfs2: free inode when ocfs2_get_init_inode() fails
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50051
+    - spi: mpc52xx: Add cancel_work_sync before module remove
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56633
+    - tcp_bpf: Fix the sk_mem_uncharge logic in tcp_bpf_sendmsg
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56634
+    - gpio: grgpio: Add NULL check in grgpio_probe
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56636
+    - geneve: do not assume mac header is set in geneve_xmit_skb()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56637
+    - netfilter: ipset: Hold module reference while requesting a module
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-52332
+    - igb: Fix potential invalid memory access in igb_init_module()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56640
+    - net/smc: fix LGR and link use-after-free issue
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56642
+    - tipc: Fix use-after-free of kernel socket in cleanup_bearer().
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56643
+    - dccp: Fix memory leak in dccp_feat_change_recv
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56644
+    - net/ipv6: release expired exception dst cached in socket
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56645
+    - can: j1939: j1939_session_new(): fix skb reference counting
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56648
+    - net: hsr: avoid potential out-of-bound access in fill_frame_info()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56650
+    - netfilter: x_tables: fix LED ID check in led_tg_check()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56776
+    - drm/sti: avoid potential dereference of error pointers
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56777
+    - drm/sti: avoid potential dereference of error pointers in
+      sti_gdp_atomic_check
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56778
+    - drm/sti: avoid potential dereference of error pointers in
+      sti_hqvdp_atomic_check
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46841
+    - btrfs: don't BUG_ON on ENOMEM from btrfs_lookup_extent_info() in
+      walk_down_proc()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56779
+    - nfsd: fix nfs4_openowner leak when concurrent nfsd4_open occur
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56558
+    - nfsd: make sure exp active before svc_export_show
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56562
+    - i3c: master: Fix miss free init_dyn_addr at i3c_master_put_i3c_addrs()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57838
+    - s390/entry: Mark IRQ entries to fix stack depot warnings
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56567
+    - ad7780: fix division by zero in ad7780_write_raw()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56581
+    - btrfs: ref-verify: fix use-after-free after invalid ref action
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56774
+    - btrfs: add a sanity check for btrfs root in btrfs_search_slot()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56780
+    - quota: flush quota_release_work upon quota writeback
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53165
+    - sh: intc: Fix use-after-free bug in register_intc_controller()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56688
+    - sunrpc: clear XPRT_SOCK_UPD_TIMEOUT when reset transport
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56704
+    - 9p/xen: fix release of IRQ
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53171
+    - ubifs: authentication: Fix use-after-free in ubifs_tnc_end_commit
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53172
+    - ubi: fastmap: Fix duplicate slab cache names while attaching
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56739
+    - rtc: check if __rtc_read_time was successful in rtc_timer_do_work()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53173
+    - NFSv4.0: Fix a use-after-free problem in the asynchronous open()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53145
+    - um: Fix potential integer overflow during physmem setup
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53174
+    - SUNRPC: make sure cache entry active before cache_show
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53146
+    - NFSD: Prevent a potential integer overflow
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56698
+    - usb: dwc3: gadget: Fix looping of queued SG entries
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53180
+    - ALSA: pcm: Add sanity NULL check for the default mmap fault handler
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56700
+    - media: wl128x: Fix atomicity violation in fmc_send_cmd()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2022-49034
+    - sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53181
+    - um: vector: Do not use drvdata in release
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53183
+    - um: net: Do not use drvdata in release
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53184
+    - um: ubd: Do not use drvdata in release
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50055
+    - driver core: bus: Fix double free in driver API bus_register()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56741
+    - apparmor: test: Fix memory leak for aa_unpack_strdup()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53148
+    - comedi: Flush partial mappings in error case
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53194
+    - PCI: Fix use-after-free of slot->bus on hot remove
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53197
+    - ALSA: usb-audio: Fix potential out-of-bound accesses for Extigy and Mbox
+      devices
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53150
+    - ALSA: usb-audio: Fix out of bounds reads when finding clock sources
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53198
+    - xen: Fix the issue of resource not being properly released in
+      xenbus_dev_probe()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50283
+    - ksmbd: fix slab-use-after-free in smb3_preauth_hash_rsp
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53206
+    - tcp: Fix use-after-free of nreq in reqsk_timer_handler().
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53214
+    - vfio/pci: Properly hide first-in-list PCIe extended capability
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53215
+    - svcrdma: fix miss destroy percpu_counter in svc_rdma_proc_init()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53217
+    - NFSD: Prevent NULL dereference in nfsd4_process_cb_update()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53151
+    - svcrdma: Address an integer overflow
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56745
+    - PCI: Fix reset_method_store() memory leak
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56746
+    - fbdev: sh7760fb: Fix a possible memory leak in sh7760fb_alloc_mem()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53155
+    - ocfs2: fix uninitialized value in ocfs2_file_read_iter()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53226
+    - RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56747
+    - scsi: qedi: Fix a possible memory leak in qedi_alloc_and_init_sb()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56748
+    - scsi: qedf: Fix a possible memory leak in qedf_alloc_and_init_sb()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53227
+    - scsi: bfa: Fix use-after-free in bfad_im_module_exit()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56701
+    - powerpc/pseries: Fix dtl_access_lock to be a rw_semaphore
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56678
+    - powerpc/mm/fault: Fix kfence page fault reporting
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56723
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for PMIC devices
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56724
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for TMU device
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56691
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for USB Type-C device
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56694
+    - bpf: fix recursive lock when verdict program return SK_PASS
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53237
+    - Bluetooth: fix use-after-free in device_for_each_child()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53239
+    - ALSA: 6fire: Release resources at card release
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56531
+    - ALSA: caiaq: Use snd_card_free_when_closed() at disconnection
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56532
+    - ALSA: us122l: Use snd_card_free_when_closed() at disconnection
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56533
+    - ALSA: usx2y: Use snd_card_free_when_closed() at disconnection
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56720
+    - bpf, sockmap: Several fixes to bpf_msg_pop_data
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56726
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in cn10k.c
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56728
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_ethtool.c
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56679
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_common.c
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56539
+    - wifi: mwifiex: Fix memcpy() field-spanning write warning in
+      mwifiex_config_scan()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53156
+    - wifi: ath9k: add range check for conn_rsp_epid in htc_connect_service()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56705
+    - media: atomisp: Add check for rgby_data memory allocation failure
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53157
+    - firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53158
+    - soc: qcom: geni-se: fix array underflow in geni_se_clk_tbl_get()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56681
+    - crypto: bcm - add error check in the ahash_hmac_init function
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56708
+    - EDAC/igen6: Avoid segmentation fault on module unload
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56690
+    - crypto: pcrypt - Call crypto layer directly when padata_do_parallel() return
+      -EBUSY
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53161
+    - EDAC/bluefield: Fix potential integer overflow
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56754
+    - crypto: caam - Fix the pointer passed to caam_qi_shutdown()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56548
+    - hfsplus: don't query the device logical block size multiple times
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56756
+    - nvme-pci: fix freeing of the HMB descriptor table
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53142
+    - initramfs: avoid filename buffer overrun
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56693
+    - brd: defer automatic disk creation until module initialization succeeds
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49996
+    - cifs: Fix buffer overflow when parsing NFS reparse points
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53096
+    - mm: resolve faulty mmap_region() error path behaviour
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53122
+    - mptcp: cope racing subflow creation in mptcp_rcv_space_adjust
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49974
+    - NFSD: Limit the number of concurrent async COPY operations
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53127
+    - Revert "mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K"
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53130
+    - nilfs2: fix null-ptr-deref in block_dirty_buffer tracepoint
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53131
+    - nilfs2: fix null-ptr-deref in block_touch_buffer tracepoint
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53135
+    - KVM: VMX: Bury Intel PT virtualization (guest/host mode) behind
+      CONFIG_BROKEN
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53112
+    - ocfs2: uncache inode which has failed entering the group
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53113
+    - mm: fix NULL pointer dereference in alloc_pages_bulk_noprof
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53120
+    - net/mlx5e: CT: Fix null-ptr-deref in add rule err flow
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53138
+    - net/mlx5e: kTLS, Fix incorrect page refcounting
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53121
+    - net/mlx5: fs, lock FTE when checking if active
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53129
+    - drm/rockchip: vop: Fix a dereferenced before check warning
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53140
+    - netlink: terminate outstanding dump on socket close
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56569
+    - ftrace: Fix regression with module command in stack_trace_filter
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56570
+    - ovl: Filter invalid inodes with missing lookup function
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56572
+    - media: platform: allegro-dvt: Fix possible memory leak in
+      allocate_buffers_internal()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56574
+    - media: ts2020: fix null-ptr-deref in ts2020_probe()
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56575
+    - media: imx-jpeg: Ensure power suppliers be suspended before detach them
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56576
+    - media: i2c: tc358743: Fix crash in the probe error path when using polling
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56578
+    - media: imx-jpeg: Set video drvdata before register video device
+
+  * CVE-2024-56672
+    - blk-cgroup: Fix UAF in blkcg_unpin_online()
+
+ -- Mehmet Basaran <mehmet.basaran@canonical.com>  Fri, 14 Feb 2025 15:34:34 +0300
+
+linux (5.15.0-133.144) jammy; urgency=medium
+
+  * CVE-2025-0927
+    - SAUCE: fs: hfs/hfsplus: add key_len boundary check to hfs_bnode_read_key
+
+ -- Manuel Diewald <manuel.diewald@canonical.com>  Fri, 07 Feb 2025 18:44:33 +0100
+
+linux (5.15.0-132.143) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-132.143 -proposed tracker (LP: #2093735)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.01.13)
+
+  * KVM: Cache CPUID at KVM.ko module init to reduce latency of VM-Enter and VM-
+    Exit (LP: #2093146)
+    - kvm: x86: Fix xstate_required_size() to follow XSTATE alignment rule
+    - KVM: x86: Cache CPUID.0xD XSTATE offsets+sizes during module init
+
+  * Jammy update: v5.15.173 upstream stable release (LP: #2089541)
+    - 9p: Avoid creating multiple slab caches with the same name
+    - irqchip/ocelot: Fix trigger register address
+    - block: Fix elevator_get_default() checking for NULL q->tag_set
+    - HID: multitouch: Add support for B2402FVA track point
+    - HID: multitouch: Add quirk for HONOR MagicBook Art 14 touchpad
+    - bpf: use kvzmalloc to allocate BPF verifier environment
+    - crypto: marvell/cesa - Disable hash algorithms
+    - sound: Make CONFIG_SND depend on INDIRECT_IOMEM instead of UML
+    - drm/vmwgfx: Limit display layout ioctl array size to
+      VMWGFX_NUM_DISPLAY_UNITS
+    - powerpc/powernv: Free name on error in opal_event_init()
+    - vDPA/ifcvf: Fix pci_read_config_byte() return code handling
+    - fs: Fix uninitialized value issue in from_kuid and from_kgid
+    - HID: multitouch: Add quirk for Logitech Bolt receiver w/ Casa touchpad
+    - HID: lenovo: Add support for Thinkpad X1 Tablet Gen 3 keyboard
+    - net: usb: qmi_wwan: add Fibocom FG132 0x0112 composition
+    - md/raid10: improve code of mrdev in raid10_sync_request
+    - mm/memory: add non-anonymous page check in the copy_present_page()
+    - udf: Allocate name buffer in directory iterator on heap
+    - udf: Avoid directory type conversion failure due to ENOMEM
+    - 9p: fix slab cache name creation for real
+    - Linux 5.15.173
+
+  * Jammy update: v5.15.173 upstream stable release (LP: #2089541) //
+    CVE-2024-41080
+    - io_uring: fix possible deadlock in io_register_iowq_max_workers()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533)
+    - arm64: dts: rockchip: Fix rt5651 compatible value on rk3399-sapphire-
+      excavator
+    - arm64: dts: rockchip: Remove hdmi's 2nd interrupt on rk3328
+    - arm64: dts: rockchip: Fix bluetooth properties on Rock960 boards
+    - arm64: dts: rockchip: Remove #cooling-cells from fan on Theobroma lion
+    - arm64: dts: rockchip: Fix LED triggers on rk3308-roc-cc
+    - arm64: dts: imx8mp: correct sdhc ipg clk
+    - ARM: dts: rockchip: fix rk3036 acodec node
+    - ARM: dts: rockchip: drop grf reference from rk3036 hdmi
+    - ARM: dts: rockchip: Fix the spi controller on rk3036
+    - ARM: dts: rockchip: Fix the realtek audio codec on rk3036-kylin
+    - NFSv3: only use NFS timeout for MOUNT when protocols are compatible
+    - NFS: Add a tracepoint to show the results of nfs_set_cache_invalid()
+    - NFSv3: handle out-of-order write replies.
+    - nfs: avoid i_lock contention in nfs_clear_invalid_mapping
+    - net: enetc: set MAC address to the VF net_device
+    - can: c_can: fix {rx,tx}_errors statistics
+    - net: phy: ti: add PHY_RST_AFTER_CLK_EN flag
+    - net: stmmac: Fix unbalanced IRQ wake disable warning on single irq case
+    - Revert "ALSA: hda/conexant: Mute speakers at suspend / shutdown"
+    - media: stb0899_algo: initialize cfr before using it
+    - media: dvb_frontend: don't play tricks with underflow values
+    - media: adv7604: prevent underflow condition when reporting colorspace
+    - scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
+    - ALSA: firewire-lib: fix return value on fail in amdtp_tscm_init()
+    - media: pulse8-cec: fix data timestamp at pulse8_setup()
+    - media: v4l2-ctrls-api: fix error handling for v4l2_g_ctrl()
+    - pwm: imx-tpm: Use correct MODULO value for EPWM mode
+    - drm/amdgpu: Adjust debugfs eviction and IB access permissions
+    - drm/amdgpu: prevent NULL pointer dereference if ATIF is not supported
+    - thermal/drivers/qcom/lmh: Remove false lockdep backtrace
+    - dm cache: correct the number of origin blocks to match the target length
+    - dm cache: optimize dirty bit checking with find_next_bit when resizing
+    - dm-unstriped: cast an operand to sector_t to prevent potential uint32_t
+      overflow
+    - ALSA: usb-audio: Add quirk for HP 320 FHD Webcam
+    - posix-cpu-timers: Clear TICK_DEP_BIT_POSIX_TIMER on clone
+    - io_uring: rename kiocb_end_write() local helper
+    - fs: create kiocb_{start,end}_write() helpers
+    - io_uring: use kiocb_{start,end}_write() helpers
+    - media: uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in
+      uvc_parse_format
+    - fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
+    - usb: dwc3: fix fault at system suspend if device was already runtime
+      suspended
+    - USB: serial: qcserial: add support for Sierra Wireless EM86xx
+    - USB: serial: option: add Fibocom FG132 0x0112 composition
+    - USB: serial: option: add Quectel RG650V
+    - irqchip/gic-v3: Force propagation of the active state with a read-back
+    - ucounts: fix counter leak in inc_rlimit_get_ucounts()
+    - ALSA: usb-audio: Support jack detection on Dell dock
+    - ALSA: usb-audio: Add quirks for Dell WD19 dock
+    - ACPI: PRM: Clean up guid type in struct prm_handler_info
+    - ALSA: usb-audio: Add endianness annotations
+    - Linux 5.15.172
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50265
+    - ocfs2: remove entry once instead of null-ptr-dereference in
+      ocfs2_xa_remove()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50267
+    - USB: serial: io_edgeport: fix use after free in debug printk
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50268
+    - usb: typec: fix potential out of bounds in ucsi_ccg_update_set_new_cam_cmd()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50269
+    - usb: musb: sunxi: Fix accessing an released usb phy
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50036
+    - net: do not delay dst_entries_add() in dst_release()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-42291
+    - ice: Add a per-VF limit on number of FDIR filters
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50273
+    - btrfs: reinitialize delayed ref list after deleting it from the list
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53066
+    - nfs: Fix KMSAN warning in decode_getfattr_attrs()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53052
+    - io_uring/rw: fix missing NOWAIT check for O_DIRECT start write
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50278
+    - dm cache: fix potential out-of-bounds access on the first resume
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50279
+    - dm cache: fix out-of-bounds access to the dirty bitset when resizing
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50282
+    - drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50287
+    - media: v4l2-tpg: prevent the risk of a division by zero
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50290
+    - media: cx24116: prevent overflows on SNR calculus
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53061
+    - media: s5p-jpeg: prevent buffer overflows
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50292
+    - ASoC: stm32: spdifrx: fix dma channel release in stm32_spdifrx_remove
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53063
+    - media: dvbdev: prevent the risk of out of memory access
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50295
+    - net: arc: fix the device for dma_map_single/dma_unmap_single
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50296
+    - net: hns3: fix kernel crash when uninstalling driver
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53088
+    - i40e: fix race condition by adding filter's intermediate sync state
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50299
+    - sctp: properly validate chunk size in sctp_sf_ootb()
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50301
+    - security/keys: fix slab-out-of-bounds in key_task_permission
+
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50302
+    - HID: core: zero-initialize the report buffer
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405)
+    - selftests/mm: fix incorrect buffer->mirror size in hmm2 double_map test
+    - ACPI: PRM: Remove unnecessary blank lines
+    - ACPI: PRM: Change handler_addr type to void pointer
+    - cgroup: Fix potential overflow issue when checking max_depth
+    - mac80211: MAC80211_MESSAGE_TRACING should depend on TRACING
+    - wifi: mac80211: skip non-uploaded keys in ieee80211_iter_keys
+    - wifi: brcm80211: BRCM_TRACING should depend on TRACING
+    - RDMA/cxgb4: Dump vendor specific QP details
+    - RDMA/mlx5: Round max_rd_atomic/max_dest_rd_atomic up instead of down
+    - RDMA/bnxt_re: synchronize the qp-handle table array
+    - mac80211: do drv_reconfig_complete() before restarting all
+    - mac80211: Add support to trigger sta disconnect on hardware restart
+    - wifi: iwlwifi: mvm: disconnect station vifs if recovery failed
+    - ASoC: cs42l51: Fix some error handling paths in cs42l51_probe()
+    - gtp: allow -1 to be specified as file description from userspace
+    - net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension
+    - firmware: arm_sdei: Fix the input parameter of cpuhp_remove_state()
+    - fs/ntfs3: Fix warning possible deadlock in ntfs_set_state
+    - scsi: scsi_transport_fc: Allow setting rport state to current state
+    - net: amd: mvme147: Fix probe banner message
+    - NFS: remove revoked delegation from server's delegation list
+    - misc: sgi-gru: Don't disable preemption in GRU driver
+    - usbip: tools: Fix detach_port() invalid port error path
+    - usb: phy: Fix API devm_usb_put_phy() can not release the phy
+    - usb: typec: fix unreleased fwnode_handle in typec_port_register_altmodes()
+    - xhci: Fix Link TRB DMA in command ring stopped completion event
+    - xhci: Use pm_runtime_get to prevent RPM on unsupported systems
+    - Revert "driver core: Fix uevent_show() vs driver detach race"
+    - iio: light: veml6030: fix microlux value calculation
+    - riscv: vdso: Prevent the compiler from inserting calls to memset()
+    - riscv: efi: Set NX compat flag in PE/COFF header
+    - riscv: Use '%u' to format the output of 'cpu'
+    - riscv: Remove unused GENERATING_ASM_OFFSETS
+    - riscv: Remove duplicated GET_RM
+    - mm/page_alloc: call check_new_pages() while zone spinlock is not held
+    - mm/page_alloc: fix tracepoint mm_page_alloc_zone_locked()
+    - mm/page_alloc: split out buddy removal code from rmqueue into separate
+      helper
+    - mm/page_alloc: rename ALLOC_HIGH to ALLOC_MIN_RESERVE
+    - mm/page_alloc: treat RT tasks similar to __GFP_HIGH
+    - mm/page_alloc: explicitly record high-order atomic allocations in
+      alloc_flags
+    - mm/page_alloc: explicitly define what alloc flags deplete min reserves
+    - mm/page_alloc: explicitly define how __GFP_HIGH non-blocking allocations
+      accesses reserves
+    - Revert "drm/mipi-dsi: Set the fwnode for mipi_dsi_device"
+    - vt: prevent kernel-infoleak in con_font_get()
+    - mac80211: always have ieee80211_sta_restart()
+    - Linux 5.15.171
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2023-52913
+    - drm/i915: Fix potential context UAFs
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50228
+    - mm: shmem: fix data-race in shmem_getattr()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53055
+    - wifi: iwlwifi: mvm: fix 6 GHz scan construction
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50230
+    - nilfs2: fix kernel bug due to missing clearing of checked flag
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50072
+    - x86/bugs: Use code segment selector for VERW operand
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50218
+    - ocfs2: pass u64 to ocfs2_truncate_inline maybe overflow
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50219
+    - mm/page_alloc: let GFP_ATOMIC order-0 allocs access highatomic reserves
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50229
+    - nilfs2: fix potential deadlock with newly created symlinks
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50232
+    - iio: adc: ad7124: fix division by zero in ad7124_set_channel_odr()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50233
+    - staging: iio: frequency: ad9832: fix division by zero in
+      ad9832_calc_freqreg()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50234
+    - wifi: iwlegacy: Clear stale interrupts before resuming device
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50236
+    - wifi: ath10k: Fix memory leak in management tx
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50237
+    - wifi: mac80211: do not pass a stopped vif to the driver in .get_txpower
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50244
+    - fs/ntfs3: Additional check in ni_clear()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50245
+    - fs/ntfs3: Fix possible deadlock in mi_read
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50247
+    - fs/ntfs3: Check if more than chunk-size bytes are written
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50249
+    - ACPI: CPPC: Make rmw_lock a raw_spin_lock
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50251
+    - netfilter: nft_payload: sanitize offset and length before calling
+      skb_checksum()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50257
+    - netfilter: Fix use-after-free in get_info()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50262
+    - bpf: Fix out-of-bounds write in trie_get_next_key()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50259
+    - netdevsim: Add trailing zero to terminate the string in
+      nsim_nexthop_bucket_activity_write()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53042
+    - ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_init_flow()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53058
+    - net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53059
+    - wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50141
+    - ACPI: PRM: Find EFI_MEMORY_RUNTIME block for PRM handler and context
+
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50086
+    - ksmbd: fix user-after-free from session log off
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272)
+    - RDMA/bnxt_re: Fix incorrect AVID type in WQE structure
+    - x86/resctrl: Avoid overflow in MB settings in bw_validate()
+    - ARM: dts: bcm2837-rpi-cm3-io3: Fix HDMI hpd-gpio pin
+    - RDMA/cxgb4: Fix RDMA_CM_EVENT_UNREACHABLE error for iWARP
+    - RDMA/irdma: Fix misspelling of "accept*"
+    - ipv4: give an IPv4 dev to blackhole_netdev
+    - RDMA/bnxt_re: Return more meaningful error
+    - drm/msm/dsi: fix 32-bit signed integer extension in pclk_rate calculation
+    - drm/msm: Allocate memory for disp snapshot with kvzalloc()
+    - net: usb: usbnet: fix race in probe failure
+    - octeontx2-af: Fix potential integer overflows on integer shifts
+    - macsec: don't increment counters for an unrelated SA
+    - net: ethernet: aeroflex: fix potential memory leak in
+      greth_start_xmit_gbit()
+    - net/smc: Fix searching in list of known pnetids in smc_pnet_add_pnetid
+    - net: xilinx: axienet: fix potential memory leak in axienet_start_xmit()
+    - genetlink: hold RCU in genlmsg_mcast()
+    - s390: Initialize psw mask in perf_arch_fetch_caller_regs()
+    - arm64:uprobe fix the uprobe SWBP_INSN in big-endian
+    - KVM: s390: gaccess: Check if guest address is in memslot
+    - usb: gadget: Add function wakeup support
+    - XHCI: Separate PORT and CAPs macros into dedicated file
+    - usb: dwc3: core: Fix system suspend on TI AM62 platforms
+    - block, bfq: fix procress reference leakage for bfqq in merge chain
+    - ASoC: codecs: lpass-rx-macro: add missing CDC_RX_BCL_VBAT_RF_PROC2 to
+      default regs values
+    - ASoC: fsl_sai: Enable 'FIFO continue on error' FCONT bit
+    - arm64: Force position-independent veneers
+    - platform/x86: dell-wmi: Ignore suspend notifications
+    - arm64/uprobes: change the uprobe_opcode_t typedef to fix the sparse warning
+    - ASoC: qcom: sm8250: add qrb4210-rb2-sndcard compatible string
+    - platform/x86: dell-sysman: add support for alienware products
+    - jfs: Fix sanity check in dbMount
+    - xfrm: extract dst lookup parameters into a struct
+    - xfrm: respect ip protocols rules criteria when performing dst lookups
+    - net: plip: fix break; causing plip to never transmit
+    - net: dsa: mv88e6xxx: Fix error when setting port policy on mv88e6393x
+    - net: usb: usbnet: fix name regression
+    - r8169: avoid unsolicited interrupts
+    - posix-clock: posix-clock: Fix unbalanced locking in pc_clock_settime()
+    - bpf,perf: Fix perf_event_detach_bpf_prog error handling
+    - ALSA: hda/realtek: Update default depop procedure
+    - btrfs: zoned: fix zone unusable accounting for freed reserved extent
+    - ACPI: resource: Add LG 16T90SP to irq1_level_low_skip_override[]
+    - ACPI: button: Add DMI quirk for Samsung Galaxy Book2 to fix initial lid
+      detection issue
+    - openat2: explicitly return -E2BIG for (usize > PAGE_SIZE)
+    - ALSA: hda/realtek: Add subwoofer quirk for Acer Predator G9-593
+    - hv_netvsc: Fix VF namespace also in synthetic NIC NETDEV_REGISTER event
+    - selinux: improve error checking in sel_write_load()
+    - net: phy: dp83822: Fix reset pin definitions
+    - Linux 5.15.170
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50142
+    - xfrm: validate new SA's prefixlen using SA family when sel.family is unset
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50103
+    - ASoC: qcom: Fix NULL Dereference in asoc_qcom_lpass_cpu_platform_probe()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50058
+    - serial: protect uart_port_dtr_rts() in uart_shutdown() too
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50110
+    - xfrm: fix one more kernel-infoleak in algo dumping
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50115
+    - KVM: nSVM: Ignore nCR3[4:0] when loading PDPTEs from memory
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50116
+    - nilfs2: fix kernel bug due to missing clearing of buffer delay flag
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50117
+    - drm/amd: Guard against bad data for ATIF ACPI method
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50205
+    - ALSA: firewire-lib: Avoid division by zero in apply_constraint_to_size()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50127
+    - net: sched: fix use-after-free in taprio_change()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50128
+    - net: wwan: fix global oob in wwan_rtnl_policy
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50167
+    - be2net: fix potential memory leak in be_xmit()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50168
+    - net/sun3_82586: fix potential memory leak in sun3_82586_send_packet()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50131
+    - tracing: Consider the NULL character when validating the event length
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50143
+    - udf: fix uninit-value use in udf_get_fileshortad
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50134
+    - drm/vboxvideo: Replace fake VLA at end of vbva_mouse_pointer_shape with real
+      VLA
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50010
+    - exec: don't WARN for racy path_noexec check
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50194
+    - arm64: probes: Fix uprobes for big-endian kernels
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50148
+    - Bluetooth: bnep: fix wild-memory-access in proto_unregister
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50150
+    - usb: typec: altmode should keep reference to parent
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50151
+    - smb: client: fix OOBs when building SMB2_IOCTL request
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50153
+    - scsi: target: core: Fix null-ptr-deref in target_alloc_device()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50154
+    - tcp/dccp: Don't use timer_pending() in reqsk_queue_unlink().
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50171
+    - net: systemport: fix potential memory leak in bcm_sysport_xmit()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50156
+    - drm/msm: Avoid NULL dereference in msm_disp_state_print_regs()
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50208
+    - RDMA/bnxt_re: Fix a bug while setting up Level-2 PBL pages
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50160
+    - ALSA: hda/cs8409: Fix possible NULL dereference
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50209
+    - RDMA/bnxt_re: Add a check for memory allocation
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50162
+    - bpf: devmap: provide rxq after redirect
+
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50163
+    - bpf: Make sure internal and UAPI bpf_redirect flags don't overlap
+
+  * kernel:nft "Could not process rule: Device or resource busy" on unreferenced
+    chain (LP: #2089699)
+    - SAUCE: netfilter: nf_tables: Fix EBUSY on deleting unreferenced chain
+
+  * WARN in trc_wait_for_one_reader about failed IPIs (LP: #2089373)
+    - SAUCE: rcu-tasks: fix mismerge in trc_inspect_reader
+    - rcu-tasks: Idle tasks on offline CPUs are in quiescent states
+
+  * CVE-2024-35887
+    - ax25: fix use-after-free bugs caused by ax25_ds_del_timer
+
+  * CVE-2024-40965
+    - clk: Add a devm variant of clk_rate_exclusive_get()
+    - clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()
+    - i2c: lpi2c: Avoid calling clk_get_rate during transfer
+
+  * CVE-2024-40982
+    - ssb: Fix potential NULL pointer dereference in ssb_device_uevent()
+
+  * CVE-2024-41066
+    - ibmvnic: Add tx check to prevent skb leak
+
+  * CVE-2024-42252
+    - closures: Change BUG_ON() to WARN_ON()
+
+  * CVE-2024-53097
+    - mm: krealloc: Fix MTE false alarm in __do_krealloc
+
+  * Add list of source files to linux-buildinfo (LP: #2086606)
+    - [Packaging] Sort build dependencies alphabetically
+    - [Packaging] Add list of used source files to buildinfo package
+
+  * UFS: uspi->s_3apb UBSAN: shift-out-of-bounds (LP: #2087853)
+    - ufs: ufs_sb_private_info: remove unused s_{2, 3}apb fields
+
+  * Jammy update: v5.15.169 upstream stable release (LP: #2088231)
+    - ALSA: hda/conexant - Fix audio routing for HP EliteOne 1000 G2
+    - udf: New directory iteration code
+    - udf: Convert udf_expand_dir_adinicb() to new directory iteration
+    - udf: Move udf_expand_dir_adinicb() to its callsite
+    - udf: Implement searching for directory entry using new iteration code
+    - udf: Provide function to mark entry as deleted using new directory iteration
+      code
+    - udf: Convert udf_rename() to new directory iteration code
+    - udf: Convert udf_readdir() to new directory iteration
+    - udf: Convert udf_lookup() to use new directory iteration code
+    - udf: Convert udf_get_parent() to new directory iteration code
+    - udf: Convert empty_dir() to new directory iteration code
+    - udf: Convert udf_rmdir() to new directory iteration code
+    - udf: Convert udf_unlink() to new directory iteration code
+    - udf: Implement adding of dir entries using new iteration code
+    - udf: Convert udf_add_nondir() to new directory iteration
+    - udf: Convert udf_mkdir() to new directory iteration code
+    - udf: Convert udf_link() to new directory iteration code
+    - udf: Remove old directory iteration code
+    - udf: Handle error when expanding directory
+    - udf: Don't return bh from udf_expand_dir_adinicb()
+    - udf: Fix bogus checksum computation in udf_rename()
+    - net: enetc: remove xdp_drops statistic from enetc_xdp_drop()
+    - net: enetc: add missing static descriptor and inline keyword
+    - posix-clock: Fix missing timespec64 check in pc_clock_settime()
+    - arm64: probes: Remove broken LDR (literal) uprobe support
+    - arm64: probes: Fix simulate_ldr*_literal()
+    - net: macb: Avoid 20s boot delay by skipping MDIO bus registration for fixed-
+      link PHY
+    - irqchip/gic-v3-its: Fix VSYNC referencing an unmapped VPE on GIC v4.1
+    - fat: fix uninitialized variable
+    - mm/swapfile: skip HugeTLB pages for unuse_vma
+    - secretmem: disable memfd_secret() if arch cannot set direct map
+    - dm-crypt, dm-verity: disable tasklets
+    - KVM: Fix a data race on last_boosted_vcpu in kvm_vcpu_on_spin()
+    - drm/shmem-helper: Fix BUG_ON() on mmap(PROT_WRITE, MAP_PRIVATE)
+    - io_uring/sqpoll: do not allow pinning outside of cpuset
+    - io_uring/sqpoll: retain test for whether the CPU is valid
+    - io_uring/sqpoll: do not put cpumask on stack
+    - iommu/vt-d: Fix incorrect pci_for_each_dma_alias() for non-PCI devices
+    - s390/sclp_vt220: Convert newlines to CRLF instead of LFCR
+    - KVM: s390: Change virtual to physical address access in diag 0x258 handler
+    - x86/cpufeatures: Define X86_FEATURE_AMD_IBPB_RET
+    - x86/cpufeatures: Add a IBPB_NO_RET BUG flag
+    - x86/entry: Have entry_ibpb() invalidate return predictions
+    - x86/bugs: Skip RSB fill at VMEXIT
+    - x86/bugs: Do not use UNTRAIN_RET with IBPB on entry
+    - blk-rq-qos: fix crash on rq_qos_wait vs. rq_qos_wake_function race
+    - io_uring/sqpoll: close race on waiting for sqring entries
+    - drm/radeon: Fix encoder->possible_clones
+    - drm/vmwgfx: Handle surface check failure correctly
+    - iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
+    - iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
+    - iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
+    - iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - iio: hid-sensors: Fix an error handling path in
+      _hid_sensor_set_report_latency()
+    - iio: light: veml6030: fix ALS sensor resolution
+    - iio: light: veml6030: fix IIO device retrieval from embedded device
+    - iio: light: opt3001: add missing full-scale range value
+    - iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - iio: adc: ti-ads124s08: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - Bluetooth: Remove debugfs directory on module init failure
+    - Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001
+    - xhci: Fix incorrect stream context type macro
+    - xhci: Mitigate failed set dequeue pointer commands
+    - USB: serial: option: add support for Quectel EG916Q-GL
+    - USB: serial: option: add Telit FN920C04 MBIM compositions
+    - parport: Proper fix for array out-of-bounds access
+    - x86/resctrl: Annotate get_mem_config() functions as __init
+    - x86/apic: Always explicitly disarm TSC-deadline timer
+    - x86/entry_32: Do not clobber user EFLAGS.ZF
+    - x86/entry_32: Clear CPU buffers after register restore in NMI return
+    - pinctrl: ocelot: fix system hang on level based interrupts
+    - irqchip/gic-v4: Don't allow a VMOVP on a dying VPE
+    - mptcp: track and update contiguous data status
+    - mptcp: handle consistently DSS corruption
+    - tcp: fix mptcp DSS corruption due to large pmtu xmit
+    - mptcp: fallback when MPTCP opts are dropped after 1st data
+    - mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow
+    - mptcp: prevent MPC handshake on port-based signal endpoints
+    - nilfs2: propagate directory read errors from nilfs_find_entry()
+    - powerpc/mm: Always update max/min_low_pfn in mem_topology_setup()
+    - ALSA: hda/conexant - Use cached pin control for Node 0x1d on HP EliteOne
+      1000 G2
+    - Linux 5.15.169
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 15 Jan 2025 15:52:39 +0100
+
+linux (5.15.0-131.141) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-131.141 -proposed tracker (LP: #2093573)
+
+  * CVE-2024-53164
+    - net: sched: fix ordering of qlen adjustment
+
+  * CVE-2024-53141
+    - netfilter: ipset: add missing range check in bitmap_ip_uadt
+
+  * CVE-2024-53103
+    - hv_sock: Initializing vsk->trans to NULL to prevent a dangling pointer
+
+ -- Manuel Diewald <manuel.diewald@canonical.com>  Fri, 10 Jan 2025 18:45:15 +0100
+
+linux (5.15.0-130.140) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-130.140 -proposed tracker (LP: #2092132)
+
+  * ovs/linuxbridge jobs running on ubuntu jammy broken with latest kernel
+    5.15.0-127.137 (LP: #2091990)
+    - netfilter: xtables: fix typo causing some targets not to load on IPv6
+
+ -- Mehmet Basaran <mehmet.basaran@canonical.com>  Wed, 18 Dec 2024 20:19:08 +0300
+
+linux (5.15.0-128.138) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-128.138 -proposed tracker (LP: #2090163)
+
+  * CVE-2024-50264
+    - vsock/virtio: Initialization of the dangling pointer occurring in vsk->trans
+
+  * CVE-2024-53057
+    - net/sched: stop qdisc_tree_reduce_backlog on TC_H_ROOT
+
+  * CVE-2024-43904
+    - drm/amd/display: Add null checks for 'stream' and 'plane' before
+      dereferencing
+
+  * CVE-2024-40973
+    - media: mtk-vcodec: potential null pointer deference in SCP
+
+  * CVE-2024-38553
+    - net: fec: remove .ndo_poll_controller to avoid deadlocks
+
+  * CVE-2024-26822
+    - smb: client: set correct id, uid and cruid for multiuser automounts
+
+  * CVE-2020-12351 // CVE-2020-12352 // CVE-2020-24490
+    - [Config] Disable BlueZ highspeed support
+
+  * CVE-2024-40910
+    - ax25: Fix refcount imbalance on inbound connections
+
+  * CVE-2024-35963
+    - Bluetooth: hci_sock: Fix not validating setsockopt user input
+
+  * CVE-2024-35965
+    - Bluetooth: L2CAP: Fix not validating setsockopt user input
+
+  * CVE-2024-35966
+    - Bluetooth: RFCOMM: Fix not validating setsockopt user input
+
+  * CVE-2024-35967
+    - Bluetooth: SCO: Fix not validating setsockopt user input
+
+ -- Manuel Diewald <manuel.diewald@canonical.com>  Sat, 30 Nov 2024 19:12:45 +0100
+
+linux (5.15.0-127.137) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-127.137 -proposed tracker (LP: #2086357)
+
+  * Jammy update: v5.15.168 upstream stable release (LP: #2086242)
+    - parisc: Fix 64-bit userspace syscall path
+    - parisc: Fix stack start for ADDR_NO_RANDOMIZE personality
+    - of/irq: Support #msi-cells=<0> in of_msi_get_domain
+    - drm: omapdrm: Add missing check for alloc_ordered_workqueue
+    - jbd2: stop waiting for space when jbd2_cleanup_journal_tail() returns error
+    - jbd2: correctly compare tids with tid_geq function in jbd2_fc_begin_commit
+    - mm: krealloc: consider spare memory for __GFP_ZERO
+    - ocfs2: fix the la space leak when unmounting an ocfs2 volume
+    - ocfs2: fix uninit-value in ocfs2_get_block()
+    - ocfs2: reserve space for inline xattr before attaching reflink tree
+    - ocfs2: cancel dqi_sync_work before freeing oinfo
+    - ocfs2: remove unreasonable unlock in ocfs2_read_blocks
+    - ocfs2: fix null-ptr-deref when journal load failed.
+    - ocfs2: fix possible null-ptr-deref in ocfs2_set_buffer_uptodate
+    - usbnet: ipheth: fix carrier detection in modes 1 and 4
+    - net: ethernet: use ip_hdrlen() instead of bit shift
+    - net: phy: vitesse: repair vsc73xx autonegotiation
+    - powerpc/mm: Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL
+    - btrfs: update target inode's ctime on unlink
+    - Input: ads7846 - ratelimit the spi_sync error message
+    - Input: synaptics - enable SMBus for HP Elitebook 840 G2
+    - HID: multitouch: Add support for GT7868Q
+    - scripts: kconfig: merge_config: config files: add a trailing newline
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Go 3
+    - drm/msm/adreno: Fix error return if missing firmware-name
+    - Input: i8042 - add Fujitsu Lifebook E756 to i8042 quirk table
+    - NFSv4: Fix clearing of layout segments in layoutreturn
+    - NFS: Avoid unnecessary rescanning of the per-server delegation list
+    - platform/x86: panasonic-laptop: Fix SINF array out of bounds accesses
+    - platform/x86: panasonic-laptop: Allocate 1 entry extra in the sinf array
+    - mptcp: pm: Fix uaf in __timer_delete_sync
+    - arm64: dts: rockchip: override BIOS_DISABLE signal via GPIO hog on RK3399
+      Puma
+    - minmax: reduce min/max macro expansion in atomisp driver
+    - net: tighten bad gso csum offset check in virtio_net_hdr
+    - mm: avoid leaving partial pfn mappings around in error case
+    - fs/ntfs3: Use kvfree to free memory allocated by kvmalloc
+    - arm64: dts: rockchip: fix PMIC interrupt pin in pinctrl for ROCK Pi E
+    - eeprom: digsy_mtc: Fix 93xx46 driver probe failure
+    - selftests/bpf: Support SOCK_STREAM in unix_inet_redir_to_connected()
+    - hwmon: (pmbus) Introduce and use write_byte_data callback
+    - hwmon: (pmbus) Conditionally clear individual status bits for pmbus rev >=
+      1.2
+    - ice: fix accounting for filters shared by multiple VSIs
+    - igb: Always call igb_xdp_ring_update_tail() under Tx lock
+    - net/mlx5e: Add missing link modes to ptys2ethtool_map
+    - net/mlx5: Explicitly set scheduling element and TSAR type
+    - net/mlx5: Add support to create match definer
+    - net/mlx5: Add IFC bits and enums for flow meter
+    - net/mlx5: Add missing masks and QoS bit masks for scheduling elements
+    - fou: fix initialization of grc
+    - octeontx2-af: Set XOFF on other child transmit schedulers during SMQ flush
+    - octeontx2-af: Modify SMQ flush sequence to drop packets
+    - net: ftgmac100: Enable TX interrupt to avoid TX timeout
+    - netfilter: nft_socket: fix sk refcount leaks
+    - net: dpaa: Pad packets to ETH_ZLEN
+    - spi: nxp-fspi: fix the KASAN report out-of-bounds bug
+    - dma-buf: heaps: Fix off-by-one in CMA heap fault handler
+    - ASoC: meson: axg-card: fix 'use-after-free'
+    - ASoC: allow module autoloading for table db1200_pids
+    - ALSA: hda/realtek - Fixed ALC256 headphone no sound
+    - ALSA: hda/realtek - FIxed ALC285 headphone no sound
+    - scsi: lpfc: Fix overflow build issue
+    - pinctrl: at91: make it work with current gpiolib
+    - microblaze: don't treat zero reserved memory regions as error
+    - net: ftgmac100: Ensure tx descriptor updates are visible
+    - wifi: iwlwifi: lower message level for FW buffer destination
+    - wifi: iwlwifi: mvm: fix iwl_mvm_scan_fits() calculation
+    - wifi: iwlwifi: mvm: pause TCM when the firmware is stopped
+    - wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead
+    - wifi: iwlwifi: clear trans->state earlier upon error
+    - ASoC: intel: fix module autoloading
+    - ASoC: tda7419: fix module autoloading
+    - spi: spidev: Add an entry for elgin,jg10309-01
+    - drm: komeda: Fix an issue related to normalized zpos
+    - spi: bcm63xx: Enable module autoloading
+    - x86/hyperv: Set X86_FEATURE_TSC_KNOWN_FREQ when Hyper-V provides frequency
+    - spi: spidev: Add missing spi_device_id for jg10309-01
+    - ocfs2: add bounds checking to ocfs2_xattr_find_entry()
+    - ocfs2: strict bound check before memcmp in ocfs2_xattr_find_entry()
+    - cgroup: Make operations on the cgroup root_list RCU safe
+    - Revert "wifi: cfg80211: check wiphy mutex is held for wdev mutex"
+    - gpio: prevent potential speculation leaks in gpio_device_get_desc()
+    - gpiolib: cdev: Ignore reconfiguration without direction
+    - cgroup: Move rcu_head up near the top of cgroup_root
+    - USB: serial: pl2303: add device id for Macrosilicon MS3020
+    - USB: usbtmc: prevent kernel-usb-infoleak
+    - EDAC/synopsys: Add support for version 3 of the Synopsys EDAC DDR
+    - EDAC/synopsys: Use the correct register to disable the error interrupt on v3
+      hw
+    - EDAC/synopsys: Re-enable the error interrupts on v3 hw
+    - EDAC/synopsys: Fix ECC status and IRQ control race condition
+    - EDAC/synopsys: Fix error injection on Zynq UltraScale+
+    - wifi: rtw88: always wait for both firmware loading attempts
+    - crypto: xor - fix template benchmarking
+    - ACPI: PMIC: Remove unneeded check in tps68470_pmic_opregion_probe()
+    - wifi: ath9k: fix parameter check in ath9k_init_debug()
+    - wifi: ath9k: Remove error checks when creating debugfs entries
+    - net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
+    - wifi: rtw88: remove CPT execution branch never used
+    - fs: explicitly unregister per-superblock BDIs
+    - mount: warn only once about timestamp range expiration
+    - fs/namespace: fnic: Switch to use %ptTd
+    - mount: handle OOM on mnt_warn_timestamp_expiry
+    - wifi: iwlwifi: mvm: increase the time between ranging measurements
+    - padata: Honor the caller's alignment in case of chunk_size 0
+    - can: j1939: use correct function name in comment
+    - ACPI: CPPC: Fix MASK_VAL() usage
+    - netfilter: nf_tables: elements with timeout below CONFIG_HZ never expire
+    - netfilter: nf_tables: reject element expiration with no timeout
+    - netfilter: nf_tables: reject expiration higher than timeout
+    - netfilter: nf_tables: remove annotation to access set timeout while holding
+      lock
+    - cpufreq: ti-cpufreq: Introduce quirks to handle syscon fails appropriately
+    - x86/sgx: Fix deadlock in SGX NUMA node search
+    - wifi: cfg80211: fix UBSAN noise in cfg80211_wext_siwscan()
+    - wifi: mt76: mt7915: fix rx filter setting for bfee functionality
+    - wifi: cfg80211: fix two more possible UBSAN-detected off-by-one errors
+    - wifi: mac80211: use two-phase skb reclamation in ieee80211_do_stop()
+    - wifi: wilc1000: fix potential RCU dereference issue in
+      wilc_parse_join_bss_param
+    - sock_map: Add a cond_resched() in sock_hash_free()
+    - can: bcm: Clear bo->bcm_proc_read after remove_proc_entry().
+    - can: m_can: m_can_close(): stop clocks after device has been shut down
+    - Bluetooth: btusb: Fix not handling ZPL/short-transfer
+    - bareudp: Pull inner IP header in bareudp_udp_encap_recv().
+    - net: geneve: support IPv4/IPv6 as inner protocol
+    - geneve: Fix incorrect inner network header offset when innerprotoinherit is
+      set
+    - bareudp: Pull inner IP header on xmit.
+    - net: enetc: Use IRQF_NO_AUTOEN flag in request_irq()
+    - r8169: disable ALDPS per default for RTL8125
+    - net: ipv6: rpl_iptunnel: Fix memory leak in rpl_input
+    - net: tipc: avoid possible garbage value
+    - block, bfq: fix possible UAF for bfqq->bic with merge chain
+    - block, bfq: choose the last bfqq from merge chain in bfq_setup_cooperator()
+    - block, bfq: don't break merge chain in bfq_split_bfqq()
+    - block: print symbolic error name instead of error code
+    - block: fix potential invalid pointer dereference in blk_add_partition
+    - spi: ppc4xx: handle irq_of_parse_and_map() errors
+    - spi: ppc4xx: Avoid returning 0 when failed to parse and map IRQ
+    - arm64: dts: renesas: r9a07g044: Correct GICD and GICR sizes
+    - ARM: dts: microchip: sam9x60: Fix rtc/rtt clocks
+    - ARM: dts: imx7d-zii-rmu2: fix Ethernet PHY pinctrl property
+    - ARM: versatile: fix OF node leak in CPUs prepare
+    - reset: berlin: fix OF node leak in probe() error path
+    - reset: k210: fix OF node leak in probe() error path
+    - clocksource/drivers/qcom: Add missing iounmap() on errors in
+      msm_dt_timer_init()
+    - m68k: Fix kernel_clone_args.flags in m68k_clone()
+    - hwmon: (max16065) Fix overflows seen when writing limits
+    - i2c: Add i2c_get_match_data()
+    - hwmon: (max16065) Remove use of i2c_match_id()
+    - hwmon: (max16065) Fix alarm attributes
+    - mtd: slram: insert break after errors in parsing the map
+    - hwmon: (ntc_thermistor) fix module autoloading
+    - power: supply: axp20x_battery: Remove design from min and max voltage
+    - power: supply: max17042_battery: Fix SOC threshold calc w/ no current sense
+    - fbdev: hpfb: Fix an error handling path in hpfb_dio_probe()
+    - mtd: powernv: Add check devm_kasprintf() returned value
+    - pmdomain: core: Harden inter-column space in debug summary
+    - drm/stm: Fix an error handling path in stm_drm_platform_probe()
+    - drm/amd/display: Add null check for set_output_gamma in
+      dcn30_set_output_transfer_func
+    - drm/amdgpu: Replace one-element array with flexible-array member
+    - drm/amdgpu: properly handle vbios fake edid sizing
+    - drm/radeon: Replace one-element array with flexible-array member
+    - drm/radeon: properly handle vbios fake edid sizing
+    - scsi: NCR5380: Add SCp members to struct NCR5380_cmd
+    - scsi: NCR5380: Check for phase match during PDMA fixup
+    - drm/rockchip: vop: Allow 4096px width scaling
+    - drm/rockchip: dw_hdmi: Fix reading EDID when using a forced mode
+    - drm/radeon/evergreen_cs: fix int overflow errors in cs track offsets
+    - drm/bridge: lontium-lt8912b: Validate mode in drm_bridge_funcs::mode_valid()
+    - scsi: elx: libefc: Fix potential use after free in efc_nport_vport_del()
+    - jfs: fix out-of-bounds in dbNextAG() and diAlloc()
+    - drm/mediatek: Use spin_lock_irqsave() for CRTC event lock
+    - powerpc/32: Remove the 'nobats' kernel parameter
+    - powerpc/32: Remove 'noltlbs' kernel parameter
+    - powerpc/8xx: Fix initial memory mapping
+    - powerpc/8xx: Fix kernel vs user address comparison
+    - drm/msm: Fix incorrect file name output in adreno_request_fw()
+    - drm/msm/a5xx: disable preemption in submits by default
+    - drm/msm/a5xx: properly clear preemption records on resume
+    - drm/msm/a5xx: fix races in preemption evaluation stage
+    - drm/msm: Drop priv->lastctx
+    - drm/msm/a5xx: workaround early ring-buffer emptiness check
+    - ipmi: docs: don't advertise deprecated sysfs entries
+    - drm/msm: fix %s null argument error
+    - drivers:drm:exynos_drm_gsc:Fix wrong assignment in gsc_bind()
+    - xen: use correct end address of kernel for conflict checking
+    - xen/swiotlb: add alignment check for dma buffers
+    - tpm: Clean up TPM space after command failure
+    - selftests/bpf: Fix compile error from rlim_t in sk_storage_map.c
+    - selftests/bpf: Fix error compiling bpf_iter_setsockopt.c with musl libc
+    - selftests/bpf: Fix missing ARRAY_SIZE() definition in bench.c
+    - selftests/bpf: Fix compiling kfree_skb.c with musl-libc
+    - selftests/bpf: Fix compiling flow_dissector.c with musl-libc
+    - selftests/bpf: Fix compiling tcp_rtt.c with musl-libc
+    - selftests/bpf: Fix compiling core_reloc.c with musl-libc
+    - selftests/bpf: Fix errors compiling cg_storage_multi.h with musl libc
+    - selftests/bpf: Fix error compiling test_lru_map.c
+    - selftests/bpf: Fix C++ compile error from missing _Bool type
+    - xz: cleanup CRC32 edits from 2018
+    - kthread: fix task state in kthread worker if being frozen
+    - ext4: clear EXT4_GROUP_INFO_WAS_TRIMMED_BIT even mount with discard
+    - smackfs: Use rcu_assign_pointer() to ensure safe assignment in smk_set_cipso
+    - ext4: avoid buffer_head leak in ext4_mark_inode_used()
+    - ext4: avoid potential buffer_head leak in __ext4_new_inode()
+    - ext4: avoid negative min_clusters in find_group_orlov()
+    - ext4: return error on ext4_find_inline_entry
+    - ext4: avoid OOB when system.data xattr changes underneath the filesystem
+    - nilfs2: fix potential null-ptr-deref in nilfs_btree_insert()
+    - nilfs2: determine empty node blocks as corrupted
+    - nilfs2: fix potential oob read in nilfs_btree_check_delete()
+    - bpf: Fix bpf_strtol and bpf_strtoul helpers for 32bit
+    - perf mem: Free the allocated sort string, fixing a leak
+    - perf sched timehist: Fix missing free of session in perf_sched__timehist()
+    - perf sched timehist: Fixed timestamp error when unable to confirm event
+      sched_in time
+    - perf time-utils: Fix 32-bit nsec parsing
+    - clk: imx: imx8mp: fix clock tree update of TF-A managed clocks
+    - clk: imx: imx8qxp: Register dc0_bypass0_clk before disp clk
+    - clk: imx: imx8qxp: Parent should be initialized earlier than the clock
+    - remoteproc: imx_rproc: Correct ddr alias for i.MX8M
+    - remoteproc: imx_rproc: Initialize workqueue earlier
+    - clk: rockchip: Set parent rate for DCLK_VOP clock on RK3228
+    - Input: ilitek_ts_i2c - avoid wrong input subsystem sync
+    - Input: ilitek_ts_i2c - add report id message validation
+    - drivers: media: dvb-frontends/rtl2832: fix an out-of-bounds write error
+    - drivers: media: dvb-frontends/rtl2830: fix an out-of-bounds write error
+    - PCI: keystone: Fix if-statement expression in ks_pcie_quirk()
+    - PCI: xilinx-nwl: Fix register misspelling
+    - PCI: xilinx-nwl: Clean up clock on probe failure/removal
+    - RDMA/iwcm: Fix WARNING:at_kernel/workqueue.c:#check_flush_dependency
+    - pinctrl: single: fix missing error code in pcs_probe()
+    - RDMA/rtrs: Reset hb_missed_cnt after receiving other traffic from peer
+    - RDMA/rtrs-clt: Reset cid to con_num - 1 to stay in bounds
+    - clk: ti: dra7-atl: Fix leak of of_nodes
+    - nfsd: remove unneeded EEXIST error check in nfsd_do_file_acquire
+    - nfsd: fix refcount leak when file is unhashed after being found
+    - pinctrl: mvebu: Use devm_platform_get_and_ioremap_resource()
+    - pinctrl: mvebu: Fix devinit_dove_pinctrl_probe function
+    - IB/core: Fix ib_cache_setup_one error flow cleanup
+    - watchdog: imx_sc_wdt: Don't disable WDT in suspend
+    - RDMA/hns: Don't modify rq next block addr in HIP09 QPC
+    - RDMA/hns: Fix the overflow risk of hem_list_calc_ba_range()
+    - RDMA/hns: Fix spin_unlock_irqrestore() called with IRQs enabled
+    - RDMA/hns: Remove unused abnormal interrupt of type RAS
+    - RDMA/hns: Fix the wrong type of return value of the interrupt handler
+    - RDMA/hns: Refactor the abnormal interrupt handler function
+    - RDMA/hns: Fix VF triggering PF reset in abnormal interrupt handler
+    - RDMA/hns: Optimize hem allocation performance
+    - riscv: Fix fp alignment bug in perf_callchain_user()
+    - RDMA/cxgb4: Added NULL check for lookup_atid
+    - RDMA/irdma: fix error message in irdma_modify_qp_roce()
+    - ntb: intel: Fix the NULL vs IS_ERR() bug for debugfs_create_dir()
+    - ntb_perf: Fix printk format
+    - nfsd: call cache_put if xdr_reserve_space returns NULL
+    - nfsd: return -EINVAL when namelen is 0
+    - f2fs: fix typo
+    - f2fs: fix to update i_ctime in __f2fs_setxattr()
+    - f2fs: remove unneeded check condition in __f2fs_setxattr()
+    - f2fs: reduce expensive checkpoint trigger frequency
+    - f2fs: optimize error handling in redirty_blocks
+    - f2fs: fix to wait page writeback before setting gcing flag
+    - f2fs: introduce F2FS_IPU_HONOR_OPU_WRITE ipu policy
+    - f2fs: clean up w/ dotdot_name
+    - f2fs: get rid of online repaire on corrupted directory
+    - spi: lpspi: Silence error message upon deferred probe
+    - spi: lpspi: release requested DMA channels
+    - spi: spi-fsl-lpspi: Undo runtime PM changes at driver exit time
+    - iio: adc: ad7606: fix oversampling gpio array
+    - iio: adc: ad7606: fix standby gpio state to match the documentation
+    - coresight: tmc: sg: Do not leak sg_table
+    - interconnect: qcom: sm8250: Enable sync_state
+    - vdpa: Add eventfd for the vdpa callback
+    - vhost_vdpa: assign irq bypass producer token correctly
+    - Revert "dm: requeue IO if mapping table not yet available"
+    - net: axienet: Clean up device used for DMA calls
+    - net: axienet: Clean up DMA start/stop and error handling
+    - net: axienet: don't set IRQ timer when IRQ delay not used
+    - net: axienet: implement NAPI and GRO receive
+    - net: axienet: reduce default RX interrupt threshold to 1
+    - net: axienet: add coalesce timer ethtool configuration
+    - net: axienet: Be more careful about updating tx_bd_tail
+    - net: axienet: Use NAPI for TX completion path
+    - net: axienet: Switch to 64-bit RX/TX statistics
+    - net: xilinx: axienet: Fix packet counting
+    - netfilter: nf_reject_ipv6: fix nf_reject_ip6_tcphdr_put()
+    - net: seeq: Fix use after free vulnerability in ether3 Driver Due to Race
+      Condition
+    - net: ipv6: select DST_CACHE from IPV6_RPL_LWTUNNEL
+    - tcp: check skb is non-NULL in tcp_rto_delta_us()
+    - net: qrtr: Update packets cloning when broadcasting
+    - bonding: Fix unnecessary warnings and logs from bond_xdp_get_xmit_slave()
+    - netfilter: nf_tables: Keep deleted flowtable hooks until after RCU
+    - netfilter: ctnetlink: compile ctnetlink_label_size with
+      CONFIG_NF_CONNTRACK_EVENTS
+    - drm/amd/display: Fix Synaptics Cascaded Panamera DSC Determination
+    - Input: goodix - use the new soc_intel_is_byt() helper
+    - powercap: RAPL: fix invalid initialization for pl4_supported field
+    - x86/mm: Switch to new Intel CPU model defines
+    - vfio/pci: fix potential memory leak in vfio_intx_enable()
+    - selinux,smack: don't bypass permissions check in inode_setsecctx hook
+    - Remove *.orig pattern from .gitignore
+    - PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
+    - ASoC: rt5682: Return devm_of_clk_add_hw_provider to transfer the error
+    - soc: versatile: integrator: fix OF node leak in probe() error path
+    - Revert "media: tuners: fix error return code of
+      hybrid_tuner_request_state()"
+    - Input: i8042 - add TUXEDO Stellaris 16 Gen5 AMD to i8042 quirk table
+    - Input: i8042 - add TUXEDO Stellaris 15 Slim Gen6 AMD to i8042 quirk table
+    - Input: i8042 - add another board name for TUXEDO Stellaris Gen5 AMD line
+    - drm/amd/display: Round calculated vtotal
+    - drm/amd/display: Validate backlight caps are sane
+    - scsi: mac_scsi: Revise printk(KERN_DEBUG ...) messages
+    - scsi: mac_scsi: Refactor polling loop
+    - scsi: mac_scsi: Disallow bus errors during PDMA send
+    - usbnet: fix cyclical race on disconnect with work queue
+    - USB: appledisplay: close race between probe and completion handler
+    - USB: misc: cypress_cy7c63: check for short transfer
+    - USB: class: CDC-ACM: fix race between get_serial and set_serial
+    - usb: cdnsp: Fix incorrect usb_request status
+    - usb: dwc2: drd: fix clock gating on USB role switch
+    - bus: integrator-lm: fix OF node leak in probe()
+    - firmware_loader: Block path traversal
+    - tty: rp2: Fix reset with non forgiving PCIe host bridges
+    - xhci: Set quirky xHC PCI hosts to D3 _after_ stopping and freeing them.
+    - crypto: ccp - Properly unregister /dev/sev on sev PLATFORM_STATUS failure
+    - drbd: Fix atomicity violation in drbd_uuid_set_bm()
+    - drbd: Add NULL check for net_conf to prevent dereference in state validation
+    - ACPI: sysfs: validate return type of _STR method
+    - ACPI: resource: Add another DMI match for the TongFang GMxXGxx
+    - efistub/tpm: Use ACPI reclaim memory for event log to avoid corruption
+    - perf/x86/intel/pt: Fix sampling synchronization
+    - wifi: rtw88: 8822c: Fix reported RX band width
+    - wifi: mt76: mt7615: check devm_kasprintf() returned value
+    - debugobjects: Fix conditions in fill_pool()
+    - f2fs: prevent possible int overflow in dir_block_index()
+    - f2fs: avoid potential int overflow in sanity_check_area_boundary()
+    - hwrng: mtk - Use devm_pm_runtime_enable
+    - hwrng: bcm2835 - Add missing clk_disable_unprepare in bcm2835_rng_init
+    - hwrng: cctrng - Add missing clk_disable_unprepare in cctrng_resume
+    - arm64: dts: rockchip: Raise Pinebook Pro's panel backlight PWM frequency
+    - arm64: dts: rockchip: Correct the Pinebook Pro battery design capacity
+    - vfs: fix race between evice_inodes() and find_inode()&iput()
+    - fs: Fix file_set_fowner LSM hook inconsistencies
+    - nfs: fix memory leak in error path of nfs4_do_reclaim
+    - EDAC/igen6: Fix conversion of system address to physical memory address
+    - padata: use integer wrap around to prevent deadlock on seq_nr overflow
+    - soc: versatile: realview: fix memory leak during device remove
+    - soc: versatile: realview: fix soc_dev leak during device remove
+    - usb: yurex: Replace snprintf() with the safer scnprintf() variant
+    - USB: misc: yurex: fix race between read and write
+    - xhci: fix event ring segment table related masks and variables in header
+    - xhci: remove xhci_test_trb_in_td_math early development check
+    - xhci: Refactor interrupter code for initial multi interrupter support.
+    - xhci: Preserve RsvdP bits in ERSTBA register correctly
+    - xhci: Add a quirk for writing ERST in high-low order
+    - usb: xhci: fix loss of data on Cadence xHC
+    - pps: remove usage of the deprecated ida_simple_xx() API
+    - pps: add an error check in parport_attach
+    - x86/idtentry: Incorporate definitions/declarations of the FRED entries
+    - x86/entry: Remove unwanted instrumentation in common_interrupt()
+    - bpf: lsm: Set bpf_lsm_blob_sizes.lbs_task to 0
+    - lockdep: fix deadlock issue between lockdep and rcu
+    - mm: only enforce minimum stack gap size if it's sensible
+    - i2c: aspeed: Update the stop sw state when the bus recovery occurs
+    - i2c: isch: Add missed 'else'
+    - usb: yurex: Fix inconsistent locking bug in yurex_read()
+    - spi: lpspi: Simplify some error message
+    - static_call: Handle module init failure correctly in
+      static_call_del_module()
+    - static_call: Replace pointless WARN_ON() in static_call_module_notify()
+    - mailbox: rockchip: fix a typo in module autoloading
+    - mailbox: bcm2835: Fix timeout during suspend mode
+    - ceph: remove the incorrect Fw reference check when dirtying pages
+    - ieee802154: Fix build error
+    - net/mlx5: Fix error path in multi-packet WQE transmit
+    - net/mlx5: Added cond_resched() to crdump collection
+    - net/mlx5e: Fix NULL deref in mlx5e_tir_builder_alloc()
+    - netfilter: uapi: NFTA_FLOWTABLE_HOOK is NLA_NESTED
+    - net: ieee802154: mcr20a: Use IRQF_NO_AUTOEN flag in request_irq()
+    - netfilter: nf_tables: prevent nf_skb_duplicated corruption
+    - Bluetooth: btmrvl: Use IRQF_NO_AUTOEN flag in request_irq()
+    - net: ethernet: lantiq_etop: fix memory disclosure
+    - net: avoid potential underflow in qdisc_pkt_len_init() with UFO
+    - net: add more sanity checks to qdisc_pkt_len_init()
+    - stmmac_pci: Fix underflow size in stmmac_rx
+    - net: stmmac: Disable automatic FCS/Pad stripping
+    - net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check
+    - ipv4: ip_gre: Fix drops of small packets in ipgre_xmit
+    - ppp: do not assume bh is held in ppp_channel_bridge_input()
+    - sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
+    - i2c: xiic: Fix broken locking on tx_msg
+    - i2c: xiic: Switch from waitqueue to completion
+    - i2c: xiic: Fix RX IRQ busy check
+    - i2c: xiic: xiic_xfer(): Fix runtime PM leak on error path
+    - i2c: xiic: improve error message when transfer fails to start
+    - i2c: xiic: Try re-initialization on bus busy timeout
+    - media: usbtv: Remove useless locks in usbtv_video_free()
+    - ALSA: mixer_oss: Remove some incorrect kfree_const() usages
+    - ALSA: hda/realtek: Fix the push button function for the ALC257
+    - ALSA: hda/generic: Unconditionally prefer preferred_dacs pairs
+    - ASoC: imx-card: Set card.owner to avoid a warning calltrace if SND=m
+    - ALSA: hda/conexant: Fix conflicting quirk for System76 Pangolin
+    - f2fs: Require FMODE_WRITE for atomic write ioctls
+    - wifi: ath9k: fix possible integer overflow in ath9k_get_et_stats()
+    - wifi: ath9k_htc: Use __skb_set_length() for resetting urb before resubmit
+    - ice: Adjust over allocation of memory in ice_sched_add_root_node() and
+      ice_sched_add_node()
+    - net/xen-netback: prevent UAF in xenvif_flush_hash()
+    - net: hisilicon: hip04: fix OF node leak in probe()
+    - net: hisilicon: hns_dsaf_mac: fix OF node leak in hns_mac_get_info()
+    - net: hisilicon: hns_mdio: fix OF node leak in probe()
+    - ACPI: PAD: fix crash in exit_round_robin()
+    - ACPICA: Fix memory leak if acpi_ps_get_next_namepath() fails
+    - ACPICA: Fix memory leak if acpi_ps_get_next_field() fails
+    - net: sched: consistently use rcu_replace_pointer() in taprio_change()
+    - blk_iocost: fix more out of bound shifts
+    - nvme-pci: qdepth 1 quirk
+    - wifi: ath11k: fix array out-of-bound access in SoC stats
+    - wifi: rtw88: select WANT_DEV_COREDUMP
+    - ACPI: EC: Do not release locks during operation region accesses
+    - ACPICA: check null return of ACPI_ALLOCATE_ZEROED() in
+      acpi_db_convert_to_package()
+    - tipc: guard against string buffer overrun
+    - net: mvpp2: Increase size of queue_name buffer
+    - ipv4: Check !in_dev earlier for ioctl(SIOCSIFADDR).
+    - ipv4: Mask upper DSCP bits and ECN bits in NETLINK_FIB_LOOKUP family
+    - net: atlantic: Avoid warning about potential string truncation
+    - tcp: avoid reusing FIN_WAIT2 when trying to find port in connect() process
+    - ACPICA: iasl: handle empty connection_node
+    - proc: add config & param to block forcing mem writes
+    - [Config] updateconfigs to select PROC_MEM_ALWAYS_FORCE
+    - wifi: mt76: mt7915: hold dev->mt76.mutex while disabling tx worker
+    - wifi: mwifiex: Fix memcpy() field-spanning write warning in
+      mwifiex_cmd_802_11_scan_ext()
+    - nfp: Use IRQF_NO_AUTOEN flag in request_irq()
+    - signal: Replace BUG_ON()s
+    - ALSA: usb-audio: Add input value sanity checks for standard types
+    - x86/ioapic: Handle allocation failures gracefully
+    - ALSA: usb-audio: Define macros for quirk table entries
+    - ALSA: usb-audio: Add logitech Audio profile quirk
+    - tools/x86/kcpuid: Protect against faulty "max subleaf" values
+    - ALSA: asihpi: Fix potential OOB array access
+    - ALSA: hdsp: Break infinite MIDI input flush loop
+    - x86/syscall: Avoid memcpy() for ia32 syscall_get_arguments()
+    - fbdev: pxafb: Fix possible use after free in pxafb_task()
+    - rcuscale: Provide clear error when async specified without primitives
+    - iommu/arm-smmu-qcom: hide last LPASS SMMU context bank from linux
+    - power: reset: brcmstb: Do not go into infinite loop if reset fails
+    - iommu/vt-d: Always reserve a domain ID for identity setup
+    - iommu/vt-d: Fix potential lockup if qi_submit_sync called with 0 count
+    - drm/amd/display: Add null check for top_pipe_to_program in
+      commit_planes_for_stream
+    - ata: sata_sil: Rename sil_blacklist to sil_quirks
+    - drm/amd/display: Check null pointers before using dc->clk_mgr
+    - jfs: UBSAN: shift-out-of-bounds in dbFindBits
+    - jfs: Fix uaf in dbFreeBits
+    - jfs: check if leafidx greater than num leaves per dmap tree
+    - scsi: smartpqi: correct stream detection
+    - jfs: Fix uninit-value access of new_ea in ea_buffer
+    - drm/amdgpu: add raven1 gfxoff quirk
+    - drm/amdgpu: enable gfxoff quirk on HP 705G4
+    - HID: multitouch: Add support for Thinkpad X12 Gen 2 Kbd Portfolio
+    - platform/x86: touchscreen_dmi: add nanote-next quirk
+    - drm/amd/display: Check stream before comparing them
+    - drm/amd/display: Fix index out of bounds in DCN30 degamma hardware format
+      translation
+    - drm/amd/display: Fix index out of bounds in degamma hardware format
+      translation
+    - drm/amd/display: Fix index out of bounds in DCN30 color transformation
+    - drm/amd/display: Initialize get_bytes_per_element's default to 1
+    - drm/printer: Allow NULL data in devcoredump printer
+    - scsi: aacraid: Rearrange order of struct aac_srb_unit
+    - drm/radeon/r100: Handle unknown family in r100_cp_init_microcode()
+    - drm/amd/pm: ensure the fw_info is not null before using it
+    - of/irq: Refer to actual buffer size in of_irq_parse_one()
+    - ext4: ext4_search_dir should return a proper error
+    - ext4: avoid use-after-free in ext4_ext_show_leaf()
+    - ext4: fix i_data_sem unlock order in ext4_ind_migrate()
+    - blk-integrity: use sysfs_emit
+    - blk-integrity: convert to struct device_attribute
+    - blk-integrity: register sysfs attributes on struct device
+    - usb: typec: tcpm: Check for port partner validity before consuming it
+    - spi: spi-imx: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - spi: s3c64xx: fix timeout counters in flush_fifo
+    - selftests: breakpoints: use remaining time to check if suspend succeed
+    - selftests: vDSO: fix vDSO name for powerpc
+    - selftests: vDSO: fix vdso_config for powerpc
+    - selftests: vDSO: fix vDSO symbols lookup for powerpc64
+    - selftests/mm: fix charge_reserved_hugetlb.sh test
+    - selftests: vDSO: fix ELF hash table entry size for s390x
+    - selftests: vDSO: fix vdso_config for s390
+    - platform/x86: ISST: Fix the KASAN report slab-out-of-bounds bug
+    - i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume
+    - i2c: qcom-geni: Use IRQF_NO_AUTOEN flag in request_irq()
+    - i2c: xiic: Wait for TX empty to avoid missed TX NAKs
+    - firmware: tegra: bpmp: Drop unused mbox_client_to_bpmp()
+    - spi: bcm63xx: Fix module autoloading
+    - power: supply: hwmon: Fix missing temp1_max_alarm attribute
+    - perf/core: Fix small negative period being ignored
+    - parisc: Fix itlb miss handler for 64-bit programs
+    - drm: Consistently use struct drm_mode_rect for FB_DAMAGE_CLIPS
+    - ALSA: core: add isascii() check to card ID generator
+    - ALSA: usb-audio: Add delay quirk for VIVO USB-C HEADSET
+    - ALSA: usb-audio: Add native DSD support for Luxman D-08u
+    - ALSA: line6: add hw monitor volume control to POD HD500X
+    - ALSA: hda/realtek: Add quirk for Huawei MateBook 13 KLV-WX9
+    - ext4: no need to continue when the number of entries is 1
+    - ext4: correct encrypted dentry name hash when not casefolded
+    - ext4: fix slab-use-after-free in ext4_split_extent_at()
+    - ext4: propagate errors from ext4_find_extent() in ext4_insert_range()
+    - ext4: fix incorrect tid assumption in __jbd2_log_wait_for_space()
+    - ext4: drop ppath from ext4_ext_replay_update_ex() to avoid double-free
+    - ext4: aovid use-after-free in ext4_ext_insert_extent()
+    - ext4: fix double brelse() the buffer of the extents path
+    - ext4: update orig_path in ext4_find_extent()
+    - ext4: fix incorrect tid assumption in ext4_wait_for_tail_page_commit()
+    - ext4: fix incorrect tid assumption in jbd2_journal_shrink_checkpoint_list()
+    - ext4: fix fast commit inode enqueueing during a full journal commit
+    - ext4: use handle to mark fc as ineligible in __track_dentry_update()
+    - ext4: mark fc as ineligible using an handle in ext4_xattr_set()
+    - riscv: define ILLEGAL_POINTER_VALUE for 64bit
+    - exfat: fix memory leak in exfat_load_bitmap()
+    - perf hist: Update hist symbol when updating maps
+    - nfsd: fix delegation_blocked() to block correctly for at least 30 seconds
+    - nfsd: map the EBADMSG to nfserr_io to avoid warning
+    - NFSD: Fix NFSv4's PUTPUBFH operation
+    - aoe: fix the potential use-after-free problem in more places
+    - clk: rockchip: fix error for unknown clocks
+    - clk: qcom: dispcc-sm8250: use CLK_SET_RATE_PARENT for branch clocks
+    - media: sun4i_csi: Implement link validate for sun4i_csi subdev
+    - media: uapi/linux/cec.h: cec_msg_set_reply_to: zero flags
+    - clk: qcom: clk-rpmh: Fix overflow in BCM vote
+    - clk: qcom: gcc-sm8150: De-register gcc_cpuss_ahb_clk_src
+    - media: venus: fix use after free bug in venus_remove due to race condition
+    - clk: qcom: gcc-sm8250: Do not turn off PCIe GDSCs during gdsc_disable()
+    - clk: qcom: gcc-sc8180x: Fix the sdcc2 and sdcc4 clocks freq table
+    - iio: magnetometer: ak8975: Fix reading for ak099xx sensors
+    - tomoyo: fallback to realpath if symlink's pathname does not exist
+    - net: stmmac: Fix zero-division error when disabling tc cbs
+    - rtc: at91sam9: fix OF node leak in probe() error path
+    - Input: adp5589-keys - fix NULL pointer dereference
+    - Input: adp5589-keys - fix adp5589_gpio_get_value()
+    - ACPI: resource: Add Asus Vivobook X1704VAP to irq1_level_low_skip_override[]
+    - ACPI: resource: Add Asus ExpertBook B2502CVA to
+      irq1_level_low_skip_override[]
+    - btrfs: fix a NULL pointer dereference when failed to start a new trasacntion
+    - btrfs: wait for fixup workers before stopping cleaner kthread during umount
+    - gpio: davinci: fix lazy disable
+    - tracing/hwlat: Fix a race during cpuhp processing
+    - tracing/timerlat: Fix a race during cpuhp processing
+    - close_range(): fix the logics in descriptor table trimming
+    - drm/sched: Add locking to drm_sched_entity_modify_sched
+    - drm/amd/display: Fix system hang while resume with TBT monitor
+    - kconfig: qconf: fix buffer overflow in debug links
+    - device property: Add fwnode_iomap()
+    - device property: Add fwnode_irq_get_byname
+    - i2c: smbus: Use device_*() functions instead of of_*()
+    - i2c: create debugfs entry per adapter
+    - i2c: core: Lock address during client device instantiation
+    - i2c: xiic: Use devm_clk_get_enabled()
+    - i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - spi: bcm63xx: Fix missing pm_runtime_disable()
+    - ext4: properly sync file size update after O_SYNC direct IO
+    - ext4: dax: fix overflowing extents beyond inode size when partially writing
+    - arm64: Add Cortex-715 CPU part definition
+    - arm64: cputype: Add Neoverse-N3 definitions
+    - arm64: errata: Expand speculative SSBS workaround once more
+    - uprobes: fix kernel info leak via "[uprobes]" vma
+    - drm/amd/display: Allow backlight to go below
+      `AMDGPU_DM_DEFAULT_MIN_BACKLIGHT`
+    - build-id: require program headers to be right after ELF header
+    - lib/buildid: harden build ID parsing logic
+    - drm/rockchip: define gamma registers for RK3399
+    - drm/rockchip: support gamma control on RK3399
+    - drm/rockchip: vop: clear DMA stop bit on RK3066
+    - media: i2c: imx335: Enable regulator supplies
+    - media: imx335: Fix reset-gpio handling
+    - dt-bindings: clock: qcom: Add missing UFS QREF clocks
+    - dt-bindings: clock: qcom: Add GPLL9 support on gcc-sc8180x
+    - r8169: Fix spelling mistake: "tx_underun" -> "tx_underrun"
+    - r8169: add tally counter fields added with RTL8125
+    - clk: qcom: gcc-sc8180x: Add GPLL9 support
+    - ACPI: battery: Simplify battery hook locking
+    - ACPI: battery: Fix possible crash when unregistering a battery hook
+    - Revert "arm64: dts: qcom: sm8250: switch UFS QMP PHY to new style of
+      bindings"
+    - ext4: fix inode tree inconsistency caused by ENOMEM
+    - 9p: add missing locking around taking dentry fid list
+    - vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
+    - perf report: Fix segfault when 'sym' sort key is not used
+    - ALSA: usb-audio: Fix possible NULL pointer dereference in
+      snd_usb_pcm_has_fixed_rate()
+    - unicode: Don't special case ignorable code points
+    - net: ethernet: cortina: Drop TSO support
+    - tracing: Remove precision vsnprintf() check from print event
+    - drm/crtc: fix uninitialized variable use even harder
+    - tracing: Have saved_cmdlines arrays all in one allocation
+    - selftests/net: give more time to udpgro bg processes to complete startup
+    - selftests/net: synchronize udpgro tests' tx and rx connection
+    - selftests: net: Remove executable bits from library scripts
+    - fs/ntfs3: Refactor enum_rstbl to suppress static checker
+    - virtio_console: fix misc probe bugs
+    - Input: synaptics-rmi4 - fix UAF of IRQ domain on driver removal
+    - bpf: Check percpu map value size first
+    - s390/facility: Disable compile time optimization for decompressor code
+    - s390/mm: Add cond_resched() to cmm_alloc/free_pages()
+    - bpf, x64: Fix a jit convergence issue
+    - ext4: don't set SB_RDONLY after filesystem errors
+    - ext4: nested locking for xattr inode
+    - s390/cpum_sf: Remove WARN_ON_ONCE statements
+    - ktest.pl: Avoid false positives with grub2 skip regex
+    - RDMA/mad: Improve handling of timed out WRs of mad agent
+    - PCI: Add function 0 DMA alias quirk for Glenfly Arise chip
+    - RDMA/rtrs-srv: Avoid null pointer deref during path establishment
+    - clk: bcm: bcm53573: fix OF node leak in init
+    - PCI: Add ACS quirk for Qualcomm SA8775P
+    - i2c: i801: Use a different adapter-name for IDF adapters
+    - PCI: Mark Creative Labs EMU20k2 INTx masking as broken
+    - ntb: ntb_hw_switchtec: Fix use after free vulnerability in
+      switchtec_ntb_remove due to race condition
+    - media: videobuf2-core: clear memory related fields in
+      __vb2_plane_dmabuf_put()
+    - remoteproc: imx_rproc: Use imx specific hook for find_loaded_rsc_table
+    - clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D
+    - usb: chipidea: udc: enable suspend interrupt after usb reset
+    - usb: dwc2: Adjust the timing of USB Driver Interrupt Registration in the
+      Crashkernel Scenario
+    - comedi: ni_routing: tools: Check when the file could not be opened
+    - virtio_pmem: Check device status before requesting flush
+    - tools/iio: Add memory allocation failure check for trigger_name
+    - driver core: bus: Return -EIO instead of 0 when show/store invalid bus
+      attribute
+    - drm/amd/display: Check null pointer before dereferencing se
+    - fbdev: sisfb: Fix strbuf array overflow
+    - RDMA/rxe: Fix seg fault in rxe_comp_queue_pkt
+    - NFSD: Mark filecache "down" if init fails
+    - ice: fix VLAN replay after reset
+    - SUNRPC: Fix integer overflow in decode_rc_list()
+    - NFSv4: Prevent NULL-pointer dereference in nfs42_complete_copies()
+    - net: phy: dp83869: fix memory corruption when enabling fiber
+    - tcp: fix to allow timestamp undo if no retransmits were sent
+    - tcp: fix tcp_enter_recovery() to zero retrans_stamp when it's safe
+    - netfilter: br_netfilter: fix panic with metadata_dst skb
+    - Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
+    - net: phy: bcm84881: Fix some error handling paths
+    - thermal: int340x: processor_thermal: Set feature mask before
+      proc_thermal_add
+    - thermal: intel: int340x: processor: Fix warning during module unload
+    - net: dsa: b53: fix jumbo frame mtu check
+    - net: dsa: b53: fix max MTU for 1g switches
+    - net: dsa: b53: fix max MTU for BCM5325/BCM5365
+    - net: dsa: b53: allow lower MTUs on BCM5325/5365
+    - net: dsa: b53: fix jumbo frames on 10/100 ports
+    - gpio: aspeed: Add the flush write to ensure the write complete.
+    - gpio: aspeed: Use devm_clk api to manage clock source
+    - ice: Fix netif_is_ice() in Safe Mode
+    - i40e: Fix macvlan leak by synchronizing access to mac_filter_hash
+    - igb: Do not bring the device up after non-fatal error
+    - net/sched: accept TCA_STAB only for root qdisc
+    - net: ibm: emac: mal: fix wrong goto
+    - sctp: ensure sk_state is set to CLOSED if hashing fails in sctp_listen_start
+    - netfilter: xtables: avoid NFPROTO_UNSPEC where needed
+    - net: Add l3mdev index to flow struct and avoid oif reset for port devices
+    - netfilter: rpfilter/fib: Populate flowic_l3mdev field
+    - netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
+    - netfilter: fib: check correct rtable in vrf setups
+    - net: rtnetlink: add msg kind names
+    - rtnetlink: Add bulk registration helpers for rtnetlink message handlers.
+    - mctp: Handle error of rtnl_register_module().
+    - ppp: fix ppp_async_encode() illegal access
+    - slip: make slhc_remember() more robust against malicious packets
+    - RDMA/hns: Fix UAF for cq async event
+    - x86/fpu: Avoid writing LBR bit to IA32_XSS unless supported
+    - hwmon: (tmp513) Add missing dependency on REGMAP_I2C
+    - hwmon: (adm9240) Add missing dependency on REGMAP_I2C
+    - hwmon: (adt7470) Add missing dependency on REGMAP_I2C
+    - HID: amd_sfh: Switch to device-managed dmam_alloc_coherent()
+    - resource: fix region_intersects() vs add_memory_driver_managed()
+    - HID: plantronics: Workaround for an unexcepted opposite volume key
+    - Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
+    - usb: dwc3: core: Stop processing of pending events if controller is halted
+    - usb: xhci: Fix problem with xhci resume from suspend
+    - usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
+    - hid: intel-ish-hid: Fix uninitialized variable 'rv' in
+      ish_fw_xfer_direct_dma
+    - drm/v3d: Stop the active perfmon before being destroyed
+    - net: explicitly clear the sk pointer, when pf->create fails
+    - net: Fix an unsafe loop on the list
+    - net: dsa: lan9303: ensure chip reset and wait for READY status
+    - mptcp: pm: do not remove closing subflows
+    - nouveau/dmem: Fix vulnerability in migrate_to_ram upon copy error
+    - kthread: unpark only parked kthread
+    - block, bfq: fix uaf for accessing waker_bfqq after splitting
+    - i2c: smbus: Check for parent device before dereference
+    - net: geneve: add missing netlink policy and size for
+      IFLA_GENEVE_INNER_PROTO_INHERIT
+    - xfrm: Pass flowi_oif or l3mdev as oif to xfrm_dst_lookup
+    - net: Handle l3mdev in ip_tunnel_init_flow
+    - net: seg6: fix seg6_lookup_any_nexthop() to handle VRFs using flowi_l3mdev
+    - net: vrf: determine the dst using the original ifindex for multicast
+    - netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
+    - ext4: fix warning in ext4_dio_write_end_io()
+    - net: axienet: start napi before enabling Rx/Tx
+    - selftests: net: more strict check in net_helper
+    - net: xilinx: axienet: Schedule NAPI in two steps
+    - Linux 5.15.168
+
+  * CVE-2024-36968
+    - Bluetooth: L2CAP: Fix div-by-zero in l2cap_le_flowctl_init()
+
+  * CVE-2024-35904
+    - selinux: avoid dereference of garbage after mount failure
+
+  * IOMMU warnings on AMD systems after booting into kdump kernel
+    (LP: #2080378)
+    - iommu/amd: Simplify and Consolidate Virtual APIC (AVIC) Enablement
+    - iommu/amd: Fix compile warning in init code
+
+  * CVE-2024-42156
+    - s390/pkey: Wipe copies of clear-key structures on failure
+
+  * CVE-2024-44942
+    - f2fs: fix to do sanity check on F2FS_INLINE_DATA flag in inode during GC
+
+  * CVE-2024-38538
+    - net: bridge: xmit: make sure we have at least eth header len bytes
+
+  * CVE-2024-42158
+    - s390/pkey: Use kfree_sensitive() to fix Coccinelle warnings
+
+  * CVE-2024-38667
+    - riscv: prevent pt_regs corruption for secondary idle threads
+
+  * CVE-2024-44940
+    - fou: remove warn in gue_gro_receive on unsupported protocol
+
+  * CVE-2024-42079
+    - gfs2: Fix NULL pointer dereference in gfs2_log_flush
+
+  * CVE-2024-35951
+    - drm/panfrost: Fix the error path in panfrost_mmu_map_fault_addr()
+
+  * LXD fan bridge causes blocked tasks (LP: #2064176)
+    - SAUCE: fan: release rcu_read_lock on skb discard path
+
+  * CVE-2023-52532
+    - net: mana: Fix TX CQE error handling
+
+  * CVE-2023-52621
+    - bpf: Check rcu_read_lock_trace_held() before calling bpf map helpers
+
+  * CVE-2024-26947
+    - ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses
+
+  * CVE-2023-52639
+    - KVM: s390: vsie: fix race during shadow creation
+
+ -- Mehmet Basaran <mehmet.basaran@canonical.com>  Fri, 08 Nov 2024 16:48:16 +0300
+
+linux (5.15.0-126.136) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-126.136 -proposed tracker (LP: #2086027)
+    - [Packaging] resync git-ubuntu-log
+
+  * Cannot detect audio sinks and sources in proposed kernel (LP: #2085082)
+    - soundwire: stream: Revert "soundwire: stream: fix programming slave ports
+      for non-continous port maps"
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 06 Nov 2024 10:28:09 +0100
+
+linux (5.15.0-125.135) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-125.135 -proposed tracker (LP: #2083001)
+
+  * CVE-2024-26800
+    - tls: rx: coalesce exit paths in tls_decrypt_sg()
+    - tls: separate no-async decryption request handling from async
+    - tls: fix use-after-free on failed backlog decryption
+
+  * Please backport the more restrictive XSAVES deactivation for  Zen1/2 arch
+    (LP: #2077321)
+    - x86/CPU/AMD: Improve the erratum 1386 workaround
+
+  * Jammy update: v5.15.167 upstream stable release (LP: #2081279)
+    - drm: panel-orientation-quirks: Add quirk for OrangePi Neo
+    - ALSA: hda/generic: Add a helper to mute speakers at suspend/shutdown
+    - ALSA: hda/conexant: Mute speakers at suspend / shutdown
+    - i2c: Fix conditional for substituting empty ACPI functions
+    - dma-debug: avoid deadlock between dma debug vs printk and netconsole
+    - net: usb: qmi_wwan: add MeiG Smart SRM825L
+    - drm/amdgpu: Fix uninitialized variable warning in amdgpu_afmt_acr
+    - drm/amd/display: Assign linear_pitch_alignment even for VM
+    - drm/amdgpu: fix overflowed array index read warning
+    - drm/amdgpu/pm: Check the return value of smum_send_msg_to_smc
+    - drm/amd/pm: fix uninitialized variable warning for smu8_hwmgr
+    - drm/amd/pm: fix warning using uninitialized value of max_vid_step
+    - drm/amd/pm: fix the Out-of-bounds read warning
+    - drm/amdgpu: fix uninitialized scalar variable warning
+    - drm/amd/pm: fix uninitialized variable warnings for vega10_hwmgr
+    - drm/amdgpu: avoid reading vf2pf info size from FB
+    - drm/amd/display: Check gpio_id before used as array index
+    - drm/amd/display: Stop amdgpu_dm initialize when stream nums greater than 6
+    - drm/amd/display: Add array index check for hdcp ddc access
+    - drm/amd/display: Check num_valid_sets before accessing reader_wm_sets[]
+    - drm/amd/display: Check msg_id before processing transcation
+    - drm/amd/display: Fix Coverity INTEGER_OVERFLOW within
+      dal_gpio_service_create
+    - drm/amd/amdgpu: Check tbo resource pointer
+    - drm/amdgpu/pm: Fix uninitialized variable warning for smu10
+    - drm/amdgpu/pm: Fix uninitialized variable agc_btc_response
+    - drm/amdgpu: Fix out-of-bounds write warning
+    - drm/amdgpu: Fix out-of-bounds read of df_v1_7_channel_number
+    - drm/amdgpu: fix ucode out-of-bounds read warning
+    - drm/amdgpu: fix mc_data out-of-bounds read warning
+    - drm/amdkfd: Reconcile the definition and use of oem_id in struct
+      kfd_topology_device
+    - apparmor: fix possible NULL pointer dereference
+    - drm/amdgpu/pm: Check input value for CUSTOM profile mode setting on legacy
+      SOCs
+    - drm/amdgpu: fix the waring dereferencing hive
+    - drm/amd/pm: check specific index for aldebaran
+    - drm/amdgpu: the warning dereferencing obj for nbio_v7_4
+    - drm/amd/pm: check negtive return for table entries
+    - drm/amdgpu: update type of buf size to u32 for eeprom functions
+    - wifi: iwlwifi: remove fw_running op
+    - cpufreq: scmi: Avoid overflow of target_freq in fast switch
+    - PCI: al: Check IORESOURCE_BUS existence during probe
+    - hwspinlock: Introduce hwspin_lock_bust()
+    - RDMA/efa: Properly handle unexpected AQ completions
+    - ionic: fix potential irq name truncation
+    - rcu/nocb: Remove buggy bypass lock contention mitigation
+    - usbip: Don't submit special requests twice
+    - usb: typec: ucsi: Fix null pointer dereference in trace
+    - fsnotify: clear PARENT_WATCHED flags lazily
+    - smack: tcp: ipv4, fix incorrect labeling
+    - drm/meson: plane: Add error handling
+    - drm/bridge: tc358767: Check if fully initialized before signalling HPD event
+      via IRQ
+    - wifi: cfg80211: make hash table duplicates more survivable
+    - block: remove the blk_flush_integrity call in blk_integrity_unregister
+    - drm/amd/display: Skip wbscl_set_scaler_filter if filter is null
+    - media: uvcvideo: Enforce alignment of frame and interval
+    - drm/amd/pm: Fix the null pointer dereference for vega10_hwmgr
+    - virtio_net: Fix napi_skb_cache_put warning
+    - rcu-tasks: Fix show_rcu_tasks_trace_gp_kthread buffer overflow
+    - ext4: reject casefold inode flag without casefold feature
+    - udf: Limit file size to 4TB
+    - ext4: handle redirtying in ext4_bio_write_page()
+    - i2c: Use IS_REACHABLE() for substituting empty ACPI functions
+    - sch/netem: fix use after free in netem_dequeue
+    - ASoC: dapm: Fix UAF for snd_soc_pcm_runtime object
+    - KVM: SVM: fix emulation of msr reads/writes of MSR_FS_BASE and MSR_GS_BASE
+    - KVM: SVM: Don't advertise Bus Lock Detect to guest if SVM support is missing
+    - ALSA: hda/conexant: Add pincfg quirk to enable top speakers on Sirius
+      devices
+    - ALSA: hda/realtek: add patch for internal mic in Lenovo V145
+    - ALSA: hda/realtek: Support mute LED on HP Laptop 14-dq2xxx
+    - ata: libata: Fix memory leak for error path in ata_host_alloc()
+    - irqchip/gic-v2m: Fix refcount leak in gicv2m_of_init()
+    - rtmutex: Drop rt_mutex::wait_lock before scheduling
+    - nvme-pci: Add sleep quirk for Samsung 990 Evo
+    - Revert "Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE"
+    - Bluetooth: MGMT: Ignore keys being loaded with invalid type
+    - mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K
+    - mmc: sdhci-of-aspeed: fix module autoloading
+    - mmc: cqhci: Fix checking of CQHCI_HALT state
+    - fuse: update stats for pages in dropped aux writeback list
+    - fuse: use unsigned type for getxattr/listxattr size truncation
+    - clk: qcom: clk-alpha-pll: Fix the pll post div mask
+    - clk: qcom: clk-alpha-pll: Fix the trion pll postdiv set rate API
+    - can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open
+    - tracing: Avoid possible softlockup in tracing_iter_reset()
+    - ila: call nf_unregister_net_hooks() sooner
+    - sched: sch_cake: fix bulk flow accounting logic for host fairness
+    - nilfs2: fix missing cleanup on rollforward recovery error
+    - nilfs2: fix state management in error path of log writing function
+    - mptcp: pm: re-using ID of unused flushed subflows
+    - mptcp: pm: only decrement add_addr_accepted for MPJ req
+    - mptcp: pm: check add_addr_accept_max before accepting new ADD_ADDR
+    - mptcp: pm: fullmesh: select the right ID later
+    - mptcp: constify a bunch of of helpers
+    - mptcp: pm: avoid possible UaF when selecting endp
+    - mptcp: avoid duplicated SUB_CLOSED events
+    - mptcp: close subflow when receiving TCP+FIN
+    - mptcp: pm: ADD_ADDR 0 is not a new address
+    - mptcp: pm: do not remove already closed subflows
+    - mptcp: pm: skip connecting to already established sf
+    - mptcp: pr_debug: add missing \n at the end
+    - mptcp: pm: send ACK on an active subflow
+    - ALSA: hda: Add input value sanity checks to HDMI channel map controls
+    - smack: unix sockets: fix accept()ed socket label
+    - irqchip/armada-370-xp: Do not allow mapping IRQ 0 and 1
+    - af_unix: Remove put_pid()/put_cred() in copy_peercred().
+    - iommu: sun50i: clear bypass register
+    - netfilter: nf_conncount: fix wrong variable type
+    - udf: Avoid excessive partition lengths
+    - media: vivid: fix wrong sizeimage value for mplane
+    - leds: spi-byte: Call of_node_put() on error path
+    - wifi: brcmsmac: advertise MFP_CAPABLE to enable WPA3
+    - usb: uas: set host status byte on data completion error
+    - drm/amd/display: Check HDCP returned status
+    - media: vivid: don't set HDMI TX controls if there are no HDMI outputs
+    - PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
+    - media: qcom: camss: Add check for v4l2_fwnode_endpoint_parse
+    - pcmcia: Use resource_size function on resource object
+    - drm/amdgpu: check for LINEAR_ALIGNED correctly in check_tiling_flags_gfx6
+    - can: bcm: Remove proc entry when dev is unregistered.
+    - can: m_can: Release irq on error in m_can_open
+    - igb: Fix not clearing TimeSync interrupts for 82580
+    - platform/x86: dell-smbios: Fix error path in dell_smbios_init()
+    - tcp_bpf: fix return value of tcp_bpf_sendmsg()
+    - igc: Unlock on error in igc_io_resume()
+    - ice: check ICE_VSI_DOWN under rtnl_lock when preparing for reset
+    - net: usb: don't write directly to netdev->dev_addr
+    - usbnet: modern method to get random MAC
+    - bareudp: Fix device stats updates.
+    - gro: remove rcu_read_lock/rcu_read_unlock from gro_receive handlers
+    - gro: remove rcu_read_lock/rcu_read_unlock from gro_complete handlers
+    - fou: Fix null-ptr-deref in GRO.
+    - net: bridge: br_fdb_external_learn_add(): always set EXT_LEARN
+    - net: dsa: vsc73xx: fix possible subblocks range of CAPT block
+    - ASoC: topology: Properly initialize soc_enum values
+    - dm init: Handle minors larger than 255
+    - iommu/vt-d: Handle volatile descriptor status read
+    - cgroup: Protect css->cgroup write under css_set_lock
+    - um: line: always fill *error_out in setup_one_line()
+    - devres: Initialize an uninitialized struct member
+    - pci/hotplug/pnv_php: Fix hotplug driver crash on Powernv
+    - hwmon: (adc128d818) Fix underflows seen when writing limit attributes
+    - hwmon: (lm95234) Fix underflows seen when writing limit attributes
+    - hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
+    - hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
+    - libbpf: Add NULL checks to bpf_object__{prev_map,next_map}
+    - drm/amdgpu: Set no_hw_access when VF request full GPU fails
+    - ext4: fix possible tid_t sequence overflows
+    - dma-mapping: benchmark: Don't starve others when doing the test
+    - wifi: mwifiex: Do not return unused priv in mwifiex_get_priv_by_id()
+    - smp: Add missing destroy_work_on_stack() call in smp_call_on_cpu()
+    - fs/ntfs3: Check more cases when directory is corrupted
+    - btrfs: replace BUG_ON with ASSERT in walk_down_proc()
+    - btrfs: clean up our handling of refs == 0 in snapshot delete
+    - btrfs: replace BUG_ON() with error handling at update_ref_for_cow()
+    - riscv: set trap vector earlier
+    - PCI: Add missing bridge lock to pci_bus_lock()
+    - net: dpaa: avoid on-stack arrays of NR_CPUS elements
+    - i3c: mipi-i3c-hci: Error out instead on BUG_ON() in IBI DMA setup
+    - kselftests: dmabuf-heaps: Ensure the driver name is null-terminated
+    - btrfs: initialize location to fix -Wmaybe-uninitialized in
+      btrfs_lookup_dentry()
+    - s390/vmlinux.lds.S: Move ro_after_init section behind rodata section
+    - HID: cougar: fix slab-out-of-bounds Read in cougar_report_fixup
+    - HID: amd_sfh: free driver_data after destroying hid device
+    - Input: uinput - reject requests with unreasonable number of slots
+    - usbnet: ipheth: race between ipheth_close and error handling
+    - Squashfs: sanity check symbolic link size
+    - of/irq: Prevent device address out-of-bounds read in interrupt map walk
+    - lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc()
+    - MIPS: cevt-r4k: Don't call get_c0_compare_int if timer irq is installed
+    - ata: pata_macio: Use WARN instead of BUG
+    - NFSv4: Add missing rescheduling points in
+      nfs_client_return_marked_delegations
+    - cifs: Check the lease context if we actually got a lease
+    - staging: iio: frequency: ad9834: Validate frequency parameter value
+    - iio: buffer-dmaengine: fix releasing dma channel on error
+    - iio: fix scale application in iio_convert_raw_to_processed_unlocked
+    - iio: adc: ad7124: fix config comparison
+    - iio: adc: ad7124: fix chip ID mismatch
+    - usb: dwc3: core: update LC timer as per USB Spec V3.2
+    - binder: fix UAF caused by offsets overwrite
+    - nvmem: Fix return type of devm_nvmem_device_get() in kerneldoc
+    - uio_hv_generic: Fix kernel NULL pointer dereference in hv_uio_rescind
+    - Drivers: hv: vmbus: Fix rescind handling in uio_hv_generic
+    - VMCI: Fix use-after-free when removing resource in vmci_resource_remove()
+    - clocksource/drivers/imx-tpm: Fix return -ETIME when delta exceeds INT_MAX
+    - clocksource/drivers/imx-tpm: Fix next event not taking effect sometime
+    - clocksource/drivers/timer-of: Remove percpu irq related code
+    - uprobes: Use kzalloc to allocate xol area
+    - perf/aux: Fix AUX buffer serialization
+    - ksmbd: unset the binding mark of a reused connection
+    - ksmbd: Unlock on in ksmbd_tcp_set_interfaces()
+    - nilfs2: replace snprintf in show functions with sysfs_emit
+    - nilfs2: protect references to superblock parameters exposed in sysfs
+    - workqueue: wq_watchdog_touch is always called with valid CPU
+    - workqueue: Improve scalability of workqueue watchdog touch
+    - ACPI: processor: Return an error if acpi_processor_get_info() fails in
+      processor_add()
+    - ACPI: processor: Fix memory leaks in error paths of processor_add()
+    - arm64: acpi: Move get_cpu_for_acpi_id() to a header
+    - arm64: acpi: Harden get_cpu_for_acpi_id() against missing CPU entry
+    - nvmet-tcp: fix kernel crash if commands allocation fails
+    - ASoC: sunxi: sun4i-i2s: fix LRCLK polarity in i2s mode
+    - drm/i915/fence: Mark debug_fence_init_onstack() with __maybe_unused
+    - drm/i915/fence: Mark debug_fence_free() with __maybe_unused
+    - gpio: rockchip: fix OF node leak in probe()
+    - net: more strict VIRTIO_NET_HDR_GSO_UDP_L4 validation
+    - net: change maximum number of UDP segments to 128
+    - gso: fix dodgy bit handling for GSO_UDP_L4
+    - net: drop bad gso csum_start and offset in virtio_net_hdr
+    - x86/mm: Fix PTI for i386 some more
+    - net, sunrpc: Remap EPERM in case of connection failure in
+      xs_tcp_setup_socket
+    - btrfs: fix race between direct IO write and fsync when using same fd
+    - memcg: protect concurrent access to mem_cgroup_idr
+    - udp: fix receiving fraglist GSO packets
+    - Linux 5.15.167
+
+  * CVE-2024-41071
+    - wifi: mac80211: Avoid address calculations via out of bounds array indexing
+
+  * CVE-2024-40915
+    - riscv: rewrite __kernel_map_pages() to fix sleeping in invalid context
+
+  * CVE-2024-38611
+    - media: i2c: et8ek8: Don't strip remove function when driver is builtin
+
+  * CVE-2024-38602
+    - ax25: Fix reference count leak issues of ax25_dev
+
+  * CVE-2024-26669
+    - net/sched: flower: Fix chain template offload
+
+  * CVE-2024-26607
+    - drm/bridge: sii902x: Fix probing race issue
+
+  * Jammy update: v5.15.166 upstream stable release (LP: #2080594)
+    - fuse: Initialize beyond-EOF page contents before setting uptodate
+    - char: xillybus: Don't destroy workqueue from work item running on it
+    - char: xillybus: Refine workqueue handling
+    - char: xillybus: Check USB endpoints when probing device
+    - ALSA: usb-audio: Add delay quirk for VIVO USB-C-XE710 HEADSET
+    - ALSA: usb-audio: Support Yamaha P-125 quirk entry
+    - xhci: Fix Panther point NULL pointer deref at full-speed re-enumeration
+    - thunderbolt: Mark XDomain as unplugged when router is removed
+    - s390/dasd: fix error recovery leading to data corruption on ESE devices
+    - arm64: ACPI: NUMA: initialize all values of acpi_early_node_map to
+      NUMA_NO_NODE
+    - dm resume: don't return EINVAL when signalled
+    - dm persistent data: fix memory allocation failure
+    - vfs: Don't evict inode under the inode lru traversing context
+    - fs/ntfs3: add prefix to bitmap_size() and use BITS_TO_U64()
+    - s390/cio: rename bitmap_size() -> idset_bitmap_size()
+    - btrfs: rename bitmap_set_bits() -> btrfs_bitmap_set_bits()
+    - bitmap: introduce generic optimized bitmap_size()
+    - fix bitmap corruption on close_range() with CLOSE_RANGE_UNSHARE
+    - selinux: fix potential counting error in avc_add_xperms_decision()
+    - btrfs: tree-checker: add dev extent item checks
+    - drm/amdgpu: Actually check flags for all context ops.
+    - memcg_write_event_control(): fix a user-triggerable oops
+    - drm/amdgpu/jpeg2: properly set atomics vmid field
+    - s390/uv: Panic for set and remove shared access UVC errors
+    - igc: Correct the launchtime offset
+    - igc: remove I226 Qbv BaseTime restriction
+    - igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer
+    - net/mlx5e: Correctly report errors for ethtool rx flows
+    - atm: idt77252: prevent use after free in dequeue_rx()
+    - net: axienet: Fix register defines comment description
+    - net: dsa: vsc73xx: pass value in phy_write operation
+    - net: dsa: vsc73xx: use read_poll_timeout instead delay loop
+    - net: dsa: vsc73xx: check busy flag in MDIO operations
+    - mlxbf_gige: Remove two unused function declarations
+    - mlxbf_gige: disable RX filters until RX path initialized
+    - mptcp: correct MPTCP_SUBFLOW_ATTR_SSN_OFFSET reserved size
+    - netfilter: allow ipv6 fragments to arrive on different devices
+    - netfilter: flowtable: initialise extack before use
+    - netfilter: nf_queue: drop packets with cloned unconfirmed conntracks
+    - net: hns3: fix wrong use of semaphore up
+    - net: hns3: fix a deadlock problem when config TC during resetting
+    - ALSA: hda/realtek: Fix noise from speakers on Lenovo IdeaPad 3 15IAU7
+    - ssb: Fix division by zero issue in ssb_calc_clock_rate
+    - wifi: cfg80211: check wiphy mutex is held for wdev mutex
+    - wifi: mac80211: fix BA session teardown race
+    - wifi: cw1200: Avoid processing an invalid TIM IE
+    - i2c: riic: avoid potential division by zero
+    - RDMA/rtrs: Fix the problem of variable not initialized fully
+    - s390/smp,mcck: fix early IPI handling
+    - i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
+    - i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
+    - media: radio-isa: use dev_name to fill in bus_info
+    - staging: iio: resolver: ad2s1210: fix use before initialization
+    - drm/amd/display: Validate hw_points_num before using it
+    - staging: ks7010: disable bh on tx_dev_lock
+    - binfmt_misc: cleanup on filesystem umount
+    - media: qcom: venus: fix incorrect return value
+    - scsi: spi: Fix sshdr use
+    - gfs2: setattr_chown: Add missing initialization
+    - wifi: iwlwifi: abort scan when rfkill on but device enabled
+    - wifi: iwlwifi: fw: Fix debugfs command sending
+    - IB/hfi1: Fix potential deadlock on &irq_src_lock and &dd->uctxt_lock
+    - hwmon: (ltc2992) Avoid division by zero
+    - arm64: Fix KASAN random tag seed initialization
+    - memory: tegra: Skip SID programming if SID registers aren't set
+    - powerpc/xics: Check return value of kasprintf in icp_native_map_one_cpu
+    - nvmet-trace: avoid dereferencing pointer too early
+    - ext4: do not trim the group with corrupted block bitmap
+    - afs: fix __afs_break_callback() / afs_drop_open_mmap() race
+    - fuse: fix UAF in rcu pathwalks
+    - quota: Remove BUG_ON from dqget()
+    - media: pci: cx23885: check cx23885_vdev_init() return
+    - fs: binfmt_elf_efpic: don't use missing interpreter's properties
+    - scsi: lpfc: Initialize status local variable in lpfc_sli4_repost_sgl_list()
+    - media: drivers/media/dvb-core: copy user arrays safely
+    - net/sun3_82586: Avoid reading past buffer in debug output
+    - drm/lima: set gp bus_stop bit before hard reset
+    - virtiofs: forbid newlines in tags
+    - clocksource/drivers/arm_global_timer: Guard against division by zero
+    - netlink: hold nlk->cb_mutex longer in __netlink_dump_start()
+    - md: clean up invalid BUG_ON in md_ioctl
+    - x86: Increase brk randomness entropy for 64-bit systems
+    - memory: stm32-fmc2-ebi: check regmap_read return value
+    - parisc: Use irq_enter_rcu() to fix warning at kernel/context_tracking.c:367
+    - powerpc/boot: Handle allocation failure in simple_realloc()
+    - powerpc/boot: Only free if realloc() succeeds
+    - btrfs: change BUG_ON to assertion when checking for delayed_node root
+    - btrfs: handle invalid root reference found in may_destroy_subvol()
+    - btrfs: send: handle unexpected data in header buffer in begin_cmd()
+    - btrfs: change BUG_ON to assertion in tree_move_down()
+    - btrfs: delete pointless BUG_ON check on quota root in
+      btrfs_qgroup_account_extent()
+    - f2fs: fix to do sanity check in update_sit_entry
+    - usb: gadget: fsl: Increase size of name buffer for endpoints
+    - Bluetooth: bnep: Fix out-of-bound access
+    - net: hns3: add checking for vf id of mailbox
+    - nvmet-tcp: do not continue for invalid icreq
+    - NFS: avoid infinite loop in pnfs_update_layout.
+    - openrisc: Call setup_memory() earlier in the init sequence
+    - s390/iucv: fix receive buffer virtual vs physical address confusion
+    - clocksource: Make watchdog and suspend-timing multiplication overflow safe
+    - platform/x86: lg-laptop: fix %s null argument warning
+    - usb: dwc3: core: Skip setting event buffers for host only controllers
+    - irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
+    - ext4: set the type of max_zeroout to unsigned int to avoid overflow
+    - nvmet-rdma: fix possible bad dereference when freeing rsps
+    - hrtimer: Prevent queuing of hrtimer without a function callback
+    - gtp: pull network headers in gtp_dev_xmit()
+    - block: use "unsigned long" for blk_validate_block_size().
+    - nfsd: move reply cache initialization into nfsd startup
+    - nfsd: move init of percpu reply_cache_stats counters back to nfsd_init_net
+    - NFSD: Refactor nfsd_reply_cache_free_locked()
+    - NFSD: Rename nfsd_reply_cache_alloc()
+    - NFSD: Replace nfsd_prune_bucket()
+    - NFSD: Refactor the duplicate reply cache shrinker
+    - NFSD: Rewrite synopsis of nfsd_percpu_counters_init()
+    - NFSD: Fix frame size warning in svc_export_parse()
+    - sunrpc: don't change ->sv_stats if it doesn't exist
+    - nfsd: stop setting ->pg_stats for unused stats
+    - sunrpc: pass in the sv_stats struct through svc_create_pooled
+    - sunrpc: remove ->pg_stats from svc_program
+    - sunrpc: use the struct net as the svc proc private
+    - nfsd: rename NFSD_NET_* to NFSD_STATS_*
+    - nfsd: expose /proc/net/sunrpc/nfsd in net namespaces
+    - nfsd: make all of the nfsd stats per-network namespace
+    - nfsd: remove nfsd_stats, make th_cnt a global counter
+    - nfsd: make svc_stat per-network namespace instead of global
+    - media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)
+    - dm suspend: return -ERESTARTSYS instead of -EINTR
+    - net: mana: Fix doorbell out of order violation and avoid unnecessary
+      doorbell rings
+    - platform/surface: aggregator: Fix warning when controller is destroyed in
+      probe
+    - Bluetooth: hci_core: Fix LE quote calculation
+    - Bluetooth: SMP: Fix assumption of Central always being Initiator
+    - tc-testing: don't access non-existent variable on exception
+    - kcm: Serialise kcm_sendmsg() for the same socket.
+    - netfilter: nft_counter: Disable BH in nft_counter_offload_stats().
+    - netfilter: nft_counter: Synchronize nft_counter_reset() against reader.
+    - ip6_tunnel: Fix broken GRO
+    - bonding: fix bond_ipsec_offload_ok return type
+    - bonding: fix null pointer deref in bond_ipsec_offload_ok
+    - bonding: fix xfrm real_dev null pointer dereference
+    - bonding: fix xfrm state handling when clearing active slave
+    - ice: fix ICE_LAST_OFFSET formula
+    - dpaa2-switch: Fix error checking in dpaa2_switch_seed_bp()
+    - net: dsa: mv88e6xxx: read FID when handling ATU violations
+    - net: dsa: mv88e6xxx: replace ATU violation prints with trace points
+    - net: dsa: mv88e6xxx: Fix out-of-bound access
+    - ipv6: prevent UAF in ip6_send_skb()
+    - ipv6: fix possible UAF in ip6_finish_output2()
+    - ipv6: prevent possible UAF in ip6_xmit()
+    - netfilter: flowtable: validate vlan header
+    - net: xilinx: axienet: Always disable promiscuous mode
+    - net: xilinx: axienet: Fix dangling multicast addresses
+    - drm/msm/dpu: don't play tricks with debug macros
+    - drm/msm/dp: reset the link phy params before link training
+    - drm/msm/dpu: cleanup FB if dpu_format_populate_layout fails
+    - mmc: mmc_test: Fix NULL dereference on allocation failure
+    - Bluetooth: MGMT: Add error handling to pair_device()
+    - scsi: core: Fix the return value of scsi_logical_block_count()
+    - MIPS: Loongson64: Set timer mode in cpu-probe
+    - HID: wacom: Defer calculation of resolution until resolution_code is known
+    - HID: microsoft: Add rumble support to latest xbox controllers
+    - cxgb4: add forgotten u64 ivlan cast before shift
+    - KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3
+    - mmc: dw_mmc: allow biu and ciu clocks to defer
+    - Revert "drm/amd/display: Validate hw_points_num before using it"
+    - hwmon: (ltc2992) Fix memory leak in ltc2992_parse_dt()
+    - ALSA: timer: Relax start tick time check for slave timer elements
+    - mm/numa: no task_numa_fault() call if PMD is changed
+    - mm/numa: no task_numa_fault() call if PTE is changed
+    - Input: MT - limit max slots
+    - tools: move alignment-related macros to new <linux/align.h>
+    - btrfs: run delayed iputs when flushing delalloc
+    - pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins
+    - pinctrl: single: fix potential NULL dereference in pcs_get_function()
+    - wifi: mwifiex: duplicate static structs used in driver instances
+    - net: mana: Fix race of mana_hwc_post_rx_wqe and new hwc response
+    - mptcp: sched: check both backup in retrans
+    - Revert "MIPS: Loongson64: reset: Prioritise firmware service"
+    - drm/amdkfd: don't allow mapping the MMIO HDP page with large pages
+    - ata: libata-core: Fix null pointer dereference on error
+    - cgroup/cpuset: Prevent UAF in proc_cpuset_show()
+    - net:rds: Fix possible deadlock in rds_message_put
+    - soundwire: stream: fix programming slave ports for non-continous port maps
+    - PM: core: Remove DEFINE_UNIVERSAL_DEV_PM_OPS() macro
+    - PM: core: Add EXPORT[_GPL]_SIMPLE_DEV_PM_OPS macros
+    - PM: runtime: Add DEFINE_RUNTIME_DEV_PM_OPS() macro
+    - phy: xilinx: add runtime PM support
+    - phy: xilinx: phy-zynqmp: dynamic clock support for power-save
+    - phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
+    - dmaengine: dw: Add peripheral bus width verification
+    - dmaengine: dw: Add memory bus width verification
+    - ethtool: check device is present when getting link settings
+    - gtp: fix a potential NULL pointer dereference
+    - net: busy-poll: use ktime_get_ns() instead of local_clock()
+    - nfc: pn533: Add poll mod list filling check
+    - soc: qcom: cmd-db: Map shared memory as WC, not WB
+    - cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
+    - USB: serial: option: add MeiG Smart SRM825L
+    - usb: dwc3: omap: add missing depopulate in probe error path
+    - usb: dwc3: core: Prevent USB core invalid event buffer address access
+    - usb: dwc3: st: fix probed platform device ref count on probe error path
+    - usb: dwc3: st: add missing depopulate in probe error path
+    - usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in
+      remove_power_attributes()
+    - usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
+    - usb: cdnsp: fix for Link TRB with TC
+    - phy: zynqmp: Enable reference clock correctly
+    - igc: Fix reset adapter logics when tx mode change
+    - igc: Fix qbv tx latency by setting gtxoffset
+    - scsi: aacraid: Fix double-free on probe failure
+    - apparmor: fix policy_unpack_test on big endian systems
+    - Linux 5.15.166
+
+  * CVE-2024-26893
+    - firmware: arm_scmi: Fix double free in SMC transport cleanup path
+
+  * [22.10 FEAT] KVM: Secure Execution guest dump encryption with customer keys
+    - kernel part (LP: #1959940)
+    - s390: uv: Add offset comments to UV query struct and fix naming
+    - s390/uv: Add SE hdr query information
+    - s390/uv: Add dump fields to query
+    - KVM: s390: pv: Add query interface
+    - KVM: s390: pv: Add dump support definitions
+    - KVM: s390: pv: Add query dump information
+    - KVM: s390: Add configuration dump functionality
+    - KVM: s390: Add CPU dump functionality
+    - KVM: s390: Add KVM_CAP_S390_PROTECTED_DUMP
+    - Documentation: KVM: add separate directories for architecture-specific
+      documentation
+    - Documentation: virt: Protected virtual machine dumps
+    - Documentation/virt/kvm/api.rst: Add protvirt dump/info api descriptions
+    - Documentation/virt/kvm/api.rst: Explain rc/rrc delivery
+
+  * turbostat fails with too many open files on large systems (LP: #2069961)
+    - tools/power turbostat: Increase the limit for fd opened
+
+  * Jammy update: v5.15.165 upstream stable release (LP: #2078428)
+    - f2fs: fix return value of f2fs_convert_inline_inode()
+    - f2fs: fix to don't dirty inode for readonly filesystem
+    - EDAC, i10nm: make skx_common.o a separate module
+    - platform/chrome: cros_ec_debugfs: fix wrong EC message version
+    - block: refactor to use helper
+    - block: cleanup bio_integrity_prep
+    - block: initialize integrity buffer to zero before writing it to media
+    - hfsplus: fix to avoid false alarm of circular locking
+    - x86/of: Return consistent error type from x86_of_pci_irq_enable()
+    - x86/pci/intel_mid_pci: Fix PCIBIOS_* return code handling
+    - x86/pci/xen: Fix PCIBIOS_* return code handling
+    - x86/platform/iosf_mbi: Convert PCIBIOS_* return codes to errnos
+    - hwmon: (adt7475) Fix default duty on fan is disabled
+    - pwm: stm32: Always do lazy disabling
+    - drm/meson: fix canvas release in bind function
+    - hwmon: (max6697) Fix underflow when writing limit attributes
+    - hwmon: (max6697) Fix swapped temp{1,8} critical alarms
+    - arm64: dts: qcom: sdm845: add power-domain to UFS PHY
+    - arm64: dts: qcom: sm8250: switch UFS QMP PHY to new style of bindings
+    - arm64: dts: qcom: sm8250: add power-domain to UFS PHY
+    - soc: qcom: rpmh-rsc: Ensure irqs aren't disabled by rpmh_rsc_send_data()
+      callers
+    - arm64: dts: qcom: msm8996: specify UFS core_clk frequencies
+    - memory: fsl_ifc: Make FSL_IFC config visible and selectable
+    - soc: qcom: pdr: protect locator_addr with the main mutex
+    - soc: qcom: pdr: fix parsing of domains lists
+    - arm64: dts: rockchip: Increase VOP clk rate on RK3328
+    - ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node
+    - ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
+    - ARM: dts: imx6qdl-kontron-samx6i: fix board reset
+    - ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
+    - ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
+    - arm64: dts: mediatek: mt8183-kukui: Drop bogus output-enable property
+    - arm64: dts: mediatek: mt7622: fix "emmc" pinctrl mux
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add ports node for anx7625
+    - arm64: dts: amlogic: gx: correct hdmi clocks
+    - m68k: atari: Fix TT bootup freeze / unexpected (SCU) interrupt messages
+    - x86/xen: Convert comma to semicolon
+    - m68k: cmpxchg: Fix return value for default case in __arch_xchg()
+    - ARM: pxa: spitz: use gpio descriptors for audio
+    - ARM: spitz: fix GPIO assignment for backlight
+    - vmlinux.lds.h: catch .bss..L* sections into BSS")
+    - firmware: turris-mox-rwtm: Do not complete if there are no waiters
+    - firmware: turris-mox-rwtm: Fix checking return value of
+      wait_for_completion_timeout()
+    - firmware: turris-mox-rwtm: Initialize completion before mailbox
+    - wifi: brcmsmac: LCN PHY code is used for BCM4313 2G-only device
+    - selftests/bpf: Fix prog numbers in test_sockmap
+    - net: esp: cleanup esp_output_tail_tcp() in case of unsupported ESPINTCP
+    - tcp: annotate lockless accesses to sk->sk_err_soft
+    - tcp: annotate lockless access to sk->sk_err
+    - tcp: add tcp_done_with_error() helper
+    - tcp: fix race in tcp_write_err()
+    - tcp: fix races in tcp_v[46]_err()
+    - net/smc: set rmb's SG_MAX_SINGLE_ALLOC limitation only when
+      CONFIG_ARCH_NO_SG_CHAIN is defined
+    - selftests/bpf: Check length of recv in test_sockmap
+    - lib: objagg: Fix general protection fault
+    - mlxsw: spectrum_acl_erp: Fix object nesting warning
+    - mlxsw: spectrum_acl_bloom_filter: Make mlxsw_sp_acl_bf_key_encode() more
+      flexible
+    - mlxsw: spectrum_acl: Fix ACL scale regression and firmware errors
+    - wifi: ath11k: fix wrong handling of CCMP256 and GCMP ciphers
+    - wifi: cfg80211: fix typo in cfg80211_calculate_bitrate_he()
+    - wifi: cfg80211: handle 2x996 RU allocation in
+      cfg80211_calculate_bitrate_he()
+    - net: fec: Refactor: #define magic constants
+    - net: fec: Fix FEC_ECR_EN1588 being cleared on link-down
+    - libbpf: Checking the btf_type kind when fixing variable offsets
+    - ipvs: Avoid unnecessary calls to skb_is_gso_sctp
+    - netfilter: nf_tables: rise cap on SELinux secmark context
+    - perf/x86/intel/pt: Fix pt_topa_entry_for_page() address calculation
+    - perf: Fix perf_aux_size() for greater-than 32-bit size
+    - perf: Prevent passing zero nr_pages to rb_alloc_aux()
+    - perf: Fix default aux_watermark calculation
+    - wifi: virt_wifi: avoid reporting connection success with wrong SSID
+    - gss_krb5: Fix the error handling path for crypto_sync_skcipher_setkey
+    - wifi: virt_wifi: don't use strlen() in const context
+    - locking/rwsem: Add __always_inline annotation to __down_write_common() and
+      inlined callers
+    - selftests/bpf: Close fd in error path in drop_on_reuseport
+    - bpf: annotate BTF show functions with __printf
+    - bna: adjust 'name' buf size of bna_tcb and bna_ccb structures
+    - bpf: Eliminate remaining "make W=1" warnings in kernel/bpf/btf.o
+    - selftests: forwarding: devlink_lib: Wait for udev events after reloading
+    - xdp: fix invalid wait context of page_pool_destroy()
+    - drm/amd/pm: Fix aldebaran pcie speed reporting
+    - drm/amdgpu: Check if NBIO funcs are NULL in amdgpu_device_baco_exit
+    - drm/panel: boe-tv101wum-nl6: If prepare fails, disable GPIO before
+      regulators
+    - drm/panel: boe-tv101wum-nl6: Check for errors on the NOP in prepare()
+    - media: dvb-usb: Fix unexpected infinite loop in
+      dvb_usb_read_remote_control()
+    - media: imon: Fix race getting ictx->lock
+    - media: i2c: Fix imx412 exposure control
+    - saa7134: Unchecked i2c_transfer function result fixed
+    - media: uvcvideo: Override default flags
+    - media: renesas: vsp1: Fix _irqsave and _irq mix
+    - media: renesas: vsp1: Store RPF partition configuration per RPF instance
+    - drm/mediatek: Add missing plane settings when async update
+    - drm/mediatek: Add DRM_MODE_ROTATE_0 to rotation property
+    - leds: trigger: Unregister sysfs attributes before calling deactivate()
+    - perf report: Fix condition in sort__sym_cmp()
+    - drm/etnaviv: fix DMA direction handling for cached RW buffers
+    - drm/qxl: Add check for drm_cvt_mode
+    - Revert "leds: led-core: Fix refcount leak in of_led_get()"
+    - ext4: fix infinite loop when replaying fast_commit
+    - media: venus: flush all buffers in output plane streamoff
+    - perf intel-pt: Fix aux_watermark calculation for 64-bit size
+    - perf intel-pt: Fix exclude_guest setting
+    - mfd: rsmu: Split core code into separate module
+    - mfd: omap-usb-tll: Use struct_size to allocate tll
+    - xprtrdma: Fix rpcrdma_reqs_reset()
+    - SUNRPC: avoid soft lockup when transmitting UDP to reachable server.
+    - NFSv4.1 another fix for EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - ext4: return early for non-eligible fast_commit track events
+    - ext4: don't track ranges in fast_commit if inode has inlined data
+    - ext4: avoid writing unitialized memory to disk in EA inodes
+    - sparc64: Fix incorrect function signature and add prototype for
+      prom_cif_init
+    - SUNRPC: Fixup gss_status tracepoint error output
+    - PCI: Fix resource double counting on remove & rescan
+    - clk: qcom: branch: Add helper functions for setting retain bits
+    - clk: qcom: gcc-sc7280: Update force mem core bit for UFS ICE clock
+    - coresight: Fix ref leak when of_coresight_parse_endpoint() fails
+    - RDMA/mlx5: Set mkeys for dmabuf at PAGE_SIZE
+    - RDMA/cache: Release GID table even if leak is detected
+    - Input: qt1050 - handle CHIP_ID reading error
+    - RDMA/mlx4: Fix truncated output warning in mad.c
+    - RDMA/mlx4: Fix truncated output warning in alias_GUID.c
+    - RDMA/rxe: Don't set BTH_ACK_MASK for UC or UD QPs
+    - ASoC: max98088: Check for clk_prepare_enable() error
+    - mtd: make mtd_test.c a separate module
+    - RDMA/device: Return error earlier if port in not valid
+    - Input: elan_i2c - do not leave interrupt disabled on suspend failure
+    - PCI: endpoint: Clean up error handling in vpci_scan_bus()
+    - vhost/vsock: always initialize seqpacket_allow
+    - net: missing check virtio
+    - MIPS: Octeron: remove source file executable bit
+    - powerpc/xmon: Fix disassembly CPU feature checks
+    - macintosh/therm_windtunnel: fix module unload.
+    - RDMA/hns: Fix missing pagesize and alignment check in FRMR
+    - RDMA/hns: Fix undifined behavior caused by invalid max_sge
+    - RDMA/hns: Fix insufficient extend DB for VFs.
+    - bnxt_re: Fix imm_data endianness
+    - netfilter: ctnetlink: use helper function to calculate expect ID
+    - netfilter: nf_set_pipapo: fix initial map fill
+    - net: dsa: mv88e6xxx: Limit chip-wide frame size config to CPU ports
+    - net: dsa: b53: Limit chip-wide jumbo frame config to CPU ports
+    - fs/ntfs3: Use ALIGN kernel macro
+    - fs/ntfs3: Merge synonym COMPRESSION_UNIT and NTFS_LZNT_CUNIT
+    - fs/ntfs3: Fix transform resident to nonresident for compressed files
+    - fs/ntfs3: Missed NI_FLAG_UPDATE_PARENT setting
+    - fs/ntfs3: Fix getting file type
+    - pinctrl: rockchip: update rk3308 iomux routes
+    - pinctrl: core: fix possible memory leak when pinctrl_enable() fails
+    - pinctrl: single: fix possible memory leak when pinctrl_enable() fails
+    - pinctrl: ti: ti-iodelay: Drop if block with always false condition
+    - pinctrl: ti: ti-iodelay: fix possible memory leak when pinctrl_enable()
+      fails
+    - pinctrl: freescale: mxs: Fix refcount of child
+    - fs/ntfs3: Replace inode_trylock with inode_lock
+    - fs/ntfs3: Fix field-spanning write in INDEX_HDR
+    - fs/proc/task_mmu: indicate PM_FILE for PMD-mapped file THP
+    - nilfs2: avoid undefined behavior in nilfs_cnt32_ge macro
+    - rtc: interface: Add RTC offset to alarm after fix-up
+    - fs/ntfs3: Missed error return
+    - landlock: Don't lose track of restrictions on cred_transfer
+    - mm/hugetlb: fix possible recursive locking detected warning
+    - mm: mmap_lock: replace get_memcg_path_buf() with on-stack buffer
+    - dt-bindings: thermal: correct thermal zone node name limit
+    - tick/broadcast: Make takeover of broadcast hrtimer reliable
+    - net: netconsole: Disable target before netpoll cleanup
+    - af_packet: Handle outgoing VLAN packets without hardware offloading
+    - ipv6: take care of scope when choosing the src addr
+    - sched/fair: set_load_weight() must also call reweight_task() for SCHED_IDLE
+      tasks
+    - fuse: verify {g,u}id mount options correctly
+    - char: tpm: Fix possible memory leak in tpm_bios_measurements_open()
+    - media: venus: fix use after free in vdec_close
+    - ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error
+    - hfs: fix to initialize fields of hfs_inode_info after hfs_alloc_inode()
+    - ext2: Verify bitmap and itable block numbers before using them
+    - drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes
+    - drm/gma500: fix null pointer dereference in psb_intel_lvds_get_modes
+    - scsi: qla2xxx: Fix optrom version displayed in FDMI
+    - drm/amd/display: Check for NULL pointer
+    - sched/fair: Use all little CPUs for CPU-bound workloads
+    - apparmor: use kvfree_sensitive to free data->data
+    - task_work: s/task_work_cancel()/task_work_cancel_func()/
+    - task_work: Introduce task_work_cancel() again
+    - udf: Avoid using corrupted block bitmap buffer
+    - m68k: amiga: Turn off Warp1260 interrupts during boot
+    - ext4: check dot and dotdot of dx_root before making dir indexed
+    - ext4: make sure the first directory block is not a hole
+    - io_uring: tighten task exit cancellations
+    - selftests/landlock: Add cred_transfer test
+    - wifi: mwifiex: Fix interface type change
+    - leds: ss4200: Convert PCIBIOS_* return codes to errnos
+    - jbd2: make jbd2_journal_get_max_txn_bufs() internal
+    - media: uvcvideo: Fix integer overflow calculating timestamp
+    - KVM: VMX: Split out the non-virtualization part of vmx_interrupt_blocked()
+    - ALSA: usb-audio: Fix microphone sound on HD webcam.
+    - ALSA: usb-audio: Move HD Webcam quirk to the right place
+    - ALSA: usb-audio: Add a quirk for Sonix HD USB Camera
+    - tools/memory-model: Fix bug in lock.cat
+    - hwrng: amd - Convert PCIBIOS_* return codes to errnos
+    - PCI: hv: Return zero, not garbage, when reading PCI_INTERRUPT_PIN
+    - PCI: dw-rockchip: Fix initial PERST# GPIO value
+    - PCI: rockchip: Use GPIOD_OUT_LOW flag while requesting ep_gpio
+    - binder: fix hang of unregistered readers
+    - dev/parport: fix the array out-of-bounds risk
+    - fs/ntfs3: Update log->page_{mask,bits} if log->page_size changed
+    - scsi: qla2xxx: Return ENOBUFS if sg_cnt is more than one for ELS cmds
+    - clk: davinci: da8xx-cfgchip: Initialize clk_init_data before use
+    - ubi: eba: properly rollback inside self_check_eba
+    - decompress_bunzip2: fix rare decompression failure
+    - kbuild: Fix '-S -c' in x86 stack protector scripts
+    - kobject_uevent: Fix OOB access within zap_modalias_env()
+    - gve: Fix an edge case for TSO skb validity check
+    - devres: Fix devm_krealloc() wasting memory
+    - devres: Fix memory leakage caused by driver API devm_free_percpu()
+    - mm/numa_balancing: teach mpol_to_str about the balancing mode
+    - rtc: cmos: Fix return value of nvmem callbacks
+    - scsi: qla2xxx: During vport delete send async logout explicitly
+    - scsi: qla2xxx: Unable to act on RSCN for port online
+    - scsi: qla2xxx: Fix for possible memory corruption
+    - scsi: qla2xxx: Use QP lock to search for bsg
+    - scsi: qla2xxx: Fix flash read failure
+    - scsi: qla2xxx: Complete command early within lock
+    - scsi: qla2xxx: validate nvme_local_port correctly
+    - perf: Fix event leak upon exit
+    - perf: Fix event leak upon exec and file release
+    - perf/x86/intel/uncore: Fix the bits of the CHA extended umask for SPR
+    - perf/x86/intel/pt: Fix topa_entry base length
+    - perf/x86/intel/pt: Fix a topa_entry base address calculation
+    - drm/i915/gt: Do not consider preemption during execlists_dequeue for gen8
+    - drm/amdgpu/sdma5.2: Update wptr registers as well as doorbell
+    - drm/i915/dp: Reset intel_dp->link_trained before retraining the link
+    - rtc: isl1208: Fix return value of nvmem callbacks
+    - watchdog/perf: properly initialize the turbo mode timestamp and rearm
+      counter
+    - platform: mips: cpu_hwmon: Disable driver on unsupported hardware
+    - RDMA/iwcm: Fix a use-after-free related to destroying CM IDs
+    - selftests/sigaltstack: Fix ppc64 GCC build
+    - rbd: don't assume rbd_is_lock_owner() for exclusive mappings
+    - remoteproc: stm32_rproc: Fix mailbox interrupts queuing
+    - remoteproc: imx_rproc: Skip over memory region when node value is NULL
+    - MIPS: ip30: ip30-console: Add missing include
+    - MIPS: dts: loongson: Fix GMAC phy node
+    - MIPS: Loongson64: env: Hook up Loongsson-2K
+    - MIPS: Loongson64: Remove memory node for builtin-dtb
+    - MIPS: Loongson64: reset: Prioritise firmware service
+    - MIPS: Loongson64: Test register availability before use
+    - drm/panfrost: Mark simple_ondemand governor as softdep
+    - rbd: rename RBD_LOCK_STATE_RELEASING and releasing_wait
+    - rbd: don't assume RBD_LOCK_STATE_LOCKED for exclusive mappings
+    - Bluetooth: btusb: Add RTL8852BE device 0489:e125 to device tables
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x13d3:0x3591
+    - nilfs2: handle inconsistent state in nilfs_btnode_create_block()
+    - io_uring/io-wq: limit retrying worker initialisation
+    - kernel: rerun task_work while freezing in get_signal()
+    - kdb: address -Wformat-security warnings
+    - kdb: Use the passed prompt in kdb_position_cursor()
+    - jfs: Fix array-index-out-of-bounds in diFree
+    - dmaengine: ti: k3-udma: Fix BCHAN count with UHC and HC channels
+    - phy: cadence-torrent: Check return value on register read
+    - um: time-travel: fix time-travel-start option
+    - um: time-travel: fix signal blocking race/hang
+    - libbpf: Fix no-args func prototype BTF dumping syntax
+    - dma: fix call order in dmam_free_coherent
+    - bpf, events: Use prog to emit ksymbol event for main program
+    - MIPS: SMP-CPS: Fix address for GCR_ACCESS register for CM3 and later
+    - ipv4: Fix incorrect source address in Record Route option
+    - net: bonding: correctly annotate RCU in bond_should_notify_peers()
+    - netfilter: nft_set_pipapo_avx2: disable softinterrupts
+    - tipc: Return non-zero value from tipc_udp_addr2str() on error
+    - net: stmmac: Correct byte order of perfect_match
+    - net: nexthop: Initialize all fields in dumped nexthops
+    - bpf: Fix a segment issue when downgrading gso_size
+    - mISDN: Fix a use after free in hfcmulti_tx()
+    - apparmor: Fix null pointer deref when receiving skb during sock creation
+    - powerpc: fix a file leak in kvm_vcpu_ioctl_enable_cap()
+    - lirc: rc_dev_get_from_fd(): fix file leak
+    - spi: spidev: Make probe to fail early if a spidev compatible is used
+    - spi: spidev: Replace ACPI specific code by device_get_match_data()
+    - spi: spidev: Replace OF specific code by device property API
+    - spidev: Add Silicon Labs EM3581 device compatible
+    - spi: spidev: order compatibles alphabetically
+    - spi: spidev: add correct compatible for Rohm BH2228FV
+    - ASoC: Intel: use soc_intel_is_byt_cr() only when IOSF_MBI is reachable
+    - ceph: fix incorrect kmalloc size of pagevec mempool
+    - iommu: sprd: Avoid NULL deref in sprd_iommu_hw_en
+    - nvme: split command copy into a helper
+    - nvme: separate command prep and issue
+    - nvme-pci: add missing condition check for existence of mapped data
+    - fs: don't allow non-init s_user_ns for filesystems without FS_USERNS_MOUNT
+    - powerpc/configs: Update defconfig with now user-visible CONFIG_FSL_IFC
+    - arm64: dts: qcom: msm8996: Move '#clock-cells' to QMP PHY child node
+    - arm64: dts: qcom: msm8998: drop USB PHY clock index
+    - arm64: dts: qcom: msm8998: switch USB QMP PHY to new style of bindings
+    - arm64: dts: qcom: msm8998: Disable SS instance in Parkmode for USB
+    - arm64: dts: qcom: ipq8074: Disable SS instance in Parkmode for USB
+    - sysctl: always initialize i_uid/i_gid
+    - ext4: make ext4_es_insert_extent() return void
+    - ext4: refactor ext4_da_map_blocks()
+    - ext4: convert to exclusive lock while inserting delalloc extents
+    - ext4: factor out a common helper to query extent map
+    - ext4: check the extent status again before inserting delalloc block
+    - soc: xilinx: move PM_INIT_FINALIZE to zynqmp_pm_domains driver
+    - drivers: soc: xilinx: check return status of get_api_version()
+    - leds: trigger: use RCU to protect the led_cdevs list
+    - leds: trigger: Remove unused function led_trigger_rename_static()
+    - leds: trigger: Store brightness set by led_trigger_event()
+    - leds: trigger: Call synchronize_rcu() before calling trig->activate()
+    - leds: triggers: Flush pending brightness before activating trigger
+    - irqdomain: Fixed unbalanced fwnode get and put
+    - genirq: Allow the PM device to originate from irq domain
+    - irqchip/imx-irqsteer: Constify irq_chip struct
+    - irqchip/imx-irqsteer: Add runtime PM support
+    - irqchip/imx-irqsteer: Handle runtime power management correctly
+    - drm/dp_mst: Fix all mstb marked as not probed after suspend/resume
+    - remoteproc: imx_rproc: Fix refcount mistake in imx_rproc_addr_init
+    - MIPS: Loongson64: DTS: Add RTC support to Loongson-2K1000
+    - MIPS: Loongson64: DTS: Fix PCIe port nodes for ls7a
+    - MIPS: dts: loongson: Fix liointc IRQ polarity
+    - MIPS: dts: loongson: Fix ls2k1000-rtc interrupt
+    - drm/nouveau: prime: fix refcount underflow
+    - drm/vmwgfx: Fix overlay when using Screen Targets
+    - sched: act_ct: take care of padding in struct zones_ht_key
+    - ALSA: hda: conexant: Fix headset auto detect fail in the polling mode
+    - rtnetlink: enable alt_ifname for setlink/newlink
+    - rtnetlink: Don't ignore IFLA_TARGET_NETNSID when ifname is specified in
+      rtnl_dellink().
+    - net/iucv: fix use after free in iucv_sock_close()
+    - net: mvpp2: Don't re-use loop iterator
+    - netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init().
+    - netfilter: iptables: Fix potential null-ptr-deref in
+      ip6table_nat_table_init().
+    - net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptys
+    - ipv6: fix ndisc_is_useropt() handling for PIO
+    - riscv/mm: Add handling for VM_FAULT_SIGSEGV in mm_fault_error()
+    - power: supply: bq24190_charger: replace deprecated strncpy with strscpy
+    - platform/chrome: cros_ec_proto: Lock device when updating MKBP version
+    - HID: wacom: Modify pen IDs
+    - protect the fetch of ->fd[fd] in do_dup2() from mispredictions
+    - ALSA: usb-audio: Correct surround channels in UAC1 channel map
+    - ALSA: hda/realtek: Add quirk for Acer Aspire E5-574G
+    - Revert "ALSA: firewire-lib: obsolete workqueue for period update"
+    - Revert "ALSA: firewire-lib: operate for period elapse event in process
+      context"
+    - drm/vmwgfx: Fix a deadlock in dma buf fence polling
+    - net: usb: sr9700: fix uninitialized variable use in sr_mdio_read
+    - r8169: don't increment tx_dropped in case of NETDEV_TX_BUSY
+    - mptcp: fix duplicate data handling
+    - netfilter: ipset: Add list flush to cancel_gc
+    - genirq: Allow irq_chip registration functions to take a const irq_chip
+    - irqchip/mbigen: Fix mbigen node address layout
+    - x86/mm: Fix pti_clone_pgtable() alignment assumption
+    - x86/mm: Fix pti_clone_entry_text() for i386
+    - sctp: move hlist_node and hashent out of sctp_ep_common
+    - sctp: Fix null-ptr-deref in reuseport_add_sock().
+    - net: usb: qmi_wwan: fix memory leak for not ip packets
+    - net: bridge: mcast: wait for previous gc cycles when removing port
+    - net: linkwatch: use system_unbound_wq
+    - Bluetooth: l2cap: always unlock channel in l2cap_conless_channel()
+    - net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register()
+    - l2tp: fix lockdep splat
+    - net: fec: Stop PPS on driver remove
+    - rcutorture: Fix rcu_torture_fwd_cb_cr() data race
+    - md: do not delete safemode_timer in mddev_suspend
+    - md/raid5: avoid BUG_ON() while continue reshape after reassembling
+    - clocksource/drivers/sh_cmt: Address race condition for clock events
+    - ACPI: battery: create alarm sysfs attribute atomically
+    - ACPI: SBS: manage alarm sysfs attribute through psy core
+    - selftests/bpf: Fix send_signal test with nested CONFIG_PARAVIRT
+    - PCI: Add Edimax Vendor ID to pci_ids.h
+    - udf: prevent integer overflow in udf_bitmap_free_blocks()
+    - wifi: nl80211: don't give key data to userspace
+    - btrfs: fix bitmap leak when loading free space cache on duplicate entry
+    - drm/amdgpu/pm: Fix the null pointer dereference for smu7
+    - drm/amdgpu: Fix the null pointer dereference to ras_manager
+    - drm/amdgpu/pm: Fix the null pointer dereference in apply_state_adjust_rules
+    - drm/amd/display: Add null checker before passing variables
+    - media: uvcvideo: Ignore empty TS packets
+    - media: uvcvideo: Fix the bandwdith quirk on USB 3.x
+    - ext4: fix uninitialized variable in ext4_inlinedir_to_tree
+    - jbd2: avoid memleak in jbd2_journal_write_metadata_buffer
+    - s390/sclp: Prevent release of buffer in I/O
+    - SUNRPC: Fix a race to wake a sync task
+    - profiling: remove profile=sleep support
+    - scsi: mpt3sas: Avoid IOMMU page faults on REPORT ZONES
+    - sched/cputime: Fix mul_u64_u64_div_u64() precision for cputime
+    - ext4: fix wrong unit use in ext4_mb_find_by_goal
+    - arm64: cpufeature: Force HWCAP to be based on the sysreg visible to user-
+      space
+    - arm64: Add Neoverse-V2 part
+    - arm64: barrier: Restore spec_bar() macro
+    - arm64: cputype: Add Cortex-X4 definitions
+    - arm64: cputype: Add Neoverse-V3 definitions
+    - arm64: errata: Add workaround for Arm errata 3194386 and 3312417
+    - [Config] Set ARM64_ERRATUM_3194386=y
+    - arm64: cputype: Add Cortex-X3 definitions
+    - arm64: cputype: Add Cortex-A720 definitions
+    - arm64: cputype: Add Cortex-X925 definitions
+    - arm64: errata: Unify speculative SSBS errata logic
+    - arm64: errata: Expand speculative SSBS workaround
+    - arm64: cputype: Add Cortex-X1C definitions
+    - arm64: cputype: Add Cortex-A725 definitions
+    - arm64: errata: Expand speculative SSBS workaround (again)
+    - i2c: smbus: Improve handling of stuck alerts
+    - ASoC: codecs: wcd938x-sdw: Correct Soundwire ports mask
+    - ASoC: codecs: wsa881x: Correct Soundwire ports mask
+    - spi: spidev: Add missing spi_device_id for bh2228fv
+    - i2c: smbus: Send alert notifications to all devices if source not found
+    - bpf: kprobe: remove unused declaring of bpf_kprobe_override
+    - kprobes: Fix to check symbol prefixes correctly
+    - spi: spi-fsl-lpspi: Fix scldiv calculation
+    - ALSA: usb-audio: Re-add ScratchAmp quirk entries
+    - ASoC: meson: axg-fifo: fix irq scheduling issue with PREEMPT_RT
+    - drm/client: fix null pointer dereference in drm_client_modeset_probe
+    - ALSA: line6: Fix racy access to midibuf
+    - ALSA: hda: Add HP MP9 G4 Retail System AMS to force connect list
+    - ALSA: hda/hdmi: Yet more pin fix for HP EliteDesk 800 G4
+    - usb: vhci-hcd: Do not drop references before new references are gained
+    - USB: serial: debug: do not echo input by default
+    - usb: gadget: core: Check for unset descriptor
+    - usb: gadget: u_serial: Set start_delayed during suspend
+    - scsi: mpi3mr: Avoid IOMMU page faults on REPORT ZONES
+    - scsi: ufs: core: Fix hba->last_dme_cmd_tstamp timestamp updating logic
+    - tick/broadcast: Move per CPU pointer access into the atomic section
+    - vhost-vdpa: switch to use vmf_insert_pfn() in the fault handler
+    - ntp: Clamp maxerror and esterror to operating range
+    - clocksource: Reduce the default clocksource_watchdog() retries to 2
+    - torture: Enable clocksource watchdog with "tsc=watchdog"
+    - clocksource: Scale the watchdog read retries automatically
+    - clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()
+    - irqchip/meson-gpio: support more than 8 channels gpio irq
+    - irqchip/meson-gpio: Convert meson_gpio_irq_controller::lock to
+      'raw_spinlock_t'
+    - driver core: Fix uevent_show() vs driver detach race
+    - ntp: Safeguard against time_constant overflow
+    - timekeeping: Fix bogus clock_was_set() invocation in do_adjtimex()
+    - serial: core: check uartclk for zero to avoid divide by zero
+    - kcov: properly check for softirq context
+    - irqchip/xilinx: Fix shift out of bounds
+    - genirq/irqdesc: Honor caller provided affinity in alloc_desc()
+    - power: supply: axp288_charger: Fix constant_charge_voltage writes
+    - power: supply: axp288_charger: Round constant_charge_voltage writes down
+    - tracing: Fix overflow in get_free_elt()
+    - padata: Fix possible divide-by-0 panic in padata_mt_helper()
+    - x86/mtrr: Check if fixed MTRRs exist before saving them
+    - sched/smt: Introduce sched_smt_present_inc/dec() helper
+    - sched/smt: Fix unbalance sched_smt_present dec/inc
+    - drm/bridge: analogix_dp: properly handle zero sized AUX transactions
+    - drm/mgag200: Set DDC timeout in milliseconds
+    - mptcp: sched: check both directions for backup
+    - mptcp: distinguish rcv vs sent backup flag in requests
+    - mptcp: fix NL PM announced address accounting
+    - mptcp: mib: count MPJ with backup flag
+    - mptcp: fix bad RCVPRUNED mib accounting
+    - mptcp: pm: only set request_bkup flag when sending MP_PRIO
+    - mptcp: export local_address
+    - mptcp: pm: fix backup support in signal endpoints
+    - selftests: mptcp: join: validate backup in MPJ
+    - selftests: mptcp: join: check backup support in signal endp
+    - btrfs: fix corruption after buffer fault in during direct IO append write
+    - xfs: fix log recovery buffer allocation for the legacy h_size fixup
+    - btrfs: fix double inode unlock for direct IO sync writes
+    - PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal
+    - netfilter: nf_tables: set element extended ACK reporting support
+    - netfilter: nf_tables: bail out if stateful expression provides no .clone
+    - netfilter: nf_tables: allow clone callbacks to sleep
+    - netfilter: nf_tables: prefer nft_chain_validate
+    - net: stmmac: Enable mac_managed_pm phylink config
+    - PCI: dwc: Restore MSI Receiver mask during resume
+    - wifi: mac80211: check basic rates validity
+    - mptcp: fully established after ADD_ADDR echo on MPJ
+    - drm/i915/gem: Fix Virtual Memory mapping boundaries calculation
+    - powerpc: Avoid nmi_enter/nmi_exit in real mode interrupt.
+    - arm64: dts: qcom: msm8996: correct #clock-cells for QMP PHY nodes
+    - arm64: cpufeature: Fix the visibility of compat hwcaps
+    - exec: Fix ToCToU between perm check and set-uid/gid usage
+    - nvme/pci: Add APST quirk for Lenovo N60z laptop
+    - usb: gadget: u_audio: Check return codes from usb_ep_enable and
+      config_ep_by_speed.
+    - binfmt_flat: Fix corruption when not offsetting data start
+    - wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values
+    - ARM: dts: imx6qdl-kontron-samx6i: fix phy-mode
+    - media: Revert "media: dvb-usb: Fix unexpected infinite loop in
+      dvb_usb_read_remote_control()"
+    - Revert "ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error"
+    - Linux 5.15.165
+
+  * CVE-2024-26661
+    - drm/amd/display: Add NULL test for 'timing generator' in 'dcn21_set_pipe()'
+
+  * CVE-2024-25744
+    - x86: Fix misspelled Kconfig symbols
+    - x86: Introduce ia32_enabled()
+    - x86/sev: Rename mem_encrypt.c to mem_encrypt_amd.c
+    - x86/coco: Disable 32-bit emulation by default on TDX and SEV
+    - x86/entry: Convert INT 0x80 emulation to IDTENTRY
+    - x86/entry: Do not allow external 0x80 interrupts
+    - x86/entry: Add do_SYSENTER_32() prototype
+    - x86/bhi: Add support for clearing branch history at syscall entry
+
+  * [UBUNTU 22.04] s390/cpum_cf: make crypto counters upward compatible
+    (LP: #2074380)
+    - s390/cpum_cf: make crypto counters upward compatible across machine types
+
+  * Jammy update: v5.15.164 upstream stable release (LP: #2076100)
+    - gcc-plugins: Rename last_stmt() for GCC 14+
+    - filelock: Remove locks reliably when fcntl/close race is detected
+    - ARM: 9324/1: fix get_user() broken with veneer
+    - ACPI: processor_idle: Fix invalid comparison with insertion sort for latency
+    - scsi: core: Fix a use-after-free
+    - scsi: core: alua: I/O errors for ALUA state transitions
+    - scsi: qedf: Don't process stag work during unload and recovery
+    - scsi: qedf: Wait for stag work during unload
+    - scsi: qedf: Set qed_slowpath_params to zero before use
+    - ACPI: EC: Abort address space access upon error
+    - ACPI: EC: Avoid returning AE_OK on errors in address space handler
+    - tools/power/cpupower: Fix Pstate frequency reporting on AMD Family 1Ah CPUs
+    - wifi: mac80211: mesh: init nonpeer_pm to active by default in mesh sdata
+    - wifi: mac80211: handle tasklet frames before stopping
+    - wifi: iwlwifi: mvm: d3: fix WoWLAN command version lookup
+    - wifi: iwlwifi: mvm: Handle BIGTK cipher in kek_kck cmd
+    - wifi: iwlwifi: mvm: properly set 6 GHz channel direct probe option
+    - wifi: mac80211: fix UBSAN noise in ieee80211_prep_hw_scan()
+    - selftests/openat2: Fix build warnings on ppc64
+    - Input: silead - Always support 10 fingers
+    - net: ipv6: rpl_iptunnel: block BH in rpl_output() and rpl_input()
+    - ila: block BH in ila_output()
+    - arm64: armv8_deprecated: Fix warning in isndep cpuhp starting process
+    - null_blk: fix validation of block size
+    - kconfig: gconf: give a proper initial state to the Save button
+    - kconfig: remove wrong expr_trans_bool()
+    - fs/file: fix the check in find_next_fd()
+    - mei: demote client disconnect warning on suspend to debug
+    - nvme: avoid double free special payload
+    - wifi: cfg80211: wext: add extra SIOCSIWSCAN data check
+    - KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group()
+    - drm/vmwgfx: Fix missing HYPERVISOR_GUEST dependency
+    - ALSA: hda/realtek: Add more codec ID to no shutup pins list
+    - mips: fix compat_sys_lseek syscall
+    - Input: elantech - fix touchpad state on resume for Lenovo N24
+    - Input: i8042 - add Ayaneo Kun to i8042 quirk table
+    - bytcr_rt5640 : inverse jack detect for Archos 101 cesium
+    - ALSA: dmaengine: Synchronize dma channel after drop()
+    - ASoC: ti: davinci-mcasp: Set min period size using FIFO config
+    - ASoC: ti: omap-hdmi: Fix too long driver name
+    - can: kvaser_usb: fix return value for hif_usb_send_regout
+    - s390/sclp: Fix sclp_init() cleanup on failure
+    - platform/x86: wireless-hotkey: Add support for LG Airplane Button
+    - platform/x86: lg-laptop: Remove LGEX0815 hotkey handling
+    - platform/x86: lg-laptop: Change ACPI device id
+    - platform/x86: lg-laptop: Use ACPI device handle when evaluating WMAB/WMBB
+    - btrfs: qgroup: fix quota root leak after quota disable failure
+    - ALSA: hda/relatek: Enable Mute LED on HP Laptop 15-gw0xxx
+    - ALSA: dmaengine_pcm: terminate dmaengine before synchronize
+    - net: usb: qmi_wwan: add Telit FN912 compositions
+    - net: mac802154: Fix racy device stats updates by DEV_STATS_INC() and
+      DEV_STATS_ADD()
+    - powerpc/pseries: Whitelist dtl slub object for copying to userspace
+    - powerpc/eeh: avoid possible crash when edev->pdev changes
+    - scsi: libsas: Fix exp-attached device scan after probe failure scanned in
+      again after probe failed
+    - Bluetooth: hci_core: cancel all works upon hci_unregister_dev()
+    - drm/radeon: check bo_va->bo is non-NULL before using it
+    - fs: better handle deep ancestor chains in is_subdir()
+    - riscv: stacktrace: fix usage of ftrace_graph_ret_addr()
+    - spi: imx: Don't expect DMA for i.MX{25,35,50,51,53} cspi devices
+    - selftests/vDSO: fix clang build errors and warnings
+    - hfsplus: fix uninit-value in copy_name
+    - spi: mux: set ctlr->bits_per_word_mask
+    - tracing: Define the is_signed_type() macro once
+    - minmax: sanity check constant bounds when clamping
+    - minmax: clamp more efficiently by avoiding extra comparison
+    - minmax: fix header inclusions
+    - minmax: allow min()/max()/clamp() if the arguments have the same signedness.
+    - minmax: allow comparisons of 'int' against 'unsigned char/short'
+    - minmax: relax check to allow comparison between unsigned arguments and
+      signed constants
+    - mm/damon/core: merge regions aggressively when max_nr_regions is unmet
+    - wifi: mac80211: disable softirqs for queued frame handling
+    - drm/amdgpu: Fix signedness bug in sdma_v4_0_process_trap_irq()
+    - samples: Add fs error monitoring example
+    - samples: Make fs-monitor depend on libc and headers
+    - docs: Fix formatting of literal sections in fanotify docs
+    - Add gitignore file for samples/fanotify/ subdirectory
+    - net: relax socket state check at accept time.
+    - ocfs2: add bounds checking to ocfs2_check_dir_entry()
+    - jfs: don't walk off the end of ealist
+    - fs/ntfs3: Validate ff offset
+    - ALSA: hda/realtek: Enable headset mic on Positivo SU C1400
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
+    - arm64: dts: qcom: msm8996: Disable SS instance in Parkmode for USB
+    - arm64: dts: qcom: sdm630: Disable SS instance in Parkmode for USB
+    - ALSA: pcm_dmaengine: Don't synchronize DMA channel when DMA is paused
+    - filelock: Fix fcntl/close race recovery compat path
+    - wifi: rt2x00: use explicitly signed or unsigned types
+    - tun: add missing verification for short frame
+    - tap: add missing verification for short frame
+    - Linux 5.15.164
+
+  * Jammy update: v5.15.166 upstream stable release (LP: #2080594) //
+    CVE-2024-45016
+    - netem: fix return value if duplicate enqueue fails
+
+  * CVE-2024-38630
+    - watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
+
+  * CVE-2024-27397
+    - netfilter: nf_tables: use timestamp to check for set element timeout
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 27 Sep 2024 14:49:00 +0200
+
+linux (5.15.0-122.132) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-122.132 -proposed tracker (LP: #2078154)
+
+  * isolcpus are ignored when using cgroups V2, causing processes to have wrong
+    affinity (LP: #2076957)
+    - cgroup/cpuset: Optimize cpuset_attach() on v2
+
+  * Jammy update: v5.15.164 upstream stable release (LP: #2076100) //
+    CVE-2024-41009
+    - bpf: Fix overrunning reservations in ringbuf
+
+  * CVE-2024-39494
+    - ima: Fix use-after-free on a dentry's dname.name
+
+  * CVE-2024-39496
+    - btrfs: zoned: fix use-after-free due to race with dev replace
+
+  * CVE-2024-42160
+    - f2fs: check validation of fault attrs in f2fs_build_fault_attr()
+    - f2fs: Add inline to f2fs_build_fault_attr() stub
+
+  * CVE-2024-38570
+    - gfs2: Rename sd_{ glock => kill }_wait
+    - gfs2: Fix potential glock use-after-free on unmount
+
+  * CVE-2024-42228
+    - drm/amdgpu: Using uninitialized value *size when calling amdgpu_vce_cs_reloc
+
+  * CVE-2024-27012
+    - netfilter: nf_tables: restore set elements when delete set fails
+
+  * CVE-2024-26677
+    - rxrpc: Fix delayed ACKs to not set the reference serial number
+
+ -- Manuel Diewald <manuel.diewald@canonical.com>  Thu, 29 Aug 2024 14:23:02 +0200
+
+linux (5.15.0-121.131) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-121.131 -proposed tracker (LP: #2076347)
+
+  * jammy:linux bpf selftest do not build (LP: #2076334)
+    - SAUCE: Revert "bpf: Allow reads from uninit stack"
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Fri, 09 Aug 2024 10:15:16 +0200
+
+linux (5.15.0-120.130) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-120.130 -proposed tracker (LP: #2075903)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2024.08.05)
+
+  * Jammy update: v5.15.163 upstream stable release (LP: #2075170)
+    - Compiler Attributes: Add __uninitialized macro
+    - locking/mutex: Introduce devm_mutex_init()
+    - drm/lima: fix shared irq handling on driver remove
+    - media: dvb: as102-fe: Fix as10x_register_addr packing
+    - media: dvb-usb: dib0700_devices: Add missing release_firmware()
+    - IB/core: Implement a limit on UMAD receive List
+    - scsi: qedf: Make qedf_execute_tmf() non-preemptible
+    - crypto: aead,cipher - zeroize key buffer after use
+    - drm/amdgpu: Initialize timestamp for some legacy SOCs
+    - drm/amd/display: Check index msg_id before read or write
+    - drm/amd/display: Check pipe offset before setting vblank
+    - drm/amd/display: Skip finding free audio for unknown engine_id
+    - media: dw2102: Don't translate i2c read into write
+    - sctp: prefer struct_size over open coded arithmetic
+    - firmware: dmi: Stop decoding on broken entry
+    - Input: ff-core - prefer struct_size over open coded arithmetic
+    - wifi: mt76: replace skb_put with skb_put_zero
+    - net: dsa: mv88e6xxx: Correct check for empty list
+    - media: dvb-frontends: tda18271c2dd: Remove casting during div
+    - media: s2255: Use refcount_t instead of atomic_t for num_channels
+    - media: dvb-frontends: tda10048: Fix integer overflow
+    - i2c: i801: Annotate apanel_addr as __ro_after_init
+    - powerpc/64: Set _IO_BASE to POISON_POINTER_DELTA not 0 for CONFIG_PCI=n
+    - orangefs: fix out-of-bounds fsid access
+    - kunit: Fix timeout message
+    - powerpc/xmon: Check cpu id in commands "c#", "dp#" and "dx#"
+    - igc: fix a log entry using uninitialized netdev
+    - bpf: Avoid uninitialized value in BPF_CORE_READ_BITFIELD
+    - jffs2: Fix potential illegal address access in jffs2_free_inode
+    - s390/pkey: Wipe sensitive data on failure
+    - tools/power turbostat: Remember global max_die_id
+    - UPSTREAM: tcp: fix DSACK undo in fast recovery to call tcp_try_to_open()
+    - tcp_metrics: validate source addr length
+    - KVM: s390: fix LPSWEY handling
+    - e1000e: Fix S0ix residency on corporate systems
+    - net: allow skb_datagram_iter to be called from any context
+    - wifi: wilc1000: fix ies_len type in connect path
+    - riscv: kexec: Avoid deadlock in kexec crash path
+    - netfilter: nf_tables: unconditionally flush pending work before notifier
+    - bonding: Fix out-of-bounds read in bond_option_arp_ip_targets_set()
+    - selftests: fix OOM in msg_zerocopy selftest
+    - selftests: make order checking verbose in msg_zerocopy selftest
+    - inet_diag: Initialize pad field in struct inet_diag_req_v2
+    - gpiolib: of: factor out code overriding gpio line polarity
+    - gpiolib: of: add a quirk for reset line polarity for Himax LCDs
+    - gpiolib: of: add polarity quirk for TSC2005
+    - Revert "igc: fix a log entry using uninitialized netdev"
+    - nilfs2: fix inode number range checks
+    - nilfs2: add missing check for inode numbers on directory entries
+    - mm: optimize the redundant loop of mm_update_owner_next()
+    - mm: avoid overflows in dirty throttling logic
+    - btrfs: fix adding block group to a reclaim list and the unused list during
+      reclaim
+    - Bluetooth: qca: Fix BT enable failure again for QCA6390 after warm reboot
+    - can: kvaser_usb: Explicitly initialize family in leafimx driver_info struct
+    - fsnotify: Do not generate events for O_PATH file descriptors
+    - Revert "mm/writeback: fix possible divide-by-zero in wb_dirty_limits(),
+      again"
+    - drm/nouveau: fix null pointer dereference in nouveau_connector_get_modes
+    - drm/amdgpu/atomfirmware: silence UBSAN warning
+    - mtd: rawnand: Ensure ECC configuration is propagated to upper layers
+    - mtd: rawnand: Bypass a couple of sanity checks during NAND identification
+    - mtd: rawnand: rockchip: ensure NVDDR timings are rejected
+    - ima: Avoid blocking in RCU read-side critical section
+    - media: dw2102: fix a potential buffer overflow
+    - clk: qcom: gcc-sm6350: Fix gpll6* & gpll7 parents
+    - i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr
+    - fs/ntfs3: Mark volume as dirty if xattr is broken
+    - ALSA: hda/realtek: Enable headset mic of JP-IK LEAP W502 with ALC897
+    - nvme-multipath: find NUMA path only for online numa-node
+    - dma-mapping: benchmark: avoid needless copy_to_user if benchmark fails
+    - nvme: adjust multiples of NVME_CTRL_PAGE_SIZE in offset
+    - regmap-i2c: Subtract reg size from max_write
+    - platform/x86: touchscreen_dmi: Add info for GlobalSpace SolT IVW 11.6"
+      tablet
+    - platform/x86: touchscreen_dmi: Add info for the EZpad 6s Pro
+    - nvmet: fix a possible leak when destroy a ctrl during qp establishment
+    - kbuild: fix short log for AS in link-vmlinux.sh
+    - nfc/nci: Add the inconsistency check between the input data length and count
+    - null_blk: Do not allow runt zone with zone capacity smaller then zone size
+    - nilfs2: fix incorrect inode allocation from reserved inodes
+    - mm: prevent derefencing NULL ptr in pfn_section_valid()
+    - filelock: fix potential use-after-free in posix_lock_inode
+    - fs/dcache: Re-use value stored to dentry->d_flags instead of re-reading
+    - vfs: don't mod negative dentry count when on shrinker list
+    - tcp: fix incorrect undo caused by DSACK of TLP retransmit
+    - skmsg: Skip zero length skb in sk_msg_recvmsg
+    - octeontx2-af: Fix incorrect value output on error path in
+      rvu_check_rsrc_availability()
+    - net: fix rc7's __skb_datagram_iter()
+    - i40e: Fix XDP program unloading while removing the driver
+    - net: lantiq_etop: add blank line after declaration
+    - net: ethernet: lantiq_etop: fix double free in detach
+    - net: ethernet: mtk-star-emac: set mac_managed_pm when probing
+    - ppp: reject claimed-as-LCP but actually malformed packets
+    - ethtool: netlink: do not return SQI value if link is down
+    - udp: Set SOCK_RCU_FREE earlier in udp_lib_get_port().
+    - s390: Mark psw in __load_psw_mask() as __unitialized
+    - ARM: davinci: Convert comma to semicolon
+    - octeontx2-af: replace cpt slot with lf id on reg write
+    - octeontx2-af: update cpt lf alloc mailbox
+    - octeontx2-af: fix a issue with cpt_lf_alloc mailbox
+    - octeontx2-af: fix detection of IP layer
+    - octeontx2-af: extend RSS supported offload types
+    - octeontx2-af: fix issue with IPv6 ext match for RSS
+    - octeontx2-af: fix issue with IPv4 match for RSS
+    - tcp: use signed arithmetic in tcp_rtx_probe0_timed_out()
+    - tcp: avoid too many retransmit packets
+    - net: ks8851: Fix potential TX stall after interface reopen
+    - USB: serial: option: add Telit generic core-dump composition
+    - USB: serial: option: add Telit FN912 rmnet compositions
+    - USB: serial: option: add Fibocom FM350-GL
+    - USB: serial: option: add support for Foxconn T99W651
+    - USB: serial: option: add Netprisma LCUK54 series modules
+    - USB: serial: option: add Rolling RW350-GL variants
+    - USB: serial: mos7840: fix crash on resume
+    - USB: Add USB_QUIRK_NO_SET_INTF quirk for START BP-850k
+    - usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()
+    - USB: core: Fix duplicate endpoint bug by clearing reserved bits in the
+      descriptor
+    - hpet: Support 32-bit userspace
+    - nvmem: rmem: Fix return value of rmem_read()
+    - nvmem: meson-efuse: Fix return value of nvmem callbacks
+    - nvmem: core: only change name to fram for current attribute
+    - ALSA: hda/realtek: add quirk for Clevo V5[46]0TU
+    - ALSA: hda/realtek: Enable Mute LED on HP 250 G7
+    - ALSA: hda/realtek: Limit mic boost on VAIO PRO PX
+    - Fix userfaultfd_api to return EINVAL as expected
+    - libceph: fix race between delayed_work() and ceph_monc_stop()
+    - wireguard: allowedips: avoid unaligned 64-bit memory accesses
+    - wireguard: queueing: annotate intentional data race in cpu round robin
+    - wireguard: send: annotate intentional data race in checking empty queue
+    - ipv6: annotate data-races around cnf.disable_ipv6
+    - bpf: Allow reads from uninit stack
+    - nilfs2: fix kernel bug on rename operation of broken directory
+    - i2c: rcar: bring hardware to known state when probing
+    - i2c: mark HostNotify target address as used
+    - i2c: rcar: Add R-Car Gen4 support
+    - i2c: rcar: reset controller is mandatory for Gen3+
+    - i2c: rcar: introduce Gen4 devices
+    - i2c: rcar: ensure Gen3+ reset does not disturb local targets
+    - i2c: testunit: avoid re-issued work after read message
+    - i2c: rcar: clear NO_RXDMA flag after resetting
+    - x86/entry/64: Remove obsolete comment on tracing vs. SYSRET
+    - x86/bhi: Avoid warning in #DB handler due to BHI mitigation
+    - kbuild: Make ld-version.sh more robust against version string changes
+    - i2c: rcar: fix error code in probe()
+    - Linux 5.15.163
+
+  * [SRU] UBSAN warnings in bnx2x kernel driver (LP: #2074215) // Jammy update:
+    v5.15.163 upstream stable release (LP: #2075170)
+    - bnx2x: Fix multiple UBSAN array-index-out-of-bounds
+
+  * Jammy update: v5.15.162 upstream stable release (LP: #2073765)
+    - mmc: davinci_mmc: Convert to platform remove callback returning void
+    - wifi: mac80211: mesh: Fix leak of mesh_preq_queue objects
+    - wifi: mac80211: Fix deadlock in ieee80211_sta_ps_deliver_wakeup()
+    - wifi: cfg80211: Lock wiphy in cfg80211_get_station
+    - wifi: cfg80211: pmsr: use correct nla_get_uX functions
+    - wifi: iwlwifi: mvm: revert gen2 TX A-MPDU size to 64
+    - wifi: iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
+    - wifi: iwlwifi: mvm: check n_ssids before accessing the ssids
+    - wifi: iwlwifi: mvm: don't read past the mfuart notifcation
+    - wifi: mac80211: correctly parse Spatial Reuse Parameter Set element
+    - net/ncsi: Simplify Kconfig/dts control flow
+    - net/ncsi: Fix the multi thread manner of NCSI driver
+    - ipv6: sr: block BH in seg6_output_core() and seg6_input_core()
+    - bpf: Set run context for rawtp test_run callback
+    - octeontx2-af: Always allocate PF entries from low prioriy zone
+    - net: sched: sch_multiq: fix possible OOB write in multiq_tune()
+    - vxlan: Fix regression when dropping packets due to invalid src addresses
+    - tcp: count CLOSE-WAIT sockets for TCP_MIB_CURRESTAB
+    - net/sched: taprio: always validate TCA_TAPRIO_ATTR_PRIOMAP
+    - ptp: Fix error message on failed pin verification
+    - af_unix: Set sk->sk_state under unix_state_lock() for truly disconencted
+      peer.
+    - af_unix: Annodate data-races around sk->sk_state for writers.
+    - af_unix: Annotate data-race of sk->sk_state in unix_inq_len().
+    - af_unix: Annotate data-races around sk->sk_state in unix_write_space() and
+      poll().
+    - net: inline sock_prot_inuse_add()
+    - net: drop nopreempt requirement on sock_prot_inuse_add()
+    - af_unix: Annotate data-race of sk->sk_state in unix_stream_connect().
+    - af_unix: Annotate data-races around sk->sk_state in sendmsg() and recvmsg().
+    - af_unix: Annotate data-race of sk->sk_state in unix_stream_read_skb().
+    - af_unix: Annotate data-races around sk->sk_state in UNIX_DIAG.
+    - af_unix: Annotate data-race of net->unx.sysctl_max_dgram_qlen.
+    - af_unix: Use unix_recvq_full_lockless() in unix_stream_connect().
+    - af_unix: annotate lockless accesses to sk->sk_err
+    - af_unix: Use skb_queue_empty_lockless() in unix_release_sock().
+    - af_unix: Use skb_queue_len_lockless() in sk_diag_show_rqlen().
+    - af_unix: Annotate data-race of sk->sk_shutdown in sk_diag_fill().
+    - ipv6: fix possible race in __fib6_drop_pcpu_from()
+    - usb: gadget: f_fs: use io_data->status consistently
+    - usb: gadget: f_fs: Fix race between aio_cancel() and AIO request complete
+    - iio: accel: mxc4005: Reset chip on probe() and resume()
+    - drm/amd/display: Handle Y carry-over in VCP X.Y calculation
+    - drm/amd/display: Clean up some inconsistent indenting
+    - drm/amd/display: drop unnecessary NULL checks in debugfs
+    - drm/amd/display: Fix incorrect DSC instance for MST
+    - pvpanic: Keep single style across modules
+    - pvpanic: Indentation fixes here and there
+    - misc/pvpanic: deduplicate common code
+    - misc/pvpanic-pci: register attributes via pci_driver
+    - skbuff: introduce skb_pull_data
+    - Bluetooth: hci_qca: mark OF related data as maybe unused
+    - Bluetooth: btqca: use le32_to_cpu for ver.soc_id
+    - Bluetooth: btqca: Add WCN3988 support
+    - Bluetooth: qca: use switch case for soc type behavior
+    - Bluetooth: qca: add support for QCA2066
+    - Bluetooth: qca: fix info leak when fetching fw build id
+    - serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
+    - serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
+    - x86/ibt,ftrace: Search for __fentry__ location
+    - ftrace: Fix possible use-after-free issue in ftrace_location()
+    - i2c: add fwnode APIs
+    - i2c: acpi: Unbind mux adapters before delete
+    - cma: factor out minimum alignment requirement
+    - mm/cma: drop incorrect alignment check in cma_init_reserved_mem
+    - selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
+    - selftests/mm: conform test to TAP format output
+    - selftests/mm: compaction_test: fix bogus test success on Aarch64
+    - wifi: ath10k: fix QCOM_RPROC_COMMON dependency
+    - btrfs: fix leak of qgroup extent records after transaction abort
+    - nilfs2: Remove check for PageError
+    - nilfs2: return the mapped address from nilfs_get_page()
+    - nilfs2: fix nilfs_empty_dir() misjudgment and long loop on I/O errors
+    - USB: class: cdc-wdm: Fix CPU lockup caused by excessive log messages
+    - usb: typec: tcpm: Ignore received Hard Reset in TOGGLING state
+    - mei: me: release irq in mei_me_pci_resume error path
+    - jfs: xattr: fix buffer overflow for invalid xattr
+    - xhci: Set correct transferred length for cancelled bulk transfers
+    - xhci: Apply reset resume quirk to Etron EJ188 xHCI host
+    - xhci: Handle TD clearing for multiple streams case
+    - xhci: Apply broken streams quirk to Etron EJ188 xHCI host
+    - scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
+    - powerpc/uaccess: Fix build errors seen with GCC 13/14
+    - Input: try trimming too long modalias strings
+    - clk: sifive: Do not register clkdevs for PRCI clocks
+    - SUNRPC: return proper error from gss_wrap_req_priv
+    - platform/x86: dell-smbios-base: Use sysfs_emit()
+    - platform/x86: dell-smbios: Fix wrong token data in sysfs
+    - gpio: tqmx86: fix typo in Kconfig label
+    - gpio: tqmx86: store IRQ trigger type and unmask status separately
+    - HID: core: remove unnecessary WARN_ON() in implement()
+    - iommu/amd: Introduce pci segment structure
+    - iommu/amd: Fix sysfs leak in iommu init
+    - iommu: Return right value in iommu_sva_bind_device()
+    - HID: logitech-dj: Fix memory leak in logi_dj_recv_switch_to_dj_mode()
+    - drm/vmwgfx: 3D disabled should not effect STDU memory limits
+    - net: sfp: Always call `sfp_sm_mod_remove()` on remove
+    - net: hns3: fix kernel crash problem in concurrent scenario
+    - net: hns3: add cond_resched() to hns3 ring buffer init process
+    - liquidio: Adjust a NULL pointer handling path in lio_vf_rep_copy_packet
+    - drm/komeda: check for error-valued pointer
+    - drm/bridge/panel: Fix runtime warning on panel bridge release
+    - tcp: fix race in tcp_v6_syn_recv_sock()
+    - net/mlx5e: Fix features validation check for tunneled UDP (non-VXLAN)
+      packets
+    - netfilter: ipset: Fix race between namespace cleanup and gc in the list:set
+      type
+    - net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs
+      parameters
+    - net/ipv6: Fix the RT cache flush via sysctl using a previous delay
+    - ionic: fix use after netif_napi_del()
+    - af_unix: Read with MSG_PEEK loops if the first unread byte is OOB
+    - iio: adc: ad9467: fix scan type sign
+    - iio: dac: ad5592r: fix temperature channel scaling value
+    - iio: imu: inv_icm42600: delete unneeded update watermark call
+    - drivers: core: synchronize really_probe() and dev_uevent()
+    - drm/exynos/vidi: fix memory leak in .get_modes()
+    - drm/exynos: hdmi: report safe 640x480 mode as a fallback when no EDID found
+    - mptcp: ensure snd_una is properly initialized on connect
+    - tracing/selftests: Fix kprobe event name test for .isra. functions
+    - null_blk: Print correct max open zones limit in null_init_zoned_dev()
+    - sock_map: avoid race between sock_map_close and sk_psock_put
+    - vmci: prevent speculation leaks by sanitizing event in event_deliver()
+    - spmi: hisi-spmi-controller: Do not override device identifier
+    - knfsd: LOOKUP can return an illegal error value
+    - fs/proc: fix softlockup in __read_vmcore
+    - ocfs2: use coarse time for new created files
+    - ocfs2: fix races between hole punching and AIO+DIO
+    - PCI: rockchip-ep: Remove wrong mask on subsys_vendor_id
+    - dmaengine: axi-dmac: fix possible race in remove()
+    - intel_th: pci: Add Granite Rapids support
+    - intel_th: pci: Add Granite Rapids SOC support
+    - intel_th: pci: Add Sapphire Rapids SOC support
+    - intel_th: pci: Add Meteor Lake-S support
+    - intel_th: pci: Add Lunar Lake support
+    - nilfs2: fix potential kernel bug due to lack of writeback flag waiting
+    - tick/nohz_full: Don't abuse smp_call_function_single() in
+      tick_setup_device()
+    - scsi: mpi3mr: Fix ATA NCQ priority support
+    - mm/huge_memory: don't unpoison huge_zero_folio
+    - serial: 8250_pxa: Configure tx_loadsz to match FIFO IRQ level
+    - hugetlb_encode.h: fix undefined behaviour (34 << 26)
+    - mptcp: pm: inc RmAddr MIB counter once per RM_ADDR ID
+    - mptcp: pm: update add_addr counters after connect
+    - kbuild: Remove support for Clang's ThinLTO caching
+    - greybus: Fix use-after-free bug in gb_interface_release due to race
+      condition.
+    - usb-storage: alauda: Check whether the media is initialized
+    - i2c: at91: Fix the functionality flags of the slave-only interface
+    - i2c: designware: Fix the functionality flags of the slave-only interface
+    - zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
+    - Bluetooth: qca: Fix error code in qca_read_fw_build_info()
+    - Bluetooth: qca: fix info leak when fetching board id
+    - padata: Disable BH when taking works lock on MT path
+    - crypto: hisilicon/sec - Fix memory leak for sec resource release
+    - rcutorture: Fix rcu_torture_one_read() pipe_count overflow comment
+    - rcutorture: Make stall-tasks directly exit when rcutorture tests end
+    - rcutorture: Fix invalid context warning when enable srcu barrier testing
+    - block/ioctl: prefer different overflow check
+    - selftests/bpf: Prevent client connect before server bind in
+      test_tc_tunnel.sh
+    - selftests/bpf: Fix flaky test btf_map_in_map/lookup_update
+    - batman-adv: bypass empty buckets in batadv_purge_orig_ref()
+    - wifi: ath9k: work around memset overflow warning
+    - af_packet: avoid a false positive warning in packet_setsockopt()
+    - drop_monitor: replace spin_lock by raw_spin_lock
+    - scsi: qedi: Fix crash while reading debugfs attribute
+    - kselftest: arm64: Add a null pointer check
+    - netpoll: Fix race condition in netpoll_owner_active
+    - HID: Add quirk for Logitech Casa touchpad
+    - ACPI: video: Add backlight=native quirk for Lenovo Slim 7 16ARH7
+    - Bluetooth: ath3k: Fix multiple issues reported by checkpatch.pl
+    - drm/amd/display: Exit idle optimizations before HDCP execution
+    - drm/lima: add mask irq callback to gp and pp
+    - drm/lima: mask irqs in timeout path before hard reset
+    - powerpc/pseries: Enforce hcall result buffer validity and size
+    - powerpc/io: Avoid clang null pointer arithmetic warnings
+    - power: supply: cros_usbpd: provide ID table for avoiding fallback match
+    - iommu/arm-smmu-v3: Free MSIs in case of ENOMEM
+    - f2fs: remove clear SB_INLINECRYPT flag in default_options
+    - usb: misc: uss720: check for incompatible versions of the Belkin F5U002
+    - Avoid hw_desc array overrun in dw-axi-dmac
+    - udf: udftime: prevent overflow in udf_disk_stamp_to_time()
+    - PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports
+    - MIPS: Octeon: Add PCIe link status check
+    - serial: imx: Introduce timeout when waiting on transmitter empty
+    - serial: exar: adding missing CTI and Exar PCI ids
+    - MIPS: Routerboard 532: Fix vendor retry check code
+    - mips: bmips: BCM6358: make sure CBR is correctly set
+    - tracing: Build event generation tests only as modules
+    - cipso: fix total option length computation
+    - netrom: Fix a memory leak in nr_heartbeat_expiry()
+    - ipv6: prevent possible NULL deref in fib6_nh_init()
+    - ipv6: prevent possible NULL dereference in rt6_probe()
+    - xfrm6: check ip6_dst_idev() return value in xfrm6_get_saddr()
+    - netns: Make get_net_ns() handle zero refcount net
+    - qca_spi: Make interrupt remembering atomic
+    - net/sched: act_api: rely on rcu in tcf_idr_check_alloc
+    - net/sched: act_api: fix possible infinite loop in tcf_idr_check_alloc()
+    - tipc: force a dst refcount before doing decryption
+    - net/sched: act_ct: set 'net' pointer when creating new nf_flow_table
+    - sched: act_ct: add netns into the key of tcf_ct_flow_table
+    - ptp: fix integer overflow in max_vclocks_store
+    - net: stmmac: No need to calculate speed divider when offload is disabled
+    - virtio_net: checksum offloading handling fix
+    - octeontx2-pf: Add error handling to VLAN unoffload handling
+    - netfilter: ipset: Fix suspicious rcu_dereference_protected()
+    - seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6
+      behaviors
+    - bnxt_en: Restore PTP tx_avail count in case of skb_pad() error
+    - net: usb: rtl8150 fix unintiatilzed variables in rtl8150_get_link_ksettings
+    - regulator: core: Fix modpost error "regulator_get_regmap" undefined
+    - dmaengine: idxd: Fix possible Use-After-Free in irq_process_work_list
+    - dmaengine: ioat: switch from 'pci_' to 'dma_' API
+    - dmaengine: ioat: Drop redundant pci_enable_pcie_error_reporting()
+    - dmaengine: ioatdma: Fix leaking on version mismatch
+    - dmaengine: ioat: use PCI core macros for PCIe Capability
+    - dmaengine: ioatdma: Fix error path in ioat3_dma_probe()
+    - dmaengine: ioatdma: Fix kmemleak in ioat_pci_probe()
+    - dmaengine: ioatdma: Fix missing kmem_cache_destroy()
+    - regulator: bd71815: fix ramp values
+    - ACPICA: Revert "ACPICA: avoid Info: mapping multiple BARs. Your kernel is
+      fine."
+    - RDMA/mlx5: Add check for srq max_sge attribute
+    - serial: stm32: rework RX over DMA
+    - net: do not leave a dangling sk pointer, when socket creation fails
+    - btrfs: retry block group reclaim without infinite loop
+    - KVM: x86: Always sync PIR to IRR prior to scanning I/O APIC routes
+    - ALSA: hda/realtek: Limit mic boost on N14AP7
+    - drm/i915/mso: using joiner is not possible with eDP MSO
+    - drm/radeon: fix UBSAN warning in kv_dpm.c
+    - gcov: add support for GCC 14
+    - kcov: don't lose track of remote references during softirqs
+    - tcp: clear tp->retrans_stamp in tcp_rcv_fastopen_synack()
+    - i2c: ocores: set IACK bit after core is enabled
+    - dt-bindings: i2c: google,cros-ec-i2c-tunnel: correct path to i2c-controller
+      schema
+    - arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
+    - drm/amd/display: revert Exit idle optimizations before HDCP execution
+    - perf: script: add raw|disasm arguments to --insn-trace option
+    - perf script: Show also errors for --insn-trace option
+    - ARM: dts: samsung: smdkv310: fix keypad no-autorepeat
+    - ARM: dts: samsung: exynos4412-origen: fix keypad no-autorepeat
+    - ARM: dts: samsung: smdk4412: fix keypad no-autorepeat
+    - rtlwifi: rtl8192de: Style clean-ups
+    - wifi: rtlwifi: rtl8192de: Fix 5 GHz TX power
+    - pmdomain: ti-sci: Fix duplicate PD referrals
+    - bcache: fix variable length array abuse in btree_iter
+    - tracing: Add MODULE_DESCRIPTION() to preemptirq_delay_test
+    - x86/cpu/vfm: Add new macros to work with (vendor/family/model) values
+    - x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
+    - ksmbd: ignore trailing slashes in share paths
+    - drm/i915/gt: Only kick the signal worker if there's been an update
+    - drm/i915/gt: Disarm breadcrumbs if engines are already idle
+    - Revert "kheaders: substituting --sort in archive creation"
+    - kheaders: explicitly define file modes for archived headers
+    - riscv: mm: init: try best to use IS_ENABLED(CONFIG_64BIT) instead of #ifdef
+    - riscv: fix overlap of allocated page and PTR_ERR
+    - perf/core: Fix missing wakeup when waiting for context reference
+    - PCI: Add PCI_ERROR_RESPONSE and related definitions
+    - x86/amd_nb: Check for invalid SMN reads
+    - smb: client: fix deadlock in smb2_find_smb_tcon()
+    - ACPI: x86: utils: Add Picasso to the list for forcing StorageD3Enable
+    - ACPI: x86: Force StorageD3Enable on more products
+    - gve: Add RX context.
+    - gve: Clear napi->skb before dev_kfree_skb_any()
+    - Input: ili210x - fix ili251x_read_touch_data() return value
+    - pinctrl: fix deadlock in create_pinctrl() when handling -EPROBE_DEFER
+    - pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins
+    - pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins
+    - pinctrl: rockchip: use dedicated pinctrl type for RK3328
+    - pinctrl: rockchip: fix pinmux reset in rockchip_pmx_set
+    - cifs: fix typo in module parameter enable_gcm_256
+    - drm/amdgpu: fix UBSAN warning in kv_dpm.c
+    - net: mdio: add helpers to extract clause 45 regad and devad fields
+    - net: stmmac: Assign configured channel value to EXTTS event
+    - ASoC: fsl-asoc-card: set priv->pdev before using it
+    - net: dsa: microchip: fix initial port flush problem
+    - ibmvnic: Free any outstanding tx skbs during scrq reset
+    - net: phy: micrel: add Microchip KSZ 9477 to the device table
+    - xdp: Remove WARN() from __xdp_reg_mem_model()
+    - tcp: Use BPF timeout setting for SYN ACK RTO
+    - Fix race for duplicate reqsk on identical SYN
+    - sparc: fix old compat_sys_select()
+    - sparc: fix compat recv/recvfrom syscalls
+    - parisc: use correct compat recv/recvfrom syscalls
+    - tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed TFO
+    - netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data
+      registers
+    - bpf: Take return from set_memory_ro() into account with bpf_prog_lock_ro()
+    - drm/panel: ilitek-ili9881c: Fix warning with GPIO controllers that sleep
+    - vduse: validate block features only with block devices
+    - vduse: Temporarily fail if control queue feature requested
+    - x86/fpu: Fix AMD X86_BUG_FXSAVE_LEAK fixup
+    - mtd: partitions: redboot: Added conversion of operands to a larger type
+    - bpf: Add a check for struct bpf_fib_lookup size
+    - RDMA/restrack: Fix potential invalid address access
+    - net/iucv: Avoid explicit cpumask var allocation on stack
+    - net/dpaa2: Avoid explicit cpumask var allocation on stack
+    - crypto: ecdh - explicitly zeroize private_key
+    - ALSA: emux: improve patch ioctl data validation
+    - media: dvbdev: Initialize sbuf
+    - soc: ti: wkup_m3_ipc: Send NULL dummy message instead of pointer message
+    - drm/radeon/radeon_display: Decrease the size of allocated memory
+    - nvme: fixup comment for nvme RDMA Provider Type
+    - drm/panel: simple: Add missing display timing flags for KOE TX26D202VM0BWA
+    - gpio: davinci: Validate the obtained number of IRQs
+    - gpiolib: cdev: Disallow reconfiguration without direction (uAPI v1)
+    - x86: stop playing stack games in profile_pc()
+    - parisc: use generic sys_fanotify_mark implementation
+    - ocfs2: fix DIO failure due to insufficient transaction credits
+    - mmc: sdhci-pci: Convert PCIBIOS_* return codes to errnos
+    - mmc: sdhci: Do not invert write-protect twice
+    - mmc: sdhci: Do not lock spinlock around mmc_gpio_get_ro()
+    - i2c: testunit: don't erase registers after STOP
+    - i2c: testunit: discard write requests while old command is running
+    - iio: adc: ad7266: Fix variable checking bug
+    - iio: accel: fxls8962af: select IIO_BUFFER & IIO_KFIFO_BUF
+    - iio: chemical: bme680: Fix pressure value output
+    - iio: chemical: bme680: Fix calibration data variable
+    - iio: chemical: bme680: Fix overflows in compensate() functions
+    - iio: chemical: bme680: Fix sensor data read operation
+    - net: usb: ax88179_178a: improve link status logs
+    - usb: gadget: printer: SS+ support
+    - usb: gadget: printer: fix races against disable
+    - usb: musb: da8xx: fix a resource leak in probe()
+    - usb: atm: cxacru: fix endpoint checking in cxacru_bind()
+    - usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to
+      avoid deadlock
+    - serial: 8250_omap: Implementation of Errata i2310
+    - tty: mcf: MCF54418 has 10 UARTS
+    - net: can: j1939: Initialize unused data in j1939_send_one()
+    - net: can: j1939: recover socket queue on CAN bus error during BAM
+      transmission
+    - net: can: j1939: enhanced error handling for tightly received RTS messages
+      in xtp_rx_rts_session_new
+    - cpu/hotplug: Fix dynstate assignment in __cpuhp_setup_state_cpuslocked()
+    - kbuild: Install dtb files as 0644 in Makefile.dtbinst
+    - sh: rework sync_file_range ABI
+    - csky, hexagon: fix broken sys_sync_file_range
+    - hexagon: fix fadvise64_64 calling conventions
+    - drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_ld_modes
+    - drm/amdgpu: avoid using null object of framebuffer
+    - drm/i915/gt: Fix potential UAF by revoke of fence registers
+    - drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_hd_modes
+    - batman-adv: Don't accept TT entries for out-of-spec VIDs
+    - ata: ahci: Clean up sysfs file on error
+    - ata: libata-core: Fix double free on error
+    - ftruncate: pass a signed offset
+    - syscalls: fix compat_sys_io_pgetevents_time64 usage
+    - syscalls: fix sys_fanotify_mark prototype
+    - pwm: stm32: Refuse too small period requests
+    - nfs: Leave pages in the pagecache if readpage failed
+    - drivers: fix typo in firmware/efi/memmap.c
+    - efi: Correct comment on efi_memmap_alloc
+    - efi: memmap: Move manipulation routines into x86 arch tree
+    - efi: xen: Set EFI_PARAVIRT for Xen dom0 boot on all architectures
+    - efi/x86: Free EFI memory map only when installing a new one.
+    - KVM: arm64: vgic-v4: Make the doorbell request robust w.r.t preemption
+    - ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
+    - arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
+    - arm64: dts: rockchip: Add sound-dai-cells for RK3368
+    - serial: 8250_omap: Fix Errata i2310 with RX FIFO level check
+    - tracing/net_sched: NULL pointer dereference in perf_trace_qdisc_reset()
+    - Linux 5.15.162
+
+  * Fix L2CAP/LE/CPU/BI-02-C bluetooth certification failure  (LP: #2072858) //
+    Jammy update: v5.15.162 upstream stable release (LP: #2073765)
+    - Bluetooth: L2CAP: Fix rejecting L2CAP_CONN_PARAM_UPDATE_REQ
+
+  * net/sched: Fix conntrack use-after-free (LP: #2073092)
+    - net/sched: Fix UAF when resolving a clash
+
+  * Jammy update: v5.15.161 upstream stable release (LP: #2072617)
+    - x86/tsc: Trust initial offset in architectural TSC-adjust MSRs
+    - tty: n_gsm: fix missing receive state reset after mode switch
+    - speakup: Fix sizeof() vs ARRAY_SIZE() bug
+    - serial: 8250_bcm7271: use default_mux_rate if possible
+    - Revert "r8169: don't try to disable interrupts if NAPI is, scheduled
+      already"
+    - r8169: Fix possible ring buffer corruption on fragmented Tx packets.
+    - ring-buffer: Fix a race between readers and resize checks
+    - tools/latency-collector: Fix -Wformat-security compile warns
+    - net: smc91x: Fix m68k kernel compilation for ColdFire CPU
+    - nilfs2: fix unexpected freezing of nilfs_segctor_sync()
+    - nilfs2: fix potential hang in nilfs_detach_log_writer()
+    - fs/ntfs3: Remove max link count info display during driver init
+    - fs/ntfs3: Taking DOS names into account during link counting
+    - fs/ntfs3: Fix case when index is reused during tree transformation
+    - fs/ntfs3: Break dir enumeration if directory contents error
+    - ALSA: core: Fix NULL module pointer assignment at card init
+    - wifi: cfg80211: fix the order of arguments for trace events of the tx_rx_evt
+      class
+    - dt-bindings: rockchip: grf: Add missing type to 'pcie-phy' node
+    - net: usb: qmi_wwan: add Telit FN920C04 compositions
+    - drm/amd/display: Set color_mgmt_changed to true on unsuspend
+    - selftests: sud_test: return correct emulated syscall value on RISC-V
+    - regulator: irq_helpers: duplicate IRQ name
+    - ASoC: rt5645: Fix the electric noise due to the CBJ contacts floating
+    - ASoC: dt-bindings: rt5645: add cbj sleeve gpio property
+    - regulator: vqmmc-ipq4019: fix module autoloading
+    - ASoC: rt715: add vendor clear control register
+    - ASoC: rt715-sdca: volume step modification
+    - softirq: Fix suspicious RCU usage in __do_softirq()
+    - ASoC: da7219-aad: fix usage of device_get_named_child_node()
+    - drm/amdkfd: Flush the process wq before creating a kfd_process
+    - x86/mm: Remove broken vsyscall emulation code from the page fault code
+    - nvme: find numa distance only if controller has valid numa id
+    - epoll: be better about file lifetimes
+    - openpromfs: finish conversion to the new mount API
+    - crypto: bcm - Fix pointer arithmetic
+    - mm/slub, kunit: Use inverted data to corrupt kmem cache
+    - firmware: raspberrypi: Use correct device for DMA mappings
+    - ecryptfs: Fix buffer size for tag 66 packet
+    - nilfs2: fix out-of-range warning
+    - parisc: add missing export of __cmpxchg_u8()
+    - crypto: ccp - drop platform ifdef checks
+    - crypto: x86/nh-avx2 - add missing vzeroupper
+    - crypto: x86/sha256-avx2 - add missing vzeroupper
+    - crypto: x86/sha512-avx2 - add missing vzeroupper
+    - s390/cio: fix tracepoint subchannel type field
+    - jffs2: prevent xattr node from overflowing the eraseblock
+    - soc: mediatek: cmdq: Fix typo of CMDQ_JUMP_RELATIVE
+    - null_blk: Fix missing mutex_destroy() at module removal
+    - md: fix resync softlockup when bitmap size is less than array size
+    - wifi: ath10k: poll service ready message before failing
+    - x86/boot: Ignore relocations in .notes sections in walk_relocs() too
+    - sched/fair: Add EAS checks before updating root_domain::overutilized
+    - qed: avoid truncating work queue length
+    - bpf: Pack struct bpf_fib_lookup
+    - scsi: ufs: qcom: Perform read back after writing reset bit
+    - scsi: ufs: qcom: Perform read back after writing REG_UFS_SYS1CLK_1US
+    - scsi: ufs: ufs-qcom: Fix the Qcom register name for offset 0xD0
+    - scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5
+    - scsi: ufs: qcom: Perform read back after writing unipro mode
+    - scsi: ufs: qcom: Perform read back after writing CGC enable
+    - scsi: ufs: cdns-pltfrm: Perform read back after writing HCLKDIV
+    - scsi: ufs: core: Perform read back after disabling interrupts
+    - scsi: ufs: core: Perform read back after disabling UIC_COMMAND_COMPL
+    - irqchip/alpine-msi: Fix off-by-one in allocation error path
+    - irqchip/loongson-pch-msi: Fix off-by-one on allocation error path
+    - ACPI: disable -Wstringop-truncation
+    - gfs2: Don't forget to complete delayed withdraw
+    - gfs2: Fix "ignore unlock failures after withdraw"
+    - selftests/bpf: Fix umount cgroup2 error in test_sockmap
+    - cpufreq: Reorganize checks in cpufreq_offline()
+    - cpufreq: Split cpufreq_offline()
+    - cpufreq: Rearrange locking in cpufreq_remove_dev()
+    - cpufreq: exit() callback is optional
+    - net: export inet_lookup_reuseport and inet6_lookup_reuseport
+    - net: remove duplicate reuseport_lookup functions
+    - udp: Avoid call to compute_score on multiple sites
+    - cppc_cpufreq: Fix possible null pointer dereference
+    - scsi: libsas: Fix the failure of adding phy with zero-address to port
+    - scsi: hpsa: Fix allocation size for Scsi_Host private data
+    - x86/purgatory: Switch to the position-independent small code model
+    - thermal/drivers/tsens: Fix null pointer dereference
+    - wifi: ath10k: Fix an error code problem in
+      ath10k_dbg_sta_write_peer_debug_trigger()
+    - wifi: ath10k: populate board data for WCN3990
+    - net: dsa: mv88e6xxx: Add support for model-specific pre- and post-reset
+      handlers
+    - net: dsa: mv88e6xxx: Avoid EEPROM timeout without EEPROM on 88E6250-family
+      switches
+    - tcp: avoid premature drops in tcp_add_backlog()
+    - pwm: sti: Convert to platform remove callback returning void
+    - pwm: sti: Prepare removing pwm_chip from driver data
+    - pwm: sti: Simplify probe function using devm functions
+    - net: give more chances to rcu in netdev_wait_allrefs_any()
+    - macintosh/via-macii: Fix "BUG: sleeping function called from invalid
+      context"
+    - wifi: carl9170: add a proper sanity check for endpoints
+    - wifi: ar5523: enable proper endpoint verification
+    - sh: kprobes: Merge arch_copy_kprobe() into arch_prepare_kprobe()
+    - Revert "sh: Handle calling csum_partial with misaligned data"
+    - selftests/binderfs: use the Makefile's rules, not Make's implicit rules
+    - selftests/resctrl: fix clang build failure: use LOCAL_HDRS
+    - HID: intel-ish-hid: ipc: Add check for pci_alloc_irq_vectors
+    - scsi: bfa: Ensure the copied buf is NUL terminated
+    - scsi: qedf: Ensure the copied buf is NUL terminated
+    - scsi: qla2xxx: Fix debugfs output for fw_resource_count
+    - wifi: mwl8k: initialize cmd->addr[] properly
+    - usb: aqc111: stop lying about skb->truesize
+    - net: usb: sr9700: stop lying about skb->truesize
+    - m68k: Fix spinlock race in kernel thread creation
+    - m68k: mac: Fix reboot hang on Mac IIci
+    - net: ipv6: fix wrong start position when receive hop-by-hop fragment
+    - eth: sungem: remove .ndo_poll_controller to avoid deadlocks
+    - net: ethernet: cortina: Locking fixes
+    - af_unix: Fix data races in unix_release_sock/unix_stream_sendmsg
+    - net: usb: smsc95xx: stop lying about skb->truesize
+    - net: openvswitch: fix overwriting ct original tuple for ICMPv6
+    - ipv6: sr: add missing seg6_local_exit
+    - ipv6: sr: fix incorrect unregister order
+    - ipv6: sr: fix invalid unregister error path
+    - net/mlx5: Discard command completions in internal error
+    - s390/bpf: Emit a barrier for BPF_FETCH instructions
+    - mptcp: SO_KEEPALIVE: fix getsockopt support
+    - printk: Let no_printk() use _printk()
+    - dev_printk: Add and use dev_no_printk()
+    - drm/amd/display: Fix potential index out of bounds in color transformation
+      function
+    - ASoC: Intel: Disable route checks for Skylake boards
+    - mtd: core: Report error if first mtd_otp_size() call fails in
+      mtd_otp_nvmem_add()
+    - mtd: rawnand: hynix: fixed typo
+    - fbdev: shmobile: fix snprintf truncation
+    - ASoC: kirkwood: Fix potential NULL dereference
+    - drm/meson: vclk: fix calculation of 59.94 fractional rates
+    - drm/mediatek: Add 0 size check to mtk_drm_gem_obj
+    - powerpc/fsl-soc: hide unused const variable
+    - fbdev: sisfb: hide unused variables
+    - media: ngene: Add dvb_ca_en50221_init return value check
+    - media: radio-shark2: Avoid led_names truncations
+    - drm: bridge: cdns-mhdp8546: Fix possible null pointer dereference
+    - media: ipu3-cio2: Use temporary storage for struct device pointer
+    - media: ipu3-cio2: Request IRQ earlier
+    - media: dt-bindings: ovti,ov2680: Fix the power supply names
+    - fbdev: sh7760fb: allow modular build
+    - media: atomisp: ssh_css: Fix a null-pointer dereference in
+      load_video_binaries
+    - drm/arm/malidp: fix a possible null pointer dereference
+    - drm: vc4: Fix possible null pointer dereference
+    - ASoC: tracing: Export SND_SOC_DAPM_DIR_OUT to its value
+    - drm/bridge: lt8912b: Don't log an error when DSI host can't be found
+    - drm/bridge: lt9611: Don't log an error when DSI host can't be found
+    - drm/bridge: tc358775: Don't log an error when DSI host can't be found
+    - drm/panel: simple: Add missing Innolux G121X1-L03 format, flags, connector
+    - drm/mipi-dsi: use correct return type for the DSC functions
+    - RDMA/mlx5: Adding remote atomic access flag to updatable flags
+    - RDMA/hns: Fix return value in hns_roce_map_mr_sg
+    - RDMA/hns: Fix deadlock on SRQ async events.
+    - RDMA/hns: Fix GMV table pagesize
+    - RDMA/hns: Use complete parentheses in macros
+    - RDMA/hns: Modify the print level of CQE error
+    - clk: qcom: mmcc-msm8998: fix venus clock issue
+    - x86/insn: Fix PUSH instruction in x86 instruction decoder opcode map
+    - ext4: avoid excessive credit estimate in ext4_tmpfile()
+    - virt: acrn: Prefer array_size and struct_size over open coded arithmetic
+    - virt: acrn: stop using follow_pfn
+    - drivers/virt/acrn: fix PFNMAP PTE checks in acrn_vm_ram_map()
+    - sunrpc: removed redundant procp check
+    - ext4: simplify calculation of blkoff in ext4_mb_new_blocks_simple
+    - ext4: fix unit mismatch in ext4_mb_new_blocks_simple
+    - ext4: try all groups in ext4_mb_new_blocks_simple
+    - ext4: remove unused parameter from ext4_mb_new_blocks_simple()
+    - ext4: fix potential unnitialized variable
+    - SUNRPC: Fix gss_free_in_token_pages()
+    - selftests/kcmp: Make the test output consistent and clear
+    - selftests/kcmp: remove unused open mode
+    - RDMA/IPoIB: Fix format truncation compilation errors
+    - selftests: net: bridge: increase IGMP/MLD exclude timeout membership
+      interval
+    - net: qrtr: ns: Fix module refcnt
+    - netrom: fix possible dead-lock in nr_rt_ioctl()
+    - af_packet: do not call packet_read_pending() from tpacket_destruct_skb()
+    - sched/fair: Allow disabling sched_balance_newidle with
+      sched_relax_domain_level
+    - sched/core: Fix incorrect initialization of the 'burst' parameter in
+      cpu_max_write()
+    - greybus: lights: check return of get_channel_from_mode
+    - f2fs: Delete f2fs_copy_page() and replace with memcpy_page()
+    - f2fs: fix to wait on page writeback in __clone_blkaddrs()
+    - soundwire: cadence: fix invalid PDI offset
+    - dmaengine: idma64: Add check for dma_set_max_seg_size
+    - firmware: dmi-id: add a release callback function
+    - serial: max3100: Lock port->lock when calling uart_handle_cts_change()
+    - serial: max3100: Update uart_driver_registered on driver removal
+    - serial: max3100: Fix bitwise types
+    - greybus: arche-ctrl: move device table to its right location
+    - PCI: tegra194: Fix probe path for Endpoint mode
+    - serial: sc16is7xx: add proper sched.h include for sched_set_fifo()
+    - dt-bindings: PCI: rcar-pci-host: Add optional regulators
+    - dt-bindings: PCI: rcar-pci-host: Add missing IOMMU properties
+    - f2fs: compress: fix to relocate check condition in
+      f2fs_{release,reserve}_compress_blocks()
+    - f2fs: convert to use sbi directly
+    - f2fs: compress: fix to relocate check condition in
+      f2fs_ioc_{,de}compress_file()
+    - f2fs: do not allow partial truncation on pinned file
+    - f2fs: fix typos in comments
+    - f2fs: fix to relocate check condition in f2fs_fallocate()
+    - f2fs: fix to check pinfile flag in f2fs_move_file_range()
+    - coresight: etm4x: Fix unbalanced pm_runtime_enable()
+    - iio: pressure: dps310: support negative temperature values
+    - coresight: etm4x: Do not hardcode IOMEM access for register restore
+    - coresight: etm4x: Do not save/restore Data trace control registers
+    - coresight: no-op refactor to make INSTP0 check more idiomatic
+    - coresight: etm4x: Cleanup TRCIDR0 register accesses
+    - coresight: etm4x: Safe access for TRCQCLTR
+    - coresight: etm4x: Fix access to resource selector registers
+    - fpga: region: Use standard dev_release for class driver
+    - fpga: region: add owner module and take its refcount
+    - microblaze: Remove gcc flag for non existing early_printk.c file
+    - microblaze: Remove early printk call from cpuinfo-static.c
+    - dt-bindings: pinctrl: mediatek: mt7622: fix array properties
+    - watchdog: bd9576_wdt: switch to using devm_fwnode_gpiod_get()
+    - watchdog: bd9576: Drop "always-running" property
+    - usb: gadget: u_audio: Clear uac pointer when freed.
+    - stm class: Fix a double free in stm_register_device()
+    - ppdev: Remove usage of the deprecated ida_simple_xx() API
+    - ppdev: Add an error check in register_device
+    - extcon: max8997: select IRQ_DOMAIN instead of depending on it
+    - PCI/EDR: Align EDR_PORT_DPC_ENABLE_DSM with PCI Firmware r3.3
+    - PCI/EDR: Align EDR_PORT_LOCATE_DSM with PCI Firmware r3.3
+    - f2fs: compress: fix to cover {reserve,release}_compress_blocks() w/ cp_rwsem
+      lock
+    - f2fs: fix to release node block count in error path of f2fs_new_node_page()
+    - f2fs: compress: don't allow unaligned truncation on released compress inode
+    - serial: sh-sci: protect invalidating RXDMA on shutdown
+    - libsubcmd: Fix parse-options memory leak
+    - s390/vdso: filter out mno-pic-data-is-text-relative cflag
+    - s390/vdso64: filter out munaligned-symbols flag for vdso
+    - s390/vdso: Generate unwind information for C modules
+    - s390/vdso: Use standard stack frame layout
+    - s390/ipl: Fix incorrect initialization of len fields in nvme reipl block
+    - s390/ipl: Fix incorrect initialization of nvme dump block
+    - s390/boot: Remove alt_stfle_fac_list from decompressor
+    - Input: ims-pcu - fix printf string overflow
+    - Input: ioc3kbd - convert to platform remove callback returning void
+    - Input: ioc3kbd - add device table
+    - mmc: sdhci_am654: Add tuning algorithm for delay chain
+    - mmc: sdhci_am654: Write ITAPDLY for DDR52 timing
+    - mmc: sdhci_am654: Drop lookup for deprecated ti,otap-del-sel
+    - mmc: sdhci_am654: Add OTAP/ITAP delay enable
+    - mmc: sdhci_am654: Add ITAPDLYSEL in sdhci_j721e_4bit_set_clock
+    - mmc: sdhci_am654: Fix ITAPDLY for HS400 timing
+    - Input: pm8xxx-vibrator - correct VIB_MAX_LEVELS calculation
+    - drm/msm/dsi: Print dual-DSI-adjusted pclk instead of original mode pclk
+    - drm/msm/dpu: Always flush the slave INTF on the CTL
+    - um: Fix return value in ubd_init()
+    - um: vector: fix bpfflash parameter evaluation
+    - fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
+    - fs/ntfs3: Use variable length array instead of fixed size
+    - drm/bridge: tc358775: fix support for jeida-18 and jeida-24
+    - media: stk1160: fix bounds checking in stk1160_copy_video()
+    - scsi: qla2xxx: Replace all non-returning strlcpy() with strscpy()
+    - Input: cyapa - add missing input core locking to suspend/resume functions
+    - media: flexcop-usb: clean up endpoint sanity checks
+    - media: flexcop-usb: fix sanity check of bNumEndpoints
+    - powerpc/pseries: Add failure related checks for h_get_mpp and h_get_ppp
+    - um: Fix the -Wmissing-prototypes warning for __switch_mm
+    - media: cec: cec-adap: always cancel work in cec_transmit_msg_fh
+    - media: cec: cec-api: add locking in cec_release()
+    - media: cec: call enable_adap on s_log_addrs
+    - media: cec: abort if the current transmit was canceled
+    - media: cec: correctly pass on reply results
+    - media: cec: use call_op and check for !unregistered
+    - media: cec-adap.c: drop activate_cnt, use state info instead
+    - media: cec: core: avoid recursive cec_claim_log_addrs
+    - media: cec: core: avoid confusing "transmit timed out" message
+    - null_blk: Fix the WARNING: modpost: missing MODULE_DESCRIPTION()
+    - ASoC: mediatek: mt8192: fix register configuration for tdm
+    - regulator: bd71828: Don't overwrite runtime voltages
+    - x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when
+      UNWINDER_FRAME_POINTER=y
+    - [Config] Update CONFIG_ARCH_WANT_FRAME_POINTERS
+    - net: Always descend into dsa/ folder with CONFIG_NET_DSA enabled
+    - ipv6: sr: fix missing sk_buff release in seg6_input_core
+    - nfc: nci: Fix uninit-value in nci_rx_work
+    - ASoC: tas2552: Add TX path for capturing AUDIO-OUT data
+    - NFSv4: Fixup smatch warning for ambiguous return
+    - sunrpc: fix NFSACL RPC retry on soft mount
+    - rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
+    - af_unix: Update unix_sk(sk)->oob_skb under sk_receive_queue lock.
+    - ipv6: sr: fix memleak in seg6_hmac_init_algo
+    - tcp: Fix shift-out-of-bounds in dctcp_update_alpha().
+    - openvswitch: Set the skbuff pkt_type for proper pmtud support.
+    - arm64: asm-bug: Add .align 2 to the end of __BUG_ENTRY
+    - virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
+    - riscv: stacktrace: Make walk_stackframe cross pt_regs frame
+    - riscv: stacktrace: fixed walk_stackframe()
+    - net: fec: avoid lock evasion when reading pps_enable
+    - tls: fix missing memory barrier in tls_init
+    - nfc: nci: Fix kcov check in nci_rx_work()
+    - nfc: nci: Fix handling of zero-length payload packets in nci_rx_work()
+    - ice: Interpret .set_channels() input differently
+    - netfilter: nfnetlink_queue: acquire rcu_read_lock() in
+      instance_destroy_rcu()
+    - netfilter: nft_payload: restore vlan q-in-q match support
+    - spi: Don't mark message DMA mapped when no transfer in it is
+    - dma-mapping: benchmark: fix node id validation
+    - dma-mapping: benchmark: handle NUMA_NO_NODE correctly
+    - nvmet: fix ns enable/disable possible hang
+    - net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061
+    - net/mlx5e: Fix IPsec tunnel mode offload feature check
+    - net/mlx5e: Use rx_missed_errors instead of rx_dropped for reporting buffer
+      exhaustion
+    - dma-buf/sw-sync: don't enable IRQ from sync_print_obj()
+    - bpf: Fix potential integer overflow in resolve_btfids
+    - enic: Validate length of nl attributes in enic_set_vf_port
+    - net: usb: smsc95xx: fix changing LED_SEL bit value updated from EEPROM
+    - bpf: Allow delete from sockmap/sockhash only if update is allowed
+    - net:fec: Add fec_enet_deinit()
+    - netfilter: nft_payload: move struct nft_payload_set definition where it
+      belongs
+    - netfilter: nft_payload: rebuild vlan header when needed
+    - netfilter: nft_payload: rebuild vlan header on h_proto access
+    - netfilter: nft_payload: skbuff vlan metadata mangle support
+    - netfilter: tproxy: bail out if IP has been disabled on the device
+    - kconfig: fix comparison to constant symbols, 'm', 'n'
+    - spi: stm32: Don't warn about spurious interrupts
+    - net: ena: Add capabilities field with support for ENI stats capability
+    - net: ena: Extract recurring driver reset code into a function
+    - net: ena: Do not waste napi skb cache
+    - net: ena: Add dynamic recycling mechanism for rx buffers
+    - net: ena: Reduce lines with longer column width boundary
+    - net: ena: Fix redundant device NUMA node override
+    - ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
+    - hwmon: (shtc1) Fix property misspelling
+    - ALSA: timer: Set lower bound of start tick time
+    - KVM: x86: Don't advertise guest.MAXPHYADDR as host.MAXPHYADDR in CPUID
+    - genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
+    - net: ena: Fix DMA syncing in XDP path when SWIOTLB is on
+    - media: cec: core: add adap_nb_transmit_canceled() callback
+    - SUNRPC: Fix loop termination condition in gss_free_in_token_pages()
+    - drm: Check output polling initialized before disabling
+    - drm: Check polling initialized before enabling in
+      drm_helper_probe_single_connector_modes
+    - mmc: core: Do not force a retune before RPMB switch
+    - io_uring: fail NOP if non-zero op flags is passed in
+    - afs: Don't cross .backup mountpoint from backup volume
+    - nilfs2: fix use-after-free of timer for log writer thread
+    - mptcp: fix full TCP keep-alive support
+    - vxlan: Fix regression when dropping packets due to invalid src addresses
+    - net: dsa: sja1105: always enable the INCL_SRCPT option
+    - net: dsa: tag_sja1105: always prefer source port information from INCL_SRCPT
+    - scripts/gdb: fix SB_* constants parsing
+    - sunrpc: exclude from freezer when waiting for requests:
+    - f2fs: fix to do sanity check on i_xattr_nid in sanity_check_inode()
+    - media: lgdt3306a: Add a check against null-pointer-def
+    - drm/amdgpu: add error handle to avoid out-of-bounds
+    - ata: pata_legacy: make legacy_exit() work again
+    - thermal/drivers/qcom/lmh: Check for SCM availability at probe
+    - soc: qcom: rpmh-rsc: Enhance check for VRM in-flight request
+    - ACPI: resource: Do IRQ override on TongFang GXxHRXx and GMxHGxx
+    - arm64: tegra: Correct Tegra132 I2C alias
+    - arm64: dts: qcom: qcs404: fix bluetooth device address
+    - md/raid5: fix deadlock that raid5d() wait for itself to clear
+      MD_SB_CHANGE_PENDING
+    - wifi: rtl8xxxu: Fix the TX power of RTL8192CU, RTL8723AU
+    - wifi: rtlwifi: rtl8192de: Fix low speed with WPA3-SAE
+    - wifi: rtlwifi: rtl8192de: Fix endianness issue in RX path
+    - arm64: dts: hi3798cv200: fix the size of GICR
+    - media: mc: mark the media devnode as registered from the, start
+    - media: mxl5xx: Move xpt structures off stack
+    - media: v4l2-core: hold videodev_lock until dev reg, finishes
+    - mmc: core: Add mmc_gpiod_set_cd_config() function
+    - mmc: sdhci-acpi: Sort DMI quirks alphabetically
+    - mmc: sdhci-acpi: Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
+    - mmc: sdhci-acpi: Disable write protect detection on Toshiba WT10-A
+    - fbdev: savage: Handle err return when savagefb_check_var failed
+    - drm/amdgpu/atomfirmware: add intergrated info v2.3 table
+    - KVM: arm64: Fix AArch32 register narrowing on userspace write
+    - KVM: arm64: Allow AArch32 PSTATE.M to be restored as System mode
+    - crypto: ecdsa - Fix module auto-load on add-key
+    - crypto: ecrdsa - Fix module auto-load on add_key
+    - crypto: qat - Fix ADF_DEV_RESET_SYNC memory leak
+    - net/ipv6: Fix route deleting failure when metric equals 0
+    - net/9p: fix uninit-value in p9_client_rpc()
+    - intel_th: pci: Add Meteor Lake-S CPU support
+    - sparc64: Fix number of online CPUs
+    - watchdog: rti_wdt: Set min_hw_heartbeat_ms to accommodate a safety margin
+    - kdb: Fix buffer overflow during tab-complete
+    - kdb: Use format-strings rather than '\0' injection in kdb_read()
+    - kdb: Fix console handling when editing and tab-completing commands
+    - kdb: Merge identical case statements in kdb_read()
+    - kdb: Use format-specifiers rather than memset() for padding in kdb_read()
+    - net: fix __dst_negative_advice() race
+    - sparc: move struct termio to asm/termios.h
+    - ext4: set type of ac_groups_linear_remaining to __u32 to avoid overflow
+    - ext4: fix mb_cache_entry's e_refcnt leak in ext4_xattr_block_cache_find()
+    - s390/ap: Fix crash in AP internal function modify_bitmap()
+    - s390/cpacf: Split and rework cpacf query functions
+    - s390/cpacf: Make use of invalid opcode produce a link error
+    - i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
+    - EDAC/igen6: Convert PCIBIOS_* return codes to errnos
+    - nfs: fix undefined behavior in nfs_block_bits()
+    - NFS: Fix READ_PLUS when server doesn't support OP_READ_PLUS
+    - scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW major version > 5
+    - Linux 5.15.161
+
+  * Virtualbox Guru meditation on VM start caused by kernel commit in v6.9-rc4
+    (LP: #2073267)
+    - SAUCE: Revert "randomize_kstack: Improve entropy diffusion"
+
+  * CVE-2024-26921
+    - inet: inet_defrag: prevent sk release while still in use
+
+  * Jammy update: v5.15.162 upstream stable release (LP: #2073765) //
+    CVE-2024-39484
+    - mmc: davinci: Don't strip remove function when driver is builtin
+
+  * CVE-2024-39292
+    - um: Add winch to winch_handlers before registering winch IRQ
+
+  * CVE-2024-36901
+    - ipv6: prevent NULL dereference in ip6_output()
+
+  * CVE-2024-26830
+    - i40e: Do not allow untrusted VF to remove administratively set MAC
+
+  * CVE-2024-26680
+    - net: atlantic: Fix DMA mapping for PTP hwts ring
+
+  * CVE-2023-52760
+    - gfs2: Fix slab-use-after-free in gfs2_qd_dealloc
+
+  * CVE-2023-52629
+    - sh: push-switch: Reorder cleanup operations to avoid use-after-free bug
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Fri, 02 Aug 2024 20:11:12 +0200
+
+linux (5.15.0-118.128) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-118.128 -proposed tracker (LP: #2072255)
+
+  * Jammy update: v5.15.160 upstream stable release (LP: #2070292)
+    - drm/amd/display: Fix division by zero in setup_dsc_config
+    - pinctrl: core: handle radix_tree_insert() errors in
+      pinctrl_register_one_pin()
+    - nfsd: don't allow nfsd threads to be signalled.
+    - KEYS: trusted: Fix memory leak in tpm2_key_encode()
+    - Revert "selftests: mm: fix map_hugetlb failure on 64K page size systems"
+    - net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access
+    - net: bcmgenet: synchronize UMAC_CMD access
+    - netlink: annotate lockless accesses to nlk->max_recvmsg_len
+    - netlink: annotate data-races around sk->sk_err
+    - KVM: x86: Clear "has_error_code", not "error_code", for RM exception
+      injection
+    - drm/amdgpu: Fix possible NULL dereference in
+      amdgpu_ras_query_error_status_helper()
+    - binder: fix max_thread type inconsistency
+    - usb: typec: ucsi: displayport: Fix potential deadlock
+    - serial: kgdboc: Fix NMI-safety problems from keyboard reset code
+    - remoteproc: mediatek: Make sure IPI buffer fits in L2TCM
+    - KEYS: trusted: Do not use WARN when encode fails
+    - admin-guide/hw-vuln/core-scheduling: fix return type of PR_SCHED_CORE_GET
+    - docs: kernel_include.py: Cope with docutils 0.21
+    - Linux 5.15.160
+
+  * Jammy update: v5.15.159 upstream stable release (LP: #2070028)
+    - dmaengine: pl330: issue_pending waits until WFP state
+    - dmaengine: Revert "dmaengine: pl330: issue_pending waits until WFP state"
+    - wifi: nl80211: don't free NULL coalescing rule
+    - ksmbd: fix slab-out-of-bounds in smb2_allocate_rsp_buf
+    - ksmbd: validate request buffer size in smb2_allocate_rsp_buf()
+    - ksmbd: clear RENAME_NOREPLACE before calling vfs_rename
+    - eeprom: at24: Use dev_err_probe for nvmem register failure
+    - eeprom: at24: Probe for DDR3 thermal sensor in the SPD case
+    - eeprom: at24: fix memory corruption race condition
+    - pinctrl: pinctrl-aspeed-g6: Fix register offset for pinconf of GPIOR-T
+    - pinctrl/meson: fix typo in PDM's pin name
+    - pinctrl: core: delete incorrect free in pinctrl_enable()
+    - pinctrl: mediatek: paris: Rework mtk_pinconf_{get,set} switch/case logic
+    - pinctrl: mediatek: paris: Fix PIN_CONFIG_INPUT_SCHMITT_ENABLE readback
+    - pinctrl: mediatek: paris: Rework support for
+      PIN_CONFIG_{INPUT,OUTPUT}_ENABLE
+    - sunrpc: add a struct rpc_stats arg to rpc_create_args
+    - nfs: expose /proc/net/sunrpc/nfs in net namespaces
+    - nfs: make the rpc_stat per net namespace
+    - nfs: Handle error of rpc_proc_register() in nfs_net_init().
+    - power: rt9455: hide unused rt9455_boost_voltage_values
+    - power: supply: mt6360_charger: Fix of_match for usb-otg-vbus regulator
+    - pinctrl: devicetree: fix refcount leak in pinctrl_dt_to_map()
+    - regulator: mt6360: De-capitalize devicetree regulator subnodes
+    - bpf, kconfig: Fix DEBUG_INFO_BTF_MODULES Kconfig definition
+    - bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue
+    - bpf: Fix a verifier verbose message
+    - spi: hisi-kunpeng: Delete the dump interface of data registers in debugfs
+    - s390/mm: Fix storage key clearing for guest huge pages
+    - s390/mm: Fix clearing storage keys for huge pages
+    - xdp: Move conversion to xdp_frame out of map functions
+    - xdp: Add xdp_do_redirect_frame() for pre-computed xdp_frames
+    - xdp: use flags field to disambiguate broadcast redirect
+    - bna: ensure the copied buf is NUL terminated
+    - octeontx2-af: avoid off-by-one read from userspace
+    - nsh: Restore skb->{protocol,data,mac_header} for outer header in
+      nsh_gso_segment().
+    - net l2tp: drop flow hash on forward
+    - s390/vdso: Add CFI for RA register to asm macro vdso_func
+    - net: qede: sanitize 'rc' in qede_add_tc_flower_fltr()
+    - net: qede: use return from qede_parse_flow_attr() for flower
+    - net: qede: use return from qede_parse_flow_attr() for flow_spec
+    - net: qede: use return from qede_parse_actions()
+    - ASoC: meson: axg-fifo: use FIELD helpers
+    - ASoC: meson: axg-fifo: use threaded irq to check periods
+    - ASoC: meson: axg-card: make links nonatomic
+    - ASoC: meson: axg-tdm-interface: manage formatters in trigger
+    - ASoC: meson: cards: select SND_DYNAMIC_MINORS
+    - ALSA: hda: intel-sdw-acpi: fix usage of device_get_named_child_node()
+    - s390/cio: Ensure the copied buf is NUL terminated
+    - cxgb4: Properly lock TX queue for the selftest.
+    - net: dsa: mv88e6xxx: Fix number of databases for 88E6141 / 88E6341
+    - net: bridge: fix multicast-to-unicast with fraglist GSO
+    - net: core: reject skb_copy(_expand) for fraglist GSO skbs
+    - tipc: fix a possible memleak in tipc_buf_append
+    - s390/qeth: don't keep track of Input Queue count
+    - s390/qeth: Fix kernel panic after setting hsuid
+    - drm/panel: ili9341: Respect deferred probe
+    - drm/panel: ili9341: Use predefined error codes
+    - net: gro: add flush check in udp_gro_receive_segment
+    - clk: sunxi-ng: h6: Reparent CPUX during PLL CPUX rate change
+    - KVM: arm64: vgic-v2: Use cpuid from userspace as vcpu_id
+    - KVM: arm64: vgic-v2: Check for non-NULL vCPU in vgic_v2_parse_attr()
+    - scsi: lpfc: Move NPIV's transport unregistration to after resource clean up
+    - scsi: lpfc: Update lpfc_ramp_down_queue_handler() logic
+    - scsi: lpfc: Replace hbalock with ndlp lock in lpfc_nvme_unregister_port()
+    - gfs2: Fix invalid metadata access in punch_hole
+    - wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc
+    - wifi: cfg80211: fix rdev_dump_mpp() arguments order
+    - net: mark racy access on sk->sk_rcvbuf
+    - scsi: bnx2fc: Remove spin_lock_bh while releasing resources after upload
+    - btrfs: return accurate error code on open failure in open_fs_devices()
+    - kbuild: Disable KCSAN for autogenerated *.mod.c intermediaries
+    - ALSA: line6: Zero-initialize message buffers
+    - net: bcmgenet: Reset RBUF on first open
+    - ata: sata_gemini: Check clk_enable() result
+    - firewire: ohci: mask bus reset interrupts between ISR and bottom half
+    - tools/power turbostat: Fix added raw MSR output
+    - tools/power turbostat: Fix Bzy_MHz documentation typo
+    - btrfs: make btrfs_clear_delalloc_extent() free delalloc reserve
+    - btrfs: always clear PERTRANS metadata during commit
+    - scsi: target: Fix SELinux error when systemd-modules loads the target module
+    - blk-iocost: avoid out of bounds shift
+    - gpu: host1x: Do not setup DMA for virtual devices
+    - MIPS: scall: Save thread_info.syscall unconditionally on entry
+    - selftests: timers: Fix valid-adjtimex signed left-shift undefined behavior
+    - iommu: mtk: fix module autoloading
+    - fs/9p: only translate RWX permissions for plain 9P2000
+    - fs/9p: translate O_TRUNC into OTRUNC
+    - 9p: explicitly deny setlease attempts
+    - gpio: wcove: Use -ENOTSUPP consistently
+    - gpio: crystalcove: Use -ENOTSUPP consistently
+    - clk: Don't hold prepare_lock when calling kref_put()
+    - fs/9p: drop inodes immediately on non-.L too
+    - drm/nouveau/dp: Don't probe eDP ports twice harder
+    - net:usb:qmi_wwan: support Rolling modules
+    - bpf, sockmap: TCP data stall on recv before accept
+    - bpf, sockmap: Handle fin correctly
+    - bpf, sockmap: Convert schedule_work into delayed_work
+    - bpf, sockmap: Reschedule is now done through backlog
+    - bpf, sockmap: Improved check for empty queue
+    - qibfs: fix dentry leak
+    - xfrm: Preserve vlan tags for transport mode software GRO
+    - ARM: 9381/1: kasan: clear stale stack poison
+    - tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets
+    - tcp: Use refcount_inc_not_zero() in tcp_twsk_unique().
+    - Bluetooth: Fix use-after-free bugs caused by sco_sock_timeout
+    - Bluetooth: l2cap: fix null-ptr-deref in l2cap_chan_timeout
+    - rtnetlink: Correct nested IFLA_VF_VLAN_LIST attribute validation
+    - hwmon: (corsair-cpro) Use a separate buffer for sending commands
+    - hwmon: (corsair-cpro) Use complete_all() instead of complete() in
+      ccp_raw_event()
+    - hwmon: (corsair-cpro) Protect ccp->wait_input_report with a spinlock
+    - phonet: fix rtm_phonet_notify() skb allocation
+    - net: bridge: fix corrupted ethernet header on multicast-to-unicast
+    - ipv6: fib6_rules: avoid possible NULL dereference in fib6_rule_action()
+    - net: hns3: PF support get unicast MAC address space assigned by firmware
+    - net: hns3: using user configure after hardware reset
+    - net: hns3: add log for workqueue scheduled late
+    - net: hns3: add query vf ring and vector map relation
+    - net: hns3: refactor function hclge_mbx_handler()
+    - net: hns3: direct return when receive a unknown mailbox message
+    - net: hns3: refactor hns3 makefile to support hns3_common module
+    - net: hns3: create new cmdq hardware description structure hclge_comm_hw
+    - net: hns3: create new set of unified hclge_comm_cmd_send APIs
+    - net: hns3: refactor hclge_cmd_send with new hclge_comm_cmd_send API
+    - net: hns3: change type of numa_node_mask as nodemask_t
+    - net: hns3: use appropriate barrier function after setting a bit value
+    - net: hns3: split function hclge_init_vlan_config()
+    - net: hns3: fix port vlan filter not disabled issue
+    - drm/meson: dw-hdmi: power up phy on device init
+    - drm/meson: dw-hdmi: add bandgap setting for g12
+    - drm/connector: Add \n to message about demoting connector force-probes
+    - drm/amd/display: Atom Integrated System Info v2_2 for DCN35
+    - Revert "Revert "ACPI: CPPC: Use access_width over bit_width for system
+      memory accesses""
+    - ACPI: CPPC: Fix bit_offset shift in MASK_VAL() macro
+    - ACPI: CPPC: Fix access width used for PCC registers
+    - btrfs: fix kvcalloc() arguments order in btrfs_ioctl_send()
+    - firewire: nosy: ensure user_length is taken into account when fetching
+      packet contents
+    - Reapply "drm/qxl: simplify qxl_fence_wait"
+    - arm64: dts: qcom: Fix 'interrupt-map' parent address cells
+    - usb: typec: ucsi: Check for notifications after init
+    - usb: typec: ucsi: Fix connector check on init
+    - usb: Fix regression caused by invalid ep0 maxpacket in virtual SuperSpeed
+      device
+    - usb: ohci: Prevent missed ohci interrupts
+    - usb: gadget: composite: fix OS descriptors w_value logic
+    - usb: gadget: f_fs: Fix a race condition when processing setup packets.
+    - usb: xhci-plat: Don't include xhci.h
+    - usb: dwc3: core: Prevent phy suspend during init
+    - ALSA: hda/realtek: Fix mute led of HP Laptop 15-da3001TU
+    - btrfs: add missing mutex_unlock in btrfs_relocate_sys_chunks()
+    - mptcp: ensure snd_nxt is properly initialized on connect
+    - dt-bindings: iio: health: maxim,max30102: fix compatible check
+    - iio:imu: adis16475: Fix sync mode setting
+    - iio: accel: mxc4005: Interrupt handling fixes
+    - tipc: fix UAF in error path
+    - net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()
+    - ASoC: tegra: Fix DSPK 16-bit playback
+    - ASoC: ti: davinci-mcasp: Fix race condition during probe
+    - dyndbg: fix old BUG_ON in >control parser
+    - slimbus: qcom-ngd-ctrl: Add timeout for wait operation
+    - mei: me: add lunar lake point M DID
+    - drm/vmwgfx: Fix invalid reads in fence signaled events
+    - net: fix out-of-bounds access in ops_init
+    - hwmon: (pmbus/ucd9000) Increase delay from 250 to 500us
+    - regulator: core: fix debugfs creation regression
+    - Bluetooth: qca: add missing firmware sanity checks
+    - Bluetooth: qca: fix NVM configuration parsing
+    - Bluetooth: qca: fix firmware check error path
+    - keys: Fix overwrite of key expiration on instantiation
+    - md: fix kmemleak of rdev->serial
+    - Linux 5.15.159
+
+  * Freezing user space processes failed after 20.008 seconds (1 tasks refusing
+    to freeze, wq_busy=0) (LP: #2061091)
+    - ALSA: Fix deadlocks with kctl removals at disconnection
+
+  * CVE-2024-27017
+    - netfilter: nft_set_pipapo: constify lookup fn args where possible
+    - netfilter: nft_set_pipapo: walk over current view on netlink dump
+    - netfilter: nf_tables: missing iterator type in lookup walk
+
+  * CVE-2024-26952
+    - ksmbd: fix potencial out-of-bounds when buffer offset is invalid
+
+  * CVE-2024-26886
+    - Bluetooth: af_bluetooth: Fix deadlock
+
+  * CVE-2023-52752
+    - smb: client: fix use-after-free bug in cifs_debug_data_proc_show()
+
+  * CVE-2024-25742
+    - x86/sev: Harden #VC instruction emulation somewhat
+    - x86/sev: Check for MWAITX and MONITORX opcodes in the #VC handler
+
+  * CVE-2024-36016
+    - tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 05 Jul 2024 10:53:52 +0200
+
+linux (5.15.0-116.126) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-116.126 -proposed tracker (LP: #2071603)
+
+  * idxd: NULL pointer dereference reading wq op_config attribute (LP: #2069081)
+    - SAUCE: dmaengine: idxd: set is_visible member of idxd_wq_attribute_group
+
+  * AMD GPUs fail with null pointer dereference when IOMMU enabled, leading to
+    black screen (LP: #2068738)
+    - SAUCE: Revert "drm/amdgpu: init iommu after amdkfd device init"
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Mon, 01 Jul 2024 11:13:30 +0200
+
+linux (5.15.0-115.125) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-115.125 -proposed tracker (LP: #2068396)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2024.06.10)
+
+  * Jammy update: v5.15.158 upstream stable release (LP: #2067974)
+    - smb: client: fix rename(2) regression against samba
+    - cifs: reinstate original behavior again for forceuid/forcegid
+    - HID: intel-ish-hid: ipc: Fix dev_err usage with uninitialized dev->devc
+    - HID: logitech-dj: allow mice to use all types of reports
+    - arm64: dts: rockchip: enable internal pull-up on Q7_USB_ID for RK3399 Puma
+    - arm64: dts: rockchip: fix alphabetical ordering RK3399 puma
+    - arm64: dts: rockchip: enable internal pull-up on PCIE_WAKE# for RK3399 Puma
+    - arm64: dts: rockchip: Remove unsupported node from the Pinebook Pro dts
+    - arm64: dts: mediatek: mt8183: Add power-domains properity to mfgcfg
+    - arm64: dts: mediatek: mt7622: add support for coherent DMA
+    - arm64: dts: mediatek: mt7622: introduce nodes for Wireless Ethernet Dispatch
+    - arm64: dts: mediatek: mt7622: fix clock controllers
+    - arm64: dts: mediatek: mt7622: fix IR nodename
+    - arm64: dts: mediatek: mt7622: fix ethernet controller "compatible"
+    - arm64: dts: mediatek: mt7622: drop "reset-names" from thermal block
+    - arm64: dts: mediatek: mt2712: fix validation errors
+    - ARC: [plat-hsdk]: Remove misplaced interrupt-cells property
+    - wifi: iwlwifi: mvm: remove old PASN station when adding a new one
+    - wifi: iwlwifi: mvm: return uid from iwl_mvm_build_scan_cmd
+    - vxlan: drop packets from invalid src-address
+    - mlxsw: core: Unregister EMAD trap using FORWARD action
+    - icmp: prevent possible NULL dereferences from icmp_build_probe()
+    - bridge/br_netlink.c: no need to return void function
+    - NFC: trf7970a: disable all regulators on removal
+    - ipv4: check for NULL idev in ip_route_use_hint()
+    - net: usb: ax88179_178a: stop lying about skb->truesize
+    - net: gtp: Fix Use-After-Free in gtp_dellink
+    - ipvs: Fix checksumming on GSO of SCTP packets
+    - net: openvswitch: Fix Use-After-Free in ovs_ct_exit
+    - mlxsw: spectrum_acl_tcam: Fix race during rehash delayed work
+    - mlxsw: spectrum_acl_tcam: Fix possible use-after-free during activity update
+    - mlxsw: spectrum_acl_tcam: Fix possible use-after-free during rehash
+    - mlxsw: spectrum_acl_tcam: Rate limit error message
+    - mlxsw: spectrum_acl_tcam: Fix memory leak during rehash
+    - mlxsw: spectrum_acl_tcam: Fix warning during rehash
+    - mlxsw: spectrum_acl_tcam: Fix incorrect list API usage
+    - mlxsw: spectrum_acl_tcam: Fix memory leak when canceling rehash work
+    - netfilter: nf_tables: honor table dormant flag from netdev release event
+      path
+    - i40e: Do not use WQ_MEM_RECLAIM flag for workqueue
+    - i40e: Report MFS in decimal base instead of hex
+    - iavf: Fix TC config comparison with existing adapter TC config
+    - net: ethernet: ti: am65-cpts: Fix PTPv1 message type on TX packets
+    - af_unix: Suppress false-positive lockdep splat for spin_lock() in
+      __unix_gc().
+    - serial: core: Provide port lock wrappers
+    - serial: mxs-auart: add spinlock around changing cts state
+    - drm-print: add drm_dbg_driver to improve namespace symmetry
+    - drm/vmwgfx: Fix crtc's atomic check conditional
+    - Revert "crypto: api - Disallow identical driver names"
+    - net/mlx5e: Fix a race in command alloc flow
+    - tracing: Show size of requested perf buffer
+    - tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker
+      together
+    - x86/cpu: Fix check for RDPKRU in __show_regs()
+    - Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old()
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0bda:0x4853
+    - Bluetooth: qca: fix NULL-deref on non-serdev suspend
+    - mmc: sdhci-msm: pervent access to suspended controller
+    - btrfs: fix information leak in btrfs_ioctl_logical_to_ino()
+    - cpu: Re-enable CPU mitigations by default for !X86 architectures
+    - [Configs] Update CPU mitigation configs
+    - arm64: dts: rockchip: enable internal pull-up for Q7_THRM# on RK3399 Puma
+    - drm/amdgpu/sdma5.2: use legacy HDP flush for SDMA2/3
+    - drm/amdgpu: Fix leak when GPU memory allocation fails
+    - irqchip/gic-v3-its: Prevent double free on error
+    - ethernet: Add helper for assigning packet type when dest address does not
+      match device address
+    - net: b44: set pause params only when interface is up
+    - stackdepot: respect __GFP_NOLOCKDEP allocation flag
+    - mtd: diskonchip: work around ubsan link failure
+    - tcp: Clean up kernel listener's reqsk in inet_twsk_purge()
+    - tcp: Fix NEW_SYN_RECV handling in inet_twsk_purge()
+    - dmaengine: owl: fix register access functions
+    - idma64: Don't try to serve interrupts when device is powered off
+    - dma: xilinx_dpdma: Fix locking
+    - dmaengine: idxd: Fix oops during rmmod on single-CPU platforms
+    - riscv: fix VMALLOC_START definition
+    - riscv: Fix TASK_SIZE on 64-bit NOMMU
+    - i2c: smbus: fix NULL function pointer dereference
+    - fbdev: fix incorrect address computation in deferred IO
+    - HID: i2c-hid: remove I2C_HID_READ_PENDING flag to prevent lock-up
+    - bounds: Use the right number of bits for power-of-two CONFIG_NR_CPUS
+    - udp: preserve the connected status if only UDP cmsg
+    - serial: core: fix kernel-doc for uart_port_unlock_irqrestore()
+    - Linux 5.15.158
+
+  * Jammy update: v5.15.157 upstream stable release (LP: #2067959)
+    - ksmbd: don't send oplock break if rename fails
+    - ksmbd: validate payload size in ipc response
+    - ksmbd: do not set SMB2_GLOBAL_CAP_ENCRYPTION for SMB 3.1.1
+    - btrfs: record delayed inode root in transaction
+    - SUNRPC: Fix rpcgss_context trace event acceptor field
+    - selftests/ftrace: Limit length in subsystem-enable tests
+    - bpf: Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support
+    - bpf: Generalize check_ctx_reg for reuse with other types
+    - bpf: Generally fix helper register offset check
+    - bpf: Fix out of bounds access for ringbuf helpers
+    - bpf: Fix ringbuf memory type confusion when passing to helpers
+    - kprobes: Fix possible use-after-free issue on kprobe registration
+    - Revert "tracing/trigger: Fix to return error if failed to alloc snapshot"
+    - netfilter: nf_tables: Fix potential data-race in __nft_expr_type_get()
+    - netfilter: nf_tables: Fix potential data-race in __nft_obj_type_get()
+    - netfilter: br_netfilter: skip conntrack input hook for promisc packets
+    - netfilter: nf_flow_table: count pending offload workqueue tasks
+    - [Config] update configs to enable new NF_FLOW_TABLE_PROCFS
+    - netfilter: flowtable: validate pppoe header
+    - netfilter: flowtable: incorrect pppoe tuple
+    - af_unix: Call manage_oob() for every skb in unix_stream_read_generic().
+    - af_unix: Don't peek OOB data without MSG_OOB.
+    - tun: limit printing rate when illegal packet received by tun dev
+    - net: dsa: mt7530: fix mirroring frames received on local port
+    - net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
+    - RDMA/rxe: Fix the problem "mutex_destroy missing"
+    - RDMA/cm: Print the old state when cm_destroy_id gets timeout
+    - RDMA/mlx5: Fix port number for counter query in multi-port configuration
+    - s390/qdio: handle deferred cc1
+    - s390/cio: fix race condition during online processing
+    - drm: nv04: Fix out of bounds access
+    - drm/panel: visionox-rm69299: don't unregister DSI device
+    - clk: Remove prepare_lock hold assertion in __clk_release()
+    - clk: Mark 'all_lists' as const
+    - clk: remove extra empty line
+    - clk: Print an info line before disabling unused clocks
+    - clk: Initialize struct clk_core kref earlier
+    - clk: Get runtime PM before walking tree during disable_unused
+    - x86/bugs: Fix BHI retpoline check
+    - x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
+    - thunderbolt: Avoid notify PM core about runtime PM resume
+    - thunderbolt: Fix wake configurations after device unplug
+    - comedi: vmk80xx: fix incomplete endpoint checking
+    - serial/pmac_zilog: Remove flawed mitigation for rx irq flood
+    - USB: serial: option: add Fibocom FM135-GL variants
+    - USB: serial: option: add support for Fibocom FM650/FG650
+    - USB: serial: option: add Lonsung U8300/U9300 product
+    - USB: serial: option: support Quectel EM060K sub-models
+    - USB: serial: option: add Rolling RW101-GL and RW135-GL support
+    - USB: serial: option: add Telit FN920C04 rmnet compositions
+    - usb: dwc2: host: Fix dereference issue in DDMA completion flow.
+    - usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport
+      error
+    - mei: me: disable RPL-S on SPS and IGN firmwares
+    - speakup: Avoid crash on very long word
+    - fs: sysfs: Fix reference leak in sysfs_break_active_protection()
+    - KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
+    - KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
+    - arm64: hibernate: Fix level3 translation fault in swsusp_save()
+    - init/main.c: Fix potential static_command_line memory overflow
+    - drm/vmwgfx: Sort primary plane formats by order of preference
+    - nouveau: fix instmem race condition around ptr stores
+    - nilfs2: fix OOB in nilfs_set_de_type
+    - net: dsa: mt7530: set all CPU ports in MT7531_CPU_PMAP
+    - net: dsa: introduce preferred_default_local_cpu_port and use on MT7530
+    - net: dsa: mt7530: fix improper frames on all 25MHz and 40MHz XTAL MT7530
+    - net: dsa: mt7530: fix enabling EEE on MT7531 switch on all boards
+    - Linux 5.15.157
+
+  * [SRU][22.04.4]: megaraid_sas: Critical Bug Fixes (LP: #2046722)
+    - scsi: megaraid_sas: Log message when controller reset is requested but not
+      issued
+    - scsi: megaraid_sas: Driver version update to 07.727.03.00-rc1
+
+  * Jammy update: v5.15.156 upstream stable release (LP: #2065857)
+    - batman-adv: Avoid infinite loop trying to resize local TT
+    - ring-buffer: Only update pages_touched when a new page is touched
+    - Bluetooth: Fix memory leak in hci_req_sync_complete()
+    - media: cec: core: remove length check of Timer Status
+    - arm64: dts: imx8-ss-conn: fix usdhc wrong lpcg clock order
+    - Revert "drm/qxl: simplify qxl_fence_wait"
+    - nouveau: fix function cast warning
+    - scsi: qla2xxx: Fix off by one in qla_edif_app_getstats()
+    - net: openvswitch: fix unwanted error log on timeout policy probing
+    - u64_stats: Disable preemption on 32bit UP+SMP PREEMPT_RT during updates.
+    - xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING
+    - geneve: fix header validation in geneve[6]_xmit_skb
+    - af_unix: Clear stale u->oob_skb.
+    - octeontx2-af: Fix NIX SQ mode and BP config
+    - ipv6: fib: hide unused 'pn' variable
+    - ipv4/route: avoid unused-but-set-variable warning
+    - ipv6: fix race condition between ipv6_get_ifaddr and ipv6_del_addr
+    - netfilter: complete validation of user input
+    - net/mlx5: Properly link new fs rules into the tree
+    - net: sparx5: fix wrong config being used when reconfiguring PCS
+    - net: dsa: mt7530: trap link-local frames regardless of ST Port State
+    - af_unix: Do not use atomic ops for unix_sk(sk)->inflight.
+    - af_unix: Fix garbage collector racing against connect()
+    - net: ena: Fix potential sign extension issue
+    - net: ena: Wrong missing IO completions check order
+    - net: ena: Fix incorrect descriptor free behavior
+    - tracing: hide unused ftrace_event_id_fops
+    - iommu/vt-d: Allocate local memory for page request queue
+    - btrfs: qgroup: correctly model root qgroup rsv in convert
+    - drm/client: Fully protect modes[] with dev->mode_config.mutex
+    - vhost: Add smp_rmb() in vhost_vq_avail_empty()
+    - perf/x86: Fix out of range data
+    - x86/cpu: Actually turn off mitigations by default for
+      SPECULATION_MITIGATIONS=n
+    - selftests: timers: Fix abs() warning in posix_timers test
+    - x86/apic: Force native_apic_mem_read() to use the MOV instruction
+    - irqflags: Explicitly ignore lockdep_hrtimer_exit() argument
+    - x86/bugs: Fix return type of spectre_bhi_state()
+    - x86/bugs: Fix BHI documentation
+    - x86/bugs: Cache the value of MSR_IA32_ARCH_CAPABILITIES
+    - x86/bugs: Rename various 'ia32_cap' variables to 'x86_arch_cap_msr'
+    - x86/bugs: Fix BHI handling of RRSBA
+    - x86/bugs: Clarify that syscall hardening isn't a BHI mitigation
+    - x86/bugs: Remove CONFIG_BHI_MITIGATION_AUTO and spectre_bhi=auto
+    - [Config] updateconfigs to remove obsolete SPECTRE_BHI_AUTO
+    - x86/bugs: Replace CONFIG_SPECTRE_BHI_{ON,OFF} with
+      CONFIG_MITIGATION_SPECTRE_BHI
+    - [Config] updateconfigs to enable new MITIGATION_SPECTRE_BHI
+    - drm/i915/cdclk: Fix CDCLK programming order when pipes are active
+    - Linux 5.15.156
+
+  * Jammy update: v5.15.155 upstream stable release (LP: #2065805)
+    - amdkfd: use calloc instead of kzalloc to avoid integer overflow
+    - net: dsa: fix panic when DSA master device unbinds on shutdown
+    - wifi: ath9k: fix LNA selection in ath_ant_try_scan()
+    - VMCI: Fix memcpy() run-time warning in dg_dispatch_as_host()
+    - panic: Flush kernel log buffer at the end
+    - cpuidle: Avoid potential overflow in integer multiplication
+    - arm64: dts: rockchip: fix rk3328 hdmi ports node
+    - arm64: dts: rockchip: fix rk3399 hdmi ports node
+    - ionic: set adminq irq affinity
+    - pstore/zone: Add a null pointer check to the psz_kmsg_read
+    - tools/power x86_energy_perf_policy: Fix file leak in get_pkg_num()
+    - net: pcs: xpcs: Return EINVAL in the internal methods
+    - wifi: ath11k: decrease MHI channel buffer length to 8KB
+    - btrfs: handle chunk tree lookup error in btrfs_relocate_sys_chunks()
+    - btrfs: export: handle invalid inode or root reference in btrfs_get_parent()
+    - btrfs: send: handle path ref underflow in header iterate_inode_ref()
+    - net/smc: reduce rtnl pressure in smc_pnet_create_pnetids_list()
+    - Bluetooth: btintel: Fix null ptr deref in btintel_read_version
+    - Input: synaptics-rmi4 - fail probing if memory allocation for "phys" fails
+    - pinctrl: renesas: checker: Limit cfg reg enum checks to provided IDs
+    - sysv: don't call sb_bread() with pointers_lock held
+    - scsi: lpfc: Fix possible memory leak in lpfc_rcv_padisc()
+    - isofs: handle CDs with bad root inode but good Joliet root directory
+    - media: sta2x11: fix irq handler cast
+    - ALSA: firewire-lib: handle quirk to calculate payload quadlets as data block
+      counter
+    - ext4: add a hint for block bitmap corrupt state in mb_groups
+    - ext4: forbid commit inconsistent quota data when errors=remount-ro
+    - drm/amd/display: Fix nanosec stat overflow
+    - SUNRPC: increase size of rpc_wait_queue.qlen from unsigned short to unsigned
+      int
+    - Revert "ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default"
+    - libperf evlist: Avoid out-of-bounds access
+    - block: prevent division by zero in blk_rq_stat_sum()
+    - RDMA/cm: add timeout to cm_destroy_id wait
+    - Input: allocate keycode for Display refresh rate toggle
+    - platform/x86: touchscreen_dmi: Add an extra entry for a variant of the Chuwi
+      Vi8 tablet
+    - ktest: force $buildonly = 1 for 'make_warnings_file' test type
+    - ring-buffer: use READ_ONCE() to read cpu_buffer->commit_page in concurrent
+      environment
+    - tools: iio: replace seekdir() in iio_generic_buffer
+    - usb: typec: tcpci: add generic tcpci fallback compatible
+    - usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
+    - ASoC: soc-core.c: Skip dummy codec when adding platforms
+    - fbdev: viafb: fix typo in hw_bitblt_1 and hw_bitblt_2
+    - drivers/nvme: Add quirks for device 126f:2262
+    - fbmon: prevent division by zero in fb_videomode_from_videomode()
+    - netfilter: nf_tables: release batch on table validation from abort path
+    - netfilter: nf_tables: release mutex after nft_gc_seq_end from abort path
+    - netfilter: nf_tables: discard table flag update with pending basechain
+      deletion
+    - tty: n_gsm: require CAP_NET_ADMIN to attach N_GSM0710 ldisc
+    - gcc-plugins/stackleak: Ignore .noinstr.text and .entry.text
+    - gcc-plugins/stackleak: Avoid .head.text section
+    - virtio: reenable config if freezing device failed
+    - x86/mm/pat: fix VM_PAT handling in COW mappings
+    - randomize_kstack: Improve entropy diffusion
+    - platform/x86: intel-vbtn: Update tablet mode switch at end of probe
+    - Bluetooth: btintel: Fixe build regression
+    - VMCI: Fix possible memcpy() run-time warning in
+      vmci_datagram_invoke_guest_handler()
+    - Linux 5.15.155
+
+  * Jammy update: v5.15.154 upstream stable release (LP: #2065435)
+    - Documentation/hw-vuln: Update spectre doc
+    - x86/cpu: Support AMD Automatic IBRS
+    - media: staging: ipu3-imgu: Set fields before media_entity_pads_init()
+    - clk: qcom: gcc-sdm845: Add soft dependency on rpmhpd
+    - smack: Set SMACK64TRANSMUTE only for dirs in smack_inode_setxattr()
+    - smack: Handle SMACK64TRANSMUTE in smack_inode_setsecurity()
+    - arm: dts: marvell: Fix maxium->maxim typo in brownstone dts
+    - drm/vmwgfx: Fix possible null pointer derefence with invalid contexts
+    - pci_iounmap(): Fix MMIO mapping leak
+    - KVM: Always flush async #PF workqueue when vCPU is being destroyed
+    - sparc64: NMI watchdog: fix return value of __setup handler
+    - sparc: vDSO: fix return value of __setup handler
+    - crypto: qat - fix double free during reset
+    - crypto: qat - resolve race condition during AER recovery
+    - selftests/mqueue: Set timeout to 180 seconds
+    - ext4: correct best extent lstart adjustment logic
+    - block: Clear zone limits for a non-zoned stacked queue
+    - kasan: test: add memcpy test that avoids out-of-bounds write
+    - kasan/test: avoid gcc warning for intentional overflow
+    - bounds: support non-power-of-two CONFIG_NR_CPUS
+    - fat: fix uninitialized field in nostale filehandles
+    - ubifs: Set page uptodate in the correct place
+    - ubi: Check for too small LEB size in VTBL code
+    - ubi: correct the calculation of fastmap size
+    - mtd: rawnand: meson: fix scrambling mode value in command macro
+    - parisc: Avoid clobbering the C/B bits in the PSW with tophys and tovirt
+      macros
+    - parisc: Fix ip_fast_csum
+    - parisc: Fix csum_ipv6_magic on 32-bit systems
+    - parisc: Fix csum_ipv6_magic on 64-bit systems
+    - parisc: Strip upper 32 bit of sum in csum_ipv6_magic for 64-bit builds
+    - PM: suspend: Set mem_sleep_current during kernel command line setup
+    - clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
+    - clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
+    - clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
+    - clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
+    - usb: xhci: Add error handling in xhci_map_urb_for_dma
+    - powerpc/fsl: Fix mfpmr build errors with newer binutils
+    - USB: serial: ftdi_sio: add support for GMC Z216C Adapter IR-USB
+    - USB: serial: add device ID for VeriFone adapter
+    - USB: serial: cp210x: add ID for MGP Instruments PDS100
+    - USB: serial: option: add MeiG Smart SLM320 product
+    - USB: serial: cp210x: add pid/vid for TDK NC0110013M and MM0110113M
+    - PM: sleep: wakeirq: fix wake irq warning in system suspend
+    - mmc: tmio: avoid concurrent runs of mmc_request_done()
+    - fuse: fix root lookup with nonzero generation
+    - fuse: don't unhash root
+    - usb: typec: ucsi: Clean up UCSI_CABLE_PROP macros
+    - printk/console: Split out code that enables default console
+    - serial: Lock console when calling into driver before registration
+    - btrfs: fix off-by-one chunk length calculation at contains_pending_extent()
+    - PCI: Drop pci_device_remove() test of pci_dev->driver
+    - PCI/PM: Drain runtime-idle callbacks before driver removal
+    - PCI: Work around Intel I210 ROM BAR overlap defect
+    - PCI/ASPM: Make Intel DG2 L1 acceptable latency unlimited
+    - PCI/DPC: Quirk PIO log size for certain Intel Root Ports
+    - PCI/DPC: Quirk PIO log size for Intel Raptor Lake Root Ports
+    - dm-raid: fix lockdep waring in "pers->hot_add_disk"
+    - mac802154: fix llsec key resources release in mac802154_llsec_key_del
+    - swap: comments get_swap_device() with usage rule
+    - mm: swap: fix race between free_swap_and_cache() and swapoff()
+    - mmc: core: Fix switch on gp3 partition
+    - drm/etnaviv: Restore some id values
+    - landlock: Warn once if a Landlock action is requested while disabled
+    - hwmon: (amc6821) add of_match table
+    - ext4: fix corruption during on-line resize
+    - nvmem: meson-efuse: fix function pointer type mismatch
+    - slimbus: core: Remove usage of the deprecated ida_simple_xx() API
+    - phy: tegra: xusb: Add API to retrieve the port number of phy
+    - usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
+    - speakup: Fix 8bit characters from direct synth
+    - PCI/AER: Block runtime suspend when handling errors
+    - nfs: fix UAF in direct writes
+    - kbuild: Move -Wenum-{compare-conditional,enum-conversion} into W=1
+    - PCI: dwc: endpoint: Fix advertised resizable BAR size
+    - vfio/platform: Disable virqfds on cleanup
+    - ksmbd: retrieve number of blocks using vfs_getattr in
+      set_file_allocation_info
+    - ring-buffer: Fix waking up ring buffer readers
+    - ring-buffer: Do not set shortest_full when full target is hit
+    - ring-buffer: Fix resetting of shortest_full
+    - ring-buffer: Fix full_waiters_pending in poll
+    - ring-buffer: Use wait_event_interruptible() in ring_buffer_wait()
+    - soc: fsl: qbman: Always disable interrupts when taking cgr_lock
+    - soc: fsl: qbman: Add helper for sanity checking cgr ops
+    - soc: fsl: qbman: Add CGR update function
+    - soc: fsl: qbman: Use raw spinlock for cgr_lock
+    - s390/zcrypt: fix reference counting on zcrypt card objects
+    - drm/panel: do not return negative error codes from drm_panel_get_modes()
+    - drm/exynos: do not return negative values from .get_modes()
+    - drm/imx/ipuv3: do not return negative values from .get_modes()
+    - drm/vc4: hdmi: do not return negative values from .get_modes()
+    - memtest: use {READ,WRITE}_ONCE in memory scanning
+    - nilfs2: fix failure to detect DAT corruption in btree and direct mappings
+    - nilfs2: prevent kernel bug at submit_bh_wbc()
+    - cpufreq: dt: always allocate zeroed cpumask
+    - x86/CPU/AMD: Update the Zenbleed microcode revisions
+    - NFSD: Fix nfsd_clid_class use of __string_len() macro
+    - net: hns3: tracing: fix hclgevf trace event strings
+    - wireguard: netlink: check for dangling peer via is_dead instead of empty
+      list
+    - wireguard: netlink: access device through ctx instead of peer
+    - ahci: asm1064: correct count of reported ports
+    - ahci: asm1064: asm1166: don't limit reported ports
+    - drm/amdgpu: amdgpu_ttm_gart_bind set gtt bound flag
+    - drm/amd/display: Return the correct HDCP error code
+    - drm/amd/display: Fix noise issue on HDMI AV mute
+    - dm snapshot: fix lockup in dm_exception_table_exit
+    - x86/pm: Work around false positive kmemleak report in msr_build_context()
+    - net: ravb: Add R-Car Gen4 support
+    - cpufreq: brcmstb-avs-cpufreq: fix up "add check for cpufreq_cpu_get's return
+      value"
+    - netfilter: nf_tables: reject constant set with timeout
+    - Drivers: hv: vmbus: Calculate ring buffer size for more efficient use of
+      memory
+    - xfrm: Avoid clang fortify warning in copy_to_user_tmpl()
+    - KVM: SVM: Flush pages under kvm->lock to fix UAF in
+      svm_register_enc_region()
+    - tracing: Use .flush() call to wake up readers
+    - drm/i915: Check before removing mm notifier
+    - USB: usb-storage: Prevent divide-by-0 error in isd200_ata_command
+    - usb: gadget: ncm: Fix handling of zero block length packets
+    - usb: port: Don't try to peer unused USB ports based on location
+    - tty: serial: fsl_lpuart: avoid idle preamble pending if CTS is enabled
+    - mei: me: add arrow lake point S DID
+    - mei: me: add arrow lake point H DID
+    - vt: fix unicode buffer corruption when deleting characters
+    - fs/aio: Check IOCB_AIO_RW before the struct aio_kiocb conversion
+    - tee: optee: Fix kernel panic caused by incorrect error handling
+    - i2c: i801: Avoid potential double call to gpiod_remove_lookup_table
+    - xen/events: close evtchn after mapping cleanup
+    - clocksource/drivers/arm_global_timer: Fix maximum prescaler value
+    - entry: Respect changes to system call number by trace_sys_enter()
+    - minmax: add umin(a, b) and umax(a, b)
+    - swiotlb: Fix alignment checks when both allocation and DMA masks are present
+    - dma-mapping: add dma_opt_mapping_size()
+    - dma-iommu: add iommu_dma_opt_mapping_size()
+    - iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
+    - printk: Update @console_may_schedule in console_trylock_spinning()
+    - tty: serial: imx: Fix broken RS485
+    - x86/asm: Add _ASM_RIP() macro for x86-64 (%rip) suffix
+    - x86/bugs: Add asm helpers for executing VERW
+    - x86/entry_64: Add VERW just before userspace transition
+    - x86/entry_32: Add VERW just before userspace transition
+    - x86/bugs: Use ALTERNATIVE() instead of mds_user_clear static key
+    - KVM/VMX: Use BT+JNC, i.e. EFLAGS.CF to select VMRESUME vs. VMLAUNCH
+    - KVM/VMX: Move VERW closer to VMentry for MDS mitigation
+    - x86/mmio: Disable KVM mitigation when X86_FEATURE_CLEAR_CPU_BUF is set
+    - Documentation/hw-vuln: Add documentation for RFDS
+    - x86/rfds: Mitigate Register File Data Sampling (RFDS)
+    - [Config] updateconfigs for MITIGATION_RFDS
+    - KVM/x86: Export RFDS_NO and RFDS_CLEAR to guests
+    - arch: Introduce CONFIG_FUNCTION_ALIGNMENT
+    - [Config] updateconfigs for FUNCTION_ALIGNMENT
+    - x86/asm: Differentiate between code and function alignment
+    - x86/alternatives: Introduce int3_emulate_jcc()
+    - x86/alternatives: Teach text_poke_bp() to patch Jcc.d32 instructions
+    - x86/static_call: Add support for Jcc tail-calls
+    - fsnotify: pass data_type to fsnotify_name()
+    - fsnotify: pass dentry instead of inode data
+    - fsnotify: clarify contract for create event hooks
+    - fsnotify: Don't insert unmergeable events in hashtable
+    - fanotify: Fold event size calculation to its own function
+    - fanotify: Split fsid check from other fid mode checks
+    - inotify: Don't force FS_IN_IGNORED
+    - fsnotify: Add helper to detect overflow_event
+    - fsnotify: Add wrapper around fsnotify_add_event
+    - fsnotify: Retrieve super block from the data field
+    - fsnotify: Protect fsnotify_handle_inode_event from no-inode events
+    - fsnotify: Pass group argument to free_event
+    - fanotify: Support null inode event in fanotify_dfid_inode
+    - fanotify: Allow file handle encoding for unhashed events
+    - fanotify: Encode empty file handle when no inode is provided
+    - fanotify: Require fid_mode for any non-fd event
+    - fsnotify: Support FS_ERROR event type
+    - fanotify: Reserve UAPI bits for FAN_FS_ERROR
+    - fanotify: Pre-allocate pool of error events
+    - fanotify: Support enqueueing of error events
+    - fanotify: Support merging of error events
+    - fanotify: Wrap object_fh inline space in a creator macro
+    - fanotify: Add helpers to decide whether to report FID/DFID
+    - fanotify: WARN_ON against too large file handles
+    - fanotify: Report fid info for file related file system errors
+    - fanotify: Emit generic error info for error event
+    - fanotify: Allow users to request FAN_FS_ERROR events
+    - ext4: Send notifications on error
+    - docs: Document the FAN_FS_ERROR event
+    - NFS: Remove unnecessary TRACE_DEFINE_ENUM()s
+    - SUNRPC: Tracepoints should display tk_pid and cl_clid as a fixed-size field
+    - NFS: Move generic FS show macros to global header
+    - NFS: Move NFS protocol display macros to global header
+    - NFSD: Optimize DRC bucket pruning
+    - NFSD: move filehandle format declarations out of "uapi".
+    - NFSD: drop support for ancient filehandles
+    - NFSD: simplify struct nfsfh
+    - NFSD: Initialize pointer ni with NULL and not plain integer 0
+    - SUNRPC: Replace the "__be32 *p" parameter to .pc_decode
+    - SUNRPC: Change return value type of .pc_decode
+    - NFSD: Save location of NFSv4 COMPOUND status
+    - SUNRPC: Replace the "__be32 *p" parameter to .pc_encode
+    - SUNRPC: Change return value type of .pc_encode
+    - nfsd: update create verifier comment
+    - NFSD:fix boolreturn.cocci warning
+    - nfsd4: remove obselete comment
+    - ext4: fix error code saved on super block during file system abort
+    - fsnotify: clarify object type argument
+    - fsnotify: separate mark iterator type from object type enum
+    - fanotify: introduce group flag FAN_REPORT_TARGET_FID
+    - fsnotify: generate FS_RENAME event with rich information
+    - fanotify: use macros to get the offset to fanotify_info buffer
+    - fanotify: use helpers to parcel fanotify_info buffer
+    - fanotify: support secondary dir fh and name in fanotify_info
+    - fanotify: record old and new parent and name in FAN_RENAME event
+    - fanotify: record either old name new name or both for FAN_RENAME
+    - fanotify: report old and/or new parent+name in FAN_RENAME event
+    - fanotify: wire up FAN_RENAME event
+    - exit: Implement kthread_exit
+    - exit: Rename module_put_and_exit to module_put_and_kthread_exit
+    - NFSD: handle errors better in write_ports_addfd()
+    - SUNRPC: change svc_get() to return the svc.
+    - SUNRPC/NFSD: clean up get/put functions.
+    - SUNRPC: stop using ->sv_nrthreads as a refcount
+    - nfsd: make nfsd_stats.th_cnt atomic_t
+    - SUNRPC: use sv_lock to protect updates to sv_nrthreads.
+    - NFSD: narrow nfsd_mutex protection in nfsd thread
+    - NFSD: Make it possible to use svc_set_num_threads_sync
+    - SUNRPC: discard svo_setup and rename svc_set_num_threads_sync()
+    - NFSD: simplify locking for network notifier.
+    - lockd: introduce nlmsvc_serv
+    - lockd: simplify management of network status notifiers
+    - lockd: move lockd_start_svc() call into lockd_create_svc()
+    - lockd: move svc_exit_thread() into the thread
+    - lockd: introduce lockd_put()
+    - lockd: rename lockd_create_svc() to lockd_get()
+    - SUNRPC: move the pool_map definitions (back) into svc.c
+    - SUNRPC: always treat sv_nrpools==1 as "not pooled"
+    - lockd: use svc_set_num_threads() for thread start and stop
+    - NFS: switch the callback service back to non-pooled.
+    - NFSD: Remove be32_to_cpu() from DRC hash function
+    - NFSD: Fix inconsistent indenting
+    - NFSD: simplify per-net file cache management
+    - NFSD: Combine XDR error tracepoints
+    - nfsd: improve stateid access bitmask documentation
+    - NFSD: De-duplicate nfsd4_decode_bitmap4()
+    - nfs: block notification on fs with its own ->lock
+    - nfsd4: add refcount for nfsd4_blocked_lock
+    - nfsd: map EBADF
+    - nfsd: Add errno mapping for EREMOTEIO
+    - nfsd: Retry once in nfsd_open on an -EOPENSTALE return
+    - NFSD: Clean up nfsd_vfs_write()
+    - NFSD: De-duplicate net_generic(SVC_NET(rqstp), nfsd_net_id)
+    - nfsd: Add a tracepoint for errors in nfsd4_clone_file_range()
+    - NFSD: Write verifier might go backwards
+    - NFSD: Clean up the nfsd_net::nfssvc_boot field
+    - NFSD: Rename boot verifier functions
+    - NFSD: Trace boot verifier resets
+    - NFSD: Move fill_pre_wcc() and fill_post_wcc()
+    - fsnotify: invalidate dcache before IN_DELETE event
+    - NFSD: Deprecate NFS_OFFSET_MAX
+    - nfsd: Add support for the birth time attribute
+    - orDate: Thu Sep 30 19:19:57 2021 -0400
+    - NFSD: Skip extra computation for RC_NOCACHE case
+    - NFSD: Streamline the rare "found" case
+    - NFSD: Remove NFSD_PROC_ARGS_* macros
+    - SUNRPC: Remove the .svo_enqueue_xprt method
+    - SUNRPC: Merge svc_do_enqueue_xprt() into svc_enqueue_xprt()
+    - SUNRPC: Remove svo_shutdown method
+    - SUNRPC: Rename svc_create_xprt()
+    - SUNRPC: Rename svc_close_xprt()
+    - SUNRPC: Remove svc_shutdown_net()
+    - NFSD: Remove svc_serv_ops::svo_module
+    - NFSD: Move svc_serv_ops::svo_function into struct svc_serv
+    - NFSD: Remove CONFIG_NFSD_V3
+    - [Config] updateconfigs for NFSD_V3
+    - NFSD: Clean up _lm_ operation names
+    - nfsd: fix using the correct variable for sizeof()
+    - fsnotify: fix merge with parent's ignored mask
+    - fsnotify: optimize FS_MODIFY events with no ignored masks
+    - fsnotify: remove redundant parameter judgment
+    - nfsd: Fix a write performance regression
+    - nfsd: Clean up nfsd_file_put()
+    - fanotify: do not allow setting dirent events in mask of non-dir
+    - fs/lock: documentation cleanup. Replace inode->i_lock with flc_lock.
+    - inotify: move control flags from mask to mark flags
+    - fsnotify: pass flags argument to fsnotify_alloc_group()
+    - fsnotify: make allow_dups a property of the group
+    - fsnotify: create helpers for group mark_mutex lock
+    - inotify: use fsnotify group lock helpers
+    - nfsd: use fsnotify group lock helpers
+    - dnotify: use fsnotify group lock helpers
+    - fsnotify: allow adding an inode mark without pinning inode
+    - fanotify: create helper fanotify_mark_user_flags()
+    - fanotify: factor out helper fanotify_mark_update_flags()
+    - fanotify: implement "evictable" inode marks
+    - fanotify: use fsnotify group lock helpers
+    - fanotify: enable "evictable" inode marks
+    - fsnotify: introduce mark type iterator
+    - fsnotify: consistent behavior for parent not watching children
+    - fanotify: fix incorrect fmode_t casts
+    - NFSD: Clean up nfsd_splice_actor()
+    - NFSD: add courteous server support for thread with only delegation
+    - NFSD: add support for share reservation conflict to courteous server
+    - NFSD: move create/destroy of laundry_wq to init_nfsd and exit_nfsd
+    - fs/lock: add helper locks_owner_has_blockers to check for blockers
+    - fs/lock: add 2 callbacks to lock_manager_operations to resolve conflict
+    - NFSD: add support for lock conflict to courteous server
+    - NFSD: Show state of courtesy client in client info
+    - NFSD: Clean up nfsd3_proc_create()
+    - NFSD: Avoid calling fh_drop_write() twice in do_nfsd_create()
+    - NFSD: Refactor nfsd_create_setattr()
+    - NFSD: Refactor NFSv3 CREATE
+    - NFSD: Refactor NFSv4 OPEN(CREATE)
+    - NFSD: Remove do_nfsd_create()
+    - NFSD: Clean up nfsd_open_verified()
+    - NFSD: Instantiate a struct file when creating a regular NFSv4 file
+    - NFSD: Remove dprintk call sites from tail of nfsd4_open()
+    - NFSD: Fix whitespace
+    - NFSD: Move documenting comment for nfsd4_process_open2()
+    - NFSD: Trace filecache opens
+    - SUNRPC: Use RMW bitops in single-threaded hot paths
+    - nfsd: Unregister the cld notifier when laundry_wq create failed
+    - nfsd: Fix null-ptr-deref in nfsd_fill_super()
+    - NFSD: Modernize nfsd4_release_lockowner()
+    - NFSD: Add documenting comment for nfsd4_release_lockowner()
+    - NFSD: nfsd_file_put() can sleep
+    - NFSD: Fix potential use-after-free in nfsd_file_put()
+    - NFS: restore module put when manager exits.
+    - fanotify: refine the validation checks on non-dir inode mask
+    - NFSD: Decode NFSv4 birth time attribute
+    - fs: inotify: Fix typo in inotify comment
+    - fanotify: prepare for setting event flags in ignore mask
+    - fanotify: cleanups for fanotify_mark() input validations
+    - fanotify: introduce FAN_MARK_IGNORE
+    - fsnotify: Fix comment typo
+    - NLM: Defend against file_lock changes after vfs_test_lock()
+    - NFSD: Instrument fh_verify()
+    - NFSD: Fix space and spelling mistake
+    - nfsd: remove redundant assignment to variable len
+    - NFSD: Demote a WARN to a pr_warn()
+    - NFSD: Report filecache LRU size
+    - NFSD: Report count of calls to nfsd_file_acquire()
+    - NFSD: Report count of freed filecache items
+    - NFSD: Report average age of filecache items
+    - NFSD: Add nfsd_file_lru_dispose_list() helper
+    - NFSD: Refactor nfsd_file_gc()
+    - NFSD: Refactor nfsd_file_lru_scan()
+    - NFSD: Report the number of items evicted by the LRU walk
+    - NFSD: Record number of flush calls
+    - NFSD: Zero counters when the filecache is re-initialized
+    - NFSD: Hook up the filecache stat file
+    - NFSD: WARN when freeing an item still linked via nf_lru
+    - NFSD: Trace filecache LRU activity
+    - NFSD: Leave open files out of the filecache LRU
+    - NFSD: Fix the filecache LRU shrinker
+    - NFSD: Never call nfsd_file_gc() in foreground paths
+    - NFSD: No longer record nf_hashval in the trace log
+    - NFSD: Remove lockdep assertion from unhash_and_release_locked()
+    - NFSD: nfsd_file_unhash can compute hashval from nf->nf_inode
+    - NFSD: Refactor __nfsd_file_close_inode()
+    - NFSD: nfsd_file_hash_remove can compute hashval
+    - NFSD: Remove nfsd_file::nf_hashval
+    - NFSD: Replace the "init once" mechanism
+    - NFSD: Set up an rhashtable for the filecache
+    - NFSD: Convert the filecache to use rhashtable
+    - NFSD: Clean up unused code after rhashtable conversion
+    - NFSD: Separate tracepoints for acquire and create
+    - NFSD: Move nfsd_file_trace_alloc() tracepoint
+    - NFSD: NFSv4 CLOSE should release an nfsd_file immediately
+    - NFSD: Ensure nf_inode is never dereferenced
+    - NFSD: refactoring v4 specific code to a helper in nfs4state.c
+    - NFSD: keep track of the number of v4 clients in the system
+    - NFSD: limit the number of v4 clients to 1024 per 1GB of system memory
+    - nfsd: silence extraneous printk on nfsd.ko insertion
+    - NFSD: Optimize nfsd4_encode_operation()
+    - NFSD: Optimize nfsd4_encode_fattr()
+    - NFSD: Clean up SPLICE_OK in nfsd4_encode_read()
+    - NFSD: Add an nfsd4_read::rd_eof field
+    - NFSD: Optimize nfsd4_encode_readv()
+    - NFSD: Simplify starting_len
+    - NFSD: Use xdr_pad_size()
+    - NFSD: Clean up nfsd4_encode_readlink()
+    - NFSD: Fix strncpy() fortify warning
+    - NFSD: nfserrno(-ENOMEM) is nfserr_jukebox
+    - NFSD: Shrink size of struct nfsd4_copy_notify
+    - NFSD: Shrink size of struct nfsd4_copy
+    - NFSD: Reorder the fields in struct nfsd4_op
+    - NFSD: Make nfs4_put_copy() static
+    - NFSD: Replace boolean fields in struct nfsd4_copy
+    - NFSD: Refactor nfsd4_cleanup_inter_ssc() (1/2)
+    - NFSD: Refactor nfsd4_cleanup_inter_ssc() (2/2)
+    - NFSD: Refactor nfsd4_do_copy()
+    - NFSD: Remove kmalloc from nfsd4_do_async_copy()
+    - NFSD: Add nfsd4_send_cb_offload()
+    - NFSD: Move copy offload callback arguments into a separate structure
+    - NFSD: drop fh argument from alloc_init_deleg
+    - NFSD: verify the opened dentry after setting a delegation
+    - NFSD: introduce struct nfsd_attrs
+    - NFSD: set attributes when creating symlinks
+    - NFSD: add security label to struct nfsd_attrs
+    - NFSD: add posix ACLs to struct nfsd_attrs
+    - NFSD: change nfsd_create()/nfsd_symlink() to unlock directory before
+      returning.
+    - NFSD: always drop directory lock in nfsd_unlink()
+    - NFSD: only call fh_unlock() once in nfsd_link()
+    - NFSD: reduce locking in nfsd_lookup()
+    - NFSD: use explicit lock/unlock for directory ops
+    - NFSD: use (un)lock_inode instead of fh_(un)lock for file operations
+    - NFSD: discard fh_locked flag and fh_lock/fh_unlock
+    - NFSD: fix regression with setting ACLs.
+    - nfsd_splice_actor(): handle compound pages
+    - NFSD: move from strlcpy with unused retval to strscpy
+    - lockd: move from strlcpy with unused retval to strscpy
+    - NFSD enforce filehandle check for source file in COPY
+    - NFSD: remove redundant variable status
+    - nfsd: Avoid some useless tests
+    - nfsd: Propagate some error code returned by memdup_user()
+    - NFSD: Increase NFSD_MAX_OPS_PER_COMPOUND
+    - NFSD: drop fname and flen args from nfsd_create_locked()
+    - nfsd: clean up mounted_on_fileid handling
+    - nfsd: remove nfsd4_prepare_cb_recall() declaration
+    - NFSD: Replace dprintk() call site in fh_verify()
+    - NFSD: Trace NFSv4 COMPOUND tags
+    - NFSD: Add tracepoints to report NFSv4 callback completions
+    - NFSD: Add a mechanism to wait for a DELEGRETURN
+    - NFSD: Refactor nfsd_setattr()
+    - NFSD: Make nfsd4_setattr() wait before returning NFS4ERR_DELAY
+    - NFSD: Make nfsd4_rename() wait before returning NFS4ERR_DELAY
+    - NFSD: Make nfsd4_remove() wait before returning NFS4ERR_DELAY
+    - NFSD: keep track of the number of courtesy clients in the system
+    - NFSD: add shrinker to reap courtesy clients on low memory condition
+    - SUNRPC: Parametrize how much of argsize should be zeroed
+    - NFSD: Reduce amount of struct nfsd4_compoundargs that needs clearing
+    - NFSD: Refactor common code out of dirlist helpers
+    - NFSD: Use xdr_inline_decode() to decode NFSv3 symlinks
+    - NFSD: Clean up WRITE arg decoders
+    - NFSD: Clean up nfs4svc_encode_compoundres()
+    - NFSD: Remove unused nfsd4_compoundargs::cachetype field
+    - NFSD: Pack struct nfsd4_compoundres
+    - nfsd: use DEFINE_PROC_SHOW_ATTRIBUTE to define nfsd_proc_ops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define export_features_fops and
+      supported_enctypes_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define client_info_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define nfsd_reply_cache_stats_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define nfsd_file_cache_stats_fops
+    - NFSD: Rename the fields in copy_stateid_t
+    - nfsd: only fill out return pointer on success in nfsd4_lookup_stateid
+    - nfsd: fix comments about spinlock handling with delegations
+    - nfsd: make nfsd4_run_cb a bool return function
+    - nfsd: extra checks when freeing delegation stateids
+    - fs/notify: constify path
+    - fsnotify: remove unused declaration
+    - fanotify: Remove obsoleted fanotify_event_has_path()
+    - nfsd: fix nfsd_file_unhash_and_dispose
+    - nfsd: rework hashtable handling in nfsd_do_file_acquire
+    - NFSD: unregister shrinker when nfsd_init_net() fails
+    - nfsd: ensure we always call fh_verify_error tracepoint
+    - nfsd: fix net-namespace logic in __nfsd_file_cache_purge
+    - nfsd: fix use-after-free in nfsd_file_do_acquire tracepoint
+    - nfsd: put the export reference in nfsd4_verify_deleg_dentry
+    - NFSD: Fix trace_nfsd_fh_verify_err() crasher
+    - NFSD: Fix reads with a non-zero offset that don't end on a page boundary
+    - lockd: use locks_inode_context helper
+    - nfsd: use locks_inode_context helper
+    - NFSD: Simplify READ_PLUS
+    - NFSD: Remove redundant assignment to variable host_err
+    - NFSD: Finish converting the NFSv3 GETACL result encoder
+    - nfsd: ignore requests to disable unsupported versions
+    - nfsd: move nfserrno() to vfs.c
+    - nfsd: allow disabling NFSv2 at compile time
+    - [Config] updateconfigs for NFSD_V2
+    - exportfs: use pr_debug for unreachable debug statements
+    - NFSD: Pass the target nfsd_file to nfsd_commit()
+    - NFSD: Revert "NFSD: NFSv4 CLOSE should release an nfsd_file immediately"
+    - NFSD: Add an NFSD_FILE_GC flag to enable nfsd_file garbage collection
+    - NFSD: Flesh out a documenting comment for filecache.c
+    - NFSD: Clean up nfs4_preprocess_stateid_op() call sites
+    - NFSD: Trace stateids returned via DELEGRETURN
+    - NFSD: Trace delegation revocations
+    - NFSD: Use const pointers as parameters to fh_ helpers
+    - NFSD: Update file_hashtbl() helpers
+    - NFSD: Clean up nfsd4_init_file()
+    - NFSD: Add a nfsd4_file_hash_remove() helper
+    - NFSD: Clean up find_or_add_file()
+    - NFSD: Refactor find_file()
+    - NFSD: Use rhashtable for managing nfs4_file objects
+    - NFSD: Fix licensing header in filecache.c
+    - nfsd: remove the pages_flushed statistic from filecache
+    - nfsd: reorganize filecache.c
+    - filelock: add a new locks_inode_context accessor function
+    - nfsd: fix up the filecache laundrette scheduling
+    - NFSD: Add an nfsd_file_fsync tracepoint
+    - nfsd: return error if nfs4_setacl fails
+    - NFSD: Use struct_size() helper in alloc_session()
+    - lockd: set missing fl_flags field when retrieving args
+    - lockd: ensure we use the correct file descriptor when unlocking
+    - lockd: fix file selection in nlmsvc_cancel_blocked
+    - trace: Relocate event helper files
+    - NFSD: refactoring courtesy_client_reaper to a generic low memory shrinker
+    - NFSD: add support for sending CB_RECALL_ANY
+    - NFSD: add delegation reaper to react to low memory condition
+    - NFSD: add CB_RECALL_ANY tracepoints
+    - NFSD: Use only RQ_DROPME to signal the need to drop a reply
+    - NFSD: Avoid clashing function prototypes
+    - nfsd: rework refcounting in filecache
+    - nfsd: fix handling of cached open files in nfsd4_open codepath
+    - Revert "SUNRPC: Use RMW bitops in single-threaded hot paths"
+    - NFSD: Use set_bit(RQ_DROPME)
+    - NFSD: register/unregister of nfsd-client shrinker at nfsd startup/shutdown
+      time
+    - NFSD: replace delayed_work with work_struct for nfsd_client_shrinker
+    - nfsd: don't free files unconditionally in __nfsd_file_cache_purge
+    - nfsd: don't destroy global nfs4_file table in per-net shutdown
+    - NFSD: enhance inter-server copy cleanup
+    - nfsd: allow nfsd_file_get to sanely handle a NULL pointer
+    - nfsd: clean up potential nfsd_file refcount leaks in COPY codepath
+    - NFSD: fix leaked reference count of nfsd4_ssc_umount_item
+    - nfsd: don't hand out delegation on setuid files being opened for write
+    - NFSD: fix problems with cleanup on errors in nfsd4_copy
+    - nfsd: fix courtesy client with deny mode handling in nfs4_upgrade_open
+    - nfsd: don't fsync nfsd_files on last close
+    - NFSD: copy the whole verifier in nfsd_copy_write_verifier
+    - NFSD: Protect against filesystem freezing
+    - nfsd: don't replace page in rq_pages if it's a continuation of last page
+    - nfsd: call op_release, even when op_func returns an error
+    - nfsd: don't open-code clear_and_wake_up_bit
+    - nfsd: NFSD_FILE_KEY_INODE only needs to find GC'ed entries
+    - nfsd: simplify test_bit return in NFSD_FILE_KEY_FULL comparator
+    - nfsd: don't kill nfsd_files because of lease break error
+    - nfsd: add some comments to nfsd_file_do_acquire
+    - nfsd: don't take/put an extra reference when putting a file
+    - nfsd: update comment over __nfsd_file_cache_purge
+    - nfsd: allow reaping files still under writeback
+    - NFSD: Convert filecache to rhltable
+    - nfsd: simplify the delayed disposal list code
+    - NFSD: Fix problem of COMMIT and NFS4ERR_DELAY in infinite loop
+    - nfsd: make a copy of struct iattr before calling notify_change
+    - nfsd: fix double fget() bug in __write_ports_addfd()
+    - lockd: drop inappropriate svc_get() from locked_get()
+    - NFSD: Add an nfsd4_encode_nfstime4() helper
+    - nfsd: Fix creation time serialization order
+    - nfsd: Simplify code around svc_exit_thread() call in nfsd()
+    - nfsd: separate nfsd_last_thread() from nfsd_put()
+    - Documentation: Add missing documentation for EXPORT_OP flags
+    - NFSD: fix possible oops when nfsd/pool_stats is closed.
+    - nfsd: call nfsd_last_thread() before final nfsd_put()
+    - nfsd: drop the nfsd_put helper
+    - nfsd: fix RELEASE_LOCKOWNER
+    - nfsd: don't take fi_lock in nfsd_break_deleg_cb()
+    - nfsd: don't call locks_release_private() twice concurrently
+    - nfsd: Fix a regression in nfsd_setattr()
+    - perf/core: Fix reentry problem in perf_output_read_group()
+    - efivarfs: Request at most 512 bytes for variable names
+    - powerpc: xor_vmx: Add '-mhard-float' to CFLAGS
+    - selftests: mptcp: diag: return KSFT_FAIL not test_cnt
+    - vfio/pci: Disable auto-enable of exclusive INTx IRQ
+    - vfio/pci: Lock external INTx masking ops
+    - vfio: Introduce interface to flush virqfd inject workqueue
+    - vfio/pci: Create persistent INTx handler
+    - vfio/platform: Create persistent IRQ handlers
+    - vfio/fsl-mc: Block calling interrupt handler without trigger
+    - serial: sc16is7xx: convert from _raw_ to _noinc_ regmap functions for FIFO
+    - mm/migrate: set swap entry values of THP tail pages properly.
+    - init: open /initrd.image with O_LARGEFILE
+    - btrfs: zoned: use zone aware sb location for scrub
+    - wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes
+    - exec: Fix NOMMU linux_binprm::exec in transfer_args_to_stack()
+    - hexagon: vmlinux.lds.S: handle attributes section
+    - mmc: core: Initialize mmc_blk_ioc_data
+    - mmc: core: Avoid negative index with array access
+    - net: ll_temac: platform_get_resource replaced by wrong function
+    - drm/i915/gt: Reset queue_priority_hint on parking
+    - drm/amdgpu: Use drm_mode_copy()
+    - drm/amd/display: Preserve original aspect ratio in create stream
+    - ALSA: sh: aica: reorder cleanup operations to avoid UAF bugs
+    - scsi: core: Fix unremoved procfs host directory regression
+    - staging: vc04_services: changen strncpy() to strscpy_pad()
+    - staging: vc04_services: fix information leak in create_component()
+    - USB: core: Add hub_get() and hub_put() routines
+    - usb: dwc2: host: Fix remote wakeup from hibernation
+    - usb: dwc2: host: Fix hibernation flow
+    - usb: dwc2: host: Fix ISOC flow in DDMA mode
+    - usb: dwc2: gadget: Fix exiting from clock gating
+    - usb: dwc2: gadget: LPM flow fix
+    - usb: udc: remove warning when queue disabled ep
+    - usb: typec: ucsi: Ack unsupported commands
+    - usb: typec: ucsi: Clear UCSI_CCI_RESET_COMPLETE before reset
+    - scsi: qla2xxx: Prevent command send on chip reset
+    - scsi: qla2xxx: Fix N2N stuck connection
+    - scsi: qla2xxx: Split FCE|EFT trace control
+    - scsi: qla2xxx: NVME|FCP prefer flag not being honored
+    - scsi: qla2xxx: Fix command flush on cable pull
+    - scsi: qla2xxx: Fix double free of fcport
+    - scsi: qla2xxx: Change debug message during driver unload
+    - scsi: qla2xxx: Delay I/O Abort on PCI error
+    - x86/cpu: Enable STIBP on AMD if Automatic IBRS is enabled
+    - PCI/DPC: Quirk PIO log size for Intel Ice Lake Root Ports
+    - scsi: lpfc: Correct size for wqe for memset()
+    - USB: core: Fix deadlock in usb_deauthorize_interface()
+    - scsi: usb: Call scsi_done() directly
+    - scsi: usb: Stop using the SCSI pointer
+    - USB: UAS: return ENODEV when submit urbs fail with device not attached
+    - nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet
+    - mlxbf_gige: stop PHY during open() error paths
+    - iwlwifi: mvm: rfi: use kmemdup() to replace kzalloc + memcpy
+    - wifi: iwlwifi: mvm: rfi: fix potential response leaks
+    - ixgbe: avoid sleeping allocation in ixgbe_ipsec_vf_add_sa()
+    - s390/qeth: handle deferred cc1
+    - tcp: properly terminate timers for kernel sockets
+    - ACPICA: debugger: check status of acpi_evaluate_object() in
+      acpi_db_walk_for_fields()
+    - mlxbf_gige: call request_irq() after NAPI initialized
+    - bpf: Protect against int overflow for stack access size
+    - Octeontx2-af: fix pause frame configuration in GMP mode
+    - dm integrity: fix out-of-range warning
+    - r8169: fix issue caused by buggy BIOS on certain boards with RTL8168d
+    - x86/cpufeatures: Add new word for scattered features
+    - x86/cpufeatures: Add CPUID_LNX_5 to track recently added Linux-defined word
+    - arm64: dts: qcom: sc7180-trogdor: mark bluetooth address as broken
+    - Bluetooth: hci_event: set the conn encrypted before conn establishes
+    - Bluetooth: Fix TOCTOU in HCI debugfs implementation
+    - xen-netfront: Add missing skb_mark_for_recycle
+    - net/rds: fix possible cp null dereference
+    - locking/rwsem: Disable preemption while trying for rwsem lock
+    - io_uring: ensure '0' is returned on file registration success
+    - Revert "x86/mm/ident_map: Use gbpages only where full GB page should be
+      mapped."
+    - mm, vmscan: prevent infinite loop for costly GFP_NOIO | __GFP_RETRY_MAYFAIL
+      allocations
+    - thermal: devfreq_cooling: Fix perf state when calculate dfc res_util
+    - KVM: x86: Bail to userspace if emulation of atomic user access faults
+    - KVM: x86: Mark target gfn of emulated atomic instruction as dirty
+    - netfilter: nf_tables: reject new basechain after table flag update
+    - netfilter: nf_tables: flush pending destroy work before exit_net release
+    - netfilter: nf_tables: Fix potential data-race in __nft_flowtable_type_get()
+    - netfilter: validate user input for expected length
+    - vboxsf: Avoid an spurious warning if load_nls_xxx() fails
+    - bpf, sockmap: Prevent lock inversion deadlock in map delete elem
+    - net/sched: act_skbmod: prevent kernel-infoleak
+    - net: stmmac: fix rx queue priority assignment
+    - selftests: net: gro fwd: update vxlan GRO test expectations
+    - erspan: make sure erspan_base_hdr is present in skb->head
+    - selftests: reuseaddr_conflict: add missing new line at the end of the output
+    - ipv6: Fix infinite recursion in fib6_dump_done().
+    - mlxbf_gige: stop interface during shutdown
+    - udp: do not accept non-tunnel GSO skbs landing in a tunnel
+    - udp: do not transition UDP GRO fraglist partial checksums to unnecessary
+    - udp: prevent local UDP tunnel packets from being GROed
+    - octeontx2-af: Fix issue with loading coalesced KPU profiles
+    - octeontx2-pf: check negative error code in otx2_open()
+    - i40e: fix i40e_count_filters() to count only active/new filters
+    - i40e: fix vf may be used uninitialized in this function warning
+    - scsi: qla2xxx: Update manufacturer details
+    - scsi: qla2xxx: Update manufacturer detail
+    - Revert "usb: phy: generic: Get the vbus supply"
+    - i40e: Store the irq number in i40e_q_vector
+    - i40e: Remove _t suffix from enum type names
+    - i40e: Enforce software interrupt during busy-poll exit
+    - net: usb: asix: suspend embedded PHY if external is used
+    - drivers: net: convert to boolean for the mac_managed_pm flag
+    - net: fec: Set mac_managed_pm during probe
+    - net: ravb: Always process TX descriptor ring
+    - ASoC: rt5682-sdw: fix locking sequence
+    - ASoC: rt711-sdca: fix locking sequence
+    - ASoC: rt711-sdw: fix locking sequence
+    - ASoC: ops: Fix wraparound for mask in snd_soc_get_volsw
+    - ata: sata_sx4: fix pdc20621_get_from_dimm() on 64-bit
+    - scsi: mylex: Fix sysfs buffer lengths
+    - ata: sata_mv: Fix PCI device ID table declaration compilation warning
+    - nfsd: hold a lighter-weight client reference over CB_RECALL_ANY
+    - HID: uhid: Use READ_ONCE()/WRITE_ONCE() for ->running
+    - openrisc: Fix pagewalk usage in arch_dma_{clear, set}_uncached
+    - fs/pipe: Fix lockdep false-positive in watchqueue pipe_write()
+    - ALSA: hda/realtek: Update Panasonic CF-SZ6 quirk to support headset with
+      microphone
+    - driver core: Introduce device_link_wait_removal()
+    - of: dynamic: Synchronize of_changeset_destroy() with the devlink removals
+    - x86/mce: Make sure to grab mce_sysfs_mutex in set_bank()
+    - s390/entry: align system call table on 8 bytes
+    - riscv: Fix spurious errors from __get/put_kernel_nofault
+    - riscv: process: Fix kernel gp leakage
+    - x86/bugs: Fix the SRSO mitigation on Zen3/4
+    - x86/retpoline: Do the necessary fixup to the Zen3/4 srso return thunk for
+      !SRSO
+    - mptcp: don't account accept() of non-MPC client as fallback to TCP
+    - mm/secretmem: fix GUP-fast succeeding on secretmem folios
+    - gro: fix ownership transfer
+    - nvme: fix miss command type check
+    - x86: set SPECTRE_BHI_ON as default
+    - Linux 5.15.154
+
+  * CVE-2024-23307
+    - md/raid5: fix atomicity violation in raid5_cache_count
+
+  * CVE-2024-26828
+    - cifs: fix underflow in parse_server_interfaces()
+
+  * CVE-2024-24861
+    - media: xc4000: Fix atomicity violation in xc4000_get_frequency
+
+  * CVE-2024-26642
+    - netfilter: nf_tables: disallow anonymous set with timeout flag
+
+  * CVE-2024-26926
+    - binder: check offset alignment in binder_get_object()
+
+  * CVE-2024-26922
+    - drm/amdgpu: validate the parameters of bo mapping operations more clearly
+
+  * CVE-2023-6039
+    - timers: Silently ignore timers with a NULL function
+
+  * CVE-2024-26924
+    - netfilter: nft_set_pipapo: do not free live element
+
+  * CVE-2024-26643
+    - netfilter: nf_tables: mark set as dead when unbinding anonymous set with
+      timeout
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 07 Jun 2024 15:06:00 +0200
+
+linux (5.15.0-112.122) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-112.122 -proposed tracker (LP: #2065898)
+
+  * CVE-2024-21823
+    - dmanegine: idxd: reformat opcap output to match bitmap_parse() input
+    - dmaengine: idxd: add WQ operation cap restriction support
+    - dmaengine: idxd: add knob for enqcmds retries
+    - VFIO: Add the SPR_DSA and SPR_IAX devices to the denylist
+    - dmaengine: idxd: add a new security check to deal with a hardware erratum
+    - dmaengine: idxd: add a write() method for applications to submit work
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Thu, 23 May 2024 09:20:33 +0200
+
+linux (5.15.0-111.121) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-111.121 -proposed tracker (LP: #2063763)
+
+  * RTL8852BE fw security fail then lost WIFI function during suspend/resume
+    cycle (LP: #2063096)
+    - wifi: rtw89: download firmware with five times retry
+
+  * Mount CIFS fails with Permission denied (LP: #2061986)
+    - cifs: fix ntlmssp auth when there is no key exchange
+
+  * USB stick can't be detected (LP: #2040948)
+    - usb: Disable USB3 LPM at shutdown
+
+  * Jammy update: v5.15.153 upstream stable release (LP: #2063290)
+    - io_uring/unix: drop usage of io_uring socket
+    - io_uring: drop any code related to SCM_RIGHTS
+    - selftests: tls: use exact comparison in recv_partial
+    - ASoC: rt5645: Make LattePanda board DMI match more precise
+    - x86/xen: Add some null pointer checking to smp.c
+    - MIPS: Clear Cause.BD in instruction_pointer_set
+    - HID: multitouch: Add required quirk for Synaptics 0xcddc device
+    - gen_compile_commands: fix invalid escape sequence warning
+    - RDMA/mlx5: Fix fortify source warning while accessing Eth segment
+    - RDMA/mlx5: Relax DEVX access upon modify commands
+    - riscv: dts: sifive: add missing #interrupt-cells to pmic
+    - x86/mm: Move is_vsyscall_vaddr() into asm/vsyscall.h
+    - x86/mm: Disallow vsyscall page read for copy_from_kernel_nofault()
+    - net/iucv: fix the allocation size of iucv_path_table array
+    - parisc/ftrace: add missing CONFIG_DYNAMIC_FTRACE check
+    - block: sed-opal: handle empty atoms when parsing response
+    - dm-verity, dm-crypt: align "struct bvec_iter" correctly
+    - scsi: mpt3sas: Prevent sending diag_reset when the controller is ready
+    - ALSA: hda/realtek - ALC285 reduce pop noise from Headphone port
+    - drm/amdgpu: Enable gpu reset for S3 abort cases on Raven series
+    - Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security
+    - firewire: core: use long bus reset on gap count error
+    - ASoC: Intel: bytcr_rt5640: Add an extra entry for the Chuwi Vi8 tablet
+    - Input: gpio_keys_polled - suppress deferred probe error for gpio
+    - ASoC: wm8962: Enable oscillator if selecting WM8962_FLL_OSC
+    - ASoC: wm8962: Enable both SPKOUTR_ENA and SPKOUTL_ENA in mono mode
+    - ASoC: wm8962: Fix up incorrect error message in wm8962_set_fll
+    - do_sys_name_to_handle(): use kzalloc() to fix kernel-infoleak
+    - s390/dasd: put block allocation in separate function
+    - s390/dasd: add query PPRC function
+    - s390/dasd: add copy pair setup
+    - s390/dasd: add autoquiesce feature
+    - s390/dasd: Use dev_*() for device log messages
+    - s390/dasd: fix double module refcount decrement
+    - fs/select: rework stack allocation hack for clang
+    - md: Don't clear MD_CLOSING when the raid is about to stop
+    - lib/cmdline: Fix an invalid format specifier in an assertion msg
+    - time: test: Fix incorrect format specifier
+    - rtc: test: Fix invalid format specifier.
+    - aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts
+    - timekeeping: Fix cross-timestamp interpolation on counter wrap
+    - timekeeping: Fix cross-timestamp interpolation corner case decision
+    - timekeeping: Fix cross-timestamp interpolation for non-x86
+    - sched/fair: Take the scheduling domain into account in select_idle_core()
+    - wifi: ath10k: fix NULL pointer dereference in
+      ath10k_wmi_tlv_op_pull_mgmt_tx_compl_ev()
+    - wifi: b43: Stop/wake correct queue in DMA Tx path when QoS is disabled
+    - wifi: b43: Stop/wake correct queue in PIO Tx path when QoS is disabled
+    - wifi: b43: Stop correct queue in DMA worker when QoS is disabled
+    - wifi: b43: Disable QoS for bcm4331
+    - wifi: wilc1000: fix declarations ordering
+    - wifi: wilc1000: fix RCU usage in connect path
+    - wifi: rtl8xxxu: add cancel_work_sync() for c2hcmd_work
+    - wifi: wilc1000: fix multi-vif management when deleting a vif
+    - wifi: mwifiex: debugfs: Drop unnecessary error check for
+      debugfs_create_dir()
+    - cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
+    - cpufreq: Explicitly include correct DT includes
+    - cpufreq: mediatek-hw: Wait for CPU supplies before probing
+    - sock_diag: annotate data-races around sock_diag_handlers[family]
+    - inet_diag: annotate data-races around inet_diag_table[]
+    - bpftool: Silence build warning about calloc()
+    - af_unix: Annotate data-race of gc_in_progress in wait_for_unix_gc().
+    - cpufreq: mediatek-hw: Don't error out if supply is not found
+    - arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM
+    - arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL
+      board
+    - arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD
+      card
+    - arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO
+      voltage
+    - arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL
+      board
+    - wifi: ath9k: delay all of ath9k_wmi_event_tasklet() until init is complete
+    - wifi: iwlwifi: mvm: report beacon protection failures
+    - wifi: iwlwifi: dbg-tlv: ensure NUL termination
+    - wifi: iwlwifi: fix EWRD table validity check
+    - arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
+    - pwm: atmel-hlcdc: Convert to platform remove callback returning void
+    - pwm: atmel-hlcdc: Use consistent variable naming
+    - pwm: atmel-hlcdc: Fix clock imbalance related to suspend support
+    - net: blackhole_dev: fix build warning for ethh set but not used
+    - wifi: libertas: fix some memleaks in lbs_allocate_cmd_buffer()
+    - pwm: sti: Implement .apply() callback
+    - pwm: sti: Fix capture for st,pwm-num-chan < st,capture-num-chan
+    - wifi: iwlwifi: mvm: don't set replay counters to 0xff
+    - s390/vdso: drop '-fPIC' from LDFLAGS
+    - ipv6: mcast: remove one synchronize_net() barrier in ipv6_mc_down()
+    - arm64: dts: mt8183: kukui: Add Type C node
+    - arm64: dts: mt8183: kukui: Split out keyboard node and describe detachables
+    - arm64: dts: mt8183: Move CrosEC base detection node to kukui-based DTs
+    - arm64: dts: mediatek: mt7622: add missing "device_type" to memory nodes
+    - bpf: Mark bpf_spin_{lock,unlock}() helpers with notrace correctly
+    - wireless: Remove redundant 'flush_workqueue()' calls
+    - wifi: wilc1000: prevent use-after-free on vif when cleaning up all
+      interfaces
+    - ACPI: processor_idle: Fix memory leak in acpi_processor_power_exit()
+    - bus: tegra-aconnect: Update dependency to ARCH_TEGRA
+    - [Config]: update CONFIG_TEGRA_ACONNECT
+    - iommu/amd: Mark interrupt as managed
+    - wifi: brcmsmac: avoid function pointer casts
+    - net: ena: Remove ena_select_queue
+    - ARM: dts: arm: realview: Fix development chip ROM compatible value
+    - arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
+    - arm64: dts: renesas: r8a779a0: Correct avb[01] reg sizes
+    - ARM: dts: imx6dl-yapp4: Move phy reset into switch node
+    - ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address
+    - ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node
+    - arm64: dts: marvell: reorder crypto interrupts on Armada SoCs
+    - ACPI: resource: Add Infinity laptops to irq1_edge_low_force_override
+    - ACPI: resource: Do IRQ override on Lunnen Ground laptops
+    - ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override
+    - ACPI: scan: Fix device check notification handling
+    - x86, relocs: Ignore relocations in .notes section
+    - SUNRPC: fix some memleaks in gssx_dec_option_array
+    - mmc: wmt-sdmmc: remove an incorrect release_mem_region() call in the .remove
+      function
+    - wifi: rtw88: 8821c: Fix false alarm count
+    - PCI: Make pci_dev_is_disconnected() helper public for other drivers
+    - iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected
+    - igb: move PEROUT and EXTTS isr logic to separate functions
+    - igb: Fix missing time sync events
+    - Bluetooth: Remove superfluous call to hci_conn_check_pending()
+    - Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855
+    - Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()
+    - Bluetooth: hci_core: Fix possible buffer overflow
+    - sr9800: Add check for usbnet_get_endpoints
+    - bpf: Fix DEVMAP_HASH overflow check on 32-bit arches
+    - bpf: Fix hashtab overflow check on 32-bit arches
+    - bpf: Fix stackmap overflow check on 32-bit arches
+    - ipv6: fib6_rules: flush route cache when rule is changed
+    - net: ip_tunnel: make sure to pull inner header in ip_tunnel_rcv()
+    - net: phy: fix phy_get_internal_delay accessing an empty array
+    - net: hns3: fix kernel crash when 1588 is received on HIP08 devices
+    - net: hns3: fix port duplex configure error in IMP reset
+    - net: phy: DP83822: enable rgmii mode if phy_interface_is_rgmii
+    - net: phy: dp83822: Fix RGMII TX delay configuration
+    - OPP: debugfs: Fix warning around icc_get_name()
+    - tcp: fix incorrect parameter validation in the do_tcp_getsockopt() function
+    - net: Change sock_getsockopt() to take the sk ptr instead of the sock ptr
+    - bpf: net: Change sk_getsockopt() to take the sockptr_t argument
+    - bpf: net: Change do_ip_getsockopt() to take the sockptr_t argument
+    - ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt()
+      function
+    - l2tp: fix incorrect parameter validation in the pppol2tp_getsockopt()
+      function
+    - udp: fix incorrect parameter validation in the udp_lib_getsockopt() function
+    - net: kcm: fix incorrect parameter validation in the kcm_getsockopt) function
+    - net/x25: fix incorrect parameter validation in the x25_getsockopt() function
+    - nfp: flower: handle acti_netdevs allocation failure
+    - dm raid: fix false positive for requeue needed during reshape
+    - dm: call the resume method on internal suspend
+    - drm/tegra: dsi: Add missing check for of_find_device_by_node
+    - drm/tegra: dpaux: Populate AUX bus
+    - drm/tegra: dpaux: Fix PM disable depth imbalance in tegra_dpaux_probe
+    - drm/tegra: dsi: Make use of the helper function dev_err_probe()
+    - drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()
+    - drm/tegra: dsi: Fix missing pm_runtime_disable() in the error handling path
+      of tegra_dsi_probe()
+    - drm/tegra: dc: rgb: Allow changing PLLD rate on Tegra30+
+    - drm/tegra: rgb: Fix some error handling paths in tegra_dc_rgb_probe()
+    - drm/tegra: rgb: Fix missing clk_put() in the error handling paths of
+      tegra_dc_rgb_probe()
+    - drm/tegra: output: Fix missing i2c_put_adapter() in the error handling paths
+      of tegra_output_probe()
+    - drm/rockchip: inno_hdmi: Fix video timing
+    - drm: Don't treat 0 as -1 in drm_fixp2int_ceil
+    - drm/ttm: add ttm_resource_fini v2
+    - drm/vmwgfx: fix a memleak in vmw_gmrid_man_get_node
+    - drm/rockchip: lvds: do not overwrite error code
+    - drm/rockchip: lvds: do not print scary message when probing defer
+    - drm/lima: fix a memleak in lima_heap_alloc
+    - dmaengine: tegra210-adma: Update dependency to ARCH_TEGRA
+    - [Config]: update CONFIG_TEGRA210_ADMA
+    - media: tc358743: register v4l2 async device only after successful setup
+    - PCI/DPC: Print all TLP Prefixes, not just the first
+    - perf record: Fix possible incorrect free in record__switch_output()
+    - HID: lenovo: Add middleclick_workaround sysfs knob for cptkbd
+    - drm/amd/display: Fix a potential buffer overflow in 'dp_dsc_clock_en_read()'
+    - drm/amd/display: Fix potential NULL pointer dereferences in
+      'dcn10_set_output_transfer_func()'
+    - perf evsel: Fix duplicate initialization of data->id in
+      evsel__parse_sample()
+    - clk: meson: Add missing clocks to axg_clk_regmaps
+    - media: em28xx: annotate unchecked call to media_device_register()
+    - media: v4l2-tpg: fix some memleaks in tpg_alloc
+    - media: v4l2-mem2mem: fix a memleak in v4l2_m2m_register_entity
+    - media: edia: dvbdev: fix a use-after-free
+    - pinctrl: mediatek: Drop bogus slew rate register range for MT8192
+    - clk: qcom: reset: Commonize the de/assert functions
+    - clk: qcom: reset: Ensure write completion on reset de/assertion
+    - quota: simplify drop_dquot_ref()
+    - quota: Fix potential NULL pointer dereference
+    - quota: Fix rcu annotations of inode dquot pointers
+    - PCI/P2PDMA: Fix a sleeping issue in a RCU read section
+    - PCI: switchtec: Fix an error handling path in switchtec_pci_probe()
+    - crypto: xilinx - call finalize with bh disabled
+    - perf thread_map: Free strlist on normal path in thread_map__new_by_tid_str()
+    - drm/radeon/ni: Fix wrong firmware size logging in ni_init_microcode()
+    - ALSA: seq: fix function cast warnings
+    - perf stat: Avoid metric-only segv
+    - ASoC: meson: Use dev_err_probe() helper
+    - ASoC: meson: aiu: fix function pointer type mismatch
+    - ASoC: meson: t9015: fix function pointer type mismatch
+    - powerpc: Force inlining of arch_vmap_p{u/m}d_supported()
+    - PCI: endpoint: Support NTB transfer between RC and EP
+    - [Config]: update CONFIG_PCI_EPF_VNTB
+    - NTB: EPF: fix possible memory leak in pci_vntb_probe()
+    - NTB: fix possible name leak in ntb_register_device()
+    - media: sun8i-di: Fix coefficient writes
+    - media: sun8i-di: Fix power on/off sequences
+    - media: sun8i-di: Fix chroma difference threshold
+    - media: imx: csc/scaler: fix v4l2_ctrl_handler memory leak
+    - media: go7007: add check of return value of go7007_read_addr()
+    - media: pvrusb2: remove redundant NULL check
+    - media: pvrusb2: fix pvr2_stream_callback casts
+    - clk: qcom: dispcc-sdm845: Adjust internal GDSC wait times
+    - drm/mediatek: dsi: Fix DSI RGB666 formats and definitions
+    - PCI: Mark 3ware-9650SE Root Port Extended Tags as broken
+    - clk: hisilicon: hi3519: Release the correct number of gates in
+      hi3519_clk_unregister()
+    - clk: hisilicon: hi3559a: Fix an erroneous devm_kfree()
+    - drm/tegra: put drm_gem_object ref on error in tegra_fb_create
+    - mfd: syscon: Call of_node_put() only when of_parse_phandle() takes a ref
+    - mfd: altera-sysmgr: Call of_node_put() only when of_parse_phandle() takes a
+      ref
+    - crypto: arm/sha - fix function cast warnings
+    - drm/tidss: Fix initial plane zpos values
+    - mtd: maps: physmap-core: fix flash size larger than 32-bit
+    - mtd: rawnand: lpc32xx_mlc: fix irq handler prototype
+    - ASoC: meson: axg-tdm-interface: fix mclk setup without mclk-fs
+    - ASoC: meson: axg-tdm-interface: add frame rate constraint
+    - HID: amd_sfh: Update HPD sensor structure elements
+    - drm/amdgpu: Fix missing break in ATOM_ARG_IMM Case of atom_get_src_int()
+    - media: pvrusb2: fix uaf in pvr2_context_set_notify
+    - media: dvb-frontends: avoid stack overflow warnings with clang
+    - media: go7007: fix a memleak in go7007_load_encoder
+    - media: ttpci: fix two memleaks in budget_av_attach
+    - media: mediatek: vcodec: avoid -Wcast-function-type-strict warning
+    - drm/mediatek: Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
+    - powerpc/hv-gpci: Fix the H_GET_PERF_COUNTER_INFO hcall return value checks
+    - drm/msm/dpu: add division of drm_display_mode's hskew parameter
+    - module: Add support for default value for module async_probe
+    - modules: wait do_free_init correctly
+    - powerpc/embedded6xx: Fix no previous prototype for avr_uart_send() etc.
+    - leds: aw2013: Unlock mutex before destroying it
+    - leds: sgm3140: Add missing timer cleanup and flash gpio control
+    - backlight: lm3630a: Initialize backlight_properties on init
+    - backlight: lm3630a: Don't set bl->props.brightness in get_brightness
+    - backlight: da9052: Fully initialize backlight_properties during probe
+    - backlight: lm3639: Fully initialize backlight_properties during probe
+    - backlight: lp8788: Fully initialize backlight_properties during probe
+    - sparc32: Fix section mismatch in leon_pci_grpci
+    - clk: Fix clk_core_get NULL dereference
+    - clk: zynq: Prevent null pointer dereference caused by kmalloc failure
+    - ALSA: hda/realtek: fix ALC285 issues on HP Envy x360 laptops
+    - ALSA: usb-audio: Stop parsing channels bits when all channels are found.
+    - RDMA/srpt: Do not register event handler until srpt device is fully setup
+    - f2fs: multidevice: support direct IO
+    - f2fs: invalidate META_MAPPING before IPU/DIO write
+    - f2fs: replace congestion_wait() calls with io_schedule_timeout()
+    - f2fs: fix to invalidate META_MAPPING before DIO write
+    - f2fs: invalidate meta pages only for post_read required inode
+    - f2fs: reduce stack memory cost by using bitfield in struct f2fs_io_info
+    - f2fs: compress: fix to cover normal cluster write with cp_rwsem
+    - f2fs: compress: fix to check unreleased compressed cluster
+    - scsi: csiostor: Avoid function pointer casts
+    - RDMA/device: Fix a race between mad_client and cm_client init
+    - RDMA/rtrs-clt: Check strnlen return len in sysfs mpath_policy_store()
+    - scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
+    - net: sunrpc: Fix an off by one in rpc_sockaddr2uaddr()
+    - NFSv4.2: fix nfs4_listxattr kernel BUG at mm/usercopy.c:102
+    - NFSv4.2: fix listxattr maximum XDR buffer size
+    - watchdog: stm32_iwdg: initialize default timeout
+    - NFS: Fix an off by one in root_nfs_cat()
+    - f2fs: compress: fix reserve_cblocks counting error when out of space
+    - afs: Revert "afs: Hide silly-rename files from userspace"
+    - comedi: comedi_test: Prevent timers rescheduling during deletion
+    - remoteproc: stm32: use correct format strings on 64-bit
+    - remoteproc: stm32: Fix incorrect type in assignment for va
+    - remoteproc: stm32: Fix incorrect type assignment returned by
+      stm32_rproc_get_loaded_rsc_tablef
+    - tty: vt: fix 20 vs 0x20 typo in EScsiignore
+    - serial: max310x: fix syntax error in IRQ error message
+    - tty: serial: samsung: fix tx_empty() to return TIOCSER_TEMT
+    - arm64: dts: broadcom: bcmbca: bcm4908: drop invalid switch cells
+    - kconfig: fix infinite loop when expanding a macro at the end of file
+    - rtc: mt6397: select IRQ_DOMAIN instead of depending on it
+    - serial: 8250_exar: Don't remove GPIO device on suspend
+    - staging: greybus: fix get_channel_from_mode() failure path
+    - usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
+    - io_uring: don't save/restore iowait state
+    - nouveau: reset the bo resource bus info after an eviction
+    - octeontx2-af: Use matching wake_up API variant in CGX command interface
+    - s390/vtime: fix average steal time calculation
+    - soc: fsl: dpio: fix kcalloc() argument order
+    - hsr: Fix uninit-value access in hsr_get_node()
+    - net: mtk_eth_soc: move MAC_MCR setting to mac_finish()
+    - net: mediatek: mtk_eth_soc: clear MAC_MCR_FORCE_LINK only when MAC is up
+    - net: ethernet: mtk_eth_soc: fix PPE hanging issue
+    - packet: annotate data-races around ignore_outgoing
+    - net: veth: do not manipulate GRO when using XDP
+    - net: dsa: mt7530: prevent possible incorrect XTAL frequency selection
+    - vdpa/mlx5: Allow CVQ size changes
+    - wireguard: receive: annotate data-race around receiving_counter.counter
+    - rds: introduce acquire/release ordering in acquire/release_in_xmit()
+    - hsr: Handle failures in module init
+    - net: phy: fix phy_read_poll_timeout argument type in genphy_loopback
+    - net/bnx2x: Prevent access to a freed page in page_pool
+    - octeontx2-af: Use separate handlers for interrupts
+    - netfilter: nf_tables: do not compare internal table flags on updates
+    - rcu: add a helper to report consolidated flavor QS
+    - net: report RCU QS on threaded NAPI repolling
+    - bpf: report RCU QS in cpumap kthread
+    - net: dsa: mt7530: fix handling of LLDP frames
+    - net: dsa: mt7530: fix handling of 802.1X PAE frames
+    - net: dsa: mt7530: fix link-local frames that ingress vlan filtering ports
+    - net: dsa: mt7530: fix handling of all link-local frames
+    - spi: spi-mt65xx: Fix NULL pointer access in interrupt handler
+    - regmap: Add missing map->bus check
+    - remoteproc: stm32: fix incorrect optional pointers
+
+  * Jammy update: v5.15.152 upstream stable release (LP: #2063276)
+    - mmc: mmci: stm32: use a buffer for unaligned DMA requests
+    - mmc: mmci: stm32: fix DMA API overlapping mappings warning
+    - net: lan78xx: fix runtime PM count underflow on link stop
+    - ixgbe: {dis, en}able irqs in ixgbe_txrx_ring_{dis, en}able
+    - i40e: disable NAPI right after disabling irqs when handling xsk_pool
+    - tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string
+    - geneve: make sure to pull inner header in geneve_rx()
+    - net: sparx5: Fix use after free inside sparx5_del_mact_entry
+    - net: ice: Fix potential NULL pointer dereference in ice_bridge_setlink()
+    - net/ipv6: avoid possible UAF in ip6_route_mpath_notify()
+    - cpumap: Zero-initialise xdp_rxq_info struct before running XDP program
+    - net/rds: fix WARNING in rds_conn_connect_if_down
+    - netfilter: nft_ct: fix l3num expectations with inet pseudo family
+    - netfilter: nf_conntrack_h323: Add protection for bmp length out of range
+    - erofs: apply proper VMA alignment for memory mapped files on THP
+    - netrom: Fix a data-race around sysctl_netrom_default_path_quality
+    - netrom: Fix a data-race around sysctl_netrom_obsolescence_count_initialiser
+    - netrom: Fix data-races around sysctl_netrom_network_ttl_initialiser
+    - netrom: Fix a data-race around sysctl_netrom_transport_timeout
+    - netrom: Fix a data-race around sysctl_netrom_transport_maximum_tries
+    - netrom: Fix a data-race around sysctl_netrom_transport_acknowledge_delay
+    - netrom: Fix a data-race around sysctl_netrom_transport_busy_delay
+    - netrom: Fix a data-race around sysctl_netrom_transport_requested_window_size
+    - netrom: Fix a data-race around sysctl_netrom_transport_no_activity_timeout
+    - netrom: Fix a data-race around sysctl_netrom_routing_control
+    - netrom: Fix a data-race around sysctl_netrom_link_fails_count
+    - netrom: Fix data-races around sysctl_net_busy_read
+    - ALSA: usb-audio: Refcount multiple accesses on the single clock
+    - ALSA: usb-audio: Clear fixed clock rate at closing EP
+    - ALSA: usb-audio: Split endpoint setups for hw_params and prepare (take#2)
+    - ALSA: usb-audio: Properly refcounting clock rate
+    - ALSA: usb-audio: Apply mutex around snd_usb_endpoint_set_params()
+    - ALSA: usb-audio: Correct the return code from snd_usb_endpoint_set_params()
+    - ALSA: usb-audio: Avoid superfluous endpoint setup
+    - ALSA: usb-audio: Add quirk for Tascam Model 12
+    - ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
+    - ALSA: usb-audio: Fix microphone sound on Nexigo webcam.
+    - ALSA: usb-audio: add quirk for RODE NT-USB+
+    - drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd()
+      & write_dpcd()' functions
+    - nfp: flower: add goto_chain_index for ct entry
+    - nfp: flower: add hardware offload check for post ct entry
+    - selftests/mm: switch to bash from sh
+    - selftests: mm: fix map_hugetlb failure on 64K page size systems
+    - xhci: process isoc TD properly when there was a transaction error mid TD.
+    - xhci: handle isoc Babble and Buffer Overrun events properly
+    - serial: max310x: use regmap methods for SPI batch operations
+    - serial: max310x: use a separate regmap for each port
+    - serial: max310x: prevent infinite while() loop in port startup
+    - drm/amd/pm: do not expose the API used internally only in kv_dpm.c
+    - drm/amdgpu: Reset IH OVERFLOW_CLEAR bit
+    - selftests: mptcp: decrease BW in simult flows
+    - hv_netvsc: use netif_is_bond_master() instead of open code
+    - hv_netvsc: Register VF in netvsc_probe if NET_DEVICE_REGISTER missed
+    - drm/amd/display: Re-arrange FPU code structure for dcn2x
+    - drm/amd/display: move calcs folder into DML
+    - drm/amd/display: remove DML Makefile duplicate lines
+    - drm/amd/display: Increase frame-larger-than for all display_mode_vba files
+    - getrusage: add the "signal_struct *sig" local variable
+    - getrusage: move thread_group_cputime_adjusted() outside of
+      lock_task_sighand()
+    - getrusage: use __for_each_thread()
+    - getrusage: use sig->stats_lock rather than lock_task_sighand()
+    - proc: Use task_is_running() for wchan in /proc/$pid/stat
+    - fs/proc: do_task_stat: move thread_group_cputime_adjusted() outside of
+      lock_task_sighand()
+    - ALSA: usb-audio: Fix wrong kfree issue in snd_usb_endpoint_free_all
+    - ALSA: usb-audio: Always initialize fixed_rate in
+      snd_usb_find_implicit_fb_sync_format()
+    - ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
+    - ALSA: usb-audio: Sort quirk table entries
+    - regmap: allow to define reg_update_bits for no bus configuration
+    - regmap: Add bulk read/write callbacks into regmap_config
+    - serial: max310x: make accessing revision id interface-agnostic
+    - serial: max310x: fix IO data corruption in batched operations
+    - Linux 5.15.152
+
+  * CVE-2024-26809
+    - netfilter: nft_set_pipapo: release elements in clone only from destroy path
+
+  * CVE-2024-26792
+    - btrfs: fix double free of anonymous device after snapshot creation failure
+
+  * CVE-2023-52530
+    - wifi: mac80211: fix potential key use-after-free
+
+  * CVE-2023-52447
+    - bpf: Defer the free of inner map when necessary
+    - rcu-tasks: Provide rcu_trace_implies_rcu_gp()
+
+  * Avoid creating non-working backlight sysfs knob from ASUS board
+    (LP: #2060422)
+    - platform/x86: asus-wmi: Consider device is absent when the read is ~0
+
+  * [Ubuntu 22.04.4/linux-image-6.5.0-26-generic] Kernel output "UBSAN: array-
+    index-out-of-bounds in /build/linux-hwe-6.5-34pCLi/linux-
+    hwe-6.5-6.5.0/drivers/net/hyperv/netvsc.c:1445:41" multiple times,
+    especially during boot. (LP: #2058477)
+    - hv: hyperv.h: Replace one-element array with flexible-array member
+
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209)
+    - netfilter: nf_tables: disallow timeout for anonymous sets
+    - mtd: spinand: gigadevice: Fix the get ecc status issue
+    - netlink: Fix kernel-infoleak-after-free in __skb_datagram_iter
+    - net: ip_tunnel: prevent perpetual headroom growth
+    - tun: Fix xdp_rxq_info's queue_index when detaching
+    - cpufreq: intel_pstate: fix pstate limits enforcement for adjust_perf call
+      back
+    - net: veth: clear GRO when clearing XDP even when down
+    - ipv6: fix potential "struct net" leak in inet6_rtm_getaddr()
+    - lan78xx: enable auto speed configuration for LAN7850 if no EEPROM is
+      detected
+    - net: enable memcg accounting for veth queues
+    - veth: try harder when allocating queue memory
+    - net: usb: dm9601: fix wrong return value in dm9601_mdio_read
+    - uapi: in6: replace temporary label with rfc9486
+    - stmmac: Clear variable when destroying workqueue
+    - Bluetooth: Avoid potential use-after-free in hci_error_reset
+    - Bluetooth: hci_event: Fix wrongly recorded wakeup BD_ADDR
+    - netfilter: nf_tables: allow NFPROTO_INET in nft_(match/target)_validate()
+    - netfilter: nfnetlink_queue: silence bogus compiler warning
+    - netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
+    - netfilter: make function op structures const
+    - netfilter: let reset rules clean out conntrack entries
+    - netfilter: bridge: confirm multicast packets before passing them up the
+      stack
+    - rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
+    - igb: extend PTP timestamp adjustments to i211
+    - efi/capsule-loader: fix incorrect allocation size
+    - power: supply: bq27xxx-i2c: Do not free non existing IRQ
+    - ALSA: Drop leftover snd-rtctimer stuff from Makefile
+    - fbcon: always restore the old font data in fbcon_do_set_font()
+    - afs: Fix endless loop in directory parsing
+    - riscv: Sparse-Memory/vmemmap out-of-bounds fix
+    - ALSA: firewire-lib: fix to check cycle continuity
+    - gtp: fix use-after-free and null-ptr-deref in gtp_newlink()
+    - wifi: nl80211: reject iftype change with mesh ID change
+    - btrfs: dev-replace: properly validate device names
+    - dmaengine: fsl-qdma: fix SoC may hang on 16 byte unaligned read
+    - dmaengine: ptdma: use consistent DMA masks
+    - dmaengine: fsl-qdma: init irq after reg initialization
+    - mmc: core: Fix eMMC initialization with 1-bit bus connection
+    - mmc: sdhci-xenon: add timeout for PHY init complete
+    - mmc: sdhci-xenon: fix PHY init clock stability
+    - pmdomain: qcom: rpmhpd: Fix enabled_corner aggregation
+    - x86/cpu/intel: Detect TME keyid bits before setting MTRR mask registers
+    - mptcp: move __mptcp_error_report in protocol.c
+    - mptcp: process pending subflow error on close
+    - mptcp: rename timer related helper to less confusing names
+    - selftests: mptcp: add missing kconfig for NF Filter
+    - selftests: mptcp: add missing kconfig for NF Filter in v6
+    - mptcp: clean up harmless false expressions
+    - mptcp: add needs_id for netlink appending addr
+    - mptcp: push at DSS boundaries
+    - mptcp: fix possible deadlock in subflow diag
+    - cachefiles: fix memory leak in cachefiles_add_cache()
+    - fs,hugetlb: fix NULL pointer dereference in hugetlbs_fill_super
+    - Revert "drm/bridge: lt8912b: Register and attach our DSI device at probe"
+    - af_unix: Drop oob_skb ref before purging queue in GC.
+    - gpio: 74x164: Enable output pins after registers are reset
+    - gpiolib: Fix the error path order in gpiochip_add_data_with_key()
+    - gpio: fix resource unwinding order in error path
+    - Revert "interconnect: Fix locking for runpm vs reclaim"
+    - Revert "interconnect: Teach lockdep about icc_bw_lock order"
+    - bpf: Add BPF_FIB_LOOKUP_SKIP_NEIGH for bpf_fib_lookup
+    - bpf: Add table ID to bpf_fib_lookup BPF helper
+    - bpf: Derive source IP addr via bpf_*_fib_lookup()
+    - Linux 5.15.151
+
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209) //
+    CVE-2024-26782
+    - mptcp: fix double-free on socket dismantle
+
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209) // Fix
+    bluetooth connections with 3.0 device (LP: #2063067)
+    - Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
+
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142)
+    - net/sched: Retire CBQ qdisc
+    - [Config] updateconfigs for NET_SCH_CBQ
+    - net/sched: Retire ATM qdisc
+    - [Config] updateconfigs for NET_SCH_ATM
+    - net/sched: Retire dsmark qdisc
+    - [Config] updateconfigs for NET_SCH_DSMARK
+    - smb: client: fix potential OOBs in smb2_parse_contexts()
+    - smb: client: fix parsing of SMB3.1.1 POSIX create context
+    - sched/rt: sysctl_sched_rr_timeslice show default timeslice after reset
+    - PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
+    - bpf: Merge printk and seq_printf VARARG max macros
+    - bpf: Add struct for bin_args arg in bpf_bprintf_prepare
+    - bpf: Do cleanup in bpf_bprintf_cleanup only when needed
+    - bpf: Remove trace_printk_lock
+    - userfaultfd: fix mmap_changing checking in mfill_atomic_hugetlb
+    - zonefs: Improve error handling
+    - x86/fpu: Stop relying on userspace for info to fault in xsave buffer
+    - sched/rt: Fix sysctl_sched_rr_timeslice intial value
+    - sched/rt: Disallow writing invalid values to sched_rt_period_us
+    - scsi: target: core: Add TMF to tmr_list handling
+    - dmaengine: shdma: increase size of 'dev_id'
+    - dmaengine: fsl-qdma: increase size of 'irq_name'
+    - wifi: cfg80211: fix missing interfaces when dumping
+    - wifi: mac80211: fix race condition on enabling fast-xmit
+    - fbdev: savage: Error out if pixclock equals zero
+    - fbdev: sis: Error out if pixclock equals zero
+    - spi: hisi-sfc-v3xx: Return IRQ_NONE if no interrupts were detected
+    - ahci: asm1166: correct count of reported ports
+    - ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers
+    - MIPS: reserve exception vector space ONLY ONCE
+    - platform/x86: touchscreen_dmi: Add info for the TECLAST X16 Plus tablet
+    - ext4: avoid dividing by 0 in mb_update_avg_fragment_size() when block bitmap
+      corrupt
+    - ext4: avoid allocating blocks from corrupted group in
+      ext4_mb_try_best_found()
+    - ext4: avoid allocating blocks from corrupted group in ext4_mb_find_by_goal()
+    - dmaengine: ti: edma: Add some null pointer checks to the edma_probe
+    - regulator: pwm-regulator: Add validity checks in continuous .get_voltage
+    - nvmet-tcp: fix nvme tcp ida memory leak
+    - ALSA: usb-audio: Check presence of valid altsetting control
+    - ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616
+    - spi: sh-msiof: avoid integer overflow in constants
+    - Input: xpad - add Lenovo Legion Go controllers
+    - netfilter: conntrack: check SCTP_CID_SHUTDOWN_ACK for vtag setting in
+      sctp_new
+    - ALSA: usb-audio: Ignore clock selector errors for single connection
+    - nvme-fc: do not wait in vain when unloading module
+    - nvmet-fcloop: swap the list_add_tail arguments
+    - nvmet-fc: release reference on target port
+    - nvmet-fc: defer cleanup using RCU properly
+    - nvmet-fc: hold reference on hostport match
+    - nvmet-fc: abort command when there is no binding
+    - nvmet-fc: avoid deadlock on delete association path
+    - nvmet-fc: take ref count on tgtport before delete assoc
+    - ext4: correct the hole length returned by ext4_map_blocks()
+    - Input: i8042 - add Fujitsu Lifebook U728 to i8042 quirk table
+    - fs/ntfs3: Modified fix directory element type detection
+    - fs/ntfs3: Improve ntfs_dir_count
+    - fs/ntfs3: Correct hard links updating when dealing with DOS names
+    - fs/ntfs3: Print warning while fixing hard links count
+    - fs/ntfs3: Fix detected field-spanning write (size 8) of single field
+      "le->name"
+    - fs/ntfs3: Add NULL ptr dereference checking at the end of
+      attr_allocate_frame()
+    - fs/ntfs3: Disable ATTR_LIST_ENTRY size check
+    - fs/ntfs3: use non-movable memory for ntfs3 MFT buffer cache
+    - fs/ntfs3: Prevent generic message "attempt to access beyond end of device"
+    - fs/ntfs3: Correct function is_rst_area_valid
+    - fs/ntfs3: Update inode->i_size after success write into compressed file
+    - fs/ntfs3: Fix oob in ntfs_listxattr
+    - wifi: mac80211: adding missing drv_mgd_complete_tx() call
+    - efi: runtime: Fix potential overflow of soft-reserved region size
+    - efi: Don't add memblocks for soft-reserved memory
+    - hwmon: (coretemp) Enlarge per package core count limit
+    - scsi: lpfc: Use unsigned type for num_sge
+    - firewire: core: send bus reset promptly on gap count error
+    - drm/amdgpu: skip to program GFXDEC registers for suspend abort
+    - drm/amdgpu: reset gpu for s3 suspend abort case
+    - virtio-blk: Ensure no requests in virtqueues before deleting vqs.
+    - pmdomain: mediatek: fix race conditions with genpd
+    - ksmbd: free aux buffer if ksmbd_iov_pin_rsp_read fails
+    - pmdomain: renesas: r8a77980-sysc: CR7 must be always on
+    - erofs: fix lz4 inplace decompression
+    - IB/hfi1: Fix sdma.h tx->num_descs off-by-one error
+    - drm/ttm: Fix an invalid freeing on already freed page in error path
+    - dm-crypt: don't modify the data when using authenticated encryption
+    - platform/x86: intel-vbtn: Stop calling "VBDL" from notify_handler
+    - platform/x86: touchscreen_dmi: Allow partial (prefix) matches for ACPI names
+    - KVM: arm64: vgic-its: Test for valid IRQ in MOVALL handler
+    - KVM: arm64: vgic-its: Test for valid IRQ in its_sync_lpi_pending_table()
+    - gtp: fix use-after-free and null-ptr-deref in gtp_genl_dump_pdp()
+    - PCI/MSI: Prevent MSI hardware interrupt number truncation
+    - l2tp: pass correct message length to ip6_append_data
+    - ARM: ep93xx: Add terminator to gpiod_lookup_table
+    - Revert "x86/ftrace: Use alternative RET encoding"
+    - x86/text-patching: Make text_gen_insn() play nice with ANNOTATE_NOENDBR
+    - x86/ibt,paravirt: Use text_gen_insn() for paravirt_patch()
+    - x86/ftrace: Use alternative RET encoding
+    - x86/returnthunk: Allow different return thunks
+    - Revert "x86/alternative: Make custom return thunk unconditional"
+    - x86/alternative: Make custom return thunk unconditional
+    - serial: amba-pl011: Fix DMA transmission in RS485 mode
+    - usb: dwc3: gadget: Don't disconnect if not started
+    - usb: cdnsp: blocked some cdns3 specific code
+    - usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
+    - usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
+    - usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
+    - usb: roles: fix NULL pointer issue when put module's reference
+    - usb: roles: don't get/set_role() when usb_role_switch is unregistered
+    - mptcp: fix lockless access in subflow ULP diag
+    - clk: imx: imx8mp: add shared clk gate for usb suspend clk
+    - clk: qcom: gcc-qcs404: disable gpll[04]_out_aux parents
+    - clk: qcom: gcc-qcs404: fix names of the DSI clocks used as parents
+    - mtd: rawnand: sunxi: Fix the size of the last OOB region
+    - RISC-V: fix funct4 definition for c.jalr in parse_asm.h
+    - Input: iqs269a - drop unused device node references
+    - Input: iqs269a - configure device with a single block write
+    - Input: iqs269a - increase interrupt handler return delay
+    - clk: renesas: cpg-mssr: Fix use after free if cpg_mssr_common_init() failed
+    - Input: ads7846 - don't report pressure for ads7845
+    - clk: renesas: cpg-mssr: Remove superfluous check in resume code
+    - clk: imx: avoid memory leak
+    - Input: ads7846 - always set last command to PWRDOWN
+    - Input: ads7846 - don't check penirq immediately for 7845
+    - powerpc/powernv/ioda: Skip unallocated resources when mapping to PE
+    - clk: qcom: gpucc-sc7180: fix clk_dis_wait being programmed for CX GDSC
+    - clk: qcom: gpucc-sdm845: fix clk_dis_wait being programmed for CX GDSC
+    - clk: Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
+    - powerpc/pseries/lparcfg: add missing RTAS retry status handling
+    - powerpc/perf/hv-24x7: add missing RTAS retry status handling
+    - powerpc/pseries/lpar: add missing RTAS retry status handling
+    - MIPS: SMP-CPS: fix build error when HOTPLUG_CPU not set
+    - MIPS: vpe-mt: drop physical_memsize
+    - vdpa/mlx5: Don't clear mr struct on destroy MR
+    - ARM: dts: BCM53573: Drop nonexistent #usb-cells
+    - RDMA/siw: Balance the reference of cep->kref in the error path
+    - RDMA/siw: Correct wrong debug message
+    - clk: linux/clk-provider.h: fix kernel-doc warnings and typos
+    - platform/x86: asus-wmi: Document the dgpu_disable sysfs attribute
+    - acpi: property: Let args be NULL in __acpi_node_get_property_reference
+    - ARM: dts: BCM53573: Drop nonexistent "default-off" LED trigger
+    - tools headers UAPI: Sync linux/fscrypt.h with the kernel sources
+    - perf beauty: Update copy of linux/socket.h with the kernel sources
+    - tools/virtio: fix build
+    - drm/amdgpu: init iommu after amdkfd device init
+    - f2fs: don't set GC_FAILURE_PIN for background GC
+    - f2fs: write checkpoint during FG_GC
+    - drm/i915/dg1: Update DMC_DEBUG3 register
+    - kernel/sched: Remove dl_boosted flag comment
+    - cifs: remove useless parameter 'is_fsctl' from SMB2_ioctl()
+    - serial: 8250: Remove serial_rs485 sanitization from em485
+    - clk: imx8mp: Add DISP2 pixel clock
+    - clk: imx8mp: add clkout1/2 support
+    - dt-bindings: clocks: imx8mp: Add ID for usb suspend clock
+    - net: ethernet: ti: add missing of_node_put before return
+    - powerpc/rtas: make all exports GPL
+    - powerpc/rtas: ensure 4KB alignment for rtas_data_buf
+    - powerpc/eeh: Small refactor of eeh_handle_normal_event()
+    - powerpc/eeh: Set channel state after notifying the drivers
+    - PM: core: Redefine pm_ptr() macro
+    - PM: core: Add new *_PM_OPS macros, deprecate old ones
+    - mmc: jz4740: Use the new PM macros
+    - mmc: mxc: Use the new PM macros
+    - PM: core: Remove static qualifier in DEFINE_SIMPLE_DEV_PM_OPS macro
+    - Input: iqs269a - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
+    - Input: iqs269a - do not poll during suspend or resume
+    - Input: iqs269a - do not poll during ATI
+    - net/sched: Refactor qdisc_graft() for ingress and clsact Qdiscs
+    - netfilter: nf_tables: add rescheduling points during loop detection walks
+    - debugobjects: Recheck debug_objects_enabled before reporting
+    - nbd: Add the maximum limit of allocated index in nbd_dev_add
+    - md: fix data corruption for raid456 when reshape restart while grow up
+    - md/raid10: prevent soft lockup while flush writes
+    - posix-timers: Ensure timer ID search-loop limit is valid
+    - btrfs: add xxhash to fast checksum implementations
+    - ACPI: button: Add lid disable DMI quirk for Nextbook Ares 8A
+    - ACPI: video: Add backlight=native DMI quirk for Apple iMac11,3
+    - ACPI: video: Add backlight=native DMI quirk for Lenovo ThinkPad X131e (3371
+      AMD version)
+    - arm64: set __exception_irq_entry with __irq_entry as a default
+    - arm64: mm: fix VA-range sanity check
+    - sched/fair: Don't balance task to its current running CPU
+    - wifi: ath11k: fix registration of 6Ghz-only phy without the full channel
+      range
+    - bpf: Address KCSAN report on bpf_lru_list
+    - devlink: report devlink_port_type_warn source device
+    - wifi: wext-core: Fix -Wstringop-overflow warning in
+      ioctl_standard_iw_point()
+    - wifi: iwlwifi: mvm: avoid baid size integer overflow
+    - exfat: support dynamic allocate bh for exfat_entry_set_cache
+    - arm64: dts: rockchip: fix regulator name on rk3399-rock-4
+    - arm64: dts: rockchip: add ES8316 codec for ROCK Pi 4
+    - arm64: dts: rockchip: add SPDIF node for ROCK Pi 4
+    - ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
+    - ACPI: video: Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
+    - ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA
+    - ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
+    - ACPI: resource: Skip IRQ override on Asus Expertbook B2402CBA
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1502CBA
+    - xhci: cleanup xhci_hub_control port references
+    - xhci: move port specific items such as state completions to port structure
+    - xhci: rename resume_done to resume_timestamp
+    - xhci: clear usb2 resume related variables in one place.
+    - xhci: decouple usb2 port resume and get_port_status request handling
+    - xhci: track port suspend state correctly in unsuccessful resume cases
+    - cifs: add a warning when the in-flight count goes negative
+    - IB/hfi1: Fix a memleak in init_credit_return
+    - RDMA/bnxt_re: Return error for SRQ resize
+    - RDMA/irdma: Fix KASAN issue with tasklet
+    - RDMA/irdma: Validate max_send_wr and max_recv_wr
+    - RDMA/irdma: Set the CQ read threshold for GEN 1
+    - RDMA/irdma: Add AE for too many RNRS
+    - RDMA/srpt: Support specifying the srpt_service_guid parameter
+    - RDMA/qedr: Fix qedr_create_user_qp error flow
+    - arm64: dts: rockchip: set num-cs property for spi on px30
+    - RDMA/srpt: fix function pointer cast warnings
+    - bpf, scripts: Correct GPL license name
+    - scsi: jazz_esp: Only build if SCSI core is builtin
+    - nouveau: fix function cast warnings
+    - net: stmmac: Fix incorrect dereference in interrupt handlers
+    - ipv4: properly combine dev_base_seq and ipv4.dev_addr_genid
+    - ipv6: properly combine dev_base_seq and ipv6.dev_addr_genid
+    - ata: libahci_platform: Convert to using devm bulk clocks API
+    - ata: libahci_platform: Introduce reset assertion/deassertion methods
+    - ata: ahci_ceva: fix error handling for Xilinx GT PHY support
+    - bpf: Fix racing between bpf_timer_cancel_and_free and bpf_timer_cancel
+    - drm/nouveau/instmem: fix uninitialized_var.cocci warning
+    - octeontx2-af: Consider the action set by PF
+    - s390: use the correct count for __iowrite64_copy()
+    - netfilter: nf_tables: set dormant flag on hook register failure
+    - netfilter: flowtable: simplify route logic
+    - netfilter: nft_flow_offload: reset dst in route object after setting up flow
+    - netfilter: nft_flow_offload: release dst in case direct xmit path is used
+    - drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set
+    - drm/amd/display: Fix memory leak in dm_sw_fini()
+    - i2c: imx: Add timer for handling the stop condition
+    - i2c: imx: when being a target, mark the last read as processed
+    - fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio
+    - netfilter: nf_tables: fix scheduling-while-atomic splat
+    - ext4: regenerate buddy after block freeing failed if under fc replay
+    - ext4: avoid bb_free and bb_fragments inconsistency in mb_free_blocks()
+    - netfilter: nf_tables: can't schedule in nft_chain_validate
+    - r8169: use new PM macros
+    - Linux 5.15.150
+
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26733
+    - packet: move from strlcpy with unused retval to strscpy
+    - net: dev: Convert sa_data to flexible array in struct sockaddr
+    - arp: Prevent overflow in arp_req_get().
+
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26735
+    - ipv6: sr: fix possible use-after-free and null-ptr-deref
+
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26736
+    - afs: Increase buffer size in afs_update_volume_status()
+
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26748
+    - usb: cdns3: fix memory double free when handle zero packet
+
+  * CVE-2023-47233
+    - wifi: brcmfmac: Fix use-after-free bug in brcmf_cfg80211_detach
+
+  * CVE-2024-26584
+    - net: tls: handle backlogging of crypto requests
+
+  * CVE-2024-26585
+    - tls: fix race between tx work scheduling and socket close
+
+  * CVE-2024-26583
+    - tls: rx: jump to a more appropriate label
+    - tls: rx: drop pointless else after goto
+    - tls: stop recv() if initial process_rx_list gave us non-DATA
+    - tls: rx: don't store the record type in socket context
+    - tls: rx: don't store the decryption status in socket context
+    - tls: rx: don't issue wake ups when data is decrypted
+    - tls: rx: refactor decrypt_skb_update()
+    - tls: hw: rx: use return value of tls_device_decrypted() to carry status
+    - tls: rx: drop unnecessary arguments from tls_setup_from_iter()
+    - tls: rx: don't report text length from the bowels of decrypt
+    - tls: rx: wrap decryption arguments in a structure
+    - tls: rx: factor out writing ContentType to cmsg
+    - tls: rx: don't track the async count
+    - tls: rx: move counting TlsDecryptErrors for sync
+    - tls: rx: assume crypto always calls our callback
+    - tls: rx: use async as an in-out argument
+    - tls: decrement decrypt_pending if no async completion will be called
+    - net: tls: fix async vs NIC crypto offload
+    - Revert "tls: rx: move counting TlsDecryptErrors for sync"
+    - tls: rx: simplify async wait
+    - tls: rx: return the already-copied data on crypto error
+    - tls: rx: allow only one reader at a time
+    - tls: rx: release the sock lock on locking timeout
+    - tls: extract context alloc/initialization out of tls_set_sw_offload
+    - net: tls: factor out tls_*crypt_async_wait()
+    - tls: fix race between async notify and socket close
+
+  * CVE-2024-26622
+    - tomoyo: fix UAF write bug in tomoyo_write_control()
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Fri, 26 Apr 2024 13:29:50 +0200
+
+linux (5.15.0-106.116) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-106.116 -proposed tracker (LP: #2061812)
+
+  * CVE-2024-2201
+    - x86/bugs: Use sysfs_emit()
+    - KVM: x86: Update KVM-only leaf handling to allow for 100% KVM-only leafs
+    - KVM: x86: Advertise CPUID.(EAX=7,ECX=2):EDX[5:0] to userspace
+    - KVM: x86: Use a switch statement and macros in __feature_translate()
+    - x86/bugs: Change commas to semicolons in 'spectre_v2' sysfs file
+    - x86/syscall: Don't force use of indirect calls for system calls
+    - x86/bhi: Add support for clearing branch history at syscall entry
+    - x86/bhi: Define SPEC_CTRL_BHI_DIS_S
+    - x86/bhi: Enumerate Branch History Injection (BHI) bug
+    - x86/bhi: Add BHI mitigation knob
+    - x86/bhi: Mitigate KVM by default
+    - KVM: x86: Add BHI_NO
+    - [Config] Set CONFIG_BHI to enabled (auto)
+
+  * Drop fips-checks script from trees (LP: #2055083)
+    - [Packaging] Remove fips-checks script
+
+  * alsa/realtek: adjust max output valume for headphone on 2 LG machines
+    (LP: #2058573)
+    - ALSA: hda/realtek: fix the hp playback volume issue for LG machines
+
+  * A general-proteciton exception during guest migration to unsupported PKRU
+    machine (LP: #2032164)
+    - x86/fpu: Allow caller to constrain xfeatures when copying to uabi buffer
+    - KVM: x86: Constrain guest-supported xfeatures only at KVM_GET_XSAVE{2}
+
+  *  [ICX] [SPR] [ipc/msg] performance: Mitigate the lock contention with percpu
+    counter (LP: #2058485)
+    - ipc: check checkpoint_restore_ns_capable() to modify C/R proc files
+    - ipc/ipc_sysctl.c: remove fallback for !CONFIG_PROC_SYSCTL
+    - ipc: Store mqueue sysctls in the ipc namespace
+    - ipc: Store ipc sysctls in the ipc namespace
+    - ipc: Use the same namespace to modify and validate
+    - ipc: Remove extra1 field abuse to pass ipc namespace
+    - ipc: Check permissions for checkpoint_restart sysctls at open time
+    - percpu: add percpu_counter_add_local and percpu_counter_sub_local
+    - ipc/msg: mitigate the lock contention with percpu counter
+
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014)
+    - ksmbd: free ppace array on error in parse_dacl
+    - ksmbd: don't allow O_TRUNC open on read-only share
+    - ksmbd: validate mech token in session setup
+    - ksmbd: fix UAF issue in ksmbd_tcp_new_connection()
+    - ksmbd: only v2 leases handle the directory
+    - iio: adc: ad7091r: Set alert bit in config register
+    - iio: adc: ad7091r: Allow users to configure device events
+    - iio: adc: ad7091r: Enable internal vref if external vref is not supplied
+    - dmaengine: fix NULL pointer in channel unregistration function
+    - scsi: ufs: core: Simplify power management during async scan
+    - scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
+    - iio:adc:ad7091r: Move exports into IIO_AD7091R namespace.
+    - ext4: allow for the last group to be marked as trimmed
+    - btrfs: sysfs: validate scrub_speed_max value
+    - crypto: api - Disallow identical driver names
+    - PM: hibernate: Enforce ordering during image compression/decompression
+    - hwrng: core - Fix page fault dead lock on mmap-ed hwrng
+    - crypto: s390/aes - Fix buffer overread in CTR mode
+    - media: imx355: Enable runtime PM before registering async sub-device
+    - rpmsg: virtio: Free driver_override when rpmsg_remove()
+    - media: ov9734: Enable runtime PM before registering async sub-device
+    - mips: Fix max_mapnr being uninitialized on early stages
+    - bus: mhi: host: Drop chan lock before queuing buffers
+    - bus: mhi: host: Add spinlock to protect WP access when queueing TREs
+    - parisc/firmware: Fix F-extend for PDC addresses
+    - async: Split async_schedule_node_domain()
+    - async: Introduce async_schedule_dev_nocall()
+    - arm64: dts: qcom: sc7180: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sdm845: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sm8150: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sdm845: fix USB DP/DM HS PHY interrupts
+    - lsm: new security_file_ioctl_compat() hook
+    - scripts/get_abi: fix source path leak
+    - mmc: core: Use mrq.sbc in close-ended ffu
+    - mmc: mmc_spi: remove custom DMA mapped buffers
+    - rtc: Adjust failure return code for cmos_set_alarm()
+    - nouveau/vmm: don't set addr on the fail path to avoid warning
+    - ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path
+    - rename(): fix the locking of subdirectories
+    - ksmbd: set v2 lease version on lease upgrade
+    - ksmbd: fix potential circular locking issue in smb2_set_ea()
+    - ksmbd: don't increment epoch if current state and request state are same
+    - ksmbd: send lease break notification on FILE_RENAME_INFORMATION
+    - ksmbd: Add missing set_freezable() for freezable kthread
+    - net/smc: fix illegal rmb_desc access in SMC-D connection dump
+    - tcp: make sure init the accept_queue's spinlocks once
+    - bnxt_en: Wait for FLR to complete during probe
+    - vlan: skip nested type that is not IFLA_VLAN_QOS_MAPPING
+    - llc: make llc_ui_sendmsg() more robust against bonding changes
+    - llc: Drop support for ETH_P_TR_802_2.
+    - net/rds: Fix UBSAN: array-index-out-of-bounds in rds_cmsg_recv
+    - tracing: Ensure visibility when inserting an element into tracing_map
+    - afs: Hide silly-rename files from userspace
+    - tcp: Add memory barrier to tcp_push()
+    - netlink: fix potential sleeping issue in mqueue_flush_file
+    - ipv6: init the accept_queue's spinlocks in inet6_create
+    - net/mlx5: DR, Use the right GVMI number for drop action
+    - net/mlx5: DR, Align mlx5dv_dr API vport action with FW behavior
+    - net/mlx5: DR, Can't go to uplink vport on RX rule
+    - net/mlx5e: fix a double-free in arfs_create_groups
+    - net/mlx5e: fix a potential double-free in fs_any_create_groups
+    - overflow: Allow mixed type arguments
+    - netfilter: nft_limit: reject configurations that cause integer overflow
+    - netfilter: nf_tables: restrict anonymous set and map names to 16 bytes
+    - netfilter: nf_tables: validate NFPROTO_* family
+    - net: stmmac: Wait a bit for the reset to take effect
+    - net: mvpp2: clear BM pool before initialization
+    - selftests: netdevsim: fix the udp_tunnel_nic test
+    - fjes: fix memleaks in fjes_hw_setup
+    - net: fec: fix the unhandled context fault from smmu
+    - btrfs: fix infinite directory reads
+    - btrfs: set last dir index to the current last index when opening dir
+    - btrfs: refresh dir last index during a rewinddir(3) call
+    - btrfs: fix race between reading a directory and adding entries to it
+    - btrfs: avoid copying BTRFS_ROOT_SUBVOL_DEAD flag to snapshot of subvolume
+      being deleted
+    - btrfs: ref-verify: free ref cache before clearing mount opt
+    - btrfs: tree-checker: fix inline ref size in error messages
+    - btrfs: don't warn if discard range is not aligned to sector
+    - btrfs: defrag: reject unknown flags of btrfs_ioctl_defrag_range_args
+    - btrfs: don't abort filesystem when attempting to snapshot deleted subvolume
+    - rbd: don't move requests to the running list on errors
+    - exec: Fix error handling in begin_new_exec()
+    - wifi: iwlwifi: fix a memory corruption
+    - hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes
+    - netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress
+      basechain
+    - firmware: arm_scmi: Check mailbox/SMT channel for consistency
+    - xfs: read only mounts with fsopen mount API are busted
+    - gpiolib: acpi: Ignore touchpad wakeup on GPD G1619-04
+    - drm: Don't unref the same fb many times by mistake due to deadlock handling
+    - drm/bridge: nxp-ptn3460: fix i2c_master_send() error checking
+    - drm/tidss: Fix atomic_flush check
+    - drm/bridge: nxp-ptn3460: simplify some error checking
+    - PM: core: Remove unnecessary (void *) conversions
+    - PM: sleep: Fix possible deadlocks in core system-wide PM code
+    - bus: mhi: host: Rename "struct mhi_tre" to "struct mhi_ring_element"
+    - bus: mhi: host: Add alignment check for event ring read pointer
+    - fs/pipe: move check to pipe_has_watch_queue()
+    - pipe: wakeup wr_wait after setting max_usage
+    - ARM: dts: qcom: sdx55: fix USB wakeup interrupt types
+    - ARM: dts: samsung: exynos4210-i9100: Unconditionally enable LDO12
+    - ARM: dts: qcom: sdx55: fix pdc '#interrupt-cells'
+    - ARM: dts: qcom: sdx55: fix USB DP/DM HS PHY interrupts
+    - ARM: dts: qcom: sdx55: fix USB SS wakeup
+    - media: mtk-jpeg: Fix use after free bug due to error path handling in
+      mtk_jpeg_dec_device_run
+    - mm: use __pfn_to_section() instead of open coding it
+    - mm/sparsemem: fix race in accessing memory_section->usage
+    - PM / devfreq: Fix buffer overflow in trans_stat_show
+    - btrfs: add definition for EXTENT_TREE_V2
+    - ksmbd: fix global oob in ksmbd_nl_policy
+    - cpufreq: intel_pstate: Drop redundant intel_pstate_get_hwp_cap() call
+    - cpufreq: intel_pstate: Refine computation of P-state for given frequency
+    - drm: panel-simple: add missing bus flags for Tianma tm070jvhg[30/33]
+    - drm/exynos: fix accidental on-stack copy of exynos_drm_plane
+    - drm/exynos: gsc: minor fix for loop iteration in gsc_runtime_resume
+    - gpio: eic-sprd: Clear interrupt after set the interrupt type
+    - spi: bcm-qspi: fix SFDP BFPT read by usig mspi read
+    - mips: Call lose_fpu(0) before initializing fcr31 in mips_set_personality_nan
+    - tick/sched: Preserve number of idle sleeps across CPU hotplug events
+    - x86/entry/ia32: Ensure s32 is sign extended to s64
+    - powerpc/mm: Fix null-pointer dereference in pgtable_cache_add
+    - arm64: irq: set the correct node for VMAP stack
+    - drivers/perf: pmuv3: don't expose SW_INCR event in sysfs
+    - powerpc: Fix build error due to is_valid_bugaddr()
+    - powerpc/mm: Fix build failures due to arch_reserved_kernel_pages()
+    - powerpc/64s: Fix CONFIG_NUMA=n build due to create_section_mapping()
+    - x86/boot: Ignore NMIs during very early boot
+    - powerpc: pmd_move_must_withdraw() is only needed for
+      CONFIG_TRANSPARENT_HUGEPAGE
+    - powerpc/lib: Validate size for vector operations
+    - x86/mce: Mark fatal MCE's page as poison to avoid panic in the kdump kernel
+    - perf/core: Fix narrow startup race when creating the perf nr_addr_filters
+      sysfs file
+    - debugobjects: Stop accessing objects after releasing hash bucket lock
+    - regulator: core: Only increment use_count when enable_count changes
+    - audit: Send netlink ACK before setting connection in auditd_set
+    - ACPI: video: Add quirk for the Colorful X15 AT 23 Laptop
+    - PNP: ACPI: fix fortify warning
+    - ACPI: extlog: fix NULL pointer dereference check
+    - PM / devfreq: Synchronize devfreq_monitor_[start/stop]
+    - ACPI: APEI: set memory failure flags as MF_ACTION_REQUIRED on synchronous
+      events
+    - FS:JFS:UBSAN:array-index-out-of-bounds in dbAdjTree
+    - jfs: fix slab-out-of-bounds Read in dtSearch
+    - jfs: fix array-index-out-of-bounds in dbAdjTree
+    - pstore/ram: Fix crash when setting number of cpus to an odd number
+    - crypto: octeontx2 - Fix cptvf driver cleanup
+    - crypto: stm32/crc32 - fix parsing list of devices
+    - afs: fix the usage of read_seqbegin_or_lock() in afs_lookup_volume_rcu()
+    - afs: fix the usage of read_seqbegin_or_lock() in afs_find_server*()
+    - rxrpc_find_service_conn_rcu: fix the usage of read_seqbegin_or_lock()
+    - jfs: fix array-index-out-of-bounds in diNewExt
+    - arch: consolidate arch_irq_work_raise prototypes
+    - s390/ptrace: handle setting of fpc register correctly
+    - KVM: s390: fix setting of fpc register
+    - SUNRPC: Fix a suspicious RCU usage warning
+    - ecryptfs: Reject casefold directory inodes
+    - ext4: fix inconsistent between segment fstrim and full fstrim
+    - ext4: unify the type of flexbg_size to unsigned int
+    - ext4: remove unnecessary check from alloc_flex_gd()
+    - ext4: avoid online resizing failures due to oversized flex bg
+    - wifi: rt2x00: restart beacon queue when hardware reset
+    - selftests/bpf: satisfy compiler by having explicit return in btf test
+    - selftests/bpf: Fix pyperf180 compilation failure with clang18
+    - selftests/bpf: Fix issues in setup_classid_environment()
+    - scsi: lpfc: Fix possible file string name overflow when updating firmware
+    - PCI: Add no PM reset quirk for NVIDIA Spectrum devices
+    - bonding: return -ENOMEM instead of BUG in alb_upper_dev_walk
+    - scsi: arcmsr: Support new PCI device IDs 1883 and 1886
+    - ARM: dts: imx7d: Fix coresight funnel ports
+    - ARM: dts: imx7s: Fix lcdif compatible
+    - ARM: dts: imx7s: Fix nand-controller #size-cells
+    - wifi: ath9k: Fix potential array-index-out-of-bounds read in
+      ath9k_htc_txstatus()
+    - bpf: Add map and need_defer parameters to .map_fd_put_ptr()
+    - scsi: libfc: Don't schedule abort twice
+    - scsi: libfc: Fix up timeout error in fc_fcp_rec_error()
+    - bpf: Set uattr->batch.count as zero before batched update or deletion
+    - ARM: dts: rockchip: fix rk3036 hdmi ports node
+    - ARM: dts: imx25/27-eukrea: Fix RTC node name
+    - ARM: dts: imx: Use flash@0,0 pattern
+    - ARM: dts: imx27: Fix sram node
+    - ARM: dts: imx1: Fix sram node
+    - ionic: pass opcode to devcmd_wait
+    - block/rnbd-srv: Check for unlikely string overflow
+    - ARM: dts: imx25: Fix the iim compatible string
+    - ARM: dts: imx25/27: Pass timing0
+    - ARM: dts: imx27-apf27dev: Fix LED name
+    - ARM: dts: imx23-sansa: Use preferred i2c-gpios properties
+    - ARM: dts: imx23/28: Fix the DMA controller node name
+    - net: dsa: mv88e6xxx: Fix mv88e6352_serdes_get_stats error path
+    - block: prevent an integer overflow in bvec_try_merge_hw_page
+    - md: Whenassemble the array, consult the superblock of the freshest device
+    - arm64: dts: qcom: msm8996: Fix 'in-ports' is a required property
+    - arm64: dts: qcom: msm8998: Fix 'out-ports' is a required property
+    - wifi: rtl8xxxu: Add additional USB IDs for RTL8192EU devices
+    - libbpf: Fix NULL pointer dereference in bpf_object__collect_prog_relos
+    - ALSA: usb-audio: Add delay quirk for MOTU M Series 2nd revision
+    - wifi: rtlwifi: rtl8723{be,ae}: using calculate_bit_shift()
+    - wifi: cfg80211: free beacon_ies when overridden from hidden BSS
+    - Bluetooth: qca: Set both WIDEBAND_SPEECH and LE_STATES quirks for QCA2066
+    - Bluetooth: L2CAP: Fix possible multiple reject send
+    - bridge: cfm: fix enum typo in br_cc_ccm_tx_parse
+    - i40e: Fix VF disable behavior to block all traffic
+    - octeontx2-af: Fix max NPC MCAM entry check while validating ref_entry
+    - f2fs: fix to check return value of f2fs_reserve_new_block()
+    - ALSA: hda: Refer to correct stream index at loops
+    - ASoC: doc: Fix undefined SND_SOC_DAPM_NOPM argument
+    - fast_dput(): handle underflows gracefully
+    - RDMA/IPoIB: Fix error code return in ipoib_mcast_join
+    - drm/amd/display: Fix tiled display misalignment
+    - f2fs: fix write pointers on zoned device after roll forward
+    - drm/drm_file: fix use of uninitialized variable
+    - drm/framebuffer: Fix use of uninitialized variable
+    - drm/mipi-dsi: Fix detach call without attach
+    - media: stk1160: Fixed high volume of stk1160_dbg messages
+    - media: rockchip: rga: fix swizzling for RGB formats
+    - PCI: add INTEL_HDA_ARL to pci_ids.h
+    - ALSA: hda: Intel: add HDA_ARL PCI ID support
+    - ALSA: hda: intel-dspcfg: add filters for ARL-S and ARL
+    - media: rkisp1: Drop IRQF_SHARED
+    - f2fs: fix to tag gcing flag on page during block migration
+    - drm/exynos: Call drm_atomic_helper_shutdown() at shutdown/unbind time
+    - IB/ipoib: Fix mcast list locking
+    - media: ddbridge: fix an error code problem in ddb_probe
+    - media: i2c: imx335: Fix hblank min/max values
+    - drm/msm/dpu: Ratelimit framedone timeout msgs
+    - drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap
+    - clk: hi3620: Fix memory leak in hi3620_mmc_clk_init()
+    - clk: mmp: pxa168: Fix memory leak in pxa168_clk_init()
+    - watchdog: it87_wdt: Keep WDTCTRL bit 3 unmodified for IT8784/IT8786
+    - clk: imx: scu: Fix memory leak in __imx_clk_gpr_scu()
+    - clk: imx: clk-imx8qxp: fix LVDS bypass, pixel and phy clocks
+    - drm/amdgpu: Let KFD sync with VM fences
+    - drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
+    - ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140
+    - leds: trigger: panic: Don't register panic notifier if creating the trigger
+      failed
+    - um: Fix naming clash between UML and scheduler
+    - um: Don't use vfprintf() for os_info()
+    - um: net: Fix return type of uml_net_start_xmit()
+    - um: time-travel: fix time corruption
+    - i3c: master: cdns: Update maximum prescaler value for i2c clock
+    - xen/gntdev: Fix the abuse of underlying struct page in DMA-buf import
+    - mfd: ti_am335x_tscadc: Fix TI SoC dependencies
+    - [Config] updateconfigs for MFD_TI_AM335X_TSCADC
+    - mailbox: arm_mhuv2: Fix a bug for mhuv2_sender_interrupt
+    - PCI: Only override AMD USB controller if required
+    - PCI: switchtec: Fix stdev_release() crash after surprise hot remove
+    - perf cs-etm: Bump minimum OpenCSD version to ensure a bugfix is present
+    - usb: hub: Replace hardcoded quirk value with BIT() macro
+    - selftests/sgx: Fix linker script asserts
+    - tty: allow TIOCSLCKTRMIOS with CAP_CHECKPOINT_RESTORE
+    - fs/kernfs/dir: obey S_ISGID
+    - PCI: Fix 64GT/s effective data rate calculation
+    - PCI/AER: Decode Requester ID when no error info found
+    - libsubcmd: Fix memory leak in uniq()
+    - drm/amdkfd: Fix lock dependency warning
+    - virtio_net: Fix "‘%d’ directive writing between 1 and 11 bytes into a region
+      of size 10" warnings
+    - blk-mq: fix IO hang from sbitmap wakeup race
+    - ceph: fix deadlock or deadcode of misusing dget()
+    - drm/amd/powerplay: Fix kzalloc parameter 'ATOM_Tonga_PPM_Table' in
+      'get_platform_power_management_table()'
+    - drm/amdgpu: Release 'adev->pm.fw' before return in
+      'amdgpu_device_need_post()'
+    - drm/amdkfd: Fix 'node' NULL check in 'svm_range_get_range_boundaries()'
+    - perf: Fix the nr_addr_filters fix
+    - wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
+    - drm: using mul_u32_u32() requires linux/math64.h
+    - scsi: isci: Fix an error code problem in isci_io_request_build()
+    - scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler
+    - selftests: net: give more time for GRO aggregation
+    - ip6_tunnel: use dev_sw_netstats_rx_add()
+    - ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()
+    - tcp: add sanity checks to rx zerocopy
+    - ixgbe: Remove non-inclusive language
+    - ixgbe: Refactor returning internal error codes
+    - ixgbe: Refactor overtemp event handling
+    - ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550()
+    - ipv6: Ensure natural alignment of const ipv6 loopback and router addresses
+    - llc: call sock_orphan() at release time
+    - bridge: mcast: fix disabled snooping after long uptime
+    - netfilter: nf_tables: restrict tunnel object to NFPROTO_NETDEV
+    - netfilter: nf_log: replace BUG_ON by WARN_ON_ONCE when putting logger
+    - netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom
+      expectations
+    - net: ipv4: fix a memleak in ip_setup_cork
+    - af_unix: fix lockdep positive in sk_diag_dump_icons()
+    - SAUCE: Sync apparmor copy of af_unix.c
+    - selftests: net: fix available tunnels detection
+    - net: sysfs: Fix /sys/class/net/<iface> path
+    - arm64: irq: set the correct node for shadow call stack
+    - gve: Fix use-after-free vulnerability
+    - HID: apple: Add support for the 2021 Magic Keyboard
+    - HID: apple: Add 2021 magic keyboard FN key mapping
+    - bonding: remove print in bond_verify_device_path
+    - ASoC: codecs: lpass-wsa-macro: fix compander volume hack
+    - dmaengine: fsl-dpaa2-qdma: Fix the size of dma pools
+    - dmaengine: ti: k3-udma: Report short packet errors
+    - dmaengine: fsl-qdma: Fix a memory leak related to the status queue DMA
+    - dmaengine: fsl-qdma: Fix a memory leak related to the queue command DMA
+    - phy: renesas: rcar-gen3-usb2: Fix returning wrong error code
+    - dmaengine: fix is_slave_direction() return false when DMA_DEV_TO_DEV
+    - phy: ti: phy-omap-usb2: Fix NULL pointer dereference for SRP
+    - drm/msm/dp: return correct Colorimetry for DP_TEST_DYNAMIC_RANGE_CEA case
+    - net: stmmac: xgmac: fix handling of DPP safety error for DMA channels
+    - selftests: net: cut more slack for gro fwd tests.
+    - selftests: net: avoid just another constant wait
+    - tunnels: fix out of bounds access when building IPv6 PMTU error
+    - atm: idt77252: fix a memleak in open_card_ubr0
+    - octeontx2-pf: Fix a memleak otx2_sq_init
+    - hwmon: (aspeed-pwm-tacho) mutex for tach reading
+    - hwmon: (coretemp) Fix out-of-bounds memory access
+    - hwmon: (coretemp) Fix bogus core_id to attr name mapping
+    - inet: read sk->sk_family once in inet_recv_error()
+    - rxrpc: Fix response to PING RESPONSE ACKs to a dead call
+    - tipc: Check the bearer type before calling tipc_udp_nl_bearer_add()
+    - af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.
+    - ppp_async: limit MRU to 64K
+    - netfilter: nft_compat: reject unused compat flag
+    - netfilter: nft_compat: restrict match/target protocol to u16
+    - drm/amd/display: Fix multiple memory leaks reported by coverity
+    - drm/amd/display: Implement bounds check for stream encoder creation in
+      DCN301
+    - netfilter: nft_ct: reject direction for ct id
+    - netfilter: nft_set_pipapo: store index in scratch maps
+    - netfilter: nft_set_pipapo: add helper to release pcpu scratch area
+    - netfilter: nft_set_pipapo: remove scratch_aligned pointer
+    - fs/ntfs3: Fix an NULL dereference bug
+    - scsi: core: Move scsi_host_busy() out of host lock if it is for per-command
+    - blk-iocost: Fix an UBSAN shift-out-of-bounds warning
+    - drivers: lkdtm: fix clang -Wformat warning
+    - ALSA: usb-audio: Add a quirk for Yamaha YIT-W12TX transmitter
+    - USB: serial: qcserial: add new usb-id for Dell Wireless DW5826e
+    - USB: serial: option: add Fibocom FM101-GL variant
+    - USB: serial: cp210x: add ID for IMST iM871A-USB
+    - usb: dwc3: host: Set XHCI_SG_TRB_CACHE_SIZE_QUIRK
+    - usb: host: xhci-plat: Add support for XHCI_SG_TRB_CACHE_SIZE_QUIRK
+    - hrtimer: Report offline hrtimer enqueue
+    - Input: i8042 - fix strange behavior of touchpad on Clevo NS70PU
+    - Input: atkbd - skip ATKBD_CMD_SETLEDS when skipping ATKBD_CMD_GETID
+    - clocksource: Skip watchdog check for large watchdog intervals
+    - net: stmmac: xgmac: use #define for string constants
+    - net: stmmac: xgmac: fix a typo of register name in DPP safety handling
+    - btrfs: forbid creating subvol qgroups
+    - btrfs: forbid deleting live subvol qgroup
+    - btrfs: send: return EOPNOTSUPP on unknown flags
+    - of: unittest: Fix compile in the non-dynamic case
+    - wifi: iwlwifi: Fix some error codes
+    - net: openvswitch: limit the number of recursions from action sets
+    - spi: ppc4xx: Drop write-only variable
+    - ASoC: rt5645: Fix deadlock in rt5645_jack_detect_work()
+    - net: sysfs: Fix /sys/class/net/<iface> path for statistics
+    - MIPS: Add 'memory' clobber to csum_ipv6_magic() inline assembler
+    - i40e: Fix waiting for queues of all VSIs to be disabled
+    - scs: add CONFIG_MMU dependency for vfree_atomic()
+    - tracing/trigger: Fix to return error if failed to alloc snapshot
+    - mm/writeback: fix possible divide-by-zero in wb_dirty_limits(), again
+    - scsi: storvsc: Fix ring buffer size calculation
+    - ALSA: hda/realtek: Fix the external mic not being recognised for Acer Swift
+      1 SF114-32
+    - ALSA: hda/realtek: Enable Mute LED on HP Laptop 14-fq0xxx
+    - HID: i2c-hid-of: fix NULL-deref on failed power up
+    - HID: wacom: generic: Avoid reporting a serial of '0' to userspace
+    - HID: wacom: Do not register input devices until after hid_hw_start
+    - iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP
+    - usb: ucsi_acpi: Fix command completion handling
+    - USB: hub: check for alternate port before enabling A_ALT_HNP_SUPPORT
+    - usb: f_mass_storage: forbid async queue when shutdown happen
+    - usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend
+    - media: ir_toy: fix a memleak in irtoy_tx
+    - powerpc/kasan: Fix addr error caused by page alignment
+    - i2c: i801: Remove i801_set_block_buffer_mode
+    - i2c: i801: Fix block process call transactions
+    - modpost: trim leading spaces when processing source files list
+    - mptcp: fix data re-injection from stale subflow
+    - scsi: Revert "scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock"
+    - Revert "drm/amd: flush any delayed gfxoff on suspend entry"
+    - firewire: core: correct documentation of fw_csr_string() kernel API
+    - kbuild: Fix changing ELF file type for output of gen_btf for big endian
+    - nfc: nci: free rx_data_reassembly skb on NCI device cleanup
+    - net: hsr: remove WARN_ONCE() in send_hsr_supervision_frame()
+    - xen-netback: properly sync TX responses
+    - ALSA: hda/realtek: Enable headset mic on Vaio VJFE-ADL
+    - ASoC: codecs: wcd938x: handle deferred probe
+    - binder: signal epoll threads of self-work
+    - misc: fastrpc: Mark all sessions as invalid in cb_remove
+    - ext4: fix double-free of blocks due to wrong extents moved_len
+    - tracing: Fix wasted memory in saved_cmdlines logic
+    - staging: iio: ad5933: fix type mismatch regression
+    - iio: magnetometer: rm3100: add boundary check for the value read from
+      RM3100_REG_TMRC
+    - iio: core: fix memleak in iio_device_register_sysfs
+    - iio: accel: bma400: Fix a compilation problem
+    - media: rc: bpf attach/detach requires write permission
+    - drm/prime: Support page array >= 4GB
+    - hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove
+    - ring-buffer: Clean ring_buffer_poll_wait() error return
+    - serial: max310x: set default value when reading clock ready bit
+    - serial: max310x: improve crystal stable clock detection
+    - serial: max310x: fail probe if clock crystal is unstable
+    - powerpc/64: Set task pt_regs->link to the LR value on scv entry
+    - x86/Kconfig: Transmeta Crusoe is CPU family 5, not 6
+    - x86/mm/ident_map: Use gbpages only where full GB page should be mapped.
+    - mmc: slot-gpio: Allow non-sleeping GPIO ro
+    - ALSA: hda/conexant: Add quirk for SWS JS201D
+    - nilfs2: fix data corruption in dsync block recovery for small block sizes
+    - nilfs2: fix hang in nilfs_lookup_dirty_data_buffers()
+    - crypto: ccp - Fix null pointer dereference in __sev_platform_shutdown_locked
+    - nfp: use correct macro for LengthSelect in BAR config
+    - nfp: flower: prevent re-adding mac index for bonded port
+    - wifi: mac80211: reload info pointer in ieee80211_tx_dequeue()
+    - irqchip/irq-brcmstb-l2: Add write memory barrier before exit
+    - irqchip/gic-v3-its: Fix GICv4.1 VPE affinity update
+    - net: ethernet: ti: cpsw: enable mac_managed_pm to fix mdio
+    - s390/qeth: Fix potential loss of L3-IP@ in case of network issues
+    - net: ethernet: ti: cpsw_new: enable mac_managed_pm to fix mdio
+    - ceph: prevent use-after-free in encode_cap_msg()
+    - mm: hugetlb pages should not be reserved by shmat() if SHM_NORESERVE
+    - of: property: fix typo in io-channels
+    - can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
+    - can: j1939: Fix UAF in j1939_sk_match_filter during
+      setsockopt(SO_J1939_FILTER)
+    - pmdomain: core: Move the unused cleanup to a _sync initcall
+    - tracing: Inform kmemleak of saved_cmdlines allocation
+    - af_unix: Fix task hung while purging oob_skb in GC.
+    - dma-buf: add dma_fence_timestamp helper
+    - bus: moxtet: Add spi device table
+    - crypto: lib/mpi - Fix unexpected pointer access in mpi_ec_init
+    - usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
+    - usb: dwc3: ep0: Don't prepare beyond Setup stage
+    - usb: dwc3: gadget: Only End Transfer for ep0 data phase
+    - usb: dwc3: gadget: Delay issuing End Transfer
+    - usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
+    - usb: dwc3: gadget: Force sending delayed status during soft disconnect
+    - usb: dwc3: gadget: Submit endxfer command if delayed during disconnect
+    - usb: dwc3: gadget: Stall and restart EP0 if host is unresponsive
+    - usb: dwc3: gadget: Refactor EP0 forced stall/restart into a separate API
+    - usb: dwc3: gadget: Handle EP0 request dequeuing properly
+    - usb: dwc3: gadget: Queue PM runtime idle on disconnect event
+    - serial: 8250_exar: Fill in rs485_supported
+    - serial: 8250_exar: Set missing rs485_supported flag
+    - fbdev/defio: Early-out if page is already enlisted
+    - fbdev: Don't sort deferred-I/O pages by default
+    - fbdev: defio: fix the pagelist corruption
+    - fbdev: Track deferred-I/O pages in pageref struct
+    - fbdev: Rename pagelist to pagereflist for deferred I/O
+    - fbdev: Fix invalid page access after closing deferred I/O devices
+    - fbdev: Fix incorrect page mapping clearance at fb_deferred_io_release()
+    - fbdev: flush deferred IO before closing
+    - scripts/decode_stacktrace.sh: support old bash version
+    - scripts: decode_stacktrace: demangle Rust symbols
+    - scripts/decode_stacktrace.sh: optionally use LLVM utilities
+    - netfilter: ipset: fix performance regression in swap operation
+    - hrtimer: Ignore slack time for RT tasks in schedule_hrtimeout_range()
+    - net: prevent mss overflow in skb_segment()
+    - netfilter: ipset: Missing gc cancellations fixed
+    - sched/membarrier: reduce the ability to hammer on sys_membarrier
+    - nilfs2: fix potential bug in end_buffer_async_write
+    - nilfs2: replace WARN_ONs for invalid DAT metadata block requests
+    - arm64: Subscribe Microsoft Azure Cobalt 100 to ARM Neoverse N2 errata
+    - PM: runtime: Have devm_pm_runtime_enable() handle
+      pm_runtime_dont_use_autosuspend()
+    - drm/msm/dsi: Enable runtime PM
+    - net: bcmgenet: Fix EEE implementation
+    - fs/ntfs3: Add null pointer checks
+    - staging: fbtft: core: set smem_len before fb_deferred_io_init call
+    - usb: dwc3: gadget: Don't delay End Transfer on delayed_status
+    - usb: dwc3: gadget: Execute gadget stop after halting the controller
+    - media: Revert "media: rkisp1: Drop IRQF_SHARED"
+    - usb: dwc3: gadget: Ignore End Transfer delay on teardown
+    - Linux 5.15.149
+
+  * Fix headphone mic detection issue on ALC897 (LP: #2056418)
+    - ALSA: hda/realtek - Fix headset Mic no show at resume back for Lenovo ALC897
+      platform
+
+  * CVE-2023-6039
+    - timers: Replace BUG_ON()s
+
+  * Problems with HVCS and hotplugging (LP: #2056373)
+    - hvcs: Fix hvcs port reference counting
+    - hvcs: Use dev_groups to manage hvcs device attributes
+    - hvcs: Use driver groups to manage driver attributes
+    - hvcs: Get reference to tty in remove
+    - hvcs: Use vhangup in hotplug remove
+    - hvcs: Synchronize hotplug remove with port free
+
+  * KVM: arm64: softlockups in stage2_apply_range (LP: #2056227)
+    - KVM: arm64: Work out supported block level at compile time
+    - KVM: arm64: Limit stage2_apply_range() batch size to largest block
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 16 Apr 2024 16:11:14 +0200
+
+linux (5.15.0-105.115) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-105.115 -proposed tracker (LP: #2061372)
+
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014) // CIFS
+    stopped working/is unstable with kernel update to 5.15.0-102.112
+    (LP: #2060780)
+    - smb3: Replace smb2pdu 1-element arrays with flex-arrays
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Mon, 15 Apr 2024 10:38:15 +0200
+
+linux (5.15.0-103.113) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-103.113 -proposed tracker (LP: #2059683)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop getabis data
+
+  * Remove getabis scripts (LP: #2059143)
+    - [Packaging] Remove getabis
+
+  * CVE-2023-24023
+    - Bluetooth: Add more enc key size check
+
+  * CVE-2023-52600
+    - jfs: fix uaf in jfs_evict_inode
+
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014) //
+    CVE-2023-52603
+    - UBSAN: array-index-out-of-bounds in dtSplitRoot
+
+  * CVE-2024-26581
+    - netfilter: nft_set_rbtree: skip end interval element from gc
+
+ -- Manuel Diewald <manuel.diewald@canonical.com>  Thu, 28 Mar 2024 19:21:10 +0100
+
+linux (5.15.0-102.112) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-102.112 -proposed tracker (LP: #2055632)
+
+  * Drop ABI checks from kernel build (LP: #2055686)
+    - [Packaging] Remove in-tree abi checks
+    - [Packaging] Drop abi checks from final-checks
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop ABI data
+    - [Packaging] update annotations scripts
+    - debian.master/dkms-versions -- update from kernel-versions (main/2024.03.04)
+
+  * block/loop: No longer allows to create partitions (LP: #2056143)
+    - block, loop: support partitions without scanning
+
+  * Cranky update-dkms-versions rollout (LP: #2055685)
+    - [Packaging] remove update-dkms-versions
+    - Move debian/dkms-versions to debian.master/dkms-versions
+    - [Packaging] Replace debian/dkms-versions with $(DEBIAN)/dkms-versions
+    - [Packaging] remove update-version-dkms
+
+  * linux: please move erofs.ko (CONFIG_EROFS for EROFS support) from linux-
+    modules-extra to linux-modules (LP: #2054809)
+    - UBUNTU [Packaging]: Include erofs in linux-modules instead of linux-modules-
+      extra
+
+  * linux-tools-common: man page of usbip[d] is misplaced (LP: #2054094)
+    - [Packaging] rules: Put usbip manpages in the correct directory
+
+  * CVE-2024-23851
+    - dm ioctl: log an error if the ioctl structure is corrupted
+    - dm: limit the number of targets and parameter size area
+
+  * CVE-2024-23850
+    - btrfs: do not ASSERT() if the newly created subvolume already got read
+
+  * x86: performance: tsc: Extend watchdog check exemption to 4-Sockets platform
+    (LP: #2054699)
+    - x86/tsc: Extend watchdog check exemption to 4-Sockets platform
+
+  * linux: please move dmi-sysfs.ko (CONFIG_DMI_SYSFS for SMBIOS support) from
+    linux-modules-extra to linux-modules (LP: #2045561)
+    - [Packaging] Move dmi-sysfs.ko into linux-modules
+
+  * Fix bpf selftests build failure after v5.15.139 update (LP: #2054567)
+    - Revert "selftests/bpf: Test tail call counting with bpf2bpf and data on
+      stack"
+
+  * Jammy update: v5.15.148 upstream stable release (LP: #2055145)
+    - f2fs: explicitly null-terminate the xattr list
+    - pinctrl: lochnagar: Don't build on MIPS
+    - ALSA: hda - Fix speaker and headset mic pin config for CHUWI CoreBook XPro
+    - mptcp: fix uninit-value in mptcp_incoming_options
+    - wifi: cfg80211: lock wiphy mutex for rfkill poll
+    - debugfs: fix automount d_fsdata usage
+    - drm/amdgpu: Fix cat debugfs amdgpu_regs_didt causes kernel null pointer
+    - nvme-core: check for too small lba shift
+    - ASoC: wm8974: Correct boost mixer inputs
+    - ASoC: Intel: Skylake: Fix mem leak in few functions
+    - ASoC: nau8822: Fix incorrect type in assignment and cast to restricted
+      __be16
+    - ASoC: Intel: Skylake: mem leak in skl register function
+    - ASoC: cs43130: Fix the position of const qualifier
+    - ASoC: cs43130: Fix incorrect frame delay configuration
+    - ASoC: rt5650: add mutex to avoid the jack detection failure
+    - nouveau/tu102: flush all pdbs on vmm flush
+    - net/tg3: fix race condition in tg3_reset_task()
+    - ASoC: da7219: Support low DC impedance headset
+    - ASoC: ops: add correct range check for limiting volume
+    - nvme: introduce helper function to get ctrl state
+    - drm/amdgpu: Add NULL checks for function pointers
+    - drm/exynos: fix a potential error pointer dereference
+    - drm/exynos: fix a wrong error checking
+    - hwmon: (corsair-psu) Fix probe when built-in
+    - clk: rockchip: rk3128: Fix HCLK_OTG gate register
+    - jbd2: correct the printing of write_flags in jbd2_write_superblock()
+    - drm/crtc: Fix uninit-value bug in drm_mode_setcrtc
+    - neighbour: Don't let neigh_forced_gc() disable preemption for long
+    - platform/x86: intel-vbtn: Fix missing tablet-mode-switch events
+    - jbd2: fix soft lockup in journal_finish_inode_data_buffers()
+    - tracing: Have large events show up as '[LINE TOO BIG]' instead of nothing
+    - tracing: Add size check when printing trace_marker output
+    - stmmac: dwmac-loongson: drop useless check for compatible fallback
+    - MIPS: dts: loongson: drop incorrect dwmac fallback compatible
+    - tracing: Fix uaf issue when open the hist or hist_debug file
+    - ring-buffer: Do not record in NMI if the arch does not support cmpxchg in
+      NMI
+    - reset: hisilicon: hi6220: fix Wvoid-pointer-to-enum-cast warning
+    - Input: atkbd - skip ATKBD_CMD_GETID in translated mode
+    - Input: i8042 - add nomux quirk for Acer P459-G2-M
+    - s390/scm: fix virtual vs physical address confusion
+    - ARC: fix spare error
+    - wifi: iwlwifi: pcie: avoid a NULL pointer dereference
+    - Input: xpad - add Razer Wolverine V2 support
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Medion Lifetab S10346
+    - i2c: rk3x: fix potential spinlock recursion on poll
+    - net: qrtr: ns: Return 0 if server port is not present
+    - ARM: sun9i: smp: fix return code check of of_property_match_string
+    - drm/crtc: fix uninitialized variable use
+    - ACPI: resource: Add another DMI match for the TongFang GMxXGxx
+    - Revert "ASoC: atmel: Remove system clock tree configuration for
+      at91sam9g20ek"
+    - bpf: Add --skip_encoding_btf_inconsistent_proto, --btf_gen_optimized to
+      pahole flags for v1.25
+    - kprobes: Fix to handle forcibly unoptimized kprobes on freeing_list
+    - Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"
+    - binder: use EPOLLERR from eventpoll.h
+    - binder: fix use-after-free in shinker's callback
+    - binder: fix trivial typo of binder_free_buf_locked()
+    - binder: fix comment on binder_alloc_new_buf() return value
+    - uio: Fix use-after-free in uio_open
+    - parport: parport_serial: Add Brainboxes BAR details
+    - parport: parport_serial: Add Brainboxes device IDs and geometry
+    - leds: ledtrig-tty: Free allocated ttyname buffer on deactivate
+    - PCI: Add ACS quirk for more Zhaoxin Root Ports
+    - coresight: etm4x: Fix width of CCITMIN field
+    - x86/lib: Fix overflow when counting digits
+    - EDAC/thunderx: Fix possible out-of-bounds string access
+    - powerpc: Mark .opd section read-only
+    - powerpc/toc: Future proof kernel toc
+    - powerpc: remove checks for binutils older than 2.25
+    - powerpc: add crtsavres.o to always-y instead of extra-y
+    - powerpc/44x: select I2C for CURRITUCK
+    - powerpc/pseries/memhp: Fix access beyond end of drmem array
+    - selftests/powerpc: Fix error handling in FPU/VMX preemption tests
+    - powerpc/powernv: Add a null pointer check to scom_debug_init_one()
+    - powerpc/powernv: Add a null pointer check in opal_event_init()
+    - powerpc/powernv: Add a null pointer check in opal_powercap_init()
+    - powerpc/imc-pmu: Add a null pointer check in update_events_in_group()
+    - spi: spi-zynqmp-gqspi: fix driver kconfig dependencies
+    - mtd: rawnand: Increment IFC_TIMEOUT_MSECS for nand controller response
+    - ACPI: video: check for error while searching for backlight device parent
+    - ACPI: LPIT: Avoid u32 multiplication overflow
+    - of: property: define of_property_read_u{8,16,32,64}_array() unconditionally
+    - of: Add of_property_present() helper
+    - cpufreq: Use of_property_present() for testing DT property presence
+    - cpufreq: scmi: process the result of devm_of_clk_add_hw_provider()
+    - calipso: fix memory leak in netlbl_calipso_add_pass()
+    - efivarfs: force RO when remounting if SetVariable is not supported
+    - spi: sh-msiof: Enforce fixed DTDL for R-Car H3
+    - ACPI: LPSS: Fix the fractional clock divider flags
+    - ACPI: extlog: Clear Extended Error Log status when RAS_CEC handled the error
+    - kunit: debugfs: Fix unchecked dereference in debugfs_print_results()
+    - mtd: Fix gluebi NULL pointer dereference caused by ftl notifier
+    - selinux: Fix error priority for bind with AF_UNSPEC on PF_INET6 socket
+    - crypto: virtio - Handle dataq logic with tasklet
+    - crypto: sa2ul - Return crypto_aead_setkey to transfer the error
+    - crypto: ccp - fix memleak in ccp_init_dm_workarea
+    - crypto: af_alg - Disallow multiple in-flight AIO requests
+    - crypto: sahara - remove FLAGS_NEW_KEY logic
+    - crypto: sahara - fix cbc selftest failure
+    - crypto: sahara - fix ahash selftest failure
+    - crypto: sahara - fix processing requests with cryptlen < sg->length
+    - crypto: sahara - fix error handling in sahara_hw_descriptor_create()
+    - pstore: ram_core: fix possible overflow in persistent_ram_init_ecc()
+    - fs: indicate request originates from old mount API
+    - gfs2: Fix kernel NULL pointer dereference in gfs2_rgrp_dump
+    - crypto: virtio - Wait for tasklet to complete on device remove
+    - crypto: sahara - avoid skcipher fallback code duplication
+    - crypto: sahara - handle zero-length aes requests
+    - crypto: sahara - fix ahash reqsize
+    - crypto: sahara - fix wait_for_completion_timeout() error handling
+    - crypto: sahara - improve error handling in sahara_sha_process()
+    - crypto: sahara - fix processing hash requests with req->nbytes < sg->length
+    - crypto: sahara - do not resize req->src when doing hash operations
+    - crypto: scomp - fix req->dst buffer overflow
+    - blocklayoutdriver: Fix reference leak of pnfs_device_node
+    - NFSv4.1/pnfs: Ensure we handle the error NFS4ERR_RETURNCONFLICT
+    - wifi: rtw88: fix RX filter in FIF_ALLMULTI flag
+    - bpf, lpm: Fix check prefixlen before walking trie
+    - bpf: Add crosstask check to __bpf_get_stack
+    - wifi: ath11k: Defer on rproc_get failure
+    - wifi: libertas: stop selecting wext
+    - ARM: dts: qcom: apq8064: correct XOADC register address
+    - net/ncsi: Fix netlink major/minor version numbers
+    - firmware: ti_sci: Fix an off-by-one in ti_sci_debugfs_create()
+    - firmware: meson_sm: populate platform devices from sm device tree data
+    - wifi: rtlwifi: rtl8821ae: phy: fix an undefined bitwise shift behavior
+    - arm64: dts: ti: k3-am65-main: Fix DSS irq trigger type
+    - bpf: enforce precision of R0 on callback return
+    - ARM: dts: qcom: sdx65: correct SPMI node name
+    - arm64: dts: qcom: sc7180: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sc7280: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sdm845: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sm8150: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sm8250: Make watchdog bark interrupt edge triggered
+    - bpf: fix check for attempt to corrupt spilled pointer
+    - scsi: fnic: Return error if vmalloc() failed
+    - arm64: dts: qcom: qrb5165-rb5: correct LED panic indicator
+    - arm64: dts: qcom: sdm845-db845c: correct LED panic indicator
+    - arm64: dts: qcom: sc7280: fix usb_2 wakeup interrupt types
+    - bpf: Fix verification of indirect var-off stack access
+    - block: Set memalloc_noio to false on device_add_disk() error path
+    - scsi: hisi_sas: Rename HISI_SAS_{RESET -> RESETTING}_BIT
+    - scsi: hisi_sas: Prevent parallel FLR and controller reset
+    - scsi: hisi_sas: Replace with standard error code return value
+    - scsi: hisi_sas: Rollback some operations if FLR failed
+    - scsi: hisi_sas: Correct the number of global debugfs registers
+    - selftests/net: fix grep checking for fib_nexthop_multiprefix
+    - virtio/vsock: fix logic which reduces credit update messages
+    - dma-mapping: Add dma_release_coherent_memory to DMA API
+    - dma-mapping: clear dev->dma_mem to NULL after freeing it
+    - soc: qcom: llcc: Fix dis_cap_alloc and retain_on_pc configuration
+    - arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
+    - block: add check of 'minors' and 'first_minor' in device_add_disk()
+    - arm64: dts: qcom: sc7280: Mark SDHCI hosts as cache-coherent
+    - wifi: rtlwifi: add calculate_bit_shift()
+    - wifi: rtlwifi: rtl8188ee: phy: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192c: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192cu: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192ce: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192de: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192ee: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192se: using calculate_bit_shift()
+    - wifi: iwlwifi: mvm: set siso/mimo chains to 1 in FW SMPS request
+    - wifi: iwlwifi: mvm: send TX path flush in rfkill
+    - netfilter: nf_tables: mark newset as dead on transaction abort
+    - Bluetooth: Fix bogus check for re-auth no supported with non-ssp
+    - Bluetooth: btmtkuart: fix recv_buf() return value
+    - block: make BLK_DEF_MAX_SECTORS unsigned
+    - null_blk: don't cap max_hw_sectors to BLK_DEF_MAX_SECTORS
+    - net/sched: act_ct: fix skb leak and crash on ooo frags
+    - mlxbf_gige: Fix intermittent no ip issue
+    - net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
+    - mlxbf_gige: Enable the GigE port in mlxbf_gige_open
+    - ip6_tunnel: fix NEXTHDR_FRAGMENT handling in ip6_tnl_parse_tlv_enc_lim()
+    - ARM: davinci: always select CONFIG_CPU_ARM926T
+    - Revert "drm/tidss: Annotate dma-fence critical section in commit path"
+    - Revert "drm/omapdrm: Annotate dma-fence critical section in commit path"
+    - RDMA/usnic: Silence uninitialized symbol smatch warnings
+    - RDMA/hns: Fix inappropriate err code for unsupported operations
+    - drm/panel-elida-kd35t133: hold panel in reset for unprepare
+    - drm/nouveau/fence:: fix warning directly dereferencing a rcu pointer
+    - drm/bridge: tpd12s015: Drop buggy __exit annotation for remove function
+    - drm/tilcdc: Fix irq free on unload
+    - media: pvrusb2: fix use after free on context disconnection
+    - drm/bridge: Fix typo in post_disable() description
+    - f2fs: fix to avoid dirent corruption
+    - drm/radeon/r600_cs: Fix possible int overflows in r600_cs_check_reg()
+    - drm/radeon/r100: Fix integer overflow issues in r100_cs_track_check()
+    - drm/radeon: check return value of radeon_ring_lock()
+    - ASoC: cs35l33: Fix GPIO name and drop legacy include
+    - ASoC: cs35l34: Fix GPIO name and drop legacy include
+    - drm/msm/mdp4: flush vblank event on disable
+    - drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks
+    - drm/drv: propagate errors from drm_modeset_register_all()
+    - drm/radeon: check the alloc_workqueue return value in radeon_crtc_init()
+    - drm/radeon/dpm: fix a memleak in sumo_parse_power_table
+    - drm/radeon/trinity_dpm: fix a memleak in trinity_parse_power_table
+    - drm/bridge: cdns-mhdp8546: Fix use of uninitialized variable
+    - drm/bridge: tc358767: Fix return value on error case
+    - media: cx231xx: fix a memleak in cx231xx_init_isoc
+    - clk: qcom: gpucc-sm8150: Update the gpu_cc_pll1 config
+    - media: rkisp1: Disable runtime PM in probe error path
+    - f2fs: fix to check compress file in f2fs_move_file_range()
+    - f2fs: fix to update iostat correctly in f2fs_filemap_fault()
+    - f2fs: fix the f2fs_file_write_iter tracepoint
+    - media: dvbdev: drop refcount on error path in dvb_device_open()
+    - media: dvb-frontends: m88ds3103: Fix a memory leak in an error handling path
+      of m88ds3103_probe()
+    - drm/amdgpu/debugfs: fix error code when smc register accessors are NULL
+    - drm/amd/pm: fix a double-free in si_dpm_init
+    - drivers/amd/pm: fix a use-after-free in kv_parse_power_table
+    - gpu/drm/radeon: fix two memleaks in radeon_vm_init
+    - dt-bindings: clock: Update the videocc resets for sm8150
+    - clk: qcom: videocc-sm8150: Update the videocc resets
+    - clk: qcom: videocc-sm8150: Add missing PLL config property
+    - drivers: clk: zynqmp: calculate closest mux rate
+    - clk: zynqmp: make bestdiv unsigned
+    - clk: zynqmp: Add a check for NULL pointer
+    - drivers: clk: zynqmp: update divider round rate logic
+    - watchdog: set cdev owner before adding
+    - watchdog/hpwdt: Only claim UNKNOWN NMI if from iLO
+    - watchdog: bcm2835_wdt: Fix WDIOC_SETTIMEOUT handling
+    - watchdog: rti_wdt: Drop runtime pm reference count when watchdog is unused
+    - clk: si5341: fix an error code problem in si5341_output_clk_set_rate
+    - clk: asm9260: use parent index to link the reference clock
+    - clk: fixed-rate: add devm_clk_hw_register_fixed_rate
+    - clk: fixed-rate: fix clk_hw_register_fixed_rate_with_accuracy_parent_hw
+    - pwm: stm32: Use regmap_clear_bits and regmap_set_bits where applicable
+    - pwm: stm32: Use hweight32 in stm32_pwm_detect_channels
+    - pwm: stm32: Fix enable count for clk in .probe()
+    - ASoC: rt5645: Drop double EF20 entry from dmi_platform_data[]
+    - ALSA: scarlett2: Add missing error check to scarlett2_config_save()
+    - ALSA: scarlett2: Add missing error check to scarlett2_usb_set_config()
+    - ALSA: scarlett2: Allow passing any output to line_out_remap()
+    - ALSA: scarlett2: Add missing error checks to *_ctl_get()
+    - ALSA: scarlett2: Add clamp() in scarlett2_mixer_ctl_put()
+    - mmc: sdhci_am654: Fix TI SoC dependencies
+    - [Config] update annotations for CONFIG_MMC_SDHCI_AM654
+    - [Config] remove sdhci_am654 module for armhf/ppc64el
+    - mmc: sdhci_omap: Fix TI SoC dependencies
+    - [Config] update annotations for CONFIG_MMC_SDHCI_OMAP
+    - [Config] remove sdhci-omap module for arm64/ppc64el
+    - IB/iser: Prevent invalidating wrong MR
+    - drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
+    - ksmbd: validate the zero field of packet header
+    - of: Fix double free in of_parse_phandle_with_args_map
+    - of: unittest: Fix of_count_phandle_with_args() expected value message
+    - selftests/bpf: Add assert for user stacks in test_task_stack
+    - binder: fix async space check for 0-sized buffers
+    - binder: fix unused alloc->free_async_space
+    - Input: atkbd - use ab83 as id when skipping the getid command
+    - dma-mapping: Fix build error unused-value
+    - virtio-crypto: fix memory leak in virtio_crypto_alg_skcipher_close_session()
+    - binder: fix race between mmput() and do_exit()
+    - tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
+    - usb: phy: mxs: remove CONFIG_USB_OTG condition for mxs_phy_is_otg_host()
+    - usb: dwc: ep0: Update request status in dwc3_ep0_stall_restart
+    - Revert "usb: dwc3: Soft reset phy on probe for host"
+    - Revert "usb: dwc3: don't reset device side if dwc3 was configured as host-
+      only"
+    - usb: chipidea: wait controller resume finished for wakeup irq
+    - usb: cdns3: fix uvc failure work since sg support enabled
+    - usb: cdns3: fix iso transfer error when mult is not zero
+    - usb: cdns3: Fix uvc fail when DMA cross 4k boundery since sg enabled
+    - Revert "usb: typec: class: fix typec_altmode_put_partner to put plugs"
+    - usb: typec: class: fix typec_altmode_put_partner to put plugs
+    - usb: mon: Fix atomicity violation in mon_bin_vma_fault
+    - serial: imx: Ensure that imx_uart_rs485_config() is called with enabled
+      clock
+    - ALSA: oxygen: Fix right channel of capture volume mixer
+    - ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx
+    - fbdev: flush deferred work in fb_deferred_io_fsync()
+    - scsi: mpi3mr: Refresh sdev queue depth after controller reset
+    - block: add check that partition length needs to be aligned with block size
+    - pwm: jz4740: Don't use dev_err_probe() in .request()
+    - io_uring/rw: ensure io->bytes_done is always initialized
+    - rootfs: Fix support for rootfstype= when root= is given
+    - Bluetooth: Fix atomicity violation in {min,max}_key_size_set
+    - bpf: Fix re-attachment branch in bpf_tracing_prog_attach
+    - iommu/arm-smmu-qcom: Add missing GMU entry to match table
+    - wifi: mt76: fix broken precal loading from MTD for mt7915
+    - wifi: rtlwifi: Remove bogus and dangerous ASPM disable/enable code
+    - wifi: rtlwifi: Convert LNKCTL change to PCIe cap RMW accessors
+    - wifi: mwifiex: configure BSSID consistently when starting AP
+    - PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support
+    - PCI: mediatek: Clear interrupt status before dispatching handler
+    - x86/kvm: Do not try to disable kvmclock if it was not enabled
+    - KVM: arm64: vgic-v4: Restore pending state on host userspace write
+    - KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cache
+    - iio: adc: ad7091r: Pass iio_dev to event handler
+    - HID: wacom: Correct behavior when processing some confidence == false
+      touches
+    - serial: sc16is7xx: add check for unsupported SPI modes during probe
+    - serial: sc16is7xx: set safe default SPI clock frequency
+    - iommu/dma: Trace bounce buffer usage when mapping buffers
+    - ARM: 9330/1: davinci: also select PINCTRL
+    - mfd: syscon: Fix null pointer dereference in of_syscon_register()
+    - leds: aw2013: Select missing dependency REGMAP_I2C
+    - mfd: intel-lpss: Fix the fractional clock divider flags
+    - mips: dmi: Fix early remap on MIPS32
+    - mips: Fix incorrect max_low_pfn adjustment
+    - riscv: Check if the code to patch lies in the exit section
+    - riscv: Fix module_alloc() that did not reset the linear mapping permissions
+    - MIPS: Alchemy: Fix an out-of-bound access in db1200_dev_setup()
+    - MIPS: Alchemy: Fix an out-of-bound access in db1550_dev_setup()
+    - power: supply: cw2015: correct time_to_empty units in sysfs
+    - power: supply: bq256xx: fix some problem in bq256xx_hw_init
+    - serial: 8250: omap: Don't skip resource freeing if
+      pm_runtime_resume_and_get() failed
+    - libapi: Add missing linux/types.h header to get the __u64 type on io.h
+    - software node: Let args be NULL in software_node_get_reference_args
+    - serial: imx: fix tx statemachine deadlock
+    - selftests/sgx: Fix uninitialized pointer dereference in error path
+    - selftests/sgx: Skip non X86_64 platform
+    - iio: adc: ad9467: Benefit from devm_clk_get_enabled() to simplify
+    - iio: adc: ad9467: fix reset gpio handling
+    - iio: adc: ad9467: don't ignore error codes
+    - iio: adc: ad9467: fix scale setting
+    - perf genelf: Set ELF program header addresses properly
+    - tty: change tty_write_lock()'s ndelay parameter to bool
+    - tty: early return from send_break() on TTY_DRIVER_HARDWARE_BREAK
+    - tty: don't check for signal_pending() in send_break()
+    - tty: use 'if' in send_break() instead of 'goto'
+    - usb: cdc-acm: return correct error code on unsupported break
+    - nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length
+    - nvmet-tcp: fix a crash in nvmet_req_complete()
+    - perf env: Avoid recursively taking env->bpf_progs.lock
+    - apparmor: avoid crash when parsed profile name is empty
+    - usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
+    - serial: imx: Correct clock error message in function probe()
+    - nvmet: re-fix tracing strncpy() warning
+    - nvmet-tcp: Fix the H2C expected PDU len calculation
+    - PCI: keystone: Fix race condition when initializing PHYs
+    - s390/pci: fix max size calculation in zpci_memcpy_toio()
+    - net: qualcomm: rmnet: fix global oob in rmnet_policy
+    - net: ethernet: ti: am65-cpsw: Fix max mtu to fit ethernet frames
+    - net: phy: micrel: populate .soft_reset for KSZ9131
+    - mptcp: mptcp_parse_option() fix for MPTCPOPT_MP_JOIN
+    - mptcp: drop unused sk in mptcp_get_options
+    - mptcp: strict validation before using mp_opt->hmac
+    - mptcp: use OPTION_MPTCP_MPJ_SYNACK in subflow_finish_connect()
+    - mptcp: use OPTION_MPTCP_MPJ_SYN in subflow_check_req()
+    - net: ravb: Fix dma_addr_t truncation in error case
+    - net: stmmac: ethtool: Fixed calltrace caused by unbalanced disable_irq_wake
+      calls
+    - bpf: Reject variable offset alu on PTR_TO_FLOW_KEYS
+    - net: dsa: vsc73xx: Add null pointer check to vsc73xx_gpio_probe
+    - netfilter: nf_tables: reject invalid set policy
+    - netfilter: nft_connlimit: move stateful fields out of expression data
+    - netfilter: nft_last: move stateful fields out of expression data
+    - netfilter: nft_quota: move stateful fields out of expression data
+    - netfilter: nft_limit: rename stateful structure
+    - netfilter: nft_limit: move stateful fields out of expression data
+    - netfilter: nf_tables: memcg accounting for dynamically allocated objects
+    - netfilter: nft_limit: do not ignore unsupported flags
+    - netfilter: nf_tables: do not allow mismatch field size and set key length
+    - netfilter: nf_tables: skip dead set elements in netlink dump
+    - netfilter: nf_tables: reject NFT_SET_CONCAT with not field length
+      description
+    - ipvs: avoid stat macros calls from preemptible context
+    - kdb: Fix a potential buffer overflow in kdb_local()
+    - ethtool: netlink: Add missing ethnl_ops_begin/complete
+    - mlxsw: spectrum_acl_erp: Fix error flow of pool allocation failure
+    - mlxsw: spectrum: Use 'bitmap_zalloc()' when applicable
+    - mlxsw: spectrum_acl_tcam: Add missing mutex_destroy()
+    - mlxsw: spectrum_acl_tcam: Make fini symmetric to init
+    - mlxsw: spectrum_acl_tcam: Reorder functions to avoid forward declarations
+    - mlxsw: spectrum_acl_tcam: Fix stack corruption
+    - selftests: mlxsw: qos_pfc: Adjust the test to support 8 lanes
+    - ipv6: mcast: fix data-race in ipv6_mc_down / mld_ifc_work
+    - i2c: s3c24xx: fix read transfers in polling mode
+    - i2c: s3c24xx: fix transferring more than one message in polling mode
+    - block: Remove special-casing of compound pages
+    - netfilter: nf_tables: typo NULL check in _clone() function
+    - netfilter: nft_connlimit: memleak if nf_ct_netns_get() fails
+    - netfilter: nft_limit: fix stateful object memory leak
+    - netfilter: nft_limit: Clone packet limits' cost value
+    - netfilter: nft_last: copy content when cloning expression
+    - netfilter: nft_quota: copy content when cloning expression
+    - arm64: dts: armada-3720-turris-mox: set irq type for RTC
+    - Revert "Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d""
+    - Linux 5.15.148
+
+  * CVE-2024-24855
+    - scsi: lpfc: Fix a possible data race in lpfc_unregister_fcf_rescan()
+
+  * performance: Scheduler: ratelimit updating of load_avg (LP: #2053251)
+    - sched/fair: Ratelimit update to tg->load_avg
+
+  * Jammy update: v5.15.147 upstream stable release (LP: #2054411)
+    - block: Don't invalidate pagecache for invalid falloc modes
+    - ALSA: hda/realtek: Fix mute and mic-mute LEDs for HP ProBook 440 G6
+    - Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"
+    - wifi: iwlwifi: pcie: don't synchronize IRQs from IRQ
+    - drm/bridge: ti-sn65dsi86: Never store more than msg->size bytes in AUX xfer
+    - nfc: llcp_core: Hold a ref to llcp_local->dev when holding a ref to
+      llcp_local
+    - octeontx2-af: Fix marking couple of structure as __packed
+    - drm/i915/dp: Fix passing the correct DPCD_REV for
+      drm_dp_set_phy_test_pattern
+    - i40e: Fix filter input checks to prevent config with invalid values
+    - igc: Report VLAN EtherType matching back to user
+    - igc: Check VLAN TCI mask
+    - igc: Check VLAN EtherType mask
+    - ASoC: fsl_rpmsg: Fix error handler with pm_runtime_enable
+    - mlxbf_gige: fix receive packet race condition
+    - net: sched: em_text: fix possible memory leak in em_text_destroy()
+    - r8169: Fix PCI error on system resume
+    - net: Implement missing getsockopt(SO_TIMESTAMPING_NEW)
+    - can: raw: add support for SO_TXTIME/SCM_TXTIME
+    - can: raw: add support for SO_MARK
+    - net-timestamp: extend SOF_TIMESTAMPING_OPT_ID to HW timestamps
+    - ARM: sun9i: smp: Fix array-index-out-of-bounds read in sunxi_mc_smp_init
+    - sfc: fix a double-free bug in efx_probe_filters
+    - net: bcmgenet: Fix FCS generation for fragmented skbuffs
+    - netfilter: nft_immediate: drop chain reference counter on error
+    - net: Save and restore msg_namelen in sock_sendmsg
+    - i40e: fix use-after-free in i40e_aqc_add_filters()
+    - ASoC: meson: g12a-toacodec: Validate written enum values
+    - ASoC: meson: g12a-tohdmitx: Validate written enum values
+    - ASoC: meson: g12a-toacodec: Fix event generation
+    - ASoC: meson: g12a-tohdmitx: Fix event generation for S/PDIF mux
+    - i40e: Restore VF MSI-X state during PCI reset
+    - igc: Fix hicredit calculation
+    - net/qla3xxx: fix potential memleak in ql_alloc_buffer_queues
+    - octeontx2-af: Don't enable Pause frames by default
+    - octeontx2-af: Set NIX link credits based on max LMAC
+    - octeontx2-af: Always configure NIX TX link credits based on max frame size
+    - octeontx2-af: Re-enable MAC TX in otx2_stop processing
+    - asix: Add check for usbnet_get_endpoints
+    - bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()
+    - net: Implement missing SO_TIMESTAMPING_NEW cmsg support
+    - selftests: secretmem: floor the memory size to the multiple of page_size
+    - mm/memory-failure: check the mapcount of the precise page
+    - firewire: ohci: suppress unexpected system reboot in AMD Ryzen machines and
+      ASM108x/VT630x PCIe cards
+    - x86/kprobes: fix incorrect return address calculation in
+      kprobe_emulate_call_indirect
+    - i2c: core: Fix atomic xfer check for non-preempt config
+    - mm: fix unmap_mapping_range high bits shift bug
+    - mmc: meson-mx-sdhc: Fix initialization frozen issue
+    - mmc: rpmb: fixes pause retune on all RPMB partitions.
+    - mmc: core: Cancel delayed work before releasing host
+    - mmc: sdhci-sprd: Fix eMMC init failure after hw reset
+    - ipv6: remove max_size check inline with ipv4
+    - perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
+    - kallsyms: Make module_kallsyms_on_each_symbol generally available
+    - tracing/kprobes: Fix symbol counting logic by looking at modules as well
+    - net: usb: ax88179_178a: remove redundant init code
+    - net: usb: ax88179_178a: move priv to driver_priv
+    - Linux 5.15.147
+
+  * CVE-2024-1085
+    - netfilter: nf_tables: check if catch-all set element is active in next
+      generation
+
+  * CVE-2023-23000
+    - phy: tegra: xusb: Fix return value of tegra_xusb_find_port_node function
+
+  * performance: mm/percpu-internal.h: Re-layout pcpu_chunk to mitigate false
+    sharing (LP: #2053152)
+    - percpu-internal/pcpu_chunk: re-layout pcpu_chunk structure to reduce false
+      sharing
+
+  * performance: address_space: add padding for i_map and i_mmap_rwsem to
+    mitigate a false sharing (LP: #2053069)
+    - fs/address_space: add alignment padding for i_map and i_mmap_rwsem to
+      mitigate a false sharing.
+
+  * cpufreq: intel_pstate: Enable HWP IO boost for all servers (LP: #2052817)
+    - cpufreq: intel_pstate: Enable HWP IO boost for all servers
+
+  * performance: mm/memcontrol.c: remove the redundant updating of
+    stats_flush_threshold (LP: #2052827)
+    - mm/memcontrol.c: remove the redundant updating of stats_flush_threshold
+
+  * Jammy update: v5.15.146 upstream stable release (LP: #2053212)
+    - ARM: dts: dra7: Fix DRA7 L3 NoC node register size
+    - ARM: OMAP2+: Fix null pointer dereference and memory leak in
+      omap_soc_device_init
+    - reset: Fix crash when freeing non-existent optional resets
+    - s390/vx: fix save/restore of fpu kernel context
+    - wifi: iwlwifi: pcie: add another missing bh-disable for rxq->lock
+    - wifi: mac80211: mesh_plink: fix matches_local logic
+    - net/mlx5e: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list()
+    - net/mlx5e: fix a potential double-free in fs_udp_create_groups
+    - net/mlx5: Fix fw tracer first block check
+    - net/mlx5e: Correct snprintf truncation handling for fw_version buffer used
+      by representors
+    - net: sched: ife: fix potential use-after-free
+    - ethernet: atheros: fix a memleak in atl1e_setup_ring_resources
+    - net/rose: fix races in rose_kill_by_device()
+    - net: mana: select PAGE_POOL
+    - net: check vlan filter feature in vlan_vids_add_by_dev() and
+      vlan_vids_del_by_dev()
+    - afs: Fix the dynamic root's d_delete to always delete unused dentries
+    - afs: Fix dynamic root lookup DNS check
+    - net: check dev->gso_max_size in gso_features_check()
+    - keys, dns: Allow key types (eg. DNS) to be reclaimed immediately on expiry
+    - keys, dns: Fix missing size check of V1 server-list header
+    - keys, dns: Fix size check of V1 server-list header
+    - afs: Fix overwriting of result of DNS query
+    - afs: Use refcount_t rather than atomic_t
+    - afs: Fix use-after-free due to get/remove race in volume tree
+    - ASoC: hdmi-codec: fix missing report for jack initial status
+    - i2c: aspeed: Handle the coalesced stop conditions with the start conditions.
+    - pinctrl: at91-pio4: use dedicated lock class for IRQ
+    - gpiolib: cdev: add gpio_device locking wrapper around gpio_ioctl()
+    - ksmbd: fix wrong name of SMB2_CREATE_ALLOCATION_SIZE
+    - drm/i915/mtl: limit second scaler vertical scaling in ver >= 14
+    - drm/i915: Relocate intel_atomic_setup_scalers()
+    - drm/i915: Fix intel_atomic_setup_scalers() plane_state handling
+    - smb: client: fix NULL deref in asn1_ber_decoder()
+    - smb: client: fix OOB in smb2_query_reparse_point()
+    - interconnect: Treat xlate() returning NULL node as an error
+    - iio: imu: inv_mpu6050: fix an error code problem in inv_mpu6050_read_raw
+    - Input: ipaq-micro-keys - add error handling for devm_kmemdup
+    - scsi: bnx2fc: Fix skb double free in bnx2fc_rcv()
+    - iio: common: ms_sensors: ms_sensors_i2c: fix humidity conversion time table
+    - iio: adc: ti_am335x_adc: Fix return value check of tiadc_request_dma()
+    - iio: triggered-buffer: prevent possible freeing of wrong buffer
+    - ALSA: usb-audio: Increase delay in MOTU M quirk
+    - wifi: cfg80211: Add my certificate
+    - wifi: cfg80211: fix certs build to not depend on file order
+    - USB: serial: ftdi_sio: update Actisense PIDs constant names
+    - USB: serial: option: add Quectel EG912Y module support
+    - USB: serial: option: add Foxconn T99W265 with new baseline
+    - USB: serial: option: add Quectel RM500Q R13 firmware support
+    - Bluetooth: hci_event: Fix not checking if HCI_OP_INQUIRY has been sent
+    - Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE
+    - Input: soc_button_array - add mapping for airplane mode button
+    - net: 9p: avoid freeing uninit memory in p9pdu_vreadf
+    - net: rfkill: gpio: set GPIO direction
+    - net: ks8851: Fix TX stall caused by TX buffer overrun
+    - dt-bindings: nvmem: mxs-ocotp: Document fsl,ocotp
+    - scsi: core: Always send batch on reset or error handling command
+    - tracing / synthetic: Disable events after testing in
+      synth_event_gen_test_init()
+    - bus: ti-sysc: Flush posted write only after srst_udelay
+    - gpio: dwapb: mask/unmask IRQ when disable/enale it
+    - lib/vsprintf: Fix %pfwf when current node refcount == 0
+    - KVM: arm64: vgic: Force vcpu vgic teardown on vcpu destroy
+    - x86/alternatives: Sync core before enabling interrupts
+    - fuse: share lookup state between submount and its parent
+    - ksmbd: have a dependency on cifs ARC4
+    - ksmbd: set epoch in create context v2 lease
+    - ksmbd: set v2 lease capability
+    - ksmbd: downgrade RWH lease caching state to RH for directory
+    - ksmbd: send v2 lease break notification for directory
+    - ksmbd: lazy v2 lease break on smb2_write()
+    - ksmbd: avoid duplicate opinfo_put() call on error of smb21_lease_break_ack()
+    - ksmbd: fix wrong allocation size update in smb2_open()
+    - ARM: dts: Fix occasional boot hang for am3 usb
+    - usb: fotg210-hcd: delete an incorrect bounds test
+    - ethernet: constify references to netdev->dev_addr in drivers
+    - net: usb: ax88179_178a: clean up pm calls
+    - net: usb: ax88179_178a: wol optimizations
+    - net: usb: ax88179_178a: avoid failed operations when device is disconnected
+    - device property: Add const qualifier to device_get_match_data() parameter
+    - spi: Introduce spi_get_device_match_data() helper
+    - iio: imu: adis16475: add spi_device_id table
+    - smb: client: fix OOB in SMB2_query_info_init()
+    - mm/filemap: avoid buffered read/write race to read inconsistent data
+    - ring-buffer: Fix wake ups when buffer_percent is set to 100
+    - tracing: Fix blocked reader of snapshot buffer
+    - ring-buffer: Remove useless update to write_stamp in rb_try_to_discard()
+    - ring-buffer: Fix slowpath of interrupted event
+    - dm-integrity: don't modify bio's immutable bio_vec in integrity_metadata()
+    - device property: Allow const parameter to dev_fwnode()
+    - bpf: Fix prog_array_map_poke_run map poke update
+    - Linux 5.15.146
+
+  * CVE-2023-46838
+    - xen-netback: don't produce zero-size SKB frags
+
+  * CVE-2024-1086
+    - netfilter: nf_tables: reject QUEUE/DROP verdict parameters
+
+  * disable Intel DMA remapping by default (LP: #1971699)
+    - [Config] update tracking bug for CONFIG_INTEL_IOMMU_DEFAULT_ON
+
+  * Validate connection interval to pass Bluetooth Test Suite (LP: #2052005)
+    - Bluetooth: Enforce validation on max value of connection interval
+
+  * Jammy update: v5.15.145 upstream stable release (LP: #2052406)
+    - ksmbd: use ksmbd_req_buf_next() in ksmbd_verify_smb_message()
+    - ksmdb: use cmd helper variable in smb2_get_ksmbd_tcon()
+    - ksmbd: Remove redundant 'flush_workqueue()' calls
+    - ksmbd: remove md4 leftovers
+    - ksmbd: remove smb2_buf_length in smb2_hdr
+    - ksmbd: remove smb2_buf_length in smb2_transform_hdr
+    - ksmbd: change LeaseKey data type to u8 array
+    - ksmbd: use oid registry functions to decode OIDs
+    - ksmbd: Remove unused parameter from smb2_get_name()
+    - ksmbd: Remove unused fields from ksmbd_file struct definition
+    - ksmbd: set both ipv4 and ipv6 in FSCTL_QUERY_NETWORK_INTERFACE_INFO
+    - ksmbd: Fix buffer_check_err() kernel-doc comment
+    - ksmbd: Fix smb2_set_info_file() kernel-doc comment
+    - ksmbd: Delete an invalid argument description in
+      smb2_populate_readdir_entry()
+    - ksmbd: Fix smb2_get_name() kernel-doc comment
+    - ksmbd: register ksmbd ib client with ib_register_client()
+    - ksmbd: set 445 port to smbdirect port by default
+    - ksmbd: smbd: call rdma_accept() under CM handler
+    - ksmbd: smbd: create MR pool
+    - ksmbd: smbd: change the default maximum read/write, receive size
+    - ksmbd: smbd: fix missing client's memory region invalidation
+    - ksmbd: smbd: validate buffer descriptor structures
+    - ksmbd: add support for key exchange
+    - ksmbd: use netif_is_bridge_port
+    - ksmbd: store fids as opaque u64 integers
+    - ksmbd: shorten experimental warning on loading the module
+    - ksmbd: Remove a redundant zeroing of memory
+    - ksmbd: replace usage of found with dedicated list iterator variable
+    - smb3: fix ksmbd bigendian bug in oplock break, and move its struct to
+      smbfs_common
+    - ksmbd: remove filename in ksmbd_file
+    - ksmbd: smbd: change prototypes of RDMA read/write related functions
+    - ksmbd: smbd: introduce read/write credits for RDMA read/write
+    - ksmbd: smbd: simplify tracking pending packets
+    - ksmbd: smbd: change the return value of get_sg_list
+    - ksmbd: smbd: handle multiple Buffer descriptors
+    - ksmbd: fix wrong smbd max read/write size check
+    - ksmbd: Fix some kernel-doc comments
+    - ksmbd: smbd: fix connection dropped issue
+    - ksmbd: smbd: relax the count of sges required
+    - ksmbd: smbd: Remove useless license text when SPDX-License-Identifier is
+      already used
+    - ksmbd: remove duplicate flag set in smb2_write
+    - ksmbd: remove unused ksmbd_share_configs_cleanup function
+    - ksmbd: use wait_event instead of schedule_timeout()
+    - ksmbd: request update to stale share config
+    - ksmbd: remove unnecessary generic_fillattr in smb2_open
+    - ksmbd: don't open-code file_path()
+    - ksmbd: don't open-code %pD
+    - ksmbd: constify struct path
+    - ksmbd: remove generic_fillattr use in smb2_open()
+    - ksmbd: casefold utf-8 share names and fix ascii lowercase conversion
+    - ksmbd: change security id to the one samba used for posix extension
+    - ksmbd: set file permission mode to match Samba server posix extension
+      behavior
+    - ksmbd: fill sids in SMB_FIND_FILE_POSIX_INFO response
+    - ksmbd: fix encryption failure issue for session logoff response
+    - ksmbd: set NTLMSSP_NEGOTIATE_SEAL flag to challenge blob
+    - ksmbd: decrease the number of SMB3 smbdirect server SGEs
+    - ksmbd: reduce server smbdirect max send/receive segment sizes
+    - ksmbd: hide socket error message when ipv6 config is disable
+    - ksmbd: make utf-8 file name comparison work in __caseless_lookup()
+    - ksmbd: call ib_drain_qp when disconnected
+    - ksmbd: validate share name from share config response
+    - ksmbd: replace one-element arrays with flexible-array members
+    - ksmbd: set SMB2_SESSION_FLAG_ENCRYPT_DATA when enforcing data encryption for
+      this share
+    - ksmbd: use F_SETLK when unlocking a file
+    - ksmbd: Fix resource leak in smb2_lock()
+    - ksmbd: Convert to use sysfs_emit()/sysfs_emit_at() APIs
+    - ksmbd: send proper error response in smb2_tree_connect()
+    - ksmbd: Implements sess->rpc_handle_list as xarray
+    - ksmbd: fix typo, syncronous->synchronous
+    - ksmbd: Remove duplicated codes
+    - ksmbd: update Kconfig to note Kerberos support and fix indentation
+    - ksmbd: Fix spelling mistake "excceed" -> "exceeded"
+    - ksmbd: Fix parameter name and comment mismatch
+    - ksmbd: fix possible memory leak in smb2_lock()
+    - ksmbd: fix wrong signingkey creation when encryption is AES256
+    - ksmbd: remove unused is_char_allowed function
+    - ksmbd: delete asynchronous work from list
+    - ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
+    - ksmbd: avoid out of bounds access in decode_preauth_ctxt()
+    - ksmbd: set NegotiateContextCount once instead of every inc
+    - ksmbd: avoid duplicate negotiate ctx offset increments
+    - ksmbd: remove unused compression negotiate ctx packing
+    - fs: introduce lock_rename_child() helper
+    - ksmbd: fix racy issue from using ->d_parent and ->d_name
+    - ksmbd: destroy expired sessions
+    - ksmbd: block asynchronous requests when making a delay on session setup
+    - ksmbd: fix racy issue from smb2 close and logoff with multichannel
+    - ksmbd: fix racy issue under cocurrent smb2 tree disconnect
+    - ksmbd: fix uninitialized pointer read in ksmbd_vfs_rename()
+    - ksmbd: fix uninitialized pointer read in smb2_create_link()
+    - ksmbd: fix multiple out-of-bounds read during context decoding
+    - ksmbd: fix UAF issue from opinfo->conn
+    - ksmbd: call putname after using the last component
+    - ksmbd: fix out-of-bound read in deassemble_neg_contexts()
+    - ksmbd: fix out-of-bound read in parse_lease_state()
+    - ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
+    - ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
+    - ksmbd: validate smb request protocol id
+    - ksmbd: add mnt_want_write to ksmbd vfs functions
+    - ksmbd: remove unused ksmbd_tree_conn_share function
+    - ksmbd: use kzalloc() instead of __GFP_ZERO
+    - ksmbd: return a literal instead of 'err' in ksmbd_vfs_kern_path_locked()
+    - ksmbd: Change the return value of ksmbd_vfs_query_maximal_access to void
+    - ksmbd: use kvzalloc instead of kvmalloc
+    - ksmbd: Replace the ternary conditional operator with min()
+    - ksmbd: fix out of bounds read in smb2_sess_setup
+    - ksmbd: add missing compound request handing in some commands
+    - ksmbd: Use struct_size() helper in ksmbd_negotiate_smb_dialect()
+    - ksmbd: Replace one-element array with flexible-array member
+    - ksmbd: Fix unsigned expression compared with zero
+    - ksmbd: check if a mount point is crossed during path lookup
+    - ksmbd: validate session id and tree id in compound request
+    - ksmbd: fix out of bounds in init_smb2_rsp_hdr()
+    - ksmbd: switch to use kmemdup_nul() helper
+    - ksmbd: add support for read compound
+    - ksmbd: fix wrong interim response on compound
+    - ksmbd: fix `force create mode' and `force directory mode'
+    - ksmbd: reduce descriptor size if remaining bytes is less than request size
+    - ksmbd: Fix one kernel-doc comment
+    - ksmbd: fix slub overflow in ksmbd_decode_ntlmssp_auth_blob()
+    - ksmbd: add missing calling smb2_set_err_rsp() on error
+    - ksmbd: remove experimental warning
+    - ksmbd: remove unneeded mark_inode_dirty in set_info_sec()
+    - ksmbd: fix passing freed memory 'aux_payload_buf'
+    - ksmbd: return invalid parameter error response if smb2 request is invalid
+    - ksmbd: check iov vector index in ksmbd_conn_write()
+    - ksmbd: fix race condition between session lookup and expire
+    - ksmbd: fix race condition with fp
+    - ksmbd: fix race condition from parallel smb2 logoff requests
+    - ksmbd: fix race condition from parallel smb2 lock requests
+    - ksmbd: fix race condition between tree conn lookup and disconnect
+    - ksmbd: fix wrong error response status by using set_smb2_rsp_status()
+    - ksmbd: fix Null pointer dereferences in ksmbd_update_fstate()
+    - ksmbd: fix potential double free on smb2_read_pipe() error path
+    - ksmbd: Remove unused field in ksmbd_user struct
+    - ksmbd: reorganize ksmbd_iov_pin_rsp()
+    - ksmbd: fix kernel-doc comment of ksmbd_vfs_setxattr()
+    - ksmbd: fix recursive locking in vfs helpers
+    - ksmbd: fix missing RDMA-capable flag for IPoIB device in
+      ksmbd_rdma_capable_netdev()
+    - ksmbd: add support for surrogate pair conversion
+    - ksmbd: no need to wait for binded connection termination at logoff
+    - ksmbd: fix kernel-doc comment of ksmbd_vfs_kern_path_locked()
+    - ksmbd: handle malformed smb1 message
+    - ksmbd: prevent memory leak on error return
+    - ksmbd: fix possible deadlock in smb2_open
+    - ksmbd: separately allocate ci per dentry
+    - ksmbd: move oplock handling after unlock parent dir
+    - ksmbd: release interim response after sending status pending response
+    - ksmbd: move setting SMB2_FLAGS_ASYNC_COMMAND and AsyncId
+    - ksmbd: don't update ->op_state as OPLOCK_STATE_NONE on error
+    - tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols
+    - kasan: disable kasan_non_canonical_hook() for HW tags
+    - Linux 5.15.145
+
+  * Jammy update: v5.15.144 upstream stable release (LP: #2052404)
+    - r8152: add vendor/device ID pair for D-Link DUB-E250
+    - r8152: add vendor/device ID pair for ASUS USB-C2500
+    - netfilter: nf_tables: fix 'exist' matching on bigendian arches
+    - mm/memory_hotplug: handle memblock_add_node() failures in
+      add_memory_resource()
+    - memblock: allow to specify flags with memblock_add_node()
+    - MIPS: Loongson64: Handle more memory types passed from firmware
+    - ksmbd: fix memory leak in smb2_lock()
+    - afs: Fix refcount underflow from error handling race
+    - HID: lenovo: Restrict detection of patched firmware only to USB cptkbd
+    - net: ipv6: support reporting otherwise unknown prefix flags in RTM_NEWPREFIX
+    - qca_debug: Prevent crash on TX ring changes
+    - qca_debug: Fix ethtool -G iface tx behavior
+    - qca_spi: Fix reset behavior
+    - atm: solos-pci: Fix potential deadlock on &cli_queue_lock
+    - atm: solos-pci: Fix potential deadlock on &tx_queue_lock
+    - net: vlan: introduce skb_vlan_eth_hdr()
+    - net: fec: correct queue selection
+    - octeontx2-af: fix a use-after-free in rvu_nix_register_reporters
+    - octeontx2-pf: Fix promisc mcam entry action
+    - octeontx2-af: Update RSS algorithm index
+    - qed: Fix a potential use-after-free in qed_cxt_tables_alloc
+    - net: Remove acked SYN flag from packet in the transmit queue correctly
+    - net: ena: Destroy correct number of xdp queues upon failure
+    - net: ena: Fix xdp drops handling due to multibuf packets
+    - net: ena: Fix XDP redirection error
+    - stmmac: dwmac-loongson: Make sure MDIO is initialized before use
+    - sign-file: Fix incorrect return values check
+    - vsock/virtio: Fix unsigned integer wrap around in
+      virtio_transport_has_space()
+    - dpaa2-switch: fix size of the dma_unmap
+    - net: stmmac: use dev_err_probe() for reporting mdio bus registration failure
+    - net: stmmac: Handle disabled MDIO busses from devicetree
+    - net: atlantic: fix double free in ring reinit logic
+    - cred: switch to using atomic_long_t
+    - fuse: dax: set fc->dax to NULL in fuse_dax_conn_free()
+    - ALSA: hda/hdmi: add force-connect quirk for NUC5CPYB
+    - ALSA: hda/hdmi: add force-connect quirks for ASUSTeK Z170 variants
+    - ALSA: hda/realtek: Apply mute LED quirk for HP15-db
+    - PCI: loongson: Limit MRRS to 256
+    - drm/mediatek: Add spinlock for setting vblank event in atomic_begin
+    - usb: aqc111: check packet for fixup for true limit
+    - stmmac: dwmac-loongson: Add architecture dependency
+    - [Config] updateconfigs for CONFIG_DWMAC_LOONGSON
+    - blk-throttle: fix lockdep warning of "cgroup_mutex or RCU read lock
+      required!"
+    - blk-cgroup: bypass blkcg_deactivate_policy after destroying
+    - bcache: avoid oversize memory allocation by small stripe_size
+    - bcache: remove redundant assignment to variable cur_idx
+    - bcache: add code comments for bch_btree_node_get() and
+      __bch_btree_node_alloc()
+    - bcache: avoid NULL checking to c->root in run_cache_set()
+    - platform/x86: intel_telemetry: Fix kernel doc descriptions
+    - HID: glorious: fix Glorious Model I HID report
+    - HID: add ALWAYS_POLL quirk for Apple kb
+    - HID: hid-asus: reset the backlight brightness level on resume
+    - HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
+    - asm-generic: qspinlock: fix queued_spin_value_unlocked() implementation
+    - net: usb: qmi_wwan: claim interface 4 for ZTE MF290
+    - HID: hid-asus: add const to read-only outgoing usb buffer
+    - btrfs: do not allow non subvolume root targets for snapshot
+    - soundwire: stream: fix NULL pointer dereference for multi_link
+    - ext4: prevent the normalized size from exceeding EXT_MAX_BLOCKS
+    - arm64: mm: Always make sw-dirty PTEs hw-dirty in pte_modify
+    - team: Fix use-after-free when an option instance allocation fails
+    - drm/amdgpu/sdma5.2: add begin/end_use ring callbacks
+    - ring-buffer: Fix memory leak of free page
+    - tracing: Update snapshot buffer on resize if it is allocated
+    - ring-buffer: Do not update before stamp when switching sub-buffers
+    - ring-buffer: Have saved event hold the entire event
+    - ring-buffer: Fix writing to the buffer with max_data_size
+    - ring-buffer: Fix a race in rb_time_cmpxchg() for 32 bit archs
+    - ring-buffer: Do not try to put back write_stamp
+    - USB: gadget: core: adjust uevent timing on gadget unbind
+    - powerpc/ftrace: Create a dummy stackframe to fix stack unwind
+    - powerpc/ftrace: Fix stack teardown in ftrace_no_trace
+    - r8152: avoid to change cfg for all devices
+    - r8152: remove rtl_vendor_mode function
+    - r8152: fix the autosuspend doesn't work
+    - Linux 5.15.144
+
+  * CVE-2023-32247
+    - ksmbd: destroy expired sessions
+
+  * CVE-2024-22705
+    - ksmbd: fix slab-out-of-bounds in smb_strndup_from_utf16()
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 05 Mar 2024 16:22:39 +0100
+
+linux (5.15.0-100.110) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-100.110 -proposed tracker (LP: #2052616)
+
+  * i915 regression introduced with 5.5 kernel (LP: #2044131)
+    - drm/i915: Skip some timing checks on BXT/GLK DSI transcoders
+
+  * Audio balancing setting doesn't work with the cirrus codec (LP: #2051050)
+    - ALSA: hda/cs8409: Suppress vmaster control for Dolphin models
+
+  * partproke is broken on empty loopback device (LP: #2049689)
+    - block: Move checking GENHD_FL_NO_PART to bdev_add_partition()
+
+  * CVE-2023-0340
+    - vhost: use kzalloc() instead of kmalloc() followed by memset()
+
+  * CVE-2023-51780
+    - atm: Fix Use-After-Free in do_vcc_ioctl
+
+  * CVE-2023-6915
+    - ida: Fix crash in ida_free when the bitmap is empty
+
+  * CVE-2024-0646
+    - net: tls, update curr on splice as well
+
+  * CVE-2024-0565
+    - smb: client: fix OOB in receive_encrypted_standard()
+
+  * CVE-2023-51781
+    - appletalk: Fix Use-After-Free in atalk_ioctl
+
+  * Jammy update: v5.15.143 upstream stable release (LP: #2050858)
+    - vdpa/mlx5: preserve CVQ vringh index
+    - hrtimers: Push pending hrtimers away from outgoing CPU earlier
+    - i2c: designware: Fix corrupted memory seen in the ISR
+    - netfilter: ipset: fix race condition between swap/destroy and kernel side
+      add/del/test
+    - tg3: Move the [rt]x_dropped counters to tg3_napi
+    - tg3: Increment tx_dropped in tg3_tso_bug()
+    - kconfig: fix memory leak from range properties
+    - drm/amdgpu: correct chunk_ptr to a pointer to chunk.
+    - platform/x86: asus-wmi: Adjust tablet/lidflip handling to use enum
+    - platform/x86: asus-wmi: Add support for ROG X13 tablet mode
+    - platform/x86: asus-wmi: Simplify tablet-mode-switch probing
+    - platform/x86: asus-wmi: Simplify tablet-mode-switch handling
+    - platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code
+    - of: dynamic: Fix of_reconfig_get_state_change() return value documentation
+    - platform/x86: wmi: Allow duplicate GUIDs for drivers that use struct
+      wmi_driver
+    - platform/x86: wmi: Skip blocks with zero instances
+    - ipv6: fix potential NULL deref in fib6_add()
+    - octeontx2-pf: Add missing mutex lock in otx2_get_pauseparam
+    - octeontx2-af: Check return value of nix_get_nixlf before using nixlf
+    - hv_netvsc: rndis_filter needs to select NLS
+    - r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
+    - r8152: Add RTL8152_INACCESSIBLE checks to more loops
+    - r8152: Add RTL8152_INACCESSIBLE to r8156b_wait_loading_flash()
+    - r8152: Add RTL8152_INACCESSIBLE to r8153_pre_firmware_1()
+    - r8152: Add RTL8152_INACCESSIBLE to r8153_aldps_en()
+    - mlxbf-bootctl: correctly identify secure boot with development keys
+    - platform/mellanox: Add null pointer checks for devm_kasprintf()
+    - platform/mellanox: Check devm_hwmon_device_register_with_groups() return
+      value
+    - arcnet: restoring support for multiple Sohard Arcnet cards
+    - net: stmmac: fix FPE events losing
+    - octeontx2-af: fix a use-after-free in rvu_npa_register_reporters
+    - i40e: Fix unexpected MFS warning message
+    - net: bnxt: fix a potential use-after-free in bnxt_init_tc
+    - ionic: fix snprintf format length warning
+    - ionic: Fix dim work handling in split interrupt mode
+    - ipv4: ip_gre: Avoid skb_pull() failure in ipgre_xmit()
+    - net: hns: fix fake link up on xge port
+    - octeontx2-af: Update Tx link register range
+    - netfilter: nf_tables: validate family when identifying table via handle
+    - netfilter: xt_owner: Fix for unsafe access of sk->sk_socket
+    - tcp: do not accept ACK of bytes we never sent
+    - bpf: sockmap, updating the sg structure should also update curr
+    - psample: Require 'CAP_NET_ADMIN' when joining "packets" group
+    - net: add missing kdoc for struct genl_multicast_group::flags
+    - drop_monitor: Require 'CAP_SYS_ADMIN' when joining "events" group
+    - tee: optee: Fix supplicant based device enumeration
+    - RDMA/hns: Fix unnecessary err return when using invalid congest control
+      algorithm
+    - RDMA/irdma: Do not modify to SQD on error
+    - RDMA/irdma: Add wait for suspend on SQD
+    - arm64: dts: rockchip: Expand reg size of vdec node for RK3399
+    - RDMA/rtrs-srv: Do not unconditionally enable irq
+    - RDMA/rtrs-clt: Start hb after path_up
+    - RDMA/rtrs-srv: Check return values while processing info request
+    - RDMA/rtrs-srv: Free srv_mr iu only when always_invalidate is true
+    - RDMA/rtrs-srv: Destroy path files after making sure no IOs in-flight
+    - RDMA/rtrs-clt: Fix the max_send_wr setting
+    - RDMA/rtrs-clt: Remove the warnings for req in_use check
+    - RDMA/bnxt_re: Correct module description string
+    - hwmon: (acpi_power_meter) Fix 4.29 MW bug
+    - hwmon: (nzxt-kraken2) Fix error handling path in kraken2_probe()
+    - ASoC: wm_adsp: fix memleak in wm_adsp_buffer_populate
+    - RDMA/core: Fix umem iterator when PAGE_SIZE is greater then HCA pgsz
+    - RDMA/irdma: Avoid free the non-cqp_request scratch
+    - arm64: dts: imx8mq: drop usb3-resume-missing-cas from usb
+    - arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
+    - ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
+    - tracing: Fix a warning when allocating buffered events fails
+    - scsi: be2iscsi: Fix a memleak in beiscsi_init_wrb_handle()
+    - ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
+    - ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
+    - ARM: dts: imx28-xea: Pass the 'model' property
+    - riscv: fix misaligned access handling of C.SWSP and C.SDSP
+    - md: introduce md_ro_state
+    - md: don't leave 'MD_RECOVERY_FROZEN' in error path of md_set_readonly()
+    - kprobes: consistent rcu api usage for kretprobe holder
+    - nvme-pci: Add sleep quirk for Kingston drives
+    - io_uring: fix mutex_unlock with unreferenced ctx
+    - ALSA: usb-audio: Add Pioneer DJM-450 mixer controls
+    - ALSA: pcm: fix out-of-bounds in snd_pcm_state_names
+    - nilfs2: fix missing error check for sb_set_blocksize call
+    - nilfs2: prevent WARNING in nilfs_sufile_set_segment_usage()
+    - checkstack: fix printed address
+    - tracing: Always update snapshot buffer size
+    - tracing: Disable snapshot buffer when stopping instance tracers
+    - tracing: Fix incomplete locking when disabling buffered events
+    - tracing: Fix a possible race when disabling buffered events
+    - packet: Move reference count in packet_sock to atomic_long_t
+    - regmap: fix bogus error on regcache_sync success
+    - platform/surface: aggregator: fix recv_buf() return value
+    - arm64: dts: mediatek: mt7622: fix memory node warning check
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: fix dsi unnecessary cells
+      properties
+    - arm64: dts: mediatek: mt8173-evb: Fix regulator-fixed node names
+    - arm64: dts: mediatek: mt8183: Fix unit address for scp reserved memory
+    - binder: fix memory leaks of spam and pending work
+    - kallsyms: Make kallsyms_on_each_symbol generally available
+    - coresight: etm4x: Make etm4_remove_dev() return void
+    - coresight: etm4x: Remove bogous __exit annotation for some functions
+    - misc: mei: client.c: return negative error code in mei_cl_write
+    - misc: mei: client.c: fix problem of return '-EOVERFLOW' in mei_cl_write
+    - ring-buffer: Force absolute timestamp on discard of event
+    - tracing: Set actual size after ring buffer resize
+    - tracing: Stop current tracer when resizing buffer
+    - r8169: fix rtl8125b PAUSE frames blasting when suspended
+    - mm: fix oops when filemap_map_pmd() without prealloc_pte
+    - io_uring/af_unix: disable sending io_uring over sockets
+    - platform/x86: asus-wmi: Fix kbd_dock_devid tablet-switch reporting
+    - docs/process/howto: Replace C89 with C11
+    - tools headers UAPI: Sync linux/perf_event.h with the kernel sources
+    - arm64: dts: mediatek: align thermal zone node names with dtschema
+    - arm64: dts: mediatek: mt8183: Move thermal-zones to the root node
+    - arm64: dts: mediatek: add missing space before {
+    - arm64: dts: mt8183: kukui: Fix underscores in node names
+    - gpiolib: sysfs: Fix error handling on failed export
+    - drm/amd/amdgpu: Fix warnings in amdgpu/amdgpu_display.c
+    - drm/amdgpu: correct the amdgpu runtime dereference usage count
+    - usb: gadget: f_hid: fix report descriptor allocation
+    - parport: Add support for Brainboxes IX/UC/PX parallel cards
+    - usb: typec: class: fix typec_altmode_put_partner to put plugs
+    - ARM: PL011: Fix DMA support
+    - serial: sc16is7xx: address RX timeout interrupt errata
+    - serial: 8250: 8250_omap: Clear UART_HAS_RHR_IT_DIS bit
+    - serial: 8250: 8250_omap: Do not start RX DMA on THRI interrupt
+    - serial: 8250_omap: Add earlycon support for the AM654 UART controller
+    - x86/CPU/AMD: Check vendor in the AMD microcode callback
+    - KVM: s390/mm: Properly reset no-dat
+    - KVM: SVM: Update EFER software model on CR0 trap for SEV-ES
+    - MIPS: Loongson64: Reserve vgabios memory on boot
+    - MIPS: Loongson64: Enable DMA noncoherent support
+    - cifs: Fix non-availability of dedup breaking generic/304
+    - smb: client: fix potential NULL deref in parse_dfs_referrals()
+    - devcoredump : Serialize devcd_del work
+    - devcoredump: Send uevent once devcd is ready
+    - Linux 5.15.143
+
+  * Intel E810-XXV - NETDEV WATCHDOG: (ice): transmit queue timed out
+    (LP: #2036239)
+    - ice: Add feature bitmap, helpers and a check for DSCP
+    - ice: Add driver support for firmware changes for LAG
+    - ice: alter feature support check for SRIOV and LAG
+
+  * Don't WARN_ON_ONCE() for a broken discovery table (LP: #2048404)
+    - perf/x86/uncore: Don't WARN_ON_ONCE() for a broken discovery table
+
+  * Reject connection when malformed L2CAP signal packet is received
+    (LP: #2047634)
+    - Bluetooth: L2CAP: Send reject on command corrupted request
+
+  * Jammy update: v5.15.142 upstream stable release (LP: #2050849)
+    - pinctrl: avoid reload of p state in list iteration
+    - firewire: core: fix possible memory leak in create_units()
+    - mmc: cqhci: Increase recovery halt timeout
+    - mmc: cqhci: Warn of halt or task clear failure
+    - mmc: cqhci: Fix task clearing in CQE error recovery
+    - mmc: block: Retry commands in CQE error recovery
+    - mmc: block: Do not lose cache flush during CQE error recovery
+    - mmc: block: Be sure to wait while busy in CQE error recovery
+    - ALSA: hda: Disable power-save on KONTRON SinglePC
+    - ALSA: hda/realtek: Headset Mic VREF to 100%
+    - ALSA: hda/realtek: Add supported ALC257 for ChromeOS
+    - dm-verity: align struct dm_verity_fec_io properly
+    - dm verity: don't perform FEC for failed readahead IO
+    - bcache: revert replacing IS_ERR_OR_NULL with IS_ERR
+    - iommu/vt-d: Add MTL to quirk list to skip TE disabling
+    - powerpc: Don't clobber f0/vs0 during fp|altivec register save
+    - parisc: Drop the HP-UX ENOSYM and EREMOTERELEASE error codes
+    - btrfs: ref-verify: fix memory leaks in btrfs_ref_tree_mod()
+    - btrfs: fix off-by-one when checking chunk map includes logical address
+    - btrfs: send: ensure send_fd is writable
+    - btrfs: make error messages more clear when getting a chunk map
+    - Input: xpad - add HyperX Clutch Gladiate Support
+    - vlan: introduce vlan_dev_free_egress_priority
+    - vlan: move dev_put into vlan_dev_uninit
+    - rcu: Avoid tracing a few functions executed in stop machine
+    - hv_netvsc: fix race of netvsc and VF register_netdevice
+    - USB: core: Change configuration warnings to notices
+    - usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
+    - dpaa2-eth: increase the needed headroom to account for alignment
+    - uapi: propagate __struct_group() attributes to the container union
+    - selftests/net: ipsec: fix constant out of range
+    - octeontx2-af: Fix possible buffer overflow
+    - net: stmmac: xgmac: Disable FPE MMC interrupts
+    - octeontx2-pf: Fix adding mbox work queue entry when num_vfs > 64
+    - Revert "workqueue: remove unused cancel_work()"
+    - r8169: prevent potential deadlock in rtl8169_close
+    - ravb: Fix races between ravb_tx_timeout_work() and net related ops
+    - net: ravb: Check return value of reset_control_deassert()
+    - net: ravb: Use pm_runtime_resume_and_get()
+    - net: ravb: Start TX queues after HW initialization succeeded
+    - net: ravb: Stop DMA in case of failures on ravb_open()
+    - perf intel-pt: Fix async branch flags
+    - selftests/resctrl: Add missing SPDX license to Makefile
+    - selftests/resctrl: Move _GNU_SOURCE define into Makefile
+    - smb3: fix touch -h of symlink
+    - ASoC: Intel: Move soc_intel_is_foo() helpers to a generic header
+    - ASoC: SOF: sof-pci-dev: use community key on all Up boards
+    - ASoC: SOF: sof-pci-dev: add parameter to override topology filename
+    - ASoC: SOF: sof-pci-dev: don't use the community key on APL Chromebooks
+    - ASoC: SOF: sof-pci-dev: Fix community key quirk detection
+    - fbdev: stifb: Make the STI next font pointer a 32-bit signed offset
+    - fs: add ctime accessors infrastructure
+    - smb3: fix caching of ctime on setxattr
+    - cpufreq: imx6q: don't warn for disabling a non-existing frequency
+    - cpufreq: imx6q: Don't disable 792 Mhz OPP unnecessarily
+    - iommu/vt-d: Omit devTLB invalidation requests when TES=0
+    - iommu/vt-d: Make context clearing consistent with context mapping
+    - mmc: core: add helpers mmc_regulator_enable/disable_vqmmc
+    - mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled
+    - r8169: disable ASPM in case of tx timeout
+    - r8169: fix deadlock on RTL8125 in jumbo mtu mode
+    - iomap: update ki_pos a little later in iomap_dio_complete
+    - Linux 5.15.142
+
+  * Jammy update: v5.15.141 upstream stable release (LP: #2050044)
+    - afs: Fix afs_server_list to be cleaned up with RCU
+    - afs: Make error on cell lookup failure consistent with OpenAFS
+    - drm/panel: boe-tv101wum-nl6: Fine tune the panel power sequence
+    - drm/panel: auo,b101uan08.3: Fine tune the panel power sequence
+    - drm/panel: simple: Fix Innolux G101ICE-L01 bus flags
+    - drm/panel: simple: Fix Innolux G101ICE-L01 timings
+    - wireguard: use DEV_STATS_INC()
+    - octeontx2-pf: Fix memory leak during interface down
+    - ata: pata_isapnp: Add missing error check for devm_ioport_map()
+    - drm/rockchip: vop: Fix color for RGB888/BGR888 format on VOP full
+    - HID: core: store the unique system identifier in hid_device
+    - HID: fix HID device resource race between HID core and debugging support
+    - ipv4: Correct/silence an endian warning in __ip_do_redirect
+    - net: usb: ax88179_178a: fix failed operations during ax88179_reset
+    - net/smc: avoid data corruption caused by decline
+    - arm/xen: fix xen_vcpu_info allocation alignment
+    - octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx
+      queue than its PF
+    - amd-xgbe: handle corner-case during sfp hotplug
+    - amd-xgbe: handle the corner-case during tx completion
+    - amd-xgbe: propagate the correct speed and duplex status
+    - net: axienet: Fix check for partial TX checksum
+    - afs: Return ENOENT if no cell DNS record can be found
+    - afs: Fix file locking on R/O volumes to operate in local mode
+    - nvmet: nul-terminate the NQNs passed in the connect command
+    - USB: dwc3: qcom: fix resource leaks on probe deferral
+    - USB: dwc3: qcom: fix ACPI platform device leak
+    - lockdep: Fix block chain corruption
+    - MIPS: KVM: Fix a build warning about variable set but not used
+    - media: camss: Replace hard coded value with parameter
+    - media: camss: sm8250: Virtual channels for CSID
+    - media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3
+    - media: qcom: camss: Fix csid-gen2 for test pattern generator
+    - ext4: add a new helper to check if es must be kept
+    - ext4: factor out __es_alloc_extent() and __es_free_extent()
+    - ext4: use pre-allocated es in __es_insert_extent()
+    - ext4: use pre-allocated es in __es_remove_extent()
+    - ext4: using nofail preallocation in ext4_es_remove_extent()
+    - ext4: using nofail preallocation in ext4_es_insert_delayed_block()
+    - ext4: using nofail preallocation in ext4_es_insert_extent()
+    - ext4: fix slab-use-after-free in ext4_es_insert_extent()
+    - ext4: make sure allocate pending entry not fail
+    - proc: sysctl: prevent aliased sysctls from getting passed to init
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CVA
+    - swiotlb-xen: provide the "max_mapping_size" method
+    - bcache: replace a mistaken IS_ERR() by IS_ERR_OR_NULL() in
+      btree_gc_coalesce()
+    - md: fix bi_status reporting in md_end_clone_io
+    - bcache: fixup multi-threaded bch_sectors_dirty_init() wake-up race
+    - io_uring/fs: consider link->flags when getting path for LINKAT
+    - s390/dasd: protect device queue against concurrent access
+    - USB: serial: option: add Luat Air72*U series products
+    - hv_netvsc: Fix race of register_netdevice_notifier and VF register
+    - hv_netvsc: Mark VF as slave before exposing it to user-mode
+    - dm-delay: fix a race between delay_presuspend and delay_bio
+    - bcache: check return value from btree_node_alloc_replacement()
+    - bcache: prevent potential division by zero error
+    - bcache: fixup init dirty data errors
+    - bcache: fixup lock c->root error
+    - usb: cdnsp: Fix deadlock issue during using NCM gadget
+    - USB: serial: option: add Fibocom L7xx modules
+    - USB: serial: option: fix FM101R-GL defines
+    - USB: serial: option: don't claim interface 4 for ZTE MF290
+    - usb: typec: tcpm: Skip hard reset when in error recovery
+    - USB: dwc2: write HCINT with INTMASK applied
+    - usb: dwc3: Fix default mode initialization
+    - usb: dwc3: set the dma max_seg_size
+    - USB: dwc3: qcom: fix software node leak on probe errors
+    - USB: dwc3: qcom: fix wakeup after probe deferral
+    - io_uring: fix off-by one bvec index
+    - Linux 5.15.141
+
+  * Jammy update: v5.15.140 upstream stable release (LP: #2050038)
+    - locking/ww_mutex/test: Fix potential workqueue corruption
+    - perf/core: Bail out early if the request AUX area is out of bound
+    - clocksource/drivers/timer-imx-gpt: Fix potential memory leak
+    - clocksource/drivers/timer-atmel-tcb: Fix initialization on SAM9 hardware
+    - workqueue: Provide one lock class key per work_on_cpu() callsite
+    - x86/mm: Drop the 4 MB restriction on minimal NUMA node memory size
+    - wifi: mac80211_hwsim: fix clang-specific fortify warning
+    - wifi: mac80211: don't return unset power in ieee80211_get_tx_power()
+    - atl1c: Work around the DMA RX overflow issue
+    - bpf: Detect IP == ksym.end as part of BPF program
+    - wifi: ath9k: fix clang-specific fortify warnings
+    - wifi: ath10k: fix clang-specific fortify warning
+    - net: annotate data-races around sk->sk_tx_queue_mapping
+    - net: annotate data-races around sk->sk_dst_pending_confirm
+    - wifi: ath10k: Don't touch the CE interrupt registers after power up
+    - Bluetooth: btusb: Add date->evt_skb is NULL check
+    - Bluetooth: Fix double free in hci_conn_cleanup
+    - platform/x86: thinkpad_acpi: Add battery quirk for Thinkpad X120e
+    - drm/komeda: drop all currently held locks if deadlock happens
+    - drm/amdkfd: Fix a race condition of vram buffer unref in svm code
+    - drm/amd/display: use full update for clip size increase of large plane
+      source
+    - string.h: add array-wrappers for (v)memdup_user()
+    - kernel: kexec: copy user-array safely
+    - kernel: watch_queue: copy user-array safely
+    - drm: vmwgfx_surface.c: copy user-array safely
+    - drm/msm/dp: skip validity check for DP CTS EDID checksum
+    - drm/amd: Fix UBSAN array-index-out-of-bounds for SMU7
+    - drm/amd: Fix UBSAN array-index-out-of-bounds for Polaris and Tonga
+    - drm/amdgpu: Fix potential null pointer derefernce
+    - drm/panel: fix a possible null pointer dereference
+    - drm/panel/panel-tpo-tpg110: fix a possible null pointer dereference
+    - drm/amdgpu/vkms: fix a possible null pointer dereference
+    - drm/panel: st7703: Pick different reset sequence
+    - drm/amdkfd: Fix shift out-of-bounds issue
+    - drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL
+    - arm64: dts: ls208xa: use a pseudo-bus to constrain usb dma size
+    - selftests/efivarfs: create-read: fix a resource leak
+    - ASoC: soc-card: Add storage for PCI SSID
+    - crypto: pcrypt - Fix hungtask for PADATA_RESET
+    - RDMA/hfi1: Use FIELD_GET() to extract Link Width
+    - scsi: hisi_sas: Set debugfs_dir pointer to NULL after removing debugfs
+    - scsi: ibmvfc: Remove BUG_ON in the case of an empty event pool
+    - fs/jfs: Add check for negative db_l2nbperpage
+    - fs/jfs: Add validity check for db_maxag and db_agpref
+    - jfs: fix array-index-out-of-bounds in dbFindLeaf
+    - jfs: fix array-index-out-of-bounds in diAlloc
+    - HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround
+    - ARM: 9320/1: fix stack depot IRQ stack filter
+    - ALSA: hda: Fix possible null-ptr-deref when assigning a stream
+    - PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields
+    - atm: iphase: Do PCI error checks on own line
+    - scsi: libfc: Fix potential NULL pointer dereference in fc_lport_ptp_setup()
+    - PCI: Use FIELD_GET() to extract Link Width
+    - PCI: Extract ATS disabling to a helper function
+    - PCI: Disable ATS for specific Intel IPU E2000 devices
+    - misc: pci_endpoint_test: Add Device ID for R-Car S4-8 PCIe controller
+    - PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk
+    - HID: Add quirk for Dell Pro Wireless Keyboard and Mouse KM5221W
+    - exfat: support handle zero-size directory
+    - tty: vcc: Add check for kstrdup() in vcc_probe()
+    - usb: gadget: f_ncm: Always set current gadget in ncm_bind()
+    - 9p/trans_fd: Annotate data-racy writes to file::f_flags
+    - 9p: v9fs_listxattr: fix %s null argument warning
+    - i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
+    - i2c: sun6i-p2wi: Prevent potential division by zero
+    - virtio-blk: fix implicit overflow on virtio_max_dma_size
+    - i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
+    - media: gspca: cpia1: shift-out-of-bounds in set_flicker
+    - media: vivid: avoid integer overflow
+    - gfs2: ignore negated quota changes
+    - gfs2: fix an oops in gfs2_permission
+    - media: cobalt: Use FIELD_GET() to extract Link Width
+    - media: ccs: Fix driver quirk struct documentation
+    - media: imon: fix access to invalid resource for the second interface
+    - drm/amd/display: Avoid NULL dereference of timing generator
+    - kgdb: Flush console before entering kgdb on panic
+    - i2c: dev: copy userspace array safely
+    - ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
+    - drm/qxl: prevent memory leak
+    - drm/amdgpu: fix software pci_unplug on some chips
+    - pwm: Fix double shift bug
+    - wifi: iwlwifi: Use FW rate for non-data frames
+    - tracing: Reuse logic from perf's get_recursion_context()
+    - tracing/perf: Add interrupt_context_level() helper
+    - sched/core: Optimize in_task() and in_interrupt() a bit
+    - media: cadence: csi2rx: Unregister v4l2 async notifier
+    - media: cec: meson: always include meson sub-directory in Makefile
+    - SUNRPC: ECONNRESET might require a rebind
+    - SUNRPC: Add an IS_ERR() check back to where it was
+    - NFSv4.1: fix SP4_MACH_CRED protection for pnfs IO
+    - SUNRPC: Fix RPC client cleaned up the freed pipefs dentries
+    - gfs2: Silence "suspicious RCU usage in gfs2_permission" warning
+    - mptcp: diag: switch to context structure
+    - mptcp: listen diag dump support
+    - net: inet: Remove count from inet_listen_hashbucket
+    - net: inet: Open code inet_hash2 and inet_unhash2
+    - net: inet: Retire port only listening_hash
+    - net: set SOCK_RCU_FREE before inserting socket into hashtable
+    - ipvlan: add ipvlan_route_v6_outbound() helper
+    - tty: Fix uninit-value access in ppp_sync_receive()
+    - net: hns3: fix add VLAN fail issue
+    - net: hns3: refine the definition for struct hclge_pf_to_vf_msg
+    - net: hns3: add byte order conversion for PF to VF mailbox message
+    - net: hns3: add barrier in vf mailbox reply process
+    - net: hns3: fix incorrect capability bit display for copper port
+    - net: hns3: fix variable may not initialized problem in hns3_init_mac_addr()
+    - net: hns3: fix VF reset fail issue
+    - net: hns3: fix VF wrong speed and duplex issue
+    - tipc: Fix kernel-infoleak due to uninitialized TLV value
+    - ppp: limit MRU to 64K
+    - xen/events: fix delayed eoi list handling
+    - ptp: annotate data-race around q->head and q->tail
+    - bonding: stop the device in bond_setup_by_slave()
+    - net: ethernet: cortina: Fix max RX frame define
+    - net: ethernet: cortina: Handle large frames
+    - net: ethernet: cortina: Fix MTU max setting
+    - af_unix: fix use-after-free in unix_stream_read_actor()
+    - netfilter: nf_conntrack_bridge: initialize err to 0
+    - netfilter: nf_tables: use the correct get/put helpers
+    - netfilter: nf_tables: add and use BE register load-store helpers
+    - netfilter: nf_tables: fix pointer math issue in nft_byteorder_eval()
+    - net: stmmac: fix rx budget limit check
+    - net/mlx5e: Remove incorrect addition of action fwd flag
+    - net/mlx5e: Move mod hdr allocation to a single place
+    - net/mlx5e: Refactor mod header management API
+    - net/mlx5e: Fix pedit endianness
+    - net/mlx5e: Reduce the size of icosq_str
+    - net/mlx5e: Check return value of snprintf writing to fw_version buffer for
+      representors
+    - macvlan: Don't propagate promisc change to lower dev in passthru
+    - tools/power/turbostat: Fix a knl bug
+    - tools/power/turbostat: Enable the C-state Pre-wake printing
+    - cifs: spnego: add ';' in HOST_KEY_LEN
+    - cifs: fix check of rc in function generate_smb3signingkey
+    - xfs: refactor buffer cancellation table allocation
+    - xfs: don't leak xfs_buf_cancel structures when recovery fails
+    - xfs: convert buf_cancel_table allocation to kmalloc_array
+    - xfs: use invalidate_lock to check the state of mmap_lock
+    - xfs: prevent a UAF when log IO errors race with unmount
+    - xfs: flush inode gc workqueue before clearing agi bucket
+    - xfs: fix use-after-free in xattr node block inactivation
+    - xfs: don't leak memory when attr fork loading fails
+    - xfs: fix intermittent hang during quotacheck
+    - xfs: add missing cmap->br_state = XFS_EXT_NORM update
+    - xfs: Fix false ENOSPC when performing direct write on a delalloc extent in
+      cow fork
+    - xfs: fix inode reservation space for removing transaction
+    - xfs: avoid a UAF when log intent item recovery fails
+    - xfs: fix exception caused by unexpected illegal bestcount in leaf dir
+    - xfs: fix memory leak in xfs_errortag_init
+    - xfs: Fix unreferenced object reported by kmemleak in xfs_sysfs_init()
+    - i915/perf: Fix NULL deref bugs with drm_dbg() calls
+    - media: venus: hfi: add checks to perform sanity on queue pointers
+    - powerpc/perf: Fix disabling BHRB and instruction sampling
+    - randstruct: Fix gcc-plugin performance mode to stay in group
+    - bpf: Fix check_stack_write_fixed_off() to correctly spill imm
+    - bpf: Fix precision tracking for BPF_ALU | BPF_TO_BE | BPF_END
+    - scsi: mpt3sas: Fix loop logic
+    - scsi: megaraid_sas: Increase register read retry rount from 3 to 30 for
+      selected registers
+    - scsi: qla2xxx: Fix system crash due to bad pointer access
+    - crypto: x86/sha - load modules based on CPU features
+    - x86/cpu/hygon: Fix the CPU topology evaluation for real
+    - KVM: x86: hyper-v: Don't auto-enable stimer on write from user-space
+    - KVM: x86: Ignore MSR_AMD64_TW_CFG access
+    - audit: don't take task_lock() in audit_exe_compare() code path
+    - audit: don't WARN_ON_ONCE(!current->mm) in audit_exe_compare()
+    - tty/sysrq: replace smp_processor_id() with get_cpu()
+    - hvc/xen: fix console unplug
+    - hvc/xen: fix error path in xen_hvc_init() to always register frontend driver
+    - hvc/xen: fix event channel handling for secondary consoles
+    - PCI/sysfs: Protect driver's D3cold preference from user space
+    - watchdog: move softlockup_panic back to early_param
+    - ACPI: resource: Do IRQ override on TongFang GMxXGxx
+    - arm64: Restrict CPU_BIG_ENDIAN to GNU as or LLVM IAS 15.x or newer
+    - parisc/pdc: Add width field to struct pdc_model
+    - clk: socfpga: Fix undefined behavior bug in struct stratix10_clock_data
+    - clk: qcom: ipq8074: drop the CLK_SET_RATE_PARENT flag from PLL clocks
+    - clk: qcom: ipq6018: drop the CLK_SET_RATE_PARENT flag from PLL clocks
+    - mmc: vub300: fix an error code
+    - mmc: sdhci_am654: fix start loop index for TAP value parsing
+    - PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
+    - PCI: exynos: Don't discard .remove() callback
+    - wifi: wilc1000: use vmm_table as array in wilc struct
+    - svcrdma: Drop connection after an RDMA Read error
+    - rcu/tree: Defer setting of jiffies during stall reset
+    - arm64: dts: qcom: ipq6018: Fix hwlock index for SMEM
+    - PM: hibernate: Use __get_safe_page() rather than touching the list
+    - PM: hibernate: Clean up sync_read handling in snapshot_write_next()
+    - rcu: kmemleak: Ignore kmemleak false positives when RCU-freeing objects
+    - btrfs: don't arbitrarily slow down delalloc if we're committing
+    - firmware: qcom_scm: use 64-bit calling convention only when client is 64-bit
+    - ACPI: FPDT: properly handle invalid FPDT subtables
+    - ima: annotate iint mutex to avoid lockdep false positive warnings
+    - ima: detect changes to the backing overlay file
+    - wifi: ath11k: fix temperature event locking
+    - wifi: ath11k: fix dfs radar event locking
+    - wifi: ath11k: fix htt pktlog locking
+    - mmc: meson-gx: Remove setting of CMD_CFG_ERROR
+    - genirq/generic_chip: Make irq_remove_generic_chip() irqdomain aware
+    - KEYS: trusted: Rollback init_trusted() consistently
+    - PCI: keystone: Don't discard .remove() callback
+    - PCI: keystone: Don't discard .probe() callback
+    - netfilter: nf_tables: split async and sync catchall in two functions
+    - selftests/resctrl: Remove duplicate feature check from CMT test
+    - selftests/resctrl: Reduce failures due to outliers in MBA/MBM tests
+    - ASoC: codecs: wsa-macro: fix uninitialized stack variables with name prefix
+    - jbd2: fix potential data lost in recovering journal raced with synchronizing
+      fs bdev
+    - quota: explicitly forbid quota files from being encrypted
+    - kernel/reboot: emergency_restart: Set correct system_state
+    - i2c: core: Run atomic i2c xfer when !preemptible
+    - tracing: Have the user copy of synthetic event address use correct context
+    - mcb: fix error handling for different scenarios when parsing
+    - dmaengine: stm32-mdma: correct desc prep when channel running
+    - s390/cmma: fix detection of DAT pages
+    - mm/cma: use nth_page() in place of direct struct page manipulation
+    - mm/memory_hotplug: use pfn math in place of direct struct page manipulation
+    - mtd: cfi_cmdset_0001: Byte swap OTP info
+    - i3c: master: cdns: Fix reading status register
+    - i3c: master: svc: fix race condition in ibi work thread
+    - i3c: master: svc: fix wrong data return when IBI happen during start frame
+    - i3c: master: svc: fix ibi may not return mandatory data byte
+    - i3c: master: svc: fix check wrong status register in irq handler
+    - i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
+    - parisc: Prevent booting 64-bit kernels on PA1.x machines
+    - parisc/pgtable: Do not drop upper 5 address bits of physical address
+    - xhci: Enable RPM on controllers that support low-power states
+    - ALSA: info: Fix potential deadlock at disconnection
+    - ALSA: hda/realtek - Add Dell ALC295 to pin fall back table
+    - ALSA: hda/realtek - Enable internal speaker of ASUS K6500ZC
+    - serial: meson: Use platform_get_irq() to get the interrupt
+    - tty: serial: meson: fix hard LOCKUP on crtscts mode
+    - regmap: Ensure range selector registers are updated after cache sync
+    - cpufreq: stats: Fix buffer overflow detection in trans_stats()
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0cb8:0xc559
+    - bluetooth: Add device 0bda:887b to device tables
+    - bluetooth: Add device 13d3:3571 to device tables
+    - Bluetooth: btusb: Add RTW8852BE device 13d3:3570 to device tables
+    - Bluetooth: btusb: Add 0bda:b85b for Fn-Link RTL8852BE
+    - ksmbd: fix slab out of bounds write in smb_inherit_dacl()
+    - arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
+    - arm64: dts: qcom: ipq6018: Fix tcsr_mutex register size
+    - powerpc/pseries/ddw: simplify enable_ddw()
+    - Revert ncsi: Propagate carrier gain/loss events to the NCSI controller
+    - Revert "i2c: pxa: move to generic GPIO recovery"
+    - lsm: fix default return value for vm_enough_memory
+    - lsm: fix default return value for inode_getsecctx
+    - sbsa_gwdt: Calculate timeout with 64-bit math
+    - i2c: designware: Disable TX_EMPTY irq while waiting for block length byte
+    - s390/ap: fix AP bus crash on early config change callback invocation
+    - net: ethtool: Fix documentation of ethtool_sprintf()
+    - net: dsa: lan9303: consequently nested-lock physical MDIO
+    - net: phylink: initialize carrier state at creation
+    - i2c: i801: fix potential race in i801_block_transaction_byte_by_byte
+    - f2fs: avoid format-overflow warning
+    - media: lirc: drop trailing space from scancode transmit
+    - media: sharp: fix sharp encoding
+    - media: venus: hfi_parser: Add check to keep the number of codecs within
+      range
+    - media: venus: hfi: fix the check to handle session buffer requirement
+    - media: venus: hfi: add checks to handle capabilities from firmware
+    - media: ccs: Correctly initialise try compose rectangle
+    - nfsd: fix file memleak on client_opens_release
+    - riscv: kprobes: allow writing to x0
+    - mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2
+    - mm: kmem: drop __GFP_NOFAIL when allocating objcg vectors
+    - r8169: fix network lost after resume on DASH systems
+    - mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of AER
+    - media: qcom: camss: Fix pm_domain_on sequence in probe
+    - media: qcom: camss: Fix vfe_get() error jump
+    - media: qcom: camss: Fix VFE-17x vfe_disable_output()
+    - media: qcom: camss: Fix missing vfe_lite clocks check
+    - ext4: apply umask if ACL support is disabled
+    - ext4: correct offset of gdb backup in non meta_bg group to update_backups
+    - ext4: correct return value of ext4_convert_meta_bg
+    - ext4: correct the start block of counting reserved clusters
+    - ext4: remove gdb backup copy for meta bg in setup_new_flex_group_blocks
+    - ext4: add missed brelse in update_backups
+    - drm/amd/pm: Handle non-terminated overdrive commands.
+    - drm/i915: Fix potential spectre vulnerability
+    - drm/amdgpu: don't use ATRM for external devices
+    - drm/amdgpu: fix error handling in amdgpu_bo_list_get()
+    - drm/amd/display: Change the DMCUB mailbox memory location from FB to inbox
+    - powerpc/powernv: Fix fortify source warnings in opal-prd.c
+    - tracing: Have trace_event_file have ref counters
+    - Input: xpad - add VID for Turtle Beach controllers
+    - driver core: Release all resources during unbind before updating device
+      links
+    - Linux 5.15.140
+
+  * CVE-2023-46862
+    - io_uring/fdinfo: lock SQ thread while retrieving thread cpu/pid
+
+  * Jammy update: v5.15.139 upstream stable release (LP: #2049432)
+    - iov_iter, x86: Be consistent about the __user tag on copy_mc_to_user()
+    - sched/uclamp: Ignore (util == 0) optimization in feec() when p_util_max = 0
+    - sched: Fix stop_one_cpu_nowait() vs hotplug
+    - vfs: fix readahead(2) on block devices
+    - writeback, cgroup: switch inodes with dirty timestamps to release dying
+      cgwbs
+    - x86/srso: Fix SBPB enablement for (possible) future fixed HW
+    - futex: Don't include process MM in futex key on no-MMU
+    - x86: Share definition of __is_canonical_address()
+    - x86/sev-es: Allow copy_from_kernel_nofault() in earlier boot
+    - x86/boot: Fix incorrect startup_gdt_descr.size
+    - pstore/platform: Add check for kstrdup
+    - genirq/matrix: Exclude managed interrupts in irq_matrix_allocated()
+    - i40e: fix potential memory leaks in i40e_remove()
+    - selftests/bpf: Test tail call counting with bpf2bpf and data on stack
+    - selftests/bpf: Correct map_fd to data_fd in tailcalls
+    - udp: add missing WRITE_ONCE() around up->encap_rcv
+    - tcp: call tcp_try_undo_recovery when an RTOd TFO SYNACK is ACKed
+    - gve: Use size_add() in call to struct_size()
+    - mlxsw: Use size_mul() in call to struct_size()
+    - tipc: Use size_add() in calls to struct_size()
+    - net: spider_net: Use size_add() in call to struct_size()
+    - wifi: rtw88: debug: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
+    - wifi: mt76: mt7603: rework/fix rx pse hang check
+    - mt76: dma: use kzalloc instead of devm_kzalloc for txwi
+    - mt76: add support for overriding the device used for DMA mapping
+    - mt76: pass original queue id from __mt76_tx_queue_skb to the driver
+    - wifi: mt76: mt7603: improve stuck beacon handling
+    - tcp_metrics: add missing barriers on delete
+    - tcp_metrics: properly set tp->snd_ssthresh in tcp_init_metrics()
+    - tcp_metrics: do not create an entry from tcp_init_metrics()
+    - wifi: rtlwifi: fix EDCA limit set by BT coexistence
+    - can: dev: can_restart(): don't crash kernel if carrier is OK
+    - can: dev: can_restart(): fix race condition between controller restart and
+      netif_carrier_on()
+    - can: dev: can_put_echo_skb(): don't crash kernel if can_priv::echo_skb is
+      accessed out of bounds
+    - PM / devfreq: rockchip-dfi: Make pmu regmap mandatory
+    - netfilter: nf_tables: Drop pointless memset when dumping rules
+    - thermal: core: prevent potential string overflow
+    - r8169: use tp_to_dev instead of open code
+    - r8169: fix rare issue with broken rx after link-down on RTL8125
+    - chtls: fix tp->rcv_tstamp initialization
+    - tcp: fix cookie_init_timestamp() overflows
+    - iwlwifi: pcie: adjust to Bz completion descriptor
+    - wifi: iwlwifi: call napi_synchronize() before freeing rx/tx queues
+    - wifi: iwlwifi: pcie: synchronize IRQs before NAPI
+    - wifi: iwlwifi: empty overflow queue during flush
+    - ACPI: sysfs: Fix create_pnp_modalias() and create_of_modalias()
+    - ipv6: avoid atomic fragment on GSO packets
+    - net: add DEV_STATS_READ() helper
+    - ipvlan: properly track tx_errors
+    - regmap: debugfs: Fix a erroneous check after snprintf()
+    - spi: tegra: Fix missing IRQ check in tegra_slink_probe()
+    - clk: qcom: clk-rcg2: Fix clock rate overflow for high parent frequencies
+    - clk: qcom: mmcc-msm8998: Don't check halt bit on some branch clks
+    - clk: qcom: mmcc-msm8998: Fix the SMMU GDSC
+    - clk: qcom: gcc-sm8150: Fix gcc_sdcc2_apps_clk_src
+    - clk: imx: Select MXC_CLK for CLK_IMX8QXP
+    - clk: imx: imx8mq: correct error handling path
+    - clk: imx: imx8qxp: Fix elcdif_pll clock
+    - clk: renesas: rzg2l: Simplify multiplication/shift logic
+    - clk: renesas: rzg2l: Use FIELD_GET() for PLL register fields
+    - clk: renesas: rzg2l: Fix computation formula
+    - spi: nxp-fspi: use the correct ioremap function
+    - clk: keystone: pll: fix a couple NULL vs IS_ERR() checks
+    - clk: ti: Add ti_dt_clk_name() helper to use clock-output-names
+    - clk: ti: Update pll and clockdomain clocks to use ti_dt_clk_name()
+    - clk: ti: Update component clocks to use ti_dt_clk_name()
+    - clk: ti: change ti_clk_register[_omap_hw]() API
+    - clk: ti: fix double free in of_ti_divider_clk_setup()
+    - clk: npcm7xx: Fix incorrect kfree
+    - clk: mediatek: clk-mt6765: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt6797: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt7629-eth: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt7629: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt2701: Add check for mtk_alloc_clk_data
+    - clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM
+    - platform/x86: wmi: Fix probe failure when failing to register WMI devices
+    - platform/x86: wmi: remove unnecessary initializations
+    - platform/x86: wmi: Fix opening of char device
+    - hwmon: (axi-fan-control) Fix possible NULL pointer dereference
+    - hwmon: (coretemp) Fix potentially truncated sysfs attribute name
+    - drm/rockchip: vop: Fix reset of state in duplicate state crtc funcs
+    - drm/rockchip: vop: Fix call to crtc reset helper
+    - drm/radeon: possible buffer overflow
+    - drm/mipi-dsi: Create devm device registration
+    - drm/mipi-dsi: Create devm device attachment
+    - drm/bridge: lt8912b: Switch to devm MIPI-DSI helpers
+    - drm/bridge: lt8912b: Register and attach our DSI device at probe
+    - drm/bridge: lt8912b: Add hot plug detection
+    - drm/bridge: lt8912b: Fix bridge_detach
+    - drm/bridge: lt8912b: Fix crash on bridge detach
+    - drm/bridge: lt8912b: Manually disable HPD only if it was enabled
+    - drm/bridge: lt8912b: Add missing drm_bridge_attach call
+    - drm/bridge: tc358768: Fix use of uninitialized variable
+    - drm/bridge: tc358768: Disable non-continuous clock mode
+    - drm/bridge: tc358768: Fix bit updates
+    - drm/amdkfd: fix some race conditions in vram buffer alloc/free of svm code
+    - drm/mediatek: Fix iommu fault by swapping FBs after updating plane state
+    - drm/mediatek: Fix iommu fault during crtc enabling
+    - drm/rockchip: cdn-dp: Fix some error handling paths in cdn_dp_probe()
+    - arm64/arm: xen: enlighten: Fix KPTI checks
+    - drm/rockchip: Fix type promotion bug in rockchip_gem_iommu_map()
+    - xen-pciback: Consider INTx disabled when MSI/MSI-X is enabled
+    - drm/msm/dsi: use msm_gem_kernel_put to free TX buffer
+    - drm: mediatek: mtk_dsi: Fix NO_EOT_PACKET settings/handling
+    - perf: hisi: Fix use-after-free when register pmu fails
+    - ARM: dts: renesas: blanche: Fix typo in GP_11_2 pin name
+    - arm64: dts: qcom: msm8916: Fix iommu local address range
+    - arm64: dts: qcom: msm8992-libra: drop duplicated reserved memory
+    - arm64: dts: qcom: sc7280: Add missing LMH interrupts
+    - arm64: dts: qcom: sdm845-mtp: fix WiFi configuration
+    - ARM64: dts: marvell: cn9310: Use appropriate label for spi1 pins
+    - arm64: dts: qcom: apq8016-sbc: Add missing ADV7533 regulators
+    - ARM: dts: qcom: mdm9615: populate vsdcc fixed regulator
+    - soc: qcom: llcc: Handle a second device without data corruption
+    - firmware: ti_sci: Mark driver as non removable
+    - firmware: arm_ffa: Assign the missing IDR allocation ID to the FFA device
+    - clk: scmi: Free scmi_clk allocated when the clocks with invalid info are
+      skipped
+    - arm64: dts: imx8qm-ss-img: Fix jpegenc compatible entry
+    - arm64: dts: imx8mm: Add sound-dai-cells to micfil node
+    - arm64: dts: imx8mn: Add sound-dai-cells to micfil node
+    - selftests/pidfd: Fix ksft print formats
+    - selftests/resctrl: Ensure the benchmark commands fits to its array
+    - crypto: hisilicon/hpre - Fix a erroneous check after snprintf()
+    - hwrng: geode - fix accessing registers
+    - RDMA/core: Use size_{add,sub,mul}() in calls to struct_size()
+    - scsi: ibmvfc: Fix erroneous use of rtas_busy_delay with hcall return code
+    - libnvdimm/of_pmem: Use devm_kstrdup instead of kstrdup and check its return
+      value
+    - nd_btt: Make BTT lanes preemptible
+    - crypto: caam/qi2 - fix Chacha20 + Poly1305 self test failure
+    - crypto: caam/jr - fix Chacha20 + Poly1305 self test failure
+    - crypto: qat - increase size of buffers
+    - hid: cp2112: Fix duplicate workqueue initialization
+    - ARM: 9321/1: memset: cast the constant byte to unsigned char
+    - ext4: move 'ix' sanity check to corrent position
+    - ASoC: fsl: mpc5200_dma.c: Fix warning of Function parameter or member not
+      described
+    - IB/mlx5: Fix rdma counter binding for RAW QP
+    - RDMA/hns: Fix uninitialized ucmd in hns_roce_create_qp_common()
+    - RDMA/hns: Fix signed-unsigned mixed comparisons
+    - RDMA/hns: The UD mode can only be configured with DCQCN
+    - ASoC: fsl: Fix PM disable depth imbalance in fsl_easrc_probe
+    - scsi: ufs: core: Leave space for '\0' in utf8 desc string
+    - RDMA/hfi1: Workaround truncation compilation error
+    - hid: cp2112: Fix IRQ shutdown stopping polling for all IRQs on chip
+    - sh: bios: Revive earlyprintk support
+    - Revert "HID: logitech-hidpp: add a module parameter to keep firmware
+      gestures"
+    - HID: logitech-hidpp: Remove HIDPP_QUIRK_NO_HIDINPUT quirk
+    - HID: logitech-hidpp: Don't restart IO, instead defer hid_connect() only
+    - HID: logitech-hidpp: Revert "Don't restart communication if not necessary"
+    - HID: logitech-hidpp: Move get_wireless_feature_index() check to
+      hidpp_connect_event()
+    - ASoC: Intel: Skylake: Fix mem leak when parsing UUIDs fails
+    - padata: Fix refcnt handling in padata_free_shell()
+    - crypto: qat - fix deadlock in backlog processing
+    - ASoC: ams-delta.c: use component after check
+    - mfd: core: Un-constify mfd_cell.of_reg
+    - mfd: core: Ensure disabled devices are skipped without aborting
+    - mfd: dln2: Fix double put in dln2_probe
+    - mfd: arizona-spi: Set pdata.hpdet_channel for ACPI enumerated devs
+    - leds: turris-omnia: Drop unnecessary mutex locking
+    - leds: turris-omnia: Do not use SMBUS calls
+    - leds: pwm: Don't disable the PWM when the LED should be off
+    - leds: trigger: ledtrig-cpu:: Fix 'output may be truncated' issue for 'cpu'
+    - f2fs: compress: fix to avoid use-after-free on dic
+    - f2fs: compress: fix to avoid redundant compress extension
+    - tty: tty_jobctrl: fix pid memleak in disassociate_ctty()
+    - livepatch: Fix missing newline character in klp_resolve_symbols()
+    - dmaengine: idxd: Register dsa_bus_type before registering idxd sub-drivers
+    - usb: dwc2: fix possible NULL pointer dereference caused by driver
+      concurrency
+    - usb: chipidea: Fix DMA overwrite for Tegra
+    - usb: chipidea: Simplify Tegra DMA alignment code
+    - dmaengine: ti: edma: handle irq_of_parse_and_map() errors
+    - misc: st_core: Do not call kfree_skb() under spin_lock_irqsave()
+    - tools: iio: iio_generic_buffer ensure alignment
+    - USB: usbip: fix stub_dev hub disconnect
+    - dmaengine: pxa_dma: Remove an erroneous BUG_ON() in pxad_free_desc()
+    - f2fs: fix to initialize map.m_pblk in f2fs_precache_extents()
+    - powerpc: Only define __parse_fpscr() when required
+    - modpost: fix tee MODULE_DEVICE_TABLE built on big-endian host
+    - powerpc/40x: Remove stale PTE_ATOMIC_UPDATES macro
+    - powerpc/xive: Fix endian conversion size
+    - powerpc/imc-pmu: Use the correct spinlock initializer.
+    - powerpc/pseries: fix potential memory leak in init_cpu_associativity()
+    - usb: host: xhci-plat: fix possible kernel oops while resuming
+    - perf machine: Avoid out of bounds LBR memory read
+    - perf hist: Add missing puts to hist__account_cycles
+    - 9p/net: fix possible memory leak in p9_check_errors()
+    - i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
+    - cxl/mem: Fix shutdown order
+    - rtc: pcf85363: fix wrong mask/val parameters in regmap_update_bits call
+    - pcmcia: cs: fix possible hung task and memory leak pccardd()
+    - pcmcia: ds: fix refcount leak in pcmcia_device_add()
+    - pcmcia: ds: fix possible name leak in error path in pcmcia_device_add()
+    - media: i2c: max9286: Fix some redundant of_node_put() calls
+    - media: bttv: fix use after free error due to btv->timeout timer
+    - media: s3c-camif: Avoid inappropriate kfree()
+    - media: vidtv: psi: Add check for kstrdup
+    - media: vidtv: mux: Add check and kfree for kstrdup
+    - media: cedrus: Fix clock/reset sequence
+    - media: dvb-usb-v2: af9035: fix missing unlock
+    - regmap: prevent noinc writes from clobbering cache
+    - pwm: sti: Reduce number of allocations and drop usage of chip_data
+    - pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
+    - Input: synaptics-rmi4 - fix use after free in rmi_unregister_function()
+    - llc: verify mac len before reading mac header
+    - hsr: Prevent use after free in prp_create_tagged_frame()
+    - tipc: Change nla_policy for bearer-related names to NLA_NUL_STRING
+    - bpf: Check map->usercnt after timer->timer is assigned
+    - inet: shrink struct flowi_common
+    - octeontx2-pf: Fix error codes
+    - octeontx2-pf: Fix holes in error code
+    - dccp: Call security_inet_conn_request() after setting IPv4 addresses.
+    - dccp/tcp: Call security_inet_conn_request() after setting IPv6 addresses.
+    - Fix termination state for idr_for_each_entry_ul()
+    - net: stmmac: xgmac: Enable support for multiple Flexible PPS outputs
+    - selftests: pmtu.sh: fix result checking
+    - net/smc: fix dangling sock under state SMC_APPFINCLOSEWAIT
+    - net/smc: allow cdc msg send rather than drop it with NULL sndbuf_desc
+    - net/smc: put sk reference if close work was canceled
+    - tg3: power down device only on SYSTEM_POWER_OFF
+    - block: remove unneeded return value of bio_check_ro()
+    - blk-core: use pr_warn_ratelimited() in bio_check_ro()
+    - r8169: respect userspace disabling IFF_MULTICAST
+    - i2c: iproc: handle invalid slave state
+    - netfilter: xt_recent: fix (increase) ipv6 literal buffer length
+    - netfilter: nft_redir: use `struct nf_nat_range2` throughout and deduplicate
+      eval call-backs
+    - netfilter: nat: fix ipv6 nat redirect with mapped and scoped addresses
+    - drm/syncobj: fix DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE
+    - ASoC: hdmi-codec: register hpd callback on component probe
+    - spi: spi-zynq-qspi: add spi-mem to driver kconfig dependencies
+    - fbdev: imsttfb: Fix error path of imsttfb_probe()
+    - fbdev: imsttfb: fix a resource leak in probe
+    - fbdev: fsl-diu-fb: mark wr_reg_wa() static
+    - tracing/kprobes: Fix the order of argument descriptions
+    - btrfs: use u64 for buffer sizes in the tree search ioctls
+    - Linux 5.15.139
+
+  * Jammy update: v5.15.138 upstream stable release (LP: #2049417)
+    - ASoC: codecs: wcd938x: fix resource leaks on bind errors
+    - ASoC: codecs: wcd938x: fix runtime PM imbalance on remove
+    - pinctrl: qcom: lpass-lpi: fix concurrent register updates
+    - tcp: remove dead code from tcp_sendmsg_locked()
+    - tcp: cleanup tcp_remove_empty_skb() use
+    - mptcp: more conservative check for zero probes
+    - mcb: Return actual parsed size when reading chameleon table
+    - mcb-lpc: Reallocate memory region to avoid memory overlapping
+    - virtio_balloon: Fix endless deflation and inflation on arm64
+    - virtio-mmio: fix memory leak of vm_dev
+    - vhost: Allow null msg.size on VHOST_IOTLB_INVALIDATE
+    - mm/page_alloc: correct start page when guard page debug is enabled
+    - mm/migrate: fix do_pages_move for compat pointers
+    - nfsd: lock_rename() needs both directories to live on the same fs
+    - drm/i915/pmu: Check if pmu is closed before stopping event
+    - vsock/virtio: factor our the code to initialize and delete VQs
+    - vsock/virtio: add support for device suspend/resume
+    - vsock/virtio: initialize the_virtio_vsock before using VQs
+    - drm/dp_mst: Fix NULL deref in get_mst_branch_device_by_guid_helper()
+    - firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels()
+    - r8169: fix the KCSAN reported data-race in rtl_tx() while reading tp->cur_tx
+    - r8169: fix the KCSAN reported data-race in rtl_tx while reading
+      TxDescArray[entry].opts1
+    - r8169: fix the KCSAN reported data race in rtl_rx while reading desc->opts1
+    - i40e: Fix I40E_FLAG_VF_VLAN_PRUNING value
+    - treewide: Spelling fix in comment
+    - igb: Fix potential memory leak in igb_add_ethtool_nfc_entry
+    - neighbour: fix various data-races
+    - igc: Fix ambiguity in the ethtool advertising
+    - net: ieee802154: adf7242: Fix some potential buffer overflow in
+      adf7242_stats_show()
+    - net: usb: smsc95xx: Fix uninit-value access in smsc95xx_read_reg
+    - r8152: Increase USB control msg timeout to 5000ms as per spec
+    - r8152: Run the unload routine if we have errors during probe
+    - r8152: Cancel hw_phy_work if we have an error in probe
+    - r8152: Release firmware if we have an error in probe
+    - tcp: fix wrong RTO timeout when received SACK reneging
+    - gtp: uapi: fix GTPA_MAX
+    - gtp: fix fragmentation needed check with gso
+    - i40e: Fix wrong check for I40E_TXR_FLAGS_WB_ON_ITR
+    - kasan: print the original fault addr when access invalid shadow
+    - iio: exynos-adc: request second interupt only when touchscreen mode is used
+    - iio: adc: xilinx-xadc: Don't clobber preset voltage/temperature thresholds
+    - iio: adc: xilinx-xadc: Correct temperature offset/scale for UltraScale
+    - i2c: muxes: i2c-mux-pinctrl: Use of_get_i2c_adapter_by_node()
+    - i2c: muxes: i2c-mux-gpmux: Use of_get_i2c_adapter_by_node()
+    - i2c: muxes: i2c-demux-pinctrl: Use of_get_i2c_adapter_by_node()
+    - i2c: stm32f7: Fix PEC handling in case of SMBUS transfers
+    - i2c: aspeed: Fix i2c bus hang in slave read
+    - tracing/kprobes: Fix the description of variable length arguments
+    - misc: fastrpc: Clean buffers on remote invocation failures
+    - nvmem: imx: correct nregs for i.MX6ULL
+    - nvmem: imx: correct nregs for i.MX6SLL
+    - nvmem: imx: correct nregs for i.MX6UL
+    - perf/core: Fix potential NULL deref
+    - sparc32: fix a braino in fault handling in csum_and_copy_..._user()
+    - clk: Sanitize possible_parent_show to Handle Return Value of
+      of_clk_get_parent_name
+    - iio: afe: rescale: reorder includes
+    - iio: afe: rescale: expose scale processing function
+    - iio: afe: rescale: add offset support
+    - iio: afe: rescale: Accept only offset channels
+    - gve: Fix GFP flags when allocing pages
+    - x86/i8259: Skip probing when ACPI/MADT advertises PCAT compatibility
+    - x86/mm: Simplify RESERVE_BRK()
+    - x86/mm: Fix RESERVE_BRK() for older binutils
+    - ext4: add two helper functions extent_logical_end() and pa_logical_end()
+    - ext4: fix BUG in ext4_mb_new_inode_pa() due to overflow
+    - ext4: avoid overlapping preallocations due to overflow
+    - objtool/x86: add missing embedded_insn check
+    - driver: platform: Add helper for safer setting of driver_override
+    - rpmsg: Constify local variable in field store macro
+    - rpmsg: Fix kfree() of static memory on setting driver_override
+    - rpmsg: Fix calling device_lock() on non-initialized device
+    - rpmsg: glink: Release driver_override
+    - rpmsg: Fix possible refcount leak in rpmsg_register_device_override()
+    - x86: Fix .brk attribute in linker script
+    - ASoC: simple-card: fixup asoc_simple_probe() error handling
+    - net: sched: cls_u32: Fix allocation size in u32_init()
+    - irqchip/riscv-intc: Mark all INTC nodes as initialized
+    - irqchip/stm32-exti: add missing DT IRQ flag translation
+    - dmaengine: ste_dma40: Fix PM disable depth imbalance in d40_probe
+    - powerpc/85xx: Fix math emulation exception
+    - Input: synaptics-rmi4 - handle reset delay when using SMBus trsnsport
+    - fbdev: atyfb: only use ioremap_uc() on i386 and ia64
+    - fs/ntfs3: Add ckeck in ni_update_parent()
+    - fs/ntfs3: Write immediately updated ntfs state
+    - fs/ntfs3: Use kvmalloc instead of kmalloc(... __GFP_NOWARN)
+    - fs/ntfs3: Fix possible NULL-ptr-deref in ni_readpage_cmpr()
+    - fs/ntfs3: Fix NULL pointer dereference on error in attr_allocate_frame()
+    - fs/ntfs3: Fix directory element type detection
+    - fs/ntfs3: Avoid possible memory leak
+    - spi: npcm-fiu: Fix UMA reads when dummy.nbytes == 0
+    - netfilter: nfnetlink_log: silence bogus compiler warning
+    - ASoC: rt5650: fix the wrong result of key button
+    - drm/ttm: Reorder sys manager cleanup step
+    - fbdev: uvesafb: Call cn_del_callback() at the end of uvesafb_exit()
+    - scsi: mpt3sas: Fix in error path
+    - platform/mellanox: mlxbf-tmfifo: Fix a warning message
+    - net: chelsio: cxgb4: add an error code check in t4_load_phy_fw
+    - r8152: Check for unplug in rtl_phy_patch_request()
+    - r8152: Check for unplug in r8153b_ups_en() / r8153c_ups_en()
+    - powerpc/mm: Fix boot crash with FLATMEM
+    - can: isotp: set max PDU size to 64 kByte
+    - can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
+    - can: isotp: check CAN address family in isotp_bind()
+    - can: isotp: handle wait_event_interruptible() return values
+    - can: isotp: add local echo tx processing and tx without FC
+    - can: isotp: isotp_bind(): do not validate unused address information
+    - can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior
+    - drm/amd: Move helper for dynamic speed switch check out of smu13
+    - drm/amd: Disable ASPM for VI w/ all Intel systems
+    - PCI: Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device
+    - usb: storage: set 1.50 as the lower bcdDevice for older "Super Top"
+      compatibility
+    - usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
+    - usb: raw-gadget: properly handle interrupted requests
+    - tty: n_gsm: fix race condition in status line change on dead connections
+    - tty: 8250: Remove UC-257 and UC-431
+    - tty: 8250: Add support for additional Brainboxes UC cards
+    - tty: 8250: Add support for Brainboxes UP cards
+    - tty: 8250: Add support for Intashield IS-100
+    - tty: 8250: Fix port count of PX-257
+    - tty: 8250: Fix up PX-803/PX-857
+    - tty: 8250: Add support for additional Brainboxes PX cards
+    - tty: 8250: Add support for Intashield IX cards
+    - tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
+    - misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
+    - ALSA: hda: intel-dsp-config: Fix JSL Chromebook quirk detection
+    - Linux 5.15.138
+
+  * Jammy update: v5.15.137 upstream stable release (LP: #2049350)
+    - lib/Kconfig.debug: do not enable DEBUG_PREEMPT by default
+    - Documentation: sysctl: align cells in second content column
+    - xfs: don't expose internal symlink metadata buffers to the vfs
+    - Bluetooth: hci_event: Ignore NULL link key
+    - Bluetooth: Reject connection with the device which has same BD_ADDR
+    - Bluetooth: Fix a refcnt underflow problem for hci_conn
+    - Bluetooth: vhci: Fix race when opening vhci device
+    - Bluetooth: hci_event: Fix coding style
+    - Bluetooth: avoid memcmp() out of bounds warning
+    - ice: fix over-shifted variable
+    - ice: reset first in crash dump kernels
+    - nfc: nci: fix possible NULL pointer dereference in send_acknowledge()
+    - regmap: fix NULL deref on lookup
+    - KVM: x86: Mask LVTPC when handling a PMI
+    - tcp: check mptcp-level constraints for backlog coalescing
+    - fs/ntfs3: Fix possible null-pointer dereference in hdr_find_e()
+    - fs/ntfs3: fix panic about slab-out-of-bounds caused by ntfs_list_ea()
+    - fs/ntfs3: fix deadlock in mark_as_free_ex
+    - netfilter: nft_payload: fix wrong mac header matching
+    - drm/i915: Retry gtt fault when out of fence registers
+    - ASoC: codecs: wcd938x-sdw: fix use after free on driver unbind
+    - ASoC: codecs: wcd938x-sdw: fix runtime PM imbalance on probe errors
+    - ASoC: codecs: wcd938x: drop bogus bind error handling
+    - ASoC: codecs: wcd938x: fix unbind tear down order
+    - qed: fix LL2 RX buffer allocation
+    - xfrm: fix a data-race in xfrm_gen_index()
+    - xfrm: interface: use DEV_STATS_INC()
+    - net: ipv4: fix return value check in esp_remove_trailer
+    - net: ipv6: fix return value check in esp_remove_trailer
+    - net: rfkill: gpio: prevent value glitch during probe
+    - tcp: fix excessive TLP and RACK timeouts from HZ rounding
+    - tcp: tsq: relax tcp_small_queue_check() when rtx queue contains a single skb
+    - tun: prevent negative ifindex
+    - ipv4: fib: annotate races around nh->nh_saddr_genid and nh->nh_saddr
+    - net: usb: smsc95xx: Fix an error code in smsc95xx_reset()
+    - i40e: prevent crash on probe if hw registers have invalid values
+    - net: dsa: bcm_sf2: Fix possible memory leak in bcm_sf2_mdio_register()
+    - bonding: Return pointer to data after pull on skb
+    - net/sched: sch_hfsc: upgrade 'rt' to 'sc' when it becomes a inner curve
+    - neighbor: tracing: Move pin6 inside CONFIG_IPV6=y section
+    - netfilter: nft_set_rbtree: .deactivate fails if element has expired
+    - netfilter: nf_tables: do not remove elements if set backend implements
+      .abort
+    - netfilter: nf_tables: revert do not remove elements if set backend
+      implements .abort
+    - net: pktgen: Fix interface flags printing
+    - selftests/mm: fix awk usage in charge_reserved_hugetlb.sh and
+      hugetlb_reparenting_test.sh that may cause error
+    - serial: 8250: omap: Fix imprecise external abort for omap_8250_pm()
+    - serial: 8250_omap: Fix errors with no_console_suspend
+    - iio: Un-inline iio_buffer_enabled()
+    - iio: core: Hide read accesses to iio_dev->currentmode
+    - iio: core: introduce iio_device_{claim|release}_buffer_mode() APIs
+    - iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
+    - iio: adc: ad7192: Correct reference voltage
+    - perf: Add irq and exception return branch types
+    - perf/x86: Move branch classifier
+    - perf/x86/lbr: Filter vsyscall addresses
+    - drm/atomic-helper: relax unregistered connector check
+    - powerpc/32s: Remove capability to disable KUEP at boottime
+    - powerpc/32s: Do kuep_lock() and kuep_unlock() in assembly
+    - powerpc/47x: Fix 47x syscall return crash
+    - mctp: Allow local delivery to the null EID
+    - mctp: perform route lookups under a RCU read-side lock
+    - nfp: flower: avoid rmmod nfp crash issues
+    - ksmbd: not allow to open file if delelete on close bit is set
+    - ARM: dts: ti: omap: Fix noisy serial with overrun-throttle-ms for mapphone
+    - fs-writeback: do not requeue a clean inode having skipped pages
+    - btrfs: return -EUCLEAN for delayed tree ref with a ref count not equals to 1
+    - btrfs: initialize start_slot in btrfs_log_prealloc_extents
+    - i2c: mux: Avoid potential false error message in i2c_mux_add_adapter
+    - overlayfs: set ctime when setting mtime and atime
+    - gpio: timberdale: Fix potential deadlock on &tgpio->lock
+    - ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
+    - ata: libata-eh: Fix compilation warning in ata_eh_link_report()
+    - tracing: relax trace_event_eval_update() execution with cond_resched()
+    - wifi: mwifiex: Sanity check tlv_len and tlv_bitmap_len
+    - wifi: iwlwifi: Ensure ack flag is properly cleared.
+    - HID: holtek: fix slab-out-of-bounds Write in holtek_kbd_input_event
+    - Bluetooth: btusb: add shutdown function for QCA6174
+    - Bluetooth: Avoid redundant authentication
+    - Bluetooth: hci_core: Fix build warnings
+    - wifi: cfg80211: Fix 6GHz scan configuration
+    - wifi: mac80211: allow transmitting EAPOL frames with tainted key
+    - wifi: cfg80211: avoid leaking stack data into trace
+    - regulator/core: Revert "fix kobject release warning and memory leak in
+      regulator_register()"
+    - sky2: Make sure there is at least one frag_addr available
+    - ipv4/fib: send notify when delete source address routes
+    - drm: panel-orientation-quirks: Add quirk for One Mix 2S
+    - btrfs: fix some -Wmaybe-uninitialized warnings in ioctl.c
+    - btrfs: error out when COWing block using a stale transaction
+    - btrfs: error when COWing block from a root that is being deleted
+    - btrfs: error out when reallocating block for defrag using a stale
+      transaction
+    - HID: multitouch: Add required quirk for Synaptics 0xcd7e device
+    - platform/x86: touchscreen_dmi: Add info for the Positivo C4128B
+    - net/mlx5: Handle fw tracer change ownership event based on MTRC
+    - Bluetooth: hci_event: Fix using memcmp when comparing keys
+    - net: introduce a function to check if a netdev name is in use
+    - net: move from strlcpy with unused retval to strscpy
+    - net: fix ifname in netlink ntf during netns move
+    - mtd: rawnand: qcom: Unmap the right resource upon probe failure
+    - mtd: rawnand: pl353: Ensure program page operations are successful
+    - mtd: rawnand: marvell: Ensure program page operations are successful
+    - mtd: rawnand: arasan: Ensure program page operations are successful
+    - mtd: spinand: micron: correct bitmask for ecc status
+    - mtd: physmap-core: Restore map_rom fallback
+    - mmc: mtk-sd: Use readl_poll_timeout_atomic in msdc_reset_hw
+    - mmc: core: sdio: hold retuning if sdio in 1-bit mode
+    - pNFS: Fix a hang in nfs4_evict_inode()
+    - NFSv4.1: fixup use EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - ACPI: irq: Fix incorrect return value in acpi_register_gsi()
+    - nvme-pci: add BOGUS_NID for Intel 0a54 device
+    - nvme-rdma: do not try to stop unallocated queues
+    - USB: serial: option: add Telit LE910C4-WWX 0x1035 composition
+    - USB: serial: option: add entry for Sierra EM9191 with new firmware
+    - USB: serial: option: add Fibocom to DELL custom modem FM101R-GL
+    - s390/pci: fix iommu bitmap allocation
+    - selftests/ftrace: Add new test case which checks non unique symbol
+    - s390/cio: fix a memleak in css_alloc_subchannel
+    - platform/surface: platform_profile: Propagate error if profile registration
+      fails
+    - platform/x86: asus-wmi: Change ASUS_WMI_BRN_DOWN code from 0x20 to 0x2e
+    - platform/x86: asus-wmi: Map 0x2a code, Ignore 0x2b and 0x2c events
+    - gpio: vf610: set value before the direction to avoid a glitch
+    - ASoC: pxa: fix a memory leak in probe()
+    - serial: 8250: omap: Move uart_write() inside PM section
+    - phy: mapphone-mdm6600: Fix runtime disable on probe
+    - phy: mapphone-mdm6600: Fix runtime PM for remove
+    - phy: mapphone-mdm6600: Fix pinctrl_pm handling for sleep pins
+    - Bluetooth: hci_sock: fix slab oob read in create_monitor_event
+    - Bluetooth: hci_sock: Correctly bounds check and pad HCI_MON_NEW_INDEX name
+    - xfrm6: fix inet6_dev refcount underflow problem
+    - Linux 5.15.137
+
+  * CVE-2023-51782
+    - net/rose: Fix Use-After-Free in rose_ioctl
+
+  * CVE-2023-51779
+    - Bluetooth: af_bluetooth: Fix Use-After-Free in bt_sock_recvmsg
+
+  * CVE-2023-22995
+    - usb: dwc3: dwc3-qcom: Add missing platform_device_put() in
+      dwc3_qcom_acpi_register_core
+
+  * CVE-2023-4134
+    - Input: cyttsp4_core - change del_timer_sync() to timer_shutdown_sync()
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 02 Feb 2024 14:05:20 +0100
+
+linux (5.15.0-94.104) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-94.104 -proposed tracker (LP: #2048777)
+
+  * [SRU] Duplicate Device_dax ids Created and hence Probing is Failing.
+    (LP: #2028158)
+    - device-dax: Fix duplicate 'hmem' device registration
+
+  * Add ODM driver f81604 usb-can (LP: #2045387)
+    - can: usb: f81604: add Fintek F81604 support
+    - [Config] updateconfigs for ODM drivers CONFIG_CAN_F81604
+
+  * Add ODM driver gpio-m058ssan (LP: #2045386)
+    - SAUCE: ODM: gpio: add M058SSAN gpio driver
+    - [Config] updateconfigs for ODM drivers CONFIG_GPIO_M058SSAN
+
+  * Add ODM driver rtc-pcf85263 (LP: #2045385)
+    - SAUCE: ODM: rtc: add PCF85263 RTC driver
+    - [Config] updateconfigs for ODM drivers CONFIG_RTC_DRV_PCF85263
+
+  * AppArmor patch for mq-posix interface is missing in jammy (LP: #2045384)
+    - SAUCE: (no-up) apparmor: reserve mediation classes
+    - SAUCE: (no-up) apparmor: Add fine grained mediation of posix mqueues
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 09 Jan 2024 15:51:37 +0100
+
+linux (5.15.0-93.103) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-93.103 -proposed tracker (LP: #2048330)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] remove helper scripts
+    - [Packaging] update annotations scripts
+    - debian/dkms-versions -- update from kernel-versions (main/2024.01.08)
+
+  * Hotplugging SCSI disk in QEMU VM fails (LP: #2047382)
+    - Revert "PCI: acpiphp: Reassign resources on bridge if necessary"
+
+  * CVE-2023-6622
+    - netfilter: nf_tables: bail out on mismatching dynset and set expressions
+
+  * CVE-2024-0193
+    - netfilter: nf_tables: skip set commit for deleted/destroyed sets
+
+  * CVE-2023-6040
+    - netfilter: nf_tables: Reject tables of unsupported family
+
+  * Patches needed for AmpereOne (arm64) (LP: #2044192)
+    - clocksource/arm_arch_timer: Add build-time guards for unhandled register
+      accesses
+    - clocksource/drivers/arm_arch_timer: Drop CNT*_TVAL read accessors
+    - clocksource/drivers/arm_arch_timer: Extend write side of timer register
+      accessors to u64
+    - clocksource/drivers/arm_arch_timer: Move system register timer programming
+      over to CVAL
+    - clocksource/drivers/arm_arch_timer: Move drop _tval from erratum function
+      names
+    - clocksource/drivers/arm_arch_timer: Fix MMIO base address vs callback
+      ordering issue
+    - clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL
+    - clocksource/drivers/arm_arch_timer: Advertise 56bit timer to the core code
+    - clocksource/drivers/arm_arch_timer: Work around broken CVAL implementations
+    - clocksource/drivers/arm_arch_timer: Remove any trace of the TVAL programming
+      interface
+    - clocksource/drivers/arm_arch_timer: Drop unnecessary ISB on CVAL programming
+    - clocksource/drivers/arm_arch_timer: Fix masking for high freq counters
+    - clocksource/drivers/arch_arm_timer: Move workaround synchronisation around
+
+  * Add quirk to disable i915 fastboot on B&R PC (LP: #2047630)
+    - SAUCE: i915: force disable fastboot quirk
+
+  * Some machines can't pass the pm-graph test (LP: #2046217)
+    - wifi: iwlwifi: pcie: rescan bus if no parent
+
+  * Sound: Add rtl quirk of M90-Gen5 (LP: #2046105)
+    - ALSA: hda/realtek: Enable headset on Lenovo M90 Gen5
+
+  * linux tools packages for derived kernels refuse to install simultaneously
+    due to libcpupower name collision (LP: #2035971)
+    - [Packaging] Statically link libcpupower into cpupower tool
+
+  * [Debian] autoreconstruct - Do not generate chmod -x for deleted  files
+    (LP: #2045562)
+    - [Debian] autoreconstruct - Do not generate chmod -x for deleted files
+
+  * CVE-2023-6931
+    - perf/core: Add a new read format to get a number of lost samples
+    - perf: Fix perf_event_validate_size()
+    - perf: Fix perf_event_validate_size() lockdep splat
+
+  * CVE-2023-6932
+    - ipv4: igmp: fix refcnt uaf issue when receiving igmp query packet
+
+  * CVE-2023-6606
+    - smb: client: fix OOB in smbCalcSize()
+
+  * CVE-2023-6817
+    - netfilter: nft_set_pipapo: skip inactive elements during set walk
+
+  * Jammy update: v5.15.136 upstream stable release (LP: #2046008)
+    - iommu/vt-d: Avoid memory allocation in iommu_suspend()
+    - scsi: core: Use a structure member to track the SCSI command submitter
+    - scsi: core: Rename scsi_mq_done() into scsi_done() and export it
+    - scsi: ib_srp: Call scsi_done() directly
+    - RDMA/srp: Do not call scsi_done() from srp_abort()
+    - RDMA/cxgb4: Check skb value for failure to allocate
+    - perf/arm-cmn: Fix the unhandled overflow status of counter 4 to 7
+    - of: overlay: Reorder struct fragment fields kerneldoc
+    - platform/x86: think-lmi: Fix reference leak
+    - platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section
+      mismatch warning
+    - lib/test_meminit: fix off-by-one error in test_pages()
+    - HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect
+    - quota: Fix slow quotaoff
+    - net: prevent address rewrite in kernel_bind()
+    - ALSA: usb-audio: Fix microphone sound on Opencomm2 Headset
+    - KEYS: trusted: allow use of kernel RNG for key material
+    - KEYS: trusted: Remove redundant static calls usage
+    - drm/msm/dp: do not reinitialize phy unless retry during link training
+    - drm/msm/dsi: skip the wait for video mode done if not applicable
+    - drm/msm/dsi: fix irq_of_parse_and_map() error checking
+    - drm/msm/dpu: change _dpu_plane_calc_bw() to use u64 to avoid overflow
+    - ravb: Fix up dma_free_coherent() call in ravb_remove()
+    - ravb: Fix use-after-free issue in ravb_tx_timeout_work()
+    - ieee802154: ca8210: Fix a potential UAF in ca8210_probe
+    - mlxsw: fix mlxsw_sp2_nve_vxlan_learning_set() return type
+    - eth: remove copies of the NAPI_POLL_WEIGHT define
+    - xen-netback: use default TX queue size for vifs
+    - riscv, bpf: Factor out emit_call for kernel and bpf context
+    - riscv, bpf: Sign-extend return values
+    - drm/vmwgfx: fix typo of sizeof argument
+    - bpf: Fix verifier log for async callback return values
+    - net: macsec: indicate next pn update when offloading
+    - net: phy: mscc: macsec: reject PN update requests
+    - ixgbe: fix crash with empty VF macvlan list
+    - net/mlx5e: Again mutually exclude RX-FCS and RX-port-timestamp
+    - net: nfc: fix races in nfc_llcp_sock_get() and nfc_llcp_sock_get_sn()
+    - pinctrl: renesas: rzn1: Enable missing PINMUX
+    - nfc: nci: assert requested protocol is valid
+    - workqueue: Override implicit ordered attribute in
+      workqueue_apply_unbound_cpumask()
+    - net: add sysctl accept_ra_min_rtr_lft
+    - net: change accept_ra_min_rtr_lft to affect all RA lifetimes
+    - net: release reference to inet6_dev pointer
+    - media: mtk-jpeg: Fix use after free bug due to uncanceled work
+    - dmaengine: stm32-mdma: abort resume if no ongoing transfer
+    - xhci: Keep interrupt disabled in initialization until host is running.
+    - usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
+    - net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read
+    - usb: dwc3: Soft reset phy on probe for host
+    - usb: cdns3: Modify the return value of cdns_set_active () to void when
+      CONFIG_PM_SLEEP is disabled
+    - usb: musb: Get the musb_qh poniter after musb_giveback
+    - usb: musb: Modify the "HWVers" register address
+    - iio: pressure: bmp280: Fix NULL pointer exception
+    - iio: pressure: dps310: Adjust Timeout Settings
+    - iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
+    - drm/amdgpu: add missing NULL check
+    - drm/amd/display: Don't set dpms_off for seamless boot
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA
+    - x86/cpu: Fix AMD erratum #1485 on Zen4-based CPUs
+    - mcb: remove is_added flag from mcb_device struct
+    - thunderbolt: Workaround an IOMMU fault on certain systems with Intel Maple
+      Ridge
+    - thunderbolt: Check that lane 1 is in CL0 before enabling lane bonding
+    - libceph: use kernel_connect()
+    - ceph: fix incorrect revoked caps assert in ceph_fill_file_size()
+    - ceph: fix type promotion bug on 32bit systems
+    - Input: powermate - fix use-after-free in powermate_config_complete
+    - Input: psmouse - fix fast_reconnect function for PS/2 mode
+    - Input: xpad - add PXN V900 support
+    - Input: i8042 - add Fujitsu Lifebook E5411 to i8042 quirk table
+    - Input: goodix - ensure int GPIO is in input for gpio_count == 1 &&
+      gpio_int_idx == 0 case
+    - tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
+    - cgroup: Remove duplicates in cgroup v1 tasks file
+    - counter: microchip-tcb-capture: Fix the use of internal GCLK logic
+    - usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
+    - usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
+    - usb: cdnsp: Fixes issue with dequeuing not queued requests
+    - x86/alternatives: Disable KASAN in apply_alternatives()
+    - dmaengine: idxd: use spin_lock_irqsave before wait_event_lock_irq
+    - dmaengine: mediatek: Fix deadlock caused by synchronize_irq()
+    - powerpc/8xx: Fix pte_access_permitted() for PAGE_NONE
+    - powerpc/64e: Fix wrong test in __ptep_test_and_clear_young()
+    - arm64: report EL1 UNDEFs better
+    - arm64: die(): pass 'err' as long
+    - arm64: consistently pass ESR_ELx to die()
+    - arm64: rework FPAC exception handling
+    - arm64: rework BTI exception handling
+    - arm64: allow kprobes on EL0 handlers
+    - arm64: split EL0/EL1 UNDEF handlers
+    - arm64: factor out EL1 SSBS emulation hook
+    - arm64: factor insn read out of call_undef_hook()
+    - arm64: rework EL0 MRS emulation
+    - arm64: armv8_deprecated: fold ops into insn_emulation
+    - arm64: armv8_deprecated move emulation functions
+    - arm64: armv8_deprecated: move aarch32 helper earlier
+    - arm64: armv8_deprecated: rework deprected instruction handling
+    - arm64: armv8_deprecated: fix unused-function error
+    - usb: hub: Guard against accesses to uninitialized BOS descriptors
+    - eth: remove remaining copies of the NAPI_POLL_WEIGHT define
+    - Linux 5.15.136
+
+  * Jammy update: v5.15.135 upstream stable release (LP: #2045809)
+    - spi: zynqmp-gqspi: Convert to platform remove callback returning void
+    - spi: zynqmp-gqspi: fix clock imbalance on probe failure
+    - ASoC: soc-utils: Export snd_soc_dai_is_dummy() symbol
+    - ASoC: tegra: Fix redundant PLLA and PLLA_OUT0 updates
+    - NFS: Cleanup unused rpc_clnt variable
+    - NFS: rename nfs_client_kset to nfs_kset
+    - NFSv4: Fix a state manager thread deadlock regression
+    - ring-buffer: remove obsolete comment for free_buffer_page()
+    - ring-buffer: Fix bytes info in per_cpu buffer stats
+    - arm64: Avoid repeated AA64MMFR1_EL1 register read on pagefault path
+    - iommu/arm-smmu-v3: Set TTL invalidation hint better
+    - iommu/arm-smmu-v3: Avoid constructing invalid range commands
+    - rbd: move rbd_dev_refresh() definition
+    - rbd: decouple header read-in from updating rbd_dev->header
+    - rbd: decouple parent info read-in from updating rbd_dev
+    - rbd: take header_rwsem in rbd_dev_refresh() only when updating
+    - block: fix use-after-free of q->q_usage_counter
+    - scsi: zfcp: Fix a double put in zfcp_port_enqueue()
+    - qed/red_ll2: Fix undefined behavior bug in struct qed_ll2_info
+    - wifi: mwifiex: Fix tlv_buf_left calculation
+    - net: replace calls to sock->ops->connect() with kernel_connect()
+    - net: prevent rewrite of msg_name in sock_sendmsg()
+    - drm/amd: Fix detection of _PR3 on the PCIe root port
+    - arm64: Add Cortex-A520 CPU part definition
+    - HID: sony: Fix a potential memory leak in sony_probe()
+    - ubi: Refuse attaching if mtd's erasesize is 0
+    - wifi: iwlwifi: dbg_ini: fix structure packing
+    - iwlwifi: avoid void pointer arithmetic
+    - wifi: iwlwifi: mvm: Fix a memory corruption issue
+    - wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
+    - bpf: Fix tr dereferencing
+    - drivers/net: process the result of hdlc_open() and add call of hdlc_close()
+      in uhdlc_close()
+    - wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
+    - regmap: rbtree: Fix wrong register marked as in-cache when creating new node
+    - ima: Finish deprecation of IMA_TRUSTED_KEYRING Kconfig
+    - [Config] updateconfigs for IMA_BLACKLIST_KEYRING
+    - scsi: target: core: Fix deadlock due to recursive locking
+    - ima: rework CONFIG_IMA dependency block
+    - NFSv4: Fix a nfs4_state_manager() race
+    - bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
+    - modpost: add missing else to the "of" check
+    - net: fix possible store tearing in neigh_periodic_work()
+    - ipv4, ipv6: Fix handling of transhdrlen in __ip{,6}_append_data()
+    - ptp: ocp: Fix error handling in ptp_ocp_device_init
+    - net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent
+    - net: usb: smsc75xx: Fix uninit-value access in __smsc75xx_read_reg
+    - net: nfc: llcp: Add lock when modifying device list
+    - net: ethernet: ti: am65-cpsw: Fix error code in
+      am65_cpsw_nuss_init_tx_chns()
+    - ibmveth: Remove condition to recompute TCP header checksum.
+    - netfilter: handle the connecting collision properly in
+      nf_conntrack_proto_sctp
+    - netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
+    - ipv4: Set offload_failed flag in fibmatch results
+    - net: stmmac: dwmac-stm32: fix resume on STM32 MCU
+    - tipc: fix a potential deadlock on &tx->lock
+    - tcp: fix quick-ack counting to count actual ACKs of new data
+    - tcp: fix delayed ACKs for MSS boundary condition
+    - sctp: update transport state when processing a dupcook packet
+    - sctp: update hb timer immediately after users change hb_interval
+    - HID: sony: remove duplicate NULL check before calling usb_free_urb()
+    - HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit
+    - dm zoned: free dmz->ddev array in dmz_put_zoned_devices
+    - RDMA/core: Require admin capabilities to set system parameters
+    - of: dynamic: Fix potential memory leak in of_changeset_action()
+    - IB/mlx4: Fix the size of a buffer in add_port_entries()
+    - gpio: aspeed: fix the GPIO number passed to pinctrl_gpio_set_config()
+    - gpio: pxa: disable pinctrl calls for MMP_GPIO
+    - RDMA/cma: Initialize ib_sa_multicast structure to 0 when join
+    - RDMA/cma: Fix truncation compilation warning in make_cma_ports
+    - RDMA/uverbs: Fix typo of sizeof argument
+    - RDMA/siw: Fix connection failure handling
+    - RDMA/mlx5: Fix NULL string error
+    - ksmbd: fix uaf in smb20_oplock_break_ack
+    - parisc: Restore __ldcw_align for PA-RISC 2.0 processors
+    - xen/events: replace evtchn_rwlock with RCU
+    - Linux 5.15.135
+
+  * CVE-2023-46813
+    - x86/sev: Disable MMIO emulation from user mode
+    - x86/sev: Check IOBM for IOIO exceptions from user-space
+    - x86/sev: Check for user-space IOIO pointing to kernel space
+
+  * CVE-2023-6111
+    - netfilter: nf_tables: remove catchall element in GC sync path
+
+  * Change in trace file leads to test timeout in ftrace tests on 5.15 ARM64
+    (LP: #2029405)
+    - selftests/ftrace: Stop tracing while reading the trace file by default
+
+  * Fix ADL: System enabled AHCI can't get into s0ix when attached ODD
+    (LP: #2037493)
+    - ata: ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list
+
+  * Kernel doesn't compile with CONFIG_IMA (LP: #2041842)
+    - SAUCE: LSM: Fix typo in ima_filter_rule_match struct argument
+
+  * CVE-2023-32252
+    - ksmbd: add smb-direct shutdown
+    - ksmbd: Implements sess->ksmbd_chann_list as xarray
+    - ksmbd: fix racy issue from session setup and logoff
+
+  * Jammy update: v5.15.134 upstream stable release (LP: #2044023)
+    - NFS: Use the correct commit info in nfs_join_page_group()
+    - NFS: More fixes for nfs_direct_write_reschedule_io()
+    - NFS/pNFS: Report EINVAL errors from connect() to the server
+    - SUNRPC: Mark the cred for revalidation if the server rejects it
+    - NFSv4.1: use EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - NFSv4.1: fix pnfs MDS=DS session trunking
+    - tracing: Make trace_marker{,_raw} stream-like
+    - tracing: Increase trace array ref count on enable and filter files
+    - ata: ahci: Drop pointless VPRINTK() calls and convert the remaining ones
+    - ata: libahci: clear pending interrupt status
+    - ext4: scope ret locally in ext4_try_to_trim_range()
+    - ext4: change s_last_trim_minblks type to unsigned long
+    - ext4: replace the traditional ternary conditional operator with with
+      max()/min()
+    - ext4: move setting of trimmed bit into ext4_try_to_trim_range()
+    - ext4: do not let fstrim block system suspend
+    - tracing: Have event inject files inc the trace array ref count
+    - netfilter: nft_set_rbtree: use read spinlock to avoid datapath contention
+    - netfilter: nft_set_pipapo: call nft_trans_gc_queue_sync() in catchall GC
+    - netfilter: nft_set_pipapo: stop GC iteration if GC transaction allocation
+      fails
+    - netfilter: nft_set_hash: try later when GC hits EAGAIN on iteration
+    - netfilter: nf_tables: fix memleak when more than 255 elements expired
+    - ASoC: meson: spdifin: start hw on dai probe
+    - netfilter: nf_tables: disallow element removal on anonymous sets
+    - bpf: Avoid deadlock when using queue and stack maps from NMI
+    - selftests: tls: swap the TX and RX sockets in some tests
+    - net/core: Fix ETH_P_1588 flow dissector
+    - ASoC: imx-audmix: Fix return error with devm_clk_get()
+    - iavf: do not process adminq tasks when __IAVF_IN_REMOVE_TASK is set
+    - i40e: Add VF VLAN pruning
+    - i40e: Fix VF VLAN offloading when port VLAN is configured
+    - ionic: fix 16bit math issue when PAGE_SIZE >= 64KB
+    - igc: Fix infinite initialization loop with early XDP redirect
+    - powerpc/perf/hv-24x7: Update domain value check
+    - dccp: fix dccp_v4_err()/dccp_v6_err() again
+    - platform/x86: intel_scu_ipc: Check status after timeout in busy_loop()
+    - platform/x86: intel_scu_ipc: Check status upon timeout in
+      ipc_wait_for_interrupt()
+    - platform/x86: intel_scu_ipc: Don't override scu in
+      intel_scu_ipc_dev_simple_command()
+    - platform/x86: intel_scu_ipc: Fail IPC send if still busy
+    - x86/srso: Fix srso_show_state() side effect
+    - x86/srso: Fix SBPB enablement for spec_rstack_overflow=off
+    - net: hns3: fix GRE checksum offload issue
+    - net: hns3: only enable unicast promisc when mac table full
+    - net: hns3: fix fail to delete tc flower rules during reset issue
+    - net: hns3: add 5ms delay before clear firmware reset irq source
+    - net: bridge: use DEV_STATS_INC()
+    - team: fix null-ptr-deref when team device type is changed
+    - net: rds: Fix possible NULL-pointer dereference
+    - netfilter: nf_tables: disable toggling dormant table state more than once
+    - locking/seqlock: Do the lockdep annotation before locking in
+      do_write_seqcount_begin_nested()
+    - net: ena: Flush XDP packets on error.
+    - bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
+    - igc: Expose tx-usecs coalesce setting to user
+    - Fix up backport of 136191703038 ("interconnect: Teach lockdep about
+      icc_bw_lock order")
+    - gpio: tb10x: Fix an error handling path in tb10x_gpio_probe()
+    - i2c: mux: demux-pinctrl: check the return value of devm_kstrdup()
+    - i2c: mux: gpio: Replace custom acpi_get_local_address()
+    - i2c: mux: gpio: Add missing fwnode_handle_put()
+    - xfs: bound maximum wait time for inodegc work
+    - xfs: introduce xfs_inodegc_push()
+    - xfs: explicitly specify cpu when forcing inodegc delayed work to run
+      immediately
+    - xfs: check that per-cpu inodegc workers actually run on that cpu
+    - xfs: disable reaping in fscounters scrub
+    - xfs: fix xfs_inodegc_stop racing with mod_delayed_work
+    - Input: i8042 - rename i8042-x86ia64io.h to i8042-acpipnpio.h
+    - Input: i8042 - add quirk for TUXEDO Gemini 17 Gen1/Clevo PD70PN
+    - netfilter: exthdr: add support for tcp option removal
+    - netfilter: nft_exthdr: Fix non-linear header modification
+    - ata: libata: Rename link flag ATA_LFLAG_NO_DB_DELAY
+    - ata: ahci: Add support for AMD A85 FCH (Hudson D4)
+    - ata: ahci: Rename board_ahci_mobile
+    - ata: ahci: Add Elkhart Lake AHCI controller
+    - scsi: qla2xxx: Select qpair depending on which CPU post_cmd() gets called
+    - scsi: qla2xxx: Use raw_smp_processor_id() instead of smp_processor_id()
+    - btrfs: reset destination buffer when read_extent_buffer() gets invalid range
+    - MIPS: Alchemy: only build mmc support helpers if au1xmmc is enabled
+    - drm/bridge: ti-sn65dsi83: Do not generate HFP/HBP/HSA and EOT packet
+    - bus: ti-sysc: Use fsleep() instead of usleep_range() in sysc_reset()
+    - bus: ti-sysc: Fix missing AM35xx SoC matching
+    - clk: tegra: fix error return case for recalc_rate
+    - treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_56.RULE
+      (part 1)
+    - ARM: dts: omap: correct indentation
+    - ARM: dts: ti: omap: Fix bandgap thermal cells addressing for omap3/4
+    - ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot
+    - bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up
+    - power: supply: ucs1002: fix error code in ucs1002_get_property()
+    - firmware: imx-dsp: Fix an error handling path in imx_dsp_setup_channels()
+    - xtensa: add default definition for XCHAL_HAVE_DIV32
+    - xtensa: iss/network: make functions static
+    - xtensa: boot: don't add include-dirs
+    - xtensa: boot/lib: fix function prototypes
+    - soc: imx8m: Enable OCOTP clock for imx8mm before reading registers
+    - gpio: pmic-eic-sprd: Add can_sleep flag for PMIC EIC chip
+    - i2c: npcm7xx: Fix callback completion ordering
+    - dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock
+    - spi: sun6i: reduce DMA RX transfer width to single byte
+    - spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
+    - parisc: sba: Fix compile warning wrt list of SBA devices
+    - parisc: iosapic.c: Fix sparse warnings
+    - parisc: drivers: Fix sparse warning
+    - parisc: irq: Make irq_stack_union static to avoid sparse warning
+    - scsi: qedf: Add synchronization between I/O completions and abort
+    - scsi: ufs: core: Move __ufshcd_send_uic_cmd() outside host_lock
+    - selftests/ftrace: Correctly enable event in instance-event.tc
+    - ring-buffer: Avoid softlockup in ring_buffer_resize()
+    - btrfs: improve error message after failure to add delayed dir index item
+    - selftests: fix dependency checker script
+    - ring-buffer: Do not attempt to read past "commit"
+    - platform/mellanox: mlxbf-bootctl: add NET dependency into Kconfig
+    - drm/amd/display: Don't check registers, if using AUX BL control
+    - drm/amdgpu: Handle null atom context in VBIOS info ioctl
+    - scsi: pm80xx: Use phy-specific SAS address when sending PHY_START command
+    - scsi: pm80xx: Avoid leaking tags when processing
+      OPC_INB_SET_CONTROLLER_CONFIG command
+    - smb3: correct places where ENOTSUPP is used instead of preferred EOPNOTSUPP
+    - ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()
+    - spi: nxp-fspi: reset the FLSHxCR1 registers
+    - spi: stm32: add a delay before SPI disable
+    - ASoC: fsl: imx-pcm-rpmsg: Add SNDRV_PCM_INFO_BATCH flag
+    - bpf: Clarify error expectations from bpf_clone_redirect
+    - ASoC: imx-rpmsg: Set ignore_pmdown_time for dai_link
+    - media: vb2: frame_vector.c: replace WARN_ONCE with a comment
+    - powerpc/watchpoints: Disable preemption in thread_change_pc()
+    - powerpc/watchpoint: Disable pagefaults when getting user instruction
+    - powerpc/watchpoints: Annotate atomic context in more places
+    - ncsi: Propagate carrier gain/loss events to the NCSI controller
+    - fbdev/sh7760fb: Depend on FB=y
+    - perf build: Define YYNOMEM as YYNOABORT for bison < 3.81
+    - sched/cpuacct: Optimize away RCU read lock
+    - cgroup: Fix suspicious rcu_dereference_check() usage warning
+    - nvme-pci: factor the iod mempool creation into a helper
+    - nvme-pci: factor out a nvme_pci_alloc_dev helper
+    - nvme-pci: do not set the NUMA node of device if it has none
+    - watchdog: iTCO_wdt: No need to stop the timer in probe
+    - watchdog: iTCO_wdt: Set NO_REBOOT if the watchdog is not already running
+    - i40e: fix potential NULL pointer dereferencing of pf->vf
+      i40e_sync_vsi_filters()
+    - scsi: qla2xxx: Fix NULL pointer dereference in target mode
+    - nvme-pci: always return an ERR_PTR from nvme_pci_alloc_dev
+    - smack: Record transmuting in smk_transmuted
+    - smack: Retrieve transmuting information in smack_inode_getsecurity()
+    - Smack:- Use overlay inode label in smack_inode_copy_up()
+    - iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range
+    - x86/srso: Add SRSO mitigation for Hygon processors
+    - Revert "tty: n_gsm: fix UAF in gsm_cleanup_mux"
+    - serial: 8250_port: Check IRQ data before use
+    - nilfs2: fix potential use after free in nilfs_gccache_submit_read_data()
+    - ALSA: hda: Disable power save for solving pop issue on Lenovo ThinkCentre
+      M70q
+    - ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
+    - i2c: i801: unregister tco_pdev in i801_probe() error path
+    - sched/rt: Fix live lock between select_fallback_rq() and RT push
+    - io_uring/fs: remove sqe->rw_flags checking from LINKAT
+    - Revert "SUNRPC dont update timeout value on connection reset"
+    - proc: nommu: /proc/<pid>/maps: release mmap read lock
+    - ring-buffer: Update "shortest_full" in polling
+    - btrfs: properly report 0 avail for very full file systems
+    - bpf: Fix BTF_ID symbol generation collision
+    - bpf: Fix BTF_ID symbol generation collision in tools/
+    - net: thunderbolt: Fix TCPv6 GSO checksum calculation
+    - ata: libata-core: Fix ata_port_request_pm() locking
+    - ata: libata-core: Fix port and device removal
+    - ata: libata-core: Do not register PM operations for SAS ports
+    - ata: libata-sata: increase PMP SRST timeout to 10s
+    - fs: binfmt_elf_efpic: fix personality for ELF-FDPIC
+    - drm/meson: fix memory leak on ->hpd_notify callback
+    - Linux 5.15.134
+
+  * Jammy update: v5.15.133 upstream stable release (LP: #2043422)
+    - autofs: fix memory leak of waitqueues in autofs_catatonic_mode
+    - btrfs: output extra debug info if we failed to find an inline backref
+    - locks: fix KASAN: use-after-free in trace_event_raw_event_filelock_lock
+    - ACPICA: Add AML_NO_OPERAND_RESOLVE flag to Timer
+    - kernel/fork: beware of __put_task_struct() calling context
+    - rcuscale: Move rcu_scale_writer() schedule_timeout_uninterruptible() to
+      _idle()
+    - scftorture: Forgive memory-allocation failure if KASAN
+    - ACPI: video: Add backlight=native DMI quirk for Lenovo Ideapad Z470
+    - perf/smmuv3: Enable HiSilicon Erratum 162001900 quirk for HIP08/09
+    - perf/imx_ddr: speed up overflow frequency of cycle
+    - hw_breakpoint: fix single-stepping when using bpf_overflow_handler
+    - ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
+    - devlink: remove reload failed checks in params get/set callbacks
+    - crypto: lrw,xts - Replace strlcpy with strscpy
+    - wifi: ath9k: fix fortify warnings
+    - wifi: ath9k: fix printk specifier
+    - wifi: mwifiex: fix fortify warning
+    - wifi: wil6210: fix fortify warnings
+    - crypto: lib/mpi - avoid null pointer deref in mpi_cmp_ui()
+    - tpm_tis: Resend command to recover from data transfer errors
+    - mmc: sdhci-esdhc-imx: improve ESDHC_FLAG_ERR010450
+    - alx: fix OOB-read compiler warning
+    - wifi: mac80211: check S1G action frame size
+    - netfilter: ebtables: fix fortify warnings in size_entry_mwt()
+    - wifi: mac80211_hwsim: drop short frames
+    - drm/bridge: tc358762: Instruct DSI host to generate HSE packets
+    - arm64: dts: qcom: sm6125-pdx201: correct ramoops pmsg-size
+    - arm64: dts: qcom: sm8150-kumano: correct ramoops pmsg-size
+    - arm64: dts: qcom: sm8250-edo: correct ramoops pmsg-size
+    - samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'
+    - ALSA: hda: intel-dsp-cfg: add LunarLake support
+    - drm/amd/display: Blocking invalid 420 modes on HDMI TMDS for DCN31
+    - drm/exynos: fix a possible null-pointer dereference due to data race in
+      exynos_drm_crtc_atomic_disable()
+    - bus: ti-sysc: Configure uart quirks for k3 SoC
+    - md: raid1: fix potential OOB in raid1_remove_disk()
+    - ext2: fix datatype of block number in ext2_xattr_set2()
+    - fs/jfs: prevent double-free in dbUnmount() after failed jfs_remount()
+    - jfs: fix invalid free of JFS_IP(ipimap)->i_imap in diUnmount
+    - ARM: 9317/1: kexec: Make smp stop calls asynchronous
+    - powerpc/pseries: fix possible memory leak in ibmebus_bus_init()
+    - PCI: fu740: Set the number of MSI vectors
+    - media: dvb-usb-v2: af9035: Fix null-ptr-deref in af9035_i2c_master_xfer
+    - media: dw2102: Fix null-ptr-deref in dw2102_i2c_transfer()
+    - media: af9005: Fix null-ptr-deref in af9005_i2c_xfer
+    - media: anysee: fix null-ptr-deref in anysee_master_xfer
+    - media: az6007: Fix null-ptr-deref in az6007_i2c_xfer()
+    - media: dvb-usb-v2: gl861: Fix null-ptr-deref in gl861_i2c_master_xfer
+    - media: tuners: qt1010: replace BUG_ON with a regular error
+    - media: pci: cx23885: replace BUG with error return
+    - usb: cdns3: Put the cdns set active part outside the spin lock
+    - usb: gadget: fsl_qe_udc: validate endpoint index for ch9 udc
+    - tools: iio: iio_generic_buffer: Fix some integer type and calculation
+    - scsi: target: iscsi: Fix buffer overflow in lio_target_nacl_info_show()
+    - serial: cpm_uart: Avoid suspicious locking
+    - usb: ehci: add workaround for chipidea PORTSC.PEC bug
+    - media: pci: ipu3-cio2: Initialise timing struct to avoid a compiler warning
+    - kobject: Add sanity check for kset->kobj.ktype in kset_register()
+    - interconnect: Fix locking for runpm vs reclaim
+    - printk: Consolidate console deferred printing
+    - jbd2: refactor wait logic for transaction updates into a common function
+    - jbd2: fix use-after-free of transaction_t race
+    - jbd2: kill t_handle_lock transaction spinlock
+    - jbd2: rename jbd_debug() to jbd2_debug()
+    - jbd2: correct the end of the journal recovery scan range
+    - mtd: rawnand: brcmnand: Allow SoC to provide I/O operations
+    - mtd: rawnand: brcmnand: Fix ECC level field setting for v7.2 controller
+    - MIPS: Use "grep -E" instead of "egrep"
+    - perf test: Remove bash construct from stat_bpf_counters.sh test
+    - perf test shell stat_bpf_counters: Fix test on Intel
+    - btrfs: move btrfs_pinned_by_swapfile prototype into volumes.h
+    - btrfs: add a helper to read the superblock metadata_uuid
+    - btrfs: compare the correct fsid/metadata_uuid in btrfs_validate_super
+    - drm: gm12u320: Fix the timeout usage for usb_bulk_msg()
+    - scsi: qla2xxx: Fix NULL vs IS_ERR() bug for debugfs_create_dir()
+    - selftests: tracing: Fix to unmount tracefs for recovering environment
+    - scsi: lpfc: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
+    - x86/boot/compressed: Reserve more memory for page tables
+    - x86/purgatory: Remove LTO flags
+    - samples/hw_breakpoint: fix building without module unloading
+    - md/raid1: fix error: ISO C90 forbids mixed declarations
+    - attr: block mode changes of symlinks
+    - ovl: fix failed copyup of fileattr on a symlink
+    - ovl: fix incorrect fdput() on aio completion
+    - btrfs: fix lockdep splat and potential deadlock after failure running
+      delayed items
+    - btrfs: release path before inode lookup during the ino lookup ioctl
+    - tracing: Have tracing_max_latency inc the trace array ref count
+    - tracing: Have current_trace inc the trace array ref count
+    - tracing: Have option files inc the trace array ref count
+    - nfsd: fix change_info in NFSv4 RENAME replies
+    - tracefs: Add missing lockdown check to tracefs_create_dir()
+    - i2c: aspeed: Reset the i2c controller when timeout occurs
+    - ata: libata: disallow dev-initiated LPM transitions to unsupported states
+    - scsi: megaraid_sas: Fix deadlock on firmware crashdump
+    - scsi: pm8001: Setup IRQs on resume
+    - ext4: fix rec_len verify error
+    - drm/amd/display: fix the white screen issue when >= 64GB DRAM
+    - drm/amdgpu: fix amdgpu_cs_p1_user_fence
+    - drm/amd/display: enable cursor degamma for DCN3+ DRM legacy gamma
+    - interconnect: Teach lockdep about icc_bw_lock order
+    - Linux 5.15.133
+
+  * Jammy update: v5.15.132 upstream stable release (LP: #2041702)
+    - ARM: dts: imx: update sdma node name format
+    - ARM: dts: imx7s: Drop dma-apb interrupt-names
+    - ARM: dts: imx: Adjust dma-apbh node name
+    - ARM: dts: imx: Set default tuning step for imx7d usdhc
+    - phy: qcom-snps-femto-v2: use qcom_snps_hsphy_suspend/resume error code
+    - media: pulse8-cec: handle possible ping error
+    - media: pci: cx23885: fix error handling for cx23885 ATSC boards
+    - 9p: virtio: make sure 'offs' is initialized in zc_request
+    - ksmbd: fix out of bounds in smb3_decrypt_req()
+    - ksmbd: no response from compound read
+    - ASoC: da7219: Flush pending AAD IRQ when suspending
+    - ASoC: da7219: Check for failure reading AAD IRQ events
+    - ethernet: atheros: fix return value check in atl1c_tso_csum()
+    - vxlan: generalize vxlan_parse_gpe_hdr and remove unused args
+    - m68k: Fix invalid .section syntax
+    - s390/dasd: use correct number of retries for ERP requests
+    - s390/dasd: fix hanging device after request requeue
+    - fs/nls: make load_nls() take a const parameter
+    - ASoC: rt5682-sdw: fix for JD event handling in ClockStop Mode0
+    - ASoc: codecs: ES8316: Fix DMIC config
+    - ASoC: rt711: fix for JD event handling in ClockStop Mode0
+    - ASoC: rt711-sdca: fix for JD event handling in ClockStop Mode0
+    - ASoC: atmel: Fix the 8K sample parameter in I2SC master
+    - platform/x86: intel: hid: Always call BTNL ACPI method
+    - platform/x86/intel/hid: Add HP Dragonfly G2 to VGBS DMI quirks
+    - platform/x86: huawei-wmi: Silence ambient light sensor
+    - drm/amd/display: Exit idle optimizations before attempt to access PHY
+    - ovl: Always reevaluate the file signature for IMA
+    - ata: pata_arasan_cf: Use dev_err_probe() instead dev_err() in data_xfer()
+    - security: keys: perform capable check only on privileged operations
+    - kprobes: Prohibit probing on CFI preamble symbol
+    - clk: fixed-mmio: make COMMON_CLK_FIXED_MMIO depend on HAS_IOMEM
+    - vmbus_testing: fix wrong python syntax for integer value comparison
+    - net: usb: qmi_wwan: add Quectel EM05GV2
+    - wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
+    - idmaengine: make FSL_EDMA and INTEL_IDMA64 depends on HAS_IOMEM
+    - scsi: lpfc: Remove reftag check in DIF paths
+    - scsi: qedi: Fix potential deadlock on &qedi_percpu->p_work_lock
+    - net: hns3: restore user pause configure when disable autoneg
+    - drm/amdgpu: Match against exact bootloader status
+    - netlabel: fix shift wrapping bug in netlbl_catmap_setlong()
+    - bnx2x: fix page fault following EEH recovery
+    - sctp: handle invalid error codes without calling BUG()
+    - scsi: storvsc: Always set no_report_opcodes
+    - scsi: lpfc: Fix incorrect big endian type assignment in bsg loopback path
+    - ALSA: seq: oss: Fix racy open/close of MIDI devices
+    - tracing: Introduce pipe_cpumask to avoid race on trace_pipes
+    - platform/mellanox: Fix mlxbf-tmfifo not handling all virtio CONSOLE
+      notifications
+    - arm64: lib: Import latest version of Arm Optimized Routines' strncmp
+    - of: kexec: Mark ima_{free,stable}_kexec_buffer() as __init
+    - udf: Check consistency of Space Bitmap Descriptor
+    - udf: Handle error when adding extent to a file
+    - Revert "net: macsec: preserve ingress frame ordering"
+    - reiserfs: Check the return value from __getblk()
+    - eventfd: prevent underflow for eventfd semaphores
+    - fs: Fix error checking for d_hash_and_lookup()
+    - tmpfs: verify {g,u}id mount options correctly
+    - selftests/harness: Actually report SKIP for signal tests
+    - ARM: ptrace: Restore syscall restart tracing
+    - ARM: ptrace: Restore syscall skipping for tracers
+    - refscale: Fix uninitalized use of wait_queue_head_t
+    - OPP: Fix passing 0 to PTR_ERR in _opp_attach_genpd()
+    - selftests/resctrl: Make resctrl_tests run using kselftest framework
+    - selftests/resctrl: Add resctrl.h into build deps
+    - selftests/resctrl: Don't leak buffer in fill_cache()
+    - selftests/resctrl: Unmount resctrl FS if child fails to run benchmark
+    - selftests/resctrl: Close perf value read fd on errors
+    - x86/decompressor: Don't rely on upper 32 bits of GPRs being preserved
+    - perf/imx_ddr: don't enable counter0 if none of 4 counters are used
+    - selftests/futex: Order calls to futex_lock_pi
+    - s390/pkey: fix/harmonize internal keyblob headers
+    - s390/paes: fix PKEY_TYPE_EP11_AES handling for secure keyblobs
+    - ACPI: x86: s2idle: Post-increment variables when getting constraints
+    - ACPI: x86: s2idle: Fix a logic error parsing AMD constraints table
+    - x86/efistub: Fix PCI ROM preservation in mixed mode
+    - cpufreq: powernow-k8: Use related_cpus instead of cpus in driver.exit()
+    - bpftool: Use a local bpf_perf_event_value to fix accessing its fields
+    - bpf: Clear the probe_addr for uprobe
+    - tcp: tcp_enter_quickack_mode() should be static
+    - hwrng: nomadik - keep clock enabled while hwrng is registered
+    - hwrng: pic32 - use devm_clk_get_enabled
+    - regmap: rbtree: Use alloc_flags for memory allocations
+    - udp: re-score reuseport groups when connected sockets are present
+    - bpf: reject unhashed sockets in bpf_sk_assign
+    - ipv6: Add reasons for skb drops to __udp6_lib_rcv
+    - wifi: mt76: testmode: add nla_policy for MT76_TM_ATTR_TX_LENGTH
+    - spi: tegra20-sflash: fix to check return value of platform_get_irq() in
+      tegra_sflash_probe()
+    - can: gs_usb: gs_usb_receive_bulk_callback(): count RX overflow errors also
+      in case of OOM
+    - wifi: mt76: mt7915: fix power-limits while chan_switch
+    - wifi: mwifiex: Fix OOB and integer underflow when rx packets
+    - wifi: mwifiex: fix error recovery in PCIE buffer descriptor management
+    - crypto: stm32 - Properly handle pm_runtime_get failing
+    - crypto: api - Use work queue in crypto_destroy_instance
+    - Bluetooth: nokia: fix value check in nokia_bluetooth_serdev_probe()
+    - Bluetooth: Fix potential use-after-free when clear keys
+    - net: tcp: fix unexcepted socket die when snd_wnd is 0
+    - selftests/bpf: Clean up fmod_ret in bench_rename test script
+    - net-memcg: Fix scope of sockmem pressure indicators
+    - ice: ice_aq_check_events: fix off-by-one check when filling buffer
+    - crypto: caam - fix unchecked return value error
+    - hwrng: iproc-rng200 - Implement suspend and resume calls
+    - lwt: Fix return values of BPF xmit ops
+    - lwt: Check LWTUNNEL_XMIT_CONTINUE strictly
+    - fs: ocfs2: namei: check return value of ocfs2_add_entry()
+    - wifi: mwifiex: fix memory leak in mwifiex_histogram_read()
+    - wifi: mwifiex: Fix missed return in oob checks failed path
+    - samples/bpf: fix broken map lookup probe
+    - wifi: ath9k: fix races between ath9k_wmi_cmd and ath9k_wmi_ctrl_rx
+    - wifi: ath9k: protect WMI command response buffer replacement with a lock
+    - wifi: nl80211/cfg80211: add forgotten nla_policy for BSS color attribute
+    - wifi: mwifiex: avoid possible NULL skb pointer dereference
+    - Bluetooth: btusb: Do not call kfree_skb() under spin_lock_irqsave()
+    - wifi: ath9k: use IS_ERR() with debugfs_create_dir()
+    - net: arcnet: Do not call kfree_skb() under local_irq_disable()
+    - mlxsw: i2c: Fix chunk size setting in output mailbox buffer
+    - mlxsw: i2c: Limit single transaction buffer size
+    - hwmon: (tmp513) Fix the channel number in tmp51x_is_visible()
+    - netrom: Deny concurrent connect().
+    - drm/bridge: tc358764: Fix debug print parameter order
+    - quota: factor out dquot_write_dquot()
+    - quota: rename dquot_active() to inode_quota_active()
+    - quota: add new helper dquot_active()
+    - quota: fix dqput() to follow the guarantees dquot_srcu should provide
+    - ASoC: stac9766: fix build errors with REGMAP_AC97
+    - soc: qcom: ocmem: Add OCMEM hardware version print
+    - soc: qcom: ocmem: Fix NUM_PORTS & NUM_MACROS macros
+    - arm64: dts: qcom: sm8250: correct dynamic power coefficients
+    - arm64: dts: qcom: sm8250-edo: Add gpio line names for TLMM
+    - arm64: dts: qcom: sm8250-edo: Add GPIO line names for PMIC GPIOs
+    - arm64: dts: qcom: sm8250-edo: Rectify gpio-keys
+    - arm64: dts: qcom: msm8996: Add missing interrupt to the USB2 controller
+    - arm64: dts: qcom: sm8350: Add missing LMH interrupts to cpufreq
+    - arm64: dts: qcom: sm8350: Use proper CPU compatibles
+    - arm64: dts: qcom: pmk8350: fix ADC-TM compatible string
+    - arm64: dts: qcom: sm8250: Mark PCIe hosts as DMA coherent
+    - drm/amdgpu: avoid integer overflow warning in amdgpu_device_resize_fb_bar()
+    - ARM: dts: BCM53573: Add cells sizes to PCIe node
+    - ARM: dts: BCM53573: Use updated "spi-gpio" binding properties
+    - arm64: dts: qcom: sm8250-sony-xperia: correct GPIO keys wakeup again
+    - arm64: dts: qcom: pmi8998: Add node for WLED
+    - arm64: dts: qcom: correct SPMI WLED register range encoding
+    - arm64: dts: qcom: pm660l: Add missing short interrupt
+    - arm64: dts: qcom: pmi8994: Remove hardcoded linear WLED enabled-strings
+    - arm64: dts: qcom: Move WLED num-strings from pmi8994 to sony-xperia-tone
+    - arm64: dts: qcom: pmi8994: Add missing OVP interrupt
+    - drm/etnaviv: fix dumping of active MMU context
+    - x86/mm: Fix PAT bit missing from page protection modify mask
+    - ARM: dts: s3c64xx: align pinctrl with dtschema
+    - ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)
+    - ARM: dts: s5pv210: add dummy 5V regulator for backlight on SMDKv210
+    - ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)
+    - drm: adv7511: Fix low refresh rate register for ADV7533/5
+    - ARM: dts: BCM53573: Fix Ethernet info for Luxul devices
+    - arm64: dts: qcom: sdm845: Add missing RPMh power domain to GCC
+    - arm64: dts: qcom: sdm845: Fix the min frequency of "ice_core_clk"
+    - drm/amdgpu: Update min() to min_t() in 'amdgpu_info_ioctl'
+    - md/raid10: factor out dereference_rdev_and_rrdev()
+    - md/raid10: use dereference_rdev_and_rrdev() to get devices
+    - md/bitmap: don't set max_write_behind if there is no write mostly device
+    - md/md-bitmap: hold 'reconfig_mutex' in backlog_store()
+    - drm/msm: Update dev core dump to not print backwards
+    - drm/tegra: dpaux: Fix incorrect return value of platform_get_irq
+    - of: unittest: fix null pointer dereferencing in
+      of_unittest_find_node_by_name()
+    - arm64: dts: qcom: sm8150: Fix the I2C7 interrupt
+    - drm/armada: Fix off-by-one error in armada_overlay_get_property()
+    - drm/panel: simple: Add missing connector type and pixel format for AUO
+      T215HVN01
+    - ima: Remove deprecated IMA_TRUSTED_KEYRING Kconfig
+    - [Config] updateconfigs for IMA_TRUSTED_KEYRING
+    - drm: xlnx: zynqmp_dpsub: Add missing check for dma_set_mask
+    - drm/msm/mdp5: Don't leak some plane state
+    - firmware: meson_sm: fix to avoid potential NULL pointer dereference
+    - smackfs: Prevent underflow in smk_set_cipso()
+    - drm/amd/pm: fix variable dereferenced issue in amdgpu_device_attr_create()
+    - drm/msm/a2xx: Call adreno_gpu_init() earlier
+    - audit: fix possible soft lockup in __audit_inode_child()
+    - io_uring: fix drain stalls by invalid SQE
+    - bus: ti-sysc: Fix build warning for 64-bit build
+    - drm/mediatek: Remove freeing not dynamic allocated memory
+    - drm/mediatek: Fix potential memory leak if vmap() fail
+    - arm64: dts: qcom: apq8016-sbc: Fix ov5640 regulator supply names
+    - bus: ti-sysc: Fix cast to enum warning
+    - md: Set MD_BROKEN for RAID1 and RAID10
+    - md: add error_handlers for raid0 and linear
+    - md/raid0: Factor out helper for mapping and submitting a bio
+    - md/raid0: Fix performance regression for large sequential writes
+    - md: raid0: account for split bio in iostat accounting
+    - of: overlay: Call of_changeset_init() early
+    - of: unittest: Fix overlay type in apply/revert check
+    - ALSA: ac97: Fix possible error value of *rac97
+    - ipmi:ssif: Add check for kstrdup
+    - ipmi:ssif: Fix a memory leak when scanning for an adapter
+    - drivers: clk: keystone: Fix parameter judgment in _of_pll_clk_init()
+    - clk: sunxi-ng: Modify mismatched function name
+    - clk: qcom: gcc-sc7180: Fix up gcc_sdcc2_apps_clk_src
+    - EDAC/igen6: Fix the issue of no error events
+    - ext4: correct grp validation in ext4_mb_good_group
+    - ext4: avoid potential data overflow in next_linear_group
+    - clk: qcom: gcc-sm8250: Fix gcc_sdcc2_apps_clk_src
+    - clk: qcom: reset: Use the correct type of sleep/delay based on length
+    - clk: qcom: gcc-sm6350: Fix gcc_sdcc2_apps_clk_src
+    - PCI: microchip: Correct the DED and SEC interrupt bit offsets
+    - PCI: Mark NVIDIA T4 GPUs to avoid bus reset
+    - pinctrl: mcp23s08: check return value of devm_kasprintf()
+    - PCI: pciehp: Use RMW accessors for changing LNKCTL
+    - PCI/ASPM: Use RMW accessors for changing LNKCTL
+    - clk: imx8mp: fix sai4 clock
+    - clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
+    - powerpc/radix: Move some functions into #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
+    - vfio/type1: fix cap_migration information leak
+    - powerpc/fadump: reset dump area size if fadump memory reserve fails
+    - powerpc/perf: Convert fsl_emb notifier to state machine callbacks
+    - drm/amdgpu: Use RMW accessors for changing LNKCTL
+    - drm/radeon: Use RMW accessors for changing LNKCTL
+    - net/mlx5: Use RMW accessors for changing LNKCTL
+    - wifi: ath11k: Use RMW accessors for changing LNKCTL
+    - wifi: ath10k: Use RMW accessors for changing LNKCTL
+    - PCI: dwc: Add start_link/stop_link inlines
+    - PCI: layerscape: Add the endpoint linkup notifier support
+    - PCI: layerscape: Add workaround for lost link capabilities during reset
+    - powerpc: Don't include lppaca.h in paca.h
+    - powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
+    - nfs/blocklayout: Use the passed in gfp flags
+    - powerpc/iommu: Fix notifiers being shared by PCI and VIO buses
+    - ext4: fix unttached inode after power cut with orphan file feature enabled
+    - jfs: validate max amount of blocks before allocation.
+    - fs: lockd: avoid possible wrong NULL parameter
+    - NFSD: da_addr_body field missing in some GETDEVICEINFO replies
+    - NFS: Guard against READDIR loop when entry names exceed MAXNAMELEN
+    - NFSv4.2: fix handling of COPY ERR_OFFLOAD_NO_REQ
+    - pNFS: Fix assignment of xprtdata.cred
+    - RDMA/qedr: Remove a duplicate assignment in irdma_query_ah()
+    - media: ad5820: Drop unsupported ad5823 from i2c_ and of_device_id tables
+    - media: i2c: tvp5150: check return value of devm_kasprintf()
+    - media: v4l2-core: Fix a potential resource leak in v4l2_fwnode_parse_link()
+    - iommu/amd/iommu_v2: Fix pasid_state refcount dec hit 0 warning on pasid
+      unbind
+    - iommu: rockchip: Fix directory table address encoding
+    - drivers: usb: smsusb: fix error handling code in smsusb_init_device
+    - media: dib7000p: Fix potential division by zero
+    - media: dvb-usb: m920x: Fix a potential memory leak in m920x_i2c_xfer()
+    - media: cx24120: Add retval check for cx24120_message_send()
+    - scsi: hisi_sas: Modify v3 HW SSP underflow error processing
+    - scsi: hisi_sas: Modify v3 HW SATA completion error processing
+    - scsi: hisi_sas: Fix warnings detected by sparse
+    - scsi: hisi_sas: Fix normally completed I/O analysed as failed
+    - media: rkvdec: increase max supported height for H.264
+    - media: mediatek: vcodec: Return NULL if no vdec_fb is found
+    - usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()
+    - scsi: RDMA/srp: Fix residual handling
+    - scsi: iscsi: Rename iscsi_set_param() to iscsi_if_set_param()
+    - scsi: iscsi: Add length check for nlattr payload
+    - scsi: iscsi: Add strlen() check in iscsi_if_set{_host}_param()
+    - scsi: be2iscsi: Add length check when parsing nlattrs
+    - scsi: qla4xxx: Add length check when parsing nlattrs
+    - serial: sprd: Assign sprd_port after initialized to avoid wrong access
+    - serial: sprd: Fix DMA buffer leak issue
+    - x86/APM: drop the duplicate APM_MINOR_DEV macro
+    - scsi: qedf: Do not touch __user pointer in
+      qedf_dbg_stop_io_on_error_cmd_read() directly
+    - scsi: qedf: Do not touch __user pointer in qedf_dbg_debug_cmd_read()
+      directly
+    - scsi: qedf: Do not touch __user pointer in qedf_dbg_fp_int_cmd_read()
+      directly
+    - RDMA/irdma: Replace one-element array with flexible-array member
+    - coresight: tmc: Explicit type conversions to prevent integer overflow
+    - dma-buf/sync_file: Fix docs syntax
+    - driver core: test_async: fix an error code
+    - iommu/sprd: Add missing force_aperture
+    - RDMA/hns: Fix port active speed
+    - RDMA/hns: Fix incorrect post-send with direct wqe of wr-list
+    - RDMA/hns: Fix CQ and QP cache affinity
+    - IB/uverbs: Fix an potential error pointer dereference
+    - fsi: aspeed: Reset master errors after CFAM reset
+    - iommu/qcom: Disable and reset context bank before programming
+    - iommu/vt-d: Fix to flush cache of PASID directory table
+    - platform/x86: dell-sysman: Fix reference leak
+    - media: go7007: Remove redundant if statement
+    - media: venus: hfi_venus: Only consider sys_idle_indicator on V1
+    - USB: gadget: f_mass_storage: Fix unused variable warning
+    - media: ov5640: Enable MIPI interface in ov5640_set_power_mipi()
+    - media: i2c: ov2680: Set V4L2_CTRL_FLAG_MODIFY_LAYOUT on flips
+    - media: ov2680: Remove auto-gain and auto-exposure controls
+    - media: ov2680: Fix ov2680_bayer_order()
+    - media: ov2680: Fix vflip / hflip set functions
+    - media: ov2680: Remove VIDEO_V4L2_SUBDEV_API ifdef-s
+    - media: ov2680: Don't take the lock for try_fmt calls
+    - media: ov2680: Add ov2680_fill_format() helper function
+    - media: ov2680: Fix ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY not
+      working
+    - media: ov2680: Fix regulators being left enabled on ov2680_power_on() errors
+    - media: i2c: rdacm21: Fix uninitialized value
+    - cgroup:namespace: Remove unused cgroup_namespaces_init()
+    - scsi: core: Use 32-bit hostnum in scsi_host_lookup()
+    - scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock
+    - serial: tegra: handle clk prepare error in tegra_uart_hw_init()
+    - amba: bus: fix refcount leak
+    - Revert "IB/isert: Fix incorrect release of isert connection"
+    - HID: logitech-dj: Fix error handling in logi_dj_recv_switch_to_dj_mode()
+    - HID: multitouch: Correct devm device reference for hidinput input_dev name
+    - x86/speculation: Mark all Skylake CPUs as vulnerable to GDS
+    - tracing: Remove extra space at the end of hwlat_detector/mode
+    - tracing: Fix race issue between cpu buffer write and swap
+    - mtd: rawnand: brcmnand: Fix mtd oobsize
+    - phy/rockchip: inno-hdmi: use correct vco_div_5 macro on rk3328
+    - phy/rockchip: inno-hdmi: round fractal pixclock in rk3328 recalc_rate
+    - phy/rockchip: inno-hdmi: do not power on rk3328 post pll on reg write
+    - rpmsg: glink: Add check for kstrdup
+    - leds: pwm: Fix error code in led_pwm_create_fwnode()
+    - leds: multicolor: Use rounded division when calculating color components
+    - leds: trigger: tty: Do not use LED_ON/OFF constants, use
+      led_blink_set_oneshot instead
+    - mtd: spi-nor: Check bus width while setting QE bit
+    - mtd: rawnand: fsmc: handle clk prepare error in fsmc_nand_resume()
+    - um: Fix hostaudio build errors
+    - dmaengine: ste_dma40: Add missing IRQ check in d40_probe
+    - cpufreq: Fix the race condition while updating the transition_task of policy
+    - virtio_ring: fix avail_wrap_counter in virtqueue_add_packed
+    - skbuff: skb_segment, Call zero copy functions before using skbuff frags
+    - PM / devfreq: Fix leak in devfreq_dev_release()
+    - ALSA: pcm: Fix missing fixup call in compat hw_refine ioctl
+    - rcu: dump vmalloc memory info safely
+    - printk: ringbuffer: Fix truncating buffer size min_t cast
+    - scsi: core: Fix the scsi_set_resid() documentation
+    - mm/vmalloc: add a safer version of find_vm_area() for debug
+    - media: i2c: ccs: Check rules is non-NULL
+    - PCI: rockchip: Use 64-bit mask on MSI 64-bit PCI address
+    - ipmi_si: fix a memleak in try_smi_init()
+    - ARM: OMAP2+: Fix -Warray-bounds warning in _pwrdm_state_switch()
+    - backlight/gpio_backlight: Compare against struct fb_info.device
+    - backlight/bd6107: Compare against struct fb_info.device
+    - backlight/lv5207lp: Compare against struct fb_info.device
+    - xtensa: PMU: fix base address for the newer hardware
+    - i3c: master: svc: fix probe failure when no i3c device exist
+    - arm64: csum: Fix OoB access in IP checksum code for negative lengths
+    - media: dvb: symbol fixup for dvb_attach()
+    - media: venus: hfi_venus: Write to VIDC_CTRL_INIT after unmasking interrupts
+    - Revert "scsi: qla2xxx: Fix buffer overrun"
+    - scsi: mpt3sas: Perform additional retries if doorbell read returns 0
+    - ntb: Drop packets when qp link is down
+    - ntb: Clean up tx tail index on link down
+    - ntb: Fix calculation ntb_transport_tx_free_entry()
+    - Revert "PCI: Mark NVIDIA T4 GPUs to avoid bus reset"
+    - procfs: block chmod on /proc/thread-self/comm
+    - parisc: Fix /proc/cpuinfo output for lscpu
+    - dlm: fix plock lookup when using multiple lockspaces
+    - dccp: Fix out of bounds access in DCCP error handler
+    - X.509: if signature is unsupported skip validation
+    - net: handle ARPHRD_PPP in dev_is_mac_header_xmit()
+    - fsverity: skip PKCS#7 parser when keyring is empty
+    - mmc: renesas_sdhi: register irqs before registering controller
+    - pstore/ram: Check start of empty przs during init
+    - arm64: sdei: abort running SDEI handlers during crash
+    - s390/ipl: add missing secure/has_secure file to ipl type 'unknown'
+    - crypto: stm32 - fix loop iterating through scatterlist for DMA
+    - cpufreq: brcmstb-avs-cpufreq: Fix -Warray-bounds bug
+    - usb: typec: tcpm: set initial svdm version based on pd revision
+    - usb: typec: bus: verify partner exists in typec_altmode_attention
+    - x86/sgx: Break up long non-preemptible delays in sgx_vepc_release()
+    - perf/x86/uncore: Correct the number of CHAs on EMR
+    - tracing: Zero the pipe cpumask on alloc to avoid spurious -EBUSY
+    - md/md-bitmap: remove unnecessary local variable in backlog_store()
+    - udf: initialize newblock to 0
+    - net/ipv6: SKB symmetric hash should incorporate transport ports
+    - io_uring: always lock in io_apoll_task_func
+    - io_uring: break out of iowq iopoll on teardown
+    - io_uring: break iopolling on signal
+    - scsi: qla2xxx: Adjust IOCB resource on qpair create
+    - scsi: qla2xxx: Limit TMF to 8 per function
+    - scsi: qla2xxx: Fix deletion race condition
+    - scsi: qla2xxx: fix inconsistent TMF timeout
+    - scsi: qla2xxx: Fix command flush during TMF
+    - scsi: qla2xxx: Fix erroneous link up failure
+    - scsi: qla2xxx: Turn off noisy message log
+    - scsi: qla2xxx: Fix session hang in gnl
+    - scsi: qla2xxx: Fix TMF leak through
+    - scsi: qla2xxx: Remove unsupported ql2xenabledif option
+    - scsi: qla2xxx: Flush mailbox commands on chip reset
+    - scsi: qla2xxx: Fix smatch warn for qla_init_iocb_limit()
+    - scsi: qla2xxx: Error code did not return to upper layer
+    - scsi: qla2xxx: Fix firmware resource tracking
+    - fbdev/ep93xx-fb: Do not assign to struct fb_info.dev
+    - clk: qcom: camcc-sc7180: fix async resume during probe
+    - drm/ast: Fix DRAM init on AST2200
+    - clk: qcom: turingcc-qcs404: fix missing resume during probe
+    - lib/test_meminit: allocate pages up to order MAX_ORDER
+    - parisc: led: Fix LAN receive and transmit LEDs
+    - parisc: led: Reduce CPU overhead for disk & lan LED computation
+    - pinctrl: cherryview: fix address_space_handler() argument
+    - dt-bindings: clock: xlnx,versal-clk: drop select:false
+    - clk: qcom: gcc-mdm9615: use proper parent for pll0_vote clock
+    - soc: qcom: qmi_encdec: Restrict string length in decode
+    - clk: qcom: q6sstop-qcs404: fix missing resume during probe
+    - clk: qcom: mss-sc7180: fix missing resume during probe
+    - NFS: Fix a potential data corruption
+    - NFSv4/pnfs: minor fix for cleanup path in nfs4_get_device_info
+    - bus: mhi: host: Skip MHI reset if device is in RDDM
+    - kbuild: do not run depmod for 'make modules_sign'
+    - gfs2: Switch to wait_event in gfs2_logd
+    - gfs2: low-memory forced flush fixes
+    - kconfig: fix possible buffer overflow
+    - perf trace: Use zfree() to reduce chances of use after free
+    - perf trace: Really free the evsel->priv area
+    - pwm: atmel-tcb: Convert to platform remove callback returning void
+    - pwm: atmel-tcb: Harmonize resource allocation order
+    - pwm: atmel-tcb: Fix resource freeing in error path and remove
+    - backlight: gpio_backlight: Drop output GPIO direction check for initial
+      power state
+    - Input: tca6416-keypad - always expect proper IRQ number in i2c client
+    - Input: tca6416-keypad - fix interrupt enable disbalance
+    - perf annotate bpf: Don't enclose non-debug code with an assert()
+    - x86/virt: Drop unnecessary check on extended CPUID level in cpu_has_svm()
+    - perf vendor events: Update the JSON/events descriptions for power10 platform
+    - perf vendor events: Drop some of the JSON/events for power10 platform
+    - perf top: Don't pass an ERR_PTR() directly to perf_session__delete()
+    - watchdog: intel-mid_wdt: add MODULE_ALIAS() to allow auto-load
+    - pwm: lpc32xx: Remove handling of PWM channels
+    - net/sched: fq_pie: avoid stalls in fq_pie_timer()
+    - sctp: annotate data-races around sk->sk_wmem_queued
+    - ipv4: annotate data-races around fi->fib_dead
+    - net: read sk->sk_family once in sk_mc_loop()
+    - net: fib: avoid warn splat in flow dissector
+    - xsk: Fix xsk_diag use-after-free error during socket cleanup
+    - drm/i915/gvt: Drop unused helper intel_vgpu_reset_gtt()
+    - ipv4: ignore dst hint for multipath routes
+    - igb: disable virtualization features on 82580
+    - veth: Fixing transmit return status for dropped packets
+    - net: ipv6/addrconf: avoid integer underflow in ipv6_create_tempaddr
+    - net: phy: micrel: Correct bit assignments for phy_device flags
+    - af_unix: Fix data-races around user->unix_inflight.
+    - af_unix: Fix data-race around unix_tot_inflight.
+    - af_unix: Fix data-races around sk->sk_shutdown.
+    - af_unix: Fix data race around sk->sk_err.
+    - kcm: Destroy mutex in kcm_exit_net()
+    - octeontx2-af: Fix truncation of smq in CN10K NIX AQ enqueue mbox handler
+    - igc: Change IGC_MIN to allow set rx/tx value between 64 and 80
+    - igbvf: Change IGBVF_MIN to allow set rx/tx value between 64 and 80
+    - igb: Change IGB_MIN to allow set rx/tx value between 64 and 80
+    - s390/zcrypt: don't leak memory if dev_set_name() fails
+    - idr: fix param name in idr_alloc_cyclic() doc
+    - ip_tunnels: use DEV_STATS_INC()
+    - net: dsa: sja1105: fix bandwidth discrepancy between tc-cbs software and
+      offload
+    - net: dsa: sja1105: fix -ENOSPC when replacing the same tc-cbs too many times
+    - net: dsa: sja1105: complete tc-cbs offload support on SJA1110
+    - net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
+    - net: hns3: fix debugfs concurrency issue between kfree buffer and read
+    - net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
+    - net: hns3: fix the port information display when sfp is absent
+    - net: hns3: remove GSO partial feature bit
+    - sh: boards: Fix CEU buffer size passed to dma_declare_coherent_memory()
+    - net/mlx5: Free IRQ rmap and notifier on kernel shutdown
+    - ARC: atomics: Add compiler barrier to atomic operations...
+    - dmaengine: sh: rz-dmac: Fix destination and source data size setting
+    - jbd2: fix checkpoint cleanup performance regression
+    - jbd2: check 'jh->b_transaction' before removing it from checkpoint
+    - ext4: add correct group descriptors and reserved GDT blocks to system zone
+    - lib: test_scanf: Add explicit type cast to result initialization in
+      test_number_prefix()
+    - ata: pata_falcon: fix IO base selection for Q40
+    - ata: sata_gemini: Add missing MODULE_DESCRIPTION
+    - ata: pata_ftide010: Add missing MODULE_DESCRIPTION
+    - fuse: nlookup missing decrement in fuse_direntplus_link
+    - btrfs: free qgroup rsv on io failure
+    - btrfs: don't start transaction when joining with TRANS_JOIN_NOSTART
+    - btrfs: use the correct superblock to compare fsid in btrfs_validate_super
+    - mtd: rawnand: brcmnand: Fix crash during the panic_write
+    - mtd: rawnand: brcmnand: Fix potential out-of-bounds access in oob write
+    - mtd: rawnand: brcmnand: Fix potential false time out warning
+    - drm/amd/display: prevent potential division by zero errors
+    - MIPS: Fix CONFIG_CPU_DADDI_WORKAROUNDS `modules_install' regression
+    - perf hists browser: Fix hierarchy mode header
+    - perf tools: Handle old data in PERF_RECORD_ATTR
+    - perf hists browser: Fix the number of entries for 'e' key
+    - pcd: move the identify buffer into pcd_identify
+    - pcd: cleanup initialization
+    - block: move GENHD_FL_NATIVE_CAPACITY to disk->state
+    - block: move GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE to disk->event_flags
+    - block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART
+    - block: don't add or resize partition on the disk with GENHD_FL_NO_PART
+    - ARM: dts: samsung: exynos4210-i9100: Fix LCD screen's physical size
+    - ARM: dts: BCM5301X: Extend RAM to full 256MB for Linksys EA6500 V2
+    - net: ipv4: fix one memleak in __inet_del_ifa()
+    - kselftest/runner.sh: Propagate SIGTERM to runner child
+    - net/smc: use smc_lgr_list.lock to protect smc_lgr_list.list iterate in
+      smcr_port_add
+    - net: ethernet: mvpp2_main: fix possible OOB write in
+      mvpp2_ethtool_get_rxnfc()
+    - net: ethernet: mtk_eth_soc: fix possible NULL pointer dereference in
+      mtk_hwlro_get_fdir_all()
+    - hsr: Fix uninit-value access in fill_frame_info()
+    - net: dsa: sja1105: hide all multicast addresses from "bridge fdb show"
+    - r8152: check budget for r8152_poll()
+    - kcm: Fix memory leak in error path of kcm_sendmsg()
+    - platform/mellanox: mlxbf-tmfifo: Drop the Rx packet if no more descriptors
+    - platform/mellanox: mlxbf-tmfifo: Drop jumbo frames
+    - platform/mellanox: mlxbf-pmc: Fix potential buffer overflows
+    - platform/mellanox: mlxbf-pmc: Fix reading of unprogrammed events
+    - ipv6: fix ip6_sock_set_addr_preferences() typo
+    - ixgbe: fix timestamp configuration code
+    - kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
+    - MIPS: Only fiddle with CHECKFLAGS if `need-compiler'
+    - drm/amd/display: Fix a bug when searching for insert_above_mpcc
+    - pcd: fix error codes in pcd_init_unit()
+    - Linux 5.15.132
+
+  * CVE-2023-6176
+    - net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
+
+  * CVE-2023-6039
+    - timers: Use del_timer_sync() even on UP
+    - timers: Update kernel-doc for various functions
+    - timers: Rename del_timer_sync() to timer_delete_sync()
+    - timers: Rename del_timer() to timer_delete()
+    - timers: Split [try_to_]del_timer[_sync]() to prepare for shutdown mode
+    - timers: Add shutdown mechanism to the internal functions
+    - timers: Provide timer_shutdown[_sync]()
+    - clocksource/drivers/arm_arch_timer: Do not use timer namespace for
+      timer_shutdown() function
+    - clocksource/drivers/sp804: Do not use timer namespace for timer_shutdown()
+      function
+    - ARM: spear: Do not use timer namespace for timer_shutdown() function
+    - net: usb: lan78xx: reorder cleanup operations to avoid UAF bugs
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Fri, 05 Jan 2024 15:11:36 +0100
+
+linux (5.15.0-91.101) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-91.101 -proposed tracker (LP: #2043452)
+
+  * USB bus error after upgrading to proposed kernel on lunar and jammy
+    (LP: #2043197)
+    - USB: core: Fix oversight in SuperSpeed initialization
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 14 Nov 2023 11:47:55 +0100
+
+linux (5.15.0-90.100) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-90.100 -proposed tracker (LP: #2041603)
+
+  * CVE-2023-25775
+    - RDMA/irdma: Remove irdma_uk_mw_bind()
+    - RDMA/irdma: Remove irdma_sc_send_lsmm_nostag()
+    - RDMA/irdma: Remove irdma_cqp_up_map_cmd()
+    - RDMA/irdma: Remove irdma_get_hw_addr()
+    - RDMA/irdma: Make irdma_uk_cq_init() return a void
+    - RDMA/irdma: optimize rx path by removing unnecessary copy
+    - RDMA/irdma: Remove enum irdma_status_code
+    - RDMA/irdma: Remove excess error variables
+    - RDMA/irdma: Prevent zero-length STAG registration
+
+  * CVE-2023-39189
+    - netfilter: nfnetlink_osf: avoid OOB read
+
+  * SMC stats: Wrong bucket calculation for payload of exactly 4096 bytes
+    (LP: #2039575)
+    - net/smc: Fix pos miscalculation in statistics
+
+  * CVE-2023-45871
+    - igb: set max size RX buffer when store bad packet is enabled
+
+  * CVE-2023-39193
+    - netfilter: xt_sctp: validate the flag_info count
+
+  * CVE-2023-39192
+    - netfilter: xt_u32: validate user space input
+
+  * CVE-2023-31085
+    - ubi: Refuse attaching if mtd's erasesize is 0
+
+  * CVE-2023-5717
+    - perf: Disallow mis-matched inherited group reads
+
+  * CVE-2023-5178
+    - nvmet-tcp: Fix a possible UAF in queue intialization setup
+
+  * CVE-2023-5158
+    - vringh: don't use vringh_kiov_advance() in vringh_iov_xfer()
+
+  * [SRU][J/L/M] UBUNTU: [Packaging] Make WWAN driver a loadable module
+    (LP: #2033406)
+    - [Packaging] Make WWAN driver loadable modules
+
+  * HP ProBook 450 G8 Notebook fail to wifi test (LP: #2037513)
+    - iwlwifi: mvm: Don't fail if PPAG isn't supported
+    - wifi: iwlwifi: fw: skip PPAG for JF
+
+  * usbip: error: failed to open /usr/share/hwdata//usb.ids (LP: #2039439)
+    - [Packaging] Make linux-tools-common depend on hwdata
+
+  * scripts/pahole-flags.sh change return to exit 0 (LP: #2035123)
+    - SAUCE: scripts/pahole-flags.sh change return to exit 0
+
+  * Unable to use nvme drive to install Ubuntu 23.10 (LP: #2040157)
+    - misc: rtsx: Fix some platforms can not boot and move the l1ss judgment to
+      probe
+
+  * Jammy update: v5.15.131 upstream stable release (LP: #2039610)
+    - erofs: ensure that the post-EOF tails are all zeroed
+    - ksmbd: fix wrong DataOffset validation of create context
+    - ksmbd: replace one-element array with flex-array member in struct
+      smb2_ea_info
+    - ARM: pxa: remove use of symbol_get()
+    - mmc: au1xmmc: force non-modular build and remove symbol_get usage
+    - net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index
+    - rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff
+    - modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules
+    - USB: serial: option: add Quectel EM05G variant (0x030e)
+    - USB: serial: option: add FOXCONN T99W368/T99W373 product
+    - ALSA: usb-audio: Fix init call orders for UAC1
+    - usb: dwc3: meson-g12a: do post init to fix broken usb after resumption
+    - usb: chipidea: imx: improve logic if samsung,picophy-* parameter is 0
+    - HID: wacom: remove the battery when the EKR is off
+    - staging: rtl8712: fix race condition
+    - Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race
+      condition
+    - wifi: mt76: mt7921: do not support one stream on secondary antenna only
+    - serial: qcom-geni: fix opp vote on shutdown
+    - serial: sc16is7xx: fix broken port 0 uart init
+    - serial: sc16is7xx: fix bug when first setting GPIO direction
+    - firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe
+    - fsi: master-ast-cf: Add MODULE_FIRMWARE macro
+    - tcpm: Avoid soft reset when partner does not support get_status
+    - nilfs2: fix general protection fault in nilfs_lookup_dirty_data_buffers()
+    - nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
+    - pinctrl: amd: Don't show `Invalid config param` errors
+    - usb: typec: tcpci: move tcpci.h to include/linux/usb/
+    - usb: typec: tcpci: clear the fault status bit
+    - Linux 5.15.131
+
+  * Jammy update: v5.15.130 upstream stable release (LP: #2039608)
+    - ACPI: thermal: Drop nocrt parameter
+    - module: Expose module_init_layout_section()
+    - arm64: module-plts: inline linux/moduleloader.h
+    - arm64: module: Use module_init_layout_section() to spot init sections
+    - ARM: module: Use module_init_layout_section() to spot init sections
+    - rcu: Prevent expedited GP from enabling tick on offline CPU
+    - rcu-tasks: Fix IPI failure handling in trc_wait_for_one_reader
+    - rcu-tasks: Wait for trc_read_check_handler() IPIs
+    - rcu-tasks: Add trc_inspect_reader() checks for exiting critical section
+    - Linux 5.15.130
+
+  * CVE-2023-42754
+    - ipv4: fix null-deref in ipv4_link_failure
+
+  * Jammy update: v5.15.129 upstream stable release (LP: #2039227)
+    - NFSv4.2: fix error handling in nfs42_proc_getxattr
+    - NFSv4: fix out path in __nfs4_get_acl_uncached
+    - xprtrdma: Remap Receive buffers after a reconnect
+    - PCI: acpiphp: Reassign resources on bridge if necessary
+    - dlm: improve plock logging if interrupted
+    - dlm: replace usage of found with dedicated list iterator variable
+    - fs: dlm: add pid to debug log
+    - fs: dlm: change plock interrupted message to debug again
+    - fs: dlm: use dlm_plock_info for do_unlock_close
+    - fs: dlm: fix mismatch of plock results from userspace
+    - MIPS: cpu-features: Enable octeon_cache by cpu_type
+    - MIPS: cpu-features: Use boot_cpu_type for CPU type based features
+    - fbdev: Improve performance of sys_imageblit()
+    - fbdev: Fix sys_imageblit() for arbitrary image widths
+    - fbdev: fix potential OOB read in fast_imageblit()
+    - ALSA: pcm: Fix potential data race at PCM memory allocation helpers
+    - jbd2: remove t_checkpoint_io_list
+    - jbd2: remove journal_clean_one_cp_list()
+    - jbd2: fix a race when checking checkpoint buffer busy
+    - can: raw: fix receiver memory leak
+    - drm/amd/display: do not wait for mpc idle if tg is disabled
+    - drm/amd/display: check TG is non-null before checking if enabled
+    - can: raw: fix lockdep issue in raw_release()
+    - tracing: Fix cpu buffers unavailable due to 'record_disabled' missed
+    - tracing: Fix memleak due to race between current_tracer and trace
+    - octeontx2-af: SDP: fix receive link config
+    - sock: annotate data-races around prot->memory_pressure
+    - dccp: annotate data-races in dccp_poll()
+    - ipvlan: Fix a reference count leak warning in ipvlan_ns_exit()
+    - net: bgmac: Fix return value check for fixed_phy_register()
+    - net: bcmgenet: Fix return value check for fixed_phy_register()
+    - net: validate veth and vxcan peer ifindexes
+    - ice: fix receive buffer size miscalculation
+    - igb: Avoid starting unnecessary workqueues
+    - igc: Fix the typo in the PTM Control macro
+    - net/sched: fix a qdisc modification with ambiguous command request
+    - netfilter: nf_tables: flush pending destroy work before netlink notifier
+    - netfilter: nf_tables: fix out of memory error handling
+    - rtnetlink: return ENODEV when ifname does not exist and group is given
+    - rtnetlink: Reject negative ifindexes in RTM_NEWLINK
+    - net: remove bond_slave_has_mac_rcu()
+    - bonding: fix macvlan over alb bond support
+    - net/ncsi: make one oem_gma function for all mfr id
+    - net/ncsi: change from ndo_set_mac_address to dev_set_mac_address
+    - ibmveth: Use dcbf rather than dcbfl
+    - NFSv4: Fix dropped lock for racing OPEN and delegation return
+    - clk: Fix slab-out-of-bounds error in devm_clk_release()
+    - ALSA: ymfpci: Fix the missing snd_card_free() call at probe error
+    - mm: add a call to flush_cache_vmap() in vmap_pfn()
+    - NFS: Fix a use after free in nfs_direct_join_group()
+    - nfsd: Fix race to FREE_STATEID and cl_revoked
+    - selinux: set next pointer before attaching to list
+    - batman-adv: Trigger events for auto adjusted MTU
+    - batman-adv: Don't increase MTU when set by user
+    - batman-adv: Do not get eth header before batadv_check_management_packet
+    - batman-adv: Fix TT global entry leak when client roamed back
+    - batman-adv: Fix batadv_v_ogm_aggr_send memory leak
+    - batman-adv: Hold rtnl lock during MTU update via netlink
+    - lib/clz_ctz.c: Fix __clzdi2() and __ctzdi2() for 32-bit kernels
+    - radix tree: remove unused variable
+    - of: unittest: Fix EXPECT for parse_phandle_with_args_map() test
+    - of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock
+    - media: vcodec: Fix potential array out-of-bounds in encoder queue_setup
+    - PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root
+      bus
+    - drm/vmwgfx: Fix shader stage validation
+    - drm/display/dp: Fix the DP DSC Receiver cap size
+    - x86/fpu: Invalidate FPU state correctly on exec()
+    - nfs: use vfs setgid helper
+    - nfsd: use vfs setgid helper
+    - torture: Fix hang during kthread shutdown phase
+    - cgroup/cpuset: Rename functions dealing with DEADLINE accounting
+    - sched/cpuset: Bring back cpuset_mutex
+    - sched/cpuset: Keep track of SCHED_DEADLINE task in cpusets
+    - cgroup/cpuset: Iterate only if DEADLINE tasks are present
+    - sched/deadline: Create DL BW alloc, free & check overflow interface
+    - cgroup/cpuset: Free DL BW in case can_attach() fails
+    - drm/i915: Fix premature release of request's reusable memory
+    - can: raw: add missing refcount for memory leak fix
+    - scsi: snic: Fix double free in snic_tgt_create()
+    - scsi: core: raid_class: Remove raid_component_add()
+    - clk: Fix undefined reference to `clk_rate_exclusive_{get,put}'
+    - pinctrl: renesas: rza2: Add lock around
+      pinctrl_generic{{add,remove}_group,{add,remove}_function}
+    - dma-buf/sw_sync: Avoid recursive lock during fence signal
+    - mm: memory-failure: kill soft_offline_free_page()
+    - mm: memory-failure: fix unexpected return value in soft_offline_page()
+    - mm,ima,kexec,of: use memblock_free_late from ima_free_kexec_buffer
+    - Linux 5.15.129
+
+  * Jammy update: v5.15.128 upstream stable release (LP: #2038486)
+    - mmc: sdhci-f-sdh30: Replace with sdhci_pltfm
+    - selftests: forwarding: tc_actions: cleanup temporary files when test is
+      aborted
+    - selftests: forwarding: tc_actions: Use ncat instead of nc
+    - macsec: Fix traffic counters/statistics
+    - macsec: use DEV_STATS_INC()
+    - net/tls: Perform immediate device ctx cleanup when possible
+    - net/tls: Multi-threaded calls to TX tls_dev_del
+    - net: tls: avoid discarding data on record close
+    - PCI: tegra194: Fix possible array out of bounds access
+    - ARM: dts: imx6dl: prtrvt, prtvt7, prti6q, prtwd2: fix USB related warnings
+    - iopoll: Call cpu_relax() in busy loops
+    - ASoC: SOF: Intel: fix SoundWire/HDaudio mutual exclusion
+    - dma-remap: use kvmalloc_array/kvfree for larger dma memory remap
+    - HID: logitech-hidpp: Add USB and Bluetooth IDs for the Logitech G915 TKL
+      Keyboard
+    - HID: add quirk for 03f0:464a HP Elite Presenter Mouse
+    - RDMA/mlx5: Return the firmware result upon destroying QP/RQ
+    - ovl: check type and offset of struct vfsmount in ovl_entry
+    - smb: client: fix warning in cifs_smb3_do_mount()
+    - media: v4l2-mem2mem: add lock to protect parameter num_rdy
+    - usb: gadget: u_serial: Avoid spinlock recursion in __gs_console_push
+    - media: platform: mediatek: vpu: fix NULL ptr dereference
+    - thunderbolt: Read retimer NVM authentication status prior
+      tb_retimer_set_inbound_sbtx()
+    - usb: chipidea: imx: don't request QoS for imx8ulp
+    - usb: chipidea: imx: add missing USB PHY DPDM wakeup setting
+    - gfs2: Fix possible data races in gfs2_show_options()
+    - pcmcia: rsrc_nonstatic: Fix memory leak in nonstatic_release_resource_db()
+    - firewire: net: fix use after free in fwnet_finish_incoming_packet()
+    - watchdog: sp5100_tco: support Hygon FCH/SCH (Server Controller Hub)
+    - Bluetooth: L2CAP: Fix use-after-free
+    - Bluetooth: btusb: Add MT7922 bluetooth ID for the Asus Ally
+    - drm/amdgpu: Fix potential fence use-after-free v2
+    - fs/ntfs3: Enhance sanity check while generating attr_list
+    - fs: ntfs3: Fix possible null-pointer dereferences in mi_read()
+    - fs/ntfs3: Mark ntfs dirty when on-disk struct is corrupted
+    - ALSA: hda/realtek: Add quirks for Unis H3C Desktop B760 & Q760
+    - ALSA: hda: fix a possible null-pointer dereference due to data race in
+      snd_hdac_regmap_sync()
+    - powerpc/kasan: Disable KCOV in KASAN code
+    - ring-buffer: Do not swap cpu_buffer during resize process
+    - iio: add addac subdirectory
+    - iio: adc: stx104: Utilize iomap interface
+    - iio: adc: stx104: Implement and utilize register structures
+    - iio: stx104: Move to addac subdirectory
+    - iio: addac: stx104: Fix race condition for stx104_write_raw()
+    - iio: addac: stx104: Fix race condition when converting analog-to-digital
+    - igc: read before write to SRRCTL register
+    - ARM: dts: aspeed: asrock: Correct firmware flash SPI clocks
+    - drm/amd/display: save restore hdcp state when display is unplugged from mst
+      hub
+    - drm/amd/display: phase3 mst hdcp for multiple displays
+    - drm/amd/display: fix access hdcp_workqueue assert
+    - usb: dwc3: gadget: Synchronize IRQ between soft connect/disconnect
+    - usb: dwc3: Remove DWC3 locking during gadget suspend/resume
+    - usb: dwc3: Fix typos in gadget.c
+    - USB: dwc3: gadget: drop dead hibernation code
+    - usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()
+    - tty: serial: fsl_lpuart: Add i.MXRT1050 support
+    - tty: serial: fsl_lpuart: make rx_watermark configurable for different
+      platforms
+    - tty: serial: fsl_lpuart: reduce RX watermark to 0 on LS1028A
+    - USB: dwc3: qcom: fix NULL-deref on suspend
+    - USB: dwc3: fix use-after-free on core driver unbind
+    - mmc: bcm2835: fix deferred probing
+    - mmc: sunxi: fix deferred probing
+    - ARM: dts: imx6sll: fixup of operating points
+    - ARM: dts: nxp/imx6sll: fix wrong property name in usbphy node
+    - btrfs: move out now unused BG from the reclaim list
+    - virtio-mmio: don't break lifecycle of vm_dev
+    - vduse: Use proper spinlock for IRQ injection
+    - cifs: fix potential oops in cifs_oplock_break
+    - i2c: bcm-iproc: Fix bcm_iproc_i2c_isr deadlock issue
+    - i2c: hisi: Only handle the interrupt of the driver's transfer
+    - fbdev: mmp: fix value check in mmphw_probe()
+    - powerpc/rtas_flash: allow user copy to flash block cache objects
+    - tty: n_gsm: fix the UAF caused by race condition in gsm_cleanup_mux
+    - tty: serial: fsl_lpuart: Clear the error flags by writing 1 for lpuart32
+      platforms
+    - btrfs: fix BUG_ON condition in btrfs_cancel_balance
+    - i2c: designware: Correct length byte validation logic
+    - i2c: designware: Handle invalid SMBus block data response length value
+    - net: xfrm: Fix xfrm_address_filter OOB read
+    - net: af_key: fix sadb_x_filter validation
+    - net: xfrm: Amend XFRMA_SEC_CTX nla_policy structure
+    - xfrm: fix slab-use-after-free in decode_session6
+    - ip6_vti: fix slab-use-after-free in decode_session6
+    - ip_vti: fix potential slab-use-after-free in decode_session6
+    - xfrm: add forgotten nla_policy for XFRMA_MTIMER_THRESH
+    - net: phy: fix IRQ-based wake-on-lan over hibernate / power off
+    - selftests: mirror_gre_changes: Tighten up the TTL test match
+    - drm/panel: simple: Fix AUO G121EAN01 panel timings according to the docs
+    - netfilter: nf_tables: fix false-positive lockdep splat
+    - ipvs: fix racy memcpy in proc_do_sync_threshold
+    - net: phy: broadcom: stub c45 read/write for 54810
+    - team: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
+    - iavf: fix FDIR rule fields masks validation
+    - i40e: fix misleading debug logs
+    - net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset
+    - sock: Fix misuse of sk_under_memory_pressure()
+    - net: do not allow gso_size to be set to GSO_BY_FRAGS
+    - bus: ti-sysc: Flush posted write on enable before reset
+    - arm64: dts: qcom: qrb5165-rb5: fix thermal zone conflict
+    - ARM: dts: imx: Set default tuning step for imx6sx usdhc
+    - ASoC: rt5665: add missed regulator_bulk_disable
+    - ASoC: meson: axg-tdm-formatter: fix channel slot allocation
+    - soc: aspeed: socinfo: Add kfree for kstrdup
+    - ALSA: hda/realtek - Remodified 3k pull low procedure
+    - riscv: uaccess: Return the number of bytes effectively not copied
+    - serial: 8250: Fix oops for port->pm on uart_change_pm()
+    - ALSA: usb-audio: Add support for Mythware XA001AU capture and playback
+      interfaces.
+    - cifs: Release folio lock on fscache read hit.
+    - mmc: wbsd: fix double mmc_free_host() in wbsd_init()
+    - mmc: block: Fix in_flight[issue_type] value error
+    - drm/qxl: fix UAF on handle creation
+    - drm/amd: flush any delayed gfxoff on suspend entry
+    - netfilter: set default timeout to 3 secs for sctp shutdown send and recv
+      state
+    - arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4
+    - virtio-net: set queues after driver_ok
+    - net: fix the RTO timer retransmitting skb every 1ms if linear option is
+      enabled
+    - mmc: f-sdh30: fix order of function calls in sdhci_f_sdh30_remove
+    - Linux 5.15.128
+
+  * Jammy update: v5.15.127 upstream stable release (LP: #2038382)
+    - ksmbd: validate command request size
+    - ksmbd: fix wrong next length validation of ea buffer in smb2_set_ea()
+    - wireguard: allowedips: expand maximum node depth
+    - mmc: moxart: read scr register without changing byte order
+    - ipv6: adjust ndisc_is_useropt() to also return true for PIO
+    - dmaengine: pl330: Return DMA_PAUSED when transaction is paused
+    - riscv,mmio: Fix readX()-to-delay() ordering
+    - drm/nouveau/gr: enable memory loads on helper invocation on all channels
+    - drm/shmem-helper: Reset vma->vm_ops before calling dma_buf_mmap()
+    - drm/amd/display: check attr flag before set cursor degamma on DCN3+
+    - hwmon: (pmbus/bel-pfe) Enable PMBUS_SKIP_STATUS_CHECK for pfe1100
+    - radix tree test suite: fix incorrect allocation size for pthreads
+    - nilfs2: fix use-after-free of nilfs_root in dirtying inodes via iput
+    - bpf: allow precision tracking for programs with subprogs
+    - bpf: stop setting precise in current state
+    - bpf: aggressively forget precise markings during state checkpointing
+    - selftests/bpf: make test_align selftest more robust
+    - selftests/bpf: Workaround verification failure for
+      fexit_bpf2bpf/func_replace_return_code
+    - selftests/bpf: Fix sk_assign on s390x
+    - io_uring: correct check for O_TMPFILE
+    - iio: cros_ec: Fix the allocation size for cros_ec_command
+    - iio: adc: ina2xx: avoid NULL pointer dereference on OF device match
+    - binder: fix memory leak in binder_init()
+    - misc: rtsx: judge ASPM Mode to set PETXCFG Reg
+    - usb-storage: alauda: Fix uninit-value in alauda_check_media()
+    - usb: dwc3: Properly handle processing of pending events
+    - usb: common: usb-conn-gpio: Prevent bailing out if initial role is none
+    - usb: typec: tcpm: Fix response to vsafe0V event
+    - x86/cpu/amd: Enable Zenbleed fix for AMD Custom APU 0405
+    - x86/mm: Fix VDSO and VVAR placement on 5-level paging machines
+    - x86/speculation: Add cpu_show_gds() prototype
+    - x86: Move gds_ucode_mitigated() declaration to header
+    - drm/nouveau/disp: Revert a NULL check inside nouveau_connector_get_modes
+    - selftests/rseq: Fix build with undefined __weak
+    - selftests: forwarding: Add a helper to skip test when using veth pairs
+    - selftests: forwarding: ethtool: Skip when using veth pairs
+    - selftests: forwarding: ethtool_extended_state: Skip when using veth pairs
+    - selftests: forwarding: Skip test when no interfaces are specified
+    - selftests: forwarding: Switch off timeout
+    - selftests: forwarding: tc_flower: Relax success criterion
+    - net: core: remove unnecessary frame_sz check in bpf_xdp_adjust_tail()
+    - bpf, sockmap: Fix map type error in sock_map_del_link
+    - bpf, sockmap: Fix bug that strp_done cannot be called
+    - mISDN: Update parameter type of dsp_cmx_send()
+    - net/packet: annotate data-races around tp->status
+    - tunnels: fix kasan splat when generating ipv4 pmtu error
+    - xsk: fix refcount underflow in error path
+    - bonding: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
+    - dccp: fix data-race around dp->dccps_mss_cache
+    - drivers: net: prevent tun_build_skb() to exceed the packet size limit
+    - iavf: fix potential races for FDIR filters
+    - IB/hfi1: Fix possible panic during hotplug remove
+    - drm/rockchip: Don't spam logs in atomic check
+    - wifi: cfg80211: fix sband iftype data lookup for AP_VLAN
+    - RDMA/umem: Set iova in ODP flow
+    - net: phy: at803x: remove set/get wol callbacks for AR8032
+    - net: hns3: refactor hclge_mac_link_status_wait for interface reuse
+    - net: hns3: add wait until mac link down
+    - nexthop: Fix infinite nexthop dump when using maximum nexthop ID
+    - nexthop: Make nexthop bucket dump more efficient
+    - nexthop: Fix infinite nexthop bucket dump when using maximum nexthop ID
+    - dmaengine: mcf-edma: Fix a potential un-allocated memory access
+    - net/mlx5: Allow 0 for total host VFs
+    - net/mlx5: Skip clock update work when device is in error state
+    - ibmvnic: Enforce stronger sanity checks on login response
+    - ibmvnic: Unmap DMA login rsp buffer on send login fail
+    - ibmvnic: Handle DMA unmapping of login buffs in release functions
+    - btrfs: don't stop integrity writeback too early
+    - btrfs: exit gracefully if reloc roots don't match
+    - btrfs: reject invalid reloc tree root keys with stack dump
+    - btrfs: set cache_block_group_error if we find an error
+    - nvme-tcp: fix potential unbalanced freeze & unfreeze
+    - nvme-rdma: fix potential unbalanced freeze & unfreeze
+    - netfilter: nf_tables: report use refcount overflow
+    - scsi: core: Fix legacy /proc parsing buffer overflow
+    - scsi: storvsc: Fix handling of virtual Fibre Channel timeouts
+    - scsi: 53c700: Check that command slot is not NULL
+    - scsi: snic: Fix possible memory leak if device_add() fails
+    - scsi: core: Fix possible memory leak if device_add() fails
+    - scsi: fnic: Replace return codes in fnic_clean_pending_aborts()
+    - scsi: qedi: Fix firmware halt over suspend and resume
+    - scsi: qedf: Fix firmware halt over suspend and resume
+    - alpha: remove __init annotation from exported page_is_ram()
+    - sch_netem: fix issues in netem_change() vs get_dist_table()
+    - tick: Detect and fix jiffies update stall
+    - timers/nohz: Switch to ONESHOT_STOPPED in the low-res handler when the tick
+      is stopped
+    - timers/nohz: Last resort update jiffies on nohz_full IRQ entry
+    - Linux 5.15.127
+    - Upstream stable to v5.15.127
+
+  * CVE-2023-37453
+    - USB: core: Unite old scheme and new scheme descriptor reads
+    - USB: core: Change usb_get_device_descriptor() API
+    - USB: core: Fix race by not overwriting udev->descriptor in hub_port_init()
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Mon, 30 Oct 2023 12:40:14 +0100
+
+linux (5.15.0-88.98) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-88.98 -proposed tracker (LP: #2038055)
+
+  * CVE-2023-4244
+    - netfilter: nf_tables: don't skip expired elements during walk
+    - netfilter: nf_tables: adapt set backend to use GC transaction API
+    - netfilter: nft_set_hash: mark set element as dead when deleting from packet
+      path
+    - netfilter: nf_tables: GC transaction API to avoid race with control plane
+    - netfilter: nf_tables: remove busy mark and gc batch API
+    - netfilter: nf_tables: don't fail inserts if duplicate has expired
+    - netfilter: nf_tables: fix kdoc warnings after gc rework
+    - netfilter: nf_tables: fix GC transaction races with netns and netlink event
+      exit path
+    - netfilter: nf_tables: GC transaction race with netns dismantle
+    - netfilter: nf_tables: GC transaction race with abort path
+    - netfilter: nf_tables: use correct lock to protect gc_list
+    - netfilter: nf_tables: defer gc run if previous batch is still pending
+    - netfilter: nft_dynset: disallow object maps
+    - netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
+
+  * CVE-2023-42756
+    - netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
+
+  * CVE-2023-4623
+    - net/sched: sch_hfsc: Ensure inner classes have fsc curve
+
+  * PCI BARs larger than 128GB are disabled (LP: #2037403)
+    - PCI: Support BAR sizes up to 8TB
+
+  * Fix unstable audio at low levels on Thinkpad P1G4 (LP: #2037077)
+    - ALSA: hda/realtek - ALC287 I2S speaker platform support
+
+  * Check for changes relevant for security certifications (LP: #1945989)
+    - [Packaging] Add a new fips-checks script
+
+  * Jammy update: v5.15.126 upstream stable release (LP: #2037593)
+    - io_uring: gate iowait schedule on having pending requests
+    - perf: Fix function pointer case
+    - net/mlx5: Free irqs only on shutdown callback
+    - arm64: errata: Add workaround for TSB flush failures
+    - arm64: errata: Add detection for TRBE write to out-of-range
+    - [Config] updateconfigs for ARM64_ERRATUM_ and
+      ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+    - iommu/arm-smmu-v3: Work around MMU-600 erratum 1076982
+    - iommu/arm-smmu-v3: Document MMU-700 erratum 2812531
+    - iommu/arm-smmu-v3: Add explicit feature for nesting
+    - iommu/arm-smmu-v3: Document nesting-related errata
+    - arm64: dts: imx8mn-var-som: add missing pull-up for onboard PHY reset pinmux
+    - word-at-a-time: use the same return type for has_zero regardless of
+      endianness
+    - KVM: s390: fix sthyi error handling
+    - wifi: cfg80211: Fix return value in scan logic
+    - net/mlx5: DR, fix memory leak in mlx5dr_cmd_create_reformat_ctx
+    - net/mlx5e: fix return value check in mlx5e_ipsec_remove_trailer()
+    - bpf: Add length check for SK_DIAG_BPF_STORAGE_REQ_MAP_FD parsing
+    - rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length
+    - net: dsa: fix value check in bcm_sf2_sw_probe()
+    - perf test uprobe_from_different_cu: Skip if there is no gcc
+    - net: sched: cls_u32: Fix match key mis-addressing
+    - mISDN: hfcpci: Fix potential deadlock on &hc->lock
+    - qed: Fix kernel-doc warnings
+    - qed: Fix scheduling in a tasklet while getting stats
+    - net: annotate data-races around sk->sk_max_pacing_rate
+    - net: add missing READ_ONCE(sk->sk_rcvlowat) annotation
+    - net: add missing READ_ONCE(sk->sk_sndbuf) annotation
+    - net: add missing READ_ONCE(sk->sk_rcvbuf) annotation
+    - net: add missing data-race annotations around sk->sk_peek_off
+    - net: add missing data-race annotation for sk_ll_usec
+    - net/sched: taprio: Limit TCA_TAPRIO_ATTR_SCHED_CYCLE_TIME to INT_MAX.
+    - bpf, cpumap: Handle skb as well when clean up ptr_ring
+    - bpf: sockmap: Remove preempt_disable in sock_map_sk_acquire
+    - net: ll_temac: Switch to use dev_err_probe() helper
+    - net: ll_temac: fix error checking of irq_of_parse_and_map()
+    - net: korina: handle clk prepare error in korina_probe()
+    - net: netsec: Ignore 'phy-mode' on SynQuacer in DT mode
+    - net: dcb: choose correct policy to parse DCB_ATTR_BCN
+    - s390/qeth: Don't call dev_close/dev_open (DOWN/UP)
+    - ip6mr: Fix skb_under_panic in ip6mr_cache_report()
+    - vxlan: Fix nexthop hash size
+    - net/mlx5: fs_core: Make find_closest_ft more generic
+    - net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio
+    - prestera: fix fallback to previous version on same major version
+    - tcp_metrics: fix addr_same() helper
+    - tcp_metrics: annotate data-races around tm->tcpm_stamp
+    - tcp_metrics: annotate data-races around tm->tcpm_lock
+    - tcp_metrics: annotate data-races around tm->tcpm_vals[]
+    - tcp_metrics: annotate data-races around tm->tcpm_net
+    - tcp_metrics: fix data-race in tcpm_suck_dst() vs fastopen
+    - scsi: zfcp: Defer fc_rport blocking until after ADISC response
+    - scsi: storvsc: Limit max_sectors for virtual Fibre Channel devices
+    - libceph: fix potential hang in ceph_osdc_notify()
+    - USB: zaurus: Add ID for A-300/B-500/C-700
+    - ceph: defer stopping mdsc delayed_work
+    - firmware: arm_scmi: Drop OF node reference in the transport channel setup
+    - exfat: use kvmalloc_array/kvfree instead of kmalloc_array/kfree
+    - exfat: release s_lock before calling dir_emit()
+    - mtd: spinand: toshiba: Fix ecc_get_status
+    - mtd: rawnand: meson: fix OOB available bytes for ECC
+    - arm64: dts: stratix10: fix incorrect I2C property for SCL signal
+    - wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
+    - rbd: prevent busy loop when requesting exclusive lock
+    - bpf: Disable preemption in bpf_event_output
+    - open: make RESOLVE_CACHED correctly test for O_TMPFILE
+    - drm/ttm: check null pointer before accessing when swapping
+    - bpf, cpumap: Make sure kthread is running before map update returns
+    - file: reinstate f_pos locking optimization for regular files
+    - fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_load_attr_list()
+    - fs/sysv: Null check to prevent null-ptr-deref bug
+    - net: usbnet: Fix WARNING in usbnet_start_xmit/usb_submit_urb
+    - fs: Protect reconfiguration of sb read-write from racing writes
+    - ext2: Drop fragment support
+    - mtd: rawnand: omap_elm: Fix incorrect type in assignment
+    - mtd: rawnand: rockchip: fix oobfree offset and description
+    - mtd: rawnand: rockchip: Align hwecc vs. raw page helper layouts
+    - mtd: rawnand: fsl_upm: Fix an off-by one test in fun_exec_op()
+    - powerpc/mm/altmap: Fix altmap boundary check
+    - drm/imx/ipuv3: Fix front porch adjustment upon hactive aligning
+    - selftests/rseq: check if libc rseq support is registered
+    - selftests/rseq: Play nice with binaries statically linked against glibc
+      2.35+
+    - soundwire: bus: pm_runtime_request_resume on peripheral attachment
+    - soundwire: fix enumeration completion
+    - PM / wakeirq: support enabling wake-up irq after runtime_suspend called
+    - PM: sleep: wakeirq: fix wake irq arming
+    - Linux 5.15.126
+
+  * Jammy update: v5.15.125 upstream stable release (LP: #2036843)
+    - ia64/cpu: Switch to arch_cpu_finalize_init()
+    - m68k/cpu: Switch to arch_cpu_finalize_init()
+    - mips/cpu: Switch to arch_cpu_finalize_init()
+    - sh/cpu: Switch to arch_cpu_finalize_init()
+    - Linux 5.15.125
+    - Upstream stable to v5.15.125
+
+  * CVE-2023-42755
+    - net/sched: Retire rsvp classifier
+    - [Config] remove NET_CLS_RSVP and NET_CLS_RSVP6
+
+  * CVE-2023-42753
+    - netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for
+      ip_set_hash_netportnet.c
+
+  * CVE-2023-34319
+    - xen/netback: Fix buffer overrun triggered by unusual packet
+
+  * CVE-2023-5197
+    - netfilter: nf_tables: disallow rule removal from chain binding
+
+  * CVE-2023-4921
+    - net: sched: sch_qfq: Fix UAF in qfq_dequeue()
+
+  * CVE-2023-42752
+    - igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
+
+  * Avoid address overwrite in kernel_connect (LP: #2035163)
+    - net: Avoid address overwrite in kernel_connect
+
+  * NULL Pointer Dereference During KVM MMU Page Invalidation (LP: #2035166)
+    - KVM: x86/mmu: Track the number of TDP MMU pages, but not the actual pages
+
+  * Fix suspend hang on Lenovo workstation (LP: #2034479)
+    - igb: Fix igb_down hung on surprise removal
+
+  * [regression] Unable to initialize SGX enclaves with XFRM other than 3
+    (LP: #2034745)
+    - x86/fpu: Set X86_FEATURE_OSXSAVE feature after enabling OSXSAVE in CR4
+
+  * CVE-2023-4881
+    - netfilter: nftables: exthdr: fix 4-byte stack OOB write
+
+  * CVE-2023-4622
+    - af_unix: Fix null-ptr-deref in unix_stream_sendpage().
+
+  * Jammy update: v5.15.124 upstream stable release (LP: #2035400)
+    - jbd2: Fix wrongly judgement for buffer head removing while doing checkpoint
+    - KVM: s390: pv: fix index value of replaced ASCE
+    - io_uring: don't audit the capability check in io_uring_create()
+    - gpio: tps68470: Make tps68470_gpio_output() always set the initial value
+    - pwm: Add a stub for devm_pwmchip_add()
+    - gpio: mvebu: Make use of devm_pwmchip_add
+    - gpio: mvebu: fix irq domain leak
+    - btrfs: fix race between quota disable and relocation
+    - i2c: Delete error messages for failed memory allocations
+    - i2c: Improve size determinations
+    - i2c: nomadik: Remove unnecessary goto label
+    - i2c: nomadik: Use devm_clk_get_enabled()
+    - i2c: nomadik: Remove a useless call in the remove function
+    - PCI/ASPM: Return 0 or -ETIMEDOUT from pcie_retrain_link()
+    - PCI/ASPM: Factor out pcie_wait_for_retrain()
+    - PCI/ASPM: Avoid link retraining race
+    - PCI: rockchip: Remove writes to unused registers
+    - PCI: rockchip: Fix window mapping and address translation for endpoint
+    - PCI: rockchip: Don't advertise MSI-X in PCIe capabilities
+    - dlm: cleanup plock_op vs plock_xop
+    - dlm: rearrange async condition return
+    - fs: dlm: interrupt posix locks only when process is killed
+    - drm/ttm: Don't print error message if eviction was interrupted
+    - drm/ttm: Don't leak a resource on eviction error
+    - n_tty: Rename tail to old_tail in n_tty_read()
+    - tty: fix hang on tty device with no_room set
+    - drm/ttm: never consider pinned BOs for eviction&swap
+    - cifs: missing directory in MAINTAINERS file
+    - cifs: use fs_context for automounts
+    - ksmbd: remove internal.h include
+    - cifs: if deferred close is disabled then close files immediately
+    - pwm: meson: Simplify duplicated per-channel tracking
+    - pwm: meson: fix handling of period/duty if greater than UINT_MAX
+    - tracing/probes: Add symstr type for dynamic events
+    - tracing/probes: Fix to avoid double count of the string length on the array
+    - tracing: Allow synthetic events to pass around stacktraces
+    - Revert "tracing: Add "(fault)" name injection to kernel probes"
+    - tracing/probes: Fix to record 0-length data_loc in fetch_store_string*() if
+      fails
+    - scsi: qla2xxx: Remove unused declarations for qla2xxx
+    - scsi: qla2xxx: Multi-que support for TMF
+    - scsi: qla2xxx: Fix task management cmd failure
+    - scsi: qla2xxx: Fix task management cmd fail due to unavailable resource
+    - scsi: qla2xxx: Add debug prints in the device remove path
+    - scsi: qla2xxx: Fix hang in task management
+    - drm/amdgpu: fix vkms crtc settings
+    - drm/amdgpu/vkms: relax timer deactivation by hrtimer_try_to_cancel
+    - phy: qcom-snps: Use dev_err_probe() to simplify code
+    - phy: qcom-snps: correct struct qcom_snps_hsphy kerneldoc
+    - phy: qcom-snps-femto-v2: keep cfg_ahb_clk enabled during runtime suspend
+    - phy: qcom-snps-femto-v2: properly enable ref clock
+    - soundwire: qcom: update status correctly with mask
+    - media: staging: atomisp: select V4L2_FWNODE
+    - i40e: Fix an NULL vs IS_ERR() bug for debugfs_create_dir()
+    - iavf: fix potential deadlock on allocation failure
+    - iavf: check for removal state before IAVF_FLAG_PF_COMMS_FAILED
+    - net: phy: marvell10g: fix 88x3310 power up
+    - net: hns3: fix wrong tc bandwidth weight data issue
+    - net: hns3: fix wrong bw weight of disabled tc issue
+    - vxlan: move to its own directory
+    - vxlan: calculate correct header length for GPE
+    - phy: hisilicon: Fix an out of bounds check in hisi_inno_phy_probe()
+    - ethernet: atheros: fix return value check in atl1e_tso_csum()
+    - ipv6 addrconf: fix bug where deleting a mngtmpaddr can create a new
+      temporary address
+    - ice: Fix memory management in ice_ethtool_fdir.c
+    - bonding: reset bond's flags when down link is P2P device
+    - team: reset team's flags when down link is P2P device
+    - net: stmmac: Apply redundant write work around on 4.xx too
+    - platform/x86: msi-laptop: Fix rfkill out-of-sync on MSI Wind U100
+    - igc: Fix Kernel Panic during ndo_tx_timeout callback
+    - netfilter: nft_set_rbtree: fix overlap expiration walk
+    - net/sched: mqprio: refactor nlattr parsing to a separate function
+    - net/sched: mqprio: add extack to mqprio_parse_nlattr()
+    - net/sched: mqprio: Add length check for TCA_MQPRIO_{MAX/MIN}_RATE64
+    - benet: fix return value check in be_lancer_xmit_workarounds()
+    - tipc: check return value of pskb_trim()
+    - tipc: stop tipc crypto on failure in tipc_node_create
+    - RDMA/mlx4: Make check for invalid flags stricter
+    - drm/msm/dpu: drop enum dpu_core_perf_data_bus_id
+    - drm/msm/adreno: Fix snapshot BINDLESS_DATA size
+    - RDMA/irdma: Add missing read barriers
+    - RDMA/irdma: Fix data race on CQP completion stats
+    - RDMA/irdma: Fix data race on CQP request done
+    - RDMA/mthca: Fix crash when polling CQ for shared QPs
+    - RDMA/bnxt_re: Prevent handling any completions after qp destroy
+    - drm/msm: Fix IS_ERR_OR_NULL() vs NULL check in a5xx_submit_in_rb()
+    - ASoC: fsl_spdif: Silence output on stop
+    - block: Fix a source code comment in include/uapi/linux/blkzoned.h
+    - dm raid: fix missing reconfig_mutex unlock in raid_ctr() error paths
+    - dm raid: clean up four equivalent goto tags in raid_ctr()
+    - dm raid: protect md_stop() with 'reconfig_mutex'
+    - drm/amd: Fix an error handling mistake in psp_sw_init()
+    - RDMA/irdma: Report correct WC error
+    - ata: pata_ns87415: mark ns87560_tf_read static
+    - ring-buffer: Fix wrong stat of cpu_buffer->read
+    - tracing: Fix warning in trace_buffered_event_disable()
+    - Revert "usb: gadget: tegra-xudc: Fix error check in
+      tegra_xudc_powerdomain_init()"
+    - usb: gadget: call usb_gadget_check_config() to verify UDC capability
+    - USB: gadget: Fix the memory leak in raw_gadget driver
+    - KVM: Grab a reference to KVM for VM and vCPU stats file descriptors
+    - KVM: VMX: Don't fudge CR0 and CR4 for restricted L2 guest
+    - serial: qcom-geni: drop bogus runtime pm state update
+    - serial: 8250_dw: Preserve original value of DLF register
+    - serial: sifive: Fix sifive_serial_console_setup() section
+    - USB: serial: option: support Quectel EM060K_128
+    - USB: serial: option: add Quectel EC200A module support
+    - USB: serial: simple: add Kaufmann RKS+CAN VCP
+    - USB: serial: simple: sort driver entries
+    - can: gs_usb: gs_can_close(): add missing set of CAN state to
+      CAN_STATE_STOPPED
+    - Revert "usb: dwc3: core: Enable AutoRetry feature in the controller"
+    - usb: dwc3: pci: skip BYT GPIO lookup table for hardwired phy
+    - usb: dwc3: don't reset device side if dwc3 was configured as host-only
+    - usb: ohci-at91: Fix the unhandle interrupt when resume
+    - USB: quirks: add quirk for Focusrite Scarlett
+    - usb: cdns3: fix incorrect calculation of ep_buf_size when more than one
+      config
+    - usb: xhci-mtk: set the dma max_seg_size
+    - Revert "usb: xhci: tegra: Fix error check"
+    - Documentation: security-bugs.rst: update preferences when dealing with the
+      linux-distros group
+    - Documentation: security-bugs.rst: clarify CVE handling
+    - staging: r8712: Fix memory leak in _r8712_init_xmit_priv()
+    - staging: ks7010: potential buffer overflow in ks_wlan_set_encode_ext()
+    - tty: n_gsm: fix UAF in gsm_cleanup_mux
+    - Revert "xhci: add quirk for host controllers that don't update endpoint DCS"
+    - ALSA: hda/relatek: Enable Mute LED on HP 250 G8
+    - hwmon: (k10temp) Enable AMD3255 Proc to show negative temperature
+    - hwmon: (nct7802) Fix for temp6 (PECI1) processed even if PECI1 disabled
+    - btrfs: check if the transaction was aborted at btrfs_wait_for_commit()
+    - btrfs: check for commit error at btrfs_attach_transaction_barrier()
+    - file: always lock position for FMODE_ATOMIC_POS
+    - nfsd: Remove incorrect check in nfsd4_validate_stateid
+    - tpm_tis: Explicitly check for error code
+    - irq-bcm6345-l1: Do not assume a fixed block to cpu mapping
+    - irqchip/gic-v4.1: Properly lock VPEs when doing a directLPI invalidation
+    - locking/rtmutex: Fix task->pi_waiters integrity
+    - KVM: x86: Disallow KVM_SET_SREGS{2} if incoming CR0 is invalid
+    - virtio-net: fix race between set queues and probe
+    - s390/dasd: fix hanging device after quiesce/resume
+    - ASoC: wm8904: Fill the cache for WM8904_ADC_TEST_0 register
+    - ceph: never send metrics if disable_send_metrics is set
+    - dm cache policy smq: ensure IO doesn't prevent cleaner policy progress
+    - rbd: make get_lock_owner_info() return a single locker or NULL
+    - rbd: harden get_lock_owner_info() a bit
+    - rbd: retrieve and check lock owner twice before blocklisting
+    - tracing: Fix trace_event_raw_event_synth() if else statement
+    - ACPI: processor: perflib: Use the "no limit" frequency QoS
+    - ACPI: processor: perflib: Avoid updating frequency QoS unnecessarily
+    - cpufreq: intel_pstate: Drop ACPI _PSS states table patching
+    - selftests: mptcp: sockopt: use 'iptables-legacy' if available
+    - io_uring: treat -EAGAIN for REQ_F_NOWAIT as final for io-wq
+    - ASoC: cs42l51: fix driver to properly autoload with automatic module loading
+    - selftests: mptcp: join: only check for ip6tables if needed
+    - Linux 5.15.124
+
+  * Jammy update: v5.15.123 upstream stable release (LP: #2034612)
+    - ALSA: hda/realtek - remove 3k pull low procedure
+    - ALSA: hda/realtek: Add quirk for Clevo NS70AU
+    - ALSA: hda/realtek: Enable Mute LED on HP Laptop 15s-eq2xxx
+    - keys: Fix linking a duplicate key to a keyring's assoc_array
+    - perf probe: Add test for regression introduced by switch to
+      die_get_decl_file()
+    - btrfs: fix warning when putting transaction with qgroups enabled after abort
+    - fuse: revalidate: don't invalidate if interrupted
+    - btrfs: zoned: fix memory leak after finding block group with super blocks
+    - fuse: ioctl: translate ENOSYS in outarg
+    - selftests: tc: set timeout to 15 minutes
+    - selftests: tc: add 'ct' action kconfig dep
+    - regmap: Drop initial version of maximum transfer length fixes
+    - regmap: Account for register length in SMBus I/O limits
+    - can: bcm: Fix UAF in bcm_proc_show()
+    - selftests: tc: add ConnTrack procfs kconfig
+    - drm/client: Fix memory leak in drm_client_target_cloned
+    - drm/client: Fix memory leak in drm_client_modeset_probe
+    - drm/amd/display: Disable MPC split by default on special asic
+    - drm/amd/display: Keep PHY active for DP displays on DCN31
+    - ASoC: fsl_sai: Disable bit clock with transmitter
+    - ASoC: codecs: wcd938x: fix missing clsh ctrl error handling
+    - ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix missing mbhc init error handling
+    - ASoC: codecs: wcd934x: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix codec initialisation race
+    - ASoC: codecs: wcd938x: fix soundwire initialisation race
+    - ext4: correct inline offset when handling xattrs in inode body
+    - drm/radeon: Fix integer overflow in radeon_cs_parser_init
+    - ALSA: emu10k1: roll up loops in DSP setup code for Audigy
+    - quota: Properly disable quotas when add_dquot_ref() fails
+    - quota: fix warning in dqgrab()
+    - udf: Fix uninitialized array access for some pathnames
+    - fs: jfs: Fix UBSAN: array-index-out-of-bounds in dbAllocDmapLev
+    - MIPS: dec: prom: Address -Warray-bounds warning
+    - FS: JFS: Fix null-ptr-deref Read in txBegin
+    - FS: JFS: Check for read-only mounted filesystem in txBegin
+    - spi: bcm63xx: fix max prepend length
+    - fbdev: imxfb: warn about invalid left/right margin
+    - perf build: Fix library not found error when using CSLIBS
+    - pinctrl: amd: Use amd_pinconf_set() for all config options
+    - net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()
+    - bridge: Add extack warning when enabling STP in netns.
+    - ethernet: use eth_hw_addr_set() instead of ether_addr_copy()
+    - of: net: add a helper for loading netdev->dev_addr
+    - ethernet: use of_get_ethdev_address()
+    - net: ethernet: mtk_eth_soc: handle probe deferral
+    - net: sched: cls_bpf: Undo tcf_bind_filter in case of an error
+    - iavf: Fix use-after-free in free_netdev
+    - iavf: Fix out-of-bounds when setting channels on remove
+    - security: keys: Modify mismatched function name
+    - octeontx2-pf: Dont allocate BPIDs for LBK interfaces
+    - bpf: Fix subprog idx logic in check_max_stack_depth
+    - igc: Prevent garbled TX queue with XDP ZEROCOPY
+    - tcp: annotate data-races around tcp_rsk(req)->ts_recent
+    - net: ipv4: Use kfree_sensitive instead of kfree
+    - net:ipv6: check return value of pskb_trim()
+    - Revert "tcp: avoid the lookup process failing to get sk in ehash table"
+    - fbdev: au1200fb: Fix missing IRQ check in au1200fb_drv_probe
+    - llc: Don't drop packet from non-root netns.
+    - netfilter: nf_tables: fix spurious set element insertion failure
+    - netfilter: nf_tables: skip bound chain in netns release path
+    - tcp: annotate data-races around tp->tcp_tx_delay
+    - tcp: annotate data-races around tp->keepalive_time
+    - tcp: annotate data-races around tp->keepalive_intvl
+    - tcp: annotate data-races around tp->keepalive_probes
+    - tcp: annotate data-races around icsk->icsk_syn_retries
+    - tcp: annotate data-races around tp->linger2
+    - tcp: annotate data-races around rskq_defer_accept
+    - tcp: annotate data-races around tp->notsent_lowat
+    - tcp: annotate data-races around icsk->icsk_user_timeout
+    - tcp: annotate data-races around fastopenq.max_qlen
+    - net: phy: prevent stale pointer dereference in phy_init()
+    - jbd2: recheck chechpointing non-dirty buffer
+    - tracing/histograms: Return an error if we fail to add histogram to hist_vars
+      list
+    - nixge: fix mac address error handling again
+    - Linux 5.15.123
+
+  * allow io_uring to be disabled in runtime (LP: #2035116)
+    - io_uring: add a sysctl to disable io_uring system-wide
+
+  * CVE-2023-31083
+    - Bluetooth: hci_ldisc: check HCI_UART_PROTO_READY flag in HCIUARTGETPROTO
+
+  * CVE-2023-3772
+    - xfrm: add NULL check in xfrm_update_ae_params
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Mon, 02 Oct 2023 15:40:31 +0200
+
+linux (5.15.0-86.96) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-86.96 -proposed tracker (LP: #2036575)
+
+  * 5.15.0-85 live migration regression (LP: #2036675)
+    - Revert "KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES"
+    - Revert "x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0"
+
+  * Regression for ubuntu_bpf test build on Jammy 5.15.0-85.95 (LP: #2035181)
+    - selftests/bpf: fix static assert compilation issue for test_cls_*.c
+
+  * `refcount_t: underflow; use-after-free.` on hidon w/ 5.15.0-85-generic
+    (LP: #2034447)
+    - crypto: rsa-pkcs1pad - Use helper to set reqsize
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 20 Sep 2023 09:32:27 +0200
+
+linux (5.15.0-85.95) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-85.95 -proposed tracker (LP: #2033821)
+
+  * Please enable Renesas RZ platform serial installer (LP: #2022361)
+    - [Config] enable hihope RZ/G2M serial console
+    - [Config] Mark sh-sci as built-in
+
+  * Request backport of xen timekeeping performance improvements (LP: #2033122)
+    - x86/xen/time: prefer tsc as clocksource when it is invariant
+
+  * kdump doesn't work with UEFI secure boot and kernel lockdown enabled on
+    ARM64 (LP: #2033007)
+    - [Config]: Enable CONFIG_KEXEC_IMAGE_VERIFY_SIG
+    - kexec, KEYS: make the code in bzImage64_verify_sig generic
+    - arm64: kexec_file: use more system keyrings to verify kernel image signature
+
+  * ubuntu_kernel_selftests:net:vrf-xfrm-tests.sh: 8 failed test cases on
+    jammy/fips (LP: #2019880)
+    - selftests: net: vrf-xfrm-tests: change authentication and encryption algos
+
+  * ubuntu_kernel_selftests:net:tls: 88 failed test cases on jammy/fips
+    (LP: #2019868)
+    - selftests/harness: allow tests to be skipped during setup
+    - selftests: net: tls: check if FIPS mode is enabled
+
+  * A general-proteciton exception during guest migration to unsupported PKRU
+    machine (LP: 2032164, reverted)
+    - x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0
+    - KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES
+
+  * CVE-2023-4569
+    - netfilter: nf_tables: deactivate catchall elements in next generation
+
+  * CVE-2023-20569
+    - x86/cpu, kvm: Add support for CPUID_80000021_EAX
+    - x86/srso: Add a Speculative RAS Overflow mitigation
+    - x86/srso: Add IBPB_BRTYPE support
+    - x86/srso: Add SRSO_NO support
+    - x86/srso: Add IBPB
+    - x86/srso: Add IBPB on VMEXIT
+    - x86/srso: Fix return thunks in generated code
+    - x86/srso: Tie SBPB bit setting to microcode patch detection
+    - x86: fix backwards merge of GDS/SRSO bit
+    - x86/srso: Fix build breakage with the LLVM linker
+    - x86/cpu: Fix __x86_return_thunk symbol type
+    - x86/cpu: Fix up srso_safe_ret() and __x86_return_thunk()
+    - x86/alternative: Make custom return thunk unconditional
+    - objtool: Add frame-pointer-specific function ignore
+    - x86/ibt: Add ANNOTATE_NOENDBR
+    - x86/cpu: Clean up SRSO return thunk mess
+    - x86/cpu: Rename original retbleed methods
+    - x86/cpu: Rename srso_(.*)_alias to srso_alias_\1
+    - x86/cpu: Cleanup the untrain mess
+    - x86/srso: Explain the untraining sequences a bit more
+    - x86/static_call: Fix __static_call_fixup()
+    - x86/retpoline: Don't clobber RFLAGS during srso_safe_ret()
+    - x86/srso: Disable the mitigation on unaffected configurations
+    - x86/retpoline,kprobes: Fix position of thunk sections with CONFIG_LTO_CLANG
+    - objtool/x86: Fixup frame-pointer vs rethunk
+    - x86/srso: Correct the mitigation status when SMT is disabled
+    - objtool/x86: Fix SRSO mess
+    - Ubuntu: [Config]: enable Speculative Return Stack Overflow mitigation
+
+  * Fix unreliable ethernet cable detection on I219 NIC (LP: #2028122)
+    - e1000e: Use PME poll to circumvent unreliable ACPI wake
+
+  * Need to get fine-grained control for FAN(TFN) Participant. (LP: #2031333)
+    - ACPI: fan: Separate file for attributes creation
+    - ACPI: fan: Optimize struct acpi_fan_fif
+    - ACPI: fan: Properly handle fine grain control
+    - ACPI: fan: Add additional attributes for fine grain control
+
+  * [SRU][Ubuntu 22.04.1] Unable to interpret the frequency values in
+    cpuinfo_min_freq and cpuino_max_freq sysfs files. (LP: #2030924)
+    - cpufreq: intel_pstate: Fix scaling for hybrid-capable
+
+  * CVE-2023-40283
+    - Bluetooth: L2CAP: Fix use-after-free in l2cap_sock_ready_cb
+
+  * CVE-2023-20588
+    - x86/bugs: Increase the x86 bugs vector size to two u32s
+    - x86/CPU/AMD: Do not leak quotient data after a division by 0
+    - x86/CPU/AMD: Fix the DIV(0) initial fix attempt
+
+  * CVE-2023-4194
+    - net: tun_chr_open(): set sk_uid from current_fsuid()
+    - net: tap_open(): set sk_uid from current_fsuid()
+
+  * CVE-2023-4155
+    - KVM: SEV: Refactor out sev_es_state struct
+    - KVM: SEV: Fall back to vmalloc for SEV-ES scratch area if necessary
+    - KVM: SVM: Do not terminate SEV-ES guests on GHCB validation failure
+    - KVM: SVM: Exit to userspace on ENOMEM/EFAULT GHCB errors
+    - KVM: SEV: snapshot the GHCB before accessing it
+    - KVM: SEV: only access GHCB fields once
+
+  * CVE-2023-1206
+    - tcp: Reduce chance of collisions in inet6_hashfn().
+
+  * Crashing with CPU soft lock on GA kernel 5.15.0.79.76 and HWE kernel
+    5.19.0-46.47-22.04.1 (LP: #2032176)
+    - Revert "KVM: x86: enable TDP MMU by default"
+
+  * Jammy update: v5.15.122 upstream stable release (LP: #2032690)
+    - Linux 5.15.122
+    - Upstream stable to v5.15.122
+
+  * Jammy update: v5.15.121 upstream stable release (LP: #2032689)
+    - netfilter: nf_tables: drop map element references from preparation phase
+    - fs: pipe: reveal missing function protoypes
+    - x86/resctrl: Only show tasks' pid in current pid namespace
+    - blk-iocost: use spin_lock_irqsave in adjust_inuse_and_calc_cost
+    - md/raid10: check slab-out-of-bounds in md_bitmap_get_counter
+    - md/raid10: fix overflow of md/safe_mode_delay
+    - md/raid10: fix wrong setting of max_corr_read_errors
+    - md/raid10: fix null-ptr-deref of mreplace in raid10_sync_request
+    - md/raid10: fix io loss while replacement replace rdev
+    - irqchip/jcore-aic: Fix missing allocation of IRQ descriptors
+    - svcrdma: Prevent page release when nothing was received
+    - posix-timers: Prevent RT livelock in itimer_delete()
+    - tracing/timer: Add missing hrtimer modes to decode_hrtimer_mode().
+    - clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe
+    - PM: domains: fix integer overflow issues in genpd_parse_state()
+    - perf/arm-cmn: Fix DTC reset
+    - powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
+    - ARM: 9303/1: kprobes: avoid missing-declaration warnings
+    - cpufreq: intel_pstate: Fix energy_performance_preference for passive
+    - thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()
+    - rcutorture: Correct name of use_softirq module parameter
+    - rcuscale: Always log error message
+    - rcuscale: Move shutdown from wait_event() to wait_event_idle()
+    - rcu/rcuscale: Move rcu_scale_*() after kfree_scale_cleanup()
+    - rcu/rcuscale: Stop kfree_scale_thread thread(s) after unloading rcuscale
+    - kselftest: vDSO: Fix accumulation of uninitialized ret when CLOCK_REALTIME
+      is undefined
+    - perf/ibs: Fix interface via core pmu events
+    - x86/mm: Fix __swp_entry_to_pte() for Xen PV guests
+    - locking/atomic: arm: fix sync ops
+    - evm: Complete description of evm_inode_setattr()
+    - evm: Fix build warnings
+    - ima: Fix build warnings
+    - pstore/ram: Add check for kstrdup
+    - igc: Enable and fix RX hash usage by netstack
+    - wifi: ath9k: fix AR9003 mac hardware hang check register offset calculation
+    - wifi: ath9k: avoid referencing uninit memory in ath9k_wmi_ctrl_rx
+    - libbpf: btf_dump_type_data_check_overflow needs to consider
+      BTF_MEMBER_BITFIELD_SIZE
+    - samples/bpf: Fix buffer overflow in tcp_basertt
+    - spi: spi-geni-qcom: Correct CS_TOGGLE bit in SPI_TRANS_CFG
+    - wifi: wilc1000: fix for absent RSN capabilities WFA testcase
+    - wifi: mwifiex: Fix the size of a memory allocation in
+      mwifiex_ret_802_11_scan()
+    - sctp: add bpf_bypass_getsockopt proto callback
+    - libbpf: fix offsetof() and container_of() to work with CO-RE
+    - bpf: Don't EFAULT for {g,s}setsockopt with wrong optlen
+    - spi: dw: Round of n_bytes to power of 2
+    - nfc: llcp: fix possible use of uninitialized variable in
+      nfc_llcp_send_connect()
+    - bpftool: JIT limited misreported as negative value on aarch64
+    - regulator: core: Fix more error checking for debugfs_create_dir()
+    - regulator: core: Streamline debugfs operations
+    - wifi: orinoco: Fix an error handling path in spectrum_cs_probe()
+    - wifi: orinoco: Fix an error handling path in orinoco_cs_probe()
+    - wifi: atmel: Fix an error handling path in atmel_probe()
+    - wl3501_cs: use eth_hw_addr_set()
+    - wifi: wl3501_cs: Fix an error handling path in wl3501_probe()
+    - wifi: ray_cs: Utilize strnlen() in parse_addr()
+    - wifi: ray_cs: Drop useless status variable in parse_addr()
+    - wifi: ray_cs: Fix an error handling path in ray_probe()
+    - wifi: ath9k: don't allow to overwrite ENDPOINT0 attributes
+    - selftests/bpf: Fix check_mtu using wrong variable type
+    - wifi: rsi: Do not configure WoWlan in shutdown hook if not enabled
+    - wifi: rsi: Do not set MMC_PM_KEEP_POWER in shutdown
+    - watchdog/perf: define dummy watchdog_update_hrtimer_threshold() on correct
+      config
+    - watchdog/perf: more properly prevent false positives with turbo modes
+    - kexec: fix a memory leak in crash_shrink_memory()
+    - memstick r592: make memstick_debug_get_tpc_name() static
+    - wifi: ath9k: Fix possible stall on ath9k_txq_list_has_key()
+    - rtnetlink: extend RTEXT_FILTER_SKIP_STATS to IFLA_VF_INFO
+    - wifi: iwlwifi: pull from TXQs with softirqs disabled
+    - iwlwifi: don't dump_stack() when we get an unexpected interrupt
+    - wifi: iwlwifi: pcie: fix NULL pointer dereference in
+      iwl_pcie_irq_rx_msix_handler()
+    - wifi: cfg80211: rewrite merging of inherited elements
+    - wifi: iwlwifi: mvm: indicate HW decrypt for beacon protection
+    - wifi: ath9k: convert msecs to jiffies where needed
+    - bpf: Omit superfluous address family check in __bpf_skc_lookup
+    - bpf: Factor out socket lookup functions for the TC hookpoint.
+    - bpf: Call __bpf_sk_lookup()/__bpf_skc_lookup() directly via TC hookpoint
+    - bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings
+    - can: length: fix bitstuffing count
+    - igc: Fix race condition in PTP tx code
+    - net: stmmac: fix double serdes powerdown
+    - netlink: fix potential deadlock in netlink_set_err()
+    - netlink: do not hard code device address lenth in fdb dumps
+    - bonding: do not assume skb mac_header is set
+    - selftests: rtnetlink: remove netdevsim device after ipsec offload test
+    - gtp: Fix use-after-free in __gtp_encap_destroy().
+    - net: axienet: Move reset before 64-bit DMA detection
+    - sfc: fix crash when reading stats while NIC is resetting
+    - lib/ts_bm: reset initial match offset for every block of text
+    - netfilter: conntrack: dccp: copy entire header to stack buffer, not just
+      basic one
+    - netfilter: nf_conntrack_sip: fix the ct_sip_parse_numerical_param() return
+      value.
+    - ipvlan: Fix return value of ipvlan_queue_xmit()
+    - netlink: Add __sock_i_ino() for __netlink_diag_dump().
+    - drm/amd/display: Add logging for display MALL refresh setting
+    - radeon: avoid double free in ci_dpm_init()
+    - drm/amd/display: Explicitly specify update type per plane info change
+    - Input: drv260x - sleep between polling GO bit
+    - drm/bridge: tc358768: always enable HS video mode
+    - drm/bridge: tc358768: fix PLL parameters computation
+    - drm/bridge: tc358768: fix PLL target frequency
+    - drm/bridge: tc358768: fix TCLK_ZEROCNT computation
+    - drm/bridge: tc358768: Add atomic_get_input_bus_fmts() implementation
+    - drm/bridge: tc358768: fix TCLK_TRAILCNT computation
+    - drm/bridge: tc358768: fix THS_ZEROCNT computation
+    - drm/bridge: tc358768: fix TXTAGOCNT computation
+    - drm/bridge: tc358768: fix THS_TRAILCNT computation
+    - drm/vram-helper: fix function names in vram helper doc
+    - ARM: dts: BCM5301X: Drop "clock-names" from the SPI node
+    - ARM: dts: meson8b: correct uart_B and uart_C clock references
+    - Input: adxl34x - do not hardcode interrupt trigger type
+    - drm: sun4i_tcon: use devm_clk_get_enabled in `sun4i_tcon_init_clocks`
+    - drm/panel: sharp-ls043t1le01: adjust mode settings
+    - ARM: dts: stm32: Move ethernet MAC EEPROM from SoM to carrier boards
+    - bus: ti-sysc: Fix dispc quirk masking bool variables
+    - arm64: dts: microchip: sparx5: do not use PSCI on reference boards
+    - clk: imx: scu: use _safe list iterator to avoid a use after free
+    - RDMA/bnxt_re: Disable/kill tasklet only if it is enabled
+    - RDMA/bnxt_re: Fix to remove unnecessary return labels
+    - RDMA/bnxt_re: Use unique names while registering interrupts
+    - RDMA/bnxt_re: Remove a redundant check inside bnxt_re_update_gid
+    - RDMA/bnxt_re: Fix to remove an unnecessary log
+    - drm/msm/dsi: don't allow enabling 14nm VCO with unprogrammed rate
+    - drm/msm/disp/dpu: get timing engine status from intf status register
+    - drm/msm/dpu: Set DPU_DATA_HCTL_EN for in INTF_SC7180_MASK
+    - ARM: dts: gta04: Move model property out of pinctrl node
+    - arm64: dts: qcom: msm8916: correct camss unit address
+    - arm64: dts: qcom: msm8994: correct SPMI unit address
+    - arm64: dts: qcom: msm8996: correct camss unit address
+    - arm64: dts: qcom: sdm630: correct camss unit address
+    - arm64: dts: qcom: sdm845: correct camss unit address
+    - arm64: dts: qcom: db820c: Move blsp1_uart2 pin states to msm8996.dtsi
+    - arm64: dts: qcom: apq8016-sbc: Update modem and WiFi firmware path
+    - arm64: dts: qcom: apq8016-sbc: Clarify firmware-names
+    - arm64: dts: qcom: apq8016-sbc: fix mpps state names
+    - arm64: dts: qcom: Drop unneeded extra device-specific includes
+    - arm64: dts: qcom: apq8016-sbc: Fix regulator constraints
+    - arm64: dts: qcom: apq8016-sbc: Fix 1.8V power rail on LS expansion
+    - drm/panel: simple: fix active size for Ampire AM-480272H3TMQW-T01H
+    - ARM: ep93xx: fix missing-prototype warnings
+    - ARM: omap2: fix missing tick_broadcast() prototype
+    - arm64: dts: qcom: apq8096: fix fixed regulator name property
+    - arm64: dts: mediatek: mt8183: Add mediatek,broken-save-restore-fw to kukui
+    - ARM: dts: stm32: Shorten the AV96 HDMI sound card name
+    - memory: brcmstb_dpfe: fix testing array offset after use
+    - ASoC: es8316: Increment max value for ALC Capture Target Volume control
+    - ASoC: es8316: Do not set rate constraints for unsupported MCLKs
+    - ARM: dts: meson8: correct uart_B and uart_C clock references
+    - soc/fsl/qe: fix usb.c build errors
+    - RDMA/irdma: avoid fortify-string warning in irdma_clr_wqes
+    - IB/hfi1: Use bitmap_zalloc() when applicable
+    - IB/hfi1: Fix wrong mmu_node used for user SDMA packet after invalidate
+    - RDMA/hns: Fix hns_roce_table_get return value
+    - ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier
+    - arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1
+    - fbdev: omapfb: lcd_mipid: Fix an error handling path in mipid_spi_probe()
+    - arm64: dts: ti: k3-j7200: Fix physical address of pin
+    - ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2
+    - ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx
+    - hwmon: (gsc-hwmon) fix fan pwm temperature scaling
+    - hwmon: (adm1275) Allow setting sample averaging
+    - hwmon: (pmbus/adm1275) Fix problems with temperature monitoring on ADM1272
+    - ARM: dts: BCM5301X: fix duplex-full => full-duplex
+    - drm/amdkfd: Fix potential deallocation of previously deallocated memory.
+    - drm/amd/display: Fix artifacting on eDP panels when engaging freesync video
+      mode
+    - drm/radeon: fix possible division-by-zero errors
+    - amdgpu: validate offset_in_bo of drm_amdgpu_gem_va
+    - drm/msm/a5xx: really check for A510 in a5xx_gpu_init
+    - RDMA/bnxt_re: wraparound mbox producer index
+    - RDMA/bnxt_re: Avoid calling wake_up threads from spin_lock context
+    - clk: imx: clk-imx8mn: fix memory leak in imx8mn_clocks_probe
+    - clk: imx: clk-imx8mp: improve error handling in imx8mp_clocks_probe()
+    - arm64: dts: qcom: sm8250-edo: Panel framebuffer is 2.5k instead of 4k
+    - clk: clocking-wizard: Fix Oops in clk_wzrd_register_divider()
+    - clk: tegra: tegra124-emc: Fix potential memory leak
+    - ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer
+    - drm/msm/dpu: do not enable color-management if DSPPs are not available
+    - drm/msm/dp: Free resources after unregistering them
+    - arm64: dts: mediatek: Add cpufreq nodes for MT8192
+    - arm64: dts: mediatek: mt8192: Fix CPUs capacity-dmips-mhz
+    - drm/msm/dpu: correct MERGE_3D length
+    - clk: vc5: check memory returned by kasprintf()
+    - clk: cdce925: check return value of kasprintf()
+    - clk: si5341: return error if one synth clock registration fails
+    - clk: si5341: check return value of {devm_}kasprintf()
+    - clk: si5341: free unused memory on probe failure
+    - clk: keystone: sci-clk: check return value of kasprintf()
+    - clk: ti: clkctrl: check return value of kasprintf()
+    - drivers: meson: secure-pwrc: always enable DMA domain
+    - ovl: update of dentry revalidate flags after copy up
+    - ASoC: imx-audmix: check return value of devm_kasprintf()
+    - clk: Fix memory leak in devm_clk_notifier_register()
+    - PCI: cadence: Fix Gen2 Link Retraining process
+    - PCI: vmd: Reset VMD config register between soft reboots
+    - scsi: qedf: Fix NULL dereference in error handling
+    - pinctrl: bcm2835: Handle gpiochip_add_pin_range() errors
+    - PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free
+    - scsi: 3w-xxxx: Add error handling for initialization failure in tw_probe()
+    - PCI: pciehp: Cancel bringup sequence if card is not present
+    - PCI: ftpci100: Release the clock resources
+    - PCI: Add pci_clear_master() stub for non-CONFIG_PCI
+    - perf bench: Use unbuffered output when pipe/tee'ing to a file
+    - perf bench: Add missing setlocale() call to allow usage of %'d style
+      formatting
+    - pinctrl: cherryview: Return correct value if pin in push-pull mode
+    - kcsan: Don't expect 64 bits atomic builtins from 32 bits architectures
+    - powerpc/interrupt: Don't read MSR from interrupt_exit_kernel_prepare()
+    - powerpc/signal32: Force inlining of __unsafe_save_user_regs() and
+      save_tm_user_regs_unsafe()
+    - perf script: Fix allocation of evsel->priv related to per-event dump files
+    - perf dwarf-aux: Fix off-by-one in die_get_varname()
+    - powerpc/64s: Fix VAS mm use after free
+    - pinctrl: microchip-sgpio: check return value of devm_kasprintf()
+    - pinctrl: at91-pio4: check return value of devm_kasprintf()
+    - powerpc/powernv/sriov: perform null check on iov before dereferencing iov
+    - powerpc: simplify ppc_save_regs
+    - powerpc: update ppc_save_regs to save current r1 in pt_regs
+    - riscv: uprobes: Restore thread.bad_cause
+    - powerpc/book3s64/mm: Fix DirectMap stats in /proc/meminfo
+    - powerpc/mm/dax: Fix the condition when checking if altmap vmemap can cross-
+      boundary
+    - hwrng: virtio - add an internal buffer
+    - hwrng: virtio - don't wait on cleanup
+    - hwrng: virtio - don't waste entropy
+    - hwrng: virtio - always add a pending request
+    - hwrng: virtio - Fix race on data_avail and actual data
+    - modpost: remove broken calculation of exception_table_entry size
+    - crypto: nx - fix build warnings when DEBUG_FS is not enabled
+    - modpost: fix section mismatch message for R_ARM_ABS32
+    - modpost: fix section mismatch message for R_ARM_{PC24,CALL,JUMP24}
+    - crypto: marvell/cesa - Fix type mismatch warning
+    - modpost: fix off by one in is_executable_section()
+    - ARC: define ASM_NL and __ALIGN(_STR) outside #ifdef __ASSEMBLY__ guard
+    - crypto: qat - honor CRYPTO_TFM_REQ_MAY_SLEEP flag
+    - crypto: qat - replace get_current_node() with numa_node_id()
+    - crypto: qat - use reference to structure in dma_map_single()
+    - crypto: kpp - Add helper to set reqsize
+    - crypto: qat - Use helper to set reqsize
+    - crypto: qat - unmap buffer before free for DH
+    - crypto: qat - unmap buffers before free for RSA
+    - NFSv4.1: freeze the session table upon receiving NFS4ERR_BADSESSION
+    - SMB3: Do not send lease break acknowledgment if all file handles have been
+      closed
+    - dax: Fix dax_mapping_release() use after free
+    - dax: Introduce alloc_dev_dax_id()
+    - dax/kmem: Pass valid argument to memory_group_register_static
+    - hwrng: st - keep clock enabled while hwrng is registered
+    - kbuild: Disable GCOV for *.mod.o
+    - efi/libstub: Disable PCI DMA before grabbing the EFI memory map
+    - ksmbd: avoid field overflow warning
+    - ACPI: utils: Fix acpi_evaluate_dsm_typed() redefinition error
+    - bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
+    - USB: serial: option: add LARA-R6 01B PIDs
+    - usb: dwc3: gadget: Propagate core init errors to UDC during pullup
+    - phy: tegra: xusb: Clear the driver reference in usb-phy dev
+    - iio: adc: ad7192: Fix null ad7192_state pointer access
+    - iio: adc: ad7192: Fix internal/external clock selection
+    - iio: accel: fxls8962af: errata bug only applicable for FXLS8962AF
+    - iio: accel: fxls8962af: fixup buffer scan element type
+    - ALSA: hda/realtek: Add quirk for Clevo NPx0SNx
+    - ALSA: jack: Fix mutex call in snd_jack_report()
+    - block: fix signed int overflow in Amiga partition support
+    - block: add overflow checks for Amiga partition support
+    - block: change all __u32 annotations to __be32 in affs_hardblocks.h
+    - block: increment diskseq on all media change events
+    - SUNRPC: Fix UAF in svc_tcp_listen_data_ready()
+    - w1: w1_therm: fix locking behavior in convert_t
+    - w1: fix loop in w1_fini()
+    - sh: j2: Use ioremap() to translate device tree address into kernel memory
+    - usb: dwc2: platform: Improve error reporting for problems during .remove()
+    - usb: dwc2: Fix some error handling paths
+    - serial: 8250: omap: Fix freeing of resources on failed register
+    - clk: qcom: camcc-sc7180: Add parent dependency to all camera GDSCs
+    - clk: qcom: gcc-ipq6018: Use floor ops for sdcc clocks
+    - media: usb: Check az6007_read() return value
+    - media: videodev2.h: Fix struct v4l2_input tuner index comment
+    - media: usb: siano: Fix warning due to null work_func_t function pointer
+    - media: i2c: Correct format propagation for st-mipid02
+    - clk: qcom: reset: Allow specifying custom reset delay
+    - clk: qcom: reset: support resetting multiple bits
+    - clk: qcom: ipq6018: fix networking resets
+    - usb: dwc3: qcom: Fix potential memory leak
+    - usb: gadget: u_serial: Add null pointer check in gserial_suspend
+    - extcon: Fix kernel doc of property fields to avoid warnings
+    - extcon: Fix kernel doc of property capability fields to avoid warnings
+    - usb: phy: phy-tahvo: fix memory leak in tahvo_usb_probe()
+    - usb: hide unused usbfs_notify_suspend/resume functions
+    - serial: 8250: lock port for stop_rx() in omap8250_irq()
+    - serial: 8250: lock port for UART_IER access in omap8250_irq()
+    - kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
+    - coresight: Fix loss of connection info when a module is unloaded
+    - mfd: rt5033: Drop rt5033-battery sub-device
+    - media: venus: helpers: Fix ALIGN() of non power of two
+    - media: atomisp: gmin_platform: fix out_len in gmin_get_config_dsm_var()
+    - KVM: s390: fix KVM_S390_GET_CMMA_BITS for GFNs in memslot holes
+    - usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()
+    - usb: dwc3: qcom: Fix an error handling path in dwc3_qcom_probe()
+    - usb: common: usb-conn-gpio: Set last role to unknown before initial
+      detection
+    - usb: dwc3-meson-g12a: Fix an error handling path in dwc3_meson_g12a_probe()
+    - mfd: intel-lpss: Add missing check for platform_get_resource
+    - Revert "usb: common: usb-conn-gpio: Set last role to unknown before initial
+      detection"
+    - serial: 8250_omap: Use force_suspend and resume for system suspend
+    - test_firmware: return ENOMEM instead of ENOSPC on failed memory allocation
+    - nvmem: rmem: Use NVMEM_DEVID_AUTO
+    - mfd: stmfx: Fix error path in stmfx_chip_init
+    - mfd: stmfx: Nullify stmfx->vdd in case of error
+    - KVM: s390: vsie: fix the length of APCB bitmap
+    - KVM: s390/diag: fix racy access of physical cpu number in diag 9c handler
+    - mfd: stmpe: Only disable the regulators if they are enabled
+    - phy: tegra: xusb: check return value of devm_kzalloc()
+    - pwm: imx-tpm: force 'real_period' to be zero in suspend
+    - pwm: sysfs: Do not apply state to already disabled PWMs
+    - pwm: ab8500: Fix error code in probe()
+    - pwm: mtk_disp: Fix the disable flow of disp_pwm
+    - md/raid10: fix the condition to call bio_end_io_acct()
+    - rtc: st-lpc: Release some resources in st_rtc_probe() in case of error
+    - drm/i915/psr: Use hw.adjusted mode when calculating io/fast wake times
+    - media: cec: i2c: ch7322: also select REGMAP
+    - sctp: fix potential deadlock on &net->sctp.addr_wq_lock
+    - net/sched: act_ipt: add sanity checks on table name and hook locations
+    - Add MODULE_FIRMWARE() for FIRMWARE_TG357766.
+    - ibmvnic: Do not reset dql stats on NON_FATAL err
+    - net: dsa: vsc73xx: fix MTU configuration
+    - spi: bcm-qspi: return error if neither hif_mspi nor mspi is available
+    - mailbox: ti-msgmgr: Fill non-message tx data fields with 0x0
+    - f2fs: fix error path handling in truncate_dnode()
+    - octeontx2-af: Fix mapping for NIX block from CGX connection
+    - octeontx2-af: Add validation before accessing cgx and lmac
+    - ntfs: Fix panic about slab-out-of-bounds caused by ntfs_listxattr()
+    - powerpc: allow PPC_EARLY_DEBUG_CPM only when SERIAL_CPM=y
+    - net: bridge: keep ports without IFF_UNICAST_FLT in BR_PROMISC mode
+    - tcp: annotate data races in __tcp_oow_rate_limited()
+    - xsk: Honor SO_BINDTODEVICE on bind
+    - net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
+    - riscv: move memblock_allow_resize() after linear mapping is ready
+    - pptp: Fix fib lookup calls.
+    - net: dsa: tag_sja1105: fix MAC DA patching from meta frames
+    - octeontx-af: fix hardware timestamp configuration
+    - s390/qeth: Fix vipa deletion
+    - sh: dma: Fix DMA channel offset calculation
+    - apparmor: fix missing error check for rhashtable_insert_fast
+    - i2c: xiic: Defer xiic_wakeup() and __xiic_start_xfer() in xiic_process()
+    - i2c: xiic: Don't try to handle more interrupt events after error
+    - extcon: usbc-tusb320: Convert to i2c's .probe_new()
+    - btrfs: do not BUG_ON() on tree mod log failure at balance_level()
+    - i2c: qup: Add missing unwind goto in qup_i2c_probe()
+    - NFSD: add encoding of op_recall flag for write delegation
+    - io_uring: wait interruptibly for request completions on exit
+    - mmc: core: disable TRIM on Kingston EMMC04G-M627
+    - mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M
+    - mmc: mmci: Set PROBE_PREFER_ASYNCHRONOUS
+    - mmc: sdhci: fix DMA configure compatibility issue when 64bit DMA mode is
+      used.
+    - bcache: fixup btree_cache_wait list damage
+    - bcache: Remove unnecessary NULL point check in node allocations
+    - bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent
+    - um: Use HOST_DIR for mrproper
+    - integrity: Fix possible multiple allocation in integrity_inode_get()
+    - autofs: use flexible array in ioctl structure
+    - shmem: use ramfs_kill_sb() for kill_sb method of ramfs-based tmpfs
+    - ext4: Remove ext4 locking of moved directory
+    - Revert "f2fs: fix potential corruption when moving a directory"
+    - fs: Establish locking order for unrelated directories
+    - fs: Lock moved directories
+    - ipvs: increase ip_vs_conn_tab_bits range for 64BIT
+    - jffs2: reduce stack usage in jffs2_build_xattr_subsystem()
+    - fs: avoid empty option when generating legacy mount string
+    - btrfs: add handling for RAID1C23/DUP to btrfs_reduce_alloc_profile
+    - btrfs: delete unused BGs while reclaiming BGs
+    - btrfs: bail out reclaim process if filesystem is read-only
+    - btrfs: reinsert BGs failed to reclaim
+    - btrfs: fix race when deleting quota root from the dirty cow roots list
+    - btrfs: fix extent buffer leak after tree mod log failure at split_node()
+    - btrfs: do not BUG_ON() on tree mod log failure at __btrfs_cow_block()
+    - ASoC: mediatek: mt8173: Fix irq error path
+    - ASoC: mediatek: mt8173: Fix snd_soc_component_initialize error path
+    - ARM: dts: qcom: ipq4019: fix broken NAND controller properties override
+    - ARM: orion5x: fix d2net gpio initialization
+    - leds: trigger: netdev: Recheck NETDEV_LED_MODE_LINKUP on dev rename
+    - fs: no need to check source
+    - ovl: fix null pointer dereference in ovl_get_acl_rcu()
+    - fanotify: disallow mount/sb marks on kernel internal pseudo fs
+    - netfilter: conntrack: Avoid nf_ct_helper_hash uses after free
+    - wireguard: queueing: use saner cpu selection wrapping
+    - wireguard: netlink: send staged packets when setting initial private key
+    - tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
+    - block/partition: fix signedness issue for Amiga partitions
+    - io_uring: Use io_schedule* in cqring wait
+    - io_uring: add reschedule point to handle_tw_list()
+    - net: lan743x: Don't sleep in atomic context
+    - workqueue: clean up WORK_* constant types, clarify masking
+    - ksmbd: use ksmbd_req_buf_next() in ksmbd_smb2_check_message()
+    - ksmbd: validate command payload size
+    - ksmbd: fix out-of-bound read in smb2_write
+    - ksmbd: validate session id and tree id in the compound request
+    - drm/panel: simple: Add connector_type for innolux_at043tn24
+    - drm/bridge: ti-sn65dsi86: Fix auxiliary bus lifetime
+    - drm/panel: simple: Add Powertip PH800480T013 drm_display_mode flags
+    - igc: Remove delay during TX ring configuration
+    - net/mlx5e: fix double free in mlx5e_destroy_flow_table
+    - net/mlx5e: fix memory leak in mlx5e_ptp_open
+    - net/mlx5e: Check for NOT_READY flag state after locking
+    - igc: set TP bit in 'supported' and 'advertising' fields of
+      ethtool_link_ksettings
+    - igc: Handle PPS start time programming for past time values
+    - scsi: qla2xxx: Fix error code in qla2x00_start_sp()
+    - bpf: Fix max stack depth check for async callbacks
+    - net: mvneta: fix txq_map in case of txq_number==1
+    - gve: Set default duplex configuration to full
+    - ionic: remove WARN_ON to prevent panic_on_warn
+    - net: bgmac: postpone turning IRQs off to avoid SoC hangs
+    - net: prevent skb corruption on frag list segmentation
+    - icmp6: Fix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev().
+    - udp6: fix udp6_ehashfn() typo
+    - ntb: idt: Fix error handling in idt_pci_driver_init()
+    - NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
+    - ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
+    - NTB: ntb_transport: fix possible memory leak while device_register() fails
+    - NTB: ntb_tool: Add check for devm_kcalloc
+    - ipv6/addrconf: fix a potential refcount underflow for idev
+    - platform/x86: wmi: remove unnecessary argument
+    - platform/x86: wmi: use guid_t and guid_equal()
+    - platform/x86: wmi: move variables
+    - platform/x86: wmi: Break possible infinite loop when parsing GUID
+    - kernel/trace: Fix cleanup logic of enable_trace_eprobe
+    - igc: Fix launchtime before start of cycle
+    - igc: Fix inserting of empty frame for launchtime
+    - bpf, riscv: Support riscv jit to provide bpf_line_info
+    - riscv, bpf: Fix inconsistent JIT image generation
+    - drm/i915: Fix one wrong caching mode enum usage
+    - octeontx2-pf: Add additional check for MCAM rules
+    - erofs: avoid infinite loop in z_erofs_do_read_page() when reading beyond EOF
+    - erofs: decouple basic mount options from fs_context
+    - erofs: fix fsdax unavailability for chunk-based regular files
+    - wifi: airo: avoid uninitialized warning in airo_get_rate()
+    - bpf: cpumap: Fix memory leak in cpu_map_update_elem
+    - net/sched: flower: Ensure both minimum and maximum ports are specified
+    - riscv: mm: fix truncation warning on RV32
+    - netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()
+    - net/sched: make psched_mtu() RTNL-less safe
+    - nvme-pci: remove nvme_queue from nvme_iod
+    - nvme-pci: fix DMA direction of unmapping integrity data
+    - pinctrl: amd: Fix mistake in handling clearing pins at startup
+    - pinctrl: amd: Detect internal GPIO0 debounce handling
+    - pinctrl: amd: Detect and mask spurious interrupts
+    - pinctrl: amd: Only use special debounce behavior for GPIO 0
+    - tpm: tpm_vtpm_proxy: fix a race condition in /dev/vtpmx creation
+    - mtd: rawnand: meson: fix unaligned DMA buffers handling
+    - net: bcmgenet: Ensure MDIO unregistration has clocks enabled
+    - mm/damon/ops-common: atomically test and clear young on ptes and pmds
+    - powerpc: Fail build if using recordmcount with binutils v2.37
+    - misc: fastrpc: Create fastrpc scalar with correct buffer count
+    - powerpc/security: Fix Speculation_Store_Bypass reporting on Power10
+    - arm64: errata: Add detection for TRBE overwrite in FILL mode
+    - erofs: fix compact 4B support for 16k block size
+    - MIPS: Loongson: Fix cpu_probe_loongson() again
+    - MIPS: KVM: Fix NULL pointer dereference
+    - ext4: Fix reusing stale buffer heads from last failed mounting
+    - ext4: fix wrong unit use in ext4_mb_clear_bb
+    - ext4: get block from bh in ext4_free_blocks for fast commit replay
+    - ext4: fix wrong unit use in ext4_mb_new_blocks
+    - ext4: fix to check return value of freeze_bdev() in ext4_shutdown()
+    - ext4: turn quotas off if mount failed after enabling quotas
+    - ext4: only update i_reserved_data_blocks on successful block allocation
+    - jfs: jfs_dmap: Validate db_l2nbperpage while mounting
+    - hwrng: imx-rngc - fix the timeout for init and self check
+    - dm integrity: reduce vmalloc space footprint on 32-bit architectures
+    - PCI/PM: Avoid putting EloPOS E2/S2/H2 PCIe Ports in D3cold
+    - PCI: Add function 1 DMA alias quirk for Marvell 88SE9235
+    - PCI: qcom: Disable write access to read only registers for IP v2.3.3
+    - PCI: rockchip: Assert PCI Configuration Enable bit after probe
+    - PCI: rockchip: Write PCI Device ID to correct register
+    - PCI: rockchip: Add poll and timeout to wait for PHY PLLs to be locked
+    - PCI: rockchip: Fix legacy IRQ generation for RK3399 PCIe endpoint core
+    - PCI: rockchip: Use u32 variable to access 32-bit registers
+    - PCI: rockchip: Set address alignment for endpoint mode
+    - misc: pci_endpoint_test: Free IRQs before removing the device
+    - misc: pci_endpoint_test: Re-init completion for every test
+    - mfd: pm8008: Fix module autoloading
+    - md/raid0: add discard support for the 'original' layout
+    - dm init: add dm-mod.waitfor to wait for asynchronously probed block devices
+    - fs: dlm: return positive pid value for F_GETLK
+    - drm/atomic: Allow vblank-enabled + self-refresh "disable"
+    - drm/rockchip: vop: Leave vblank enabled in self-refresh
+    - drm/amdgpu: fix clearing mappings for BOs that are always valid in VM
+    - drm/amd/display: Correct `DMUB_FW_VERSION` macro
+    - drm/amdgpu: avoid restore process run into dead loop.
+    - drm/ttm: Don't leak a resource on swapout move error
+    - serial: atmel: don't enable IRQs prematurely
+    - tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in
+      case of error
+    - tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when
+      iterating clk
+    - tty: serial: imx: fix rs485 rx after tx
+    - firmware: stratix10-svc: Fix a potential resource leak in
+      svc_create_memory_pool()
+    - libceph: harden msgr2.1 frame segment length checks
+    - ceph: don't let check_caps skip sending responses for revoke msgs
+    - xhci: Fix resume issue of some ZHAOXIN hosts
+    - xhci: Fix TRB prefetch issue of ZHAOXIN hosts
+    - xhci: Show ZHAOXIN xHCI root hub speed correctly
+    - meson saradc: fix clock divider mask length
+    - opp: Fix use-after-free in lazy_opp_tables after probe deferral
+    - soundwire: qcom: fix storing port config out-of-bounds
+    - Revert "8250: add support for ASIX devices with a FIFO bug"
+    - bus: ixp4xx: fix IXP4XX_EXP_T1_MASK
+    - s390/decompressor: fix misaligned symbol build error
+    - tracing/histograms: Add histograms to hist_vars if they have referenced
+      variables
+    - tracing: Fix memory leak of iter->temp when reading trace_pipe
+    - samples: ftrace: Save required argument registers in sample trampolines
+    - net: ena: fix shift-out-of-bounds in exponential backoff
+    - ring-buffer: Fix deadloop issue on reading trace_pipe
+    - ftrace: Fix possible warning on checking all pages used in
+      ftrace_process_locs()
+    - xtensa: ISS: fix call to split_if_spec
+    - tracing: Fix null pointer dereference in tracing_err_log_open()
+    - selftests: mptcp: sockopt: return error if wrong mark
+    - selftests: mptcp: depend on SYN_COOKIES
+    - tracing/probes: Fix not to count error code to total length
+    - tracing/probes: Fix to update dynamic data counter if fetcharg uses it
+    - scsi: qla2xxx: Wait for io return on terminate rport
+    - scsi: qla2xxx: Array index may go out of bound
+    - scsi: qla2xxx: Avoid fcport pointer dereference
+    - scsi: qla2xxx: Fix buffer overrun
+    - scsi: qla2xxx: Fix potential NULL pointer dereference
+    - scsi: qla2xxx: Check valid rport returned by fc_bsg_to_rport()
+    - scsi: qla2xxx: Correct the index of array
+    - scsi: qla2xxx: Pointer may be dereferenced
+    - scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue
+    - MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
+    - net/sched: sch_qfq: reintroduce lmax bound check for MTU
+    - drm/atomic: Fix potential use-after-free in nonblocking commits
+    - Linux 5.15.121
+
+  * Jammy update: v5.15.120 upstream stable release (LP: #2032688)
+    - mptcp: fix possible divide by zero in recvmsg()
+    - mptcp: consolidate fallback and non fallback state machine
+    - mm, hwpoison: try to recover from copy-on write faults
+    - mm, hwpoison: when copy-on-write hits poison, take page offline
+    - drm/amdgpu: Set vmbo destroy after pt bo is created
+    - x86/microcode/AMD: Load late on both threads too
+    - x86/smp: Use dedicated cache-line for mwait_play_dead()
+    - can: isotp: isotp_sendmsg(): fix return error fix on TX path
+    - bpf: ensure main program has an extable
+    - HID: wacom: Use ktime_t rather than int when dealing with timestamps
+    - HID: logitech-hidpp: add HIDPP_QUIRK_DELAYED_INIT for the T651.
+    - Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak
+      in mtk_thermal_probe"
+    - perf symbols: Symbol lookup with kcore can fail if multiple segments match
+      stext
+    - scripts/tags.sh: Resolve gtags empty index generation
+    - drm/amdgpu: Validate VM ioctl flags.
+    - parisc: Delete redundant register definitions in <asm/assembly.h>
+    - nubus: Partially revert proc_create_single_data() conversion
+    - Linux 5.15.120
+
+  * Jammy update: v5.15.119 upstream stable release (LP: #2032683)
+    - drm/amd/display: fix the system hang while disable PSR
+    - tracing: Add tracing_reset_all_online_cpus_unlocked() function
+    - tpm, tpm_tis: Claim locality in interrupt handler
+    - drm/amd/display: Add minimal pipe split transition state
+    - drm/amd/display: Use dc_update_planes_and_stream
+    - drm/amd/display: Add wrapper to call planes and stream update
+    - tick/common: Align tick period during sched_timer setup
+    - selftests: mptcp: lib: skip if missing symbol
+    - selftests: mptcp: lib: skip if not below kernel version
+    - selftests/mount_setattr: fix redefine struct mount_attr build error
+    - selftests: mptcp: pm nl: remove hardcoded default limits
+    - selftests: mptcp: join: use 'iptables-legacy' if available
+    - selftests: mptcp: join: skip check if MIB counter not supported
+    - nilfs2: fix buffer corruption due to concurrent device reads
+    - ACPI: sleep: Avoid breaking S3 wakeup due to might_sleep()
+    - KVM: Avoid illegal stage2 mapping on invalid memory slot
+    - Drivers: hv: vmbus: Call hv_synic_free() if hv_synic_alloc() fails
+    - Drivers: hv: vmbus: Fix vmbus_wait_for_unload() to scan present CPUs
+    - PCI: hv: Fix a race condition bug in hv_pci_query_relations()
+    - Revert "PCI: hv: Fix a timing issue which causes kdump to fail occasionally"
+    - PCI: hv: Remove the useless hv_pcichild_state from struct hv_pci_dev
+    - PCI: hv: Fix a race condition in hv_irq_unmask() that can cause panic
+    - PCI: hv: Add a per-bus mutex state_lock
+    - cgroup: Do not corrupt task iteration when rebinding subsystem
+    - mmc: sdhci-msm: Disable broken 64-bit DMA on MSM8916
+    - mmc: meson-gx: remove redundant mmc_request_done() call from irq context
+    - mmc: mmci: stm32: fix max busy timeout calculation
+    - ip_tunnels: allow VXLAN/GENEVE to inherit TOS/TTL from VLAN
+    - regulator: pca9450: Fix LDO3OUT and LDO4OUT MASK
+    - regmap: spi-avmm: Fix regmap_bus max_raw_write
+    - writeback: fix dereferencing NULL mapping->host on writeback_page_template
+    - io_uring/net: save msghdr->msg_control for retries
+    - io_uring/net: clear msg_controllen on partial sendmsg retry
+    - io_uring/net: disable partial retries for recvmsg with cmsg
+    - nilfs2: prevent general protection fault in nilfs_clear_dirty_page()
+    - x86/mm: Avoid using set_pgd() outside of real PGD pages
+    - memfd: check for non-NULL file_seals in memfd_create() syscall
+    - mmc: meson-gx: fix deferred probing
+    - ieee802154: hwsim: Fix possible memory leaks
+    - xfrm: Treat already-verified secpath entries as optional
+    - xfrm: interface: rename xfrm_interface.c to xfrm_interface_core.c
+    - xfrm: Ensure policies always checked on XFRM-I input path
+    - bpf: track immediate values written to stack by BPF_ST instruction
+    - bpf: Fix verifier id tracking of scalars on spill
+    - xfrm: fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
+    - selftests: net: fcnal-test: check if FIPS mode is enabled
+    - xfrm: Linearize the skb after offloading if needed.
+    - net: qca_spi: Avoid high load if QCA7000 is not available
+    - mmc: mtk-sd: fix deferred probing
+    - mmc: mvsdio: fix deferred probing
+    - mmc: omap: fix deferred probing
+    - mmc: omap_hsmmc: fix deferred probing
+    - mmc: owl: fix deferred probing
+    - mmc: sdhci-acpi: fix deferred probing
+    - mmc: sh_mmcif: fix deferred probing
+    - mmc: usdhi60rol0: fix deferred probing
+    - ipvs: align inner_mac_header for encapsulation
+    - net: dsa: mt7530: fix trapping frames on non-MT7621 SoC MT7530 switch
+    - net: dsa: mt7530: fix handling of BPDUs on MT7530 switch
+    - be2net: Extend xmit workaround to BE3 chip
+    - netfilter: nft_set_pipapo: .walk does not deal with generations
+    - netfilter: nf_tables: disallow element updates of bound anonymous sets
+    - netfilter: nf_tables: reject unbound anonymous set before commit phase
+    - netfilter: nf_tables: reject unbound chain set before commit phase
+    - netfilter: nf_tables: disallow updates of anonymous sets
+    - netfilter: nfnetlink_osf: fix module autoload
+    - Revert "net: phy: dp83867: perform soft reset and retain established link"
+    - bpf/btf: Accept function names that contain dots
+    - selftests: forwarding: Fix race condition in mirror installation
+    - sch_netem: acquire qdisc lock in netem_change()
+    - gpio: Allow per-parent interrupt data
+    - gpiolib: Fix GPIO chip IRQ initialization restriction
+    - gpio: sifive: add missing check for platform_get_irq
+    - scsi: target: iscsi: Prevent login threads from racing between each other
+    - HID: wacom: Add error check to wacom_parse_and_register()
+    - arm64: Add missing Set/Way CMO encodings
+    - media: cec: core: don't set last_initiator if tx in progress
+    - nfcsim.c: Fix error checking for debugfs_create_dir
+    - usb: gadget: udc: fix NULL dereference in remove()
+    - nvme: double KA polling frequency to avoid KATO with TBKAS on
+    - Input: soc_button_array - add invalid acpi_index DMI quirk handling
+    - s390/cio: unregister device when the only path is gone
+    - spi: lpspi: disable lpspi module irq in DMA mode
+    - ASoC: simple-card: Add missing of_node_put() in case of error
+    - soundwire: dmi-quirks: add new mapping for HP Spectre x360
+    - ASoC: nau8824: Add quirk to active-high jack-detect
+    - s390/purgatory: disable branch profiling
+    - ARM: dts: Fix erroneous ADS touchscreen polarities
+    - drm/exynos: vidi: fix a wrong error return
+    - drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl
+    - drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl
+    - vhost_net: revert upend_idx only on retriable error
+    - x86/apic: Fix kernel panic when booting with intremap=off and x2apic_phys
+    - i2c: imx-lpi2c: fix type char overflow issue when calculating the clock
+      cycle
+    - act_mirred: remove unneded merge conflict markers
+    - Linux 5.15.119
+
+  * Jammy update: v5.15.118 upstream stable release (LP: #2030239)
+    - test_firmware: Use kstrtobool() instead of strtobool()
+    - test_firmware: prevent race conditions by a correct implementation of
+      locking
+    - test_firmware: fix a memory leak with reqs buffer
+    - ksmbd: fix slab-out-of-bounds read in smb2_handle_negotiate
+    - drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram
+    - of: overlay: rename variables to be consistent
+    - of: overlay: rework overlay apply and remove kfree()s
+    - of: overlay: Fix missing of_node_put() in error case of
+      init_overlay_changeset()
+    - power: supply: ab8500: Fix external_power_changed race
+    - power: supply: sc27xx: Fix external_power_changed race
+    - power: supply: bq27xxx: Use mod_delayed_work() instead of cancel() +
+      schedule()
+    - ARM: dts: vexpress: add missing cache properties
+    - tools: gpio: fix debounce_period_us output of lsgpio
+    - power: supply: Ratelimit no data debug output
+    - platform/x86: asus-wmi: Ignore WMI events with codes 0x7B, 0xC0
+    - regulator: Fix error checking for debugfs_create_dir
+    - irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issues
+    - power: supply: Fix logic checking if system is running from battery
+    - btrfs: scrub: try harder to mark RAID56 block groups read-only
+    - btrfs: handle memory allocation failure in btrfs_csum_one_bio
+    - ASoC: soc-pcm: test if a BE can be prepared
+    - parisc: Improve cache flushing for PCXL in arch_sync_dma_for_cpu()
+    - parisc: Flush gatt writes and adjust gatt mask in parisc_agp_mask_memory()
+    - MIPS: unhide PATA_PLATFORM
+    - MIPS: Alchemy: fix dbdma2
+    - mips: Move initrd_start check after initrd address sanitisation.
+    - ASoC: dwc: move DMA init to snd_soc_dai_driver probe()
+    - xen/blkfront: Only check REQ_FUA for writes
+    - drm:amd:amdgpu: Fix missing buffer object unlock in failure path
+    - NVMe: Add MAXIO 1602 to bogus nid list.
+    - irqchip/gic: Correctly validate OF quirk descriptors
+    - wifi: cfg80211: fix locking in regulatory disconnect
+    - wifi: cfg80211: fix double lock bug in reg_wdev_chan_valid()
+    - epoll: ep_autoremove_wake_function should use list_del_init_careful
+    - ocfs2: fix use-after-free when unmounting read-only filesystem
+    - ocfs2: check new file size on fallocate call
+    - nios2: dts: Fix tse_mac "max-frame-size" property
+    - nilfs2: fix incomplete buffer cleanup in nilfs_btnode_abort_change_key()
+    - nilfs2: fix possible out-of-bounds segment allocation in resize ioctl
+    - kexec: support purgatories with .text.hot sections
+    - x86/purgatory: remove PGO flags
+    - powerpc/purgatory: remove PGO flags
+    - ALSA: usb-audio: Add quirk flag for HEM devices to enable native DSD
+      playback
+    - dm thin metadata: check fail_io before using data_sm
+    - nouveau: fix client work fence deletion race
+    - RDMA/uverbs: Restrict usage of privileged QKEYs
+    - net: usb: qmi_wwan: add support for Compal RXM-G1
+    - drm/amdgpu: add missing radeon secondary PCI ID
+    - ALSA: hda/realtek: Add a quirk for Compaq N14JP6
+    - Remove DECnet support from kernel
+    - [Config] updateconfigs for DECNET
+    - thunderbolt: dma_test: Use correct value for absent rings when creating
+      paths
+    - thunderbolt: Mask ring interrupt on Intel hardware as well
+    - USB: serial: option: add Quectel EM061KGL series
+    - serial: lantiq: add missing interrupt ack
+    - usb: dwc3: gadget: Reset num TRBs before giving back the request
+    - RDMA/rtrs: Fix the last iu->buf leak in err path
+    - RDMA/rtrs: Fix rxe_dealloc_pd warning
+    - RDMA/rxe: Fix packet length checks
+    - spi: fsl-dspi: avoid SCK glitches with continuous transfers
+    - netfilter: nf_tables: integrate pipapo into commit protocol
+    - netfilter: nfnetlink: skip error delivery on batch in case of ENOMEM
+    - net: enetc: correct the indexes of highest and 2nd highest TCs
+    - ping6: Fix send to link-local addresses with VRF.
+    - net/sched: simplify tcf_pedit_act
+    - net/sched: act_pedit: remove extra check for key type
+    - net/sched: act_pedit: Parse L3 Header for L4 offset
+    - RDMA/rxe: Remove the unused variable obj
+    - RDMA/rxe: Removed unused name from rxe_task struct
+    - RDMA/rxe: Fix the use-before-initialization error of resp_pkts
+    - iavf: remove mask from iavf_irq_enable_queues()
+    - octeontx2-af: fixed resource availability check
+    - octeontx2-af: fix lbk link credits on cn10k
+    - RDMA/mlx5: Initiate dropless RQ for RAW Ethernet functions
+    - RDMA/cma: Always set static rate to 0 for RoCE
+    - IB/uverbs: Fix to consider event queue closing also upon non-blocking mode
+    - IB/isert: Fix dead lock in ib_isert
+    - IB/isert: Fix possible list corruption in CMA handler
+    - IB/isert: Fix incorrect release of isert connection
+    - net: ethtool: correct MAX attribute value for stats
+    - ipvlan: fix bound dev checking for IPv6 l3s mode
+    - sctp: fix an error code in sctp_sf_eat_auth()
+    - igc: Clean the TX buffer and TX descriptor ring
+    - igb: fix nvm.ops.read() error handling
+    - drm/nouveau: don't detect DSM for non-NVIDIA device
+    - drm/nouveau/dp: check for NULL nv_connector->native_mode
+    - drm/nouveau: add nv_encoder pointer check for NULL
+    - cifs: fix lease break oops in xfstest generic/098
+    - ext4: drop the call to ext4_error() from ext4_get_group_info()
+    - net/sched: cls_api: Fix lockup on flushing explicitly created chain
+    - net: lapbether: only support ethernet devices
+    - dm: don't lock fs when the map is NULL during suspend or resume
+    - net: tipc: resize nlattr array to correct size
+    - selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
+    - afs: Fix vlserver probe RTT handling
+    - cgroup: always put cset in cgroup_css_set_put_fork
+    - rcu/kvfree: Avoid freeing new kfree_rcu() memory after old grace period
+    - neighbour: Remove unused inline function neigh_key_eq16()
+    - net: Remove unused inline function dst_hold_and_use()
+    - net: Remove DECnet leftovers from flow.h.
+    - neighbour: delete neigh_lookup_nodev as not used
+    - of: overlay: add entry to of_overlay_action_name[]
+    - mmc: block: ensure error propagation for non-blk
+    - nilfs2: reject devices with insufficient block count
+    - Linux 5.15.118
+
+  * Jammy update: v5.15.117 upstream stable release (LP: #2030107)
+    - ata: ahci: fix enum constants for gcc-13
+    - gcc-plugins: Reorganize gimple includes for GCC 13
+    - remove the sx8 block driver
+    - [Config] updateconfigs for BLK_DEV_SX8
+    - sfc (gcc13): synchronize ef100_enqueue_skb()'s return type
+    - i40e: Remove string printing for i40e_status
+    - i40e: use int for i40e_status
+    - i40e: fix build warning in ice_fltr_add_mac_to_list()
+    - bonding (gcc13): synchronize bond_{a,t}lb_xmit() types
+    - f2fs: fix iostat lock protection
+    - blk-iocost: avoid 64-bit division in ioc_timer_fn
+    - platform/surface: aggregator: Allow completion work-items to be executed in
+      parallel
+    - spi: qup: Request DMA before enabling clocks
+    - afs: Fix setting of mtime when creating a file/dir/symlink
+    - wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll
+    - neighbour: fix unaligned access to pneigh_entry
+    - net: dsa: lan9303: allow vid != 0 in port_fdb_{add|del} methods
+    - bpf: Fix UAF in task local storage
+    - net/ipv6: fix bool/int mismatch for skip_notify_on_dev_down
+    - net/smc: Avoid to access invalid RMBs' MRs in SMCRv1 ADD LINK CONT
+    - net: enetc: correct the statistics of rx bytes
+    - net/sched: fq_pie: ensure reasonable TCA_FQ_PIE_QUANTUM values
+    - drm/i915: Explain the magic numbers for AUX SYNC/precharge length
+    - drm/i915: Use 18 fast wake AUX sync len
+    - Bluetooth: Fix l2cap_disconnect_req deadlock
+    - Bluetooth: L2CAP: Add missing checks for invalid DCID
+    - qed/qede: Fix scheduling while atomic
+    - wifi: cfg80211: fix locking in sched scan stop work
+    - selftests/bpf: Verify optval=NULL case
+    - selftests/bpf: Fix sockopt_sk selftest
+    - netfilter: conntrack: fix NULL pointer dereference in nf_confirm_cthelper
+    - netfilter: ipset: Add schedule point in call_ad().
+    - ipv6: rpl: Fix Route of Death.
+    - rfs: annotate lockless accesses to sk->sk_rxhash
+    - rfs: annotate lockless accesses to RFS sock flow table
+    - drm/i915/selftests: Increase timeout for live_parallel_switch
+    - drm/i915/selftests: Stop using kthread_stop()
+    - drm/i915/selftests: Add some missing error propagation
+    - net: sched: move rtm_tca_policy declaration to include file
+    - net: sched: act_police: fix sparse errors in tcf_police_dump()
+    - net: sched: fix possible refcount leak in tc_chain_tmplt_add()
+    - bpf: Add extra path pointer check to d_path helper
+    - lib: cpu_rmap: Fix potential use-after-free in irq_cpu_rmap_release()
+    - bnxt_en: Don't issue AP reset during ethtool's reset operation
+    - bnxt_en: Query default VLAN before VNIC setup on a VF
+    - bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks
+    - batman-adv: Broken sync while rescheduling delayed work
+    - Input: xpad - delete a Razer DeathAdder mouse VID/PID entry
+    - Input: psmouse - fix OOB access in Elantech protocol
+    - Input: fix open count when closing inhibited device
+    - ALSA: hda/realtek: Add quirk for Clevo NS50AU
+    - ALSA: hda/realtek: Add a quirk for HP Slim Desktop S01
+    - drm/i915/gt: Use the correct error value when kernel_context() fails
+    - drm/amd/pm: conditionally disable pcie lane switching for some
+      sienna_cichlid SKUs
+    - drm/amdgpu: fix xclk freq on CHIP_STONEY
+    - drm/amd/pm: Fix power context allocation in SMU13
+    - can: j1939: j1939_sk_send_loop_abort(): improved error queue handling in
+      J1939 Socket
+    - can: j1939: change j1939_netdev_lock type to mutex
+    - can: j1939: avoid possible use-after-free when j1939_can_rx_register fails
+    - ceph: fix use-after-free bug for inodes when flushing capsnaps
+    - s390/dasd: Use correct lock while counting channel queue length
+    - Bluetooth: Fix use-after-free in hci_remove_ltk/hci_remove_irk
+    - Bluetooth: hci_qca: fix debugfs registration
+    - tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta'
+    - rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting
+    - rbd: get snapshot context after exclusive lock is ensured to be held
+    - pinctrl: meson-axg: add missing GPIOA_18 gpio group
+    - usb: usbfs: Enforce page requirements for mmap
+    - usb: usbfs: Use consistent mmap functions
+    - ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
+    - ASoC: codecs: wsa881x: do not set can_multi_write flag
+    - arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite
+      boards
+    - arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
+    - arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
+    - ASoC: mediatek: mt8195-afe-pcm: Convert to platform remove callback
+      returning void
+    - ASoC: mediatek: mt8195: fix use-after-free in driver remove path
+    - arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
+    - i2c: mv64xxx: Fix reading invalid status value in atomic mode
+    - firmware: arm_ffa: Set handle field to zero in memory descriptor
+    - i2c: sprd: Delete i2c adapter in .remove's error path
+    - eeprom: at24: also select REGMAP
+    - riscv: fix kprobe __user string arg print fault issue
+    - vduse: avoid empty string for dev name
+    - vhost: support PACKED when setting-getting vring_base
+    - vhost_vdpa: support PACKED when setting-getting vring_base
+    - ext4: only check dquot_initialize_needed() when debugging
+    - Linux 5.15.117
+
+  * CVE-2023-4273
+    - exfat: check if filename entries exceeds max filename length
+
+  * CVE-2023-4128
+    - net/sched: cls_u32: No longer copy tcf_result on update to avoid use-after-
+      free
+    - net/sched: cls_fw: No longer copy tcf_result on update to avoid use-after-
+      free
+    - net/sched: cls_route: No longer copy tcf_result on update to avoid use-
+      after-free
+
+  * CVE-2023-3863
+    - nfc: llcp: simplify llcp_sock_connect() error paths
+    - net: nfc: Fix use-after-free caused by nfc_llcp_find_local
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 01 Sep 2023 14:52:39 +0200
+
+linux (5.15.0-83.92) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-83.92 -proposed tracker (LP: #2031132)
+
+  * libgnutls report "trap invalid opcode" when trying to install packages over
+    https (LP: #2031093)
+    - [Config]: disable CONFIG_GDS_FORCE_MITIGATION
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Mon, 14 Aug 2023 11:05:34 +0200
+
+linux (5.15.0-81.90) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-81.90 -proposed tracker (LP: #2030422)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] resync getabis
+    - debian/dkms-versions -- update from kernel-versions (main/2023.08.07)
+
+  * CVE-2022-40982
+    - x86/mm: Initialize text poking earlier
+    - x86/mm: fix poking_init() for Xen PV guests
+    - x86/mm: Use mm_alloc() in poking_init()
+    - mm: Move mm_cachep initialization to mm_init()
+    - init: Provide arch_cpu_finalize_init()
+    - x86/cpu: Switch to arch_cpu_finalize_init()
+    - ARM: cpu: Switch to arch_cpu_finalize_init()
+    - sparc/cpu: Switch to arch_cpu_finalize_init()
+    - um/cpu: Switch to arch_cpu_finalize_init()
+    - init: Remove check_bugs() leftovers
+    - init: Invoke arch_cpu_finalize_init() earlier
+    - init, x86: Move mem_encrypt_init() into arch_cpu_finalize_init()
+    - x86/init: Initialize signal frame size late
+    - x86/fpu: Remove cpuinfo argument from init functions
+    - x86/fpu: Mark init functions __init
+    - x86/fpu: Move FPU initialization into arch_cpu_finalize_init()
+    - x86/xen: Fix secondary processors' FPU initialization
+    - x86/speculation: Add Gather Data Sampling mitigation
+    - x86/speculation: Add force option to GDS mitigation
+    - x86/speculation: Add Kconfig option for GDS
+    - KVM: Add GDS_NO support to KVM
+    - Documentation/x86: Fix backwards on/off logic about YMM support
+    - [Config]: Enable CONFIG_ARCH_HAS_CPU_FINALIZE_INIT and
+      CONFIG_GDS_FORCE_MITIGATION
+
+  * CVE-2023-3609
+    - net/sched: cls_u32: Fix reference counter leak leading to overflow
+
+  * CVE-2023-21400
+    - io_uring: ensure IOPOLL locks around deferred work
+
+  * CVE-2023-4015
+    - netfilter: nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound
+      set/chain
+    - netfilter: nf_tables: unbind non-anonymous set if rule construction fails
+    - netfilter: nf_tables: skip immediate deactivate in _PREPARE_ERROR
+
+  * CVE-2023-3995
+    - netfilter: nf_tables: disallow rule addition to bound chain via
+      NFTA_RULE_CHAIN_ID
+
+  * CVE-2023-3777
+    - netfilter: nf_tables: skip bound chain on rule flush
+
+  * losetup with mknod fails on jammy with kernel 5.15.0-69-generic
+    (LP: #2015400)
+    - loop: do not enforce max_loop hard limit by (new) default
+
+  * Include the MAC address pass through function on RTL8153DD-CG (LP: #2020295)
+    - r8152: add USB device driver for config selection
+
+  * Jammy update: v5.15.116 upstream stable release (LP: #2029401)
+    - RDMA/bnxt_re: Fix the page_size used during the MR creation
+    - RDMA/efa: Fix unsupported page sizes in device
+    - RDMA/hns: Fix base address table allocation
+    - RDMA/hns: Modify the value of long message loopback slice
+    - dmaengine: at_xdmac: Move the free desc to the tail of the desc list
+    - dmaengine: at_xdmac: fix potential Oops in at_xdmac_prep_interleaved()
+    - RDMA/bnxt_re: Fix a possible memory leak
+    - RDMA/bnxt_re: Fix return value of bnxt_re_process_raw_qp_pkt_rx
+    - iommu/rockchip: Fix unwind goto issue
+    - iommu/amd: Don't block updates to GATag if guest mode is on
+    - dmaengine: pl330: rename _start to prevent build error
+    - riscv: Fix unused variable warning when BUILTIN_DTB is set
+    - net/mlx5: fw_tracer, Fix event handling
+    - net/mlx5e: Don't attach netdev profile while handling internal error
+    - net: mellanox: mlxbf_gige: Fix skb_panic splat under memory pressure
+    - netrom: fix info-leak in nr_write_internal()
+    - af_packet: Fix data-races of pkt_sk(sk)->num.
+    - amd-xgbe: fix the false linkup in xgbe_phy_status
+    - mtd: rawnand: ingenic: fix empty stub helper definitions
+    - RDMA/irdma: Add SW mechanism to generate completions on error
+    - RDMA/irdma: Prevent QP use after free
+    - RDMA/irdma: Fix Local Invalidate fencing
+    - af_packet: do not use READ_ONCE() in packet_bind()
+    - tcp: deny tcp_disconnect() when threads are waiting
+    - tcp: Return user_mss for TCP_MAXSEG in CLOSE/LISTEN state if user_mss set
+    - net/sched: sch_ingress: Only create under TC_H_INGRESS
+    - net/sched: sch_clsact: Only create under TC_H_CLSACT
+    - net/sched: Reserve TC_H_INGRESS (TC_H_CLSACT) for ingress (clsact) Qdiscs
+    - net/sched: Prohibit regrafting ingress or clsact Qdiscs
+    - net: sched: fix NULL pointer dereference in mq_attach
+    - net/netlink: fix NETLINK_LIST_MEMBERSHIPS length report
+    - udp6: Fix race condition in udp6_sendmsg & connect
+    - net/mlx5e: Fix error handling in mlx5e_refresh_tirs
+    - net/mlx5: Read embedded cpu after init bit cleared
+    - net: dsa: mv88e6xxx: Increase wait after reset deactivation
+    - mtd: rawnand: marvell: ensure timing values are written
+    - mtd: rawnand: marvell: don't set the NAND frequency select
+    - rtnetlink: call validate_linkmsg in rtnl_create_link
+    - drm/amdgpu: release gpu full access after "amdgpu_device_ip_late_init"
+    - watchdog: menz069_wdt: fix watchdog initialisation
+    - ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
+    - drm/amdgpu: Use the default reset when loading or reloading the driver
+    - mailbox: mailbox-test: Fix potential double-free in
+      mbox_test_message_write()
+    - drm/ast: Fix ARM compatibility
+    - btrfs: abort transaction when sibling keys check fails for leaves
+    - ARM: 9295/1: unwind:fix unwind abort for uleb128 case
+    - media: rcar-vin: Select correct interrupt mode for V4L2_FIELD_ALTERNATE
+    - platform/x86: intel_scu_pcidrv: Add back PCI ID for Medfield
+    - gfs2: Don't deref jdesc in evict
+    - fbdev: imsttfb: Fix use after free bug in imsttfb_probe
+    - fbdev: modedb: Add 1920x1080 at 60 Hz video mode
+    - fbdev: stifb: Fix info entry in sti_struct on error path
+    - nbd: Fix debugfs_create_dir error checking
+    - block/rnbd: replace REQ_OP_FLUSH with REQ_OP_WRITE
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for HS-SSD-FUTURE 2048G
+    - nvme-pci: add quirk for missing secondary temperature thresholds
+    - ASoC: dwc: limit the number of overrun messages
+    - um: harddog: fix modular build
+    - xfrm: Check if_id in inbound policy/secpath match
+    - ASoC: dt-bindings: Adjust #sound-dai-cells on TI's single-DAI codecs
+    - ASoC: ssm2602: Add workaround for playback distortions
+    - media: dvb_demux: fix a bug for the continuity counter
+    - media: dvb-usb: az6027: fix three null-ptr-deref in az6027_i2c_xfer()
+    - media: dvb-usb-v2: ec168: fix null-ptr-deref in ec168_i2c_xfer()
+    - media: dvb-usb-v2: ce6230: fix null-ptr-deref in ce6230_i2c_master_xfer()
+    - media: dvb-usb-v2: rtl28xxu: fix null-ptr-deref in rtl28xxu_i2c_xfer
+    - media: dvb-usb: digitv: fix null-ptr-deref in digitv_i2c_xfer()
+    - media: dvb-usb: dw2102: fix uninit-value in su3000_read_mac_address
+    - media: netup_unidvb: fix irq init by register it at the end of probe
+    - media: dvb_ca_en50221: fix a size write bug
+    - media: ttusb-dec: fix memory leak in ttusb_dec_exit_dvb()
+    - media: mn88443x: fix !CONFIG_OF error by drop of_match_ptr from ID table
+    - media: dvb-core: Fix use-after-free due on race condition at dvb_net
+    - media: dvb-core: Fix use-after-free due to race at dvb_register_device()
+    - media: dvb-core: Fix use-after-free due to race condition at dvb_ca_en50221
+    - s390/pkey: zeroize key blobs
+    - s390/topology: honour nr_cpu_ids when adding CPUs
+    - ACPI: resource: Add IRQ override quirk for LG UltraPC 17U70P
+    - wifi: rtl8xxxu: fix authentication timeout due to incorrect RCR value
+    - ARM: dts: stm32: add pin map for CAN controller on stm32f7
+    - arm64/mm: mark private VM_FAULT_X defines as vm_fault_t
+    - arm64: vdso: Pass (void *) to virt_to_page()
+    - wifi: mac80211: simplify chanctx allocation
+    - scsi: core: Decrease scsi_device's iorequest_cnt if dispatch failed
+    - wifi: b43: fix incorrect __packed annotation
+    - netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with
+      CONFIG_NF_NAT
+    - nvme-multipath: don't call blk_mark_disk_dead in nvme_mpath_remove_disk
+    - ALSA: oss: avoid missing-prototype warnings
+    - drm/msm: Be more shouty if per-process pgtables aren't working
+    - atm: hide unused procfs functions
+    - drm/amdgpu: skip disabling fence driver src_irqs when device is unplugged
+    - nvme-pci: Add quirk for Teamgroup MP33 SSD
+    - mailbox: mailbox-test: fix a locking issue in mbox_test_message_write()
+    - media: uvcvideo: Don't expose unsupported formats to userspace
+    - iio: accel: st_accel: Fix invalid mount_matrix on devices without ACPI _ONT
+      method
+    - iio: adc: mxs-lradc: fix the order of two cleanup operations
+    - HID: google: add jewel USB id
+    - HID: wacom: avoid integer overflow in wacom_intuos_inout()
+    - iio: imu: inv_icm42600: fix timestamp reset
+    - dt-bindings: iio: adc: renesas,rcar-gyroadc: Fix adi,ad7476 compatible value
+    - iio: light: vcnl4035: fixed chip ID check
+    - iio: adc: ad_sigma_delta: Fix IRQ issue by setting IRQ_DISABLE_UNLAZY flag
+    - iio: dac: mcp4725: Fix i2c_master_send() return value handling
+    - iio: adc: ad7192: Change "shorted" channels to differential
+    - iio: dac: build ad5758 driver when AD5758 is selected
+    - net: usb: qmi_wwan: Set DTR quirk for BroadMobi BM818
+    - dt-bindings: usb: snps,dwc3: Fix "snps,hsphy_interface" type
+    - usb: gadget: f_fs: Add unbind event before functionfs_unbind
+    - md/raid5: fix miscalculation of 'end_sector' in raid5_read_one_chunk()
+    - misc: fastrpc: return -EPIPE to invocations on device removal
+    - misc: fastrpc: reject new invocations during device removal
+    - scsi: stex: Fix gcc 13 warnings
+    - ata: libata-scsi: Use correct device no in ata_find_dev()
+    - drm/amd/pm: reverse mclk and fclk clocks levels for vangogh
+    - drm/amd/pm: reverse mclk and fclk clocks levels for yellow carp
+    - drm/amd/pm: reverse mclk and fclk clocks levels for renoir
+    - x86/boot: Wrap literal addresses in absolute_pointer()
+    - ath6kl: Use struct_group() to avoid size-mismatched casting
+    - block/blk-iocost (gcc13): keep large values in a new enum
+    - mmc: vub300: fix invalid response handling
+    - mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order
+    - tty: serial: fsl_lpuart: use UARTCTRL_TXINV to send break instead of
+      UARTCTRL_SBK
+    - btrfs: fix csum_tree_block page iteration to avoid tripping on
+      -Werror=array-bounds
+    - powerpc/iommu: Limit number of TCEs to 512 for H_STUFF_TCE hcall
+    - iommu/amd: Fix domain flush size when syncing iotlb
+    - usb: cdns3: allocate TX FIFO size according to composite EP number
+    - usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM
+    - block: fix revalidate performance regression
+    - selinux: don't use make's grouped targets feature yet
+    - tracing/probe: trace_probe_primary_from_call(): checked list_first_entry
+    - selftests: mptcp: connect: skip if MPTCP is not supported
+    - selftests: mptcp: pm nl: skip if MPTCP is not supported
+    - selftests: mptcp: sockopt: skip if MPTCP is not supported
+    - ext4: add EA_INODE checking to ext4_iget()
+    - ext4: set lockdep subclass for the ea_inode in ext4_xattr_inode_cache_find()
+    - ext4: disallow ea_inodes with extended attributes
+    - ext4: add lockdep annotations for i_data_sem for ea_inode's
+    - fbcon: Fix null-ptr-deref in soft_cursor
+    - serial: 8250_tegra: Fix an error handling path in tegra_uart_probe()
+    - test_firmware: fix the memory leak of the allocated firmware buffer
+    - KVM: x86: Account fastpath-only VM-Exits in vCPU stats
+    - ksmbd: fix credit count leakage
+    - ksmbd: fix incorrect AllocationSize set in smb2_get_info
+    - KEYS: asymmetric: Copy sig and digest in public_key_verify_signature()
+    - regmap: Account for register length when chunking
+    - tpm, tpm_tis: Request threaded interrupt handler
+    - drm/rcar: stop using 'imply' for dependencies
+    - [Config] updateconfigs for DRM_RCAR_LVDS
+    - scsi: dpt_i2o: Remove broken pass-through ioctl (I2OUSERCMD)
+    - scsi: dpt_i2o: Do not process completions with invalid addresses
+    - [Config] updateconfigs for SCSI_DPT_I2O
+    - drm/amdgpu/gfx10: Disable gfxoff before disabling powergating.
+    - selftests: mptcp: diag: skip if MPTCP is not supported
+    - selftests: mptcp: simult flows: skip if MPTCP is not supported
+    - selftests: mptcp: join: skip if MPTCP is not supported
+    - ext4: enable the lazy init thread when remounting read/write
+    - ARM: defconfig: drop CONFIG_DRM_RCAR_LVDS
+    - RDMA/irdma: Fix drain SQ hang with no completion
+    - RDMA/irdma: Do not generate SW completions for NOPs
+    - Linux 5.15.116
+
+  * CVE-2023-20593
+    - x86/cpu/amd: Move the errata checking functionality up
+    - x86/cpu/amd: Add a Zenbleed fix
+
+  * CVE-2023-4004
+    - netfilter: nft_set_pipapo: fix improper element removal
+
+  * CVE-2023-3611
+    - net/sched: sch_qfq: refactor parsing of netlink parameters
+    - net/sched: sch_qfq: account for stab overhead in qfq_enqueue
+
+  * CVE-2023-3610
+    - netfilter: nf_tables: fix chain binding transaction logic
+
+  * CVE-2023-2898
+    - f2fs: fix to avoid NULL pointer dereference f2fs_write_end_io()
+
+  * Backport support to tolerate ZSTD compressed firmware files (LP: #2028550)
+    - firmware_loader: EXTRA_FIRMWARE does not support compressed files
+    - firmware: Add the support for ZSTD-compressed firmware files
+    - [Config] Enable FW_LOADER_COMPRESS_ZSTD by default
+
+  * stacked overlay file system mounts that have chroot() called against them
+    appear to be getting locked (by the kernel most likely?) (LP: #2016398)
+    - SAUCE: overlayfs: fix reference count mismatch
+
+  * kdump fails on big arm64 systems when offset is not specified (LP: #2024479)
+    - arm64: mm: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
+    - arm64: kdump: Reimplement crashkernel=X
+    - docs: kdump: Update the crashkernel description for arm64
+    - arm64: kdump: Do not allocate crash low memory if not needed
+    - arm64/mm: Define defer_reserve_crashkernel()
+    - arm64: kdump: Provide default size when crashkernel=Y, low is not specified
+    - arm64: kdump: Support crashkernel=X fall back to reserve region above DMA
+      zones
+
+  * usbrtl sometimes doesn't reload firmware (LP: #2026028)
+    - Bluetooth: btrtl: Ask ic_info to drop firmware
+
+  * cifs: fix mid leak during reconnection after timeout threshold
+    (LP: #2029138)
+    - cifs: fix mid leak during reconnection after timeout threshold
+
+  * Jammy update: v5.15.115 upstream stable release (LP: #2028799)
+    - power: supply: bq27xxx: expose battery data when CI=1
+    - power: supply: bq27xxx: Move bq27xxx_battery_update() down
+    - power: supply: bq27xxx: Ensure power_supply_changed() is called on current
+      sign changes
+    - power: supply: bq27xxx: After charger plug in/out wait 0.5s for things to
+      stabilize
+    - power: supply: core: Refactor
+      power_supply_set_input_current_limit_from_supplier()
+    - power: supply: bq24190: Call power_supply_changed() after updating input
+      current
+    - bpf: fix a memory leak in the LRU and LRU_PERCPU hash maps
+    - net/mlx5: devcom only supports 2 ports
+    - net/mlx5e: Fix deadlock in tc route query code
+    - net/mlx5: Devcom, serialize devcom registration
+    - platform/x86: ISST: PUNIT device mapping with Sub-NUMA clustering
+    - platform/x86: ISST: Remove 8 socket limit
+    - net: phy: mscc: enable VSC8501/2 RGMII RX clock
+    - net: dsa: introduce helpers for iterating through ports using dp
+    - net: dsa: mt7530: rework mt753[01]_setup
+    - net: dsa: mt7530: split-off common parts from mt7531_setup
+    - net: dsa: mt7530: fix network connectivity with multiple CPU ports
+    - Bonding: add arp_missed_max option
+    - bonding: fix send_peer_notif overflow
+    - binder: fix UAF caused by faulty buffer cleanup
+    - irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()
+    - irqchip/mips-gic: Use raw spinlock for gic_lock
+    - net/mlx5e: Fix SQ wake logic in ptp napi_poll context
+    - xdp: Allow registering memory model without rxq reference
+    - net: page_pool: use in_softirq() instead
+    - page_pool: fix inconsistency for page_pool_ring_[un]lock()
+    - irqchip/mips-gic: Don't touch vl_map if a local interrupt is not routable
+    - xdp: xdp_mem_allocator can be NULL in trace_mem_connect().
+    - bluetooth: Add cmd validity checks at the start of hci_sock_ioctl()
+    - Revert "binder_alloc: add missing mmap_lock calls when using the VMA"
+    - Revert "android: binder: stop saving a pointer to the VMA"
+    - binder: add lockless binder_alloc_(set|get)_vma()
+    - binder: fix UAF of alloc->vma in race with munmap()
+    - ipv{4,6}/raw: fix output xfrm lookup wrt protocol
+    - netfilter: ctnetlink: Support offloaded conntrack entry deletion
+    - Linux 5.15.115
+
+  * Jammy update: v5.15.114 upstream stable release (LP: #2028701)
+    - usb: gadget: Properly configure the device for remote wakeup
+    - usb: dwc3: fix gadget mode suspend interrupt handler issue
+    - dt-bindings: ata: ahci-ceva: convert to yaml
+    - dt-bindings: ata: ahci-ceva: Cover all 4 iommus entries
+    - watchdog: sp5100_tco: Immediately trigger upon starting.
+    - ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
+    - spi: fsl-spi: Re-organise transfer bits_per_word adaptation
+    - spi: fsl-cpm: Use 16 bit mode for large transfers with even size
+    - ocfs2: Switch to security_inode_init_security()
+    - arm64: Also reset KASAN tag if page is not PG_mte_tagged
+    - ALSA: hda/ca0132: add quirk for EVGA X299 DARK
+    - ALSA: hda: Fix unhandled register update during auto-suspend period
+    - ALSA: hda/realtek: Enable headset onLenovo M70/M90
+    - mmc: sdhci-esdhc-imx: make "no-mmc-hs400" works
+    - ASoC: rt5682: Disable jack detection interrupt during suspend
+    - net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize
+    - m68k: Move signal frame following exception on 68020/030
+    - parisc: Handle kgdb breakpoints only in kernel context
+    - parisc: Allow to reboot machine after system halt
+    - gpio: mockup: Fix mode of debugfs files
+    - btrfs: use nofs when cleaning up aborted transactions
+    - dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size type
+    - selftests/memfd: Fix unknown type name build failure
+    - parisc: Fix flush_dcache_page() for usage from irq context
+    - perf/x86/uncore: Correct the number of CHAs on SPR
+    - x86/topology: Fix erroneous smp_num_siblings on Intel Hybrid platforms
+    - debugobjects: Don't wake up kswapd from fill_pool()
+    - fbdev: udlfb: Fix endpoint check
+    - net: fix stack overflow when LRO is disabled for virtual interfaces
+    - udplite: Fix NULL pointer dereference in __sk_mem_raise_allocated().
+    - USB: core: Add routines for endpoint checks in old drivers
+    - USB: sisusbvga: Add endpoint checks
+    - media: radio-shark: Add endpoint checks
+    - ASoC: lpass: Fix for KASAN use_after_free out of bounds
+    - net: fix skb leak in __skb_tstamp_tx()
+    - selftests: fib_tests: mute cleanup error message
+    - octeontx2-pf: Fix TSOv6 offload
+    - bpf: Fix mask generation for 32-bit narrow loads of 64-bit fields
+    - ipv6: Fix out-of-bounds access in ipv6_find_tlv()
+    - cifs: mapchars mount option ignored
+    - power: supply: leds: Fix blink to LED on transition
+    - power: supply: mt6360: add a check of devm_work_autocancel in
+      mt6360_charger_probe
+    - power: supply: bq27xxx: Fix bq27xxx_battery_update() race condition
+    - power: supply: bq27xxx: Fix I2C IRQ race on remove
+    - power: supply: bq27xxx: Fix poll_interval handling and races on remove
+    - power: supply: bq27xxx: Add cache parameter to
+      bq27xxx_battery_current_and_status()
+    - power: supply: sbs-charger: Fix INHIBITED bit for Status reg
+    - firmware: arm_ffa: Check if ffa_driver remove is present before executing
+    - firmware: arm_ffa: Fix FFA device names for logical partitions
+    - fs: fix undefined behavior in bit shift for SB_NOUSER
+    - regulator: pca9450: Fix BUCK2 enable_mask
+    - coresight: Fix signedness bug in tmc_etr_buf_insert_barrier_packet()
+    - xen/pvcalls-back: fix double frees with pvcalls_new_active_socket()
+    - x86/show_trace_log_lvl: Ensure stack pointer is aligned, again
+    - ASoC: Intel: Skylake: Fix declaration of enum skl_ch_cfg
+    - sctp: fix an issue that plpmtu can never go to complete state
+    - forcedeth: Fix an error handling path in nv_probe()
+    - platform/mellanox: mlxbf-pmc: fix sscanf() error checking
+    - net/mlx5e: do as little as possible in napi poll when budget is 0
+    - net/mlx5: DR, Fix crc32 calculation to work on big-endian (BE) CPUs
+    - net/mlx5: DR, Check force-loopback RC QP capability independently from RoCE
+    - net/mlx5: Fix error message when failing to allocate device memory
+    - net/mlx5: Devcom, fix error flow in mlx5_devcom_register_device
+    - arm64: dts: imx8mn-var-som: fix PHY detection bug by adding deassert delay
+    - firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors
+    - regulator: mt6359: add read check for PMIC MT6359
+    - 3c589_cs: Fix an error handling path in tc589_probe()
+    - net: phy: mscc: add VSC8502 to MODULE_DEVICE_TABLE
+    - Linux 5.15.114
+
+  * Jammy update: v5.15.113 upstream stable release (LP: #2028408)
+    - drm/mipi-dsi: Set the fwnode for mipi_dsi_device
+    - ARM: 9296/1: HP Jornada 7XX: fix kernel-doc warnings
+    - net: mdio: mvusb: Fix an error handling path in mvusb_mdio_probe()
+    - scsi: ufs: core: Fix I/O hang that occurs when BKOPS fails in W-LUN suspend
+    - tick/broadcast: Make broadcast device replacement work correctly
+    - linux/dim: Do nothing if no time delta between samples
+    - net: stmmac: switch to use interrupt for hw crosstimestamping
+    - net: stmmac: Initialize MAC_ONEUS_TIC_COUNTER register
+    - net: Fix load-tearing on sk->sk_stamp in sock_recv_cmsgs().
+    - netfilter: nf_tables: always release netdev hooks from notifier
+    - netfilter: conntrack: fix possible bug_on with enable_hooks=1
+    - netlink: annotate accesses to nlk->cb_running
+    - net: annotate sk->sk_err write from do_recvmmsg()
+    - net: deal with most data-races in sk_wait_event()
+    - net: add vlan_get_protocol_and_depth() helper
+    - tcp: add annotations around sk->sk_shutdown accesses
+    - gve: Remove the code of clearing PBA bit
+    - net: datagram: fix data-races in datagram_poll()
+    - af_unix: Fix a data race of sk->sk_receive_queue->qlen.
+    - af_unix: Fix data races around sk->sk_shutdown.
+    - drm/i915/dp: prevent potential div-by-zero
+    - fbdev: arcfb: Fix error handling in arcfb_probe()
+    - ext4: remove an unused variable warning with CONFIG_QUOTA=n
+    - ext4: reflect error codes from ext4_multi_mount_protect() to its callers
+    - ext4: fix lockdep warning when enabling MMP
+    - ext4: allow to find by goal if EXT4_MB_HINT_GOAL_ONLY is set
+    - ext4: allow ext4_get_group_info() to fail
+    - refscale: Move shutdown from wait_event() to wait_event_idle()
+    - rcu: Protect rcu_print_task_exp_stall() ->exp_tasks access
+    - fs: hfsplus: remove WARN_ON() from hfsplus_cat_{read,write}_inode()
+    - drm/displayid: add displayid_get_header() and check bounds better
+    - drm/amd/display: Use DC_LOG_DC in the trasform pixel function
+    - regmap: cache: Return error in cache sync operations for REGCACHE_NONE
+    - arm64: dts: qcom: msm8996: Add missing DWC3 quirks
+    - media: cx23885: Fix a null-ptr-deref bug in buffer_prepare() and
+      buffer_finish()
+    - media: pci: tw68: Fix null-ptr-deref bug in buf prepare and finish
+    - firmware: arm_sdei: Fix sleep from invalid context BUG
+    - ACPI: EC: Fix oops when removing custom query handlers
+    - remoteproc: stm32_rproc: Add mutex protection for workqueue
+    - drm/tegra: Avoid potential 32-bit integer overflow
+    - drm/msm/dp: Clean up handling of DP AUX interrupts
+    - ACPICA: Avoid undefined behavior: applying zero offset to null pointer
+    - ACPICA: ACPICA: check null return of ACPI_ALLOCATE_ZEROED in
+      acpi_db_display_objects
+    - drm/amd: Fix an out of bounds error in BIOS parser
+    - media: Prefer designated initializers over memset for subdev pad ops
+    - wifi: ath: Silence memcpy run-time false positive warning
+    - bpf: Annotate data races in bpf_local_storage
+    - wifi: brcmfmac: cfg80211: Pass the PMK in binary instead of hex
+    - ext2: Check block size validity during mount
+    - scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow
+    - bnxt: avoid overflow in bnxt_get_nvram_directory()
+    - net: pasemi: Fix return type of pasemi_mac_start_tx()
+    - net: Catch invalid index in XPS mapping
+    - scsi: target: iscsit: Free cmds before session free
+    - lib: cpu_rmap: Avoid use after free on rmap->obj array entries
+    - scsi: message: mptlan: Fix use after free bug in mptlan_remove() due to race
+      condition
+    - gfs2: Fix inode height consistency check
+    - scsi: ufs: ufs-pci: Add support for Intel Lunar Lake
+    - ext4: set goal start correctly in ext4_mb_normalize_request
+    - ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()
+    - f2fs: fix to drop all dirty pages during umount() if cp_error is set
+    - f2fs: fix to check readonly condition correctly
+    - samples/bpf: Fix fout leak in hbm's run_bpf_prog
+    - bpf: Add preempt_count_{sub,add} into btf id deny list
+    - wifi: iwlwifi: pcie: fix possible NULL pointer dereference
+    - wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf
+    - null_blk: Always check queue mode setting from configfs
+    - wifi: iwlwifi: dvm: Fix memcpy: detected field-spanning write backtrace
+    - wifi: ath11k: Fix SKB corruption in REO destination ring
+    - nbd: fix incomplete validation of ioctl arg
+    - ipvs: Update width of source for ip_vs_sync_conn_options
+    - Bluetooth: btintel: Add LE States quirk support
+    - Bluetooth: hci_bcm: Fall back to getting bdaddr from EFI if not set
+    - Bluetooth: L2CAP: fix "bad unlock balance" in l2cap_disconnect_rsp
+    - HID: logitech-hidpp: Don't use the USB serial for USB devices
+    - HID: logitech-hidpp: Reconcile USB and Unifying serials
+    - spi: spi-imx: fix MX51_ECSPI_* macros when cs > 3
+    - HID: wacom: generic: Set battery quirk only when we see battery data
+    - usb: typec: tcpm: fix multiple times discover svids error
+    - serial: 8250: Reinit port->pm on port specific driver unbind
+    - mcb-pci: Reallocate memory region to avoid memory overlapping
+    - sched: Fix KCSAN noinstr violation
+    - recordmcount: Fix memory leaks in the uwrite function
+    - RDMA/core: Fix multiple -Warray-bounds warnings
+    - iommu/arm-smmu-qcom: Limit the SMR groups to 128
+    - fs/ntfs3: Fix NULL pointer dereference in 'ni_write_inode'
+    - fs/ntfs3: Enhance the attribute size check
+    - fs/ntfs3: Fix NULL dereference in ni_write_inode
+    - fs/ntfs3: Validate MFT flags before replaying logs
+    - fs/ntfs3: Add length check in indx_get_root
+    - fs/ntfs3: Fix a possible null-pointer dereference in ni_clear()
+    - clk: tegra20: fix gcc-7 constant overflow warning
+    - iommu/arm-smmu-v3: Acknowledge pri/event queue overflow if any
+    - iommu/sprd: Release dma buffer to avoid memory leak
+    - Input: xpad - add constants for GIP interface numbers
+    - phy: st: miphy28lp: use _poll_timeout functions for waits
+    - soundwire: qcom: gracefully handle too many ports in DT
+    - mfd: dln2: Fix memory leak in dln2_probe()
+    - parisc: Replace regular spinlock with spin_trylock on panic path
+    - platform/x86: hp-wmi: Support touchpad on/off
+    - [Config] updateconfigs for X86_PLATFORM_DRIVERS_HP
+    - platform/x86: Move existing HP drivers to a new hp subdir
+    - platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct
+    - xfrm: don't check the default policy if the policy allows the packet
+    - Revert "Fix XFRM-I support for nested ESP tunnels"
+    - drm/msm/dp: unregister audio driver during unbind
+    - drm/msm/dpu: Add INTF_5 interrupts
+    - drm/msm/dpu: Move non-MDP_TOP INTF_INTR offsets out of hwio header
+    - drm/msm/dpu: Remove duplicate register defines from INTF
+    - dt-bindings: display/msm: dsi-controller-main: Document qcom, master-dsi and
+      qcom, sync-dual-dsi
+    - ASoC: fsl_micfil: Fix error handler with pm_runtime_enable
+    - cpupower: Make TSC read per CPU for Mperf monitor
+    - af_key: Reject optional tunnel/BEET mode templates in outbound policies
+    - selftests: seg6: disable DAD on IPv6 router cfg for srv6_end_dt4_l3vpn_test
+    - selftets: seg6: disable rp_filter by default in srv6_end_dt4_l3vpn_test
+    - net: fec: Better handle pm_runtime_get() failing in .remove()
+    - net: phy: dp83867: add w/a for packet errors seen with short cables
+    - ALSA: firewire-digi00x: prevent potential use after free
+    - ALSA: hda/realtek: Apply HP B&O top speaker profile to Pavilion 15
+    - vsock: avoid to close connected socket after the timeout
+    - tcp: fix possible sk_priority leak in tcp_v4_send_reset()
+    - serial: arc_uart: fix of_iomap leak in `arc_serial_probe`
+    - serial: 8250_bcm7271: balance clk_enable calls
+    - serial: 8250_bcm7271: fix leak in `brcmuart_probe`
+    - erspan: get the proto with the md version for collect_md
+    - net: hns3: fix output information incomplete for dumping tx queue info with
+      debugfs
+    - net: hns3: fix sending pfc frames after reset issue
+    - net: hns3: fix reset delay time to avoid configuration timeout
+    - media: netup_unidvb: fix use-after-free at del_timer()
+    - SUNRPC: double free xprt_ctxt while still in use
+    - tracing: Introduce helpers to safely handle dynamic-sized sockaddrs
+    - SUNRPC: Clean up svc_deferred_class trace events
+    - SUNRPC: Remove dead code in svc_tcp_release_rqst()
+    - SUNRPC: Remove svc_rqst::rq_xprt_hlen
+    - SUNRPC: always free ctxt when freeing deferred request
+    - SUNRPC: Fix trace_svc_register() call site
+    - drm/exynos: fix g2d_open/close helper function definitions
+    - net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
+    - virtio-net: Maintain reverse cleanup order
+    - virtio_net: Fix error unwinding of XDP initialization
+    - tipc: add tipc_bearer_min_mtu to calculate min mtu
+    - tipc: do not update mtu if msg_max is too small in mtu negotiation
+    - tipc: check the bearer min mtu properly when setting it by netlink
+    - s390/cio: include subchannels without devices also for evaluation
+    - net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()
+    - net: bcmgenet: Restore phy_stop() depending upon suspend/close
+    - wifi: mac80211: fix min center freq offset tracing
+    - wifi: iwlwifi: mvm: fix cancel_delayed_work_sync() deadlock
+    - wifi: iwlwifi: mvm: don't trust firmware n_channels
+    - scsi: storvsc: Don't pass unused PFNs to Hyper-V host
+    - cassini: Fix a memory leak in the error handling path of cas_init_one()
+    - net: dsa: mv88e6xxx: Fix mv88e6393x EPC write command offset
+    - igb: fix bit_shift to be in [1..8] range
+    - vlan: fix a potential uninit-value in vlan_dev_hard_start_xmit()
+    - netfilter: nf_tables: fix nft_trans type confusion
+    - netfilter: nft_set_rbtree: fix null deref on element insertion
+    - bridge: always declare tunnel functions
+    - ALSA: usb-audio: Add a sample rate workaround for Line6 Pod Go
+    - USB: usbtmc: Fix direction for 0-length ioctl control messages
+    - usb-storage: fix deadlock when a scsi command timeouts more than once
+    - USB: UHCI: adjust zhaoxin UHCI controllers OverCurrent bit value
+    - usb: dwc3: debugfs: Resume dwc3 before accessing registers
+    - usb: gadget: u_ether: Fix host MAC address case
+    - usb: typec: altmodes/displayport: fix pin_assignment_show
+    - xhci-pci: Only run d3cold avoidance quirk for s2idle
+    - xhci: Fix incorrect tracking of free space on transfer rings
+    - ALSA: hda: Fix Oops by 9.1 surround channel names
+    - ALSA: hda: Add NVIDIA codec IDs a3 through a7 to patch table
+    - ALSA: hda/realtek: Add quirk for Clevo L140AU
+    - ALSA: hda/realtek: Add a quirk for HP EliteDesk 805
+    - ALSA: hda/realtek: Add quirk for 2nd ASUS GU603
+    - can: j1939: recvmsg(): allow MSG_CMSG_COMPAT flag
+    - can: isotp: recvmsg(): allow MSG_CMSG_COMPAT flag
+    - can: kvaser_pciefd: Set CAN_STATE_STOPPED in kvaser_pciefd_stop()
+    - can: kvaser_pciefd: Call request_irq() before enabling interrupts
+    - can: kvaser_pciefd: Empty SRB buffer in probe
+    - can: kvaser_pciefd: Clear listen-only bit if not explicitly requested
+    - can: kvaser_pciefd: Do not send EFLUSH command on TFD interrupt
+    - can: kvaser_pciefd: Disable interrupts in probe error path
+    - SMB3: Close all deferred handles of inode in case of handle lease break
+    - SMB3: drop reference to cfile before sending oplock break
+    - ksmbd: smb2: Allow messages padded to 8byte boundary
+    - ksmbd: allocate one more byte for implied bcc[0]
+    - ksmbd: fix wrong UserName check in session_user
+    - ksmbd: fix global-out-of-bounds in smb2_find_context_vals
+    - statfs: enforce statfs[64] structure initialization
+    - serial: Add support for Advantech PCI-1611U card
+    - serial: 8250_exar: Add support for USR298x PCI Modems
+    - serial: qcom-geni: fix enabling deactivated interrupt
+    - thunderbolt: Clear registers properly when auto clear isn't in use
+    - vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF
+    - ceph: force updating the msg pointer in non-split case
+    - powerpc/iommu: Incorrect DDW Table is referenced for SR-IOV device
+    - tpm/tpm_tis: Disable interrupts for more Lenovo devices
+    - powerpc/64s/radix: Fix soft dirty tracking
+    - nilfs2: fix use-after-free bug of nilfs_root in nilfs_evict_inode()
+    - s390/qdio: fix do_sqbs() inline assembly constraint
+    - HID: wacom: Force pen out of prox if no events have been received in a while
+    - HID: wacom: Add new Intuos Pro Small (PTH-460) device IDs
+    - HID: wacom: add three styli to wacom_intuos_get_tool_type
+    - Linux 5.15.113
+
+  * Jammy update: v5.15.112 upstream stable release (LP: #2026607)
+    - ring-buffer: Ensure proper resetting of atomic variables in
+      ring_buffer_reset_online_cpus
+    - crypto: ccp - Clear PSP interrupt status register before calling handler
+    - ubifs: Fix AA deadlock when setting xattr for encrypted file
+    - ubifs: Fix memory leak in do_rename
+    - bus: mhi: Move host MHI code to "host" directory
+    - bus: mhi: host: Remove duplicate ee check for syserr
+    - bus: mhi: host: Use mhi_tryset_pm_state() for setting fw error state
+    - bus: mhi: host: Range check CHDBOFF and ERDBOFF
+    - mailbox: zynq: Switch to flexible array to simplify code
+    - mailbox: zynqmp: Fix counts of child nodes
+    - ASoC: soc-pcm: use GFP_ATOMIC for dpcm structure
+    - ASoC: soc-pcm: align BE 'atomicity' with that of the FE
+    - ASoC: soc-pcm: Fix and cleanup DPCM locking
+    - ASoC: soc-pcm: serialize BE triggers
+    - ASoC: soc-pcm: test refcount before triggering
+    - ASoC: soc-pcm: fix BE handling of PAUSE_RELEASE
+    - fs/ntfs3: Fix null-ptr-deref on inode->i_op in ntfs_lookup()
+    - drm/hyperv: Don't overwrite dirt_needed value set by host
+    - scsi: qedi: Fix use after free bug in qedi_remove()
+    - net/ncsi: clear Tx enable mode when handling a Config required AEN
+    - net/sched: cls_api: remove block_cb from driver_list before freeing
+    - sit: update dev->needed_headroom in ipip6_tunnel_bind_dev()
+    - selftests: srv6: make srv6_end_dt46_l3vpn_test more robust
+    - net: dsa: mv88e6xxx: add mv88e6321 rsvd2cpu
+    - writeback: fix call of incorrect macro
+    - watchdog: dw_wdt: Fix the error handling path of dw_wdt_drv_probe()
+    - RISC-V: mm: Enable huge page support to kernel_page_present() function
+    - net/sched: act_mirred: Add carrier check
+    - r8152: fix flow control issue of RTL8156A
+    - r8152: fix the poor throughput for 2.5G devices
+    - r8152: move setting r8153b_rx_agg_chg_indicate()
+    - sfc: Fix module EEPROM reporting for QSFP modules
+    - rxrpc: Fix hard call timeout units
+    - octeontx2-af: Secure APR table update with the lock
+    - octeontx2-af: Skip PFs if not enabled
+    - octeontx2-pf: Disable packet I/O for graceful exit
+    - octeontx2-vf: Detach LF resources on probe cleanup
+    - ionic: remove noise from ethtool rxnfc error msg
+    - ethtool: Fix uninitialized number of lanes
+    - ionic: catch failure from devlink_alloc
+    - af_packet: Don't send zero-byte data in packet_sendmsg_spkt().
+    - drm/amdgpu: add a missing lock for AMDGPU_SCHED
+    - ALSA: caiaq: input: Add error handling for unsupported input methods in
+      `snd_usb_caiaq_input_init`
+    - net: dsa: mt7530: fix corrupt frames using trgmii on 40 MHz XTAL MT7621
+    - virtio_net: split free_unused_bufs()
+    - virtio_net: suppress cpu stall when free_unused_bufs
+    - net: enetc: check the index of the SFI rather than the handle
+    - perf scripts intel-pt-events.py: Fix IPC output for Python 2
+    - perf vendor events power9: Remove UTF-8 characters from JSON files
+    - perf pmu: zfree() expects a pointer to a pointer to zero it after freeing
+      its contents
+    - perf map: Delete two variable initialisations before null pointer checks in
+      sort__sym_from_cmp()
+    - crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
+    - crypto: engine - check if BH is disabled during completion
+    - crypto: api - Add scaffolding to change completion function signature
+    - crypto: engine - Use crypto_request_complete
+    - crypto: engine - fix crypto_queue backlog handling
+    - perf symbols: Fix return incorrect build_id size in elf_read_build_id()
+    - perf evlist: Refactor evlist__for_each_cpu()
+    - perf stat: Separate bperf from bpf_profiler
+    - btrfs: fix btrfs_prev_leaf() to not return the same key twice
+    - btrfs: zoned: fix wrong use of bitops API in btrfs_ensure_empty_zones
+    - btrfs: fix encoded write i_size corruption with no-holes
+    - btrfs: don't free qgroup space unless specified
+    - btrfs: zero the buffer before marking it dirty in btrfs_redirty_list_add
+    - btrfs: print-tree: parent bytenr must be aligned to sector size
+    - btrfs: fix space cache inconsistency after error loading it from disk
+    - cifs: fix pcchunk length type in smb2_copychunk_range
+    - cifs: release leases for deferred close handles when freezing
+    - platform/x86: touchscreen_dmi: Add upside-down quirk for GDIX1002 ts on the
+      Juno Tablet
+    - platform/x86: touchscreen_dmi: Add info for the Dexp Ursus KX210i
+    - inotify: Avoid reporting event with invalid wd
+    - smb3: fix problem remounting a share after shutdown
+    - SMB3: force unmount was failing to close deferred close files
+    - sh: math-emu: fix macro redefined warning
+    - sh: mcount.S: fix build error when PRINTK is not enabled
+    - sh: init: use OF_EARLY_FLATTREE for early init
+    - sh: nmi_debug: fix return value of __setup handler
+    - remoteproc: stm32: Call of_node_put() on iteration error
+    - remoteproc: st: Call of_node_put() on iteration error
+    - remoteproc: imx_rproc: Call of_node_put() on iteration error
+    - ARM: dts: exynos: fix WM8960 clock name in Itop Elite
+    - ARM: dts: s5pv210: correct MIPI CSIS clock name
+    - drm/bridge: lt8912b: Fix DSI Video Mode
+    - drm/msm: fix NULL-deref on snapshot tear down
+    - drm/msm: fix NULL-deref on irq uninstall
+    - f2fs: fix potential corruption when moving a directory
+    - drm/panel: otm8009a: Set backlight parent to panel device
+    - drm/amd/display: fix flickering caused by S/G mode
+    - drm/amdgpu: fix an amdgpu_irq_put() issue in gmc_v9_0_hw_fini()
+    - drm/amdgpu/gfx: disable gfx9 cp_ecc_error_irq only when enabling legacy gfx
+      ras
+    - drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)
+    - drm/amdgpu: disable sdma ecc irq only when sdma RAS is enabled in suspend
+    - HID: wacom: Set a default resolution for older tablets
+    - HID: wacom: insert timestamp to packed Bluetooth (BT) events
+    - fs/ntfs3: Refactoring of various minor issues
+    - ASoC: soc-pcm: Fix DPCM lockdep warning due to nested stream locks
+    - ASoC: soc-compress: Inherit atomicity from DAI link for Compress FE
+    - ASoC: soc-pcm: Move debugfs removal out of spinlock
+    - ASoC: DPCM: Don't pick up BE without substream
+    - ASoC: soc-pcm.c: call __soc_pcm_close() in soc_pcm_close()
+    - drm/i915/dg2: Support 4k@30 on HDMI
+    - drm/i915/dg2: Add additional HDMI pixel clock frequencies
+    - drm/i915/dg2: Add HDMI pixel clock frequencies 267.30 and 319.89 MHz
+    - drm/msm: Remove struct_mutex usage
+    - drm/msm/adreno: fix runtime PM imbalance at gpu load
+    - drm/amd/display: Refine condition of cursor visibility for pipe-split
+    - drm/amd/display: Add NULL plane_state check for cursor disable logic
+    - wifi: rtw88: rtw8821c: Fix rfe_option field width
+    - ksmbd: set RSS capable in FSCTL_QUERY_NETWORK_INTERFACE_INFO
+    - ksmbd: fix multi session connection failure
+    - ksmbd: replace sessions list in connection with xarray
+    - ksmbd: add channel rwlock
+    - ksmbd: fix kernel oops from idr_remove()
+    - ksmbd: fix racy issue while destroying session on multichannel
+    - ksmbd: fix deadlock in ksmbd_find_crypto_ctx()
+    - ksmbd: not allow guest user on multichannel
+    - locking/rwsem: Add __always_inline annotation to __down_read_common() and
+      inlined callers
+    - ext4: fix WARNING in mb_find_extent
+    - ext4: avoid a potential slab-out-of-bounds in ext4_group_desc_csum
+    - ext4: fix data races when using cached status extents
+    - ext4: check iomap type only if ext4_iomap_begin() does not fail
+    - ext4: improve error recovery code paths in __ext4_remount()
+    - ext4: improve error handling from ext4_dirhash()
+    - ext4: fix deadlock when converting an inline directory in nojournal mode
+    - ext4: add bounds checking in get_max_inline_xattr_value_size()
+    - ext4: bail out of ext4_xattr_ibody_get() fails for any reason
+    - ext4: remove a BUG_ON in ext4_mb_release_group_pa()
+    - ext4: fix invalid free tracking in ext4_xattr_move_to_block()
+    - drm/msm/adreno: adreno_gpu: Use suspend() instead of idle() on load error
+    - serial: 8250: Fix serial8250_tx_empty() race with DMA Tx
+    - drbd: correctly submit flush bio on barrier
+    - RISC-V: Fix up a cherry-pick warning in setup_vm_final()
+    - drm/amd/display: Fix hang when skipping modeset
+    - Linux 5.15.112
+
+  * CVE-2023-31084 // CVE-2023-31084 was assigned to this bug.
+    - media: dvb-core: Fix kernel WARNING for blocking operation in wait_event*()
+
+  * CVE-2023-3776
+    - net/sched: cls_fw: Fix improper refcount update leads to use-after-free
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 09 Aug 2023 16:35:58 +0200
+
+linux (5.15.0-79.86) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-79.86 -proposed tracker (LP: #2026531)
+
+  * Jammy update: v5.15.111 upstream stable release (LP: #2025095)
+    - ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15
+    - ASoC: soc-pcm: fix hw->formats cleared by soc_pcm_hw_init() for dpcm
+    - x86/hyperv: Block root partition functionality in a Confidential VM
+    - iio: adc: palmas_gpadc: fix NULL dereference on rmmod
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Acer Iconia One 7 B1-750
+    - selftests mount: Fix mount_setattr_test builds failed
+    - asm-generic/io.h: suppress endianness warnings for readq() and writeq()
+    - x86/cpu: Add model number for Intel Arrow Lake processor
+    - wireguard: timers: cast enum limits members to int in prints
+    - wifi: mt76: mt7921e: Set memory space enable in PCI_COMMAND if unset
+    - arm64: Always load shadow stack pointer directly from the task struct
+    - arm64: Stash shadow stack pointer in the task struct on interrupt
+    - PCI: pciehp: Fix AB-BA deadlock between reset_lock and device_lock
+    - PCI: qcom: Fix the incorrect register usage in v2.7.0 config
+    - IMA: allow/fix UML builds
+    - USB: dwc3: fix runtime pm imbalance on probe errors
+    - USB: dwc3: fix runtime pm imbalance on unbind
+    - hwmon: (k10temp) Check range scale when CUR_TEMP register is read-write
+    - hwmon: (adt7475) Use device_property APIs when configuring polarity
+    - posix-cpu-timers: Implement the missing timer_wait_running callback
+    - blk-mq: release crypto keyslot before reporting I/O complete
+    - blk-crypto: make blk_crypto_evict_key() return void
+    - blk-crypto: make blk_crypto_evict_key() more robust
+    - ext4: use ext4_journal_start/stop for fast commit transactions
+    - staging: iio: resolver: ads1210: fix config mode
+    - tty: Prevent writing chars during tcsetattr TCSADRAIN/FLUSH
+    - xhci: fix debugfs register accesses while suspended
+    - tick/nohz: Fix cpu_is_hotpluggable() by checking with nohz subsystem
+    - MIPS: fw: Allow firmware to pass a empty env
+    - ipmi:ssif: Add send_retries increment
+    - ipmi: fix SSIF not responding under certain cond.
+    - kheaders: Use array declaration instead of char
+    - wifi: mt76: add missing locking to protect against concurrent rx/status
+      calls
+    - pwm: meson: Fix axg ao mux parents
+    - pwm: meson: Fix g12a ao clk81 name
+    - soundwire: qcom: correct setting ignore bit on v1.5.1
+    - pinctrl: qcom: lpass-lpi: set output value before enabling output
+    - ring-buffer: Sync IRQ works before buffer destruction
+    - crypto: api - Demote BUG_ON() in crypto_unregister_alg() to a WARN_ON()
+    - crypto: safexcel - Cleanup ring IRQ workqueues on load failure
+    - rcu: Avoid stack overflow due to __rcu_irq_enter_check_tick() being kprobe-
+      ed
+    - reiserfs: Add security prefix to xattr name in reiserfs_security_write()
+    - KVM: nVMX: Emulate NOPs in L2, and PAUSE if it's not intercepted
+    - relayfs: fix out-of-bounds access in relay_file_read
+    - writeback, cgroup: fix null-ptr-deref write in bdi_split_work_to_wbs
+    - ksmbd: call rcu_barrier() in ksmbd_server_exit()
+    - ksmbd: fix NULL pointer dereference in smb2_get_info_filesystem()
+    - ksmbd: fix memleak in session setup
+    - i2c: omap: Fix standard mode false ACK readings
+    - riscv: mm: remove redundant parameter of create_fdt_early_page_table
+    - tracing: Fix permissions for the buffer_percent file
+    - iommu/amd: Fix "Guest Virtual APIC Table Root Pointer" configuration in IRTE
+    - ubifs: Fix memleak when insert_old_idx() failed
+    - ubi: Fix return value overwrite issue in try_write_vid_and_data()
+    - ubifs: Free memory for tmpfile name
+    - xfs: don't consider future format versions valid
+    - sound/oss/dmasound: fix build when drivers are mixed =y/=m
+    - rcu: Fix missing TICK_DEP_MASK_RCU_EXP dependency check
+    - selftests/resctrl: Return NULL if malloc_and_init_memory() did not alloc mem
+    - selftests/resctrl: Extend CPU vendor detection
+    - selftests/resctrl: Move ->setup() call outside of test specific branches
+    - selftests/resctrl: Allow ->setup() to return errors
+    - selftests/resctrl: Check for return value after write_schemata()
+    - selinux: fix Makefile dependencies of flask.h
+    - selinux: ensure av_permissions.h is built when needed
+    - tpm, tpm_tis: Do not skip reset of original interrupt vector
+    - tpm, tpm_tis: Claim locality before writing TPM_INT_ENABLE register
+    - tpm, tpm_tis: Disable interrupts if tpm_tis_probe_irq() failed
+    - tpm, tpm_tis: Claim locality before writing interrupt registers
+    - tpm, tpm: Implement usage counter for locality
+    - tpm, tpm_tis: Claim locality when interrupts are reenabled on resume
+    - erofs: stop parsing non-compact HEAD index if clusterofs is invalid
+    - erofs: fix potential overflow calculating xattr_isize
+    - drm/rockchip: Drop unbalanced obj unref
+    - drm/vgem: add missing mutex_destroy
+    - drm/probe-helper: Cancel previous job before starting new one
+    - tools/x86/kcpuid: Fix avx512bw and avx512lvl fields in Fn00000007
+    - soc: ti: pm33xx: Fix refcount leak in am33xx_pm_probe
+    - arm64: dts: renesas: r8a77990: Remove bogus voltages from OPP table
+    - arm64: dts: renesas: r8a774c0: Remove bogus voltages from OPP table
+    - drm/msm/disp/dpu: check for crtc enable rather than crtc active to release
+      shared resources
+    - EDAC/skx: Fix overflows on the DRAM row address mapping arrays
+    - regulator: core: Shorten off-on-delay-us for always-on/boot-on by time since
+      booted
+    - arm64: dts: ti: k3-j721e-main: Remove ti,strobe-sel property
+    - arm64: dts: broadcom: bcm4908: add DT for Netgear RAXE500
+    - arm64: dts: Add DTS files for bcmbca SoC BCM63158
+    - arm64: dts: Add DTS files for bcmbca SoC BCM4912
+    - ARM64: dts: Add DTS files for bcmbca SoC BCM6858
+    - arm64: dts: Add base DTS file for bcmbca device Asus GT-AX6000
+    - arm64: dts: Move BCM4908 dts to bcmbca folder
+    - arm64: dts: broadcom: bcmbca: bcm4908: fix NAND interrupt name
+    - arm64: dts: broadcom: bcmbca: bcm4908: fix procmon nodename
+    - arm64: dts: qcom: msm8998: Fix stm-stimulus-base reg name
+    - arm64: dts: qcom: sdm845: correct dynamic power coefficients
+    - arm64: dts: qcom: sdm845: Fix the PCI I/O port range
+    - arm64: dts: qcom: msm8998: Fix the PCI I/O port range
+    - arm64: dts: qcom: ipq8074: Fix the PCI I/O port range
+    - arm64: dts: qcom: ipq6018: Fix the PCI I/O port range
+    - arm64: dts: qcom: msm8996: Fix the PCI I/O port range
+    - arm64: dts: qcom: sm8250: Fix the PCI I/O port range
+    - ARM: dts: qcom: ipq4019: Fix the PCI I/O port range
+    - ARM: dts: qcom: ipq8064: reduce pci IO size to 64K
+    - ARM: dts: qcom: ipq8064: Fix the PCI I/O port range
+    - x86/MCE/AMD: Use an u64 for bank_map
+    - media: bdisp: Add missing check for create_workqueue
+    - media: av7110: prevent underflow in write_ts_to_decoder()
+    - firmware: qcom_scm: Clear download bit during reboot
+    - drm/bridge: adv7533: Fix adv7533_mode_valid for adv7533 and adv7535
+    - media: max9286: Free control handler
+    - drm/msm/adreno: Defer enabling runpm until hw_init()
+    - drm/msm/adreno: drop bogus pm_runtime_set_active()
+    - drm: msm: adreno: Disable preemption on Adreno 510
+    - drm/amd/display/dc/dce60/Makefile: Fix previous attempt to silence known
+      override-init warnings
+    - ACPI: processor: Fix evaluating _PDC method when running as Xen dom0
+    - mmc: sdhci-of-esdhc: fix quirk to ignore command inhibit for data
+    - drm: rcar-du: Fix a NULL vs IS_ERR() bug
+    - ARM: dts: gta04: fix excess dma channel usage
+    - firmware: arm_scmi: Fix xfers allocation on Rx channel
+    - ACPI: VIOT: Initialize the correct IOMMU fwspec
+    - drm/lima/lima_drv: Add missing unwind goto in lima_pdev_probe()
+    - mailbox: mpfs: switch to txdone_poll
+    - arm64: dts: qcom: sc7180-trogdor-lazor: correct trackpad supply
+    - arm64: dts: qcom: msm8994-kitakami: drop unit address from PMI8994 regulator
+    - arm64: dts: qcom: msm8994-msft-lumia-octagon: drop unit address from PMI8994
+      regulator
+    - drm/ttm: optimize pool allocations a bit v2
+    - drm/ttm/pool: Fix ttm_pool_alloc error path
+    - regulator: core: Consistently set mutex_owner when using
+      ww_mutex_lock_slow()
+    - regulator: core: Avoid lockdep reports when resolving supplies
+    - x86/apic: Fix atomic update of offset in reserve_eilvt_offset()
+    - media: rkvdec: fix use after free bug in rkvdec_remove
+    - media: dm1105: Fix use after free bug in dm1105_remove due to race condition
+    - media: saa7134: fix use after free bug in saa7134_finidev due to race
+      condition
+    - media: rcar_fdp1: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - media: rcar_fdp1: Fix the correct variable assignments
+    - platform: Provide a remove callback that returns no value
+    - media: rcar_fdp1: Convert to platform remove callback returning void
+    - media: rcar_fdp1: Fix refcount leak in probe and remove function
+    - drm/amd/display: Fix potential null dereference
+    - media: rc: gpio-ir-recv: Fix support for wake-up
+    - media: venus: dec: Fix handling of the start cmd
+    - regulator: stm32-pwr: fix of_iomap leak
+    - x86/ioapic: Don't return 0 from arch_dynirq_lower_bound()
+    - arm64: kgdb: Set PSTATE.SS to 1 to re-enable single-step
+    - debugobject: Prevent init race with static objects
+    - drm/i915: Make intel_get_crtc_new_encoder() less oopsy
+    - tick/common: Align tick period with the HZ tick.
+    - cpufreq: use correct unit when verify cur freq
+    - hwmon: (pmbus/fsp-3y) Fix functionality bitmask in FSP-3Y YM-2151E
+    - wifi: ath6kl: minor fix for allocation size
+    - wifi: ath9k: hif_usb: fix memory leak of remain_skbs
+    - wifi: ath5k: fix an off by one check in ath5k_eeprom_read_freq_list()
+    - wifi: brcmfmac: support CQM RSSI notification with older firmware
+    - wifi: ath6kl: reduce WARN to dev_dbg() in callback
+    - tools: bpftool: Remove invalid \' json escape
+    - wifi: rtw88: mac: Return the original error from rtw_pwr_seq_parser()
+    - wifi: rtw88: mac: Return the original error from rtw_mac_power_switch()
+    - bpf: take into account liveness when propagating precision
+    - bpf: fix precision propagation verbose logging
+    - scm: fix MSG_CTRUNC setting condition for SO_PASSSEC
+    - selftests/bpf: Fix a fd leak in an error path in network_helpers.c
+    - bpf: Remove misleading spec_v1 check on var-offset stack read
+    - net: pcs: xpcs: remove double-read of link state when using AN
+    - vlan: partially enable SIOCSHWTSTAMP in container
+    - net/packet: annotate accesses to po->xmit
+    - net/packet: convert po->origdev to an atomic flag
+    - net/packet: convert po->auxdata to an atomic flag
+    - scsi: target: Fix multiple LUN_RESET handling
+    - scsi: target: iscsit: Fix TAS handling during conn cleanup
+    - scsi: megaraid: Fix mega_cmd_done() CMDID_INT_CMDS
+    - f2fs: handle dqget error in f2fs_transfer_project_quota()
+    - f2fs: enforce single zone capacity
+    - f2fs: apply zone capacity to all zone type
+    - f2fs: compress: fix to call f2fs_wait_on_page_writeback() in
+      f2fs_write_raw_pages()
+    - crypto: caam - Clear some memory in instantiate_rng
+    - crypto: sa2ul - Select CRYPTO_DES
+    - wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_rfreg()
+    - wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_reg()
+    - wifi: rt2x00: Fix memory leak when handling surveys
+    - net: qrtr: correct types of trace event parameters
+    - selftests: xsk: Disable IPv6 on VETH1
+    - selftests/bpf: Wait for receive in cg_storage_multi test
+    - bpftool: Fix bug for long instructions in program CFG dumps
+    - crypto: drbg - make drbg_prepare_hrng() handle jent instantiation errors
+    - crypto: drbg - Only fail when jent is unavailable in FIPS mode
+    - xsk: Fix unaligned descriptor validation
+    - f2fs: fix to avoid use-after-free for cached IPU bio
+    - scsi: lpfc: Fix ioremap issues in lpfc_sli4_pci_mem_setup()
+    - net: ethernet: stmmac: dwmac-rk: fix optional phy regulator handling
+    - bpf, sockmap: fix deadlocks in the sockhash and sockmap
+    - nvmet: use i_size_read() to set size for file-ns
+    - nvmet: move the call to nvmet_ns_changed out of nvmet_ns_revalidate
+    - nvmet: fix error handling in nvmet_execute_identify_cns_cs_ns()
+    - nvmet: fix Identify Namespace handling
+    - nvmet: fix Identify Controller handling
+    - nvmet: fix Identify Active Namespace ID list handling
+    - nvmet: fix I/O Command Set specific Identify Controller
+    - nvme: handle the persistent internal error AER
+    - nvme: fix async event trace event
+    - nvme-fcloop: fix "inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage"
+    - selftests/bpf: Fix leaked bpf_link in get_stackid_cannot_attach
+    - bpf, sockmap: Revert buggy deadlock fix in the sockhash and sockmap
+    - md: drop queue limitation for RAID1 and RAID10
+    - md: raid10 add nowait support
+    - md/raid10: factor out code from wait_barrier() to stop_waiting_barrier()
+    - md/raid10: fix task hung in raid10d
+    - md/raid10: fix leak of 'r10bio->remaining' for recovery
+    - md/raid10: fix memleak for 'conf->bio_split'
+    - md/raid10: fix memleak of md thread
+    - md/raid10: don't call bio_start_io_acct twice for bio which experienced read
+      error
+    - wifi: iwlwifi: yoyo: skip dump correctly on hw error
+    - wifi: iwlwifi: yoyo: Fix possible division by zero
+    - wifi: iwlwifi: mvm: initialize seq variable
+    - wifi: iwlwifi: fw: move memset before early return
+    - jdb2: Don't refuse invalidation of already invalidated buffers
+    - wifi: iwlwifi: make the loop for card preparation effective
+    - wifi: mt76: handle failure of vzalloc in mt7615_coredump_work
+    - wifi: mt76: add flexible polling wait-interval support
+    - wifi: mt76: mt7921e: fix probe timeout after reboot
+    - wifi: mt76: fix 6GHz high channel not be scanned
+    - wifi: mt76: mt7921e: improve reliability of dma reset
+    - wifi: iwlwifi: mvm: check firmware response size
+    - wifi: iwlwifi: fw: fix memory leak in debugfs
+    - ixgbe: Allow flow hash to be set via ethtool
+    - ixgbe: Enable setting RSS table to default values
+    - net/mlx5: E-switch, Don't destroy indirect table in split rule
+    - net: stmmac:fix system hang when setting up tag_8021q VLAN for DSA ports
+    - bpf: Don't EFAULT for getsockopt with optval=NULL
+    - netfilter: nf_tables: don't write table validation state without mutex
+    - net/sched: sch_fq: fix integer overflow of "credit"
+    - ipv4: Fix potential uninit variable access bug in __ip_make_skb()
+    - netlink: Use copy_to_user() for optval in netlink_getsockopt().
+    - net: amd: Fix link leak when verifying config failed
+    - tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
+    - ipmi: ASPEED_BT_IPMI_BMC: select REGMAP_MMIO instead of depending on it
+    - drivers: staging: rtl8723bs: Fix locking in _rtw_join_timeout_handler()
+    - drivers: staging: rtl8723bs: Fix locking in rtw_scan_timeout_handler()
+    - pstore: Revert pmsg_lock back to a normal mutex
+    - usb: host: xhci-rcar: remove leftover quirk handling
+    - usb: dwc3: gadget: Change condition for processing suspend event
+    - serial: stm32: re-introduce an irq flag condition in usart_receive_chars
+    - serial: stm32: Re-assert RTS/DE GPIO in RS485 mode only if more data are
+      transmitted
+    - fpga: bridge: fix kernel-doc parameter description
+    - iio: light: max44009: add missing OF device matching
+    - serial: 8250_bcm7271: Fix arbitration handling
+    - spi: spi-imx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
+    - spi: imx: Don't skip cleanup in remove's error path
+    - usb: gadget: udc: renesas_usb3: Fix use after free bug in
+      renesas_usb3_remove due to race condition
+    - PCI: imx6: Install the fault handler only on compatible match
+    - ASoC: es8316: Handle optional IRQ assignment
+    - linux/vt_buffer.h: allow either builtin or modular for macros
+    - spi: qup: Don't skip cleanup in remove's error path
+    - spi: fsl-spi: Fix CPM/QE mode Litte Endian
+    - vmci_host: fix a race condition in vmci_host_poll() causing GPF
+    - of: Fix modalias string generation
+    - PCI/EDR: Clear Device Status after EDR error recovery
+    - ia64: mm/contig: fix section mismatch warning/error
+    - ia64: salinfo: placate defined-but-not-used warning
+    - scripts/gdb: bail early if there are no clocks
+    - scripts/gdb: bail early if there are no generic PD
+    - HID: amd_sfh: Add support for shutdown operation
+    - coresight: etm_pmu: Set the module field
+    - ASoC: fsl_mqs: move of_node_put() to the correct location
+    - spi: cadence-quadspi: fix suspend-resume implementations
+    - i2c: cadence: cdns_i2c_master_xfer(): Fix runtime PM leak on error path
+    - scripts/gdb: raise error with reduced debugging information
+    - uapi/linux/const.h: prefer ISO-friendly __typeof__
+    - sh: sq: Fix incorrect element size for allocating bitmap buffer
+    - usb: gadget: tegra-xudc: Fix crash in vbus_draw
+    - usb: chipidea: fix missing goto in `ci_hdrc_probe`
+    - usb: mtu3: fix kernel panic at qmu transfer done irq handler
+    - firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe
+    - tty: serial: fsl_lpuart: adjust buffer length to the intended size
+    - serial: 8250: Add missing wakeup event reporting
+    - staging: rtl8192e: Fix W_DISABLE# does not work after stop/start
+    - spmi: Add a check for remove callback when removing a SPMI driver
+    - virtio_ring: don't update event idx on get_buf
+    - macintosh/windfarm_smu_sat: Add missing of_node_put()
+    - powerpc/mpc512x: fix resource printk format warning
+    - powerpc/wii: fix resource printk format warnings
+    - powerpc/sysdev/tsi108: fix resource printk format warnings
+    - macintosh: via-pmu-led: requires ATA to be set
+    - powerpc/rtas: use memmove for potentially overlapping buffer copy
+    - sched/fair: Use __schedstat_set() in set_next_entity()
+    - sched: Make struct sched_statistics independent of fair sched class
+    - sched/fair: Fix inaccurate tally of ttwu_move_affine
+    - perf/core: Fix hardlockup failure caused by perf throttle
+    - Revert "objtool: Support addition to set CFA base"
+    - sched/rt: Fix bad task migration for rt tasks
+    - clk: at91: clk-sam9x60-pll: fix return value check
+    - RDMA/siw: Fix potential page_array out of range access
+    - RDMA/rdmavt: Delete unnecessary NULL check
+    - workqueue: Introduce show_one_worker_pool and show_one_workqueue.
+    - workqueue: Fix hung time report of worker pools
+    - rtc: omap: include header for omap_rtc_power_off_program prototype
+    - RDMA/mlx4: Prevent shift wrapping in set_user_sq_size()
+    - rtc: meson-vrtc: Use ktime_get_real_ts64() to get the current time
+    - fs/ntfs3: Fix memory leak if ntfs_read_mft failed
+    - fs/ntfs3: Add check for kmemdup
+    - fs/ntfs3: Fix OOB read in indx_insert_into_buffer
+    - fs/ntfs3: Fix slab-out-of-bounds read in hdr_delete_de()
+    - power: supply: generic-adc-battery: fix unit scaling
+    - clk: add missing of_node_put() in "assigned-clocks" property parsing
+    - RDMA/siw: Remove namespace check from siw_netdev_event()
+    - clk: qcom: gcc-sm6115: Mark RCGs shared where applicable
+    - RDMA/cm: Trace icm_send_rej event before the cm state is reset
+    - RDMA/srpt: Add a check for valid 'mad_agent' pointer
+    - IB/hfi1: Fix SDMA mmu_rb_node not being evicted in LRU order
+    - IB/hfi1: Fix bugs with non-PAGE_SIZE-end multi-iovec user SDMA requests
+    - NFSv4.1: Always send a RECLAIM_COMPLETE after establishing lease
+    - clk: qcom: regmap: add PHY clock source implementation
+    - clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
+    - Input: raspberrypi-ts - fix refcount leak in rpi_ts_probe
+    - RDMA/mlx5: Fix flow counter query via DEVX
+    - SUNRPC: remove the maximum number of retries in call_bind_status
+    - RDMA/mlx5: Use correct device num_ports when modify DC
+    - clocksource/drivers/davinci: Fix memory leak in davinci_timer_register when
+      init fails
+    - openrisc: Properly store r31 to pt_regs on unhandled exceptions
+    - timekeeping: Fix references to nonexistent ktime_get_fast_ns()
+    - SMB3: Add missing locks to protect deferred close file list
+    - SMB3: Close deferred file handles in case of handle lease break
+    - ext4: fix i_disksize exceeding i_size problem in paritally written case
+    - ext4: fix use-after-free read in ext4_find_extent for bigalloc + inline
+    - pinctrl: renesas: r8a779a0: Remove incorrect AVB[01] pinmux configuration
+    - leds: TI_LMU_COMMON: select REGMAP instead of depending on it
+    - dmaengine: mv_xor_v2: Fix an error code.
+    - leds: tca6507: Fix error handling of using fwnode_property_read_string
+    - pwm: mtk-disp: Disable shadow registers before setting backlight values
+    - pwm: mtk-disp: Configure double buffering before reading in .get_state()
+    - phy: tegra: xusb: Add missing tegra_xusb_port_unregister for usb2_port and
+      ulpi_port
+    - dma: gpi: remove spurious unlock in gpi_ch_init
+    - dmaengine: dw-edma: Fix to change for continuous transfer
+    - dmaengine: dw-edma: Fix to enable to issue dma request on DMA processing
+    - dmaengine: at_xdmac: Fix concurrency over chan's completed_cookie
+    - dmaengine: at_xdmac: Fix race for the tx desc callback
+    - dmaengine: at_xdmac: do not enable all cyclic channels
+    - thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in
+      mtk_thermal_probe
+    - mfd: tqmx86: Do not access I2C_DETECT register through io_base
+    - mfd: tqmx86: Specify IO port register range more precisely
+    - mfd: tqmx86: Correct board names for TQMxE39x
+    - afs: Fix updating of i_size with dv jump from server
+    - parisc: Fix argument pointer in real64_call_asm()
+    - ALSA: usb-audio: Add quirk for Pioneer DDJ-800
+    - nilfs2: do not write dirty data after degenerating to read-only
+    - nilfs2: fix infinite loop in nilfs_mdt_get_block()
+    - md/raid10: fix null-ptr-deref in raid10_sync_request
+    - mtd: core: provide unique name for nvmem device, take two
+    - mtd: core: fix nvmem error reporting
+    - mtd: core: fix error path for nvmem provider
+    - mailbox: zynqmp: Fix IPI isr handling
+    - mailbox: zynqmp: Fix typo in IPI documentation
+    - wifi: rtl8xxxu: RTL8192EU always needs full init
+    - clk: rockchip: rk3399: allow clk_cifout to force clk_cifout_src to reparent
+    - scripts/gdb: fix lx-timerlist for Python3
+    - btrfs: scrub: reject unsupported scrub flags
+    - s390/dasd: fix hanging blockdevice after request requeue
+    - ia64: fix an addr to taddr in huge_pte_offset()
+    - dm verity: fix error handling for check_at_most_once on FEC
+    - dm clone: call kmem_cache_destroy() in dm_clone_init() error path
+    - dm integrity: call kmem_cache_destroy() in dm_integrity_init() error path
+    - dm flakey: fix a crash with invalid table line
+    - dm ioctl: fix nested locking in table_clear() to remove deadlock concern
+    - dm: don't lock fs when the map is NULL in process of resume
+    - perf auxtrace: Fix address filter entire kernel size
+    - perf intel-pt: Fix CYC timestamps after standalone CBR
+    - sound/oss/dmasound: fix 'dmasound_setup' defined but not used
+    - arm64: dts: qcom: sdm845: correct dynamic power coefficients - again
+    - sched: Fix DEBUG && !SCHEDSTATS warn
+    - Linux 5.15.111
+
+  * Jammy update: v5.15.110 upstream stable release (LP: #2025090)
+    - PCI/ASPM: Remove pcie_aspm_pm_state_change()
+    - selftests/kselftest/runner/run_one(): allow running non-executable files
+    - KVM: arm64: Retry fault if vma_lookup() results become invalid
+    - KVM: arm64: Fix buffer overflow in kvm_arm_set_fw_reg()
+    - drm/fb-helper: set x/yres_virtual in drm_fb_helper_check_var
+    - bluetooth: Perform careful capability checks in hci_sock_ioctl()
+    - USB: serial: option: add UNISOC vendor and TOZED LT70C product
+    - driver core: Don't require dynamic_debug for initcall_debug probe timing
+    - selftests: mptcp: join: fix "invalid address, ADD_ADDR timeout"
+    - riscv: Move early dtb mapping into the fixmap region
+    - riscv: Do not set initial_boot_params to the linear address of the dtb
+    - riscv: No need to relocate the dtb as it lies in the fixmap region
+    - Linux 5.15.110
+
+  * Jammy update: v5.15.109 upstream stable release (LP: #2024265)
+    - ARM: dts: rockchip: fix a typo error for rk3288 spdif node
+    - arm64: dts: qcom: ipq8074-hk01: enable QMP device, not the PHY node
+    - arm64: dts: meson-g12-common: specify full DMC range
+    - arm64: dts: imx8mm-evk: correct pmic clock source
+    - netfilter: br_netfilter: fix recent physdev match breakage
+    - regulator: fan53555: Explicitly include bits header
+    - regulator: fan53555: Fix wrong TCS_SLEW_MASK
+    - virtio_net: bugfix overflow inside xdp_linearize_page()
+    - sfc: Split STATE_READY in to STATE_NET_DOWN and STATE_NET_UP.
+    - sfc: Fix use-after-free due to selftest_work
+    - netfilter: nf_tables: fix ifdef to also consider nf_tables=m
+    - i40e: fix accessing vsi->active_filters without holding lock
+    - i40e: fix i40e_setup_misc_vector() error handling
+    - netfilter: nf_tables: validate catch-all set elements
+    - netfilter: nf_tables: tighten netlink attribute requirements for catch-all
+      elements
+    - bnxt_en: Do not initialize PTP on older P3/P4 chips
+    - mlxfw: fix null-ptr-deref in mlxfw_mfa2_tlv_next()
+    - bonding: Fix memory leak when changing bond type to Ethernet
+    - net: rpl: fix rpl header size calculation
+    - mlxsw: pci: Fix possible crash during initialization
+    - spi: spi-rockchip: Fix missing unwind goto in rockchip_sfc_probe()
+    - bpf: Fix incorrect verifier pruning due to missing register precision taints
+    - e1000e: Disable TSO on i219-LM card to increase speed
+    - f2fs: Fix f2fs_truncate_partial_nodes ftrace event
+    - Input: i8042 - add quirk for Fujitsu Lifebook A574/H
+    - platform/x86 (gigabyte-wmi): Add support for A320M-S2H V2
+    - selftests: sigaltstack: fix -Wuninitialized
+    - scsi: megaraid_sas: Fix fw_crash_buffer_show()
+    - scsi: core: Improve scsi_vpd_inquiry() checks
+    - net: dsa: b53: mmap: add phy ops
+    - s390/ptrace: fix PTRACE_GET_LAST_BREAK error handling
+    - nvme-tcp: fix a possible UAF when failing to allocate an io queue
+    - xen/netback: use same error messages for same errors
+    - platform/x86: gigabyte-wmi: add support for X570S AORUS ELITE
+    - rtmutex: Add acquire semantics for rtmutex lock acquisition slow path
+    - iio: light: tsl2772: fix reading proximity-diodes from device tree
+    - nilfs2: initialize unused bytes in segment summary blocks
+    - memstick: fix memory leak if card device is never registered
+    - kernel/sys.c: fix and improve control flow in __sys_setres[ug]id()
+    - mmc: sdhci_am654: Set HIGH_SPEED_ENA for SDR12 and SDR25
+    - drm/i915: Fix fast wake AUX sync len
+    - mm/khugepaged: check again on anon uffd-wp during isolation
+    - mm: page_alloc: skip regions with hugetlbfs pages when allocating 1G pages
+    - sched/uclamp: Fix fits_capacity() check in feec()
+    - sched/uclamp: Make cpu_overutilized() use util_fits_cpu()
+    - sched/uclamp: Cater for uclamp in find_energy_efficient_cpu()'s early exit
+      condition
+    - sched/fair: Detect capacity inversion
+    - sched/fair: Consider capacity inversion in util_fits_cpu()
+    - sched/uclamp: Fix a uninitialized variable warnings
+    - sched/fair: Fixes for capacity inversion detection
+    - MIPS: Define RUNTIME_DISCARD_EXIT in LD script
+    - docs: futex: Fix kernel-doc references after code split-up preparation
+    - purgatory: fix disabling debug info
+    - fuse: fix attr version comparison in fuse_read_update_size()
+    - fuse: always revalidate rename target dentry
+    - fuse: fix deadlock between atomic O_TRUNC and page invalidation
+    - udp: Call inet6_destroy_sock() in setsockopt(IPV6_ADDRFORM).
+    - tcp/udp: Call inet6_destroy_sock() in IPv6 sk->sk_destruct().
+    - inet6: Remove inet6_destroy_sock() in sk->sk_prot->destroy().
+    - dccp: Call inet6_destroy_sock() via sk->sk_destruct().
+    - sctp: Call inet6_destroy_sock() via sk->sk_destruct().
+    - pwm: meson: Explicitly set .polarity in .get_state()
+    - pwm: iqs620a: Explicitly set .polarity in .get_state()
+    - pwm: hibvt: Explicitly set .polarity in .get_state()
+    - counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
+    - iio: adc: at91-sama5d2_adc: fix an error code in at91_adc_allocate_trigger()
+    - mm/page_alloc: fix potential deadlock on zonelist_update_seq seqlock
+    - ASoC: fsl_asrc_dma: fix potential null-ptr-deref
+    - ASN.1: Fix check for strdup() success
+    - soc: sifive: l2_cache: fix missing iounmap() in error path in
+      sifive_l2_init()
+    - soc: sifive: l2_cache: fix missing free_irq() in error path in
+      sifive_l2_init()
+    - soc: sifive: l2_cache: fix missing of_node_put() in sifive_l2_init()
+    - Linux 5.15.109
+
+  * Disable hv-kvp-daemon if /dev/vmbus/hv_kvp is not present (LP: #2024900)
+    - [Packaging] disable hv-kvp-daemon if needed
+
+  * A deadlock issue in scsi rescan task while resuming from S3 (LP: #2018566)
+    - ata: libata-scsi: Avoid deadlock on rescan after device resume
+
+  * [SRU] Intel Sapphire Rapids HBM support needs CONFIG_NUMA_EMU (LP: #2008745)
+    - [Config] Intel Sapphire Rapids HBM support needs CONFIG_NUMA_EMU
+
+  * [22.04 FEAT] Enhanced Interpretation for PCI Functions on s390x - kernel
+    part (LP: #1853306)
+    - kvm: use kvfree() in kvm_arch_free_vm()
+    - s390/sclp: add detection of IPL-complete-control facility
+    - s390/pci: use phys_to_virt() for AIBVs/DIBVs
+    - s390/sclp: detect the zPCI load/store interpretation facility
+    - s390/sclp: detect the AISII facility
+    - s390/sclp: detect the AENI facility
+    - s390/sclp: detect the AISI facility
+    - s390/airq: pass more TPI info to airq handlers
+    - s390/airq: allow for airq structure that uses an input vector
+    - s390/pci: externalize the SIC operation controls and routine
+    - s390/pci: stash associated GISA designation
+    - s390/pci: stash dtsm and maxstbl
+    - vfio/pci: introduce CONFIG_VFIO_PCI_ZDEV_KVM
+    - KVM: s390: pci: add basic kvm_zdev structure
+    - KVM: s390: pci: do initial setup for AEN interpretation
+    - KVM: s390: pci: enable host forwarding of Adapter Event Notifications
+    - KVM: s390: mechanism to enable guest zPCI Interpretation
+    - KVM: s390: pci: provide routines for enabling/disabling interrupt forwarding
+    - KVM: s390: pci: add routines to start/stop interpretive execution
+    - vfio-pci/zdev: add open/close device hooks
+    - vfio-pci/zdev: add function handle to clp base capability
+    - vfio-pci/zdev: different maxstbl for interpreted devices
+    - KVM: s390: add KVM_S390_ZPCI_OP to manage guest zPCI devices
+    - MAINTAINERS: additional files related kvm s390 pci passthrough
+    - Documentation: kvm: extend KVM_S390_ZPCI_OP subheading underline
+    - KVM: s390: pci: Hook to access KVM lowlevel from VFIO
+    - KVM: s390: pci: fix plain integer as NULL pointer warnings
+    - KVM: s390: pci: fix GAIT physical vs virtual pointers usage
+    - KVM: s390: pci: register pci hooks without interpretation
+    - [Config] enable VFIO zPCI pass-through for s390x
+
+  * Undefined Behavior Sanitizer (UBSAN) causes failure to match symbols
+    (LP: #2003374)
+    - [Config] s390x: Re-adding UBSAN to configuration
+
+  * CVE-2023-35001
+    - netfilter: nf_tables: prevent OOB access in nft_byteorder_eval
+
+  * CVE-2023-31248
+    - netfilter: nf_tables: do not ignore genmask when looking up chain by id
+
+  * CVE-2023-3389
+    - io_uring: hold uring mutex around poll removal
+
+  * CVE-2023-3439
+    - mctp: Add refcounts to mctp_dev
+    - mctp: Allow MCTP on tun devices
+    - mctp: make __mctp_dev_get() take a refcount hold
+    - mctp: defer the kfree of object mdev->addrs
+
+  * CVE-2023-3390
+    - netfilter: nf_tables: incorrect error path handling with NFT_MSG_NEWRULE
+
+  * CVE-2023-3141
+    - memstick: r592: Fix UAF bug in r592_remove due to race condition
+
+  * CVE-2023-3090
+    - ipvlan:Fix out-of-bounds caused by unclear skb->cb
+
+  * CVE-2022-48502
+    - fs/ntfs3: Check fields while reading
+
+  * ftrace in ubuntu_kernel_selftests failed with "check if duplicate events are
+    caught" on J-5.15 P9 / J-kvm / L-kvm (LP: #1977827)
+    - SAUCE: selftests/ftrace: Add test dependency
+
+  * Add microphone support of the front headphone port on P3 Tower
+    (LP: #2023650)
+    - ALSA: hda/realtek: Add Lenovo P3 Tower platform
+
+  * Add audio support for ThinkPad P1 Gen 6 and Z16 Gen 2 (LP: #2023539)
+    - ALSA: hda/realtek: Add quirks for Lenovo Z13/Z16 Gen2
+    - ALSA: hda/realtek: Add quirk for ThinkPad P1 Gen 6
+
+  * Resolve synchronous exception on arm64 (LP: #2023311)
+    - arm64: efi: Recover from synchronous exceptions occurring in firmware
+
+  * Enable Tracing Configs for OSNOISE and TIMERLAT (LP: #2018591)
+    - [Config] Enable OSNOISE_TRACER and TIMERLAT_TRACER configs
+
+  * Severe NFS performance degradation after LP #2003053 (LP: #2022098)
+    - SAUCE: Make NFS file-access stale cache behaviour opt-in
+
+  * Encountering an issue with memcpy_fromio causing failed boot of SEV-enabled
+    guest (LP: #2020319)
+    - x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
+
+  * linux-*: please enable dm-verity kconfigs to allow MoK/db verified root
+    images (LP: #2019040)
+    - [Config] CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG_SECONDARY_KEYRING=y
+
+  * CVE-2023-2124
+    - xfs: verify buffer contents when we skip log replay
+
+  * CVE-2023-0597
+    - x86/kasan: Map shadow for percpu pages on demand
+    - x86/mm: Randomize per-cpu entry area
+    - x86/mm: Recompute physical address for every page of per-CPU CEA mapping
+    - x86/mm: Populate KASAN shadow for entire per-CPU range of CPU entry area
+    - x86/mm: Do not shuffle CPU entry areas without KASLR
+
+  * Jammy update: v5.15.108 upstream stable release (LP: #2023328)
+    - Revert "pinctrl: amd: Disable and mask interrupts on resume"
+    - ALSA: emu10k1: fix capture interrupt handler unlinking
+    - ALSA: hda/sigmatel: add pin overrides for Intel DP45SG motherboard
+    - ALSA: i2c/cs8427: fix iec958 mixer control deactivation
+    - ALSA: firewire-tascam: add missing unwind goto in
+      snd_tscm_stream_start_duplex()
+    - ALSA: emu10k1: don't create old pass-through playback device on Audigy
+    - ALSA: hda/sigmatel: fix S/PDIF out on Intel D*45* motherboards
+    - Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
+    - Bluetooth: Fix race condition in hidp_session_thread
+    - btrfs: print checksum type and implementation at mount time
+    - btrfs: fix fast csum implementation detection
+    - fbmem: Reject FB_ACTIVATE_KD_TEXT from userspace
+    - mtdblock: tolerate corrected bit-flips
+    - mtd: rawnand: meson: fix bitmask for length in command word
+    - mtd: rawnand: stm32_fmc2: remove unsupported EDO mode
+    - mtd: rawnand: stm32_fmc2: use timings.mode instead of checking tRC_min
+    - KVM: arm64: PMU: Restore the guest's EL0 event counting after migration
+    - drm/i915/dsi: fix DSS CTL register offsets for TGL+
+    - clk: sprd: set max_register according to mapping range
+    - RDMA/irdma: Fix memory leak of PBLE objects
+    - RDMA/irdma: Increase iWARP CM default rexmit count
+    - RDMA/irdma: Add ipv4 check to irdma_find_listener()
+    - IB/mlx5: Add support for 400G_8X lane speed
+    - RDMA/cma: Allow UD qp_type to join multicast only
+    - bpf: tcp: Use sock_gen_put instead of sock_put in bpf_iter_tcp
+    - niu: Fix missing unwind goto in niu_alloc_channels()
+    - tcp: restrict net.ipv4.tcp_app_win
+    - drm/armada: Fix a potential double free in an error handling path
+    - qlcnic: check pci_reset_function result
+    - net: qrtr: Fix an uninit variable access bug in qrtr_tx_resume()
+    - sctp: fix a potential overflow in sctp_ifwdtsn_skip
+    - RDMA/core: Fix GID entry ref leak when create_ah fails
+    - udp6: fix potential access to stale information
+    - net: macb: fix a memory corruption in extended buffer descriptor mode
+    - skbuff: Fix a race between coalescing and releasing SKBs
+    - libbpf: Fix single-line struct definition output in btf_dump
+    - ARM: 9290/1: uaccess: Fix KASAN false-positives
+    - power: supply: cros_usbpd: reclassify "default case!" as debug
+    - wifi: mwifiex: mark OF related data as maybe unused
+    - i2c: imx-lpi2c: clean rx/tx buffers upon new message
+    - i2c: hisi: Avoid redundant interrupts
+    - efi: sysfb_efi: Add quirk for Lenovo Yoga Book X91F/L
+    - drm: panel-orientation-quirks: Add quirk for Lenovo Yoga Book X90F
+    - verify_pefile: relax wrapper length check
+    - asymmetric_keys: log on fatal failures in PE/pkcs7
+    - wifi: iwlwifi: mvm: fix mvmtxq->stopped handling
+    - ACPI: resource: Add Medion S17413 to IRQ override quirk
+    - counter: stm32-lptimer-cnt: Provide defines for clock polarities
+    - counter: stm32-timer-cnt: Provide defines for slave mode selection
+    - counter: Internalize sysfs interface code
+    - counter: 104-quad-8: Fix Synapse action reported for Index signals
+    - tracing: Add trace_array_puts() to write into instance
+    - tracing: Have tracing_snapshot_instance_cond() write errors to the
+      appropriate instance
+    - i915/perf: Replace DRM_DEBUG with driver specific drm_dbg call
+    - drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
+    - riscv: add icache flush for nommu sigreturn trampoline
+    - net: sfp: initialize sfp->i2c_block_size at sfp allocation
+    - net: phy: nxp-c45-tja11xx: add remove callback
+    - net: phy: nxp-c45-tja11xx: fix unsigned long multiplication overflow
+    - scsi: ses: Handle enclosure with just a primary component gracefully
+    - x86/PCI: Add quirk for AMD XHCI controller that loses MSI-X state in D3hot
+    - cgroup/cpuset: Wake up cpuset_attach_wq tasks in cpuset_cancel_attach()
+    - mptcp: use mptcp_schedule_work instead of open-coding it
+    - mptcp: stricter state check in mptcp_worker
+    - ubi: Fix failure attaching when vid_hdr offset equals to (sub)page size
+    - ubi: Fix deadlock caused by recursively holding work_sem
+    - powerpc/papr_scm: Update the NUMA distance table for the target node
+    - sched/fair: Move calculate of avg_load to a better location
+    - sched/fair: Fix imbalance overflow
+    - x86/rtc: Remove __init for runtime functions
+    - i2c: ocores: generate stop condition after timeout in polling mode
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S50
+    - nvme-pci: avoid the deepest sleep state on ZHITAI TiPro7000 SSDs
+    - nvme-pci: Crucial P2 has bogus namespace ids
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM610
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM760
+    - nvme-pci: mark Lexar NM760 as IGNORE_DEV_SUBNQN
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD
+    - kexec: turn all kexec_mutex acquisitions into trylocks
+    - panic, kexec: make __crash_kexec() NMI safe
+    - counter: fix docum. build problems after filename change
+    - counter: Add the necessary colons and indents to the comments of
+      counter_compi
+    - nvme-pci: avoid the deepest sleep state on ZHITAI TiPro5000 SSDs
+    - Linux 5.15.108
+
+  * Jammy update: v5.15.107 upstream stable release (LP: #2023320)
+    - ocfs2: ocfs2_mount_volume does cleanup job before return error
+    - ocfs2: rewrite error handling of ocfs2_fill_super
+    - ocfs2: fix memory leak in ocfs2_mount_volume()
+    - NFSD: Fix sparse warning
+    - NFSD: pass range end to vfs_fsync_range() instead of count
+    - RDMA/irdma: Do not request 2-level PBLEs for CQ alloc
+    - platform/x86: int3472: Split into 2 drivers
+    - [Config] updateconfigs for Intel skl_int3472 driver split
+    - platform/x86: int3472/discrete: Ensure the clk/power enable pins are in
+      output mode
+    - iavf: return errno code instead of status code
+    - iavf/iavf_main: actually log ->src mask when talking about it
+    - serial: 8250_exar: derive nr_ports from PCI ID for Acces I/O cards
+    - serial: exar: Add support for Sealevel 7xxxC serial cards
+    - bpf: hash map, avoid deadlock with suitable hash mask
+    - gpio: GPIO_REGMAP: select REGMAP instead of depending on it
+    - Drivers: vmbus: Check for channel allocation before looking up relids
+    - pwm: cros-ec: Explicitly set .polarity in .get_state()
+    - pwm: sprd: Explicitly set .polarity in .get_state()
+    - KVM: s390: pv: fix external interruption loop not always detected
+    - wifi: mac80211: fix invalid drv_sta_pre_rcu_remove calls for non-uploaded
+      sta
+    - net: qrtr: combine nameservice into main module
+    - [Config] updateconfigs for ns module merger
+    - net: qrtr: Fix a refcount bug in qrtr_recvmsg()
+    - NFSD: Avoid calling OPDESC() with ops->opnum == OP_ILLEGAL
+    - icmp: guard against too small mtu
+    - net: don't let netpoll invoke NAPI if in xmit context
+    - net: dsa: mv88e6xxx: Reset mv88e6393x force WD event bit
+    - sctp: check send stream number after wait_for_sndbuf
+    - net: qrtr: Do not do DEL_SERVER broadcast after DEL_CLIENT
+    - ipv6: Fix an uninit variable access bug in __ip6_make_skb()
+    - platform/x86: think-lmi: Fix memory leak when showing current settings
+    - platform/x86: think-lmi: Fix memory leaks when parsing ThinkStation WMI
+      strings
+    - platform/x86: think-lmi: Clean up display of current_value on Thinkstation
+    - gpio: davinci: Add irq chip flag to skip set wake
+    - net: ethernet: ti: am65-cpsw: Fix mdio cleanup in probe
+    - net: stmmac: fix up RX flow hash indirection table when setting channels
+    - sunrpc: only free unix grouplist after RCU settles
+    - NFSD: callback request does not use correct credential for AUTH_SYS
+    - ice: fix wrong fallback logic for FDIR
+    - ice: Reset FDIR counter in FDIR init stage
+    - ethtool: reset #lanes when lanes is omitted
+    - gve: Secure enough bytes in the first TX desc for all TCP pkts
+    - kbuild: refactor single builds of *.ko
+    - usb: xhci: tegra: fix sleep in atomic call
+    - xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
+    - usb: cdnsp: Fixes error: uninitialized symbol 'len'
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-S
+    - USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs
+    - usb: typec: altmodes/displayport: Fix configure initial pin assignment
+    - USB: serial: option: add Telit FE990 compositions
+    - USB: serial: option: add Quectel RM500U-CN modem
+    - iio: adis16480: select CONFIG_CRC32
+    - iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
+    - iio: dac: cio-dac: Fix max DAC write value check for 12-bit
+    - iio: light: cm32181: Unregister second I2C client if present
+    - tty: serial: sh-sci: Fix transmit end interrupt handler
+    - tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
+    - tty: serial: fsl_lpuart: avoid checking for transfer complete when
+      UARTCTRL_SBK is asserted in lpuart32_tx_empty
+    - nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread()
+    - nilfs2: fix sysfs interface lifetime
+    - dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
+    - ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN
+    - ALSA: hda/realtek: Add quirk for Clevo X370SNW
+    - coresight: etm4x: Do not access TRCIDR1 for identification
+    - coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
+    - iio: adc: ad7791: fix IRQ flags
+    - scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
+    - scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
+    - smb3: allow deferred close timeout to be configurable
+    - smb3: lower default deferred close timeout to address perf regression
+    - cifs: sanitize paths in cifs_update_super_prepath.
+    - perf/core: Fix the same task check in perf_event_set_output
+    - ftrace: Mark get_lock_parent_ip() __always_inline
+    - ftrace: Fix issue that 'direct->addr' not restored in modify_ftrace_direct()
+    - fs: drop peer group ids under namespace lock
+    - can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
+    - can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
+    - tracing: Free error logs of tracing instances
+    - ASoC: hdac_hdmi: use set_stream() instead of set_tdm_slots()
+    - mm: vmalloc: avoid warn_alloc noise caused by fatal signal
+    - drm/panfrost: Fix the panfrost_mmu_map_fault_addr() error path
+    - drm/nouveau/disp: Support more modes by checking with lower bpc
+    - ring-buffer: Fix race while reader and writer are on the same page
+    - mm/swap: fix swap_info_struct race between swapoff and get_swap_pages()
+    - drm/bridge: lt9611: Fix PLL being unable to lock
+    - mm: take a page reference when removing device exclusive entries
+    - kbuild: fix single directory build
+    - ocfs2: fix freeing uninitialized resource on ocfs2_dlm_shutdown
+    - bpftool: Print newline before '}' for struct with padding only fields
+    - Linux 5.15.107
+
+  * Jammy update: v5.15.106 upstream stable release (LP: #2023233)
+    - fsverity: don't drop pagecache at end of FS_IOC_ENABLE_VERITY
+    - usb: dwc3: gadget: move cmd_endtransfer to extra function
+    - usb: dwc3: gadget: Add 1ms delay after end transfer command without IOC
+    - kernel: kcsan: kcsan_test: build without structleak plugin
+    - kcsan: avoid passing -g for test
+    - ksmbd: don't terminate inactive sessions after a few seconds
+    - bus: imx-weim: fix branch condition evaluates to a garbage value
+    - xfrm: Zero padding when dumping algos and encap
+    - ASoC: codecs: tx-macro: Fix for KASAN: slab-out-of-bounds
+    - md: avoid signed overflow in slot_store()
+    - x86/PVH: obtain VGA console info in Dom0
+    - net: hsr: Don't log netdev_err message on unknown prp dst node
+    - ALSA: asihpi: check pao in control_message()
+    - ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
+    - fbdev: tgafb: Fix potential divide by zero
+    - sched_getaffinity: don't assume 'cpumask_size()' is fully initialized
+    - fbdev: nvidia: Fix potential divide by zero
+    - fbdev: intelfb: Fix potential divide by zero
+    - fbdev: lxfb: Fix potential divide by zero
+    - fbdev: au1200fb: Fix potential divide by zero
+    - tools/power turbostat: Fix /dev/cpu_dma_latency warnings
+    - tools/power turbostat: fix decoding of HWP_STATUS
+    - tracing: Fix wrong return in kprobe_event_gen_test.c
+    - ca8210: Fix unsigned mac_len comparison with zero in ca8210_skb_tx()
+    - mips: bmips: BCM6358: disable RAC flush for TP1
+    - ALSA: usb-audio: Fix recursive locking at XRUN during syncing
+    - platform/x86: think-lmi: add missing type attribute
+    - platform/x86: think-lmi: use correct possible_values delimiters
+    - platform/x86: think-lmi: only display possible_values if available
+    - platform/x86: think-lmi: Add possible_values for ThinkStation
+    - mtd: rawnand: meson: invalidate cache on polling ECC bit
+    - SUNRPC: fix shutdown of NFS TCP client socket
+    - sfc: ef10: don't overwrite offload features at NIC reset
+    - scsi: megaraid_sas: Fix crash after a double completion
+    - scsi: mpt3sas: Don't print sense pool info twice
+    - ptp_qoriq: fix memory leak in probe()
+    - net: dsa: microchip: ksz8863_smi: fix bulk access
+    - r8169: fix RTL8168H and RTL8107E rx crc error
+    - regulator: Handle deferred clk
+    - net/net_failover: fix txq exceeding warning
+    - net: stmmac: don't reject VLANs when IFF_PROMISC is set
+    - drm/i915/tc: Fix the ICL PHY ownership check in TC-cold state
+    - platform/x86/intel/pmc: Alder Lake PCH slp_s0_residency fix
+    - can: bcm: bcm_tx_setup(): fix KMSAN uninit-value in vfs_write
+    - s390/vfio-ap: fix memory leak in vfio_ap device driver
+    - loop: suppress uevents while reconfiguring the device
+    - loop: LOOP_CONFIGURE: send uevents for partitions
+    - net: mvpp2: classifier flow fix fragmentation flags
+    - net: mvpp2: parser fix QinQ
+    - net: mvpp2: parser fix PPPoE
+    - smsc911x: avoid PHY being resumed when interface is not up
+    - ice: add profile conflict check for AVF FDIR
+    - ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
+    - ALSA: ymfpci: Create card with device-managed snd_devm_card_new()
+    - ALSA: ymfpci: Fix BUG_ON in probe function
+    - net: ipa: compute DMA pool size properly
+    - i40e: fix registers dump after run ethtool adapter self test
+    - bnxt_en: Fix reporting of test result in ethtool selftest
+    - bnxt_en: Fix typo in PCI id to device description string mapping
+    - bnxt_en: Add missing 200G link speed reporting
+    - net: dsa: mv88e6xxx: Enable IGMP snooping on user ports only
+    - net: ethernet: mtk_eth_soc: fix flow block refcounting logic
+    - pinctrl: ocelot: Fix alt mode for ocelot
+    - iommu/vt-d: Allow zero SAGAW if second-stage not supported
+    - Input: alps - fix compatibility with -funsigned-char
+    - Input: focaltech - use explicitly signed char type
+    - cifs: prevent infinite recursion in CIFSGetDFSRefer()
+    - cifs: fix DFS traversal oops without CONFIG_CIFS_DFS_UPCALL
+    - Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table
+    - btrfs: fix race between quota disable and quota assign ioctls
+    - btrfs: scan device in non-exclusive mode
+    - zonefs: Always invalidate last cached page on append write
+    - can: j1939: prevent deadlock by moving j1939_sk_errqueue()
+    - xen/netback: don't do grant copy across page boundary
+    - net: phy: dp83869: fix default value for tx-/rx-internal-delay
+    - pinctrl: amd: Disable and mask interrupts on resume
+    - pinctrl: at91-pio4: fix domain name assignment
+    - powerpc: Don't try to copy PPR for task with NULL pt_regs
+    - NFSv4: Fix hangs when recovering open state after a server reboot
+    - ALSA: hda/conexant: Partial revert of a quirk for Lenovo
+    - ALSA: usb-audio: Fix regression on detection of Roland VS-100
+    - ALSA: hda/realtek: Add quirks for some Clevo laptops
+    - ALSA: hda/realtek: Add quirk for Lenovo ZhaoYang CF4620Z
+    - xtensa: fix KASAN report for show_stack
+    - rcu: Fix rcu_torture_read ftrace event
+    - drm/etnaviv: fix reference leak when mmaping imported buffer
+    - drm/amd/display: Add DSC Support for Synaptics Cascaded MST Hub
+    - KVM: arm64: Disable interrupts while walking userspace PTs
+    - KVM: VMX: Move preemption timer <=> hrtimer dance to common x86
+    - KVM: x86: Inject #GP on x2APIC WRMSR that sets reserved bits 63:32
+    - KVM: x86: Purge "highest ISR" cache when updating APICv state
+    - zonefs: Fix error message in zonefs_file_dio_append()
+    - selftests/bpf: Test btf dump for struct with padding only fields
+    - libbpf: Fix BTF-to-C converter's padding logic
+    - selftests/bpf: Add few corner cases to test padding handling of btf_dump
+    - libbpf: Fix btf_dump's packed struct determination
+    - hsr: ratelimit only when errors are printed
+    - x86/PVH: avoid 32-bit build warning when obtaining VGA console info
+    - Linux 5.15.106
+
+  * Jammy update: v5.15.105 upstream stable release (LP: #2023230)
+    - interconnect: qcom: osm-l3: fix icc_onecell_data allocation
+    - perf/core: Fix perf_output_begin parameter is incorrectly invoked in
+      perf_event_bpf_output
+    - perf: fix perf_event_context->time
+    - tracing/hwlat: Replace sched_setaffinity with set_cpus_allowed_ptr
+    - serial: fsl_lpuart: Fix comment typo
+    - tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
+    - tty: serial: fsl_lpuart: fix race on RX DMA shutdown
+    - serial: 8250: SERIAL_8250_ASPEED_VUART should depend on ARCH_ASPEED
+    - [Config] updateconfigs for SERIAL_8250_ASPEED_VUART
+    - serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
+    - kthread: add the helper function kthread_run_on_cpu()
+    - trace/hwlat: make use of the helper function kthread_run_on_cpu()
+    - trace/hwlat: Do not start per-cpu thread if it is already running
+    - net: tls: fix possible race condition between do_tls_getsockopt_conf() and
+      do_tls_setsockopt_conf()
+    - power: supply: bq24190_charger: using pm_runtime_resume_and_get instead of
+      pm_runtime_get_sync
+    - power: supply: bq24190: Fix use after free bug in bq24190_remove due to race
+      condition
+    - power: supply: da9150: Fix use after free bug in da9150_charger_remove due
+      to race condition
+    - ARM: dts: imx6sll: e60k02: fix usbotg1 pinctrl
+    - ARM: dts: imx6sl: tolino-shine2hd: fix usbotg1 pinctrl
+    - arm64: dts: imx8mn: specify #sound-dai-cells for SAI nodes
+    - xsk: Add missing overflow check in xdp_umem_reg
+    - iavf: fix inverted Rx hash condition leading to disabled hash
+    - iavf: fix non-tunneled IPv6 UDP packet type and hashing
+    - intel/igbvf: free irq on the error path in igbvf_request_msix()
+    - igbvf: Regard vf reset nack as success
+    - igc: fix the validation logic for taprio's gate list
+    - i2c: imx-lpi2c: check only for enabled interrupt flags
+    - i2c: hisi: Only use the completion interrupt to finish the transfer
+    - scsi: scsi_dh_alua: Fix memleak for 'qdata' in alua_activate()
+    - net: dsa: b53: mmap: fix device tree support
+    - net: usb: smsc95xx: Limit packet length to skb->len
+    - qed/qed_sriov: guard against NULL derefs from qed_iov_get_vf_info
+    - net: phy: Ensure state transitions are processed from phy_stop()
+    - net: mdio: fix owner field for mdio buses registered using device-tree
+    - net: mdio: fix owner field for mdio buses registered using ACPI
+    - drm/i915/gt: perform uc late init after probe error injection
+    - net: qcom/emac: Fix use after free bug in emac_remove due to race condition
+    - net/ps3_gelic_net: Fix RX sk_buff length
+    - net/ps3_gelic_net: Use dma_mapping_error
+    - octeontx2-vf: Add missing free for alloc_percpu
+    - bootconfig: Fix testcase to increase max node
+    - keys: Do not cache key in task struct if key is requested from kernel thread
+    - iavf: fix hang on reboot with ice
+    - i40e: fix flow director packet filter programming
+    - bpf: Adjust insufficient default bpf_jit_limit
+    - net/mlx5e: Set uplink rep as NETNS_LOCAL
+    - net/mlx5: Fix steering rules cleanup
+    - net/mlx5: Read the TC mapping of all priorities on ETS query
+    - net/mlx5: E-Switch, Fix an Oops in error handling code
+    - net: dsa: tag_brcm: legacy: fix daisy-chained switches
+    - atm: idt77252: fix kmemleak when rmmod idt77252
+    - erspan: do not use skb_mac_header() in ndo_start_xmit()
+    - net/sonic: use dma_mapping_error() for error check
+    - nvme-tcp: fix nvme_tcp_term_pdu to match spec
+    - hvc/xen: prevent concurrent accesses to the shared ring
+    - ksmbd: add low bound validation to FSCTL_SET_ZERO_DATA
+    - ksmbd: add low bound validation to FSCTL_QUERY_ALLOCATED_RANGES
+    - ksmbd: fix possible refcount leak in smb2_open()
+    - gve: Cache link_speed value from device
+    - net: dsa: mt7530: move enabling disabling core clock to mt7530_pll_setup()
+    - net: dsa: mt7530: move lowering TRGMII driving to mt7530_setup()
+    - net: dsa: mt7530: move setting ssc_delta to PHY_INTERFACE_MODE_TRGMII case
+    - net: mdio: thunder: Add missing fwnode_handle_put()
+    - Bluetooth: btqcomsmd: Fix command timeout after setting BD address
+    - Bluetooth: L2CAP: Fix responding with wrong PDU type
+    - platform/chrome: cros_ec_chardev: fix kernel data leak from ioctl
+    - thread_info: Add helpers to snapshot thread flags
+    - entry: Snapshot thread flags
+    - entry/rcu: Check TIF_RESCHED _after_ delayed RCU wake-up
+    - hwmon: fix potential sensor registration fail if of_node is missing
+    - hwmon (it87): Fix voltage scaling for chips with 10.9mV ADCs
+    - scsi: qla2xxx: Synchronize the IOCB count to be in order
+    - scsi: qla2xxx: Perform lockless command completion in abort path
+    - uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS583Gen 2
+    - thunderbolt: Use scale field when allocating USB3 bandwidth
+    - thunderbolt: Call tb_check_quirks() after initializing adapters
+    - thunderbolt: Disable interrupt auto clear for rings
+    - thunderbolt: Add missing UNSET_INBOUND_SBTX for retimer access
+    - thunderbolt: Use const qualifier for `ring_interrupt_index`
+    - thunderbolt: Rename shadowed variables bit to interrupt_bit and
+      auto_clear_bit
+    - ACPI: x86: utils: Add Cezanne to the list for forcing StorageD3Enable
+    - riscv: Bump COMMAND_LINE_SIZE value to 1024
+    - drm/cirrus: NULL-check pipe->plane.state->fb in cirrus_pipe_update()
+    - HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
+    - ca8210: fix mac_len negative array access
+    - HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
+    - m68k: Only force 030 bus error if PC not in exception table
+    - selftests/bpf: check that modifier resolves after pointer
+    - scsi: target: iscsi: Fix an error message in iscsi_check_key()
+    - scsi: hisi_sas: Check devm_add_action() return value
+    - scsi: ufs: core: Add soft dependency on governor_simpleondemand
+    - scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read()
+    - scsi: lpfc: Avoid usage of list iterator variable after loop
+    - scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
+    - net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
+    - net: usb: qmi_wwan: add Telit 0x1080 composition
+    - sh: sanitize the flags on sigreturn
+    - net/sched: act_mirred: better wording on protection against excessive stack
+      growth
+    - act_mirred: use the backlog for nested calls to mirred ingress
+    - cifs: empty interface list when server doesn't support query interfaces
+    - cifs: print session id while listing open files
+    - scsi: core: Add BLIST_SKIP_VPD_PAGES for SKhynix H28U74301AMR
+    - usb: dwc2: fix a devres leak in hw_enable upon suspend resume
+    - usb: gadget: u_audio: don't let userspace block driver unbind
+    - efi: sysfb_efi: Fix DMI quirks not working for simpledrm
+    - mm/slab: Fix undefined init_cache_node_node() for NUMA and !SMP
+    - fscrypt: destroy keyring after security_sb_delete()
+    - fsverity: Remove WQ_UNBOUND from fsverity read workqueue
+    - lockd: set file_lock start and end when decoding nlm4 testargs
+    - arm64: dts: imx8mm-nitrogen-r2: fix WM8960 clock name
+    - igb: revert rtnl_lock() that causes deadlock
+    - dm thin: fix deadlock when swapping to thin device
+    - usb: typec: tcpm: fix warning when handle discover_identity message
+    - usb: cdns3: Fix issue with using incorrect PCI device function
+    - usb: cdnsp: Fixes issue with redundant Status Stage
+    - usb: cdnsp: changes PCI Device ID to fix conflict with CNDS3 driver
+    - usb: chipdea: core: fix return -EINVAL if request role is the same with
+      current role
+    - usb: chipidea: core: fix possible concurrent when switch role
+    - usb: ucsi: Fix NULL pointer deref in ucsi_connector_change()
+    - kfence: avoid passing -g for test
+    - KVM: x86: hyper-v: Avoid calling kvm_make_vcpus_request_mask() with
+      vcpu_mask==NULL
+    - ksmbd: set FILE_NAMED_STREAMS attribute in FS_ATTRIBUTE_INFORMATION
+    - ksmbd: return STATUS_NOT_SUPPORTED on unsupported smb2.0 dialect
+    - ksmbd: return unsupported error on smb1 mount
+    - wifi: mac80211: fix qos on mesh interfaces
+    - nilfs2: fix kernel-infoleak in nilfs_ioctl_wrap_copy()
+    - drm/bridge: lt8912b: return EPROBE_DEFER if bridge is not found
+    - drm/meson: fix missing component unbind on bind errors
+    - drm/amdgpu/nv: Apply ASPM quirk on Intel ADL + AMD Navi
+    - drm/i915/active: Fix missing debug object activation
+    - drm/i915: Preserve crtc_state->inherited during state clearing
+    - riscv: mm: Fix incorrect ASID argument when flushing TLB
+    - riscv: Handle zicsr/zifencei issues between clang and binutils
+    - tee: amdtee: fix race condition in amdtee_open_session
+    - firmware: arm_scmi: Fix device node validation for mailbox transport
+    - i2c: xgene-slimpro: Fix out-of-bounds bug in xgene_slimpro_i2c_xfer()
+    - dm stats: check for and propagate alloc_percpu failure
+    - dm crypt: add cond_resched() to dmcrypt_write()
+    - dm crypt: avoid accessing uninitialized tasklet
+    - sched/fair: sanitize vruntime of entity being placed
+    - sched/fair: Sanitize vruntime of entity being migrated
+    - mm: kfence: fix using kfence_metadata without initialization in
+      show_object()
+    - ocfs2: fix data corruption after failed write
+    - Linux 5.15.105
+
+  * Jammy update: v5.15.104 upstream stable release (LP: #2023225)
+    - xfrm: Allow transport-mode states with AF_UNSPEC selector
+    - drm/panfrost: Don't sync rpm suspension after mmu flushing
+    - cifs: Move the in_send statistic to __smb_send_rqst()
+    - drm/meson: fix 1px pink line on GXM when scaling video overlay
+    - clk: HI655X: select REGMAP instead of depending on it
+    - docs: Correct missing "d_" prefix for dentry_operations member
+      d_weak_revalidate
+    - scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add()
+    - ALSA: hda: Match only Intel devices with CONTROLLER_IN_GPU()
+    - netfilter: nft_nat: correct length for loading protocol registers
+    - netfilter: nft_masq: correct length for loading protocol registers
+    - netfilter: nft_redir: correct length for loading protocol registers
+    - netfilter: nft_redir: correct value of inet type `.maxattrs`
+    - scsi: core: Fix a procfs host directory removal regression
+    - tcp: tcp_make_synack() can be called from process context
+    - nfc: pn533: initialize struct pn533_out_arg properly
+    - ipvlan: Make skb->skb_iif track skb->dev for l3s mode
+    - i40e: Fix kernel crash during reboot when adapter is in recovery mode
+    - vdpa_sim: not reset state in vdpasim_queue_ready
+    - vdpa_sim: set last_used_idx as last_avail_idx in vdpasim_queue_ready
+    - PCI: s390: Fix use-after-free of PCI resources with per-function hotplug
+    - drm/i915/display: Workaround cursor left overs with PSR2 selective fetch
+      enabled
+    - drm/i915/display/psr: Use drm damage helpers to calculate plane damaged area
+    - drm/i915/display: clean up comments
+    - drm/i915/psr: Use calculated io and fast wake lines
+    - net/smc: fix NULL sndbuf_desc in smc_cdc_tx_handler()
+    - qed/qed_dev: guard against a possible division by zero
+    - net: dsa: mt7530: remove now incorrect comment regarding port 5
+    - net: dsa: mt7530: set PLL frequency and trgmii only when trgmii is used
+    - loop: Fix use-after-free issues
+    - net: tunnels: annotate lockless accesses to dev->needed_headroom
+    - net: phy: smsc: bail out in lan87xx_read_status if genphy_read_status fails
+    - nfc: st-nci: Fix use after free bug in ndlc_remove due to race condition
+    - net/smc: fix deadlock triggered by cancel_delayed_work_syn()
+    - net: usb: smsc75xx: Limit packet length to skb->len
+    - drm/bridge: Fix returned array size name for atomic_get_input_bus_fmts kdoc
+    - block: null_blk: Fix handling of fake timeout request
+    - nvme: fix handling single range discard request
+    - nvmet: avoid potential UAF in nvmet_req_complete()
+    - block: sunvdc: add check for mdesc_grab() returning NULL
+    - ice: xsk: disable txq irq before flushing hw
+    - net: dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
+    - ravb: avoid PHY being resumed when interface is not up
+    - sh_eth: avoid PHY being resumed when interface is not up
+    - ipv4: Fix incorrect table ID in IOCTL path
+    - net: usb: smsc75xx: Move packet length check to prevent kernel panic in
+      skb_pull
+    - net/iucv: Fix size of interrupt data
+    - qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
+    - ethernet: sun: add check for the mdesc_grab()
+    - bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
+    - bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
+    - hwmon: (adt7475) Display smoothing attributes in correct order
+    - hwmon: (adt7475) Fix masking of hysteresis registers
+    - hwmon: (xgene) Fix use after free bug in xgene_hwmon_remove due to race
+      condition
+    - hwmon: (ina3221) return prober error code
+    - hwmon: (ucd90320) Add minimum delay between bus accesses
+    - hwmon: tmp512: drop of_match_ptr for ID table
+    - kconfig: Update config changed flag before calling callback
+    - hwmon: (adm1266) Set `can_sleep` flag for GPIO chip
+    - hwmon: (ltc2992) Set `can_sleep` flag for GPIO chip
+    - media: m5mols: fix off-by-one loop termination error
+    - mmc: atmel-mci: fix race between stop command and start of next command
+    - jffs2: correct logic when creating a hole in jffs2_write_begin
+    - ext4: fail ext4_iget if special inode unallocated
+    - ext4: update s_journal_inum if it changes after journal replay
+    - ext4: fix task hung in ext4_xattr_delete_inode
+    - drm/amdkfd: Fix an illegal memory access
+    - net/9p: fix bug in client create for .L
+    - sh: intc: Avoid spurious sizeof-pointer-div warning
+    - drm/amd/display: fix shift-out-of-bounds in CalculateVMAndRowBytes
+    - ext4: fix possible double unlock when moving a directory
+    - tty: serial: fsl_lpuart: skip waiting for transmission complete when
+      UARTCTRL_SBK is asserted
+    - serial: 8250_em: Fix UART port type
+    - serial: 8250_fsl: fix handle_irq locking
+    - firmware: xilinx: don't make a sleepable memory allocation from an atomic
+      context
+    - s390/ipl: add missing intersection check to ipl_report handling
+    - interconnect: fix mem leak when freeing nodes
+    - interconnect: exynos: fix node leak in probe PM QoS error path
+    - tracing: Make splice_read available again
+    - tracing: Check field value in hist_field_name()
+    - tracing: Make tracepoint lockdep check actually test something
+    - cifs: Fix smb2_set_path_size()
+    - ALSA: hda: intel-dsp-config: add MTL PCI id
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro
+    - Revert "riscv: mm: notify remote harts about mmu cache updates"
+    - riscv: asid: Fixup stale TLB entry cause application crash
+    - drm/shmem-helper: Remove another errant put in error path
+    - drm/sun4i: fix missing component unbind on bind errors
+    - drm/amd/pm: Fix sienna cichlid incorrect OD volage after resume
+    - mptcp: fix possible deadlock in subflow_error_report
+    - mptcp: add ro_after_init for tcp{,v6}_prot_override
+    - mptcp: avoid setting TCP_CLOSE state twice
+    - mptcp: fix lockdep false positive in mptcp_pm_nl_create_listen_socket()
+    - ftrace: Fix invalid address access in lookup_rec() when index is 0
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV3000
+    - mm/userfaultfd: propagate uffd-wp bit when PTE-mapping the huge zeropage
+    - mmc: sdhci_am654: lower power-on failed message severity
+    - fbdev: stifb: Provide valid pixelclock and add fb_check_var() checks
+    - trace/hwlat: Do not wipe the contents of per-cpu thread data
+    - net: phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit
+    - cpuidle: psci: Iterate backwards over list in psci_pd_remove()
+    - x86/mce: Make sure logged MCEs are processed after sysfs update
+    - x86/mm: Fix use of uninitialized buffer in sme_enable()
+    - x86/resctrl: Clear staged_config[] before and after it is used
+    - drm/i915: Don't use stolen memory for ring buffers with LLC
+    - drm/i915/active: Fix misuse of non-idle barriers as fence trackers
+    - io_uring: avoid null-ptr-deref in io_arm_poll_handler
+    - PCI: Unify delay handling for reset and resume
+    - PCI/DPC: Await readiness of secondary bus after reset
+    - HID: core: Provide new max_buffer_size attribute to over-ride the default
+    - HID: uhid: Over-ride the default maximum data buffer value with our own
+    - perf: Fix check before add_event_to_groups() in perf_group_detach()
+    - Linux 5.15.104
+
+  * Jammy update: v5.15.103 upstream stable release (LP: #2023224)
+    - fs: prevent out-of-bounds array speculation when closing a file descriptor
+    - btrfs: fix percent calculation for bg reclaim message
+    - perf inject: Fix --buildid-all not to eat up MMAP2
+    - fork: allow CLONE_NEWTIME in clone3 flags
+    - x86/CPU/AMD: Disable XSAVES on AMD family 0x17
+    - drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc15
+    - drm/connector: print max_requested_bpc in state debugfs
+    - staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
+    - ext4: fix cgroup writeback accounting with fs-layer encryption
+    - ext4: fix RENAME_WHITEOUT handling for inline directories
+    - ext4: fix another off-by-one fsmap error on 1k block filesystems
+    - ext4: move where set the MAY_INLINE_DATA flag is set
+    - ext4: fix WARNING in ext4_update_inline_data
+    - ext4: zero i_disksize when initializing the bootloader inode
+    - nfc: change order inside nfc_se_io error path
+    - KVM: Optimize kvm_make_vcpus_request_mask() a bit
+    - KVM: Pre-allocate cpumasks for kvm_make_all_cpus_request_except()
+    - KVM: Register /dev/kvm as the _very_ last thing during initialization
+    - KVM: SVM: Don't rewrite guest ICR on AVIC IPI virtualization failure
+    - KVM: SVM: Process ICR on AVIC IPI delivery failure due to invalid target
+    - fs: dlm: fix log of lowcomms vs midcomms
+    - fs: dlm: add midcomms init/start functions
+    - fs: dlm: start midcomms before scand
+    - udf: Fix off-by-one error when discarding preallocation
+    - f2fs: avoid down_write on nat_tree_lock during checkpoint
+    - f2fs: do not bother checkpoint by f2fs_get_node_info
+    - f2fs: retry to update the inode page given data corruption
+    - ipmi:ssif: Increase the message retry time
+    - ipmi:ssif: Add a timer between request retries
+    - irqdomain: Refactor __irq_domain_alloc_irqs()
+    - iommu/vt-d: Fix PASID directory pointer coherency
+    - block/brd: add error handling support for add_disk()
+    - brd: mark as nowait compatible
+    - arm64: efi: Make efi_rt_lock a raw_spinlock
+    - RISC-V: Avoid dereferening NULL regs in die()
+    - riscv: Avoid enabling interrupts in die()
+    - riscv: Add header include guards to insn.h
+    - scsi: core: Remove the /proc/scsi/${proc_name} directory earlier
+    - regulator: Flag uncontrollable regulators as always_on
+    - regulator: core: Fix off-on-delay-us for always-on/boot-on regulators
+    - regulator: core: Use ktime_get_boottime() to determine how long a regulator
+      was off
+    - ext4: Fix possible corruption when moving a directory
+    - drm/nouveau/kms/nv50-: remove unused functions
+    - drm/nouveau/kms/nv50: fix nv50_wndw_new_ prototype
+    - drm/msm: Fix potential invalid ptr free
+    - drm/msm/a5xx: fix setting of the CP_PREEMPT_ENABLE_LOCAL register
+    - drm/msm/a5xx: fix highest bank bit for a530
+    - drm/msm/a5xx: fix the emptyness check in the preempt code
+    - drm/msm/a5xx: fix context faults during ring switch
+    - bgmac: fix *initial* chip reset to support BCM5358
+    - nfc: fdp: add null check of devm_kmalloc_array in
+      fdp_nci_i2c_read_device_properties
+    - powerpc: dts: t1040rdb: fix compatible string for Rev A boards
+    - ila: do not generate empty messages in ila_xlat_nl_cmd_get_mapping()
+    - selftests: nft_nat: ensuring the listening side is up before starting the
+      client
+    - perf stat: Fix counting when initial delay configured
+    - net: lan78xx: fix accessing the LAN7800's internal phy specific registers
+      from the MAC driver
+    - net: caif: Fix use-after-free in cfusbl_device_notify()
+    - ice: copy last block omitted in ice_get_module_eeprom()
+    - bpf, sockmap: Fix an infinite loop error when len is 0 in
+      tcp_bpf_recvmsg_parser()
+    - drm/msm/dpu: fix len of sc7180 ctl blocks
+    - net: stmmac: add to set device wake up flag when stmmac init phy
+    - net: phylib: get rid of unnecessary locking
+    - bnxt_en: Avoid order-5 memory allocation for TPA data
+    - netfilter: tproxy: fix deadlock due to missing BH disable
+    - btf: fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
+    - net: phy: smsc: Cache interrupt mask
+    - net: phy: smsc: fix link up detection in forced irq mode
+    - net: ethernet: mtk_eth_soc: fix RX data corruption issue
+    - scsi: megaraid_sas: Update max supported LD IDs to 240
+    - platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
+    - net/smc: fix fallback failed while sendmsg with fastopen
+    - octeontx2-af: Unlock contexts in the queue context cache in case of fault
+      detection
+    - SUNRPC: Fix a server shutdown leak
+    - net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
+    - af_unix: Remove unnecessary brackets around CONFIG_AF_UNIX_OOB.
+    - af_unix: fix struct pid leaks in OOB support
+    - riscv: Use READ_ONCE_NOCHECK in imprecise unwinding stack mode
+    - s390/ftrace: remove dead code
+    - RISC-V: Don't check text_mutex during stop_machine
+    - ext4: Fix deadlock during directory rename
+    - irqdomain: Fix mapping-creation race
+    - nbd: use the correct block_device in nbd_bdev_reset
+    - iommu/amd: Add PCI segment support for ivrs_[ioapic/hpet/acpihid] commands
+    - iommu/amd: Fix ill-formed ivrs_ioapic, ivrs_hpet and ivrs_acpihid options
+    - iommu/amd: Add a length limitation for the ivrs_acpihid command-line
+      parameter
+    - staging: rtl8723bs: clean up comparsions to NULL
+    - Staging: rtl8723bs: Placing opening { braces in previous line
+    - staging: rtl8723bs: fix placement of braces
+    - staging: rtl8723bs: Fix key-store index handling
+    - watch_queue: fix IOC_WATCH_QUEUE_SET_SIZE alloc error paths
+    - tpm/eventlog: Don't abort tpm_read_log on faulty ACPI address
+    - xfs: use setattr_copy to set vfs inode attributes
+    - xfs: remove XFS_PREALLOC_SYNC
+    - xfs: fallocate() should call file_modified()
+    - xfs: set prealloc flag in xfs_alloc_file_space()
+    - fs: add mode_strip_sgid() helper
+    - fs: move S_ISGID stripping into the vfs_*() helpers
+    - attr: add in_group_or_capable()
+    - fs: move should_remove_suid()
+    - attr: add setattr_should_drop_sgid()
+    - attr: use consistent sgid stripping checks
+    - fs: use consistent setgid checks in is_sxid()
+    - MIPS: Fix a compilation issue
+    - powerpc/iommu: fix memory leak with using debugfs_lookup()
+    - powerpc/kcsan: Exclude udelay to prevent recursive instrumentation
+    - alpha: fix R_ALPHA_LITERAL reloc for large modules
+    - macintosh: windfarm: Use unsigned type for 1-bit bitfields
+    - PCI: Add SolidRun vendor ID
+    - scripts: handle BrokenPipeError for python scripts
+    - media: ov5640: Fix analogue gain control
+    - media: rc: gpio-ir-recv: add remove function
+    - filelocks: use mount idmapping for setlease permission check
+    - ext4: refactor ext4_free_blocks() to pull out ext4_mb_clear_bb()
+    - ext4: add ext4_sb_block_valid() refactored out of ext4_inode_block_valid()
+    - ext4: add strict range checks while freeing blocks
+    - ext4: block range must be validated before use in ext4_mb_clear_bb()
+    - arch: fix broken BuildID for arm64 and riscv
+    - powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT
+    - powerpc/vmlinux.lds: Don't discard .rela* for relocatable builds
+    - s390: define RUNTIME_DISCARD_EXIT to fix link error with GNU ld < 2.36
+    - sh: define RUNTIME_DISCARD_EXIT
+    - tools build: Add feature test for init_disassemble_info API changes
+    - tools include: add dis-asm-compat.h to handle version differences
+    - tools perf: Fix compilation error with new binutils
+    - tools bpf_jit_disasm: Fix compilation error with new binutils
+    - tools bpftool: Fix compilation error with new binutils
+    - KVM: fix memoryleak in kvm_init()
+    - xfs: remove xfs_setattr_time() declaration
+    - UML: define RUNTIME_DISCARD_EXIT
+    - fs: hold writers when changing mount's idmapping
+    - KVM: nVMX: Don't use Enlightened MSR Bitmap for L3
+    - KVM: VMX: Introduce vmx_msr_bitmap_l01_changed() helper
+    - KVM: VMX: Fix crash due to uninitialized current_vmcs
+    - Makefile: use -gdwarf-{4|5} for assembler for DEBUG_INFO_DWARF{4|5}
+    - Linux 5.15.103
+
+  * Jammy update: v5.15.102 upstream stable release (LP: #2020393)
+    - staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
+    - staging: rtl8192e: Remove call_usermodehelper starting RadioPower.sh
+    - Linux 5.15.102
+
+  * Jammy update: v5.15.101 upstream stable release (LP: #2020391)
+    - Linux 5.15.101
+
+  * Jammy update: v5.15.100 upstream stable release (LP: #2020387)
+    - auxdisplay: hd44780: Fix potential memory leak in hd44780_remove()
+    - fs/jfs: fix shift exponent db_agl2size negative
+    - objtool: Fix memory leak in create_static_call_sections()
+    - pwm: sifive: Reduce time the controller lock is held
+    - pwm: sifive: Always let the first pwm_apply_state succeed
+    - pwm: stm32-lp: fix the check on arr and cmp registers update
+    - f2fs: use memcpy_{to,from}_page() where possible
+    - fs: f2fs: initialize fsdata in pagecache_write()
+    - f2fs: allow set compression option of files without blocks
+    - um: vector: Fix memory leak in vector_config
+    - ubi: ensure that VID header offset + VID header size <= alloc, size
+    - ubifs: Fix build errors as symbol undefined
+    - ubifs: Rectify space budget for ubifs_symlink() if symlink is encrypted
+    - ubifs: Rectify space budget for ubifs_xrename()
+    - ubifs: Fix wrong dirty space budget for dirty inode
+    - ubifs: do_rename: Fix wrong space budget when target inode's nlink > 1
+    - ubifs: Reserve one leb for each journal head while doing budget
+    - ubi: Fix use-after-free when volume resizing failed
+    - ubi: Fix unreferenced object reported by kmemleak in ubi_resize_volume()
+    - ubifs: Fix memory leak in alloc_wbufs()
+    - ubi: Fix possible null-ptr-deref in ubi_free_volume()
+    - ubifs: Re-statistic cleaned znode count if commit failed
+    - ubifs: ubifs_writepage: Mark page dirty after writing inode failed
+    - ubi: fastmap: Fix missed fm_anchor PEB in wear-leveling after disabling
+      fastmap
+    - ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
+    - ubi: ubi_wl_put_peb: Fix infinite loop when wear-leveling work failed
+    - f2fs: fix to avoid potential memory corruption in __update_iostat_latency()
+    - ext4: use ext4_fc_tl_mem in fast-commit replay path
+    - netfilter: nf_tables: allow to fetch set elements when table has an owner
+    - x86: um: vdso: Add '%rcx' and '%r11' to the syscall clobber list
+    - um: virtio_uml: free command if adding to virtqueue failed
+    - um: virtio_uml: mark device as unregistered when breaking it
+    - um: virtio_uml: move device breaking into workqueue
+    - um: virt-pci: properly remove PCI device from bus
+    - watchdog: at91sam9_wdt: use devm_request_irq to avoid missing free_irq() in
+      error path
+    - watchdog: Fix kmemleak in watchdog_cdev_register
+    - watchdog: pcwd_usb: Fix attempting to access uninitialized memory
+    - watchdog: sbsa_wdog: Make sure the timeout programming is within the limits
+    - netfilter: ctnetlink: fix possible refcount leak in
+      ctnetlink_create_conntrack()
+    - netfilter: ebtables: fix table blob use-after-free
+    - netfilter: x_tables: fix percpu counter block leak on error path when
+      creating new netns
+    - ipv6: Add lwtunnel encap size of all siblings in nexthop calculation
+    - sctp: add a refcnt in sctp_stream_priorities to avoid a nested loop
+    - octeontx2-pf: Use correct struct reference in test condition
+    - net: fix __dev_kfree_skb_any() vs drop monitor
+    - 9p/xen: fix version parsing
+    - 9p/xen: fix connection sequence
+    - 9p/rdma: unmap receive dma buffer in rdma_request()/post_recv()
+    - net/mlx5e: Verify flow_source cap before using it
+    - net/mlx5: Geneve, Fix handling of Geneve object id as error code
+    - nfc: fix memory leak of se_io context in nfc_genl_se_io
+    - net/sched: transition act_pedit to rcu and percpu stats
+    - net/sched: act_pedit: fix action bind logic
+    - net/sched: act_mpls: fix action bind logic
+    - net/sched: act_sample: fix action bind logic
+    - ARM: dts: spear320-hmi: correct STMPE GPIO compatible
+    - tcp: tcp_check_req() can be called from process context
+    - vc_screen: modify vcs_size() handling in vcs_read()
+    - rtc: sun6i: Always export the internal oscillator
+    - genirq: Refactor accessors to use irq_data_get_affinity_mask
+    - genirq: Add and use an irq_data_update_affinity helper
+    - scsi: ipr: Work around fortify-string warning
+    - rtc: allow rtc_read_alarm without read_alarm callback
+    - loop: loop_set_status_from_info() check before assignment
+    - ASoC: adau7118: don't disable regulators on device unbind
+    - ASoC: zl38060: Remove spurious gpiolib select
+    - ASoC: zl38060 add gpiolib dependency
+    - ASoC: mediatek: mt8195: add missing initialization
+    - thermal: intel: quark_dts: fix error pointer dereference
+    - thermal: intel: BXT_PMIC: select REGMAP instead of depending on it
+    - tracing: Add NULL checks for buffer in ring_buffer_free_read_page()
+    - kernel/printk/index.c: fix memory leak with using debugfs_lookup()
+    - firmware/efi sysfb_efi: Add quirk for Lenovo IdeaPad Duet 3
+    - bootconfig: Increase max nodes of bootconfig from 1024 to 8192 for DCC
+      support
+    - mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
+    - IB/hfi1: Update RMT size calculation
+    - iommu/amd: Fix error handling for pdev_pri_ats_enable()
+    - media: uvcvideo: Remove format descriptions
+    - media: uvcvideo: Handle cameras with invalid descriptors
+    - media: uvcvideo: Handle errors from calls to usb_string
+    - media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910
+    - media: uvcvideo: Silence memcpy() run-time false positive warnings
+    - USB: fix memory leak with using debugfs_lookup()
+    - staging: emxx_udc: Add checks for dma_alloc_coherent()
+    - tty: fix out-of-bounds access in tty_driver_lookup_tty()
+    - tty: serial: fsl_lpuart: disable the CTS when send break signal
+    - serial: sc16is7xx: setup GPIO controller later in probe
+    - mei: bus-fixup:upon error print return values of send and receive
+    - tools/iio/iio_utils:fix memory leak
+    - iio: accel: mma9551_core: Prevent uninitialized variable in
+      mma9551_read_status_word()
+    - iio: accel: mma9551_core: Prevent uninitialized variable in
+      mma9551_read_config_word()
+    - soundwire: bus_type: Avoid lockdep assert in sdw_drv_probe()
+    - PCI: loongson: Prevent LS7A MRRS increases
+    - USB: dwc3: fix memory leak with using debugfs_lookup()
+    - USB: chipidea: fix memory leak with using debugfs_lookup()
+    - USB: uhci: fix memory leak with using debugfs_lookup()
+    - USB: sl811: fix memory leak with using debugfs_lookup()
+    - USB: fotg210: fix memory leak with using debugfs_lookup()
+    - USB: isp116x: fix memory leak with using debugfs_lookup()
+    - USB: isp1362: fix memory leak with using debugfs_lookup()
+    - USB: gadget: gr_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: bcm63xx_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: lpc32xx_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: pxa25x_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: pxa27x_udc: fix memory leak with using debugfs_lookup()
+    - usb: host: xhci: mvebu: Iterate over array indexes instead of using pointer
+      math
+    - USB: ene_usb6250: Allocate enough memory for full object
+    - usb: uvc: Enumerate valid values for color matching
+    - usb: gadget: uvc: Make bSourceID read/write
+    - PCI: Align extra resources for hotplug bridges properly
+    - PCI: Take other bus devices into account when distributing resources
+    - tty: pcn_uart: fix memory leak with using debugfs_lookup()
+    - misc: vmw_balloon: fix memory leak with using debugfs_lookup()
+    - drivers: base: component: fix memory leak with using debugfs_lookup()
+    - drivers: base: dd: fix memory leak with using debugfs_lookup()
+    - kernel/fail_function: fix memory leak with using debugfs_lookup()
+    - PCI: loongson: Add more devices that need MRRS quirk
+    - PCI: Add ACS quirk for Wangxun NICs
+    - phy: rockchip-typec: Fix unsigned comparison with less than zero
+    - soundwire: cadence: Remove wasted space in response_buf
+    - soundwire: cadence: Drain the RX FIFO after an IO timeout
+    - net: tls: avoid hanging tasks on the tx_lock
+    - x86/resctl: fix scheduler confusion with 'current'
+    - drm/display/dp_mst: Fix down/up message handling after sink disconnect
+    - drm/display/dp_mst: Fix down message handling after a packet reception error
+    - Bluetooth: hci_sock: purge socket queues in the destruct() callback
+    - media: uvcvideo: Fix race condition with usb_kill_urb
+    - drm/virtio: Fix error code in virtio_gpu_object_shmem_init()
+    - Revert "scsi: mpt3sas: Fix return value check of dma_get_required_mask()"
+    - scsi: mpt3sas: Don't change DMA mask while reallocating pools
+    - scsi: mpt3sas: re-do lost mpt3sas DMA mask fix
+    - scsi: mpt3sas: Remove usage of dma_get_required_mask() API
+    - malidp: Fix NULL vs IS_ERR() checking
+    - usb: gadget: uvc: fix missing mutex_unlock() if kstrtou8() fails
+    - Linux 5.15.100
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] update annotations scripts
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Mon, 10 Jul 2023 15:33:56 +0200
+
+linux (5.15.0-76.83) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-76.83 -proposed tracker (LP: #2023905)
+
+  * cls_flower: off-by-one in fl_set_geneve_opt (LP: #2023577)
+    - net/sched: flower: fix possible OOB write in fl_set_geneve_opt()
+
+  * Some INVLPG implementations can leave Global translations unflushed when
+    PCIDs are enabled (LP: #2023220)
+    - x86/mm: Avoid incomplete Global INVLPG flushes
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Thu, 15 Jun 2023 14:47:18 -0300
+
+linux (5.15.0-75.82) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-75.82 -proposed tracker (LP: #2023065)
+
+  * Jammy update: v5.15.102 upstream stable release (LP: #2020393)
+    - wifi: cfg80211: Partial revert "wifi: cfg80211: Fix use after free for wext"
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] resync getabis
+
+  * fix typo in config-checks invocation (LP: #2020413)
+    - [Packaging] fix typo when calling the old config-check
+    - [Packaging] fix typo in 4-checks.mk
+
+  * support python < 3.9 with annotations (LP: #2020531)
+    - [Packaging] kconfig/annotations.py: support older way of merging dicts
+
+ -- Luke Nowakowski-Krijger <luke.nowakowskikrijger@canonical.com>  Tue, 06 Jun 2023 15:50:32 -0700
+
+linux (5.15.0-74.81) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-74.81 -proposed tracker (LP: #2019420)
+
+  * smartpqi: Update 22.04 driver to include recent bug fixes and support
+    current generation devices (LP: #1998643)
+    - scsi: smartpqi: Switch to attribute groups
+    - scsi: smartpqi: Fix rmmod stack trace
+    - scsi: smartpqi: Add PCI IDs
+    - scsi: smartpqi: Enable SATA NCQ priority in sysfs
+    - scsi: smartpqi: Eliminate drive spin down on warm boot
+    - scsi: smartpqi: Quickly propagate path failures to SCSI midlayer
+    - scsi: smartpqi: Fix a name typo and cleanup code
+    - scsi: smartpqi: Fix a typo in func pqi_aio_submit_io()
+    - scsi: smartpqi: Resolve delay issue with PQI_HZ value
+    - scsi: smartpqi: Avoid drive spin-down during suspend
+    - scsi: smartpqi: Update volume size after expansion
+    - scsi: smartpqi: Speed up RAID 10 sequential reads
+    - scsi: smartpqi: Expose SAS address for SATA drives
+    - scsi: smartpqi: Fix NUMA node not updated during init
+    - scsi: smartpqi: Fix BUILD_BUG_ON() statements
+    - scsi: smartpqi: Fix hibernate and suspend
+    - scsi: smartpqi: Fix lsscsi -t SAS addresses
+    - scsi: smartpqi: Update version to 2.1.14-035
+    - scsi: smartpqi: Fix unused variable pqi_pm_ops for clang
+    - scsi: smartpqi: Stop using the SCSI pointer
+    - scsi: smartpqi: Fix typo in comment
+    - scsi: smartpqi: Shorten drive visibility after removal
+    - scsi: smartpqi: Add controller fw version to console log
+    - scsi: smartpqi: Add PCI IDs for ramaxel controllers
+    - scsi: smartpqi: Close write read holes
+    - scsi: smartpqi: Add driver support for multi-LUN devices
+    - scsi: smartpqi: Fix PCI control linkdown system hang
+    - scsi: smartpqi: Add PCI ID for Adaptec SmartHBA 2100-8i
+    - scsi: smartpqi: Add PCI IDs for Lenovo controllers
+    - scsi: smartpqi: Stop logging spurious PQI reset failures
+    - scsi: smartpqi: Fix RAID map race condition
+    - scsi: smartpqi: Add module param to disable managed ints
+    - scsi: smartpqi: Update deleting a LUN via sysfs
+    - scsi: smartpqi: Add ctrl ready timeout module parameter
+    - scsi: smartpqi: Update copyright to current year
+    - scsi: smartpqi: Update version to 2.1.18-045
+    - scsi: smartpqi: Convert to host_tagset
+    - scsi: smartpqi: Add new controller PCI IDs
+    - scsi: smartpqi: Correct max LUN number
+    - scsi: smartpqi: Change sysfs raid_level attribute to N/A for controllers
+    - scsi: smartpqi: Correct device removal for multi-actuator devices
+    - scsi: smartpqi: Add controller cache flush during rmmod
+    - scsi: smartpqi: Initialize feature section info
+    - scsi: smartpqi: Change version to 2.1.20-035
+
+  * CVE-2023-32233
+    - netfilter: nf_tables: deactivate anonymous set from preparation phase
+
+  * CVE-2023-2612
+    - SAUCE: shiftfs: prevent lock unbalance in shiftfs_create_object()
+
+  * CVE-2023-31436
+    - net: sched: sch_qfq: prevent slab-out-of-bounds in qfq_activate_agg
+
+  * CVE-2023-1380
+    - wifi: brcmfmac: slab-out-of-bounds read in brcmf_get_assoc_ies()
+
+  * Add  PPIN support for Intel EMR cpu (LP: #2019131)
+    - x86/cpu: Merge Intel and AMD ppin_init() functions
+    - x86/cpu: Add Xeon Emerald Rapids to list of CPUs that support PPIN
+
+  * conntrack mark is not advertised via netlink (LP: #2016269)
+    - netfilter: ctnetlink: revert to dumping mark regardless of event type
+
+  * [SRU] Backport request for hpwdt from upstream 6.1 to Jammy (LP: #2008751)
+    - watchdog/hpwdt: Enable HP_WATCHDOG for ARM64 systems.
+    - watchdog/hpwdt: Include nmi.h only if CONFIG_HPWDT_NMI_DECODING
+    - [Config] Add arm64 option to CONFIG_HP_WATCHDOG
+
+  * Ubuntu 22.04 raise abnormal NIC MSI-X requests with larger CPU cores (256)
+    (LP: #2012335)
+    - ice: Allow operation with reduced device MSI-X
+
+  * Dell: Enable speaker mute hotkey LED indicator (LP: #2015972)
+    - platform/x86: dell-laptop: Register ctl-led for speaker-mute
+
+  * [SRU]With "Performance per Watt (DAPC)" enabled in the BIOS, Bootup time is
+    taking longer than expected (LP: #2008527)
+    - cpufreq: ACPI: Defer setting boost MSRs
+
+  * [SRU][Jammy] CONFIG_PCI_MESON is not enabled (LP: #2007745)
+    - [Config] arm64: Enable PCI_MESON module
+
+  * Jammy update: v5.15.99 upstream stable release (LP: #2018438)
+    - HID: asus: use spinlock to protect concurrent accesses
+    - HID: asus: use spinlock to safely schedule workers
+    - powerpc/mm: Rearrange if-else block to avoid clang warning
+    - ARM: OMAP2+: Fix memory leak in realtime_counter_init()
+    - arm64: dts: qcom: qcs404: use symbol names for PCIe resets
+    - arm64: dts: qcom: msm8996-tone: Fix USB taking 6 minutes to wake up
+    - arm64: dts: qcom: sm8150-kumano: Panel framebuffer is 2.5k instead of 4k
+    - arm64: dts: qcom: sm6125: Reorder HSUSB PHY clocks to match bindings
+    - arm64: dts: imx8m: Align SoC unique ID node unit address
+    - ARM: zynq: Fix refcount leak in zynq_early_slcr_init
+    - arm64: dts: mediatek: mt8183: Fix systimer 13 MHz clock description
+    - arm64: dts: qcom: sdm845-db845c: fix audio codec interrupt pin name
+    - arm64: dts: qcom: sc7180: correct SPMI bus address cells
+    - arm64: dts: qcom: sc7280: correct SPMI bus address cells
+    - arm64: dts: meson-gx: Fix Ethernet MAC address unit name
+    - arm64: dts: meson-g12a: Fix internal Ethernet PHY unit name
+    - arm64: dts: meson-gx: Fix the SCPI DVFS node name and unit address
+    - arm64: dts: msm8992-bullhead: add memory hole region
+    - arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem size
+    - arm64: dts: qcom: msm8992-bullhead: Disable dfps_data_mem
+    - arm64: dts: qcom: ipq8074: correct USB3 QMP PHY-s clock output names
+    - arm64: dts: qcom: Fix IPQ8074 PCIe PHY nodes
+    - arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
+    - arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY
+    - arm64: dts: qcom: ipq8074: correct Gen2 PCIe ranges
+    - arm64: dts: qcom: ipq8074: fix Gen3 PCIe node
+    - arm64: dts: qcom: ipq8074: correct PCIe QMP PHY output clock names
+    - arm64: dts: meson: remove CPU opps below 1GHz for G12A boards
+    - ARM: OMAP1: call platform_device_put() in error case in
+      omap1_dm_timer_init()
+    - ARM: bcm2835_defconfig: Enable the framebuffer
+    - ARM: s3c: fix s3c64xx_set_timer_source prototype
+    - arm64: dts: ti: k3-j7200: Fix wakeup pinmux range
+    - ARM: dts: exynos: correct wr-active property in Exynos3250 Rinato
+    - ARM: imx: Call ida_simple_remove() for ida_simple_get
+    - arm64: dts: amlogic: meson-gx: fix SCPI clock dvfs node name
+    - arm64: dts: amlogic: meson-axg: fix SCPI clock dvfs node name
+    - arm64: dts: amlogic: meson-gx: add missing SCPI sensors compatible
+    - arm64: dts: amlogic: meson-gxl-s905d-sml5442tw: drop invalid clock-names
+      property
+    - arm64: dts: amlogic: meson-gx: add missing unit address to rng node name
+    - arm64: dts: amlogic: meson-gxl: add missing unit address to eth-phy-mux node
+      name
+    - arm64: dts: amlogic: meson-gx-libretech-pc: fix update button name
+    - arm64: dts: amlogic: meson-sm1-bananapi-m5: fix adc keys node names
+    - arm64: dts: amlogic: meson-gxl-s905d-phicomm-n1: fix led node name
+    - arm64: dts: amlogic: meson-gxbb-kii-pro: fix led node name
+    - arm64: dts: amlogic: meson-sm1-odroid-hc4: fix active fan thermal trip
+    - locking/rwsem: Optimize down_read_trylock() under highly contended case
+    - locking/rwsem: Disable preemption in all down_read*() and up_read() code
+      paths
+    - arm64: dts: renesas: beacon-renesom: Fix gpio expander reference
+    - arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
+    - ARM: dts: sun8i: nanopi-duo2: Fix regulator GPIO reference
+    - ARM: dts: imx7s: correct iomuxc gpr mux controller cells
+    - arm64: dts: mt8192: Fix CPU map for single-cluster SoC
+    - arm64: dts: mediatek: mt7622: Add missing pwm-cells to pwm node
+    - blk-mq: avoid sleep in blk_mq_alloc_request_hctx
+    - blk-mq: remove stale comment for blk_mq_sched_mark_restart_hctx
+    - blk-mq: correct stale comment of .get_budget
+    - arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM
+      and MPSS memory regions
+    - s390/dasd: Fix potential memleak in dasd_eckd_init()
+    - sched/deadline,rt: Remove unused parameter from pick_next_[rt|dl]_entity()
+    - sched/rt: pick_next_rt_entity(): check list_entry
+    - x86/perf/zhaoxin: Add stepping check for ZXC
+    - KEYS: asymmetric: Fix ECDSA use via keyctl uapi
+    - arm64: dts: qcom: pmk8350: Specify PBS register for PON
+    - arm64: dts: qcom: pmk8350: Use the correct PON compatible
+    - block: bio-integrity: Copy flags when bio_integrity_payload is cloned
+    - wifi: rsi: Fix memory leak in rsi_coex_attach()
+    - wifi: rtlwifi: rtl8821ae: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: rtl8188ee: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: rtl8723be: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: iwlegacy: common: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: fix memory leak in lbs_init_adapter()
+    - wifi: rtl8xxxu: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: Fix global-out-of-bounds bug in
+      _rtl8812ae_phy_set_txpower_limit()
+    - libbpf: Fix btf__align_of() by taking into account field offsets
+    - wifi: ipw2x00: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: ipw2200: fix memory leak in ipw_wdev_init()
+    - wifi: wilc1000: fix potential memory leak in wilc_mac_xmit()
+    - wifi: brcmfmac: fix potential memory leak in brcmf_netdev_start_xmit()
+    - wifi: brcmfmac: unmap dma buffer in brcmf_msgbuf_alloc_pktid()
+    - wifi: libertas_tf: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: if_usb: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: main: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: cmdresp: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: wl3501_cs: don't call kfree_skb() under spin_lock_irqsave()
+    - crypto: x86/ghash - fix unaligned access in ghash_setkey()
+    - ACPICA: Drop port I/O validation for some regions
+    - genirq: Fix the return type of kstat_cpu_irqs_sum()
+    - rcu-tasks: Improve comments explaining tasks_rcu_exit_srcu purpose
+    - rcu-tasks: Remove preemption disablement around srcu_read_[un]lock() calls
+    - rcu-tasks: Fix synchronize_rcu_tasks() VS zap_pid_ns_processes()
+    - lib/mpi: Fix buffer overrun when SG is too long
+    - crypto: ccp - Avoid page allocation failure warning for SEV_GET_ID2
+    - ACPICA: nsrepair: handle cases without a return value correctly
+    - thermal/drivers/tsens: Drop msm8976-specific defines
+    - thermal/drivers/tsens: Add compat string for the qcom,msm8960
+    - thermal/drivers/tsens: Sort out msm8976 vs msm8956 data
+    - thermal/drivers/tsens: fix slope values for msm8939
+    - thermal/drivers/tsens: limit num_sensors to 9 for msm8939
+    - wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
+    - wifi: orinoco: check return value of hermes_write_wordrec()
+    - wifi: ath9k: htc_hst: free skb in ath9k_htc_rx_msg() if there is no callback
+      function
+    - ath9k: hif_usb: simplify if-if to if-else
+    - ath9k: htc: clean up statistics macros
+    - wifi: ath9k: hif_usb: clean up skbs if ath9k_hif_usb_rx_stream() fails
+    - wifi: ath9k: Fix potential stack-out-of-bounds write in
+      ath9k_wmi_rsp_callback()
+    - wifi: ath11k: Fix memory leak in ath11k_peer_rx_frag_setup
+    - wifi: cfg80211: Fix extended KCK key length check in
+      nl80211_set_rekey_data()
+    - ACPI: battery: Fix missing NUL-termination with large strings
+    - crypto: ccp - Failure on re-initialization due to duplicate sysfs filename
+    - crypto: essiv - Handle EBUSY correctly
+    - crypto: seqiv - Handle EBUSY correctly
+    - powercap: fix possible name leak in powercap_register_zone()
+    - x86: Mark stop_this_cpu() __noreturn
+    - x86/microcode: Rip out the OLD_INTERFACE
+    - [Config] Drop MICROCODE_OLD_INTERFACE
+    - x86/microcode: Default-disable late loading
+    - x86/microcode: Print previous version of microcode after reload
+    - x86/microcode: Add a parameter to microcode_check() to store CPU
+      capabilities
+    - x86/microcode: Check CPU capabilities after late microcode update correctly
+    - x86/microcode: Adjust late loading result reporting message
+    - crypto: xts - Handle EBUSY correctly
+    - leds: led-class: Add missing put_device() to led_put()
+    - crypto: ccp - Refactor out sev_fw_alloc()
+    - crypto: ccp - Flush the SEV-ES TMR memory before giving it to firmware
+    - bpftool: profile online CPUs instead of possible
+    - mt76: mt7915: fix polling firmware-own status
+    - net/mlx5: Enhance debug print in page allocation failure
+    - irqchip: Fix refcount leak in platform_irqchip_probe
+    - irqchip/alpine-msi: Fix refcount leak in alpine_msix_init_domains
+    - irqchip/irq-mvebu-gicp: Fix refcount leak in mvebu_gicp_probe
+    - irqchip/ti-sci: Fix refcount leak in ti_sci_intr_irq_domain_probe
+    - s390/mem_detect: fix detect_memory() error handling
+    - s390/vmem: fix empty page tables cleanup under KASAN
+    - net: add sock_init_data_uid()
+    - tun: tun_chr_open(): correctly initialize socket uid
+    - tap: tap_open(): correctly initialize socket uid
+    - OPP: fix error checking in opp_migrate_dentry()
+    - Bluetooth: L2CAP: Fix potential user-after-free
+    - Bluetooth: hci_qca: get wakeup status from serdev device handle
+    - s390/ap: fix status returned by ap_aqic()
+    - s390/ap: fix status returned by ap_qact()
+    - libbpf: Fix alen calculation in libbpf_nla_dump_errormsg()
+    - rds: rds_rm_zerocopy_callback() correct order for list_add_tail()
+    - crypto: rsa-pkcs1pad - Use akcipher_request_complete
+    - m68k: /proc/hardware should depend on PROC_FS
+    - RISC-V: time: initialize hrtimer based broadcast clock event device
+    - wifi: iwl3945: Add missing check for create_singlethread_workqueue
+    - wifi: iwl4965: Add missing check for create_singlethread_workqueue()
+    - wifi: mwifiex: fix loop iterator in mwifiex_update_ampdu_txwinsize()
+    - selftests/bpf: Fix out-of-srctree build
+    - ACPI: resource: Add IRQ overrides for MAINGEAR Vector Pro 2 models
+    - ACPI: resource: Do IRQ override on all TongFang GMxRGxx
+    - crypto: crypto4xx - Call dma_unmap_page when done
+    - wifi: mac80211: make rate u32 in sta_set_rate_info_rx()
+    - thermal/drivers/hisi: Drop second sensor hi3660
+    - can: esd_usb: Move mislocated storage of SJA1000_ECC_SEG bits in case of a
+      bus error
+    - bpf: Fix global subprog context argument resolution logic
+    - irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts
+    - irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts
+    - selftests/net: Interpret UDP_GRO cmsg data as an int value
+    - l2tp: Avoid possible recursive deadlock in l2tp_tunnel_register()
+    - net: bcmgenet: fix MoCA LED control
+    - sefltests: netdevsim: wait for devlink instance after netns removal
+    - drm: Fix potential null-ptr-deref due to drmm_mode_config_init()
+    - drm/fourcc: Add missing big-endian XRGB1555 and RGB565 formats
+    - drm/bridge: ti-sn65dsi83: Fix delay after reset deassert to match spec
+    - drm: mxsfb: DRM_MXSFB should depend on ARCH_MXS || ARCH_MXC
+    - [Config] Drop DRM_MXSFB for armhf-generic-lpae
+    - drm/bridge: megachips: Fix error handling in i2c_register_driver()
+    - drm/vkms: Fix memory leak in vkms_init()
+    - drm/vkms: Fix null-ptr-deref in vkms_release()
+    - drm/vc4: dpi: Add option for inverting pixel clock and output enable
+    - drm/vc4: dpi: Fix format mapping for RGB565
+    - drm: tidss: Fix pixel format definition
+    - gpu: ipu-v3: common: Add of_node_put() for reference returned by
+      of_graph_get_port_by_id()
+    - hwmon: (ftsteutates) Fix scaling of measurements
+    - drm/msm/hdmi: Add missing check for alloc_ordered_workqueue
+    - pinctrl: qcom: pinctrl-msm8976: Correct function names for wcss pins
+    - pinctrl: stm32: Fix refcount leak in stm32_pctrl_get_irq_domain
+    - pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
+    - drm/vc4: hvs: Set AXI panic modes
+    - drm/vc4: hvs: Fix colour order for xRGB1555 on HVS5
+    - drm/vc4: hdmi: Correct interlaced timings again
+    - drm/msm: clean event_thread->worker in case of an error
+    - scsi: qla2xxx: edif: Fix I/O timeout due to over-subscription
+    - scsi: qla2xxx: Fix exchange oversubscription
+    - scsi: qla2xxx: Fix exchange oversubscription for management commands
+    - ASoC: fsl_sai: Update to modern clocking terminology
+    - ASoC: fsl_sai: initialize is_dsp_mode flag
+    - drm/msm/adreno: Fix null ptr access in adreno_gpu_cleanup()
+    - ALSA: hda/ca0132: minor fix for allocation size
+    - drm/msm/gem: Add check for kmalloc
+    - drm/msm/dpu: Disallow unallocated resources to be returned
+    - drm/bridge: lt9611: fix sleep mode setup
+    - drm/bridge: lt9611: fix HPD reenablement
+    - drm/bridge: lt9611: fix polarity programming
+    - drm/bridge: lt9611: fix programming of video modes
+    - drm/bridge: lt9611: fix clock calculation
+    - drm/bridge: lt9611: pass a pointer to the of node
+    - drm/mipi-dsi: Fix byte order of 16-bit DCS set/get brightness
+    - drm: exynos: dsi: Fix MIPI_DSI*_NO_* mode flags
+    - drm/msm/dsi: Allow 2 CTRLs on v2.5.0
+    - drm/msm: use strscpy instead of strncpy
+    - drm/msm/dpu: Add check for cstate
+    - drm/msm/dpu: Add check for pstates
+    - drm/msm/mdp5: Add check for kzalloc
+    - pinctrl: bcm2835: Remove of_node_put() in bcm2835_of_gpio_ranges_fallback()
+    - pinctrl: mediatek: fix coding style
+    - pinctrl: mediatek: Initialize variable pullen and pullup to zero
+    - pinctrl: mediatek: Initialize variable *buf to zero
+    - gpu: host1x: Don't skip assigning syncpoints to channels
+    - drm/tegra: firewall: Check for is_addr_reg existence in IMM check
+    - drm/msm/dpu: set pdpu->is_rt_pipe early in dpu_plane_sspp_atomic_update()
+    - drm/mediatek: dsi: Reduce the time of dsi from LP11 to sending cmd
+    - drm/mediatek: Use NULL instead of 0 for NULL pointer
+    - drm/mediatek: Drop unbalanced obj unref
+    - drm/mediatek: mtk_drm_crtc: Add checks for devm_kcalloc
+    - drm/mediatek: Clean dangling pointer on bind error path
+    - ASoC: soc-compress.c: fixup private_data on snd_soc_new_compress()
+    - gpio: vf610: connect GPIO label to dev name
+    - spi: dw_bt1: fix MUX_MMIO dependencies
+    - ASoC: mchp-spdifrx: fix controls which rely on rsr register
+    - ASoC: mchp-spdifrx: fix return value in case completion times out
+    - ASoC: mchp-spdifrx: fix controls that works with completion mechanism
+    - ASoC: mchp-spdifrx: disable all interrupts in mchp_spdifrx_dai_remove()
+    - ASoC: rsnd: fixup #endif position
+    - ASoC: mchp-spdifrx: Fix uninitialized use of mr in mchp_spdifrx_hw_params()
+    - ASoC: dt-bindings: meson: fix gx-card codec node regex
+    - hwmon: (ltc2945) Handle error case in ltc2945_value_store
+    - drm/amdgpu: fix enum odm_combine_mode mismatch
+    - scsi: mpt3sas: Fix a memory leak
+    - scsi: aic94xx: Add missing check for dma_map_single()
+    - HID: multitouch: Add quirks for flipped axes
+    - HID: retain initial quirks set up when creating HID devices
+    - ASoC: codecs: Change bulk clock voting to optional voting in digital codecs
+    - ASoC: codecs: rx-macro: move clk provider to managed variants
+    - ASoC: codecs: tx-macro: move clk provider to managed variants
+    - ASoC: codecs: rx-macro: move to individual clks from bulk
+    - ASoC: codecs: tx-macro: move to individual clks from bulk
+    - ASoC: codecs: lpass: fix incorrect mclk rate
+    - spi: bcm63xx-hsspi: Fix multi-bit mode setting
+    - hwmon: (mlxreg-fan) Return zero speed for broken fan
+    - ASoC: tlv320adcx140: fix 'ti,gpio-config' DT property init
+    - dm: remove flush_scheduled_work() during local_exit()
+    - NFSv4: keep state manager thread active if swap is enabled
+    - nfs4trace: fix state manager flag printing
+    - NFS: fix disabling of swap
+    - spi: synquacer: Fix timeout handling in synquacer_spi_transfer_one()
+    - ASoC: soc-dapm.h: fixup warning struct snd_pcm_substream not declared
+    - HID: bigben: use spinlock to protect concurrent accesses
+    - HID: bigben_worker() remove unneeded check on report_field
+    - HID: bigben: use spinlock to safely schedule workers
+    - hid: bigben_probe(): validate report count
+    - drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
+    - nfsd: fix race to check ls_layouts
+    - cifs: Fix lost destroy smbd connection when MR allocate failed
+    - cifs: Fix warning and UAF when destroy the MR list
+    - gfs2: jdata writepage fix
+    - perf llvm: Fix inadvertent file creation
+    - leds: led-core: Fix refcount leak in of_led_get()
+    - perf inject: Use perf_data__read() for auxtrace
+    - perf intel-pt: Add documentation for Event Trace and TNT disable
+    - perf intel-pt: Add link to the perf wiki's Intel PT page
+    - perf intel-pt: Add support for emulated ptwrite
+    - perf intel-pt: Do not try to queue auxtrace data on pipe
+    - perf tools: Fix auto-complete on aarch64
+    - sparc: allow PM configs for sparc32 COMPILE_TEST
+    - printf: fix errname.c list
+    - objtool: add UACCESS exceptions for __tsan_volatile_read/write
+    - mfd: cs5535: Don't build on UML
+    - mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
+    - dmaengine: idxd: Set traffic class values in GRPCFG on DSA 2.0
+    - dmaengine: HISI_DMA should depend on ARCH_HISI
+    - [Config] Add HISI_DMA=n for armhf
+    - iio: light: tsl2563: Do not hardcode interrupt trigger type
+    - usb: gadget: fusb300_udc: free irq on the error path in fusb300_probe()
+    - i2c: designware: fix i2c_dw_clk_rate() return size to be u32
+    - soundwire: cadence: Don't overflow the command FIFOs
+    - driver core: fix potential null-ptr-deref in device_add()
+    - kobject: modify kobject_get_path() to take a const *
+    - kobject: Fix slab-out-of-bounds in fill_kobj_path()
+    - alpha/boot/tools/objstrip: fix the check for ELF header
+    - media: uvcvideo: Do not check for V4L2_CTRL_WHICH_DEF_VAL
+    - media: uvcvideo: Remove s_ctrl and g_ctrl
+    - media: uvcvideo: refactor __uvc_ctrl_add_mapping
+    - media: uvcvideo: Add support for V4L2_CTRL_TYPE_CTRL_CLASS
+    - media: uvcvideo: Use control names from framework
+    - media: uvcvideo: Check controls flags before accessing them
+    - media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()
+    - coresight: etm4x: Fix accesses to TRCSEQRSTEVR and TRCSEQSTR
+    - coresight: cti: Prevent negative values of enable count
+    - coresight: cti: Add PM runtime call in enable_store
+    - ACPI: resource: Add helper function acpi_dev_get_memory_resources()
+    - usb: typec: intel_pmc_mux: Use the helper acpi_dev_get_memory_resources()
+    - usb: typec: intel_pmc_mux: Don't leak the ACPI device reference count
+    - PCI/IOV: Enlarge virtfn sysfs name buffer
+    - PCI: switchtec: Return -EFAULT for copy_to_user() errors
+    - tty: serial: fsl_lpuart: disable Rx/Tx DMA in lpuart32_shutdown()
+    - tty: serial: fsl_lpuart: clear LPUART Status Register in lpuart32_shutdown()
+    - serial: tegra: Add missing clk_disable_unprepare() in tegra_uart_hw_init()
+    - Revert "char: pcmcia: cm4000_cs: Replace mdelay with usleep_range in
+      set_protocol"
+    - eeprom: idt_89hpesx: Fix error handling in idt_init()
+    - applicom: Fix PCI device refcount leak in applicom_init()
+    - firmware: stratix10-svc: add missing gen_pool_destroy() in
+      stratix10_svc_drv_probe()
+    - VMCI: check context->notify_page after call to get_user_pages_fast() to
+      avoid GPF
+    - misc/mei/hdcp: Use correct macros to initialize uuid_le
+    - driver core: fix resource leak in device_add()
+    - drivers: base: transport_class: fix possible memory leak
+    - drivers: base: transport_class: fix resource leak when
+      transport_add_device() fails
+    - firmware: dmi-sysfs: Fix null-ptr-deref in dmi_sysfs_register_handle
+    - fotg210-udc: Add missing completion handler
+    - dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
+    - usb: early: xhci-dbc: Fix a potential out-of-bound memory access
+    - tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case
+    - RDMA/cxgb4: add null-ptr-check after ip_dev_find()
+    - usb: musb: mediatek: don't unregister something that wasn't registered
+    - usb: gadget: configfs: use to_config_usb_cfg() in os_desc_link()
+    - usb: gadget: configfs: use to_usb_function_instance() in cfg (un)link func
+    - usb: gadget: configfs: remove using list iterator after loop body as a ptr
+    - usb: gadget: configfs: Restrict symlink creation is UDC already binded
+    - iommu/vt-d: Set No Execute Enable bit in PASID table entry
+    - power: supply: remove faulty cooling logic
+    - RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish()
+    - usb: max-3421: Fix setting of I/O pins
+    - RDMA/irdma: Cap MSIX used to online CPUs + 1
+    - serial: fsl_lpuart: fix RS485 RTS polariy inverse issue
+    - tty: serial: imx: Handle RS485 DE signal active high
+    - tty: serial: imx: disable Ageing Timer interrupt request irq
+    - dmaengine: dw-edma: Fix readq_ch() return value truncation
+    - phy: rockchip-typec: fix tcphy_get_mode error case
+    - iw_cxgb4: Fix potential NULL dereference in c4iw_fill_res_cm_id_entry()
+    - iommu: Fix error unwind in iommu_group_alloc()
+    - dmaengine: sf-pdma: pdma_desc memory leak fix
+    - dmaengine: dw-axi-dmac: Do not dereference NULL structure
+    - iommu/vt-d: Fix error handling in sva enable/disable paths
+    - iommu/vt-d: Remove duplicate identity domain flag
+    - iommu/vt-d: Check FL and SL capability sanity in scalable mode
+    - iommu/vt-d: Use second level for GPA->HPA translation
+    - iommu/vt-d: Allow to use flush-queue when first level is default
+    - IB/hfi1: Fix math bugs in hfi1_can_pin_pages()
+    - IB/hfi1: Fix sdma.h tx->num_descs off-by-one errors
+    - remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headers
+    - media: ti: cal: fix possible memory leak in cal_ctx_create()
+    - media: platform: ti: Add missing check for devm_regulator_get
+    - powerpc: Remove linker flag from KBUILD_AFLAGS
+    - s390/vdso: remove -nostdlib compiler flag
+    - s390/vdso: Drop '-shared' from KBUILD_CFLAGS_64
+    - builddeb: clean generated package content
+    - media: max9286: Fix memleak in max9286_v4l2_register()
+    - media: ov2740: Fix memleak in ov2740_init_controls()
+    - media: ov5675: Fix memleak in ov5675_init_controls()
+    - media: i2c: ov772x: Fix memleak in ov772x_probe()
+    - media: i2c: imx219: Split common registers from mode tables
+    - media: i2c: imx219: Fix binning for RAW8 capture
+    - media: v4l2-jpeg: correct the skip count in jpeg_parse_app14_data
+    - media: v4l2-jpeg: ignore the unknown APP14 marker
+    - media: imx-jpeg: Apply clk_bulk api instead of operating specific clk
+    - media: i2c: ov7670: 0 instead of -EINVAL was returned
+    - media: usb: siano: Fix use after free bugs caused by do_submit_urb
+    - media: saa7134: Use video_unregister_device for radio_dev
+    - rpmsg: glink: Avoid infinite loop on intent for missing channel
+    - udf: Define EFSCORRUPTED error code
+    - ARM: dts: exynos: Use Exynos5420 compatible for the MIPI video phy
+    - blk-iocost: fix divide by 0 error in calc_lcoefs()
+    - trace/blktrace: fix memory leak with using debugfs_lookup()
+    - wifi: ath9k: Fix use-after-free in ath9k_hif_usb_disconnect()
+    - wifi: brcmfmac: Fix potential stack-out-of-bounds in brcmf_c_preinit_dcmds()
+    - rcu: Make RCU_LOCKDEP_WARN() avoid early lockdep checks
+    - rcu: Suppress smp_processor_id() complaint in
+      synchronize_rcu_expedited_wait()
+    - rcu-tasks: Make rude RCU-Tasks work well with CPU hotplug
+    - wifi: ath11k: debugfs: fix to work with multiple PCI devices
+    - thermal: intel: Fix unsigned comparison with less than zero
+    - timers: Prevent union confusion from unexpected restart_syscall()
+    - x86/bugs: Reset speculation control settings on init
+    - wifi: brcmfmac: ensure CLM version is null-terminated to prevent stack-out-
+      of-bounds
+    - wifi: mt7601u: fix an integer underflow
+    - inet: fix fast path in __inet_hash_connect()
+    - ice: restrict PTP HW clock freq adjustments to 100, 000, 000 PPB
+    - ice: add missing checks for PF vsi type
+    - ACPI: Don't build ACPICA with '-Os'
+    - thermal: intel: intel_pch: Add support for Wellsburg PCH
+    - clocksource: Suspend the watchdog temporarily when high read latency
+      detected
+    - crypto: hisilicon: Wipe entire pool on error
+    - net: bcmgenet: Add a check for oversized packets
+    - m68k: Check syscall_trace_enter() return code
+    - netfilter: nf_tables: NULL pointer dereference in nf_tables_updobj()
+    - wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
+    - ACPI: video: Fix Lenovo Ideapad Z570 DMI match
+    - net/mlx5: fw_tracer: Fix debug print
+    - coda: Avoid partial allocation of sig_inputArgs
+    - uaccess: Add minimum bounds check on kernel buffer size
+    - s390/idle: mark arch_cpu_idle() noinstr
+    - time/debug: Fix memory leak with using debugfs_lookup()
+    - PM: domains: fix memory leak with using debugfs_lookup()
+    - PM: EM: fix memory leak with using debugfs_lookup()
+    - Bluetooth: btusb: Add VID:PID 13d3:3529 for Realtek RTL8821CE
+    - hv_netvsc: Check status in SEND_RNDIS_PKT completion message
+    - scm: add user copy checks to put_cmsg()
+    - drm/amd/display: Revert Reduce delay when sink device not able to ACK 00340h
+      write
+    - drm/amd/display: Fix potential null-deref in dm_resume
+    - drm/omap: dsi: Fix excessive stack usage
+    - HID: Add Mapping for System Microphone Mute
+    - drm/tiny: ili9486: Do not assume 8-bit only SPI controllers
+    - drm/radeon: free iio for atombios when driver shutdown
+    - scsi: lpfc: Fix use-after-free KFENCE violation during sysfs firmware write
+    - Revert "fbcon: don't lose the console font across generic->chip driver
+      switch"
+    - drm: amd: display: Fix memory leakage
+    - drm/msm/dsi: Add missing check for alloc_ordered_workqueue
+    - docs/scripts/gdb: add necessary make scripts_gdb step
+    - ASoC: soc-compress: Reposition and add pcm_mutex
+    - ASoC: kirkwood: Iterate over array indexes instead of using pointer math
+    - regulator: max77802: Bounds check regulator id against opmode
+    - regulator: s5m8767: Bounds check id indexing into arrays
+    - gfs2: Improve gfs2_make_fs_rw error handling
+    - hwmon: (coretemp) Simplify platform device handling
+    - pinctrl: at91: use devm_kasprintf() to avoid potential leaks
+    - scsi: snic: Fix memory leak with using debugfs_lookup()
+    - HID: logitech-hidpp: Don't restart communication if not necessary
+    - drm: panel-orientation-quirks: Add quirk for Lenovo IdeaPad Duet 3 10IGL5
+    - dm thin: add cond_resched() to various workqueue loops
+    - dm cache: add cond_resched() to various workqueue loops
+    - nfsd: zero out pointers after putting nfsd_files on COPY setup error
+    - drm/shmem-helper: Revert accidental non-GPL export
+    - wifi: rtl8xxxu: fixing transmisison failure for rtl8192eu
+    - firmware: coreboot: framebuffer: Ignore reserved pixel color bits
+    - block: don't allow multiple bios for IOCB_NOWAIT issue
+    - rtc: pm8xxx: fix set-alarm race
+    - ipmi:ssif: resend_msg() cannot fail
+    - ipmi_ssif: Rename idle state and check
+    - s390/extmem: return correct segment type in __segment_load()
+    - s390: discard .interp section
+    - s390/kprobes: fix irq mask clobbering on kprobe reenter from post_handler
+    - s390/kprobes: fix current_kprobe never cleared after kprobes reenter
+    - cifs: Fix uninitialized memory read in smb3_qfs_tcon()
+    - btrfs: hold block group refcount during async discard
+    - locking/rwsem: Prevent non-first waiter from spinning in down_write()
+      slowpath
+    - ksmbd: fix wrong data area length for smb2 lock request
+    - ksmbd: do not allow the actual frame length to be smaller than the rfc1002
+      length
+    - ARM: dts: exynos: correct HDMI phy compatible in Exynos4
+    - hfs: fix missing hfs_bnode_get() in __hfs_bnode_create
+    - fs: hfsplus: fix UAF issue in hfsplus_put_super
+    - exfat: fix reporting fs error when reading dir beyond EOF
+    - exfat: fix unexpected EOF while reading dir
+    - exfat: redefine DIR_DELETED as the bad cluster number
+    - exfat: fix inode->i_blocks for non-512 byte sector size device
+    - fs: dlm: don't set stop rx flag after node reset
+    - fs: dlm: move sending fin message into state change handling
+    - fs: dlm: send FIN ack back in right cases
+    - f2fs: fix information leak in f2fs_move_inline_dirents()
+    - f2fs: fix cgroup writeback accounting with fs-layer encryption
+    - ocfs2: fix defrag path triggering jbd2 ASSERT
+    - ocfs2: fix non-auto defrag path not working issue
+    - selftests/landlock: Skip overlayfs tests when not supported
+    - selftests/landlock: Test ptrace as much as possible with Yama
+    - udf: Truncate added extents on failed expansion
+    - udf: Do not bother merging very long extents
+    - udf: Do not update file length for failed writes to inline files
+    - udf: Preserve link count of system files
+    - udf: Detect system inodes linked into directory hierarchy
+    - udf: Fix file corruption when appending just after end of preallocated
+      extent
+    - RDMA/siw: Fix user page pinning accounting
+    - KVM: Destroy target device if coalesced MMIO unregistration fails
+    - KVM: x86: Inject #GP if WRMSR sets reserved bits in APIC Self-IPI
+    - KVM: SVM: Fix potential overflow in SEV's send|receive_update_data()
+    - KVM: SVM: hyper-v: placate modpost section mismatch error
+    - KVM: s390: disable migration mode when dirty tracking is disabled
+    - x86/virt: Force GIF=1 prior to disabling SVM (for reboot flows)
+    - x86/crash: Disable virt in core NMI crash handler to avoid double shootdown
+    - x86/reboot: Disable virtualization in an emergency if SVM is supported
+    - x86/reboot: Disable SVM, not just VMX, when stopping CPUs
+    - x86/kprobes: Fix __recover_optprobed_insn check optimizing logic
+    - x86/kprobes: Fix arch_check_optimized_kprobe check within optimized_kprobe
+      range
+    - x86/microcode/amd: Remove load_microcode_amd()'s bsp parameter
+    - x86/microcode/AMD: Add a @cpu parameter to the reloading functions
+    - x86/microcode/AMD: Fix mixed steppings support
+    - x86/speculation: Allow enabling STIBP with legacy IBRS
+    - Documentation/hw-vuln: Document the interaction between IBRS and STIBP
+    - brd: return 0/-error from brd_insert_page()
+    - ima: Align ima_file_mmap() parameters with mmap_file LSM hook
+    - irqdomain: Fix association race
+    - irqdomain: Fix disassociation race
+    - irqdomain: Look for existing mapping only once
+    - irqdomain: Drop bogus fwspec-mapping error handling
+    - irqdomain: Fix domain registration race
+    - crypto: qat - fix out-of-bounds read
+    - io_uring: handle TIF_NOTIFY_RESUME when checking for task_work
+    - io_uring: mark task TASK_RUNNING before handling resume/task work
+    - io_uring: add a conditional reschedule to the IOPOLL cancelation loop
+    - io_uring/rsrc: disallow multi-source reg buffers
+    - io_uring: remove MSG_NOSIGNAL from recvmsg
+    - io_uring/poll: allow some retries for poll triggering spuriously
+    - ALSA: ice1712: Do not left ice->gpio_mutex locked in aureon_add_controls()
+    - ALSA: hda/realtek: Add quirk for HP EliteDesk 800 G6 Tower PC
+    - jbd2: fix data missing when reusing bh which is ready to be checkpointed
+    - ext4: optimize ea_inode block expansion
+    - ext4: refuse to create ea block when umounted
+    - mtd: spi-nor: sfdp: Fix index value for SCCR dwords
+    - mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
+    - mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
+    - dm: send just one event on resize, not two
+    - dm: add cond_resched() to dm_wq_work()
+    - wifi: rtl8xxxu: Use a longer retry limit of 48
+    - wifi: ath11k: allow system suspend to survive ath11k
+    - wifi: cfg80211: Fix use after free for wext
+    - qede: fix interrupt coalescing configuration
+    - thermal: intel: powerclamp: Fix cur_state for multi package system
+    - dm flakey: fix logic when corrupting a bio
+    - dm flakey: don't corrupt the zero page
+    - dm flakey: fix a bug with 32-bit highmem systems
+    - ARM: dts: qcom: sdx55: Add Qcom SMMU-500 as the fallback for IOMMU node
+    - ARM: dts: exynos: correct TMU phandle in Exynos4210
+    - ARM: dts: exynos: correct TMU phandle in Exynos4
+    - ARM: dts: exynos: correct TMU phandle in Odroid XU3 family
+    - ARM: dts: exynos: correct TMU phandle in Exynos5250
+    - ARM: dts: exynos: correct TMU phandle in Odroid XU
+    - ARM: dts: exynos: correct TMU phandle in Odroid HC1
+    - fuse: add inode/permission checks to fileattr_get/fileattr_set
+    - rbd: avoid use-after-free in do_rbd_add() when rbd_dev_create() fails
+    - ceph: update the time stamps and try to drop the suid/sgid
+    - alpha: fix FEN fault handling
+    - dax/kmem: Fix leak of memory-hotplug resources
+    - mips: fix syscall_get_nr
+    - media: ipu3-cio2: Fix PM runtime usage_count in driver unbind
+    - remoteproc/mtk_scp: Move clk ops outside send_lock
+    - docs: gdbmacros: print newest record
+    - mm: memcontrol: deprecate charge moving
+    - mm/thp: check and bail out if page in deferred queue already
+    - ktest.pl: Give back console on Ctrt^C on monitor
+    - ktest.pl: Fix missing "end_monitor" when machine check fails
+    - ktest.pl: Add RUN_TIMEOUT option with default unlimited
+    - ring-buffer: Handle race between rb_move_tail and rb_check_pages
+    - tools/bootconfig: fix single & used for logical condition
+    - scsi: qla2xxx: Fix link failure in NPIV environment
+    - scsi: qla2xxx: Check if port is online before sending ELS
+    - scsi: qla2xxx: Fix DMA-API call trace on NVMe LS requests
+    - scsi: qla2xxx: Remove unintended flag clearing
+    - scsi: qla2xxx: Fix erroneous link down
+    - scsi: qla2xxx: Remove increment of interface err cnt
+    - scsi: ses: Don't attach if enclosure has no components
+    - scsi: ses: Fix slab-out-of-bounds in ses_enclosure_data_process()
+    - scsi: ses: Fix possible addl_desc_ptr out-of-bounds accesses
+    - scsi: ses: Fix possible desc_ptr out-of-bounds accesses
+    - scsi: ses: Fix slab-out-of-bounds in ses_intf_remove()
+    - RISC-V: add a spin_shadow_stack declaration
+    - riscv: mm: fix regression due to update_mmu_cache change
+    - riscv: jump_label: Fixup unaligned arch_static_branch function
+    - riscv, mm: Perform BPF exhandler fixup on page fault
+    - riscv: ftrace: Remove wasted nops for !RISCV_ISA_C
+    - riscv: ftrace: Reduce the detour code size to half
+    - MIPS: DTS: CI20: fix otg power gpio
+    - PCI/PM: Observe reset delay irrespective of bridge_d3
+    - PCI: hotplug: Allow marking devices as disconnected during bind/unbind
+    - PCI: Avoid FLR for AMD FCH AHCI adapters
+    - iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
+    - vfio/type1: prevent underflow of locked_vm via exec()
+    - vfio/type1: track locked_vm per dma
+    - vfio/type1: restore locked_vm
+    - drm/i915/quirks: Add inverted backlight quirk for HP 14-r206nv
+    - drm/radeon: Fix eDP for single-display iMac11,2
+    - drm/edid: fix AVI infoframe aspect ratio handling
+    - perf intel-pt: pkt-decoder: Add CFE and EVD packets
+    - qede: avoid uninitialized entries in coal_entry array
+    - media: uvcvideo: Fix memory leak of object map on error exit path
+    - iommu/vt-d: Fix an unbalanced rcu_read_lock/rcu_read_unlock()
+    - arm64: dts: qcom: ipq8074: fix Gen2 PCIe QMP PHY
+    - wifi: ath9k: use proper statements in conditionals
+    - kbuild: Port silent mode detection to future gnu make.
+    - Linux 5.15.99
+    - [Config] Stop expecting mxsfb for ppc64el
+
+  * Use new annotations model (LP: #2019000)
+    - [Packaging] new annotations model infrastructure
+    - [Config] migrate all configs into annotations
+
+  * CVE-2023-30456
+    - KVM: nVMX: add missing consistency checks for CR0 and CR4
+
+  * CVE-2023-1859
+    - 9p/xen : Fix use after free bug in xen_9pfs_front_remove due to race
+      condition
+
+  * CVE-2023-1670
+    - xirc2ps_cs: Fix use after free bug in xirc2ps_detach
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 12 May 2023 16:52:42 +0200
+
+linux (5.15.0-72.79) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-72.79 -proposed tracker (LP: #2016548)
+
+  * Add split lock detection for EMR (LP: #2015855)
+    - x86/split_lock: Enumerate architectural split lock disable bit
+
+  *  selftest: fib_tests: Always cleanup before exit  (LP: #2015956)
+    - selftest: fib_tests: Always cleanup before exit
+
+  * Add support for intel EMR cpu (LP: #2015372)
+    - platform/x86: intel-uncore-freq: add Emerald Rapids support
+    - perf/x86/intel/cstate: Add Emerald Rapids
+    - perf/x86/rapl: Add support for Intel Emerald Rapids
+    - intel_idle: add Emerald Rapids Xeon support
+    - tools/power/x86/intel-speed-select: Add Emerald Rapid quirk
+    - tools/power turbostat: Introduce support for EMR
+    - powercap: intel_rapl: add support for Emerald Rapids
+    - EDAC/i10nm: Add Intel Emerald Rapids server support
+
+  * Kernel livepatch ftrace graph fix (LP: #2013603)
+    - kprobes: treewide: Remove trampoline_address from
+      kretprobe_trampoline_handler()
+    - kprobes: treewide: Make it harder to refer kretprobe_trampoline directly
+    - kprobes: Add kretprobe_find_ret_addr() for searching return address
+    - s390/unwind: recover kretprobe modified return address in stacktrace
+    - s390/unwind: fix fgraph return address recovery
+
+  * Jammy update: v5.15.98 upstream stable release (LP: #2015600)
+    - Linux 5.15.98
+
+  * Jammy update: v5.15.97 upstream stable release (LP: #2015599)
+    - ionic: refactor use of ionic_rx_fill()
+    - Fix XFRM-I support for nested ESP tunnels
+    - arm64: dts: rockchip: drop unused LED mode property from rk3328-roc-cc
+    - ARM: dts: rockchip: add power-domains property to dp node on rk3288
+    - HID: elecom: add support for TrackBall 056E:011C
+    - ACPI: NFIT: fix a potential deadlock during NFIT teardown
+    - btrfs: send: limit number of clones and allocated memory size
+    - ASoC: rt715-sdca: fix clock stop prepare timeout issue
+    - IB/hfi1: Assign npages earlier
+    - neigh: make sure used and confirmed times are valid
+    - HID: core: Fix deadloop in hid_apply_multiplier.
+    - x86/cpu: Add Lunar Lake M
+    - staging: mt7621-dts: change palmbus address to lower case
+    - bpf: bpf_fib_lookup should not return neigh in NUD_FAILED state
+    - net: Remove WARN_ON_ONCE(sk->sk_forward_alloc) from sk_stream_kill_queues().
+    - vc_screen: don't clobber return value in vcs_read
+    - scripts/tags.sh: Invoke 'realpath' via 'xargs'
+    - scripts/tags.sh: fix incompatibility with PCRE2
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-M
+    - USB: serial: option: add support for VW/Skoda "Carstick LTE"
+    - usb: gadget: u_serial: Add null pointer check in gserial_resume
+    - USB: core: Don't hold device lock while reading the "descriptors" sysfs file
+    - Linux 5.15.97
+
+  * Jammy update: v5.15.96 upstream stable release (LP: #2015595)
+    - drm/etnaviv: don't truncate physical page address
+    - wifi: rtl8xxxu: gen2: Turn on the rate control
+    - drm/edid: Fix minimum bpc supported with DSC1.2 for HDMI sink
+    - clk: mxl: Switch from direct readl/writel based IO to regmap based IO
+    - clk: mxl: Remove redundant spinlocks
+    - clk: mxl: Add option to override gate clks
+    - clk: mxl: Fix a clk entry by adding relevant flags
+    - powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
+    - clk: mxl: syscon_node_to_regmap() returns error pointers
+    - random: always mix cycle counter in add_latent_entropy()
+    - KVM: x86: Fail emulation during EMULTYPE_SKIP on any exception
+    - KVM: SVM: Skip WRMSR fastpath on VM-Exit if next RIP isn't valid
+    - can: kvaser_usb: hydra: help gcc-13 to figure out cmd_len
+    - powerpc: dts: t208x: Disable 10G on MAC1 and MAC2
+    - powerpc: use generic version of arch_is_kernel_initmem_freed()
+    - powerpc/vmlinux.lds: Ensure STRICT_ALIGN_SIZE is at least page aligned
+    - powerpc/vmlinux.lds: Add an explicit symbol for the SRWX boundary
+    - powerpc/64s/radix: Fix crash with unaligned relocated kernel
+    - powerpc/64s/radix: Fix RWX mapping with relocated kernel
+    - drm/i915/gvt: fix double free bug in split_2MB_gtt_entry
+    - uaccess: Add speculation barrier to copy_from_user()
+    - binder: read pre-translated fds from sender buffer
+    - binder: defer copies of pre-patched txn data
+    - binder: fix pointer cast warning
+    - binder: Address corner cases in deferred copy and fixup
+    - binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0
+    - nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
+    - wifi: mwifiex: Add missing compatible string for SD8787
+    - audit: update the mailing list in MAINTAINERS
+    - ext4: Fix function prototype mismatch for ext4_feat_ktype
+    - bpf: add missing header file include
+    - Linux 5.15.96
+
+  * Debian autoreconstruct Fix restoration of execute permissions (LP: #2015498)
+    - [Debian] autoreconstruct - fix restoration of execute permissions
+
+  * kernel: fix __clear_user() inline assembly constraints (LP: #2013088)
+    - s390/uaccess: add missing earlyclobber annotations to __clear_user()
+
+  * Kernel crash during Mellanox performance testing (LP: #2015097)
+    - net/mlx5: fs, refactor software deletion rule
+
+  * expoline.o is packaged unconditionally for s390x (LP: #2013209)
+    - [Packaging] Copy expoline.o only when produced by the build
+
+  * Intel E810 NICs driver in causing hangs when booting and bonds configured
+    (LP: #2004262)
+    - ice: avoid bonding causing auxiliary plug/unplug under RTNL lock
+
+  * Jammy update: v5.15.95 upstream stable release (LP: #2013118)
+    - mptcp: fix locking for in-kernel listener creation
+    - kprobes: treewide: Cleanup the error messages for kprobes
+    - riscv: kprobe: Fixup misaligned load text
+    - ACPI / x86: Add support for LPS0 callback handler
+    - ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
+    - ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
+    - selftests/bpf: Verify copy_register_state() preserves parent/live fields
+    - ALSA: hda: Do not unset preset when cleaning up codec
+    - bpf, sockmap: Don't let sock_map_{close,destroy,unhash} call itself
+    - ASoC: cs42l56: fix DT probe
+    - tools/virtio: fix the vringh test for virtio ring changes
+    - net/rose: Fix to not accept on connected socket
+    - net: stmmac: do not stop RX_CLK in Rx LPI state for qcs404 SoC
+    - drm/nouveau/devinit/tu102-: wait for GFW_BOOT_PROGRESS == COMPLETED
+    - net: sched: sch: Bounds check priority
+    - s390/decompressor: specify __decompress() buf len to avoid overflow
+    - nvme-fc: fix a missing queue put in nvmet_fc_ls_create_association
+    - drm/amd/display: Properly handle additional cases where DCN is not supported
+    - platform/x86: touchscreen_dmi: Add Chuwi Vi8 (CWI501) DMI match
+    - nvmem: core: add error handling for dev_set_name
+    - nvmem: core: fix cleanup after dev_set_name()
+    - nvmem: core: fix registration vs use race
+    - nvmem: core: fix return value
+    - xfs: zero inode fork buffer at allocation
+    - xfs: fix potential log item leak
+    - xfs: detect self referencing btree sibling pointers
+    - xfs: set XFS_FEAT_NLINK correctly
+    - xfs: validate v5 feature fields
+    - xfs: avoid unnecessary runtime sibling pointer endian conversions
+    - xfs: don't assert fail on perag references on teardown
+    - xfs: assert in xfs_btree_del_cursor should take into account error
+    - xfs: purge dquots after inode walk fails during quotacheck
+    - xfs: don't leak btree cursor when insrec fails after a split
+    - mptcp: do not wait for bare sockets' timeout
+    - aio: fix mremap after fork null-deref
+    - drm/amd/display: Fail atomic_check early on normalize_zpos error
+    - platform/x86: amd-pmc: Fix compilation when CONFIG_DEBUGFS is disabled
+    - platform/x86: amd-pmc: Correct usage of SMU version
+    - platform/x86/amd: pmc: Disable IRQ1 wakeup for RN/CZN
+    - netfilter: nft_tproxy: restrict to prerouting hook
+    - tcp: Fix listen() regression in 5.15.88.
+    - mmc: jz4740: Work around bug on JZ4760(B)
+    - mmc: sdio: fix possible resource leaks in some error paths
+    - mmc: mmc_spi: fix error handling in mmc_spi_probe()
+    - ALSA: hda/conexant: add a new hda codec SN6180
+    - ALSA: hda/realtek - fixed wrong gpio assigned
+    - sched/psi: Fix use-after-free in ep_remove_wait_queue()
+    - hugetlb: check for undefined shift on 32 bit architectures
+    - of: reserved_mem: Have kmemleak ignore dynamically allocated reserved mem
+    - selftest/lkdtm: Skip stack-entropy test if lkdtm is not available
+    - net: Fix unwanted sign extension in netdev_stats_to_stats64()
+    - revert "squashfs: harden sanity check in squashfs_read_xattr_id_table"
+    - ixgbe: allow to increase MTU to 3K with XDP enabled
+    - i40e: add double of VLAN header when computing the max MTU
+    - net: bgmac: fix BCM5358 support by setting correct flags
+    - net: ethernet: ti: am65-cpsw: Add RX DMA Channel Teardown Quirk
+    - sctp: sctp_sock_filter(): avoid list_entry() on possibly empty list
+    - dccp/tcp: Avoid negative sk_forward_alloc by ipv6_pinfo.pktoptions.
+    - net/usb: kalmia: Don't pass act_len in usb_bulk_msg error path
+    - net: openvswitch: fix possible memory leak in ovs_meter_cmd_set()
+    - net: stmmac: fix order of dwmac5 FlexPPS parametrization sequence
+    - bnxt_en: Fix mqprio and XDP ring checking logic
+    - net: stmmac: Restrict warning on disabling DMA store and fwd mode
+    - ixgbe: add double of VLAN header when computing the max MTU
+    - ipv6: Fix datagram socket connection with DSCP.
+    - ipv6: Fix tcp socket connection with DSCP.
+    - nilfs2: fix underflow in second superblock position calculations
+    - mm/filemap: fix page end in filemap_get_read_batch
+    - drm/i915/gen11: Moving WAs to icl_gt_workarounds_init()
+    - drm/i915/gen11: Wa_1408615072/Wa_1407596294 should be on GT list
+    - flow_offload: fill flags to action structure
+    - net/sched: act_ctinfo: use percpu stats
+    - i40e: Add checking for null for nlmsg_find_attr()
+    - kvm: initialize all of the kvm_debugregs structure before sending it to
+      userspace
+    - alarmtimer: Prevent starvation by small intervals and SIG_IGN
+    - ASoC: SOF: Intel: hda-dai: fix possible stream_tag leak
+    - net: sched: sch: Fix off by one in htb_activate_prios()
+    - platform/x86/amd: pmc: add CONFIG_SERIO dependency
+    - Linux 5.15.95
+
+  * CVE-2023-1075
+    - net/tls: tls_is_tx_ready() checked list_entry
+
+  * devlink_port_split from ubuntu_kernel_selftests.net fails on hirsute
+    (KeyError: 'flavour') (LP: #1937133)
+    - selftests: net: devlink_port_split.py: skip test if no suitable device
+      available
+
+  * Connection timeout due to conntrack limits (LP: #2011616)
+    - netfilter: conntrack: adopt safer max chain length
+
+  * Jammy update: v5.15.94 upstream stable release (LP: #2012673)
+    - mm/migration: return errno when isolate_huge_page failed
+    - migrate: hugetlb: check for hugetlb shared PMD in node migration
+    - btrfs: limit device extents to the device size
+    - btrfs: zlib: zero-initialize zlib workspace
+    - ALSA: hda/realtek: Add Positivo N14KP6-TG
+    - ALSA: emux: Avoid potential array out-of-bound in snd_emux_xg_control()
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro 360
+    - ALSA: hda/realtek: Enable mute/micmute LEDs on HP Elitebook, 645 G9
+    - tracing: Fix poll() and select() do not work on per_cpu trace_pipe and
+      trace_pipe_raw
+    - of/address: Return an error when no valid dma-ranges are found
+    - can: j1939: do not wait 250 ms if the same addr was already claimed
+    - xfrm: compat: change expression for switch in xfrm_xlate64
+    - IB/hfi1: Restore allocated resources on failed copyout
+    - xfrm/compat: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
+    - IB/IPoIB: Fix legacy IPoIB due to wrong number of queues
+    - RDMA/irdma: Fix potential NULL-ptr-dereference
+    - RDMA/usnic: use iommu_map_atomic() under spin_lock()
+    - xfrm: fix bug with DSCP copy to v6 from v4 tunnel
+    - net: phylink: move phy_device_free() to correctly release phy device
+    - bonding: fix error checking in bond_debug_reregister()
+    - net: phy: meson-gxl: use MMD access dummy stubs for GXL, internal PHY
+    - ionic: clean interrupt before enabling queue to avoid credit race
+    - uapi: add missing ip/ipv6 header dependencies for linux/stddef.h
+    - ice: Do not use WQ_MEM_RECLAIM flag for workqueue
+    - net: dsa: mt7530: don't change PVC_EG_TAG when CPU port becomes VLAN-aware
+    - net: mscc: ocelot: fix VCAP filters not matching on MAC with "protocol
+      802.1Q"
+    - net/mlx5e: Move repeating clear_bit in mlx5e_rx_reporter_err_rq_cqe_recover
+    - net/mlx5e: Introduce the mlx5e_flush_rq function
+    - net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
+    - net/mlx5: Bridge, fix ageing of peer FDB entries
+    - net/mlx5e: IPoIB, Show unknown speed instead of error
+    - net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
+    - net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
+    - net/mlx5: Serialize module cleanup with reload and remove
+    - igc: Add ndo_tx_timeout support
+    - rds: rds_rm_zerocopy_callback() use list_first_entry()
+    - selftests: forwarding: lib: quote the sysctl values
+    - ALSA: pci: lx6464es: fix a debug loop
+    - riscv: stacktrace: Fix missing the first frame
+    - ASoC: topology: Return -ENOMEM on memory allocation failure
+    - pinctrl: mediatek: Fix the drive register definition of some Pins
+    - pinctrl: aspeed: Fix confusing types in return value
+    - pinctrl: single: fix potential NULL dereference
+    - spi: dw: Fix wrong FIFO level setting for long xfers
+    - pinctrl: intel: Restore the pins that used to be in Direct IRQ mode
+    - cifs: Fix use-after-free in rdata->read_into_pages()
+    - net: USB: Fix wrong-direction WARNING in plusb.c
+    - mptcp: be careful on subflow status propagation on errors
+    - btrfs: free device in btrfs_close_devices for a single device filesystem
+    - usb: core: add quirk for Alcor Link AK9563 smartcard reader
+    - usb: typec: altmodes/displayport: Fix probe pin assign check
+    - clk: ingenic: jz4760: Update M/N/OD calculation algorithm
+    - ceph: flush cap releases when the session is flushed
+    - riscv: Fixup race condition on PG_dcache_clean in flush_icache_pte
+    - powerpc/64s/interrupt: Fix interrupt exit race with security mitigation
+      switch
+    - rtmutex: Ensure that the top waiter is always woken up
+    - arm64: dts: meson-gx: Make mmc host controller interrupts level-sensitive
+    - arm64: dts: meson-g12-common: Make mmc host controller interrupts level-
+      sensitive
+    - arm64: dts: meson-axg: Make mmc host controller interrupts level-sensitive
+    - Fix page corruption caused by racy check in __free_pages
+    - drm/amdgpu/fence: Fix oops due to non-matching drm_sched init/fini
+    - drm/i915: Initialize the obj flags for shmem objects
+    - drm/i915: Fix VBT DSI DVO port handling
+    - x86/speculation: Identify processors vulnerable to SMT RSB predictions
+    - KVM: x86: Mitigate the cross-thread return address predictions bug
+    - Documentation/hw-vuln: Add documentation for Cross-Thread Return Predictions
+    - Linux 5.15.94
+
+  * Jammy update: v5.15.93 upstream stable release (LP: #2012665)
+    - firewire: fix memory leak for payload of request subaction to IEC 61883-1
+      FCP region
+    - bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()
+    - ASoC: Intel: boards: fix spelling in comments
+    - ASoC: Intel: bytcht_es8316: move comment to the right place
+    - ASoC: Intel: bytcht_es8316: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_rt5651: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_rt5640: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_wm5102: Drop reference count of ACPI device after use
+    - bpf: Fix a possible task gone issue with bpf_send_signal[_thread]() helpers
+    - ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
+    - bpf: Support <8-byte scalar spill and refill
+    - bpf: Fix to preserve reg parent/live fields when copying range info
+    - bpf, sockmap: Check for any of tcp_bpf_prots when cloning a listener
+    - arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
+    - drm/vc4: hdmi: make CEC adapter name unique
+    - scsi: Revert "scsi: core: map PQ=1, PDT=other values to
+      SCSI_SCAN_TARGET_PRESENT"
+    - vhost/net: Clear the pending messages when the backend is removed
+    - WRITE is "data source", not destination...
+    - READ is "data destination", not source...
+    - fix iov_iter_bvec() "direction" argument
+    - fix "direction" argument of iov_iter_kvec()
+    - ice: Prevent set_channel from changing queues while RDMA active
+    - qede: execute xdp_do_flush() before napi_complete_done()
+    - virtio-net: execute xdp_do_flush() before napi_complete_done()
+    - dpaa_eth: execute xdp_do_flush() before napi_complete_done()
+    - dpaa2-eth: execute xdp_do_flush() before napi_complete_done()
+    - sfc: correctly advertise tunneled IPv6 segmentation
+    - net: phy: dp83822: Fix null pointer access on DP83825/DP83826 devices
+    - block/bfq-iosched.c: use "false" rather than "BLK_RW_ASYNC"
+    - block, bfq: replace 0/1 with false/true in bic apis
+    - block, bfq: fix uaf for bfqq in bic_set_bfqq()
+    - netrom: Fix use-after-free caused by accept on already connected socket
+    - drm/i915/guc: Fix locking when searching for a hung request
+    - drm/i915/adlp: Fix typo for reference clock
+    - netfilter: br_netfilter: disable sabotage_in hook after first suppression
+    - squashfs: harden sanity check in squashfs_read_xattr_id_table
+    - net: phy: meson-gxl: Add generic dummy stubs for MMD register access
+    - ip/ip6_gre: Fix changing addr gen mode not generating IPv6 link local
+      address
+    - ip/ip6_gre: Fix non-point-to-point tunnel not generating IPv6 link local
+      address
+    - riscv: kprobe: Fixup kernel panic when probing an illegal position
+    - igc: return an error if the mac type is unknown in
+      igc_ptp_systim_to_hwtstamp()
+    - can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
+    - ata: libata: Fix sata_down_spd_limit() when no link speed is reported
+    - selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
+    - selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
+    - selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy
+      benchmarking
+    - virtio-net: Keep stop() to follow mirror sequence of open()
+    - net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
+    - efi: fix potential NULL deref in efi_mem_reserve_persistent
+    - i2c: designware-pci: Add new PCI IDs for AMD NAVI GPU
+    - i2c: mxs: suppress probe-deferral error message
+    - scsi: target: core: Fix warning on RT kernels
+    - perf/x86/intel: Add Emerald Rapids
+    - scsi: iscsi_tcp: Fix UAF during logout when accessing the shost ipaddress
+    - scsi: iscsi_tcp: Fix UAF during login when accessing the shost ipaddress
+    - i2c: rk3x: fix a bunch of kernel-doc warnings
+    - platform/x86: gigabyte-wmi: add support for B450M DS3H WIFI-CF
+    - net/x25: Fix to not accept on connected socket
+    - drm/amd/display: Fix timing not changning when freesync video is enabled
+    - iio: adc: stm32-dfsdm: fill module aliases
+    - usb: dwc3: qcom: enable vbus override when in OTG dr-mode
+    - usb: gadget: f_fs: Fix unbalanced spinlock in __ffs_ep0_queue_wait
+    - vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF
+    - Input: i8042 - add Clevo PCX0DX to i8042 quirk table
+    - fbcon: Check font dimension limits
+    - net: qrtr: free memory on error path in radix_tree_insert()
+    - watchdog: diag288_wdt: do not use stack buffers for hardware data
+    - watchdog: diag288_wdt: fix __diag288() inline assembly
+    - ALSA: hda/realtek: Add Acer Predator PH315-54
+    - efi: Accept version 2 of memory attributes table
+    - iio: hid: fix the retval in accel_3d_capture_sample
+    - iio: hid: fix the retval in gyro_3d_capture_sample
+    - iio: adc: berlin2-adc: Add missing of_node_put() in error path
+    - iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
+    - iio: imu: fxos8700: fix ACCEL measurement range selection
+    - iio: imu: fxos8700: fix incomplete ACCEL and MAGN channels readback
+    - iio: imu: fxos8700: fix IMU data bits returned to user space
+    - iio: imu: fxos8700: fix map label of channel type to MAGN sensor
+    - iio: imu: fxos8700: fix swapped ACCEL and MAGN channels readback
+    - iio: imu: fxos8700: fix incorrect ODR mode readback
+    - iio: imu: fxos8700: fix failed initialization ODR mode assignment
+    - iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
+    - iio: imu: fxos8700: fix MAGN sensor scale and unit
+    - nvmem: qcom-spmi-sdam: fix module autoloading
+    - parisc: Fix return code of pdc_iodc_print()
+    - parisc: Wire up PTRACE_GETREGS/PTRACE_SETREGS for compat case
+    - riscv: disable generation of unwind tables
+    - mm: hugetlb: proc: check for hugetlb shared PMD in /proc/PID/smaps
+    - usb: gadget: f_uac2: Fix incorrect increment of bNumEndpoints
+    - kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
+    - x86/debug: Fix stack recursion caused by wrongly ordered DR7 accesses
+    - fpga: stratix10-soc: Fix return value check in s10_ops_write_init()
+    - mm/swapfile: add cond_resched() in get_swap_pages()
+    - highmem: round down the address passed to kunmap_flush_on_unmap()
+    - Squashfs: fix handling and sanity checking of xattr_ids count
+    - drm/i915: Fix potential bit_17 double-free
+    - nvmem: core: initialise nvmem->id early
+    - nvmem: core: remove nvmem_config wp_gpio
+    - nvmem: core: fix cell removal on error
+    - serial: 8250_dma: Fix DMA Rx completion race
+    - serial: 8250_dma: Fix DMA Rx rearm race
+    - phy: qcom-qmp-combo: disable runtime PM on unbind
+    - phy: qcom-qmp-combo: fix memleak on probe deferral
+    - phy: qcom-qmp-usb: fix memleak on probe deferral
+    - phy: qcom-qmp-combo: fix broken power on
+    - phy: qcom-qmp-combo: fix runtime suspend
+    - bpf: Fix incorrect state pruning for <8B spill/fill
+    - bpf: Do not reject when the stack read size is different from the tracked
+      scalar size
+    - iio:adc:twl6030: Enable measurement of VAC
+    - powerpc/imc-pmu: Revert nest_init_lock to being a mutex
+    - fs/ntfs3: Validate attribute data and valid sizes
+    - ovl: Use "buf" flexible array for memcpy() destination
+    - fbdev: smscufx: fix error handling code in ufx_usb_probe
+    - f2fs: fix to do sanity check on i_extra_isize in is_alive()
+    - wifi: brcmfmac: Check the count value of channel spec to prevent out-of-
+      bounds reads
+    - gfs2: Cosmetic gfs2_dinode_{in,out} cleanup
+    - gfs2: Always check inode size of inline inodes
+    - bpf: Skip invalid kfunc call in backtrack_insn
+    - Linux 5.15.93
+
+  * CVE-2023-1118
+    - media: rc: Fix use-after-free bugs caused by ene_tx_irqsim()
+
+  * [SRU][Ubuntu 22.04.1]: Observed "Array Index out of bounds" Call Trace
+    multiple times on Ubuntu 22.04.1 OS during boot (LP: #2008157)
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_FW_RAID_MAP
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_FW_RAID_MAP_DYNAMIC
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_DRV_RAID_MAP
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_PD_CFG_SEQ_NUM_SYNC
+    - scsi: megaraid_sas: Use struct_size() in code related to struct
+      MR_FW_RAID_MAP
+    - scsi: megaraid_sas: Use struct_size() in code related to struct
+      MR_PD_CFG_SEQ_NUM_SYNC
+
+  * Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo
+    child qdiscs" (LP: #2011926)
+    - Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo
+      child qdiscs"
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 18 Apr 2023 16:42:38 +0200
+
+linux (5.15.0-71.78) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-71.78 -proposed tracker (LP: #2016820)
+
+  * CVE-2023-1872
+    - io_uring: add missing lock in io_get_file_fixed
+    - io_uring: ensure that io_init_req() passes in the right issue_flags
+
+  * CVE-2023-1829
+    - net/sched: Retire tcindex classifier
+    - [Config]: Make sure CONFIG_NET_CLS_TCINDEX is not available
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Tue, 18 Apr 2023 05:37:02 -0300
+
+linux (5.15.0-70.77) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-70.77 -proposed tracker (LP: #2011918)
+
+  * CVE-2023-26545
+    - net: mpls: fix stale pointer if allocation fails during device rename
+
+  * CVE-2023-1281
+    - net/sched: tcindex: update imperfect hash filters respecting rcu
+
+  * [SRU][Ubuntu 22.04.1] mpi3mr: Add management application interface(BSG)
+    support (LP: #1971151)
+    - scsi: mpi3mr: Add bsg device support
+    - scsi: mpi3mr: Add support for driver commands
+    - scsi: mpi3mr: Move data structures/definitions from MPI headers to uapi
+      header
+    - scsi: mpi3mr: Add support for MPT commands
+    - scsi: mpi3mr: Add support for PEL commands
+    - scsi: mpi3mr: Expose adapter state to sysfs
+    - scsi: mpi3mr: Add support for NVMe passthrough
+    - scsi: mpi3mr: Update driver version to 8.0.0.69.0
+    - scsi: mpi3mr: Increase I/O timeout value to 60s
+    - scsi: mpi3mr: Hidden drives not removed during soft reset
+    - scsi: mpi3mr: Return I/Os to an unrecoverable HBA with DID_ERROR
+    - scsi: mpi3mr: Fix a NULL vs IS_ERR() bug in mpi3mr_bsg_init()
+    - scsi: mpi3mr: Return error if dma_alloc_coherent() fails
+    - scsi: mpi3mr: Add shost related sysfs attributes
+    - scsi: mpi3mr: Add target device related sysfs attributes
+    - scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
+    - scsi: mpi3mr: Fix kernel-doc
+
+  * cpufreq: intel_pstate: Update Balance performance EPP for Sapphire Rapids
+    (LP: #2008519)
+    - cpufreq: intel_pstate: Update EPP for AlderLake mobile
+    - cpufreq: intel_pstate: Adjust balance_performance EPP for Sapphire Rapids
+
+  * Fail to output sound to external monitor which connects via docking station
+    (LP: #2009024)
+    - [Config] Enable CONFIG_SND_HDA_INTEL_HDMI_SILENT_STREAM
+
+  * Fix mediatek wifi driver crash when loading wrong SAR table (LP: #2009118)
+    - wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
+
+  * Jammy update: v5.15.92 upstream stable release (LP: #2011472)
+    - ARM: dts: imx: Fix pca9547 i2c-mux node name
+    - ARM: dts: vf610: Fix pca9548 i2c-mux node names
+    - arm64: dts: freescale: Fix pca954x i2c-mux node names
+    - arm64: dts: imx8mq-thor96: fix no-mmc property for SDHCI
+    - firmware: arm_scmi: Clear stale xfer->hdr.status
+    - bpf: Skip task with pid=1 in send_signal_common()
+    - erofs/zmap.c: Fix incorrect offset calculation
+    - blk-cgroup: fix missing pd_online_fn() while activating policy
+    - HID: playstation: sanity check DualSense calibration data.
+    - dmaengine: imx-sdma: Fix a possible memory leak in sdma_transfer_init
+    - cifs: fix return of uninitialized rc in dfs_cache_update_tgthint()
+    - extcon: usbc-tusb320: fix kernel-doc warning
+    - Bluetooth: fix null ptr deref on hci_sync_conn_complete_evt
+    - tools: fix ARRAY_SIZE defines in tools and selftests hdrs
+    - selftests/vm: remove ARRAY_SIZE define from individual tests
+    - selftests: Provide local define of __cpuid_count()
+    - net: fix NULL pointer in skb_segment_list
+    - net: mctp: purge receive queues on sk destruction
+    - Linux 5.15.92
+
+  * Jammy update: v5.15.91 upstream stable release (LP: #2011467)
+    - memory: tegra: Remove clients SID override programming
+    - memory: atmel-sdramc: Fix missing clk_disable_unprepare in
+      atmel_ramc_probe()
+    - memory: mvebu-devbus: Fix missing clk_disable_unprepare in
+      mvebu_devbus_probe()
+    - dmaengine: ti: k3-udma: Do conditional decrement of
+      UDMA_CHAN_RT_PEER_BCNT_REG
+    - arm64: dts: imx8mp-phycore-som: Remove invalid PMIC property
+    - ARM: dts: imx6ul-pico-dwarf: Use 'clock-frequency'
+    - ARM: dts: imx7d-pico: Use 'clock-frequency'
+    - ARM: dts: imx6qdl-gw560x: Remove incorrect 'uart-has-rtscts'
+    - arm64: dts: imx8mm-beacon: Fix ecspi2 pinmux
+    - ARM: imx: add missing of_node_put()
+    - HID: intel_ish-hid: Add check for ishtp_dma_tx_map
+    - arm64: dts: imx8mm-venice-gw7901: fix USB2 controller OC polarity
+    - soc: imx8m: Fix incorrect check for of_clk_get_by_name()
+    - reset: uniphier-glue: Use reset_control_bulk API
+    - reset: uniphier-glue: Fix possible null-ptr-deref
+    - EDAC/highbank: Fix memory leak in highbank_mc_probe()
+    - firmware: arm_scmi: Harden shared memory access in fetch_response
+    - firmware: arm_scmi: Harden shared memory access in fetch_notification
+    - tomoyo: fix broken dependency on *.conf.default
+    - RDMA/core: Fix ib block iterator counter overflow
+    - IB/hfi1: Reject a zero-length user expected buffer
+    - IB/hfi1: Reserve user expected TIDs
+    - IB/hfi1: Fix expected receive setup error exit issues
+    - IB/hfi1: Immediately remove invalid memory from hardware
+    - IB/hfi1: Remove user expected buffer invalidate race
+    - affs: initialize fsdata in affs_truncate()
+    - PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
+    - arm64: dts: qcom: msm8992: Don't use sfpb mutex
+    - arm64: dts: qcom: msm8992-libra: Add CPU regulators
+    - arm64: dts: qcom: msm8992-libra: Fix the memory map
+    - phy: ti: fix Kconfig warning and operator precedence
+    - NFSD: fix use-after-free in nfsd4_ssc_setup_dul()
+    - ARM: dts: at91: sam9x60: fix the ddr clock for sam9x60
+    - amd-xgbe: TX Flow Ctrl Registers are h/w ver dependent
+    - amd-xgbe: Delay AN timeout during KR training
+    - bpf: Fix pointer-leak due to insufficient speculative store bypass
+      mitigation
+    - phy: rockchip-inno-usb2: Fix missing clk_disable_unprepare() in
+      rockchip_usb2phy_power_on()
+    - net: nfc: Fix use-after-free in local_cleanup()
+    - net: wan: Add checks for NULL for utdm in undo_uhdlc_init and unmap_si_regs
+    - net: enetc: avoid deadlock in enetc_tx_onestep_tstamp()
+    - sch_htb: Avoid grafting on htb_destroy_class_offload when destroying htb
+    - gpio: use raw spinlock for gpio chip shadowed data
+    - gpio: mxc: Protect GPIO irqchip RMW with bgpio spinlock
+    - gpio: mxc: Always set GPIOs used as interrupt source to INPUT mode
+    - pinctrl/rockchip: Use temporary variable for struct device
+    - pinctrl/rockchip: add error handling for pull/drive register getters
+    - pinctrl: rockchip: fix reading pull type on rk3568
+    - net: stmmac: Fix queue statistics reading
+    - net/sched: sch_taprio: fix possible use-after-free
+    - l2tp: Serialize access to sk_user_data with sk_callback_lock
+    - l2tp: Don't sleep and disable BH under writer-side sk_callback_lock
+    - l2tp: convert l2tp_tunnel_list to idr
+    - l2tp: close all race conditions in l2tp_tunnel_register()
+    - octeontx2-pf: Avoid use of GFP_KERNEL in atomic context
+    - net: usb: sr9700: Handle negative len
+    - net: mdio: validate parameter addr in mdiobus_get_phy()
+    - HID: check empty report_list in hid_validate_values()
+    - HID: check empty report_list in bigben_probe()
+    - net: stmmac: fix invalid call to mdiobus_get_phy()
+    - pinctrl: rockchip: fix mux route data for rk3568
+    - HID: revert CHERRY_MOUSE_000C quirk
+    - usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait
+    - usb: gadget: f_fs: Ensure ep0req is dequeued before free_request
+    - Bluetooth: Fix possible deadlock in rfcomm_sk_state_change
+    - net: ipa: disable ipa interrupt during suspend
+    - net/mlx5: E-switch, Fix setting of reserved fields on
+      MODIFY_SCHEDULING_ELEMENT
+    - net: mlx5: eliminate anonymous module_init & module_exit
+    - drm/panfrost: fix GENERIC_ATOMIC64 dependency
+    - dmaengine: Fix double increment of client_count in dma_chan_get()
+    - net: macb: fix PTP TX timestamp failure due to packet padding
+    - virtio-net: correctly enable callback during start_xmit
+    - l2tp: prevent lockdep issue in l2tp_tunnel_register()
+    - HID: betop: check shape of output reports
+    - cifs: fix potential deadlock in cache_refresh_path()
+    - dmaengine: xilinx_dma: call of_node_put() when breaking out of
+      for_each_child_of_node()
+    - phy: phy-can-transceiver: Skip warning if no "max-bitrate"
+    - drm/amd/display: fix issues with driver unload
+    - nvme-pci: fix timeout request state check
+    - tcp: avoid the lookup process failing to get sk in ehash table
+    - octeontx2-pf: Fix the use of GFP_KERNEL in atomic context on rt
+    - ptdma: pt_core_execute_cmd() should use spinlock
+    - device property: fix of node refcount leak in
+      fwnode_graph_get_next_endpoint()
+    - w1: fix deadloop in __w1_remove_master_device()
+    - w1: fix WARNING after calling w1_process()
+    - driver core: Fix test_async_probe_init saves device in wrong array
+    - selftests/net: toeplitz: fix race on tpacket_v3 block close
+    - net: dsa: microchip: ksz9477: port map correction in ALU table entry
+      register
+    - thermal/core: Remove duplicate information when an error occurs
+    - thermal/core: Rename 'trips' to 'num_trips'
+    - thermal: Validate new state in cur_state_store()
+    - thermal/core: fix error code in __thermal_cooling_device_register()
+    - thermal: core: call put_device() only after device_register() fails
+    - net: stmmac: enable all safety features by default
+    - tcp: fix rate_app_limited to default to 1
+    - scsi: iscsi: Fix multiple iSCSI session unbind events sent to userspace
+    - cpufreq: Add Tegra234 to cpufreq-dt-platdev blocklist
+    - kcsan: test: don't put the expect array on the stack
+    - cpufreq: Add SM6375 to cpufreq-dt-platdev blocklist
+    - ASoC: fsl_micfil: Correct the number of steps on SX controls
+    - net: usb: cdc_ether: add support for Thales Cinterion PLS62-W modem
+    - drm: Add orientation quirk for Lenovo ideapad D330-10IGL
+    - s390/debug: add _ASM_S390_ prefix to header guard
+    - s390: expicitly align _edata and _end symbols on page boundary
+    - perf/x86/msr: Add Emerald Rapids
+    - perf/x86/intel/uncore: Add Emerald Rapids
+    - cpufreq: armada-37xx: stop using 0 as NULL pointer
+    - ASoC: fsl_ssi: Rename AC'97 streams to avoid collisions with AC'97 CODEC
+    - ASoC: fsl-asoc-card: Fix naming of AC'97 CODEC widgets
+    - spi: spidev: remove debug messages that access spidev->spi without locking
+    - KVM: s390: interrupt: use READ_ONCE() before cmpxchg()
+    - scsi: hisi_sas: Set a port invalid only if there are no devices attached
+      when refreshing port id
+    - r8152: add vendor/device ID pair for Microsoft Devkit
+    - platform/x86: touchscreen_dmi: Add info for the CSL Panther Tab HD
+    - platform/x86: asus-nb-wmi: Add alternate mapping for KEY_SCREENLOCK
+    - lockref: stop doing cpu_relax in the cmpxchg loop
+    - firmware: coreboot: Check size of table entry and use flex-array
+    - drm/i915: Allow switching away via vga-switcheroo if uninitialized
+    - drm/i915: Remove unused variable
+    - x86: ACPI: cstate: Optimize C3 entry on AMD CPUs
+    - fs: reiserfs: remove useless new_opts in reiserfs_remount
+    - sysctl: add a new register_sysctl_init() interface
+    - kernel/panic: move panic sysctls to its own file
+    - panic: unset panic_on_warn inside panic()
+    - ubsan: no need to unset panic_on_warn in ubsan_epilogue()
+    - kasan: no need to unset panic_on_warn in end_report()
+    - exit: Add and use make_task_dead.
+    - objtool: Add a missing comma to avoid string concatenation
+    - hexagon: Fix function name in die()
+    - h8300: Fix build errors from do_exit() to make_task_dead() transition
+    - csky: Fix function name in csky_alignment() and die()
+    - ia64: make IA64_MCA_RECOVERY bool instead of tristate
+    - panic: Separate sysctl logic from CONFIG_SMP
+    - exit: Put an upper limit on how often we can oops
+    - exit: Expose "oops_count" to sysfs
+    - exit: Allow oops_limit to be disabled
+    - panic: Consolidate open-coded panic_on_warn checks
+    - panic: Introduce warn_limit
+    - panic: Expose "warn_count" to sysfs
+    - docs: Fix path paste-o for /sys/kernel/warn_count
+    - exit: Use READ_ONCE() for all oops/warn limit reads
+    - Bluetooth: hci_sync: cancel cmd_timer if hci_open failed
+    - drm/amdgpu: complete gfxoff allow signal during suspend without delay
+    - scsi: hpsa: Fix allocation size for scsi_host_alloc()
+    - KVM: SVM: fix tsc scaling cache logic
+    - module: Don't wait for GOING modules
+    - tracing: Make sure trace_printk() can output as soon as it can be used
+    - trace_events_hist: add check for return value of 'create_hist_field'
+    - ftrace/scripts: Update the instructions for ftrace-bisect.sh
+    - cifs: Fix oops due to uncleared server->smbd_conn in reconnect
+    - i2c: mv64xxx: Remove shutdown method from driver
+    - i2c: mv64xxx: Add atomic_xfer method to driver
+    - ksmbd: add smbd max io size parameter
+    - ksmbd: add max connections parameter
+    - ksmbd: do not sign response to session request for guest login
+    - ksmbd: downgrade ndr version error message to debug
+    - ksmbd: limit pdu length size according to connection status
+    - ovl: fail on invalid uid/gid mapping at copy up
+    - KVM: x86/vmx: Do not skip segment attributes if unusable bit is set
+    - KVM: arm64: GICv4.1: Fix race with doorbell on VPE activation/deactivation
+    - thermal: intel: int340x: Protect trip temperature from concurrent updates
+    - ipv6: fix reachability confirmation with proxy_ndp
+    - ARM: 9280/1: mm: fix warning on phys_addr_t to void pointer assignment
+    - EDAC/device: Respect any driver-supplied workqueue polling value
+    - EDAC/qcom: Do not pass llcc_driv_data as edac_device_ctl_info's pvt_info
+    - net: mana: Fix IRQ name - add PCI and queue number
+    - scsi: ufs: core: Fix devfreq deadlocks
+    - i2c: designware: use casting of u64 in clock multiplication to avoid
+      overflow
+    - netlink: prevent potential spectre v1 gadgets
+    - net: fix UaF in netns ops registration error path
+    - drm/i915/selftest: fix intel_selftest_modify_policy argument types
+    - netfilter: nft_set_rbtree: Switch to node list walk for overlap detection
+    - netfilter: nft_set_rbtree: skip elements in transaction from garbage
+      collection
+    - netlink: annotate data races around nlk->portid
+    - netlink: annotate data races around dst_portid and dst_group
+    - netlink: annotate data races around sk_state
+    - ipv4: prevent potential spectre v1 gadget in ip_metrics_convert()
+    - ipv4: prevent potential spectre v1 gadget in fib_metrics_match()
+    - netfilter: conntrack: fix vtag checks for ABORT/SHUTDOWN_COMPLETE
+    - netrom: Fix use-after-free of a listening socket.
+    - net/sched: sch_taprio: do not schedule in taprio_reset()
+    - sctp: fail if no bound addresses can be used for a given scope
+    - riscv/kprobe: Fix instruction simulation of JALR
+    - nvme: fix passthrough csi check
+    - gpio: mxc: Unlock on error path in mxc_flip_edge()
+    - ravb: Rename "no_ptp_cfg_active" and "ptp_cfg_active" variables
+    - net: ravb: Fix lack of register setting after system resumed for Gen3
+    - net: ravb: Fix possible hang if RIS2_QFF1 happen
+    - net: mctp: mark socks as dead on unhash, prevent re-add
+    - thermal: intel: int340x: Add locking to int340x_thermal_get_trip_type()
+    - net/tg3: resolve deadlock in tg3_reset_task() during EEH
+    - net: mdio-mux-meson-g12a: force internal PHY off on mux switch
+    - treewide: fix up files incorrectly marked executable
+    - tools: gpio: fix -c option of gpio-event-mon
+    - Revert "Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI
+      mode"
+    - cpufreq: Move to_gov_attr_set() to cpufreq.h
+    - cpufreq: governor: Use kobject release() method to free dbs_data
+    - kbuild: Allow kernel installation packaging to override pkg-config
+    - block: fix and cleanup bio_check_ro
+    - x86/i8259: Mark legacy PIC interrupts with IRQ_LEVEL
+    - netfilter: conntrack: unify established states for SCTP paths
+    - perf/x86/amd: fix potential integer overflow on shift of a int
+    - Linux 5.15.91
+
+  * Kernel livepatch support for for s390x (LP: #1639924)
+    - sched: Improve try_invoke_on_locked_down_task()
+    - sched,rcu: Rework try_invoke_on_locked_down_task()
+    - sched,livepatch: Use task_call_func()
+    - sched: Simplify wake_up_*idle*()
+    - sched,livepatch: Use wake_up_if_idle()
+    - sched: Improve wake_up_all_idle_cpus() take #2
+    - s390/entry: remove unused expoline thunk
+    - s390: remove unused expoline to BC instructions
+    - s390/nospec: generate single register thunks if possible
+    - s390/nospec: add an option to use thunk-extern
+    - s390/nospec: align and size extern thunks
+    - bug: Use normal relative pointers in 'struct bug_entry'
+    - s390/nospec: build expoline.o for modules_prepare target
+    - [Config] Enable EXPOLINE_EXTERN on s390x
+    - [Config] s390x: Removing UBSAN from configuration
+
+  * Do not sort the task scan result from /proc when synthesizing perf events
+    (LP: #2008971)
+    - perf synthetic-events: Don't sort the task scan result from /proc
+
+  * linux: Staging modules should be unsigned (LP: #1642368)
+    - [Packaging] Move and update signature inclusion list
+    - SAUCE: Add selective signing of staging modules
+    - [Packaging] Add module-signature-check
+    - [Packaging] module-signature-check: Check debian.<foo>/signature-inclusion
+    - [Packaging] Introduce debian/scripts/sign-module
+    - SAUCE: Switch to using debian/scripts/sign-module
+
+  * Jammy update: v5.15.90 upstream stable release (LP: #2008933)
+    - btrfs: fix trace event name typo for FLUSH_DELAYED_REFS
+    - pNFS/filelayout: Fix coalescing test for single DS
+    - tools/virtio: initialize spinlocks in vring_test.c
+    - virtio_pci: modify ENOENT to EINVAL
+    - vduse: Validate vq_num in vduse_validate_config()
+    - net/ethtool/ioctl: return -EOPNOTSUPP if we have no phy stats
+    - r8169: move rtl_wol_enable_rx() and rtl_prepare_power_down()
+    - RDMA/srp: Move large values to a new enum for gcc13
+    - btrfs: always report error in run_one_delayed_ref()
+    - x86/asm: Fix an assembler warning with current binutils
+    - f2fs: let's avoid panic if extent_tree is not created
+    - perf/x86/rapl: Treat Tigerlake like Icelake
+    - fbdev: omapfb: avoid stack overflow warning
+    - Bluetooth: hci_qca: Fix driver shutdown on closed serdev
+    - wifi: brcmfmac: fix regression for Broadcom PCIe wifi devices
+    - wifi: mac80211: sdata can be NULL during AMPDU start
+    - Add exception protection processing for vd in axi_chan_handle_err function
+    - zonefs: Detect append writes at invalid locations
+    - nilfs2: fix general protection fault in nilfs_btree_insert()
+    - efi: fix userspace infinite retry read efivars after EFI runtime services
+      page fault
+    - ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
+    - ALSA: hda/realtek: fix mute/micmute LEDs don't work for a HP platform
+    - drm/amdgpu: disable runtime pm on several sienna cichlid cards(v2)
+    - drm/amd: Delay removal of the firmware framebuffer
+    - hugetlb: unshare some PMDs when splitting VMAs
+    - io_uring: don't gate task_work run on TIF_NOTIFY_SIGNAL
+    - eventpoll: add EPOLL_URING_WAKE poll wakeup flag
+    - eventfd: provide a eventfd_signal_mask() helper
+    - io_uring: pass in EPOLL_URING_WAKE for eventfd signaling and wakeups
+    - io_uring: improve send/recv error handling
+    - io_uring: ensure recv and recvmsg handle MSG_WAITALL correctly
+    - io_uring: add flag for disabling provided buffer recycling
+    - io_uring: support MSG_WAITALL for IORING_OP_SEND(MSG)
+    - io_uring: allow re-poll if we made progress
+    - io_uring: fix async accept on O_NONBLOCK sockets
+    - io_uring: ensure that cached task references are always put on exit
+    - io_uring: remove duplicated calls to io_kiocb_ppos
+    - io_uring: update kiocb->ki_pos at execution time
+    - io_uring: do not recalculate ppos unnecessarily
+    - io_uring/rw: defer fsnotify calls to task context
+    - xhci-pci: set the dma max_seg_size
+    - usb: xhci: Check endpoint is valid before dereferencing it
+    - xhci: Fix null pointer dereference when host dies
+    - xhci: Add update_hub_device override for PCI xHCI hosts
+    - xhci: Add a flag to disable USB3 lpm on a xhci root port level.
+    - usb: acpi: add helper to check port lpm capability using acpi _DSM
+    - xhci: Detect lpm incapable xHC USB3 roothub ports from ACPI tables
+    - prlimit: do_prlimit needs to have a speculation check
+    - USB: serial: option: add Quectel EM05-G (GR) modem
+    - USB: serial: option: add Quectel EM05-G (CS) modem
+    - USB: serial: option: add Quectel EM05-G (RS) modem
+    - USB: serial: option: add Quectel EC200U modem
+    - USB: serial: option: add Quectel EM05CN (SG) modem
+    - USB: serial: option: add Quectel EM05CN modem
+    - staging: vchiq_arm: fix enum vchiq_status return types
+    - USB: misc: iowarrior: fix up header size for USB_DEVICE_ID_CODEMERCS_IOW100
+    - misc: fastrpc: Don't remove map on creater_process and device_release
+    - misc: fastrpc: Fix use-after-free race condition for maps
+    - usb: core: hub: disable autosuspend for TI TUSB8041
+    - comedi: adv_pci1760: Fix PWM instruction handling
+    - ACPI: PRM: Check whether EFI runtime is available
+    - mmc: sunxi-mmc: Fix clock refcount imbalance during unbind
+    - mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting
+    - btrfs: do not abort transaction on failure to write log tree when syncing
+      log
+    - btrfs: fix race between quota rescan and disable leading to NULL pointer
+      deref
+    - cifs: do not include page data when checking signature
+    - thunderbolt: Use correct function to calculate maximum USB3 link rate
+    - riscv: dts: sifive: fu740: fix size of pcie 32bit memory
+    - bpf: restore the ebpf program ID for BPF_AUDIT_UNLOAD and
+      PERF_BPF_EVENT_PROG_UNLOAD
+    - staging: mt7621-dts: change some node hex addresses to lower case
+    - tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
+    - tty: fix possible null-ptr-defer in spk_ttyio_release
+    - USB: serial: cp210x: add SCALANCE LPE-9000 device id
+    - usb: cdns3: remove fetched trb from cache before dequeuing
+    - usb: host: ehci-fsl: Fix module alias
+    - usb: typec: tcpm: Fix altmode re-registration causes sysfs create fail
+    - usb: typec: altmodes/displayport: Add pin assignment helper
+    - usb: typec: altmodes/displayport: Fix pin assignment calculation
+    - usb: gadget: g_webcam: Send color matching descriptor per frame
+    - usb: gadget: f_ncm: fix potential NULL ptr deref in ncm_bitrate()
+    - usb-storage: apply IGNORE_UAS only for HIKSEMI MD202 on RTL9210
+    - dt-bindings: phy: g12a-usb2-phy: fix compatible string documentation
+    - dt-bindings: phy: g12a-usb3-pcie-phy: fix compatible string documentation
+    - serial: pch_uart: Pass correct sg to dma_unmap_sg()
+    - dmaengine: lgm: Move DT parsing after initialization
+    - dmaengine: tegra210-adma: fix global intr clear
+    - dmaengine: idxd: Let probe fail when workqueue cannot be enabled
+    - serial: amba-pl011: fix high priority character transmission in rs486 mode
+    - serial: atmel: fix incorrect baudrate setup
+    - gsmi: fix null-deref in gsmi_get_variable
+    - mei: me: add meteor lake point M DID
+    - drm/i915: re-disable RC6p on Sandy Bridge
+    - drm/i915/display: Check source height is > 0
+    - drm/amd/display: Fix set scaling doesn's work
+    - drm/amd/display: Calculate output_color_space after pixel encoding
+      adjustment
+    - drm/amd/display: Fix COLOR_SPACE_YCBCR2020_TYPE matrix
+    - drm/amdgpu: drop experimental flag on aldebaran
+    - fs/ntfs3: Fix attr_punch_hole() null pointer derenference
+    - arm64: efi: Execute runtime services from a dedicated stack
+    - efi: rt-wrapper: Add missing include
+    - x86/fpu: Use _Alignof to avoid undefined behavior in TYPE_ALIGN
+    - tracing: Use alignof__(struct {type b;}) instead of offsetof()
+    - io_uring: io_kiocb_update_pos() should not touch file for non -1 offset
+    - io_uring/net: fix fast_iov assignment in io_setup_async_msg()
+    - net/mlx5: fix missing mutex_unlock in mlx5_fw_fatal_reporter_err_work()
+    - block: mq-deadline: Rename deadline_is_seq_writes()
+    - soc: qcom: apr: Make qcom,protection-domain optional again
+    - mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
+    - io_uring: Clean up a false-positive warning from GCC 9.3.0
+    - io_uring: fix double poll leak on repolling
+    - io_uring/rw: ensure kiocb_end_write() is always called
+    - io_uring/rw: remove leftover debug statement
+    - Linux 5.15.90
+
+  * Jammy update: v5.15.89 upstream stable release (LP: #2008929)
+    - ALSA: control-led: use strscpy in set_led_id()
+    - ALSA: hda/realtek - Turn on power early
+    - ALSA: hda/realtek: Enable mute/micmute LEDs on HP Spectre x360 13-aw0xxx
+    - KVM: arm64: Fix S1PTW handling on RO memslots
+    - KVM: arm64: nvhe: Fix build with profile optimization
+    - selftests: kvm: Fix a compile error in selftests/kvm/rseq_test.c
+    - efi: tpm: Avoid READ_ONCE() for accessing the event log
+    - docs: Fix the docs build with Sphinx 6.0
+    - net: stmmac: add aux timestamps fifo clearance wait
+    - perf auxtrace: Fix address filter duplicate symbol selection
+    - s390/kexec: fix ipl report address for kdump
+    - ASoC: qcom: lpass-cpu: Fix fallback SD line index handling
+    - s390/cpum_sf: add READ_ONCE() semantics to compare and swap loops
+    - s390/percpu: add READ_ONCE() to arch_this_cpu_to_op_simple()
+    - drm/virtio: Fix GEM handle creation UAF
+    - drm/i915/gt: Reset twice
+    - net/mlx5e: Set action fwd flag when parsing tc action goto
+    - cifs: Fix uninitialized memory read for smb311 posix symlink create
+    - platform/x86: dell-privacy: Only register SW_CAMERA_LENS_COVER if present
+    - platform/surface: aggregator: Ignore command messages not intended for us
+    - platform/x86: dell-privacy: Fix SW_CAMERA_LENS_COVER reporting
+    - dt-bindings: msm: dsi-controller-main: Fix operating-points-v2 constraint
+    - drm/msm/adreno: Make adreno quirks not overwrite each other
+    - dt-bindings: msm: dsi-controller-main: Fix power-domain constraint
+    - dt-bindings: msm: dsi-controller-main: Fix description of core clock
+    - dt-bindings: msm: dsi-phy-28nm: Add missing qcom, dsi-phy-regulator-ldo-mode
+    - platform/x86: ideapad-laptop: Add Legion 5 15ARH05 DMI id to
+      set_fn_lock_led_list[]
+    - drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux
+      transfer
+    - dt-bindings: msm/dsi: Don't require vdds-supply on 10nm PHY
+    - dt-bindings: msm/dsi: Don't require vcca-supply on 14nm PHY
+    - platform/x86: sony-laptop: Don't turn off 0x153 keyboard backlight during
+      probe
+    - ixgbe: fix pci device refcount leak
+    - ipv6: raw: Deduct extension header length in rawv6_push_pending_frames
+    - bus: mhi: host: Fix race between channel preparation and M0 event
+    - usb: ulpi: defer ulpi_register on ulpi_read_id timeout
+    - iommu/iova: Fix alloc iova overflows issue
+    - iommu/mediatek-v1: Fix an error handling path in mtk_iommu_v1_probe()
+    - sched/core: Fix use-after-free bug in dup_user_cpus_ptr()
+    - netfilter: ipset: Fix overflow before widen in the bitmap_ip_create()
+      function.
+    - powerpc/imc-pmu: Fix use of mutex in IRQs disabled section
+    - x86/boot: Avoid using Intel mnemonics in AT&T syntax asm
+    - EDAC/device: Fix period calculation in edac_device_reset_delay_period()
+    - x86/resctrl: Fix task CLOSID/RMID update race
+    - regulator: da9211: Use irq handler when ready
+    - scsi: mpi3mr: Refer CONFIG_SCSI_MPI3MR in Makefile
+    - scsi: ufs: Stop using the clock scaling lock in the error handler
+    - scsi: ufs: core: WLUN suspend SSU/enter hibern8 fail recovery
+    - ASoC: wm8904: fix wrong outputs volume after power reactivation
+    - ALSA: usb-audio: Make sure to stop endpoints before closing EPs
+    - ALSA: usb-audio: Relax hw constraints for implicit fb sync
+    - tipc: fix unexpected link reset due to discovery messages
+    - octeontx2-af: Fix LMAC config in cgx_lmac_rx_tx_enable
+    - hvc/xen: lock console list traversal
+    - nfc: pn533: Wait for out_urb's completion in pn533_usb_send_frame()
+    - af_unix: selftest: Fix the size of the parameter to connect()
+    - tools/nolibc: x86: Remove `r8`, `r9` and `r10` from the clobber list
+    - tools/nolibc: x86-64: Use `mov $60,%eax` instead of `mov $60,%rax`
+    - tools/nolibc: use pselect6 on RISCV
+    - tools/nolibc/std: move the standard type definitions to std.h
+    - tools/nolibc/types: split syscall-specific definitions into their own files
+    - tools/nolibc/arch: split arch-specific code into individual files
+    - tools/nolibc/arch: mark the _start symbol as weak
+    - tools/nolibc: Remove .global _start from the entry point code
+    - tools/nolibc: restore mips branch ordering in the _start block
+    - tools/nolibc: fix the O_* fcntl/open macro definitions for riscv
+    - net/sched: act_mpls: Fix warning during failed attribute validation
+    - net/mlx5: Fix ptp max frequency adjustment range
+    - net/mlx5e: Don't support encap rules with gbp option
+    - perf build: Properly guard libbpf includes
+    - igc: Fix PPS delta between two synchronized end-points
+    - platform/surface: aggregator: Add missing call to ssam_request_sync_free()
+    - Documentation: KVM: add API issues section
+    - KVM: x86: Do not return host topology information from
+      KVM_GET_SUPPORTED_CPUID
+    - io_uring: lock overflowing for IOPOLL
+    - arm64: atomics: format whitespace consistently
+    - arm64: atomics: remove LL/SC trampolines
+    - arm64: cmpxchg_double*: hazard against entire exchange variable
+    - efi: fix NULL-deref in init error path
+    - io_uring/io-wq: free worker if task_work creation is canceled
+    - io_uring/io-wq: only free worker if it was allocated for creation
+    - block: handle bio_split_to_limits() NULL return
+    - Revert "usb: ulpi: defer ulpi_register on ulpi_read_id timeout"
+    - pinctrl: amd: Add dynamic debugging for active GPIOs
+    - Linux 5.15.89
+
+  * Jammy update: v5.15.88 upstream stable release (LP: #2008927)
+    - parisc: Align parisc MADV_XXX constants with all other architectures
+    - serial: fixup backport of "serial: Deassert Transmit Enable on probe in
+      driver-specific way"
+    - net: sched: disallow noqueue for qdisc classes
+    - ALSA: hda/hdmi: Add a HP device 0x8715 to force connect list
+    - ALSA: hda - Enable headset mic on another Dell laptop with ALC3254
+    - Linux 5.15.88
+
+  * Fix selftests/ftracetests/Meta-selftests (LP: #2006453)
+    - selftests/ftrace: Fix bash specific "==" operator
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 21 Mar 2023 10:08:08 +0100
+
+linux (5.15.0-69.76) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-69.76 -proposed tracker (LP: #2012092)
+
+  * NFS deathlock with last Kernel 5.4.0-144.161 and 5.15.0-67.74 (LP: #2009325)
+    - NFS: Correct timing for assigning access cache timestamp
+
+ -- Kleber Sacilotto de Souza <kleber.souza@canonical.com>  Fri, 17 Mar 2023 17:56:55 +0100
+
+linux (5.15.0-68.75) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-68.75 -proposed tracker (LP: #2008349)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2023.02.27)
+
+  * Ubuntu 22.04 kernel 5.15.0-46-generic leaks kernel memory in kmalloc-2k
+    slabs (LP: #1987430)
+    - SAUCE: audit: fix memory leak of audit_log_lsm()
+
+  * [EGS] Backport intel_idle support for Eagle Stream Ubuntu 22.04 release
+    (LP: #2003267)
+    - intel_idle: add SPR support
+    - intel_idle: add 'preferred_cstates' module argument
+    - intel_idle: add core C6 optimization for SPR
+    - cpuidle: intel_idle: Drop redundant backslash at line end
+    - intel_idle: Fix the 'preferred_cstates' module parameter
+    - intel_idle: Fix SPR C6 optimization
+    - intel_idle: make SPR C1 and C1E be independent
+
+  * Fix speaker mute hotkey doesn't work on Dell G16 series (LP: #2003161)
+    - platform/x86: dell-wmi: Add a keymap for KEY_MUTE in type 0x0010 table
+
+  * Fix the ACPI _CPC not found error from kernel dmesg on some dynamic SSDT
+    table loaded firmwares (LP: #2006077)
+    - ACPI: bus: Avoid using CPPC if not supported by firmware
+    - ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
+    - ACPI: CPPC: Only probe for _CPC if CPPC v2 is acked
+
+  * rtcpie in timers from ubuntu_kernel_selftests randomly failing
+    (LP: #1814234)
+    - SAUCE: selftest: rtcpie: Force passing unreliable subtest
+
+  * Jammy update: v5.15.87 upstream stable release (LP: #2007441)
+    - usb: dwc3: qcom: Fix memory leak in dwc3_qcom_interconnect_init
+    - cifs: fix oops during encryption
+    - nvme-pci: fix doorbell buffer value endianness
+    - nvme-pci: fix mempool alloc size
+    - nvme-pci: fix page size checks
+    - ACPI: resource: do IRQ override on LENOVO IdeaPad
+    - ACPI: resource: do IRQ override on XMG Core 15
+    - ACPI: resource: do IRQ override on Lenovo 14ALC7
+    - block, bfq: fix uaf for bfqq in bfq_exit_icq_bfqq
+    - ata: ahci: Fix PCS quirk application for suspend
+    - nvme: fix the NVME_CMD_EFFECTS_CSE_MASK definition
+    - nvmet: don't defer passthrough commands with trivial effects to the
+      workqueue
+    - fs/ntfs3: Validate BOOT record_size
+    - fs/ntfs3: Add overflow check for attribute size
+    - fs/ntfs3: Validate data run offset
+    - fs/ntfs3: Add null pointer check to attr_load_runs_vcn
+    - fs/ntfs3: Fix memory leak on ntfs_fill_super() error path
+    - fs/ntfs3: Add null pointer check for inode operations
+    - fs/ntfs3: Validate attribute name offset
+    - fs/ntfs3: Validate buffer length while parsing index
+    - fs/ntfs3: Validate resident attribute name
+    - fs/ntfs3: Fix slab-out-of-bounds read in run_unpack
+    - soundwire: dmi-quirks: add quirk variant for LAPBC710 NUC15
+    - fs/ntfs3: Validate index root when initialize NTFS security
+    - fs/ntfs3: Use __GFP_NOWARN allocation at wnd_init()
+    - fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_fill_super()
+    - fs/ntfs3: Delete duplicate condition in ntfs_read_mft()
+    - fs/ntfs3: Fix slab-out-of-bounds in r_page
+    - objtool: Fix SEGFAULT
+    - powerpc/rtas: avoid device tree lookups in rtas_os_term()
+    - powerpc/rtas: avoid scheduling in rtas_os_term()
+    - HID: multitouch: fix Asus ExpertBook P2 P2451FA trackpoint
+    - HID: plantronics: Additional PIDs for double volume key presses quirk
+    - pstore: Properly assign mem_type property
+    - pstore/zone: Use GFP_ATOMIC to allocate zone buffer
+    - hfsplus: fix bug causing custom uid and gid being unable to be assigned with
+      mount
+    - binfmt: Fix error return code in load_elf_fdpic_binary()
+    - ovl: Use ovl mounter's fsuid and fsgid in ovl_link()
+    - ALSA: line6: correct midi status byte when receiving data from podxt
+    - ALSA: line6: fix stack overflow in line6_midi_transmit
+    - pnode: terminate at peers of source
+    - mfd: mt6360: Add bounds checking in Regmap read/write call-backs
+    - md: fix a crash in mempool_free
+    - mm, compaction: fix fast_isolate_around() to stay within boundaries
+    - f2fs: should put a page when checking the summary info
+    - f2fs: allow to read node block after shutdown
+    - mmc: vub300: fix warning - do not call blocking ops when !TASK_RUNNING
+    - tpm: acpi: Call acpi_put_table() to fix memory leak
+    - tpm: tpm_crb: Add the missed acpi_put_table() to fix memory leak
+    - tpm: tpm_tis: Add the missed acpi_put_table() to fix memory leak
+    - SUNRPC: Don't leak netobj memory when gss_read_proxy_verf() fails
+    - kcsan: Instrument memcpy/memset/memmove with newer Clang
+    - ASoC: Intel/SOF: use set_stream() instead of set_tdm_slots() for HDAudio
+    - ASoC/SoundWire: dai: expand 'stream' concept beyond SoundWire
+    - rcu-tasks: Simplify trc_read_check_handler() atomic operations
+    - net/af_packet: add VLAN support for AF_PACKET SOCK_RAW GSO
+    - net/af_packet: make sure to pull mac header
+    - media: stv0288: use explicitly signed char
+    - soc: qcom: Select REMAP_MMIO for LLCC driver
+    - kest.pl: Fix grub2 menu handling for rebooting
+    - ktest.pl minconfig: Unset configs instead of just removing them
+    - jbd2: use the correct print format
+    - perf/x86/intel/uncore: Disable I/O stacks to PMU mapping on ICX-D
+    - perf/x86/intel/uncore: Clear attr_update properly
+    - arm64: dts: qcom: sdm845-db845c: correct SPI2 pins drive strength
+    - mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K
+    - btrfs: fix resolving backrefs for inline extent followed by prealloc
+    - ARM: ux500: do not directly dereference __iomem
+    - arm64: dts: qcom: sdm850-lenovo-yoga-c630: correct I2C12 pins drive strength
+    - selftests: Use optional USERCFLAGS and USERLDFLAGS
+    - PM/devfreq: governor: Add a private governor_data for governor
+    - cpufreq: Init completion before kobject_init_and_add()
+    - ALSA: patch_realtek: Fix Dell Inspiron Plus 16
+    - ALSA: hda/realtek: Apply dual codec fixup for Dell Latitude laptops
+    - fs: dlm: fix sock release if listen fails
+    - fs: dlm: retry accept() until -EAGAIN or error returns
+    - mptcp: mark ops structures as ro_after_init
+    - mptcp: remove MPTCP 'ifdef' in TCP SYN cookies
+    - dm cache: Fix ABBA deadlock between shrink_slab and dm_cache_metadata_abort
+    - dm thin: Fix ABBA deadlock between shrink_slab and dm_pool_abort_metadata
+    - dm thin: Use last transaction's pmd->root when commit failed
+    - dm thin: resume even if in FAIL mode
+    - dm thin: Fix UAF in run_timer_softirq()
+    - dm integrity: Fix UAF in dm_integrity_dtr()
+    - dm clone: Fix UAF in clone_dtr()
+    - dm cache: Fix UAF in destroy()
+    - dm cache: set needs_check flag after aborting metadata
+    - tracing/hist: Fix out-of-bound write on 'action_data.var_ref_idx'
+    - perf/core: Call LSM hook after copying perf_event_attr
+    - of/kexec: Fix reading 32-bit "linux,initrd-{start,end}" values
+    - KVM: VMX: Resume guest immediately when injecting #GP on ECREATE
+    - KVM: nVMX: Inject #GP, not #UD, if "generic" VMXON CR0/CR4 check fails
+    - KVM: nVMX: Properly expose ENABLE_USR_WAIT_PAUSE control to L1
+    - x86/microcode/intel: Do not retry microcode reloading on the APs
+    - ftrace/x86: Add back ftrace_expected for ftrace bug reports
+    - x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
+    - x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
+    - tracing: Fix race where eprobes can be called before the event
+    - tracing: Fix complicated dependency of CONFIG_TRACER_MAX_TRACE
+    - tracing/hist: Fix wrong return value in parse_action_params()
+    - tracing/probes: Handle system names with hyphens
+    - tracing: Fix infinite loop in tracing_read_pipe on overflowed
+      print_trace_line
+    - staging: media: tegra-video: fix chan->mipi value on error
+    - staging: media: tegra-video: fix device_node use after free
+    - ARM: 9256/1: NWFPE: avoid compiler-generated __aeabi_uldivmod
+    - media: dvb-core: Fix double free in dvb_register_device()
+    - cifs: fix confusing debug message
+    - cifs: fix missing display of three mount options
+    - rtc: ds1347: fix value written to century register
+    - block: mq-deadline: Do not break sequential write streams to zoned HDDs
+    - md/bitmap: Fix bitmap chunk size overflow issues
+    - efi: Add iMac Pro 2017 to uefi skip cert quirk
+    - wifi: wilc1000: sdio: fix module autoloading
+    - ASoC: jz4740-i2s: Handle independent FIFO flush bits
+    - ipu3-imgu: Fix NULL pointer dereference in imgu_subdev_set_selection()
+    - ipmi: fix long wait in unload when IPMI disconnect
+    - mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
+    - ima: Fix a potential NULL pointer access in ima_restore_measurement_list
+    - ipmi: fix use after free in _ipmi_destroy_user()
+    - PCI: Fix pci_device_is_present() for VFs by checking PF
+    - PCI/sysfs: Fix double free in error path
+    - riscv: stacktrace: Fixup ftrace_graph_ret_addr retp argument
+    - riscv: mm: notify remote harts about mmu cache updates
+    - crypto: n2 - add missing hash statesize
+    - driver core: Fix bus_type.match() error handling in __driver_attach()
+    - phy: qcom-qmp-combo: fix sc8180x reset
+    - iommu/amd: Fix ivrs_acpihid cmdline parsing code
+    - remoteproc: core: Do pm_relax when in RPROC_OFFLINE state
+    - parisc: led: Fix potential null-ptr-deref in start_task()
+    - device_cgroup: Roll back to original exceptions after copy failure
+    - drm/connector: send hotplug uevent on connector cleanup
+    - drm/vmwgfx: Validate the box size for the snooped cursor
+    - drm/i915/dsi: fix VBT send packet port selection for dual link DSI
+    - drm/ingenic: Fix missing platform_driver_unregister() call in
+      ingenic_drm_init()
+    - ext4: silence the warning when evicting inode with dioread_nolock
+    - ext4: add inode table check in __ext4_get_inode_loc to aovid possible
+      infinite loop
+    - ext4: remove trailing newline from ext4_msg() message
+    - fs: ext4: initialize fsdata in pagecache_write()
+    - ext4: fix use-after-free in ext4_orphan_cleanup
+    - ext4: fix undefined behavior in bit shift for ext4_check_flag_values
+    - ext4: add EXT4_IGET_BAD flag to prevent unexpected bad inode
+    - ext4: add helper to check quota inums
+    - ext4: fix bug_on in __es_tree_search caused by bad quota inode
+    - ext4: fix reserved cluster accounting in __es_remove_extent()
+    - ext4: check and assert if marking an no_delete evicting inode dirty
+    - ext4: fix bug_on in __es_tree_search caused by bad boot loader inode
+    - ext4: fix leaking uninitialized memory in fast-commit journal
+    - ext4: fix uninititialized value in 'ext4_evict_inode'
+    - ext4: init quota for 'old.inode' in 'ext4_rename'
+    - ext4: fix delayed allocation bug in ext4_clu_mapped for bigalloc + inline
+    - ext4: fix error code return to user-space in ext4_get_branch()
+    - ext4: avoid BUG_ON when creating xattrs
+    - ext4: fix kernel BUG in 'ext4_write_inline_data_end()'
+    - ext4: fix inode leak in ext4_xattr_inode_create() on an error path
+    - ext4: initialize quota before expanding inode in setproject ioctl
+    - ext4: avoid unaccounted block allocation when expanding inode
+    - ext4: allocate extended attribute value in vmalloc area
+    - drm/amdgpu: handle polaris10/11 overlap asics (v2)
+    - block: mq-deadline: Fix dd_finish_request() for zoned devices
+    - tracing: Fix issue of missing one synthetic field
+    - ext4: remove unused enum EXT4_FC_COMMIT_FAILED
+    - ext4: use ext4_debug() instead of jbd_debug()
+    - ext4: introduce EXT4_FC_TAG_BASE_LEN helper
+    - ext4: factor out ext4_fc_get_tl()
+    - ext4: fix potential out of bound read in ext4_fc_replay_scan()
+    - ext4: disable fast-commit of encrypted dir operations
+    - ext4: don't set up encryption key during jbd2 transaction
+    - ext4: add missing validation of fast-commit record lengths
+    - ext4: fix unaligned memory access in ext4_fc_reserve_space()
+    - ext4: fix off-by-one errors in fast-commit block filling
+    - ARM: renumber bits related to _TIF_WORK_MASK
+    - phy: qcom-qmp-combo: fix out-of-bounds clock access
+    - btrfs: replace strncpy() with strscpy()
+    - btrfs: move missing device handling in a dedicate function
+    - btrfs: fix extent map use-after-free when handling missing device in
+      read_one_chunk
+    - x86/mce: Get rid of msr_ops
+    - x86/MCE/AMD: Clear DFR errors found in THR handler
+    - media: s5p-mfc: Fix to handle reference queue during finishing
+    - media: s5p-mfc: Clear workbit to handle error condition
+    - media: s5p-mfc: Fix in register read and write for H264
+    - perf probe: Use dwarf_attr_integrate as generic DWARF attr accessor
+    - perf probe: Fix to get the DW_AT_decl_file and DW_AT_call_file as unsinged
+      data
+    - ravb: Fix "failed to switch device to config mode" message during unbind
+    - ext4: goto right label 'failed_mount3a'
+    - ext4: correct inconsistent error msg in nojournal mode
+    - mbcache: automatically delete entries from cache on freeing
+    - ext4: fix deadlock due to mbcache entry corruption
+    - drm/i915/migrate: don't check the scratch page
+    - drm/i915/migrate: fix offset calculation
+    - drm/i915/migrate: fix length calculation
+    - SUNRPC: ensure the matching upcall is in-flight upon downcall
+    - btrfs: fix an error handling path in btrfs_defrag_leaves()
+    - bpf: pull before calling skb_postpull_rcsum()
+    - drm/panfrost: Fix GEM handle creation ref-counting
+    - netfilter: nf_tables: consolidate set description
+    - netfilter: nf_tables: add function to create set stateful expressions
+    - netfilter: nf_tables: perform type checking for existing sets
+    - vmxnet3: correctly report csum_level for encapsulated packet
+    - netfilter: nf_tables: honor set timeout and garbage collection updates
+    - veth: Fix race with AF_XDP exposing old or uninitialized descriptors
+    - nfsd: shut down the NFSv4 state objects before the filecache
+    - net: hns3: add interrupts re-initialization while doing VF FLR
+    - net: hns3: refactor hns3_nic_reuse_page()
+    - net: hns3: extract macro to simplify ring stats update code
+    - net: hns3: fix miss L3E checking for rx packet
+    - net: hns3: fix VF promisc mode not update when mac table full
+    - net: sched: fix memory leak in tcindex_set_parms
+    - qlcnic: prevent ->dcb use-after-free on qlcnic_dcb_enable() failure
+    - net: dsa: mv88e6xxx: depend on PTP conditionally
+    - nfc: Fix potential resource leaks
+    - vdpa_sim: fix possible memory leak in vdpasim_net_init() and
+      vdpasim_blk_init()
+    - vhost/vsock: Fix error handling in vhost_vsock_init()
+    - vringh: fix range used in iotlb_translate()
+    - vhost: fix range used in translate_desc()
+    - vdpa_sim: fix vringh initialization in vdpasim_queue_ready()
+    - net/mlx5: E-Switch, properly handle ingress tagged packets on VST
+    - net/mlx5: Add forgotten cleanup calls into mlx5_init_once() error path
+    - net/mlx5: Avoid recovery in probe flows
+    - net/mlx5e: IPoIB, Don't allow CQE compression to be turned on by default
+    - net/mlx5e: TC, Refactor mlx5e_tc_add_flow_mod_hdr() to get flow attr
+    - net/mlx5e: Always clear dest encap in neigh-update-del
+    - net/mlx5e: Fix hw mtu initializing at XDP SQ allocation
+    - net: amd-xgbe: add missed tasklet_kill
+    - net: ena: Fix toeplitz initial hash value
+    - net: ena: Don't register memory info on XDP exchange
+    - net: ena: Account for the number of processed bytes in XDP
+    - net: ena: Use bitmask to indicate packet redirection
+    - net: ena: Fix rx_copybreak value update
+    - net: ena: Set default value for RX interrupt moderation
+    - net: ena: Update NUMA TPH hint register upon NUMA node update
+    - net: phy: xgmiitorgmii: Fix refcount leak in xgmiitorgmii_probe
+    - RDMA/mlx5: Fix mlx5_ib_get_hw_stats when used for device
+    - RDMA/mlx5: Fix validation of max_rd_atomic caps for DC
+    - drm/meson: Reduce the FIFO lines held when AFBC is not used
+    - filelock: new helper: vfs_inode_has_locks
+    - ceph: switch to vfs_inode_has_locks() to fix file lock bug
+    - gpio: sifive: Fix refcount leak in sifive_gpio_probe
+    - net: sched: atm: dont intepret cls results when asked to drop
+    - net: sched: cbq: dont intepret cls results when asked to drop
+    - net: sparx5: Fix reading of the MAC address
+    - netfilter: ipset: fix hash:net,port,net hang with /0 subnet
+    - netfilter: ipset: Rework long task execution when adding/deleting entries
+    - perf tools: Fix resources leak in perf_data__open_dir()
+    - drm/imx: ipuv3-plane: Fix overlay plane width
+    - fs/ntfs3: don't hold ni_lock when calling truncate_setsize()
+    - drivers/net/bonding/bond_3ad: return when there's no aggregator
+    - octeontx2-pf: Fix lmtst ID used in aura free
+    - usb: rndis_host: Secure rndis_query check against int overflow
+    - perf stat: Fix handling of --for-each-cgroup with --bpf-counters to match
+      non BPF mode
+    - drm/i915: unpin on error in intel_vgpu_shadow_mm_pin()
+    - caif: fix memory leak in cfctrl_linkup_request()
+    - udf: Fix extension of the last extent in the file
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
+    - nvme: fix multipath crash caused by flush request when blktrace is enabled
+    - io_uring: check for valid register opcode earlier
+    - nvmet: use NVME_CMD_EFFECTS_CSUPP instead of open coding it
+    - nvme: also return I/O command effects from nvme_command_effects
+    - btrfs: check superblock to ensure the fs was not modified at thaw time
+    - x86/kexec: Fix double-free of elf header buffer
+    - nfsd: fix handling of readdir in v4root vs. mount upcall timeout
+    - fbdev: matroxfb: G200eW: Increase max memory from 1 MB to 16 MB
+    - block: don't allow splitting of a REQ_NOWAIT bio
+    - io_uring: fix CQ waiting timeout handling
+    - thermal: int340x: Add missing attribute for data rate base
+    - riscv: uaccess: fix type of 0 variable on error in get_user()
+    - riscv, kprobes: Stricter c.jr/c.jalr decoding
+    - drm/i915/gvt: fix gvt debugfs destroy
+    - drm/i915/gvt: fix vgpu debugfs clean in remove
+    - hfs/hfsplus: use WARN_ON for sanity check
+    - hfs/hfsplus: avoid WARN_ON() for sanity check, use proper error handling
+    - ksmbd: fix infinite loop in ksmbd_conn_handler_loop()
+    - ksmbd: check nt_len to be at least CIFS_ENCPWD_SIZE in
+      ksmbd_decode_ntlmssp_auth_blob
+    - Revert "ACPI: PM: Add support for upcoming AMD uPEP HID AMDI007"
+    - mptcp: dedicated request sock for subflow in v6
+    - mptcp: use proper req destructor for IPv6
+    - ext4: don't allow journal inode to have encrypt flag
+    - selftests: set the BUILD variable to absolute path
+    - btrfs: make thaw time super block check to also verify checksum
+    - net: hns3: fix return value check bug of rx copybreak
+    - mbcache: Avoid nesting of cache->c_list_lock under bit locks
+    - efi: random: combine bootloader provided RNG seed with RNG protocol output
+    - io_uring: Fix unsigned 'res' comparison with zero in io_fixup_rw_res()
+    - drm/mgag200: Fix PLL setup for G200_SE_A rev >=4
+    - Linux 5.15.87
+
+  * Jammy update: v5.15.87 upstream stable release (LP: #2007441) //
+    CVE-2022-41218 is assigned to those bugs above.
+    - media: dvb-core: Fix UAF due to refcount races at releasing
+
+  * RaptorLake: Fix the Screen is shaking by onboard HDMI port in mirror mode
+    (LP: #1993561)
+    - drm/i915/display: Drop check for doublescan mode in modevalid
+    - drm/i915/display: Prune Interlace modes for Display >=12
+
+  * CVE-2023-0266 // CVE-2023-0266 was assigned for this issue.
+    - ALSA: pcm: Move rwsem lock inside snd_ctl_elem_read to prevent UAF
+
+  * CVE-2022-4382
+    - USB: gadgetfs: Fix race between mounting and unmounting
+
+  * CVE-2022-2196
+    - KVM: VMX: Execute IBPB on emulated VM-exit when guest has IBRS
+
+  * ubuntu_kernel_selftests: net:udpgso_bench.sh failed (LP: #1951447)
+    - selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
+
+  * net:fcnal-test.sh didn't return a non-zero value even with some sub-tests
+    failed (LP: #2006692)
+    - selftests: net/fcnal-test.sh: add exit code
+
+  * LXD containers using shiftfs on ZFS or TMPFS broken on 5.15.0-48.54
+    (LP: #1990849)
+    - SAUCE: shiftfs: always rely on init_user_ns
+    - [SAUCE] shiftfs: fix -EOVERFLOW inside the container
+
+  * Regression in ext4 during online resize (LP: #2003816)
+    - ext4: fix bad checksum after online resize
+    - ext4: fix corruption when online resizing a 1K bigalloc fs
+    - SAUCE: Export ext4_superblock_csum function
+    - ext4: fix corrupt backup group descriptors after online resize
+
+  * Jammy update: v5.15.86 upstream stable release (LP: #2005113)
+    - usb: musb: remove extra check in musb_gadget_vbus_draw
+    - arm64: dts: qcom: ipq6018-cp01-c1: use BLSPI1 pins
+    - arm64: dts: qcom: sm8250-sony-xperia-edo: fix touchscreen bias-disable
+    - arm64: dts: qcom: msm8996: Add MSM8996 Pro support
+    - arm64: dts: qcom: msm8996: fix supported-hw in cpufreq OPP tables
+    - arm64: dts: qcom: msm8996: fix GPU OPP table
+    - ARM: dts: qcom: apq8064: fix coresight compatible
+    - arm64: dts: qcom: sdm630: fix UART1 pin bias
+    - arm64: dts: qcom: sdm845-cheza: fix AP suspend pin bias
+    - arm64: dts: qcom: msm8916: Drop MSS fallback compatible
+    - objtool, kcsan: Add volatile read/write instrumentation to whitelist
+    - ARM: dts: stm32: Drop stm32mp15xc.dtsi from Avenger96
+    - ARM: dts: stm32: Fix AV96 WLAN regulator gpio property
+    - drivers: soc: ti: knav_qmss_queue: Mark knav_acc_firmwares as static
+    - arm64: dts: qcom: pm660: Use unique ADC5_VCOIN address in node name
+    - arm64: dts: qcom: sm8250: correct LPASS pin pull down
+    - soc: qcom: llcc: make irq truly optional
+    - arm64: dts: qcom: Correct QMP PHY child node name
+    - arm64: dts: qcom: sm8150: fix UFS PHY registers
+    - arm64: dts: qcom: sm8250: fix UFS PHY registers
+    - arm64: dts: qcom: sm8350: fix UFS PHY registers
+    - arm64: dts: qcom: sm8250: drop bogus DP PHY clock
+    - soc: qcom: apr: make code more reuseable
+    - soc: qcom: apr: Add check for idr_alloc and of_property_read_string_index
+    - arm64: dts: qcom: sm6125: fix SDHCI CQE reg names
+    - arm: dts: spear600: Fix clcd interrupt
+    - soc: ti: knav_qmss_queue: Use pm_runtime_resume_and_get instead of
+      pm_runtime_get_sync
+    - soc: ti: knav_qmss_queue: Fix PM disable depth imbalance in knav_queue_probe
+    - soc: ti: smartreflex: Fix PM disable depth imbalance in omap_sr_probe
+    - arm64: Treat ESR_ELx as a 64-bit register
+    - arm64: mm: kfence: only handle translation faults
+    - perf: arm_dsu: Fix hotplug callback leak in dsu_pmu_init()
+    - perf/arm_dmc620: Fix hotplug callback leak in dmc620_pmu_init()
+    - perf/smmuv3: Fix hotplug callback leak in arm_smmu_pmu_init()
+    - arm64: dts: ti: k3-am65-main: Drop dma-coherent in crypto node
+    - arm64: dts: ti: k3-j721e-main: Drop dma-coherent in crypto node
+    - ARM: dts: nuvoton: Remove bogus unit addresses from fixed-partition nodes
+    - arm64: dts: mt6779: Fix devicetree build warnings
+    - arm64: dts: mt2712e: Fix unit_address_vs_reg warning for oscillators
+    - arm64: dts: mt2712e: Fix unit address for pinctrl node
+    - arm64: dts: mt2712-evb: Fix vproc fixed regulators unit names
+    - arm64: dts: mt2712-evb: Fix usb vbus regulators unit names
+    - arm64: dts: mediatek: pumpkin-common: Fix devicetree warnings
+    - arm64: dts: mediatek: mt6797: Fix 26M oscillator unit name
+    - ARM: dts: dove: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-370: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-xp: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-375: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-38x: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-39x: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: turris-omnia: Add ethernet aliases
+    - ARM: dts: turris-omnia: Add switch port 6 node
+    - arm64: dts: armada-3720-turris-mox: Add missing interrupt for RTC
+    - seccomp: Move copy_seccomp() to no failure path.
+    - pstore/ram: Fix error return code in ramoops_probe()
+    - ARM: mmp: fix timer_read delay
+    - pstore: Avoid kcore oops by vmap()ing with VM_IOREMAP
+    - tpm/tpm_ftpm_tee: Fix error handling in ftpm_mod_init()
+    - tpm/tpm_crb: Fix error message in __crb_relinquish_locality()
+    - ovl: store lower path in ovl_inode
+    - ovl: use ovl_copy_{real,upper}attr() wrappers
+    - ovl: remove privs in ovl_copyfile()
+    - ovl: remove privs in ovl_fallocate()
+    - sched/fair: Cleanup task_util and capacity type
+    - sched/uclamp: Fix relationship between uclamp and migration margin
+    - sched/uclamp: Make task_fits_capacity() use util_fits_cpu()
+    - sched/uclamp: Make select_idle_capacity() use util_fits_cpu()
+    - sched/fair: Removed useless update of p->recent_used_cpu
+    - sched/core: Introduce sched_asym_cpucap_active()
+    - sched/uclamp: Make asym_fits_capacity() use util_fits_cpu()
+    - cpuidle: dt: Return the correct numbers of parsed idle states
+    - alpha: fix TIF_NOTIFY_SIGNAL handling
+    - alpha: fix syscall entry in !AUDUT_SYSCALL case
+    - x86/sgx: Reduce delay and interference of enclave release
+    - PM: hibernate: Fix mistake in kerneldoc comment
+    - fs: don't audit the capability check in simple_xattr_list()
+    - cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut()
+    - selftests/ftrace: event_triggers: wait longer for test_event_enable
+    - perf: Fix possible memleak in pmu_dev_alloc()
+    - lib/debugobjects: fix stat count and optimize debug_objects_mem_init
+    - platform/x86: huawei-wmi: fix return value calculation
+    - timerqueue: Use rb_entry_safe() in timerqueue_getnext()
+    - proc: fixup uptime selftest
+    - lib/fonts: fix undefined behavior in bit shift for get_default_font
+    - ocfs2: fix memory leak in ocfs2_stack_glue_init()
+    - MIPS: vpe-mt: fix possible memory leak while module exiting
+    - MIPS: vpe-cmp: fix possible memory leak while module exiting
+    - selftests/efivarfs: Add checking of the test return value
+    - PNP: fix name memory leak in pnp_alloc_dev()
+    - perf/x86/intel/uncore: Fix reference count leak in sad_cfg_iio_topology()
+    - perf/x86/intel/uncore: Fix reference count leak in hswep_has_limit_sbox()
+    - perf/x86/intel/uncore: Fix reference count leak in snr_uncore_mmio_map()
+    - perf/x86/intel/uncore: Fix reference count leak in __uncore_imc_init_box()
+    - platform/chrome: cros_usbpd_notify: Fix error handling in
+      cros_usbpd_notify_init()
+    - thermal: core: fix some possible name leaks in error paths
+    - irqchip: gic-pm: Use pm_runtime_resume_and_get() in gic_probe()
+    - irqchip/wpcm450: Fix memory leak in wpcm450_aic_of_init()
+    - EDAC/i10nm: fix refcount leak in pci_get_dev_wrapper()
+    - SUNRPC: Return true/false (not 1/0) from bool functions
+    - NFSD: Finish converting the NFSv2 GETACL result encoder
+    - nfsd: don't call nfsd_file_put from client states seqfile display
+    - genirq/irqdesc: Don't try to remove non-existing sysfs files
+    - cpufreq: amd_freq_sensitivity: Add missing pci_dev_put()
+    - libfs: add DEFINE_SIMPLE_ATTRIBUTE_SIGNED for signed value
+    - lib/notifier-error-inject: fix error when writing -errno to debugfs file
+    - debugfs: fix error when writing negative value to atomic_t debugfs file
+    - rapidio: fix possible name leaks when rio_add_device() fails
+    - rapidio: rio: fix possible name leak in rio_register_mport()
+    - clocksource/drivers/sh_cmt: Access registers according to spec
+    - mips: ralink: mt7621: define MT7621_SYSC_BASE with __iomem
+    - mips: ralink: mt7621: soc queries and tests as functions
+    - mips: ralink: mt7621: do not use kzalloc too early
+    - futex: Move to kernel/futex/
+    - futex: Resend potentially swallowed owner death notification
+    - cpu/hotplug: Make target_store() a nop when target == state
+    - cpu/hotplug: Do not bail-out in DYING/STARTING sections
+    - clocksource/drivers/timer-ti-dm: Fix missing clk_disable_unprepare in
+      dmtimer_systimer_init_clock()
+    - ACPICA: Fix use-after-free in acpi_ut_copy_ipackage_to_ipackage()
+    - uprobes/x86: Allow to probe a NOP instruction with 0x66 prefix
+    - x86/xen: Fix memory leak in xen_smp_intr_init{_pv}()
+    - x86/xen: Fix memory leak in xen_init_lock_cpu()
+    - xen/privcmd: Fix a possible warning in privcmd_ioctl_mmap_resource()
+    - PM: runtime: Do not call __rpm_callback() from rpm_idle()
+    - platform/chrome: cros_ec_typec: Cleanup switch handle return paths
+    - platform/chrome: cros_ec_typec: zero out stale pointers
+    - platform/x86: mxm-wmi: fix memleak in mxm_wmi_call_mx[ds|mx]()
+    - platform/x86: intel_scu_ipc: fix possible name leak in
+      __intel_scu_ipc_register()
+    - MIPS: BCM63xx: Add check for NULL for clk in clk_enable
+    - MIPS: OCTEON: warn only once if deprecated link status is being used
+    - lockd: set other missing fields when unlocking files
+    - fs: sysv: Fix sysv_nblocks() returns wrong value
+    - rapidio: fix possible UAF when kfifo_alloc() fails
+    - eventfd: change int to __u64 in eventfd_signal() ifndef CONFIG_EVENTFD
+    - relay: fix type mismatch when allocating memory in relay_create_buf()
+    - hfs: Fix OOB Write in hfs_asc2mac
+    - rapidio: devices: fix missing put_device in mport_cdev_open
+    - platform/mellanox: mlxbf-pmc: Fix event typo
+    - wifi: ath9k: hif_usb: fix memory leak of urbs in
+      ath9k_hif_usb_dealloc_tx_urbs()
+    - wifi: ath9k: hif_usb: Fix use-after-free in ath9k_hif_usb_reg_in_cb()
+    - wifi: rtl8xxxu: Fix reading the vendor of combo chips
+    - drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge
+    - libbpf: Fix use-after-free in btf_dump_name_dups
+    - libbpf: Fix null-pointer dereference in find_prog_by_sec_insn()
+    - ata: libata: move ata_{port,link,dev}_dbg to standard pr_XXX() macros
+    - ata: add/use ata_taskfile::{error|status} fields
+    - ata: libata: fix NCQ autosense logic
+    - ipmi: kcs: Poll OBF briefly to reduce OBE latency
+    - drm/amdgpu/powerplay/psm: Fix memory leak in power state init
+    - media: v4l2-ctrls: Fix off-by-one error in integer menu control check
+    - media: coda: jpeg: Add check for kmalloc
+    - media: adv748x: afe: Select input port when initializing AFE
+    - media: i2c: ad5820: Fix error path
+    - venus: pm_helpers: Fix error check in vcodec_domains_get()
+    - soreuseport: Fix socket selection for SO_INCOMING_CPU.
+    - media: exynos4-is: don't rely on the v4l2_async_subdev internals
+    - libbpf: Btf dedup identical struct test needs check for nested
+      structs/arrays
+    - can: kvaser_usb: do not increase tx statistics when sending error message
+      frames
+    - can: kvaser_usb: kvaser_usb_leaf: Get capabilities from device
+    - can: kvaser_usb: kvaser_usb_leaf: Rename {leaf,usbcan}_cmd_error_event to
+      {leaf,usbcan}_cmd_can_error_event
+    - can: kvaser_usb: kvaser_usb_leaf: Handle CMD_ERROR_EVENT
+    - can: kvaser_usb_leaf: Set Warning state even without bus errors
+    - can: kvaser_usb: make use of units.h in assignment of frequency
+    - can: kvaser_usb_leaf: Fix improved state not being reported
+    - can: kvaser_usb_leaf: Fix wrong CAN state after stopping
+    - can: kvaser_usb_leaf: Fix bogus restart events
+    - can: kvaser_usb: Add struct kvaser_usb_busparams
+    - can: kvaser_usb: Compare requested bittiming parameters with actual
+      parameters in do_set_{,data}_bittiming
+    - drm/rockchip: lvds: fix PM usage counter unbalance in poweron
+    - clk: renesas: r9a06g032: Repair grave increment error
+    - spi: Update reference to struct spi_controller
+    - drm/panel/panel-sitronix-st7701: Remove panel on DSI attach failure
+    - drm/msm/hdmi: drop unused GPIO support
+    - drm/msm/hdmi: use devres helper for runtime PM management
+    - bpf: Fix slot type check in check_stack_write_var_off
+    - media: vivid: fix compose size exceed boundary
+    - media: platform: exynos4-is: fix return value check in fimc_md_probe()
+    - bpf: propagate precision in ALU/ALU64 operations
+    - bpf: Check the other end of slot_type for STACK_SPILL
+    - bpf: propagate precision across all frames, not just the last one
+    - clk: qcom: gcc-sm8250: Use retention mode for USB GDSCs
+    - mtd: Fix device name leak when register device failed in add_mtd_device()
+    - Input: joystick - fix Kconfig warning for JOYSTICK_ADC
+    - wifi: rsi: Fix handling of 802.3 EAPOL frames sent via control port
+    - media: camss: Clean up received buffers on failed start of streaming
+    - net, proc: Provide PROC_FS=n fallback for proc_create_net_single_write()
+    - rxrpc: Fix ack.bufferSize to be 0 when generating an ack
+    - bfq: fix waker_bfqq inconsistency crash
+    - drm/radeon: Add the missed acpi_put_table() to fix memory leak
+    - drm/mediatek: Modify dpi power on/off sequence.
+    - ASoC: pxa: fix null-pointer dereference in filter()
+    - libbpf: Fix uninitialized warning in btf_dump_dump_type_data
+    - nvmet: only allocate a single slab for bvecs
+    - regulator: core: fix unbalanced of node refcount in regulator_dev_lookup()
+    - amdgpu/pm: prevent array underflow in vega20_odn_edit_dpm_table()
+    - nvme: return err on nvme_init_non_mdts_limits fail
+    - regulator: qcom-rpmh: Fix PMR735a S3 regulator spec
+    - drm/fourcc: Add packed 10bit YUV 4:2:0 format
+    - drm/fourcc: Fix vsub/hsub for Q410 and Q401
+    - integrity: Fix memory leakage in keyring allocation error path
+    - ima: Fix misuse of dereference of pointer in template_desc_init_fields()
+    - block: clear ->slave_dir when dropping the main slave_dir reference
+    - wifi: ath10k: Fix return value in ath10k_pci_init()
+    - drm/msm/a6xx: Fix speed-bin detection vs probe-defer
+    - mtd: lpddr2_nvm: Fix possible null-ptr-deref
+    - Input: elants_i2c - properly handle the reset GPIO when power is off
+    - media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init()
+    - media: solo6x10: fix possible memory leak in solo_sysfs_init()
+    - media: platform: exynos4-is: Fix error handling in fimc_md_init()
+    - media: videobuf-dma-contig: use dma_mmap_coherent
+    - inet: add READ_ONCE(sk->sk_bound_dev_if) in inet_csk_bind_conflict()
+    - mtd: spi-nor: hide jedec_id sysfs attribute if not present
+    - mtd: spi-nor: Fix the number of bytes for the dummy cycles
+    - bpf: Move skb->len == 0 checks into __bpf_redirect
+    - HID: hid-sensor-custom: set fixed size for custom attributes
+    - pinctrl: k210: call of_node_put()
+    - ALSA: pcm: fix undefined behavior in bit shift for SNDRV_PCM_RATE_KNOT
+    - ALSA: seq: fix undefined behavior in bit shift for
+      SNDRV_SEQ_FILTER_USE_EVENT
+    - regulator: core: use kfree_const() to free space conditionally
+    - clk: rockchip: Fix memory leak in rockchip_clk_register_pll()
+    - drm/amdgpu: fix pci device refcount leak
+    - bonding: fix link recovery in mode 2 when updelay is nonzero
+    - mtd: maps: pxa2xx-flash: fix memory leak in probe
+    - drbd: remove call to memset before free device/resource/connection
+    - drbd: destroy workqueue when drbd device was freed
+    - ASoC: qcom: Add checks for devm_kcalloc
+    - media: vimc: Fix wrong function called when vimc_init() fails
+    - media: imon: fix a race condition in send_packet()
+    - clk: imx8mn: rename vpu_pll to m7_alt_pll
+    - clk: imx: replace osc_hdmi with dummy
+    - clk: imx8mn: fix imx8mn_sai2_sels clocks list
+    - clk: imx8mn: fix imx8mn_enet_phy_sels clocks list
+    - pinctrl: pinconf-generic: add missing of_node_put()
+    - media: dvb-core: Fix ignored return value in dvb_register_frontend()
+    - media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()
+    - media: s5p-mfc: Add variant data for MFC v7 hardware for Exynos 3250 SoC
+    - drm/tegra: Add missing clk_disable_unprepare() in tegra_dc_probe()
+    - ASoC: dt-bindings: wcd9335: fix reset line polarity in example
+    - ASoC: mediatek: mtk-btcvsd: Add checks for write and read of mtk_btcvsd_snd
+    - NFSv4.2: Clear FATTR4_WORD2_SECURITY_LABEL when done decoding
+    - NFSv4.2: Fix a memory stomp in decode_attr_security_label
+    - NFSv4.2: Fix initialisation of struct nfs4_label
+    - NFSv4: Fix a credential leak in _nfs4_discover_trunking()
+    - NFSv4: Fix a deadlock between nfs4_open_recover_helper() and delegreturn
+    - NFS: Fix an Oops in nfs_d_automount()
+    - ALSA: asihpi: fix missing pci_disable_device()
+    - wifi: iwlwifi: mvm: fix double free on tx path.
+    - ASoC: mediatek: mt8173: Fix debugfs registration for components
+    - ASoC: mediatek: mt8173: Enable IRQ when pdata is ready
+    - drm/amd/pm/smu11: BACO is supported when it's in BACO state
+    - drm/radeon: Fix PCI device refcount leak in radeon_atrm_get_bios()
+    - drm/amdgpu: Fix PCI device refcount leak in amdgpu_atrm_get_bios()
+    - drm/amdkfd: Fix memory leakage
+    - ASoC: pcm512x: Fix PM disable depth imbalance in pcm512x_probe
+    - netfilter: conntrack: set icmpv6 redirects as RELATED
+    - Input: wistron_btns - disable on UML
+    - bpf, sockmap: Fix repeated calls to sock_put() when msg has more_data
+    - bpf, sockmap: Fix missing BPF_F_INGRESS flag when using apply_bytes
+    - bpf, sockmap: Fix data loss caused by using apply_bytes on ingress redirect
+    - bonding: uninitialized variable in bond_miimon_inspect()
+    - spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
+    - wifi: cfg80211: Fix not unregister reg_pdev when load_builtin_regdb_keys()
+      fails
+    - mt76: stop the radar detector after leaving dfs channel
+    - wifi: mt76: mt7921: fix reporting of TX AGGR histogram
+    - wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
+    - regulator: core: fix module refcount leak in set_supply()
+    - clk: qcom: lpass-sc7180: Fix pm_runtime usage
+    - clk: qcom: clk-krait: fix wrong div2 functions
+    - hsr: Add a rcu-read lock to hsr_forward_skb().
+    - hsr: Avoid double remove of a node.
+    - hsr: Disable netpoll.
+    - hsr: Synchronize sending frames to have always incremented outgoing seq nr.
+    - hsr: Synchronize sequence number updates.
+    - configfs: fix possible memory leak in configfs_create_dir()
+    - regulator: core: fix resource leak in regulator_register()
+    - hwmon: (jc42) Convert register access and caching to regmap/regcache
+    - hwmon: (jc42) Restore the min/max/critical temperatures on resume
+    - bpf, sockmap: fix race in sock_map_free()
+    - ALSA: pcm: Set missing stop_operating flag at undoing trigger start
+    - media: saa7164: fix missing pci_disable_device()
+    - ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
+    - xprtrdma: Fix regbuf data not freed in rpcrdma_req_create()
+    - SUNRPC: Fix missing release socket in rpc_sockname()
+    - NFSv4.x: Fail client initialisation if state manager thread can't run
+    - riscv, bpf: Emit fixed-length instructions for BPF_PSEUDO_FUNC
+    - mmc: alcor: fix return value check of mmc_add_host()
+    - mmc: moxart: fix return value check of mmc_add_host()
+    - mmc: mxcmmc: fix return value check of mmc_add_host()
+    - mmc: pxamci: fix return value check of mmc_add_host()
+    - mmc: rtsx_pci: fix return value check of mmc_add_host()
+    - mmc: rtsx_usb_sdmmc: fix return value check of mmc_add_host()
+    - mmc: toshsd: fix return value check of mmc_add_host()
+    - mmc: vub300: fix return value check of mmc_add_host()
+    - mmc: wmt-sdmmc: fix return value check of mmc_add_host()
+    - mmc: atmel-mci: fix return value check of mmc_add_host()
+    - mmc: omap_hsmmc: fix return value check of mmc_add_host()
+    - mmc: meson-gx: fix return value check of mmc_add_host()
+    - mmc: via-sdmmc: fix return value check of mmc_add_host()
+    - mmc: wbsd: fix return value check of mmc_add_host()
+    - mmc: mmci: fix return value check of mmc_add_host()
+    - mmc: renesas_sdhi: alway populate SCC pointer
+    - memstick: ms_block: Add error handling support for add_disk()
+    - memstick/ms_block: Add check for alloc_ordered_workqueue
+    - mmc: core: Normalize the error handling branch in sd_read_ext_regs()
+    - regulator: qcom-labibb: Fix missing of_node_put() in
+      qcom_labibb_regulator_probe()
+    - media: c8sectpfe: Add of_node_put() when breaking out of loop
+    - media: coda: Add check for dcoda_iram_alloc
+    - media: coda: Add check for kmalloc
+    - clk: samsung: Fix memory leak in _samsung_clk_register_pll()
+    - spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
+    - wifi: rtl8xxxu: Add __packed to struct rtl8723bu_c2h
+    - wifi: rtl8xxxu: Fix the channel width reporting
+    - wifi: brcmfmac: Fix error return code in brcmf_sdio_download_firmware()
+    - blktrace: Fix output non-blktrace event when blk_classic option enabled
+    - bpf: Do not zero-extend kfunc return values
+    - clk: socfpga: Fix memory leak in socfpga_gate_init()
+    - net: vmw_vsock: vmci: Check memcpy_from_msg()
+    - net: defxx: Fix missing err handling in dfx_init()
+    - net: stmmac: selftests: fix potential memleak in stmmac_test_arpoffload()
+    - net: stmmac: fix possible memory leak in stmmac_dvr_probe()
+    - drivers: net: qlcnic: Fix potential memory leak in qlcnic_sriov_init()
+    - of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry()
+      and find_dup_cset_prop()
+    - ethernet: s2io: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: farsync: Fix kmemleak when rmmods farsync
+    - net/tunnel: wait until all sk_user_data reader finish before releasing the
+      sock
+    - net: apple: mace: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: apple: bmac: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: emaclite: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: ethernet: dnet: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - hamradio: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: amd: lance: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - af_unix: call proto_unregister() in the error path in af_unix_init()
+    - net: amd-xgbe: Fix logic around active and passive cables
+    - net: amd-xgbe: Check only the minimum speed for active/passive cables
+    - can: tcan4x5x: Remove invalid write in clear_interrupts
+    - can: m_can: Call the RAM init directly from m_can_chip_config
+    - can: tcan4x5x: Fix use of register error status mask
+    - net: lan9303: Fix read error execution path
+    - ntb_netdev: Use dev_kfree_skb_any() in interrupt context
+    - sctp: sysctl: make extra pointers netns aware
+    - Bluetooth: MGMT: Fix error report for ADD_EXT_ADV_PARAMS
+    - Bluetooth: btintel: Fix missing free skb in btintel_setup_combined()
+    - Bluetooth: btusb: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_qca: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_ll: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_h5: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_bcsp: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_core: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: RFCOMM: don't call kfree_skb() under spin_lock_irqsave()
+    - stmmac: fix potential division by 0
+    - i40e: Fix the inability to attach XDP program on downed interface
+    - net: dsa: tag_8021q: avoid leaking ctx on dsa_tag_8021q_register() error
+      path
+    - apparmor: fix a memleak in multi_transaction_new()
+    - apparmor: fix lockdep warning when removing a namespace
+    - apparmor: Fix abi check to include v8 abi
+    - crypto: hisilicon/qm - fix missing destroy qp_idr
+    - crypto: sun8i-ss - use dma_addr instead u32
+    - crypto: nitrox - avoid double free on error path in nitrox_sriov_init()
+    - scsi: core: Fix a race between scsi_done() and scsi_timeout()
+    - apparmor: Use pointer to struct aa_label for lbs_cred
+    - PCI: dwc: Fix n_fts[] array overrun
+    - RDMA/core: Fix order of nldev_exit call
+    - PCI: pci-epf-test: Register notifier if only core_init_notifier is enabled
+    - f2fs: Fix the race condition of resize flag between resizefs
+    - crypto: rockchip - do not do custom power management
+    - crypto: rockchip - do not store mode globally
+    - crypto: rockchip - add fallback for cipher
+    - crypto: rockchip - add fallback for ahash
+    - crypto: rockchip - better handle cipher key
+    - crypto: rockchip - remove non-aligned handling
+    - crypto: rockchip - rework by using crypto_engine
+    - apparmor: Fix memleak in alloc_ns()
+    - f2fs: fix to invalidate dcc->f2fs_issue_discard in error path
+    - f2fs: fix normal discard process
+    - f2fs: fix to destroy sbi->post_read_wq in error path of f2fs_fill_super()
+    - RDMA/irdma: Report the correct link speed
+    - scsi: qla2xxx: Fix set-but-not-used variable warnings
+    - RDMA/siw: Fix immediate work request flush to completion queue
+    - IB/mad: Don't call to function that might sleep while in atomic context
+    - RDMA/restrack: Release MR restrack when delete
+    - RDMA/core: Make sure "ib_port" is valid when access sysfs node
+    - RDMA/nldev: Return "-EAGAIN" if the cm_id isn't from expected port
+    - RDMA/siw: Set defined status for work completion with undefined status
+    - scsi: scsi_debug: Fix a warning in resp_write_scat()
+    - crypto: ccree - Remove debugfs when platform_driver_register failed
+    - crypto: cryptd - Use request context instead of stack for sub-request
+    - crypto: hisilicon/qm - add missing pci_dev_put() in q_num_set()
+    - RDMA/hns: Repacing 'dseg_len' by macros in fill_ext_sge_inl_data()
+    - RDMA/hns: Fix ext_sge num error when post send
+    - PCI: Check for alloc failure in pci_request_irq()
+    - RDMA/hfi: Decrease PCI device reference count in error path
+    - crypto: ccree - Make cc_debugfs_global_fini() available for module init
+      function
+    - RDMA/hns: fix memory leak in hns_roce_alloc_mr()
+    - RDMA/rxe: Fix NULL-ptr-deref in rxe_qp_do_cleanup() when socket create
+      failed
+    - dt-bindings: imx6q-pcie: Fix clock names for imx6sx and imx8mq
+    - dt-bindings: visconti-pcie: Fix interrupts array max constraints
+    - scsi: hpsa: Fix possible memory leak in hpsa_init_one()
+    - crypto: tcrypt - Fix multibuffer skcipher speed test mem leak
+    - padata: Always leave BHs disabled when running ->parallel()
+    - padata: Fix list iterator in padata_do_serial()
+    - scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add()
+    - scsi: hpsa: Fix error handling in hpsa_add_sas_host()
+    - scsi: hpsa: Fix possible memory leak in hpsa_add_sas_device()
+    - scsi: efct: Fix possible memleak in efct_device_init()
+    - scsi: scsi_debug: Fix a warning in resp_verify()
+    - scsi: scsi_debug: Fix a warning in resp_report_zones()
+    - scsi: fcoe: Fix possible name leak when device_register() fails
+    - scsi: scsi_debug: Fix possible name leak in sdebug_add_host_helper()
+    - scsi: ipr: Fix WARNING in ipr_init()
+    - scsi: fcoe: Fix transport not deattached when fcoe_if_init() fails
+    - scsi: snic: Fix possible UAF in snic_tgt_create()
+    - RDMA/nldev: Add checks for nla_nest_start() in fill_stat_counter_qps()
+    - f2fs: avoid victim selection from previous victim section
+    - RDMA/nldev: Fix failure to send large messages
+    - crypto: amlogic - Remove kcalloc without check
+    - crypto: omap-sham - Use pm_runtime_resume_and_get() in omap_sham_probe()
+    - riscv/mm: add arch hook arch_clear_hugepage_flags
+    - RDMA/hfi1: Fix error return code in parse_platform_config()
+    - RDMA/srp: Fix error return code in srp_parse_options()
+    - PCI: mt7621: Rename mt7621_pci_ to mt7621_pcie_
+    - PCI: mt7621: Add sentinel to quirks table
+    - orangefs: Fix sysfs not cleanup when dev init failed
+    - RDMA/hns: Fix AH attr queried by query_qp
+    - RDMA/hns: Fix PBL page MTR find
+    - RDMA/hns: Fix page size cap from firmware
+    - RDMA/hns: Fix error code of CMD
+    - crypto: img-hash - Fix variable dereferenced before check 'hdev->req'
+    - hwrng: amd - Fix PCI device refcount leak
+    - hwrng: geode - Fix PCI device refcount leak
+    - IB/IPoIB: Fix queue count inconsistency for PKEY child interfaces
+    - RISC-V: Align the shadow stack
+    - drivers: dio: fix possible memory leak in dio_init()
+    - serial: tegra: Read DMA status before terminating
+    - serial: 8250_bcm7271: Fix error handling in brcmuart_init()
+    - class: fix possible memory leak in __class_register()
+    - vfio: platform: Do not pass return buffer to ACPI _RST method
+    - uio: uio_dmem_genirq: Fix missing unlock in irq configuration
+    - uio: uio_dmem_genirq: Fix deadlock between irq config and handling
+    - usb: fotg210-udc: Fix ages old endianness issues
+    - staging: vme_user: Fix possible UAF in tsi148_dma_list_add
+    - usb: typec: Check for ops->exit instead of ops->enter in altmode_exit
+    - usb: typec: tcpci: fix of node refcount leak in tcpci_register_port()
+    - usb: typec: tipd: Cleanup resources if devm_tps6598_psy_register fails
+    - usb: typec: tipd: Fix spurious fwnode_handle_put in error path
+    - extcon: usbc-tusb320: Add support for mode setting and reset
+    - extcon: usbc-tusb320: Add support for TUSB320L
+    - usb: typec: Factor out non-PD fwnode properties
+    - extcon: usbc-tusb320: Factor out extcon into dedicated functions
+    - extcon: usbc-tusb320: Add USB TYPE-C support
+    - extcon: usbc-tusb320: Update state on probe even if no IRQ pending
+    - serial: amba-pl011: avoid SBSA UART accessing DMACR register
+    - serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
+    - serial: stm32: move dma_request_chan() before clk_prepare_enable()
+    - serial: pch: Fix PCI device refcount leak in pch_request_dma()
+    - tty: serial: clean up stop-tx part in altera_uart_tx_chars()
+    - tty: serial: altera_uart_{r,t}x_chars() need only uart_port
+    - serial: altera_uart: fix locking in polling mode
+    - serial: sunsab: Fix error handling in sunsab_init()
+    - test_firmware: fix memory leak in test_firmware_init()
+    - misc: ocxl: fix possible name leak in ocxl_file_register_afu()
+    - ocxl: fix pci device refcount leak when calling get_function_0()
+    - misc: tifm: fix possible memory leak in tifm_7xx1_switch_media()
+    - misc: sgi-gru: fix use-after-free error in gru_set_context_option, gru_fault
+      and gru_handle_user_call_os
+    - firmware: raspberrypi: fix possible memory leak in rpi_firmware_probe()
+    - cxl: fix possible null-ptr-deref in cxl_guest_init_afu|adapter()
+    - cxl: fix possible null-ptr-deref in cxl_pci_init_afu|adapter()
+    - iio: temperature: ltc2983: make bulk write buffer DMA-safe
+    - iio: adis: handle devices that cannot unmask the drdy pin
+    - iio: adis: stylistic changes
+    - iio:imu:adis: Move exports into IIO_ADISLIB namespace
+    - iio: adis: add '__adis_enable_irq()' implementation
+    - counter: stm32-lptimer-cnt: fix the check on arr and cmp registers update
+    - coresight: trbe: remove cpuhp instance node before remove cpuhp state
+    - usb: roles: fix of node refcount leak in usb_role_switch_is_parent()
+    - usb: gadget: f_hid: fix f_hidg lifetime vs cdev
+    - usb: gadget: f_hid: fix refcount leak on error path
+    - drivers: mcb: fix resource leak in mcb_probe()
+    - mcb: mcb-parse: fix error handing in chameleon_parse_gdd()
+    - chardev: fix error handling in cdev_device_add()
+    - i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
+    - staging: rtl8192u: Fix use after free in ieee80211_rx()
+    - staging: rtl8192e: Fix potential use-after-free in rtllib_rx_Monitor()
+    - vme: Fix error not catched in fake_init()
+    - gpiolib: Get rid of redundant 'else'
+    - gpiolib: cdev: fix NULL-pointer dereferences
+    - gpiolib: make struct comments into real kernel docs
+    - gpiolib: protect the GPIO device against being dropped while in use by user-
+      space
+    - i2c: mux: reg: check return value after calling platform_get_resource()
+    - i2c: ismt: Fix an out-of-bounds bug in ismt_access()
+    - usb: storage: Add check for kcalloc
+    - tracing/hist: Fix issue of losting command info in error_log
+    - ksmbd: Fix resource leak in ksmbd_session_rpc_open()
+    - samples: vfio-mdev: Fix missing pci_disable_device() in mdpy_fb_probe()
+    - thermal/drivers/imx8mm_thermal: Validate temperature range
+    - thermal/drivers/qcom/temp-alarm: Fix inaccurate warning for gen2
+    - thermal/drivers/qcom/lmh: Fix irq handler return value
+    - fbdev: ssd1307fb: Drop optional dependency
+    - fbdev: pm2fb: fix missing pci_disable_device()
+    - fbdev: via: Fix error in via_core_init()
+    - fbdev: vermilion: decrease reference count in error path
+    - fbdev: ep93xx-fb: Add missing clk_disable_unprepare in ep93xxfb_probe()
+    - fbdev: geode: don't build on UML
+    - fbdev: uvesafb: don't build on UML
+    - fbdev: uvesafb: Fixes an error handling path in uvesafb_probe()
+    - HSI: omap_ssi_core: fix unbalanced pm_runtime_disable()
+    - HSI: omap_ssi_core: fix possible memory leak in ssi_probe()
+    - power: supply: fix residue sysfs file in error handle route of
+      __power_supply_register()
+    - perf trace: Return error if a system call doesn't exist
+    - perf trace: Use macro RAW_SYSCALL_ARGS_NUM to replace number
+    - perf trace: Handle failure when trace point folder is missed
+    - perf symbol: correction while adjusting symbol
+    - power: supply: z2_battery: Fix possible memleak in z2_batt_probe()
+    - HSI: omap_ssi_core: Fix error handling in ssi_init()
+    - power: supply: ab8500: Fix error handling in ab8500_charger_init()
+    - power: supply: fix null pointer dereferencing in
+      power_supply_get_battery_info
+    - perf stat: Refactor __run_perf_stat() common code
+    - perf stat: Do not delay the workload with --delay
+    - RDMA/siw: Fix pointer cast warning
+    - fs/ntfs3: Avoid UBSAN error on true_sectors_per_clst()
+    - overflow: Implement size_t saturating arithmetic helpers
+    - fs/ntfs3: Harden against integer overflows
+    - iommu/sun50i: Fix reset release
+    - iommu/sun50i: Consider all fault sources for reset
+    - iommu/sun50i: Fix R/W permission check
+    - iommu/sun50i: Fix flush size
+    - iommu/rockchip: fix permission bits in page table entries v2
+    - phy: usb: s2 WoL wakeup_count not incremented for USB->Eth devices
+    - include/uapi/linux/swab: Fix potentially missing __always_inline
+    - pwm: tegra: Improve required rate calculation
+    - fs/ntfs3: Fix slab-out-of-bounds read in ntfs_trim_fs
+    - dmaengine: idxd: Fix crc_val field for completion record
+    - rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0
+    - rtc: cmos: Fix event handler registration ordering issue
+    - rtc: cmos: Fix wake alarm breakage
+    - rtc: cmos: fix build on non-ACPI platforms
+    - rtc: cmos: Call cmos_wake_setup() from cmos_do_probe()
+    - rtc: cmos: Call rtc_wake_setup() from cmos_do_probe()
+    - rtc: cmos: Eliminate forward declarations of some functions
+    - rtc: cmos: Rename ACPI-related functions
+    - rtc: cmos: Disable ACPI RTC event on removal
+    - rtc: snvs: Allow a time difference on clock register read
+    - rtc: pcf85063: Fix reading alarm
+    - iommu/amd: Fix pci device refcount leak in ppr_notifier()
+    - iommu/fsl_pamu: Fix resource leak in fsl_pamu_probe()
+    - macintosh: fix possible memory leak in macio_add_one_device()
+    - macintosh/macio-adb: check the return value of ioremap()
+    - powerpc/52xx: Fix a resource leak in an error handling path
+    - cxl: Fix refcount leak in cxl_calc_capp_routing
+    - powerpc/xmon: Fix -Wswitch-unreachable warning in bpt_cmds
+    - powerpc/xive: add missing iounmap() in error path in
+      xive_spapr_populate_irq_data()
+    - powerpc/perf: callchain validate kernel stack pointer bounds
+    - powerpc/83xx/mpc832x_rdb: call platform_device_put() in error case in
+      of_fsl_spi_probe()
+    - powerpc/hv-gpci: Fix hv_gpci event list
+    - selftests/powerpc: Fix resource leaks
+    - iommu/sun50i: Remove IOMMU_DOMAIN_IDENTITY
+    - pwm: sifive: Call pwm_sifive_update_clock() while mutex is held
+    - pwm: mtk-disp: Fix the parameters calculated by the enabled flag of disp_pwm
+    - pwm: mediatek: always use bus clock for PWM on MT7622
+    - remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()
+    - remoteproc: qcom: q6v5: Fix potential null-ptr-deref in
+      q6v5_wcss_init_mmio()
+    - remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove
+    - remoteproc: qcom_q6v5_pas: detach power domains on remove
+    - remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in
+      adsp_alloc_memory_region()
+    - remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in
+      q6v5_wcss_qcs404_power_on()
+    - powerpc/eeh: Drop redundant spinlock initialization
+    - powerpc/pseries/eeh: use correct API for error log size
+    - mfd: bd957x: Fix Kconfig dependency on REGMAP_IRQ
+    - mfd: qcom_rpm: Fix an error handling path in qcom_rpm_probe()
+    - mfd: pm8008: Remove driver data structure pm8008_data
+    - mfd: pm8008: Fix return value check in pm8008_probe()
+    - netfilter: flowtable: really fix NAT IPv6 offload
+    - rtc: st-lpc: Add missing clk_disable_unprepare in st_rtc_probe()
+    - rtc: pic32: Move devm_rtc_allocate_device earlier in pic32_rtc_probe()
+    - rtc: pcf85063: fix pcf85063_clkout_control
+    - nfsd: under NFSv4.1, fix double svc_xprt_put on rpc_create failure
+    - net: macsec: fix net device access prior to holding a lock
+    - mISDN: hfcsusb: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - mISDN: hfcpci: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - mISDN: hfcmulti: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - block, bfq: fix possible uaf for 'bfqq->bic'
+    - net: enetc: avoid buffer leaks on xdp_do_redirect() failure
+    - nfc: pn533: Clear nfc_target before being used
+    - unix: Fix race in SOCK_SEQPACKET's unix_dgram_sendmsg()
+    - r6040: Fix kmemleak in probe and remove
+    - igc: Enhance Qbv scheduling by using first flag bit
+    - igc: Use strict cycles for Qbv scheduling
+    - igc: Add checking for basetime less than zero
+    - igc: allow BaseTime 0 enrollment for Qbv
+    - igc: recalculate Qbv end_time by considering cycle time
+    - igc: Lift TAPRIO schedule restriction
+    - igc: Set Qbv start_time and end_time to end_time if not being configured in
+      GCL
+    - rtc: mxc_v2: Add missing clk_disable_unprepare()
+    - selftests: devlink: fix the fd redirect in dummy_reporter_test
+    - openvswitch: Fix flow lookup to use unmasked key
+    - soc: mediatek: pm-domains: Fix the power glitch issue
+    - arm64: dts: mt8183: Fix Mali GPU clock
+    - skbuff: Account for tail adjustment during pull operations
+    - mailbox: mpfs: read the system controller's status
+    - mailbox: arm_mhuv2: Fix return value check in mhuv2_probe()
+    - mailbox: zynq-ipi: fix error handling while device_register() fails
+    - net_sched: reject TCF_EM_SIMPLE case for complex ematch module
+    - rxrpc: Fix missing unlock in rxrpc_do_sendmsg()
+    - myri10ge: Fix an error handling path in myri10ge_probe()
+    - net: stream: purge sk_error_queue in sk_stream_kill_queues()
+    - HID: amd_sfh: Add missing check for dma_alloc_coherent
+    - rcu: Fix __this_cpu_read() lockdep warning in rcu_force_quiescent_state()
+    - arm64: make is_ttbrX_addr() noinstr-safe
+    - video: hyperv_fb: Avoid taking busy spinlock on panic path
+    - x86/hyperv: Remove unregister syscore call from Hyper-V cleanup
+    - binfmt_misc: fix shift-out-of-bounds in check_special_flags
+    - fs: jfs: fix shift-out-of-bounds in dbAllocAG
+    - udf: Avoid double brelse() in udf_rename()
+    - jfs: Fix fortify moan in symlink
+    - fs: jfs: fix shift-out-of-bounds in dbDiscardAG
+    - ACPICA: Fix error code path in acpi_ds_call_control_method()
+    - nilfs2: fix shift-out-of-bounds/overflow in nilfs_sb2_bad_offset()
+    - nilfs2: fix shift-out-of-bounds due to too large exponent of block size
+    - acct: fix potential integer overflow in encode_comp_t()
+    - hfs: fix OOB Read in __hfs_brec_find
+    - drm/etnaviv: add missing quirks for GC300
+    - media: imx-jpeg: Disable useless interrupt to avoid kernel panic
+    - brcmfmac: return error when getting invalid max_flowrings from dongle
+    - wifi: ath9k: verify the expected usb_endpoints are present
+    - wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
+    - ASoC: codecs: rt298: Add quirk for KBL-R RVP platform
+    - ipmi: fix memleak when unload ipmi driver
+    - drm/amd/display: prevent memory leak
+    - Revert "drm/amd/display: Limit max DSC target bpp for specific monitors"
+    - qed (gcc13): use u16 for fid to be big enough
+    - bpf: make sure skb->len != 0 when redirecting to a tunneling device
+    - net: ethernet: ti: Fix return type of netcp_ndo_start_xmit()
+    - hamradio: baycom_epp: Fix return type of baycom_send_packet()
+    - wifi: brcmfmac: Fix potential shift-out-of-bounds in
+      brcmf_fw_alloc_request()
+    - igb: Do not free q_vector unless new one was allocated
+    - drm/amdgpu: Fix type of second parameter in trans_msg() callback
+    - drm/amdgpu: Fix type of second parameter in odn_edit_dpm_table() callback
+    - s390/ctcm: Fix return type of ctc{mp,}m_tx()
+    - s390/netiucv: Fix return type of netiucv_tx()
+    - s390/lcs: Fix return type of lcs_start_xmit()
+    - drm/msm: Use drm_mode_copy()
+    - drm/rockchip: Use drm_mode_copy()
+    - drm/sti: Use drm_mode_copy()
+    - drm/mediatek: Fix return type of mtk_hdmi_bridge_mode_valid()
+    - drivers/md/md-bitmap: check the return value of md_bitmap_get_counter()
+    - md/raid1: stop mdx_raid1 thread when raid1 array run failed
+    - drm/amd/display: fix array index out of bound error in bios parser
+    - net: add atomic_long_t to net_device_stats fields
+    - ipv6/sit: use DEV_STATS_INC() to avoid data-races
+    - mrp: introduce active flags to prevent UAF when applicant uninit
+    - ppp: associate skb with a device at tx
+    - bpf: Prevent decl_tag from being referenced in func_proto arg
+    - ethtool: avoiding integer overflow in ethtool_phys_id()
+    - media: dvb-frontends: fix leak of memory fw
+    - media: dvbdev: adopts refcnt to avoid UAF
+    - media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
+    - blk-mq: fix possible memleak when register 'hctx' failed
+    - drm/amd/display: Use the largest vready_offset in pipe group
+    - libbpf: Avoid enum forward-declarations in public API in C++ mode
+    - regulator: core: fix use_count leakage when handling boot-on
+    - wifi: mt76: do not run mt76u_status_worker if the device is not running
+    - mmc: f-sdh30: Add quirks for broken timeout clock capability
+    - mmc: renesas_sdhi: better reset from HS400 mode
+    - media: si470x: Fix use-after-free in si470x_int_in_callback()
+    - clk: st: Fix memory leak in st_of_quadfs_setup()
+    - crypto: hisilicon/hpre - fix resource leak in remove process
+    - scsi: lpfc: Fix hard lockup when reading the rx_monitor from debugfs
+    - scsi: ufs: Reduce the START STOP UNIT timeout
+    - scsi: elx: libefc: Fix second parameter type in state callbacks
+    - hugetlbfs: fix null-ptr-deref in hugetlbfs_parse_param()
+    - drm/fsl-dcu: Fix return type of fsl_dcu_drm_connector_mode_valid()
+    - drm/sti: Fix return type of sti_{dvo,hda,hdmi}_connector_mode_valid()
+    - orangefs: Fix kmemleak in orangefs_prepare_debugfs_help_string()
+    - orangefs: Fix kmemleak in orangefs_{kernel,client}_debug_init()
+    - tools/include: Add _RET_IP_ and math definitions to kernel.h
+    - KVM: selftests: Fix build regression by using accessor function
+    - hwmon: (jc42) Fix missing unlock on error in jc42_write()
+    - ALSA/ASoC: hda: move/rename snd_hdac_ext_stop_streams to hdac_stream.c
+    - ALSA: hda: add snd_hdac_stop_streams() helper
+    - ASoC: Intel: Skylake: Fix driver hang during shutdown
+    - ASoC: mediatek: mt8173-rt5650-rt5514: fix refcount leak in
+      mt8173_rt5650_rt5514_dev_probe()
+    - ASoC: audio-graph-card: fix refcount leak of cpu_ep in
+      __graph_for_each_link()
+    - ASoC: rockchip: pdm: Add missing clk_disable_unprepare() in
+      rockchip_pdm_runtime_resume()
+    - ASoC: mediatek: mt8183: fix refcount leak in
+      mt8183_mt6358_ts3a227_max98357_dev_probe()
+    - ASoC: wm8994: Fix potential deadlock
+    - ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in
+      rk_spdif_runtime_resume()
+    - ASoC: rt5670: Remove unbalanced pm_runtime_put()
+    - drm/i915/display: Don't disable DDI/Transcoder when setting phy test pattern
+    - LoadPin: Ignore the "contents" argument of the LSM hooks
+    - pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion
+    - perf debug: Set debug_peo_args and redirect_to_stderr variable to correct
+      values in perf_quiet_option()
+    - afs: Fix lost servers_outstanding count
+    - pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
+    - ALSA: usb-audio: add the quirk for KT0206 device
+    - ALSA: hda/realtek: Add quirk for Lenovo TianYi510Pro-14IOB
+    - ALSA: hda/hdmi: Add HP Device 0x8711 to force connect list
+    - usb: cdnsp: fix lack of ZLP for ep0
+    - usb: xhci-mtk: fix leakage of shared hcd when fail to set wakeup irq
+    - arm64: dts: qcom: sm8250: fix USB-DP PHY registers
+    - usb: dwc3: Fix race between dwc3_set_mode and __dwc3_set_mode
+    - usb: dwc3: core: defer probe on ulpi_read_id timeout
+    - xhci: Prevent infinite loop in transaction errors recovery for streams
+    - HID: wacom: Ensure bootloader PID is usable in hidraw mode
+    - HID: mcp2221: don't connect hidraw
+    - loop: Fix the max_loop commandline argument treatment when it is set to 0
+    - 9p: set req refcount to zero to avoid uninitialized usage
+    - security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
+    - reiserfs: Add missing calls to reiserfs_security_free()
+    - iio: fix memory leak in iio_device_register_eventset()
+    - iio: adc: ad_sigma_delta: do not use internal iio_dev lock
+    - iio: adc128s052: add proper .data members in adc128_of_match table
+    - regulator: core: fix deadlock on regulator enable
+    - floppy: Fix memory leak in do_floppy_init()
+    - gcov: add support for checksum field
+    - fbdev: fbcon: release buffer when fbcon_do_set_font() failed
+    - ovl: fix use inode directly in rcu-walk mode
+    - btrfs: do not BUG_ON() on ENOMEM when dropping extent items for a range
+    - scsi: qla2xxx: Fix crash when I/O abort times out
+    - net: stmmac: fix errno when create_singlethread_workqueue() fails
+    - media: dvbdev: fix build warning due to comments
+    - media: dvbdev: fix refcnt bug
+    - extcon: usbc-tusb320: Call the Type-C IRQ handler only if a port is
+      registered
+    - mfd: qcom_rpm: Use devm_of_platform_populate() to simplify code
+    - pwm: tegra: Fix 32 bit build
+    - Linux 5.15.86
+
+  * Screen freeze after resuming from suspend (nvme0: I/O timeout)
+    (LP: #1996048) // Jammy update: v5.15.86 upstream stable release
+    (LP: #2005113)
+    - PCI: vmd: Disable MSI remapping after suspend
+
+  * CVE-2023-23559
+    - wifi: rndis_wlan: Prevent buffer overflow in rndis_query_oid
+
+  * CVE-2023-0045
+    - x86/bugs: Flush IBP in ib_prctl_set()
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 24 Feb 2023 11:44:57 +0100
+
+linux (5.15.0-67.74) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-67.74 -proposed tracker (LP: #2008074)
+
+  * [Inspiron 7590, Realtek ALC3254, Speaker, Internal] fails after a while
+    (LP: #2007798)
+    - Revert "ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()"
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 22 Feb 2023 15:01:11 +0100
+
+linux (5.15.0-66.73) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-66.73 -proposed tracker (LP: #2004636)
+
+  * CVE-2023-0461
+    - SAUCE: Fix inet_csk_listen_start after CVE-2023-0461
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 03 Feb 2023 15:04:39 +0100
+
+linux (5.15.0-65.72) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-65.72 -proposed tracker (LP: #2004344)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2023.01.30)
+
+  * NFS: client permission error after adding user to permissible group
+    (LP: #2003053)
+    - NFS: Clear the file access cache upon login
+    - NFS: Judge the file access cache's timestamp in rcu path
+    - NFS: Fix up a sparse warning
+
+  * Fix W6400 hang after resume of S3 stress (LP: #2000299)
+    - drm/amd/display: Manually adjust strobe for DCN303
+
+  * Rear Audio port sometimes has no audio output after reboot(Cirrus Logic)
+    (LP: #1998905)
+    - ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
+
+  * CVE-2022-20369
+    - NFSD: fix use-after-free in __nfs42_ssc_open()
+
+  * CVE-2023-0461
+    - net/ulp: prevent ULP without clone op from entering the LISTEN status
+    - net/ulp: use consistent error code when blocking ULP
+
+  * CVE-2023-0179
+    - netfilter: nft_payload: incorrect arithmetics when fetching VLAN header bits
+
+  * Jammy update: v5.15.85 upstream stable release (LP: #2003139)
+    - udf: Discard preallocation before extending file with a hole
+    - udf: Fix preallocation discarding at indirect extent boundary
+    - udf: Do not bother looking for prealloc extents if i_lenExtents matches
+      i_size
+    - udf: Fix extending file within last block
+    - usb: gadget: uvc: Prevent buffer overflow in setup handler
+    - USB: serial: option: add Quectel EM05-G modem
+    - USB: serial: cp210x: add Kamstrup RF sniffer PIDs
+    - USB: serial: f81232: fix division by zero on line-speed change
+    - USB: serial: f81534: fix division by zero on line-speed change
+    - xhci: Apply XHCI_RESET_TO_DEFAULT quirk to ADL-N
+    - igb: Initialize mailbox message for VF reset
+    - usb: dwc3: pci: Update PCIe device ID for USB3 controller on CPU sub-system
+      for Raptor Lake
+    - HID: uclogic: Add HID_QUIRK_HIDINPUT_FORCE quirk
+    - selftests: net: Use "grep -E" instead of "egrep"
+    - net: loopback: use NET_NAME_PREDICTABLE for name_assign_type
+    - Linux 5.15.85
+
+  * Jammy update: v5.15.84 upstream stable release (LP: #2003137)
+    - x86/vdso: Conditionally export __vdso_sgx_enter_enclave()
+    - vfs: fix copy_file_range() averts filesystem freeze protection
+    - ASoC: fsl_micfil: explicitly clear software reset bit
+    - ASoC: fsl_micfil: explicitly clear CHnF flags
+    - ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()
+    - libbpf: Use page size as max_entries when probing ring buffer map
+    - pinctrl: meditatek: Startup with the IRQs disabled
+    - can: sja1000: fix size of OCR_MODE_MASK define
+    - can: mcba_usb: Fix termination command argument
+    - net: fec: don't reset irq coalesce settings to defaults on "ip link up"
+    - ASoC: cs42l51: Correct PGA Volume minimum value
+    - perf: Fix perf_pending_task() UaF
+    - nvme-pci: clear the prp2 field when not used
+    - ASoC: ops: Correct bounds check for second channel on SX controls
+    - net: fec: properly guard irq coalesce setup
+    - Linux 5.15.84
+
+  * Jammy update: v5.15.83 upstream stable release (LP: #2003134)
+    - clk: generalize devm_clk_get() a bit
+    - clk: Provide new devm_clk helpers for prepared and enabled clocks
+    - mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()
+    - arm64: dts: rockchip: keep I2S1 disabled for GPIO function on ROCK Pi 4
+      series
+    - arm: dts: rockchip: fix node name for hym8563 rtc
+    - arm: dts: rockchip: remove clock-frequency from rtc
+    - ARM: dts: rockchip: fix ir-receiver node names
+    - arm64: dts: rockchip: fix ir-receiver node names
+    - ARM: dts: rockchip: rk3188: fix lcdc1-rgb24 node name
+    - fs: use acquire ordering in __fget_light()
+    - ARM: 9251/1: perf: Fix stacktraces for tracepoint events in THUMB2 kernels
+    - ARM: 9266/1: mm: fix no-MMU ZERO_PAGE() implementation
+    - ASoC: wm8962: Wait for updated value of WM8962_CLOCKING1 register
+    - spi: mediatek: Fix DEVAPC Violation at KO Remove
+    - ARM: dts: rockchip: disable arm_global_timer on rk3066 and rk3188
+    - ASoC: rt711-sdca: fix the latency time of clock stop prepare state machine
+      transitions
+    - 9p/fd: Use P9_HDRSZ for header size
+    - regulator: slg51000: Wait after asserting CS pin
+    - ALSA: seq: Fix function prototype mismatch in snd_seq_expand_var_event
+    - selftests/net: Find nettest in current directory
+    - btrfs: send: avoid unaligned encoded writes when attempting to clone range
+    - ASoC: soc-pcm: Add NULL check in BE reparenting
+    - regulator: twl6030: fix get status of twl6032 regulators
+    - fbcon: Use kzalloc() in fbcon_prepare_logo()
+    - usb: dwc3: gadget: Disable GUSB2PHYCFG.SUSPHY for End Transfer
+    - 9p/xen: check logical size for buffer size
+    - net: usb: qmi_wwan: add u-blox 0x1342 composition
+    - mm/khugepaged: take the right locks for page table retraction
+    - mm/khugepaged: fix GUP-fast interaction by sending IPI
+    - mm/khugepaged: invoke MMU notifiers in shmem/file collapse paths
+    - rtc: mc146818-lib: extract mc146818_avoid_UIP
+    - rtc: cmos: avoid UIP when writing alarm time
+    - rtc: cmos: avoid UIP when reading alarm time
+    - cifs: fix use-after-free caused by invalid pointer `hostname`
+    - drm/bridge: anx7625: Fix edid_read break case in sp_tx_edid_read()
+    - xen/netback: do some code cleanup
+    - xen/netback: don't call kfree_skb() with interrupts disabled
+    - media: videobuf2-core: take mmap_lock in vb2_get_unmapped_area()
+    - soundwire: intel: Initialize clock stop timeout
+    - media: v4l2-dv-timings.c: fix too strict blanking sanity checks
+    - memcg: fix possible use-after-free in memcg_write_event_control()
+    - mm/gup: fix gup_pud_range() for dax
+    - Bluetooth: btusb: Add debug message for CSR controllers
+    - Bluetooth: Fix crash when replugging CSR fake controllers
+    - net: mana: Fix race on per-CQ variable napi work_done
+    - KVM: s390: vsie: Fix the initialization of the epoch extension (epdx) field
+    - drm/vmwgfx: Don't use screen objects when SEV is active
+    - drm/amdgpu/sdma_v4_0: turn off SDMA ring buffer in the s2idle suspend
+    - drm/shmem-helper: Remove errant put in error path
+    - drm/shmem-helper: Avoid vm_open error paths
+    - net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
+    - HID: usbhid: Add ALWAYS_POLL quirk for some mice
+    - HID: hid-lg4ff: Add check for empty lbuf
+    - HID: core: fix shift-out-of-bounds in hid_report_raw_event
+    - HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10
+    - can: af_can: fix NULL pointer dereference in can_rcv_filter
+    - clk: Fix pointer casting to prevent oops in devm_clk_release()
+    - gpiolib: improve coding style for local variables
+    - gpiolib: check the 'ngpios' property in core gpiolib code
+    - gpiolib: fix memory leak in gpiochip_setup_dev()
+    - netfilter: nft_set_pipapo: Actually validate intervals in fields after the
+      first one
+    - drm/vmwgfx: Fix race issue calling pin_user_pages
+    - ieee802154: cc2520: Fix error return code in cc2520_hw_init()
+    - ca8210: Fix crash by zero initializing data
+    - netfilter: ctnetlink: fix compilation warning after data race fixes in ct
+      mark
+    - drm/bridge: ti-sn65dsi86: Fix output polarity setting bug
+    - gpio: amd8111: Fix PCI device reference count leak
+    - e1000e: Fix TX dispatch condition
+    - igb: Allocate MSI-X vector when testing
+    - net: broadcom: Add PTP_1588_CLOCK_OPTIONAL dependency for BCMGENET under
+      ARCH_BCM2835
+    - drm: bridge: dw_hdmi: fix preference of RGB modes over YUV420
+    - af_unix: Get user_ns from in_skb in unix_diag_get_exact().
+    - vmxnet3: correctly report encapsulated LRO packet
+    - vmxnet3: use correct intrConf reference when using extended queues
+    - Bluetooth: 6LoWPAN: add missing hci_dev_put() in get_l2cap_conn()
+    - Bluetooth: Fix not cleanup led when bt_init fails
+    - net: dsa: ksz: Check return value
+    - net: dsa: hellcreek: Check return value
+    - net: dsa: sja1105: Check return value
+    - selftests: rtnetlink: correct xfrm policy rule in kci_test_ipsec_offload
+    - mac802154: fix missing INIT_LIST_HEAD in ieee802154_if_add()
+    - net: encx24j600: Add parentheses to fix precedence
+    - net: encx24j600: Fix invalid logic in reading of MISTAT register
+    - net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
+    - net: mdiobus: fix double put fwnode in the error path
+    - octeontx2-pf: Fix potential memory leak in otx2_init_tc()
+    - xen-netfront: Fix NULL sring after live migration
+    - net: mvneta: Prevent out of bounds read in mvneta_config_rss()
+    - i40e: Fix not setting default xps_cpus after reset
+    - i40e: Fix for VF MAC address 0
+    - i40e: Disallow ip4 and ip6 l4_4_bytes
+    - NFC: nci: Bounds check struct nfc_target arrays
+    - nvme initialize core quirks before calling nvme_init_subsystem
+    - gpio/rockchip: fix refcount leak in rockchip_gpiolib_register()
+    - net: stmmac: fix "snps,axi-config" node property parsing
+    - ip_gre: do not report erspan version on GRE interface
+    - net: microchip: sparx5: Fix missing destroy_workqueue of mact_queue
+    - net: thunderx: Fix missing destroy_workqueue of nicvf_rx_mode_wq
+    - net: hisilicon: Fix potential use-after-free in hisi_femac_rx()
+    - net: mdio: fix unbalanced fwnode reference count in mdio_device_release()
+    - net: hisilicon: Fix potential use-after-free in hix5hd2_rx()
+    - tipc: Fix potential OOB in tipc_link_proto_rcv()
+    - ipv4: Fix incorrect route flushing when source address is deleted
+    - ipv4: Fix incorrect route flushing when table ID 0 is used
+    - net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()
+    - tipc: call tipc_lxc_xmit without holding node_read_lock
+    - ethernet: aeroflex: fix potential skb leak in greth_init_rings()
+    - dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and
+      dpaa2_switch_acl_entry_remove()
+    - net: phy: mxl-gpy: fix version reporting
+    - net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
+    - ipv6: avoid use-after-free in ip6_fragment()
+    - net: thunderbolt: fix memory leak in tbnet_open()
+    - net: mvneta: Fix an out of bounds check
+    - macsec: add missing attribute validation for offload
+    - s390/qeth: fix various format strings
+    - s390/qeth: fix use-after-free in hsci
+    - can: esd_usb: Allow REC and TEC to return to zero
+    - block: move CONFIG_BLOCK guard to top Makefile
+    - io_uring: move to separate directory
+    - io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()
+    - Linux 5.15.83
+
+  * 5.15.0-58.64 breaks xen bridge networking (pvh domU) (LP: #2002889) // Jammy
+    update: v5.15.83 upstream stable release (LP: #2003134)
+    - xen/netback: fix build warning
+
+  * Jammy update: v5.15.82 upstream stable release (LP: #2003132)
+    - arm64: mte: Avoid setting PG_mte_tagged if no tags cleared or restored
+    - drm/i915: Create a dummy object for gen6 ppgtt
+    - drm/i915/gt: Use i915_vm_put on ppgtt_create error paths
+    - erofs: fix order >= MAX_ORDER warning due to crafted negative i_size
+    - btrfs: sink iterator parameter to btrfs_ioctl_logical_to_ino
+    - btrfs: free btrfs_path before copying inodes to userspace
+    - spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock
+    - btrfs: move QUOTA_ENABLED check to rescan_should_stop from
+      btrfs_qgroup_rescan_worker
+    - btrfs: qgroup: fix sleep from invalid context bug in btrfs_qgroup_inherit()
+    - drm/display/dp_mst: Fix drm_dp_mst_add_affected_dsc_crtcs() return code
+    - drm/amdgpu: update drm_display_info correctly when the edid is read
+    - drm/amdgpu: Partially revert "drm/amdgpu: update drm_display_info correctly
+      when the edid is read"
+    - iio: health: afe4403: Fix oob read in afe4403_read_raw
+    - iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw
+    - iio: light: rpr0521: add missing Kconfig dependencies
+    - bpf, perf: Use subprog name when reporting subprog ksymbol
+    - scripts/faddr2line: Fix regression in name resolution on ppc64le
+    - ARM: at91: rm9200: fix usb device clock id
+    - libbpf: Handle size overflow for ringbuf mmap
+    - hwmon: (ltc2947) fix temperature scaling
+    - hwmon: (ina3221) Fix shunt sum critical calculation
+    - hwmon: (i5500_temp) fix missing pci_disable_device()
+    - hwmon: (ibmpex) Fix possible UAF when ibmpex_register_bmc() fails
+    - bpf: Do not copy spin lock field from user in bpf_selem_alloc
+    - nvmem: rmem: Fix return value check in rmem_read()
+    - of: property: decrement node refcount in of_fwnode_get_reference_args()
+    - ixgbevf: Fix resource leak in ixgbevf_init_module()
+    - i40e: Fix error handling in i40e_init_module()
+    - fm10k: Fix error handling in fm10k_init_module()
+    - iavf: remove redundant ret variable
+    - iavf: Fix error handling in iavf_init_module()
+    - e100: Fix possible use after free in e100_xmit_prepare
+    - net/mlx5: DR, Fix uninitialized var warning
+    - net/mlx5: Fix uninitialized variable bug in outlen_write()
+    - net/mlx5e: Fix use-after-free when reverting termination table
+    - can: sja1000_isa: sja1000_isa_probe(): add missing free_sja1000dev()
+    - can: cc770: cc770_isa_probe(): add missing free_cc770dev()
+    - can: etas_es58x: es58x_init_netdev(): free netdev when register_candev()
+    - can: m_can: pci: add missing m_can_class_free_dev() in probe/remove methods
+    - can: m_can: Add check for devm_clk_get
+    - qlcnic: fix sleep-in-atomic-context bugs caused by msleep
+    - aquantia: Do not purge addresses when setting the number of rings
+    - wifi: cfg80211: fix buffer overflow in elem comparison
+    - wifi: cfg80211: don't allow multi-BSSID in S1G
+    - wifi: mac8021: fix possible oob access in ieee80211_get_rate_duration
+    - net: phy: fix null-ptr-deref while probe() failed
+    - net: ethernet: ti: am65-cpsw: fix error handling in am65_cpsw_nuss_probe()
+    - net: net_netdev: Fix error handling in ntb_netdev_init_module()
+    - net/9p: Fix a potential socket leak in p9_socket_open
+    - net: ethernet: nixge: fix NULL dereference
+    - net: wwan: iosm: fix kernel test robot reported error
+    - net: wwan: iosm: fix dma_alloc_coherent incompatible pointer type
+    - dsa: lan9303: Correct stat name
+    - tipc: re-fetch skb cb after tipc_msg_validate
+    - net: hsr: Fix potential use-after-free
+    - net: mdiobus: fix unbalanced node reference count
+    - afs: Fix fileserver probe RTT handling
+    - net: tun: Fix use-after-free in tun_detach()
+    - packet: do not set TP_STATUS_CSUM_VALID on CHECKSUM_COMPLETE
+    - sctp: fix memory leak in sctp_stream_outq_migrate()
+    - net: ethernet: renesas: ravb: Fix promiscuous mode after system resumed
+    - hwmon: (coretemp) Check for null before removing sysfs attrs
+    - hwmon: (coretemp) fix pci device refcount leak in nv1a_ram_new()
+    - riscv: vdso: fix section overlapping under some conditions
+    - riscv: mm: Proper page permissions after initmem free
+    - ALSA: dice: fix regression for Lexicon I-ONIX FW810S
+    - error-injection: Add prompt for function error injection
+    - tools/vm/slabinfo-gnuplot: use "grep -E" instead of "egrep"
+    - nilfs2: fix NULL pointer dereference in nilfs_palloc_commit_free_entry()
+    - x86/bugs: Make sure MSR_SPEC_CTRL is updated properly upon resume from S3
+    - pinctrl: intel: Save and restore pins in "direct IRQ" mode
+    - v4l2: don't fall back to follow_pfn() if pin_user_pages_fast() fails
+    - net: stmmac: Set MAC's flow control register to reflect current settings
+    - mmc: mmc_test: Fix removal of debugfs file
+    - mmc: core: Fix ambiguous TRIM and DISCARD arg
+    - mmc: sdhci-esdhc-imx: correct CQHCI exit halt state check
+    - mmc: sdhci-sprd: Fix no reset data and command after voltage switch
+    - mmc: sdhci: Fix voltage switch delay
+    - drm/amdgpu: temporarily disable broken Clang builds due to blown stack-frame
+    - drm/amdgpu: enable Vangogh VCN indirect sram mode
+    - drm/i915: Fix negative value passed as remaining time
+    - drm/i915: Never return 0 if not all requests retired
+    - tracing/osnoise: Fix duration type
+    - tracing: Fix race where histograms can be called before the event
+    - tracing: Free buffers when a used dynamic event is removed
+    - io_uring: update res mask in io_poll_check_events
+    - io_uring: fix tw losing poll events
+    - io_uring: cmpxchg for poll arm refs release
+    - io_uring: make poll refs more robust
+    - io_uring/poll: fix poll_refs race with cancelation
+    - KVM: x86/mmu: Fix race condition in direct_page_fault
+    - ASoC: ops: Fix bounds check for _sx controls
+    - pinctrl: single: Fix potential division by zero
+    - riscv: Sync efi page table's kernel mappings before switching
+    - riscv: fix race when vmap stack overflow
+    - riscv: kexec: Fixup irq controller broken in kexec crash path
+    - nvme: fix SRCU protection of nvme_ns_head list
+    - iommu/vt-d: Fix PCI device refcount leak in has_external_pci()
+    - iommu/vt-d: Fix PCI device refcount leak in dmar_dev_scope_init()
+    - mm: __isolate_lru_page_prepare() in isolate_migratepages_block()
+    - mm: migrate: fix THP's mapcount on isolation
+    - parisc: Increase FRAME_WARN to 2048 bytes on parisc
+    - Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is
+      enabled
+    - selftests: net: add delete nexthop route warning test
+    - selftests: net: fix nexthop warning cleanup double ip typo
+    - ipv4: Handle attempt to delete multipath route when fib_info contains an nh
+      reference
+    - ipv4: Fix route deletion when nexthop info is not specified
+    - serial: stm32: Factor out GPIO RTS toggling into separate function
+    - serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode
+    - serial: stm32: Deassert Transmit Enable on ->rs485_config()
+    - i2c: npcm7xx: Fix error handling in npcm_i2c_init()
+    - i2c: imx: Only DMA messages with I2C_M_DMA_SAFE flag set
+    - ACPI: HMAT: remove unnecessary variable initialization
+    - ACPI: HMAT: Fix initiator registration for single-initiator systems
+    - Revert "clocksource/drivers/riscv: Events are stopped during CPU suspend"
+    - char: tpm: Protect tpm_pm_suspend with locks
+    - Input: raydium_ts_i2c - fix memory leak in raydium_i2c_send()
+    - ipc/sem: Fix dangling sem_array access in semtimedop race
+    - Linux 5.15.82
+
+  * Jammy update: v5.15.81 upstream stable release (LP: #2003130)
+    - ASoC: fsl_sai: use local device pointer
+    - ASoC: fsl_asrc fsl_esai fsl_sai: allow CONFIG_PM=N
+    - serial: Add rs485_supported to uart_port
+    - serial: fsl_lpuart: Fill in rs485_supported
+    - tty: serial: fsl_lpuart: don't break the on-going transfer when global reset
+    - sctp: remove the unnecessary sinfo_stream check in sctp_prsctp_prune_unsent
+    - sctp: clear out_curr if all frag chunks of current msg are pruned
+    - cifs: introduce new helper for cifs_reconnect()
+    - cifs: split out dfs code from cifs_reconnect()
+    - cifs: support nested dfs links over reconnect
+    - cifs: Fix connections leak when tlink setup failed
+    - ata: libata-scsi: simplify __ata_scsi_queuecmd()
+    - ata: libata-core: do not issue non-internal commands once EH is pending
+    - drm/display: Don't assume dual mode adaptors support i2c sub-addressing
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro
+    - nvme-pci: disable namespace identifiers for the MAXIO MAP1001
+    - nvme-pci: disable write zeroes on various Kingston SSD
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000
+    - iio: ms5611: Simplify IO callback parameters
+    - iio: pressure: ms5611: fixed value compensation bug
+    - ceph: do not update snapshot context when there is no new snapshot
+    - ceph: avoid putting the realm twice when decoding snaps fails
+    - x86/sgx: Create utility to validate user provided offset and length
+    - x86/sgx: Add overflow check in sgx_validate_offset_length()
+    - binder: validate alloc->mm in ->mmap() handler
+    - ceph: Use kcalloc for allocating multiple elements
+    - ceph: fix NULL pointer dereference for req->r_session
+    - wifi: mac80211: fix memory free error when registering wiphy fail
+    - wifi: mac80211_hwsim: fix debugfs attribute ps with rc table support
+    - riscv: dts: sifive unleashed: Add PWM controlled LEDs
+    - audit: fix undefined behavior in bit shift for AUDIT_BIT
+    - wifi: airo: do not assign -1 to unsigned char
+    - wifi: mac80211: Fix ack frame idr leak when mesh has no route
+    - wifi: ath11k: Fix QCN9074 firmware boot on x86
+    - spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
+    - selftests/bpf: Add verifier test for release_reference()
+    - Revert "net: macsec: report real_dev features when HW offloading is enabled"
+    - platform/x86: ideapad-laptop: Disable touchpad_switch
+    - platform/x86: touchscreen_dmi: Add info for the RCA Cambio W101 v2 2-in-1
+    - platform/x86/intel/pmt: Sapphire Rapids PMT errata fix
+    - platform/x86/intel/hid: Add some ACPI device IDs
+    - scsi: ibmvfc: Avoid path failures during live migration
+    - scsi: scsi_debug: Make the READ CAPACITY response compliant with ZBC
+    - drm: panel-orientation-quirks: Add quirk for Acer Switch V 10 (SW5-017)
+    - block, bfq: fix null pointer dereference in bfq_bio_bfqg()
+    - arm64/syscall: Include asm/ptrace.h in syscall_wrapper header.
+    - nvmet: fix memory leak in nvmet_subsys_attr_model_store_locked
+    - Revert "drm/amdgpu: Revert "drm/amdgpu: getting fan speed pwm for vega10
+      properly""
+    - ALSA: usb-audio: add quirk to fix Hamedal C20 disconnect issue
+    - RISC-V: vdso: Do not add missing symbols to version section in linker script
+    - MIPS: pic32: treat port as signed integer
+    - xfrm: fix "disable_policy" on ipv4 early demux
+    - xfrm: replay: Fix ESN wrap around for GSO
+    - af_key: Fix send_acquire race with pfkey_register
+    - ARM: dts: am335x-pcm-953: Define fixed regulators in root node
+    - ASoC: hdac_hda: fix hda pcm buffer overflow issue
+    - ASoC: sgtl5000: Reset the CHIP_CLK_CTRL reg on remove
+    - ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()
+    - x86/hyperv: Restore VP assist page after cpu offlining/onlining
+    - scsi: storvsc: Fix handling of srb_status and capacity change events
+    - ASoC: max98373: Add checks for devm_kcalloc
+    - regulator: core: fix kobject release warning and memory leak in
+      regulator_register()
+    - spi: dw-dma: decrease reference count in dw_spi_dma_init_mfld()
+    - regulator: core: fix UAF in destroy_regulator()
+    - bus: sunxi-rsb: Remove the shutdown callback
+    - bus: sunxi-rsb: Support atomic transfers
+    - tee: optee: fix possible memory leak in optee_register_device()
+    - ARM: dts: at91: sam9g20ek: enable udc vbus gpio pinctrl
+    - selftests: mptcp: more stable simult_flows tests
+    - selftests: mptcp: fix mibit vs mbit mix up
+    - net: liquidio: simplify if expression
+    - rxrpc: Allow list of in-use local UDP endpoints to be viewed in /proc
+    - rxrpc: Use refcount_t rather than atomic_t
+    - rxrpc: Fix race between conn bundle lookup and bundle removal [ZDI-
+      CAN-15975]
+    - net: dsa: sja1105: disallow C45 transactions on the BASE-TX MDIO bus
+    - nfc/nci: fix race with opening and closing
+    - net: pch_gbe: fix potential memleak in pch_gbe_tx_queue()
+    - 9p/fd: fix issue of list_del corruption in p9_fd_cancel()
+    - netfilter: conntrack: Fix data-races around ct mark
+    - netfilter: nf_tables: do not set up extensions for end interval
+    - iavf: Fix a crash during reset task
+    - iavf: Do not restart Tx queues after reset task failure
+    - iavf: Fix race condition between iavf_shutdown and iavf_remove
+    - ARM: mxs: fix memory leak in mxs_machine_init()
+    - ARM: dts: imx6q-prti6q: Fix ref/tcxo-clock-frequency properties
+    - net: ethernet: mtk_eth_soc: fix error handling in mtk_open()
+    - net/mlx4: Check retval of mlx4_bitmap_init
+    - net: mvpp2: fix possible invalid pointer dereference
+    - net/qla3xxx: fix potential memleak in ql3xxx_send()
+    - octeontx2-af: debugsfs: fix pci device refcount leak
+    - net: pch_gbe: fix pci device refcount leak while module exiting
+    - nfp: fill splittable of devlink_port_attrs correctly
+    - nfp: add port from netdev validation for EEPROM access
+    - macsec: Fix invalid error code set
+    - Drivers: hv: vmbus: fix double free in the error path of
+      vmbus_add_channel_work()
+    - Drivers: hv: vmbus: fix possible memory leak in vmbus_device_register()
+    - netfilter: ipset: regression in ip_set_hash_ip.c
+    - net/mlx5: Do not query pci info while pci disabled
+    - net/mlx5: Fix FW tracer timestamp calculation
+    - net/mlx5: Fix handling of entry refcount when command is not issued to FW
+    - tipc: set con sock in tipc_conn_alloc
+    - tipc: add an extra conn_get in tipc_conn_alloc
+    - tipc: check skb_linearize() return value in tipc_disc_rcv()
+    - xfrm: Fix oops in __xfrm_state_delete()
+    - xfrm: Fix ignored return value in xfrm6_init()
+    - net: wwan: iosm: use ACPI_FREE() but not kfree() in ipc_pcie_read_bios_cfg()
+    - sfc: fix potential memleak in __ef100_hard_start_xmit()
+    - net: sparx5: fix error handling in sparx5_port_open()
+    - net: sched: allow act_ct to be built without NF_NAT
+    - NFC: nci: fix memory leak in nci_rx_data_packet()
+    - regulator: twl6030: re-add TWL6032_SUBCLASS
+    - bnx2x: fix pci device refcount leak in bnx2x_vf_is_pcie_pending()
+    - dma-buf: fix racing conflict of dma_heap_add()
+    - netfilter: ipset: restore allowing 64 clashing elements in hash:net,iface
+    - netfilter: flowtable_offload: add missing locking
+    - fs: do not update freeing inode i_io_list
+    - dccp/tcp: Reset saddr on failure after inet6?_hash_connect().
+    - ipv4: Fix error return code in fib_table_insert()
+    - arcnet: fix potential memory leak in com20020_probe()
+    - s390/dasd: fix no record found for raw_track_access
+    - nfc: st-nci: fix incorrect validating logic in EVT_TRANSACTION
+    - nfc: st-nci: fix memory leaks in EVT_TRANSACTION
+    - nfc: st-nci: fix incorrect sizing calculations in EVT_TRANSACTION
+    - net: enetc: manage ENETC_F_QBV in priv->active_offloads only when enabled
+    - net: enetc: cache accesses to &priv->si->hw
+    - net: enetc: preserve TX ring priority across reconfiguration
+    - octeontx2-pf: Add check for devm_kcalloc
+    - octeontx2-af: Fix reference count issue in rvu_sdp_init()
+    - net: thunderx: Fix the ACPI memory leak
+    - s390/crashdump: fix TOD programmable field size
+    - lib/vdso: use "grep -E" instead of "egrep"
+    - [Config] updateconfigs for CC_HAS_ASM_GOTO_TIED_OUTPUT
+    - init/Kconfig: fix CC_HAS_ASM_GOTO_TIED_OUTPUT test with dash
+    - nios2: add FORCE for vmlinuz.gz
+    - mmc: sdhci-brcmstb: Re-organize flags
+    - mmc: sdhci-brcmstb: Enable Clock Gating to save power
+    - mmc: sdhci-brcmstb: Fix SDHCI_RESET_ALL for CQHCI
+    - KVM: arm64: pkvm: Fixup boot mode to reflect that the kernel resumes from
+      EL1
+    - usb: dwc3: exynos: Fix remove() function
+    - usb: cdnsp: Fix issue with Clear Feature Halt Endpoint
+    - usb: cdnsp: fix issue with ZLP - added TD_SIZE = 1
+    - ext4: fix use-after-free in ext4_ext_shift_extents
+    - arm64: dts: rockchip: lower rk3399-puma-haikou SD controller clock frequency
+    - iio: light: apds9960: fix wrong register for gesture gain
+    - iio: core: Fix entry not deleted when iio_register_sw_trigger_type() fails
+    - bus: ixp4xx: Don't touch bit 7 on IXP42x
+    - usb: dwc3: gadget: conditionally remove requests
+    - usb: dwc3: gadget: Return -ESHUTDOWN on ep disable
+    - usb: dwc3: gadget: Clear ep descriptor last
+    - nilfs2: fix nilfs_sufile_mark_dirty() not set segment usage as dirty
+    - gcov: clang: fix the buffer overflow issue
+    - mm: vmscan: fix extreme overreclaim and swap floods
+    - KVM: x86: nSVM: leave nested mode on vCPU free
+    - KVM: x86: forcibly leave nested mode on vCPU reset
+    - KVM: x86: nSVM: harden svm_free_nested against freeing vmcb02 while still in
+      use
+    - KVM: x86: add kvm_leave_nested
+    - KVM: x86: remove exit_int_info warning in svm_handle_exit
+    - x86/tsx: Add a feature bit for TSX control MSR support
+    - x86/pm: Add enumeration check before spec MSRs save/restore setup
+    - x86/ioremap: Fix page aligned size calculation in __ioremap_caller()
+    - Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode
+    - ASoC: Intel: bytcht_es8316: Add quirk for the Nanote UMPC-01
+    - tools: iio: iio_generic_buffer: Fix read size
+    - serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
+    - Input: goodix - try resetting the controller when no config is set
+    - Input: soc_button_array - add use_low_level_irq module parameter
+    - Input: soc_button_array - add Acer Switch V 10 to dmi_use_low_level_irq[]
+    - Input: i8042 - apply probe defer to more ASUS ZenBook models
+    - ASoC: stm32: dfsdm: manage cb buffers cleanup
+    - xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too
+    - xen/platform-pci: add missing free_irq() in error path
+    - platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
+    - platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)
+    - drm/amdgpu: disable BACO support on more cards
+    - zonefs: fix zone report size in __zonefs_io_error()
+    - platform/x86: hp-wmi: Ignore Smart Experience App event
+    - platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some
+      Yoga laptops
+    - [Config] updateconfigs for INET_TABLE_PERTURB_ORDER
+    - tcp: configurable source port perturb table size
+    - net: usb: qmi_wwan: add Telit 0x103a composition
+    - scsi: iscsi: Fix possible memory leak when device_register() failed
+    - gpu: host1x: Avoid trying to use GART on Tegra20
+    - dm integrity: flush the journal on suspend
+    - dm integrity: clear the journal on suspend
+    - fuse: lock inode unconditionally in fuse_fallocate()
+    - wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_OPER_CHANNEL attribute
+    - wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_CHANNEL_LIST attribute
+    - wifi: wilc1000: validate number of channels
+    - genirq/msi: Shutdown managed interrupts with unsatifiable affinities
+    - genirq: Always limit the affinity to online CPUs
+    - irqchip/gic-v3: Always trust the managed affinity provided by the core code
+    - genirq: Take the proposed affinity at face value if force==true
+    - btrfs: free btrfs_path before copying root refs to userspace
+    - btrfs: free btrfs_path before copying fspath to userspace
+    - btrfs: free btrfs_path before copying subvol info to userspace
+    - btrfs: zoned: fix missing endianness conversion in sb_write_pointer
+    - btrfs: use kvcalloc in btrfs_get_dev_zone_info
+    - btrfs: sysfs: normalize the error handling branch in btrfs_init_sysfs()
+    - drm/amd/dc/dce120: Fix audio register mapping, stop triggering KASAN
+    - drm/amd/display: No display after resume from WB/CB
+    - drm/amdgpu: Enable Aldebaran devices to report CU Occupancy
+    - drm/amdgpu: always register an MMU notifier for userptr
+    - cifs: fix missed refcounting of ipc tcon
+    - Linux 5.15.81
+
+  * Jammy update: v5.15.80 upstream stable release (LP: #2003122)
+    - mm: hwpoison: refactor refcount check handling
+    - mm: hwpoison: handle non-anonymous THP correctly
+    - mm: shmem: don't truncate page if memory failure happens
+    - ASoC: wm5102: Revert "ASoC: wm5102: Fix PM disable depth imbalance in
+      wm5102_probe"
+    - ASoC: wm5110: Revert "ASoC: wm5110: Fix PM disable depth imbalance in
+      wm5110_probe"
+    - ASoC: wm8997: Revert "ASoC: wm8997: Fix PM disable depth imbalance in
+      wm8997_probe"
+    - ASoC: mt6660: Keep the pm_runtime enables before component stuff in
+      mt6660_i2c_probe
+    - ASoC: rt1019: Fix the TDM settings
+    - ASoC: wm8962: Add an event handler for TEMP_HP and TEMP_SPK
+    - spi: intel: Fix the offset to get the 64K erase opcode
+    - ASoC: codecs: jz4725b: add missed Line In power control bit
+    - ASoC: codecs: jz4725b: fix reported volume for Master ctl
+    - ASoC: codecs: jz4725b: use right control for Capture Volume
+    - ASoC: codecs: jz4725b: fix capture selector naming
+    - ASoC: Intel: sof_sdw: add quirk variant for LAPBC710 NUC15
+    - selftests/futex: fix build for clang
+    - selftests/intel_pstate: fix build for ARCH=x86_64
+    - ASoC: rt1308-sdw: add the default value of some registers
+    - drm/amd/display: Remove wrong pipe control lock
+    - ACPI: scan: Add LATT2021 to acpi_ignore_dep_ids[]
+    - RDMA/efa: Add EFA 0xefa2 PCI ID
+    - btrfs: raid56: properly handle the error when unable to find the missing
+      stripe
+    - NFSv4: Retry LOCK on OLD_STATEID during delegation return
+    - ACPI: x86: Add another system to quirk list for forcing StorageD3Enable
+    - firmware: arm_scmi: Cleanup the core driver removal callback
+    - i2c: tegra: Allocate DMA memory for DMA engine
+    - i2c: i801: add lis3lv02d's I2C address for Vostro 5568
+    - drm/imx: imx-tve: Fix return type of imx_tve_connector_mode_valid
+    - btrfs: remove pointless and double ulist frees in error paths of qgroup
+      tests
+    - x86/cpu: Add several Intel server CPU model numbers
+    - ASoC: codecs: jz4725b: Fix spelling mistake "Sourc" -> "Source", "Routee" ->
+      "Route"
+    - mtd: spi-nor: intel-spi: Disable write protection only if asked
+    - spi: intel: Use correct mask for flash and protected regions
+    - KVM: x86/pmu: Do not speculatively query Intel GP PMCs that don't exist yet
+    - hugetlbfs: don't delete error page from pagecache
+    - arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8150-xperia-kumano: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8250-xperia-edo: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8350-hdk: Specify which LDO modes are allowed
+    - spi: stm32: Print summary 'callbacks suppressed' message
+    - ARM: dts: at91: sama7g5: fix signal name of pin PB2
+    - ASoC: core: Fix use-after-free in snd_soc_exit()
+    - ASoC: tas2770: Fix set_tdm_slot in case of single slot
+    - ASoC: tas2764: Fix set_tdm_slot in case of single slot
+    - ARM: at91: pm: avoid soft resetting AC DLL
+    - serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl()
+    - serial: 8250_omap: remove wait loop from Errata i202 workaround
+    - serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()
+    - serial: 8250: omap: Flush PM QOS work on remove
+    - serial: imx: Add missing .thaw_noirq hook
+    - tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send
+    - bpf, test_run: Fix alignment problem in bpf_prog_test_run_skb()
+    - ASoC: soc-utils: Remove __exit for snd_soc_util_exit()
+    - pinctrl: rockchip: list all pins in a possible mux route for PX30
+    - scsi: scsi_transport_sas: Fix error handling in sas_phy_add()
+    - block: sed-opal: kmalloc the cmd/resp buffers
+    - bpf: Fix memory leaks in __check_func_call
+    - arm64: Fix bit-shifting UB in the MIDR_CPU_MODEL() macro
+    - siox: fix possible memory leak in siox_device_add()
+    - parport_pc: Avoid FIFO port location truncation
+    - pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
+    - drm/vc4: kms: Fix IS_ERR() vs NULL check for vc4_kms
+    - drm/panel: simple: set bpc field for logic technologies displays
+    - drm/drv: Fix potential memory leak in drm_dev_init()
+    - drm: Fix potential null-ptr-deref in drm_vblank_destroy_worker()
+    - arm64: dts: imx8mm: Fix NAND controller size-cells
+    - arm64: dts: imx8mn: Fix NAND controller size-cells
+    - ata: libata-transport: fix double ata_host_put() in ata_tport_add()
+    - ata: libata-transport: fix error handling in ata_tport_add()
+    - ata: libata-transport: fix error handling in ata_tlink_add()
+    - ata: libata-transport: fix error handling in ata_tdev_add()
+    - nfp: change eeprom length to max length enumerators
+    - MIPS: fix duplicate definitions for exported symbols
+    - MIPS: Loongson64: Add WARN_ON on kexec related kmalloc failed
+    - bpf: Initialize same number of free nodes for each pcpu_freelist
+    - net: bgmac: Drop free_netdev() from bgmac_enet_remove()
+    - mISDN: fix possible memory leak in mISDN_dsp_element_register()
+    - net: hinic: Fix error handling in hinic_module_init()
+    - net: stmmac: ensure tx function is not running in stmmac_xdp_release()
+    - soc: imx8m: Enable OCOTP clock before reading the register
+    - net: liquidio: release resources when liquidio driver open failed
+    - mISDN: fix misuse of put_device() in mISDN_register_device()
+    - net: macvlan: Use built-in RCU list checking
+    - net: caif: fix double disconnect client in chnl_net_open()
+    - bnxt_en: Remove debugfs when pci_register_driver failed
+    - net: mhi: Fix memory leak in mhi_net_dellink()
+    - net: dsa: make dsa_master_ioctl() see through port_hwtstamp_get() shims
+    - xen/pcpu: fix possible memory leak in register_pcpu()
+    - net: ionic: Fix error handling in ionic_init_module()
+    - net: ena: Fix error handling in ena_init()
+    - net: hns3: fix setting incorrect phy link ksettings for firmware in
+      resetting process
+    - bridge: switchdev: Fix memory leaks when changing VLAN protocol
+    - drbd: use after free in drbd_create_device()
+    - platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when
+      virtualized
+    - platform/surface: aggregator: Do not check for repeated unsequenced packets
+    - cifs: add check for returning value of SMB2_close_init
+    - net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in
+      ag71xx_open()
+    - net/x25: Fix skb leak in x25_lapb_receive_frame()
+    - cifs: Fix wrong return value checking when GETFLAGS
+    - net: microchip: sparx5: Fix potential null-ptr-deref in sparx_stats_init()
+      and sparx5_start()
+    - net: thunderbolt: Fix error handling in tbnet_init()
+    - cifs: add check for returning value of SMB2_set_info_init
+    - ftrace: Fix the possible incorrect kernel message
+    - ftrace: Optimize the allocation for mcount entries
+    - ftrace: Fix null pointer dereference in ftrace_add_mod()
+    - ring_buffer: Do not deactivate non-existant pages
+    - tracing: Fix memory leak in tracing_read_pipe()
+    - tracing/ring-buffer: Have polling block on watermark
+    - tracing: Fix memory leak in test_gen_synth_cmd() and
+      test_empty_synth_event()
+    - tracing: Fix wild-memory-access in register_synth_event()
+    - tracing: Fix race where eprobes can be called before the event
+    - tracing: kprobe: Fix potential null-ptr-deref on trace_event_file in
+      kprobe_event_gen_test_exit()
+    - tracing: kprobe: Fix potential null-ptr-deref on trace_array in
+      kprobe_event_gen_test_exit()
+    - drm/amd/display: Add HUBP surface flip interrupt handler
+    - ALSA: usb-audio: Drop snd_BUG_ON() from snd_usbmidi_output_open()
+    - ALSA: hda/realtek: fix speakers for Samsung Galaxy Book Pro
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
+    - Revert "usb: dwc3: disable USB core PHY management"
+    - slimbus: qcom-ngd: Fix build error when CONFIG_SLIM_QCOM_NGD_CTRL=y &&
+      CONFIG_QCOM_RPROC_COMMON=m
+    - slimbus: stream: correct presence rate frequencies
+    - speakup: fix a segfault caused by switching consoles
+    - USB: bcma: Make GPIO explicitly optional
+    - USB: serial: option: add Sierra Wireless EM9191
+    - USB: serial: option: remove old LARA-R6 PID
+    - USB: serial: option: add u-blox LARA-R6 00B modem
+    - USB: serial: option: add u-blox LARA-L6 modem
+    - USB: serial: option: add Fibocom FM160 0x0111 composition
+    - usb: add NO_LPM quirk for Realforce 87U Keyboard
+    - usb: chipidea: fix deadlock in ci_otg_del_timer
+    - usb: cdns3: host: fix endless superspeed hub port reset
+    - usb: typec: mux: Enter safe mode only when pins need to be reconfigured
+    - iio: adc: at91_adc: fix possible memory leak in at91_adc_allocate_trigger()
+    - iio: trigger: sysfs: fix possible memory leak in iio_sysfs_trig_init()
+    - iio: adc: mp2629: fix wrong comparison of channel
+    - iio: adc: mp2629: fix potential array out of bound access
+    - iio: pressure: ms5611: changed hardcoded SPI speed to value limited
+    - dm ioctl: fix misbehavior if list_versions races with module loading
+    - serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs
+    - serial: 8250: Flush DMA Rx on RLSI
+    - serial: 8250_lpss: Configure DMA also w/o DMA filter
+    - Input: iforce - invert valid length check when fetching device IDs
+    - maccess: Fix writing offset in case of fault in
+      strncpy_from_kernel_nofault()
+    - net: phy: marvell: add sleep time after enabling the loopback bit
+    - scsi: zfcp: Fix double free of FSF request when qdio send fails
+    - iommu/vt-d: Preset Access bit for IOVA in FL non-leaf paging entries
+    - iommu/vt-d: Set SRE bit only when hardware has SRS cap
+    - firmware: coreboot: Register bus in module init
+    - mmc: core: properly select voltage range without power cycle
+    - mmc: sdhci-pci-o2micro: fix card detect fail issue caused by CD# debounce
+      timeout
+    - mmc: sdhci-pci: Fix possible memory leak caused by missing pci_dev_put()
+    - docs: update mediator contact information in CoC doc
+    - misc/vmw_vmci: fix an infoleak in vmci_host_do_receive_datagram()
+    - perf/x86/intel/pt: Fix sampling using single range output
+    - nvme: restrict management ioctls to admin
+    - nvme: ensure subsystem reset is single threaded
+    - serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake
+    - perf: Improve missing SIGTRAP checking
+    - ring-buffer: Include dropped pages in counting dirty patches
+    - tracing: Fix warning on variable 'struct trace_array'
+    - net: use struct_group to copy ip/ipv6 header addresses
+    - scsi: target: tcm_loop: Fix possible name leak in tcm_loop_setup_hba_bus()
+    - scsi: scsi_debug: Fix possible UAF in sdebug_add_host_helper()
+    - kprobes: Skip clearing aggrprobe's post_handler in kprobe-on-ftrace case
+    - Input: i8042 - fix leaking of platform device on module removal
+    - macvlan: enforce a consistent minimal mtu
+    - tcp: cdg: allow tcp_cdg_release() to be called multiple times
+    - kcm: avoid potential race in kcm_tx_work
+    - kcm: close race conditions on sk_receive_queue
+    - 9p: trans_fd/p9_conn_cancel: drop client lock earlier
+    - gfs2: Check sb_bsize_shift after reading superblock
+    - gfs2: Switch from strlcpy to strscpy
+    - 9p/trans_fd: always use O_NONBLOCK read/write
+    - wifi: wext: use flex array destination for memcpy()
+    - mm: fs: initialize fsdata passed to write_begin/write_end interface
+    - net/9p: use a dedicated spinlock for trans_fd
+    - ntfs: fix use-after-free in ntfs_attr_find()
+    - ntfs: fix out-of-bounds read in ntfs_attr_find()
+    - ntfs: check overflow when iterating ATTR_RECORDs
+    - Linux 5.15.80
+
+  * CVE-2022-4139
+    - drm/i915: fix TLB invalidation for Gen12 video and compute engines
+
+  * Jammy update: v5.15.79 upstream stable release (LP: #2001570)
+    - fuse: fix readdir cache race
+    - drm/amdkfd: avoid recursive lock in migrations back to RAM
+    - drm/amdkfd: handle CPU fault on COW mapping
+    - drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()
+    - hwspinlock: qcom: correct MMIO max register for newer SoCs
+    - phy: stm32: fix an error code in probe
+    - wifi: cfg80211: silence a sparse RCU warning
+    - wifi: cfg80211: fix memory leak in query_regdb_file()
+    - soundwire: qcom: reinit broadcast completion
+    - soundwire: qcom: check for outanding writes before doing a read
+    - bpf, verifier: Fix memory leak in array reallocation for stack state
+    - bpf, sockmap: Fix the sk->sk_forward_alloc warning of sk_stream_kill_queues
+    - wifi: mac80211: Set TWT Information Frame Disabled bit as 1
+    - bpftool: Fix NULL pointer dereference when pin {PROG, MAP, LINK} without
+      FILE
+    - HID: hyperv: fix possible memory leak in mousevsc_probe()
+    - bpf, sockmap: Fix sk->sk_forward_alloc warn_on in sk_stream_kill_queues
+    - bpf: Fix sockmap calling sleepable function in teardown path
+    - bpf, sock_map: Move cancel_work_sync() out of sock lock
+    - bpf: Add helper macro bpf_for_each_reg_in_vstate
+    - bpf: Fix wrong reg type conversion in release_reference()
+    - net: gso: fix panic on frag_list with mixed head alloc types
+    - macsec: delete new rxsc when offload fails
+    - macsec: fix secy->n_rx_sc accounting
+    - macsec: fix detection of RXSCs when toggling offloading
+    - macsec: clear encryption keys from the stack after setting up offload
+    - octeontx2-pf: Use hardware register for CQE count
+    - octeontx2-pf: NIX TX overwrites SQ_CTX_HW_S[SQ_INT]
+    - net: tun: Fix memory leaks of napi_get_frags
+    - bnxt_en: Fix possible crash in bnxt_hwrm_set_coal()
+    - bnxt_en: fix potentially incorrect return value for ndo_rx_flow_steer
+    - net: fman: Unregister ethernet device on removal
+    - capabilities: fix undefined behavior in bit shift for CAP_TO_MASK
+    - phy: ralink: mt7621-pci: add sentinel to quirks table
+    - KVM: s390: pv: don't allow userspace to set the clock under PV
+    - net: lapbether: fix issue of dev reference count leakage in
+      lapbeth_device_event()
+    - hamradio: fix issue of dev reference count leakage in bpq_device_event()
+    - net: wwan: iosm: fix memory leak in ipc_wwan_dellink
+    - net: wwan: mhi: fix memory leak in mhi_mbim_dellink
+    - drm/vc4: Fix missing platform_unregister_drivers() call in
+      vc4_drm_register()
+    - tcp: prohibit TCP_REPAIR_OPTIONS if data was already sent
+    - ipv6: addrlabel: fix infoleak when sending struct ifaddrlblmsg to network
+    - can: af_can: fix NULL pointer dereference in can_rx_register()
+    - net: stmmac: dwmac-meson8b: fix meson8b_devm_clk_prepare_enable()
+    - net: broadcom: Fix BCMGENET Kconfig
+    - tipc: fix the msg->req tlv len check in
+      tipc_nl_compat_name_table_dump_header
+    - dmaengine: pxa_dma: use platform_get_irq_optional
+    - dmaengine: mv_xor_v2: Fix a resource leak in mv_xor_v2_remove()
+    - dmaengine: ti: k3-udma-glue: fix memory leak when register device fail
+    - net: lapbether: fix issue of invalid opcode in lapbeth_open()
+    - drivers: net: xgene: disable napi when register irq failed in
+      xgene_enet_open()
+    - perf stat: Fix printing os->prefix in CSV metrics output
+    - perf tools: Add the include/perf/ directory to .gitignore
+    - netfilter: nfnetlink: fix potential dead lock in nfnetlink_rcv_msg()
+    - netfilter: Cleanup nft_net->module_list from nf_tables_exit_net()
+    - net: marvell: prestera: fix memory leak in prestera_rxtx_switch_init()
+    - net: nixge: disable napi when enable interrupts failed in nixge_open()
+    - net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg
+    - net/mlx5: Bridge, verify LAG state when adding bond to bridge
+    - net/mlx5: Allow async trigger completion execution on single CPU systems
+    - net/mlx5e: E-Switch, Fix comparing termination table instance
+    - net: cpsw: disable napi in cpsw_ndo_open()
+    - net: cxgb3_main: disable napi when bind qsets failed in cxgb_up()
+    - stmmac: intel: Enable 2.5Gbps for Intel AlderLake-S
+    - stmmac: intel: Update PCH PTP clock rate from 200MHz to 204.8MHz
+    - mctp: Fix an error handling path in mctp_init()
+    - cxgb4vf: shut down the adapter when t4vf_update_port_info() failed in
+      cxgb4vf_open()
+    - stmmac: dwmac-loongson: fix missing pci_disable_msi() while module exiting
+    - stmmac: dwmac-loongson: fix missing pci_disable_device() in
+      loongson_dwmac_probe()
+    - stmmac: dwmac-loongson: fix missing of_node_put() while module exiting
+    - net: phy: mscc: macsec: clear encryption keys when freeing a flow
+    - net: atlantic: macsec: clear encryption keys from the stack
+    - ethernet: s2io: disable napi when start nic failed in s2io_card_up()
+    - net: mv643xx_eth: disable napi when init rxq or txq failed in
+      mv643xx_eth_open()
+    - ethernet: tundra: free irq when alloc ring failed in tsi108_open()
+    - net: macvlan: fix memory leaks of macvlan_common_newlink
+    - riscv: process: fix kernel info leakage
+    - riscv: vdso: fix build with llvm
+    - riscv: fix reserved memory setup
+    - arm64: efi: Fix handling of misaligned runtime regions and drop warning
+    - MIPS: jump_label: Fix compat branch range check
+    - mmc: cqhci: Provide helper for resetting both SDHCI and CQHCI
+    - mmc: sdhci-of-arasan: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci_am654: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci-tegra: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci-esdhc-imx: use the correct host caps for MMC_CAP_8_BIT_DATA
+    - ALSA: hda/hdmi - enable runtime pm for more AMD display audio
+    - ALSA: hda/ca0132: add quirk for EVGA Z390 DARK
+    - ALSA: hda: fix potential memleak in 'add_widget_node'
+    - ALSA: hda/realtek: Add Positivo C6300 model quirk
+    - ALSA: usb-audio: Yet more regression for for the delayed card registration
+    - ALSA: usb-audio: Add quirk entry for M-Audio Micro
+    - ALSA: usb-audio: Add DSD support for Accuphase DAC-60
+    - vmlinux.lds.h: Fix placement of '.data..decrypted' section
+    - ata: libata-scsi: fix SYNCHRONIZE CACHE (16) command failure
+    - nilfs2: fix deadlock in nilfs_count_free_blocks()
+    - nilfs2: fix use-after-free bug of ns_writer on remount
+    - drm/i915/dmabuf: fix sg_table handling in map_dma_buf
+    - drm/amdgpu: disable BACO on special BEIGE_GOBY card
+    - btrfs: fix match incorrectly in dev_args_match_device
+    - btrfs: selftests: fix wrong error check in btrfs_free_dummy_root()
+    - btrfs: zoned: initialize device's zone info for seeding
+    - mms: sdhci-esdhc-imx: Fix SDHCI_RESET_ALL for CQHCI
+    - udf: Fix a slab-out-of-bounds write bug in udf_find_entry()
+    - mm/damon/dbgfs: check if rm_contexts input is for a real context
+    - mm/memremap.c: map FS_DAX device memory as decrypted
+    - mm/shmem: use page_mapping() to detect page cache for uffd continue
+    - can: j1939: j1939_send_one(): fix missing CAN header initialization
+    - cert host tools: Stop complaining about deprecated OpenSSL functions
+    - dmaengine: at_hdmac: Fix at_lli struct definition
+    - dmaengine: at_hdmac: Don't start transactions at tx_submit level
+    - dmaengine: at_hdmac: Start transfer for cyclic channels in issue_pending
+    - dmaengine: at_hdmac: Fix premature completion of desc in issue_pending
+    - dmaengine: at_hdmac: Do not call the complete callback on
+      device_terminate_all
+    - dmaengine: at_hdmac: Protect atchan->status with the channel lock
+    - dmaengine: at_hdmac: Fix concurrency problems by removing atc_complete_all()
+    - dmaengine: at_hdmac: Fix concurrency over descriptor
+    - dmaengine: at_hdmac: Free the memset buf without holding the chan lock
+    - dmaengine: at_hdmac: Fix concurrency over the active list
+    - dmaengine: at_hdmac: Fix descriptor handling when issuing it to hardware
+    - dmaengine: at_hdmac: Fix completion of unissued descriptor in case of errors
+    - dmaengine: at_hdmac: Don't allow CPU to reorder channel enable
+    - dmaengine: at_hdmac: Fix impossible condition
+    - dmaengine: at_hdmac: Check return code of dma_async_device_register
+    - marvell: octeontx2: build error: unknown type name 'u64'
+    - drm/amdkfd: Migrate in CPU page fault use current mm
+    - net: tun: call napi_schedule_prep() to ensure we own a napi
+    - x86/cpu: Restore AMD's DE_CFG MSR after resume
+    - Linux 5.15.79
+
+  * CVE-2022-47520
+    - wifi: wilc1000: validate pairwise and authentication suite offsets
+
+  * CVE-2022-3545
+    - nfp: fix use-after-free in area_cache_get()
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 01 Feb 2023 15:11:34 +0100
+
+linux (5.15.0-60.66) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-60.66 -proposed tracker (LP: #2003450)
+
+  * Revoke & rotate to new signing key (LP: #2002812)
+    - [Packaging] Revoke and rotate to new signing key
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 20 Jan 2023 14:42:28 +0100
+
+linux (5.15.0-59.65) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-59.65 -proposed tracker (LP: #2001801)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * CVE-2022-47940
+    - ksmbd: validate length in smb2_write()
+
+  * Fix iosm: WWAN cannot build the connection (DW5823e) (LP: #1998115)
+    - net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled
+    - [Config] CONFIG_IOSM update annotations on arm64 armhf ppc64el s390x
+
+  * support for same series backports versioning numbers (LP: #1993563)
+    - [Packaging] sameport -- add support for sameport versioning
+
+  * [DEP-8] Run ADT regression suite for lowlatency kernels Jammy and later
+    (LP: #1999528)
+    - [DEP-8] Fix regression suite to run on lowlatency
+
+  * Micron NVME storage failure [1344,5407] (LP: #1998883)
+    - nvme: add a bogus subsystem NQN quirk for Micron MTFDKBA2T0TFH
+
+  * Jammy update: v5.15.78 upstream stable release (LP: #1998843)
+    - scsi: lpfc: Rework MIB Rx Monitor debug info logic
+    - serial: ar933x: Deassert Transmit Enable on ->rs485_config()
+    - KVM: x86: Trace re-injected exceptions
+    - KVM: x86: Treat #DBs from the emulator as fault-like (code and DR7.GD=1)
+    - drm/amd/display: explicitly disable psr_feature_enable appropriately
+    - mm/hugetlb: fix races when looking up a CONT-PTE/PMD size hugetlb page
+    - HID: playstation: add initial DualSense Edge controller support
+    - KVM: x86: Protect the unused bits in MSR exiting flags
+    - KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
+    - KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
+    - RDMA/cma: Use output interface for net_dev check
+    - IB/hfi1: Correctly move list in sc_disable()
+    - RDMA/hns: Remove magic number
+    - RDMA/hns: Use hr_reg_xxx() instead of remaining roce_set_xxx()
+    - RDMA/hns: Disable local invalidate operation
+    - NFSv4: Fix a potential state reclaim deadlock
+    - NFSv4.1: Handle RECLAIM_COMPLETE trunking errors
+    - NFSv4.1: We must always send RECLAIM_COMPLETE after a reboot
+    - SUNRPC: Fix null-ptr-deref when xps sysfs alloc failed
+    - NFSv4.2: Fixup CLONE dest file size for zero-length count
+    - nfs4: Fix kmemleak when allocate slot failed
+    - net: dsa: Fix possible memory leaks in dsa_loop_init()
+    - RDMA/core: Fix null-ptr-deref in ib_core_cleanup()
+    - RDMA/qedr: clean up work queue on failure in qedr_alloc_resources()
+    - net: dsa: fall back to default tagger if we can't load the one from DT
+    - nfc: fdp: Fix potential memory leak in fdp_nci_send()
+    - nfc: nxp-nci: Fix potential memory leak in nxp_nci_send()
+    - nfc: s3fwrn5: Fix potential memory leak in s3fwrn5_nci_send()
+    - nfc: nfcmrvl: Fix potential memory leak in nfcmrvl_i2c_nci_send()
+    - net: fec: fix improper use of NETDEV_TX_BUSY
+    - ata: pata_legacy: fix pdc20230_set_piomode()
+    - net: sched: Fix use after free in red_enqueue()
+    - net: tun: fix bugs for oversize packet when napi frags enabled
+    - netfilter: nf_tables: netlink notifier might race to release objects
+    - netfilter: nf_tables: release flow rule object from commit path
+    - ipvs: use explicitly signed chars
+    - ipvs: fix WARNING in __ip_vs_cleanup_batch()
+    - ipvs: fix WARNING in ip_vs_app_net_cleanup()
+    - rose: Fix NULL pointer dereference in rose_send_frame()
+    - mISDN: fix possible memory leak in mISDN_register_device()
+    - isdn: mISDN: netjet: fix wrong check of device registration
+    - btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
+    - btrfs: fix inode list leak during backref walking at find_parent_nodes()
+    - btrfs: fix ulist leaks in error paths of qgroup self tests
+    - netfilter: ipset: enforce documented limit to prevent allocating huge memory
+    - Bluetooth: virtio_bt: Use skb_put to set length
+    - Bluetooth: L2CAP: fix use-after-free in l2cap_conn_del()
+    - Bluetooth: L2CAP: Fix memory leak in vhci_write
+    - net: mdio: fix undefined behavior in bit shift for __mdiobus_register
+    - ibmvnic: Free rwi on reset success
+    - stmmac: dwmac-loongson: fix invalid mdio_node
+    - net/smc: Fix possible leaked pernet namespace in smc_init()
+    - net, neigh: Fix null-ptr-deref in neigh_table_clear()
+    - ipv6: fix WARNING in ip6_route_net_exit_late()
+    - vsock: fix possible infinite sleep in vsock_connectible_wait_data()
+    - drm/msm/hdmi: Remove spurious IRQF_ONESHOT flag
+    - drm/msm/hdmi: fix IRQ lifetime
+    - video/fbdev/stifb: Implement the stifb_fillrect() function
+    - fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
+    - mtd: parsers: bcm47xxpart: print correct offset on read error
+    - mtd: parsers: bcm47xxpart: Fix halfblock reads
+    - s390/uaccess: add missing EX_TABLE entries to __clear_user()
+    - s390/cio: fix out-of-bounds access on cio_ignore free
+    - media: rkisp1: Don't pass the quantization to rkisp1_csm_config()
+    - media: rkisp1: Initialize color space on resizer sink and source pads
+    - media: rkisp1: Use correct macro for gradient registers
+    - media: rkisp1: Zero v4l2_subdev_format fields in when validating links
+    - media: s5p_cec: limit msg.len to CEC_MAX_MSG_SIZE
+    - media: cros-ec-cec: limit msg.len to CEC_MAX_MSG_SIZE
+    - media: dvb-frontends/drxk: initialize err to 0
+    - media: meson: vdec: fix possible refcount leak in vdec_probe()
+    - media: v4l: subdev: Fail graciously when getting try data for NULL state
+    - ACPI: APEI: Fix integer overflow in ghes_estatus_pool_init()
+    - scsi: core: Restrict legal sdev_state transitions via sysfs
+    - HID: saitek: add madcatz variant of MMO7 mouse device ID
+    - drm/amdgpu: set vm_update_mode=0 as default for Sienna Cichlid in SRIOV case
+    - i2c: xiic: Add platform module alias
+    - efi/tpm: Pass correct address to memblock_reserve
+    - clk: qcom: Update the force mem core bit for GPU clocks
+    - ARM: dts: imx6qdl-gw59{10,13}: fix user pushbutton GPIO offset
+    - arm64: dts: imx8: correct clock order
+    - arm64: dts: lx2160a: specify clock frequencies for the MDIO controllers
+    - arm64: dts: ls1088a: specify clock frequencies for the MDIO controllers
+    - arm64: dts: ls208xa: specify clock frequencies for the MDIO controllers
+    - block: Fix possible memory leak for rq_wb on add_disk failure
+    - firmware: arm_scmi: Suppress the driver's bind attributes
+    - firmware: arm_scmi: Make Rx chan_setup fail on memory errors
+    - firmware: arm_scmi: Fix devres allocation device in virtio transport
+    - arm64: dts: juno: Add thermal critical trip points
+    - i2c: piix4: Fix adapter not be removed in piix4_remove()
+    - Bluetooth: L2CAP: Fix attempting to access uninitialized memory
+    - block, bfq: protect 'bfqd->queued' by 'bfqd->lock'
+    - af_unix: Fix memory leaks of the whole sk due to OOB skb.
+    - fscrypt: stop using keyrings subsystem for fscrypt_master_key
+    - fscrypt: fix keyring memory leak on mount failure
+    - btrfs: fix lost file sync on direct IO write with nowait and dsync iocb
+    - btrfs: fix tree mod log mishandling of reallocated nodes
+    - btrfs: fix type of parameter generation in btrfs_get_dentry
+    - ftrace: Fix use-after-free for dynamic ftrace_ops
+    - tcp/udp: Make early_demux back namespacified.
+    - tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
+    - kprobe: reverse kp->flags when arm_kprobe failed
+    - ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()
+    - tools/nolibc/string: Fix memcmp() implementation
+    - tracing/histogram: Update document for KEYS_MAX size
+    - capabilities: fix potential memleak on error path from vfs_getxattr_alloc()
+    - fuse: add file_modified() to fallocate
+    - efi: random: reduce seed size to 32 bytes
+    - efi: random: Use 'ACPI reclaim' memory for random seed
+    - arm64: entry: avoid kprobe recursion
+    - perf/x86/intel: Fix pebs event constraints for ICL
+    - perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
+    - perf/x86/intel: Fix pebs event constraints for SPR
+    - parisc: Make 8250_gsc driver dependend on CONFIG_PARISC
+    - parisc: Export iosapic_serial_irq() symbol for serial port driver
+    - parisc: Avoid printing the hardware path twice
+    - ext4: fix warning in 'ext4_da_release_space'
+    - ext4: fix BUG_ON() when directory entry has invalid rec_len
+    - x86/syscall: Include asm/ptrace.h in syscall_wrapper header
+    - KVM: x86: Mask off reserved bits in CPUID.80000006H
+    - KVM: x86: Mask off reserved bits in CPUID.8000001AH
+    - KVM: x86: Mask off reserved bits in CPUID.80000008H
+    - KVM: x86: Mask off reserved bits in CPUID.80000001H
+    - KVM: x86: Mask off reserved bits in CPUID.8000001FH
+    - KVM: VMX: fully disable SGX if SECONDARY_EXEC_ENCLS_EXITING unavailable
+    - KVM: arm64: Fix bad dereference on MTE-enabled systems
+    - KVM: x86: emulator: em_sysexit should update ctxt->mode
+    - KVM: x86: emulator: introduce emulator_recalc_and_set_mode
+    - KVM: x86: emulator: update the emulation mode after rsm
+    - KVM: x86: emulator: update the emulation mode after CR0 write
+    - tee: Fix tee_shm_register() for kernel TEE drivers
+    - ext4,f2fs: fix readahead of verity data
+    - cifs: fix regression in very old smb1 mounts
+    - drm/rockchip: dsi: Clean up 'usage_mode' when failing to attach
+    - drm/rockchip: dsi: Force synchronous probe
+    - drm/i915/sdvo: Filter out invalid outputs more sensibly
+    - drm/i915/sdvo: Setup DDC fully before output init
+    - wifi: brcmfmac: Fix potential buffer overflow in brcmf_fweh_event_worker()
+    - Linux 5.15.78
+
+  * Fix AMD-PState driver for Genoa CPU (LP: #1998106)
+    - Documentation: amd-pstate: add tracer tool introduction
+    - Documentation: amd-pstate: grammar and sentence structure updates
+    - Documentation: amd-pstate: Add unit test introduction
+    - cpufreq: amd-pstate: cpufreq: amd-pstate: reset MSR_AMD_PERF_CTL register at
+      init
+    - cpufreq: amd-pstate: change amd-pstate driver to be built-in type
+    - cpufreq: amd-pstate: add amd-pstate driver parameter for mode selection
+    - Documentation: amd-pstate: add driver working mode introduction
+    - Documentation: add amd-pstate kernel command line options
+
+  * Mediatek WLAN RZ616(MT7922) SAR table control (LP: #1997200)
+    - mt76: mt7921: add .set_sar_specs support
+    - mt76: add 6 GHz band support in mt76_sar_freq_ranges
+    - mt76: mt7921: introduce ACPI SAR support
+    - mt76: connac: add support for limiting to maximum regulatory Tx power
+    - mt76: move sar utilities to mt76-core module
+    - mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in
+      mt7921_config
+    - mt76: mt7921: introduce ACPI SAR config in tx power
+    - wifi: mt76: mt7921: fix use after free in mt7921_acpi_read()
+
+  * [22.04/Jammy] Replace SAUCE AMD DP tunneling patch by upstream version
+    (LP: #1989944)
+    - Revert "UBUNTU: SAUCE: thunderbolt: Add DP out resource when DP tunnel is
+      discovered."
+    - thunderbolt: Add DP OUT resource when DP tunnel is discovered
+
+  * Jammy update: v5.15.77 upstream stable release (LP: #1997981)
+    - NFSv4: Fix free of uninitialized nfs4_label on referral lookup.
+    - NFSv4: Add an fattr allocation to _nfs4_discover_trunking()
+    - can: j1939: transport: j1939_session_skb_drop_old():
+      spin_unlock_irqrestore() before kfree_skb()
+    - can: kvaser_usb: Fix possible completions during init_completion
+    - ALSA: Use del_timer_sync() before freeing timer
+    - ALSA: usb-audio: Add quirks for M-Audio Fast Track C400/600
+    - ALSA: au88x0: use explicitly signed char
+    - ALSA: rme9652: use explicitly signed char
+    - USB: add RESET_RESUME quirk for NVIDIA Jetson devices in RCM
+    - usb: gadget: uvc: fix sg handling in error case
+    - usb: gadget: uvc: fix sg handling during video encode
+    - usb: dwc3: gadget: Stop processing more requests on IMI
+    - usb: dwc3: gadget: Don't set IMI for no_interrupt
+    - usb: bdc: change state when port disconnected
+    - usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96
+      controller
+    - mtd: rawnand: marvell: Use correct logic for nand-keep-config
+    - xhci: Add quirk to reset host back to default state at shutdown
+    - xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
+    - xhci: Remove device endpoints from bandwidth list when freeing the device
+    - tools: iio: iio_utils: fix digit calculation
+    - iio: light: tsl2583: Fix module unloading
+    - iio: temperature: ltc2983: allocate iio channels once
+    - iio: adxl372: Fix unsafe buffer attributes
+    - fbdev: smscufx: Fix several use-after-free bugs
+    - cpufreq: intel_pstate: Read all MSRs on the target CPU
+    - cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores
+    - fs/binfmt_elf: Fix memory leak in load_elf_binary()
+    - exec: Copy oldsighand->action under spin-lock
+    - mac802154: Fix LQI recording
+    - scsi: qla2xxx: Use transport-defined speed mask for supported_speeds
+    - drm/amdgpu: disallow gfxoff until GC IP blocks complete s2idle resume
+    - drm/msm/dsi: fix memory corruption with too many bridges
+    - drm/msm/hdmi: fix memory corruption with too many bridges
+    - drm/msm/dp: fix IRQ lifetime
+    - coresight: cti: Fix hang in cti_disable_hw()
+    - mmc: sdhci_am654: 'select', not 'depends' REGMAP_MMIO
+    - mmc: core: Fix kernel panic when remove non-standard SDIO card
+    - mmc: sdhci-pci-core: Disable ES for ASUS BIOS on Jasper Lake
+    - mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus
+    - counter: microchip-tcb-capture: Handle Signal1 read and Synapse
+    - kernfs: fix use-after-free in __kernfs_remove
+    - pinctrl: Ingenic: JZ4755 bug fixes
+    - ARC: mm: fix leakage of memory allocated for PTE
+    - perf auxtrace: Fix address filter symbol name match for modules
+    - s390/futex: add missing EX_TABLE entry to __futex_atomic_op()
+    - s390/pci: add missing EX_TABLE entries to
+      __pcistg_mio_inuser()/__pcilg_mio_inuser()
+    - Revert "scsi: lpfc: Resolve some cleanup issues following SLI path
+      refactoring"
+    - Revert "scsi: lpfc: Fix element offset in __lpfc_sli_release_iocbq_s4()"
+    - Revert "scsi: lpfc: Fix locking for lpfc_sli_iocbq_lookup()"
+    - Revert "scsi: lpfc: SLI path split: Refactor SCSI paths"
+    - Revert "scsi: lpfc: SLI path split: Refactor fast and slow paths to native
+      SLI4"
+    - Revert "scsi: lpfc: SLI path split: Refactor lpfc_iocbq"
+    - mmc: block: Remove error check of hw_reset on reset
+    - ethtool: eeprom: fix null-deref on genl_info in dump
+    - net: ieee802154: fix error return code in dgram_bind()
+    - media: v4l2: Fix v4l2_i2c_subdev_set_name function documentation
+    - media: atomisp: prevent integer overflow in sh_css_set_black_frame()
+    - drm/msm: Fix return type of mdp4_lvds_connector_mode_valid
+    - KVM: selftests: Fix number of pages for memory slot in
+      memslot_modification_stress_test
+    - ASoC: qcom: lpass-cpu: mark HDMI TX registers as volatile
+    - perf: Fix missing SIGTRAPs
+    - sched/core: Fix comparison in sched_group_cookie_match()
+    - arc: iounmap() arg is volatile
+    - mtd: rawnand: intel: Add missing of_node_put() in ebu_nand_probe()
+    - ASoC: qcom: lpass-cpu: Mark HDMI TX parity register as volatile
+    - ALSA: ac97: fix possible memory leak in snd_ac97_dev_register()
+    - perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
+    - tipc: fix a null-ptr-deref in tipc_topsrv_accept
+    - net: netsec: fix error handling in netsec_register_mdio()
+    - net: hinic: fix incorrect assignment issue in hinic_set_interrupt_cfg()
+    - net: hinic: fix memory leak when reading function table
+    - net: hinic: fix the issue of CMDQ memory leaks
+    - net: hinic: fix the issue of double release MBOX callback of VF
+    - net: macb: Specify PHY PM management done by MAC
+    - nfc: virtual_ncidev: Fix memory leak in virtual_nci_send()
+    - x86/unwind/orc: Fix unreliable stack dump with gcov
+    - amd-xgbe: fix the SFP compliance codes check for DAC cables
+    - amd-xgbe: add the bit rate quirk for Molex cables
+    - drm/i915/dp: Reset frl trained flag before restarting FRL training
+    - atlantic: fix deadlock at aq_nic_stop
+    - kcm: annotate data-races around kcm->rx_psock
+    - kcm: annotate data-races around kcm->rx_wait
+    - net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
+    - net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY
+    - tcp: minor optimization in tcp_add_backlog()
+    - tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
+    - tcp: fix indefinite deferral of RTO with SACK reneging
+    - net-memcg: avoid stalls when under memory pressure
+    - drm/amdkfd: Fix memory leak in kfd_mem_dmamap_userptr()
+    - can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error
+      path
+    - can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error
+      path
+    - PM: hibernate: Allow hybrid sleep to work with s2idle
+    - media: vivid: s_fbuf: add more sanity checks
+    - media: vivid: dev->bitmap_cap wasn't freed in all cases
+    - media: v4l2-dv-timings: add sanity checks for blanking values
+    - media: videodev2.h: V4L2_DV_BT_BLANKING_HEIGHT should check 'interlaced'
+    - media: vivid: set num_in/outputs to 0 if not supported
+    - perf vendor events power10: Fix hv-24x7 metric events
+    - ipv6: ensure sane device mtu in tunnels
+    - i40e: Fix ethtool rx-flow-hash setting for X722
+    - i40e: Fix VF hang when reset is triggered on another VF
+    - i40e: Fix flow-type by setting GL_HASH_INSET registers
+    - net: ksz884x: fix missing pci_disable_device() on error in pcidev_init()
+    - PM: domains: Fix handling of unavailable/disabled idle states
+    - perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
+    - net: fec: limit register access on i.MX6UL
+    - net: ethernet: ave: Fix MAC to be in charge of PHY PM
+    - ALSA: aoa: i2sbus: fix possible memory leak in i2sbus_add_dev()
+    - ALSA: aoa: Fix I2S device accounting
+    - openvswitch: switch from WARN to pr_warn
+    - net: ehea: fix possible memory leak in ehea_register_port()
+    - net: bcmsysport: Indicate MAC is in charge of PHY PM
+    - nh: fix scope used to find saddr when adding non gw nh
+    - net: broadcom: bcm4908enet: remove redundant variable bytes
+    - net: broadcom: bcm4908_enet: update TX stats after actual transmission
+    - netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir
+      failed
+    - net/mlx5e: Do not increment ESN when updating IPsec ESN state
+    - net/mlx5e: Extend SKB room check to include PTP-SQ
+    - net/mlx5: Fix possible use-after-free in async command interface
+    - net/mlx5: Print more info on pci error handlers
+    - net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
+    - net/mlx5: Fix crash during sync firmware reset
+    - net: do not sense pfmemalloc status in skb_append_pagefrags()
+    - kcm: do not sense pfmemalloc status in kcm_sendpage()
+    - net: enetc: survive memory pressure without crashing
+    - arm64: Add AMPERE1 to the Spectre-BHB affected list
+    - scsi: sd: Revert "scsi: sd: Remove a local variable"
+    - can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
+    - can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global
+      FIFO receive
+    - serial: core: move RS485 configuration tasks from drivers into core
+    - serial: Deassert Transmit Enable on probe in driver-specific way
+    - Linux 5.15.77
+
+  * RCU stalls (LP: #1991951)
+    - [Config] Harmonize RCU_CPU_STALL_TIMEOUT
+
+  * Jammy update: v5.15.76 upstream stable release (LP: #1997113)
+    - r8152: add PID for the Lenovo OneLink+ Dock
+    - arm64/mm: Consolidate TCR_EL1 fields
+    - usb: gadget: uvc: consistently use define for headerlen
+    - usb: gadget: uvc: use on returned header len in video_encode_isoc_sg
+    - usb: gadget: uvc: rework uvcg_queue_next_buffer to uvcg_complete_buffer
+    - usb: gadget: uvc: giveback vb2 buffer on req complete
+    - usb: gadget: uvc: improve sg exit condition
+    - [Config] updateconfigs for ARM64_ERRATUM_1742098
+    - arm64: errata: Remove AES hwcap for COMPAT tasks
+    - perf/x86/intel/pt: Relax address filter validation
+    - btrfs: enhance unsupported compat RO flags handling
+    - ocfs2: clear dinode links count in case of error
+    - ocfs2: fix BUG when iput after ocfs2_mknod fails
+    - selinux: enable use of both GFP_KERNEL and GFP_ATOMIC in convert_context()
+    - cpufreq: qcom: fix writes in read-only memory region
+    - i2c: qcom-cci: Fix ordering of pm_runtime_xx and i2c_add_adapter
+    - x86/microcode/AMD: Apply the patch early on every logical thread
+    - hwmon/coretemp: Handle large core ID value
+    - ata: ahci-imx: Fix MODULE_ALIAS
+    - x86/resctrl: Fix min_cbm_bits for AMD
+    - cpufreq: qcom: fix memory leak in error path
+    - drm/amdgpu: fix sdma doorbell init ordering on APUs
+    - mm,hugetlb: take hugetlb_lock before decrementing h->resv_huge_pages
+    - kvm: Add support for arch compat vm ioctls
+    - KVM: arm64: vgic: Fix exit condition in scan_its_table()
+    - media: ipu3-imgu: Fix NULL pointer dereference in active selection access
+    - media: mceusb: set timeout to at least timeout provided
+    - media: venus: dec: Handle the case where find_format fails
+    - x86/topology: Fix multiple packages shown on a single-package system
+    - x86/topology: Fix duplicated core ID within a package
+    - btrfs: fix processing of delayed data refs during backref walking
+    - btrfs: fix processing of delayed tree block refs during backref walking
+    - drm/vc4: Add module dependency on hdmi-codec
+    - ACPI: extlog: Handle multiple records
+    - tipc: Fix recognition of trial period
+    - tipc: fix an information leak in tipc_topsrv_kern_subscr
+    - i40e: Fix DMA mappings leak
+    - HID: magicmouse: Do not set BTN_MOUSE on double report
+    - sfc: Change VF mac via PF as first preference if available.
+    - net/atm: fix proc_mpc_write incorrect return value
+    - net: phy: dp83867: Extend RX strap quirk for SGMII mode
+    - net: phylink: add mac_managed_pm in phylink_config structure
+    - scsi: lpfc: Fix memory leak in lpfc_create_port()
+    - udp: Update reuse->has_conns under reuseport_lock.
+    - cifs: Fix xid leak in cifs_create()
+    - cifs: Fix xid leak in cifs_copy_file_range()
+    - cifs: Fix xid leak in cifs_flock()
+    - cifs: Fix xid leak in cifs_ses_add_channel()
+    - dm: remove unnecessary assignment statement in alloc_dev()
+    - net: hsr: avoid possible NULL deref in skb_clone()
+    - ionic: catch NULL pointer issue on reconfig
+    - netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
+    - nvme-hwmon: consistently ignore errors from nvme_hwmon_init
+    - nvme-hwmon: kmalloc the NVME SMART log buffer
+    - nvmet: fix workqueue MEM_RECLAIM flushing dependency
+    - net: sched: cake: fix null pointer access issue when cake_init() fails
+    - net: sched: delete duplicate cleanup of backlog and qlen
+    - net: sched: sfb: fix null pointer access issue when sfb_init() fails
+    - sfc: include vport_id in filter spec hash and equal()
+    - wwan_hwsim: fix possible memory leak in wwan_hwsim_dev_new()
+    - net: hns: fix possible memory leak in hnae_ae_register()
+    - net: sched: fix race condition in qdisc_graft()
+    - net: phy: dp83822: disable MDI crossover status change interrupt
+    - iommu/vt-d: Allow NVS regions in arch_rmrr_sanity_check()
+    - iommu/vt-d: Clean up si_domain in the init_dmars() error path
+    - fs: dlm: fix invalid derefence of sb_lvbptr
+    - arm64: mte: move register initialization to C
+    - ksmbd: handle smb2 query dir request for OutputBufferLength that is too
+      small
+    - ksmbd: fix incorrect handling of iterate_dir
+    - tracing: Simplify conditional compilation code in tracing_set_tracer()
+    - tracing: Do not free snapshot if tracer is on cmdline
+    - mmc: sdhci-tegra: Use actual clock rate for SW tuning correction
+    - perf: Skip and warn on unknown format 'configN' attrs
+    - ACPI: video: Force backlight native for more TongFang devices
+    - x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
+    - Makefile.debug: re-enable debug info for .S files
+    - mmc: core: Add SD card quirk for broken discard
+    - mm: /proc/pid/smaps_rollup: fix no vma's null-deref
+    - Linux 5.15.76
+
+  * UBSAN: array-index-out-of-bounds in
+    /build/linux-9H675w/linux-5.15.0/drivers/ata/libahci.c:968:41
+    (LP: #1970074) // Jammy update: v5.15.76 upstream stable release
+    (LP: #1997113)
+    - ata: ahci: Match EM_MAX_SLOTS with SATA_PMP_MAX_PORTS
+
+  * Jammy update: v5.15.75 upstream stable release (LP: #1996825)
+    - Revert "fs: check FMODE_LSEEK to control internal pipe splicing"
+    - ALSA: oss: Fix potential deadlock at unregistration
+    - ALSA: rawmidi: Drop register_mutex in snd_rawmidi_free()
+    - ALSA: usb-audio: Fix potential memory leaks
+    - ALSA: usb-audio: Fix NULL dererence at error path
+    - ALSA: hda/realtek: remove ALC289_FIXUP_DUAL_SPK for Dell 5530
+    - ALSA: hda/realtek: Correct pin configs for ASUS G533Z
+    - ALSA: hda/realtek: Add quirk for ASUS GV601R laptop
+    - ALSA: hda/realtek: Add Intel Reference SSID to support headset keys
+    - mtd: rawnand: atmel: Unmap streaming DMA mappings
+    - io_uring/net: don't update msg_name if not provided
+    - hv_netvsc: Fix race between VF offering and VF association message from host
+    - cifs: destage dirty pages before re-reading them for cache=none
+    - cifs: Fix the error length of VALIDATE_NEGOTIATE_INFO message
+    - iio: dac: ad5593r: Fix i2c read protocol requirements
+    - iio: ltc2497: Fix reading conversion results
+    - iio: adc: ad7923: fix channel readings for some variants
+    - iio: pressure: dps310: Refactor startup procedure
+    - iio: pressure: dps310: Reset chip after timeout
+    - xhci: dbc: Fix memory leak in xhci_alloc_dbc()
+    - usb: add quirks for Lenovo OneLink+ Dock
+    - can: kvaser_usb: Fix use of uninitialized completion
+    - can: kvaser_usb_leaf: Fix overread with an invalid command
+    - can: kvaser_usb_leaf: Fix TX queue out of sync after restart
+    - can: kvaser_usb_leaf: Fix CAN state after restart
+    - mmc: sdhci-sprd: Fix minimum clock limit
+    - i2c: designware: Fix handling of real but unexpected device interrupts
+    - fs: dlm: fix race between test_bit() and queue_work()
+    - fs: dlm: handle -EBUSY first in lock arg validation
+    - HID: multitouch: Add memory barriers
+    - quota: Check next/prev free block number after reading from quota file
+    - platform/chrome: cros_ec_proto: Update version on GET_NEXT_EVENT failure
+    - ASoC: wcd9335: fix order of Slimbus unprepare/disable
+    - ASoC: wcd934x: fix order of Slimbus unprepare/disable
+    - hwmon: (gsc-hwmon) Call of_node_get() before of_find_xxx API
+    - net: thunderbolt: Enable DMA paths only after rings are enabled
+    - regulator: qcom_rpm: Fix circular deferral regression
+    - arm64: topology: move store_cpu_topology() to shared code
+    - riscv: topology: fix default topology reporting
+    - RISC-V: Make port I/O string accessors actually work
+    - parisc: fbdev/stifb: Align graphics memory size to 4MB
+    - riscv: Make VM_WRITE imply VM_READ
+    - riscv: always honor the CONFIG_CMDLINE_FORCE when parsing dtb
+    - riscv: Pass -mno-relax only on lld < 15.0.0
+    - UM: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+    - nvmem: core: Fix memleak in nvmem_register()
+    - nvme-multipath: fix possible hang in live ns resize with ANA access
+    - nvme-pci: set min_align_mask before calculating max_hw_sectors
+    - dmaengine: mxs: use platform_driver_register
+    - drm/virtio: Check whether transferred 2D BO is shmem
+    - drm/virtio: Unlock reservations on virtio_gpu_object_shmem_init() error
+    - drm/virtio: Use appropriate atomic state in virtio_gpu_plane_cleanup_fb()
+    - drm/udl: Restore display mode on resume
+    - [Config] updateconfigs for ARM64_ERRATUM_2441007
+    - arm64: errata: Add Cortex-A55 to the repeat tlbi list
+    - mm/damon: validate if the pmd entry is present before accessing
+    - mm/mmap: undo ->mmap() when arch_validate_flags() fails
+    - xen/gntdev: Prevent leaking grants
+    - xen/gntdev: Accommodate VMA splitting
+    - PCI: Sanitise firmware BAR assignments behind a PCI-PCI bridge
+    - serial: 8250: Let drivers request full 16550A feature probing
+    - serial: 8250: Request full 16550A feature probing for OxSemi PCIe devices
+    - powercap: intel_rapl: Use standard Energy Unit for SPR Dram RAPL domain
+    - powerpc/boot: Explicitly disable usage of SPE instructions
+    - slimbus: qcom-ngd: use correct error in message of pdr_add_lookup() failure
+    - slimbus: qcom-ngd: cleanup in probe error path
+    - scsi: qedf: Populate sysfs attributes for vport
+    - gpio: rockchip: request GPIO mux to pinctrl when setting direction
+    - pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
+    - fbdev: smscufx: Fix use-after-free in ufx_ops_open()
+    - ksmbd: fix endless loop when encryption for response fails
+    - ksmbd: Fix wrong return value and message length check in smb2_ioctl()
+    - ksmbd: Fix user namespace mapping
+    - fs: record I_DIRTY_TIME even if inode already has I_DIRTY_INODE
+    - btrfs: fix race between quota enable and quota rescan ioctl
+    - btrfs: set generation before calling btrfs_clean_tree_block in
+      btrfs_init_new_buffer
+    - f2fs: complete checkpoints during remount
+    - f2fs: flush pending checkpoints when freezing super
+    - f2fs: increase the limit for reserve_root
+    - f2fs: fix to do sanity check on destination blkaddr during recovery
+    - f2fs: fix to do sanity check on summary info
+    - hardening: Avoid harmless Clang option under CONFIG_INIT_STACK_ALL_ZERO
+    - hardening: Remove Clang's enable flag for -ftrivial-auto-var-init=zero
+    - jbd2: wake up journal waiters in FIFO order, not LIFO
+    - jbd2: fix potential buffer head reference count leak
+    - jbd2: fix potential use-after-free in jbd2_fc_wait_bufs
+    - jbd2: add miss release buffer head in fc_do_one_pass()
+    - ext4: avoid crash when inline data creation follows DIO write
+    - ext4: fix null-ptr-deref in ext4_write_info
+    - ext4: make ext4_lazyinit_thread freezable
+    - ext4: fix check for block being out of directory size
+    - ext4: don't increase iversion counter for ea_inodes
+    - ext4: ext4_read_bh_lock() should submit IO if the buffer isn't uptodate
+    - ext4: place buffer head allocation before handle start
+    - ext4: fix dir corruption when ext4_dx_add_entry() fails
+    - ext4: fix miss release buffer head in ext4_fc_write_inode
+    - ext4: fix potential memory leak in ext4_fc_record_modified_inode()
+    - ext4: fix potential memory leak in ext4_fc_record_regions()
+    - ext4: update 'state->fc_regions_size' after successful memory allocation
+    - livepatch: fix race between fork and KLP transition
+    - ftrace: Properly unset FTRACE_HASH_FL_MOD
+    - ring-buffer: Allow splice to read previous partially read pages
+    - ring-buffer: Have the shortest_full queue be the shortest not longest
+    - ring-buffer: Check pending waiters when doing wake ups as well
+    - ring-buffer: Add ring_buffer_wake_waiters()
+    - ring-buffer: Fix race between reset page and reading page
+    - tracing: Disable interrupt or preemption before acquiring arch_spinlock_t
+    - tracing: Wake up ring buffer waiters on closing of the file
+    - tracing: Wake up waiters when tracing is disabled
+    - tracing: Add ioctl() to force ring buffer waiters to wake up
+    - tracing: Move duplicate code of trace_kprobe/eprobe.c into header
+    - tracing: Add "(fault)" name injection to kernel probes
+    - tracing: Fix reading strings from synthetic events
+    - thunderbolt: Explicitly enable lane adapter hotplug events at startup
+    - efi: libstub: drop pointless get_memory_map() call
+    - media: cedrus: Set the platform driver data earlier
+    - media: cedrus: Fix endless loop in cedrus_h265_skip_bits()
+    - blk-wbt: call rq_qos_add() after wb_normal is initialized
+    - KVM: x86/emulator: Fix handing of POP SS to correctly set interruptibility
+    - KVM: nVMX: Unconditionally purge queued/injected events on nested "exit"
+    - KVM: nVMX: Don't propagate vmcs12's PERF_GLOBAL_CTRL settings to vmcs02
+    - KVM: VMX: Drop bits 31:16 when shoving exception error code into VMCS
+    - staging: greybus: audio_helper: remove unused and wrong debugfs usage
+    - drm/nouveau/kms/nv140-: Disable interlacing
+    - drm/nouveau: fix a use-after-free in nouveau_gem_prime_import_sg_table()
+    - drm/i915: Fix watermark calculations for gen12+ RC CCS modifier
+    - drm/i915: Fix watermark calculations for gen12+ MC CCS modifier
+    - drm/i915: Fix watermark calculations for gen12+ CCS+CC modifier
+    - drm/amd/display: Fix vblank refcount in vrr transition
+    - smb3: must initialize two ACL struct fields to zero
+    - selinux: use "grep -E" instead of "egrep"
+    - ima: fix blocking of security.ima xattrs of unsupported algorithms
+    - userfaultfd: open userfaultfds with O_RDONLY
+    - ntfs3: rework xattr handlers and switch to POSIX ACL VFS helpers
+    - thermal: cpufreq_cooling: Check the policy first in
+      cpufreq_cooling_register()
+    - sh: machvec: Use char[] for section boundaries
+    - MIPS: SGI-IP27: Free some unused memory
+    - MIPS: SGI-IP27: Fix platform-device leak in bridge_platform_create()
+    - ARM: 9244/1: dump: Fix wrong pg_level in walk_pmd()
+    - ARM: 9247/1: mm: set readonly for MT_MEMORY_RO with ARM_LPAE
+    - objtool: Preserve special st_shndx indexes in elf_update_symbol
+    - nfsd: Fix a memory leak in an error handling path
+    - NFSD: Fix handling of oversized NFSv4 COMPOUND requests
+    - wifi: rtlwifi: 8192de: correct checking of IQK reload
+    - wifi: ath10k: add peer map clean up for peer delete in ath10k_sta_state()
+    - leds: lm3601x: Don't use mutex after it was destroyed
+    - bpf: Fix reference state management for synchronous callbacks
+    - wifi: mac80211: allow bw change during channel switch in mesh
+    - bpftool: Fix a wrong type cast in btf_dumper_int
+    - spi: mt7621: Fix an error message in mt7621_spi_probe()
+    - x86/resctrl: Fix to restore to original value when re-enabling hardware
+      prefetch register
+    - xsk: Fix backpressure mechanism on Tx
+    - bpf: Disable preemption when increasing per-cpu map_locked
+    - bpf: Propagate error from htab_lock_bucket() to userspace
+    - bpf: Use this_cpu_{inc|dec|inc_return} for bpf_task_storage_busy
+    - Bluetooth: btusb: mediatek: fix WMT failure during runtime suspend
+    - wifi: rtl8xxxu: tighten bounds checking in rtl8xxxu_read_efuse()
+    - wifi: rtw88: add missing destroy_workqueue() on error path in
+      rtw_core_init()
+    - selftests/xsk: Avoid use-after-free on ctx
+    - spi: qup: add missing clk_disable_unprepare on error in spi_qup_resume()
+    - spi: qup: add missing clk_disable_unprepare on error in
+      spi_qup_pm_resume_runtime()
+    - wifi: rtl8xxxu: Fix skb misuse in TX queue selection
+    - spi: meson-spicc: do not rely on busy flag in pow2 clk ops
+    - bpf: btf: fix truncated last_member_type_id in btf_struct_resolve
+    - wifi: rtl8xxxu: gen2: Fix mistake in path B IQ calibration
+    - wifi: rtl8xxxu: Remove copy-paste leftover in gen2_update_rate_mask
+    - wifi: mt76: sdio: fix transmitting packet hangs
+    - wifi: mt76: mt7615: add mt7615_mutex_acquire/release in
+      mt7615_sta_set_decap_offload
+    - wifi: mt76: mt7915: do not check state before configuring implicit beamform
+    - Bluetooth: RFCOMM: Fix possible deadlock on socket shutdown/release
+    - net: fs_enet: Fix wrong check in do_pd_setup
+    - bpf: Ensure correct locking around vulnerable function find_vpid()
+    - Bluetooth: hci_{ldisc,serdev}: check percpu_init_rwsem() failure
+    - netfilter: conntrack: fix the gc rescheduling delay
+    - netfilter: conntrack: revisit the gc initial rescheduling bias
+    - wifi: ath11k: fix number of VHT beamformee spatial streams
+    - x86/microcode/AMD: Track patch allocation size explicitly
+    - x86/cpu: Include the header of init_ia32_feat_ctl()'s prototype
+    - spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
+    - spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
+    - skmsg: Schedule psock work if the cached skb exists on the psock
+    - i2c: mlxbf: support lock mechanism
+    - Bluetooth: hci_core: Fix not handling link timeouts propertly
+    - xfrm: Reinject transport-mode packets through workqueue
+    - netfilter: nft_fib: Fix for rpath check with VRF devices
+    - spi: s3c64xx: Fix large transfers with DMA
+    - wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
+    - vhost/vsock: Use kvmalloc/kvfree for larger packets.
+    - eth: alx: take rtnl_lock on resume
+    - sctp: handle the error returned from sctp_auth_asoc_init_active_key
+    - tcp: fix tcp_cwnd_validate() to not forget is_cwnd_limited
+    - spi: Ensure that sg_table won't be used after being freed
+    - hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888
+      controller
+    - net: rds: don't hold sock lock when cancelling work from
+      rds_tcp_reset_callbacks()
+    - bnx2x: fix potential memory leak in bnx2x_tpa_stop()
+    - net: wwan: iosm: Call mutex_init before locking it
+    - net/ieee802154: reject zero-sized raw_sendmsg()
+    - once: add DO_ONCE_SLOW() for sleepable contexts
+    - net: mvpp2: fix mvpp2 debugfs leak
+    - drm: bridge: adv7511: fix CEC power down control register offset
+    - drm: bridge: adv7511: unregister cec i2c device after cec adapter
+    - drm/bridge: Avoid uninitialized variable warning
+    - drm/mipi-dsi: Detach devices when removing the host
+    - drm/virtio: Correct drm_gem_shmem_get_sg_table() error handling
+    - drm/bridge: parade-ps8640: Fix regulator supply order
+    - drm/dp_mst: fix drm_dp_dpcd_read return value checks
+    - drm:pl111: Add of_node_put() when breaking out of
+      for_each_available_child_of_node()
+    - ASoC: mt6359: fix tests for platform_get_irq() failure
+    - platform/chrome: fix double-free in chromeos_laptop_prepare()
+    - platform/chrome: fix memory corruption in ioctl
+    - ASoC: tas2764: Allow mono streams
+    - ASoC: tas2764: Drop conflicting set_bias_level power setting
+    - ASoC: tas2764: Fix mute/unmute
+    - platform/x86: msi-laptop: Fix old-ec check for backlight registering
+    - platform/x86: msi-laptop: Fix resource cleanup
+    - platform/chrome: cros_ec_typec: Correct alt mode index
+    - drm/amdgpu: add missing pci_disable_device() in
+      amdgpu_pmops_runtime_resume()
+    - drm/bridge: megachips: Fix a null pointer dereference bug
+    - ASoC: rsnd: Add check for rsnd_mod_power_on
+    - ALSA: hda: beep: Simplify keep-power-at-enable behavior
+    - drm/bochs: fix blanking
+    - drm/omap: dss: Fix refcount leak bugs
+    - drm/amdgpu: Fix memory leak in hpd_rx_irq_create_workqueue()
+    - mmc: au1xmmc: Fix an error handling path in au1xmmc_probe()
+    - ASoC: eureka-tlv320: Hold reference returned from of_find_xxx API
+    - drm/msm/dpu: index dpu_kms->hw_vbif using vbif_idx
+    - drm/msm/dp: correct 1.62G link rate at dp_catalog_ctrl_config_msa()
+    - drm/vmwgfx: Fix memory leak in vmw_mksstat_add_ioctl()
+    - ASoC: codecs: tx-macro: fix kcontrol put
+    - ASoC: da7219: Fix an error handling path in da7219_register_dai_clks()
+    - ALSA: dmaengine: increment buffer pointer atomically
+    - mmc: wmt-sdmmc: Fix an error handling path in wmt_mci_probe()
+    - ASoC: wm8997: Fix PM disable depth imbalance in wm8997_probe
+    - ASoC: wm5110: Fix PM disable depth imbalance in wm5110_probe
+    - ASoC: wm5102: Fix PM disable depth imbalance in wm5102_probe
+    - ASoC: mt6660: Fix PM disable depth imbalance in mt6660_i2c_probe
+    - ALSA: hda/hdmi: Don't skip notification handling during PM operation
+    - memory: pl353-smc: Fix refcount leak bug in pl353_smc_probe()
+    - memory: of: Fix refcount leak bug in of_get_ddr_timings()
+    - memory: of: Fix refcount leak bug in of_lpddr3_get_ddr_timings()
+    - locks: fix TOCTOU race when granting write lease
+    - soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
+    - soc: qcom: smem_state: Add refcounting for the 'state->of_node'
+    - ARM: dts: imx6qdl-kontron-samx6i: hook up DDC i2c bus
+    - ARM: dts: turris-omnia: Fix mpp26 pin name and comment
+    - ARM: dts: kirkwood: lsxl: fix serial line
+    - ARM: dts: kirkwood: lsxl: remove first ethernet port
+    - ia64: export memory_add_physaddr_to_nid to fix cxl build error
+    - soc/tegra: fuse: Drop Kconfig dependency on TEGRA20_APB_DMA
+    - arm64: dts: ti: k3-j7200: fix main pinmux range
+    - ARM: dts: exynos: correct s5k6a3 reset polarity on Midas family
+    - ARM: Drop CMDLINE_* dependency on ATAGS
+    - ext4: don't run ext4lazyinit for read-only filesystems
+    - arm64: ftrace: fix module PLTs with mcount
+    - ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
+    - iio: adc: at91-sama5d2_adc: fix AT91_SAMA5D2_MR_TRACKTIM_MAX
+    - iio: adc: at91-sama5d2_adc: check return status for pressure and touch
+    - iio: adc: at91-sama5d2_adc: lock around oversampling and sample freq
+    - iio: adc: at91-sama5d2_adc: disable/prepare buffer on suspend/resume
+    - iio: inkern: only release the device node when done with it
+    - iio: inkern: fix return value in devm_of_iio_channel_get_by_name()
+    - iio: ABI: Fix wrong format of differential capacitance channel ABI.
+    - iio: magnetometer: yas530: Change data type of hard_offsets to signed
+    - RDMA/mlx5: Don't compare mkey tags in DEVX indirect mkey
+    - usb: common: debug: Check non-standard control requests
+    - clk: meson: Hold reference returned by of_get_parent()
+    - clk: oxnas: Hold reference returned by of_get_parent()
+    - clk: qoriq: Hold reference returned by of_get_parent()
+    - clk: berlin: Add of_node_put() for of_get_parent()
+    - clk: sprd: Hold reference returned by of_get_parent()
+    - clk: tegra: Fix refcount leak in tegra210_clock_init
+    - clk: tegra: Fix refcount leak in tegra114_clock_init
+    - clk: tegra20: Fix refcount leak in tegra20_clock_init
+    - HSI: omap_ssi: Fix refcount leak in ssi_probe
+    - HSI: omap_ssi_port: Fix dma_map_sg error check
+    - media: exynos4-is: fimc-is: Add of_node_put() when breaking out of loop
+    - tty: xilinx_uartps: Fix the ignore_status
+    - media: meson: vdec: add missing clk_disable_unprepare on error in
+      vdec_hevc_start()
+    - media: uvcvideo: Fix memory leak in uvc_gpio_parse
+    - media: uvcvideo: Use entity get_cur in uvc_ctrl_set
+    - media: xilinx: vipp: Fix refcount leak in xvip_graph_dma_init
+    - RDMA/rxe: Fix "kernel NULL pointer dereference" error
+    - RDMA/rxe: Fix the error caused by qp->sk
+    - misc: ocxl: fix possible refcount leak in afu_ioctl()
+    - fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
+    - dmaengine: hisilicon: Disable channels when unregister hisi_dma
+    - dmaengine: hisilicon: Fix CQ head update
+    - dmaengine: hisilicon: Add multi-thread support for a DMA channel
+    - dyndbg: fix static_branch manipulation
+    - dyndbg: fix module.dyndbg handling
+    - dyndbg: let query-modname override actual module name
+    - dyndbg: drop EXPORTed dynamic_debug_exec_queries
+    - clk: qcom: sm6115: Select QCOM_GDSC
+    - mtd: devices: docg3: check the return value of devm_ioremap() in the probe
+    - phy: amlogic: phy-meson-axg-mipi-pcie-analog: Hold reference returned by
+      of_get_parent()
+    - phy: phy-mtk-tphy: fix the phy type setting issue
+    - mtd: rawnand: intel: Read the chip-select line from the correct OF node
+    - mtd: rawnand: intel: Remove undocumented compatible string
+    - mtd: rawnand: fsl_elbc: Fix none ECC mode
+    - RDMA/irdma: Align AE id codes to correct flush code and event
+    - RDMA/srp: Fix srp_abort()
+    - RDMA/siw: Always consume all skbuf data in sk_data_ready() upcall.
+    - RDMA/siw: Fix QP destroy to wait for all references dropped.
+    - ata: fix ata_id_sense_reporting_enabled() and ata_id_has_sense_reporting()
+    - ata: fix ata_id_has_devslp()
+    - ata: fix ata_id_has_ncq_autosense()
+    - ata: fix ata_id_has_dipm()
+    - mtd: rawnand: meson: fix bit map use in meson_nfc_ecc_correct()
+    - md/raid5: Ensure stripe_fill happens on non-read IO with journal
+    - md/raid5: Remove unnecessary bio_put() in raid5_read_one_chunk()
+    - RDMA/cm: Use SLID in the work completion as the DLID in responder side
+    - IB: Set IOVA/LENGTH on IB_MR in core/uverbs layers
+    - xhci: Don't show warning for reinit on known broken suspend
+    - usb: gadget: function: fix dangling pnp_string in f_printer.c
+    - drivers: serial: jsm: fix some leaks in probe
+    - serial: 8250: Toggle IER bits on only after irq has been set up
+    - tty: serial: fsl_lpuart: disable dma rx/tx use flags in lpuart_dma_shutdown
+    - phy: qualcomm: call clk_disable_unprepare in the error handling
+    - staging: vt6655: fix some erroneous memory clean-up loops
+    - slimbus: qcom-ngd-ctrl: allow compile testing without QCOM_RPROC_COMMON
+    - firmware: google: Test spinlock on panic path to avoid lockups
+    - serial: 8250: Fix restoring termios speed after suspend
+    - scsi: libsas: Fix use-after-free bug in smp_execute_task_sg()
+    - scsi: iscsi: Rename iscsi_conn_queue_work()
+    - scsi: iscsi: Add recv workqueue helpers
+    - scsi: iscsi: Run recv path from workqueue
+    - scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
+    - clk: qcom: apss-ipq6018: mark apcs_alias0_core_clk as critical
+    - clk: qcom: gcc-sm6115: Override default Alpha PLL regs
+    - RDMA/rxe: Fix resize_finish() in rxe_queue.c
+    - fsi: core: Check error number after calling ida_simple_get
+    - mfd: intel_soc_pmic: Fix an error handling path in
+      intel_soc_pmic_i2c_probe()
+    - mfd: fsl-imx25: Fix an error handling path in mx25_tsadc_setup_irq()
+    - mfd: lp8788: Fix an error handling path in lp8788_probe()
+    - mfd: lp8788: Fix an error handling path in lp8788_irq_init() and
+      lp8788_irq_init()
+    - mfd: fsl-imx25: Fix check for platform_get_irq() errors
+    - mfd: sm501: Add check for platform_driver_register()
+    - clk: mediatek: mt8183: mfgcfg: Propagate rate changes to parent
+    - dmaengine: ioat: stop mod_timer from resurrecting deleted timer in
+      __cleanup()
+    - usb: mtu3: fix failed runtime suspend in host only mode
+    - spmi: pmic-arb: correct duplicate APID to PPID mapping logic
+    - clk: vc5: Fix 5P49V6901 outputs disabling when enabling FOD
+    - clk: baikal-t1: Fix invalid xGMAC PTP clock divider
+    - clk: baikal-t1: Add shared xGMAC ref/ptp clocks internal parent
+    - clk: baikal-t1: Add SATA internal ref clock buffer
+    - clk: bcm2835: fix bcm2835_clock_rate_from_divisor declaration
+    - clk: imx: scu: fix memleak on platform_device_add() fails
+    - clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
+    - clk: ast2600: BCLK comes from EPLL
+    - mailbox: mpfs: fix handling of the reg property
+    - mailbox: mpfs: account for mbox offsets while sending
+    - mailbox: bcm-ferxrm-mailbox: Fix error check for dma_map_sg
+    - powerpc/configs: Properly enable PAPR_SCM in pseries_defconfig
+    - powerpc/math_emu/efp: Include module.h
+    - powerpc/sysdev/fsl_msi: Add missing of_node_put()
+    - powerpc/pci_dn: Add missing of_node_put()
+    - powerpc/powernv: add missing of_node_put() in opal_export_attrs()
+    - powerpc: Fix fallocate and fadvise64_64 compat parameter combination
+    - x86/hyperv: Fix 'struct hv_enlightened_vmcs' definition
+    - powerpc/64s: Fix GENERIC_CPU build flags for PPC970 / G5
+    - powerpc: Fix SPE Power ISA properties for e500v1 platforms
+    - powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
+    - powerpc/pseries/vas: Pass hw_cpu_id to node associativity HCALL
+    - crypto: sahara - don't sleep when in softirq
+    - crypto: hisilicon/zip - fix mismatch in get/set sgl_sge_nr
+    - hwrng: arm-smccc-trng - fix NO_ENTROPY handling
+    - cgroup: Honor caller's cgroup NS when resolving path
+    - hwrng: imx-rngc - Moving IRQ handler registering after
+      imx_rngc_irq_mask_clear()
+    - crypto: qat - fix default value of WDT timer
+    - crypto: hisilicon/qm - fix missing put dfx access
+    - cgroup/cpuset: Enable update_tasks_cpumask() on top_cpuset
+    - iommu/omap: Fix buffer overflow in debugfs
+    - crypto: akcipher - default implementation for setting a private key
+    - crypto: ccp - Release dma channels before dmaengine unrgister
+    - crypto: inside-secure - Change swab to swab32
+    - crypto: qat - fix DMA transfer direction
+    - cifs: return correct error in ->calc_signature()
+    - iommu/iova: Fix module config properly
+    - tracing: kprobe: Fix kprobe event gen test module on exit
+    - tracing: kprobe: Make gen test module work in arm and riscv
+    - tracing/osnoise: Fix possible recursive locking in stop_per_cpu_kthreads
+    - kbuild: remove the target in signal traps when interrupted
+    - kbuild: rpm-pkg: fix breakage when V=1 is used
+    - crypto: marvell/octeontx - prevent integer overflows
+    - crypto: cavium - prevent integer overflow loading firmware
+    - thermal/drivers/qcom/tsens-v0_1: Fix MSM8939 fourth sensor hw_id
+    - ACPI: APEI: do not add task_work to kernel thread to avoid memory leak
+    - f2fs: fix race condition on setting FI_NO_EXTENT flag
+    - f2fs: fix to account FS_CP_DATA_IO correctly
+    - selftest: tpm2: Add Client.__del__() to close /dev/tpm* handle
+    - fs: dlm: fix race in lowcomms
+    - rcu: Avoid triggering strict-GP irq-work when RCU is idle
+    - rcu: Back off upon fill_page_cache_func() allocation failure
+    - rcu-tasks: Convert RCU_LOCKDEP_WARN() to WARN_ONCE()
+    - ACPI: video: Add Toshiba Satellite/Portege Z830 quirk
+    - ACPI: tables: FPDT: Don't call acpi_os_map_memory() on invalid phys address
+    - cpufreq: intel_pstate: Add Tigerlake support in no-HWP mode
+    - MIPS: BCM47XX: Cast memcmp() of function to (void *)
+    - powercap: intel_rapl: fix UBSAN shift-out-of-bounds issue
+    - thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to
+      avoid crash
+    - ARM: decompressor: Include .data.rel.ro.local
+    - ACPI: x86: Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable
+    - x86/entry: Work around Clang __bdos() bug
+    - NFSD: Return nfserr_serverfault if splice_ok but buf->pages have data
+    - NFSD: fix use-after-free on source server when doing inter-server copy
+    - wifi: brcmfmac: fix invalid address access when enabling SCAN log level
+    - bpftool: Clear errno after libcap's checks
+    - ice: set tx_tstamps when creating new Tx rings via ethtool
+    - net: ethernet: ti: davinci_mdio: Add workaround for errata i2329
+    - openvswitch: Fix double reporting of drops in dropwatch
+    - openvswitch: Fix overreporting of drops in dropwatch
+    - tcp: annotate data-race around tcp_md5sig_pool_populated
+    - x86/mce: Retrieve poison range from hardware
+    - wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
+    - thunderbolt: Add back Intel Falcon Ridge end-to-end flow control workaround
+    - xfrm: Update ipcomp_scratches with NULL when freed
+    - iavf: Fix race between iavf_close and iavf_reset_task
+    - wifi: brcmfmac: fix use-after-free bug in brcmf_netdev_start_xmit()
+    - Bluetooth: btintel: Mark Intel controller to support LE_STATES quirk
+    - regulator: core: Prevent integer underflow
+    - wifi: mt76: mt7921: reset msta->airtime_ac while clearing up hw value
+    - Bluetooth: L2CAP: initialize delayed works at l2cap_chan_create()
+    - Bluetooth: hci_sysfs: Fix attempting to call device_add multiple times
+    - can: bcm: check the result of can_send() in bcm_can_tx()
+    - wifi: rt2x00: don't run Rt5592 IQ calibration on MT7620
+    - wifi: rt2x00: set correct TX_SW_CFG1 MAC register for MT7620
+    - wifi: rt2x00: set VGC gain for both chains of MT7620
+    - wifi: rt2x00: set SoC wmac clock register
+    - wifi: rt2x00: correctly set BBP register 86 for MT7620
+    - hwmon: (sht4x) do not overflow clamping operation on 32-bit platforms
+    - net: If sock is dead don't access sock's sk_wq in sk_stream_wait_memory
+    - Bluetooth: L2CAP: Fix user-after-free
+    - drm/nouveau/nouveau_bo: fix potential memory leak in nouveau_bo_alloc()
+    - drm: Use size_t type for len variable in drm_copy_field()
+    - drm: Prevent drm_copy_field() to attempt copying a NULL pointer
+    - drm/komeda: Fix handling of atomic commits in the atomic_commit_tail hook
+    - gpu: lontium-lt9611: Fix NULL pointer dereference in lt9611_connector_init()
+    - drm/amd/display: fix overflow on MIN_I64 definition
+    - udmabuf: Set ubuf->sg = NULL if the creation of sg table fails
+    - drm: bridge: dw_hdmi: only trigger hotplug event on link change
+    - ALSA: usb-audio: Register card at the last interface
+    - drm/vc4: vec: Fix timings for VEC modes
+    - drm: panel-orientation-quirks: Add quirk for Anbernic Win600
+    - platform/chrome: cros_ec: Notify the PM of wake events during resume
+    - platform/x86: msi-laptop: Change DMI match / alias strings to fix module
+      autoloading
+    - ASoC: SOF: pci: Change DMI match info to support all Chrome platforms
+    - drm/amdgpu: fix initial connector audio value
+    - drm/meson: reorder driver deinit sequence to fix use-after-free bug
+    - drm/meson: explicitly remove aggregate driver at module unload time
+    - mmc: sdhci-msm: add compatible string check for sdm670
+    - drm/dp: Don't rewrite link config when setting phy test pattern
+    - drm/amd/display: Remove interface for periodic interrupt 1
+    - ARM: dts: imx7d-sdb: config the max pressure for tsc2046
+    - ARM: dts: imx6q: add missing properties for sram
+    - ARM: dts: imx6dl: add missing properties for sram
+    - ARM: dts: imx6qp: add missing properties for sram
+    - ARM: dts: imx6sl: add missing properties for sram
+    - ARM: dts: imx6sll: add missing properties for sram
+    - ARM: dts: imx6sx: add missing properties for sram
+    - kselftest/arm64: Fix validatation termination record after EXTRA_CONTEXT
+    - arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply
+    - btrfs: dump extra info if one free space cache has more bitmaps than it
+      should
+    - btrfs: scrub: try to fix super block errors
+    - btrfs: don't print information about space cache or tree every remount
+    - ARM: 9242/1: kasan: Only map modules if CONFIG_KASAN_VMALLOC=n
+    - clk: zynqmp: Fix stack-out-of-bounds in strncpy`
+    - media: cx88: Fix a null-ptr-deref bug in buffer_prepare()
+    - media: platform: fix some double free in meson-ge2d and mtk-jpeg and s5p-mfc
+    - clk: zynqmp: pll: rectify rate rounding in zynqmp_pll_round_rate
+    - usb: host: xhci-plat: suspend and resume clocks
+    - usb: host: xhci-plat: suspend/resume clks for brcm
+    - dmaengine: ti: k3-udma: Reset UDMA_CHAN_RT byte counters to prevent overflow
+    - scsi: 3w-9xxx: Avoid disabling device if failing to enable it
+    - nbd: Fix hung when signal interrupts nbd_start_device_ioctl()
+    - iommu/arm-smmu-v3: Make default domain type of HiSilicon PTT device to
+      identity
+    - power: supply: adp5061: fix out-of-bounds read in adp5061_get_chg_type()
+    - staging: vt6655: fix potential memory leak
+    - blk-throttle: prevent overflow while calculating wait time
+    - ata: libahci_platform: Sanity check the DT child nodes number
+    - bcache: fix set_at_max_writeback_rate() for multiple attached devices
+    - soundwire: cadence: Don't overwrite msg->buf during write commands
+    - soundwire: intel: fix error handling on dai registration issues
+    - HID: roccat: Fix use-after-free in roccat_read()
+    - eventfd: guard wake_up in eventfd fs calls as well
+    - md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d
+    - usb: host: xhci: Fix potential memory leak in xhci_alloc_stream_info()
+    - usb: musb: Fix musb_gadget.c rxstate overflow bug
+    - arm64: dts: imx8mp: Add snps,gfladj-refclk-lpm-sel quirk to USB nodes
+    - usb: dwc3: core: Enable GUCTL1 bit 10 for fixing termination error after
+      resume bug
+    - Revert "usb: storage: Add quirk for Samsung Fit flash"
+    - staging: rtl8723bs: fix potential memory leak in rtw_init_drv_sw()
+    - staging: rtl8723bs: fix a potential memory leak in rtw_init_cmd_priv()
+    - scsi: tracing: Fix compile error in trace_array calls when TRACING is
+      disabled
+    - ext2: Use kvmalloc() for group descriptor array
+    - nvme: copy firmware_rev on each init
+    - nvmet-tcp: add bounds check on Transfer Tag
+    - usb: idmouse: fix an uninit-value in idmouse_open
+    - clk: bcm2835: Make peripheral PLLC critical
+    - clk: bcm2835: Round UART input clock up
+    - perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
+    - io_uring: correct pinned_vm accounting
+    - io_uring/rw: fix short rw error handling
+    - io_uring/rw: fix error'ed retry return values
+    - io_uring/rw: fix unexpected link breakage
+    - mm: hugetlb: fix UAF in hugetlb_handle_userfault
+    - net: ieee802154: return -EINVAL for unknown addr type
+    - ALSA: usb-audio: Fix last interface check for registration
+    - blk-wbt: fix that 'rwb->wc' is always set to 1 in wbt_init()
+    - [Config] updateconfigs for MDIO_BITBANG
+    - net: ethernet: ti: davinci_mdio: fix build for mdio bitbang uses
+    - Revert "net/ieee802154: reject zero-sized raw_sendmsg()"
+    - net/ieee802154: don't warn zero-sized raw_sendmsg()
+    - drm/amd/display: Fix build breakage with CONFIG_DEBUG_FS=n
+    - Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
+    - Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
+    - lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
+    - [Config] updateconfigs for AS_HAS_NON_CONST_LEB128
+    - ext4: continue to expand file system when the target size doesn't reach
+    - thermal: intel_powerclamp: Use first online CPU as control_cpu
+    - gcov: support GCC 12.1 and newer compilers
+    - io-wq: Fix memory leak in worker creation
+    - Linux 5.15.75
+
+  * [SRU] Ubuntu 22.04 - NVMe TCP - Host fails to reconnect to target after
+    link down/link up sequence (LP: #1989990)
+    - nvme-fabrics: parse nvme connect Linux error codes
+    - nvme-tcp: handle number of queue changes
+    - nvme-rdma: handle number of queue changes
+    - nvmet: expose max queues to configfs
+
+ -- Luke Nowakowski-Krijger <luke.nowakowskikrijger@canonical.com>  Fri, 06 Jan 2023 08:11:23 -0800
+
+linux (5.15.0-58.64) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-58.64 -proposed tracker (LP: #2001670)
+
+  * CVE-2022-3643
+    - xen/netback: Ensure protocol headers don't fall in the non-linear area
+
+  * CVE-2022-4378
+    - proc: proc_skip_spaces() shouldn't think it is working on C strings
+    - proc: avoid integer type confusion in get_proc_long
+
+  * CVE-2022-45934
+    - Bluetooth: L2CAP: Fix u8 overflow
+
+  * CVE-2022-42896
+    - Bluetooth: L2CAP: Fix accepting connection request for invalid SPSM
+    - Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Thu, 05 Jan 2023 08:07:03 -0300
+
+linux (5.15.0-57.63) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-57.63 -proposed tracker (LP: #1997737)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2022.11.14)
+
+  * Expose built-in trusted and revoked certificates (LP: #1996892)
+    - [Packaging] Expose built-in trusted and revoked certificates
+
+  * TEE Support for CCP driver (LP: #1991608)
+    - crypto: ccp: Add support for TEE for PCI ID 0x14CA
+
+  * alsa: soc: the kernel print UBSAN calltrace on the machine with cs35l41
+    codec (LP: #1996121)
+    - ASoC: cs35l41: Add one more variable in the debug log
+    - ASoC: cs35l41: Fix an out-of-bounds access in otp_packed_element_t
+
+  * Fix ath11k deadlock on WCN6855 (LP: #1995041)
+    - wifi: ath11k: avoid deadlock during regulatory update in
+      ath11k_regd_update()
+
+  * [UBUNTU 20.04] boot: Add s390x secure boot trailer (LP: #1996071)
+    - s390/boot: add secure boot trailer
+
+  * Fix rfkill causing soft blocked wifi (LP: #1996198)
+    - platform/x86: hp_wmi: Fix rfkill causing soft blocked wifi
+
+  * Fix Thunderbolt device hotplug fail when connect via thunderbolt dock
+    (LP: #1991366)
+    - PCI: Fix used_buses calculation in pci_scan_child_bus_extend()
+    - PCI: Pass available buses even if the bridge is already configured
+    - PCI: Move pci_assign_unassigned_root_bus_resources()
+    - PCI: Distribute available resources for root buses, too
+    - PCI: Fix whitespace and indentation
+    - PCI: Fix typo in pci_scan_child_bus_extend()
+
+  * md: Replace snprintf with scnprintf (LP: #1993315)
+    - md: Replace snprintf with scnprintf
+
+  * input/keyboard: the keyboard on some Asus laptops can't work (LP: #1992266)
+    - ACPI: resource: Skip IRQ override on Asus Vivobook K3402ZA/K3502ZA
+    - ACPI: resource: Add ASUS model S5402ZA to quirks
+
+  * Fix Turbostat is not working for fam: 6 model: 191: stepping: 2 CPU
+    (LP: #1991365)
+    - tools/power turbostat: Add support for RPL-S
+
+  * pcieport 0000:00:1b.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal),
+    type=Transaction Layer, (Requester ID) (LP: #1988797)
+    - PCI/PTM: Cache PTM Capability offset
+    - PCI/PTM: Add pci_upstream_ptm() helper
+    - PCI/PTM: Separate configuration and enable
+    - PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
+    - PCI/PTM: Move pci_ptm_info() body into its only caller
+    - PCI/PTM: Preserve RsvdP bits in PTM Control register
+    - PCI/PTM: Reorder functions in logical order
+    - PCI/PTM: Consolidate PTM interface declarations
+    - PCI/PM: Always disable PTM for all devices during suspend
+    - PCI/PM: Simplify pci_pm_suspend_noirq()
+
+  * Fix RPL-S support on powercap/intel_rapl (LP: #1990161)
+    - x86/cpu: Drop spurious underscore from RAPTOR_LAKE #define
+    - x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
+    - x86/cpu: Add new Raptor Lake CPU model number
+    - powercap: intel_rapl: add support for RaptorLake
+    - powercap: intel_rapl: Add support for RAPTORLAKE_P
+    - powercap: intel_rapl: Add support for RAPTORLAKE_S
+
+  * AMD Yellow Carp system hang on HDMI plug in/out over HP hook2 docking
+    (LP: #1991974)
+    - drm/amd/display: Fix for link encoder access for MST.
+    - drm/amd/display: Fix MST link encoder availability check.
+    - drm/amd/display: FEC configuration for dpia links
+    - drm/amd/display: FEC configuration for dpia links in MST mode
+    - drm/amd/display: Add work around for tunneled MST.
+
+  * Jammy update: v5.15.74 upstream stable release (LP: #1995638)
+    - nilfs2: fix use-after-free bug of struct nilfs_root
+    - nilfs2: fix leak of nilfs_root in case of writer thread creation failure
+    - nilfs2: replace WARN_ONs by nilfs_error for checkpoint acquisition failure
+    - ceph: don't truncate file in atomic_open
+    - random: restore O_NONBLOCK support
+    - random: clamp credited irq bits to maximum mixed
+    - ALSA: hda: Fix position reporting on Poulsbo
+    - efi: Correct Macmini DMI match in uefi cert quirk
+    - USB: serial: qcserial: add new usb-id for Dell branded EM7455
+    - Revert "powerpc/rtas: Implement reentrant rtas call"
+    - Revert "crypto: qat - reduce size of mapped region"
+    - random: avoid reading two cache lines on irq randomness
+    - random: use expired timer rather than wq for mixing fast pool
+    - Input: xpad - add supported devices as contributed on github
+    - Input: xpad - fix wireless 360 controller breaking after suspend
+    - misc: pci_endpoint_test: Aggregate params checking for xfer
+    - misc: pci_endpoint_test: Fix pci_endpoint_test_{copy,write,read}() panic
+    - Linux 5.15.74
+
+  * Jammy update: v5.15.73 upstream stable release (LP: #1995637)
+    - Makefile.extrawarn: Move -Wcast-function-type-strict to W=1
+    - docs: update mediator information in CoC docs
+    - xsk: Inherit need_wakeup flag for shared sockets
+    - mm: gup: fix the fast GUP race against THP collapse
+    - powerpc/64s/radix: don't need to broadcast IPI for radix pmd collapse flush
+    - firmware: arm_scmi: Improve checks in the info_get operations
+    - firmware: arm_scmi: Harden accesses to the sensor domains
+    - firmware: arm_scmi: Add SCMI PM driver remove routine
+    - dmaengine: xilinx_dma: Fix devm_platform_ioremap_resource error handling
+    - dmaengine: xilinx_dma: cleanup for fetching xlnx,num-fstores property
+    - dmaengine: xilinx_dma: Report error in case of dma_set_mask_and_coherent API
+      failure
+    - ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
+    - scsi: qedf: Fix a UAF bug in __qedf_probe()
+    - net/ieee802154: fix uninit value bug in dgram_sendmsg
+    - net: marvell: prestera: add support for for Aldrin2
+    - ALSA: hda/hdmi: Fix the converter reuse for the silent stream
+    - um: Cleanup syscall_handler_t cast in syscalls_32.h
+    - um: Cleanup compiler warning in arch/x86/um/tls_32.c
+    - arch: um: Mark the stack non-executable to fix a binutils warning
+    - net: atlantic: fix potential memory leak in aq_ndev_close()
+    - drm/amd/display: Fix double cursor on non-video RGB MPO
+    - drm/amd/display: Assume an LTTPR is always present on fixed_vs links
+    - drm/amd/display: update gamut remap if plane has changed
+    - drm/amd/display: skip audio setup when audio stream is enabled
+    - mmc: core: Replace with already defined values for readability
+    - mmc: core: Terminate infinite loop in SD-UHS voltage switch
+    - perf parse-events: Identify broken modifiers
+    - mm/huge_memory: minor cleanup for split_huge_pages_all
+    - mm/huge_memory: use pfn_to_online_page() in split_huge_pages_all()
+    - wifi: cfg80211: fix MCS divisor value
+    - net/mlx5: Disable irq when locking lag_lock
+    - usb: mon: make mmapped memory read only
+    - USB: serial: ftdi_sio: fix 300 bps rate for SIO
+    - rpmsg: qcom: glink: replace strncpy() with strscpy_pad()
+    - Revert "clk: ti: Stop using legacy clkctrl names for omap4 and 5"
+    - Linux 5.15.73
+
+  * Jammy update: v5.15.72 upstream stable release (LP: #1995517)
+    - ALSA: hda: Do disconnect jacks at codec unbind
+    - ALSA: hda: Fix hang at HD-audio codec unbinding due to refcount saturation
+    - ALSA: hda: Fix Nvidia dp infoframe
+    - cgroup: reduce dependency on cgroup_mutex
+    - cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
+    - uas: add no-uas quirk for Hiksemi usb_disk
+    - usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS
+    - uas: ignore UAS for Thinkplus chips
+    - usb: typec: ucsi: Remove incorrect warning
+    - thunderbolt: Explicitly reset plug events delay back to USB4 spec value
+    - net: usb: qmi_wwan: Add new usb-id for Dell branded EM7455
+    - Input: snvs_pwrkey - fix SNVS_HPVIDR1 register address
+    - can: c_can: don't cache TX messages for C_CAN cores
+    - clk: ingenic-tcu: Properly enable registers before accessing timers
+    - x86/sgx: Do not fail on incomplete sanitization on premature stop of ksgxd
+    - ARM: dts: integrator: Tag PCI host with device_type
+    - ntfs: fix BUG_ON in ntfs_lookup_inode_by_name()
+    - mm/damon/dbgfs: fix memory leak when using debugfs_lookup()
+    - net: mt7531: only do PLL once after the reset
+    - Revert "firmware: arm_scmi: Add clock management to the SCMI power domain"
+    - drm/i915/gt: Restrict forced preemption to the active context
+    - drm/amdgpu: Add amdgpu suspend-resume code path under SRIOV
+    - vduse: prevent uninitialized memory accesses
+    - libata: add ATA_HORKAGE_NOLPM for Pioneer BDR-207M and BDR-205
+    - mmc: moxart: fix 4-bit bus width and remove 8-bit bus width
+    - mmc: hsq: Fix data stomping during mmc recovery
+    - mm/page_alloc: fix race condition between build_all_zonelists and page
+      allocation
+    - mm: prevent page_frag_alloc() from corrupting the memory
+    - mm: fix dereferencing possible ERR_PTR
+    - mm/migrate_device.c: flush TLB while holding PTL
+    - mm: fix madivse_pageout mishandling on non-LRU page
+    - mm,hwpoison: check mm when killing accessing process
+    - media: dvb_vb2: fix possible out of bound access
+    - media: rkvdec: Disable H.264 error detection
+    - media: v4l2-compat-ioctl32.c: zero buffer passed to
+      v4l2_compat_get_array_args()
+    - swiotlb: max mapping size takes min align mask into account
+    - ARM: dts: am33xx: Fix MMCHS0 dma properties
+    - reset: imx7: Fix the iMX8MP PCIe PHY PERST support
+    - ARM: dts: am5748: keep usb4_tm disabled
+    - soc: sunxi: sram: Actually claim SRAM regions
+    - soc: sunxi: sram: Prevent the driver from being unbound
+    - soc: sunxi_sram: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - soc: sunxi: sram: Fix probe function ordering issues
+    - soc: sunxi: sram: Fix debugfs info for A64 SRAM C
+    - ASoC: imx-card: Fix refcount issue with of_node_put
+    - arm64: dts: qcom: sm8350: fix UFS PHY serdes size
+    - ASoC: tas2770: Reinit regcache on reset
+    - drm/bridge: lt8912b: add vsync hsync
+    - drm/bridge: lt8912b: set hdmi or dvi mode
+    - drm/bridge: lt8912b: fix corrupted image output
+    - Revert "drm: bridge: analogix/dp: add panel prepare/unprepare in
+      suspend/resume time"
+    - Input: melfas_mip4 - fix return value check in mip4_probe()
+    - gpio: mvebu: Fix check for pwm support on non-A8K platforms
+    - usbnet: Fix memory leak in usbnet_disconnect()
+    - net: sched: act_ct: fix possible refcount leak in tcf_ct_init()
+    - cxgb4: fix missing unlock on ETHOFLD desc collect fail path
+    - net/mlxbf_gige: Fix an IS_ERR() vs NULL bug in mlxbf_gige_mdio_probe
+    - nvme: Fix IOC_PR_CLEAR and IOC_PR_RELEASE ioctls for nvme devices
+    - wifi: mac80211: fix regression with non-QoS drivers
+    - net: stmmac: power up/down serdes in stmmac_open/release
+    - net: phy: Don't WARN for PHY_UP state in mdio_bus_phy_resume()
+    - selftests: Fix the if conditions of in test_extra_filter()
+    - vdpa/ifcvf: fix the calculation of queuepair
+    - fs: split off setxattr_copy and do_setxattr function from setxattr
+    - clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks
+    - clk: iproc: Do not rely on node name for correct PLL setup
+    - KVM: x86: Hide IA32_PLATFORM_DCA_CAP[31:0] from the guest
+    - x86/alternative: Fix race in try_get_desc()
+    - drm/i915/gem: Really move i915_gem_context.link under ref protection
+    - Linux 5.15.72
+
+  * Jammy update: v5.15.71 upstream stable release (LP: #1995420)
+    - drm/amdgpu: Separate vf2pf work item init from virt data exchange
+    - drm/amdgpu: make sure to init common IP before gmc
+    - staging: r8188eu: Remove support for devices with 8188FU chipset (0bda:f179)
+    - staging: r8188eu: Add Rosewill USB-N150 Nano to device tables
+    - usb: dwc3: gadget: Avoid starting DWC3 gadget during UDC unbind
+    - usb: dwc3: Issue core soft reset before enabling run/stop
+    - usb: dwc3: gadget: Prevent repeat pullup()
+    - usb: dwc3: gadget: Refactor pullup()
+    - usb: dwc3: gadget: Don't modify GEVNTCOUNT in pullup()
+    - usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop
+    - usb: add quirks for Lenovo OneLink+ Dock
+    - usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
+    - Revert "usb: add quirks for Lenovo OneLink+ Dock"
+    - Revert "usb: gadget: udc-xilinx: replace memcpy with memcpy_toio"
+    - drivers/base: Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES
+    - USB: core: Fix RST error in hub.c
+    - USB: serial: option: add Quectel BG95 0x0203 composition
+    - USB: serial: option: add Quectel RM520N
+    - ALSA: core: Fix double-free at snd_card_new()
+    - ALSA: hda/tegra: set depop delay for tegra
+    - ALSA: hda: add Intel 5 Series / 3400 PCI DID
+    - ALSA: hda/realtek: Add quirk for Huawei WRT-WX9
+    - ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5570 laptop
+    - ALSA: hda/realtek: Re-arrange quirk table entries
+    - ALSA: hda/realtek: Add pincfg for ASUS G513 HP jack
+    - ALSA: hda/realtek: Add pincfg for ASUS G533Z HP jack
+    - ALSA: hda/realtek: Add quirk for ASUS GA503R laptop
+    - ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5530 laptop
+    - iommu/vt-d: Check correct capability for sagaw determination
+    - btrfs: fix hang during unmount when stopping block group reclaim worker
+    - btrfs: fix hang during unmount when stopping a space reclaim worker
+    - media: flexcop-usb: fix endpoint type check
+    - usb: dwc3: core: leave default DMA if the controller does not support 64-bit
+      DMA
+    - efi: x86: Wipe setup_data on pure EFI boot
+    - efi: libstub: check Shim mode using MokSBStateRT
+    - wifi: mt76: fix reading current per-tid starting sequence number for
+      aggregation
+    - gpio: mockup: fix NULL pointer dereference when removing debugfs
+    - gpio: mockup: Fix potential resource leakage when register a chip
+    - gpiolib: cdev: Set lineevent_state::irq after IRQ register successfully
+    - riscv: fix a nasty sigreturn bug...
+    - kasan: call kasan_malloc() from __kmalloc_*track_caller()
+    - can: flexcan: flexcan_mailbox_read() fix return value for drop = true
+    - net: mana: Add rmb after checking owner bits
+    - mm/slub: fix to return errno if kmalloc() fails
+    - mm: slub: fix flush_cpu_slab()/__free_slab() invocations in task context.
+    - KVM: x86: Inject #UD on emulated XSETBV if XSAVES isn't enabled
+    - arm64: topology: fix possible overflow in amu_fie_setup()
+    - vmlinux.lds.h: CFI: Reduce alignment of jump-table to function alignment
+    - xfs: reorder iunlink remove operation in xfs_ifree
+    - xfs: fix xfs_ifree() error handling to not leak perag ref
+    - xfs: validate inode fork size against fork format
+    - firmware: arm_scmi: Harden accesses to the reset domains
+    - firmware: arm_scmi: Fix the asynchronous reset requests
+    - arm64: dts: rockchip: Pull up wlan wake# on Gru-Bob
+    - arm64: dts: rockchip: Fix typo in lisense text for PX30.Core
+    - drm/mediatek: dsi: Add atomic {destroy,duplicate}_state, reset callbacks
+    - arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
+    - dmaengine: ti: k3-udma-private: Fix refcount leak bug in of_xudma_dev_get()
+    - arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
+    - netfilter: nf_conntrack_sip: fix ct_sip_walk_headers
+    - netfilter: nf_conntrack_irc: Tighten matching on DCC message
+    - netfilter: nfnetlink_osf: fix possible bogus match in nf_osf_find()
+    - ice: Don't double unplug aux on peer initiated reset
+    - iavf: Fix cached head and tail value for iavf_get_tx_pending
+    - ipvlan: Fix out-of-bound bugs caused by unset skb->mac_header
+    - net: core: fix flow symmetric hash
+    - net: phy: aquantia: wait for the suspend/resume operations to finish
+    - scsi: qla2xxx: Fix memory leak in __qlt_24xx_handle_abts()
+    - scsi: mpt3sas: Fix return value check of dma_get_required_mask()
+    - net: bonding: Share lacpdu_mcast_addr definition
+    - net: bonding: Unsync device addresses on ndo_stop
+    - net: team: Unsync device addresses on ndo_stop
+    - drm/panel: simple: Fix innolux_g121i1_l01 bus_format
+    - MIPS: lantiq: export clk_get_io() for lantiq_wdt.ko
+    - MIPS: Loongson32: Fix PHY-mode being left unspecified
+    - um: fix default console kernel parameter
+    - iavf: Fix bad page state
+    - mlxbf_gige: clear MDIO gateway lock after read
+    - i40e: Fix set max_tx_rate when it is lower than 1 Mbps
+    - sfc: fix TX channel offset when using legacy interrupts
+    - sfc: fix null pointer dereference in efx_hard_start_xmit
+    - drm/hisilicon/hibmc: Allow to be built if COMPILE_TEST is enabled
+    - drm/hisilicon: Add depends on MMU
+    - of: mdio: Add of_node_put() when breaking out of for_each_xx
+    - net: ipa: properly limit modem routing table use
+    - wireguard: ratelimiter: disable timings test by default
+    - wireguard: netlink: avoid variable-sized memcpy on sockaddr
+    - net: enetc: move enetc_set_psfp() out of the common enetc_set_features()
+    - net: enetc: deny offload of tc-based TSN features on VF interfaces
+    - net/sched: taprio: avoid disabling offload when it was never enabled
+    - net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo child
+      qdiscs
+    - netfilter: nf_tables: fix nft_counters_enabled underflow at
+      nf_tables_addchain()
+    - netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
+    - netfilter: ebtables: fix memory leak when blob is malformed
+    - net: ravb: Fix PHY state warning splat during system resume
+    - net: sh_eth: Fix PHY state warning splat during system resume
+    - can: gs_usb: gs_can_open(): fix race dev->can.state condition
+    - perf stat: Fix BPF program section name
+    - perf jit: Include program header in ELF files
+    - perf kcore_copy: Do not check /proc/modules is unchanged
+    - perf tools: Honor namespace when synthesizing build-ids
+    - drm/mediatek: dsi: Move mtk_dsi_stop() call back to mtk_dsi_poweroff()
+    - net/smc: Stop the CLC flow if no link to map buffers on
+    - bonding: fix NULL deref in bond_rr_gen_slave_id
+    - net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD
+    - net: sched: fix possible refcount leak in tc_new_tfilter()
+    - bnxt: prevent skb UAF after handing over to PTP worker
+    - selftests: forwarding: add shebang for sch_red.sh
+    - KVM: x86/mmu: Fold rmap_recycle into rmap_add
+    - serial: fsl_lpuart: Reset prior to registration
+    - serial: Create uart_xmit_advance()
+    - serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
+    - serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
+    - s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup
+    - drm/amd/amdgpu: fixing read wrong pf2vf data in SRIOV
+    - Drivers: hv: Never allocate anything besides framebuffer from framebuffer
+      memory region
+    - drm/gma500: Fix BUG: sleeping function called from invalid context errors
+    - drm/amd/pm: disable BACO entry/exit completely on several sienna cichlid
+      cards
+    - drm/amdgpu: use dirty framebuffer helper
+    - drm/amd/display: Limit user regamma to a valid value
+    - drm/amd/display: Reduce number of arguments of dml31's
+      CalculateWatermarksAndDRAMSpeedChangeSupport()
+    - drm/amd/display: Reduce number of arguments of dml31's
+      CalculateFlipSchedule()
+    - drm/amd/display: Mark dml30's UseMinimumDCFCLK() as noinline for stack usage
+    - drm/rockchip: Fix return type of cdn_dp_connector_mode_valid
+    - fsdax: Fix infinite loop in dax_iomap_rw()
+    - workqueue: don't skip lockdep work dependency in cancel_work_sync()
+    - i2c: imx: If pm_runtime_get_sync() returned 1 device access is possible
+    - i2c: mlxbf: incorrect base address passed during io write
+    - i2c: mlxbf: prevent stack overflow in mlxbf_i2c_smbus_start_transaction()
+    - i2c: mlxbf: Fix frequency calculation
+    - drm/amdgpu: don't register a dirty callback for non-atomic
+    - NFSv4: Fixes for nfs4_inode_return_delegation()
+    - devdax: Fix soft-reservation memory description
+    - ext4: make directory inode spreading reflect flexbg size
+    - ext4: fix bug in extents parsing when eh_entries == 0 and eh_depth > 0
+    - ext4: limit the number of retries after discarding preallocations blocks
+    - ext4: make mballoc try target group first even with mb_optimize_scan
+    - ext4: avoid unnecessary spreading of allocations among groups
+    - ext4: use locality group preallocation for small closed files
+    - Linux 5.15.71
+    - Revert "drm/amdgpu: use dirty framebuffer helper"
+
+  * Jammy update: v5.15.70 upstream stable release (LP: #1995415)
+    - drm/tegra: vic: Fix build warning when CONFIG_PM=n
+    - serial: atmel: remove redundant assignment in rs485_config
+    - tty: serial: atmel: Preserve previous USART mode if RS485 disabled
+    - of: fdt: fix off-by-one error in unflatten_dt_nodes()
+    - pinctrl: qcom: sc8180x: Fix gpio_wakeirq_map
+    - pinctrl: qcom: sc8180x: Fix wrong pin numbers
+    - pinctrl: rockchip: Enhance support for IRQ_TYPE_EDGE_BOTH
+    - pinctrl: sunxi: Fix name for A100 R_PIO
+    - NFSv4: Turn off open-by-filehandle and NFS re-export for NFSv4.0
+    - gpio: mpc8xxx: Fix support for IRQ_TYPE_LEVEL_LOW flow_type in mpc85xx
+    - drm/meson: Correct OSD1 global alpha value
+    - drm/meson: Fix OSD1 RGB to YCbCr coefficient
+    - block: blk_queue_enter() / __bio_queue_enter() must return -EAGAIN for
+      nowait
+    - parisc: ccio-dma: Add missing iounmap in error path in ccio_probe()
+    - of/device: Fix up of_dma_configure_id() stub
+    - cifs: revalidate mapping when doing direct writes
+    - cifs: don't send down the destination address to sendmsg for a SOCK_STREAM
+    - cifs: always initialize struct msghdr smb_msg completely
+    - parisc: Allow CONFIG_64BIT with ARCH=parisc
+    - tools/include/uapi: Fix <asm/errno.h> for parisc and xtensa
+    - drm/amdgpu: Don't enable LTR if not supported
+    - drm/amdgpu: move nbio ih_doorbell_range() into ih code for vega
+    - drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega
+    - binder: remove inaccurate mmap_assert_locked()
+    - arm64: dts: juno: Add missing MHU secure-irq
+    - ASoC: nau8824: Fix semaphore unbalance at error paths
+    - regulator: pfuze100: Fix the global-out-of-bounds access in
+      pfuze100_regulator_probe()
+    - scsi: lpfc: Return DID_TRANSPORT_DISRUPTED instead of DID_REQUEUE
+    - rxrpc: Fix local destruction being repeated
+    - rxrpc: Fix calc of resend age
+    - wifi: mac80211_hwsim: check length for virtio packets
+    - ALSA: hda/sigmatel: Keep power up while beep is enabled
+    - ALSA: hda/tegra: Align BDL entry to 4KB boundary
+    - net: usb: qmi_wwan: add Quectel RM520N
+    - afs: Return -EAGAIN, not -EREMOTEIO, when a file already locked
+    - MIPS: OCTEON: irq: Fix octeon_irq_force_ciu_mapping()
+    - drm/panfrost: devfreq: set opp to the recommended one to configure regulator
+    - mksysmap: Fix the mismatch of 'L0' symbols in System.map
+    - video: fbdev: pxa3xx-gcu: Fix integer overflow in pxa3xx_gcu_write
+    - net: Find dst with sk's xfrm policy not ctl_sk
+    - KVM: SEV: add cache flush to solve SEV cache incoherency issues
+    - cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all()
+    - ALSA: hda/sigmatel: Fix unused variable warning for beep power change
+    - Linux 5.15.70
+
+  * Jammy update: v5.15.69 upstream stable release (LP: #1993010)
+    - NFS: Fix WARN_ON due to unionization of nfs_inode.nrequests
+    - ACPI: resource: skip IRQ override on AMD Zen platforms
+    - ARM: dts: imx: align SPI NOR node name with dtschema
+    - ARM: dts: imx6qdl-kontron-samx6i: fix spi-flash compatible
+    - ARM: dts: at91: fix low limit for CPU regulator
+    - ARM: dts: at91: sama7g5ek: specify proper regulator output ranges
+    - lockdep: Fix -Wunused-parameter for _THIS_IP_
+    - x86/mm: Force-inline __phys_addr_nodebug()
+    - task_stack, x86/cea: Force-inline stack helpers
+    - tracing: hold caller_addr to hardirq_{enable,disable}_ip
+    - tracefs: Only clobber mode/uid/gid on remount if asked
+    - iommu/vt-d: Fix kdump kernels boot failure with scalable mode
+    - Input: goodix - add support for GT1158
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Go 2
+    - drm/msm/rd: Fix FIFO-full deadlock
+    - dt-bindings: iio: gyroscope: bosch,bmg160: correct number of pins
+    - HID: ishtp-hid-clientHID: ishtp-hid-client: Fix comment typo
+    - hid: intel-ish-hid: ishtp: Fix ishtp client sending disordered message
+    - tg3: Disable tg3 device on system reboot to avoid triggering AER
+    - gpio: mockup: remove gpio debugfs when remove device
+    - ieee802154: cc2520: add rc code in cc2520_tx()
+    - Input: iforce - add support for Boeder Force Feedback Wheel
+    - nvmet-tcp: fix unhandled tcp states in nvmet_tcp_state_change()
+    - drm/amd/amdgpu: skip ucode loading if ucode_size == 0
+    - net: dsa: hellcreek: Print warning only once
+    - perf/arm_pmu_platform: fix tests for platform_get_irq() failure
+    - platform/x86: acer-wmi: Acer Aspire One AOD270/Packard Bell Dot keymap fixes
+    - usb: storage: Add ASUS <0x0b05:0x1932> to IGNORE_UAS
+    - mm: Fix TLB flush for not-first PFNMAP mappings in unmap_region()
+    - soc: fsl: select FSL_GUTS driver for DPIO
+    - usb: gadget: f_uac2: clean up some inconsistent indenting
+    - usb: gadget: f_uac2: fix superspeed transfer
+    - RDMA/irdma: Use s/g array in post send only when its valid
+    - Input: goodix - add compatible string for GT1158
+    - Linux 5.15.69
+
+  * Jammy update: v5.15.68 upstream stable release (LP: #1993003)
+    - net: wwan: iosm: remove pointless null check
+    - efi: libstub: Disable struct randomization
+    - efi: capsule-loader: Fix use-after-free in efi_capsule_write
+    - wifi: iwlegacy: 4965: corrected fix for potential off-by-one overflow in
+      il4965_rs_fill_link_cmd()
+    - fs: only do a memory barrier for the first set_buffer_uptodate()
+    - Revert "mm: kmemleak: take a full lowmem check in kmemleak_*_phys()"
+    - scsi: qla2xxx: Disable ATIO interrupt coalesce for quad port ISP27XX
+    - scsi: megaraid_sas: Fix double kfree()
+    - drm/gem: Fix GEM handle release errors
+    - drm/amdgpu: Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
+      psp_hw_fini
+    - drm/amdgpu: Check num_gfx_rings for gfx v9_0 rb setup.
+    - drm/radeon: add a force flush to delay work when radeon
+    - scsi: ufs: core: Reduce the power mode change timeout
+    - Revert "parisc: Show error if wrong 32/64-bit compiler is being used"
+    - parisc: ccio-dma: Handle kmalloc failure in ccio_init_resources()
+    - parisc: Add runtime check to prevent PA2.0 kernels on PA1.x machines
+    - arm64: cacheinfo: Fix incorrect assignment of signed error value to unsigned
+      fw_level
+    - netfilter: conntrack: work around exceeded receive window
+    - cpufreq: check only freq_table in __resolve_freq()
+    - net/core/skbuff: Check the return value of skb_copy_bits()
+    - md: Flush workqueue md_rdev_misc_wq in md_alloc()
+    - fbdev: fbcon: Destroy mutex on freeing struct fb_info
+    - fbdev: chipsfb: Add missing pci_disable_device() in chipsfb_pci_init()
+    - drm/amdgpu: mmVM_L2_CNTL3 register not initialized correctly
+    - ALSA: pcm: oss: Fix race at SNDCTL_DSP_SYNC
+    - ALSA: emu10k1: Fix out of bounds access in snd_emu10k1_pcm_channel_alloc()
+    - ALSA: aloop: Fix random zeros in capture data when using jiffies timer
+    - ALSA: usb-audio: Fix an out-of-bounds bug in
+      __snd_usb_parse_audio_interface()
+    - tracing: Fix to check event_mutex is held while accessing trigger list
+    - btrfs: zoned: set pseudo max append zone limit in zone emulation mode
+    - vfio/type1: Unpin zero pages
+    - kprobes: Prohibit probes in gate area
+    - debugfs: add debugfs_lookup_and_remove()
+    - sched/debug: fix dentry leak in update_sched_domain_debugfs
+    - drm/amd/display: fix memory leak when using debugfs_lookup()
+    - nvmet: fix a use-after-free
+    - scsi: mpt3sas: Fix use-after-free warning
+    - scsi: lpfc: Add missing destroy_workqueue() in error path
+    - NFS: Further optimisations for 'ls -l'
+    - NFS: Save some space in the inode
+    - NFS: Fix another fsync() issue after a server reboot
+    - cgroup: Elide write-locking threadgroup_rwsem when updating csses on an
+      empty subtree
+    - cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock
+    - ASoC: qcom: sm8250: add missing module owner
+    - RDMA/rtrs-clt: Use the right sg_cnt after ib_dma_map_sg
+    - RDMA/rtrs-srv: Pass the correct number of entries for dma mapped SGL
+    - ARM: dts: imx6qdl-kontron-samx6i: remove duplicated node
+    - soc: imx: gpcv2: Assert reset before ungating clock
+    - regulator: core: Clean up on enable failure
+    - tee: fix compiler warning in tee_shm_register()
+    - RDMA/cma: Fix arguments order in net device validation
+    - soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugs
+    - RDMA/hns: Fix supported page size
+    - RDMA/hns: Fix wrong fixed value of qp->rq.wqe_shift
+    - wifi: wilc1000: fix DMA on stack objects
+    - ARM: at91: pm: fix self-refresh for sama7g5
+    - ARM: at91: pm: fix DDR recalibration when resuming from backup and self-
+      refresh
+    - ARM: dts: at91: sama5d27_wlsom1: specify proper regulator output ranges
+    - ARM: dts: at91: sama5d2_icp: specify proper regulator output ranges
+    - ARM: dts: at91: sama5d27_wlsom1: don't keep ldo2 enabled all the time
+    - ARM: dts: at91: sama5d2_icp: don't keep vdd_other enabled all the time
+    - netfilter: br_netfilter: Drop dst references before setting.
+    - netfilter: nf_tables: clean up hook list when offload flags check fails
+    - RDMA/srp: Set scmnd->result only when scmnd is not NULL
+    - ALSA: usb-audio: Inform the delayed registration more properly
+    - ALSA: usb-audio: Register card again for iface over delayed_register option
+    - rxrpc: Fix ICMP/ICMP6 error handling
+    - rxrpc: Fix an insufficiently large sglist in rxkad_verify_packet_2()
+    - afs: Use the operation issue time instead of the reply time for callbacks
+    - Revert "net: phy: meson-gxl: improve link-up behavior"
+    - sch_sfb: Don't assume the skb is still around after enqueueing to child
+    - tipc: fix shift wrapping bug in map_get()
+    - net: introduce __skb_fill_page_desc_noacc
+    - tcp: TX zerocopy should not sense pfmemalloc status
+    - ice: use bitmap_free instead of devm_kfree
+    - i40e: Fix kernel crash during module removal
+    - iavf: Detach device during reset task
+    - xen-netback: only remove 'hotplug-status' when the vif is actually destroyed
+    - RDMA/siw: Pass a pointer to virt_to_page()
+    - ipv6: sr: fix out-of-bounds read when setting HMAC data.
+    - IB/core: Fix a nested dead lock as part of ODP flow
+    - RDMA/mlx5: Set local port to one when accessing counters
+    - erofs: fix pcluster use-after-free on UP platforms
+    - nvme-tcp: fix UAF when detecting digest errors
+    - nvme-tcp: fix regression that causes sporadic requests to time out
+    - tcp: fix early ETIMEDOUT after spurious non-SACK RTO
+    - nvmet: fix mar and mor off-by-one errors
+    - RDMA/irdma: Report the correct max cqes from query device
+    - RDMA/irdma: Return correct WC error for bind operation failure
+    - RDMA/irdma: Report RNR NAK generation in device caps
+    - sch_sfb: Also store skb len before calling child enqueue
+    - perf script: Fix Cannot print 'iregs' field for hybrid systems
+    - hwmon: (tps23861) fix byte order in resistance register
+    - ASoC: mchp-spdiftx: remove references to mchp_i2s_caps
+    - ASoC: mchp-spdiftx: Fix clang -Wbitfield-constant-conversion
+    - MIPS: loongson32: ls1c: Fix hang during startup
+    - kbuild: disable header exports for UML in a straightforward way
+    - i40e: Refactor tc mqprio checks
+    - i40e: Fix ADQ rate limiting for PF
+    - swiotlb: avoid potential left shift overflow
+    - iommu/amd: use full 64-bit value in build_completion_wait()
+    - s390/boot: fix absolute zero lowcore corruption on boot
+    - hwmon: (mr75203) fix VM sensor allocation when "intel,vm-map" not defined
+    - hwmon: (mr75203) update pvt->v_num and vm_num to the actual number of used
+      sensors
+    - hwmon: (mr75203) fix voltage equation for negative source input
+    - hwmon: (mr75203) fix multi-channel voltage reading
+    - hwmon: (mr75203) enable polling for all VM channels
+    - arm64/bti: Disable in kernel BTI when cross section thunks are broken
+    - [Config] updateconfigs for ARM64_BTI_KERNEL
+    - iommu/vt-d: Correctly calculate sagaw value of IOMMU
+    - [Config] updateconfigs for ARM64_ERRATUM_2457168
+    - arm64: errata: add detection for AMEVCNTR01 incrementing incorrectly
+    - drm/bridge: display-connector: implement bus fmts callbacks
+    - perf machine: Use path__join() to compose a path instead of snprintf(dir,
+      '/', filename)
+    - ARM: at91: ddr: remove CONFIG_SOC_SAMA7 dependency
+    - Linux 5.15.68
+
+  * Jammy update: v5.15.67 upstream stable release (LP: #1991841)
+    - Linux 5.15.67
+
+  * Jammy update: v5.15.66 upstream stable release (LP: #1991840)
+    - drm/msm/dsi: fix the inconsistent indenting
+    - drm/msm/dp: delete DP_RECOVERED_CLOCK_OUT_EN to fix tps4
+    - drm/msm/dsi: Fix number of regulators for msm8996_dsi_cfg
+    - drm/msm/dsi: Fix number of regulators for SDM660
+    - platform/x86: pmc_atom: Fix SLP_TYPx bitfield mask
+    - iio: adc: mcp3911: make use of the sign bit
+    - skmsg: Fix wrong last sg check in sk_msg_recvmsg()
+    - bpf: Restrict bpf_sys_bpf to CAP_PERFMON
+    - bpf, cgroup: Fix kernel BUG in purge_effective_progs
+    - ieee802154/adf7242: defer destroy_workqueue call
+    - drm/i915/backlight: extract backlight code to a separate file
+    - drm/i915/display: avoid warnings when registering dual panel backlight
+    - ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
+    - ALSA: hda: intel-nhlt: Correct the handling of fmt_config flexible array
+    - wifi: cfg80211: debugfs: fix return type in ht40allow_map_read()
+    - Revert "xhci: turn off port power in shutdown"
+    - net: sparx5: fix handling uneven length packets in manual extraction
+    - net: smsc911x: Stop and start PHY during suspend and resume
+    - openvswitch: fix memory leak at failed datapath creation
+    - net: dsa: xrs700x: Use irqsave variant for u64 stats update
+    - net: sched: tbf: don't call qdisc_put() while holding tree lock
+    - net/sched: fix netdevice reference leaks in attach_default_qdiscs()
+    - ethernet: rocker: fix sleep in atomic context bug in neigh_timer_handler
+    - mlxbf_gige: compute MDIO period based on i1clk
+    - kcm: fix strp_init() order and cleanup
+    - sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb
+    - tcp: annotate data-race around challenge_timestamp
+    - Revert "sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb"
+    - net/smc: Remove redundant refcount increase
+    - soundwire: qcom: fix device status array range
+    - serial: fsl_lpuart: RS485 RTS polariy is inverse
+    - staging: rtl8712: fix use after free bugs
+    - staging: r8188eu: add firmware dependency
+    - powerpc: align syscall table for ppc32
+    - vt: Clear selection before changing the font
+    - musb: fix USB_MUSB_TUSB6010 dependency
+    - tty: serial: lpuart: disable flow control while waiting for the transmit
+      engine to complete
+    - Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
+    - iio: ad7292: Prevent regulator double disable
+    - iio: adc: mcp3911: use correct formula for AD conversion
+    - misc: fastrpc: fix memory corruption on probe
+    - misc: fastrpc: fix memory corruption on open
+    - USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
+    - mmc: core: Fix UHS-I SD 1.8V workaround branch
+    - mmc: core: Fix inconsistent sd3_bus_mode at UHS-I SD voltage switch failure
+    - binder: fix UAF of ref->proc caused by race condition
+    - binder: fix alloc->vma_vm_mm null-ptr dereference
+    - cifs: fix small mempool leak in SMB2_negotiate()
+    - KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
+    - drm/i915/reg: Fix spelling mistake "Unsupport" -> "Unsupported"
+    - clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops
+    - Revert "clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops"
+    - clk: core: Fix runtime PM sequence in clk_core_unprepare()
+    - Input: rk805-pwrkey - fix module autoloading
+    - clk: bcm: rpi: Fix error handling of raspberrypi_fw_get_rate
+    - clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()
+    - clk: bcm: rpi: Prevent out-of-bounds access
+    - clk: bcm: rpi: Add missing newline
+    - hwmon: (gpio-fan) Fix array out of bounds access
+    - gpio: pca953x: Add mutex_lock for regcache sync in PM
+    - KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
+    - xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
+    - mm: pagewalk: Fix race between unmap and page walker
+    - xen-blkback: Advertise feature-persistent as user requested
+    - xen-blkfront: Advertise feature-persistent as user requested
+    - xen-blkfront: Cache feature_persistent value before advertisement
+    - thunderbolt: Use the actual buffer in tb_async_error()
+    - usb: dwc3: pci: Add support for Intel Raptor Lake
+    - media: mceusb: Use new usb_control_msg_*() routines
+    - xhci: Add grace period after xHC start to prevent premature runtime suspend.
+    - USB: serial: cp210x: add Decagon UCA device id
+    - USB: serial: option: add support for OPPO R11 diag port
+    - USB: serial: option: add Quectel EM060K modem
+    - USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
+    - usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles
+    - usb: typec: intel_pmc_mux: Add new ACPI ID for Meteor Lake IOM device
+    - usb: typec: tcpm: Return ENOTSUPP for power supply prop writes
+    - usb: dwc2: fix wrong order of phy_power_on and phy_init
+    - usb: cdns3: fix issue with rearming ISO OUT endpoint
+    - usb: cdns3: fix incorrect handling TRB_SMM flag for ISOC transfer
+    - USB: cdc-acm: Add Icom PMR F3400 support (0c26:0020)
+    - usb-storage: Add ignore-residue quirk for NXP PN7462AU
+    - s390/hugetlb: fix prepare_hugepage_range() check for 2 GB hugepages
+    - s390: fix nospec table alignments
+    - USB: core: Prevent nested device-reset calls
+    - usb: xhci-mtk: relax TT periodic bandwidth allocation
+    - usb: xhci-mtk: fix bandwidth release issue
+    - usb: gadget: mass_storage: Fix cdrom data transfers on MAC-OS
+    - driver core: Don't probe devices after bus_type.match() probe deferral
+    - wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected
+    - wifi: mac80211: Fix UAF in ieee80211_scan_rx()
+    - net: Use u64_stats_fetch_begin_irq() for stats fetch.
+    - net: mac802154: Fix a condition in the receive path
+    - ALSA: hda/realtek: Add speaker AMP init for Samsung laptops with ALC298
+    - ALSA: seq: oss: Fix data-race for max_midi_devs access
+    - ALSA: seq: Fix data-race at module auto-loading
+    - drm/i915/glk: ECS Liva Q2 needs GLK HDMI port timing quirk
+    - drm/i915: Skip wm/ddb readout for disabled pipes
+    - tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()
+    - kbuild: Add skip_encoding_btf_enum64 option to pahole
+    - usb: dwc3: fix PHY disable sequence
+    - usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup
+    - usb: dwc3: disable USB core PHY management
+    - USB: serial: ch341: fix lost character on LCR updates
+    - USB: serial: ch341: fix disabled rx timer on older devices
+    - Linux 5.15.66
+
+  * Jammy update: v5.15.65 upstream stable release (LP: #1991831)
+    - mm: Force TLB flush for PFNMAP mappings before unlink_file_vma()
+    - drm/bridge: Add stubs for devm_drm_of_get_bridge when OF is disabled
+    - ACPI: thermal: drop an always true check
+    - drm/vc4: hdmi: Rework power up
+    - drm/vc4: hdmi: Depends on CONFIG_PM
+    - firmware: tegra: bpmp: Do only aligned access to IPC memory area
+    - crypto: lib - remove unneeded selection of XOR_BLOCKS
+    - Drivers: hv: balloon: Support status report for larger page sizes
+    - mm/hugetlb: avoid corrupting page->mapping in hugetlb_mcopy_atomic_pte
+    - [Config] updateconfigs for ARM64_ERRATUM_2441009
+    - arm64: errata: Add Cortex-A510 to the repeat tlbi list
+    - io_uring: Remove unused function req_ref_put
+    - kbuild: Fix include path in scripts/Makefile.modpost
+    - Bluetooth: L2CAP: Fix build errors in some archs
+    - HID: steam: Prevent NULL pointer dereference in steam_{recv,send}_report
+    - udmabuf: Set the DMA mask for the udmabuf device (v2)
+    - media: pvrusb2: fix memory leak in pvr_probe
+    - HID: hidraw: fix memory leak in hidraw_release()
+    - net: fix refcount bug in sk_psock_get (2)
+    - fbdev: fb_pm2fb: Avoid potential divide by zero error
+    - ftrace: Fix NULL pointer dereference in is_ftrace_trampoline when ftrace is
+      dead
+    - bpf: Don't redirect packets with invalid pkt_len
+    - ALSA: usb-audio: Add quirk for LH Labs Geek Out HD Audio 1V5
+    - HID: add Lenovo Yoga C630 battery quirk
+    - HID: AMD_SFH: Add a DMI quirk entry for Chromebooks
+    - HID: asus: ROG NKey: Ignore portion of 0x5a report
+    - HID: thrustmaster: Add sparco wheel and fix array length
+    - drm/i915/gt: Skip TLB invalidations once wedged
+    - mmc: mtk-sd: Clear interrupts when cqe off/disable
+    - mmc: sdhci-of-dwcmshc: add reset call back for rockchip Socs
+    - mmc: sdhci-of-dwcmshc: rename rk3568 to rk35xx
+    - mmc: sdhci-of-dwcmshc: Re-enable support for the BlueField-3 SoC
+    - btrfs: remove root argument from btrfs_unlink_inode()
+    - btrfs: remove no longer needed logic for replaying directory deletes
+    - btrfs: add and use helper for unlinking inode during log replay
+    - btrfs: fix warning during log replay when bumping inode link count
+    - fs/ntfs3: Fix work with fragmented xattr
+    - ASoC: sh: rz-ssi: Improve error handling in rz_ssi_probe() error path
+    - drm/amd/display: Avoid MPC infinite loop
+    - drm/amd/display: Fix HDMI VSIF V3 incorrect issue
+    - drm/amd/display: For stereo keep "FLIP_ANY_FRAME"
+    - drm/amd/display: clear optc underflow before turn off odm clock
+    - ksmbd: return STATUS_BAD_NETWORK_NAME error status if share is not
+      configured
+    - neigh: fix possible DoS due to net iface start/stop loop
+    - s390/hypfs: avoid error message under KVM
+    - ksmbd: don't remove dos attribute xattr on O_TRUNC open
+    - drm/amd/pm: add missing ->fini_microcode interface for Sienna Cichlid
+    - drm/amd/display: Fix pixel clock programming
+    - drm/amdgpu: Increase tlb flush timeout for sriov
+    - drm/amd/display: avoid doing vm_init multiple time
+    - netfilter: conntrack: NF_CONNTRACK_PROCFS should no longer default to y
+    - testing: selftests: nft_flowtable.sh: use random netns names
+    - btrfs: move lockdep class helpers to locking.c
+    - btrfs: fix lockdep splat with reloc root extent buffers
+    - btrfs: tree-checker: check for overlapping extent items
+    - kprobes: don't call disarm_kprobe() for disabled kprobes
+    - btrfs: fix space cache corruption and potential double allocations
+    - android: binder: fix lockdep check on clearing vma
+    - net/af_packet: check len when min_header_len equals to 0
+    - net: neigh: don't call kfree_skb() under spin_lock_irqsave()
+    - Linux 5.15.65
+
+  * CVE-2022-2663
+    - netfilter: nf_conntrack_irc: Fix forged IP logic
+
+  * CVE-2022-3061
+    - video: fbdev: i740fb: Error out if 'pixclock' equals zero
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Thu, 24 Nov 2022 14:06:05 +0100
+
+linux (5.15.0-56.62) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-56.62 -proposed tracker (LP: #1997079)
+
+  * CVE-2022-3566
+    - tcp: Fix data races around icsk->icsk_af_ops.
+
+  * CVE-2022-3567
+    - ipv6: annotate some data-races around sk->sk_prot
+    - ipv6: Fix data races around sk->sk_prot.
+
+  * CVE-2022-3621
+    - nilfs2: fix NULL pointer dereference at nilfs_bmap_lookup_at_level()
+
+  * CVE-2022-3564
+    - Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
+
+  * CVE-2022-3524
+    - tcp/udp: Fix memory leak in ipv6_renew_options().
+
+  * CVE-2022-3565
+    - mISDN: fix use-after-free bugs in l1oip timer handlers
+
+  * CVE-2022-3594
+    - r8152: Rate limit overflow messages
+
+  * CVE-2022-43945
+    - SUNRPC: Fix svcxdr_init_decode's end-of-buffer calculation
+    - SUNRPC: Fix svcxdr_init_encode's buflen calculation
+    - NFSD: Protect against send buffer overflow in NFSv2 READDIR
+    - NFSD: Protect against send buffer overflow in NFSv3 READDIR
+    - NFSD: Protect against send buffer overflow in NFSv2 READ
+    - NFSD: Protect against send buffer overflow in NFSv3 READ
+    - NFSD: Remove "inline" directives on op_rsize_bop helpers
+    - NFSD: Cap rsize_bop result based on send buffer size
+
+  * CVE-2022-42703
+    - mm/rmap: Fix anon_vma->degree ambiguity leading to double-reuse
+
+  * 5.15.0-53-generic no longer boots (LP: #1996740)
+    - drm/amd/display: Add helper for blanking all dp displays
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Tue, 22 Nov 2022 12:08:58 -0300
+
+linux (5.15.0-53.59) jammy; urgency=medium
+
+  * Fix blank screen on Thinkpad ADL 4K+ panel (LP: #1980621)
+    - drm/i915: Implement WaEdpLinkRateDataReload
+
+  * Kernel regresses openjdk on riscv64 (LP: #1992484)
+    - SAUCE: Revert "riscv: mmap with PROT_WRITE but no PROT_READ is invalid"
+
+  * iavf: SR-IOV VFs error with no traffic flow when MTU greater than 1500
+    (LP: #1983656)
+    - iavf: Fix set max MTU size with port VLAN and jumbo frames
+    - i40e: Fix VF set max MTU size
+
+  * [Ubuntu 22.04] mpt3sas: Request to include latest bug fix patches
+    (LP: #1965927)
+    - scsi: mpt3sas: Remove scsi_dma_map() error messages
+    - scsi: mpt3sas: Update persistent trigger pages from sysfs interface
+
+  * ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel
+    systems (LP: #1990985)
+    - ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel
+      systems
+
+  * Fix resume on AMD platforms when TBT monitor is plugged (LP: #1990920)
+    - SAUCE: Revert "drm/amd/display: Add helper for blanking all dp displays"
+    - drm/amd/display: Detect dpcd_rev when hotplug mst monitor
+    - drm/amd/display: Release remote dc_sink under mst scenario
+
+  * LSM: Configuring Too Many LSMs Causes Kernel Panic on Boot (LP: #1987998)
+    - SAUCE: LSM: Change Landlock from LSMBLOB_NEEDED to LSMBLOB_NOT_NEEDED
+
+  * To support Intel Maple Ridge Thunderbolt [8086:1134] (LP: #1990240)
+    - thunderbolt: Add support for Intel Maple Ridge single port controller
+
+  * Intel graphic driver is not probing[8086:468b] (LP: #1990242)
+    - drm/i915/adl_s: Update ADL-S PCI IDs
+    - drm/i915: Add new ADL-S pci id
+
+  * Add HDMI codec ID for Intel Raptor Lake (LP: #1989578)
+    - ALSA: hda: Add PCI and HDMI IDs for Intel Raptor Lake
+
+  * Jammy update: v5.15.64 upstream stable release (LP: #1991717)
+    - wifi: rtlwifi: remove always-true condition pointed out by GCC 12
+    - eth: sun: cassini: remove dead code
+    - audit: fix potential double free on error path from fsnotify_add_inode_mark
+    - cgroup: Fix race condition at rebind_subsystems()
+    - parisc: Make CONFIG_64BIT available for ARCH=parisc64 only
+    - parisc: Fix exception handler for fldw and fstw instructions
+    - kernel/sys_ni: add compat entry for fadvise64_64
+    - x86/entry: Move CLD to the start of the idtentry macro
+    - block: add a bdev_max_zone_append_sectors helper
+    - block: add bdev_max_segments() helper
+    - btrfs: zoned: revive max_zone_append_bytes
+    - btrfs: replace BTRFS_MAX_EXTENT_SIZE with fs_info->max_extent_size
+    - btrfs: convert count_max_extents() to use fs_info->max_extent_size
+    - Input: i8042 - move __initconst to fix code styling warning
+    - Input: i8042 - merge quirk tables
+    - Input: i8042 - add TUXEDO devices to i8042 quirk tables
+    - Input: i8042 - add additional TUXEDO devices to i8042 quirk tables
+    - drivers/base: fix userspace break from using bin_attributes for cpumap and
+      cpulist
+    - scsi: qla2xxx: Fix response queue handler reading stale packets
+    - scsi: qla2xxx: edif: Fix dropped IKE message
+    - btrfs: put initial index value of a directory in a constant
+    - btrfs: pass the dentry to btrfs_log_new_name() instead of the inode
+    - btrfs: remove unnecessary parameter delalloc_start for writepage_delalloc()
+    - riscv: lib: uaccess: fold fixups into body
+    - riscv: lib: uaccess: fix CSR_STATUS SR_SUM bit
+    - xfrm: fix refcount leak in __xfrm_policy_check()
+    - xfrm: clone missing x->lastused in xfrm_do_migrate
+    - xfrm: policy: fix metadata dst->dev xmit null pointer dereference
+    - fs: require CAP_SYS_ADMIN in target namespace for idmapped mounts
+    - net: use eth_hw_addr_set() instead of ether_addr_copy()
+    - Revert "net: macsec: update SCI upon MAC address change."
+    - NFS: Don't allocate nfs_fattr on the stack in __nfs42_ssc_open()
+    - NFSv4.2 fix problems with __nfs42_ssc_open
+    - SUNRPC: RPC level errors should set task->tk_rpc_status
+    - mm/smaps: don't access young/dirty bit if pte unpresent
+    - ntfs: fix acl handling
+    - rose: check NULL rose_loopback_neigh->loopback
+    - r8152: fix the units of some registers for RTL8156A
+    - r8152: fix the RX FIFO settings when suspending
+    - nfc: pn533: Fix use-after-free bugs caused by pn532_cmd_timeout
+    - ice: xsk: Force rings to be sized to power of 2
+    - ice: xsk: prohibit usage of non-balanced queue id
+    - net/mlx5e: Properly disable vlan strip on non-UL reps
+    - net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
+    - net/mlx5e: Fix wrong application of the LRO state
+    - net/mlx5e: Fix wrong tc flag used when set hw-tc-offload off
+    - net: ipa: don't assume SMEM is page-aligned
+    - net: phy: Don't WARN for PHY_READY state in mdio_bus_phy_resume()
+    - net: moxa: get rid of asymmetry in DMA mapping/unmapping
+    - bonding: 802.3ad: fix no transmission of LACPDUs
+    - net: ipvtap - add __init/__exit annotations to module init/exit funcs
+    - netfilter: ebtables: reject blobs that don't provide all entry points
+    - bnxt_en: fix NQ resource accounting during vf creation on 57500 chips
+    - netfilter: nf_tables: disallow updates of implicit chain
+    - netfilter: nf_tables: make table handle allocation per-netns friendly
+    - netfilter: nft_payload: report ERANGE for too long offset and length
+    - netfilter: nft_payload: do not truncate csum_offset and csum_type
+    - netfilter: nf_tables: do not leave chain stats enabled on error
+    - netfilter: nft_osf: restrict osf to ipv4, ipv6 and inet families
+    - netfilter: nft_tunnel: restrict it to netdev family
+    - netfilter: nf_tables: consolidate rule verdict trace call
+    - netfilter: nft_cmp: optimize comparison for 16-bytes
+    - netfilter: bitwise: improve error goto labels
+    - netfilter: nf_tables: upfront validation of data via nft_data_init()
+    - netfilter: nf_tables: disallow jump to implicit chain from set element
+    - netfilter: nf_tables: disallow binding to already bound chain
+    - netfilter: flowtable: add function to invoke garbage collection immediately
+    - netfilter: flowtable: fix stuck flows on cleanup due to pending work
+    - net: Fix data-races around sysctl_[rw]mem_(max|default).
+    - net: Fix data-races around weight_p and dev_weight_[rt]x_bias.
+    - net: Fix data-races around netdev_max_backlog.
+    - net: Fix data-races around netdev_tstamp_prequeue.
+    - ratelimit: Fix data-races in ___ratelimit().
+    - net: Fix data-races around sysctl_optmem_max.
+    - net: Fix a data-race around sysctl_tstamp_allow_data.
+    - net: Fix a data-race around sysctl_net_busy_poll.
+    - net: Fix a data-race around sysctl_net_busy_read.
+    - net: Fix a data-race around netdev_budget.
+    - tcp: expose the tcp_mark_push() and tcp_skb_entail() helpers
+    - mptcp: stop relying on tcp_tx_skb_cache
+    - net: Fix data-races around sysctl_max_skb_frags.
+    - net: Fix a data-race around netdev_budget_usecs.
+    - net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
+    - net: Fix data-races around sysctl_devconf_inherit_init_net.
+    - net: Fix a data-race around sysctl_somaxconn.
+    - ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
+    - i40e: Fix incorrect address type for IPv6 flow rules
+    - rxrpc: Fix locking in rxrpc's sendmsg
+    - ionic: widen queue_lock use around lif init and deinit
+    - ionic: clear broken state on generation change
+    - ionic: fix up issues with handling EAGAIN on FW cmds
+    - ionic: VF initial random MAC address if no assigned mac
+    - net: stmmac: work around sporadic tx issue on link-up
+    - btrfs: fix silent failure when deleting root reference
+    - btrfs: replace: drop assert for suspended replace
+    - btrfs: add info when mount fails due to stale replace target
+    - btrfs: check if root is readonly while setting security xattr
+    - btrfs: fix possible memory leak in btrfs_get_dev_args_from_path()
+    - perf/x86/lbr: Enable the branch type for the Arch LBR by default
+    - x86/unwind/orc: Unwind ftrace trampolines with correct ORC entry
+    - x86/bugs: Add "unknown" reporting for MMIO Stale Data
+    - x86/nospec: Unwreck the RSB stuffing
+    - loop: Check for overflow while configuring loop
+    - writeback: avoid use-after-free after removing device
+    - asm-generic: sections: refactor memory_intersects
+    - mm/damon/dbgfs: avoid duplicate context directory creation
+    - s390/mm: do not trigger write fault when vma does not allow VM_WRITE
+    - bootmem: remove the vmemmap pages from kmemleak in put_page_bootmem
+    - s390: fix double free of GS and RI CBs on fork() failure
+    - fbdev: fbcon: Properly revert changes when vc_resize() failed
+    - Revert "memcg: cleanup racy sum avoidance code"
+    - ACPI: processor: Remove freq Qos request for all CPUs
+    - nouveau: explicitly wait on the fence in nouveau_bo_move_m2mf
+    - smb3: missing inode locks in punch hole
+    - xen/privcmd: fix error exit of privcmd_ioctl_dm_op()
+    - riscv: traps: add missing prototype
+    - io_uring: fix issue with io_write() not always undoing sb_start_write()
+    - mm/hugetlb: fix hugetlb not supporting softdirty tracking
+    - md: call __md_stop_writes in md_stop
+    - mptcp: Fix crash due to tcp_tsorted_anchor was initialized before release
+      skb
+    - arm64: Fix match_list for erratum 1286807 on Arm Cortex-A76
+    - binder_alloc: add missing mmap_lock calls when using the VMA
+    - x86/nospec: Fix i386 RSB stuffing
+    - Documentation/ABI: Mention retbleed vulnerability info file for sysfs
+    - blk-mq: fix io hung due to missing commit_rqs
+    - perf python: Fix build when PYTHON_CONFIG is user supplied
+    - perf/x86/intel/uncore: Fix broken read_counter() for SNB IMC PMU
+    - perf/x86/intel/ds: Fix precise store latency handling
+    - perf stat: Clear evsel->reset_group for each stat run
+    - scsi: ufs: core: Enable link lost interrupt
+    - scsi: storvsc: Remove WQ_MEM_RECLAIM from storvsc_error_wq
+    - bpf: Don't use tnum_range on array range checking for poke descriptors
+    - Linux 5.15.64
+
+  * Jammy update: v5.15.63 upstream stable release (LP: #1990564)
+    - ALSA: info: Fix llseek return value when using callback
+    - ALSA: hda/realtek: Add quirk for Clevo NS50PU, NS70PU
+    - KVM: Unconditionally get a ref to /dev/kvm module when creating a VM
+    - x86/mm: Use proper mask when setting PUD mapping
+    - rds: add missing barrier to release_refill
+    - locking/atomic: Make test_and_*_bit() ordered on failure
+    - drm/nouveau: recognise GA103
+    - drm/ttm: Fix dummy res NULL ptr deref bug
+    - drm/amd/display: Check correct bounds for stream encoder instances for
+      DCN303
+    - ata: libata-eh: Add missing command name
+    - mmc: pxamci: Fix another error handling path in pxamci_probe()
+    - mmc: pxamci: Fix an error handling path in pxamci_probe()
+    - mmc: meson-gx: Fix an error handling path in meson_mmc_probe()
+    - btrfs: unset reloc control if transaction commit fails in
+      prepare_to_relocate()
+    - btrfs: reset RO counter on block group if we fail to relocate
+    - btrfs: fix lost error handling when looking up extended ref on log replay
+    - cifs: Fix memory leak on the deferred close
+    - x86/kprobes: Fix JNG/JNLE emulation
+    - tracing/eprobes: Do not allow eprobes to use $stack, or % for regs
+    - tracing/eprobes: Do not hardcode $comm as a string
+    - tracing/eprobes: Have event probes be consistent with kprobes and uprobes
+    - tracing/probes: Have kprobes and uprobes use $COMM too
+    - tracing: Have filter accept "common_cpu" to be consistent
+    - ALSA: usb-audio: More comprehensive mixer map for ASUS ROG Zenith II
+    - dt-bindings: usb: mtk-xhci: Allow wakeup interrupt-names to be optional
+    - can: ems_usb: fix clang's -Wunaligned-access warning
+    - apparmor: fix quiet_denied for file rules
+    - Revert "UBUNTU: SAUCE: apparmor: drop prefixing abs root labels with '='"
+    - apparmor: fix absroot causing audited secids to begin with =
+    - apparmor: Fix failed mount permission check error message
+    - apparmor: fix aa_label_asxprint return check
+    - apparmor: fix setting unconfined mode on a loaded profile
+    - apparmor: fix overlapping attachment computation
+    - apparmor: fix reference count leak in aa_pivotroot()
+    - apparmor: Fix memleak in aa_simple_write_to_buffer()
+    - Documentation: ACPI: EINJ: Fix obsolete example
+    - NFSv4.1: Don't decrease the value of seq_nr_highest_sent
+    - NFSv4.1: Handle NFS4ERR_DELAY replies to OP_SEQUENCE correctly
+    - NFSv4: Fix races in the legacy idmapper upcall
+    - NFSv4.1: RECLAIM_COMPLETE must handle EACCES
+    - NFSv4/pnfs: Fix a use-after-free bug in open
+    - BPF: Fix potential bad pointer dereference in bpf_sys_bpf()
+    - bpf: Don't reinit map value in prealloc_lru_pop
+    - bpf: Acquire map uref in .init_seq_private for array map iterator
+    - bpf: Acquire map uref in .init_seq_private for hash map iterator
+    - bpf: Acquire map uref in .init_seq_private for sock local storage map
+      iterator
+    - bpf: Acquire map uref in .init_seq_private for sock{map,hash} iterator
+    - bpf: Check the validity of max_rdwr_access for sock local storage map
+      iterator
+    - can: mcp251x: Fix race condition on receive interrupt
+    - can: j1939: j1939_session_destroy(): fix memory leak of skbs
+    - net: atlantic: fix aq_vec index out of range error
+    - m68k: coldfire/device.c: protect FLEXCAN blocks
+    - sunrpc: fix expiry of auth creds
+    - SUNRPC: Fix xdr_encode_bool()
+    - SUNRPC: Reinitialise the backchannel request buffers before reuse
+    - virtio_net: fix memory leak inside XPD_TX with mergeable
+    - devlink: Fix use-after-free after a failed reload
+    - net: phy: Warn about incorrect mdio_bus_phy_resume() state
+    - net: bcmgenet: Indicate MAC is in charge of PHY PM
+    - net: bgmac: Fix a BUG triggered by wrong bytes_compl
+    - selftests: forwarding: Fix failing tests with old libnet
+    - dt-bindings: arm: qcom: fix Alcatel OneTouch Idol 3 compatibles
+    - pinctrl: nomadik: Fix refcount leak in nmk_pinctrl_dt_subnode_to_map
+    - pinctrl: qcom: msm8916: Allow CAMSS GP clocks to be muxed
+    - pinctrl: amd: Don't save/restore interrupt status and wake status bits
+    - pinctrl: sunxi: Add I/O bias setting for H6 R-PIO
+    - pinctrl: qcom: sm8250: Fix PDC map
+    - Input: exc3000 - fix return value check of wait_for_completion_timeout
+    - octeontx2-pf: Fix NIX_AF_TL3_TL2X_LINKX_CFG register configuration
+    - octeontx2-af: Apply tx nibble fixup always
+    - octeontx2-af: suppress external profile loading warning
+    - octeontx2-af: Fix mcam entry resource leak
+    - octeontx2-af: Fix key checking for source mac
+    - ACPI: property: Return type of acpi_add_nondev_subnodes() should be bool
+    - geneve: do not use RT_TOS for IPv6 flowlabel
+    - mlx5: do not use RT_TOS for IPv6 flowlabel
+    - ipv6: do not use RT_TOS for IPv6 flowlabel
+    - plip: avoid rcu debug splat
+    - vsock: Fix memory leak in vsock_connect()
+    - vsock: Set socket state back to SS_UNCONNECTED in vsock_connect_timeout()
+    - dt-bindings: gpio: zynq: Add missing compatible strings
+    - dt-bindings: arm: qcom: fix Longcheer L8150 compatibles
+    - dt-bindings: arm: qcom: fix MSM8916 MTP compatibles
+    - dt-bindings: arm: qcom: fix MSM8994 boards compatibles
+    - dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
+    - spi: dt-bindings: cadence: add missing 'required'
+    - spi: dt-bindings: zynqmp-qspi: add missing 'required'
+    - ceph: use correct index when encoding client supported features
+    - tools/vm/slabinfo: use alphabetic order when two values are equal
+    - ceph: don't leak snap_rwsem in handle_cap_grant
+    - kbuild: dummy-tools: avoid tmpdir leak in dummy gcc
+    - tools build: Switch to new openssl API for test-libcrypto
+    - NTB: ntb_tool: uninitialized heap data in tool_fn_write()
+    - nfp: ethtool: fix the display error of `ethtool -m DEVNAME`
+    - xen/xenbus: fix return type in xenbus_file_read()
+    - atm: idt77252: fix use-after-free bugs caused by tst_timer
+    - geneve: fix TOS inheriting for ipv4
+    - perf probe: Fix an error handling path in 'parse_perf_probe_command()'
+    - perf parse-events: Fix segfault when event parser gets an error
+    - perf tests: Fix Track with sched_switch test for hybrid case
+    - dpaa2-eth: trace the allocated address instead of page struct
+    - fs/ntfs3: Fix using uninitialized value n when calling indx_read
+    - fs/ntfs3: Fix NULL deref in ntfs_update_mftmirr
+    - fs/ntfs3: Don't clear upper bits accidentally in log_replay()
+    - fs/ntfs3: Fix double free on remount
+    - fs/ntfs3: Do not change mode if ntfs_set_ea failed
+    - fs/ntfs3: Fix missing i_op in ntfs_read_mft
+    - nios2: page fault et.al. are *not* restartable syscalls...
+    - nios2: don't leave NULLs in sys_call_table[]
+    - nios2: traced syscall does need to check the syscall number
+    - nios2: fix syscall restart checks
+    - nios2: restarts apply only to the first sigframe we build...
+    - nios2: add force_successful_syscall_return()
+    - iavf: Fix adminq error handling
+    - iavf: Fix reset error handling
+    - ASoC: SOF: debug: Fix potential buffer overflow by snprintf()
+    - ASoC: tas2770: Set correct FSYNC polarity
+    - ASoC: tas2770: Allow mono streams
+    - ASoC: tas2770: Drop conflicting set_bias_level power setting
+    - ASoC: tas2770: Fix handling of mute/unmute
+    - ASoC: codec: tlv320aic32x4: fix mono playback via I2S
+    - netfilter: nf_tables: use READ_ONCE and WRITE_ONCE for shared generation id
+      access
+    - fs/ntfs3: uninitialized variable in ntfs_set_acl_ex()
+    - netfilter: nf_tables: disallow NFTA_SET_ELEM_KEY_END with
+      NFT_SET_ELEM_INTERVAL_END flag
+    - netfilter: nf_tables: possible module reference underflow in error path
+    - netfilter: nf_tables: really skip inactive sets when allocating name
+    - netfilter: nf_tables: validate NFTA_SET_ELEM_OBJREF based on NFT_SET_OBJECT
+      flag
+    - netfilter: nf_tables: NFTA_SET_ELEM_KEY_END requires concat and interval
+      flags
+    - netfilter: nf_tables: disallow NFT_SET_ELEM_CATCHALL and
+      NFT_SET_ELEM_INTERVAL_END
+    - netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified
+    - powerpc/pci: Fix get_phb_number() locking
+    - spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
+    - net/sunrpc: fix potential memory leaks in rpc_sysfs_xprt_state_change()
+    - net: dsa: mv88e6060: prevent crash on an unused port
+    - mlxsw: spectrum: Clear PTP configuration after unregistering the netdevice
+    - net: moxa: pass pdev instead of ndev to DMA functions
+    - net: fix potential refcount leak in ndisc_router_discovery()
+    - net: dsa: microchip: ksz9477: fix fdb_dump last invalid entry
+    - net: dsa: felix: fix ethtool 256-511 and 512-1023 TX packet counters
+    - net: genl: fix error path memory leak in policy dumping
+    - net: dsa: don't warn in dsa_port_set_state_now() when driver doesn't support
+      it
+    - net: dsa: sja1105: fix buffer overflow in sja1105_setup_devlink_regions()
+    - ice: Ignore EEXIST when setting promisc mode
+    - i2c: imx: Make sure to unregister adapter on remove()
+    - regulator: pca9450: Remove restrictions for regulator-name
+    - i40e: Fix to stop tx_timeout recovery if GLOBR fails
+    - fec: Fix timer capture timing in `fec_ptp_enable_pps()`
+    - stmmac: intel: Add a missing clk_disable_unprepare() call in
+      intel_eth_pci_remove()
+    - igb: Add lock to avoid data race
+    - kbuild: fix the modules order between drivers and libs
+    - gcc-plugins: Undefine LATENT_ENTROPY_PLUGIN when plugin disabled for a file
+    - tracing/eprobes: Fix reading of string fields
+    - drm/imx/dcss: get rid of HPD warning message
+    - ASoC: SOF: Intel: hda: Define rom_status_reg in sof_intel_dsp_desc
+    - ASoC: SOF: Intel: hda: Fix potential buffer overflow by snprintf()
+    - drm/meson: Fix refcount bugs in meson_vpu_has_available_connectors()
+    - drm/sun4i: dsi: Prevent underflow when computing packet sizes
+    - net: qrtr: start MHI channel after endpoit creation
+    - KVM: arm64: Treat PMCR_EL1.LC as RES1 on asymmetric systems
+    - KVM: arm64: Reject 32bit user PSTATE on asymmetric systems
+    - HID: multitouch: new device class fix Lenovo X12 trackpad sticky
+    - PCI: Add ACS quirk for Broadcom BCM5750x NICs
+    - platform/chrome: cros_ec_proto: don't show MKBP version if unsupported
+    - usb: cdns3 fix use-after-free at workaround 2
+    - usb: cdns3: fix random warning message when driver load
+    - usb: gadget: uvc: calculate the number of request depending on framesize
+    - usb: gadget: uvc: call uvc uvcg_warn on completed status instead of
+      uvcg_info
+    - PCI: aardvark: Fix reporting Slot capabilities on emulated bridge
+    - irqchip/tegra: Fix overflow implicit truncation warnings
+    - drm/meson: Fix overflow implicit truncation warnings
+    - clk: ti: Stop using legacy clkctrl names for omap4 and 5
+    - scsi: ufs: ufs-mediatek: Fix the timing of configuring device regulators
+    - usb: host: ohci-ppc-of: Fix refcount leak bug
+    - usb: renesas: Fix refcount leak bug
+    - usb: dwc2: gadget: remove D+ pull-up while no vbus with usb-role-switch
+    - vboxguest: Do not use devm for irq
+    - clk: qcom: ipq8074: dont disable gcc_sleep_clk_src
+    - uacce: Handle parent device removal or parent driver module rmmod
+    - zram: do not lookup algorithm in backends table
+    - clk: qcom: clk-alpha-pll: fix clk_trion_pll_configure description
+    - scsi: lpfc: Prevent buffer overflow crashes in debugfs with malformed user
+      input
+    - scsi: lpfc: Fix possible memory leak when failing to issue CMF WQE
+    - gadgetfs: ep_io - wait until IRQ finishes
+    - coresight: etm4x: avoid build failure with unrolled loops
+    - habanalabs/gaudi: fix shift out of bounds
+    - habanalabs/gaudi: mask constant value before cast
+    - mmc: tmio: avoid glitches when resetting
+    - pinctrl: intel: Check against matching data instead of ACPI companion
+    - cxl: Fix a memory leak in an error handling path
+    - PCI/ACPI: Guard ARM64-specific mcfg_quirks
+    - um: add "noreboot" command line option for PANIC_TIMEOUT=-1 setups
+    - dmaengine: dw-axi-dmac: do not print NULL LLI during error
+    - dmaengine: dw-axi-dmac: ignore interrupt if no descriptor
+    - RDMA/rxe: Limit the number of calls to each tasklet
+    - csky/kprobe: reclaim insn_slot on kprobe unregistration
+    - selftests/kprobe: Do not test for GRP/ without event failures
+    - dmaengine: sprd: Cleanup in .remove() after pm_runtime_get_sync() failed
+    - openrisc: io: Define iounmap argument as volatile
+    - phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks
+    - md: Notify sysfs sync_completed in md_reap_sync_thread()
+    - nvmet-tcp: fix lockdep complaint on nvmet_tcp_wq flush during queue teardown
+    - drivers:md:fix a potential use-after-free bug
+    - ext4: avoid remove directory when directory is corrupted
+    - ext4: avoid resizing to a partial cluster size
+    - lib/list_debug.c: Detect uninitialized lists
+    - tty: serial: Fix refcount leak bug in ucc_uart.c
+    - KVM: PPC: Book3S HV: Fix "rm_exit" entry in debugfs timings
+    - vfio: Clear the caps->buf to NULL after free
+    - mips: cavium-octeon: Fix missing of_node_put() in octeon2_usb_clocks_start
+    - iommu/io-pgtable-arm-v7s: Add a quirk to allow pgtable PA up to 35bit
+    - modules: Ensure natural alignment for .altinstructions and __bug_table
+      sections
+    - ASoC: rsnd: care default case on rsnd_ssiu_busif_err_irq_ctrl()
+    - riscv: dts: sifive: Add fu740 topology information
+    - riscv: dts: canaan: Add k210 topology information
+    - riscv: mmap with PROT_WRITE but no PROT_READ is invalid
+    - RISC-V: Add fast call path of crash_kexec()
+    - watchdog: export lockup_detector_reconfigure
+    - powerpc/32: Set an IBAT covering up to _einittext during init
+    - powerpc/32: Don't always pass -mcpu=powerpc to the compiler
+    - ovl: warn if trusted xattr creation fails
+    - powerpc/ioda/iommu/debugfs: Generate unique debugfs entries
+    - ALSA: core: Add async signal helpers
+    - ALSA: timer: Use deferred fasync helper
+    - ALSA: control: Use deferred fasync helper
+    - f2fs: fix to avoid use f2fs_bug_on() in f2fs_new_node_page()
+    - f2fs: fix to do sanity check on segment type in build_sit_entries()
+    - smb3: check xattr value length earlier
+    - powerpc/64: Init jump labels before parse_early_param()
+    - venus: pm_helpers: Fix warning in OPP during probe
+    - video: fbdev: i740fb: Check the argument of i740_calc_vclk()
+    - MIPS: tlbex: Explicitly compare _PAGE_NO_EXEC against 0
+    - can: j1939: j1939_sk_queue_activate_next_locked(): replace WARN_ON_ONCE with
+      netdev_warn_once()
+    - scsi: ufs: ufs-mediatek: Fix build error and type mismatch
+    - xfs: flush inodegc workqueue tasks before cancel
+    - xfs: reserve quota for dir expansion when linking/unlinking files
+    - xfs: reserve quota for target dir expansion when renaming files
+    - xfs: remove infinite loop when reserving free block pool
+    - xfs: always succeed at setting the reserve pool size
+    - xfs: fix overfilling of reserve pool
+    - xfs: fix soft lockup via spinning in filestream ag selection loop
+    - xfs: revert "xfs: actually bump warning counts when we send warnings"
+    - xfs: reject crazy array sizes being fed to XFS_IOC_GETBMAP*
+    - Linux 5.15.63
+
+  * Jammy update: v5.15.62 upstream stable release (LP: #1990554)
+    - io_uring: use original request task for inflight tracking
+    - tee: add overflow check in register_shm_helper()
+    - net_sched: cls_route: disallow handle of 0
+    - ksmbd: prevent out of bound read for SMB2_WRITE
+    - ksmbd: fix heap-based overflow in set_ntacl_dacl()
+    - btrfs: only write the sectors in the vertical stripe which has data stripes
+    - btrfs: raid56: don't trust any cached sector in __raid56_parity_recover()
+    - Linux 5.15.62
+
+  * Jammy update: v5.15.61 upstream stable release (LP: #1990162)
+    - Makefile: link with -z noexecstack --no-warn-rwx-segments
+    - x86: link vdso and boot with -z noexecstack --no-warn-rwx-segments
+    - Revert "pNFS: nfs3_set_ds_client should set NFS_CS_NOPING"
+    - scsi: Revert "scsi: qla2xxx: Fix disk failure to rediscover"
+    - pNFS/flexfiles: Report RDMA connection errors to the server
+    - NFSD: Clean up the show_nf_flags() macro
+    - nfsd: eliminate the NFSD_FILE_BREAK_* flags
+    - ALSA: usb-audio: Add quirk for Behringer UMC202HD
+    - ALSA: bcd2000: Fix a UAF bug on the error path of probing
+    - ALSA: hda/realtek: Add quirk for Clevo NV45PZ
+    - ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
+    - wifi: mac80211_hwsim: fix race condition in pending packet
+    - wifi: mac80211_hwsim: add back erroneously removed cast
+    - wifi: mac80211_hwsim: use 32-bit skb cookie
+    - add barriers to buffer_uptodate and set_buffer_uptodate
+    - lockd: detect and reject lock arguments that overflow
+    - HID: hid-input: add Surface Go battery quirk
+    - HID: wacom: Only report rotation for art pen
+    - HID: wacom: Don't register pad_input for touch switch
+    - KVM: nVMX: Snapshot pre-VM-Enter BNDCFGS for !nested_run_pending case
+    - KVM: nVMX: Snapshot pre-VM-Enter DEBUGCTL for !nested_run_pending case
+    - KVM: SVM: Don't BUG if userspace injects an interrupt with GIF=0
+    - KVM: s390: pv: don't present the ecall interrupt twice
+    - KVM: x86: Split kvm_is_valid_cr4() and export only the non-vendor bits
+    - KVM: nVMX: Let userspace set nVMX MSR to any _host_ supported value
+    - KVM: nVMX: Account for KVM reserved CR4 bits in consistency checks
+    - KVM: nVMX: Inject #UD if VMXON is attempted with incompatible CR0/CR4
+    - KVM: x86: Mark TSS busy during LTR emulation _after_ all fault checks
+    - KVM: x86: Set error code to segment selector on LLDT/LTR non-canonical #GP
+    - KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
+    - KVM: x86: Tag kvm_mmu_x86_module_init() with __init
+    - KVM: x86: do not report preemption if the steal time cache is stale
+    - KVM: x86: revalidate steal time cache if MSR value changes
+    - riscv: set default pm_power_off to NULL
+    - ALSA: hda/conexant: Add quirk for LENOVO 20149 Notebook model
+    - ALSA: hda/cirrus - support for iMac 12,1 model
+    - ALSA: hda/realtek: Add quirk for another Asus K42JZ model
+    - ALSA: hda/realtek: Add a quirk for HP OMEN 15 (8786) mute LED
+    - tty: vt: initialize unicode screen buffer
+    - vfs: Check the truncate maximum size in inode_newsize_ok()
+    - fs: Add missing umask strip in vfs_tmpfile
+    - thermal: sysfs: Fix cooling_device_stats_setup() error code path
+    - fbcon: Fix boundary checks for fbcon=vc:n1-n2 parameters
+    - fbcon: Fix accelerated fbdev scrolling while logo is still shown
+    - usbnet: Fix linkwatch use-after-free on disconnect
+    - fix short copy handling in copy_mc_pipe_to_iter()
+    - crypto: ccp - Use kzalloc for sev ioctl interfaces to prevent kernel memory
+      leak
+    - ovl: drop WARN_ON() dentry is NULL in ovl_encode_fh()
+    - parisc: Fix device names in /proc/iomem
+    - parisc: Drop pa_swapper_pg_lock spinlock
+    - parisc: Check the return value of ioremap() in lba_driver_probe()
+    - parisc: io_pgetevents_time64() needs compat syscall in 32-bit compat mode
+    - riscv:uprobe fix SR_SPIE set/clear handling
+    - dt-bindings: riscv: fix SiFive l2-cache's cache-sets
+    - RISC-V: kexec: Fixup use of smp_processor_id() in preemptible context
+    - RISC-V: Fixup get incorrect user mode PC for kernel mode regs
+    - RISC-V: Fixup schedule out issue in machine_crash_shutdown()
+    - RISC-V: Add modules to virtual kernel memory layout dump
+    - rtc: rx8025: fix 12/24 hour mode detection on RX-8035
+    - drm/gem: Properly annotate WW context on drm_gem_lock_reservations() error
+    - drm/shmem-helper: Add missing vunmap on error
+    - drm/vc4: hdmi: Disable audio if dmas property is present but empty
+    - drm/hyperv-drm: Include framebuffer and EDID headers
+    - drm/nouveau: fix another off-by-one in nvbios_addr
+    - drm/nouveau: Don't pm_runtime_put_sync(), only pm_runtime_put_autosuspend()
+    - drm/nouveau/acpi: Don't print error when we get -EINPROGRESS from pm_runtime
+    - drm/nouveau/kms: Fix failure path for creating DP connectors
+    - drm/amdgpu: Check BO's requested pinning domains against its
+      preferred_domains
+    - bpf: Fix KASAN use-after-free Read in compute_effective_progs
+    - btrfs: reject log replay if there is unsupported RO compat flag
+    - mtd: rawnand: arasan: Fix clock rate in NV-DDR
+    - mtd: rawnand: arasan: Update NAND bus clock instead of system clock
+    - um: Remove straying parenthesis
+    - um: seed rng using host OS rng
+    - iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
+    - iio: light: isl29028: Fix the warning in isl29028_remove()
+    - scsi: sg: Allow waiting for commands to complete on removed device
+    - scsi: qla2xxx: Fix incorrect display of max frame size
+    - scsi: qla2xxx: Zero undefined mailbox IN registers
+    - soundwire: qcom: Check device status before reading devid
+    - ksmbd: fix memory leak in smb2_handle_negotiate
+    - ksmbd: prevent out of bound read for SMB2_TREE_CONNNECT
+    - ksmbd: fix use-after-free bug in smb2_tree_disconect
+    - fuse: limit nsec
+    - fuse: ioctl: translate ENOSYS
+    - serial: mvebu-uart: uart2 error bits clearing
+    - md-raid10: fix KASAN warning
+    - mbcache: don't reclaim used entries
+    - mbcache: add functions to delete entry if unused
+    - media: [PATCH] pci: atomisp_cmd: fix three missing checks on list iterator
+    - ia64, processor: fix -Wincompatible-pointer-types in ia64_get_irr()
+    - PCI: Add defines for normal and subtractive PCI bridges
+    - powerpc/fsl-pci: Fix Class Code of PCIe Root Port
+    - powerpc/ptdump: Fix display of RW pages on FSL_BOOK3E
+    - powerpc/powernv: Avoid crashing if rng is NULL
+    - MIPS: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+    - coresight: Clear the connection field properly
+    - usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
+    - USB: HCD: Fix URB giveback issue in tasklet function
+    - ARM: dts: uniphier: Fix USB interrupts for PXs2 SoC
+    - arm64: dts: uniphier: Fix USB interrupts for PXs3 SoC
+    - usb: dwc3: gadget: refactor dwc3_repare_one_trb
+    - usb: dwc3: gadget: fix high speed multiplier setting
+    - netfilter: nf_tables: fix null deref due to zeroed list head
+    - epoll: autoremove wakers even more aggressively
+    - x86: Handle idle=nomwait cmdline properly for x86_idle
+    - arch: make TRACE_IRQFLAGS_NMI_SUPPORT generic
+    - arm64: Do not forget syscall when starting a new thread.
+    - arm64: fix oops in concurrently setting insn_emulation sysctls
+    - ext2: Add more validity checks for inode counts
+    - sched/fair: Introduce SIS_UTIL to search idle CPU based on sum of util_avg
+    - genirq: Don't return error on missing optional irq_request_resources()
+    - irqchip/mips-gic: Only register IPI domain when SMP is enabled
+    - genirq: GENERIC_IRQ_IPI depends on SMP
+    - sched/core: Always flush pending blk_plug
+    - irqchip/mips-gic: Check the return value of ioremap() in gic_of_init()
+    - wait: Fix __wait_event_hrtimeout for RT/DL tasks
+    - ARM: dts: imx6ul: add missing properties for sram
+    - ARM: dts: imx6ul: change operating-points to uint32-matrix
+    - ARM: dts: imx6ul: fix keypad compatible
+    - ARM: dts: imx6ul: fix csi node compatible
+    - ARM: dts: imx6ul: fix lcdif node compatible
+    - ARM: dts: imx6ul: fix qspi node compatible
+    - ARM: dts: BCM5301X: Add DT for Meraki MR26
+    - ARM: dts: ux500: Fix Codina accelerometer mounting matrix
+    - ARM: dts: ux500: Fix Gavini accelerometer mounting matrix
+    - spi: synquacer: Add missing clk_disable_unprepare()
+    - ARM: OMAP2+: display: Fix refcount leak bug
+    - ARM: OMAP2+: pdata-quirks: Fix refcount leak bug
+    - ACPI: EC: Remove duplicate ThinkPad X1 Carbon 6th entry from DMI quirks
+    - ACPI: EC: Drop the EC_FLAGS_IGNORE_DSDT_GPE quirk
+    - ACPI: PM: save NVS memory for Lenovo G40-45
+    - ACPI: LPSS: Fix missing check in register_device_clock()
+    - ARM: dts: qcom: sdx55: Fix the IRQ trigger type for UART
+    - arm64: dts: qcom: ipq8074: fix NAND node name
+    - arm64: dts: allwinner: a64: orangepi-win: Fix LED node name
+    - ARM: shmobile: rcar-gen2: Increase refcount for new reference
+    - firmware: tegra: Fix error check return value of debugfs_create_file()
+    - hwmon: (dell-smm) Add Dell XPS 13 7390 to fan control whitelist
+    - hwmon: (sht15) Fix wrong assumptions in device remove callback
+    - PM: hibernate: defer device probing when resuming from hibernation
+    - selinux: fix memleak in security_read_state_kernel()
+    - selinux: Add boundary check in put_entry()
+    - kasan: test: Silence GCC 12 warnings
+    - drm/amdgpu: Remove one duplicated ef removal
+    - powerpc/64s: Disable stack variable initialisation for prom_init
+    - spi: spi-rspi: Fix PIO fallback on RZ platforms
+    - ARM: findbit: fix overflowing offset
+    - meson-mx-socinfo: Fix refcount leak in meson_mx_socinfo_init
+    - arm64: dts: renesas: beacon: Fix regulator node names
+    - spi: spi-altera-dfl: Fix an error handling path
+    - ARM: bcm: Fix refcount leak in bcm_kona_smc_init
+    - ACPI: processor/idle: Annotate more functions to live in cpuidle section
+    - ARM: dts: imx7d-colibri-emmc: add cpu1 supply
+    - soc: renesas: r8a779a0-sysc: Fix A2DP1 and A2CV[2357] PDR values
+    - scsi: hisi_sas: Use managed PCI functions
+    - dt-bindings: iio: accel: Add DT binding doc for ADXL355
+    - soc: amlogic: Fix refcount leak in meson-secure-pwrc.c
+    - arm64: dts: renesas: Fix thermal-sensors on single-zone sensors
+    - x86/pmem: Fix platform-device leak in error path
+    - ARM: dts: ast2500-evb: fix board compatible
+    - ARM: dts: ast2600-evb: fix board compatible
+    - ARM: dts: ast2600-evb-a1: fix board compatible
+    - arm64: dts: mt8192: Fix idle-states nodes naming scheme
+    - arm64: dts: mt8192: Fix idle-states entry-method
+    - arm64: select TRACE_IRQFLAGS_NMI_SUPPORT
+    - arm64: cpufeature: Allow different PMU versions in ID_DFR0_EL1
+    - locking/lockdep: Fix lockdep_init_map_*() confusion
+    - arm64: dts: qcom: sc7180: Remove ipa_fw_mem node on trogdor
+    - soc: fsl: guts: machine variable might be unset
+    - block: fix infinite loop for invalid zone append
+    - ARM: dts: qcom: mdm9615: add missing PMIC GPIO reg
+    - ARM: OMAP2+: Fix refcount leak in omapdss_init_of
+    - ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
+    - arm64: dts: qcom: sdm630: disable GPU by default
+    - arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
+    - arm64: dts: qcom: sdm630: fix gpu's interconnect path
+    - arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf
+    - cpufreq: zynq: Fix refcount leak in zynq_get_revision
+    - regulator: qcom_smd: Fix pm8916_pldo range
+    - ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP
+    - ARM: dts: qcom-msm8974: fix irq type on blsp2_uart1
+    - soc: qcom: ocmem: Fix refcount leak in of_get_ocmem
+    - soc: qcom: aoss: Fix refcount leak in qmp_cooling_devices_register
+    - ARM: dts: qcom: pm8841: add required thermal-sensor-cells
+    - bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
+    - stack: Declare {randomize_,}kstack_offset to fix Sparse warnings
+    - arm64: dts: qcom: msm8916: Fix typo in pronto remoteproc node
+    - ACPI: APEI: explicit init of HEST and GHES in apci_init()
+    - drivers/iio: Remove all strcpy() uses
+    - ACPI: VIOT: Fix ACS setup
+    - arm64: dts: qcom: sm6125: Move sdc2 pinctrl from seine-pdx201 to sm6125
+    - arm64: dts: qcom: sm6125: Append -state suffix to pinctrl nodes
+    - arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
+    - arm64: dts: mt7622: fix BPI-R64 WPS button
+    - arm64: tegra: Fixup SYSRAM references
+    - arm64: tegra: Update Tegra234 BPMP channel addresses
+    - arm64: tegra: Mark BPMP channels as no-memory-wc
+    - arm64: tegra: Fix SDMMC1 CD on P2888
+    - erofs: avoid consecutive detection for Highmem memory
+    - blk-mq: don't create hctx debugfs dir until q->debugfs_dir is created
+    - spi: Fix simplification of devm_spi_register_controller
+    - spi: tegra20-slink: fix UAF in tegra_slink_remove()
+    - hwmon: (drivetemp) Add module alias
+    - blktrace: Trace remapped requests correctly
+    - PM: domains: Ensure genpd_debugfs_dir exists before remove
+    - dm writecache: return void from functions
+    - dm writecache: count number of blocks read, not number of read bios
+    - dm writecache: count number of blocks written, not number of write bios
+    - dm writecache: count number of blocks discarded, not number of discard bios
+    - regulator: of: Fix refcount leak bug in of_get_regulation_constraints()
+    - soc: qcom: Make QCOM_RPMPD depend on PM
+    - arm64: dts: qcom: qcs404: Fix incorrect USB2 PHYs assignment
+    - irqdomain: Report irq number for NOMAP domains
+    - drivers/perf: arm_spe: Fix consistency of SYS_PMSCR_EL1.CX
+    - nohz/full, sched/rt: Fix missed tick-reenabling bug in dequeue_task_rt()
+    - x86/extable: Fix ex_handler_msr() print condition
+    - selftests/seccomp: Fix compile warning when CC=clang
+    - thermal/tools/tmon: Include pthread and time headers in tmon.h
+    - dm: return early from dm_pr_call() if DM device is suspended
+    - pwm: sifive: Simplify offset calculation for PWMCMP registers
+    - pwm: sifive: Ensure the clk is enabled exactly once per running PWM
+    - pwm: sifive: Shut down hardware only after pwmchip_remove() completed
+    - pwm: lpc18xx-sct: Reduce number of devm memory allocations
+    - pwm: lpc18xx-sct: Simplify driver by not using pwm_[gs]et_chip_data()
+    - pwm: lpc18xx: Fix period handling
+    - drm/dp: Export symbol / kerneldoc fixes for DP AUX bus
+    - drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated
+      function
+    - ath10k: do not enforce interrupt trigger type
+    - drm/st7735r: Fix module autoloading for Okaya RH128128T
+    - drm/panel: Fix build error when CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y &&
+      CONFIG_DRM_DISPLAY_HELPER=m
+    - wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
+    - ath11k: fix netdev open race
+    - drm/mipi-dbi: align max_chunk to 2 in spi_transfer
+    - ath11k: Fix incorrect debug_mask mappings
+    - drm/radeon: fix potential buffer overflow in ni_set_mc_special_registers()
+    - drm/mediatek: Modify dsi funcs to atomic operations
+    - drm/mediatek: Separate poweron/poweroff from enable/disable and define new
+      funcs
+    - drm/mediatek: Add pull-down MIPI operation in mtk_dsi_poweroff function
+    - drm/meson: encoder_hdmi: switch to bridge DRM_BRIDGE_ATTACH_NO_CONNECTOR
+    - drm/meson: encoder_hdmi: Fix refcount leak in meson_encoder_hdmi_init
+    - drm/bridge: lt9611uxc: Cancel only driver's work
+    - i2c: npcm: Remove own slave addresses 2:10
+    - i2c: npcm: Correct slave role behavior
+    - i2c: mxs: Silence a clang warning
+    - virtio-gpu: fix a missing check to avoid NULL dereference
+    - drm/shmem-helper: Unexport drm_gem_shmem_create_with_handle()
+    - drm/shmem-helper: Export dedicated wrappers for GEM object functions
+    - drm/shmem-helper: Pass GEM shmem object in public interfaces
+    - drm/virtio: Fix NULL vs IS_ERR checking in virtio_gpu_object_shmem_init
+    - drm: adv7511: override i2c address of cec before accessing it
+    - crypto: sun8i-ss - do not allocate memory when handling hash requests
+    - crypto: sun8i-ss - fix error codes in allocate_flows()
+    - net: fix sk_wmem_schedule() and sk_rmem_schedule() errors
+    - can: netlink: allow configuring of fixed bit rates without need for
+      do_set_bittiming callback
+    - can: netlink: allow configuring of fixed data bit rates without need for
+      do_set_data_bittiming callback
+    - i2c: Fix a potential use after free
+    - crypto: sun8i-ss - fix infinite loop in sun8i_ss_setup_ivs()
+    - media: atmel: atmel-sama7g5-isc: fix warning in configs without OF
+    - media: tw686x: Register the irq at the end of probe
+    - media: imx-jpeg: Correct some definition according specification
+    - media: imx-jpeg: Leave a blank space before the configuration data
+    - media: imx-jpeg: Add pm-runtime support for imx-jpeg
+    - media: imx-jpeg: use NV12M to represent non contiguous NV12
+    - media: imx-jpeg: Set V4L2_BUF_FLAG_LAST at eos
+    - media: imx-jpeg: Refactor function mxc_jpeg_parse
+    - media: imx-jpeg: Identify and handle precision correctly
+    - media: imx-jpeg: Handle source change in a function
+    - media: imx-jpeg: Support dynamic resolution change
+    - media: imx-jpeg: Align upwards buffer size
+    - media: imx-jpeg: Implement drain using v4l2-mem2mem helpers
+    - wifi: iwlegacy: 4965: fix potential off-by-one overflow in
+      il4965_rs_fill_link_cmd()
+    - drm/radeon: fix incorrrect SPDX-License-Identifiers
+    - rcutorture: Warn on individual rcu_torture_init() error conditions
+    - rcutorture: Don't cpuhp_remove_state() if cpuhp_setup_state() failed
+    - rcutorture: Fix ksoftirqd boosting timing and iteration
+    - test_bpf: fix incorrect netdev features
+    - crypto: ccp - During shutdown, check SEV data pointer before using
+    - drm: bridge: adv7511: Add check for mipi_dsi_driver_register
+    - media: imx-jpeg: Disable slot interrupt when frame done
+    - drm/mcde: Fix refcount leak in mcde_dsi_bind
+    - media: hdpvr: fix error value returns in hdpvr_read
+    - media: v4l2-mem2mem: prevent pollerr when last_buffer_dequeued is set
+    - media: driver/nxp/imx-jpeg: fix a unexpected return value problem
+    - media: tw686x: Fix memory leak in tw686x_video_init
+    - drm/vc4: plane: Remove subpixel positioning check
+    - drm/vc4: plane: Fix margin calculations for the right/bottom edges
+    - drm/bridge: Add a function to abstract away panels
+    - drm/vc4: dsi: Switch to devm_drm_of_get_bridge
+    - drm/vc4: Use of_device_get_match_data()
+    - drm/vc4: dsi: Release workaround buffer and DMA
+    - drm/vc4: dsi: Correct DSI divider calculations
+    - drm/vc4: dsi: Correct pixel order for DSI0
+    - drm/vc4: dsi: Register dsi0 as the correct vc4 encoder type
+    - drm/vc4: dsi: Fix dsi0 interrupt support
+    - drm/vc4: dsi: Add correct stop condition to vc4_dsi_encoder_disable
+      iteration
+    - drm/vc4: hdmi: Fix HPD GPIO detection
+    - drm/vc4: hdmi: Avoid full hdmi audio fifo writes
+    - drm/vc4: hdmi: Reset HDMI MISC_CONTROL register
+    - drm/vc4: hdmi: Fix timings for interlaced modes
+    - drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes
+    - crypto: arm64/gcm - Select AEAD for GHASH_ARM64_CE
+    - selftests/xsk: Destroy BPF resources only when ctx refcount drops to 0
+    - drm/rockchip: vop: Don't crash for invalid duplicate_state()
+    - drm/rockchip: Fix an error handling path rockchip_dp_probe()
+    - drm/mediatek: dpi: Remove output format of YUV
+    - drm/mediatek: dpi: Only enable dpi after the bridge is enabled
+    - drm: bridge: sii8620: fix possible off-by-one
+    - hinic: Use the bitmap API when applicable
+    - net: hinic: fix bug that ethtool get wrong stats
+    - net: hinic: avoid kernel hung in hinic_get_stats64()
+    - drm/msm/mdp5: Fix global state lock backoff
+    - crypto: hisilicon/sec - don't sleep when in softirq
+    - crypto: hisilicon - Kunpeng916 crypto driver don't sleep when in softirq
+    - media: platform: mtk-mdp: Fix mdp_ipi_comm structure alignment
+    - drm/msm: Avoid dirtyfb stalls on video mode displays (v2)
+    - drm/msm/dpu: Fix for non-visible planes
+    - mt76: mt76x02u: fix possible memory leak in __mt76x02u_mcu_send_msg
+    - mt76: mt7615: do not update pm stats in case of error
+    - ieee80211: add EHT 1K aggregation definitions
+    - mt76: mt7921: fix aggregation subframes setting to HE max
+    - mt76: mt7921: enlarge maximum VHT MPDU length to 11454
+    - mediatek: mt76: mac80211: Fix missing of_node_put() in mt76_led_init()
+    - mediatek: mt76: eeprom: fix missing of_node_put() in
+      mt76_find_power_limits_node()
+    - skmsg: Fix invalid last sg check in sk_msg_recvmsg()
+    - drm/exynos/exynos7_drm_decon: free resources when clk_set_parent() failed.
+    - tcp: make retransmitted SKB fit into the send window
+    - libbpf: Fix the name of a reused map
+    - selftests: timers: valid-adjtimex: build fix for newer toolchains
+    - selftests: timers: clocksource-switch: fix passing errors from child
+    - bpf: Fix subprog names in stack traces.
+    - fs: check FMODE_LSEEK to control internal pipe splicing
+    - media: cedrus: h265: Fix flag name
+    - media: hantro: postproc: Fix motion vector space size
+    - media: hantro: Simplify postprocessor
+    - media: hevc: Embedded indexes in RPS
+    - media: staging: media: hantro: Fix typos
+    - wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()
+    - wifi: p54: Fix an error handling path in p54spi_probe()
+    - wifi: p54: add missing parentheses in p54_flush()
+    - selftests/bpf: fix a test for snprintf() overflow
+    - libbpf: fix an snprintf() overflow check
+    - can: pch_can: do not report txerr and rxerr during bus-off
+    - can: rcar_can: do not report txerr and rxerr during bus-off
+    - can: sja1000: do not report txerr and rxerr during bus-off
+    - can: hi311x: do not report txerr and rxerr during bus-off
+    - can: sun4i_can: do not report txerr and rxerr during bus-off
+    - can: kvaser_usb_hydra: do not report txerr and rxerr during bus-off
+    - can: kvaser_usb_leaf: do not report txerr and rxerr during bus-off
+    - can: usb_8dev: do not report txerr and rxerr during bus-off
+    - can: error: specify the values of data[5..7] of CAN error frames
+    - can: pch_can: pch_can_error(): initialize errc before using it
+    - Bluetooth: hci_intel: Add check for platform_driver_register
+    - i2c: cadence: Support PEC for SMBus block read
+    - i2c: mux-gpmux: Add of_node_put() when breaking out of loop
+    - wifi: wil6210: debugfs: fix uninitialized variable use in
+      `wil_write_file_wmi()`
+    - wifi: iwlwifi: mvm: fix double list_add at iwl_mvm_mac_wake_tx_queue
+    - wifi: libertas: Fix possible refcount leak in if_usb_probe()
+    - media: cedrus: hevc: Add check for invalid timestamp
+    - net/mlx5e: Remove WARN_ON when trying to offload an unsupported TLS
+      cipher/version
+    - net/mlx5e: Fix the value of MLX5E_MAX_RQ_NUM_MTTS
+    - net/mlx5: Adjust log_max_qp to be 18 at most
+    - crypto: hisilicon/hpre - don't use GFP_KERNEL to alloc mem during softirq
+    - crypto: inside-secure - Add missing MODULE_DEVICE_TABLE for of
+    - crypto: hisilicon/sec - fix auth key size error
+    - inet: add READ_ONCE(sk->sk_bound_dev_if) in INET_MATCH()
+    - ipv6: add READ_ONCE(sk->sk_bound_dev_if) in INET6_MATCH()
+    - net: allow unbound socket for packets in VRF when tcp_l3mdev_accept set
+    - netdevsim: fib: Fix reference count leak on route deletion failure
+    - wifi: rtw88: check the return value of alloc_workqueue()
+    - iavf: Fix max_rate limiting
+    - iavf: Fix 'tc qdisc show' listing too many queues
+    - netdevsim: Avoid allocation warnings triggered from user space
+    - net: rose: fix netdev reference changes
+    - net: ionic: fix error check for vlan flags in ionic_set_nic_features()
+    - dccp: put dccp_qpolicy_full() and dccp_qpolicy_push() in the same lock
+    - net: usb: make USB_RTL8153_ECM non user configurable
+    - wireguard: ratelimiter: use hrtimer in selftest
+    - wireguard: allowedips: don't corrupt stack when detecting overflow
+    - HID: amd_sfh: Don't show client init failed as error when discovery fails
+    - clk: renesas: r9a06g032: Fix UART clkgrp bitsel
+    - mtd: maps: Fix refcount leak in of_flash_probe_versatile
+    - mtd: maps: Fix refcount leak in ap_flash_init
+    - mtd: rawnand: meson: Fix a potential double free issue
+    - of: check previous kernel's ima-kexec-buffer against memory bounds
+    - scsi: qla2xxx: edif: Reduce Initiator-Initiator thrashing
+    - scsi: qla2xxx: edif: Fix potential stuck session in sa update
+    - scsi: qla2xxx: edif: Reduce connection thrash
+    - scsi: qla2xxx: edif: Fix inconsistent check of db_flags
+    - scsi: qla2xxx: edif: Synchronize NPIV deletion with authentication
+      application
+    - scsi: qla2xxx: edif: Add retry for ELS passthrough
+    - scsi: qla2xxx: edif: Fix n2n discovery issue with secure target
+    - scsi: qla2xxx: edif: Fix n2n login retry for secure device
+    - KVM: SVM: Unwind "speculative" RIP advancement if INTn injection "fails"
+    - KVM: SVM: Stuff next_rip on emulated INT3 injection if NRIPS is supported
+    - phy: samsung: exynosautov9-ufs: correct TSRV register configurations
+    - PCI: microchip: Fix refcount leak in mc_pcie_init_irq_domains()
+    - PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
+    - HID: cp2112: prevent a buffer overflow in cp2112_xfer()
+    - mtd: sm_ftl: Fix deadlock caused by cancel_work_sync in sm_release
+    - mtd: partitions: Fix refcount leak in parse_redboot_of
+    - mtd: parsers: ofpart: Fix refcount leak in bcm4908_partitions_fw_offset
+    - mtd: st_spi_fsm: Add a clk_disable_unprepare() in .probe()'s error path
+    - PCI: mediatek-gen3: Fix refcount leak in mtk_pcie_init_irq_domains()
+    - fpga: altera-pr-ip: fix unsigned comparison with less than zero
+    - usb: host: Fix refcount leak in ehci_hcd_ppc_of_probe
+    - usb: ohci-nxp: Fix refcount leak in ohci_hcd_nxp_probe
+    - usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()
+    - usb: xhci: tegra: Fix error check
+    - netfilter: xtables: Bring SPDX identifier back
+    - scsi: qla2xxx: edif: Send LOGO for unexpected IKE message
+    - scsi: qla2xxx: edif: Reduce disruption due to multiple app start
+    - scsi: qla2xxx: edif: Fix no login after app start
+    - scsi: qla2xxx: edif: Tear down session if keys have been removed
+    - scsi: qla2xxx: edif: Fix session thrash
+    - scsi: qla2xxx: edif: Fix no logout on delete for N2N
+    - iio: accel: bma400: Fix the scale min and max macro values
+    - platform/chrome: cros_ec: Always expose last resume result
+    - iio: accel: bma400: Reordering of header files
+    - clk: mediatek: reset: Fix written reset bit offset
+    - lib/test_hmm: avoid accessing uninitialized pages
+    - memremap: remove support for external pgmap refcounts
+    - mm/memremap: fix memunmap_pages() race with get_dev_pagemap()
+    - KVM: Don't set Accessed/Dirty bits for ZERO_PAGE
+    - mwifiex: Ignore BTCOEX events from the 88W8897 firmware
+    - mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv
+    - scsi: iscsi: Allow iscsi_if_stop_conn() to be called from kernel
+    - scsi: iscsi: Add helper to remove a session from the kernel
+    - scsi: iscsi: Fix session removal on shutdown
+    - dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics
+    - mtd: dataflash: Add SPI ID table
+    - clk: qcom: camcc-sm8250: Fix halt on boot by reducing driver's init level
+    - misc: rtsx: Fix an error handling path in rtsx_pci_probe()
+    - driver core: fix potential deadlock in __driver_attach
+    - clk: qcom: clk-krait: unlock spin after mux completion
+    - clk: qcom: gcc-msm8939: Add missing SYSTEM_MM_NOC_BFDCD_CLK_SRC
+    - clk: qcom: gcc-msm8939: Fix bimc_ddr_clk_src rcgr base address
+    - clk: qcom: gcc-msm8939: Add missing system_mm_noc_bfdcd_clk_src
+    - clk: qcom: gcc-msm8939: Point MM peripherals to system_mm_noc clock
+    - usb: host: xhci: use snprintf() in xhci_decode_trb()
+    - RDMA/rxe: Fix deadlock in rxe_do_local_ops()
+    - clk: qcom: ipq8074: fix NSS core PLL-s
+    - clk: qcom: ipq8074: SW workaround for UBI32 PLL lock
+    - clk: qcom: ipq8074: fix NSS port frequency tables
+    - clk: qcom: ipq8074: set BRANCH_HALT_DELAY flag for UBI clocks
+    - clk: qcom: camcc-sdm845: Fix topology around titan_top power domain
+    - clk: qcom: camcc-sm8250: Fix topology around titan_top power domain
+    - clk: qcom: clk-rcg2: Fail Duty-Cycle configuration if MND divider is not
+      enabled.
+    - clk: qcom: clk-rcg2: Make sure to not write d=0 to the NMD register
+    - mm/mempolicy: fix get_nodes out of bound access
+    - PCI: dwc: Stop link on host_init errors and de-initialization
+    - PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
+    - PCI: dwc: Disable outbound windows only for controllers using iATU
+    - PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
+    - PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
+    - PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
+    - soundwire: bus_type: fix remove and shutdown support
+    - soundwire: revisit driver bind/unbind and callbacks
+    - KVM: arm64: Don't return from void function
+    - dmaengine: sf-pdma: Add multithread support for a DMA channel
+    - PCI: endpoint: Don't stop controller when unbinding endpoint function
+    - scsi: qla2xxx: Check correct variable in qla24xx_async_gffid()
+    - intel_th: Fix a resource leak in an error handling path
+    - intel_th: msu-sink: Potential dereference of null pointer
+    - intel_th: msu: Fix vmalloced buffers
+    - binder: fix redefinition of seq_file attributes
+    - staging: rtl8192u: Fix sleep in atomic context bug in
+      dm_fsync_timer_callback
+    - mmc: sdhci-of-esdhc: Fix refcount leak in esdhc_signal_voltage_switch
+    - mmc: mxcmmc: Silence a clang warning
+    - mmc: renesas_sdhi: Get the reset handle early in the probe
+    - memstick/ms_block: Fix some incorrect memory allocation
+    - memstick/ms_block: Fix a memory leak
+    - mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
+    - of: device: Fix missing of_node_put() in of_dma_set_restricted_buffer
+    - mmc: block: Add single read for 4k sector cards
+    - KVM: s390: pv: leak the topmost page table when destroy fails
+    - PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
+    - scsi: smartpqi: Fix DMA direction for RAID requests
+    - xtensa: iss/network: provide release() callback
+    - xtensa: iss: fix handling error cases in iss_net_configure()
+    - usb: gadget: udc: amd5536 depends on HAS_DMA
+    - usb: aspeed-vhub: Fix refcount leak bug in ast_vhub_init_desc()
+    - usb: dwc3: core: Deprecate GCTL.CORESOFTRESET
+    - usb: dwc3: core: Do not perform GCTL_CORE_SOFTRESET during bootup
+    - usb: dwc3: qcom: fix missing optional irq warnings
+    - eeprom: idt_89hpesx: uninitialized data in idt_dbgfs_csr_write()
+    - phy: stm32: fix error return in stm32_usbphyc_phy_init
+    - interconnect: imx: fix max_node_id
+    - um: random: Don't initialise hwrng struct with zero
+    - RDMA/irdma: Fix a window for use-after-free
+    - RDMA/irdma: Fix VLAN connection with wildcard address
+    - RDMA/irdma: Fix setting of QP context err_rq_idx_valid field
+    - RDMA/rtrs-srv: Fix modinfo output for stringify
+    - RDMA/rtrs: Fix warning when use poll mode on client side.
+    - RDMA/rtrs: Replace duplicate check with is_pollqueue helper
+    - RDMA/rtrs: Introduce destroy_cq helper
+    - RDMA/rtrs: Do not allow sessname to contain special symbols / and .
+    - RDMA/rtrs: Rename rtrs_sess to rtrs_path
+    - RDMA/rtrs-srv: Rename rtrs_srv_sess to rtrs_srv_path
+    - RDMA/rtrs-clt: Rename rtrs_clt_sess to rtrs_clt_path
+    - RDMA/rtrs-clt: Replace list_next_or_null_rr_rcu with an inline function
+    - RDMA/qedr: Fix potential memory leak in __qedr_alloc_mr()
+    - RDMA/hns: Fix incorrect clearing of interrupt status register
+    - RDMA/siw: Fix duplicated reported IW_CM_EVENT_CONNECT_REPLY event
+    - iio: cros: Register FIFO callback after sensor is registered
+    - clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
+    - RDMA/hfi1: fix potential memory leak in setup_base_ctxt()
+    - gpio: gpiolib-of: Fix refcount bugs in of_mm_gpiochip_add_data()
+    - HID: mcp2221: prevent a buffer overflow in mcp_smbus_write()
+    - HID: amd_sfh: Add NULL check for hid device
+    - dmaengine: imx-dma: Cast of_device_get_match_data() with (uintptr_t)
+    - scripts/gdb: lx-dmesg: read records individually
+    - scripts/gdb: fix 'lx-dmesg' on 32 bits arch
+    - RDMA/rxe: Fix mw bind to allow any consumer key portion
+    - mmc: cavium-octeon: Add of_node_put() when breaking out of loop
+    - mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
+    - HID: alps: Declare U1_UNICORN_LEGACY support
+    - RDMA/rxe: For invalidate compare according to set keys in mr
+    - PCI: tegra194: Fix Root Port interrupt handling
+    - PCI: tegra194: Fix link up retry sequence
+    - HID: amd_sfh: Handle condition of "no sensors"
+    - USB: serial: fix tty-port initialized comments
+    - usb: cdns3: change place of 'priv_ep' assignment in
+      cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
+    - mtd: spi-nor: fix spi_nor_spimem_setup_op() call in
+      spi_nor_erase_{sector,chip}()
+    - KVM: nVMX: Set UMIP bit CR4_FIXED1 MSR when emulating UMIP
+    - platform/olpc: Fix uninitialized data in debugfs write
+    - RDMA/srpt: Duplicate port name members
+    - RDMA/srpt: Introduce a reference count in struct srpt_device
+    - RDMA/srpt: Fix a use-after-free
+    - android: binder: stop saving a pointer to the VMA
+    - mm/mmap.c: fix missing call to vm_unacct_memory in mmap_region
+    - selftests: kvm: set rax before vmcall
+    - of/fdt: declared return type does not match actual return type
+    - RDMA/mlx5: Add missing check for return value in get namespace flow
+    - RDMA/rxe: Add memory barriers to kernel queues
+    - RDMA/rxe: Remove the is_user members of struct rxe_sq/rxe_rq/rxe_srq
+    - RDMA/rxe: Fix error unwind in rxe_create_qp()
+    - block/rnbd-srv: Set keep_id to true after mutex_trylock
+    - null_blk: fix ida error handling in null_add_dev()
+    - nvme: use command_id instead of req->tag in trace_nvme_complete_rq()
+    - nvme: define compat_ioctl again to unbreak 32-bit userspace.
+    - nvme: disable namespace access for unsupported metadata
+    - nvme: don't return an error from nvme_configure_metadata
+    - nvme: catch -ENODEV from nvme_revalidate_zones again
+    - block/bio: remove duplicate append pages code
+    - block: ensure iov_iter advances for added pages
+    - jbd2: fix outstanding credits assert in jbd2_journal_commit_transaction()
+    - ext4: recover csum seed of tmp_inode after migrating to extents
+    - jbd2: fix assertion 'jh->b_frozen_data == NULL' failure when journal aborted
+    - usb: cdns3: Don't use priv_dev uninitialized in cdns3_gadget_ep_enable()
+    - opp: Fix error check in dev_pm_opp_attach_genpd()
+    - ASoC: cros_ec_codec: Fix refcount leak in cros_ec_codec_platform_probe
+    - ASoC: samsung: Fix error handling in aries_audio_probe
+    - ASoC: imx-audmux: Silence a clang warning
+    - ASoC: mediatek: mt8173: Fix refcount leak in mt8173_rt5650_rt5676_dev_probe
+    - ASoC: mt6797-mt6351: Fix refcount leak in mt6797_mt6351_dev_probe
+    - ASoC: codecs: da7210: add check for i2c_add_driver
+    - ASoC: mediatek: mt8173-rt5650: Fix refcount leak in mt8173_rt5650_dev_probe
+    - serial: 8250: Export ICR access helpers for internal use
+    - serial: 8250: dma: Allow driver operations before starting DMA transfers
+    - serial: 8250_dw: Store LSR into lsr_saved_flags in dw8250_tx_wait_empty()
+    - ASoC: codecs: msm8916-wcd-digital: move gains from SX_TLV to S8_TLV
+    - ASoC: codecs: wcd9335: move gains from SX_TLV to S8_TLV
+    - rpmsg: char: Add mutex protection for rpmsg_eptdev_open()
+    - rpmsg: mtk_rpmsg: Fix circular locking dependency
+    - remoteproc: k3-r5: Fix refcount leak in k3_r5_cluster_of_init
+    - selftests/livepatch: better synchronize test_klp_callbacks_busy
+    - profiling: fix shift too large makes kernel panic
+    - remoteproc: imx_rproc: Fix refcount leak in imx_rproc_addr_init
+    - ASoC: samsung: h1940_uda1380: include proepr GPIO consumer header
+    - powerpc/perf: Optimize clearing the pending PMI and remove WARN_ON for PMI
+      check in power_pmu_disable
+    - ASoC: samsung: change gpiod_speaker_power and rx1950_audio from global to
+      static variables
+    - tty: n_gsm: Delete gsmtty open SABM frame when config requester
+    - tty: n_gsm: fix user open not possible at responder until initiator open
+    - tty: n_gsm: fix tty registration before control channel open
+    - tty: n_gsm: fix wrong queuing behavior in gsm_dlci_data_output()
+    - tty: n_gsm: fix missing timer to handle stalled links
+    - tty: n_gsm: fix non flow control frames during mux flow off
+    - tty: n_gsm: fix packet re-transmission without open control channel
+    - tty: n_gsm: fix race condition in gsmld_write()
+    - tty: n_gsm: fix resource allocation order in gsm_activate_mux()
+    - ASoC: qcom: Fix missing of_node_put() in
+      asoc_qcom_lpass_cpu_platform_probe()
+    - ASoC: imx-card: Fix DSD/PDM mclk frequency
+    - remoteproc: qcom: wcnss: Fix handling of IRQs
+    - vfio/ccw: Do not change FSM state in subchannel event
+    - serial: 8250_fsl: Don't report FE, PE and OE twice
+    - tty: n_gsm: fix wrong T1 retry count handling
+    - tty: n_gsm: fix DM command
+    - tty: n_gsm: fix missing corner cases in gsmld_poll()
+    - MIPS: vdso: Utilize __pa() for gic_pfn
+    - swiotlb: fail map correctly with failed io_tlb_default_mem
+    - ASoC: mt6359: Fix refcount leak bug
+    - serial: 8250_bcm7271: Save/restore RTS in suspend/resume
+    - iommu/exynos: Handle failed IOMMU device registration properly
+    - 9p: fix a bunch of checkpatch warnings
+    - 9p: Drop kref usage
+    - 9p: Add client parameter to p9_req_put()
+    - net: 9p: fix refcount leak in p9_read_work() error handling
+    - MIPS: Fixed __debug_virt_addr_valid()
+    - rpmsg: qcom_smd: Fix refcount leak in qcom_smd_parse_edge
+    - kfifo: fix kfifo_to_user() return type
+    - lib/smp_processor_id: fix imbalanced instrumentation_end() call
+    - proc: fix a dentry lock race between release_task and lookup
+    - remoteproc: qcom: pas: Check if coredump is enabled
+    - remoteproc: sysmon: Wait for SSCTL service to come up
+    - mfd: t7l66xb: Drop platform disable callback
+    - mfd: max77620: Fix refcount leak in max77620_initialise_fps
+    - iommu/arm-smmu: qcom_iommu: Add of_node_put() when breaking out of loop
+    - perf tools: Fix dso_id inode generation comparison
+    - s390/dump: fix old lowcore virtual vs physical address confusion
+    - s390/maccess: fix semantics of memcpy_real() and its callers
+    - s390/crash: fix incorrect number of bytes to copy to user space
+    - s390/zcore: fix race when reading from hardware system area
+    - ASoC: fsl_asrc: force cast the asrc_format type
+    - ASoC: fsl-asoc-card: force cast the asrc_format type
+    - ASoC: fsl_easrc: use snd_pcm_format_t type for sample_format
+    - ASoC: imx-card: use snd_pcm_format_t type for asrc_format
+    - ASoC: qcom: q6dsp: Fix an off-by-one in q6adm_alloc_copp()
+    - fuse: Remove the control interface for virtio-fs
+    - ASoC: audio-graph-card: Add of_node_put() in fail path
+    - watchdog: sp5100_tco: Fix a memory leak of EFCH MMIO resource
+    - watchdog: armada_37xx_wdt: check the return value of devm_ioremap() in
+      armada_37xx_wdt_probe()
+    - video: fbdev: amba-clcd: Fix refcount leak bugs
+    - video: fbdev: sis: fix typos in SiS_GetModeID()
+    - ASoC: mchp-spdifrx: disable end of block interrupt on failures
+    - powerpc/32: Call mmu_mark_initmem_nx() regardless of data block mapping.
+    - powerpc/32: Do not allow selection of e5500 or e6500 CPUs on PPC32
+    - powerpc/iommu: Fix iommu_table_in_use for a small default DMA window case
+    - powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and
+      alias
+    - tty: serial: fsl_lpuart: correct the count of break characters
+    - s390/dump: fix os_info virtual vs physical address confusion
+    - s390/smp: cleanup target CPU callback starting
+    - s390/smp: cleanup control register update routines
+    - s390/maccess: rework absolute lowcore accessors
+    - s390/smp: enforce lowcore protection on CPU restart
+    - f2fs: fix to remove F2FS_COMPR_FL and tag F2FS_NOCOMP_FL at the same time
+    - powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
+    - powerpc/xive: Fix refcount leak in xive_get_max_prio
+    - powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
+    - perf symbol: Fail to read phdr workaround
+    - kprobes: Forbid probing on trampoline and BPF code areas
+    - x86/bus_lock: Don't assume the init value of DEBUGCTLMSR.BUS_LOCK_DETECT to
+      be zero
+    - powerpc/pci: Fix PHB numbering when using opal-phbid
+    - genelf: Use HAVE_LIBCRYPTO_SUPPORT, not the never defined HAVE_LIBCRYPTO
+    - scripts/faddr2line: Fix vmlinux detection on arm64
+    - sched/deadline: Merge dl_task_can_attach() and dl_cpu_busy()
+    - sched, cpuset: Fix dl_cpu_busy() panic due to empty cs->cpus_allowed
+    - x86/numa: Use cpumask_available instead of hardcoded NULL check
+    - video: fbdev: arkfb: Fix a divide-by-zero bug in ark_set_pixclock()
+    - tools/thermal: Fix possible path truncations
+    - sched: Fix the check of nr_running at queue wakelist
+    - sched: Remove the limitation of WF_ON_CPU on wakelist if wakee cpu is idle
+    - sched/core: Do not requeue task on CPU excluded from cpus_mask
+    - f2fs: allow compression for mmap files in compress_mode=user
+    - f2fs: do not allow to decompress files have FI_COMPRESS_RELEASED
+    - video: fbdev: vt8623fb: Check the size of screen before memset_io()
+    - video: fbdev: arkfb: Check the size of screen before memset_io()
+    - video: fbdev: s3fb: Check the size of screen before memset_io()
+    - scsi: ufs: core: Correct ufshcd_shutdown() flow
+    - scsi: zfcp: Fix missing auto port scan and thus missing target ports
+    - scsi: qla2xxx: Fix imbalance vha->vref_count
+    - scsi: qla2xxx: Fix discovery issues in FC-AL topology
+    - scsi: qla2xxx: Turn off multi-queue for 8G adapters
+    - scsi: qla2xxx: Fix crash due to stale SRB access around I/O timeouts
+    - scsi: qla2xxx: Fix excessive I/O error messages by default
+    - scsi: qla2xxx: Fix erroneous mailbox timeout after PCI error injection
+    - scsi: qla2xxx: Wind down adapter after PCIe error
+    - scsi: qla2xxx: Fix losing FCP-2 targets on long port disable with I/Os
+    - scsi: qla2xxx: Fix losing target when it reappears during delete
+    - scsi: qla2xxx: Fix losing FCP-2 targets during port perturbation tests
+    - x86/bugs: Enable STIBP for IBPB mitigated RETBleed
+    - ftrace/x86: Add back ftrace_expected assignment
+    - x86/kprobes: Update kcb status flag after singlestepping
+    - x86/olpc: fix 'logical not is only applied to the left hand side'
+    - SMB3: fix lease break timeout when multiple deferred close handles for the
+      same file.
+    - Input: gscps2 - check return value of ioremap() in gscps2_probe()
+    - __follow_mount_rcu(): verify that mount_lock remains unchanged
+    - spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
+    - drm/mediatek: Allow commands to be sent during video mode
+    - drm/mediatek: Keep dsi as LP00 before dcs cmds transfer
+    - crypto: blake2s - remove shash module
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component
+    - usbnet: smsc95xx: Don't clear read-only PHY interrupt
+    - usbnet: smsc95xx: Avoid link settings race on interrupt reception
+    - firmware: arm_scpi: Ensure scpi_info is not assigned if the probe fails
+    - scsi: lpfc: SLI path split: Refactor lpfc_iocbq
+    - scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
+    - scsi: lpfc: SLI path split: Refactor SCSI paths
+    - scsi: lpfc: Remove extra atomic_inc on cmd_pending in queuecommand after
+      VMID
+    - intel_th: pci: Add Meteor Lake-P support
+    - intel_th: pci: Add Raptor Lake-S PCH support
+    - intel_th: pci: Add Raptor Lake-S CPU support
+    - KVM: set_msr_mce: Permit guests to ignore single-bit ECC errors
+    - KVM: x86: Signal #GP, not -EPERM, on bad WRMSR(MCi_CTL/STATUS)
+    - iommu/vt-d: avoid invalid memory access via node_online(NUMA_NO_NODE)
+    - PCI/AER: Iterate over error counters instead of error strings
+    - PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
+    - serial: 8250_pci: Refactor the loop in pci_ite887x_init()
+    - serial: 8250_pci: Replace dev_*() by pci_*() macros
+    - serial: 8250: Fold EndRun device support into OxSemi Tornado code
+    - serial: 8250: Add proper clock handling for OxSemi PCIe devices
+    - tty: 8250: Add support for Brainboxes PX cards.
+    - dm writecache: set a default MAX_WRITEBACK_JOBS
+    - kexec, KEYS, s390: Make use of built-in and secondary keyring for signature
+      verification
+    - dm thin: fix use-after-free crash in dm_sm_register_threshold_callback
+    - net/9p: Initialize the iounit field during fid creation
+    - ARM: remove some dead code
+    - timekeeping: contribute wall clock to rng on time change
+    - locking/csd_lock: Change csdlock_debug from early_param to __setup
+    - block: remove the struct blk_queue_ctx forward declaration
+    - block: don't allow the same type rq_qos add more than once
+    - btrfs: ensure pages are unlocked on cow_file_range() failure
+    - btrfs: reset block group chunk force if we have to wait
+    - btrfs: properly flag filesystem with BTRFS_FEATURE_INCOMPAT_BIG_METADATA
+    - ACPI: CPPC: Do not prevent CPPC from working in the future
+    - powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
+    - KVM: x86/pmu: Introduce the ctrl_mask value for fixed counter
+    - KVM: VMX: Mark all PERF_GLOBAL_(OVF)_CTRL bits reserved if there's no vPMU
+    - KVM: x86/pmu: Ignore pmu->global_ctrl check if vPMU doesn't support
+      global_ctrl
+    - KVM: VMX: Add helper to check if the guest PMU has PERF_GLOBAL_CTRL
+    - KVM: nVMX: Attempt to load PERF_GLOBAL_CTRL on nVMX xfer iff it exists
+    - dm raid: fix address sanitizer warning in raid_status
+    - dm raid: fix address sanitizer warning in raid_resume
+    - tracing: Add '__rel_loc' using trace event macros
+    - tracing: Avoid -Warray-bounds warning for __rel_loc macro
+    - ext4: update s_overhead_clusters in the superblock during an on-line resize
+    - ext4: fix extent status tree race in writeback error recovery path
+    - ext4: add EXT4_INODE_HAS_XATTR_SPACE macro in xattr.h
+    - ext4: fix use-after-free in ext4_xattr_set_entry
+    - ext4: correct max_inline_xattr_value_size computing
+    - ext4: correct the misjudgment in ext4_iget_extra_inode
+    - ext4: fix warning in ext4_iomap_begin as race between bmap and write
+    - ext4: check if directory block is within i_size
+    - ext4: make sure ext4_append() always allocates new block
+    - ext4: remove EA inode entry from mbcache on inode eviction
+    - ext4: use kmemdup() to replace kmalloc + memcpy
+    - ext4: unindent codeblock in ext4_xattr_block_set()
+    - ext4: fix race when reusing xattr blocks
+    - KEYS: asymmetric: enforce SM2 signature use pkey algo
+    - tpm: eventlog: Fix section mismatch for DEBUG_SECTION_MISMATCH
+    - xen-blkback: fix persistent grants negotiation
+    - xen-blkback: Apply 'feature_persistent' parameter when connect
+    - xen-blkfront: Apply 'feature_persistent' parameter when connect
+    - powerpc: Fix eh field when calling lwarx on PPC32
+    - tracing: Use a struct alignof to determine trace event field alignment
+    - mac80211: fix a memory leak where sta_info is not freed
+    - tcp: fix over estimation in sk_forced_mem_schedule()
+    - crypto: lib/blake2s - reduce stack frame usage in self test
+    - Revert "mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv"
+    - Revert "s390/smp: enforce lowcore protection on CPU restart"
+    - drm/bridge: tc358767: Fix (e)DP bridge endpoint parsing in dedicated
+      function
+    - net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
+    - drm/vc4: change vc4_dma_range_matches from a global to static
+    - tracing/perf: Avoid -Warray-bounds warning for __rel_loc macro
+    - drm/msm: Fix dirtyfb refcounting
+    - drm/meson: Fix refcount leak in meson_encoder_hdmi_init
+    - io_uring: mem-account pbuf buckets
+    - Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm regression
+    - drm/bridge: Move devm_drm_of_get_bridge to bridge/panel.c
+    - scsi: lpfc: Fix locking for lpfc_sli_iocbq_lookup()
+    - scsi: lpfc: Fix element offset in __lpfc_sli_release_iocbq_s4()
+    - scsi: lpfc: Resolve some cleanup issues following SLI path refactoring
+    - Linux 5.15.61
+
+  * CVE-2022-3028
+    - af_key: Do not call xfrm_probe_algs in parallel
+
+  * CVE-2022-2978
+    - fs: fix UAF/GPF bug in nilfs_mdt_destroy
+
+  * CVE-2022-40768
+    - scsi: stex: Properly zero out the passthrough command structure
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Mon, 17 Oct 2022 20:36:48 +0200
+
+linux (5.15.0-52.58) jammy; urgency=medium
+
+  * CVE-2022-2602
+    - SAUCE: io_uring/af_unix: defer registered files gc to io_uring release
+    - SAUCE: io_uring/af_unix: fix memleak during unix GC
+
+  * CVE-2022-41674
+    - mac80211: move CRC into struct ieee802_11_elems
+    - mac80211: mlme: find auth challenge directly
+    - mac80211: mesh: clean up rx_bcn_presp API
+    - mac80211: always allocate struct ieee802_11_elems
+    - mac80211: fix memory leaks with element parsing
+    - SAUCE: wifi: cfg80211: fix u8 overflow in
+      cfg80211_update_notlisted_nontrans()
+    - SAUCE: wifi: cfg80211/mac80211: reject bad MBSSID elements
+    - SAUCE: wifi: cfg80211: ensure length byte is present before access
+    - SAUCE: wifi: mac80211_hwsim: avoid mac80211 warning on bad rate
+    - SAUCE: wifi: cfg80211: update hidden BSSes to avoid WARN_ON
+
+  * CVE-2022-42722
+    - SAUCE: wifi: mac80211: fix crash in beacon protection for P2P-device
+
+  * CVE-2022-42721
+    - SAUCE: wifi: cfg80211: avoid nontransmitted BSS list corruption
+
+  * CVE-2022-42720
+    - SAUCE: wifi: cfg80211: fix BSS refcounting bugs
+
+  * CVE-2022-42719
+    - SAUCE: wifi: mac80211: fix MBSSID parsing use-after-free
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Thu, 13 Oct 2022 09:40:20 +0200
+
+linux (5.15.0-50.56) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-50.56 -proposed tracker (LP: #1990148)
+
+  * CVE-2022-3176
+    - io_uring: refactor poll update
+    - io_uring: move common poll bits
+    - io_uring: kill poll linking optimisation
+    - io_uring: inline io_poll_complete
+    - io_uring: correct fill events helpers types
+    - io_uring: clean cqe filling functions
+    - io_uring: poll rework
+    - io_uring: remove poll entry from list when canceling all
+    - io_uring: bump poll refs to full 31-bits
+    - io_uring: fail links when poll fails
+    - io_uring: fix wrong arm_poll error handling
+    - io_uring: fix UAF due to missing POLLFREE handling
+
+  * ip/nexthop: fix default address selection for connected nexthop
+    (LP: #1988809)
+    - selftests/net: test nexthop without gw
+
+  * ip/nexthop: fix default address selection for connected nexthop
+    (LP: #1988809) // icmp_redirect.sh in ubuntu_kernel_selftests failed on
+    Jammy 5.15.0-49.55 (LP: #1990124)
+    - ip: fix triggering of 'icmp redirect'
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 20 Sep 2022 11:17:11 +0200
+
+linux (5.15.0-49.55) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-49.55 -proposed tracker (LP: #1989785)
+
+  * amdgpu module crash after 5.15 kernel update (LP: #1981883)
+    - drm/amdgpu: fix check in fbdev init
+
+  * scsi: hisi_sas: Increase debugfs_dump_index after dump is  completed
+    (LP: #1982070)
+    - scsi: hisi_sas: Increase debugfs_dump_index after dump is completed
+
+  * [UBUNTU 22.04] s390/qeth: cache link_info for ethtool (LP: #1984103)
+    - s390/qeth: cache link_info for ethtool
+
+  * WARN in trace_event_dyn_put_ref (LP: #1987232)
+    - tracing/perf: Fix double put of trace event when init fails
+
+  * Jammy update: v5.15.60 upstream stable release (LP: #1989221)
+    - x86/speculation: Make all RETbleed mitigations 64-bit only
+    - selftests/bpf: Extend verifier and bpf_sock tests for dst_port loads
+    - selftests/bpf: Check dst_port only on the client socket
+    - block: fix default IO priority handling again
+    - tools/vm/slabinfo: Handle files in debugfs
+    - ACPI: video: Force backlight native for some TongFang devices
+    - ACPI: video: Shortening quirk list by identifying Clevo by board_name only
+    - ACPI: APEI: Better fix to avoid spamming the console with old error logs
+    - crypto: arm64/poly1305 - fix a read out-of-bound
+    - KVM: x86: do not report a vCPU as preempted outside instruction boundaries
+    - KVM: x86: do not set st->preempted when going back to user space
+    - KVM: selftests: Make hyperv_clock selftest more stable
+    - tools/kvm_stat: fix display of error when multiple processes are found
+    - selftests: KVM: Handle compiler optimizations in ucall
+    - KVM: x86/svm: add __GFP_ACCOUNT to __sev_dbg_{en,de}crypt_user()
+    - arm64: set UXN on swapper page tables
+    - btrfs: zoned: prevent allocation from previous data relocation BG
+    - btrfs: zoned: fix critical section of relocation inode writeback
+    - Bluetooth: hci_bcm: Add BCM4349B1 variant
+    - Bluetooth: hci_bcm: Add DT compatible for CYW55572
+    - dt-bindings: bluetooth: broadcom: Add BCM4349B1 DT binding
+    - Bluetooth: btusb: Add support of IMC Networks PID 0x3568
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04CA:0x4007
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04C5:0x1675
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0CB8:0xC558
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3587
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3586
+    - macintosh/adb: fix oob read in do_adb_query() function
+    - x86/speculation: Add RSB VM Exit protections
+    - x86/speculation: Add LFENCE to RSB fill sequence
+    - Linux 5.15.60
+
+  * Jammy update: v5.15.59 upstream stable release (LP: #1989218)
+    - Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
+    - Revert "ocfs2: mount shared volume without ha stack"
+    - ntfs: fix use-after-free in ntfs_ucsncmp()
+    - fs: sendfile handles O_NONBLOCK of out_fd
+    - secretmem: fix unhandled fault in truncate
+    - mm: fix page leak with multiple threads mapping the same page
+    - hugetlb: fix memoryleak in hugetlb_mcopy_atomic_pte
+    - asm-generic: remove a broken and needless ifdef conditional
+    - s390/archrandom: prevent CPACF trng invocations in interrupt context
+    - nouveau/svm: Fix to migrate all requested pages
+    - drm/simpledrm: Fix return type of simpledrm_simple_display_pipe_mode_valid()
+    - watch_queue: Fix missing rcu annotation
+    - watch_queue: Fix missing locking in add_watch_to_object()
+    - tcp: Fix data-races around sysctl_tcp_dsack.
+    - tcp: Fix a data-race around sysctl_tcp_app_win.
+    - tcp: Fix a data-race around sysctl_tcp_adv_win_scale.
+    - tcp: Fix a data-race around sysctl_tcp_frto.
+    - tcp: Fix a data-race around sysctl_tcp_nometrics_save.
+    - tcp: Fix data-races around sysctl_tcp_no_ssthresh_metrics_save.
+    - ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
+    - ice: do not setup vlan for loopback VSI
+    - scsi: ufs: host: Hold reference returned by of_parse_phandle()
+    - Revert "tcp: change pingpong threshold to 3"
+    - octeontx2-pf: Fix UDP/TCP src and dst port tc filters
+    - tcp: Fix data-races around sysctl_tcp_moderate_rcvbuf.
+    - tcp: Fix a data-race around sysctl_tcp_limit_output_bytes.
+    - tcp: Fix a data-race around sysctl_tcp_challenge_ack_limit.
+    - scsi: core: Fix warning in scsi_alloc_sgtables()
+    - scsi: mpt3sas: Stop fw fault watchdog work item during system shutdown
+    - net: ping6: Fix memleak in ipv6_renew_options().
+    - ipv6/addrconf: fix a null-ptr-deref bug for ip6_ptr
+    - net/tls: Remove the context from the list in tls_device_down
+    - igmp: Fix data-races around sysctl_igmp_qrv.
+    - net: pcs: xpcs: propagate xpcs_read error to xpcs_get_state_c37_sgmii
+    - net: sungem_phy: Add of_node_put() for reference returned by of_get_parent()
+    - tcp: Fix a data-race around sysctl_tcp_min_tso_segs.
+    - tcp: Fix a data-race around sysctl_tcp_min_rtt_wlen.
+    - tcp: Fix a data-race around sysctl_tcp_autocorking.
+    - tcp: Fix a data-race around sysctl_tcp_invalid_ratelimit.
+    - Documentation: fix sctp_wmem in ip-sysctl.rst
+    - macsec: fix NULL deref in macsec_add_rxsa
+    - macsec: fix error message in macsec_add_rxsa and _txsa
+    - macsec: limit replay window size with XPN
+    - macsec: always read MACSEC_SA_ATTR_PN as a u64
+    - net: macsec: fix potential resource leak in macsec_add_rxsa() and
+      macsec_add_txsa()
+    - net: mld: fix reference count leak in mld_{query | report}_work()
+    - tcp: Fix data-races around sk_pacing_rate.
+    - net: Fix data-races around sysctl_[rw]mem(_offset)?.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_delay_ns.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_slack_ns.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_nr.
+    - tcp: Fix data-races around sysctl_tcp_reflect_tos.
+    - ipv4: Fix data-races around sysctl_fib_notify_on_flag_change.
+    - i40e: Fix interface init with MSI interrupts (no MSI-X)
+    - sctp: fix sleep in atomic context bug in timer handlers
+    - octeontx2-pf: cn10k: Fix egress ratelimit configuration
+    - virtio-net: fix the race between refill work and close
+    - perf symbol: Correct address for bss symbols
+    - sfc: disable softirqs for ptp TX
+    - sctp: leave the err path free in sctp_stream_init to sctp_stream_free
+    - ARM: crypto: comment out gcc warning that breaks clang builds
+    - mm/hmm: fault non-owner device private entries
+    - page_alloc: fix invalid watermark check on a negative value
+    - ARM: 9216/1: Fix MAX_DMA_ADDRESS overflow
+    - EDAC/ghes: Set the DIMM label unconditionally
+    - docs/kernel-parameters: Update descriptions for "mitigations=" param with
+      retbleed
+    - locking/rwsem: Allow slowpath writer to ignore handoff bit if not set by
+      first waiter
+    - x86/bugs: Do not enable IBPB at firmware entry when IBPB is not available
+    - Linux 5.15.59
+
+  * Jammy update: v5.15.58 upstream stable release (LP: #1988479)
+    - pinctrl: stm32: fix optional IRQ support to gpios
+    - riscv: add as-options for modules with assembly compontents
+    - mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
+    - lockdown: Fix kexec lockdown bypass with ima policy
+    - drm/ttm: fix locking in vmap/vunmap TTM GEM helpers
+    - bus: mhi: host: pci_generic: add Telit FN980 v1 hardware revision
+    - bus: mhi: host: pci_generic: add Telit FN990
+    - Revert "selftest/vm: verify remap destination address in mremap_test"
+    - Revert "selftest/vm: verify mmap addr in mremap_test"
+    - PCI: hv: Fix multi-MSI to allow more than one MSI vector
+    - PCI: hv: Fix hv_arch_irq_unmask() for multi-MSI
+    - PCI: hv: Reuse existing IRTE allocation in compose_msi_msg()
+    - PCI: hv: Fix interrupt mapping for multi-MSI
+    - serial: mvebu-uart: correctly report configured baudrate value
+    - batman-adv: Use netif_rx_any_context() any.
+    - xfs: fix maxlevels comparisons in the btree staging code
+    - xfs: fold perag loop iteration logic into helper function
+    - xfs: rename the next_agno perag iteration variable
+    - xfs: terminate perag iteration reliably on agcount
+    - xfs: fix perag reference leak on iteration race with growfs
+    - xfs: prevent a WARN_ONCE() in xfs_ioc_attr_list()
+    - r8152: fix a WOL issue
+    - ip: Fix data-races around sysctl_ip_default_ttl.
+    - xfrm: xfrm_policy: fix a possible double xfrm_pols_put() in
+      xfrm_bundle_lookup()
+    - power/reset: arm-versatile: Fix refcount leak in versatile_reboot_probe
+    - RDMA/irdma: Do not advertise 1GB page size for x722
+    - RDMA/irdma: Fix sleep from invalid context BUG
+    - pinctrl: ralink: rename MT7628(an) functions to MT76X8
+    - pinctrl: ralink: rename pinctrl-rt2880 to pinctrl-ralink
+    - pinctrl: ralink: Check for null return of devm_kcalloc
+    - perf/core: Fix data race between perf_event_set_output() and
+      perf_mmap_close()
+    - ipv4/tcp: do not use per netns ctl sockets
+    - net: tun: split run_ebpf_filter() and pskb_trim() into different "if
+      statement"
+    - mm/pagealloc: sysctl: change watermark_scale_factor max limit to 30%
+    - sysctl: move some boundary constants from sysctl.c to sysctl_vals
+    - tcp: Fix data-races around sysctl_tcp_ecn.
+    - drm/amd/display: Add option to defer works of hpd_rx_irq
+    - drm/amd/display: Fork thread to offload work of hpd_rx_irq
+    - drm/amdgpu/display: add quirk handling for stutter mode
+    - drm/amd/display: Ignore First MST Sideband Message Return Error
+    - scsi: megaraid: Clear READ queue map's nr_queues
+    - scsi: ufs: core: Drop loglevel of WriteBoost message
+    - nvme: check for duplicate identifiers earlier
+    - nvme: fix block device naming collision
+    - igc: Reinstate IGC_REMOVED logic and implement it properly
+    - ip: Fix data-races around sysctl_ip_no_pmtu_disc.
+    - ip: Fix data-races around sysctl_ip_fwd_use_pmtu.
+    - ip: Fix data-races around sysctl_ip_fwd_update_priority.
+    - ip: Fix data-races around sysctl_ip_nonlocal_bind.
+    - ip: Fix a data-race around sysctl_ip_autobind_reuse.
+    - ip: Fix a data-race around sysctl_fwmark_reflect.
+    - tcp/dccp: Fix a data-race around sysctl_tcp_fwmark_accept.
+    - tcp: sk->sk_bound_dev_if once in inet_request_bound_dev_if()
+    - tcp: Fix data-races around sysctl_tcp_l3mdev_accept.
+    - tcp: Fix data-races around sysctl_tcp_mtu_probing.
+    - tcp: Fix data-races around sysctl_tcp_base_mss.
+    - tcp: Fix data-races around sysctl_tcp_min_snd_mss.
+    - tcp: Fix a data-race around sysctl_tcp_mtu_probe_floor.
+    - tcp: Fix a data-race around sysctl_tcp_probe_threshold.
+    - tcp: Fix a data-race around sysctl_tcp_probe_interval.
+    - net: stmmac: fix pm runtime issue in stmmac_dvr_remove()
+    - net: stmmac: fix unbalanced ptp clock issue in suspend/resume flow
+    - mtd: rawnand: gpmi: validate controller clock rate
+    - mtd: rawnand: gpmi: Set WAIT_FOR_READY timeout based on program/erase times
+    - net: dsa: microchip: ksz_common: Fix refcount leak bug
+    - net: skb: introduce kfree_skb_reason()
+    - net: skb: use kfree_skb_reason() in tcp_v4_rcv()
+    - net: skb: use kfree_skb_reason() in __udp4_lib_rcv()
+    - net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
+    - net: skb_drop_reason: add document for drop reasons
+    - net: netfilter: use kfree_drop_reason() for NF_DROP
+    - net: ipv4: use kfree_skb_reason() in ip_rcv_core()
+    - net: ipv4: use kfree_skb_reason() in ip_rcv_finish_core()
+    - i2c: mlxcpld: Fix register setting for 400KHz frequency
+    - i2c: cadence: Change large transfer count reset logic to be unconditional
+    - perf tests: Fix Convert perf time to TSC test for hybrid
+    - net: stmmac: fix dma queue left shift overflow issue
+    - net/tls: Fix race in TLS device down flow
+    - igmp: Fix data-races around sysctl_igmp_llm_reports.
+    - igmp: Fix a data-race around sysctl_igmp_max_memberships.
+    - igmp: Fix data-races around sysctl_igmp_max_msf.
+    - tcp: Fix data-races around keepalive sysctl knobs.
+    - tcp: Fix data-races around sysctl_tcp_syn(ack)?_retries.
+    - tcp: Fix data-races around sysctl_tcp_syncookies.
+    - tcp: Fix data-races around sysctl_tcp_migrate_req.
+    - tcp: Fix data-races around sysctl_tcp_reordering.
+    - tcp: Fix data-races around some timeout sysctl knobs.
+    - tcp: Fix a data-race around sysctl_tcp_notsent_lowat.
+    - tcp: Fix a data-race around sysctl_tcp_tw_reuse.
+    - tcp: Fix data-races around sysctl_max_syn_backlog.
+    - tcp: Fix data-races around sysctl_tcp_fastopen.
+    - tcp: Fix data-races around sysctl_tcp_fastopen_blackhole_timeout.
+    - iavf: Fix handling of dummy receive descriptors
+    - pinctrl: armada-37xx: Use temporary variable for struct device
+    - pinctrl: armada-37xx: Make use of the devm_platform_ioremap_resource()
+    - pinctrl: armada-37xx: Convert to use dev_err_probe()
+    - pinctrl: armada-37xx: use raw spinlocks for regmap to avoid invalid wait
+      context
+    - i40e: Fix erroneous adapter reinitialization during recovery process
+    - ixgbe: Add locking to prevent panic when setting sriov_numvfs to zero
+    - net: stmmac: remove redunctant disable xPCS EEE call
+    - gpio: pca953x: only use single read/write for No AI mode
+    - gpio: pca953x: use the correct range when do regmap sync
+    - gpio: pca953x: use the correct register address when regcache sync during
+      init
+    - be2net: Fix buffer overflow in be_get_module_eeprom
+    - net: dsa: sja1105: silent spi_device_id warnings
+    - net: dsa: vitesse-vsc73xx: silent spi_device_id warnings
+    - drm/imx/dcss: Add missing of_node_put() in fail path
+    - ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh.
+    - ipv4: Fix data-races around sysctl_fib_multipath_hash_policy.
+    - ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
+    - ip: Fix data-races around sysctl_ip_prot_sock.
+    - udp: Fix a data-race around sysctl_udp_l3mdev_accept.
+    - tcp: Fix data-races around sysctl knobs related to SYN option.
+    - tcp: Fix a data-race around sysctl_tcp_early_retrans.
+    - tcp: Fix data-races around sysctl_tcp_recovery.
+    - tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
+    - tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
+    - tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
+    - tcp: Fix a data-race around sysctl_tcp_stdurg.
+    - tcp: Fix a data-race around sysctl_tcp_rfc1337.
+    - tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
+    - tcp: Fix data-races around sysctl_tcp_max_reordering.
+    - gpio: gpio-xilinx: Fix integer overflow
+    - KVM: selftests: Fix target thread to be migrated in rseq_test
+    - spi: bcm2835: bcm2835_spi_handle_err(): fix NULL pointer deref for non DMA
+      transfers
+    - KVM: Don't null dereference ops->destroy
+    - mm/mempolicy: fix uninit-value in mpol_rebind_policy()
+    - bpf: Make sure mac_header was set before using it
+    - sched/deadline: Fix BUG_ON condition for deboosted tasks
+    - x86/bugs: Warn when "ibrs" mitigation is selected on Enhanced IBRS parts
+    - dlm: fix pending remove if msg allocation fails
+    - x86/uaccess: Implement macros for CMPXCHG on user addresses
+    - bitfield.h: Fix "type of reg too small for mask" test
+    - x86/entry_32: Remove .fixup usage
+    - x86/extable: Extend extable functionality
+    - x86/msr: Remove .fixup usage
+    - x86/futex: Remove .fixup usage
+    - KVM: x86: Use __try_cmpxchg_user() to emulate atomic accesses
+    - xhci: dbc: refactor xhci_dbc_init()
+    - xhci: dbc: create and remove dbc structure in dbgtty driver.
+    - xhci: dbc: Rename xhci_dbc_init and xhci_dbc_exit
+    - xhci: Set HCD flag to defer primary roothub registration
+    - mt76: fix use-after-free by removing a non-RCU wcid pointer
+    - iwlwifi: fw: uefi: add missing include guards
+    - crypto: qat - set to zero DH parameters before free
+    - crypto: qat - use pre-allocated buffers in datapath
+    - crypto: qat - refactor submission logic
+    - crypto: qat - add backlog mechanism
+    - crypto: qat - fix memory leak in RSA
+    - crypto: qat - remove dma_free_coherent() for RSA
+    - crypto: qat - remove dma_free_coherent() for DH
+    - crypto: qat - add param check for RSA
+    - crypto: qat - add param check for DH
+    - crypto: qat - re-enable registration of algorithms
+    - exfat: fix referencing wrong parent directory information after renaming
+    - tracing: Have event format check not flag %p* on __get_dynamic_array()
+    - tracing: Place trace_pid_list logic into abstract functions
+    - tracing: Fix return value of trace_pid_write()
+    - um: virtio_uml: Allow probing from devicetree
+    - um: virtio_uml: Fix broken device handling in time-travel
+    - Bluetooth: Add bt_skb_sendmsg helper
+    - Bluetooth: Add bt_skb_sendmmsg helper
+    - Bluetooth: SCO: Replace use of memcpy_from_msg with bt_skb_sendmsg
+    - Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg
+    - Bluetooth: Fix passing NULL to PTR_ERR
+    - Bluetooth: SCO: Fix sco_send_frame returning skb->len
+    - Bluetooth: Fix bt_skb_sendmmsg not allocating partial chunks
+    - exfat: use updated exfat_chain directly during renaming
+    - x86/amd: Use IBPB for firmware calls
+    - x86/alternative: Report missing return thunk details
+    - watchqueue: make sure to serialize 'wqueue->defunct' properly
+    - tty: drivers/tty/, stop using tty_schedule_flip()
+    - tty: the rest, stop using tty_schedule_flip()
+    - tty: drop tty_schedule_flip()
+    - tty: extract tty_flip_buffer_commit() from tty_flip_buffer_push()
+    - tty: use new tty_insert_flip_string_and_push_buffer() in pty_write()
+    - watch-queue: remove spurious double semicolon
+    - drm/amd/display: invalid parameter check in dmub_hpd_callback
+    - x86/extable: Prefer local labels in .set directives
+    - KVM: x86: fix typo in __try_cmpxchg_user causing non-atomicness
+    - x86: drop bogus "cc" clobber from __try_cmpxchg_user_asm()
+    - drm/amdgpu: Off by one in dm_dmub_outbox1_low_irq()
+    - x86/entry_32: Fix segment exceptions
+    - Linux 5.15.58
+
+  * Jammy update: v5.15.57 upstream stable release (LP: #1988353)
+    - x86/xen: Fix initialisation in hypercall_page after rethunk
+    - tools arch x86: Sync the msr-index.h copy with the kernel sources
+    - tools headers cpufeatures: Sync with the kernel sources
+    - um: Add missing apply_returns()
+    - x86: Use -mindirect-branch-cs-prefix for RETPOLINE builds
+    - Linux 5.15.57
+
+  * Jammy update: v5.15.56 upstream stable release (LP: #1988351)
+    - ALSA: hda - Add fixup for Dell Latitidue E5430
+    - ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
+    - ALSA: hda/realtek: Fix headset mic for Acer SF313-51
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
+    - ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
+    - xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
+    - fix race between exit_itimers() and /proc/pid/timers
+    - mm: userfaultfd: fix UFFDIO_CONTINUE on fallocated shmem pages
+    - mm: split huge PUD on wp_huge_pud fallback
+    - tracing/histograms: Fix memory leak problem
+    - net: sock: tracing: Fix sock_exceed_buf_limit not to dereference stale
+      pointer
+    - ip: fix dflt addr selection for connected nexthop
+    - ARM: 9213/1: Print message about disabled Spectre workarounds only once
+    - ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
+    - wifi: mac80211: fix queue selection for mesh/OCB interfaces
+    - cgroup: Use separate src/dst nodes when preloading css_sets for migration
+    - btrfs: return -EAGAIN for NOWAIT dio reads/writes on compressed and inline
+      extents
+    - drm/panfrost: Put mapping instead of shmem obj on
+      panfrost_mmu_map_fault_addr() error
+    - drm/panfrost: Fix shrinker list corruption by madvise IOCTL
+    - fs/remap: constrain dedupe of EOF blocks
+    - nilfs2: fix incorrect masking of permission flags for symlinks
+    - sh: convert nommu io{re,un}map() to static inline functions
+    - Revert "evm: Fix memleak in init_desc"
+    - xfs: only run COW extent recovery when there are no live extents
+    - xfs: don't include bnobt blocks when reserving free block pool
+    - xfs: run callbacks before waking waiters in xlog_state_shutdown_callbacks
+    - xfs: drop async cache flushes from CIL commits.
+    - reset: Fix devm bulk optional exclusive control getter
+    - ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
+    - spi: amd: Limit max transfer and message size
+    - ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
+    - ARM: 9210/1: Mark the FDT_FIXED sections as shareable
+    - net/mlx5e: kTLS, Fix build time constant test in TX
+    - net/mlx5e: kTLS, Fix build time constant test in RX
+    - net/mlx5e: Fix enabling sriov while tc nic rules are offloaded
+    - net/mlx5e: Fix capability check for updating vnic env counters
+    - net/mlx5e: Ring the TX doorbell on DMA errors
+    - drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
+    - ima: Fix a potential integer overflow in ima_appraise_measurement
+    - ASoC: sgtl5000: Fix noise on shutdown/remove
+    - ASoC: tas2764: Add post reset delays
+    - ASoC: tas2764: Fix and extend FSYNC polarity handling
+    - ASoC: tas2764: Correct playback volume range
+    - ASoC: tas2764: Fix amp gain register offset & default
+    - ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
+    - ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
+    - net: stmmac: dwc-qos: Disable split header for Tegra194
+    - net: ethernet: ti: am65-cpsw: Fix devlink port register sequence
+    - sysctl: Fix data races in proc_dointvec().
+    - sysctl: Fix data races in proc_douintvec().
+    - sysctl: Fix data races in proc_dointvec_minmax().
+    - sysctl: Fix data races in proc_douintvec_minmax().
+    - sysctl: Fix data races in proc_doulongvec_minmax().
+    - sysctl: Fix data races in proc_dointvec_jiffies().
+    - tcp: Fix a data-race around sysctl_tcp_max_orphans.
+    - inetpeer: Fix data-races around sysctl.
+    - net: Fix data-races around sysctl_mem.
+    - cipso: Fix data-races around sysctl.
+    - icmp: Fix data-races around sysctl.
+    - ipv4: Fix a data-race around sysctl_fib_sync_mem.
+    - ARM: dts: at91: sama5d2: Fix typo in i2s1 node
+    - ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
+    - arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
+    - arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
+    - netfilter: nf_log: incorrect offset to network header
+    - netfilter: nf_tables: replace BUG_ON by element length check
+    - drm/i915/gvt: IS_ERR() vs NULL bug in intel_gvt_update_reg_whitelist()
+    - xen/gntdev: Ignore failure to unmap INVALID_GRANT_HANDLE
+    - lockd: set fl_owner when unlocking files
+    - lockd: fix nlm_close_files
+    - tracing: Fix sleeping while atomic in kdb ftdump
+    - drm/i915/selftests: fix a couple IS_ERR() vs NULL tests
+    - drm/i915/dg2: Add Wa_22011100796
+    - drm/i915/gt: Serialize GRDOM access between multiple engine resets
+    - drm/i915/gt: Serialize TLB invalidates with GT resets
+    - drm/i915/uc: correctly track uc_fw init failure
+    - drm/i915: Require the vm mutex for i915_vma_bind()
+    - bnxt_en: Fix bnxt_reinit_after_abort() code path
+    - bnxt_en: Fix bnxt_refclk_read()
+    - sysctl: Fix data-races in proc_dou8vec_minmax().
+    - sysctl: Fix data-races in proc_dointvec_ms_jiffies().
+    - icmp: Fix data-races around sysctl_icmp_echo_enable_probe.
+    - icmp: Fix a data-race around sysctl_icmp_ignore_bogus_error_responses.
+    - icmp: Fix a data-race around sysctl_icmp_errors_use_inbound_ifaddr.
+    - icmp: Fix a data-race around sysctl_icmp_ratelimit.
+    - icmp: Fix a data-race around sysctl_icmp_ratemask.
+    - raw: Fix a data-race around sysctl_raw_l3mdev_accept.
+    - tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
+    - ipv4: Fix data-races around sysctl_ip_dynaddr.
+    - nexthop: Fix data-races around nexthop_compat_mode.
+    - net: ftgmac100: Hold reference returned by of_get_child_by_name()
+    - net: stmmac: fix leaks in probe
+    - ima: force signature verification when CONFIG_KEXEC_SIG is configured
+    - ima: Fix potential memory leak in ima_init_crypto()
+    - drm/amd/display: Only use depth 36 bpp linebuffers on DCN display engines.
+    - drm/amd/pm: Prevent divide by zero
+    - sfc: fix use after free when disabling sriov
+    - ceph: switch netfs read ops to use rreq->inode instead of
+      rreq->mapping->host
+    - seg6: fix skb checksum evaluation in SRH encapsulation/insertion
+    - seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
+    - seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
+    - sfc: fix kernel panic when creating VF
+    - KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
+    - net/tls: Check for errors in tls_device_init
+    - ACPI: video: Fix acpi_video_handles_brightness_key_presses()
+    - mm: sysctl: fix missing numa_stat when !CONFIG_HUGETLB_PAGE
+    - btrfs: rename btrfs_bio to btrfs_io_context
+    - btrfs: zoned: fix a leaked bioc in read_zone_info
+    - ksmbd: use SOCK_NONBLOCK type for kernel_accept()
+    - powerpc/xive/spapr: correct bitmap allocation size
+    - vdpa/mlx5: Initialize CVQ vringh only once
+    - vduse: Tie vduse mgmtdev and its device
+    - virtio_mmio: Add missing PM calls to freeze/restore
+    - virtio_mmio: Restore guest page size on resume
+    - netfilter: br_netfilter: do not skip all hooks with 0 priority
+    - scsi: hisi_sas: Limit max hw sectors for v3 HW
+    - cpufreq: pmac32-cpufreq: Fix refcount leak bug
+    - firmware: sysfb: Make sysfb_create_simplefb() return a pdev pointer
+    - firmware: sysfb: Add sysfb_disable() helper function
+    - fbdev: Disable sysfb device registration when removing conflicting FBs
+    - net: tipc: fix possible refcount leak in tipc_sk_create()
+    - NFC: nxp-nci: don't print header length mismatch on i2c error
+    - nvme-tcp: always fail a request when sending it failed
+    - nvme: fix regression when disconnect a recovering ctrl
+    - net: sfp: fix memory leak in sfp_probe()
+    - ASoC: ops: Fix off by one in range control validation
+    - pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux()
+    - ASoC: Realtek/Maxim SoundWire codecs: disable pm_runtime on remove
+    - ASoC: rt711-sdca-sdw: fix calibrate mutex initialization
+    - ASoC: Intel: sof_sdw: handle errors on card registration
+    - ASoC: rt711: fix calibrate mutex initialization
+    - ASoC: rt7*-sdw: harden jack_detect_handler
+    - ASoC: codecs: rt700/rt711/rt711-sdca: initialize workqueues in probe
+    - ASoC: SOF: Intel: hda-loader: Clarify the cl_dsp_init() flow
+    - ASoC: wcd938x: Fix event generation for some controls
+    - ASoC: Intel: bytcr_wm5102: Fix GPIO related probe-ordering problem
+    - ASoC: wm5110: Fix DRE control
+    - ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error
+    - ASoC: dapm: Initialise kcontrol data for mux/demux controls
+    - ASoC: cs47l15: Fix event generation for low power mux control
+    - ASoC: madera: Fix event generation for OUT1 demux
+    - ASoC: madera: Fix event generation for rate controls
+    - irqchip: or1k-pic: Undefine mask_ack for level triggered hardware
+    - x86: Clear .brk area at early boot
+    - soc: ixp4xx/npe: Fix unused match warning
+    - ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
+    - Revert "can: xilinx_can: Limit CANFD brp to 2"
+    - ALSA: usb-audio: Add quirks for MacroSilicon MS2100/MS2106 devices
+    - ALSA: usb-audio: Add quirk for Fiero SC-01
+    - ALSA: usb-audio: Add quirk for Fiero SC-01 (fw v1.0.0)
+    - nvme-pci: phison e16 has bogus namespace ids
+    - signal handling: don't use BUG_ON() for debugging
+    - USB: serial: ftdi_sio: add Belimo device ids
+    - usb: typec: add missing uevent when partner support PD
+    - usb: dwc3: gadget: Fix event pending check
+    - tty: serial: samsung_tty: set dma burst_size to 1
+    - vt: fix memory overlapping when deleting chars in the buffer
+    - serial: 8250: fix return error code in serial8250_request_std_resource()
+    - serial: stm32: Clear prev values before setting RTS delays
+    - serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle
+    - serial: 8250: Fix PM usage_count for console handover
+    - x86/pat: Fix x86_has_pat_wp()
+    - drm/aperture: Run fbdev removal before internal helpers
+    - Linux 5.15.56
+
+  * Jammy update: v5.15.55 upstream stable release (LP: #1988338)
+    - Linux 5.15.55
+
+  * Jammy update: v5.15.54 upstream stable release (LP: #1987451)
+    - mm/slub: add missing TID updates on slab deactivation
+    - mm/filemap: fix UAF in find_lock_entries
+    - Revert "selftests/bpf: Add test for bpf_timer overwriting crash"
+    - ALSA: usb-audio: Workarounds for Behringer UMC 204/404 HD
+    - ALSA: hda/realtek: Add quirk for Clevo L140PU
+    - ALSA: cs46xx: Fix missing snd_card_free() call at probe error
+    - can: bcm: use call_rcu() instead of costly synchronize_rcu()
+    - can: grcan: grcan_probe(): remove extra of_node_get()
+    - can: gs_usb: gs_usb_open/close(): fix memory leak
+    - can: m_can: m_can_chip_config(): actually enable internal timestamping
+    - can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32
+      bits
+    - can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for
+      mcp2517fd
+    - can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on
+      TBC register
+    - bpf: Fix incorrect verifier simulation around jmp32's jeq/jne
+    - bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
+    - usbnet: fix memory leak in error case
+    - net: rose: fix UAF bug caused by rose_t0timer_expiry
+    - netfilter: nft_set_pipapo: release elements in clone from abort path
+    - btrfs: rename btrfs_alloc_chunk to btrfs_create_chunk
+    - btrfs: add additional parameters to btrfs_init_tree_ref/btrfs_init_data_ref
+    - btrfs: fix invalid delayed ref after subvolume creation failure
+    - btrfs: fix warning when freeing leaf after subvolume creation failure
+    - Input: cpcap-pwrbutton - handle errors from platform_get_irq()
+    - Input: goodix - change goodix_i2c_write() len parameter type to int
+    - Input: goodix - add a goodix.h header file
+    - Input: goodix - refactor reset handling
+    - Input: goodix - try not to touch the reset-pin on x86/ACPI devices
+    - dma-buf/poll: Get a file reference for outstanding fence callbacks
+    - btrfs: fix deadlock between chunk allocation and chunk btree modifications
+    - drm/i915: Disable bonding on gen12+ platforms
+    - drm/i915/gt: Register the migrate contexts with their engines
+    - drm/i915: Replace the unconditional clflush with drm_clflush_virt_range()
+    - media: ir_toy: prevent device from hanging during transmit
+    - memory: renesas-rpc-if: Avoid unaligned bus access for HyperFlash
+    - ath11k: add hw_param for wakeup_mhi
+    - qed: Improve the stack space of filter_config()
+    - platform/x86: wmi: introduce helper to convert driver to WMI driver
+    - platform/x86: wmi: Replace read_takes_no_args with a flags field
+    - platform/x86: wmi: Fix driver->notify() vs ->probe() race
+    - mt76: mt7921: get rid of mt7921_mac_set_beacon_filter
+    - mt76: mt7921: introduce mt7921_mcu_set_beacon_filter utility routine
+    - mt76: mt7921: fix a possible race enabling/disabling runtime-pm
+    - bpf: Stop caching subprog index in the bpf_pseudo_func insn
+    - bpf, arm64: Use emit_addr_mov_i64() for BPF_PSEUDO_FUNC
+    - riscv: defconfig: enable DRM_NOUVEAU
+    - RISC-V: defconfigs: Set CONFIG_FB=y, for FB console
+    - net/mlx5e: Check action fwd/drop flag exists also for nic flows
+    - net/mlx5e: Split actions_match_supported() into a sub function
+    - net/mlx5e: TC, Reject rules with drop and modify hdr action
+    - net/mlx5e: TC, Reject rules with forward and drop actions
+    - ASoC: rt5682: Avoid the unexpected IRQ event during going to suspend
+    - ASoC: rt5682: Re-detect the combo jack after resuming
+    - ASoC: rt5682: Fix deadlock on resume
+    - netfilter: nf_tables: convert pktinfo->tprot_set to flags field
+    - netfilter: nft_payload: support for inner header matching / mangling
+    - netfilter: nft_payload: don't allow th access for fragments
+    - s390/boot: allocate amode31 section in decompressor
+    - s390/setup: use physical pointers for memblock_reserve()
+    - s390/setup: preserve memory at OLDMEM_BASE and OLDMEM_SIZE
+    - ibmvnic: init init_done_rc earlier
+    - ibmvnic: clear fop when retrying probe
+    - ibmvnic: Allow queueing resets during probe
+    - virtio-blk: avoid preallocating big SGL for data
+    - io_uring: ensure that fsnotify is always called
+    - block: use bdev_get_queue() in bio.c
+    - block: only mark bio as tracked if it really is tracked
+    - block: fix rq-qos breakage from skipping rq_qos_done_bio()
+    - stddef: Introduce struct_group() helper macro
+    - media: omap3isp: Use struct_group() for memcpy() region
+    - media: davinci: vpif: fix use-after-free on driver unbind
+    - mt76: mt76_connac: fix MCU_CE_CMD_SET_ROC definition error
+    - mt76: mt7921: do not always disable fw runtime-pm
+    - cxl/port: Hold port reference until decoder release
+    - clk: renesas: r9a07g044: Update multiplier and divider values for PLL2/3
+    - KVM: x86/mmu: Use yield-safe TDP MMU root iter in MMU notifier unmapping
+    - KVM: x86/mmu: Use common TDP MMU zap helper for MMU notifier unmap hook
+    - scsi: qla2xxx: Move heartbeat handling from DPC thread to workqueue
+    - scsi: qla2xxx: Fix laggy FC remote port session recovery
+    - scsi: qla2xxx: edif: Replace list_for_each_safe with
+      list_for_each_entry_safe
+    - scsi: qla2xxx: Fix crash during module load unload test
+    - gfs2: Fix gfs2_file_buffered_write endless loop workaround
+    - vdpa/mlx5: Avoid processing works if workqueue was destroyed
+    - btrfs: handle device lookup with btrfs_dev_lookup_args
+    - btrfs: add a btrfs_get_dev_args_from_path helper
+    - btrfs: use btrfs_get_dev_args_from_path in dev removal ioctls
+    - btrfs: remove device item and update super block in the same transaction
+    - drbd: add error handling support for add_disk()
+    - drbd: Fix double free problem in drbd_create_device
+    - drbd: fix an invalid memory access caused by incorrect use of list iterator
+    - drm/amd/display: Set min dcfclk if pipe count is 0
+    - drm/amd/display: Fix by adding FPU protection for dcn30_internal_validate_bw
+    - NFSD: De-duplicate net_generic(nf->nf_net, nfsd_net_id)
+    - NFSD: COMMIT operations must not return NFS?ERR_INVAL
+    - riscv/mm: Add XIP_FIXUP for riscv_pfn_base
+    - iio: accel: mma8452: use the correct logic to get mma8452_data
+    - batman-adv: Use netif_rx().
+    - mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
+    - Compiler Attributes: add __alloc_size() for better bounds checking
+    - mm: vmalloc: introduce array allocation functions
+    - KVM: use __vcalloc for very large allocations
+    - btrfs: don't access possibly stale fs_info data in device_list_add
+    - KVM: s390x: fix SCK locking
+    - scsi: qla2xxx: Fix loss of NVMe namespaces after driver reload test
+    - powerpc/32: Don't use lmw/stmw for saving/restoring non volatile regs
+    - powerpc: flexible GPR range save/restore macros
+    - powerpc/tm: Fix more userspace r13 corruption
+    - serial: sc16is7xx: Clear RS485 bits in the shutdown
+    - bus: mhi: core: Use correctly sized arguments for bit field
+    - bus: mhi: Fix pm_state conversion to string
+    - stddef: Introduce DECLARE_FLEX_ARRAY() helper
+    - uapi/linux/stddef.h: Add include guards
+    - ASoC: rt5682: move clk related code to rt5682_i2c_probe
+    - ASoC: rt5682: fix an incorrect NULL check on list iterator
+    - drm/amd/vcn: fix an error msg on vcn 3.0
+    - KVM: Don't create VM debugfs files outside of the VM directory
+    - tty: n_gsm: Modify CR,PF bit when config requester
+    - tty: n_gsm: Save dlci address open status when config requester
+    - tty: n_gsm: fix frame reception handling
+    - ALSA: usb-audio: add mapping for MSI MPG X570S Carbon Max Wifi.
+    - ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.
+    - tty: n_gsm: fix missing update of modem controls after DLCI open
+    - btrfs: zoned: encapsulate inode locking for zoned relocation
+    - btrfs: zoned: use dedicated lock for data relocation
+    - KVM: Initialize debugfs_dentry when a VM is created to avoid NULL deref
+    - mm/hwpoison: mf_mutex for soft offline and unpoison
+    - mm/hwpoison: avoid the impact of hwpoison_filter() return value on mce
+      handler
+    - mm/memory-failure.c: fix race with changing page compound again
+    - mm/hwpoison: fix race between hugetlb free/demotion and
+      memory_failure_hugetlb()
+    - tty: n_gsm: fix invalid use of MSC in advanced option
+    - tty: n_gsm: fix sometimes uninitialized warning in gsm_dlci_modem_output()
+    - serial: 8250_mtk: Make sure to select the right FEATURE_SEL
+    - tty: n_gsm: fix invalid gsmtty_write_room() result
+    - drm/i915: Fix a race between vma / object destruction and unbinding
+    - drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb
+    - drm/mediatek: Remove the pointer of struct cmdq_client
+    - drm/mediatek: Detect CMDQ execution timeout
+    - drm/mediatek: Add cmdq_handle in mtk_crtc
+    - drm/mediatek: Add vblank register/unregister callback functions
+    - Bluetooth: protect le accept and resolv lists with hdev->lock
+    - Bluetooth: btmtksdio: fix use-after-free at btmtksdio_recv_event
+    - io_uring: avoid io-wq -EAGAIN looping for !IOPOLL
+    - irqchip/gic-v3: Ensure pseudo-NMIs have an ISB between ack and handling
+    - irqchip/gic-v3: Refactor ISB + EOIR at ack time
+    - rxrpc: Fix locking issue
+    - dt-bindings: soc: qcom: smd-rpm: Add compatible for MSM8953 SoC
+    - dt-bindings: soc: qcom: smd-rpm: Fix missing MSM8936 compatible
+    - module: change to print useful messages from elf_validity_check()
+    - module: fix [e_shstrndx].sh_size=0 OOB access
+    - iommu/vt-d: Fix PCI bus rescan device hot add
+    - fbdev: fbmem: Fix logo center image dx issue
+    - PM: runtime: Redefine pm_runtime_release_supplier()
+    - memregion: Fix memregion_free() fallback definition
+    - video: of_display_timing.h: include errno.h
+    - powerpc/powernv: delay rng platform device creation until later in boot
+    - net: dsa: qca8k: reset cpu port on MTU change
+    - can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
+    - can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
+    - can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
+    - xfs: remove incorrect ASSERT in xfs_rename
+    - Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown"
+    - btrfs: fix error pointer dereference in btrfs_ioctl_rm_dev_v2()
+    - virtio-blk: modify the value type of num in virtio_queue_rq()
+    - btrfs: fix use of uninitialized variable at rm device ioctl
+    - tty: n_gsm: fix encoding of command/response bit
+    - ARM: meson: Fix refcount leak in meson_smp_prepare_cpus
+    - pinctrl: sunxi: a83t: Fix NAND function name for some pins
+    - ASoC: rt711: Add endianness flag in snd_soc_component_driver
+    - ASoC: rt711-sdca: Add endianness flag in snd_soc_component_driver
+    - ASoC: codecs: rt700/rt711/rt711-sdca: resume bus/codec in .set_jack_detect
+    - arm64: dts: qcom: msm8994: Fix CPU6/7 reg values
+    - arm64: dts: qcom: sdm845: use dispcc AHB clock for mdss node
+    - ARM: mxs_defconfig: Enable the framebuffer
+    - arm64: dts: imx8mp-evk: correct mmc pad settings
+    - arm64: dts: imx8mp-evk: correct the uart2 pinctl value
+    - arm64: dts: imx8mp-evk: correct gpio-led pad settings
+    - arm64: dts: imx8mp-evk: correct vbus pad settings
+    - arm64: dts: imx8mp-evk: correct eqos pad settings
+    - arm64: dts: imx8mp-evk: correct I2C1 pad settings
+    - arm64: dts: imx8mp-evk: correct I2C3 pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct uart pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct eqos pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct i2c2 & mmc settings
+    - pinctrl: sunxi: sunxi_pconf_set: use correct offset
+    - arm64: dts: qcom: msm8992-*: Fix vdd_lvs1_2-supply typo
+    - ARM: at91: pm: use proper compatible for sama5d2's rtc
+    - ARM: at91: pm: use proper compatibles for sam9x60's rtc and rtt
+    - ARM: at91: pm: use proper compatibles for sama7g5's rtc and rtt
+    - ARM: dts: at91: sam9x60ek: fix eeprom compatible and size
+    - ARM: dts: at91: sama5d2_icp: fix eeprom compatibles
+    - ARM: at91: fix soc detection for SAM9X60 SiPs
+    - xsk: Clear page contiguity bit when unmapping pool
+    - i2c: piix4: Fix a memory leak in the EFCH MMIO support
+    - i40e: Fix dropped jumbo frames statistics
+    - i40e: Fix VF's MAC Address change on VM
+    - ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
+    - ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
+    - ibmvnic: Properly dispose of all skbs during a failover.
+    - selftests: forwarding: fix flood_unicast_test when h2 supports
+      IFF_UNICAST_FLT
+    - selftests: forwarding: fix learning_test when h1 supports IFF_UNICAST_FLT
+    - selftests: forwarding: fix error message in learning_test
+    - r8169: fix accessing unset transport header
+    - i2c: cadence: Unregister the clk notifier in error path
+    - dmaengine: imx-sdma: Allow imx8m for imx7 FW revs
+    - misc: rtsx_usb: fix use of dma mapped buffer for usb bulk transfer
+    - misc: rtsx_usb: use separate command and response buffers
+    - misc: rtsx_usb: set return value in rsp_buf alloc err path
+    - Revert "mm/memory-failure.c: fix race with changing page compound again"
+    - Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
+    - dt-bindings: dma: allwinner,sun50i-a64-dma: Fix min/max typo
+    - ida: don't use BUG_ON() for debugging
+    - dmaengine: pl330: Fix lockdep warning about non-static key
+    - dmaengine: lgm: Fix an error handling path in intel_ldma_probe()
+    - dmaengine: at_xdma: handle errors of at_xdmac_alloc_desc() correctly
+    - dmaengine: ti: Fix refcount leak in ti_dra7_xbar_route_allocate
+    - dmaengine: qcom: bam_dma: fix runtime PM underflow
+    - dmaengine: ti: Add missing put_device in ti_dra7_xbar_route_allocate
+    - dmaengine: idxd: force wq context cleanup on device disable path
+    - selftests/net: fix section name when using xdp_dummy.o
+    - Linux 5.15.54
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 16 Sep 2022 10:59:58 +0200
+
+linux (5.15.0-48.54) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-48.54 -proposed tracker (LP: #1987775)
+
+  * System freeze after resuming from suspend due to PCI ASPM settings
+    (LP: #1980829)
+    - SAUCE: PCI/ASPM: Save/restore L1SS Capability for suspend/resume
+    - SAUCE: whitelist platforms that needs save/restore ASPM L1SS for
+      suspend/resume
+
+  * [SRU][J/OEM-5.17][PATCH 0/1] Fix oled brightness set above frame-average
+    luminance (LP: #1978986)
+    - SAUCE: drm: New function to get luminance range based on static hdr metadata
+    - SAUCE: drm/amdgpu_dm: Rely on split out luminance calculation function
+    - SAUCE: drm/i915: Use luminance range calculated during edid parsing
+
+  * Jammy: Add OVS Internal Port HW Offload to mlx5 driver (LP: #1983498)
+    - net/mlx5e: Refactor rx handler of represetor device
+    - net/mlx5e: Use generic name for the forwarding dev pointer
+    - net/mlx5: E-Switch, Add ovs internal port mapping to metadata support
+    - net/mlx5e: Support accept action
+    - net/mlx5e: Accept action skbedit in the tc actions list
+    - net/mlx5e: Offload tc rules that redirect to ovs internal port
+    - net/mlx5e: Offload internal port as encap route device
+    - net/mlx5e: Enable TC offload for ingress MACVLAN
+    - net/mlx5e: Add indirect tc offload of ovs internal port
+    - net/mlx5e: Term table handling of internal port rules
+    - net/mlx5: Support internal port as decap route device
+    - net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'
+    - net/mlx5e: TC, Fix memory leak with rules with internal port
+    - net/mlx5e: Fix skb memory leak when TC classifier action offloads are
+      disabled
+    - net/mlx5e: Fix nullptr on deleting mirroring rule
+    - net/mlx5e: Avoid implicit modify hdr for decap drop rule
+    - net/mlx5e: Fix wrong source vport matching on tunnel rule
+    - net/mlx5e: TC, fix decap fallback to uplink when int port not supported
+
+  * Remove unused variable from i915 psr (LP: #1986798)
+    - SAUCE: drm/i915/display/psr: Remove unused variable
+
+  * refactoring of overlayfs fix to properly support shiftfs (LP: #1983640)
+    - SAUCE: overlayfs: remove CONFIG_AUFS_FS dependency
+
+  * Jammy update: v5.15.53 upstream stable release (LP: #1986728)
+    - Revert "drm/amdgpu/display: set vblank_disable_immediate for DC"
+    - drm/amdgpu: To flush tlb for MMHUB of RAVEN series
+    - ksmbd: set the range of bytes to zero without extending file size in
+      FSCTL_ZERO_DATA
+    - ksmbd: check invalid FileOffset and BeyondFinalZero in FSCTL_ZERO_DATA
+    - ksmbd: use vfs_llseek instead of dereferencing NULL
+    - ipv6: take care of disable_policy when restoring routes
+    - net: phy: Don't trigger state machine while in suspend
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG SX6000LNP (AKA SPECTRIX
+      S40G)
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA IM2P33F8ABR1
+    - nvdimm: Fix badblocks clear off-by-one error
+    - powerpc/prom_init: Fix kernel config grep
+    - powerpc/book3e: Fix PUD allocation size in map_kernel_page()
+    - powerpc/bpf: Fix use of user_pt_regs in uapi
+    - dm raid: fix accesses beyond end of raid member array
+    - dm raid: fix KASAN warning in raid5_add_disks
+    - s390/archrandom: simplify back to earlier design and initialize earlier
+    - SUNRPC: Fix READ_PLUS crasher
+    - net: rose: fix UAF bugs caused by timer handler
+    - net: usb: ax88179_178a: Fix packet receiving
+    - virtio-net: fix race between ndo_open() and virtio_device_ready()
+    - selftests/net: pass ipv6_args to udpgso_bench's IPv6 TCP test
+    - net: dsa: bcm_sf2: force pause link settings
+    - net: tun: unlink NAPI from device on destruction
+    - net: tun: stop NAPI when detaching queues
+    - net: dp83822: disable false carrier interrupt
+    - net: dp83822: disable rx error interrupt
+    - RDMA/qedr: Fix reporting QP timeout attribute
+    - RDMA/cm: Fix memory leak in ib_cm_insert_listen
+    - linux/dim: Fix divide by 0 in RDMA DIM
+    - net: usb: asix: do not force pause frames support
+    - usbnet: fix memory allocation in helpers
+    - selftests: mptcp: more stable diag tests
+    - net: ipv6: unexport __init-annotated seg6_hmac_net_init()
+    - NFSD: restore EINVAL error translation in nfsd_commit()
+    - vfs: fix copy_file_range() regression in cross-fs copies
+    - caif_virtio: fix race between virtio_device_ready() and ndo_open()
+    - PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
+    - vdpa/mlx5: Update Control VQ callback information
+    - s390: remove unneeded 'select BUILD_BIN2C'
+    - netfilter: nft_dynset: restore set element counter when failing to update
+    - net/dsa/hirschmann: Add missing of_node_get() in hellcreek_led_setup()
+    - net/sched: act_api: Notify user space if any actions were flushed before
+      error
+    - net: asix: fix "can't send until first packet is send" issue
+    - net: bonding: fix possible NULL deref in rlb code
+    - net: phy: ax88772a: fix lost pause advertisement configuration
+    - net: bonding: fix use-after-free after 802.3ad slave unbind
+    - powerpc/memhotplug: Add add_pages override for PPC
+    - nfc: nfcmrvl: Fix irq_of_parse_and_map() return value
+    - NFC: nxp-nci: Don't issue a zero length i2c_master_read()
+    - tipc: move bc link creation back to tipc_node_create
+    - epic100: fix use after free on rmmod
+    - io_uring: ensure that send/sendmsg and recv/recvmsg check sqe->ioprio
+    - ACPI: video: Change how we determine if brightness key-presses are handled
+    - tunnels: do not assume mac header is set in skb_tunnel_check_pmtu()
+    - ipv6/sit: fix ipip6_tunnel_get_prl return value
+    - ipv6: fix lockdep splat in in6_dump_addrs()
+    - mlxsw: spectrum_router: Fix rollback in tunnel next hop init
+    - net: tun: avoid disabling NAPI twice
+    - MAINTAINERS: add Leah as xfs maintainer for 5.15.y
+    - tcp: add a missing nf_reset_ct() in 3WHS handling
+    - selftests/bpf: Add test_verifier support to fixup kfunc call insns
+    - selftests/rseq: remove ARRAY_SIZE define from individual tests
+    - selftests/rseq: introduce own copy of rseq uapi header
+    - selftests/rseq: Remove useless assignment to cpu variable
+    - selftests/rseq: Remove volatile from __rseq_abi
+    - selftests/rseq: Introduce rseq_get_abi() helper
+    - selftests/rseq: Introduce thread pointer getters
+    - selftests/rseq: Uplift rseq selftests for compatibility with glibc-2.35
+    - selftests/rseq: Fix ppc32: wrong rseq_cs 32-bit field pointer on big endian
+    - selftests/rseq: Fix ppc32 missing instruction selection "u" and "x" for
+      load/store
+    - selftests/rseq: Fix ppc32 offsets by using long rather than off_t
+    - selftests/rseq: Fix warnings about #if checks of undefined tokens
+    - selftests/rseq: Remove arm/mips asm goto compiler work-around
+    - selftests/rseq: Fix: work-around asm goto compiler bugs
+    - selftests/rseq: x86-64: use %fs segment selector for accessing rseq thread
+      area
+    - selftests/rseq: x86-32: use %gs segment selector for accessing rseq thread
+      area
+    - selftests/rseq: Change type of rseq_offset to ptrdiff_t
+    - xen/blkfront: fix leaking data in shared pages
+    - xen/netfront: fix leaking data in shared pages
+    - xen/netfront: force data bouncing when backend is untrusted
+    - xen/blkfront: force data bouncing when backend is untrusted
+    - xen-netfront: restore __skb_queue_tail() positioning in
+      xennet_get_responses()
+    - xen/arm: Fix race in RB-tree based P2M accounting
+    - net: usb: qmi_wwan: add Telit 0x1070 composition
+    - clocksource/drivers/ixp4xx: remove EXPORT_SYMBOL_GPL from
+      ixp4xx_timer_setup()
+    - fsi: occ: Force sequence numbering per OCC
+    - net: fix IFF_TX_SKB_NO_LINEAR definition
+    - drm/i915/gem: add missing else
+    - drm/msm/gem: Fix error return on fence id alloc fail
+    - drivers: cpufreq: Add missing of_node_put() in qoriq-cpufreq.c
+    - platform/x86: panasonic-laptop: de-obfuscate button codes
+    - platform/x86: panasonic-laptop: sort includes alphabetically
+    - platform/x86: panasonic-laptop: revert "Resolve hotkey double trigger bug"
+    - platform/x86: panasonic-laptop: don't report duplicate brightness key-
+      presses
+    - platform/x86: panasonic-laptop: filter out duplicate volume up/down/mute
+      keypresses
+    - drm/fourcc: fix integer type usage in uapi header
+    - hwmon: (occ) Remove sequence numbering and checksum calculation
+    - hwmon: (occ) Prevent power cap command overwriting poll response
+    - hwmon: (ibmaem) don't call platform_device_del() if platform_device_add()
+      fails
+    - Linux 5.15.53
+
+  * Jammy update: v5.15.52 upstream stable release (LP: #1986724)
+    - tick/nohz: unexport __init-annotated tick_nohz_full_setup()
+    - xfs: use kmem_cache_free() for kmem_cache objects
+    - xfs: punch out data fork delalloc blocks on COW writeback failure
+    - xfs: Fix the free logic of state in xfs_attr_node_hasname
+    - xfs: remove all COW fork extents when remounting readonly
+    - xfs: check sb_meta_uuid for dabuf buffer recovery
+    - xfs: prevent UAF in xfs_log_item_in_current_chkpt
+    - xfs: only bother with sync_filesystem during readonly remount
+    - powerpc/ftrace: Remove ftrace init tramp once kernel init is complete
+    - fs: add is_idmapped_mnt() helper
+    - fs: move mapping helpers
+    - fs: tweak fsuidgid_has_mapping()
+    - fs: account for filesystem mappings
+    - docs: update mapping documentation
+    - fs: use low-level mapping helpers
+    - fs: remove unused low-level mapping helpers
+    - fs: port higher-level mapping helpers
+    - fs: add i_user_ns() helper
+    - fs: support mapped mounts of mapped filesystems
+    - fs: fix acl translation
+    - fs: account for group membership
+    - rtw88: 8821c: support RFE type4 wifi NIC
+    - rtw88: rtw8821c: enable rfe 6 devices
+    - net: mscc: ocelot: allow unregistered IP multicast flooding to CPU
+    - io_uring: fix not locked access to fixed buf table
+    - Linux 5.15.52
+
+  * Jammy update: v5.15.51 upstream stable release (LP: #1986718)
+    - random: schedule mix_interrupt_randomness() less often
+    - random: quiet urandom warning ratelimit suppression message
+    - ALSA: hda/via: Fix missing beep setup
+    - ALSA: hda/conexant: Fix missing beep setup
+    - ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop
+    - ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
+    - ALSA: hda/realtek: Add quirk for Clevo PD70PNT
+    - ALSA: hda/realtek: Add quirk for Clevo NS50PU
+    - net: openvswitch: fix parsing of nw_proto for IPv6 fragments
+    - 9p: Fix refcounting during full path walks for fid lookups
+    - 9p: fix fid refcount leak in v9fs_vfs_atomic_open_dotl
+    - 9p: fix fid refcount leak in v9fs_vfs_get_link
+    - btrfs: fix hang during unmount when block group reclaim task is running
+    - btrfs: prevent remounting to v1 space cache for subpage mount
+    - btrfs: add error messages to all unrecognized mount options
+    - scsi: ibmvfc: Store vhost pointer during subcrq allocation
+    - scsi: ibmvfc: Allocate/free queue resource only during probe/remove
+    - mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing
+    - mmc: mediatek: wait dma stop bit reset to 0
+    - xen/gntdev: Avoid blocking in unmap_grant_pages()
+    - MAINTAINERS: Add new IOMMU development mailing list
+    - ata: libata: add qc->flags in ata_qc_complete_template tracepoint
+    - dm era: commit metadata in postsuspend after worker stops
+    - dm mirror log: clear log bits up to BITS_PER_LONG boundary
+    - tracing/kprobes: Check whether get_kretprobe() returns NULL in
+      kretprobe_dispatcher()
+    - drm/i915: Implement w/a 22010492432 for adl-s
+    - USB: serial: pl2303: add support for more HXN (G) types
+    - USB: serial: option: add Telit LE910Cx 0x1250 composition
+    - USB: serial: option: add Quectel EM05-G modem
+    - USB: serial: option: add Quectel RM500K module support
+    - drm/msm: Ensure mmap offset is initialized
+    - drm/msm: Fix double pm_runtime_disable() call
+    - netfilter: use get_random_u32 instead of prandom
+    - scsi: scsi_debug: Fix zone transition to full condition
+    - drm/msm: Switch ordering of runpm put vs devfreq_idle
+    - scsi: iscsi: Exclude zero from the endpoint ID range
+    - xsk: Fix generic transmit when completion queue reservation fails
+    - drm/msm: use for_each_sgtable_sg to iterate over scatterlist
+    - bpf: Fix request_sock leak in sk lookup helpers
+    - drm/sun4i: Fix crash during suspend after component bind failure
+    - bpf, x86: Fix tail call count offset calculation on bpf2bpf call
+    - scsi: storvsc: Correct reporting of Hyper-V I/O size limits
+    - phy: aquantia: Fix AN when higher speeds than 1G are not advertised
+    - KVM: arm64: Prevent kmemleak from accessing pKVM memory
+    - net: Write lock dev_base_lock without disabling bottom halves.
+    - net: fix data-race in dev_isalive()
+    - tipc: fix use-after-free Read in tipc_named_reinit
+    - igb: fix a use-after-free issue in igb_clean_tx_ring
+    - bonding: ARP monitor spams NETDEV_NOTIFY_PEERS notifiers
+    - ethtool: Fix get module eeprom fallback
+    - net/sched: sch_netem: Fix arithmetic in netem_dump() for 32-bit platforms
+    - drm/msm/mdp4: Fix refcount leak in mdp4_modeset_init_intf
+    - drm/msm/dp: check core_initialized before disable interrupts at
+      dp_display_unbind()
+    - drm/msm/dp: Drop now unused hpd_high member
+    - drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read failed
+    - drm/msm/dp: do not initialize phy until plugin interrupt received
+    - drm/msm/dp: force link training for display resolution change
+    - perf arm-spe: Don't set data source if it's not a memory operation
+    - erspan: do not assume transport header is always set
+    - net/tls: fix tls_sk_proto_close executed repeatedly
+    - udmabuf: add back sanity check
+    - selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
+    - xen-blkfront: Handle NULL gendisk
+    - x86/xen: Remove undefined behavior in setup_features()
+    - MIPS: Remove repetitive increase irq_err_count
+    - afs: Fix dynamic root getattr
+    - ice: ethtool: advertise 1000M speeds properly
+    - regmap-irq: Fix a bug in regmap_irq_enable() for type_in_mask chips
+    - regmap-irq: Fix offset/index mismatch in read_sub_irq_data()
+    - virtio_net: fix xdp_rxq_info bug after suspend/resume
+    - Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
+    - sock: redo the psock vs ULP protection check
+    - nvme-pci: add NO APST quirk for Kioxia device
+    - nvme: move the Samsung X5 quirk entry to the core quirks
+    - gpio: winbond: Fix error code in winbond_gpio_get()
+    - s390/cpumf: Handle events cycles and instructions identical
+    - iio: mma8452: fix probe fail when device tree compatible is used.
+    - iio: magnetometer: yas530: Fix memchr_inv() misuse
+    - iio: adc: vf610: fix conversion mode sysfs node name
+    - usb: typec: wcove: Drop wrong dependency to INTEL_SOC_PMIC
+    - xhci-pci: Allow host runtime PM as default for Intel Raptor Lake xHCI
+    - xhci-pci: Allow host runtime PM as default for Intel Meteor Lake xHCI
+    - usb: gadget: Fix non-unique driver names in raw-gadget driver
+    - USB: gadget: Fix double-free bug in raw_gadget driver
+    - usb: chipidea: udc: check request status before setting device address
+    - dt-bindings: usb: ohci: Increase the number of PHYs
+    - dt-bindings: usb: ehci: Increase the number of PHYs
+    - btrfs: don't set lock_owner when locking extent buffer for reading
+    - btrfs: fix deadlock with fsync+fiemap+transaction commit
+    - f2fs: attach inline_data after setting compression
+    - iio:humidity:hts221: rearrange iio trigger get and register
+    - iio:chemical:ccs811: rearrange iio trigger get and register
+    - iio:accel:kxcjk-1013: rearrange iio trigger get and register
+    - iio:accel:bma180: rearrange iio trigger get and register
+    - iio:accel:mxc4005: rearrange iio trigger get and register
+    - iio: accel: mma8452: ignore the return value of reset operation
+    - iio: gyro: mpu3050: Fix the error handling in mpu3050_power_up()
+    - iio: trigger: sysfs: fix use-after-free on remove
+    - iio: adc: stm32: fix maximum clock rate for stm32mp15x
+    - iio: imu: inv_icm42600: Fix broken icm42600 (chip id 0 value)
+    - iio: afe: rescale: Fix boolean logic bug
+    - iio: adc: stm32: Fix ADCs iteration in irq handler
+    - iio: adc: stm32: Fix IRQs on STM32F4 by removing custom spurious IRQs
+      message
+    - iio: adc: axp288: Override TS pin bias current for some models
+    - iio: adc: rzg2l_adc: add missing fwnode_handle_put() in
+      rzg2l_adc_parse_properties()
+    - iio: adc: adi-axi-adc: Fix refcount leak in adi_axi_adc_attach_client
+    - iio: adc: ti-ads131e08: add missing fwnode_handle_put() in
+      ads131e08_alloc_channels()
+    - xtensa: xtfpga: Fix refcount leak bug in setup
+    - xtensa: Fix refcount leak bug in time.c
+    - parisc/stifb: Fix fb_is_primary_device() only available with CONFIG_FB_STI
+    - parisc: Enable ARCH_HAS_STRICT_MODULE_RWX
+    - powerpc/microwatt: wire up rng during setup_arch()
+    - powerpc: Enable execve syscall exit tracepoint
+    - powerpc/rtas: Allow ibm,platform-dump RTAS call with null buffer address
+    - powerpc/powernv: wire up rng during setup_arch
+    - drm/msm/dp: Always clear mask bits to disable interrupts at
+      dp_ctrl_reset_irq_ctrl()
+    - ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node
+    - ARM: dts: imx6qdl: correct PU regulator ramp delay
+    - arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode
+    - ARM: exynos: Fix refcount leak in exynos_map_pmu
+    - soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe
+    - ARM: Fix refcount leak in axxia_boot_secondary
+    - memory: samsung: exynos5422-dmc: Fix refcount leak in of_get_dram_timings
+    - ARM: cns3xxx: Fix refcount leak in cns3xxx_init
+    - modpost: fix section mismatch check for exported init/exit sections
+    - ARM: dts: bcm2711-rpi-400: Fix GPIO line names
+    - random: update comment from copy_to_user() -> copy_to_iter()
+    - perf build-id: Fix caching files with a wrong build ID
+    - dma-direct: use the correct size for dma_set_encrypted()
+    - kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS (2nd attempt)
+    - powerpc/pseries: wire up rng during setup_arch()
+    - Linux 5.15.51
+
+  * Jammy update: v5.15.50 upstream stable release (LP: #1986715)
+    - net: mana: Add handling of CQE_RX_TRUNCATED
+    - zonefs: fix zonefs_iomap_begin() for reads
+    - usb: gadget: u_ether: fix regression in setting fixed MAC address
+    - bpf: Fix calling global functions from BPF_PROG_TYPE_EXT programs
+    - selftests/bpf: Add selftest for calling global functions from freplace
+    - serial: core: Initialize rs485 RTS polarity already on probe
+    - arm64: mm: Don't invalidate FROM_DEVICE buffers at start of DMA transfer
+    - Linux 5.15.50
+
+  * Jammy update: v5.15.49 upstream stable release (LP: #1983149)
+    - Revert "drm/amd/display: Fix DCN3 B0 DP Alt Mapping"
+    - nfsd: Replace use of rwsem with errseq_t
+    - arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3
+    - arm64: dts: imx8mn-beacon: Enable RTS-CTS on UART3
+    - powerpc/kasan: Silence KASAN warnings in __get_wchan()
+    - ASoC: nau8822: Add operation for internal PLL off and on
+    - drm/amd/display: Read Golden Settings Table from VBIOS
+    - drm/amdkfd: Use mmget_not_zero in MMU notifier
+    - dma-debug: make things less spammy under memory pressure
+    - ASoC: cs42l52: Fix TLV scales for mixer controls
+    - ASoC: cs35l36: Update digital volume TLV
+    - ASoC: cs53l30: Correct number of volume levels on SX controls
+    - ASoC: cs42l52: Correct TLV for Bypass Volume
+    - ASoC: cs42l56: Correct typo in minimum level for SX volume controls
+    - ASoC: cs42l51: Correct minimum value for SX volume control
+    - drm/amdkfd: add pinned BOs to kfd_bo_list
+    - ata: libata-core: fix NULL pointer deref in ata_host_alloc_pinfo()
+    - quota: Prevent memory allocation recursion while holding dq_lock
+    - ASoC: wm8962: Fix suspend while playing music
+    - ASoC: es8328: Fix event generation for deemphasis control
+    - ASoC: wm_adsp: Fix event generation for wm_adsp_fw_put()
+    - Input: soc_button_array - also add Lenovo Yoga Tablet2 1051F to
+      dmi_use_low_level_irq
+    - scsi: vmw_pvscsi: Expand vcpuHint to 16 bits
+    - scsi: lpfc: Resolve NULL ptr dereference after an ELS LOGO is aborted
+    - scsi: lpfc: Fix port stuck in bypassed state after LIP in PT2PT topology
+    - scsi: lpfc: Allow reduced polling rate for nvme_admin_async_event cmd
+      completion
+    - scsi: mpt3sas: Fix out-of-bounds compiler warning
+    - scsi: ipr: Fix missing/incorrect resource cleanup in error case
+    - scsi: pmcraid: Fix missing resource cleanup in error case
+    - ALSA: hda/realtek - Add HW8326 support
+    - virtio-mmio: fix missing put_device() when vm_cmdline_parent registration
+      failed
+    - nfc: nfcmrvl: Fix memory leak in nfcmrvl_play_deferred
+    - ipv6: Fix signed integer overflow in l2tp_ip6_sendmsg
+    - net: ethernet: mtk_eth_soc: fix misuse of mem alloc interface
+      netdev[napi]_alloc_frag
+    - gcc-12: disable '-Wdangling-pointer' warning for now
+    - mellanox: mlx5: avoid uninitialized variable warning with gcc-12
+    - MIPS: Loongson-3: fix compile mips cpu_hwmon as module build error.
+    - random: credit cpu and bootloader seeds by default
+    - gpio: dwapb: Don't print error on -EPROBE_DEFER
+    - platform/x86: gigabyte-wmi: Add Z690M AORUS ELITE AX DDR4 support
+    - platform/x86: gigabyte-wmi: Add support for B450M DS3H-CF
+    - platform/x86/intel: hid: Add Surface Go to VGBS allow list
+    - staging: r8188eu: fix rtw_alloc_hwxmits error detection for now
+    - staging: r8188eu: Use zeroing allocator in wpa_set_encryption()
+    - staging: r8188eu: Fix warning of array overflow in ioctl_linux.c
+    - pNFS: Don't keep retrying if the server replied NFS4ERR_LAYOUTUNAVAILABLE
+    - pNFS: Avoid a live lock condition in pnfs_update_layout()
+    - sunrpc: set cl_max_connect when cloning an rpc_clnt
+    - clocksource: hyper-v: unexport __init-annotated hv_init_clocksource()
+    - i40e: Fix adding ADQ filter to TC0
+    - i40e: Fix calculating the number of queue pairs
+    - i40e: Fix call trace in setup_tx_descriptors
+    - Drivers: hv: vmbus: Release cpu lock in error case
+    - tty: goldfish: Fix free_irq() on remove
+    - misc: atmel-ssc: Fix IRQ check in ssc_probe
+    - io_uring: fix races with file table unregister
+    - io_uring: fix races with buffer table unregister
+    - drm/i915/reset: Fix error_state_read ptr + offset use
+    - net: hns3: split function hclge_update_port_base_vlan_cfg()
+    - net: hns3: set port base vlan tbl_sta to false before removing old vlan
+    - net: hns3: don't push link state to VF if unalive
+    - net: hns3: fix tm port shapping of fibre port is incorrect after driver
+      initialization
+    - nvme: add device name to warning in uuid_show()
+    - mlxsw: spectrum_cnt: Reorder counter pools
+    - net: bgmac: Fix an erroneous kfree() in bgmac_remove()
+    - net: ax25: Fix deadlock caused by skb_recv_datagram in ax25_recvmsg
+    - arm64: ftrace: fix branch range checks
+    - arm64: ftrace: consistently handle PLTs.
+    - certs/blacklist_hashes.c: fix const confusion in certs blacklist
+    - init: Initialize noop_backing_dev_info early
+    - block: Fix handling of offline queues in blk_mq_alloc_request_hctx()
+    - faddr2line: Fix overlapping text section failures, the sequel
+    - i2c: npcm7xx: Add check for platform_driver_register
+    - irqchip/gic/realview: Fix refcount leak in realview_gic_of_init
+    - irqchip/gic-v3: Fix error handling in gic_populate_ppi_partitions
+    - irqchip/gic-v3: Fix refcount leak in gic_populate_ppi_partitions
+    - irqchip/realtek-rtl: Fix refcount leak in map_interrupts
+    - sched: Fix balance_push() vs __sched_setscheduler()
+    - i2c: designware: Use standard optional ref clock implementation
+    - mei: hbm: drop capability response on early shutdown
+    - mei: me: add raptor lake point S DID
+    - comedi: vmk80xx: fix expression for tx buffer size
+    - [Config] updateconfigs for LIB_MEMNEQ
+    - crypto: memneq - move into lib/
+    - USB: serial: option: add support for Cinterion MV31 with new baseline
+    - USB: serial: io_ti: add Agilent E5805A support
+    - usb: dwc2: Fix memory leak in dwc2_hcd_init
+    - usb: cdnsp: Fixed setting last_trb incorrectly
+    - usb: gadget: lpc32xx_udc: Fix refcount leak in lpc32xx_udc_probe
+    - usb: gadget: f_fs: change ep->status safe in ffs_epfile_io()
+    - usb: gadget: f_fs: change ep->ep safe in ffs_epfile_io()
+    - tty: n_gsm: Debug output allocation must use GFP_ATOMIC
+    - serial: 8250: Store to lsr_save_flags after lsr read
+    - bus: fsl-mc-bus: fix KASAN use-after-free in fsl_mc_bus_remove()
+    - dm mirror log: round up region bitmap size to BITS_PER_LONG
+    - drm/amd/display: Cap OLED brightness per max frame-average luminance
+    - cfi: Fix __cfi_slowpath_diag RCU usage with cpuidle
+    - ext4: fix super block checksum incorrect after mount
+    - ext4: fix bug_on ext4_mb_use_inode_pa
+    - ext4: make variable "count" signed
+    - ext4: add reserved GDT blocks check
+    - KVM: arm64: Don't read a HW interrupt pending state in user context
+    - virtio-pci: Remove wrong address verification in vp_del_vqs()
+    - powerpc/book3e: get rid of #include <generated/compile.h>
+    - clk: imx8mp: fix usb_root_clk parent
+    - Linux 5.15.49
+
+  * Jammy update: v5.15.48 upstream stable release (LP: #1983146)
+    - Linux 5.15.48
+    - Upstream stable to v5.15.48
+
+  * Jammy update: v5.15.47 upstream stable release (LP: #1982968)
+    - pcmcia: db1xxx_ss: restrict to MIPS_DB1XXX boards
+    - staging: greybus: codecs: fix type confusion of list iterator variable
+    - iio: adc: ad7124: Remove shift from scan_type
+    - lkdtm/bugs: Check for the NULL pointer after calling kmalloc
+    - lkdtm/bugs: Don't expect thread termination without CONFIG_UBSAN_TRAP
+    - tty: goldfish: Use tty_port_destroy() to destroy port
+    - tty: serial: owl: Fix missing clk_disable_unprepare() in owl_uart_probe
+    - tty: n_tty: Restore EOF push handling behavior
+    - serial: 8250_aspeed_vuart: Fix potential NULL dereference in
+      aspeed_vuart_probe
+    - tty: serial: fsl_lpuart: fix potential bug when using both of_alias_get_id
+      and ida_simple_get
+    - remoteproc: imx_rproc: Ignore create mem entry for resource table
+    - usb: usbip: fix a refcount leak in stub_probe()
+    - usb: usbip: add missing device lock on tweak configuration cmd
+    - USB: storage: karma: fix rio_karma_init return
+    - usb: musb: Fix missing of_node_put() in omap2430_probe
+    - staging: fieldbus: Fix the error handling path in
+      anybuss_host_common_probe()
+    - pwm: lp3943: Fix duty calculation in case period was clamped
+    - pwm: raspberrypi-poe: Fix endianness in firmware struct
+    - rpmsg: qcom_smd: Fix irq_of_parse_and_map() return value
+    - usb: dwc3: gadget: Replace list_for_each_entry_safe() if using giveback
+    - usb: dwc3: pci: Fix pm_runtime_get_sync() error checking
+    - misc: fastrpc: fix an incorrect NULL check on list iterator
+    - firmware: stratix10-svc: fix a missing check on list iterator
+    - usb: typec: mux: Check dev_set_name() return value
+    - rpmsg: virtio: Fix possible double free in rpmsg_probe()
+    - rpmsg: virtio: Fix possible double free in rpmsg_virtio_add_ctrl_dev()
+    - rpmsg: virtio: Fix the unregistration of the device rpmsg_ctrl
+    - iio: adc: stmpe-adc: Fix wait_for_completion_timeout return value check
+    - iio: proximity: vl53l0x: Fix return value check of
+      wait_for_completion_timeout
+    - iio: adc: sc27xx: fix read big scale voltage not right
+    - iio: adc: sc27xx: Fine tune the scale calibration values
+    - rpmsg: qcom_smd: Fix returning 0 if irq_of_parse_and_map() fails
+    - pvpanic: Fix typos in the comments
+    - misc/pvpanic: Convert regular spinlock into trylock on panic path
+    - phy: qcom-qmp: fix pipe-clock imbalance on power-on failure
+    - power: supply: axp288_fuel_gauge: Drop BIOS version check from "T3 MRD" DMI
+      quirk
+    - serial: sifive: Report actual baud base rather than fixed 115200
+    - export: fix string handling of namespace in EXPORT_SYMBOL_NS
+    - soundwire: intel: prevent pm_runtime resume prior to system suspend
+    - coresight: cpu-debug: Replace mutex with mutex_trylock on panic notifier
+    - ksmbd: fix reference count leak in smb_check_perm_dacl()
+    - extcon: ptn5150: Add queue work sync before driver release
+    - soc: rockchip: Fix refcount leak in rockchip_grf_init
+    - clocksource/drivers/riscv: Events are stopped during CPU suspend
+    - ARM: dts: aspeed: ast2600-evb: Enable RX delay for MAC0/MAC1
+    - rtc: mt6397: check return value after calling platform_get_resource()
+    - rtc: ftrtc010: Use platform_get_irq() to get the interrupt
+    - rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
+    - staging: r8188eu: add check for kzalloc
+    - tty: n_gsm: Don't ignore write return value in gsmld_output()
+    - tty: n_gsm: Fix packet data hex dump output
+    - serial: meson: acquire port->lock in startup()
+    - serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
+    - serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
+    - serial: digicolor-usart: Don't allow CS5-6
+    - serial: rda-uart: Don't allow CS5-6
+    - serial: txx9: Don't allow CS5-6
+    - serial: sh-sci: Don't allow CS5-6
+    - serial: sifive: Sanitize CSIZE and c_iflag
+    - serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
+    - serial: stm32-usart: Correct CSIZE, bits, and parity
+    - firmware: dmi-sysfs: Fix memory leak in dmi_sysfs_register_handle
+    - bus: ti-sysc: Fix warnings for unbind for serial
+    - driver: base: fix UAF when driver_attach failed
+    - driver core: fix deadlock in __device_attach
+    - watchdog: rti-wdt: Fix pm_runtime_get_sync() error checking
+    - watchdog: ts4800_wdt: Fix refcount leak in ts4800_wdt_probe
+    - blk-mq: don't touch ->tagset in blk_mq_get_sq_hctx
+    - ASoC: fsl_sai: Fix FSL_SAI_xDR/xFR definition
+    - clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
+    - s390/crypto: fix scatterwalk_unmap() callers in AES-GCM
+    - net: sched: fixed barrier to prevent skbuff sticking in qdisc backlog
+    - net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry()
+    - net: ethernet: ti: am65-cpsw-nuss: Fix some refcount leaks
+    - net: dsa: mv88e6xxx: Fix refcount leak in mv88e6xxx_mdios_register
+    - modpost: fix removing numeric suffixes
+    - jffs2: fix memory leak in jffs2_do_fill_super
+    - ubi: fastmap: Fix high cpu usage of ubi_bgt by making sure wl_pool not empty
+    - ubi: ubi_create_volume: Fix use-after-free when volume creation failed
+    - selftests/bpf: fix selftest after random: Urandom_read tracepoint removal
+    - selftests/bpf: fix stacktrace_build_id with missing kprobe/urandom_read
+    - bpf: Fix probe read error in ___bpf_prog_run()
+    - block: take destination bvec offsets into account in bio_copy_data_iter
+    - riscv: read-only pages should not be writable
+    - net/smc: fixes for converting from "struct smc_cdc_tx_pend **" to "struct
+      smc_wr_tx_pend_priv *"
+    - tcp: add accessors to read/set tp->snd_cwnd
+    - nfp: only report pause frame configuration for physical device
+    - sfc: fix considering that all channels have TX queues
+    - sfc: fix wrong tx channel offset with efx_separate_tx_channels
+    - block: make bioset_exit() fully resilient against being called twice
+    - vdpa: Fix error logic in vdpa_nl_cmd_dev_get_doit
+    - virtio: pci: Fix an error handling path in vp_modern_probe()
+    - net/mlx5: Don't use already freed action pointer
+    - net/mlx5: CT: Fix header-rewrite re-use for tupels
+    - net/mlx5: correct ECE offset in query qp output
+    - net/mlx5e: Update netdev features after changing XDP state
+    - net: sched: add barrier to fix packet stuck problem for lockless qdisc
+    - tcp: tcp_rtx_synack() can be called from process context
+    - vdpa: ifcvf: set pci driver data in probe
+    - octeontx2-af: fix error code in is_valid_offset()
+    - s390/mcck: isolate SIE instruction when setting CIF_MCCK_GUEST flag
+    - regulator: mt6315-regulator: fix invalid allowed mode
+    - gpio: pca953x: use the correct register address to do regcache sync
+    - afs: Fix infinite loop found by xfstest generic/676
+    - scsi: sd: Fix potential NULL pointer dereference
+    - tipc: check attribute length for bearer name
+    - driver core: Fix wait_for_device_probe() & deferred_probe_timeout
+      interaction
+    - perf c2c: Fix sorting in percent_rmt_hitm_cmp()
+    - dmaengine: idxd: set DMA_INTERRUPT cap bit
+    - mips: cpc: Fix refcount leak in mips_cpc_default_phys_base
+    - bootconfig: Make the bootconfig.o as a normal object file
+    - tracing: Make tp_printk work on syscall tracepoints
+    - tracing: Fix sleeping function called from invalid context on RT kernel
+    - tracing: Avoid adding tracer option before update_tracer_options
+    - iommu/arm-smmu: fix possible null-ptr-deref in arm_smmu_device_probe()
+    - iommu/arm-smmu-v3: check return value after calling platform_get_resource()
+    - f2fs: remove WARN_ON in f2fs_is_valid_blkaddr
+    - i2c: cadence: Increase timeout per message if necessary
+    - m68knommu: set ZERO_PAGE() to the allocated zeroed page
+    - m68knommu: fix undefined reference to `_init_sp'
+    - dmaengine: zynqmp_dma: In struct zynqmp_dma_chan fix desc_size data type
+    - NFSv4: Don't hold the layoutget locks across multiple RPC calls
+    - video: fbdev: hyperv_fb: Allow resolutions with size > 64 MB for Gen1
+    - video: fbdev: pxa3xx-gcu: release the resources correctly in
+      pxa3xx_gcu_probe/remove()
+    - RISC-V: use memcpy for kexec_file mode
+    - m68knommu: fix undefined reference to `mach_get_rtc_pll'
+    - f2fs: fix to tag gcing flag on page during file defragment
+    - xprtrdma: treat all calls not a bcall when bc_serv is NULL
+    - drm/bridge: sn65dsi83: Fix an error handling path in sn65dsi83_probe()
+    - drm/bridge: ti-sn65dsi83: Handle dsi_lanes == 0 as invalid
+    - netfilter: nat: really support inet nat without l3 address
+    - netfilter: nf_tables: use kfree_rcu(ptr, rcu) to release hooks in clean_net
+      path
+    - netfilter: nf_tables: delete flowtable hooks via transaction list
+    - powerpc/kasan: Force thread size increase with KASAN
+    - SUNRPC: Trap RDMA segment overflows
+    - netfilter: nf_tables: always initialize flowtable hook list in transaction
+    - ata: pata_octeon_cf: Fix refcount leak in octeon_cf_probe
+    - netfilter: nf_tables: release new hooks on unsupported flowtable flags
+    - netfilter: nf_tables: memleak flow rule from commit path
+    - netfilter: nf_tables: bail out early if hardware offload is not supported
+    - xen: unexport __init-annotated xen_xlate_map_ballooned_pages()
+    - stmmac: intel: Fix an error handling path in intel_eth_pci_probe()
+    - af_unix: Fix a data-race in unix_dgram_peer_wake_me().
+    - bpf, arm64: Clear prog->jited_len along prog->jited
+    - net: dsa: lantiq_gswip: Fix refcount leak in gswip_gphy_fw_list
+    - net/mlx4_en: Fix wrong return value on ioctl EEPROM query failure
+    - i40e: xsk: Move tmp desc array from driver to pool
+    - xsk: Fix handling of invalid descriptors in XSK TX batching API
+    - SUNRPC: Fix the calculation of xdr->end in xdr_get_next_encode_buffer()
+    - net: mdio: unexport __init-annotated mdio_bus_init()
+    - net: xfrm: unexport __init-annotated xfrm4_protocol_init()
+    - net: ipv6: unexport __init-annotated seg6_hmac_init()
+    - net/mlx5: Lag, filter non compatible devices
+    - net/mlx5: Fix mlx5_get_next_dev() peer device matching
+    - net/mlx5: Rearm the FW tracer after each tracer event
+    - net/mlx5: fs, fail conflicting actions
+    - ip_gre: test csum_start instead of transport header
+    - net: altera: Fix refcount leak in altera_tse_mdio_create
+    - net: dsa: mv88e6xxx: use BMSR_ANEGCOMPLETE bit for filling an_complete
+    - tcp: use alloc_large_system_hash() to allocate table_perturb
+    - drm: imx: fix compiler warning with gcc-12
+    - nfp: flower: restructure flow-key for gre+vlan combination
+    - iov_iter: Fix iter_xarray_get_pages{,_alloc}()
+    - iio: dummy: iio_simple_dummy: check the return value of kstrdup()
+    - staging: rtl8712: fix a potential memory leak in r871xu_drv_init()
+    - iio: st_sensors: Add a local lock for protecting odr
+    - lkdtm/usercopy: Expand size of "out of frame" object
+    - drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback()
+    - drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()
+    - tty: synclink_gt: Fix null-pointer-dereference in slgt_clean()
+    - tty: Fix a possible resource leak in icom_probe
+    - thunderbolt: Use different lane for second DisplayPort tunnel
+    - drivers: staging: rtl8192u: Fix deadlock in ieee80211_beacons_stop()
+    - drivers: staging: rtl8192e: Fix deadlock in rtllib_beacons_stop()
+    - USB: host: isp116x: check return value after calling platform_get_resource()
+    - drivers: tty: serial: Fix deadlock in sa1100_set_termios()
+    - drivers: usb: host: Fix deadlock in oxu_bus_suspend()
+    - USB: hcd-pci: Fully suspend across freeze/thaw cycle
+    - char: xillybus: fix a refcount leak in cleanup_dev()
+    - sysrq: do not omit current cpu when showing backtrace of all active CPUs
+    - usb: dwc2: gadget: don't reset gadget's driver->bus
+    - soundwire: qcom: adjust autoenumeration timeout
+    - misc: rtsx: set NULL intfdata when probe fails
+    - extcon: Fix extcon_get_extcon_dev() error handling
+    - extcon: Modify extcon device to be created after driver data is set
+    - clocksource/drivers/sp804: Avoid error on multiple instances
+    - staging: rtl8712: fix uninit-value in usb_read8() and friends
+    - staging: rtl8712: fix uninit-value in r871xu_drv_init()
+    - serial: msm_serial: disable interrupts in __msm_console_write()
+    - kernfs: Separate kernfs_pr_cont_buf and rename_lock.
+    - watchdog: wdat_wdt: Stop watchdog when rebooting the system
+    - md: protect md_unregister_thread from reentrancy
+    - scsi: myrb: Fix up null pointer access on myrb_cleanup()
+    - ceph: allow ceph.dir.rctime xattr to be updatable
+    - ceph: flush the mdlog for filesystem sync
+    - drm/amd/display: Check if modulo is 0 before dividing.
+    - drm/radeon: fix a possible null pointer dereference
+    - drm/amd/pm: Fix missing thermal throttler status
+    - um: line: Use separate IRQs per line
+    - modpost: fix undefined behavior of is_arm_mapping_symbol()
+    - x86/cpu: Elide KCSAN for cpu_has() and friends
+    - jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
+    - nbd: call genl_unregister_family() first in nbd_cleanup()
+    - nbd: fix race between nbd_alloc_config() and module removal
+    - cifs: version operations for smb20 unneeded when legacy support disabled
+    - drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
+    - nodemask: Fix return values to be unsigned
+    - vringh: Fix loop descriptors check in the indirect cases
+    - scripts/gdb: change kernel config dumping method
+    - ALSA: usb-audio: Skip generic sync EP parse for secondary EP
+    - ALSA: usb-audio: Set up (implicit) sync for Saffire 6
+    - ALSA: hda/conexant - Fix loopback issue with CX20632
+    - ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo Yoga
+      DuetITL 2021
+    - ALSA: hda/realtek: Add quirk for HP Dev One
+    - cifs: return errors during session setup during reconnects
+    - cifs: fix reconnect on smb3 mount types
+    - KEYS: trusted: tpm2: Fix migratable logic
+    - ata: libata-transport: fix {dma|pio|xfer}_mode sysfs files
+    - mmc: block: Fix CQE recovery reset success
+    - net: phy: dp83867: retrigger SGMII AN when link change
+    - writeback: Fix inode->i_io_list not be protected by inode->i_lock error
+    - nfc: st21nfca: fix incorrect validating logic in EVT_TRANSACTION
+    - nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
+    - nfc: st21nfca: fix incorrect sizing calculations in EVT_TRANSACTION
+    - ixgbe: fix bcast packets Rx on VF after promisc removal
+    - ixgbe: fix unexpected VLAN Rx in promisc mode on VF
+    - Input: bcm5974 - set missing URB_NO_TRANSFER_DMA_MAP urb flag
+    - vduse: Fix NULL pointer dereference on sysfs access
+    - powerpc: Don't select HAVE_IRQ_EXIT_ON_IRQ_STACK
+    - drm/bridge: analogix_dp: Support PSR-exit to disable transition
+    - drm/atomic: Force bridge self-refresh-exit on CRTC switch
+    - drm/amdgpu: update VCN codec support for Yellow Carp
+    - powerpc/32: Fix overread/overwrite of thread_struct via ptrace
+    - powerpc/mm: Switch obsolete dssall to .long
+    - drm/ast: Create threshold values for AST2600
+    - random: avoid checking crng_ready() twice in random_init()
+    - random: mark bootloader randomness code as __init
+    - random: account for arch randomness in bits
+    - md/raid0: Ignore RAID0 layout if the second zone has only one device
+    - net/sched: act_police: more accurate MTU policing
+    - PCI: qcom: Fix pipe clock imbalance
+    - zonefs: fix handling of explicit_open option on mount
+    - iov_iter: fix build issue due to possible type mis-match
+    - dmaengine: idxd: add missing callback function to support DMA_INTERRUPT
+    - tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd
+    - xsk: Fix possible crash when multiple sockets are created
+    - Linux 5.15.47
+
+  * CVE-2022-36946
+    - netfilter: nf_queue: do not allow packet truncation below transport header
+      offset
+
+  * CVE-2021-33655
+    - fbcon: Disallow setting font bigger than screen size
+    - fbcon: Prevent that screen size is smaller than font size
+    - fbmem: Check virtual screen sizes in fb_set_var()
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 26 Aug 2022 11:12:42 +0200
+
+linux (5.15.0-47.51) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-47.51 -proposed tracker (LP: #1983903)
+
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - UBUNTU: [Packaging] Move python3-dev to build-depends
+
+  * touchpad and touchscreen doesn't work at all on ACER Spin 5 (SP513-54N)
+    (LP: #1884232)
+    - x86/PCI: Eliminate remove_e820_regions() common subexpressions
+    - x86: Log resource clipping for E820 regions
+    - x86/PCI: Clip only host bridge windows for E820 regions
+    - x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
+    - x86/PCI: Disable E820 reserved region clipping via quirks
+    - x86/PCI: Revert "x86/PCI: Clip only host bridge windows for E820 regions"
+
+  * [SRU][H/OEM-5.13/OEM-5.14/U][J/OEM-5.17/U] Fix invalid MAC address after
+    hotplug tbt dock (LP: #1942999)
+    - SAUCE: igc: wait for the MAC copy when enabled MAC passthrough
+
+  * Mass Storage Gadget driver truncates device >2TB (LP: #1981390)
+    - usb: gadget: storage: add support for media larger than 2T
+
+  * AMD Rembrandt: DP tunneling fails with Thunderbolt monitors (LP: #1983143)
+    - SAUCE: drm/amd: Fix DP Tunneling with Thunderbolt monitors
+    - drm/amd/display: Fix for dmub outbox notification enable
+    - Revert "drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset"
+    - drm/amd/display: Reset link encoder assignments for GPU reset
+    - drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset
+    - drm/amd/display: Fix new dmub notification enabling in DM
+    - SAUCE: thunderbolt: Add DP out resource when DP tunnel is discovered.
+
+  * Fix sub-optimal I210 network speed (LP: #1976438)
+    - igb: Make DMA faster when CPU is active on the PCIe link
+
+  * e1000e report hardware hang (LP: #1973104)
+    - e1000e: Enable GPT clock before sending message to CSME
+    - Revert "e1000e: Fix possible HW unit hang after an s0ix exit"
+
+  * ioam6.sh in net from ubuntu_kernel_selftests fails with 5.15 kernels in
+    Focal (LP: #1982930)
+    - selftests: net: fix IOAM test skip return code
+
+  * Additional fix for TGL + AUO panel flickering (LP: #1983297)
+    - Revert "UBUNTU: SAUCE: drm/i915/display/psr: Fix flicker on TGL + AUO panel"
+    - drm/i915/display: Fix sel fetch plane offset calculation
+    - drm/i915: Nuke ORIGIN_GTT
+    - drm/i915/display: Drop PSR support from HSW and BDW
+    - drm/i915/display/psr: Handle plane and pipe restrictions at every page flip
+    - drm/i915/display/psr: Do full fetch when handling multi-planar formats
+    - drm/i915/display: Drop unnecessary frontbuffer flushes
+    - drm/i915/display: Handle frontbuffer rendering when PSR2 selective fetch is
+      enabled
+    - drm/i915/display: Fix glitches when moving cursor with PSR2 selective fetch
+      enabled
+    - SAUCE: drm/i915/display/psr: Reinstate fix for TGL + AUO panel flicker
+
+  * AMD Yellow Carp DMCUB fw update for s0i3 B0 fixes (LP: #1957026)
+    - drm/amd/display: Optimize bandwidth on following fast update
+    - drm/amd/display: Fix surface optimization regression on Carrizo
+    - drm/amd/display: Reset DMCUB before HW init
+
+  * GPIO character device v1 API not enabled in kernel (LP: #1953613)
+    - [Config] Enable CONFIG_GPIO_CDEV_V1
+
+  * intel_iommu: Fix  enable intel_iommu, Ubuntu 22.04 installation crashes
+    (LP: #1982104)
+    - iommu/vt-d: Fix RID2PASID setup/teardown failure
+
+  * Headset mic with Cirrus logic codec doesn't work (LP: #1972815)
+    - ASoC: cs42l42: Move CS42L42 register descriptions to general include
+    - ALSA: hda/cs8409: Use general cs42l42 include in cs8409 hda driver
+    - ALSA: hda/cs8409: Support manual mode detection for CS42L42
+
+  * Failed to resume from S3 blocked by atlantic driver[1d6a:94c0]
+    (LP: #1981950)
+    - net: atlantic: remove deep parameter on suspend/resume functions
+    - net: atlantic: remove aq_nic_deinit() when resume
+
+  * Make cm32181 sensor work after system suspend (LP: #1981773)
+    - iio: light: cm32181: Add PM support
+
+  * Clear PCI errors left from BIOS (LP: #1981173)
+    - PCI: Clear PCI_STATUS when setting up device
+
+  * Fix AMDGPU blank screen when Type-C DP alt is in use (LP: #1980060)
+    - drm/amd/display: Query DMCUB for dp alt status
+    - drm/amd/display: Add version check before using DP alt query interface
+
+  * Fix WD22TB4 suspend and resume, two external monitor can not output
+    (LP: #1979267)
+    - drm/dp/mst: Read the extended DPCD capabilities during system resume
+
+  * [SRU] bcache deadlock during read IO in writeback mode (LP: #1980925)
+    - bcache: memset on stack variables in bch_btree_check() and
+      bch_sectors_dirty_init()
+
+  * Audio mute key (f5) LED and Mic mute key (f8) LED are no function on HP
+    440/450/640/650 G9 (LP: #1982716)
+    - ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
+
+  * Enable WiFi hotspot feature for MediaTek MT7921 (LP: #1979173)
+    - mt76: mt7921: Add AP mode support
+    - mt76: mt7921: not support beacon offload disable command
+    - mt76: mt7921: fix command timeout in AP stop period
+
+  * Fix drm/amd/pm: enable ASPM by default (LP: #1966680)
+    - drm/amd: Refactor `amdgpu_aspm` to be evaluated per device
+    - drm/amd: Use amdgpu_device_should_use_aspm on navi umd pstate switching
+    - drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems
+
+  * Power cycle USB ports on shutdown/reboot (LP: #1976503)
+    - xhci: turn off port power in shutdown
+
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - binfmt_flat: do not stop relocating GOT entries prematurely on riscv
+    - parisc/stifb: Implement fb_is_primary_device()
+    - parisc/stifb: Keep track of hardware path of graphics card
+    - RISC-V: Mark IORESOURCE_EXCLUSIVE for reserved mem instead of
+      IORESOURCE_BUSY
+    - riscv: Initialize thread pointer before calling C functions
+    - riscv: Fix irq_work when SMP is disabled
+    - riscv: Wire up memfd_secret in UAPI header
+    - riscv: Move alternative length validation into subsection
+    - ALSA: hda/realtek - Add new type for ALC245
+    - ALSA: hda/realtek: Enable 4-speaker output for Dell XPS 15 9520 laptop
+    - ALSA: hda/realtek - Fix microphone noise on ASUS TUF B550M-PLUS
+    - ALSA: usb-audio: Cancel pending work at closing a MIDI substream
+    - USB: serial: option: add Quectel BG95 modem
+    - USB: new quirk for Dell Gen 2 devices
+    - usb: isp1760: Fix out-of-bounds array access
+    - usb: dwc3: gadget: Move null pinter check to proper place
+    - usb: core: hcd: Add support for deferring roothub registration
+    - fs/ntfs3: Update valid size if -EIOCBQUEUED
+    - fs/ntfs3: Fix fiemap + fix shrink file size (to remove preallocated space)
+    - fs/ntfs3: Keep preallocated only if option prealloc enabled
+    - fs/ntfs3: Check new size for limits
+    - fs/ntfs3: In function ntfs_set_acl_ex do not change inode->i_mode if called
+      from function ntfs_init_acl
+    - fs/ntfs3: Fix some memory leaks in an error handling path of 'log_replay()'
+    - fs/ntfs3: Update i_ctime when xattr is added
+    - fs/ntfs3: Restore ntfs_xattr_get_acl and ntfs_xattr_set_acl functions
+    - cifs: fix potential double free during failed mount
+    - cifs: when extending a file with falloc we should make files not-sparse
+    - xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
+    - platform/x86: intel-hid: fix _DSM function index handling
+    - x86/MCE/AMD: Fix memory leak when threshold_create_bank() fails
+    - perf/x86/intel: Fix event constraints for ICL
+    - x86/kexec: fix memory leak of elf header buffer
+    - x86/sgx: Set active memcg prior to shmem allocation
+    - ptrace/um: Replace PT_DTRACE with TIF_SINGLESTEP
+    - ptrace/xtensa: Replace PT_SINGLESTEP with TIF_SINGLESTEP
+    - ptrace: Reimplement PTRACE_KILL by always sending SIGKILL
+    - btrfs: add "0x" prefix for unsupported optional features
+    - btrfs: return correct error number for __extent_writepage_io()
+    - btrfs: repair super block num_devices automatically
+    - btrfs: fix the error handling for submit_extent_page() for
+      btrfs_do_readpage()
+    - iommu/vt-d: Add RPLS to quirk list to skip TE disabling
+    - drm/vmwgfx: validate the screen formats
+    - drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes
+    - selftests/bpf: Fix vfs_link kprobe definition
+    - selftests/bpf: Fix parsing of prog types in UAPI hdr for bpftool sync
+    - mwifiex: add mutex lock for call in mwifiex_dfs_chan_sw_work_queue
+    - b43legacy: Fix assigning negative value to unsigned variable
+    - b43: Fix assigning negative value to unsigned variable
+    - ipw2x00: Fix potential NULL dereference in libipw_xmit()
+    - ipv6: fix locking issues with loops over idev->addr_list
+    - fbcon: Consistently protect deferred_takeover with console_lock()
+    - x86/platform/uv: Update TSC sync state for UV5
+    - ACPICA: Avoid cache flush inside virtual machines
+    - mac80211: minstrel_ht: fix where rate stats are stored (fixes debugfs
+      output)
+    - drm/komeda: return early if drm_universal_plane_init() fails.
+    - drm/amd/display: Disabling Z10 on DCN31
+    - rcu-tasks: Fix race in schedule and flush work
+    - rcu: Make TASKS_RUDE_RCU select IRQ_WORK
+    - sfc: ef10: Fix assigning negative value to unsigned variable
+    - ALSA: jack: Access input_dev under mutex
+    - spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA
+      direction
+    - tools/power turbostat: fix ICX DRAM power numbers
+    - scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg()
+    - scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock
+    - scsi: lpfc: Fix call trace observed during I/O with CMF enabled
+    - cpuidle: PSCI: Improve support for suspend-to-RAM for PSCI OSI mode
+    - drm/amd/pm: fix double free in si_parse_power_table()
+    - ASoC: rsnd: care default case on rsnd_ssiu_busif_err_status_clear()
+    - ASoC: rsnd: care return value from rsnd_node_fixed_index()
+    - ath9k: fix QCA9561 PA bias level
+    - media: venus: hfi: avoid null dereference in deinit
+    - media: pci: cx23885: Fix the error handling in cx23885_initdev()
+    - media: cx25821: Fix the warning when removing the module
+    - md/bitmap: don't set sb values if can't pass sanity check
+    - mmc: jz4740: Apply DMA engine limits to maximum segment size
+    - drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit
+    - scsi: megaraid: Fix error check return value of register_chrdev()
+    - drm/amdgpu/sdma: Fix incorrect calculations of the wptr of the doorbells
+    - scsi: ufs: Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync()
+    - scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp()
+    - ath11k: disable spectral scan during spectral deinit
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the HP Pro Tablet 408
+    - drm/plane: Move range check for format_count earlier
+    - drm/amd/pm: fix the compile warning
+    - ath10k: skip ath10k_halt during suspend for driver state RESTARTING
+    - arm64: compat: Do not treat syscall number as ESR_ELx for a bad syscall
+    - drm: msm: fix error check return value of irq_of_parse_and_map()
+    - scsi: target: tcmu: Fix possible data corruption
+    - ipv6: Don't send rs packets to the interface of ARPHRD_TUNNEL
+    - net/mlx5: fs, delete the FTE when there are no rules attached to it
+    - ASoC: dapm: Don't fold register value changes into notifications
+    - mlxsw: spectrum_dcb: Do not warn about priority changes
+    - mlxsw: Treat LLDP packets as control
+    - drm/amdgpu/psp: move PSP memory alloc from hw_init to sw_init
+    - drm/amdgpu/ucode: Remove firmware load type check in amdgpu_ucode_free_bo
+    - regulator: mt6315: Enforce regulator-compatible, not name
+    - HID: bigben: fix slab-out-of-bounds Write in bigben_probe
+    - of: Support more than one crash kernel regions for kexec -s
+    - ASoC: tscs454: Add endianness flag in snd_soc_component_driver
+    - scsi: lpfc: Alter FPIN stat accounting logic
+    - net: remove two BUG() from skb_checksum_help()
+    - s390/preempt: disable __preempt_count_add() optimization for
+      PROFILE_ALL_BRANCHES
+    - perf/amd/ibs: Cascade pmu init functions' return value
+    - sched/core: Avoid obvious double update_rq_clock warning
+    - spi: stm32-qspi: Fix wait_cmd timeout in APM mode
+    - dma-debug: change allocation mode from GFP_NOWAIT to GFP_ATIOMIC
+    - ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default
+    - ipmi:ssif: Check for NULL msg when handling events and messages
+    - ipmi: Fix pr_fmt to avoid compilation issues
+    - rtlwifi: Use pr_warn instead of WARN_ONCE
+    - mt76: mt7921: accept rx frames with non-standard VHT MCS10-11
+    - mt76: fix encap offload ethernet type check
+    - media: rga: fix possible memory leak in rga_probe
+    - media: coda: limit frame interval enumeration to supported encoder frame
+      sizes
+    - media: hantro: HEVC: unconditionnaly set pps_{cb/cr}_qp_offset values
+    - media: ccs-core.c: fix failure to call clk_disable_unprepare
+    - media: imon: reorganize serialization
+    - media: cec-adap.c: fix is_configuring state
+    - usbnet: Run unregister_netdev() before unbind() again
+    - openrisc: start CPU timer early in boot
+    - nvme-pci: fix a NULL pointer dereference in nvme_alloc_admin_tags
+    - ASoC: rt5645: Fix errorenous cleanup order
+    - nbd: Fix hung on disconnect request if socket is closed before
+    - drm/amd/pm: update smartshift powerboost calc for smu12
+    - drm/amd/pm: update smartshift powerboost calc for smu13
+    - net: phy: micrel: Allow probing without .driver_data
+    - media: exynos4-is: Fix compile warning
+    - media: hantro: Stop using H.264 parameter pic_num
+    - ASoC: max98357a: remove dependency on GPIOLIB
+    - ASoC: rt1015p: remove dependency on GPIOLIB
+    - ACPI: CPPC: Assume no transition latency if no PCCT
+    - nvme: set non-mdts limits in nvme_scan_work
+    - can: mcp251xfd: silence clang's -Wunaligned-access warning
+    - x86/microcode: Add explicit CPU vendor dependency
+    - net: ipa: ignore endianness if there is no header
+    - m68k: atari: Make Atari ROM port I/O write macros return void
+    - rxrpc: Return an error to sendmsg if call failed
+    - rxrpc, afs: Fix selection of abort codes
+    - afs: Adjust ACK interpretation to try and cope with NAT
+    - eth: tg3: silence the GCC 12 array-bounds warning
+    - char: tpm: cr50_i2c: Suppress duplicated error message in .remove()
+    - selftests/bpf: fix btf_dump/btf_dump due to recent clang change
+    - gfs2: use i_lock spin_lock for inode qadata
+    - scsi: target: tcmu: Avoid holding XArray lock when calling lock_page
+    - IB/rdmavt: add missing locks in rvt_ruc_loopback
+    - ARM: dts: ox820: align interrupt controller node name with dtschema
+    - ARM: dts: socfpga: align interrupt controller node name with dtschema
+    - ARM: dts: s5pv210: align DMA channels with dtschema
+    - arm64: dts: qcom: msm8994: Fix the cont_splash_mem address
+    - arm64: dts: qcom: msm8994: Fix BLSP[12]_DMA channels count
+    - PM / devfreq: rk3399_dmc: Disable edev on remove()
+    - crypto: ccree - use fine grained DMA mapping dir
+    - soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc
+    - fs: jfs: fix possible NULL pointer dereference in dbFree()
+    - arm64: dts: qcom: sdm845-xiaomi-beryllium: fix typo in panel's vddio-supply
+      property
+    - ALSA: usb-audio: Add quirk bits for enabling/disabling generic implicit fb
+    - ALSA: usb-audio: Move generic implicit fb quirk entries into quirks.c
+    - ARM: OMAP1: clock: Fix UART rate reporting algorithm
+    - powerpc/fadump: Fix fadump to work with a different endian capture kernel
+    - fat: add ratelimit to fat*_ent_bread()
+    - pinctrl: renesas: rzn1: Fix possible null-ptr-deref in
+      sh_pfc_map_resources()
+    - ARM: versatile: Add missing of_node_put in dcscb_init
+    - ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROM
+    - ARM: hisi: Add missing of_node_put after of_find_compatible_node
+    - cpufreq: Avoid unnecessary frequency updates due to mismatch
+    - powerpc/rtas: Keep MSR[RI] set when calling RTAS
+    - PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
+    - KVM: PPC: Book3S HV Nested: L2 LPCR should inherit L1 LPES setting
+    - alpha: fix alloc_zeroed_user_highpage_movable()
+    - tracing: incorrect isolate_mote_t cast in mm_vmscan_lru_isolate
+    - powerpc/powernv/vas: Assign real address to rx_fifo in vas_rx_win_attr
+    - powerpc/xics: fix refcount leak in icp_opal_init()
+    - powerpc/powernv: fix missing of_node_put in uv_init()
+    - macintosh/via-pmu: Fix build failure when CONFIG_INPUT is disabled
+    - powerpc/iommu: Add missing of_node_put in iommu_init_early_dart
+    - smb3: check for null tcon
+    - RDMA/hfi1: Prevent panic when SDMA is disabled
+    - Input: gpio-keys - cancel delayed work only in case of GPIO
+    - drm: fix EDID struct for old ARM OABI format
+    - drm/bridge_connector: enable HPD by default if supported
+    - dt-bindings: display: sitronix, st7735r: Fix backlight in example
+    - drm/vmwgfx: Fix an invalid read
+    - ath11k: acquire ab->base_lock in unassign when finding the peer by addr
+    - drm: bridge: it66121: Fix the register page length
+    - ath9k: fix ar9003_get_eepmisc
+    - drm/edid: fix invalid EDID extension block filtering
+    - drm/bridge: adv7511: clean up CEC adapter when probe fails
+    - drm: bridge: icn6211: Fix register layout
+    - drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling
+    - mtd: spinand: gigadevice: fix Quad IO for GD5F1GQ5UExxG
+    - spi: qcom-qspi: Add minItems to interconnect-names
+    - ASoC: mediatek: Fix error handling in mt8173_max98090_dev_probe
+    - ASoC: mediatek: Fix missing of_node_put in mt2701_wm8960_machine_probe
+    - x86/delay: Fix the wrong asm constraint in delay_loop()
+    - drm/vc4: hvs: Fix frame count register readout
+    - drm/mediatek: Fix mtk_cec_mask()
+    - drm/vc4: hvs: Reset muxes at probe time
+    - drm/vc4: txp: Don't set TXP_VSTART_AT_EOF
+    - drm/vc4: txp: Force alpha to be 0xff if it's disabled
+    - libbpf: Don't error out on CO-RE relos for overriden weak subprogs
+    - x86/PCI: Fix ALi M1487 (IBC) PIRQ router link value interpretation
+    - mptcp: reset the packet scheduler on PRIO change
+    - nl80211: show SSID for P2P_GO interfaces
+    - drm/komeda: Fix an undefined behavior bug in komeda_plane_add()
+    - drm: mali-dp: potential dereference of null pointer
+    - spi: spi-ti-qspi: Fix return value handling of wait_for_completion_timeout
+    - scftorture: Fix distribution of short handler delays
+    - net: dsa: mt7530: 1G can also support 1000BASE-X link mode
+    - ixp4xx_eth: fix error check return value of platform_get_irq()
+    - NFC: NULL out the dev->rfkill to prevent UAF
+    - efi: Add missing prototype for efi_capsule_setup_info
+    - device property: Check fwnode->secondary when finding properties
+    - device property: Allow error pointer to be passed to fwnode APIs
+    - target: remove an incorrect unmap zeroes data deduction
+    - drbd: fix duplicate array initializer
+    - EDAC/dmc520: Don't print an error for each unconfigured interrupt line
+    - mtd: rawnand: denali: Use managed device resources
+    - HID: hid-led: fix maximum brightness for Dream Cheeky
+    - HID: elan: Fix potential double free in elan_input_configured
+    - drm/bridge: Fix error handling in analogix_dp_probe
+    - regulator: da9121: Fix uninit-value in da9121_assign_chip_model()
+    - drm/mediatek: dpi: Use mt8183 output formats for mt8192
+    - signal: Deliver SIGTRAP on perf event asynchronously if blocked
+    - sched/fair: Fix cfs_rq_clock_pelt() for throttled cfs_rq
+    - sched/psi: report zeroes for CPU full at the system level
+    - spi: img-spfi: Fix pm_runtime_get_sync() error checking
+    - cpufreq: Fix possible race in cpufreq online error path
+    - printk: use atomic updates for klogd work
+    - printk: add missing memory barrier to wake_up_klogd()
+    - printk: wake waiters for safe and NMI contexts
+    - ath9k_htc: fix potential out of bounds access with invalid
+      rxstatus->rs_keyix
+    - media: i2c: max9286: Use dev_err_probe() helper
+    - media: i2c: max9286: Use "maxim,gpio-poc" property
+    - media: i2c: max9286: fix kernel oops when removing module
+    - media: hantro: Empty encoder capture buffers by default
+    - drm/panel: simple: Add missing bus flags for Innolux G070Y2-L01
+    - ALSA: pcm: Check for null pointer of pointer substream before dereferencing
+      it
+    - mtdblock: warn if opened on NAND
+    - inotify: show inotify mask flags in proc fdinfo
+    - fsnotify: fix wrong lockdep annotations
+    - spi: rockchip: Stop spi slave dma receiver when cs inactive
+    - spi: rockchip: Preset cs-high and clk polarity in setup progress
+    - spi: rockchip: fix missing error on unsupported SPI_CS_HIGH
+    - of: overlay: do not break notify on NOTIFY_{OK|STOP}
+    - selftests/damon: add damon to selftests root Makefile
+    - drm/msm/dp: Modify prototype of encoder based API
+    - drm/msm/hdmi: switch to drm_bridge_connector
+    - drm/msm/dpu: adjust display_v_end for eDP and DP
+    - scsi: iscsi: Fix harmless double shift bug
+    - scsi: ufs: qcom: Fix ufs_qcom_resume()
+    - scsi: ufs: core: Exclude UECxx from SFR dump list
+    - drm/v3d: Fix null pointer dereference of pointer perfmon
+    - selftests/resctrl: Fix null pointer dereference on open failed
+    - libbpf: Fix logic for finding matching program for CO-RE relocation
+    - mtd: spi-nor: core: Check written SR value in
+      spi_nor_write_16bit_sr_and_check()
+    - x86/pm: Fix false positive kmemleak report in msr_build_context()
+    - mtd: rawnand: cadence: fix possible null-ptr-deref in
+      cadence_nand_dt_probe()
+    - mtd: rawnand: intel: fix possible null-ptr-deref in ebu_nand_probe()
+    - x86/speculation: Add missing prototype for unpriv_ebpf_notify()
+    - ASoC: rk3328: fix disabling mclk on pclk probe failure
+    - perf tools: Add missing headers needed by util/data.h
+    - drm/msm/disp/dpu1: set vbif hw config to NULL to avoid use after memory free
+      during pm runtime resume
+    - drm/msm/dp: stop event kernel thread when DP unbind
+    - drm/msm/dp: fix error check return value of irq_of_parse_and_map()
+    - drm/msm/dp: reset DP controller before transmit phy test pattern
+    - drm/msm/dp: do not stop transmitting phy test pattern during DP phy
+      compliance test
+    - drm/msm/dsi: fix error checks and return values for DSI xmit functions
+    - drm/msm/hdmi: check return value after calling
+      platform_get_resource_byname()
+    - drm/msm/hdmi: fix error check return value of irq_of_parse_and_map()
+    - drm/msm: add missing include to msm_drv.c
+    - drm/panel: panel-simple: Fix proper bpc for AM-1280800N3TZQW-T00H
+    - kunit: fix debugfs code to use enum kunit_status, not bool
+    - drm/rockchip: vop: fix possible null-ptr-deref in vop_bind()
+    - spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA
+    - [Packaging] add python3-dev as build dependency
+    - perf tools: Use Python devtools for version autodetection rather than
+      runtime
+    - virtio_blk: fix the discard_granularity and discard_alignment queue limits
+    - nl80211: don't hold RTNL in color change request
+    - x86: Fix return value of __setup handlers
+    - irqchip/exiu: Fix acknowledgment of edge triggered interrupts
+    - irqchip/aspeed-i2c-ic: Fix irq_of_parse_and_map() return value
+    - irqchip/aspeed-scu-ic: Fix irq_of_parse_and_map() return value
+    - x86/mm: Cleanup the control_va_addr_alignment() __setup handler
+    - arm64: fix types in copy_highpage()
+    - regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
+    - drm/msm/dsi: fix address for second DSI PHY on SDM660
+    - drm/msm/dp: fix event thread stuck in wait_event after kthread_stop()
+    - drm/msm/mdp5: Return error code in mdp5_pipe_release when deadlock is
+      detected
+    - drm/msm/mdp5: Return error code in mdp5_mixer_release when deadlock is
+      detected
+    - drm/msm: return an error pointer in msm_gem_prime_get_sg_table()
+    - media: uvcvideo: Fix missing check to determine if element is found in list
+    - arm64: stackleak: fix current_top_of_stack()
+    - iomap: iomap_write_failed fix
+    - spi: spi-fsl-qspi: check return value after calling
+      platform_get_resource_byname()
+    - Revert "cpufreq: Fix possible race in cpufreq online error path"
+    - regulator: qcom_smd: Fix up PM8950 regulator configuration
+    - samples: bpf: Don't fail for a missing VMLINUX_BTF when VMLINUX_H is
+      provided
+    - perf/amd/ibs: Use interrupt regs ip for stack unwinding
+    - ath11k: Don't check arvif->is_started before sending management frames
+    - wilc1000: fix crash observed in AP mode with cfg80211_register_netdevice()
+    - HID: amd_sfh: Modify the bus name
+    - HID: amd_sfh: Modify the hid name
+    - ASoC: fsl: Use dev_err_probe() helper
+    - ASoC: fsl: Fix refcount leak in imx_sgtl5000_probe
+    - ASoC: imx-hdmi: Fix refcount leak in imx_hdmi_probe
+    - ASoC: mxs-saif: Fix refcount leak in mxs_saif_probe
+    - regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
+    - dma-direct: factor out a helper for DMA_ATTR_NO_KERNEL_MAPPING allocations
+    - dma-direct: don't fail on highmem CMA pages in dma_direct_alloc_pages
+    - ASoC: samsung: Use dev_err_probe() helper
+    - ASoC: samsung: Fix refcount leak in aries_audio_probe
+    - block: Fix the bio.bi_opf comment
+    - kselftest/cgroup: fix test_stress.sh to use OUTPUT dir
+    - scripts/faddr2line: Fix overlapping text section failures
+    - media: aspeed: Fix an error handling path in aspeed_video_probe()
+    - media: exynos4-is: Fix PM disable depth imbalance in fimc_is_probe
+    - mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
+    - mt76: do not attempt to reorder received 802.3 packets without agg session
+    - media: st-delta: Fix PM disable depth imbalance in delta_probe
+    - media: atmel: atmel-isc: Fix PM disable depth imbalance in atmel_isc_probe
+    - media: i2c: rdacm2x: properly set subdev entity function
+    - media: exynos4-is: Change clk_disable to clk_disable_unprepare
+    - media: pvrusb2: fix array-index-out-of-bounds in pvr2_i2c_core_init
+    - media: vsp1: Fix offset calculation for plane cropping
+    - media: atmel: atmel-sama5d2-isc: fix wrong mask in YUYV format check
+    - media: hantro: HEVC: Fix tile info buffer value computation
+    - Bluetooth: fix dangling sco_conn and use-after-free in sco_sock_timeout
+    - Bluetooth: use hdev lock in activate_scan for hci_is_adv_monitoring
+    - Bluetooth: use hdev lock for accept_list and reject_list in conn req
+    - nvme: set dma alignment to dword
+    - m68k: math-emu: Fix dependencies of math emulation support
+    - sctp: read sk->sk_bound_dev_if once in sctp_rcv()
+    - net: hinic: add missing destroy_workqueue in hinic_pf_to_mgmt_init
+    - ASoC: ti: j721e-evm: Fix refcount leak in j721e_soc_probe_*
+    - kselftest/arm64: bti: force static linking
+    - media: ov7670: remove ov7670_power_off from ov7670_remove
+    - media: i2c: ov5648: fix wrong pointer passed to IS_ERR() and PTR_ERR()
+    - media: staging: media: rkvdec: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - media: rkvdec: h264: Fix dpb_valid implementation
+    - media: rkvdec: h264: Fix bit depth wrap in pps packet
+    - regulator: scmi: Fix refcount leak in scmi_regulator_probe
+    - ext4: reject the 'commit' option on ext2 filesystems
+    - drm/msm/a6xx: Fix refcount leak in a6xx_gpu_init
+    - drm: msm: fix possible memory leak in mdp5_crtc_cursor_set()
+    - x86/sev: Annotate stack change in the #VC handler
+    - drm/msm: don't free the IRQ if it was not requested
+    - selftests/bpf: Add missed ima_setup.sh in Makefile
+    - drm/msm/dpu: handle pm_runtime_get_sync() errors in bind path
+    - drm/i915: Fix CFI violation with show_dynamic_id()
+    - thermal/drivers/bcm2711: Don't clamp temperature at zero
+    - thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe
+    - thermal/core: Fix memory leak in __thermal_cooling_device_register()
+    - thermal/drivers/imx_sc_thermal: Fix refcount leak in imx_sc_thermal_probe
+    - bfq: Relax waker detection for shared queues
+    - bfq: Allow current waker to defend against a tentative one
+    - ASoC: wm2000: fix missing clk_disable_unprepare() on error in
+      wm2000_anc_transition()
+    - PM: domains: Fix initialization of genpd's next_wakeup
+    - net: macb: Fix PTP one step sync support
+    - NFC: hci: fix sleep in atomic context bugs in nfc_hci_hcp_message_tx
+    - ASoC: max98090: Move check for invalid values before casting in
+      max98090_put_enab_tlv()
+    - net: stmmac: selftests: Use kcalloc() instead of kzalloc()
+    - net: stmmac: fix out-of-bounds access in a selftest
+    - hv_netvsc: Fix potential dereference of NULL pointer
+    - hwmon: (pmbus) Check PEC support before reading other registers
+    - rxrpc: Fix listen() setting the bar too high for the prealloc rings
+    - rxrpc: Don't try to resend the request if we're receiving the reply
+    - rxrpc: Fix overlapping ACK accounting
+    - rxrpc: Don't let ack.previousPacket regress
+    - rxrpc: Fix decision on when to generate an IDLE ACK
+    - net: huawei: hinic: Use devm_kcalloc() instead of devm_kzalloc()
+    - hinic: Avoid some over memory allocation
+    - net: dsa: restrict SMSC_LAN9303_I2C kconfig
+    - net/smc: postpone sk_refcnt increment in connect()
+    - dma-direct: factor out dma_set_{de,en}crypted helpers
+    - dma-direct: don't call dma_set_decrypted for remapped allocations
+    - dma-direct: always leak memory that can't be re-encrypted
+    - dma-direct: don't over-decrypt memory
+    - arm64: dts: rockchip: Move drive-impedance-ohm to emmc phy on rk3399
+    - arm64: dts: mt8192: Fix nor_flash status disable typo
+    - memory: samsung: exynos5422-dmc: Avoid some over memory allocation
+    - ARM: dts: BCM5301X: update CRU block description
+    - ARM: dts: BCM5301X: Update pin controller node name
+    - ARM: dts: suniv: F1C100: fix watchdog compatible
+    - soc: qcom: smp2p: Fix missing of_node_put() in smp2p_parse_ipc
+    - soc: qcom: smsm: Fix missing of_node_put() in smsm_parse_ipc
+    - PCI: cadence: Fix find_first_zero_bit() limit
+    - PCI: rockchip: Fix find_first_zero_bit() limit
+    - PCI: mediatek: Fix refcount leak in mtk_pcie_subsys_powerup()
+    - PCI: dwc: Fix setting error return on MSI DMA mapping failure
+    - ARM: dts: ci4x10: Adapt to changes in imx6qdl.dtsi regarding fec clocks
+    - soc: qcom: llcc: Add MODULE_DEVICE_TABLE()
+    - KVM: nVMX: Leave most VM-Exit info fields unmodified on failed VM-Entry
+    - KVM: nVMX: Clear IDT vectoring on nested VM-Exit for double/triple fault
+    - crypto: qat - set CIPHER capability for QAT GEN2
+    - crypto: qat - set COMPRESSION capability for QAT GEN2
+    - crypto: qat - set CIPHER capability for DH895XCC
+    - crypto: qat - set COMPRESSION capability for DH895XCC
+    - platform/chrome: cros_ec: fix error handling in cros_ec_register()
+    - ARM: dts: imx6dl-colibri: Fix I2C pinmuxing
+    - platform/chrome: Re-introduce cros_ec_cmd_xfer and use it for ioctls
+    - can: xilinx_can: mark bit timing constants as const
+    - ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
+    - ARM: dts: bcm2835-rpi-zero-w: Fix GPIO line name for Wifi/BT
+    - ARM: dts: bcm2837-rpi-cm3-io3: Fix GPIO line names for SMPS I2C
+    - ARM: dts: bcm2837-rpi-3-b-plus: Fix GPIO line name of power LED
+    - ARM: dts: bcm2835-rpi-b: Fix GPIO line names
+    - misc: ocxl: fix possible double free in ocxl_file_register_afu
+    - crypto: marvell/cesa - ECB does not IV
+    - gpiolib: of: Introduce hook for missing gpio-ranges
+    - pinctrl: bcm2835: implement hook for missing gpio-ranges
+    - arm: mediatek: select arch timer for mt7629
+    - pinctrl/rockchip: support deferring other gpio params
+    - pinctrl: mediatek: mt8195: enable driver on mtk platforms
+    - arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
+    - Drivers: hv: vmbus: Fix handling of messages with transaction ID of zero
+    - powerpc/fadump: fix PT_LOAD segment for boot memory area
+    - mfd: ipaq-micro: Fix error check return value of platform_get_irq()
+    - scsi: fcoe: Fix Wstringop-overflow warnings in fcoe_wwn_from_mac()
+    - soc: bcm: Check for NULL return of devm_kzalloc()
+    - arm64: dts: ti: k3-am64-mcu: remove incorrect UART base clock rates
+    - ASoC: sh: rz-ssi: Check return value of pm_runtime_resume_and_get()
+    - ASoC: sh: rz-ssi: Propagate error codes returned from
+      platform_get_irq_byname()
+    - ASoC: sh: rz-ssi: Release the DMA channels in rz_ssi_probe() error path
+    - firmware: arm_scmi: Fix list protocols enumeration in the base protocol
+    - nvdimm: Fix firmware activation deadlock scenarios
+    - nvdimm: Allow overwrite in the presence of disabled dimms
+    - pinctrl: mvebu: Fix irq_of_parse_and_map() return value
+    - drivers/base/node.c: fix compaction sysfs file leak
+    - dax: fix cache flush on PMD-mapped pages
+    - drivers/base/memory: fix an unlikely reference counting issue in
+      __add_memory_block()
+    - firmware: arm_ffa: Fix uuid parameter to ffa_partition_probe
+    - firmware: arm_ffa: Remove incorrect assignment of driver_data
+    - list: introduce list_is_head() helper and re-use it in list.h
+    - list: fix a data-race around ep->rdllist
+    - drm/msm/dpu: fix error check return value of irq_of_parse_and_map()
+    - powerpc/8xx: export 'cpm_setbrg' for modules
+    - pinctrl: renesas: r8a779a0: Fix GPIO function on I2C-capable pins
+    - pinctrl: renesas: core: Fix possible null-ptr-deref in
+      sh_pfc_map_resources()
+    - powerpc/idle: Fix return value of __setup() handler
+    - powerpc/4xx/cpm: Fix return value of __setup() handler
+    - RDMA/hns: Add the detection for CMDQ status in the device initialization
+      process
+    - arm64: dts: marvell: espressobin-ultra: fix SPI-NOR config
+    - arm64: dts: marvell: espressobin-ultra: enable front USB3 port
+    - ASoC: atmel-pdmic: Remove endianness flag on pdmic component
+    - ASoC: atmel-classd: Remove endianness flag on class d component
+    - proc: fix dentry/inode overinstantiating under /proc/${pid}/net
+    - ipc/mqueue: use get_tree_nodev() in mqueue_get_tree()
+    - PCI: imx6: Fix PERST# start-up sequence
+    - tty: fix deadlock caused by calling printk() under tty_port->lock
+    - crypto: sun8i-ss - rework handling of IV
+    - crypto: sun8i-ss - handle zero sized sg
+    - crypto: cryptd - Protect per-CPU resource by disabling BH.
+    - ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
+    - hugetlbfs: fix hugetlbfs_statfs() locking
+    - Input: sparcspkr - fix refcount leak in bbc_beep_probe
+    - PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
+    - PCI: microchip: Fix potential race in interrupt handling
+    - hwrng: omap3-rom - fix using wrong clk_disable() in
+      omap_rom_rng_runtime_resume()
+    - powerpc/64: Only WARN if __pa()/__va() called with bad addresses
+    - powerpc/perf: Fix the threshold compare group constraint for power10
+    - powerpc/perf: Fix the threshold compare group constraint for power9
+    - macintosh: via-pmu and via-cuda need RTC_LIB
+    - powerpc/xive: Add some error handling code to 'xive_spapr_init()'
+    - powerpc/xive: Fix refcount leak in xive_spapr_init
+    - powerpc/fsl_rio: Fix refcount leak in fsl_rio_setup
+    - mfd: davinci_voicecodec: Fix possible null-ptr-deref davinci_vc_probe()
+    - nfsd: destroy percpu stats counters after reply cache shutdown
+    - mailbox: forward the hrtimer if not queued and under a lock
+    - RDMA/hfi1: Prevent use of lock before it is initialized
+    - KVM: LAPIC: Drop pending LAPIC timer injection when canceling the timer
+    - Input: stmfts - do not leave device disabled in stmfts_input_open
+    - OPP: call of_node_put() on error path in _bandwidth_supported()
+    - f2fs: support fault injection for dquot_initialize()
+    - f2fs: fix to do sanity check on inline_dots inode
+    - f2fs: fix dereference of stale list iterator after loop body
+    - iommu/amd: Enable swiotlb in all cases
+    - iommu/mediatek: Fix 2 HW sharing pgtable issue
+    - iommu/mediatek: Add list_del in mtk_iommu_remove
+    - iommu/mediatek: Remove clk_disable in mtk_iommu_remove
+    - iommu/mediatek: Add mutex for m4u_group and m4u_dom in data
+    - i2c: at91: use dma safe buffers
+    - cpufreq: mediatek: Use module_init and add module_exit
+    - cpufreq: mediatek: Unregister platform device on exit
+    - iommu/arm-smmu-v3-sva: Fix mm use-after-free
+    - MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
+    - iommu/mediatek: Fix NULL pointer dereference when printing dev_name
+    - i2c: at91: Initialize dma_buf in at91_twi_xfer()
+    - dmaengine: idxd: Fix the error handling path in idxd_cdev_register()
+    - NFS: Do not report EINTR/ERESTARTSYS as mapping errors
+    - NFS: fsync() should report filesystem errors over EINTR/ERESTARTSYS
+    - NFS: Don't report ENOSPC write errors twice
+    - NFS: Do not report flush errors in nfs_write_end()
+    - NFS: Don't report errors from nfs_pageio_complete() more than once
+    - NFSv4/pNFS: Do not fail I/O when we fail to allocate the pNFS layout
+    - NFS: Further fixes to the writeback error handling
+    - video: fbdev: clcdfb: Fix refcount leak in clcdfb_of_vram_setup
+    - dmaengine: stm32-mdma: remove GISR1 register
+    - dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
+    - iommu/amd: Increase timeout waiting for GA log enablement
+    - i2c: npcm: Fix timeout calculation
+    - i2c: npcm: Correct register access width
+    - i2c: npcm: Handle spurious interrupts
+    - i2c: rcar: fix PM ref counts in probe error paths
+    - perf build: Fix btf__load_from_kernel_by_id() feature check
+    - perf c2c: Use stdio interface if slang is not supported
+    - perf jevents: Fix event syntax error caused by ExtSel
+    - video: fbdev: vesafb: Fix a use-after-free due early fb_info cleanup
+    - NFS: Always initialise fattr->label in nfs_fattr_alloc()
+    - NFS: Create a new nfs_alloc_fattr_with_label() function
+    - NFS: Convert GFP_NOFS to GFP_KERNEL
+    - NFSv4.1 mark qualified async operations as MOVEABLE tasks
+    - f2fs: fix to avoid f2fs_bug_on() in dec_valid_node_count()
+    - f2fs: fix to do sanity check on block address in f2fs_do_zero_range()
+    - f2fs: fix to clear dirty inode in f2fs_evict_inode()
+    - f2fs: fix deadloop in foreground GC
+    - f2fs: don't need inode lock for system hidden quota
+    - f2fs: fix to do sanity check on total_data_blocks
+    - f2fs: don't use casefolded comparison for "." and ".."
+    - f2fs: fix fallocate to use file_modified to update permissions consistently
+    - f2fs: fix to do sanity check for inline inode
+    - wifi: mac80211: fix use-after-free in chanctx code
+    - iwlwifi: mvm: fix assert 1F04 upon reconfig
+    - fs-writeback: writeback_sb_inodes：Recalculate 'wrote' according skipped
+      pages
+    - efi: Do not import certificates from UEFI Secure Boot for T2 Macs
+    - bfq: Avoid false marking of bic as stably merged
+    - bfq: Avoid merging queues with different parents
+    - bfq: Split shared queues on move between cgroups
+    - bfq: Update cgroup information before merging bio
+    - bfq: Drop pointless unlock-lock pair
+    - bfq: Remove pointless bfq_init_rq() calls
+    - bfq: Track whether bfq_group is still online
+    - bfq: Get rid of __bio_blkcg() usage
+    - bfq: Make sure bfqg for which we are queueing requests is online
+    - ext4: mark group as trimmed only if it was fully scanned
+    - ext4: fix use-after-free in ext4_rename_dir_prepare
+    - ext4: fix race condition between ext4_write and ext4_convert_inline_data
+    - ext4: fix warning in ext4_handle_inode_extension
+    - ext4: fix bug_on in ext4_writepages
+    - ext4: filter out EXT4_FC_REPLAY from on-disk superblock field s_state
+    - ext4: fix bug_on in __es_tree_search
+    - ext4: verify dir block before splitting it
+    - ext4: avoid cycles in directory h-tree
+    - ACPI: property: Release subnode properties with data nodes
+    - tty: goldfish: Introduce gf_ioread32()/gf_iowrite32()
+    - tracing: Fix potential double free in create_var_ref()
+    - tracing: Initialize integer variable to prevent garbage return value
+    - drm/amdgpu: add beige goby PCI ID
+    - PCI/PM: Fix bridge_d3_blacklist[] Elo i2 overwrite of Gigabyte X299
+    - PCI: qcom: Fix runtime PM imbalance on probe errors
+    - PCI: qcom: Fix unbalanced PHY init on probe errors
+    - staging: r8188eu: prevent ->Ssid overflow in rtw_wx_set_scan()
+    - mm, compaction: fast_find_migrateblock() should return pfn in the target
+      zone
+    - s390/perf: obtain sie_block from the right address
+    - s390/stp: clock_delta should be signed
+    - dlm: fix plock invalid read
+    - dlm: uninitialized variable on error in dlm_listen_for_all()
+    - dlm: fix missing lkb refcount handling
+    - ocfs2: dlmfs: fix error handling of user_dlm_destroy_lock
+    - scsi: dc395x: Fix a missing check on list iterator
+    - scsi: ufs: qcom: Add a readl() to make sure ref_clk gets enabled
+    - landlock: Add clang-format exceptions
+    - landlock: Format with clang-format
+    - selftests/landlock: Add clang-format exceptions
+    - selftests/landlock: Normalize array assignment
+    - selftests/landlock: Format with clang-format
+    - samples/landlock: Add clang-format exceptions
+    - samples/landlock: Format with clang-format
+    - landlock: Fix landlock_add_rule(2) documentation
+    - selftests/landlock: Make tests build with old libc
+    - selftests/landlock: Extend tests for minimal valid attribute size
+    - selftests/landlock: Add tests for unknown access rights
+    - selftests/landlock: Extend access right tests to directories
+    - selftests/landlock: Fully test file rename with "remove" access
+    - selftests/landlock: Add tests for O_PATH
+    - landlock: Change landlock_add_rule(2) argument check ordering
+    - landlock: Change landlock_restrict_self(2) check ordering
+    - selftests/landlock: Test landlock_create_ruleset(2) argument check ordering
+    - landlock: Define access_mask_t to enforce a consistent access mask size
+    - landlock: Reduce the maximum number of layers to 16
+    - landlock: Create find_rule() from unmask_layers()
+    - landlock: Fix same-layer rule unions
+    - drm/amdgpu/cs: make commands with 0 chunks illegal behaviour.
+    - drm/nouveau/subdev/bus: Ratelimit logging for fault errors
+    - drm/etnaviv: check for reaped mapping in etnaviv_iommu_unmap_gem
+    - drm/nouveau/clk: Fix an incorrect NULL check on list iterator
+    - drm/nouveau/kms/nv50-: atom: fix an incorrect NULL check on list iterator
+    - drm/bridge: analogix_dp: Grab runtime PM reference for DP-AUX
+    - drm/i915/dsi: fix VBT send packet port selection for ICL+
+    - md: fix an incorrect NULL check in does_sb_need_changing
+    - md: fix an incorrect NULL check in md_reload_sb
+    - mtd: cfi_cmdset_0002: Move and rename
+      chip_check/chip_ready/chip_good_for_write
+    - mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
+    - media: coda: Fix reported H264 profile
+    - media: coda: Add more H264 levels for CODA960
+    - ima: remove the IMA_TEMPLATE Kconfig option
+    - [Config] updateconfigs for IMA_TEMPLATE
+    - Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug
+    - RDMA/hfi1: Fix potential integer multiplication overflow errors
+    - mmc: core: Allows to override the timeout value for ioctl() path
+    - csky: patch_text: Fixup last cpu should be master
+    - irqchip/armada-370-xp: Do not touch Performance Counter Overflow on A375,
+      A38x, A39x
+    - irqchip: irq-xtensa-mx: fix initial IRQ affinity
+    - thermal: devfreq_cooling: use local ops instead of global ops
+    - cfg80211: declare MODULE_FIRMWARE for regulatory.db
+    - mac80211: upgrade passive scan to active scan on DFS channels after beacon
+      rx
+    - um: Use asm-generic/dma-mapping.h
+    - um: chan_user: Fix winch_tramp() return value
+    - um: Fix out-of-bounds read in LDT setup
+    - kexec_file: drop weak attribute from arch_kexec_apply_relocations[_add]
+    - ftrace: Clean up hash direct_functions on register failures
+    - ksmbd: fix outstanding credits related bugs
+    - iommu/msm: Fix an incorrect NULL check on list iterator
+    - iommu/dma: Fix iova map result check bug
+    - Revert "mm/cma.c: remove redundant cma_mutex lock"
+    - mm/page_alloc: always attempt to allocate at least one page during bulk
+      allocation
+    - nodemask.h: fix compilation error with GCC12
+    - hugetlb: fix huge_pmd_unshare address update
+    - mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
+    - xtensa/simdisk: fix proc_read_simdisk()
+    - rtl818x: Prevent using not initialized queues
+    - ASoC: rt5514: Fix event generation for "DSP Voice Wake Up" control
+    - carl9170: tx: fix an incorrect use of list iterator
+    - stm: ltdc: fix two incorrect NULL checks on list iterator
+    - bcache: remove incremental dirty sector counting for
+      bch_sectors_dirty_init()
+    - bcache: avoid journal no-space deadlock by reserving 1 journal bucket
+    - serial: pch: don't overwrite xmit->buf[0] by x_char
+    - tilcdc: tilcdc_external: fix an incorrect NULL check on list iterator
+    - gma500: fix an incorrect NULL check on list iterator
+    - arm64: dts: qcom: ipq8074: fix the sleep clock frequency
+    - arm64: tegra: Add missing DFLL reset on Tegra210
+    - clk: tegra: Add missing reset deassertion
+    - phy: qcom-qmp: fix struct clk leak on probe errors
+    - ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
+    - ARM: pxa: maybe fix gpio lookup tables
+    - SMB3: EBADF/EIO errors in rename/open caused by race condition in
+      smb2_compound_op
+    - docs/conf.py: Cope with removal of language=None in Sphinx 5.0.0
+    - dt-bindings: gpio: altera: correct interrupt-cells
+    - vdpasim: allow to enable a vq repeatedly
+    - blk-iolatency: Fix inflight count imbalances and IO hangs on offline
+    - coresight: core: Fix coresight device probe failure issue
+    - phy: qcom-qmp: fix reset-controller leak on probe errors
+    - net: ipa: fix page free in ipa_endpoint_trans_release()
+    - net: ipa: fix page free in ipa_endpoint_replenish_one()
+    - kseltest/cgroup: Make test_stress.sh work if run interactively
+    - list: test: Add a test for list_is_head()
+    - staging: r8188eu: delete rtw_wx_read/write32()
+    - RDMA/hns: Remove the num_cqc_timer variable
+    - RDMA/rxe: Generate a completion for unsupported/invalid opcode
+    - MIPS: IP27: Remove incorrect `cpu_has_fpu' override
+    - MIPS: IP30: Remove incorrect `cpu_has_fpu' override
+    - ext4: only allow test_dummy_encryption when supported
+    - interconnect: qcom: sc7180: Drop IP0 interconnects
+    - interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate
+    - fs: add two trivial lookup helpers
+    - exportfs: support idmapped mounts
+    - fs/ntfs3: Fix invalid free in log_replay
+    - md: Don't set mddev private to NULL in raid0 pers->free
+    - md: fix double free of io_acct_set bioset
+    - md: bcache: check the return value of kzalloc() in detached_dev_do_request()
+    - pinctrl/rockchip: support setting input-enable param
+    - block: fix bio_clone_blkg_association() to associate with proper blkcg_gq
+    - Linux 5.15.46
+
+  * [SRU] bcache deadlock during read IO in writeback mode (LP: #1980925) //
+    Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - bcache: improve multithreaded bch_btree_check()
+    - bcache: improve multithreaded bch_sectors_dirty_init()
+
+  * Jammy update: v5.15.45 upstream stable release (LP: #1981862)
+    - ALSA: usb-audio: Don't get sample rate for MCT Trigger 5 USB-to-HDMI
+    - pinctrl: sunxi: fix f1c100s uart2 function
+    - KVM: arm64: Don't hypercall before EL2 init
+    - percpu_ref_init(): clean ->percpu_count_ref on failure
+    - net: af_key: check encryption module availability consistency
+    - nfc: pn533: Fix buggy cleanup order
+    - net: ftgmac100: Disable hardware checksum on AST2600
+    - i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging
+    - drivers: i2c: thunderx: Allow driver to work with ACPI defined TWSI
+      controllers
+    - i2c: ismt: prevent memory corruption in ismt_access()
+    - assoc_array: Fix BUG_ON during garbage collect
+    - pipe: make poll_usage boolean and annotate its access
+    - pipe: Fix missing lock in pipe_resize_ring()
+    - net: ipa: compute proper aggregation limit
+    - drm/i915: Fix -Wstringop-overflow warning in call to intel_read_wm_latency()
+    - exfat: check if cluster num is valid
+    - lib/crypto: add prompts back to crypto libraries
+    - crypto: drbg - prepare for more fine-grained tracking of seeding state
+    - crypto: drbg - track whether DRBG was seeded with !rng_is_initialized()
+    - crypto: drbg - move dynamic ->reseed_threshold adjustments to __drbg_seed()
+    - crypto: drbg - make reseeding from get_random_bytes() synchronous
+    - netfilter: nf_tables: hold mutex on netns pre_exit path
+    - netfilter: nf_tables: double hook unregistration in netns path
+    - netfilter: conntrack: re-fetch conntrack after insertion
+    - KVM: PPC: Book3S HV: fix incorrect NULL check on list iterator
+    - x86/kvm: Alloc dummy async #PF token outside of raw spinlock
+    - x86, kvm: use correct GFP flags for preemption disabled
+    - KVM: x86: avoid calling x86 emulator without a decoded instruction
+    - KVM: x86: Drop WARNs that assert a triple fault never "escapes" from L2
+    - KVM: SVM: Use kzalloc for sev ioctl interfaces to prevent kernel data leak
+    - crypto: caam - fix i.MX6SX entropy delay value
+    - crypto: ecrdsa - Fix incorrect use of vli_cmp
+    - zsmalloc: fix races between asynchronous zspage free and page migration
+    - ALSA: usb-audio: Workaround for clock setup on TEAC devices
+    - ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
+    - ALSA: usb-audio: Configure sync endpoints before data
+    - Bluetooth: hci_qca: Use del_timer_sync() before freeing
+    - ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
+    - dm integrity: fix error code in dm_integrity_ctr()
+    - dm crypt: make printing of the key constant-time
+    - dm stats: add cond_resched when looping over entries
+    - dm verity: set DM_TARGET_IMMUTABLE feature flag
+    - raid5: introduce MD_BROKEN
+    - fs/ntfs3: validate BOOT sectors_per_clusters
+    - HID: multitouch: Add support for Google Whiskers Touchpad
+    - HID: multitouch: add quirks to enable Lenovo X12 trackpoint
+    - x86/sgx: Disconnect backing page references from dirty status
+    - x86/sgx: Mark PCMD page as dirty when modifying contents
+    - x86/sgx: Obtain backing storage page with enclave mutex held
+    - x86/sgx: Fix race between reclaimer and page fault handler
+    - x86/sgx: Ensure no data in PCMD page after truncate
+    - media: i2c: imx412: Fix reset GPIO polarity
+    - media: i2c: imx412: Fix power_off ordering
+    - tpm: Fix buffer access in tpm2_get_tpm_pt()
+    - tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()
+    - docs: submitting-patches: Fix crossref to 'The canonical patch format'
+    - NFS: Memory allocation failures are not server fatal errors
+    - NFSD: Fix possible sleep during nfsd4_release_lockowner()
+    - bpf: Fix potential array overflow in bpf_trampoline_get_progs()
+    - bpf: Enlarge offset check value to INT_MAX in bpf_skb_{load,store}_bytes
+    - bpf: Fix excessive memory allocation in stack_map_alloc()
+    - bpf: Reject writes for PTR_TO_MAP_KEY in check_helper_mem_access
+    - bpf: Check PTR_TO_MEM | MEM_RDONLY in check_helper_mem_access
+    - ALSA: usb-audio: Optimize TEAC clock quirk
+    - Linux 5.15.45
+
+  * Jammy update: v5.15.44 upstream stable release (LP: #1981649)
+    - Revert "UBUNTU: SAUCE: random: Make getrandom() ready earlier"
+    - ice: fix crash at allocation failure
+    - ACPI: sysfs: Fix BERT error region memory mapping
+    - MAINTAINERS: co-maintain random.c
+    - MAINTAINERS: add git tree for random.c
+    - lib/crypto: blake2s: include as built-in
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - lib/crypto: blake2s: move hmac construction into wireguard
+    - lib/crypto: sha1: re-roll loops to reduce code size
+    - lib/crypto: blake2s: avoid indirect calls to compression function for Clang
+      CFI
+    - random: document add_hwgenerator_randomness() with other input functions
+    - random: remove unused irq_flags argument from add_interrupt_randomness()
+    - random: use BLAKE2s instead of SHA1 in extraction
+    - random: do not sign extend bytes for rotation when mixing
+    - random: do not re-init if crng_reseed completes before primary init
+    - random: mix bootloader randomness into pool
+    - random: harmonize "crng init done" messages
+    - random: use IS_ENABLED(CONFIG_NUMA) instead of ifdefs
+    - random: early initialization of ChaCha constants
+    - random: avoid superfluous call to RDRAND in CRNG extraction
+    - random: don't reset crng_init_cnt on urandom_read()
+    - random: fix typo in comments
+    - random: cleanup poolinfo abstraction
+    - random: cleanup integer types
+    - random: remove incomplete last_data logic
+    - random: remove unused extract_entropy() reserved argument
+    - random: rather than entropy_store abstraction, use global
+    - random: remove unused OUTPUT_POOL constants
+    - random: de-duplicate INPUT_POOL constants
+    - random: prepend remaining pool constants with POOL_
+    - random: cleanup fractional entropy shift constants
+    - random: access input_pool_data directly rather than through pointer
+    - random: selectively clang-format where it makes sense
+    - random: simplify arithmetic function flow in account()
+    - random: continually use hwgenerator randomness
+    - random: access primary_pool directly rather than through pointer
+    - random: only call crng_finalize_init() for primary_crng
+    - random: use computational hash for entropy extraction
+    - random: simplify entropy debiting
+    - random: use linear min-entropy accumulation crediting
+    - random: always wake up entropy writers after extraction
+    - random: make credit_entropy_bits() always safe
+    - random: remove use_input_pool parameter from crng_reseed()
+    - random: remove batched entropy locking
+    - random: fix locking in crng_fast_load()
+    - random: use RDSEED instead of RDRAND in entropy extraction
+    - random: get rid of secondary crngs
+    - random: inline leaves of rand_initialize()
+    - random: ensure early RDSEED goes through mixer on init
+    - random: do not xor RDRAND when writing into /dev/random
+    - random: absorb fast pool into input pool after fast load
+    - random: use simpler fast key erasure flow on per-cpu keys
+    - random: use hash function for crng_slow_load()
+    - random: make more consistent use of integer types
+    - random: remove outdated INT_MAX >> 6 check in urandom_read()
+    - random: zero buffer after reading entropy from userspace
+    - random: fix locking for crng_init in crng_reseed()
+    - random: tie batched entropy generation to base_crng generation
+    - random: remove ifdef'd out interrupt bench
+    - random: remove unused tracepoints
+    - random: add proper SPDX header
+    - random: deobfuscate irq u32/u64 contributions
+    - random: introduce drain_entropy() helper to declutter crng_reseed()
+    - random: remove useless header comment
+    - random: remove whitespace and reorder includes
+    - random: group initialization wait functions
+    - random: group crng functions
+    - random: group entropy extraction functions
+    - random: group entropy collection functions
+    - random: group userspace read/write functions
+    - random: group sysctl functions
+    - random: rewrite header introductory comment
+    - random: defer fast pool mixing to worker
+    - random: do not take pool spinlock at boot
+    - random: unify early init crng load accounting
+    - random: check for crng_init == 0 in add_device_randomness()
+    - random: pull add_hwgenerator_randomness() declaration into random.h
+    - random: clear fast pool, crng, and batches in cpuhp bring up
+    - random: round-robin registers as ulong, not u32
+    - random: only wake up writers after zap if threshold was passed
+    - random: cleanup UUID handling
+    - random: unify cycles_t and jiffies usage and types
+    - random: do crng pre-init loading in worker rather than irq
+    - random: give sysctl_random_min_urandom_seed a more sensible value
+    - random: don't let 644 read-only sysctls be written to
+    - random: replace custom notifier chain with standard one
+    - random: use SipHash as interrupt entropy accumulator
+    - random: make consistent usage of crng_ready()
+    - random: reseed more often immediately after booting
+    - random: check for signal and try earlier when generating entropy
+    - random: skip fast_init if hwrng provides large chunk of entropy
+    - random: treat bootloader trust toggle the same way as cpu trust toggle
+    - random: re-add removed comment about get_random_{u32,u64} reseeding
+    - random: mix build-time latent entropy into pool at init
+    - random: do not split fast init input in add_hwgenerator_randomness()
+    - random: do not allow user to keep crng key around on stack
+    - random: check for signal_pending() outside of need_resched() check
+    - random: check for signals every PAGE_SIZE chunk of /dev/[u]random
+    - random: allow partial reads if later user copies fail
+    - random: make random_get_entropy() return an unsigned long
+    - random: document crng_fast_key_erasure() destination possibility
+    - random: fix sysctl documentation nits
+    - init: call time_init() before rand_initialize()
+    - ia64: define get_cycles macro for arch-override
+    - s390: define get_cycles macro for arch-override
+    - parisc: define get_cycles macro for arch-override
+    - alpha: define get_cycles macro for arch-override
+    - powerpc: define get_cycles macro for arch-override
+    - timekeeping: Add raw clock fallback for random_get_entropy()
+    - m68k: use fallback for random_get_entropy() instead of zero
+    - riscv: use fallback for random_get_entropy() instead of zero
+    - mips: use fallback for random_get_entropy() instead of just c0 random
+    - arm: use fallback for random_get_entropy() instead of zero
+    - nios2: use fallback for random_get_entropy() instead of zero
+    - x86/tsc: Use fallback for random_get_entropy() instead of zero
+    - um: use fallback for random_get_entropy() instead of zero
+    - sparc: use fallback for random_get_entropy() instead of zero
+    - xtensa: use fallback for random_get_entropy() instead of zero
+    - random: insist on random_get_entropy() existing in order to simplify
+    - random: do not use batches when !crng_ready()
+    - random: use first 128 bits of input as fast init
+    - random: do not pretend to handle premature next security model
+    - random: order timer entropy functions below interrupt functions
+    - random: do not use input pool from hard IRQs
+    - random: help compiler out with fast_mix() by using simpler arguments
+    - siphash: use one source of truth for siphash permutations
+    - random: use symbolic constants for crng_init states
+    - random: avoid initializing twice in credit race
+    - random: move initialization out of reseeding hot path
+    - random: remove ratelimiting for in-kernel unseeded randomness
+    - random: use proper jiffies comparison macro
+    - random: handle latent entropy and command line from random_init()
+    - random: credit architectural init the exact amount
+    - random: use static branch for crng_ready()
+    - random: remove extern from functions in header
+    - random: use proper return types on get_random_{int,long}_wait()
+    - random: make consistent use of buf and len
+    - random: move initialization functions out of hot pages
+    - random: move randomize_page() into mm where it belongs
+    - random: unify batched entropy implementations
+    - random: convert to using fops->read_iter()
+    - random: convert to using fops->write_iter()
+    - random: wire up fops->splice_{read,write}_iter()
+    - random: check for signals after page of pool writes
+    - ALSA: ctxfi: Add SB046x PCI ID
+    - Linux 5.15.44
+    - Revert "random: use static branch for crng_ready()"
+
+  * Jammy update: v5.15.43 upstream stable release (LP: #1981468)
+    - mptcp: Do TCP fallback on early DSS checksum failure
+    - Linux 5.15.43
+
+  * Jammy update: v5.15.42 upstream stable release (LP: #1981375)
+    - usb: gadget: fix race when gadget driver register via ioctl
+    - io_uring: arm poll for non-nowait files
+    - kernel/resource: Introduce request_mem_region_muxed()
+    - i2c: piix4: Replace hardcoded memory map size with a #define
+    - i2c: piix4: Move port I/O region request/release code into functions
+    - i2c: piix4: Move SMBus controller base address detect into function
+    - i2c: piix4: Move SMBus port selection into function
+    - i2c: piix4: Add EFCH MMIO support to region request and release
+    - i2c: piix4: Add EFCH MMIO support to SMBus base address detect
+    - i2c: piix4: Add EFCH MMIO support for SMBus port select
+    - i2c: piix4: Enable EFCH MMIO for Family 17h+
+    - Watchdog: sp5100_tco: Move timer initialization into function
+    - Watchdog: sp5100_tco: Refactor MMIO base address initialization
+    - Watchdog: sp5100_tco: Add initialization using EFCH MMIO
+    - Watchdog: sp5100_tco: Enable Family 17h+ CPUs
+    - mm/kfence: reset PG_slab and memcg_data before freeing __kfence_pool
+    - Revert "drm/i915/opregion: check port number bounds for SWSCI display power
+      state"
+    - rtc: fix use-after-free on device removal
+    - rtc: pcf2127: fix bug when reading alarm registers
+    - um: Cleanup syscall_handler_t definition/cast, fix warning
+    - Input: add bounds checking to input_set_capability()
+    - Input: stmfts - fix reference leak in stmfts_input_open
+    - nvme-pci: add quirks for Samsung X5 SSDs
+    - gfs2: Disable page faults during lockless buffered reads
+    - rtc: sun6i: Fix time overflow handling
+    - crypto: stm32 - fix reference leak in stm32_crc_remove
+    - crypto: x86/chacha20 - Avoid spurious jumps to other functions
+    - s390/traps: improve panic message for translation-specification exception
+    - s390/pci: improve zpci_dev reference counting
+    - vhost_vdpa: don't setup irq offloading when irq_num < 0
+    - tools/virtio: compile with -pthread
+    - nvmet: use a private workqueue instead of the system workqueue
+    - nvme-multipath: fix hang when disk goes live over reconnect
+    - rtc: mc146818-lib: Fix the AltCentury for AMD platforms
+    - fs: fix an infinite loop in iomap_fiemap
+    - MIPS: lantiq: check the return value of kzalloc()
+    - drbd: remove usage of list iterator variable after loop
+    - platform/chrome: cros_ec_debugfs: detach log reader wq from devm
+    - ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
+    - nilfs2: fix lockdep warnings in page operations for btree nodes
+    - nilfs2: fix lockdep warnings during disk space reclamation
+    - ALSA: usb-audio: Restore Rane SL-1 quirk
+    - ALSA: wavefront: Proper check of get_user() error
+    - ALSA: hda/realtek: Add quirk for TongFang devices with pop noise
+    - perf: Fix sys_perf_event_open() race against self
+    - selinux: fix bad cleanup on error in hashtab_duplicate()
+    - Fix double fget() in vhost_net_set_backend()
+    - PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
+    - Revert "can: m_can: pci: use custom bit timings for Elkhart Lake"
+    - KVM: x86/mmu: Update number of zapped pages even if page list is stable
+    - arm64: paravirt: Use RCU read locks to guard stolen_time
+    - arm64: mte: Ensure the cleared tags are visible before setting the PTE
+    - crypto: qcom-rng - fix infinite loop on requests not multiple of WORD_SZ
+    - libceph: fix potential use-after-free on linger ping and resends
+    - drm/i915/dmc: Add MMIO range restrictions
+    - drm/dp/mst: fix a possible memory leak in fetch_monitor_name()
+    - dma-buf: fix use of DMA_BUF_SET_NAME_{A,B} in userspace
+    - dma-buf: ensure unique directory name for dmabuf stats
+    - ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi
+    - pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl
+    - ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group
+    - ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
+    - ARM: dts: aspeed: Add secure boot controller node
+    - ARM: dts: aspeed: Add video engine to g6
+    - pinctrl: mediatek: mt8365: fix IES control pins
+    - ALSA: hda - fix unused Realtek function when PM is not enabled
+    - net: ipa: record proper RX transaction count
+    - net: macb: Increment rx bd head after allocating skb and buffer
+    - xfrm: rework default policy structure
+    - xfrm: fix "disable_policy" flag use when arriving from different devices
+    - net/sched: act_pedit: sanitize shift argument before usage
+    - netfilter: flowtable: fix excessive hw offload attempts after failure
+    - netfilter: nft_flow_offload: skip dst neigh lookup for ppp devices
+    - net: fix dev_fill_forward_path with pppoe + bridge
+    - netfilter: nft_flow_offload: fix offload with pppoe + vlan
+    - net: systemport: Fix an error handling path in bcm_sysport_probe()
+    - net: vmxnet3: fix possible use-after-free bugs in vmxnet3_rq_alloc_rx_buf()
+    - net: vmxnet3: fix possible NULL pointer dereference in vmxnet3_rq_cleanup()
+    - ice: fix crash when writing timestamp on RX rings
+    - ice: fix possible under reporting of ethtool Tx and Rx statistics
+    - ice: move ice_container_type onto ice_ring_container
+    - ice: Fix interrupt moderation settings getting cleared
+    - clk: at91: generated: consider range when calculating best rate
+    - net/qla3xxx: Fix a test in ql_reset_work()
+    - NFC: nci: fix sleep in atomic context bugs caused by nci_skb_alloc
+    - net/mlx5: DR, Fix missing flow_source when creating multi-destination FW
+      table
+    - net/mlx5e: Properly block LRO when XDP is enabled
+    - ARM: 9196/1: spectre-bhb: enable for Cortex-A15
+    - ARM: 9197/1: spectre-bhb: fix loop8 sequence for Thumb2
+    - mptcp: change the parameter of __mptcp_make_csum
+    - mptcp: reuse __mptcp_make_csum in validate_data_csum
+    - mptcp: fix checksum byte order
+    - igb: skip phy status check where unavailable
+    - netfilter: flowtable: fix TCP flow teardown
+    - netfilter: flowtable: pass flowtable to nf_flow_table_iterate()
+    - netfilter: flowtable: move dst_check to packet path
+    - net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
+    - riscv: dts: sifive: fu540-c000: align dma node name with dtschema
+    - scsi: ufs: core: Fix referencing invalid rsp field
+    - perf build: Fix check for btf__load_from_kernel_by_id() in libbpf
+    - gpio: gpio-vf610: do not touch other bits when set the target bit
+    - gpio: mvebu/pwm: Refuse requests with inverted polarity
+    - perf regs x86: Fix arch__intr_reg_mask() for the hybrid platform
+    - perf bench numa: Address compiler error on s390
+    - scsi: scsi_dh_alua: Properly handle the ALUA transitioning state
+    - scsi: qla2xxx: Fix missed DMA unmap for aborted commands
+    - mac80211: fix rx reordering with non explicit / psmp ack policy
+    - nl80211: validate S1G channel width
+    - selftests: add ping test with ping_group_range tuned
+    - fbdev: Prevent possible use-after-free in fb_release()
+    - net: fix wrong network header length
+    - nl80211: fix locking in nl80211_set_tx_bitrate_mask()
+    - ethernet: tulip: fix missing pci_disable_device() on error in
+      tulip_init_one()
+    - net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()
+    - net: atlantic: fix "frag[0] not initialized"
+    - net: atlantic: reduce scope of is_rsc_complete
+    - net: atlantic: add check for MAX_SKB_FRAGS
+    - net: atlantic: verify hw_head_ lies within TX buffer ring
+    - arm64: Enable repeat tlbi workaround on KRYO4XX gold CPUs
+    - Input: ili210x - fix reset timing
+    - dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group
+    - i2c: mt7621: fix missing clk_disable_unprepare() on error in mtk_i2c_probe()
+    - afs: Fix afs_getattr() to refetch file status if callback break occurred
+    - Linux 5.15.42
+
+  * CVE-2021-33061
+    - ixgbe: add the ability for the PF to disable VF link state
+    - ixgbe: add improvement for MDD response functionality
+    - ixgbevf: add disable link state
+
+  * Fix PSR flickers on Intel TGL laptops + AUO panel (LP: #1980087)
+    - SAUCE: drm/i915/display/psr: Fix flicker on TGL + AUO panel
+
+  * Fix audio on Zbook Studio G9  (LP: #1966010)
+    - ALSA: hda/realtek: Fix LED on Zbook Studio G9
+
+  * Support Cirrus audio codec configurations for Odin platform (LP: #1968861)
+    - ALSA: hda/cs8409: Support new Odin Variants
+    - ALSA: hda/cs8409: Add Speaker Playback Switch for Cyborg
+
+  * Fix beacon loss for rtl8821ce on certain platforms (LP: #1969771)
+    - rtw88: pci: 8821c: Disable 21ce completion timeout
+
+  * Suppress harmless warning from hp-wmi (LP: #1980307)
+    - platform/x86: hp-wmi: Ignore Sanitization Mode event
+
+  * Fix headset mic no sound on an HP desktop (LP: #1978925)
+    - ALSA: hda/realtek - ALC897 headset MIC no sound
+
+  * alsa/hda: mute led can't work on the lenovo machine with cs35l41 s-codec
+    (LP: #1978915)
+    - ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec
+
+  * Jammy update: v5.15.41 upstream stable release (LP: #1980278)
+    - batman-adv: Don't skb_split skbuffs with frag_list
+    - iwlwifi: iwl-dbg: Use del_timer_sync() before freeing
+    - hwmon: (tmp401) Add OF device ID table
+    - mac80211: Reset MBSSID parameters upon connection
+    - net: Fix features skip in for_each_netdev_feature()
+    - net: mscc: ocelot: fix last VCAP IS1/IS2 filter persisting in hardware when
+      deleted
+    - net: mscc: ocelot: fix VCAP IS2 filters matching on both lookups
+    - net: mscc: ocelot: restrict tc-trap actions to VCAP IS2 lookup 0
+    - net: mscc: ocelot: avoid corrupting hardware counters when moving VCAP
+      filters
+    - fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
+    - fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
+    - fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
+    - platform/surface: aggregator: Fix initialization order when compiling as
+      builtin module
+    - ice: Fix race during aux device (un)plugging
+    - ice: fix PTP stale Tx timestamps cleanup
+    - ipv4: drop dst in multicast routing path
+    - drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
+    - netlink: do not reset transport header in netlink_recvmsg()
+    - net: chelsio: cxgb4: Avoid potential negative array offset
+    - fbdev: efifb: Fix a use-after-free due early fb_info cleanup
+    - sfc: Use swap() instead of open coding it
+    - net: sfc: fix memory leak due to ptp channel
+    - mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protection
+    - nfs: fix broken handling of the softreval mount option
+    - ionic: fix missing pci_release_regions() on error in ionic_probe()
+    - dim: initialize all struct fields
+    - hwmon: (ltq-cputemp) restrict it to SOC_XWAY
+    - procfs: prevent unprivileged processes accessing fdinfo dir
+    - selftests: vm: Makefile: rename TARGETS to VMTARGETS
+    - arm64: vdso: fix makefile dependency on vdso.so
+    - virtio: fix virtio transitional ids
+    - s390/ctcm: fix variable dereferenced before check
+    - s390/ctcm: fix potential memory leak
+    - s390/lcs: fix variable dereferenced before check
+    - net/sched: act_pedit: really ensure the skb is writable
+    - net: ethernet: mediatek: ppe: fix wrong size passed to memset()
+    - net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral
+    - drm/vc4: hdmi: Fix build error for implicit function declaration
+    - net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
+    - net/smc: non blocking recvmsg() return -EAGAIN when no data and
+      signal_pending
+    - net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
+    - tls: Fix context leak on tls_device_down
+    - drm/vmwgfx: Fix fencing on SVGAv3
+    - gfs2: Fix filesystem block deallocation for short writes
+    - hwmon: (f71882fg) Fix negative temperature
+    - RDMA/irdma: Fix deadlock in irdma_cleanup_cm_core()
+    - iommu: arm-smmu: disable large page mappings for Nvidia arm-smmu
+    - ASoC: max98090: Reject invalid values in custom control put()
+    - ASoC: max98090: Generate notifications on changes for custom control
+    - ASoC: ops: Validate input values in snd_soc_put_volsw_range()
+    - s390: disable -Warray-bounds
+    - ASoC: SOF: Fix NULL pointer exception in sof_pci_probe callback
+    - net: emaclite: Don't advertise 1000BASE-T and do auto negotiation
+    - net: sfp: Add tx-fault workaround for Huawei MA5671A SFP ONT
+    - secure_seq: use the 64 bits of the siphash for port offset calculation
+    - tcp: use different parts of the port_offset for index and offset
+    - tcp: resalt the secret every 10 seconds
+    - tcp: add small random increments to the source port
+    - tcp: dynamically allocate the perturb table used by source ports
+    - tcp: increase source port perturb table to 2^16
+    - tcp: drop the hash_32() part from the index calculation
+    - interconnect: Restore sync state by ignoring ipa-virt in provider count
+    - firmware_loader: use kernel credentials when reading firmware
+    - KVM: PPC: Book3S PR: Enable MSR_DR for switch_mmu_context()
+    - usb: xhci-mtk: fix fs isoc's transfer error
+    - x86/mm: Fix marking of unused sub-pmd ranges
+    - tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
+    - tty: n_gsm: fix buffer over-read in gsm_dlci_data()
+    - tty: n_gsm: fix mux activation issues in gsm_config()
+    - usb: cdc-wdm: fix reading stuck on device close
+    - usb: typec: tcpci: Don't skip cleanup in .remove() on error
+    - usb: typec: tcpci_mt6360: Update for BMC PHY setting
+    - USB: serial: pl2303: add device id for HP LM930 Display
+    - USB: serial: qcserial: add support for Sierra Wireless EM7590
+    - USB: serial: option: add Fibocom L610 modem
+    - USB: serial: option: add Fibocom MA510 modem
+    - slimbus: qcom: Fix IRQ check in qcom_slim_probe
+    - fsl_lpuart: Don't enable interrupts too early
+    - serial: 8250_mtk: Fix UART_EFR register address
+    - serial: 8250_mtk: Fix register address for XON/XOFF character
+    - ceph: fix setting of xattrs on async created inodes
+    - Revert "mm/memory-failure.c: skip huge_zero_page in memory_failure()"
+    - mm/huge_memory: do not overkill when splitting huge_zero_page
+    - drm/vmwgfx: Disable command buffers on svga3 without gbobjects
+    - drm/nouveau/tegra: Stop using iommu_present()
+    - i40e: i40e_main: fix a missing check on list iterator
+    - net: atlantic: always deep reset on pm op, fixing up my null deref
+      regression
+    - net: phy: Fix race condition on link status change
+    - writeback: Avoid skipping inode writeback
+    - cgroup/cpuset: Remove cpus_allowed/mems_allowed setup in cpuset_init_smp()
+    - arm[64]/memremap: don't abuse pfn_valid() to ensure presence of linear map
+    - net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061
+    - net: phy: micrel: Pass .probe for KS8737
+    - SUNRPC: Ensure that the gssproxy client can start in a connected state
+    - drm/vmwgfx: Initialize drm_mode_fb_cmd2
+    - dma-buf: call dma_buf_stats_setup after dmabuf is in valid list
+    - mm/hwpoison: use pr_err() instead of dump_page() in get_any_page()
+    - ping: fix address binding wrt vrf
+    - usb: gadget: uvc: rename function to be more consistent
+    - usb: gadget: uvc: allow for application to cleanly shutdown
+    - Linux 5.15.41
+
+  * Jammy update: v5.15.40 upstream stable release (LP: #1980277)
+    - tools arch: Update arch/x86/lib/mem{cpy,set}_64.S copies used in 'perf bench
+      mem memcpy'
+    - Bluetooth: Fix the creation of hdev->name
+    - udf: Avoid using stale lengthOfImpUse
+    - mm: fix missing cache flush for all tail pages of compound page
+    - mm: hugetlb: fix missing cache flush in copy_huge_page_from_user()
+    - mm: shmem: fix missing cache flush in shmem_mfill_atomic_pte()
+    - mm: userfaultfd: fix missing cache flush in mcopy_atomic_pte() and
+      __mcopy_atomic()
+    - mm/hwpoison: fix error page recovered but reported "not recovered"
+    - mm/mlock: fix potential imbalanced rlimit ucounts adjustment
+    - mm: fix invalid page pointer returned with FOLL_PIN gups
+    - Linux 5.15.40
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 10 Aug 2022 09:49:40 +0200
+
+linux (5.15.0-46.49) jammy; urgency=medium
+
+  * CVE-2022-2585
+    - SAUCE: posix-cpu-timers: Cleanup CPU timers before freeing them during exec
+
+  * CVE-2022-2586
+    - SAUCE: netfilter: nf_tables: do not allow SET_ID to refer to another table
+    - SAUCE: netfilter: nf_tables: do not allow CHAIN_ID to refer to another table
+    - SAUCE: netfilter: nf_tables: do not allow RULE_ID to refer to another chain
+
+  * CVE-2022-2588
+    - SAUCE: net_sched: cls_route: remove from list when handle is 0
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Thu, 04 Aug 2022 14:16:56 -0300
+
+linux (5.15.0-45.48) jammy; urgency=medium
+
+  * CVE-2022-29900 // CVE-2022-29901
+    - x86/lib/atomic64_386_32: Rename things
+    - x86: Prepare asm files for straight-line-speculation
+    - x86: Prepare inline-asm for straight-line-speculation
+    - x86/alternative: Relax text_poke_bp() constraint
+    - kbuild: move objtool_args back to scripts/Makefile.build
+    - x86: Add straight-line-speculation mitigation
+    - kvm/emulate: Fix SETcc emulation function offsets with SLS
+    - crypto: x86/poly1305 - Fixup SLS
+    - objtool: Add straight-line-speculation validation
+    - objtool: Fix SLS validation for kcov tail-call replacement
+    - objtool: Fix objtool regression on x32 systems
+    - objtool: Fix symbol creation
+    - objtool: Introduce CFI hash
+    - objtool: Default ignore INT3 for unreachable
+    - x86, kvm: use proper ASM macros for kvm_vcpu_is_preempted
+    - x86/traps: Use pt_regs directly in fixup_bad_iret()
+    - x86/entry: Switch the stack after error_entry() returns
+    - x86/entry: Move PUSH_AND_CLEAR_REGS out of error_entry()
+    - x86/entry: Don't call error_entry() for XENPV
+    - x86/entry: Remove skip_r11rcx
+    - x86/realmode: build with -D__DISABLE_EXPORTS
+    - x86/ibt,ftrace: Make function-graph play nice
+    - x86/kvm/vmx: Make noinstr clean
+    - x86/cpufeatures: Move RETPOLINE flags to word 11
+    - x86/retpoline: Cleanup some #ifdefery
+    - x86/retpoline: Swizzle retpoline thunk
+    - x86/retpoline: Use -mfunction-return
+    - x86: Undo return-thunk damage
+    - x86,objtool: Create .return_sites
+    - objtool: skip non-text sections when adding return-thunk sites
+    - x86,static_call: Use alternative RET encoding
+    - x86/ftrace: Use alternative RET encoding
+    - x86/bpf: Use alternative RET encoding
+    - x86/kvm: Fix SETcc emulation for return thunks
+    - x86/vsyscall_emu/64: Don't use RET in vsyscall emulation
+    - x86/sev: Avoid using __x86_return_thunk
+    - x86: Use return-thunk in asm code
+    - x86/entry: Avoid very early RET
+    - objtool: Treat .text.__x86.* as noinstr
+    - x86: Add magic AMD return-thunk
+    - x86/bugs: Report AMD retbleed vulnerability
+    - x86/bugs: Add AMD retbleed= boot parameter
+    - x86/bugs: Enable STIBP for JMP2RET
+    - x86/bugs: Keep a per-CPU IA32_SPEC_CTRL value
+    - x86/entry: Add kernel IBRS implementation
+    - x86/bugs: Optimize SPEC_CTRL MSR writes
+    - x86/speculation: Add spectre_v2=ibrs option to support Kernel IBRS
+    - x86/bugs: Split spectre_v2_select_mitigation() and
+      spectre_v2_user_select_mitigation()
+    - x86/bugs: Report Intel retbleed vulnerability
+    - intel_idle: Disable IBRS during long idle
+    - objtool: Update Retpoline validation
+    - x86/xen: Rename SYS* entry points
+    - x86/xen: Add UNTRAIN_RET
+    - x86/bugs: Add retbleed=ibpb
+    - x86/bugs: Do IBPB fallback check only once
+    - objtool: Add entry UNRET validation
+    - x86/cpu/amd: Add Spectral Chicken
+    - x86/speculation: Fix RSB filling with CONFIG_RETPOLINE=n
+    - x86/speculation: Fix firmware entry SPEC_CTRL handling
+    - x86/speculation: Fix SPEC_CTRL write on SMT state change
+    - x86/speculation: Use cached host SPEC_CTRL value for guest entry/exit
+    - x86/speculation: Remove x86_spec_ctrl_mask
+    - objtool: Re-add UNWIND_HINT_{SAVE_RESTORE}
+    - KVM: VMX: Flatten __vmx_vcpu_run()
+    - KVM: VMX: Convert launched argument to flags
+    - KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS
+    - KVM: VMX: Fix IBRS handling after vmexit
+    - x86/speculation: Fill RSB on vmexit for IBRS
+    - KVM: VMX: Prevent RSB underflow before vmenter
+    - x86/common: Stamp out the stepping madness
+    - x86/cpu/amd: Enumerate BTC_NO
+    - x86/retbleed: Add fine grained Kconfig knobs
+    - x86/bugs: Add Cannon lake to RETBleed affected CPU list
+    - x86/entry: Move PUSH_AND_CLEAR_REGS() back into error_entry
+    - x86/bugs: Do not enable IBPB-on-entry when IBPB is not supported
+    - x86/kexec: Disable RET on kexec
+    - x86/speculation: Disable RRSBA behavior
+    - [Config]: Enable speculation mitigations
+    - x86/static_call: Serialize __static_call_fixup() properly
+    - x86/asm/32: Fix ANNOTATE_UNRET_SAFE use on 32-bit
+    - x86/bugs: Mark retbleed_strings static
+    - x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
+    - x86/kvm: fix FASTOP_SIZE when return thunks are enabled
+    - x86/speculation: Use DECLARE_PER_CPU for x86_spec_ctrl_current
+    - KVM: emulate: do not adjust size of fastop and setcc subroutines
+    - x86/bugs: Remove apostrophe typo
+    - efi/x86: use naked RET on mixed mode call wrapper
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Tue, 19 Jul 2022 18:57:17 -0300
+
+linux (5.15.0-43.46) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-43.46 -proposed tracker (LP: #1981243)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2022.07.11)
+
+  * nbd: requests can become stuck when disconnecting from server with qemu-nbd
+    (LP: #1896350)
+    - nbd: don't handle response without a corresponding request message
+    - nbd: make sure request completion won't concurrent
+    - nbd: don't clear 'NBD_CMD_INFLIGHT' flag if request is not completed
+    - nbd: fix io hung while disconnecting device
+
+  * Ubuntu 22.04 and 20.04 DPC Fixes for Failure Cases of DownPort Containment
+    events (LP: #1965241)
+    - PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
+    - PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
+    - [Config] Enable config option CONFIG_PCIE_EDR
+
+  * [SRU] Ubuntu 22.04 Feature Request-Add support for a NVMe-oF-TCP CDC Client
+    - TP 8010 (LP: #1948626)
+    - nvme: add CNTRLTYPE definitions for 'identify controller'
+    - nvme: send uevent on connection up
+    - nvme: expose cntrltype and dctype through sysfs
+
+  * [UBUNTU 22.04] Kernel oops while removing device from cio_ignore list
+    (LP: #1980951)
+    - s390/cio: derive cdev information only for IO-subchannels
+
+  * Jammy Charmed OpenStack deployment fails over connectivity issues when using
+    converged OVS bridge for control and data planes (LP: #1978820)
+    - net/mlx5e: TC NIC mode, fix tc chains miss table
+
+  * Hairpin traffic does not work with centralized NAT gw (LP: #1967856)
+    - net: openvswitch: fix misuse of the cached connection on tuple changes
+
+  * alsa: asoc: amd: the internal mic can't be dedected on yellow carp machines
+    (LP: #1980700)
+    - ASoC: amd: Add driver data to acp6x machine driver
+    - ASoC: amd: Add support for enabling DMIC on acp6x via _DSD
+
+  * AMD ACP 6.x DMIC Supports (LP: #1949245)
+    - ASoC: amd: add Yellow Carp ACP6x IP register header
+    - ASoC: amd: add Yellow Carp ACP PCI driver
+    - ASoC: amd: add acp6x init/de-init functions
+    - ASoC: amd: add platform devices for acp6x pdm driver and dmic driver
+    - ASoC: amd: add acp6x pdm platform driver
+    - ASoC: amd: add acp6x irq handler
+    - ASoC: amd: add acp6x pdm driver dma ops
+    - ASoC: amd: add acp6x pci driver pm ops
+    - ASoC: amd: add acp6x pdm driver pm ops
+    - ASoC: amd: enable Yellow carp acp6x drivers build
+    - ASoC: amd: create platform device for acp6x machine driver
+    - ASoC: amd: add YC machine driver using dmic
+    - ASoC: amd: enable Yellow Carp platform machine driver build
+    - ASoC: amd: fix uninitialized variable in snd_acp6x_probe()
+    - [Config] Enable AMD ACP 6 DMIC Support
+
+  * [UBUNTU 20.04] Include patches to avoid self-detected stall with Secure
+    Execution (LP: #1979296)
+    - KVM: s390: pv: add macros for UVC CC values
+    - KVM: s390: pv: avoid stalls when making pages secure
+
+  * [22.04 FEAT] KVM: Attestation support for Secure Execution (crypto)
+    (LP: #1959973)
+    - drivers/s390/char: Add Ultravisor io device
+    - s390/uv_uapi: depend on CONFIG_S390
+    - [Config] CONFIG_S390_UV_UAPI=y for s390x
+
+  * CVE-2022-1679
+    - SAUCE: ath9k: fix use-after-free in ath9k_hif_usb_rx_cb
+
+  * CVE-2022-28893
+    - SUNRPC: Ensure we flush any closed sockets before xs_xprt_free()
+    - SUNRPC: Don't leak sockets in xs_local_connect()
+
+  * CVE-2022-34918
+    - netfilter: nf_tables: stricter validation of element data
+
+  * CVE-2022-1652
+    - floppy: use a statically allocated error counter
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Tue, 12 Jul 2022 10:51:03 +0200
+
+linux (5.15.0-41.44) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-41.44 -proposed tracker (LP: #1979448)
+
+  * Fix can't boot up after change to vmd  (LP: #1976587)
+    - PCI: vmd: Assign VMD IRQ domain before enumeration
+    - PCI: vmd: Revert 2565e5b69c44 ("PCI: vmd: Do not disable MSI-X remapping if
+      interrupt remapping is enabled by IOMMU.")
+
+  * [SRU][Jammy/OEM-5.17][PATCH 0/1] Fix calltrace in mac80211 (LP: #1978297)
+    - mac80211: fix struct ieee80211_tx_info size
+
+  * [SRU][Jammy][PATCH 0/1] Fix amd display corruption on s2idle resume
+    (LP: #1978244)
+    - drm/amd/display: Don't reinitialize DMCUB on s0ix resume
+
+  * pl2303 serial adapter not recognized (LP: #1967493)
+    - USB: serial: pl2303: fix type detection for odd device
+
+  * Remove SAUCE patches from test_vxlan_under_vrf.sh in net of
+    ubuntu_kernel_selftests (LP: #1975691)
+    - Revert "UBUNTU: SAUCE: selftests: net: Don't fail test_vxlan_under_vrf on
+      xfail"
+    - Revert "UBUNTU: SAUCE: selftests: net: Make test for VXLAN underlay in non-
+      default VRF an expected failure"
+
+  * Fix hp_wmi_read_int() reporting error (0x05) (LP: #1979051)
+    - platform/x86: hp-wmi: Fix hp_wmi_read_int() reporting error (0x05)
+
+  * Request to back port vmci patches to Ubuntu kernel (LP: #1978145)
+    - VMCI: dma dg: whitespace formatting change for vmci register defines
+    - VMCI: dma dg: add MMIO access to registers
+    - VMCI: dma dg: detect DMA datagram capability
+    - VMCI: dma dg: set OS page size
+    - VMCI: dma dg: register dummy IRQ handlers for DMA datagrams
+    - VMCI: dma dg: allocate send and receive buffers for DMA datagrams
+    - VMCI: dma dg: add support for DMA datagrams sends
+    - VMCI: dma dg: add support for DMA datagrams receive
+    - VMCI: Fix some error handling paths in vmci_guest_probe_device()
+    - VMCI: Release notification_bitmap in error path
+    - VMCI: Check exclusive_vectors when freeing interrupt 1
+    - VMCI: Add support for ARM64
+    - [Config] Update policies for VMWARE_VMCI and VMWARE_VMCI_VSOCKETS
+
+  * [UBUNTU 20.04] rcu stalls with many storage key guests (LP: #1975582)
+    - s390/gmap: voluntarily schedule during key setting
+    - s390/mm: use non-quiescing sske for KVM switch to keyed guest
+
+  * [SRU][OEM-5.14/OEM-5.17/Jammy][PATCH 0/1] Fix i915 calltrace on new ADL BIOS
+    (LP: #1976214)
+    - drm/i915: update new TMDS clock setting defined by VBT
+
+  * Revert PPC get_user workaround (LP: #1976248)
+    - powerpc: Export mmu_feature_keys[] as non-GPL
+
+  * Jammy update: v5.15.39 upstream stable release (LP: #1978240)
+    - MIPS: Fix CP0 counter erratum detection for R4k CPUs
+    - parisc: Merge model and model name into one line in /proc/cpuinfo
+    - ALSA: hda/realtek: Add quirk for Yoga Duet 7 13ITL6 speakers
+    - ALSA: fireworks: fix wrong return count shorter than expected by 4 bytes
+    - mmc: sdhci-msm: Reset GCC_SDCC_BCR register for SDHC
+    - mmc: sunxi-mmc: Fix DMA descriptors allocated above 32 bits
+    - mmc: core: Set HS clock speed before sending HS CMD13
+    - gpiolib: of: fix bounds check for 'gpio-reserved-ranges'
+    - x86/fpu: Prevent FPU state corruption
+    - KVM: x86/svm: Account for family 17h event renumberings in
+      amd_pmc_perf_hw_id
+    - iommu/vt-d: Calculate mask for non-aligned flushes
+    - iommu/arm-smmu-v3: Fix size calculation in arm_smmu_mm_invalidate_range()
+    - drm/amd/display: Avoid reading audio pattern past AUDIO_CHANNELS_COUNT
+    - drm/amdgpu: do not use passthrough mode in Xen dom0
+    - RISC-V: relocate DTB if it's outside memory region
+    - Revert "SUNRPC: attempt AF_LOCAL connect on setup"
+    - timekeeping: Mark NMI safe time accessors as notrace
+    - firewire: fix potential uaf in outbound_phy_packet_callback()
+    - firewire: remove check of list iterator against head past the loop body
+    - firewire: core: extend card->lock in fw_core_handle_bus_reset
+    - net: stmmac: disable Split Header (SPH) for Intel platforms
+    - genirq: Synchronize interrupt thread startup
+    - ASoC: da7219: Fix change notifications for tone generator frequency
+    - ASoC: wm8958: Fix change notifications for DSP controls
+    - ASoC: meson: Fix event generation for AUI ACODEC mux
+    - ASoC: meson: Fix event generation for G12A tohdmi mux
+    - ASoC: meson: Fix event generation for AUI CODEC mux
+    - s390/dasd: fix data corruption for ESE devices
+    - s390/dasd: prevent double format of tracks for ESE devices
+    - s390/dasd: Fix read for ESE with blksize < 4k
+    - s390/dasd: Fix read inconsistency for ESE DASD devices
+    - can: grcan: grcan_close(): fix deadlock
+    - can: isotp: remove re-binding of bound socket
+    - can: grcan: use ofdev->dev when allocating DMA memory
+    - can: grcan: grcan_probe(): fix broken system id check for errata workaround
+      needs
+    - can: grcan: only use the NAPI poll budget for RX
+    - nfc: replace improper check device_is_registered() in netlink related
+      functions
+    - nfc: nfcmrvl: main: reorder destructive operations in
+      nfcmrvl_nci_unregister_dev to avoid bugs
+    - NFC: netlink: fix sleep in atomic bug when firmware download timeout
+    - gpio: visconti: Fix fwnode of GPIO IRQ
+    - gpio: pca953x: fix irq_stat not updated when irq is disabled (irq_mask not
+      set)
+    - hwmon: (adt7470) Fix warning on module removal
+    - hwmon: (pmbus) disable PEC if not enabled
+    - ASoC: dmaengine: Restore NULL prepare_slave_config() callback
+    - ASoC: soc-ops: fix error handling
+    - iommu/vt-d: Drop stop marker messages
+    - iommu/dart: check return value after calling platform_get_resource()
+    - net/mlx5e: Fix trust state reset in reload
+    - net/mlx5e: Don't match double-vlan packets if cvlan is not set
+    - net/mlx5e: CT: Fix queued up restore put() executing after relevant ft
+      release
+    - net/mlx5e: Fix the calling of update_buffer_lossy() API
+    - net/mlx5: Avoid double clear or set of sync reset requested
+    - net/mlx5: Fix deadlock in sync reset flow
+    - selftests/seccomp: Don't call read() on TTY from background pgrp
+    - SUNRPC release the transport of a relocated task with an assigned transport
+    - RDMA/siw: Fix a condition race issue in MPA request processing
+    - RDMA/irdma: Flush iWARP QP if modified to ERR from RTR state
+    - RDMA/irdma: Reduce iWARP QP destroy time
+    - RDMA/irdma: Fix possible crash due to NULL netdev in notifier
+    - NFSv4: Don't invalidate inode attributes on delegation return
+    - net: ethernet: mediatek: add missing of_node_put() in mtk_sgmii_init()
+    - net: dsa: mt7530: add missing of_node_put() in mt7530_setup()
+    - net: stmmac: dwmac-sun8i: add missing of_node_put() in
+      sun8i_dwmac_register_mdio_mux()
+    - net: mdio: Fix ENOMEM return value in BCM6368 mux bus controller
+    - net: cpsw: add missing of_node_put() in cpsw_probe_dt()
+    - net: igmp: respect RCU rules in ip_mc_source() and ip_mc_msfilter()
+    - net: emaclite: Add error handling for of_address_to_resource()
+    - selftests/net: so_txtime: fix parsing of start time stamp on 32 bit systems
+    - selftests/net: so_txtime: usage(): fix documentation of default clock
+    - drm/msm/dp: remove fail safe mode related code
+    - btrfs: do not BUG_ON() on failure to update inode when setting xattr
+    - hinic: fix bug of wq out of bound access
+    - mld: respect RCU rules in ip6_mc_source() and ip6_mc_msfilter()
+    - rxrpc: Enable IPv6 checksums on transport socket
+    - selftests: mirror_gre_bridge_1q: Avoid changing PVID while interface is
+      operational
+    - bnxt_en: Fix possible bnxt_open() failure caused by wrong RFS flag
+    - bnxt_en: Fix unnecessary dropping of RX packets
+    - selftests: ocelot: tc_flower_chains: specify conform-exceed action for
+      policer
+    - smsc911x: allow using IRQ0
+    - btrfs: force v2 space cache usage for subpage mount
+    - btrfs: always log symlinks in full mode
+    - gpio: mvebu: drop pwm base assignment
+    - kvm: x86/cpuid: Only provide CPUID leaf 0xA if host has architectural PMU
+    - net/mlx5: Fix slab-out-of-bounds while reading resource dump menu
+    - net/mlx5e: Lag, Fix use-after-free in fib event handler
+    - net/mlx5e: Lag, Fix fib_info pointer assignment
+    - net/mlx5e: Lag, Don't skip fib events on current dst
+    - iommu/dart: Add missing module owner to ops structure
+    - kvm: selftests: do not use bitfields larger than 32-bits for PTEs
+    - KVM: selftests: Silence compiler warning in the kvm_page_table_test
+    - x86/kvm: Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
+    - KVM: x86: Do not change ICR on write to APIC_SELF_IPI
+    - KVM: x86/mmu: avoid NULL-pointer dereference on page freeing bugs
+    - KVM: LAPIC: Enable timer posted-interrupt only when mwait/hlt is advertised
+    - selftest/vm: verify mmap addr in mremap_test
+    - selftest/vm: verify remap destination address in mremap_test
+    - Revert "parisc: Mark sched_clock unstable only if clocks are not
+      syncronized"
+    - rcu: Fix callbacks processing time limit retaining cond_resched()
+    - rcu: Apply callbacks processing time limit only on softirq
+    - PCI: pci-bridge-emul: Add description for class_revision field
+    - PCI: pci-bridge-emul: Add definitions for missing capabilities registers
+    - PCI: aardvark: Add support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
+      registers on emulated bridge
+    - PCI: aardvark: Clear all MSIs at setup
+    - PCI: aardvark: Comment actions in driver remove method
+    - PCI: aardvark: Disable bus mastering when unbinding driver
+    - PCI: aardvark: Mask all interrupts when unbinding driver
+    - PCI: aardvark: Fix memory leak in driver unbind
+    - PCI: aardvark: Assert PERST# when unbinding driver
+    - PCI: aardvark: Disable link training when unbinding driver
+    - PCI: aardvark: Disable common PHY when unbinding driver
+    - PCI: aardvark: Replace custom PCIE_CORE_INT_* macros with PCI_INTERRUPT_*
+    - PCI: aardvark: Check return value of generic_handle_domain_irq() when
+      processing INTx IRQ
+    - PCI: aardvark: Make MSI irq_chip structures static driver structures
+    - PCI: aardvark: Make msi_domain_info structure a static driver structure
+    - PCI: aardvark: Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node)
+    - PCI: aardvark: Refactor unmasking summary MSI interrupt
+    - PCI: aardvark: Add support for masking MSI interrupts
+    - PCI: aardvark: Fix setting MSI address
+    - PCI: aardvark: Enable MSI-X support
+    - PCI: aardvark: Add support for ERR interrupt on emulated bridge
+    - PCI: aardvark: Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on
+      emulated bridge
+    - PCI: aardvark: Add support for PME interrupts
+    - PCI: aardvark: Fix support for PME requester on emulated bridge
+    - PCI: aardvark: Use separate INTA interrupt for emulated root bridge
+    - PCI: aardvark: Remove irq_mask_ack() callback for INTx interrupts
+    - PCI: aardvark: Don't mask irq when mapping
+    - PCI: aardvark: Drop __maybe_unused from advk_pcie_disable_phy()
+    - PCI: aardvark: Update comment about link going down after link-up
+    - Linux 5.15.39
+
+  * Jammy update: v5.15.38 upstream stable release (LP: #1978234)
+    - usb: mtu3: fix USB 3.0 dual-role-switch from device to host
+    - USB: quirks: add a Realtek card reader
+    - USB: quirks: add STRING quirk for VCOM device
+    - USB: serial: whiteheat: fix heap overflow in WHITEHEAT_GET_DTR_RTS
+    - USB: serial: cp210x: add PIDs for Kamstrup USB Meter Reader
+    - USB: serial: option: add support for Cinterion MV32-WA/MV32-WB
+    - USB: serial: option: add Telit 0x1057, 0x1058, 0x1075 compositions
+    - usb: xhci: tegra:Fix PM usage reference leak of
+      tegra_xusb_unpowergate_partitions
+    - xhci: Enable runtime PM on second Alderlake controller
+    - xhci: stop polling roothubs after shutdown
+    - xhci: increase usb U3 -> U0 link resume timeout from 100ms to 500ms
+    - iio: dac: ad5592r: Fix the missing return value.
+    - iio: dac: ad5446: Fix read_raw not returning set value
+    - iio: magnetometer: ak8975: Fix the error handling in ak8975_power_on()
+    - iio: imu: inv_icm42600: Fix I2C init possible nack
+    - usb: misc: fix improper handling of refcount in uss720_probe()
+    - usb: core: Don't hold the device lock while sleeping in do_proc_control()
+    - usb: typec: ucsi: Fix reuse of completion structure
+    - usb: typec: ucsi: Fix role swapping
+    - usb: gadget: uvc: Fix crash when encoding data for usb request
+    - usb: gadget: configfs: clear deactivation flag in
+      configfs_composite_unbind()
+    - usb: dwc3: Try usb-role-switch first in dwc3_drd_init
+    - usb: dwc3: core: Fix tx/rx threshold settings
+    - usb: dwc3: core: Only handle soft-reset in DCTL
+    - usb: dwc3: gadget: Return proper request status
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-P
+    - usb: cdns3: Fix issue for clear halt endpoint
+    - usb: phy: generic: Get the vbus supply
+    - serial: imx: fix overrun interrupts in DMA mode
+    - serial: amba-pl011: do not time out prematurely when draining tx fifo
+    - serial: 8250: Also set sticky MCR bits in console restoration
+    - serial: 8250: Correct the clock for EndRun PTP/1588 PCIe device
+    - arch_topology: Do not set llc_sibling if llc_id is invalid
+    - ceph: fix possible NULL pointer dereference for req->r_session
+    - bus: mhi: host: pci_generic: Add missing poweroff() PM callback
+    - bus: mhi: host: pci_generic: Flush recovery worker during freeze
+    - arm64: dts: imx8mm-venice: fix spi2 pin configuration
+    - pinctrl: samsung: fix missing GPIOLIB on ARM64 Exynos config
+    - hex2bin: make the function hex_to_bin constant-time
+    - hex2bin: fix access beyond string end
+    - riscv: patch_text: Fixup last cpu should be master
+    - x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
+    - iocost: don't reset the inuse weight of under-weighted debtors
+    - virtio_net: fix wrong buf address calculation when using xdp
+    - cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
+    - cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
+    - video: fbdev: udlfb: properly check endpoint type
+    - arm64: dts: meson: remove CPU opps below 1GHz for G12B boards
+    - arm64: dts: meson: remove CPU opps below 1GHz for SM1 boards
+    - iio:imu:bmi160: disable regulator in error path
+    - mtd: rawnand: fix ecc parameters for mt7622
+    - xsk: Fix l2fwd for copy mode + busy poll combo
+    - arm64: dts: imx8qm: Correct SCU clock controller's compatible property
+    - USB: Fix xhci event ring dequeue pointer ERDP update issue
+    - ARM: dts: imx6qdl-apalis: Fix sgtl5000 detection issue
+    - arm64: dts: imx8mn: Fix SAI nodes
+    - arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO pin labeling for CON1
+    - phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe
+    - phy: samsung: exynos5250-sata: fix missing device put in probe error paths
+    - ARM: OMAP2+: Fix refcount leak in omap_gic_of_init
+    - bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific
+    - ARM: dts: dra7: Fix suspend warning for vpe powerdomain
+    - phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks
+    - ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
+    - ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
+    - ARM: dts: at91: fix pinctrl phandles
+    - phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe
+    - phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe
+    - interconnect: qcom: sdx55: Drop IP0 interconnects
+    - ARM: dts: Fix mmc order for omap3-gta04
+    - ARM: dts: am3517-evm: Fix misc pinmuxing
+    - ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
+    - ipvs: correctly print the memory size of ip_vs_conn_tab
+    - phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe()
+    - pinctrl: mediatek: moore: Fix build error
+    - mtd: rawnand: Fix return value check of wait_for_completion_timeout
+    - mtd: fix 'part' field data corruption in mtd_info
+    - pinctrl: stm32: Do not call stm32_gpio_get() for edge triggered IRQs in EOI
+    - memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
+    - net: dsa: Add missing of_node_put() in dsa_port_link_register_of
+    - netfilter: nft_set_rbtree: overlap detection with element re-addition after
+      deletion
+    - bpf, lwt: Fix crash when using bpf_skb_set_tunnel_key() from bpf_xmit lwt
+      hook
+    - pinctrl: rockchip: fix RK3308 pinmux bits
+    - tcp: md5: incorrect tcp_header_len for incoming connections
+    - pinctrl: stm32: Keep pinctrl block clock enabled when LEVEL IRQ requested
+    - tcp: ensure to use the most recently sent skb when filling the rate sample
+    - wireguard: device: check for metadata_dst with skb_valid_dst()
+    - sctp: check asoc strreset_chunk in sctp_generate_reconf_event
+    - ARM: dts: imx6ull-colibri: fix vqmmc regulator
+    - arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
+    - pinctrl: pistachio: fix use of irq_of_parse_and_map()
+    - cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
+    - net: hns3: clear inited state and stop client after failed to register
+      netdev
+    - net: hns3: modify the return code of hclge_get_ring_chain_from_mbx
+    - net: hns3: add validity check for message data length
+    - net: hns3: add return value for mailbox handling in PF
+    - net/smc: sync err code when tcp connection was refused
+    - ip_gre: Make o_seqno start from 0 in native mode
+    - ip6_gre: Make o_seqno start from 0 in native mode
+    - ip_gre, ip6_gre: Fix race condition on o_seqno in collect_md mode
+    - tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT
+    - tcp: make sure treq->af_specific is initialized
+    - bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
+    - clk: sunxi: sun9i-mmc: check return value after calling
+      platform_get_resource()
+    - cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
+    - net: bcmgenet: hide status block before TX timestamping
+    - net: phy: marvell10g: fix return value on error
+    - net: dsa: mv88e6xxx: Fix port_hidden_wait to account for port_base_addr
+    - drm/sun4i: Remove obsolete references to PHYS_OFFSET
+    - net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK
+    - io_uring: check reserved fields for send/sendmsg
+    - io_uring: check reserved fields for recv/recvmsg
+    - netfilter: conntrack: fix udp offload timeout sysctl
+    - drm/amdkfd: Fix GWS queue count
+    - drm/amd/display: Fix memory leak in dcn21_clock_source_create
+    - tls: Skip tls_append_frag on zero copy size
+    - bnx2x: fix napi API usage sequence
+    - net: fec: add missing of_node_put() in fec_enet_init_stop_mode()
+    - gfs2: Prevent endless loops in gfs2_file_buffered_write
+    - gfs2: Minor retry logic cleanup
+    - gfs2: Make sure not to return short direct writes
+    - gfs2: No short reads or writes upon glock contention
+    - perf arm-spe: Fix addresses of synthesized SPE events
+    - ixgbe: ensure IPsec VF<->PF compatibility
+    - Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"
+    - tcp: fix F-RTO may not work correctly when receiving DSACK
+    - ASoC: Intel: soc-acpi: correct device endpoints for max98373
+    - ASoC: wm8731: Disable the regulator when probing fails
+    - ext4: fix bug_on in start_this_handle during umount filesystem
+    - arch: xtensa: platforms: Fix deadlock in rs_close()
+    - ksmbd: increment reference count of parent fp
+    - ksmbd: set fixed sector size to FS_SECTOR_SIZE_INFORMATION
+    - bonding: do not discard lowest hash bit for non layer3+4 hashing
+    - x86: __memcpy_flushcache: fix wrong alignment if size > 2^32
+    - cifs: destage any unwritten data to the server before calling
+      copychunk_write
+    - drivers: net: hippi: Fix deadlock in rr_close()
+    - powerpc/perf: Fix 32bit compile
+    - selftest/vm: verify mmap addr in mremap_test
+    - selftest/vm: verify remap destination address in mremap_test
+    - Revert "ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40"
+    - zonefs: Fix management of open zones
+    - zonefs: Clear inode information flags on inode creation
+    - kasan: prevent cpu_quarantine corruption when CPU offline and cache shrink
+      occur at same time
+    - mtd: rawnand: qcom: fix memory corruption that causes panic
+    - netfilter: Update ip6_route_me_harder to consider L3 domain
+    - drm/i915: Check EDID for HDR static metadata when choosing blc
+    - drm/i915: Fix SEL_FETCH_PLANE_*(PIPE_B+) register addresses
+    - net: ethernet: stmmac: fix write to sgmii_adapter_base
+    - ACPI: processor: idle: Avoid falling back to C3 type C-states
+    - thermal: int340x: Fix attr.show callback prototype
+    - btrfs: fix leaked plug after failure syncing log on zoned filesystems
+    - ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
+    - ARM: dts: imx8mm-venice-gw{71xx,72xx,73xx}: fix OTG controller OC mode
+    - x86/cpu: Load microcode during restore_processor_state()
+    - perf symbol: Pass is_kallsyms to symbols__fixup_end()
+    - perf symbol: Update symbols__fixup_end()
+    - tty: n_gsm: fix restart handling via CLD command
+    - tty: n_gsm: fix decoupled mux resource
+    - tty: n_gsm: fix mux cleanup after unregister tty device
+    - tty: n_gsm: fix wrong signal octet encoding in convergence layer type 2
+    - tty: n_gsm: fix malformed counter for out of frame data
+    - netfilter: nft_socket: only do sk lookups when indev is available
+    - tty: n_gsm: fix insufficient txframe size
+    - tty: n_gsm: fix wrong DLCI release order
+    - tty: n_gsm: fix missing explicit ldisc flush
+    - tty: n_gsm: fix wrong command retry handling
+    - tty: n_gsm: fix wrong command frame length field encoding
+    - tty: n_gsm: fix wrong signal octets encoding in MSC
+    - tty: n_gsm: fix missing tty wakeup in convergence layer type 2
+    - tty: n_gsm: fix reset fifo race condition
+    - tty: n_gsm: fix incorrect UA handling
+    - tty: n_gsm: fix software flow control handling
+    - perf symbol: Remove arch__symbols__fixup_end()
+    - eeprom: at25: Use DMA safe buffers
+    - objtool: Fix code relocs vs weak symbols
+    - objtool: Fix type of reloc::addend
+    - powerpc/64: Add UADDR64 relocation support
+    - Linux 5.15.38
+
+  * Jammy update: v5.15.37 upstream stable release (LP: #1976135)
+    - floppy: disable FDRAWCMD by default
+    - [Config] updateconfigs for BLK_DEV_FD_RAWCMD
+    - bpf: Introduce composable reg, ret and arg types.
+    - bpf: Replace ARG_XXX_OR_NULL with ARG_XXX | PTR_MAYBE_NULL
+    - bpf: Replace RET_XXX_OR_NULL with RET_XXX | PTR_MAYBE_NULL
+    - bpf: Replace PTR_TO_XXX_OR_NULL with PTR_TO_XXX | PTR_MAYBE_NULL
+    - bpf: Introduce MEM_RDONLY flag
+    - bpf: Convert PTR_TO_MEM_OR_NULL to composable types.
+    - bpf: Make per_cpu_ptr return rdonly PTR_TO_MEM.
+    - bpf: Add MEM_RDONLY for helper args that are pointers to rdonly mem.
+    - bpf/selftests: Test PTR_TO_RDONLY_MEM
+    - bpf: Fix crash due to out of bounds access into reg2btf_ids.
+    - spi: cadence-quadspi: fix write completion support
+    - ARM: dts: socfpga: change qspi to "intel,socfpga-qspi"
+    - mm: kfence: fix objcgs vector allocation
+    - gup: Turn fault_in_pages_{readable,writeable} into
+      fault_in_{readable,writeable}
+    - iov_iter: Turn iov_iter_fault_in_readable into fault_in_iov_iter_readable
+    - iov_iter: Introduce fault_in_iov_iter_writeable
+    - gfs2: Add wrapper for iomap_file_buffered_write
+    - gfs2: Clean up function may_grant
+    - gfs2: Introduce flag for glock holder auto-demotion
+    - gfs2: Move the inode glock locking to gfs2_file_buffered_write
+    - gfs2: Eliminate ip->i_gh
+    - gfs2: Fix mmap + page fault deadlocks for buffered I/O
+    - iomap: Fix iomap_dio_rw return value for user copies
+    - iomap: Support partial direct I/O on user copy failures
+    - iomap: Add done_before argument to iomap_dio_rw
+    - gup: Introduce FOLL_NOFAULT flag to disable page faults
+    - iov_iter: Introduce nofault flag to disable page faults
+    - gfs2: Fix mmap + page fault deadlocks for direct I/O
+    - btrfs: fix deadlock due to page faults during direct IO reads and writes
+    - btrfs: fallback to blocking mode when doing async dio over multiple extents
+    - mm: gup: make fault_in_safe_writeable() use fixup_user_fault()
+    - selftests/bpf: Add test for reg2btf_ids out of bounds access
+    - Linux 5.15.37
+
+  * CVE-2022-1789
+    - KVM: x86/mmu: fix NULL pointer dereference on guest INVPCID
+
+  * Jammy update: v5.15.36 upstream stable release (LP: #1972905)
+    - block: simplify the block device syncing code
+    - xfs: return errors in xfs_fs_sync_fs
+    - dma-mapping: remove bogus test for pfn_valid from dma_map_resource
+    - arm64/mm: drop HAVE_ARCH_PFN_VALID
+    - etherdevice: Adjust ether_addr* prototypes to silence -Wstringop-overead
+    - mm: page_alloc: fix building error on -Werror=array-compare
+    - perf tools: Fix segfault accessing sample_id xyarray
+    - mm, kfence: support kmem_dump_obj() for KFENCE objects
+    - gfs2: assign rgrp glock before compute_bitstructs
+    - scsi: ufs: core: scsi_get_lba() error fix
+    - ALSA: usb-audio: Clear MIDI port active flag after draining
+    - ALSA: hda/realtek: Add quirk for Clevo NP70PNP
+    - ASoC: atmel: Remove system clock tree configuration for at91sam9g20ek
+    - ASoC: topology: Correct error handling in soc_tplg_dapm_widget_create()
+    - ASoC: rk817: Use devm_clk_get() in rk817_platform_probe
+    - ASoC: msm8916-wcd-digital: Check failure for devm_snd_soc_register_component
+    - ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use
+    - dmaengine: idxd: fix device cleanup on disable
+    - dmaengine: imx-sdma: Fix error checking in sdma_event_remap
+    - dmaengine: mediatek:Fix PM usage reference leak of
+      mtk_uart_apdma_alloc_chan_resources
+    - dmaengine: dw-edma: Fix unaligned 64bit access
+    - spi: spi-mtk-nor: initialize spi controller after resume
+    - esp: limit skb_page_frag_refill use to a single page
+    - spi: cadence-quadspi: fix incorrect supports_op() return value
+    - igc: Fix infinite loop in release_swfw_sync
+    - igc: Fix BUG: scheduling while atomic
+    - igc: Fix suspending when PTM is active
+    - ALSA: hda/hdmi: fix warning about PCM count when used with SOF
+    - rxrpc: Restore removed timer deletion
+    - net/smc: Fix sock leak when release after smc_shutdown()
+    - net/packet: fix packet_sock xmit return value checking
+    - ip6_gre: Avoid updating tunnel->tun_hlen in __gre6_xmit()
+    - ip6_gre: Fix skb_under_panic in __gre6_xmit()
+    - net: restore alpha order to Ethernet devices in config
+    - net/sched: cls_u32: fix possible leak in u32_init_knode()
+    - l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using
+      netdev_master_upper_dev_get_rcu
+    - ipv6: make ip6_rt_gc_expire an atomic_t
+    - can: isotp: stop timeout monitoring when no first frame was sent
+    - net: dsa: hellcreek: Calculate checksums in tagger
+    - net: mscc: ocelot: fix broken IP multicast flooding
+    - netlink: reset network and mac headers in netlink_dump()
+    - drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in
+      intel_psr2_config_valid() fails
+    - net: stmmac: Use readl_poll_timeout_atomic() in atomic state
+    - dmaengine: idxd: add RO check for wq max_batch_size write
+    - dmaengine: idxd: add RO check for wq max_transfer_size write
+    - dmaengine: idxd: skip clearing device context when device is read-only
+    - selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
+    - arm64: mm: fix p?d_leaf()
+    - ARM: vexpress/spc: Avoid negative array index when !SMP
+    - reset: renesas: Check return value of reset_control_deassert()
+    - reset: tegra-bpmp: Restore Handle errors in BPMP response
+    - platform/x86: samsung-laptop: Fix an unsigned comparison which can never be
+      negative
+    - ALSA: usb-audio: Fix undefined behavior due to shift overflowing the
+      constant
+    - drm/msm/disp: check the return value of kzalloc()
+    - arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
+    - vxlan: fix error return code in vxlan_fdb_append
+    - cifs: Check the IOCB_DIRECT flag, not O_DIRECT
+    - mt76: Fix undefined behavior due to shift overflowing the constant
+    - brcmfmac: sdio: Fix undefined behavior due to shift overflowing the constant
+    - dpaa_eth: Fix missing of_node_put in dpaa_get_ts_info()
+    - drm/msm/mdp5: check the return of kzalloc()
+    - net: macb: Restart tx only if queue pointer is lagging
+    - scsi: iscsi: Release endpoint ID when its freed
+    - scsi: iscsi: Merge suspend fields
+    - scsi: iscsi: Fix NOP handling during conn recovery
+    - scsi: qedi: Fix failed disconnect handling
+    - stat: fix inconsistency between struct stat and struct compat_stat
+    - VFS: filename_create(): fix incorrect intent.
+    - nvme: add a quirk to disable namespace identifiers
+    - nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
+    - nvme-pci: disable namespace identifiers for Qemu controllers
+    - EDAC/synopsys: Read the error count from the correct register
+    - mm/memory-failure.c: skip huge_zero_page in memory_failure()
+    - memcg: sync flush only if periodic flush is delayed
+    - mm, hugetlb: allow for "high" userspace addresses
+    - oom_kill.c: futex: delay the OOM reaper to allow time for proper futex
+      cleanup
+    - mm/mmu_notifier.c: fix race in mmu_interval_notifier_remove()
+    - ata: pata_marvell: Check the 'bmdma_addr' beforing reading
+    - dma: at_xdmac: fix a missing check on list iterator
+    - dmaengine: imx-sdma: fix init of uart scripts
+    - net: atlantic: invert deep par in pm functions, preventing null derefs
+    - Input: omap4-keypad - fix pm_runtime_get_sync() error checking
+    - scsi: sr: Do not leak information in ioctl
+    - sched/pelt: Fix attach_entity_load_avg() corner case
+    - perf/core: Fix perf_mmap fail when CONFIG_PERF_USE_VMALLOC enabled
+    - drm/panel/raspberrypi-touchscreen: Avoid NULL deref if not initialised
+    - drm/panel/raspberrypi-touchscreen: Initialise the bridge in prepare
+    - KVM: PPC: Fix TCE handling for VFIO
+    - drm/vc4: Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
+    - powerpc/perf: Fix power9 event alternatives
+    - powerpc/perf: Fix power10 event alternatives
+    - perf script: Always allow field 'data_src' for auxtrace
+    - perf report: Set PERF_SAMPLE_DATA_SRC bit for Arm SPE event
+    - xtensa: patch_text: Fixup last cpu should be master
+    - xtensa: fix a7 clobbering in coprocessor context load/store
+    - openvswitch: fix OOB access in reserve_sfa_size()
+    - ASoC: soc-dapm: fix two incorrect uses of list iterator
+    - e1000e: Fix possible overflow in LTR decoding
+    - ARC: entry: fix syscall_trace_exit argument
+    - arm_pmu: Validate single/group leader events
+    - KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
+    - KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
+    - KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
+    - KVM: SVM: Flush when freeing encrypted pages even on SME_COHERENT CPUs
+    - netfilter: conntrack: convert to refcount_t api
+    - netfilter: conntrack: avoid useless indirection during conntrack destruction
+    - ext4: fix fallocate to use file_modified to update permissions consistently
+    - ext4: fix symlink file size not match to file content
+    - ext4: fix use-after-free in ext4_search_dir
+    - ext4, doc: fix incorrect h_reserved size
+    - ext4: fix overhead calculation to account for the reserved gdt blocks
+    - ext4: force overhead calculation if the s_overhead_cluster makes no sense
+    - netfilter: nft_ct: fix use after free when attaching zone template
+    - jbd2: fix a potential race while discarding reserved buffers after an abort
+    - spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and
+      controller
+    - block/compat_ioctl: fix range check in BLKGETSIZE
+    - arm64: dts: qcom: add IPA qcom,qmp property
+    - Linux 5.15.36
+
+  * Aquantia GbE LAN driver causes UBSAN error during kernel boot
+    (LP: #1958770) // Jammy update: v5.15.36 upstream stable release
+    (LP: #1972905)
+    - net: atlantic: Avoid out-of-bounds indexing
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 22 Jun 2022 14:42:28 +0200
+
+linux (5.15.0-40.43) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-40.43 -proposed tracker (LP: #1978610)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2022.05.30)
+
+  * [SRU][OEM-5.14/OEM-5.17/J][PATCH 0/2] Fix system hangs after s2idle on AMD
+    A+A GPU (LP: #1975804)
+    - Revert "drm/amd/pm: keep the BACO feature enabled for suspend"
+    - drm/amd: Don't reset dGPUs if the system is going to s2idle
+
+  * [SRU][OEM-5.14/OEM-5.17/J][PATCH 0/1] Read the discovery registers for
+    AMD_SFH (LP: #1975798)
+    - HID: amd_sfh: Add support for sensor discovery
+
+  * [UBUNTU 20.04] CPU-MF: add extended counter set definitions for new IBM z16
+    (LP: #1974433)
+    - s390/cpumf: add new extended counter set for IBM z16
+
+  * [UBUNTU 20.04] KVM nesting support leaks too much memory, might result in
+    stalls during cleanup (LP: #1974017)
+    - KVM: s390: vsie/gmap: reduce gmap_rmap overhead
+
+  * [UBUNTU 20.04] Null Pointer issue in nfs code running Ubuntu on IBM Z
+    (LP: #1968096)
+    - NFS: Fix up nfs_ctx_key_to_expire()
+
+  * Fix REG_WAIT timeout for Yellow Carp (LP: #1971417)
+    - drm/amd/display: Clear encoder assignments when state cleared.
+    - drm/amd/display: fix stale info in link encoder assignment
+    - drm/amd/display: Query all entries in assignment table during updates.
+    - drm/amd/display: Initialise encoder assignment when initialising dc_state
+
+  * Enable hotspot feature for Realtek 8821CE (LP: #1969326)
+    - rtw88: Add update beacon flow for AP mode
+    - rtw88: 8821c: Enable TX report for management frames
+    - rtw88: do PHY calibration while starting AP
+    - rtw88: 8821c: fix debugfs rssi value
+    - rtw88: add ieee80211:sta_rc_update ops
+
+  * prevent kernel panic with overlayfs + shiftfs (LP: #1973620)
+    - SAUCE: overlayfs: prevent dereferencing struct file in ovl_vm_prfile_set()
+
+  * disable Intel DMA remapping by default (LP: #1971699)
+    - Revert "UBUNTU: [Config] enable Intel DMA remapping options by default"
+
+  * Mute/mic LEDs no function on Elitebook 630 (LP: #1974111)
+    - ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machine
+
+  * [Regression] Real-time Kernel Build Failure (LP: #1972899)
+    - x86/mm: Include spinlock_t definition in pgtable.
+
+  * build backport-iwlwifi-dkms as linux-modules-iwlwifi-ABI (LP: #1969434)
+    - [Packaging] support standalone dkms module builds
+    - [Packaging] drop do_<mod> arch specific configs
+
+  * IPU6 camera has no function on Andrews MLK (LP: #1964983)
+    - SAUCE: IPU6: 2022-03-11 alpha release for Andrews MLK
+    - [Config] IPU6: enable OV02C10 sensor
+    - SAUCE: IPU6: 2022-04-01 Andrews MLK PV release
+    - SAUCE: spi: ljca: return when a sub-transaction first failed
+    - SACUE: ljca: disable parallelly stub write
+    - SAUCE: ljca: fix race condition issue in runtime PM
+    - SAUCE: i2c-ljca: fix a null pointer access issue on tgl
+    - SAUCE: ljca: fix a typo issue
+    - SAUCE: ljca: assume stub enum failed as a warning
+    - SAUCE: mei: cleanup header file including
+    - SAUCE: intel_ulpss: Replaced by LJCA and remove
+    - [Config] drop intel_ulpss in favor of by LJCA
+
+  * multiple UBSAN warnings in Intel IPU6 camera driver at boot (LP: #1958006)
+    - SAUCE: media: pci: intel: Avoid UBSAN warnings of index bound and shift
+
+  * Support Intel IPU6 MIPI camera on Alder Lake platforms (LP: #1955383)
+    - SAUCE: intel ipu drivers first release
+    - SAUCE: IPU driver release WW48
+    - SAUCE: IPU driver release WW48 with MCU
+    - SAUCE: IPU driver release WW52
+    - SAUCE: IPU driver release WW04
+    - SAUCE: IPU driver release WW14
+    - SAUCE: Fix ov01a1s output mirror issue
+    - SAUCE: integrate IPU6 builds
+    - [Config] updateconfigs for IPU6 driver
+    - SAUCE: Fix ov01a1s IQ issues
+    - SAUCE: intel/ipu6: Remove unnecessary video devices
+    - SAUCE: change power control driver to acpi driver
+    - SAUCE: IPU6 driver release for kernel 5.13
+    - SAUCE: sensor HM11b1 brightness bugfix
+    - SAUCE: Fix build error on Kernel 5.13
+    - SAUCE: IPU6 driver release for kernel 5.14 on 2021-11-01
+    - [Config] IPU6: enable OV01A10 sensor
+    - SAUCE: Fix build error for kernel 5.15
+    - SAUCE: intel visual sensing controller(VSC) driver first release
+    - [Config] ivsc: enable Intel VSC drivers
+    - SAUCE: ivsc: return error when device not ready
+    - SAUCE: ivsc: add soft dependencies for intel_vsc module
+    - SAUCE: ljca: switch wait event to uninterruptible
+    - SAUCE: mei-vsc: switch wait event to uninterruptible
+    - SAUCE: mei_vsc: add ACPI HID for ADL
+    - SAUCE: ljca: add multi ACPI HID support
+    - SAUCE: ivsc: add delay for acquire camera to wait firmware ready
+    - SAUCE: mei_vsc: distinguish platform with different camera sensor
+    - SAUCE: i2c-ljca: fix a potential issue
+    - SAUCE: ljca: disable autosuspend by default
+    - [Config] make Intel IPU6 modules amd64 only
+    - SAUCE: IPU6: drop unnecessary cflags manipulation
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 15 Jun 2022 14:14:21 +0200
+
+linux (5.15.0-39.42) jammy; urgency=medium
+
+  * CVE-2022-21123 // CVE-2022-21125 // CVE-2022-21166
+    - Documentation: Add documentation for Processor MMIO Stale Data
+    - x86/speculation/mmio: Enumerate Processor MMIO Stale Data bug
+    - x86/speculation: Add a common function for MD_CLEAR mitigation update
+    - x86/speculation/mmio: Add mitigation for Processor MMIO Stale Data
+    - x86/bugs: Group MDS, TAA & Processor MMIO Stale Data mitigations
+    - x86/speculation/mmio: Enable CPU Fill buffer clearing on idle
+    - x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data
+    - x86/speculation/srbds: Update SRBDS mitigation selection
+    - x86/speculation/mmio: Reuse SRBDS mitigation for SBDS
+    - KVM: x86/speculation: Disable Fill buffer clear within guests
+    - x86/speculation/mmio: Print SMT warning
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Thu, 09 Jun 2022 11:36:27 -0300
+
+linux (5.15.0-37.39) jammy; urgency=medium
+
+  * netfilter newset OOB write (LP: #1976363)
+    - netfilter: nf_tables: sanitize nft_set_desc_concat_parse()
+
+  * CVE-2022-1966
+    - netfilter: nf_tables: disallow non-stateful expression in sets earlier
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Wed, 01 Jun 2022 14:49:43 -0300
+
+linux (5.15.0-35.36) jammy; urgency=medium
+
+  * CVE-2022-21499
+    - SAUCE: debug: Lock down kgdb
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Fri, 20 May 2022 21:43:49 -0300
+
+linux (5.15.0-34.35) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-34.35 -proposed tracker (LP: #1974322)
+
+  * AMD APU s2idle is broken after the ASIC reset fix (LP: #1972134)
+    - drm/amdgpu: unify BO evicting method in amdgpu_ttm
+    - drm/amdgpu: explicitly check for s0ix when evicting resources
+
+  * amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517
+    (LP: #1971597)
+    - gpio: Request interrupts after IRQ is initialized
+
+  * config CONFIG_HISI_PMU for  kunpeng920 (LP: #1956086)
+    - [Config] CONFIG_HISI_PMU=m
+
+  * Mute/mic LEDs no function on EliteBook G9 platfroms (LP: #1970552)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs support for HP Laptops
+
+  * network-manager/1.36.4-2ubuntu1 ADT test failure with linux/5.15.0-28.29
+    (LP: #1971418)
+    - Revert "rfkill: make new event layout opt-in"
+
+  * PCIE LnkCtl ASPM not enabled under VMD mode for Alder Lake platforms
+    (LP: #1942160)
+    - SAUCE: vmd: fixup bridge ASPM by driver name instead
+
+  * Mute/mic LEDs no function on HP EliteBook 845/865 G9 (LP: #1970178)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook
+      845/865 G9
+
+  * Enable headset mic on Lenovo P360 (LP: #1967069)
+    - ALSA: hda/realtek: Enable headset mic on Lenovo P360
+
+  * WCN6856 BT keep in OFF state after coldboot system (LP: #1967067)
+    - Bluetooth: btusb: Improve stability for QCA devices
+
+  * Screen sometimes can't update [Failed to post KMS update: CRTC property
+    (GAMMA_LUT) not found] (LP: #1967274)
+    - drm/i915/xelpd: Enable Pipe color support for D13 platform
+    - drm/i915: Use unlocked register accesses for LUT loads
+    - drm/i915/xelpd: Enable Pipe Degamma
+    - drm/i915/xelpd: Add Pipe Color Lut caps to platform config
+
+  * Jammy update: v5.15.35 upstream stable release (LP: #1969857)
+    - drm/amd/display: Add pstate verification and recovery for DCN31
+    - drm/amd/display: Fix p-state allow debug index on dcn31
+    - hamradio: defer 6pack kfree after unregister_netdev
+    - hamradio: remove needs_free_netdev to avoid UAF
+    - cpuidle: PSCI: Move the `has_lpi` check to the beginning of the function
+    - ACPI: processor idle: Check for architectural support for LPI
+    - ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40
+    - btrfs: remove unused parameter nr_pages in add_ra_bio_pages()
+    - btrfs: remove no longer used counter when reading data page
+    - btrfs: remove unused variable in btrfs_{start,write}_dirty_block_groups()
+    - soc: qcom: aoss: Expose send for generic usecase
+    - dt-bindings: net: qcom,ipa: add optional qcom,qmp property
+    - net: ipa: request IPA register values be retained
+    - btrfs: release correct delalloc amount in direct IO write path
+    - ALSA: core: Add snd_card_free_on_error() helper
+    - ALSA: sis7019: Fix the missing error handling
+    - ALSA: ali5451: Fix the missing snd_card_free() call at probe error
+    - ALSA: als300: Fix the missing snd_card_free() call at probe error
+    - ALSA: als4000: Fix the missing snd_card_free() call at probe error
+    - ALSA: atiixp: Fix the missing snd_card_free() call at probe error
+    - ALSA: au88x0: Fix the missing snd_card_free() call at probe error
+    - ALSA: aw2: Fix the missing snd_card_free() call at probe error
+    - ALSA: azt3328: Fix the missing snd_card_free() call at probe error
+    - ALSA: bt87x: Fix the missing snd_card_free() call at probe error
+    - ALSA: ca0106: Fix the missing snd_card_free() call at probe error
+    - ALSA: cmipci: Fix the missing snd_card_free() call at probe error
+    - ALSA: cs4281: Fix the missing snd_card_free() call at probe error
+    - ALSA: cs5535audio: Fix the missing snd_card_free() call at probe error
+    - ALSA: echoaudio: Fix the missing snd_card_free() call at probe error
+    - ALSA: emu10k1x: Fix the missing snd_card_free() call at probe error
+    - ALSA: ens137x: Fix the missing snd_card_free() call at probe error
+    - ALSA: es1938: Fix the missing snd_card_free() call at probe error
+    - ALSA: es1968: Fix the missing snd_card_free() call at probe error
+    - ALSA: fm801: Fix the missing snd_card_free() call at probe error
+    - ALSA: galaxy: Fix the missing snd_card_free() call at probe error
+    - ALSA: hdsp: Fix the missing snd_card_free() call at probe error
+    - ALSA: hdspm: Fix the missing snd_card_free() call at probe error
+    - ALSA: ice1724: Fix the missing snd_card_free() call at probe error
+    - ALSA: intel8x0: Fix the missing snd_card_free() call at probe error
+    - ALSA: intel_hdmi: Fix the missing snd_card_free() call at probe error
+    - ALSA: korg1212: Fix the missing snd_card_free() call at probe error
+    - ALSA: lola: Fix the missing snd_card_free() call at probe error
+    - ALSA: lx6464es: Fix the missing snd_card_free() call at probe error
+    - ALSA: maestro3: Fix the missing snd_card_free() call at probe error
+    - ALSA: oxygen: Fix the missing snd_card_free() call at probe error
+    - ALSA: riptide: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme32: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme9652: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme96: Fix the missing snd_card_free() call at probe error
+    - ALSA: sc6000: Fix the missing snd_card_free() call at probe error
+    - ALSA: sonicvibes: Fix the missing snd_card_free() call at probe error
+    - ALSA: via82xx: Fix the missing snd_card_free() call at probe error
+    - ALSA: usb-audio: Cap upper limits of buffer/period bytes for implicit fb
+    - ALSA: nm256: Don't call card private_free at probe error path
+    - drm/msm: Add missing put_task_struct() in debugfs path
+    - firmware: arm_scmi: Remove clear channel call on the TX channel
+    - memory: atmel-ebi: Fix missing of_node_put in atmel_ebi_probe
+    - Revert "ath11k: mesh: add support for 256 bitmap in blockack frames in 11ax"
+    - firmware: arm_scmi: Fix sorting of retrieved clock rates
+    - media: rockchip/rga: do proper error checking in probe
+    - SUNRPC: Fix the svc_deferred_event trace class
+    - net/sched: flower: fix parsing of ethertype following VLAN header
+    - veth: Ensure eth header is in skb's linear part
+    - gpiolib: acpi: use correct format characters
+    - cifs: release cached dentries only if mount is complete
+    - net: mdio: don't defer probe forever if PHY IRQ provider is missing
+    - mlxsw: i2c: Fix initialization error flow
+    - net/sched: fix initialization order when updating chain 0 head
+    - net: dsa: felix: suppress -EPROBE_DEFER errors
+    - net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link
+    - net/sched: taprio: Check if socket flags are valid
+    - cfg80211: hold bss_lock while updating nontrans_list
+    - netfilter: nft_socket: make cgroup match work in input too
+    - drm/msm: Fix range size vs end confusion
+    - drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()
+    - drm/msm/dp: add fail safe mode outside of event_mutex context
+    - net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
+    - scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
+    - scsi: pm80xx: Enable upper inbound, outbound queues
+    - scsi: iscsi: Move iscsi_ep_disconnect()
+    - scsi: iscsi: Fix offload conn cleanup when iscsid restarts
+    - scsi: iscsi: Fix endpoint reuse regression
+    - scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
+    - scsi: iscsi: Fix unbound endpoint error handling
+    - sctp: Initialize daddr on peeled off socket
+    - netfilter: nf_tables: nft_parse_register can return a negative value
+    - ALSA: ad1889: Fix the missing snd_card_free() call at probe error
+    - ALSA: mtpav: Don't call card private_free at probe error path
+    - io_uring: move io_uring_rsrc_update2 validation
+    - io_uring: verify that resv2 is 0 in io_uring_rsrc_update2
+    - io_uring: verify pad field is 0 in io_get_ext_arg
+    - testing/selftests/mqueue: Fix mq_perf_tests to free the allocated cpu set
+    - ALSA: usb-audio: Increase max buffer size
+    - ALSA: usb-audio: Limit max buffer and period sizes per time
+    - perf tools: Fix misleading add event PMU debug message
+    - macvlan: Fix leaking skb in source mode with nodst option
+    - net: ftgmac100: access hardware register after clock ready
+    - nfc: nci: add flush_workqueue to prevent uaf
+    - cifs: potential buffer overflow in handling symlinks
+    - dm mpath: only use ktime_get_ns() in historical selector
+    - vfio/pci: Fix vf_token mechanism when device-specific VF drivers are used
+    - net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
+    - block: fix offset/size check in bio_trim()
+    - drm/amd: Add USBC connector ID
+    - btrfs: fix fallocate to use file_modified to update permissions consistently
+    - btrfs: do not warn for free space inode in cow_file_range
+    - drm/amdgpu: conduct a proper cleanup of PDB bo
+    - drm/amdgpu/gmc: use PCI BARs for APUs in passthrough
+    - drm/amd/display: fix audio format not updated after edid updated
+    - drm/amd/display: FEC check in timing validation
+    - drm/amd/display: Update VTEM Infopacket definition
+    - drm/amdkfd: Fix Incorrect VMIDs passed to HWS
+    - drm/amdgpu/vcn: improve vcn dpg stop procedure
+    - drm/amdkfd: Check for potential null return of kmalloc_array()
+    - Drivers: hv: vmbus: Deactivate sysctl_record_panic_msg by default in
+      isolated guests
+    - PCI: hv: Propagate coherence from VMbus device to PCI device
+    - Drivers: hv: vmbus: Prevent load re-ordering when reading ring buffer
+    - scsi: target: tcmu: Fix possible page UAF
+    - scsi: lpfc: Fix queue failures when recovering from PCI parity error
+    - scsi: ibmvscsis: Increase INITIAL_SRP_LIMIT to 1024
+    - net: micrel: fix KS8851_MLL Kconfig
+    - ata: libata-core: Disable READ LOG DMA EXT for Samsung 840 EVOs
+    - gpu: ipu-v3: Fix dev_dbg frequency output
+    - regulator: wm8994: Add an off-on delay for WM8994 variant
+    - arm64: alternatives: mark patch_alternative() as `noinstr`
+    - tlb: hugetlb: Add more sizes to tlb_remove_huge_tlb_entry
+    - net: axienet: setup mdio unconditionally
+    - Drivers: hv: balloon: Disable balloon and hot-add accordingly
+    - net: usb: aqc111: Fix out-of-bounds accesses in RX fixup
+    - myri10ge: fix an incorrect free for skb in myri10ge_sw_tso
+    - spi: cadence-quadspi: fix protocol setup for non-1-1-X operations
+    - drm/amd/display: Enable power gating before init_pipes
+    - drm/amd/display: Revert FEC check in validation
+    - drm/amd/display: Fix allocate_mst_payload assert on resume
+    - drbd: set QUEUE_FLAG_STABLE_WRITES
+    - scsi: mpt3sas: Fail reset operation if config request timed out
+    - scsi: mvsas: Add PCI ID of RocketRaid 2640
+    - scsi: megaraid_sas: Target with invalid LUN ID is deleted during scan
+    - drivers: net: slip: fix NPD bug in sl_tx_timeout()
+    - io_uring: zero tag on rsrc removal
+    - io_uring: use nospec annotation for more indexes
+    - perf/imx_ddr: Fix undefined behavior due to shift overflowing the constant
+    - mm/secretmem: fix panic when growing a memfd_secret
+    - mm, page_alloc: fix build_zonerefs_node()
+    - mm: fix unexpected zeroed page mapping with zram swap
+    - mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
+    - KVM: x86/mmu: Resolve nx_huge_pages when kvm.ko is loaded
+    - SUNRPC: Fix NFSD's request deferral on RDMA transports
+    - memory: renesas-rpc-if: fix platform-device leak in error path
+    - gcc-plugins: latent_entropy: use /dev/urandom
+    - cifs: verify that tcon is valid before dereference in cifs_kill_sb
+    - ath9k: Properly clear TX status area before reporting to mac80211
+    - ath9k: Fix usage of driver-private space in tx_info
+    - btrfs: fix root ref counts in error handling in btrfs_get_root_ref
+    - btrfs: mark resumed async balance as writing
+    - ALSA: hda/realtek: Add quirk for Clevo PD50PNT
+    - ALSA: hda/realtek: add quirk for Lenovo Thinkpad X12 speakers
+    - ALSA: pcm: Test for "silence" field in struct "pcm_format_data"
+    - nl80211: correctly check NL80211_ATTR_REG_ALPHA2 size
+    - ipv6: fix panic when forwarding a pkt with no in6 dev
+    - drm/amd/display: don't ignore alpha property on pre-multiplied mode
+    - drm/amdgpu: Enable gfxoff quirk on MacBook Pro
+    - x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits
+    - x86/tsx: Disable TSX development mode at boot
+    - genirq/affinity: Consider that CPUs on nodes can be unbalanced
+    - tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
+    - ARM: davinci: da850-evm: Avoid NULL pointer dereference
+    - dm integrity: fix memory corruption when tag_size is less than digest size
+    - i2c: dev: check return value when calling dev_set_name()
+    - smp: Fix offline cpu check in flush_smp_call_function_queue()
+    - i2c: pasemi: Wait for write xfers to finish
+    - dt-bindings: net: snps: remove duplicate name
+    - timers: Fix warning condition in __run_timers()
+    - dma-direct: avoid redundant memory sync for swiotlb
+    - drm/i915: Sunset igpu legacy mmap support based on GRAPHICS_VER_FULL
+    - cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
+    - soc: qcom: aoss: Fix missing put_device call in qmp_get
+    - net: ipa: fix a build dependency
+    - cpufreq: intel_pstate: ITMT support for overclocked system
+    - ax25: add refcount in ax25_dev to avoid UAF bugs
+    - ax25: fix reference count leaks of ax25_dev
+    - ax25: fix UAF bugs of net_device caused by rebinding operation
+    - ax25: Fix refcount leaks caused by ax25_cb_del()
+    - ax25: fix UAF bug in ax25_send_control()
+    - ax25: fix NPD bug in ax25_disconnect
+    - ax25: Fix NULL pointer dereferences in ax25 timers
+    - ax25: Fix UAF bugs in ax25 timers
+    - Linux 5.15.35
+
+  * CONFIG_SND_COMPRESS_OFFLOAD missing in jammy/ppc64el kernel config
+    (LP: #1969807)
+    - [Config] updateconfigs for SND_COMPRESS_OFFLOAD (ppc64el)
+
+  * Micmute LED support for Zbook Fury 16 G9 (LP: #1968892)
+    - ALSA: hda/realtek: Add mute and micmut LED support for Zbook Fury 17 G9
+
+  * Fix broken HDMI audio on AMD PRO VII after S3 (LP: #1968475)
+    - drm/amdgpu: don't set s3 and s0ix at the same time
+    - drm/amdgpu: Ensure HDA function is suspended before ASIC reset
+
+  * [Ubuntu 22.04] mpi3mr: Request to include latest bug fixes (LP: #1967116)
+    - scsi: mpi3mr: Clean up mpi3mr_print_ioc_info()
+    - scsi: mpi3mr: Use scnprintf() instead of snprintf()
+    - scsi: mpi3mr: Add debug APIs based on logging_level bits
+    - scsi: mpi3mr: Replace spin_lock() with spin_lock_irqsave()
+    - scsi: mpi3mr: Don't reset IOC if cmnds flush with reset status
+    - scsi: mpi3mr: Update MPI3 headers - part1
+    - scsi: mpi3mr: Update MPI3 headers - part2
+    - scsi: mpi3mr: Add support for PCIe Managed Switch SES device
+    - scsi: mpi3mr: Do access status validation before adding devices
+    - scsi: mpi3mr: Increase internal cmnds timeout to 60s
+    - scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
+    - scsi: mpi3mr: Display IOC firmware package version
+    - scsi: mpi3mr: Fault IOC when internal command gets timeout
+    - scsi: mpi3mr: Code refactor of IOC init - part1
+    - scsi: mpi3mr: Code refactor of IOC init - part2
+    - scsi: mpi3mr: Handle offline FW activation in graceful manner
+    - scsi: mpi3mr: Add IOC reinit function
+    - scsi: mpi3mr: Detect async reset that occurred in firmware
+    - scsi: mpi3mr: Gracefully handle online FW update operation
+    - scsi: mpi3mr: Add Event acknowledgment logic
+    - scsi: mpi3mr: Support Prepare for Reset event
+    - scsi: mpi3mr: Print cable mngnt and temp threshold events
+    - scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
+    - scsi: mpi3mr: Use TM response codes from MPI3 headers
+    - scsi: mpi3mr: Enhanced Task Management Support Reply handling
+    - scsi: mpi3mr: Bump driver version to 8.0.0.61.0
+    - scsi: mpi3mr: Fix some spelling mistakes
+    - scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
+    - scsi: mpi3mr: Fix deadlock while canceling the fw event
+    - scsi: mpi3mr: Fix printing of pending I/O count
+    - scsi: mpi3mr: Update MPI3 headers
+    - scsi: mpi3mr: Fix hibernation issue
+    - scsi: mpi3mr: Fix cmnd getting marked as in use forever
+    - scsi: mpi3mr: Update the copyright year
+    - scsi: mpi3mr: Bump driver version to 8.0.0.68.0
+    - scsi: mpi3mr: Fix flushing !WQ_MEM_RECLAIM events warning
+
+  * Support AMD P-State cpufreq control mechanism (LP: #1956509)
+    - x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature
+      flag
+    - x86/msr: Add AMD CPPC MSR definitions
+    - ACPI: CPPC: Implement support for SystemIO registers
+    - ACPI: CPPC: Add CPPC enable register function
+    - cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future
+      processors
+    - cpufreq: amd-pstate: Add fast switch function for AMD P-State
+    - cpufreq: amd-pstate: Introduce the support for the processors with shared
+      memory solution
+    - cpufreq: amd-pstate: Add trace for AMD P-State module
+    - cpufreq: amd-pstate: Add boost mode support for AMD P-State
+    - cpufreq: amd-pstate: Add AMD P-State frequencies attributes
+    - cpufreq: amd-pstate: Add AMD P-State performance attributes
+    - Documentation: amd-pstate: Add AMD P-State driver introduction
+    - MAINTAINERS: Add AMD P-State driver maintainer entry
+    - cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
+    - cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
+    - [Config] enable X86_AMD_PSTATE as built-in on amd64
+
+  * Bolt doesn't work with native USB4 hosts (LP: #1962349)
+    - thunderbolt: Retry DROM reads for more failure scenarios
+    - thunderbolt: Do not resume routers if UID is not set
+    - thunderbolt: Do not make DROM read success compulsory
+    - PCI/ACPI: Allow D3 only if Root Port can signal and wake from D3
+
+  * linux-image-5.0.0-35-generic breaks checkpointing of container
+    (LP: #1857257) // re-apply missing overlayfs SAUCE patch (LP: #1967924)
+    - SAUCE: overlayfs: fix incorrect mnt_id of files opened from map_files
+
+  * [Jammy, mlx5, ConnectX-7] add CX7 support for software steering
+    (LP: #1966194)
+    - net/mlx5: DR, Fix vport number data type to u16
+    - net/mlx5: DR, Replace local WIRE_PORT macro with the existing
+      MLX5_VPORT_UPLINK
+    - net/mlx5: DR, Add missing query for vport 0
+    - net/mlx5: DR, Align error messages for failure to obtain vport caps
+    - net/mlx5: DR, Support csum recalculation flow table on SFs
+    - net/mlx5: DR, Add support for SF vports
+    - net/mlx5: DR, Increase supported num of actions to 32
+    - net/mlx5: DR, Fix typo 'offeset' to 'offset'
+    - net/mlx5: DR, init_next_match only if needed
+    - net/mlx5: DR, Add missing string for action type SAMPLER
+    - net/mlx5: DR, Add check for unsupported fields in match param
+    - net/mlx5: Introduce new uplink destination type
+    - net/mlx5: DR, Handle eswitch manager and uplink vports separately
+    - net/mlx5: DR, Fix querying eswitch manager vport for ECPF
+    - net/mlx5: DR, Fix check for unsupported fields in match param
+    - net/mlx5: DR, Fix error flow in creating matcher
+    - net/mlx5: DR, Fix lower case macro prefix "mlx5_" to "MLX5_"
+    - net/mlx5: DR, Remove unused struct member in matcher
+    - net/mlx5: DR, Rename list field in matcher struct to list_node
+    - net/mlx5: DR, Add check for flex parser ID value
+    - net/mlx5: DR, Add missing reserved fields to dr_match_param
+    - net/mlx5: DR, Add support for dumping steering info
+    - net/mlx5: DR, Add support for UPLINK destination type
+    - net/mlx5: DR, Warn on failure to destroy objects due to refcount
+    - net/mlx5: Add misc5 flow table match parameters
+    - net/mlx5: DR, Add misc5 to match_param structs
+    - net/mlx5: DR, Support matching on tunnel headers 0 and 1
+    - net/mlx5: DR, Add support for matching on geneve_tlv_option_0_exist field
+    - net/mlx5: DR, Improve steering for empty or RX/TX-only matchers
+    - net/mlx5: DR, Ignore modify TTL if device doesn't support it
+    - net/mlx5: Set SMFS as a default steering mode if device supports it
+    - net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
+    - net/mlx5: DR, Add support for matching on Internet Header Length (IHL)
+    - net/mlx5: DR, Remove unneeded comments
+    - net/mlx5: DR, Fix handling of different actions on the same STE in STEv1
+    - net/mlx5: DR, Rename action modify fields to reflect naming in HW spec
+    - net/mlx5: DR, Refactor ste_ctx handling for STE v0/1
+    - net/mlx5: Introduce software defined steering capabilities
+    - net/mlx5: DR, Add support for ConnectX-7 steering
+
+  * alsa: enable the cirrus-logic side-codec to make the speaker output sound
+    (LP: #1965496)
+    - ASoC: cs35l41: CS35L41 Boosted Smart Amplifier
+    - ASoC: cs35l41: Fix use of an uninitialised variable
+    - ASoC: cs35l41: Use regmap_read_poll_timeout to wait for OTP boot
+    - ASoC: cs35l41: Combine adjacent register writes
+    - ASoC: cs35l41: Don't overwrite returned error code
+    - ASoC: cs35l41: Fixup the error messages
+    - ASoC: cs35l41: Fix a bunch of trivial code formating/style issues
+    - misc: cs35l41: Remove unused pdn variable
+    - ASoC: cs35l41: Make cs35l41_remove() return void
+    - ASoC: cs35l41: Change monitor widgets to siggens
+    - ASoC: cs35l41: DSP Support
+    - ASoC: cs35l41: Set the max SPI speed for the whole device
+    - ASoC: cs35l41: Fix link problem
+    - ASoC: cs35l41: Fix undefined reference to core functions
+    - ASoC: cs35l41: Convert tables to shared source code
+    - ASoC: cs35l41: Move cs35l41_otp_unpack to shared code
+    - ASoC: cs35l41: Move power initializations to reg_sequence
+    - ASoC: cs35l41: Create shared function for errata patches
+    - ASoC: cs35l41: Create shared function for setting channels
+    - ASoC: cs35l41: Create shared function for boost configuration
+    - ASoC: cs35l41: Add cs35l51/53 IDs
+    - ASoC: cs35l41: Remove incorrect comment
+    - ASoC: cs35l41: Correct DSP power down
+    - ASoC: cs35l41: Correct handling of some registers in the cache
+    - ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems
+    - ASoC: cs35l41: Update handling of test key registers
+    - ASoC: cs35l41: Add support for hibernate memory retention mode
+    - ALSA: hda: cs35l41: fix double free on error in probe()
+    - ALSA: hda: cs35l41: Avoid overwriting register patch
+    - ALSA: hda: cs35l41: Add calls to newly added test key function
+    - ALSA: hda: cs35l41: Move cs35l41* calls to its own symbol namespace
+    - ALSA: hda: cs35l41: Add missing default cases
+    - ALSA: hda: cs35l41: Make use of the helper function dev_err_probe()
+    - ALSA: hda: cs35l41: Tidyup code
+    - ALSA: hda: cs35l41: Make cs35l41_hda_remove() return void
+    - ALSA: hda/realtek: Add support for Legion 7 16ACHg6 laptop
+    - ALSA: hda/realtek: Add CS35L41 support for Thinkpad laptops
+    - ALSA: hda/realtek: fix speakers and micmute on HP 855 G8
+    - Revert "platform/x86: i2c-multi-instantiate: Don't create platform device
+      for INT3515 ACPI nodes"
+    - spi: Create helper API to lookup ACPI info for spi device
+    - spi: Support selection of the index of the ACPI Spi Resource before alloc
+    - spi: Add API to count spi acpi resources
+    - platform/x86: i2c-multi-instantiate: Rename it for a generic serial driver
+      name
+    - platform/x86: serial-multi-instantiate: Reorganize I2C functions
+    - platform/x86: serial-multi-instantiate: Add SPI support
+    - ALSA: hda/realtek: Add support for HP Laptops
+    - ACPI / scan: Create platform device for CS35L41
+    - [Config] Add cirruslogic side codec support
+
+  * Use kernel-testing repo from launchpad for ADT tests (LP: #1968016)
+    - [Debian] Use kernel-testing repo from launchpad
+
+  * Fix ADL, WD22TB4,Dual monitors display resolution can't reach 4K 60hz
+    (LP: #1967986)
+    - drm/i915/display: Remove check for low voltage sku for max dp source rate
+    - drm/i915/intel_combo_phy: Print I/O voltage info
+
+  * Support different Cirrus audio codec configurations on Dell laptops
+    (LP: #1967988)
+    - ALSA: hda/cs8409: Fix Warlock to use mono mic configuration
+    - ALSA: hda/cs8409: Re-order quirk table into ascending order
+    - ALSA: hda/cs8409: Fix Full Scale Volume setting for all variants
+    - ALSA: hda/cs8409: Support new Warlock MLK Variants
+    - ALSA: hda/cs8409: Disable HSBIAS_SENSE_EN for Cyborg
+    - ALSA: hda/cs8409: Add new Dolphin HW variants
+
+  * Enable speakup kernel modules to allow the speakup screen reader to function
+    (LP: #1967702)
+    - [Config] CONFIG_SPEAKUP=m
+
+  * linux: CONFIG_SERIAL_8250_MID=y (LP: #1967338)
+    - [Config] amd64 CONFIG_SERIAL_8250_MID=y
+
+  * alsa/sdw: Fix the audio issue on a Dell machine without internal mic
+    (LP: #1966841)
+    - ASoC: Intel: soc-acpi: add entries in ADL match table
+
+  * Jammy update: v5.15.34 upstream stable release (LP: #1969107)
+    - Revert "UBUNTU: SAUCE: Revert "scsi: core: Reallocate device's budget map on
+      queue depth change""
+    - lib/logic_iomem: correct fallback config references
+    - um: fix and optimize xor select template for CONFIG64 and timetravel mode
+    - rtc: wm8350: Handle error for wm8350_register_irq
+    - nbd: add error handling support for add_disk()
+    - nbd: Fix incorrect error handle when first_minor is illegal in nbd_dev_add
+    - nbd: Fix hungtask when nbd_config_put
+    - nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
+    - kfence: count unexpectedly skipped allocations
+    - kfence: move saving stack trace of allocations into __kfence_alloc()
+    - kfence: limit currently covered allocations when pool nearly full
+    - KVM: x86/pmu: Use different raw event masks for AMD and Intel
+    - KVM: SVM: Fix kvm_cache_regs.h inclusions for is_guest_mode()
+    - KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
+    - KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
+    - KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
+    - drm: Add orientation quirk for GPD Win Max
+    - ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111
+    - drm/amd/display: Add signal type check when verify stream backends same
+    - drm/amd/amdgpu/amdgpu_cs: fix refcount leak of a dma_fence obj
+    - drm/amd/display: Fix memory leak
+    - drm/amd/display: Use PSR version selected during set_psr_caps
+    - usb: gadget: tegra-xudc: Do not program SPARAM
+    - usb: gadget: tegra-xudc: Fix control endpoint's definitions
+    - usb: cdnsp: fix cdnsp_decode_trb function to properly handle ret value
+    - ptp: replace snprintf with sysfs_emit
+    - drm/amdkfd: Don't take process mutex for svm ioctls
+    - powerpc: dts: t104xrdb: fix phy type for FMAN 4/5
+    - ath11k: fix kernel panic during unload/load ath11k modules
+    - ath11k: pci: fix crash on suspend if board file is not found
+    - ath11k: mhi: use mhi_sync_power_up()
+    - net/smc: Send directly when TCP_CORK is cleared
+    - drm/bridge: Add missing pm_runtime_put_sync
+    - bpf: Make dst_port field in struct bpf_sock 16-bit wide
+    - scsi: mvsas: Replace snprintf() with sysfs_emit()
+    - scsi: bfa: Replace snprintf() with sysfs_emit()
+    - drm/v3d: fix missing unlock
+    - power: supply: axp20x_battery: properly report current when discharging
+    - mt76: mt7921: fix crash when startup fails.
+    - mt76: dma: initialize skip_unmap in mt76_dma_rx_fill
+    - cfg80211: don't add non transmitted BSS to 6GHz scanned channels
+    - libbpf: Fix build issue with llvm-readelf
+    - ipv6: make mc_forwarding atomic
+    - net: initialize init_net earlier
+    - powerpc: Set crashkernel offset to mid of RMA region
+    - drm/amdgpu: Fix recursive locking warning
+    - scsi: smartpqi: Fix kdump issue when controller is locked up
+    - PCI: aardvark: Fix support for MSI interrupts
+    - iommu/arm-smmu-v3: fix event handling soft lockup
+    - usb: ehci: add pci device support for Aspeed platforms
+    - PCI: endpoint: Fix alignment fault error in copy tests
+    - tcp: Don't acquire inet_listen_hashbucket::lock with disabled BH.
+    - PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
+    - scsi: mpi3mr: Fix reporting of actual data transfer size
+    - scsi: mpi3mr: Fix memory leaks
+    - powerpc/set_memory: Avoid spinlock recursion in change_page_attr()
+    - power: supply: axp288-charger: Set Vhold to 4.4V
+    - net/mlx5e: Disable TX queues before registering the netdev
+    - usb: dwc3: pci: Set the swnode from inside dwc3_pci_quirks()
+    - iwlwifi: mvm: Correctly set fragmented EBS
+    - iwlwifi: mvm: move only to an enabled channel
+    - drm/msm/dsi: Remove spurious IRQF_ONESHOT flag
+    - ipv4: Invalidate neighbour for broadcast address upon address addition
+    - dm ioctl: prevent potential spectre v1 gadget
+    - dm: requeue IO if mapping table not yet available
+    - drm/amdkfd: make CRAT table missing message informational only
+    - vfio/pci: Stub vfio_pci_vga_rw when !CONFIG_VFIO_PCI_VGA
+    - scsi: pm8001: Fix pm80xx_pci_mem_copy() interface
+    - scsi: pm8001: Fix pm8001_mpi_task_abort_resp()
+    - scsi: pm8001: Fix task leak in pm8001_send_abort_all()
+    - scsi: pm8001: Fix tag leaks on error
+    - scsi: pm8001: Fix memory leak in pm8001_chip_fw_flash_update_req()
+    - mt76: mt7915: fix injected MPDU transmission to not use HW A-MSDU
+    - powerpc/64s/hash: Make hash faults work in NMI context
+    - mt76: mt7615: Fix assigning negative values to unsigned variable
+    - scsi: aha152x: Fix aha152x_setup() __setup handler return value
+    - scsi: hisi_sas: Free irq vectors in order for v3 HW
+    - scsi: hisi_sas: Limit users changing debugfs BIST count value
+    - net/smc: correct settings of RMB window update limit
+    - mips: ralink: fix a refcount leak in ill_acc_of_setup()
+    - macvtap: advertise link netns via netlink
+    - tuntap: add sanity checks about msg_controllen in sendmsg
+    - Bluetooth: Fix not checking for valid hdev on bt_dev_{info,warn,err,dbg}
+    - Bluetooth: use memset avoid memory leaks
+    - bnxt_en: Eliminate unintended link toggle during FW reset
+    - PCI: endpoint: Fix misused goto label
+    - MIPS: fix fortify panic when copying asm exception handlers
+    - powerpc/64e: Tie PPC_BOOK3E_64 to PPC_FSL_BOOK3E
+    - powerpc/secvar: fix refcount leak in format_show()
+    - scsi: libfc: Fix use after free in fc_exch_abts_resp()
+    - can: isotp: set default value for N_As to 50 micro seconds
+    - can: etas_es58x: es58x_fd_rx_event_msg(): initialize rx_event_msg before
+      calling es58x_check_msg_len()
+    - riscv: Fixed misaligned memory access. Fixed pointer comparison.
+    - net: account alternate interface name memory
+    - net: limit altnames to 64k total
+    - net/mlx5e: Remove overzealous validations in netlink EEPROM query
+    - net: sfp: add 2500base-X quirk for Lantech SFP module
+    - usb: dwc3: omap: fix "unbalanced disables for smps10_out1" on omap5evm
+    - mt76: fix monitor mode crash with sdio driver
+    - xtensa: fix DTC warning unit_address_format
+    - MIPS: ingenic: correct unit node address
+    - Bluetooth: Fix use after free in hci_send_acl
+    - netfilter: conntrack: revisit gc autotuning
+    - netlabel: fix out-of-bounds memory accesses
+    - ceph: fix inode reference leakage in ceph_get_snapdir()
+    - ceph: fix memory leak in ceph_readdir when note_last_dentry returns error
+    - lib/Kconfig.debug: add ARCH dependency for FUNCTION_ALIGN option
+    - init/main.c: return 1 from handled __setup() functions
+    - minix: fix bug when opening a file with O_DIRECT
+    - clk: si5341: fix reported clk_rate when output divider is 2
+    - staging: vchiq_arm: Avoid NULL ptr deref in vchiq_dump_platform_instances
+    - staging: vchiq_core: handle NULL result of find_service_by_handle
+    - phy: amlogic: phy-meson-gxl-usb2: fix shared reset controller use
+    - phy: amlogic: meson8b-usb2: Use dev_err_probe()
+    - phy: amlogic: meson8b-usb2: fix shared reset control use
+    - clk: rockchip: drop CLK_SET_RATE_PARENT from dclk_vop* on rk3568
+    - cpufreq: CPPC: Fix performance/frequency conversion
+    - opp: Expose of-node's name in debugfs
+    - staging: wfx: fix an error handling in wfx_init_common()
+    - w1: w1_therm: fixes w1_seq for ds28ea00 sensors
+    - NFSv4.2: fix reference count leaks in _nfs42_proc_copy_notify()
+    - NFSv4: Protect the state recovery thread against direct reclaim
+    - habanalabs: fix possible memory leak in MMU DR fini
+    - xen: delay xen_hvm_init_time_ops() if kdump is boot on vcpu>=32
+    - clk: ti: Preserve node in ti_dt_clocks_register()
+    - clk: Enforce that disjoints limits are invalid
+    - SUNRPC/call_alloc: async tasks mustn't block waiting for memory
+    - SUNRPC/xprt: async tasks mustn't block waiting for memory
+    - SUNRPC: remove scheduling boost for "SWAPPER" tasks.
+    - NFS: swap IO handling is slightly different for O_DIRECT IO
+    - NFS: swap-out must always use STABLE writes.
+    - x86: Annotate call_on_stack()
+    - x86/Kconfig: Do not allow CONFIG_X86_X32_ABI=y with llvm-objcopy
+    - serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
+    - virtio_console: eliminate anonymous module_init & module_exit
+    - jfs: prevent NULL deref in diFree
+    - SUNRPC: Fix socket waits for write buffer space
+    - NFS: nfsiod should not block forever in mempool_alloc()
+    - NFS: Avoid writeback threads getting stuck in mempool_alloc()
+    - selftests: net: Add tls config dependency for tls selftests
+    - parisc: Fix CPU affinity for Lasi, WAX and Dino chips
+    - parisc: Fix patch code locking and flushing
+    - mm: fix race between MADV_FREE reclaim and blkdev direct IO read
+    - rtc: mc146818-lib: change return values of mc146818_get_time()
+    - rtc: Check return value from mc146818_get_time()
+    - rtc: mc146818-lib: fix RTC presence check
+    - drm/amdgpu: fix off by one in amdgpu_gfx_kiq_acquire()
+    - Drivers: hv: vmbus: Fix potential crash on module unload
+    - Revert "NFSv4: Handle the special Linux file open access mode"
+    - NFSv4: fix open failure with O_ACCMODE flag
+    - scsi: sr: Fix typo in CDROM(CLOSETRAY|EJECT) handling
+    - scsi: core: Fix sbitmap depth in scsi_realloc_sdev_budget_map()
+    - scsi: zorro7xx: Fix a resource leak in zorro7xx_remove_one()
+    - vdpa/mlx5: Rename control VQ workqueue to vdpa wq
+    - vdpa/mlx5: Propagate link status from device to vdpa driver
+    - vdpa: mlx5: prevent cvq work from hogging CPU
+    - net: sfc: add missing xdp queue reinitialization
+    - net/tls: fix slab-out-of-bounds bug in decrypt_internal
+    - vrf: fix packet sniffing for traffic originating from ip tunnels
+    - skbuff: fix coalescing for page_pool fragment recycling
+    - ice: Clear default forwarding VSI during VSI release
+    - mctp: Fix check for dev_hard_header() result
+    - net: ipv4: fix route with nexthop object delete warning
+    - net: stmmac: Fix unset max_speed difference between DT and non-DT platforms
+    - drm/imx: imx-ldb: Check for null pointer after calling kmemdup
+    - drm/imx: Fix memory leak in imx_pd_connector_get_modes
+    - drm/imx: dw_hdmi-imx: Fix bailout in error cases of probe
+    - regulator: rtq2134: Fix missing active_discharge_on setting
+    - regulator: atc260x: Fix missing active_discharge_on setting
+    - arch/arm64: Fix topology initialization for core scheduling
+    - bnxt_en: Synchronize tx when xdp redirects happen on same ring
+    - bnxt_en: reserve space inside receive page for skb_shared_info
+    - bnxt_en: Prevent XDP redirect from running when stopping TX queue
+    - sfc: Do not free an empty page_ring
+    - RDMA/mlx5: Don't remove cache MRs when a delay is needed
+    - RDMA/mlx5: Add a missing update of cache->last_add
+    - IB/cm: Cancel mad on the DREQ event when the state is MRA_REP_RCVD
+    - IB/rdmavt: add lock to call to rvt_error_qp to prevent a race condition
+    - sctp: count singleton chunks in assoc user stats
+    - dpaa2-ptp: Fix refcount leak in dpaa2_ptp_probe
+    - ice: Set txq_teid to ICE_INVAL_TEID on ring creation
+    - ice: Do not skip not enabled queues in ice_vc_dis_qs_msg
+    - ipv6: Fix stats accounting in ip6_pkt_drop
+    - ice: synchronize_rcu() when terminating rings
+    - ice: xsk: fix VSI state check in ice_xsk_wakeup()
+    - net: openvswitch: don't send internal clone attribute to the userspace.
+    - net: ethernet: mv643xx: Fix over zealous checking of_get_mac_address()
+    - net: openvswitch: fix leak of nested actions
+    - rxrpc: fix a race in rxrpc_exit_net()
+    - net: sfc: fix using uninitialized xdp tx_queue
+    - net: phy: mscc-miim: reject clause 45 register accesses
+    - qede: confirm skb is allocated before using
+    - spi: bcm-qspi: fix MSPI only access with bcm_qspi_exec_mem_op()
+    - bpf: Support dual-stack sockets in bpf_tcp_check_syncookie
+    - drbd: Fix five use after free bugs in get_initial_state
+    - scsi: ufs: ufshpb: Fix a NULL check on list iterator
+    - io_uring: nospec index for tags on files update
+    - io_uring: don't touch scm_fp_list after queueing skb
+    - SUNRPC: Handle ENOMEM in call_transmit_status()
+    - SUNRPC: Handle low memory situations in call_status()
+    - SUNRPC: svc_tcp_sendmsg() should handle errors from xdr_alloc_bvec()
+    - iommu/omap: Fix regression in probe for NULL pointer dereference
+    - perf: arm-spe: Fix perf report --mem-mode
+    - perf tools: Fix perf's libperf_print callback
+    - perf session: Remap buf if there is no space for event
+    - arm64: Add part number for Arm Cortex-A78AE
+    - scsi: mpt3sas: Fix use after free in _scsih_expander_node_remove()
+    - scsi: ufs: ufs-pci: Add support for Intel MTL
+    - Revert "mmc: sdhci-xenon: fix annoying 1.8V regulator warning"
+    - mmc: block: Check for errors after write on SPI
+    - mmc: mmci: stm32: correctly check all elements of sg list
+    - mmc: renesas_sdhi: don't overwrite TAP settings when HS400 tuning is
+      complete
+    - mmc: core: Fixup support for writeback-cache for eMMC and SD
+    - lz4: fix LZ4_decompress_safe_partial read out of bound
+    - highmem: fix checks in __kmap_local_sched_{in,out}
+    - mmmremap.c: avoid pointless invalidate_range_start/end on mremap(old_size=0)
+    - mm/mempolicy: fix mpol_new leak in shared_policy_replace
+    - io_uring: don't check req->file in io_fsync_prep()
+    - io_uring: defer splice/tee file validity check until command issue
+    - io_uring: implement compat handling for IORING_REGISTER_IOWQ_AFF
+    - io_uring: fix race between timeout flush and removal
+    - x86/pm: Save the MSR validity status at context setup
+    - x86/speculation: Restore speculation related MSRs during S3 resume
+    - perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
+    - btrfs: fix qgroup reserve overflow the qgroup limit
+    - btrfs: prevent subvol with swapfile from being deleted
+    - spi: core: add dma_map_dev for __spi_unmap_msg()
+    - arm64: patch_text: Fixup last cpu should be master
+    - RDMA/hfi1: Fix use-after-free bug for mm struct
+    - gpio: Restrict usage of GPIO chip irq members before initialization
+    - x86/msi: Fix msi message data shadow struct
+    - x86/mm/tlb: Revert retpoline avoidance approach
+    - perf/x86/intel: Don't extend the pseudo-encoding to GP counters
+    - ata: sata_dwc_460ex: Fix crash due to OOB write
+    - perf: qcom_l2_pmu: fix an incorrect NULL check on list iterator
+    - perf/core: Inherit event_caps
+    - irqchip/gic-v3: Fix GICR_CTLR.RWP polling
+    - fbdev: Fix unregistering of framebuffers without device
+    - amd/display: set backlight only if required
+    - SUNRPC: Prevent immediate close+reconnect
+    - drm/panel: ili9341: fix optional regulator handling
+    - drm/amdgpu/display: change pipe policy for DCN 2.1
+    - drm/amdgpu/smu10: fix SoC/fclk units in auto mode
+    - drm/amdgpu/vcn: Fix the register setting for vcn1
+    - drm/nouveau/pmu: Add missing callbacks for Tegra devices
+    - drm/amdkfd: Create file descriptor after client is added to smi_clients list
+    - drm/amdgpu: don't use BACO for reset in S3
+    - KVM: SVM: Allow AVIC support on system w/ physical APIC ID > 255
+    - net/smc: send directly on setting TCP_NODELAY
+    - Revert "selftests: net: Add tls config dependency for tls selftests"
+    - bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
+    - selftests/bpf: Fix u8 narrow load checks for bpf_sk_lookup remote_port
+    - rtc: mc146818-lib: fix signedness bug in mc146818_get_time()
+    - SUNRPC: Don't call connect() more than once on a TCP socket
+    - Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"
+    - perf build: Don't use -ffat-lto-objects in the python feature test when
+      building with clang-13
+    - perf python: Fix probing for some clang command line options
+    - tools build: Filter out options and warnings not supported by clang
+    - tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
+    - dmaengine: Revert "dmaengine: shdma: Fix runtime PM imbalance on error"
+    - KVM: avoid NULL pointer dereference in kvm_dirty_ring_push
+    - Revert "net/mlx5: Accept devlink user input after driver initialization
+      complete"
+    - ubsan: remove CONFIG_UBSAN_OBJECT_SIZE
+    - selftests: cgroup: Make cg_create() use 0755 for permission instead of 0644
+    - selftests: cgroup: Test open-time credential usage for migration checks
+    - selftests: cgroup: Test open-time cgroup namespace usage for migration
+      checks
+    - mm: don't skip swap entry even if zap_details specified
+    - Drivers: hv: vmbus: Replace smp_store_mb() with virt_store_mb()
+    - x86/bug: Prevent shadowing in __WARN_FLAGS
+    - sched: Teach the forced-newidle balancer about CPU affinity limitation.
+    - x86,static_call: Fix __static_call_return0 for i386
+    - irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
+    - powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
+    - irqchip/gic, gic-v3: Prevent GSI to SGI translations
+    - mm/sparsemem: fix 'mem_section' will never be NULL gcc 12 warning
+    - static_call: Don't make __static_call_return0 static
+    - powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
+    - stacktrace: move filter_irq_stacks() to kernel/stacktrace.c
+    - Linux 5.15.34
+    - [Config] armhf, s390x: update annotations following
+      DEBUG_FORCE_FUNCTION_ALIGN_64B support removal in v5.15.34
+
+  * Jammy update: v5.15.33 upstream stable release (LP: #1969110)
+    - Revert "swiotlb: rework "fix info leak with DMA_FROM_DEVICE""
+    - USB: serial: pl2303: add IBM device IDs
+    - dt-bindings: usb: hcd: correct usb-device path
+    - USB: serial: pl2303: fix GS type detection
+    - USB: serial: simple: add Nokia phone driver
+    - mm: kfence: fix missing objcg housekeeping for SLAB
+    - hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
+    - HID: logitech-dj: add new lightspeed receiver id
+    - HID: Add support for open wheel and no attachment to T300
+    - xfrm: fix tunnel model fragmentation behavior
+    - ARM: mstar: Select HAVE_ARM_ARCH_TIMER
+    - virtio_console: break out of buf poll on remove
+    - vdpa/mlx5: should verify CTRL_VQ feature exists for MQ
+    - tools/virtio: fix virtio_test execution
+    - ethernet: sun: Free the coherent when failing in probing
+    - gpio: Revert regression in sysfs-gpio (gpiolib.c)
+    - spi: Fix invalid sgs value
+    - net:mcf8390: Use platform_get_irq() to get the interrupt
+    - Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"
+    - spi: Fix erroneous sgs value with min_t()
+    - Input: zinitix - do not report shadow fingers
+    - af_key: add __GFP_ZERO flag for compose_sadb_supported in function
+      pfkey_register
+    - net: dsa: microchip: add spi_device_id tables
+    - selftests: vm: fix clang build error multiple output files
+    - locking/lockdep: Avoid potential access of invalid memory in lock_class
+    - drm/amdgpu: move PX checking into amdgpu_device_ip_early_init
+    - drm/amdgpu: only check for _PR3 on dGPUs
+    - iommu/iova: Improve 32-bit free space estimate
+    - virtio-blk: Use blk_validate_block_size() to validate block size
+    - tpm: fix reference counting for struct tpm_chip
+    - usb: typec: tipd: Forward plug orientation to typec subsystem
+    - USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
+    - xhci: fix garbage USBSTS being logged in some cases
+    - xhci: fix runtime PM imbalance in USB2 resume
+    - xhci: make xhci_handshake timeout for xhci_reset() adjustable
+    - xhci: fix uninitialized string returned by xhci_decode_ctrl_ctx()
+    - mei: me: disable driver on the ign firmware
+    - mei: me: add Alder Lake N device id.
+    - mei: avoid iterator usage outside of list_for_each_entry
+    - bus: mhi: pci_generic: Add mru_default for Quectel EM1xx series
+    - bus: mhi: Fix MHI DMA structure endianness
+    - docs: sphinx/requirements: Limit jinja2<3.1
+    - coresight: Fix TRCCONFIGR.QE sysfs interface
+    - coresight: syscfg: Fix memleak on registration failure in
+      cscfg_create_device
+    - iio: afe: rescale: use s64 for temporary scale calculations
+    - iio: inkern: apply consumer scale on IIO_VAL_INT cases
+    - iio: inkern: apply consumer scale when no channel scale is available
+    - iio: inkern: make a best effort on offset calculation
+    - greybus: svc: fix an error handling bug in gb_svc_hello()
+    - clk: rockchip: re-add rational best approximation algorithm to the
+      fractional divider
+    - clk: uniphier: Fix fixed-rate initialization
+    - cifs: fix handlecache and multiuser
+    - cifs: we do not need a spinlock around the tree access during umount
+    - KEYS: fix length validation in keyctl_pkey_params_get_2()
+    - KEYS: asymmetric: enforce that sig algo matches key algo
+    - KEYS: asymmetric: properly validate hash_algo and encoding
+    - Documentation: add link to stable release candidate tree
+    - Documentation: update stable tree link
+    - firmware: stratix10-svc: add missing callback parameter on RSU
+    - firmware: sysfb: fix platform-device leak in error path
+    - HID: intel-ish-hid: Use dma_alloc_coherent for firmware update
+    - SUNRPC: avoid race between mod_timer() and del_timer_sync()
+    - NFS: NFSv2/v3 clients should never be setting NFS_CAP_XATTR
+    - NFSD: prevent underflow in nfssvc_decode_writeargs()
+    - NFSD: prevent integer overflow on 32 bit systems
+    - f2fs: fix to unlock page correctly in error path of is_alive()
+    - f2fs: quota: fix loop condition at f2fs_quota_sync()
+    - f2fs: fix to do sanity check on .cp_pack_total_block_count
+    - remoteproc: Fix count check in rproc_coredump_write()
+    - mm/mlock: fix two bugs in user_shm_lock()
+    - pinctrl: ingenic: Fix regmap on X series SoCs
+    - pinctrl: samsung: drop pin banks references on error paths
+    - net: bnxt_ptp: fix compilation error
+    - spi: mxic: Fix the transmit path
+    - mtd: rawnand: protect access to rawnand devices while in suspend
+    - can: ems_usb: ems_usb_start_xmit(): fix double dev_kfree_skb() in error path
+    - can: m_can: m_can_tx_handler(): fix use after free of skb
+    - can: usb_8dev: usb_8dev_start_xmit(): fix double dev_kfree_skb() in error
+      path
+    - jffs2: fix use-after-free in jffs2_clear_xattr_subsystem
+    - jffs2: fix memory leak in jffs2_do_mount_fs
+    - jffs2: fix memory leak in jffs2_scan_medium
+    - mm: fs: fix lru_cache_disabled race in bh_lru
+    - mm/pages_alloc.c: don't create ZONE_MOVABLE beyond the end of a node
+    - mm: invalidate hwpoison page cache page in fault path
+    - mempolicy: mbind_range() set_policy() after vma_merge()
+    - scsi: core: sd: Add silence_suspend flag to suppress some PM messages
+    - scsi: ufs: Fix runtime PM messages never-ending cycle
+    - scsi: scsi_transport_fc: Fix FPIN Link Integrity statistics counters
+    - scsi: libsas: Fix sas_ata_qc_issue() handling of NCQ NON DATA commands
+    - qed: display VF trust config
+    - qed: validate and restrict untrusted VFs vlan promisc mode
+    - riscv: dts: canaan: Fix SPI3 bus width
+    - riscv: Fix fill_callchain return value
+    - riscv: Increase stack size under KASAN
+    - Revert "Input: clear BTN_RIGHT/MIDDLE on buttonpads"
+    - cifs: prevent bad output lengths in smb2_ioctl_query_info()
+    - cifs: fix NULL ptr dereference in smb2_ioctl_query_info()
+    - ALSA: cs4236: fix an incorrect NULL check on list iterator
+    - ALSA: hda: Avoid unsol event during RPM suspending
+    - ALSA: pcm: Fix potential AB/BA lock with buffer_mutex and mmap_lock
+    - ALSA: hda/realtek: Fix audio regression on Mi Notebook Pro 2020
+    - rtc: mc146818-lib: fix locking in mc146818_set_time
+    - rtc: pl031: fix rtc features null pointer dereference
+    - ocfs2: fix crash when mount with quota enabled
+    - drm/simpledrm: Add "panel orientation" property on non-upright mounted LCD
+      panels
+    - mm: madvise: skip unmapped vma holes passed to process_madvise
+    - mm: madvise: return correct bytes advised with process_madvise
+    - Revert "mm: madvise: skip unmapped vma holes passed to process_madvise"
+    - mm,hwpoison: unmap poisoned page before invalidation
+    - mm/kmemleak: reset tag when compare object pointer
+    - dm stats: fix too short end duration_ns when using precise_timestamps
+    - dm: fix use-after-free in dm_cleanup_zoned_dev()
+    - dm: interlock pending dm_io and dm_wait_for_bios_completion
+    - dm: fix double accounting of flush with data
+    - dm integrity: set journal entry unused when shrinking device
+    - tracing: Have trace event string test handle zero length strings
+    - drbd: fix potential silent data corruption
+    - powerpc/kvm: Fix kvm_use_magic_page
+    - PCI: fu740: Force 2.5GT/s for initial device probe
+    - arm64: signal: nofpsimd: Do not allocate fp/simd context when not available
+    - arm64: Do not defer reserve_crashkernel() for platforms with no DMA memory
+      zones
+    - arm64: dts: qcom: sm8250: Fix MSI IRQ for PCIe1 and PCIe2
+    - arm64: dts: ti: k3-am65: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-j721e: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-j7200: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-am64: Fix gic-v3 compatible regs
+    - ASoC: SOF: Intel: Fix NULL ptr dereference when ENOMEM
+    - Revert "ACPI: Pass the same capabilities to the _OSC regardless of the query
+      flag"
+    - ACPI: properties: Consistently return -ENOENT if there are no more
+      references
+    - coredump: Also dump first pages of non-executable ELF libraries
+    - ext4: fix ext4_fc_stats trace point
+    - ext4: fix fs corruption when tring to remove a non-empty directory with IO
+      error
+    - ext4: make mb_optimize_scan performance mount option work with extents
+    - drivers: hamradio: 6pack: fix UAF bug caused by mod_timer()
+    - samples/landlock: Fix path_list memory leak
+    - landlock: Use square brackets around "landlock-ruleset"
+    - mailbox: tegra-hsp: Flush whole channel
+    - block: limit request dispatch loop duration
+    - block: don't merge across cgroup boundaries if blkcg is enabled
+    - drm/edid: check basic audio support on CEA extension block
+    - fbdev: Hot-unplug firmware fb devices on forced removal
+    - video: fbdev: sm712fb: Fix crash in smtcfb_read()
+    - video: fbdev: atari: Atari 2 bpp (STe) palette bugfix
+    - rfkill: make new event layout opt-in
+    - ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
+    - ARM: dts: at91: sama5d2: Fix PMERRLOC resource size
+    - ARM: dts: exynos: fix UART3 pins configuration in Exynos5250
+    - ARM: dts: exynos: add missing HDMI supplies on SMDK5250
+    - ARM: dts: exynos: add missing HDMI supplies on SMDK5420
+    - mgag200 fix memmapsl configuration in GCTL6 register
+    - carl9170: fix missing bit-wise or operator for tx_params
+    - pstore: Don't use semaphores in always-atomic-context code
+    - thermal: int340x: Increase bitmap size
+    - lib/raid6/test: fix multiple definition linking error
+    - exec: Force single empty string when argv is empty
+    - crypto: rsa-pkcs1pad - only allow with rsa
+    - crypto: rsa-pkcs1pad - correctly get hash from source scatterlist
+    - crypto: rsa-pkcs1pad - restore signature length check
+    - crypto: rsa-pkcs1pad - fix buffer overread in pkcs1pad_verify_complete()
+    - bcache: fixup multiple threads crash
+    - PM: domains: Fix sleep-in-atomic bug caused by genpd_debug_remove()
+    - DEC: Limit PMAX memory probing to R3k systems
+    - media: gpio-ir-tx: fix transmit with long spaces on Orange Pi PC
+    - media: venus: hfi_cmds: List HDR10 property as unsupported for v1 and v3
+    - media: venus: venc: Fix h264 8x8 transform control
+    - media: davinci: vpif: fix unbalanced runtime PM get
+    - media: davinci: vpif: fix unbalanced runtime PM enable
+    - btrfs: zoned: mark relocation as writing
+    - btrfs: extend locking to all space_info members accesses
+    - btrfs: verify the tranisd of the to-be-written dirty extent buffer
+    - xtensa: define update_mmu_tlb function
+    - xtensa: fix stop_machine_cpuslocked call in patch_text
+    - xtensa: fix xtensa_wsr always writing 0
+    - drm/syncobj: flatten dma_fence_chains on transfer
+    - drm/nouveau/backlight: Fix LVDS backlight detection on some laptops
+    - drm/nouveau/backlight: Just set all backlight types as RAW
+    - drm/fb-helper: Mark screen buffers in system memory with FBINFO_VIRTFB
+    - brcmfmac: firmware: Allocate space for default boardrev in nvram
+    - brcmfmac: pcie: Release firmwares in the brcmf_pcie_setup error path
+    - brcmfmac: pcie: Declare missing firmware files in pcie.c
+    - brcmfmac: pcie: Replace brcmf_pcie_copy_mem_todev with memcpy_toio
+    - brcmfmac: pcie: Fix crashes due to early IRQs
+    - drm/i915/opregion: check port number bounds for SWSCI display power state
+    - drm/i915/gem: add missing boundary check in vm_access
+    - PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
+    - PCI: pciehp: Clear cmd_busy bit in polling mode
+    - PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
+    - regulator: qcom_smd: fix for_each_child.cocci warnings
+    - selinux: access superblock_security_struct in LSM blob way
+    - selinux: check return value of sel_make_avc_files
+    - crypto: ccp - Ensure psp_ret is always init'd in
+      __sev_platform_init_locked()
+    - hwrng: cavium - Check health status while reading random data
+    - hwrng: cavium - HW_RANDOM_CAVIUM should depend on ARCH_THUNDER
+    - crypto: sun8i-ss - really disable hash on A80
+    - crypto: authenc - Fix sleep in atomic context in decrypt_tail
+    - crypto: mxs-dcp - Fix scatterlist processing
+    - selinux: Fix selinux_sb_mnt_opts_compat()
+    - thermal: int340x: Check for NULL after calling kmemdup()
+    - crypto: octeontx2 - remove CONFIG_DM_CRYPT check
+    - spi: tegra114: Add missing IRQ check in tegra_spi_probe
+    - spi: tegra210-quad: Fix missin IRQ check in tegra_qspi_probe
+    - stack: Constrain and fix stack offset randomization with Clang builds
+    - arm64/mm: avoid fixmap race condition when create pud mapping
+    - blk-cgroup: set blkg iostat after percpu stat aggregation
+    - selftests/x86: Add validity check and allow field splitting
+    - selftests/sgx: Treat CC as one argument
+    - crypto: rockchip - ECB does not need IV
+    - audit: log AUDIT_TIME_* records only from rules
+    - EVM: fix the evm= __setup handler return value
+    - crypto: ccree - don't attempt 0 len DMA mappings
+    - crypto: hisilicon/sec - fix the aead software fallback for engine
+    - spi: pxa2xx-pci: Balance reference count for PCI DMA device
+    - hwmon: (pmbus) Add mutex to regulator ops
+    - hwmon: (sch56xx-common) Replace WDOG_ACTIVE with WDOG_HW_RUNNING
+    - nvme: cleanup __nvme_check_ids
+    - nvme: fix the check for duplicate unique identifiers
+    - block: don't delete queue kobject before its children
+    - PM: hibernate: fix __setup handler error handling
+    - PM: suspend: fix return value of __setup handler
+    - spi: spi-zynqmp-gqspi: Handle error for dma_set_mask
+    - hwrng: atmel - disable trng on failure path
+    - crypto: sun8i-ss - call finalize with bh disabled
+    - crypto: sun8i-ce - call finalize with bh disabled
+    - crypto: amlogic - call finalize with bh disabled
+    - crypto: gemini - call finalize with bh disabled
+    - crypto: vmx - add missing dependencies
+    - clocksource/drivers/timer-ti-dm: Fix regression from errata i940 fix
+    - clocksource/drivers/exynos_mct: Refactor resources allocation
+    - clocksource/drivers/exynos_mct: Handle DTS with higher number of interrupts
+    - clocksource/drivers/timer-microchip-pit64b: Use notrace
+    - clocksource/drivers/timer-of: Check return value of of_iomap in
+      timer_of_base_init()
+    - arm64: prevent instrumentation of bp hardening callbacks
+    - KEYS: trusted: Fix trusted key backends when building as module
+    - KEYS: trusted: Avoid calling null function trusted_key_exit
+    - ACPI: APEI: fix return value of __setup handlers
+    - crypto: ccp - ccp_dmaengine_unregister release dma channels
+    - crypto: ccree - Fix use after free in cc_cipher_exit()
+    - hwrng: nomadik - Change clk_disable to clk_disable_unprepare
+    - hwmon: (pmbus) Add Vin unit off handling
+    - clocksource: acpi_pm: fix return value of __setup handler
+    - io_uring: don't check unrelated req->open.how in accept request
+    - io_uring: terminate manual loop iterator loop correctly for non-vecs
+    - watch_queue: Fix NULL dereference in error cleanup
+    - watch_queue: Actually free the watch
+    - f2fs: fix to enable ATGC correctly via gc_idle sysfs interface
+    - sched/debug: Remove mpol_get/put and task_lock/unlock from sched_show_numa
+    - sched/core: Export pelt_thermal_tp
+    - sched/uclamp: Fix iowait boost escaping uclamp restriction
+    - rseq: Remove broken uapi field layout on 32-bit little endian
+    - perf/core: Fix address filter parser for multiple filters
+    - perf/x86/intel/pt: Fix address filter config for 32-bit kernel
+    - sched/fair: Improve consistency of allowed NUMA balance calculations
+    - f2fs: fix missing free nid in f2fs_handle_failed_inode
+    - nfsd: more robust allocation failure handling in nfsd_file_cache_init
+    - sched/cpuacct: Fix charge percpu cpuusage
+    - sched/rt: Plug rt_mutex_setprio() vs push_rt_task() race
+    - f2fs: fix to avoid potential deadlock
+    - btrfs: fix unexpected error path when reflinking an inline extent
+    - f2fs: fix compressed file start atomic write may cause data corruption
+    - selftests, x86: fix how check_cc.sh is being invoked
+    - drivers/base/memory: add memory block to memory group after registration
+      succeeded
+    - kunit: make kunit_test_timeout compatible with comment
+    - pinctrl: samsung: Remove EINT handler for Exynos850 ALIVE and CMGP gpios
+    - media: staging: media: zoran: fix usage of vb2_dma_contig_set_max_seg_size
+    - media: camss: csid-170: fix non-10bit formats
+    - media: camss: csid-170: don't enable unused irqs
+    - media: camss: csid-170: set the right HALT_CMD when disabled
+    - media: camss: vfe-170: fix "VFE halt timeout" error
+    - media: staging: media: imx: imx7-mipi-csis: Make subdev name unique
+    - media: v4l2-mem2mem: Apply DST_QUEUE_OFF_BASE on MMAP buffers across ioctls
+    - media: mtk-vcodec: potential dereference of null pointer
+    - media: imx: imx8mq-mipi-csi2: remove wrong irq config write operation
+    - media: imx: imx8mq-mipi_csi2: fix system resume
+    - media: bttv: fix WARNING regression on tunerless devices
+    - media: atmel: atmel-sama7g5-isc: fix ispck leftover
+    - ASoC: sh: rz-ssi: Drop calling rz_ssi_pio_recv() recursively
+    - ASoC: codecs: Check for error pointer after calling devm_regmap_init_mmio
+    - ASoC: xilinx: xlnx_formatter_pcm: Handle sysclk setting
+    - ASoC: simple-card-utils: Set sysclk on all components
+    - media: coda: Fix missing put_device() call in coda_get_vdoa_data
+    - media: meson: vdec: potential dereference of null pointer
+    - media: hantro: Fix overfill bottom register field name
+    - media: ov6650: Fix set format try processing path
+    - media: v4l: Avoid unaligned access warnings when printing 4cc modifiers
+    - media: ov5648: Don't pack controls struct
+    - media: aspeed: Correct value for h-total-pixels
+    - video: fbdev: matroxfb: set maxvram of vbG200eW to the same as vbG200 to
+      avoid black screen
+    - video: fbdev: controlfb: Fix COMPILE_TEST build
+    - video: fbdev: smscufx: Fix null-ptr-deref in ufx_usb_probe()
+    - video: fbdev: atmel_lcdfb: fix an error code in atmel_lcdfb_probe()
+    - video: fbdev: fbcvt.c: fix printing in fb_cvt_print_name()
+    - ARM: dts: Fix OpenBMC flash layout label addresses
+    - firmware: qcom: scm: Remove reassignment to desc following initializer
+    - ARM: dts: qcom: ipq4019: fix sleep clock
+    - soc: qcom: rpmpd: Check for null return of devm_kcalloc
+    - soc: qcom: ocmem: Fix missing put_device() call in of_get_ocmem
+    - soc: qcom: aoss: remove spurious IRQF_ONESHOT flags
+    - arm64: dts: qcom: sdm845: fix microphone bias properties and values
+    - arm64: dts: qcom: sm8250: fix PCIe bindings to follow schema
+    - arm64: dts: broadcom: bcm4908: use proper TWD binding
+    - arm64: dts: qcom: sm8150: Correct TCS configuration for apps rsc
+    - arm64: dts: qcom: sm8350: Correct TCS configuration for apps rsc
+    - firmware: ti_sci: Fix compilation failure when CONFIG_TI_SCI_PROTOCOL is not
+      defined
+    - soc: ti: wkup_m3_ipc: Fix IRQ check in wkup_m3_ipc_probe
+    - ARM: dts: sun8i: v3s: Move the csi1 block to follow address order
+    - vsprintf: Fix potential unaligned access
+    - ARM: dts: imx: Add missing LVDS decoder on M53Menlo
+    - media: mexon-ge2d: fixup frames size in registers
+    - media: video/hdmi: handle short reads of hdmi info frame.
+    - media: ti-vpe: cal: Fix a NULL pointer dereference in
+      cal_ctx_v4l2_init_formats()
+    - media: em28xx: initialize refcount before kref_get
+    - media: usb: go7007: s2250-board: fix leak in probe()
+    - media: cedrus: H265: Fix neighbour info buffer size
+    - media: cedrus: h264: Fix neighbour info buffer size
+    - ASoC: codecs: rx-macro: fix accessing compander for aux
+    - ASoC: codecs: rx-macro: fix accessing array out of bounds for enum type
+    - ASoC: codecs: va-macro: fix accessing array out of bounds for enum type
+    - ASoC: codecs: wc938x: fix accessing array out of bounds for enum type
+    - ASoC: codecs: wcd938x: fix kcontrol max values
+    - ASoC: codecs: wcd934x: fix kcontrol max values
+    - ASoC: codecs: wcd934x: fix return value of wcd934x_rx_hph_mode_put
+    - media: v4l2-core: Initialize h264 scaling matrix
+    - media: ov5640: Fix set format, v4l2_mbus_pixelcode not updated
+    - selftests/lkdtm: Add UBSAN config
+    - lib: uninline simple_strntoull() as well
+    - vsprintf: Fix %pK with kptr_restrict == 0
+    - uaccess: fix nios2 and microblaze get_user_8()
+    - ASoC: rt5663: check the return value of devm_kzalloc() in rt5663_parse_dp()
+    - soc: mediatek: pm-domains: Add wakeup capacity support in power domain
+    - mmc: sdhci_am654: Fix the driver data of AM64 SoC
+    - ASoC: ti: davinci-i2s: Add check for clk_enable()
+    - ALSA: spi: Add check for clk_enable()
+    - arm64: dts: ns2: Fix spi-cpol and spi-cpha property
+    - arm64: dts: broadcom: Fix sata nodename
+    - printk: fix return value of printk.devkmsg __setup handler
+    - ASoC: mxs-saif: Handle errors for clk_enable
+    - ASoC: atmel_ssc_dai: Handle errors for clk_enable
+    - ASoC: dwc-i2s: Handle errors for clk_enable
+    - ASoC: soc-compress: prevent the potentially use of null pointer
+    - memory: emif: Add check for setup_interrupts
+    - memory: emif: check the pointer temp in get_device_details()
+    - ALSA: firewire-lib: fix uninitialized flag for AV/C deferred transaction
+    - arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
+    - m68k: coldfire/device.c: only build for MCF_EDMA when h/w macros are defined
+    - media: stk1160: If start stream fails, return buffers with
+      VB2_BUF_STATE_QUEUED
+    - media: vidtv: Check for null return of vzalloc
+    - ASoC: atmel: Add missing of_node_put() in at91sam9g20ek_audio_probe
+    - ASoC: wm8350: Handle error for wm8350_register_irq
+    - ASoC: fsi: Add check for clk_enable
+    - video: fbdev: omapfb: Add missing of_node_put() in dvic_probe_of
+    - media: saa7134: fix incorrect use to determine if list is empty
+    - ivtv: fix incorrect device_caps for ivtvfb
+    - ASoC: atmel: Fix error handling in snd_proto_probe
+    - ASoC: rockchip: i2s: Fix missing clk_disable_unprepare() in
+      rockchip_i2s_probe
+    - ASoC: SOF: Add missing of_node_put() in imx8m_probe
+    - ASoC: mediatek: use of_device_get_match_data()
+    - ASoC: mediatek: mt8192-mt6359: Fix error handling in mt8192_mt6359_dev_probe
+    - ASoC: rk817: Fix missing clk_disable_unprepare() in rk817_platform_probe
+    - ASoC: dmaengine: do not use a NULL prepare_slave_config() callback
+    - ASoC: mxs: Fix error handling in mxs_sgtl5000_probe
+    - ASoC: fsl_spdif: Disable TX clock when stop
+    - ASoC: imx-es8328: Fix error return code in imx_es8328_probe()
+    - ASoC: SOF: Intel: enable DMI L1 for playback streams
+    - ASoC: msm8916-wcd-digital: Fix missing clk_disable_unprepare() in
+      msm8916_wcd_digital_probe
+    - mmc: davinci_mmc: Handle error for clk_enable
+    - ASoC: atmel: Fix error handling in sam9x5_wm8731_driver_probe
+    - ASoC: msm8916-wcd-analog: Fix error handling in pm8916_wcd_analog_spmi_probe
+    - ASoC: codecs: wcd934x: Add missing of_node_put() in wcd934x_codec_parse_data
+    - ASoC: amd: Fix reference to PCM buffer address
+    - ARM: configs: multi_v5_defconfig: re-enable CONFIG_V4L_PLATFORM_DRIVERS
+    - ARM: configs: multi_v5_defconfig: re-enable DRM_PANEL and FB_xxx
+    - drm/meson: osd_afbcd: Add an exit callback to struct meson_afbcd_ops
+    - drm/meson: Make use of the helper function
+      devm_platform_ioremap_resourcexxx()
+    - drm/meson: split out encoder from meson_dw_hdmi
+    - drm/meson: Fix error handling when afbcd.ops->init fails
+    - drm/bridge: Fix free wrong object in sii8620_init_rcp_input_dev
+    - drm/bridge: Add missing pm_runtime_disable() in __dw_mipi_dsi_probe
+    - drm/bridge: nwl-dsi: Fix PM disable depth imbalance in nwl_dsi_probe
+    - drm: bridge: adv7511: Fix ADV7535 HPD enablement
+    - ath10k: fix memory overwrite of the WoWLAN wakeup packet pattern
+    - drm/v3d/v3d_drv: Check for error num after setting mask
+    - drm/panfrost: Check for error num after setting mask
+    - libbpf: Fix possible NULL pointer dereference when destroying skeleton
+    - bpftool: Only set obj->skeleton on complete success
+    - udmabuf: validate ubuf->pagecount
+    - bpf: Fix UAF due to race between btf_try_get_module and load_module
+    - drm/selftests/test-drm_dp_mst_helper: Fix memory leak in
+      sideband_msg_req_encode_decode
+    - selftests: bpf: Fix bind on used port
+    - Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
+    - Bluetooth: hci_serdev: call init_rwsem() before p->open()
+    - mtd: onenand: Check for error irq
+    - mtd: rawnand: gpmi: fix controller timings setting
+    - drm/edid: Don't clear formats if using deep color
+    - drm/edid: Split deep color modes between RGB and YUV444
+    - ionic: fix type complaint in ionic_dev_cmd_clean()
+    - ionic: start watchdog after all is setup
+    - ionic: Don't send reset commands if FW isn't running
+    - drm/nouveau/acr: Fix undefined behavior in nvkm_acr_hsfw_load_bl()
+    - drm/amd/display: Fix a NULL pointer dereference in
+      amdgpu_dm_connector_add_common_modes()
+    - drm/amd/pm: return -ENOTSUPP if there is no get_dpm_ultimate_freq function
+    - net: phy: at803x: move page selection fix to config_init
+    - selftests/bpf: Normalize XDP section names in selftests
+    - selftests/bpf/test_xdp_redirect_multi: use temp netns for testing
+    - ath9k_htc: fix uninit value bugs
+    - RDMA/core: Set MR type in ib_reg_user_mr
+    - KVM: PPC: Fix vmx/vsx mixup in mmio emulation
+    - selftests/net: timestamping: Fix bind_phc check
+    - i40e: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - i40e: respect metadata on XSK Rx to skb
+    - igc: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - ixgbe: pass bi->xdp to ixgbe_construct_skb_zc() directly
+    - ixgbe: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - ixgbe: respect metadata on XSK Rx to skb
+    - power: reset: gemini-poweroff: Fix IRQ check in gemini_poweroff_probe
+    - ray_cs: Check ioremap return value
+    - powerpc: dts: t1040rdb: fix ports names for Seville Ethernet switch
+    - KVM: PPC: Book3S HV: Check return value of kvmppc_radix_init
+    - powerpc/perf: Don't use perf_hw_context for trace IMC PMU
+    - mt76: connac: fix sta_rec_wtbl tag len
+    - mt76: mt7915: use proper aid value in mt7915_mcu_wtbl_generic_tlv in sta
+      mode
+    - mt76: mt7915: use proper aid value in mt7915_mcu_sta_basic_tlv
+    - mt76: mt7921: fix a leftover race in runtime-pm
+    - mt76: mt7615: fix a leftover race in runtime-pm
+    - mt76: mt7603: check sta_rates pointer in mt7603_sta_rate_tbl_update
+    - mt76: mt7615: check sta_rates pointer in mt7615_sta_rate_tbl_update
+    - ptp: unregister virtual clocks when unregistering physical clock.
+    - net: dsa: mv88e6xxx: Enable port policy support on 6097
+    - mac80211: Remove a couple of obsolete TODO
+    - mac80211: limit bandwidth in HE capabilities
+    - scripts/dtc: Call pkg-config POSIXly correct
+    - livepatch: Fix build failure on 32 bits processors
+    - net: asix: add proper error handling of usb read errors
+    - i2c: bcm2835: Use platform_get_irq() to get the interrupt
+    - i2c: bcm2835: Fix the error handling in 'bcm2835_i2c_probe()'
+    - mtd: mchp23k256: Add SPI ID table
+    - mtd: mchp48l640: Add SPI ID table
+    - igc: avoid kernel warning when changing RX ring parameters
+    - igb: refactor XDP registration
+    - PCI: aardvark: Fix reading MSI interrupt number
+    - PCI: aardvark: Fix reading PCI_EXP_RTSTA_PME bit on emulated bridge
+    - RDMA/rxe: Check the last packet by RXE_END_MASK
+    - libbpf: Fix signedness bug in btf_dump_array_data()
+    - cxl/core: Fix cxl_probe_component_regs() error message
+    - cxl/regs: Fix size of CXL Capability Header Register
+    - net:enetc: allocate CBD ring data memory using DMA coherent methods
+    - libbpf: Fix compilation warning due to mismatched printf format
+    - drm/bridge: dw-hdmi: use safe format when first in bridge chain
+    - libbpf: Use dynamically allocated buffer when receiving netlink messages
+    - power: supply: ab8500: Fix memory leak in ab8500_fg_sysfs_init
+    - HID: i2c-hid: fix GET/SET_REPORT for unnumbered reports
+    - iommu/ipmmu-vmsa: Check for error num after setting mask
+    - drm/bridge: anx7625: Fix overflow issue on reading EDID
+    - bpftool: Fix the error when lookup in no-btf maps
+    - drm/amd/pm: enable pm sysfs write for one VF mode
+    - drm/amd/display: Add affected crtcs to atomic state for dsc mst unplug
+    - libbpf: Fix memleak in libbpf_netlink_recv()
+    - IB/cma: Allow XRC INI QPs to set their local ACK timeout
+    - dax: make sure inodes are flushed before destroy cache
+    - selftests: mptcp: add csum mib check for mptcp_connect
+    - iwlwifi: mvm: Don't call iwl_mvm_sta_from_mac80211() with NULL sta
+    - iwlwifi: mvm: don't iterate unadded vifs when handling FW SMPS req
+    - iwlwifi: mvm: align locking in D3 test debugfs
+    - iwlwifi: yoyo: remove DBGI_SRAM address reset writing
+    - iwlwifi: Fix -EIO error code that is never returned
+    - iwlwifi: mvm: Fix an error code in iwl_mvm_up()
+    - mtd: rawnand: pl353: Set the nand chip node as the flash node
+    - drm/msm/dp: populate connector of struct dp_panel
+    - drm/msm/dp: stop link training after link training 2 failed
+    - drm/msm/dp: always add fail-safe mode into connector mode list
+    - drm/msm/dsi: Use "ref" fw clock instead of global name for VCO parent
+    - drm/msm/dsi/phy: fix 7nm v4.0 settings for C-PHY mode
+    - drm/msm/dpu: add DSPP blocks teardown
+    - drm/msm/dpu: fix dp audio condition
+    - dm crypt: fix get_key_size compiler warning if !CONFIG_KEYS
+    - vfio/pci: fix memory leak during D3hot to D0 transition
+    - vfio/pci: wake-up devices around reset functions
+    - scsi: fnic: Fix a tracing statement
+    - scsi: pm8001: Fix command initialization in pm80XX_send_read_log()
+    - scsi: pm8001: Fix command initialization in pm8001_chip_ssp_tm_req()
+    - scsi: pm8001: Fix payload initialization in pm80xx_set_thermal_config()
+    - scsi: pm8001: Fix le32 values handling in
+      pm80xx_set_sas_protocol_timer_config()
+    - scsi: pm8001: Fix payload initialization in pm80xx_encrypt_update()
+    - scsi: pm8001: Fix le32 values handling in pm80xx_chip_ssp_io_req()
+    - scsi: pm8001: Fix le32 values handling in pm80xx_chip_sata_req()
+    - scsi: pm8001: Fix NCQ NON DATA command task initialization
+    - scsi: pm8001: Fix NCQ NON DATA command completion handling
+    - scsi: pm8001: Fix abort all task initialization
+    - RDMA/mlx5: Fix the flow of a miss in the allocation of a cache ODP MR
+    - drm/amd/display: Remove vupdate_int_entry definition
+    - TOMOYO: fix __setup handlers return values
+    - power: supply: sbs-charger: Don't cancel work that is not initialized
+    - ext2: correct max file size computing
+    - drm/tegra: Fix reference leak in tegra_dsi_ganged_probe
+    - power: supply: bq24190_charger: Fix bq24190_vbus_is_enabled() wrong false
+      return
+    - scsi: hisi_sas: Change permission of parameter prot_mask
+    - drm/bridge: cdns-dsi: Make sure to to create proper aliases for dt
+    - bpf, arm64: Call build_prologue() first in first JIT pass
+    - bpf, arm64: Feed byte-offset into bpf line info
+    - xsk: Fix race at socket teardown
+    - RDMA/irdma: Fix netdev notifications for vlan's
+    - RDMA/irdma: Fix Passthrough mode in VM
+    - RDMA/irdma: Remove incorrect masking of PD
+    - gpu: host1x: Fix a memory leak in 'host1x_remove()'
+    - libbpf: Skip forward declaration when counting duplicated type names
+    - powerpc/mm/numa: skip NUMA_NO_NODE onlining in parse_numa_properties()
+    - powerpc/Makefile: Don't pass -mcpu=powerpc64 when building 32-bit
+    - KVM: x86: Fix emulation in writing cr8
+    - KVM: x86/emulator: Defer not-present segment check in
+      __load_segment_descriptor()
+    - hv_balloon: rate-limit "Unhandled message" warning
+    - i2c: xiic: Make bus names unique
+    - power: supply: wm8350-power: Handle error for wm8350_register_irq
+    - power: supply: wm8350-power: Add missing free in free_charger_irq
+    - IB/hfi1: Allow larger MTU without AIP
+    - RDMA/core: Fix ib_qp_usecnt_dec() called when error
+    - PCI: Reduce warnings on possible RW1C corruption
+    - net: axienet: fix RX ring refill allocation failure handling
+    - drm/msm/a6xx: Fix missing ARRAY_SIZE() check
+    - mips: DEC: honor CONFIG_MIPS_FP_SUPPORT=n
+    - MIPS: Sanitise Cavium switch cases in TLB handler synthesizers
+    - powerpc/sysdev: fix incorrect use to determine if list is empty
+    - powerpc/64s: Don't use DSISR for SLB faults
+    - mfd: mc13xxx: Add check for mc13xxx_irq_request
+    - libbpf: Unmap rings when umem deleted
+    - selftests/bpf: Make test_lwt_ip_encap more stable and faster
+    - platform/x86: huawei-wmi: check the return value of device_create_file()
+    - scsi: mpt3sas: Fix incorrect 4GB boundary check
+    - powerpc: 8xx: fix a return value error in mpc8xx_pic_init
+    - vxcan: enable local echo for sent CAN frames
+    - ath10k: Fix error handling in ath10k_setup_msa_resources
+    - mips: cdmm: Fix refcount leak in mips_cdmm_phys_base
+    - MIPS: RB532: fix return value of __setup handler
+    - MIPS: pgalloc: fix memory leak caused by pgd_free()
+    - mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
+    - power: ab8500_chargalg: Use CLOCK_MONOTONIC
+    - RDMA/irdma: Prevent some integer underflows
+    - Revert "RDMA/core: Fix ib_qp_usecnt_dec() called when error"
+    - RDMA/mlx5: Fix memory leak in error flow for subscribe event routine
+    - bpf, sockmap: Fix memleak in sk_psock_queue_msg
+    - bpf, sockmap: Fix memleak in tcp_bpf_sendmsg while sk msg is full
+    - bpf, sockmap: Fix more uncharged while msg has more_data
+    - bpf, sockmap: Fix double uncharge the mem of sk_msg
+    - samples/bpf, xdpsock: Fix race when running for fix duration of time
+    - USB: storage: ums-realtek: fix error code in rts51x_read_mem()
+    - drm/i915/display: Fix HPD short pulse handling for eDP
+    - netfilter: flowtable: Fix QinQ and pppoe support for inet table
+    - mt76: mt7921: fix mt7921_queues_acq implementation
+    - can: isotp: sanitize CAN ID checks in isotp_bind()
+    - can: isotp: return -EADDRNOTAVAIL when reading from unbound socket
+    - can: isotp: support MSG_TRUNC flag when reading from socket
+    - bareudp: use ipv6_mod_enabled to check if IPv6 enabled
+    - ibmvnic: fix race between xmit and reset
+    - af_unix: Fix some data-races around unix_sk(sk)->oob_skb.
+    - selftests/bpf: Fix error reporting from sock_fields programs
+    - Bluetooth: hci_uart: add missing NULL check in h5_enqueue
+    - Bluetooth: call hci_le_conn_failed with hdev lock in hci_le_conn_failed
+    - Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interrupt
+    - ipv4: Fix route lookups when handling ICMP redirects and PMTU updates
+    - af_netlink: Fix shift out of bounds in group mask calculation
+    - i2c: meson: Fix wrong speed use from probe
+    - netfilter: conntrack: Add and use nf_ct_set_auto_assign_helper_warned()
+    - i2c: mux: demux-pinctrl: do not deactivate a master that is not active
+    - powerpc/pseries: Fix use after free in remove_phb_dynamic()
+    - selftests/bpf/test_lirc_mode2.sh: Exit with proper code
+    - PCI: Avoid broken MSI on SB600 USB devices
+    - net: bcmgenet: Use stronger register read/writes to assure ordering
+    - tcp: ensure PMTU updates are processed during fastopen
+    - openvswitch: always update flow key after nat
+    - net: dsa: fix panic on shutdown if multi-chip tree failed to probe
+    - tipc: fix the timer expires after interval 100ms
+    - mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
+    - ice: fix 'scheduling while atomic' on aux critical err interrupt
+    - ice: don't allow to run ice_send_event_to_aux() in atomic ctx
+    - drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via
+      ethtool
+    - kernel/resource: fix kfree() of bootmem memory again
+    - staging: r8188eu: convert DBG_88E_LEVEL call in hal/rtl8188e_hal_init.c
+    - staging: r8188eu: release_firmware is not called if allocation fails
+    - mxser: fix xmit_buf leak in activate when LSR == 0xff
+    - fsi: scom: Fix error handling
+    - fsi: scom: Remove retries in indirect scoms
+    - pwm: lpc18xx-sct: Initialize driver data and hardware before pwmchip_add()
+    - pps: clients: gpio: Propagate return value from pps_gpio_probe
+    - fsi: Aspeed: Fix a potential double free
+    - misc: alcor_pci: Fix an error handling path
+    - cpufreq: qcom-cpufreq-nvmem: fix reading of PVS Valid fuse
+    - soundwire: intel: fix wrong register name in intel_shim_wake
+    - clk: qcom: ipq8074: fix PCI-E clock oops
+    - dmaengine: idxd: check GENCAP config support for gencfg register
+    - dmaengine: idxd: change bandwidth token to read buffers
+    - dmaengine: idxd: restore traffic class defaults after wq reset
+    - iio: mma8452: Fix probe failing when an i2c_device_id is used
+    - serial: 8250_aspeed_vuart: add PORT_ASPEED_VUART port type
+    - staging:iio:adc:ad7280a: Fix handing of device address bit reversing.
+    - pinctrl: renesas: r8a77470: Reduce size for narrow VIN1 channel
+    - pinctrl: renesas: checker: Fix miscalculation of number of states
+    - clk: qcom: ipq8074: Use floor ops for SDCC1 clock
+    - phy: dphy: Correct lpx parameter and its derivatives(ta_{get,go,sure})
+    - phy: phy-brcm-usb: fixup BCM4908 support
+    - serial: 8250_mid: Balance reference count for PCI DMA device
+    - serial: 8250_lpss: Balance reference count for PCI DMA device
+    - NFS: Use of mapping_set_error() results in spurious errors
+    - serial: 8250: Fix race condition in RTS-after-send handling
+    - iio: adc: Add check for devm_request_threaded_irq
+    - habanalabs: Add check for pci_enable_device
+    - NFS: Return valid errors from nfs2/3_decode_dirent()
+    - staging: r8188eu: fix endless loop in recv_func
+    - dma-debug: fix return value of __setup handlers
+    - clk: imx7d: Remove audio_mclk_root_clk
+    - clk: imx: off by one in imx_lpcg_parse_clks_from_dt()
+    - clk: at91: sama7g5: fix parents of PDMCs' GCLK
+    - clk: qcom: clk-rcg2: Update logic to calculate D value for RCG
+    - clk: qcom: clk-rcg2: Update the frac table for pixel clock
+    - dmaengine: hisi_dma: fix MSI allocate fail when reload hisi_dma
+    - remoteproc: qcom: Fix missing of_node_put in adsp_alloc_memory_region
+    - remoteproc: qcom_wcnss: Add missing of_node_put() in
+      wcnss_alloc_memory_region
+    - remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_region
+    - nvdimm/region: Fix default alignment for small regions
+    - clk: actions: Terminate clk_div_table with sentinel element
+    - clk: loongson1: Terminate clk_div_table with sentinel element
+    - clk: hisilicon: Terminate clk_div_table with sentinel element
+    - clk: clps711x: Terminate clk_div_table with sentinel element
+    - clk: Fix clk_hw_get_clk() when dev is NULL
+    - clk: tegra: tegra124-emc: Fix missing put_device() call in
+      emc_ensure_emc_driver
+    - mailbox: imx: fix crash in resume on i.mx8ulp
+    - NFS: remove unneeded check in decode_devicenotify_args()
+    - staging: mt7621-dts: fix LEDs and pinctrl on GB-PC1 devicetree
+    - staging: mt7621-dts: fix formatting
+    - staging: mt7621-dts: fix pinctrl properties for ethernet
+    - staging: mt7621-dts: fix GB-PC2 devicetree
+    - pinctrl: mediatek: Fix missing of_node_put() in mtk_pctrl_init
+    - pinctrl: mediatek: paris: Fix PIN_CONFIG_BIAS_* readback
+    - pinctrl: mediatek: paris: Fix "argument" argument type for mtk_pinconf_get()
+    - pinctrl: mediatek: paris: Fix pingroup pin config state readback
+    - pinctrl: mediatek: paris: Skip custom extra pin config dump for virtual
+      GPIOs
+    - pinctrl: microchip sgpio: use reset driver
+    - pinctrl: microchip-sgpio: lock RMW access
+    - pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
+    - pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
+    - tty: hvc: fix return value of __setup handler
+    - kgdboc: fix return value of __setup handler
+    - serial: 8250: fix XOFF/XON sending when DMA is used
+    - virt: acrn: obtain pa from VMA with PFNMAP flag
+    - virt: acrn: fix a memory leak in acrn_dev_ioctl()
+    - kgdbts: fix return value of __setup handler
+    - firmware: google: Properly state IOMEM dependency
+    - driver core: dd: fix return value of __setup handler
+    - jfs: fix divide error in dbNextAG
+    - netfilter: nf_conntrack_tcp: preserve liberal flag in tcp options
+    - SUNRPC don't resend a task on an offlined transport
+    - NFSv4.1: don't retry BIND_CONN_TO_SESSION on session error
+    - kdb: Fix the putarea helper function
+    - perf stat: Fix forked applications enablement of counters
+    - clk: qcom: gcc-msm8994: Fix gpll4 width
+    - vsock/virtio: initialize vdev->priv before using VQs
+    - vsock/virtio: read the negotiated features before using VQs
+    - vsock/virtio: enable VQs early on probe
+    - clk: Initialize orphan req_rate
+    - xen: fix is_xen_pmu()
+    - net: enetc: report software timestamping via SO_TIMESTAMPING
+    - net: hns3: fix bug when PF set the duplicate MAC address for VFs
+    - net: hns3: fix port base vlan add fail when concurrent with reset
+    - net: hns3: add vlan list lock to protect vlan list
+    - net: hns3: format the output of the MAC address
+    - net: hns3: refine the process when PF set VF VLAN
+    - net: phy: broadcom: Fix brcm_fet_config_init()
+    - selftests: test_vxlan_under_vrf: Fix broken test case
+    - NFS: Don't loop forever in nfs_do_recoalesce()
+    - net: hns3: clean residual vf config after disable sriov
+    - net: sparx5: depends on PTP_1588_CLOCK_OPTIONAL
+    - qlcnic: dcb: default to returning -EOPNOTSUPP
+    - net/x25: Fix null-ptr-deref caused by x25_disconnect
+    - net: sparx5: switchdev: fix possible NULL pointer dereference
+    - octeontx2-af: initialize action variable
+    - net: prefer nf_ct_put instead of nf_conntrack_put
+    - net/sched: act_ct: fix ref leak when switching zones
+    - NFSv4/pNFS: Fix another issue with a list iterator pointing to the head
+    - net: dsa: bcm_sf2_cfp: fix an incorrect NULL check on list iterator
+    - fs: fd tables have to be multiples of BITS_PER_LONG
+    - lib/test: use after free in register_test_dev_kmod()
+    - fs: fix fd table size alignment properly
+    - LSM: general protection fault in legacy_parse_param
+    - regulator: rpi-panel: Handle I2C errors/timing to the Atmel
+    - crypto: hisilicon/qm - cleanup warning in qm_vf_read_qos
+    - gcc-plugins/stackleak: Exactly match strings instead of prefixes
+    - pinctrl: npcm: Fix broken references to chip->parent_device
+    - rcu: Mark writes to the rcu_segcblist structure's ->flags field
+    - block/bfq_wf2q: correct weight to ioprio
+    - crypto: xts - Add softdep on ecb
+    - crypto: hisilicon/sec - not need to enable sm4 extra mode at HW V3
+    - block, bfq: don't move oom_bfqq
+    - selinux: use correct type for context length
+    - arm64: module: remove (NOLOAD) from linker script
+    - selinux: allow FIOCLEX and FIONCLEX with policy capability
+    - loop: use sysfs_emit() in the sysfs xxx show()
+    - Fix incorrect type in assignment of ipv6 port for audit
+    - irqchip/qcom-pdc: Fix broken locking
+    - irqchip/nvic: Release nvic_base upon failure
+    - fs/binfmt_elf: Fix AT_PHDR for unusual ELF files
+    - bfq: fix use-after-free in bfq_dispatch_request
+    - ACPICA: Avoid walking the ACPI Namespace if it is not there
+    - lib/raid6/test/Makefile: Use $(pound) instead of \# for Make 4.3
+    - Revert "Revert "block, bfq: honor already-setup queue merges""
+    - ACPI/APEI: Limit printable size of BERT table data
+    - PM: core: keep irq flags in device_pm_check_callbacks()
+    - parisc: Fix handling off probe non-access faults
+    - nvme-tcp: lockdep: annotate in-kernel sockets
+    - spi: tegra20: Use of_device_get_match_data()
+    - atomics: Fix atomic64_{read_acquire,set_release} fallbacks
+    - locking/lockdep: Iterate lock_classes directly when reading lockdep files
+    - ext4: correct cluster len and clusters changed accounting in ext4_mb_mark_bb
+    - ext4: fix ext4_mb_mark_bb() with flex_bg with fast_commit
+    - sched/tracing: Report TASK_RTLOCK_WAIT tasks as TASK_UNINTERRUPTIBLE
+    - ext4: don't BUG if someone dirty pages without asking ext4 first
+    - f2fs: fix to do sanity check on curseg->alloc_type
+    - NFSD: Fix nfsd_breaker_owns_lease() return values
+    - f2fs: don't get FREEZE lock in f2fs_evict_inode in frozen fs
+    - btrfs: harden identification of a stale device
+    - btrfs: make search_csum_tree return 0 if we get -EFBIG
+    - f2fs: use spin_lock to avoid hang
+    - f2fs: compress: fix to print raw data size in error path of lz4
+      decompression
+    - Adjust cifssb maximum read size
+    - ntfs: add sanity check on allocation size
+    - media: staging: media: zoran: move videodev alloc
+    - media: staging: media: zoran: calculate the right buffer number for
+      zoran_reap_stat_com
+    - media: staging: media: zoran: fix various V4L2 compliance errors
+    - media: atmel: atmel-isc-base: report frame sizes as full supported range
+    - media: ir_toy: free before error exiting
+    - ASoC: sh: rz-ssi: Make the data structures available before registering the
+      handlers
+    - ASoC: SOF: Intel: match sdw version on link_slaves_found
+    - media: imx-jpeg: Prevent decoding NV12M jpegs into single-planar buffers
+    - media: iommu/mediatek-v1: Free the existed fwspec if the master dev already
+      has
+    - media: iommu/mediatek: Return ENODEV if the device is NULL
+    - media: iommu/mediatek: Add device_link between the consumer and the larb
+      devices
+    - video: fbdev: nvidiafb: Use strscpy() to prevent buffer overflow
+    - video: fbdev: w100fb: Reset global state
+    - video: fbdev: cirrusfb: check pixclock to avoid divide by zero
+    - video: fbdev: omapfb: acx565akm: replace snprintf with sysfs_emit
+    - ARM: dts: qcom: fix gic_irq_domain_translate warnings for msm8960
+    - ARM: dts: bcm2837: Add the missing L1/L2 cache information
+    - ASoC: madera: Add dependencies on MFD
+    - media: atomisp_gmin_platform: Add DMI quirk to not turn AXP ELDO2 regulator
+      off on some boards
+    - media: atomisp: fix dummy_ptr check to avoid duplicate active_bo
+    - ARM: ftrace: avoid redundant loads or clobbering IP
+    - ARM: dts: imx7: Use audio_mclk_post_div instead audio_mclk_root_clk
+    - arm64: defconfig: build imx-sdma as a module
+    - video: fbdev: omapfb: panel-dsi-cm: Use sysfs_emit() instead of snprintf()
+    - video: fbdev: omapfb: panel-tpo-td043mtea1: Use sysfs_emit() instead of
+      snprintf()
+    - video: fbdev: udlfb: replace snprintf in show functions with sysfs_emit
+    - ARM: dts: bcm2711: Add the missing L1/L2 cache information
+    - ASoC: soc-core: skip zero num_dai component in searching dai name
+    - media: imx-jpeg: fix a bug of accessing array out of bounds
+    - media: cx88-mpeg: clear interrupt status register before streaming video
+    - uaccess: fix type mismatch warnings from access_ok()
+    - lib/test_lockup: fix kernel pointer check for separate address spaces
+    - ARM: tegra: tamonten: Fix I2C3 pad setting
+    - ARM: mmp: Fix failure to remove sram device
+    - ASoC: amd: vg: fix for pm resume callback sequence
+    - video: fbdev: sm712fb: Fix crash in smtcfb_write()
+    - media: i2c: ov5648: Fix lockdep error
+    - media: Revert "media: em28xx: add missing em28xx_close_extension"
+    - media: hdpvr: initialize dev->worker at hdpvr_register_videodev
+    - ASoC: Intel: sof_sdw: fix quirks for 2022 HP Spectre x360 13"
+    - tracing: Have TRACE_DEFINE_ENUM affect trace event types as well
+    - mmc: host: Return an error when ->enable_sdio_irq() ops is missing
+    - media: atomisp: fix bad usage at error handling logic
+    - ALSA: hda/realtek: Add alc256-samsung-headphone fixup
+    - KVM: x86: Reinitialize context if host userspace toggles EFER.LME
+    - KVM: x86/mmu: Move "invalid" check out of kvm_tdp_mmu_get_root()
+    - KVM: x86/mmu: Zap _all_ roots when unmapping gfn range in TDP MMU
+    - KVM: x86/mmu: Check for present SPTE when clearing dirty bit in TDP MMU
+    - KVM: x86: hyper-v: Drop redundant 'ex' parameter from kvm_hv_send_ipi()
+    - KVM: x86: hyper-v: Drop redundant 'ex' parameter from kvm_hv_flush_tlb()
+    - KVM: x86: hyper-v: Fix the maximum number of sparse banks for XMM fast TLB
+      flush hypercalls
+    - KVM: x86: hyper-v: HVCALL_SEND_IPI_EX is an XMM fast hypercall
+    - powerpc/kasan: Fix early region not updated correctly
+    - powerpc/lib/sstep: Fix 'sthcx' instruction
+    - powerpc/lib/sstep: Fix build errors with newer binutils
+    - powerpc: Add set_memory_{p/np}() and remove set_memory_attr()
+    - powerpc: Fix build errors with newer binutils
+    - drm/dp: Fix off-by-one in register cache size
+    - drm/i915: Treat SAGV block time 0 as SAGV disabled
+    - drm/i915: Fix PSF GV point mask when SAGV is not possible
+    - drm/i915: Reject unsupported TMDS rates on ICL+
+    - scsi: qla2xxx: Refactor asynchronous command initialization
+    - scsi: qla2xxx: Implement ref count for SRB
+    - scsi: qla2xxx: Fix stuck session in gpdb
+    - scsi: qla2xxx: Fix warning message due to adisc being flushed
+    - scsi: qla2xxx: Fix scheduling while atomic
+    - scsi: qla2xxx: Fix premature hw access after PCI error
+    - scsi: qla2xxx: Fix wrong FDMI data for 64G adapter
+    - scsi: qla2xxx: Fix warning for missing error code
+    - scsi: qla2xxx: Fix device reconnect in loop topology
+    - scsi: qla2xxx: edif: Fix clang warning
+    - scsi: qla2xxx: Fix T10 PI tag escape and IP guard options for 28XX adapters
+    - scsi: qla2xxx: Add devids and conditionals for 28xx
+    - scsi: qla2xxx: Check for firmware dump already collected
+    - scsi: qla2xxx: Suppress a kernel complaint in qla_create_qpair()
+    - scsi: qla2xxx: Fix disk failure to rediscover
+    - scsi: qla2xxx: Fix incorrect reporting of task management failure
+    - scsi: qla2xxx: Fix hang due to session stuck
+    - scsi: qla2xxx: Fix missed DMA unmap for NVMe ls requests
+    - scsi: qla2xxx: Fix N2N inconsistent PLOGI
+    - scsi: qla2xxx: Fix stuck session of PRLI reject
+    - scsi: qla2xxx: Reduce false trigger to login
+    - scsi: qla2xxx: Use correct feature type field during RFF_ID processing
+    - platform: chrome: Split trace include file
+    - KVM: x86: Check lapic_in_kernel() before attempting to set a SynIC irq
+    - KVM: x86: Avoid theoretical NULL pointer dereference in
+      kvm_irq_delivery_to_apic_fast()
+    - KVM: x86: Forbid VMM to set SYNIC/STIMER MSRs when SynIC wasn't activated
+    - KVM: Prevent module exit until all VMs are freed
+    - KVM: x86: fix sending PV IPI
+    - KVM: SVM: fix panic on out-of-bounds guest IRQ
+    - ubifs: rename_whiteout: Fix double free for whiteout_ui->data
+    - ubifs: Fix deadlock in concurrent rename whiteout and inode writeback
+    - ubifs: Add missing iput if do_tmpfile() failed in rename whiteout
+    - ubifs: Rename whiteout atomically
+    - ubifs: Fix 'ui->dirty' race between do_tmpfile() and writeback work
+    - ubifs: Rectify space amount budget for mkdir/tmpfile operations
+    - ubifs: setflags: Make dirtied_ino_d 8 bytes aligned
+    - ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock()
+    - ubifs: Fix to add refcount once page is set private
+    - ubifs: rename_whiteout: correct old_dir size computing
+    - nvme: allow duplicate NSIDs for private namespaces
+    - nvme: fix the read-only state for zoned namespaces with unsupposed features
+    - wireguard: queueing: use CFI-safe ptr_ring cleanup function
+    - wireguard: socket: free skb in send6 when ipv6 is disabled
+    - wireguard: socket: ignore v6 endpoints when ipv6 is disabled
+    - XArray: Fix xas_create_range() when multi-order entry present
+    - can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path
+    - can: mcba_usb: properly check endpoint type
+    - can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix return of error value
+    - XArray: Update the LRU list in xas_split()
+    - modpost: restore the warning message for missing symbol versions
+    - rtc: check if __rtc_read_time was successful
+    - gfs2: gfs2_setattr_size error path fix
+    - gfs2: Make sure FITRIM minlen is rounded up to fs block size
+    - net: hns3: fix the concurrency between functions reading debugfs
+    - net: hns3: fix software vlan talbe of vlan 0 inconsistent with hardware
+    - rxrpc: fix some null-ptr-deref bugs in server_key.c
+    - rxrpc: Fix call timer start racing with call destruction
+    - mailbox: imx: fix wakeup failure from freeze mode
+    - crypto: arm/aes-neonbs-cbc - Select generic cbc and aes
+    - watch_queue: Free the page array when watch_queue is dismantled
+    - pinctrl: pinconf-generic: Print arguments for bias-pull-*
+    - watchdog: rti-wdt: Add missing pm_runtime_disable() in probe function
+    - net: sparx5: uses, depends on BRIDGE or !BRIDGE
+    - pinctrl: nuvoton: npcm7xx: Rename DS() macro to DSTR()
+    - pinctrl: nuvoton: npcm7xx: Use %zu printk format for ARRAY_SIZE()
+    - ASoC: mediatek: mt6358: add missing EXPORT_SYMBOLs
+    - ubi: Fix race condition between ctrl_cdev_ioctl and ubi_cdev_ioctl
+    - ARM: iop32x: offset IRQ numbers by 1
+    - block: Fix the maximum minor value is blk_alloc_ext_minor()
+    - io_uring: fix memory leak of uid in files registration
+    - riscv module: remove (NOLOAD)
+    - ACPI: CPPC: Avoid out of bounds access when parsing _CPC data
+    - vhost: handle error while adding split ranges to iotlb
+    - spi: Fix Tegra QSPI example
+    - platform/chrome: cros_ec_typec: Check for EC device
+    - can: isotp: restore accidentally removed MSG_PEEK feature
+    - proc: bootconfig: Add null pointer check
+    - drm/connector: Fix typo in documentation
+    - scsi: qla2xxx: Add qla2x00_async_done() for async routines
+    - staging: mt7621-dts: fix pinctrl-0 items to be size-1 items on ethernet
+    - arm64: mm: Drop 'const' from conditional arm64_dma_phys_limit definition
+    - ASoC: soc-compress: Change the check for codec_dai
+    - Reinstate some of "swiotlb: rework "fix info leak with DMA_FROM_DEVICE""
+    - tracing: Have type enum modifications copy the strings
+    - net: add skb_set_end_offset() helper
+    - net: preserve skb_end_offset() in skb_unclone_keeptruesize()
+    - mm/mmap: return 1 from stack_guard_gap __setup() handler
+    - ARM: 9187/1: JIVE: fix return value of __setup handler
+    - mm/memcontrol: return 1 from cgroup.memory __setup() handler
+    - mm/usercopy: return 1 from hardened_usercopy __setup() handler
+    - af_unix: Support POLLPRI for OOB.
+    - bpf: Adjust BPF stack helper functions to accommodate skip > 0
+    - bpf: Fix comment for helper bpf_current_task_under_cgroup()
+    - mmc: rtsx: Use pm_runtime_{get,put}() to handle runtime PM
+    - dt-bindings: mtd: nand-controller: Fix the reg property description
+    - dt-bindings: mtd: nand-controller: Fix a comment in the examples
+    - dt-bindings: spi: mxic: The interrupt property is not mandatory
+    - dt-bindings: memory: mtk-smi: No need mediatek,larb-id for mt8167
+    - dt-bindings: pinctrl: pinctrl-microchip-sgpio: Fix example
+    - ubi: fastmap: Return error code if memory allocation fails in add_aeb()
+    - ASoC: SOF: Intel: Fix build error without SND_SOC_SOF_PCI_DEV
+    - ASoC: topology: Allow TLV control to be either read or write
+    - perf vendor events: Update metrics for SkyLake Server
+    - media: ov6650: Add try support to selection API operations
+    - media: ov6650: Fix crop rectangle affected by set format
+    - spi: mediatek: support tick_delay without enhance_timing
+    - ARM: dts: spear1340: Update serial node properties
+    - ARM: dts: spear13xx: Update SPI dma properties
+    - arm64: dts: ls1043a: Update i2c dma properties
+    - arm64: dts: ls1046a: Update i2c node dma properties
+    - um: Fix uml_mconsole stop/go
+    - docs: sysctl/kernel: add missing bit to panic_print
+    - openvswitch: Fixed nd target mask field in the flow dump.
+    - torture: Make torture.sh help message match reality
+    - n64cart: convert bi_disk to bi_bdev->bd_disk fix build
+    - mmc: rtsx: Let MMC core handle runtime PM
+    - mmc: rtsx: Fix build errors/warnings for unused variable
+    - KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
+    - iommu/dma: Skip extra sync during unmap w/swiotlb
+    - iommu/dma: Fold _swiotlb helpers into callers
+    - iommu/dma: Check CONFIG_SWIOTLB more broadly
+    - swiotlb: Support aligned swiotlb buffers
+    - iommu/dma: Account for min_align_mask w/swiotlb
+    - coredump: Snapshot the vmas in do_coredump
+    - coredump: Remove the WARN_ON in dump_vma_snapshot
+    - coredump/elf: Pass coredump_params into fill_note_info
+    - coredump: Use the vma snapshot in fill_files_note
+    - PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
+    - Linux 5.15.33
+
+  * Jammy update: v5.15.32 upstream stable release (LP: #1969106)
+    - net: ipv6: fix skb_over_panic in __ip6_append_data
+    - tpm: Fix error handling in async work
+    - Bluetooth: btusb: Add another Realtek 8761BU
+    - llc: fix netdevice reference leaks in llc_ui_bind()
+    - ASoC: sti: Fix deadlock via snd_pcm_stop_xrun() call
+    - ALSA: oss: Fix PCM OSS buffer allocation overflow
+    - ALSA: usb-audio: add mapping for new Corsair Virtuoso SE
+    - ALSA: hda/realtek: Add quirk for Clevo NP70PNJ
+    - ALSA: hda/realtek: Add quirk for Clevo NP50PNJ
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
+    - ALSA: hda/realtek: Add quirk for ASUS GA402
+    - ALSA: pcm: Fix races among concurrent hw_params and hw_free calls
+    - ALSA: pcm: Fix races among concurrent read/write and buffer changes
+    - ALSA: pcm: Fix races among concurrent prepare and hw_params/hw_free calls
+    - ALSA: pcm: Fix races among concurrent prealloc proc writes
+    - ALSA: pcm: Add stream lock during PCM reset ioctl operations
+    - ALSA: usb-audio: Add mute TLV for playback volumes on RODE NT-USB
+    - ALSA: cmipci: Restore aux vol on suspend/resume
+    - ALSA: pci: fix reading of swapped values from pcmreg in AC97 codec
+    - drivers: net: xgene: Fix regression in CRC stripping
+    - ACPI / x86: Work around broken XSDT on Advantech DAC-BJ01 board
+    - ACPI: battery: Add device HID and quirk for Microsoft Surface Go 3
+    - ACPI: video: Force backlight native for Clevo NL5xRU and NL5xNU
+    - crypto: qat - disable registration of algorithms
+    - Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
+    - Revert "ath: add support for special 0x0 regulatory domain"
+    - drm/virtio: Ensure that objs is not NULL in virtio_gpu_array_put_free()
+    - rcu: Don't deboost before reporting expedited quiescent state
+    - uaccess: fix integer overflow on access_ok()
+    - mac80211: fix potential double free on mesh join
+    - tpm: use try_get_ops() in tpm-space.c
+    - wcn36xx: Differentiate wcn3660 from wcn3620
+    - m68k: fix access_ok for coldfire
+    - nds32: fix access_ok() checks in get/put_user
+    - llc: only change llc->dev when bind() succeeds
+    - Linux 5.15.32
+
+  * Jammy update: v5.15.31 upstream stable release (LP: #1969105)
+    - crypto: qcom-rng - ensure buffer for generate is completely filled
+    - ocfs2: fix crash when initialize filecheck kobj fails
+    - mm: swap: get rid of livelock in swapin readahead
+    - block: release rq qos structures for queue without disk
+    - drm/mgag200: Fix PLL setup for g200wb and g200ew
+    - efi: fix return value of __setup handlers
+    - alx: acquire mutex for alx_reinit in alx_change_mtu
+    - vsock: each transport cycles only on its own sockets
+    - esp6: fix check on ipv6_skip_exthdr's return value
+    - net: phy: marvell: Fix invalid comparison in the resume and suspend
+      functions
+    - net/packet: fix slab-out-of-bounds access in packet_recvmsg()
+    - atm: eni: Add check for dma_map_single
+    - iavf: Fix double free in iavf_reset_task
+    - hv_netvsc: Add check for kvmalloc_array
+    - drm/imx: parallel-display: Remove bus flags check in
+      imx_pd_bridge_atomic_check()
+    - drm/panel: simple: Fix Innolux G070Y2-L01 BPP settings
+    - net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
+    - drm: Don't make DRM_PANEL_BRIDGE dependent on DRM_KMS_HELPERS
+    - net: dsa: Add missing of_node_put() in dsa_port_parse_of
+    - net: phy: mscc: Add MODULE_FIRMWARE macros
+    - bnx2x: fix built-in kernel driver load failure
+    - net: bcmgenet: skip invalid partial checksums
+    - net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower
+      offload
+    - iavf: Fix hang during reboot/shutdown
+    - arm64: fix clang warning about TRAMP_VALIAS
+    - usb: gadget: rndis: prevent integer overflow in rndis_set_response()
+    - usb: gadget: Fix use-after-free bug by not setting udc->dev.driver
+    - usb: usbtmc: Fix bug in pipe direction for control transfers
+    - scsi: mpt3sas: Page fault in reply q processing
+    - Input: aiptek - properly check endpoint type
+    - perf symbols: Fix symbol size calculation condition
+    - btrfs: skip reserved bytes warning on unmount after log cleanup failure
+    - Linux 5.15.31
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Fri, 20 May 2022 14:58:09 +0200
+
+linux (5.15.0-33.34) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-33.34 -proposed tracker (LP: #1973924)
+
+  * CVE-2022-29581
+    - net/sched: cls_u32: fix netns refcount changes in u32_change()
+
+  * ext4: limit length to bitmap_maxbytes (LP: #1972281)
+    - ext4: limit length to bitmap_maxbytes - blocksize in punch_hole
+
+  * Unprivileged users may use PTRACE_SEIZE to set PTRACE_O_SUSPEND_SECCOMP
+    option (LP: #1972740)
+    - ptrace: Check PTRACE_O_SUSPEND_SECCOMP permission on PTRACE_SEIZE
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Wed, 18 May 2022 15:11:00 +0200
+
+linux (5.15.0-30.31) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-30.31 -proposed tracker (LP: #1971685)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2022.04.18)
+
+  * Intel: enable x86 AMX (LP: #1967750)
+    - x86/extable: Tidy up redundant handler functions
+    - x86/extable: Get rid of redundant macros
+    - x86/mce: Deduplicate exception handling
+    - x86/mce: Get rid of stray semicolons
+    - x86/extable: Rework the exception table mechanics
+    - x86/extable: Provide EX_TYPE_DEFAULT_MCE_SAFE and EX_TYPE_FAULT_MCE_SAFE
+    - x86/copy_mc: Use EX_TYPE_DEFAULT_MCE_SAFE for exception fixups
+    - x86/fpu: Use EX_TYPE_FAULT_MCE_SAFE for exception fixups
+    - x86/extable: Remove EX_TYPE_FAULT from MCE safe fixups
+    - x86/fpu/signal: Clarify exception handling in restore_fpregs_from_user()
+    - x86/fpu/signal: Move header zeroing out of xsave_to_user_sigframe()
+    - x86/fpu/signal: Move xstate clearing out of copy_fpregs_to_sigframe()
+    - x86/fpu/signal: Change return type of copy_fpstate_to_sigframe() to boolean
+    - x86/fpu/signal: Change return type of copy_fpregs_to_sigframe() helpers to
+      boolean
+    - x86/signal: Change return type of restore_sigcontext() to boolean
+    - x86/fpu/signal: Change return type of fpu__restore_sig() to boolean
+    - x86/fpu/signal: Change return type of __fpu_restore_sig() to boolean
+    - x86/fpu/signal: Change return code of check_xstate_in_sigframe() to boolean
+    - x86/fpu/signal: Change return code of restore_fpregs_from_user() to boolean
+    - x86/fpu/signal: Fix missed conversion to correct boolean retval in
+      save_xstate_epilog()
+    - x86/fpu: Remove pointless argument from switch_fpu_finish()
+    - x86/fpu: Update stale comments
+    - x86/pkru: Remove useless include
+    - x86/fpu: Restrict xsaves()/xrstors() to independent states
+    - x86/fpu: Cleanup the on_boot_cpu clutter
+    - x86/fpu: Remove pointless memset in fpu_clone()
+    - x86/process: Clone FPU in copy_thread()
+    - x86/fpu: Do not inherit FPU context for kernel and IO worker threads
+    - x86/fpu: Cleanup xstate xcomp_bv initialization
+    - x86/fpu/xstate: Provide and use for_each_xfeature()
+    - x86/fpu/xstate: Mark all init only functions __init
+    - x86/fpu: Move KVMs FPU swapping to FPU core
+    - x86/fpu: Replace KVMs home brewed FPU copy from user
+    - x86/fpu: Rework copy_xstate_to_uabi_buf()
+    - x86/fpu: Mark fpu__init_prepare_fx_sw_frame() as __init
+    - x86/fpu: Move context switch and exit to user inlines into sched.h
+    - x86/fpu: Clean up CPU feature tests
+    - x86/fpu: Make os_xrstor_booting() private
+    - x86/fpu: Move os_xsave() and os_xrstor() to core
+    - x86/fpu: Move legacy ASM wrappers to core
+    - x86/fpu: Make WARN_ON_FPU() private
+    - x86/fpu: Move fpregs_restore_userregs() to core
+    - x86/fpu: Move mxcsr related code to core
+    - x86/fpu: Move fpstate functions to api.h
+    - x86/fpu: Remove internal.h dependency from fpu/signal.h
+    - x86/sev: Include fpu/xcr.h
+    - x86/fpu: Mop up the internal.h leftovers
+    - x86/fpu: Replace the includes of fpu/internal.h
+    - x86/fpu: Provide a proper function for ex_handler_fprestore()
+    - x86/fpu: Replace KVMs home brewed FPU copy to user
+    - x86/fpu: Provide struct fpstate
+    - x86/fpu: Convert fpstate_init() to struct fpstate
+    - x86/fpu: Convert restore_fpregs_from_fpstate() to struct fpstate
+    - x86/fpu: Replace KVMs xstate component clearing
+    - x86/KVM: Convert to fpstate
+    - x86/fpu: Convert tracing to fpstate
+    - x86/fpu/regset: Convert to fpstate
+    - x86/fpu/signal: Convert to fpstate
+    - x86/fpu/core: Convert to fpstate
+    - x86/math-emu: Convert to fpstate
+    - x86/fpu: Remove fpu::state
+    - x86/fpu: Do not leak fpstate pointer on fork
+    - x86/process: Move arch_thread_struct_whitelist() out of line
+    - x86/fpu: Add size and mask information to fpstate
+    - x86/fpu: Use fpstate::size
+    - x86/fpu/xstate: Use fpstate for os_xsave()
+    - x86/fpu/xstate: Use fpstate for xsave_to_user_sigframe()
+    - x86/fpu: Use fpstate in fpu_copy_kvm_uabi_to_fpstate()
+    - x86/fpu: Use fpstate in __copy_xstate_to_uabi_buf()
+    - x86/fpu/xstate: Use fpstate for copy_uabi_to_xstate()
+    - x86/fpu/signal: Use fpstate for size and features
+    - x86/fpu: Provide struct fpu_config
+    - x86/fpu: Cleanup fpu__init_system_xstate_size_legacy()
+    - x86/fpu/xstate: Cleanup size calculations
+    - x86/fpu: Move xstate size to fpu_*_cfg
+    - x86/fpu: Move xstate feature masks to fpu_*_cfg
+    - x86/fpu: Mop up xfeatures_mask_uabi()
+    - x86/fpu: Rework restore_regs_from_fpstate()
+    - x86/fpu/xstate: Move remaining xfeature helpers to core
+    - x86/fpu: Prepare for sanitizing KVM FPU code
+    - x86/fpu: Provide infrastructure for KVM FPU cleanup
+    - x86/kvm: Convert FPU handling to a single swap buffer
+    - x86/fpu: Remove old KVM FPU interface
+    - signal: Add an optional check for altstack size
+    - x86/signal: Implement sigaltstack size validation
+    - x86/fpu/xstate: Provide xstate_calculate_size()
+    - x86/fpu: Add members to struct fpu to cache permission information
+    - x86/fpu: Add fpu_state_config::legacy_features
+    - x86/arch_prctl: Add controls for dynamic XSTATE components
+    - x86/fpu: Add basic helpers for dynamically enabled features
+    - x86/signal: Use fpu::__state_user_size for sigalt stack validation
+    - x86/fpu/signal: Prepare for variable sigframe length
+    - x86/fpu: Prepare fpu_clone() for dynamically enabled features
+    - x86/fpu: Reset permission and fpstate on exec()
+    - x86/cpufeatures: Add eXtended Feature Disabling (XFD) feature bit
+    - x86/msr-index: Add MSRs for XFD
+    - x86/fpu: Add XFD state to fpstate
+    - x86/fpu: Add sanity checks for XFD
+    - x86/fpu: Update XFD state where required
+    - x86/fpu/xstate: Add XFD #NM handler
+    - x86/fpu/xstate: Add fpstate_realloc()/free()
+    - x86/fpu/xstate: Prepare XSAVE feature table for gaps in state component
+      numbers
+    - x86/fpu/amx: Define AMX state components and have it used for boot-time
+      checks
+    - x86/fpu: Calculate the default sizes independently
+    - x86/fpu: Add XFD handling for dynamic states
+    - x86/fpu/amx: Enable the AMX feature in 64-bit mode
+    - selftests/x86/amx: Add test cases for AMX state management
+    - selftests/x86/amx: Add context switch test
+    - Documentation/x86: Add documentation for using dynamic XSTATE features
+    - x86/fpu/signal: Initialize sw_bytes in save_xstate_epilog()
+    - signal: Skip the altstack update when not needed
+    - x86/cpufeatures: Put the AMX macros in the word 18 block
+    - x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
+    - selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
+    - [Config] updateconfigs after AMX patchset
+
+ -- Stefan Bader <stefan.bader@canonical.com>  Thu, 05 May 2022 11:45:39 +0200
+
+linux (5.15.0-27.28) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-27.28 -proposed tracker (LP: #1968954)
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 14 Apr 2022 06:46:57 +0200
+
+linux (5.15.0-26.27) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-26.27 -proposed tracker (LP: #1968850)
+
+  * CVE-2022-1016
+    - netfilter: nf_tables: initialize registers in nft_do_chain()
+
+  * CVE-2022-1015
+    - netfilter: nf_tables: validate registers coming from userspace.
+
+  * CVE-2022-26490
+    - nfc: st21nfca: Fix potential buffer overflows in EVT_TRANSACTION
+
+  * harden indirect calls against BHI attacks (LP: #1967579)
+    - objtool: Classify symbols
+    - objtool: Explicitly avoid self modifying code in .altinstr_replacement
+    - objtool: Shrink struct instruction
+    - objtool,x86: Replace alternatives with .retpoline_sites
+    - x86/retpoline: Remove unused replacement symbols
+    - x86/asm: Fix register order
+    - x86/asm: Fixup odd GEN-for-each-reg.h usage
+    - x86/retpoline: Move the retpoline thunk declarations to nospec-branch.h
+    - x86/retpoline: Create a retpoline thunk array
+    - x86/alternative: Implement .retpoline_sites support
+    - x86/alternative: Handle Jcc __x86_indirect_thunk_\reg
+    - x86/alternative: Try inline spectre_v2=retpoline,amd
+    - x86/alternative: Add debug prints to apply_retpolines()
+    - bpf,x86: Simplify computing label offsets
+    - bpf,x86: Respect X86_FEATURE_RETPOLINE*
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Wed, 13 Apr 2022 16:51:38 +0200
+
+linux (5.15.0-25.25) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-25.25 -proposed tracker (LP: #1967146)
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "scsi: core: Reallocate device's budget map on queue depth
+      change"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Wed, 30 Mar 2022 17:28:11 +0200
+
+linux (5.15.0-24.24) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-24.24 -proposed tracker (LP: #1966305)
+
+  * Update OS policy capability handshake (LP: #1966089)
+    - thermal: int340x: Update OS policy capability handshake
+
+  * Jammy update: v5.15.30 upstream stable release (LP: #1966057)
+    - Revert "xfrm: state and policy should fail if XFRMA_IF_ID 0"
+    - arm64: dts: rockchip: fix rk3399-puma-haikou USB OTG mode
+    - xfrm: Check if_id in xfrm_migrate
+    - xfrm: Fix xfrm migrate issues when address family changes
+    - arm64: dts: rockchip: fix rk3399-puma eMMC HS400 signal integrity
+    - arm64: dts: rockchip: align pl330 node name with dtschema
+    - arm64: dts: rockchip: reorder rk3399 hdmi clocks
+    - arm64: dts: agilex: use the compatible "intel,socfpga-agilex-hsotg"
+    - ARM: dts: rockchip: reorder rk322x hmdi clocks
+    - ARM: dts: rockchip: fix a typo on rk3288 crypto-controller
+    - mac80211: refuse aggregations sessions before authorized
+    - MIPS: smp: fill in sibling and core maps earlier
+    - ARM: 9178/1: fix unmet dependency on BITREVERSE for HAVE_ARCH_BITREVERSE
+    - Bluetooth: hci_core: Fix leaking sent_cmd skb
+    - can: rcar_canfd: rcar_canfd_channel_probe(): register the CAN device when
+      fully ready
+    - atm: firestream: check the return value of ioremap() in fs_init()
+    - iwlwifi: don't advertise TWT support
+    - drm/vrr: Set VRR capable prop only if it is attached to connector
+    - nl80211: Update bss channel on channel switch for P2P_CLIENT
+    - tcp: make tcp_read_sock() more robust
+    - sfc: extend the locking on mcdi->seqno
+    - bnx2: Fix an error message
+    - kselftest/vm: fix tests build with old libc
+    - x86/module: Fix the paravirt vs alternative order
+    - ice: Fix race condition during interface enslave
+    - Linux 5.15.30
+
+  * Jammy update: v5.15.29 upstream stable release (LP: #1966056)
+    - arm64: dts: qcom: sm8350: Describe GCC dependency clocks
+    - arm64: dts: qcom: sm8350: Correct UFS symbol clocks
+    - HID: elo: Revert USB reference counting
+    - HID: hid-thrustmaster: fix OOB read in thrustmaster_interrupts
+    - ARM: boot: dts: bcm2711: Fix HVS register range
+    - clk: qcom: gdsc: Add support to update GDSC transition delay
+    - clk: qcom: dispcc: Update the transition delay for MDSS GDSC
+    - HID: vivaldi: fix sysfs attributes leak
+    - arm64: dts: armada-3720-turris-mox: Add missing ethernet0 alias
+    - tipc: fix kernel panic when enabling bearer
+    - vdpa/mlx5: add validation for VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET command
+    - vduse: Fix returning wrong type in vduse_domain_alloc_iova()
+    - net: phy: meson-gxl: fix interrupt handling in forced mode
+    - mISDN: Fix memory leak in dsp_pipeline_build()
+    - vhost: fix hung thread due to erroneous iotlb entries
+    - virtio-blk: Don't use MAX_DISCARD_SEGMENTS if max_discard_seg is zero
+    - vdpa: fix use-after-free on vp_vdpa_remove
+    - isdn: hfcpci: check the return value of dma_set_mask() in setup_hw()
+    - net: qlogic: check the return value of dma_alloc_coherent() in
+      qed_vf_hw_prepare()
+    - esp: Fix possible buffer overflow in ESP transformation
+    - esp: Fix BEET mode inter address family tunneling on GSO
+    - qed: return status of qed_iov_get_link
+    - smsc95xx: Ignore -ENODEV errors when device is unplugged
+    - gpiolib: acpi: Convert ACPI value of debounce to microseconds
+    - drm/sun4i: mixer: Fix P010 and P210 format numbers
+    - net: dsa: mt7530: fix incorrect test in mt753x_phylink_validate()
+    - ARM: dts: aspeed: Fix AST2600 quad spi group
+    - iavf: Fix handling of vlan strip virtual channel messages
+    - i40e: stop disabling VFs due to PF error responses
+    - ice: stop disabling VFs due to PF error responses
+    - ice: Fix error with handling of bonding MTU
+    - ice: Don't use GFP_KERNEL in atomic context
+    - ice: Fix curr_link_speed advertised speed
+    - ethernet: Fix error handling in xemaclite_of_probe
+    - tipc: fix incorrect order of state message data sanity check
+    - net: ethernet: ti: cpts: Handle error for clk_enable
+    - net: ethernet: lpc_eth: Handle error for clk_enable
+    - net: marvell: prestera: Add missing of_node_put() in
+      prestera_switch_set_base_mac_addr
+    - ax25: Fix NULL pointer dereference in ax25_kill_by_device
+    - net/mlx5: Fix size field in bufferx_reg struct
+    - net/mlx5: Fix a race on command flush flow
+    - net/mlx5e: Lag, Only handle events from highest priority multipath entry
+    - NFC: port100: fix use-after-free in port100_send_complete
+    - selftests: pmtu.sh: Kill tcpdump processes launched by subshell.
+    - selftests: pmtu.sh: Kill nettest processes launched in subshell.
+    - gpio: ts4900: Do not set DAT and OE together
+    - gianfar: ethtool: Fix refcount leak in gfar_get_ts_info
+    - net: phy: DP83822: clear MISR2 register to disable interrupts
+    - sctp: fix kernel-infoleak for SCTP sockets
+    - net: bcmgenet: Don't claim WOL when its not available
+    - net: phy: meson-gxl: improve link-up behavior
+    - selftests/bpf: Add test for bpf_timer overwriting crash
+    - swiotlb: fix info leak with DMA_FROM_DEVICE
+    - usb: dwc3: pci: add support for the Intel Raptor Lake-S
+    - pinctrl: tigerlake: Revert "Add Alder Lake-M ACPI ID"
+    - KVM: Fix lockdep false negative during host resume
+    - kvm: x86: Disable KVM_HC_CLOCK_PAIRING if tsc is in always catchup mode
+    - spi: rockchip: Fix error in getting num-cs property
+    - spi: rockchip: terminate dma transmission when slave abort
+    - drm/vc4: hdmi: Unregister codec device on unbind
+    - x86/kvm: Don't use pv tlb/ipi/sched_yield if on 1 vCPU
+    - net-sysfs: add check for netdevice being present to speed_show
+    - hwmon: (pmbus) Clear pmbus fault/warning bits after read
+    - PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
+    - gpio: Return EPROBE_DEFER if gc->to_irq is NULL
+    - drm/amdgpu: bypass tiling flag check in virtual display case (v2)
+    - Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
+    - Revert "xen-netback: Check for hotplug-status existence before watching"
+    - ipv6: prevent a possible race condition with lifetimes
+    - tracing: Ensure trace buffer is at least 4096 bytes large
+    - tracing/osnoise: Make osnoise_main to sleep for microseconds
+    - selftest/vm: fix map_fixed_noreplace test failure
+    - selftests/memfd: clean up mapping in mfd_fail_write
+    - ARM: Spectre-BHB: provide empty stub for non-config
+    - fuse: fix fileattr op failure
+    - fuse: fix pipe buffer lifetime for direct_io
+    - staging: rtl8723bs: Fix access-point mode deadlock
+    - staging: gdm724x: fix use after free in gdm_lte_rx()
+    - net: macb: Fix lost RX packet wakeup race in NAPI receive
+    - riscv: alternative only works on !XIP_KERNEL
+    - mmc: meson: Fix usage of meson_mmc_post_req()
+    - riscv: Fix auipc+jalr relocation range checks
+    - tracing/osnoise: Force quiescent states while tracing
+    - arm64: dts: marvell: armada-37xx: Remap IO space to bus address 0x0
+    - arm64: Ensure execute-only permissions are not allowed without EPAN
+    - arm64: kasan: fix include error in MTE functions
+    - swiotlb: rework "fix info leak with DMA_FROM_DEVICE"
+    - KVM: x86/mmu: kvm_faultin_pfn has to return false if pfh is returned
+    - virtio: unexport virtio_finalize_features
+    - virtio: acknowledge all features before access
+    - net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
+    - ARM: fix Thumb2 regression with Spectre BHB
+    - watch_queue: Fix filter limit check
+    - watch_queue, pipe: Free watchqueue state after clearing pipe ring
+    - watch_queue: Fix to release page in ->release()
+    - watch_queue: Fix to always request a pow-of-2 pipe ring size
+    - watch_queue: Fix the alloc bitmap size to reflect notes allocated
+    - watch_queue: Free the alloc bitmap when the watch_queue is torn down
+    - watch_queue: Fix lack of barrier/sync/lock between post and read
+    - watch_queue: Make comment about setting ->defunct more accurate
+    - x86/boot: Fix memremap of setup_indirect structures
+    - x86/boot: Add setup_indirect support in early_memremap_is_setup_data()
+    - x86/sgx: Free backing memory after faulting the enclave page
+    - x86/traps: Mark do_int3() NOKPROBE_SYMBOL
+    - drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP
+    - btrfs: make send work with concurrent block group relocation
+    - drm/i915: Workaround broken BIOS DBUF configuration on TGL/RKL
+    - riscv: dts: k210: fix broken IRQs on hart1
+    - block: drop unused includes in <linux/genhd.h>
+    - Revert "net: dsa: mv88e6xxx: flush switchdev FDB workqueue before removing
+      VLAN"
+    - vhost: allow batching hint without size
+    - Linux 5.15.29
+
+  * Jammy update: v5.15.28 upstream stable release (LP: #1966055)
+    - slip: fix macro redefine warning
+    - ARM: fix co-processor register typo
+    - ARM: Do not use NOCROSSREFS directive with ld.lld
+    - arm64: Do not include __READ_ONCE() block in assembly files
+    - ARM: fix build warning in proc-v7-bugs.c
+    - xen/xenbus: don't let xenbus_grant_ring() remove grants in error case
+    - xen/grant-table: add gnttab_try_end_foreign_access()
+    - xen/blkfront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/netfront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/scsifront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/gntalloc: don't use gnttab_query_foreign_access()
+    - xen: remove gnttab_query_foreign_access()
+    - xen/9p: use alloc/free_pages_exact()
+    - xen/pvcalls: use alloc/free_pages_exact()
+    - xen/gnttab: fix gnttab_end_foreign_access() without page specified
+    - xen/netfront: react properly to failing gnttab_end_foreign_access_ref()
+    - Revert "ACPI: PM: s2idle: Cancel wakeup before dispatching EC GPE"
+    - Linux 5.15.28
+
+  * zfcpdump-kernel update to v5.15 (LP: #1965766)
+    - SAUCE: Audit: Fix incorrect static inline function declration.
+
+  * [22.04 FEAT] SMC-R v2 Support (LP: #1929035)
+    - net/smc: save stack space and allocate smc_init_info
+    - net/smc: prepare for SMC-Rv2 connection
+    - net/smc: add SMC-Rv2 connection establishment
+    - net/smc: add listen processing for SMC-Rv2
+    - net/smc: add v2 format of CLC decline message
+    - net/smc: retrieve v2 gid from IB device
+    - net/smc: add v2 support to the work request layer
+    - net/smc: extend LLC layer for SMC-Rv2
+    - net/smc: add netlink support for SMC-Rv2
+    - net/smc: stop links when their GID is removed
+    - net/smc: fix kernel panic caused by race of smc_sock
+    - net/smc: Fix hung_task when removing SMC-R devices
+
+  * [22.04 FEAT] Transparent PCI device recovery (LP: #1959532)
+    - s390/pci: tolerate inconsistent handle in recover
+    - s390/pci: add simpler s390dbf traces for events
+    - s390/pci: refresh function handle in iomap
+    - s390/pci: implement reset_slot for hotplug slot
+    - PCI: Export pci_dev_lock()
+    - s390/pci: implement minimal PCI error recovery
+
+  * Mute/mic LEDs no function on some HP platfroms (LP: #1965080)
+    - ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machines
+
+  * [22.04 FEAT] smc: Add User-defined EID (Enterprise ID) Support - kernel
+    (LP: #1929060)
+    - net/smc: add support for user defined EIDs
+    - net/smc: keep static copy of system EID
+    - net/smc: add generic netlink support for system EID
+
+  * Rotate to 2021v1 signing key (LP: #1964990)
+    - [Packaging] Rotate to 2021v1 signing key
+
+  * [22.04 FEAT] zcrypt DD: Exploitation Support of new IBM Z Crypto Hardware
+    (kernel part) (LP: #1959547)
+    - s390/zcrypt: rework of debug feature messages
+    - s390/ap/zcrypt: debug feature improvements
+    - s390/zcrypt: CEX8S exploitation support
+    - s390/zcrypt: handle checkstopped cards with new state
+    - s390/zcrypt: Support CPRB minor version T7
+    - s390/zcrypt: change reply buffer size offering
+    - s390/zcrypt: Provide target domain for EP11 cprbs to scheduling function
+    - s390/airq: use DMA memory for summary indicators
+
+  * [22.04 FEAT] [VS2103] Set KVM_CAP_S390_MEM_OP_EXTENSION capability to 211
+    (LP: #1963901)
+    - SAUCE: Set KVM_CAP_S390_MEM_OP_EXTENSION capability to 211
+
+  * dependency on crda obsolete according to Debian (LP: #1958918)
+    - [Packaging] switch dependency from crda to wireless-regdb
+
+  * Cirrus audio support [1028:0BB5] & [1028:0BB6] (LP: #1964748)
+    - ALSA: hda/cs8409: Add new Warlock SKUs to patch_cs8409
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] mark dkms-build-configure--zfs executable
+    - [Packaging] Fix bashism in dkms-build script
+    - [Packaging] Always catch errors in dkms-build scripts
+    - [Config] toolchain version update
+
+  * Miscellaneous upstream changes
+    - Ubuntu: remove leftover reference to ubuntu/hio driver
+    - Reverting commits 61005756c824 and cdb0f8e66513 due to a conflict with
+      LP#1929035. Re-pick them afterwards, which will establish the upstream
+      commit content and order again.
+    - Revert "UBUNTU: [Packaging] Rotate to 2021v1 signing key"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Fri, 25 Mar 2022 11:25:10 +0100
+
+linux (5.15.0-23.23) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-23.23 -proposed tracker (LP: #1964573)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync dkms-build{,--nvidia-N} from LRMv5
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * [22.04 FEAT] KVM: Enable GISA support for Secure Execution guests
+    (LP: #1959977)
+    - KVM: s390: pv: make use of ultravisor AIV support
+
+  * intel_iommu breaks Intel IPU6 camera: isys port open ready failed -16
+    (LP: #1958004)
+    - SAUCE: iommu: intel-ipu: use IOMMU passthrough mode for Intel IPUs
+
+  * CVE-2022-23960
+    - ARM: report Spectre v2 status through sysfs
+    - ARM: early traps initialisation
+    - ARM: use LOADADDR() to get load address of sections
+    - ARM: Spectre-BHB workaround
+    - ARM: include unprivileged BPF status in Spectre V2 reporting
+    - arm64: Add Neoverse-N2, Cortex-A710 CPU part definition
+    - arm64: Add HWCAP for self-synchronising virtual counter
+    - arm64: Add Cortex-X2 CPU part definition
+    - arm64: add ID_AA64ISAR2_EL1 sys register
+    - arm64: cpufeature: add HWCAP for FEAT_AFP
+    - arm64: cpufeature: add HWCAP for FEAT_RPRES
+    - arm64: entry.S: Add ventry overflow sanity checks
+    - arm64: spectre: Rename spectre_v4_patch_fw_mitigation_conduit
+    - KVM: arm64: Allow indirect vectors to be used without SPECTRE_V3A
+    - arm64: entry: Make the trampoline cleanup optional
+    - arm64: entry: Free up another register on kpti's tramp_exit path
+    - arm64: entry: Move the trampoline data page before the text page
+    - arm64: entry: Allow tramp_alias to access symbols after the 4K boundary
+    - arm64: entry: Don't assume tramp_vectors is the start of the vectors
+    - arm64: entry: Move trampoline macros out of ifdef'd section
+    - arm64: entry: Make the kpti trampoline's kpti sequence optional
+    - arm64: entry: Allow the trampoline text to occupy multiple pages
+    - arm64: entry: Add non-kpti __bp_harden_el1_vectors for mitigations
+    - arm64: entry: Add vectors that have the bhb mitigation sequences
+    - arm64: entry: Add macro for reading symbol addresses from the trampoline
+    - arm64: Add percpu vectors for EL1
+    - arm64: proton-pack: Report Spectre-BHB vulnerabilities as part of Spectre-v2
+    - arm64: Mitigate spectre style branch history side channels
+    - KVM: arm64: Allow SMCCC_ARCH_WORKAROUND_3 to be discovered and migrated
+    - arm64: Use the clearbhb instruction in mitigations
+    - arm64: proton-pack: Include unprivileged eBPF status in Spectre v2
+      mitigation reporting
+    - ARM: fix build error when BPF_SYSCALL is disabled
+
+  * CVE-2021-26401
+    - x86/speculation: Use generic retpoline by default on AMD
+    - x86/speculation: Update link to AMD speculation whitepaper
+    - x86/speculation: Warn about Spectre v2 LFENCE mitigation
+    - x86/speculation: Warn about eIBRS + LFENCE + Unprivileged eBPF + SMT
+
+  * CVE-2022-0001
+    - x86,bugs: Unconditionally allow spectre_v2=retpoline,amd
+    - x86/speculation: Rename RETPOLINE_AMD to RETPOLINE_LFENCE
+    - x86/speculation: Add eIBRS + Retpoline options
+    - Documentation/hw-vuln: Update spectre doc
+    - x86/speculation: Include unprivileged eBPF status in Spectre v2 mitigation
+      reporting
+
+  * Jammy update: v5.15.27 upstream stable release (LP: #1964361)
+    - mac80211_hwsim: report NOACK frames in tx_status
+    - mac80211_hwsim: initialize ieee80211_tx_info at hw_scan_work
+    - i2c: bcm2835: Avoid clock stretching timeouts
+    - ASoC: rt5668: do not block workqueue if card is unbound
+    - ASoC: rt5682: do not block workqueue if card is unbound
+    - regulator: core: fix false positive in regulator_late_cleanup()
+    - Input: clear BTN_RIGHT/MIDDLE on buttonpads
+    - btrfs: get rid of warning on transaction commit when using flushoncommit
+    - KVM: arm64: vgic: Read HW interrupt pending state from the HW
+    - block: loop:use kstatfs.f_bsize of backing file to set discard granularity
+    - tipc: fix a bit overflow in tipc_crypto_key_rcv()
+    - cifs: do not use uninitialized data in the owner/group sid
+    - cifs: fix double free race when mount fails in cifs_get_root()
+    - cifs: modefromsids must add an ACE for authenticated users
+    - selftests/seccomp: Fix seccomp failure by adding missing headers
+    - drm/amd/pm: correct UMD pstate clocks for Dimgrey Cavefish and Beige Goby
+    - dmaengine: shdma: Fix runtime PM imbalance on error
+    - i2c: cadence: allow COMPILE_TEST
+    - i2c: imx: allow COMPILE_TEST
+    - i2c: qup: allow COMPILE_TEST
+    - net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
+    - block-map: add __GFP_ZERO flag for alloc_page in function bio_copy_kern
+    - usb: gadget: don't release an existing dev->buf
+    - usb: gadget: clear related members when goto fail
+    - exfat: reuse exfat_inode_info variable instead of calling EXFAT_I()
+    - exfat: fix i_blocks for files truncated over 4 GiB
+    - tracing: Add test for user space strings when filtering on string pointers
+    - arm64: Mark start_backtrace() notrace and NOKPROBE_SYMBOL
+    - serial: stm32: prevent TDR register overwrite when sending x_char
+    - ext4: drop ineligible txn start stop APIs
+    - ext4: simplify updating of fast commit stats
+    - ext4: fast commit may not fallback for ineligible commit
+    - ext4: fast commit may miss file actions
+    - sched/fair: Fix fault in reweight_entity
+    - ata: pata_hpt37x: fix PCI clock detection
+    - drm/amdgpu: check vm ready by amdgpu_vm->evicting flag
+    - tracing: Add ustring operation to filtering string pointers
+    - ipv6: fix skb drops in igmp6_event_query() and igmp6_event_report()
+    - NFSD: Have legacy NFSD WRITE decoders use xdr_stream_subsegment()
+    - NFSD: Fix zero-length NFSv3 WRITEs
+    - io_uring: fix no lock protection for ctx->cq_extra
+    - tools/resolve_btf_ids: Close ELF file on error
+    - mtd: spi-nor: Fix mtd size for s3an flashes
+    - MIPS: fix local_{add,sub}_return on MIPS64
+    - signal: In get_signal test for signal_group_exit every time through the loop
+    - PCI: mediatek-gen3: Disable DVFSRC voltage request
+    - PCI: rcar: Check if device is runtime suspended instead of
+      __clk_is_enabled()
+    - PCI: dwc: Do not remap invalid res
+    - PCI: aardvark: Fix checking for MEM resource type
+    - KVM: VMX: Don't unblock vCPU w/ Posted IRQ if IRQs are disabled in guest
+    - KVM: s390: Ensure kvm_arch_no_poll() is read once when blocking vCPU
+    - KVM: VMX: Read Posted Interrupt "control" exactly once per loop iteration
+    - KVM: X86: Ensure that dirty PDPTRs are loaded
+    - KVM: x86: Handle 32-bit wrap of EIP for EMULTYPE_SKIP with flat code seg
+    - KVM: x86: Exit to userspace if emulation prepared a completion callback
+    - i3c: fix incorrect address slot lookup on 64-bit
+    - i3c/master/mipi-i3c-hci: Fix a potentially infinite loop in
+      'hci_dat_v1_get_index()'
+    - tracing: Do not let synth_events block other dyn_event systems during create
+    - Input: ti_am335x_tsc - set ADCREFM for X configuration
+    - Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2
+    - PCI: mvebu: Check for errors from pci_bridge_emul_init() call
+    - PCI: mvebu: Do not modify PCI IO type bits in conf_write
+    - PCI: mvebu: Fix support for bus mastering and PCI_COMMAND on emulated bridge
+    - PCI: mvebu: Fix configuring secondary bus of PCIe Root Port via emulated
+      bridge
+    - PCI: mvebu: Setup PCIe controller to Root Complex mode
+    - PCI: mvebu: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
+    - PCI: mvebu: Fix support for PCI_EXP_DEVCTL on emulated bridge
+    - PCI: mvebu: Fix support for PCI_EXP_RTSTA on emulated bridge
+    - PCI: mvebu: Fix support for DEVCAP2, DEVCTL2 and LNKCTL2 registers on
+      emulated bridge
+    - NFSD: Fix verifier returned in stable WRITEs
+    - Revert "nfsd: skip some unnecessary stats in the v4 case"
+    - nfsd: fix crash on COPY_NOTIFY with special stateid
+    - x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
+    - drm/i915: don't call free_mmap_offset when purging
+    - SUNRPC: Fix sockaddr handling in the svc_xprt_create_error trace point
+    - SUNRPC: Fix sockaddr handling in svcsock_accept_class trace points
+    - drm/sun4i: dw-hdmi: Fix missing put_device() call in sun8i_hdmi_phy_get
+    - drm/atomic: Check new_crtc_state->active to determine if CRTC needs disable
+      in self refresh mode
+    - ntb_hw_switchtec: Fix pff ioread to read into mmio_part_cfg_all
+    - ntb_hw_switchtec: Fix bug with more than 32 partitions
+    - drm/amdkfd: Check for null pointer after calling kmemdup
+    - drm/amdgpu: use spin_lock_irqsave to avoid deadlock by local interrupt
+    - i3c: master: dw: check return of dw_i3c_master_get_free_pos()
+    - dma-buf: cma_heap: Fix mutex locking section
+    - tracing/uprobes: Check the return value of kstrdup() for tu->filename
+    - tracing/probes: check the return value of kstrndup() for pbuf
+    - mm: defer kmemleak object creation of module_alloc()
+    - kasan: fix quarantine conflicting with init_on_free
+    - selftests/vm: make charge_reserved_hugetlb.sh work with existing cgroup
+      setting
+    - hugetlbfs: fix off-by-one error in hugetlb_vmdelete_list()
+    - drm/amdgpu/display: Only set vblank_disable_immediate when PSR is not
+      enabled
+    - drm/amdgpu: filter out radeon PCI device IDs
+    - drm/amdgpu: filter out radeon secondary ids as well
+    - drm/amd/display: Use adjusted DCN301 watermarks
+    - drm/amd/display: move FPU associated DSC code to DML folder
+    - ethtool: Fix link extended state for big endian
+    - octeontx2-af: Optimize KPU1 processing for variable-length headers
+    - octeontx2-af: Reset PTP config in FLR handler
+    - octeontx2-af: cn10k: RPM hardware timestamp configuration
+    - octeontx2-af: cn10k: Use appropriate register for LMAC enable
+    - octeontx2-af: Adjust LA pointer for cpt parse header
+    - octeontx2-af: Add KPU changes to parse NGIO as separate layer
+    - net/mlx5e: IPsec: Refactor checksum code in tx data path
+    - net/mlx5e: IPsec: Fix crypto offload for non TCP/UDP encapsulated traffic
+    - bpf: Use u64_stats_t in struct bpf_prog_stats
+    - bpf: Fix possible race in inc_misses_counter
+    - drm/amd/display: Update watermark values for DCN301
+    - drm: mxsfb: Set fallback bus format when the bridge doesn't provide one
+    - drm: mxsfb: Fix NULL pointer dereference
+    - riscv/mm: Add XIP_FIXUP for phys_ram_base
+    - drm/i915/display: split out dpt out of intel_display.c
+    - drm/i915/display: Move DRRS code its own file
+    - drm/i915: Disable DRRS on IVB/HSW port != A
+    - gve: Recording rx queue before sending to napi
+    - net: dsa: ocelot: seville: utilize of_mdiobus_register
+    - net: dsa: seville: register the mdiobus under devres
+    - ibmvnic: don't release napi in __ibmvnic_open()
+    - of: net: move of_net under net/
+    - net: ethernet: litex: Add the dependency on HAS_IOMEM
+    - drm/mediatek: mtk_dsi: Reset the dsi0 hardware
+    - cifs: protect session channel fields with chan_lock
+    - cifs: fix confusing unneeded warning message on smb2.1 and earlier
+    - drm/amd/display: Fix stream->link_enc unassigned during stream removal
+    - bnxt_en: Fix occasional ethtool -t loopback test failures
+    - drm/amd/display: For vblank_disable_immediate, check PSR is really used
+    - PCI: mvebu: Fix device enumeration regression
+    - net: of: fix stub of_net helpers for CONFIG_NET=n
+    - ALSA: intel_hdmi: Fix reference to PCM buffer address
+    - ucounts: Fix systemd LimitNPROC with private users regression
+    - riscv/efi_stub: Fix get_boot_hartid_from_fdt() return value
+    - riscv: Fix config KASAN && SPARSEMEM && !SPARSE_VMEMMAP
+    - riscv: Fix config KASAN && DEBUG_VIRTUAL
+    - iwlwifi: mvm: check debugfs_dir ptr before use
+    - ASoC: ops: Shift tested values in snd_soc_put_volsw() by +min
+    - iommu/vt-d: Fix double list_add when enabling VMD in scalable mode
+    - iommu/amd: Recover from event log overflow
+    - drm/i915: s/JSP2/ICP2/ PCH
+    - drm/amd/display: Reduce dmesg error to a debug print
+    - xen/netfront: destroy queues before real_num_tx_queues is zeroed
+    - thermal: core: Fix TZ_GET_TRIP NULL pointer dereference
+    - mac80211: fix EAPoL rekey fail in 802.3 rx path
+    - blktrace: fix use after free for struct blk_trace
+    - ntb: intel: fix port config status offset for SPR
+    - mm: Consider __GFP_NOWARN flag for oversized kvmalloc() calls
+    - xfrm: fix MTU regression
+    - netfilter: fix use-after-free in __nf_register_net_hook()
+    - bpf, sockmap: Do not ignore orig_len parameter
+    - xfrm: fix the if_id check in changelink
+    - xfrm: enforce validity of offload input flags
+    - e1000e: Correct NVM checksum verification flow
+    - net: fix up skbs delta_truesize in UDP GRO frag_list
+    - netfilter: nf_queue: don't assume sk is full socket
+    - netfilter: nf_queue: fix possible use-after-free
+    - netfilter: nf_queue: handle socket prefetch
+    - batman-adv: Request iflink once in batadv-on-batadv check
+    - batman-adv: Request iflink once in batadv_get_real_netdevice
+    - batman-adv: Don't expect inter-netns unique iflink indices
+    - net: ipv6: ensure we call ipv6_mc_down() at most once
+    - net: dcb: flush lingering app table entries for unregistered devices
+    - net: ipa: add an interconnect dependency
+    - net/smc: fix connection leak
+    - net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error generated by client
+    - net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error cause by server
+    - btrfs: fix ENOSPC failure when attempting direct IO write into NOCOW range
+    - mac80211: fix forwarded mesh frames AC & queue selection
+    - net: stmmac: fix return value of __setup handler
+    - mac80211: treat some SAE auth steps as final
+    - iavf: Fix missing check for running netdev
+    - net: sxgbe: fix return value of __setup handler
+    - ibmvnic: register netdev after init of adapter
+    - net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe()
+    - ixgbe: xsk: change !netif_carrier_ok() handling in ixgbe_xmit_zc()
+    - iavf: Fix deadlock in iavf_reset_task
+    - efivars: Respect "block" flag in efivar_entry_set_safe()
+    - auxdisplay: lcd2s: Fix lcd2s_redefine_char() feature
+    - firmware: arm_scmi: Remove space in MODULE_ALIAS name
+    - ASoC: cs4265: Fix the duplicated control name
+    - auxdisplay: lcd2s: Fix memory leak in ->remove()
+    - auxdisplay: lcd2s: Use proper API to free the instance of charlcd object
+    - can: gs_usb: change active_channels's type from atomic_t to u8
+    - iommu/tegra-smmu: Fix missing put_device() call in tegra_smmu_find
+    - arm64: dts: rockchip: Switch RK3399-Gru DP to SPDIF output
+    - igc: igc_read_phy_reg_gpy: drop premature return
+    - ARM: Fix kgdb breakpoint for Thumb2
+    - mips: setup: fix setnocoherentio() boolean setting
+    - ARM: 9182/1: mmu: fix returns from early_param() and __setup() functions
+    - mptcp: Correctly set DATA_FIN timeout when number of retransmits is large
+    - selftests: mlxsw: tc_police_scale: Make test more robust
+    - pinctrl: sunxi: Use unique lockdep classes for IRQs
+    - igc: igc_write_phy_reg_gpy: drop premature return
+    - ibmvnic: free reset-work-item when flushing
+    - memfd: fix F_SEAL_WRITE after shmem huge page allocated
+    - s390/extable: fix exception table sorting
+    - sched: Fix yet more sched_fork() races
+    - arm64: dts: juno: Remove GICv2m dma-range
+    - iommu/amd: Fix I/O page table memory leak
+    - MIPS: ralink: mt7621: do memory detection on KSEG1
+    - ARM: dts: switch timer config to common devkit8000 devicetree
+    - ARM: dts: Use 32KiHz oscillator on devkit8000
+    - soc: fsl: guts: Revert commit 3c0d64e867ed
+    - soc: fsl: guts: Add a missing memory allocation failure check
+    - soc: fsl: qe: Check of ioremap return value
+    - netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
+    - ARM: tegra: Move panels to AUX bus
+    - can: etas_es58x: change opened_channel_cnt's type from atomic_t to u8
+    - net: stmmac: enhance XDP ZC driver level switching performance
+    - net: stmmac: only enable DMA interrupts when ready
+    - ibmvnic: initialize rc before completing wait
+    - ibmvnic: define flush_reset_queue helper
+    - ibmvnic: complete init_done on transport events
+    - net: chelsio: cxgb3: check the return value of pci_find_capability()
+    - net: sparx5: Fix add vlan when invalid operation
+    - iavf: Refactor iavf state machine tracking
+    - iavf: Add __IAVF_INIT_FAILED state
+    - iavf: Combine init and watchdog state machines
+    - iavf: Add trace while removing device
+    - iavf: Rework mutexes for better synchronisation
+    - iavf: Add helper function to go from pci_dev to adapter
+    - iavf: Fix kernel BUG in free_msi_irqs
+    - iavf: Add waiting so the port is initialized in remove
+    - iavf: Fix init state closure on remove
+    - iavf: Fix locking for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS
+    - iavf: Fix race in init state
+    - iavf: Fix __IAVF_RESETTING state usage
+    - drm/i915/guc/slpc: Correct the param count for unset param
+    - drm/bridge: ti-sn65dsi86: Properly undo autosuspend
+    - e1000e: Fix possible HW unit hang after an s0ix exit
+    - MIPS: ralink: mt7621: use bitwise NOT instead of logical
+    - nl80211: Handle nla_memdup failures in handle_nan_filter
+    - drm/amdgpu: fix suspend/resume hang regression
+    - net: dcb: disable softirqs in dcbnl_flush_dev()
+    - selftests: mlxsw: resource_scale: Fix return value
+    - net: stmmac: perserve TX and RX coalesce value during XDP setup
+    - iavf: do not override the adapter state in the watchdog task (again)
+    - iavf: missing unlocks in iavf_watchdog_task()
+    - MAINTAINERS: adjust file entry for of_net.c after movement
+    - Input: elan_i2c - move regulator_[en|dis]able() out of
+      elan_[en|dis]able_power()
+    - Input: elan_i2c - fix regulator enable count imbalance after suspend/resume
+    - Input: samsung-keypad - properly state IOMEM dependency
+    - HID: add mapping for KEY_DICTATE
+    - HID: add mapping for KEY_ALL_APPLICATIONS
+    - tracing/histogram: Fix sorting on old "cpu" value
+    - tracing: Fix return value of __setup handlers
+    - btrfs: fix lost prealloc extents beyond eof after full fsync
+    - btrfs: fix relocation crash due to premature return from
+      btrfs_commit_transaction()
+    - btrfs: do not WARN_ON() if we have PageError set
+    - btrfs: qgroup: fix deadlock between rescan worker and remove qgroup
+    - btrfs: add missing run of delayed items after unlink during log replay
+    - btrfs: do not start relocation until in progress drops are done
+    - Revert "xfrm: xfrm_state_mtu should return at least 1280 for ipv6"
+    - proc: fix documentation and description of pagemap
+    - KVM: x86/mmu: Passing up the error state of mmu_alloc_shadow_roots()
+    - hamradio: fix macro redefine warning
+    - Linux 5.15.27
+    - [Config] updateconfigs
+
+  * devices on thunderbolt dock are not recognized on adl-p platform
+    (LP: #1955016)
+    - thunderbolt: Tear down existing tunnels when resuming from hibernate
+    - thunderbolt: Runtime resume USB4 port when retimers are scanned
+    - thunderbolt: Do not allow subtracting more NFC credits than configured
+    - thunderbolt: Do not program path HopIDs for USB4 routers
+    - thunderbolt: Add debug logging of DisplayPort resource allocation
+
+  * MT7921[14c3:7961] ASPM is disabled and it affects power consumption
+    (LP: #1955882)
+    - mt76: mt7921: enable aspm by default
+
+  * Add proper runtime PM support to Realtek PCIe cardreader (LP: #1963615)
+    - mmc: rtsx: Use pm_runtime_{get, put}() to handle runtime PM
+    - misc: rtsx: Rework runtime power management flow
+    - misc: rtsx: Cleanup power management ops
+    - misc: rtsx: Quiesce rts5249 on system suspend
+    - mmc: rtsx: Let MMC core handle runtime PM
+    - misc: rtsx: conditionally build rtsx_pm_power_saving()
+    - misc: rtsx: rts522a rts5228 rts5261 support Runtime PM
+    - mmc: rtsx: Fix build errors/warnings for unused variable
+    - mmc: rtsx: add 74 Clocks in power on flow
+
+  * [22.04 FEAT] In-kernel crypto: SIMD implementation of chacha20
+    (LP: #1853152)
+    - s390/crypto: add SIMD implementation for ChaCha20
+    - s390/crypto: fix compile error for ChaCha20 module
+
+  * Add ConnectX7 support and bug fixes  to Jammy (LP: #1962185)
+    - IB/mlx5: Expose NDR speed through MAD
+
+  * INVALID or PRIVATE BUG (LP: #1959890)
+    - [Config] Deactivate CONFIG_QETH_OSX kernel config option
+
+  * Move virtual graphics drivers from linux-modules-extra to linux-modules
+    (LP: #1960633)
+    - [Packaging] Move VM DRM drivers into modules
+
+  * Not able to enter s2idle state on AMD platforms (LP: #1961121)
+    - HID: amd_sfh: Handle amd_sfh work buffer in PM ops
+    - HID: amd_sfh: Disable the interrupt for all command
+    - HID: amd_sfh: Add functionality to clear interrupts
+    - HID: amd_sfh: Add interrupt handler to process interrupts
+
+  * INVALID or PRIVATE BUG (LP: #1960580)
+    - s390/kexec_file: move kernel image size check
+    - s390: support command lines longer than 896 bytes
+
+  * [UBUNTU 20.04] kernel: Add support for CPU-MF counter second version 7
+    (LP: #1960182)
+    - s390/cpumf: Support for CPU Measurement Facility CSVN 7
+    - s390/cpumf: Support for CPU Measurement Sampling Facility LS bit
+
+  * [SRU]PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is
+    enabled by IOMMU (LP: #1937295)
+    - PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled
+      by IOMMU
+
+  * Jammy update: v5.15.26 upstream stable release (LP: #1963891)
+    - mm/filemap: Fix handling of THPs in generic_file_buffered_read()
+    - cgroup/cpuset: Fix a race between cpuset_attach() and cpu hotplug
+    - cgroup-v1: Correct privileges check in release_agent writes
+    - x86/ptrace: Fix xfpregs_set()'s incorrect xmm clearing
+    - btrfs: tree-checker: check item_size for inode_item
+    - btrfs: tree-checker: check item_size for dev_item
+    - clk: jz4725b: fix mmc0 clock gating
+    - io_uring: don't convert to jiffies for waiting on timeouts
+    - io_uring: disallow modification of rsrc_data during quiesce
+    - selinux: fix misuse of mutex_is_locked()
+    - vhost/vsock: don't check owner in vhost_vsock_stop() while releasing
+    - parisc/unaligned: Fix fldd and fstd unaligned handlers on 32-bit kernel
+    - parisc/unaligned: Fix ldw() and stw() unalignment handlers
+    - KVM: x86/mmu: make apf token non-zero to fix bug
+    - drm/amd/display: Protect update_bw_bounding_box FPU code.
+    - drm/amd/pm: fix some OEM SKU specific stability issues
+    - drm/amd: Check if ASPM is enabled from PCIe subsystem
+    - drm/amdgpu: disable MMHUB PG for Picasso
+    - drm/amdgpu: do not enable asic reset for raven2
+    - drm/i915: Widen the QGV point mask
+    - drm/i915: Correctly populate use_sagv_wm for all pipes
+    - drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV
+    - sr9700: sanity check for packet length
+    - USB: zaurus: support another broken Zaurus
+    - CDC-NCM: avoid overflow in sanity checking
+    - netfilter: xt_socket: fix a typo in socket_mt_destroy()
+    - netfilter: xt_socket: missing ifdef CONFIG_IP6_NF_IPTABLES dependency
+    - tee: export teedev_open() and teedev_close_context()
+    - optee: use driver internal tee_context for some rpc
+    - ping: remove pr_err from ping_lookup
+    - Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
+    - gpu: host1x: Always return syncpoint value when waiting
+    - perf evlist: Fix failed to use cpu list for uncore events
+    - perf data: Fix double free in perf_session__delete()
+    - mptcp: fix race in incoming ADD_ADDR option processing
+    - mptcp: add mibs counter for ignored incoming options
+    - selftests: mptcp: fix diag instability
+    - selftests: mptcp: be more conservative with cookie MPJ limits
+    - bnx2x: fix driver load from initrd
+    - bnxt_en: Fix active FEC reporting to ethtool
+    - bnxt_en: Fix offline ethtool selftest with RDMA enabled
+    - bnxt_en: Fix incorrect multicast rx mask setting when not requested
+    - hwmon: Handle failure to register sensor with thermal zone correctly
+    - net/mlx5: Fix tc max supported prio for nic mode
+    - ice: check the return of ice_ptp_gettimex64
+    - ice: initialize local variable 'tlv'
+    - net/mlx5: Update the list of the PCI supported devices
+    - bpf: Fix crash due to incorrect copy_map_value
+    - bpf: Do not try bpf_msg_push_data with len 0
+    - selftests: bpf: Check bpf_msg_push_data return value
+    - bpf: Fix a bpf_timer initialization issue
+    - bpf: Add schedule points in batch ops
+    - io_uring: add a schedule point in io_add_buffers()
+    - net: __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor friends
+    - nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
+    - tipc: Fix end of loop tests for list_for_each_entry()
+    - gso: do not skip outer ip header in case of ipip and net_failover
+    - net: mv643xx_eth: process retval from of_get_mac_address
+    - openvswitch: Fix setting ipv6 fields causing hw csum failure
+    - drm/edid: Always set RGB444
+    - net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
+    - drm/vc4: crtc: Fix runtime_pm reference counting
+    - drm/i915/dg2: Print PHY name properly on calibration error
+    - net/sched: act_ct: Fix flow table lookup after ct clear or switching zones
+    - net: ll_temac: check the return value of devm_kmalloc()
+    - net: Force inlining of checksum functions in net/checksum.h
+    - netfilter: nf_tables: unregister flowtable hooks on netns exit
+    - nfp: flower: Fix a potential leak in nfp_tunnel_add_shared_mac()
+    - net: mdio-ipq4019: add delay after clock enable
+    - netfilter: nf_tables: fix memory leak during stateful obj update
+    - net/smc: Use a mutex for locking "struct smc_pnettable"
+    - surface: surface3_power: Fix battery readings on batteries without a serial
+      number
+    - udp_tunnel: Fix end of loop test in udp_tunnel_nic_unregister()
+    - net/mlx5: DR, Cache STE shadow memory
+    - ibmvnic: schedule failover only if vioctl fails
+    - net/mlx5: DR, Don't allow match on IP w/o matching on full
+      ethertype/ip_version
+    - net/mlx5: Fix possible deadlock on rule deletion
+    - net/mlx5: Fix wrong limitation of metadata match on ecpf
+    - net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
+    - net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
+    - net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
+    - net/mlx5: Update log_max_qp value to be 17 at most
+    - spi: spi-zynq-qspi: Fix a NULL pointer dereference in
+      zynq_qspi_exec_mem_op()
+    - gpio: rockchip: Reset int_bothedge when changing trigger
+    - regmap-irq: Update interrupt clear register for proper reset
+    - net-timestamp: convert sk->sk_tskey to atomic_t
+    - RDMA/rtrs-clt: Fix possible double free in error case
+    - RDMA/rtrs-clt: Move free_permit from free_clt to rtrs_clt_close
+    - bnxt_en: Increase firmware message response DMA wait time
+    - configfs: fix a race in configfs_{,un}register_subsystem()
+    - RDMA/ib_srp: Fix a deadlock
+    - tracing: Dump stacktrace trigger to the corresponding instance
+    - tracing: Have traceon and traceoff trigger honor the instance
+    - iio:imu:adis16480: fix buffering for devices with no burst mode
+    - iio: adc: men_z188_adc: Fix a resource leak in an error handling path
+    - iio: adc: tsc2046: fix memory corruption by preventing array overflow
+    - iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
+    - iio: accel: fxls8962af: add padding to regmap for SPI
+    - iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
+    - iio: Fix error handling for PM
+    - sc16is7xx: Fix for incorrect data being transmitted
+    - ata: pata_hpt37x: disable primary channel on HPT371
+    - Revert "USB: serial: ch341: add new Product ID for CH341A"
+    - usb: gadget: rndis: add spinlock for rndis response list
+    - USB: gadget: validate endpoint index for xilinx udc
+    - tracefs: Set the group ownership in apply_options() not parse_options()
+    - USB: serial: option: add support for DW5829e
+    - USB: serial: option: add Telit LE910R1 compositions
+    - usb: dwc2: drd: fix soft connect when gadget is unconfigured
+    - usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail
+    - usb: dwc3: pci: Fix Bay Trail phy GPIO mappings
+    - usb: dwc3: gadget: Let the interrupt handler disable bottom halves.
+    - xhci: re-initialize the HC during resume if HCE was set
+    - xhci: Prevent futile URB re-submissions due to incorrect return value.
+    - nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
+    - mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
+    - driver core: Free DMA range map when device is released
+    - btrfs: prevent copying too big compressed lzo segment
+    - RDMA/cma: Do not change route.addr.src_addr outside state checks
+    - thermal: int340x: fix memory leak in int3400_notify()
+    - staging: fbtft: fb_st7789v: reset display before initialization
+    - tps6598x: clear int mask on probe failure
+    - IB/qib: Fix duplicate sysfs directory name
+    - riscv: fix nommu_k210_sdcard_defconfig
+    - riscv: fix oops caused by irqsoff latency tracer
+    - tty: n_gsm: fix encoding of control signal octet bit DV
+    - tty: n_gsm: fix proper link termination after failed open
+    - tty: n_gsm: fix NULL pointer access due to DLCI release
+    - tty: n_gsm: fix wrong tty control line for flow control
+    - tty: n_gsm: fix wrong modem processing in convergence layer type 2
+    - tty: n_gsm: fix deadlock in gsmtty_open()
+    - pinctrl: fix loop in k210_pinconf_get_drive()
+    - pinctrl: k210: Fix bias-pull-up
+    - gpio: tegra186: Fix chip_data type confusion
+    - memblock: use kfree() to release kmalloced memblock regions
+    - ice: Fix race conditions between virtchnl handling and VF ndo ops
+    - ice: fix concurrent reset and removal of VFs
+    - Linux 5.15.26
+
+  * Jammy update: v5.15.25 upstream stable release (LP: #1963890)
+    - drm/nouveau/pmu/gm200-: use alternate falcon reset sequence
+    - fs/proc: task_mmu.c: don't read mapcount for migration entry
+    - btrfs: zoned: cache reported zone during mount
+    - HID:Add support for UGTABLET WP5540
+    - Revert "svm: Add warning message for AVIC IPI invalid target"
+    - parisc: Show error if wrong 32/64-bit compiler is being used
+    - serial: parisc: GSC: fix build when IOSAPIC is not set
+    - parisc: Drop __init from map_pages declaration
+    - parisc: Fix data TLB miss in sba_unmap_sg
+    - parisc: Fix sglist access in ccio-dma.c
+    - mmc: block: fix read single on recovery logic
+    - mm: don't try to NUMA-migrate COW pages that have other uses
+    - HID: amd_sfh: Add illuminance mask to limit ALS max value
+    - HID: i2c-hid: goodix: Fix a lockdep splat
+    - HID: amd_sfh: Increase sensor command timeout
+    - HID: amd_sfh: Correct the structure field name
+    - PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA
+      topology
+    - parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()
+    - btrfs: send: in case of IO error log it
+    - platform/x86: touchscreen_dmi: Add info for the RWC NANOTE P8 AY07J 2-in-1
+    - platform/x86: ISST: Fix possible circular locking dependency detected
+    - kunit: tool: Import missing importlib.abc
+    - selftests: rtc: Increase test timeout so that all tests run
+    - kselftest: signal all child processes
+    - net: ieee802154: at86rf230: Stop leaking skb's
+    - selftests/zram: Skip max_comp_streams interface on newer kernel
+    - selftests/zram01.sh: Fix compression ratio calculation
+    - selftests/zram: Adapt the situation that /dev/zram0 is being used
+    - selftests: openat2: Print also errno in failure messages
+    - selftests: openat2: Add missing dependency in Makefile
+    - selftests: openat2: Skip testcases that fail with EOPNOTSUPP
+    - selftests: skip mincore.check_file_mmap when fs lacks needed support
+    - ax25: improve the incomplete fix to avoid UAF and NPD bugs
+    - pinctrl: bcm63xx: fix unmet dependency on REGMAP for GPIO_REGMAP
+    - vfs: make freeze_super abort when sync_filesystem returns error
+    - quota: make dquot_quota_sync return errors from ->sync_fs
+    - scsi: pm80xx: Fix double completion for SATA devices
+    - kselftest: Fix vdso_test_abi return status
+    - scsi: core: Reallocate device's budget map on queue depth change
+    - scsi: pm8001: Fix use-after-free for aborted TMF sas_task
+    - scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task
+    - drm/amd: Warn users about potential s0ix problems
+    - nvme: fix a possible use-after-free in controller reset during load
+    - nvme-tcp: fix possible use-after-free in transport error_recovery work
+    - nvme-rdma: fix possible use-after-free in transport error_recovery work
+    - net: sparx5: do not refer to skb after passing it on
+    - drm/amd: add support to check whether the system is set to s3
+    - drm/amd: Only run s3 or s0ix if system is configured properly
+    - drm/amdgpu: fix logic inversion in check
+    - x86/Xen: streamline (and fix) PV CPU enumeration
+    - Revert "module, async: async_synchronize_full() on module init iff async is
+      used"
+    - gcc-plugins/stackleak: Use noinstr in favor of notrace
+    - random: wake up /dev/random writers after zap
+    - KVM: x86/xen: Fix runstate updates to be atomic when preempting vCPU
+    - KVM: x86: nSVM/nVMX: set nested_run_pending on VM entry which is a result of
+      RSM
+    - KVM: x86: SVM: don't passthrough SMAP/SMEP/PKE bits in !NPT && !gCR0.PG case
+    - KVM: x86: nSVM: fix potential NULL derefernce on nested migration
+    - KVM: x86: nSVM: mark vmcb01 as dirty when restoring SMM saved state
+    - iwlwifi: fix use-after-free
+    - drm/radeon: Fix backlight control on iMac 12,1
+    - drm/atomic: Don't pollute crtc_state->mode_blob with error pointers
+    - drm/amd/pm: correct the sequence of sending gpu reset msg
+    - drm/amdgpu: skipping SDMA hw_init and hw_fini for S0ix.
+    - drm/i915/opregion: check port number bounds for SWSCI display power state
+    - drm/i915: Fix dbuf slice config lookup
+    - drm/i915: Fix mbus join config lookup
+    - vsock: remove vsock from connected table when connect is interrupted by a
+      signal
+    - drm/cma-helper: Set VM_DONTEXPAND for mmap
+    - drm/i915/gvt: Make DRM_I915_GVT depend on X86
+    - drm/i915/ttm: tweak priority hint selection
+    - iwlwifi: pcie: fix locking when "HW not ready"
+    - iwlwifi: pcie: gen2: fix locking when "HW not ready"
+    - iwlwifi: mvm: don't send SAR GEO command for 3160 devices
+    - selftests: netfilter: fix exit value for nft_concat_range
+    - netfilter: nft_synproxy: unregister hooks on init error path
+    - selftests: netfilter: disable rp_filter on router
+    - ipv4: fix data races in fib_alias_hw_flags_set
+    - ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
+    - ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
+    - ipv6: per-netns exclusive flowlabel checks
+    - Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
+    - mac80211: mlme: check for null after calling kmemdup
+    - brcmfmac: firmware: Fix crash in brcm_alt_fw_path
+    - cfg80211: fix race in netlink owner interface destruction
+    - net: dsa: lan9303: fix reset on probe
+    - net: dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
+    - net: dsa: lantiq_gswip: fix use after free in gswip_remove()
+    - net: dsa: lan9303: handle hwaccel VLAN tags
+    - net: dsa: lan9303: add VLAN IDs to master device
+    - net: ieee802154: ca8210: Fix lifs/sifs periods
+    - ping: fix the dif and sdif check in ping_lookup
+    - bonding: force carrier update when releasing slave
+    - drop_monitor: fix data-race in dropmon_net_event / trace_napi_poll_hit
+    - net_sched: add __rcu annotation to netdev->qdisc
+    - bonding: fix data-races around agg_select_timer
+    - libsubcmd: Fix use-after-free for realloc(..., 0)
+    - net/smc: Avoid overwriting the copies of clcsock callback functions
+    - net: phy: mediatek: remove PHY mode check on MT7531
+    - atl1c: fix tx timeout after link flap on Mikrotik 10/25G NIC
+    - tipc: fix wrong publisher node address in link publications
+    - dpaa2-switch: fix default return of dpaa2_switch_flower_parse_mirror_key
+    - dpaa2-eth: Initialize mutex used in one step timestamping path
+    - net: bridge: multicast: notify switchdev driver whenever MC processing gets
+      disabled
+    - perf bpf: Defer freeing string after possible strlen() on it
+    - selftests/exec: Add non-regular to TEST_GEN_PROGS
+    - arm64: Correct wrong label in macro __init_el2_gicv3
+    - ALSA: usb-audio: revert to IMPLICIT_FB_FIXED_DEV for M-Audio FastTrack Ultra
+    - ALSA: hda/realtek: Add quirk for Legion Y9000X 2019
+    - ALSA: hda/realtek: Fix deadlock by COEF mutex
+    - ALSA: hda: Fix regression on forced probe mask option
+    - ALSA: hda: Fix missing codec probe on Shenker Dock 15
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_range()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_sx()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_xr_sx()
+    - cifs: fix set of group SID via NTSD xattrs
+    - powerpc/603: Fix boot failure with DEBUG_PAGEALLOC and KFENCE
+    - powerpc/lib/sstep: fix 'ptesync' build error
+    - mtd: rawnand: gpmi: don't leak PM reference in error path
+    - smb3: fix snapshot mount option
+    - tipc: fix wrong notification node addresses
+    - scsi: ufs: Remove dead code
+    - scsi: ufs: Fix a deadlock in the error handler
+    - ASoC: tas2770: Insert post reset delay
+    - ASoC: qcom: Actually clear DMA interrupt register for HDMI
+    - block/wbt: fix negative inflight counter when remove scsi device
+    - NFS: Remove an incorrect revalidation in nfs4_update_changeattr_locked()
+    - NFS: LOOKUP_DIRECTORY is also ok with symlinks
+    - NFS: Do not report writeback errors in nfs_getattr()
+    - tty: n_tty: do not look ahead for EOL character past the end of the buffer
+    - block: fix surprise removal for drivers calling blk_set_queue_dying
+    - mtd: rawnand: qcom: Fix clock sequencing in qcom_nandc_probe()
+    - mtd: parsers: qcom: Fix kernel panic on skipped partition
+    - mtd: parsers: qcom: Fix missing free for pparts in cleanup
+    - mtd: phram: Prevent divide by zero bug in phram_setup()
+    - mtd: rawnand: brcmnand: Fixed incorrect sub-page ECC status
+    - HID: elo: fix memory leak in elo_probe
+    - mtd: rawnand: ingenic: Fix missing put_device in ingenic_ecc_get
+    - Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj
+    - KVM: x86/pmu: Refactoring find_arch_event() to pmc_perf_hw_id()
+    - KVM: x86/pmu: Don't truncate the PerfEvtSeln MSR when creating a perf event
+    - KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW
+    - ARM: OMAP2+: hwmod: Add of_node_put() before break
+    - ARM: OMAP2+: adjust the location of put_device() call in omapdss_init_of
+    - phy: usb: Leave some clocks running during suspend
+    - staging: vc04_services: Fix RCU dereference check
+    - phy: phy-mtk-tphy: Fix duplicated argument in phy-mtk-tphy
+    - irqchip/sifive-plic: Add missing thead,c900-plic match string
+    - x86/bug: Merge annotate_reachable() into _BUG_FLAGS() asm
+    - netfilter: conntrack: don't refresh sctp entries in closed state
+    - ksmbd: fix same UniqueId for dot and dotdot entries
+    - ksmbd: don't align last entry offset in smb2 query directory
+    - arm64: dts: meson-gx: add ATF BL32 reserved-memory region
+    - arm64: dts: meson-g12: add ATF BL32 reserved-memory region
+    - arm64: dts: meson-g12: drop BL32 region from SEI510/SEI610
+    - pidfd: fix test failure due to stack overflow on some arches
+    - selftests: fixup build warnings in pidfd / clone3 tests
+    - mm: io_uring: allow oom-killer from io_uring_setup
+    - kconfig: let 'shell' return enough output for deep path names
+    - ata: libata-core: Disable TRIM on M88V29
+    - soc: aspeed: lpc-ctrl: Block error printing on probe defer cases
+    - xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create
+    - drm/rockchip: dw_hdmi: Do not leave clock enabled in error case
+    - tracing: Fix tp_printk option related with tp_printk_stop_on_boot
+    - display/amd: decrease message verbosity about watermarks table failure
+    - drm/amd/display: Cap pflip irqs per max otg number
+    - drm/amd/display: fix yellow carp wm clamping
+    - net: usb: qmi_wwan: Add support for Dell DW5829e
+    - net: macb: Align the dma and coherent dma masks
+    - kconfig: fix failing to generate auto.conf
+    - scsi: lpfc: Fix pt2pt NVMe PRLI reject LOGO loop
+    - EDAC: Fix calculation of returned address and next offset in
+      edac_align_ptr()
+    - ucounts: Handle wrapping in is_ucounts_overlimit
+    - ucounts: In set_cred_ucounts assume new->ucounts is non-NULL
+    - ucounts: Base set_cred_ucounts changes on the real user
+    - ucounts: Enforce RLIMIT_NPROC not RLIMIT_NPROC+1
+    - lib/iov_iter: initialize "flags" in new pipe_buffer
+    - rlimit: Fix RLIMIT_NPROC enforcement failure caused by capability calls in
+      set_user
+    - ucounts: Move RLIMIT_NPROC handling after set_user
+    - net: sched: limit TC_ACT_REPEAT loops
+    - dmaengine: sh: rcar-dmac: Check for error num after setting mask
+    - dmaengine: stm32-dmamux: Fix PM disable depth imbalance in
+      stm32_dmamux_probe
+    - dmaengine: sh: rcar-dmac: Check for error num after dma_set_max_seg_size
+    - tests: fix idmapped mount_setattr test
+    - i2c: qcom-cci: don't delete an unregistered adapter
+    - i2c: qcom-cci: don't put a device tree node before i2c_add_adapter()
+    - dmaengine: ptdma: Fix the error handling path in pt_core_init()
+    - copy_process(): Move fd_install() out of sighand->siglock critical section
+    - scsi: qedi: Fix ABBA deadlock in qedi_process_tmf_resp() and
+      qedi_process_cmd_cleanup_resp()
+    - ice: enable parsing IPSEC SPI headers for RSS
+    - i2c: brcmstb: fix support for DSL and CM variants
+    - lockdep: Correct lock_classes index mapping
+    - Linux 5.15.25
+
+  * Jammy update: v5.15.24 upstream stable release (LP: #1963889)
+    - integrity: check the return value of audit_log_start()
+    - ima: fix reference leak in asymmetric_verify()
+    - ima: Remove ima_policy file before directory
+    - ima: Allow template selection with ima_template[_fmt]= after ima_hash=
+    - ima: Do not print policy rule with inactive LSM labels
+    - mmc: sdhci-of-esdhc: Check for error num after setting mask
+    - mmc: core: Wait for command setting 'Power Off Notification' bit to complete
+    - can: isotp: fix potential CAN frame reception race in isotp_rcv()
+    - can: isotp: fix error path in isotp_sendmsg() to unlock wait queue
+    - net: phy: marvell: Fix RGMII Tx/Rx delays setting in 88e1121-compatible PHYs
+    - net: phy: marvell: Fix MDI-x polarity setting in 88e1118-compatible PHYs
+    - NFS: Fix initialisation of nfs_client cl_flags field
+    - NFSD: Fix NFSv3 SETATTR/CREATE's handling of large file sizes
+    - NFSD: Fix ia_size underflow
+    - NFSD: Clamp WRITE offsets
+    - NFSD: Fix offset type in I/O trace points
+    - NFSD: Fix the behavior of READ near OFFSET_MAX
+    - thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume
+    - thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses
+    - thermal: int340x: Limit Kconfig to 64-bit
+    - thermal/drivers/int340x: Fix RFIM mailbox write commands
+    - tracing: Propagate is_signed to expression
+    - NFS: change nfs_access_get_cached to only report the mask
+    - NFSv4 only print the label when its queried
+    - nfs: nfs4clinet: check the return value of kstrdup()
+    - NFSv4.1: Fix uninitialised variable in devicenotify
+    - NFSv4 remove zero number of fs_locations entries error check
+    - NFSv4 store server support for fs_location attribute
+    - NFSv4.1 query for fs_location attr on a new file system
+    - NFSv4 expose nfs_parse_server_name function
+    - NFSv4 handle port presence in fs_location server string
+    - SUNRPC allow for unspecified transport time in rpc_clnt_add_xprt
+    - net/sunrpc: fix reference count leaks in rpc_sysfs_xprt_state_change
+    - sunrpc: Fix potential race conditions in rpc_sysfs_xprt_state_change()
+    - irqchip/realtek-rtl: Service all pending interrupts
+    - perf/x86/rapl: fix AMD event handling
+    - x86/perf: Avoid warning for Arch LBR without XSAVE
+    - sched: Avoid double preemption in __cond_resched_*lock*()
+    - drm/vc4: Fix deadlock on DSI device attach error
+    - drm: panel-orientation-quirks: Add quirk for the 1Netbook OneXPlayer
+    - net: sched: Clarify error message when qdisc kind is unknown
+    - powerpc/fixmap: Fix VM debug warning on unmap
+    - scsi: target: iscsi: Make sure the np under each tpg is unique
+    - scsi: ufs: ufshcd-pltfrm: Check the return value of devm_kstrdup()
+    - scsi: qedf: Add stag_work to all the vports
+    - scsi: qedf: Fix refcount issue when LOGO is received during TMF
+    - scsi: qedf: Change context reset messages to ratelimited
+    - scsi: pm8001: Fix bogus FW crash for maxcpus=1
+    - scsi: ufs: Use generic error code in ufshcd_set_dev_pwr_mode()
+    - scsi: ufs: Treat link loss as fatal error
+    - scsi: myrs: Fix crash in error case
+    - net: stmmac: reduce unnecessary wakeups from eee sw timer
+    - PM: hibernate: Remove register_nosave_region_late()
+    - drm/amd/display: Correct MPC split policy for DCN301
+    - usb: dwc2: gadget: don't try to disable ep0 in dwc2_hsotg_suspend
+    - perf: Always wake the parent event
+    - nvme-pci: add the IGNORE_DEV_SUBNQN quirk for Intel P4500/P4600 SSDs
+    - MIPS: Fix build error due to PTR used in more places
+    - net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
+    - KVM: eventfd: Fix false positive RCU usage warning
+    - KVM: nVMX: eVMCS: Filter out VM_EXIT_SAVE_VMX_PREEMPTION_TIMER
+    - KVM: nVMX: Also filter MSR_IA32_VMX_TRUE_PINBASED_CTLS when eVMCS
+    - KVM: SVM: Don't kill SEV guest if SMAP erratum triggers in usermode
+    - KVM: VMX: Set vmcs.PENDING_DBG.BS on #DB in STI/MOVSS blocking shadow
+    - KVM: x86: Report deprecated x87 features in supported CPUID
+    - riscv: fix build with binutils 2.38
+    - riscv: cpu-hotplug: clear cpu from numa map when teardown
+    - riscv: eliminate unreliable __builtin_frame_address(1)
+    - gfs2: Fix gfs2_release for non-writers regression
+    - ARM: dts: imx23-evk: Remove MX23_PAD_SSP1_DETECT from hog group
+    - ARM: dts: Fix boot regression on Skomer
+    - ARM: socfpga: fix missing RESET_CONTROLLER
+    - nvme-tcp: fix bogus request completion when failing to send AER
+    - ACPI/IORT: Check node revision for PMCG resources
+    - PM: s2idle: ACPI: Fix wakeup interrupts handling
+    - drm/amdgpu/display: change pipe policy for DCN 2.0
+    - drm/rockchip: vop: Correct RK3399 VOP register fields
+    - drm/i915: Allow !join_mbus cases for adlp+ dbuf configuration
+    - drm/i915: Populate pipe dbuf slices more accurately during readout
+    - ARM: dts: Fix timer regression for beagleboard revision c
+    - ARM: dts: meson: Fix the UART compatible strings
+    - ARM: dts: meson8: Fix the UART device-tree schema validation
+    - ARM: dts: meson8b: Fix the UART device-tree schema validation
+    - phy: broadcom: Kconfig: Fix PHY_BRCM_USB config option
+    - staging: fbtft: Fix error path in fbtft_driver_module_init()
+    - ARM: dts: imx6qdl-udoo: Properly describe the SD card detect
+    - phy: xilinx: zynqmp: Fix bus width setting for SGMII
+    - phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable()
+    - ARM: dts: imx7ulp: Fix 'assigned-clocks-parents' typo
+    - arm64: dts: imx8mq: fix mipi_csi bidirectional port numbers
+    - usb: f_fs: Fix use-after-free for epfile
+    - phy: dphy: Correct clk_pre parameter
+    - gpio: aggregator: Fix calling into sleeping GPIO controllers
+    - NFS: Don't overfill uncached readdir pages
+    - NFS: Don't skip directory entries when doing uncached readdir
+    - drm/vc4: hdmi: Allow DBLCLK modes even if horz timing is odd.
+    - misc: fastrpc: avoid double fput() on failed usercopy
+    - net: sparx5: Fix get_stat64 crash in tcpdump
+    - netfilter: ctnetlink: disable helper autoassign
+    - arm64: dts: meson-g12b-odroid-n2: fix typo 'dio2133'
+    - arm64: dts: meson-sm1-odroid: use correct enable-gpio pin for tf-io
+      regulator
+    - arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO domain for GPIOE_2
+    - arm64: dts: meson-sm1-odroid: fix boot loop after reboot
+    - ixgbevf: Require large buffers for build_skb on 82599VF
+    - drm/panel: simple: Assign data from panel_dpi_probe() correctly
+    - ACPI: PM: s2idle: Cancel wakeup before dispatching EC GPE
+    - gpiolib: Never return internal error codes to user space
+    - gpio: sifive: use the correct register to read output values
+    - fbcon: Avoid 'cap' set but not used warning
+    - bonding: pair enable_port with slave_arr_updates
+    - net: dsa: mv88e6xxx: don't use devres for mdiobus
+    - net: dsa: ar9331: register the mdiobus under devres
+    - net: dsa: bcm_sf2: don't use devres for mdiobus
+    - net: dsa: felix: don't use devres for mdiobus
+    - net: dsa: mt7530: fix kernel bug in mdiobus_free() when unbinding
+    - net: dsa: lantiq_gswip: don't use devres for mdiobus
+    - ipmr,ip6mr: acquire RTNL before calling ip[6]mr_free_table() on failure path
+    - nfp: flower: fix ida_idx not being released
+    - net: do not keep the dst cache when uncloning an skb dst and its metadata
+    - net: fix a memleak when uncloning an skb dst and its metadata
+    - veth: fix races around rq->rx_notify_masked
+    - net: mdio: aspeed: Add missing MODULE_DEVICE_TABLE
+    - tipc: rate limit warning for received illegal binding update
+    - net: amd-xgbe: disable interrupts during pci removal
+    - drm/amd/pm: fix hwmon node of power1_label create issue
+    - mptcp: netlink: process IPv6 addrs in creating listening sockets
+    - dpaa2-eth: unregister the netdev before disconnecting from the PHY
+    - ice: fix an error code in ice_cfg_phy_fec()
+    - ice: fix IPIP and SIT TSO offload
+    - ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
+    - ice: Avoid RTNL lock when re-creating auxiliary device
+    - net: mscc: ocelot: fix mutex lock error during ethtool stats read
+    - net: dsa: mv88e6xxx: fix use-after-free in mv88e6xxx_mdios_unregister
+    - vt_ioctl: fix array_index_nospec in vt_setactivate
+    - vt_ioctl: add array_index_nospec to VT_ACTIVATE
+    - n_tty: wake up poll(POLLRDNORM) on receiving data
+    - eeprom: ee1004: limit i2c reads to I2C_SMBUS_BLOCK_MAX
+    - usb: dwc2: drd: fix soft connect when gadget is unconfigured
+    - Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
+    - net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
+    - usb: ulpi: Move of_node_put to ulpi_dev_release
+    - usb: ulpi: Call of_node_put correctly
+    - usb: dwc3: gadget: Prevent core from processing stale TRBs
+    - usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
+    - USB: gadget: validate interface OS descriptor requests
+    - usb: gadget: rndis: check size of RNDIS_MSG_SET command
+    - usb: gadget: f_uac2: Define specific wTerminalType
+    - usb: raw-gadget: fix handling of dual-direction-capable endpoints
+    - USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
+    - USB: serial: option: add ZTE MF286D modem
+    - USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
+    - USB: serial: cp210x: add NCR Retail IO box id
+    - USB: serial: cp210x: add CPI Bulk Coin Recycler id
+    - speakup-dectlk: Restore pitch setting
+    - phy: ti: Fix missing sentinel for clk_div_table
+    - iio: buffer: Fix file related error handling in IIO_BUFFER_GET_FD_IOCTL
+    - mm: memcg: synchronize objcg lists with a dedicated spinlock
+    - seccomp: Invalidate seccomp mode to catch death failures
+    - signal: HANDLER_EXIT should clear SIGNAL_UNKILLABLE
+    - s390/cio: verify the driver availability for path_event call
+    - bus: mhi: pci_generic: Add mru_default for Foxconn SDX55
+    - bus: mhi: pci_generic: Add mru_default for Cinterion MV31-W
+    - hwmon: (dell-smm) Speed up setting of fan speed
+    - x86/sgx: Silence softlockup detection when releasing large enclaves
+    - Makefile.extrawarn: Move -Wunaligned-access to W=1
+    - scsi: lpfc: Remove NVMe support if kernel has NVME_FC disabled
+    - scsi: lpfc: Reduce log messages seen after firmware download
+    - MIPS: octeon: Fix missed PTR->PTR_WD conversion
+    - arm64: dts: imx8mq: fix lcdif port node
+    - perf: Fix list corruption in perf_cgroup_switch()
+    - iommu: Fix potential use-after-free during probe
+    - Linux 5.15.24
+
+  * Jammy update: v5.15.23 upstream stable release (LP: #1963888)
+    - moxart: fix potential use-after-free on remove path
+    - arm64: Add Cortex-A510 CPU part definition
+    - ksmbd: fix SMB 3.11 posix extension mount failure
+    - crypto: api - Move cryptomgr soft dependency into algapi
+    - Linux 5.15.23
+
+  * [22.04 FEAT] KVM: Enable storage key checking for intercepted instruction
+    handled by userspace (LP: #1933179)
+    - KVM: s390: gaccess: Refactor gpa and length calculation
+    - KVM: s390: gaccess: Refactor access address range check
+    - KVM: s390: gaccess: Cleanup access to guest pages
+    - s390/uaccess: introduce bit field for OAC specifier
+    - s390/uaccess: fix compile error
+    - s390/uaccess: Add copy_from/to_user_key functions
+    - KVM: s390: Honor storage keys when accessing guest memory
+    - KVM: s390: handle_tprot: Honor storage keys
+    - KVM: s390: selftests: Test TEST PROTECTION emulation
+    - KVM: s390: Add optional storage key checking to MEMOP IOCTL
+    - KVM: s390: Add vm IOCTL for key checked guest absolute memory access
+    - KVM: s390: Rename existing vcpu memop functions
+    - KVM: s390: Add capability for storage key extension of MEM_OP IOCTL
+    - KVM: s390: Update api documentation for memop ioctl
+    - KVM: s390: Clarify key argument for MEM_OP in api docs
+    - KVM: s390: Add missing vm MEM_OP size check
+
+  * CVE-2022-25636
+    - netfilter: nf_tables_offload: incorrect flow offload action array size
+
+  * ubuntu_kernel_selftests / ftrace:ftracetest do_softirq failure on Jammy
+    realtime (LP: #1959610)
+    - selftests/ftrace: Do not trace do_softirq because of PREEMPT_RT
+
+  * CVE-2022-0435
+    - tipc: improve size validations for received domain records
+
+  * CVE-2022-0516
+    - KVM: s390: Return error on SIDA memop on normal guest
+
+  * EDAC update for AMD Genoa support in 22.04 (LP: #1960362)
+    - EDAC: Add RDDR5 and LRDDR5 memory types
+    - EDAC/amd64: Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
+
+  * hwmon: k10temp updates for AMD Genoa in 22.04 (LP: #1960361)
+    - x86/amd_nb: Add AMD Family 19h Models (10h-1Fh) and (A0h-AFh) PCI IDs
+    - hwmon: (k10temp) Remove unused definitions
+    - hwmon: (k10temp) Support up to 12 CCDs on AMD Family of processors
+    - hwmon: (k10temp) Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
+
+  * [SRU][I/J/OEM-5.13/OEM-5.14] Add basic support of MT7922 (LP: #1958151)
+    - mt76: mt7921: Add mt7922 support
+    - mt76: mt7921: add support for PCIe ID 0x0608/0x0616
+    - mt76: mt7921: introduce 160 MHz channel bandwidth support
+
+  * Use EC GPE for s2idle wakeup on AMD platforms (LP: #1960771)
+    - ACPI: PM: Revert "Only mark EC GPE for wakeup on Intel systems"
+
+  * Update Broadcom Emulex FC HBA lpfc driver to 14.0.0.4 for Ubuntu 22.04
+    (LP: #1956982)
+    - scsi: lpfc: Change return code on I/Os received during link bounce
+    - scsi: lpfc: Fix NPIV port deletion crash
+    - scsi: lpfc: Adjust CMF total bytes and rxmonitor
+    - scsi: lpfc: Cap CMF read bytes to MBPI
+    - scsi: lpfc: Add additional debugfs support for CMF
+    - scsi: lpfc: Update lpfc version to 14.0.0.4
+
+  * Forward-port drm/i915 commits from oem-5.14 for Alder Lake S & P
+    (LP: #1960298)
+    - drm/i915/dmc: Update to DMC v2.12
+    - drm/i915/adlp/tc: Fix PHY connected check for Thunderbolt mode
+    - drm/i915/tc: Remove waiting for PHY complete during releasing ownership
+    - drm/i915/tc: Check for DP-alt, legacy sinks before taking PHY ownership
+    - drm/i915/tc: Add/use helpers to retrieve TypeC port properties
+    - drm/i915/tc: Don't keep legacy TypeC ports in connected state w/o a sink
+    - drm/i915/tc: Add a mode for the TypeC PHY's disconnected state
+    - drm/i915/tc: Refactor TC-cold block/unblock helpers
+    - drm/i915/tc: Avoid using legacy AUX PW in TBT mode
+    - drm/i915/icl/tc: Remove the ICL special casing during TC-cold blocking
+    - drm/i915/tc: Fix TypeC PHY connect/disconnect logic on ADL-P
+    - drm/i915/tc: Drop extra TC cold blocking from intel_tc_port_connected()
+    - drm/i915/tc: Fix system hang on ADL-P during TypeC PHY disconnect
+    - drm/i915/display/adlp: Disable underrun recovery
+    - drm/i915/adl_s: Remove require_force_probe protection
+    - drm/i915/adlp: Remove require_force_probe protection
+
+  * INVALID or PRIVATE BUG (LP: #1959735)
+    - KVM: s390: Simplify SIGP Set Arch handling
+    - KVM: s390: Add a routine for setting userspace CPU state
+
+  * Include the QCA WCN 6856 v2.1 support (LP: #1954938)
+    - SAUCE: ath11k: shrink TCSR read mask for WCN6855 hw2.1
+
+  * Jammy update: v5.15.22 upstream stable release (LP: #1960516)
+    - drm/i915: Disable DSB usage for now
+    - selinux: fix double free of cond_list on error paths
+    - audit: improve audit queue handling when "audit=1" on cmdline
+    - ipc/sem: do not sleep with a spin lock held
+    - spi: stm32-qspi: Update spi registering
+    - ASoC: hdmi-codec: Fix OOB memory accesses
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_volsw()
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_volsw_sx()
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_xr_sx()
+    - ALSA: usb-audio: Correct quirk for VF0770
+    - ALSA: hda: Fix UAF of leds class devs at unbinding
+    - ALSA: hda: realtek: Fix race at concurrent COEF updates
+    - ALSA: hda/realtek: Add quirk for ASUS GU603
+    - ALSA: hda/realtek: Add missing fixup-model entry for Gigabyte X570 ALC1220
+      quirks
+    - ALSA: hda/realtek: Fix silent output on Gigabyte X570S Aorus Master (newer
+      chipset)
+    - ALSA: hda/realtek: Fix silent output on Gigabyte X570 Aorus Xtreme after
+      reboot from Windows
+    - btrfs: don't start transaction for scrub if the fs is mounted read-only
+    - btrfs: fix deadlock between quota disable and qgroup rescan worker
+    - btrfs: fix use-after-free after failure to create a snapshot
+    - Revert "fs/9p: search open fids first"
+    - drm/nouveau: fix off by one in BIOS boundary checking
+    - drm/i915/adlp: Fix TypeC PHY-ready status readout
+    - drm/amd/pm: correct the MGpuFanBoost support for Beige Goby
+    - drm/amd/display: watermark latencies is not enough on DCN31
+    - drm/amd/display: Force link_rate as LINK_RATE_RBR2 for 2018 15" Apple Retina
+      panels
+    - nvme-fabrics: fix state check in nvmf_ctlr_matches_baseopts()
+    - mm/debug_vm_pgtable: remove pte entry from the page table
+    - mm/pgtable: define pte_index so that preprocessor could recognize it
+    - mm/kmemleak: avoid scanning potential huge holes
+    - block: bio-integrity: Advance seed correctly for larger interval sizes
+    - dma-buf: heaps: Fix potential spectre v1 gadget
+    - IB/hfi1: Fix AIP early init panic
+    - Revert "fbcon: Disable accelerated scrolling"
+    - fbcon: Add option to enable legacy hardware acceleration
+    - mptcp: fix msk traversal in mptcp_nl_cmd_set_flags()
+    - Revert "ASoC: mediatek: Check for error clk pointer"
+    - KVM: arm64: Avoid consuming a stale esr value when SError occur
+    - KVM: arm64: Stop handle_exit() from handling HVC twice when an SError occurs
+    - RDMA/cma: Use correct address when leaving multicast group
+    - RDMA/ucma: Protect mc during concurrent multicast leaves
+    - RDMA/siw: Fix refcounting leak in siw_create_qp()
+    - IB/rdmavt: Validate remote_addr during loopback atomic tests
+    - RDMA/siw: Fix broken RDMA Read Fence/Resume logic.
+    - RDMA/mlx4: Don't continue event handler after memory allocation failure
+    - ALSA: usb-audio: initialize variables that could ignore errors
+    - ALSA: hda: Fix signedness of sscanf() arguments
+    - ALSA: hda: Skip codec shutdown in case the codec is not registered
+    - iommu/vt-d: Fix potential memory leak in intel_setup_irq_remapping()
+    - iommu/amd: Fix loop timeout issue in iommu_ga_log_enable()
+    - spi: bcm-qspi: check for valid cs before applying chip select
+    - spi: mediatek: Avoid NULL pointer crash in interrupt
+    - spi: meson-spicc: add IRQ check in meson_spicc_probe
+    - spi: uniphier: fix reference count leak in uniphier_spi_probe()
+    - IB/hfi1: Fix tstats alloc and dealloc
+    - IB/cm: Release previously acquired reference counter in the cm_id_priv
+    - net: ieee802154: hwsim: Ensure proper channel selection at probe time
+    - net: ieee802154: mcr20a: Fix lifs/sifs periods
+    - net: ieee802154: ca8210: Stop leaking skb's
+    - netfilter: nft_reject_bridge: Fix for missing reply from prerouting
+    - net: ieee802154: Return meaningful error codes from the netlink helpers
+    - net/smc: Forward wakeup to smc socket waitqueue after fallback
+    - net: stmmac: dwmac-visconti: No change to ETHER_CLOCK_SEL for unexpected
+      speed request.
+    - net: stmmac: properly handle with runtime pm in stmmac_dvr_remove()
+    - net: macsec: Fix offload support for NETDEV_UNREGISTER event
+    - net: macsec: Verify that send_sci is on when setting Tx sci explicitly
+    - net: stmmac: dump gmac4 DMA registers correctly
+    - net: stmmac: ensure PTP time register reads are consistent
+    - drm/kmb: Fix for build errors with Warray-bounds
+    - drm/i915/overlay: Prevent divide by zero bugs in scaling
+    - drm/amd: avoid suspend on dGPUs w/ s2idle support when runtime PM enabled
+    - ASoC: fsl: Add missing error handling in pcm030_fabric_probe
+    - ASoC: xilinx: xlnx_formatter_pcm: Make buffer bytes multiple of period bytes
+    - ASoC: simple-card: fix probe failure on platform component
+    - ASoC: cpcap: Check for NULL pointer after calling of_get_child_by_name
+    - ASoC: max9759: fix underflow in speaker_gain_control_put()
+    - ASoC: codecs: wcd938x: fix incorrect used of portid
+    - ASoC: codecs: lpass-rx-macro: fix sidetone register offsets
+    - ASoC: codecs: wcd938x: fix return value of mixer put function
+    - pinctrl: sunxi: Fix H616 I2S3 pin data
+    - pinctrl: intel: Fix a glitch when updating IRQ flags on a preconfigured line
+    - pinctrl: intel: fix unexpected interrupt
+    - pinctrl: bcm2835: Fix a few error paths
+    - scsi: bnx2fc: Make bnx2fc_recv_frame() mp safe
+    - nfsd: nfsd4_setclientid_confirm mistakenly expires confirmed client.
+    - gve: fix the wrong AdminQ buffer queue index check
+    - bpf: Use VM_MAP instead of VM_ALLOC for ringbuf
+    - selftests/exec: Remove pipe from TEST_GEN_FILES
+    - selftests: futex: Use variable MAKE instead of make
+    - tools/resolve_btfids: Do not print any commands when building silently
+    - e1000e: Separate ADP board type from TGP
+    - rtc: cmos: Evaluate century appropriate
+    - kvm: add guest_state_{enter,exit}_irqoff()
+    - kvm/arm64: rework guest entry logic
+    - perf: Copy perf_event_attr::sig_data on modification
+    - perf stat: Fix display of grouped aliased events
+    - perf/x86/intel/pt: Fix crash with stop filters in single-range mode
+    - x86/perf: Default set FREEZE_ON_SMI for all
+    - EDAC/altera: Fix deferred probing
+    - EDAC/xgene: Fix deferred probing
+    - ext4: prevent used blocks from being allocated during fast commit replay
+    - ext4: modify the logic of ext4_mb_new_blocks_simple
+    - ext4: fix error handling in ext4_restore_inline_data()
+    - ext4: fix error handling in ext4_fc_record_modified_inode()
+    - ext4: fix incorrect type issue during replay_del_range
+    - net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY
+    - cgroup/cpuset: Fix "suspicious RCU usage" lockdep warning
+    - tools include UAPI: Sync sound/asound.h copy with the kernel sources
+    - gpio: idt3243x: Fix an ignored error return from platform_get_irq()
+    - gpio: mpc8xxx: Fix an ignored error return from platform_get_irq()
+    - selftests: nft_concat_range: add test for reload with no element add/del
+    - selftests: netfilter: check stateless nat udp checksum fixup
+    - Linux 5.15.22
+    - [Config] disable FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+
+  * Jammy update: v5.15.21 upstream stable release (LP: #1960515)
+    - Revert "drm/vc4: hdmi: Make sure the device is powered with CEC"
+    - Revert "drm/vc4: hdmi: Make sure the device is powered with CEC" again
+    - Linux 5.15.21
+
+  * Jammy update: v5.15.20 upstream stable release (LP: #1960509)
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Add handshake with the CSME to
+      support S0ix""
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Add polling mechanism to indicate
+      CSME DPG exit""
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Additional PHY power saving in S0ix""
+    - PCI: pciehp: Fix infinite loop in IRQ handler upon power fault
+    - selftests: mptcp: fix ipv6 routing setup
+    - net: ipa: use a bitmap for endpoint replenish_enabled
+    - net: ipa: prevent concurrent replenish
+    - drm/vc4: hdmi: Make sure the device is powered with CEC
+    - cgroup-v1: Require capabilities to set release_agent
+    - Revert "mm/gup: small refactoring: simplify try_grab_page()"
+    - ovl: don't fail copy up if no fileattr support on upper
+    - lockd: fix server crash on reboot of client holding lock
+    - lockd: fix failure to cleanup client locks
+    - net/mlx5e: IPsec: Fix tunnel mode crypto offload for non TCP/UDP traffic
+    - net/mlx5: Bridge, take rtnl lock in init error handler
+    - net/mlx5: Bridge, ensure dev_name is null-terminated
+    - net/mlx5e: Fix handling of wrong devices during bond netevent
+    - net/mlx5: Use del_timer_sync in fw reset flow of halting poll
+    - net/mlx5e: Fix module EEPROM query
+    - net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
+    - net/mlx5e: Don't treat small ceil values as unlimited in HTB offload
+    - net/mlx5: Bridge, Fix devlink deadlock on net namespace deletion
+    - net/mlx5: E-Switch, Fix uninitialized variable modact
+    - ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback
+    - i40e: Fix reset bw limit when DCB enabled with 1 TC
+    - i40e: Fix reset path while removing the driver
+    - net: amd-xgbe: ensure to reset the tx_timer_active flag
+    - net: amd-xgbe: Fix skb data length underflow
+    - fanotify: Fix stale file descriptor in copy_event_to_user()
+    - net: sched: fix use-after-free in tc_new_tfilter()
+    - rtnetlink: make sure to refresh master_dev/m_ops in __rtnl_newlink()
+    - cpuset: Fix the bug that subpart_cpus updated wrongly in update_cpumask()
+    - e1000e: Handshake with CSME starts from ADL platforms
+    - af_packet: fix data-race in packet_setsockopt / packet_setsockopt
+    - tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data()
+    - ovl: fix NULL pointer dereference in copy up warning
+    - Linux 5.15.20
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] use default zstd compression
+    - [Packaging] do not use compression for image packages
+    - [Packaging] use xz compression for ddebs
+    - [Config] upgrade debug symbols from DWARF4 to DWARF5
+    - SAUCE: Makefile: Remove inclusion of lbm header files
+    - SAUCE: Makefile: Fix compiler warnings
+    - SAUCE: AUFS
+    - SAUCE: aufs: switch to 64-bit ino_t for s390x
+    - [Config] set AUFS as disabled
+    - SAUCE: mt76: mt7921e: fix possible probe failure after reboot
+    - Remove ubuntu/hio driver
+    - SAUCE: ima_policy: fix test for empty rule set
+    - SAUCE: sfc: The size of the RX recycle ring should be more flexible
+    - [Config] MITIGATE_SPECTRE_BRANCH_HISTORY=y && HARDEN_BRANCH_HISTORY=y
+
+  * Miscellaneous upstream changes
+    - kbuild: Unify options for BTF generation for vmlinux and modules
+    - MAINTAINERS: Add scripts/pahole-flags.sh to BPF section
+    - kbuild: Add CONFIG_PAHOLE_VERSION
+    - scripts/pahole-flags.sh: Use pahole-version.sh
+    - lib/Kconfig.debug: Use CONFIG_PAHOLE_VERSION
+    - lib/Kconfig.debug: Allow BTF + DWARF5 with pahole 1.21+
+    - x86/sched: Decrease further the priorities of SMT siblings
+    - sched/topology: Introduce sched_group::flags
+    - sched/fair: Optimize checking for group_asym_packing
+    - sched/fair: Provide update_sg_lb_stats() with sched domain statistics
+    - sched/fair: Carve out logic to mark a group for asymmetric packing
+    - sched/fair: Consider SMT in ASYM_PACKING load balance
+    - Revert "UBUNTU: [Config] x86-64: SYSFB_SIMPLEFB=y"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Fri, 11 Mar 2022 11:24:13 +0100
+
+linux (5.15.0-22.22) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-22.22 -proposed tracker (LP: #1960290)
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 08 Feb 2022 10:48:49 +0100
+
+linux (5.15.0-21.21) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-21.21 -proposed tracker (LP: #1960211)
+
+  * Miscellaneous Ubuntu changes
+    - [packaging] unhook lowlatency flavours from the build
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 07 Feb 2022 11:30:18 +0100
+
+linux (5.15.0-20.20) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-20.20 -proposed tracker (LP: #1959881)
+
+  * Jammy update: v5.15.19 upstream stable release (LP: #1959879)
+    - can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if
+      length is 0
+    - net: sfp: ignore disabled SFP node
+    - net: stmmac: configure PTP clock source prior to PTP initialization
+    - net: stmmac: skip only stmmac_ptp_register when resume from suspend
+    - ARM: 9179/1: uaccess: avoid alignment faults in
+      copy_[from|to]_kernel_nofault
+    - ARM: 9180/1: Thumb2: align ALT_UP() sections in modules sufficiently
+    - KVM: arm64: Use shadow SPSR_EL1 when injecting exceptions on !VHE
+    - s390/hypfs: include z/VM guests with access control group set
+    - s390/nmi: handle guarded storage validity failures for KVM guests
+    - s390/nmi: handle vector validity failures for KVM guests
+    - bpf: Guard against accessing NULL pt_regs in bpf_get_task_stack()
+    - powerpc32/bpf: Fix codegen for bpf-to-bpf calls
+    - powerpc/bpf: Update ldimm64 instructions during extra pass
+    - scsi: zfcp: Fix failed recovery on gone remote port with non-NPIV FCP
+      devices
+    - udf: Restore i_lenAlloc when inode expansion fails
+    - udf: Fix NULL ptr deref when converting from inline format
+    - efi: runtime: avoid EFIv2 runtime services on Apple x86 machines
+    - PM: wakeup: simplify the output logic of pm_show_wakelocks()
+    - tracing/histogram: Fix a potential memory leak for kstrdup()
+    - tracing: Don't inc err_log entry count if entry allocation fails
+    - ceph: properly put ceph_string reference after async create attempt
+    - ceph: set pool_ns in new inode layout for async creates
+    - fsnotify: fix fsnotify hooks in pseudo filesystems
+    - Revert "KVM: SVM: avoid infinite loop on NPF from bad address"
+    - psi: Fix uaf issue when psi trigger is destroyed while being polled
+    - powerpc/audit: Fix syscall_get_arch()
+    - perf/x86/intel/uncore: Fix CAS_COUNT_WRITE issue for ICX
+    - perf/x86/intel: Add a quirk for the calculation of the number of counters on
+      Alder Lake
+    - drm/etnaviv: relax submit size limits
+    - drm/atomic: Add the crtc to affected crtc only if uapi.enable = true
+    - drm/amd/display: Fix FP start/end for dcn30_internal_validate_bw.
+    - KVM: LAPIC: Also cancel preemption timer during SET_LAPIC
+    - KVM: SVM: Never reject emulation due to SMAP errata for !SEV guests
+    - KVM: SVM: Don't intercept #GP for SEV guests
+    - KVM: x86: nSVM: skip eax alignment check for non-SVM instructions
+    - KVM: x86: Forcibly leave nested virt when SMM state is toggled
+    - KVM: x86: Keep MSR_IA32_XSS unchanged for INIT
+    - KVM: x86: Update vCPU's runtime CPUID on write to MSR_IA32_XSS
+    - KVM: x86: Sync the states size with the XCR0/IA32_XSS at, any time
+    - KVM: PPC: Book3S HV Nested: Fix nested HFSCR being clobbered with multiple
+      vCPUs
+    - dm: revert partial fix for redundant bio-based IO accounting
+    - block: add bio_start_io_acct_time() to control start_time
+    - dm: properly fix redundant bio-based IO accounting
+    - serial: pl011: Fix incorrect rs485 RTS polarity on set_mctrl
+    - serial: 8250: of: Fix mapped region size when using reg-offset property
+    - serial: stm32: fix software flow control transfer
+    - tty: n_gsm: fix SW flow control encoding/handling
+    - tty: Partially revert the removal of the Cyclades public API
+    - tty: Add support for Brainboxes UC cards.
+    - kbuild: remove include/linux/cyclades.h from header file check
+    - usb-storage: Add unusual-devs entry for VL817 USB-SATA bridge
+    - usb: xhci-plat: fix crash when suspend if remote wake enable
+    - usb: common: ulpi: Fix crash in ulpi_match()
+    - usb: gadget: f_sourcesink: Fix isoc transfer for USB_SPEED_SUPER_PLUS
+    - usb: cdnsp: Fix segmentation fault in cdns_lost_power function
+    - usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode
+    - usb: dwc3: xilinx: Fix error handling when getting USB3 PHY
+    - USB: core: Fix hang in usb_kill_urb by adding memory barriers
+    - usb: typec: tcpci: don't touch CC line if it's Vconn source
+    - usb: typec: tcpm: Do not disconnect while receiving VBUS off
+    - usb: typec: tcpm: Do not disconnect when receiving VSAFE0V
+    - ucsi_ccg: Check DEV_INT bit only when starting CCG4
+    - mm, kasan: use compare-exchange operation to set KASAN page tag
+    - jbd2: export jbd2_journal_[grab|put]_journal_head
+    - ocfs2: fix a deadlock when commit trans
+    - sched/membarrier: Fix membarrier-rseq fence command missing from query
+      bitmask
+    - PCI/sysfs: Find shadow ROM before static attribute initialization
+    - x86/MCE/AMD: Allow thresholding interface updates after init
+    - x86/cpu: Add Xeon Icelake-D to list of CPUs that support PPIN
+    - powerpc/32s: Allocate one 256k IBAT instead of two consecutives 128k IBATs
+    - powerpc/32s: Fix kasan_init_region() for KASAN
+    - powerpc/32: Fix boot failure with GCC latent entropy plugin
+    - i40e: Increase delay to 1 s after global EMP reset
+    - i40e: Fix issue when maximum queues is exceeded
+    - i40e: Fix queues reservation for XDP
+    - i40e: Fix for failed to init adminq while VF reset
+    - i40e: fix unsigned stat widths
+    - usb: roles: fix include/linux/usb/role.h compile issue
+    - rpmsg: char: Fix race between the release of rpmsg_ctrldev and cdev
+    - rpmsg: char: Fix race between the release of rpmsg_eptdev and cdev
+    - scsi: elx: efct: Don't use GFP_KERNEL under spin lock
+    - scsi: bnx2fc: Flush destroy_work queue before calling bnx2fc_interface_put()
+    - ipv6_tunnel: Rate limit warning messages
+    - ARM: 9170/1: fix panic when kasan and kprobe are enabled
+    - net: fix information leakage in /proc/net/ptype
+    - hwmon: (lm90) Mark alert as broken for MAX6646/6647/6649
+    - hwmon: (lm90) Mark alert as broken for MAX6680
+    - ping: fix the sk_bound_dev_if match in ping_lookup
+    - ipv4: avoid using shared IP generator for connected sockets
+    - hwmon: (lm90) Reduce maximum conversion rate for G781
+    - NFSv4: Handle case where the lookup of a directory fails
+    - NFSv4: nfs_atomic_open() can race when looking up a non-regular file
+    - net-procfs: show net devices bound packet types
+    - drm/msm: Fix wrong size calculation
+    - drm/msm/dsi: Fix missing put_device() call in dsi_get_phy
+    - drm/msm/dsi: invalid parameter check in msm_dsi_phy_enable
+    - ipv6: annotate accesses to fn->fn_sernum
+    - NFS: Ensure the server has an up to date ctime before hardlinking
+    - NFS: Ensure the server has an up to date ctime before renaming
+    - KVM: arm64: pkvm: Use the mm_ops indirection for cache maintenance
+    - SUNRPC: Use BIT() macro in rpc_show_xprt_state()
+    - SUNRPC: Don't dereference xprt->snd_task if it's a cookie
+    - powerpc64/bpf: Limit 'ldbrx' to processors compliant with ISA v2.06
+    - netfilter: conntrack: don't increment invalid counter on NF_REPEAT
+    - powerpc/64s: Mask SRR0 before checking against the masked NIP
+    - perf: Fix perf_event_read_local() time
+    - sched/pelt: Relax the sync of util_sum with util_avg
+    - net: phy: broadcom: hook up soft_reset for BCM54616S
+    - net: stmmac: dwmac-visconti: Fix bit definitions for ETHER_CLK_SEL
+    - net: stmmac: dwmac-visconti: Fix clock configuration for RMII mode
+    - phylib: fix potential use-after-free
+    - octeontx2-af: Do not fixup all VF action entries
+    - octeontx2-af: Fix LBK backpressure id count
+    - octeontx2-af: Retry until RVU block reset complete
+    - octeontx2-pf: cn10k: Ensure valid pointers are freed to aura
+    - octeontx2-af: verify CQ context updates
+    - octeontx2-af: Increase link credit restore polling timeout
+    - octeontx2-af: cn10k: Do not enable RPM loopback for LPC interfaces
+    - octeontx2-pf: Forward error codes to VF
+    - rxrpc: Adjust retransmission backoff
+    - efi/libstub: arm64: Fix image check alignment at entry
+    - io_uring: fix bug in slow unregistering of nodes
+    - Drivers: hv: balloon: account for vmbus packet header in max_pkt_size
+    - hwmon: (lm90) Re-enable interrupts after alert clears
+    - hwmon: (lm90) Mark alert as broken for MAX6654
+    - hwmon: (lm90) Fix sysfs and udev notifications
+    - hwmon: (adt7470) Prevent divide by zero in adt7470_fan_write()
+    - powerpc/perf: Fix power_pmu_disable to call clear_pmi_irq_pending only if
+      PMI is pending
+    - ipv4: fix ip option filtering for locally generated fragments
+    - ibmvnic: Allow extra failures before disabling
+    - ibmvnic: init ->running_cap_crqs early
+    - ibmvnic: don't spin in tasklet
+    - net/smc: Transitional solution for clcsock race issue
+    - video: hyperv_fb: Fix validation of screen resolution
+    - can: tcan4x5x: regmap: fix max register value
+    - drm/msm/hdmi: Fix missing put_device() call in msm_hdmi_get_phy
+    - drm/msm/dpu: invalid parameter check in dpu_setup_dspp_pcc
+    - drm/msm/a6xx: Add missing suspend_count increment
+    - yam: fix a memory leak in yam_siocdevprivate()
+    - net: cpsw: Properly initialise struct page_pool_params
+    - net: hns3: handle empty unknown interrupt for VF
+    - sch_htb: Fail on unsupported parameters when offload is requested
+    - Revert "drm/ast: Support 1600x900 with 108MHz PCLK"
+    - KVM: selftests: Don't skip L2's VMCALL in SMM test for SVM guest
+    - ceph: put the requests/sessions when it fails to alloc memory
+    - gve: Fix GFP flags when allocing pages
+    - Revert "ipv6: Honor all IPv6 PIO Valid Lifetime values"
+    - net: bridge: vlan: fix single net device option dumping
+    - ipv4: raw: lock the socket in raw_bind()
+    - ipv4: tcp: send zero IPID in SYNACK messages
+    - ipv4: remove sparse error in ip_neigh_gw4()
+    - net: bridge: vlan: fix memory leak in __allowed_ingress
+    - Bluetooth: refactor malicious adv data check
+    - irqchip/realtek-rtl: Map control data to virq
+    - irqchip/realtek-rtl: Fix off-by-one in routing
+    - dt-bindings: can: tcan4x5x: fix mram-cfg RX FIFO config
+    - perf/core: Fix cgroup event list management
+    - psi: fix "no previous prototype" warnings when CONFIG_CGROUPS=n
+    - psi: fix "defined but not used" warnings when CONFIG_PROC_FS=n
+    - usb: dwc3: xilinx: fix uninitialized return value
+    - usr/include/Makefile: add linux/nfc.h to the compile-test coverage
+    - fsnotify: invalidate dcache before IN_DELETE event
+    - block: Fix wrong offset in bio_truncate()
+    - mtd: rawnand: mpc5121: Remove unused variable in ads5121_select_chip()
+    - Linux 5.15.19
+
+  * Jammy update: v5.15.18 upstream stable release (LP: #1959878)
+    - drm/i915: Flush TLBs before releasing backing store
+    - drm/amd/display: reset dcn31 SMU mailbox on failures
+    - io_uring: fix not released cached task refs
+    - bnx2x: Utilize firmware 7.13.21.0
+    - bnx2x: Invalidate fastpath HSI version for VFs
+    - memcg: flush stats only if updated
+    - memcg: unify memcg stat flushing
+    - memcg: better bounds on the memcg stats updates
+    - rcu: Tighten rcu_advance_cbs_nowake() checks
+    - select: Fix indefinitely sleeping task in poll_schedule_timeout()
+    - drm/amdgpu: Use correct VIEWPORT_DIMENSION for DCN2
+    - arm64/bpf: Remove 128MB limit for BPF JIT programs
+    - Linux 5.15.18
+
+  * CVE-2022-22942
+    - SAUCE: drm/vmwgfx: Fix stale file descriptors on failed usercopy
+
+  * CVE-2022-24122
+    - ucount: Make get_ucount a safe get_user replacement
+
+  * CVE-2022-23222
+    - bpf, selftests: Add verifier test for mem_or_null register with offset.
+
+  * Miscellaneous Ubuntu changes
+    - [Config] toolchain version update
+
+  * Miscellaneous upstream changes
+    - s390/module: fix loading modules with a lot of relocations
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 03 Feb 2022 12:09:37 +0100
+
+linux (5.15.0-19.19) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-19.19 -proposed tracker (LP: #1959418)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Jammy update: v5.15.17 upstream stable release (LP: #1959376)
+    - KVM: x86/mmu: Fix write-protection of PTs mapped by the TDP MMU
+    - KVM: VMX: switch blocked_vcpu_on_cpu_lock to raw spinlock
+    - HID: Ignore battery for Elan touchscreen on HP Envy X360 15t-dr100
+    - HID: uhid: Fix worker destroying device without any protection
+    - HID: wacom: Reset expected and received contact counts at the same time
+    - HID: wacom: Ignore the confidence flag when a touch is removed
+    - HID: wacom: Avoid using stale array indicies to read contact count
+    - ALSA: core: Fix SSID quirk lookup for subvendor=0
+    - f2fs: fix to do sanity check on inode type during garbage collection
+    - f2fs: fix to do sanity check in is_alive()
+    - f2fs: avoid EINVAL by SBI_NEED_FSCK when pinning a file
+    - nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed
+      bind()
+    - mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timings
+    - mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6
+    - mtd: Fixed breaking list in __mtd_del_partition.
+    - mtd: rawnand: davinci: Don't calculate ECC when reading page
+    - mtd: rawnand: davinci: Avoid duplicated page read
+    - mtd: rawnand: davinci: Rewrite function description
+    - mtd: rawnand: Export nand_read_page_hwecc_oob_first()
+    - mtd: rawnand: ingenic: JZ4740 needs 'oob_first' read page function
+    - riscv: Get rid of MAXPHYSMEM configs
+    - RISC-V: Use common riscv_cpuid_to_hartid_mask() for both SMP=y and SMP=n
+    - riscv: try to allocate crashkern region from 32bit addressible memory
+    - riscv: Don't use va_pa_offset on kdump
+    - riscv: use hart id instead of cpu id on machine_kexec
+    - riscv: mm: fix wrong phys_ram_base value for RV64
+    - x86/gpu: Reserve stolen memory for first integrated Intel GPU
+    - tools/nolibc: x86-64: Fix startup code bug
+    - crypto: x86/aesni - don't require alignment of data
+    - tools/nolibc: i386: fix initial stack alignment
+    - tools/nolibc: fix incorrect truncation of exit code
+    - rtc: cmos: take rtc_lock while reading from CMOS
+    - net: phy: marvell: add Marvell specific PHY loopback
+    - ksmbd: uninitialized variable in create_socket()
+    - ksmbd: fix guest connection failure with nautilus
+    - ksmbd: add support for smb2 max credit parameter
+    - ksmbd: move credit charge deduction under processing request
+    - ksmbd: limits exceeding the maximum allowable outstanding requests
+    - ksmbd: add reserved room in ipc request/response
+    - media: cec: fix a deadlock situation
+    - media: ov8865: Disable only enabled regulators on error path
+    - media: v4l2-ioctl.c: readbuffers depends on V4L2_CAP_READWRITE
+    - media: flexcop-usb: fix control-message timeouts
+    - media: mceusb: fix control-message timeouts
+    - media: em28xx: fix control-message timeouts
+    - media: cpia2: fix control-message timeouts
+    - media: s2255: fix control-message timeouts
+    - media: dib0700: fix undefined behavior in tuner shutdown
+    - media: redrat3: fix control-message timeouts
+    - media: pvrusb2: fix control-message timeouts
+    - media: stk1160: fix control-message timeouts
+    - media: cec-pin: fix interrupt en/disable handling
+    - can: softing_cs: softingcs_probe(): fix memleak on registration failure
+    - mei: hbm: fix client dma reply status
+    - iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
+    - iio: trigger: Fix a scheduling whilst atomic issue seen on tsc2046
+    - lkdtm: Fix content of section containing lkdtm_rodata_do_nothing()
+    - bus: mhi: pci_generic: Graceful shutdown on freeze
+    - bus: mhi: core: Fix reading wake_capable channel configuration
+    - bus: mhi: core: Fix race while handling SYS_ERR at power up
+    - cxl/pmem: Fix reference counting for delayed work
+    - arm64: errata: Fix exec handling in erratum 1418040 workaround
+    - ARM: dts: at91: update alternate function of signal PD20
+    - iommu/io-pgtable-arm-v7s: Add error handle for page table allocation failure
+    - gpu: host1x: Add back arm_iommu_detach_device()
+    - drm/tegra: Add back arm_iommu_detach_device()
+    - virtio/virtio_mem: handle a possible NULL as a memcpy parameter
+    - dma_fence_array: Fix PENDING_ERROR leak in dma_fence_array_signaled()
+    - PCI: Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
+    - mm_zone: add function to check if managed dma zone exists
+    - dma/pool: create dma atomic pool only if dma zone has managed pages
+    - mm/page_alloc.c: do not warn allocation failure on zone DMA if no managed
+      pages
+    - shmem: fix a race between shmem_unused_huge_shrink and shmem_evict_inode
+    - drm/ttm: Put BO in its memory manager's lru list
+    - Bluetooth: L2CAP: Fix not initializing sk_peer_pid
+    - drm/bridge: display-connector: fix an uninitialized pointer in probe()
+    - drm: fix null-ptr-deref in drm_dev_init_release()
+    - drm/panel: kingdisplay-kd097d04: Delete panel on attach() failure
+    - drm/panel: innolux-p079zca: Delete panel on attach() failure
+    - drm/rockchip: dsi: Fix unbalanced clock on probe error
+    - drm/rockchip: dsi: Hold pm-runtime across bind/unbind
+    - drm/rockchip: dsi: Disable PLL clock on bind error
+    - drm/rockchip: dsi: Reconfigure hardware on resume()
+    - Bluetooth: virtio_bt: fix memory leak in virtbt_rx_handle()
+    - Bluetooth: cmtp: fix possible panic when cmtp_init_sockets() fails
+    - clk: bcm-2835: Pick the closest clock rate
+    - clk: bcm-2835: Remove rounding up the dividers
+    - drm/vc4: hdmi: Set a default HSM rate
+    - drm/vc4: hdmi: Move the HSM clock enable to runtime_pm
+    - drm/vc4: hdmi: Make sure the controller is powered in detect
+    - drm/vc4: hdmi: Make sure the controller is powered up during bind
+    - drm/vc4: hdmi: Rework the pre_crtc_configure error handling
+    - drm/vc4: crtc: Make sure the HDMI controller is powered when disabling
+    - wcn36xx: ensure pairing of init_scan/finish_scan and start_scan/end_scan
+    - wcn36xx: Indicate beacon not connection loss on MISSED_BEACON_IND
+    - drm/vc4: hdmi: Enable the scrambler on reconnection
+    - libbpf: Free up resources used by inner map definition
+    - wcn36xx: Fix DMA channel enable/disable cycle
+    - wcn36xx: Release DMA channel descriptor allocations
+    - wcn36xx: Put DXE block into reset before freeing memory
+    - wcn36xx: populate band before determining rate on RX
+    - wcn36xx: fix RX BD rate mapping for 5GHz legacy rates
+    - ath11k: Send PPDU_STATS_CFG with proper pdev mask to firmware
+    - bpftool: Fix memory leak in prog_dump()
+    - mtd: hyperbus: rpc-if: Check return value of rpcif_sw_init()
+    - media: videobuf2: Fix the size printk format
+    - media: atomisp: add missing media_device_cleanup() in
+      atomisp_unregister_entities()
+    - media: atomisp: fix punit_ddr_dvfs_enable() argument for mrfld_power up case
+    - media: atomisp: fix inverted logic in buffers_needed()
+    - media: atomisp: do not use err var when checking port validity for ISP2400
+    - media: atomisp: fix inverted error check for
+      ia_css_mipi_is_source_port_valid()
+    - media: atomisp: fix ifdefs in sh_css.c
+    - media: atomisp: add NULL check for asd obtained from atomisp_video_pipe
+    - media: atomisp: fix enum formats logic
+    - media: atomisp: fix uninitialized bug in gmin_get_pmic_id_and_addr()
+    - media: aspeed: fix mode-detect always time out at 2nd run
+    - media: em28xx: fix memory leak in em28xx_init_dev
+    - media: aspeed: Update signal status immediately to ensure sane hw state
+    - arm64: dts: amlogic: meson-g12: Fix GPU operating point table node name
+    - arm64: dts: amlogic: Fix SPI NOR flash node name for ODROID N2/N2+
+    - arm64: dts: meson-gxbb-wetek: fix HDMI in early boot
+    - arm64: dts: meson-gxbb-wetek: fix missing GPIO binding
+    - fs: dlm: don't call kernel_getpeername() in error_report()
+    - memory: renesas-rpc-if: Return error in case devm_ioremap_resource() fails
+    - Bluetooth: stop proccessing malicious adv data
+    - ath11k: Fix ETSI regd with weather radar overlap
+    - ath11k: clear the keys properly via DISABLE_KEY
+    - ath11k: reset RSN/WPA present state for open BSS
+    - spi: hisi-kunpeng: Fix the debugfs directory name incorrect
+    - tee: fix put order in teedev_close_context()
+    - fs: dlm: fix build with CONFIG_IPV6 disabled
+    - drm/dp: Don't read back backlight mode in drm_edp_backlight_enable()
+    - drm/vboxvideo: fix a NULL vs IS_ERR() check
+    - arm64: dts: renesas: cat875: Add rx/tx delays
+    - media: dmxdev: fix UAF when dvb_register_device() fails
+    - crypto: atmel-aes - Reestablish the correct tfm context at dequeue
+    - crypto: qce - fix uaf on qce_aead_register_one
+    - crypto: qce - fix uaf on qce_ahash_register_one
+    - crypto: qce - fix uaf on qce_skcipher_register_one
+    - arm64: dts: qcom: sc7280: Fix incorrect clock name
+    - mtd: hyperbus: rpc-if: fix bug in rpcif_hb_remove
+    - cpufreq: qcom-cpufreq-hw: Update offline CPUs per-cpu thermal pressure
+    - cpufreq: qcom-hw: Fix probable nested interrupt handling
+    - ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding on stm32f429
+      disco
+    - libbpf: Fix potential misaligned memory access in btf_ext__new()
+    - libbpf: Fix glob_syms memory leak in bpf_linker
+    - libbpf: Fix using invalidated memory in bpf_linker
+    - crypto: qat - remove unnecessary collision prevention step in PFVF
+    - crypto: qat - make pfvf send message direction agnostic
+    - crypto: qat - fix undetected PFVF timeout in ACK loop
+    - ath11k: Use host CE parameters for CE interrupts configuration
+    - arm64: dts: ti: k3-j721e: correct cache-sets info
+    - tty: serial: atmel: Check return code of dmaengine_submit()
+    - tty: serial: atmel: Call dma_async_issue_pending()
+    - mfd: atmel-flexcom: Remove #ifdef CONFIG_PM_SLEEP
+    - mfd: atmel-flexcom: Use .resume_noirq
+    - bfq: Do not let waker requests skip proper accounting
+    - libbpf: Silence uninitialized warning/error in btf_dump_dump_type_data
+    - media: i2c: imx274: fix s_frame_interval runtime resume not requested
+    - media: i2c: Re-order runtime pm initialisation
+    - media: i2c: ov8865: Fix lockdep error
+    - media: rcar-csi2: Correct the selection of hsfreqrange
+    - media: imx-pxp: Initialize the spinlock prior to using it
+    - media: si470x-i2c: fix possible memory leak in si470x_i2c_probe()
+    - media: mtk-vcodec: call v4l2_m2m_ctx_release first when file is released
+    - media: hantro: Hook up RK3399 JPEG encoder output
+    - media: coda: fix CODA960 JPEG encoder buffer overflow
+    - media: venus: correct low power frequency calculation for encoder
+    - media: venus: core: Fix a potential NULL pointer dereference in an error
+      handling path
+    - media: venus: core: Fix a resource leak in the error handling path of
+      'venus_probe()'
+    - net: stmmac: Add platform level debug register dump feature
+    - thermal/drivers/imx: Implement runtime PM support
+    - igc: AF_XDP zero-copy metadata adjust breaks SKBs on XDP_PASS
+    - netfilter: bridge: add support for pppoe filtering
+    - powerpc: Avoid discarding flags in system_call_exception()
+    - arm64: dts: qcom: msm8916: fix MMC controller aliases
+    - drm/vmwgfx: Remove the deprecated lower mem limit
+    - drm/vmwgfx: Fail to initialize on broken configs
+    - cgroup: Trace event cgroup id fields should be u64
+    - ACPI: EC: Rework flushing of EC work while suspended to idle
+    - thermal/drivers/imx8mm: Enable ADC when enabling monitor
+    - drm/amdgpu: Fix a NULL pointer dereference in
+      amdgpu_connector_lcd_native_mode()
+    - drm/radeon/radeon_kms: Fix a NULL pointer dereference in
+      radeon_driver_open_kms()
+    - libbpf: Clean gen_loader's attach kind.
+    - crypto: caam - save caam memory to support crypto engine retry mechanism.
+    - arm64: dts: ti: k3-am642: Fix the L2 cache sets
+    - arm64: dts: ti: k3-j7200: Fix the L2 cache sets
+    - arm64: dts: ti: k3-j721e: Fix the L2 cache sets
+    - arm64: dts: ti: k3-j7200: Correct the d-cache-sets info
+    - tty: serial: uartlite: allow 64 bit address
+    - serial: amba-pl011: do not request memory region twice
+    - mtd: core: provide unique name for nvmem device
+    - floppy: Fix hang in watchdog when disk is ejected
+    - staging: rtl8192e: return error code from rtllib_softmac_init()
+    - staging: rtl8192e: rtllib_module: fix error handle case in alloc_rtllib()
+    - Bluetooth: btmtksdio: fix resume failure
+    - bpf: Fix the test_task_vma selftest to support output shorter than 1 kB
+    - sched/fair: Fix detection of per-CPU kthreads waking a task
+    - sched/fair: Fix per-CPU kthread and wakee stacking for asym CPU capacity
+    - bpf: Adjust BTF log size limit.
+    - bpf: Disallow BPF_LOG_KERNEL log level for bpf(BPF_BTF_LOAD)
+    - bpf: Remove config check to enable bpf support for branch records
+    - arm64: clear_page() shouldn't use DC ZVA when DCZID_EL0.DZP == 1
+    - arm64: mte: DC {GVA,GZVA} shouldn't be used when DCZID_EL0.DZP == 1
+    - samples/bpf: Install libbpf headers when building
+    - samples/bpf: Clean up samples/bpf build failes
+    - samples: bpf: Fix xdp_sample_user.o linking with Clang
+    - samples: bpf: Fix 'unknown warning group' build warning on Clang
+    - media: dib8000: Fix a memleak in dib8000_init()
+    - media: saa7146: mxb: Fix a NULL pointer dereference in mxb_attach()
+    - media: si2157: Fix "warm" tuner state detection
+    - wireless: iwlwifi: Fix a double free in iwl_txq_dyn_alloc_dma
+    - sched/rt: Try to restart rt period timer when rt runtime exceeded
+    - ath10k: Fix the MTU size on QCA9377 SDIO
+    - Bluetooth: refactor set_exp_feature with a feature table
+    - Bluetooth: MGMT: Use hci_dev_test_and_{set,clear}_flag
+    - drm/amd/display: Fix bug in debugfs crc_win_update entry
+    - drm/msm/gpu: Don't allow zero fence_id
+    - drm/msm/dp: displayPort driver need algorithm rational
+    - rcu/exp: Mark current CPU as exp-QS in IPI loop second pass
+    - wcn36xx: Fix max channels retrieval
+    - drm/msm/dsi: fix initialization in the bonded DSI case
+    - mwifiex: Fix possible ABBA deadlock
+    - xfrm: fix a small bug in xfrm_sa_len()
+    - x86/uaccess: Move variable into switch case statement
+    - selftests: clone3: clone3: add case CLONE3_ARGS_NO_TEST
+    - selftests: harness: avoid false negatives if test has no ASSERTs
+    - crypto: stm32/cryp - fix CTR counter carry
+    - crypto: stm32/cryp - fix xts and race condition in crypto_engine requests
+    - crypto: stm32/cryp - check early input data
+    - crypto: stm32/cryp - fix double pm exit
+    - crypto: stm32/cryp - fix lrw chaining mode
+    - crypto: stm32/cryp - fix bugs and crash in tests
+    - crypto: stm32 - Revert broken pm_runtime_resume_and_get changes
+    - crypto: hisilicon/qm - fix incorrect return value of hisi_qm_resume()
+    - ath11k: Fix deleting uninitialized kernel timer during fragment cache flush
+    - spi: Fix incorrect cs_setup delay handling
+    - ARM: dts: gemini: NAS4220-B: fis-index-block with 128 KiB sectors
+    - perf/arm-cmn: Fix CPU hotplug unregistration
+    - media: dw2102: Fix use after free
+    - media: msi001: fix possible null-ptr-deref in msi001_probe()
+    - media: coda/imx-vdoa: Handle dma_set_coherent_mask error codes
+    - ath11k: Fix a NULL pointer dereference in ath11k_mac_op_hw_scan()
+    - net: dsa: hellcreek: Fix insertion of static FDB entries
+    - net: dsa: hellcreek: Add STP forwarding rule
+    - net: dsa: hellcreek: Allow PTP P2P measurements on blocked ports
+    - net: dsa: hellcreek: Add missing PTP via UDP rules
+    - arm64: dts: qcom: c630: Fix soundcard setup
+    - arm64: dts: qcom: ipq6018: Fix gpio-ranges property
+    - drm/msm/dpu: fix safe status debugfs file
+    - drm/bridge: ti-sn65dsi86: Set max register for regmap
+    - gpu: host1x: select CONFIG_DMA_SHARED_BUFFER
+    - drm/tegra: gr2d: Explicitly control module reset
+    - drm/tegra: vic: Fix DMA API misuse
+    - media: hantro: Fix probe func error path
+    - xfrm: interface with if_id 0 should return error
+    - xfrm: state and policy should fail if XFRMA_IF_ID 0
+    - ARM: 9159/1: decompressor: Avoid UNPREDICTABLE NOP encoding
+    - usb: ftdi-elan: fix memory leak on device disconnect
+    - arm64: dts: marvell: cn9130: add GPIO and SPI aliases
+    - arm64: dts: marvell: cn9130: enable CP0 GPIO controllers
+    - ARM: dts: armada-38x: Add generic compatible to UART nodes
+    - mt76: mt7921: drop offload_flags overwritten
+    - wilc1000: fix double free error in probe()
+    - rtw88: add quirk to disable pci caps on HP 250 G7 Notebook PC
+    - iwlwifi: mvm: fix 32-bit build in FTM
+    - iwlwifi: mvm: test roc running status bits before removing the sta
+    - iwlwifi: mvm: perform 6GHz passive scan after suspend
+    - iwlwifi: mvm: set protected flag only for NDP ranging
+    - mmc: meson-mx-sdhc: add IRQ check
+    - mmc: meson-mx-sdio: add IRQ check
+    - block: fix error unwinding in device_add_disk
+    - selinux: fix potential memleak in selinux_add_opt()
+    - um: fix ndelay/udelay defines
+    - um: rename set_signals() to um_set_signals()
+    - um: virt-pci: Fix 32-bit compile
+    - lib/logic_iomem: Fix 32-bit build
+    - lib/logic_iomem: Fix operation on 32-bit
+    - um: virtio_uml: Fix time-travel external time propagation
+    - Bluetooth: L2CAP: Fix using wrong mode
+    - bpftool: Enable line buffering for stdout
+    - backlight: qcom-wled: Validate enabled string indices in DT
+    - backlight: qcom-wled: Pass number of elements to read to read_u32_array
+    - backlight: qcom-wled: Fix off-by-one maximum with default num_strings
+    - backlight: qcom-wled: Override default length with qcom,enabled-strings
+    - backlight: qcom-wled: Use cpu_to_le16 macro to perform conversion
+    - backlight: qcom-wled: Respect enabled-strings in set_brightness
+    - software node: fix wrong node passed to find nargs_prop
+    - Bluetooth: hci_qca: Stop IBS timer during BT OFF
+    - x86/boot/compressed: Move CLANG_FLAGS to beginning of KBUILD_CFLAGS
+    - crypto: octeontx2 - prevent underflow in get_cores_bmap()
+    - regulator: qcom-labibb: OCP interrupts are not a failure while disabled
+    - hwmon: (mr75203) fix wrong power-up delay value
+    - x86/mce/inject: Avoid out-of-bounds write when setting flags
+    - io_uring: remove double poll on poll update
+    - serial: 8250_bcm7271: Propagate error codes from brcmuart_probe()
+    - ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
+    - pcmcia: rsrc_nonstatic: Fix a NULL pointer dereference in
+      __nonstatic_find_io_region()
+    - pcmcia: rsrc_nonstatic: Fix a NULL pointer dereference in
+      nonstatic_find_mem_region()
+    - power: reset: mt6397: Check for null res pointer
+    - net/xfrm: IPsec tunnel mode fix inner_ipproto setting in sec_path
+    - net: ethernet: mtk_eth_soc: fix return values and refactor MDIO ops
+    - net: dsa: fix incorrect function pointer check for MRP ring roles
+    - netfilter: ipt_CLUSTERIP: fix refcount leak in clusterip_tg_check()
+    - bpf, sockmap: Fix return codes from tcp_bpf_recvmsg_parser()
+    - bpf, sockmap: Fix double bpf_prog_put on error case in map_link
+    - bpf: Don't promote bogus looking registers after null check.
+    - bpf: Fix verifier support for validation of async callbacks
+    - bpf: Fix SO_RCVBUF/SO_SNDBUF handling in _bpf_setsockopt().
+    - netfilter: nft_payload: do not update layer 4 checksum when mangling
+      fragments
+    - netfilter: nft_set_pipapo: allocate pcpu scratch maps on clone
+    - net: fix SOF_TIMESTAMPING_BIND_PHC to work with multiple sockets
+    - ppp: ensure minimum packet size in ppp_write()
+    - rocker: fix a sleeping in atomic bug
+    - staging: greybus: audio: Check null pointer
+    - fsl/fman: Check for null pointer after calling devm_ioremap
+    - Bluetooth: hci_bcm: Check for error irq
+    - Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe
+    - net/smc: Reset conn->lgr when link group registration fails
+    - usb: dwc3: qcom: Fix NULL vs IS_ERR checking in dwc3_qcom_probe
+    - usb: dwc2: do not gate off the hardware if it does not support clock gating
+    - usb: dwc2: gadget: initialize max_speed from params
+    - usb: gadget: u_audio: Subdevice 0 for capture ctls
+    - HID: hid-uclogic-params: Invalid parameter check in uclogic_params_init
+    - HID: hid-uclogic-params: Invalid parameter check in
+      uclogic_params_get_str_desc
+    - HID: hid-uclogic-params: Invalid parameter check in
+      uclogic_params_huion_init
+    - HID: hid-uclogic-params: Invalid parameter check in
+      uclogic_params_frame_init_v1_buttonpad
+    - debugfs: lockdown: Allow reading debugfs files that are not world readable
+    - drivers/firmware: Add missing platform_device_put() in sysfb_create_simplefb
+    - serial: liteuart: fix MODULE_ALIAS
+    - serial: stm32: move tx dma terminate DMA to shutdown
+    - x86, sched: Fix undefined reference to init_freq_invariance_cppc() build
+      error
+    - net/mlx5e: Fix page DMA map/unmap attributes
+    - net/mlx5e: Fix wrong usage of fib_info_nh when routes with nexthop objects
+      are used
+    - net/mlx5e: Don't block routes with nexthop objects in SW
+    - Revert "net/mlx5e: Block offload of outer header csum for UDP tunnels"
+    - Revert "net/mlx5e: Block offload of outer header csum for GRE tunnel"
+    - net/mlx5e: Fix matching on modified inner ip_ecn bits
+    - net/mlx5: Fix access to sf_dev_table on allocation failure
+    - net/mlx5e: Sync VXLAN udp ports during uplink representor profile change
+    - net/mlx5: Set command entry semaphore up once got index free
+    - lib/mpi: Add the return value check of kcalloc()
+    - Bluetooth: L2CAP: uninitialized variables in l2cap_sock_setsockopt()
+    - mptcp: fix per socket endpoint accounting
+    - mptcp: fix opt size when sending DSS + MP_FAIL
+    - mptcp: fix a DSS option writing error
+    - spi: spi-meson-spifc: Add missing pm_runtime_disable() in meson_spifc_probe
+    - octeontx2-af: Increment ptp refcount before use
+    - ax25: uninitialized variable in ax25_setsockopt()
+    - netrom: fix api breakage in nr_setsockopt()
+    - regmap: Call regmap_debugfs_exit() prior to _init()
+    - net: mscc: ocelot: fix incorrect balancing with down LAG ports
+    - can: mcp251xfd: add missing newline to printed strings
+    - tpm: add request_locality before write TPM_INT_ENABLE
+    - tpm_tis: Fix an error handling path in 'tpm_tis_core_init()'
+    - can: softing: softing_startstop(): fix set but not used variable warning
+    - can: xilinx_can: xcan_probe(): check for error irq
+    - can: rcar_canfd: rcar_canfd_channel_probe(): make sure we free CAN network
+      device
+    - pcmcia: fix setting of kthread task states
+    - net/sched: flow_dissector: Fix matching on zone id for invalid conns
+    - net: openvswitch: Fix matching zone id for invalid conns arriving from tc
+    - net: openvswitch: Fix ct_state nat flags for conns arriving from tc
+    - iwlwifi: mvm: Use div_s64 instead of do_div in iwl_mvm_ftm_rtt_smoothing()
+    - bnxt_en: Refactor coredump functions
+    - bnxt_en: move coredump functions into dedicated file
+    - bnxt_en: use firmware provided max timeout for messages
+    - net: mcs7830: handle usb read errors properly
+    - ext4: avoid trim error on fs with small groups
+    - ASoC: Intel: sof_sdw: fix jack detection on HP Spectre x360 convertible
+    - ALSA: jack: Add missing rwsem around snd_ctl_remove() calls
+    - ALSA: PCM: Add missing rwsem around snd_ctl_remove() calls
+    - ALSA: hda: Add missing rwsem around snd_ctl_remove() calls
+    - ALSA: hda: Fix potential deadlock at codec unbinding
+    - RDMA/bnxt_re: Scan the whole bitmap when checking if "disabling RCFW with
+      pending cmd-bit"
+    - RDMA/hns: Validate the pkey index
+    - scsi: pm80xx: Update WARN_ON check in pm8001_mpi_build_cmd()
+    - clk: renesas: rzg2l: Check return value of pm_genpd_init()
+    - clk: renesas: rzg2l: propagate return value of_genpd_add_provider_simple()
+    - clk: imx8mn: Fix imx8mn_clko1_sels
+    - powerpc/prom_init: Fix improper check of prom_getprop()
+    - ASoC: uniphier: drop selecting non-existing SND_SOC_UNIPHIER_AIO_DMA
+    - ASoC: codecs: wcd938x: add SND_SOC_WCD938_SDW to codec list instead
+    - RDMA/rtrs-clt: Fix the initial value of min_latency
+    - ALSA: hda: Make proper use of timecounter
+    - dt-bindings: thermal: Fix definition of cooling-maps contribution property
+    - powerpc/perf: Fix PMU callbacks to clear pending PMI before resetting an
+      overflown PMC
+    - powerpc/modules: Don't WARN on first module allocation attempt
+    - powerpc/32s: Fix shift-out-of-bounds in KASAN init
+    - clocksource: Avoid accidental unstable marking of clocksources
+    - ALSA: oss: fix compile error when OSS_DEBUG is enabled
+    - ALSA: usb-audio: Drop superfluous '0' in Presonus Studio 1810c's ID
+    - misc: at25: Make driver OF independent again
+    - char/mwave: Adjust io port register size
+    - binder: fix handling of error during copy
+    - binder: avoid potential data leakage when copying txn
+    - openrisc: Add clone3 ABI wrapper
+    - iommu: Extend mutex lock scope in iommu_probe_device()
+    - iommu/io-pgtable-arm: Fix table descriptor paddr formatting
+    - scsi: core: Fix scsi_device_max_queue_depth()
+    - scsi: ufs: Fix race conditions related to driver data
+    - RDMA/qedr: Fix reporting max_{send/recv}_wr attrs
+    - PCI/MSI: Fix pci_irq_vector()/pci_irq_get_affinity()
+    - powerpc/powermac: Add additional missing lockdep_register_key()
+    - iommu/arm-smmu-qcom: Fix TTBR0 read
+    - RDMA/core: Let ib_find_gid() continue search even after empty entry
+    - RDMA/cma: Let cma_resolve_ib_dev() continue search even after empty entry
+    - ASoC: rt5663: Handle device_property_read_u32_array error codes
+    - of: unittest: fix warning on PowerPC frame size warning
+    - of: unittest: 64 bit dma address test requires arch support
+    - clk: stm32: Fix ltdc's clock turn off by clk_disable_unused() after system
+      enter shell
+    - mips: add SYS_HAS_CPU_MIPS64_R5 config for MIPS Release 5 support
+    - mips: fix Kconfig reference to PHYS_ADDR_T_64BIT
+    - dmaengine: pxa/mmp: stop referencing config->slave_id
+    - iommu/amd: Restore GA log/tail pointer on host resume
+    - iommu/amd: X2apic mode: re-enable after resume
+    - iommu/amd: X2apic mode: setup the INTX registers on mask/unmask
+    - iommu/amd: X2apic mode: mask/unmask interrupts on suspend/resume
+    - iommu/amd: Remove useless irq affinity notifier
+    - ASoC: Intel: catpt: Test dmaengine_submit() result before moving on
+    - iommu/iova: Fix race between FQ timeout and teardown
+    - ASoC: mediatek: mt8195: correct default value
+    - of: fdt: Aggregate the processing of "linux,usable-memory-range"
+    - efi: apply memblock cap after memblock_add()
+    - scsi: block: pm: Always set request queue runtime active in
+      blk_post_runtime_resume()
+    - phy: uniphier-usb3ss: fix unintended writing zeros to PHY register
+    - ASoC: mediatek: Check for error clk pointer
+    - powerpc/64s: Mask NIP before checking against SRR0
+    - powerpc/64s: Use EMIT_WARN_ENTRY for SRR debug warnings
+    - phy: cadence: Sierra: Fix to get correct parent for mux clocks
+    - ASoC: samsung: idma: Check of ioremap return value
+    - misc: lattice-ecp3-config: Fix task hung when firmware load failed
+    - ASoC: mediatek: mt8195: correct pcmif BE dai control flow
+    - arm64: tegra: Remove non existent Tegra194 reset
+    - mips: lantiq: add support for clk_set_parent()
+    - mips: bcm63xx: add support for clk_set_parent()
+    - powerpc/xive: Add missing null check after calling kmalloc
+    - ASoC: fsl_mqs: fix MODULE_ALIAS
+    - ALSA: hda/cs8409: Increase delay during jack detection
+    - ALSA: hda/cs8409: Fix Jack detection after resume
+    - RDMA/cxgb4: Set queue pair state when being queried
+    - clk: qcom: gcc-sc7280: Mark gcc_cfg_noc_lpass_clk always enabled
+    - ASoC: imx-card: Need special setting for ak4497 on i.MX8MQ
+    - ASoC: imx-card: Fix mclk calculation issue for akcodec
+    - ASoC: imx-card: improve the sound quality for low rate
+    - ASoC: fsl_asrc: refine the check of available clock divider
+    - clk: bm1880: remove kfrees on static allocations
+    - of: base: Fix phandle argument length mismatch error message
+    - of/fdt: Don't worry about non-memory region overlap for no-map
+    - MIPS: boot/compressed/: add __ashldi3 to target for ZSTD compression
+    - MIPS: compressed: Fix build with ZSTD compression
+    - mailbox: fix gce_num of mt8192 driver data
+    - ARM: dts: omap3-n900: Fix lp5523 for multi color
+    - leds: lp55xx: initialise output direction from dts
+    - Bluetooth: Fix debugfs entry leak in hci_register_dev()
+    - Bluetooth: Fix memory leak of hci device
+    - drm/panel: Delete panel on mipi_dsi_attach() failure
+    - Bluetooth: Fix removing adv when processing cmd complete
+    - fs: dlm: filter user dlm messages for kernel locks
+    - drm/lima: fix warning when CONFIG_DEBUG_SG=y & CONFIG_DMA_API_DEBUG=y
+    - selftests/bpf: Fix memory leaks in btf_type_c_dump() helper
+    - selftests/bpf: Destroy XDP link correctly
+    - selftests/bpf: Fix bpf_object leak in skb_ctx selftest
+    - ar5523: Fix null-ptr-deref with unexpected WDCMSG_TARGET_START reply
+    - drm/bridge: dw-hdmi: handle ELD when DRM_BRIDGE_ATTACH_NO_CONNECTOR
+    - drm/nouveau/pmu/gm200-: avoid touching PMU outside of DEVINIT/PREOS/ACR
+    - media: atomisp: fix try_fmt logic
+    - media: atomisp: set per-device's default mode
+    - media: atomisp-ov2680: Fix ov2680_set_fmt() clobbering the exposure
+    - media: atomisp: check before deference asd variable
+    - ARM: shmobile: rcar-gen2: Add missing of_node_put()
+    - batman-adv: allow netlink usage in unprivileged containers
+    - media: atomisp: handle errors at sh_css_create_isp_params()
+    - ath11k: Fix crash caused by uninitialized TX ring
+    - usb: dwc3: meson-g12a: fix shared reset control use
+    - USB: ehci_brcm_hub_control: Improve port index sanitizing
+    - usb: gadget: f_fs: Use stream_open() for endpoint files
+    - psi: Fix PSI_MEM_FULL state when tasks are in memstall and doing reclaim
+    - drm: panel-orientation-quirks: Add quirk for the Lenovo Yoga Book X91F/L
+    - HID: magicmouse: Report battery level over USB
+    - HID: apple: Do not reset quirks when the Fn key is not found
+    - media: b2c2: Add missing check in flexcop_pci_isr:
+    - libbpf: Accommodate DWARF/compiler bug with duplicated structs
+    - ethernet: renesas: Use div64_ul instead of do_div
+    - EDAC/synopsys: Use the quirk for version instead of ddr version
+    - arm64: dts: qcom: sm8350: Shorten camera-thermal-bottom name
+    - soc: imx: gpcv2: Synchronously suspend MIX domains
+    - ARM: imx: rename DEBUG_IMX21_IMX27_UART to DEBUG_IMX27_UART
+    - drm/amd/display: check top_pipe_to_program pointer
+    - drm/amdgpu/display: set vblank_disable_immediate for DC
+    - soc: ti: pruss: fix referenced node in error message
+    - mlxsw: pci: Add shutdown method in PCI driver
+    - drm/amd/display: add else to avoid double destroy clk_mgr
+    - drm/bridge: megachips: Ensure both bridges are probed before registration
+    - mxser: keep only !tty test in ISR
+    - tty: serial: imx: disable UCR4_OREN in .stop_rx() instead of .shutdown()
+    - gpiolib: acpi: Do not set the IRQ type if the IRQ is already in use
+    - HSI: core: Fix return freed object in hsi_new_client
+    - crypto: jitter - consider 32 LSB for APT
+    - mwifiex: Fix skb_over_panic in mwifiex_usb_recv()
+    - rsi: Fix use-after-free in rsi_rx_done_handler()
+    - rsi: Fix out-of-bounds read in rsi_read_pkt()
+    - ath11k: Avoid NULL ptr access during mgmt tx cleanup
+    - media: venus: avoid calling core_clk_setrate() concurrently during
+      concurrent video sessions
+    - regulator: da9121: Prevent current limit change when enabled
+    - drm/vmwgfx: Release ttm memory if probe fails
+    - drm/vmwgfx: Introduce a new placement for MOB page tables
+    - ACPI / x86: Drop PWM2 device on Lenovo Yoga Book from always present table
+    - ACPI: Change acpi_device_always_present() into acpi_device_override_status()
+    - ACPI / x86: Allow specifying acpi_device_override_status() quirks by path
+    - ACPI / x86: Add not-present quirk for the PCI0.SDHB.BRC1 device on the GPD
+      win
+    - arm64: dts: ti: j7200-main: Fix 'dtbs_check' serdes_ln_ctrl node
+    - arm64: dts: ti: j721e-main: Fix 'dtbs_check' in serdes_ln_ctrl node
+    - usb: uhci: add aspeed ast2600 uhci support
+    - floppy: Add max size check for user space request
+    - x86/mm: Flush global TLB when switching to trampoline page-table
+    - drm: rcar-du: Fix CRTC timings when CMM is used
+    - media: uvcvideo: Increase UVC_CTRL_CONTROL_TIMEOUT to 5 seconds.
+    - media: rcar-vin: Update format alignment constraints
+    - media: saa7146: hexium_orion: Fix a NULL pointer dereference in
+      hexium_attach()
+    - media: atomisp: fix "variable dereferenced before check 'asd'"
+    - media: m920x: don't use stack on USB reads
+    - thunderbolt: Runtime PM activate both ends of the device link
+    - arm64: dts: renesas: Fix thermal bindings
+    - iwlwifi: mvm: synchronize with FW after multicast commands
+    - iwlwifi: mvm: avoid clearing a just saved session protection id
+    - rcutorture: Avoid soft lockup during cpu stall
+    - ath11k: avoid deadlock by change ieee80211_queue_work for regd_update_work
+    - ath10k: Fix tx hanging
+    - net-sysfs: update the queue counts in the unregistration path
+    - net: phy: prefer 1000baseT over 1000baseKX
+    - gpio: aspeed: Convert aspeed_gpio.lock to raw_spinlock
+    - gpio: aspeed-sgpio: Convert aspeed_sgpio.lock to raw_spinlock
+    - selftests/ftrace: make kprobe profile testcase description unique
+    - ath11k: Avoid false DEADLOCK warning reported by lockdep
+    - ARM: dts: qcom: sdx55: fix IPA interconnect definitions
+    - x86/mce: Allow instrumentation during task work queueing
+    - x86/mce: Mark mce_panic() noinstr
+    - x86/mce: Mark mce_end() noinstr
+    - x86/mce: Mark mce_read_aux() noinstr
+    - net: bonding: debug: avoid printing debug logs when bond is not notifying
+      peers
+    - kunit: Don't crash if no parameters are generated
+    - bpf: Do not WARN in bpf_warn_invalid_xdp_action()
+    - drm/amdkfd: Fix error handling in svm_range_add
+    - HID: quirks: Allow inverting the absolute X/Y values
+    - HID: i2c-hid-of: Expose the touchscreen-inverted properties
+    - media: igorplugusb: receiver overflow should be reported
+    - media: rockchip: rkisp1: use device name for debugfs subdir name
+    - media: saa7146: hexium_gemini: Fix a NULL pointer dereference in
+      hexium_attach()
+    - mmc: tmio: reinit card irqs in reset routine
+    - mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIO
+    - drm/amd/amdgpu: fix psp tmr bo pin count leak in SRIOV
+    - drm/amd/amdgpu: fix gmc bo pin count leak in SRIOV
+    - audit: ensure userspace is penalized the same as the kernel when under
+      pressure
+    - arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus
+    - arm64: tegra: Adjust length of CCPLEX cluster MMIO region
+    - crypto: ccp - Move SEV_INIT retry for corrupted data
+    - crypto: hisilicon/hpre - fix memory leak in hpre_curve25519_src_init()
+    - PM: runtime: Add safety net to supplier device release
+    - cpufreq: Fix initialization of min and max frequency QoS requests
+    - mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()
+    - mt76: do not pass the received frame with decryption error
+    - mt76: mt7615: improve wmm index allocation
+    - ath9k_htc: fix NULL pointer dereference at ath9k_htc_rxep()
+    - ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()
+    - ath9k: Fix out-of-bound memcpy in ath9k_hif_usb_rx_stream
+    - rtw88: 8822c: update rx settings to prevent potential hw deadlock
+    - PM: AVS: qcom-cpr: Use div64_ul instead of do_div
+    - iwlwifi: fix leaks/bad data after failed firmware load
+    - iwlwifi: remove module loading failure message
+    - iwlwifi: mvm: Fix calculation of frame length
+    - iwlwifi: mvm: fix AUX ROC removal
+    - iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
+    - mmc: sdhci-pci-gli: GL9755: Support for CD/WP inversion on OF platforms
+    - block: check minor range in device_add_disk()
+    - um: registers: Rename function names to avoid conflicts and build problems
+    - ath11k: Fix napi related hang
+    - Bluetooth: btintel: Add missing quirks and msft ext for legacy bootloader
+    - Bluetooth: vhci: Set HCI_QUIRK_VALID_LE_STATES
+    - xfrm: rate limit SA mapping change message to user space
+    - drm/etnaviv: consider completed fence seqno in hang check
+    - jffs2: GC deadlock reading a page that is used in jffs2_write_begin()
+    - ACPICA: actypes.h: Expand the ACPI_ACCESS_ definitions
+    - ACPICA: Utilities: Avoid deleting the same object twice in a row
+    - ACPICA: Executer: Fix the REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
+    - ACPICA: Fix wrong interpretation of PCC address
+    - ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5
+    - mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling
+    - drm/amdgpu: fixup bad vram size on gmc v8
+    - amdgpu/pm: Make sysfs pm attributes as read-only for VFs
+    - ACPI: battery: Add the ThinkPad "Not Charging" quirk
+    - ACPI: CPPC: Check present CPUs for determining _CPC is valid
+    - btrfs: remove BUG_ON() in find_parent_nodes()
+    - btrfs: remove BUG_ON(!eie) in find_parent_nodes
+    - net: mdio: Demote probed message to debug print
+    - mac80211: allow non-standard VHT MCS-10/11
+    - dm btree: add a defensive bounds check to insert_at()
+    - dm space map common: add bounds check to sm_ll_lookup_bitmap()
+    - bpf/selftests: Fix namespace mount setup in tc_redirect
+    - mlxsw: pci: Avoid flow control for EMAD packets
+    - net: phy: marvell: configure RGMII delays for 88E1118
+    - net: gemini: allow any RGMII interface mode
+    - regulator: qcom_smd: Align probe function with rpmh-regulator
+    - serial: pl010: Drop CR register reset on set_termios
+    - serial: pl011: Drop CR register reset on set_termios
+    - serial: core: Keep mctrl register state and cached copy in sync
+    - random: do not throw away excess input to crng_fast_load
+    - net/mlx5: Update log_max_qp value to FW max capability
+    - net/mlx5e: Unblock setting vid 0 for VF in case PF isn't eswitch manager
+    - parisc: Avoid calling faulthandler_disabled() twice
+    - can: flexcan: allow to change quirks at runtime
+    - can: flexcan: rename RX modes
+    - can: flexcan: add more quirks to describe RX path capabilities
+    - x86/kbuild: Enable CONFIG_KALLSYMS_ALL=y in the defconfigs
+    - powerpc/6xx: add missing of_node_put
+    - powerpc/powernv: add missing of_node_put
+    - powerpc/cell: add missing of_node_put
+    - powerpc/btext: add missing of_node_put
+    - powerpc/watchdog: Fix missed watchdog reset due to memory ordering race
+    - ASoC: imx-hdmi: add put_device() after of_find_device_by_node()
+    - i2c: i801: Don't silently correct invalid transfer size
+    - powerpc/smp: Move setup_profiling_timer() under CONFIG_PROFILING
+    - i2c: mpc: Correct I2C reset procedure
+    - clk: meson: gxbb: Fix the SDM_EN bit for MPLL0 on GXBB
+    - powerpc/powermac: Add missing lockdep_register_key()
+    - KVM: PPC: Book3S: Suppress warnings when allocating too big memory slots
+    - KVM: PPC: Book3S: Suppress failed alloc warning in H_COPY_TOFROM_GUEST
+    - w1: Misuse of get_user()/put_user() reported by sparse
+    - nvmem: core: set size for sysfs bin file
+    - dm: fix alloc_dax error handling in alloc_dev
+    - interconnect: qcom: rpm: Prevent integer overflow in rate
+    - scsi: ufs: Fix a kernel crash during shutdown
+    - scsi: lpfc: Fix leaked lpfc_dmabuf mbox allocations with NPIV
+    - scsi: lpfc: Trigger SLI4 firmware dump before doing driver cleanup
+    - ALSA: seq: Set upper limit of processed events
+    - MIPS: Loongson64: Use three arguments for slti
+    - powerpc/40x: Map 32Mbytes of memory at startup
+    - selftests/powerpc/spectre_v2: Return skip code when miss_percent is high
+    - powerpc: handle kdump appropriately with crash_kexec_post_notifiers option
+    - powerpc/fadump: Fix inaccurate CPU state info in vmcore generated with panic
+    - udf: Fix error handling in udf_new_inode()
+    - MIPS: OCTEON: add put_device() after of_find_device_by_node()
+    - irqchip/gic-v4: Disable redistributors' view of the VPE table at boot time
+    - i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
+    - selftests/powerpc: Add a test of sigreturning to the kernel
+    - MIPS: Octeon: Fix build errors using clang
+    - scsi: sr: Don't use GFP_DMA
+    - scsi: mpi3mr: Fixes around reply request queues
+    - ASoC: mediatek: mt8192-mt6359: fix device_node leak
+    - phy: phy-mtk-tphy: add support efuse setting
+    - ASoC: mediatek: mt8173: fix device_node leak
+    - ASoC: mediatek: mt8183: fix device_node leak
+    - habanalabs: skip read fw errors if dynamic descriptor invalid
+    - phy: mediatek: Fix missing check in mtk_mipi_tx_probe
+    - mailbox: change mailbox-mpfs compatible string
+    - seg6: export get_srh() for ICMP handling
+    - icmp: ICMPV6: Examine invoking packet for Segment Route Headers.
+    - udp6: Use Segment Routing Header for dest address if present
+    - rpmsg: core: Clean up resources on announce_create failure.
+    - ifcvf/vDPA: fix misuse virtio-net device config size for blk dev
+    - crypto: omap-aes - Fix broken pm_runtime_and_get() usage
+    - crypto: stm32/crc32 - Fix kernel BUG triggered in probe()
+    - crypto: caam - replace this_cpu_ptr with raw_cpu_ptr
+    - ubifs: Error path in ubifs_remount_rw() seems to wrongly free write buffers
+    - tpm: fix potential NULL pointer access in tpm_del_char_device
+    - tpm: fix NPE on probe for missing device
+    - mfd: tps65910: Set PWR_OFF bit during driver probe
+    - spi: uniphier: Fix a bug that doesn't point to private data correctly
+    - xen/gntdev: fix unmap notification order
+    - md: Move alloc/free acct bioset in to personality
+    - HID: magicmouse: Fix an error handling path in magicmouse_probe()
+    - fuse: Pass correct lend value to filemap_write_and_wait_range()
+    - serial: Fix incorrect rs485 polarity on uart open
+    - cputime, cpuacct: Include guest time in user time in cpuacct.stat
+    - sched/cpuacct: Fix user/system in shown cpuacct.usage*
+    - tracing/kprobes: 'nmissed' not showed correctly for kretprobe
+    - tracing: Have syscall trace events use trace_event_buffer_lock_reserve()
+    - remoteproc: imx_rproc: Fix a resource leak in the remove function
+    - iwlwifi: mvm: Increase the scan timeout guard to 30 seconds
+    - s390/mm: fix 2KB pgtable release race
+    - device property: Fix fwnode_graph_devcon_match() fwnode leak
+    - drm/tegra: submit: Add missing pm_runtime_mark_last_busy()
+    - drm/etnaviv: limit submit sizes
+    - drm/amd/display: Fix the uninitialized variable in enable_stream_features()
+    - drm/nouveau/kms/nv04: use vzalloc for nv04_display
+    - drm/bridge: analogix_dp: Make PSR-exit block less
+    - parisc: Fix lpa and lpa_user defines
+    - powerpc/64s/radix: Fix huge vmap false positive
+    - scsi: lpfc: Fix lpfc_force_rscn ndlp kref imbalance
+    - drm/amdgpu: don't do resets on APUs which don't support it
+    - drm/i915/display/ehl: Update voltage swing table
+    - PCI: xgene: Fix IB window setup
+    - PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
+    - PCI: pci-bridge-emul: Make expansion ROM Base Address register read-only
+    - PCI: pci-bridge-emul: Properly mark reserved PCIe bits in PCI config space
+    - PCI: pci-bridge-emul: Fix definitions of reserved bits
+    - PCI: pci-bridge-emul: Correctly set PCIe capabilities
+    - PCI: pci-bridge-emul: Set PCI_STATUS_CAP_LIST for PCIe device
+    - xfrm: fix policy lookup for ipv6 gre packets
+    - xfrm: fix dflt policy check when there is no policy configured
+    - btrfs: fix deadlock between quota enable and other quota operations
+    - btrfs: check the root node for uptodate before returning it
+    - btrfs: respect the max size in the header when activating swap file
+    - ext4: make sure to reset inode lockdep class when quota enabling fails
+    - ext4: make sure quota gets properly shutdown on error
+    - ext4: fix a possible ABBA deadlock due to busy PA
+    - ext4: initialize err_blk before calling __ext4_get_inode_loc
+    - ext4: fix fast commit may miss tracking range for FALLOC_FL_ZERO_RANGE
+    - ext4: set csum seed in tmp inode while migrating to extents
+    - ext4: Fix BUG_ON in ext4_bread when write quota data
+    - ext4: use ext4_ext_remove_space() for fast commit replay delete range
+    - ext4: fast commit may miss tracking unwritten range during ftruncate
+    - ext4: destroy ext4_fc_dentry_cachep kmemcache on module removal
+    - ext4: fix null-ptr-deref in '__ext4_journal_ensure_credits'
+    - ext4: fix an use-after-free issue about data=journal writeback mode
+    - ext4: don't use the orphan list when migrating an inode
+    - tracing/osnoise: Properly unhook events if start_per_cpu_kthreads() fails
+    - ath11k: qmi: avoid error messages when dma allocation fails
+    - drm/radeon: fix error handling in radeon_driver_open_kms
+    - of: base: Improve argument length mismatch error
+    - firmware: Update Kconfig help text for Google firmware
+    - can: mcp251xfd: mcp251xfd_tef_obj_read(): fix typo in error message
+    - media: rcar-csi2: Optimize the selection PHTW register
+    - drm/vc4: hdmi: Make sure the device is powered with CEC
+    - media: correct MEDIA_TEST_SUPPORT help text
+    - Documentation: coresight: Fix documentation issue
+    - Documentation: dmaengine: Correctly describe dmatest with channel unset
+    - Documentation: ACPI: Fix data node reference documentation
+    - Documentation, arch: Remove leftovers from raw device
+    - Documentation, arch: Remove leftovers from CIFS_WEAK_PW_HASH
+    - Documentation: refer to config RANDOMIZE_BASE for kernel address-space
+      randomization
+    - Documentation: fix firewire.rst ABI file path error
+    - net: usb: Correct reset handling of smsc95xx
+    - Bluetooth: hci_sync: Fix not setting adv set duration
+    - scsi: core: Show SCMD_LAST in text form
+    - scsi: ufs: ufs-mediatek: Fix error checking in ufs_mtk_init_va09_pwr_ctrl()
+    - RDMA/cma: Remove open coding of overflow checking for private_data_len
+    - dmaengine: uniphier-xdmac: Fix type of address variables
+    - dmaengine: idxd: fix wq settings post wq disable
+    - RDMA/hns: Modify the mapping attribute of doorbell to device
+    - RDMA/rxe: Fix a typo in opcode name
+    - dmaengine: stm32-mdma: fix STM32_MDMA_CTBR_TSEL_MASK
+    - Revert "net/mlx5: Add retry mechanism to the command entry index allocation"
+    - powerpc/cell: Fix clang -Wimplicit-fallthrough warning
+    - powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses
+    - block: fix async_depth sysfs interface for mq-deadline
+    - block: Fix fsync always failed if once failed
+    - drm/vc4: crtc: Drop feed_txp from state
+    - drm/vc4: Fix non-blocking commit getting stuck forever
+    - drm/vc4: crtc: Copy assigned channel to the CRTC
+    - bpftool: Remove inclusion of utilities.mak from Makefiles
+    - bpftool: Fix indent in option lists in the documentation
+    - xdp: check prog type before updating BPF link
+    - bpf: Fix mount source show for bpffs
+    - bpf: Mark PTR_TO_FUNC register initially with zero offset
+    - perf evsel: Override attr->sample_period for non-libpfm4 events
+    - ipv4: update fib_info_cnt under spinlock protection
+    - ipv4: avoid quadratic behavior in netns dismantle
+    - mlx5: Don't accidentally set RTO_ONLINK before mlx5e_route_lookup_ipv4_get()
+    - net/fsl: xgmac_mdio: Add workaround for erratum A-009885
+    - net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module
+    - parisc: pdc_stable: Fix memory leak in pdcs_register_pathentries
+    - riscv: dts: microchip: mpfs: Drop empty chosen node
+    - drm/vmwgfx: Remove explicit transparent hugepages support
+    - drm/vmwgfx: Remove unused compile options
+    - f2fs: fix remove page failed in invalidate compress pages
+    - f2fs: fix to avoid panic in is_alive() if metadata is inconsistent
+    - f2fs: compress: fix potential deadlock of compress file
+    - f2fs: fix to reserve space for IO align feature
+    - f2fs: fix to check available space of CP area correctly in
+      update_ckpt_flags()
+    - crypto: octeontx2 - uninitialized variable in kvf_limits_store()
+    - af_unix: annote lockless accesses to unix_tot_inflight & gc_in_progress
+    - clk: Emit a stern warning with writable debugfs enabled
+    - clk: si5341: Fix clock HW provider cleanup
+    - pinctrl/rockchip: fix gpio device creation
+    - gpio: mpc8xxx: Fix IRQ check in mpc8xxx_probe
+    - gpio: idt3243x: Fix IRQ check in idt_gpio_probe
+    - net/smc: Fix hung_task when removing SMC-R devices
+    - net: axienet: increase reset timeout
+    - net: axienet: Wait for PhyRstCmplt after core reset
+    - net: axienet: reset core on initialization prior to MDIO access
+    - net: axienet: add missing memory barriers
+    - net: axienet: limit minimum TX ring size
+    - net: axienet: Fix TX ring slot available check
+    - net: axienet: fix number of TX ring slots for available check
+    - net: axienet: fix for TX busy handling
+    - net: axienet: increase default TX ring size to 128
+    - bitops: protect find_first_{,zero}_bit properly
+    - um: gitignore: Add kernel/capflags.c
+    - HID: vivaldi: fix handling devices not using numbered reports
+    - rtc: pxa: fix null pointer dereference
+    - vdpa/mlx5: Fix wrong configuration of virtio_version_1_0
+    - virtio_ring: mark ring unused on error
+    - taskstats: Cleanup the use of task->exit_code
+    - inet: frags: annotate races around fqdir->dead and fqdir->high_thresh
+    - netns: add schedule point in ops_exit_list()
+    - iwlwifi: fix Bz NMI behaviour
+    - xfrm: Don't accidentally set RTO_ONLINK in decode_session4()
+    - vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
+    - gre: Don't accidentally set RTO_ONLINK in gre_fill_metadata_dst()
+    - libcxgb: Don't accidentally set RTO_ONLINK in cxgb_find_route()
+    - perf script: Fix hex dump character output
+    - dmaengine: at_xdmac: Don't start transactions at tx_submit level
+    - dmaengine: at_xdmac: Start transfer for cyclic channels in issue_pending
+    - dmaengine: at_xdmac: Print debug message after realeasing the lock
+    - dmaengine: at_xdmac: Fix concurrency over xfers_list
+    - dmaengine: at_xdmac: Fix lld view setting
+    - dmaengine: at_xdmac: Fix at_xdmac_lld struct definition
+    - perf tools: Drop requirement for libstdc++.so for libopencsd check
+    - perf probe: Fix ppc64 'perf probe add events failed' case
+    - devlink: Remove misleading internal_flags from health reporter dump
+    - arm64: dts: qcom: msm8996: drop not documented adreno properties
+    - net: fix sock_timestamping_bind_phc() to release device
+    - net: bonding: fix bond_xmit_broadcast return value error bug
+    - net: ipa: fix atomic update in ipa_endpoint_replenish()
+    - net_sched: restore "mpu xxx" handling
+    - net: mscc: ocelot: don't let phylink re-enable TX PAUSE on the NPI port
+    - bcmgenet: add WOL IRQ check
+    - net: wwan: Fix MRU mismatch issue which may lead to data connection lost
+    - net: ethernet: mtk_eth_soc: fix error checking in mtk_mac_config()
+    - net: ocelot: Fix the call to switchdev_bridge_port_offload
+    - net: sfp: fix high power modules without diagnostic monitoring
+    - net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
+    - net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices
+    - net: mscc: ocelot: fix using match before it is set
+    - dt-bindings: display: meson-dw-hdmi: add missing sound-name-prefix property
+    - dt-bindings: display: meson-vpu: Add missing amlogic,canvas property
+    - dt-bindings: watchdog: Require samsung,syscon-phandle for Exynos7
+    - sch_api: Don't skip qdisc attach on ingress
+    - scripts/dtc: dtx_diff: remove broken example from help text
+    - lib82596: Fix IRQ check in sni_82596_probe
+    - mm/hmm.c: allow VM_MIXEDMAP to work with hmm_range_fault
+    - bonding: Fix extraction of ports from the packet headers
+    - lib/test_meminit: destroy cache in kmem_cache_alloc_bulk() test
+    - scripts: sphinx-pre-install: add required ctex dependency
+    - scripts: sphinx-pre-install: Fix ctex support on Debian
+    - Linux 5.15.17
+
+  * rtw88_8821ce causes freeze (LP: #1927808) // Jammy update: v5.15.17 upstream
+    stable release (LP: #1959376)
+    - rtw88: Disable PCIe ASPM while doing NAPI poll on 8821CE
+
+  * Jammy update: v5.15.16 upstream stable release (LP: #1958977)
+    - devtmpfs regression fix: reconfigure on each mount
+    - orangefs: Fix the size of a memory allocation in orangefs_bufmap_alloc()
+    - remoteproc: qcom: pil_info: Don't memcpy_toio more than is provided
+    - perf: Protect perf_guest_cbs with RCU
+    - KVM: x86: Register perf callbacks after calling vendor's hardware_setup()
+    - KVM: x86: Register Processor Trace interrupt hook iff PT enabled in guest
+    - KVM: x86: don't print when fail to read/write pv eoi memory
+    - KVM: s390: Clarify SIGP orders versus STOP/RESTART
+    - remoteproc: qcom: pas: Add missing power-domain "mxc" for CDSP
+    - 9p: only copy valid iattrs in 9P2000.L setattr implementation
+    - video: vga16fb: Only probe for EGA and VGA 16 color graphic cards
+    - media: uvcvideo: fix division by zero at stream start
+    - rtlwifi: rtl8192cu: Fix WARNING when calling local_irq_restore() with
+      interrupts enabled
+    - firmware: qemu_fw_cfg: fix sysfs information leak
+    - firmware: qemu_fw_cfg: fix NULL-pointer deref on duplicate entries
+    - firmware: qemu_fw_cfg: fix kobject leak in probe error path
+    - perf annotate: Avoid TUI crash when navigating in the annotation of
+      recursive functions
+    - KVM: x86: remove PMU FIXED_CTR3 from msrs_to_save_all
+    - ALSA: hda/realtek: Add speaker fixup for some Yoga 15ITL5 devices
+    - ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master after
+      reboot from Windows
+    - ALSA: hda: ALC287: Add Lenovo IdeaPad Slim 9i 14ITL5 speaker quirk
+    - ALSA: hda/tegra: Fix Tegra194 HDA reset failure
+    - ALSA: hda/realtek: Add quirk for Legion Y9000X 2020
+    - ALSA: hda/realtek: Re-order quirk entries for Lenovo
+    - mtd: fixup CFI on ixp4xx
+    - Linux 5.15.16
+
+  * UBSAN: array-index-out-of-bounds in dcn31_resources on AMD yellow carp
+    platform (LP: #1958229)
+    - drm/amd/display: Fix out of bounds access on DNC31 stream encoder regs
+
+  * Jammy update: v5.15.15 upstream stable release (LP: #1958418)
+    - s390/kexec: handle R_390_PLT32DBL rela in arch_kexec_apply_relocations_add()
+    - workqueue: Fix unbind_workers() VS wq_worker_running() race
+    - staging: r8188eu: switch the led off during deinit
+    - bpf: Fix out of bounds access from invalid *_or_null type verification
+    - Bluetooth: btusb: Add protocol for MediaTek bluetooth devices(MT7922)
+    - Bluetooth: btusb: Add the new support ID for Realtek RTL8852A
+    - Bluetooth: btusb: Add support for IMC Networks Mediatek Chip(MT7921)
+    - Bbluetooth: btusb: Add another Bluetooth part for Realtek 8852AE
+    - Bluetooth: btusb: fix memory leak in btusb_mtk_submit_wmt_recv_urb()
+    - Bluetooth: btusb: enable Mediatek to support AOSP extension
+    - Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
+    - fget: clarify and improve __fget_files() implementation
+    - Bluetooth: btusb: Add two more Bluetooth parts for WCN6855
+    - Bluetooth: btusb: Add support for Foxconn MT7922A
+    - Bluetooth: btintel: Fix broken LED quirk for legacy ROM devices
+    - Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0
+    - Bluetooth: bfusb: fix division by zero in send path
+    - ARM: dts: exynos: Fix BCM4330 Bluetooth reset polarity in I9100
+    - USB: core: Fix bug in resuming hub's handling of wakeup requests
+    - USB: Fix "slab-out-of-bounds Write" bug in usb_hcd_poll_rh_status
+    - ath11k: Fix buffer overflow when scanning with extraie
+    - mmc: sdhci-pci: Add PCI ID for Intel ADL
+    - Bluetooth: add quirk disabling LE Read Transmit Power
+    - Bluetooth: btbcm: disable read tx power for some Macs with the T2 Security
+      chip
+    - Bluetooth: btbcm: disable read tx power for MacBook Air 8,1 and 8,2
+    - veth: Do not record rx queue hint in veth_xmit
+    - mfd: intel-lpss: Fix too early PM enablement in the ACPI ->probe()
+    - can: gs_usb: fix use of uninitialized variable, detach device on reception
+      of invalid USB data
+    - can: isotp: convert struct tpcon::{idx,len} to unsigned int
+    - can: gs_usb: gs_can_start_xmit(): zero-initialize hf->{flags,reserved}
+    - random: fix data race on crng_node_pool
+    - random: fix data race on crng init time
+    - random: fix crash on multiple early calls to add_bootloader_randomness()
+    - platform/x86/intel: hid: add quirk to support Surface Go 3
+    - media: Revert "media: uvcvideo: Set unique vdev name based in type"
+    - staging: wlan-ng: Avoid bitwise vs logical OR warning in
+      hfa384x_usb_throttlefn()
+    - drm/i915: Avoid bitwise vs logical OR warning in snb_wm_latency_quirk()
+    - staging: greybus: fix stack size warning with UBSAN
+    - Linux 5.15.15
+
+  * UBSAN warning on unplugging USB4 DP alt mode from AMD Yellow Carp graphics
+    card (LP: #1956497)
+    - drm/amd/display: explicitly set is_dsc_supported to false before use
+
+  * Support USB4 DP alt mode for AMD Yellow Carp graphics card (LP: #1953008)
+    - drm/amd/display: Enable PSR by default on newer DCN
+    - SAUCE: drm/amd/display: Fixup previous PSR policy commit
+    - drm/amd/display: Fix USB4 hot plug crash issue
+    - drm/amd/display: Creating a fw boot options bit for an upcoming feature
+    - drm/amd/display: Enable dpia in dmub only for DCN31 B0
+    - drm/amd/display: MST support for DPIA
+    - drm/amd/display: Set phy_mux_sel bit in dmub scratch register
+    - drm/amd/display: Don't lock connection_mutex for DMUB HPD
+    - drm/amd/display: Add callbacks for DMUB HPD IRQ notifications
+
+  * Jammy update: v5.15.14 upstream stable release (LP: #1957882)
+    - fscache_cookie_enabled: check cookie is valid before accessing it
+    - selftests: x86: fix [-Wstringop-overread] warn in test_process_vm_readv()
+    - tracing: Fix check for trace_percpu_buffer validity in get_trace_buf()
+    - tracing: Tag trace_percpu_buffer as a percpu pointer
+    - Revert "RDMA/mlx5: Fix releasing unallocated memory in dereg MR flow"
+    - ieee802154: atusb: fix uninit value in atusb_set_extended_addr
+    - i40e: Fix to not show opcode msg on unsuccessful VF MAC change
+    - iavf: Fix limit of total number of queues to active queues of VF
+    - RDMA/core: Don't infoleak GRH fields
+    - Revert "net: usb: r8152: Add MAC passthrough support for more Lenovo Docks"
+    - netrom: fix copying in user data in nr_setsockopt
+    - RDMA/uverbs: Check for null return of kmalloc_array
+    - mac80211: initialize variable have_higher_than_11mbit
+    - mac80211: mesh: embedd mesh_paths and mpp_paths into ieee80211_if_mesh
+    - sfc: The RX page_ring is optional
+    - i40e: fix use-after-free in i40e_sync_filters_subtask()
+    - i40e: Fix for displaying message regarding NVM version
+    - i40e: Fix incorrect netdev's real number of RX/TX queues
+    - ftrace/samples: Add missing prototypes direct functions
+    - ipv4: Check attribute length for RTA_GATEWAY in multipath route
+    - ipv4: Check attribute length for RTA_FLOW in multipath route
+    - ipv6: Check attribute length for RTA_GATEWAY in multipath route
+    - ipv6: Check attribute length for RTA_GATEWAY when deleting multipath route
+    - lwtunnel: Validate RTA_ENCAP_TYPE attribute length
+    - selftests: net: udpgro_fwd.sh: explicitly checking the available ping
+      feature
+    - sctp: hold endpoint before calling cb in sctp_transport_lookup_process
+    - batman-adv: mcast: don't send link-local multicast to mcast routers
+    - sch_qfq: prevent shift-out-of-bounds in qfq_init_qdisc
+    - net: ena: Fix undefined state when tx request id is out of bounds
+    - net: ena: Fix wrong rx request id by resetting device
+    - net: ena: Fix error handling when calculating max IO queues number
+    - md/raid1: fix missing bitmap update w/o WriteMostly devices
+    - EDAC/i10nm: Release mdev/mbase when failing to detect HBM
+    - KVM: x86: Check for rmaps allocation
+    - cgroup: Use open-time credentials for process migraton perm checks
+    - cgroup: Allocate cgroup_file_ctx for kernfs_open_file->priv
+    - cgroup: Use open-time cgroup namespace for process migration perm checks
+    - Revert "i2c: core: support bus regulator controlling in adapter"
+    - i2c: mpc: Avoid out of bounds memory access
+    - power: supply: core: Break capacity loop
+    - power: reset: ltc2952: Fix use of floating point literals
+    - reset: renesas: Fix Runtime PM usage
+    - rndis_host: support Hytera digital radios
+    - gpio: gpio-aspeed-sgpio: Fix wrong hwirq base in irq handler
+    - net ticp:fix a kernel-infoleak in __tipc_sendmsg()
+    - phonet: refcount leak in pep_sock_accep
+    - fbdev: fbmem: add a helper to determine if an aperture is used by a fw fb
+    - drm/amdgpu: disable runpm if we are the primary adapter
+    - power: bq25890: Enable continuous conversion for ADC at charging
+    - ipv6: Continue processing multipath route even if gateway attribute is
+      invalid
+    - ipv6: Do cleanup if attribute validation fails in multipath route
+    - auxdisplay: charlcd: checking for pointer reference before dereferencing
+    - drm/amdgpu: fix dropped backing store handling in amdgpu_dma_buf_move_notify
+    - drm/amd/pm: Fix xgmi link control on aldebaran
+    - usb: mtu3: fix interval value for intr and isoc
+    - scsi: libiscsi: Fix UAF in iscsi_conn_get_param()/iscsi_conn_teardown()
+    - ip6_vti: initialize __ip6_tnl_parm struct in vti6_siocdevprivate
+    - net: udp: fix alignment problem in udp4_seq_show()
+    - atlantic: Fix buff_ring OOB in aq_ring_rx_clean
+    - drm/amd/pm: skip setting gfx cgpg in the s0ix suspend-resume
+    - mISDN: change function names to avoid conflicts
+    - drm/amd/display: fix B0 TMDS deepcolor no dislay issue
+    - drm/amd/display: Added power down for DCN10
+    - ipv6: raw: check passed optlen before reading
+    - userfaultfd/selftests: fix hugetlb area allocations
+    - ARM: dts: gpio-ranges property is now required
+    - Input: zinitix - make sure the IRQ is allocated before it gets enabled
+    - Revert "drm/amdgpu: stop scheduler when calling hw_fini (v2)"
+    - drm/amd/pm: keep the BACO feature enabled for suspend
+    - Linux 5.15.14
+
+  * alsa/sdw: add sdw audio machine driver for several ADL machines
+    (LP: #1951563)
+    - ASoC: Intel: sof_sdw: Add support for SKU 0AF3 product
+    - ASoC: Intel: soc-acpi: add SKU 0AF3 SoundWire configuration
+    - ASoC: Intel: sof_sdw: Add support for SKU 0B00 and 0B01 products
+    - ASoC: Intel: sof_sdw: Add support for SKU 0B11 product
+    - ASoC: Intel: sof_sdw: Add support for SKU 0B13 product
+    - ASoC: Intel: soc-acpi: add SKU 0B13 SoundWire configuration
+    - ASoC: Intel: sof_sdw: Add support for SKU 0B29 product
+    - ASoC: Intel: soc-acpi: add SKU 0B29 SoundWire configuration
+    - ASoC: Intel: sof_sdw: Add support for SKU 0B12 product
+    - ASoC: intel: sof_sdw: return the original error number
+    - ASoC: intel: sof_sdw: rename be_index/link_id to link_index
+    - ASoC: intel: sof_sdw: Use a fixed DAI link id for AMP
+    - ASoC: intel: sof_sdw: move DMIC link id overwrite to create_sdw_dailink
+    - ASoC: intel: sof_sdw: remove SOF_RT715_DAI_ID_FIX quirk
+    - ASoC: intel: sof_sdw: remove sof_sdw_mic_codec_mockup_init
+    - ASoC: intel: sof_sdw: remove get_next_be_id
+    - ASoC: intel: sof_sdw: add link adr order check
+
+  * Add basic Wifi support for Qualcomm WCN6856 (LP: #1955613)
+    - ath11k: change to use dynamic memory for channel list of scan
+    - ath11k: add string type to search board data in board-2.bin for WCN6855
+
+  * Enable audio mute LED and mic mute LED on a new HP laptop (LP: #1956454)
+    - ALSA: hda/realtek: Use ALC285_FIXUP_HP_GPIO_LED on another HP laptop
+
+  * Add missing BT ID for Qualcomm WCN6856 (LP: #1956407)
+    - Bluetooth: btusb: Add one more Bluetooth part for WCN6855
+
+  * Add Bluetooth support for Qualcomm WCN6856 (LP: #1955689)
+    - Bluetooth: btusb: Add support using different nvm for variant WCN6855
+      controller
+    - Bluetooth: btusb: re-definition for board_id in struct qca_version
+    - Bluetooth: btusb: Add the new support IDs for WCN6855
+
+  * Improve performance and idle power consumption (LP: #1941893)
+    - x86: ACPI: cstate: Optimize C3 entry on AMD CPUs
+
+  * [Yellow Carp] USB4 interdomain communication problems (LP: #1945361)
+    - thunderbolt: Enable retry logic for intra-domain control packets
+
+  * 1951111:
+    - scsi: lpfc: Fix mailbox command failure during driver initialization
+
+  * [Jammy] Update Broadcom Emulex FC HBA lpfc driver to 14.0.0.3 for Ubuntu
+    22.04 (LP: #1951111)
+    - scsi: lpfc: Fix premature rpi release for unsolicited TPLS and LS_RJT
+    - scsi: lpfc: Fix hang on unload due to stuck fport node
+    - scsi: lpfc: Fix rediscovery of tape device after LIP
+    - scsi: lpfc: Don't remove ndlp on PRLI errors in P2P mode
+    - scsi: lpfc: Fix EEH support for NVMe I/O
+    - scsi: lpfc: Adjust bytes received vales during cmf timer interval
+    - scsi: lpfc: Fix I/O block after enabling managed congestion mode
+    - scsi: lpfc: Zero CGN stats only during initial driver load and stat reset
+    - scsi: lpfc: Improve PBDE checks during SGL processing
+    - scsi: lpfc: Update lpfc version to 14.0.0.2
+
+  * smartpqi: Update 20.04.4 to latest kernel.org patch level (LP: #1953689)
+    - scsi: smartpqi: Update device removal management
+    - scsi: smartpqi: Capture controller reason codes
+    - scsi: smartpqi: Update LUN reset handler
+    - scsi: smartpqi: Add TEST UNIT READY check for SANITIZE operation
+    - scsi: smartpqi: Avoid failing I/Os for offline devices
+    - scsi: smartpqi: Add extended report physical LUNs
+    - scsi: smartpqi: Fix boot failure during LUN rebuild
+    - scsi: smartpqi: Fix duplicate device nodes for tape changers
+    - scsi: smartpqi: Add 3252-8i PCI id
+    - scsi: smartpqi: Update version to 2.1.12-055
+
+  * Let VMD follow host bridge PCIe settings (LP: #1954611)
+    - PCI: vmd: Honor ACPI _OSC on PCIe features
+
+  * Fix spurious wakeup caused by Intel 7560 WWAN (LP: #1956443)
+    - net: wwan: iosm: Keep device at D0 for s2idle case
+
+  * [uacc-0623] hisi_sec2  fail to alloc uacce (LP: #1933301)
+    - crypto: hisilicon/qm - modify the uacce mode check
+
+  * Jammy update: v5.15.13 upstream stable release (LP: #1956926)
+    - Input: i8042 - add deferred probe support
+    - Input: i8042 - enable deferred probe quirk for ASUS UM325UA
+    - tomoyo: Check exceeded quota early in tomoyo_domain_quota_is_ok().
+    - tomoyo: use hwight16() in tomoyo_domain_quota_is_ok()
+    - net/sched: Extend qdisc control block with tc control block
+    - parisc: Clear stale IIR value on instruction access rights trap
+    - platform/mellanox: mlxbf-pmc: Fix an IS_ERR() vs NULL bug in
+      mlxbf_pmc_map_counters
+    - platform/x86: apple-gmux: use resource_size() with res
+    - memblock: fix memblock_phys_alloc() section mismatch error
+    - recordmcount.pl: fix typo in s390 mcount regex
+    - powerpc/ptdump: Fix DEBUG_WX since generic ptdump conversion
+    - efi: Move efifb_setup_from_dmi() prototype from arch headers
+    - selinux: initialize proto variable in selinux_ip_postroute_compat()
+    - scsi: lpfc: Terminate string in lpfc_debugfs_nvmeio_trc_write()
+    - net/mlx5: DR, Fix NULL vs IS_ERR checking in dr_domain_init_resources
+    - net/mlx5: Fix error print in case of IRQ request failed
+    - net/mlx5: Fix SF health recovery flow
+    - net/mlx5: Fix tc max supported prio for nic mode
+    - net/mlx5e: Wrap the tx reporter dump callback to extract the sq
+    - net/mlx5e: Fix interoperability between XSK and ICOSQ recovery flow
+    - net/mlx5e: Fix ICOSQ recovery flow for XSK
+    - net/mlx5e: Use tc sample stubs instead of ifdefs in source file
+    - net/mlx5e: Delete forward rule for ct or sample action
+    - udp: using datalen to cap ipv6 udp max gso segments
+    - selftests: Calculate udpgso segment count without header adjustment
+    - sctp: use call_rcu to free endpoint
+    - net/smc: fix using of uninitialized completions
+    - net: usb: pegasus: Do not drop long Ethernet frames
+    - net: ag71xx: Fix a potential double free in error handling paths
+    - net: lantiq_xrx200: fix statistics of received bytes
+    - NFC: st21nfca: Fix memory leak in device probe and remove
+    - net/smc: don't send CDC/LLC message if link not ready
+    - net/smc: fix kernel panic caused by race of smc_sock
+    - igc: Do not enable crosstimestamping for i225-V models
+    - igc: Fix TX timestamp support for non-MSI-X platforms
+    - drm/amd/display: Send s0i2_rdy in stream_count == 0 optimization
+    - drm/amd/display: Set optimize_pwr_state for DCN31
+    - ionic: Initialize the 'lif->dbid_inuse' bitmap
+    - net/mlx5e: Fix wrong features assignment in case of error
+    - net: bridge: mcast: add and enforce query interval minimum
+    - net: bridge: mcast: add and enforce startup query interval minimum
+    - selftests/net: udpgso_bench_tx: fix dst ip argument
+    - selftests: net: Fix a typo in udpgro_fwd.sh
+    - net: bridge: mcast: fix br_multicast_ctx_vlan_global_disabled helper
+    - net/ncsi: check for error return from call to nla_put_u32
+    - selftests: net: using ping6 for IPv6 in udpgro_fwd.sh
+    - fsl/fman: Fix missing put_device() call in fman_port_probe
+    - i2c: validate user data in compat ioctl
+    - nfc: uapi: use kernel size_t to fix user-space builds
+    - uapi: fix linux/nfc.h userspace compilation errors
+    - drm/nouveau: wait for the exclusive fence after the shared ones v2
+    - drm/amdgpu: When the VCN(1.0) block is suspended, powergating is explicitly
+      enabled
+    - drm/amdgpu: add support for IP discovery gc_info table v2
+    - drm/amd/display: Changed pipe split policy to allow for multi-display pipe
+      split
+    - xhci: Fresco FL1100 controller should not have BROKEN_MSI quirk set.
+    - usb: gadget: f_fs: Clear ffs_eventfd in ffs_data_clear.
+    - usb: mtu3: add memory barrier before set GPD's HWO
+    - usb: mtu3: fix list_head check warning
+    - usb: mtu3: set interval of FS intr and isoc endpoint
+    - nitro_enclaves: Use get_user_pages_unlocked() call to handle mmap assert
+    - binder: fix async_free_space accounting for empty parcels
+    - scsi: vmw_pvscsi: Set residual data length conditionally
+    - Input: appletouch - initialize work before device registration
+    - Input: spaceball - fix parsing of movement data packets
+    - mm/damon/dbgfs: fix 'struct pid' leaks in 'dbgfs_target_ids_write()'
+    - net: fix use-after-free in tw_timer_handler
+    - fs/mount_setattr: always cleanup mount_kattr
+    - perf intel-pt: Fix parsing of VM time correlation arguments
+    - perf script: Fix CPU filtering of a script's switch events
+    - perf scripts python: intel-pt-events.py: Fix printing of switch events
+    - Linux 5.15.13
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] getabis: Add fwinfo.builtin to the ABI
+    - [Packaging] Add list of built-in firmwares to the ABI
+    - [Config] x86-64: SYSFB_SIMPLEFB=y
+    - [packaging] arm64: introduce the lowlatency and lowlatency-64k flavours
+    - [packaging] arm64: updateconfigs
+    - [Config] annotations: remove duplicates when arm64-generic ==
+      arm64-generic-64k option
+    - [Config] annotations: introduce arm64-lowlatency and arm64-lowlatency-64k
+      kconfig options checks
+    - [Packaging] Update dependency of pahole / dwarves
+    - [Config] toolchain version update
+
+  * Miscellaneous upstream changes
+    - scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to
+      driver_resource_setup()
+    - scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
+    - scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
+    - scsi: lpfc: Update lpfc version to 14.0.0.3
+    - Revert "rtw88: Disable PCIe ASPM while doing NAPI poll on 8821CE"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Fri, 28 Jan 2022 17:16:21 +0100
+
+linux (5.15.0-18.18) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-18.18 -proposed tracker (LP: #1958638)
+
+  * CVE-2021-4155
+    - xfs: map unwritten blocks in XFS_IOC_{ALLOC, FREE}SP just like fallocate
+
+  * CVE-2022-0185
+    - SAUCE: vfs: test that one given mount param is not larger than PAGE_SIZE
+
+  * [UBUNTU 20.04] KVM hardware diagnose data improvements for guest kernel -
+    kernel part (LP: #1953334)
+    - KVM: s390: add debug statement for diag 318 CPNC data
+
+  * OOB write on BPF_RINGBUF (LP: #1956585)
+    - SAUCE: bpf: prevent helper argument PTR_TO_ALLOC_MEM to have offset other
+      than 0
+
+  * Miscellaneous Ubuntu changes
+    - [Config] re-enable shiftfs
+    - [SAUCE] shiftfs: support kernel 5.15
+    - [Config] update toolchain versions
+
+  * Miscellaneous upstream changes
+    - vfs: fs_context: fix up param length parsing in legacy_parse_param
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Fri, 21 Jan 2022 13:32:27 +0100
+
+linux (5.15.0-17.17) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-17.17 -proposed tracker (LP: #1957809)
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 13 Jan 2022 17:11:21 +0100
+
+linux (5.15.0-16.16) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-16.16 -proposed tracker (LP: #1956820)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * 5.15 stuck at boot on c4.large (LP: #1956780)
+    - Revert "PCI/MSI: Mask MSI-X vectors only on success"
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Packaging] temporarily disable signed v4l2loopback"
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Sat, 08 Jan 2022 10:57:58 +0100
+
+linux (5.15.0-15.15) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-15.15 -proposed tracker (LP: #1956314)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * rtw88_8821ce causes freeze (LP: #1927808)
+    - rtw88: Disable PCIe ASPM while doing NAPI poll on 8821CE
+
+  * alsa/sdw: fix the  audio sdw codec parsing logic in the acpi table
+    (LP: #1955686)
+    - ALSA: hda: intel-sdw-acpi: go through HDAS ACPI at max depth of 2
+    - ALSA: hda: intel-sdw-acpi: harden detection of controller
+
+  * Got black screen when resume from s2idle with AMD dGPU (LP: #1955790)
+    - SAUCE: drm/amdgpu: put SMU into proper state on runpm suspending for BOCO
+      capable platform
+    - SAUCE: drm/amdgpu: always reset the asic in suspend (v2)
+
+  *  Fix USB3 detection on HP dock (LP: #1955443)
+    - usb: hub: Add delay for SuperSpeed hub resume to let links transit to U0
+
+  * support signed v4l2loopback dkms build (LP: #1938531)
+    - enable v4l2loopback builds on amd64 kernels
+    - support v4l2loopback dkms build
+
+  * Jammy update: v5.15.12 upstream stable release (LP: #1956305)
+    - arm64: vdso32: require CROSS_COMPILE_COMPAT for gcc+bfd
+    - net: usb: lan78xx: add Allied Telesis AT29M2-AF
+    - ext4: prevent partial update of the extent blocks
+    - ext4: check for out-of-order index extents in ext4_valid_extent_entries()
+    - ext4: check for inconsistent extents between index and leaf block
+    - selftests: KVM: Fix non-x86 compiling
+    - HID: holtek: fix mouse probing
+    - HID: potential dereference of null pointer
+    - NFSD: Fix READDIR buffer overflow
+    - PM: sleep: Fix error handling in dpm_prepare()
+    - arm64: dts: allwinner: orangepi-zero-plus: fix PHY mode
+    - bus: sunxi-rsb: Fix shutdown
+    - spi: change clk_disable_unprepare to clk_unprepare
+    - ucounts: Fix rlimit max values check
+    - drm/mediatek: hdmi: Perform NULL pointer check for mtk_hdmi_conf
+    - ASoC: meson: aiu: fifo: Add missing dma_coerce_mask_and_coherent()
+    - RDMA/hns: Fix RNR retransmission issue for HIP08
+    - IB/qib: Fix memory leak in qib_user_sdma_queue_pkts()
+    - RDMA/hns: Replace kfree() with kvfree()
+    - netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy()
+    - netfilter: fix regression in looped (broad|multi)cast's MAC handling
+    - ARM: dts: imx6qdl-wandboard: Fix Ethernet support
+    - ice: Use xdp_buf instead of rx_buf for xsk zero-copy
+    - ice: xsk: return xsk buffers back to pool when cleaning the ring
+    - net: marvell: prestera: fix incorrect return of port_find
+    - net: marvell: prestera: fix incorrect structure access
+    - qlcnic: potential dereference null pointer of rx_queue->page_ring
+    - tcp: move inet->rx_dst_ifindex to sk->sk_rx_dst_ifindex
+    - ipv6: move inet6_sk(sk)->rx_dst_cookie to sk->sk_rx_dst_cookie
+    - inet: fully convert sk->sk_rx_dst to RCU rules
+    - net: accept UFOv6 packages in virtio_net_hdr_to_skb
+    - net: skip virtio_net_hdr_set_proto if protocol already set
+    - igb: fix deadlock caused by taking RTNL in RPM resume path
+    - ipmi: Fix UAF when uninstall ipmi_si and ipmi_msghandler module
+    - gpio: virtio: remove timeout
+    - bonding: fix ad_actor_system option setting to default
+    - fjes: Check for error irq
+    - drivers: net: smc911x: Check for error irq
+    - net: ks8851: Check for error irq
+    - sfc: Check null pointer of rx_queue->page_ring
+    - sfc: falcon: Check null pointer of rx_queue->page_ring
+    - asix: fix uninit-value in asix_mdio_read()
+    - asix: fix wrong return value in asix_check_host_enable()
+    - io_uring: zero iocb->ki_pos for stream file types
+    - veth: ensure skb entering GRO are not cloned.
+    - net: stmmac: ptp: fix potentially overflowing expression
+    - net: bridge: Use array_size() helper in copy_to_user()
+    - net: bridge: fix ioctl old_deviceless bridge argument
+    - r8152: fix the force speed doesn't work for RTL8156
+    - net: stmmac: dwmac-visconti: Fix value of ETHER_CLK_SEL_FREQ_SEL_2P5M
+    - pinctrl: bcm2835: Change init order for gpio hogs
+    - hwmon: (lm90) Fix usage of CONFIG2 register in detect function
+    - hwmon: (lm90) Prevent integer overflow/underflow in hysteresis calculations
+    - hwmon: (lm90) Introduce flag indicating extended temperature support
+    - hwmon: (lm90) Add basic support for TI TMP461
+    - hwmon: (lm90) Drop critical attribute support for MAX6654
+    - ARM: 9160/1: NOMMU: Reload __secondary_data after PROCINFO_INITFUNC
+    - uapi: Fix undefined __always_inline on non-glibc systems
+    - compiler.h: Fix annotation macro misplacement with Clang
+    - platform/x86/intel: Remove X86_PLATFORM_DRIVERS_INTEL
+    - kernel/crash_core: suppress unknown crashkernel parameter warning
+    - Revert "x86/boot: Pull up cmdline preparation and early param parsing"
+    - x86/boot: Move EFI range reservation after cmdline parsing
+    - ALSA: jack: Check the return value of kstrdup()
+    - ALSA: drivers: opl3: Fix incorrect use of vp->state
+    - ALSA: rawmidi - fix the uninitalized user_pversion
+    - ALSA: hda/hdmi: Disable silent stream on GLK
+    - ALSA: hda/realtek: Amp init fixup for HP ZBook 15 G6
+    - ALSA: hda/realtek: Add new alc285-hp-amp-init model
+    - ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
+    - ALSA: hda/realtek: Fix quirk for Clevo NJ51CU
+    - ASoC: meson: aiu: Move AIU_I2S_MISC hold setting to aiu-fifo-i2s
+    - ASoC: tegra: Add DAPM switches for headphones and mic jack
+    - ASoC: tegra: Restore headphones jack name on Nyan Big
+    - Input: atmel_mxt_ts - fix double free in mxt_read_info_block
+    - ipmi: bail out if init_srcu_struct fails
+    - ipmi: ssif: initialize ssif_info->client early
+    - ipmi: fix initialization when workqueue allocation fails
+    - parisc: Correct completer in lws start
+    - parisc: Fix mask used to select futex spinlock
+    - tee: handle lookup of shm with reference count 0
+    - x86/pkey: Fix undefined behaviour with PKRU_WD_BIT
+    - platform/x86: amd-pmc: only use callbacks for suspend
+    - platform/x86: intel_pmc_core: fix memleak on registration failure
+    - KVM: x86: Always set kvm_run->if_flag
+    - KVM: x86/mmu: Don't advance iterator after restart due to yielding
+    - KVM: nVMX: Synthesize TRIPLE_FAULT for L2 if emulation is required
+    - KVM: VMX: Always clear vmx->fail on emulation_required
+    - KVM: VMX: Wake vCPU when delivering posted IRQ even if vCPU == this vCPU
+    - pinctrl: stm32: consider the GPIO offset to expose all the GPIO lines
+    - gpio: dln2: Fix interrupts when replugging the device
+    - mmc: sdhci-tegra: Fix switch to HS400ES mode
+    - mmc: meson-mx-sdhc: Set MANUAL_STOP for multi-block SDIO commands
+    - mmc: core: Disable card detect during shutdown
+    - mmc: mmci: stm32: clear DLYB_CR after sending tuning command
+    - ARM: 9169/1: entry: fix Thumb2 bug in iWMMXt exception handling
+    - ksmbd: fix error code in ndr_read_int32()
+    - ksmbd: fix uninitialized symbol 'pntsd_size'
+    - ksmbd: disable SMB2_GLOBAL_CAP_ENCRYPTION for SMB 3.1.1
+    - mac80211: fix locking in ieee80211_start_ap error path
+    - mm: mempolicy: fix THP allocations escaping mempolicy restrictions
+    - mm, hwpoison: fix condition in free hugetlb page path
+    - mm/hwpoison: clear MF_COUNT_INCREASED before retrying get_any_page()
+    - mm/damon/dbgfs: protect targets destructions with kdamond_lock
+    - tee: optee: Fix incorrect page free bug
+    - f2fs: fix to do sanity check on last xattr entry in __f2fs_setxattr()
+    - netfs: fix parameter of cleanup()
+    - KVM: VMX: Fix stale docs for kvm-intel.emulate_invalid_guest_state
+    - arm64: dts: lx2160a: fix scl-gpios property name
+    - kfence: fix memory leak when cat kfence objects
+    - Input: iqs626a - prohibit inlining of channel parsing functions
+    - Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
+    - Input: goodix - add id->model mapping for the "9111" model
+    - ASoC: tas2770: Fix setting of high sample rates
+    - ASoC: SOF: Intel: pci-tgl: add new ADL-P variant
+    - ASoC: SOF: Intel: pci-tgl: add ADL-N support
+    - ASoC: rt5682: fix the wrong jack type detected
+    - pinctrl: mediatek: fix global-out-of-bounds issue
+    - hwmom: (lm90) Fix citical alarm status for MAX6680/MAX6681
+    - hwmon: (lm90) Do not report 'busy' status bit as alarm
+    - r8152: sync ocp base
+    - ax25: NPD bug when detaching AX25 device
+    - hamradio: defer ax25 kfree after unregister_netdev
+    - hamradio: improve the incomplete fix to avoid NPD
+    - tun: avoid double free in tun_free_netdev
+    - phonet/pep: refuse to enable an unbound pipe
+    - Linux 5.15.12
+
+  * Thinkpad E14 Gen2: Kernel panic with trackpad and trackpoint enabled
+    (LP: #1945590) // Jammy update: v5.15.12 upstream stable release
+    (LP: #1956305)
+    - Input: elantech - fix stack out of bound access in
+      elantech_change_report_id()
+
+  * Jammy update: v5.15.11 upstream stable release (LP: #1956302)
+    - reset: tegra-bpmp: Revert Handle errors in BPMP response
+    - KVM: VMX: clear vmx_x86_ops.sync_pir_to_irr if APICv is disabled
+    - KVM: selftests: Make sure kvm_create_max_vcpus test won't hit RLIMIT_NOFILE
+    - KVM: downgrade two BUG_ONs to WARN_ON_ONCE
+    - x86/kvm: remove unused ack_notifier callbacks
+    - KVM: X86: Fix tlb flush for tdp in kvm_invalidate_pcid()
+    - mac80211: fix rate control for retransmitted frames
+    - mac80211: fix regression in SSN handling of addba tx
+    - mac80211: mark TX-during-stop for TX in in_reconfig
+    - mac80211: send ADDBA requests using the tid/queue of the aggregation session
+    - mac80211: validate extended element ID is present
+    - firmware: arm_scpi: Fix string overflow in SCPI genpd driver
+    - bpf: Fix kernel address leakage in atomic fetch
+    - bpf, selftests: Add test case for atomic fetch on spilled pointer
+    - bpf: Fix signed bounds propagation after mov32
+    - bpf: Make 32->64 bounds propagation slightly more robust
+    - bpf, selftests: Add test case trying to taint map value pointer
+    - bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux reg
+    - bpf, selftests: Update test case for atomic cmpxchg on r0 with pointer
+    - vduse: fix memory corruption in vduse_dev_ioctl()
+    - vduse: check that offset is within bounds in get_config()
+    - virtio_ring: Fix querying of maximum DMA mapping size for virtio device
+    - vdpa: check that offsets are within bounds
+    - s390/entry: fix duplicate tracking of irq nesting level
+    - recordmcount.pl: look for jgnop instruction as well as bcrl on s390
+    - arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys
+    - ceph: fix up non-directory creation in SGID directories
+    - dm btree remove: fix use after free in rebalance_children()
+    - audit: improve robustness of the audit queue handling
+    - btrfs: convert latest_bdev type to btrfs_device and rename
+    - btrfs: use latest_dev in btrfs_show_devname
+    - btrfs: update latest_dev when we create a sprout device
+    - btrfs: remove stale comment about the btrfs_show_devname
+    - scsi: ufs: core: Retry START_STOP on UNIT_ATTENTION
+    - arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-
+      edge
+    - arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply
+    - arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply
+    - arm64: dts: rockchip: fix audio-supply for Rock Pi 4
+    - arm64: dts: rockchip: fix poweroff on helios64
+    - dmaengine: idxd: add halt interrupt support
+    - dmaengine: idxd: fix calling wq quiesce inside spinlock
+    - mac80211: track only QoS data frames for admission control
+    - tee: amdtee: fix an IS_ERR() vs NULL bug
+    - ceph: fix duplicate increment of opened_inodes metric
+    - ceph: initialize pathlen variable in reconnect_caps_cb
+    - ARM: socfpga: dts: fix qspi node compatible
+    - arm64: dts: imx8mq: remove interconnect property from lcdif
+    - clk: Don't parent clks until the parent is fully registered
+    - soc: imx: Register SoC device only on i.MX boards
+    - iwlwifi: mvm: don't crash on invalid rate w/o STA
+    - virtio: always enter drivers/virtio/
+    - virtio/vsock: fix the transport to work with VMADDR_CID_ANY
+    - vdpa: Consider device id larger than 31
+    - Revert "drm/fb-helper: improve DRM fbdev emulation device names"
+    - selftests: net: Correct ping6 expected rc from 2 to 1
+    - s390/kexec_file: fix error handling when applying relocations
+    - sch_cake: do not call cake_destroy() from cake_init()
+    - inet_diag: fix kernel-infoleak for UDP sockets
+    - netdevsim: don't overwrite read only ethtool parms
+    - selftests: icmp_redirect: pass xfail=0 to log_test()
+    - net: hns3: fix use-after-free bug in hclgevf_send_mbx_msg
+    - net: hns3: fix race condition in debugfs
+    - selftests: Add duplicate config only for MD5 VRF tests
+    - selftests: Fix raw socket bind tests with VRF
+    - selftests: Fix IPv6 address bind tests
+    - dmaengine: idxd: fix missed completion on abort path
+    - dmaengine: st_fdma: fix MODULE_ALIAS
+    - drm: simpledrm: fix wrong unit with pixel clock
+    - net/sched: sch_ets: don't remove idle classes from the round-robin list
+    - selftests/net: toeplitz: fix udp option
+    - net: dsa: mv88e6xxx: Unforce speed & duplex in mac_link_down()
+    - selftest/net/forwarding: declare NETIFS p9 p10
+    - mptcp: never allow the PM to close a listener subflow
+    - drm/ast: potential dereference of null pointer
+    - drm/i915/display: Fix an unsigned subtraction which can never be negative.
+    - mac80211: agg-tx: don't schedule_and_wake_txq() under sta->lock
+    - cfg80211: Acquire wiphy mutex on regulatory work
+    - mac80211: fix lookup when adding AddBA extension element
+    - net: stmmac: fix tc flower deletion for VLAN priority Rx steering
+    - flow_offload: return EOPNOTSUPP for the unsupported mpls action type
+    - rds: memory leak in __rds_conn_create()
+    - ice: Use div64_u64 instead of div_u64 in adjfine
+    - ice: Don't put stale timestamps in the skb
+    - drm/amd/display: Set exit_optimized_pwr_state for DCN31
+    - drm/amd/pm: fix a potential gpu_metrics_table memory leak
+    - mptcp: remove tcp ulp setsockopt support
+    - mptcp: clear 'kern' flag from fallback sockets
+    - mptcp: fix deadlock in __mptcp_push_pending()
+    - soc/tegra: fuse: Fix bitwise vs. logical OR warning
+    - igb: Fix removal of unicast MAC filters of VFs
+    - igbvf: fix double free in `igbvf_probe`
+    - igc: Fix typo in i225 LTR functions
+    - ixgbe: Document how to enable NBASE-T support
+    - ixgbe: set X550 MDIO speed before talking to PHY
+    - netdevsim: Zero-initialize memory for new map's value in function
+      nsim_bpf_map_alloc
+    - net/packet: rx_owner_map depends on pg_vec
+    - net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
+    - sfc_ef100: potential dereference of null pointer
+    - dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
+    - net: Fix double 0x prefix print in SKB dump
+    - net/smc: Prevent smc_release() from long blocking
+    - net: systemport: Add global locking for descriptor lifecycle
+    - sit: do not call ipip6_dev_free() from sit_init_net()
+    - afs: Fix mmap
+    - arm64: kexec: Fix missing error code 'ret' warning in load_other_segments()
+    - bpf: Fix extable fixup offset.
+    - bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
+    - powerpc/85xx: Fix oops when CONFIG_FSL_PMC=n
+    - USB: gadget: bRequestType is a bitfield, not a enum
+    - Revert "usb: early: convert to readl_poll_timeout_atomic()"
+    - KVM: x86: Drop guest CPUID check for host initiated writes to
+      MSR_IA32_PERF_CAPABILITIES
+    - tty: n_hdlc: make n_hdlc_tty_wakeup() asynchronous
+    - USB: NO_LPM quirk Lenovo USB-C to Ethernet Adapher(RTL8153-04)
+    - usb: dwc2: fix STM ID/VBUS detection startup delay in dwc2_driver_probe
+    - PCI/MSI: Clear PCI_MSIX_FLAGS_MASKALL on error
+    - PCI/MSI: Mask MSI-X vectors only on success
+    - usb: xhci-mtk: fix list_del warning when enable list debug
+    - usb: xhci: Extend support for runtime power management for AMD's Yellow
+      carp.
+    - usb: cdnsp: Fix incorrect status for control request
+    - usb: cdnsp: Fix incorrect calling of cdnsp_died function
+    - usb: cdnsp: Fix issue in cdnsp_log_ep trace event
+    - usb: cdnsp: Fix lack of spin_lock_irqsave/spin_lock_restore
+    - usb: typec: tcpm: fix tcpm unregister port but leave a pending timer
+    - usb: gadget: u_ether: fix race in setting MAC address in setup phase
+    - USB: serial: cp210x: fix CP2105 GPIO registration
+    - USB: serial: option: add Telit FN990 compositions
+    - selinux: fix sleeping function called from invalid context
+    - btrfs: fix memory leak in __add_inode_ref()
+    - btrfs: fix double free of anon_dev after failure to create subvolume
+    - btrfs: check WRITE_ERR when trying to read an extent buffer
+    - btrfs: fix missing blkdev_put() call in btrfs_scan_one_device()
+    - zonefs: add MODULE_ALIAS_FS
+    - iocost: Fix divide-by-zero on donation from low hweight cgroup
+    - serial: 8250_fintek: Fix garbled text for console
+    - timekeeping: Really make sure wall_to_monotonic isn't positive
+    - cifs: sanitize multiple delimiters in prepath
+    - locking/rtmutex: Fix incorrect condition in rtmutex_spin_on_owner()
+    - riscv: dts: unleashed: Add gpio card detect to mmc-spi-slot
+    - riscv: dts: unmatched: Add gpio card detect to mmc-spi-slot
+    - perf inject: Fix segfault due to close without open
+    - perf inject: Fix segfault due to perf_data__fd() without open
+    - libata: if T_LENGTH is zero, dma direction should be DMA_NONE
+    - powerpc/module_64: Fix livepatching for RO modules
+    - drm/amdgpu: correct register access for RLC_JUMP_TABLE_RESTORE
+    - drm/amdgpu: don't override default ECO_BITs setting
+    - drm/amd/pm: fix reading SMU FW version from amdgpu_firmware_info on YC
+    - Revert "can: m_can: remove support for custom bit timing"
+    - can: m_can: make custom bittiming fields const
+    - can: m_can: pci: use custom bit timings for Elkhart Lake
+    - ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name
+    - xsk: Do not sleep in poll() when need_wakeup set
+    - mptcp: add missing documented NL params
+    - bpf, x64: Factor out emission of REX byte in more cases
+    - bpf: Fix extable address check.
+    - USB: core: Make do_proc_control() and do_proc_bulk() killable
+    - media: mxl111sf: change mutex_init() location
+    - fuse: annotate lock in fuse_reverse_inval_entry()
+    - ovl: fix warning in ovl_create_real()
+    - scsi: scsi_debug: Don't call kcalloc() if size arg is zero
+    - scsi: scsi_debug: Fix type in min_t to avoid stack OOB
+    - scsi: scsi_debug: Sanity check block descriptor length in resp_mode_select()
+    - io-wq: remove spurious bit clear on task_work addition
+    - io-wq: check for wq exit after adding new worker task_work
+    - rcu: Mark accesses to rcu_state.n_force_qs
+    - io-wq: drop wqe lock before creating new worker
+    - bus: ti-sysc: Fix variable set but not used warning for reinit_modules
+    - selftests/damon: test debugfs file reads/writes with huge count
+    - Revert "xsk: Do not sleep in poll() when need_wakeup set"
+    - xen/blkfront: harden blkfront against event channel storms
+    - xen/netfront: harden netfront against event channel storms
+    - xen/console: harden hvc_xen against event channel storms
+    - xen/netback: fix rx queue stall detection
+    - xen/netback: don't queue unlimited number of packages
+    - Linux 5.15.11
+
+  * Jammy update: v5.15.10 upstream stable release (LP: #1956301)
+    - nfc: fix segfault in nfc_genl_dump_devices_done
+    - hwmon: (corsair-psu) fix plain integer used as NULL pointer
+    - RDMA: Fix use-after-free in rxe_queue_cleanup
+    - RDMA/mlx5: Fix releasing unallocated memory in dereg MR flow
+    - mtd: rawnand: Fix nand_erase_op delay
+    - mtd: rawnand: Fix nand_choose_best_timings() on unsupported interface
+    - inet: use #ifdef CONFIG_SOCK_RX_QUEUE_MAPPING consistently
+    - dt-bindings: media: nxp,imx7-mipi-csi2: Drop bad if/then schema
+    - clk: qcom: sm6125-gcc: Swap ops of ice and apps on sdcc1
+    - perf bpf_skel: Do not use typedef to avoid error on old clang
+    - netfs: Fix lockdep warning from taking sb_writers whilst holding mmap_lock
+    - RDMA/irdma: Fix a user-after-free in add_pble_prm
+    - RDMA/irdma: Fix a potential memory allocation issue in
+      'irdma_prm_add_pble_mem()'
+    - RDMA/irdma: Report correct WC errors
+    - RDMA/irdma: Don't arm the CQ more than two times if no CE for this CQ
+    - ice: fix FDIR init missing when reset VF
+    - vmxnet3: fix minimum vectors alloc issue
+    - i2c: virtio: fix completion handling
+    - drm/msm: Fix null ptr access msm_ioctl_gem_submit()
+    - drm/msm/a6xx: Fix uinitialized use of gpu_scid
+    - drm/msm/dsi: set default num_data_lanes
+    - drm/msm/dp: Avoid unpowered AUX xfers that caused crashes
+    - KVM: arm64: Save PSTATE early on exit
+    - s390/test_unwind: use raw opcode instead of invalid instruction
+    - Revert "tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"
+    - net/mlx4_en: Update reported link modes for 1/10G
+    - loop: Use pr_warn_once() for loop_control_remove() warning
+    - ALSA: hda: Add Intel DG2 PCI ID and HDMI codec vid
+    - ALSA: hda/hdmi: fix HDA codec entry table order for ADL-P
+    - parisc/agp: Annotate parisc agp init functions with __init
+    - i2c: rk3x: Handle a spurious start completion interrupt flag
+    - net: netlink: af_netlink: Prevent empty skb by adding a check on len.
+    - drm/amdgpu: cancel the correct hrtimer on exit
+    - drm/amdgpu: check atomic flag to differeniate with legacy path
+    - drm/amd/display: Fix for the no Audio bug with Tiled Displays
+    - drm/amdkfd: fix double free mem structure
+    - drm/amd/display: add connector type check for CRC source set
+    - drm/amdkfd: process_info lock not needed for svm
+    - tracing: Fix a kmemleak false positive in tracing_map
+    - staging: most: dim2: use device release method
+    - fuse: make sure reclaim doesn't write the inode
+    - perf inject: Fix itrace space allowed for new attributes
+    - Linux 5.15.10
+
+  * Jammy update: v5.15.9 upstream stable release (LP: #1955161)
+    - netfilter: selftest: conntrack_vrf.sh: fix file permission
+    - Linux 5.15.9
+
+  * [SRU][I/J/OEM-5.13/OEM-5.14] Fix pci port lost when hotplug dock
+    (LP: #1954646)
+    - PCI: Re-enable Downstream Port LTR after reset or hotplug
+
+  * Add support for NVIDIA EC backlight (LP: #1953286)
+    - platform/x86: Add driver for ACPI WMAA EC-based backlight control
+    - platform/x86: Remove "WMAA" from identifier names in wmaa-backlight-wmi.c
+    - platform/x86: Rename wmaa-backlight-wmi to nvidia-wmi-ec-backlight
+    - [Config] NVIDIA_WMI_EC_BACKLIGHT=m
+
+  * Improve USB Type-C support (LP: #1950974)
+    - usb: typec: ucsi: Always cancel the command if PPM reports BUSY condition
+    - usb: typec: ucsi: Don't stop alt mode registration on busy condition
+    - usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode
+      checking
+    - usb: typec: ucsi: acpi: Reduce the command completion timeout
+    - usb: typec: ucsi: Check the partner alt modes always if there is PD contract
+    - usb: typec: ucsi: Read the PDOs in separate work
+    - usb: typec: ucsi: Better fix for missing unplug events issue
+
+  *  Fix power button wakeup with shared IRQs on AMD platforms (LP: #1953540)
+    - pinctrl: amd: Fix wakeups when IRQ is shared with SCI
+
+  * AMD: Suspend not working when some cores are disabled through cpufreq
+    (LP: #1954930)
+    - ACPI: processor idle: Allow playing dead in C3 state
+
+  * Jammy update: v5.15.8 upstream stable release (LP: #1954931)
+    - Revert "UBUNTU: SAUCE: selftests: fib_tests: assign address to dummy1 for
+      rp_filter tests"
+    - usb: gadget: uvc: fix multiple opens
+    - HID: quirks: Add quirk for the Microsoft Surface 3 type-cover
+    - HID: google: add eel USB id
+    - HID: intel-ish-hid: ipc: only enable IRQ wakeup when requested
+    - HID: add hid_is_usb() function to make it simpler for USB detection
+    - HID: add USB_HID dependancy to hid-prodikeys
+    - HID: add USB_HID dependancy to hid-chicony
+    - HID: add USB_HID dependancy on some USB HID drivers
+    - HID: bigbenff: prevent null pointer dereference
+    - HID: wacom: fix problems when device is not a valid USB device
+    - HID: check for valid USB device for many HID drivers
+    - mtd: dataflash: Add device-tree SPI IDs
+    - mmc: spi: Add device-tree SPI IDs
+    - HID: sony: fix error path in probe
+    - HID: Ignore battery for Elan touchscreen on Asus UX550VE
+    - platform/x86/intel: hid: add quirk to support Surface Go 3
+    - nft_set_pipapo: Fix bucket load in AVX2 lookup routine for six 8-bit groups
+    - IB/hfi1: Insure use of smp_processor_id() is preempt disabled
+    - IB/hfi1: Fix early init panic
+    - IB/hfi1: Fix leak of rcvhdrtail_dummy_kvaddr
+    - can: kvaser_usb: get CAN clock frequency from device
+    - can: kvaser_pciefd: kvaser_pciefd_rx_error_frame(): increase correct
+      stats->{rx,tx}_errors counter
+    - can: sja1000: fix use after free in ems_pcmcia_add_card()
+    - can: pch_can: pch_can_rx_normal: fix use after free
+    - can: m_can: m_can_read_fifo: fix memory leak in error branch
+    - can: m_can: pci: fix incorrect reference clock rate
+    - can: m_can: pci: fix iomap_read_fifo() and iomap_write_fifo()
+    - can: m_can: Disable and ignore ELO interrupt
+    - net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
+    - net: dsa: mv88e6xxx: allow use of PHYs on CPU and DSA ports
+    - x86/sme: Explicitly map new EFI memmap table as encrypted
+    - platform/x86: amd-pmc: Fix s2idle failures on certain AMD laptops
+    - nfc: fix potential NULL pointer deref in nfc_genl_dump_ses_done
+    - selftests: netfilter: add a vrf+conntrack testcase
+    - vrf: don't run conntrack on vrf with !dflt qdisc
+    - bpf, x86: Fix "no previous prototype" warning
+    - bpf, sockmap: Attach map progs to psock early for feature probes
+    - bpf: Make sure bpf_disable_instrumentation() is safe vs preemption.
+    - bpf: Fix the off-by-two error in range markings
+    - ice: ignore dropped packets during init
+    - ethtool: do not perform operations on net devices being unregistered
+    - bonding: make tx_rebalance_counter an atomic
+    - nfp: Fix memory leak in nfp_cpp_area_cache_add()
+    - udp: using datalen to cap max gso segments
+    - netfilter: nft_exthdr: break evaluation if setting TCP option fails
+    - netfilter: conntrack: annotate data-races around ct->timeout
+    - iavf: restore MSI state on reset
+    - iavf: Fix reporting when setting descriptor count
+    - IB/hfi1: Correct guard on eager buffer deallocation
+    - devlink: fix netns refcount leak in devlink_nl_cmd_reload()
+    - net: bcm4908: Handle dma_set_coherent_mask error codes
+    - net: dsa: mv88e6xxx: error handling for serdes_power functions
+    - net: dsa: felix: Fix memory leak in felix_setup_mmio_filtering
+    - net/sched: fq_pie: prevent dismantle issue
+    - net: mvpp2: fix XDP rx queues registering
+    - KVM: x86: Don't WARN if userspace mucks with RCX during string I/O exit
+    - KVM: x86: Ignore sparse banks size for an "all CPUs", non-sparse IPI req
+    - KVM: x86: Wait for IPIs to be delivered when handling Hyper-V TLB flush
+      hypercall
+    - timers: implement usleep_idle_range()
+    - mm/damon/core: fix fake load reports due to uninterruptible sleeps
+    - mm/slub: fix endianness bug for alloc/free_traces attributes
+    - mm: bdi: initialize bdi_min_ratio when bdi is unregistered
+    - ALSA: ctl: Fix copy of updated id with element read/write
+    - ALSA: hda/realtek - Add headset Mic support for Lenovo ALC897 platform
+    - ALSA: hda/realtek: Fix quirk for TongFang PHxTxX1
+    - ALSA: pcm: oss: Fix negative period/buffer sizes
+    - ALSA: pcm: oss: Limit the period size to 16MB
+    - ALSA: pcm: oss: Handle missing errors in snd_pcm_oss_change_params*()
+    - cifs: Fix crash on unload of cifs_arc4.ko
+    - scsi: qla2xxx: Format log strings only if needed
+    - btrfs: clear extent buffer uptodate when we fail to write it
+    - btrfs: fix re-dirty process of tree-log nodes
+    - btrfs: replace the BUG_ON in btrfs_del_root_ref with proper error handling
+    - btrfs: free exchange changeset on failures
+    - perf intel-pt: Fix some PGE (packet generation enable/control flow packets)
+      usage
+    - perf intel-pt: Fix sync state when a PSB (synchronization) packet is found
+    - perf intel-pt: Fix intel_pt_fup_event() assumptions about setting state type
+    - perf intel-pt: Fix state setting when receiving overflow (OVF) packet
+    - perf intel-pt: Fix next 'err' value, walking trace
+    - perf intel-pt: Fix missing 'instruction' events with 'q' option
+    - perf intel-pt: Fix error timestamp setting on the decoder error path
+    - md: fix update super 1.0 on rdev size change
+    - nfsd: fix use-after-free due to delegation race
+    - nfsd: Fix nsfd startup race (again)
+    - tracefs: Have new files inherit the ownership of their parent
+    - selftests: KVM: avoid failures due to reserved HyperTransport region
+    - hwmon: (pwm-fan) Ensure the fan going on in .probe()
+    - mmc: renesas_sdhi: initialize variable properly when tuning
+    - clk: qcom: regmap-mux: fix parent clock lookup
+    - thermal: int340x: Fix VCoRefLow MMIO bit offset for TGL
+    - drm/syncobj: Deal with signalled fences in drm_syncobj_find_fence.
+    - libata: add horkage for ASMedia 1092
+    - io_uring: ensure task_work gets run as part of cancelations
+    - wait: add wake_up_pollfree()
+    - binder: use wake_up_pollfree()
+    - signalfd: use wake_up_pollfree()
+    - aio: keep poll requests on waitqueue until completed
+    - aio: fix use-after-free due to missing POLLFREE handling
+    - tracefs: Set all files to the same group ownership as the mount option
+    - i2c: mpc: Use atomic read and fix break condition
+    - block: fix ioprio_get(IOPRIO_WHO_PGRP) vs setuid(2)
+    - scsi: pm80xx: Do not call scsi_remove_host() in pm8001_alloc()
+    - scsi: scsi_debug: Fix buffer size of REPORT ZONES command
+    - ALSA: usb-audio: Reorder snd_djm_devices[] entries
+    - qede: validate non LSO skb length
+    - PM: runtime: Fix pm_runtime_active() kerneldoc comment
+    - ASoC: rt5682: Fix crash due to out of scope stack vars
+    - ASoC: qdsp6: q6routing: Fix return value from msm_routing_put_audio_mixer
+    - ASoC: codecs: wsa881x: fix return values from kcontrol put
+    - ASoC: codecs: wcd934x: handle channel mappping list correctly
+    - ASoC: codecs: wcd934x: return correct value from mixer put
+    - RDMA/hns: Do not halt commands during reset until later
+    - RDMA/hns: Do not destroy QP resources in the hw resetting phase
+    - hwmon: (dell-smm) Fix warning on /proc/i8k creation error
+    - clk: imx: use module_platform_driver
+    - clk: qcom: clk-alpha-pll: Don't reconfigure running Trion
+    - i40e: Fix failed opcode appearing if handling messages from VF
+    - i40e: Fix pre-set max number of queues for VF
+    - mtd: rawnand: fsmc: Take instruction delay into account
+    - mtd: rawnand: fsmc: Fix timing computation
+    - bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap
+    - i40e: Fix NULL pointer dereference in i40e_dbg_dump_desc
+    - Revert "PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge"
+    - drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset
+    - perf tools: Fix SMT detection fast read path
+    - Documentation/locking/locktypes: Update migrate_disable() bits.
+    - dt-bindings: net: Reintroduce PHY no lane swap binding
+    - tools build: Remove needless libpython-version feature check that breaks
+      test-all fast path
+    - net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero
+    - net: altera: set a couple error code in probe()
+    - net: fec: only clear interrupt of handling queue in fec_enet_rx_queue()
+    - net, neigh: clear whole pneigh_entry at alloc time
+    - net/qla3xxx: fix an error code in ql_adapter_up()
+    - selftests/fib_tests: Rework fib_rp_filter_test()
+    - USB: gadget: detect too-big endpoint 0 requests
+    - USB: gadget: zero allocate endpoint 0 buffers
+    - Revert "usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default"
+    - usb: core: config: fix validation of wMaxPacketValue entries
+    - usb: core: config: using bit mask instead of individual bits
+    - xhci: avoid race between disable slot command and host runtime suspend
+    - iio: gyro: adxrs290: fix data signedness
+    - iio: trigger: Fix reference counting
+    - iio: trigger: stm32-timer: fix MODULE_ALIAS
+    - iio: stk3310: Don't return error code in interrupt handler
+    - iio: mma8452: Fix trigger reference couting
+    - iio: ltr501: Don't return error code in trigger handler
+    - iio: kxsd9: Don't return error code in trigger handler
+    - iio: itg3200: Call iio_trigger_notify_done() on error
+    - iio: dln2-adc: Fix lockdep complaint
+    - iio: dln2: Check return value of devm_iio_trigger_register()
+    - iio: at91-sama5d2: Fix incorrect sign extension
+    - iio: adc: stm32: fix a current leak by resetting pcsel before disabling vdda
+    - iio: adc: axp20x_adc: fix charging current reporting on AXP22x
+    - iio: ad7768-1: Call iio_trigger_notify_done() on error
+    - iio: accel: kxcjk-1013: Fix possible memory leak in probe and remove
+    - nvmem: eeprom: at25: fix FRAM byte_len
+    - bus: mhi: pci_generic: Fix device recovery failed issue
+    - bus: mhi: core: Add support for forced PM resume
+    - csky: fix typo of fpu config macro
+    - irqchip/aspeed-scu: Replace update_bits with write_bits.
+    - irqchip/armada-370-xp: Fix return value of armada_370_xp_msi_alloc()
+    - irqchip/armada-370-xp: Fix support for Multi-MSI interrupts
+    - aio: Fix incorrect usage of eventfd_signal_allowed()
+    - irqchip/irq-gic-v3-its.c: Force synchronisation when issuing INVALL
+    - irqchip: nvic: Fix offset for Interrupt Priority Offsets
+    - misc: fastrpc: fix improper packet size calculation
+    - clocksource/drivers/dw_apb_timer_of: Fix probe failure
+    - bpf: Add selftests to cover packet access corner cases
+    - Linux 5.15.8
+
+  * Can't read/write SD card after running CPU offline test in 5.11.0 and 5.13.0
+    (LP: #1951784) // Jammy update: v5.15.8 upstream stable release
+    (LP: #1954931)
+    - misc: rtsx: Avoid mangling IRQ during runtime PM
+
+  * Enable Landlock by default (LP: #1953192)
+    - [Config] Enable Landlock by default
+
+  * Add s0i3 RTC wake up for AMD systems (LP: #1950013)
+    - platform/x86: amd-pmc: Export Idlemask values based on the APU
+    - platform/x86: amd-pmc: adjust arguments for `amd_pmc_send_cmd`
+    - platform/x86: amd-pmc: Add special handling for timer based S0i3 wakeup
+
+  * Fix runtime power management on USB controller with XHCI_RESET_ON_RESUME
+    flag (LP: #1954369)
+    - SAUCE: xhci: Remove CONFIG_USB_DEFAULT_PERSIST to prevent xHCI from runtime
+      suspending
+
+  * Fix System hangs on black screen when reboot (LP: #1949321)
+    - drm/i915/hdmi: convert intel_hdmi_to_dev to intel_hdmi_to_i915
+    - drm/i915: Don't request GMBUS to generate irqs when called while irqs are
+      off
+    - drm/i915/hdmi: Turn DP++ TMDS output buffers back on in encoder->shutdown()
+
+  * require CAP_NET_ADMIN to attach N_HCI ldisc (LP: #1949516)
+    - Bluetooth: hci_ldisc: require CAP_NET_ADMIN to attach N_HCI ldisc
+
+  * mt7921e: Failed to start WM firmware (LP: #1954300)
+    - SAUCE: Bluetooth: btusb: Handle download_firmware failure cases
+    - SAUCE: Bluetooth: btusb: Return error code when getting patch status failed
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Add list of built-in modules to the ABI
+    - [Packaging] abi-check: Process modules.builtin
+    - SAUCE: allow to use __wake_up_pollfree() from GPL modules
+    - [Packaging] enforce xz compression for debs
+    - [Config] update config after v5.15.12
+    - [Packaging] temporarily disable signed v4l2loopback
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 04 Jan 2022 11:22:10 +0100
+
+linux (5.15.0-14.14) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-14.14 -proposed tracker (LP: #1954627)
+
+  * Jammy update: v5.15.7 upstream stable release (LP: #1953731)
+    - ALSA: usb-audio: Restrict rates for the shared clocks
+    - ALSA: usb-audio: Rename early_playback_start flag with lowlatency_playback
+    - ALSA: usb-audio: Disable low-latency playback for free-wheel mode
+    - ALSA: usb-audio: Disable low-latency mode for implicit feedback sync
+    - ALSA: usb-audio: Check available frames for the next packet size
+    - ALSA: usb-audio: Add spinlock to stop_urbs()
+    - ALSA: usb-audio: Improved lowlatency playback support
+    - ALSA: usb-audio: Avoid killing in-flight URBs during draining
+    - ALSA: usb-audio: Fix packet size calculation regression
+    - ALSA: usb-audio: Less restriction for low-latency playback mode
+    - ALSA: usb-audio: Switch back to non-latency mode at a later point
+    - ALSA: usb-audio: Don't start stream for capture at prepare
+    - gfs2: release iopen glock early in evict
+    - gfs2: Fix length of holes reported at end-of-file
+    - powerpc/pseries/ddw: Revert "Extend upper limit for huge DMA window for
+      persistent memory"
+    - powerpc/pseries/ddw: Do not try direct mapping with persistent memory and
+      one window
+    - drm/sun4i: fix unmet dependency on RESET_CONTROLLER for PHY_SUN6I_MIPI_DPHY
+    - mac80211: do not access the IV when it was stripped
+    - mac80211: fix throughput LED trigger
+    - x86/hyperv: Move required MSRs check to initial platform probing
+    - net/smc: Transfer remaining wait queue entries during fallback
+    - atlantic: Fix OOB read and write in hw_atl_utils_fw_rpc_wait
+    - net: return correct error code
+    - pinctrl: qcom: fix unmet dependencies on GPIOLIB for GPIOLIB_IRQCHIP
+    - platform/x86: dell-wmi-descriptor: disable by default
+    - platform/x86: thinkpad_acpi: Add support for dual fan control
+    - platform/x86: thinkpad_acpi: Fix WWAN device disabled issue after S3 deep
+    - s390/setup: avoid using memblock_enforce_memory_limit
+    - btrfs: silence lockdep when reading chunk tree during mount
+    - btrfs: check-integrity: fix a warning on write caching disabled disk
+    - thermal: core: Reset previous low and high trip during thermal zone init
+    - scsi: iscsi: Unblock session then wake up error handler
+    - drm/amd/pm: Remove artificial freq level on Navi1x
+    - drm/amd/amdkfd: Fix kernel panic when reset failed and been triggered again
+    - drm/amd/amdgpu: fix potential memleak
+    - ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile
+    - ata: libahci: Adjust behavior when StorageD3Enable _DSD is set
+    - ethernet: hisilicon: hns: hns_dsaf_misc: fix a possible array overflow in
+      hns_dsaf_ge_srst_by_port()
+    - ipv6: check return value of ipv6_skip_exthdr
+    - net: tulip: de4x5: fix the problem that the array 'lp->phy[8]' may be out of
+      bound
+    - net: ethernet: dec: tulip: de4x5: fix possible array overflows in
+      type3_infoblock()
+    - perf sort: Fix the 'weight' sort key behavior
+    - perf sort: Fix the 'ins_lat' sort key behavior
+    - perf sort: Fix the 'p_stage_cyc' sort key behavior
+    - perf inject: Fix ARM SPE handling
+    - perf hist: Fix memory leak of a perf_hpp_fmt
+    - perf report: Fix memory leaks around perf_tip()
+    - tracing: Don't use out-of-sync va_list in event printing
+    - net/smc: Avoid warning of possible recursive locking
+    - ACPI: Add stubs for wakeup handler functions
+    - net/tls: Fix authentication failure in CCM mode
+    - vrf: Reset IPCB/IP6CB when processing outbound pkts in vrf dev xmit
+    - kprobes: Limit max data_size of the kretprobe instances
+    - ALSA: hda/cs8409: Set PMSG_ON earlier inside cs8409 driver
+    - rt2x00: do not mark device gone on EPROTO errors during start
+    - ipmi: Move remove_work to dedicated workqueue
+    - cpufreq: Fix get_cpu_device() failure in add_cpu_dev_symlink()
+    - iwlwifi: mvm: retry init flow if failed
+    - dma-buf: system_heap: Use 'for_each_sgtable_sg' in pages free flow
+    - s390/pci: move pseudo-MMIO to prevent MIO overlap
+    - fget: check that the fd still exists after getting a ref to it
+    - sata_fsl: fix UAF in sata_fsl_port_stop when rmmod sata_fsl
+    - sata_fsl: fix warning in remove_proc_entry when rmmod sata_fsl
+    - scsi: lpfc: Fix non-recovery of remote ports following an unsolicited LOGO
+    - scsi: ufs: ufs-pci: Add support for Intel ADL
+    - ipv6: fix memory leak in fib6_rule_suppress
+    - drm/amd/display: Allow DSC on supported MST branch devices
+    - drm/i915/dp: Perform 30ms delay after source OUI write
+    - KVM: fix avic_set_running for preemptable kernels
+    - KVM: Disallow user memslot with size that exceeds "unsigned long"
+    - KVM: x86/mmu: Fix TLB flush range when handling disconnected pt
+    - KVM: Ensure local memslot copies operate on up-to-date arch-specific data
+    - KVM: x86: ignore APICv if LAPIC is not enabled
+    - KVM: nVMX: Emulate guest TLB flush on nested VM-Enter with new vpid12
+    - KVM: nVMX: Flush current VPID (L1 vs. L2) for KVM_REQ_TLB_FLUSH_GUEST
+    - KVM: nVMX: Abide to KVM_REQ_TLB_FLUSH_GUEST request on nested vmentry/vmexit
+    - KVM: VMX: prepare sync_pir_to_irr for running with APICv disabled
+    - KVM: x86: Use a stable condition around all VT-d PI paths
+    - KVM: MMU: shadow nested paging does not have PKU
+    - KVM: arm64: Avoid setting the upper 32 bits of TCR_EL2 and CPTR_EL2 to 1
+    - KVM: X86: Use vcpu->arch.walk_mmu for kvm_mmu_invlpg()
+    - KVM: x86: check PIR even for vCPUs with disabled APICv
+    - tracing/histograms: String compares should not care about signed values
+    - net: dsa: mv88e6xxx: Fix application of erratum 4.8 for 88E6393X
+    - net: dsa: mv88e6xxx: Drop unnecessary check in
+      mv88e6393x_serdes_erratum_4_6()
+    - net: dsa: mv88e6xxx: Save power by disabling SerDes trasmitter and receiver
+    - net: dsa: mv88e6xxx: Add fix for erratum 5.2 of 88E6393X family
+    - net: dsa: mv88e6xxx: Fix inband AN for 2500base-x on 88E6393X family
+    - net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed
+    - wireguard: selftests: increase default dmesg log size
+    - wireguard: allowedips: add missing __rcu annotation to satisfy sparse
+    - wireguard: selftests: actually test for routing loops
+    - wireguard: selftests: rename DEBUG_PI_LIST to DEBUG_PLIST
+    - wireguard: device: reset peer src endpoint when netns exits
+    - wireguard: receive: use ring buffer for incoming handshakes
+    - wireguard: receive: drop handshakes if queue lock is contended
+    - wireguard: ratelimiter: use kvcalloc() instead of kvzalloc()
+    - i2c: stm32f7: flush TX FIFO upon transfer errors
+    - i2c: stm32f7: recover the bus on access timeout
+    - i2c: stm32f7: stop dma transfer in case of NACK
+    - i2c: cbus-gpio: set atomic transfer callback
+    - natsemi: xtensa: fix section mismatch warnings
+    - tcp: fix page frag corruption on page fault
+    - net: qlogic: qlcnic: Fix a NULL pointer dereference in
+      qlcnic_83xx_add_rings()
+    - net: mpls: Fix notifications when deleting a device
+    - siphash: use _unaligned version by default
+    - arm64: ftrace: add missing BTIs
+    - iwlwifi: fix warnings produced by kernel debug options
+    - net/mlx5e: IPsec: Fix Software parser inner l3 type setting in case of
+      encapsulation
+    - net/mlx4_en: Fix an use-after-free bug in mlx4_en_try_alloc_resources()
+    - selftests: net: Correct case name
+    - net: dsa: b53: Add SPI ID table
+    - mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_mode
+    - ASoC: tegra: Fix wrong value type in ADMAIF
+    - ASoC: tegra: Fix wrong value type in I2S
+    - ASoC: tegra: Fix wrong value type in DMIC
+    - ASoC: tegra: Fix wrong value type in DSPK
+    - ASoC: tegra: Fix kcontrol put callback in ADMAIF
+    - ASoC: tegra: Fix kcontrol put callback in I2S
+    - ASoC: tegra: Fix kcontrol put callback in DMIC
+    - ASoC: tegra: Fix kcontrol put callback in DSPK
+    - ASoC: tegra: Fix kcontrol put callback in AHUB
+    - rxrpc: Fix rxrpc_peer leak in rxrpc_look_up_bundle()
+    - rxrpc: Fix rxrpc_local leak in rxrpc_lookup_peer()
+    - ALSA: intel-dsp-config: add quirk for CML devices based on ES8336 codec
+    - net: stmmac: Avoid DMA_CHAN_CONTROL write if no Split Header support
+    - net: usb: lan78xx: lan78xx_phy_init(): use PHY_POLL instead of "0" if no IRQ
+      is available
+    - net: marvell: mvpp2: Fix the computation of shared CPUs
+    - dpaa2-eth: destroy workqueue at the end of remove function
+    - octeontx2-af: Fix a memleak bug in rvu_mbox_init()
+    - net: annotate data-races on txq->xmit_lock_owner
+    - ipv4: convert fib_num_tclassid_users to atomic_t
+    - net/smc: fix wrong list_del in smc_lgr_cleanup_early
+    - net/rds: correct socket tunable error in rds_tcp_tune()
+    - net/smc: Keep smc_close_final rc during active close
+    - drm/msm/a6xx: Allocate enough space for GMU registers
+    - drm/msm: Do hw_init() before capturing GPU state
+    - drm/vc4: kms: Wait for the commit before increasing our clock rate
+    - drm/vc4: kms: Fix return code check
+    - drm/vc4: kms: Add missing drm_crtc_commit_put
+    - drm/vc4: kms: Clear the HVS FIFO commit pointer once done
+    - drm/vc4: kms: Don't duplicate pending commit
+    - drm/vc4: kms: Fix previous HVS commit wait
+    - atlantic: Increase delay for fw transactions
+    - atlatnic: enable Nbase-t speeds with base-t
+    - atlantic: Fix to display FW bundle version instead of FW mac version.
+    - atlantic: Add missing DIDs and fix 115c.
+    - Remove Half duplex mode speed capabilities.
+    - atlantic: Fix statistics logic for production hardware
+    - atlantic: Remove warn trace message.
+    - KVM: x86/mmu: Skip tlb flush if it has been done in zap_gfn_range()
+    - KVM: x86/mmu: Pass parameter flush as false in
+      kvm_tdp_mmu_zap_collapsible_sptes()
+    - drm/msm/devfreq: Fix OPP refcnt leak
+    - drm/msm: Fix mmap to include VM_IO and VM_DONTDUMP
+    - drm/msm: Fix wait_fence submitqueue leak
+    - drm/msm: Restore error return on invalid fence
+    - ASoC: rk817: Add module alias for rk817-codec
+    - iwlwifi: Fix memory leaks in error handling path
+    - KVM: X86: Fix when shadow_root_level=5 && guest root_level<4
+    - KVM: SEV: initialize regions_list of a mirror VM
+    - net/mlx5e: Fix missing IPsec statistics on uplink representor
+    - net/mlx5: Move MODIFY_RQT command to ignore list in internal error state
+    - net/mlx5: E-switch, Respect BW share of the new group
+    - net/mlx5: E-Switch, fix single FDB creation on BlueField
+    - net/mlx5: E-Switch, Check group pointer before reading bw_share value
+    - KVM: x86/pmu: Fix reserved bits for AMD PerfEvtSeln register
+    - KVM: VMX: Set failure code in prepare_vmcs02()
+    - mctp: Don't let RTM_DELROUTE delete local routes
+    - Revert "drm/i915: Implement Wa_1508744258"
+    - io-wq: don't retry task_work creation failure on fatal conditions
+    - x86/sev: Fix SEV-ES INS/OUTS instructions for word, dword, and qword
+    - x86/entry: Add a fence for kernel entry SWAPGS in paranoid_entry()
+    - x86/entry: Use the correct fence macro after swapgs in kernel CR3
+    - x86/xen: Add xenpv_restore_regs_and_return_to_usermode()
+    - preempt/dynamic: Fix setup_preempt_mode() return value
+    - sched/uclamp: Fix rq->uclamp_max not set on first enqueue
+    - KVM: SEV: Return appropriate error codes if SEV-ES scratch setup fails
+    - KVM: x86/mmu: Rename slot_handle_leaf to slot_handle_level_4k
+    - KVM: x86/mmu: Remove spurious TLB flushes in TDP MMU zap collapsible path
+    - net/mlx5e: Rename lro_timeout to packet_merge_timeout
+    - net/mlx5e: Rename TIR lro functions to TIR packet merge functions
+    - net/mlx5e: Sync TIR params updates against concurrent create/modify
+    - serial: 8250_bcm7271: UART errors after resuming from S2
+    - parisc: Fix KBUILD_IMAGE for self-extracting kernel
+    - parisc: Fix "make install" on newer debian releases
+    - parisc: Mark cr16 CPU clocksource unstable on all SMP machines
+    - vgacon: Propagate console boot parameters before calling `vc_resize'
+    - xhci: Fix commad ring abort, write all 64 bits to CRCR register.
+    - USB: NO_LPM quirk Lenovo Powered USB-C Travel Hub
+    - usb: typec: tcpm: Wait in SNK_DEBOUNCED until disconnect
+    - usb: cdns3: gadget: fix new urb never complete if ep cancel previous
+      requests
+    - usb: cdnsp: Fix a NULL pointer dereference in cdnsp_endpoint_init()
+    - x86/tsc: Add a timer to make sure TSC_adjust is always checked
+    - x86/tsc: Disable clocksource watchdog for TSC on qualified platorms
+    - x86/64/mm: Map all kernel memory into trampoline_pgd
+    - tty: serial: msm_serial: Deactivate RX DMA for polling support
+    - serial: pl011: Add ACPI SBSA UART match id
+    - serial: tegra: Change lower tolerance baud rate limit for tegra20 and
+      tegra30
+    - serial: core: fix transmit-buffer reset and memleak
+    - serial: 8250_pci: Fix ACCES entries in pci_serial_quirks array
+    - serial: 8250_pci: rewrite pericom_do_set_divisor()
+    - serial: 8250: Fix RTS modem control while in rs485 mode
+    - serial: liteuart: Fix NULL pointer dereference in ->remove()
+    - serial: liteuart: fix use-after-free and memleak on unbind
+    - serial: liteuart: fix minor-number leak on probe errors
+    - ipmi: msghandler: Make symbol 'remove_work_wq' static
+    - Linux 5.15.7
+
+  * Updates to ib_peer_memory requested by Nvidia (LP: #1947206)
+    - SAUCE: RDMA/core: Updated ib_peer_memory
+    - SAUCE: RDMA/core: ib_peer_memory fix build errors
+
+  * Jammy update: v5.15.6 upstream stable release (LP: #1953370)
+    - scsi: sd: Fix sd_do_mode_sense() buffer length handling
+    - ACPI: Get acpi_device's parent from the parent field
+    - ACPI: CPPC: Add NULL pointer check to cppc_get_perf()
+    - USB: serial: pl2303: fix GC type detection
+    - USB: serial: option: add Telit LE910S1 0x9200 composition
+    - USB: serial: option: add Fibocom FM101-GL variants
+    - usb: dwc2: gadget: Fix ISOC flow for elapsed frames
+    - usb: dwc2: hcd_queue: Fix use of floating point literal
+    - usb: dwc3: leave default DMA for PCI devices
+    - usb: dwc3: core: Revise GHWPARAMS9 offset
+    - usb: dwc3: gadget: Ignore NoStream after End Transfer
+    - usb: dwc3: gadget: Check for L1/L2/U3 for Start Transfer
+    - usb: dwc3: gadget: Fix null pointer exception
+    - net: usb: Correct PHY handling of smsc95xx
+    - net: nexthop: fix null pointer dereference when IPv6 is not enabled
+    - usb: chipidea: ci_hdrc_imx: fix potential error pointer dereference in probe
+    - usb: typec: fusb302: Fix masking of comparator and bc_lvl interrupts
+    - usb: xhci: tegra: Check padctrl interrupt presence in device tree
+    - usb: hub: Fix usb enumeration issue due to address0 race
+    - usb: hub: Fix locking issues with address0_mutex
+    - binder: fix test regression due to sender_euid change
+    - ALSA: ctxfi: Fix out-of-range access
+    - ALSA: hda/realtek: Add quirk for ASRock NUC Box 1100
+    - ALSA: hda/realtek: Fix LED on HP ProBook 435 G7
+    - media: cec: copy sequence field for the reply
+    - Revert "parisc: Fix backtrace to always include init funtion names"
+    - HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts
+    - staging/fbtft: Fix backlight
+    - staging: greybus: Add missing rwsem around snd_ctl_remove() calls
+    - staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()
+    - staging: r8188eu: Use kzalloc() with GFP_ATOMIC in atomic context
+    - staging: r8188eu: Fix breakage introduced when 5G code was removed
+    - staging: r8188eu: use GFP_ATOMIC under spinlock
+    - staging: r8188eu: fix a memory leak in rtw_wx_read32()
+    - fuse: release pipe buf after last use
+    - xen: don't continue xenstore initialization in case of errors
+    - xen: detect uninitialized xenbus in xenbus_init
+    - io_uring: correct link-list traversal locking
+    - io_uring: fail cancellation for EXITING tasks
+    - io_uring: fix link traversal locking
+    - drm/amdgpu: IH process reset count when restart
+    - drm/amdgpu/pm: fix powerplay OD interface
+    - drm/nouveau: recognise GA106
+    - ksmbd: downgrade addition info error msg to debug in smb2_get_info_sec()
+    - ksmbd: contain default data stream even if xattr is empty
+    - ksmbd: fix memleak in get_file_stream_info()
+    - KVM: PPC: Book3S HV: Prevent POWER7/8 TLB flush flushing SLB
+    - tracing/uprobe: Fix uprobe_perf_open probes iteration
+    - tracing: Fix pid filtering when triggers are attached
+    - mmc: sdhci-esdhc-imx: disable CMDQ support
+    - mmc: sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
+    - mdio: aspeed: Fix "Link is Down" issue
+    - arm64: mm: Fix VM_BUG_ON(mm != &init_mm) for trans_pgd
+    - cpufreq: intel_pstate: Fix active mode offline/online EPP handling
+    - powerpc/32: Fix hardlockup on vmap stack overflow
+    - iomap: Fix inline extent handling in iomap_readpage
+    - NFSv42: Fix pagecache invalidation after COPY/CLONE
+    - PCI: aardvark: Deduplicate code in advk_pcie_rd_conf()
+    - PCI: aardvark: Implement re-issuing config requests on CRS response
+    - PCI: aardvark: Simplify initialization of rootcap on virtual bridge
+    - PCI: aardvark: Fix link training
+    - drm/amd/display: Fix OLED brightness control on eDP
+    - proc/vmcore: fix clearing user buffer by properly using clear_user()
+    - ASoC: SOF: Intel: hda: fix hotplug when only codec is suspended
+    - netfilter: ctnetlink: fix filtering with CTA_TUPLE_REPLY
+    - netfilter: ctnetlink: do not erase error code with EINVAL
+    - netfilter: ipvs: Fix reuse connection if RS weight is 0
+    - netfilter: flowtable: fix IPv6 tunnel addr match
+    - media: v4l2-core: fix VIDIOC_DQEVENT handling on non-x86
+    - firmware: arm_scmi: Fix null de-reference on error path
+    - ARM: dts: BCM5301X: Fix I2C controller interrupt
+    - ARM: dts: BCM5301X: Add interrupt properties to GPIO node
+    - ARM: dts: bcm2711: Fix PCIe interrupts
+    - ASoC: qdsp6: q6routing: Conditionally reset FrontEnd Mixer
+    - ASoC: qdsp6: q6asm: fix q6asm_dai_prepare error handling
+    - ASoC: topology: Add missing rwsem around snd_ctl_remove() calls
+    - ASoC: codecs: wcd938x: fix volatile register range
+    - ASoC: codecs: wcd934x: return error code correctly from hw_params
+    - ASoC: codecs: lpass-rx-macro: fix HPHR setting CLSH mask
+    - net: ieee802154: handle iftypes as u32
+    - firmware: arm_scmi: Fix base agent discover response
+    - firmware: arm_scmi: pm: Propagate return value to caller
+    - ASoC: stm32: i2s: fix 32 bits channel length without mclk
+    - NFSv42: Don't fail clone() unless the OP_CLONE operation failed
+    - ARM: socfpga: Fix crash with CONFIG_FORTIRY_SOURCE
+    - drm/nouveau/acr: fix a couple NULL vs IS_ERR() checks
+    - scsi: qla2xxx: edif: Fix off by one bug in qla_edif_app_getfcinfo()
+    - scsi: mpt3sas: Fix kernel panic during drive powercycle test
+    - scsi: mpt3sas: Fix system going into read-only mode
+    - scsi: mpt3sas: Fix incorrect system timestamp
+    - drm/vc4: fix error code in vc4_create_object()
+    - drm/aspeed: Fix vga_pw sysfs output
+    - net: marvell: prestera: fix brige port operation
+    - net: marvell: prestera: fix double free issue on err path
+    - HID: input: Fix parsing of HID_CP_CONSUMER_CONTROL fields
+    - HID: input: set usage type to key on keycode remap
+    - HID: magicmouse: prevent division by 0 on scroll
+    - iavf: Prevent changing static ITR values if adaptive moderation is on
+    - iavf: Fix refreshing iavf adapter stats on ethtool request
+    - iavf: Fix VLAN feature flags after VFR
+    - x86/pvh: add prototype for xen_pvh_init()
+    - xen/pvh: add missing prototype to header
+    - ALSA: intel-dsp-config: add quirk for JSL devices based on ES8336 codec
+    - mptcp: fix delack timer
+    - mptcp: use delegate action to schedule 3rd ack retrans
+    - af_unix: fix regression in read after shutdown
+    - firmware: smccc: Fix check for ARCH_SOC_ID not implemented
+    - ipv6: fix typos in __ip6_finish_output()
+    - nfp: checking parameter process for rx-usecs/tx-usecs is invalid
+    - net: stmmac: retain PTP clock time during SIOCSHWTSTAMP ioctls
+    - net: ipv6: add fib6_nh_release_dsts stub
+    - net: nexthop: release IPv6 per-cpu dsts when replacing a nexthop group
+    - ice: fix vsi->txq_map sizing
+    - ice: avoid bpf_prog refcount underflow
+    - scsi: core: sysfs: Fix setting device state to SDEV_RUNNING
+    - scsi: scsi_debug: Zero clear zones at reset write pointer
+    - erofs: fix deadlock when shrink erofs slab
+    - i2c: virtio: disable timeout handling
+    - net/smc: Ensure the active closing peer first closes clcsock
+    - mlxsw: spectrum: Protect driver from buggy firmware
+    - net: ipa: directly disable ipa-setup-ready interrupt
+    - net: ipa: separate disabling setup from modem stop
+    - net: ipa: kill ipa_cmd_pipeline_clear()
+    - net: marvell: mvpp2: increase MTU limit when XDP enabled
+    - cpufreq: intel_pstate: Add Ice Lake server to out-of-band IDs
+    - nvmet-tcp: fix incomplete data digest send
+    - drm/hyperv: Fix device removal on Gen1 VMs
+    - arm64: uaccess: avoid blocking within critical sections
+    - net/ncsi : Add payload to be 32-bit aligned to fix dropped packets
+    - PM: hibernate: use correct mode for swsusp_close()
+    - drm/amd/display: Fix DPIA outbox timeout after GPU reset
+    - drm/amd/display: Set plane update flags for all planes in reset
+    - tcp_cubic: fix spurious Hystart ACK train detections for not-cwnd-limited
+      flows
+    - lan743x: fix deadlock in lan743x_phy_link_status_change()
+    - net: phylink: Force link down and retrigger resolve on interface change
+    - net: phylink: Force retrigger in case of latched link-fail indicator
+    - net/smc: Fix NULL pointer dereferencing in smc_vlan_by_tcpsk()
+    - net/smc: Fix loop in smc_listen
+    - nvmet: use IOCB_NOWAIT only if the filesystem supports it
+    - igb: fix netpoll exit with traffic
+    - MIPS: loongson64: fix FTLB configuration
+    - MIPS: use 3-level pgtable for 64KB page size on MIPS_VA_BITS_48
+    - tls: splice_read: fix record type check
+    - tls: splice_read: fix accessing pre-processed records
+    - tls: fix replacing proto_ops
+    - net: stmmac: Disable Tx queues when reconfiguring the interface
+    - net/sched: sch_ets: don't peek at classes beyond 'nbands'
+    - ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
+    - net: vlan: fix underflow for the real_dev refcnt
+    - net/smc: Don't call clcsock shutdown twice when smc shutdown
+    - net: hns3: fix VF RSS failed problem after PF enable multi-TCs
+    - net: hns3: fix incorrect components info of ethtool --reset command
+    - net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
+    - net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
+    - locking/rwsem: Make handoff bit handling more consistent
+    - perf: Ignore sigtrap for tracepoints destined for other tasks
+    - sched/scs: Reset task stack state in bringup_cpu()
+    - iommu/rockchip: Fix PAGE_DESC_HI_MASKs for RK3568
+    - iommu/vt-d: Fix unmap_pages support
+    - f2fs: quota: fix potential deadlock
+    - f2fs: set SBI_NEED_FSCK flag when inconsistent node block found
+    - riscv: dts: microchip: fix board compatible
+    - riscv: dts: microchip: drop duplicated MMC/SDHC node
+    - cifs: nosharesock should not share socket with future sessions
+    - ceph: properly handle statfs on multifs setups
+    - iommu/amd: Clarify AMD IOMMUv2 initialization messages
+    - vdpa_sim: avoid putting an uninitialized iova_domain
+    - vhost/vsock: fix incorrect used length reported to the guest
+    - ksmbd: Fix an error handling path in 'smb2_sess_setup()'
+    - tracing: Check pid filtering when creating events
+    - cifs: nosharesock should be set on new server
+    - io_uring: fix soft lockup when call __io_remove_buffers
+    - firmware: arm_scmi: Fix type error assignment in voltage protocol
+    - firmware: arm_scmi: Fix type error in sensor protocol
+    - docs: accounting: update delay-accounting.rst reference
+    - blk-mq: cancel blk-mq dispatch work in both blk_cleanup_queue and
+      disk_release()
+    - block: avoid to quiesce queue in elevator_init_mq
+    - drm/amdgpu/gfx10: add wraparound gpu counter check for APUs as well
+    - drm/amdgpu/gfx9: switch to golden tsc registers for renoir+
+    - Linux 5.15.6
+
+  * Fix bogus HDMI audio interface  (LP: #1953208)
+    - ALSA: hda/hdmi: Consider ELD is invalid when no SAD is present
+
+  * Miscellaneous Ubuntu changes
+    - [Config] re-enabled UBSAN without TRAP
+    - SAUCE: ipv6: fix NULL pointer dereference in ip6_output()
+    - SAUCE: RDMA/core: Introduce peer memory interface
+    - [Config] toolchain version update
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] Temporarily disable signing for ppc64el and s390x"
+    - Revert "UBUNTU: SAUCE: vt -- maintain bootloader screen mode and content
+      until vt switch"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 13 Dec 2021 12:13:17 +0100
+
+linux (5.15.0-13.13) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-13.13 -proposed tracker (LP: #1952583)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Jammy update: v5.15.5 upstream stable release (LP: #1952579)
+    - arm64: zynqmp: Do not duplicate flash partition label property
+    - arm64: zynqmp: Fix serial compatible string
+    - clk: sunxi-ng: Unregister clocks/resets when unbinding
+    - ARM: dts: sunxi: Fix OPPs node name
+    - arm64: dts: allwinner: h5: Fix GPU thermal zone node name
+    - arm64: dts: allwinner: a100: Fix thermal zone node name
+    - staging: wfx: ensure IRQ is ready before enabling it
+    - ARM: dts: BCM5301X: Fix nodes names
+    - ARM: dts: BCM5301X: Fix MDIO mux binding
+    - ARM: dts: NSP: Fix mpcore, mmc node names
+    - arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus
+    - scsi: pm80xx: Fix memory leak during rmmod
+    - scsi: lpfc: Fix list_add() corruption in lpfc_drain_txq()
+    - ASoC: mediatek: mt8195: Add missing of_node_put()
+    - arm64: dts: rockchip: Disable CDN DP on Pinebook Pro
+    - arm64: dts: hisilicon: fix arm,sp805 compatible string
+    - RDMA/bnxt_re: Check if the vlan is valid before reporting
+    - bus: ti-sysc: Add quirk handling for reinit on context lost
+    - bus: ti-sysc: Use context lost quirk for otg
+    - usb: musb: tusb6010: check return value after calling
+      platform_get_resource()
+    - usb: typec: tipd: Remove WARN_ON in tps6598x_block_read
+    - ARM: dts: ux500: Skomer regulator fixes
+    - staging: rtl8723bs: remove possible deadlock when disconnect (v2)
+    - staging: rtl8723bs: remove a second possible deadlock
+    - staging: rtl8723bs: remove a third possible deadlock
+    - ARM: BCM53016: Specify switch ports for Meraki MR32
+    - arm64: dts: qcom: msm8998: Fix CPU/L2 idle state latency and residency
+    - arm64: dts: qcom: ipq6018: Fix qcom,controlled-remotely property
+    - arm64: dts: qcom: ipq8074: Fix qcom,controlled-remotely property
+    - arm64: dts: qcom: sdm845: Fix qcom,controlled-remotely property
+    - arm64: dts: freescale: fix arm,sp805 compatible string
+    - arm64: dts: ls1012a: Add serial alias for ls1012a-rdb
+    - RDMA/rxe: Separate HW and SW l/rkeys
+    - ASoC: SOF: Intel: hda-dai: fix potential locking issue
+    - scsi: core: Fix scsi_mode_sense() buffer length handling
+    - ALSA: usb-audio: disable implicit feedback sync for Behringer UFX1204 and
+      UFX1604
+    - clk: imx: imx6ul: Move csi_sel mux to correct base register
+    - ASoC: es8316: Use IRQF_NO_AUTOEN when requesting the IRQ
+    - ASoC: rt5651: Use IRQF_NO_AUTOEN when requesting the IRQ
+    - ASoC: nau8824: Add DMI quirk mechanism for active-high jack-detect
+    - scsi: advansys: Fix kernel pointer leak
+    - scsi: smartpqi: Add controller handshake during kdump
+    - arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY
+    - ALSA: intel-dsp-config: add quirk for APL/GLK/TGL devices based on ES8336
+      codec
+    - ASoC: Intel: soc-acpi: add missing quirk for TGL SDCA single amp
+    - ASoC: Intel: sof_sdw: add missing quirk for Dell SKU 0A45
+    - firmware_loader: fix pre-allocated buf built-in firmware use
+    - HID: multitouch: disable sticky fingers for UPERFECT Y
+    - ALSA: usb-audio: Add support for the Pioneer DJM 750MK2 Mixer/Soundcard
+    - ARM: dts: omap: fix gpmc,mux-add-data type
+    - usb: host: ohci-tmio: check return value after calling
+      platform_get_resource()
+    - ASoC: rt5682: fix a little pop while playback
+    - ARM: dts: ls1021a: move thermal-zones node out of soc/
+    - ARM: dts: ls1021a-tsn: use generic "jedec,spi-nor" compatible for flash
+    - ALSA: ISA: not for M68K
+    - iommu/vt-d: Do not falsely log intel_iommu is unsupported kernel option
+    - tty: tty_buffer: Fix the softlockup issue in flush_to_ldisc
+    - MIPS: sni: Fix the build
+    - scsi: scsi_debug: Fix out-of-bound read in resp_readcap16()
+    - scsi: scsi_debug: Fix out-of-bound read in resp_report_tgtpgs()
+    - scsi: target: Fix ordered tag handling
+    - scsi: target: Fix alua_tg_pt_gps_count tracking
+    - iio: imu: st_lsm6dsx: Avoid potential array overflow in st_lsm6dsx_set_odr()
+    - RDMA/core: Use kvzalloc when allocating the struct ib_port
+    - scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
+    - scsi: lpfc: Fix link down processing to address NULL pointer dereference
+    - scsi: lpfc: Allow fabric node recovery if recovery is in progress before
+      devloss
+    - memory: tegra20-emc: Add runtime dependency on devfreq governor module
+    - powerpc/5200: dts: fix memory node unit name
+    - ARM: dts: qcom: fix memory and mdio nodes naming for RB3011
+    - arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
+    - ALSA: gus: fix null pointer dereference on pointer block
+    - ALSA: usb-audio: fix null pointer dereference on pointer cs_desc
+    - clk: at91: sama7g5: remove prescaler part of master clock
+    - iommu/dart: Initialize DART_STREAMS_ENABLE
+    - powerpc/dcr: Use cmplwi instead of 3-argument cmpli
+    - powerpc/8xx: Fix Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST
+    - sh: check return code of request_irq
+    - maple: fix wrong return value of maple_bus_init().
+    - f2fs: fix up f2fs_lookup tracepoints
+    - f2fs: fix to use WHINT_MODE
+    - f2fs: fix wrong condition to trigger background checkpoint correctly
+    - sh: fix kconfig unmet dependency warning for FRAME_POINTER
+    - sh: math-emu: drop unused functions
+    - sh: define __BIG_ENDIAN for math-emu
+    - f2fs: compress: disallow disabling compress on non-empty compressed file
+    - f2fs: fix incorrect return value in f2fs_sanity_check_ckpt()
+    - clk: ingenic: Fix bugs with divided dividers
+    - clk/ast2600: Fix soc revision for AHB
+    - clk: qcom: gcc-msm8996: Drop (again) gcc_aggre1_pnoc_ahb_clk
+    - KVM: arm64: Fix host stage-2 finalization
+    - mips: BCM63XX: ensure that CPU_SUPPORTS_32BIT_KERNEL is set
+    - MIPS: boot/compressed/: add __bswapdi2() to target for ZSTD decompression
+    - sched/core: Mitigate race cpus_share_cache()/update_top_cache_domain()
+    - sched/fair: Prevent dead task groups from regaining cfs_rq's
+    - perf/x86/vlbr: Add c->flags to vlbr event constraints
+    - blkcg: Remove extra blkcg_bio_issue_init
+    - tracing/histogram: Do not copy the fixed-size char array field over the
+      field size
+    - perf bpf: Avoid memory leak from perf_env__insert_btf()
+    - perf bench futex: Fix memory leak of perf_cpu_map__new()
+    - perf tests: Remove bash construct from record+zstd_comp_decomp.sh
+    - drm/nouveau: hdmigv100.c: fix corrupted HDMI Vendor InfoFrame
+    - bpf: Fix inner map state pruning regression.
+    - samples/bpf: Fix summary per-sec stats in xdp_sample_user
+    - samples/bpf: Fix incorrect use of strlen in xdp_redirect_cpu
+    - selftests: net: switch to socat in the GSO GRE test
+    - net/ipa: ipa_resource: Fix wrong for loop range
+    - tcp: Fix uninitialized access in skb frags array for Rx 0cp.
+    - tracing: Add length protection to histogram string copies
+    - nl80211: fix radio statistics in survey dump
+    - mac80211: fix monitor_sdata RCU/locking assertions
+    - net: ipa: HOLB register sometimes must be written twice
+    - net: ipa: disable HOLB drop when updating timer
+    - selftests: gpio: fix gpio compiling error
+    - net: bnx2x: fix variable dereferenced before check
+    - bnxt_en: reject indirect blk offload when hw-tc-offload is off
+    - tipc: only accept encrypted MSG_CRYPTO msgs
+    - sock: fix /proc/net/sockstat underflow in sk_clone_lock()
+    - net/smc: Make sure the link_id is unique
+    - NFSD: Fix exposure in nfsd4_decode_bitmap()
+    - iavf: Fix return of set the new channel count
+    - iavf: check for null in iavf_fix_features
+    - iavf: free q_vectors before queues in iavf_disable_vf
+    - iavf: don't clear a lock we don't hold
+    - iavf: Fix failure to exit out from last all-multicast mode
+    - iavf: prevent accidental free of filter structure
+    - iavf: validate pointers
+    - iavf: Fix for the false positive ASQ/ARQ errors while issuing VF reset
+    - iavf: Fix for setting queues to 0
+    - iavf: Restore VLAN filters after link down
+    - bpf: Fix toctou on read-only map's constant scalar tracking
+    - MIPS: generic/yamon-dt: fix uninitialized variable error
+    - mips: bcm63xx: add support for clk_get_parent()
+    - mips: lantiq: add support for clk_get_parent()
+    - gpio: rockchip: needs GENERIC_IRQ_CHIP to fix build errors
+    - platform/x86: hp_accel: Fix an error handling path in 'lis3lv02d_probe()'
+    - platform/x86: think-lmi: Abort probe on analyze failure
+    - udp: Validate checksum in udp_read_sock()
+    - btrfs: make 1-bit bit-fields of scrub_page unsigned int
+    - RDMA/core: Set send and receive CQ before forwarding to the driver
+    - net/mlx5e: kTLS, Fix crash in RX resync flow
+    - net/mlx5e: Wait for concurrent flow deletion during neigh/fib events
+    - net/mlx5: E-Switch, Fix resetting of encap mode when entering switchdev
+    - net/mlx5e: nullify cq->dbg pointer in mlx5_debug_cq_remove()
+    - net/mlx5: Update error handler for UCTX and UMEM
+    - net/mlx5: E-Switch, rebuild lag only when needed
+    - net/mlx5e: CT, Fix multiple allocations and memleak of mod acts
+    - net/mlx5: Lag, update tracker when state change event received
+    - net/mlx5: E-Switch, return error if encap isn't supported
+    - scsi: ufs: core: Improve SCSI abort handling
+    - scsi: core: sysfs: Fix hang when device state is set via sysfs
+    - scsi: ufs: core: Fix task management completion timeout race
+    - scsi: ufs: core: Fix another task management completion race
+    - net: mvmdio: fix compilation warning
+    - net: sched: act_mirred: drop dst for the direction from egress to ingress
+    - net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove
+    - net: virtio_net_hdr_to_skb: count transport header in UFO
+    - i40e: Fix correct max_pkt_size on VF RX queue
+    - i40e: Fix NULL ptr dereference on VSI filter sync
+    - i40e: Fix changing previously set num_queue_pairs for PFs
+    - i40e: Fix ping is lost after configuring ADq on VF
+    - RDMA/mlx4: Do not fail the registration on port stats
+    - i40e: Fix warning message and call stack during rmmod i40e driver
+    - i40e: Fix creation of first queue by omitting it if is not power of two
+    - i40e: Fix display error code in dmesg
+    - NFC: reorganize the functions in nci_request
+    - NFC: reorder the logic in nfc_{un,}register_device
+    - NFC: add NCI_UNREG flag to eliminate the race
+    - e100: fix device suspend/resume
+    - ptp: ocp: Fix a couple NULL vs IS_ERR() checks
+    - tools build: Fix removal of feature-sync-compare-and-swap feature detection
+    - riscv: fix building external modules
+    - KVM: PPC: Book3S HV: Use GLOBAL_TOC for kvmppc_h_set_dabr/xdabr()
+    - powerpc: clean vdso32 and vdso64 directories
+    - powerpc/pseries: rename numa_dist_table to form2_distances
+    - powerpc/pseries: Fix numa FORM2 parsing fallback code
+    - pinctrl: qcom: sdm845: Enable dual edge errata
+    - pinctrl: qcom: sm8350: Correct UFS and SDC offsets
+    - perf/x86/intel/uncore: Fix filter_tid mask for CHA events on Skylake Server
+    - perf/x86/intel/uncore: Fix IIO event constraints for Skylake Server
+    - perf/x86/intel/uncore: Fix IIO event constraints for Snowridge
+    - s390/kexec: fix return code handling
+    - blk-cgroup: fix missing put device in error path from blkg_conf_pref()
+    - dmaengine: remove debugfs #ifdef
+    - tun: fix bonding active backup with arp monitoring
+    - Revert "mark pstore-blk as broken"
+    - pstore/blk: Use "%lu" to format unsigned long
+    - hexagon: export raw I/O routines for modules
+    - hexagon: clean up timer-regs.h
+    - tipc: check for null after calling kmemdup
+    - ipc: WARN if trying to remove ipc object which is absent
+    - shm: extend forced shm destroy to support objects from several IPC nses
+    - mm: kmemleak: slob: respect SLAB_NOLEAKTRACE flag
+    - hugetlb, userfaultfd: fix reservation restore on userfaultfd error
+    - kmap_local: don't assume kmap PTEs are linear arrays in memory
+    - mm/damon/dbgfs: use '__GFP_NOWARN' for user-specified size buffer allocation
+    - mm/damon/dbgfs: fix missed use of damon_dbgfs_lock
+    - x86/boot: Pull up cmdline preparation and early param parsing
+    - x86/sgx: Fix free page accounting
+    - x86/hyperv: Fix NULL deref in set_hv_tscchange_cb() if Hyper-V setup fails
+    - KVM: x86: Assume a 64-bit hypercall for guests with protected state
+    - KVM: x86: Fix uninitialized eoi_exit_bitmap usage in vcpu_load_eoi_exitmap()
+    - KVM: x86/mmu: include EFER.LMA in extended mmu role
+    - KVM: x86/xen: Fix get_attr of KVM_XEN_ATTR_TYPE_SHARED_INFO
+    - powerpc/signal32: Fix sigset_t copy
+    - powerpc/xive: Change IRQ domain to a tree domain
+    - powerpc/8xx: Fix pinned TLBs with CONFIG_STRICT_KERNEL_RWX
+    - Revert "drm/i915/tgl/dsi: Gate the ddi clocks after pll mapping"
+    - Revert "parisc: Reduce sigreturn trampoline to 3 instructions"
+    - ata: libata: improve ata_read_log_page() error message
+    - ata: libata: add missing ata_identify_page_supported() calls
+    - scsi: qla2xxx: Fix mailbox direction flags in qla2xxx_get_adapter_id()
+    - pinctrl: ralink: include 'ralink_regs.h' in 'pinctrl-mt7620.c'
+    - s390/setup: avoid reserving memory above identity mapping
+    - s390/boot: simplify and fix kernel memory layout setup
+    - s390/vdso: filter out -mstack-guard and -mstack-size
+    - s390/kexec: fix memory leak of ipl report buffer
+    - s390/dump: fix copying to user-space of swapped kdump oldmem
+    - block: Check ADMIN before NICE for IOPRIO_CLASS_RT
+    - fbdev: Prevent probing generic drivers if a FB is already registered
+    - KVM: SEV: Disallow COPY_ENC_CONTEXT_FROM if target has created vCPUs
+    - KVM: nVMX: don't use vcpu->arch.efer when checking host state on nested
+      state load
+    - drm/cma-helper: Release non-coherent memory with dma_free_noncoherent()
+    - printk: restore flushing of NMI buffers on remote CPUs after NMI backtraces
+    - udf: Fix crash after seekdir
+    - spi: fix use-after-free of the add_lock mutex
+    - net: stmmac: socfpga: add runtime suspend/resume callback for stratix10
+      platform
+    - Drivers: hv: balloon: Use VMBUS_RING_SIZE() wrapper for dm_ring_size
+    - btrfs: fix memory ordering between normal and ordered work functions
+    - fs: handle circular mappings correctly
+    - net: stmmac: Fix signed/unsigned wreckage
+    - parisc/sticon: fix reverse colors
+    - cfg80211: call cfg80211_stop_ap when switch from P2P_GO type
+    - mac80211: fix radiotap header generation
+    - mac80211: drop check for DONT_REORDER in __ieee80211_select_queue
+    - drm/amd/display: Update swizzle mode enums
+    - drm/amd/display: Limit max DSC target bpp for specific monitors
+    - drm/i915/guc: Fix outstanding G2H accounting
+    - drm/i915/guc: Don't enable scheduling on a banned context, guc_id invalid,
+      not registered
+    - drm/i915/guc: Workaround reset G2H is received after schedule done G2H
+    - drm/i915/guc: Don't drop ce->guc_active.lock when unwinding context
+    - drm/i915/guc: Unwind context requests in reverse order
+    - drm/udl: fix control-message timeout
+    - drm/prime: Fix use after free in mmap with drm_gem_ttm_mmap
+    - drm/nouveau: Add a dedicated mutex for the clients list
+    - drm/nouveau: use drm_dev_unplug() during device removal
+    - drm/nouveau: clean up all clients on device removal
+    - drm/i915/dp: Ensure sink rate values are always valid
+    - drm/i915/dp: Ensure max link params are always valid
+    - drm/i915: Fix type1 DVI DP dual mode adapter heuristic for modern platforms
+    - drm/amdgpu: fix set scaling mode Full/Full aspect/Center not works on vga
+      and dvi connectors
+    - drm/amd/pm: avoid duplicate powergate/ungate setting
+    - signal: Implement force_fatal_sig
+    - exit/syscall_user_dispatch: Send ordinary signals on failure
+    - signal/powerpc: On swapcontext failure force SIGSEGV
+    - signal/s390: Use force_sigsegv in default_trap_handler
+    - signal/sparc32: Exit with a fatal signal when try_to_clear_window_buffer
+      fails
+    - signal/sparc32: In setup_rt_frame and setup_fram use force_fatal_sig
+    - signal/vm86_32: Properly send SIGSEGV when the vm86 state cannot be saved.
+    - signal/x86: In emulate_vsyscall force a signal instead of calling do_exit
+    - signal: Replace force_sigsegv(SIGSEGV) with force_fatal_sig(SIGSEGV)
+    - signal: Don't always set SA_IMMUTABLE for forced signals
+    - signal: Replace force_fatal_sig with force_exit_sig when in doubt
+    - hugetlbfs: flush TLBs correctly after huge_pmd_unshare
+    - RDMA/netlink: Add __maybe_unused to static inline in C file
+    - bpf: Forbid bpf_ktime_get_coarse_ns and bpf_timer_* in tracing progs
+    - selinux: fix NULL-pointer dereference when hashtab allocation fails
+    - ASoC: DAPM: Cover regression by kctl change notification fix
+    - ASoC: rsnd: fixup DMAEngine API
+    - usb: max-3421: Use driver data instead of maintaining a list of bound
+      devices
+    - ice: Fix VF true promiscuous mode
+    - ice: Delete always true check of PF pointer
+    - fs: export an inode_update_time helper
+    - btrfs: update device path inode time instead of bd_inode
+    - net: add and use skb_unclone_keeptruesize() helper
+    - x86/Kconfig: Fix an unused variable error in dell-smm-hwmon
+    - ALSA: hda: hdac_ext_stream: fix potential locking issues
+    - ALSA: hda: hdac_stream: fix potential locking issue in
+      snd_hdac_stream_assign()
+    - Linux 5.15.5
+
+  * Fix non-working e1000e device after resume (LP: #1951861)
+    - SAUCE: Revert "e1000e: Additional PHY power saving in S0ix"
+    - SAUCE: Revert "e1000e: Add polling mechanism to indicate CSME DPG exit"
+    - SAUCE: Revert "e1000e: Add handshake with the CSME to support S0ix"
+
+  * [SRU][I/OEM-5.13/OEM-5.14] Add MAC passthrough support for more Lenovo docks
+    (LP: #1951767)
+    - net: usb: r8152: Add MAC passthrough support for more Lenovo Docks
+
+  * [amdgpu] USB4 support for DP tunneling (LP: #1951868)
+    - drm/amd/display: Support for DMUB HPD interrupt handling
+    - drm/amd/display: Update link encoder object creation.
+    - drm/amd/display: USB4 DPIA enumeration and AUX Tunneling
+    - drm/amd/display: Support for DMUB HPD and HPD RX interrupt handling
+    - drm/amd/display: Set DPIA link endpoint type
+    - drm/amd/display: Stub out DPIA link training call
+    - drm/amd/display: Add stub to get DPIA tunneling device data
+    - drm/amd/display: Skip DPCD read for DPTX-to-DPIA hop
+    - drm/amd/display: Train DPIA links with fallback
+    - drm/amd/display: Implement DPIA training loop
+    - drm/amd/display: Implement DPIA link configuration
+    - drm/amd/display: Implement DPIA clock recovery phase
+    - drm/amd/display: Implement DPIA equalisation phase
+    - drm/amd/display: Implement end of training for hop in DPIA display path
+    - drm/amd/display: Support for SET_CONFIG processing with DMUB
+    - drm/amd/display: isolate link training setting override to its own function
+    - drm/amd/display: Read USB4 DP tunneling data from DPCD.
+    - drm/amd/display: Add dpia debug options
+    - drm/amd/display: Support for SET_CONFIG processing with DMUB
+    - drm/amd/display: Add DPCD writes at key points
+    - drm/amd/display: Fix DIG_HPD_SELECT for USB4 display endpoints.
+    - drm/amd/display: Add helper for blanking all dp displays
+    - drm/amd/display: Fix link training fallback logic
+    - drm/amd/display: Add debug flags for USB4 DP link training.
+    - drm/amd/display: Fix dynamic link encoder access.
+    - drm/amd/display: Fix concurrent dynamic encoder assignment
+    - drm/amd/display: Fix dynamic encoder reassignment
+    - drm/amd/display: Fix for access for ddc pin and aux engine.
+    - drm/amd/display: Deadlock/HPD Status/Crash Bug Fix
+    - drm/amd/display: Fix USB4 Aux via DMUB terminate unexpectedly
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Rewrite debian/scripts/module-check in Python
+    - [Config] update config and annotations after applying v5.15.5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 29 Nov 2021 09:25:37 +0100
+
+linux (5.15.0-12.12) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-12.12 -proposed tracker (LP: #1951810)
+
+  * Jammy update: v5.15.4 upstream stable release (LP: #1951820)
+    - string: uninline memcpy_and_pad
+    - Revert "drm: fb_helper: improve CONFIG_FB dependency"
+    - Revert "drm: fb_helper: fix CONFIG_FB dependency"
+    - KVM: Fix steal time asm constraints
+    - btrfs: introduce btrfs_is_data_reloc_root
+    - btrfs: zoned: add a dedicated data relocation block group
+    - btrfs: zoned: only allow one process to add pages to a relocation inode
+    - btrfs: zoned: use regular writes for relocation
+    - btrfs: check for relocation inodes on zoned btrfs in should_nocow
+    - btrfs: zoned: allow preallocation for relocation inodes
+    - fortify: Explicitly disable Clang support
+    - block: Add a helper to validate the block size
+    - loop: Use blk_validate_block_size() to validate block size
+    - Bluetooth: btusb: Add support for TP-Link UB500 Adapter
+    - parisc/entry: fix trace test in syscall exit path
+    - PCI/MSI: Deal with devices lying about their MSI mask capability
+    - PCI: Add MSI masking quirk for Nvidia ION AHCI
+    - perf/core: Avoid put_page() when GUP fails
+    - thermal: Fix NULL pointer dereferences in of_thermal_ functions
+    - Revert "ACPI: scan: Release PM resources blocked by unused objects"
+    - Linux 5.15.4
+
+  * Jammy update: v5.15.3 upstream stable release (LP: #1951822)
+    - xhci: Fix USB 3.1 enumeration issues by increasing roothub power-on-good
+      delay
+    - usb: xhci: Enable runtime-pm by default on AMD Yellow Carp platform
+    - Input: iforce - fix control-message timeout
+    - Input: elantench - fix misreporting trackpoint coordinates
+    - Input: i8042 - Add quirk for Fujitsu Lifebook T725
+    - libata: fix read log timeout value
+    - ocfs2: fix data corruption on truncate
+    - scsi: scsi_ioctl: Validate command size
+    - scsi: core: Avoid leaving shost->last_reset with stale value if EH does not
+      run
+    - scsi: core: Remove command size deduction from scsi_setup_scsi_cmnd()
+    - scsi: lpfc: Don't release final kref on Fport node while ABTS outstanding
+    - scsi: lpfc: Fix FCP I/O flush functionality for TMF routines
+    - scsi: qla2xxx: Fix crash in NVMe abort path
+    - scsi: qla2xxx: Fix kernel crash when accessing port_speed sysfs file
+    - scsi: qla2xxx: Fix use after free in eh_abort path
+    - ce/gf100: fix incorrect CE0 address calculation on some GPUs
+    - char: xillybus: fix msg_ep UAF in xillyusb_probe()
+    - mmc: mtk-sd: Add wait dma stop done flow
+    - mmc: dw_mmc: Dont wait for DRTO on Write RSP error
+    - exfat: fix incorrect loading of i_blocks for large files
+    - io-wq: remove worker to owner tw dependency
+    - parisc: Fix set_fixmap() on PA1.x CPUs
+    - parisc: Fix ptrace check on syscall return
+    - tpm: Check for integer overflow in tpm2_map_response_body()
+    - firmware/psci: fix application of sizeof to pointer
+    - crypto: s5p-sss - Add error handling in s5p_aes_probe()
+    - media: rkvdec: Do not override sizeimage for output format
+    - media: ite-cir: IR receiver stop working after receive overflow
+    - media: rkvdec: Support dynamic resolution changes
+    - media: ir-kbd-i2c: improve responsiveness of hauppauge zilog receivers
+    - media: v4l2-ioctl: Fix check_ext_ctrls
+    - ALSA: hda/realtek: Fix mic mute LED for the HP Spectre x360 14
+    - ALSA: hda/realtek: Add a quirk for HP OMEN 15 mute LED
+    - ALSA: hda/realtek: Add quirk for Clevo PC70HS
+    - ALSA: hda/realtek: Headset fixup for Clevo NH77HJQ
+    - ALSA: hda/realtek: Add a quirk for Acer Spin SP513-54N
+    - ALSA: hda/realtek: Add quirk for ASUS UX550VE
+    - ALSA: hda/realtek: Add quirk for HP EliteBook 840 G7 mute LED
+    - ALSA: ua101: fix division by zero at probe
+    - ALSA: 6fire: fix control and bulk message timeouts
+    - ALSA: line6: fix control and interrupt message timeouts
+    - ALSA: mixer: oss: Fix racy access to slots
+    - ALSA: mixer: fix deadlock in snd_mixer_oss_set_volume
+    - ALSA: usb-audio: Line6 HX-Stomp XL USB_ID for 48k-fixed quirk
+    - ALSA: usb-audio: Add registration quirk for JBL Quantum 400
+    - ALSA: hda: Free card instance properly at probe errors
+    - ALSA: synth: missing check for possible NULL after the call to kstrdup
+    - ALSA: pci: rme: Fix unaligned buffer addresses
+    - ALSA: PCM: Fix NULL dereference at mmap checks
+    - ALSA: timer: Fix use-after-free problem
+    - ALSA: timer: Unconditionally unlink slave instances, too
+    - Revert "ext4: enforce buffer head state assertion in ext4_da_map_blocks"
+    - ext4: fix lazy initialization next schedule time computation in more
+      granular unit
+    - ext4: ensure enough credits in ext4_ext_shift_path_extents
+    - ext4: refresh the ext4_ext_path struct after dropping i_data_sem.
+    - fuse: fix page stealing
+    - x86/sme: Use #define USE_EARLY_PGTABLE_L5 in mem_encrypt_identity.c
+    - x86/cpu: Fix migration safety with X86_BUG_NULL_SEL
+    - x86/irq: Ensure PI wakeup handler is unregistered before module unload
+    - x86/iopl: Fake iopl(3) CLI/STI usage
+    - btrfs: clear MISSING device status bit in btrfs_close_one_device
+    - btrfs: fix lost error handling when replaying directory deletes
+    - btrfs: call btrfs_check_rw_degradable only if there is a missing device
+    - KVM: x86/mmu: Drop a redundant, broken remote TLB flush
+    - KVM: VMX: Unregister posted interrupt wakeup handler on hardware unsetup
+    - KVM: PPC: Tick accounting should defer vtime accounting 'til after IRQ
+      handling
+    - ia64: kprobes: Fix to pass correct trampoline address to the handler
+    - selinux: fix race condition when computing ocontext SIDs
+    - ipmi:watchdog: Set panic count to proper value on a panic
+    - md/raid1: only allocate write behind bio for WriteMostly device
+    - hwmon: (pmbus/lm25066) Add offset coefficients
+    - regulator: s5m8767: do not use reset value as DVS voltage if GPIO DVS is
+      disabled
+    - regulator: dt-bindings: samsung,s5m8767: correct s5m8767,pmic-buck-default-
+      dvs-idx property
+    - EDAC/sb_edac: Fix top-of-high-memory value for Broadwell/Haswell
+    - mwifiex: fix division by zero in fw download path
+    - ath6kl: fix division by zero in send path
+    - ath6kl: fix control-message timeout
+    - ath10k: fix control-message timeout
+    - ath10k: fix division by zero in send path
+    - PCI: Mark Atheros QCA6174 to avoid bus reset
+    - rtl8187: fix control-message timeouts
+    - evm: mark evm_fixmode as __ro_after_init
+    - ifb: Depend on netfilter alternatively to tc
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Studio
+    - mt76: mt7615: fix skb use-after-free on mac reset
+    - HID: surface-hid: Use correct event registry for managing HID events
+    - HID: surface-hid: Allow driver matching for target ID 1 devices
+    - wcn36xx: Fix HT40 capability for 2Ghz band
+    - wcn36xx: Fix tx_status mechanism
+    - wcn36xx: Fix (QoS) null data frame bitrate/modulation
+    - PM: sleep: Do not let "syscore" devices runtime-suspend during system
+      transitions
+    - mwifiex: Read a PCI register after writing the TX ring write pointer
+    - mwifiex: Try waking the firmware until we get an interrupt
+    - libata: fix checking of DMA state
+    - dma-buf: fix and rework dma_buf_poll v7
+    - wcn36xx: handle connection loss indication
+    - rsi: fix occasional initialisation failure with BT coex
+    - rsi: fix key enabled check causing unwanted encryption for vap_id > 0
+    - rsi: fix rate mask set leading to P2P failure
+    - rsi: Fix module dev_oper_mode parameter description
+    - perf/x86/intel/uncore: Support extra IMC channel on Ice Lake server
+    - perf/x86/intel/uncore: Fix invalid unit check
+    - perf/x86/intel/uncore: Fix Intel ICX IIO event constraints
+    - RDMA/qedr: Fix NULL deref for query_qp on the GSI QP
+    - ASoC: tegra: Set default card name for Trimslice
+    - ASoC: tegra: Restore AC97 support
+    - signal: Remove the bogus sigkill_pending in ptrace_stop
+    - memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode
+    - signal/mips: Update (_save|_restore)_fp_context to fail with -EFAULT
+    - soc: samsung: exynos-pmu: Fix compilation when nothing selects
+      CONFIG_MFD_CORE
+    - soc: fsl: dpio: replace smp_processor_id with raw_smp_processor_id
+    - soc: fsl: dpio: use the combined functions to protect critical zone
+    - mtd: rawnand: socrates: Keep the driver compatible with on-die ECC engines
+    - mctp: handle the struct sockaddr_mctp padding fields
+    - power: supply: max17042_battery: Prevent int underflow in set_soc_threshold
+    - power: supply: max17042_battery: use VFSOC for capacity when no rsns
+    - iio: core: fix double free in iio_device_unregister_sysfs()
+    - iio: core: check return value when calling dev_set_name()
+    - KVM: arm64: Extract ESR_ELx.EC only
+    - KVM: x86: Fix recording of guest steal time / preempted status
+    - KVM: x86: Add helper to consolidate core logic of SET_CPUID{2} flows
+    - KVM: nVMX: Query current VMCS when determining if MSR bitmaps are in use
+    - KVM: nVMX: Handle dynamic MSR intercept toggling
+    - can: peak_usb: always ask for BERR reporting for PCAN-USB devices
+    - can: mcp251xfd: mcp251xfd_irq(): add missing
+      can_rx_offload_threaded_irq_finish() in case of bus off
+    - can: j1939: j1939_tp_cmd_recv(): ignore abort message in the BAM transport
+    - can: j1939: j1939_can_recv(): ignore messages with invalid source address
+    - can: j1939: j1939_tp_cmd_recv(): check the dst address of TP.CM_BAM
+    - iio: adc: tsc2046: fix scan interval warning
+    - powerpc/85xx: Fix oops when mpc85xx_smp_guts_ids node cannot be found
+    - io_uring: honour zeroes as io-wq worker limits
+    - ring-buffer: Protect ring_buffer_reset() from reentrancy
+    - serial: core: Fix initializing and restoring termios speed
+    - ifb: fix building without CONFIG_NET_CLS_ACT
+    - xen/balloon: add late_initcall_sync() for initial ballooning done
+    - ovl: fix use after free in struct ovl_aio_req
+    - ovl: fix filattr copy-up failure
+    - PCI: pci-bridge-emul: Fix emulation of W1C bits
+    - PCI: cadence: Add cdns_plat_pcie_probe() missing return
+    - cxl/pci: Fix NULL vs ERR_PTR confusion
+    - PCI: aardvark: Do not clear status bits of masked interrupts
+    - PCI: aardvark: Fix checking for link up via LTSSM state
+    - PCI: aardvark: Do not unmask unused interrupts
+    - PCI: aardvark: Fix reporting Data Link Layer Link Active
+    - PCI: aardvark: Fix configuring Reference clock
+    - PCI: aardvark: Fix return value of MSI domain .alloc() method
+    - PCI: aardvark: Read all 16-bits from PCIE_MSI_PAYLOAD_REG
+    - PCI: aardvark: Fix support for bus mastering and PCI_COMMAND on emulated
+      bridge
+    - PCI: aardvark: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
+    - PCI: aardvark: Set PCI Bridge Class Code to PCI Bridge
+    - PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge
+    - quota: check block number when reading the block in quota file
+    - quota: correct error number in free_dqentry()
+    - cifs: To match file servers, make sure the server hostname matches
+    - cifs: set a minimum of 120s for next dns resolution
+    - mfd: simple-mfd-i2c: Select MFD_CORE to fix build error
+    - pinctrl: core: fix possible memory leak in pinctrl_enable()
+    - coresight: cti: Correct the parameter for pm_runtime_put
+    - coresight: trbe: Fix incorrect access of the sink specific data
+    - coresight: trbe: Defer the probe on offline CPUs
+    - iio: buffer: check return value of kstrdup_const()
+    - iio: buffer: Fix memory leak in iio_buffers_alloc_sysfs_and_mask()
+    - iio: buffer: Fix memory leak in __iio_buffer_alloc_sysfs_and_mask()
+    - iio: buffer: Fix memory leak in iio_buffer_register_legacy_sysfs_groups()
+    - drivers: iio: dac: ad5766: Fix dt property name
+    - iio: dac: ad5446: Fix ad5622_write() return value
+    - iio: ad5770r: make devicetree property reading consistent
+    - Documentation:devicetree:bindings:iio:dac: Fix val
+    - USB: serial: keyspan: fix memleak on probe errors
+    - serial: 8250: fix racy uartclk update
+    - ksmbd: set unique value to volume serial field in FS_VOLUME_INFORMATION
+    - io-wq: serialize hash clear with wakeup
+    - serial: 8250: Fix reporting real baudrate value in c_ospeed field
+    - Revert "serial: 8250: Fix reporting real baudrate value in c_ospeed field"
+    - most: fix control-message timeouts
+    - USB: iowarrior: fix control-message timeouts
+    - USB: chipidea: fix interrupt deadlock
+    - power: supply: max17042_battery: Clear status bits in interrupt handler
+    - component: do not leave master devres group open after bind
+    - dma-buf: WARN on dmabuf release with pending attachments
+    - drm: panel-orientation-quirks: Update the Lenovo Ideapad D330 quirk (v2)
+    - drm: panel-orientation-quirks: Add quirk for KD Kurio Smart C15200 2-in-1
+    - drm: panel-orientation-quirks: Add quirk for the Samsung Galaxy Book 10.6
+    - Bluetooth: sco: Fix lock_sock() blockage by memcpy_from_msg()
+    - Bluetooth: fix use-after-free error in lock_sock_nested()
+    - Bluetooth: call sock_hold earlier in sco_conn_del
+    - drm/panel-orientation-quirks: add Valve Steam Deck
+    - rcutorture: Avoid problematic critical section nesting on PREEMPT_RT
+    - platform/x86: wmi: do not fail if disabling fails
+    - drm/amdgpu: move iommu_resume before ip init/resume
+    - MIPS: lantiq: dma: add small delay after reset
+    - MIPS: lantiq: dma: reset correct number of channel
+    - locking/lockdep: Avoid RCU-induced noinstr fail
+    - net: sched: update default qdisc visibility after Tx queue cnt changes
+    - rcu-tasks: Move RTGS_WAIT_CBS to beginning of rcu_tasks_kthread() loop
+    - smackfs: Fix use-after-free in netlbl_catmap_walk()
+    - ath11k: Align bss_chan_info structure with firmware
+    - crypto: aesni - check walk.nbytes instead of err
+    - x86/mm/64: Improve stack overflow warnings
+    - x86: Increase exception stack sizes
+    - mwifiex: Run SET_BSS_MODE when changing from P2P to STATION vif-type
+    - mwifiex: Properly initialize private structure on interface type changes
+    - spi: Check we have a spi_device_id for each DT compatible
+    - fscrypt: allow 256-bit master keys with AES-256-XTS
+    - drm/amdgpu: Fix MMIO access page fault
+    - drm/amd/display: Fix null pointer dereference for encoders
+    - selftests: net: fib_nexthops: Wait before checking reported idle time
+    - ath11k: Avoid reg rules update during firmware recovery
+    - ath11k: add handler for scan event WMI_SCAN_EVENT_DEQUEUED
+    - ath11k: Change DMA_FROM_DEVICE to DMA_TO_DEVICE when map reinjected packets
+    - ath10k: high latency fixes for beacon buffer
+    - octeontx2-pf: Enable promisc/allmulti match MCAM entries.
+    - media: mt9p031: Fix corrupted frame after restarting stream
+    - media: netup_unidvb: handle interrupt properly according to the firmware
+    - media: atomisp: Fix error handling in probe
+    - media: stm32: Potential NULL pointer dereference in dcmi_irq_thread()
+    - media: uvcvideo: Set capability in s_param
+    - media: uvcvideo: Return -EIO for control errors
+    - media: uvcvideo: Set unique vdev name based in type
+    - media: vidtv: Fix memory leak in remove
+    - media: s5p-mfc: fix possible null-pointer dereference in s5p_mfc_probe()
+    - media: s5p-mfc: Add checking to s5p_mfc_probe().
+    - media: videobuf2: rework vb2_mem_ops API
+    - media: imx: set a media_device bus_info string
+    - media: rcar-vin: Use user provided buffers when starting
+    - media: mceusb: return without resubmitting URB in case of -EPROTO error.
+    - ia64: don't do IA64_CMPXCHG_DEBUG without CONFIG_PRINTK
+    - rtw88: fix RX clock gate setting while fifo dump
+    - brcmfmac: Add DMI nvram filename quirk for Cyberbook T116 tablet
+    - media: rcar-csi2: Add checking to rcsi2_start_receiver()
+    - ipmi: Disable some operations during a panic
+    - fs/proc/uptime.c: Fix idle time reporting in /proc/uptime
+    - kselftests/sched: cleanup the child processes
+    - ACPICA: Avoid evaluating methods too early during system resume
+    - cpufreq: Make policy min/max hard requirements
+    - ice: Move devlink port to PF/VF struct
+    - media: imx-jpeg: Fix possible null pointer dereference
+    - media: ipu3-imgu: imgu_fmt: Handle properly try
+    - media: ipu3-imgu: VIDIOC_QUERYCAP: Fix bus_info
+    - media: usb: dvd-usb: fix uninit-value bug in dibusb_read_eeprom_byte()
+    - net-sysfs: try not to restart the syscall if it will fail eventually
+    - drm/amdkfd: rm BO resv on validation to avoid deadlock
+    - tracefs: Have tracefs directories not set OTH permission bits by default
+    - tracing: Disable "other" permission bits in the tracefs files
+    - ath: dfs_pattern_detector: Fix possible null-pointer dereference in
+      channel_detector_create()
+    - KVM: arm64: Propagate errors from __pkvm_prot_finalize hypercall
+    - mmc: moxart: Fix reference count leaks in moxart_probe
+    - iov_iter: Fix iov_iter_get_pages{,_alloc} page fault return value
+    - ACPI: battery: Accept charges over the design capacity as full
+    - ACPI: scan: Release PM resources blocked by unused objects
+    - drm/amd/display: fix null pointer deref when plugging in display
+    - drm/amdkfd: fix resume error when iommu disabled in Picasso
+    - net: phy: micrel: make *-skew-ps check more lenient
+    - leaking_addresses: Always print a trailing newline
+    - thermal/core: Fix null pointer dereference in thermal_release()
+    - drm/msm: prevent NULL dereference in msm_gpu_crashstate_capture()
+    - thermal/drivers/tsens: Add timeout to get_temp_tsens_valid
+    - block: bump max plugged deferred size from 16 to 32
+    - floppy: fix calling platform_device_unregister() on invalid drives
+    - md: update superblock after changing rdev flags in state_store
+    - memstick: r592: Fix a UAF bug when removing the driver
+    - locking/rwsem: Disable preemption for spinning region
+    - lib/xz: Avoid overlapping memcpy() with invalid input with in-place
+      decompression
+    - lib/xz: Validate the value before assigning it to an enum variable
+    - workqueue: make sysfs of unbound kworker cpumask more clever
+    - tracing/cfi: Fix cmp_entries_* functions signature mismatch
+    - mt76: mt7915: fix an off-by-one bound check
+    - mwl8k: Fix use-after-free in mwl8k_fw_state_machine()
+    - iwlwifi: change all JnP to NO-160 configuration
+    - block: remove inaccurate requeue check
+    - media: allegro: ignore interrupt if mailbox is not initialized
+    - drm/amdgpu/pm: properly handle sclk for profiling modes on vangogh
+    - nvmet: fix use-after-free when a port is removed
+    - nvmet-rdma: fix use-after-free when a port is removed
+    - nvmet-tcp: fix use-after-free when a port is removed
+    - nvme: drop scan_lock and always kick requeue list when removing namespaces
+    - samples/bpf: Fix application of sizeof to pointer
+    - arm64: vdso32: suppress error message for 'make mrproper'
+    - PM: hibernate: Get block device exclusively in swsusp_check()
+    - selftests: kvm: fix mismatched fclose() after popen()
+    - selftests/bpf: Fix perf_buffer test on system with offline cpus
+    - iwlwifi: mvm: disable RX-diversity in powersave
+    - smackfs: use __GFP_NOFAIL for smk_cipso_doi()
+    - ARM: clang: Do not rely on lr register for stacktrace
+    - gre/sit: Don't generate link-local addr if addr_gen_mode is
+      IN6_ADDR_GEN_MODE_NONE
+    - can: bittiming: can_fixup_bittiming(): change type of tseg1 and alltseg to
+      unsigned int
+    - gfs2: Cancel remote delete work asynchronously
+    - gfs2: Fix glock_hash_walk bugs
+    - ARM: 9136/1: ARMv7-M uses BE-8, not BE-32
+    - tools/latency-collector: Use correct size when writing queue_full_warning
+    - vrf: run conntrack only in context of lower/physdev for locally generated
+      packets
+    - net: annotate data-race in neigh_output()
+    - ACPI: AC: Quirk GK45 to skip reading _PSR
+    - ACPI: resources: Add one more Medion model in IRQ override quirk
+    - btrfs: reflink: initialize return value to 0 in btrfs_extent_same()
+    - btrfs: do not take the uuid_mutex in btrfs_rm_device
+    - spi: bcm-qspi: Fix missing clk_disable_unprepare() on error in
+      bcm_qspi_probe()
+    - wcn36xx: Correct band/freq reporting on RX
+    - wcn36xx: Fix packet drop on resume
+    - Revert "wcn36xx: Enable firmware link monitoring"
+    - ftrace: do CPU checking after preemption disabled
+    - inet: remove races in inet{6}_getname()
+    - x86/hyperv: Protect set_hv_tscchange_cb() against getting preempted
+    - drm/amd/display: dcn20_resource_construct reduce scope of FPU enabled
+    - perf/x86/intel: Fix ICL/SPR INST_RETIRED.PREC_DIST encodings
+    - parisc: fix warning in flush_tlb_all
+    - task_stack: Fix end_of_stack() for architectures with upwards-growing stack
+    - erofs: don't trigger WARN() when decompression fails
+    - parisc/unwind: fix unwinder when CONFIG_64BIT is enabled
+    - parisc/kgdb: add kgdb_roundup() to make kgdb work with idle polling
+    - netfilter: conntrack: set on IPS_ASSURED if flows enters internal stream
+      state
+    - selftests/bpf: Fix strobemeta selftest regression
+    - fbdev/efifb: Release PCI device's runtime PM ref during FB destroy
+    - drm/bridge: anx7625: Propagate errors from sp_tx_rst_aux()
+    - perf/x86/intel/uncore: Fix Intel SPR CHA event constraints
+    - perf/x86/intel/uncore: Fix Intel SPR IIO event constraints
+    - perf/x86/intel/uncore: Fix Intel SPR M2PCIE event constraints
+    - perf/x86/intel/uncore: Fix Intel SPR M3UPI event constraints
+    - drm/bridge: it66121: Initialize {device,vendor}_ids
+    - drm/bridge: it66121: Wait for next bridge to be probed
+    - Bluetooth: fix init and cleanup of sco_conn.timeout_work
+    - libbpf: Don't crash on object files with no symbol tables
+    - Bluetooth: hci_uart: fix GPF in h5_recv
+    - rcu: Fix existing exp request check in sync_sched_exp_online_cleanup()
+    - MIPS: lantiq: dma: fix burst length for DEU
+    - x86/xen: Mark cpu_bringup_and_idle() as dead_end_function
+    - objtool: Handle __sanitize_cov*() tail calls
+    - net/mlx5: Publish and unpublish all devlink parameters at once
+    - drm/v3d: fix wait for TMU write combiner flush
+    - crypto: sm4 - Do not change section of ck and sbox
+    - virtio-gpu: fix possible memory allocation failure
+    - lockdep: Let lock_is_held_type() detect recursive read as read
+    - net: net_namespace: Fix undefined member in key_remove_domain()
+    - net: phylink: don't call netif_carrier_off() with NULL netdev
+    - drm: bridge: it66121: Fix return value it66121_probe
+    - spi: Fixed division by zero warning
+    - cgroup: Make rebind_subsystems() disable v2 controllers all at once
+    - wcn36xx: Fix Antenna Diversity Switching
+    - wilc1000: fix possible memory leak in cfg_scan_result()
+    - Bluetooth: btmtkuart: fix a memleak in mtk_hci_wmt_sync
+    - drm/amdgpu: Fix crash on device remove/driver unload
+    - drm/amd/display: Pass display_pipe_params_st as const in DML
+    - drm/amdgpu: move amdgpu_virt_release_full_gpu to fini_early stage
+    - crypto: caam - disable pkc for non-E SoCs
+    - crypto: qat - power up 4xxx device
+    - Bluetooth: hci_h5: Fix (runtime)suspend issues on RTL8723BS HCIs
+    - bnxt_en: Check devlink allocation and registration status
+    - qed: Don't ignore devlink allocation failures
+    - rxrpc: Fix _usecs_to_jiffies() by using usecs_to_jiffies()
+    - mptcp: do not shrink snd_nxt when recovering
+    - fortify: Fix dropped strcpy() compile-time write overflow check
+    - mac80211: twt: don't use potentially unaligned pointer
+    - cfg80211: always free wiphy specific regdomain
+    - net/mlx5: Accept devlink user input after driver initialization complete
+    - net: dsa: rtl8366rb: Fix off-by-one bug
+    - net: dsa: rtl8366: Fix a bug in deleting VLANs
+    - bpf/tests: Fix error in tail call limit tests
+    - ath11k: fix some sleeping in atomic bugs
+    - ath11k: Avoid race during regd updates
+    - ath11k: fix packet drops due to incorrect 6 GHz freq value in rx status
+    - ath11k: Fix memory leak in ath11k_qmi_driver_event_work
+    - gve: DQO: avoid unused variable warnings
+    - ath10k: Fix missing frame timestamp for beacon/probe-resp
+    - ath10k: sdio: Add missing BH locking around napi_schdule()
+    - drm/ttm: stop calling tt_swapin in vm_access
+    - arm64: mm: update max_pfn after memory hotplug
+    - drm/amdgpu: fix warning for overflow check
+    - libbpf: Fix skel_internal.h to set errno on loader retval < 0
+    - media: em28xx: add missing em28xx_close_extension
+    - media: meson-ge2d: Fix rotation parameter changes detection in
+      'ge2d_s_ctrl()'
+    - media: cxd2880-spi: Fix a null pointer dereference on error handling path
+    - media: ttusb-dec: avoid release of non-acquired mutex
+    - media: dvb-usb: fix ununit-value in az6027_rc_query
+    - media: imx258: Fix getting clock frequency
+    - media: v4l2-ioctl: S_CTRL output the right value
+    - media: mtk-vcodec: venc: fix return value when start_streaming fails
+    - media: TDA1997x: handle short reads of hdmi info frame.
+    - media: mtk-vpu: Fix a resource leak in the error handling path of
+      'mtk_vpu_probe()'
+    - media: imx-jpeg: Fix the error handling path of 'mxc_jpeg_probe()'
+    - media: i2c: ths8200 needs V4L2_ASYNC
+    - media: sun6i-csi: Allow the video device to be open multiple times
+    - media: radio-wl1273: Avoid card name truncation
+    - media: si470x: Avoid card name truncation
+    - media: tm6000: Avoid card name truncation
+    - media: cx23885: Fix snd_card_free call on null card pointer
+    - media: atmel: fix the ispck initialization
+    - scs: Release kasan vmalloc poison in scs_free process
+    - kprobes: Do not use local variable when creating debugfs file
+    - crypto: ecc - fix CRYPTO_DEFAULT_RNG dependency
+    - drm: fb_helper: fix CONFIG_FB dependency
+    - cpuidle: Fix kobject memory leaks in error paths
+    - media: em28xx: Don't use ops->suspend if it is NULL
+    - ath10k: Don't always treat modem stop events as crashes
+    - ath9k: Fix potential interrupt storm on queue reset
+    - PM: EM: Fix inefficient states detection
+    - x86/insn: Use get_unaligned() instead of memcpy()
+    - EDAC/amd64: Handle three rank interleaving mode
+    - rcu: Always inline rcu_dynticks_task*_{enter,exit}()
+    - rcu: Fix rcu_dynticks_curr_cpu_in_eqs() vs noinstr
+    - netfilter: nft_dynset: relax superfluous check on set updates
+    - media: venus: fix vpp frequency calculation for decoder
+    - media: dvb-frontends: mn88443x: Handle errors of clk_prepare_enable()
+    - crypto: ccree - avoid out-of-range warnings from clang
+    - crypto: qat - detect PFVF collision after ACK
+    - crypto: qat - disregard spurious PFVF interrupts
+    - hwrng: mtk - Force runtime pm ops for sleep ops
+    - ima: fix deadlock when traversing "ima_default_rules".
+    - b43legacy: fix a lower bounds test
+    - b43: fix a lower bounds test
+    - gve: Recover from queue stall due to missed IRQ
+    - gve: Track RX buffer allocation failures
+    - mmc: sdhci-omap: Fix NULL pointer exception if regulator is not configured
+    - mmc: sdhci-omap: Fix context restore
+    - memstick: avoid out-of-range warning
+    - memstick: jmb38x_ms: use appropriate free function in jmb38x_ms_alloc_host()
+    - net, neigh: Fix NTF_EXT_LEARNED in combination with NTF_USE
+    - hwmon: Fix possible memleak in __hwmon_device_register()
+    - hwmon: (pmbus/lm25066) Let compiler determine outer dimension of
+      lm25066_coeff
+    - ath10k: fix max antenna gain unit
+    - kernel/sched: Fix sched_fork() access an invalid sched_task_group
+    - net: fealnx: fix build for UML
+    - net: intel: igc_ptp: fix build for UML
+    - net: tulip: winbond-840: fix build for UML
+    - tcp: switch orphan_count to bare per-cpu counters
+    - crypto: octeontx2 - set assoclen in aead_do_fallback()
+    - thermal/core: fix a UAF bug in __thermal_cooling_device_register()
+    - drm/msm/dsi: do not enable irq handler before powering up the host
+    - drm/msm: Fix potential Oops in a6xx_gmu_rpmh_init()
+    - drm/msm: potential error pointer dereference in init()
+    - drm/msm: unlock on error in get_sched_entity()
+    - drm/msm: fix potential NULL dereference in cleanup
+    - drm/msm: uninitialized variable in msm_gem_import()
+    - net: stream: don't purge sk_error_queue in sk_stream_kill_queues()
+    - thermal/drivers/qcom/lmh: make QCOM_LMH depends on QCOM_SCM
+    - mailbox: Remove WARN_ON for async_cb.cb in cmdq_exec_done
+    - media: ivtv: fix build for UML
+    - media: ir_toy: assignment to be16 should be of correct type
+    - mmc: mxs-mmc: disable regulator on error and in the remove function
+    - io-wq: Remove duplicate code in io_workqueue_create()
+    - block: ataflop: fix breakage introduced at blk-mq refactoring
+    - platform/x86: thinkpad_acpi: Fix bitwise vs. logical warning
+    - mailbox: mtk-cmdq: Validate alias_id on probe
+    - mailbox: mtk-cmdq: Fix local clock ID usage
+    - ACPI: PM: Turn off unused wakeup power resources
+    - ACPI: PM: Fix sharing of wakeup power resources
+    - drm/amdkfd: Fix an inappropriate error handling in allloc memory of gpu
+    - mt76: mt7921: fix endianness in mt7921_mcu_tx_done_event
+    - mt76: mt7915: fix endianness warning in mt7915_mac_add_txs_skb
+    - mt76: mt7921: fix endianness warning in mt7921_update_txs
+    - mt76: mt7615: fix endianness warning in mt7615_mac_write_txwi
+    - mt76: mt7915: fix info leak in mt7915_mcu_set_pre_cal()
+    - mt76: connac: fix mt76_connac_gtk_rekey_tlv usage
+    - mt76: fix build error implicit enumeration conversion
+    - mt76: mt7921: fix survey-dump reporting
+    - mt76: mt76x02: fix endianness warnings in mt76x02_mac.c
+    - mt76: mt7921: Fix out of order process by invalid event pkt
+    - mt76: mt7915: fix potential overflow of eeprom page index
+    - mt76: mt7915: fix bit fields for HT rate idx
+    - mt76: mt7921: fix dma hang in rmmod
+    - mt76: connac: fix GTK rekey offload failure on WPA mixed mode
+    - mt76: overwrite default reg_ops if necessary
+    - mt76: mt7921: report HE MU radiotap
+    - mt76: mt7921: fix firmware usage of RA info using legacy rates
+    - mt76: mt7921: fix kernel warning from cfg80211_calculate_bitrate
+    - mt76: mt7921: always wake device if necessary in debugfs
+    - mt76: mt7915: fix hwmon temp sensor mem use-after-free
+    - mt76: mt7615: fix hwmon temp sensor mem use-after-free
+    - mt76: mt7915: fix possible infinite loop release semaphore
+    - mt76: mt7921: fix retrying release semaphore without end
+    - mt76: mt7615: fix monitor mode tear down crash
+    - mt76: connac: fix possible NULL pointer dereference in
+      mt76_connac_get_phy_mode_v2
+    - mt76: mt7915: fix sta_rec_wtbl tag len
+    - mt76: mt7915: fix muar_idx in mt7915_mcu_alloc_sta_req()
+    - rsi: stop thread firstly in rsi_91x_init() error handling
+    - mwifiex: Send DELBA requests according to spec
+    - iwlwifi: mvm: reset PM state on unsuccessful resume
+    - iwlwifi: pnvm: don't kmemdup() more than we have
+    - iwlwifi: pnvm: read EFI data only if long enough
+    - net: enetc: unmap DMA in enetc_send_cmd()
+    - phy: micrel: ksz8041nl: do not use power down mode
+    - nbd: Fix use-after-free in pid_show
+    - nvme-rdma: fix error code in nvme_rdma_setup_ctrl
+    - PM: hibernate: fix sparse warnings
+    - clocksource/drivers/timer-ti-dm: Select TIMER_OF
+    - x86/sev: Fix stack type check in vc_switch_off_ist()
+    - drm/msm: Fix potential NULL dereference in DPU SSPP
+    - drm/msm/dsi: fix wrong type in msm_dsi_host
+    - crypto: tcrypt - fix skcipher multi-buffer tests for 1420B blocks
+    - smackfs: use netlbl_cfg_cipsov4_del() for deleting cipso_v4_doi
+    - KVM: selftests: Fix nested SVM tests when built with clang
+    - libbpf: Fix memory leak in btf__dedup()
+    - bpftool: Avoid leaking the JSON writer prepared for program metadata
+    - libbpf: Fix overflow in BTF sanity checks
+    - libbpf: Fix BTF header parsing checks
+    - mt76: mt7615: mt7622: fix ibss and meshpoint
+    - s390/gmap: validate VMA in __gmap_zap()
+    - s390/gmap: don't unconditionally call pte_unmap_unlock() in __gmap_zap()
+    - s390/mm: validate VMA in PGSTE manipulation functions
+    - s390/mm: fix VMA and page table handling code in storage key handling
+      functions
+    - s390/uv: fully validate the VMA before calling follow_page()
+    - KVM: s390: pv: avoid double free of sida page
+    - KVM: s390: pv: avoid stalls for kvm_s390_pv_init_vm
+    - irq: mips: avoid nested irq_enter()
+    - net: dsa: avoid refcount warnings when ->port_{fdb,mdb}_del returns error
+    - ARM: 9142/1: kasan: work around LPAE build warning
+    - ath10k: fix module load regression with iram-recovery feature
+    - block: ataflop: more blk-mq refactoring fixes
+    - blk-cgroup: synchronize blkg creation against policy deactivation
+    - libbpf: Fix off-by-one bug in bpf_core_apply_relo()
+    - tpm: fix Atmel TPM crash caused by too frequent queries
+    - tpm_tis_spi: Add missing SPI ID
+    - libbpf: Fix endianness detection in BPF_CORE_READ_BITFIELD_PROBED()
+    - tcp: don't free a FIN sk_buff in tcp_remove_empty_skb()
+    - tracing: Fix missing trace_boot_init_histograms kstrdup NULL checks
+    - cpufreq: intel_pstate: Fix cpu->pstate.turbo_freq initialization
+    - spi: spi-rpc-if: Check return value of rpcif_sw_init()
+    - samples/kretprobes: Fix return value if register_kretprobe() failed
+    - KVM: s390: Fix handle_sske page fault handling
+    - libertas_tf: Fix possible memory leak in probe and disconnect
+    - libertas: Fix possible memory leak in probe and disconnect
+    - wcn36xx: add proper DMA memory barriers in rx path
+    - wcn36xx: Fix discarded frames due to wrong sequence number
+    - bpf: Avoid races in __bpf_prog_run() for 32bit arches
+    - bpf: Fixes possible race in update_prog_stats() for 32bit arches
+    - wcn36xx: Channel list update before hardware scan
+    - drm/amdgpu: fix a potential memory leak in amdgpu_device_fini_sw()
+    - drm/amdgpu/gmc6: fix DMA mask from 44 to 40 bits
+    - selftests/bpf: Fix fd cleanup in sk_lookup test
+    - selftests/bpf: Fix memory leak in test_ima
+    - sctp: allow IP fragmentation when PLPMTUD enters Error state
+    - sctp: reset probe_timer in sctp_transport_pl_update
+    - sctp: subtract sctphdr len in sctp_transport_pl_hlen
+    - sctp: return true only for pathmtu update in sctp_transport_pl_toobig
+    - net: amd-xgbe: Toggle PLL settings during rate change
+    - ipmi: kcs_bmc: Fix a memory leak in the error handling path of
+      'kcs_bmc_serio_add_device()'
+    - nfp: fix NULL pointer access when scheduling dim work
+    - nfp: fix potential deadlock when canceling dim work
+    - net: phylink: avoid mvneta warning when setting pause parameters
+    - net: bridge: fix uninitialized variables when BRIDGE_CFM is disabled
+    - selftests: net: bridge: update IGMP/MLD membership interval value
+    - crypto: pcrypt - Delay write to padata->info
+    - selftests/bpf: Fix fclose/pclose mismatch in test_progs
+    - udp6: allow SO_MARK ctrl msg to affect routing
+    - ibmvnic: don't stop queue in xmit
+    - ibmvnic: Process crqs after enabling interrupts
+    - ibmvnic: delay complete()
+    - selftests: mptcp: fix proto type in link_failure tests
+    - skmsg: Lose offset info in sk_psock_skb_ingress
+    - cgroup: Fix rootcg cpu.stat guest double counting
+    - bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
+    - bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
+    - of: unittest: fix EXPECT text for gpio hog errors
+    - cpufreq: Fix parameter in parse_perf_domain()
+    - staging: r8188eu: fix memory leak in rtw_set_key
+    - arm64: dts: meson: sm1: add Ethernet PHY reset line for ODROID-C4/HC4
+    - iio: st_sensors: disable regulators after device unregistration
+    - RDMA/rxe: Fix wrong port_cap_flags
+    - ARM: dts: BCM5301X: Fix memory nodes names
+    - arm64: dts: broadcom: bcm4908: Fix UART clock name
+    - clk: mvebu: ap-cpu-clk: Fix a memory leak in error handling paths
+    - scsi: pm80xx: Fix lockup in outbound queue management
+    - scsi: qla2xxx: edif: Use link event to wake up app
+    - scsi: lpfc: Fix NVMe I/O failover to non-optimized path
+    - ARM: s3c: irq-s3c24xx: Fix return value check for s3c24xx_init_intc()
+    - arm64: dts: rockchip: Fix GPU register width for RK3328
+    - ARM: dts: qcom: msm8974: Add xo_board reference clock to DSI0 PHY
+    - RDMA/bnxt_re: Fix query SRQ failure
+    - arm64: dts: ti: k3-j721e-main: Fix "max-virtual-functions" in PCIe EP nodes
+    - arm64: dts: ti: k3-j721e-main: Fix "bus-range" upto 256 bus number for PCIe
+    - arm64: dts: ti: j7200-main: Fix "vendor-id"/"device-id" properties of pcie
+      node
+    - arm64: dts: ti: j7200-main: Fix "bus-range" upto 256 bus number for PCIe
+    - arm64: dts: meson-g12a: Fix the pwm regulator supply properties
+    - arm64: dts: meson-g12b: Fix the pwm regulator supply properties
+    - arm64: dts: meson-sm1: Fix the pwm regulator supply properties
+    - bus: ti-sysc: Fix timekeeping_suspended warning on resume
+    - ARM: dts: at91: tse850: the emac<->phy interface is rmii
+    - arm64: dts: qcom: sc7180: Base dynamic CPU power coefficients in reality
+    - soc: qcom: llcc: Disable MMUHWT retention
+    - arm64: dts: qcom: sc7280: fix display port phy reg property
+    - scsi: dc395: Fix error case unwinding
+    - MIPS: loongson64: make CPU_LOONGSON64 depends on MIPS_FP_SUPPORT
+    - JFS: fix memleak in jfs_mount
+    - pinctrl: renesas: rzg2l: Fix missing port register 21h
+    - ASoC: wcd9335: Use correct version to initialize Class H
+    - arm64: dts: qcom: msm8916: Fix Secondary MI2S bit clock
+    - arm64: dts: renesas: beacon: Fix Ethernet PHY mode
+    - iommu/mediatek: Fix out-of-range warning with clang
+    - arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000
+    - iommu/dma: Fix sync_sg with swiotlb
+    - iommu/dma: Fix arch_sync_dma for map
+    - ALSA: hda: Reduce udelay() at SKL+ position reporting
+    - ALSA: hda: Use position buffer for SKL+ again
+    - ALSA: usb-audio: Fix possible race at sync of urb completions
+    - soundwire: debugfs: use controller id and link_id for debugfs
+    - power: reset: at91-reset: check properly the return value of devm_of_iomap
+    - scsi: ufs: core: Fix ufshcd_probe_hba() prototype to match the definition
+    - scsi: ufs: core: Stop clearing UNIT ATTENTIONS
+    - scsi: megaraid_sas: Fix concurrent access to ISR between IRQ polling and
+      real interrupt
+    - scsi: pm80xx: Fix misleading log statement in pm8001_mpi_get_nvmd_resp()
+    - driver core: Fix possible memory leak in device_link_add()
+    - arm: dts: omap3-gta04a4: accelerometer irq fix
+    - ASoC: SOF: topology: do not power down primary core during topology removal
+    - iio: st_pressure_spi: Add missing entries SPI to device ID table
+    - soc/tegra: Fix an error handling path in tegra_powergate_power_up()
+    - memory: fsl_ifc: fix leak of irq and nand_irq in fsl_ifc_ctrl_probe
+    - clk: at91: check pmc node status before registering syscore ops
+    - powerpc/mem: Fix arch/powerpc/mm/mem.c:53:12: error: no previous prototype
+      for 'create_section_mapping'
+    - video: fbdev: chipsfb: use memset_io() instead of memset()
+    - powerpc: fix unbalanced node refcount in check_kvm_guest()
+    - powerpc/paravirt: correct preempt debug splat in vcpu_is_preempted()
+    - serial: 8250_dw: Drop wrong use of ACPI_PTR()
+    - usb: gadget: hid: fix error code in do_config()
+    - power: supply: rt5033_battery: Change voltage values to µV
+    - power: supply: max17040: fix null-ptr-deref in max17040_probe()
+    - scsi: csiostor: Uninitialized data in csio_ln_vnp_read_cbfn()
+    - RDMA/mlx4: Return missed an error if device doesn't support steering
+    - usb: musb: select GENERIC_PHY instead of depending on it
+    - staging: most: dim2: do not double-register the same device
+    - staging: ks7010: select CRYPTO_HASH/CRYPTO_MICHAEL_MIC
+    - RDMA/core: Set sgtable nents when using ib_dma_virt_map_sg()
+    - dyndbg: make dyndbg a known cli param
+    - powerpc/perf: Fix cycles/instructions as PM_CYC/PM_INST_CMPL in power10
+    - pinctrl: renesas: checker: Fix off-by-one bug in drive register check
+    - ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
+    - ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
+    - ARM: dts: stm32: fix SAI sub nodes register range
+    - ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
+    - ASoC: cs42l42: Always configure both ASP TX channels
+    - ASoC: cs42l42: Correct some register default values
+    - ASoC: cs42l42: Defer probe if request_threaded_irq() returns EPROBE_DEFER
+    - soc: qcom: rpmhpd: Make power_on actually enable the domain
+    - soc: qcom: socinfo: add two missing PMIC IDs
+    - iio: buffer: Fix double-free in iio_buffers_alloc_sysfs_and_mask()
+    - usb: typec: STUSB160X should select REGMAP_I2C
+    - iio: adis: do not disabe IRQs in 'adis_init()'
+    - soundwire: bus: stop dereferencing invalid slave pointer
+    - scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
+    - scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
+    - serial: imx: fix detach/attach of serial console
+    - usb: dwc2: drd: fix dwc2_force_mode call in dwc2_ovr_init
+    - usb: dwc2: drd: fix dwc2_drd_role_sw_set when clock could be disabled
+    - usb: dwc2: drd: reset current session before setting the new one
+    - powerpc/booke: Disable STRICT_KERNEL_RWX, DEBUG_PAGEALLOC and KFENCE
+    - usb: dwc3: gadget: Skip resizing EP's TX FIFO if already resized
+    - firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
+    - soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
+    - soc: qcom: apr: Add of_node_put() before return
+    - arm64: dts: qcom: pmi8994: Fix "eternal"->"external" typo in WLED node
+    - arm64: dts: qcom: sdm845: Use RPMH_CE_CLK macro directly
+    - arm64: dts: qcom: sdm845: Fix Qualcomm crypto engine bus clock
+    - pinctrl: equilibrium: Fix function addition in multiple groups
+    - ASoC: topology: Fix stub for snd_soc_tplg_component_remove()
+    - phy: qcom-qusb2: Fix a memory leak on probe
+    - phy: ti: gmii-sel: check of_get_address() for failure
+    - phy: qcom-qmp: another fix for the sc8180x PCIe definition
+    - phy: qcom-snps: Correct the FSEL_MASK
+    - phy: Sparx5 Eth SerDes: Fix return value check in sparx5_serdes_probe()
+    - serial: xilinx_uartps: Fix race condition causing stuck TX
+    - clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
+    - clk: at91: clk-master: check if div or pres is zero
+    - clk: at91: clk-master: fix prescaler logic
+    - HID: u2fzero: clarify error check and length calculations
+    - HID: u2fzero: properly handle timeouts in usb_submit_urb
+    - powerpc/nohash: Fix __ptep_set_access_flags() and ptep_set_wrprotect()
+    - powerpc/book3e: Fix set_memory_x() and set_memory_nx()
+    - powerpc/44x/fsp2: add missing of_node_put
+    - powerpc/xmon: fix task state output
+    - ALSA: oxfw: fix functional regression for Mackie Onyx 1640i in v5.14 or
+      later
+    - iommu/dma: Fix incorrect error return on iommu deferred attach
+    - powerpc: Don't provide __kernel_map_pages() without
+      ARCH_SUPPORTS_DEBUG_PAGEALLOC
+    - ASoC: cs42l42: Correct configuring of switch inversion from ts-inv
+    - RDMA/hns: Fix initial arm_st of CQ
+    - RDMA/hns: Modify the value of MAX_LP_MSG_LEN to meet hardware compatibility
+    - ASoC: rsnd: Fix an error handling path in 'rsnd_node_count()'
+    - serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
+    - virtio_ring: check desc == NULL when using indirect with packed
+    - vdpa/mlx5: Fix clearing of VIRTIO_NET_F_MAC feature bit
+    - mips: cm: Convert to bitfield API to fix out-of-bounds access
+    - power: supply: bq27xxx: Fix kernel crash on IRQ handler register error
+    - RDMA/core: Require the driver to set the IOVA correctly during rereg_mr
+    - apparmor: fix error check
+    - rpmsg: Fix rpmsg_create_ept return when RPMSG config is not defined
+    - mtd: rawnand: intel: Fix potential buffer overflow in probe
+    - nfsd: don't alloc under spinlock in rpc_parse_scope_id
+    - rtc: ds1302: Add SPI ID table
+    - rtc: ds1390: Add SPI ID table
+    - rtc: pcf2123: Add SPI ID table
+    - remoteproc: imx_rproc: Fix TCM io memory type
+    - i2c: i801: Use PCI bus rescan mutex to protect P2SB access
+    - dmaengine: idxd: move out percpu_ref_exit() to ensure it's outside
+      submission
+    - rtc: mcp795: Add SPI ID table
+    - Input: ariel-pwrbutton - add SPI device ID table
+    - i2c: mediatek: fixing the incorrect register offset
+    - NFS: Default change_attr_type to NFS4_CHANGE_TYPE_IS_UNDEFINED
+    - NFS: Don't set NFS_INO_DATA_INVAL_DEFER and NFS_INO_INVALID_DATA
+    - NFS: Ignore the directory size when marking for revalidation
+    - NFS: Fix dentry verifier races
+    - pnfs/flexfiles: Fix misplaced barrier in nfs4_ff_layout_prepare_ds
+    - drm/bridge/lontium-lt9611uxc: fix provided connector suport
+    - drm/plane-helper: fix uninitialized variable reference
+    - PCI: aardvark: Don't spam about PIO Response Status
+    - PCI: aardvark: Fix preserving PCI_EXP_RTCTL_CRSSVE flag on emulated bridge
+    - opp: Fix return in _opp_add_static_v2()
+    - NFS: Fix deadlocks in nfs_scan_commit_list()
+    - sparc: Add missing "FORCE" target when using if_changed
+    - fs: orangefs: fix error return code of orangefs_revalidate_lookup()
+    - Input: st1232 - increase "wait ready" timeout
+    - drm/bridge: nwl-dsi: Add atomic_get_input_bus_fmts
+    - mtd: spi-nor: hisi-sfc: Remove excessive clk_disable_unprepare()
+    - PCI: uniphier: Serialize INTx masking/unmasking and fix the bit operation
+    - mtd: rawnand: arasan: Prevent an unsupported configuration
+    - mtd: core: don't remove debugfs directory if device is in use
+    - remoteproc: Fix a memory leak in an error handling path in
+      'rproc_handle_vdev()'
+    - rtc: rv3032: fix error handling in rv3032_clkout_set_rate()
+    - dmaengine: at_xdmac: call at_xdmac_axi_config() on resume path
+    - dmaengine: at_xdmac: fix AT_XDMAC_CC_PERID() macro
+    - dmaengine: stm32-dma: fix stm32_dma_get_max_width
+    - NFS: Fix up commit deadlocks
+    - NFS: Fix an Oops in pnfs_mark_request_commit()
+    - Fix user namespace leak
+    - auxdisplay: img-ascii-lcd: Fix lock-up when displaying empty string
+    - auxdisplay: ht16k33: Connect backlight to fbdev
+    - auxdisplay: ht16k33: Fix frame buffer device blanking
+    - soc: fsl: dpaa2-console: free buffer before returning from
+      dpaa2_console_read
+    - netfilter: nfnetlink_queue: fix OOB when mac header was cleared
+    - dmaengine: dmaengine_desc_callback_valid(): Check for `callback_result`
+    - dmaengine: tegra210-adma: fix pm runtime unbalance
+    - dmanegine: idxd: fix resource free ordering on driver removal
+    - dmaengine: idxd: reconfig device after device reset command
+    - signal/sh: Use force_sig(SIGKILL) instead of do_group_exit(SIGKILL)
+    - m68k: set a default value for MEMORY_RESERVE
+    - watchdog: f71808e_wdt: fix inaccurate report in WDIOC_GETTIMEOUT
+    - ar7: fix kernel builds for compiler test
+    - scsi: target: core: Remove from tmr_list during LUN unlink
+    - scsi: qla2xxx: Relogin during fabric disturbance
+    - scsi: qla2xxx: Fix gnl list corruption
+    - scsi: qla2xxx: Turn off target reset during issue_lip
+    - scsi: qla2xxx: edif: Fix app start fail
+    - scsi: qla2xxx: edif: Fix app start delay
+    - scsi: qla2xxx: edif: Flush stale events and msgs on session down
+    - scsi: qla2xxx: edif: Increase ELS payload
+    - scsi: qla2xxx: edif: Fix EDIF bsg
+    - NFSv4: Fix a regression in nfs_set_open_stateid_locked()
+    - dmaengine: idxd: fix resource leak on dmaengine driver disable
+    - i2c: xlr: Fix a resource leak in the error handling path of
+      'xlr_i2c_probe()'
+    - gpio: realtek-otto: fix GPIO line IRQ offset
+    - xen-pciback: Fix return in pm_ctrl_init()
+    - nbd: fix max value for 'first_minor'
+    - nbd: fix possible overflow for 'first_minor' in nbd_dev_add()
+    - io-wq: fix max-workers not correctly set on multi-node system
+    - net: davinci_emac: Fix interrupt pacing disable
+    - kselftests/net: add missed icmp.sh test to Makefile
+    - kselftests/net: add missed setup_loopback.sh/setup_veth.sh to Makefile
+    - kselftests/net: add missed SRv6 tests
+    - kselftests/net: add missed vrf_strict_mode_test.sh test to Makefile
+    - kselftests/net: add missed toeplitz.sh/toeplitz_client.sh to Makefile
+    - ethtool: fix ethtool msg len calculation for pause stats
+    - openrisc: fix SMP tlb flush NULL pointer dereference
+    - net: vlan: fix a UAF in vlan_dev_real_dev()
+    - net: dsa: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
+    - ice: Fix replacing VF hardware MAC to existing MAC filter
+    - ice: Fix not stopping Tx queues for VFs
+    - kdb: Adopt scheduler's task classification
+    - ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
+    - PCI: j721e: Fix j721e_pcie_probe() error path
+    - nvdimm/btt: do not call del_gendisk() if not needed
+    - scsi: bsg: Fix errno when scsi_bsg_register_queue() fails
+    - scsi: ufs: ufshpb: Use proper power management API
+    - scsi: ufs: core: Fix NULL pointer dereference
+    - scsi: ufs: ufshpb: Properly handle max-single-cmd
+    - drm/nouveau/svm: Fix refcount leak bug and missing check against null bug
+    - nvdimm/pmem: cleanup the disk if pmem_release_disk() is yet assigned
+    - block/ataflop: use the blk_cleanup_disk() helper
+    - block/ataflop: add registration bool before calling del_gendisk()
+    - block/ataflop: provide a helper for cleanup up an atari disk
+    - ataflop: remove ataflop_probe_lock mutex
+    - PCI: Do not enable AtomicOps on VFs
+    - cpufreq: intel_pstate: Clear HWP desired on suspend/shutdown and offline
+    - net: phy: fix duplex out of sync problem while changing settings
+    - block: fix device_add_disk() kobject_create_and_add() error handling
+    - drm/ttm: remove ttm_bo_vm_insert_huge()
+    - bonding: Fix a use-after-free problem when bond_sysfs_slave_add() failed
+    - octeontx2-pf: select CONFIG_NET_DEVLINK
+    - ALSA: memalloc: Catch call with NULL snd_dma_buffer pointer
+    - mfd: core: Add missing of_node_put for loop iteration
+    - mfd: cpcap: Add SPI device ID table
+    - mfd: sprd: Add SPI device ID table
+    - mfd: altera-sysmgr: Fix a mistake caused by resource_size conversion
+    - ACPI: PM: Fix device wakeup power reference counting error
+    - libbpf: Fix lookup_and_delete_elem_flags error reporting
+    - selftests/bpf/xdp_redirect_multi: Put the logs to tmp folder
+    - selftests/bpf/xdp_redirect_multi: Use arping to accurate the arp number
+    - selftests/bpf/xdp_redirect_multi: Give tcpdump a chance to terminate cleanly
+    - selftests/bpf/xdp_redirect_multi: Limit the tests in netns
+    - drm: fb_helper: improve CONFIG_FB dependency
+    - Revert "drm/imx: Annotate dma-fence critical section in commit path"
+    - drm/amdgpu/powerplay: fix sysfs_emit/sysfs_emit_at handling
+    - can: etas_es58x: es58x_rx_err_msg(): fix memory leak in error path
+    - can: mcp251xfd: mcp251xfd_chip_start(): fix error handling for
+      mcp251xfd_chip_rx_int_enable()
+    - mm/zsmalloc.c: close race window between zs_pool_dec_isolated() and
+      zs_unregister_migration()
+    - zram: off by one in read_block_state()
+    - perf bpf: Add missing free to bpf_event__print_bpf_prog_info()
+    - llc: fix out-of-bound array index in llc_sk_dev_hash()
+    - nfc: pn533: Fix double free when pn533_fill_fragment_skbs() fails
+    - litex_liteeth: Fix a double free in the remove function
+    - arm64: arm64_ftr_reg->name may not be a human-readable string
+    - arm64: pgtable: make __pte_to_phys/__phys_to_pte_val inline functions
+    - bpf, sockmap: Remove unhash handler for BPF sockmap usage
+    - bpf, sockmap: Fix race in ingress receive verdict with redirect to self
+    - bpf: sockmap, strparser, and tls are reusing qdisc_skb_cb and colliding
+    - bpf, sockmap: sk_skb data_end access incorrect when src_reg = dst_reg
+    - dmaengine: stm32-dma: fix burst in case of unaligned memory address
+    - dmaengine: stm32-dma: avoid 64-bit division in stm32_dma_get_max_width
+    - gve: Fix off by one in gve_tx_timeout()
+    - drm/i915/fb: Fix rounding error in subsampled plane size calculation
+    - init: make unknown command line param message clearer
+    - seq_file: fix passing wrong private data
+    - drm/amdgpu: fix uvd crash on Polaris12 during driver unloading
+    - net: dsa: mv88e6xxx: Don't support >1G speeds on 6191X on ports other than
+      10
+    - net/sched: sch_taprio: fix undefined behavior in ktime_mono_to_any
+    - net: hns3: fix ROCE base interrupt vector initialization bug
+    - net: hns3: fix pfc packet number incorrect after querying pfc parameters
+    - net: hns3: fix kernel crash when unload VF while it is being reset
+    - net: hns3: allow configure ETS bandwidth of all TCs
+    - net: stmmac: allow a tc-taprio base-time of zero
+    - net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
+    - net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
+    - vsock: prevent unnecessary refcnt inc for nonblocking connect
+    - net/smc: fix sk_refcnt underflow on linkdown and fallback
+    - cxgb4: fix eeprom len when diagnostics not implemented
+    - selftests/net: udpgso_bench_rx: fix port argument
+    - thermal: int340x: fix build on 32-bit targets
+    - smb3: do not error on fsync when readonly
+    - ARM: 9155/1: fix early early_iounmap()
+    - ARM: 9156/1: drop cc-option fallbacks for architecture selection
+    - parisc: Fix backtrace to always include init funtion names
+    - parisc: Flush kernel data mapping in set_pte_at() when installing pte for
+      user page
+    - MIPS: fix duplicated slashes for Platform file path
+    - MIPS: fix *-pkg builds for loongson2ef platform
+    - MIPS: Fix assembly error from MIPSr2 code used within MIPS_ISA_ARCH_LEVEL
+    - x86/mce: Add errata workaround for Skylake SKX37
+    - PCI/MSI: Move non-mask check back into low level accessors
+    - PCI/MSI: Destroy sysfs before freeing entries
+    - KVM: x86: move guest_pv_has out of user_access section
+    - posix-cpu-timers: Clear task::posix_cputimers_work in copy_process()
+    - irqchip/sifive-plic: Fixup EOI failed when masked
+    - f2fs: should use GFP_NOFS for directory inodes
+    - f2fs: include non-compressed blocks in compr_written_block
+    - f2fs: fix UAF in f2fs_available_free_memory
+    - ceph: fix mdsmap decode when there are MDS's beyond max_mds
+    - erofs: fix unsafe pagevec reuse of hooked pclusters
+    - drm/i915/guc: Fix blocked context accounting
+    - block: Hold invalidate_lock in BLKDISCARD ioctl
+    - block: Hold invalidate_lock in BLKZEROOUT ioctl
+    - block: Hold invalidate_lock in BLKRESETZONE ioctl
+    - ksmbd: Fix buffer length check in fsctl_validate_negotiate_info()
+    - ksmbd: don't need 8byte alignment for request length in ksmbd_check_message
+    - dmaengine: ti: k3-udma: Set bchan to NULL if a channel request fail
+    - dmaengine: ti: k3-udma: Set r/tchan or rflow to NULL if request fail
+    - dmaengine: bestcomm: fix system boot lockups
+    - net, neigh: Enable state migration between NUD_PERMANENT and NTF_USE
+    - 9p/net: fix missing error check in p9_check_errors
+    - mm/filemap.c: remove bogus VM_BUG_ON
+    - memcg: prohibit unconditional exceeding the limit of dying tasks
+    - mm, oom: pagefault_out_of_memory: don't force global OOM for dying tasks
+    - mm, oom: do not trigger out_of_memory from the #PF
+    - mm, thp: lock filemap when truncating page cache
+    - mm, thp: fix incorrect unmap behavior for private pages
+    - mfd: dln2: Add cell for initializing DLN2 ADC
+    - video: backlight: Drop maximum brightness override for brightness zero
+    - bcache: fix use-after-free problem in bcache_device_free()
+    - bcache: Revert "bcache: use bvec_virt"
+    - PM: sleep: Avoid calling put_device() under dpm_list_mtx
+    - s390/cpumf: cpum_cf PMU displays invalid value after hotplug remove
+    - s390/cio: check the subchannel validity for dev_busid
+    - s390/tape: fix timer initialization in tape_std_assign()
+    - s390/ap: Fix hanging ioctl caused by orphaned replies
+    - s390/cio: make ccw_device_dma_* more robust
+    - remoteproc: elf_loader: Fix loading segment when is_iomem true
+    - remoteproc: Fix the wrong default value of is_iomem
+    - remoteproc: imx_rproc: Fix ignoring mapping vdev regions
+    - remoteproc: imx_rproc: Fix rsc-table name
+    - mtd: rawnand: fsmc: Fix use of SM ORDER
+    - mtd: rawnand: ams-delta: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: xway: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: mpc5121: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: gpio: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: pasemi: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: orion: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: plat_nand: Keep the driver compatible with on-die ECC engines
+    - mtd: rawnand: au1550nd: Keep the driver compatible with on-die ECC engines
+    - powerpc/vas: Fix potential NULL pointer dereference
+    - powerpc/bpf: Fix write protecting JIT code
+    - powerpc/32e: Ignore ESR in instruction storage interrupt handler
+    - powerpc/powernv/prd: Unregister OPAL_MSG_PRD2 notifier during module unload
+    - powerpc/security: Use a mutex for interrupt exit code patching
+    - powerpc/64s/interrupt: Fix check_return_regs_valid() false positive
+    - powerpc/pseries/mobility: ignore ibm, platform-facilities updates
+    - powerpc/85xx: fix timebase sync issue when CONFIG_HOTPLUG_CPU=n
+    - drm/sun4i: Fix macros in sun8i_csc.h
+    - PCI: Add PCI_EXP_DEVCTL_PAYLOAD_* macros
+    - PCI: aardvark: Fix PCIe Max Payload Size setting
+    - SUNRPC: Partial revert of commit 6f9f17287e78
+    - drm/amd/display: Look at firmware version to determine using dmub on dcn21
+    - media: vidtv: move kfree(dvb) to vidtv_bridge_dev_release()
+    - cifs: fix memory leak of smb3_fs_context_dup::server_hostname
+    - ath10k: fix invalid dma_addr_t token assignment
+    - mmc: moxart: Fix null pointer dereference on pointer host
+    - selftests/x86/iopl: Adjust to the faked iopl CLI/STI usage
+    - selftests/bpf: Fix also no-alu32 strobemeta selftest
+    - arch/cc: Introduce a function to check for confidential computing features
+    - x86/sev: Add an x86 version of cc_platform_has()
+    - x86/sev: Make the #VC exception stacks part of the default stacks storage
+    - media: videobuf2: always set buffer vb2 pointer
+    - media: videobuf2-dma-sg: Fix buf->vb NULL pointer dereference
+    - Linux 5.15.3
+
+  * kernel panic: NULL pointer dereference in wb_timer_f() (LP: #1947557) //
+    Jammy update: v5.15.3 upstream stable release (LP: #1951822)
+    - blk-wbt: prevent NULL pointer dereference in wb_timer_fn
+
+  * Medion Notebook Keyboard not working (LP: #1909814) // Jammy update: v5.15.3
+    upstream stable release (LP: #1951822)
+    - ACPI: resources: Add DMI-based legacy IRQ override quirk
+
+  * Enable CONFIG_INTEL_IOMMU_DEFAULT_ON and
+    CONFIG_INTEL_IOMMU_SCALABLE_MODE_DEFAULT_ON on jammy 5.15 (LP: #1951440)
+    - [Config] enable Intel DMA remapping options by default
+
+  * Thinkpad E14 Gen2: Kernel panic with trackpad and trackpoint enabled
+    (LP: #1945590)
+    - SAUCE: Input: elantech - Fix stack out of bound access in
+      elantech_change_report_id()
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: LSM: Specify which LSM to display (using struct cred as input)
+    - SAUCE: selftests/seccomp: fix check of fds being assigned
+    - [Config] enable SUNRPC_DISABLE_INSECURE_ENCTYPES
+    - [Config] updateconfigs following v5.15.3, v5.15.4 import
+
+  * Miscellaneous upstream changes
+    - binder: use cred instead of task for selinux checks
+    - binder: use cred instead of task for getsecid
+    - Revert "UBUNTU: SAUCE: storvsc: use small sg_tablesize on x86"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 22 Nov 2021 13:14:15 +0100
+
+linux (5.15.0-11.11) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-11.11 -proposed tracker (LP: #1950948)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * OOPs on boot: invalid opcode: 0000 [#1] SMP NOPTI (LP: #1942215)
+    - SAUCE: ACPICA: prevent out-of-bound access with buggy DSDT
+    - [Config] disable UBSAN
+    - SAUCE: ACPICA: avoid accessing operands out-of-bounds
+
+  * Jammy update: v5.15.2 upstream stable release (LP: #1950949)
+    - KVM: x86: avoid warning with -Wbitwise-instead-of-logical
+    - Revert "x86/kvm: fix vcpu-id indexed array sizes"
+    - usb: ehci: handshake CMD_RUN instead of STS_HALT
+    - usb: gadget: Mark USB_FSL_QE broken on 64-bit
+    - usb: musb: Balance list entry in musb_gadget_queue
+    - usb-storage: Add compatibility quirk flags for iODD 2531/2541
+    - Revert "proc/wchan: use printk format instead of lookup_symbol_name()"
+    - binder: use euid from cred instead of using task
+    - binder: don't detect sender/target during buffer cleanup
+    - kfence: always use static branches to guard kfence_alloc()
+    - kfence: default to dynamic branch instead of static keys mode
+    - btrfs: fix lzo_decompress_bio() kmap leakage
+    - staging: rtl8712: fix use-after-free in rtl8712_dl_fw
+    - isofs: Fix out of bound access for corrupted isofs image
+    - comedi: dt9812: fix DMA buffers on stack
+    - comedi: ni_usb6501: fix NULL-deref in command paths
+    - comedi: vmk80xx: fix transfer-buffer overflows
+    - comedi: vmk80xx: fix bulk-buffer overflow
+    - comedi: vmk80xx: fix bulk and interrupt message timeouts
+    - staging: r8712u: fix control-message timeout
+    - staging: rtl8192u: fix control-message timeouts
+    - staging: r8188eu: fix memleak in rtw_wx_set_enc_ext
+    - media: staging/intel-ipu3: css: Fix wrong size comparison imgu_css_fw_init
+    - rsi: fix control-message timeout
+    - Linux 5.15.2
+
+  * reuseport_bpf_numa in net from ubuntu_kernel_selftests fails on ppc64le
+    (LP: #1867570)
+    - selftests/net: Fix reuseport_bpf_numa by skipping unavailable nodes
+
+  * Miscellaneous Ubuntu changes
+    - packaging: switch getabis to the linux package name
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: (no-up) rename the adv7511 drm driver to adv7511_drm"
+    - Revert "UBUNTU: SAUCE: drm/i915/dp: Use max params for older panels"
+    - Revert "UBUNTU: SAUCE: i915: Fix build error due to missing struct
+      definition"
+    - selftests/core: fix conflicting types compile error for close_range()
+    - selftests: net: test_vxlan_under_vrf: fix HV connectivity test
+    - Revert "UBUNTU: SAUCE: ACPICA: prevent out-of-bound access with buggy DSDT"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 15 Nov 2021 10:12:47 +0100
+
+linux (5.15.0-10.10) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-10.10 -proposed tracker (LP: #1950133)
+
+  * Jammy update: v5.15.1 upstream stable release (LP: #1950131)
+    - sfc: Fix reading non-legacy supported link modes
+    - media: firewire: firedtv-avc: fix a buffer overflow in avc_ca_pmt()
+    - Revert "xhci: Set HCD flag to defer primary roothub registration"
+    - Revert "usb: core: hcd: Add support for deferring roothub registration"
+    - drm/amdkfd: fix boot failure when iommu is disabled in Picasso.
+    - Revert "soc: imx: gpcv2: move reset assert after requesting domain power up"
+    - ARM: 9120/1: Revert "amba: make use of -1 IRQs warn"
+    - Revert "wcn36xx: Disable bmps when encryption is disabled"
+    - drm/amdgpu: revert "Add autodump debugfs node for gpu reset v8"
+    - drm/amd/display: Revert "Directly retrain link from debugfs"
+    - Revert "drm/i915/gt: Propagate change in error status to children on unhold"
+    - ALSA: usb-audio: Add quirk for Audient iD14
+    - Linux 5.15.1
+
+  * Miscellaneous Ubuntu changes
+    - packaging: fixup previous ABI/spin to -9.9
+    - [Packaging] Drop unused d-i build-deps and packaging
+    - [Packaging] Drop now unsupported d-i/ input files
+
+  * Miscellaneous upstream changes
+    - selftests: net: properly support IPv6 in GSO GRE test
+    - signal: Add SA_IMMUTABLE to ensure forced siganls do not get changed
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 08 Nov 2021 14:43:24 +0100
+
+linux (5.15.0-9.9) jammy; urgency=medium
+
+  * jammy/linux: 5.15.0-1.1 -proposed tracker (LP: #1949876)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - [Packaging] update Ubuntu.md
+
+  * Add F81966 watchdog support (LP: #1949063)
+    - SAUCE: ODM: watchdog: f71808e_wdt: Add F81966 support
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Rewrite debian/scripts/misc/insert-changes.pl in Python
+    - [Packaging] change source package name to linux
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 04 Nov 2021 18:47:19 +0100
+
+linux (5.15.0-0.0) jammy; urgency=medium
+
+  * Empty entry
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 04 Nov 2021 16:47:16 +0100
+
+linux-unstable (5.15.0-8.8) jammy; urgency=medium
+
+  * jammy/linux-unstable: 5.15.0-8.8 -proposed tracker (LP: #1949436)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Drop "UBUNTU: SAUCE: cachefiles: Page leaking in
+    cachefiles_read_backing_file while vmscan is active" (LP: #1947709)
+    - Revert "UBUNTU: SAUCE: cachefiles: Page leaking in
+      cachefiles_read_backing_file while vmscan is active"
+
+  * Add l2tp.sh in net from ubuntu_kernel_selftests back (LP: #1934293)
+    - Revert "UBUNTU: SAUCE: selftests/net -- disable l2tp.sh test"
+
+  * Check for changes relevant for security certifications (LP: #1945989)
+    - [Packaging] Add fips-checks as part of finalchecks
+
+  * Add final-checks to check certificates (LP: #1947174)
+    - [Packaging] Add system trusted and revocation keys final check
+
+  * Can only reach PC3 when ethernet is plugged r8169 (LP: #1946433)
+    - r8169: Enable chip-specific ASPM regardless of PCIe ASPM status
+    - PCI/ASPM: Introduce a new helper to report ASPM capability
+    - r8169: Implement dynamic ASPM mechanism
+
+  * rtw89 kernel module for Realtek 8852 wifi is missing (LP: #1945967)
+    - rtw89: add Realtek 802.11ax driver
+    - rtw89: Remove redundant check of ret after call to rtw89_mac_enable_bb_rf
+    - rtw89: fix return value check in rtw89_cam_send_sec_key_cmd()
+    - rtw89: remove unneeded semicolon
+    - [Config] RTW89=m
+
+  * Fix A yellow screen pops up in an instant (< 1 second) and then disappears
+    before loading the system (LP: #1945932)
+    - drm/i915: Stop force enabling pipe bottom color gammma/csc
+
+  * disable CONFIG_KFENCE_STATIC_KEYS in linux 5.15 (LP: #1948038)
+    - [Config] disable CONFIG_KFENCE_STATIC_KEYS
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Remove old and unused firmware helper scripts
+    - [Packaging] Replace Perl oneliner with Bash statements
+    - rebase to v5.15
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 02 Nov 2021 08:29:45 +0100
+
+linux-unstable (5.15.0-7.7) jammy; urgency=medium
+
+  * jammy/linux-unstable: 5.15.0-7.7 -proposed tracker (LP: #1948770)
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Temporarily disable signing for ppc64el and s390x
+    - packaging: switch release to Jammy
+    - rebase to v5.15-rc7
+    - [Config] GCC version update
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc7
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 26 Oct 2021 11:38:14 +0200
+
+linux-unstable (5.15.0-6.6) jammy; urgency=medium
+
+  * impish/linux-unstable: 5.15.0-6.6 -proposed tracker (LP: #1947565)
+
+  * [impish] Remove the downstream xr-usb-uart driver (LP: #1945938)
+    - SAUCE: xr-usb-serial: remove driver
+    - [Config] update modules list
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.15-rc6
+    - [Config] update config & annotations following v5.15-rc6 rebase
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: xr-usb-serial: switch to tty_alloc_driver() and
+      tty_driver_kref_put()"
+    - Revert "UBUNTU: SAUCE: xr-usb-serial: update return code for
+      xr_usb_serial_tty_write_room() and xr_usb_serial_tty_chars_in_buffer()"
+    - Revert "UBUNTU: [Packaging] FTBFS: disable zfs"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc6
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 18 Oct 2021 12:24:45 +0200
+
+linux-unstable (5.15.0-5.5) impish; urgency=medium
+
+  * impish/linux-unstable: 5.15.0-5.5 -proposed tracker (LP: #1946338)
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.15-rc5
+    - [Config] FB_SIMPLE=m
+    - [Config] update annotations
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc5
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 11 Oct 2021 12:14:02 +0200
+
+linux-unstable (5.15.0-4.4) impish; urgency=medium
+
+  * impish/linux-unstable: 5.15.0-4.4 -proposed tracker (LP: #1945953)
+
+  * Fix missing HDMI audio on Intel RKL (LP: #1945556)
+    - drm/i915/audio: Use BIOS provided value for RKL HDA link
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: media: atomisp: add missing return type (fix -Werror=return-type)
+    - SAUCE: xr-usb-serial: switch to tty_alloc_driver() and tty_driver_kref_put()
+    - rebase to v5.15-rc4
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] FTBFS: disable INTEL_ATOMISP"
+    - Revert "UBUNTU: [Config] FTBFS: disable xr-usb-serial"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc4
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 04 Oct 2021 10:52:41 +0200
+
+linux-unstable (5.15.0-3.3) impish; urgency=medium
+
+  * impish/linux-unstable: 5.15.0-3.3 -proposed tracker (LP: #1944944)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.15-rc3
+    - [Config] updateconfigs following v5.15-rc3 rebase
+    - [Packaging] correctly evaluate release in update-dkms-versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc3
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 27 Sep 2021 16:48:03 +0200
+
+linux-unstable (5.15.0-2.2) impish; urgency=medium
+
+  * impish/linux-unstable: 5.15.0-2.2 -proposed tracker (LP: #1944423)
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.15-rc2
+    - [Config] updateconfigs following v5.15-rc2 rebase
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc2
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 21 Sep 2021 11:46:59 +0200
+
+linux-unstable (5.15.0-1.1) impish; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  *  LRMv5: switch primary version handling to kernel-versions data set
+    (LP: #1928921)
+    - [Packaging] switch to kernel-versions
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] remove remaining references to ports
+    - [Packaging] drop x32 architecture configs
+    - [Config] mark CONFIG_BPF_UNPRIV_DEFAULT_OFF enforced
+    - [Packaging] bump kernel version to 5.15
+    - rebase to v5.15-rc1
+    - [Config] updateconfigs following v5.15-rc1 rebase
+    - [Config] FTBFS: disable INTEL_ATOMISP
+    - [Config] FTBFS: disable xr-usb-serial
+    - [Packaging] FTBFS: disable zfs
+
+  * Miscellaneous upstream changes
+    - Revert "r8169: avoid link-up interrupt issue on RTL8106e if user enables
+      ASPM"
+    - Revert "UBUNTU: SAUCE: RDMA/core: Introduce peer memory interface"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.15-rc1
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Fri, 17 Sep 2021 11:42:25 +0200
+
+linux-unstable (5.15.0-0.0) impish; urgency=medium
+
+  * Empty entry
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Wed, 15 Sep 2021 11:54:10 +0200
+
+linux-unstable (5.14.0-9.9) impish; urgency=medium
+
+  * impish/linux-unstable: 5.14.0-9.9 -proposed tracker (LP: #1943022)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] NVIDIA -- Add the NVIDIA 470 driver
+    - [Packaging] NVIDIA: transition -460 and -465 to -470, transition -460-server
+      to -470-server
+
+  * Miscellaneous upstream changes
+    - vt_kdsetmode: extend console locking
+    - Bluetooth: btusb: check conditions before enabling USB ALT 3 for WBS
+    - net: dsa: mt7530: fix VLAN traffic leaks again
+    - btrfs: fix NULL pointer dereference when deleting device by invalid id
+    - Revert "floppy: reintroduce O_NDELAY fix"
+    - fscrypt: add fscrypt_symlink_getattr() for computing st_size
+    - ext4: report correct st_size for encrypted symlinks
+    - f2fs: report correct st_size for encrypted symlinks
+    - ubifs: report correct st_size for encrypted symlinks
+    - net: don't unconditionally copy_from_user a struct ifreq for socket ioctls
+    - audit: move put_tree() to avoid trim_trees refcount underflow and UAF
+    - Linux 5.14.1
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Wed, 08 Sep 2021 12:20:18 +0200
+
+linux-unstable (5.14.0-8.8) impish; urgency=medium
+
+  * impish/linux-unstable: 5.14.0-8.8 -proposed tracker (LP: #1941887)
+
+  * Fix  Intel AC9560 BT function cannot turn on if BT turn off before S3 entry
+    (LP: #1941696)
+    - SAUCE: Bluetooth: btusb: add a reject table to disable msft
+
+  *  Add USB4 support for AMD SoC (LP: #1941036)
+    - thunderbolt: Add vendor specific NHI quirk for auto-clearing interrupt
+      status
+    - thunderbolt: Handle ring interrupt by reading interrupt status register
+    - thunderbolt: Do not read control adapter config space
+    - thunderbolt: Fix port linking by checking all adapters
+
+  * Support builtin revoked certificates (LP: #1932029)
+    - [Config] Enforce SYSTEM_TRUSTED_KEYS and SYSTEM_REVOCATION_KEYS
+
+  * GPIO error logs in start and dmesg after update of kernel (LP: #1937897)
+    - ODM: mfd: Check AAEON BFPI version before adding device
+
+  * initramfs-tools & kernel: use zstd as the default compression method
+    (LP: #1931725)
+    - [Config] enforce ZSTD compression
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.14
+    - [Config] RESET_MCHP_SPARX5 depends on ARCH_SPARX5
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Packaging] FTBFS: disable zfs"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.14
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 30 Aug 2021 12:57:19 +0200
+
+linux-unstable (5.14.0-7.7) impish; urgency=medium
+
+  * Please enable CONFIG_UBSAN_BOUNDS (LP: #1914685)
+    - [Config] Enable CONFIG_UBSAN_BOUNDS
+
+  * CONFIG_HARDENED_USERCOPY_FALLBACK should be disabled (LP: #1855340)
+    - [Config] Disable CONFIG_HARDENED_USERCOPY_FALLBACK
+
+  * fs: removing mandatory locks (LP: #1940392)
+    - [Config] Disable CONFIG_MANDATORY_FILE_LOCKING
+
+  * Fix kernel panic caused by legacy devices on AMD platforms (LP: #1936682)
+    - SAUCE: iommu/amd: Keep swiotlb enabled to ensure devices with 32bit DMA
+      still work
+
+  * ALSA: hda/cs8409: Add support for dolphin (LP: #1939541)
+    - ALSA: hda/cirrus: Move CS8409 HDA bridge to separate module
+    - ALSA: hda/cs8409: Move arrays of configuration to a new file
+    - ALSA: hda/cs8409: Use enums for register names and coefficients
+    - ALSA: hda/cs8409: Mask all CS42L42 interrupts on initialization
+    - ALSA: hda/cs8409: Reduce HS pops/clicks for Cyborg
+    - ALSA: hda/cs8409: Disable unnecessary Ring Sense for Cyborg/Warlock/Bullseye
+    - ALSA: hda/cs8409: Disable unsolicited responses during suspend
+    - ALSA: hda/cs8409: Disable unsolicited response for the first boot
+    - ALSA: hda/cs8409: Mask CS42L42 wake events
+    - ALSA: hda/cs8409: Simplify CS42L42 jack detect.
+    - ALSA: hda/cs8409: Prevent I2C access during suspend time
+    - ALSA: hda/cs8409: Generalize volume controls
+    - ALSA: hda/cs8409: Dont disable I2C clock between consecutive accesses
+    - ALSA: hda/cs8409: Avoid setting the same I2C address for every access
+    - ALSA: hda/cs8409: Avoid re-setting the same page as the last access
+    - ALSA: hda/cs8409: Support i2c bulk read/write functions
+    - ALSA: hda/cs8409: Separate CS8409, CS42L42 and project functions
+    - ALSA: hda/cs8409: Move codec properties to its own struct
+    - ALSA: hda/cs8409: Support multiple sub_codecs for Suspend/Resume/Unsol
+      events
+    - ALSA: hda/cs8409: Add Support to disable jack type detection for CS42L42
+    - ALSA: hda/cs8409: Add support for dolphin
+    - ALSA: hda/cs8409: Enable Full Scale Volume for Line Out Codec on Dolphin
+    - ALSA: hda/cs8409: Set fixed sample rate of 48kHz for CS42L42
+    - ALSA: hda/cs8409: Use timeout rather than retries for I2C transaction waits
+    - ALSA: hda/cs8409: Remove unnecessary delays
+    - ALSA: hda/cs8409: Follow correct CS42L42 power down sequence for suspend
+    - ALSA: hda/cs8409: Unmute/Mute codec when stream starts/stops
+    - ALSA: hda/cs8409: Prevent pops and clicks during suspend
+    - SAUCE: ALSA: hda/cs8409: Prevent pops and clicks during reboot
+    - [Config] Enable Cirrus Logic HDA bridge support
+
+  * e1000e: add handshake with the Intel CSME to support S0ix (LP: #1937252)
+    - SAUCE: e1000e: Add handshake with the CSME to support S0ix
+    - SAUCE: e1000e: Add polling mechanism to indicate CSME DPG exit
+    - SAUCE: e1000e: Additional PHY power saving in S0ix
+
+  * AMDGPU: Fix System hang after resume from suspend (LP: #1940204)
+    - SAUCE: drm/amdgpu: disable BACO support for 699F:C7 polaris12 SKU
+      temporarily
+
+  * [Regression] Audio card [8086:9d71] not detected after upgrade from linux
+    5.4 to 5.8 (LP: #1915117)
+    - [Config] set CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC to y
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.14-rc7
+    - [Config] updateconfigs following 5.14-rc7 rebase
+    - [Config] Enable CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT
+    - [Config] annotations: set CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT to y
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] annotations: set
+      CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC to y"
+    - Revert "UBUNTU: [Config] set CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC to
+      y"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.14-rc7
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 24 Aug 2021 10:32:31 +0200
+
+linux-unstable (5.14.0-6.6) impish; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - no changes upload (to avoid picking up libc6 from -proposed)
+
+  * No changes upload (to avoid picking up libc6 from -proposed)
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Wed, 18 Aug 2021 13:41:16 +0200
+
+linux-unstable (5.14.0-5.5) impish; urgency=medium
+
+  * disable “CONFIG_HISI_DMA” config for ubuntu version (LP: #1936771)
+    - [Config] Disable CONFIG_HISI_DMA
+
+  * Dell XPS 17 (9710) PCI/internal sound card not detected  (LP: #1935850)
+    - ASoC: Intel: sof_sdw: include rt711.h for RT711 JD mode
+    - ASoC: Intel: sof_sdw: add quirk for Dell XPS 9710
+
+  * [regression] USB device is not detected during boot (LP: #1939638)
+    - SAUCE: Revert "usb: core: reduce power-on-good delay time of root hub"
+
+  * armhf build failure (LP: #1939308)
+    - SAUCE: arm: Fix instruction set selection for GCC 11
+
+  * REGRESSION: shiftfs lets sendfile fail with EINVAL (LP: #1939301)
+    - SAUCE: shiftfs: fix sendfile() invocations
+
+  * Wobbly graphics on built-in display since linux-image-5.11.0-22-generic
+    (LP: #1936708)
+    - SAUCE: drm/i915/dp: Use max params for older panels
+
+  * [SRU][H/OEM-5.10/OEM-5.13/U] Fix system hang after unplug tbt dock
+    (LP: #1938689)
+    - SAUCE: igc: fix page fault when thunderbolt is unplugged
+
+  * e1000e blocks the boot process when it tried to write checksum to its NVM
+    (LP: #1936998)
+    - SAUCE: e1000e: Do not take care about recovery NVM checksum
+
+  * [Regression] Audio card [8086:9d71] not detected after upgrade from linux
+    5.4 to 5.8 (LP: #1915117)
+    - [Config] set CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC to y
+    - [Config] annotations: set CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC to y
+
+  * Miscellaneous Ubuntu changes
+    - [Config] updateconfigs following 5.14-rc6 rebase
+    - rebase to v5.14-rc6
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.14-rc6
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 17 Aug 2021 17:49:15 +0200
+
+linux-unstable (5.14.0-4.4) impish; urgency=medium
+
+  * impish/linux-unstable: 5.14.0-4.4 -proposed tracker (LP: #1938566)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous upstream changes
+    - Revert "riscv: Get CPU manufacturer information"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 03 Aug 2021 14:50:27 +0200
+
+linux-unstable (5.14.0-3.3) impish; urgency=medium
+
+  * Add additional Mediatek MT7921 WiFi/BT device IDs (LP: #1937004)
+    - SAUCE: Bluetooth: btusb: Add Mediatek MT7921 support for Foxconn
+    - SAUCE: Bluetooth: btusb: Add Mediatek MT7921 support for IMC Network
+    - SAUCE: Bluetooth: btusb: Add support for Foxconn Mediatek Chip
+
+  * Fix display output on HP hybrid GFX laptops (LP: #1936296)
+    - drm/i915: Invoke another _DSM to enable MUX on HP Workstation laptops
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.14-rc3
+    - [Config] updateconfigs following 5.14-rc3 rebase
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.14-rc3
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 26 Jul 2021 12:52:38 +0200
+
+linux-unstable (5.14.0-2.2) impish; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: xr-usb-serial: update return code for xr_usb_serial_tty_write_room()
+      and xr_usb_serial_tty_chars_in_buffer()
+    - SAUCE: platform/x86: dell-uart-backlight: update return code for
+      uart_chars_in_buffer(()
+    - [Config] updateconfigs following 5.14-rc2 rebase
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] FTBFS: disable ubuntu/xr-usb-serial"
+    - Revert "UBUNTU: [Config] FTBFS: disable DELL_UART_BACKLIGHT"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.14-rc2
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 22 Jul 2021 11:03:28 +0200
+
+linux-unstable (5.14.0-1.1) impish; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] bump kernel version to 5.14
+    - [Config] updateconfigs following 5.14-rc1 rebase
+    - [Config] update annotations
+    - [Packaging] FTBFS: disable zfs
+    - [Config] FTBFS: disable DELL_UART_BACKLIGHT
+    - [Config] FTBFS: disable ubuntu/xr-usb-serial
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Packaging] update variants"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.14-rc1
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Fri, 16 Jul 2021 15:20:04 +0200
+
+linux-unstable (5.14.0-0.0) impish; urgency=medium
+
+  * Empty entry
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 13 Jul 2021 12:15:35 +0200
+
+linux (5.13.0-11.11) impish; urgency=medium
+
+  * impish/linux: 5.13.0-11.11 -proposed tracker (LP: #1933854)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+
+  * Support builtin revoked certificates (LP: #1932029)
+    - [Packaging] build canonical-revoked-certs.pem from branch/arch certs
+    - [Packaging] Revoke 2012 UEFI signing certificate as built-in
+    - [Config] Configure CONFIG_SYSTEM_REVOCATION_KEYS with revoked keys
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Change source package name to linux
+
+  * Miscellaneous upstream changes
+    - mm/page_alloc: Correct return value of populated elements if bulk array is
+      populated
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 29 Jun 2021 07:50:25 +0200
+
+linux (5.13.0-10.10) impish; urgency=medium
+
+  * Empty entry
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 28 Jun 2021 08:40:05 +0200
+
+linux-unstable (5.13.0-10.10) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-10.10 -proposed tracker (LP: #1933795)
+
+  * Pixel format change broken for Elgato Cam Link 4K (LP: #1932367)
+    - media: uvcvideo: Fix pixel format change for Elgato Cam Link 4K
+
+  * initramfs-tools & kernel: use zstd as the default compression method
+    (LP: #1931725)
+    - s390/decompressor: correct BOOT_HEAP_SIZE condition
+    - s390/boot: add zstd support
+    - [Packaging] use ZSTD to compress s390 kernels
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests: tls: fix chacha+bidir tests
+    - SAUCE: selftests: icmp_redirect: support expected failures
+    - [Config] update configs and annotations after rebase to 5.13
+
+  * Miscellaneous upstream changes
+    - tls: prevent oversized sendfile() hangs by ignoring MSG_MORE
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 28 Jun 2021 08:40:05 +0200
+
+linux-unstable (5.13.0-9.9) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-9.9 -proposed tracker (LP: #1933070)
+
+  * Add support for selective build of special drivers (LP: #1912789)
+    - [Packaging] Add support for ODM drivers
+    - [Packaging] Turn on ODM support for amd64
+    - [Packaging] Fix ODM support in actual build
+    - [Packaging] Fix ODM DRIVERS Kconfig
+
+  * Add support for IO functions of AAEON devices (LP: #1929504)
+    - ODM: [Config] update config for AAEON devices
+    - ODM: hwmon: add driver for AAEON devices
+    - ODM: leds: add driver for AAEON devices
+    - ODM: watchdog: add driver for AAEON devices
+    - ODM: gpio: add driver for AAEON devices
+    - ODM: mfd: Add support for IO functions of AAEON devices
+
+  * Disable hv-kvp-daemon.service on certain instance types (LP: #1932081)
+    - [Packaging]: Add kernel command line condition to hv-kvp-daemon service
+
+  * Fix non-working GPU on Some HP desktops (LP: #1931147)
+    - PCI: Coalesce host bridge contiguous apertures
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests: seccomp: bump up timeout to 5min
+    - SAUCE: Revert "net/tls(TLS_SW): Add selftest for 'chunked' sendfile test"
+    - [Config] update annotations after rebase to 5.13-rc7
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13-rc7
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 21 Jun 2021 10:55:36 +0200
+
+linux-unstable (5.13.0-8.8) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-8.8 -proposed tracker (LP: #1932018)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * initramfs-tools & kernel: use zstd as the default compression method
+    (LP: #1931725)
+    - [Config] use ZSTD to compress amd64 kernels
+
+  * Miscellaneous Ubuntu changes
+    - [Config] enable signing for ppc64el
+    - SAUCE: powerpc: Fix initrd corruption with relative jump labels
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 15 Jun 2021 15:07:34 +0200
+
+linux-unstable (5.13.0-7.7) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-7.7 -proposed tracker (LP: #1931840)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+    - [Packaging] resync getabis
+    - [Packaging] update helper scripts
+    - update dkms package versions
+
+  * Intel ADL-S graphics feature enabling (LP: #1931240)
+    - SAUCE: drm/i915/adl_s: ADL-S platform Update PCI ids for Mobile BGA
+
+  * Kernel package builds running out of space on builders (LP: #1930713)
+    - [Config] CONFIG_DEBUG_INFO_COMPRESSED=n
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] remove nvidia dkms build support
+    - [Config] remove now unsued do_dkms_nvidia* build variables
+    - [Config] enable signing for s390x
+    - [Config] update annotations after configs review
+    - [Config] update toolchain versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 14 Jun 2021 11:53:08 +0200
+
+linux-unstable (5.13.0-6.6) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-6.6 -proposed tracker (LP: #1931071)
+
+  * Kernel package builds running out of space on builders (LP: #1930713)
+    - [Debian] use stamps for flavour install targets
+    - [Debian] run install-$(flavour) targets during build phase
+    - [Debian] remove dh_testroot from install targets
+    - [Debian] dkms-build -- use fakeroot if not running as root
+    - [Debian] exclude $(DEBIAN)/__abi.current from linux-source
+
+  * [UBUNTU 21.04] tools/kvm_stat: Add restart delay (LP: #1921870)
+    - [Debian] install kvm_stat systemd service
+
+  * Debugging symbols (dbgsym) packages are missing GDB kernel scripts
+    (LP: #1928715)
+    - [Packaging] Build and include GDB Python scripts into debug packages
+
+  * Can't detect intel wifi 6235 (LP: #1920180)
+    - SAUCE: iwlwifi: add new pci id for 6235
+
+  * Select correct boot VGA when BIOS doesn't do it properly (LP: #1929217)
+    - vgaarb: Use ACPI HID name to find integrated GPU
+
+  * Fix kernel panic on Intel Bluetooth (LP: #1928838)
+    - Bluetooth: Shutdown controller after workqueues are flushed or cancelled
+
+  * build module CONFIG_SND_SOC_INTEL_SOUNDWIRE_SOF_MACH=m for 5.11,  5.13-rc2
+    and later (LP: #1921632)
+    - [Config] enable soundwire audio mach driver
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_SND_SOC_RT1308 can only be enabled on amd64
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13-rc5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 07 Jun 2021 10:45:13 +0200
+
+linux-unstable (5.13.0-5.5) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-5.5 -proposed tracker (LP: #1930205)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Config] set CONFIG_BPF_UNPRIV_DEFAULT_OFF=y
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 31 May 2021 12:32:38 +0200
+
+linux-unstable (5.13.0-4.4) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-4.4 -proposed tracker (LP: #1929404)
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Support importing mokx keys into revocation list from the mok table
+    (LP: #1928679)
+    - SAUCE: integrity: add informational messages when revoking certs
+
+  * Support importing mokx keys into revocation list from the mok table
+    (LP: #1928679) // CVE-2020-26541 when certificates are revoked via
+    MokListXRT.
+    - SAUCE: integrity: Load mokx certs from the EFI MOK config table
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Temporarily disable signing for ppc64el and s390x
+    - SAUCE: Revert "UBUNTU: SAUCE: overlayfs: Be more careful about copying up
+      sxid files"
+    - SAUCE: Revert "UBUNTU: SAUCE: overlayfs: Propogate nosuid from lower and
+      upper mounts"
+    - SAUCE: Revert "UBUNTU: SAUCE: overlayfs: Enable user namespace mounts"
+    - SAUCE: Revert "UBUNTU: SAUCE: overlayfs: ensure mounter privileges when
+      reading directories"
+    - SAUCE: Revert "UBUNTU: SAUCE: fs: Move SB_I_NOSUID to the top of s_iflags"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13-rc3
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 24 May 2021 13:06:17 +0200
+
+linux-unstable (5.13.0-3.3) impish; urgency=medium
+
+  * impish/linux-unstable: 5.13.0-3.3 -proposed tracker (LP: #1928655)
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13-rc2
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 17 May 2021 11:55:02 +0200
+
+linux-unstable (5.13.0-2.2) impish; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] enable CONFIG_DEBUG_INFO_COMPRESSED
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] temporarily disable BPF JIT"
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Fri, 14 May 2021 09:19:02 +0200
+
+linux-unstable (5.13.0-1.1) impish; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.13-rc1
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 12 May 2021 11:35:23 +0200
+
+linux-unstable (5.13.0-0.0) impish; urgency=medium
+
+  * Empty entry
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 11 May 2021 08:40:09 +0200
+
+linux-unstable (5.12.0-11.11) impish; urgency=medium
+
+  * Impish update: v5.12.1 upstream stable release (LP: #1927094)
+    - net: hso: fix NULL-deref on disconnect regression
+    - USB: CDC-ACM: fix poison/unpoison imbalance
+    - iwlwifi: Fix softirq/hardirq disabling in iwl_pcie_gen2_enqueue_hcmd()
+    - cfg80211: fix locking in netlink owner interface destruction
+    - mei: me: add Alder Lake P device id.
+    - Linux 5.12.1
+
+  * Packaging resync (LP: #1786013) // Impish update: v5.12.1 upstream stable
+    release (LP: #1927094)
+    - update dkms package versions
+
+  * Gigabyte R120-T33 (ARM ThunderX SoC) fails to boot in ACPI mode
+    (LP: #1925075) // Impish update: v5.12.1 upstream stable release
+    (LP: #1927094)
+    - ACPI: GTDT: Don't corrupt interrupt mappings on watchdow probe failure
+
+  * Fix kernel panic at boot on dual GFX systems (LP: #1926792) // Impish
+    update: v5.12.1 upstream stable release (LP: #1927094)
+    - drm/amdgpu: Register VGA clients after init can no longer fail
+
+  * On TGL platforms screen shows garbage when browsing website by scrolling
+    mouse (LP: #1926579) // Impish update: v5.12.1 upstream stable release
+    (LP: #1927094)
+    - SAUCE: drm/i915/display: Disable PSR2 if TGL Display stepping is B1 from A0
+
+  * CirrusLogic: Cracking noises appears in built-in speaker when output volume
+    is set >80% (LP: #1924997) // Impish update: v5.12.1 upstream stable release
+    (LP: #1927094)
+    - SAUCE: ALSA: hda/cirrus: Use CS8409 Equalizer to fix abnormal sounds on
+      Bullseye
+
+  * Enable mute/micmute LEDs and limit mic boost on EliteBook 845 G8
+    (LP: #1925415) // Impish update: v5.12.1 upstream stable release
+    (LP: #1927094)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook
+      845 G8
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: PCI: Disable broken RTIT_BAR of Intel TH"
+    - Revert "UBUNTU: [Config] temporarily disable ZFS"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 04 May 2021 18:35:54 +0200
+
+linux-unstable (5.12.0-10.10) impish; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Drop versioned ABI directory names
+    - [Packaging] getabis: Download ABIs into an unversioned directory
+    - [Packaging] final-checks: Handle unversioned ABI directories
+    - bump to impish
+    - [Config] GCC version update
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 29 Apr 2021 12:27:20 +0200
+
+linux-unstable (5.12.0-9.9) impish; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc8
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 26 Apr 2021 11:14:16 -0500
+
+linux-unstable (5.12.0-8.8) hirsute; urgency=medium
+
+  * CVE-2021-3492
+    - SAUCE: shiftfs: free allocated memory in shiftfs_btrfs_ioctl_fd_replace()
+      error paths
+    - SAUCE: shiftfs: handle copy_to_user() return values correctly
+
+  * Fix no picture from HDMI when it's plugged after boot (LP: #1924238)
+    - drm/i915/display: Handle lane polarity for DDI port
+
+  * hirsute beta desktop AMD64 ISO kernel panic on boot when booting using UEFI
+    (LP: #1922403)
+    - SAUCE: efifb: Check efifb_pci_dev before using it
+
+  * Miscellaneous Ubuntu changes
+    - Rebase to v5.12-rc8
+    - [Config] updateconfigs following 5.12-rc8 rebase
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc8
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 19 Apr 2021 11:37:27 +0200
+
+linux-unstable (5.12.0-7.7) hirsute; urgency=medium
+
+  * drm/i915: Drop force_probe requirement for Rocket Lake (LP: #1905466)
+    - drm/i915/rkl: Remove require_force_probe protection
+
+  * HP m400 cartridges fail to find NIC when deploying hirsute (LP: #1918793)
+    - PCI: xgene: Fix cfg resource mapping
+
+  * Update - Fix no screen show on display after S3 on CML-R  (LP: #1922768)
+    - drm/i915/gen9bc: Handle TGP PCH during suspend/resume
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: RDMA/core: Introduce peer memory interface
+    - Rebase to v5.12-rc7
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc7
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 12 Apr 2021 11:48:07 +0200
+
+linux-unstable (5.12.0-6.6) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+
+  * i915 doesn't support some high pixel clock 4k * 60Hz monitors (LP: #1922372)
+    - drm/i915/vbt: update DP max link rate table
+
+  * Tegra "mmc0: Timeout waiting for hardware interrupt" (LP: #1921140)
+    - SAUCE: mmc: host: Add required callbacks to set/clear CQE_EN bit
+
+  * Enable ath11k debugfs/tracing (LP: #1922033)
+    - [Config] enable ath11k debugfs/tracing
+
+  * Fix mic on P620 after S3 resume (LP: #1921757)
+    - ALSA: usb-audio: Carve out connector value checking into a helper
+    - ALSA: usb-audio: Check connector value on resume
+
+  * Miscellaneous Ubuntu changes
+    - [Config] amd64,arm64: build KFENCE support but disable it by default
+      (KFENCE_SAMPLE_INTERVAL=0)
+    - Rebase to v5.12-rc6
+
+  * Miscellaneous upstream changes
+    - drm/dp: add MSO related DPCD registers
+    - drm/i915/edp: reject modes with dimensions other than fixed mode
+    - drm/i915/edp: always add fixed mode to probed modes in ->get_modes()
+    - drm/i915/edp: read sink MSO configuration for eDP 1.4+
+    - drm/i915/reg: add stream splitter configuration definitions
+    - drm/i915/mso: add splitter state readout for platforms that support it
+    - drm/i915/mso: add splitter state check
+    - drm/i915/edp: modify fixed and downclock modes for MSO
+    - drm/i915/edp: enable eDP MSO during link training
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc6
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Wed, 07 Apr 2021 11:42:55 +0200
+
+linux-unstable (5.12.0-5.5) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * alsa/realtek: extend the delay time in the  determine_headset_type for a
+    Dell AIO (LP: #1920747)
+    - SAUCE: ALSA: hda/realtek: fix a determine_headset_type issue for a Dell AIO
+
+  * power off stress test will hang on the TGL machines (LP: #1919930)
+    - SAUCE: ASoC: SOF: Intel: TGL: set shutdown callback to hda_dsp_shutdown
+    - [Config] set SND_SOC_SOF_HDA_ALWAYS_ENABLE_DMI_L1 to n
+
+  * lockdown on power (LP: #1855668)
+    - SAUCE: (lockdown) powerpc: lock down kernel in secure boot mode
+
+  * Miscellaneous Ubuntu changes
+    - [Config] arm64 -- unify build_image and kernel_file values
+    - SAUCE: (lockdown) Add efi_status_to_str() and rework efi_status_to_err().
+    - SAUCE: (lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (lockdown) security: lockdown: expose a hook to lock the kernel down
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot
+      mode
+    - SAUCE: (lockdown) efi: Lock down the kernel if booted in secure boot mode
+    - SAUCE: (lockdown) s390: Lock down the kernel when the IPL secure flag is set
+    - SAUCE: (lockdown) KEYS: Make use of platform keyring for module signature
+      verify
+    - SAUCE: (lockdown) arm64: Allow locking down the kernel under EFI secure boot
+    - SAUCE: (lockdown) security: lockdown: Make
+      CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic
+    - SAUCE: xr-usb-serial: clean up indentation
+    - SAUCE: xr-usb-serial: clean up build warnings
+    - SAUCE: apparmor: Fix build error, make sk parameter const
+    - Rebase to v5.12-rc5
+    - [Config] updateconfigs following v5.12-rc5 rebase
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: (lockdown) s390: Lock down the kernel when the IPL
+      secure flag is set"
+    - Revert "UBUNTU: SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to
+      indicate secure boot mode"
+    - Revert "UBUNTU: SAUCE: (lockdown) powerpc: lock down kernel in secure boot
+      mode"
+    - Revert "UBUNTU: SAUCE: (lockdown) security: lockdown: Make
+      CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic"
+    - Revert "UBUNTU: SAUCE: (lockdown) arm64: Allow locking down the kernel under
+      EFI secure boot"
+    - Revert "UBUNTU: SAUCE: (lockdown) KEYS: Make use of platform keyring for
+      module signature verify"
+    - Revert "UBUNTU: SAUCE: (lockdown) efi: Lock down the kernel if booted in
+      secure boot mode"
+    - Revert "UBUNTU: SAUCE: (lockdown) security: lockdown: expose a hook to lock
+      the kernel down"
+    - Revert "UBUNTU: SAUCE: (lockdown) Make get_cert_list() use
+      efi_status_to_str() to print error messages."
+    - Revert "UBUNTU: SAUCE: (lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err()."
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc5
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 29 Mar 2021 12:59:38 +0200
+
+linux-unstable (5.12.0-4.4) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Fix broken efifb on graphics device without driver (LP: #1914411)
+    - SAUCE: efifb: Ensure graphics device for efifb stays at PCI D0
+
+  * Fix system sleep on TGL systems with Intel ME (LP: #1919321)
+    - SAUCE: PCI: Serialize TGL e1000e PM ops
+
+  * Miscellaneous Ubuntu changes
+    - Rebase to v5.12-rc4
+    - [Config] updateconfigs following v5.12-rc4 rebase
+
+  * Miscellaneous upstream changes
+    - riscv: dts: fu740: fix cache-controller interrupts
+    - riscv: sifive: fu740: cpu{1, 2, 3, 4} set compatible to sifive, u74-mc
+    - riscv: sifive: unmatched: update for 16GB rev3
+    - riscv: Add 3 SBI wrapper functions to get cpu manufacturer information
+    - riscv: Get CPU manufacturer information
+    - riscv: Introduce alternative mechanism to apply errata solution
+    - riscv: sifive: apply errata "cip-453" patch
+    - clk: sifive: Add pcie_aux clock in prci driver for PCIe driver
+    - clk: sifive: Use reset-simple in prci driver for PCIe driver
+    - MAINTAINERS: Add maintainers for SiFive FU740 PCIe driver
+    - dt-bindings: PCI: Add SiFive FU740 PCIe host controller
+    - PCI: designware: Add SiFive FU740 PCIe host controller driver
+    - riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc4
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 22 Mar 2021 12:43:14 +0100
+
+linux-unstable (5.12.0-3.3) hirsute; urgency=medium
+
+  *  riscv: revert SiFive Unleashed CPUFreq (LP: #1917433)
+    - SAUCE: Revert "SiFive Unleashed CPUFreq"
+
+  * Dell Precision 5550 takes up to 10 seconds to respond when coming out of
+    sleep (LP: #1919123)
+    - SAUCE: Input: i8042 - add dmi quirk
+
+  * LRMv4: switch to signing nvidia modules via the Ubuntu Modules signing key
+    (LP: #1918134)
+    - [Packaging] sync dkms-build et al from LRMv4
+
+  * curtin: install flash-kernel in arm64 UEFI unexpected (LP: #1918427)
+    - [Packaging] Allow grub-efi-arm* to satisfy recommends on ARM
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Enable Tegra support in arm64 for NVIDIA Jetson (LP: #1918471)
+    - [Config] enable ARCH_TEGRA and all Tegra SOC's
+    - [Packaging] include modern Tegra modules
+
+  * Cirrus Audio Codec CS8409/CS42L42: Input Device does not switch to headset
+    Mic when a headset is inserted (LP: #1918378)
+    - SAUCE: ALSA: hda/cirrus: Fix Headset Mic volume control name
+
+  * Cirrus Audio Codec CS8409/CS42L42 support (LP: #1916554)
+    - ALSA: hda/cirrus: Increase AUTO_CFG_MAX_INS from 8 to 18
+    - ALSA: hda/cirrus: Add support for CS8409 HDA bridge and CS42L42 companion
+      codec.
+    - ALSA: hda/cirrus: Add jack detect interrupt support from CS42L42 companion
+      codec.
+    - ALSA: hda/cirrus: Add Headphone and Headset MIC Volume Control
+
+  * drm/i915: Drop force_probe requirement for JSL (LP: #1917843)
+    - SAUCE: drm/i915: Drop require_force_probe from JSL
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Skip d-i code if udebs are disabled
+    - [Packaging] Disable udebs if $DEBIAN/d-i doesn't exist
+    - [Packaging] remove dh-systemd build dependency
+    - [Config] fix several annotaions with enforcement typos
+    - [Config] refresh annotations
+    - [Config] updateconfigs following v5.12-rc3 rebase
+    - annotations: fixup after v5.12-rc3 rebase
+    - Rebase to v5.12-rc3
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc3
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 16 Mar 2021 18:43:03 +0100
+
+linux-unstable (5.12.0-2.2) hirsute; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - Rebase to v5.12-rc2
+    - [Config] updateconfigs following v5.12-rc2 rebase
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc2
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 08 Mar 2021 11:22:04 +0100
+
+linux-unstable (5.12.0-1.1) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Support no udeb profile (LP: #1916095)
+    - [Packaging] replace custom filter script with dctrl-tools
+    - [Packaging] correctly implement noudeb build profiles.
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] dkms-versions -- remove nvidia-graphics-drivers-440-server
+    - [Debian] run ubuntu-regression-suite for linux-unstable
+    - [Packaging] remove Provides: aufs-dkms
+    - [Config] update config and annotations following v5.12-rc1 rebase
+    - [Config] disable nvidia and nvidia_server builds
+    - [Config] temporarily disable ZFS
+    - temporarily disable modules check
+    - annotations: s390: temporarily remove CONFIG_KMSG_IDS
+    - [Config] amd64: FTBFS: disable HIO
+    - [Config] FTBFS: disable SHIFT_FS
+    - [Config] s390: temporarily remove CONFIG_KMSG_IDS
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] disable nvidia and nvidia_server builds"
+    - Revert "UBUNTU: SAUCE: s390: kernel message catalog"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.12-rc1
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 04 Mar 2021 18:26:12 +0100
+
+linux-unstable (5.12.0-0.0) hirsute; urgency=medium
+
+  * Empty entry
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 04 Mar 2021 18:17:32 +0100
+
+linux-unstable (5.11.0-10.11) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+
+  * Support CML-S CPU + TGP PCH (LP: #1909457)
+    - drm/i915/rkl: new rkl ddc map for different PCH
+    - SAUCE: drm/i915/gen9_bc : Add TGP PCH support
+
+  * Use DCPD to control HP DreamColor panel (LP: #1911001)
+    - SAUCE: drm/dp: Another HP DreamColor panel brigntness fix
+
+  * Update nvidia dkms build for module linker script changes
+    - [Packaging] build-dkms--nvidia-N -- Update for preprocessed module linker
+      script
+
+  * Please trust Canonical Livepatch Service kmod signing key (LP: #1898716)
+    - [Config] enable CONFIG_MODVERSIONS=y
+    - [Packaging] build canonical-certs.pem from branch/arch certs
+    - [Config] add Canonical Livepatch Service key to SYSTEM_TRUSTED_KEYS
+    - [Config] add ubuntu-drivers key to SYSTEM_TRUSTED_KEYS
+
+  * Miscellaneous Ubuntu changes
+    - [Config] re-enable nvidia dkms
+    - SAUCE: selftests: memory-hotplug: bump timeout to 10min
+    - [Debian] update-aufs.sh -- Don't apply tmpfs-idr.patch
+    - [Config] Update configs
+    - [Config] disable nvidia and nvidia_server builds
+    - SAUCE: Import aufs driver
+    - [Config] CONFIG_AUFS_FS=n
+    - [Config] refresh annotations file
+    - [Config] set CONFIG_MIPI_I3C_HCI=m consistently
+    - [Config] set CONFIG_PINCTRL_MSM8953=m on armhf generic-lpae
+    - [Packaging] Change source package name to linux-unstable
+    - [Config] update LD_VERSION in config due to toolchain update
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: tmpfs: Don't use 64-bit inodes by defulat with 32-bit
+      ino_t"
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 22 Feb 2021 07:18:07 +0100
+
+linux-unstable (5.11.0-9.10) hirsute; urgency=medium
+
+  * Empty entry
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 22 Feb 2021 07:02:45 +0100
+
+linux (5.11.0-9.10) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Config] update configs/annotations after rebase to 5.11
+    - zfs-modules.ignore: add zzstd
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 15 Feb 2021 16:29:36 +0100
+
+linux (5.11.0-8.9) hirsute; urgency=medium
+
+  * Missing device id for Intel TGL-H ISH [8086:43fc] in intel-ish-hid driver
+    (LP: #1914543)
+    - SAUCE: HID: intel-ish-hid: ipc: Add Tiger Lake H PCI device ID
+
+  *  Add support for new Realtek ethernet NIC (LP: #1914604)
+    - r8169: Add support for another RTL8168FP
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: tmpfs: Don't use 64-bit inodes by defulat with 32-bit ino_t
+    - [Config] Set CONFIG_TMPFS_INODE64=n for s390x
+    - [Config] re-enable ZFS
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc7
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 08 Feb 2021 11:56:23 +0100
+
+linux (5.11.0-7.8) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  *  Boot fails: failed to validate module [nls_iso8859_1] BTF: -22
+    (LP: #1911359)
+    - SAUCE: x86/entry: build thunk_$(BITS) only if CONFIG_PREEMPTION=y
+
+  * Remove scary stack trace from Realtek WiFi driver (LP: #1913263)
+    - rtw88: reduce the log level for failure of tx report
+
+  * Fix unexpected AER/DPC on PCH400 and PCH500 (LP: #1913691)
+    - Revert "UBUNTU: SAUCE: PCI: Enable ACS quirk on all CML root ports"
+    - Revert "UBUNTU: SAUCE: PCI: Enable ACS quirk on CML root port"
+    - SAUCE: PCI/AER: Disable AER interrupt during suspend
+    - SAUCE: PCI/DPC: Disable DPC interrupt during suspend
+
+  * switch to an autogenerated nvidia series based core via dkms-versions
+    (LP: #1912803)
+    - [Packaging] nvidia -- use dkms-versions to define versions built
+    - [Packaging] update-version-dkms -- maintain flags fields
+
+  * Introduce the new NVIDIA 460-server series and update the 460 series
+    (LP: #1913200)
+    - [Config] dkms-versions -- add the 460-server nvidia driver
+
+  * Fix the video can't output through WD19TB connected with TGL platform during
+    cold-boot (LP: #1910211)
+    - SAUCE: drm/i915/dp: Prevent setting LTTPR mode if no LTTPR is detected
+
+  * Stop using get_scalar_status command in Dell AIO uart backlight driver
+    (LP: #1865402)
+    - SAUCE: platform/x86: dell-uart-backlight: add get_display_mode command
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests/seccomp: Accept any valid fd in user_notification_addfd
+    - [Packaging] Don't disable CONFIG_DEBUG_INFO in headers packages
+    - [Config] update configs/annotations after rebase to 5.11-rc6
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 01 Feb 2021 10:27:52 +0100
+
+linux (5.11.0-6.7) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Prevent thermal shutdown during boot process (LP: #1906168)
+    - thermal/drivers/acpi: Use hot and critical ops
+    - thermal/core: Remove notify ops
+    - thermal: int340x: Fix unexpected shutdown at critical temperature
+    - thermal: intel: pch: Fix unexpected shutdown at critical temperature
+
+  * riscv: backport support for SiFive Unmatched (LP: #1910965)
+    - RISC-V: Update l2 cache DT documentation to add support for SiFive FU740
+    - RISC-V: sifive_l2_cache: Update L2 cache driver to support SiFive FU740
+    - dt-bindings: riscv: Update DT binding docs to support SiFive FU740 SoC
+    - riscv: dts: add initial support for the SiFive FU740-C000 SoC
+    - dt-bindings: riscv: Update YAML doc to support SiFive HiFive Unmatched board
+    - riscv: dts: add initial board data for the SiFive HiFive Unmatched
+    - PCI: microsemi: Add host driver for Microsemi PCIe controller
+    - Microsemi PCIe expansion board DT entry.
+    - SiFive Unleashed CPUFreq
+    - SiFive HiFive Unleashed: Add PWM LEDs (D1, D2, D3, D4)
+
+  * initramfs unpacking failed (LP: #1835660)
+    - lib/decompress_unlz4.c: correctly handle zero-padding around initrds.
+
+  * Miscellaneous Ubuntu changes
+    - [Config] update configs and annotations after rebase to 5.11-rc5
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 25 Jan 2021 09:31:31 +0100
+
+linux (5.11.0-5.6) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Config] update config and annotations after rebase to 5.11-rc4
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc4
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 18 Jan 2021 10:46:10 +0100
+
+linux (5.11.0-4.5) hirsute; urgency=medium
+
+  *  Boot fails: failed to validate module [nls_iso8859_1] BTF: -22
+    (LP: #1911359)
+    - SAUCE: x86/entry: build thunk_$(BITS) only if CONFIG_PREEMPTION=y
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 14 Jan 2021 12:53:26 +0100
+
+linux (5.11.0-3.4) hirsute; urgency=medium
+
+  *  Boot fails: failed to validate module [nls_iso8859_1] BTF: -22
+    (LP: #1911359)
+    - bpf: Allow empty module BTFs
+    - libbpf: Allow loading empty BTFs
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 14 Jan 2021 07:43:45 +0100
+
+linux (5.11.0-2.3) hirsute; urgency=medium
+
+  * DMI entry syntax fix for Pegatron / ByteSpeed C15B (LP: #1910639)
+    - Input: i8042 - unbreak Pegatron C15B
+
+  * SYNA30B4:00 06CB:CE09 Mouse  on HP EliteBook 850 G7 not working at all
+    (LP: #1908992)
+    - HID: multitouch: Enable multi-input for Synaptics pointstick/touchpad device
+
+  * debian/scripts/file-downloader does not handle positive failures correctly
+    (LP: #1878897)
+    - [Packaging] file-downloader not handling positive failures correctly
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * CVE-2021-1052 // CVE-2021-1053
+    - [Packaging] NVIDIA -- Add the NVIDIA 460 driver
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Remove nvidia-455 dkms build
+    - SAUCE: ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP
+      machines
+    - [Config] update configs and annotations after rebase to 5.11-rc3
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc3
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 11 Jan 2021 09:52:27 +0100
+
+linux (5.11.0-1.2) hirsute; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc2
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 07 Jan 2021 16:57:01 +0100
+
+linux (5.11.0-0.1) hirsute; urgency=medium
+
+  * dep-8 ubuntu-regression-suite tests are not run for all linux-hwe-* kernels
+    (LP: #1908529)
+    - [dep-8] Allow all hwe kernels
+
+  * Fix reading speed and duplex sysfs on igc device (LP: #1906851)
+    - igc: Report speed and duplex as unknown when device is runtime suspended
+
+  * rtwpci driver blocks the system to enter PC10, stuck at PC3 (LP: #1907200)
+    - SAUCE: rtw88: 8723de: let cpu enter c10
+
+  * [21.04 FEAT] Deactivate CONFIG_QETH_OSN kernel config option (LP: #1906370)
+    - [Config] Deactivate CONFIG_QETH_OSN kernel config option
+
+  * Add dpcd backlight control for 0x4c83 0x4f41 (LP: #1905663)
+    - SAUCE: drm/dp: Add dpcd backlight control for 0x4c83 0x4f41
+
+  * disable building bpf selftests (LP: #1908144)
+    - SAUCE: selftests/bpf: Clarify build error if no vmlinux
+    - SAUCE: selftests: Skip BPF selftests by default
+    - disable building bpf selftests (no VMLINUX_BTF)
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot
+      mode
+    - SAUCE: (lockdown) s390: Lock down the kernel when the IPL secure flag is set
+    - [Config] update configs and annotations after rebase to v5.11-rc1
+    - hio: fix build error with kernel 5.11
+    - SAUCE: shiftfs: fix build error with 5.11
+    - [Config] temporarily disable ZFS
+    - check-aliases: do not error if modules.alias does not exist
+    - ppc64el: don't build stripped vdso
+
+  * Miscellaneous upstream changes
+    - irq: export irq_check_status_bit
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.11-rc1
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 04 Jan 2021 09:17:48 +0100
+
+linux (5.11.0-0.0) hirsute; urgency=medium
+
+  * Empty entry
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 30 Dec 2020 09:04:41 +0100
+
+linux (5.10.0-9.10) hirsute; urgency=medium
+
+  * Use INTx for Pericom USB controllers (LP: #1906839)
+    - PCI: Disable MSI for Pericom PCIe-USB adapter
+
+  * disable building bpf selftests (LP: #1908144)
+    - SAUCE: selftests/bpf: clarify build error if no vmlinux
+    - SAUCE: selftests: Skip BPF seftests by default
+    - disable building bpf selftests (no VMLINUX_BTF)
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enable CONFIG_BPF_LSM
+
+  * Miscellaneous upstream changes
+    - Revert "md: change mddev 'chunk_sectors' from int to unsigned"
+    - Revert "dm raid: fix discard limits for raid1 and raid10"
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 15 Dec 2020 10:16:14 +0100
+
+linux (5.10.0-8.9) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+
+  * Fix bpf selftest compilation with clang 11
+    - bpf: Fix selftest compilation on clang 11
+
+  * Miscellaneous Ubuntu changes
+    - [Config] update configs and annotations after rebase to v5.10
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 14 Dec 2020 08:57:57 +0100
+
+linux (5.10.0-7.8) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Fix linux-libc-dev build for hirsute forward port kernels (LP: #1904067)
+    - [Debian] Build linux-libc-dev for debian.master* branches
+
+  * Update kernel packaging to support forward porting kernels (LP: #1902957)
+    - [Debian] Update for leader included in BACKPORT_SUFFIX
+
+  * Introduce the new NVIDIA 455 series (LP: #1897751)
+    - [Packaging] NVIDIA -- Add signed modules for the 455 driver
+
+  * 5.10 kernel fails to boot with secure boot disabled (LP: #1904906)
+    - [Config] CONFIG_RCU_SCALE_TEST=n
+
+  * Miscellaneous Ubuntu changes
+    - [Config] s390x: disable GPIO_CDEV
+    - [Config] ARM_CMN=m
+    - [Config] disable GPIO_CDEV_V1
+    - [Config] Reorder annotations after 5.10-rc6 rebase
+    - [Packaging] Remove nvidia-435 dkms build
+    - [Packaging] Change source package name to linux
+    - [Config] Update configs and annotations after rebase to v5.10-rc7
+    - SAUCE: Revert "mm/filemap: add static for function
+      __add_to_page_cache_locked"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 07 Dec 2020 00:15:20 -0600
+
+linux (5.10.0-6.7) hirsute; urgency=medium
+
+  * Empty entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 06 Dec 2020 22:13:46 -0600
+
+linux-5.10 (5.10.0-6.7) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Avoid double newline when running insertchanges (LP: #1903293)
+    - [Packaging] insertchanges: avoid double newline
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging]: linux-modules should depend on linux-image
+    - [Packaging]: linux-image should suggest linux-modules-extra
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 30 Nov 2020 07:47:34 +0100
+
+linux-5.10 (5.10.0-5.6) hirsute; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] add CONFIG_INFINIBAND_VIRT_DMA
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 23 Nov 2020 13:17:44 +0100
+
+linux-5.10 (5.10.0-4.5) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] reduce the size required to build packages
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc4
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 16 Nov 2020 08:33:54 +0100
+
+linux-5.10 (5.10.0-3.4) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * e1000e: fix issues with S0ix (LP: #1902687)
+    - SAUCE: e1000e: fix S0ix flow to allow S0i3.2 subset entry
+    - SAUCE: e1000e: allow turning s0ix flows on for systems with ME
+    - SAUCE: e1000e: Add Dell's Comet Lake systems into s0ix heuristics
+    - SAUCE: e1000e: Add more Dell CML systems into s0ix heuristics
+    - [Config] Update CONFIG_E1000E for ppc64el in annotations
+
+  * perf: Add support for Rocket Lake (LP: #1902004)
+    - SAUCE: perf/x86/intel: Add Rocket Lake CPU support
+    - SAUCE: perf/x86/cstate: Add Rocket Lake CPU support
+    - SAUCE: perf/x86/msr: Add Rocket Lake CPU support
+    - SAUCE: perf/x86/intel/uncore: Add Rocket Lake support
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Disable CONFIG_CRYPTO_USER_API_ENABLE_OBSOLETE
+    - [Config] update CONFIG_MST_IRQ after rebase to 5.10-rc3
+    - [Config] drop obsolete SND_SST_IPC options
+    - [Config] re-enable ZFS
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc3
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 09 Nov 2020 09:37:08 +0100
+
+linux-5.10 (5.10.0-2.3) hirsute; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Switch arm64 default cpufreq governor to ondemand
+    - [Debian] Include scripts/module.lds from builddir in headers package
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 03 Nov 2020 21:01:52 -0600
+
+linux-5.10 (5.10.0-1.2) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Fix non-working Intel NVMe after S3 (LP: #1900847)
+    - SAUCE: PCI: Enable ACS quirk on all CML root ports
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] move to hirsute
+    - [Config] Update configs and annotations after rebase to 5.10-rc2
+    - [Config] Update numerous configs to conform with policy
+    - [Config] Switch default CPUFreq governer for arm64/armhf to schedultil
+    - [Config] Temporarily disable DEBUG_INFO_BTF for armhf
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 02 Nov 2020 13:18:27 -0600
+
+linux-5.10 (5.10.0-0.1) hirsute; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs and annotations for v5.10-rc1
+    - SAUCE: platform/x86: dell-uart-backlight: rename kzfree() to
+      kfree_sensitive()
+    - SAUCE: apparmor: rename kzfree() to kfree_sensitive()
+    - SAUCE: LSM: change ima_read_file() to use lsmblob
+    - SAUCE: LSM: Use lsmblob in smk_netlbl_mls()
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Packaging] Change source package name to linux-5.10"
+    - s390: correct __bootdata / __bootdata_preserved macros
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.10-rc1
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 27 Oct 2020 16:57:07 +0100
+
+linux-5.10 (5.10.0-0.0) groovy; urgency=medium
+
+  * Empty entry
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 26 Oct 2020 14:55:48 +0100
+
+linux-5.9 (5.9.0-2.3) groovy; urgency=medium
+
+  * Fix system reboot when disconnecting WiFi (LP: #1899726)
+    - iwlwifi: msix: limit max RX queues for 9000 family
+
+  * booting linux-generic-lpae armhf kernel under qemu results in relocation out
+    of range, and thus no modules can be loaded (LP: #1899519)
+    - [Config] armhf: ARM_MODULE_PLTS=y
+
+  * Fix broken MSI interrupt after HDA controller was suspended (LP: #1899586)
+    - ALSA: hda: fix jack detection with Realtek codecs when in D3
+
+  * CVE-2020-16119
+    - SAUCE: dccp: avoid double free of ccid on child socket
+
+  * python3-venv is gone (LP: #1896801)
+    - SAUCE: doc: remove python3-venv dependency
+
+  * *-tools-common packages descriptions have typo "PGKVER" (LP: #1898903)
+    - [Packaging] Fix typo in -tools template s/PGKVER/PKGVER/
+
+  * Enable brightness control on HP DreamColor panel (LP: #1898865)
+    - SAUCE: drm/i915/dpcd_bl: Skip testing control capability with force DPCD
+      quirk
+    - SAUCE: drm/dp: HP DreamColor panel brigntness fix
+
+  * HP Zbook Studio G7 boots into corrupted screen with PSR featured panel
+    (LP: #1897501)
+    - SAUCE: drm/i915/psr: allow overriding PSR disable param by quirk
+    - SAUCE: drm/dp: add DP_QUIRK_FORCE_PSR_CHIP_DEFAULT quirk to CMN prod-ID
+      19-15
+
+  * Fix broken e1000e device after S3 (LP: #1897755)
+    - SAUCE: e1000e: Increase polling timeout on MDIC ready bit
+
+  * Wakeup the system by touching the touchpad (LP: #1888331)
+    - HID: i2c-hid: Enable wakeup capability from Suspend-to-Idle
+
+  * Enable LTR for endpoints behind VMD (LP: #1896598)
+    - SAUCE: PCI/ASPM: Enable LTR for endpoints behind VMD
+
+  * [SRU] [Focal/OEM-5.6/Groovy]Fix AMD usb host controller lost after stress S3
+    (LP: #1893914)
+    - SAUCE: xhci: workaround for S3 issue on AMD SNPS 3.0 xHC
+
+  * debian/rules editconfigs does not work on s390x to change s390x only configs
+    (LP: #1863116)
+    - [Packaging] kernelconfig -- only update/edit configurations on architectures
+      we have compiler support
+
+  * Fix non-working NVMe after S3 (LP: #1895718)
+    - SAUCE: PCI: Enable ACS quirk on CML root port
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: bpf: Check CONFIG_BPF option for resolve_btfids
+    - SAUCE: tools resolve_btfids: Always force HOSTARCH
+    - packaging: arm64: add a 64KB mem pages flavour called 'generic-64k'
+    - packaging: arm64: generic-64k: skip ABI, modules and retpoline checks
+    - SAUCE: drm/i915/display: Fix null deref in intel_psr_atomic_check()
+    - [Config] Update toolchain versions
+    - [Config] Refresh annotations
+    - Add ubuntu-host module
+    - CONFIG_UBUNTU_HOST=m
+    - SAUCE: apparmor: drop prefixing abs root labels with '='
+    - SAUCE: apparmor: disable showing the mode as part of a secid to secctx
+    - SAUCE: apparmor: rename aa_sock() to aa_unix_sk()
+    - SAUCE: apparmor: LSM stacking: switch from SK_CTX() to aa_sock()
+    - SAUCE: LSM: Infrastructure management of the sock security
+    - SAUCE: LSM: Create and manage the lsmblob data structure.
+    - SAUCE: LSM: Use lsmblob in security_audit_rule_match
+    - SAUCE: LSM: Use lsmblob in security_kernel_act_as
+    - SAUCE: net: Prepare UDS for security module stacking
+    - SAUCE: LSM: Use lsmblob in security_secctx_to_secid
+    - SAUCE: LSM: Use lsmblob in security_secid_to_secctx
+    - SAUCE: LSM: Use lsmblob in security_ipc_getsecid
+    - SAUCE: LSM: Use lsmblob in security_task_getsecid
+    - SAUCE: LSM: Use lsmblob in security_inode_getsecid
+    - SAUCE: LSM: Use lsmblob in security_cred_getsecid
+    - SAUCE: IMA: Change internal interfaces to use lsmblobs
+    - SAUCE: LSM: Specify which LSM to display
+    - SAUCE: LSM: Ensure the correct LSM context releaser
+    - SAUCE: LSM: Use lsmcontext in security_secid_to_secctx
+    - SAUCE: LSM: Use lsmcontext in security_inode_getsecctx
+    - SAUCE: LSM: security_secid_to_secctx in netlink netfilter
+    - SAUCE: NET: Store LSM netlabel data in a lsmblob
+    - SAUCE: LSM: Verify LSM display sanity in binder
+    - SAUCE: Audit: Add new record for multiple process LSM attributes
+    - SAUCE: Audit: Add a new record for multiple object LSM
+    - SAUCE: LSM: Add /proc attr entry for full LSM context
+    - SAUCE: AppArmor: Remove the exclusive flag
+    - SAUCE: Audit: Fix for missing NULL check
+
+  * Miscellaneous upstream changes
+    - tty: hvcs: Don't NULL tty->driver_data until hvcs_cleanup()
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.9
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 14 Oct 2020 13:31:18 -0500
+
+linux-5.9 (5.9.0-1.2) groovy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs after rebase to 5.9-rc6
+    - SAUCE: dax: Fix compilation for CONFIG_DAX && !CONFIG_FS_DAX
+    - SAUCE: bpf: Use --no-fail option if CONFIG_BPF is not enabled
+    - SAUCE: tools resolve_btfids: Always force HOSTARCH
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.9-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 21 Sep 2020 14:39:34 -0500
+
+linux-5.9 (5.9.0-0.1) groovy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs and annotations for v5.9-rc1
+    - SAUCE: i915: Fix build error due to missing struct definition
+    - hio -- Update blk_queue_split() calls for changes in 5.9-rc1
+    - hio -- Updates for move of make_request_fn to struct block_device_operations
+    - [Config] Disable zfs dkms build
+    - [Config] Disable nvidia dkms build
+    - [Config] Disable nvidia server dkms builds
+    - SAUCE: remoteproc: qcom: Use div_u64() for 64-bit division
+    - SAUCE: PCI/ASPM: Enable ASPM for links under VMD domain
+    - [Packaging] Bind hv_vss_daemon startup to hv_vss device
+    - [Packaging] bind hv_fcopy_daemon startup to hv_fcopy device
+    - [Config] Re-enable UEFI signing for arm64
+    - SAUCE: Revert "UBUNTU: SAUCE: export __get_vm_area_caller() and map_kernel_range()"
+    - [Config] Set the default CPU governor to ONDEMAND
+    - [Packaging] update variants
+    - [Packaging] update helper scripts
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.9-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 17 Sep 2020 15:01:21 -0500
+
+linux-5.9 (5.9.0-0.0) groovy; urgency=medium
+
+  * Empty entry
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 18 Aug 2020 16:48:03 -0500
+
+linux (5.8.0-16.17) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-16.17 -proposed tracker (LP: #1891233)
+
+  * Miscellaneous Ubuntu changes
+    - hio -- Update to use bio_{start,end}_io_acct with 5.8+
+    - Enable hio driver
+    - [Packaging] Temporarily disable building doc package contents
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 11 Aug 2020 15:32:58 -0500
+
+linux (5.8.0-15.16) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-15.16 -proposed tracker (LP: #1891177)
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Documentation: import error c_funcptr_sig_re, c_sig_re (sphinx-
+      doc/sphinx@0f49e30c)
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 11 Aug 2020 09:29:58 -0500
+
+linux (5.8.0-14.15) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-14.15 -proposed tracker (LP: #1891085)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * msg_zerocopy.sh in net from ubuntu_kernel_selftests failed (LP: #1812620)
+    - selftests/net: relax cpu affinity requirement in msg_zerocopy test
+
+  * Fix missing HDMI/DP Audio on an HP Desktop (LP: #1890441)
+    - ALSA: hda/hdmi: Add quirk to force connectivity
+
+  * Add initial audio support for Lenovo ThinkStation P620 (LP: #1890317)
+    - ALSA: usb-audio: Add support for Lenovo ThinkStation P620
+
+  * Fix IOMMU error on AMD Radeon Pro W5700 (LP: #1890306)
+    - PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken
+
+  * Enlarge hisi_sec2 capability (LP: #1890222)
+    - crypto: hisilicon - update SEC driver module parameter
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Re-enable signing for ppc64el
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 10 Aug 2020 15:26:46 -0500
+
+linux (5.8.0-13.14) groovy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Remove i386 configs
+    - SAUCE: apply a workaround to re-enable CONFIG_CRYPTO_AEGIS128_SIMD
+    - SAUCE: export __get_vm_area_caller() and map_kernel_range()
+    - [Config] drop CONFIG_BINFMT_AOUT enforcement
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] disable CONFIG_CRYPTO_AEGIS128_SIMD"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 04 Aug 2020 09:51:50 +0200
+
+linux (5.8.0-12.13) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-12.13 -proposed tracker (LP: #1889481)
+
+  * Fix right speaker of HP laptop (LP: #1889375)
+    - SAUCE: hda/realtek: Fix right speaker of HP laptop
+
+  * blk_update_request error when mount nvme partition (LP: #1872383)
+    - SAUCE: nvme-pci: prevent SK hynix PC400 from using Write Zeroes command
+
+  * Add support for Atlantic NIC firmware v4 (LP: #1886908)
+    - Revert "UBUNTU: SAUCE: net: atlantic: Add support for firmware v4"
+    - net: atlantic: align return value of ver_match function with function name
+    - net: atlantic: add support for FW 4.x
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Fix debian/tests for linux-5.8 -> linux rename
+    - SAUCE: selftests/powerpc: return skip code for spectre_v2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 29 Jul 2020 16:58:47 -0500
+
+linux (5.8.0-11.12) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-11.12 -proposed tracker (LP: #1889336)
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] dwarves is not required for linux-libc-dev or stage1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 28 Jul 2020 22:33:24 -0500
+
+linux (5.8.0-10.11) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-10.11 -proposed tracker (LP: #1889316)
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Add more packages to Build-Depends-Indep for docs
+    - [Debian] Specify python executable in kmake
+    - [Debian] Don't treat warnings as errors during perf builds
+    - [Config] Disable signing for ppc64el
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 28 Jul 2020 17:09:52 -0500
+
+linux (5.8.0-9.10) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-9.10 -proposed tracker (LP: #1889140)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Fix s390x compile error on F32 utils/stat-display.c
+    - [Packaging] Add python3-venv to Build-Depends-Indep
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 27 Jul 2020 21:01:46 -0500
+
+linux (5.8.0-8.9) groovy; urgency=medium
+
+  * groovy/linux: 5.8.0-8.9 -proposed tracker (LP: #1889104)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - update dkms package versions
+    - [Packaging] update variants
+
+  * Introduce the new NVIDIA 450-server and the 450 UDA series (LP: #1887674)
+    - [Packaging] NVIDIA -- Add signed modules for 450 450-server
+
+  * Introduce the new NVIDIA 418-server and 440-server series, and update the
+    current NVIDIA drivers (LP: #1881137)
+    - [packaging] add signed modules for the 418-server and the 440-server
+      flavours
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "radix-tree: Use local_lock for protection"
+    - [Config] CONFIG_DEBUG_INFO_COMPRESSED=n
+    - [Config] disable CONFIG_CRYPTO_AEGIS128_SIMD
+    - [Config] Enable nvidia dkms build
+
+  * Miscellaneous upstream changes
+    - usbip: tools: fix build error for multiple definition
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 27 Jul 2020 11:18:12 -0500
+
+linux (5.8.0-7.8) groovy; urgency=medium
+
+  * Empty entry
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 27 Jul 2020 09:22:19 +0200
+
+linux-5.8 (5.8.0-7.8) groovy; urgency=medium
+
+  * soc/amd/renoir: detect dmic from acpi table (LP: #1887734)
+    - ASoC: amd: add logic to check dmic hardware runtime
+    - ASoC: amd: add ACPI dependency check
+    - ASoC: amd: fixed kernel warnings
+
+  * linux 4.15.0-109-generic network DoS regression vs -108 (LP: #1886668)
+    - SAUCE: Revert "netprio_cgroup: Fix unlimited memory leak of v2 cgroups"
+
+  * Add support for Atlantic NIC firmware v4 (LP: #1886908)
+    - SAUCE: net: atlantic: Add support for firmware v4
+
+  * MGA G200e doesn't work under GDM Wayland (LP: #1886140)
+    - drm/mgag200: Remove HW cursor
+    - drm/mgag200: Clean up mga_set_start_address()
+    - drm/mgag200: Clean up mga_crtc_do_set_base()
+    - drm/mgag200: Move mode-setting code into separate helper function
+    - drm/mgag200: Split MISC register update into PLL selection, SYNC and I/O
+    - drm/mgag200: Update mode registers after plane registers
+    - drm/mgag200: Set pitch in a separate helper function
+    - drm/mgag200: Set primary plane's format in separate helper function
+    - drm/mgag200: Move TAGFIFO reset into separate function
+    - drm/mgag200: Move hiprilvl setting into separate functions
+    - drm/mgag200: Move register initialization into separate function
+    - drm/mgag200: Remove out-commented suspend/resume helpers
+    - drm/mgag200: Use simple-display data structures
+    - drm/mgag200: Convert to simple KMS helper
+    - drm/mgag200: Replace VRAM helpers with SHMEM helpers
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: s390/bpf: fix sign extension in branch_ku
+    - SAUCE: selftests: net: ip_defrag: modprobe missing nf_defrag_ipv6 support
+    - SAUCE: selftests: fib_nexthop_multiprefix: fix cleanup() netns deletion
+    - [packaging] debhelper-compat (= 10) (and retire debian/compat)
+    - [Config] Update configs after rebase to 5.8-rc6
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 20 Jul 2020 09:55:47 +0200
+
+linux-5.8 (5.8.0-6.7) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * perf build broken after updating to bintuils 2.34.90.20200706-1ubuntu1
+    (LP: #1887397)
+    - SAUCE: libtraceevent: Strip symbol version from nm output
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 13 Jul 2020 14:07:53 -0500
+
+linux-5.8 (5.8.0-5.6) groovy; urgency=medium
+
+  * linux-libc-dev broken for crossbuilding, Multi-Arch:same violation
+    (LP: #1886188)
+    - [Packaging] Produce linux-libc-deb package for riscv64
+    - [Debian] Disallow building linux-libc-dev from linux-riscv
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "UBUNTU: SAUCE: test_bpf: remove expected fail for Ctx heavy
+      transformations test on s390"
+    - SAUCE: Revert "test_bpf: flag tests that cannot be jited on s390"
+    - [Config] Update configs (gcc update)
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 13 Jul 2020 08:42:14 +0200
+
+linux-5.8 (5.8.0-4.5) groovy; urgency=medium
+
+  * Add generic LED class support for audio LED (LP: #1885896)
+    - ALSA: hda: generic: Always call led-trigger for mic mute LED
+    - ALSA: hda: generic: Add a helper for mic-mute LED with LED classdev
+    - ALSA: hda/realtek: Convert to cdev-variant of mic-mute LED controls
+    - ALSA: hda/conexant: Convert to cdev-variant of mic-mute LED controls
+    - ALSA: hda/sigmatel: Convert to cdev-variant of mic-mute LED controls
+    - ALSA: hda: generic: Drop unused snd_hda_gen_fixup_micmute_led()
+    - ALSA: hda: generic: Drop the old mic-mute LED hook
+    - ALSA: hda: generic: Add vmaster mute LED helper
+    - ALSA: hda/realtek: Use the new vmaster mute LED helper
+    - ALSA: hda/conexant: Use the new vmaster mute LED helper
+    - ALSA: hda/sigmatel: Use the new vmaster mute LED helper
+    - ALSA: hda/realtek: Unify LED helper code
+    - ALSA: hda: Let LED cdev handling suspend/resume
+
+  * seccomp_bpf fails on powerpc (LP: #1885757)
+    - SAUCE: selftests/seccomp: fix ptrace tests on powerpc
+
+  * CVE-2020-11935
+    - SAUCE: aufs: do not call i_readcount_inc()
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Update aufs to 5.x-rcN 20200622
+    - [Config] Update configs to set CONFIG_SND_HDA_GENERIC_LEDS value
+    - [Config] CONFIG_SECURITY_DMESG_RESTRICT=y
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 06 Jul 2020 08:14:28 -0500
+
+linux-5.8 (5.8.0-3.4) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - update dkms package versions
+
+  * lxc 1:4.0.2-0ubuntu1 ADT test failure with linux-5.8 5.8.0-1.2
+    (LP: #1884635)
+    - SAUCE: overlayfs: fix faulty rebase
+
+  * shiftfs: O_TMPFILE reports ESTALE (LP: #1872757)
+    - SAUCE: shiftfs: prevent ESTALE for LOOKUP_JUMP lookups
+
+  * shiftfs: fix btrfs regression (LP: #1884767)
+    - SAUCE: Revert "UBUNTU: SAUCE: shiftfs: fix dentry revalidation"
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_DEBUG_INFO_COMPRESSED=y
+    - SAUCE: regulator: rename da903x to da903x-regulator
+    - [Config] Add da903x to modules.ignore
+    - [Config] Update configs for rebase to 5.8-rc3
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 29 Jun 2020 08:48:25 -0500
+
+linux-5.8 (5.8.0-2.3) groovy; urgency=medium
+
+  * Support Audio Mute LED for two new HP laptops (LP: #1884251)
+    - ALSA: hda/realtek: Add mute LED and micmute LED support for HP systems
+
+  * CVE-2019-16089
+    - SAUCE: nbd_genl_status: null check for nla_nest_start
+
+  * tpm: fix TIS locality timeout problems (LP: #1881710)
+    - SAUCE: tpm: fix TIS locality timeout problems
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: security,perf: Allow further restriction of perf_event_open
+    - [Config] CONFIG_SECURITY_PERF_EVENTS_RESTRICT=y
+    - [Config] Update configs and annotations for 5.8-rc2
+    - [Config] Enable zfs
+    - [Config] Enable CONFIG_DEBUG_INFO_BTF
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 22 Jun 2020 15:05:54 -0500
+
+linux-5.8 (5.8.0-1.2) groovy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Support linux-x.y in udeb package names
+    - [Packaging] Use SRCPKGNAME for udeb packages
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 17 Jun 2020 19:34:32 -0500
+
+linux-5.8 (5.8.0-0.1) groovy; urgency=medium
+
+  * Docker registry doesn't stay up and keeps restarting (LP: #1879690)
+    - Revert "UBUNTU: SAUCE: overlayfs: use shiftfs hacks only with shiftfs as underlay"
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Update source package name to linux-5.8
+    - SAUCE: (lockdown) Add efi_status_to_str() and rework efi_status_to_err().
+    - SAUCE: (lockdown) Make get_cert_list() use efi_status_to_str() to print error messages.
+    - SAUCE: (lockdown) security: lockdown: expose a hook to lock the kernel down
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot mode
+    - SAUCE: (lockdown) efi: Lock down the kernel if booted in secure boot mode
+    - SAUCE: (lockdown) s390: Lock down the kernel when the IPL secure flag is set
+    - SAUCE: (lockdown) KEYS: Make use of platform keyring for module signature verify
+    - SAUCE: (lockdown) arm64: Allow locking down the kernel under EFI secure boot
+    - SAUCE: (lockdown) security: lockdown: Make CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic
+    - SAUCE: (lockdown) powerpc: lock down kernel in secure boot mode
+    - SAUCE: Import aufs driver
+    - [Config] Update configs for v5.8-rc1
+    - [Config] Update annotations for v5.8-rc1 config changes
+    - SAUCE: shiftfs -- Fix build errors from missing fiemap definitions
+    - Disable hio driver
+
+  * Miscellaneous upstream changes
+    - acpi: disallow loading configfs acpi tables when locked down
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.8-rc1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 17 Jun 2020 11:54:24 -0500
+
+linux-5.8 (5.8.0-0.0) groovy; urgency=medium
+
+  * Empty entry
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 14 Jun 2020 22:40:35 -0500
+
+linux-5.7 (5.7.0-8.9) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Enforce all config annotations (LP: #1879327)
+    - [Config]: do not enforce CONFIG_VERSION_SIGNATURE
+    - [Config]: prepare to enforce all
+    - [Config]: enforce all config options
+
+  * Miscellaneous Ubuntu changes
+    - [Config]: annotations review after 5.7 rebase
+    - [Config] annotations: IXP4XX* depends on ARCH_IXP4XX
+    - [Config] THERMAL_GOV_POWER_ALLOCATOR=y
+    - [Config] annotations: SOC_CAMERA is marked as BROKEN
+    - [Config] annotations: NFSD_V4_2_INTER_SSC depends on NFS_FS=y
+    - [Config] annotations: CRYPTO_DEV_CHELSIO_TLS depends on legacy (and largely
+      unmantained) TLS_TOE
+    - [Config] annotations: SERIO_OLPC_APSP depends on ARCH_MMP
+    - [Config] RTW88_DEBUG=y
+    - [Config] annotations: ISDN_CAPI is a bool, and BT_CMTP depends on  it
+    - [Config] annotations SND_SOC_SOF_DEVELOPER_SUPPORT depends on
+      SND_SOC_SOF_DEVELOPER_SUPPORT
+    - [Config] annotations: SND_SOC_SOF_BAYTRAIL_SUPPORT is mutually exclusive
+      with SND_SST_ATOM_HIFI2_PLATFORM_ACPI
+    - [Config] annotations: DEBUG_IMX_UART_PORT is defined only any
+      DEBUG_IMX*_UART is enabled
+    - [Config] annotations: HW_RANDOM_IMX_RNGC depends on SOC_IMX25
+    - [Config] annotations: armhf: VIRTUALIZATION support was removed for arm32
+    - [Config] annotations: arm64: remove DEBUG_ALIGN_RODATA
+    - [Config] annotations: ppc64: DATA_SHIFT defaults to PPC_PAGE_SHIFT
+    - [Config] arm64: enforce ARM64_USE_LSE_ATOMICS
+    - [Config] s390x: MOST is not set
+    - [Config] s390x: BCM84881_PHY is not set
+    - [Config] s390x: XILINX_LL_TEMAC is not set
+    - [Config] s390x: PHY_INTEL_EMMC requires GENERIC_PHY (off by default on
+      s390x)
+    - [Config] s390x: CHECK_STACK conflicts with VMAP_STACK
+    - [Config] annotations: s390x: NODES_SHIFT=1
+    - [Config] annotations: import new symbols
+    - [Config] annotations: remove unmatched menu and options
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Fri, 12 Jun 2020 12:03:01 +0200
+
+linux-5.7 (5.7.0-7.8) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+    - [Packaging] update helper scripts
+
+  * [UBUNTU 20.04] s390x/pci: fix linking between PF and VF for multifunction
+    devices (LP: #1879704)
+    - PCI/IOV: Introduce pci_iov_sysfs_link() function
+    - s390/pci: create links between PFs and VFs
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Disable UEFI signing for arm64
+    - Rebase to v5.7.1
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.7.1
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 08 Jun 2020 11:16:58 +0200
+
+linux-5.7 (5.7.0-6.7) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - update dkms package versions
+
+  * shiftfs: fix btrfs snapshot deletion (LP: #1879688)
+    - SAUCE: shiftfs: let userns root destroy subvolumes from other users
+
+  * seccomp_benchmark times out on eoan (LP: #1881576)
+    - SAUCE: selftests/seccomp: use 90s as timeout
+
+  * Realtek 8723DE [10ec:d723] subsystem [10ec:d738]  disconnects unsolicitedly
+    when Bluetooth is paired: Reason: 23=IEEE8021X_FAILED (LP: #1878147)
+    - SAUCE: Revert "UBUNTU: SAUCE: rtw88: Move driver IQK to set channel before
+      association for 11N chip"
+    - SAUCE: Revert "UBUNTU: SAUCE: rtw88: fix rate for a while after being
+      connected"
+    - SAUCE: Revert "UBUNTU: SAUCE: rtw88: No retry and report for auth and assoc"
+    - SAUCE: Revert "UBUNTU: SAUCE: rtw88: 8723d: Add coex support"
+    - rtw88: 8723d: Add coex support
+    - SAUCE: rtw88: coex: 8723d: set antanna control owner
+    - SAUCE: rtw88: coex: 8723d: handle BT inquiry cases
+    - SAUCE: rtw88: fix EAPOL 4-way failure by finish IQK earlier
+
+  * ASoC/amd: add audio driver for amd renoir (LP: #1881046)
+    - ASoC: amd: add Renoir ACP3x IP register header
+    - ASoC: amd: add Renoir ACP PCI driver
+    - ASoC: amd: add acp init/de-init functions
+    - ASoC: amd: create acp3x pdm platform device
+    - ASoC: amd: add ACP3x PDM platform driver
+    - ASoC: amd: irq handler changes for ACP3x PDM dma driver
+    - ASoC: amd: add acp3x pdm driver dma ops
+    - ASoC: amd: add ACP PDM DMA driver dai ops
+    - ASoC: amd: add Renoir ACP PCI driver PM ops
+    - ASoC: amd: add ACP PDM DMA driver pm ops
+    - ASoC: amd: enable Renoir acp3x drivers build
+    - ASoC: amd: create platform devices for Renoir
+    - ASoC: amd: RN machine driver using dmic
+    - ASoC: amd: enable build for RN machine driver
+    - ASoC: amd: fix kernel warning
+    - ASoC: amd: refactoring dai_hw_params() callback
+    - ASoC: amd: return error when acp de-init fails
+    - [Config]: enable amd renoir ASoC audio
+
+  * Slow send speed with Intel I219-V on Ubuntu 18.04.1 (LP: #1802691)
+    - e1000e: Disable TSO for buffer overrun workaround
+
+  * Fix incorrect speed/duplex when I210 device is runtime suspended
+    (LP: #1880656)
+    - igb: Report speed and duplex as unknown when device is runtime suspended
+
+  * Fix Pericom USB controller OHCI/EHCI PME# defect (LP: #1879321)
+    - serial: 8250_pci: Move Pericom IDs to pci_ids.h
+    - PCI: Avoid Pericom USB controller OHCI/EHCI PME# defect
+
+  * [UBUNTU 20.04] s390x/pci: enumerate pci functions per physical adapter
+    (LP: #1874056)
+    - s390/pci: Expose new port attribute for PCIe functions
+    - s390/pci: adaptation of iommu to multifunction
+    - s390/pci: define kernel parameters for PCI multifunction
+    - s390/pci: define RID and RID available
+    - s390/pci: create zPCI bus
+    - s390/pci: adapt events for zbus
+    - s390/pci: Handling multifunctions
+    - s390/pci: Do not disable PF when VFs exist
+    - s390/pci: Documentation for zPCI
+    - s390/pci: removes wrong PCI multifunction assignment
+
+  * add 16-bit width registers support for EEPROM at24 device (LP: #1876699)
+    - regmap-i2c: add 16-bit width registers support
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enable virtualbox guest and shared-folder modules
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 01 Jun 2020 16:11:24 -0500
+
+linux-5.7 (5.7.0-5.6) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * [UBUNTU 20.04] PSI generates overhead on s390x (LP: #1876044)
+    - Ubuntu: [Config] CONFIG_PSI is enabled by default, but creates additional
+      overhead on s390x, hence should be disabled by default on s390x only.
+
+  * Miscellaneous Ubuntu changes
+    - Rebase to v5.7-rc7
+    - [Config] ppc64el: disable STRICT_KERNEL_RWX
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.7-rc7
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 25 May 2020 11:44:09 +0200
+
+linux-5.7 (5.7.0-4.5) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * update-initramfs complains of missing amdgpu firmware files (LP: #1873325)
+    - SAUCE: drm/amdgpu: Remove unreleased arcturus and navi12 firmware from
+      modinfo
+
+  * Support DMIC micmute LED on HP platforms (LP: #1876859)
+    - ALSA: hda/realtek - Introduce polarity for micmute LED GPIO
+    - ALSA: hda/realtek - Enable micmute LED on and HP system
+    - ALSA: hda/realtek - Add LED class support for micmute LED
+    - ALSA: hda/realtek - Fix unused variable warning w/o
+      CONFIG_LEDS_TRIGGER_AUDIO
+    - ASoC: SOF: Update correct LED status at the first time usage of
+      update_mute_led()
+
+  * Killer(R) Wi-Fi 6 AX1650i 160MHz Wireless Network Adapter (201NGW),
+    REV=0x354 [8086:a0f0] subsystem id [1a56:1651] wireless adapter not found
+    due to firmware crash (LP: #1874685)
+    - SAUCE: iwlwifi: pcie: handle QuZ configs with killer NICs as well
+
+  * rtkit-daemon[*]: Failed to make ourselves RT: Operation not permitted after
+    upgrade to 20.04 (LP: #1875665)
+    - [Config] Turn off CONFIG_RT_GROUP_SCHED everywhere
+
+  * Unable to handle kernel pointer dereference in virtual kernel address space
+    on Eoan (LP: #1876645)
+    - SAUCE: overlayfs: fix shitfs special-casing
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: skip building selftest 'runqslower' if kernel not built
+    - Rebase to v5.7-rc6
+    - [Config] updateconfigs after 5.7-rc6 rebase
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.7-rc6
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 18 May 2020 11:27:25 +0200
+
+linux-5.7 (5.7.0-3.4) groovy; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.7-rc5
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * getitimer returns it_value=0 erroneously (LP: #1349028)
+    - [Config] CONTEXT_TRACKING_FORCE policy should be unset
+
+  * lockdown on power (LP: #1855668) // Ubuntu Kernel Support for OpenPOWER NV
+    Secure & Trusted Boot (LP: #1866909)
+    - [Config] Enable configs for OpenPOWER NV Secure & Trusted Boot
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Import aufs driver
+    - [Config] Enable aufs
+    - [Config] annotations: remove SND_SOC_SOF_HDA_COMMON_HDMI_CODEC
+    - [Config] Remove CONFIG_SND_HDA_INTEL_DETECT_DMIC from annotations
+    - [Debian] final-checks -- Do not remove ~* from abi
+    - [Config] Enable 5-level page table support for x86
+    - [Config] updateconfigs after 5.7-rc5 rebase
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 11 May 2020 10:25:42 +0200
+
+linux-5.7 (5.7.0-2.3) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - update dkms package versions
+    - [Packaging] update helper scripts
+
+  * ASUS T100HAN boots to a blank screen with a cursor [i965: Failed to submit
+    batchbuffer: Input/output error] (LP: #1860754)
+    - [Config] CONFIG_PMIC_OPREGION=y and CONFIG_GPIO_CRYSTAL_COVE=y for amd64
+
+  * ubuntu/focal64 fails to mount Vagrant shared folders  (LP: #1873506)
+    - [Packaging] Move virtualbox modules to linux-modules
+    - [Packaging] Remove vbox and zfs modules from generic.inclusion-list
+
+  * built-using constraints preventing uploads (LP: #1875601)
+    - temporarily drop Built-Using data
+
+  * dkms artifacts may expire from the pool (LP: #1850958)
+    - [Packaging] autoreconstruct -- manage executable debian files
+    - [packaging] handle downloads from the librarian better
+
+  * Add signed modules for the 435 NVIDIA driver (LP: #1875888)
+    - [Packaging] NVIDIA -- add signed modules for the 435 NVIDIA driver
+
+  * [Selftests] Apply various fixes and improvements (LP: #1870543)
+    - SAUCE: selftests/seccomp -- Disable timeout for seccomp tests
+
+  * [17.04 FEAT] Integrate kernel message catalogue for s390x into Ubuntu
+    distribution (LP: #1628889)
+    - SAUCE: s390: kernel message catalog
+
+  * Overlayfs in user namespace leaks directory content of inaccessible
+    directories (LP: #1793458) // CVE-2018-6559
+    - SAUCE: overlayfs: ensure mounter privileges when reading directories
+
+  * suspend only works once on ThinkPad X1 Carbon gen 7 (LP: #1865570)
+    - SAUCE: e1000e: Disable s0ix flow for X1 Carbon 7th
+
+  * [ICL] TC port in legacy/static mode can't be detected due TCCOLD
+    (LP: #1868936)
+    - drm/i915/display: Move out code to return the digital_port of the aux ch
+    - drm/i915/display: Add intel_legacy_aux_to_power_domain()
+    - drm/i915/display: Split hsw_power_well_enable() into two
+    - drm/i915/tc/icl: Implement TC cold sequences
+    - drm/i915/tc: Skip ref held check for TC legacy aux power wells
+    - drm/i915/tc/tgl: Implement TC cold sequences
+    - drm/i915/tc: Catch TC users accessing FIA registers without enable aux
+    - drm/i915/tc: Do not warn when aux power well of static TC ports timeout
+
+  * Touchpad doesn't work on Dell Inspiron 7000 2-in-1 (LP: #1851901)
+    - Revert "UBUNTU: SAUCE: mfd: intel-lpss: add quirk for Dell XPS 13 7390
+      2-in-1"
+
+  * 'Elan touchpad' not detected on 'Lenovo ThinkBook 15 IIL' (LP: #1861610)
+    - SAUCE: Input: elan_i2c - add more hardware ID for Lenovo laptop
+
+  * linux-image-5.0.0-35-generic breaks checkpointing of container
+    (LP: #1857257)
+    - SAUCE: overlayfs: use shiftfs hacks only with shiftfs as underlay
+
+  * alsa/sof: kernel oops on the machine without Intel hdmi audio codec (a
+    regression in the  asoc machine driver) (LP: #1874359)
+    - ASoC: intel/skl/hda - fix oops on systems without i915 audio codec
+
+  * Add debian/rules targets to compile/run kernel selftests (LP: #1874286)
+    - [Packaging] add support to compile/run selftests
+
+  * 5.4.0-24.28 does not seem to apply rtprio, whereas -21 does. (LP: #1873315)
+    - [Config] lowlatency: turn off RT_GROUP_SCHED
+
+  * alsa/sof: external mic can't be deteced on Lenovo and HP laptops
+    (LP: #1872569)
+    - SAUCE: ASoC: intel/skl/hda - set autosuspend timeout for hda codecs
+
+  * shiftfs: O_TMPFILE reports ESTALE (LP: #1872757)
+    - SAUCE: shiftfs: fix dentry revalidation
+
+  * shiftfs: broken shiftfs nesting (LP: #1872094)
+    - SAUCE: shiftfs: record correct creator credentials
+
+  * lockdown on power (LP: #1855668)
+    - SAUCE: (lockdown) powerpc: lock down kernel in secure boot mode
+
+  * Add support for Realtek 8723DE wireless adapter (LP: #1780590)
+    - SAUCE: rtw88: add adaptivity support for EU/JP regulatory
+    - SAUCE: rtw88: update tx descriptor of mgmt and rsvd page packets
+    - SAUCE: rtw88: sar: dump sar information via debugfs
+    - SAUCE: rtw88: 8723d: add IQ calibration
+    - SAUCE: rtw88: 8723d: Add power tracking
+    - SAUCE: rtw88: 8723d: implement flush queue
+    - SAUCE: rtw88: 8723d: set ltecoex register address in chip_info
+    - SAUCE: rtw88: 8723d: Add coex support
+    - SAUCE: rtw88: 8723d: Add shutdown callback to disable BT USB suspend
+
+  * Fix authentication fail on Realtek WiFi 8723de (LP: #1871300)
+    - SAUCE: rtw88: No retry and report for auth and assoc
+    - SAUCE: rtw88: fix rate for a while after being connected
+    - SAUCE: rtw88: Move driver IQK to set channel before association for 11N chip
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: rtw88: fix 'const' mismatch in power suequence hooks
+    - SAUCE: rtw88: fix 'const' mismatch in
+      __priority_queue_cfg_legacy()/__priority_queue_cfg()
+    - [Config] RTW88=m
+    - SAUCE: (lockdown) Revert carried-forward lockdown patches
+    - SAUCE: (lockdown) Add efi_status_to_str() and rework efi_status_to_err().
+    - SAUCE: (lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (lockdown) security: lockdown: expose a hook to lock the kernel down
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot
+      mode
+    - SAUCE: (lockdown) efi: Lock down the kernel if booted in secure boot mode
+    - SAUCE: (lockdown) s390: Lock down the kernel when the IPL secure flag is set
+    - SAUCE: (lockdown) KEYS: Make use of platform keyring for module signature
+      verify
+    - SAUCE: (lockdown) arm64: Allow locking down the kernel under EFI secure boot
+    - SAUCE: (lockdown) security: lockdown: Make
+      CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic
+    - [Config] Add back CONFIG_LOCK_DOWN_IN_SECURE_BOOT annotation for ppc64el
+    - [Config] CONFIG_RT_GROUP_SCHED=y
+    - [Packaging] Include modules.builtin.modinfo in linux-modules
+    - SAUCE: LSM: Infrastructure management of the sock security
+    - SAUCE: Fix-up af_unix mediation for sock infrastructure management
+    - SAUCE: Revert "apparmor: Allow filtering based on secmark policy"
+    - SAUCE: Revert "apparmor: Parse secmark policy"
+    - SAUCE: Revert "apparmor: Add a wildcard secid"
+    - SAUCE: Revert "apparmor: fixup secid map conversion to using IDR"
+    - SAUCE: Revert "apparmor: Use an IDR to allocate apparmor secids"
+    - SAUCE: Revert "apparmor: add support for mapping secids and using secctxes"
+    - Update dropped.txt for restored apparmor patches
+    - Remove lockdown patches from dropped.txt
+    - SAUCE: powerpc/ima: require IMA module signatures only if MODULE_SIG is not
+      enabled
+    - SAUCE: selftests/ftrace: Use printf instead of echo in kprobe syntax error
+      tests
+    - SAUCE: selftests/net -- disable l2tp.sh test
+    - SAUCE: selftests/net -- disable timeout
+    - SAUCE: tools: hv: Update shebang to use python3 instead of python
+    - Remove dropped.txt
+    - [Packaging] move linux-doc and linux-libc-dev stubs to debian.master
+    - [Debian] Support generating configs for riscv64
+    - [Config] CONFIG_KMSG_IDS=y for s390x
+    - [Packaging] add libcap-dev dependency
+    - [Config] CONFIG_AD5770R=m
+    - [Config] CONFIG_AL3010=m
+    - [Config] CONFIG_APPLE_MFI_FASTCHARGE=m
+    - [Config] CONFIG_BAREUDP=m
+    - [Config] CONFIG_CRYPTO_DEV_OCTEONTX_CPT=m
+    - [Config] CONFIG_CRYPTO_DEV_ZYNQMP_AES=m
+    - [Config] CONFIG_DRM_DISPLAY_CONNECTOR=m
+    - [Config] CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
+    - [Config] CONFIG_DRM_PANEL_ELIDA_KD35T133=m
+    - [Config] CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02=m
+    - [Config] CONFIG_DRM_PANEL_NOVATEK_NT35510=m
+    - [Config] CONFIG_DRM_PANEL_SAMSUNG_S6E88A0_AMS452EF01=m
+    - [Config] CONFIG_DRM_PARADE_PS8640=m
+    - [Config] CONFIG_DRM_SIMPLE_BRIDGE=m
+    - [Config] CONFIG_DRM_TIDSS=m
+    - [Config] CONFIG_DRM_TI_TPD12S015=m
+    - [Config] CONFIG_DRM_TOSHIBA_TC358768=m
+    - [Config] CONFIG_EDAC_DMC520=m
+    - [Config] CONFIG_EXFAT_FS=m
+    - [Config] CONFIG_GP2AP002=m
+    - [Config] CONFIG_GPIO_MLXBF2=m
+    - [Config] CONFIG_HID_GLORIOUS=m
+    - [Config] CONFIG_HID_MCP2221=m
+    - [Config] CONFIG_HMC425=m
+    - [Config] CONFIG_ICP10100=m
+    - [Config] CONFIG_IMX8MM_THERMAL=m
+    - [Config] CONFIG_IMX_SC_THERMAL=m
+    - [Config] CONFIG_INTERCONNECT_QCOM_OSM_L3=m
+    - [Config] CONFIG_INTERCONNECT_QCOM_SC7180=m
+    - [Config] CONFIG_K3_RTI_WATCHDOG=m
+    - [Config] CONFIG_MDIO_IPQ8064=m
+    - [Config] CONFIG_MDIO_MVUSB=m
+    - [Config] CONFIG_MHI_BUS=m
+    - [Config] CONFIG_OCTEONTX2_VF=m
+    - [Config] CONFIG_PHY_CADENCE_TORRENT=m
+    - [Config] CONFIG_PHY_QCOM_USB_HS_28NM=m
+    - [Config] CONFIG_PHY_QCOM_USB_SS=m
+    - [Config] CONFIG_PINCTRL_DA9062=m
+    - [Config] CONFIG_PINCTRL_IPQ6018=m
+    - [Config] CONFIG_PTP_1588_CLOCK_IDT82P33=m
+    - [Config] CONFIG_PTP_1588_CLOCK_VMW=m
+    - [Config] CONFIG_QCOM_IPA=m
+    - [Config] CONFIG_REGULATOR_MP5416=m
+    - [Config] CONFIG_REGULATOR_MP886X=m
+    - [Config] CONFIG_RN5T618_ADC=m
+    - [Config] CONFIG_RTC_DRV_MT2712=m
+    - [Config] CONFIG_RTC_DRV_RC5T619=m
+    - [Config] CONFIG_SC_MSS_7180=m
+    - [Config] CONFIG_SENSORS_AXI_FAN_CONTROL=m
+    - [Config] CONFIG_SM_GCC_8250=m
+    - [Config] CONFIG_SND_BCM63XX_I2S_WHISTLER=m
+    - [Config] CONFIG_SND_MESON_AIU=m
+    - [Config] CONFIG_SND_MESON_G12A_TOACODEC=m
+    - [Config] CONFIG_SND_MESON_GX_SOUND_CARD=m
+    - [Config] CONFIG_SND_SOC_AMD_RV_RT5682_MACH=m
+    - [Config] CONFIG_SND_SOC_INTEL_SOF_PCM512x_MACH=m
+    - [Config] CONFIG_SND_SOC_MESON_T9015=m
+    - [Config] CONFIG_SND_SOC_RT5682_SDW=m
+    - [Config] CONFIG_SND_SOC_TLV320ADCX140=m
+    - [Config] CONFIG_SPI_FSI=m
+    - [Config] CONFIG_SPI_MTK_NOR=m
+    - [Config] CONFIG_SPI_MUX=m
+    - [Config] CONFIG_SPRD_THERMAL=m
+    - [Config] CONFIG_SURFACE_3_POWER_OPREGION=m
+    - [Config] CONFIG_TINYDRM_ILI9486=m
+    - [Config] CONFIG_TI_K3_AM65_CPSW_NUSS=m
+    - [Config] CONFIG_TYPEC_MUX_INTEL_PMC=m
+    - [Config] CONFIG_UACCE=m
+    - [Config] CONFIG_UNIPHIER_XDMAC=m
+    - [Config] CONFIG_USB_MAX3420_UDC=m
+    - [Config] CONFIG_USB_RAW_GADGET=m
+    - [Config] CONFIG_VHOST_VDPA=m
+    - [Config] CONFIG_VIDEO_IMX219=m
+    - [Config] CONFIG_VIDEO_SUN8I_ROTATE=m
+    - [Config] CONFIG_VIRTIO_VDPA=m
+    - [Config] CONFIG_MOST_COMPONENTS=m
+    - [Config] CONFIG_MFD_IQS62X=m
+    - packaging: getabis: switch to ckt-ppa:bootstrap/linux-5.7
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: rtw88: add rtw_read8_mask and rtw_read16_mask"
+    - Revert "UBUNTU: SAUCE: drm/i915/fbc: disable framebuffer compression on
+      IceLake"
+    - Revert "UBUNTU: SAUCE: platform/x86: dell-uart-backlight: move retry block"
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 04 May 2020 10:48:48 +0200
+
+linux-5.7 (5.7.0-1.2) groovy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: hio: pass make_request ptr directly to blk_alloc_queue()
+    - SAUCE: hio: locally define disk_map_sector_rcu()
+    - SAUCE: hio: Revert "block: unexport disk_map_sector_rcu"
+    - SAUCE: hio: include <linux/part_stat.h>
+    - [Config] amd64: i386: HIO=m
+    - [Config] updateconfigs after 5.7-rc3 rebase
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 27 Apr 2020 11:31:38 +0200
+
+linux-5.7 (5.7.0-0.1) groovy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] updateconfigs after rebase to 5.7-rc1
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.7-rc1
+  * Rebase to v5.7-rc2
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 16 Apr 2020 11:53:58 +0200
+
+linux-5.7 (5.7.0-0.0) focal; urgency=medium
+
+  * Dummy entry
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Thu, 16 Apr 2020 11:53:58 +0200
+
+linux-5.6 (5.6.0-7.7) focal; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - update dkms package versions
+
+  * Kernel Oops - general protection fault: 0000 [#1] SMP PTI after
+    disconnecting thunderbolt docking station (LP: #1864754)
+    - SAUCE: ptp: free ptp clock properly
+
+  * swap storms kills interactive use (LP: #1861359)
+    - SAUCE: mm/page_alloc.c: disable memory reclaim watermark boosting by default
+
+  * sysfs: incorrect network device permissions on network namespace change
+    (LP: #1865359)
+    - sysfs: add sysfs_file_change_owner()
+    - sysfs: add sysfs_link_change_owner()
+    - sysfs: add sysfs_group{s}_change_owner()
+    - sysfs: add sysfs_change_owner()
+    - device: add device_change_owner()
+    - drivers/base/power: add dpm_sysfs_change_owner()
+    - net-sysfs: add netdev_change_owner()
+    - net-sysfs: add queue_change_owner()
+    - net: fix sysfs permssions when device changes network namespace
+    - sysfs: fix static inline declaration of sysfs_groups_change_owner()
+
+  * Miscellaneous Ubuntu changes
+    - [Config] updateconfigs after rebase to 5.6
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 31 Mar 2020 10:45:09 +0200
+
+linux-5.6 (5.6.0-6.6) focal; urgency=medium
+
+  * suspend only works once on ThinkPad X1 Carbon gen 7 (LP: #1865570)
+    - SAUCE: e1000e: Disable s0ix flow for X1 Carbon 7th
+
+  *  Make Dell WD19 dock more reliable after suspend (LP: #1868217)
+    - xhci: Ensure link state is U3 after setting USB_SS_PORT_LS_U3
+    - xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0
+    - xhci: Finetune host initiated USB3 rootport link suspend and resume
+
+  * update-version-dkms doesn't add a BugLink (LP: #1867790)
+    - [Packaging] Add BugLink to update-version-dkms commit
+
+  * Add support for Realtek 8723DE wireless adapter (LP: #1780590)
+    - SAUCE: rtw88: add regulatory process strategy for different chipset
+    - SAUCE: rtw88: support dynamic user regulatory setting
+    - SAUCE: rtw88: Use secondary channel offset enumeration
+    - SAUCE: rtw88: 8822c: modify rf protection setting
+    - SAUCE: rtw88: disable TX-AMSDU on 2.4G band
+    - SAUCE: Revert "rtw88: disable TX-AMSDU on 2.4G band"
+    - SAUCE: rtw88: disable TX-AMSDU on 2.4G band
+    - SAUCE: rtw88: remove unused parameter vif in rtw_lps_pg_info_get()
+    - SAUCE: rtw88: add rtw_read8_mask and rtw_read16_mask
+    - SAUCE: rtw88: pci: 8822c should set clock delay to zero
+    - SAUCE: rtw88: move rtw_enter_ips() to the last when config
+    - SAUCE: rtw88: avoid holding mutex for cancel_delayed_work_sync()
+    - SAUCE: rtw88: add ciphers to suppress error message
+    - SAUCE: rtw88: 8822c: update power sequence to v16
+    - SAUCE: rtw88: Fix incorrect beamformee role setting
+    - SAUCE: rtw88: don't hold all IRQs disabled for PS operations
+    - SAUCE: rtw88: extract alloc rsvd_page and h2c skb routines
+    - SAUCE: rtw88: associate reserved pages with each vif
+    - SAUCE: rtw88: add adaptivity support for EU/JP regulatory
+    - SAUCE: rtw88: 8723d: Add basic chip capabilities
+    - SAUCE: rtw88: 8723d: add beamform wrapper functions
+    - SAUCE: rtw88: 8723d: Add power sequence
+    - SAUCE: rtw88: 8723d: Add RF read/write ops
+    - SAUCE: rtw88: 8723d: Add mac/bb/rf/agc/power_limit tables
+    - SAUCE: rtw88: 8723d: Add cfg_ldo25 to control LDO25
+    - SAUCE: rtw88: 8723d: Add new chip op efuse_grant() to control efuse access
+    - SAUCE: rtw88: 8723d: Add read_efuse to recognize efuse info from map
+    - SAUCE: rtw88: add legacy firmware download for 8723D devices
+    - SAUCE: rtw88: no need to send additional information to legacy firmware
+    - SAUCE: rtw88: 8723d: Add mac power-on/-off function
+    - SAUCE: rtw88: decompose while(1) loop of power sequence polling command
+    - SAUCE: rtw88: 8723d: 11N chips don't support H2C queue
+    - SAUCE: rtw88: 8723d: implement set_tx_power_index ops
+    - SAUCE: rtw88: 8723d: Organize chip TX/RX FIFO
+    - SAUCE: rtw88: 8723d: initialize mac/bb/rf basic functions
+    - SAUCE: rtw88: 8723d: Add DIG parameter
+    - SAUCE: rtw88: 8723d: Add query_rx_desc
+    - SAUCE: rtw88: 8723d: Add set_channel
+    - SAUCE: rtw88: handle C2H_CCX_TX_RPT to know if packet TX'ed successfully
+    - SAUCE: rtw88: 8723d: 11N chips don't support LDPC
+    - SAUCE: rtw88: set default port to firmware
+    - SAUCE: rtw88: update tx descriptor of mgmt and rsvd page packets
+    - SAUCE: rtw88: sar: add SAR of TX power limit
+    - SAUCE: rtw88: sar: Load static SAR table from ACPI WRDS method
+    - SAUCE: rtw88: sar: Load dynamic SAR table from ACPI methods
+    - SAUCE: rtw88: sar: apply dynamic SAR table to tx power limit
+    - SAUCE: rtw88: sar: add sar_work to poll if dynamic SAR table is changed
+    - SAUCE: rtw88: sar: dump sar information via debugfs
+    - SAUCE: rtw88: 8723d: Add chip_ops::false_alarm_statistics
+    - SAUCE: rtw88: 8723d: Set IG register for CCK rate
+    - SAUCE: rtw88: 8723d: add interface configurations table
+    - SAUCE: rtw88: 8723d: Add LC calibration
+    - SAUCE: rtw88: 8723d: add IQ calibration
+    - SAUCE: rtw88: 8723d: Add power tracking
+    - SAUCE: rtw88: 8723d: Add shutdown callback to disable BT USB suspend
+    - SAUCE: rtw88: 8723d: implement flush queue
+    - SAUCE: rtw88: 8723d: set ltecoex register address in chip_info
+    - SAUCE: rtw88: 8723d: Add coex support
+    - SAUCE: rtw88: fill zeros to words 0x06 and 0x07 of security cam entry
+    - SAUCE: rtw88: 8723d: Add 8723DE to Kconfig and Makefile
+    - [Config] CONFIG_RTW88_8723DE=y
+
+  * [Ubuntu 20.04] Unset HIBERNATION and PM kernel config options for focal
+    (LP: #1867753)
+    - [Config] CONFIG_HIBERNATION=n and CONFIG_PM=n for s390x
+
+  * [20.04 FEAT] Base KVM setup for secure guests - kernel part (LP: #1835531)
+    - s390/protvirt: introduce host side setup
+    - s390/protvirt: add ultravisor initialization
+    - s390/mm: provide memory management functions for protected KVM guests
+    - s390/mm: add (non)secure page access exceptions handlers
+    - s390/protvirt: Add sysfs firmware interface for Ultravisor information
+    - KVM: s390/interrupt: do not pin adapter interrupt pages
+    - KVM: s390: protvirt: Add UV debug trace
+    - KVM: s390: add new variants of UV CALL
+    - KVM: s390: protvirt: Add initial vm and cpu lifecycle handling
+    - KVM: s390: protvirt: Secure memory is not mergeable
+    - KVM: s390/mm: Make pages accessible before destroying the guest
+    - KVM: s390: protvirt: Handle SE notification interceptions
+    - KVM: s390: protvirt: Instruction emulation
+    - KVM: s390: protvirt: Implement interrupt injection
+    - KVM: s390: protvirt: Add SCLP interrupt handling
+    - KVM: s390: protvirt: Handle spec exception loops
+    - KVM: s390: protvirt: Add new gprs location handling
+    - KVM: S390: protvirt: Introduce instruction data area bounce buffer
+    - KVM: s390: protvirt: handle secure guest prefix pages
+    - KVM: s390/mm: handle guest unpin events
+    - KVM: s390: protvirt: Write sthyi data to instruction data area
+    - KVM: s390: protvirt: STSI handling
+    - KVM: s390: protvirt: disallow one_reg
+    - KVM: s390: protvirt: Do only reset registers that are accessible
+    - KVM: s390: protvirt: Only sync fmt4 registers
+    - KVM: s390: protvirt: Add program exception injection
+    - KVM: s390: protvirt: UV calls in support of diag308 0, 1
+    - KVM: s390: protvirt: Report CPU state to Ultravisor
+    - KVM: s390: protvirt: Support cmd 5 operation state
+    - KVM: s390: protvirt: Mask PSW interrupt bits for interception 104 and 112
+    - KVM: s390: protvirt: do not inject interrupts after start
+    - KVM: s390: protvirt: Add UV cpu reset calls
+    - DOCUMENTATION: Protected virtual machine introduction and IPL
+    - KVM: s390: protvirt: introduce and enable KVM_CAP_S390_PROTECTED
+    - KVM: s390: protvirt: Add KVM api documentation
+    - mm/gup/writeback: add callbacks for inaccessible pages
+
+  * All PS/2 ports on PS/2 Serial add-in bracket are not working after S3
+    (LP: #1866734)
+    - SAUCE: Input: i8042 - fix the selftest retry logic
+
+  * Sys oopsed with sysfs test in ubuntu_stress_smoke_test on X-hwe ARM64
+    (LP: #1866772)
+    - ACPI: sysfs: copy ACPI data using io memory copying
+
+  * Miscellaneous Ubuntu changes
+    - hio -- remove duplicated MODULE_DEVICE_TABLE declaration
+    - SAUCE: r8169: disable ASPM L1.1
+    - [Config] update annotations from configs
+    - [Config] update configs after annotation file review
+    - SAUCE: Revert "tools/power turbostat: Fix 32-bit capabilities warning"
+
+  * Miscellaneous upstream changes
+    - drm/i915: Fix eDP DPCD aux max backlight calculations
+    - drm/dp: Introduce EDID-based quirks
+    - drm/i915: Force DPCD backlight mode on X1 Extreme 2nd Gen 4K AMOLED panel
+    - drm/i915: Force DPCD backlight mode for some Dell CML 2020 panels
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.6-rc7
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 25 Mar 2020 18:09:13 +0100
+
+linux-5.6 (5.6.0-5.5) focal; urgency=medium
+
+  * please help enable CONFIG_EROFS_FS_ZIP (LP: #1867099)
+    - [Config] CONFIG_EROFS_FS_ZIP=y
+    - [Config] CONFIG_EROFS_FS_CLUSTER_PAGE_LIMIT=1
+
+  * Miscellaneous Ubuntu changes
+    - Config: Fix SND_HDA_PREALLOC_SIZE annotations
+    - Config: Fix DATA_SHIFT annotations
+    - Config: remove ANDROID_VSOC from annotations
+    - Config: remove arm arch from annotations
+    - Config: Update SOC_R8A7796X annotations
+    - Config: Update CLK_R8A7796X annotations
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.6-rc6
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.6-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 18 Mar 2020 17:25:30 +0100
+
+linux-5.6 (5.6.0-4.4) focal; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync getabis
+    - [Packaging] update helper scripts
+
+  * Add sysfs attribute to show remapped NVMe (LP: #1863621)
+    - SAUCE: ata: ahci: Add sysfs attribute to show remapped NVMe device count
+
+  * [20.04 FEAT] Compression improvements in Linux kernel (LP: #1830208)
+    - [Config] Introducing s390x specific kernel config option CONFIG_ZLIB_DFLTCC
+
+  * [UBUNTU 20.04] s390x/pci: increase CONFIG_PCI_NR_FUNCTIONS to 512 in kernel
+    config (LP: #1866056)
+    - [Config] Increase CONFIG_PCI_NR_FUNCTIONS from 64 to 512 starting with focal
+      on s390x
+
+  * CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set (LP: #1865332)
+    - [Config] CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
+
+  * [UBUNTU 20.04] Enable CONFIG_NET_SWITCHDEV in kernel config for s390x
+    starting with focal (LP: #1865452)
+    - [Config] Enable CONFIG_NET_SWITCHDEV in kernel config for s390x starting
+      with focal
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "UBUNTU: SAUCE: blk/core: Gracefully handle unset
+      make_request_fn"
+    - [Packaging] prevent duplicated entries in modules.ignore
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.6-rc5
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.6-rc5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 09 Mar 2020 09:42:06 +0100
+
+linux-5.6 (5.6.0-3.3) focal; urgency=medium
+
+  * nsleep-lat / set-timer-lat / inconsistency-check / raw_skew from timer in
+    ubuntu_kernel_selftests timeout on 5.3 / 5.4 (LP: #1864626)
+    - selftests/timers: Turn off timeout setting
+
+  * Update kernel options CONFIG_NR_CPUS and CONFIG_NUMA_EMU for focal
+    (LP: #1864198)
+    - Ubuntu: [Config] Update kernel options CONFIG_NR_CPUS and CONFIG_NUMA_EMU
+
+  * alsa/hda/realtek: fix a mute led regression on Lenovo X1 Carbon
+    (LP: #1864576)
+    - SAUCE: ALSA: hda/realtek - Fix a regression for mute led on Lenovo Carbon X1
+
+  * r8152 init may take up to 40 seconds at initialization with Dell WD19/WD19DC
+    during hotplug (LP: #1864284)
+    - UBUNTU SAUCE: r8151: check disconnect status after long sleep
+
+  * Another Dell AIO backlight issue (LP: #1863880)
+    - SAUCE: platform/x86: dell-uart-backlight: move retry block
+
+  * Backport GetFB2 ioctl (LP: #1863874)
+    - SAUCE: drm: Add getfb2 ioctl
+
+  * Focal Fossa (20.04) feature request - Enable CONFIG_X86_UV (LP: #1863810)
+    - [Config] CONFIG_X86_UV=y
+
+  * Miscellaneous Ubuntu changes
+    - debian: remove snapdragon config, rules and flavour
+    - remove snapdragon abi files
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.6-rc4
+
+  * Miscellaneous upstream changes
+    - updateconfigs following snapdragon removal
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.6-rc4
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 04 Mar 2020 08:21:10 +0100
+
+linux-5.6 (5.6.0-2.2) focal; urgency=medium
+
+  * Sometimes can't adjust brightness on Dell AIO (LP: #1862885)
+    - SAUCE: platform/x86: dell-uart-backlight: increase retry times
+
+  * Dell XPS 13 (7390) Display Flickering - 19.10  (LP: #1849947)
+    - SAUCE: drm/i915: Disable PSR by default on all platforms
+
+  * Miscellaneous Ubuntu changes
+    - [debian] ignore missing wireguard module
+    - SAUCE: (lockdown) Add efi_status_to_str() and rework efi_status_to_err().
+    - SAUCE: (lockdown) security: lockdown: expose a hook to lock the kernel down
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot
+      mode
+    - SAUCE: (lockdown) efi: Lock down the kernel if booted in secure boot mode
+    - SAUCE: (lockdown) s390: Lock down the kernel when the IPL secure flag is set
+    - SAUCE: (lockdown) KEYS: Make use of platform keyring for module signature
+      verify
+    - SAUCE: (lockdown) arm64: Allow locking down the kernel under EFI secure boot
+    - SAUCE: (lockdown) security: lockdown: Make
+      CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic
+    - [Config] CONFIG_LOCK_DOWN_IN_SECURE_BOOT=y
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.6-rc3
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: (lockdown) s390/ipl: lockdown kernel when booted
+      secure"
+    - Revert "UBUNTU: SAUCE: (lockdown) KEYS: Make use of platform keyring for
+      module signature verify"
+    - Revert "UBUNTU: SAUCE: (lockdown) Add a SysRq option to lift kernel
+      lockdown"
+    - Revert "UBUNTU: SAUCE: (lockdown) security: lockdown: expose a hook to lock
+      the kernel down"
+    - Revert "UBUNTU: SAUCE: (lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err()."
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 24 Feb 2020 18:57:22 +0100
+
+linux-5.6 (5.6.0-1.1) focal; urgency=medium
+
+  *  Integrate Intel SGX driver into linux-azure (LP: #1844245)
+    - [Packaging] Add systemd service to load intel_sgx
+
+  * QAT drivers for C3XXX and C62X not included as modules (LP: #1845959)
+    - [Config] CRYPTO_DEV_QAT_C3XXX=m, CRYPTO_DEV_QAT_C62X=m and
+      CRYPTO_DEV_QAT_DH895xCC=m
+
+  * 5.4.0-11 crash on cryptsetup open (LP: #1860231)
+    - SAUCE: blk/core: Gracefully handle unset make_request_fn
+
+  * multi-zone raid0 corruption (LP: #1850540)
+    - SAUCE: md/raid0: Use kernel specific layout
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - update dropped.txt after rebase to v5.6-rc1
+    - [Config] updateconfigs after rebase to 5.6-rc1
+    - hio -- proc_create() requires a "struct proc_ops" in 5.6
+    - SAUCE: arm: fix build error in kvm tracepoint
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: [Config] Disable the uselib system call"
+    - Revert "UBUNTU: [Config] Disable legacy PTY naming"
+    - Revert "UBUNTU: [Config] Enforce filtered access to iomem"
+    - Revert "UBUNTU: [Config] Enable notifier call chain validations"
+    - Revert "UBUNTU: [Config] Enable scatterlist validation"
+    - Revert "UBUNTU: [Config] Enable cred sanity checks"
+    - Revert "UBUNTU: [Config] Enable linked list manipulation checks"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.6-rc1
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 13 Feb 2020 17:20:27 +0100
+
+linux-5.6 (5.6.0-0.0) focal; urgency=medium
+
+  * Dummy entry
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 10 Feb 2020 11:06:18 +0100
+
+linux-5.5 (5.5.0-7.8) focal; urgency=medium
+
+  * CONFIG_USELIB should be disabled (LP: #1855341)
+    - [Config] Disable the uselib system call
+
+  * CONFIG_LEGACY_PTYS should be disabled (LP: #1855339)
+    - [Config] Disable legacy PTY naming
+
+  * CONFIG_IO_STRICT_DEVMEM should be enabled (LP: #1855338)
+    - [Config] Enforce filtered access to iomem
+
+  * CONFIG_DEBUG_NOTIFIERS should be enabled (LP: #1855337)
+    - [Config] Enable notifier call chain validations
+
+  * CONFIG_DEBUG_SG should be enabled (LP: #1855336)
+    - [Config] Enable scatterlist validation
+
+  * CONFIG_DEBUG_CREDENTIALS should be enabled (LP: #1855335)
+    - [Config] Enable cred sanity checks
+
+  * CONFIG_DEBUG_LIST should be enabled (LP: #1855334)
+    - [Config] Enable linked list manipulation checks
+
+  * shiftfs: prevent lower dentries from going negative during unlink
+    (LP: #1860041)
+    - SAUCE: shiftfs: prevent lower dentries from going negative during unlink
+
+  * [SRU][B/OEM-B/OEM-OSP1/D/E/Unstable] UBUNTU: SAUCE: Use native backlight on
+    Lenovo E41-25/45 (LP: #1859561)
+    - SAUCE: ACPI: video: Use native backlight on Lenovo E41-25/45
+
+  * USB key cannot be detected by hotplug on Sunix USB Type-A 3.1 Gen 2 card
+    [1b21:2142]  (LP: #1858988)
+    - SAUCE: PCI: Avoid ASMedia XHCI USB PME# from D0 defect
+
+  * Dell AIO can't adjust brightness (LP: #1858761)
+    - SAUCE: platform/x86: dell-uart-backlight: add retry for get scalar status
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Fix typo in annotations file
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 27 Jan 2020 11:39:38 +0100
+
+linux-5.5 (5.5.0-6.7) focal; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Update ubuntu-regression-suite dependency to python2
+    - [Packaging] Fix ubuntu-regression-suite python dependency for hwe kernel
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.5-rc7
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 20 Jan 2020 10:16:01 +0100
+
+linux-5.5 (5.5.0-5.6) focal; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.5-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 13 Jan 2020 15:50:12 +0100
+
+linux-5.5 (5.5.0-4.5) focal; urgency=medium
+
+  * linux build and autopkg tests need to use python2 instead of python
+    (LP: #1858487)
+    - [Packaging] Remove python-dev build dependency
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 08 Jan 2020 16:00:26 +0100
+
+linux-5.5 (5.5.0-3.4) focal; urgency=medium
+
+  * [SRU][B/OEM-B/OEM-OSP1/D/E/F] Add LG I2C touchscreen multitouch support
+    (LP: #1857541)
+    - SAUCE: HID: multitouch: Add LG MELF0410 I2C touchscreen support
+
+  * Make vfio-pci built-in or xhci_hcd optional (LP: #1770845)
+    - [Config]: built-in VFIO_PCI for amd64
+
+  * multi-zone raid0 corruption (LP: #1850540)
+    - SAUCE: md/raid0: Link to wiki with guidance on multi-zone RAID0 layout
+      migration
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Change source package to linux-5.5
+    - [Packaging] Don't use SRCPKGNAME for linux-libc-dev
+    - [Packaging] Remove linux-source-3 Provides: from linux-source
+    - [Packaging] Fix linux-doc in linux-image Suggests:
+    - [Debian] Read variants list into a variable
+    - [Packaging] Generate linux-libc-dev package only for primary variant
+    - [Packaging] Generate linux-doc for only the primary variant
+    - [Debian] Update linux source package name in debian/tests/*
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.5-rc3
+    - [Config] disable PCI_MESON
+    - [Config] Add pinctrl-equilibrium to modules.ignore
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.5-rc5
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Wed, 08 Jan 2020 11:28:43 +0100
+
+linux-5.5 (5.5.0-2.3) focal; urgency=medium
+
+  * Empty entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 17 Dec 2019 22:33:59 -0600
+
+linux (5.5.0-2.3) focal; urgency=medium
+
+  * Support DPCD aux brightness control (LP: #1856134)
+    - SAUCE: drm/i915: Fix eDP DPCD aux max backlight calculations
+    - SAUCE: drm/i915: Assume 100% brightness when not in DPCD control mode
+    - SAUCE: drm/i915: Fix DPCD register order in intel_dp_aux_enable_backlight()
+    - SAUCE: drm/i915: Auto detect DPCD backlight support by default
+    - SAUCE: drm/i915: Force DPCD backlight mode on X1 Extreme 2nd Gen 4K AMOLED
+      panel
+    - USUNTU: SAUCE: drm/i915: Force DPCD backlight mode on Dell Precision 4K sku
+
+  * change kconfig of the soundwire bus driver from y to m (LP: #1855685)
+    - [Config]: SOUNDWIRE=m
+
+  * Fix unusable USB hub on Dell TB16 after S3 (LP: #1855312)
+    - SAUCE: USB: core: Make port power cycle a seperate helper function
+    - SAUCE: USB: core: Attempt power cycle port when it's in eSS.Disabled state
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] add python depends to ubuntu-regression-suite
+    - SAUCE: selftests: net: tls: remove recv_rcvbuf test
+    - update dkms package versions
+
+  * Miscellaneous upstream changes
+    - [Config] updateconfigs after rebase to 5.5-rc2
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Tue, 17 Dec 2019 16:02:43 +0100
+
+linux (5.5.0-1.2) focal; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] disable nvidia dkms build
+    - [Config] disable virtualbox dkms build
+    - [Config] disable zfs dkms build
+    - update dropped.txt after rebase to v5.5-rc1
+    - SAUCE: (lockdown) Make get_cert_list() not complain about cert lists that
+      aren't present.
+    - SAUCE: (lockdown) Add efi_status_to_str() and rework efi_status_to_err().
+    - SAUCE: (lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (lockdown) security: lockdown: expose a hook to lock the kernel down
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot
+      mode
+    - SAUCE: (lockdown) efi: Lock down the kernel if booted in secure boot mode
+    - SAUCE: (lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (lockdown) KEYS: Make use of platform keyring for module signature
+      verify
+    - SAUCE: (lockdown) arm64: Allow locking down the kernel under EFI secure boot
+    - SAUCE: (lockdown) security: lockdown: Make
+      CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic
+    - SAUCE: (lockdown) s390/ipl: lockdown kernel when booted secure
+    - [Config] Enable lockdown under secure boot
+    - update dkms package versions
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Thu, 12 Dec 2019 16:54:41 +0100
+
+linux (5.5.0-0.1) focal; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] updateconfigs after rebase to 5.5-rc1
+
+   [ Upstream Kernel Changes ]
+
+   * Rebase to v5.5-rc1
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 09 Dec 2019 19:03:35 +0100
+
+linux (5.5.0-0.0) focal; urgency=medium
+
+  * Dummy entry.
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 09 Dec 2019 15:14:37 +0100
+
+linux (5.4.0-8.11) focal; urgency=medium
+
+  * focal/linux: 5.4.0-8.9 -proposed tracker (LP: #1855448)
+
+  * update ENA driver for DIMLIB dynamic interrupt moderation (LP: #1853180)
+    - SAUCE: net: ena: fix issues in setting interrupt moderation params in
+      ethtool
+    - SAUCE: net: ena: fix too long default tx interrupt moderation interval
+
+  * Kernel build log filled with "/bin/bash: line 5: warning: command
+    substitution: ignored null byte in input" (LP: #1853843)
+    - [Debian] Fix warnings when checking for modules signatures
+
+  * hwe-edge kernel 5.3.0-23.25 kernel does not boot on Precision 5720 AIO
+    (LP: #1852581)
+    - [Packaging] Fix module signing with older modinfo
+
+  * Fix MST support on Ice Lake (LP: #1854432)
+    - drm/i915: fix port checks for MST support on gen >= 11
+
+  * headphone has noise as not mute on dell machines with alc236/256
+    (LP: #1854401)
+    - SAUCE: ALSA: hda/realtek - Dell headphone has noise on unmute for ALC236
+
+  * [CML-S62] Need enable intel_pmc_core driver patch for Comet lake- S 6+2
+    (LP: #1847450)
+    - SAUCE: platform/x86: intel_pmc_core: Add Comet Lake (CML) platform support
+      to intel_pmc_core driver
+
+  * CVE-2019-14901
+    - SAUCE: mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()
+
+  * CVE-2019-14896 // CVE-2019-14897
+    - SAUCE: libertas: Fix two buffer overflows at parsing bss descriptor
+
+  * CVE-2019-14895
+    - SAUCE: mwifiex: fix possible heap overflow in mwifiex_process_country_ie()
+
+  * [CML-S62] Need enable intel_rapl patch support for Comet lake- S 6+2
+    (LP: #1847454)
+    - powercap/intel_rapl: add support for CometLake Mobile
+    - powercap/intel_rapl: add support for Cometlake desktop
+
+  * External microphone can't work on some dell machines with the codec alc256
+    or alc236 (LP: #1853791)
+    - SAUCE: ALSA: hda/realtek - Move some alc256 pintbls to fallback table
+    - SAUCE: ALSA: hda/realtek - Move some alc236 pintbls to fallback table
+
+  * remount of multilower moved pivoted-root overlayfs root, results in I/O
+    errors on some modified files (LP: #1824407)
+    - SAUCE: ovl: fix lookup failure on multi lower squashfs
+
+  * [CML-S62] Need enable turbostat patch support for Comet lake- S 6+2
+    (LP: #1847451)
+    - SAUCE: tools/power turbostat: Add Cometlake support
+
+  * CONFIG_ARCH_ROCKCHIP is not set in ubuntu 18.04 aarch64,arm64 (LP: #1825222)
+    - [Config] Enable ROCKCHIP support for arm64
+
+  * [broadwell-rt286, playback] Since Linux 5.2rc2 audio playback no longer
+    works on Dell Venue 11 Pro 7140 (LP: #1846539)
+    - SAUCE: ASoC: SOF: Intel: Broadwell: clarify mutual exclusion with legacy
+      driver
+
+  * i40e: general protection fault in i40e_config_vf_promiscuous_mode
+    (LP: #1852663)
+    - SAUCE: i40e Fix GPF when deleting VMs
+
+  * libbpf check_abi fails on ppc64el (LP: #1854974)
+    - libbpf: Fix readelf output parsing on powerpc with recent binutils
+
+  * CVE-2019-19050
+    - crypto: user - fix memory leak in crypto_reportstat
+
+  * Make hotplugging docking station to Thunderbolt port more reliable
+    (LP: #1853991)
+    - PCI/PM: Add pcie_wait_for_link_delay()
+    - PCI/PM: Add missing link delays required by the PCIe spec
+
+  * i915: Display flickers (monitor loses signal briefly) during "flickerfree"
+    boot, while showing the BIOS logo on a black background (LP: #1836858)
+    - [Config] FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER=y
+
+  * [CML] New device id's for CMP-H (LP: #1846335)
+    - i2c: i801: Add support for Intel Comet Lake PCH-H
+    - mtd: spi-nor: intel-spi: Add support for Intel Comet Lake-H SPI serial flash
+    - mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
+
+  * Focal update: v5.4.2 upstream stable release (LP: #1855326)
+    - io_uring: async workers should inherit the user creds
+    - net: separate out the msghdr copy from ___sys_{send,recv}msg()
+    - net: disallow ancillary data for __sys_{send,recv}msg_file()
+    - crypto: inside-secure - Fix stability issue with Macchiatobin
+    - driver core: platform: use the correct callback type for bus_find_device
+    - usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
+    - staging: wilc1000: fix illegal memory access in wilc_parse_join_bss_param()
+    - staging: rtl8192e: fix potential use after free
+    - staging: rtl8723bs: Drop ACPI device ids
+    - staging: rtl8723bs: Add 024c:0525 to the list of SDIO device-ids
+    - USB: serial: ftdi_sio: add device IDs for U-Blox C099-F9P
+    - mei: bus: prefix device names on bus with the bus name
+    - mei: me: add comet point V device id
+    - thunderbolt: Power cycle the router if NVM authentication fails
+    - x86/fpu: Don't cache access to fpu_fpregs_owner_ctx
+    - gve: Fix the queue page list allocated pages count
+    - macvlan: schedule bc_work even if error
+    - mdio_bus: don't use managed reset-controller
+    - net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
+    - net: macb: add missed tasklet_kill
+    - net: psample: fix skb_over_panic
+    - net: sched: fix `tc -s class show` no bstats on class with nolock subqueues
+    - openvswitch: fix flow command message size
+    - sctp: Fix memory leak in sctp_sf_do_5_2_4_dupcook
+    - slip: Fix use-after-free Read in slip_open
+    - sctp: cache netns in sctp_ep_common
+    - openvswitch: drop unneeded BUG_ON() in ovs_flow_cmd_build_info()
+    - openvswitch: remove another BUG_ON()
+    - net/tls: take into account that bpf_exec_tx_verdict() may free the record
+    - net/tls: free the record on encryption error
+    - net: skmsg: fix TLS 1.3 crash with full sk_msg
+    - selftests/tls: add a test for fragmented messages
+    - net/tls: remove the dead inplace_crypto code
+    - net/tls: use sg_next() to walk sg entries
+    - selftests: bpf: test_sockmap: handle file creation failures gracefully
+    - selftests: bpf: correct perror strings
+    - tipc: fix link name length check
+    - selftests: pmtu: use -oneline for ip route list cache
+    - r8169: fix jumbo configuration for RTL8168evl
+    - r8169: fix resume on cable plug-in
+    - ext4: add more paranoia checking in ext4_expand_extra_isize handling
+    - Revert "jffs2: Fix possible null-pointer dereferences in
+      jffs2_add_frag_to_fragtree()"
+    - crypto: talitos - Fix build error by selecting LIB_DES
+    - HID: core: check whether Usage Page item is after Usage ID items
+    - platform/x86: hp-wmi: Fix ACPI errors caused by too small buffer
+    - platform/x86: hp-wmi: Fix ACPI errors caused by passing 0 as input size
+    - Linux 5.4.2
+
+  * no HDMI video output since GDM greeter after linux-oem-osp1 version
+    5.0.0-1026 (LP: #1852386)
+    - drm/i915: Add new CNL PCH ID seen on a CML platform
+    - SAUCE: drm/i915: Fix detection for a CMP-V PCH
+
+  * Please add patch fixing RK818 ID detection (LP: #1853192)
+    - SAUCE: mfd: rk808: Fix RK818 ID template
+
+  * Raydium Touchscreen on ThinkPad L390 does not work (LP: #1849721)
+    - HID: i2c-hid: fix no irq after reset on raydium 3118
+
+  * Touchpad doesn't work on Dell Inspiron 7000 2-in-1 (LP: #1851901)
+    - Revert "UBUNTU: SAUCE: mfd: intel-lpss: add quirk for Dell XPS 13 7390
+      2-in-1"
+    - lib: devres: add a helper function for ioremap_uc
+    - mfd: intel-lpss: Use devm_ioremap_uc for MMIO
+
+  * Lenovo dock MAC Address pass through doesn't work in Ubuntu  (LP: #1827961)
+    - r8152: Add macpassthru support for ThinkPad Thunderbolt 3 Dock Gen 2
+
+  * Disable unreliable HPET on CFL-H system (LP: #1852216)
+    - SAUCE: x86/intel: Disable HPET on Intel Coffe Lake H platforms
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - [Config] Enable virtualbox dkms build
+    - [Config] update annotations to match current configs
+    - SAUCE: Add exfat module to signature inclusion list
+
+  * Miscellaneous upstream changes
+    - Bluetooth: Fix invalid-free in bcsp_close()
+    - ath9k_hw: fix uninitialized variable data
+    - ath10k: Fix a NULL-ptr-deref bug in ath10k_usb_alloc_urb_from_pipe
+    - ath10k: Fix HOST capability QMI incompatibility
+    - ath10k: restore QCA9880-AR1A (v1) detection
+    - Revert "Bluetooth: hci_ll: set operational frequency earlier"
+    - Revert "dm crypt: use WQ_HIGHPRI for the IO and crypt workqueues"
+    - md/raid10: prevent access of uninitialized resync_pages offset
+    - x86/insn: Fix awk regexp warnings
+    - x86/speculation: Fix incorrect MDS/TAA mitigation status
+    - x86/speculation: Fix redundant MDS mitigation message
+    - nbd: prevent memory leak
+    - x86/stackframe/32: Repair 32-bit Xen PV
+    - x86/xen/32: Make xen_iret_crit_fixup() independent of frame layout
+    - x86/xen/32: Simplify ring check in xen_iret_crit_fixup()
+    - x86/doublefault/32: Fix stack canaries in the double fault handler
+    - x86/pti/32: Size initial_page_table correctly
+    - x86/cpu_entry_area: Add guard page for entry stack on 32bit
+    - x86/entry/32: Fix IRET exception
+    - x86/entry/32: Use %ss segment where required
+    - x86/entry/32: Move FIXUP_FRAME after pushing %fs in SAVE_ALL
+    - x86/entry/32: Unwind the ESPFIX stack earlier on exception entry
+    - x86/entry/32: Fix NMI vs ESPFIX
+    - selftests/x86/mov_ss_trap: Fix the SYSENTER test
+    - selftests/x86/sigreturn/32: Invalidate DS and ES when abusing the kernel
+    - x86/pti/32: Calculate the various PTI cpu_entry_area sizes correctly, make
+      the CPU_ENTRY_AREA_PAGES assert precise
+    - x86/entry/32: Fix FIXUP_ESPFIX_STACK with user CR3
+    - futex: Prevent robust futex exit race
+    - ALSA: usb-audio: Fix NULL dereference at parsing BADD
+    - ALSA: usb-audio: Fix Scarlett 6i6 Gen 2 port data
+    - media: vivid: Set vid_cap_streaming and vid_out_streaming to true
+    - media: vivid: Fix wrong locking that causes race conditions on streaming
+      stop
+    - media: usbvision: Fix invalid accesses after device disconnect
+    - media: usbvision: Fix races among open, close, and disconnect
+    - cpufreq: Add NULL checks to show() and store() methods of cpufreq
+    - futex: Move futex exit handling into futex code
+    - futex: Replace PF_EXITPIDONE with a state
+    - exit/exec: Seperate mm_release()
+    - futex: Split futex_mm_release() for exit/exec
+    - futex: Set task::futex_state to DEAD right after handling futex exit
+    - futex: Mark the begin of futex exit explicitly
+    - futex: Sanitize exit state handling
+    - futex: Provide state handling for exec() as well
+    - futex: Add mutex around futex exit
+    - futex: Provide distinct return value when owner is exiting
+    - futex: Prevent exit livelock
+    - media: uvcvideo: Fix error path in control parsing failure
+    - media: b2c2-flexcop-usb: add sanity checking
+    - media: cxusb: detect cxusb_ctrl_msg error in query
+    - media: imon: invalid dereference in imon_touch_event
+    - media: mceusb: fix out of bounds read in MCE receiver buffer
+    - ALSA: hda - Disable audio component for legacy Nvidia HDMI codecs
+    - USBIP: add config dependency for SGL_ALLOC
+    - usbip: tools: fix fd leakage in the function of read_attr_usbip_status
+    - usbip: Fix uninitialized symbol 'nents' in stub_recv_cmd_submit()
+    - usb-serial: cp201x: support Mark-10 digital force gauge
+    - USB: chaoskey: fix error case of a timeout
+    - appledisplay: fix error handling in the scheduled work
+    - USB: serial: mos7840: add USB ID to support Moxa UPort 2210
+    - USB: serial: mos7720: fix remote wakeup
+    - USB: serial: mos7840: fix remote wakeup
+    - USB: serial: option: add support for DW5821e with eSIM support
+    - USB: serial: option: add support for Foxconn T77W968 LTE modules
+    - staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
+    - powerpc/book3s64: Fix link stack flush on context switch
+    - KVM: PPC: Book3S HV: Flush link stack on guest exit to host kernel
+    - Linux 5.4.1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 06 Dec 2019 15:53:53 -0600
+
+linux (5.4.0-7.8) focal; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests/bpf: Comment out BPF_CORE_READ's which cause clang to
+      segfault
+    - Update nvidia-430 to nvidia-440
+    - [Config] Enable nvidia dkms build
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 25 Nov 2019 15:02:30 +0100
+
+linux (5.4.0-6.7) focal; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.4-rc8
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc7
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 18 Nov 2019 12:08:01 +0100
+
+linux (5.4.0-5.6) focal; urgency=medium
+
+  * refcount underflow and type confusion in shiftfs (LP: #1850867) //
+    CVE-2019-15793
+    - SAUCE: shiftfs: Correct id translation for lower fs operations
+
+  * refcount underflow and type confusion in shiftfs (LP: #1850867) //
+    CVE-2019-15792
+    - SAUCE: shiftfs: prevent type confusion
+
+  * refcount underflow and type confusion in shiftfs (LP: #1850867) //
+    CVE-2019-15791
+    - SAUCE: shiftfs: Fix refcount underflow in btrfs ioctl handling
+
+  * Some EFI systems fail to boot in efi_init() when booted via maas
+    (LP: #1851810)
+    - SAUCE: efi: efi_get_memory_map -- increase map headroom
+
+  * seccomp: fix SECCOMP_USER_NOTIF_FLAG_CONTINUE test (LP: #1849281)
+    - SAUCE: seccomp: rework define for SECCOMP_USER_NOTIF_FLAG_CONTINUE
+    - SAUCE: seccomp: avoid overflow in implicit constant conversion
+
+  * dkms artifacts may expire from the pool (LP: #1850958)
+    - [Packaging] dkms -- try launchpad librarian for pool downloads
+    - [Packaging] dkms -- dkms-build quieten wget verbiage
+
+  * tsc marked unstable after entered PC10 on Intel CoffeeLake (LP: #1840239)
+    - SAUCE: x86/intel: Disable HPET on Intel Coffe Lake platforms
+    - SAUCE: x86/intel: Disable HPET on Intel Ice Lake platforms
+
+  * shiftfs: prevent exceeding project quotas (LP: #1849483)
+    - SAUCE: shiftfs: drop CAP_SYS_RESOURCE from effective capabilities
+
+  * shiftfs: fix fallocate() (LP: #1849482)
+    - SAUCE: shiftfs: setup correct s_maxbytes limit
+
+  * The alsa hda driver is not loaded due to the missing of PCIID for Comet
+    Lake-S [8086:a3f0] (LP: #1852070)
+    - SAUCE: ALSA: hda: Add Cometlake-S PCI ID
+
+  * Can't adjust brightness on DELL UHD dGPU AIO (LP: #1813877)
+    - SAUCE: platform/x86: dell-uart-backlight: add missing status command
+    - SAUCE: platform/x86: dell-uart-backlight: load driver by scalar status
+    - SAUCE: platform/x86: dell-uart-backlight: add force parameter
+    - SAUCE: platform/x86: dell-uart-backlight: add quirk for old platforms
+
+  * s_iflags overlap prevents unprivileged overlayfs mounts (LP: #1851677)
+    - SAUCE: fs: Move SB_I_NOSUID to the top of s_iflags
+
+  * ubuntu-aufs-modified mmap_region() breaks refcounting in overlayfs/shiftfs
+    error path (LP: #1850994) // CVE-2019-15794
+    - SAUCE: shiftfs: Restore vm_file value when lower fs mmap fails
+    - SAUCE: ovl: Restore vm_file value when lower fs mmap fails
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Convert update-aufs.sh to use aufs5
+    - SAUCE: import aufs driver
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 13 Nov 2019 11:56:35 -0800
+
+linux (5.4.0-4.5) focal; urgency=medium
+
+  * High power consumption using 5.0.0-25-generic (LP: #1840835)
+    - PCI: Add a helper to check Power Resource Requirements _PR3 existence
+    - ALSA: hda: Allow HDA to be runtime suspended when dGPU is not bound to a
+      driver
+    - PCI: Fix missing inline for pci_pr3_present()
+
+  * Fix signing of staging modules in eoan (LP: #1850234)
+    - [Packaging] Leave unsigned modules unsigned after adding .gnu_debuglink
+
+  * [20.04 FEAT] Set Architecture Level (ALS) to z13 (LP: #1837525)
+    - [Config] s390x bump march to z13, with tune to z15
+
+  * Miscellaneous Ubuntu changes
+    - [Debian]: do not skip tests for linux-hwe-edge
+    - update dkms package versions
+    - [Config] re-enable zfs
+    - [Config] rename module virtio_fs to virtiofs
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc6
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 04 Nov 2019 15:12:02 +0100
+
+linux (5.4.0-3.4) focal; urgency=medium
+
+  * seccomp: fix SECCOMP_USER_NOTIF_FLAG_CONTINUE test (LP: #1849281)
+    - SAUCE: seccomp: fix SECCOMP_USER_NOTIF_FLAG_CONTINUE test
+
+  * cloudimg: no iavf/i40evf module so no network available with SR-IOV enabled
+    cloud (LP: #1848481)
+    - [Packaging] include iavf/i40evf in generic
+
+  * CVE-2019-17666
+    - SAUCE: rtlwifi: Fix potential overflow on P2P code
+
+  * Change Config Option CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE for s390x from yes
+    to no (LP: #1848492)
+    - [Config] Change Config Option CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE for s390x
+      from yes to no
+
+  * Add Intel Comet Lake ethernet support (LP: #1848555)
+    - SAUCE: e1000e: Add support for Comet Lake
+
+  * seccomp: add SECCOMP_USER_NOTIF_FLAG_CONTINUE    (LP: #1847744)
+    - SAUCE: seccomp: add SECCOMP_USER_NOTIF_FLAG_CONTINUE
+    - SAUCE: seccomp: test SECCOMP_USER_NOTIF_FLAG_CONTINUE
+
+  * drm/i915: Fix the issue of "azx_get_response timeout" for hdmi audio on ICL
+    platforms (LP: #1847192)
+    - SAUCE: drm/i915: Fix audio power up sequence for gen10+ display
+    - SAUCE: drm/i915: extend audio CDCLK>=2*BCLK constraint to more platforms
+
+  * PM / hibernate: fix potential memory corruption (LP: #1847118)
+    - SAUCE: PM / hibernate: memory_bm_find_bit -- tighten node optimisation
+
+  * [regression] NoNewPrivileges incompatible with Apparmor (LP: #1844186)
+    - SAUCE: apparmor: fix nnp subset test for unconfined
+
+  * overlayfs: allow with shiftfs as underlay (LP: #1846272)
+    - SAUCE: overlayfs: allow with shiftfs as underlay
+
+  * eoan: alsa/sof: Enable SOF_HDA link and codec (LP: #1848490)
+    - [Config] Fix SOF Kconfig options
+
+  * linux won't build when new virtualbox version is present on the archive
+    (LP: #1848788)
+    - [Packaging]: download virtualbox from sources
+
+  * Miscellaneous Ubuntu changes
+    - [Config] update annotations from configs
+    - [Config] updateconfigs after rebase to 5.4-rc5
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 29 Oct 2019 12:01:27 -0500
+
+linux (5.4.0-2.3) eoan; urgency=medium
+
+  * Add installer support for iwlmvm adapters (LP: #1848236)
+    - d-i: Add iwlmvm to nic-modules
+
+  * shiftfs: rework how shiftfs opens files (LP: #1846265)
+    - SAUCE: shiftfs: rework how shiftfs opens files
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.4-rc4
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc4
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 21 Oct 2019 17:31:26 +0200
+
+linux (5.4.0-1.2) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - [Config] updateconfigs after rebase to 5.4-rc3
+    - [Config] add flexfb, fbtft_device and rio500 to modules.ignore
+    - [Config] amd64: ignore fbtft and all dependent modules
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc3
+
+ -- Andrea Righi <andrea.righi@canonical.com>  Mon, 14 Oct 2019 19:48:52 +0200
+
+linux (5.4.0-0.1) eoan; urgency=medium
+
+  * Enable the Dragonboards out of Eoan/master arm64 kernel (LP: #1846704)
+    - [Packaging] arm64: snapdragon: introduce a snapdragon flavour
+    - [Packaging] arm64: snapdragon: switch kernel format to Image
+    - [Config] arm64: snapdragon: CONFIG_PINCTRL_MSM8916=y
+    - [Config] arm64: snapdragon: CONFIG_PINCTRL_MSM8994=y
+    - [Config] arm64: snapdragon: CONFIG_PINCTRL_MSM8996=y
+    - [Config] arm64: snapdragon: CONFIG_PINCTRL_MSM8998=y
+    - [Config] arm64: snapdragon: CONFIG_REGULATOR_QCOM_RPMH=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_BAM_DMA=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_HIDMA_MGMT=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_HIDMA=y
+    - [Config] arm64: snapdragon: CONFIG_COMMON_CLK_QCOM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_CLK_RPMH=y
+    - [Config] arm64: snapdragon: CONFIG_MSM_GCC_8916=y
+    - [Config] arm64: snapdragon: CONFIG_MSM_GCC_8994=y
+    - [Config] arm64: snapdragon: CONFIG_MSM_MMCC_8996=y
+    - [Config] arm64: snapdragon: CONFIG_MSM_GCC_8998=y
+    - [Config] arm64: snapdragon: CONFIG_HWSPINLOCK_QCOM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_APCS_IPC=y
+    - [Config] arm64: snapdragon: CONFIG_RPMSG_QCOM_GLINK_RPM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_GENI_SE=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_SMEM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_SMD_RPM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_SMP2P=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_SMSM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_QFPROM=y
+    - [Config] arm64: snapdragon: CONFIG_SERIAL_QCOM_GENI=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_TSENS=y
+    - [Config] arm64: snapdragon: CONFIG_REGULATOR_QCOM_SMD_RPM=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_CLK_SMD_RPM=y
+    - [Config] arm64: snapdragon: CONFIG_RPMSG_QCOM_SMD=y
+    - [Config] arm64: snapdragon: CONFIG_MFD_QCOM_RPM=y
+    - [Config] arm64: snapdragon: CONFIG_SCSI_UFSHCD=y
+    - [Config] arm64: snapdragon: CONFIG_SCSI_UFSHCD_PLATFORM=y
+    - [Config] arm64: snapdragon: CONFIG_SCSI_UFS_HISI=y
+    - [Config] arm64: snapdragon: CONFIG_MMC_SDHCI=y
+    - [Config] arm64: snapdragon: CONFIG_MMC_SDHCI_PLTFM=y
+    - [Config] arm64: snapdragon: CONFIG_MMC_SDHCI_MSM=y
+    - [Config] arm64: snapdragon: CONFIG_REGULATOR_QCOM_SPMI=y
+    - [Config] arm64: snapdragon: CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
+    - [Config] arm64: snapdragon: CONFIG_PHY_QCOM_USB_HS=y
+    - [Config] arm64: snapdragon: CONFIG_PHY_QCOM_QMP=y
+    - [Config] arm64: snapdragon: CONFIG_PHY_QCOM_UFS=y
+    - [Config] arm64: snapdragon: CONFIG_PHY_QCOM_USB_HSIC=y
+    - [Config] arm64: snapdragon: CONFIG_USB_CHIPIDEA_OF=y
+    - [Config] arm64: snapdragon: CONFIG_USB_EHCI_HCD_PLATFORM=y
+    - [Config] arm64: snapdragon: CONFIG_EXTCON_USB_GPIO=y
+    - [Config] arm64: snapdragon: CONFIG_REGULATOR_FIXED_VOLTAGE=y
+    - [Config] arm64: snapdragon: CONFIG_LEDS_GPIO=y
+    - [Config] arm64: snapdragon: CONFIG_USB_HSIC_USB3503=y
+    - [Config] arm64: snapdragon: CONFIG_USB_NET_DRIVERS=y
+    - [Config] arm64: snapdragon: CONFIG_USB_OTG=y
+    - [Config] arm64: snapdragon: CONFIG_USB_XHCI_PLATFORM=y
+    - [Config] arm64: snapdragon: CONFIG_USB_OHCI_HCD_PLATFORM=y
+    - [Config] arm64: snapdragon: CONFIG_USB_MUSB_HDRC=y
+    - [Config] arm64: snapdragon: CONFIG_USB_DWC3=y
+    - [Config] arm64: snapdragon: CONFIG_USB_DWC3_PCI=y
+    - [Config] arm64: snapdragon: CONFIG_USB_DWC3_OF_SIMPLE=y
+    - [Config] arm64: snapdragon: CONFIG_USB_DWC3_QCOM=y
+    - [Config] arm64: snapdragon: CONFIG_LEDS_PWM=y
+    - [Config] arm64: snapdragon: CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+    - [Config] arm64: snapdragon: CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_A53PLL=y
+    - [Config] arm64: snapdragon: CONFIG_QCOM_CLK_APCS_MSM8916=y
+    - [Config] arm64: snapdragon: CONFIG_NLS_ISO8859_1=y
+    - [Config] arm64: snapdragon: CONFIG_USB_USBNET=y
+    - [Config] arm64: snapdragon: CONFIG_CRYPTO_DEV_QCOM_RNG=y
+    - [Config] arm64: snapdragon: CONFIG_POWER_RESET_QCOM_PON=y
+    - [Config] arm64: snapdragon: CONFIG_INPUT_PM8941_PWRKEY=y
+    - [Config] arm64: snapdragon: CONFIG_KEYBOARD_GPIO=y
+    - [Config] arm64: snapdragon: CONFIG_RTC_DRV_PM8XXX=y
+
+  * Miscellaneous Ubuntu changes
+    - [Config] updateconfigs after rebase to 5.4-rc2
+    - SAUCE: (lockdown) Make get_cert_list() not complain about cert lists that
+      aren't present.
+    - SAUCE: (lockdown) Add efi_status_to_str() and rework efi_status_to_err().
+    - SAUCE: (lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (lockdown) security: lockdown: expose a hook to lock the kernel down
+    - SAUCE: (lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure boot
+      mode
+    - SAUCE: (lockdown) efi: Lock down the kernel if booted in secure boot mode
+    - SAUCE: (lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (lockdown) KEYS: Make use of platform keyring for module signature
+      verify
+    - SAUCE: (lockdown) arm64: Allow locking down the kernel under EFI secure boot
+    - SAUCE: (lockdown) security: lockdown: Make
+      CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT more generic
+    - SAUCE: (lockdown) s390/ipl: lockdown kernel when booted secure
+    - [Config] Enable lockdown under secure boot
+    - SAUCE: import aufs driver
+    - SAUCE: aufs: rwsem owner changed to atmoic_long_t in 5.3
+    - SAUCE: aufs: add "WITH Linux-syscall-note" to SPDX tag of uapi headers
+    - [Config] enable aufs
+    - update dkms package versions
+    - [Config] disable zfs
+    - [Config] disable nvidia dkms build
+    - [Config] disable virtualbox dkms build
+    - [Debian] Generate stub reconstruct for -rc kernels
+    - Revert "UBUNTU: SAUCE: (namespace) block_dev: Forbid unprivileged mounting
+      when device is opened for writing"
+    - Revert "UBUNTU: SAUCE: (namespace) ext4: Add module parameter to enable user
+      namespace mounts"
+    - Revert "UBUNTU: SAUCE: (namespace) ext4: Add support for unprivileged mounts
+      from user namespaces"
+    - Revert "UBUNTU: SAUCE: (namespace) mtd: Check permissions towards mtd block
+      device inode when mounting"
+    - Revert "UBUNTU: SAUCE: (namespace) block_dev: Check permissions towards
+      block device inode when mounting"
+    - Revert "UBUNTU: SAUCE: (namespace) block_dev: Support checking inode
+      permissions in lookup_bdev()"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.4-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 11 Oct 2019 16:42:41 -0500
+
+linux (5.4.0-0.0) eoan; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 08 Oct 2019 09:59:00 -0500
+
+linux (5.3.0-17.18) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-17.18 -proposed tracker (LP: #1846641)
+
+  * CVE-2019-17056
+    - nfc: enforce CAP_NET_RAW for raw sockets
+
+  * CVE-2019-17055
+    - mISDN: enforce CAP_NET_RAW for raw sockets
+
+  * CVE-2019-17054
+    - appletalk: enforce CAP_NET_RAW for raw sockets
+
+  * CVE-2019-17053
+    - ieee802154: enforce CAP_NET_RAW for raw sockets
+
+  * CVE-2019-17052
+    - ax25: enforce CAP_NET_RAW for raw sockets
+
+  * CVE-2019-15098
+    - ath6kl: fix a NULL-ptr-deref bug in ath6kl_usb_alloc_urb_from_pipe()
+
+  * xHCI on AMD Stoney Ridge cannot detect USB 2.0 or 1.1 devices.
+    (LP: #1846470)
+    - x86/PCI: Avoid AMD FCH XHCI USB PME# from D0 defect
+
+  * Re-enable linux-libc-dev build on i386 (LP: #1846508)
+    - [Packaging] Build only linux-libc-dev for i386
+    - [Debian] final-checks -- ignore archtictures with no binaries
+
+  * arm64: loop on boot after installing linux-generic-hwe-18.04-edge/bionic-
+    proposed (LP: #1845820)
+    - [Config] Disable CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT
+
+  * Revert ESE DASD discard support (LP: #1846219)
+    - SAUCE: Revert "s390/dasd: Add discard support for ESE volumes"
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 03 Oct 2019 16:57:05 -0500
+
+linux (5.3.0-16.17) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-16.17 -proposed tracker (LP: #1846204)
+
+  * zfs fails to build on s390x  with debug symbols enabled (LP: #1846143)
+    - SAUCE: s390: Mark atomic const ops always inline
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 01 Oct 2019 07:46:43 -0500
+
+linux (5.3.0-15.16) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-15.16 -proposed tracker (LP: #1845987)
+
+  * Drop i386 build for 19.10 (LP: #1845714)
+    - [Packaging] Remove x32 arch references from control files
+    - [Debian] final-checks -- Get arch list from debian/control
+
+  * ZFS kernel modules lack debug symbols (LP: #1840704)
+    - [Debian] Fix conditional for setting zfs debug package path
+
+  * Use pyhon3-sphinx instead of python-sphinx for building html docs
+    (LP: #1845808)
+    - [Packaging] Update sphinx build dependencies to python3 packages
+
+  * Kernel panic with 19.10 beta image (LP: #1845454)
+    - efi/tpm: Don't access event->count when it isn't mapped.
+    - efi/tpm: don't traverse an event log with no events
+    - efi/tpm: only set efi_tpm_final_log_size after successful event log parsing
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 30 Sep 2019 11:57:20 -0500
+
+linux (5.3.0-14.15) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-14.15 -proposed tracker (LP: #1845728)
+
+  * Drop i386 build for 19.10 (LP: #1845714)
+    - [Debian] Remove support for producing i386 kernels
+    - [Debian] Don't use CROSS_COMPILE for i386 configs
+
+  * udevadm trigger will fail when trying to add /sys/devices/vio/
+    (LP: #1845572)
+    - SAUCE: powerpc/vio: drop bus_type from parent device
+
+  * Trying to online dasd drive results in invalid input/output from the kernel
+    on z/VM (LP: #1845323)
+    - SAUCE: s390/dasd: Fix error handling during online processing
+
+  * intel-lpss driver conflicts with write-combining MTRR region (LP: #1845584)
+    - SAUCE: mfd: intel-lpss: add quirk for Dell XPS 13 7390 2-in-1
+
+  * Support Hi1620 zip hw accelerator (LP: #1845355)
+    - [Config] Enable HiSilicon QM/ZIP as modules
+    - crypto: hisilicon - add queue management driver for HiSilicon QM module
+    - crypto: hisilicon - add hardware SGL support
+    - crypto: hisilicon - add HiSilicon ZIP accelerator support
+    - crypto: hisilicon - add SRIOV support for ZIP
+    - Documentation: Add debugfs doc for hisi_zip
+    - crypto: hisilicon - add debugfs for ZIP and QM
+    - MAINTAINERS: add maintainer for HiSilicon QM and ZIP controller driver
+    - crypto: hisilicon - fix kbuild warnings
+    - crypto: hisilicon - add dependency for CRYPTO_DEV_HISI_ZIP
+    - crypto: hisilicon - init curr_sgl_dma to fix compile warning
+    - crypto: hisilicon - add missing single_release
+    - crypto: hisilicon - fix error handle in hisi_zip_create_req_q
+    - crypto: hisilicon - Fix warning on printing %p with dma_addr_t
+    - crypto: hisilicon - Fix return value check in hisi_zip_acompress()
+    - crypto: hisilicon - avoid unused function warning
+
+  * SafeSetID LSM should be built but disabled by default (LP: #1845391)
+    - LSM: SafeSetID: Stop releasing uninitialized ruleset
+    - [Config] Build SafeSetID LSM but don't enable it by default
+
+  * CONFIG_LSM should not specify loadpin since it is not built (LP: #1845383)
+    - [Config] loadpin shouldn't be in CONFIG_LSM
+
+  * Add new pci-id's for CML-S, ICL (LP: #1845317)
+    - drm/i915/icl: Add missing device ID
+    - drm/i915/cml: Add Missing PCI IDs
+
+  * Thunderbolt support for ICL (LP: #1844680)
+    - thunderbolt: Correct path indices for PCIe tunnel
+    - thunderbolt: Move NVM upgrade support flag to struct icm
+    - thunderbolt: Use 32-bit writes when writing ring producer/consumer
+    - thunderbolt: Do not fail adding switch if some port is not implemented
+    - thunderbolt: Hide switch attributes that are not set
+    - thunderbolt: Expose active parts of NVM even if upgrade is not supported
+    - thunderbolt: Add support for Intel Ice Lake
+    - ACPI / property: Add two new Thunderbolt property GUIDs to the list
+
+  * Ubuntu 19.10 -  Additional PCI patch and fix (LP: #1844668)
+    - s390/pci: fix MSI message data
+
+  * Enhanced Hardware Support - Finalize Naming (LP: #1842774)
+    - s390: add support for IBM z15 machines
+    - [Config] CONFIG_MARCH_Z15=n, CONFIG_TUNE_Z15=n
+
+  * Eoan update: v5.3.1 upstream stable release (LP: #1845642)
+    - USB: usbcore: Fix slab-out-of-bounds bug during device reset
+    - media: tm6000: double free if usb disconnect while streaming
+    - phy: renesas: rcar-gen3-usb2: Disable clearing VBUS in over-current
+    - ip6_gre: fix a dst leak in ip6erspan_tunnel_xmit
+    - net/sched: fix race between deactivation and dequeue for NOLOCK qdisc
+    - net_sched: let qdisc_put() accept NULL pointer
+    - udp: correct reuseport selection with connected sockets
+    - xen-netfront: do not assume sk_buff_head list is empty in error handling
+    - net: dsa: Fix load order between DSA drivers and taggers
+    - net: stmmac: Hold rtnl lock in suspend/resume callbacks
+    - KVM: coalesced_mmio: add bounds checking
+    - Documentation: sphinx: Add missing comma to list of strings
+    - firmware: google: check if size is valid when decoding VPD data
+    - serial: sprd: correct the wrong sequence of arguments
+    - tty/serial: atmel: reschedule TX after RX was started
+    - nl80211: Fix possible Spectre-v1 for CQM RSSI thresholds
+    - Revert "arm64: Remove unnecessary ISBs from set_{pte,pmd,pud}"
+    - ovl: fix regression caused by overlapping layers detection
+    - phy: qcom-qmp: Correct ready status, again
+    - floppy: fix usercopy direction
+    - media: technisat-usb2: break out of loop at end of buffer
+    - Linux 5.3.1
+
+  * ZFS kernel modules lack debug symbols (LP: #1840704)
+    - [Debian]: Remove hardcoded $(pkgdir) in debug symbols handling
+    - [Debian]: Handle debug symbols for modules in extras too
+    - [Debian]: Check/link modules with debug symbols after DKMS modules
+    - [Debian]: Warn about modules without debug symbols
+    - [Debian]: dkms-build: new parameter for debug package directory
+    - [Debian]: dkms-build: zfs: support for debug symbols
+    - [Debian]: dkms-build: Avoid executing post-processor scripts twice
+    - [Debian]: dkms-build: Move zfs special-casing into configure script
+
+  * /proc/self/maps paths missing on live session (was vlc won't start; eoan
+    19.10 & bionic 18.04 ubuntu/lubuntu/kubuntu/xubuntu/ubuntu-mate dailies)
+    (LP: #1842382)
+    - SAUCE: Revert "UBUNTU: SAUCE: shiftfs: enable overlayfs on shiftfs"
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 27 Sep 2019 16:08:06 -0500
+
+linux (5.3.0-13.14) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-13.14 -proposed tracker (LP: #1845105)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Remove binutils-dev build dependency
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 23 Sep 2019 19:26:43 -0500
+
+linux (5.3.0-12.13) eoan; urgency=medium
+
+  * Change kernel compression method to improve boot speed (LP: #1840934)
+    - [Packaging] Add lz4 build dependency for s390x
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Remove spl and zfs source
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 17 Sep 2019 13:36:26 +0200
+
+linux (5.3.0-11.12) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-11.12 -proposed tracker (LP: #1844144)
+
+  *  Suspend to RAM(S3) does not wake up for latest megaraid and mpt3sas
+    adapters(SAS3.5 onwards) (LP: #1838751)
+    - PCI: Restore Resizable BAR size bits correctly for 1MB BARs
+
+  * s390/setup: Actually init kernel lock down (LP: #1843961)
+    - SAUCE: (lockdown) s390/setup: Actually init kernel lock down
+
+  * cherrypick has_sipl fix (LP: #1843960)
+    - SAUCE: s390/sclp: Fix bit checked for has_sipl
+
+  * Change kernel compression method to improve boot speed (LP: #1840934)
+    - [Config]: Switch kernel compression from LZO to LZ4 on s390x
+
+  * Installation fails on eoan/PowerVM : missing /dev/nvram (LP: #1837726)
+    - [Config] CONFIG_NVRAM=y for ppc64el
+
+  * Miscellaneous Ubuntu changes
+    - [Config]: remove nvram from ppc64el modules ABI
+    - [Config] Update annotations for recent config changes
+    - SAUCE: sched: Add __ASSEMBLY__ guards around struct clone_args
+    - SAUCE: i2c: qcom-geni: Disable DMA processing on the Lenovo Yoga C630
+    - SAUCE: arm64: dts: qcom: Add Lenovo Yoga C630
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 16 Sep 2019 16:18:27 +0200
+
+linux (5.3.0-10.11) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-10.11 -proposed tracker (LP: #1843232)
+
+  * No sound inputs from the external microphone and headset on a Dell machine
+    (LP: #1842265)
+    - SAUCE: ALSA: hda - Expand pin_match function to match upcoming new tbls
+    - SAUCE: ALSA: hda - Define a fallback_pin_fixup_tbl for alc269 family
+
+  * Horizontal corrupted line at top of screen caused by framebuffer compression
+    (LP: #1840236)
+    - SAUCE: drm/i915/fbc: disable framebuffer compression on IceLake
+
+  * Add bpftool to linux-tools-common (LP: #1774815)
+    - [Debian] package bpftool in linux-tools-common
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc8
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 09 Sep 2019 10:00:41 +0200
+
+linux (5.3.0-9.10) eoan; urgency=medium
+
+  * eoan/linux: 5.3.0-9.10 -proposed tracker (LP: #1842393)
+
+  * shiftfs: mark kmem_cache as reclaimable (LP: #1842059)
+    - SAUCE: shiftfs: mark slab objects SLAB_RECLAIM_ACCOUNT
+
+  * shiftfs: drop entries from cache on unlink (LP: #1841977)
+    - SAUCE: shiftfs: fix buggy unlink logic
+
+  * Fix touchpad IRQ storm after S3 (LP: #1841396)
+    - pinctrl: intel: remap the pin number to gpio offset for irq enabled pin
+
+  * Please include DTBs for arm64 laptops (LP: #1842050)
+    - arm64: dts: qcom: Add Lenovo Miix 630
+    - arm64: dts: qcom: Add HP Envy x2
+    - arm64: dts: qcom: Add Asus NovaGo TP370QL
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: import aufs driver
+    - [Packaging]: ignore vbox modules when vbox is disabled
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc7
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Tue, 03 Sep 2019 10:27:33 +0200
+
+linux (5.3.0-8.9) eoan; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync getabis
+
+  * Change kernel compression method to improve boot speed (LP: #1840934)
+    - [Config] change kernel compression method to improve boot speed
+    - [Packaging] add build dependencies for compression algorithms
+
+  * realtek r8822be kernel module fails after update to linux kernel-headers
+    5.0.0-21 (LP: #1838133)
+    - rtw88: Fix misuse of GENMASK macro
+    - rtw88: pci: Rearrange the memory usage for skb in RX ISR
+    - rtw88: pci: Use DMA sync instead of remapping in RX ISR
+    - rtw88: debug: dump tx power indexes in use
+    - rtw88: use txpwr_lmt_cfg_pair struct, not arrays
+    - rtw88: pci: remove set but not used variable 'ip_sel'
+    - rtw88: allow c2h operation in irq context
+    - rtw88: enclose c2h cmd handle with mutex
+    - rtw88: add BT co-existence support
+    - SAUCE: rtw88: pci: enable MSI interrupt
+
+  * VIMC module not available (CONFIG_VIDEO_VIMC not set) (LP: #1831482)
+    - [Config] Enable VIMC module
+
+  * Goodix touchpad may drop first input event (LP: #1840075)
+    - Revert "UBUNTU: SAUCE: i2c: designware: add G3 3590 into i2c quirk"
+    - Revert "UBUNTU: SAUCE: i2c: designware: add Inpiron 7591 into i2c quirk"
+    - Revert "UBUNTU: SAUCE: i2c: designware: add Inpiron/Vostro 7590 into i2c
+      quirk"
+    - Revert "UBUNTU: SAUCE: i2c: designware: Add disable runtime pm quirk"
+    - mfd: intel-lpss: Remove D3cold delay
+
+  * Include Sunix serial/parallel driver (LP: #1826716)
+    - serial: 8250_pci: Add support for Sunix serial boards
+    - parport: parport_serial: Add support for Sunix Multi I/O boards
+
+  * enable lockdown on s390x when Secure IPL is performed (LP: #1839622)
+    - SAUCE: (lockdown) s390/ipl: lockdown kernel when booted secure
+    - Ubuntu: [Config] Enable CONFIG_LOCK_DOWN_KERNEL on s390x.
+
+  * UBUNTU: SAUCE: shiftfs: pass correct point down (LP: #1837231)
+    - SAUCE: shiftfs: pass correct point down
+
+  * shiftfs: add O_DIRECT support (LP: #1837223)
+    - SAUCE: shiftfs: add O_DIRECT support
+
+  * Miscellaneous Ubuntu changes
+    - [Config] enable secureboot signing on s390x
+    - [Config] CONFIG_TEST_BLACKHOLE_DEV=m
+    - SAUCE: selftests: fib_tests: assign address to dummy1 for rp_filter tests
+    - [Debian] disable dkms builds for autopktest rebuilds
+    - update dkms package versions
+    - [Config] updateconfigs after v5.3-rc6 rebase
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc5
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 26 Aug 2019 10:09:42 +0200
+
+linux (5.3.0-7.8) eoan; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync getabis
+
+  * Miscellaneous Ubuntu changes
+    - [Config] updateconfigs after v5.3-rc5 rebase
+    - remove missing module after updateconfigs
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc5
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 19 Aug 2019 15:31:24 +0200
+
+linux (5.3.0-6.7) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests/bpf: prevent headers to be compiled as C code
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 14 Aug 2019 13:25:01 -0500
+
+linux (5.3.0-5.6) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - [Config] enable zfs build
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 13 Aug 2019 09:16:06 -0500
+
+linux (5.3.0-4.5) eoan; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync getabis
+    - [Packaging] update helper scripts
+
+  * bcache: bch_allocator_thread(): hung task timeout (LP: #1784665) // Tight
+    timeout for bcache removal causes spurious failures (LP: #1796292)
+    - SAUCE: bcache: fix deadlock in bcache_allocator
+
+  * shiftfs: allow overlayfs (LP: #1838677)
+    - SAUCE: shiftfs: enable overlayfs on shiftfs
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "kbuild: modpost: do not parse unnecessary rules for vmlinux
+      modpost"
+    - update dkms package versions
+    - enable nvidia dkms build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 12 Aug 2019 10:41:27 -0500
+
+linux (5.3.0-3.4) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - SAUCE: aufs: add "WITH Linux-syscall-note" to SPDX tag of uapi headers
+    - [Config] add mux-* to modules.ignore
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc3
+
+ -- Paolo Pisati <paolo.pisati@canonical.com>  Mon, 05 Aug 2019 18:17:09 +0200
+
+linux (5.3.0-2.3) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] add build dependincy on fontconfig
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 29 Jul 2019 12:18:46 -0400
+
+linux (5.3.0-1.2) eoan; urgency=medium
+
+  * System does not auto detect disconnection of external monitor (LP: #1835001)
+    - SAUCE: drm/i915: Add support for retrying hotplug
+    - SAUCE: drm/i915: Enable hotplug retry
+
+  * Please enable CONFIG_SCSI_UFS_QCOM as a module on arm64 (LP: #1837332)
+    - [Config] Enable CONFIG_SCSI_UFS_QCOM as a module on arm64.
+
+  * Add arm64 CONFIG_ARCH_MESON=y and related configs Edit (LP: #1820530)
+    - [Config] enable ARCH_MESON
+    - remove missing module
+    - [Config] update annotations after enabling ARCH_MESON for arm64
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: KVM: PPC: comment implicit fallthrough
+    - update dkms package versions
+    - [Config] enable vbox dkms build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 28 Jul 2019 23:10:16 -0400
+
+linux (5.3.0-0.1) eoan; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) kexec_file: split KEXEC_VERIFY_SIG into KEXEC_SIG and
+      KEXEC_SIG_FORCE
+    - SAUCE: (efi-lockdown) kexec_file: Restrict at runtime if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Lock down module params that specify hardware
+      parameters (eg. ioport)
+    - SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the testmmiotrace module
+    - SAUCE: (efi-lockdown) Lock down /proc/kcore
+    - SAUCE: (efi-lockdown) Lock down kprobes
+    - SAUCE: (efi-lockdown) bpf: Restrict kernel image access functions when the
+      kernel is locked down
+    - SAUCE: (efi-lockdown) Lock down perf
+    - SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) lockdown: Print current->comm in restriction messages
+    - SAUCE: (efi-lockdown) kexec: Allow kexec_file() with appropriate IMA policy
+      when locked down
+    - SAUCE: (efi-lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (efi-lockdown) debugfs: avoid EPERM when no open file operation
+      defined
+    - SAUCE: (efi-lockdown) Make get_cert_list() not complain about cert lists
+      that aren't present.
+    - SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err().
+    - SAUCE: (efi-lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) KEYS: Make use of platform keyring for module
+      signature verify
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) furter KEXEC_VERIFY_SIG -> KEXEC_SIG updates
+    - SAUCE: (efi-lockdown) arm64: add kernel config option to lock down when in
+      Secure Boot mode
+    - SAUCE: import aufs driver
+    - SAUCE: aufs: rwsem owner changed to atmoic_long_t in 5.3
+    - [Config] disable zfs dkms build
+    - [Config] disable nvidia dkms build
+    - [Config] disable vbox dkms build
+    - SAUCE: perf diff: use llabs for s64 vaules
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.3-rc1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 23 Jul 2019 21:45:44 -0500
+
+linux (5.3.0-0.0) eoan; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 22 Jul 2019 10:19:04 -0500
+
+linux (5.2.0-9.10) eoan; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * input/mouse: alps trackpoint-only device doesn't work (LP: #1836752)
+    - SAUCE: Input: alps - don't handle ALPS cs19 trackpoint-only device
+    - SAUCE: Input: alps - fix a mismatch between a condition check and its
+      comment
+
+  * System does not auto detect disconnection of external monitor (LP: #1835001)
+    - SAUCE: drm/i915: Add support for retrying hotplug
+    - SAUCE: drm/i915: Enable hotplug retry
+
+  * alsa/hdmi: add icelake hdmi audio support for a Dell machine (LP: #1836916)
+    - SAUCE: ALSA: hda/hdmi - Remove duplicated define
+    - SAUCE: ALSA: hda/hdmi - Fix i915 reverse port/pin mapping
+
+  * First click on Goodix touchpad doesn't be recognized after runtime suspended
+    (LP: #1836836)
+    - SAUCE: i2c: designware: add G3 3590 into i2c quirk
+
+  * ixgbe{vf} - Physical Function gets IRQ when VF checks link state
+    (LP: #1836760)
+    - ixgbevf: Use cached link state instead of re-reading the value for ethtool
+
+  * Doing multiple squashfs (and other loop?) mounts in parallel breaks
+    (LP: #1836914)
+    - SAUCE: Revert "loop: Don't change loop device under exclusive opener"
+
+  * hibmc-drm Causes Unreadable Display for Huawei amd64 Servers (LP: #1762940)
+    - SAUCE: Make CONFIG_DRM_HISI_HIBMC depend on ARM64
+    - [Config] Set CONFIG_DRM_HISI_HIBMC to arm64 only
+    - [Config] add hibmc-drm to modules.ignore
+
+  * hda/realtek: can't detect external mic on a Dell machine (LP: #1836755)
+    - ALSA: hda/realtek: apply ALC891 headset fixup to one Dell machine
+
+  * Enable Armada SOCs and MVPP2 NIC driver for disco/generic arm64
+    (LP: #1835054)
+    - [Config] Enable Armada SOCs and MVPP2 NIC driver for disco/generic arm64
+
+  * Unhide Nvidia HDA audio controller (LP: #1836308)
+    - PCI: Enable NVIDIA HDA controllers
+
+  * Intel ethernet I219 may wrongly detect connection speed as 10Mbps
+    (LP: #1836177)
+    - e1000e: Make watchdog use delayed work
+
+  * Sometimes touchpad(goodix) can't use tap function (LP: #1836020)
+    - SAUCE: i2c: designware: add Inpiron/Vostro 7590 into i2c quirk
+    - SAUCE: i2c: designware: add Inpiron 7591 into i2c quirk
+
+  * Intel ethernet I219 has slow RX speed (LP: #1836152)
+    - e1000e: add workaround for possible stalled packet
+    - e1000e: disable force K1-off feature
+
+  * bcache: risk of data loss on I/O errors in backing or caching devices
+    (LP: #1829563)
+    - Revert "bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()"
+
+  * bnx2x driver causes 100% CPU load (LP: #1832082)
+    - bnx2x: Prevent ptp_task to be rescheduled indefinitely
+
+  * fcf-protection=none patch with new version
+    - Revert "UBUNTU: SAUCE: kbuild: add -fcf-protection=none to retpoline flags"
+    - SAUCE: kbuild: add -fcf-protection=none when using retpoline flags
+
+  * CVE-2019-12614
+    - powerpc/pseries/dlpar: Fix a missing check in dlpar_parse_cc_property()
+
+  * Eoan update: v5.2.1 upstream stable release (LP: #1836622)
+    - crypto: lrw - use correct alignmask
+    - crypto: talitos - rename alternative AEAD algos.
+    - fscrypt: don't set policy for a dead directory
+    - udf: Fix incorrect final NOT_ALLOCATED (hole) extent length
+    - media: stv0297: fix frequency range limit
+    - ALSA: usb-audio: Fix parse of UAC2 Extension Units
+    - ALSA: hda/realtek - Headphone Mic can't record after S3
+    - tpm: Actually fail on TPM errors during "get random"
+    - tpm: Fix TPM 1.2 Shutdown sequence to prevent future TPM operations
+    - block: fix .bi_size overflow
+    - block, bfq: NULL out the bic when it's no longer valid
+    - perf intel-pt: Fix itrace defaults for perf script
+    - perf auxtrace: Fix itrace defaults for perf script
+    - perf intel-pt: Fix itrace defaults for perf script intel-pt documentation
+    - perf pmu: Fix uncore PMU alias list for ARM64
+    - perf thread-stack: Fix thread stack return from kernel for kernel-only case
+    - perf header: Assign proper ff->ph in perf_event__synthesize_features()
+    - x86/ptrace: Fix possible spectre-v1 in ptrace_get_debugreg()
+    - x86/tls: Fix possible spectre-v1 in do_get_thread_area()
+    - Documentation: Add section about CPU vulnerabilities for Spectre
+    - Documentation/admin: Remove the vsyscall=native documentation
+    - mwifiex: Don't abort on small, spec-compliant vendor IEs
+    - USB: serial: ftdi_sio: add ID for isodebug v1
+    - USB: serial: option: add support for GosunCn ME3630 RNDIS mode
+    - Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
+    - p54usb: Fix race between disconnect and firmware loading
+    - usb: gadget: f_fs: data_len used before properly set
+    - usb: gadget: ether: Fix race between gether_disconnect and rx_submit
+    - usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
+    - usb: renesas_usbhs: add a workaround for a race condition of workqueue
+    - drivers/usb/typec/tps6598x.c: fix portinfo width
+    - drivers/usb/typec/tps6598x.c: fix 4CC cmd write
+    - p54: fix crash during initialization
+    - staging: comedi: dt282x: fix a null pointer deref on interrupt
+    - staging: wilc1000: fix error path cleanup in wilc_wlan_initialize()
+    - staging: bcm2835-camera: Restore return behavior of ctrl_set_bitrate()
+    - staging: comedi: amplc_pci230: fix null pointer deref on interrupt
+    - staging: mt7621-pci: fix PCIE_FTS_NUM_LO macro
+    - HID: Add another Primax PIXART OEM mouse quirk
+    - lkdtm: support llvm-objcopy
+    - binder: fix memory leak in error path
+    - binder: return errors from buffer copy functions
+    - iio: adc: stm32-adc: add missing vdda-supply
+    - coresight: Potential uninitialized variable in probe()
+    - coresight: etb10: Do not call smp_processor_id from preemptible
+    - coresight: tmc-etr: Do not call smp_processor_id() from preemptible
+    - coresight: tmc-etr: alloc_perf_buf: Do not call smp_processor_id from
+      preemptible
+    - coresight: tmc-etf: Do not call smp_processor_id from preemptible
+    - carl9170: fix misuse of device driver API
+    - Revert "x86/build: Move _etext to actual end of .text"
+    - VMCI: Fix integer overflow in VMCI handle arrays
+    - staging: vchiq_2835_arm: revert "quit using custom down_interruptible()"
+    - staging: vchiq: make wait events interruptible
+    - staging: vchiq: revert "switch to wait_for_completion_killable"
+    - staging: fsl-dpaa2/ethsw: fix memory leak of switchdev_work
+    - staging: bcm2835-camera: Replace spinlock protecting context_map with mutex
+    - staging: bcm2835-camera: Ensure all buffers are returned on disable
+    - staging: bcm2835-camera: Remove check of the number of buffers supplied
+    - staging: bcm2835-camera: Handle empty EOS buffers whilst streaming
+    - staging: rtl8712: reduce stack usage, again
+    - Linux 5.2.1
+    - [Config] updateconfigs after v5.2.1 stable update
+
+  * fcf-protection=none patch with upstream version
+    - Revert "UBUNTU: SAUCE: add -fcf-protection=none to retpoline flags"
+    - SAUCE: kbuild: add -fcf-protection=none to retpoline flags
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests/ftrace: avoid failure when trying to probe a notrace
+      function
+    - SAUCE: selftests/powerpc/ptrace: fix build failure
+    - update dkms package versions
+    - [Packaging] add zlua to zfs-modules.ignore
+    - update dkms package versions
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 19 Jul 2019 15:04:45 -0500
+
+linux (5.2.0-8.9) eoan; urgency=medium
+
+  * linux: 5.2.0-8.9 -proposed tracker (LP: #1835700)
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] replace zfs and spl build with zfs 0.8.1-1ubuntu1
+    - SAUCE: test_bpf: remove expected fail for Ctx heavy transformations test on
+      s390
+    - SAUCE: add -fcf-protection=none to retpoline flags
+    - SAUCE: usbip: ensure strings copied using strncpy are null-terminated
+    - SAUCE: usbip: add -Wno-address-of-packed-member to EXTRA_CFLAGS
+    - SAUCE: perf jvmti: ensure strncpy result is null-terminated
+    - update dkms package versions
+    - add removed zfs modules to modules.ignore
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 08 Jul 2019 07:13:41 -0500
+
+linux (5.2.0-7.8) eoan; urgency=medium
+
+  * Kernel panic upon resetting ixgbe SR-IOV VFIO virtual function using 5.0
+    kernel (LP: #1829652)
+    - SAUCE: ixgbe: Avoid NULL pointer dereference with VF on non-IPsec hw
+
+  * Hi1620 driver updates from upstream 5.2 merge window (LP: #1830815)
+    - net: hns3: initialize CPU reverse mapping
+    - net: hns3: refine the flow director handle
+    - net: hns3: add aRFS support for PF
+    - net: hns3: fix for FEC configuration
+    - RDMA/hns: Remove unnecessary print message in aeq
+    - RDMA/hns: Update CQE specifications
+    - RDMA/hns: Move spin_lock_irqsave to the correct place
+    - RDMA/hns: Remove jiffies operation in disable interrupt context
+    - RDMA/hns: Replace magic numbers with #defines
+    - net: hns3: fix compile warning without CONFIG_RFS_ACCEL
+    - net: hns3: fix for HNS3_RXD_GRO_SIZE_M macro
+    - net: hns3: add support for dump firmware statistics by debugfs
+    - net: hns3: use HCLGE_STATE_NIC_REGISTERED to indicate PF NIC client has
+      registered
+    - net: hns3: use HCLGE_STATE_ROCE_REGISTERED to indicate PF ROCE client has
+      registered
+    - net: hns3: use HCLGEVF_STATE_NIC_REGISTERED to indicate VF NIC client has
+      registered
+    - net: hns3: modify hclge_init_client_instance()
+    - net: hns3: modify hclgevf_init_client_instance()
+    - net: hns3: add handshake with hardware while doing reset
+    - net: hns3: stop schedule reset service while unloading driver
+    - net: hns3: adjust hns3_uninit_phy()'s location in the hns3_client_uninit()
+    - net: hns3: fix a memory leak issue for hclge_map_unmap_ring_to_vf_vector
+    - RDMA/hns: Bugfix for posting multiple srq work request
+    - net: hns3: remove redundant core reset
+    - net: hns3: don't configure new VLAN ID into VF VLAN table when it's full
+    - net: hns3: fix VLAN filter restore issue after reset
+    - net: hns3: set the port shaper according to MAC speed
+    - net: hns3: add a check to pointer in error_detected and slot_reset
+    - net: hns3: set ops to null when unregister ad_dev
+    - net: hns3: add handling of two bits in MAC tunnel interrupts
+    - net: hns3: remove setting bit of reset_requests when handling mac tunnel
+      interrupts
+    - net: hns3: add opcode about query and clear RAS & MSI-X to special opcode
+    - net: hns3: delay and separate enabling of NIC and ROCE HW errors
+    - RDMA/hns: fix inverted logic of readl read and shift
+    - RDMA/hns: Bugfix for filling the sge of srq
+    - net: hns3: log detail error info of ROCEE ECC and AXI errors
+    - net: hns3: fix wrong size of mailbox responding data
+    - net: hns3: make HW GRO handling compliant with SW GRO
+    - net: hns3: replace numa_node_id with numa_mem_id for buffer reusing
+    - net: hns3: refactor hns3_get_new_int_gl function
+    - net: hns3: trigger VF reset if a VF has an over_8bd_nfe_err
+    - net: hns3: delete the redundant user NIC codes
+    - net: hns3: small changes for magic numbers
+    - net: hns3: use macros instead of magic numbers
+    - net: hns3: refactor PF/VF RSS hash key configuration
+    - net: hns3: some modifications to simplify and optimize code
+    - net: hns3: fix some coding style issues
+    - net: hns3: delay setting of reset level for hw errors until slot_reset is
+      called
+    - net: hns3: fix avoid unnecessary resetting for the H/W errors which do not
+      require reset
+    - net: hns3: process H/W errors occurred before HNS dev initialization
+    - net: hns3: add recovery for the H/W errors occurred before the HNS dev
+      initialization
+    - net: hns3: some changes of MSI-X bits in PPU(RCB)
+    - net: hns3: extract handling of mpf/pf msi-x errors into functions
+    - net: hns3: clear restting state when initializing HW device
+    - net: hns3: free irq when exit from abnormal branch
+    - net: hns3: fix for dereferencing before null checking
+    - net: hns3: fix for skb leak when doing selftest
+    - net: hns3: delay ring buffer clearing during reset
+    - net: hns3: some variable modification
+    - net: hns3: fix dereference of ae_dev before it is null checked
+    - scsi: hisi_sas: Delete PHY timers when rmmod or probe failed
+    - scsi: hisi_sas: Fix the issue of argument mismatch of printing ecc errors
+    - scsi: hisi_sas: Reduce HISI_SAS_SGE_PAGE_CNT in size
+    - scsi: hisi_sas: Change the type of some numbers to unsigned
+    - scsi: hisi_sas: Ignore the error code between phy down to phy up
+    - scsi: hisi_sas: Disable stash for v3 hw
+    - net: hns3: Add missing newline at end of file
+    - RDMa/hns: Don't stuck in endless timeout loop
+
+  * Sometimes touchpad automatically trigger double click (LP: #1833484)
+    - SAUCE: i2c: designware: Add disable runtime pm quirk
+
+  * Add pointstick support on HP ZBook 17 G5 (LP: #1833387)
+    - Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
+
+  * depmod may prefer unsigned l-r-m nvidia modules to signed modules
+    (LP: #1834479)
+    - [Packaging] dkms-build--nvidia-N -- clean up unsigned ko files
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests/powerpc: disable signal_fuzzer test
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 01 Jul 2019 07:22:18 -0500
+
+linux (5.2.0-6.7) eoan; urgency=medium
+
+  * hinic: fix oops due to race in set_rx_mode (LP: #1832048)
+    - hinic: fix a bug in set rx mode
+
+  * Miscellaneous Ubuntu changes
+    - rebase to v5.2-rc6
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 23 Jun 2019 23:36:11 -0500
+
+linux (5.2.0-5.6) eoan; urgency=medium
+
+  * QCA9377 isn't being recognized sometimes (LP: #1757218)
+    - SAUCE: USB: Disable USB2 LPM at shutdown
+
+  * shiftfs: allow changing ro/rw for subvolumes (LP: #1832316)
+    - SAUCE: shiftfs: allow changing ro/rw for subvolumes
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - [Packaging] replace nvidia-418 dkms build with nvidia-430
+    - SAUCE: import aufs driver
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 17 Jun 2019 15:04:12 -0500
+
+linux (5.2.0-4.5) eoan; urgency=medium
+
+  * arm64: cma_alloc errors at boot (LP: #1823753)
+    - [Config] Bump CMA_SIZE_MBYTES to 32 on arm64
+    - dma-contiguous: add dma_{alloc,free}_contiguous() helpers
+    - dma-contiguous: use fallback alloc_pages for single pages
+    - dma-contiguous: fix !CONFIG_DMA_CMA version of dma_{alloc,
+      free}_contiguous()
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_MFD_TQMX86=n for s390x
+    - [Config] CONFIG_GPIO_AMD_FCH=n for s390x
+    - [Config] CONFIG_BACKLIGHT_CLASS_DEVICE=n on s390x
+    - [Config] CONFIG_LCD_CLASS_DEVICE=n for s390x
+    - [Config] CONFIG_DRM_ETNAVIV=m for armhf generic-lpae
+    - [Config] CONFIG_DRM_NOUVEAU_SVM=n
+    - [Config] CONFIG_HWMON=n for s390x
+    - [Config] CONFIG_NEW_LEDS=n for s390x
+    - [Config] CONFIG_MTD_NAND_OMAP2=y for armhf
+    - [Config] CONFIG_VOP_BUS=n for non-amd64 arches
+    - [Config] CONFIG_TI_CPSW_PHY_SEL=n
+    - [Config] CONFIG_INTERCONNECT=n for s390x
+    - [Config] CONFIG_SCSI_GDTH=n for s390x
+    - [Config] CONFIG_PACKING=n for s390x
+    - [Config] CONFIG_ARCH_MILBEAUT=y for armhf
+    - [Config] update annotations following config review
+    - update dkms package versions
+    - [Config] enable nvidia dkms build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 10 Jun 2019 07:00:11 -0500
+
+linux (5.2.0-3.4) eoan; urgency=medium
+
+  * [18.04/18.10] File libperf-jvmti.so is missing in linux-tools-common deb on
+    Ubuntu (LP: #1761379)
+    - [Packaging] Support building libperf-jvmti.so
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "bpf, selftest: test global data/bss/rodata sections"
+    - update dkms package versions
+    - [Config] enable zfs
+    - rebase to v5.2-rc3
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 02 Jun 2019 21:48:50 -0500
+
+linux (5.2.0-2.3) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: perf arm64: Fix mksyscalltbl when system kernel headers are ahead of
+      the kernel
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 28 May 2019 07:12:39 -0500
+
+linux (5.2.0-1.2) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_INTEGRITY_PLATFORM_KEYRING=y
+    - update dkms package versions
+    - [Config] enable vbox dkms build
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 27 May 2019 21:11:27 -0500
+
+linux (5.2.0-0.1) eoan; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: import aufs driver
+    - [Packaging] disable ZFS
+    - [Packaging] disable nvidia
+    - [Packaging] dkms-build -- expand paths searched for make.log files
+    - add virtualbox-guest-dkms dkms package build
+    - enable vbox dkms build for amd64 and i386
+    - update dkms package versions
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) kexec_file: split KEXEC_VERIFY_SIG into KEXEC_SIG and
+      KEXEC_SIG_FORCE
+    - SAUCE: (efi-lockdown) kexec_file: Restrict at runtime if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Lock down module params that specify hardware
+      parameters (eg. ioport)
+    - SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the testmmiotrace module
+    - SAUCE: (efi-lockdown) Lock down /proc/kcore
+    - SAUCE: (efi-lockdown) Lock down kprobes
+    - SAUCE: (efi-lockdown) bpf: Restrict kernel image access functions when the
+      kernel is locked down
+    - SAUCE: (efi-lockdown) Lock down perf
+    - SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) lockdown: Print current->comm in restriction messages
+    - SAUCE: (efi-lockdown) kexec: Allow kexec_file() with appropriate IMA policy
+      when locked down
+    - SAUCE: (efi-lockdown) Make get_cert_list() not complain about cert lists
+      that aren't present.
+    - SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err().
+    - SAUCE: (efi-lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) KEYS: Make use of platform keyring for module
+      signature verify
+    - SAUCE: (efi-lockdown) debugfs: avoid EPERM when no open file operation
+      defined
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) furter KEXEC_VERIFY_SIG -> KEXEC_SIG updates
+    - SAUCE: (efi-lockdown) arm64: add kernel config option to lock down when in
+      Secure Boot mode
+    - update dkms package versions
+    - [Config] disable vbox build
+    - SAUCE: s390: mark __cpacf_check_opcode() and cpacf_query_func() as
+      __always_inline
+    - SAUCE: IB/mlx5: use size_t instead of u64 when dividing
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.2-rc1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 21 May 2019 11:18:43 -0500
+
+linux (5.2.0-0.0) eoan; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 21 May 2019 07:34:43 -0500
+
+linux (5.1.0-2.2) eoan; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+
+  * Eoan update: v5.1.2 upstream stable release (LP: #1829050)
+    - x86/msr-index: Cleanup bit defines
+    - x86/speculation: Consolidate CPU whitelists
+    - x86/speculation/mds: Add basic bug infrastructure for MDS
+    - x86/speculation/mds: Add BUG_MSBDS_ONLY
+    - x86/kvm: Expose X86_FEATURE_MD_CLEAR to guests
+    - x86/speculation/mds: Add mds_clear_cpu_buffers()
+    - x86/speculation/mds: Clear CPU buffers on exit to user
+    - x86/kvm/vmx: Add MDS protection when L1D Flush is not active
+    - x86/speculation/mds: Conditionally clear CPU buffers on idle entry
+    - x86/speculation/mds: Add mitigation control for MDS
+    - x86/speculation/mds: Add sysfs reporting for MDS
+    - x86/speculation/mds: Add mitigation mode VMWERV
+    - Documentation: Move L1TF to separate directory
+    - Documentation: Add MDS vulnerability documentation
+    - x86/speculation/mds: Add mds=full,nosmt cmdline option
+    - x86/speculation: Move arch_smt_update() call to after mitigation decisions
+    - x86/speculation/mds: Add SMT warning message
+    - x86/speculation/mds: Fix comment
+    - x86/speculation/mds: Print SMT vulnerable on MSBDS with mitigations off
+    - cpu/speculation: Add 'mitigations=' cmdline option
+    - x86/speculation: Support 'mitigations=' cmdline option
+    - powerpc/speculation: Support 'mitigations=' cmdline option
+    - s390/speculation: Support 'mitigations=' cmdline option
+    - x86/speculation/mds: Add 'mitigations=' support for MDS
+    - x86/mds: Add MDSUM variant to the MDS documentation
+    - Documentation: Correct the possible MDS sysfs values
+    - x86/speculation/mds: Fix documentation typo
+    - Linux 5.1.2
+
+  * Eoan update: v5.1.1 upstream stable release (LP: #1829046)
+    - Drivers: hv: vmbus: Remove the undesired put_cpu_ptr() in hv_synic_cleanup()
+    - ubsan: Fix nasty -Wbuiltin-declaration-mismatch GCC-9 warnings
+    - staging: greybus: power_supply: fix prop-descriptor request size
+    - staging: wilc1000: Avoid GFP_KERNEL allocation from atomic context.
+    - staging: most: cdev: fix chrdev_region leak in mod_exit
+    - staging: most: sound: pass correct device when creating a sound card
+    - usb: dwc3: Allow building USB_DWC3_QCOM without EXTCON
+    - usb: dwc3: Fix default lpm_nyet_threshold value
+    - USB: serial: f81232: fix interrupt worker not stop
+    - USB: cdc-acm: fix unthrottle races
+    - usb-storage: Set virt_boundary_mask to avoid SG overflows
+    - genirq: Prevent use-after-free and work list corruption
+    - intel_th: pci: Add Comet Lake support
+    - iio: adc: qcom-spmi-adc5: Fix of-based module autoloading
+    - cpufreq: armada-37xx: fix frequency calculation for opp
+    - ACPI / LPSS: Use acpi_lpss_* instead of acpi_subsys_* functions for
+      hibernate
+    - soc: sunxi: Fix missing dependency on REGMAP_MMIO
+    - scsi: lpfc: change snprintf to scnprintf for possible overflow
+    - scsi: qla2xxx: Fix incorrect region-size setting in optrom SYSFS routines
+    - scsi: qla2xxx: Set remote port devloss timeout to 0
+    - scsi: qla2xxx: Fix device staying in blocked state
+    - Bluetooth: hidp: fix buffer overflow
+    - Bluetooth: Align minimum encryption key size for LE and BR/EDR connections
+    - Bluetooth: Fix not initializing L2CAP tx_credits
+    - Bluetooth: hci_bcm: Fix empty regulator supplies for Intel Macs
+    - UAS: fix alignment of scatter/gather segments
+    - ASoC: Intel: avoid Oops if DMA setup fails
+    - i3c: Fix a shift wrap bug in i3c_bus_set_addr_slot_status()
+    - locking/futex: Allow low-level atomic operations to return -EAGAIN
+    - arm64: futex: Bound number of LDXR/STXR loops in FUTEX_WAKE_OP
+    - Linux 5.1.1
+
+  * shiftfs: lock security sensitive superblock flags (LP: #1827122)
+    - SAUCE: shiftfs: lock down certain superblock flags
+
+  * Please package libbpf (which is done out of the kernel src) in Debian [for
+    19.10] (LP: #1826410)
+    - SAUCE: tools -- fix add ability to disable libbfd
+
+  * ratelimit cma_alloc messages (LP: #1828092)
+    - SAUCE: cma: ratelimit cma_alloc error messages
+
+  * Headphone jack switch sense is inverted: plugging in headphones disables
+    headphone output (LP: #1824259)
+    - ASoC: rt5645: Headphone Jack sense inverts on the LattePanda board
+
+  * There are 4 HDMI/Displayport audio output listed in sound setting without
+    attach any HDMI/DP monitor (LP: #1827967)
+    - ALSA: hda/hdmi - Read the pin sense from register when repolling
+    - ALSA: hda/hdmi - Consider eld_valid when reporting jack event
+
+  * CONFIG_LOG_BUF_SHIFT set to 14 is too low on arm64 (LP: #1824864)
+    - [Config] CONFIG_LOG_BUF_SHIFT=18 on all 64bit arches
+
+  * CTAUTO:DevOps:860.50:devops4fp1:Error occurred during LINUX Dmesg error
+    Checking for all LINUX clients for devops4p10 (LP: #1766201)
+    - SAUCE: integrity: downgrade error to warning
+
+  * linux-buildinfo: pull out ABI information into its own package
+    (LP: #1806380)
+    - [Packaging] autoreconstruct -- base tag is always primary mainline version
+
+  * [SRU] Please sync vbox modules from virtualbox 6.0.6 on next kernel update
+    (LP: #1825210)
+    - vbox-update: updates for renamed makefiles
+    - ubuntu: vbox -- update to 6.0.6-dfsg-1
+
+  * autofs kernel module missing (LP: #1824333)
+    - [Config] Update autofs4 path in inclusion list
+
+  * The Realtek card reader does not enter PCIe 1.1/1.2 (LP: #1825487)
+    - SAUCE: misc: rtsx: Fixed rts5260 power saving parameter and sd glitch
+
+  * CVE-2019-3874
+    - sctp: implement memory accounting on tx path
+    - sctp: implement memory accounting on rx path
+
+  * apparmor does not start in Disco LXD containers (LP: #1824812)
+    - SAUCE: shiftfs: use separate llseek method for directories
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] autoreconstruct -- remove for -rc kernels
+    - SAUCE: (efi-lockdown) debugfs: avoid EPERM when no open file operation
+      defined
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) furter KEXEC_VERIFY_SIG -> KEXEC_SIG updates
+    - [Config] (efi-lockdown): update configs after efi lockdown patch refresh
+    - [Packaging] don't delete efi_parser.c
+    - vbox-update -- do not fix up KERN_DIR or KBUILD_EXTMOD
+    - ubuntu: vbox -- update to 6.0.6-dfsg-2
+    - add nvidia-418 dkms build
+    - remove virtualbox guest drivers
+    - [Packaging] dkms-build -- expand paths searched for make.log files
+    - add virtualbox-guest-dkms dkms package build
+    - enable vbox dkms build for amd64 and i386
+    - [Config] update configs for v5.1(-rc7)? rebase
+    - update dkms package versions
+    - Add the ability to lock down access to the running kernel image
+    - Enforce module signatures if the kernel is locked down
+    - Restrict /dev/{mem,kmem,port} when the kernel is locked down
+    - kexec_load: Disable at runtime if the kernel is locked down
+    - Copy secure_boot flag in boot params across kexec reboot
+    - kexec_file: split KEXEC_VERIFY_SIG into KEXEC_SIG and KEXEC_SIG_FORCE
+    - kexec_file: Restrict at runtime if the kernel is locked down
+    - hibernate: Disable when the kernel is locked down
+    - uswsusp: Disable when the kernel is locked down
+    - PCI: Lock down BAR access when the kernel is locked down
+    - x86: Lock down IO port access when the kernel is locked down
+    - x86/msr: Restrict MSR access when the kernel is locked down
+    - ACPI: Limit access to custom_method when the kernel is locked down
+    - acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
+    - acpi: Disable ACPI table override if the kernel is locked down
+    - acpi: Disable APEI error injection if the kernel is locked down
+    - Prohibit PCMCIA CIS storage when the kernel is locked down
+    - Lock down TIOCSSERIAL
+    - Lock down module params that specify hardware parameters (eg. ioport)
+    - x86/mmiotrace: Lock down the testmmiotrace module
+    - Lock down /proc/kcore
+    - Lock down kprobes
+    - bpf: Restrict kernel image access functions when the kernel is locked down
+    - Lock down perf
+    - debugfs: Restrict debugfs when the kernel is locked down
+    - lockdown: Print current->comm in restriction messages
+    - kexec: Allow kexec_file() with appropriate IMA policy when locked down
+    - Make get_cert_list() not complain about cert lists that aren't present.
+    - Add efi_status_to_str() and rework efi_status_to_err().
+    - Make get_cert_list() use efi_status_to_str() to print error messages.
+    - efi: Add an EFI_SECURE_BOOT flag to indicate secure boot mode
+    - efi: Lock down the kernel if booted in secure boot mode
+    - KEYS: Make use of platform keyring for module signature verify
+
+  * Miscellaneous upstream changes
+    - ALSA: hdea/realtek - Headset fixup for System76 Gazelle (gaze14)
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 14 May 2019 12:32:56 -0500
+
+linux (5.1.0-1.1) eoan; urgency=medium
+
+  * bionic: fork out linux-snapdragon into its own topic kernel (LP: #1820868)
+    - [Packaging]: really drop snapdragon
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: fix vbox use of MAP_SHARED
+    - SAUCE: fix vbox use of vm_fault_t
+    - [Packaging] disable ZFS
+    - [Packaging] disable nvidia
+    - SAUCE: perf annotate: Fix build on 32 bit for BPF annotation
+    - [Config]: updateconfig after rebase to v5.1-rc
+    - [Config]: build ETNAVIV only on arm platforms
+    - [Config]: Disable CMA on non-arm platforms
+    - [Config]: MMC_CQHCI is needed by some built-in drivers
+    - [Config]: a.out support has been deprecated
+    - [Config]: R3964 was marked as BROKEN
+    - [Config]: Add SENSIRION_SGP30 module
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: tools: lib/bpf -- add generated headers to search
+      path"
+    - Revert "UBUNTU: SAUCE: btqcomsmd: introduce BT_QCOMSMD_HACK"
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Thu, 25 Apr 2019 10:03:25 -0300
+
+linux (5.1.0-0.0) eoan; urgency=medium
+
+  * Dummy entry.
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Thu, 25 Apr 2019 09:49:47 -0300
+
+linux (5.0.0-13.14) disco; urgency=medium
+
+  * linux: 5.0.0-13.14 -proposed tracker (LP: #1824819)
+
+  * Display only has 640x480 (LP: #1824677)
+    - Revert "UBUNTU: SAUCE: drm/nouveau: Disable nouveau driver by default"
+
+  * shiftfs: use after free when checking mount options (LP: #1824735)
+    - SAUCE: shiftfs: prevent use-after-free when verifying mount options
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 15 Apr 2019 09:11:23 -0500
+
+linux (5.0.0-12.13) disco; urgency=medium
+
+  * linux: 5.0.0-12.13 -proposed tracker (LP: #1824726)
+
+  * Linux 5.0 black screen on boot, display flickers (i915 regression with
+    certain laptop panels) (LP: #1824216)
+    - drm/i915/dp: revert back to max link rate and lane count on eDP
+
+  * kernel BUG at fs/attr.c:287 when using shiftfs (LP: #1824717)
+    - SAUCE: shiftfs: fix passing of attrs to underaly for setattr
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 14 Apr 2019 13:38:05 -0500
+
+linux (5.0.0-11.12) disco; urgency=medium
+
+  * linux: 5.0.0-11.12 -proposed tracker (LP: #1824383)
+
+  * hns3: PPU_PF_ABNORMAL_INT_ST over_8bd_no_fe found [error status=0x1]
+    (LP: #1824194)
+    - net: hns3: fix for not calculating tx bd num correctly
+
+  * disco: unable to use iptables/enable ufw under -virtual kernel
+    (LP: #1823862)
+    - [Packaging] add bpfilter to linux-modules
+
+  * Make shiftfs a module rather than built-in (LP: #1824354)
+    - [Config] CONFIG_SHIFT_FS=m
+
+  * shiftfs: chown sets untranslated ids in lower fs (LP: #1824350)
+    - SAUCE: shiftfs: use translated ids when chaning lower fs attrs
+
+  * [Hyper-V] KVP daemon fails to start on first boot of disco VM (LP: #1820063)
+    - [Packaging] bind hv_kvp_daemon startup to hv_kvp device
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 11 Apr 2019 10:17:19 -0500
+
+linux (5.0.0-10.11) disco; urgency=medium
+
+  * linux: 5.0.0-10.11 -proposed tracker (LP: #1823936)
+
+  * Apparmor enforcement failure in lxc selftests (LP: #1823379)
+    - SAUCE: apparmor: Restore Y/N in /sys for apparmor's "enabled"
+
+  * systemd cause kernel trace "BUG: unable to handle kernel paging request at
+    6db23a14" on Cosmic i386 (LP: #1813244)
+    - openvswitch: fix flow actions reallocation
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 09 Apr 2019 08:30:38 -0500
+
+linux (5.0.0-9.10) disco; urgency=medium
+
+  * linux: 5.0.0-9.10 -proposed tracker (LP: #1823228)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] update helper scripts
+    - [Packaging] resync retpoline extraction
+
+  * Huawei Hi1822 NIC has poor performance (LP: #1820187)
+    - net-next/hinic: replace disable_irq_nosync/enable_irq
+
+  * Add uid shifting overlay filesystem (shiftfs) (LP: #1823186)
+    - shiftfs: uid/gid shifting bind mount
+    - shiftfs: rework and extend
+    - shiftfs: support some btrfs ioctls
+    - [Config] enable shiftfs
+
+  * Cannot boot or install - have to use nomodeset (LP: #1821820)
+    - Revert "drm/i915/fbdev: Actually configure untiled displays"
+
+  * Disco update: v5.0.6 upstream stable release (LP: #1823060)
+    - netfilter: nf_tables: fix set double-free in abort path
+    - dccp: do not use ipv6 header for ipv4 flow
+    - genetlink: Fix a memory leak on error path
+    - gtp: change NET_UDP_TUNNEL dependency to select
+    - ipv6: make ip6_create_rt_rcu return ip6_null_entry instead of NULL
+    - mac8390: Fix mmio access size probe
+    - mISDN: hfcpci: Test both vendor & device ID for Digium HFC4S
+    - net: aquantia: fix rx checksum offload for UDP/TCP over IPv6
+    - net: datagram: fix unbounded loop in __skb_try_recv_datagram()
+    - net/packet: Set __GFP_NOWARN upon allocation in alloc_pg_vec
+    - net: phy: meson-gxl: fix interrupt support
+    - net: rose: fix a possible stack overflow
+    - net: stmmac: fix memory corruption with large MTUs
+    - net-sysfs: call dev_hold if kobject_init_and_add success
+    - net: usb: aqc111: Extend HWID table by QNAP device
+    - packets: Always register packet sk in the same order
+    - rhashtable: Still do rehash when we get EEXIST
+    - sctp: get sctphdr by offset in sctp_compute_cksum
+    - sctp: use memdup_user instead of vmemdup_user
+    - tcp: do not use ipv6 header for ipv4 flow
+    - tipc: allow service ranges to be connect()'ed on RDM/DGRAM
+    - tipc: change to check tipc_own_id to return in tipc_net_stop
+    - tipc: fix cancellation of topology subscriptions
+    - tun: properly test for IFF_UP
+    - vrf: prevent adding upper devices
+    - vxlan: Don't call gro_cells_destroy() before device is unregistered
+    - thunderx: enable page recycling for non-XDP case
+    - thunderx: eliminate extra calls to put_page() for pages held for recycling
+    - net: dsa: mv88e6xxx: fix few issues in mv88e6390x_port_set_cmode
+    - net: mii: Fix PAUSE cap advertisement from linkmode_adv_to_lcl_adv_t()
+      helper
+    - net: phy: don't clear BMCR in genphy_soft_reset
+    - r8169: fix cable re-plugging issue
+    - ila: Fix rhashtable walker list corruption
+    - tun: add a missing rcu_read_unlock() in error path
+    - powerpc/fsl: Fix the flush of branch predictor.
+    - Btrfs: fix incorrect file size after shrinking truncate and fsync
+    - btrfs: remove WARN_ON in log_dir_items
+    - btrfs: don't report readahead errors and don't update statistics
+    - btrfs: Fix bound checking in qgroup_trace_new_subtree_blocks
+    - btrfs: Avoid possible qgroup_rsv_size overflow in
+      btrfs_calculate_inode_block_rsv_size
+    - Btrfs: fix assertion failure on fsync with NO_HOLES enabled
+    - locks: wake any locks blocked on request before deadlock check
+    - tracing: initialize variable in create_dyn_event()
+    - ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time
+    - powerpc: bpf: Fix generation of load/store DW instructions
+    - vfio: ccw: only free cp on final interrupt
+    - NFS: Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
+    - NFS: fix mount/umount race in nlmclnt.
+    - NFSv4.1 don't free interrupted slot on open
+    - net: dsa: qca8k: remove leftover phy accessors
+    - ALSA: rawmidi: Fix potential Spectre v1 vulnerability
+    - ALSA: seq: oss: Fix Spectre v1 vulnerability
+    - ALSA: pcm: Fix possible OOB access in PCM oss plugins
+    - ALSA: pcm: Don't suspend stream in unrecoverable PCM state
+    - ALSA: hda/realtek - Fixed Headset Mic JD not stable
+    - ALSA: hda/realtek: merge alc_fixup_headset_jack to alc295_fixup_chromebook
+    - ALSA: hda/realtek - Add support headset mode for DELL WYSE AIO
+    - ALSA: hda/realtek - Add support headset mode for New DELL WYSE NB
+    - ALSA: hda/realtek: Enable headset MIC of Acer AIO with ALC286
+    - ALSA: hda/realtek: Enable headset MIC of Acer Aspire Z24-890 with ALC286
+    - ALSA: hda/realtek - Add support for Acer Aspire E5-523G/ES1-432 headset mic
+    - ALSA: hda/realtek: Enable ASUS X441MB and X705FD headset MIC with ALC256
+    - ALSA: hda/realtek: Enable headset mic of ASUS P5440FF with ALC256
+    - ALSA: hda/realtek: Enable headset MIC of ASUS X430UN and X512DK with ALC256
+    - ALSA: hda/realtek - Fix speakers on Acer Predator Helios 500 Ryzen laptops
+    - kbuild: modversions: Fix relative CRC byte order interpretation
+    - fs/open.c: allow opening only regular files during execve()
+    - ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
+    - scsi: sd: Fix a race between closing an sd device and sd I/O
+    - scsi: sd: Quiesce warning if device does not report optimal I/O size
+    - scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
+    - scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP
+      devices
+    - drm/rockchip: vop: reset scale mode when win is disabled
+    - tty/serial: atmel: Add is_half_duplex helper
+    - tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
+    - tty: mxs-auart: fix a potential NULL pointer dereference
+    - tty: atmel_serial: fix a potential NULL pointer dereference
+    - tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
+    - staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
+    - staging: olpc_dcon_xo_1: add missing 'const' qualifier
+    - staging: speakup_soft: Fix alternate speech with other synths
+    - staging: vt6655: Remove vif check from vnt_interrupt
+    - staging: vt6655: Fix interrupt race condition on device start up.
+    - staging: erofs: fix to handle error path of erofs_vmap()
+    - staging: erofs: fix error handling when failed to read compresssed data
+    - staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
+    - serial: max310x: Fix to avoid potential NULL pointer dereference
+    - serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference
+    - serial: sh-sci: Fix setting SCSCR_TIE while transferring data
+    - USB: serial: cp210x: add new device id
+    - USB: serial: ftdi_sio: add additional NovaTech products
+    - USB: serial: mos7720: fix mos_parport refcount imbalance on error path
+    - USB: serial: option: set driver_info for SIM5218 and compatibles
+    - USB: serial: option: add support for Quectel EM12
+    - USB: serial: option: add Olicard 600
+    - ACPI / CPPC: Fix guaranteed performance handling
+    - Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
+    - fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
+    - drivers/block/zram/zram_drv.c: fix idle/writeback string compare
+    - blk-mq: fix sbitmap ws_active for shared tags
+    - cpufreq: intel_pstate: Also use CPPC nominal_perf for base_frequency
+    - cpufreq: scpi: Fix use after free
+    - drm/vgem: fix use-after-free when drm_gem_handle_create() fails
+    - drm/vkms: fix use-after-free when drm_gem_handle_create() fails
+    - drm/i915: Mark AML 0x87CA as ULX
+    - drm/i915/gvt: Fix MI_FLUSH_DW parsing with correct index check
+    - drm/i915/icl: Fix the TRANS_DDI_FUNC_CTL2 bitfield macro
+    - gpio: exar: add a check for the return value of ida_simple_get fails
+    - gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
+    - phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
+    - usb: mtu3: fix EXTCON dependency
+    - USB: gadget: f_hid: fix deadlock in f_hidg_write()
+    - usb: common: Consider only available nodes for dr_mode
+    - mm/memory.c: fix modifying of page protection by insert_pfn()
+    - usb: host: xhci-rcar: Add XHCI_TRUST_TX_LENGTH quirk
+    - xhci: Fix port resume done detection for SS ports with LPM enabled
+    - usb: xhci: dbc: Don't free all memory with spinlock held
+    - xhci: Don't let USB3 ports stuck in polling state prevent suspend
+    - usb: cdc-acm: fix race during wakeup blocking TX traffic
+    - usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
+    - usb: typec: Fix unchecked return value
+    - mm/hotplug: fix offline undo_isolate_page_range()
+    - mm: add support for kmem caches in DMA32 zone
+    - iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
+    - mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
+    - mm/debug.c: fix __dump_page when mapping->host is not set
+    - mm/memory_hotplug.c: fix notification in offline error path
+    - mm/page_isolation.c: fix a wrong flag in set_migratetype_isolate()
+    - mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
+    - perf pmu: Fix parser error for uncore event alias
+    - perf intel-pt: Fix TSC slip
+    - objtool: Query pkg-config for libelf location
+    - powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
+    - powerpc/64: Fix memcmp reading past the end of src/dest
+    - powerpc/pseries/mce: Fix misleading print for TLB mutlihit
+    - watchdog: Respect watchdog cpumask on CPU hotplug
+    - cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n
+    - x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
+    - KVM: Reject device ioctls from processes other than the VM's creator
+    - KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
+    - KVM: x86: update %rip after emulating IO
+    - bpf: do not restore dst_reg when cur_state is freed
+    - mt76x02u: use usb_bulk_msg to upload firmware
+    - Linux 5.0.6
+
+  * RDMA/hns updates for disco (LP: #1822897)
+    - RDMA/hns: Fix the bug with updating rq head pointer when flush cqe
+    - RDMA/hns: Bugfix for the scene without receiver queue
+    - RDMA/hns: Add constraint on the setting of local ACK timeout
+    - RDMA/hns: Modify the pbl ba page size for hip08
+    - RDMA/hns: RDMA/hns: Assign rq head pointer when enable rq record db
+    - RDMA/hns: Add the process of AEQ overflow for hip08
+    - RDMA/hns: Add SCC context allocation support for hip08
+    - RDMA/hns: Add SCC context clr support for hip08
+    - RDMA/hns: Add timer allocation support for hip08
+    - RDMA/hns: Remove set but not used variable 'rst'
+    - RDMA/hns: Make some function static
+    - RDMA/hns: Fix the Oops during rmmod or insmod ko when reset occurs
+    - RDMA/hns: Fix the chip hanging caused by sending mailbox&CMQ during reset
+    - RDMA/hns: Fix the chip hanging caused by sending doorbell during reset
+    - RDMA/hns: Limit minimum ROCE CQ depth to 64
+    - RDMA/hns: Fix the state of rereg mr
+    - RDMA/hns: Set allocated memory to zero for wrid
+    - RDMA/hns: Delete useful prints for aeq subtype event
+    - RDMA/hns: Configure capacity of hns device
+    - RDMA/hns: Modify qp&cq&pd specification according to UM
+    - RDMA/hns: Bugfix for set hem of SCC
+    - RDMA/hns: Use GFP_ATOMIC in hns_roce_v2_modify_qp
+
+  * autopkgtests run too often, too much and don't skip enough (LP: #1823056)
+    - Set +x on rebuild testcase.
+    - Skip rebuild test, for regression-suite deps.
+    - Make ubuntu-regression-suite skippable on unbootable kernels.
+    - make rebuild use skippable error codes when skipping.
+    - Only run regression-suite, if requested to.
+
+  * touchpad not working on lenovo yoga 530 (LP: #1787775)
+    - Revert "UBUNTU: SAUCE: i2c:amd Depends on ACPI"
+    - Revert "UBUNTU: SAUCE: i2c:amd move out pointer in union i2c_event_base"
+    - i2c: add extra check to safe DMA buffer helper
+    - i2c: Add drivers for the AMD PCIe MP2 I2C controller
+    - [Config] Update config for AMD MP2 I2C driver
+
+  * Detect SMP PHY control command errors (LP: #1822680)
+    - scsi: libsas: Check SMP PHY control function result
+
+  * disable a.out support (LP: #1818552)
+    - [Config] Disable a.out support
+    - [Config] remove binfmt_aout from abi for i386 lowlatency
+
+  * bionic: fork out linux-snapdragon into its own topic kernel (LP: #1820868)
+    - [Packaging] remove snapdragon flavour support
+    - Revert "UBUNTU: SAUCE: (snapdragon) drm/msm/adv7511: wrap hacks under
+      CONFIG_ADV7511_SNAPDRAGON_HACKS #ifdefs"
+    - Revert "UBUNTU: SAUCE: (snapdragon) media: ov5645: skip address change if dt
+      addr == default addr"
+    - Revert "UBUNTU: SAUCE: (snapdragon) DT: leds: Add Qualcomm Light Pulse
+      Generator binding"
+    - Revert "UBUNTU: SAUCE: (snapdragon) MAINTAINERS: Add Qualcomm Camera Control
+      Interface driver"
+    - Revert "UBUNTU: SAUCE: (snapdragon) dt-bindings: media: Binding document for
+      Qualcomm Camera Control Interface driver"
+    - Revert "UBUNTU: SAUCE: (snapdragon) leds: Add driver for Qualcomm LPG"
+    - Revert "UBUNTU: SAUCE: (snapdragon) HACK: drm/msm/adv7511: Don't rely on
+      interrupts for EDID parsing"
+    - Revert "UBUNTU: SAUCE: (snapdragon) drm/bridge/adv7511: Delay clearing of
+      HPD interrupt status"
+    - Revert "UBUNTU: SAUCE: (snapdragon) media: ov5645: Fix I2C address"
+    - Revert "UBUNTU: SAUCE: (snapdragon) i2c-qcom-cci: Fix I2C address bug"
+    - Revert "UBUNTU: SAUCE: (snapdragon) i2c-qcom-cci: Fix run queue completion
+      timeout"
+    - Revert "UBUNTU: SAUCE: (snapdragon) camss: Do not register if no cameras are
+      present"
+    - Revert "UBUNTU: SAUCE: (snapdragon) i2c: Add Qualcomm Camera Control
+      Interface driver"
+    - Revert "UBUNTU: SAUCE: (snapdragon) ov5645: I2C address change"
+    - Revert "UBUNTU: SAUCE: (snapdragon) regulator: smd: Allow
+      REGULATOR_QCOM_SMD_RPM=m"
+    - Revert "UBUNTU: SAUCE: (snapdragon) cpufreq: Add apq8016 to cpufreq-dt-
+      platdev blacklist"
+    - Revert "UBUNTU: SAUCE: (snapdragon) PM / OPP: Add a helper to get an opp
+      regulator for device"
+    - Revert "UBUNTU: SAUCE: (snapdragon) PM / OPP: HACK: Allow to set regulator
+      without opp_list"
+    - Revert "UBUNTU: SAUCE: (snapdragon) PM / OPP: Drop RCU usage in
+      dev_pm_opp_adjust_voltage()"
+    - Revert "UBUNTU: SAUCE: (snapdragon) PM / OPP: Support adjusting OPP voltages
+      at runtime"
+    - Revert "UBUNTU: SAUCE: (snapdragon) regulator: smd: Add floor and corner
+      operations"
+    - Revert "UBUNTU: SAUCE: (snapdragon) power: avs: cpr: Register with cpufreq-
+      dt"
+    - Revert "UBUNTU: SAUCE: (snapdragon) power: avs: cpr: fix with new
+      reg_sequence structures"
+    - Revert "UBUNTU: SAUCE: (snapdragon) power: avs: cpr: Use raw mem access for
+      qfprom"
+    - Revert "UBUNTU: SAUCE: (snapdragon) power: avs: Add support for CPR (Core
+      Power Reduction)"
+    - Revert "UBUNTU: SAUCE: (snapdragon) HACK: drm/msm/iommu: Remove runtime_put
+      calls in map/unmap"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: enable LEDS_QCOM_LPG"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: distro.config: enable 'BBR' TCP
+      congestion algorithm"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: distro.config: enable 'fq' and
+      'fq_codel' qdiscs"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: distro.config: enable
+      'schedutil' CPUfreq governor"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: configs: set USB_CONFIG_F_FS in
+      distro.config"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: enable
+      CONFIG_USB_CONFIGFS_F_FS by default"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: configs: add freq stat to sysfs"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: configs: Enable camera drivers"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: disable ANALOG_TV and
+      DIGITAL_TV"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: configs: add more USB net
+      drivers"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: configs: enable BT_QCOMSMD"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: enable
+      CFG80211_DEFAULT_PS by default"
+    - Revert "UBUNTU: SAUCE: (snapdragon) Force the SMD regulator driver to be
+      compiled-in"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: configs: enable dm_mod and
+      dm_crypt"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: Enable a53/apcs and
+      avs"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: configs: enable QCOM Venus"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: distro.config: enable debug
+      friendly USB network adpater"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: configs: enable WCN36xx"
+    - Revert "UBUNTU: SAUCE: (snapdragon) kernel: configs; add distro.config"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: enable QCOM audio
+      drivers for APQ8016 and DB410c"
+    - Revert "UBUNTU: SAUCE: (snapdragon) arm64: defconfig: enable REMOTEPROC"
+    - [Config] fix abi for remove i2c-qcom-cci module
+    - [Config] update annotations
+    - [Config] update configs following snapdragon removal
+
+  * Disco update: v5.0.5 upstream stable release (LP: #1822671)
+    - Revert "ALSA: hda - Enforces runtime_resume after S3 and S4 for each codec"
+    - ALSA: hda - add Lenovo IdeaCentre B550 to the power_save_blacklist
+    - ALSA: firewire-motu: use 'version' field of unit directory to identify model
+    - mmc: pxamci: fix enum type confusion
+    - mmc: alcor: fix DMA reads
+    - mmc: mxcmmc: "Revert mmc: mxcmmc: handle highmem pages"
+    - mmc: renesas_sdhi: limit block count to 16 bit for old revisions
+    - drm/amdgpu: fix invalid use of change_bit
+    - drm/vmwgfx: Don't double-free the mode stored in par->set_mode
+    - drm/vmwgfx: Return 0 when gmrid::get_node runs out of ID's
+    - iommu/amd: fix sg->dma_address for sg->offset bigger than PAGE_SIZE
+    - iommu/iova: Fix tracking of recently failed iova address
+    - libceph: wait for latest osdmap in ceph_monc_blacklist_add()
+    - udf: Fix crash on IO error during truncate
+    - mips: loongson64: lemote-2f: Add IRQF_NO_SUSPEND to "cascade" irqaction.
+    - MIPS: Ensure ELF appended dtb is relocated
+    - MIPS: Fix kernel crash for R6 in jump label branch function
+    - powerpc/vdso64: Fix CLOCK_MONOTONIC inconsistencies across Y2038
+    - powerpc/security: Fix spectre_v2 reporting
+    - net/mlx5: Fix DCT creation bad flow
+    - scsi: core: Avoid that a kernel warning appears during system resume
+    - scsi: qla2xxx: Fix FC-AL connection target discovery
+    - scsi: ibmvscsi: Protect ibmvscsi_head from concurrent modificaiton
+    - scsi: ibmvscsi: Fix empty event pool access during host removal
+    - futex: Ensure that futex address is aligned in handle_futex_death()
+    - perf probe: Fix getting the kernel map
+    - objtool: Move objtool_file struct off the stack
+    - irqchip/gic-v3-its: Fix comparison logic in lpi_range_cmp
+    - clocksource/drivers/riscv: Fix clocksource mask
+    - ALSA: ac97: Fix of-node refcount unbalance
+    - ext4: fix NULL pointer dereference while journal is aborted
+    - ext4: fix data corruption caused by unaligned direct AIO
+    - ext4: brelse all indirect buffer in ext4_ind_remove_space()
+    - media: v4l2-ctrls.c/uvc: zero v4l2_event
+    - Bluetooth: hci_uart: Check if socket buffer is ERR_PTR in h4_recv_buf()
+    - Bluetooth: Fix decrementing reference count twice in releasing socket
+    - Bluetooth: hci_ldisc: Initialize hci_dev before open()
+    - Bluetooth: hci_ldisc: Postpone HCI_UART_PROTO_READY bit set in
+      hci_uart_set_proto()
+    - drm/vkms: Fix flush_work() without INIT_WORK().
+    - RDMA/cma: Rollback source IP address if failing to acquire device
+    - f2fs: fix to avoid deadlock of atomic file operations
+    - aio: simplify - and fix - fget/fput for io_submit()
+    - netfilter: ebtables: remove BUGPRINT messages
+    - loop: access lo_backing_file only when the loop device is Lo_bound
+    - x86/unwind: Handle NULL pointer calls better in frame unwinder
+    - x86/unwind: Add hardcoded ORC entry for NULL
+    - locking/lockdep: Add debug_locks check in __lock_downgrade()
+    - ALSA: hda - Record the current power state before suspend/resume calls
+    - ALSA: hda - Enforces runtime_resume after S3 and S4 for each codec
+    - Linux 5.0.5
+
+  * hisi_sas updates for disco (LP: #1822385)
+    - scsi: hisi_sas: send primitive NOTIFY to SSP situation only
+    - scsi: hisi_sas: shutdown axi bus to avoid exception CQ returned
+    - scsi: hisi_sas: remove the check of sas_dev status in
+      hisi_sas_I_T_nexus_reset()
+    - scsi: hisi_sas: Remove unused parameter of function hisi_sas_alloc()
+    - scsi: hisi_sas: Reject setting programmed minimum linkrate > 1.5G
+    - scsi: hisi_sas: Fix losing directly attached disk when hot-plug
+    - scsi: hisi_sas: Correct memory allocation size for DQ debugfs
+    - scsi: hisi_sas: Some misc tidy-up
+    - scsi: hisi_sas: Fix to only call scsi_get_prot_op() for non-NULL scsi_cmnd
+    - scsi: hisi_sas: Add missing seq_printf() call in hisi_sas_show_row_32()
+    - scsi: hisi_sas: Add support for DIX feature for v3 hw
+    - scsi: hisi_sas: Add manual trigger for debugfs dump
+    - scsi: hisi_sas: change queue depth from 512 to 4096
+    - scsi: hisi_sas: Issue internal abort on all relevant queues
+    - scsi: hisi_sas: Use pci_irq_get_affinity() for v3 hw as experimental
+    - scsi: hisi_sas: Do some more tidy-up
+    - scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
+    - scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
+    - scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
+    - scsi: hisi_sas: Set PHY linkrate when disconnected
+    - scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP
+      target port
+    - scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of
+      HiLink
+    - scsi: hisi_sas: Add softreset in hisi_sas_I_T_nexus_reset()
+
+  * [Patch][Raven 2] kernel 5.0.0 cannot boot because of psp response
+    (LP: #1822267)
+    - drm/amdgpu/psp: Fix can't detect psp INVOKE command failed
+    - drm/amdgpu/psp: ignore psp response status
+
+  * 3b080b2564287be91605bfd1d5ee985696e61d3c in ubuntu_btrfs_kernel_fixes
+    triggers system hang on i386 (LP: #1812845)
+    - btrfs: raid56: properly unmap parity page in finish_parity_scrub()
+
+  * enable CONFIG_DRM_BOCHS (LP: #1795857)
+    - [Config] Reenable DRM_BOCHS as module
+
+  * [Dell Precision 7530/5530 with Nvidia Quadro P1000] Live USB freezes or
+    cannot complete install when nouveau driver is loaded (crashing in GP100
+    code) (LP: #1822026)
+    - SAUCE: drm/nouveau: Disable nouveau driver by default
+
+  * Need to add Intel CML related pci-id's (LP: #1821863)
+    - drm/i915/cml: Add CML PCI IDS
+    - drm/i915/cml: Introduce Comet Lake PCH
+
+  * ARM: Add support for the SDEI interface (LP: #1822005)
+    - ACPI / APEI: Don't wait to serialise with oops messages when panic()ing
+    - ACPI / APEI: Remove silent flag from ghes_read_estatus()
+    - ACPI / APEI: Switch estatus pool to use vmalloc memory
+    - ACPI / APEI: Make hest.c manage the estatus memory pool
+    - ACPI / APEI: Make estatus pool allocation a static size
+    - ACPI / APEI: Don't store CPER records physical address in struct ghes
+    - ACPI / APEI: Remove spurious GHES_TO_CLEAR check
+    - ACPI / APEI: Don't update struct ghes' flags in read/clear estatus
+    - ACPI / APEI: Generalise the estatus queue's notify code
+    - ACPI / APEI: Don't allow ghes_ack_error() to mask earlier errors
+    - ACPI / APEI: Move NOTIFY_SEA between the estatus-queue and NOTIFY_NMI
+    - ACPI / APEI: Switch NOTIFY_SEA to use the estatus queue
+    - KVM: arm/arm64: Add kvm_ras.h to collect kvm specific RAS plumbing
+    - arm64: KVM/mm: Move SEA handling behind a single 'claim' interface
+    - ACPI / APEI: Move locking to the notification helper
+    - ACPI / APEI: Let the notification helper specify the fixmap slot
+    - ACPI / APEI: Pass ghes and estatus separately to avoid a later copy
+    - ACPI / APEI: Make GHES estatus header validation more user friendly
+    - ACPI / APEI: Split ghes_read_estatus() to allow a peek at the CPER length
+    - ACPI / APEI: Only use queued estatus entry during in_nmi_queue_one_entry()
+    - ACPI / APEI: Use separate fixmap pages for arm64 NMI-like notifications
+    - firmware: arm_sdei: Add ACPI GHES registration helper
+    - ACPI / APEI: Add support for the SDEI GHES Notification type
+
+  * CVE-2019-9857
+    - inotify: Fix fsnotify_mark refcount leak in inotify_update_existing_watch()
+
+  * scsi: libsas: Support SATA PHY connection rate unmatch fixing during
+    discovery (LP: #1821408)
+    - scsi: libsas: Support SATA PHY connection rate unmatch fixing during
+      discovery
+
+  * Qualcomm Atheros QCA9377 wireless does not work (LP: #1818204)
+    - platform/x86: ideapad-laptop: Add Ideapad 530S-14ARR to no_hw_rfkill list
+
+  * Lenovo ideapad 330-15ICH Wifi rfkill hard blocked (LP: #1811815)
+    - platform/x86: ideapad: Add ideapad 330-15ICH to no_hw_rfkill
+
+  * hid-sensor-hub spamming dmesg in 4.20 (LP: #1818547)
+    - HID: Increase maximum report size allowed by hid_field_extract()
+
+  * [disco] [5.0.0-7.8] can't mount guest cifs share (LP: #1821053)
+    - cifs: allow guest mounts to work for smb3.11
+    - SMB3: Fix SMB3.1.1 guest mounts to Samba
+
+  * Add HiSilicon SoC quirk for cpufreq (LP: #1821620)
+    - ACPI / CPPC: Add a helper to get desired performance
+    - cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
+
+  * Disco update: v5.0.4 upstream stable release (LP: #1821607)
+    - 9p: use inode->i_lock to protect i_size_write() under 32-bit
+    - 9p/net: fix memory leak in p9_client_create
+    - ASoC: fsl_esai: fix register setting issue in RIGHT_J mode
+    - ASoC: codecs: pcm186x: fix wrong usage of DECLARE_TLV_DB_SCALE()
+    - ASoC: codecs: pcm186x: Fix energysense SLEEP bit
+    - iio: adc: exynos-adc: Fix NULL pointer exception on unbind
+    - iio: adc: exynos-adc: Use proper number of channels for Exynos4x12
+    - mei: hbm: clean the feature flags on link reset
+    - mei: bus: move hw module get/put to probe/release
+    - stm class: Prevent division by zero
+    - stm class: Fix an endless loop in channel allocation
+    - crypto: caam - fix hash context DMA unmap size
+    - crypto: ccree - fix missing break in switch statement
+    - crypto: caam - fixed handling of sg list
+    - crypto: caam - fix DMA mapping of stack memory
+    - crypto: ccree - fix free of unallocated mlli buffer
+    - crypto: ccree - unmap buffer before copying IV
+    - crypto: ccree - don't copy zero size ciphertext
+    - crypto: cfb - add missing 'chunksize' property
+    - crypto: cfb - remove bogus memcpy() with src == dest
+    - crypto: ofb - fix handling partial blocks and make thread-safe
+    - crypto: ahash - fix another early termination in hash walk
+    - crypto: rockchip - fix scatterlist nents error
+    - crypto: rockchip - update new iv to device in multiple operations
+    - dax: Flush partial PMDs correctly
+    - nfit: Fix nfit_intel_shutdown_status() command submission
+    - nfit: acpi_nfit_ctl(): Check out_obj->type in the right place
+    - acpi/nfit: Fix bus command validation
+    - nfit/ars: Attempt a short-ARS whenever the ARS state is idle at boot
+    - nfit/ars: Attempt short-ARS even in the no_init_ars case
+    - libnvdimm/label: Clear 'updating' flag after label-set update
+    - libnvdimm, pfn: Fix over-trim in trim_pfn_device()
+    - libnvdimm/pmem: Honor force_raw for legacy pmem regions
+    - libnvdimm: Fix altmap reservation size calculation
+    - fix cgroup_do_mount() handling of failure exits
+    - crypto: aead - set CRYPTO_TFM_NEED_KEY if ->setkey() fails
+    - crypto: aegis - fix handling chunked inputs
+    - crypto: arm/crct10dif - revert to C code for short inputs
+    - crypto: arm64/aes-neonbs - fix returning final keystream block
+    - crypto: arm64/crct10dif - revert to C code for short inputs
+    - crypto: hash - set CRYPTO_TFM_NEED_KEY if ->setkey() fails
+    - crypto: morus - fix handling chunked inputs
+    - crypto: pcbc - remove bogus memcpy()s with src == dest
+    - crypto: skcipher - set CRYPTO_TFM_NEED_KEY if ->setkey() fails
+    - crypto: testmgr - skip crc32c context test for ahash algorithms
+    - crypto: x86/aegis - fix handling chunked inputs and MAY_SLEEP
+    - crypto: x86/aesni-gcm - fix crash on empty plaintext
+    - crypto: x86/morus - fix handling chunked inputs and MAY_SLEEP
+    - crypto: arm64/aes-ccm - fix logical bug in AAD MAC handling
+    - crypto: arm64/aes-ccm - fix bugs in non-NEON fallback routine
+    - CIFS: Fix leaking locked VFS cache pages in writeback retry
+    - CIFS: Do not reset lease state to NONE on lease break
+    - CIFS: Do not skip SMB2 message IDs on send failures
+    - CIFS: Fix read after write for files with read caching
+    - smb3: make default i/o size for smb3 mounts larger
+    - tracing: Use strncpy instead of memcpy for string keys in hist triggers
+    - tracing: Do not free iter->trace in fail path of tracing_open_pipe()
+    - tracing/perf: Use strndup_user() instead of buggy open-coded version
+    - vmw_balloon: release lock on error in vmballoon_reset()
+    - xen: fix dom0 boot on huge systems
+    - ACPI / device_sysfs: Avoid OF modalias creation for removed device
+    - mmc: sdhci-esdhc-imx: fix HS400 timing issue
+    - mmc: renesas_sdhi: Fix card initialization failure in high speed mode
+    - mmc:fix a bug when max_discard is 0
+    - spi: ti-qspi: Fix mmap read when more than one CS in use
+    - spi: pxa2xx: Setup maximum supported DMA transfer length
+    - spi: omap2-mcspi: Fix DMA and FIFO event trigger size mismatch
+    - spi: spi-gpio: fix SPI_CS_HIGH capability
+    - regulator: s2mps11: Fix steps for buck7, buck8 and LDO35
+    - regulator: max77620: Initialize values for DT properties
+    - regulator: s2mpa01: Fix step values for some LDOs
+    - mt76: fix corrupted software generated tx CCMP PN
+    - clocksource/drivers/exynos_mct: Move one-shot check from tick clear to ISR
+    - clocksource/drivers/exynos_mct: Clear timer interrupt when shutdown
+    - clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer
+      instability
+    - s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
+    - s390/setup: fix early warning messages
+    - s390/virtio: handle find on invalid queue gracefully
+    - scsi: virtio_scsi: don't send sc payload with tmfs
+    - scsi: aacraid: Fix performance issue on logical drives
+    - scsi: sd: Optimal I/O size should be a multiple of physical block size
+    - scsi: target/iscsi: Avoid iscsit_release_commands_from_conn() deadlock
+    - scsi: qla2xxx: Fix LUN discovery if loop id is not assigned yet by firmware
+    - scsi: qla2xxx: Avoid PCI IRQ affinity mapping when multiqueue is not
+      supported
+    - scsi: qla2xxx: Use complete switch scan for RSCN events
+    - fs/devpts: always delete dcache dentry-s in dput()
+    - splice: don't merge into linked buffers
+    - ovl: During copy up, first copy up data and then xattrs
+    - ovl: Do not lose security.capability xattr over metadata file copy-up
+    - m68k: Add -ffreestanding to CFLAGS
+    - Btrfs: setup a nofs context for memory allocation at btrfs_create_tree()
+    - Btrfs: setup a nofs context for memory allocation at __btrfs_set_acl
+    - btrfs: scrub: fix circular locking dependency warning
+    - btrfs: drop the lock on error in btrfs_dev_replace_cancel
+    - btrfs: ensure that a DUP or RAID1 block group has exactly two stripes
+    - btrfs: init csum_list before possible free
+    - Btrfs: fix corruption reading shared and compressed extents after hole
+      punching
+    - Btrfs: fix deadlock between clone/dedupe and rename
+    - soc: qcom: rpmh: Avoid accessing freed memory from batch API
+    - libertas_tf: don't set URB_ZERO_PACKET on IN USB transfer
+    - irqchip/gic-v3-its: Avoid parsing _indirect_ twice for Device table
+    - irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
+    - x86/kprobes: Prohibit probing on optprobe template code
+    - cpufreq: kryo: Release OPP tables on module removal
+    - cpufreq: tegra124: add missing of_node_put()
+    - cpufreq: pxa2xx: remove incorrect __init annotation
+    - ext4: fix check of inode in swap_inode_boot_loader
+    - ext4: cleanup pagecache before swap i_data
+    - mm: hwpoison: fix thp split handing in soft_offline_in_use_page()
+    - mm/vmalloc: fix size check for remap_vmalloc_range_partial()
+    - mm/memory.c: do_fault: avoid usage of stale vm_area_struct
+    - kernel/sysctl.c: add missing range check in do_proc_dointvec_minmax_conv
+    - nvmem: core: don't check the return value of notifier chain call
+    - device property: Fix the length used in PROPERTY_ENTRY_STRING()
+    - intel_th: Don't reference unassigned outputs
+    - parport_pc: fix find_superio io compare code, should use equal test.
+    - i2c: tegra: fix maximum transfer size
+    - i2c: tegra: update maximum transfer size
+    - media: i2c: ov5640: Fix post-reset delay
+    - gpio: pca953x: Fix dereference of irq data in shutdown
+    - ext4: update quota information while swapping boot loader inode
+    - ext4: add mask of ext4 flags to swap
+    - ext4: fix crash during online resizing
+    - dma: Introduce dma_max_mapping_size()
+    - swiotlb: Introduce swiotlb_max_mapping_size()
+    - swiotlb: Add is_swiotlb_active() function
+    - PCI/ASPM: Use LTR if already enabled by platform
+    - PCI/DPC: Fix print AER status in DPC event handling
+    - PCI: qcom: Don't deassert reset GPIO during probe
+    - PCI: dwc: skip MSI init if MSIs have been explicitly disabled
+    - PCI: pci-bridge-emul: Create per-bridge copy of register behavior
+    - PCI: pci-bridge-emul: Extend pci_bridge_emul_init() with flags
+    - IB/hfi1: Close race condition on user context disable and close
+    - IB/rdmavt: Fix loopback send with invalidate ordering
+    - IB/rdmavt: Fix concurrency panics in QP post_send and modify to error
+    - cxl: Wrap iterations over afu slices inside 'afu_list_lock'
+    - ext2: Fix underflow in ext2_max_size()
+    - clk: uniphier: Fix update register for CPU-gear
+    - clk: clk-twl6040: Fix imprecise external abort for pdmclk
+    - clk: samsung: exynos5: Fix possible NULL pointer exception on
+      platform_device_alloc() failure
+    - clk: samsung: exynos5: Fix kfree() of const memory on setting
+      driver_override
+    - clk: ingenic: Fix round_rate misbehaving with non-integer dividers
+    - clk: ingenic: Fix doc of ingenic_cgu_div_info
+    - usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
+    - usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
+    - dmaengine: usb-dmac: Make DMAC system sleep callbacks explicit
+    - serial: uartps: Fix stuck ISR if RX disabled with non-empty FIFO
+    - serial: 8250_of: assume reg-shift of 2 for mrvl,mmp-uart
+    - serial: 8250_pci: Fix number of ports for ACCES serial cards
+    - serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954
+      chip use the pci_pericom_setup()
+    - jbd2: clear dirty flag when revoking a buffer from an older transaction
+    - jbd2: fix compile warning when using JBUFFER_TRACE
+    - selinux: add the missing walk_size + len check in selinux_sctp_bind_connect
+    - security/selinux: fix SECURITY_LSM_NATIVE_LABELS on reused superblock
+    - powerpc/32: Clear on-stack exception marker upon exception return
+    - powerpc/wii: properly disable use of BATs when requested.
+    - powerpc/powernv: Make opal log only readable by root
+    - powerpc/83xx: Also save/restore SPRG4-7 during suspend
+    - powerpc/kvm: Save and restore host AMR/IAMR/UAMOR
+    - powerpc/powernv: Don't reprogram SLW image on every KVM guest entry/exit
+    - powerpc/64s/hash: Fix assert_slb_presence() use of the slbfee. instruction
+    - powerpc: Fix 32-bit KVM-PR lockup and host crash with MacOS guest
+    - powerpc/ptrace: Simplify vr_get/set() to avoid GCC warning
+    - powerpc/hugetlb: Don't do runtime allocation of 16G pages in LPAR
+      configuration
+    - powerpc/smp: Fix NMI IPI timeout
+    - powerpc/smp: Fix NMI IPI xmon timeout
+    - powerpc/traps: fix recoverability of machine check handling on book3s/32
+    - powerpc/traps: Fix the message printed when stack overflows
+    - ARM: s3c24xx: Fix boolean expressions in osiris_dvs_notify
+    - arm64: Fix HCR.TGE status for NMI contexts
+    - arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
+    - arm64: debug: Ensure debug handlers check triggering exception level
+    - arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
+    - Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
+    - ipmi_si: Fix crash when using hard-coded device
+    - ipmi_si: fix use-after-free of resource->name
+    - dm: fix to_sector() for 32bit
+    - dm integrity: limit the rate of error messages
+    - media: cx25840: mark pad sig_types to fix cx231xx init
+    - mfd: sm501: Fix potential NULL pointer dereference
+    - cpcap-charger: generate events for userspace
+    - cpuidle: governor: Add new governors to cpuidle_governors again
+    - NFS: Fix I/O request leakages
+    - NFS: Fix an I/O request leakage in nfs_do_recoalesce
+    - NFS: Don't recoalesce on error in nfs_pageio_complete_mirror()
+    - nfsd: fix performance-limiting session calculation
+    - nfsd: fix memory corruption caused by readdir
+    - nfsd: fix wrong check in write_v4_end_grace()
+    - NFSv4.1: Reinitialise sequence results before retransmitting a request
+    - svcrpc: fix UDP on servers with lots of threads
+    - PM / wakeup: Rework wakeup source timer cancellation
+    - PM / OPP: Update performance state when freq == old_freq
+    - bcache: treat stale && dirty keys as bad keys
+    - bcache: use (REQ_META|REQ_PRIO) to indicate bio for metadata
+    - stable-kernel-rules.rst: add link to networking patch queue
+    - vt: perform safe console erase in the right order
+    - x86/unwind/orc: Fix ORC unwind table alignment
+    - perf intel-pt: Fix CYC timestamp calculation after OVF
+    - perf tools: Fix split_kallsyms_for_kcore() for trampoline symbols
+    - perf auxtrace: Define auxtrace record alignment
+    - perf intel-pt: Fix overlap calculation for padding
+    - perf/x86/intel/uncore: Fix client IMC events return huge result
+    - perf intel-pt: Fix divide by zero when TSC is not available
+    - md: Fix failed allocation of md_register_thread
+    - x86/kvmclock: set offset for kvm unstable clock
+    - x86/ftrace: Fix warning and considate ftrace_jmp_replace() and
+      ftrace_call_replace()
+    - tpm/tpm_crb: Avoid unaligned reads in crb_recv()
+    - tpm: Unify the send callback behaviour
+    - rcu: Do RCU GP kthread self-wakeup from softirq and interrupt
+    - media: imx: prpencvf: Stop upstream before disabling IDMA channel
+    - media: lgdt330x: fix lock status reporting
+    - media: sun6i: Fix CSI regmap's max_register
+    - media: uvcvideo: Avoid NULL pointer dereference at the end of streaming
+    - media: vimc: Add vimc-streamer for stream control
+    - media: imx-csi: Input connections to CSI should be optional
+    - media: imx: csi: Disable CSI immediately after last EOF
+    - media: imx: csi: Stop upstream before disabling IDMA channel
+    - drm/fb-helper: generic: Fix drm_fbdev_client_restore()
+    - drm/radeon/evergreen_cs: fix missing break in switch statement
+    - drm/amd/powerplay: correct power reading on fiji
+    - drm/amd/display: don't call dm_pp_ function from an fpu block
+    - KVM: Call kvm_arch_memslots_updated() before updating memslots
+    - KVM: VMX: Compare only a single byte for VMCS' "launched" in vCPU-run
+    - KVM: VMX: Zero out *all* general purpose registers after VM-Exit
+    - KVM: x86/mmu: Detect MMIO generation wrap in any address space
+    - KVM: x86/mmu: Do not cache MMIO accesses while memslots are in flux
+    - KVM: nVMX: Sign extend displacements of VMX instr's mem operands
+    - KVM: nVMX: Apply addr size mask to effective address for VMX instructions
+    - KVM: nVMX: Ignore limit checks on VMX instructions using flat segments
+    - KVM: nVMX: Check a single byte for VMCS "launched" in nested early checks
+    - net: dsa: lantiq_gswip: fix use-after-free on failed probe
+    - net: dsa: lantiq_gswip: fix OF child-node lookups
+    - s390/setup: fix boot crash for machine without EDAT-1
+    - SUNRPC: Prevent thundering herd when the socket is not connected
+    - SUNRPC: Fix up RPC back channel transmission
+    - SUNRPC: Respect RPC call timeouts when retrying transmission
+    - Linux 5.0.4
+    - [Config] update configs for 5.0.4 stable update
+
+  * New Intel Wireless-AC 9260 [8086:2526] card not correctly probed in Ubuntu
+    system (LP: #1821271)
+    - iwlwifi: add new card for 9260 series
+
+  * [CONFIG] please enable highdpi font FONT_TER16x32 (LP: #1819881)
+    - [Config]: enable highdpi Terminus 16x32 font support
+
+  * [SRU][B/B-OEM/C/D] Fix AMD IOMMU NULL dereference (LP: #1820990)
+    - iommu/amd: Fix NULL dereference bug in match_hid_uid
+
+  * some codecs stop working after S3 (LP: #1820930)
+    - ALSA: hda - Enforces runtime_resume after S3 and S4 for each codec
+    - ALSA: hda - Don't trigger jackpoll_work in azx_resume
+
+  * tcm_loop.ko: move from modules-extra into main modules package
+    (LP: #1817786)
+    - [Packaging] move tcm_loop.lo to main linux-modules package
+
+  * C++ demangling support missing from perf (LP: #1396654)
+    - [Packaging] fix a mistype
+
+  * r8169 doesn't get woken up by ethernet cable plugging, no PME generated
+    (LP: #1817676)
+    - PCI: pciehp: Disable Data Link Layer State Changed event on suspend
+
+  * Disco update: v5.0.3 upstream stable release (LP: #1821074)
+    - connector: fix unsafe usage of ->real_parent
+    - fou, fou6: avoid uninit-value in gue_err() and gue6_err()
+    - gro_cells: make sure device is up in gro_cells_receive()
+    - ipv4/route: fail early when inet dev is missing
+    - l2tp: fix infoleak in l2tp_ip6_recvmsg()
+    - lan743x: Fix RX Kernel Panic
+    - lan743x: Fix TX Stall Issue
+    - net: hsr: fix memory leak in hsr_dev_finalize()
+    - net/hsr: fix possible crash in add_timer()
+    - net: sit: fix UBSAN Undefined behaviour in check_6rd
+    - net/x25: fix use-after-free in x25_device_event()
+    - net/x25: reset state in x25_connect()
+    - pptp: dst_release sk_dst_cache in pptp_sock_destruct
+    - ravb: Decrease TxFIFO depth of Q3 and Q2 to one
+    - route: set the deleted fnhe fnhe_daddr to 0 in ip_del_fnhe to fix a race
+    - rxrpc: Fix client call queueing, waiting for channel
+    - sctp: remove sched init from sctp_stream_init
+    - tcp: do not report TCP_CM_INQ of 0 for closed connections
+    - tcp: Don't access TCP_SKB_CB before initializing it
+    - tcp: handle inet_csk_reqsk_queue_add() failures
+    - vxlan: Fix GRO cells race condition between receive and link delete
+    - vxlan: test dev->flags & IFF_UP before calling gro_cells_receive()
+    - net/mlx4_core: Fix reset flow when in command polling mode
+    - net/mlx4_core: Fix locking in SRIOV mode when switching between events and
+      polling
+    - net/mlx4_core: Fix qp mtt size calculation
+    - net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports
+    - vsock/virtio: fix kernel panic from virtio_transport_reset_no_sock
+    - net: sched: flower: insert new filter to idr after setting its mask
+    - f2fs: wait on atomic writes to count F2FS_CP_WB_DATA
+    - perf/x86: Fixup typo in stub functions
+    - ALSA: bebob: use more identical mod_alias for Saffire Pro 10 I/O against
+      Liquid Saffire 56
+    - ALSA: firewire-motu: fix construction of PCM frame for capture direction
+    - ALSA: hda: Extend i915 component bind timeout
+    - ALSA: hda - add more quirks for HP Z2 G4 and HP Z240
+    - ALSA: hda/realtek: Enable audio jacks of ASUS UX362FA with ALC294
+    - ALSA: hda/realtek - Reduce click noise on Dell Precision 5820 headphone
+    - ALSA: hda/realtek: Enable headset MIC of Acer TravelMate X514-51T with
+      ALC255
+    - perf/x86/intel: Fix memory corruption
+    - perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
+    - It's wrong to add len to sector_nr in raid10 reshape twice
+    - drm: Block fb changes for async plane updates
+    - Linux 5.0.3
+
+  * Disco update: v5.0.2 upstream stable release (LP: #1820318)
+    - media: uvcvideo: Fix 'type' check leading to overflow
+    - Input: wacom_serial4 - add support for Wacom ArtPad II tablet
+    - Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
+    - iscsi_ibft: Fix missing break in switch statement
+    - scsi: aacraid: Fix missing break in switch statement
+    - x86/PCI: Fixup RTIT_BAR of Intel Denverton Trace Hub
+    - arm64: dts: zcu100-revC: Give wifi some time after power-on
+    - arm64: dts: hikey: Give wifi some time after power-on
+    - arm64: dts: hikey: Revert "Enable HS200 mode on eMMC"
+    - ARM: dts: exynos: Fix pinctrl definition for eMMC RTSN line on Odroid X2/U3
+    - ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
+    - ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
+    - drm: disable uncached DMA optimization for ARM and arm64
+    - media: Revert "media: rc: some events are dropped by userspace"
+    - Revert "PCI/PME: Implement runtime PM callbacks"
+    - bpf: Stop the psock parser before canceling its work
+    - gfs2: Fix missed wakeups in find_insert_glock
+    - staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()
+    - staging: erofs: compressed_pages should not be accessed again after freed
+    - scripts/gdb: replace flags (MS_xyz -> SB_xyz)
+    - ath9k: Avoid OF no-EEPROM quirks without qca,no-eeprom
+    - perf/x86/intel: Make cpuc allocations consistent
+    - perf/x86/intel: Generalize dynamic constraint creation
+    - x86: Add TSX Force Abort CPUID/MSR
+    - perf/x86/intel: Implement support for TSX Force Abort
+    - Linux 5.0.2
+
+  * Linux security module stacking support
+    - LSM: Introduce LSM_FLAG_LEGACY_MAJOR
+    - LSM: Provide separate ordered initialization
+    - LSM: Plumb visibility into optional "enabled" state
+    - LSM: Lift LSM selection out of individual LSMs
+    - LSM: Build ordered list of LSMs to initialize
+    - LSM: Introduce CONFIG_LSM
+    - LSM: Introduce "lsm=" for boottime LSM selection
+    - LSM: Tie enabling logic to presence in ordered list
+    - LSM: Prepare for reorganizing "security=" logic
+    - LSM: Refactor "security=" in terms of enable/disable
+    - LSM: Separate idea of "major" LSM from "exclusive" LSM
+    - apparmor: Remove SECURITY_APPARMOR_BOOTPARAM_VALUE
+    - selinux: Remove SECURITY_SELINUX_BOOTPARAM_VALUE
+    - LSM: Add all exclusive LSMs to ordered initialization
+    - LSM: Split LSM preparation from initialization
+    - LoadPin: Initialize as ordered LSM
+    - Yama: Initialize as ordered LSM
+    - LSM: Introduce enum lsm_order
+    - capability: Initialize as LSM_ORDER_FIRST
+    - procfs: add smack subdir to attrs
+    - Smack: Abstract use of cred security blob
+    - SELinux: Abstract use of cred security blob
+    - SELinux: Remove cred security blob poisoning
+    - SELinux: Remove unused selinux_is_enabled
+    - AppArmor: Abstract use of cred security blob
+    - TOMOYO: Abstract use of cred security blob
+    - Infrastructure management of the cred security blob
+    - SELinux: Abstract use of file security blob
+    - Smack: Abstract use of file security blob
+    - LSM: Infrastructure management of the file security
+    - SELinux: Abstract use of inode security blob
+    - Smack: Abstract use of inode security blob
+    - LSM: Infrastructure management of the inode security
+    - LSM: Infrastructure management of the task security
+    - SELinux: Abstract use of ipc security blobs
+    - Smack: Abstract use of ipc security blobs
+    - LSM: Infrastructure management of the ipc security blob
+    - TOMOYO: Update LSM flags to no longer be exclusive
+    - LSM: generalize flag passing to security_capable
+    - LSM: Make lsm_early_cred() and lsm_early_task() local functions.
+    - LSM: Make some functions static
+    - apparmor: Adjust offset when accessing task blob.
+    - LSM: Ignore "security=" when "lsm=" is specified
+    - LSM: Update list of SECURITYFS users in Kconfig
+    - apparmor: delete the dentry in aafs_remove() to avoid a leak
+    - apparmor: fix double free when unpack of secmark rules fails
+    - SAUCE: LSM: Infrastructure management of the sock security
+    - SAUCE: LSM: Limit calls to certain module hooks
+    - SAUCE: LSM: Special handling for secctx lsm hooks
+    - SAUCE: LSM: Specify which LSM to display with /proc/self/attr/display
+    - SAUCE: Fix-up af_unix mediation for sock infrastructure management
+    - SAUCE: Revert "apparmor: Fix warning about unused function
+      apparmor_ipv6_postroute"
+    - SAUCE: Revert "apparmor: fix checkpatch error in Parse secmark policy"
+    - SAUCE: Revert "apparmor: add #ifdef checks for secmark filtering"
+    - SAUCE: Revert "apparmor: Allow filtering based on secmark policy"
+    - SAUCE: Revert "apparmor: Parse secmark policy"
+    - SAUCE: Revert "apparmor: Add a wildcard secid"
+    - SAUCE: Revert "apparmor: fix bad debug check in apparmor_secid_to_secctx()"
+    - SAUCE: Revert "apparmor: fixup secid map conversion to using IDR"
+    - SAUCE: Revert "apparmor: Use an IDR to allocate apparmor secids"
+    - SAUCE: Revert "apparmor: Fix memory leak of rule on error exit path"
+    - SAUCE: Revert "apparmor: modify audit rule support to support profile
+      stacks"
+    - SAUCE: Revert "apparmor: Add support for audit rule filtering"
+    - SAUCE: Revert "apparmor: add the ability to get a task's secid"
+    - SAUCE: Revert "apparmor: add support for mapping secids and using secctxes"
+    - SAUCE: apparmor: add proc subdir to attrs
+    - SAUCE: apparmor: add an apparmorfs entry to access current attrs
+    - SAUCE: apparmor: update flags to no longer be exclusive
+    - SAUCE: update configs and annotations for LSM stacking
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_EARLY_PRINTK_USB_XDBC=y
+    - SAUCE: (efi-lockdown) bpf: Restrict kernel image access functions when the
+      kernel is locked down
+    - [Config] CONFIG_RANDOM_TRUST_CPU=y
+    - [Config] refresh annotations for recent config changes
+    - ubuntu: vbox -- update to 6.0.4-dfsg-7
+    - Revert "UBUNTU: SAUCE: i2c:amd I2C Driver based on PCI Interface for
+      upcoming platform"
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 04 Apr 2019 14:49:59 -0500
+
+linux (5.0.0-8.9) disco; urgency=medium
+
+  * linux: 5.0.0-8.9 -proposed tracker (LP: #1819759)
+
+  * hisi_sas: add debugfs support (LP: #1819500)
+    - scsi: hisi_sas: Create root and device debugfs directories
+    - scsi: hisi_sas: Alloc debugfs snapshot buffer memory for all registers
+    - scsi: hisi_sas: Take debugfs snapshot for all regs
+    - scsi: hisi_sas: Debugfs global register create file and add file operations
+    - scsi: hisi_sas: Add debugfs for port registers
+    - scsi: hisi_sas: Add debugfs CQ file and add file operations
+    - scsi: hisi_sas: Add debugfs DQ file and add file operations
+    - scsi: hisi_sas: Add debugfs IOST file and add file operations
+    - scsi: hisi_sas: No need to check return value of debugfs_create functions
+    - scsi: hisi_sas: Fix type casting and missing static qualifier in debugfs
+      code
+    - scsi: hisi_sas: Add debugfs ITCT file and add file operations
+
+  * [disco] hns driver updates from 5.1 merge window (LP: #1819535)
+    - net: hns: Use struct_size() in devm_kzalloc()
+    - net: hns3: modify enet reinitialization interface
+    - net: hns3: remove unused member in struct hns3_enet_ring
+    - net: hns3: remove unnecessary hns3_adjust_tqps_num
+    - net: hns3: reuse reinitialization interface in the hns3_set_channels
+    - net: hns3: add interface hclge_tm_bp_setup
+    - net: hns3: modify parameter checks in the hns3_set_channels
+    - net: hns3: remove redundant codes in hclge_knic_setup
+    - net: hns3: fix user configuration loss for ethtool -L
+    - net: hns3: adjust the use of alloc_tqps and num_tqps
+    - net: hns3: fix wrong combined count returned by ethtool -l
+    - net: hns3: do reinitialization while ETS configuration changed
+    - net: hns3: add HNAE3_RESTORE_CLIENT interface in enet module
+    - net: hns3: add calling roce callback function when link status change
+    - net: hns3: add rx multicast packets statistic
+    - net: hns3: refactor the statistics updating for netdev
+    - net: hns3: fix rss configuration lost problem when setting channel
+    - net: hns3: fix for shaper not setting when TC num changes
+    - net: hns3: fix bug of ethtool_ops.get_channels for VF
+    - net: hns3: clear param in ring when free ring
+    - net: hns3: Change fw error code NOT_EXEC to NOT_SUPPORTED
+    - net: hns3: do not return GE PFC setting err when initializing
+    - net: hns3: add ETS TC weight setting in SSU module
+    - net: hns3: add statistics for PFC frames and MAC control frames
+    - net: hns3: fix PFC not setting problem for DCB module
+    - net: hns3: don't update packet statistics for packets dropped by hardware
+    - net: hns3: clear pci private data when unload hns3 driver
+    - net: hns3: add error handling in hclge_ieee_setets
+    - net: hns3: fix return value handle issue for hclge_set_loopback()
+    - net: hns3: fix broadcast promisc issue for revision 0x20
+    - net: hns3: After setting the loopback, add the status of getting MAC
+    - net: hns3: do reinitialization while mqprio configuration changed
+    - net: hns3: remove dcb_ops->map_update in hclge_dcb
+    - net: hns3: call hns3_nic_set_real_num_queue with netdev down
+    - net: hns3: add 8 BD limit for tx flow
+    - net: hns3: add initialization for nic state
+    - net: hns3: don't allow vf to enable promisc mode
+    - net: hns3: reuse the definition of l3 and l4 header info union
+    - net: hns3: fix VF dump register issue
+    - net: hns3: use the correct interface to stop|open port
+    - net: hns3: change hnae3_register_ae_dev() to int
+    - net: hns3: only support tc 0 for VF
+    - net: hns3: Fix NULL deref when unloading driver
+    - net: hns3: fix netif_napi_del() not do problem when unloading
+    - net: hns3: fix for rss result nonuniform
+    - net: hns3: fix improper error handling in the hclge_init_ae_dev()
+    - net: hns3: fix an issue for hclgevf_ae_get_hdev
+    - net: hns3: stop sending keep alive msg to PF when VF is resetting
+    - net: hns3: keep flow director state unchanged when reset
+    - net: hns3: Check for allocation failure
+    - net: hns3: fix a code style issue for hns3_update_new_int_gl()
+    - net: hns3: fix an issue for hns3_update_new_int_gl
+    - net: hns3: Modify parameter type from int to bool in set_gro_en
+    - net: hns3: code optimization for hclge_rx_buffer_calc
+    - net: hns3: add hclge_cmd_check_retval() to parse comman's return value
+    - net: hns3: move some set_bit statement into hclge_prepare_mac_addr
+    - net: hns3: fix a wrong checking in the hclge_tx_buffer_calc()
+    - net: hns3: fix the problem that the supported port is empty
+    - net: hns3: optimize the maximum TC macro
+    - net: hns3: don't allow user to change vlan filter state
+    - net: hns3: modify the upper limit judgment condition
+    - net: hns3: MAC table entry count function increases operation 0 value
+      protection measures
+    - net: hns3: make function hclge_set_all_vf_rst() static
+    - net: hns3: add pointer checking at the beginning of the exported functions.
+    - net: hns3: Check variable is valid before assigning it to another
+    - net: hns3: convert mac advertize and supported from u32 to link mode
+    - net: hns3: fix port info query issue for copper port
+    - net: hns3: modify print message of ssu common ecc errors
+    - net: hns3: some bugfix of ppu(rcb) ras errors
+    - net: hns3: enable 8~11th bit of mac common msi-x error
+    - net: hns3: fix 6th bit of ppp mpf abnormal errors
+    - net: hns3: Record VF unicast and multicast tables
+    - net: hns3: Record VF vlan tables
+    - net: hns3: uninitialize command queue while unloading PF driver
+    - net: hns3: clear command queue's registers when unloading VF driver
+    - net: hns3: add xps setting support for hns3 driver
+    - net: hns3: avoid mult + div op in critical data path
+    - net: hns3: limit some variable scope in critical data path
+    - net: hns3: remove some ops in struct hns3_nic_ops
+    - net: hns3: add unlikely for error handling in data path
+    - net: hns3: replace hnae3_set_bit and hnae3_set_field in data path
+    - net: hns3: remove hnae3_get_bit in data path
+    - net: hns3: add support to config depth for tx|rx ring separately
+    - net: hns3: enable VF VLAN filter for each VF when initializing
+    - net: hns3: fix get VF RSS issue
+    - net: hns3: fix setting of the hns reset_type for rdma hw errors
+    - net: hns3: fix improper error handling for hns3_client_start
+    - net: hns: use struct_size() in devm_kzalloc()
+    - net: hns3: Fix a logical vs bitwise typo
+    - net: hns3: add dma_rmb() for rx description
+    - net: hns3: fix to stop multiple HNS reset due to the AER changes
+
+  * Build Nvidia drivers in conjunction with kernel (LP: #1764792)
+    - [Packaging] dkms-build -- support building against packages in PPAs
+    - [Packaging] dkms-build: do not redownload files on subsequent passes
+    - [Packaging] dkms-build -- elide partial Built-Using information
+    - [Packaging] dkms-build -- remove retpoline data from final binary packages
+    - [Packaging] dkms-build--nvidia* -- check gcc version against primary build
+    - [Packaging] dkms-build -- add support for unversioned overrides
+    - [Packaging] dkms-build--nvidia-* -- convert to generic -N form
+    - [Packaging] fix-filenames -- handle exact string removal
+    - [Packaging] dkms-build--nvidia-N -- remove GCC versions
+
+  * Disco update: v5.0.1 upstream stable release (LP: #1819515)
+    - cpufreq: Use struct kobj_attribute instead of struct global_attr
+    - staging: erofs: fix mis-acted TAIL merging behavior
+    - binder: create node flag to request sender's security context
+    - USB: serial: option: add Telit ME910 ECM composition
+    - USB: serial: cp210x: add ID for Ingenico 3070
+    - USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
+    - driver core: Postpone DMA tear-down until after devres release
+    - staging: erofs: fix fast symlink w/o xattr when fs xattr is on
+    - staging: erofs: fix memleak of inode's shared xattr array
+    - staging: erofs: fix race of initializing xattrs of a inode at the same time
+    - staging: erofs: fix illegal address access under memory pressure
+    - staging: comedi: ni_660x: fix missing break in switch statement
+    - staging: wilc1000: fix to set correct value for 'vif_num'
+    - staging: android: ion: fix sys heap pool's gfp_flags
+    - staging: android: ashmem: Don't call fallocate() with ashmem_mutex held.
+    - staging: android: ashmem: Avoid range_alloc() allocation with ashmem_mutex
+      held.
+    - ip6mr: Do not call __IP6_INC_STATS() from preemptible context
+    - net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new
+      DSA framework
+    - net: dsa: mv88e6xxx: handle unknown duplex modes gracefully in
+      mv88e6xxx_port_set_duplex
+    - net: dsa: mv8e6xxx: fix number of internal PHYs for 88E6x90 family
+    - net: mscc: Enable all ports in QSGMII
+    - net: sched: put back q.qlen into a single location
+    - net-sysfs: Fix mem leak in netdev_register_kobject
+    - qmi_wwan: Add support for Quectel EG12/EM12
+    - sctp: call iov_iter_revert() after sending ABORT
+    - team: Free BPF filter when unregistering netdev
+    - tipc: fix RDM/DGRAM connect() regression
+    - x86/CPU/AMD: Set the CPB bit unconditionally on F17h
+    - x86/boot/compressed/64: Do not read legacy ROM on EFI system
+    - tracing: Fix event filters and triggers to handle negative numbers
+    - xhci: tegra: Prevent error pointer dereference
+    - usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on
+      INTEL_SUNRISEPOINT_LP_XHCI
+    - applicom: Fix potential Spectre v1 vulnerabilities
+    - alpha: wire up io_pgetevents system call
+    - MIPS: irq: Allocate accurate order pages for irq stack
+    - aio: Fix locking in aio_poll()
+    - xtensa: fix get_wchan
+    - gnss: sirf: fix premature wakeup interrupt enable
+    - USB: serial: cp210x: fix GPIO in autosuspend
+    - Revert "selftests: firmware: add CONFIG_FW_LOADER_USER_HELPER_FALLBACK to
+      config"
+    - Revert "selftests: firmware: remove use of non-standard diff -Z option"
+    - selftests: firmware: fix verify_reqs() return value
+    - Bluetooth: btrtl: Restore old logic to assume firmware is already loaded
+    - Bluetooth: Fix locking in bt_accept_enqueue() for BH context
+    - Linux 5.0.1
+
+  * sky2 ethernet card doesn't work after returning from suspend
+    (LP: #1807259) // sky2 ethernet card link not up after suspend
+    (LP: #1809843) // Disco update: v5.0.1 upstream stable release
+    (LP: #1819515)
+    - sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
+
+  * tls selftest failures/hangs on i386 (LP: #1813607)
+    - [Config] CONFIG_TLS=n for i386
+
+  * CVE-2019-8980
+    - exec: Fix mem leak in kernel_read_file
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests: net: Use 'ipproto ipv6-icmp' to match ICMPv6 headers
+    - [Config] enable nvidia build
+    - [Config] update gcc version to 8.3
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: selftests: pmtu: disable accept_dad for tests"
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Tue, 12 Mar 2019 16:15:44 -0300
+
+linux (5.0.0-7.8) disco; urgency=medium
+
+  * linux: 5.0.0-7.8 -proposed tracker (LP: #1818519)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * unnecessary request_queue freeze (LP: #1815733)
+    - block: avoid setting nr_requests to current value
+    - block: avoid setting none scheduler if it's already none
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests: net: Don't fail test_vxlan_under_vrf on xfail
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 04 Mar 2019 08:46:10 -0600
+
+linux (5.0.0-6.7) disco; urgency=medium
+
+  * linux: 5.0.0-6.7 -proposed tracker (LP: #1817585)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - [Packaging] resync getabis
+
+  * installer does not support iSCSI iBFT (LP: #1817321)
+    - d-i: add iscsi_ibft to scsi-modules
+
+  * Silent "Unknown key" message when pressing keyboard backlight hotkey
+    (LP: #1817063)
+    - platform/x86: dell-wmi: Ignore new keyboard backlight change event
+
+  * Fix I219 doesn't get woken up after plugging ethernet cable (LP: #1817058)
+    - e1000e: Disable runtime PM on CNP+
+
+  * efi/arm/arm64: Allow SetVirtualAddressMap() to be omitted (LP: #1814982)
+    - efi/arm/arm64: Allow SetVirtualAddressMap() to be omitted
+
+  * CVE-2019-3460
+    - Bluetooth: Check L2CAP option sizes returned from l2cap_get_conf_opt
+
+  * CVE-2019-3459
+    - Bluetooth: Verify that l2cap_get_conf_opt provides large enough buffer
+
+  * kernel net tls selftest fails on 5.0 (LP: #1816716)
+    - SAUCE: Revert "selftests/tls: Add test for recv(PEEK) spanning across
+      multiple records"
+
+  * Please enable CONFIG_DMA_CMA=y on arm64 (LP: #1803206)
+    - [Config] annotations -- enforce CONFIG_DMA_CMA and update notes
+
+  * [19.04 FEAT] [LS1801] PCI Virtual function enablement (LP: #1814684)
+    - s390/pci: map IOV resources
+    - s390/pci: improve bar check
+
+  * glibc 2.28-0ubuntu1 ADT test failure with linux 5.0.0-1.2 (LP: #1813060)
+    - SAUCE: prevent a glibc test failure when looking for obsolete types on
+      headers
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enforce CONFIG_ZCRYPT_MULTIDEVNODES in annotations
+    - SAUCE: selftests: pmtu: disable accept_dad for tests
+    - SAUCE: arm64: add kernel config option to lock down when in Secure Boot mode
+    - SAUCE: selftests: net: Make test for VXLAN underlay in non-default VRF an
+      expected failure
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc8
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 25 Feb 2019 09:37:36 -0600
+
+linux (5.0.0-5.6) disco; urgency=medium
+
+  * [ALSA] [PATCH] System76 darp5 and oryp5 fixups (LP: #1815831)
+    - ALSA: hda/realtek - Headset microphone and internal speaker support for
+      System76 oryp5
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Fix aufs menus in annotations file
+    - [Config] CONFIG_SAMPLE_TRACE_PRINTK=m
+    - [Config] Update annotations based on configs
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 18 Feb 2019 10:04:11 +0100
+
+linux (5.0.0-4.5) disco; urgency=medium
+
+  * linux-buildinfo: pull out ABI information into its own package
+    (LP: #1806380)
+    - [Packaging] autoreconstruct -- base tag is always primary mainline version
+
+  * [Packaging] Allow overlay of config annotations (LP: #1752072)
+    - [Packaging] config-check: Add an include directive
+
+  * Miscellaneous Ubuntu changes
+    - hio -- stub out BIOVEC_PHYS_MERGEABLE for 4.20+
+    - hio -- replace use of do_gettimeofday()
+    - hio -- part_round_stats() removed in 5.0
+    - hio -- device_add_disk() grew a 'groups' argument in 4.20
+    - enable hio build
+    - Revert "UBUNTU: [Packaging] autoreconstruct -- base tag is always primary
+      mainline version"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 12 Feb 2019 08:15:32 -0600
+
+linux (5.0.0-3.4) disco; urgency=medium
+
+  * CONFIG_TEST_BPF is disabled (LP: #1813955)
+    - [Config]: Reenable TEST_BPF
+
+  * Ignore "incomplete report" from Elan touchpanels (LP: #1813733)
+    - HID: i2c-hid: Ignore input report if there's no data present on Elan
+      touchpanels
+
+  * SecureBoot support for arm64 (LP: #1804481)
+    - Build signed kernels for arm64
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests: net: fix "from" match test in fib_rule_tests.sh
+    - [Config] CONFIG_PCMCIA=n for arm64 and s390x
+    - [Config] CONFIG_SERIAL_SC16IS7XX=n for s390x
+    - [Config] disable I2C TPM drivers for s390x
+    - [Config] CONFIG_RAPIDIO=n for s390x
+    - [Config] CONFIG_DMADEVICES=n for s390x
+    - [Config] disable gpio drivers for s390x
+    - [Config] CONFIG_SENSORS_OCC_P8_I2C=m for ppc64el
+    - [Config] disable I2C hardware drivers for s390x
+    - [Config] CONFIG_I3C=n for s390x
+    - [Config] CONFIG_SERIO=n for s390x
+    - [Config] disable misc drivers for s390x
+    - [Config] disable EEPROM drivers for s390x
+    - [Config] disable MFD drivers for s390x
+    - [Config] CONFIG_NVMEM=n for s390x
+    - [Config] CONFIG_MLXSW_I2C=n for s390x
+    - [Config] CONFIG_NET_VENDOR_MICROCHIP=n for s390x
+    - [Config] CONFIG_PPP=n for s390x
+    - [Config] CONFIG_PCCARD=n for s390x
+    - [Config] CONFIG_PCI_MESON=y
+    - [Config] CONFIG_SCSI_MYRB=n for s390x
+    - [Config] CONFIG_REGULATOR=n for s390x
+    - [Config] CONFIG_ZIIRAVE_WATCHDOG=n for s390x
+    - [Config] CONFIG_NCSI_OEM_CMD_GET_MAC=y
+    - [Config] update annotations following config review
+    - [Packaging] remove handoff check for uefi signing
+    - [Packaging] decompress gzipped efi images in signing tarball
+    - vbox-update: allow leading whitespace when fixing up KERN_DIR
+    - ubuntu: vbox -- update to 6.0.4-dfsg-3
+    - vbox: remove remount check in sf_read_super_aux()
+    - enable vbox build
+    - [Config] CONFIG_ANDROID_BINDER_DEVICES=""
+    - SAUCE: import aufs driver
+    - [Config]: Enable aufs
+    - [Config] relocate aufs annotations to menu
+    - [Config] remove unmatched configs from annotations
+    - [Config] fix up abi for removed modules
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) module: remove support for having IMA validate modules
+    - SAUCE: (efi-lockdown) Move EFI signature blob parser to shared location
+    - SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI Secure Boot
+    - SAUCE: (efi-lockdown) MODSIGN: Allow the "db" UEFI variable to be suppressed
+    - [Config] (efi-lockdown) enable importing of efi certificates for module sig
+      verification
+
+  * Miscellaneous upstream changes
+    - binder: fix CONFIG_ANDROID_BINDER_DEVICES
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 05 Feb 2019 14:26:12 -0600
+
+linux (5.0.0-2.3) disco; urgency=medium
+
+  * kernel oops in bcache module (LP: #1793901)
+    - SAUCE: bcache: never writeback a discard operation
+
+  * Enable sound card power saving by default (LP: #1804265)
+    - [Config] CONFIG_SND_HDA_POWER_SAVE_DEFAULT=1
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: SAUCE: selftests: disable some failing networking tests"
+    - SAUCE: ashmem: turn into module
+    - SAUCE: binder: turn into module
+    - SAUCE: binder: give binder_alloc its own debug mask file
+    - [Config] enable binder and ashmem as modules
+    - SAUCE: selftests: net: replace AF_MAX with INT_MAX in socket.c
+    - SAUCE: selftests/ftrace: Fix tab expansion in trace_marker snapshot trigger
+      test
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 29 Jan 2019 06:57:32 -0600
+
+linux (5.0.0-1.2) disco; urgency=medium
+
+  * Fix non-working QCA Rome Bluetooth after S3 (LP: #1812812)
+    - USB: Add new USB LPM helpers
+    - USB: Consolidate LPM checks to avoid enabling LPM twice
+
+  * bluetooth controller not detected with 4.15 kernel (LP: #1810797)
+    - SAUCE: btqcomsmd: introduce BT_QCOMSMD_HACK
+    - [Config] arm64: snapdragon: BT_QCOMSMD_HACK=y
+
+  * [19.04 FEAT| Enable virtio-gpu for s390x (LP: #1799467)
+    - [Config] enable virtio-gpu for s390x
+
+  * Crash on "ip link add foo type ipip" (LP: #1811803)
+    - SAUCE: fan: Fix NULL pointer dereference
+
+  * Fix not working Goodix touchpad (LP: #1811929)
+    - HID: i2c-hid: Disable runtime PM on Goodix touchpad
+
+  * Miscellaneous Ubuntu changes
+    - update dkms package versions
+    - enable zfs build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 22 Jan 2019 13:56:17 -0600
+
+linux (5.0.0-0.1) disco; urgency=medium
+
+  * Build Nvidia drivers in conjunction with kernel (LP: #1764792)
+    - [Packaging] dkms -- add per package post-process step
+    - [Packaging] dkms -- switch to a consistent build prefix length and strip
+    - [Packaging] nvidia -- build and sign nvidia packages and ship signatures
+    - [Packaging] nvidia -- make nvidia package version explicit
+
+  * Add support for ALC3277 codec on new Dell edge gateways (LP: #1807334)
+    - [Config] CONFIG_SND_SOC_INTEL_KBL_RT5660_MACH=m
+
+  * RTL8822BE WiFi Disabled in Kernel 4.18.0-12 (LP: #1806472)
+    - [Config] CONFIG_RTLWIFI_DEBUG_ST=n
+
+  * Miscellaneous Ubuntu changes
+    - ubuntu -- disable vbox build
+    - ubuntu -- disable hio build
+    - Disable zfs build
+    - SAUCE: import aufs driver
+    - update dkms package versions
+    - [Config] disable aufs config options
+    - [Config] disable nvidia build
+    - update dropped.txt
+    - [Packaging] disable nvidia dkms builds for mainline
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Lock down module params that specify hardware
+      parameters (eg. ioport)
+    - SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the testmmiotrace module
+    - SAUCE: (efi-lockdown) Lock down /proc/kcore
+    - SAUCE: (efi-lockdown) Lock down kprobes
+    - SAUCE: (efi-lockdown) Lock down perf
+    - SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) debugfs: avoid EPERM when no open file operation
+      defined
+    - SAUCE: (efi-lockdown) KEYS: Allow unrestricted boot-time addition of keys to
+      secondary keyring
+    - SAUCE: (efi-lockdown) Make get_cert_list() not complain about cert lists
+      that aren't present.
+    - SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err().
+    - SAUCE: (efi-lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - [Config] set config options for efi lockdown
+    - Revert "UBUNTU: SAUCE: import aufs driver"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v5.0-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 17 Jan 2019 12:31:29 -0600
+
+linux (5.0.0-0.0) disco; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 16 Jan 2019 14:48:05 -0600
+
+linux (4.20.0-2.3) disco; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.20
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 03 Jan 2019 12:11:43 -0600
+
+linux (4.20.0-1.2) disco; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Power leakage at S5 with Qualcomm Atheros QCA9377 802.11ac Wireless Network
+    Adapter (LP: #1805607)
+    - SAUCE: ath10k: provide reset function for QCA9377 chip
+
+  * zfs/spl build in conjunction with the kernel from DKMS source (LP: #1807378)
+    - [Packaging] dkms -- dkms package build packaging support
+    - [Packaging] dkms -- save build objects artifacts for validation
+    - [Packaging] dkms -- add general Built-Using: support
+    - [Packaging] simplify Provides comma handling
+    - [Packaging] zfs/spl -- remove packaging support for incorporated source
+    - [Packaging] zfs/spl -- remove incorporated source
+    - [Packaging] zfs/spl -- build via dkms
+    - [Packaging] zfs/spl -- make zfs package version explicit
+    - [Packaging] update-version-dkms -- sync archive versions to package
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] update-version-dkms -- fix getting distrbution from changelog
+    - update dkms package versions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.20-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 11 Dec 2018 11:33:08 -0600
+
+linux (4.20.0-0.1) disco; urgency=medium
+
+  * Overlayfs in user namespace leaks directory content of inaccessible
+    directories (LP: #1793458) // CVE-2018-6559
+    - Revert "ovl: relax permission checking on underlying layers"
+    - SAUCE: overlayfs: ensure mounter privileges when reading directories
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Lock down module params that specify hardware
+      parameters (eg. ioport)
+    - SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the testmmiotrace module
+    - SAUCE: (efi-lockdown) Lock down /proc/kcore
+    - SAUCE: (efi-lockdown) Lock down kprobes
+    - SAUCE: (efi-lockdown) Lock down perf
+    - SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) KEYS: Allow unrestricted boot-time addition of keys to
+      secondary keyring
+    - SAUCE: (efi-lockdown) efi: Add EFI signature data types
+    - SAUCE: (efi-lockdown) efi: Add an EFI signature blob parser
+    - SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI Secure Boot
+    - SAUCE: (efi-lockdown) MODSIGN: Allow the "db" UEFI variable to be suppressed
+    - SAUCE: (efi-lockdown) Make get_cert_list() not complain about cert lists
+      that aren't present.
+    - SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err().
+    - SAUCE: (efi-lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) Fix for module sig verification
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: Import aufs driver
+    - ubuntu: vbox -- update to 5.2.22-dfsg-2
+    - ubuntu -- disable vbox build
+    - ubuntu -- disable hio build
+    - Disable zfs build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.20-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 07 Dec 2018 07:13:42 -0600
+
+linux (4.20.0-0.0) disco; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 06 Dec 2018 10:20:19 -0600
+
+linux (4.19.0-8.9) disco; urgency=medium
+
+  * linux: 4.19.0-8.9 -proposed tracker (LP: #1806952)
+
+  * Workaround CSS timeout on AMD SNPS 3.0 xHC (LP: #1806838)
+    - xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
+
+  * Fix Intel I210 doesn't work when ethernet cable gets plugged (LP: #1806818)
+    - igb: Fix an issue that PME is not enabled during runtime suspend
+
+  * The line-out on the Dell Dock station can't work (LP: #1806532)
+    - ALSA: usb-audio: Add vendor and product name for Dell WD19 Dock
+
+  * CVE-2018-19407
+    - KVM: X86: Fix scan ioapic use-before-initialization
+
+  * PC SN720 NVMe WDC 256GB consumes more power in S2Idle than during long idle
+    (LP: #1805775)
+    - SAUCE: pci/nvme: prevent WDC PC SN720 NVMe from entering D3 and being
+      disabled
+
+  * Disco update: 4.19.6 upstream stable release (LP: #1806909)
+    - HID: steam: remove input device when a hid client is running.
+    - efi/libstub: arm: support building with clang
+    - usb: core: Fix hub port connection events lost
+    - usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
+    - usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
+    - usb: dwc3: core: Clean up ULPI device
+    - usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
+    - xhci: Fix leaking USB3 shared_hcd at xhci removal
+    - xhci: handle port status events for removed USB3 hcd
+    - xhci: Add check for invalid byte size error when UAS devices are connected.
+    - usb: xhci: fix uninitialized completion when USB3 port got wrong status
+    - usb: xhci: fix timeout for transition from RExit to U0
+    - xhci: Add quirk to workaround the errata seen on Cavium Thunder-X2 Soc
+    - usb: xhci: Prevent bus suspend if a port connect change or polling state is
+      detected
+    - ALSA: oss: Use kvzalloc() for local buffer allocations
+    - MAINTAINERS: Add Sasha as a stable branch maintainer
+    - Documentation/security-bugs: Clarify treatment of embargoed information
+    - Documentation/security-bugs: Postpone fix publication in exceptional cases
+    - mmc: sdhci-pci: Try "cd" for card-detect lookup before using NULL
+    - mmc: sdhci-pci: Workaround GLK firmware failing to restore the tuning value
+    - gpio: don't free unallocated ida on gpiochip_add_data_with_key() error path
+    - iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE
+    - iwlwifi: mvm: support sta_statistics() even on older firmware
+    - iwlwifi: mvm: fix regulatory domain update when the firmware starts
+    - iwlwifi: mvm: don't use SAR Geo if basic SAR is not used
+    - brcmfmac: fix reporting support for 160 MHz channels
+    - opp: ti-opp-supply: Dynamically update u_volt_min
+    - opp: ti-opp-supply: Correct the supply in _get_optimal_vdd_voltage call
+    - tools/power/cpupower: fix compilation with STATIC=true
+    - v9fs_dir_readdir: fix double-free on p9stat_read error
+    - selinux: Add __GFP_NOWARN to allocation at str_read()
+    - Input: synaptics - avoid using uninitialized variable when probing
+    - bfs: add sanity check at bfs_fill_super()
+    - sctp: clear the transport of some out_chunk_list chunks in
+      sctp_assoc_rm_peer
+    - gfs2: Don't leave s_fs_info pointing to freed memory in init_sbd
+    - llc: do not use sk_eat_skb()
+    - mm: don't warn about large allocations for slab
+    - mm/memory.c: recheck page table entry with page table lock held
+    - tcp: do not release socket ownership in tcp_close()
+    - drm/fb-helper: Blacklist writeback when adding connectors to fbdev
+    - drm/amdgpu: Add missing firmware entry for HAINAN
+    - drm/vc4: Set ->legacy_cursor_update to false when doing non-async updates
+    - drm/amdgpu: Fix oops when pp_funcs->switch_power_profile is unset
+    - drm/i915: Disable LP3 watermarks on all SNB machines
+    - drm/ast: change resolution may cause screen blurred
+    - drm/ast: fixed cursor may disappear sometimes
+    - drm/ast: Remove existing framebuffers before loading driver
+    - can: flexcan: Unlock the MB unconditionally
+    - can: dev: can_get_echo_skb(): factor out non sending code to
+      __can_get_echo_skb()
+    - can: dev: __can_get_echo_skb(): replace struct can_frame by canfd_frame to
+      access frame length
+    - can: dev: __can_get_echo_skb(): Don't crash the kernel if can_priv::echo_skb
+      is accessed out of bounds
+    - can: dev: __can_get_echo_skb(): print error message, if trying to echo non
+      existing skb
+    - can: rx-offload: introduce can_rx_offload_get_echo_skb() and
+      can_rx_offload_queue_sorted() functions
+    - can: rx-offload: rename can_rx_offload_irq_queue_err_skb() to
+      can_rx_offload_queue_tail()
+    - can: flexcan: use can_rx_offload_queue_sorted() for flexcan_irq_bus_*()
+    - can: flexcan: handle tx-complete CAN frames via rx-offload infrastructure
+    - can: raw: check for CAN FD capable netdev in raw_sendmsg()
+    - can: hi311x: Use level-triggered interrupt
+    - can: flexcan: Always use last mailbox for TX
+    - can: flexcan: remove not needed struct flexcan_priv::tx_mb and struct
+      flexcan_priv::tx_mb_idx
+    - ACPICA: AML interpreter: add region addresses in global list during
+      initialization
+    - IB/hfi1: Eliminate races in the SDMA send error path
+    - fsnotify: generalize handling of extra event flags
+    - fanotify: fix handling of events on child sub-directory
+    - pinctrl: meson: fix pinconf bias disable
+    - pinctrl: meson: fix gxbb ao pull register bits
+    - pinctrl: meson: fix gxl ao pull register bits
+    - pinctrl: meson: fix meson8 ao pull register bits
+    - pinctrl: meson: fix meson8b ao pull register bits
+    - tools/testing/nvdimm: Fix the array size for dimm devices.
+    - scsi: lpfc: fix remoteport access
+    - scsi: hisi_sas: Remove set but not used variable 'dq_list'
+    - KVM: PPC: Move and undef TRACE_INCLUDE_PATH/FILE
+    - cpufreq: imx6q: add return value check for voltage scale
+    - rtc: cmos: Do not export alarm rtc_ops when we do not support alarms
+    - rtc: pcf2127: fix a kmemleak caused in pcf2127_i2c_gather_write
+    - crypto: simd - correctly take reqsize of wrapped skcipher into account
+    - floppy: fix race condition in __floppy_read_block_0()
+    - powerpc/io: Fix the IO workarounds code to work with Radix
+    - sched/fair: Fix cpu_util_wake() for 'execl' type workloads
+    - perf/x86/intel/uncore: Add more IMC PCI IDs for KabyLake and CoffeeLake CPUs
+    - block: copy ioprio in __bio_clone_fast() and bounce
+    - SUNRPC: Fix a bogus get/put in generic_key_to_expire()
+    - riscv: add missing vdso_install target
+    - RISC-V: Silence some module warnings on 32-bit
+    - drm/amdgpu: fix bug with IH ring setup
+    - kdb: Use strscpy with destination buffer size
+    - NFSv4: Fix an Oops during delegation callbacks
+    - powerpc/numa: Suppress "VPHN is not supported" messages
+    - efi/arm: Revert deferred unmap of early memmap mapping
+    - z3fold: fix possible reclaim races
+    - mm, memory_hotplug: check zone_movable in has_unmovable_pages
+    - tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
+    - mm, page_alloc: check for max order in hot path
+    - dax: Avoid losing wakeup in dax_lock_mapping_entry
+    - include/linux/pfn_t.h: force '~' to be parsed as an unary operator
+    - tty: wipe buffer.
+    - tty: wipe buffer if not echoing data
+    - gfs2: Fix iomap buffer head reference counting bug
+    - rcu: Make need_resched() respond to urgent RCU-QS needs
+    - media: ov5640: Re-work MIPI startup sequence
+    - media: ov5640: Fix timings setup code
+    - media: ov5640: fix exposure regression
+    - media: ov5640: fix auto gain & exposure when changing mode
+    - media: ov5640: fix wrong binning value in exposure calculation
+    - media: ov5640: fix auto controls values when switching to manual mode
+    - Linux 4.19.6
+
+  * linux-buildinfo: pull out ABI information into its own package
+    (LP: #1806380)
+    - [Packaging] limit preparation to linux-libc-dev in headers
+    - [Packaging] commonise debhelper invocation
+    - [Packaging] ABI -- accumulate abi information at the end of the build
+    - [Packaging] buildinfo -- add basic build information
+    - [Packaging] buildinfo -- add firmware information to the flavour ABI
+    - [Packaging] buildinfo -- add compiler information to the flavour ABI
+    - [Packaging] buildinfo -- add buildinfo support to getabis
+    - [Packaging] getabis -- handle all known package combinations
+    - [Packaging] getabis -- support parsing a simple version
+
+  * linux packages should own /usr/lib/linux/triggers (LP: #1770256)
+    - [Packaging] own /usr/lib/linux/triggers
+
+  * Miscellaneous upstream changes
+    - blk-mq: fix corruption with direct issue
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 05 Dec 2018 09:18:30 -0600
+
+linux (4.19.0-7.8) disco; urgency=medium
+
+  * linux: 4.19.0-7.8 -proposed tracker (LP: #1805465)
+
+  * Fix and issue that LG I2C touchscreen stops working after reboot
+    (LP: #1805085)
+    - HID: i2c-hid: Disable runtime PM for LG touchscreen
+
+  * click/pop noise in the headphone on several lenovo laptops (LP: #1805079) //
+    click/pop noise in the headphone on several lenovo laptops (LP: #1805079)
+    - ALSA: hda/realtek - fix the pop noise on headphone for lenovo laptops
+
+  * Regression: hinic performance degrades over time (LP: #1805248)
+    - Revert "net-next/hinic: add checksum offload and TSO support"
+
+  * Disco update: 4.19.5 upstream stable release (LP: #1805461)
+    - drm/i915: Replace some PAGE_SIZE with I915_GTT_PAGE_SIZE
+    - cifs: don't dereference smb_file_target before null check
+    - cifs: fix return value for cifs_listxattr
+    - arm64: kprobe: make page to RO mode when allocate it
+    - block: brd: associate with queue until adding disk
+    - net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
+    - net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
+    - net: hns3: bugfix for handling mailbox while the command queue reinitialized
+    - net: hns3: bugfix for the initialization of command queue's spin lock
+    - ixgbe: fix MAC anti-spoofing filter after VFLR
+    - reiserfs: propagate errors from fill_with_dentries() properly
+    - hfs: prevent btree data loss on root split
+    - hfsplus: prevent btree data loss on root split
+    - perf unwind: Take pgoff into account when reporting elf to libdwfl
+    - um: Give start_idle_thread() a return code
+    - drm/edid: Add 6 bpc quirk for BOE panel.
+    - afs: Handle EIO from delivery function
+    - platform/x86: intel_telemetry: report debugfs failure
+    - clk: fixed-rate: fix of_node_get-put imbalance
+    - perf symbols: Set PLT entry/header sizes properly on Sparc
+    - fs/exofs: fix potential memory leak in mount option parsing
+    - clk: samsung: exynos5420: Enable PERIS clocks for suspend
+    - apparmor: Fix uninitialized value in aa_split_fqname
+    - x86/earlyprintk: Add a force option for pciserial device
+    - platform/x86: acerhdf: Add BIOS entry for Gateway LT31 v1.3307
+    - clk: meson-axg: pcie: drop the mpll3 clock parent
+    - arm64: percpu: Initialize ret in the default case
+    - clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
+    - clk: renesas: r9a06g032: Fix UART34567 clock rate
+    - clk: ti: fix OF child-node lookup
+    - serial: sh-sci: Fix receive on SCIFA/SCIFB variants with DMA
+    - netfilter: ipv6: fix oops when defragmenting locally generated fragments
+    - netfilter: bridge: define INT_MIN & INT_MAX in userspace
+    - s390/decompressor: add missing FORCE to build targets
+    - s390/vdso: add missing FORCE to build targets
+    - HID: i2c-hid: Add a small delay after sleep command for Raydium touchpanel
+    - Revert "HID: add NOGET quirk for Eaton Ellipse MAX UPS"
+    - HID: alps: allow incoming reports when only the trackstick is opened
+    - Revert "netfilter: nft_numgen: add map lookups for numgen random operations"
+    - netfilter: ipset: list:set: Decrease refcount synchronously on deletion and
+      replace
+    - netfilter: ipset: actually allow allowable CIDR 0 in hash:net,port,net
+    - netfilter: ipset: fix ip_set_list allocation failure
+    - s390/mm: fix mis-accounting of pgtable_bytes
+    - s390/mm: Fix ERROR: "__node_distance" undefined!
+    - bpf: fix bpf_prog_get_info_by_fd to return 0 func_lens for unpriv
+    - netfilter: ipset: Correct rcu_dereference() call in ip_set_put_comment()
+    - netfilter: xt_IDLETIMER: add sysfs filename checking routine
+    - netfilter: ipset: Fix calling ip_set() macro at dumping
+    - netfilter: nft_compat: ebtables 'nat' table is normal chain type
+    - s390/qeth: fix HiperSockets sniffer
+    - s390/qeth: unregister netdevice only when registered
+    - net: hns3: Fix for out-of-bounds access when setting pfc back pressure
+    - hwmon: (ibmpowernv) Remove bogus __init annotations
+    - ARM: dts: imx6sll: fix typo for fsl,imx6sll-i2c node
+    - ARM: dts: fsl: Fix improperly quoted stdout-path values
+    - Revert "drm/exynos/decon5433: implement frame counter"
+    - arm64: dts: renesas: r8a7795: add missing dma-names on hscif2
+    - arm64: dts: renesas: condor: switch from EtherAVB to GEther
+    - xen/grant-table: Fix incorrect gnttab_dma_free_pages() pr_debug message
+    - clk: fixed-factor: fix of_node_get-put imbalance
+    - mtd: nand: Fix nanddev_pos_next_page() kernel-doc header
+    - lib/raid6: Fix arm64 test build
+    - drm/amd/display: Stop leaking planes
+    - block: Clear kernel memory before copying to user
+    - drm/amd/display: Drop reusing drm connector for MST
+    - drm/amd/amdgpu/dm: Fix dm_dp_create_fake_mst_encoder()
+    - s390/perf: Change CPUM_CF return code in event init function
+    - ceph: quota: fix null pointer dereference in quota check
+    - of/device: Really only set bus DMA mask when appropriate
+    - nvme: make sure ns head inherits underlying device limits
+    - i2c: omap: Enable for ARCH_K3
+    - i2c: qcom-geni: Fix runtime PM mismatch with child devices
+    - sched/core: Take the hotplug lock in sched_init_smp()
+    - perf tools: Fix undefined symbol scnprintf in libperf-jvmti.so
+    - perf tools: Do not zero sample_id_all for group members
+    - ice: Fix dead device link issue with flow control
+    - ice: Fix the bytecount sent to netdev_tx_sent_queue
+    - ice: Change req_speeds to be u16
+    - i40e: restore NETIF_F_GSO_IPXIP[46] to netdev features
+    - qed: Fix memory/entry leak in qed_init_sp_request()
+    - qed: Fix blocking/unlimited SPQ entries leak
+    - qed: Fix SPQ entries not returned to pool in error flows
+    - qed: Fix potential memory corruption
+    - net: stmmac: Fix RX packet size > 8191
+    - net: aquantia: fix potential IOMMU fault after driver unbind
+    - net: aquantia: fixed enable unicast on 32 macvlan
+    - net: aquantia: invalid checksumm offload implementation
+    - kbuild: deb-pkg: fix too low build version number
+    - Revert "scripts/setlocalversion: git: Make -dirty check more robust"
+    - SUNRPC: drop pointless static qualifier in xdr_get_next_encode_buffer()
+    - x86/mm: Move LDT remap out of KASLR region on 5-level paging
+    - x86/ldt: Unmap PTEs for the slot before freeing LDT pages
+    - x86/ldt: Remove unused variable in map_ldt_struct()
+    - media: v4l: event: Add subscription to list before calling "add" operation
+    - MIPS: OCTEON: cavium_octeon_defconfig: re-enable OCTEON USB driver
+    - RISC-V: Fix raw_copy_{to,from}_user()
+    - uio: Fix an Oops on load
+    - ALSA: hda/realtek - Add quirk entry for HP Pavilion 15
+    - ALSA: hda/ca0132 - Call pci_iounmap() instead of iounmap()
+    - can: kvaser_usb: Fix accessing freed memory in kvaser_usb_start_xmit()
+    - can: kvaser_usb: Fix potential uninitialized variable use
+    - usb: cdc-acm: add entry for Hiro (Conexant) modem
+    - USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hub
+    - usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB
+    - misc: atmel-ssc: Fix section annotation on atmel_ssc_get_driver_data
+    - USB: misc: appledisplay: add 20" Apple Cinema Display
+    - gnss: serial: fix synchronous write timeout
+    - gnss: sirf: fix synchronous write timeout
+    - mtd: rawnand: atmel: fix OF child-node lookup
+    - drivers/misc/sgi-gru: fix Spectre v1 vulnerability
+    - ACPI / platform: Add SMB0001 HID to forbidden_id_list
+    - HID: uhid: forbid UHID_CREATE under KERNEL_DS or elevated privileges
+    - HID: Add quirk for Primax PIXART OEM mice
+    - HID: Add quirk for Microsoft PIXART OEM mouse
+    - libceph: fall back to sendmsg for slab pages
+    - mt76x0: run vco calibration for each channel configuration
+    - Linux 4.19.5
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: Build signed kernels for arm64"
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 27 Nov 2018 10:38:34 -0600
+
+linux (4.19.0-6.7) disco; urgency=medium
+
+  * linux: 4.19.0-6.7 -proposed tracker (LP: #1805195)
+
+  * SecureBoot support for arm64 (LP: #1804481)
+    - Build signed kernels for arm64
+
+  * Add pointstick support for Cirque Touchpad (LP: #1805081)
+    - HID: multitouch: Add pointstick support for Cirque Touchpad
+
+  * Power consumption during s2idle is higher than long idle (Intel SSDPEKKF)
+    (LP: #1804588)
+    - SAUCE: pci: prevent Intel NVMe SSDPEKKF from entering D3
+    - SAUCE: nvme: add quirk to not call disable function when suspending
+
+  * Disco update: 4.19.4 upstream stable release (LP: #1805159)
+    - flow_dissector: do not dissect l4 ports for fragments
+    - ibmvnic: fix accelerated VLAN handling
+    - ip_tunnel: don't force DF when MTU is locked
+    - ipv6: fix a dst leak when removing its exception
+    - ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
+    - net: bcmgenet: protect stop from timeout
+    - net-gro: reset skb->pkt_type in napi_reuse_skb()
+    - sctp: not allow to set asoc prsctp_enable by sockopt
+    - tcp: Fix SOF_TIMESTAMPING_RX_HARDWARE to use the latest timestamp during TCP
+      coalescing
+    - tg3: Add PHY reset for 5717/5719/5720 in change ring and flow control paths
+    - tipc: don't assume linear buffer when reading ancillary data
+    - tipc: fix lockdep warning when reinitilaizing sockets
+    - tuntap: fix multiqueue rx
+    - net: systemport: Protect stop from timeout
+    - net/sched: act_pedit: fix memory leak when IDR allocation fails
+    - net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
+    - tipc: fix link re-establish failure
+    - net/mlx5e: Don't match on vlan non-existence if ethertype is wildcarded
+    - net/mlx5e: Claim TC hw offloads support only under a proper build config
+    - net/mlx5e: Adjust to max number of channles when re-attaching
+    - net/mlx5e: RX, verify received packet size in Linear Striding RQ
+    - Revert "sctp: remove sctp_transport_pmtu_check"
+    - net/mlx5e: Always use the match level enum when parsing TC rule match
+    - net/mlx5e: Fix selftest for small MTUs
+    - net/mlx5e: Removed unnecessary warnings in FEC caps query
+    - inet: frags: better deal with smp races
+    - l2tp: fix a sock refcnt leak in l2tp_tunnel_register
+    - net/mlx5: IPSec, Fix the SA context hash key
+    - net/mlx5e: IPoIB, Reset QP after channels are closed
+    - net: dsa: mv88e6xxx: Fix clearing of stats counters
+    - net: phy: realtek: fix RTL8201F sysfs name
+    - sctp: define SCTP_SS_DEFAULT for Stream schedulers
+    - net: qualcomm: rmnet: Fix incorrect assignment of real_dev
+    - net: dsa: microchip: initialize mutex before use
+    - sctp: fix strchange_flags name for Stream Change Event
+    - net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
+    - sctp: not increase stream's incnt before sending addstrm_in request
+    - mlxsw: spectrum: Fix IP2ME CPU policer configuration
+    - net: smsc95xx: Fix MTU range
+    - rxrpc: Fix lockup due to no error backoff after ack transmit error
+    - usbnet: smsc95xx: disable carrier check while suspending
+    - Revert "x86/speculation: Enable cross-hyperthread spectre v2 STIBP
+      mitigation"
+    - Linux 4.19.4
+
+  * Disco update: 4.19.3 upstream stable release (LP: #1805158)
+    - powerpc/traps: restore recoverability of machine_check interrupts
+    - powerpc/64/module: REL32 relocation range check
+    - powerpc/mm: Fix page table dump to work on Radix
+    - powerpc/mm: fix always true/false warning in slice.c
+    - drm/amd/display: fix bug of accessing invalid memory
+    - Input: wm97xx-ts - fix exit path
+    - powerpc/Makefile: Fix PPC_BOOK3S_64 ASFLAGS
+    - powerpc/eeh: Fix possible null deref in eeh_dump_dev_log()
+    - tty: check name length in tty_find_polling_driver()
+    - tracing/kprobes: Check the probe on unloaded module correctly
+    - drm/nouveau/secboot/acr: fix memory leak
+    - drm/amdgpu/powerplay: fix missing break in switch statements
+    - ARM: imx_v6_v7_defconfig: Select CONFIG_TMPFS_POSIX_ACL
+    - powerpc/nohash: fix undefined behaviour when testing page size support
+    - drm/msm/gpu: fix parameters in function msm_gpu_crashstate_capture
+    - drm/msm/disp/dpu: Use proper define for drm_encoder_init() 'encoder_type'
+    - drm/msm: dpu: Allow planes to extend past active display
+    - powerpc/mm: Don't report hugepage tables as memory leaks when using kmemleak
+    - drm/omap: fix memory barrier bug in DMM driver
+    - drm/amd/display: Raise dispclk value for dce120 by 15%
+    - drm/amd/display: fix gamma not being applied
+    - drm/hisilicon: hibmc: Do not carry error code in HiBMC framebuffer pointer
+    - media: pci: cx23885: handle adding to list failure
+    - media: coda: don't overwrite h.264 profile_idc on decoder instance
+    - MIPS: kexec: Mark CPU offline before disabling local IRQ
+    - powerpc/boot: Ensure _zimage_start is a weak symbol
+    - powerpc/memtrace: Remove memory in chunks
+    - MIPS/PCI: Call pcie_bus_configure_settings() to set MPS/MRRS
+    - staging: erofs: fix a missing endian conversion
+    - serial: 8250_of: Fix for lack of interrupt support
+    - sc16is7xx: Fix for multi-channel stall
+    - media: tvp5150: fix width alignment during set_selection()
+    - powerpc/selftests: Wait all threads to join
+    - staging:iio:ad7606: fix voltage scales
+    - drm: rcar-du: Update Gen3 output limitations
+    - drm/amdgpu: Fix SDMA TO after GPU reset v3
+    - staging: most: video: fix registration of an empty comp core_component
+    - 9p locks: fix glock.client_id leak in do_lock
+    - udf: Prevent write-unsupported filesystem to be remounted read-write
+    - ARM: dts: imx6ull: keep IMX6UL_ prefix for signals on both i.MX6UL and
+      i.MX6ULL
+    - media: ov5640: fix mode change regression
+    - 9p: clear dangling pointers in p9stat_free
+    - drm/amdgpu: fix integer overflow test in amdgpu_bo_list_create()
+    - media: ov5640: fix restore of last mode set
+    - cdrom: fix improper type cast, which can leat to information leak.
+    - ovl: fix error handling in ovl_verify_set_fh()
+    - ovl: fix recursive oi->lock in ovl_link()
+    - ovl: check whiteout in ovl_create_over_whiteout()
+    - ovl: automatically enable redirect_dir on metacopy=on
+    - serial: sh-sci: Fix could not remove dev_attr_rx_fifo_timeout
+    - scsi: qla2xxx: Fix incorrect port speed being set for FC adapters
+    - scsi: qla2xxx: Fix process response queue for ISP26XX and above
+    - scsi: qla2xxx: Remove stale debug trace message from tcm_qla2xxx
+    - scsi: qla2xxx: Fix early srb free on abort
+    - scsi: qla2xxx: shutdown chip if reset fail
+    - scsi: qla2xxx: Reject bsg request if chip is down.
+    - scsi: qla2xxx: Fix re-using LoopID when handle is in use
+    - scsi: qla2xxx: Fix for double free of SRB structure
+    - scsi: qla2xxx: Fix NVMe session hang on unload
+    - scsi: qla2xxx: Fix NVMe Target discovery
+    - scsi: qla2xxx: Fix duplicate switch database entries
+    - scsi: qla2xxx: Fix driver hang when FC-NVMe LUNs are configured
+    - vfs: fix FIGETBSZ ioctl on an overlayfs file
+    - fuse: Fix use-after-free in fuse_dev_do_read()
+    - fuse: Fix use-after-free in fuse_dev_do_write()
+    - fuse: fix blocked_waitq wakeup
+    - fuse: set FR_SENT while locked
+    - drm/msm: fix OF child-node lookup
+    - arm64: dts: stratix10: Support Ethernet Jumbo frame
+    - arm64: dts: stratix10: fix multicast filtering
+    - clk: meson-gxbb: set fclk_div3 as CLK_IS_CRITICAL
+    - clk: meson: axg: mark fdiv2 and fdiv3 as critical
+    - zram: close udev startup race condition as default groups
+    - MIPS: Loongson-3: Fix CPU UART irq delivery problem
+    - MIPS: Loongson-3: Fix BRIDGE irq delivery problem
+    - xtensa: add NOTES section to the linker script
+    - xtensa: make sure bFLT stack is 16 byte aligned
+    - xtensa: fix boot parameters address translation
+    - um: Drop own definition of PTRACE_SYSEMU/_SINGLESTEP
+    - clk: s2mps11: Fix matching when built as module and DT node contains
+      compatible
+    - clk: at91: Fix division by zero in PLL recalc_rate()
+    - clk: sunxi-ng: h6: fix bus clocks' divider position
+    - clk: rockchip: fix wrong mmc sample phase shift for rk3328
+    - clk: rockchip: Fix static checker warning in rockchip_ddrclk_get_parent call
+    - libceph: bump CEPH_MSG_MAX_DATA_LEN
+    - Revert "ceph: fix dentry leak in splice_dentry()"
+    - thermal: core: Fix use-after-free in thermal_cooling_device_destroy_sysfs
+    - mach64: fix display corruption on big endian machines
+    - mach64: fix image corruption due to reading accelerator registers
+    - acpi/nfit, x86/mce: Handle only uncorrectable machine checks
+    - acpi/nfit, x86/mce: Validate a MCE's address before using it
+    - acpi, nfit: Fix ARS overflow continuation
+    - reset: hisilicon: fix potential NULL pointer dereference
+    - crypto: hisilicon - Fix NULL dereference for same dst and src
+    - crypto: hisilicon - Fix reference after free of memories on error path
+    - vhost/scsi: truncate T10 PI iov_iter to prot_bytes
+    - scsi: qla2xxx: Initialize port speed to avoid setting lower speed
+    - SCSI: fix queue cleanup race before queue initialization is done
+    - Revert "powerpc/8xx: Use L1 entry APG to handle _PAGE_ACCESSED for
+      CONFIG_SWAP"
+    - soc: ti: QMSS: Fix usage of irq_set_affinity_hint
+    - ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
+    - ocfs2: free up write context when direct IO failed
+    - mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
+    - memory_hotplug: cond_resched in __remove_pages
+    - netfilter: conntrack: fix calculation of next bucket number in early_drop
+    - ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm
+    - bonding/802.3ad: fix link_failure_count tracking
+    - mtd: spi-nor: cadence-quadspi: Return error code in
+      cqspi_direct_read_execute()
+    - mtd: nand: Fix nanddev_neraseblocks()
+    - mtd: docg3: don't set conflicting BCH_CONST_PARAMS option
+    - hwmon: (core) Fix double-free in __hwmon_device_register()
+    - perf cs-etm: Correct CPU mode for samples
+    - perf stat: Handle different PMU names with common prefix
+    - perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
+    - perf intel-pt/bts: Calculate cpumode for synthesized samples
+    - perf intel-pt: Insert callchain context into synthesized callchains
+    - of, numa: Validate some distance map rules
+    - x86/cpu/vmware: Do not trace vmware_sched_clock()
+    - x86/hyper-v: Enable PIT shutdown quirk
+    - termios, tty/tty_baudrate.c: fix buffer overrun
+    - arch/alpha, termios: implement BOTHER, IBSHIFT and termios2
+    - watchdog/core: Add missing prototypes for weak functions
+    - btrfs: fix pinned underflow after transaction aborted
+    - Btrfs: fix missing data checksums after a ranged fsync (msync)
+    - Btrfs: fix cur_offset in the error case for nocow
+    - Btrfs: fix infinite loop on inode eviction after deduplication of eof block
+    - Btrfs: fix data corruption due to cloning of eof block
+    - btrfs: tree-checker: Fix misleading group system information
+    - clockevents/drivers/i8253: Add support for PIT shutdown quirk
+    - ext4: add missing brelse() update_backups()'s error path
+    - ext4: add missing brelse() in set_flexbg_block_bitmap()'s error path
+    - ext4: add missing brelse() add_new_gdb_meta_bg()'s error path
+    - ext4: avoid potential extra brelse in setup_new_flex_group_blocks()
+    - ext4: missing !bh check in ext4_xattr_inode_write()
+    - ext4: fix possible inode leak in the retry loop of ext4_resize_fs()
+    - ext4: avoid buffer leak on shutdown in ext4_mark_iloc_dirty()
+    - ext4: avoid buffer leak in ext4_orphan_add() after prior errors
+    - ext4: fix missing cleanup if ext4_alloc_flex_bg_array() fails while resizing
+    - ext4: avoid possible double brelse() in add_new_gdb() on error path
+    - ext4: fix possible leak of sbi->s_group_desc_leak in error path
+    - ext4: fix possible leak of s_journal_flag_rwsem in error path
+    - ext4: fix buffer leak in ext4_xattr_get_block() on error path
+    - ext4: release bs.bh before re-using in ext4_xattr_block_find()
+    - ext4: fix buffer leak in ext4_xattr_move_to_block() on error path
+    - ext4: fix buffer leak in ext4_expand_extra_isize_ea() on error path
+    - ext4: fix buffer leak in __ext4_read_dirblock() on error path
+    - mount: Prevent MNT_DETACH from disconnecting locked mounts
+    - mnt: fix __detach_mounts infinite loop
+    - uapi: fix linux/kfd_ioctl.h userspace compilation errors
+    - ARM: cpuidle: Don't register the driver when back-end init returns -ENXIO
+    - kdb: use correct pointer when 'btc' calls 'btt'
+    - kdb: print real address of pointers instead of hashed addresses
+    - sunrpc: correct the computation for page_ptr when truncating
+    - NFSv4: Don't exit the state manager without clearing
+      NFS4CLNT_MANAGER_RUNNING
+    - nfsd: COPY and CLONE operations require the saved filehandle to be set
+    - rtc: hctosys: Add missing range error reporting
+    - fuse: fix use-after-free in fuse_direct_IO()
+    - fuse: fix leaked notify reply
+    - fuse: fix possibly missed wake-up after abort
+    - selinux: check length properly in SCTP bind hook
+    - gfs2: Put bitmap buffers in put_super
+    - gfs2: Fix metadata read-ahead during truncate (2)
+    - libata: blacklist SAMSUNG MZ7TD256HAFV-000L9 SSD
+    - crypto: user - fix leaking uninitialized memory to userspace
+    - lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
+    - hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
+    - mm/swapfile.c: use kvzalloc for swap_info_struct allocation
+    - efi/arm/libstub: Pack FDT after populating it
+    - mm: don't reclaim inodes with many attached pages
+    - scripts/spdxcheck.py: make python3 compliant
+    - drm/rockchip: Allow driver to be shutdown on reboot/kexec
+    - drm/amdgpu: Fix typo in amdgpu_vmid_mgr_init
+    - drm/amdgpu: add missing CHIP_HAINAN in amdgpu_ucode_get_load_type
+    - drm/amdgpu: Suppress keypresses from ACPI_VIDEO events
+    - drm/nouveau: Check backlight IDs are >= 0, not > 0
+    - drm/nouveau: Fix nv50_mstc->best_encoder()
+    - drm/amd/powerplay: Enable/Disable NBPSTATE on On/OFF of UVD
+    - drm/etnaviv: fix bogus fence complete check in timeout handler
+    - drm/dp_mst: Check if primary mstb is null
+    - drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
+    - drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit
+      panel's native mode
+    - drm/i915: Use the correct crtc when sanitizing plane mapping
+    - drm/i915: Restore vblank interrupts earlier
+    - drm/i915: Don't unset intel_connector->mst_port
+    - drm/i915: Skip vcpi allocation for MSTB ports that are gone
+    - drm/i915: Large page offsets for pread/pwrite
+    - drm/i915/dp: Fix link retraining comment in intel_dp_long_pulse()
+    - drm/i915/dp: Restrict link retrain workaround to external monitors
+    - drm/i915/icl: Fix the macros for DFLEXDPMLE register bits
+    - drm/i915/hdmi: Add HDMI 2.0 audio clock recovery N values
+    - drm/i915: Mark up GTT sizes as u64
+    - drm/i915: Fix error handling for the NV12 fb dimensions check
+    - drm/i915: Fix ilk+ watermarks when disabling pipes
+    - drm/i915: Compare user's 64b GTT offset even on 32b
+    - drm/i915: Don't oops during modeset shutdown after lpe audio deinit
+    - drm/i915: Mark pin flags as u64
+    - drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5
+    - drm/i915/execlists: Force write serialisation into context image vs
+      execution
+    - drm/i915: Fix possible race in intel_dp_add_mst_connector()
+    - drm/i915: Fix NULL deref when re-enabling HPD IRQs on systems with MST
+    - drm/i915: Fix hpd handling for pins with two encoders
+    - CONFIG_XEN_PV breaks xen_create_contiguous_region on ARM
+    - Revert "ACPICA: AML interpreter: add region addresses in global list during
+      initialization"
+    - Linux 4.19.3
+
+  * glibc 2.28-0ubuntu1 ADT test failure with linux 4.19.0-5.6 (LP: #1805154)
+    - SAUCE: Revert "x86: vdso: Use $LD instead of $CC to link"
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.7.12-1ubuntu1, zfs to 0.7.12-1ubuntu1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 26 Nov 2018 11:44:00 -0600
+
+linux (4.19.0-5.6) disco; urgency=medium
+
+  * crash in ENA driver on removing an interface (LP: #1802341)
+    - SAUCE: net: ena: fix crash during ena_remove()
+
+  * Ubuntu 18.04.1 - [s390x] Kernel panic while stressing network bonding
+    (LP: #1797367)
+    - s390/qeth: sanitize strings in debug messages
+
+  * Disco update: 4.19.2 upstream stable release (LP: #1803410)
+    - bpf: fix partial copy of map_ptr when dst is scalar
+    - MIPS: VDSO: Reduce VDSO_RANDOMIZE_SIZE to 64MB for 64bit
+    - gpio: mxs: Get rid of external API call
+    - mtd: rawnand: marvell: fix the IRQ handler complete() condition
+    - mtd: maps: gpio-addr-flash: Fix ioremapped size
+    - mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
+    - mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
+    - mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
+    - spi: spi-mem: Adjust op len based on message/transfer size limitations
+    - spi: bcm-qspi: switch back to reading flash using smaller chunks
+    - spi: bcm-qspi: fix calculation of address length
+    - bcache: trace missed reading by cache_missed
+    - bcache: fix ioctl in flash device
+    - bcache: correct dirty data statistics
+    - bcache: fix miss key refill->end in writeback
+    - hwmon: (pmbus) Fix page count auto-detection.
+    - jffs2: free jffs2_sb_info through jffs2_kill_sb()
+    - block: setup bounce bio_sets properly
+    - block: make sure discard bio is aligned with logical block size
+    - block: make sure writesame bio is aligned with logical block size
+    - cpufreq: conservative: Take limits changes into account properly
+    - dma-mapping: fix panic caused by passing empty cma command line argument
+    - pcmcia: Implement CLKRUN protocol disabling for Ricoh bridges
+    - ACPI / OSL: Use 'jiffies' as the time bassis for acpi_os_get_timer()
+    - ACPICA: AML interpreter: add region addresses in global list during
+      initialization
+    - ACPICA: AML Parser: fix parse loop to correctly skip erroneous extended
+      opcodes
+    - acpi, nfit: Fix Address Range Scrub completion tracking
+    - kprobes/x86: Use preempt_enable() in optimized_callback()
+    - mailbox: PCC: handle parse error
+    - parisc: Fix address in HPMC IVA
+    - parisc: Fix map_pages() to not overwrite existing pte entries
+    - parisc: Fix exported address of os_hpmc handler
+    - ALSA: hda - Add quirk for ASUS G751 laptop
+    - ALSA: hda - Fix headphone pin config for ASUS G751
+    - ALSA: hda - Add mic quirk for the Lenovo G50-30 (17aa:3905)
+    - ALSA: hda: Add 2 more models to the power_save blacklist
+    - ALSA: ca0106: Disable IZD on SB0570 DAC to fix audio pops
+    - ALSA: hda - Fix incorrect clearance of thinkpad_acpi hooks
+    - x86/speculation: Enable cross-hyperthread spectre v2 STIBP mitigation
+    - x86/xen: Fix boot loader version reported for PVH guests
+    - x86/corruption-check: Fix panic in memory_corruption_check() when boot
+      option without value is provided
+    - x86/kvm/nVMX: allow bare VMXON state migration
+    - x86/mm/pat: Disable preemption around __flush_tlb_all()
+    - x86/numa_emulation: Fix uniform-split numa emulation
+    - ARM: dts: exynos: Disable pull control for MAX8997 interrupts on Origen
+    - net: socionext: Reset tx queue in ndo_stop
+    - net: loopback: clear skb->tstamp before netif_rx()
+    - locking/lockdep: Fix debug_locks off performance problem
+    - netfilter: xt_nat: fix DNAT target for shifted portmap ranges
+    - ataflop: fix error handling during setup
+    - swim: fix cleanup on setup error
+    - arm64: cpufeature: ctr: Fix cpu capability check for late CPUs
+    - hv_netvsc: fix vf serial matching with pci slot info
+    - nfp: devlink port split support for 1x100G CXP NIC
+    - tun: Consistently configure generic netdev params via rtnetlink
+    - s390/sthyi: Fix machine name validity indication
+    - hwmon: (pwm-fan) Set fan speed to 0 on suspend
+    - lightnvm: pblk: fix race on sysfs line state
+    - lightnvm: pblk: fix two sleep-in-atomic-context bugs
+    - lightnvm: pblk: fix race condition on metadata I/O
+    - spi: spi-ep93xx: Use dma_data_direction for ep93xx_spi_dma_{finish,prepare}
+    - perf tools: Free temporary 'sys' string in read_event_files()
+    - perf tools: Cleanup trace-event-info 'tdata' leak
+    - perf tools: Free 'printk' string in parse_ftrace_printk()
+    - perf strbuf: Match va_{add,copy} with va_end
+    - cpupower: Fix coredump on VMWare
+    - bcache: Populate writeback_rate_minimum attribute
+    - mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01
+    - sdhci: acpi: add free_slot callback
+    - mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
+    - iwlwifi: pcie: avoid empty free RB queue
+    - iwlwifi: mvm: clear HW_RESTART_REQUESTED when stopping the interface
+    - iwlwifi: mvm: check for n_profiles validity in EWRD ACPI
+    - x86/olpc: Indicate that legacy PC XO-1 platform should not register RTC
+    - wlcore: Fix BUG with clear completion on timeout
+    - ACPI/PPTT: Handle architecturally unknown cache types
+    - ACPI / PM: LPIT: Register sysfs attributes based on FADT
+    - ACPI / processor: Fix the return value of acpi_processor_ids_walk()
+    - cpufreq: dt: Try freeing static OPPs only if we have added them
+    - x86/intel_rdt: Show missing resctrl mount options
+    - mtd: rawnand: atmel: Fix potential NULL pointer dereference
+    - nvme: call nvme_complete_rq when nvmf_check_ready fails for mpath I/O
+    - ath10k: fix tx status flag setting for management frames
+    - signal: Introduce COMPAT_SIGMINSTKSZ for use in compat_sys_sigaltstack
+    - ice: fix changing of ring descriptor size (ethtool -G)
+    - ice: update fw version check logic
+    - net: hns3: Fix for packet buffer setting bug
+    - Bluetooth: btbcm: Add entry for BCM4335C0 UART bluetooth
+    - Bluetooth: hci_qca: Remove hdev dereference in qca_close().
+    - x86: boot: Fix EFI stub alignment
+    - net: hns3: Add nic state check before calling netif_tx_wake_queue
+    - net: hns3: Fix ets validate issue
+    - pinctrl: sunxi: fix 'pctrl->functions' allocation in
+      sunxi_pinctrl_build_state
+    - pinctrl: qcom: spmi-mpp: Fix err handling of pmic_mpp_set_mux
+    - brcmfmac: fix for proper support of 160MHz bandwidth
+    - net: hns3: Check hdev state when getting link status
+    - net: hns3: Set STATE_DOWN bit of hdev state when stopping net
+    - net: phy: phylink: ensure the carrier is off when starting phylink
+    - block, bfq: correctly charge and reset entity service in all cases
+    - arm64: entry: Allow handling of undefined instructions from EL1
+    - kprobes: Return error if we fail to reuse kprobe instead of BUG_ON()
+    - spi: gpio: No MISO does not imply no RX
+    - ACPI / LPSS: Add alternative ACPI HIDs for Cherry Trail DMA controllers
+    - pinctrl: qcom: spmi-mpp: Fix drive strength setting
+    - bpf/verifier: fix verifier instability
+    - failover: Add missing check to validate 'slave_dev' in
+      net_failover_slave_unregister
+    - perf tests: Fix record+probe_libc_inet_pton.sh without ping's debuginfo
+    - pinctrl: spmi-mpp: Fix pmic_mpp_config_get() to be compliant
+    - pinctrl: ssbi-gpio: Fix pm8xxx_pin_config_get() to be compliant
+    - net: hns3: Preserve vlan 0 in hardware table
+    - net: hns3: Fix ping exited problem when doing lp selftest
+    - net: hns3: Fix for vf vlan delete failed problem
+    - net: dsa: mv88e6xxx: Fix writing to a PHY page.
+    - mt76x2u: run device cleanup routine if resume fails
+    - rsi: fix memory alignment issue in ARM32 platforms
+    - libertas_tf: prevent underflow in process_cmdrequest()
+    - iwlwifi: mvm: fix BAR seq ctrl reporting
+    - gpio: brcmstb: allow 0 width GPIO banks
+    - ixgbe: disallow IPsec Tx offload when in SR-IOV mode
+    - ixgbevf: VF2VF TCP RSS
+    - wil6210: fix RX buffers release and unmap
+    - ath10k: schedule hardware restart if WMI command times out
+    - libata: Apply NOLPM quirk for SAMSUNG MZ7TD256HAFV-000L9
+    - thermal: rcar_thermal: Prevent doing work after unbind
+    - thermal: da9062/61: Prevent hardware access during system suspend
+    - cifs: fix a credits leak for compund commands
+    - cgroup, netclassid: add a preemption point to write_classid
+    - net: stmmac: dwmac-sun8i: fix OF child-node lookup
+    - f2fs: fix to account IO correctly for cgroup writeback
+    - MD: Memory leak when flush bio size is zero
+    - md: fix memleak for mempool
+    - of: Add missing exports of node name compare functions
+    - scsi: esp_scsi: Track residual for PIO transfers
+    - scsi: ufs: Schedule clk gating work on correct queue
+    - UAPI: ndctl: Fix g++-unsupported initialisation in headers
+    - KVM: nVMX: Clear reserved bits of #DB exit qualification
+    - scsi: megaraid_sas: fix a missing-check bug
+    - RDMA/core: Do not expose unsupported counters
+    - RDMA/cm: Respect returned status of cm_init_av_by_path
+    - IB/ipoib: Clear IPCB before icmp_send
+    - RDMA/bnxt_re: Avoid accessing nq->bar_reg_iomem in failure case
+    - RDMA/bnxt_re: Fix recursive lock warning in debug kernel
+    - usb: host: ohci-at91: fix request of irq for optional gpio
+    - PCI: mediatek: Fix mtk_pcie_find_port() endpoint/port matching logic
+    - PCI: cadence: Use AXI region 0 to signal interrupts from EP
+    - usb: typec: tcpm: Report back negotiated PPS voltage and current
+    - tpm: suppress transmit cmd error logs when TPM 1.2 is disabled/deactivated
+    - f2fs: clear PageError on the read path
+    - Drivers: hv: vmbus: Use cpumask_var_t for on-stack cpu mask
+    - VMCI: Resource wildcard match fixed
+    - PCI / ACPI: Enable wake automatically for power managed bridges
+    - xprtrdma: Reset credit grant properly after a disconnect
+    - irqchip/pdc: Setup all edge interrupts as rising edge at GIC
+    - usb: dwc2: fix call to vbus supply exit routine, call it unlocked
+    - usb: dwc2: fix a race with external vbus supply
+    - usb: gadget: udc: atmel: handle at91sam9rl PMC
+    - ext4: fix argument checking in EXT4_IOC_MOVE_EXT
+    - MD: fix invalid stored role for a disk
+    - PCI: cadence: Correct probe behaviour when failing to get PHY
+    - nvmem: check the return value of nvmem_add_cells()
+    - xhci: Avoid USB autosuspend when resuming USB2 ports.
+    - scsi: qla2xxx: Fix recursive mailbox timeout
+    - f2fs: fix to recover inode's crtime during POR
+    - f2fs: fix to recover inode's i_flags during POR
+    - PCI/MSI: Warn and return error if driver enables MSI/MSI-X twice
+    - coresight: etb10: Fix handling of perf mode
+    - PCI: dwc: pci-dra7xx: Enable errata i870 for both EP and RC mode
+    - crypto: caam - fix implicit casts in endianness helpers
+    - usb: chipidea: Prevent unbalanced IRQ disable
+    - Smack: ptrace capability use fixes
+    - driver/dma/ioat: Call del_timer_sync() without holding prep_lock
+    - ASoC: AMD: Fix capture unstable in beginning for some runs
+    - firmware: coreboot: Unmap ioregion after device population
+    - IB/ipoib: Use dev_port to expose network interface port numbers
+    - IB/mlx5: Allow transition of DCI QP to reset
+    - uio: ensure class is registered before devices
+    - scsi: lpfc: Correct soft lockup when running mds diagnostics
+    - scsi: lpfc: Correct race with abort on completion path
+    - f2fs: avoid sleeping under spin_lock
+    - f2fs: report error if quota off error during umount
+    - signal: Always deliver the kernel's SIGKILL and SIGSTOP to a pid namespace
+      init
+    - f2fs: fix to flush all dirty inodes recovered in readonly fs
+    - mfd: menelaus: Fix possible race condition and leak
+    - dmaengine: dma-jz4780: Return error if not probed from DT
+    - IB/rxe: fix for duplicate request processing and ack psns
+    - ALSA: hda: Check the non-cached stream buffers more explicitly
+    - cpupower: Fix AMD Family 0x17 msr_pstate size
+    - Revert "f2fs: fix to clear PG_checked flag in set_page_dirty()"
+    - f2fs: fix missing up_read
+    - f2fs: fix to recover cold bit of inode block during POR
+    - f2fs: fix to account IO correctly
+    - OPP: Free OPP table properly on performance state irregularities
+    - ARM: dts: exynos: Convert exynos5250.dtsi to opp-v2 bindings
+    - ARM: dts: exynos: Mark 1 GHz CPU OPP as suspend OPP on Exynos5250
+    - xen-swiotlb: use actually allocated size on check physical continuous
+    - tpm: Restore functionality to xen vtpm driver.
+    - xen/blkfront: avoid NULL blkfront_info dereference on device removal
+    - xen/balloon: Support xend-based toolstack
+    - xen: fix race in xen_qlock_wait()
+    - xen: make xen_qlock_wait() nestable
+    - xen/pvh: increase early stack size
+    - xen/pvh: don't try to unplug emulated devices
+    - libertas: don't set URB_ZERO_PACKET on IN USB transfer
+    - usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
+    - usb: typec: tcpm: Fix APDO PPS order checking to be based on voltage
+    - usb: gadget: udc: renesas_usb3: Fix b-device mode for "workaround"
+    - mt76: mt76x2: fix multi-interface beacon configuration
+    - iwlwifi: mvm: check return value of rs_rate_from_ucode_rate()
+    - net/ipv4: defensive cipso option parsing
+    - dmaengine: ppc4xx: fix off-by-one build failure
+    - scsi: sched/wait: Add wait_event_lock_irq_timeout for TASK_UNINTERRUPTIBLE
+      usage
+    - scsi: target: Fix target_wait_for_sess_cmds breakage with active signals
+    - libnvdimm: Hold reference on parent while scheduling async init
+    - libnvdimm, region: Fail badblocks listing for inactive regions
+    - libnvdimm, pmem: Fix badblocks population for 'raw' namespaces
+    - ASoC: intel: skylake: Add missing break in skl_tplg_get_token()
+    - ASoC: sta32x: set ->component pointer in private struct
+    - IB/mlx5: Fix MR cache initialization
+    - IB/rxe: Revise the ib_wr_opcode enum
+    - jbd2: fix use after free in jbd2_log_do_checkpoint()
+    - gfs2_meta: ->mount() can get NULL dev_name
+    - ext4: fix EXT4_IOC_SWAP_BOOT
+    - ext4: initialize retries variable in ext4_da_write_inline_data_begin()
+    - ext4: fix setattr project check in fssetxattr ioctl
+    - ext4: propagate error from dquot_initialize() in EXT4_IOC_FSSETXATTR
+    - ext4: fix use-after-free race in ext4_remount()'s error path
+    - selinux: fix mounting of cgroup2 under older policies
+    - HID: wacom: Work around HID descriptor bug in DTK-2451 and DTH-2452
+    - HID: hiddev: fix potential Spectre v1
+    - EDAC, amd64: Add Family 17h, models 10h-2fh support
+    - EDAC, {i7core,sb,skx}_edac: Fix uncorrected error counting
+    - EDAC, skx_edac: Fix logical channel intermediate decoding
+    - ARM: dts: dra7: Fix up unaligned access setting for PCIe EP
+    - PCI/ASPM: Fix link_state teardown on device removal
+    - PCI: Add Device IDs for Intel GPU "spurious interrupt" quirk
+    - signal/GenWQE: Fix sending of SIGKILL
+    - signal: Guard against negative signal numbers in copy_siginfo_from_user32
+    - crypto: lrw - Fix out-of bounds access on counter overflow
+    - crypto: tcrypt - fix ghash-generic speed test
+    - crypto: aesni - don't use GFP_ATOMIC allocation if the request doesn't cross
+      a page in gcm
+    - crypto: morus/generic - fix for big endian systems
+    - crypto: aegis/generic - fix for big endian systems
+    - crypto: speck - remove Speck
+    - mm: /proc/pid/smaps_rollup: fix NULL pointer deref in smaps_pte_range()
+    - userfaultfd: disable irqs when taking the waitqueue lock
+    - ima: fix showing large 'violations' or 'runtime_measurements_count'
+    - ima: open a new file instance if no read permissions
+    - hugetlbfs: dirty pages as they are added to pagecache
+    - mm/rmap: map_pte() was not handling private ZONE_DEVICE page properly
+    - mm/hmm: fix race between hmm_mirror_unregister() and mmu_notifier callback
+    - KVM: arm/arm64: Ensure only THP is candidate for adjustment
+    - KVM: arm64: Fix caching of host MDCR_EL2 value
+    - kbuild: fix kernel/bounds.c 'W=1' warning
+    - iio: ad5064: Fix regulator handling
+    - iio: adc: imx25-gcq: Fix leak of device_node in mx25_gcq_setup_cfgs()
+    - iio: adc: at91: fix acking DRDY irq on simple conversions
+    - iio: adc: at91: fix wrong channel number in triggered buffer mode
+    - w1: omap-hdq: fix missing bus unregister at removal
+    - smb3: allow stats which track session and share reconnects to be reset
+    - smb3: do not attempt cifs operation in smb3 query info error path
+    - smb3: on kerberos mount if server doesn't specify auth type use krb5
+    - printk: Fix panic caused by passing log_buf_len to command line
+    - genirq: Fix race on spurious interrupt detection
+    - tpm: fix response size validation in tpm_get_random()
+    - NFC: nfcmrvl_uart: fix OF child-node lookup
+    - NFSv4.1: Fix the r/wsize checking
+    - nfs: Fix a missed page unlock after pg_doio()
+    - nfsd: correctly decrement odstate refcount in error path
+    - nfsd: Fix an Oops in free_session()
+    - lockd: fix access beyond unterminated strings in prints
+    - dm ioctl: harden copy_params()'s copy_from_user() from malicious users
+    - dm zoned: fix metadata block ref counting
+    - dm zoned: fix various dmz_get_mblock() issues
+    - media: ov7670: make "xclk" clock optional
+    - fsnotify: Fix busy inodes during unmount
+    - powerpc64/module elfv1: Set opd addresses after module relocation
+    - powerpc/msi: Fix compile error on mpc83xx
+    - powerpc/tm: Fix HFSCR bit for no suspend case
+    - powerpc/64s/hash: Do not use PPC_INVALIDATE_ERAT on CPUs before POWER9
+    - MIPS: OCTEON: fix out of bounds array access on CN68XX
+    - rtc: ds1307: fix ds1339 wakealarm support
+    - rtc: cmos: Fix non-ACPI undefined reference to `hpet_rtc_interrupt'
+    - rtc: cmos: Remove the `use_acpi_alarm' module parameter for !ACPI
+    - power: supply: twl4030-charger: fix OF sibling-node lookup
+    - ocxl: Fix access to the AFU Descriptor Data
+    - iommu/arm-smmu: Ensure that page-table updates are visible before TLBI
+    - TC: Set DMA masks for devices
+    - net: bcmgenet: fix OF child-node lookup
+    - media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
+    - Revert "media: dvbsky: use just one mutex for serializing device R/W ops"
+    - kgdboc: Passing ekgdboc to command line causes panic
+    - remoteproc: qcom: q6v5: Propagate EPROBE_DEFER
+    - media: cec: make cec_get_edid_spa_location() an inline function
+    - media: cec: integrate cec_validate_phys_addr() in cec-api.c
+    - xen: fix xen_qlock_wait()
+    - xen: remove size limit of privcmd-buf mapping interface
+    - xen-blkfront: fix kernel panic with negotiate_mq error path
+    - media: cec: add new tx/rx status bits to detect aborts/timeouts
+    - media: cec: fix the Signal Free Time calculation
+    - media: cec: forgot to cancel delayed work
+    - media: em28xx: use a default format if TRY_FMT fails
+    - media: tvp5150: avoid going past array on v4l2_querymenu()
+    - media: em28xx: fix input name for Terratec AV 350
+    - media: em28xx: make v4l2-compliance happier by starting sequence on zero
+    - media: em28xx: fix handler for vidioc_s_input()
+    - media: adv7604: when the EDID is cleared, unconfigure CEC as well
+    - media: adv7842: when the EDID is cleared, unconfigure CEC as well
+    - drm/mediatek: fix OF sibling-node lookup
+    - media: media colorspaces*.rst: rename AdobeRGB to opRGB
+    - media: replace ADOBERGB by OPRGB
+    - media: hdmi.h: rename ADOBE_RGB to OPRGB and ADOBE_YCC to OPYCC
+    - arm64: lse: remove -fcall-used-x0 flag
+    - rpmsg: smd: fix memory leak on channel create
+    - Cramfs: fix abad comparison when wrap-arounds occur
+    - ARM: dts: socfpga: Fix SDRAM node address for Arria10
+    - arm64: dts: stratix10: Correct System Manager register size
+    - soc: qcom: rmtfs-mem: Validate that scm is available
+    - soc/tegra: pmc: Fix child-node lookup
+    - selftests/ftrace: Fix synthetic event test to delete event correctly
+    - selftests/powerpc: Fix ptrace tm failure
+    - tracing: Return -ENOENT if there is no target synthetic event
+    - btrfs: qgroup: Avoid calling qgroup functions if qgroup is not enabled
+    - btrfs: Handle owner mismatch gracefully when walking up tree
+    - btrfs: locking: Add extra check in btrfs_init_new_buffer() to avoid deadlock
+    - btrfs: fix error handling in free_log_tree
+    - btrfs: fix error handling in btrfs_dev_replace_start
+    - btrfs: Enhance btrfs_trim_fs function to handle error better
+    - btrfs: Ensure btrfs_trim_fs can trim the whole filesystem
+    - btrfs: iterate all devices during trim, instead of fs_devices::alloc_list
+    - btrfs: don't attempt to trim devices that don't support it
+    - btrfs: keep trim from interfering with transaction commits
+    - btrfs: wait on caching when putting the bg cache
+    - Btrfs: don't clean dirty pages during buffered writes
+    - btrfs: release metadata before running delayed refs
+    - btrfs: protect space cache inode alloc with GFP_NOFS
+    - btrfs: reset max_extent_size on clear in a bitmap
+    - btrfs: make sure we create all new block groups
+    - Btrfs: fix warning when replaying log after fsync of a tmpfile
+    - Btrfs: fix wrong dentries after fsync of file that got its parent replaced
+    - btrfs: qgroup: Dirty all qgroups before rescan
+    - Btrfs: fix null pointer dereference on compressed write path error
+    - Btrfs: fix assertion on fsync of regular file when using no-holes feature
+    - Btrfs: fix deadlock when writing out free space caches
+    - btrfs: reset max_extent_size properly
+    - btrfs: set max_extent_size properly
+    - btrfs: don't use ctl->free_space for max_extent_size
+    - btrfs: only free reserved extent if we didn't insert it
+    - btrfs: fix insert_reserved error handling
+    - btrfs: don't run delayed_iputs in commit
+    - btrfs: move the dio_sem higher up the callchain
+    - Btrfs: fix use-after-free during inode eviction
+    - Btrfs: fix use-after-free when dumping free space
+    - net: sched: Remove TCA_OPTIONS from policy
+    - vt: fix broken display when running aptitude
+    - bpf: wait for running BPF programs when updating map-in-map
+    - vga_switcheroo: Fix missing gpu_bound call at audio client registration
+    - MD: fix invalid stored role for a disk - try2
+    - Linux 4.19.2
+
+  * [FEAT] Guest-dedicated Crypto Adapters (LP: #1787405)
+    - KVM: s390: vsie: simulate VCPU SIE entry/exit
+    - KVM: s390: introduce and use KVM_REQ_VSIE_RESTART
+    - KVM: s390: refactor crypto initialization
+    - s390: vfio-ap: base implementation of VFIO AP device driver
+    - s390: vfio-ap: register matrix device with VFIO mdev framework
+    - s390: vfio-ap: sysfs interfaces to configure adapters
+    - s390: vfio-ap: sysfs interfaces to configure domains
+    - s390: vfio-ap: sysfs interfaces to configure control domains
+    - s390: vfio-ap: sysfs interface to view matrix mdev matrix
+    - KVM: s390: interface to clear CRYCB masks
+    - s390: vfio-ap: implement mediated device open callback
+    - s390: vfio-ap: implement VFIO_DEVICE_GET_INFO ioctl
+    - s390: vfio-ap: zeroize the AP queues
+    - s390: vfio-ap: implement VFIO_DEVICE_RESET ioctl
+    - KVM: s390: Clear Crypto Control Block when using vSIE
+    - KVM: s390: vsie: Do the CRYCB validation first
+    - KVM: s390: vsie: Make use of CRYCB FORMAT2 clear
+    - KVM: s390: vsie: Allow CRYCB FORMAT-2
+    - KVM: s390: vsie: allow CRYCB FORMAT-1
+    - KVM: s390: vsie: allow CRYCB FORMAT-0
+    - KVM: s390: vsie: allow guest FORMAT-0 CRYCB on host FORMAT-1
+    - KVM: s390: vsie: allow guest FORMAT-1 CRYCB on host FORMAT-2
+    - KVM: s390: vsie: allow guest FORMAT-0 CRYCB on host FORMAT-2
+    - KVM: s390: device attrs to enable/disable AP interpretation
+    - KVM: s390: CPU model support for AP virtualization
+    - s390: doc: detailed specifications for AP virtualization
+    - KVM: s390: fix locking for crypto setting error path
+    - KVM: s390: Tracing APCB changes
+    - s390: vfio-ap: setup APCB mask using KVM dedicated function
+    - [Config:] Enable CONFIG_S390_AP_IOMMU and set CONFIG_VFIO_AP to module.
+
+  * Bypass of mount visibility through userns + mount propagation (LP: #1789161)
+    - mount: Retest MNT_LOCKED in do_umount
+    - mount: Don't allow copying MNT_UNBINDABLE|MNT_LOCKED mounts
+
+  *  CVE-2018-18955: nested user namespaces with more than five extents
+    incorrectly grant privileges over inode (LP: #1801924) // CVE-2018-18955
+    - userns: also map extents in the reverse map to kernel IDs
+
+  * kdump fail due to an IRQ storm (LP: #1797990)
+    - SAUCE: x86/PCI: Export find_cap() to be used in early PCI code
+    - SAUCE: x86/quirks: Add parameter to clear MSIs early on boot
+    - SAUCE: x86/quirks: Scan all busses for early PCI quirks
+
+  * Disable LPM for Raydium Touchscreens (LP: #1802248)
+    - USB: quirks: Add no-lpm quirk for Raydium touchscreens
+
+  * Power consumption during s2idle is higher than long idle(sk hynix)
+    (LP: #1801875)
+    - SAUCE: pci: prevent sk hynix nvme from entering D3
+    - SAUCE: nvme: add quirk to not call disable function when suspending
+
+  * Disco update: v4.19.1 upstream stable release (LP: #1801739)
+    - bridge: do not add port to router list when receives query with source
+      0.0.0.0
+    - ipv6/ndisc: Preserve IPv6 control buffer if protocol error handlers are
+      called
+    - net/mlx5e: fix csum adjustments caused by RXFCS
+    - net: sched: gred: pass the right attribute to gred_change_table_def()
+    - net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
+    - net: udp: fix handling of CHECKSUM_COMPLETE packets
+    - Revert "net: simplify sock_poll_wait"
+    - rtnetlink: Disallow FDB configuration for non-Ethernet device
+    - vhost: Fix Spectre V1 vulnerability
+    - bonding: fix length of actor system
+    - openvswitch: Fix push/pop ethernet validation
+    - net/ipv6: Allow onlink routes to have a device mismatch if it is the default
+      route
+    - net/smc: fix smc_buf_unuse to use the lgr pointer
+    - mlxsw: spectrum_switchdev: Don't ignore deletions of learned MACs
+    - mlxsw: core: Fix devlink unregister flow
+    - net: drop skb on failure in ip_check_defrag()
+    - net: Properly unlink GRO packets on overflow.
+    - r8169: fix broken Wake-on-LAN from S5 (poweroff)
+    - Revert "be2net: remove desc field from be_eq_obj"
+    - sctp: check policy more carefully when getting pr status
+    - sparc64: Export __node_distance.
+    - sparc64: Make corrupted user stacks more debuggable.
+    - sparc64: Wire up compat getpeername and getsockname.
+    - net: bridge: remove ipv6 zero address check in mcast queries
+    - Linux 4.19.1
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.7.11-1ubuntu1, zfs to 0.7.11-3ubuntu1
+    - [Config] updateconfigs after 4.19.2 stable update
+    - [Config] Disable unneded options for s390
+    - [Config] Update annotations for 4.19
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 15 Nov 2018 09:55:37 -0800
+
+linux (4.19.0-4.5) disco; urgency=medium
+
+  * Add checksum offload and TSO support for HiNIC adapters (LP: #1800664)
+    - net-next/hinic: add checksum offload and TSO support
+
+  * [Bionic][Cosmic] Fix to ipmi to support vendor specific messages greater
+    than 255 bytes (LP: #1799794)
+    - ipmi:ssif: Add support for multi-part transmit messages > 2 parts
+
+  * Packaging resync (LP: #1786013)
+    - [Package] add support for specifying the primary makefile
+
+  * Update ENA driver to version 2.0.1K (LP: #1798182)
+    - net: ena: minor performance improvement
+    - net: ena: complete host info to match latest ENA spec
+    - net: ena: introduce Low Latency Queues data structures according to ENA spec
+    - net: ena: add functions for handling Low Latency Queues in ena_com
+    - net: ena: add functions for handling Low Latency Queues in ena_netdev
+    - net: ena: use CSUM_CHECKED device indication to report skb's checksum status
+    - net: ena: explicit casting and initialization, and clearer error handling
+    - net: ena: limit refill Rx threshold to 256 to avoid latency issues
+    - net: ena: change rx copybreak default to reduce kernel memory pressure
+    - net: ena: remove redundant parameter in ena_com_admin_init()
+    - net: ena: update driver version to 2.0.1
+    - net: ena: fix indentations in ena_defs for better readability
+    - net: ena: Fix Kconfig dependency on X86
+    - net: ena: enable Low Latency Queues
+    - net: ena: fix compilation error in xtensa architecture
+
+  * [Bionic][Cosmic]  ipmi: Fix timer race with module unload (LP: #1799281)
+    - ipmi: Fix timer race with module unload
+
+  * Overlayfs in user namespace leaks directory content of inaccessible
+    directories (LP: #1793458) // CVE-2018-6559
+    - SAUCE: overlayfs: ensure mounter privileges when reading directories
+
+  * not able to unwind the stack from within __kernel_clock_gettime in the Linux
+    vDSO (LP: #1797963)
+    - powerpc/vdso: Correct call frame information
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Don't print secure boot state
+      from the efi stub"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Make get_cert_list() use
+      efi_status_to_str() to print error messages."
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err()."
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Make get_cert_list() not complain
+      about cert lists that aren't present."
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) MODSIGN: Allow the "db" UEFI variable
+      to be suppressed"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI
+      Secure Boot"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Add an EFI signature blob parser"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Add EFI signature data types"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) KEYS: Allow unrestricted boot-time
+      addition of keys to secondary keyring"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in
+      secure boot mode"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to
+      indicate secure boot mode"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Copy secure_boot flag in boot params
+      across kexec reboot"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Lock down perf"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) bpf: Restrict kernel image access
+      functions when the kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Lock down kprobes"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Lock down /proc/kcore"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the
+      testmmiotrace module"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Lock down module params that specify
+      hardware parameters (eg. ioport)"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Lock down TIOCSSERIAL"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) acpi: Disable APEI error injection if
+      the kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) acpi: Disable ACPI table override if
+      the kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param
+      when the kernel has been locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) ACPI: Limit access to custom_method
+      when the kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) x86: Lock down IO port access when the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) PCI: Lock down BAR access when the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is
+      locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) hibernate: Disable when the kernel is
+      locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Enforce module signatures if the
+      kernel is locked down"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Add a SysRq option to lift kernel
+      lockdown"
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) Add the ability to lock down access to
+      the running kernel image"
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Lock down module params that specify hardware
+      parameters (eg. ioport)
+    - SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the testmmiotrace module
+    - SAUCE: (efi-lockdown) Lock down /proc/kcore
+    - SAUCE: (efi-lockdown) Lock down kprobes
+    - SAUCE: (efi-lockdown) Lock down perf
+    - SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) KEYS: Allow unrestricted boot-time addition of keys to
+      secondary keyring
+    - SAUCE: (efi-lockdown) efi: Add EFI signature data types
+    - SAUCE: (efi-lockdown) efi: Add an EFI signature blob parser
+    - SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI Secure Boot
+    - SAUCE: (efi-lockdown) MODSIGN: Allow the "db" UEFI variable to be suppressed
+    - SAUCE: (efi-lockdown) Make get_cert_list() not complain about cert lists
+      that aren't present.
+    - SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err().
+    - SAUCE: (efi-lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) efi/x86: Call efi_parse_options() from efi_main()
+    - SAUCE: (efi-lockdown) Fix for module sig verification
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) module: remove support for having IMA validate modules
+    - [Packaging] generate Vcs-Git url from changelog
+    - [Config] CONFIG_SCSI_MQ_DEFAULT=y
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 02 Nov 2018 14:22:55 -0500
+
+linux (4.19.0-3.4) cosmic; urgency=medium
+
+  * Support Edge Gateway's Bluetooth LED (LP: #1798332)
+    - SAUCE: Bluetooth: Support for LED on Edge Gateways
+
+  * Support Edge Gateway's WIFI LED (LP: #1798330)
+    - SAUCE: mwifiex: Switch WiFi LED state according to the device status
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.19
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 22 Oct 2018 09:13:39 -0500
+
+linux (4.19.0-2.3) cosmic; urgency=medium
+
+  * fscache: bad refcounting in fscache_op_complete leads to OOPS (LP: #1797314)
+    - SAUCE: fscache: Fix race in decrementing refcount of op->npages
+
+  * Provide mode where all vCPUs on a core must be the same VM (LP: #1792957)
+    - KVM: PPC: Book3S HV: Provide mode where all vCPUs on a core must be the same
+      VM
+
+  * The front MIC can't work on the Lenovo M715 (LP: #1797292)
+    - ALSA: hda/realtek - Fix the problem of the front MIC on the Lenovo M715
+
+  * arm64: snapdragon: WARNING: CPU: 0 PID: 1 at drivers/irqchip/irq-gic.c:1016
+    gic_irq_domain_translate (LP: #1797143)
+    - SAUCE: arm64: dts: msm8916: camms: fix gic_irq_domain_translate warnings
+
+  * Dell new AIO requires a new uart backlight driver (LP: #1727235)
+    - SAUCE: platform/x86: dell-uart-backlight: new backlight driver for DELL AIO
+    - updateconfigs for Dell UART backlight driver
+
+  * Please make CONFIG_PWM_LPSS_PCI and CONFIG_PWM_LPSS_PLATFORM built in to
+    make brightness adjustment working on various BayTrail/CherryTrail-based
+    devices (LP: #1783964)
+    - [Config]: Make PWM_LPSS_* built-in
+
+  * check and fix zkey required kernel modules locations in debs, udebs, and
+    initramfs (LP: #1794346)
+    - [Config] add s390 crypto modules to crypt-modules udeb
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_VBOXGUEST=n
+    - ubuntu: vbox -- update to 5.2.18-dfsg-2
+    - ubuntu: enable vbox build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.19-rc8
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 15 Oct 2018 10:52:04 -0500
+
+linux (4.19.0-1.2) cosmic; urgency=medium
+
+  * Page leaking in cachefiles_read_backing_file while vmscan is active
+    (LP: #1793430)
+    - SAUCE: cachefiles: Page leaking in cachefiles_read_backing_file while vmscan
+      is active
+
+  * SRU: Enable middle button of touchpad on ThinkPad P72 (LP: #1793463)
+    - Input: elantech - enable middle button of touchpad on ThinkPad P72
+
+  * Improvements to the kernel source package preparation (LP: #1793461)
+    - [Packaging] startnewrelease: add support for backport kernels
+
+  * Fix unusable NVIDIA GPU after S3 (LP: #1793338)
+    - SAUCE: PCI: Reprogram bridge prefetch registers on resume
+
+  * Error reported when creating ZFS pool with "-t" option, despite successful
+    pool creation (LP: #1769937)
+    - SAUCE: (noup) Update zfs to 0.7.9-3ubuntu6
+
+  * device hotplug of vfio devices can lead to deadlock in vfio_pci_release
+    (LP: #1792099)
+    - SAUCE: vfio -- release device lock before userspace requests
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] retpoline -- fix temporary filenaming
+    - CONFIG_BCH_CONST_PARAMS=n
+    - Packaging: final-checks: remove trailing backport suffix
+    - SAUCE: import aufs driver
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.19-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 25 Sep 2018 16:32:24 -0500
+
+linux (4.19.0-0.1) cosmic; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - ubuntu -- disable vbox build
+    - Disable zfs build
+    - SAUCE: Import aufs driver
+    - Update dropped.txt
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.19-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 13 Sep 2018 07:54:47 -0500
+
+linux (4.19.0-0.0) cosmic; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 13 Sep 2018 06:44:09 -0500
+
+linux (4.18.0-8.9) cosmic; urgency=medium
+
+  * linux: 4.18.0-8.9 -proposed tracker (LP: #1791663)
+
+  * Cosmic update to v4.18.7 stable release (LP: #1791660)
+    - rcu: Make expedited GPs handle CPU 0 being offline
+    - net: 6lowpan: fix reserved space for single frames
+    - net: mac802154: tx: expand tailroom if necessary
+    - 9p/net: Fix zero-copy path in the 9p virtio transport
+    - spi: davinci: fix a NULL pointer dereference
+    - spi: pxa2xx: Add support for Intel Ice Lake
+    - spi: spi-fsl-dspi: Fix imprecise abort on VF500 during probe
+    - spi: cadence: Change usleep_range() to udelay(), for atomic context
+    - mmc: block: Fix unsupported parallel dispatch of requests
+    - mmc: renesas_sdhi_internal_dmac: mask DMAC interrupts
+    - mmc: renesas_sdhi_internal_dmac: fix #define RST_RESERVED_BITS
+    - readahead: stricter check for bdi io_pages
+    - block: fix infinite loop if the device loses discard capability
+    - block: blk_init_allocated_queue() set q->fq as NULL in the fail case
+    - block: really disable runtime-pm for blk-mq
+    - blkcg: Introduce blkg_root_lookup()
+    - block: Introduce blk_exit_queue()
+    - block: Ensure that a request queue is dissociated from the cgroup controller
+    - apparmor: fix bad debug check in apparmor_secid_to_secctx()
+    - dma-buf: Move BUG_ON from _add_shared_fence to _add_shared_inplace
+    - libertas: fix suspend and resume for SDIO connected cards
+    - media: Revert "[media] tvp5150: fix pad format frame height"
+    - mailbox: xgene-slimpro: Fix potential NULL pointer dereference
+    - Replace magic for trusting the secondary keyring with #define
+    - Fix kexec forbidding kernels signed with keys in the secondary keyring to
+      boot
+    - powerpc/fadump: handle crash memory ranges array index overflow
+    - powerpc/64s: Fix page table fragment refcount race vs speculative references
+    - powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
+    - powerpc/pkeys: Give all threads control of their key permissions
+    - powerpc/pkeys: Deny read/write/execute by default
+    - powerpc/pkeys: key allocation/deallocation must not change pkey registers
+    - powerpc/pkeys: Save the pkey registers before fork
+    - powerpc/pkeys: Fix calculation of total pkeys.
+    - powerpc/pkeys: Preallocate execute-only key
+    - powerpc/nohash: fix pte_access_permitted()
+    - powerpc64/ftrace: Include ftrace.h needed for enable/disable calls
+    - powerpc/powernv/pci: Work around races in PCI bridge enabling
+    - cxl: Fix wrong comparison in cxl_adapter_context_get()
+    - IB/mlx5: Honor cnt_set_id_valid flag instead of set_id
+    - IB/mlx5: Fix leaking stack memory to userspace
+    - IB/srpt: Fix srpt_cm_req_recv() error path (1/2)
+    - IB/srpt: Fix srpt_cm_req_recv() error path (2/2)
+    - IB/srpt: Support HCAs with more than two ports
+    - overflow.h: Add arithmetic shift helper
+    - RDMA/mlx5: Fix shift overflow in mlx5_ib_create_wq
+    - ib_srpt: Fix a use-after-free in srpt_close_ch()
+    - ib_srpt: Fix a use-after-free in __srpt_close_all_ch()
+    - RDMA/rxe: Set wqe->status correctly if an unexpected response is received
+    - 9p: fix multiple NULL-pointer-dereferences
+    - fs/9p/xattr.c: catch the error of p9_client_clunk when setting xattr failed
+    - 9p/virtio: fix off-by-one error in sg list bounds check
+    - net/9p/client.c: version pointer uninitialized
+    - net/9p/trans_fd.c: fix race-condition by flushing workqueue before the
+      kfree()
+    - dm integrity: change 'suspending' variable from bool to int
+    - dm thin: stop no_space_timeout worker when switching to write-mode
+    - dm cache metadata: save in-core policy_hint_size to on-disk superblock
+    - dm cache metadata: set dirty on all cache blocks after a crash
+    - dm crypt: don't decrease device limits
+    - dm writecache: fix a crash due to reading past end of dirty_bitmap
+    - uart: fix race between uart_put_char() and uart_shutdown()
+    - Drivers: hv: vmbus: Fix the offer_in_progress in vmbus_process_offer()
+    - Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
+    - iio: sca3000: Fix missing return in switch
+    - iio: ad9523: Fix displayed phase
+    - iio: ad9523: Fix return value for ad952x_store()
+    - extcon: Release locking when sending the notification of connector state
+    - eventpoll.h: wrap casts in () properly
+    - vmw_balloon: fix inflation of 64-bit GFNs
+    - vmw_balloon: do not use 2MB without batching
+    - vmw_balloon: VMCI_DOORBELL_SET does not check status
+    - vmw_balloon: fix VMCI use when balloon built into kernel
+    - rtc: omap: fix resource leak in registration error path
+    - rtc: omap: fix potential crash on power off
+    - tracing: Do not call start/stop() functions when tracing_on does not change
+    - tracing/blktrace: Fix to allow setting same value
+    - printk/tracing: Do not trace printk_nmi_enter()
+    - livepatch: Validate module/old func name length
+    - uprobes: Use synchronize_rcu() not synchronize_sched()
+    - mfd: hi655x: Fix regmap area declared size for hi655x
+    - ovl: fix wrong use of impure dir cache in ovl_iterate()
+    - ACPICA: AML Parser: skip opcodes that open a scope upon parse failure
+    - ACPICA: Clear status of all events when entering sleep states
+    - drivers/block/zram/zram_drv.c: fix bug storing backing_dev
+    - sched: idle: Avoid retaining the tick when it has been stopped
+    - cpuidle: menu: Handle stopped tick more aggressively
+    - cpufreq: governor: Avoid accessing invalid governor_data
+    - PM / sleep: wakeup: Fix build error caused by missing SRCU support
+    - ALSA: ac97: fix device initialization in the compat layer
+    - ALSA: ac97: fix check of pm_runtime_get_sync failure
+    - ALSA: ac97: fix unbalanced pm_runtime_enable
+    - i2c: designware: Re-init controllers with pm_disabled set on resume
+    - KVM: VMX: fixes for vmentry_l1d_flush module parameter
+    - KVM: PPC: Book3S: Fix guest DMA when guest partially backed by THP pages
+    - xtensa: limit offsets in __loop_cache_{all,page}
+    - xtensa: increase ranges in ___invalidate_{i,d}cache_all
+    - block, bfq: return nbytes and not zero from struct cftype .write() method
+    - pnfs/blocklayout: off by one in bl_map_stripe()
+    - nfsd: fix leaked file lock with nfs exported overlayfs
+    - NFSv4 client live hangs after live data migration recovery
+    - NFSv4: Fix locking in pnfs_generic_recover_commit_reqs
+    - NFSv4: Fix a sleep in atomic context in nfs4_callback_sequence()
+    - ARM: tegra: Fix Tegra30 Cardhu PCA954x reset
+    - ARM: dts: am57xx-idk: Enable dual role for USB2 port
+    - pwm: omap-dmtimer: Return -EPROBE_DEFER if no dmtimer platform data
+    - mm/tlb: Remove tlb_remove_table() non-concurrent condition
+    - iommu/ipmmu-vmsa: Don't register as BUS IOMMU if machine doesn't have IPMMU-
+      VMSA
+    - iommu/vt-d: Add definitions for PFSID
+    - iommu/vt-d: Fix dev iotlb pfsid use
+    - sys: don't hold uts_sem while accessing userspace memory
+    - userns: move user access out of the mutex
+    - ubifs: Fix memory leak in lprobs self-check
+    - Revert "UBIFS: Fix potential integer overflow in allocation"
+    - ubifs: Check data node size before truncate
+    - ubifs: xattr: Don't operate on deleted inodes
+    - ubifs: Fix directory size calculation for symlinks
+    - ubifs: Fix synced_i_size calculation for xattr inodes
+    - pwm: tiehrpwm: Don't use emulation mode bits to control PWM output
+    - pwm: tiehrpwm: Fix disabling of output of PWMs
+    - fb: fix lost console when the user unplugs a USB adapter
+    - udlfb: fix semaphore value leak
+    - udlfb: fix display corruption of the last line
+    - udlfb: don't switch if we are switching to the same videomode
+    - udlfb: set optimal write delay
+    - udlfb: make a local copy of fb_ops
+    - udlfb: handle allocation failure
+    - udlfb: set line_length in dlfb_ops_set_par
+    - getxattr: use correct xattr length
+    - libnvdimm: Use max contiguous area for namespace size
+    - libnvdimm: fix ars_status output length calculation
+    - bcache: release dc->writeback_lock properly in bch_writeback_thread()
+    - kconfig: fix "Can't open ..." in parallel build
+    - perf auxtrace: Fix queue resize
+    - crypto: vmx - Fix sleep-in-atomic bugs
+    - crypto: aesni - Use unaligned loads from gcm_context_data
+    - crypto: arm64/sm4-ce - check for the right CPU feature bit
+    - crypto: caam - fix DMA mapping direction for RSA forms 2 & 3
+    - crypto: caam/jr - fix descriptor DMA unmapping
+    - crypto: caam/qi - fix error path in xts setkey
+    - fs/quota: Fix spectre gadget in do_quotactl
+    - udf: Fix mounting of Win7 created UDF filesystems
+    - cpuidle: menu: Retain tick when shallow state is selected
+    - arm64: mm: always enable CONFIG_HOLES_IN_ZONE
+    - Linux 4.18.7
+
+  * CVE-2017-5715
+    - s390: detect etoken facility
+    - KVM: s390: add etoken support for guests
+
+  * Missing Intel GPU pci-id's (LP: #1789924)
+    - drm/i915/whl: Introducing Whiskey Lake platform
+    - drm/i915/aml: Introducing Amber Lake platform
+    - drm/i915/cfl: Add a new CFL PCI ID.
+
+  * [18.10 FEAT] Add kernel config options for SMC-R/D (LP: #1789934)
+    - s390/ism: add device driver for internal shared memory
+    - CONFIG_ISM=y for s390
+
+  * Cosmic update to v4.18.6 stable release (LP: #1791105)
+    - PATCH scripts/kernel-doc
+    - scripts/kernel-doc: Escape all literal braces in regexes
+    - scsi: libsas: dynamically allocate and free ata host
+    - xprtrdma: Fix disconnect regression
+    - mei: don't update offset in write
+    - cifs: add missing support for ACLs in SMB 3.11
+    - CIFS: fix uninitialized ptr deref in smb2 signing
+    - cifs: add missing debug entries for kconfig options
+    - cifs: use a refcount to protect open/closing the cached file handle
+    - cifs: check kmalloc before use
+    - smb3: enumerating snapshots was leaving part of the data off end
+    - smb3: Do not send SMB3 SET_INFO if nothing changed
+    - smb3: don't request leases in symlink creation and query
+    - smb3: fill in statfs fsid and correct namelen
+    - btrfs: use correct compare function of dirty_metadata_bytes
+    - btrfs: don't leak ret from do_chunk_alloc
+    - Btrfs: fix mount failure after fsync due to hard link recreation
+    - Btrfs: fix btrfs_write_inode vs delayed iput deadlock
+    - Btrfs: fix send failure when root has deleted files still open
+    - Btrfs: send, fix incorrect file layout after hole punching beyond eof
+    - hwmon: (k10temp) 27C Offset needed for Threadripper2
+    - bpf, arm32: fix stack var offset in jit
+    - regulator: arizona-ldo1: Use correct device to get enable GPIO
+    - iommu/arm-smmu: Error out only if not enough context interrupts
+    - printk: Split the code for storing a message into the log buffer
+    - printk: Create helper function to queue deferred console handling
+    - printk/nmi: Prevent deadlock when accessing the main log buffer in NMI
+    - kprobes/arm64: Fix %p uses in error messages
+    - arm64: Fix mismatched cache line size detection
+    - arm64: Handle mismatched cache type
+    - arm64: mm: check for upper PAGE_SHIFT bits in pfn_valid()
+    - arm64: dts: rockchip: corrected uart1 clock-names for rk3328
+    - KVM: arm/arm64: Fix potential loss of ptimer interrupts
+    - KVM: arm/arm64: Fix lost IRQs from emulated physcial timer when blocked
+    - KVM: arm/arm64: Skip updating PMD entry if no change
+    - KVM: arm/arm64: Skip updating PTE entry if no change
+    - s390/kvm: fix deadlock when killed by oom
+    - perf kvm: Fix subcommands on s390
+    - stop_machine: Reflow cpu_stop_queue_two_works()
+    - stop_machine: Atomically queue and wake stopper threads
+    - ext4: check for NUL characters in extended attribute's name
+    - ext4: use ext4_warning() for sb_getblk failure
+    - ext4: sysfs: print ext4_super_block fields as little-endian
+    - ext4: reset error code in ext4_find_entry in fallback
+    - ext4: fix race when setting the bitmap corrupted flag
+    - x86/gpu: reserve ICL's graphics stolen memory
+    - platform/x86: wmi: Do not mix pages and kmalloc
+    - platform/x86: ideapad-laptop: Apply no_hw_rfkill to Y20-15IKBM, too
+    - mm: move tlb_table_flush to tlb_flush_mmu_free
+    - mm/tlb, x86/mm: Support invalidating TLB caches for RCU_TABLE_FREE
+    - x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
+    - x86/speculation/l1tf: Fix off-by-one error when warning that system has too
+      much RAM
+    - x86/speculation/l1tf: Suggest what to do on systems with too much RAM
+    - x86/vdso: Fix vDSO build if a retpoline is emitted
+    - x86/process: Re-export start_thread()
+    - KVM: x86: ensure all MSRs can always be KVM_GET/SET_MSR'd
+    - KVM: x86: SVM: Call x86_spec_ctrl_set_guest/host() with interrupts disabled
+    - fuse: Don't access pipe->buffers without pipe_lock()
+    - fuse: fix initial parallel dirops
+    - fuse: fix double request_end()
+    - fuse: fix unlocked access to processing queue
+    - fuse: umount should wait for all requests
+    - fuse: Fix oops at process_init_reply()
+    - fuse: Add missed unlock_page() to fuse_readpages_fill()
+    - lib/vsprintf: Do not handle %pO[^F] as %px
+    - udl-kms: change down_interruptible to down
+    - udl-kms: handle allocation failure
+    - udl-kms: fix crash due to uninitialized memory
+    - udl-kms: avoid division
+    - b43legacy/leds: Ensure NUL-termination of LED name string
+    - b43/leds: Ensure NUL-termination of LED name string
+    - ASoC: dpcm: don't merge format from invalid codec dai
+    - ASoC: zte: Fix incorrect PCM format bit usages
+    - ASoC: sirf: Fix potential NULL pointer dereference
+    - ASoC: wm_adsp: Correct DSP pointer for preloader control
+    - soc: qcom: rmtfs-mem: fix memleak in probe error paths
+    - pinctrl: freescale: off by one in imx1_pinconf_group_dbg_show()
+    - scsi: qla2xxx: Fix stalled relogin
+    - x86/vdso: Fix lsl operand order
+    - x86/nmi: Fix NMI uaccess race against CR3 switching
+    - x86/irqflags: Mark native_restore_fl extern inline
+    - x86/spectre: Add missing family 6 check to microcode check
+    - x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
+    - hwmon: (nct6775) Fix potential Spectre v1
+    - x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
+    - x86: Allow generating user-space headers without a compiler
+    - s390/mm: fix addressing exception after suspend/resume
+    - s390/lib: use expoline for all bcr instructions
+    - s390: fix br_r1_trampoline for machines without exrl
+    - s390/qdio: reset old sbal_state flags
+    - s390/numa: move initial setup of node_to_cpumask_map
+    - s390/purgatory: Fix crash with expoline enabled
+    - s390/purgatory: Add missing FORCE to Makefile targets
+    - kprobes: Show blacklist addresses as same as kallsyms does
+    - kprobes: Replace %p with other pointer types
+    - kprobes/arm: Fix %p uses in error messages
+    - kprobes: Make list and blacklist root user read only
+    - MIPS: Correct the 64-bit DSP accumulator register size
+    - MIPS: memset.S: Fix byte_fixup for MIPSr6
+    - MIPS: Always use -march=<arch>, not -<arch> shortcuts
+    - MIPS: Change definition of cpu_relax() for Loongson-3
+    - MIPS: lib: Provide MIPS64r6 __multi3() for GCC < 7
+    - tpm: Return the actual size when receiving an unsupported command
+    - tpm: separate cmd_ready/go_idle from runtime_pm
+    - scsi: mpt3sas: Fix calltrace observed while running IO & reset
+    - scsi: mpt3sas: Fix _transport_smp_handler() error path
+    - scsi: sysfs: Introduce sysfs_{un,}break_active_protection()
+    - scsi: core: Avoid that SCSI device removal through sysfs triggers a deadlock
+    - iscsi target: fix session creation failure handling
+    - mtd: rawnand: hynix: Use ->exec_op() in hynix_nand_reg_write_op()
+    - mtd: rawnand: fsmc: Stop using chip->read_buf()
+    - mtd: rawnand: marvell: add suspend and resume hooks
+    - mtd: rawnand: qcom: wait for desc completion in all BAM channels
+    - clk: rockchip: fix clk_i2sout parent selection bits on rk3399
+    - clk: npcm7xx: fix memory allocation
+    - PM / clk: signedness bug in of_pm_clk_add_clks()
+    - power: generic-adc-battery: fix out-of-bounds write when copying channel
+      properties
+    - power: generic-adc-battery: check for duplicate properties copied from iio
+      channels
+    - watchdog: Mark watchdog touch functions as notrace
+    - cdrom: Fix info leak/OOB read in cdrom_ioctl_drive_status
+    - x86/dumpstack: Don't dump kernel memory based on usermode RIP
+    - Linux 4.18.6
+    - updateconfigs after v4.18.6 stable update
+
+  * random oopses on s390 systems using NVMe devices (LP: #1790480)
+    - s390/pci: fix out of bounds access during irq setup
+
+  * [18.10 FEAT] zcrypt DD: introduce APQN tags to support deterministic driver
+    binding (LP: #1784331)
+    - s390/zcrypt: code beautify
+    - s390/zcrypt: AP bus support for alternate driver(s)
+    - s390/zcrypt: hex string mask improvements for apmask and aqmask.
+
+  * performance drop with ATS enabled (LP: #1788097)
+    - powerpc/powernv: Fix concurrency issue with npu->mmio_atsd_usage
+
+  * Fix MCE handling for user access of poisoned device-dax mapping
+    (LP: #1774366)
+    - device-dax: Convert to vmf_insert_mixed and vm_fault_t
+    - device-dax: Enable page_mapping()
+    - device-dax: Set page->index
+    - filesystem-dax: Set page->index
+    - mm, madvise_inject_error: Disable MADV_SOFT_OFFLINE for ZONE_DEVICE pages
+    - mm, dev_pagemap: Do not clear ->mapping on final put
+    - mm, madvise_inject_error: Let memory_failure() optionally take a page
+      reference
+    - mm, memory_failure: Collect mapping size in collect_procs()
+    - filesystem-dax: Introduce dax_lock_mapping_entry()
+    - mm, memory_failure: Teach memory_failure() about dev_pagemap pages
+    - x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses
+    - x86/memory_failure: Introduce {set, clear}_mce_nospec()
+    - libnvdimm, pmem: Restore page attributes when clearing errors
+
+  * Reconcile hns3 SAUCE patches with upstream (LP: #1787477)
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix comments for
+      hclge_get_ring_chain_from_mbx"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix for using wrong mask and
+      shift in hclge_get_ring_chain_from_mbx"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix for reset_level default
+      assignment probelm"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove unnecessary ring
+      configuration operation while resetting"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix return value error in
+      hns3_reset_notify_down_enet"
+    - Revert "UBUNTU: SAUCE: net: hns3: Fix for phy link issue when using marvell
+      phy driver"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: separate roce from nic when
+      resetting"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: correct reset event status
+      register"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: prevent to request reset
+      frequently"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: reset net device with rtnl_lock"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: modify the order of initializeing
+      command queue register"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: prevent sending command during
+      global or core reset"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: Use roce handle when calling roce
+      callback function"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove the warning when clear
+      reset cause"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix get_vector ops in
+      hclgevf_main module"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix warning bug when doing lp
+      selftest"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: Add configure for mac minimal
+      frame size"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix for mailbox message truncated
+      problem"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix for l4 checksum offload bug"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix for waterline not setting
+      correctly"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix for mac pause not disable in
+      pfc mode"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix tc setup when netdev is first
+      up"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: Add calling roce callback
+      function when link status change"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: optimize the process of notifying
+      roce client"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: Add pf reset for hip08 RoCE"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: Add SPDX tags to hns3 driver"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove unused struct member and
+      definition"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix mislead parameter name"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: modify inconsistent bit mask
+      macros"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: use decimal for bit offset
+      macros"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: fix unreasonable code comments"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove extra space and brackets"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: standardize the handle of return
+      value"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove some redundant
+      assignments"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: modify hnae_ to hnae3_"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: use dma_zalloc_coherent instead
+      of kzalloc/dma_map_single"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: give default option while
+      dependency HNS3 set"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove some unused members of
+      some structures"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove a redundant
+      hclge_cmd_csq_done"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: using modulo for cyclic counters
+      in hclge_cmd_send"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: simplify hclge_cmd_csq_clean"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove some redundant
+      assignments"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove useless code in
+      hclge_cmd_send"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove unused
+      hclge_ring_to_dma_dir"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: use lower_32_bits and
+      upper_32_bits"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove back in struct hclge_hw"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: add unlikely for error check"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove the Redundant put_vector
+      in hns3_client_uninit"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: print the ret value in error
+      information"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: extraction an interface for state
+      state init|uninit"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove unused head file in
+      hnae3.c"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: add l4_type check for both ipv4
+      and ipv6"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: add vector status check before
+      free vector"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: rename the interface for
+      init_client_instance and uninit_client_instance"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: remove hclge_get_vector_index
+      from hclge_bind_ring_with_vector"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: RX BD information valid only in
+      last BD except VLD bit and buffer size"
+    - Revert "UBUNTU: SAUCE: {topost} net: hns3: add support for serdes loopback
+      selftest"
+    - net: hns3: Updates RX packet info fetch in case of multi BD
+    - net: hns3: remove hclge_get_vector_index from hclge_bind_ring_with_vector
+    - net: hns3: rename the interface for init_client_instance and
+      uninit_client_instance
+    - net: hns3: add vector status check before free vector
+    - net: hns3: add l4_type check for both ipv4 and ipv6
+    - net: hns3: add unlikely for error check
+    - net: hns3: remove unused head file in hnae3.c
+    - net: hns3: extraction an interface for state init|uninit
+    - net: hns3: print the ret value in error information
+    - net: hns3: remove the Redundant put_vector in hns3_client_uninit
+    - net: hns3: remove back in struct hclge_hw
+    - net: hns3: use lower_32_bits and upper_32_bits
+    - net: hns3: remove unused hclge_ring_to_dma_dir
+    - net: hns3: remove useless code in hclge_cmd_send
+    - net: hns3: remove some redundant assignments
+    - net: hns3: simplify hclge_cmd_csq_clean
+    - net: hns3: remove a redundant hclge_cmd_csq_done
+    - net: hns3: remove some unused members of some structures
+    - net: hns3: give default option while dependency HNS3 set
+    - net: hns3: use dma_zalloc_coherent instead of kzalloc/dma_map_single
+    - net: hns3: modify hnae_ to hnae3_
+    - net: hns3: Fix tc setup when netdev is first up
+    - net: hns3: Fix for mac pause not disable in pfc mode
+    - net: hns3: Fix for waterline not setting correctly
+    - net: hns3: Fix for l4 checksum offload bug
+    - net: hns3: Fix for mailbox message truncated problem
+    - net: hns3: Add configure for mac minimal frame size
+    - net: hns3: Fix warning bug when doing lp selftest
+    - net: hns3: Fix get_vector ops in hclgevf_main module
+    - net: hns3: Remove the warning when clear reset cause
+    - net: hns3: Prevent sending command during global or core reset
+    - net: hns3: Modify the order of initializing command queue register
+    - net: hns3: Reset net device with rtnl_lock
+    - net: hns3: Prevent to request reset frequently
+    - net: hns3: Correct reset event status register
+    - net: hns3: Fix return value error in hns3_reset_notify_down_enet
+    - net: hns3: remove unnecessary ring configuration operation while resetting
+    - net: hns3: Fix for reset_level default assignment probelm
+    - net: hns3: Fix for using wrong mask and shift in
+      hclge_get_ring_chain_from_mbx
+    - net: hns3: Fix comments for hclge_get_ring_chain_from_mbx
+    - net: hns3: Remove some redundant assignments
+    - net: hns3: Standardize the handle of return value
+    - net: hns3: Remove extra space and brackets
+    - net: hns3: Correct unreasonable code comments
+    - net: hns3: Use decimal for bit offset macros
+    - net: hns3: Modify inconsistent bit mask macros
+    - net: hns3: Fix misleading parameter name
+    - net: hns3: Remove unused struct member and definition
+    - net: hns3: Add SPDX tags to HNS3 PF driver
+    - net: hns3: Add support for serdes loopback selftest
+    - net: hns3: Fix for phy link issue when using marvell phy driver
+
+  * [Regression] kernel crashdump fails on arm64 (LP: #1786878)
+    - arm64: export memblock_reserve()d regions via /proc/iomem
+    - drivers: acpi: add dependency of EFI for arm64
+    - efi/arm: preserve early mapping of UEFI memory map longer for BGRT
+    - efi/arm: map UEFI memory map even w/o runtime services enabled
+    - arm64: acpi: fix alignment fault in accessing ACPI
+    - [Config] CONFIG_ARCH_SUPPORTS_ACPI=y
+    - arm64: fix ACPI dependencies
+    - ACPI: fix menuconfig presentation of ACPI submenu
+
+  * TB 16 issue on Dell Lattitude 7490 with large amount of data (LP: #1785780)
+    - r8152: disable RX aggregation on new Dell TB16 dock
+
+  * Support Power Management for Thunderbolt Controller  (LP: #1789358)
+    - thunderbolt: Use 64-bit DMA mask if supported by the platform
+    - thunderbolt: Do not unnecessarily call ICM get route
+    - thunderbolt: No need to take tb->lock in domain suspend/complete
+    - thunderbolt: Use correct ICM commands in system suspend
+    - thunderbolt: Add support for runtime PM
+
+  * Enable AMD PCIe MP2 for AMDI0011 (LP: #1773940)
+    - SAUCE: i2c:amd I2C Driver based on PCI Interface for upcoming platform
+    - SAUCE: i2c:amd move out pointer in union i2c_event_base
+    - SAUCE: i2c:amd Depends on ACPI
+    - [Config] i2c: CONFIG_I2C_AMD_MP2=y on x86
+
+  * Microphone cannot be detected with front panel audio combo jack on HP Z8-G4
+    machine (LP: #1789145)
+    - ALSA: hda/realtek - Fix HP Headset Mic can't record
+
+  * Please enable CONFIG_PAGE_POISONING (LP: #1783651)
+    - [Config] Enable CONFIG_PAGE_POISONING configs
+
+  * Tango platform uses __initcall without further checks (LP: #1787945)
+    - [Config] disable ARCH_TANGO
+
+  * [18.10 FEAT] SMC-Direct (LP: #1786902)
+    - net/smc: determine port attributes independent from pnet table
+    - net/smc: add pnetid support
+    - net/smc: add base infrastructure for SMC-D and ISM
+    - net/smc: add pnetid support for SMC-D and ISM
+    - net/smc: add SMC-D support in CLC messages
+    - net/smc: add SMC-D support in data transfer
+    - net/smc: add SMC-D support in af_smc
+    - net/smc: add SMC-D diag support
+    - net/smc: provide smc mode in smc_diag.c
+    - net/smc: eliminate cursor read and write calls
+    - net/smc: add function to get link group from link
+    - net/smc: use DECLARE_BITMAP for rtokens_used_mask
+    - net/smc: remove local variable page in smc_rx_splice()
+    - net/smc: Remove a WARN_ON() statement
+    - net/smc: Simplify ib_post_(send|recv|srq_recv)() calls
+    - net/smc: fewer parameters for smc_llc_send_confirm_link()
+    - net/smc: use correct vlan gid of RoCE device
+    - net/smc: provide fallback reason code
+    - net/smc: improve delete link processing
+    - net: simplify sock_poll_wait
+    - net/smc: send response to test link signal
+
+  * Miscellaneous Ubuntu changes
+    - [Config] update annotations for CONFIG_CRYPTO_SPECK_NEON
+    - [Config] fix up annotatios for CONFIG_CRYPTO_SPECK
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 10 Sep 2018 07:08:38 -0500
+
+linux (4.18.0-7.8) cosmic; urgency=medium
+
+  * linux: 4.18.0-7.8 -proposed tracker (LP: #1789459)
+
+  * pmtu.sh fails on 4.18 kernel (LP: #1789436)
+    - SAUCE: Revert "vti6: fix PMTU caching and reporting on xmit"
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 28 Aug 2018 11:08:51 -0500
+
+linux (4.18.0-6.7) cosmic; urgency=medium
+
+  * linux: 4.18.0-6.7 -proposed tracker (LP: #1788881)
+
+  * systemd 237-3ubuntu10 ADT test failure with linux 4.18.0-5.6 (LP: #1787440)
+    - Config: Disable BPF_JIT_ALWAYS_ON on i386
+
+  * execveat03 in ubuntu_ltp_syscalls failed on X/B (LP: #1786729)
+    - cap_inode_getsecurity: use d_find_any_alias() instead of d_find_alias()
+
+  * Cosmic update to v4.18.5 stable release (LP: #1788874)
+    - EDAC: Add missing MEM_LRDDR4 entry in edac_mem_types[]
+    - pty: fix O_CLOEXEC for TIOCGPTPEER
+    - mm: Allow non-direct-map arguments to free_reserved_area()
+    - x86/mm/init: Pass unconverted symbol addresses to free_init_pages()
+    - x86/mm/init: Add helper for freeing kernel image pages
+    - x86/mm/init: Remove freed kernel image areas from alias mapping
+    - powerpc64s: Show ori31 availability in spectre_v1 sysfs file not v2
+    - ext4: fix spectre gadget in ext4_mb_regular_allocator()
+    - drm/i915/kvmgt: Fix potential Spectre v1
+    - drm/amdgpu/pm: Fix potential Spectre v1
+    - parisc: Remove unnecessary barriers from spinlock.h
+    - parisc: Remove ordered stores from syscall.S
+    - PCI: Restore resized BAR state on resume
+    - PCI / ACPI / PM: Resume all bridges on suspend-to-RAM
+    - PCI: hotplug: Don't leak pci_slot on registration failure
+    - PCI: aardvark: Size bridges before resources allocation
+    - PCI: Skip MPS logic for Virtual Functions (VFs)
+    - PCI: pciehp: Fix use-after-free on unplug
+    - PCI: pciehp: Fix unprotected list iteration in IRQ handler
+    - i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
+    - i2c: imx: Fix race condition in dma read
+    - reiserfs: fix broken xattr handling (heap corruption, bad retval)
+    - Linux 4.18.5
+
+  * [18.10 FEAT] Add kernel config option "CONFIG_SCLP_OFB" (LP: #1787898)
+    - [Config] CONFIG_SCLP_OFB=y for s390x
+
+  * errors when scanning partition table of corrupted AIX disk (LP: #1787281)
+    - partitions/aix: fix usage of uninitialized lv_info and lvname structures
+    - partitions/aix: append null character to print data from disk
+
+  * Apply NVMe bugfix from Google that bjf asked for (LP: #1787635)
+    - nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
+
+  * ThinkPad systems have no HDMI sound when using the nvidia GPU (LP: #1787058)
+    - ACPI / OSI: Add OEM _OSI string to enable NVidia HDMI audio
+
+  * Cosmic update to v4.18.4 stable release (LP: #1788454)
+    - l2tp: use sk_dst_check() to avoid race on sk->sk_dst_cache
+    - net_sched: fix NULL pointer dereference when delete tcindex filter
+    - net_sched: Fix missing res info when create new tc_index filter
+    - r8169: don't use MSI-X on RTL8168g
+    - ALSA: hda - Sleep for 10ms after entering D3 on Conexant codecs
+    - ALSA: hda - Turn CX8200 into D3 as well upon reboot
+    - ALSA: vx222: Fix invalid endian conversions
+    - ALSA: virmidi: Fix too long output trigger loop
+    - ALSA: cs5535audio: Fix invalid endian conversion
+    - ALSA: dice: fix wrong copy to rx parameters for Alesis iO26
+    - ALSA: hda: Correct Asrock B85M-ITX power_save blacklist entry
+    - ALSA: memalloc: Don't exceed over the requested size
+    - ALSA: vxpocket: Fix invalid endian conversions
+    - ALSA: seq: Fix poll() error return
+    - media: gl861: fix probe of dvb_usb_gl861
+    - USB: serial: sierra: fix potential deadlock at close
+    - USB: serial: pl2303: add a new device id for ATEN
+    - USB: option: add support for DW5821e
+    - ACPI / PM: save NVS memory for ASUS 1025C laptop
+    - tty: serial: 8250: Revert NXP SC16C2552 workaround
+    - serial: 8250_exar: Read INT0 from slave device, too
+    - serial: 8250_dw: always set baud rate in dw8250_set_termios
+    - serial: 8250_dw: Add ACPI support for uart on Broadcom SoC
+    - uio: fix wrong return value from uio_mmap()
+    - misc: sram: fix resource leaks in probe error path
+    - Revert "uio: use request_threaded_irq instead"
+    - Bluetooth: avoid killing an already killed socket
+    - isdn: Disable IIOCDBGVAR
+    - net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
+    - hv/netvsc: Fix NULL dereference at single queue mode fallback
+    - r8169: don't use MSI-X on RTL8106e
+    - ip_vti: fix a null pointer deferrence when create vti fallback tunnel
+    - net: ethernet: mvneta: Fix napi structure mixup on armada 3700
+    - net: mvneta: fix mvneta_config_rss on armada 3700
+    - cls_matchall: fix tcf_unbind_filter missing
+    - Linux 4.18.4
+
+  * Cosmic update to v4.18.3 stable release (LP: #1788453)
+    - x86/speculation/l1tf: Exempt zeroed PTEs from inversion
+    - Linux 4.18.3
+
+  * Cosmic update to v4.18.2 stable release (LP: #1788452)
+    - x86/l1tf: Fix build error seen if CONFIG_KVM_INTEL is disabled
+    - x86: i8259: Add missing include file
+    - x86/hyper-v: Check for VP_INVAL in hyperv_flush_tlb_others()
+    - x86/platform/UV: Mark memblock related init code and data correctly
+    - x86/mm/pti: Clear Global bit more aggressively
+    - xen/pv: Call get_cpu_address_sizes to set x86_virt/phys_bits
+    - x86/mm: Disable ioremap free page handling on x86-PAE
+    - kbuild: verify that $DEPMOD is installed
+    - crypto: ccree - fix finup
+    - crypto: ccree - fix iv handling
+    - crypto: ccp - Check for NULL PSP pointer at module unload
+    - crypto: ccp - Fix command completion detection race
+    - crypto: x86/sha256-mb - fix digest copy in sha256_mb_mgr_get_comp_job_avx2()
+    - crypto: vmac - require a block cipher with 128-bit block size
+    - crypto: vmac - separate tfm and request context
+    - crypto: blkcipher - fix crash flushing dcache in error path
+    - crypto: ablkcipher - fix crash flushing dcache in error path
+    - crypto: skcipher - fix aligning block size in skcipher_copy_iv()
+    - crypto: skcipher - fix crash flushing dcache in error path
+    - ioremap: Update pgtable free interfaces with addr
+    - x86/mm: Add TLB purge to free pmd/pte page interfaces
+    - Linux 4.18.2
+
+  * Cosmic update to v4.18.2 stable release (LP: #1788452) // CVE-2018-9363
+    - Bluetooth: hidp: buffer overflow in hidp_process_report
+
+  * linux-cloud-tools-common: Ensure hv-kvp-daemon.service starts before
+    walinuxagent.service (LP: #1739107)
+    - [Debian] hyper-v -- Ensure that hv-kvp-daemon.service starts before
+      walinuxagent.service
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: ipvs: remove nbsp characters from Kconfig
+    - [Config] CONFIG_MPROFILE_KERNEL=y for ppc64el
+    - [Config] CONFIG_DRM_RCAR_LVDS=m for snapdragon
+    - [Config] CONFIG_MDIO_MSCC_MIIM=n for s390x
+    - [Config] CONFIG_NET_VENDOR_MICROSEMI=n, CONFIG_NET_VENDOR_NI=n for s390x
+    - [Config] update annotations following config review
+    - [Debian] set CROSS_COMPILE when generating kernel configs
+    - [Config] Disable the Speck cipher
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 24 Aug 2018 14:18:15 -0500
+
+linux (4.18.0-5.6) cosmic; urgency=medium
+
+  * Cosmic update to v4.18.1 stable release (LP: #1787264)
+    - x86/paravirt: Fix spectre-v2 mitigations for paravirt guests
+    - x86/speculation: Protect against userspace-userspace spectreRSB
+    - kprobes/x86: Fix %p uses in error messages
+    - x86/irqflags: Provide a declaration for native_save_fl
+    - x86/speculation/l1tf: Increase 32bit PAE __PHYSICAL_PAGE_SHIFT
+    - x86/speculation/l1tf: Change order of offset/type in swap entry
+    - x86/speculation/l1tf: Protect swap entries against L1TF
+    - x86/speculation/l1tf: Protect PROT_NONE PTEs against speculation
+    - x86/speculation/l1tf: Make sure the first page is always reserved
+    - x86/speculation/l1tf: Add sysfs reporting for l1tf
+    - x86/speculation/l1tf: Disallow non privileged high MMIO PROT_NONE mappings
+    - x86/speculation/l1tf: Limit swap file size to MAX_PA/2
+    - x86/bugs: Move the l1tf function and define pr_fmt properly
+    - sched/smt: Update sched_smt_present at runtime
+    - x86/smp: Provide topology_is_primary_thread()
+    - x86/topology: Provide topology_smt_supported()
+    - cpu/hotplug: Make bringup/teardown of smp threads symmetric
+    - cpu/hotplug: Split do_cpu_down()
+    - cpu/hotplug: Provide knobs to control SMT
+    - x86/cpu: Remove the pointless CPU printout
+    - x86/cpu/AMD: Remove the pointless detect_ht() call
+    - x86/cpu/common: Provide detect_ht_early()
+    - x86/cpu/topology: Provide detect_extended_topology_early()
+    - x86/cpu/intel: Evaluate smp_num_siblings early
+    - x86/CPU/AMD: Do not check CPUID max ext level before parsing SMP info
+    - x86/cpu/AMD: Evaluate smp_num_siblings early
+    - x86/apic: Ignore secondary threads if nosmt=force
+    - x86/speculation/l1tf: Extend 64bit swap file size limit
+    - x86/cpufeatures: Add detection of L1D cache flush support.
+    - x86/CPU/AMD: Move TOPOEXT reenablement before reading smp_num_siblings
+    - x86/speculation/l1tf: Protect PAE swap entries against L1TF
+    - x86/speculation/l1tf: Fix up pte->pfn conversion for PAE
+    - Revert "x86/apic: Ignore secondary threads if nosmt=force"
+    - cpu/hotplug: Boot HT siblings at least once
+    - x86/KVM: Warn user if KVM is loaded SMT and L1TF CPU bug being present
+    - x86/KVM/VMX: Add module argument for L1TF mitigation
+    - x86/KVM/VMX: Add L1D flush algorithm
+    - x86/KVM/VMX: Add L1D MSR based flush
+    - x86/KVM/VMX: Add L1D flush logic
+    - x86/KVM/VMX: Split the VMX MSR LOAD structures to have an host/guest numbers
+    - x86/KVM/VMX: Add find_msr() helper function
+    - x86/KVM/VMX: Separate the VMX AUTOLOAD guest/host number accounting
+    - x86/KVM/VMX: Extend add_atomic_switch_msr() to allow VMENTER only MSRs
+    - x86/KVM/VMX: Use MSR save list for IA32_FLUSH_CMD if required
+    - cpu/hotplug: Online siblings when SMT control is turned on
+    - x86/litf: Introduce vmx status variable
+    - x86/kvm: Drop L1TF MSR list approach
+    - x86/l1tf: Handle EPT disabled state proper
+    - x86/kvm: Move l1tf setup function
+    - x86/kvm: Add static key for flush always
+    - x86/kvm: Serialize L1D flush parameter setter
+    - x86/kvm: Allow runtime control of L1D flush
+    - cpu/hotplug: Expose SMT control init function
+    - cpu/hotplug: Set CPU_SMT_NOT_SUPPORTED early
+    - x86/bugs, kvm: Introduce boot-time control of L1TF mitigations
+    - Documentation: Add section about CPU vulnerabilities
+    - x86/speculation/l1tf: Unbreak !__HAVE_ARCH_PFN_MODIFY_ALLOWED architectures
+    - x86/KVM/VMX: Initialize the vmx_l1d_flush_pages' content
+    - Documentation/l1tf: Fix typos
+    - cpu/hotplug: detect SMT disabled by BIOS
+    - x86/KVM/VMX: Don't set l1tf_flush_l1d to true from vmx_l1d_flush()
+    - x86/KVM/VMX: Replace 'vmx_l1d_flush_always' with 'vmx_l1d_flush_cond'
+    - x86/KVM/VMX: Move the l1tf_flush_l1d test to vmx_l1d_flush()
+    - x86/irq: Demote irq_cpustat_t::__softirq_pending to u16
+    - x86/KVM/VMX: Introduce per-host-cpu analogue of l1tf_flush_l1d
+    - x86: Don't include linux/irq.h from asm/hardirq.h
+    - x86/irq: Let interrupt handlers set kvm_cpu_l1tf_flush_l1d
+    - x86/KVM/VMX: Don't set l1tf_flush_l1d from vmx_handle_external_intr()
+    - Documentation/l1tf: Remove Yonah processors from not vulnerable list
+    - x86/speculation: Simplify sysfs report of VMX L1TF vulnerability
+    - x86/speculation: Use ARCH_CAPABILITIES to skip L1D flush on vmentry
+    - KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry
+    - cpu/hotplug: Fix SMT supported evaluation
+    - x86/speculation/l1tf: Invert all not present mappings
+    - x86/speculation/l1tf: Make pmd/pud_mknotpresent() invert
+    - x86/mm/pat: Make set_memory_np() L1TF safe
+    - x86/mm/kmmio: Make the tracer robust against L1TF
+    - tools headers: Synchronise x86 cpufeatures.h for L1TF additions
+    - x86/microcode: Allow late microcode loading with SMT disabled
+    - x86/smp: fix non-SMP broken build due to redefinition of
+      apic_id_is_primary_thread
+    - cpu/hotplug: Non-SMP machines do not make use of booted_once
+    - x86/init: fix build with CONFIG_SWAP=n
+    - Linux 4.18.1
+    - [Config] updateconfigs after v4.18.1 stable update
+
+  * Consider enabling CONFIG_NETWORK_PHY_TIMESTAMPING (LP: #1785816)
+    - [Config] Enable timestamping in network PHY devices
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_SYSCTL_SYSCALL=n
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.18
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 15 Aug 2018 14:20:59 -0500
+
+linux (4.18.0-4.5) cosmic; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.18-rc8
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 06 Aug 2018 13:54:02 -0500
+
+linux (4.18.0-3.4) cosmic; urgency=medium
+
+  * Suspend fails in Ubuntu and Kubuntu 18.04 but works fine in Ubuntu and
+    Kubuntu 17.10 (and on Kubuntu 18.04 using kernel 4.14.47) (LP: #1774950)
+    - ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation
+
+  * hinic interfaces aren't getting predictable names (LP: #1783138)
+    - hinic: Link the logical network device to the pci device in sysfs
+
+  * libvirtd is unable to configure bridge devices inside of LXD containers
+    (LP: #1784501)
+    - kernfs: allow creating kernfs objects with arbitrary uid/gid
+    - sysfs, kobject: allow creating kobject belonging to arbitrary users
+    - kobject: kset_create_and_add() - fetch ownership info from parent
+    - driver core: set up ownership of class devices in sysfs
+    - net-sysfs: require net admin in the init ns for setting tx_maxrate
+    - net-sysfs: make sure objects belong to container's owner
+    - net: create reusable function for getting ownership info of sysfs inodes
+    - bridge: make sure objects belong to container's owner
+    - sysfs: Fix regression when adding a file to an existing group
+
+  * locking sockets broken due to missing AppArmor socket mediation patches
+    (LP: #1780227)
+    - UBUNTU SAUCE: apparmor: fix apparmor mediating locking non-fs, unix sockets
+
+  * Update2 for ocxl driver (LP: #1781436)
+    - ocxl: Fix page fault handler in case of fault on dying process
+
+  * HDMI/DP audio can't work on the laptop of Dell Latitude 5495 (LP: #1782689)
+    - ALSA: hda: use PCI_BASE_CLASS_DISPLAY to replace PCI_CLASS_DISPLAY_VGA
+    - vga_switcheroo: set audio client id according to bound GPU id
+
+  * Allow Raven Ridge's audio controller to be runtime suspended (LP: #1782540)
+    - ALSA: hda: Add AZX_DCAPS_PM_RUNTIME for AMD Raven Ridge
+
+  * Invoking obsolete 'firmware_install' target breaks snap build (LP: #1782166)
+    - snapcraft.yaml: stop invoking the obsolete (and non-existing)
+      'firmware_install' target
+
+  * snapcraft.yaml: missing ubuntu-retpoline-extract-one script breaks the build
+    (LP: #1782116)
+    - snapcraft.yaml: copy retpoline-extract-one to scripts before build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.18-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 01 Aug 2018 08:49:40 -0500
+
+linux (4.18.0-2.3) cosmic; urgency=medium
+
+  * Kernel error "task zfs:pid blocked for more than 120 seconds" (LP: #1781364)
+    - SAUCE: (noup) zfs to 0.7.9-3ubuntu4
+
+  * [Regression] EXT4-fs error (device sda1): ext4_validate_inode_bitmap:99:
+    comm stress-ng: Corrupt inode bitmap (LP: #1780137)
+    - SAUCE: ext4: fix ext4_validate_inode_bitmap: comm stress-ng: Corrupt inode
+      bitmap
+
+  * Cloud-init causes potentially huge boot delays with 4.15 kernels
+    (LP: #1780062)
+    - random: Make getrandom() ready earlier
+
+  * hisi_sas_v3_hw: internal task abort: timeout and not done. (LP: #1777736)
+    - scsi: hisi_sas: Update a couple of register settings for v3 hw
+
+  * hisi_sas: Add missing PHY spinlock init (LP: #1777734)
+    - scsi: hisi_sas: Add missing PHY spinlock init
+
+  * hisi_sas: improve read performance by pre-allocating slot DMA buffers
+    (LP: #1777727)
+    - scsi: hisi_sas: Use dmam_alloc_coherent()
+    - scsi: hisi_sas: Pre-allocate slot DMA buffers
+
+  * hisi_sas: Failures during host reset (LP: #1777696)
+    - scsi: hisi_sas: Only process broadcast change in phy_bcast_v3_hw()
+    - scsi: hisi_sas: Fix the conflict between dev gone and host reset
+    - scsi: hisi_sas: Adjust task reject period during host reset
+    - scsi: hisi_sas: Add a flag to filter PHY events during reset
+    - scsi: hisi_sas: Release all remaining resources in clear nexus ha
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.7.9-3ubuntu2, zfs to 0.7.9-3ubuntu3
+    - SAUCE: mm: Fix exports that inadvertently make put_page() EXPORT_SYMBOL_GPL
+    - Enable zfs build
+    - SAUCE: Import aufs driver
+    - Revert "UBUNTU: [Config]: set CONFIG_EDAC_DEBUG=y for ARM64"
+    - [Config] retpoline -- review and accept retpoline changes
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.18-rc5
+  * Rebase to v4.18-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 24 Jul 2018 08:41:22 -0500
+
+linux (4.18.0-1.2) cosmic; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.18-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 09 Jul 2018 07:36:31 -0500
+
+linux (4.18.0-0.1) cosmic; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - ubuntu -- disable vbox build
+    - Disable zfs build
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) Add a SysRq option to lift kernel lockdown
+    - SAUCE: (efi-lockdown) ima: require secure_boot rules in lockdown mode
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/{mem,kmem,port} when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) kexec_load: Disable at runtime if the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86/msr: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Lock down module params that specify hardware
+      parameters (eg. ioport)
+    - SAUCE: (efi-lockdown) x86/mmiotrace: Lock down the testmmiotrace module
+    - SAUCE: (efi-lockdown) Lock down /proc/kcore
+    - SAUCE: (efi-lockdown) Lock down kprobes
+    - SAUCE: (efi-lockdown) bpf: Restrict kernel image access functions when the
+      kernel is locked down
+    - SAUCE: (efi-lockdown) Lock down perf
+    - SAUCE: (efi-lockdown) debugfs: Restrict debugfs when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) KEYS: Allow unrestricted boot-time addition of keys to
+      secondary keyring
+    - SAUCE: (efi-lockdown) efi: Add EFI signature data types
+    - SAUCE: (efi-lockdown) efi: Add an EFI signature blob parser
+    - SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI Secure Boot
+    - SAUCE: (efi-lockdown) MODSIGN: Allow the "db" UEFI variable to be suppressed
+    - SAUCE: (efi-lockdown) Make get_cert_list() not complain about cert lists
+      that aren't present.
+    - SAUCE: (efi-lockdown) Add efi_status_to_str() and rework
+      efi_status_to_err().
+    - SAUCE: (efi-lockdown) Make get_cert_list() use efi_status_to_str() to print
+      error messages.
+    - SAUCE: (efi-lockdown) lockdown: fix coordination of kernel module signature
+      verification
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) efi: Don't print secure boot state from the efi stub
+    - SAUCE: (namespace) block_dev: Support checking inode permissions in
+      lookup_bdev()
+    - SAUCE: (namespace) block_dev: Check permissions towards block device inode
+      when mounting
+    - SAUCE: (namespace) mtd: Check permissions towards mtd block device inode
+      when mounting
+    - SAUCE: (namespace) ext4: Add support for unprivileged mounts from user
+      namespaces
+    - SAUCE: (namespace) ext4: Add module parameter to enable user namespace
+      mounts
+    - SAUCE: (namespace) block_dev: Forbid unprivileged mounting when device is
+      opened for writing
+    - SAUCE: Import aufs driver
+    - Update dropped.txt
+    - [Config] updateconfigs after 4.18-rc3 rebase
+    - SAUCE: (no-up): ASoC: Intel: bytcr-rt5660: Remove snd_soc_codec use for 4.18
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.18-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 06 Jul 2018 10:46:37 -0500
+
+linux (4.18.0-0.0) cosmic; urgency=medium
+
+  * Dummy entry.
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 03 Jul 2018 11:10:33 -0500
+
+linux (4.17.0-4.5) cosmic; urgency=medium
+
+  * linux: 4.17.0-4.5 -proposed tracker (LP: #1779399)
+
+  * Update to ocxl driver for 18.04.1 (LP: #1775786)
+    - powerpc: Add TIDR CPU feature for POWER9
+    - powerpc: Use TIDR CPU feature to control TIDR allocation
+    - powerpc: use task_pid_nr() for TID allocation
+    - ocxl: Rename pnv_ocxl_spa_remove_pe to clarify it's action
+    - ocxl: Expose the thread_id needed for wait on POWER9
+    - ocxl: Add an IOCTL so userspace knows what OCXL features are available
+    - ocxl: Document new OCXL IOCTLs
+    - ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
+
+  * Please include ax88179_178a and r8152 modules in d-i udeb (LP: #1771823)
+    - [Config:] d-i: Add ax88179_178a and r8152 to nic-modules
+
+  * glibc pkeys test fail on powerpc (LP: #1776967)
+    - [Config] Temporarily disable CONFIG_PPC_MEM_KEYS
+
+  * After update to 4.13-43 Intel Graphics are Laggy (LP: #1773520)
+    - Revert "drm/i915/edp: Allow alternate fixed mode for eDP if available."
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.7.9-3ubuntu1, zfs to 0.7.9-3ubuntu1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 29 Jun 2018 13:37:52 -0500
+
+linux (4.17.0-3.4) cosmic; urgency=medium
+
+  * linux: 4.17.0-3.4 -proposed tracker (LP: #1779124)
+
+  * Cosmic update to v4.17.3 stable release (LP: #1778997)
+    - net: aquantia: fix unsigned numvecs comparison with less than zero
+    - bonding: re-evaluate force_primary when the primary slave name changes
+    - cdc_ncm: avoid padding beyond end of skb
+    - ipv6: allow PMTU exceptions to local routes
+    - net: dsa: add error handling for pskb_trim_rcsum
+    - net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620
+    - net/sched: act_simple: fix parsing of TCA_DEF_DATA
+    - tcp: verify the checksum of the first data segment in a new connection
+    - tls: fix use-after-free in tls_push_record
+    - tls: fix waitall behavior in tls_sw_recvmsg
+    - socket: close race condition between sock_close() and sockfs_setattr()
+    - udp: fix rx queue len reported by diag and proc interface
+    - net: in virtio_net_hdr only add VLAN_HLEN to csum_start if payload holds
+      vlan
+    - hv_netvsc: Fix a network regression after ifdown/ifup
+    - ACPICA: AML parser: attempt to continue loading table after error
+    - ext4: fix hole length detection in ext4_ind_map_blocks()
+    - ext4: update mtime in ext4_punch_hole even if no blocks are released
+    - ext4: do not allow external inodes for inline data
+    - ext4: bubble errors from ext4_find_inline_data_nolock() up to ext4_iget()
+    - ext4: correctly handle a zero-length xattr with a non-zero e_value_offs
+    - ext4: fix fencepost error in check for inode count overflow during resize
+    - driver core: Don't ignore class_dir_create_and_add() failure.
+    - Btrfs: allow empty subvol= again
+    - Btrfs: fix clone vs chattr NODATASUM race
+    - Btrfs: fix memory and mount leak in btrfs_ioctl_rm_dev_v2()
+    - btrfs: return error value if create_io_em failed in cow_file_range
+    - btrfs: scrub: Don't use inode pages for device replace
+    - ALSA: usb-audio: Disable the quirk for Nura headset
+    - ALSA: hda/conexant - Add fixup for HP Z2 G4 workstation
+    - ALSA: hda - Handle kzalloc() failure in snd_hda_attach_pcm_stream()
+    - ALSA: hda: add dock and led support for HP EliteBook 830 G5
+    - ALSA: hda: add dock and led support for HP ProBook 640 G4
+    - x86/MCE: Fix stack out-of-bounds write in mce-inject.c: Flags_read()
+    - smb3: fix various xid leaks
+    - smb3: on reconnect set PreviousSessionId field
+    - CIFS: 511c54a2f69195b28afb9dd119f03787b1625bb4 adds a check for session
+      expiry
+    - cifs: For SMB2 security informaion query, check for minimum sized security
+      descriptor instead of sizeof FileAllInformation class
+    - nbd: fix nbd device deletion
+    - nbd: update size when connected
+    - nbd: use bd_set_size when updating disk size
+    - blk-mq: reinit q->tag_set_list entry only after grace period
+    - bdi: Move cgroup bdi_writeback to a dedicated low concurrency workqueue
+    - cpufreq: Fix new policy initialization during limits updates via sysfs
+    - cpufreq: ti-cpufreq: Fix an incorrect error return value
+    - cpufreq: governors: Fix long idle detection logic in load calculation
+    - libata: zpodd: small read overflow in eject_tray()
+    - libata: Drop SanDisk SD7UB3Q*G1001 NOLPM quirk
+    - nvme/pci: Sync controller reset for AER slot_reset
+    - w1: mxc_w1: Enable clock before calling clk_get_rate() on it
+    - x86/vector: Fix the args of vector_alloc tracepoint
+    - x86/apic/vector: Prevent hlist corruption and leaks
+    - x86/apic: Provide apic_ack_irq()
+    - x86/ioapic: Use apic_ack_irq()
+    - x86/platform/uv: Use apic_ack_irq()
+    - irq_remapping: Use apic_ack_irq()
+    - genirq/generic_pending: Do not lose pending affinity update
+    - genirq/affinity: Defer affinity setting if irq chip is busy
+    - genirq/migration: Avoid out of line call if pending is not set
+    - x86/intel_rdt: Enable CMT and MBM on new Skylake stepping
+    - media: uvcvideo: Prevent setting unavailable flags
+    - media: rc: ensure input/lirc device can be opened after register
+    - iwlwifi: fw: harden page loading code
+    - orangefs: set i_size on new symlink
+    - orangefs: report attributes_mask and attributes for statx
+    - HID: intel_ish-hid: ipc: register more pm callbacks to support hibernation
+    - HID: wacom: Correct logical maximum Y for 2nd-gen Intuos Pro large
+    - vhost: fix info leak due to uninitialized memory
+    - mm, page_alloc: do not break __GFP_THISNODE by zonelist reset
+    - Linux 4.17.3
+
+  * Use-after-free in sk_peer_label (LP: #1778646)
+    - SAUCE: apparmor: fix use after free in sk_peer_label
+
+  * kernel: Fix memory leak on CCA and EP11 CPRB processing. (LP: #1775390)
+    - s390/zcrypt: Fix CCA and EP11 CPRB processing failure memory leak.
+
+  * Various fixes for CXL kernel module (LP: #1774471)
+    - cxl: Configure PSL to not use APC virtual machines
+    - cxl: Disable prefault_mode in Radix mode
+
+  * Bluetooth not working (LP: #1764645)
+    - Bluetooth: btusb: Apply QCA Rome patches for some ATH3012 models
+
+  * Fake SAS addresses for SATA disks on HiSilicon D05 are non-unique
+    (LP: #1776750)
+    - scsi: hisi_sas: make SAS address of SATA disks unique
+
+  * linux-snapdragon: wcn36xx: mac address generation on boot (LP: #1776491)
+    - [Config] arm64: snapdragon: WCN36XX_SNAPDRAGON_HACKS=y
+    - SAUCE: wcn36xx: read MAC from file or randomly generate one
+
+  * Lenovo V330 needs patch in ideapad_laptop module for rfkill (LP: #1774636)
+    - SAUCE: Add Lenovo V330 to the ideapad_laptop rfkill blacklist
+
+  * register on binfmt_misc may overflow and crash the system (LP: #1775856)
+    - fs/binfmt_misc.c: do not allow offset overflow
+
+  * Network installs fail on SocioNext board (LP: #1775884)
+    - net: socionext: reset hardware in ndo_stop
+    - net: netsec: enable tx-irq during open callback
+
+  * Fix several bugs in RDMA/hns driver (LP: #1770974)
+    - RDMA/hns: Drop local zgid in favor of core defined variable
+    - RDMA/hns: Add 64KB page size support for hip08
+    - RDMA/hns: Rename the idx field of db
+    - RDMA/hns: Modify uar allocation algorithm to avoid bitmap exhaust
+    - RDMA/hns: Increase checking CMQ status timeout value
+    - RDMA/hns: Add reset process for RoCE in hip08
+    - RDMA/hns: Fix the illegal memory operation when cross page
+    - RDMA/hns: Implement the disassociate_ucontext API
+
+  * powerpc/livepatch: Implement reliable stack tracing for the consistency
+    model (LP: #1771844)
+    - powerpc/livepatch: Implement reliable stack tracing for the consistency
+      model
+
+  * Adding back alx WoL feature (LP: #1772610)
+    - SAUCE: Revert "alx: remove WoL support"
+    - SAUCE: alx: add enable_wol paramenter
+
+  * Lancer A0 Asic HBA's won't boot with 18.04 (LP: #1768103)
+    - scsi: lpfc: Fix WQ/CQ creation for older asic's.
+    - scsi: lpfc: Fix 16gb hbas failing cq create.
+
+  * [LTCTest][OPAL][OP920] cpupower idle-info is not listing stop4 and stop5
+    idle states when all CORES are guarded (LP: #1771780)
+    - powerpc/powernv/cpuidle: Init all present cpus for deep states
+
+  * Huawei 25G/100G Network Adapters Unsupported (LP: #1770970)
+    - net-next/hinic: add pci device ids for 25ge and 100ge card
+
+  * Expose arm64 CPU topology to userspace (LP: #1770231)
+    - drivers: base: cacheinfo: move cache_setup_of_node()
+    - drivers: base: cacheinfo: setup DT cache properties early
+    - cacheinfo: rename of_node to fw_token
+    - arm64/acpi: Create arch specific cpu to acpi id helper
+    - ACPI/PPTT: Add Processor Properties Topology Table parsing
+    - [Config] CONFIG_ACPI_PPTT=y
+    - ACPI: Enable PPTT support on ARM64
+    - drivers: base cacheinfo: Add support for ACPI based firmware tables
+    - arm64: Add support for ACPI based firmware tables
+    - arm64: topology: rename cluster_id
+    - arm64: topology: enable ACPI/PPTT based CPU topology
+    - ACPI: Add PPTT to injectable table list
+    - arm64: topology: divorce MC scheduling domain from core_siblings
+
+  * Vcs-Git header on bionic linux source package points to zesty git tree
+    (LP: #1766055)
+    - [Packaging]: Update Vcs-Git
+
+  * Request to revert SAUCE patches in the 18.04 SRU and update with upstream
+    version (LP: #1768431)
+    - scsi: cxlflash: Handle spurious interrupts
+    - scsi: cxlflash: Remove commmands from pending list on timeout
+    - scsi: cxlflash: Synchronize reset and remove ops
+    - SAUCE: (no-up) cxlflash: OCXL diff between v2 and v3
+
+  * hisi_sas robustness fixes (LP: #1774466)
+    - scsi: hisi_sas: delete timer when removing hisi_sas driver
+    - scsi: hisi_sas: print device id for errors
+    - scsi: hisi_sas: Add some checks to avoid free'ing a sas_task twice
+    - scsi: hisi_sas: check host frozen before calling "done" function
+    - scsi: hisi_sas: check sas_dev gone earlier in hisi_sas_abort_task()
+    - scsi: hisi_sas: stop controller timer for reset
+    - scsi: hisi_sas: update PHY linkrate after a controller reset
+    - scsi: hisi_sas: change slot index allocation mode
+    - scsi: hisi_sas: Change common allocation mode of device id
+    - scsi: hisi_sas: Reset disks when discovered
+    - scsi: hisi_sas: Create a scsi_host_template per HW module
+    - scsi: hisi_sas: Init disks after controller reset
+    - scsi: hisi_sas: Try wait commands before before controller reset
+    - scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
+    - scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
+    - scsi: hisi_sas: Terminate STP reject quickly for v2 hw
+    - scsi: hisi_sas: Fix return value when get_free_slot() failed
+    - scsi: hisi_sas: Mark PHY as in reset for nexus reset
+
+  * hisi_sas: Support newer v3 hardware (LP: #1774467)
+    - scsi: hisi_sas: update RAS feature for later revision of v3 HW
+    - scsi: hisi_sas: check IPTT is valid before using it for v3 hw
+    - scsi: hisi_sas: fix PI memory size
+    - scsi: hisi_sas: config ATA de-reset as an constrained command for v3 hw
+    - scsi: hisi_sas: remove redundant handling to event95 for v3
+    - scsi: hisi_sas: add readl poll timeout helper wrappers
+    - scsi: hisi_sas: workaround a v3 hw hilink bug
+    - scsi: hisi_sas: Add LED feature for v3 hw
+
+  * hisi_sas: improve performance by optimizing DQ locking (LP: #1774472)
+    - scsi: hisi_sas: optimise the usage of DQ locking
+    - scsi: hisi_sas: relocate smp sg map
+    - scsi: hisi_sas: make return type of prep functions void
+    - scsi: hisi_sas: allocate slot buffer earlier
+    - scsi: hisi_sas: Don't lock DQ for complete task sending
+    - scsi: hisi_sas: Use device lock to protect slot alloc/free
+    - scsi: hisi_sas: add check of device in hisi_sas_task_exec()
+    - scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
+
+  * FS-Cache: Assertion failed: FS-Cache: 6 == 5 is false (LP: #1774336)
+    - SAUCE: CacheFiles: fix a read_waiter/read_copier race
+
+  * enable mic-mute hotkey and led on Lenovo M820z and M920z (LP: #1774306)
+    - ALSA: hda/realtek - Enable mic-mute hotkey for several Lenovo AIOs
+
+  * hns3 driver updates (LP: #1768670)
+    - net: hns3: Remove error log when getting pfc stats fails
+    - net: hns3: fix to correctly fetch l4 protocol outer header
+    - net: hns3: Fixes the out of bounds access in hclge_map_tqp
+    - net: hns3: Fixes the error legs in hclge_init_ae_dev function
+    - net: hns3: fix for phy_addr error in hclge_mac_mdio_config
+    - net: hns3: Fix to support autoneg only for port attached with phy
+    - net: hns3: fix a dead loop in hclge_cmd_csq_clean
+    - net: hns3: Fix for packet loss due wrong filter config in VLAN tbls
+    - net: hns3: Remove packet statistics in the range of 8192~12287
+    - net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver
+    - net: hns3: Fix for setting mac address when resetting
+    - net: hns3: remove add/del_tunnel_udp in hns3_enet module
+    - net: hns3: fix for cleaning ring problem
+    - net: hns3: refactor the loopback related function
+    - net: hns3: Fix for deadlock problem occurring when unregistering ae_algo
+    - net: hns3: Fix for the null pointer problem occurring when initializing
+      ae_dev failed
+    - net: hns3: Add a check for client instance init state
+    - net: hns3: Change return type of hnae3_register_ae_dev
+    - net: hns3: Change return type of hnae3_register_ae_algo
+    - net: hns3: Change return value in hnae3_register_client
+    - net: hns3: Fixes the back pressure setting when sriov is enabled
+    - net: hns3: Fix for fiber link up problem
+    - net: hns3: Add support of .sriov_configure in HNS3 driver
+    - net: hns3: Fixes the missing PCI iounmap for various legs
+    - net: hns3: Fixes error reported by Kbuild and internal review
+    - net: hns3: Fixes API to fetch ethernet header length with kernel default
+    - net: hns3: cleanup of return values in hclge_init_client_instance()
+    - net: hns3: Fix the missing client list node initialization
+    - net: hns3: Fix for hns3 module is loaded multiple times problem
+    - net: hns3: Use enums instead of magic number in hclge_is_special_opcode
+    - net: hns3: Fix for netdev not running problem after calling net_stop and
+      net_open
+    - net: hns3: Fixes kernel panic issue during rmmod hns3 driver
+    - net: hns3: Fix for CMDQ and Misc. interrupt init order problem
+    - net: hns3: Updates RX packet info fetch in case of multi BD
+    - net: hns3: Add support for tx_accept_tag2 and tx_accept_untag2 config
+    - net: hns3: Add STRP_TAGP field support for hardware revision 0x21
+    - net: hns3: Add support to enable TX/RX promisc mode for H/W rev(0x21)
+    - net: hns3: Fix for PF mailbox receving unknown message
+    - net: hns3: Fixes the state to indicate client-type initialization
+    - net: hns3: Fixes the init of the VALID BD info in the descriptor
+    - net: hns3: Removes unnecessary check when clearing TX/RX rings
+    - net: hns3: Clear TX/RX rings when stopping port & un-initializing client
+    - net: hns3: Remove unused led control code
+    - net: hns3: Adds support for led locate command for copper port
+    - net: hns3: Fixes initalization of RoCE handle and makes it conditional
+    - net: hns3: Disable vf vlan filter when vf vlan table is full
+    - net: hns3: Add support for IFF_ALLMULTI flag
+    - net: hns3: Add repeat address checking for setting mac address
+    - net: hns3: Fix setting mac address error
+    - net: hns3: Fix for service_task not running problem after resetting
+    - net: hns3: Fix for hclge_reset running repeatly problem
+    - net: hns3: Fix for phy not link up problem after resetting
+    - net: hns3: Add missing break in misc_irq_handle
+    - net: hns3: Fix for vxlan tx checksum bug
+    - net: hns3: Optimize the PF's process of updating multicast MAC
+    - net: hns3: Optimize the VF's process of updating multicast MAC
+    - SAUCE: {topost} net: hns3: add support for serdes loopback selftest
+    - SAUCE: {topost} net: hns3: RX BD information valid only in last BD except
+      VLD bit and buffer size
+    - SAUCE: {topost} net: hns3: remove hclge_get_vector_index from
+      hclge_bind_ring_with_vector
+    - SAUCE: {topost} net: hns3: rename the interface for init_client_instance and
+      uninit_client_instance
+    - SAUCE: {topost} net: hns3: add vector status check before free vector
+    - SAUCE: {topost} net: hns3: add l4_type check for both ipv4 and ipv6
+    - SAUCE: {topost} net: hns3: remove unused head file in hnae3.c
+    - SAUCE: {topost} net: hns3: extraction an interface for state state
+      init|uninit
+    - SAUCE: {topost} net: hns3: print the ret value in error information
+    - SAUCE: {topost} net: hns3: remove the Redundant put_vector in
+      hns3_client_uninit
+    - SAUCE: {topost} net: hns3: add unlikely for error check
+    - SAUCE: {topost} net: hns3: remove back in struct hclge_hw
+    - SAUCE: {topost} net: hns3: use lower_32_bits and upper_32_bits
+    - SAUCE: {topost} net: hns3: remove unused hclge_ring_to_dma_dir
+    - SAUCE: {topost} net: hns3: remove useless code in hclge_cmd_send
+    - SAUCE: {topost} net: hns3: remove some redundant assignments
+    - SAUCE: {topost} net: hns3: simplify hclge_cmd_csq_clean
+    - SAUCE: {topost} net: hns3: using modulo for cyclic counters in
+      hclge_cmd_send
+    - SAUCE: {topost} net: hns3: remove a redundant hclge_cmd_csq_done
+    - SAUCE: {topost} net: hns3: remove some unused members of some structures
+    - SAUCE: {topost} net: hns3: give default option while dependency HNS3 set
+    - SAUCE: {topost} net: hns3: use dma_zalloc_coherent instead of
+      kzalloc/dma_map_single
+    - SAUCE: {topost} net: hns3: modify hnae_ to hnae3_
+    - SAUCE: {topost} net: hns3: fix unused function warning in VF driver
+    - SAUCE: {topost} net: hns3: remove some redundant assignments
+    - SAUCE: {topost} net: hns3: standardize the handle of return value
+    - SAUCE: {topost} net: hns3: remove extra space and brackets
+    - SAUCE: {topost} net: hns3: fix unreasonable code comments
+    - SAUCE: {topost} net: hns3: use decimal for bit offset macros
+    - SAUCE: {topost} net: hns3: modify inconsistent bit mask macros
+    - SAUCE: {topost} net: hns3: fix mislead parameter name
+    - SAUCE: {topost} net: hns3: remove unused struct member and definition
+    - SAUCE: {topost} net: hns3: Add SPDX tags to hns3 driver
+    - SAUCE: {topost} net: hns3: Add pf reset for hip08 RoCE
+    - SAUCE: {topost} net: hns3: optimize the process of notifying roce client
+    - SAUCE: {topost} net: hns3: Add calling roce callback function when link
+      status change
+    - SAUCE: {topost} net: hns3: fix tc setup when netdev is first up
+    - SAUCE: {topost} net: hns3: fix for mac pause not disable in pfc mode
+    - SAUCE: {topost} net: hns3: fix for waterline not setting correctly
+    - SAUCE: {topost} net: hns3: fix for l4 checksum offload bug
+    - SAUCE: {topost} net: hns3: fix for mailbox message truncated problem
+    - SAUCE: {topost} net: hns3: Add configure for mac minimal frame size
+    - SAUCE: {topost} net: hns3: fix warning bug when doing lp selftest
+    - SAUCE: {topost} net: hns3: fix get_vector ops in hclgevf_main module
+    - SAUCE: {topost} net: hns3: remove the warning when clear reset cause
+    - SAUCE: {topost} net: hns3: Use roce handle when calling roce callback
+      function
+    - SAUCE: {topost} net: hns3: prevent sending command during global or core
+      reset
+    - SAUCE: {topost} net: hns3: modify the order of initializeing command queue
+      register
+    - SAUCE: {topost} net: hns3: reset net device with rtnl_lock
+    - SAUCE: {topost} net: hns3: prevent to request reset frequently
+    - SAUCE: {topost} net: hns3: correct reset event status register
+    - SAUCE: {topost} net: hns3: separate roce from nic when resetting
+    - SAUCE: net: hns3: Fix for phy link issue when using marvell phy driver
+    - SAUCE: {topost} net: hns3: fix return value error in
+      hns3_reset_notify_down_enet
+    - SAUCE: {topost} net: hns3: remove unnecessary ring configuration operation
+      while resetting
+    - SAUCE: {topost} net: hns3: fix for reset_level default assignment probelm
+    - SAUCE: {topost} net: hns3: fix for using wrong mask and shift in
+      hclge_get_ring_chain_from_mbx
+    - SAUCE: {topost} net: hns3: fix comments for hclge_get_ring_chain_from_mbx
+    - SAUCE: net: hns3: Fix for VF mailbox cannot receiving PF response
+    - SAUCE: net: hns3: Fix for VF mailbox receiving unknown message
+    - SAUCE: net: hns3: Optimize PF CMDQ interrupt switching process
+
+  * CVE-2018-7755
+    - SAUCE: floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl
+
+  * Incorrect blacklist of bcm2835_wdt (LP: #1766052)
+    - [Packaging] Fix missing watchdog for Raspberry Pi
+
+  * kernel: Fix arch random implementation (LP: #1775391)
+    - s390/archrandom: Rework arch random implementation.
+
+  * [Ubuntu 1804][boston][ixgbe] EEH causes kernel BUG at /build/linux-
+    jWa1Fv/linux-4.15.0/drivers/pci/msi.c:352 (i2S) (LP: #1776389)
+    - ixgbe/ixgbevf: Free IRQ when PCI error recovery removes the device
+
+  * Cosmic update to v4.17.2 stable release (LP: #1779117)
+    - crypto: chelsio - request to HW should wrap
+    - blkdev_report_zones_ioctl(): Use vmalloc() to allocate large buffers
+    - KVM: X86: Fix reserved bits check for MOV to CR3
+    - KVM: x86: introduce linear_{read,write}_system
+    - kvm: fix typo in flag name
+    - kvm: nVMX: Enforce cpl=0 for VMX instructions
+    - KVM: x86: pass kvm_vcpu to kvm_read_guest_virt and
+      kvm_write_guest_virt_system
+    - kvm: x86: use correct privilege level for sgdt/sidt/fxsave/fxrstor access
+    - staging: android: ion: Switch to pr_warn_once in ion_buffer_destroy
+    - NFC: pn533: don't send USB data off of the stack
+    - usbip: vhci_sysfs: fix potential Spectre v1
+    - usb-storage: Add support for FL_ALWAYS_SYNC flag in the UAS driver
+    - usb-storage: Add compatibility quirk flags for G-Technologies G-Drive
+    - Input: xpad - add GPD Win 2 Controller USB IDs
+    - phy: qcom-qusb2: Fix crash if nvmem cell not specified
+    - usb: core: message: remove extra endianness conversion in
+      usb_set_isoch_delay
+    - usb: typec: wcove: Remove dependency on HW FSM
+    - usb: gadget: function: printer: avoid wrong list handling in printer_write()
+    - usb: gadget: udc: renesas_usb3: fix double phy_put()
+    - usb: gadget: udc: renesas_usb3: should remove debugfs
+    - usb: gadget: udc: renesas_usb3: should call pm_runtime_enable() before add
+      udc
+    - usb: gadget: udc: renesas_usb3: should call devm_phy_get() before add udc
+    - usb: gadget: udc: renesas_usb3: should fail if devm_phy_get() returns error
+    - usb: gadget: udc: renesas_usb3: disable the controller's irqs for
+      reconnecting
+    - serial: sh-sci: Stop using printk format %pCr
+    - tty/serial: atmel: use port->name as name in request_irq()
+    - serial: samsung: fix maxburst parameter for DMA transactions
+    - serial: 8250: omap: Fix idling of clocks for unused uarts
+    - vmw_balloon: fixing double free when batching mode is off
+    - doc: fix sysfs ABI documentation
+    - arm64: defconfig: Enable CONFIG_PINCTRL_MT7622 by default
+    - tty: pl011: Avoid spuriously stuck-off interrupts
+    - crypto: ccree - correct host regs offset
+    - Input: goodix - add new ACPI id for GPD Win 2 touch screen
+    - Input: elan_i2c - add ELAN0612 (Lenovo v330 14IKB) ACPI ID
+    - crypto: caam - strip input zeros from RSA input buffer
+    - crypto: caam - fix DMA mapping dir for generated IV
+    - crypto: caam - fix IV DMA mapping and updating
+    - crypto: caam/qi - fix IV DMA mapping and updating
+    - crypto: caam - fix size of RSA prime factor q
+    - crypto: cavium - Fix fallout from CONFIG_VMAP_STACK
+    - crypto: cavium - Limit result reading attempts
+    - crypto: vmx - Remove overly verbose printk from AES init routines
+    - crypto: vmx - Remove overly verbose printk from AES XTS init
+    - crypto: omap-sham - fix memleak
+    - Linux 4.17.2
+
+  * Cosmic update to v4.17.1 stable release (LP: #1779116)
+    - netfilter: nf_flow_table: attach dst to skbs
+    - bnx2x: use the right constant
+    - ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
+    - ipv6: omit traffic class when calculating flow hash
+    - l2tp: fix refcount leakage on PPPoL2TP sockets
+    - netdev-FAQ: clarify DaveM's position for stable backports
+    - net: metrics: add proper netlink validation
+    - net/packet: refine check for priv area size
+    - rtnetlink: validate attributes in do_setlink()
+    - sctp: not allow transport timeout value less than HZ/5 for hb_timer
+    - team: use netdev_features_t instead of u32
+    - vrf: check the original netdevice for generating redirect
+    - net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
+    - ipmr: fix error path when ipmr_new_table fails
+    - PCI: hv: Do not wait forever on a device that has disappeared
+    - Linux 4.17.1
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: SAUCE: crypto: thunderx_zip: Fix fallout from
+      CONFIG_VMAP_STACK"
+    - Revert "UBUNTU: SAUCE: cred: Add clone_cred() interface"
+    - SAUCE: apparmor: userspace queries
+    - SAUCE: apparmor: patch to provide compatibility with v2.x net rules
+    - SAUCE: apparmor: af_unix mediation
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 28 Jun 2018 08:03:32 -0500
+
+linux (4.17.0-2.3) cosmic; urgency=medium
+
+  * linux: 4.17.0-2.3 -proposed tracker (LP: #1776276)
+
+  * Miscellaneous Ubuntu changes
+    - Config: remove IrDA from annotations
+    - Config: remove scsi drivers from annotations
+    - Config: remove BT_HCIBTUART from annotations
+    - Config: pstore zlib support was renamed
+    - Config: disable NVRAM for armhf on annotations
+    - Config: Disable VT on s390x
+    - Config: Update SSB and B43/B44 options
+    - Config: some options not supported on some arches anymore
+    - Config: renamed and removed options
+    - Config: TCG_CRB is required for IMA on ACPI systems
+    - Config: EXTCON_AXP288 depends on X86
+    - Config: CONFIG_FSI depends on OF
+    - Config: DRM_RCAR_LVDS now depends on DRM
+    - CONFIG: Allow CONFIG_LEDS_MLXCPLD for i386
+    - Config: Enable HINIC on arm64
+    - Config: Set PPS and PTP_1588_CLOCK as y
+    - Config: Some NF_TABLES options are built-in now
+    - Config: GENERIC_CPU for ppc64el
+    - Config: KEXEC_FILE=n for s390x
+    - Config: CRYPTO_DEFLATE is needed by PSTORE_DEFLATE_COMPRESS
+    - Config: Disable STM32 support
+    - Config: Enable FORTIFY_SOURCE for armhf
+    - Config: use STRONG instead of AUTO for CC_STACKPROTECTOR
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.17
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Mon, 11 Jun 2018 15:22:10 -0300
+
+linux (4.17.0-1.2) cosmic; urgency=medium
+
+  [ Seth Forshee ]
+  * [Config] enable EDAC_DEBUG on ARM64 (LP: #1772516)
+    - [Config]: set CONFIG_EDAC_DEBUG=y for ARM64
+
+  * Ubuntu 18.04 kernel crashed while in degraded mode (LP: #1770849)
+    - SAUCE: powerpc/perf: Fix memory allocation for core-imc based on
+      num_possible_cpus()
+
+  * Integrated Webcam Realtek Integrated_Webcam_HD (0bda:58f4) not working in
+    DELL XPS 13 9370 with firmware 1.50 (LP: #1763748)
+    - SAUCE: media: uvcvideo: Support realtek's UVC 1.5 device
+
+  * Switch Build-Depends: transfig to fig2dev (LP: #1770770)
+    - [Config] update Build-Depends: transfig to fig2dev
+
+  * update-initramfs not adding i915 GuC firmware for Kaby Lake, firmware fails
+    to load (LP: #1728238)
+    - Revert "UBUNTU: SAUCE: (no-up) i915: Remove MODULE_FIRMWARE statements for
+      unreleased firmware"
+
+  * No driver for Huawei network adapters on arm64 (LP: #1769899)
+    - net-next/hinic: add arm64 support
+
+  * linux-snapdragon: reduce EPROBEDEFER noise during boot (LP: #1768761)
+    - [Config] snapdragon: DRM_I2C_ADV7511=y
+
+  * Add d-i support for Huawei NICs (LP: #1767490)
+    - d-i: add hinic to nic-modules udeb
+
+  * Acer Swift sf314-52 power button not managed  (LP: #1766054)
+    - SAUCE: platform/x86: acer-wmi: add another KEY_POWER keycode
+
+  * Include nfp driver in linux-modules (LP: #1768526)
+    - [Config] Add nfp.ko to generic inclusion list
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Import aufs driver
+    - [Config] Enable AUFS config options
+    - SAUCE: (efi-lockdown) Fix for module sig verification
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) efi: Add an EFI_SECURE_BOOT flag to indicate secure
+      boot mode
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) efi: Don't print secure boot state from the efi stub
+    - [Config] CONFIG_LOCK_DOWN_IN_EFI_SECURE_BOOT=y
+    - SAUCE: (efi-lockdown) really lock down kernel under EFI secure boot
+    - SAUCE: (noup) Update spl to 0.7.5-1ubuntu3, zfs to 0.7.5-1ubuntu17
+    - enable zfs build
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) ima: require secure_boot rules in
+      lockdown mode"
+    - Rebased to v4.17-rc6
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Tue, 22 May 2018 14:48:13 -0300
+
+linux (4.17.0-0.1) bionic; urgency=medium
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.17-rc4
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Tue, 08 May 2018 16:38:51 -0300
+
+linux (4.17.0-0.0) bionic; urgency=medium
+
+  * Dummy entry.
+
+ -- Thadeu Lima de Souza Cascardo <cascardo@canonical.com>  Fri, 27 Apr 2018 11:01:13 -0300
+
+linux (4.16.0-4.5) bionic; urgency=medium
+
+  * [18.04 FEAT] Add kvm_stat from kernel tree (LP: #1734130)
+    - tools/kvm_stat: Fix python3 syntax
+    - tools/kvm_stat: Don't use deprecated file()
+    - tools/kvm_stat: Remove unused function
+    - [Packaging] Add linux-tools-host package for VM host tools
+    - [Config] do_tools_host=true for amd64
+
+  * [Featire] CNL: Enable RAPL support (LP: #1685712)
+    - powercap: RAPL: Add support for Cannon Lake
+
+  * Bionic update to v4.16.2 stable release (LP: #1763388)
+    - sparc64: Oracle DAX driver depends on SPARC64
+    - arp: fix arp_filter on l3slave devices
+    - net: dsa: Discard frames from unused ports
+    - net/ipv6: Increment OUTxxx counters after netfilter hook
+    - net/sched: fix NULL dereference in the error path of tcf_bpf_init()
+    - pptp: remove a buggy dst release in pptp_connect()
+    - sctp: do not leak kernel memory to user space
+    - sctp: sctp_sockaddr_af must check minimal addr length for AF_INET6
+    - vlan: also check phy_driver ts_info for vlan's real device
+    - net: fool proof dev_valid_name()
+    - ip_tunnel: better validate user provided tunnel names
+    - ipv6: sit: better validate user provided tunnel names
+    - ip6_gre: better validate user provided tunnel names
+    - ip6_tunnel: better validate user provided tunnel names
+    - vti6: better validate user provided tunnel names
+    - net_sched: fix a missing idr_remove() in u32_delete_key()
+    - nfp: use full 40 bits of the NSP buffer address
+    - Linux 4.16.2
+
+  * sky2 gigabit ethernet driver sometimes stops working after lid-open resume
+    from sleep (88E8055) (LP: #1758507) // Bionic update to v4.16.2 stable
+    release (LP: #1763388)
+    - sky2: Increase D3 delay to sky2 stops working after suspend
+
+  * Merge the linux-snapdragon kernel into bionic master/snapdragon
+    (LP: #1763040)
+    - arm64: defconfig: enable REMOTEPROC
+    - arm64: defconfig: enable QCOM audio drivers for APQ8016 and DB410c
+    - kernel: configs; add distro.config
+    - arm64: configs: enable WCN36xx
+    - kernel: distro.config: enable debug friendly USB network adpater
+    - arm64: configs: enable QCOM Venus
+    - arm64: defconfig: Enable a53/apcs and avs
+    - arm64: defconfig: enable ondemand governor as default
+    - arm64: defconfig: enable QCOM_TSENS
+    - kernel: configs: enable dm_mod and dm_crypt
+    - Force the SMD regulator driver to be compiled-in
+    - arm64: defconfig: enable CFG80211_DEFAULT_PS by default
+    - arm64: configs: enable BT_QCOMSMD
+    - kernel: configs: add more USB net drivers
+    - arm64: defconfig: disable ANALOG_TV and DIGITAL_TV
+    - arm64: configs: Enable camera drivers
+    - kernel: configs: add freq stat to sysfs
+    - arm64: defconfig: enable CONFIG_USB_CONFIGFS_F_FS by default
+    - arm64: defconfig: Enable QRTR features
+    - kernel: configs: set USB_CONFIG_F_FS in distro.config
+    - kernel: distro.config: enable 'schedutil' CPUfreq governor
+    - kernel: distro.config: enable 'fq' and 'fq_codel' qdiscs
+    - kernel: distro.config: enable 'BBR' TCP congestion algorithm
+    - arm64: defconfig: enable LEDS_QCOM_LPG
+    - HACK: drm/msm/iommu: Remove runtime_put calls in map/unmap
+    - power: avs: Add support for CPR (Core Power Reduction)
+    - power: avs: cpr: Use raw mem access for qfprom
+    - power: avs: cpr: fix with new reg_sequence structures
+    - power: avs: cpr: Register with cpufreq-dt
+    - regulator: smd: Add floor and corner operations
+    - PM / OPP: Support adjusting OPP voltages at runtime
+    - PM / OPP: Drop RCU usage in dev_pm_opp_adjust_voltage()
+    - PM / OPP: HACK: Allow to set regulator without opp_list
+    - PM / OPP: Add a helper to get an opp regulator for device
+    - cpufreq: Add apq8016 to cpufreq-dt-platdev blacklist
+    - regulator: smd: Allow REGULATOR_QCOM_SMD_RPM=m
+    - ov5645: I2C address change
+    - i2c: Add Qualcomm Camera Control Interface driver
+    - camss: vfe: Skip first four frames from sensor
+    - camss: Do not register if no cameras are present
+    - i2c-qcom-cci: Fix run queue completion timeout
+    - i2c-qcom-cci: Fix I2C address bug
+    - media: ov5645: Fix I2C address
+    - drm/bridge/adv7511: Delay clearing of HPD interrupt status
+    - HACK: drm/msm/adv7511: Don't rely on interrupts for EDID parsing
+    - leds: Add driver for Qualcomm LPG
+    - wcn36xx: Fix warning due to duplicate scan_completed notification
+    - arm64: dts: Add CPR DT node for msm8916
+    - arm64: dts: add spmi-regulator nodes
+    - arm64: dts: msm8916: Add cpufreq support
+    - arm64: dts: msm8916: Add a shared CPU opp table
+    - arm64: dts: msm8916: Add cpu cooling maps
+    - arm64: dts: pm8916: Mark the s2 regulator as always-on
+    - arm64: dts: qcom: msm8916: Add msm8916 A53 PLL DT node
+    - arm64: dts: qcom: msm8916: Use the new APCS mailbox driver
+    - arm64: dts: qcom: msm8916: Add clock properties to the APCS node
+    - dt-bindings: media: Binding document for Qualcomm Camera Control Interface
+      driver
+    - MAINTAINERS: Add Qualcomm Camera Control Interface driver
+    - DT: leds: Add Qualcomm Light Pulse Generator binding
+    - arm64: dts: qcom: msm8996: Add mpp and lpg blocks
+    - arm64: dts: qcom: Add pwm node for pm8916
+    - arm64: dts: qcom: Add user LEDs on db820c
+    - arm64: dts: qcom: Add WiFI/BT LEDs on db820c
+    - ARM: dts: qcom: Add LPG node to pm8941
+    - ARM: dts: qcom: honami: Add LPG node and RGB LED
+    - arm64: dts: qcom: Add Camera Control Interface support
+    - arm64: dts: qcom: Add apps_iommu vfe child node
+    - arm64: dts: qcom: Add camss device node
+    - arm64: dts: qcom: Add ov5645 device nodes
+    - arm64: dts: msm8916: Fix camera sensors I2C addresses
+    - arm: dts: qcom: db410c: Enable PWM signal on MPP4
+    - packaging: arm64: add a uboot flavour - part1
+    - packaging: arm64: add a uboot flavour - part2
+    - packaging: arm64: add a uboot flavour - part3
+    - packaging: arm64: add a uboot flavour - part4
+    - packaging: arm64: add a uboot flavour - part5
+    - packaging: arm64: rename uboot flavour to snapdragon
+    - [Config] updateconfigs after qcomlt import
+    - [Config] arm64: snapdragon: COMMON_CLK_QCOM=y
+    - [Config] arm64: snapdragon: MSM_GCC_8916=y
+    - [Config] arm64: snapdragon: REGULATOR_FIXED_VOLTAGE=y
+    - [Config] arm64: snapdragon: PINCTRL_MSM8916=y
+    - [Config] arm64: snapdragon: HWSPINLOCK_QCOM=y
+    - [Config] arm64: snapdragon: SPMI=y, SPMI_MSM_PMIC_ARB=y
+    - [Config] arm64: snapdragon: REGMAP_SPMI=y, PINCTRL_QCOM_SPMI_PMIC=y
+    - [Config] arm64: snapdragon: REGULATOR_QCOM_SPMI=y
+    - [Config] arm64: snapdragon: MFD_SPMI_PMIC=y
+    - [Config] arm64: snapdragon: QCOM_SMEM=y
+    - [Config] arm64: snapdragon: RPMSG=y, RPMSG_QCOM_SMD=y
+    - [Config] arm64: snapdragon: QCOM_SMD_RPM=y, REGULATOR_QCOM_SMD_RPM=y
+    - [Config] arm64: snapdragon: QCOM_CLK_SMD_RPM=y
+    - [Config] arm64: snapdragon: QCOM_BAM_DMA=y
+    - [Config] arm64: snapdragon: QCOM_HIDMA=y, QCOM_HIDMA_MGMT=y
+    - [Config] arm64: snapdragon: QCOM_CPR=y
+    - [Config] arm64: snapdragon: QCOM_QFPROM=y, QCOM_TSENS=y
+    - [Config] arm64: snapdragon: MMC_SDHCI=y, MMC_SDHCI_PLTFM=y, MMC_SDHCI_MSM=y
+    - [Config] turn off DRM_MSM_REGISTER_LOGGING
+    - [Config] arm64: snapdragon: I2C_QUP=y
+    - [Config] arm64: snapdragon: SPI_QUP=y
+    - [Config] arm64: snapdragon: USB_ULPI_BUS=y, PHY_QCOM_USB_HS=y
+    - [Config] arm64: snapdragon: QCOM_APCS_IPC=y
+    - [Config] arm64: snapdragon: QCOM_WCNSS_CTRL=y
+    - [Config] arm64: snapdragon: QCOM_SMSM=y
+    - [Config] arm64: snapdragon: QCOM_SMP2P=y
+    - [Config] arm64: snapdragon: DRM_MSM=y
+    - [Config] arm64: snapdragon: SND_SOC=y
+    - [Config] arm64: snapdragon: QCOM_WCNSS_PIL=m
+    - [Config] arm64: snapdragon: INPUT_PM8941_PWRKEY=y
+    - [Config] arm64: snapdragon: MEDIA_SUBDRV_AUTOSELECT=y, VIDEO_OV5645=m
+    - [Config] arm64: snapdragon: SND_SOC_APQ8016_SBC=y, SND_SOC_LPASS_APQ8016=y
+    - [Config] arm64: snapdragon: SND_SOC_MSM8916_WCD_ANALOG=y,
+      SND_SOC_MSM8916_WCD_DIGITAL=y
+    - SAUCE: media: ov5645: skip address change if dt addr == default addr
+    - SAUCE: drm/msm/adv7511: wrap hacks under CONFIG_ADV7511_SNAPDRAGON_HACKS
+      #ifdefs
+    - [Config] arm64: snapdragon: ADV7511_SNAPDRAGON_HACKS=y
+    - [Packaging] fix up snapdragon abi paths
+
+  * LSM stacking patches for bionic (LP: #1763062)
+    - SAUCE: LSM stacking: procfs: add smack subdir to attrs
+    - SAUCE: LSM stacking: LSM: Manage credential security blobs
+    - SAUCE: LSM stacking: LSM: Manage file security blobs
+    - SAUCE: LSM stacking: LSM: Manage task security blobs
+    - SAUCE: LSM stacking: LSM: Manage remaining security blobs
+    - SAUCE: LSM stacking: LSM: General stacking
+    - SAUCE: LSM stacking: fixup initialize task->security
+    - SAUCE: LSM stacking: fixup: alloc_task_ctx is dead code
+    - SAUCE: LSM stacking: add support for stacking getpeersec_stream
+    - SAUCE: LSM stacking: add stacking support to apparmor network hooks
+    - SAUCE: LSM stacking: fixup apparmor stacking enablement
+    - SAUCE: LSM stacking: fixup stacking kconfig
+    - SAUCE: LSM stacking: allow selecting multiple LSMs using kernel boot params
+    - SAUCE: LSM stacking: provide prctl interface for setting context
+    - SAUCE: LSM stacking: inherit current display LSM
+    - SAUCE: LSM stacking: keep an index for each registered LSM
+    - SAUCE: LSM stacking: verify display LSM
+    - SAUCE: LSM stacking: provide a way to specify the default display lsm
+    - SAUCE: LSM stacking: make sure LSM blob align on 64 bit boundaries
+    - SAUCE: LSM stacking: add /proc/<pid>/attr/display_lsm
+    - SAUCE: LSM stacking: add Kconfig to set default display LSM
+    - SAUCE: LSM stacking: add configs for LSM stacking
+    - SAUCE: LSM stacking: add apparmor and selinux proc dirs
+    - SAUCE: LSM stacking: remove procfs context interface
+
+  * linux 4.13.0-13.14 ADT test failure with linux 4.13.0-13.14
+    (LP: #1720779) // LSM stacking patches for bionic (LP: #1763062)
+    - SAUCE: LSM stacking: check for invalid zero sized writes
+
+  * Support cq/rq record doorbell for RDMA on HSilicon hip08 systems
+    (LP: #1762755)
+    - RDMA/hns: Support rq record doorbell for the user space
+    - RDMA/hns: Support cq record doorbell for the user space
+    - RDMA/hns: Support rq record doorbell for kernel space
+    - RDMA/hns: Support cq record doorbell for kernel space
+    - RDMA/hns: Fix cqn type and init resp
+    - RDMA/hns: Fix init resp when alloc ucontext
+    - RDMA/hns: Fix cq record doorbell enable in kernel
+
+  * Replace LPC patchset with upstream version (LP: #1762758)
+    - Revert "UBUNTU: SAUCE: MAINTAINERS: Add maintainer for HiSilicon LPC driver"
+    - Revert "UBUNTU: SAUCE: HISI LPC: Add ACPI support"
+    - Revert "UBUNTU: SAUCE: ACPI / scan: do not enumerate Indirect IO host
+      children"
+    - Revert "UBUNTU: SAUCE: HISI LPC: Support the LPC host on Hip06/Hip07 with DT
+      bindings"
+    - Revert "UBUNTU: SAUCE: OF: Add missing I/O range exception for indirect-IO
+      devices"
+    - Revert "UBUNTU: SAUCE: PCI: Apply the new generic I/O management on PCI IO
+      hosts"
+    - Revert "UBUNTU: SAUCE: PCI: Add fwnode handler as input param of
+      pci_register_io_range()"
+    - Revert "UBUNTU: SAUCE: PCI: Remove unused __weak attribute in
+      pci_register_io_range()"
+    - Revert "UBUNTU: SAUCE: LIB: Introduce a generic PIO mapping method"
+    - lib: Add generic PIO mapping method
+    - PCI: Remove __weak tag from pci_register_io_range()
+    - PCI: Add fwnode handler as input param of pci_register_io_range()
+    - PCI: Apply the new generic I/O management on PCI IO hosts
+    - of: Add missing I/O range exception for indirect-IO devices
+    - HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
+    - ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
+    - ACPI / scan: Do not enumerate Indirect IO host children
+    - HISI LPC: Add ACPI support
+    - MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
+
+  * Enable Tunneled Operations on POWER9 (LP: #1762448)
+    - powerpc/powernv: Enable tunneled operations
+    - cxl: read PHB indications from the device tree
+
+  * PSL traces reset after PERST for debug AFU image (LP: #1762462)
+    - cxl: Enable NORST bit in PSL_DEBUG register for PSL9
+
+  * NFS + sec=krb5 is broken (LP: #1759791)
+    - sunrpc: remove incorrect HMAC request initialization
+
+  * Raspberry Pi 3 microSD support missing from the installer (LP: #1729128)
+    - d-i: add bcm2835 to block-modules
+
+  * Backport USB core quirks (LP: #1762695)
+    - usb: core: Add "quirks" parameter for usbcore
+    - usb: core: Copy parameter string correctly and remove superfluous null check
+    - usb: core: Add USB_QUIRK_DELAY_CTRL_MSG to usbcore quirks
+
+  * [Ubuntu 18.04] cryptsetup: 'device-mapper: reload ioctl on  failed' when
+    setting up a second end-to-end encrypted disk (LP: #1762353)
+    - SAUCE: s390/crypto: Adjust s390 aes and paes cipher
+
+  * System Z {kernel} UBUNTU18.04 wrong kernel config (LP: #1762719)
+    - s390: move nobp parameter functions to nospec-branch.c
+    - s390: add automatic detection of the spectre defense
+    - s390: report spectre mitigation via syslog
+    - s390: add sysfs attributes for spectre
+    - [Config] CONFIG_EXPOLINE_AUTO=y, CONFIG_KERNEL_NOBP=n for s390
+    - s390: correct nospec auto detection init order
+
+  * Additional spectre and meltdown patches (LP: #1760099) // CVE-2017-5715
+    - powerpc/64s: Wire up cpu_show_spectre_v2()
+
+  * Additional spectre and meltdown patches (LP: #1760099) // CVE-2017-5753
+    - powerpc/64s: Wire up cpu_show_spectre_v1()
+
+  * Additional spectre and meltdown patches (LP: #1760099) // CVE-2017-5754
+    - powerpc/rfi-flush: Move the logic to avoid a redo into the debugfs code
+    - powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again
+    - powerpc/rfi-flush: Always enable fallback flush on pseries
+    - powerpc/rfi-flush: Differentiate enabled and patched flush types
+    - powerpc/rfi-flush: Call setup_rfi_flush() after LPM migration
+    - powerpc/64s: Move cpu_show_meltdown()
+    - powerpc/64s: Enhance the information in cpu_show_meltdown()
+    - powerpc/powernv: Use the security flags in pnv_setup_rfi_flush()
+    - powerpc/pseries: Use the security flags in pseries_setup_rfi_flush()
+
+  * Additional spectre and meltdown patches (LP: #1760099) // CVE-2017-5715 //
+    CVE-2017-5753 // CVE-2017-5754
+    - powerpc/pseries: Add new H_GET_CPU_CHARACTERISTICS flags
+    - powerpc: Add security feature flags for Spectre/Meltdown
+    - powerpc/pseries: Set or clear security feature flags
+    - powerpc/powernv: Set or clear security feature flags
+
+  * Hisilicon network subsystem 3 support (LP: #1761610)
+    - net: hns3: export pci table of hclge and hclgevf to userspace
+    - d-i: Add hns3 drivers to nic-modules
+
+  * "ip a" command on a guest VM shows UNKNOWN status (LP: #1761534)
+    - virtio-net: Fix operstate for virtio when no VIRTIO_NET_F_STATUS
+
+  * perf vendor events arm64: Enable JSON events for ThunderX2 B0 (LP: #1760712)
+    - perf vendor events: Drop incomplete multiple mapfile support
+    - perf vendor events: Fix error code in json_events()
+    - perf vendor events: Drop support for unused topic directories
+    - perf vendor events: Add support for pmu events vendor subdirectory
+    - perf vendor events arm64: Relocate ThunderX2 JSON to cavium subdirectory
+    - perf vendor events arm64: Relocate Cortex A53 JSONs to arm subdirectory
+    - perf vendor events: Add support for arch standard events
+    - perf vendor events arm64: Add armv8-recommended.json
+    - perf vendor events arm64: Fixup ThunderX2 to use recommended events
+    - perf vendor events arm64: fixup A53 to use recommended events
+    - perf vendor events arm64: add HiSilicon hip08 JSON file
+    - perf vendor events arm64: Enable JSON events for ThunderX2 B0
+
+  * Warning "cache flush timed out!" seen when unloading the cxl driver
+    (LP: #1762367)
+    - cxl: Check if PSL data-cache is available before issue flush request
+
+  * Bionic update to v4.16.1 stable release (LP: #1763170)
+    - bitmap: fix memset optimization on big-endian systems
+    - USB: serial: ftdi_sio: add RT Systems VX-8 cable
+    - USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator
+    - USB: serial: cp210x: add ELDAT Easywave RX09 id
+    - serial: 8250: Add Nuvoton NPCM UART
+    - mei: remove dev_err message on an unsupported ioctl
+    - /dev/mem: Avoid overwriting "err" in read_mem()
+    - media: usbtv: prevent double free in error case
+    - parport_pc: Add support for WCH CH382L PCI-E single parallel port card.
+    - crypto: lrw - Free rctx->ext with kzfree
+    - crypto: ccp - Fill the result buffer only on digest, finup, and final ops
+    - crypto: talitos - don't persistently map req_ctx->hw_context and
+      req_ctx->buf
+    - crypto: inside-secure - fix clock management
+    - crypto: testmgr - Fix incorrect values in PKCS#1 test vector
+    - crypto: talitos - fix IPsec cipher in length
+    - crypto: ahash - Fix early termination in hash walk
+    - crypto: caam - Fix null dereference at error path
+    - crypto: ccp - return an actual key size from RSA max_size callback
+    - crypto: arm,arm64 - Fix random regeneration of S_shipped
+    - crypto: x86/cast5-avx - fix ECB encryption when long sg follows short one
+    - Bluetooth: hci_bcm: Add 6 new ACPI HIDs
+    - Btrfs: fix unexpected cow in run_delalloc_nocow
+    - siox: fix possible buffer overflow in device_add_store
+    - staging: comedi: ni_mio_common: ack ai fifo error interrupts.
+    - Revert "base: arch_topology: fix section mismatch build warnings"
+    - Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370
+    - Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list
+    - Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad
+    - vt: change SGR 21 to follow the standards
+    - Fix slab name "biovec-(1<<(21-12))"
+    - signal: Correct the offset of si_pkey and si_lower in struct siginfo on m68k
+    - Linux 4.16.1
+
+  * [18.04][config] regression: nvme and nvme_core couldn't be built as modules
+    starting 4.15-rc2 (LP: #1759893)
+    - SAUCE: Revert "lightnvm: include NVM Express driver if OCSSD is selected for
+      build"
+    - [Config] CONFIG_BLK_DEV_NMVE=m
+
+  * FFe: Enable configuring resume offset via sysfs (LP: #1760106)
+    - PM / hibernate: Make passing hibernate offsets more friendly
+
+  * Ubuntu18.04:POWER9:DD2.2 - Unable to start a KVM guest with default machine
+    type(pseries-bionic) complaining "KVM implementation does not support
+    Transactional Memory, try cap-htm=off" (kvm) (LP: #1752026)
+    - powerpc: Use feature bit for RTC presence rather than timebase presence
+    - powerpc: Book E: Remove unused CPU_FTR_L2CSR bit
+    - powerpc: Free up CPU feature bits on 64-bit machines
+    - powerpc: Add CPU feature bits for TM bug workarounds on POWER9 v2.2
+    - powerpc/powernv: Provide a way to force a core into SMT4 mode
+    - KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9
+    - KVM: PPC: Book3S HV: Work around XER[SO] bug in fake suspend mode
+    - KVM: PPC: Book3S HV: Work around TEXASR bug in fake suspend state
+
+  * [Feature][CFL][ICL] [CNL]Thunderbolt support (Titan Ridge) (LP: #1730775)
+    - thunderbolt: Resume control channel after hibernation image is created
+    - thunderbolt: Serialize PCIe tunnel creation with PCI rescan
+    - thunderbolt: Handle connecting device in place of host properly
+    - thunderbolt: Do not overwrite error code when domain adding fails
+    - thunderbolt: Wait a bit longer for root switch config space
+    - thunderbolt: Wait a bit longer for ICM to authenticate the active NVM
+    - thunderbolt: Handle rejected Thunderbolt devices
+    - thunderbolt: Factor common ICM add and update operations out
+    - thunderbolt: Correct function name in kernel-doc comment
+    - thunderbolt: Add tb_switch_get()
+    - thunderbolt: Add tb_switch_find_by_route()
+    - thunderbolt: Add tb_xdomain_find_by_route()
+    - thunderbolt: Add constant for approval timeout
+    - thunderbolt: Move driver ready handling to struct icm
+    - thunderbolt: Add 'boot' attribute for devices
+    - thunderbolt: Add support for preboot ACL
+    - thunderbolt: Introduce USB only (SL4) security level
+    - thunderbolt: Add support for Intel Titan Ridge
+
+  * QCA9377 requires more IRAM banks for its new firmware (LP: #1748345)
+    - ath10k: update the IRAM bank number for QCA9377
+
+  * Fix an issue that when system in S3, USB keyboard can't wake up the system.
+    (LP: #1759511)
+    - ACPI / PM: Allow deeper wakeup power states with no _SxD nor _SxW
+
+  * cxl: Fix timebase synchronization status on POWER9 missing (CAPI)
+    (LP: #1757228)
+    - cxl: Fix timebase synchronization status on P9
+
+  * [Feature]Update Ubuntu 18.04 lpfc FC driver with 32/64GB HBA support and bug
+    fixes (LP: #1752182)
+    - scsi: lpfc: Fix frequency of Release WQE CQEs
+    - scsi: lpfc: Increase CQ and WQ sizes for SCSI
+    - scsi: lpfc: move placement of target destroy on driver detach
+    - scsi: lpfc: correct debug counters for abort
+    - scsi: lpfc: Add WQ Full Logic for NVME Target
+    - scsi: lpfc: Fix PRLI handling when topology type changes
+    - scsi: lpfc: Fix IO failure during hba reset testing with nvme io.
+    - scsi: lpfc: Fix RQ empty firmware trap
+    - scsi: lpfc: Allow set of maximum outstanding SCSI cmd limit for a target
+    - scsi: lpfc: Fix soft lockup in lpfc worker thread during LIP testing
+    - scsi: lpfc: Fix issue_lip if link is disabled
+    - scsi: lpfc: Indicate CONF support in NVMe PRLI
+    - scsi: lpfc: Fix SCSI io host reset causing kernel crash
+    - scsi: lpfc: Validate adapter support for SRIU option
+    - scsi: lpfc: Fix header inclusion in lpfc_nvmet
+    - scsi: lpfc: Treat SCSI Write operation Underruns as an error
+    - scsi: lpfc: Fix nonrecovery of NVME controller after cable swap.
+    - scsi: lpfc: update driver version to 11.4.0.7
+    - scsi: lpfc: Update 11.4.0.7 modified files for 2018 Copyright
+    - scsi: lpfc: Rework lpfc to allow different sli4 cq and eq handlers
+    - scsi: lpfc: Rework sli4 doorbell infrastructure
+    - scsi: lpfc: Add SLI-4 if_type=6 support to the code base
+    - scsi: lpfc: Add push-to-adapter support to sli4
+    - scsi: lpfc: Add PCI Ids for if_type=6 hardware
+    - scsi: lpfc: Add 64G link speed support
+    - scsi: lpfc: Add if_type=6 support for cycling valid bits
+    - scsi: lpfc: Enable fw download on if_type=6 devices
+    - scsi: lpfc: Add embedded data pointers for enhanced performance
+    - scsi: lpfc: Fix nvme embedded io length on new hardware
+    - scsi: lpfc: Work around NVME cmd iu SGL type
+    - scsi: lpfc: update driver version to 12.0.0.0
+    - scsi: lpfc: Change Copyright of 12.0.0.0 modified files to 2018
+    - scsi: lpfc: use __raw_writeX on DPP copies
+    - scsi: lpfc: Add missing unlock in WQ full logic
+
+  * /dev/bcache/by-uuid links not created after reboot (LP: #1729145)
+    - SAUCE: (no-up) bcache: decouple emitting a cached_dev CHANGE uevent
+
+  * DKMS driver builds fail with: Cannot use CONFIG_STACK_VALIDATION=y, please
+    install libelf-dev, libelf-devel or elfutils-libelf-devel (LP: #1760876)
+    - [Packaging] include the retpoline extractor in the headers
+
+  * Use med_with_dipm SATA LPM to save more power for mobile platforms
+    (LP: #1759547)
+    - [Config] CONFIG_SATA_MOBILE_LPM_POLICY=3
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] Only install cloud init files when do_tools_common=true
+    - SAUCE: Import aufs driver
+    - [Config] Enable AUFS config options
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 12 Apr 2018 09:30:56 -0500
+
+linux (4.16.0-3.4) bionic; urgency=medium
+
+  * Allow multiple mounts of zfs datasets (LP: #1759848)
+    - SAUCE: Allow mounting datasets more than once (LP: #1759848)
+
+  * zfs system process hung on container stop/delete (LP: #1754584)
+    - SAUCE: Fix non-prefaulted page deadlock (LP: #1754584)
+    - Revert "UBUNTU: SAUCE: Fix non-prefaulted page deadlock (LP: #1754584)"
+    - SAUCE: Fix non-prefaulted page deadlock (LP: #1754584)
+
+  * ubuntu_zram_smoke test will cause soft lockup on Artful ThunderX ARM64
+    (LP: #1755073)
+    - SAUCE: crypto: thunderx_zip: Fix fallout from CONFIG_VMAP_STACK
+
+  * CAPI Flash (cxlflash) update (LP: #1752672)
+    - SAUCE: cxlflash: Preserve number of interrupts for master contexts
+    - SAUCE: cxlflash: Avoid clobbering context control register value
+    - SAUCE: cxlflash: Add argument identifier names
+    - SAUCE: cxlflash: Introduce OCXL backend
+    - SAUCE: cxlflash: Hardware AFU for OCXL
+    - SAUCE: cxlflash: Read host function configuration
+    - SAUCE: cxlflash: Setup function acTag range
+    - SAUCE: cxlflash: Read host AFU configuration
+    - SAUCE: cxlflash: Setup AFU acTag range
+    - SAUCE: cxlflash: Setup AFU PASID
+    - SAUCE: cxlflash: Adapter context support for OCXL
+    - SAUCE: cxlflash: Use IDR to manage adapter contexts
+    - SAUCE: cxlflash: Support adapter file descriptors for OCXL
+    - SAUCE: cxlflash: Support adapter context discovery
+    - SAUCE: cxlflash: Support image reload policy modification
+    - SAUCE: cxlflash: MMIO map the AFU
+    - SAUCE: cxlflash: Support starting an adapter context
+    - SAUCE: cxlflash: Support process specific mappings
+    - SAUCE: cxlflash: Support AFU state toggling
+    - SAUCE: cxlflash: Support reading adapter VPD data
+    - SAUCE: cxlflash: Setup function OCXL link
+    - SAUCE: cxlflash: Setup OCXL transaction layer
+    - SAUCE: cxlflash: Support process element lifecycle
+    - SAUCE: cxlflash: Support AFU interrupt management
+    - SAUCE: cxlflash: Support AFU interrupt mapping and registration
+    - SAUCE: cxlflash: Support starting user contexts
+    - SAUCE: cxlflash: Support adapter context polling
+    - SAUCE: cxlflash: Support adapter context reading
+    - SAUCE: cxlflash: Support adapter context mmap and release
+    - SAUCE: cxlflash: Support file descriptor mapping
+    - SAUCE: cxlflash: Introduce object handle fop
+    - SAUCE: cxlflash: Setup LISNs for user contexts
+    - SAUCE: cxlflash: Setup LISNs for master contexts
+    - SAUCE: cxlflash: Update synchronous interrupt status bits
+    - SAUCE: cxlflash: Introduce OCXL context state machine
+    - SAUCE: cxlflash: Register for translation errors
+    - SAUCE: cxlflash: Support AFU reset
+    - SAUCE: cxlflash: Enable OCXL operations
+
+  * [Artful][Wyse 3040] System hang when trying to enable an offlined CPU core
+    (LP: #1736393)
+    - SAUCE: drm/i915:Don't set chip specific data
+    - SAUCE: drm/i915: make previous commit affects Wyse 3040 only
+
+  * zed process consuming 100% cpu (LP: #1751796)
+    - SAUCE: Fix ioctl loop-spin in zed (LP: #1751796)
+
+  * Ubuntu18.04:PowerPC - Set Transparent Huge Pages (THP) by default to
+    "always" (LP: #1753708)
+    - Config: Set TRANSPARENT_HUGEPAGE_ALWAYS=y on ppc64el
+
+  * retpoline hints: primary infrastructure and initial hints (LP: #1758856)
+    - [Packaging] retpoline -- add safe usage hint support
+    - [Packaging] retpoline-check -- only report additions
+    - [Packaging] retpoline -- widen indirect call/jmp detection
+    - [Packaging] retpoline -- elide %rip relative indirections
+    - [Packaging] retpoline -- clear hint information from packages
+    - SAUCE: apm -- annotate indirect calls within
+      firmware_restrict_branch_speculation_{start,end}
+    - SAUCE: EFI -- annotate indirect calls within
+      firmware_restrict_branch_speculation_{start,end}
+    - SAUCE: early/late -- annotate indirect calls in early/late initialisation
+      code
+    - SAUCE: vga_set_mode -- avoid jump tables
+    - [Config] retpoine -- switch to new format
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] final-checks -- remove check for empty retpoline files
+    - [Packaging] skip cloud tools packaging when not building package
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.16
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 02 Apr 2018 16:15:36 -0500
+
+linux (4.16.0-2.3) bionic; urgency=medium
+
+  * devpts: handle bind-mounts (LP: #1755857)
+    - SAUCE: devpts: hoist out check for DEVPTS_SUPER_MAGIC
+    - SAUCE: devpts: resolve devpts bind-mounts
+    - SAUCE: devpts: comment devpts_mntget()
+    - SAUCE: selftests: add devpts selftests
+
+  * [bionic][arm64] d-i: add hisi_sas_v3_hw to scsi-modules (LP: #1756103)
+    - d-i: add hisi_sas_v3_hw to scsi-modules
+
+  * [Bionic][ARM64] PCI and SAS driver patches for hip08 SoCs (LP: #1756094)
+    - SAUCE: scsi: hisi_sas: config for hip08 ES
+    - SAUCE: scsi: hisi_sas: export device table of v3 hw to userspace
+
+  * s390/crypto: Fix kernel crash on aes_s390 module remove (LP: #1753424)
+    - SAUCE: s390/crypto: Fix kernel crash on aes_s390 module remove.
+
+  * Fix ARC hit rate (LP: #1755158)
+    - SAUCE: Fix ARC hit rate (LP: #1755158)
+
+  * ZFS setgid broken on 0.7 (LP: #1753288)
+    - SAUCE: Fix ZFS setgid
+
+  * CONFIG_EFI=y on armhf (LP: #1726362)
+    - [Config] CONFIG_EFI=y on armhf, reconcile secureboot EFI settings
+
+  * [Feature] Add xHCI debug device support in the driver (LP: #1730832)
+    - [Config] CONFIG_USB_XHCI_DBGCAP=y
+
+  * retpoline: ignore %cs:0xNNN constant indirections (LP: #1752655)
+    - [Packaging] retpoline -- elide %cs:0xNNNN constants on i386
+    - [Config] retpoline -- clean up i386 retpoline files
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] retpoline-extract: flag *0xNNN(%reg) branches
+    - [Config] fix up retpoline abi files
+    - [Config] fix up retpoline abi files
+    - d-i: Add netsec to nic-modules
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.16-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 19 Mar 2018 14:09:49 -0500
+
+linux (4.16.0-1.2) bionic; urgency=medium
+
+  * Driver not found in Ubuntu kernel does not detect interface (LP: #1745927)
+    - d-i: add cxgb4 to nic-modules
+
+  * Support low-pin-count devices on Hisilicon SoCs (LP: #1677319)
+    - [Config] CONFIG_INDIRECT_PIO=y
+    - SAUCE: LIB: Introduce a generic PIO mapping method
+    - SAUCE: PCI: Remove unused __weak attribute in pci_register_io_range()
+    - SAUCE: PCI: Add fwnode handler as input param of pci_register_io_range()
+    - SAUCE: PCI: Apply the new generic I/O management on PCI IO hosts
+    - SAUCE: OF: Add missing I/O range exception for indirect-IO devices
+    - [Config] CONFIG_HISILICON_LPC=y
+    - SAUCE: HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
+    - SAUCE: ACPI / scan: do not enumerate Indirect IO host children
+    - SAUCE: HISI LPC: Add ACPI support
+    - SAUCE: MAINTAINERS: Add maintainer for HiSilicon LPC driver
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: tools: use CC for linking acpi tools
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.16-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 28 Feb 2018 10:17:23 -0600
+
+linux (4.16.0-0.1) bionic; urgency=medium
+
+  * retpoline abi files are empty on i386 (LP: #1751021)
+    - [Packaging] retpoline-extract -- instantiate retpoline files for i386
+    - [Packaging] final-checks -- sanity checking ABI contents
+    - [Packaging] final-checks -- check for empty retpoline files
+
+  * Miscellaneous upstream changes
+    - disable vbox build
+    - Disable zfs build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.16-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 22 Feb 2018 08:58:57 -0600
+
+linux (4.16.0-0.0) bionic; urgency=medium
+
+  * Dummy entry
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 21 Feb 2018 14:33:13 -0600
+
+linux (4.15.0-10.11) bionic; urgency=medium
+
+  * linux: 4.15.0-10.11 -proposed tracker (LP: #1749250)
+
+  * "swiotlb: coherent allocation failed" dmesg spam with linux 4.15.0-9.10
+    (LP: #1749202)
+    - swiotlb: suppress warning when __GFP_NOWARN is set
+    - drm/ttm: specify DMA_ATTR_NO_WARN for huge page pools
+
+  * linux-tools: perf incorrectly linking libbfd (LP: #1748922)
+    - SAUCE: tools -- add ability to disable libbfd
+    - [Packaging] correct disablement of libbfd
+
+  * [Artful] Realtek ALC225: 2 secs noise when a headset plugged in
+    (LP: #1744058)
+    - ALSA: hda/realtek - update ALC225 depop optimize
+
+  * [Artful] Support headset mode for DELL WYSE (LP: #1723913)
+    - SAUCE: ALSA: hda/realtek - Add support headset mode for DELL WYSE
+
+  * headset mic can't be detected on two Dell machines (LP: #1748807)
+    - ALSA: hda/realtek - Support headset mode for ALC215/ALC285/ALC289
+    - ALSA: hda - Fix headset mic detection problem for two Dell machines
+
+  * Bionic update to v4.15.3 stable release (LP: #1749191)
+    - ip6mr: fix stale iterator
+    - net: igmp: add a missing rcu locking section
+    - qlcnic: fix deadlock bug
+    - qmi_wwan: Add support for Quectel EP06
+    - r8169: fix RTL8168EP take too long to complete driver initialization.
+    - tcp: release sk_frag.page in tcp_disconnect
+    - vhost_net: stop device during reset owner
+    - ipv6: addrconf: break critical section in addrconf_verify_rtnl()
+    - ipv6: change route cache aging logic
+    - Revert "defer call to mem_cgroup_sk_alloc()"
+    - net: ipv6: send unsolicited NA after DAD
+    - rocker: fix possible null pointer dereference in
+      rocker_router_fib_event_work
+    - tcp_bbr: fix pacing_gain to always be unity when using lt_bw
+    - cls_u32: add missing RCU annotation.
+    - ipv6: Fix SO_REUSEPORT UDP socket with implicit sk_ipv6only
+    - soreuseport: fix mem leak in reuseport_add_sock()
+    - net_sched: get rid of rcu_barrier() in tcf_block_put_ext()
+    - net: sched: fix use-after-free in tcf_block_put_ext
+    - media: mtk-vcodec: add missing MODULE_LICENSE/DESCRIPTION
+    - media: soc_camera: soc_scale_crop: add missing
+      MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - media: tegra-cec: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - gpio: uniphier: fix mismatch between license text and MODULE_LICENSE
+    - crypto: tcrypt - fix S/G table for test_aead_speed()
+    - Linux 4.15.3
+
+  * bnx2x_attn_int_deasserted3:4323 MC assert! (LP: #1715519) //
+    CVE-2018-1000026
+    - net: create skb_gso_validate_mac_len()
+    - bnx2x: disable GSO where gso_size is too big for hardware
+
+  * ethtool -p fails to light NIC LED on HiSilicon D05 systems (LP: #1748567)
+    - net: hns: add ACPI mode support for ethtool -p
+
+  * CVE-2017-5715 (Spectre v2 Intel)
+    - [Packaging] retpoline files must be sorted
+    - [Packaging] pull in retpoline files
+
+  * [Feature] PXE boot with Intel Omni-Path (LP: #1712031)
+    - d-i: Add hfi1 to nic-modules
+
+  * CVE-2017-5715 (Spectre v2 retpoline)
+    - [Packaging] retpoline -- add call site validation
+    - [Config] disable retpoline checks for first upload
+
+  * Do not duplicate changelog entries assigned to more than one bug or CVE
+    (LP: #1743383)
+    - [Packaging] git-ubuntu-log -- handle multiple bugs/cves better
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 13 Feb 2018 11:33:58 -0600
+
+linux (4.15.0-9.10) bionic; urgency=medium
+
+  * linux: 4.15.0-9.10 -proposed tracker (LP: #1748244)
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] tests -- remove gcc-multilib dependency for arm64
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 08 Feb 2018 11:25:04 -0600
+
+linux (4.15.0-8.9) bionic; urgency=medium
+
+  * linux: 4.15.0-8.9 -proposed tracker (LP: #1748075)
+
+  * Bionic update to v4.15.2 stable release (LP: #1748072)
+    - KVM: x86: Make indirect calls in emulator speculation safe
+    - KVM: VMX: Make indirect call speculation safe
+    - module/retpoline: Warn about missing retpoline in module
+    - x86/cpufeatures: Add CPUID_7_EDX CPUID leaf
+    - x86/cpufeatures: Add Intel feature bits for Speculation Control
+    - x86/cpufeatures: Add AMD feature bits for Speculation Control
+    - x86/msr: Add definitions for new speculation control MSRs
+    - x86/pti: Do not enable PTI on CPUs which are not vulnerable to Meltdown
+    - x86/cpufeature: Blacklist SPEC_CTRL/PRED_CMD on early Spectre v2 microcodes
+    - x86/speculation: Add basic IBPB (Indirect Branch Prediction Barrier) support
+    - x86/alternative: Print unadorned pointers
+    - x86/nospec: Fix header guards names
+    - x86/bugs: Drop one "mitigation" from dmesg
+    - x86/cpu/bugs: Make retpoline module warning conditional
+    - x86/cpufeatures: Clean up Spectre v2 related CPUID flags
+    - x86/retpoline: Simplify vmexit_fill_RSB()
+    - x86/speculation: Simplify indirect_branch_prediction_barrier()
+    - auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - iio: adc/accel: Fix up module licenses
+    - pinctrl: pxa: pxa2xx: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - ASoC: pcm512x: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - KVM: nVMX: Eliminate vmcs02 pool
+    - KVM: VMX: introduce alloc_loaded_vmcs
+    - objtool: Improve retpoline alternative handling
+    - objtool: Add support for alternatives at the end of a section
+    - objtool: Warn on stripped section symbol
+    - x86/mm: Fix overlap of i386 CPU_ENTRY_AREA with FIX_BTMAP
+    - x86/spectre: Check CONFIG_RETPOLINE in command line parser
+    - x86/entry/64: Remove the SYSCALL64 fast path
+    - x86/entry/64: Push extra regs right away
+    - x86/asm: Move 'status' from thread_struct to thread_info
+    - Documentation: Document array_index_nospec
+    - array_index_nospec: Sanitize speculative array de-references
+    - x86: Implement array_index_mask_nospec
+    - x86: Introduce barrier_nospec
+    - x86: Introduce __uaccess_begin_nospec() and uaccess_try_nospec
+    - x86/usercopy: Replace open coded stac/clac with __uaccess_{begin, end}
+    - x86/uaccess: Use __uaccess_begin_nospec() and uaccess_try_nospec
+    - x86/get_user: Use pointer masking to limit speculation
+    - x86/syscall: Sanitize syscall table de-references under speculation
+    - vfs, fdtable: Prevent bounds-check bypass via speculative execution
+    - nl80211: Sanitize array index in parse_txq_params
+    - x86/spectre: Report get_user mitigation for spectre_v1
+    - x86/spectre: Fix spelling mistake: "vunerable"-> "vulnerable"
+    - x86/cpuid: Fix up "virtual" IBRS/IBPB/STIBP feature bits on Intel
+    - x86/speculation: Use Indirect Branch Prediction Barrier in context switch
+    - x86/paravirt: Remove 'noreplace-paravirt' cmdline option
+    - KVM: VMX: make MSR bitmaps per-VCPU
+    - x86/kvm: Update spectre-v1 mitigation
+    - x86/retpoline: Avoid retpolines for built-in __init functions
+    - x86/spectre: Simplify spectre_v2 command line parsing
+    - x86/pti: Mark constant arrays as __initconst
+    - x86/speculation: Fix typo IBRS_ATT, which should be IBRS_ALL
+    - KVM/x86: Update the reverse_cpuid list to include CPUID_7_EDX
+    - KVM/x86: Add IBPB support
+    - KVM/VMX: Emulate MSR_IA32_ARCH_CAPABILITIES
+    - KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL
+    - KVM/SVM: Allow direct access to MSR_IA32_SPEC_CTRL
+    - serial: core: mark port as initialized after successful IRQ change
+    - fpga: region: release of_parse_phandle nodes after use
+    - Linux 4.15.2
+
+  * Add support for the NIC on SynQuacer E-Series boards (LP: #1747792)
+    - net: phy: core: remove now uneeded disabling of interrupts
+    - [Config] CONFIG_NET_VENDOR_SOCIONEXT=y & CONFIG_SNI_NETSEC=m
+    - net: socionext: Add Synquacer NetSec driver
+    - net: socionext: include linux/io.h to fix build
+    - net: socionext: Fix error return code in netsec_netdev_open()
+
+  * [Artful/Bionic] [Config] enable EDAC_GHES for ARM64 (LP: #1747746)
+    - [Config] CONFIG_EDAC_GHES=y
+
+  * support thunderx2 vendor pmu events (LP: #1747523)
+    - perf pmu: Pass pmu as a parameter to get_cpuid_str()
+    - perf tools arm64: Add support for get_cpuid_str function.
+    - perf pmu: Add helper function is_pmu_core to detect PMU CORE devices
+    - perf vendor events arm64: Add ThunderX2 implementation defined pmu core
+      events
+    - perf pmu: Add check for valid cpuid in perf_pmu__find_map()
+
+  * linux 4.14.0-7.9 ADT test failure with linux 4.14.0-7.9 (LP: #1732463)
+    - SAUCE: mm: disable vma based swap readahead by default
+    - SAUCE: mm: fix memory hotplug in ZONE_HIGHMEM
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Fix CONFIG_PROFILE_ALL_BRANCHES annotations
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 07 Feb 2018 21:13:27 -0600
+
+linux (4.15.0-7.8) bionic; urgency=medium
+
+  * Bionic update to v4.15.1 stable release (LP: #1747169)
+    - Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops
+    - tools/gpio: Fix build error with musl libc
+    - gpio: stmpe: i2c transfer are forbiden in atomic context
+    - gpio: Fix kernel stack leak to userspace
+    - ALSA: hda - Reduce the suspend time consumption for ALC256
+    - crypto: ecdh - fix typo in KPP dependency of CRYPTO_ECDH
+    - crypto: aesni - handle zero length dst buffer
+    - crypto: aesni - fix typo in generic_gcmaes_decrypt
+    - crypto: aesni - add wrapper for generic gcm(aes)
+    - crypto: aesni - Fix out-of-bounds access of the data buffer in generic-gcm-
+      aesni
+    - crypto: aesni - Fix out-of-bounds access of the AAD buffer in generic-gcm-
+      aesni
+    - crypto: inside-secure - fix hash when length is a multiple of a block
+    - crypto: inside-secure - avoid unmapping DMA memory that was not mapped
+    - crypto: sha3-generic - fixes for alignment and big endian operation
+    - crypto: af_alg - whitelist mask and type
+    - HID: wacom: EKR: ensure devres groups at higher indexes are released
+    - HID: wacom: Fix reporting of touch toggle (WACOM_HID_WD_MUTE_DEVICE) events
+    - power: reset: zx-reboot: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - gpio: iop: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - gpio: ath79: add missing MODULE_DESCRIPTION/LICENSE
+    - mtd: nand: denali_pci: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
+    - igb: Free IRQs when device is hotplugged
+    - ima/policy: fix parsing of fsuuid
+    - scsi: aacraid: Fix udev inquiry race condition
+    - scsi: aacraid: Fix hang in kdump
+    - scsi: storvsc: missing error code in storvsc_probe()
+    - staging: lustre: separate a connection destroy from free struct kib_conn
+    - staging: ccree: NULLify backup_info when unused
+    - staging: ccree: fix fips event irq handling build
+    - tty: fix data race between tty_init_dev and flush of buf
+    - usb: option: Add support for FS040U modem
+    - USB: serial: pl2303: new device id for Chilitag
+    - USB: cdc-acm: Do not log urb submission errors on disconnect
+    - CDC-ACM: apply quirk for card reader
+    - USB: serial: io_edgeport: fix possible sleep-in-atomic
+    - usbip: prevent bind loops on devices attached to vhci_hcd
+    - usbip: list: don't list devices attached to vhci_hcd
+    - USB: serial: simple: add Motorola Tetra driver
+    - usb: f_fs: Prevent gadget unbind if it is already unbound
+    - usb: uas: unconditionally bring back host after reset
+    - usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
+    - ANDROID: binder: remove waitqueue when thread exits.
+    - android: binder: use VM_ALLOC to get vm area
+    - mei: me: allow runtime pm for platform with D0i3
+    - serial: 8250_of: fix return code when probe function fails to get reset
+    - serial: 8250_uniphier: fix error return code in uniphier_uart_probe()
+    - serial: 8250_dw: Revert "Improve clock rate setting"
+    - serial: imx: Only wakeup via RTSDEN bit if the system has RTS/CTS
+    - spi: imx: do not access registers while clocks disabled
+    - iio: adc: stm32: fix scan of multiple channels with DMA
+    - iio: chemical: ccs811: Fix output of IIO_CONCENTRATION channels
+    - test_firmware: fix missing unlock on error in config_num_requests_store()
+    - Input: synaptics-rmi4 - unmask F03 interrupts when port is opened
+    - Input: synaptics-rmi4 - do not delete interrupt memory too early
+    - x86/efi: Clarify that reset attack mitigation needs appropriate userspace
+    - Linux 4.15.1
+
+  * Dell XPS 13 9360 bluetooth (Atheros) won't connect after resume
+    (LP: #1744712)
+    - Revert "Bluetooth: btusb: fix QCA Rome suspend/resume"
+    - Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten"
+      version
+
+  * apparmor profile load in stacked policy container fails (LP: #1746463)
+    - SAUCE: apparmor: fix display of .ns_name for containers
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 04 Feb 2018 11:56:32 +0100
+
+linux (4.15.0-6.7) bionic; urgency=low
+
+  * upload urgency should be medium by default (LP: #1745338)
+    - [Packaging] update urgency to medium by default
+
+  * Shutdown hang on 16.04 with iscsi targets (LP: #1569925)
+    - scsi: libiscsi: Allow sd_shutdown on bad transport
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.7.5-1ubuntu1, zfs to 0.7.5-1ubuntu1
+    - Revert "UBUNTU: SAUCE: mm: fix memory hotplug in ZONE_HIGHMEM"
+    - Revert "UBUNTU: SAUCE: mm: disable vma based swap readahead by default"
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 29 Jan 2018 08:47:07 -0600
+
+linux (4.15.0-5.6) bionic; urgency=low
+
+  * $(LOCAL_ENV_CC) and $(LOCAL_ENV_DISTCC_HOSTS) should be properly quoted
+    (LP: #1744077)
+    - [Debian] pass LOCAL_ENV_CC and LOCAL_ENV_DISTCC_HOSTS properly
+
+  * Missing install-time driver for QLogic QED 25/40/100Gb Ethernet NIC
+    (LP: #1743638)
+    - [d-i] Add qede to nic-modules udeb
+
+  * boot failure on AMD Raven + WesternXT (LP: #1742759)
+    - SAUCE: drm/amdgpu: add atpx quirk handling (v2)
+
+  * Unable to handle kernel NULL pointer dereference at isci_task_abort_task
+    (LP: #1726519)
+    - SAUCE: Revert "scsi: libsas: allow async aborts"
+
+  * Update Ubuntu-4.15.0 config to support Intel Atom devices (LP: #1739939)
+    - [Config] CONFIG_SERIAL_DEV_BUS=y, CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
+
+  * Miscellaneous Ubuntu changes
+    - Rebase to v4.15-rc7
+    - [Config] CONFIG_CPU_ISOLATION=y
+    - [Config] Update annotations following config review
+    - Revert "UBUNTU: SAUCE: Import aufs driver"
+    - SAUCE: Import aufs driver
+    - ubuntu: vbox -- update to 5.2.6-dfsg-1
+    - ubuntu: vbox: build fixes for 4.15
+    - ubuntu: vbox -- update to 5.2.6-dfsg-2
+    - hio: updates for timer api changes in 4.15
+    - enable hio build
+    - Rebase to v4.15-rc9
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15-rc9
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 22 Jan 2018 10:16:05 -0600
+
+linux (4.15.0-4.5) bionic; urgency=low
+
+  * [0cf3:e010] QCA6174A XR failed to pair with bt 4.0 device  (LP: #1741166)
+    - SAUCE: Bluetooth: btusb: Add support for 0cf3:e010
+
+  * External HDMI monitor failed to show screen on Lenovo X1 series
+    (LP: #1738523)
+    - SAUCE: drm/i915: Disable writing of TMDS_OE on Lenovo ThinkPad X1 series
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] autoreconstruct - add resoration of execute permissions
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 10 Jan 2018 10:24:22 -0600
+
+linux (4.15.0-3.4) bionic; urgency=low
+
+  * ubuntu/xr-usb-serial didn't get built in zesty and artful (LP: #1733281)
+    - SAUCE: make sure ubuntu/xr-usb-serial builds for x86
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 03 Jan 2018 20:20:43 -0600
+
+linux (4.15.0-2.3) bionic; urgency=low
+
+  * nvidia-graphics-drivers-384 384.90-0ubuntu6 ADT test failure with linux
+    4.15.0-1.2 (LP: #1737752)
+    - x86/mm: Unbreak modules that use the DMA API
+
+  * Ubuntu 17.10 corrupting BIOS - many LENOVO laptops models (LP: #1734147)
+    - [Config] CONFIG_SPI_INTEL_SPI_*=n
+
+  * power: commonise configs IBMVETH/IBMVSCSI and ensure both are in linux-image
+    and udebs (LP: #1521712)
+    - [Config] Include ibmvnic in nic-modules
+
+  * Enable arm64 emulation of removed ARMv7 instructions (LP: #1545542)
+    - [Config] Enable support for emulation of deprecated ARMv8 instructions
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl with 4.15 compat fix (LP:#1737761)
+    - Enable zfs build
+    - [Debian] add icp to zfs-modules.ignore
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 18 Dec 2017 09:27:13 -0600
+
+linux (4.15.0-1.2) bionic; urgency=low
+
+  * Disabling zfs does not always disable module checks for the zfs modules
+    (LP: #1737176)
+    - [Packaging] disable zfs module checks when zfs is disabled
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_UNWINDER_FRAME_POINTER=y for amd64
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 10 Dec 2017 22:07:19 -0600
+
+linux (4.15.0-0.1) bionic; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - ubuntu: vbox -- update to 5.2.2-dfsg-2
+    - ubuntu: vbox: build fixes for 4.15
+    - disable hio build
+    - [Config] Update kernel lockdown options to fix build errors
+    - Disable zfs build
+    - SAUCE: Import aufs driver
+    - [Config] Enable AUFS config options
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.15-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 08 Dec 2017 13:55:42 -0600
+
+linux (4.14.0-11.13) bionic; urgency=low
+
+  * linux: 4.14.0-11.13 -proposed tracker (LP: #1736168)
+
+  * CVE-2017-1000405
+    - mm, thp: Do not make page table dirty unconditionally in touch_p[mu]d()
+
+  * linux 4.14.0-7.9 ADT test failure with linux 4.14.0-7.9 (LP: #1732463)
+    - SAUCE: mm: disable vma based swap readahead by default
+    - SAUCE: mm: fix memory hotplug in ZONE_HIGHMEM
+
+  * Bionic update to v4.14.3 stable release (LP: #1735843)
+    - s390: fix transactional execution control register handling
+    - s390/noexec: execute kexec datamover without DAT
+    - s390/runtime instrumention: fix possible memory corruption
+    - s390/guarded storage: fix possible memory corruption
+    - s390/disassembler: add missing end marker for e7 table
+    - s390/disassembler: increase show_code buffer size
+    - ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
+    - ACPI / EC: Fix regression related to triggering source of EC event handling
+    - cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
+    - serdev: fix registration of second slave
+    - sched: Make resched_cpu() unconditional
+    - lib/mpi: call cond_resched() from mpi_powm() loop
+    - x86/boot: Fix boot failure when SMP MP-table is based at 0
+    - x86/decoder: Add new TEST instruction pattern
+    - x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
+    - x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
+    - perf/x86/intel: Hide TSX events when RTM is not supported
+    - arm64: Implement arch-specific pte_access_permitted()
+    - ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
+    - ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
+    - uapi: fix linux/tls.h userspace compilation error
+    - uapi: fix linux/rxrpc.h userspace compilation errors
+    - MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
+    - MIPS: ralink: Fix MT7628 pinmux
+    - MIPS: ralink: Fix typo in mt7628 pinmux function
+    - net: mvneta: fix handling of the Tx descriptor counter
+    - nbd: wait uninterruptible for the dead timeout
+    - nbd: don't start req until after the dead connection logic
+    - PM / OPP: Add missing of_node_put(np)
+    - PCI/ASPM: Account for downstream device's Port Common_Mode_Restore_Time
+    - PCI/ASPM: Use correct capability pointer to program LTR_L1.2_THRESHOLD
+    - PCI: hv: Use effective affinity mask
+    - PCI: Set Cavium ACS capability quirk flags to assert RR/CR/SV/UF
+    - PCI: Apply Cavium ThunderX ACS quirk to more Root Ports
+    - ALSA: hda: Add Raven PCI ID
+    - dm integrity: allow unaligned bv_offset
+    - dm cache: fix race condition in the writeback mode overwrite_bio
+      optimisation
+    - dm crypt: allow unaligned bv_offset
+    - dm zoned: ignore last smaller runt zone
+    - dm mpath: remove annoying message of 'blk_get_request() returned -11'
+    - dm bufio: fix integer overflow when limiting maximum cache size
+    - ovl: Put upperdentry if ovl_check_origin() fails
+    - dm: allocate struct mapped_device with kvzalloc
+    - sched/rt: Simplify the IPI based RT balancing logic
+    - MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
+    - dm: fix race between dm_get_from_kobject() and __dm_destroy()
+    - dm: discard support requires all targets in a table support discards
+    - MIPS: Fix odd fp register warnings with MIPS64r2
+    - MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
+    - MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
+    - MIPS: Fix an n32 core file generation regset support regression
+    - MIPS: BCM47XX: Fix LED inversion for WRT54GSv1
+    - MIPS: math-emu: Fix final emulation phase for certain instructions
+    - rt2x00usb: mark device removed when get ENOENT usb error
+    - mm/z3fold.c: use kref to prevent page free/compact race
+    - autofs: don't fail mount for transient error
+    - nilfs2: fix race condition that causes file system corruption
+    - fscrypt: lock mutex before checking for bounce page pool
+    - eCryptfs: use after free in ecryptfs_release_messaging()
+    - libceph: don't WARN() if user tries to add invalid key
+    - bcache: check ca->alloc_thread initialized before wake up it
+    - fs: guard_bio_eod() needs to consider partitions
+    - fanotify: fix fsnotify_prepare_user_wait() failure
+    - isofs: fix timestamps beyond 2027
+    - btrfs: change how we decide to commit transactions during flushing
+    - f2fs: expose some sectors to user in inline data or dentry case
+    - NFS: Fix typo in nomigration mount option
+    - NFS: Revert "NFS: Move the flock open mode check into nfs_flock()"
+    - nfs: Fix ugly referral attributes
+    - NFS: Avoid RCU usage in tracepoints
+    - NFS: revalidate "." etc correctly on "open".
+    - nfsd: deal with revoked delegations appropriately
+    - rtlwifi: rtl8192ee: Fix memory leak when loading firmware
+    - rtlwifi: fix uninitialized rtlhal->last_suspend_sec time
+    - iwlwifi: fix firmware names for 9000 and A000 series hw
+    - md: fix deadlock error in recent patch.
+    - md: don't check MD_SB_CHANGE_CLEAN in md_allow_write
+    - Bluetooth: btqcomsmd: Add support for BD address setup
+    - md/bitmap: revert a patch
+    - fsnotify: clean up fsnotify_prepare/finish_user_wait()
+    - fsnotify: pin both inode and vfsmount mark
+    - fsnotify: fix pinning group in fsnotify_prepare_user_wait()
+    - ata: fixes kernel crash while tracing ata_eh_link_autopsy event
+    - ext4: fix interaction between i_size, fallocate, and delalloc after a crash
+    - ext4: prevent data corruption with inline data + DAX
+    - ext4: prevent data corruption with journaling + DAX
+    - ALSA: pcm: update tstamp only if audio_tstamp changed
+    - ALSA: usb-audio: Add sanity checks to FE parser
+    - ALSA: usb-audio: Fix potential out-of-bound access at parsing SU
+    - ALSA: usb-audio: Add sanity checks in v2 clock parsers
+    - ALSA: timer: Remove kernel warning at compat ioctl error paths
+    - ALSA: hda/realtek - Fix ALC275 no sound issue
+    - ALSA: hda: Fix too short HDMI/DP chmap reporting
+    - ALSA: hda - Fix yet remaining issue with vmaster 0dB initialization
+    - ALSA: hda/realtek - Fix ALC700 family no sound issue
+    - ASoC: sun8i-codec: Invert Master / Slave condition
+    - ASoC: sun8i-codec: Fix left and right channels inversion
+    - ASoC: sun8i-codec: Set the BCLK divider
+    - mfd: lpc_ich: Avoton/Rangeley uses SPI_BYT method
+    - fix a page leak in vhost_scsi_iov_to_sgl() error recovery
+    - 9p: Fix missing commas in mount options
+    - fs/9p: Compare qid.path in v9fs_test_inode
+    - net/9p: Switch to wait_event_killable()
+    - scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
+    - scsi: sd_zbc: Fix sd_zbc_read_zoned_characteristics()
+    - scsi: lpfc: fix pci hot plug crash in timer management routines
+    - scsi: lpfc: fix pci hot plug crash in list_add call
+    - scsi: lpfc: Fix crash receiving ELS while detaching driver
+    - scsi: lpfc: Fix FCP hba_wqidx assignment
+    - scsi: lpfc: Fix oops if nvmet_fc_register_targetport fails
+    - iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
+    - iscsi-target: Fix non-immediate TMR reference leak
+    - target: fix null pointer regression in core_tmr_drain_tmr_list
+    - target: fix buffer offset in core_scsi3_pri_read_full_status
+    - target: Fix QUEUE_FULL + SCSI task attribute handling
+    - target: Fix caw_sem leak in transport_generic_request_failure
+    - target: Fix quiese during transport_write_pending_qf endless loop
+    - target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
+    - mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
+    - mtd: nand: Export nand_reset() symbol
+    - mtd: nand: atmel: Actually use the PM ops
+    - mtd: nand: omap2: Fix subpage write
+    - mtd: nand: Fix writing mtdoops to nand flash.
+    - mtd: nand: mtk: fix infinite ECC decode IRQ issue
+    - mailbox: bcm-flexrm-mailbox: Fix FlexRM ring flush sequence
+    - p54: don't unregister leds when they are not initialized
+    - block: Fix a race between blk_cleanup_queue() and timeout handling
+    - raid1: prevent freeze_array/wait_all_barriers deadlock
+    - genirq: Track whether the trigger type has been set
+    - irqchip/gic-v3: Fix ppi-partitions lookup
+    - lockd: double unregister of inetaddr notifiers
+    - KVM: PPC: Book3S HV: Don't call real-mode XICS hypercall handlers if not
+      enabled
+    - KVM: nVMX: set IDTR and GDTR limits when loading L1 host state
+    - KVM: SVM: obey guest PAT
+    - kvm: vmx: Reinstate support for CPUs without virtual NMI
+    - dax: fix PMD faults on zero-length files
+    - dax: fix general protection fault in dax_alloc_inode
+    - SUNRPC: Fix tracepoint storage issues with svc_recv and svc_rqst_status
+    - clk: ti: dra7-atl-clock: fix child-node lookups
+    - libnvdimm, dimm: clear 'locked' status on successful DIMM enable
+    - libnvdimm, pfn: make 'resource' attribute only readable by root
+    - libnvdimm, namespace: fix label initialization to use valid seq numbers
+    - libnvdimm, region : make 'resource' attribute only readable by root
+    - libnvdimm, namespace: make 'resource' attribute only readable by root
+    - svcrdma: Preserve CB send buffer across retransmits
+    - IB/srpt: Do not accept invalid initiator port names
+    - IB/cm: Fix memory corruption in handling CM request
+    - IB/hfi1: Fix incorrect available receive user context count
+    - IB/srp: Avoid that a cable pull can trigger a kernel crash
+    - IB/core: Avoid crash on pkey enforcement failed in received MADs
+    - IB/core: Only maintain real QPs in the security lists
+    - NFC: fix device-allocation error return
+    - spi-nor: intel-spi: Fix broken software sequencing codes
+    - i40e: Use smp_rmb rather than read_barrier_depends
+    - igb: Use smp_rmb rather than read_barrier_depends
+    - igbvf: Use smp_rmb rather than read_barrier_depends
+    - ixgbevf: Use smp_rmb rather than read_barrier_depends
+    - i40evf: Use smp_rmb rather than read_barrier_depends
+    - fm10k: Use smp_rmb rather than read_barrier_depends
+    - ixgbe: Fix skb list corruption on Power systems
+    - parisc: Fix validity check of pointer size argument in new CAS
+      implementation
+    - powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
+    - powerpc/mm/radix: Fix crashes on Power9 DD1 with radix MMU and STRICT_RWX
+    - powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
+    - powerpc/signal: Properly handle return value from uprobe_deny_signal()
+    - powerpc/64s: Fix masking of SRR1 bits on instruction fault
+    - powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
+    - powerpc/64s/hash: Fix 512T hint detection to use >= 128T
+    - powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
+    - powerpc/64s/hash: Fix fork() with 512TB process address space
+    - powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
+    - media: Don't do DMA on stack for firmware upload in the AS102 driver
+    - media: rc: check for integer overflow
+    - media: rc: nec decoder should not send both repeat and keycode
+    - cx231xx-cards: fix NULL-deref on missing association descriptor
+    - media: v4l2-ctrl: Fix flags field on Control events
+    - media: venus: fix wrong size on dma_free
+    - media: venus: venc: fix bytesused v4l2_plane field
+    - media: venus: reimplement decoder stop command
+    - ARM64: dts: meson-gxl: Add alternate ARM Trusted Firmware reserved memory
+      zone
+    - iwlwifi: fix wrong struct for a000 device
+    - iwlwifi: add a new a000 device
+    - iwlwifi: pcie: sort IDs for the 9000 series for easier comparisons
+    - iwlwifi: add new cards for a000 series
+    - iwlwifi: add new cards for 8265 series
+    - iwlwifi: add new cards for 8260 series
+    - iwlwifi: fix PCI IDs and configuration mapping for 9000 series
+    - iwlwifi: mvm: support version 7 of the SCAN_REQ_UMAC FW command
+    - e1000e: Fix error path in link detection
+    - e1000e: Fix return value test
+    - e1000e: Separate signaling for link check/link up
+    - e1000e: Avoid receiver overrun interrupt bursts
+    - e1000e: fix buffer overrun while the I219 is processing DMA transactions
+    - Linux 4.14.3
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: s390/topology: don't inline cpu_to_node
+    - SAUCE: (noup) Update spl to 0.7.3-1ubuntu1, zfs to 0.7.3-1ubuntu1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 04 Dec 2017 09:08:07 -0600
+
+linux (4.14.0-10.12) bionic; urgency=low
+
+  * linux: 4.14.0-10.12 -proposed tracker (LP: #1734901)
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Enable the ACPI kernel debugger and acpidbg tool
+    - [Packaging] Include arch/arm64/kernel/ftrace-mod.o in headers package
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 28 Nov 2017 08:46:49 -0600
+
+linux (4.14.0-9.11) bionic; urgency=low
+
+  * linux: 4.14.0-9.11 -proposed tracker (LP: #1734728)
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: SAUCE: (noup) Update spl to 0.7.3-1ubuntu1, zfs to
+      0.7.3-1ubuntu1"
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 27 Nov 2017 12:44:48 -0600
+
+linux (4.14.0-8.10) bionic; urgency=low
+
+  * linux: 4.14.0-8.10 -proposed tracker (LP: #1734695)
+
+  * Bionic update to v4.14.2 stable release (LP: #1734694)
+    - bio: ensure __bio_clone_fast copies bi_partno
+    - af_netlink: ensure that NLMSG_DONE never fails in dumps
+    - vxlan: fix the issue that neigh proxy blocks all icmpv6 packets
+    - net: cdc_ncm: GetNtbFormat endian fix
+    - fealnx: Fix building error on MIPS
+    - net/sctp: Always set scope_id in sctp_inet6_skb_msgname
+    - ima: do not update security.ima if appraisal status is not INTEGRITY_PASS
+    - serial: omap: Fix EFR write on RTS deassertion
+    - serial: 8250_fintek: Fix finding base_port with activated SuperIO
+    - tpm-dev-common: Reject too short writes
+    - rcu: Fix up pending cbs check in rcu_prepare_for_idle
+    - mm/pagewalk.c: report holes in hugetlb ranges
+    - ocfs2: fix cluster hang after a node dies
+    - ocfs2: should wait dio before inode lock in ocfs2_setattr()
+    - ipmi: fix unsigned long underflow
+    - mm/page_alloc.c: broken deferred calculation
+    - mm/page_ext.c: check if page_ext is not prepared
+    - coda: fix 'kernel memory exposure attempt' in fsync
+    - ipmi: Prefer ACPI system interfaces over SMBIOS ones
+    - Linux 4.14.2
+
+  * Bionic update to v4.14.1 stable release (LP: #1734693)
+    - EDAC, sb_edac: Don't create a second memory controller if HA1 is not present
+    - dmaengine: dmatest: warn user when dma test times out
+    - media: imon: Fix null-ptr-deref in imon_probe
+    - media: dib0700: fix invalid dvb_detach argument
+    - crypto: dh - Fix double free of ctx->p
+    - crypto: dh - Don't permit 'p' to be 0
+    - crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
+    - crypto: brcm - Explicity ACK mailbox message
+    - USB: early: Use new USB product ID and strings for DbC device
+    - USB: usbfs: compute urb->actual_length for isochronous
+    - USB: Add delay-init quirk for Corsair K70 LUX keyboards
+    - usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
+    - USB: serial: metro-usb: stop I/O after failed open
+    - USB: serial: Change DbC debug device binding ID
+    - USB: serial: qcserial: add pid/vid for Sierra Wireless EM7355 fw update
+    - USB: serial: garmin_gps: fix I/O after failed probe and remove
+    - USB: serial: garmin_gps: fix memory leak on probe errors
+    - selftests/x86/protection_keys: Fix syscall NR redefinition warnings
+    - x86/MCE/AMD: Always give panic severity for UC errors in kernel context
+    - platform/x86: peaq-wmi: Add DMI check before binding to the WMI interface
+    - platform/x86: peaq_wmi: Fix missing terminating entry for peaq_dmi_table
+    - HID: cp2112: add HIDRAW dependency
+    - HID: wacom: generic: Recognize WACOM_HID_WD_PEN as a type of pen collection
+    - rpmsg: glink: Add missing MODULE_LICENSE
+    - staging: wilc1000: Fix bssid buffer offset in Txq
+    - staging: sm750fb: Fix parameter mistake in poke32
+    - staging: ccree: fix 64 bit scatter/gather DMA ops
+    - staging: greybus: spilib: fix use-after-free after deregistration
+    - staging: rtl8188eu: Revert 4 commits breaking ARP
+    - spi: fix use-after-free at controller deregistration
+    - sparc32: Add cmpxchg64().
+    - sparc64: mmu_context: Add missing include files
+    - sparc64: Fix page table walk for PUD hugepages
+    - Linux 4.14.1
+
+  * Set PANIC_TIMEOUT=10 on Power Systems (LP: #1730660)
+    - [Config]: Set PANIC_TIMEOUT=10 on ppc64el
+
+  * enable CONFIG_SND_SOC_INTEL_BYT_CHT_NOCODEC_MACH easily confuse users
+    (LP: #1732627)
+    - [Config] CONFIG_SND_SOC_INTEL_BYT_CHT_NOCODEC_MACH=n
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.7.3-1ubuntu1, zfs to 0.7.3-1ubuntu1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 27 Nov 2017 07:43:44 -0600
+
+linux (4.14.0-7.9) bionic; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: apparmor: add base infastructure for socket mediation
+    - SAUCE: apparmor: af_unix mediation
+    - SAUCE: LSM stacking: procfs: add smack subdir to attrs
+    - SAUCE: LSM stacking: LSM: manage credential security blobs
+    - SAUCE: LSM stacking: LSM: Manage file security blobs
+    - SAUCE: LSM stacking: LSM: manage task security blobs
+    - SAUCE: LSM stacking: LSM: Infrastructure management of the remaining blobs
+    - SAUCE: LSM stacking: LSM: general but not extreme module stacking
+    - SAUCE: LSM stacking: LSM: Complete task_alloc hook
+    - SAUCE: LSM stacking: fixup procsfs: add smack subdir to attrs
+    - SAUCE: LSM stacking: fixup initialize task->security
+    - SAUCE: LSM stacking: fixup: alloc_task_ctx is dead code
+    - SAUCE: LSM stacking: add support for stacking getpeersec_stream
+    - SAUCE: LSM stacking: add stacking support to apparmor network hooks
+    - SAUCE: LSM stacking: fixup apparmor stacking enablement
+    - SAUCE: LSM stacking: fixup stacking kconfig
+    - SAUCE: LSM stacking: allow selecting multiple LSMs using kernel boot params
+    - SAUCE: LSM stacking: provide prctl interface for setting context
+    - SAUCE: LSM stacking: inherit current display LSM
+    - SAUCE: LSM stacking: keep an index for each registered LSM
+    - SAUCE: LSM stacking: verify display LSM
+    - SAUCE: LSM stacking: provide a way to specify the default display lsm
+    - SAUCE: LSM stacking: make sure LSM blob align on 64 bit boundaries
+    - SAUCE: LSM stacking: add /proc/<pid>/attr/display_lsm
+    - SAUCE: LSM stacking: add Kconfig to set default display LSM
+    - SAUCE: LSM stacking: add configs for LSM stacking
+    - SAUCE: LSM stacking: check for invalid zero sized writes
+    - [Config] Run updateconfigs after merging LSM stacking
+    - [Config] CONFIG_AMD_MEM_ENCRYPT=y
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 13 Nov 2017 08:12:08 -0600
+
+linux (4.14.0-6.8) bionic; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: add workarounds to enable ZFS for 4.14
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14-rc8
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 06 Nov 2017 11:39:00 -0600
+
+linux (4.14.0-5.7) bionic; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Fix invocation of dh_prep for dbgsym packages
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 31 Oct 2017 07:07:23 -0500
+
+linux (4.14.0-4.5) bionic; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] virtualbox -- reduce in kernel module versions
+    - vbox-update: Fix up KERN_DIR definitions
+    - ubuntu: vbox -- update to 5.2.0-dfsg-2
+    - [Config] CONFIG_AMD_MEM_ENCRYPT=n
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 30 Oct 2017 13:29:20 -0500
+
+linux (4.14.0-3.4) artful; urgency=low
+
+  * Touchpad and TrackPoint Dose Not Work on Lenovo X1C6 and X280 (LP: #1723986)
+    - SAUCE: Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
+    - SAUCE: Input: synaptics - Lenovo X1 Carbon 5 should use SMBUS/RMI
+    - SAUCE: Input: synaptics - add Intertouch support on X1 Carbon 6th and X280
+
+  * powerpc/64s: Add workaround for P9 vector CI load issuenext (LP: #1721070)
+    - powerpc/64s: Add workaround for P9 vector CI load issue
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: staging: vboxvideo: Fix reporting invalid suggested-offset-properties
+    - [Config] CONFIG_DRM_VBOXVIDEO=m
+    - SAUCE: Import aufs driver
+    - [Config] Enable aufs
+    - [Config] Reorder annotations file after enabling aufs
+    - vbox-update: Disable imported vboxvideo module
+    - ubuntu: vbox -- update to 5.1.30-dfsg-1
+    - Enable vbox
+    - hio: Use correct sizes when initializing ssd_index_bits* arrays
+    - hio: Update io stat accounting for 4.14
+    - Enable hio
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14-rc5
+  * Rebase to v4.14-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 23 Oct 2017 13:53:52 -0500
+
+linux (4.14.0-2.3) artful; urgency=low
+
+  * [Bug] USB controller failed to respond on Denverton after loading
+    intel_th_pci module (LP: #1715833)
+    - SAUCE: PCI: Disable broken RTIT_BAR of Intel TH
+
+  * CONFIG_DEBUG_FS is not enabled by "make zfcpdump_defconfig" with Ubuntu
+    17.10 (kernel 4.13) (LP: #1719290)
+    - SAUCE: s390: update zfcpdump_defconfig
+
+  * Add installer support for Broadcom BCM573xx network drivers. (LP: #1720466)
+    - d-i: Add bnxt_en to nic-modules.
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update annotations for 4.14-rc2
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14-rc3
+  * Rebase to v4.14-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 11 Oct 2017 16:04:27 -0500
+
+linux (4.14.0-1.2) artful; urgency=low
+
+  * [Bug] USB 3.1 Gen2 works as 5Gbps (LP: #1720045)
+    - xhci: set missing SuperSpeedPlus Link Protocol bit in roothub descriptor
+
+  * Please make linux-libc-dev Provide: aufs-dev (LP: #1716091)
+    - [Packaging] Add aufs-dev to the Provides: for linux-libc-dev
+
+  * Upgrade to 4.13.0-11.12 in artful amd64 VM breaks display on wayland
+    (LP: #1718679)
+    - [Config] CONFIG_DRM_VBOXVIDEO=n
+
+  * ipmmu-vmsa driver breaks arm64 boots (LP: #1718734)
+    - [Config] Disable CONFIG_IPMMU_VMSA on arm64
+
+  * autopkgtest profile fails to build on armhf (LP: #1717920)
+    - [Packaging] autopkgtest -- disable d-i when dropping flavours
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_I2C_XLP9XX=m
+    - [Packaging] Use SRCPKGNAME rather than hard-coding the source package name
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 29 Sep 2017 09:09:11 -0400
+
+linux (4.14.0-0.1) artful; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - Disable vbox build
+    - Disable hio build
+    - Disable zfs build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.14-rc1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 19 Sep 2017 20:22:29 -0500
+
+linux (4.13.0-11.12) artful; urgency=low
+
+  * linux: 4.13.0-11.12 -proposed tracker (LP: #1716699)
+
+  * kernel panic -not syncing: Fatal exception: panic_on_oops (LP: #1708399)
+    - s390/mm: fix local TLB flushing vs. detach of an mm address space
+    - s390/mm: fix race on mm->context.flush_mm
+
+  * CVE-2017-1000251
+    - Bluetooth: Properly check L2CAP config option output buffer length
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 12 Sep 2017 10:18:38 -0500
+
+linux (4.13.0-10.11) artful; urgency=low
+
+  * linux: 4.13.0-10.11 -proposed tracker (LP: #1716287)
+
+  * please add aufs-dkms to the Provides: for the kernel packages (LP: #1716093)
+    - [Packaging] Add aufs-dkms to the Provides: for kernel packages
+
+  * Artful update to v4.13.1 stable release (LP: #1716284)
+    - usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard
+    - USB: serial: option: add support for D-Link DWM-157 C1
+    - usb: Add device quirk for Logitech HD Pro Webcam C920-C
+    - usb:xhci:Fix regression when ATI chipsets detected
+    - USB: musb: fix external abort on suspend
+    - ANDROID: binder: add padding to binder_fd_array_object.
+    - ANDROID: binder: add hwbinder,vndbinder to BINDER_DEVICES.
+    - USB: core: Avoid race of async_completed() w/ usbdev_release()
+    - staging/rts5208: fix incorrect shift to extract upper nybble
+    - staging: ccree: save ciphertext for CTS IV
+    - staging: fsl-dpaa2/eth: fix off-by-one FD ctrl bitmaks
+    - iio: adc: ti-ads1015: fix incorrect data rate setting update
+    - iio: adc: ti-ads1015: fix scale information for ADS1115
+    - iio: adc: ti-ads1015: enable conversion when CONFIG_PM is not set
+    - iio: adc: ti-ads1015: avoid getting stale result after runtime resume
+    - iio: adc: ti-ads1015: don't return invalid value from buffer setup callbacks
+    - iio: adc: ti-ads1015: add adequate wait time to get correct conversion
+    - driver core: bus: Fix a potential double free
+    - HID: wacom: Do not completely map WACOM_HID_WD_TOUCHRINGSTATUS usage
+    - binder: free memory on error
+    - crypto: caam/qi - fix compilation with CONFIG_DEBUG_FORCE_WEAK_PER_CPU=y
+    - crypto: caam/qi - fix compilation with DEBUG enabled
+    - thunderbolt: Fix reset response_type
+    - fpga: altera-hps2fpga: fix multiple init of l3_remap_lock
+    - intel_th: pci: Add Cannon Lake PCH-H support
+    - intel_th: pci: Add Cannon Lake PCH-LP support
+    - ath10k: fix memory leak in rx ring buffer allocation
+    - drm/vgem: Pin our pages for dmabuf exports
+    - drm/ttm: Fix accounting error when fail to get pages for pool
+    - drm/dp/mst: Handle errors from drm_atomic_get_private_obj_state() correctly
+    - rtlwifi: rtl_pci_probe: Fix fail path of _rtl_pci_find_adapter
+    - Bluetooth: Add support of 13d3:3494 RTL8723BE device
+    - iwlwifi: pci: add new PCI ID for 7265D
+    - dlm: avoid double-free on error path in dlm_device_{register,unregister}
+    - mwifiex: correct channel stat buffer overflows
+    - MCB: add support for SC31 to mcb-lpc
+    - s390/mm: avoid empty zero pages for KVM guests to avoid postcopy hangs
+    - drm/nouveau/pci/msi: disable MSI on big-endian platforms by default
+    - drm/nouveau: Fix error handling in nv50_disp_atomic_commit
+    - workqueue: Fix flag collision
+    - ahci: don't use MSI for devices with the silly Intel NVMe remapping scheme
+    - cs5536: add support for IDE controller variant
+    - scsi: sg: protect against races between mmap() and SG_SET_RESERVED_SIZE
+    - scsi: sg: recheck MMAP_IO request length with lock held
+    - of/device: Prevent buffer overflow in of_device_modalias()
+    - rtlwifi: Fix memory leak when firmware request fails
+    - rtlwifi: Fix fallback firmware loading
+    - Linux 4.13.1
+
+  * Kernel has trouble recognizing Corsair Strafe RGB keyboard (LP: #1678477)
+    - usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard
+
+  * SRIOV: warning if unload VFs (LP: #1715073)
+    - PCI: Disable VF decoding before pcibios_sriov_disable() updates resources
+
+  * [Patch] network-i40e:NVM bug fixes (cherrypick from 4.14) (LP: #1715578)
+    - i40e: avoid NVM acquire deadlock during NVM update
+    - i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
+
+  * [P9,POwer NV] Perf PMU event : pm_br_2path and pm_ld_miss_l1 is counted
+    twice when perf stat is done (perf:) (LP: #1714571)
+    - perf vendor events powerpc: Remove duplicate events
+
+  * Unable to install Ubuntu on the NVMe disk under VMD PCI domain
+    (LP: #1703339)
+    - [Config] Include vmd in storage-core-modules udeb
+
+  * 17.10 fails to boot on POWER9 DD2.0 with Deep stop states (LP: #1715064)
+    - powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle
+    - powerpc/powernv: Clear PECE1 in LPCR via stop-api only on Hotplug
+    - SAUCE: powerpc/powernv: Clear LPCR[PECE1] via stop-api only for deep state
+      offline
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: selftests/seccomp: Support glibc 2.26 siginfo_t.h
+    - Revert "UBUNTU: SAUCE: Import aufs driver"
+    - SAUCE: Import aufs driver
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 10 Sep 2017 17:48:59 -0500
+
+linux (4.13.0-9.10) artful; urgency=low
+
+  * linux: 4.13.0-9.10 -proposed tracker (LP: #1715145)
+
+  * EDAC sbridge: Failed to register device with error -22. (LP: #1714112)
+    - [Config] CONFIG_EDAC_GHES=n
+
+  * Miscellaneous Ubuntu changes
+    - ubuntu: vbox -- update to 5.1.26-dfsg-2
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 05 Sep 2017 07:51:19 -0500
+
+linux (4.13.0-8.9) artful; urgency=low
+
+  * snapd 2.27.3+17.10 ADT test failure with linux 4.13.0-6.7 (LP: #1713103)
+    - SAUCE: apparmor: fix apparmorfs DAC access, permissions
+
+  * enable ARCH_SUNXI (and friends) in arm64 kernel .config (LP: #1701137)
+    - [Config] Enable CONFIG_ARCH_SUNXI and related options for arm64
+
+  * [Bug] Harrisonville: pnd2_edac always fail to load on B1 stepping
+    Harrisonville SDP (LP: #1709257)
+    - EDAC, pnd2: Build in a minimal sideband driver for Apollo Lake
+    - EDAC, pnd2: Mask off the lower four bits of a BAR
+    - EDAC, pnd2: Conditionally unhide/hide the P2SB PCI device to read BAR
+    - EDAC, pnd2: Properly toggle hidden state for P2SB PCI device
+    - SAUCE: i2c: i801: Restore the presence state of P2SB PCI device after
+      reading BAR
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: SAUCE: Import aufs driver"
+    - SAUCE: Import aufs driver
+    - SAUCE: selftests/powerpc: Disable some ptrace selftests
+    - [Config] CONFIG_CRYPTO_DEV_NITROX_CNN55XX=n for s390x
+    - [Config] CONFIG_I2C_SLAVE=n for amd64, i386, ppc64el
+    - [Config] Disable CONFIG_MDIO_* options for s390x
+    - [Config] CONFIG_SCSI_MQ_DEFAULT=n for s390x
+    - [Config] Update annotations for 4.13
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 31 Aug 2017 14:27:09 -0500
+
+linux (4.13.0-7.8) artful; urgency=low
+
+  * linux 4.12.0-11.12 ADT test failure with linux 4.12.0-11.12 (LP: #1710904)
+    - SAUCE: selftests/powerpc: Use snprintf to construct DSCR sysfs interface
+      paths
+
+  * Miscellaneous Ubuntu changes
+    - Revert "UBUNTU: SAUCE: seccomp: log actions even when audit is disabled"
+
+  * Miscellaneous upstream changes
+    - seccomp: Provide matching filter for introspection
+    - seccomp: Sysctl to display available actions
+    - seccomp: Operation for checking if an action is available
+    - seccomp: Sysctl to configure actions that are allowed to be logged
+    - seccomp: Selftest for detection of filter flag support
+    - seccomp: Filter flag to log all actions except SECCOMP_RET_ALLOW
+    - seccomp: Action to log before allowing
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 28 Aug 2017 08:12:24 -0500
+
+linux (4.13.0-6.7) artful; urgency=low
+
+  * HID: multitouch: Support ALPS PTP Stick and Touchpad devices (LP: #1712481)
+    - SAUCE: HID: multitouch: Support ALPS PTP stick with pid 0x120A
+
+  * sort ABI files with C.UTF-8 locale (LP: #1712345)
+    - [Packaging] sort ABI files with C.UTF-8 locale
+
+  * igb: Support using Broadcom 54616 as PHY (LP: #1712024)
+    - SAUCE: igb: add support for using Broadcom 54616 as PHY
+
+  * RPT related fixes missing in Ubuntu 16.04.3 (LP: #1709220)
+    - powerpc/mm/radix: Improve _tlbiel_pid to be usable for PWC flushes
+    - powerpc/mm/radix: Improve TLB/PWC flushes
+    - powerpc/mm/radix: Avoid flushing the PWC on every flush_tlb_range
+
+  * Linux 4.12 refuses to load self-signed modules under Secure Boot with
+    properly enrolled keys (LP: #1712168)
+    - SAUCE: (efi-lockdown) MODSIGN: Fix module signature verification
+
+  * [17.10 FEAT] Enable NVMe driver - kernel (LP: #1708432)
+    - [Config] CONFIG_BLK_DEV_NVME=m for s390
+
+  * Artful: 4.12.0-11.12: Boot panic in vlv2_plat_configure_clock+0x3b/0xa0
+    (LP: #1711298)
+    - [Config] CONFIG_INTEL_ATOMISP=n
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: apparmor: af_unix mediation
+
+  * Miscellaneous upstream changes
+    - apparmor: Fix shadowed local variable in unpack_trans_table()
+    - apparmor: Fix logical error in verify_header()
+    - apparmor: Fix an error code in aafs_create()
+    - apparmor: Redundant condition: prev_ns. in [label.c:1498]
+    - apparmor: add the ability to mediate signals
+    - apparmor: add mount mediation
+    - apparmor: cleanup conditional check for label in label_print
+    - apparmor: add support for absolute root view based labels
+    - apparmor: make policy_unpack able to audit different info messages
+    - apparmor: add more debug asserts to apparmorfs
+    - apparmor: add base infastructure for socket mediation
+    - apparmor: move new_null_profile to after profile lookup fns()
+    - apparmor: fix race condition in null profile creation
+    - apparmor: ensure unconfined profiles have dfas initialized
+    - apparmor: fix incorrect type assignment when freeing proxies
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 23 Aug 2017 08:10:38 -0500
+
+linux (4.13.0-5.6) artful; urgency=low
+
+  * Ubuntu17.10 - perf: Update Power9 PMU event JSON files (LP: #1708630)
+    - perf pmu-events: Support additional POWER8+ PVR in mapfile
+    - perf vendor events: Add POWER9 PMU events
+    - perf vendor events: Add POWER9 PVRs to mapfile
+    - SAUCE: perf vendor events powerpc: remove suffix in mapfile
+    - SAUCE: perf vendor events powerpc: Update POWER9 events
+
+  * Disable CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE (LP: #1709171)
+    - [Config] CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE=n for ppc64el
+
+  * Please only recommend or suggest initramfs-tools | linux-initramfs-tool for
+    kernels able to boot without initramfs (LP: #1700972)
+    - [Debian] Don't depend on initramfs-tools
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Import aufs driver
+    - SAUCE: aufs -- Add missing argument to loop_switch() call
+    - [Config] Enable aufs
+    - SAUCE: (noup) Update spl to 0.6.5.11-ubuntu1, zfs to 0.6.5.11-1ubuntu3
+    - Enable zfs build
+    - SAUCE: powerpc: Always initialize input array when calling epapr_hypercall()
+    - [Packaging] switch up to debhelper 9
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 15 Aug 2017 09:24:16 -0500
+
+linux (4.13.0-4.5) artful; urgency=low
+
+  * Lenovo Yoga 910 Sensors (LP: #1708120)
+    - SAUCE: (no-up) HID: Add quirk for Lenovo Yoga 910 with ITE Chips
+
+  * Unable to install Ubuntu on the NVMe disk under VMD PCI domain
+    (LP: #1703339)
+    - [Config] Add vmd driver to generic inclusion list
+
+  * Set CONFIG_SATA_HIGHBANK=y on armhf (LP: #1703430)
+    - [Config] CONFIG_SATA_HIGHBANK=y
+
+  * Miscellaneous Ubuntu changes
+    - ubuntu: vbox -- update to 5.1.26-dfsg-1
+    - SAUCE: hio: Build fixes for 4.13
+    - Enable hio build
+    - SAUCE: (noup) Update spl to 0.6.5.11-1, zfs to 0.6.5.11-1ubuntu1
+    - [debian] use all rather than amd64 dkms debs for sync
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc4
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 08 Aug 2017 11:31:48 -0500
+
+linux (4.13.0-3.4) artful; urgency=low
+
+  * Adt tests of src:linux time out often on armhf lxc containers (LP: #1705495)
+    - [Packaging] tests -- reduce rebuild test to one flavour
+    - [Packaging] tests -- reduce rebuild test to one flavour -- use filter
+
+  * snapd 2.26.8+17.10 ADT test failure with linux 4.12.0-6.7 (LP: #1704158)
+    - SAUCE: virtio_net: Revert mergeable buffer handling rework
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 31 Jul 2017 10:08:16 -0500
+
+linux (4.13.0-2.3) artful; urgency=low
+
+  * Change CONFIG_IBMVETH to module (LP: #1704479)
+    - [Config] CONFIG_IBMVETH=m
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 24 Jul 2017 13:58:08 -0500
+
+linux (4.13.0-1.2) artful; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Support sphinx-based kernel documentation
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Thu, 20 Jul 2017 09:18:33 -0500
+
+linux (4.13.0-0.1) artful; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - Disable hio
+    - Disable zfs build
+    - ubuntu: vbox -- update to 5.1.24-dfsg-1
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.13-rc1
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 19 Jul 2017 15:09:31 -0500
+
+linux (4.12.0-7.8) artful; urgency=low
+
+  * ThunderX: soft lockup on 4.8+ kernels when running qemu-efi with vhost=on
+    (LP: #1673564)
+    - arm64: Add a facility to turn an ESR syndrome into a sysreg encoding
+    - KVM: arm/arm64: vgic-v3: Add accessors for the ICH_APxRn_EL2 registers
+    - KVM: arm64: Make kvm_condition_valid32() accessible from EL2
+    - KVM: arm64: vgic-v3: Add hook to handle guest GICv3 sysreg accesses at EL2
+    - KVM: arm64: vgic-v3: Add ICV_BPR1_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_IGRPEN1_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_IAR1_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_EOIR1_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_AP1Rn_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_HPPIR1_EL1 handler
+    - KVM: arm64: vgic-v3: Enable trapping of Group-1 system registers
+    - KVM: arm64: Enable GICv3 Group-1 sysreg trapping via command-line
+    - KVM: arm64: vgic-v3: Add ICV_BPR0_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_IGNREN0_EL1 handler
+    - KVM: arm64: vgic-v3: Add misc Group-0 handlers
+    - KVM: arm64: vgic-v3: Enable trapping of Group-0 system registers
+    - KVM: arm64: Enable GICv3 Group-0 sysreg trapping via command-line
+    - arm64: Add MIDR values for Cavium cn83XX SoCs
+    - arm64: Add workaround for Cavium Thunder erratum 30115
+    - KVM: arm64: vgic-v3: Add ICV_DIR_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_RPR_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_CTLR_EL1 handler
+    - KVM: arm64: vgic-v3: Add ICV_PMR_EL1 handler
+    - KVM: arm64: Enable GICv3 common sysreg trapping via command-line
+    - KVM: arm64: vgic-v3: Log which GICv3 system registers are trapped
+    - KVM: arm64: Log an error if trapping a read-from-write-only GICv3 access
+    - KVM: arm64: Log an error if trapping a write-to-read-only GICv3 access
+
+  * hns: under heavy load, NIC may fail and require reboot (LP: #1704146)
+    - net: hns: Bugfix for Tx timeout handling in hns driver
+
+  * New ACPI identifiers for ThunderX SMMU (LP: #1703437)
+    - iommu/arm-smmu: Plumb in new ACPI identifiers
+
+  * Transparent hugepages should default to enabled=madvise (LP: #1703742)
+    - SAUCE: use CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y as default
+
+  * Artful update to v4.12.1 stable release (LP: #1703858)
+    - driver core: platform: fix race condition with driver_override
+    - RDMA/uverbs: Check port number supplied by user verbs cmds
+    - usb: dwc3: replace %p with %pK
+    - USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
+    - usb: usbip: set buffer pointers to NULL after free
+    - Add USB quirk for HVR-950q to avoid intermittent device resets
+    - usb: Fix typo in the definition of Endpoint[out]Request
+    - USB: core: fix device node leak
+    - USB: serial: option: add two Longcheer device ids
+    - USB: serial: qcserial: new Sierra Wireless EM7305 device ID
+    - xhci: Limit USB2 port wake support for AMD Promontory hosts
+    - gfs2: Fix glock rhashtable rcu bug
+    - Add "shutdown" to "struct class".
+    - tpm: Issue a TPM2_Shutdown for TPM2 devices.
+    - tpm: fix a kernel memory leak in tpm-sysfs.c
+    - powerpc/powernv: Fix CPU_HOTPLUG=n idle.c compile error
+    - x86/uaccess: Optimize copy_user_enhanced_fast_string() for short strings
+    - sched/fair, cpumask: Export for_each_cpu_wrap()
+    - sched/core: Implement new approach to scale select_idle_cpu()
+    - sched/numa: Use down_read_trylock() for the mmap_sem
+    - sched/numa: Override part of migrate_degrades_locality() when idle balancing
+    - sched/fair: Simplify wake_affine() for the single socket case
+    - sched/numa: Implement NUMA node level wake_affine()
+    - sched/fair: Remove effective_load()
+    - sched/numa: Hide numa_wake_affine() from UP build
+    - xen: avoid deadlock in xenbus driver
+    - crypto: drbg - Fixes panic in wait_for_completion call
+    - Linux 4.12.1
+
+  * cxlflash update request in the Xenial SRU stream (LP: #1702521)
+    - scsi: cxlflash: Combine the send queue locks
+    - scsi: cxlflash: Update cxlflash_afu_sync() to return errno
+    - scsi: cxlflash: Reset hardware queue context via specified register
+    - scsi: cxlflash: Schedule asynchronous reset of the host
+    - scsi: cxlflash: Handle AFU sync failures
+    - scsi: cxlflash: Track pending scsi commands in each hardware queue
+    - scsi: cxlflash: Flush pending commands in cleanup path
+    - scsi: cxlflash: Add scsi command abort handler
+    - scsi: cxlflash: Create character device to provide host management interface
+    - scsi: cxlflash: Separate AFU internal command handling from AFU sync
+      specifics
+    - scsi: cxlflash: Introduce host ioctl support
+    - scsi: cxlflash: Refactor AFU capability checking
+    - scsi: cxlflash: Support LUN provisioning
+    - scsi: cxlflash: Support AFU debug
+    - scsi: cxlflash: Support WS16 unmap
+    - scsi: cxlflash: Remove zeroing of private command data
+    - scsi: cxlflash: Update TMF command processing
+    - scsi: cxlflash: Avoid double free of character device
+    - scsi: cxlflash: Update send_tmf() parameters
+    - scsi: cxlflash: Update debug prints in reset handlers
+
+  * make snap-pkg support (LP: #1700747)
+    - make snap-pkg support
+
+  * Quirk for non-compliant PCI bridge on HiSilicon D05 board (LP: #1698706)
+    - SAUCE: PCI: Support hibmc VGA cards behind a misbehaving HiSilicon bridge
+
+  * arm64: fix crash reading /proc/kcore (LP: #1702749)
+    - fs/proc: kcore: use kcore_list type to check for vmalloc/module address
+    - arm64: mm: select CONFIG_ARCH_PROC_KCORE_TEXT
+
+  * Opal and POWER9 DD2 (LP: #1702159)
+    - SAUCE: powerpc/powernv: Tell OPAL about our MMU mode on POWER9
+
+  * Data corruption with hio driver  (LP: #1701316)
+    - SAUCE: hio: Fix incorrect use of enum req_opf values
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.6.5.10-1, zfs to 0.6.5.10-1ubuntu2
+    - snapcraft.yaml: Sync with xenial
+    - [Config] CONFIG_CAVIUM_ERRATUM_30115=y
+
+  * Miscellaneous upstream changes
+    - Revert "UBUNTU: SAUCE: (efi-lockdown) efi: Add sysctls for secureboot and
+      MokSBState"
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 14 Jul 2017 15:25:41 -0500
+
+linux (4.12.0-6.7) artful; urgency=low
+
+  * update ENA driver to 1.2.0k from net-next (LP: #1701575)
+    - net: ena: change return value for unsupported features unsupported return
+      value
+    - net: ena: add hardware hints capability to the driver
+    - net: ena: change sizeof() argument to be the type pointer
+    - net: ena: add reset reason for each device FLR
+    - net: ena: add support for out of order rx buffers refill
+    - net: ena: allow the driver to work with small number of msix vectors
+    - net: ena: use napi_schedule_irqoff when possible
+    - net: ena: separate skb allocation to dedicated function
+    - net: ena: use lower_32_bits()/upper_32_bits() to split dma address
+    - net: ena: update driver's rx drop statistics
+    - net: ena: update ena driver to version 1.2.0
+
+  * APST gets enabled against explicit kernel option (LP: #1699004)
+    - nvme: explicitly disable APST on quirked devices
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: hio: Update to Huawei ES3000_V2 (2.1.0.40)
+    - SAUCE: hio updates for 4.12
+    - SAUCE: Enable hio build
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 05 Jul 2017 14:23:20 -0500
+
+linux (4.12.0-5.6) artful; urgency=low
+
+  * ERAT invalidate on context switch removal (LP: #1700819)
+    - powerpc: Only do ERAT invalidate on radix context switch on P9 DD1
+
+  * powerpc: Invalidate ERAT on powersave wakeup for POWER9 (LP: #1700521)
+    - SAUCE: powerpc: Invalidate ERAT on powersave wakeup for POWER9
+
+  * Miscellaneous Ubuntu changes
+    - d-i: Move qcom-emac from arm64 to shared nic-modules
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.12
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 03 Jul 2017 07:52:02 -0500
+
+linux (4.12.0-4.5) artful; urgency=low
+
+  * aacraid driver may return uninitialized stack data to userspace
+    (LP: #1700077)
+    - SAUCE: scsi: aacraid: Don't copy uninitialized stack memory to userspace
+
+  * KILLER1435-S[0489:e0a2] BT cannot search BT 4.0 device (LP: #1699651)
+    - Bluetooth: btusb: Add support for 0489:e0a2 QCA_ROME device
+
+  * AACRAID for power9 platform (LP: #1689980)
+    - scsi: aacraid: Remove __GFP_DMA for raw srb memory
+    - scsi: aacraid: Fix DMAR issues with iommu=pt
+    - scsi: aacraid: Added 32 and 64 queue depth for arc natives
+    - scsi: aacraid: Set correct Queue Depth for HBA1000 RAW disks
+    - scsi: aacraid: Remove reset support from check_health
+    - scsi: aacraid: Change wait time for fib completion
+    - scsi: aacraid: Log count info of scsi cmds before reset
+    - scsi: aacraid: Print ctrl status before eh reset
+    - scsi: aacraid: Using single reset mask for IOP reset
+    - scsi: aacraid: Rework IOP reset
+    - scsi: aacraid: Add periodic checks to see IOP reset status
+    - scsi: aacraid: Rework SOFT reset code
+    - scsi: aacraid: Rework aac_src_restart
+    - scsi: aacraid: Use correct function to get ctrl health
+    - scsi: aacraid: Make sure ioctl returns on controller reset
+    - scsi: aacraid: Enable ctrl reset for both hba and arc
+    - scsi: aacraid: Add reset debugging statements
+    - scsi: aacraid: Remove reference to Series-9
+    - scsi: aacraid: Update driver version to 50834
+
+  * hibmc driver does not include "pci:" prefix in bus ID (LP: #1698700)
+    - SAUCE: drm: hibmc: Use set_busid function from drm core
+
+  * HiSilicon D05: installer doesn't appear on VGA (LP: #1698954)
+    - d-i: Add hibmc-drm to kernel-image udeb
+
+  * Fix /proc/cpuinfo revision for POWER9 DD2 (LP: #1698844)
+    - SAUCE: powerpc: Fix /proc/cpuinfo revision for POWER9 DD2
+
+  * Miscellaneous Ubuntu changes
+    - [Config] CONFIG_SATA_MV=n and CONFIG_GENERIC_PHY=n for s390x
+    - [Config] CONFIG_ATA=n for s390x
+    - [Config] Update annotations for 4.12
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.12-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 26 Jun 2017 11:27:29 -0500
+
+linux (4.12.0-3.4) artful; urgency=low
+
+  * Miscellaneous upstream changes
+    - ufs: fix the logics for tail relocation
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.12-rc6
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 19 Jun 2017 14:50:39 -0500
+
+linux (4.12.0-2.3) artful; urgency=low
+
+  * CVE-2014-9900
+    - SAUCE: (no-up) net: Zeroing the structure ethtool_wolinfo in
+      ethtool_get_wol()
+
+  * System doesn't boot properly on Gigabyte AM4 motherboards (AMD Ryzen)
+    (LP: #1671360)
+    - pinctrl/amd: Use regular interrupt instead of chained
+
+  * extend-diff-ignore should use exact matches (LP: #1693504)
+    - [Packaging] exact extend-diff-ignore matches
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: efi: Don't print secure boot state from the efi stub
+    - ubuntu: vbox -- Update to 5.1.22-dfsg-1
+    - SAUCE: vbox fixes for 4.12
+    - Re-enable virtualbox build
+    - [Config] CONFIG_ORANGEFS_FS=m
+    - SAUCE: (noup) Update spl to 0.6.5.9-1ubuntu2, zfs to 0.6.5.9-5ubuntu7
+    - Enable zfs build
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.12-rc4
+  * Rebase to v4.12-rc5
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 11 Jun 2017 22:25:13 -0500
+
+linux (4.12.0-1.2) artful; urgency=low
+
+  * Enable Matrox driver for Ubuntu 16.04.3 (LP: #1693337)
+    - [Config] Enable CONFIG_DRM_MGAG200 as module
+
+  * Support low-pin-count devices on Hisilicon SoCs (LP: #1677319)
+    - [Config] CONFIG_LIBIO=y on arm64 only
+    - SAUCE: LIBIO: Introduce a generic PIO mapping method
+    - SAUCE: OF: Add missing I/O range exception for indirect-IO devices
+    - [Config] CONFIG_HISILICON_LPC=y
+    - SAUCE: LPC: Support the device-tree LPC host on Hip06/Hip07
+    - SAUCE: LIBIO: Support the dynamically logical PIO registration of ACPI host
+      I/O
+    - SAUCE: LPC: Add the ACPI LPC support
+    - SAUCE: PCI: Apply the new generic I/O management on PCI IO hosts
+    - SAUCE: PCI: Restore codepath for !CONFIG_LIBIO
+
+  * POWER9: Additional patches for TTY and CPU_IDLE (LP: #1674325)
+    - SAUCE: tty: Fix ldisc crash on reopened tty
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Add build-dep on libnuma-dev to enable 'perf bench numa'
+    - Rebase to v4.12-rc3
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.12-rc3
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Mon, 29 May 2017 20:56:29 -0500
+
+linux (4.12.0-0.1) artful; urgency=low
+
+  * please enable CONFIG_ARM64_LSE_ATOMICS (LP: #1691614)
+    - [Config] CONFIG_ARM64_LSE_ATOMICS=y
+
+  * [Regression] NUMA_BALANCING disabled on arm64 (LP: #1690914)
+    - [Config] CONFIG_NUMA_BALANCING{,_DEFAULT_ENABLED}=y on arm64
+
+  * exec'ing a setuid binary from a threaded program sometimes fails to setuid
+    (LP: #1672819)
+    - SAUCE: exec: ensure file system accounting in check_unsafe_exec is correct
+
+  * Miscellaneous Ubuntu changes
+    - Update find-missing-sauce.sh to compare to artful
+    - Update dropped.txt
+    - SAUCE: (efi-lockdown) efi: Add EFI_SECURE_BOOT bit
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/mem and /dev/kmem when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Add a sysrq option to exit secure boot mode
+    - SAUCE: (efi-lockdown) kexec: Disable at runtime if the kernel is locked down
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) kexec_file: Disable at runtime if securelevel has been
+      set
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) asus-wmi: Restrict debugfs interface when the kernel
+      is locked down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Enable cold boot attack mitigation
+    - SAUCE: (efi-lockdown) bpf: Restrict kernel image access functions when the
+      kernel is locked down
+    - SAUCE: (efi-lockdown) scsi: Lock down the eata driver
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) KEYS: Allow unrestricted boot-time addition of keys to
+      secondary keyring
+    - SAUCE: (efi-lockdown) efi: Add EFI signature data types
+    - SAUCE: (efi-lockdown) efi: Add an EFI signature blob parser
+    - SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI Secure Boot
+    - SAUCE: (efi-lockdown) MODSIGN: Allow the "db" UEFI variable to be suppressed
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) efi: Add secure_boot state and status bit for
+      MokSBState
+    - SAUCE: (efi-lockdown) efi: Add sysctls for secureboot and MokSBState
+    - [Config] Set values for UEFI secure boot lockdown options
+    - Disable virtualbox build
+    - Disable hio build
+    - SAUCE: securityfs: Replace CURRENT_TIME with current_time()
+    - Disable zfs build
+    - [Debian] Work out upstream tag for use with gen-auto-reconstruct
+    - SAUCE: Import aufs driver
+    - SAUCE: aufs -- Include linux/mm.h in fs/aufs/file.h
+    - [Config] Enable aufs
+    - SAUCE: perf callchain: Include errno.h on x86 unconditinally
+
+  [ Upstream Kernel Changes ]
+
+  * Rebase to v4.12-rc2
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Sun, 21 May 2017 23:44:44 -0500
+
+linux (4.11.0-3.8) artful; urgency=low
+
+  [ Seth Forshee ]
+
+  * Release Tracking Bug
+    - LP: #1690999
+
+  * apparmor_parser hangs indefinitely when called by multiple threads
+    (LP: #1645037)
+    - SAUCE: apparmor: fix lock ordering for mkdir
+
+  * apparmor leaking securityfs pin count (LP: #1660846)
+    - SAUCE: apparmor: fix leak on securityfs pin count
+
+  * apparmor reference count leak when securityfs_setup_d_inode\ () fails
+    (LP: #1660845)
+    - SAUCE: apparmor: fix reference count leak when securityfs_setup_d_inode()
+      fails
+
+  * apparmor not checking error if security_pin_fs() fails (LP: #1660842)
+    - SAUCE: apparmor: fix not handling error case when securityfs_pin_fs() fails
+
+  * libvirt profile is blocking global setrlimit despite having no rlimit rule
+    (LP: #1679704)
+    - SAUCE: apparmor: fix complain mode failure for rlimit mediation
+    - apparmor: update auditing of rlimit check to provide capability information
+
+  * apparmor: does not provide a way to detect policy updataes (LP: #1678032)
+    - SAUCE: apparmor: add policy revision file interface
+
+  * apparmor does not make support of query data visible (LP: #1678023)
+    - SAUCE: apparmor: add label data availability to the feature set
+
+  * apparmor query interface does not make supported query info available
+    (LP: #1678030)
+    - SAUCE: apparmor: add information about the query inteface to the feature set
+
+  * change_profile incorrect when using namespaces with a compound stack
+    (LP: #1677959)
+    - SAUCE: apparmor: fix label parse for stacked labels
+
+  * Regression in 4.4.0-65-generic causes very frequent system crashes
+    (LP: #1669611)
+    - apparmor: sync of apparmor 3.6+ (17.04)
+
+  * Artful update to 4.11.1 stable release (LP: #1690814)
+    - dm ioctl: prevent stack leak in dm ioctl call
+    - drm/sti: fix GDP size to support up to UHD resolution
+    - power: supply: lp8788: prevent out of bounds array access
+    - brcmfmac: Ensure pointer correctly set if skb data location changes
+    - brcmfmac: Make skb header writable before use
+    - sparc64: fix fault handling in NGbzero.S and GENbzero.S
+    - refcount: change EXPORT_SYMBOL markings
+    - net: macb: fix phy interrupt parsing
+    - tcp: fix access to sk->sk_state in tcp_poll()
+    - geneve: fix incorrect setting of UDP checksum flag
+    - bpf: enhance verifier to understand stack pointer arithmetic
+    - bpf, arm64: fix jit branch offset related to ldimm64
+    - tcp: fix wraparound issue in tcp_lp
+    - net: ipv6: Do not duplicate DAD on link up
+    - net: usb: qmi_wwan: add Telit ME910 support
+    - tcp: do not inherit fastopen_req from parent
+    - ipv4, ipv6: ensure raw socket message is big enough to hold an IP header
+    - rtnetlink: NUL-terminate IFLA_PHYS_PORT_NAME string
+    - ipv6: initialize route null entry in addrconf_init()
+    - ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
+    - tcp: randomize timestamps on syncookies
+    - bnxt_en: allocate enough space for ->ntp_fltr_bmap
+    - bpf: don't let ldimm64 leak map addresses on unprivileged
+    - net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
+    - f2fs: sanity check segment count
+    - xen/arm,arm64: fix xen_dma_ops after 815dd18 "Consolidate get_dma_ops..."
+    - xen: Revert commits da72ff5bfcb0 and 72a9b186292d
+    - block: get rid of blk_integrity_revalidate()
+    - Linux 4.11.1
+
+  * Module signing exclusion for staging drivers does not work properly
+    (LP: #1690908)
+    - SAUCE: Fix module signing exclusion in package builds
+
+  * perf: qcom: Add L3 cache PMU driver (LP: #1689856)
+    - [Config] CONFIG_QCOM_L3_PMU=y
+    - perf: qcom: Add L3 cache PMU driver
+
+  * No PMU support for ACPI-based arm64 systems (LP: #1689661)
+    - drivers/perf: arm_pmu: rework per-cpu allocation
+    - drivers/perf: arm_pmu: manage interrupts per-cpu
+    - drivers/perf: arm_pmu: split irq request from enable
+    - drivers/perf: arm_pmu: remove pointless PMU disabling
+    - drivers/perf: arm_pmu: define armpmu_init_fn
+    - drivers/perf: arm_pmu: fold init into alloc
+    - drivers/perf: arm_pmu: factor out pmu registration
+    - drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
+    - drivers/perf: arm_pmu: handle no platform_device
+    - drivers/perf: arm_pmu: rename irq request/free functions
+    - drivers/perf: arm_pmu: split cpu-local irq request/free
+    - drivers/perf: arm_pmu: move irq request/free into probe
+    - drivers/perf: arm_pmu: split out platform device probe logic
+    - arm64: add function to get a cpu's MADT GICC table
+    - [Config] CONFIG_ARM_PMU_ACPI=y
+    - drivers/perf: arm_pmu: add ACPI framework
+    - arm64: pmuv3: handle !PMUv3 when probing
+    - arm64: pmuv3: use arm_pmu ACPI framework
+
+  * Fix NVLINK2 TCE route (LP: #1690155)
+    - powerpc/powernv: Fix TCE kill on NVLink2
+
+  * CVE-2017-0605
+    - tracing: Use strlcpy() instead of strcpy() in __trace_find_cmdline()
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Restore powerpc arch to annotations file
+    - [Config] Disable runtime testing modules
+    - [Config] Disable drivers not needed on s390x
+    - [Config] Update annotations for 4.11
+    - [Config] updateconfigs after apparmor updates
+
+  * Miscellaneous upstream changes
+    - apparmor: use SHASH_DESC_ON_STACK
+    - apparmor: fix invalid reference to index variable of iterator line 836
+    - apparmor: fix parameters so that the permission test is bypassed at boot
+    - apparmor: Make path_max parameter readonly
+    - apparmorfs: Combine two function calls into one in aa_fs_seq_raw_abi_show()
+    - apparmorfs: Use seq_putc() in two functions
+    - apparmor: provide information about path buffer size at boot
+    - apparmor: add/use fns to print hash string hex value
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 16 May 2017 00:39:13 -0500
+
+linux (4.11.0-2.7) artful; urgency=low
+
+  * kernel-wedge fails in artful due to leftover squashfs-modules d-i files
+    (LP: #1688259)
+    - Remove squashfs-modules files from d-i
+    - [Config] as squashfs-modules is builtin kernel-image must Provides: it
+
+  * [Zesty] d-i: replace msm_emac with qcom_emac (LP: #1677297)
+    - Revert "UBUNTU: d-i: initrd needs msm_emac on amberwing platform."
+    - d-i: initrd needs qcom_emac on amberwing platform.
+
+  * update for V3 kernel bits and improved multiple fan slice support
+    (LP: #1470091)
+    - SAUCE: fan: tunnel multiple mapping mode (v3)
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: (noup) Update spl to 0.6.5.9-1ubuntu1, zfs to 0.6.5.9-5ubuntu5
+    - Enable zfs
+    - SAUCE: fan: add VXLAN implementation
+    - SAUCE: (efi-lockdown) efi: Add EFI_SECURE_BOOT bit
+    - SAUCE: (efi-lockdown) Add the ability to lock down access to the running
+      kernel image
+    - SAUCE: (efi-lockdown) efi: Lock down the kernel if booted in secure boot
+      mode
+    - SAUCE: (efi-lockdown) Enforce module signatures if the kernel is locked down
+    - SAUCE: (efi-lockdown) Restrict /dev/mem and /dev/kmem when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Add a sysrq option to exit secure boot mode
+    - SAUCE: (efi-lockdown) kexec: Disable at runtime if the kernel is locked down
+    - SAUCE: (efi-lockdown) Copy secure_boot flag in boot params across kexec
+      reboot
+    - SAUCE: (efi-lockdown) kexec_file: Disable at runtime if securelevel has been
+      set
+    - SAUCE: (efi-lockdown) hibernate: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) uswsusp: Disable when the kernel is locked down
+    - SAUCE: (efi-lockdown) PCI: Lock down BAR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) x86: Lock down IO port access when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) x86: Restrict MSR access when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) asus-wmi: Restrict debugfs interface when the kernel
+      is locked down
+    - SAUCE: (efi-lockdown) ACPI: Limit access to custom_method when the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Ignore acpi_rsdp kernel param when the kernel
+      has been locked down
+    - SAUCE: (efi-lockdown) acpi: Disable ACPI table override if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) acpi: Disable APEI error injection if the kernel is
+      locked down
+    - SAUCE: (efi-lockdown) Enable cold boot attack mitigation
+    - SAUCE: (efi-lockdown) bpf: Restrict kernel image access functions when the
+      kernel is locked down
+    - SAUCE: (efi-lockdown) scsi: Lock down the eata driver
+    - SAUCE: (efi-lockdown) Prohibit PCMCIA CIS storage when the kernel is locked
+      down
+    - SAUCE: (efi-lockdown) Lock down TIOCSSERIAL
+    - SAUCE: (efi-lockdown) Add EFI signature data types
+    - SAUCE: (efi-lockdown) Add an EFI signature blob parser and key loader.
+    - SAUCE: (efi-lockdown) KEYS: Add a system blacklist keyring
+    - SAUCE: (efi-lockdown) MODSIGN: Import certificates from UEFI Secure Boot
+    - SAUCE: (efi-lockdown) MODSIGN: Support not importing certs from db
+    - SAUCE: (efi-lockdown) MODSIGN: Don't try secure boot if EFI runtime is
+      disabled
+    - SAUCE: (efi-lockdown) efi: Sanitize boot_params in efi stub
+    - SAUCE: (efi-lockdown) efi: Add secure_boot state and status bit for
+      MokSBState
+    - SAUCE: (efi-lockdown) efi: Add sysctls for secureboot and MokSBState
+    - [Config] Set values for UEFI secure boot lockdown options
+    - Update dropped.txt
+
+  [ Upstream Kernel Changes ]
+
+  * rebase to v4.11
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Fri, 05 May 2017 07:43:14 -0500
+
+linux (4.11.0-1.6) artful; urgency=low
+
+  * Miscellaneous Ubuntu changes
+    - [Debian] Use default compression for all packages
+    - SAUCE: (namespace) block_dev: Support checking inode permissions in
+      lookup_bdev()
+    - SAUCE: (namespace) block_dev: Check permissions towards block device inode
+      when mounting
+    - SAUCE: (namespace) mtd: Check permissions towards mtd block device inode
+      when mounting
+    - SAUCE: (namespace) fs: Allow superblock owner to change ownership of inodes
+    - SAUCE: (namespace) fs: Don't remove suid for CAP_FSETID for userns root
+    - SAUCE: (namespace) fs: Allow superblock owner to access do_remount_sb()
+    - SAUCE: (namespace) capabilities: Allow privileged user in s_user_ns to set
+      security.* xattrs
+    - SAUCE: (namespace) fs: Allow CAP_SYS_ADMIN in s_user_ns to freeze and thaw
+      filesystems
+    - SAUCE: (namespace) fuse: Add support for pid namespaces
+    - SAUCE: (namespace) fuse: Support fuse filesystems outside of init_user_ns
+    - SAUCE: (namespace) fuse: Restrict allow_other to the superblock's namespace
+      or a descendant
+    - SAUCE: (namespace) fuse: Allow user namespace mounts
+    - SAUCE: (namespace) ext4: Add support for unprivileged mounts from user
+      namespaces
+    - SAUCE: (namespace) evm: Don't update hmacs in user ns mounts
+    - SAUCE: (namespace) ext4: Add module parameter to enable user namespace
+      mounts
+    - SAUCE: (namespace) block_dev: Forbid unprivileged mounting when device is
+      opened for writing
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Wed, 26 Apr 2017 10:08:29 -0500
+
+linux (4.11.0-0.5) artful; urgency=low
+
+  * [Hyper-V][SAUCE] pci-hyperv: Use only 16 bit integer for PCI domain
+    (LP: #1684971)
+    - SAUCE: pci-hyperv: Use only 16 bit integer for PCI domain
+
+  * [Hyper-V] Ubuntu 14.04.2 LTS Generation 2 SCSI Errors on VSS Based Backups
+    (LP: #1470250)
+    - SAUCE: Tools: hv: vss: Thaw the filesystem and continue after freeze fails
+
+  * Enable virtual scsi server driver for Power (LP: #1615665)
+    - SAUCE: Return TCMU-generated sense data to fabric module
+
+  * include/linux/security.h header syntax error with !CONFIG_SECURITYFS
+    (LP: #1630990)
+    - SAUCE: (no-up) include/linux/security.h -- fix syntax error with
+      CONFIG_SECURITYFS=n
+
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Import aufs driver
+    - [Config] Enable aufs
+    - [Debian] Add script to update virtualbox
+    - ubuntu: vbox -- Update to 5.1.20-dfsg-2
+    - Enable vbox
+    - SAUCE: aufs -- Include linux/mm.h in fs/aufs/file.h
+
+  [ Upstream Kernel Changes ]
+
+  * rebase to v4.11-rc8
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 25 Apr 2017 13:42:54 -0500
+
+linux (4.11.0-0.4) zesty; urgency=low
+
+  * POWER9: Improve performance on memory management (LP: #1681429)
+    - SAUCE: powerpc/mm/radix: Don't do page walk cache flush when doing full mm
+      flush
+    - SAUCE: powerpc/mm/radix: Remove unnecessary ptesync
+
+  * Miscellaneous Ubuntu changes
+    - find-missing-sauce.sh
+
+  [ Upstream Kernel Changes ]
+
+  * rebase to v4.11-rc7
+
+ -- Seth Forshee <seth.forshee@canonical.com>  Tue, 18 Apr 2017 08:19:43 -0500
+
+linux (4.11.0-0.3) zesty; urgency=low
+
+  * Disable CONFIG_HVC_UDBG on ppc64el (LP: #1680888)
+    - [Config] Disable CONFIG_HVC_UDBG on ppc64el
+
+  * smartpqi driver needed in initram disk and installer (LP: #1680156)
+    - [Config] Add smartpqi to d-i
+
+  * Disable CONFIG_SECURITY_SELINUX_DISABLE (LP: #1680315)
+    - [Config] CONFIG_SECURITY_SELINUX_DISABLE=n
+
+  * Miscellaneous Ubuntu changes
+    - [Config] flash-kernel should be a Breaks
+    - [Config] drop the info directory
+    - [Config] drop NOTES as obsolete
+    - [Config] drop changelog.historical as obsolete
+    - rebase to v4.11-rc6
+
+  [ Upstream Kernel Changes ]
+
+  * rebase to v4.11-rc6
+
+ -- Tim Gardner <tim.gardner@canonical.com>  Tue, 11 Apr 2017 07:16:52 -0600
+
+linux (4.11.0-0.2) zesty; urgency=low
+
+  [ Upstream Kernel Changes ]
+
+  * rebase to v4.11-rc5
+
+ -- Tim Gardner <tim.gardner@canonical.com>  Mon, 03 Apr 2017 08:26:07 +0100
+
+linux (4.11.0-0.1) zesty; urgency=low
+
+  [ Upstream Kernel Changes ]
+
+  * rebase to v4.11-rc4
+    - LP: #1591053
+
+ -- Tim Gardner <tim.gardner@canonical.com>  Mon, 20 Mar 2017 05:15:32 -0600
+
+linux (4.11.0-0.0) zesty; urgency=low
+
+  * dummy entry
+
+ -- Tim Gardner <tim.gardner@canonical.com>  Mon, 20 Mar 2017 05:15:32 -0600
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/config/README.rst
+++ linux-xilinx-zynqmp-5.15.0/debian.master/config/README.rst
@@ -0,0 +1,185 @@
+==================
+Config Annotations
+==================
+
+:Author: Andrea Righi
+
+Overview
+========
+
+Each Ubuntu kernel needs to maintain its own .config for each supported
+architecture and each flavour.
+
+Every time a new patch is applied or a kernel is rebased on top of a new
+one, we need to update the .config's accordingly (config options can be
+added, removed and also renamed).
+
+So, we need to make sure that some critical config options are always
+matching the desired value in order to have a functional kernel.
+
+State of the art
+================
+
+At the moment configs are maintained as a set of Kconfig chunks (inside
+`debian.<kernel>/config/`): a global one, plus per-arch / per-flavour
+chunks.
+
+In addition to that, we need to maintain also a file called
+'annotations'; the purpose of this file is to make sure that some
+critical config options are not silently removed or changed when the
+real .config is re-generated (for example after a rebase or after
+applying a new set of patches).
+
+The main problem with this approach is that, often, we have duplicate
+information that is stored both in the Kconfig chunks *and* in the
+annotations files and, at the same time, the whole .config's information
+is distributed between Kconfig chunks and annotations, making it hard to
+maintain, review and manage in general.
+
+Proposed solution
+=================
+
+The proposed solution is to store all the config information into the
+"annotations" format and get rid of the config chunks (basically the
+real .config's can be produced "compiling" annotations).
+
+Implementation
+==============
+
+To help the management of the annotations an helper script is provided
+(`debian/scripts/misc/annotations`):
+
+```
+usage: annotations [-h] [--version] [--file FILE] [--arch ARCH] [--flavour FLAVOUR] [--config CONFIG]
+                   (--query | --export | --import FILE | --update FILE | --check FILE)
+
+Manage Ubuntu kernel .config and annotations
+
+options:
+  -h, --help            show this help message and exit
+  --version, -v         show program's version number and exit
+  --file FILE, -f FILE  Pass annotations or .config file to be parsed
+  --arch ARCH, -a ARCH  Select architecture
+  --flavour FLAVOUR, -l FLAVOUR
+                        Select flavour (default is "generic")
+  --config CONFIG, -c CONFIG
+                        Select a specific config option
+
+Action:
+  --query, -q           Query annotations
+  --export, -e          Convert annotations to .config format
+  --import FILE, -i FILE
+                        Import a full .config for a specific arch and flavour into annotations
+  --update FILE, -u FILE
+                        Import a partial .config into annotations (only resync configs specified in FILE)
+  --check FILE, -k FILE
+                        Validate kernel .config with annotations
+```
+
+This script allows to query config settings (per arch/flavour/config),
+export them into the Kconfig format (generating the real .config files)
+and check if the final .config matches the rules defined in the
+annotations.
+
+Examples (annotations is defined as an alias to `debian/scripts/annotations`):
+
+ - Show settings for `CONFIG_DEBUG_INFO_BTF` for master kernel across all the
+   supported architectures and flavours:
+
+```
+$ annotations --query --config CONFIG_DEBUG_INFO_BTF
+{
+    "policy": {
+        "amd64": "y",
+        "arm64": "y",
+        "armhf": "n",
+        "ppc64el": "y",
+        "riscv64": "y",
+        "s390x": "y"
+    },
+    "note": "'Needs newer pahole for armhf'"
+}
+```
+
+ - Dump kernel .config for arm64 and flavour generic-64k:
+
+```
+$ annotations --arch arm64 --flavour generic-64k --export
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_COMPAT=y
+...
+```
+
+ - Update annotations file with a new kernel .config for amd64 flavour
+   generic:
+
+```
+$ annotations --arch amd64 --flavour generic --import build/.config
+```
+
+Moreover, an additional kernelconfig commands are provided
+(via debian/rules targets):
+ - `migrateconfigs`: automatically merge all the previous configs into
+   annotations (local changes still need to be committed)
+
+Annotations headers
+===================
+
+The main annotations file should contain a header to define the architectures
+and flavours that are supported.
+
+Here is the format of the header for the generic kernel:
+```
+# Menu: HEADER
+# FORMAT: 4
+# ARCH: amd64 arm64 armhf ppc64el riscv64 s390x
+# FLAVOUR: amd64-generic arm64-generic arm64-generic-64k armhf-generic armhf-generic-lpae ppc64el-generic riscv64-generic s390x-generic
+
+```
+
+Example header of a derivative (linux-aws):
+```
+# Menu: HEADER
+# FORMAT: 4
+# ARCH: amd64 arm64
+# FLAVOUR: amd64-aws arm64-aws
+# FLAVOUR_DEP: {'amd64-aws': 'amd64-generic', 'arm64-aws': 'arm64-generic'}
+
+include "../../debian.master/config/annotations"
+
+# Below you can define only the specific linux-aws configs that differ from linux generic
+
+```
+
+Pros and Cons
+=============
+
+ Pros:
+  - avoid duplicate information in .config's and annotations
+  - allow to easily define groups of config settings (for a specific
+    environment or feature, such as annotations.clouds, annotations.ubuntu,
+    annotations.snapd, etc.)
+  - config options are more accessible, easy to change and review
+  - we can easily document how config options are managed (and external
+    contributors won't be discouraged anymore when they need to to change a
+    config option)
+
+ Cons:
+  - potential regressions: the new tool/scripts can have potential bugs,
+    so we could experience regressions due to some missed config changes
+  - kernel team need to understand the new process (even if everything
+    is transparent, kernel cranking process is the same, there might be
+    corner cases that need to be addressed and resolved manually)
+
+TODO
+====
+
+ - Migrate all flavour and arch definitions into annotations (rather
+   than having this information defined in multiple places inside
+   debian/scripts); right now this information is "partially" migrated,
+   meaning that we need to define arches and flavours in the headers
+   section of annotations (so that the annotations tool can figure out
+   the list of supported arches and flavours), but arches and flavours
+   are still defined elsewhere, ideally we would like to have arches and
+   flavours defined only in one place: annotations.
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/config/annotations
+++ linux-xilinx-zynqmp-5.15.0/debian.master/config/annotations
@@ -0,0 +1,14146 @@
+# Menu: HEADER
+# FORMAT: 4
+# ARCH: amd64 arm64 armhf ppc64el s390x
+# FLAVOUR: amd64-generic amd64-lowlatency arm64-generic arm64-generic-64k arm64-lowlatency arm64-lowlatency-64k armhf-generic armhf-generic-lpae ppc64el-generic s390x-generic
+
+CONFIG_ACCESSIBILITY                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_ACCESSIBILITY                            note<'LP: #1967702'>
+
+CONFIG_ACPI_CUSTOM_DSDT_FILE                    policy<{'amd64': '""'}>
+CONFIG_ACPI_CUSTOM_DSDT_FILE                    note<'might allow hardware damage'>
+
+CONFIG_ACPI_CUSTOM_METHOD                       policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_ACPI_CUSTOM_METHOD                       note<'SECURITY: allows arbitrary execution'>
+
+CONFIG_AGP                                      policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_AGP                                      note<'not autoloadable'>
+
+CONFIG_ARCH_ROCKCHIP                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_ROCKCHIP                            note<'LP:1566283 / LP:1825222'>
+
+CONFIG_ARM64_ERRATUM_843419                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_843419                     note<'LP:1647793'>
+
+CONFIG_ARM64_ERRATUM_858921                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_858921                     note<'LP#1675509'>
+
+CONFIG_ARM64_USE_LSE_ATOMICS                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_USE_LSE_ATOMICS                    note<'LP:1691614'>
+
+CONFIG_ARM64_VA_BITS_48                         policy<{'arm64': 'y'}>
+CONFIG_ARM64_VA_BITS_48                         note<'Cavium ThunderX 2-socket needs a minimum of 41 bits of VA'>
+
+CONFIG_ARMV8_DEPRECATED                         policy<{'arm64': 'y'}>
+CONFIG_ARMV8_DEPRECATED                         note<'LP:1545542'>
+
+CONFIG_ARM_HIGHBANK_CPUIDLE                     policy<{'armhf-generic': 'n', 'armhf-generic-lpae': 'y'}>
+CONFIG_ARM_HIGHBANK_CPUIDLE                     note<'broken on ecx-1000'>
+
+CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT       policy<{'arm64': 'n'}>
+CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT       note<'LP:1845820'>
+
+CONFIG_ASYMMETRIC_KEY_TYPE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ASYMMETRIC_KEY_TYPE                      note<'module signing'>
+
+CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE            note<'module signing'>
+
+CONFIG_ATA_PIIX                                 policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATA_PIIX                                 note<'LP:1627324'>
+
+CONFIG_BINFMT_SCRIPT                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BINFMT_SCRIPT                            note<'required if init is a shell script such as in initramfs-tools'>
+
+CONFIG_BLK_DEV_DM                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_DM                               note<'LP:#560717'>
+
+CONFIG_BLK_DEV_NVME                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_NVME                             note<'LP:#1759893'>
+
+CONFIG_BLK_DEV_RAM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_RAM                              note<'LP #1593293'>
+
+CONFIG_BLK_DEV_RAM_SIZE                         policy<{'amd64': '65536', 'arm64': '65536', 'armhf': '65536', 'ppc64el': '65536', 's390x': '65536'}>
+CONFIG_BLK_DEV_RAM_SIZE                         note<'Ramdisk size should be a minimum of 64M'>
+
+CONFIG_BLK_DEV_SD                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_SD                               note<'LP:1627330'>
+
+CONFIG_BLK_DEV_SR                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_SR                               note<'LP:1627330'>
+
+CONFIG_BLK_DEV_THROTTLING                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_THROTTLING                       note<'CGROUP disk consumption control'>
+
+CONFIG_BPF_UNPRIV_DEFAULT_OFF                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_UNPRIV_DEFAULT_OFF                   note<'security reason'>
+
+CONFIG_BT_HS                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BT_HS                                    note<'https://www.intel.com/content/www/us/en/security-center/advisory/intel-sa-00435.html'>
+
+CONFIG_CHR_DEV_SG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CHR_DEV_SG                               note<'not autoloadable'>
+
+CONFIG_CMA                                      policy<{'amd64': 'n', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CMA                                      note<'LP:1803206'>
+
+CONFIG_CMA_SIZE_MBYTES                          policy<{'arm64': '32', 'armhf': '32'}>
+CONFIG_CMA_SIZE_MBYTES                          note<'LP:1823753'>
+
+CONFIG_COMPAT_BRK                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_COMPAT_BRK                               note<'disables brk ASLR'>
+
+CONFIG_CP15_BARRIER_EMULATION                   policy<{'arm64': 'y'}>
+CONFIG_CP15_BARRIER_EMULATION                   note<'LP:1545542'>
+
+CONFIG_CPUFREQ_DT                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPUFREQ_DT                               note<'not autoloadable'>
+
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE         note<'for bootspeed'>
+
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE                note<'not autoloadable'>
+
+CONFIG_CPU_FREQ_GOV_ONDEMAND                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_ONDEMAND                    note<'not autoloadable'>
+
+CONFIG_CPU_FREQ_GOV_PERFORMANCE                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_PERFORMANCE                 note<'not autoloadable'>
+
+CONFIG_CPU_FREQ_GOV_POWERSAVE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_POWERSAVE                   note<'not autoloadable'>
+
+CONFIG_CPU_FREQ_GOV_USERSPACE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_USERSPACE                   note<'not autoloadable'>
+
+CONFIG_CPU_FREQ_STAT                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_STAT                            note<'dependancy of boot essential'>
+
+CONFIG_CRASH_DUMP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRASH_DUMP                               note<'LP:1363180'>
+
+CONFIG_CRYPTO_SHA512                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SHA512                            note<'module signing'>
+
+CONFIG_CRYPTO_USER_API_ENABLE_OBSOLETE          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRYPTO_USER_API_ENABLE_OBSOLETE          note<'Obsolete w/ no known userspace dependencies'>
+
+CONFIG_DEBUG_FS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_FS                                 note<'required debug option'>
+
+CONFIG_DEBUG_INFO                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_INFO                               note<'required for debug packages'>
+
+CONFIG_DEBUG_INFO_BTF                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_INFO_BTF                           note<'Needs newer pahole for armhf'>
+
+CONFIG_DEBUG_INFO_SPLIT                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_INFO_SPLIT                         note<'LP:1413646 and LP:1413664'>
+
+CONFIG_DEBUG_KERNEL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_KERNEL                             note<'required debug option'>
+
+CONFIG_DEFAULT_MMAP_MIN_ADDR                    policy<{'amd64': '65536', 'arm64': '32768', 'armhf': '32768', 'ppc64el': '65536', 's390x': '65536'}>
+CONFIG_DEFAULT_MMAP_MIN_ADDR                    note<'LP:1418140 LP:1531327'>
+
+CONFIG_DEVTMPFS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEVTMPFS                                 note<'upstart requirement'>
+
+CONFIG_DEVTMPFS_MOUNT                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEVTMPFS_MOUNT                           note<'upstart requirement'>
+
+CONFIG_DMA_CMA                                  policy<{'arm64': 'y', 'armhf': 'y', 's390x': 'n'}>
+CONFIG_DMA_CMA                                  note<'LP:1803206'>
+
+CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG_SECONDARY_KEYRING policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG_SECONDARY_KEYRING note<'LP: #2019040'>
+
+CONFIG_DRM_AMDGPU_CIK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMDGPU_CIK                           note<'LP:1661887 for zesty'>
+
+CONFIG_DRM_HISI_HIBMC                           policy<{'arm64': 'm'}>
+CONFIG_DRM_HISI_HIBMC                           note<'LP:1762940'>
+
+CONFIG_DRM_LEGACY                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DRM_LEGACY                               note<'Consider re-enabling but not signing the modules'>
+
+CONFIG_DRM_MGAG200                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_MGAG200                              note<'LP#1693337'>
+
+CONFIG_DRM_STI                                  policy<{'armhf': 'n'}>
+CONFIG_DRM_STI                                  note<'LP#1398458'>
+
+CONFIG_DRM_VBOXVIDEO                            policy<{'amd64': 'm'}>
+CONFIG_DRM_VBOXVIDEO                            note<'LP:1718679'>
+
+CONFIG_DVB_DUMMY_FE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DUMMY_FE                             note<'expert use only'>
+
+CONFIG_ECRYPT_FS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ECRYPT_FS                                note<'not autoloadable'>
+
+CONFIG_EFIVAR_FS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFIVAR_FS                                note<'needed for variable EFI update'>
+
+CONFIG_EFI_VARS                                 policy<{'amd64': 'y'}>
+CONFIG_EFI_VARS                                 note<'EFI boot requirement (d-i) LP:#837332'>
+
+CONFIG_EVM                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EVM                                      note<'LP:1643652'>
+
+CONFIG_EVM_ATTR_FSUUID                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EVM_ATTR_FSUUID                          note<'LP:1643652'>
+
+CONFIG_EVM_LOAD_X509                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_EVM_LOAD_X509                            note<'LP:1643652'>
+
+CONFIG_EVM_X509_PATH                            policy<{'ppc64el': '"/etc/keys/x509_evm.der"'}>
+CONFIG_EVM_X509_PATH                            note<'LP:1643652'>
+
+CONFIG_EXT2_FS                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_EXT2_FS                                  note<'ext4 handling via EXT4_USE_FOR_EXT23'>
+
+CONFIG_EXT3_FS                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_EXT3_FS                                  note<'ext4 handling via EXT4_USE_FOR_EXT23'>
+
+CONFIG_FA_DUMP                                  policy<{'ppc64el': 'y'}>
+CONFIG_FA_DUMP                                  note<'LP:1415562'>
+
+CONFIG_FHANDLE                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FHANDLE                                  note<'LP:1412543'>
+
+CONFIG_FUSE_FS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUSE_FS                                  note<'not autoloadable'>
+
+CONFIG_FW_LOADER_COMPRESS_ZSTD                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FW_LOADER_COMPRESS_ZSTD                  note<'LP: #2028550'>
+
+CONFIG_FW_LOADER_USER_HELPER_FALLBACK           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FW_LOADER_USER_HELPER_FALLBACK           note<'LP#1398458'>
+
+CONFIG_GPIO_CDEV_V1                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GPIO_CDEV_V1                             note<'LP: #1953613'>
+
+CONFIG_GPIO_EM                                  policy<{'armhf': 'n'}>
+CONFIG_GPIO_EM                                  note<'h/w not encounted'>
+
+CONFIG_GPIO_TWL4030                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_GPIO_TWL4030                             note<'LP:#921934'>
+
+CONFIG_HIBERNATION                              policy<{'amd64': 'y', 'arm64': 'n', 'armhf': 'y', 'ppc64el': 'n'}>
+CONFIG_HIBERNATION                              note<'LP:1867753'>
+
+CONFIG_HIPPI                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HIPPI                                    note<'DEPRECATED'>
+
+CONFIG_HOTPLUG_PCI_PCIE                         policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HOTPLUG_PCI_PCIE                         note<'LP#1374440'>
+
+CONFIG_HOTPLUG_PCI_SHPC                         policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HOTPLUG_PCI_SHPC                         note<'LP#1374440'>
+
+CONFIG_HVC_UDBG                                 policy<{'ppc64el': 'n'}>
+CONFIG_HVC_UDBG                                 note<'LP#1680888'>
+
+CONFIG_I2C_CHARDEV                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_I2C_CHARDEV                              note<'LP:1417032'>
+
+CONFIG_IBMVNIC                                  policy<{'ppc64el': 'm'}>
+CONFIG_IBMVNIC                                  note<'LP:#1628187'>
+
+CONFIG_IDLE_PAGE_TRACKING                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IDLE_PAGE_TRACKING                       note<'is there a cost associated with this?'>
+
+CONFIG_IIO_SIMPLE_DUMMY_BUFFER                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IIO_SIMPLE_DUMMY_BUFFER                  note<'dummy driver'>
+
+CONFIG_IIO_SIMPLE_DUMMY_EVENTS                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IIO_SIMPLE_DUMMY_EVENTS                  note<'dummy driver'>
+
+CONFIG_IMA                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA                                      note<'LP:1643652'>
+
+CONFIG_IMA_APPRAISE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA_APPRAISE                             note<'LP:1643652'>
+
+CONFIG_IMA_ARCH_POLICY                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_IMA_ARCH_POLICY                          note<'LP:1866909'>
+
+CONFIG_IMA_DEFAULT_HASH_SHA256                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_IMA_DEFAULT_HASH_SHA256                  note<'LP:1643652'>
+
+CONFIG_IMA_KEXEC                                policy<{'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_IMA_KEXEC                                note<'LP:1643652'>
+
+CONFIG_IMA_KEYRINGS_PERMIT_SIGNED_BY_BUILTIN_OR_SECONDARY policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_KEYRINGS_PERMIT_SIGNED_BY_BUILTIN_OR_SECONDARY note<'LP:1667490'>
+
+CONFIG_IMA_READ_POLICY                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_IMA_READ_POLICY                          note<'LP:1866909'>
+
+CONFIG_IMA_SIG_TEMPLATE                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_IMA_SIG_TEMPLATE                         note<'LP:1643652'>
+
+CONFIG_IMA_WRITE_POLICY                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_WRITE_POLICY                         note<'LP:1667490'>
+
+CONFIG_INPUT_UINPUT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_INPUT_UINPUT                             note<'LP:584812'>
+
+CONFIG_INTEGRITY_PLATFORM_KEYRING               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTEGRITY_PLATFORM_KEYRING               note<'Required for lockdown'>
+
+CONFIG_INTEL_IOMMU_DEFAULT_ON                   policy<{'amd64': 'n'}>
+CONFIG_INTEL_IOMMU_DEFAULT_ON                   note<'LP: #1971699'>
+
+CONFIG_IOMMU_DEBUGFS                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IOMMU_DEBUGFS                            note<'Should not be enabled in production, LP #1861057'>
+
+CONFIG_IPDDP                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IPDDP                                    note<'LP:1559772'>
+
+CONFIG_IPMMU_VMSA                               policy<{'arm64': 'n', 'armhf': 'y'}>
+CONFIG_IPMMU_VMSA                               note<'LP:1718734'>
+
+CONFIG_IPV6                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6                                     note<'if this is a module we get a module load for every ipv6 packet'>
+
+CONFIG_IP_PNP                                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IP_PNP                                   note<'LP:1259861'>
+
+CONFIG_ISM                                      policy<{'s390x': 'm'}>
+CONFIG_ISM                                      note<'LP:1789934'>
+
+CONFIG_KERNEL_ZSTD                              policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_KERNEL_ZSTD                              note<'LP:#1931725'>
+
+CONFIG_KEXEC_BZIMAGE_VERIFY_SIG                 policy<{'amd64': 'y'}>
+CONFIG_KEXEC_BZIMAGE_VERIFY_SIG                 note<'Q: check this is in sync with the kexec/kdump userspace'>
+
+CONFIG_KFENCE_STATIC_KEYS                       policy<{'amd64': 'n', 'arm64': 'n', 's390x': 'n'}>
+CONFIG_KFENCE_STATIC_KEYS                       note<'LP:1948038'>
+
+CONFIG_KGDB_SERIAL_CONSOLE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_KGDB_SERIAL_CONSOLE                      note<'early debugging support'>
+
+CONFIG_KVM                                      policy<{'amd64': 'm', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KVM                                      note<'LP:1532886'>
+
+CONFIG_LATENCYTOP                               policy<{'amd64': 'n', 'amd64-lowlatency': 'y', 'arm64': 'n', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LATENCYTOP                               note<'https://lists.ubuntu.com/archives/kernel-team/2014-July/045006.html, LP#1655986'>
+
+CONFIG_LOAD_PPC_KEYS                            policy<{'ppc64el': 'y'}>
+CONFIG_LOAD_PPC_KEYS                            note<'LP:1866909'>
+
+CONFIG_LOCALVERSION_AUTO                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOCALVERSION_AUTO                        note<'triggers packaging failures'>
+
+CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE            note<'LP:1709171 LP:1848492'>
+
+CONFIG_MFD_SM501                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_SM501                                note<'boot essential on OMAP4'>
+
+CONFIG_MFD_TPS65217                             policy<{'arm64': 'm', 'armhf': 'y', 'ppc64el': 'n'}>
+CONFIG_MFD_TPS65217                             note<'boot essential on AM335x'>
+
+CONFIG_MMC_BLOCK                                policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MMC_BLOCK                                note<'boot essential on armhf/arm64'>
+
+CONFIG_MMC_OMAP_HS                              policy<{'armhf': 'y'}>
+CONFIG_MMC_OMAP_HS                              note<'boot essential on arm'>
+
+CONFIG_MMC_SDHCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI                                note<'installation essential on omap/highbank'>
+
+CONFIG_MMC_SDHCI_PLTFM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_PLTFM                          note<'boot essential on highbank'>
+
+CONFIG_MODIFY_LDT_SYSCALL                       policy<{'amd64': 'y'}>
+CONFIG_MODIFY_LDT_SYSCALL                       note<'Q: check this with security'>
+
+CONFIG_MODVERSIONS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODVERSIONS                              note<'LP:1898716 -- required as we have a livepatch/drivers modules signing key'>
+
+CONFIG_MTD                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MTD                                      note<'boot essential on arm'>
+
+CONFIG_MTD_BLOCK                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MTD_BLOCK                                note<'boot essential on arm'>
+
+CONFIG_MTD_DOCG3                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_DOCG3                                note<'LP:1792205'>
+
+CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE             note<'can be enabled at runtime'>
+
+CONFIG_MTD_NAND_OMAP2                           policy<{'armhf': 'y'}>
+CONFIG_MTD_NAND_OMAP2                           note<'boot essential on arm'>
+
+CONFIG_MTD_NAND_OMAP_BCH                        policy<{'armhf': 'y'}>
+CONFIG_MTD_NAND_OMAP_BCH                        note<'boot essential on arm'>
+
+CONFIG_MTD_OF_PARTS                             policy<{'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MTD_OF_PARTS                             note<'boot essential on arm'>
+
+CONFIG_MTD_ONENAND_VERIFY_WRITE                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_ONENAND_VERIFY_WRITE                 note<'writes here are not checked in full without'>
+
+CONFIG_MTD_RAW_NAND                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MTD_RAW_NAND                             note<'boot essential on arm'>
+
+CONFIG_NETWORK_PHY_TIMESTAMPING                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETWORK_PHY_TIMESTAMPING                 note<'LP:1785816'>
+
+CONFIG_NET_9P                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_9P                                   note<'LP:1557994'>
+
+CONFIG_NET_DROP_MONITOR                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_DROP_MONITOR                         note<'LP #1660634'>
+
+CONFIG_NET_SWITCHDEV                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_SWITCHDEV                            note<'LP: #1865452, updated to y for s390x starting with focal'>
+
+CONFIG_NET_VENDOR_EMULEX                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_EMULEX                        note<'LP:1543165'>
+
+CONFIG_NLS                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NLS                                      note<'dependancy of boot essential'>
+
+CONFIG_NOP_USB_XCEIV                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_NOP_USB_XCEIV                            note<'boot essential on omap/highbank'>
+
+CONFIG_NOUVEAU_LEGACY_CTX_SUPPORT               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NOUVEAU_LEGACY_CTX_SUPPORT               note<'Selects CONFIG_DRM_LEGACY which is not wanted'>
+
+CONFIG_NO_HZ_IDLE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NO_HZ_IDLE                               note<'LP:1413968'>
+
+CONFIG_NR_CPUS                                  policy<{'amd64': '8192', 'arm64': '256', 'armhf': '4', 'ppc64el': '2048', 's390x': '512'}>
+CONFIG_NR_CPUS                                  note<'LP:1864198'>
+
+CONFIG_NUMA                                     policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NUMA                                     note<'LP:1543165 LP:1557690'>
+
+CONFIG_NUMA_BALANCING_DEFAULT_ENABLED           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NUMA_BALANCING_DEFAULT_ENABLED           note<'LP:1557690'>
+
+CONFIG_NUMA_EMU                                 policy<{'amd64': 'y'}>
+CONFIG_NUMA_EMU                                 note<'LP:1864198'>
+
+CONFIG_NVMEM                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NVMEM                                    note<'Q: is this appropriate for s390x LP:1543165'>
+
+CONFIG_NVRAM                                    policy<{'amd64': 'm', 'ppc64el': 'y'}>
+CONFIG_NVRAM                                    note<'LP#1837726'>
+
+CONFIG_N_GSM                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_N_GSM                                    note<'LP#1404670'>
+
+CONFIG_OSNOISE_TRACER                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_OSNOISE_TRACER                           note<'This enables the osnoise tracer for the kernel. LP: #2018591'>
+
+CONFIG_PAGE_POISONING                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAGE_POISONING                           note<'LP:1783651'>
+
+CONFIG_PANIC_ON_OOPS                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PANIC_ON_OOPS                            note<'keep working if at all possible'>
+
+CONFIG_PATA_HPT3X3_DMA                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PATA_HPT3X3_DMA                          note<'DMA mode is documented problematic'>
+
+CONFIG_PCIEASPM_DEFAULT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIEASPM_DEFAULT                         note<'LP#1398544'>
+
+CONFIG_PCIEPORTBUS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_PCIEPORTBUS                              note<'LP#1665404'>
+
+CONFIG_PCIE_EDR                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_PCIE_EDR                                 note<'LP: #1965241'>
+
+CONFIG_PCI_MESON                                policy<{'amd64': 'n', 'arm64': 'm', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCI_MESON                                note<'LP: #2007745'>
+
+CONFIG_PCI_NR_FUNCTIONS                         policy<{'s390x': '512'}>
+CONFIG_PCI_NR_FUNCTIONS                         note<'LP:1866056'>
+
+CONFIG_PINCTRL_CHERRYVIEW                       policy<{'amd64': 'y'}>
+CONFIG_PINCTRL_CHERRYVIEW                       note<'LP #1630238'>
+
+CONFIG_PM                                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM                                       note<'LP:1867753'>
+
+CONFIG_PPC_MEM_KEYS                             policy<{'ppc64el': 'n'}>
+CONFIG_PPC_MEM_KEYS                             note<'LP:1776967'>
+
+CONFIG_PPC_SECURE_BOOT                          policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SECURE_BOOT                          note<'LP:1855668'>
+
+CONFIG_PPC_SECVAR_SYSFS                         policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SECVAR_SYSFS                         note<'LP:1866909'>
+
+CONFIG_PREEMPT_NONE                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_PREEMPT_NONE                             note<'LP:1543165'>
+
+CONFIG_PSI_DEFAULT_DISABLED                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_PSI_DEFAULT_DISABLED                     note<'LP:1876044'>
+
+CONFIG_QCOM_QDF2400_ERRATUM_0065                policy<{'arm64': 'y'}>
+CONFIG_QCOM_QDF2400_ERRATUM_0065                note<'LP:1672486'>
+
+CONFIG_QETH_OSX                                 policy<{'s390x': 'n'}>
+CONFIG_QETH_OSX                                 note<'LP#1959890'>
+
+CONFIG_RCU_CPU_STALL_TIMEOUT                    policy<{'amd64': '60', 'arm64': '60', 'armhf': '60', 'ppc64el': '60', 's390x': '60'}>
+CONFIG_RCU_CPU_STALL_TIMEOUT                    note<'LP:1991951'>
+
+CONFIG_REGULATOR_FIXED_VOLTAGE                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_FIXED_VOLTAGE                  note<'boot essential on arm'>
+
+CONFIG_REGULATOR_TPS65217                       policy<{'arm64': 'm', 'armhf': 'y'}>
+CONFIG_REGULATOR_TPS65217                       note<'boot essential on AM335x'>
+
+CONFIG_REGULATOR_TWL4030                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'y', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TWL4030                        note<'boot requisite for omap4'>
+
+CONFIG_RTC_DRV_CMOS                             policy<{'amd64': 'y', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_CMOS                             note<'boot essential on i386/amd64'>
+
+CONFIG_RTC_DRV_EFI                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RTC_DRV_EFI                              note<'LP:#1583738'>
+
+CONFIG_RTC_DRV_TWL4030                          policy<{'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_TWL4030                          note<'boot essential on OMAP3/OMAP4'>
+
+CONFIG_RT_GROUP_SCHED                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RT_GROUP_SCHED                           note<'LP#1875665'>
+
+CONFIG_S390_UV_UAPI                             policy<{'s390x': 'y'}>
+CONFIG_S390_UV_UAPI                             note<'LP:1959973'>
+
+CONFIG_SAMPLE_TRACE_PRINTK                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SAMPLE_TRACE_PRINTK                      note<'Required for ftrace selftests'>
+
+CONFIG_SATA_AHCI_PLATFORM                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SATA_AHCI_PLATFORM                       note<'boot essential on highbank'>
+
+CONFIG_SATA_HIGHBANK                            policy<{'armhf': 'y'}>
+CONFIG_SATA_HIGHBANK                            note<'LP:1703430'>
+
+CONFIG_SCLP_OFB                                 policy<{'s390x': 'y'}>
+CONFIG_SCLP_OFB                                 note<'LP:1787898'>
+
+CONFIG_SCSI_IPR_DUMP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_IPR_DUMP                            note<'LP:1343109'>
+
+CONFIG_SCSI_IPR_TRACE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_IPR_TRACE                           note<'LP:1343109'>
+
+CONFIG_SCSI_VIRTIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_VIRTIO                              note<'tech preview of new feature'>
+
+CONFIG_SECURITY_SAFESETID                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SAFESETID                       note<'LP:#1845391'>
+
+CONFIG_SECURITY_SELINUX_DISABLE                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECURITY_SELINUX_DISABLE                 note<'LP#1680315'>
+
+CONFIG_SERIAL_DEV_BUS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SERIAL_DEV_BUS                           note<'LP:1739939'>
+
+CONFIG_SERIAL_DEV_CTRL_TTYPORT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SERIAL_DEV_CTRL_TTYPORT                  note<'LP:1739939'>
+
+CONFIG_SERIAL_MULTI_INSTANTIATE                 policy<{'amd64': 'm'}>
+CONFIG_SERIAL_MULTI_INSTANTIATE                 note<'LP:#1965496'>
+
+CONFIG_SERIAL_SH_SCI                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_SH_SCI                            note<'LP: #2022361'>
+
+CONFIG_SERIAL_SH_SCI_CONSOLE                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_SH_SCI_CONSOLE                    note<'LP: #2022361'>
+
+CONFIG_SERIAL_SH_SCI_EARLYCON                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_SH_SCI_EARLYCON                   note<'LP: #2022361'>
+
+CONFIG_SETEND_EMULATION                         policy<{'arm64': 'y'}>
+CONFIG_SETEND_EMULATION                         note<'LP:1545542'>
+
+CONFIG_SMC                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SMC                                      note<'LP:1789934'>
+
+CONFIG_SMC_DIAG                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SMC_DIAG                                 note<'LP:1789934'>
+
+CONFIG_SND                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND                                      note<'not autoloadable on omap'>
+
+CONFIG_SND_HDA_POWER_SAVE_DEFAULT               policy<{'amd64': '1', 'arm64': '1', 'armhf': '1', 'ppc64el': '1'}>
+CONFIG_SND_HDA_POWER_SAVE_DEFAULT               note<'LP:1804265'>
+
+CONFIG_SND_HDA_RECONFIG                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_RECONFIG                         note<'allows fixes to be tested live'>
+
+CONFIG_SND_HDA_SCODEC_CS35L41                   policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_HDA_SCODEC_CS35L41                   note<'LP:#1965496'>
+
+CONFIG_SND_HDA_SCODEC_CS35L41_I2C               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_HDA_SCODEC_CS35L41_I2C               note<'LP:#1965496'>
+
+CONFIG_SND_HDA_SCODEC_CS35L41_SPI               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_HDA_SCODEC_CS35L41_SPI               note<'LP:#1965496'>
+
+CONFIG_SND_PCM_OSS                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_PCM_OSS                              note<'deprecated in favour of pulseaudio emulation'>
+
+CONFIG_SND_SOC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND_SOC                                  note<'not autoloadable on omap'>
+
+CONFIG_SND_SOC_AMD_ACP6x                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_AMD_ACP6x                        note<'LP:1949245'>
+
+CONFIG_SND_SOC_AMD_RENOIR                       policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_AMD_RENOIR                       note<'LP:1881046'>
+
+CONFIG_SND_SOC_AMD_RENOIR_MACH                  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_AMD_RENOIR_MACH                  note<'LP:1881046'>
+
+CONFIG_SND_SOC_AMD_YC_MACH                      policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_AMD_YC_MACH                      note<'LP:1949245'>
+
+CONFIG_SND_SOC_CS35L41                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L41                          note<'LP:#1965496'>
+
+CONFIG_SND_SOC_CS35L41_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L41_I2C                      note<'LP:#1965496'>
+
+CONFIG_SND_SOC_CS35L41_LIB                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L41_LIB                      note<'LP:#1965496'>
+
+CONFIG_SND_SOC_CS35L41_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L41_SPI                      note<'LP:#1965496'>
+
+CONFIG_SND_SOC_INTEL_CFL                        policy<{'amd64': 'n'}>
+CONFIG_SND_SOC_INTEL_CFL                        note<'deprecated'>
+
+CONFIG_SND_SOC_INTEL_CML_H                      policy<{'amd64': 'n'}>
+CONFIG_SND_SOC_INTEL_CML_H                      note<'deprecated'>
+
+CONFIG_SND_SOC_INTEL_CML_LP                     policy<{'amd64': 'n'}>
+CONFIG_SND_SOC_INTEL_CML_LP                     note<'deprecated'>
+
+CONFIG_SND_SOC_INTEL_CNL                        policy<{'amd64': 'n'}>
+CONFIG_SND_SOC_INTEL_CNL                        note<'deprecated'>
+
+CONFIG_SND_SOC_INTEL_SKYLAKE                    policy<{'amd64': 'n'}>
+CONFIG_SND_SOC_INTEL_SKYLAKE                    note<'deprecated'>
+
+CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC      policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC      note<'LP:1915117'>
+
+CONFIG_SND_SOC_INTEL_SOUNDWIRE_SOF_MACH         policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOUNDWIRE_SOF_MACH         note<'LP:1921632'>
+
+CONFIG_SND_SOC_INTEL_USER_FRIENDLY_LONG_NAMES   policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_INTEL_USER_FRIENDLY_LONG_NAMES   note<'LP:1921632'>
+
+CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC              policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC              note<'LP:1848490'>
+
+CONFIG_SND_SOC_SOF_HDA_LINK                     policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_SOF_HDA_LINK                     note<'LP:1848490'>
+
+CONFIG_SOUND                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SOUND                                    note<'not autoloadable on omap'>
+
+CONFIG_SOUNDWIRE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SOUNDWIRE                                note<'LP:1855685'>
+
+CONFIG_SOUND_OSS_CORE_PRECLAIM                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SOUND_OSS_CORE_PRECLAIM                  note<'LP#1105230 LP#1385510'>
+
+CONFIG_SPEAKUP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP                                  note<'LP: #1967702'>
+
+CONFIG_SPI_INTEL_SPI_PCI                        policy<{'amd64': 'n'}>
+CONFIG_SPI_INTEL_SPI_PCI                        note<'LP:1734147'>
+
+CONFIG_SPI_INTEL_SPI_PLATFORM                   policy<{'amd64': 'n'}>
+CONFIG_SPI_INTEL_SPI_PLATFORM                   note<'LP:1734147'>
+
+CONFIG_SQUASHFS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS                                 note<'LP#1593134'>
+
+CONFIG_SQUASHFS_4K_DEVBLK_SIZE                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SQUASHFS_4K_DEVBLK_SIZE                  note<'non-default block size'>
+
+CONFIG_STACK_VALIDATION                         policy<{'amd64': 'y'}>
+CONFIG_STACK_VALIDATION                         note<'needed for livepatch'>
+
+CONFIG_SWP_EMULATION                            policy<{'arm64': 'y'}>
+CONFIG_SWP_EMULATION                            note<'LP:1545542'>
+
+CONFIG_SYSFS_DEPRECATED                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SYSFS_DEPRECATED                         note<'ensure nothing is using these deprecated interfaces'>
+
+CONFIG_TCG_TIS_I2C_ATMEL                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_TCG_TIS_I2C_ATMEL                        note<'LP:1643652'>
+
+CONFIG_TCG_TIS_I2C_INFINEON                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_TCG_TIS_I2C_INFINEON                     note<'LP:1643652'>
+
+CONFIG_TCG_TIS_I2C_NUVOTON                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_TCG_TIS_I2C_NUVOTON                      note<'LP:1643652'>
+
+CONFIG_TCG_TPM                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TCG_TPM                                  note<'needed for early validation'>
+
+CONFIG_TEST_BLACKHOLE_DEV                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TEST_BLACKHOLE_DEV                       note<'Used by net selftests'>
+
+CONFIG_TIMERLAT_TRACER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TIMERLAT_TRACER                          note<'This enables the osnoise tracer for the kernel. LP: #2018591'>
+
+CONFIG_TMPFS_POSIX_ACL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TMPFS_POSIX_ACL                          note<'some /dev nodes require POSIX ACLs, like /dev/dsp'>
+
+CONFIG_TOUCHSCREEN_ELAN                         policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ELAN                         note<'LP #1630238'>
+
+CONFIG_UBSAN                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN                                    note<'LP#1942215'>
+
+CONFIG_UNWINDER_FRAME_POINTER                   policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_UNWINDER_FRAME_POINTER                   note<'needed for livepatch'>
+
+CONFIG_USB_EHCI_HCD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_EHCI_HCD                             note<'ensures USB 2.0/1.1 probe ordering'>
+
+CONFIG_USB_EHCI_HCD_PLATFORM                    policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'n', 'ppc64el': 'm'}>
+CONFIG_USB_EHCI_HCD_PLATFORM                    note<'Dont use the generic ehci/ohci code on omap, it doesnt work'>
+
+CONFIG_USB_HCD_BCMA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'n', 'ppc64el': 'm'}>
+CONFIG_USB_HCD_BCMA                             note<'USB_{O,E}HCI_HCD_PLATFORM must be off on omap'>
+
+CONFIG_USB_HCD_SSB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'n', 'ppc64el': 'm'}>
+CONFIG_USB_HCD_SSB                              note<'USB_{O,E}HCI_HCD_PLATFORM must be off on omap'>
+
+CONFIG_USB_M66592                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_M66592                               note<'gadget device'>
+
+CONFIG_USB_MUSB_HDRC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_USB_MUSB_HDRC                            note<'not autoloadable on omap'>
+
+CONFIG_USB_OHCI_HCD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_OHCI_HCD                             note<'ensures USB 2.0/1.1 probe ordering'>
+
+CONFIG_USB_OTG                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_OTG                                  note<'triggers breakage on x86 LP:1047527, LP:1411295'>
+
+CONFIG_USB_SERIAL_DEBUG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_DEBUG                         note<'not actually debug'>
+
+CONFIG_USB_UHCI_HCD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_UHCI_HCD                             note<'ensures USB 2.0/1.1 probe ordering'>
+
+CONFIG_USB_XHCI_DBGCAP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_XHCI_DBGCAP                          note<'LP:1730832'>
+
+CONFIG_USB_XHCI_HCD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_XHCI_HCD                             note<'ensures USB 2.0/1.1 probe ordering'>
+
+CONFIG_VFAT_FS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VFAT_FS                                  note<'needed on arm to ensure we can write the kernel when replacing'>
+
+CONFIG_VFIO                                     policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_VFIO                                     note<'LP#1636733'>
+
+CONFIG_VFIO_PCI                                 policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_VFIO_PCI                                 note<'LP#1636733'>
+
+CONFIG_VFIO_PCI_ZDEV_KVM                        policy<{'s390x': 'y'}>
+CONFIG_VFIO_PCI_ZDEV_KVM                        note<'LP#1853306 Enable VFIO zPCI pass-through for s390x'>
+
+CONFIG_VIDEO_VIMC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VIMC                               note<'LP#1831482'>
+
+CONFIG_VIRTIO_BLK                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTIO_BLK                               note<'KVM paravirt support -- not autoloadable'>
+
+CONFIG_VIRTIO_MMIO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_VIRTIO_MMIO                              note<'LP:1557689'>
+
+CONFIG_VIRTIO_NET                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTIO_NET                               note<'KVM paravirt support -- not autoloadable'>
+
+CONFIG_VMWARE_VMCI                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_VMWARE_VMCI                              note<'LP: #1978145'>
+
+CONFIG_VMWARE_VMCI_VSOCKETS                     policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_VMWARE_VMCI_VSOCKETS                     note<'LP: #1978145'>
+
+CONFIG_WWAN                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_WWAN                                     note<'LP: #2033406'>
+
+CONFIG_X509_CERTIFICATE_PARSER                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_X509_CERTIFICATE_PARSER                  note<'module signing'>
+
+CONFIG_X86_ACPI_CPUFREQ                         policy<{'amd64': 'y'}>
+CONFIG_X86_ACPI_CPUFREQ                         note<'not autoloadable'>
+
+CONFIG_X86_PCC_CPUFREQ                          policy<{'amd64': 'y'}>
+CONFIG_X86_PCC_CPUFREQ                          note<'not autoloadable'>
+
+CONFIG_X86_POWERNOW_K8                          policy<{'amd64': 'y'}>
+CONFIG_X86_POWERNOW_K8                          note<'not autoloadable'>
+
+CONFIG_X86_SPEEDSTEP_CENTRINO                   policy<{'amd64': 'y'}>
+CONFIG_X86_SPEEDSTEP_CENTRINO                   note<'not autoloadable'>
+
+CONFIG_X86_UV                                   policy<{'amd64': 'y'}>
+CONFIG_X86_UV                                   note<'LP:1863810'>
+
+CONFIG_XEN_512GB                                policy<{'amd64': 'y'}>
+CONFIG_XEN_512GB                                note<'Q: is this related to the utlemming questions on memory size?'>
+
+CONFIG_XEN_ACPI_PROCESSOR                       policy<{'amd64': 'y'}>
+CONFIG_XEN_ACPI_PROCESSOR                       note<'boot essential on XEN host'>
+
+CONFIG_XEN_BLKDEV_FRONTEND                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_BLKDEV_FRONTEND                      note<'not autoloadable -- XEN paravirt support'>
+
+CONFIG_XEN_NETDEV_FRONTEND                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_NETDEV_FRONTEND                      note<'not autoloadable -- XEN paravirt support'>
+
+CONFIG_XZ_DEC                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XZ_DEC                                   note<'boot essential -- initramfs decompressor'>
+
+CONFIG_ZCRYPT_MULTIDEVNODES                     policy<{'s390x': 'y'}>
+CONFIG_ZCRYPT_MULTIDEVNODES                     note<'LP:1805429'>
+
+CONFIG_ZLIB_DFLTCC                              policy<{'s390x': 'y'}>
+CONFIG_ZLIB_DFLTCC                              note<'LP:1830208'>
+
+CONFIG_ZONE_DMA                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 's390x': 'y'}>
+CONFIG_ZONE_DMA                                 note<'LP:1628523'>
+
+
+# ---- Annotations without notes ----
+
+CONFIG_104_QUAD_8                               policy<{'amd64': 'm'}>
+CONFIG_60XX_WDT                                 policy<{'amd64': 'm'}>
+CONFIG_64BIT                                    policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_6LOWPAN                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_6LOWPAN_DEBUGFS                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_GHC_EXT_HDR_DEST                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_GHC_EXT_HDR_FRAG                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_GHC_EXT_HDR_HOP                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_GHC_EXT_HDR_ROUTE                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_GHC_ICMPV6                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_GHC_UDP                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_6LOWPAN_NHC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_DEST                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_FRAGMENT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_HOP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_IPV6                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_MOBILITY                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_ROUTING                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6LOWPAN_NHC_UDP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_6PACK                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_8139CP                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_8139TOO                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_8139TOO_8129                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_8139TOO_PIO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_8139TOO_TUNE_TWISTER                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_8139_OLD_RX_RESET                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_842_COMPRESS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_842_DECOMPRESS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_88EU_AP_MODE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_9P_FS                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_9P_FSCACHE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_9P_FS_POSIX_ACL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_9P_FS_SECURITY                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_A11Y_BRAILLE_CONSOLE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_AAEON_IWMI_WDT                           policy<{'amd64': 'm'}>
+CONFIG_ABP060MG                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AC97_BUS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_ACENIC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ACENIC_OMIT_TIGON_I                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ACERHDF                                  policy<{'amd64': 'm'}>
+CONFIG_ACER_WIRELESS                            policy<{'amd64': 'm'}>
+CONFIG_ACER_WMI                                 policy<{'amd64': 'm'}>
+CONFIG_ACORN_PARTITION                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ACPI                                     policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_AC                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_ADXL                                policy<{'amd64': 'y'}>
+CONFIG_ACPI_ALS                                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_APEI                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_APEI_EINJ                           policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_APEI_ERST_DEBUG                     policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_ACPI_APEI_GHES                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_APEI_MEMORY_FAILURE                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_APEI_PCIEAER                        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_APEI_SEA                            policy<{'arm64': 'y'}>
+CONFIG_ACPI_BATTERY                             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_BGRT                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_BUTTON                              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_CCA_REQUIRED                        policy<{'arm64': 'y'}>
+CONFIG_ACPI_CMPC                                policy<{'amd64': 'm'}>
+CONFIG_ACPI_CONFIGFS                            policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_CONTAINER                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_CPPC_CPUFREQ                        policy<{'arm64': 'm'}>
+CONFIG_ACPI_CPPC_CPUFREQ_FIE                    policy<{'arm64': 'y'}>
+CONFIG_ACPI_CPPC_LIB                            policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_CPU_FREQ_PSS                        policy<{'amd64': 'y'}>
+CONFIG_ACPI_DEBUG                               policy<{'amd64': 'y', 'arm64': 'n'}>
+CONFIG_ACPI_DEBUGGER                            policy<{'amd64': 'y', 'arm64': 'n'}>
+CONFIG_ACPI_DEBUGGER_USER                       policy<{'amd64': 'y'}>
+CONFIG_ACPI_DOCK                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_DPTF                                policy<{'amd64': 'y'}>
+CONFIG_ACPI_EC_DEBUGFS                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_EXTLOG                              policy<{'amd64': 'm'}>
+CONFIG_ACPI_FAN                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_FPDT                                policy<{'amd64': 'y'}>
+CONFIG_ACPI_GENERIC_GSI                         policy<{'arm64': 'y'}>
+CONFIG_ACPI_GTDT                                policy<{'arm64': 'y'}>
+CONFIG_ACPI_HED                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_HMAT                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_HOTPLUG_CPU                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_HOTPLUG_IOAPIC                      policy<{'amd64': 'y'}>
+CONFIG_ACPI_HOTPLUG_MEMORY                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_I2C_OPREGION                        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_IORT                                policy<{'arm64': 'y'}>
+CONFIG_ACPI_IPMI                                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_LEGACY_TABLES_LOOKUP                policy<{'amd64': 'y'}>
+CONFIG_ACPI_LPIT                                policy<{'amd64': 'y'}>
+CONFIG_ACPI_MCFG                                policy<{'arm64': 'y'}>
+CONFIG_ACPI_MDIO                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_NFIT                                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_NUMA                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_PCI_SLOT                            policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_PLATFORM_PROFILE                    policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_PPTT                                policy<{'arm64': 'y'}>
+CONFIG_ACPI_PRMT                                policy<{'amd64': 'y'}>
+CONFIG_ACPI_PROCESSOR                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_PROCESSOR_AGGREGATOR                policy<{'amd64': 'm'}>
+CONFIG_ACPI_PROCESSOR_CSTATE                    policy<{'amd64': 'y'}>
+CONFIG_ACPI_PROCESSOR_IDLE                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_REDUCED_HARDWARE_ONLY               policy<{'amd64': 'n', 'arm64': 'y'}>
+CONFIG_ACPI_REV_OVERRIDE_POSSIBLE               policy<{'amd64': 'y'}>
+CONFIG_ACPI_SBS                                 policy<{'amd64': 'm'}>
+CONFIG_ACPI_SLEEP                               policy<{'amd64': 'y'}>
+CONFIG_ACPI_SPCR_TABLE                          policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT         policy<{'amd64': 'y'}>
+CONFIG_ACPI_TABLE_UPGRADE                       policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_TAD                                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ACPI_THERMAL                             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_THERMAL_REL                         policy<{'amd64': 'm'}>
+CONFIG_ACPI_TOSHIBA                             policy<{'amd64': 'm'}>
+CONFIG_ACPI_VIDEO                               policy<{'amd64': 'm'}>
+CONFIG_ACPI_VIOT                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_WATCHDOG                            policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ACPI_WMI                                 policy<{'amd64': 'm'}>
+CONFIG_ACQUIRE_WDT                              policy<{'amd64': 'm'}>
+CONFIG_ACRN_GUEST                               policy<{'amd64': 'y'}>
+CONFIG_ACRN_HSM                                 policy<{'amd64': 'm'}>
+CONFIG_AD2S1200                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD2S1210                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD2S90                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5064                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5110                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD525X_DPOT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_AD525X_DPOT_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD525X_DPOT_SPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5272                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5360                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5380                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5421                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5446                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5449                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5504                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5592R                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5592R_BASE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5593R                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5624R_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5686                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5686_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5696_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5755                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5758                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5761                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5764                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5766                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5770R                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5791                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD5933                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7091R5                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7124                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7150                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7192                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7266                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7280                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7291                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7292                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7298                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7303                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7476                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7606                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7606_IFACE_PARALLEL                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7606_IFACE_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7746                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7766                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7768_1                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7780                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7791                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7793                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7816                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7887                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7923                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD7949                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD799X                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD8366                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD8801                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD9467                                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD9523                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD9832                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD9834                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADAPTEC_STARFIRE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADE7854                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADE7854_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADE7854_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADF4350                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADF4371                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ADFS_FS_RW                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ADIN_PHY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ADIS16080                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16130                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16136                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16201                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16203                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16209                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16240                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16260                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16400                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16460                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16475                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADIS16480                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADI_AXI_ADC                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADJD_S311                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADM8211                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADT7316                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADT7316_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADT7316_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADUX1020                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADVANTECH_WDT                            policy<{'amd64': 'm'}>
+CONFIG_ADVISE_SYSCALLS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ADV_SWBUTTON                             policy<{'amd64': 'm'}>
+CONFIG_ADXL372                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADXL372_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADXL372_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADXRS290                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ADXRS450                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AD_SIGMA_DELTA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AEABI                                    policy<{'armhf': 'y'}>
+CONFIG_AFE4403                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AFE4404                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AFFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_AFIUCV                                   policy<{'s390x': 'm'}>
+CONFIG_AFS_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_AFS_DEBUG_CURSOR                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_AFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_AFS_FSCACHE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AF_KCM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_AF_RXRPC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_AF_RXRPC_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_AF_RXRPC_INJECT_LOSS                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_AF_RXRPC_IPV6                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AF_UNIX_OOB                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AGP_AMD64                                policy<{'amd64': 'y'}>
+CONFIG_AGP_INTEL                                policy<{'amd64': 'y'}>
+CONFIG_AGP_SIS                                  policy<{'amd64': 'm'}>
+CONFIG_AGP_VIA                                  policy<{'amd64': 'y'}>
+CONFIG_AHCI_BRCM                                policy<{'arm64': 'm'}>
+CONFIG_AHCI_CEVA                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AHCI_DM816                               policy<{'armhf': 'm'}>
+CONFIG_AHCI_IMX                                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_AHCI_MTK                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_AHCI_MVEBU                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_AHCI_QORIQ                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AHCI_SUNXI                               policy<{'arm64': 'n'}>
+CONFIG_AHCI_TEGRA                               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_AHCI_XGENE                               policy<{'arm64': 'm'}>
+CONFIG_AIC79XX_CMDS_PER_DEVICE                  policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32'}>
+CONFIG_AIC79XX_DEBUG_ENABLE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_AIC79XX_DEBUG_MASK                       policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_AIC79XX_REG_PRETTY_PRINT                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_AIC79XX_RESET_DELAY_MS                   policy<{'amd64': '5000', 'arm64': '5000', 'armhf': '5000', 'ppc64el': '5000'}>
+CONFIG_AIC7XXX_CMDS_PER_DEVICE                  policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8'}>
+CONFIG_AIC7XXX_DEBUG_ENABLE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_AIC7XXX_DEBUG_MASK                       policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_AIC7XXX_REG_PRETTY_PRINT                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_AIC7XXX_RESET_DELAY_MS                   policy<{'amd64': '5000', 'arm64': '5000', 'armhf': '5000', 'ppc64el': '5000'}>
+CONFIG_AIC94XX_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_AIO                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AIRO                                     policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_AIRO_CS                                  policy<{'amd64': 'm'}>
+CONFIG_AIX_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_AK09911                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AK8974                                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AK8975                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AL3010                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AL3320A                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ALIENWARE_WMI                            policy<{'amd64': 'm'}>
+CONFIG_ALIGNMENT_TRAP                           policy<{'armhf': 'y'}>
+CONFIG_ALIM1535_WDT                             policy<{'amd64': 'm'}>
+CONFIG_ALIM7101_WDT                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ALLOW_DEV_COREDUMP                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ALPINE_MSI                               policy<{'armhf': 'y'}>
+CONFIG_ALTERA_FREEZE_BRIDGE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ALTERA_MBOX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ALTERA_MSGDMA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ALTERA_PR_IP_CORE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ALTERA_PR_IP_CORE_PLAT                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ALTERA_STAPL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ALTERA_TSE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ALTIVEC                                  policy<{'ppc64el': 'y'}>
+CONFIG_ALX                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AL_FIC                                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_AM2315                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AM335X_CONTROL_USB                       policy<{'armhf': 'm'}>
+CONFIG_AM335X_PHY_USB                           policy<{'armhf': 'm'}>
+CONFIG_AMBA_PL08X                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_AMD8111_ETH                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AMDTEE                                   policy<{'amd64': 'm'}>
+CONFIG_AMD_IOMMU                                policy<{'amd64': 'y'}>
+CONFIG_AMD_IOMMU_V2                             policy<{'amd64': 'm'}>
+CONFIG_AMD_MEM_ENCRYPT                          policy<{'amd64': 'y'}>
+CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT        policy<{'amd64': 'n'}>
+CONFIG_AMD_NB                                   policy<{'amd64': 'y'}>
+CONFIG_AMD_NUMA                                 policy<{'amd64': 'y'}>
+CONFIG_AMD_PHY                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_AMD_PMC                                  policy<{'amd64': 'm'}>
+CONFIG_AMD_PTDMA                                policy<{'amd64': 'm'}>
+CONFIG_AMD_SFH_HID                              policy<{'amd64': 'm'}>
+CONFIG_AMD_XGBE                                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_AMD_XGBE_DCB                             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_AMD_XGBE_HAVE_ECC                        policy<{'amd64': 'y'}>
+CONFIG_AMIGA_PARTITION                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_AMILO_RFKILL                             policy<{'amd64': 'm'}>
+CONFIG_AMLOGIC_THERMAL                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ANDROID                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_ANDROID_BINDERFS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ANDROID_BINDER_DEVICES                   policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""'}>
+CONFIG_ANDROID_BINDER_IPC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ANDROID_BINDER_IPC_SELFTEST              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_APDS9300                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_APDS9802ALS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_APDS9960                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_APM_EMULATION                            policy<{'armhf': 'n'}>
+CONFIG_APPLDATA_BASE                            policy<{'s390x': 'y'}>
+CONFIG_APPLDATA_MEM                             policy<{'s390x': 'm'}>
+CONFIG_APPLDATA_NET_SUM                         policy<{'s390x': 'm'}>
+CONFIG_APPLDATA_OS                              policy<{'s390x': 'm'}>
+CONFIG_APPLE_AIC                                policy<{'arm64': 'y'}>
+CONFIG_APPLE_DART                               policy<{'arm64': 'm'}>
+CONFIG_APPLE_GMUX                               policy<{'amd64': 'm'}>
+CONFIG_APPLE_MFI_FASTCHARGE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_APPLE_PROPERTIES                         policy<{'amd64': 'y'}>
+CONFIG_APPLICOM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_APQ_GCC_8084                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_APQ_MMCC_8084                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_AQTION                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_AQUANTIA_PHY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_AR5523                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCH_32BIT_OFF_T                         policy<{'armhf': 'y'}>
+CONFIG_ARCH_32BIT_USTAT_F_TINODE                policy<{'s390x': 'y'}>
+CONFIG_ARCH_ACTIONS                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_ALPINE                              policy<{'arm64': 'n', 'armhf': 'y'}>
+CONFIG_ARCH_APPLE                               policy<{'arm64': 'y'}>
+CONFIG_ARCH_ARTPEC                              policy<{'armhf': 'y'}>
+CONFIG_ARCH_ASPEED                              policy<{'armhf': 'y'}>
+CONFIG_ARCH_AT91                                policy<{'armhf': 'n'}>
+CONFIG_ARCH_AXXIA                               policy<{'armhf-generic-lpae': 'y'}>
+CONFIG_ARCH_BCM                                 policy<{'armhf': 'n'}>
+CONFIG_ARCH_BCM2835                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_BCM4908                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_BCM_IPROC                           policy<{'arm64': 'y'}>
+CONFIG_ARCH_BERLIN                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_BINFMT_ELF_STATE                    policy<{'arm64': 'y', 's390x': 'y'}>
+CONFIG_ARCH_BITMAIN                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_BRCMSTB                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_CLOCKSOURCE_INIT                    policy<{'amd64': 'y'}>
+CONFIG_ARCH_CONFIGURES_CPU_MITIGATIONS          policy<{'amd64': 'y'}>
+CONFIG_ARCH_CPUIDLE_HALTPOLL                    policy<{'amd64': 'y'}>
+CONFIG_ARCH_CPU_PROBE_RELEASE                   policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_DIGICOLOR                           policy<{'armhf': 'n'}>
+CONFIG_ARCH_DMA_ADDR_T_64BIT                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_DOVE                                policy<{'armhf': 'n'}>
+CONFIG_ARCH_EMEV2                               policy<{'armhf': 'y'}>
+CONFIG_ARCH_ENABLE_HUGEPAGE_MIGRATION           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE             policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_ENABLE_SPLIT_PMD_PTLOCK             policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_ENABLE_THP_MIGRATION                policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_EP93XX                              policy<{'armhf': 'n'}>
+CONFIG_ARCH_EXYNOS                              policy<{'arm64': 'n', 'armhf': 'y'}>
+CONFIG_ARCH_EXYNOS3                             policy<{'armhf': 'n'}>
+CONFIG_ARCH_EXYNOS4                             policy<{'armhf': 'n'}>
+CONFIG_ARCH_EXYNOS5                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_FLATMEM_ENABLE                      policy<{'armhf': 'y'}>
+CONFIG_ARCH_FOOTBRIDGE                          policy<{'armhf': 'n'}>
+CONFIG_ARCH_HAS_ACPI_TABLE_UPGRADE              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_HAS_ADD_PAGES                       policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_BANDGAP                         policy<{'armhf': 'y'}>
+CONFIG_ARCH_HAS_BINFMT_FLAT                     policy<{'armhf': 'y'}>
+CONFIG_ARCH_HAS_CACHE_LINE_SIZE                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_HAS_CC_PLATFORM                     policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_COPY_MC                         policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_CPU_FINALIZE_INIT               policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_HAS_CPU_RELAX                       policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_DEBUG_VIRTUAL                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_DEBUG_VM_PGTABLE                policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_DEBUG_WX                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_DEVMEM_IS_ALLOWED               policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_DMA_MAP_DIRECT                  policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_DMA_PREP_COHERENT               policy<{'arm64': 'y'}>
+CONFIG_ARCH_HAS_EARLY_DEBUG                     policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_ELFCORE_COMPAT                  policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_ELF_RANDOMIZE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_FAST_MULTIPLIER                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_FILTER_PGPROT                   policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_FORCE_DMA_UNENCRYPTED           policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_FORTIFY_SOURCE                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_GIGANTIC_PAGE                   policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_HUGEPD                          policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_KCOV                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_KEEPINITRD                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_HAS_KEXEC_PURGATORY                 policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_MEMBARRIER_CALLBACKS            policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_MEMREMAP_COMPAT_ALIGN           policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_MEM_ENCRYPT                     policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_MMIOWB                          policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_PARANOID_L1D_FLUSH              policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_PHYS_TO_DMA                     policy<{'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_PKEYS                           policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_PMEM_API                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_PTE_DEVMAP                      policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_PTE_SPECIAL                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_RELR                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_HAS_RESET_CONTROLLER                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_HAS_RESTRICTED_VIRTIO_MEMORY_ACCESS policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_SCALED_CPUTIME                  policy<{'s390x': 'y'}>
+CONFIG_ARCH_HAS_SETUP_DMA_OPS                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_HAS_SET_DIRECT_MAP                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_HAS_SET_MEMORY                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_STRICT_KERNEL_RWX               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_STRICT_MODULE_RWX               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_SYNC_CORE_BEFORE_USERMODE       policy<{'amd64': 'y'}>
+CONFIG_ARCH_HAS_SYNC_DMA_FOR_CPU                policy<{'arm64': 'y', 'armhf-generic-lpae': 'y'}>
+CONFIG_ARCH_HAS_SYNC_DMA_FOR_DEVICE             policy<{'arm64': 'y', 'armhf-generic-lpae': 'y'}>
+CONFIG_ARCH_HAS_SYSCALL_WRAPPER                 policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_HAS_TICK_BROADCAST                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_UACCESS_FLUSHCACHE              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HAS_UBSAN_SANITIZE_ALL              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HAS_VDSO_DATA                       policy<{'s390x': 'y'}>
+CONFIG_ARCH_HAS_ZONE_DMA_SET                    policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H                  policy<{'armhf': 'y'}>
+CONFIG_ARCH_HAVE_ELF_PROT                       policy<{'arm64': 'y'}>
+CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_HI3xxx                              policy<{'armhf': 'y'}>
+CONFIG_ARCH_HIBERNATION_HEADER                  policy<{'amd64': 'y'}>
+CONFIG_ARCH_HIBERNATION_POSSIBLE                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_HIGHBANK                            policy<{'armhf': 'y'}>
+CONFIG_ARCH_HIP01                               policy<{'armhf': 'n'}>
+CONFIG_ARCH_HIP04                               policy<{'armhf': 'y'}>
+CONFIG_ARCH_HISI                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_HIX5HD2                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_INLINE_READ_LOCK                    policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_LOCK_BH                 policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_LOCK_IRQ                policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_LOCK_IRQSAVE            policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_TRYLOCK                 policy<{'s390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_UNLOCK                  policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_UNLOCK_BH               policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_UNLOCK_IRQ              policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_READ_UNLOCK_IRQRESTORE       policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_LOCK                    policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_LOCK_BH                 policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_LOCK_IRQ                policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_LOCK_IRQSAVE            policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_TRYLOCK                 policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_TRYLOCK_BH              policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_UNLOCK                  policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_UNLOCK_BH               policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_UNLOCK_IRQ              policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_SPIN_UNLOCK_IRQRESTORE       policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_LOCK                   policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_LOCK_BH                policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_LOCK_IRQ               policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_LOCK_IRQSAVE           policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_TRYLOCK                policy<{'s390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_UNLOCK                 policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_UNLOCK_BH              policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_UNLOCK_IRQ             policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INLINE_WRITE_UNLOCK_IRQRESTORE      policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_ARCH_INTEL_SOCFPGA                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_IOP32X                              policy<{'armhf': 'n'}>
+CONFIG_ARCH_IPQ40XX                             policy<{'armhf': 'n'}>
+CONFIG_ARCH_IXP4XX                              policy<{'armhf': 'n'}>
+CONFIG_ARCH_K3                                  policy<{'arm64': 'y'}>
+CONFIG_ARCH_KEEMBAY                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_KEEP_MEMBLOCK                       policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_KEYSTONE                            policy<{'armhf': 'n'}>
+CONFIG_ARCH_LAYERSCAPE                          policy<{'arm64': 'y'}>
+CONFIG_ARCH_LG1K                                policy<{'arm64': 'y'}>
+CONFIG_ARCH_MAY_HAVE_PC_FDC                     policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_MDM9615                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_MEDIATEK                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_MEMORY_PROBE                        policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_MESON                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC                 policy<{'amd64': 'y'}>
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT               policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_MIGHT_HAVE_PC_SERIO                 policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_MILBEAUT                            policy<{'armhf': 'y'}>
+CONFIG_ARCH_MILBEAUT_M10V                       policy<{'armhf': 'y'}>
+CONFIG_ARCH_MMAP_RND_BITS                       policy<{'amd64': '28', 'arm64': '18', 'armhf': '8', 'ppc64el': '28'}>
+CONFIG_ARCH_MMAP_RND_BITS_MAX                   policy<{'amd64': '32', 'arm64-generic': '33', 'arm64-generic-64k': '29', 'arm64-lowlatency': '33', 'arm64-lowlatency-64k': '29', 'armhf': '16', 'ppc64el': '29'}>
+CONFIG_ARCH_MMAP_RND_BITS_MIN                   policy<{'amd64': '28', 'arm64-generic': '18', 'arm64-generic-64k': '14', 'arm64-lowlatency': '18', 'arm64-lowlatency-64k': '14', 'armhf': '8', 'ppc64el': '14'}>
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS                policy<{'amd64': '8', 'arm64': '11', 'ppc64el': '8'}>
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX            policy<{'amd64': '16', 'arm64': '16', 'ppc64el': '13'}>
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN            policy<{'amd64': '8', 'arm64-generic': '11', 'arm64-generic-64k': '7', 'arm64-lowlatency': '11', 'arm64-lowlatency-64k': '7', 'ppc64el': '7'}>
+CONFIG_ARCH_MMP                                 policy<{'armhf': 'n'}>
+CONFIG_ARCH_MSM8960                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_MSM8974                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_MSM8X60                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_MSTARV7                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_MULTIPLATFORM                       policy<{'armhf': 'y'}>
+CONFIG_ARCH_MULTI_V6                            policy<{'armhf': 'n'}>
+CONFIG_ARCH_MULTI_V6_V7                         policy<{'armhf': 'y'}>
+CONFIG_ARCH_MULTI_V7                            policy<{'armhf': 'y'}>
+CONFIG_ARCH_MVEBU                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_MXC                                 policy<{'arm64': 'y', 'armhf-generic': 'y', 'armhf-generic-lpae': 'n'}>
+CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED              policy<{'armhf': 'y'}>
+CONFIG_ARCH_NPCM                                policy<{'armhf': 'y'}>
+CONFIG_ARCH_NPCM7XX                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_NR_GPIO                             policy<{'amd64': '1024', 'armhf': '2048'}>
+CONFIG_ARCH_OMAP                                policy<{'armhf': 'y'}>
+CONFIG_ARCH_OMAP1                               policy<{'armhf': 'n'}>
+CONFIG_ARCH_OMAP2PLUS                           policy<{'armhf': 'y'}>
+CONFIG_ARCH_OMAP2PLUS_TYPICAL                   policy<{'armhf': 'y'}>
+CONFIG_ARCH_OMAP3                               policy<{'armhf-generic': 'y', 'armhf-generic-lpae': 'n'}>
+CONFIG_ARCH_OMAP4                               policy<{'armhf-generic': 'y', 'armhf-generic-lpae': 'n'}>
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX                 policy<{'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT         policy<{'armhf': 'y'}>
+CONFIG_ARCH_PROC_KCORE_TEXT                     policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_PXA                                 policy<{'armhf': 'n'}>
+CONFIG_ARCH_QCOM                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_R7S72100                            policy<{'armhf': 'y'}>
+CONFIG_ARCH_R7S9210                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A73A4                             policy<{'armhf': 'n'}>
+CONFIG_ARCH_R8A7740                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7742                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7743                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7744                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7745                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A77470                            policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A774A1                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A774B1                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A774C0                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A774E1                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A7778                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7779                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7790                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7791                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7792                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7793                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A7794                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_R8A77950                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77951                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77960                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77961                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77965                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77970                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77980                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77990                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A77995                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R8A779A0                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_R9A06G032                           policy<{'armhf': 'y'}>
+CONFIG_ARCH_R9A07G044                           policy<{'arm64': 'y'}>
+CONFIG_ARCH_RANDOM                              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_RCAR_GEN1                           policy<{'armhf': 'y'}>
+CONFIG_ARCH_RCAR_GEN2                           policy<{'armhf': 'y'}>
+CONFIG_ARCH_RCAR_GEN3                           policy<{'arm64': 'y'}>
+CONFIG_ARCH_RDA                                 policy<{'armhf': 'y'}>
+CONFIG_ARCH_REALTEK                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_REALVIEW                            policy<{'armhf': 'n'}>
+CONFIG_ARCH_RENESAS                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_RMOBILE                             policy<{'armhf': 'y'}>
+CONFIG_ARCH_RPC                                 policy<{'armhf': 'n'}>
+CONFIG_ARCH_RZN1                                policy<{'armhf': 'y'}>
+CONFIG_ARCH_S32                                 policy<{'arm64': 'y'}>
+CONFIG_ARCH_S3C24XX                             policy<{'armhf': 'n'}>
+CONFIG_ARCH_S5PV210                             policy<{'armhf': 'n'}>
+CONFIG_ARCH_SA1100                              policy<{'armhf': 'n'}>
+CONFIG_ARCH_SEATTLE                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_SELECT_MEMORY_MODEL                 policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_SH73A0                              policy<{'armhf': 'y'}>
+CONFIG_ARCH_SPARSEMEM_DEFAULT                   policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SPARSEMEM_ENABLE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SPARX5                              policy<{'arm64': 'y'}>
+CONFIG_ARCH_SPRD                                policy<{'arm64': 'y'}>
+CONFIG_ARCH_STACKWALK                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_STI                                 policy<{'armhf': 'n'}>
+CONFIG_ARCH_STM32                               policy<{'armhf': 'n'}>
+CONFIG_ARCH_SUNXI                               policy<{'arm64': 'y', 'armhf': 'n'}>
+CONFIG_ARCH_SUPPORTS_ACPI                       policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SUPPORTS_BIG_ENDIAN                 policy<{'armhf': 'y'}>
+CONFIG_ARCH_SUPPORTS_CFI_CLANG                  policy<{'arm64': 'y'}>
+CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SUPPORTS_HUGETLBFS                  policy<{'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SUPPORTS_INT128                     policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_SUPPORTS_LTO_CLANG                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_SUPPORTS_LTO_CLANG_THIN             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE             policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_SUPPORTS_NUMA_BALANCING             policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SUPPORTS_UPROBES                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_SUSPEND_NONZERO_CPU                 policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_SUSPEND_POSSIBLE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_SYNQUACER                           policy<{'arm64': 'y'}>
+CONFIG_ARCH_TEGRA                               policy<{'arm64': 'y', 'armhf-generic': 'y', 'armhf-generic-lpae': 'n'}>
+CONFIG_ARCH_TEGRA_114_SOC                       policy<{'armhf-generic': 'y'}>
+CONFIG_ARCH_TEGRA_124_SOC                       policy<{'armhf-generic': 'y'}>
+CONFIG_ARCH_TEGRA_132_SOC                       policy<{'arm64': 'y'}>
+CONFIG_ARCH_TEGRA_186_SOC                       policy<{'arm64': 'y'}>
+CONFIG_ARCH_TEGRA_194_SOC                       policy<{'arm64': 'y'}>
+CONFIG_ARCH_TEGRA_210_SOC                       policy<{'arm64': 'y'}>
+CONFIG_ARCH_TEGRA_234_SOC                       policy<{'arm64': 'y'}>
+CONFIG_ARCH_TEGRA_2x_SOC                        policy<{'armhf-generic': 'y'}>
+CONFIG_ARCH_TEGRA_3x_SOC                        policy<{'armhf-generic': 'y'}>
+CONFIG_ARCH_THUNDER                             policy<{'arm64': 'y'}>
+CONFIG_ARCH_THUNDER2                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_U8500                               policy<{'armhf': 'n'}>
+CONFIG_ARCH_UNIPHIER                            policy<{'arm64': 'n', 'armhf': 'y'}>
+CONFIG_ARCH_USES_HIGH_VMA_FLAGS                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_USES_PG_UNCACHED                    policy<{'amd64': 'y'}>
+CONFIG_ARCH_USE_BUILTIN_BSWAP                   policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_USE_GNU_PROPERTY                    policy<{'arm64': 'y'}>
+CONFIG_ARCH_USE_MEMREMAP_PROT                   policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_USE_MEMTEST                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_USE_QUEUED_RWLOCKS                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_USE_QUEUED_SPINLOCKS                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_USE_SYM_ANNOTATIONS                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ARCH_VEXPRESS                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA        policy<{'armhf': 'y'}>
+CONFIG_ARCH_VEXPRESS_DCSCB                      policy<{'armhf': 'y'}>
+CONFIG_ARCH_VEXPRESS_SPC                        policy<{'armhf': 'y'}>
+CONFIG_ARCH_VEXPRESS_TC2_PM                     policy<{'armhf': 'y'}>
+CONFIG_ARCH_VIRT                                policy<{'armhf': 'y'}>
+CONFIG_ARCH_VISCONTI                            policy<{'arm64': 'y'}>
+CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT           policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_ARCH_WANTS_NO_INSTR                      policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_ARCH_WANTS_THP_SWAP                      policy<{'amd64': 'y'}>
+CONFIG_ARCH_WANT_BATCHED_UNMAP_TLB_FLUSH        policy<{'amd64': 'y'}>
+CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION       policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_WANT_DEFAULT_BPF_JIT                policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_WANT_FRAME_POINTERS                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_WANT_GENERAL_HUGETLB                policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_ARCH_WANT_HUGE_PMD_SHARE                 policy<{'amd64': 'y', 'arm64-generic': 'y', 'arm64-lowlatency': 'y'}>
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION              policy<{'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_WANT_IRQS_OFF_ACTIVATE_MM           policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_WANT_LD_ORPHAN_WARN                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ARCH_WANT_OLD_COMPAT_IPC                 policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ARCH_WEAK_RELEASE_ACQUIRE                policy<{'ppc64el': 'y'}>
+CONFIG_ARCH_WM8850                              policy<{'armhf': 'n'}>
+CONFIG_ARCH_XGENE                               policy<{'arm64': 'y'}>
+CONFIG_ARCH_ZYNQ                                policy<{'armhf': 'n'}>
+CONFIG_ARCH_ZYNQMP                              policy<{'arm64': 'y'}>
+CONFIG_ARCNET                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ARCNET_1051                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_1201                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_CAP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_COM20020                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_COM20020_CS                       policy<{'amd64': 'm'}>
+CONFIG_ARCNET_COM20020_PCI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_COM90xx                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_COM90xxIO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_RAW                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCNET_RIM_I                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARCX_ANYBUS_CONTROLLER                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ARC_EMAC_CORE                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM                                      policy<{'armhf': 'y'}>
+CONFIG_ARM64                                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_16K_PAGES                          policy<{'arm64': 'n'}>
+CONFIG_ARM64_4K_PAGES                           policy<{'arm64-generic': 'y', 'arm64-generic-64k': 'n', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'n'}>
+CONFIG_ARM64_64K_PAGES                          policy<{'arm64-generic': 'n', 'arm64-generic-64k': 'y', 'arm64-lowlatency': 'n', 'arm64-lowlatency-64k': 'y'}>
+CONFIG_ARM64_ACPI_PARKING_PROTOCOL              policy<{'arm64': 'y'}>
+CONFIG_ARM64_AMU_EXTN                           policy<{'arm64': 'y'}>
+CONFIG_ARM64_AS_HAS_MTE                         policy<{'arm64': 'y'}>
+CONFIG_ARM64_BTI                                policy<{'arm64': 'y'}>
+CONFIG_ARM64_CNP                                policy<{'arm64': 'y'}>
+CONFIG_ARM64_CONT_PMD_SHIFT                     policy<{'arm64-generic': '4', 'arm64-generic-64k': '5', 'arm64-lowlatency': '4', 'arm64-lowlatency-64k': '5'}>
+CONFIG_ARM64_CONT_PTE_SHIFT                     policy<{'arm64-generic': '4', 'arm64-generic-64k': '5', 'arm64-lowlatency': '4', 'arm64-lowlatency-64k': '5'}>
+CONFIG_ARM64_CRYPTO                             policy<{'arm64': 'y'}>
+CONFIG_ARM64_DEBUG_PRIORITY_MASKING             policy<{'arm64': 'n'}>
+CONFIG_ARM64_E0PD                               policy<{'arm64': 'y'}>
+CONFIG_ARM64_EPAN                               policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1024718                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1165522                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1286807                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1319367                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1418040                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1463225                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1508412                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1530923                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1542419                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_1742098                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_2054223                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_2067961                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_2441007                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_2441009                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_2457168                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_3194386                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_819472                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_824069                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_826319                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_827319                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_832075                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_834220                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_ERRATUM_845719                     policy<{'arm64': 'y'}>
+CONFIG_ARM64_HW_AFDBM                           policy<{'arm64': 'y'}>
+CONFIG_ARM64_LD_HAS_FIX_ERRATUM_843419          policy<{'arm64': 'y'}>
+CONFIG_ARM64_LSE_ATOMICS                        policy<{'arm64': 'y'}>
+CONFIG_ARM64_MODULE_PLTS                        policy<{'arm64': 'y'}>
+CONFIG_ARM64_MTE                                policy<{'arm64': 'y'}>
+CONFIG_ARM64_PAGE_SHIFT                         policy<{'arm64-generic': '12', 'arm64-generic-64k': '16', 'arm64-lowlatency': '12', 'arm64-lowlatency-64k': '16'}>
+CONFIG_ARM64_PAN                                policy<{'arm64': 'y'}>
+CONFIG_ARM64_PA_BITS                            policy<{'arm64': '48'}>
+CONFIG_ARM64_PA_BITS_48                         policy<{'arm64': 'y'}>
+CONFIG_ARM64_PA_BITS_52                         policy<{'arm64-generic-64k': 'n', 'arm64-lowlatency-64k': 'n'}>
+CONFIG_ARM64_PMEM                               policy<{'arm64': 'y'}>
+CONFIG_ARM64_PSEUDO_NMI                         policy<{'arm64': 'y'}>
+CONFIG_ARM64_PTR_AUTH                           policy<{'arm64': 'y'}>
+CONFIG_ARM64_PTR_AUTH_KERNEL                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_RAS_EXTN                           policy<{'arm64': 'y'}>
+CONFIG_ARM64_RELOC_TEST                         policy<{'arm64': 'n'}>
+CONFIG_ARM64_SVE                                policy<{'arm64': 'y'}>
+CONFIG_ARM64_SW_TTBR0_PAN                       policy<{'arm64': 'y'}>
+CONFIG_ARM64_TAGGED_ADDR_ABI                    policy<{'arm64': 'y'}>
+CONFIG_ARM64_TLB_RANGE                          policy<{'arm64': 'y'}>
+CONFIG_ARM64_VA_BITS                            policy<{'arm64': '48'}>
+CONFIG_ARM64_VA_BITS_39                         policy<{'arm64-generic': 'n', 'arm64-lowlatency': 'n'}>
+CONFIG_ARM64_VA_BITS_42                         policy<{'arm64-generic-64k': 'n', 'arm64-lowlatency-64k': 'n'}>
+CONFIG_ARM64_VA_BITS_52                         policy<{'arm64-generic-64k': 'n', 'arm64-lowlatency-64k': 'n'}>
+CONFIG_ARM64_WORKAROUND_CLEAN_CACHE             policy<{'arm64': 'y'}>
+CONFIG_ARM64_WORKAROUND_REPEAT_TLBI             policy<{'arm64': 'y'}>
+CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT          policy<{'arm64': 'y'}>
+CONFIG_ARM64_WORKAROUND_TSB_FLUSH_FAILURE       policy<{'arm64': 'y'}>
+CONFIG_ARMADA375_USBCLUSTER_PHY                 policy<{'armhf': 'y'}>
+CONFIG_ARMADA_370_CLK                           policy<{'armhf': 'y'}>
+CONFIG_ARMADA_370_XP_IRQ                        policy<{'armhf': 'y'}>
+CONFIG_ARMADA_370_XP_TIMER                      policy<{'armhf': 'y'}>
+CONFIG_ARMADA_375_CLK                           policy<{'armhf': 'y'}>
+CONFIG_ARMADA_37XX_CLK                          policy<{'arm64': 'y'}>
+CONFIG_ARMADA_37XX_RWTM_MBOX                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARMADA_37XX_WATCHDOG                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARMADA_38X_CLK                           policy<{'armhf': 'y'}>
+CONFIG_ARMADA_39X_CLK                           policy<{'armhf': 'y'}>
+CONFIG_ARMADA_AP806_SYSCON                      policy<{'arm64': 'y'}>
+CONFIG_ARMADA_AP_CPU_CLK                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARMADA_AP_CP_HELPER                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARMADA_CP110_SYSCON                      policy<{'arm64': 'y'}>
+CONFIG_ARMADA_THERMAL                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARMADA_XP_CLK                            policy<{'armhf': 'y'}>
+CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM       policy<{'arm64': 'm'}>
+CONFIG_ARM_AMBA                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_APPENDED_DTB                         policy<{'armhf': 'y'}>
+CONFIG_ARM_ARCH_TIMER                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_ARCH_TIMER_EVTSTREAM                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND            policy<{'arm64': 'y'}>
+CONFIG_ARM_ARMADA_37XX_CPUFREQ                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_ARMADA_8K_CPUFREQ                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_ATAG_DTB_COMPAT                      policy<{'armhf-generic': 'y', 'armhf-generic-lpae': 'n'}>
+CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND       policy<{'armhf-generic': 'y'}>
+CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER policy<{'armhf-generic': 'n'}>
+CONFIG_ARM_BIG_LITTLE_CPUIDLE                   policy<{'armhf': 'y'}>
+CONFIG_ARM_BRCMSTB_AVS_CPUFREQ                  policy<{'arm64': 'm'}>
+CONFIG_ARM_CCI                                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CCI400_COMMON                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CCI400_PMU                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CCI400_PORT_CTRL                     policy<{'armhf': 'y'}>
+CONFIG_ARM_CCI5xx_PMU                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CCI_PMU                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CCN                                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CHARLCD                              policy<{'armhf': 'y'}>
+CONFIG_ARM_CMN                                  policy<{'arm64': 'm'}>
+CONFIG_ARM_CPUIDLE                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_CPU_SUSPEND                          policy<{'armhf': 'y'}>
+CONFIG_ARM_CPU_TOPOLOGY                         policy<{'armhf': 'y'}>
+CONFIG_ARM_CRYPTO                               policy<{'armhf': 'y'}>
+CONFIG_ARM_DMA_IOMMU_ALIGNMENT                  policy<{'armhf': '8'}>
+CONFIG_ARM_DMA_MEM_BUFFERABLE                   policy<{'armhf': 'y'}>
+CONFIG_ARM_DMA_USE_IOMMU                        policy<{'armhf': 'y'}>
+CONFIG_ARM_DMC620_PMU                           policy<{'arm64': 'm'}>
+CONFIG_ARM_DSU_PMU                              policy<{'arm64': 'm'}>
+CONFIG_ARM_ERRATA_430973                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_643719                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_720789                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_754322                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_754327                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_764369                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_773022                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_775420                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_798181                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_814220                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_818325_852422                 policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_821420                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_825619                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_852421                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_852423                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_857271                        policy<{'armhf': 'y'}>
+CONFIG_ARM_ERRATA_857272                        policy<{'armhf': 'y'}>
+CONFIG_ARM_EXYNOS_BUS_DEVFREQ                   policy<{'armhf': 'y'}>
+CONFIG_ARM_EXYNOS_CPUIDLE                       policy<{'armhf': 'y'}>
+CONFIG_ARM_FFA_SMCCC                            policy<{'arm64': 'y'}>
+CONFIG_ARM_FFA_TRANSPORT                        policy<{'arm64': 'm'}>
+CONFIG_ARM_GIC                                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_GIC_MAX_NR                           policy<{'arm64': '1', 'armhf': '1'}>
+CONFIG_ARM_GIC_PM                               policy<{'arm64': 'y'}>
+CONFIG_ARM_GIC_V2M                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_GIC_V3                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_GIC_V3_ITS                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_GIC_V3_ITS_FSL_MC                    policy<{'arm64': 'y'}>
+CONFIG_ARM_GIC_V3_ITS_PCI                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_GLOBAL_TIMER                         policy<{'armhf': 'y'}>
+CONFIG_ARM_GT_INITIAL_PRESCALER_VAL             policy<{'armhf': '1'}>
+CONFIG_ARM_HAS_SG_CHAIN                         policy<{'armhf': 'y'}>
+CONFIG_ARM_HEAVY_MB                             policy<{'armhf': 'y'}>
+CONFIG_ARM_HIGHBANK_CPUFREQ                     policy<{'armhf': 'm'}>
+CONFIG_ARM_IMX6Q_CPUFREQ                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_ARM_IMX8M_DDRC_DEVFREQ                   policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_ARM_IMX_BUS_DEVFREQ                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_ARM_IMX_CPUFREQ_DT                       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_ARM_KPROBES_TEST                         policy<{'armhf': 'm'}>
+CONFIG_ARM_L1_CACHE_SHIFT                       policy<{'armhf': '7'}>
+CONFIG_ARM_L1_CACHE_SHIFT_6                     policy<{'armhf': 'y'}>
+CONFIG_ARM_L1_CACHE_SHIFT_7                     policy<{'armhf': 'y'}>
+CONFIG_ARM_LPAE                                 policy<{'armhf-generic': 'n', 'armhf-generic-lpae': 'y'}>
+CONFIG_ARM_MEDIATEK_CPUFREQ                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_MEDIATEK_CPUFREQ_HW                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_MHU                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_MHU_V2                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_MODULE_PLTS                          policy<{'armhf': 'y'}>
+CONFIG_ARM_MVEBU_V7_CPUIDLE                     policy<{'armhf': 'y'}>
+CONFIG_ARM_OMAP2PLUS_CPUFREQ                    policy<{'armhf': 'y'}>
+CONFIG_ARM_PATCH_IDIV                           policy<{'armhf': 'y'}>
+CONFIG_ARM_PATCH_PHYS_VIRT                      policy<{'armhf': 'y'}>
+CONFIG_ARM_PL172_MPMC                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_PMU                                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_PMU_ACPI                             policy<{'arm64': 'y'}>
+CONFIG_ARM_PSCI                                 policy<{'armhf': 'y'}>
+CONFIG_ARM_PSCI_CHECKER                         policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_ARM_PSCI_CPUIDLE                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_PSCI_CPUIDLE_DOMAIN                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_PSCI_FW                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_PTDUMP_CORE                          policy<{'armhf': 'y'}>
+CONFIG_ARM_PTDUMP_DEBUGFS                       policy<{'armhf': 'n'}>
+CONFIG_ARM_QCOM_CPUFREQ_HW                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_QCOM_CPUFREQ_NVMEM                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_QCOM_SPM_CPUIDLE                     policy<{'armhf': 'y'}>
+CONFIG_ARM_RASPBERRYPI_CPUFREQ                  policy<{'arm64': 'm'}>
+CONFIG_ARM_RK3399_DMC_DEVFREQ                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SBSA_WATCHDOG                        policy<{'arm64': 'm'}>
+CONFIG_ARM_SCMI_CPUFREQ                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SCMI_HAVE_MSG                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCMI_HAVE_SHMEM                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCMI_HAVE_TRANSPORT                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCMI_POWER_DOMAIN                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SCMI_PROTOCOL                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCMI_TRANSPORT_MAILBOX               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCMI_TRANSPORT_SMC                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCMI_TRANSPORT_VIRTIO                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SCPI_CPUFREQ                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SCPI_POWER_DOMAIN                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SCPI_PROTOCOL                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SDE_INTERFACE                        policy<{'arm64': 'y'}>
+CONFIG_ARM_SMCCC_SOC_ID                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_SMC_WATCHDOG                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SMMU                                 policy<{'arm64': 'y', 'armhf': 'n'}>
+CONFIG_ARM_SMMU_LEGACY_DT_BINDINGS              policy<{'arm64': 'n'}>
+CONFIG_ARM_SMMU_QCOM                            policy<{'arm64': 'y'}>
+CONFIG_ARM_SMMU_V3                              policy<{'arm64': 'y'}>
+CONFIG_ARM_SMMU_V3_PMU                          policy<{'arm64': 'm'}>
+CONFIG_ARM_SMMU_V3_SVA                          policy<{'arm64': 'y'}>
+CONFIG_ARM_SP805_WATCHDOG                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ARM_SPE_PMU                              policy<{'arm64': 'm'}>
+CONFIG_ARM_TEGRA124_CPUFREQ                     policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_ARM_TEGRA186_CPUFREQ                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_ARM_TEGRA194_CPUFREQ                     policy<{'arm64': 'm'}>
+CONFIG_ARM_TEGRA20_CPUFREQ                      policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_ARM_TEGRA_CPUIDLE                        policy<{'armhf-generic': 'n'}>
+CONFIG_ARM_TEGRA_DEVFREQ                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_ARM_THUMB                                policy<{'armhf': 'y'}>
+CONFIG_ARM_THUMBEE                              policy<{'armhf': 'y'}>
+CONFIG_ARM_TIMER_SP804                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ARM_TI_CPUFREQ                           policy<{'armhf': 'y'}>
+CONFIG_ARM_VEXPRESS_SPC_CPUFREQ                 policy<{'armhf': 'm'}>
+CONFIG_ARM_VIRT_EXT                             policy<{'armhf': 'y'}>
+CONFIG_AS3935                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AS73211                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ASHMEM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ASM_MODVERSIONS                          policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ASN1                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ASN1_ENCODER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ASPEED_ADC                               policy<{'armhf': 'm'}>
+CONFIG_ASPEED_BT_IPMI_BMC                       policy<{'armhf': 'm'}>
+CONFIG_ASPEED_KCS_IPMI_BMC                      policy<{'armhf': 'm'}>
+CONFIG_ASPEED_LPC_CTRL                          policy<{'armhf': 'm'}>
+CONFIG_ASPEED_LPC_SNOOP                         policy<{'armhf': 'm'}>
+CONFIG_ASPEED_P2A_CTRL                          policy<{'armhf': 'm'}>
+CONFIG_ASPEED_SOCINFO                           policy<{'armhf': 'y'}>
+CONFIG_ASPEED_WATCHDOG                          policy<{'armhf': 'y'}>
+CONFIG_ASSOCIATIVE_ARRAY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ASUS_LAPTOP                              policy<{'amd64': 'm'}>
+CONFIG_ASUS_NB_WMI                              policy<{'amd64': 'm'}>
+CONFIG_ASUS_WIRELESS                            policy<{'amd64': 'm'}>
+CONFIG_ASUS_WMI                                 policy<{'amd64': 'm'}>
+CONFIG_ASYMMETRIC_TPM_KEY_SUBTYPE               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ASYNC_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ASYNC_MEMCPY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ASYNC_PQ                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ASYNC_RAID6_RECOV                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ASYNC_RAID6_TEST                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ASYNC_TX_DISABLE_PQ_VAL_DMA              policy<{'arm64': 'y'}>
+CONFIG_ASYNC_TX_DISABLE_XOR_VAL_DMA             policy<{'arm64': 'y'}>
+CONFIG_ASYNC_TX_DMA                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ASYNC_TX_ENABLE_CHANNEL_SWITCH           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ASYNC_XOR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_AS_AVX512                                policy<{'amd64': 'y'}>
+CONFIG_AS_HAS_ARMV8_4                           policy<{'arm64': 'y'}>
+CONFIG_AS_HAS_ARMV8_5                           policy<{'arm64': 'y'}>
+CONFIG_AS_HAS_CFI_NEGATE_RA_STATE               policy<{'arm64': 'y'}>
+CONFIG_AS_HAS_LDAPR                             policy<{'arm64': 'y'}>
+CONFIG_AS_HAS_LSE_ATOMICS                       policy<{'arm64': 'y'}>
+CONFIG_AS_HAS_NON_CONST_LEB128                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AS_HAS_PAC                               policy<{'arm64': 'y'}>
+CONFIG_AS_IS_GNU                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AS_SHA1_NI                               policy<{'amd64': 'y'}>
+CONFIG_AS_SHA256_NI                             policy<{'amd64': 'y'}>
+CONFIG_AS_TPAUSE                                policy<{'amd64': 'y'}>
+CONFIG_AS_VERSION                               policy<{'amd64': '23800', 'arm64': '23800', 'armhf': '23800', 'ppc64el': '23800', 's390x': '23800'}>
+CONFIG_AS_VFP_VMRS_FPINST                       policy<{'armhf': 'y'}>
+CONFIG_AT76C50X_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AT803X_PHY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATA                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_ATAGS                                    policy<{'armhf': 'y'}>
+CONFIG_ATAGS_PROC                               policy<{'armhf': 'y'}>
+CONFIG_ATALK                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ATARI_PARTITION                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_ATA_ACPI                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ATA_BMDMA                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATA_FORCE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATA_GENERIC                              policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATA_OVER_ETH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ATA_SFF                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATA_VERBOSE_ERROR                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH10K                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH10K_AHB                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH10K_CE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH10K_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH10K_DEBUGFS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH10K_PCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH10K_SDIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH10K_SNOC                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ATH10K_SPECTRAL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH10K_TRACING                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH10K_USB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH11K                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH11K_AHB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH11K_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH11K_DEBUGFS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH11K_PCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH11K_SPECTRAL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH11K_TRACING                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH5K                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH5K_DEBUG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH5K_PCI                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH5K_TRACER                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH6KL                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH6KL_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH6KL_SDIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH6KL_TRACING                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH6KL_USB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH9K                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH9K_AHB                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_BTCOEX_SUPPORT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_CHANNEL_CONTEXT                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_COMMON                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH9K_COMMON_DEBUG                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_COMMON_SPECTRAL                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_DEBUGFS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_DYNACK                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATH9K_HTC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH9K_HTC_DEBUGFS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_HW                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH9K_HWRNG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_PCI                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_PCI_NO_EEPROM                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH9K_PCOEM                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_RFKILL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_STATION_STATISTICS                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH9K_WOW                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATH_COMMON                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATH_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATL1                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATL1C                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATL1E                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATL2                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATLAS_EZO_SENSOR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATLAS_PH_SENSOR                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ATMEL                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_AMBASSADOR                           policy<{'amd64': 'm'}>
+CONFIG_ATM_AMBASSADOR_DEBUG                     policy<{'amd64': 'n'}>
+CONFIG_ATM_BR2684                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_BR2684_IPFILTER                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_CLIP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_CLIP_NO_ICMP                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_DRIVERS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATM_DUMMY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_ENI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_ENI_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_ENI_TUNE_BURST                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_FIRESTREAM                           policy<{'amd64': 'm'}>
+CONFIG_ATM_FORE200E                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_FORE200E_DEBUG                       policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_ATM_FORE200E_TX_RETRY                    policy<{'amd64': '16', 'arm64': '16', 'armhf': '16', 'ppc64el': '16'}>
+CONFIG_ATM_FORE200E_USE_TASKLET                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_HE                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_HE_USE_SUNI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATM_HORIZON                              policy<{'amd64': 'm'}>
+CONFIG_ATM_HORIZON_DEBUG                        policy<{'amd64': 'n'}>
+CONFIG_ATM_IA                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_IA_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_IDT77252                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_IDT77252_DEBUG                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_IDT77252_RCV_ALL                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_IDT77252_USE_SUNI                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ATM_LANAI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_LANE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_MPOA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_NICSTAR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_NICSTAR_USE_IDT77105                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_NICSTAR_USE_SUNI                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ATM_SOLOS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_TCP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ATM_ZATM                                 policy<{'amd64': 'm'}>
+CONFIG_ATM_ZATM_DEBUG                           policy<{'amd64': 'n'}>
+CONFIG_ATOMIC64_SELFTEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ATP                                      policy<{'amd64': 'm'}>
+CONFIG_AUDIT                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AUDITSYSCALL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AUDIT_ARCH                               policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AUDIT_ARCH_COMPAT_GENERIC                policy<{'arm64': 'y'}>
+CONFIG_AUDIT_COMPAT_GENERIC                     policy<{'arm64': 'y'}>
+CONFIG_AUDIT_GENERIC                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_AUFS_FS                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_AUTOFS4_FS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'y'}>
+CONFIG_AUTOFS_FS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'y'}>
+CONFIG_AUTO_ZRELADDR                            policy<{'armhf': 'y'}>
+CONFIG_AUXDISPLAY                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_AUXILIARY_BUS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_AX25                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AX25_DAMA_SLAVE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_AX88796                                  policy<{'armhf': 'm'}>
+CONFIG_AX88796B_PHY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_AX88796_93CX6                            policy<{'armhf': 'n'}>
+CONFIG_AXI_DMAC                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_AXP20X_ADC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AXP20X_POWER                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AXP288_ADC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_AXP288_CHARGER                           policy<{'amd64': 'm'}>
+CONFIG_AXP288_FUEL_GAUGE                        policy<{'amd64': 'm'}>
+CONFIG_B43                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B43LEGACY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B43LEGACY_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43LEGACY_DMA                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_DMA_AND_PIO_MODE               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_DMA_MODE                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43LEGACY_HWRNG                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_LEDS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_PCICORE_AUTOSELECT             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_PCI_AUTOSELECT                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_PIO                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43LEGACY_PIO_MODE                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43_BCMA                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_BCMA_PIO                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_BUSES_BCMA                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43_BUSES_BCMA_AND_SSB                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_BUSES_SSB                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43_HWRNG                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_LEDS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PCICORE_AUTOSELECT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PCI_AUTOSELECT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PHY_G                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PHY_HT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PHY_LP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PHY_N                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_PIO                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B43_SDIO                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_B43_SSB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B44                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B44_PCI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B44_PCICORE_AUTOSELECT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B44_PCI_AUTOSELECT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_B53                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B53_MDIO_DRIVER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B53_MMAP_DRIVER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B53_SERDES                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B53_SPI_DRIVER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_B53_SRAB_DRIVER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_88PM860X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_AAT2870                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_ADP5520                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_ADP8860                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_ADP8870                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_APPLE                          policy<{'amd64': 'm'}>
+CONFIG_BACKLIGHT_ARCXCNN                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_AS3711                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_BD6107                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_CARILLO_RANCH                  policy<{'amd64': 'm'}>
+CONFIG_BACKLIGHT_CLASS_DEVICE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_BACKLIGHT_DA903X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_DA9052                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_GPIO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_KTD253                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LED                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LM3533                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LM3630A                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LM3639                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LP855X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LP8788                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_LV5207LP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_MAX8925                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_PANDORA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_PCF50633                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_PWM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_QCOM_WLED                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_RAVE_SP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_RT4831                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_SAHARA                         policy<{'amd64': 'm'}>
+CONFIG_BACKLIGHT_SKY81452                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKLIGHT_TPS65217                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_BACKLIGHT_WM831X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BACKTRACE_SELF_TEST                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BALLOON_COMPACTION                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BAREUDP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BASE_FULL                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BASE_SMALL                               policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_BATMAN_ADV                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BATMAN_ADV_BATMAN_V                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BATMAN_ADV_BLA                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BATMAN_ADV_DAT                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BATMAN_ADV_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BATMAN_ADV_MCAST                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BATMAN_ADV_NC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BATMAN_ADV_TRACING                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BATTERY_88PM860X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_ACER_A500                        policy<{'armhf-generic': 'm'}>
+CONFIG_BATTERY_ACT8945A                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_AXP20X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_BQ27XXX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_BQ27XXX_DT_UPDATES_NVM           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BATTERY_BQ27XXX_HDQ                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_BQ27XXX_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_CPCAP                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_CW2015                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DA9030                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DA9052                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DA9150                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DS2760                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DS2780                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DS2781                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_DS2782                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_GAUGE_LTC2941                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_GOLDFISH                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_MAX17040                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_MAX17042                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_MAX1721X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_RT5033                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_RX51                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_SBS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BATTERY_SURFACE                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_BATTERY_TWL4030_MADC                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BAYCOM_EPP                               policy<{'armhf': 'm'}>
+CONFIG_BAYCOM_PAR                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BAYCOM_SER_FDX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BAYCOM_SER_HDX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BCACHE                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BCACHE_ASYNC_REGISTRATION                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BCACHE_CLOSURES_DEBUG                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BCACHE_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BCH                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_BCM2711_THERMAL                          policy<{'arm64': 'm'}>
+CONFIG_BCM2835_MBOX                             policy<{'arm64': 'y'}>
+CONFIG_BCM2835_POWER                            policy<{'arm64': 'y'}>
+CONFIG_BCM2835_THERMAL                          policy<{'arm64': 'm'}>
+CONFIG_BCM2835_VCHIQ                            policy<{'arm64': 'm'}>
+CONFIG_BCM2835_VCHIQ_MMAL                       policy<{'arm64': 'm'}>
+CONFIG_BCM2835_WDT                              policy<{'arm64': 'm'}>
+CONFIG_BCM4908_ENET                             policy<{'arm64': 'm'}>
+CONFIG_BCM54140_PHY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BCM7038_L1_IRQ                           policy<{'arm64': 'y'}>
+CONFIG_BCM7038_WDT                              policy<{'arm64': 'm'}>
+CONFIG_BCM7XXX_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BCM84881_PHY                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_BCM87XX_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BCMA                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BCMA_BLOCKIO                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BCMA_DRIVER_GMAC_CMN                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_DRIVER_GPIO                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_DRIVER_PCI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_HOST_PCI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_HOST_PCI_POSSIBLE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_HOST_SOC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMA_POSSIBLE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BCMA_SFLASH                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BCMGENET                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BCM_FLEXRM_MBOX                          policy<{'arm64': 'm'}>
+CONFIG_BCM_IPROC_ADC                            policy<{'arm64': 'm'}>
+CONFIG_BCM_KONA_USB2_PHY                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BCM_NET_PHYLIB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BCM_NS_THERMAL                           policy<{'arm64': 'm'}>
+CONFIG_BCM_PDC_MBOX                             policy<{'arm64': 'm'}>
+CONFIG_BCM_PMB                                  policy<{'arm64': 'y'}>
+CONFIG_BCM_SBA_RAID                             policy<{'arm64': 'm'}>
+CONFIG_BCM_SR_THERMAL                           policy<{'arm64': 'm'}>
+CONFIG_BCM_VIDEOCORE                            policy<{'arm64': 'm'}>
+CONFIG_BCM_VK                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BCM_VK_TTY                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BD957XMUF_WATCHDOG                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BE2ISCSI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BE2NET                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BE2NET_BE2                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BE2NET_BE3                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BE2NET_HWMON                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BE2NET_LANCER                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BE2NET_SKYHAWK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BEFS_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BEFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BERLIN2_ADC                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_BFQ_CGROUP_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BFQ_GROUP_IOSCHED                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BGMAC                                    policy<{'arm64': 'y'}>
+CONFIG_BGMAC_PLATFORM                           policy<{'arm64': 'y'}>
+CONFIG_BH1750                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BH1780                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BIG_LITTLE                               policy<{'armhf': 'y'}>
+CONFIG_BINARY_PRINTF                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BINFMT_ELF                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BINFMT_ELF_FDPIC                         policy<{'armhf': 'y'}>
+CONFIG_BINFMT_FLAT                              policy<{'armhf': 'y'}>
+CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK          policy<{'armhf': 'y'}>
+CONFIG_BINFMT_FLAT_OLD                          policy<{'armhf': 'y'}>
+CONFIG_BINFMT_MISC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BINFMT_SHARED_FLAT                       policy<{'armhf': 'y'}>
+CONFIG_BINFMT_ZFLAT                             policy<{'armhf': 'y'}>
+CONFIG_BITREVERSE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_CGROUP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_CGROUP_FC_APPID                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_CGROUP_IOCOST                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_CGROUP_IOLATENCY                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BLK_CGROUP_IOPRIO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_CGROUP_RWSTAT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEBUG_FS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEBUG_FS_ZONED                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_3W_XXXX_RAID                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BLK_DEV_BSG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_BSGLIB                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_BSG_COMMON                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_CRYPTOLOOP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BLK_DEV_DM_BUILTIN                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_DRBD                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_FD                               policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_BLK_DEV_FD_RAWCMD                        policy<{'amd64': 'n', 'ppc64el': 'n'}>
+CONFIG_BLK_DEV_INITRD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_INTEGRITY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_INTEGRITY_T10                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_IO_TRACE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_LOOP                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_LOOP_MIN_COUNT                   policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8', 's390x': '8'}>
+CONFIG_BLK_DEV_MD                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_NBD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_NULL_BLK                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_PCIESSD_MTIP32XX                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BLK_DEV_PMEM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_BLK_DEV_RAM_COUNT                        policy<{'amd64': '16', 'arm64': '16', 'armhf': '16', 'ppc64el': '16', 's390x': '16'}>
+CONFIG_BLK_DEV_RBD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_RNBD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_DEV_RNBD_CLIENT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_RNBD_SERVER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BLK_DEV_RSXX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_BLK_DEV_THROTTLING_LOW                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BLK_DEV_ZONED                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_INLINE_ENCRYPTION                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_INLINE_ENCRYPTION_FALLBACK           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_MQ_PCI                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_MQ_RDMA                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_MQ_VIRTIO                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_PM                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BLK_RQ_ALLOC_TIME                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_SED_OPAL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_WBT                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLK_WBT_MQ                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLOCK                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLOCK_COMPAT                             policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLOCK_HOLDER_DEPRECATED                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BLOCK_LEGACY_AUTOLOAD                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BL_SWITCHER                              policy<{'armhf': 'y'}>
+CONFIG_BL_SWITCHER_DUMMY_IF                     policy<{'armhf': 'm'}>
+CONFIG_BMA220                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMA400                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMA400_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMA400_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMC150_ACCEL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMC150_ACCEL_I2C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMC150_ACCEL_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMC150_MAGN                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMC150_MAGN_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMC150_MAGN_SPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BME680                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BME680_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BME680_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMG160                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMG160_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMG160_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMI088_ACCEL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMI088_ACCEL_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMI160                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMI160_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMI160_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMP280                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMP280_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BMP280_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BNA                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BNX2                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BNX2X                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BNX2X_SRIOV                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BNXT                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BNXT_DCB                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BNXT_FLOWER_OFFLOAD                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BNXT_HWMON                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BNXT_SRIOV                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BOARD_TPCI200                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BONDING                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BOOTPARAM_HARDLOCKUP_PANIC               policy<{'amd64': 'n', 'ppc64el': 'n'}>
+CONFIG_BOOTPARAM_HARDLOCKUP_PANIC_VALUE         policy<{'amd64': '0', 'ppc64el': '0'}>
+CONFIG_BOOTPARAM_HOTPLUG_CPU0                   policy<{'amd64': 'n'}>
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE          policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE         policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_BOOTTIME_TRACING                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BOOTX_TEXT                               policy<{'ppc64el': 'n'}>
+CONFIG_BOOT_CONFIG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BOOT_PRINTK_DELAY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_BOUNCE                                   policy<{'armhf': 'y'}>
+CONFIG_BPF                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPFILTER                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPFILTER_UMH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BPF_EVENTS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_JIT                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_JIT_ALWAYS_ON                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_JIT_DEFAULT_ON                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_KPROBE_OVERRIDE                      policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_LSM                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_PRELOAD                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BPF_STREAM_PARSER                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPF_SYSCALL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BPQETHER                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BQL                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BRANCH_PROFILE_NONE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BRCMDBG                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BRCMFMAC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BRCMFMAC_PCIE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BRCMFMAC_PROTO_BCDC                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BRCMFMAC_PROTO_MSGBUF                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BRCMFMAC_SDIO                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BRCMFMAC_USB                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BRCMSMAC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BRCMSTB_DPFE                             policy<{'arm64': 'y'}>
+CONFIG_BRCMSTB_GISB_ARB                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_BRCMSTB_L2_IRQ                           policy<{'arm64': 'y'}>
+CONFIG_BRCMSTB_PM                               policy<{'arm64': 'y'}>
+CONFIG_BRCMSTB_THERMAL                          policy<{'arm64': 'm'}>
+CONFIG_BRCMUTIL                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BRCM_TRACING                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BRCM_USB_PINMAP                          policy<{'arm64': 'm'}>
+CONFIG_BRIDGE                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_CFM                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BRIDGE_EBT_802_3                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_AMONG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_ARP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_ARPREPLY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_BROUTE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_DNAT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_IP                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_IP6                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_LIMIT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_LOG                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_MARK                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_MARK_T                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_NFLOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_PKTTYPE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_REDIRECT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_SNAT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_STP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_T_FILTER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_T_NAT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_EBT_VLAN                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_IGMP_SNOOPING                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BRIDGE_MRP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BRIDGE_NETFILTER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_NF_EBTABLES                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BRIDGE_VLAN_FILTERING                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BROADCOM_PHY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BSD_DISKLABEL                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_BSD_PROCESS_ACCT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BSD_PROCESS_ACCT_V3                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BT                                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BTREE                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BTRFS_ASSERT                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BTRFS_DEBUG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BTRFS_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_BTRFS_FS_CHECK_INTEGRITY                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BTRFS_FS_POSIX_ACL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BTRFS_FS_REF_VERIFY                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BTRFS_FS_RUN_SANITY_TESTS                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BTT                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_6LOWPAN                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_AOSPEXT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_ATH3K                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_BCM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_BNEP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_BNEP_MC_FILTER                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_BNEP_PROTO_FILTER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_BREDR                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_CMTP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_DEBUGFS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIBCM203X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIBFUSB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIBLUECARD                           policy<{'amd64': 'm'}>
+CONFIG_BT_HCIBPA10X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIBT3C                               policy<{'amd64': 'm'}>
+CONFIG_BT_HCIBTSDIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIBTUSB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIBTUSB_AUTOSUSPEND                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIBTUSB_BCM                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIBTUSB_MTK                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIBTUSB_RTL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIDTL1                               policy<{'amd64': 'm'}>
+CONFIG_BT_HCIRSI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIUART                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIUART_3WIRE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_AG6XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_ATH3K                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_BCM                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_BCSP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_H4                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_INTEL                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_LL                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_MRVL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_NOKIA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HCIUART_QCA                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_RTL                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIUART_SERDEV                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_HCIVHCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_HIDP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_INTEL                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_LE                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_LEDS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_MRVL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_MRVL_SDIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_MSFTEXT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_MTKSDIO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_MTKUART                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_QCA                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_QCOMSMD                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_BT_RFCOMM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_RFCOMM_TTY                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_BT_RTL                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BT_SELFTEST                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_BT_VIRTIO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_BUG                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BUG_ON_DATA_CORRUPTION                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_BUILDTIME_TABLE_SORT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BUILD_BIN2C                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_BUILD_SALT                               policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_BXT_WC_PMIC_OPREGION                     policy<{'amd64': 'y'}>
+CONFIG_BYTCRC_PMIC_OPREGION                     policy<{'amd64': 'y'}>
+CONFIG_C2PORT                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_C2PORT_DURAMAR_2150                      policy<{'amd64': 'm'}>
+CONFIG_CACHEFILES                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CACHEFILES_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CACHE_FEROCEON_L2                        policy<{'armhf': 'y'}>
+CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH           policy<{'armhf': 'n'}>
+CONFIG_CACHE_L2X0                               policy<{'armhf': 'y'}>
+CONFIG_CACHE_L2X0_PMU                           policy<{'armhf': 'y'}>
+CONFIG_CACHE_TAUROS2                            policy<{'armhf': 'y'}>
+CONFIG_CACHE_UNIPHIER                           policy<{'armhf': 'y'}>
+CONFIG_CADENCE_WATCHDOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CAIF                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CAIF_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CAIF_DRIVERS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CAIF_NETDEV                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAIF_TTY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAIF_USB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAIF_VIRTIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CAN_8DEV_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_BCM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_CALC_BITTIMING                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CAN_CC770                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_CC770_ISA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_CC770_PLATFORM                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_C_CAN                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_C_CAN_PCI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_C_CAN_PLATFORM                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_DEBUG_DEVICES                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CAN_DEV                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_EMS_PCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_EMS_PCMCIA                           policy<{'amd64': 'm'}>
+CONFIG_CAN_EMS_USB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_ESD_USB2                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_ETAS_ES58X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_F81601                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_F81604                               policy<{'amd64': 'm', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CAN_FLEXCAN                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_GRCAN                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_GS_USB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_GW                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_HI311X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_IFI_CANFD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_ISOTP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_J1939                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_JANZ_ICAN3                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_KVASER_PCI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_KVASER_PCIEFD                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_KVASER_USB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_MCBA_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_MCP251X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_MCP251XFD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_MCP251XFD_SANITY                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CAN_MSCAN                                policy<{'ppc64el': 'm'}>
+CONFIG_CAN_M_CAN                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_M_CAN_PCI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_M_CAN_PLATFORM                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_M_CAN_TCAN4X5X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_PEAK_PCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_PEAK_PCIEC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CAN_PEAK_PCIEFD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_PEAK_PCMCIA                          policy<{'amd64': 'm'}>
+CONFIG_CAN_PEAK_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_PLX_PCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_RAW                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_RCAR                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CAN_RCAR_CANFD                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CAN_SJA1000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_SJA1000_ISA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_SJA1000_PLATFORM                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_SLCAN                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_SOFTING                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_SOFTING_CS                           policy<{'amd64': 'm'}>
+CONFIG_CAN_TI_HECC                              policy<{'armhf': 'm'}>
+CONFIG_CAN_UCAN                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_VCAN                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_VXCAN                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAN_XILINXCAN                            policy<{'arm64': 'm'}>
+CONFIG_CAPI_TRACE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CARDBUS                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_CARDMAN_4000                             policy<{'amd64': 'm'}>
+CONFIG_CARDMAN_4040                             policy<{'amd64': 'm'}>
+CONFIG_CARL9170                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CARL9170_DEBUGFS                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CARL9170_HWRNG                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CARL9170_LEDS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CARL9170_WPC                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CARMINE_DRAM_CUSTOM                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CASSINI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CAVIUM_CPT                               policy<{'arm64': 'm'}>
+CONFIG_CAVIUM_ERRATUM_22375                     policy<{'arm64': 'y'}>
+CONFIG_CAVIUM_ERRATUM_23144                     policy<{'arm64': 'y'}>
+CONFIG_CAVIUM_ERRATUM_23154                     policy<{'arm64': 'y'}>
+CONFIG_CAVIUM_ERRATUM_27456                     policy<{'arm64': 'y'}>
+CONFIG_CAVIUM_ERRATUM_30115                     policy<{'arm64': 'y'}>
+CONFIG_CAVIUM_PTP                               policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_CAVIUM_TX2_ERRATUM_219                   policy<{'arm64': 'y'}>
+CONFIG_CB710_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CB710_DEBUG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CB710_DEBUG_ASSUMPTIONS                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CC10001_ADC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CCS811                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CCW                                      policy<{'s390x': 'y'}>
+CONFIG_CCWGROUP                                 policy<{'s390x': 'm'}>
+CONFIG_CCW_CONSOLE                              policy<{'s390x': 'y'}>
+CONFIG_CC_CAN_LINK                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_CAN_LINK_STATIC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_ASM_GOTO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_ASM_GOTO_OUTPUT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_ASM_GOTO_TIED_OUTPUT              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_ASM_INLINE                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_BRANCH_PROT_PAC_RET               policy<{'arm64': 'y'}>
+CONFIG_CC_HAS_BRANCH_PROT_PAC_RET_BTI           policy<{'arm64': 'y'}>
+CONFIG_CC_HAS_INT128                            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_KASAN_GENERIC                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_KASAN_SW_TAGS                     policy<{'arm64': 'y'}>
+CONFIG_CC_HAS_NO_PROFILE_FN_ATTR                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_RETURN_THUNK                      policy<{'amd64': 'y'}>
+CONFIG_CC_HAS_SANCOV_TRACE_PC                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_SANE_STACKPROTECTOR               policy<{'amd64': 'y'}>
+CONFIG_CC_HAS_SIGN_RETURN_ADDRESS               policy<{'arm64': 'y'}>
+CONFIG_CC_HAS_SLS                               policy<{'amd64': 'y'}>
+CONFIG_CC_HAS_UBSAN_BOUNDS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_WORKING_NOSANITIZE_ADDRESS        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAS_ZERO_CALL_USED_REGS               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG            policy<{'arm64': 'y'}>
+CONFIG_CC_IS_GCC                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CC_OPTIMIZE_FOR_SIZE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CC_VERSION_TEXT                          policy<{'amd64': '"x86_64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0"', 'arm64': '"aarch64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0"', 'armhf': '"arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0"', 'ppc64el': '"powerpc64le-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0"', 's390x': '"s390x-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0"'}>
+CONFIG_CDNS_I3C_MASTER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CDROM                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CDROM_PKTCDVD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CDROM_PKTCDVD_BUFFERS                    policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8'}>
+CONFIG_CDROM_PKTCDVD_WCACHE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CEC_CH7322                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CEC_CORE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CEC_CROS_EC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CEC_GPIO                                 policy<{'amd64-lowlatency': 'm', 'arm64-lowlatency': 'm', 'arm64-lowlatency-64k': 'm'}>
+CONFIG_CEC_MESON_AO                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CEC_MESON_G12A_AO                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CEC_NOTIFIER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CEC_PIN                                  policy<{'amd64-lowlatency': 'y', 'arm64': 'y'}>
+CONFIG_CEC_PIN_ERROR_INJ                        policy<{'amd64-lowlatency': 'n', 'arm64': 'n'}>
+CONFIG_CEC_SAMSUNG_S5P                          policy<{'armhf': 'm'}>
+CONFIG_CEC_SECO                                 policy<{'amd64': 'm'}>
+CONFIG_CEC_SECO_RC                              policy<{'amd64': 'y'}>
+CONFIG_CEC_TEGRA                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CEPH_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CEPH_FSCACHE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CEPH_FS_POSIX_ACL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CEPH_FS_SECURITY_LABEL                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CEPH_LIB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CEPH_LIB_PRETTYDEBUG                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CEPH_LIB_USE_DNS_RESOLVER                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CFAG12864B                               policy<{'amd64': 'm'}>
+CONFIG_CFAG12864B_RATE                          policy<{'amd64': '20'}>
+CONFIG_CFG80211                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CFG80211_CERTIFICATION_ONUS              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CFG80211_CRDA_SUPPORT                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFG80211_DEBUGFS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFG80211_DEFAULT_PS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFG80211_DEVELOPER_WARNINGS              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CFG80211_REQUIRE_SIGNED_REGDB            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFG80211_USE_KERNEL_REGDB_KEYS           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFG80211_WEXT                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFG80211_WEXT_EXPORT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CFS_BANDWIDTH                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUPS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_BPF                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_CPUACCT                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CGROUP_DEVICE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_FREEZER                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_HUGETLB                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_MISC                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_NET_CLASSID                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_NET_PRIO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_PERF                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_PIDS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_RDMA                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_SCHED                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CGROUP_WRITEBACK                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CHARGER_88PM860X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_ADP5061                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_AXP20X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BD99954                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ2415X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ24190                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ24257                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ24735                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ2515X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ256XX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ25890                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_BQ25980                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_CPCAP                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CHARGER_CROS_PCHG                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CHARGER_CROS_USBPD                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CHARGER_DA9150                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_DETECTOR_MAX14656                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_GPIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_ISP1704                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_LP8727                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_LP8788                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_LT3651                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_LTC4162L                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MANAGER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHARGER_MAX14577                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MAX77650                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MAX77693                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MAX8903                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MAX8997                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MAX8998                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MP2629                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_MT6360                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_PCF50633                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_QCOM_SMBB                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CHARGER_RT9455                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_SBS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_SC2731                           policy<{'arm64': 'm'}>
+CONFIG_CHARGER_SMB347                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_SURFACE                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_CHARGER_TPS65090                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_TPS65217                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CHARGER_TWL4030                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_UCS1002                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARGER_WILCO                            policy<{'amd64': 'm'}>
+CONFIG_CHARLCD                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHARLCD_BL_FLASH                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHARLCD_BL_OFF                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CHARLCD_BL_ON                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CHECKPOINT_RESTORE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CHECK_SIGNATURE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHELSIO_INLINE_CRYPTO                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHELSIO_IPSEC_INLINE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHELSIO_LIB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHELSIO_T1                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHELSIO_T1_1G                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHELSIO_T3                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHELSIO_T4                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHELSIO_T4VF                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHELSIO_T4_DCB                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHELSIO_T4_FCOE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CHELSIO_TLS_DEVICE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CHROMEOS_LAPTOP                          policy<{'amd64': 'm'}>
+CONFIG_CHROMEOS_PSTORE                          policy<{'amd64': 'm'}>
+CONFIG_CHROMEOS_TBMC                            policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_CHROME_PLATFORMS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CHR_DEV_SCH                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CHR_DEV_ST                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CHSC_SCH                                 policy<{'s390x': 'm'}>
+CONFIG_CHTCRC_PMIC_OPREGION                     policy<{'amd64': 'y'}>
+CONFIG_CHT_DC_TI_PMIC_OPREGION                  policy<{'amd64': 'y'}>
+CONFIG_CHT_WC_PMIC_OPREGION                     policy<{'amd64': 'y'}>
+CONFIG_CICADA_PHY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CIFS                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CIFS_ALLOW_INSECURE_LEGACY               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_DEBUG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_DEBUG2                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CIFS_DEBUG_DUMP_KEYS                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CIFS_DFS_UPCALL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_FSCACHE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_POSIX                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_SMB_DIRECT                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CIFS_STATS2                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CIFS_SWN_UPCALL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_UPCALL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIFS_XATTR                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CIO2_BRIDGE                              policy<{'amd64': 'y'}>
+CONFIG_CIO_DAC                                  policy<{'amd64': 'm'}>
+CONFIG_CIO_INJECT                               policy<{'s390x': 'n'}>
+CONFIG_CLANG_VERSION                            policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_CLEANCACHE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CLKBLD_I8253                             policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_CLKEVT_I8253                             policy<{'amd64': 'y'}>
+CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK      policy<{'armhf': 'y'}>
+CONFIG_CLKSRC_EXYNOS_MCT                        policy<{'armhf': 'y'}>
+CONFIG_CLKSRC_IMX_GPT                           policy<{'armhf-generic': 'y'}>
+CONFIG_CLKSRC_IMX_TPM                           policy<{'armhf-generic': 'y'}>
+CONFIG_CLKSRC_MMIO                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CLKSRC_QCOM                              policy<{'armhf': 'y'}>
+CONFIG_CLKSRC_TI_32K                            policy<{'armhf': 'y'}>
+CONFIG_CLKSRC_VERSATILE                         policy<{'armhf': 'y'}>
+CONFIG_CLK_ACTIONS                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_BCM2711_DVP                          policy<{'arm64': 'm'}>
+CONFIG_CLK_BCM2835                              policy<{'arm64': 'y'}>
+CONFIG_CLK_BCM_NS2                              policy<{'arm64': 'y'}>
+CONFIG_CLK_BCM_SR                               policy<{'arm64': 'y'}>
+CONFIG_CLK_EMEV2                                policy<{'armhf': 'y'}>
+CONFIG_CLK_GFM_LPASS_SM8250                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CLK_IMX5                                 policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX6Q                                policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX6SL                               policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX6SLL                              policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX6SX                               policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX6UL                               policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX7D                                policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX7ULP                              policy<{'armhf-generic': 'y'}>
+CONFIG_CLK_IMX8MM                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CLK_IMX8MN                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CLK_IMX8MP                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CLK_IMX8MQ                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CLK_IMX8QXP                              policy<{'arm64': 'y'}>
+CONFIG_CLK_INTEL_SOCFPGA                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_INTEL_SOCFPGA32                      policy<{'armhf': 'y'}>
+CONFIG_CLK_INTEL_SOCFPGA64                      policy<{'arm64': 'y'}>
+CONFIG_CLK_LS1028A_PLLDIG                       policy<{'arm64': 'm'}>
+CONFIG_CLK_OWL_S500                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_OWL_S700                             policy<{'arm64': 'y'}>
+CONFIG_CLK_OWL_S900                             policy<{'arm64': 'y'}>
+CONFIG_CLK_PX30                                 policy<{'arm64': 'y'}>
+CONFIG_CLK_QORIQ                                policy<{'arm64': 'y'}>
+CONFIG_CLK_R7S9210                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7740                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7742                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7743                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7745                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A77470                             policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A774A1                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A774B1                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A774C0                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A774E1                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A7778                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7779                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7790                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7791                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7792                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7794                              policy<{'armhf': 'y'}>
+CONFIG_CLK_R8A7795                              policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77960                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77961                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77965                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77970                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77980                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77990                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A77995                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R8A779A0                             policy<{'arm64': 'y'}>
+CONFIG_CLK_R9A06G032                            policy<{'armhf': 'y'}>
+CONFIG_CLK_R9A07G044                            policy<{'arm64': 'y'}>
+CONFIG_CLK_RASPBERRYPI                          policy<{'arm64': 'm'}>
+CONFIG_CLK_RCAR_CPG_LIB                         policy<{'arm64': 'y'}>
+CONFIG_CLK_RCAR_GEN2_CPG                        policy<{'armhf': 'y'}>
+CONFIG_CLK_RCAR_GEN3_CPG                        policy<{'arm64': 'y'}>
+CONFIG_CLK_RCAR_USB2_CLOCK_SEL                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_RENESAS                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_RENESAS_CPG_MSSR                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_RENESAS_CPG_MSTP                     policy<{'armhf': 'y'}>
+CONFIG_CLK_RENESAS_DIV6                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_RK3036                               policy<{'armhf': 'y'}>
+CONFIG_CLK_RK312X                               policy<{'armhf': 'y'}>
+CONFIG_CLK_RK3188                               policy<{'armhf': 'y'}>
+CONFIG_CLK_RK322X                               policy<{'armhf': 'y'}>
+CONFIG_CLK_RK3288                               policy<{'armhf': 'y'}>
+CONFIG_CLK_RK3308                               policy<{'arm64': 'y'}>
+CONFIG_CLK_RK3328                               policy<{'arm64': 'y'}>
+CONFIG_CLK_RK3368                               policy<{'arm64': 'y'}>
+CONFIG_CLK_RK3399                               policy<{'arm64': 'y'}>
+CONFIG_CLK_RK3568                               policy<{'arm64': 'm'}>
+CONFIG_CLK_RV110X                               policy<{'armhf': 'y'}>
+CONFIG_CLK_RZA1                                 policy<{'armhf': 'y'}>
+CONFIG_CLK_RZG2L                                policy<{'arm64': 'y'}>
+CONFIG_CLK_SH73A0                               policy<{'armhf': 'y'}>
+CONFIG_CLK_SP810                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CLK_SUNXI                                policy<{'arm64': 'y'}>
+CONFIG_CLK_SUNXI_CLOCKS                         policy<{'arm64': 'y'}>
+CONFIG_CLK_SUNXI_PRCM_SUN6I                     policy<{'arm64': 'y'}>
+CONFIG_CLK_SUNXI_PRCM_SUN8I                     policy<{'arm64': 'y'}>
+CONFIG_CLK_SUNXI_PRCM_SUN9I                     policy<{'arm64': 'y'}>
+CONFIG_CLK_TEGRA_BPMP                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CLK_TWL6040                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CLK_UNIPHIER                             policy<{'armhf': 'y'}>
+CONFIG_CLK_VEXPRESS_OSC                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CLK_VF610                                policy<{'armhf-generic': 'y'}>
+CONFIG_CLOCKSOURCE_VALIDATE_LAST_CYCLE          policy<{'amd64': 'y'}>
+CONFIG_CLOCKSOURCE_WATCHDOG                     policy<{'amd64': 'y'}>
+CONFIG_CLONE_BACKWARDS                          policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CLONE_BACKWARDS2                         policy<{'s390x': 'y'}>
+CONFIG_CLS_U32_MARK                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CLS_U32_PERF                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CLZ_TAB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CM32181                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CM3232                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CM3323                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CM3605                                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CM36651                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CMA_ALIGNMENT                            policy<{'arm64': '8', 'armhf': '8'}>
+CONFIG_CMA_AREAS                                policy<{'arm64': '7', 'armhf': '7', 'ppc64el': '7', 's390x': '7'}>
+CONFIG_CMA_DEBUG                                policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CMA_DEBUGFS                              policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CMA_SIZE_SEL_MAX                         policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CMA_SIZE_SEL_MBYTES                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CMA_SIZE_SEL_MIN                         policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CMA_SIZE_SEL_PERCENTAGE                  policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CMA_SYSFS                                policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CMDLINE                                  policy<{'arm64': '"console=ttyAMA0"', 'armhf': '""', 'ppc64el': '""'}>
+CONFIG_CMDLINE_BOOL                             policy<{'amd64': 'n'}>
+CONFIG_CMDLINE_FORCE                            policy<{'arm64': 'n'}>
+CONFIG_CMDLINE_FROM_BOOTLOADER                  policy<{'arm64': 'y'}>
+CONFIG_CMDLINE_PARTITION                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_CMM                                      policy<{'ppc64el': 'm', 's390x': 'y'}>
+CONFIG_CMM_IUCV                                 policy<{'s390x': 'y'}>
+CONFIG_CMT_SPEECH                               policy<{'armhf-generic': 'm'}>
+CONFIG_CNIC                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CODA_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CODE_PATCHING_SELFTEST                   policy<{'ppc64el': 'n'}>
+CONFIG_COMEDI                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_COMEDI_8254                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_8255                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_8255_PCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_8255_SA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_1032                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_1500                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_1516                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_1564                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_16XX                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_2032                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_2200                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_3120                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_3501                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_APCI_3XXX                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADDI_WATCHDOG                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADL_PCI6208                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADL_PCI7X3X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADL_PCI8164                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADL_PCI9111                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADL_PCI9118                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADQ12B                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADV_PCI1710                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADV_PCI1720                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADV_PCI1723                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADV_PCI1724                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADV_PCI1760                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ADV_PCI_DIO                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AIO_AIO12_8                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AIO_IIRO_16                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_DIO200                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_DIO200_ISA                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_DIO200_PCI                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PC236                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PC236_ISA                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PC236_PCI                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PC263_ISA                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PC263_PCI                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PCI224                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_AMPLC_PCI230                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_BOND                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_C6XDIGIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_CB_DAS16_CS                       policy<{'amd64': 'm'}>
+CONFIG_COMEDI_CB_PCIDAS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_CB_PCIDAS64                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_CB_PCIDDA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_CB_PCIMDAS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_CB_PCIMDDA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_CONTEC_PCI_DIO                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAC02                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAQBOARD2000                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS08                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS08_CS                          policy<{'amd64': 'm'}>
+CONFIG_COMEDI_DAS08_ISA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS08_PCI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS16                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS16M1                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS1800                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS6402                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DAS800                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_COMEDI_DEFAULT_BUF_MAXSIZE_KB            policy<{'amd64': '20480', 'arm64': '20480', 'armhf': '20480', 'ppc64el': '20480'}>
+CONFIG_COMEDI_DEFAULT_BUF_SIZE_KB               policy<{'amd64': '2048', 'arm64': '2048', 'armhf': '2048', 'ppc64el': '2048'}>
+CONFIG_COMEDI_DMM32AT                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT2801                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT2811                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT2814                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT2815                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT2817                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT282X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT3000                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DT9812                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_DYNA_PCI10XX                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_FL512                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_GSC_HPDI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ICP_MULTI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_II_PCI20KC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ISADMA                            policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ISA_DRIVERS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_COMEDI_JR3_PCI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_KCOMEDILIB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_KE_COUNTER                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ME4000                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_ME_DAQ                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_MF6X4                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_MISC_DRIVERS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_COMEDI_MITE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_MPC624                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_MULTIQ3                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_6527                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_65XX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_660X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_670X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_ATMIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_ATMIO16D                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_AT_A2150                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_AT_AO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_DAQ_700_CS                     policy<{'amd64': 'm'}>
+CONFIG_COMEDI_NI_DAQ_DIO24_CS                   policy<{'amd64': 'm'}>
+CONFIG_COMEDI_NI_LABPC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_LABPC_CS                       policy<{'amd64': 'm'}>
+CONFIG_COMEDI_NI_LABPC_ISA                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_LABPC_ISADMA                   policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_LABPC_PCI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_MIO_CS                         policy<{'amd64': 'm'}>
+CONFIG_COMEDI_NI_PCIDIO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_PCIMIO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_ROUTING                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_TIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_TIOCMD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_NI_USB6501                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PARPORT                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCI_DRIVERS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL711                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL724                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL726                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL730                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL812                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL816                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCL818                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCM3724                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCMAD                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCMCIA_DRIVERS                    policy<{'amd64': 'm'}>
+CONFIG_COMEDI_PCMDA12                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCMMIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_PCMUIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_QUATECH_DAQP_CS                   policy<{'amd64': 'm'}>
+CONFIG_COMEDI_RTD520                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_RTI800                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_RTI802                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_S526                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_S626                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_TEST                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_TESTS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_TESTS_EXAMPLE                     policy<{'amd64': 'm', 'amd64-lowlatency': 'n', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_TESTS_NI_ROUTES                   policy<{'amd64': 'm', 'amd64-lowlatency': 'n', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_USBDUX                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_USBDUXFAST                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_USBDUXSIGMA                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_USB_DRIVERS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMEDI_VMK80XX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_COMMON_CLK_ASPEED                        policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_AXG                           policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_AXG_AUDIO                     policy<{'arm64': 'm', 'armhf': 'n'}>
+CONFIG_COMMON_CLK_AXI_CLKGEN                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_BD718XX                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_BM1880                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_CDCE706                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_CDCE925                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_CS2000_CP                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_FIXED_MMIO                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_COMMON_CLK_FSL_FLEXSPI                   policy<{'arm64': 'm'}>
+CONFIG_COMMON_CLK_FSL_SAI                       policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_G12A                          policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_GXBB                          policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_HI3516CV300                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_HI3519                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_HI3559A                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_HI3660                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_HI3670                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_HI3798CV200                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_HI6220                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_HI655X                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_IPROC                         policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_LOCHNAGAR                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_MAX77686                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_MAX9485                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_MEDIATEK                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MESON8B                       policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_MESON_AO_CLKC                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MESON_CPU_DYNDIV              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MESON_DUALDIV                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MESON_EE_CLKC                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MESON_MPLL                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MESON_PHASE                   policy<{'arm64': 'm'}>
+CONFIG_COMMON_CLK_MESON_PLL                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MESON_REGMAP                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MESON_SCLK_DIV                policy<{'arm64': 'm'}>
+CONFIG_COMMON_CLK_MESON_VID_PLL_DIV             policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2701                        policy<{'armhf': 'n'}>
+CONFIG_COMMON_CLK_MT2712                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_BDPSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_JPGDECSYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_MFGCFG                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_VDECSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT2712_VENCSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_AUDIOSYS               policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_CAMSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_GCESYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MFGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MIPI0ASYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MIPI0BSYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MIPI1ASYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MIPI1BSYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MIPI2ASYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MIPI2BSYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6765_VCODECSYS              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_AUDSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_CAMSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_IPESYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_MFGCFG                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_VDECSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6779_VENCSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6797                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6797_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6797_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6797_VDECSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT6797_VENCSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT7622                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT7622_AUDSYS                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT7622_ETHSYS                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT7622_HIFSYS                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT7629                        policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT7629_ETHSYS                 policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT7629_HIFSYS                 policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT8135                        policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT8167                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8167_AUDSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8167_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8167_MFGCFG                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8167_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8167_VDECSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8173                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT8173_MMSYS                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT8183                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_AUDIOSYS               policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_CAMSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_IPU_ADL                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_IPU_CONN               policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_IPU_CORE0              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_IPU_CORE1              policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_MFGCFG                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_VDECSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8183_VENCSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_AUDSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_CAMSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_IMGSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_IMP_IIC_WRAP           policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_IPESYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_MDPSYS                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_MFGCFG                 policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_MMSYS                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_MSDC                   policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_SCP_ADSP               policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_VDECSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8192_VENCSYS                policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_MT8516                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_MT8516_AUDSYS                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_PALMAS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_PWM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_QCOM                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_RK808                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_ROCKCHIP                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_COMMON_CLK_S2MPS11                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_SAMSUNG                       policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_SCMI                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_SCPI                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_CLK_SI514                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_SI5341                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_SI5351                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_SI544                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_SI570                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_TI_ADPLL                      policy<{'armhf': 'y'}>
+CONFIG_COMMON_CLK_VC5                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_WM831X                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_XGENE                         policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_XLNX_CLKWZRD                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_COMMON_CLK_ZYNQMP                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_RESET_HI3660                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMMON_RESET_HI6220                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_COMPACTION                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_COMPAL_LAPTOP                            policy<{'amd64': 'm'}>
+CONFIG_COMPAT                                   policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_COMPAT_32                                policy<{'amd64': 'y'}>
+CONFIG_COMPAT_32BIT_TIME                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_COMPAT_BINFMT_ELF                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_COMPAT_FOR_U64_ALIGNMENT                 policy<{'amd64': 'y'}>
+CONFIG_COMPAT_NETLINK_MESSAGES                  policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_COMPAT_OLD_SIGACTION                     policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_COMPAT_VDSO                              policy<{'amd64': 'n'}>
+CONFIG_COMPILE_TEST                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CONFIGFS_FS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CONNECTOR                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT                 policy<{'amd64': '7', 'arm64': '7', 'armhf': '7', 'ppc64el': '7', 's390x': '7'}>
+CONFIG_CONSOLE_LOGLEVEL_QUIET                   policy<{'amd64': '4', 'arm64': '4', 'armhf': '4', 'ppc64el': '4', 's390x': '4'}>
+CONFIG_CONSOLE_POLL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CONSOLE_TRANSLATIONS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CONTEXT_SWITCH_TRACER                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CONTIG_ALLOC                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CORDIC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_COREDUMP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CORESIGHT                                policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CORTINA_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_COUNTER                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CPA_DEBUG                                policy<{'amd64': 'n'}>
+CONFIG_CPCAP_ADC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CPU5_WDT                                 policy<{'amd64': 'm'}>
+CONFIG_CPUFREQ_DT_PLATDEV                       policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPUMASK_OFFSTACK                         policy<{'amd64': 'y'}>
+CONFIG_CPUSETS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CPU_32v6K                                policy<{'armhf': 'y'}>
+CONFIG_CPU_32v7                                 policy<{'armhf': 'y'}>
+CONFIG_CPU_ABRT_EV7                             policy<{'armhf': 'y'}>
+CONFIG_CPU_BIG_ENDIAN                           policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_CPU_BPREDICT_DISABLE                     policy<{'armhf': 'n'}>
+CONFIG_CPU_CACHE_V7                             policy<{'armhf': 'y'}>
+CONFIG_CPU_CACHE_VIPT                           policy<{'armhf': 'y'}>
+CONFIG_CPU_COPY_V6                              policy<{'armhf': 'y'}>
+CONFIG_CPU_CP15                                 policy<{'armhf': 'y'}>
+CONFIG_CPU_CP15_MMU                             policy<{'armhf': 'y'}>
+CONFIG_CPU_FREQ                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE        policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND            policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_SCHEDUTIL           policy<{'amd64': 'y', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CPU_FREQ_GOV_ATTR_SET                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_COMMON                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_GOV_SCHEDUTIL                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_FREQ_THERMAL                         policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_HAS_ASID                             policy<{'armhf': 'y'}>
+CONFIG_CPU_HOTPLUG_STATE_CONTROL                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CPU_IBPB_ENTRY                           policy<{'amd64': 'y'}>
+CONFIG_CPU_IBRS_ENTRY                           policy<{'amd64': 'y'}>
+CONFIG_CPU_ICACHE_DISABLE                       policy<{'armhf': 'n'}>
+CONFIG_CPU_ICACHE_MISMATCH_WORKAROUND           policy<{'armhf': 'y'}>
+CONFIG_CPU_IDLE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_IDLE_GOV_HALTPOLL                    policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_IDLE_GOV_LADDER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_IDLE_GOV_MENU                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_IDLE_GOV_TEO                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_IDLE_MULTIPLE_DRIVERS                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CPU_IDLE_THERMAL                         policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_ISOLATION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CPU_LITTLE_ENDIAN                        policy<{'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_MITIGATIONS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CPU_PABRT_V7                             policy<{'armhf': 'y'}>
+CONFIG_CPU_PJ4                                  policy<{'armhf': 'y'}>
+CONFIG_CPU_PJ4B                                 policy<{'armhf': 'y'}>
+CONFIG_CPU_PM                                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CPU_RMAP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CPU_SPECTRE                              policy<{'armhf': 'y'}>
+CONFIG_CPU_SRSO                                 policy<{'amd64': 'y'}>
+CONFIG_CPU_SUP_AMD                              policy<{'amd64': 'y'}>
+CONFIG_CPU_SUP_CENTAUR                          policy<{'amd64': 'y'}>
+CONFIG_CPU_SUP_HYGON                            policy<{'amd64': 'y'}>
+CONFIG_CPU_SUP_INTEL                            policy<{'amd64': 'y'}>
+CONFIG_CPU_SUP_ZHAOXIN                          policy<{'amd64': 'y'}>
+CONFIG_CPU_SW_DOMAIN_PAN                        policy<{'armhf-generic': 'y'}>
+CONFIG_CPU_THERMAL                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CPU_THUMB_CAPABLE                        policy<{'armhf': 'y'}>
+CONFIG_CPU_TLB_V7                               policy<{'armhf': 'y'}>
+CONFIG_CPU_UNRET_ENTRY                          policy<{'amd64': 'y'}>
+CONFIG_CPU_V7                                   policy<{'armhf': 'y'}>
+CONFIG_CRAMFS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CRAMFS_BLOCKDEV                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CRAMFS_MTD                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_CRASH_CORE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRC16                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRC32                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRC32_BIT                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRC32_SARWATE                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRC32_SELFTEST                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRC32_SLICEBY4                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRC32_SLICEBY8                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRC4                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRC64                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRC7                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRC8                                     policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRC_CCITT                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRC_ITU_T                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRC_T10DIF                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CROSS_MEMORY_ATTACH                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CROS_EC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_CHARDEV                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_DEBUGFS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_ISHTP                            policy<{'amd64': 'm'}>
+CONFIG_CROS_EC_LIGHTBAR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_LPC                              policy<{'amd64': 'm'}>
+CONFIG_CROS_EC_MKBP_PROXIMITY                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_PROTO                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CROS_EC_RPMSG                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_SENSORHUB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_SYSFS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_TYPEC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_EC_VBC                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_KBD_LED_BACKLIGHT                   policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_CROS_USBPD_LOGGER                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CROS_USBPD_NOTIFY                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_842                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ACOMP2                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_ADIANTUM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_AEAD                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_AEAD2                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_AEGIS128                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_AEGIS128_AESNI_SSE2               policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_AEGIS128_SIMD                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CRYPTO_AES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_AES_ARM                           policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_AES_ARM64                         policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_AES_ARM64_BS                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_AES_ARM64_CE                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_AES_ARM64_CE_BLK                  policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_AES_ARM64_CE_CCM                  policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_AES_ARM64_NEON_BLK                policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_AES_ARM_BS                        policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_AES_ARM_CE                        policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_AES_NI_INTEL                      policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_AES_S390                          policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_AES_TI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_AKCIPHER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_AKCIPHER2                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_ALGAPI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_ALGAPI2                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_ANSI_CPRNG                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ARCH_HAVE_LIB_BLAKE2S             policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_CRYPTO_ARCH_HAVE_LIB_CHACHA              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_ARCH_HAVE_LIB_CURVE25519          policy<{'amd64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_ARCH_HAVE_LIB_POLY1305            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_AUTHENC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_BLAKE2B                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_BLAKE2B_NEON                      policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_BLAKE2S_ARM                       policy<{'armhf': 'y'}>
+CONFIG_CRYPTO_BLAKE2S_X86                       policy<{'amd64': 'y'}>
+CONFIG_CRYPTO_BLOWFISH                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_BLOWFISH_COMMON                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_BLOWFISH_X86_64                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CAMELLIA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CAMELLIA_AESNI_AVX2_X86_64        policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CAMELLIA_AESNI_AVX_X86_64         policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CAMELLIA_X86_64                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CAST5                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CAST5_AVX_X86_64                  policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CAST6                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CAST6_AVX_X86_64                  policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CAST_COMMON                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CBC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_CCM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CFB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CHACHA20                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CHACHA20POLY1305                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CHACHA20_NEON                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_CHACHA20_X86_64                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CHACHA_S390                       policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_CMAC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CRC32                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CRC32C                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_CRC32C_INTEL                      policy<{'amd64': 'y'}>
+CONFIG_CRYPTO_CRC32C_VPMSUM                     policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_CRC32_ARM_CE                      policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_CRC32_PCLMUL                      policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CRC32_S390                        policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_CRCT10DIF                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_CRCT10DIF_ARM64_CE                policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_CRCT10DIF_ARM_CE                  policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_CRCT10DIF_PCLMUL                  policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_CRCT10DIF_VPMSUM                  policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_CRYPTD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CTR                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_CTS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_CURVE25519                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_CURVE25519_NEON                   policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_CURVE25519_X86                    policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEFLATE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_CRYPTO_DES                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_DES3_EDE_X86_64                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DES_S390                          policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_DEV_ALLWINNER                     policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_AMLOGIC_GXL                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_DEV_AMLOGIC_GXL_DEBUG             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRYPTO_DEV_ARTPEC6                       policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_ATMEL_ECC                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CRYPTO_DEV_ATMEL_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_ATMEL_SHA204A                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CRYPTO_DEV_BCM_SPU                       policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_CAVIUM_ZIP                    policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_CCP                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_CCP_CRYPTO                    policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_CCP_DD                        policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_CCP_DEBUGFS                   policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_CRYPTO_DEV_CCREE                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_CHELSIO                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_CPT                           policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_EXYNOS_RNG                    policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_AHASH_API            policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_AHASH_API_DESC       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_COMMON               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API_DESC      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API_QI        policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_DEBUG                policy<{'arm64': 'n', 'armhf-generic': 'n'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_INTC                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_INTC_COUNT_THLD      policy<{'arm64': '255', 'armhf-generic': '255'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_INTC_TIME_THLD       policy<{'arm64': '2048', 'armhf-generic': '2048'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_JR                   policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_PKC_API              policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_RINGSIZE             policy<{'arm64': '9', 'armhf-generic': '9'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_RNG_API              policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_CRYPTO_DEV_FSL_DPAA2_CAAM                policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_HIFN_795X                     policy<{'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_HIFN_795X_RNG                 policy<{'armhf-generic': 'y'}>
+CONFIG_CRYPTO_DEV_HISI_HPRE                     policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_HISI_QM                       policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_HISI_SEC                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_HISI_SEC2                     policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_HISI_TRNG                     policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_HISI_ZIP                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4           policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4_CTS       policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4_ECB       policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_HCU               policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_HCU_HMAC_SHA224   policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_MARVELL                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_MARVELL_CESA                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_MXS_DCP                       policy<{'arm64': 'n', 'armhf-generic': 'n'}>
+CONFIG_CRYPTO_DEV_NITROX                        policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_NITROX_CNN55XX                policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CRYPTO_DEV_NX                            policy<{'ppc64el': 'y'}>
+CONFIG_CRYPTO_DEV_NX_COMPRESS                   policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_NX_COMPRESS_POWERNV           policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_NX_COMPRESS_PSERIES           policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_OCTEONTX2_CPT                 policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_OCTEONTX_CPT                  policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_OMAP                          policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_OMAP_AES                      policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_OMAP_DES                      policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_OMAP_SHAM                     policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_PADLOCK                       policy<{'amd64': 'y'}>
+CONFIG_CRYPTO_DEV_PADLOCK_AES                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_PADLOCK_SHA                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT                           policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_4XXX                      policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_C3XXX                     policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_C3XXXVF                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_C62X                      policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_C62XVF                    policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_DH895xCC                  policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QAT_DH895xCCVF                policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_DEV_QCE                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_QCE_AEAD                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_AEAD               policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_ALL                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_SHA                policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_SKCIPHER           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_CRYPTO_DEV_QCE_SHA                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CRYPTO_DEV_QCE_SKCIPHER                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_CRYPTO_DEV_QCE_SW_MAX_LEN                policy<{'arm64': '512', 'armhf': '512'}>
+CONFIG_CRYPTO_DEV_QCOM_RNG                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_ROCKCHIP                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_S5P                           policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_DEV_SA2UL                         policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_SAFEXCEL                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CRYPTO_DEV_SAHARA                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_CRYPTO_DEV_SP_CCP                        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_SP_PSP                        policy<{'amd64': 'y'}>
+CONFIG_CRYPTO_DEV_SUN4I_SS                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_SUN4I_SS_DEBUG                policy<{'arm64': 'n'}>
+CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_DEBUG                policy<{'arm64': 'n'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_HASH                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_PRNG                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_TRNG                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS_DEBUG                policy<{'arm64': 'n'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS_HASH                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS_PRNG                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_VIRTIO                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_DEV_VMX                           policy<{'ppc64el': 'y'}>
+CONFIG_CRYPTO_DEV_VMX_ENCRYPT                   policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_DEV_ZYNQMP_AES                    policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_DH                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_DRBG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_DRBG_CTR                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_DRBG_HASH                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_DRBG_HMAC                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_DRBG_MENU                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_ECB                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_ECC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ECDH                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ECDSA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ECHAINIV                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ECRDSA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ENGINE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ESSIV                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_FCRYPT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_GCM                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_GF128MUL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_GHASH                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_GHASH_ARM64_CE                    policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_GHASH_ARM_CE                      policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL              policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_GHASH_S390                        policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_HASH                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_HASH2                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_HASH_INFO                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_HMAC                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_HW                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_JITTERENTROPY                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_KEYWRAP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_KPP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_KPP2                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_LIB_AES                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_LIB_ARC4                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_LIB_CHACHA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_CHACHA20POLY1305              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_CHACHA_GENERIC                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_CURVE25519                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_CURVE25519_GENERIC            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_DES                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_POLY1305                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_POLY1305_GENERIC              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LIB_POLY1305_RSIZE                policy<{'amd64': '11', 'arm64': '9', 'armhf': '9', 'ppc64el': '1', 's390x': '1'}>
+CONFIG_CRYPTO_LIB_SHA256                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_LIB_SM4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LRW                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LZ4                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LZ4HC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_LZO                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_MANAGER                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_MANAGER2                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_MANAGER_DISABLE_TESTS             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_MD4                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_MD5                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_MD5_PPC                           policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_MICHAEL_MIC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_NHPOLY1305                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_NHPOLY1305_AVX2                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_NHPOLY1305_NEON                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_NHPOLY1305_SSE2                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_NULL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_NULL2                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_OFB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_PAES_S390                         policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_PCBC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_PCRYPT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_POLY1305                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_POLY1305_ARM                      policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_POLY1305_NEON                     policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_POLY1305_X86_64                   policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_RMD160                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_RNG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_RNG2                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_RNG_DEFAULT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_RSA                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SEQIV                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SERPENT                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_SERPENT_AVX2_X86_64               policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SERPENT_AVX_X86_64                policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SERPENT_SSE2_X86_64               policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SHA1                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SHA1_ARM                          policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_SHA1_ARM64_CE                     policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SHA1_ARM_CE                       policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_SHA1_ARM_NEON                     policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_SHA1_PPC                          policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_SHA1_S390                         policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_SHA1_SSSE3                        policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SHA256                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SHA256_ARM                        policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_SHA256_ARM64                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SHA256_S390                       policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_SHA256_SSSE3                      policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SHA2_ARM64_CE                     policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SHA2_ARM_CE                       policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_SHA3                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_SHA3_256_S390                     policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_SHA3_512_S390                     policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_SHA3_ARM64                        policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SHA512_ARM                        policy<{'armhf': 'm'}>
+CONFIG_CRYPTO_SHA512_ARM64                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SHA512_ARM64_CE                   policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SHA512_S390                       policy<{'s390x': 'm'}>
+CONFIG_CRYPTO_SHA512_SSSE3                      policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SIMD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_CRYPTO_SKCIPHER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SKCIPHER2                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_SM2                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_SM3                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_SM3_ARM64_CE                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_SM4                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_SM4_AESNI_AVX2_X86_64             policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SM4_AESNI_AVX_X86_64              policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_SM4_ARM64_CE                      policy<{'arm64': 'm'}>
+CONFIG_CRYPTO_STATS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_STREEBOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_TEST                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_TWOFISH                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_TWOFISH_AVX_X86_64                policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_TWOFISH_COMMON                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_TWOFISH_X86_64                    policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_TWOFISH_X86_64_3WAY               policy<{'amd64': 'm'}>
+CONFIG_CRYPTO_USER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_USER_API                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_USER_API_AEAD                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_USER_API_HASH                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_USER_API_RNG                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_USER_API_RNG_CAVP                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CRYPTO_USER_API_SKCIPHER                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_VMAC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_VPMSUM_TESTER                     policy<{'ppc64el': 'm'}>
+CONFIG_CRYPTO_WP512                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_XCBC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_XTS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_CRYPTO_XXHASH                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CRYPTO_ZSTD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CS89x0                                   policy<{'armhf': 'm'}>
+CONFIG_CS89x0_PLATFORM                          policy<{'armhf': 'm'}>
+CONFIG_CSD_LOCK_WAIT_DEBUG                      policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_CTCM                                     policy<{'s390x': 'm'}>
+CONFIG_CUSE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_CW1200                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CW1200_WLAN_SDIO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CW1200_WLAN_SPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CXD2880_SPI_DRV                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CXL                                      policy<{'ppc64el': 'm'}>
+CONFIG_CXLFLASH                                 policy<{'ppc64el': 'm'}>
+CONFIG_CXL_ACPI                                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_CXL_BASE                                 policy<{'ppc64el': 'y'}>
+CONFIG_CXL_BUS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_CXL_MEM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_CXL_MEM_RAW_COMMANDS                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_CXL_PMEM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_CX_ECAT                                  policy<{'amd64': 'm'}>
+CONFIG_CYPRESS_FIRMWARE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA280                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA311                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA9052_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA9055_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA9062_THERMAL                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA9062_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA9063_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DA9150_GPADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DAMON                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DASD                                     policy<{'s390x': 'm'}>
+CONFIG_DASD_DIAG                                policy<{'s390x': 'm'}>
+CONFIG_DASD_ECKD                                policy<{'s390x': 'm'}>
+CONFIG_DASD_EER                                 policy<{'s390x': 'y'}>
+CONFIG_DASD_FBA                                 policy<{'s390x': 'm'}>
+CONFIG_DASD_PROFILE                             policy<{'s390x': 'y'}>
+CONFIG_DATA_SHIFT                               policy<{'ppc64el': '24'}>
+CONFIG_DAVICOM_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DAX                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DAX_DRIVER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DCA                                      policy<{'amd64': 'm'}>
+CONFIG_DCACHE_WORD_ACCESS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DCB                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DCDBAS                                   policy<{'amd64': 'm'}>
+CONFIG_DCSSBLK                                  policy<{'s390x': 'm'}>
+CONFIG_DDR                                      policy<{'armhf': 'y'}>
+CONFIG_DE2104X                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DE2104X_DSL                              policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_DE4X5                                    policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_DEBUGGER                                 policy<{'ppc64el': 'y'}>
+CONFIG_DEBUG_ALIGN_RODATA                       policy<{'armhf': 'y'}>
+CONFIG_DEBUG_ATOMIC_SLEEP                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_BOOT_PARAMS                        policy<{'amd64': 'n'}>
+CONFIG_DEBUG_BUGVERBOSE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_CREDENTIALS                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_DEVRES                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_DRIVER                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_EFI                                policy<{'arm64': 'n'}>
+CONFIG_DEBUG_ENTRY                              policy<{'amd64': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B           policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n'}>
+CONFIG_DEBUG_FORCE_WEAK_PER_CPU                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_FS_ALLOW_ALL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_FS_ALLOW_NONE                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_FS_DISALLOW_MOUNT                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_GPIO                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_HIGHMEM                            policy<{'armhf': 'n'}>
+CONFIG_DEBUG_HOTPLUG_CPU0                       policy<{'amd64': 'n'}>
+CONFIG_DEBUG_INFO_BTF_MODULES                   policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_INFO_COMPRESSED                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_INFO_DWARF4                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_INFO_DWARF5                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_INFO_REDUCED                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_IRQFLAGS                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_KERNEL_DC                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DEBUG_KMAP_LOCAL                         policy<{'armhf': 'n'}>
+CONFIG_DEBUG_KMEMLEAK                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_KOBJECT                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_LIST                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_LL                                 policy<{'armhf': 'n'}>
+CONFIG_DEBUG_LL_INCLUDE                         policy<{'armhf': '"mach/debug-macro.S"'}>
+CONFIG_DEBUG_LOCKING_API_SELFTESTS              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_LOCK_ALLOC                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_MEMORY_INIT                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_MISC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEBUG_MUTEXES                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_NMI_SELFTEST                       policy<{'amd64': 'n'}>
+CONFIG_DEBUG_NOTIFIERS                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_OBJECTS                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_PAGEALLOC                          policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_PAGE_REF                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_PERF_USE_VMALLOC                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_PER_CPU_MAPS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_PINCTRL                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DEBUG_PLIST                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_PREEMPT                            policy<{'amd64-lowlatency': 'n', 'arm64-lowlatency': 'n', 'arm64-lowlatency-64k': 'n'}>
+CONFIG_DEBUG_RODATA_TEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_RSEQ                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_RT_MUTEXES                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_RWSEMS                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_SECTION_MISMATCH                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_SG                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_SHIRQ                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_SPINLOCK                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_STACKOVERFLOW                      policy<{'ppc64el': 'n'}>
+CONFIG_DEBUG_STACK_USAGE                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_TEST_DRIVER_REMOVE                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_TIMEKEEPING                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_TLBFLUSH                           policy<{'amd64': 'n'}>
+CONFIG_DEBUG_USER                               policy<{'armhf': 'n'}>
+CONFIG_DEBUG_VF_UART_PORT                       policy<{'armhf-generic': '1'}>
+CONFIG_DEBUG_VIRTUAL                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DEBUG_VM                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_VM_PGTABLE                         policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_WQ_FORCE_RR_CPU                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_WW_MUTEX_SLOWPATH                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEBUG_WX                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_BZIP2                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_GZIP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_LZ4                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_LZMA                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_LZO                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_XZ                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DECOMPRESS_ZSTD                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEFAULT_CUBIC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEFAULT_HOSTNAME                         policy<{'amd64': '"(none)"', 'arm64': '"(none)"', 'armhf': '"(none)"', 'ppc64el': '"(none)"', 's390x': '"(none)"'}>
+CONFIG_DEFAULT_HUNG_TASK_TIMEOUT                policy<{'amd64': '120', 'arm64': '120', 'armhf': '120', 'ppc64el': '120', 's390x': '120'}>
+CONFIG_DEFAULT_INIT                             policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_DEFAULT_RENO                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEFAULT_SECURITY_APPARMOR                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEFAULT_SECURITY_DAC                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEFAULT_SECURITY_SELINUX                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEFAULT_SECURITY_SMACK                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEFAULT_SECURITY_TOMOYO                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEFAULT_TCP_CONG                         policy<{'amd64': '"cubic"', 'arm64': '"cubic"', 'armhf': '"cubic"', 'ppc64el': '"cubic"', 's390x': '"cubic"'}>
+CONFIG_DEFERRED_STRUCT_PAGE_INIT                policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DEFXX                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DELL_LAPTOP                              policy<{'amd64': 'm'}>
+CONFIG_DELL_RBTN                                policy<{'amd64': 'm'}>
+CONFIG_DELL_RBU                                 policy<{'amd64': 'm'}>
+CONFIG_DELL_SMBIOS                              policy<{'amd64': 'm'}>
+CONFIG_DELL_SMBIOS_SMM                          policy<{'amd64': 'y'}>
+CONFIG_DELL_SMBIOS_WMI                          policy<{'amd64': 'y'}>
+CONFIG_DELL_SMO8800                             policy<{'amd64': 'm'}>
+CONFIG_DELL_UART_BACKLIGHT                      policy<{'amd64': 'm'}>
+CONFIG_DELL_WMI                                 policy<{'amd64': 'm'}>
+CONFIG_DELL_WMI_AIO                             policy<{'amd64': 'm'}>
+CONFIG_DELL_WMI_DESCRIPTOR                      policy<{'amd64': 'm'}>
+CONFIG_DELL_WMI_LED                             policy<{'amd64': 'm'}>
+CONFIG_DELL_WMI_PRIVACY                         policy<{'amd64': 'y'}>
+CONFIG_DELL_WMI_SYSMAN                          policy<{'amd64': 'm'}>
+CONFIG_DEPRECATED_PARAM_STRUCT                  policy<{'armhf': 'n'}>
+CONFIG_DETECT_HUNG_TASK                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEVFREQ_EVENT_EXYNOS_NOCP                policy<{'armhf': 'y'}>
+CONFIG_DEVFREQ_EVENT_EXYNOS_PPMU                policy<{'armhf': 'y'}>
+CONFIG_DEVFREQ_EVENT_ROCKCHIP_DFI               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DEVFREQ_GOV_PASSIVE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVFREQ_GOV_PERFORMANCE                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVFREQ_GOV_POWERSAVE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVFREQ_GOV_USERSPACE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVFREQ_THERMAL                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVICE_PRIVATE                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_DEVMEM                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEVPORT                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DEV_APPLETALK                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DEV_COREDUMP                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DEV_DAX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DEV_DAX_HMEM                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_DEV_DAX_HMEM_DEVICES                     policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_DEV_DAX_KMEM                             policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DEV_DAX_PMEM                             policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_DEV_DAX_PMEM_COMPAT                      policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_DEV_PAGEMAP_OPS                          policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_DHT11                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DIAG288_WATCHDOG                         policy<{'s390x': 'm'}>
+CONFIG_DIMLIB                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DL2K                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DLHL60D                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DLM                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DLM_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DLN2_ADC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DM9000                                   policy<{'armhf': 'm'}>
+CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL             policy<{'armhf': 'n'}>
+CONFIG_DM9102                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DMABUF_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMABUF_HEAPS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DMABUF_HEAPS_CMA                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DMABUF_HEAPS_SYSTEM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DMABUF_MOVE_NOTIFY                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMABUF_SELFTESTS                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMABUF_SYSFS_STATS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMADEVICES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_DMADEVICES_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DMARD06                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DMARD09                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DMARD10                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DMAR_TABLE                               policy<{'amd64': 'y'}>
+CONFIG_DMATEST                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DMA_ACPI                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_DMA_API_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMA_BCM2835                              policy<{'arm64': 'y'}>
+CONFIG_DMA_COHERENT_POOL                        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_DMA_DECLARE_COHERENT                     policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DMA_DIRECT_REMAP                         policy<{'arm64': 'y'}>
+CONFIG_DMA_ENGINE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DMA_ENGINE_RAID                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DMA_FENCE_TRACE                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMA_MAP_BENCHMARK                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DMA_NONCOHERENT_MMAP                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DMA_OF                                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DMA_OMAP                                 policy<{'armhf': 'y'}>
+CONFIG_DMA_OPS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DMA_OPS_BYPASS                           policy<{'ppc64el': 'y'}>
+CONFIG_DMA_PERNUMA_CMA                          policy<{'arm64': 'y', 'armhf': 'n'}>
+CONFIG_DMA_REMAP                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DMA_RESTRICTED_POOL                      policy<{'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y'}>
+CONFIG_DMA_SHARED_BUFFER                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DMA_SUN6I                                policy<{'arm64': 'm'}>
+CONFIG_DMA_VIRTUAL_CHANNELS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_DMI                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DMIID                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DMI_SCAN_MACHINE_NON_EFI_FALLBACK        policy<{'amd64': 'y'}>
+CONFIG_DMI_SYSFS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DM_BIO_PRISON                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_BUFIO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_CACHE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_CACHE_SMQ                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_CLONE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_CRYPT                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_DEBUG                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_DM_DEBUG_BLOCK_MANAGER_LOCKING           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DM_DELAY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_DUST                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DM_EBS                                   policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_ERA                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_FLAKEY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_INIT                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DM_INTEGRITY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_LOG_USERSPACE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_LOG_WRITES                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_MIRROR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_MULTIPATH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_MULTIPATH_HST                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_MULTIPATH_IOA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_MULTIPATH_QL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_MULTIPATH_ST                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_PERSISTENT_DATA                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_RAID                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_SNAPSHOT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_SWITCH                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_THIN_PROVISIONING                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_UEVENT                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DM_UNSTRIPED                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_VERITY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_VERITY_FEC                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DM_WRITECACHE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_ZERO                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DM_ZONED                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DNET                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DNOTIFY                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DNS_RESOLVER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DOVE_CLK                                 policy<{'armhf': 'y'}>
+CONFIG_DOVE_THERMAL                             policy<{'armhf': 'm'}>
+CONFIG_DP83640_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DP83822_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DP83848_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DP83867_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DP83869_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DP83TC811_PHY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DPAA2_CONSOLE                            policy<{'arm64': 'm'}>
+CONFIG_DPAA_ERRATUM_A050385                     policy<{'arm64': 'y'}>
+CONFIG_DPM_WATCHDOG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DPOT_DAC                                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DPS310                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DPTF_PCH_FIVR                            policy<{'amd64': 'm'}>
+CONFIG_DPTF_POWER                               policy<{'amd64': 'm'}>
+CONFIG_DQL                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRA752_THERMAL                           policy<{'armhf': 'y'}>
+CONFIG_DRAGONRISE_FF                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRBD_FAULT_INJECTION                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DRM                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_AMDGPU                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_AMDGPU_SI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMDGPU_USERPTR                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMD_ACP                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMD_DC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMD_DC_DCN                           policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMD_DC_HDCP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMD_DC_SI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_AMD_SECURE_DISPLAY                   policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_ANALOGIX_ANX6345                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_ANALOGIX_ANX7625                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_ANALOGIX_ANX78XX                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_ANALOGIX_DP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_ARCPGU                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_ARMADA                               policy<{'armhf': 'm'}>
+CONFIG_DRM_ASPEED_GFX                           policy<{'armhf': 'm'}>
+CONFIG_DRM_AST                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_ATMEL_HLCDC                          policy<{'armhf': 'm'}>
+CONFIG_DRM_BOCHS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_BRIDGE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRM_CDNS_DSI                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_CDNS_MHDP8546                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_CDNS_MHDP8546_J721E                  policy<{'arm64': 'y'}>
+CONFIG_DRM_CHIPONE_ICN6211                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_CHRONTEL_CH7033                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_CIRRUS_QEMU                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_CROS_EC_ANX7688                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_DEBUG_DP_MST_TOPOLOGY_REFS           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DRM_DEBUG_SELFTEST                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DRM_DISPLAY_CONNECTOR                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_DP_AUX_BUS                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_DP_AUX_CHARDEV                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_DRM_DP_CEC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_DRM_DW_HDMI                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_DW_HDMI_AHB_AUDIO                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_DW_HDMI_CEC                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_DW_HDMI_I2S_AUDIO                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_DW_MIPI_DSI                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_ETNAVIV                              policy<{'amd64': 'n', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DRM_ETNAVIV_THERMAL                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_EXYNOS                               policy<{'armhf': 'm'}>
+CONFIG_DRM_EXYNOS5433_DECON                     policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS7_DECON                        policy<{'armhf': 'n'}>
+CONFIG_DRM_EXYNOS_DSI                           policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_FIMC                          policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_FIMD                          policy<{'armhf': 'n'}>
+CONFIG_DRM_EXYNOS_HDMI                          policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_IPP                           policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_MIC                           policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_MIXER                         policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_ROTATOR                       policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_SCALER                        policy<{'armhf': 'y'}>
+CONFIG_DRM_EXYNOS_VIDI                          policy<{'armhf': 'n'}>
+CONFIG_DRM_FBDEV_EMULATION                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_DRM_FBDEV_OVERALLOC                      policy<{'amd64': '100', 'arm64': '100', 'armhf': '100', 'ppc64el': '100', 's390x': '100'}>
+CONFIG_DRM_FSL_DCU                              policy<{'armhf': 'm'}>
+CONFIG_DRM_GEM_CMA_HELPER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_GEM_SHMEM_HELPER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRM_GM12U320                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_GMA500                               policy<{'amd64': 'm'}>
+CONFIG_DRM_GUD                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_HDLCD                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_HDLCD_SHOW_UNDERRUN                  policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_DRM_HISI_KIRIN                           policy<{'arm64': 'm'}>
+CONFIG_DRM_HYPERV                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_DRM_I2C_ADV7511                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_I2C_ADV7511_AUDIO                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_I2C_ADV7511_CEC                      policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_I2C_CH7006                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_I2C_NXP_TDA9950                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_I2C_NXP_TDA998X                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_I2C_SIL164                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_I915                                 policy<{'amd64': 'm'}>
+CONFIG_DRM_I915_CAPTURE_ERROR                   policy<{'amd64': 'y'}>
+CONFIG_DRM_I915_COMPRESS_ERROR                  policy<{'amd64': 'y'}>
+CONFIG_DRM_I915_DEBUG                           policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_DEBUG_GUC                       policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_DEBUG_MMIO                      policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_DEBUG_RUNTIME_PM                policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_DEBUG_VBLANK_EVADE              policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_FENCE_TIMEOUT                   policy<{'amd64': '10000'}>
+CONFIG_DRM_I915_FORCE_PROBE                     policy<{'amd64': '""'}>
+CONFIG_DRM_I915_GVT                             policy<{'amd64': 'y'}>
+CONFIG_DRM_I915_GVT_KVMGT                       policy<{'amd64': 'm'}>
+CONFIG_DRM_I915_HEARTBEAT_INTERVAL              policy<{'amd64': '2500'}>
+CONFIG_DRM_I915_LOW_LEVEL_TRACEPOINTS           policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_MAX_REQUEST_BUSYWAIT            policy<{'amd64': '8000'}>
+CONFIG_DRM_I915_PREEMPT_TIMEOUT                 policy<{'amd64': '640'}>
+CONFIG_DRM_I915_REQUEST_TIMEOUT                 policy<{'amd64': '20000'}>
+CONFIG_DRM_I915_SELFTEST                        policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_STOP_TIMEOUT                    policy<{'amd64': '100'}>
+CONFIG_DRM_I915_SW_FENCE_CHECK_DAG              policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_SW_FENCE_DEBUG_OBJECTS          policy<{'amd64': 'n'}>
+CONFIG_DRM_I915_TIMESLICE_DURATION              policy<{'amd64': '1'}>
+CONFIG_DRM_I915_USERFAULT_AUTOSUSPEND           policy<{'amd64': '250'}>
+CONFIG_DRM_I915_USERPTR                         policy<{'amd64': 'y'}>
+CONFIG_DRM_I915_WERROR                          policy<{'amd64': 'n'}>
+CONFIG_DRM_IMX                                  policy<{'armhf': 'm'}>
+CONFIG_DRM_IMX_DCSS                             policy<{'arm64': 'm'}>
+CONFIG_DRM_IMX_HDMI                             policy<{'armhf': 'm'}>
+CONFIG_DRM_IMX_LDB                              policy<{'armhf': 'm'}>
+CONFIG_DRM_IMX_PARALLEL_DISPLAY                 policy<{'armhf': 'm'}>
+CONFIG_DRM_IMX_TVE                              policy<{'armhf': 'm'}>
+CONFIG_DRM_ITE_IT66121                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_KMB_DISPLAY                          policy<{'arm64': 'm'}>
+CONFIG_DRM_KMS_CMA_HELPER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_KMS_HELPER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_KOMEDA                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_LIMA                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_LOAD_EDID_FIRMWARE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRM_LONTIUM_LT8912B                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_LONTIUM_LT9611                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_LONTIUM_LT9611UXC                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_LVDS_CODEC                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_MALI_DISPLAY                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_MCDE                                 policy<{'armhf': 'm'}>
+CONFIG_DRM_MEDIATEK                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_MEDIATEK_HDMI                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_MESON                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_MESON_DW_HDMI                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_MIPI_DBI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_MIPI_DSI                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_MSM                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_MSM_DP                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI_10NM_PHY                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI_14NM_PHY                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI_20NM_PHY                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI_28NM_8960_PHY                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI_28NM_PHY                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_DSI_7NM_PHY                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_GPU_STATE                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_GPU_SUDO                         policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_DRM_MSM_HDMI_HDCP                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_MSM_REGISTER_LOGGING                 policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_DRM_MXS                                  policy<{'arm64': 'y', 'armhf-generic': 'y', 'armhf-generic-lpae': '-', 'ppc64el': '-'}>
+CONFIG_DRM_MXSFB                                policy<{'arm64': 'm', 'armhf-generic': 'm', 'armhf-generic-lpae': '-', 'ppc64el': '-'}>
+CONFIG_DRM_NOUVEAU                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_NOUVEAU_BACKLIGHT                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DRM_NOUVEAU_SVM                          policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n'}>
+CONFIG_DRM_NWL_MIPI_DSI                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_NXP_PTN3460                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_OMAP                                 policy<{'armhf': 'n'}>
+CONFIG_DRM_PANEL                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRM_PANEL_ABT_Y030XX067A                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ARM_VERSATILE                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ASUS_Z00T_TM5P5_NT35596        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_BOE_HIMAX8279D                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_BOE_TV101WUM_NL6               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_BRIDGE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DRM_PANEL_DSI_CM                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ELIDA_KD35T133                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ILITEK_IL9322                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ILITEK_ILI9341                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ILITEK_ILI9881C                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_INNOLUX_EJ030NA                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_INNOLUX_P079ZCA                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_JDI_LT070ME05000               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_KHADAS_TS050                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_KINGDISPLAY_KD097D04           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_LEADTEK_LTK050H3146W           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_LG_LB035Q02                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_LG_LG4573                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_LVDS                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_MANTIX_MLAF057WE51             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_NEC_NL8048HL11                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_NOVATEK_NT35510                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_NOVATEK_NT36672A               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_NOVATEK_NT39016                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_ORIENTATION_QUIRKS             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_PANEL_ORISETECH_OTM8009A             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_OSD_OSD101T2587_53TS           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_RAYDIUM_RM67191                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_RAYDIUM_RM68200                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_RONBO_RB070D30                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_DB7430                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_LD9040                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6D16D0                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E63M0                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E63M0_DSI            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E63M0_SPI            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E88A0_AMS452EF01     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SAMSUNG_SOFEF00                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SEIKO_43WVF1G                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SHARP_LQ101R1SX01              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SHARP_LS037V7DW01              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SHARP_LS043T1LE01              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SIMPLE                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SITRONIX_ST7701                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SITRONIX_ST7703                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SITRONIX_ST7789V               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SONY_ACX424AKP                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_SONY_ACX565AKM                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_TDO_TL070WSH30                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_TPO_TD028TTEC1                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_TPO_TD043MTEA1                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_TPO_TPG110                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_VISIONOX_RM69299               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_WIDECHIPS_WS2401               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANEL_XINPENG_XPP055C272             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PANFROST                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_PARADE_PS8622                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PARADE_PS8640                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_PL111                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_QXL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_RADEON                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_RADEON_USERPTR                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DRM_RCAR_CMM                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_RCAR_DU                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_RCAR_DW_HDMI                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_RCAR_LVDS                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': '-'}>
+CONFIG_DRM_RCAR_USE_CMM                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_RCAR_USE_LVDS                        policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n'}>
+CONFIG_DRM_RCAR_VSP                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DRM_RCAR_WRITEBACK                       policy<{'arm64': 'y'}>
+CONFIG_DRM_ROCKCHIP                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_SCHED                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_SII902X                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_SII9234                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_SIL_SII8620                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_SIMPLEDRM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_SIMPLE_BRIDGE                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_STM                                  policy<{'armhf': 'm'}>
+CONFIG_DRM_STM_DSI                              policy<{'armhf': 'm'}>
+CONFIG_DRM_SUN4I                                policy<{'arm64': 'm'}>
+CONFIG_DRM_SUN4I_BACKEND                        policy<{'arm64': 'm'}>
+CONFIG_DRM_SUN4I_HDMI                           policy<{'arm64': 'm'}>
+CONFIG_DRM_SUN4I_HDMI_CEC                       policy<{'arm64': 'y'}>
+CONFIG_DRM_SUN6I_DSI                            policy<{'arm64': 'm'}>
+CONFIG_DRM_SUN8I_DW_HDMI                        policy<{'arm64': 'm'}>
+CONFIG_DRM_SUN8I_MIXER                          policy<{'arm64': 'm'}>
+CONFIG_DRM_SUN8I_TCON_TOP                       policy<{'arm64': 'm'}>
+CONFIG_DRM_TEGRA                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_DRM_TEGRA_DEBUG                          policy<{'arm64': 'n', 'armhf-generic': 'n'}>
+CONFIG_DRM_TEGRA_STAGING                        policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_DRM_THINE_THC63LVD1024                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TIDSS                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DRM_TILCDC                               policy<{'armhf': 'm'}>
+CONFIG_DRM_TI_SN65DSI83                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TI_SN65DSI86                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TI_TFP410                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TI_TPD12S015                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TOSHIBA_TC358762                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TOSHIBA_TC358764                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TOSHIBA_TC358767                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TOSHIBA_TC358768                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TOSHIBA_TC358775                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_TTM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_TTM_HELPER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_TVE200                               policy<{'armhf': 'm'}>
+CONFIG_DRM_UDL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DRM_VC4                                  policy<{'arm64': 'm'}>
+CONFIG_DRM_VC4_HDMI_CEC                         policy<{'arm64': 'y'}>
+CONFIG_DRM_VGEM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_VIRTIO_GPU                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_VKMS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DRM_VMWGFX                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_DRM_VMWGFX_FBCON                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_DRM_VMWGFX_MKSSTATS                      policy<{'amd64': 'n'}>
+CONFIG_DRM_VRAM_HELPER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DRM_XEN                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_DRM_XEN_FRONTEND                         policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_DRM_ZYNQMP_DPSUB                         policy<{'arm64': 'm'}>
+CONFIG_DS1682                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DS1803                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DS4424                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DST_CACHE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DTC                                      policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DTL                                      policy<{'ppc64el': 'y'}>
+CONFIG_DTPM                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DTPM_CPU                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DT_IDLE_STATES                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DUMMY                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DUMMY_CONSOLE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DUMMY_CONSOLE_COLUMNS                    policy<{'amd64': '80', 'arm64': '80', 'ppc64el': '80', 's390x': '80'}>
+CONFIG_DUMMY_CONSOLE_ROWS                       policy<{'amd64': '25', 'arm64': '25', 'ppc64el': '25', 's390x': '25'}>
+CONFIG_DUMMY_IRQ                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DVB_A8293                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AF9013                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AF9033                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AS102                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AS102_FE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ASCOT2E                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ATBM8830                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AU8522                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AU8522_DTV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AU8522_V4L                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AV7110                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_AV7110_IR                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_AV7110_OSD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_B2C2_FLEXCOP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_B2C2_FLEXCOP_PCI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_B2C2_FLEXCOP_PCI_DEBUG               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_B2C2_FLEXCOP_USB                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_B2C2_FLEXCOP_USB_DEBUG               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_BCM3510                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_BT8XX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_BUDGET                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_BUDGET_AV                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_BUDGET_CI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_BUDGET_CORE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_BUDGET_PATCH                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_C8SECTPFE                            policy<{'armhf': 'n'}>
+CONFIG_DVB_CORE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX22700                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX22702                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX24110                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX24116                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX24117                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX24120                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CX24123                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CXD2099                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CXD2820R                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CXD2841ER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_CXD2880                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DDBRIDGE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DDBRIDGE_MSIENABLE                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_DEMUX_SECTION_LOSS_LOG               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_DIB3000MB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DIB3000MC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DIB7000M                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DIB7000P                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DIB8000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DIB9000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DM1105                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DRX39XYJ                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DRXD                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DRXK                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DS3000                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_DYNAMIC_MINORS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_EC100                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_FIREDTV                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_FIREDTV_INPUT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_GP8PSK_FE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_HELENE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_HOPPER                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_HORUS3A                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ISL6405                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ISL6421                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ISL6423                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_IX2505V                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_L64781                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LG2160                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LGDT3305                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LGDT3306A                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LGDT330X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LGS8GL5                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LGS8GXX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LNBH25                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LNBH29                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LNBP21                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_LNBP22                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_M88DS3103                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_M88RS2000                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MANTIS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MAX_ADAPTERS                         policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8'}>
+CONFIG_DVB_MB86A16                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MB86A20S                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MMAP                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_MN88443X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MN88472                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MN88473                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MT312                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MT352                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MXL5XX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_MXL692                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_NET                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_NETUP_UNIDVB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_NGENE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_NXT200X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_NXT6000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_OR51132                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_OR51211                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_PLATFORM_DRIVERS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_PLL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_PLUTO2                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_PT1                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_PT3                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_RTL2830                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_RTL2832                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_RTL2832_SDR                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_S5H1409                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_S5H1411                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_S5H1420                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_S5H1432                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_S921                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SI2165                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SI2168                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SI21XX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SMIPCIE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SP2                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SP8870                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_SP887X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STB0899                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STB6000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STB6100                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV0288                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV0297                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV0299                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV0367                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV0900                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV090x                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV0910                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV6110                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV6110x                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_STV6111                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TC90522                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA10021                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA10023                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA10048                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA1004X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA10071                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA10086                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA18271C2DD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA665x                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA8083                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA8261                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TDA826X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TEST_DRIVERS                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_TS2020                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TTUSB_BUDGET                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TTUSB_DEC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TUA6100                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TUNER_CX24113                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TUNER_DIB0070                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TUNER_DIB0090                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_TUNER_ITD1000                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ULE_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_USB                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_A800                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AF9005                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AF9005_REMOTE                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AF9015                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AF9035                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_ANYSEE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AU6610                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AZ6007                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_AZ6027                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_CE6230                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_CINERGY_T2                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_CXUSB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_CXUSB_ANALOG                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_DVB_USB_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_USB_DIB0700                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DIB3000MC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DIBUSB_MB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DIBUSB_MB_FAULTY                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_DVB_USB_DIBUSB_MC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DIGITV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DTT200U                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DTV5100                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DVBSKY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_DW2102                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_EC168                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_GL861                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_GP8PSK                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_LME2510                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_M920X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_MXL111SF                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_NOVA_T_USB2                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_OPERA1                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_PCTV452E                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_RTL28XXU                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_TECHNISAT_USB2                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_TTUSB2                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_UMT_010                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_V2                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_VP702X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_VP7045                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_USB_ZD1301                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_VES1820                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_VES1X93                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ZD1301_DEMOD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ZL10036                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ZL10039                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DVB_ZL10353                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DWC_XLGMAC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DWC_XLGMAC_PCI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_DWMAC_DWC_QOS_ETH                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DWMAC_GENERIC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DWMAC_IMX8                               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_DWMAC_INTEL                              policy<{'amd64': 'm'}>
+CONFIG_DWMAC_INTEL_PLAT                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DWMAC_IPQ806X                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DWMAC_MEDIATEK                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DWMAC_MESON                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DWMAC_QCOM_ETHQOS                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DWMAC_ROCKCHIP                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DWMAC_SOCFPGA                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_DWMAC_SUN8I                              policy<{'arm64': 'm'}>
+CONFIG_DWMAC_SUNXI                              policy<{'arm64': 'n'}>
+CONFIG_DWMAC_VISCONTI                           policy<{'arm64': 'm'}>
+CONFIG_DW_APB_ICTL                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DW_APB_TIMER                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DW_APB_TIMER_OF                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_DW_AXI_DMAC                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_DMAC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_DMAC_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_DMAC_PCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_EDMA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_EDMA_PCIE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_I3C_MASTER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_DW_WATCHDOG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DW_XDATA_PCIE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_DYNAMIC_DEBUG                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DYNAMIC_DEBUG_CORE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DYNAMIC_EVENTS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DYNAMIC_FTRACE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DYNAMIC_FTRACE_WITH_ARGS                 policy<{'amd64': 'y'}>
+CONFIG_DYNAMIC_FTRACE_WITH_DIRECT_CALLS         policy<{'amd64': 'y'}>
+CONFIG_DYNAMIC_FTRACE_WITH_REGS                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_DYNAMIC_MEMORY_LAYOUT                    policy<{'amd64': 'y'}>
+CONFIG_DYNAMIC_PHYSICAL_MASK                    policy<{'amd64': 'y'}>
+CONFIG_DYNAMIC_SIGFRAME                         policy<{'amd64': 'y'}>
+CONFIG_E100                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_E1000                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_E1000E                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_E1000E_HWTS                              policy<{'amd64': 'y'}>
+CONFIG_EADM_SCH                                 policy<{'s390x': 'm'}>
+CONFIG_EARLY_PRINTK                             policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EARLY_PRINTK_DBGP                        policy<{'amd64': 'y'}>
+CONFIG_EARLY_PRINTK_USB                         policy<{'amd64': 'y'}>
+CONFIG_EARLY_PRINTK_USB_XDBC                    policy<{'amd64': 'y'}>
+CONFIG_EBC_C384_WDT                             policy<{'amd64': 'm'}>
+CONFIG_ECHO                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ECRYPT_FS_MESSAGING                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EDAC                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_EDAC_ALTERA                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_ETHERNET                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_L2C                          policy<{'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_NAND                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_OCRAM                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_QSPI                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_SDMMC                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_SDRAM                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_ALTERA_USB                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EDAC_AL_MC                               policy<{'armhf': 'm'}>
+CONFIG_EDAC_AMD64                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_ARMADA_XP                           policy<{'armhf': 'y'}>
+CONFIG_EDAC_ASPEED                              policy<{'armhf': 'm'}>
+CONFIG_EDAC_ATOMIC_SCRUB                        policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_EDAC_BLUEFIELD                           policy<{'arm64': 'm'}>
+CONFIG_EDAC_CPC925                              policy<{'ppc64el': 'm'}>
+CONFIG_EDAC_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_EDAC_DECODE_MCE                          policy<{'amd64': 'm'}>
+CONFIG_EDAC_DMC520                              policy<{'arm64': 'm'}>
+CONFIG_EDAC_E752X                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_GHES                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_EDAC_HIGHBANK_L2                         policy<{'armhf': 'm'}>
+CONFIG_EDAC_HIGHBANK_MC                         policy<{'armhf': 'm'}>
+CONFIG_EDAC_I10NM                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I3000                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I3200                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I5000                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I5100                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I5400                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I7300                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_I7CORE                              policy<{'amd64': 'm'}>
+CONFIG_EDAC_I82975X                             policy<{'amd64': 'm'}>
+CONFIG_EDAC_IE31200                             policy<{'amd64': 'm'}>
+CONFIG_EDAC_IGEN6                               policy<{'amd64': 'm'}>
+CONFIG_EDAC_LAYERSCAPE                          policy<{'arm64': 'm'}>
+CONFIG_EDAC_LEGACY_SYSFS                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_EDAC_PND2                                policy<{'amd64': 'm'}>
+CONFIG_EDAC_QCOM                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EDAC_SBRIDGE                             policy<{'amd64': 'm'}>
+CONFIG_EDAC_SKX                                 policy<{'amd64': 'm'}>
+CONFIG_EDAC_SUPPORT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_EDAC_SYNOPSYS                            policy<{'arm64': 'm'}>
+CONFIG_EDAC_THUNDERX                            policy<{'arm64': 'm'}>
+CONFIG_EDAC_TI                                  policy<{'armhf': 'm'}>
+CONFIG_EDAC_X38                                 policy<{'amd64': 'm'}>
+CONFIG_EDAC_XGENE                               policy<{'arm64': 'm'}>
+CONFIG_EDD                                      policy<{'amd64': 'y'}>
+CONFIG_EDD_OFF                                  policy<{'amd64': 'y'}>
+CONFIG_EEEPC_LAPTOP                             policy<{'amd64': 'm'}>
+CONFIG_EEEPC_WMI                                policy<{'amd64': 'm'}>
+CONFIG_EEH                                      policy<{'ppc64el': 'y'}>
+CONFIG_EEPROM_93CX6                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EEPROM_93XX46                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EEPROM_AT24                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EEPROM_AT25                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EEPROM_EE1004                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EEPROM_IDT_89HPESX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EEPROM_LEGACY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EEPROM_MAX6875                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EFI                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_ARMSTUB_DTB_LOADER                   policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_EFI_BOOTLOADER_CONTROL                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EFI_CAPSULE_LOADER                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EFI_CUSTOM_SSDT_OVERLAYS                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_EFI_DEV_PATH_PARSER                      policy<{'amd64': 'y'}>
+CONFIG_EFI_DISABLE_PCI_DMA                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n'}>
+CONFIG_EFI_EARLYCON                             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_EFI_EMBEDDED_FIRMWARE                    policy<{'amd64': 'y'}>
+CONFIG_EFI_ESRT                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_FAKE_MEMMAP                          policy<{'amd64': 'n'}>
+CONFIG_EFI_GENERIC_STUB                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_GENERIC_STUB_INITRD_CMDLINE_LOADER   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_MIXED                                policy<{'amd64': 'y'}>
+CONFIG_EFI_PARAMS_FROM_FDT                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EFI_PGT_DUMP                             policy<{'amd64': 'n'}>
+CONFIG_EFI_RCI2_TABLE                           policy<{'amd64': 'y'}>
+CONFIG_EFI_RUNTIME_MAP                          policy<{'amd64': 'y'}>
+CONFIG_EFI_RUNTIME_WRAPPERS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_SOFT_RESERVE                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_EFI_STUB                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_EFI_TEST                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EFI_VARS_PSTORE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n'}>
+CONFIG_EFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EINT_MTK                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ELFCORE                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ELF_CORE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EMAC_ROCKCHIP                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EMBEDDED                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_EM_TIMER_STI                             policy<{'armhf': 'y'}>
+CONFIG_ENA_ETHERNET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ENC28J60                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ENC28J60_WRITEVERIFY                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ENCLOSURE_SERVICES                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ENCRYPTED_KEYS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ENCX24J600                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ENERGY_MODEL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ENIC                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ENVELOPE_DETECTOR                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EPAPR_BOOT                               policy<{'ppc64el': 'y'}>
+CONFIG_EPAPR_PARAVIRT                           policy<{'ppc64el': 'y'}>
+CONFIG_EPIC100                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EPOLL                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EQUALIZER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_EROFS_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_EROFS_FS_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_EROFS_FS_POSIX_ACL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EROFS_FS_SECURITY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EROFS_FS_XATTR                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EROFS_FS_ZIP                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ET131X                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ETHERNET                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ETHOC                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ETHTOOL_NETLINK                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EUROTECH_WDT                             policy<{'amd64': 'm'}>
+CONFIG_EVENTFD                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EVENT_TRACING                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EVM_ADD_XATTRS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EVM_EXTRA_SMACK_XATTRS                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXFAT_DEFAULT_IOCHARSET                  policy<{'amd64': '"utf8"', 'arm64': '"utf8"', 'armhf': '"utf8"', 'ppc64el': '"utf8"'}>
+CONFIG_EXFAT_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_EXPERT                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXPOLINE                                 policy<{'s390x': 'y'}>
+CONFIG_EXPOLINE_AUTO                            policy<{'s390x': 'y'}>
+CONFIG_EXPOLINE_EXTERN                          policy<{'s390x': 'y'}>
+CONFIG_EXPOLINE_FULL                            policy<{'s390x': 'n'}>
+CONFIG_EXPOLINE_OFF                             policy<{'s390x': 'n'}>
+CONFIG_EXPORTFS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXPORTFS_BLOCK_OPS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXT4_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_EXT4_FS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXT4_FS_POSIX_ACL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXT4_FS_SECURITY                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXT4_USE_FOR_EXT2                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_EXTCON                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_EXTCON_ADC_JACK                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_AXP288                            policy<{'amd64': 'm'}>
+CONFIG_EXTCON_FSA9480                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_GPIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_INTEL_CHT_WC                      policy<{'amd64': 'm'}>
+CONFIG_EXTCON_INTEL_INT3496                     policy<{'amd64': 'm'}>
+CONFIG_EXTCON_INTEL_MRFLD                       policy<{'amd64': 'm'}>
+CONFIG_EXTCON_MAX14577                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_MAX3355                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_MAX77693                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_MAX77843                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_MAX8997                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_PALMAS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_PTN5150                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_QCOM_SPMI_MISC                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EXTCON_RT8973A                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_SM5502                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_USBC_CROS_EC                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_EXTCON_USBC_TUSB320                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTCON_USB_GPIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EXTRA_FIRMWARE                           policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_EXTRA_TARGETS                            policy<{'ppc64el': '""'}>
+CONFIG_EXYNOS5422_DMC                           policy<{'armhf': 'm'}>
+CONFIG_EXYNOS_5250_COMMON_CLK                   policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_5260_COMMON_CLK                   policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_5410_COMMON_CLK                   policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_5420_COMMON_CLK                   policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_ADC                               policy<{'armhf': 'm'}>
+CONFIG_EXYNOS_ASV_ARM                           policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_AUDSS_CLK_CON                     policy<{'armhf': 'm'}>
+CONFIG_EXYNOS_CHIPID                            policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_CLKOUT                            policy<{'armhf': 'm'}>
+CONFIG_EXYNOS_CPU_SUSPEND                       policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_IOMMU                             policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_IOMMU_DEBUG                       policy<{'armhf': 'n'}>
+CONFIG_EXYNOS_IRQ_COMBINER                      policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_MCPM                              policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_PMU                               policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_PMU_ARM_DRIVERS                   policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_PM_DOMAINS                        policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_REGULATOR_COUPLER                 policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_SROM                              policy<{'armhf': 'y'}>
+CONFIG_EXYNOS_THERMAL                           policy<{'armhf': 'y'}>
+CONFIG_EZCHIP_NPS_MANAGEMENT_ENET               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_EZX_PCAP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_CHECK_FS                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_F2FS_FAULT_INJECTION                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_F2FS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_F2FS_FS_COMPRESSION                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_LZ4                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_LZ4HC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_LZO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_LZORLE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_POSIX_ACL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_SECURITY                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_XATTR                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_FS_ZSTD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F2FS_IOSTAT                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_F2FS_STAT_FS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_F71808E_WDT                              policy<{'amd64': 'm'}>
+CONFIG_FAILOVER                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FAIR_GROUP_SCHED                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FANOTIFY                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FANOTIFY_ACCESS_PERMISSIONS              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FARSYNC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FAT_DEFAULT_CODEPAGE                     policy<{'amd64': '437', 'arm64': '437', 'armhf': '437', 'ppc64el': '437', 's390x': '437'}>
+CONFIG_FAT_DEFAULT_IOCHARSET                    policy<{'amd64': '"iso8859-1"', 'arm64': '"iso8859-1"', 'armhf': '"iso8859-1"', 'ppc64el': '"iso8859-1"', 's390x': '"iso8859-1"'}>
+CONFIG_FAT_DEFAULT_UTF8                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FAT_FS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FAULT_INJECTION                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FB                                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FB_3DFX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_3DFX_ACCEL                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_3DFX_I2C                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_ARC                                   policy<{'amd64': 'm'}>
+CONFIG_FB_ARK                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_ARMCLCD                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_FB_ASILIANT                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FB_ATY                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_ATY128                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_ATY128_BACKLIGHT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_ATY_BACKLIGHT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_ATY_CT                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_ATY_GENERIC_LCD                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_ATY_GX                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_BACKLIGHT                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_BOOT_VESA_SUPPORT                     policy<{'amd64': 'y'}>
+CONFIG_FB_CARILLO_RANCH                         policy<{'amd64': 'm'}>
+CONFIG_FB_CARMINE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_CARMINE_DRAM_EVAL                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_CFB_COPYAREA                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_FB_CFB_FILLRECT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_FB_CFB_IMAGEBLIT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_FB_CFB_REV_PIXELS_IN_BYTE                policy<{'armhf-generic': 'y'}>
+CONFIG_FB_CIRRUS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_CMDLINE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FB_CYBER2000                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_CYBER2000_DDC                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_DA8XX                                 policy<{'armhf-generic': 'm'}>
+CONFIG_FB_DDC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_DEFERRED_IO                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FB_EFI                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_FB_FOREIGN_ENDIAN                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FB_HECUBA                                policy<{'amd64': 'm'}>
+CONFIG_FB_HGA                                   policy<{'amd64': 'm'}>
+CONFIG_FB_HYPERV                                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_FB_I740                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_IBM_GXT4500                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FB_IMSTT                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FB_IMX                                   policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_FB_INTEL                                 policy<{'amd64': 'm'}>
+CONFIG_FB_INTEL_DEBUG                           policy<{'amd64': 'n'}>
+CONFIG_FB_INTEL_I2C                             policy<{'amd64': 'y'}>
+CONFIG_FB_KYRO                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_LE80578                               policy<{'amd64': 'm'}>
+CONFIG_FB_MACMODES                              policy<{'ppc64el': 'y'}>
+CONFIG_FB_MATROX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_MATROX_G                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_MATROX_I2C                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_MATROX_MAVEN                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_MATROX_MILLENIUM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_MATROX_MYSTIQUE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_MB862XX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_MB862XX_I2C                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_MB862XX_LIME                          policy<{'ppc64el': 'n'}>
+CONFIG_FB_MB862XX_PCI_GDC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_METRONOME                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_MODE_HELPERS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FB_MX3                                   policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_FB_N411                                  policy<{'amd64': 'm'}>
+CONFIG_FB_NEOMAGIC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_NOTIFY                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FB_NVIDIA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_NVIDIA_BACKLIGHT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_NVIDIA_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_NVIDIA_I2C                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_OF                                    policy<{'ppc64el': 'y'}>
+CONFIG_FB_OMAP2                                 policy<{'armhf': 'm'}>
+CONFIG_FB_OMAP2_CONNECTOR_ANALOG_TV             policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_CONNECTOR_DVI                   policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_CONNECTOR_HDMI                  policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_DEBUG_SUPPORT                   policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_DSS                             policy<{'armhf': 'm'}>
+CONFIG_FB_OMAP2_DSS_DEBUG                       policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_DSS_DEBUGFS                     policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_DSS_DPI                         policy<{'armhf': 'y'}>
+CONFIG_FB_OMAP2_DSS_DSI                         policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_DSS_HDMI_COMMON                 policy<{'armhf': 'y'}>
+CONFIG_FB_OMAP2_DSS_INIT                        policy<{'armhf': 'y'}>
+CONFIG_FB_OMAP2_DSS_MIN_FCK_PER_PCK             policy<{'armhf': '0'}>
+CONFIG_FB_OMAP2_DSS_SDI                         policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_DSS_SLEEP_AFTER_VENC_RESET      policy<{'armhf': 'y'}>
+CONFIG_FB_OMAP2_DSS_VENC                        policy<{'armhf': 'y'}>
+CONFIG_FB_OMAP2_ENCODER_OPA362                  policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_ENCODER_TFP410                  policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_ENCODER_TPD12S015               policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_NUM_FBS                         policy<{'armhf': '3'}>
+CONFIG_FB_OMAP2_PANEL_DPI                       policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP2_PANEL_LGPHILIPS_LB035Q02        policy<{'armhf': 'n'}>
+CONFIG_FB_OMAP4_DSS_HDMI                        policy<{'armhf': 'y'}>
+CONFIG_FB_OMAP5_DSS_HDMI                        policy<{'armhf': 'n'}>
+CONFIG_FB_OPENCORES                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_PM2                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_PM2_FIFO_DISCONNECT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_PM3                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_PROVIDE_GET_FB_UNMAPPED_AREA          policy<{'armhf': 'y'}>
+CONFIG_FB_RADEON                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_RADEON_BACKLIGHT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_RADEON_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_RADEON_I2C                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_RIVA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_RIVA_BACKLIGHT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_RIVA_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_RIVA_I2C                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_S1D13XXX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_S3                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_S3_DDC                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_SAVAGE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_SAVAGE_ACCEL                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FB_SAVAGE_I2C                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_SH_MOBILE_LCDC                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_FB_SIMPLE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_SIS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_SIS_300                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_SIS_315                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FB_SM501                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_SM712                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_SM750                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_SMSCUFX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_SSD1307                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_SVGALIB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_SYS_COPYAREA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FB_SYS_FILLRECT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FB_SYS_FOPS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FB_SYS_IMAGEBLIT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FB_TFT                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_AGM1264K_FL                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_BD663474                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_HX8340BN                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_HX8347D                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_HX8353D                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_HX8357D                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9163                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9320                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9325                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9340                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9341                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9481                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ILI9486                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_PCD8544                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_RA8875                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_S6D02A1                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_S6D1121                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SEPS525                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SH1106                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SSD1289                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SSD1305                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SSD1306                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SSD1331                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_SSD1351                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ST7735R                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_ST7789V                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_TINYLCD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_TLS8204                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_UC1611                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_UC1701                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_UPD161704                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TFT_WATTEROTT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_TILEBLITTING                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FB_TMIO                                  policy<{'armhf': 'm'}>
+CONFIG_FB_TMIO_ACCELL                           policy<{'armhf': 'y'}>
+CONFIG_FB_TRIDENT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_UDL                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_UVESA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_VESA                                  policy<{'amd64': 'y'}>
+CONFIG_FB_VGA16                                 policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_FB_VIA                                   policy<{'amd64': 'm'}>
+CONFIG_FB_VIA_DIRECT_PROCFS                     policy<{'amd64': 'n'}>
+CONFIG_FB_VIA_X_COMPATIBILITY                   policy<{'amd64': 'y'}>
+CONFIG_FB_VIRTUAL                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FB_VOODOO1                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_VT8623                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FB_XILINX                                policy<{'arm64': 'm'}>
+CONFIG_FCOE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FCOE_FNIC                                policy<{'amd64': 'm'}>
+CONFIG_FDDI                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FEALNX                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FEC                                      policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_FHCI_DEBUG                               policy<{'ppc64el': 'n'}>
+CONFIG_FIB_RULES                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FIELDBUS_DEV                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FILE_LOCKING                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FIND_BIT_BENCHMARK                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FIQ                                      policy<{'armhf-generic': 'y'}>
+CONFIG_FIREWIRE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FIREWIRE_NET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FIREWIRE_NOSY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FIREWIRE_OHCI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FIREWIRE_SBP2                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FIREWIRE_SERIAL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FIRMWARE_EDID                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FIRMWARE_MEMMAP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FIXED_PHY                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_FIX_EARLYCON_MEM                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_FLATMEM_MANUAL                           policy<{'armhf': 'n'}>
+CONFIG_FM10K                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FONTS                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FONT_10x18                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_6x10                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FONT_6x11                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_6x8                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_7x14                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_8x16                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FONT_8x8                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FONT_ACORN_8x8                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FONT_MINI_4x6                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_PEARL_8x8                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_SUN12x22                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_SUN8x16                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FONT_SUPPORT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FONT_TER16x32                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FORCEDETH                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FORCE_MAX_ZONEORDER                      policy<{'arm64-generic': '13', 'arm64-generic-64k': '14', 'arm64-lowlatency': '13', 'arm64-lowlatency-64k': '14', 'armhf-generic': '12', 'armhf-generic-lpae': '11', 'ppc64el': '9'}>
+CONFIG_FORCE_PCI                                policy<{'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FORCE_SMP                                policy<{'ppc64el': 'y'}>
+CONFIG_FORTIFY_SOURCE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FPGA                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FPGA_BRIDGE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FPGA_DFL                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_FPGA_DFL_AFU                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_EMIF                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_FME                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_FME_BRIDGE                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_FME_MGR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_FME_REGION                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_NIOS_INTEL_PAC_N3000            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_DFL_PCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_MGR_ALTERA_CVP                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FPGA_MGR_ALTERA_PS_SPI                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_MGR_ICE40_SPI                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_MGR_MACHXO2_SPI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_MGR_SOCFPGA                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_FPGA_MGR_SOCFPGA_A10                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_FPGA_MGR_STRATIX10_SOC                   policy<{'arm64': 'm'}>
+CONFIG_FPGA_MGR_VERSAL_FPGA                     policy<{'arm64': 'm'}>
+CONFIG_FPGA_MGR_XILINX_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FPGA_MGR_ZYNQMP_FPGA                     policy<{'arm64': 'm'}>
+CONFIG_FPGA_REGION                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FRAMEBUFFER_CONSOLE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FRAME_POINTER                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_FRAME_WARN                               policy<{'amd64': '1024', 'arm64': '1024', 'armhf': '1024', 'ppc64el': '2048', 's390x': '1024'}>
+CONFIG_FREEZER                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FRONTSWAP                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FSCACHE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_FSCACHE_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FSCACHE_STATS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FSI                                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSI_MASTER_ASPEED                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSI_MASTER_AST_CF                        policy<{'armhf': 'm'}>
+CONFIG_FSI_MASTER_GPIO                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSI_MASTER_HUB                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSI_NEW_DEV_NODE                         policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_FSI_OCC                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSI_SBEFIFO                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSI_SCOM                                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_BMAN_TEST                            policy<{'arm64': 'm'}>
+CONFIG_FSL_BMAN_TEST_API                        policy<{'arm64': 'n'}>
+CONFIG_FSL_DPAA                                 policy<{'arm64': 'y'}>
+CONFIG_FSL_DPAA2_ETH                            policy<{'arm64': 'm'}>
+CONFIG_FSL_DPAA2_ETH_DCB                        policy<{'arm64': 'y'}>
+CONFIG_FSL_DPAA2_PTP_CLOCK                      policy<{'arm64': 'm'}>
+CONFIG_FSL_DPAA2_QDMA                           policy<{'arm64': 'm'}>
+CONFIG_FSL_DPAA2_SWITCH                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_DPAA_CHECKING                        policy<{'arm64': 'y'}>
+CONFIG_FSL_DPAA_ETH                             policy<{'arm64': 'm'}>
+CONFIG_FSL_EDMA                                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_ENETC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_ENETC_IERB                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_ENETC_MDIO                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_ENETC_PTP_CLOCK                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_ENETC_QOS                            policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FSL_ENETC_VF                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_ERRATUM_A008585                      policy<{'arm64': 'y'}>
+CONFIG_FSL_FMAN                                 policy<{'arm64': 'y'}>
+CONFIG_FSL_GTM                                  policy<{'ppc64el': 'y'}>
+CONFIG_FSL_GUTS                                 policy<{'arm64': 'y', 'armhf-generic': 'y', 'ppc64el': 'y'}>
+CONFIG_FSL_IFC                                  policy<{'arm64': 'y'}>
+CONFIG_FSL_IMX8_DDR_PMU                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_FSL_LBC                                  policy<{'ppc64el': 'y'}>
+CONFIG_FSL_MC_BUS                               policy<{'arm64': 'y', 'armhf-generic': 'n'}>
+CONFIG_FSL_MC_DPIO                              policy<{'arm64': 'm'}>
+CONFIG_FSL_MC_UAPI_SUPPORT                      policy<{'arm64': 'y'}>
+CONFIG_FSL_PQ_MDIO                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_QDMA                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_FSL_QMAN_TEST                            policy<{'arm64': 'n'}>
+CONFIG_FSL_RCPM                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_FSL_UCC_HDLC                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FSL_XGMAC_MDIO                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FSNOTIFY                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_DAX                                   policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_DAX_LIMITED                           policy<{'s390x': 'y'}>
+CONFIG_FS_DAX_PMD                               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_FS_ENCRYPTION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_ENCRYPTION_ALGS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_ENCRYPTION_INLINE_CRYPT               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_IOMAP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_MBCACHE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_POSIX_ACL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_VERITY                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_VERITY_BUILTIN_SIGNATURES             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FS_VERITY_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FTGMAC100                                policy<{'armhf': 'm'}>
+CONFIG_FTL                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FTMAC100                                 policy<{'armhf': 'm'}>
+CONFIG_FTM_QUADDEC                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FTRACE                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FTRACE_MCOUNT_RECORD                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FTRACE_MCOUNT_USE_CC                     policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY policy<{'arm64': 'y'}>
+CONFIG_FTRACE_MCOUNT_USE_RECORDMCOUNT           policy<{'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FTRACE_RECORD_RECURSION                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FTRACE_STARTUP_TEST                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_FTRACE_SYSCALLS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FTR_FIXUP_SELFTEST                       policy<{'ppc64el': 'n'}>
+CONFIG_FTWDT010_WATCHDOG                        policy<{'armhf': 'm'}>
+CONFIG_FUEL_GAUGE_SC27XX                        policy<{'arm64': 'm'}>
+CONFIG_FUJITSU_ERRATUM_010001                   policy<{'arm64': 'y'}>
+CONFIG_FUJITSU_ES                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_FUJITSU_LAPTOP                           policy<{'amd64': 'm'}>
+CONFIG_FUJITSU_TABLET                           policy<{'amd64': 'm'}>
+CONFIG_FUNCTION_ALIGNMENT                       policy<{'amd64': '16', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_FUNCTION_ALIGNMENT_16B                   policy<{'amd64': 'y'}>
+CONFIG_FUNCTION_ALIGNMENT_4B                    policy<{'amd64': 'y'}>
+CONFIG_FUNCTION_ERROR_INJECTION                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUNCTION_GRAPH_TRACER                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUNCTION_PROFILER                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUNCTION_TRACER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUSE_DAX                                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUSION                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_FUSION_CTL                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FUSION_FC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FUSION_LAN                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FUSION_LOGGING                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FUSION_MAX_SGE                           policy<{'amd64': '128', 'arm64': '128', 'armhf': '128', 'ppc64el': '128'}>
+CONFIG_FUSION_SAS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FUSION_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FUTEX                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FUTEX_PI                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FWNODE_MDIO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FWTTY_MAX_CARD_PORTS                     policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32'}>
+CONFIG_FWTTY_MAX_TOTAL_PORTS                    policy<{'amd64': '64', 'arm64': '64', 'armhf': '64', 'ppc64el': '64'}>
+CONFIG_FW_ATTR_CLASS                            policy<{'amd64': 'm'}>
+CONFIG_FW_CACHE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_FW_CFG_SYSFS                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_FW_CFG_SYSFS_CMDLINE                     policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_FW_LOADER                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FW_LOADER_COMPRESS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FW_LOADER_COMPRESS_XZ                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FW_LOADER_PAGED_BUF                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FW_LOADER_USER_HELPER                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_FXAS21002C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXAS21002C_I2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXAS21002C_SPI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXLS8962AF                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXLS8962AF_I2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXLS8962AF_SPI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXOS8700                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXOS8700_I2C                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_FXOS8700_SPI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GACT_PROB                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GADGET_UAC1                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GADGET_UAC1_LEGACY                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_GAMEPORT                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GAMEPORT_EMU10K1                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GAMEPORT_FM801                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GAMEPORT_L4                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GAMEPORT_NS558                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GARP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GART_IOMMU                               policy<{'amd64': 'y'}>
+CONFIG_GCC_VERSION                              policy<{'amd64': '110400', 'arm64': '110400', 'armhf': '110400', 'ppc64el': '110400', 's390x': '110400'}>
+CONFIG_GCOV_KERNEL                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GDB_SCRIPTS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GDS_FORCE_MITIGATION                     policy<{'amd64': 'n'}>
+CONFIG_GEMINI_ETHERNET                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GENERIC_ADC_BATTERY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GENERIC_ADC_THERMAL                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GENERIC_ALLOCATOR                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_ARCH_NUMA                        policy<{'arm64': 'y'}>
+CONFIG_GENERIC_ARCH_TOPOLOGY                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_BUG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_BUG_RELATIVE_POINTERS            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_CALIBRATE_DELAY                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_CLOCKEVENTS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_CLOCKEVENTS_MIN_ADJUST           policy<{'amd64': 'y'}>
+CONFIG_GENERIC_CMOS_UPDATE                      policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_CPU                              policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_CPU_AUTOPROBE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_CPU_VULNERABILITIES              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_CSUM                             policy<{'arm64': 'y'}>
+CONFIG_GENERIC_EARLY_IOREMAP                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_ENTRY                            policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_FIND_FIRST_BIT                   policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_GETTIMEOFDAY                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_HWEIGHT                          policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_IDLE_POLL_SETUP                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_IOMAP                            policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_IRQ_CHIP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_IRQ_DEBUGFS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_IRQ_IPI                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_IRQ_MATRIX_ALLOCATOR             policy<{'amd64': 'y'}>
+CONFIG_GENERIC_IRQ_MIGRATION                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_IRQ_MULTI_HANDLER                policy<{'armhf': 'y'}>
+CONFIG_GENERIC_IRQ_PROBE                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_IRQ_RESERVATION_MODE             policy<{'amd64': 'y'}>
+CONFIG_GENERIC_IRQ_SHOW                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_IRQ_SHOW_LEVEL                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_ISA_DMA                          policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_MSI_IRQ                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_MSI_IRQ_DOMAIN                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_NET_UTILS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_PCI_IOMAP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_PENDING_IRQ                      policy<{'amd64': 'y'}>
+CONFIG_GENERIC_PHY                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_GENERIC_PHY_MIPI_DPHY                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_PINCONF                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_PINCTRL_GROUPS                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_PINMUX_FUNCTIONS                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GENERIC_PTDUMP                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_SCHED_CLOCK                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GENERIC_SMP_IDLE_THREAD                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_STRNCPY_FROM_USER                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_STRNLEN_USER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_TIME_VSYSCALL                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_TRACER                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENERIC_VDSO_32                          policy<{'armhf': 'y'}>
+CONFIG_GENERIC_VDSO_TIME_NS                     policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GENEVE                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GENWQE                                   policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GENWQE_PLATFORM_ERROR_RECOVERY           policy<{'amd64': '0', 'arm64': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_GEN_RTC                                  policy<{'ppc64el': 'y'}>
+CONFIG_GFS2_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GFS2_FS_LOCKING_DLM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GIANFAR                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GIGABYTE_WMI                             policy<{'amd64': 'm'}>
+CONFIG_GLOB                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GLOB_SELFTEST                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GNSS                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GNSS_MTK_SERIAL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GNSS_SERIAL                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GNSS_SIRF_SERIAL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GNSS_UBX_SERIAL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GOLDFISH                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GOOGLE_FIRMWARE                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GP2AP002                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GP2AP020A00F                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPD_POCKET_FAN                           policy<{'amd64': 'm'}>
+CONFIG_GPIOLIB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GPIOLIB_FASTPATH_LIMIT                   policy<{'amd64': '512', 'arm64': '512', 'armhf': '512', 'ppc64el': '512', 's390x': '512'}>
+CONFIG_GPIOLIB_IRQCHIP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GPIO_104_DIO_48E                         policy<{'amd64': 'm'}>
+CONFIG_GPIO_104_IDIO_16                         policy<{'amd64': 'm'}>
+CONFIG_GPIO_104_IDI_48                          policy<{'amd64': 'm'}>
+CONFIG_GPIO_74X164                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_74XX_MMIO                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_AAEON                               policy<{'amd64': 'm'}>
+CONFIG_GPIO_ACPI                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_GPIO_ADNP                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_ADP5520                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_ADP5588                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_AGGREGATOR                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GPIO_ALTERA                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_ALTERA_A10SR                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_GPIO_AMD8111                             policy<{'amd64': 'm'}>
+CONFIG_GPIO_AMDPT                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_GPIO_AMD_FCH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_ARIZONA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_ASPEED                              policy<{'armhf': 'm'}>
+CONFIG_GPIO_ASPEED_SGPIO                        policy<{'armhf': 'y'}>
+CONFIG_GPIO_BCM_XGS_IPROC                       policy<{'arm64': 'm'}>
+CONFIG_GPIO_BD70528                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_BD71815                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_BD71828                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_BD9571MWV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_BRCMSTB                             policy<{'arm64': 'm'}>
+CONFIG_GPIO_BT8XX                               policy<{'s390x': 'm'}>
+CONFIG_GPIO_CADENCE                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_CDEV                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GPIO_CRYSTAL_COVE                        policy<{'amd64': 'y'}>
+CONFIG_GPIO_DA9052                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_DA9055                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_DAVINCI                             policy<{'arm64': 'y'}>
+CONFIG_GPIO_DLN2                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_DWAPB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_EIC_SPRD                            policy<{'arm64': 'm'}>
+CONFIG_GPIO_EXAR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_F7188X                              policy<{'amd64': 'm'}>
+CONFIG_GPIO_FTGPIO010                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_GENERIC                             policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_GPIO_GENERIC_PLATFORM                    policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GPIO_GPIO_MM                             policy<{'amd64': 'm'}>
+CONFIG_GPIO_GRGPIO                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_GW_PLD                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_HISI                                policy<{'arm64': 'm'}>
+CONFIG_GPIO_HLWD                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_ICH                                 policy<{'amd64': 'm'}>
+CONFIG_GPIO_IT87                                policy<{'amd64': 'm'}>
+CONFIG_GPIO_JANZ_TTL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_KEMPLD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_LJCA                                policy<{'amd64': 'm'}>
+CONFIG_GPIO_LOGICVC                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_LP3943                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_LP873X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_LP87565                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_M058SSAN                            policy<{'amd64': 'm'}>
+CONFIG_GPIO_MADERA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MAX3191X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MAX7300                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_MAX7301                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MAX730X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MAX732X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_MAX77620                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MAX77650                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MB86S7X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_MC33880                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MENZ127                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MLXBF                               policy<{'arm64': 'm'}>
+CONFIG_GPIO_MLXBF2                              policy<{'arm64': 'm'}>
+CONFIG_GPIO_ML_IOH                              policy<{'amd64': 'm'}>
+CONFIG_GPIO_MOCKUP                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GPIO_MOXTET                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_MPC8XXX                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GPIO_MSC313                              policy<{'armhf': 'y'}>
+CONFIG_GPIO_MVEBU                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GPIO_MXC                                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_GPIO_OMAP                                policy<{'armhf': 'y'}>
+CONFIG_GPIO_PALMAS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_PCA953X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_PCA953X_IRQ                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_PCA9570                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_PCF857X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_PCIE_IDIO_24                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GPIO_PCI_IDIO_16                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GPIO_PISOSR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_PL061                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_GPIO_PMIC_EIC_SPRD                       policy<{'arm64': 'm'}>
+CONFIG_GPIO_RASPBERRYPI_EXP                     policy<{'arm64': 'm'}>
+CONFIG_GPIO_RC5T583                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_RCAR                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_GPIO_RDA                                 policy<{'armhf': 'y'}>
+CONFIG_GPIO_RDC321X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_REGMAP                              policy<{'arm64': 'm'}>
+CONFIG_GPIO_ROCKCHIP                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_GPIO_SAMA5D2_PIOBU                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_SCH                                 policy<{'amd64': 'm'}>
+CONFIG_GPIO_SCH311X                             policy<{'amd64': 'm'}>
+CONFIG_GPIO_SIFIVE                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_SIOX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_SL28CPLD                            policy<{'arm64': 'm'}>
+CONFIG_GPIO_SPRD                                policy<{'arm64': 'm'}>
+CONFIG_GPIO_STMPE                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_SYSCON                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_SYSFS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GPIO_TC3589X                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_TEGRA                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_GPIO_TEGRA186                            policy<{'arm64': 'y'}>
+CONFIG_GPIO_THUNDERX                            policy<{'arm64': 'm'}>
+CONFIG_GPIO_TPIC2810                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_TPS65086                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_TPS65218                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_TPS6586X                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_TPS65910                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_TPS65912                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_TPS68470                            policy<{'amd64': 'y'}>
+CONFIG_GPIO_TQMX86                              policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_TS4800                              policy<{'armhf-generic': 'm'}>
+CONFIG_GPIO_TS4900                              policy<{'armhf-generic': 'm'}>
+CONFIG_GPIO_TWL6040                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_GPIO_UCB1400                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_UNIPHIER                            policy<{'armhf': 'm'}>
+CONFIG_GPIO_VF610                               policy<{'armhf-generic': 'y'}>
+CONFIG_GPIO_VIPERBOARD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_VIRTIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GPIO_VISCONTI                            policy<{'arm64': 'm'}>
+CONFIG_GPIO_VX855                               policy<{'amd64': 'm'}>
+CONFIG_GPIO_WATCHDOG                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_WCD934X                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_WHISKEY_COVE                        policy<{'amd64': 'm'}>
+CONFIG_GPIO_WINBOND                             policy<{'amd64': 'm'}>
+CONFIG_GPIO_WM831X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_WM8350                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_WM8994                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_WS16C48                             policy<{'amd64': 'm'}>
+CONFIG_GPIO_XGENE                               policy<{'arm64': 'y'}>
+CONFIG_GPIO_XGENE_SB                            policy<{'arm64': 'm'}>
+CONFIG_GPIO_XILINX                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GPIO_XLP                                 policy<{'arm64': 'm'}>
+CONFIG_GPIO_XRA1403                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GPIO_ZEVIO                               policy<{'armhf': 'y'}>
+CONFIG_GPIO_ZYNQ                                policy<{'arm64': 'm'}>
+CONFIG_GRACE_PERIOD                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GREENASIA_FF                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_GREYBUS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_GREYBUS_AUDIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_AUDIO_APB_CODEC                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_BOOTROM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_BRIDGED_PHY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_ES2                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_FIRMWARE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_GPIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_HID                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_LIGHT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_LOG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_LOOPBACK                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_POWER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_PWM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_RAW                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_SDIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_UART                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_USB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GREYBUS_VIBRATOR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GRO_CELLS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_GS_FPGABOOT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_GTP                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_GUP_TEST                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_GVE                                      policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_HABANA_AI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HALTPOLL_CPUIDLE                         policy<{'amd64': 'm'}>
+CONFIG_HAMACHI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HAMRADIO                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HANDLE_DOMAIN_IRQ                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HANGCHECK_TIMER                          policy<{'amd64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_HAPPYMEAL                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HARDENED_USERCOPY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HARDENED_USERCOPY_FALLBACK               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HARDENED_USERCOPY_PAGESPAN               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HARDEN_BRANCH_HISTORY                    policy<{'armhf': 'y'}>
+CONFIG_HARDEN_BRANCH_PREDICTOR                  policy<{'armhf': 'y'}>
+CONFIG_HARDIRQS_SW_RESEND                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HARDLOCKUP_CHECK_TIMESTAMP               policy<{'amd64': 'y'}>
+CONFIG_HARDLOCKUP_DETECTOR                      policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_HARDLOCKUP_DETECTOR_PERF                 policy<{'amd64': 'y'}>
+CONFIG_HAS_DMA                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAS_IOMEM                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAS_IOPORT_MAP                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_ACPI_APEI                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HAVE_ACPI_APEI_NMI                       policy<{'amd64': 'y'}>
+CONFIG_HAVE_ALIGNED_STRUCT_PAGE                 policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_AUDITSYSCALL                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_BITREVERSE                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HAVE_ARCH_COMPAT_MMAP_BASES              policy<{'amd64': 'y'}>
+CONFIG_HAVE_ARCH_COMPILER_H                     policy<{'arm64': 'y'}>
+CONFIG_HAVE_ARCH_HUGE_VMALLOC                   policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_ARCH_HUGE_VMAP                      policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_ARCH_JUMP_LABEL                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_JUMP_LABEL_RELATIVE            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_KASAN                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_KASAN_HW_TAGS                  policy<{'arm64': 'y'}>
+CONFIG_HAVE_ARCH_KASAN_SW_TAGS                  policy<{'arm64': 'y'}>
+CONFIG_HAVE_ARCH_KASAN_VMALLOC                  policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_KCSAN                          policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_KFENCE                         policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_KGDB                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_ARCH_MMAP_RND_BITS                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_ARCH_MMAP_RND_COMPAT_BITS           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_ARCH_NVRAM_OPS                      policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_ARCH_PFN_VALID                      policy<{'armhf': 'y'}>
+CONFIG_HAVE_ARCH_PREL32_RELOCATIONS             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET        policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_SECCOMP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_SECCOMP_FILTER                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_SOFT_DIRTY                     policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_STACKLEAK                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HAVE_ARCH_TRACEHOOK                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE           policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD       policy<{'amd64': 'y'}>
+CONFIG_HAVE_ARCH_USERFAULTFD_MINOR              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HAVE_ARCH_USERFAULTFD_WP                 policy<{'amd64': 'y'}>
+CONFIG_HAVE_ARCH_VMAP_STACK                     policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_ARCH_WITHIN_STACK_FRAMES            policy<{'amd64': 'y'}>
+CONFIG_HAVE_ARM_ARCH_TIMER                      policy<{'armhf': 'y'}>
+CONFIG_HAVE_ARM_SCU                             policy<{'armhf': 'y'}>
+CONFIG_HAVE_ARM_SMCCC                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HAVE_ARM_SMCCC_DISCOVERY                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HAVE_ARM_TWD                             policy<{'armhf': 'y'}>
+CONFIG_HAVE_ASM_MODVERSIONS                     policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_BOOTMEM_INFO_NODE                   policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_CLK                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_CLK_PREPARE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_CMPXCHG_DOUBLE                      policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_CMPXCHG_LOCAL                       policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_CONTEXT_TRACKING                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_CONTEXT_TRACKING_OFFSTACK           policy<{'amd64': 'y'}>
+CONFIG_HAVE_C_RECORDMCOUNT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_DEBUG_KMEMLEAK                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_DEBUG_STACKOVERFLOW                 policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_DMA_CONTIGUOUS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_DYNAMIC_FTRACE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_ARGS            policy<{'amd64': 'y'}>
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_DIRECT_CALLS    policy<{'amd64': 'y'}>
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_EBPF_JIT                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_EXIT_THREAD                         policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_HAVE_FAST_GUP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_FENTRY                              policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_FUNCTION_ARG_ACCESS_API             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HAVE_FUNCTION_ERROR_INJECTION            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_FUNCTION_TRACER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_FUTEX_CMPXCHG                       policy<{'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_GCC_PLUGINS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_GENERIC_VDSO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_HARDENED_USERCOPY_ALLOCATOR         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_HARDLOCKUP_DETECTOR_ARCH            policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_HARDLOCKUP_DETECTOR_PERF            policy<{'amd64': 'y'}>
+CONFIG_HAVE_HW_BREAKPOINT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_IMA_KEXEC                           policy<{'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_IMX_ANATOP                          policy<{'armhf-generic': 'y'}>
+CONFIG_HAVE_IMX_GPC                             policy<{'armhf-generic': 'y'}>
+CONFIG_HAVE_IMX_MMDC                            policy<{'armhf-generic': 'y'}>
+CONFIG_HAVE_IMX_SRC                             policy<{'armhf-generic': 'y'}>
+CONFIG_HAVE_INTEL_TXT                           policy<{'amd64': 'y'}>
+CONFIG_HAVE_IOREMAP_PROT                        policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK               policy<{'amd64': 'y'}>
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_KCSAN_COMPILER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_BZIP2                        policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_GZIP                         policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_LZ4                          policy<{'amd64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_LZMA                         policy<{'amd64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_LZO                          policy<{'amd64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_UNCOMPRESSED                 policy<{'s390x': 'y'}>
+CONFIG_HAVE_KERNEL_XZ                           policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KERNEL_ZSTD                         policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KPROBES                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KPROBES_ON_FTRACE                   policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KRETPROBES                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM                                 policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_ARCH_TLB_FLUSH_ALL              policy<{'arm64': 'y'}>
+CONFIG_HAVE_KVM_CPU_RELAX_INTERCEPT             policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_EVENTFD                         policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_INVALID_WAKEUPS                 policy<{'s390x': 'y'}>
+CONFIG_HAVE_KVM_IRQCHIP                         policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_IRQFD                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_IRQ_BYPASS                      policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_KVM_IRQ_ROUTING                     policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_MSI                             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HAVE_KVM_NO_POLL                         policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_PM_NOTIFIER                     policy<{'amd64': 'y'}>
+CONFIG_HAVE_KVM_VCPU_ASYNC_IOCTL                policy<{'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_KVM_VCPU_RUN_PID_CHANGE             policy<{'arm64': 'y'}>
+CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION       policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_LIVEPATCH                           policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_MARCH_Z10_FEATURES                  policy<{'s390x': 'y'}>
+CONFIG_HAVE_MARCH_Z13_FEATURES                  policy<{'s390x': 'y'}>
+CONFIG_HAVE_MARCH_Z196_FEATURES                 policy<{'s390x': 'y'}>
+CONFIG_HAVE_MARCH_Z900_FEATURES                 policy<{'s390x': 'y'}>
+CONFIG_HAVE_MARCH_Z990_FEATURES                 policy<{'s390x': 'y'}>
+CONFIG_HAVE_MARCH_Z9_109_FEATURES               policy<{'s390x': 'y'}>
+CONFIG_HAVE_MARCH_ZEC12_FEATURES                policy<{'s390x': 'y'}>
+CONFIG_HAVE_MEMBLOCK_PHYS_MAP                   policy<{'s390x': 'y'}>
+CONFIG_HAVE_MEMORYLESS_NODES                    policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_MIXED_BREAKPOINTS_REGS              policy<{'amd64': 'y'}>
+CONFIG_HAVE_MMIOTRACE_SUPPORT                   policy<{'amd64': 'y'}>
+CONFIG_HAVE_MOD_ARCH_SPECIFIC                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_MOVE_PMD                            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_MOVE_PUD                            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_NMI                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_NMI_WATCHDOG                        policy<{'ppc64el': 'y'}>
+CONFIG_HAVE_NOP_MCOUNT                          policy<{'s390x': 'y'}>
+CONFIG_HAVE_OBJTOOL_MCOUNT                      policy<{'amd64': 'y'}>
+CONFIG_HAVE_OPTPROBES                           policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_PATA_PLATFORM                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HAVE_PCI                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_PCSPKR_PLATFORM                     policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_PERF_EVENTS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_PERF_EVENTS_NMI                     policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_PERF_REGS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_PERF_USER_STACK_DUMP                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_PNETID                              policy<{'s390x': 'm'}>
+CONFIG_HAVE_POSIX_CPU_TIMERS_TASK_WORK          policy<{'amd64': 'y'}>
+CONFIG_HAVE_PREEMPT_DYNAMIC                     policy<{'amd64': 'y'}>
+CONFIG_HAVE_PROC_CPU                            policy<{'armhf': 'y'}>
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_RELIABLE_STACKTRACE                 policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_RSEQ                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_S3C2410_I2C                         policy<{'armhf': 'y'}>
+CONFIG_HAVE_S3C_RTC                             policy<{'armhf': 'y'}>
+CONFIG_HAVE_SETUP_PER_CPU_AREA                  policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_SMP                                 policy<{'armhf': 'y'}>
+CONFIG_HAVE_SOFTIRQ_ON_OWN_STACK                policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_STACKPROTECTOR                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HAVE_STACK_VALIDATION                    policy<{'amd64': 'y'}>
+CONFIG_HAVE_STATIC_CALL                         policy<{'amd64': 'y'}>
+CONFIG_HAVE_STATIC_CALL_INLINE                  policy<{'amd64': 'y'}>
+CONFIG_HAVE_SYSCALL_TRACEPOINTS                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_UID16                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_HAVE_UNSTABLE_SCHED_CLOCK                policy<{'amd64': 'y'}>
+CONFIG_HAVE_USER_RETURN_NOTIFIER                policy<{'amd64': 'y'}>
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING                 policy<{'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_IDLE            policy<{'s390x': 'y'}>
+CONFIG_HBMC_AM654                               policy<{'arm64': 'm'}>
+CONFIG_HCALL_STATS                              policy<{'ppc64el': 'n'}>
+CONFIG_HD44780                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HD44780_COMMON                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDC100X                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDC2010                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC_CISCO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC_FR                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC_PPP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC_RAW                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC_RAW_ETH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDLC_X25                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HDMI                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HDMI_LPE_AUDIO                           policy<{'amd64': 'm'}>
+CONFIG_HDQ_MASTER_OMAP                          policy<{'armhf': 'm'}>
+CONFIG_HEADERS_INSTALL                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HERMES                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HERMES_CACHE_FW_ON_INIT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HERMES_PRISM                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_HFI1_DEBUG_SDMA_ORDER                    policy<{'amd64': 'n'}>
+CONFIG_HFSPLUS_FS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HI13X1_GMAC                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HI3660_MBOX                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HI6220_MBOX                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HI6421V600_IRQ                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HI8435                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HIBERNATE_CALLBACKS                      policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_HIBERNATION_SNAPSHOT_DEV                 policy<{'amd64': 'y', 'armhf': 'y'}>
+CONFIG_HID                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HIDRAW                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_A4TECH                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ACCUTOUCH                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ACRUX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ACRUX_FF                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_ALPS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_APPLE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_APPLEIR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ASUS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_AUREAL                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_BATTERY_STRENGTH                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_BELKIN                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_BETOP_FF                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_BIGBEN_FF                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CHERRY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CHICONY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CMEDIA                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CORSAIR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_COUGAR                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CP2112                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CREATIVE_SB0540                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_CYPRESS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_DRAGONRISE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ELAN                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ELECOM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ELO                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_EMS_FF                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_EZKEY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_FT260                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GEMBIRD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GENERIC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GFRM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GLORIOUS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GOOGLE_HAMMER                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HID_GREENASIA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GT683R                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_GYRATION                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_HOLTEK                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_HYPERV_MOUSE                         policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HID_ICADE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ITE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_JABRA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_KENSINGTON                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_KEYTOUCH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_KYE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_LCPOWER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_LED                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_LENOVO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_LOGITECH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_LOGITECH_DJ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_LOGITECH_HIDPP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MACALLY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MAGICMOUSE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MALTRON                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MAYFLASH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MCP2221                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MICROSOFT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MONTEREY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_MULTITOUCH                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_NTI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_NTRIG                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ORTEK                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PANTHERLORD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PENMOUNT                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PETALYNX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PICOLCD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PICOLCD_BACKLIGHT                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_PICOLCD_CIR                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_PICOLCD_FB                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_PICOLCD_LCD                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_PICOLCD_LEDS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_PID                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HID_PLANTRONICS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PLAYSTATION                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PRIMAX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_PRODIKEYS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_REDRAGON                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_RETRODE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_RMI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ROCCAT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SAITEK                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SAMSUNG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SEMITEK                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_ACCEL_3D                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_ALS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_CUSTOM_INTEL_HINGE            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_CUSTOM_SENSOR                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_DEVICE_ROTATION               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_GYRO_3D                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_HUB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_HUMIDITY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_IIO_COMMON                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_IIO_TRIGGER                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_INCLINOMETER_3D               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_MAGNETOMETER_3D               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_PRESS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_PROX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SENSOR_TEMP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SMARTJOYPLUS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SONY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SPEEDLINK                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_STEAM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_STEELSERIES                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_SUNPLUS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_THINGM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_THRUSTMASTER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_TIVO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_TOPSEED                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_TWINHAN                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_U2FZERO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_UCLOGIC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_UDRAW_PS3                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_VIEWSONIC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_VIVALDI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_WACOM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_WALTOP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_WIIMOTE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_XINMO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ZEROPLUS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HID_ZYDACRON                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HIGHMEM                                  policy<{'armhf': 'y'}>
+CONFIG_HIGHPTE                                  policy<{'armhf': 'y'}>
+CONFIG_HIGH_RES_TIMERS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HINIC                                    policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HIP04_ETH                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HISILICON_ERRATUM_161010101              policy<{'arm64': 'y'}>
+CONFIG_HISILICON_ERRATUM_161600802              policy<{'arm64': 'y'}>
+CONFIG_HISILICON_IRQ_MBIGEN                     policy<{'arm64': 'y'}>
+CONFIG_HISILICON_LPC                            policy<{'arm64': 'y'}>
+CONFIG_HISI_DMA                                 policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_HISI_FEMAC                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HISI_HIKEY_USB                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HISI_PMU                                 policy<{'arm64': 'm'}>
+CONFIG_HISI_THERMAL                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HIST_TRIGGERS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HIST_TRIGGERS_DEBUG                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HIX5HD2_GMAC                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HMC425                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HMC6352                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HMC_DRV                                  policy<{'s390x': 'm'}>
+CONFIG_HMEM_REPORTING                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HMM_MIRROR                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HMS_ANYBUSS_BUS                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HMS_PROFINET                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HNS                                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HNS3                                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HNS3_DCB                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HNS3_ENET                                policy<{'arm64': 'm'}>
+CONFIG_HNS3_HCLGE                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HNS3_HCLGEVF                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HNS_DSAF                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HNS_ENET                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HNS_MDIO                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HOLTEK_FF                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HOSTAP                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HOSTAP_CS                                policy<{'amd64': 'm'}>
+CONFIG_HOSTAP_FIRMWARE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HOSTAP_FIRMWARE_NVRAM                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HOSTAP_PCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HOSTAP_PLX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HOTPLUG_CPU                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HOTPLUG_PCI                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HOTPLUG_PCI_ACPI                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HOTPLUG_PCI_ACPI_IBM                     policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HOTPLUG_PCI_CPCI                         policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HOTPLUG_PCI_CPCI_GENERIC                 policy<{'amd64': 'm'}>
+CONFIG_HOTPLUG_PCI_CPCI_ZT5550                  policy<{'amd64': 'm'}>
+CONFIG_HOTPLUG_PCI_POWERNV                      policy<{'ppc64el': 'm'}>
+CONFIG_HOTPLUG_PCI_RPA                          policy<{'ppc64el': 'm'}>
+CONFIG_HOTPLUG_PCI_RPA_DLPAR                    policy<{'ppc64el': 'm'}>
+CONFIG_HOTPLUG_PCI_S390                         policy<{'s390x': 'y'}>
+CONFIG_HOTPLUG_SMT                              policy<{'amd64': 'y'}>
+CONFIG_HP03                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HP206C                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HPET                                     policy<{'amd64': 'y'}>
+CONFIG_HPET_EMULATE_RTC                         policy<{'amd64': 'y'}>
+CONFIG_HPET_MMAP                                policy<{'amd64': 'y'}>
+CONFIG_HPET_MMAP_DEFAULT                        policy<{'amd64': 'y'}>
+CONFIG_HPET_TIMER                               policy<{'amd64': 'y'}>
+CONFIG_HPFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HPWDT_NMI_DECODING                       policy<{'amd64': 'y'}>
+CONFIG_HP_ACCEL                                 policy<{'amd64': 'm'}>
+CONFIG_HP_ILO                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HP_WATCHDOG                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HP_WMI                                   policy<{'amd64': 'm'}>
+CONFIG_HSA_AMD                                  policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HSA_AMD_SVM                              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HSI                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HSI_BOARDINFO                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HSI_CHAR                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HSR                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HSU_DMA                                  policy<{'amd64': 'y'}>
+CONFIG_HT16K33                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HTC_EGPIO                                policy<{'armhf': 'y'}>
+CONFIG_HTC_I2CPLD                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_HTC_PASIC3                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HTS221                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HTS221_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HTS221_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HTU21                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HUAWEI_WMI                               policy<{'amd64': 'm'}>
+CONFIG_HUGETLBFS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HUGETLB_PAGE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HUGETLB_PAGE_FREE_VMEMMAP                policy<{'amd64': 'y'}>
+CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON     policy<{'amd64': 'n'}>
+CONFIG_HUGETLB_PAGE_SIZE_VARIABLE               policy<{'ppc64el': 'y'}>
+CONFIG_HVCS                                     policy<{'ppc64el': 'm'}>
+CONFIG_HVC_CONSOLE                              policy<{'ppc64el': 'y'}>
+CONFIG_HVC_DCC                                  policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_HVC_DRIVER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HVC_IRQ                                  policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_HVC_IUCV                                 policy<{'s390x': 'y'}>
+CONFIG_HVC_OLD_HVSI                             policy<{'ppc64el': 'y'}>
+CONFIG_HVC_OPAL                                 policy<{'ppc64el': 'y'}>
+CONFIG_HVC_RTAS                                 policy<{'ppc64el': 'y'}>
+CONFIG_HVC_XEN                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HVC_XEN_FRONTEND                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_HV_PERF_CTRS                             policy<{'ppc64el': 'y'}>
+CONFIG_HWLAT_TRACER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HWMON                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_HWMON_DEBUG_CHIP                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_HWMON_VID                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HWPOISON_INJECT                          policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_HWSPINLOCK                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_HWSPINLOCK_OMAP                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HWSPINLOCK_QCOM                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HWSPINLOCK_SPRD                          policy<{'arm64': 'm'}>
+CONFIG_HWSPINLOCK_SUN6I                         policy<{'arm64': 'm'}>
+CONFIG_HW_CONSOLE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HW_PERF_EVENTS                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_HW_RANDOM                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HW_RANDOM_AMD                            policy<{'amd64': 'm'}>
+CONFIG_HW_RANDOM_ARM_SMCCC_TRNG                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HW_RANDOM_BA431                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_HW_RANDOM_BCM2835                        policy<{'arm64': 'm'}>
+CONFIG_HW_RANDOM_CAVIUM                         policy<{'arm64': 'm'}>
+CONFIG_HW_RANDOM_CCTRNG                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'n'}>
+CONFIG_HW_RANDOM_EXYNOS                         policy<{'armhf': 'm'}>
+CONFIG_HW_RANDOM_HISI                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HW_RANDOM_IMX_RNGC                       policy<{'armhf-generic': 'm'}>
+CONFIG_HW_RANDOM_INTEL                          policy<{'amd64': 'm'}>
+CONFIG_HW_RANDOM_IPROC_RNG200                   policy<{'arm64': 'm'}>
+CONFIG_HW_RANDOM_MESON                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HW_RANDOM_MTK                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HW_RANDOM_NPCM                           policy<{'armhf': 'm'}>
+CONFIG_HW_RANDOM_OMAP                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HW_RANDOM_OMAP3_ROM                      policy<{'armhf-generic': 'm'}>
+CONFIG_HW_RANDOM_OPTEE                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_HW_RANDOM_POWERNV                        policy<{'ppc64el': 'm'}>
+CONFIG_HW_RANDOM_PSERIES                        policy<{'ppc64el': 'm'}>
+CONFIG_HW_RANDOM_S390                           policy<{'s390x': 'm'}>
+CONFIG_HW_RANDOM_TIMERIOMEM                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HW_RANDOM_TPM                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_HW_RANDOM_VIA                            policy<{'amd64': 'm'}>
+CONFIG_HW_RANDOM_VIRTIO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_HW_RANDOM_XGENE                          policy<{'arm64': 'm'}>
+CONFIG_HW_RANDOM_XIPHERA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_HX711                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_HYPERV                                   policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HYPERVISOR_GUEST                         policy<{'amd64': 'y'}>
+CONFIG_HYPERV_BALLOON                           policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HYPERV_IOMMU                             policy<{'amd64': 'y'}>
+CONFIG_HYPERV_KEYBOARD                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HYPERV_NET                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HYPERV_STORAGE                           policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HYPERV_TESTING                           policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_HYPERV_TIMER                             policy<{'amd64': 'y'}>
+CONFIG_HYPERV_UTILS                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HYPERV_VSOCKETS                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_HZ                                       policy<{'amd64': '250', 'amd64-lowlatency': '1000', 'arm64': '250', 'arm64-lowlatency': '1000', 'arm64-lowlatency-64k': '1000', 'armhf': '250', 'ppc64el': '250', 's390x': '100'}>
+CONFIG_HZ_100                                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_HZ_1000                                  policy<{'amd64': 'n', 'amd64-lowlatency': 'y', 'arm64': 'n', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HZ_200                                   policy<{'armhf': 'n'}>
+CONFIG_HZ_250                                   policy<{'amd64': 'y', 'amd64-lowlatency': 'n', 'arm64': 'y', 'arm64-lowlatency': 'n', 'arm64-lowlatency-64k': 'n', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_HZ_300                                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_HZ_500                                   policy<{'armhf': 'n'}>
+CONFIG_HZ_FIXED                                 policy<{'armhf': '0'}>
+CONFIG_HZ_PERIODIC                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_I2C                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_I2C_ALGOBIT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_I2C_ALGOPCA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_ALI1535                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_ALI1563                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_ALI15X3                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_ALTERA                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_AMD756                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_AMD756_S4882                         policy<{'amd64': 'm'}>
+CONFIG_I2C_AMD8111                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_AMD_MP2                              policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_I2C_ARB_GPIO_CHALLENGE                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_ASPEED                               policy<{'armhf': 'm'}>
+CONFIG_I2C_AXXIA                                policy<{'armhf-generic-lpae': 'm'}>
+CONFIG_I2C_BCM2835                              policy<{'arm64': 'm'}>
+CONFIG_I2C_BCM_IPROC                            policy<{'arm64': 'm'}>
+CONFIG_I2C_BOARDINFO                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_I2C_BRCMSTB                              policy<{'arm64': 'm'}>
+CONFIG_I2C_CADENCE                              policy<{'arm64': 'n'}>
+CONFIG_I2C_CBUS_GPIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_CHT_WC                               policy<{'amd64': 'm'}>
+CONFIG_I2C_COMPAT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_I2C_CP2615                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_CROS_EC_TUNNEL                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_DEBUG_ALGO                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_I2C_DEBUG_BUS                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_I2C_DEBUG_CORE                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_I2C_DEMUX_PINCTRL                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_DESIGNWARE_BAYTRAIL                  policy<{'amd64': 'y'}>
+CONFIG_I2C_DESIGNWARE_CORE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_I2C_DESIGNWARE_PCI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_DESIGNWARE_PLATFORM                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_I2C_DESIGNWARE_SLAVE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_I2C_DIOLAN_U2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_DLN2                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_EMEV2                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'm', 'ppc64el': 'n'}>
+CONFIG_I2C_EXYNOS5                              policy<{'armhf': 'm'}>
+CONFIG_I2C_FSI                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_GPIO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_GPIO_FAULT_INJECTOR                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_I2C_HELPER_AUTO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_I2C_HID_ACPI                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_I2C_HID_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_HID_OF                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_HID_OF_GOODIX                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_HISI                                 policy<{'arm64': 'm'}>
+CONFIG_I2C_HIX5HD2                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_I801                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_IMX                                  policy<{'arm64': 'm', 'armhf-generic': 'y'}>
+CONFIG_I2C_IMX_LPI2C                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_I2C_ISCH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_ISMT                                 policy<{'amd64': 'm'}>
+CONFIG_I2C_KEMPLD                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_LJCA                                 policy<{'amd64': 'm'}>
+CONFIG_I2C_MESON                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_MLXBF                                policy<{'arm64': 'm'}>
+CONFIG_I2C_MLXCPLD                              policy<{'amd64': 'm'}>
+CONFIG_I2C_MPC                                  policy<{'ppc64el': 'm'}>
+CONFIG_I2C_MT65XX                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_MUX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_I2C_MUX_GPIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_MUX_GPMUX                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_MUX_LTC4306                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_MUX_MLXCPLD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_MUX_PCA9541                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_MUX_PCA954x                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_MUX_PINCTRL                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_MUX_REG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_MV64XXX                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_NFORCE2                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_NFORCE2_S4985                        policy<{'amd64': 'm'}>
+CONFIG_I2C_NOMADIK                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_NPCM7XX                              policy<{'armhf': 'm'}>
+CONFIG_I2C_NVIDIA_GPU                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_OCORES                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_OMAP                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_I2C_OPAL                                 policy<{'ppc64el': 'y'}>
+CONFIG_I2C_OWL                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_PARPORT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_PCA_PLATFORM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_PIIX4                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_PXA                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_PXA_SLAVE                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_I2C_QCOM_CCI                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_QCOM_GENI                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_QUP                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_RCAR                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_RIIC                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_RK3X                                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_ROBOTFUZZ_OSIF                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_S3C2410                              policy<{'armhf': 'y'}>
+CONFIG_I2C_SCMI                                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_I2C_SH_MOBILE                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_SI470X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_SI4713                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_SIMTEC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_SIS5595                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_SIS630                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_SIS96X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_SLAVE                                policy<{'amd64': 'n', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_I2C_SLAVE_EEPROM                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_SLAVE_TESTUNIT                       policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_I2C_SMBUS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_SPRD                                 policy<{'arm64': 'y'}>
+CONFIG_I2C_STUB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_I2C_SYNQUACER                            policy<{'arm64': 'm'}>
+CONFIG_I2C_TAOS_EVM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_TEGRA                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_I2C_TEGRA_BPMP                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_I2C_THUNDERX                             policy<{'arm64': 'm'}>
+CONFIG_I2C_TINY_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_UNIPHIER                             policy<{'armhf': 'n'}>
+CONFIG_I2C_UNIPHIER_F                           policy<{'armhf': 'n'}>
+CONFIG_I2C_VERSATILE                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_I2C_VIA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_VIAPRO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_VIPERBOARD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I2C_VIRTIO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_XGENE_SLIMPRO                        policy<{'arm64': 'm'}>
+CONFIG_I2C_XILINX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I2C_XLP9XX                               policy<{'arm64': 'm'}>
+CONFIG_I3C                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I40E                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I40EVF                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_I40E_DCB                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_I6300ESB_WDT                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_I82092                                   policy<{'amd64': 'm'}>
+CONFIG_I8253_LOCK                               policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_I8K                                      policy<{'amd64': 'm'}>
+CONFIG_IA32_EMULATION                           policy<{'amd64': 'y'}>
+CONFIG_IA32_FEAT_CTL                            policy<{'amd64': 'y'}>
+CONFIG_IAQCORE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IAVF                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IB700_WDT                                policy<{'amd64': 'm'}>
+CONFIG_IBMASR                                   policy<{'amd64': 'm'}>
+CONFIG_IBMVETH                                  policy<{'ppc64el': 'm'}>
+CONFIG_IBMVIO                                   policy<{'ppc64el': 'y'}>
+CONFIG_IBMVMC                                   policy<{'ppc64el': 'm'}>
+CONFIG_IBM_ASM                                  policy<{'amd64': 'm'}>
+CONFIG_IBM_BSR                                  policy<{'ppc64el': 'm'}>
+CONFIG_IBM_PARTITION                            policy<{'s390x': 'y'}>
+CONFIG_IBM_RTL                                  policy<{'amd64': 'm'}>
+CONFIG_ICE                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ICP10100                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ICPLUS_PHY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ICS932S401                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ICST                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IDEAPAD_LAPTOP                           policy<{'amd64': 'm'}>
+CONFIG_IDLE_INJECT                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IE6XX_WDT                                policy<{'amd64': 'm'}>
+CONFIG_IEEE802154                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_IEEE802154_6LOWPAN                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_ADF7242                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_AT86RF230                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_AT86RF230_DEBUGFS             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IEEE802154_ATUSB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_CA8210                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_CA8210_DEBUGFS                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IEEE802154_CC2520                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_DRIVERS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_FAKELB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_HWSIM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_MCR20A                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_MRF24J40                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IEEE802154_NL802154_EXPERIMENTAL         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IEEE802154_SOCKET                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IFB                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IFCVF                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IGB                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IGBVF                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IGB_DCA                                  policy<{'amd64': 'y'}>
+CONFIG_IGB_HWMON                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IGC                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_IIO_ADIS_LIB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ADIS_LIB_BUFFER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IIO_BUFFER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IIO_BUFFER_CB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_BUFFER_DMA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_BUFFER_DMAENGINE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_BUFFER_HW_CONSUMER                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_CONFIGFS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_CONSUMERS_PER_TRIGGER                policy<{'amd64': '2', 'arm64': '2', 'armhf': '2', 'ppc64el': '2'}>
+CONFIG_IIO_CROS_EC_ACCEL_LEGACY                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_CROS_EC_BARO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_CROS_EC_LIGHT_PROX                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_CROS_EC_SENSORS                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_CROS_EC_SENSORS_CORE                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_CROS_EC_SENSORS_LID_ANGLE            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_HRTIMER_TRIGGER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_INTERRUPT_TRIGGER                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_KFIFO_BUF                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_MS_SENSORS_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_MUX                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_RESCALE                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_SCMI                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IIO_SIMPLE_DUMMY                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_SSP_SENSORHUB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_SSP_SENSORS_COMMONS                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_ACCEL_3AXIS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_ACCEL_I2C_3AXIS                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_ACCEL_SPI_3AXIS                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_GYRO_3AXIS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_GYRO_I2C_3AXIS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_GYRO_SPI_3AXIS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM6DSX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM6DSX_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM6DSX_I3C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM6DSX_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM9DS0                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM9DS0_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_LSM9DS0_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_MAGN_3AXIS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_MAGN_I2C_3AXIS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_MAGN_SPI_3AXIS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_PRESS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_PRESS_I2C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_PRESS_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_SENSORS_CORE                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_SENSORS_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_ST_SENSORS_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_SW_DEVICE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_SW_TRIGGER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_SYSFS_TRIGGER                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_TIGHTLOOP_TRIGGER                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_TRIGGER                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IIO_TRIGGERED_BUFFER                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IIO_TRIGGERED_EVENT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IKCONFIG                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IKHEADERS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ILLEGAL_POINTER_VALUE                    policy<{'amd64': '0xdead000000000000', 'arm64': '0xdead000000000000', 'ppc64el': '0x5deadbeef0000000'}>
+CONFIG_IMA_APPRAISE_BOOTPARAM                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA_APPRAISE_BUILD_POLICY                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_APPRAISE_MODSIG                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA_BLACKLIST_KEYRING                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_DEFAULT_HASH                         policy<{'amd64': '"sha1"', 'arm64': '"sha1"', 'armhf': '"sha1"', 'ppc64el': '"sha256"', 's390x': '"sha1"'}>
+CONFIG_IMA_DEFAULT_HASH_SHA1                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_IMA_DEFAULT_HASH_SHA512                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_DEFAULT_TEMPLATE                     policy<{'amd64': '"ima-ng"', 'arm64': '"ima-ng"', 'armhf': '"ima-ng"', 'ppc64el': '"ima-sig"', 's390x': '"ima-ng"'}>
+CONFIG_IMA_DISABLE_HTABLE                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_LOAD_X509                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IMA_LSM_RULES                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA_MEASURE_ASYMMETRIC_KEYS              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA_MEASURE_PCR_IDX                      policy<{'amd64': '10', 'arm64': '10', 'armhf': '10', 'ppc64el': '10', 's390x': '10'}>
+CONFIG_IMA_NG_TEMPLATE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_IMA_QUEUE_EARLY_BOOT_KEYS                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IMA_SECURE_AND_OR_TRUSTED_BOOT           policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_IMG_ASCII_LCD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IMX2_WDT                                 policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX7D_ADC                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX7ULP_WDT                              policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX8MM_THERMAL                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_DMA                                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_DSP                                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_GPCV2                                policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_IMX_GPCV2_PM_DOMAINS                     policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_IMX_INTMUX                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_IMX_IPUV3_CORE                           policy<{'armhf': 'm'}>
+CONFIG_IMX_IRQSTEER                             policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_IMX_MBOX                                 policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_REMOTEPROC                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_SCU                                  policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_IMX_SCU_PD                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_IMX_SC_THERMAL                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_SC_WDT                               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_SDMA                                 policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_THERMAL                              policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_IMX_WEIM                                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_INA2XX_ADC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INDIRECT_PIO                             policy<{'arm64': 'y'}>
+CONFIG_INET                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INET6_AH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET6_ESP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET6_ESPINTCP                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INET6_ESP_OFFLOAD                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET6_IPCOMP                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET6_TUNNEL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET6_XFRM_TUNNEL                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_AH                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_DCCP_DIAG                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_DIAG                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_DIAG_DESTROY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INET_ESP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_ESPINTCP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INET_ESP_OFFLOAD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_IPCOMP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_MPTCP_DIAG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_RAW_DIAG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_SCTP_DIAG                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_TABLE_PERTURB_ORDER                 policy<{'amd64': '16', 'arm64': '16', 'armhf': '16', 'ppc64el': '16', 's390x': '16'}>
+CONFIG_INET_TCP_DIAG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_TUNNEL                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_UDP_DIAG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INET_XFRM_TUNNEL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_ADDR_TRANS                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INFINIBAND_ADDR_TRANS_CONFIGFS           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INFINIBAND_BNXT_RE                       policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_INFINIBAND_CXGB4                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INFINIBAND_EFA                           policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_INFINIBAND_HFI1                          policy<{'amd64': 'm'}>
+CONFIG_INFINIBAND_HNS                           policy<{'arm64': 'm'}>
+CONFIG_INFINIBAND_HNS_HIP06                     policy<{'arm64': 'y'}>
+CONFIG_INFINIBAND_HNS_HIP08                     policy<{'arm64': 'y'}>
+CONFIG_INFINIBAND_IPOIB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_IPOIB_CM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INFINIBAND_IPOIB_DEBUG                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INFINIBAND_IRDMA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INFINIBAND_ISER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_ISERT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_MTHCA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_MTHCA_DEBUG                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INFINIBAND_OCRDMA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_INFINIBAND_ON_DEMAND_PAGING              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INFINIBAND_OPA_VNIC                      policy<{'amd64': 'm'}>
+CONFIG_INFINIBAND_QEDR                          policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_INFINIBAND_QIB                           policy<{'amd64': 'm'}>
+CONFIG_INFINIBAND_QIB_DCA                       policy<{'amd64': 'y'}>
+CONFIG_INFINIBAND_RDMAVT                        policy<{'amd64': 'm'}>
+CONFIG_INFINIBAND_RTRS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_RTRS_CLIENT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_RTRS_SERVER                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_SRP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_SRPT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_USER_ACCESS                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_USER_MAD                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INFINIBAND_USER_MEM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INFINIBAND_USNIC                         policy<{'amd64': 'm'}>
+CONFIG_INFINIBAND_VIRT_DMA                      policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INFINIBAND_VMWARE_PVRDMA                 policy<{'amd64': 'm', 'arm64-generic': 'm', 'arm64-lowlatency': 'm', 'armhf': 'm'}>
+CONFIG_INFTL                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INITRAMFS_SOURCE                         policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_INIT_ENV_ARG_LIMIT                       policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32', 's390x': '32'}>
+CONFIG_INIT_ON_ALLOC_DEFAULT_ON                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INIT_ON_FREE_DEFAULT_ON                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INIT_STACK_NONE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INLINE_READ_LOCK                         policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_READ_LOCK_BH                      policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_READ_LOCK_IRQ                     policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_READ_LOCK_IRQSAVE                 policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_READ_TRYLOCK                      policy<{'s390x': 'y'}>
+CONFIG_INLINE_READ_UNLOCK                       policy<{'amd64': 'y', 'amd64-lowlatency': '-', 'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INLINE_READ_UNLOCK_BH                    policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_READ_UNLOCK_IRQ                   policy<{'amd64': 'y', 'amd64-lowlatency': '-', 'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INLINE_READ_UNLOCK_IRQRESTORE            policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_LOCK                         policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_LOCK_BH                      policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_LOCK_IRQ                     policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_LOCK_IRQSAVE                 policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_TRYLOCK                      policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_TRYLOCK_BH                   policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_UNLOCK_BH                    policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_UNLOCK_IRQ                   policy<{'amd64': 'y', 'amd64-lowlatency': '-', 'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE            policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_LOCK                        policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_LOCK_BH                     policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_LOCK_IRQ                    policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_LOCK_IRQSAVE                policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_TRYLOCK                     policy<{'s390x': 'y'}>
+CONFIG_INLINE_WRITE_UNLOCK                      policy<{'amd64': 'y', 'amd64-lowlatency': '-', 'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_UNLOCK_BH                   policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_UNLOCK_IRQ                  policy<{'amd64': 'y', 'amd64-lowlatency': '-', 'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE           policy<{'arm64': 'y', 'arm64-lowlatency': '-', 'arm64-lowlatency-64k': '-', 's390x': 'y'}>
+CONFIG_INOTIFY_USER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INPUT                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INPUT_88PM80X_ONKEY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_88PM860X_ONKEY                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_AD714X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_AD714X_I2C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_AD714X_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_ADXL34X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_ADXL34X_I2C                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_ADXL34X_SPI                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_APANEL                             policy<{'amd64': 'm'}>
+CONFIG_INPUT_ARIZONA_HAPTICS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_ATC260X_ONKEY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_ATI_REMOTE2                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_ATLAS_BTNS                         policy<{'amd64': 'm'}>
+CONFIG_INPUT_ATMEL_CAPTOUCH                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_AXP20X_PEK                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_BMA150                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_CM109                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_CMA3000                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_CMA3000_I2C                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_CPCAP_PWRBUTTON                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DA7280_HAPTICS                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DA9052_ONKEY                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DA9055_ONKEY                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DA9063_ONKEY                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DRV260X_HAPTICS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DRV2665_HAPTICS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_DRV2667_HAPTICS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_E3X0_BUTTON                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_EVBUG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_INPUT_EVDEV                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INPUT_FF_MEMLESS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_INPUT_GPIO_BEEPER                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_GPIO_DECODER                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_GPIO_ROTARY_ENCODER                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_GPIO_VIBRA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_HISI_POWERKEY                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INPUT_IDEAPAD_SLIDEBAR                   policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_IMS_PCU                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_IQS269A                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_IQS626A                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_JOYDEV                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_INPUT_JOYSTICK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_KEYBOARD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_KEYSPAN_REMOTE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_KXTJ9                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_LEDS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MATRIXKMAP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_INPUT_MAX77650_ONKEY                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MAX77693_HAPTIC                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MAX8925_ONKEY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MAX8997_HAPTIC                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MC13783_PWRBUTTON                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MISC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_MMA8450                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_MOUSE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_MOUSEDEV                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_MOUSEDEV_PSAUX                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_INPUT_MOUSEDEV_SCREEN_X                  policy<{'amd64': '1024', 'arm64': '1024', 'armhf': '1024', 'ppc64el': '1024'}>
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y                  policy<{'amd64': '768', 'arm64': '768', 'armhf': '768', 'ppc64el': '768'}>
+CONFIG_INPUT_PALMAS_PWRBUTTON                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PCAP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PCF50633_PMU                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PCF8574                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PCSPKR                             policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PM8941_PWRKEY                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INPUT_PM8XXX_VIBRATOR                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INPUT_PMIC8XXX_PWRKEY                    policy<{'armhf': 'm'}>
+CONFIG_INPUT_POWERMATE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PWM_BEEPER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_PWM_VIBRA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_RAVE_SP_PWRBUTTON                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_REGULATOR_HAPTIC                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_RETU_PWRBUTTON                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_RK805_PWRKEY                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_SC27XX_VIBRA                       policy<{'arm64': 'm'}>
+CONFIG_INPUT_SOC_BUTTON_ARRAY                   policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_INPUT_SPARSEKMAP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_INPUT_STPMIC1_ONKEY                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_TABLET                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_TOUCHSCREEN                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INPUT_TPS65218_PWRBUTTON                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_TWL4030_PWRBUTTON                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_TWL4030_VIBRA                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_TWL6040_VIBRA                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_WM831X_ON                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INPUT_XEN_KBDDEV_FRONTEND                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_INPUT_YEALINK                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INSTRUCTION_DECODER                      policy<{'amd64': 'y'}>
+CONFIG_INT3406_THERMAL                          policy<{'amd64': 'm'}>
+CONFIG_INT340X_THERMAL                          policy<{'amd64': 'm'}>
+CONFIG_INTEGRITY                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTEGRITY_ASYMMETRIC_KEYS                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTEGRITY_AUDIT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTEGRITY_SIGNATURE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTEGRITY_TRUSTED_KEYRING                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTEL_ATOMISP                            policy<{'amd64': 'y'}>
+CONFIG_INTEL_ATOMISP2_LED                       policy<{'amd64': 'm'}>
+CONFIG_INTEL_ATOMISP2_PDX86                     policy<{'amd64': 'y'}>
+CONFIG_INTEL_BXTWC_PMIC_TMU                     policy<{'amd64': 'm'}>
+CONFIG_INTEL_BXT_PMIC_THERMAL                   policy<{'amd64': 'm'}>
+CONFIG_INTEL_CHTDC_TI_PWRBTN                    policy<{'amd64': 'm'}>
+CONFIG_INTEL_CHT_INT33FE                        policy<{'amd64': 'm'}>
+CONFIG_INTEL_GTT                                policy<{'amd64': 'y'}>
+CONFIG_INTEL_HID_EVENT                          policy<{'amd64': 'm'}>
+CONFIG_INTEL_IDLE                               policy<{'amd64': 'y'}>
+CONFIG_INTEL_IDMA64                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INTEL_IDXD                               policy<{'amd64': 'm'}>
+CONFIG_INTEL_IDXD_BUS                           policy<{'amd64': 'm'}>
+CONFIG_INTEL_IDXD_COMPAT                        policy<{'amd64': 'n'}>
+CONFIG_INTEL_IDXD_PERFMON                       policy<{'amd64': 'y'}>
+CONFIG_INTEL_IDXD_SVM                           policy<{'amd64': 'y'}>
+CONFIG_INTEL_INT0002_VGPIO                      policy<{'amd64': 'm'}>
+CONFIG_INTEL_IOATDMA                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_IOMMU                              policy<{'amd64': 'y'}>
+CONFIG_INTEL_IOMMU_FLOPPY_WA                    policy<{'amd64': 'y'}>
+CONFIG_INTEL_IOMMU_SCALABLE_MODE_DEFAULT_ON     policy<{'amd64': 'n'}>
+CONFIG_INTEL_IOMMU_SVM                          policy<{'amd64': 'y'}>
+CONFIG_INTEL_IPS                                policy<{'amd64': 'm'}>
+CONFIG_INTEL_ISH_FIRMWARE_DOWNLOADER            policy<{'amd64': 'm'}>
+CONFIG_INTEL_ISH_HID                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_LDMA                               policy<{'amd64': 'y'}>
+CONFIG_INTEL_MEI                                policy<{'amd64': 'm'}>
+CONFIG_INTEL_MEI_HDCP                           policy<{'amd64': 'm'}>
+CONFIG_INTEL_MEI_ME                             policy<{'amd64': 'm'}>
+CONFIG_INTEL_MEI_TXE                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_MEI_VSC                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_MEI_WDT                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_MENLOW                             policy<{'amd64': 'm'}>
+CONFIG_INTEL_MRFLD_ADC                          policy<{'amd64': 'm'}>
+CONFIG_INTEL_MRFLD_PWRBTN                       policy<{'amd64': 'm'}>
+CONFIG_INTEL_OAKTRAIL                           policy<{'amd64': 'm'}>
+CONFIG_INTEL_PCH_THERMAL                        policy<{'amd64': 'm'}>
+CONFIG_INTEL_PMC_CORE                           policy<{'amd64': 'y'}>
+CONFIG_INTEL_PMT_CLASS                          policy<{'amd64': 'm'}>
+CONFIG_INTEL_PMT_CRASHLOG                       policy<{'amd64': 'm'}>
+CONFIG_INTEL_PMT_TELEMETRY                      policy<{'amd64': 'm'}>
+CONFIG_INTEL_POWERCLAMP                         policy<{'amd64': 'm'}>
+CONFIG_INTEL_PUNIT_IPC                          policy<{'amd64': 'm'}>
+CONFIG_INTEL_QEP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INTEL_RAPL                               policy<{'amd64': 'm'}>
+CONFIG_INTEL_RAPL_CORE                          policy<{'amd64': 'm'}>
+CONFIG_INTEL_RST                                policy<{'amd64': 'm'}>
+CONFIG_INTEL_SAR_INT1092                        policy<{'amd64': 'm'}>
+CONFIG_INTEL_SCU                                policy<{'amd64': 'y'}>
+CONFIG_INTEL_SCU_IPC                            policy<{'amd64': 'y'}>
+CONFIG_INTEL_SCU_IPC_UTIL                       policy<{'amd64': 'm'}>
+CONFIG_INTEL_SCU_PCI                            policy<{'amd64': 'y'}>
+CONFIG_INTEL_SCU_PLATFORM                       policy<{'amd64': 'm'}>
+CONFIG_INTEL_SKL_INT3472                        policy<{'amd64': 'm'}>
+CONFIG_INTEL_SMARTCONNECT                       policy<{'amd64': 'm'}>
+CONFIG_INTEL_SOC_DTS_IOSF_CORE                  policy<{'amd64': 'm'}>
+CONFIG_INTEL_SOC_DTS_THERMAL                    policy<{'amd64': 'm'}>
+CONFIG_INTEL_SOC_PMIC                           policy<{'amd64': 'y'}>
+CONFIG_INTEL_SOC_PMIC_BXTWC                     policy<{'amd64': 'm'}>
+CONFIG_INTEL_SOC_PMIC_CHTDC_TI                  policy<{'amd64': 'm'}>
+CONFIG_INTEL_SOC_PMIC_CHTWC                     policy<{'amd64': 'y'}>
+CONFIG_INTEL_SOC_PMIC_MRFLD                     policy<{'amd64': 'm'}>
+CONFIG_INTEL_SPEED_SELECT_INTERFACE             policy<{'amd64': 'm'}>
+CONFIG_INTEL_STRATIX10_RSU                      policy<{'arm64': 'm'}>
+CONFIG_INTEL_STRATIX10_SERVICE                  policy<{'arm64': 'm'}>
+CONFIG_INTEL_TCC_COOLING                        policy<{'amd64': 'm'}>
+CONFIG_INTEL_TELEMETRY                          policy<{'amd64': 'm'}>
+CONFIG_INTEL_TH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTEL_TH_ACPI                            policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_INTEL_TH_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INTEL_TH_GTH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTEL_TH_MSU                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTEL_TH_PCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTEL_TH_PTI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTEL_TH_STH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTEL_TURBO_MAX_3                        policy<{'amd64': 'y'}>
+CONFIG_INTEL_TXT                                policy<{'amd64': 'y'}>
+CONFIG_INTEL_UNCORE_FREQ_CONTROL                policy<{'amd64': 'm'}>
+CONFIG_INTEL_VBTN                               policy<{'amd64': 'm'}>
+CONFIG_INTEL_VSC                                policy<{'amd64': 'm', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INTEL_VSC_ACE                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_VSC_ACE_DEBUG                      policy<{'amd64': 'm', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INTEL_VSC_CSI                            policy<{'amd64': 'm'}>
+CONFIG_INTEL_VSC_PSE                            policy<{'amd64': 'm', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INTEL_WMI                                policy<{'amd64': 'y'}>
+CONFIG_INTEL_WMI_SBL_FW_UPDATE                  policy<{'amd64': 'm'}>
+CONFIG_INTEL_WMI_THUNDERBOLT                    policy<{'amd64': 'm'}>
+CONFIG_INTEL_XWAY_PHY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_INTERCONNECT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_INTERCONNECT_EXYNOS                      policy<{'armhf': 'm'}>
+CONFIG_INTERCONNECT_IMX                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_INTERCONNECT_IMX8MM                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_INTERCONNECT_IMX8MN                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_INTERCONNECT_IMX8MQ                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_INTERCONNECT_QCOM                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_INTERCONNECT_QCOM_BCM_VOTER              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_MSM8916                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_MSM8939                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_MSM8974                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_OSM_L3                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_QCS404                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_RPMH                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_RPMH_POSSIBLE          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_INTERCONNECT_QCOM_SC7180                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SC7280                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SC8180X                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SDM660                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SDM845                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SDX55                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SM8150                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SM8250                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SM8350                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_QCOM_SMD_RPM                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_INTERCONNECT_SAMSUNG                     policy<{'armhf': 'y'}>
+CONFIG_INTERRUPT_CNT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INTERVAL_TREE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_INTERVAL_TREE_TEST                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_INV_ICM42600                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INV_ICM42600_I2C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INV_ICM42600_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INV_MPU6050_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INV_MPU6050_IIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_INV_MPU6050_SPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IOASID                                   policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_IOMMU_API                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IOMMU_DEBUG                              policy<{'amd64': 'n'}>
+CONFIG_IOMMU_DEFAULT_DMA_LAZY                   policy<{'amd64': 'y', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IOMMU_DEFAULT_DMA_STRICT                 policy<{'amd64': 'n', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IOMMU_DEFAULT_PASSTHROUGH                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IOMMU_DMA                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_IOMMU_HELPER                             policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IOMMU_IOVA                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IOMMU_IO_PGTABLE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_IOMMU_IO_PGTABLE_ARMV7S                  policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_IOMMU_IO_PGTABLE_LPAE                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_IOMMU_IO_PGTABLE_LPAE_SELFTEST           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_IOMMU_SUPPORT                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IOMMU_SVA_LIB                            policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_IONIC                                    policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_IOSCHED_BFQ                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IOSF_MBI                                 policy<{'amd64': 'y'}>
+CONFIG_IOSF_MBI_DEBUG                           policy<{'amd64': 'y'}>
+CONFIG_IOSM                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IO_DELAY_0X80                            policy<{'amd64': 'n'}>
+CONFIG_IO_DELAY_0XED                            policy<{'amd64': 'y'}>
+CONFIG_IO_DELAY_NONE                            policy<{'amd64': 'n'}>
+CONFIG_IO_DELAY_UDELAY                          policy<{'amd64': 'n'}>
+CONFIG_IO_EVENT_IRQ                             policy<{'ppc64el': 'y'}>
+CONFIG_IO_STRICT_DEVMEM                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IO_URING                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IO_WQ                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP6_NF_FILTER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_IPTABLES                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MANGLE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_AH                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_EUI64                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_FRAG                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_HL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_IPV6HEADER                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_MH                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_OPTS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_RPFILTER                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_RT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_MATCH_SRH                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_NAT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_RAW                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_SECURITY                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_TARGET_HL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_TARGET_MASQUERADE                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_TARGET_NPT                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_TARGET_REJECT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP6_NF_TARGET_SYNPROXY                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPACK_BUS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_IPC_NS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPMB_DEVICE_INTERFACE                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPMI_DEVICE_INTERFACE                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPMI_DMI_DECODE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_IPMI_HANDLER                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_IPMI_KCS_BMC                             policy<{'armhf': 'm'}>
+CONFIG_IPMI_KCS_BMC_CDEV_IPMI                   policy<{'armhf': 'm'}>
+CONFIG_IPMI_KCS_BMC_SERIO                       policy<{'armhf': 'm'}>
+CONFIG_IPMI_PANIC_EVENT                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IPMI_PLAT_DATA                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IPMI_POWERNV                             policy<{'ppc64el': 'm'}>
+CONFIG_IPMI_POWEROFF                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPMI_SI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPMI_SSIF                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPMI_WATCHDOG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPQ_APSS_6018                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPQ_APSS_PLL                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPQ_GCC_4019                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPQ_GCC_6018                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPQ_GCC_806X                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPQ_GCC_8074                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPQ_LCC_806X                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IPV6_FOU                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_FOU_TUNNEL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_GRE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_ILA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_IOAM6_LWTUNNEL                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_MIP6                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_MROUTE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_MROUTE_MULTIPLE_TABLES              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_MULTIPLE_TABLES                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_NDISC_NODETYPE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_OPTIMISTIC_DAD                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IPV6_PIMSM_V2                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_ROUTER_PREF                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_ROUTE_INFO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_RPL_LWTUNNEL                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IPV6_SEG6_BPF                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_SEG6_HMAC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_SEG6_LWTUNNEL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_SIT                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_SIT_6RD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_SUBTREES                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPV6_TUNNEL                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPV6_VTI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPVLAN                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPVLAN_L3S                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IPVTAP                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IPW2100                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPW2100_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IPW2100_MONITOR                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IPW2200                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IPW2200_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IPW2200_MONITOR                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IPW2200_PROMISCUOUS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IPW2200_QOS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IPW2200_RADIOTAP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IPWIRELESS                               policy<{'amd64': 'm'}>
+CONFIG_IP_ADVANCED_ROUTER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_DCCP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_DCCP_CCID2_DEBUG                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IP_DCCP_CCID3                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_IP_DCCP_CCID3_DEBUG                      policy<{'s390x': 'n'}>
+CONFIG_IP_DCCP_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IP_DCCP_TFRC_LIB                         policy<{'s390x': 'y'}>
+CONFIG_IP_FIB_TRIE_STATS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_MROUTE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_MROUTE_COMMON                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_MROUTE_MULTIPLE_TABLES                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_MULTICAST                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_MULTIPLE_TABLES                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_NF_ARPFILTER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_ARPTABLES                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_ARP_MANGLE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_FILTER                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_IPTABLES                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_MANGLE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_MATCH_AH                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_MATCH_ECN                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_MATCH_RPFILTER                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_MATCH_TTL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_NAT                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_RAW                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_SECURITY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_CLUSTERIP                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_ECN                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_MASQUERADE                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_NETMAP                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_REDIRECT                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_REJECT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_SYNPROXY                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_NF_TARGET_TTL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_PIMSM_V1                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_PIMSM_V2                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_ROUTE_CLASSID                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_ROUTE_MULTIPATH                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_ROUTE_VERBOSE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_SCTP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_BITMAP_IP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_BITMAP_IPMAC                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_BITMAP_PORT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_IP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_IPMAC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_IPMARK                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_IPPORT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_IPPORTIP                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_IPPORTNET                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_MAC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_NET                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_NETIFACE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_NETNET                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_NETPORT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_HASH_NETPORTNET                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_LIST_SET                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_SET_MAX                               policy<{'amd64': '256', 'arm64': '256', 'armhf': '256', 'ppc64el': '256', 's390x': '256'}>
+CONFIG_IP_VS                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_DEBUG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IP_VS_DH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_FO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_FTP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_IPV6                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_LBLC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_LBLCR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_LC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_MH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_MH_TAB_INDEX                       policy<{'amd64': '12', 'arm64': '12', 'armhf': '12', 'ppc64el': '12', 's390x': '12'}>
+CONFIG_IP_VS_NFCT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_NQ                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_OVF                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_PE_SIP                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_PROTO_AH                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_PROTO_AH_ESP                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_PROTO_ESP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_PROTO_SCTP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_PROTO_TCP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_PROTO_UDP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IP_VS_RR                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_SED                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_SH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_SH_TAB_BITS                        policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8', 's390x': '8'}>
+CONFIG_IP_VS_TAB_BITS                           policy<{'amd64': '12', 'arm64': '12', 'armhf': '12', 'ppc64el': '12', 's390x': '12'}>
+CONFIG_IP_VS_TWOS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_IP_VS_WLC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IP_VS_WRR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IQS620AT_TEMP                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IQS621_ALS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IQS624_POS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IRQCHIP                                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IRQSOFF_TRACER                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_IRQ_ALL_CPUS                             policy<{'ppc64el': 'y'}>
+CONFIG_IRQ_BYPASS_MANAGER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_IRQ_CROSSBAR                             policy<{'armhf': 'y'}>
+CONFIG_IRQ_DOMAIN                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IRQ_DOMAIN_HIERARCHY                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_IRQ_FORCED_THREADING                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IRQ_MSI_IOMMU                            policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_IRQ_POLL                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IRQ_REMAP                                policy<{'amd64': 'y'}>
+CONFIG_IRQ_TIME_ACCOUNTING                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IRQ_UNIPHIER_AIDET                       policy<{'armhf': 'y'}>
+CONFIG_IRQ_WORK                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_IR_ENE                                   policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_IR_FINTEK                                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_IR_GPIO_CIR                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_GPIO_TX                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_HIX5HD2                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_IGORPLUGUSB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_IGUANA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_IMON                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_IMON_DECODER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_IMON_RAW                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_ITE_CIR                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_IR_JVC_DECODER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_MCEUSB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_MCE_KBD_DECODER                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_MESON                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IR_MESON_TX                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IR_MTK                                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_IR_NEC_DECODER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_NUVOTON                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_IR_PWM_TX                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_RC5_DECODER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_RC6_DECODER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_RCMM_DECODER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_REDRAT3                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_RX51                                  policy<{'armhf': 'm'}>
+CONFIG_IR_SANYO_DECODER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_SERIAL                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_SERIAL_TRANSMITTER                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IR_SHARP_DECODER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_SIR                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_SONY_DECODER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_SPI                                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_STREAMZAP                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_SUNXI                                 policy<{'arm64': 'm'}>
+CONFIG_IR_TOY                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_TTUSBIR                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IR_WINBOND_CIR                           policy<{'amd64': 'm'}>
+CONFIG_IR_XMP_DECODER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ISA_BUS                                  policy<{'amd64': 'y'}>
+CONFIG_ISA_BUS_API                              policy<{'amd64': 'y'}>
+CONFIG_ISA_DMA_API                              policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_ISCSI_BOOT_SYSFS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ISCSI_IBFT                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_ISCSI_IBFT_FIND                          policy<{'amd64': 'y'}>
+CONFIG_ISCSI_TARGET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ISCSI_TARGET_CXGB4                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ISCSI_TCP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ISDN                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ISDN_CAPI                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ISDN_CAPI_MIDDLEWARE                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ISL29003                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ISL29020                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ISL29125                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ISL29501                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ISO9660_FS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_IT8712F_WDT                              policy<{'amd64': 'm'}>
+CONFIG_IT87_WDT                                 policy<{'amd64': 'm'}>
+CONFIG_ITCO_VENDOR_SUPPORT                      policy<{'amd64': 'y'}>
+CONFIG_ITCO_WDT                                 policy<{'amd64': 'm'}>
+CONFIG_ITG3200                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IUCV                                     policy<{'s390x': 'y'}>
+CONFIG_IWL3945                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IWL4965                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IWLDVM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IWLEGACY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IWLEGACY_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IWLEGACY_DEBUGFS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IWLMVM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IWLWIFI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IWLWIFI_BCAST_FILTERING                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IWLWIFI_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_IWLWIFI_DEBUGFS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IWLWIFI_DEVICE_TRACING                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IWLWIFI_LEDS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IWLWIFI_OPMODE_MODULAR                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IWMMXT                                   policy<{'armhf': 'y'}>
+CONFIG_IXGB                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IXGBE                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IXGBEVF                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_IXGBEVF_IPSEC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IXGBE_DCA                                policy<{'amd64': 'y'}>
+CONFIG_IXGBE_DCB                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IXGBE_HWMON                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_IXGBE_IPSEC                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JAILHOUSE_GUEST                          policy<{'amd64': 'y'}>
+CONFIG_JBD2                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_JBD2_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_JFFS2_CMODE_FAVOURLZO                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_CMODE_NONE                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFFS2_CMODE_PRIORITY                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFFS2_CMODE_SIZE                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFFS2_COMPRESSION_OPTIONS                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JFFS2_FS_DEBUG                           policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_JFFS2_FS_POSIX_ACL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_FS_SECURITY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_FS_WBUF_VERIFY                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFFS2_FS_WRITEBUFFER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_FS_XATTR                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_LZO                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_RTIME                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFFS2_RUBIN                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFFS2_SUMMARY                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFFS2_ZLIB                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFS_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_JFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_JFS_POSIX_ACL                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFS_SECURITY                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JFS_STATISTICS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JME                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_JOLIET                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_JOYSTICK_A3D                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_ADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_ADI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_ANALOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_AS5011                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_COBRA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_DB9                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_FSIA6B                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_GAMECON                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_GF2K                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_GRIP                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_GRIP_MP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_GUILLEMOT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_IFORCE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_IFORCE_232                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_IFORCE_USB                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_INTERACT                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_JOYDUMP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_MAGELLAN                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_PSXPAD_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_PSXPAD_SPI_FF                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JOYSTICK_PXRC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_QWIIC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_SIDEWINDER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_SPACEBALL                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_SPACEORB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_STINGER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_TMDC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_TURBOGRAFX                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_TWIDJOY                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_WALKERA0701                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_WARRIOR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_XPAD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JOYSTICK_XPAD_FF                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JOYSTICK_XPAD_LEDS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_JOYSTICK_ZHENHUA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JSA1212                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_JUMP_LABEL                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_JUMP_LABEL_FEATURE_CHECKS                policy<{'ppc64el': 'y'}>
+CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG           policy<{'ppc64el': 'n'}>
+CONFIG_K3_DMA                                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_K3_RTI_WATCHDOG                          policy<{'arm64': 'm'}>
+CONFIG_K3_THERMAL                               policy<{'arm64': 'm'}>
+CONFIG_KALLSYMS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KALLSYMS_ABSOLUTE_PERCPU                 policy<{'amd64': 'y'}>
+CONFIG_KALLSYMS_ALL                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KALLSYMS_BASE_RELATIVE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KARMA_PARTITION                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_KASAN                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_KCMP                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KCOV                                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_KCSAN                                    policy<{'amd64': 'n', 's390x': 'n'}>
+CONFIG_KDB_CONTINUE_CATASTROPHIC                policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_KDB_DEFAULT_ENABLE                       policy<{'amd64': '0x1', 'arm64': '0x1', 'armhf': '0x1', 'ppc64el': '0x1'}>
+CONFIG_KDB_KEYBOARD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_KEEMBAY_WATCHDOG                         policy<{'arm64': 'm'}>
+CONFIG_KEMPLD_WDT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KERNEL_BZIP2                             policy<{'amd64': 'n', 's390x': 'n'}>
+CONFIG_KERNEL_GZIP                              policy<{'amd64': 'n', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_KERNEL_LZ4                               policy<{'amd64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_KERNEL_LZMA                              policy<{'amd64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_KERNEL_LZO                               policy<{'amd64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_KERNEL_MODE_NEON                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_KERNEL_NOBP                              policy<{'s390x': 'n'}>
+CONFIG_KERNEL_START                             policy<{'ppc64el': '0xc000000000000000'}>
+CONFIG_KERNEL_UNCOMPRESSED                      policy<{'s390x': 'n'}>
+CONFIG_KERNEL_XZ                                policy<{'amd64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_KERNFS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KEXEC                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KEXEC_CORE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KEXEC_ELF                                policy<{'ppc64el': 'y'}>
+CONFIG_KEXEC_FILE                               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_KEXEC_IMAGE_VERIFY_SIG                   policy<{'arm64': 'y'}>
+CONFIG_KEXEC_JUMP                               policy<{'amd64': 'y'}>
+CONFIG_KEXEC_SIG                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_KEXEC_SIG_FORCE                          policy<{'amd64': 'n'}>
+CONFIG_KEYBOARD_ADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_ADP5520                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_ADP5588                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_ADP5589                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_APPLESPI                        policy<{'amd64': 'm'}>
+CONFIG_KEYBOARD_ATKBD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_KEYBOARD_BCM                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_CAP11XX                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_CROS_EC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_KEYBOARD_DLINK_DIR685                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_GPIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_GPIO_POLLED                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_IMX                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_KEYBOARD_IMX_SC_KEY                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_KEYBOARD_IQS62X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_LKKBD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_LM8323                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_LM8333                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_MATRIX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_MAX7359                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_MCS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_MPR121                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_MTK_PMIC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_NEWTON                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_NVEC                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_KEYBOARD_OMAP4                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_OPENCORES                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_PMIC8XXX                        policy<{'armhf': 'm'}>
+CONFIG_KEYBOARD_QT1050                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_QT1070                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_QT2160                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_SAMSUNG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_SNVS_PWRKEY                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_KEYBOARD_STMPE                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_STOWAWAY                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_SUN4I_LRADC                     policy<{'arm64': 'n'}>
+CONFIG_KEYBOARD_SUNKBD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_TC3589X                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_TCA6416                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_TCA8418                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_TEGRA                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_KEYBOARD_TM2_TOUCHKEY                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_TWL4030                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYBOARD_XTKBD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KEYS                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KEYS_REQUEST_CACHE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KEY_DH_OPERATIONS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KEY_NOTIFICATIONS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KFENCE                                   policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_KFENCE_DEFERRABLE                        policy<{'amd64': 'n', 'arm64': 'n', 's390x': 'n'}>
+CONFIG_KFENCE_NUM_OBJECTS                       policy<{'amd64': '255', 'arm64': '255', 's390x': '255'}>
+CONFIG_KFENCE_SAMPLE_INTERVAL                   policy<{'amd64': '0', 'arm64': '0', 's390x': '0'}>
+CONFIG_KFENCE_STRESS_TEST_FAULTS                policy<{'amd64': '0', 'arm64': '0', 's390x': '0'}>
+CONFIG_KGDB                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_KGDB_HONOUR_BLOCKLIST                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_KGDB_KDB                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_KGDB_LOW_LEVEL_TRAP                      policy<{'amd64': 'y'}>
+CONFIG_KGDB_TESTS                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_KHADAS_MCU_FAN_THERMAL                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_KMAP_LOCAL                               policy<{'armhf': 'y'}>
+CONFIG_KMAP_LOCAL_NON_LINEAR_PTE_ARRAY          policy<{'armhf': 'y'}>
+CONFIG_KMX61                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KPROBES                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KPROBES_ON_FTRACE                        policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KPROBES_SANITY_TEST                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_KPROBE_EVENTS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KPROBE_EVENTS_ON_NOTRACE                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_KPROBE_EVENT_GEN_TEST                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_KPSS_XCC                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_KRAITCC                                  policy<{'armhf': 'm'}>
+CONFIG_KRAIT_CLOCKS                             policy<{'armhf': 'y'}>
+CONFIG_KRAIT_L2_ACCESSORS                       policy<{'armhf': 'y'}>
+CONFIG_KRETPROBES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KS0108                                   policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KS0108_DELAY                             policy<{'amd64': '2', 'armhf': '2', 'ppc64el': '2'}>
+CONFIG_KS0108_PORT                              policy<{'amd64': '0x378', 'armhf': '0x378', 'ppc64el': '0x378'}>
+CONFIG_KS7010                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KS8842                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KS8851                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KS8851_MLL                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KSM                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KSZ884X_PCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KUNIT                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_KUSER_HELPERS                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_KVM_AMD                                  policy<{'amd64': 'm'}>
+CONFIG_KVM_AMD_SEV                              policy<{'amd64': 'y'}>
+CONFIG_KVM_ASYNC_PF                             policy<{'amd64': 'y', 's390x': 'y'}>
+CONFIG_KVM_ASYNC_PF_SYNC                        policy<{'s390x': 'y'}>
+CONFIG_KVM_BOOK3S_64                            policy<{'ppc64el': 'm'}>
+CONFIG_KVM_BOOK3S_64_HANDLER                    policy<{'ppc64el': 'y'}>
+CONFIG_KVM_BOOK3S_64_HV                         policy<{'ppc64el': 'm'}>
+CONFIG_KVM_BOOK3S_64_PR                         policy<{'ppc64el': 'm'}>
+CONFIG_KVM_BOOK3S_HANDLER                       policy<{'ppc64el': 'y'}>
+CONFIG_KVM_BOOK3S_HV_EXIT_TIMING                policy<{'ppc64el': 'n'}>
+CONFIG_KVM_BOOK3S_HV_POSSIBLE                   policy<{'ppc64el': 'y'}>
+CONFIG_KVM_BOOK3S_PR_POSSIBLE                   policy<{'ppc64el': 'y'}>
+CONFIG_KVM_COMPAT                               policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_KVM_GUEST                                policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_KVM_INTEL                                policy<{'amd64': 'm'}>
+CONFIG_KVM_MMIO                                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_KVM_MMU_AUDIT                            policy<{'amd64': 'n'}>
+CONFIG_KVM_S390_UCONTROL                        policy<{'s390x': 'n'}>
+CONFIG_KVM_VFIO                                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_KVM_WERROR                               policy<{'amd64': 'y'}>
+CONFIG_KVM_XEN                                  policy<{'amd64': 'y'}>
+CONFIG_KVM_XFER_TO_GUEST_WORK                   policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_KVM_XICS                                 policy<{'ppc64el': 'y'}>
+CONFIG_KVM_XIVE                                 policy<{'ppc64el': 'y'}>
+CONFIG_KXCJK1013                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KXSD9                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KXSD9_I2C                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_KXSD9_SPI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_L2TP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_L2TP_DEBUGFS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_L2TP_ETH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_L2TP_IP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_L2TP_V3                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LAN743X                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LANMEDIA                                 policy<{'amd64': 'm'}>
+CONFIG_LAPB                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_LAPBETHER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LATTICE_ECP3_CONFIG                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD2S                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_AMS369FG06                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_CLASS_DEVICE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_LCD_HX8357                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_ILI922X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_ILI9320                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_L4F00242T03                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_LMS283GF05                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_LMS501KF03                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_LTV350QV                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_OTM3225A                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_PLATFORM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_TDO24M                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCD_VGG2432A4                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LCS                                      policy<{'s390x': 'm'}>
+CONFIG_LDISC_AUTOLOAD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LDM_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_LDM_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_LD_DEAD_CODE_DATA_ELIMINATION            policy<{'ppc64el': 'n'}>
+CONFIG_LD_HEAD_STUB_CATCH                       policy<{'ppc64el': 'n'}>
+CONFIG_LD_IS_BFD                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LD_ORPHAN_WARN                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LD_VERSION                               policy<{'amd64': '23800', 'arm64': '23800', 'armhf': '23800', 'ppc64el': '23800', 's390x': '23800'}>
+CONFIG_LEDS_88PM860X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_AAEON                               policy<{'amd64': 'm'}>
+CONFIG_LEDS_AAT1290                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_ACER_A500                           policy<{'armhf-generic': 'm'}>
+CONFIG_LEDS_ADP5520                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_AN30259A                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_APU                                 policy<{'amd64': 'm'}>
+CONFIG_LEDS_AS3645A                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_ASIC3                               policy<{'armhf': 'y'}>
+CONFIG_LEDS_AW2013                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_BCM6328                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_BCM6358                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_BD2802                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_BLINKM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_BRIGHTNESS_HW_CHANGED               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_CLASS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_CLASS_FLASH                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_CLASS_MULTICOLOR                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_CLEVO_MAIL                          policy<{'amd64': 'm'}>
+CONFIG_LEDS_CPCAP                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_CR0014114                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_DA903X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_DA9052                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_DAC124S085                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_EL15203000                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_GPIO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_INTEL_SS4200                        policy<{'amd64': 'm'}>
+CONFIG_LEDS_IS31FL319X                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_IS31FL32XX                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_KTD2692                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3530                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3532                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3533                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM355x                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3601X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM36274                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3642                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3692X                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LM3697                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP3944                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP3952                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP50XX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP5521                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP5523                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP5562                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP55XX_COMMON                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP8501                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP8788                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LP8860                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_LT3593                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MAX77650                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MAX77693                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MAX8997                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MC13783                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MENF21BMC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MLXCPLD                             policy<{'amd64': 'm'}>
+CONFIG_LEDS_MLXREG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_MT6323                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_NIC78BX                             policy<{'amd64': 'm'}>
+CONFIG_LEDS_NS2                                 policy<{'armhf': 'm'}>
+CONFIG_LEDS_PCA9532                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_PCA9532_GPIO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_PCA955X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_PCA955X_GPIO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_PCA963X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_PM8058                              policy<{'armhf': 'm'}>
+CONFIG_LEDS_POWERNV                             policy<{'ppc64el': 'm'}>
+CONFIG_LEDS_PWM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_REGULATOR                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_RT4505                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_RT8515                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_SC27XX_BLTC                         policy<{'arm64': 'm'}>
+CONFIG_LEDS_SGM3140                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_SPI_BYTE                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_SYSCON                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_TCA6507                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TI_LMU_COMMON                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TLC591XX                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TPS6105X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGERS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_TRIGGER_ACTIVITY                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_AUDIO                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_BACKLIGHT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_CAMERA                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_CPU                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_TRIGGER_DEFAULT_ON                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_DISK                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_TRIGGER_GPIO                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_HEARTBEAT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_MTD                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_TRIGGER_NETDEV                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_ONESHOT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_PANIC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEDS_TRIGGER_PATTERN                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_TIMER                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_TRANSIENT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TRIGGER_TTY                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_TURRIS_OMNIA                        policy<{'armhf': 'm'}>
+CONFIG_LEDS_USER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_WM831X_STATUS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LEDS_WM8350                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LED_TRIGGER_PHY                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LEGACY_PTYS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LEGACY_PTY_COUNT                         policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_LEGACY_VSYSCALL_EMULATE                  policy<{'amd64': 'n'}>
+CONFIG_LEGACY_VSYSCALL_NONE                     policy<{'amd64': 'n'}>
+CONFIG_LEGACY_VSYSCALL_XONLY                    policy<{'amd64': 'y'}>
+CONFIG_LG_LAPTOP                                policy<{'amd64': 'm'}>
+CONFIG_LIB80211                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIB80211_CRYPT_CCMP                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIB80211_CRYPT_TKIP                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIB80211_CRYPT_WEP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIB80211_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_LIBCRC32C                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LIBERTAS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBERTAS_CS                              policy<{'amd64': 'm'}>
+CONFIG_LIBERTAS_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_LIBERTAS_MESH                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LIBERTAS_SDIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBERTAS_SPI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBERTAS_THINFIRM                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBERTAS_THINFIRM_DEBUG                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_LIBERTAS_THINFIRM_USB                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBERTAS_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBFC                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LIBFCOE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LIBFDT                                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LIBIPW                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIBIPW_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_LIBNVDIMM                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_LIB_MEMNEQ                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LIDAR_LITE_V2                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LINEAR_RANGES                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LIQUIDIO                                 policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_LIQUIDIO_VF                              policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_LIRC                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LITEX                                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LITEX_LITEETH                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LITEX_SOC_CONTROLLER                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LIVEPATCH                                policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LKDTM                                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LLC                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LLC2                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_LLD_VERSION                              policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_LMK04832                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LMP91000                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LOAD_IPL_KEYS                            policy<{'s390x': 'y'}>
+CONFIG_LOAD_UEFI_KEYS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_LOCALVERSION                             policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_LOCKD                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LOCKDEP_SUPPORT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LOCKD_V4                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LOCKUP_DETECTOR                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LOCK_DEBUGGING_SUPPORT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LOCK_DOWN_IN_SECURE_BOOT                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LOCK_DOWN_KERNEL_FORCE_CONFIDENTIALITY   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOCK_DOWN_KERNEL_FORCE_INTEGRITY         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOCK_DOWN_KERNEL_FORCE_NONE              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LOCK_EVENT_COUNTS                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOCK_SPIN_ON_OWNER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LOCK_STAT                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOCK_TORTURE_TEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOGIG940_FF                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LOGIRUMBLEPAD2_FF                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LOGITECH_FF                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LOGIWHEELS_FF                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_LOGO                                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_LOG_BUF_SHIFT                            policy<{'amd64': '18', 'arm64': '18', 'armhf': '17', 'ppc64el': '18', 's390x': '18'}>
+CONFIG_LOG_CPU_MAX_BUF_SHIFT                    policy<{'amd64': '12', 'arm64': '12', 'armhf': '12', 'ppc64el': '12', 's390x': '12'}>
+CONFIG_LOOPBACK_TARGET                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LP8788_ADC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LPARCFG                                  policy<{'ppc64el': 'y'}>
+CONFIG_LPC_ICH                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_LPC_SCH                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_LP_CONSOLE                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_LRU_CACHE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LSI_ET1011C_PHY                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LSM                                      policy<{'amd64': '"landlock,lockdown,yama,integrity,apparmor"', 'arm64': '"landlock,lockdown,yama,integrity,apparmor"', 'armhf': '"landlock,lockdown,yama,integrity,apparmor"', 'ppc64el': '"landlock,lockdown,yama,integrity,apparmor"', 's390x': '"landlock,lockdown,yama,integrity,apparmor"'}>
+CONFIG_LSM_MMAP_MIN_ADDR                        policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_LS_EXTIRQ                                policy<{'arm64': 'y'}>
+CONFIG_LS_SCFG_MSI                              policy<{'arm64': 'y'}>
+CONFIG_LTC1660                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTC2471                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTC2485                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTC2496                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTC2497                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTC2632                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTC2983                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTE_GDM724X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LTO_NONE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LTR501                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LV0104CS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_LWTUNNEL                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LWTUNNEL_BPF                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LXT_PHY                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LZ4HC_COMPRESS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LZ4_COMPRESS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_LZ4_DECOMPRESS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LZO_COMPRESS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_LZO_DECOMPRESS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_M62332                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAC80211                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAC80211_DEBUGFS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_DEBUG_MENU                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MAC80211_HAS_RC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_HWSIM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAC80211_LEDS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_MESH                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_MESSAGE_TRACING                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_RC_DEFAULT                      policy<{'amd64': '"minstrel_ht"', 'arm64': '"minstrel_ht"', 'armhf': '"minstrel_ht"', 'ppc64el': '"minstrel_ht"'}>
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_RC_MINSTREL                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MAC80211_STA_HASH_MAX_SIZE               policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_MAC802154                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MACB                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MACB_PCI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MACB_USE_HWSTAMP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MACHZ_WDT                                policy<{'amd64': 'm'}>
+CONFIG_MACH_ARMADA_370                          policy<{'armhf': 'y'}>
+CONFIG_MACH_ARMADA_375                          policy<{'armhf': 'y'}>
+CONFIG_MACH_ARMADA_38X                          policy<{'armhf': 'y'}>
+CONFIG_MACH_ARMADA_39X                          policy<{'armhf': 'y'}>
+CONFIG_MACH_ARMADA_XP                           policy<{'armhf': 'y'}>
+CONFIG_MACH_ARTPEC6                             policy<{'armhf': 'n'}>
+CONFIG_MACH_ASPEED_G6                           policy<{'armhf': 'y'}>
+CONFIG_MACH_BERLIN_BG2                          policy<{'armhf': 'y'}>
+CONFIG_MACH_BERLIN_BG2CD                        policy<{'armhf': 'y'}>
+CONFIG_MACH_BERLIN_BG2Q                         policy<{'armhf': 'y'}>
+CONFIG_MACH_DOVE                                policy<{'armhf': 'y'}>
+CONFIG_MACH_INFINITY                            policy<{'armhf': 'y'}>
+CONFIG_MACH_MERCURY                             policy<{'armhf': 'y'}>
+CONFIG_MACH_MESON6                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MESON8                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT2701                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT6589                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT6592                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT7623                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT7629                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT8127                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MT8135                              policy<{'armhf': 'y'}>
+CONFIG_MACH_MVEBU_ANY                           policy<{'armhf': 'y'}>
+CONFIG_MACH_MVEBU_V7                            policy<{'armhf': 'y'}>
+CONFIG_MACH_OMAP_GENERIC                        policy<{'armhf': 'y'}>
+CONFIG_MACINTOSH_DRIVERS                        policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_MACSEC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MACVLAN                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MACVTAP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MAC_EMUMOUSEBTN                          policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_MAC_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MADERA_IRQ                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAG3110                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAGIC_SYSRQ                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MAGIC_SYSRQ_DEFAULT_ENABLE               policy<{'amd64': '0x01b6', 'arm64': '0x01b6', 'armhf': '0x01b6', 'ppc64el': '0x01b6', 's390x': '0x01b6'}>
+CONFIG_MAGIC_SYSRQ_SERIAL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MAGIC_SYSRQ_SERIAL_SEQUENCE              policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_MAILBOX                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MAILBOX_TEST                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MANAGER_SBS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MANTIS_CORE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAPPING_DIRTY_HELPERS                    policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_MARCH_Z10                                policy<{'s390x': 'n'}>
+CONFIG_MARCH_Z13                                policy<{'s390x': 'y'}>
+CONFIG_MARCH_Z14                                policy<{'s390x': 'n'}>
+CONFIG_MARCH_Z15                                policy<{'s390x': 'n'}>
+CONFIG_MARCH_Z15_TUNE                           policy<{'s390x': 'y'}>
+CONFIG_MARCH_Z196                               policy<{'s390x': 'n'}>
+CONFIG_MARCH_Z900                               policy<{'s390x': 'n'}>
+CONFIG_MARCH_Z990                               policy<{'s390x': 'n'}>
+CONFIG_MARCH_Z9_109                             policy<{'s390x': 'n'}>
+CONFIG_MARCH_ZEC12                              policy<{'s390x': 'n'}>
+CONFIG_MARVELL_10G_PHY                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MARVELL_88X2222_PHY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MARVELL_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MATOM                                    policy<{'amd64': 'n'}>
+CONFIG_MAX1027                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX11100                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX1118                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX1241                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX1363                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX30100                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX30102                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX31856                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX44000                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX44009                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX517                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX5432                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX5481                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX5487                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX5821                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX63XX_WATCHDOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MAX77620_THERMAL                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX77620_WATCHDOG                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX8925_POWER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAX9611                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAXIM_THERMOCOUPLE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MAXLINEAR_GPHY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MAXSMP                                   policy<{'amd64': 'y'}>
+CONFIG_MAX_PHYSMEM_BITS                         policy<{'s390x': '46'}>
+CONFIG_MB1232                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MC3230                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCB                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MCB_LPC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCB_PCI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCORE2                                   policy<{'amd64': 'n'}>
+CONFIG_MCP320X                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP3422                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP3911                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP4018                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP41010                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP4131                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP4531                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP4725                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCP4922                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MCPM                                     policy<{'armhf': 'y'}>
+CONFIG_MCPM_QUAD_CLUSTER                        policy<{'armhf': 'y'}>
+CONFIG_MCTP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MD                                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MDIO                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_ASPEED                              policy<{'armhf': 'm'}>
+CONFIG_MDIO_BCM_IPROC                           policy<{'arm64': 'n'}>
+CONFIG_MDIO_BCM_UNIMAC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MDIO_BITBANG                             policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MDIO_BUS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_MDIO_BUS_MUX                             policy<{'arm64': 'y', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_BUS_MUX_BCM_IPROC                   policy<{'arm64': 'y'}>
+CONFIG_MDIO_BUS_MUX_GPIO                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_BUS_MUX_MESON_G12A                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MDIO_BUS_MUX_MMIOREG                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_BUS_MUX_MULTIPLEXER                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_CAVIUM                              policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_DEVICE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MDIO_DEVRES                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_MDIO_GPIO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_HISI_FEMAC                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_I2C                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MDIO_IPQ4019                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_IPQ8064                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_MSCC_MIIM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MDIO_MVUSB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_OCTEON                              policy<{'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_MDIO_SUN4I                               policy<{'arm64': 'n'}>
+CONFIG_MDIO_THUNDER                             policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MDIO_XGENE                               policy<{'arm64': 'm'}>
+CONFIG_MDM_GCC_9607                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MDM_GCC_9615                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MDM_LCC_9615                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MD_AUTODETECT                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MD_CLUSTER                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MD_FAULTY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MD_LINEAR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MD_MULTIPATH                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'y'}>
+CONFIG_MD_RAID0                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MD_RAID1                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MD_RAID10                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MD_RAID456                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MEDIATEK_GE_PHY                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MEDIATEK_MT6360_ADC                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIATEK_MT6577_AUXADC                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MEDIATEK_WATCHDOG                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MEDIA_ALTERA_CI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_ANALOG_TV_SUPPORT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_ATTACH                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_CAMERA_SUPPORT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_CEC_RC                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_CEC_SUPPORT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MEDIA_COMMON_OPTIONS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_CONTROLLER                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_CONTROLLER_DVB                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_CONTROLLER_REQUEST_API             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_DIGITAL_TV_SUPPORT                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_PCI_SUPPORT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_PLATFORM_SUPPORT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_RADIO_SUPPORT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_SDR_SUPPORT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_SUBDRV_AUTOSELECT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_SUPPORT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MEDIA_SUPPORT_FILTER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_TEST_SUPPORT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEDIA_TUNER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_E4000                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_FC0011                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_FC0012                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_FC0013                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_FC2580                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_IT913X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_M88RS6000T                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MAX2165                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MC44S803                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MSI001                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MT2060                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MT2063                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MT20XX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MT2131                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MT2266                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MXL301RF                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MXL5005S                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_MXL5007T                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_QM1D1B0004                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_QM1D1C0042                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_QT1010                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_R820T                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_SI2157                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_SIMPLE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA18212                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA18218                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA18250                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA18271                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA827X                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA8290                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TDA9887                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TEA5761                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TEA5767                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_TUA9001                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_XC2028                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_XC4000                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_TUNER_XC5000                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEDIA_USB_SUPPORT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEGARAID_LEGACY                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MEGARAID_MAILBOX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEGARAID_MM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEGARAID_NEWGEN                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MEGARAID_SAS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MELLANOX_PLATFORM                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MEMBARRIER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMCG                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMCG_KMEM                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMCG_SWAP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMFD_CREATE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMORY                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MEMORY_BALLOON                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMORY_FAILURE                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_MEMORY_HOTPLUG                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMORY_HOTPLUG_SPARSE                    policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMORY_HOTREMOVE                         policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMORY_ISOLATION                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MEMORY_NOTIFIER_ERROR_INJECT             policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MEMREGION                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y'}>
+CONFIG_MEMSTICK                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MEMSTICK_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MEMSTICK_JMICRON_38X                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEMSTICK_R592                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEMSTICK_REALTEK_PCI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEMSTICK_REALTEK_USB                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEMSTICK_TIFM_MS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEMSTICK_UNSAFE_RESUME                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MEMTEST                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MEM_SOFT_DIRTY                           policy<{'amd64': 'y', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_MENF21BMC_WATCHDOG                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MENZ069_WATCHDOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MEN_A21_WDT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MEN_Z188_ADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MERAKI_MX100                             policy<{'amd64': 'm'}>
+CONFIG_MESON6_TIMER                             policy<{'armhf': 'y'}>
+CONFIG_MESON_CANVAS                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MESON_CLK_MEASURE                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MESON_EE_PM_DOMAINS                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MESON_EFUSE                              policy<{'arm64-generic': 'm', 'arm64-lowlatency': 'm'}>
+CONFIG_MESON_GXBB_WATCHDOG                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MESON_GXL_PHY                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MESON_GX_PM_DOMAINS                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MESON_GX_SOCINFO                         policy<{'arm64': 'y'}>
+CONFIG_MESON_IRQ_GPIO                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MESON_MX_EFUSE                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MESON_MX_SOCINFO                         policy<{'armhf': 'y'}>
+CONFIG_MESON_SARADC                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MESON_SECURE_PM_DOMAINS                  policy<{'arm64-generic': 'y', 'arm64-lowlatency': 'y'}>
+CONFIG_MESON_SM                                 policy<{'arm64-generic': 'y', 'arm64-lowlatency': 'y'}>
+CONFIG_MESON_WATCHDOG                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT                 policy<{'amd64': '4', 'arm64': '4', 'armhf': '4', 'ppc64el': '4', 's390x': '4'}>
+CONFIG_MFD_88PM800                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_88PM805                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_88PM860X                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_AAEON                                policy<{'amd64': 'm'}>
+CONFIG_MFD_AAT2870_CORE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_AC100                                policy<{'arm64': 'n'}>
+CONFIG_MFD_ACER_A500_EC                         policy<{'armhf-generic': 'm'}>
+CONFIG_MFD_ACT8945A                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ALTERA_A10SR                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MFD_ALTERA_SYSMGR                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MFD_ARIZONA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ARIZONA_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_ARIZONA_SPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_AS3711                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_AS3722                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_ASIC3                                policy<{'armhf': 'y'}>
+CONFIG_MFD_ATC260X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ATC260X_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_ATMEL_FLEXCOM                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ATMEL_HLCDC                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_AXP20X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_AXP20X_I2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_AXP20X_RSB                           policy<{'arm64': 'm'}>
+CONFIG_MFD_BCM590XX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_BD9571MWV                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_CORE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_CPCAP                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_CROS_EC_DEV                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MFD_CS47L15                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_CS47L24                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_CS47L35                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_CS47L85                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_CS47L90                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_CS47L92                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_DA9052_I2C                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_DA9052_SPI                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_DA9055                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_DA9062                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_DA9063                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MFD_DA9150                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_DLN2                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_EXYNOS_LPASS                         policy<{'armhf': 'm'}>
+CONFIG_MFD_GATEWORKS_GSC                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_HI6421_PMIC                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_HI6421_SPMI                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_HI655X_PMIC                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MFD_INTEL_LPSS                           policy<{'amd64': 'm'}>
+CONFIG_MFD_INTEL_LPSS_ACPI                      policy<{'amd64': 'm'}>
+CONFIG_MFD_INTEL_LPSS_PCI                       policy<{'amd64': 'm'}>
+CONFIG_MFD_INTEL_M10_BMC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_INTEL_PMC_BXT                        policy<{'amd64': 'm'}>
+CONFIG_MFD_INTEL_PMT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_INTEL_QUARK_I2C_GPIO                 policy<{'amd64': 'm'}>
+CONFIG_MFD_IQS62X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_JANZ_CMODIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_KEMPLD                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_KHADAS_MCU                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MFD_LJCA                                 policy<{'amd64': 'm', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MFD_LM3533                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_LOCHNAGAR                            policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_LP3943                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_LP8788                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MADERA                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_MADERA_I2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_MADERA_SPI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_MAX14577                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MFD_MAX77620                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MAX77650                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_MAX77686                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MAX77693                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MFD_MAX77843                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MAX8907                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_MAX8925                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MAX8997                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MAX8998                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_MC13XXX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_MC13XXX_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_MC13XXX_SPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_MENF21BMC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_MP2629                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_MT6360                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_MT6397                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_NTXEC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_NVEC                                 policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_MFD_OMAP_USB_HOST                        policy<{'armhf': 'y'}>
+CONFIG_MFD_PALMAS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_PCF50633                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_PM8XXX                               policy<{'armhf': 'm'}>
+CONFIG_MFD_QCOM_PM8008                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_QCOM_RPM                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MFD_RC5T583                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_RDC321X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_RETU                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_RK808                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_RN5T618                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ROHM_BD70528                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ROHM_BD71828                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ROHM_BD718XX                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_ROHM_BD957XMUF                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_RSMU_I2C                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_RSMU_SPI                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_RT4831                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_RT5033                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_SC27XX_PMIC                          policy<{'arm64': 'm'}>
+CONFIG_MFD_SEC_CORE                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_SI476X_CORE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_SIMPLE_MFD_I2C                       policy<{'arm64': 'm'}>
+CONFIG_MFD_SKY81452                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_SL28CPLD                             policy<{'arm64': 'm'}>
+CONFIG_MFD_SM501_GPIO                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_SPMI_PMIC                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MFD_STMFX                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_STMPE                                policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_STPMIC1                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_SUN4I_GPADC                          policy<{'arm64': 'm'}>
+CONFIG_MFD_SUN6I_PRCM                           policy<{'arm64': 'y'}>
+CONFIG_MFD_SYSCON                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MFD_T7L66XB                              policy<{'armhf': 'y'}>
+CONFIG_MFD_TC3589X                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TC6387XB                             policy<{'armhf': 'y'}>
+CONFIG_MFD_TC6393XB                             policy<{'armhf': 'y'}>
+CONFIG_MFD_TI_AM335X_TSCADC                     policy<{'amd64': '-', 'arm64': 'm', 'armhf': 'm', 'ppc64el': '-', 's390x': '-'}>
+CONFIG_MFD_TI_LMU                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_TI_LP873X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_TI_LP87565                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_TMIO                                 policy<{'armhf': 'y'}>
+CONFIG_MFD_TPS65086                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_TPS65090                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TPS65218                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_TPS6586X                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TPS65910                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TPS65912                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TPS65912_I2C                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MFD_TPS65912_SPI                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TPS80031                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_TQMX86                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_TWL4030_AUDIO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_VEXPRESS_SYSREG                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MFD_VIPERBOARD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MFD_VX855                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_WCD934X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_WL1273_CORE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_WM5102                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM5110                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM831X                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM831X_I2C                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM831X_SPI                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM8350                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM8350_I2C                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM8400                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM8994                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MFD_WM8997                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MFD_WM8998                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MHI_BUS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MHI_BUS_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MHI_BUS_PCI_GENERIC                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MHI_NET                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MHI_WWAN_CTRL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MHI_WWAN_MBIM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MHP_MEMMAP_ON_MEMORY                     policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_MICREL_KS8995MA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MICREL_PHY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MICROCHIP_PHY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MICROCHIP_PIT64B                         policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MICROCHIP_T1_PHY                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MICROCHIP_TCB_CAPTURE                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MICROCODE                                policy<{'amd64': 'y'}>
+CONFIG_MICROCODE_AMD                            policy<{'amd64': 'y'}>
+CONFIG_MICROCODE_INTEL                          policy<{'amd64': 'y'}>
+CONFIG_MICROCODE_LATE_LOADING                   policy<{'amd64': 'n'}>
+CONFIG_MICROSEMI_PHY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MICROSOFT_MANA                           policy<{'amd64': 'm'}>
+CONFIG_MIGHT_HAVE_CACHE_L2X0                    policy<{'armhf': 'y'}>
+CONFIG_MIGRATION                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MII                                      policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MILBEAUT_HDMAC                           policy<{'armhf': 'm'}>
+CONFIG_MILBEAUT_TIMER                           policy<{'armhf': 'y'}>
+CONFIG_MILBEAUT_XDMAC                           policy<{'armhf': 'm'}>
+CONFIG_MINIX_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MINIX_SUBPARTITION                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MIPI_I3C_HCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISC_ALCOR_PCI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MISC_FILESYSTEMS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MISC_RTSX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISC_RTSX_PCI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MISC_RTSX_USB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_AVMFRITZ                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_DSP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_HDLC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_HFCMULTI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_HFCPCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_HFCUSB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_INFINEON                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_IPAC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_ISAR                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_L1OIP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_NETJET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_SPEEDFAX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MISDN_W6692                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY          policy<{'arm64': 'y'}>
+CONFIG_MITIGATION_RFDS                          policy<{'amd64': 'y'}>
+CONFIG_MITIGATION_SPECTRE_BHI                   policy<{'amd64': 'y'}>
+CONFIG_MK8                                      policy<{'amd64': 'n'}>
+CONFIG_MKISS                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MLX4_CORE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLX4_CORE_GEN2                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX4_DEBUG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX4_EN                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLX4_EN_DCB                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX4_INFINIBAND                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLX5_ACCEL                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_BRIDGE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_CLS_ACT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_CORE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLX5_CORE_EN                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_CORE_EN_DCB                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_CORE_IPOIB                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_EN_ARFS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_EN_IPSEC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_EN_RXNFC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_EN_TLS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_ESWITCH                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_FPGA                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_FPGA_IPSEC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_FPGA_TLS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_INFINIBAND                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLX5_IPSEC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_MPFS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_SF                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MLX5_SF_MANAGER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MLX5_SW_STEERING                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_TC_CT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_TC_SAMPLE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_TLS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX5_VDPA                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MLX5_VDPA_NET                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MLX90614                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MLX90632                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MLXBF_BOOTCTL                            policy<{'arm64': 'm'}>
+CONFIG_MLXBF_GIGE                               policy<{'arm64': 'm'}>
+CONFIG_MLXBF_PMC                                policy<{'arm64': 'm'}>
+CONFIG_MLXBF_TMFIFO                             policy<{'arm64': 'm'}>
+CONFIG_MLXFW                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLXREG_HOTPLUG                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MLXREG_IO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MLXSW_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLXSW_CORE_HWMON                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MLXSW_CORE_THERMAL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MLXSW_I2C                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MLXSW_MINIMAL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MLXSW_PCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLXSW_SPECTRUM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MLXSW_SPECTRUM_DCB                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MLX_PLATFORM                             policy<{'amd64': 'm'}>
+CONFIG_MLX_WDT                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMA7455                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA7455_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA7455_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA7660                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA8452                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA9551                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA9551_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMA9553                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_MMC35240                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMCONF_FAM10H                            policy<{'amd64': 'y'}>
+CONFIG_MMC_ALCOR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_ARMMMCI                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MMC_BCM2835                              policy<{'arm64': 'm'}>
+CONFIG_MMC_BLOCK_MINORS                         policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8'}>
+CONFIG_MMC_CAVIUM_THUNDERX                      policy<{'arm64': 'm'}>
+CONFIG_MMC_CB710                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_CQHCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'y', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_CRYPTO                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MMC_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MMC_DW                                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_BLUEFIELD                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_EXYNOS                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_HI3798CV200                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_K3                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_PCI                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_PLTFM                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_DW_ROCKCHIP                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_HSQ                                  policy<{'amd64': 'n', 'arm64': 'm', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MMC_MESON_GX                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_MESON_MX_SDHC                        policy<{'armhf': 'm'}>
+CONFIG_MMC_MESON_MX_SDIO                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_MTK                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_MVSDIO                               policy<{'armhf': 'm'}>
+CONFIG_MMC_MXC                                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_MMC_OMAP                                 policy<{'armhf': 'm'}>
+CONFIG_MMC_OWL                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_QCOM_DML                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MMC_REALTEK_PCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_REALTEK_USB                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_RICOH_MMC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MMC_SDHCI_ACPI                           policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_MMC_SDHCI_AM654                          policy<{'arm64': 'm', 'armhf': '-', 'ppc64el': '-'}>
+CONFIG_MMC_SDHCI_BIG_ENDIAN_32BIT_BYTE_SWAPPER  policy<{'ppc64el': 'y'}>
+CONFIG_MMC_SDHCI_BRCMSTB                        policy<{'arm64': 'm'}>
+CONFIG_MMC_SDHCI_CADENCE                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_DOVE                           policy<{'armhf': 'm'}>
+CONFIG_MMC_SDHCI_ESDHC_IMX                      policy<{'arm64': 'm', 'armhf-generic': 'y'}>
+CONFIG_MMC_SDHCI_EXTERNAL_DMA                   policy<{'arm64': '-', 'armhf': 'y', 'ppc64el': '-'}>
+CONFIG_MMC_SDHCI_F_SDH30                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_IO_ACCESSORS                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MMC_SDHCI_IPROC                          policy<{'arm64': 'm'}>
+CONFIG_MMC_SDHCI_MILBEAUT                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_MSM                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_SDHCI_OF_ARASAN                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_OF_ASPEED                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_OF_AT91                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_OF_DWCMSHC                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_OF_ESDHC                       policy<{'arm64': 'm', 'armhf-generic': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_OF_HLWD                        policy<{'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_OF_SPARX5                      policy<{'arm64': 'm'}>
+CONFIG_MMC_SDHCI_OMAP                           policy<{'arm64': '-', 'armhf': 'm', 'ppc64el': '-'}>
+CONFIG_MMC_SDHCI_PCI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHCI_PXAV3                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_SDHCI_S3C                            policy<{'armhf': 'm'}>
+CONFIG_MMC_SDHCI_S3C_DMA                        policy<{'armhf': 'y'}>
+CONFIG_MMC_SDHCI_SPRD                           policy<{'arm64': 'm'}>
+CONFIG_MMC_SDHCI_TEGRA                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_MMC_SDHCI_XENON                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_SDHI                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_SDHI_INTERNAL_DMAC                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_SDHI_SYS_DMAC                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_SDRICOH_CS                           policy<{'amd64': 'm'}>
+CONFIG_MMC_SH_MMCIF                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_SPI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_STM32_SDMMC                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MMC_SUNXI                                policy<{'arm64': 'm'}>
+CONFIG_MMC_TEST                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MMC_TIFM_SD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_TMIO                                 policy<{'armhf': 'm'}>
+CONFIG_MMC_TMIO_CORE                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MMC_TOSHIBA_PCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_UNIPHIER                             policy<{'armhf': 'm'}>
+CONFIG_MMC_USDHI6ROL0                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_USHC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_VIA_SDMMC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_VUB300                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MMC_WBSD                                 policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_MMIOTRACE                                policy<{'amd64': 'y'}>
+CONFIG_MMIOTRACE_TEST                           policy<{'amd64': 'n'}>
+CONFIG_MMIOWB                                   policy<{'ppc64el': 'y'}>
+CONFIG_MMU                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MMU_GATHER_NO_GATHER                     policy<{'s390x': 'y'}>
+CONFIG_MMU_GATHER_PAGE_SIZE                     policy<{'ppc64el': 'y'}>
+CONFIG_MMU_GATHER_RCU_TABLE_FREE                policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MMU_GATHER_TABLE_FREE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MMU_NOTIFIER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODPROBE_PATH                            policy<{'amd64': '"/sbin/modprobe"', 'arm64': '"/sbin/modprobe"', 'armhf': '"/sbin/modprobe"', 'ppc64el': '"/sbin/modprobe"', 's390x': '"/sbin/modprobe"'}>
+CONFIG_MODULES                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULES_TREE_LOOKUP                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULES_USE_ELF_REL                      policy<{'armhf': 'y'}>
+CONFIG_MODULES_USE_ELF_RELA                     policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_COMPRESS_GZIP                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_COMPRESS_NONE                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_COMPRESS_XZ                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_COMPRESS_ZSTD                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_FORCE_LOAD                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_FORCE_UNLOAD                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_REL_CRCS                          policy<{'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_SIG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_SIG_ALL                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_SIG_FORCE                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_SIG_FORMAT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_SIG_HASH                          policy<{'amd64': '"sha512"', 'arm64': '"sha512"', 'armhf': '"sha512"', 'ppc64el': '"sha512"', 's390x': '"sha512"'}>
+CONFIG_MODULE_SIG_KEY                           policy<{'amd64': '"certs/signing_key.pem"', 'arm64': '"certs/signing_key.pem"', 'armhf': '"certs/signing_key.pem"', 'ppc64el': '"certs/signing_key.pem"', 's390x': '"certs/signing_key.pem"'}>
+CONFIG_MODULE_SIG_KEY_TYPE_ECDSA                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_SIG_KEY_TYPE_RSA                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_SIG_SHA1                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_SIG_SHA224                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_SIG_SHA256                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_SIG_SHA384                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_MODULE_SIG_SHA512                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_SRCVERSION_ALL                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MODULE_UNLOAD                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MONREADER                                policy<{'s390x': 'm'}>
+CONFIG_MONWRITER                                policy<{'s390x': 'm'}>
+CONFIG_MOST                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MOST_CDEV                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_COMPONENTS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_DIM2                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_I2C                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_NET                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_SND                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_USB_HDM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOST_VIDEO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOTORCOMM_PHY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_MOUSE_APPLETOUCH                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_BCM5974                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_CYAPA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_ELAN_I2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_ELAN_I2C_I2C                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_ELAN_I2C_SMBUS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_GPIO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_PS2                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_PS2_ALPS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_BYD                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_CYPRESS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_ELANTECH                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_ELANTECH_SMBUS                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_FOCALTECH                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_LIFEBOOK                       policy<{'amd64': 'y'}>
+CONFIG_MOUSE_PS2_LOGIPS2PP                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_SENTELIC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_SMBUS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_SYNAPTICS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_TOUCHKIT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_TRACKPOINT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MOUSE_PS2_VMMOUSE                        policy<{'amd64': 'y'}>
+CONFIG_MOUSE_SERIAL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_SYNAPTICS_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_SYNAPTICS_USB                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOUSE_VSXXXAA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOXA_INTELLIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOXA_SMARTIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MOXTET                                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MP2629_ADC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MPIC                                     policy<{'ppc64el': 'y'}>
+CONFIG_MPIC_MSGR                                policy<{'ppc64el': 'n'}>
+CONFIG_MPILIB                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MPL115                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MPL115_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MPL115_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MPL3115                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MPLS                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MPLS_IPTUNNEL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MPLS_ROUTING                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MPROFILE_KERNEL                          policy<{'ppc64el': 'y'}>
+CONFIG_MPSC                                     policy<{'amd64': 'n'}>
+CONFIG_MPTCP                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MPTCP_IPV6                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MPU3050                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MPU3050_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MQ_IOSCHED_DEADLINE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MQ_IOSCHED_KYBER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MRP                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MS5611                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MS5611_I2C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MS5611_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MS5637                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MSC313E_WATCHDOG                         policy<{'armhf': 'm'}>
+CONFIG_MSCC_OCELOT_SWITCH                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MSCC_OCELOT_SWITCH_LIB                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MSDOS_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_MSDOS_PARTITION                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MSI_BITMAP_SELFTEST                      policy<{'ppc64el': 'n'}>
+CONFIG_MSI_LAPTOP                               policy<{'amd64': 'm'}>
+CONFIG_MSI_WMI                                  policy<{'amd64': 'm'}>
+CONFIG_MSM_GCC_8660                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8916                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8939                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8953                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8960                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8974                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8994                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8996                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GCC_8998                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_GPUCC_8998                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_IOMMU                                policy<{'armhf': 'n'}>
+CONFIG_MSM_LCC_8960                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_MMCC_8960                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_MMCC_8974                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_MMCC_8994                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_MMCC_8996                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSM_MMCC_8998                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MSPRO_BLOCK                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MSTAR_MSC313_MPLL                        policy<{'armhf': 'y'}>
+CONFIG_MST_IRQ                                  policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MS_BLOCK                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7601U                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7603E                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7615E                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7615_COMMON                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7622_WMAC                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MT7663S                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7663U                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7663_USB_SDIO_COMMON                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76_CONNAC_LIB                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76_CORE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76_LEDS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MT76_SDIO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76_USB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x02_LIB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x02_USB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x0E                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x0U                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x0_COMMON                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x2E                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x2U                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT76x2_COMMON                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7915E                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MT7921E                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTDRAM_ERASE_SIZE                        policy<{'amd64': '128', 'arm64': '128', 'armhf': '128', 'ppc64el': '128'}>
+CONFIG_MTDRAM_TOTAL_SIZE                        policy<{'amd64': '4096', 'arm64': '4096', 'armhf': '4096', 'ppc64el': '4096'}>
+CONFIG_MTD_ABSENT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_AFS_PARTS                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_AMD76XROM                            policy<{'amd64': 'm'}>
+CONFIG_MTD_AR7_PARTS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_BCM47XXSFLASH                        policy<{'armhf': 'm'}>
+CONFIG_MTD_BLKDEVS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MTD_BLOCK2MTD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_BLOCK_RO                             policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_CFI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_CFI_ADV_OPTIONS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_CFI_AMDSTD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_CFI_I1                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_CFI_I2                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_CFI_INTELEXT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_CFI_STAA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_CFI_UTIL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_CK804XROM                            policy<{'amd64': 'm'}>
+CONFIG_MTD_CMDLINE_PARTS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MTD_COMPLEX_MAPPINGS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_DATAFLASH                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_DATAFLASH_OTP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_DATAFLASH_WRITE_VERIFY               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_ESB2ROM                              policy<{'amd64': 'm'}>
+CONFIG_MTD_GEN_PROBE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_HYPERBUS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_ICHXROM                              policy<{'amd64': 'm'}>
+CONFIG_MTD_IMPA7                                policy<{'armhf': 'm'}>
+CONFIG_MTD_INTEL_VR_NOR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_JEDECPROBE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_L440GX                               policy<{'amd64': 'm'}>
+CONFIG_MTD_LPDDR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_LPDDR2_NVM                           policy<{'armhf': 'm'}>
+CONFIG_MTD_MAP_BANK_WIDTH_1                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_MAP_BANK_WIDTH_2                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_MAP_BANK_WIDTH_4                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_MCHP23K256                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_MCHP48L640                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_MTDRAM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_ARASAN                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_BRCMNAND                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_CADENCE                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_CAFE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_CORE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_DENALI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_DENALI_DT                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_DENALI_PCI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_DISKONCHIP                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS        policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_NAND_ECC                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_NAND_ECC_SW_BCH                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_NAND_ECC_SW_HAMMING                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_NAND_ECC_SW_HAMMING_SMC              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_NAND_FSL_IFC                         policy<{'arm64': 'm'}>
+CONFIG_MTD_NAND_GPIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_GPMI_NAND                       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_MTD_NAND_HISI504                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_INTEL_LGM                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_MARVELL                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_MESON                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_MTK                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_MXC                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_MTD_NAND_MXIC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_NANDSIM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_OMAP_BCH_BUILD                  policy<{'armhf': 'y'}>
+CONFIG_MTD_NAND_ORION                           policy<{'armhf': 'm'}>
+CONFIG_MTD_NAND_PL35X                           policy<{'armhf': 'm'}>
+CONFIG_MTD_NAND_PLATFORM                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_QCOM                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_RICOH                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_NAND_ROCKCHIP                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_NAND_SUNXI                           policy<{'arm64': 'n'}>
+CONFIG_MTD_NAND_TEGRA                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_MTD_NAND_TMIO                            policy<{'armhf': 'm'}>
+CONFIG_MTD_NAND_VF610_NFC                       policy<{'armhf-generic': 'n'}>
+CONFIG_MTD_NETtel                               policy<{'amd64': 'm'}>
+CONFIG_MTD_OF_PARTS_BCM4908                     policy<{'arm64': 'y'}>
+CONFIG_MTD_OF_PARTS_LINKSYS_NS                  policy<{'arm64': 'y'}>
+CONFIG_MTD_ONENAND                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_ONENAND_2X_PROGRAM                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_ONENAND_GENERIC                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_ONENAND_OMAP2                        policy<{'armhf-generic': 'm'}>
+CONFIG_MTD_ONENAND_OTP                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_OOPS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_PARSER_TRX                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_PARTITIONED_MASTER                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_PCI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_PCMCIA                               policy<{'amd64': 'm'}>
+CONFIG_MTD_PCMCIA_ANONYMOUS                     policy<{'amd64': 'n'}>
+CONFIG_MTD_PHRAM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_PHYSMAP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_PHYSMAP_COMPAT                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_PHYSMAP_GEMINI                       policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n'}>
+CONFIG_MTD_PHYSMAP_GPIO_ADDR                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_PHYSMAP_IXP4XX                       policy<{'armhf': 'y'}>
+CONFIG_MTD_PHYSMAP_OF                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_PHYSMAP_VERSATILE                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'n'}>
+CONFIG_MTD_PLATRAM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_PMC551                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_PMC551_BUGFIX                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_PMC551_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_POWERNV_FLASH                        policy<{'ppc64el': 'm'}>
+CONFIG_MTD_PSTORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_QCOMSMEM_PARTS                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTD_QINFO_PROBE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_RAM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK              policy<{'amd64': '-1', 'arm64': '-1', 'armhf': '-1', 'ppc64el': '-1'}>
+CONFIG_MTD_REDBOOT_PARTS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_REDBOOT_PARTS_READONLY               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_ROM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_SBC_GXX                              policy<{'amd64': 'm'}>
+CONFIG_MTD_SCB2_FLASH                           policy<{'amd64': 'm'}>
+CONFIG_MTD_SHARPSL_PARTS                        policy<{'armhf': 'm'}>
+CONFIG_MTD_SLRAM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_SM_COMMON                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_SPI_NAND                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_SPI_NOR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_SPI_NOR_SWP_DISABLE                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_SPI_NOR_SWP_DISABLE_ON_VOLATILE      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_SPI_NOR_SWP_KEEP                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_SPI_NOR_USE_4K_SECTORS               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_SST25L                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_SWAP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_TESTS                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_MTD_UBI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_UBI_BEB_LIMIT                        policy<{'amd64': '20', 'arm64': '20', 'armhf': '20', 'ppc64el': '20'}>
+CONFIG_MTD_UBI_BLOCK                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_UBI_FASTMAP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MTD_UBI_GLUEBI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MTD_UBI_WL_THRESHOLD                     policy<{'amd64': '4096', 'arm64': '4096', 'armhf': '4096', 'ppc64el': '4096'}>
+CONFIG_MTK_CMDQ                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_CMDQ_MBOX                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_CQDMA                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_DEVAPC                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_EFUSE                                policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_MTK_HSDMA                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_INFRACFG                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MTK_IOMMU                                policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_MTK_IOMMU_V1                             policy<{'armhf': 'n'}>
+CONFIG_MTK_MMSYS                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MTK_PMIC_WRAP                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_SCP                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_SCPSYS                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MTK_SCPSYS_PM_DOMAINS                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MTK_SMI                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_THERMAL                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTK_TIMER                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MTK_UART_APDMA                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MTRR                                     policy<{'amd64': 'y'}>
+CONFIG_MTRR_SANITIZER                           policy<{'amd64': 'y'}>
+CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT            policy<{'amd64': '1'}>
+CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT      policy<{'amd64': '1'}>
+CONFIG_MULTIPLEXER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MULTIUSER                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MUSB_PIO_ONLY                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_MUTEX_SPIN_ON_OWNER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_MUX_ADG792A                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MUX_ADGS1408                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MUX_GPIO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MUX_MMIO                                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MV643XX_ETH                              policy<{'armhf': 'm'}>
+CONFIG_MVEBU_CLK_COMMON                         policy<{'armhf': 'y'}>
+CONFIG_MVEBU_CLK_COREDIV                        policy<{'armhf': 'y'}>
+CONFIG_MVEBU_CLK_CPU                            policy<{'armhf': 'y'}>
+CONFIG_MVEBU_DEVBUS                             policy<{'armhf': 'y'}>
+CONFIG_MVEBU_GICP                               policy<{'arm64': 'y'}>
+CONFIG_MVEBU_ICU                                policy<{'arm64': 'y'}>
+CONFIG_MVEBU_MBUS                               policy<{'armhf': 'y'}>
+CONFIG_MVEBU_ODMI                               policy<{'arm64': 'y'}>
+CONFIG_MVEBU_PIC                                policy<{'arm64': 'y'}>
+CONFIG_MVEBU_SEI                                policy<{'arm64': 'y'}>
+CONFIG_MVMDIO                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MVNETA                                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MVNETA_BM_ENABLE                         policy<{'armhf': 'n'}>
+CONFIG_MVPP2                                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_MVPP2_PTP                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MV_XOR                                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_MV_XOR_V2                                policy<{'arm64': 'y'}>
+CONFIG_MWAVE                                    policy<{'amd64': 'm'}>
+CONFIG_MWIFIEX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MWIFIEX_PCIE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MWIFIEX_SDIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MWIFIEX_USB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MWL8K                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MX3_IPU                                  policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_MX3_IPU_IRQS                             policy<{'arm64': '4', 'armhf-generic': '4'}>
+CONFIG_MXC4005                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MXC6255                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MXC_CLK                                  policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_MXC_CLK_SCU                              policy<{'arm64': 'y'}>
+CONFIG_MXC_TZIC                                 policy<{'armhf-generic': 'y'}>
+CONFIG_MXM_WMI                                  policy<{'amd64': 'm'}>
+CONFIG_MXS_DMA                                  policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_MYRI10GE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_MYRI10GE_DCA                             policy<{'amd64': 'y'}>
+CONFIG_NAMESPACES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NATIONAL_PHY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NATSEMI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NAU7802                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NBPFAXI_DMA                              policy<{'armhf': 'm'}>
+CONFIG_NCSI_OEM_CMD_GET_MAC                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NCSI_OEM_CMD_KEEP_PHY                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NDC_DIS_DYNAMIC_CACHING                  policy<{'arm64': 'y'}>
+CONFIG_ND_BLK                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_ND_BTT                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_ND_CLAIM                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y'}>
+CONFIG_ND_PFN                                   policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_NE2K_PCI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NEED_DMA_MAP_STATE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK            policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_NEED_SG_DMA_LENGTH                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NEON                                     policy<{'armhf': 'y'}>
+CONFIG_NET                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETCONSOLE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETCONSOLE_DYNAMIC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETDEVICES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETDEVSIM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETDEV_NOTIFIER_ERROR_INJECT             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NETFILTER                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_ADVANCED                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_CONNCOUNT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_FAMILY_ARP                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_FAMILY_BRIDGE                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_INGRESS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_NETLINK                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_NETLINK_ACCT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_NETLINK_GLUE_CT                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_NETLINK_HOOK                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_NETLINK_LOG                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_NETLINK_OSF                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_NETLINK_QUEUE                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_SYNPROXY                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XTABLES                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XTABLES_COMPAT                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFILTER_XT_CONNMARK                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MARK                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_BPF                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CGROUP                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CLUSTER               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_COMMENT               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CONNMARK              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_CPU                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_DCCP                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_DSCP                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_ECN                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_ESP                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_HELPER                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_HL                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_IPCOMP                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_IPRANGE               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_IPVS                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_L2TP                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_LENGTH                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_LIMIT                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_MAC                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_MARK                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_NFACCT                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_OSF                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_OWNER                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_PHYSDEV               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_POLICY                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_QUOTA                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_RATEEST               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_REALM                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_RECENT                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_SCTP                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_SOCKET                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_STATE                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_STATISTIC             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_STRING                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_TCPMSS                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_TIME                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_MATCH_U32                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_NAT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_SET                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_AUDIT                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_CONNMARK             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_CONNSECMARK          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_CT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_DSCP                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_HL                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_HMARK                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_LED                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_LOG                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_MARK                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_MASQUERADE           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_NETMAP               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_NFLOG                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_NOTRACK              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NETFILTER_XT_TARGET_RATEEST              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_REDIRECT             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_SECMARK              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_TCPMSS               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_TEE                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_TPROXY               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFILTER_XT_TARGET_TRACE                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETFS_STATS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETFS_SUPPORT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETIUCV                                  policy<{'s390x': 'm'}>
+CONFIG_NETLABEL                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETLINK_DIAG                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NETPOLL                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETROM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NETWORK_FILESYSTEMS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETWORK_SECMARK                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NETXEN_NIC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_9P_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NET_9P_RDMA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_9P_VIRTIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_9P_XEN                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_NET_ACT_BPF                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_CONNMARK                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_CSUM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_CT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_CTINFO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_GACT                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_GATE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_IFE                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NET_ACT_IPT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_MIRRED                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_MPLS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_NAT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_PEDIT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_POLICE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_SAMPLE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_SIMP                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_SKBEDIT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_SKBMOD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_TUNNEL_KEY                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_ACT_VLAN                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CALXEDA_XGMAC                        policy<{'armhf': 'm'}>
+CONFIG_NET_CLS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_CLS_ACT                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_CLS_BASIC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_BPF                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_CGROUP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_FLOW                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_FLOWER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_FW                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_MATCHALL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_ROUTE4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CLS_U32                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_CORE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_DEVLINK                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_DSA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NET_DSA_AR9331                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_BCM_SF2                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_HIRSCHMANN_HELLCREEK             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_LANTIQ_GSWIP                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_LOOP                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ8795                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ8795_SPI            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ8863_SMI            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ9477                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ9477_I2C            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ9477_SPI            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MICROCHIP_KSZ_COMMON             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MSCC_FELIX                       policy<{'arm64': 'm', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NET_DSA_MSCC_SEVILLE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MT7530                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MV88E6060                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MV88E6XXX                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_MV88E6XXX_PTP                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_DSA_QCA8K                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_REALTEK_SMI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_SJA1105                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_SJA1105_PTP                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_DSA_SJA1105_TAS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_DSA_SJA1105_VL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_DSA_SMSC_LAN9303                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_SMSC_LAN9303_I2C                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_SMSC_LAN9303_MDIO                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_AR9331                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_BRCM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_BRCM_COMMON                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_BRCM_LEGACY                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_BRCM_PREPEND                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_DSA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_DSA_COMMON                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_EDSA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_GSWIP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_HELLCREEK                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_KSZ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_LAN9303                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_MTK                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_OCELOT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_OCELOT_8021Q                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_QCA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_RTL4_A                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_SJA1105                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_TRAILER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_TAG_XRS700X                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_VITESSE_VSC73XX                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_VITESSE_VSC73XX_PLATFORM         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_VITESSE_VSC73XX_SPI              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_XRS700X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_XRS700X_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_DSA_XRS700X_MDIO                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_EGRESS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_EMATCH                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_EMATCH_CANID                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NET_EMATCH_CMP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_EMATCH_IPSET                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_EMATCH_IPT                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_EMATCH_META                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_EMATCH_NBYTE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_EMATCH_STACK                         policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32', 's390x': '32'}>
+CONFIG_NET_EMATCH_TEXT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_EMATCH_U32                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_FAILOVER                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_FC                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_FLOW_LIMIT                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_FOU                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_FOU_IP_TUNNELS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_IFE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_INGRESS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_IPGRE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_IPGRE_BROADCAST                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_IPGRE_DEMUX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_IPIP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_IPVTI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_IP_TUNNEL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_KEY                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_KEY_MIGRATE                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NET_L3_MASTER_DEV                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_MPLS_GSO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_NCSI                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_NS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_NSH                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_PKTGEN                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_POLL_CONTROLLER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_PTP_CLASSIFY                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_REDIRECT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_RX_BUSY_POLL                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_SB1000                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_NET_SCHED                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_SCH_CAKE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_CBS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_CHOKE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_CODEL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_DEFAULT                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NET_SCH_DRR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_ETF                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_ETS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_FIFO                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_SCH_FQ                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_FQ_CODEL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_FQ_PIE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_GRED                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_HFSC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_HHF                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_HTB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_INGRESS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_MQPRIO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_MULTIQ                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_NETEM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_PIE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_PLUG                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_PRIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_QFQ                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_RED                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_SFB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_SFQ                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_SKBPRIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_TAPRIO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_TBF                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SCH_TEQL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_SELFTESTS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_NET_SOCK_MSG                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_TC_SKB_EXT                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_TEAM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_TEAM_MODE_BROADCAST                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_TEAM_MODE_LOADBALANCE                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_TEAM_MODE_RANDOM                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_TEAM_MODE_ROUNDROBIN                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_TULIP                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_UDP_TUNNEL                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_VENDOR_3COM                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_8390                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_VENDOR_ACTIONS                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_NET_VENDOR_ADAPTEC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_AGERE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_ALACRITECH                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_ALLWINNER                     policy<{'arm64': 'y'}>
+CONFIG_NET_VENDOR_ALTEON                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_AMAZON                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_AMD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_AQUANTIA                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_ARC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_ATHEROS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_BROADCOM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_BROCADE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_CADENCE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_CAVIUM                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_CHELSIO                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_CIRRUS                        policy<{'amd64': '-', 'armhf': 'y'}>
+CONFIG_NET_VENDOR_CISCO                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_CORTINA                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_DEC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_DLINK                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_EZCHIP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_FARADAY                       policy<{'armhf': 'y'}>
+CONFIG_NET_VENDOR_FREESCALE                     policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_VENDOR_FUJITSU                       policy<{'amd64': 'y'}>
+CONFIG_NET_VENDOR_GOOGLE                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_HISILICON                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_NET_VENDOR_HUAWEI                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_I825XX                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NET_VENDOR_IBM                           policy<{'ppc64el': 'y'}>
+CONFIG_NET_VENDOR_INTEL                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_LITEX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_MARVELL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_MEDIATEK                      policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_NET_VENDOR_MELLANOX                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_MICREL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_MICROCHIP                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_MICROSEMI                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_MICROSOFT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_MYRI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_NATSEMI                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_NETERION                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_NETRONOME                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_NI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_NVIDIA                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_OKI                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_PACKET_ENGINES                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_PENSANDO                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_QLOGIC                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_QUALCOMM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_RDC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_REALTEK                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_RENESAS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_ROCKER                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SAMSUNG                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SEEQ                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SILAN                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SIS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SMSC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SOCIONEXT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_SOLARFLARE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_STMICRO                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SUN                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_SYNOPSYS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_TEHUTI                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_TI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_VIA                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_WIZNET                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NET_VENDOR_XILINX                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NET_VENDOR_XIRCOM                        policy<{'amd64': 'y'}>
+CONFIG_NET_VRF                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NET_XGENE                                policy<{'arm64': 'm'}>
+CONFIG_NET_XGENE_V2                             policy<{'arm64': 'm'}>
+CONFIG_NEW_LEDS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_NFC                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NFC_DIGITAL                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_FDP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_FDP_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_HCI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MEI_PHY                              policy<{'amd64': 'm'}>
+CONFIG_NFC_MICROREAD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MICROREAD_I2C                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MICROREAD_MEI                        policy<{'amd64': 'm'}>
+CONFIG_NFC_MRVL                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MRVL_I2C                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MRVL_SPI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MRVL_UART                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_MRVL_USB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_NCI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_NCI_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_NCI_UART                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_NXP_NCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_NXP_NCI_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN532_UART                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN533                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN533_I2C                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN533_USB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN544                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN544_I2C                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_PN544_MEI                            policy<{'amd64': 'm'}>
+CONFIG_NFC_PORT100                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_S3FWRN5                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_S3FWRN5_I2C                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_S3FWRN82_UART                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_SHDLC                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NFC_SIM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_ST21NFCA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_ST21NFCA_I2C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_ST95HF                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_ST_NCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_ST_NCI_I2C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_ST_NCI_SPI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_TRF7970A                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFC_VIRTUAL_NCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFIT_SECURITY_DEBUG                      policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_NFP                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NFP_APP_ABM_NIC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NFP_APP_FLOWER                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NFP_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NFSD                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFSD_BLOCKLAYOUT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_FLEXFILELAYOUT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_PNFS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_SCSILAYOUT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_V2                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_V2_ACL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_V3_ACL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_V4                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_V4_2_INTER_SSC                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFSD_V4_SECURITY_LABEL                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_ACL_SUPPORT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFS_COMMON                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_DEBUG                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_DISABLE_UDP_SUPPORT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFS_FSCACHE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_SWAP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_USE_KERNEL_DNS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_USE_LEGACY_DNS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NFS_V2                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFS_V3                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFS_V3_ACL                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_V4                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFS_V4_1                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_V4_1_IMPLEMENTATION_ID_DOMAIN        policy<{'amd64': '"kernel.org"', 'arm64': '"kernel.org"', 'armhf': '"kernel.org"', 'ppc64el': '"kernel.org"', 's390x': '"kernel.org"'}>
+CONFIG_NFS_V4_1_MIGRATION                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_V4_2                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_V4_2_READ_PLUS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NFS_V4_2_SSC_HELPER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFS_V4_SECURITY_LABEL                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NFTL                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NFTL_RW                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NFT_BRIDGE_META                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_BRIDGE_REJECT                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_COMPAT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_CONNLIMIT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_COUNTER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_CT                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_DUP_IPV4                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_DUP_IPV6                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_DUP_NETDEV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FIB                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FIB_INET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FIB_IPV4                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FIB_IPV6                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FIB_NETDEV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FLOW_OFFLOAD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_FWD_NETDEV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_HASH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_LIMIT                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_LOG                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_MASQ                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_NAT                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_NUMGEN                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_OBJREF                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_OSF                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_QUEUE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_QUOTA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_REDIR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_REJECT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_REJECT_INET                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_REJECT_IPV4                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_REJECT_IPV6                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_REJECT_NETDEV                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_SOCKET                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_SYNPROXY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_TPROXY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_TUNNEL                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NFT_XFRM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_AMANDA                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_BRIDGE                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_BROADCAST                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_EVENTS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CONNTRACK_FTP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_H323                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_IRC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_LABELS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CONNTRACK_MARK                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CONNTRACK_NETBIOS_NS                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_PPTP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_PROCFS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NF_CONNTRACK_SANE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_SECMARK                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CONNTRACK_SIP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_SNMP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_TFTP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CONNTRACK_TIMEOUT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CONNTRACK_TIMESTAMP                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CONNTRACK_ZONES                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CT_NETLINK                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CT_NETLINK_HELPER                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CT_NETLINK_TIMEOUT                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_CT_PROTO_DCCP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CT_PROTO_GRE                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CT_PROTO_SCTP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_CT_PROTO_UDPLITE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_DEFRAG_IPV4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_DEFRAG_IPV6                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_DUP_IPV4                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_DUP_IPV6                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_DUP_NETDEV                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_FLOW_TABLE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_FLOW_TABLE_INET                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_FLOW_TABLE_IPV4                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_FLOW_TABLE_IPV6                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_FLOW_TABLE_PROCFS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_LOG_ARP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_LOG_IPV4                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_LOG_IPV6                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_LOG_SYSLOG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_AMANDA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_FTP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_H323                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_IRC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_MASQUERADE                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_NAT_PPTP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_REDIRECT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_NAT_SIP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_SNMP_BASIC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_NAT_TFTP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_REJECT_IPV4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_REJECT_IPV6                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_SOCKET_IPV4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_SOCKET_IPV6                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_TABLES                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_TABLES_ARP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_TABLES_BRIDGE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_TABLES_INET                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_TABLES_IPV4                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_TABLES_IPV6                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_TABLES_NETDEV                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NF_TPROXY_IPV4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NF_TPROXY_IPV6                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NI903X_WDT                               policy<{'amd64': 'm'}>
+CONFIG_NIC7018_WDT                              policy<{'amd64': 'm'}>
+CONFIG_NILFS2_FS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NITRO_ENCLAVES                           policy<{'amd64': 'm'}>
+CONFIG_NIU                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NI_XGE_MANAGEMENT_ENET                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NL80211_TESTMODE                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NLATTR                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NLMON                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ASCII                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_1250                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_1251                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_437                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NLS_CODEPAGE_737                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_775                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_850                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_852                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_855                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_857                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_860                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_861                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_862                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_863                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_864                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_865                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_866                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_869                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_874                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_932                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_936                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_949                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_CODEPAGE_950                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_DEFAULT                              policy<{'amd64': '"utf8"', 'arm64': '"utf8"', 'armhf': '"utf8"', 'ppc64el': '"utf8"', 's390x': '"utf8"'}>
+CONFIG_NLS_ISO8859_1                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_13                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_14                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_15                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_2                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_3                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_4                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_5                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_6                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_7                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_8                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_ISO8859_9                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_KOI8_R                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_KOI8_U                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_CELTIC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_CENTEURO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_CROATIAN                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_CYRILLIC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_GAELIC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_GREEK                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_ICELAND                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_INUIT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_ROMAN                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_ROMANIAN                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_MAC_TURKISH                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NLS_UTF8                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NMI_IPI                                  policy<{'ppc64el': 'y'}>
+CONFIG_NOA1305                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NODES_SHIFT                              policy<{'amd64': '10', 'arm64': '6', 'ppc64el': '8', 's390x': '1'}>
+CONFIG_NOKIA_MODEM                              policy<{'armhf-generic': 'm'}>
+CONFIG_NONSTATIC_KERNEL                         policy<{'ppc64el': 'y'}>
+CONFIG_NOP_TRACER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NORTEL_HERMES                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NOTIFIER_ERROR_INJECTION                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NOUVEAU_DEBUG                            policy<{'amd64': '5', 'arm64': '5', 'armhf': '5', 'ppc64el': '5'}>
+CONFIG_NOUVEAU_DEBUG_DEFAULT                    policy<{'amd64': '3', 'arm64': '3', 'armhf': '3', 'ppc64el': '3'}>
+CONFIG_NOUVEAU_DEBUG_MMU                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NOUVEAU_DEBUG_PUSH                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NOUVEAU_PLATFORM_DRIVER                  policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_NOZOMI                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NO_HZ                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NO_HZ_COMMON                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NO_HZ_FULL                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NO_IOPORT_MAP                            policy<{'armhf': 'y', 's390x': 'y'}>
+CONFIG_NPCM7XX_KCS_IPMI_BMC                     policy<{'armhf': 'm'}>
+CONFIG_NPCM7XX_TIMER                            policy<{'armhf': 'y'}>
+CONFIG_NPCM7XX_WATCHDOG                         policy<{'armhf': 'y'}>
+CONFIG_NPCM_ADC                                 policy<{'armhf': 'm'}>
+CONFIG_NR_CPUS_DEFAULT                          policy<{'amd64': '8192'}>
+CONFIG_NR_CPUS_RANGE_BEGIN                      policy<{'amd64': '8192'}>
+CONFIG_NR_CPUS_RANGE_END                        policy<{'amd64': '8192'}>
+CONFIG_NR_IRQS                                  policy<{'ppc64el': '512'}>
+CONFIG_NS83820                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NTB_AMD                                  policy<{'amd64': 'n'}>
+CONFIG_NTB_EPF                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_IDT                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_INTEL                                policy<{'amd64': 'm'}>
+CONFIG_NTB_MSI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NTB_MSI_TEST                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_NTB_NETDEV                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_PERF                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_PINGPONG                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_SWITCHTEC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_TOOL                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTB_TRANSPORT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NTFS3_64BIT_CLUSTER                      policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NTFS3_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NTFS3_FS_POSIX_ACL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NTFS3_LZX_XPRESS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NTFS_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NTFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NTFS_RW                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_NULL_TTY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NUMA_BALANCING                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NUMA_KEEP_MEMINFO                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NVDIMM_DAX                               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_NVDIMM_KEYS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y'}>
+CONFIG_NVDIMM_PFN                               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_NVEC_PAZ00                               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_NVEC_POWER                               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_NVHE_EL2_DEBUG                           policy<{'arm64': 'n'}>
+CONFIG_NVIDIA_CARMEL_CNP_ERRATUM                policy<{'arm64': 'y'}>
+CONFIG_NVIDIA_WMI_EC_BACKLIGHT                  policy<{'amd64': 'm'}>
+CONFIG_NVMEM_BCM_OCOTP                          policy<{'arm64': 'm'}>
+CONFIG_NVMEM_IMX_IIM                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_NVMEM_IMX_OCOTP                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_NVMEM_IMX_OCOTP_SCU                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_NVMEM_REBOOT_MODE                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NVMEM_RMEM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NVMEM_SNVS_LPGPR                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_NVMEM_SPMI_SDAM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_NVMEM_SUNXI_SID                          policy<{'arm64': 'm'}>
+CONFIG_NVMEM_SYSFS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NVMEM_VF610_OCOTP                        policy<{'armhf-generic': 'n'}>
+CONFIG_NVMEM_ZYNQMP                             policy<{'arm64': 'y'}>
+CONFIG_NVME_CORE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_FABRICS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_FC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_HWMON                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_NVME_MULTIPATH                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NVME_RDMA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_TARGET                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_TARGET_FC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_TARGET_FCLOOP                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_NVME_TARGET_LOOP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_TARGET_PASSTHRU                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_NVME_TARGET_RDMA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_TARGET_TCP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NVME_TCP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_NV_TCO                                   policy<{'amd64': 'm'}>
+CONFIG_NXP_C45_TJA11XX_PHY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_NXP_TJA11XX_PHY                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_N_HDLC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_OABI_COMPAT                              policy<{'armhf': 'n'}>
+CONFIG_OBJAGG                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OCFS2_DEBUG_FS                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_OCFS2_DEBUG_MASKLOG                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_OCFS2_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OCFS2_FS_O2CB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OCFS2_FS_STATS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_OCFS2_FS_USERSPACE_CLUSTER               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OCTEONTX2_AF                             policy<{'arm64': 'm'}>
+CONFIG_OCTEONTX2_MBOX                           policy<{'arm64': 'm'}>
+CONFIG_OCTEONTX2_PF                             policy<{'arm64': 'm'}>
+CONFIG_OCTEONTX2_VF                             policy<{'arm64': 'm'}>
+CONFIG_OCXL                                     policy<{'ppc64el': 'm'}>
+CONFIG_OCXL_BASE                                policy<{'ppc64el': 'y'}>
+CONFIG_OF                                       policy<{'amd64': 'n', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_OF_ADDRESS                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_DMA_DEFAULT_COHERENT                  policy<{'ppc64el': 'y'}>
+CONFIG_OF_DYNAMIC                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_EARLY_FLATTREE                        policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_FLATTREE                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_FPGA_REGION                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_OF_GPIO                                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_IOMMU                                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_IRQ                                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_KOBJ                                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_MDIO                                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_NUMA                                  policy<{'arm64': 'y'}>
+CONFIG_OF_OVERLAY                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_PMEM                                  policy<{'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_OF_RECONFIG_NOTIFIER_ERROR_INJECT        policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_OF_RESERVED_MEM                          policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_RESOLVE                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_OF_UNITTEST                              policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_OID_REGISTRY                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_OLD_SIGACTION                            policy<{'armhf': 'y', 's390x': 'y'}>
+CONFIG_OLD_SIGSUSPEND                           policy<{'ppc64el': 'y'}>
+CONFIG_OLD_SIGSUSPEND3                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_OMAP2PLUS_MBOX                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_OMAP2_VRFB                               policy<{'armhf-generic': 'y'}>
+CONFIG_OMAP3_L2_AUX_SECURE_SAVE_RESTORE         policy<{'armhf-generic': 'n'}>
+CONFIG_OMAP3_SDRC_AC_TIMING                     policy<{'armhf-generic': 'n'}>
+CONFIG_OMAP3_THERMAL                            policy<{'armhf-generic': 'n'}>
+CONFIG_OMAP4_THERMAL                            policy<{'armhf-generic': 'y'}>
+CONFIG_OMAP5_ERRATA_801819                      policy<{'armhf': 'y'}>
+CONFIG_OMAP_32K_TIMER                           policy<{'armhf': 'y'}>
+CONFIG_OMAP_CONTROL_PHY                         policy<{'armhf': 'm'}>
+CONFIG_OMAP_DM_TIMER                            policy<{'armhf': 'y'}>
+CONFIG_OMAP_GPMC                                policy<{'armhf': 'y'}>
+CONFIG_OMAP_GPMC_DEBUG                          policy<{'armhf': 'n'}>
+CONFIG_OMAP_HWMOD                               policy<{'armhf-generic': 'y'}>
+CONFIG_OMAP_INTERCONNECT                        policy<{'armhf': 'y'}>
+CONFIG_OMAP_INTERCONNECT_BARRIER                policy<{'armhf': 'y'}>
+CONFIG_OMAP_IOMMU                               policy<{'armhf': 'y'}>
+CONFIG_OMAP_IOMMU_DEBUG                         policy<{'armhf': 'n'}>
+CONFIG_OMAP_IRQCHIP                             policy<{'armhf': 'y'}>
+CONFIG_OMAP_MBOX_KFIFO_SIZE                     policy<{'arm64': '256', 'armhf': '256'}>
+CONFIG_OMAP_OCP2SCP                             policy<{'armhf': 'm'}>
+CONFIG_OMAP_REMOTEPROC                          policy<{'armhf': 'm'}>
+CONFIG_OMAP_REMOTEPROC_WATCHDOG                 policy<{'armhf': 'n'}>
+CONFIG_OMAP_RESET_CLOCKS                        policy<{'armhf': 'y'}>
+CONFIG_OMAP_SSI                                 policy<{'armhf-generic': 'm'}>
+CONFIG_OMAP_USB2                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_OMAP_WATCHDOG                            policy<{'armhf': 'm'}>
+CONFIG_OMFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_OPAL_CORE                                policy<{'ppc64el': 'n'}>
+CONFIG_OPAL_PRD                                 policy<{'ppc64el': 'm'}>
+CONFIG_OPENVSWITCH                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OPENVSWITCH_GENEVE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OPENVSWITCH_GRE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OPENVSWITCH_VXLAN                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OPT3001                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_OPTEE                                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_OPTEE_SHM_NUM_PRIV_PAGES                 policy<{'arm64': '1', 'armhf': '1'}>
+CONFIG_OPTPROBES                                policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ORANGEFS_FS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ORINOCO_USB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ORION_IRQCHIP                            policy<{'armhf': 'y'}>
+CONFIG_ORION_TIMER                              policy<{'armhf': 'y'}>
+CONFIG_ORION_WATCHDOG                           policy<{'armhf': 'm'}>
+CONFIG_OSF_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_OUTER_CACHE                              policy<{'armhf': 'y'}>
+CONFIG_OUTER_CACHE_SYNC                         policy<{'armhf': 'y'}>
+CONFIG_OUTPUT_FORMAT                            policy<{'amd64': '"elf64-x86-64"'}>
+CONFIG_OVERLAY_FS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_OVERLAY_FS_INDEX                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_OVERLAY_FS_METACOPY                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_OVERLAY_FS_REDIRECT_ALWAYS_FOLLOW        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_OVERLAY_FS_REDIRECT_DIR                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_OVERLAY_FS_XINO_AUTO                     policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_OWL_DMA                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_OWL_EMAC                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_OWL_PM_DOMAINS                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_OWL_PM_DOMAINS_HELPER                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_OWL_TIMER                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_P54_COMMON                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_P54_LEDS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_P54_PCI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_P54_SPI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_P54_SPI_DEFAULT_EEPROM                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_P54_USB                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PA12203001                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PACKET                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PACKET_DIAG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PACKING                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PACK_STACK                               policy<{'s390x': 'y'}>
+CONFIG_PADATA                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAGE_COUNTER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAGE_EXTENSION                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'y', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PAGE_IDLE_FLAG                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAGE_OFFSET                              policy<{'armhf': '0xC0000000', 'ppc64el': '0xc000000000000000'}>
+CONFIG_PAGE_OWNER                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PAGE_POOL                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAGE_REPORTING                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAGE_TABLE_ISOLATION                     policy<{'amd64': 'y'}>
+CONFIG_PAHOLE_HAS_SPLIT_BTF                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PAHOLE_VERSION                           policy<{'amd64': '125', 'arm64': '125', 'armhf': '125', 'ppc64el': '125', 's390x': '125'}>
+CONFIG_PALMAS_GPADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PANASONIC_LAPTOP                         policy<{'amd64': 'm'}>
+CONFIG_PANEL                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PANEL_CHANGE_MESSAGE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PANEL_PARPORT                            policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_PANEL_PROFILE                            policy<{'amd64': '5', 'arm64': '5', 'armhf': '5', 'ppc64el': '5'}>
+CONFIG_PANIC_ON_OOPS_VALUE                      policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_PANIC_TIMEOUT                            policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '10', 's390x': '0'}>
+CONFIG_PANTHERLORD_FF                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PAPR_SCM                                 policy<{'ppc64el': 'm'}>
+CONFIG_PARAVIRT                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n'}>
+CONFIG_PARAVIRT_CLOCK                           policy<{'amd64': 'y'}>
+CONFIG_PARAVIRT_DEBUG                           policy<{'amd64': 'n'}>
+CONFIG_PARAVIRT_SPINLOCKS                       policy<{'amd64': 'y'}>
+CONFIG_PARAVIRT_TIME_ACCOUNTING                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n'}>
+CONFIG_PARAVIRT_XXL                             policy<{'amd64': 'y'}>
+CONFIG_PARIDE                                   policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_ATEN                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_BPCK                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_BPCK6                             policy<{'armhf': 'm'}>
+CONFIG_PARIDE_COMM                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_DSTR                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_EPAT                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_EPATC8                            policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PARIDE_EPIA                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_FIT2                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_FIT3                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_FRIQ                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_FRPW                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_KBIC                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_KTTI                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_ON20                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_ON26                              policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_PCD                               policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_PD                                policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_PF                                policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_PG                                policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARIDE_PT                                policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARMAN                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PARPORT                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PARPORT_1284                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PARPORT_AX88796                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARPORT_NOT_PC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PARPORT_PANEL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARPORT_PC                               policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARPORT_PC_FIFO                          policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PARPORT_PC_PCMCIA                        policy<{'amd64': 'm'}>
+CONFIG_PARPORT_PC_SUPERIO                       policy<{'amd64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PARPORT_SERIAL                           policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PARTITION_ADVANCED                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PARTITION_PERCPU                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PATA_ACPI                                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_PATA_ALI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_AMD                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_ARTOP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_ATIIXP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_ATP867X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_CMD640_PCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_CMD64X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_CYPRESS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_EFAR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_HPT366                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_HPT37X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_HPT3X2N                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_HPT3X3                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_IMX                                 policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PATA_IT8213                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_IT821X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_JMICRON                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_LEGACY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_MARVELL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_MPIIX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_NETCELL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_NINJA32                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_NS87410                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_NS87415                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_OF_PLATFORM                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_OLDPIIX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_OPTI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_OPTIDMA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_PCMCIA                              policy<{'amd64': 'm'}>
+CONFIG_PATA_PDC2027X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_PDC_OLD                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_PLATFORM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_RADISYS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_RDC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_RZ1000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_SCH                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_SERVERWORKS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_SIL680                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_SIS                                 policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_TIMINGS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PATA_TOSHIBA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_TRIFLEX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_VIA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PATA_WINBOND                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PC104                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PC300TOO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PC87413_WDT                              policy<{'amd64': 'm'}>
+CONFIG_PCC                                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_PCCARD                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCCARD_NONSTATIC                         policy<{'amd64': 'y'}>
+CONFIG_PCENGINES_APU2                           policy<{'amd64': 'm'}>
+CONFIG_PCF50633_ADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PCF50633_GPIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PCI                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI200SYN                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PCIEAER                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_PCIEAER_INJECT                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_PCIEASPM                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIEASPM_PERFORMANCE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIEASPM_POWERSAVE                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIEASPM_POWER_SUPERSAVE                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIE_AL                                  policy<{'arm64': 'y'}>
+CONFIG_PCIE_ALTERA                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_ALTERA_MSI                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_ARMADA_8K                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_BRCMSTB                             policy<{'arm64': 'm'}>
+CONFIG_PCIE_BUS_DEFAULT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_BUS_PEER2PEER                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIE_BUS_PERFORMANCE                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIE_BUS_SAFE                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIE_BUS_TUNE_OFF                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCIE_CADENCE                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_CADENCE_EP                          policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_CADENCE_HOST                        policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_CADENCE_PLAT                        policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_CADENCE_PLAT_EP                     policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_CADENCE_PLAT_HOST                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_DPC                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_PCIE_DW                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_DW_EP                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_DW_HOST                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_DW_PLAT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_DW_PLAT_EP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_DW_PLAT_HOST                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_ECRC                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 's390x': 'n'}>
+CONFIG_PCIE_HISI_ERR                            policy<{'arm64': 'y'}>
+CONFIG_PCIE_HISI_STB                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_IPROC                               policy<{'arm64': 'm'}>
+CONFIG_PCIE_IPROC_MSI                           policy<{'arm64': 'y'}>
+CONFIG_PCIE_IPROC_PLATFORM                      policy<{'arm64': 'm'}>
+CONFIG_PCIE_KEEMBAY                             policy<{'arm64': 'y'}>
+CONFIG_PCIE_KEEMBAY_EP                          policy<{'arm64': 'y'}>
+CONFIG_PCIE_KEEMBAY_HOST                        policy<{'arm64': 'y'}>
+CONFIG_PCIE_KIRIN                               policy<{'arm64': 'y'}>
+CONFIG_PCIE_LAYERSCAPE_GEN4                     policy<{'arm64': 'n'}>
+CONFIG_PCIE_MEDIATEK                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_MEDIATEK_GEN3                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PCIE_MICROCHIP_HOST                      policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_MOBIVEIL_PLAT                       policy<{'arm64': 'n'}>
+CONFIG_PCIE_PME                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_PTM                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCIE_QCOM                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_RCAR_EP                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_RCAR_HOST                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_ROCKCHIP                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_ROCKCHIP_DW_HOST                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_ROCKCHIP_EP                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCIE_ROCKCHIP_HOST                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PCIE_TEGRA194                            policy<{'arm64': 'm'}>
+CONFIG_PCIE_TEGRA194_EP                         policy<{'arm64': 'm'}>
+CONFIG_PCIE_TEGRA194_HOST                       policy<{'arm64': 'm'}>
+CONFIG_PCIE_UNIPHIER                            policy<{'armhf': 'y'}>
+CONFIG_PCIE_UNIPHIER_EP                         policy<{'armhf': 'y'}>
+CONFIG_PCIE_VISCONTI_HOST                       policy<{'arm64': 'y'}>
+CONFIG_PCIE_XILINX                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCIE_XILINX_CPM                          policy<{'arm64': 'y'}>
+CONFIG_PCIE_XILINX_NWL                          policy<{'arm64': 'y'}>
+CONFIG_PCIPCWATCHDOG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PCI_AARDVARK                             policy<{'arm64': 'y'}>
+CONFIG_PCI_ATMEL                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PCI_ATS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_BRIDGE_EMUL                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCI_CNB20LE_QUIRK                        policy<{'amd64': 'n'}>
+CONFIG_PCI_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCI_DIRECT                               policy<{'amd64': 'y'}>
+CONFIG_PCI_DOMAINS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_DOMAINS_GENERIC                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCI_DRA7XX                               policy<{'armhf': 'y'}>
+CONFIG_PCI_DRA7XX_EP                            policy<{'armhf': 'y'}>
+CONFIG_PCI_DRA7XX_HOST                          policy<{'armhf': 'y'}>
+CONFIG_PCI_ECAM                                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_ENDPOINT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_ENDPOINT_CONFIGFS                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_ENDPOINT_TEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCI_EPF_NTB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PCI_EPF_TEST                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCI_EPF_VNTB                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PCI_EXYNOS                               policy<{'armhf': 'm'}>
+CONFIG_PCI_FTPCI100                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_HISI                                 policy<{'arm64': 'y'}>
+CONFIG_PCI_HOST_COMMON                          policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_HOST_GENERIC                         policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_HOST_THUNDER_ECAM                    policy<{'arm64': 'y'}>
+CONFIG_PCI_HOST_THUNDER_PEM                     policy<{'arm64': 'y'}>
+CONFIG_PCI_HYPERV                               policy<{'amd64': 'm'}>
+CONFIG_PCI_HYPERV_INTERFACE                     policy<{'amd64': 'm'}>
+CONFIG_PCI_IMX6                                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PCI_IOV                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_J721E                                policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_J721E_EP                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_J721E_HOST                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_KEYSTONE                             policy<{'arm64': 'y'}>
+CONFIG_PCI_KEYSTONE_EP                          policy<{'arm64': 'y'}>
+CONFIG_PCI_KEYSTONE_HOST                        policy<{'arm64': 'y'}>
+CONFIG_PCI_LABEL                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCI_LAYERSCAPE                           policy<{'arm64': 'y', 'armhf': 'n'}>
+CONFIG_PCI_LAYERSCAPE_EP                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PCI_LOCKLESS_CONFIG                      policy<{'amd64': 'y'}>
+CONFIG_PCI_MMCONFIG                             policy<{'amd64': 'y'}>
+CONFIG_PCI_MSI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_MSI_ARCH_FALLBACKS                   policy<{'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_MSI_IRQ_DOMAIN                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_MVEBU                                policy<{'armhf': 'y'}>
+CONFIG_PCI_P2PDMA                               policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n'}>
+CONFIG_PCI_PASID                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PCI_PF_STUB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PCI_PRI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PCI_QUIRKS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PCI_RCAR_GEN2                            policy<{'armhf': 'y'}>
+CONFIG_PCI_REALLOC_ENABLE_AUTO                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCI_STUB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PCI_SW_SWITCHTEC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PCI_SYSCALL                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PCI_TEGRA                                policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PCI_V3_SEMI                              policy<{'armhf': 'y'}>
+CONFIG_PCI_XEN                                  policy<{'amd64': 'y'}>
+CONFIG_PCI_XGENE                                policy<{'arm64': 'y'}>
+CONFIG_PCI_XGENE_MSI                            policy<{'arm64': 'y'}>
+CONFIG_PCMCIA                                   policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_PCMCIA_3C574                             policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_3C589                             policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_AHA152X                           policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_ATMEL                             policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_AXNET                             policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_FDOMAIN                           policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_FMVJ18X                           policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_HERMES                            policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_LOAD_CIS                          policy<{'amd64': 'y'}>
+CONFIG_PCMCIA_NMCLAN                            policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_PCNET                             policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_QLOGIC                            policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_RAYCS                             policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_SMC91C92                          policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_SPECTRUM                          policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_SYM53C500                         policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_WL3501                            policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_XIRC2PS                           policy<{'amd64': 'm'}>
+CONFIG_PCMCIA_XIRCOM                            policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_PCNET32                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PCPU_DEV_REFCNT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PCSPKR_PLATFORM                          policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_PCS_LYNX                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PCS_XPCS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PD6729                                   policy<{'amd64': 'm'}>
+CONFIG_PDA_POWER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PDC_ADMA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PEAQ_WMI                                 policy<{'amd64': 'm'}>
+CONFIG_PERCPU_STATS                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PERCPU_TEST                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PERF_EVENTS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PERF_EVENTS_AMD_POWER                    policy<{'amd64': 'n'}>
+CONFIG_PERF_EVENTS_AMD_UNCORE                   policy<{'amd64': 'm'}>
+CONFIG_PERF_EVENTS_INTEL_CSTATE                 policy<{'amd64': 'm'}>
+CONFIG_PERF_EVENTS_INTEL_RAPL                   policy<{'amd64': 'm'}>
+CONFIG_PERF_EVENTS_INTEL_UNCORE                 policy<{'amd64': 'y'}>
+CONFIG_PERF_USE_VMALLOC                         policy<{'armhf': 'y'}>
+CONFIG_PERSISTENT_KEYRINGS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PFAULT                                   policy<{'s390x': 'y'}>
+CONFIG_PGSTE                                    policy<{'s390x': 'y'}>
+CONFIG_PGTABLE_LEVELS                           policy<{'amd64': '5', 'arm64-generic': '4', 'arm64-generic-64k': '3', 'arm64-lowlatency': '4', 'arm64-lowlatency-64k': '3', 'armhf-generic': '2', 'armhf-generic-lpae': '3', 'ppc64el': '4', 's390x': '5'}>
+CONFIG_PHANTOM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PHONET                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PHYLIB                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_PHYLINK                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PHYSICAL_ALIGN                           policy<{'amd64': '0x200000'}>
+CONFIG_PHYSICAL_START                           policy<{'amd64': '0x1000000', 'ppc64el': '0x00000000'}>
+CONFIG_PHYS_ADDR_T_64BIT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PHY_AM654_SERDES                         policy<{'arm64': 'm'}>
+CONFIG_PHY_BCM_NS_USB2                          policy<{'arm64': 'm'}>
+CONFIG_PHY_BCM_NS_USB3                          policy<{'arm64': 'm'}>
+CONFIG_PHY_BCM_SR_PCIE                          policy<{'arm64': 'm'}>
+CONFIG_PHY_BCM_SR_USB                           policy<{'arm64': 'm'}>
+CONFIG_PHY_BERLIN_SATA                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_BERLIN_USB                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_BRCM_SATA                            policy<{'arm64': 'y'}>
+CONFIG_PHY_BRCM_USB                             policy<{'arm64': 'm'}>
+CONFIG_PHY_CADENCE_DPHY                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_CADENCE_SALVO                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_CADENCE_SIERRA                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_CADENCE_TORRENT                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_CAN_TRANSCEIVER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PHY_CPCAP_USB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_DM816X_USB                           policy<{'armhf': 'm'}>
+CONFIG_PHY_EXYNOS5250_SATA                      policy<{'armhf': 'y'}>
+CONFIG_PHY_EXYNOS5250_USB2                      policy<{'armhf': 'y'}>
+CONFIG_PHY_EXYNOS5_USBDRD                       policy<{'armhf': 'm'}>
+CONFIG_PHY_EXYNOS_DP_VIDEO                      policy<{'armhf': 'y'}>
+CONFIG_PHY_EXYNOS_MIPI_VIDEO                    policy<{'armhf': 'y'}>
+CONFIG_PHY_EXYNOS_PCIE                          policy<{'armhf': 'y'}>
+CONFIG_PHY_FSL_IMX8MQ_USB                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_HI3660_USB                           policy<{'arm64': 'm'}>
+CONFIG_PHY_HI3670_USB                           policy<{'arm64': 'm'}>
+CONFIG_PHY_HI6220_USB                           policy<{'arm64': 'm'}>
+CONFIG_PHY_HISI_INNO_USB2                       policy<{'arm64': 'm'}>
+CONFIG_PHY_HISTB_COMBPHY                        policy<{'arm64': 'm'}>
+CONFIG_PHY_HIX5HD2_SATA                         policy<{'armhf': 'm'}>
+CONFIG_PHY_INTEL_KEEMBAY_EMMC                   policy<{'arm64': 'm'}>
+CONFIG_PHY_INTEL_KEEMBAY_USB                    policy<{'arm64': 'm'}>
+CONFIG_PHY_INTEL_LGM_EMMC                       policy<{'amd64': 'm'}>
+CONFIG_PHY_J721E_WIZ                            policy<{'arm64': 'm'}>
+CONFIG_PHY_MAPPHONE_MDM6600                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_MESON8B_USB2                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MESON_AXG_MIPI_DPHY                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PHY_MESON_AXG_PCIE                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PHY_MESON_G12A_USB2                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MESON_G12A_USB3_PCIE                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MESON_GXL_USB2                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MIXEL_MIPI_DPHY                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_MTK_HDMI                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MTK_MIPI_DSI                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MTK_TPHY                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MTK_UFS                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MTK_XSPHY                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MVEBU_A3700_COMPHY                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MVEBU_A3700_UTMI                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MVEBU_A38X_COMPHY                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MVEBU_CP110_COMPHY                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MVEBU_CP110_UTMI                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_MVEBU_SATA                           policy<{'armhf': 'y'}>
+CONFIG_PHY_NS2_PCIE                             policy<{'arm64': 'y'}>
+CONFIG_PHY_NS2_USB_DRD                          policy<{'arm64': 'm'}>
+CONFIG_PHY_OCELOT_SERDES                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_PXA_28NM_HSIC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PHY_PXA_28NM_USB2                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PHY_QCOM_APQ8064_SATA                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_IPQ4019_USB                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_IPQ806X_SATA                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_IPQ806X_USB                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_PCIE2                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_QMP                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_QUSB2                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_USB_HS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_QCOM_USB_HSIC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_QCOM_USB_HS_28NM                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_QCOM_USB_SS                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_RCAR_GEN2                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_RCAR_GEN3_PCIE                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_RCAR_GEN3_USB2                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_RCAR_GEN3_USB3                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_DP                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_DPHY_RX0                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_EMMC                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_INNO_HDMI                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_INNO_USB2                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_PCIE                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_TYPEC                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_ROCKCHIP_USB                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PHY_SAMSUNG_UFS                          policy<{'armhf': 'm'}>
+CONFIG_PHY_SAMSUNG_USB2                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_SPARX5_SERDES                        policy<{'amd64': '-', 'arm64': 'm', 'armhf': '-', 'ppc64el': '-'}>
+CONFIG_PHY_SUN4I_USB                            policy<{'arm64': 'm'}>
+CONFIG_PHY_SUN50I_USB3                          policy<{'arm64': 'm'}>
+CONFIG_PHY_SUN6I_MIPI_DPHY                      policy<{'arm64': 'm'}>
+CONFIG_PHY_SUN9I_USB                            policy<{'arm64': 'n'}>
+CONFIG_PHY_TEGRA194_P2U                         policy<{'arm64': 'm'}>
+CONFIG_PHY_TEGRA_XUSB                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PHY_TI_GMII_SEL                          policy<{'arm64': 'm', 'armhf': 'y'}>
+CONFIG_PHY_TUSB1210                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PHY_UNIPHIER_AHCI                        policy<{'armhf': 'm'}>
+CONFIG_PHY_UNIPHIER_PCIE                        policy<{'armhf': 'm'}>
+CONFIG_PHY_UNIPHIER_USB2                        policy<{'armhf': 'm'}>
+CONFIG_PHY_UNIPHIER_USB3                        policy<{'armhf': 'm'}>
+CONFIG_PHY_XGENE                                policy<{'arm64': 'y'}>
+CONFIG_PHY_XILINX_ZYNQMP                        policy<{'arm64': 'm'}>
+CONFIG_PI433                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PID_IN_CONTEXTIDR                        policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_PID_NS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PINCONF                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PINCTRL_ALDERLAKE                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_AMD                              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_PINCTRL_APQ8064                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_APQ8084                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_ARMADA_370                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_ARMADA_375                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_ARMADA_37XX                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_ARMADA_38X                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_ARMADA_39X                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_ARMADA_AP806                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_ARMADA_CP110                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_ARMADA_XP                        policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_AS370                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_AS3722                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_ASPEED                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_ASPEED_G6                        policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_AXP209                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_BAYTRAIL                         policy<{'amd64': 'y'}>
+CONFIG_PINCTRL_BCM2835                          policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_BERLIN                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_BERLIN_BG2                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_BERLIN_BG2CD                     policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_BERLIN_BG2Q                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_BERLIN_BG4CT                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_BM1880                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_BROXTON                          policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_CANNONLAKE                       policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_CEDARFORK                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_CS47L15                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_CS47L35                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_CS47L85                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_CS47L90                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_CS47L92                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_DA9062                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_DENVERTON                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_DOVE                             policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_ELKHARTLAKE                      policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_EMMITSBURG                       policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_EXYNOS                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_EXYNOS_ARM                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_GEMINILAKE                       policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_ICELAKE                          policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_IMX                              policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX50                            policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX51                            policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX6Q                            policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX6SL                           policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX6SLL                          policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX6SX                           policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX6UL                           policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX7D                            policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX7ULP                          policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX8DXL                          policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_IMX8MM                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX8MN                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX8MP                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX8MQ                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_IMX8QM                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_IMX8QXP                          policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_IMX8ULP                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PINCTRL_IMX_SCU                          policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_INTEL                            policy<{'amd64': 'y'}>
+CONFIG_PINCTRL_IPQ4019                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_IPQ6018                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_IPQ8064                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_IPQ8074                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_IPROC_GPIO                       policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_JASPERLAKE                       policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_KEEMBAY                          policy<{'arm64': 'm'}>
+CONFIG_PINCTRL_LAKEFIELD                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_LEWISBURG                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_LOCHNAGAR                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_LPASS_LPI                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_LYNXPOINT                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_MADERA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_MAX77620                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_MCP23S08                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_MCP23S08_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_MCP23S08_SPI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_MDM9607                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MDM9615                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MESON                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MESON8                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MESON8B                          policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MESON8_PMX                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MESON_A1                         policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MESON_AXG                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MESON_AXG_PMX                    policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MESON_G12A                       policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MESON_GXBB                       policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MESON_GXL                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MICROCHIP_SGPIO                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_MSM                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MSM8226                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8660                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8916                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8953                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8960                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8976                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8994                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8996                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8998                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MSM8X74                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_MT2701                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MT2712                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT6397                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MT6765                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT6779                           policy<{'arm64': 'm'}>
+CONFIG_PINCTRL_MT6797                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT7622                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT7623                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MT7629                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MT8127                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MT8135                           policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_MT8167                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT8173                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT8183                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT8192                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT8195                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT8365                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MT8516                           policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MTK                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MTK_MOORE                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MTK_PARIS                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_MTK_V2                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_MVEBU                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_NPCM7XX                          policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_NS2_MUX                          policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_OCELOT                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_OWL                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_PALMAS                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_PFC_EMEV2                        policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7740                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7742                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7743                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7744                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7745                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77470                     policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A774A1                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A774B1                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A774C0                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A774E1                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7778                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7779                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7790                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7791                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7792                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7793                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A7794                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77950                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77951                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77960                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77961                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77965                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77970                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77980                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77990                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A77995                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_R8A779A0                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_PFC_SH73A0                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_QCOM_SPMI_PMIC                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_QCOM_SSBI_PMIC                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_QCS404                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_QDF2XXX                          policy<{'arm64': 'm'}>
+CONFIG_PINCTRL_RENESAS                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_RK805                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_ROCKCHIP                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_RZA1                             policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_RZA2                             policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_RZG2L                            policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_RZN1                             policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_S500                             policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_S700                             policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_S900                             policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SAMSUNG                          policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_SC7180                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SC7280                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SC8180X                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SDM660                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SDM845                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SDX55                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SH_PFC                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PINCTRL_SH_PFC_GPIO                      policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_SINGLE                           policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_SM6115                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SM6125                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SM8150                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SM8250                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SM8350                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PINCTRL_SPRD                             policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SPRD_SC9860                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_STMFX                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINCTRL_SUN4I_A10                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_A100                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_A100_R                    policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_A64                       policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_A64_R                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_H5                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_H6                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_H616                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_H616_R                    policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN50I_H6_R                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN5I                            policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN6I_A31                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN6I_A31_R                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_A23                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_A23_R                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_A33                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_A83T                       policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_A83T_R                     policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_H3                         policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_H3_R                       policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN8I_V3S                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN9I_A80                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUN9I_A80_R                      policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SUNRISEPOINT                     policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_SUNXI                            policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_SX150X                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PINCTRL_TEGRA                            policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_TEGRA114                         policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_TEGRA124                         policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_TEGRA194                         policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_TEGRA20                          policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_TEGRA210                         policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_TEGRA30                          policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_TEGRA_XUSB                       policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_PINCTRL_TIGERLAKE                        policy<{'amd64': 'm'}>
+CONFIG_PINCTRL_TI_IODELAY                       policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_TMPV7700                         policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_UNIPHIER                         policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_LD11                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_LD20                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_LD4                     policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_LD6B                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_PRO4                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_PRO5                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_PXS2                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_PXS3                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_UNIPHIER_SLD8                    policy<{'armhf': 'y'}>
+CONFIG_PINCTRL_VF610                            policy<{'armhf-generic': 'y'}>
+CONFIG_PINCTRL_VISCONTI                         policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_ZYNQMP                           policy<{'arm64': 'm'}>
+CONFIG_PING                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PINMUX                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PJ4B_ERRATA_4742                         policy<{'armhf': 'y'}>
+CONFIG_PKCS7_MESSAGE_PARSER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PKCS7_TEST_KEY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PKCS8_PRIVATE_KEY_PARSER                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PKEY                                     policy<{'s390x': 'm'}>
+CONFIG_PL310_ERRATA_588369                      policy<{'armhf': 'y'}>
+CONFIG_PL310_ERRATA_727915                      policy<{'armhf': 'y'}>
+CONFIG_PL310_ERRATA_753970                      policy<{'armhf': 'y'}>
+CONFIG_PL310_ERRATA_769419                      policy<{'armhf': 'y'}>
+CONFIG_PL320_MBOX                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_PL330_DMA                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PL353_SMC                                policy<{'armhf': 'm'}>
+CONFIG_PLATFORM_MHU                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PLATFORM_SI4713                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PLAT_ORION                               policy<{'armhf': 'y'}>
+CONFIG_PLAT_SPEAR                               policy<{'armhf': 'n'}>
+CONFIG_PLAT_VERSATILE                           policy<{'armhf': 'y'}>
+CONFIG_PLAYSTATION_FF                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PLDMFW                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PLIP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PLX_DMA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PLX_HERMES                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PM8916_WATCHDOG                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PMBUS                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PMC_ATOM                                 policy<{'amd64': 'y'}>
+CONFIG_PMIC_ADP5520                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PMIC_DA903X                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PMIC_DA9052                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PMIC_OPREGION                            policy<{'amd64': 'y', 'arm64': 'n'}>
+CONFIG_PMS7003                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PMU_SYSFS                                policy<{'ppc64el': 'n'}>
+CONFIG_PM_ADVANCED_DEBUG                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_AUTOSLEEP                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PM_CLK                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_DEBUG                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_DEVFREQ                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PM_DEVFREQ_EVENT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_GENERIC_DOMAINS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_GENERIC_DOMAINS_OF                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_GENERIC_DOMAINS_SLEEP                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_NOTIFIER_ERROR_INJECT                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PM_OPP                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_SLEEP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_SLEEP_DEBUG                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_SLEEP_SMP                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_SLEEP_SMP_NONZERO_CPU                 policy<{'ppc64el': 'y'}>
+CONFIG_PM_STD_PARTITION                         policy<{'amd64': '""', 'armhf': '""'}>
+CONFIG_PM_TEST_SUSPEND                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PM_TRACE                                 policy<{'amd64': 'y'}>
+CONFIG_PM_TRACE_RTC                             policy<{'amd64': 'y'}>
+CONFIG_PM_WAKELOCKS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_WAKELOCKS_GC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PM_WAKELOCKS_LIMIT                       policy<{'amd64': '100', 'arm64': '100', 'armhf': '100', 'ppc64el': '100'}>
+CONFIG_PNFS_BLOCK                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PNFS_FILE_LAYOUT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PNFS_FLEXFILE_LAYOUT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PNP                                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_PNPACPI                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_PNP_DEBUG_MESSAGES                       policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_POSIX_CPU_TIMERS_TASK_WORK               policy<{'amd64': 'y'}>
+CONFIG_POSIX_MQUEUE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_POSIX_MQUEUE_SYSCTL                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_POSIX_TIMERS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_POWER7_CPU                               policy<{'ppc64el': 'n'}>
+CONFIG_POWER8_CPU                               policy<{'ppc64el': 'n'}>
+CONFIG_POWER9_CPU                               policy<{'ppc64el': 'n'}>
+CONFIG_POWERCAP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_POWERNV_CPUFREQ                          policy<{'ppc64el': 'y'}>
+CONFIG_POWERNV_CPUIDLE                          policy<{'ppc64el': 'y'}>
+CONFIG_POWERNV_OP_PANEL                         policy<{'ppc64el': 'm'}>
+CONFIG_POWER_AVS_OMAP                           policy<{'armhf-generic': 'y'}>
+CONFIG_POWER_AVS_OMAP_CLASS3                    policy<{'armhf-generic': 'y'}>
+CONFIG_POWER_CTRL_LOGIC                         policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_POWER_RESET                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_POWER_RESET_AS3722                       policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_ATC260X                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_POWER_RESET_AXXIA                        policy<{'armhf-generic-lpae': 'y'}>
+CONFIG_POWER_RESET_BRCMKONA                     policy<{'armhf': 'y'}>
+CONFIG_POWER_RESET_BRCMSTB                      policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_POWER_RESET_GPIO                         policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_GPIO_RESTART                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_HISI                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_POWER_RESET_LINKSTATION                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_POWER_RESET_LTC2952                      policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_MSM                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_POWER_RESET_MT6323                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_OCELOT_RESET                 policy<{'arm64': 'y'}>
+CONFIG_POWER_RESET_QCOM_PON                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_POWER_RESET_QNAP                         policy<{'armhf': 'n'}>
+CONFIG_POWER_RESET_REGULATOR                    policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_RESTART                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_POWER_RESET_RMOBILE                      policy<{'armhf': 'm'}>
+CONFIG_POWER_RESET_SC27XX                       policy<{'arm64': 'm'}>
+CONFIG_POWER_RESET_SYSCON                       policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_SYSCON_POWEROFF              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_TPS65086                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_POWER_RESET_VERSATILE                    policy<{'armhf': 'y'}>
+CONFIG_POWER_RESET_VEXPRESS                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_POWER_RESET_XGENE                        policy<{'arm64': 'n'}>
+CONFIG_POWER_SUPPLY                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_POWER_SUPPLY_DEBUG                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_POWER_SUPPLY_HWMON                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PPC                                      policy<{'ppc64el': 'y'}>
+CONFIG_PPC64                                    policy<{'ppc64el': 'y'}>
+CONFIG_PPC64_BOOT_WRAPPER                       policy<{'ppc64el': 'y'}>
+CONFIG_PPC64_SUPPORTS_MEMORY_FAILURE            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_4K_PAGES                             policy<{'ppc64el': 'n'}>
+CONFIG_PPC_64K_PAGES                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_BARRIER_NOSPEC                       policy<{'ppc64el': 'y'}>
+CONFIG_PPC_BOOK3E_64                            policy<{'ppc64el': 'n'}>
+CONFIG_PPC_BOOK3S                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_BOOK3S_64                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_BOOK3S_IDLE                          policy<{'ppc64el': 'y'}>
+CONFIG_PPC_COPRO_BASE                           policy<{'ppc64el': 'y'}>
+CONFIG_PPC_DAWR                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_DENORMALISATION                      policy<{'ppc64el': 'y'}>
+CONFIG_PPC_DISABLE_WERROR                       policy<{'ppc64el': 'n'}>
+CONFIG_PPC_DOORBELL                             policy<{'ppc64el': 'y'}>
+CONFIG_PPC_DT_CPU_FTRS                          policy<{'ppc64el': 'y'}>
+CONFIG_PPC_EARLY_DEBUG                          policy<{'ppc64el': 'n'}>
+CONFIG_PPC_EMULATED_STATS                       policy<{'ppc64el': 'n'}>
+CONFIG_PPC_EPAPR_HV_BYTECHAN                    policy<{'ppc64el': 'n'}>
+CONFIG_PPC_FAST_ENDIAN_SWITCH                   policy<{'ppc64el': 'n'}>
+CONFIG_PPC_FPU                                  policy<{'ppc64el': 'y'}>
+CONFIG_PPC_FPU_REGS                             policy<{'ppc64el': 'y'}>
+CONFIG_PPC_HAVE_KUAP                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_HAVE_KUEP                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_HAVE_PMU_SUPPORT                     policy<{'ppc64el': 'y'}>
+CONFIG_PPC_I8259                                policy<{'ppc64el': 'y'}>
+CONFIG_PPC_ICP_HV                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_ICP_NATIVE                           policy<{'ppc64el': 'y'}>
+CONFIG_PPC_ICS_RTAS                             policy<{'ppc64el': 'y'}>
+CONFIG_PPC_INDIRECT_PIO                         policy<{'ppc64el': 'y'}>
+CONFIG_PPC_IRQ_SOFT_MASK_DEBUG                  policy<{'ppc64el': 'n'}>
+CONFIG_PPC_KUAP                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_KUAP_DEBUG                           policy<{'ppc64el': 'n'}>
+CONFIG_PPC_KUEP                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_MEMTRACE                             policy<{'ppc64el': 'y'}>
+CONFIG_PPC_MM_SLICES                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_MSI_BITMAP                           policy<{'ppc64el': 'y'}>
+CONFIG_PPC_NATIVE                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_OF_BOOT_TRAMPOLINE                   policy<{'ppc64el': 'y'}>
+CONFIG_PPC_P7_NAP                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_PAGE_SHIFT                           policy<{'ppc64el': '16'}>
+CONFIG_PPC_PERF_CTRS                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_PKEY                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_POWERNV                              policy<{'ppc64el': 'y'}>
+CONFIG_PPC_PROT_SAO_LPAR                        policy<{'ppc64el': 'n'}>
+CONFIG_PPC_PSERIES                              policy<{'ppc64el': 'y'}>
+CONFIG_PPC_QUEUED_SPINLOCKS                     policy<{'ppc64el': 'n'}>
+CONFIG_PPC_RADIX_MMU                            policy<{'ppc64el': 'y'}>
+CONFIG_PPC_RADIX_MMU_DEFAULT                    policy<{'ppc64el': 'y'}>
+CONFIG_PPC_RFI_SRR_DEBUG                        policy<{'ppc64el': 'n'}>
+CONFIG_PPC_RTAS                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_RTAS_DAEMON                          policy<{'ppc64el': 'y'}>
+CONFIG_PPC_RTAS_FILTER                          policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SMLPAR                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SMP_MUXED_IPI                        policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SPLPAR                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SUBPAGE_PROT                         policy<{'ppc64el': 'y'}>
+CONFIG_PPC_SVM                                  policy<{'ppc64el': 'y'}>
+CONFIG_PPC_TRANSACTIONAL_MEM                    policy<{'ppc64el': 'y'}>
+CONFIG_PPC_UDBG_16550                           policy<{'ppc64el': 'y'}>
+CONFIG_PPC_UV                                   policy<{'ppc64el': 'y'}>
+CONFIG_PPC_VAS                                  policy<{'ppc64el': 'y'}>
+CONFIG_PPC_WATCHDOG                             policy<{'ppc64el': 'y'}>
+CONFIG_PPC_WERROR                               policy<{'ppc64el': 'y'}>
+CONFIG_PPC_XICS                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_XIVE                                 policy<{'ppc64el': 'y'}>
+CONFIG_PPC_XIVE_NATIVE                          policy<{'ppc64el': 'y'}>
+CONFIG_PPC_XIVE_SPAPR                           policy<{'ppc64el': 'y'}>
+CONFIG_PPDEV                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPP                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PPPOATM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPPOE                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPPOL2TP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPP_ASYNC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPP_BSDCOMP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPP_DEFLATE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPP_FILTER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PPP_MPPE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPP_MULTILINK                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PPP_SYNC_TTY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPS                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_PPS_CLIENT_GPIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PPS_CLIENT_KTIMER                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PPS_CLIENT_LDISC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PPS_CLIENT_PARPORT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PPS_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PPTP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PREEMPT                                  policy<{'amd64': 'n', 'amd64-lowlatency': 'y', 'arm64': 'n', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PREEMPTION                               policy<{'amd64-lowlatency': 'y', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y'}>
+CONFIG_PREEMPTIRQ_DELAY_TEST                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PREEMPT_COUNT                            policy<{'amd64-lowlatency': 'y', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y'}>
+CONFIG_PREEMPT_DYNAMIC                          policy<{'amd64-lowlatency': 'y'}>
+CONFIG_PREEMPT_NOTIFIERS                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PREEMPT_RCU                              policy<{'amd64-lowlatency': 'y', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y'}>
+CONFIG_PREEMPT_TRACER                           policy<{'amd64-lowlatency': 'n', 'arm64-lowlatency': 'n', 'arm64-lowlatency-64k': 'n'}>
+CONFIG_PREEMPT_VOLUNTARY                        policy<{'amd64': 'y', 'amd64-lowlatency': 'n', 'arm64': 'y', 'arm64-lowlatency': 'n', 'arm64-lowlatency-64k': 'n', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PRESTERA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PRESTERA_PCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PREVENT_FIRMWARE_BUILD                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PRIME_NUMBERS                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PRINTER                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PRINTK                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PRINTK_CALLER                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PRINTK_INDEX                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT                policy<{'amd64': '13', 'arm64': '13', 'armhf': '13', 'ppc64el': '13', 's390x': '13'}>
+CONFIG_PRINTK_TIME                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PRINT_QUOTA_WARNING                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PRINT_STACK_DEPTH                        policy<{'ppc64el': '64'}>
+CONFIG_PRISM2_USB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PROBE_EVENTS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROCESSOR_SELECT                         policy<{'amd64': 'y'}>
+CONFIG_PROC_CHILDREN                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_CPU_RESCTRL                         policy<{'amd64': 'y'}>
+CONFIG_PROC_EVENTS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_FS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_KCORE                               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_MEM_ALWAYS_FORCE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_MEM_FORCE_PTRACE                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PROC_MEM_NO_FORCE                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PROC_PAGE_MONITOR                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_PID_ARCH_STATUS                     policy<{'amd64': 'y'}>
+CONFIG_PROC_PID_CPUSET                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_SYSCTL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_THERMAL_MMIO_RAPL                   policy<{'amd64': 'm'}>
+CONFIG_PROC_VMCORE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROC_VMCORE_DEVICE_DUMP                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROFILE_ANNOTATED_BRANCHES               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PROFILING                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PROTECTED_VIRTUALIZATION_GUEST           policy<{'s390x': 'y'}>
+CONFIG_PROVE_LOCKING                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_PROVIDE_OHCI1394_DMA_INIT                policy<{'amd64': 'n'}>
+CONFIG_PRU_REMOTEPROC                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PSAMPLE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PSERIES_CPUIDLE                          policy<{'ppc64el': 'y'}>
+CONFIG_PSERIES_ENERGY                           policy<{'ppc64el': 'm'}>
+CONFIG_PSI                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PSTORE                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PSTORE_842_COMPRESS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PSTORE_BLK                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PSTORE_BLK_BLKDEV                        policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""'}>
+CONFIG_PSTORE_BLK_CONSOLE_SIZE                  policy<{'armhf': '64'}>
+CONFIG_PSTORE_BLK_KMSG_SIZE                     policy<{'amd64': '64', 'arm64': '64', 'armhf': '64', 'ppc64el': '64'}>
+CONFIG_PSTORE_BLK_MAX_REASON                    policy<{'amd64': '2', 'arm64': '2', 'armhf': '2', 'ppc64el': '2'}>
+CONFIG_PSTORE_COMPRESS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PSTORE_COMPRESS_DEFAULT                  policy<{'amd64': '"deflate"', 'arm64': '"deflate"', 'armhf': '"deflate"', 'ppc64el': '"deflate"'}>
+CONFIG_PSTORE_CONSOLE                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'y', 'ppc64el': 'n'}>
+CONFIG_PSTORE_DEFAULT_KMSG_BYTES                policy<{'amd64': '10240', 'arm64': '10240', 'armhf': '10240', 'ppc64el': '10240'}>
+CONFIG_PSTORE_DEFLATE_COMPRESS                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PSTORE_DEFLATE_COMPRESS_DEFAULT          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PSTORE_FTRACE                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PSTORE_LZ4HC_COMPRESS                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PSTORE_LZ4_COMPRESS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PSTORE_LZO_COMPRESS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PSTORE_PMSG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PSTORE_RAM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_PSTORE_ZONE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PSTORE_ZSTD_COMPRESS                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PTDUMP_CORE                              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_PTDUMP_DEBUGFS                           policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_PTP_1588_CLOCK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_PTP_1588_CLOCK_DTE                       policy<{'arm64': 'm'}>
+CONFIG_PTP_1588_CLOCK_IDT82P33                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_PTP_1588_CLOCK_IDTCM                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PTP_1588_CLOCK_INES                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_PTP_1588_CLOCK_KVM                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PTP_1588_CLOCK_OCP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PTP_1588_CLOCK_OPTIONAL                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_PTP_1588_CLOCK_QORIQ                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PTP_1588_CLOCK_VMW                       policy<{'amd64': 'm'}>
+CONFIG_PUNIT_ATOM_DEBUG                         policy<{'amd64': 'm'}>
+CONFIG_PVH                                      policy<{'amd64': 'y'}>
+CONFIG_PVPANIC                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PVPANIC_MMIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PVPANIC_PCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_PWM_ATMEL_HLCDC_PWM                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_ATMEL_TCB                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_BCM2835                              policy<{'arm64': 'm'}>
+CONFIG_PWM_BCM_IPROC                            policy<{'arm64': 'm'}>
+CONFIG_PWM_BERLIN                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_BRCMSTB                              policy<{'arm64': 'm'}>
+CONFIG_PWM_CRC                                  policy<{'amd64': 'y'}>
+CONFIG_PWM_CROS_EC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_PWM_DWC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_FSL_FTM                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_HIBVT                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_IMX1                                 policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PWM_IMX27                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PWM_IMX_TPM                              policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PWM_IQS620A                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_KEEMBAY                              policy<{'arm64': 'm'}>
+CONFIG_PWM_LP3943                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_LPSS                                 policy<{'amd64': 'y'}>
+CONFIG_PWM_LPSS_PCI                             policy<{'amd64': 'y'}>
+CONFIG_PWM_LPSS_PLATFORM                        policy<{'amd64': 'y'}>
+CONFIG_PWM_MEDIATEK                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_MESON                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_MTK_DISP                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_NTXEC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_OMAP_DMTIMER                         policy<{'armhf': 'm'}>
+CONFIG_PWM_PCA9685                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_RASPBERRYPI_POE                      policy<{'arm64': 'm'}>
+CONFIG_PWM_RCAR                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_RENESAS_TPU                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_ROCKCHIP                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_PWM_SAMSUNG                              policy<{'armhf': 'm'}>
+CONFIG_PWM_SL28CPLD                             policy<{'arm64': 'm'}>
+CONFIG_PWM_SPRD                                 policy<{'arm64': 'm'}>
+CONFIG_PWM_STMPE                                policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PWM_SUN4I                                policy<{'arm64': 'm'}>
+CONFIG_PWM_SYSFS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_PWM_TEGRA                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_PWM_TIECAP                               policy<{'arm64': 'm', 'armhf-generic': 'm', 'armhf-generic-lpae': 'n'}>
+CONFIG_PWM_TIEHRPWM                             policy<{'arm64': 'm', 'armhf-generic': 'm', 'armhf-generic-lpae': 'n'}>
+CONFIG_PWM_TWL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_TWL_LED                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWM_VISCONTI                             policy<{'arm64': 'm'}>
+CONFIG_PWRSEQ_EMMC                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWRSEQ_SD8787                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PWRSEQ_SIMPLE                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_PXA168_ETH                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCA7000                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCA7000_SPI                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCA7000_UART                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_A53PLL                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_A7PLL                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_ADM                                 policy<{'armhf-generic': 'm'}>
+CONFIG_QCOM_AOSS_QMP                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_APCS_IPC                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_APR                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_BAM_DMA                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_CLK_APCC_MSM8996                    policy<{'arm64': 'm'}>
+CONFIG_QCOM_CLK_APCS_MSM8916                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_CLK_APCS_SDX55                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_CLK_RPM                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_CLK_RPMH                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_CLK_SMD_RPM                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_COINCELL                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_COMMAND_DB                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_CPR                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_EBI2                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_EMAC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_FALKOR_ERRATUM_1003                 policy<{'arm64': 'y'}>
+CONFIG_QCOM_FALKOR_ERRATUM_1009                 policy<{'arm64': 'y'}>
+CONFIG_QCOM_FALKOR_ERRATUM_E1041                policy<{'arm64': 'y'}>
+CONFIG_QCOM_FASTRPC                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_GDSC                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_GENI_SE                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_GPI_DMA                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_GSBI                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_HFPLL                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_HIDMA                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_HIDMA_MGMT                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_IOMMU                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_IPA                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_IPCC                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_IRQ_COMBINER                        policy<{'arm64': 'y'}>
+CONFIG_QCOM_KRYO_L2_ACCESSORS                   policy<{'arm64': 'y'}>
+CONFIG_QCOM_L2_PMU                              policy<{'arm64': 'y'}>
+CONFIG_QCOM_L3_PMU                              policy<{'arm64': 'y'}>
+CONFIG_QCOM_LLCC                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_LMH                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_MDT_LOADER                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_OCMEM                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_PDC                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_PDR_HELPERS                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_PIL_INFO                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_PM8XXX_XOADC                        policy<{'armhf': 'm'}>
+CONFIG_QCOM_Q6V5_ADSP                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_Q6V5_COMMON                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_Q6V5_MSS                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_Q6V5_PAS                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_Q6V5_WCSS                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_QFPROM                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_QMI_HELPERS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_RMTFS_MEM                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_RPMCC                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_RPMH                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_RPMHPD                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_RPMPD                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_RPROC_COMMON                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SCM                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_QCOM_SMD_RPM                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SMEM                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SMEM_STATE                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_QCOM_SMP2P                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SMSM                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SOCINFO                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SPMI_ADC5                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_SPMI_ADC_TM5                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SPMI_IADC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_SPMI_TEMP_ALARM                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_SPMI_VADC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_SYSMON                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_TSENS                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_VADC_COMMON                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QCOM_WCNSS_CTRL                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCOM_WCNSS_PIL                           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_QCOM_WDT                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCS_GCC_404                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCS_Q6SSTOP_404                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QCS_TURING_404                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_QDIO                                     policy<{'s390x': 'm'}>
+CONFIG_QED                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QEDE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QEDF                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QEDI                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QED_FCOE                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QED_ISCSI                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QED_LL2                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QED_OOO                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QED_RDMA                                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_QED_SRIOV                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QETH                                     policy<{'s390x': 'm'}>
+CONFIG_QETH_L2                                  policy<{'s390x': 'm'}>
+CONFIG_QETH_L3                                  policy<{'s390x': 'm'}>
+CONFIG_QE_GPIO                                  policy<{'ppc64el': 'y'}>
+CONFIG_QE_TDM                                   policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QE_USB                                   policy<{'ppc64el': 'y'}>
+CONFIG_QFMT_V1                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_QFMT_V2                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_QLA3XXX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QLCNIC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QLCNIC_DCB                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QLCNIC_HWMON                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QLCNIC_SRIOV                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QLGE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QNX4FS_FS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_QNX6FS_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_QNX6FS_FS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_QORIQ_CPUFREQ                            policy<{'arm64': 'm'}>
+CONFIG_QORIQ_THERMAL                            policy<{'arm64': 'm'}>
+CONFIG_QRTR                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_QRTR_MHI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QRTR_SMD                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QRTR_TUN                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QSEMI_PHY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_QTNFMAC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QTNFMAC_PCIE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_QUEUED_RWLOCKS                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_QUEUED_SPINLOCKS                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_QUICC_ENGINE                             policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_QUOTA                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_QUOTACTL                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_QUOTA_DEBUG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_QUOTA_NETLINK_INTERFACE                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_QUOTA_TREE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_R6040                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_R8169                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_R8188EU                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_R8712U                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_ADAPTERS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RADIO_MAXIRADIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_SAA7706H                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_SHARK                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_SHARK2                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_SI470X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_SI4713                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_SI476X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_TEA575X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_TEA5764                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_TEF6862                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_WL1273                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RADIO_WL128X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAID6_PQ                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RAID6_PQ_BENCHMARK                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RAID_ATTRS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RANDOM32_SELFTEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RANDOMIZE_BASE                           policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT          policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_RANDOMIZE_MEMORY                         policy<{'amd64': 'y'}>
+CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING        policy<{'amd64': '0xa'}>
+CONFIG_RANDOMIZE_MODULE_REGION_FULL             policy<{'arm64': 'y'}>
+CONFIG_RANDOM_TRUST_BOOTLOADER                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RANDOM_TRUST_CPU                         policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RAPIDIO                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_RAPIDIO_CHMAN                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_CPS_GEN2                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_CPS_XX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RAPIDIO_DISC_TIMEOUT                     policy<{'amd64': '30', 'arm64': '30', 'armhf': '30', 'ppc64el': '30'}>
+CONFIG_RAPIDIO_DMA_ENGINE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RAPIDIO_ENUM_BASIC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_MPORT_CDEV                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_RXS_GEN3                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_TSI568                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_TSI57X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAPIDIO_TSI721                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RAS                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RASPBERRYPI_FIRMWARE                     policy<{'arm64': 'y'}>
+CONFIG_RASPBERRYPI_POWER                        policy<{'arm64': 'y'}>
+CONFIG_RAS_CEC                                  policy<{'amd64': 'y'}>
+CONFIG_RAS_CEC_DEBUG                            policy<{'amd64': 'n'}>
+CONFIG_RATIONAL                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RAVB                                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RAVE_SP_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_RAVE_SP_EEPROM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RAVE_SP_WATCHDOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RBTREE_TEST                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RCAR_DMAC                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RCAR_GEN3_THERMAL                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RCAR_GYRO_ADC                            policy<{'armhf': 'm'}>
+CONFIG_RCAR_THERMAL                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RCU_EQS_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RCU_EXPERT                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RCU_NEED_SEGCBLIST                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RCU_REF_SCALE_TEST                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RCU_SCALE_TEST                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RCU_STALL_COMMON                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RCU_TORTURE_TEST                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RCU_TRACE                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RC_ATI_REMOTE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RC_CORE                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_RC_DECODERS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RC_DEVICES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RC_LOOPBACK                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RC_MAP                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RC_XBOX_DVD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RDA_INTC                                 policy<{'armhf': 'y'}>
+CONFIG_RDA_TIMER                                policy<{'armhf': 'y'}>
+CONFIG_RDMA_RXE                                 policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RDMA_SIW                                 policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RDS                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RDS_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RDS_RDMA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RDS_TCP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RD_BZIP2                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RD_GZIP                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RD_LZ4                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RD_LZMA                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RD_LZO                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RD_XZ                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RD_ZSTD                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_READABLE_ASM                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_READ_ONLY_THP_FOR_FS                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf-generic-lpae': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_REALTEK_AUTOPM                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REALTEK_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_REBOOT_MODE                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REED_SOLOMON                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_REED_SOLOMON_DEC16                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REED_SOLOMON_DEC8                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REED_SOLOMON_ENC8                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REED_SOLOMON_TEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_REGMAP                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REGMAP_AC97                              policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_REGMAP_I2C                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REGMAP_I3C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_IRQ                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REGMAP_MMIO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REGMAP_SCCB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_SLIMBUS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_SOUNDWIRE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_SOUNDWIRE_MBQ                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_SPI                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REGMAP_SPI_AVMM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_SPMI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGMAP_W1                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_REGULATOR_88PG86X                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_88PM800                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_88PM8607                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_AAT2870                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ACT8865                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ACT8945A                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_AD5398                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ANATOP                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_REGULATOR_ARIZONA_LDO1                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ARIZONA_MICSUPP                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ARM_SCMI                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_AS3711                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_AS3722                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ATC260X                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_AXP20X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_BCM590XX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_BD71815                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_BD71828                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_BD718XX                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_BD9571MWV                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_BD957XMUF                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_CPCAP                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_CROS_EC                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_DA903X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9052                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9055                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9062                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9063                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9121                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9210                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DA9211                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_REGULATOR_FAN53555                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_FAN53880                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_GPIO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_HI6421                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_HI6421V530                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_HI6421V600                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_HI655X                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_ISL6271A                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ISL9305                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LM363X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LOCHNAGAR                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP3971                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP3972                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP872X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP873X                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP8755                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP87565                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LP8788                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LTC3589                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_LTC3676                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX14577                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX1586                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX77620                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX77650                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX77686                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX77693                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX77802                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX77826                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8649                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8660                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8893                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8907                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8925                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8952                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8973                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8997                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MAX8998                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MC13783                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MC13892                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MC13XXX_CORE                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MCP16502                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MP5416                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MP8859                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MP886X                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MPQ7920                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6311                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6315                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6323                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6358                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6359                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6360                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_MT6380                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_MT6397                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PALMAS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PBIAS                          policy<{'armhf': 'm'}>
+CONFIG_REGULATOR_PCA9450                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PCAP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PCF50633                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PF8X00                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PFUZE100                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PV88060                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PV88080                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PV88090                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_PWM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_QCOM_LABIBB                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_QCOM_RPM                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_QCOM_RPMH                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_QCOM_SMD_RPM                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_QCOM_SPMI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_QCOM_USB_VBUS                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RC5T583                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RK808                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RN5T618                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_ROHM                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RT4801                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RT4831                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RT5033                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RT6160                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RT6245                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RTMV20                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RTQ2134                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_RTQ6752                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_S2MPA01                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_S2MPS11                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_S5M8767                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_SC2731                         policy<{'arm64': 'm'}>
+CONFIG_REGULATOR_SKY81452                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_SLG51000                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_STPMIC1                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_SY8106A                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_SY8824X                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_SY8827N                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TI_ABB                         policy<{'armhf': 'y'}>
+CONFIG_REGULATOR_TPS51632                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS6105X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS62360                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65023                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS6507X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65086                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65090                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65132                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65218                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS6524X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS6586X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65910                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS65912                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_TPS80031                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_UNIPHIER                       policy<{'armhf': 'm'}>
+CONFIG_REGULATOR_USERSPACE_CONSUMER             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_VCTRL                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_VEXPRESS                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_VIRTUAL_CONSUMER               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_VQMMC_IPQ4019                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_REGULATOR_WM831X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_WM8350                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_WM8400                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REGULATOR_WM8994                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_REISERFS_CHECK                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_REISERFS_FS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_REISERFS_FS_POSIX_ACL                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REISERFS_FS_SECURITY                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REISERFS_FS_XATTR                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_REISERFS_PROC_INFO                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RELAY                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RELOCATABLE                              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RELOCATABLE_TEST                         policy<{'ppc64el': 'n'}>
+CONFIG_REMOTEPROC                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_REMOTEPROC_CDEV                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RENESAS_DMA                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RENESAS_INTC_IRQPIN                      policy<{'armhf': 'y'}>
+CONFIG_RENESAS_IRQC                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RENESAS_OSTM                             policy<{'armhf': 'y'}>
+CONFIG_RENESAS_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RENESAS_RPCIF                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RENESAS_RZA1_IRQC                        policy<{'armhf': 'y'}>
+CONFIG_RENESAS_RZAWDT                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RENESAS_USB_DMAC                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RENESAS_WDT                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RESET_A10SR                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RESET_ATTACK_MITIGATION                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RESET_BERLIN                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RESET_BRCMSTB                            policy<{'arm64': 'm'}>
+CONFIG_RESET_BRCMSTB_RESCAL                     policy<{'arm64': 'y'}>
+CONFIG_RESET_CONTROLLER                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_RESET_HISI                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RESET_IMX7                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_RESET_MCHP_SPARX5                        policy<{'arm64': 'y'}>
+CONFIG_RESET_MESON                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RESET_MESON_AUDIO_ARB                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RESET_NPCM                               policy<{'armhf': 'y'}>
+CONFIG_RESET_QCOM_AOSS                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RESET_QCOM_PDC                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RESET_RASPBERRYPI                        policy<{'arm64': 'm'}>
+CONFIG_RESET_RZG2L_USBPHY_CTRL                  policy<{'arm64': 'm'}>
+CONFIG_RESET_SCMI                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RESET_SIMPLE                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RESET_SOCFPGA                            policy<{'armhf': 'y'}>
+CONFIG_RESET_SUNXI                              policy<{'arm64': 'y'}>
+CONFIG_RESET_TEGRA_BPMP                         policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_RESET_TI_SCI                             policy<{'arm64': 'm'}>
+CONFIG_RESET_TI_SYSCON                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RESET_UNIPHIER                           policy<{'armhf': 'm'}>
+CONFIG_RESET_UNIPHIER_GLUE                      policy<{'armhf': 'm'}>
+CONFIG_RETHUNK                                  policy<{'amd64': 'y'}>
+CONFIG_RETPOLINE                                policy<{'amd64': 'y'}>
+CONFIG_RETU_WATCHDOG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RFD77402                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RFD_FTL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RFKILL                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_RFKILL_GPIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RFKILL_INPUT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RFKILL_LEDS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RFS_ACCEL                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RING_BUFFER                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RING_BUFFER_BENCHMARK                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RING_BUFFER_STARTUP_TEST                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RING_BUFFER_VALIDATE_TIME_DELTAS         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_RIONET                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RIONET_RX_SIZE                           policy<{'amd64': '128', 'arm64': '128', 'armhf': '128', 'ppc64el': '128'}>
+CONFIG_RIONET_TX_SIZE                           policy<{'amd64': '128', 'arm64': '128', 'armhf': '128', 'ppc64el': '128'}>
+CONFIG_RMI4_2D_SENSOR                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_CORE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_RMI4_F03                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F03_SERIO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RMI4_F11                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F12                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F30                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F34                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F3A                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F54                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_F55                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RMI4_I2C                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RMI4_SMB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RMI4_SPI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RMNET                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RN5T618_ADC                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RN5T618_POWER                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RN5T618_WATCHDOG                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ROCKCHIP_ANALOGIX_DP                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_CDN_DP                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_DW_HDMI                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_DW_MIPI_DSI                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_EFUSE                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ROCKCHIP_GRF                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_INNO_HDMI                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_IODOMAIN                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ROCKCHIP_IOMMU                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_LVDS                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_MBOX                            policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_OTP                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ROCKCHIP_PHY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ROCKCHIP_PM_DOMAINS                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_RGB                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_RK3066_HDMI                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKCHIP_SARADC                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ROCKCHIP_THERMAL                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_ROCKCHIP_TIMER                           policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_ROCKER                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RODATA_FULL_DEFAULT_ENABLED              policy<{'arm64': 'y'}>
+CONFIG_ROMFS_BACKED_BY_BLOCK                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ROMFS_BACKED_BY_BOTH                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ROMFS_BACKED_BY_MTD                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ROMFS_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ROMFS_ON_BLOCK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ROSE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPCSEC_GSS_KRB5                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_RPMSG                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPMSG_CHAR                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPMSG_MTK_SCP                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RPMSG_NS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPMSG_QCOM_GLINK                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPMSG_QCOM_GLINK_RPM                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPMSG_QCOM_GLINK_SMEM                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RPMSG_QCOM_SMD                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RPMSG_VIRTIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_RPMSG_WWAN_CTRL                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPR0521                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RPS                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RSEQ                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RSI_91X                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RSI_COEX                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RSI_DEBUGFS                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RSI_SDIO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RSI_USB                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RST_RCAR                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RT2400PCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2500PCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2500USB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2800PCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2800PCI_RT3290                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800PCI_RT33XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800PCI_RT35XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800PCI_RT53XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800USB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2800USB_RT33XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800USB_RT3573                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800USB_RT35XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800USB_RT53XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800USB_RT55XX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800USB_UNKNOWN                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2800_LIB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2800_LIB_MMIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2X00                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2X00_DEBUG                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RT2X00_LIB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2X00_LIB_CRYPTO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2X00_LIB_DEBUGFS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RT2X00_LIB_FIRMWARE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2X00_LIB_LEDS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RT2X00_LIB_MMIO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2X00_LIB_PCI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT2X00_LIB_USB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT61PCI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT73USB                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTAS_ERROR_LOGGING                       policy<{'ppc64el': 'y'}>
+CONFIG_RTAS_FLASH                               policy<{'ppc64el': 'm'}>
+CONFIG_RTAS_PROC                                policy<{'ppc64el': 'y'}>
+CONFIG_RTC_CLASS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_DRV_88PM80X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_88PM860X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ABB5ZES3                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ABEOZ9                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ABX80X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ARMADA38X                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_AS3722                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ASPEED                           policy<{'armhf': 'm'}>
+CONFIG_RTC_DRV_BD70528                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_BQ32K                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_BQ4802                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_BRCMSTB                          policy<{'arm64': 'm'}>
+CONFIG_RTC_DRV_CADENCE                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_CPCAP                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_CROS_EC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_DA9052                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DA9055                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DA9063                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1286                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1302                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1305                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1307                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1307_CENTURY                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DRV_DS1343                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1347                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1374                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1374_WDT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DRV_DS1390                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1511                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1553                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1672                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1685                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DRV_DS1685_FAMILY                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS1689                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_DRV_DS17285                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_DRV_DS1742                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS17485                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_DRV_DS17885                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_DRV_DS2404                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS3232                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_DS3232_HWMON                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DRV_EM3027                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_FM3130                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_FSL_FTM_ALARM                    policy<{'arm64': 'm'}>
+CONFIG_RTC_DRV_FTRTC010                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_GENERIC                          policy<{'ppc64el': 'y'}>
+CONFIG_RTC_DRV_GOLDFISH                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_HID_SENSOR_TIME                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_HYM8563                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_IMXDI                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_RTC_DRV_IMX_SC                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_RTC_DRV_ISL12022                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ISL12026                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_ISL1208                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_LP8788                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_M41T80                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_M41T80_WDT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DRV_M41T93                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_M41T94                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_M48T35                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_M48T59                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_M48T86                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX6900                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX6902                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX6916                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX77686                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX8907                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX8925                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX8997                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MAX8998                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MC13XXX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MCP795                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MESON                            policy<{'armhf': 'm'}>
+CONFIG_RTC_DRV_MESON_VRTC                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_MSM6242                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MT2712                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_MT6397                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_MT7622                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_MV                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RTC_DRV_MXC                              policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_RTC_DRV_MXC_V2                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_RTC_DRV_NTXEC                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_OMAP                             policy<{'armhf': 'y'}>
+CONFIG_RTC_DRV_OPAL                             policy<{'ppc64el': 'y'}>
+CONFIG_RTC_DRV_PALMAS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCAP                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF2123                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF2127                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF50633                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF85063                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF8523                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'y', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF85263                         policy<{'amd64': 'm'}>
+CONFIG_RTC_DRV_PCF85363                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF8563                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PCF8583                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_PL030                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_PL031                            policy<{'arm64': 'm', 'armhf': 'y'}>
+CONFIG_RTC_DRV_PM8XXX                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_R7301                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_R9701                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RC5T583                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RC5T619                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RK808                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RP5C01                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RS5C348                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RS5C372                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RTD119X                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RTC_DRV_RV3028                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RV3029C2                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RV3029_HWMON                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_DRV_RV3032                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RV8803                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RX4581                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RX6110                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RX8010                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RX8025                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_RX8581                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_S35390A                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_S3C                              policy<{'armhf': 'y'}>
+CONFIG_RTC_DRV_S5M                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_SC27XX                           policy<{'arm64': 'm'}>
+CONFIG_RTC_DRV_SD3078                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_SH                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_RTC_DRV_SNVS                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_RTC_DRV_STK17TA8                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_SUN6I                            policy<{'arm64': 'y'}>
+CONFIG_RTC_DRV_TEGRA                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_RTC_DRV_TEST                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_DRV_TPS6586X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_TPS65910                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_TPS80031                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_V3020                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_WILCO_EC                         policy<{'amd64': 'm'}>
+CONFIG_RTC_DRV_WM831X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_WM8350                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_X1205                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_DRV_XGENE                            policy<{'arm64': 'y'}>
+CONFIG_RTC_DRV_ZYNQMP                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTC_HCTOSYS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_HCTOSYS_DEVICE                       policy<{'amd64': '"rtc0"', 'arm64': '"rtc0"', 'armhf': '"rtc0"', 'ppc64el': '"rtc0"'}>
+CONFIG_RTC_I2C_AND_SPI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_INTF_DEV                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_INTF_DEV_UIE_EMUL                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTC_INTF_PROC                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_INTF_SYSFS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_LIB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_MC146818_LIB                         policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_NVMEM                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_SYSTOHC                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTC_SYSTOHC_DEVICE                       policy<{'amd64': '"rtc0"', 'arm64': '"rtc0"', 'armhf': '"rtc0"', 'ppc64el': '"rtc0"'}>
+CONFIG_RTD119X_WATCHDOG                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_RTL8180                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8187                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8187_LEDS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTL8188EE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192CE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192CU                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192C_COMMON                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192DE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192E                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192EE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192SE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8192U                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8723AE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8723BE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8723BS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8723_COMMON                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8821AE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8XXXU                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL8XXXU_UNTESTED                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTLBTCOEXIST                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLLIB                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLLIB_CRYPTO_CCMP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLLIB_CRYPTO_TKIP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLLIB_CRYPTO_WEP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLWIFI                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLWIFI_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_RTLWIFI_PCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTLWIFI_USB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTL_CARDS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTS5208                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8723D                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8723DE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8821C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8821CE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8822B                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8822BE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8822C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_8822CE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW88_DEBUG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTW88_DEBUGFS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTW88_PCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW89                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW89_8852AE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW89_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RTW89_DEBUG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTW89_DEBUGFS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTW89_DEBUGMSG                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_RTW89_PCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_RT_MUTEXES                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RUNTIME_TESTING_MENU                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RWSEM_SPIN_ON_OWNER                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RXKAD                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_RZG2L_ADC                                policy<{'arm64': 'm'}>
+CONFIG_RZ_DMAC                                  policy<{'arm64': 'm'}>
+CONFIG_S2IO                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_S390                                     policy<{'s390x': 'y'}>
+CONFIG_S390_AP_IOMMU                            policy<{'s390x': 'y'}>
+CONFIG_S390_CCW_IOMMU                           policy<{'s390x': 'y'}>
+CONFIG_S390_GUEST                               policy<{'s390x': 'y'}>
+CONFIG_S390_HYPFS_FS                            policy<{'s390x': 'y'}>
+CONFIG_S390_IOMMU                               policy<{'s390x': 'y'}>
+CONFIG_S390_PRNG                                policy<{'s390x': 'm'}>
+CONFIG_S390_TAPE                                policy<{'s390x': 'm'}>
+CONFIG_S390_TAPE_34XX                           policy<{'s390x': 'm'}>
+CONFIG_S390_TAPE_3590                           policy<{'s390x': 'm'}>
+CONFIG_S390_UNWIND_SELFTEST                     policy<{'s390x': 'n'}>
+CONFIG_S390_VMUR                                policy<{'s390x': 'm'}>
+CONFIG_S3C2410_WATCHDOG                         policy<{'armhf': 'm'}>
+CONFIG_S5P_DEV_MFC                              policy<{'armhf': 'y'}>
+CONFIG_SAMPLES                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SAMPLE_AUXDISPLAY                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_CONFIGFS                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_FTRACE_DIRECT                     policy<{'amd64': 'm'}>
+CONFIG_SAMPLE_HW_BREAKPOINT                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SAMPLE_KDB                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SAMPLE_KFIFO                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_KOBJECT                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_KPROBES                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_LIVEPATCH                         policy<{'amd64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_QMI_CLIENT                        policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_SAMPLE_RPMSG_CLIENT                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SAMPLE_TRACE_ARRAY                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SAMPLE_TRACE_EVENTS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_VFIO_MDEV_MBOCHS                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_VFIO_MDEV_MDPY                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_VFIO_MDEV_MDPY_FB                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_VFIO_MDEV_MTTY                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMPLE_WATCHDOG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SAMSUNG_LAPTOP                           policy<{'amd64': 'm'}>
+CONFIG_SAMSUNG_MC                               policy<{'armhf': 'y'}>
+CONFIG_SAMSUNG_Q10                              policy<{'amd64': 'm'}>
+CONFIG_SATA_ACARD_AHCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_AHCI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_AHCI_SEATTLE                        policy<{'arm64': 'm'}>
+CONFIG_SATA_DWC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_DWC_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SATA_DWC_OLD_DMA                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SATA_HOST                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SATA_INIC162X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_MOBILE_LPM_POLICY                   policy<{'amd64': '3', 'arm64': '3', 'armhf': '3', 'ppc64el': '3'}>
+CONFIG_SATA_MV                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_NV                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_PMP                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SATA_PROMISE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_QSTOR                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_RCAR                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SATA_SIL                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_SIL24                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_SIS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_SVW                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_SX4                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_ULI                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_VIA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_VITESSE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SATA_ZPODD                               policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SBC_EPX_C3_WATCHDOG                      policy<{'amd64': 'm'}>
+CONFIG_SBC_FITPC2_WATCHDOG                      policy<{'amd64': 'm'}>
+CONFIG_SBITMAP                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SBP_TARGET                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SC1200_WDT                               policy<{'amd64': 'm'}>
+CONFIG_SC27XX_ADC                               policy<{'arm64': 'm'}>
+CONFIG_SC27XX_EFUSE                             policy<{'arm64': 'm'}>
+CONFIG_SC92031                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCA3000                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCA3300                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCANLOG                                  policy<{'ppc64el': 'm'}>
+CONFIG_SCD30_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCD30_I2C                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCD30_SERIAL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCF_TORTURE_TEST                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SCHEDSTATS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_AUTOGROUP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_BOOK                               policy<{'s390x': 'y'}>
+CONFIG_SCHED_CORE                               policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_DEBUG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_DRAWER                             policy<{'s390x': 'y'}>
+CONFIG_SCHED_HRTICK                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_INFO                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_MC                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_SCHED_MC_PRIO                            policy<{'amd64': 'y'}>
+CONFIG_SCHED_OMIT_FRAME_POINTER                 policy<{'amd64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_SMT                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_STACK_END_CHECK                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCHED_THERMAL_PRESSURE                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SCHED_TOPOLOGY                           policy<{'s390x': 'y'}>
+CONFIG_SCHED_TRACER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCLP_CONSOLE                             policy<{'s390x': 'y'}>
+CONFIG_SCLP_TTY                                 policy<{'s390x': 'y'}>
+CONFIG_SCLP_VT220_CONSOLE                       policy<{'s390x': 'y'}>
+CONFIG_SCLP_VT220_TTY                           policy<{'s390x': 'y'}>
+CONFIG_SCM_BLOCK                                policy<{'s390x': 'm'}>
+CONFIG_SCM_BUS                                  policy<{'s390x': 'y'}>
+CONFIG_SCOM_DEBUGFS                             policy<{'ppc64el': 'y'}>
+CONFIG_SCR24X                                   policy<{'amd64': 'm'}>
+CONFIG_SCSI                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_3W_9XXX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_3W_SAS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_AACRAID                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_ACARD                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_ADVANSYS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_AIC79XX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_AIC7XXX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_AIC94XX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_AM53C974                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_ARCMSR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_BFA_FC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_BNX2X_FCOE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_BNX2_ISCSI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_BUSLOGIC                            policy<{'amd64': 'm'}>
+CONFIG_SCSI_CHELSIO_FCOE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_COMMON                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_CONSTANTS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_CXGB3_ISCSI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_CXGB4_ISCSI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_DC395x                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_DEBUG                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_DH                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_DH_ALUA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_DH_EMC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_DH_HP_SW                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_DH_RDAC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_DMA                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_DMX3191D                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_DPT_I2O                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_EFCT                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_ENCLOSURE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_ESAS2R                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_FC_ATTRS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_FDOMAIN                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_FDOMAIN_PCI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_FLASHPOINT                          policy<{'amd64': 'y'}>
+CONFIG_SCSI_HISI_SAS                            policy<{'arm64': 'm'}>
+CONFIG_SCSI_HISI_SAS_DEBUGFS_DEFAULT_ENABLE     policy<{'arm64': 'n'}>
+CONFIG_SCSI_HISI_SAS_PCI                        policy<{'arm64': 'm'}>
+CONFIG_SCSI_HPSA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_HPTIOP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_IBMVFC                              policy<{'ppc64el': 'm'}>
+CONFIG_SCSI_IBMVFC_TRACE                        policy<{'ppc64el': 'y'}>
+CONFIG_SCSI_IBMVSCSI                            policy<{'ppc64el': 'm'}>
+CONFIG_SCSI_IBMVSCSIS                           policy<{'ppc64el': 'm'}>
+CONFIG_SCSI_IMM                                 policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_INIA100                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_INITIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_IPR                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_IPS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_ISCI                                policy<{'amd64': 'm'}>
+CONFIG_SCSI_ISCSI_ATTRS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_IZIP_EPP16                          policy<{'amd64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SCSI_IZIP_SLOW_CTR                       policy<{'amd64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SCSI_LOGGING                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_LOWLEVEL                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_LOWLEVEL_PCMCIA                     policy<{'amd64': 'y'}>
+CONFIG_SCSI_LPFC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_LPFC_DEBUG_FS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SCSI_MOD                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_MPI3MR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_MPT2SAS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_MPT2SAS_MAX_SGE                     policy<{'amd64': '128', 'arm64': '128', 'armhf': '128', 'ppc64el': '128', 's390x': '128'}>
+CONFIG_SCSI_MPT3SAS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_MPT3SAS_MAX_SGE                     policy<{'amd64': '128', 'arm64': '128', 'armhf': '128', 'ppc64el': '128', 's390x': '128'}>
+CONFIG_SCSI_MVSAS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_MVSAS_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SCSI_MVSAS_TASKLET                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SCSI_MVUMI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_MYRB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_MYRS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_NETLINK                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_NSP32                               policy<{'armhf': 'm'}>
+CONFIG_SCSI_PM8001                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_PMCRAID                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_PPA                                 policy<{'amd64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_PROC_FS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_QLA_FC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_QLA_ISCSI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_QLOGIC_1280                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_SAS_ATA                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_SAS_ATTRS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_SAS_HOST_SMP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_SAS_LIBSAS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_SCAN_ASYNC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCSI_SMARTPQI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_SNIC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_SNIC_DEBUG_FS                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SCSI_SPI_ATTRS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SCSI_SRP_ATTRS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_SCSI_STEX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_SYM53C8XX_2                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS              policy<{'amd64': '16', 'arm64': '16', 'armhf': '16', 'ppc64el': '16'}>
+CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE       policy<{'amd64': '1', 'arm64': '1', 'armhf': '1', 'ppc64el': '1'}>
+CONFIG_SCSI_SYM53C8XX_MAX_TAGS                  policy<{'amd64': '64', 'arm64': '64', 'armhf': '64', 'ppc64el': '64'}>
+CONFIG_SCSI_SYM53C8XX_MMIO                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_UFSHCD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCSI_UFSHCD_PCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_UFSHCD_PLATFORM                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_UFS_BSG                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_UFS_CDNS_PLATFORM                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_UFS_CRYPTO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_UFS_DWC_TC_PCI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_UFS_DWC_TC_PLATFORM                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SCSI_UFS_EXYNOS                          policy<{'armhf': 'm'}>
+CONFIG_SCSI_UFS_HISI                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SCSI_UFS_HPB                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SCSI_UFS_MEDIATEK                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SCSI_UFS_QCOM                            policy<{'arm64': 'm', 'armhf': 'n'}>
+CONFIG_SCSI_UFS_TI_J721E                        policy<{'arm64': 'm'}>
+CONFIG_SCSI_WD719X                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SCTP_COOKIE_HMAC_MD5                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCTP_COOKIE_HMAC_SHA1                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SCTP_DBG_OBJCNT                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SCTP_DEFAULT_COOKIE_HMAC_MD5             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SCTP_DEFAULT_COOKIE_HMAC_NONE            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SCTP_DEFAULT_COOKIE_HMAC_SHA1            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SC_CAMCC_7180                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_DISPCC_7180                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_DISPCC_7280                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_GCC_7180                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_GCC_7280                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_GCC_8180X                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_GPUCC_7180                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_GPUCC_7280                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_LPASS_CORECC_7180                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_MSS_7180                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_VIDEOCC_7180                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SC_VIDEOCC_7280                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDIO_UART                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SDMA_VERBOSITY                           policy<{'amd64': 'n'}>
+CONFIG_SDM_CAMCC_845                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_DISPCC_845                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_GCC_660                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_GCC_845                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_GPUCC_660                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_GPUCC_845                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_LPASSCC_845                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_MMCC_660                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDM_VIDEOCC_845                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SDR_MAX2175                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SDR_PLATFORM_DRIVERS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SDX_GCC_55                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SD_ADC_MODULATOR                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SECCOMP                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECCOMP_CACHE_DEBUG                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECCOMP_FILTER                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECONDARY_TRUSTED_KEYRING                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECRETMEM                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SECTION_MISMATCH_WARN_ONLY               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITYFS                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_APPARMOR                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_APPARMOR_DEBUG                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECURITY_APPARMOR_HASH                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_APPARMOR_HASH_DEFAULT           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_DMESG_RESTRICT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_INFINIBAND                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_LANDLOCK                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_LOADPIN                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECURITY_LOCKDOWN_LSM                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_LOCKDOWN_LSM_EARLY              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_NETWORK                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_NETWORK_XFRM                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_PATH                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_PERF_EVENTS_RESTRICT            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SELINUX                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SELINUX_AVC_STATS               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SELINUX_BOOTPARAM               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE      policy<{'amd64': '1', 'arm64': '1', 'armhf': '1', 'ppc64el': '1', 's390x': '1'}>
+CONFIG_SECURITY_SELINUX_DEVELOP                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SELINUX_SID2STR_CACHE_SIZE      policy<{'amd64': '256', 'arm64': '256', 'armhf': '256', 'ppc64el': '256', 's390x': '256'}>
+CONFIG_SECURITY_SELINUX_SIDTAB_HASH_BITS        policy<{'amd64': '9', 'arm64': '9', 'armhf': '9', 'ppc64el': '9', 's390x': '9'}>
+CONFIG_SECURITY_SMACK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SMACK_APPEND_SIGNALS            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_SMACK_BRINGUP                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECURITY_SMACK_NETFILTER                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_TOMOYO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SECURITY_TOMOYO_ACTIVATION_TRIGGER       policy<{'amd64': '"/sbin/init"', 'arm64': '"/sbin/init"', 'armhf': '"/sbin/init"', 'ppc64el': '"/sbin/init"', 's390x': '"/sbin/init"'}>
+CONFIG_SECURITY_TOMOYO_INSECURE_BUILTIN_SETTING policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECURITY_TOMOYO_MAX_ACCEPT_ENTRY         policy<{'amd64': '2048', 'arm64': '2048', 'armhf': '2048', 'ppc64el': '2048', 's390x': '2048'}>
+CONFIG_SECURITY_TOMOYO_MAX_AUDIT_LOG            policy<{'amd64': '1024', 'arm64': '1024', 'armhf': '1024', 'ppc64el': '1024', 's390x': '1024'}>
+CONFIG_SECURITY_TOMOYO_OMIT_USERSPACE_LOADER    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SECURITY_TOMOYO_POLICY_LOADER            policy<{'amd64': '"/sbin/tomoyo-init"', 'arm64': '"/sbin/tomoyo-init"', 'armhf': '"/sbin/tomoyo-init"', 'ppc64el': '"/sbin/tomoyo-init"', 's390x': '"/sbin/tomoyo-init"'}>
+CONFIG_SECURITY_YAMA                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SELECT_MEMORY_MODEL                      policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SENSIRION_SGP30                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSIRION_SGP40                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_AAEON                            policy<{'amd64': 'm'}>
+CONFIG_SENSORS_ABITUGURU                        policy<{'amd64': 'm'}>
+CONFIG_SENSORS_ABITUGURU3                       policy<{'amd64': 'm'}>
+CONFIG_SENSORS_ACPI_POWER                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SENSORS_AD7314                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_AD7414                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_AD7418                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADC128D818                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADCXX                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1021                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1025                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1026                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1029                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1031                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1177                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1266                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM1275                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADM9240                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADS7828                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADS7871                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7310                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7410                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7411                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7462                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7470                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7475                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ADT7X10                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_AHT10                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_AMC6821                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_APDS990X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SENSORS_APPLESMC                         policy<{'amd64': 'm'}>
+CONFIG_SENSORS_AQUACOMPUTER_D5NEXT              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ARM_SCMI                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_ARM_SCPI                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_AS370                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ASB100                           policy<{'amd64': 'm'}>
+CONFIG_SENSORS_ASC7621                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ASPEED                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ATK0110                          policy<{'amd64': 'm'}>
+CONFIG_SENSORS_ATXP1                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_AXI_FAN_CONTROL                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_BEL_PFE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_BH1770                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SENSORS_BPA_RS600                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_CORETEMP                         policy<{'amd64': 'm'}>
+CONFIG_SENSORS_CORSAIR_CPRO                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_CORSAIR_PSU                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_DA9052_ADC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_DA9055                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_DELL_SMM                         policy<{'amd64': 'm'}>
+CONFIG_SENSORS_DME1737                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_DPS920AB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_DRIVETEMP                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_DS1621                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_DS620                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_EMC1403                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_EMC2103                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_EMC6W201                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_F71805F                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_F71882FG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_F75375S                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_FAM15H_POWER                     policy<{'amd64': 'm'}>
+CONFIG_SENSORS_FSCHMD                           policy<{'amd64': 'm'}>
+CONFIG_SENSORS_FSP_3Y                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_FTSTEUTATES                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_G760A                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_G762                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_GL518SM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_GL520SM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_GPIO_FAN                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_GSC                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_HDAPS                            policy<{'amd64': 'm'}>
+CONFIG_SENSORS_HIH6130                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_HMC5843                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_HMC5843_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_HMC5843_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_I5500                            policy<{'amd64': 'm'}>
+CONFIG_SENSORS_I5K_AMB                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IBMAEM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IBMPEX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IBMPOWERNV                       policy<{'ppc64el': 'm'}>
+CONFIG_SENSORS_IBM_CFFPS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IIO_HWMON                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_INA209                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_INA2XX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_INA3221                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_INSPUR_IPSPS                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_INTEL_M10_BMC_HWMON              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IR35221                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IR36021                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IR38064                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IRPS5401                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ISL29018                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ISL29028                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_ISL68137                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_IT87                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_JC42                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_K10TEMP                          policy<{'amd64': 'm'}>
+CONFIG_SENSORS_K8TEMP                           policy<{'amd64': 'm'}>
+CONFIG_SENSORS_LINEAGE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LIS3LV02D                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LIS3_I2C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SENSORS_LIS3_SPI                         policy<{'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM25066                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM3533                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM63                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM70                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM73                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM75                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM77                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM78                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM80                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM83                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM85                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM87                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM90                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM92                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM93                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM95234                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM95241                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LM95245                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LOCHNAGAR                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2945                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2947                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2947_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2947_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2978                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2978_REGULATOR                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SENSORS_LTC2990                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC2992                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC3815                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC4151                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC4215                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC4222                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC4245                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC4260                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_LTC4261                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX1111                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX127                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX15301                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX16064                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX16065                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX1619                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX16601                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX1668                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX197                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX20730                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX20751                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX31722                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX31730                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX31785                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX31790                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX34440                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX6621                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX6639                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX6642                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX6650                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX6697                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MAX8688                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MC13783_ADC                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MCP3021                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MENF21BMC_HWMON                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MLXREG_FAN                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_MP2888                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MP2975                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_MR75203                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_NCT6683                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_NCT6775                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_NCT7802                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_NCT7904                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_NPCM7XX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_NTC_THERMISTOR                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_NZXT_KRAKEN2                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_OCC_P8_I2C                       policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_SENSORS_OCC_P9_SBE                       policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_SENSORS_PC87360                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_PC87427                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_PCF8591                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_PIM4328                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_PM6764TR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_PMBUS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_POWR1220                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_PWM_FAN                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_PXE1610                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_Q54SJ108A2                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'n'}>
+CONFIG_SENSORS_RASPBERRYPI_HWMON                policy<{'arm64': 'm'}>
+CONFIG_SENSORS_RM3100                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_RM3100_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_RM3100_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SBRMI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SBTSI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SCH5627                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_SCH5636                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_SCH56XX_COMMON                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_SHT15                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SHT21                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SHT3x                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SHT4x                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SHTC1                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SIS5595                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SL28CPLD                         policy<{'arm64': 'm'}>
+CONFIG_SENSORS_SMM665                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SMSC47B397                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_SMSC47M1                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_SMSC47M192                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_SPARX5                           policy<{'arm64': 'm'}>
+CONFIG_SENSORS_STPDDC60                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_STTS751                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TC654                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TC74                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_THMC50                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TMP102                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TMP103                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TMP108                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TMP401                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TMP421                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TMP513                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TPS23861                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TPS40422                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TPS53679                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_TSL2550                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SENSORS_TSL2563                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_UCD9000                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_UCD9200                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_VEXPRESS                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_VIA686A                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_VIA_CPUTEMP                      policy<{'amd64': 'm'}>
+CONFIG_SENSORS_VT1211                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_VT8231                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83627EHF                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_W83627HF                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SENSORS_W83773G                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83781D                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83791D                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83792D                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83793                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83795                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83795_FANCTRL                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SENSORS_W83L785TS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_W83L786NG                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_WM831X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_WM8350                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_XDPE122                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SENSORS_XGENE                            policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SENSORS_ZL6100                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_8250                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_16550A_VARIANTS              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_ASPEED_VUART                 policy<{'arm64': '-', 'armhf': 'm', 'ppc64el': '-'}>
+CONFIG_SERIAL_8250_BCM2835AUX                   policy<{'arm64': 'n'}>
+CONFIG_SERIAL_8250_BCM7271                      policy<{'arm64': 'm'}>
+CONFIG_SERIAL_8250_CONSOLE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_CS                           policy<{'amd64': 'm'}>
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SERIAL_8250_DETECT_IRQ                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SERIAL_8250_DMA                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_DW                           policy<{'amd64': 'm', 'arm64': 'y', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_8250_DWLIB                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_EM                           policy<{'armhf': 'n'}>
+CONFIG_SERIAL_8250_EXAR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_8250_EXTENDED                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_FINTEK                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SERIAL_8250_FSL                          policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_LPSS                         policy<{'amd64': 'm'}>
+CONFIG_SERIAL_8250_MANY_PORTS                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_MEN_MCB                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_8250_MID                          policy<{'amd64': 'y'}>
+CONFIG_SERIAL_8250_MT6577                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_8250_NR_UARTS                     policy<{'amd64': '48', 'arm64': '48', 'armhf': '48', 'ppc64el': '48'}>
+CONFIG_SERIAL_8250_OMAP                         policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_8250_PCI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_PNP                          policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SERIAL_8250_RSA                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_RT288X                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_RUNTIME_UARTS                policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32'}>
+CONFIG_SERIAL_8250_SHARE_IRQ                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_8250_TEGRA                        policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SERIAL_8250_UNIPHIER                     policy<{'armhf': 'm'}>
+CONFIG_SERIAL_ALTERA_JTAGUART                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_ALTERA_UART                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_ALTERA_UART_BAUDRATE              policy<{'amd64': '115200', 'arm64': '115200', 'armhf': '115200', 'ppc64el': '115200'}>
+CONFIG_SERIAL_ALTERA_UART_MAXPORTS              policy<{'amd64': '4', 'arm64': '4', 'armhf': '4', 'ppc64el': '4'}>
+CONFIG_SERIAL_AMBA_PL010                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SERIAL_AMBA_PL011                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_AMBA_PL011_CONSOLE                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_ARC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_ARC_NR_PORTS                      policy<{'amd64': '1', 'arm64': '1', 'armhf': '1', 'ppc64el': '1'}>
+CONFIG_SERIAL_BCM63XX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_CONEXANT_DIGICOLOR                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_CORE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_SERIAL_CORE_CONSOLE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_EARLYCON                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_EARLYCON_ARM_SEMIHOST             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_FSL_LINFLEXUART                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_FSL_LPUART                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_ICOM                              policy<{'ppc64el': 'm'}>
+CONFIG_SERIAL_IMX                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SERIAL_IMX_CONSOLE                       policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SERIAL_IMX_EARLYCON                      policy<{'arm64': 'n', 'armhf-generic': 'n'}>
+CONFIG_SERIAL_IPOCTAL                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_JSM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_KGDB_NMI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_LANTIQ                            policy<{'amd64': 'm'}>
+CONFIG_SERIAL_LITEUART                          policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_LITEUART_MAX_PORTS                policy<{'arm64': '1', 'armhf': '1', 'ppc64el': '1'}>
+CONFIG_SERIAL_MAX3100                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_MAX310X                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_MCTRL_GPIO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_MEN_Z135                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_MESON                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_MESON_CONSOLE                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_MILBEAUT_USIO                     policy<{'armhf': 'm'}>
+CONFIG_SERIAL_MILBEAUT_USIO_PORTS               policy<{'armhf': '4'}>
+CONFIG_SERIAL_MSM                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_MSM_CONSOLE                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_MVEBU_CONSOLE                     policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_MVEBU_UART                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_NONSTANDARD                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SERIAL_OF_PLATFORM                       policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_OWL                               policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_OWL_CONSOLE                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_QCOM_GENI                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SERIAL_QCOM_GENI_CONSOLE                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_QE                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_RDA                               policy<{'armhf': 'y'}>
+CONFIG_SERIAL_RDA_CONSOLE                       policy<{'armhf': 'y'}>
+CONFIG_SERIAL_RP2                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_RP2_NR_UARTS                      policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32'}>
+CONFIG_SERIAL_SAMSUNG                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SERIAL_SAMSUNG_UARTS                     policy<{'arm64': '4', 'armhf': '4'}>
+CONFIG_SERIAL_SAMSUNG_UARTS_4                   policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_SC16IS7XX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SERIAL_SC16IS7XX_CORE                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_SC16IS7XX_I2C                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_SC16IS7XX_SPI                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_SCCNXP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SERIAL_SCCNXP_CONSOLE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIAL_SH_SCI_DMA                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SERIAL_SH_SCI_NR_UARTS                   policy<{'arm64': '2', 'armhf': '2'}>
+CONFIG_SERIAL_SIFIVE                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_SPRD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIAL_ST_ASC                            policy<{'armhf': 'm'}>
+CONFIG_SERIAL_TEGRA                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SERIAL_TEGRA_TCU                         policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SERIAL_TEGRA_TCU_CONSOLE                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SERIAL_UARTLITE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SERIAL_UARTLITE_NR_UARTS                 policy<{'amd64': '1', 'arm64': '1', 'armhf': '1', 'ppc64el': '1', 's390x': '1'}>
+CONFIG_SERIAL_XILINX_PS_UART                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SERIO_ALTERA_PS2                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_AMBAKMI                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SERIO_APBPS2                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_ARC_PS2                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_CT82C710                           policy<{'amd64': 'm'}>
+CONFIG_SERIO_GPIO_PS2                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_I8042                              policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIO_LIBPS2                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SERIO_NVEC_PS2                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SERIO_PARKBD                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_PCIPS2                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_PS2MULT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_RAW                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_SERPORT                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SERIO_SUN4I_PS2                          policy<{'arm64': 'n'}>
+CONFIG_SERIO_XILINX_XPS_PS2                     policy<{'ppc64el': 'm'}>
+CONFIG_SFC                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SFC_FALCON                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SFC_FALCON_MTD                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SFC_MCDI_LOGGING                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SFC_MCDI_MON                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SFC_MTD                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SFC_SRIOV                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SFP                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SF_PDMA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SGETMASK_SYSCALL                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SGI_GRU                                  policy<{'amd64': 'm'}>
+CONFIG_SGI_GRU_DEBUG                            policy<{'amd64': 'n'}>
+CONFIG_SGI_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SGI_XP                                   policy<{'amd64': 'm'}>
+CONFIG_SGL_ALLOC                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SG_POOL                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SG_SPLIT                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SHIFT_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SHIFT_FS_POSIX_ACL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SHMEM                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SHUFFLE_PAGE_ALLOCATOR                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SH_ETH                                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SH_TIMER_CMT                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SH_TIMER_MTU2                            policy<{'armhf': 'y'}>
+CONFIG_SH_TIMER_TMU                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SI1133                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SI1145                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SI7005                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SI7020                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SIGNALFD                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SIGNATURE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SIGNED_PE_FILE_VERIFICATION              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SIOX                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SIOX_BUS_GPIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SIS190                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SIS900                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SKB_EXTENSIONS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SKFP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SKGE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SKGE_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SKGE_GENESIS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SKY2                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SKY2_DEBUG                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SL28CPLD_WATCHDOG                        policy<{'arm64': 'm'}>
+CONFIG_SLAB                                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SLAB_FREELIST_HARDENED                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SLAB_FREELIST_RANDOM                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SLAB_MERGE_DEFAULT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SLHC                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SLICOSS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SLIC_DS26522                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SLIMBUS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SLIM_QCOM_CTRL                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SLIM_QCOM_NGD_CTRL                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SLIP                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SLIP_COMPRESSED                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SLIP_MODE_SLIP6                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SLIP_SMART                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SLOB                                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SLS                                      policy<{'amd64': 'y'}>
+CONFIG_SLUB                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SLUB_CPU_PARTIAL                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SLUB_DEBUG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SLUB_DEBUG_ON                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SLUB_STATS                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SMARTJOYPLUS_FF                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SMBFS_COMMON                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SMB_SERVER                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SMB_SERVER_CHECK_CAP_NET_ADMIN           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SMB_SERVER_KERBEROS5                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SMB_SERVER_SMBDIRECT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SMC911X                                  policy<{'armhf': 'm'}>
+CONFIG_SMC91X                                   policy<{'arm64': 'y', 'armhf': 'm'}>
+CONFIG_SMP                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SMP_ON_UP                                policy<{'armhf': 'y'}>
+CONFIG_SMSC37B787_WDT                           policy<{'amd64': 'm'}>
+CONFIG_SMSC911X                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SMSC9420                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SMSC_PHY                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SMSC_SCH311X_WDT                         policy<{'amd64': 'm'}>
+CONFIG_SMSGIUCV                                 policy<{'s390x': 'y'}>
+CONFIG_SMSGIUCV_EVENT                           policy<{'s390x': 'm'}>
+CONFIG_SMS_SDIO_DRV                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SMS_SIANO_DEBUGFS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SMS_SIANO_MDTV                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SMS_SIANO_RC                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SMS_USB_DRV                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SM_CAMCC_8250                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_DISPCC_8250                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_FTL                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SM_GCC_6115                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GCC_6125                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GCC_6350                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GCC_8150                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GCC_8250                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GCC_8350                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GPUCC_8150                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_GPUCC_8250                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_VIDEOCC_8150                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SM_VIDEOCC_8250                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_AC97_CODEC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AC97_POWER_SAVE                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_AC97_POWER_SAVE_DEFAULT              policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_SND_AD1889                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ALI5451                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_ALOOP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ALS300                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_ALS4000                              policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ARM                                  policy<{'armhf': 'y'}>
+CONFIG_SND_ARMAACI                              policy<{'armhf': 'm'}>
+CONFIG_SND_ASIHPI                               policy<{'amd64': 'm'}>
+CONFIG_SND_ATIIXP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ATIIXP_MODEM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ATMEL_SOC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AU8810                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AU8820                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AU8830                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AUDIO_GRAPH_CARD                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AW2                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_AZT3328                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_BCD2000                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_BCM2835                              policy<{'arm64': 'm'}>
+CONFIG_SND_BCM2835_SOC_I2S                      policy<{'arm64': 'm'}>
+CONFIG_SND_BCM63XX_I2S_WHISTLER                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_BEBOB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_BT87X                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_BT87X_OVERCLOCK                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_CA0106                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_CMIPCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_COMPRESS_OFFLOAD                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND_CS4281                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_CS46XX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_CS46XX_NEW_DSP                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_CTL_LED                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_CTXFI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_DARLA20                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_DARLA24                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_DESIGNWARE_I2S                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_DESIGNWARE_PCM                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_DICE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_DMAENGINE_PCM                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND_DMA_SGBUF                            policy<{'amd64': 'y'}>
+CONFIG_SND_DRIVERS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_DUMMY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_DYNAMIC_MINORS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_ECHO3G                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_EMU10K1                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_EMU10K1X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_EMU10K1_SEQ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_ENS1370                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ENS1371                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ES1938                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_ES1968                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_ES1968_INPUT                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y'}>
+CONFIG_SND_ES1968_RADIO                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y'}>
+CONFIG_SND_FIREFACE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FIREWIRE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_FIREWIRE_DIGI00X                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FIREWIRE_LIB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FIREWIRE_MOTU                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FIREWIRE_TASCAM                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FIREWORKS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FM801                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_FM801_TEA575X_BOOL                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_GINA20                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_GINA24                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_ALIGNED_MMIO                     policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SND_HDA_CODEC_ANALOG                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_CA0110                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_CA0132                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_CA0132_DSP                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_CODEC_CIRRUS                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_CMEDIA                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_CONEXANT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_CS8409                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_HDMI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_REALTEK                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_SI3054                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_SIGMATEL                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_CODEC_VIA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_COMPONENT                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_DSP_LOADER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_EXT_CORE                         policy<{'amd64': 'm'}>
+CONFIG_SND_HDA_GENERIC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_GENERIC_LEDS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_HWDEP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_I915                             policy<{'amd64': 'y'}>
+CONFIG_SND_HDA_INPUT_BEEP                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_INPUT_BEEP_MODE                  policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_SND_HDA_INTEL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDA_INTEL_HDMI_SILENT_STREAM         policy<{'amd64': 'y', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_HDA_PATCH_LOADER                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_HDA_PREALLOC_SIZE                    policy<{'amd64': '0', 'arm64': '64', 'armhf': '64', 'ppc64el': '64'}>
+CONFIG_SND_HDA_TEGRA                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_HDSP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HDSPM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HRTIMER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_HWDEP                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_I2S_HI6210_I2S                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_ICE1712                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_ICE1724                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_IMX_SOC                              policy<{'arm64': 'm', 'armhf-generic': 'y'}>
+CONFIG_SND_INDIGO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INDIGODJ                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INDIGODJX                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INDIGOIO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INDIGOIOX                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INTEL8X0                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INTEL8X0M                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INTEL_BYT_PREFER_SOF                 policy<{'amd64': 'y'}>
+CONFIG_SND_INTEL_DSP_CONFIG                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_INTEL_NHLT                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SND_INTEL_SOUNDWIRE_ACPI                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_ISIGHT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_JACK                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_JACK_INPUT_DEV                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_KIRKWOOD_SOC                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_KIRKWOOD_SOC_ARMADA370_DB            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_KORG1212                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_LAYLA20                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_LAYLA24                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_LOLA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_LX6464ES                             policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MAESTRO3                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_MAESTRO3_INPUT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y'}>
+CONFIG_SND_MAX_CARDS                            policy<{'amd64': '32', 'arm64': '32', 'armhf': '32', 'ppc64el': '32'}>
+CONFIG_SND_MESON_AIU                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_FIFO                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_FRDDR                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_PDM                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_SOUND_CARD                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_SPDIFIN                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_SPDIFOUT                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_TDMIN                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_TDMOUT                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_TDM_FORMATTER              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_TDM_INTERFACE              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_AXG_TODDR                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_CARD_UTILS                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_CODEC_GLUE                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_G12A_TOACODEC                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_G12A_TOHDMITX                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MESON_GX_SOUND_CARD                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_MIA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MIXART                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MIXER_OSS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MONA                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MPU401                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MPU401_UART                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MTPAV                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_MTS64                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_NM256                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_OPL3_LIB                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_OPL3_LIB_SEQ                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_OSSEMUL                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_OXFW                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_OXYGEN                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_OXYGEN_LIB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_PCI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_PCM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND_PCMCIA                               policy<{'amd64': 'y'}>
+CONFIG_SND_PCM_ELD                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_PCM_IEC958                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_PCM_TIMER                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_PCSP                                 policy<{'amd64': 'm'}>
+CONFIG_SND_PCXHR                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_PDAUDIOCF                            policy<{'amd64': 'm'}>
+CONFIG_SND_PORTMAN2X4                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_PPC                                  policy<{'ppc64el': 'y'}>
+CONFIG_SND_PROC_FS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_RAWMIDI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_RIPTIDE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_RME32                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_RME96                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_RME9652                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SAMSUNG_I2S                          policy<{'armhf': 'm'}>
+CONFIG_SND_SAMSUNG_PCM                          policy<{'armhf': 'm'}>
+CONFIG_SND_SAMSUNG_SPDIF                        policy<{'armhf': 'm'}>
+CONFIG_SND_SB_COMMON                            policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQUENCER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQUENCER_OSS                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_SEQ_DEVICE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQ_DUMMY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQ_HRTIMER_DEFAULT                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SEQ_MIDI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQ_MIDI_EMUL                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQ_MIDI_EVENT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SEQ_VIRMIDI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SERIAL_U16550                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SIMPLE_CARD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SIMPLE_CARD_UTILS                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AC97_BUS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SOC_AC97_CODEC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ACPI                             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_ACPI_INTEL_MATCH                 policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_ADAU1372                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU1372_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU1372_SPI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU1701                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU1761                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU1761_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU1761_SPI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU17X1                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU7002                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU7118                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU7118_HW                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU7118_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADAU_UTILS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADI_AXI_I2S                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ADI_AXI_SPDIF                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK4104                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK4118                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK4458                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK4554                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK4613                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK4642                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK5386                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AK5558                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ALC5623                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ALC5632                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_AMD_ACP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AMD_ACP3x                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_AMD_ACP5x                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_AMD_CZ_DA7219MX98357_MACH        policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_SOC_AMD_CZ_RT5645_MACH               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_AMD_RV_RT5682_MACH               policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_APQ8016_SBC                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ARIZONA                          policy<{'amd64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ARNDALE                          policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_BD28623                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_BT_SCO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_COMPRESS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SOC_CPCAP                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CROS_EC_CODEC                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_CS35L32                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L33                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L34                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L35                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS35L36                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4234                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4265                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4270                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4271                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4271_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4271_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42L42                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42L51                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42L51_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42L52                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42L56                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42L73                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42XX8                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS42XX8_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS43130                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4341                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS4349                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CS53L30                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_CX2072X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_DA7213                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_DA7219                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_DAVINCI_MCASP                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_DMIC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ES7134                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ES7241                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ES8316                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ES8328                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ES8328_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ES8328_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_EUKREA_TLV320                    policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_FSL_ASOC_CARD                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_FSL_ASRC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_AUD2HTX                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_FSL_AUDMIX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_EASRC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_ESAI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_MICFIL                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_MQS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_RPMSG                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_SAI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_SPDIF                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_SSI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'y', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_FSL_XCVR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_GENERIC_DMAENGINE_PCM            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SOC_GTM601                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_HDAC_HDA                         policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_HDAC_HDMI                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_HDMI_CODEC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_I2C_AND_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ICS43432                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMG                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SOC_IMG_I2S_IN                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMG_I2S_OUT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMG_PARALLEL_OUT                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMG_PISTACHIO_INTERNAL_DAC       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMG_SPDIF_IN                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMG_SPDIF_OUT                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMX_AUDIO_RPMSG                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_AUDMIX                       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_AUDMUX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'y', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_IMX_CARD                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_ES8328                       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_HDMI                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_PCM_DMA                      policy<{'arm64': 'm', 'armhf-generic': 'y'}>
+CONFIG_SND_SOC_IMX_PCM_FIQ                      policy<{'armhf-generic': 'y'}>
+CONFIG_SND_SOC_IMX_PCM_RPMSG                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_RPMSG                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_IMX_SGTL5000                     policy<{'arm64': 'm', 'armhf-generic': 'y'}>
+CONFIG_SND_SOC_IMX_SPDIF                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_INNO_RK3036                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_INTEL_APL                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BDW_RT5650_MACH            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BDW_RT5677_MACH            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BROADWELL_MACH             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BXT_DA7219_MAX98357A_COMMON policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BXT_DA7219_MAX98357A_MACH  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BXT_RT298_MACH             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYTCR_RT5640_MACH          policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYTCR_RT5651_MACH          policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYTCR_WM5102_MACH          policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYT_CHT_CX2072X_MACH       policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYT_CHT_DA7213_MACH        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYT_CHT_ES8316_MACH        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_BYT_CHT_NOCODEC_MACH       policy<{'amd64': 'n'}>
+CONFIG_SND_SOC_INTEL_CATPT                      policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_CHT_BSW_MAX98090_TI_MACH   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_CHT_BSW_NAU8824_MACH       policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_CHT_BSW_RT5645_MACH        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_CHT_BSW_RT5672_MACH        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_CML_LP_DA7219_MAX98357A_MACH policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_DA7219_MAX98357A_GENERIC   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_EHL_RT5660_MACH            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_GLK                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_GLK_DA7219_MAX98357A_MACH  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_GLK_RT5682_MAX98357A_MACH  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_HASWELL_MACH               policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_HDA_DSP_COMMON             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KBL                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KBL_DA7219_MAX98357A_MACH  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KBL_DA7219_MAX98927_MACH   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KBL_RT5660_MACH            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KBL_RT5663_MAX98927_MACH   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KBL_RT5663_RT5514_MAX98927_MACH policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_KEEMBAY                    policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_INTEL_MACH                       policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_INTEL_SKL                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKL_HDA_DSP_GENERIC_MACH   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKL_NAU88L25_MAX98357A_MACH policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKL_NAU88L25_SSM4567_MACH  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKL_RT286_MACH             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKYLAKE_COMMON             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKYLAKE_FAMILY             policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SKYLAKE_SSP_CLK            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_CML_RT1011_RT5682_MACH policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_CS42L42_MACH           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_DA7219_MAX98373_MACH   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_MAXIM_COMMON           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_PCM512x_MACH           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_RT5682_MACH            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SOF_WM8804_MACH            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SST                        policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_INTEL_SST_TOPLEVEL               policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_J721E_EVM                        policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_LOCHNAGAR_SC                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_LPASS_APQ8016                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_LPASS_CPU                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_LPASS_HDMI                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_LPASS_IPQ806X                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_LPASS_PLATFORM                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_LPASS_RX_MACRO                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_LPASS_SC7180                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_LPASS_TX_MACRO                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_LPASS_VA_MACRO                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_LPASS_WSA_MACRO                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX9759                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98088                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98090                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MAX98095                         policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_MAX98357A                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98373                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98373_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98373_SDW                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98390                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98504                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX9860                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX9867                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MAX98927                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MEDIATEK                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MESON_T9015                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MIKROE_PROTO                     policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MSM8916_WCD_ANALOG               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MSM8916_WCD_DIGITAL              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MSM8996                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT2701                           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_SND_SOC_MT6351                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MT6358                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MT6359                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT6359_ACCDET                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT6660                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_MT6797                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT6797_MT6351                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8173                           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_SND_SOC_MT8183                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8183_DA7219_MAX98357A          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8183_MT6358_TS3A227E_MAX98357A policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8192                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8192_MT6359_RT1015_RT5682      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8195                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MT8195_MT6359_RT1019_RT5682      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_MTK_BTCVSD                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_NAU8315                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_NAU8540                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_NAU8810                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_NAU8822                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_NAU8824                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_NAU8825                          policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_NOKIA_RX51                       policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_ODROID                           policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_OMAP3_PANDORA                    policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_OMAP3_TWL4030                    policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_OMAP_ABE_TWL6040                 policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_OMAP_DMIC                        policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_OMAP_MCBSP                       policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_OMAP_MCPDM                       policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_PCM1681                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM1789                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM1789_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM179X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM179X_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM179X_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM186X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM186X_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM186X_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM3060                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM3060_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM3060_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM3168A                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM3168A_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM3168A_SPI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM5102A                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM512x                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM512x_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_PCM512x_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_QCOM                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QCOM_COMMON                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_ADM                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_AFE                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_AFE_CLOCKS                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_AFE_DAI                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_ASM                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_ASM_DAI                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_COMMON                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_CORE                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_QDSP6_ROUTING                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RCAR                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RK3288_HDMI_ANALOG               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RK3328                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RK3399_GRU_SOUND                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RK817                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RL6231                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RL6347A                          policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_ROCKCHIP                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ROCKCHIP_I2S                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ROCKCHIP_MAX98090                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ROCKCHIP_PDM                     policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ROCKCHIP_RT5645                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_ROCKCHIP_SPDIF                   policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT1011                           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT1015                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT1015P                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT1308                           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT1308_SDW                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT1316_SDW                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT286                            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT298                            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT5514                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT5514_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT5616                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT5631                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT5640                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT5645                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT5651                           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT5659                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT5660                           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT5663                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT5670                           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_RT5677                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_RT5677_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_RT5682                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT5682_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_RT5682_SDW                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT700                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT700_SDW                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT711                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT711_SDCA_SDW                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT711_SDW                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT715                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT715_SDCA_SDW                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RT715_SDW                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_RZ                               policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SAMSUNG                          policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SAMSUNG_ARIES_WM8994             policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SAMSUNG_MIDAS_WM1811             policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SAMSUNG_SMDK_SPDIF               policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SAMSUNG_SMDK_WM8994              policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SAMSUNG_TM2_WM5110               policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SC7180                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_SDM845                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_SDW_MOCKUP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SGTL5000                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic': 'y', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SH4_FSI                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_SI476X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SIGMADSP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SIGMADSP_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SIGMADSP_REGMAP                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SIMPLE_AMPLIFIER                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SIMPLE_MUX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SM8250                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_SMDK_WM8994_PCM                  policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SNOW                             policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_SOF                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SOF_ACPI                         policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_SOC_SOF_ACPI_DEV                     policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_ALDERLAKE                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_APOLLOLAKE                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_BAYTRAIL                     policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_BROADWELL                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_CANNONLAKE                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_COFFEELAKE                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_COMETLAKE                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_DEBUG_PROBES                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_SOC_SOF_DEVELOPER_SUPPORT            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_SOC_SOF_ELKHARTLAKE                  policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_GEMINILAKE                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_HDA                          policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_HDA_COMMON                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_HDA_LINK_BASELINE            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_ICELAKE                      policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_IMX8                         policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SOF_IMX8M                        policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SOF_IMX8M_SUPPORT                policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_SOF_IMX8_SUPPORT                 policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_SOF_IMX_COMMON                   policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SOF_IMX_OF                       policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SOF_IMX_TOPLEVEL                 policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_SOF_INTEL_APL                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_ATOM_HIFI_EP           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_CNL                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_COMMON                 policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_HIFI_EP_IPC            policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_ICL                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_SOUNDWIRE              policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_TGL                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_INTEL_TOPLEVEL               policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_SOF_JASPERLAKE                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_MERRIFIELD                   policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_OF                           policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SOF_PCI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SOF_PCI_DEV                      policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_PROBE_WORK_QUEUE             policy<{'amd64': 'y'}>
+CONFIG_SND_SOC_SOF_TIGERLAKE                    policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_SOF_TOPLEVEL                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SOC_SOF_XTENSA                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_SOC_SPDIF                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SPRD                             policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SPRD_MCDT                        policy<{'arm64': 'm'}>
+CONFIG_SND_SOC_SSM2305                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SSM2518                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SSM2602                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SSM2602_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SSM2602_SPI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_SSM4567                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_STA32X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_STA350                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_STI_SAS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_STORM                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_TAS2552                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS2562                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS2764                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS2770                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS5086                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS571X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS5720                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TAS6424                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TDA7419                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TEGRA                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA186_DSPK                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA20_AC97                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA20_DAS                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA20_I2S                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA20_SPDIF                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA210_ADMAIF                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA210_AHUB                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA210_DMIC                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA210_I2S                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA30_AHUB                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA30_I2S                      policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_ALC5632                    policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_AUDIO_GRAPH_CARD           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_MACHINE_DRV                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_MAX98090                   policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_RT5640                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_RT5677                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_SGTL5000                   policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_TRIMSLICE                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_WM8753                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_WM8903                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TEGRA_WM9712                     policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TFA9879                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TFA989X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TI_EDMA_PCM                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_TI_SDMA_PCM                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_TI_UDMA_PCM                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_TLV320ADCX140                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC23                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC23_I2C                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC23_SPI                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC31XX                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC32X4                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC32X4_I2C                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC32X4_SPI                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC3X                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC3X_I2C                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TLV320AIC3X_SPI                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TOPOLOGY                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SOC_TPA6130A2                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TS3A227E                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TSCS42XX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TSCS454                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_TWL4030                          policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_TWL6040                          policy<{'armhf-generic': 'm'}>
+CONFIG_SND_SOC_UDA1334                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_UNIPHIER                         policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_UNIPHIER_AIO                     policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_UNIPHIER_EVEA_CODEC              policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_UNIPHIER_LD11                    policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_UNIPHIER_PXS2                    policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_WCD9335                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WCD934X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WCD938X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WCD938X_SDW                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WCD_MBHC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM5102                           policy<{'amd64': 'm'}>
+CONFIG_SND_SOC_WM5110                           policy<{'armhf': 'm'}>
+CONFIG_SND_SOC_WM8510                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8523                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8524                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8580                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8711                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8728                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8731                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8737                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8741                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8750                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8753                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8770                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8776                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8782                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8804                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8804_I2C                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8804_SPI                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8903                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8904                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8960                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8962                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8974                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8978                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8985                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM8994                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_WM9712                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SND_SOC_WM_ADSP                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_WM_HUBS                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SND_SOC_WSA881X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_XILINX_AUDIO_FORMATTER           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_XILINX_I2S                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_XILINX_SPDIF                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_XTFPGA_I2S                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SOC_ZL38060                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_SONICVIBES                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_SPI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SST_ATOM_HIFI2_PLATFORM              policy<{'amd64': 'm'}>
+CONFIG_SND_SST_ATOM_HIFI2_PLATFORM_ACPI         policy<{'amd64': 'm'}>
+CONFIG_SND_SST_ATOM_HIFI2_PLATFORM_PCI          policy<{'amd64': 'm'}>
+CONFIG_SND_SUN4I_CODEC                          policy<{'arm64': 'n'}>
+CONFIG_SND_SUN4I_I2S                            policy<{'arm64': 'n'}>
+CONFIG_SND_SUN4I_SPDIF                          policy<{'arm64': 'n'}>
+CONFIG_SND_SUN50I_CODEC_ANALOG                  policy<{'arm64': 'm'}>
+CONFIG_SND_SUN8I_ADDA_PR_REGMAP                 policy<{'arm64': 'm'}>
+CONFIG_SND_SUN8I_CODEC                          policy<{'arm64': 'm'}>
+CONFIG_SND_SUN8I_CODEC_ANALOG                   policy<{'arm64': 'm'}>
+CONFIG_SND_SUPPORT_OLD_API                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_SYNTH_EMUX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_TIMER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_SND_TRIDENT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm'}>
+CONFIG_SND_USB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_USB_6FIRE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_AUDIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_AUDIO_USE_MEDIA_CONTROLLER       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_USB_CAIAQ                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_CAIAQ_INPUT                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_USB_HIFACE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_LINE6                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_POD                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_PODHD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_TONEPORT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_UA101                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_US122L                           policy<{'amd64': 'm'}>
+CONFIG_SND_USB_USX2Y                            policy<{'amd64': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_USB_VARIAX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VERBOSE_PRINTK                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SND_VERBOSE_PROCFS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_VIA82XX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VIA82XX_MODEM                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VIRMIDI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VIRTIO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VIRTUOSO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VMASTER                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SND_VX222                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_VXPOCKET                             policy<{'amd64': 'm'}>
+CONFIG_SND_VX_LIB                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SND_X86                                  policy<{'amd64': 'y'}>
+CONFIG_SND_XEN_FRONTEND                         policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SND_YMFPCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SNI_AVE                                  policy<{'armhf': 'm'}>
+CONFIG_SNI_NETSEC                               policy<{'arm64': 'm'}>
+CONFIG_SOCFPGA_FPGA_BRIDGE                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SOCFPGA_SUSPEND                          policy<{'armhf': 'y'}>
+CONFIG_SOCIONEXT_SYNQUACER_PREITS               policy<{'arm64': 'y'}>
+CONFIG_SOCK_CGROUP_DATA                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SOCK_RX_QUEUE_MAPPING                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SOCK_VALIDATE_XMIT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SOC_AM33XX                               policy<{'armhf-generic': 'y', 'armhf-generic-lpae': 'n'}>
+CONFIG_SOC_AM43XX                               policy<{'armhf': 'n'}>
+CONFIG_SOC_BRCMSTB                              policy<{'arm64': 'y', 'armhf': 'n'}>
+CONFIG_SOC_BUS                                  policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SOC_DRA7XX                               policy<{'armhf': 'y'}>
+CONFIG_SOC_EXYNOS5250                           policy<{'armhf': 'y'}>
+CONFIG_SOC_EXYNOS5260                           policy<{'armhf': 'y'}>
+CONFIG_SOC_EXYNOS5410                           policy<{'armhf': 'y'}>
+CONFIG_SOC_EXYNOS5420                           policy<{'armhf': 'y'}>
+CONFIG_SOC_EXYNOS5800                           policy<{'armhf': 'y'}>
+CONFIG_SOC_HAS_OMAP2_SDRC                       policy<{'armhf': 'y'}>
+CONFIG_SOC_HAS_REALTIME_COUNTER                 policy<{'armhf': 'y'}>
+CONFIG_SOC_IMX5                                 policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX50                                policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX51                                policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX53                                policy<{'armhf-generic': 'n'}>
+CONFIG_SOC_IMX6                                 policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX6Q                                policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX6SL                               policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX6SLL                              policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX6SX                               policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX6UL                               policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX7D                                policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX7D_CA7                            policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX7ULP                              policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_IMX8M                                policy<{'arm64': 'y', 'armhf-generic': 'n'}>
+CONFIG_SOC_LS1021A                              policy<{'armhf-generic': 'n'}>
+CONFIG_SOC_OMAP3430                             policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_OMAP5                                policy<{'armhf': 'n'}>
+CONFIG_SOC_RENESAS                              policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SOC_SAMSUNG                              policy<{'armhf': 'y'}>
+CONFIG_SOC_TEGRA20_VOLTAGE_COUPLER              policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_TEGRA30_VOLTAGE_COUPLER              policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_TEGRA_FLOWCTRL                       policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SOC_TEGRA_FUSE                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SOC_TEGRA_PMC                            policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SOC_TEGRA_POWERGATE_BPMP                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_SOC_TI                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SOC_TI81XX                               policy<{'armhf-generic': 'y'}>
+CONFIG_SOC_VF610                                policy<{'armhf-generic': 'y'}>
+CONFIG_SOFTLOCKUP_DETECTOR                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SOFT_WATCHDOG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SOFT_WATCHDOG_PRETIMEOUT                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SOLARIS_X86_PARTITION                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SONYPI_COMPAT                            policy<{'amd64': 'y'}>
+CONFIG_SONY_FF                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SONY_LAPTOP                              policy<{'amd64': 'm'}>
+CONFIG_SOUNDWIRE_CADENCE                        policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SOUNDWIRE_GENERIC_ALLOCATION             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SOUNDWIRE_INTEL                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SOUNDWIRE_QCOM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SOUND_OSS_CORE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SP5100_TCO                               policy<{'amd64': 'm'}>
+CONFIG_SPAPR_TCE_IOMMU                          policy<{'ppc64el': 'y'}>
+CONFIG_SPARSEMEM                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SPARSEMEM_EXTREME                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SPARSEMEM_MANUAL                         policy<{'amd64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPARSEMEM_STATIC                         policy<{'armhf': 'y'}>
+CONFIG_SPARSEMEM_VMEMMAP                        policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE                 policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SPARSE_IRQ                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SPARX5_SWITCH                            policy<{'amd64': '-', 'arm64': 'm', 'armhf': '-', 'ppc64el': '-'}>
+CONFIG_SPEAKUP_SYNTH_ACNTSA                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_APOLLO                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_AUDPTR                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_BNS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_DECEXT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_DECTLK                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_DUMMY                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_LTLK                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_SOFT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_SPKOUT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPEAKUP_SYNTH_TXPRT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': '-'}>
+CONFIG_SPI                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SPI_ALTERA                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_ALTERA_CORE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_ALTERA_DFL                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_AMD                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_ARMADA_3700                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_ASPEED_SMC                           policy<{'armhf': 'm'}>
+CONFIG_SPI_AXI_SPI_ENGINE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_BCM2835                              policy<{'arm64': 'm'}>
+CONFIG_SPI_BCM2835AUX                           policy<{'arm64': 'm'}>
+CONFIG_SPI_BCM_QSPI                             policy<{'arm64': 'm'}>
+CONFIG_SPI_BITBANG                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_BUTTERFLY                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_CADENCE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_CADENCE_QUADSPI                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SPI_DESIGNWARE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_DLN2                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_DW_DMA                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_DW_MMIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_DW_PCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_DYNAMIC                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_FSI                                  policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_FSL_DSPI                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_FSL_LIB                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_FSL_LPSPI                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_FSL_QUADSPI                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_FSL_SPI                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_GPIO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_HISI_KUNPENG                         policy<{'arm64': 'm'}>
+CONFIG_SPI_HISI_SFC                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_HISI_SFC_V3XX                        policy<{'arm64': 'm'}>
+CONFIG_SPI_IMX                                  policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_LANTIQ_SSC                           policy<{'amd64': 'm'}>
+CONFIG_SPI_LJCA                                 policy<{'amd64': 'm'}>
+CONFIG_SPI_LM70_LLP                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_LOOPBACK_TEST                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_MASTER                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_MEM                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_MESON_SPICC                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_MESON_SPIFC                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_MT65XX                               policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_MTK_NOR                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_MUX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_MXIC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_NPCM_FIU                             policy<{'armhf': 'm'}>
+CONFIG_SPI_NPCM_PSPI                            policy<{'armhf': 'm'}>
+CONFIG_SPI_NXP_FLEXSPI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_OC_TINY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_OMAP24XX                             policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SPI_ORION                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_PL022                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_PXA2XX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_PXA2XX_PCI                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_QCOM_GENI                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_QCOM_QSPI                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_QUP                                  policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_ROCKCHIP                             policy<{'amd64': 'n', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'n'}>
+CONFIG_SPI_ROCKCHIP_SFC                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_RPCIF                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_RSPI                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_S3C64XX                              policy<{'armhf': 'm'}>
+CONFIG_SPI_SC18IS602                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_SH_HSPI                              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_SH_MSIOF                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_SIFIVE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_SLAVE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SPI_SLAVE_MT27XX                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPI_SLAVE_SYSTEM_CONTROL                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_SLAVE_TIME                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_SPIDEV                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_SPRD                                 policy<{'arm64': 'm'}>
+CONFIG_SPI_SPRD_ADI                             policy<{'arm64': 'm'}>
+CONFIG_SPI_SUN4I                                policy<{'arm64': 'n'}>
+CONFIG_SPI_SUN6I                                policy<{'arm64': 'm'}>
+CONFIG_SPI_SYNQUACER                            policy<{'arm64': 'm'}>
+CONFIG_SPI_TEGRA114                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_TEGRA20_SFLASH                       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_TEGRA20_SLINK                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_TEGRA210_QUAD                        policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_SPI_THUNDERX                             policy<{'arm64': 'm'}>
+CONFIG_SPI_TI_QSPI                              policy<{'armhf': 'm'}>
+CONFIG_SPI_TLE62X0                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_UNIPHIER                             policy<{'armhf': 'm'}>
+CONFIG_SPI_XCOMM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPI_XILINX                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SPI_XLP                                  policy<{'arm64': 'm'}>
+CONFIG_SPI_ZYNQMP_GQSPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPLIT_PTLOCK_CPUS                        policy<{'amd64': '4', 'arm64': '4', 'armhf': '4', 'ppc64el': '4', 's390x': '4'}>
+CONFIG_SPMI                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SPMI_HISI3670                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPMI_MSM_PMIC_ARB                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPMI_PMIC_CLKDIV                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_SPRD_COMMON_CLK                          policy<{'arm64': 'm'}>
+CONFIG_SPRD_DMA                                 policy<{'arm64': 'm'}>
+CONFIG_SPRD_EFUSE                               policy<{'arm64': 'm'}>
+CONFIG_SPRD_IOMMU                               policy<{'arm64': 'm'}>
+CONFIG_SPRD_MBOX                                policy<{'arm64': 'm'}>
+CONFIG_SPRD_SC9860_CLK                          policy<{'arm64': 'm'}>
+CONFIG_SPRD_SC9863A_CLK                         policy<{'arm64': 'm'}>
+CONFIG_SPRD_THERMAL                             policy<{'arm64': 'm'}>
+CONFIG_SPRD_TIMER                               policy<{'arm64': 'y'}>
+CONFIG_SPRD_WATCHDOG                            policy<{'arm64': 'm'}>
+CONFIG_SPS30                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPS30_I2C                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SPS30_SERIAL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SQUASHFS_DECOMP_MULTI                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SQUASHFS_DECOMP_SINGLE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_EMBEDDED                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SQUASHFS_FILE_CACHE                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SQUASHFS_FILE_DIRECT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE             policy<{'amd64': '3', 'arm64': '3', 'armhf': '3', 'ppc64el': '3', 's390x': '3'}>
+CONFIG_SQUASHFS_LZ4                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_LZO                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_XATTR                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_XZ                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_ZLIB                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SQUASHFS_ZSTD                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SRAM                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SRAM_EXEC                                policy<{'armhf': 'y'}>
+CONFIG_SRCU                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SRF04                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SRF08                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SSB                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SSB_B43_PCI_BRIDGE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_BLOCKIO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_DRIVER_GPIO                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_DRIVER_PCICORE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_DRIVER_PCICORE_POSSIBLE              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_PCIHOST                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_PCIHOST_POSSIBLE                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_PCMCIAHOST                           policy<{'amd64': 'n'}>
+CONFIG_SSB_PCMCIAHOST_POSSIBLE                  policy<{'amd64': 'y'}>
+CONFIG_SSB_POSSIBLE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SSB_SDIOHOST                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_SDIOHOST_POSSIBLE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSB_SPROM                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SSFDC                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SSI_PROTOCOL                             policy<{'armhf-generic': 'm'}>
+CONFIG_STACKPROTECTOR                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_STACKPROTECTOR_PER_TASK                  policy<{'arm64': 'y'}>
+CONFIG_STACKPROTECTOR_STRONG                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_STACKTRACE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STACKTRACE_BUILD_ID                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_STACKTRACE_SUPPORT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STACK_TRACER                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STAGING                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_STAGING_BOARD                            policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_STAGING_MEDIA                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_STANDALONE                               policy<{'amd64': 'n', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STATIC_CALL_SELFTEST                     policy<{'amd64': 'n'}>
+CONFIG_STATIC_KEYS_SELFTEST                     policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_STATIC_USERMODEHELPER                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_STE10XP                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STK3310                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STK8312                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STK8BA50                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STM                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STMMAC_ETH                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STMMAC_PCI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STMMAC_PLATFORM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STMMAC_SELFTESTS                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_STMPE_ADC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STMPE_I2C                                policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_STMPE_SPI                                policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_STMP_DEVICE                              policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_STM_DUMMY                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STM_PROTO_BASIC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STM_PROTO_SYS_T                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STM_SOURCE_CONSOLE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STM_SOURCE_FTRACE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STM_SOURCE_HEARTBEAT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STP                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_STPMIC1_WATCHDOG                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_STREAM_PARSER                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STRICT_DEVMEM                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STRICT_KERNEL_RWX                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STRICT_MODULE_RWX                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_STRICT_SIGALTSTACK_SIZE                  policy<{'amd64': 'n'}>
+CONFIG_STRING_SELFTEST                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_STRIP_ASM_SYMS                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_STUB_CLK_HI3660                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_STUB_CLK_HI6220                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_STX104                                   policy<{'amd64': 'm'}>
+CONFIG_ST_UVIS25                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ST_UVIS25_I2C                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ST_UVIS25_SPI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SUN4I_EMAC                               policy<{'arm64': 'n'}>
+CONFIG_SUN4I_GPADC                              policy<{'arm64': 'n'}>
+CONFIG_SUN4I_TIMER                              policy<{'arm64': 'y'}>
+CONFIG_SUN50I_A100_CCU                          policy<{'arm64': 'y'}>
+CONFIG_SUN50I_A100_R_CCU                        policy<{'arm64': 'y'}>
+CONFIG_SUN50I_A64_CCU                           policy<{'arm64': 'y'}>
+CONFIG_SUN50I_DE2_BUS                           policy<{'arm64': 'y'}>
+CONFIG_SUN50I_ERRATUM_UNKNOWN1                  policy<{'arm64': 'y'}>
+CONFIG_SUN50I_H616_CCU                          policy<{'arm64': 'y'}>
+CONFIG_SUN50I_H6_CCU                            policy<{'arm64': 'y'}>
+CONFIG_SUN50I_H6_R_CCU                          policy<{'arm64': 'y'}>
+CONFIG_SUN50I_IOMMU                             policy<{'arm64': 'y'}>
+CONFIG_SUN6I_MSGBOX                             policy<{'arm64': 'y'}>
+CONFIG_SUN8I_A83T_CCU                           policy<{'arm64': 'y'}>
+CONFIG_SUN8I_DE2_CCU                            policy<{'arm64': 'y'}>
+CONFIG_SUN8I_H3_CCU                             policy<{'arm64': 'y'}>
+CONFIG_SUN8I_R_CCU                              policy<{'arm64': 'y'}>
+CONFIG_SUN8I_THERMAL                            policy<{'arm64': 'm'}>
+CONFIG_SUNDANCE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SUNDANCE_MMIO                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SUNGEM                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SUNGEM_PHY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SUNRPC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SUNRPC_BACKCHANNEL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SUNRPC_DEBUG                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SUNRPC_DISABLE_INSECURE_ENCTYPES         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SUNRPC_GSS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SUNRPC_SWAP                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SUNRPC_XPRT_RDMA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_SUNXI_CCU                                policy<{'arm64': 'y'}>
+CONFIG_SUNXI_MBUS                               policy<{'arm64': 'y'}>
+CONFIG_SUNXI_RSB                                policy<{'arm64': 'm'}>
+CONFIG_SUNXI_SRAM                               policy<{'arm64': 'y'}>
+CONFIG_SUNXI_WATCHDOG                           policy<{'arm64': 'm'}>
+CONFIG_SUN_PARTITION                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SURFACE3_WMI                             policy<{'amd64': 'm'}>
+CONFIG_SURFACE_3_BUTTON                         policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_SURFACE_3_POWER_OPREGION                 policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_SURFACE_ACPI_NOTIFY                      policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_AGGREGATOR                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_AGGREGATOR_BUS                   policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SURFACE_AGGREGATOR_CDEV                  policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_AGGREGATOR_ERROR_INJECTION       policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_SURFACE_AGGREGATOR_REGISTRY              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_DTX                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_GPE                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_HID                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_HID_CORE                         policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_HOTPLUG                          policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_KBD                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_PLATFORMS                        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SURFACE_PLATFORM_PROFILE                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_SURFACE_PRO3_BUTTON                      policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_SUSPEND                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SUSPEND_FREEZER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_SUSPEND_SKIP_SYNC                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_SVC_I3C_MASTER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SWAP                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SWIOTLB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SWIOTLB_XEN                              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_SWPHY                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SWP_EMULATE                              policy<{'armhf': 'y'}>
+CONFIG_SW_SYNC                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SX9310                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SX9500                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SXGBE_ETH                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SYMBOLIC_ERRNAME                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYNCLINK_CS                              policy<{'amd64': 'm'}>
+CONFIG_SYNCLINK_GT                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SYNC_FILE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYNTH_EVENTS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYNTH_EVENT_GEN_TEST                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_SYN_COOKIES                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSCON_REBOOT_MODE                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SYSCTL                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSCTL_EXCEPTION_TRACE                   policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSC_R8A7742                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7743                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7745                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A77470                            policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A774A1                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A774B1                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A774C0                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A774E1                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A7779                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7790                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7791                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7792                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7794                             policy<{'armhf': 'y'}>
+CONFIG_SYSC_R8A7795                             policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77960                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77961                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77965                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77970                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77980                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77990                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A77995                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_R8A779A0                            policy<{'arm64': 'y'}>
+CONFIG_SYSC_RCAR                                policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SYSC_RMOBILE                             policy<{'armhf': 'y'}>
+CONFIG_SYSFB                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SYSFB_SIMPLEFB                           policy<{'amd64': 'n', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SYSFS                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSFS_SYSCALL                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSTEM76_ACPI                            policy<{'amd64': 'm'}>
+CONFIG_SYSTEMPORT                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_SYSTEM_BLACKLIST_HASH_LIST               policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_SYSTEM_BLACKLIST_KEYRING                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSTEM_DATA_VERIFICATION                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSTEM_EXTRA_CERTIFICATE                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSTEM_EXTRA_CERTIFICATE_SIZE            policy<{'amd64': '4096', 'arm64': '4096', 'armhf': '4096', 'ppc64el': '4096', 's390x': '4096'}>
+CONFIG_SYSTEM_REVOCATION_KEYS                   policy<{'amd64': '"debian/canonical-revoked-certs.pem"', 'arm64': '"debian/canonical-revoked-certs.pem"', 'armhf': '"debian/canonical-revoked-certs.pem"', 'ppc64el': '"debian/canonical-revoked-certs.pem"', 's390x': '"debian/canonical-revoked-certs.pem"'}>
+CONFIG_SYSTEM_REVOCATION_LIST                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSTEM_TRUSTED_KEYRING                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSTEM_TRUSTED_KEYS                      policy<{'amd64': '"debian/canonical-certs.pem"', 'arm64': '"debian/canonical-certs.pem"', 'armhf': '"debian/canonical-certs.pem"', 'ppc64el': '"debian/canonical-certs.pem"', 's390x': '"debian/canonical-certs.pem"'}>
+CONFIG_SYSV68_PARTITION                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_SYSVIPC                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSVIPC_COMPAT                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSVIPC_SYSCTL                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_SYSV_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_SYS_HYPERVISOR                           policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_SYS_SUPPORTS_APM_EMULATION               policy<{'armhf': 'y'}>
+CONFIG_SYS_SUPPORTS_EM_STI                      policy<{'armhf': 'y'}>
+CONFIG_SYS_SUPPORTS_SH_CMT                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_SYS_SUPPORTS_SH_MTU2                     policy<{'armhf': 'y'}>
+CONFIG_SYS_SUPPORTS_SH_TMU                      policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_T5403                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TABLET_SERIAL_WACOM4                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TABLET_USB_ACECAD                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TABLET_USB_AIPTEK                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TABLET_USB_HANWANG                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TABLET_USB_KBTAB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TABLET_USB_PEGASUS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TAHVO_USB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TAHVO_USB_HOST_BY_DEFAULT                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TAP                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TARGET_CORE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TASKSTATS                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TASKS_RCU                                policy<{'amd64-lowlatency': 'y', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y'}>
+CONFIG_TASKS_RCU_GENERIC                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TASKS_RUDE_RCU                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TASKS_TRACE_RCU                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TASK_DELAY_ACCT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TASK_IO_ACCOUNTING                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TASK_XACCT                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TCG_ATMEL                                policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_TCG_CRB                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_TCG_FTPM_TEE                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_TCG_IBMVTPM                              policy<{'ppc64el': 'y'}>
+CONFIG_TCG_INFINEON                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_TCG_NSC                                  policy<{'amd64': 'm'}>
+CONFIG_TCG_TIS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TCG_TIS_CORE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TCG_TIS_I2C_CR50                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TCG_TIS_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TCG_TIS_SPI_CR50                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TCG_TIS_ST33ZP24                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TCG_TIS_ST33ZP24_I2C                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TCG_TIS_ST33ZP24_SPI                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TCG_TIS_SYNQUACER                        policy<{'arm64': 'm'}>
+CONFIG_TCG_VTPM_PROXY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCG_XEN                                  policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_TCM_FC                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCM_FILEIO                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCM_IBLOCK                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCM_PSCSI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCM_QLA2XXX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TCM_QLA2XXX_DEBUG                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_TCM_USER2                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_ADVANCED                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TCP_CONG_BBR                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_BIC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_CDG                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_CUBIC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TCP_CONG_DCTCP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_HSTCP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_HTCP                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_HYBLA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_ILLINOIS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_LP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_NV                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_SCALABLE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_VEGAS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_VENO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_WESTWOOD                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_CONG_YEAH                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TCP_MD5SIG                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TCS3414                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TCS3472                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TEE                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm'}>
+CONFIG_TEE_BNXT_FW                              policy<{'arm64': 'm'}>
+CONFIG_TEGRA124_CLK_EMC                         policy<{'armhf-generic': 'y'}>
+CONFIG_TEGRA124_EMC                             policy<{'armhf-generic': 'y'}>
+CONFIG_TEGRA20_APB_DMA                          policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA20_EMC                              policy<{'armhf-generic': 'y'}>
+CONFIG_TEGRA210_ADMA                            policy<{'arm64': 'm', 'armhf-generic': 'n'}>
+CONFIG_TEGRA210_EMC                             policy<{'arm64': 'm'}>
+CONFIG_TEGRA210_EMC_TABLE                       policy<{'arm64': 'y'}>
+CONFIG_TEGRA30_EMC                              policy<{'armhf-generic': 'y'}>
+CONFIG_TEGRA30_TSENSOR                          policy<{'armhf-generic': 'm'}>
+CONFIG_TEGRA_ACONNECT                           policy<{'arm64': 'm', 'armhf-generic': 'n'}>
+CONFIG_TEGRA_AHB                                policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_BPMP                               policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_BPMP_THERMAL                       policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_TEGRA_CLK_DFLL                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_GMI                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_TEGRA_HOST1X                             policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_TEGRA_HOST1X_FIREWALL                    policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_HSP_MBOX                           policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_IOMMU_GART                         policy<{'armhf-generic': 'y'}>
+CONFIG_TEGRA_IOMMU_SMMU                         policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_IVC                                policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_MC                                 policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_SOCTHERM                           policy<{'arm64': 'n', 'armhf-generic': 'n'}>
+CONFIG_TEGRA_TIMER                              policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_TEGRA_VDE                                policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_TEGRA_WATCHDOG                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_TEHUTI                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TELCLOCK                                 policy<{'amd64': 'm'}>
+CONFIG_TERANETICS_PHY                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TEST_ASYNC_DRIVER_PROBE                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_BITMAP                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_BITOPS                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_BPF                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TEST_CLOCKSOURCE_WATCHDOG                policy<{'amd64': 'n'}>
+CONFIG_TEST_DIV64                               policy<{'amd64': 'n', 'amd64-lowlatency': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TEST_FIRMWARE                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_FPU                                 policy<{'amd64': 'n'}>
+CONFIG_TEST_FREE_PAGES                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_HASH                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_HEXDUMP                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_HMM                                 policy<{'amd64': 'n', 'arm64': 'n', 'ppc64el': 'n'}>
+CONFIG_TEST_IDA                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_KMOD                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_KSTRTOX                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_LIVEPATCH                           policy<{'amd64': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_LKM                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_LOCKUP                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_MEMCAT_P                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_MEMINIT                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_MIN_HEAP                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_OBJAGG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_OVERFLOW                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_PARMAN                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_POWER                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TEST_PRINTF                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_RHASHTABLE                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_SCANF                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_STACKINIT                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_STATIC_KEYS                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_STRING_HELPERS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_STRSCPY                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_SYSCTL                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_UBSAN                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_UDELAY                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_USER_COPY                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_UUID                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_VMALLOC                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEST_XARRAY                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TEXTSEARCH                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TEXTSEARCH_BM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TEXTSEARCH_FSM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TEXTSEARCH_KMP                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_THERMAL                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_THERMAL_DEFAULT_GOV_POWER_ALLOCATOR      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS      policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0'}>
+CONFIG_THERMAL_EMULATION                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_GOV_BANG_BANG                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_GOV_FAIR_SHARE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_GOV_POWER_ALLOCATOR              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_GOV_STEP_WISE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_GOV_USER_SPACE                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_HWMON                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_MMIO                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_THERMAL_NETLINK                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_OF                               policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_STATISTICS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THERMAL_WRITABLE_TRIPS                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THINKPAD_ACPI                            policy<{'amd64': 'm'}>
+CONFIG_THINKPAD_ACPI_ALSA_SUPPORT               policy<{'amd64': 'y'}>
+CONFIG_THINKPAD_ACPI_DEBUG                      policy<{'amd64': 'n'}>
+CONFIG_THINKPAD_ACPI_DEBUGFACILITIES            policy<{'amd64': 'y'}>
+CONFIG_THINKPAD_ACPI_HOTKEY_POLL                policy<{'amd64': 'y'}>
+CONFIG_THINKPAD_ACPI_UNSAFE_LEDS                policy<{'amd64': 'n'}>
+CONFIG_THINKPAD_ACPI_VIDEO                      policy<{'amd64': 'y'}>
+CONFIG_THINKPAD_LMI                             policy<{'amd64': 'm'}>
+CONFIG_THP_SWAP                                 policy<{'amd64': 'y'}>
+CONFIG_THREAD_INFO_IN_TASK                      policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_THREAD_SHIFT                             policy<{'ppc64el': '14'}>
+CONFIG_THRUSTMASTER_FF                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_THUMB2_KERNEL                            policy<{'armhf': 'n'}>
+CONFIG_THUNDERX2_PMU                            policy<{'arm64': 'm'}>
+CONFIG_THUNDER_NIC_BGX                          policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_THUNDER_NIC_PF                           policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_THUNDER_NIC_RGX                          policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_THUNDER_NIC_VF                           policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_TICK_CPU_ACCOUNTING                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TICK_ONESHOT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TIFM_7XX1                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TIFM_CORE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TIGON3                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TIGON3_HWMON                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TIMERFD                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TIMER_ACPI                               policy<{'arm64': 'y'}>
+CONFIG_TIMER_IMX_SYS_CTR                        policy<{'arm64': 'y'}>
+CONFIG_TIMER_OF                                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TIMER_PROBE                              policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TIME_NS                                  policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TINYDRM_HX8357D                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_ILI9225                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_ILI9341                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_ILI9486                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_MI0283QT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_REPAPER                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_ST7586                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TINYDRM_ST7735R                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TIPC                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TIPC_CRYPTO                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TIPC_DIAG                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TIPC_MEDIA_IB                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TIPC_MEDIA_UDP                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TI_ADC081C                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADC0832                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADC084S021                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADC108S102                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADC12138                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADC128S052                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADC161S626                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADS1015                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADS124S08                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADS131E08                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADS7950                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADS8344                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_ADS8688                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_AM335X_ADC                            policy<{'amd64': '-', 'arm64': 'm', 'armhf': 'm', 'ppc64el': '-'}>
+CONFIG_TI_AM65_CPSW_TAS                         policy<{'arm64': 'y'}>
+CONFIG_TI_CPPI41                                policy<{'armhf': 'm'}>
+CONFIG_TI_CPSW                                  policy<{'armhf': 'y'}>
+CONFIG_TI_CPSW_PHY_SEL                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_TI_CPSW_SWITCHDEV                        policy<{'armhf': 'm'}>
+CONFIG_TI_CPTS                                  policy<{'armhf': 'y'}>
+CONFIG_TI_DAC082S085                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_DAC5571                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_DAC7311                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_DAC7612                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_DAVINCI_EMAC                          policy<{'armhf-generic': 'm'}>
+CONFIG_TI_DAVINCI_MDIO                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_TI_DMA_CROSSBAR                          policy<{'armhf': 'y'}>
+CONFIG_TI_EDMA                                  policy<{'armhf': 'y'}>
+CONFIG_TI_EMIF                                  policy<{'armhf': 'm'}>
+CONFIG_TI_EMIF_SRAM                             policy<{'armhf-generic': 'm'}>
+CONFIG_TI_EQEP                                  policy<{'armhf-generic': 'm'}>
+CONFIG_TI_K3_AM65_CPSW_NUSS                     policy<{'arm64': 'm'}>
+CONFIG_TI_K3_AM65_CPSW_SWITCHDEV                policy<{'arm64': 'y'}>
+CONFIG_TI_K3_AM65_CPTS                          policy<{'arm64': 'm'}>
+CONFIG_TI_K3_DSP_REMOTEPROC                     policy<{'arm64': 'm'}>
+CONFIG_TI_K3_PSIL                               policy<{'arm64': 'y'}>
+CONFIG_TI_K3_R5_REMOTEPROC                      policy<{'arm64': 'm'}>
+CONFIG_TI_K3_RINGACC                            policy<{'arm64': 'y'}>
+CONFIG_TI_K3_SOCINFO                            policy<{'arm64': 'y'}>
+CONFIG_TI_K3_UDMA                               policy<{'arm64': 'y'}>
+CONFIG_TI_K3_UDMA_GLUE_LAYER                    policy<{'arm64': 'y'}>
+CONFIG_TI_MESSAGE_MANAGER                       policy<{'arm64': 'y'}>
+CONFIG_TI_PIPE3                                 policy<{'armhf': 'm'}>
+CONFIG_TI_PRUSS                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_TI_PRUSS_INTC                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_TI_PWMSS                                 policy<{'armhf-generic': 'y'}>
+CONFIG_TI_SCI_CLK                               policy<{'arm64': 'm'}>
+CONFIG_TI_SCI_CLK_PROBE_FROM_FW                 policy<{'arm64': 'n'}>
+CONFIG_TI_SCI_INTA_IRQCHIP                      policy<{'arm64': 'y'}>
+CONFIG_TI_SCI_INTA_MSI_DOMAIN                   policy<{'arm64': 'y'}>
+CONFIG_TI_SCI_INTR_IRQCHIP                      policy<{'arm64': 'y'}>
+CONFIG_TI_SCI_PM_DOMAINS                        policy<{'arm64': 'm'}>
+CONFIG_TI_SCI_PROTOCOL                          policy<{'arm64': 'y'}>
+CONFIG_TI_SOC_THERMAL                           policy<{'arm64': '-', 'armhf': 'm', 'ppc64el': '-'}>
+CONFIG_TI_ST                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TI_SYSC                                  policy<{'armhf': 'y'}>
+CONFIG_TI_SYSCON_CLK                            policy<{'arm64': 'y'}>
+CONFIG_TI_THERMAL                               policy<{'armhf': 'y'}>
+CONFIG_TI_TLC4541                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TI_TSC2046                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TLAN                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TLS                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TLS_DEVICE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TLS_TOE                                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TMD_HERMES                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TMP006                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TMP007                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TMP117                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TMPFS                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TMPFS_INODE64                            policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TMPFS_XATTR                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TN3215                                   policy<{'s390x': 'y'}>
+CONFIG_TN3215_CONSOLE                           policy<{'s390x': 'y'}>
+CONFIG_TN3270                                   policy<{'s390x': 'y'}>
+CONFIG_TN3270_CONSOLE                           policy<{'s390x': 'y'}>
+CONFIG_TN3270_FS                                policy<{'s390x': 'm'}>
+CONFIG_TN3270_TTY                               policy<{'s390x': 'y'}>
+CONFIG_TOPSTAR_LAPTOP                           policy<{'amd64': 'm'}>
+CONFIG_TOSHIBA_BT_RFKILL                        policy<{'amd64': 'm'}>
+CONFIG_TOSHIBA_HAPS                             policy<{'amd64': 'm'}>
+CONFIG_TOSHIBA_WMI                              policy<{'amd64': 'n'}>
+CONFIG_TOUCHSCREEN_88PM860X                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_AD7877                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_AD7879                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_AD7879_I2C                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_AD7879_SPI                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ADC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ADS7846                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_AR1021_I2C                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ATMEL_MXT                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ATMEL_MXT_T37                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_AUO_PIXCIR                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_BU21013                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_BU21029                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CHIPONE_ICN8318              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CHIPONE_ICN8505              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_TOUCHSCREEN_COLIBRI_VF50                 policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CY8CTMA140                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CY8CTMG110                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CYTTSP4_CORE                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CYTTSP4_I2C                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CYTTSP4_SPI                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CYTTSP_CORE                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CYTTSP_I2C                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_CYTTSP_SPI                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_DA9034                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_DA9052                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_DMI                          policy<{'amd64': 'y'}>
+CONFIG_TOUCHSCREEN_DYNAPRO                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_EDT_FT5X06                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_EETI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_EGALAX                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_EGALAX_SERIAL                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_EKTF2127                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ELO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_EXC3000                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_FUJITSU                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_GOODIX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_GUNZE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_HAMPSHIRE                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_HIDEEP                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_HYCON_HY46XX                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ILI210X                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ILITEK                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_IMX6UL_TSC                   policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_INEXIO                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_IPROC                        policy<{'arm64': 'm'}>
+CONFIG_TOUCHSCREEN_IQS5XX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MAX11801                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MC13783                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MCS5000                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MELFAS_MIP4                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MK712                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MMS114                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MSG2638                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_MTOUCH                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_PCAP                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_PENMOUNT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_PIXCIR                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_RASPBERRYPI_FW               policy<{'arm64': 'm'}>
+CONFIG_TOUCHSCREEN_RM_TS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ROHM_BU21023                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_S6SY761                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_SILEAD                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_SIS_I2C                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ST1232                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_STMFTS                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_STMPE                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_SUN4I                        policy<{'arm64': 'n'}>
+CONFIG_TOUCHSCREEN_SUR40                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_SURFACE3_SPI                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_SX8654                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TI_AM335X_TSC                policy<{'amd64': '-', 'arm64': 'm', 'armhf': 'm', 'ppc64el': '-'}>
+CONFIG_TOUCHSCREEN_TOUCHIT213                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TOUCHRIGHT                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TOUCHWIN                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TPS6507X                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TS4800                       policy<{'armhf-generic': 'm'}>
+CONFIG_TOUCHSCREEN_TSC2004                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TSC2005                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TSC2007                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TSC2007_IIO                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_TSC200X_CORE                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_TSC_SERIO                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_UCB1400                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_USB_3M                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_COMPOSITE                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_USB_DMC_TSC10                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_E2I                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_EASYTOUCH                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_EGALAX                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_ELO                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_ETT_TC45USB              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_ETURBO                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_GENERAL_TOUCH            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_GOTOP                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_GUNZE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_IDEALTEK                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_IRTOUCH                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_ITM                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_JASTEC                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_NEXIO                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_PANJIT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_USB_ZYTRONIC                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_WACOM_I2C                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_WACOM_W8001                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_WDT87XX_I2C                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_WM831X                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_WM9705                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_WM9712                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_WM9713                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TOUCHSCREEN_WM97XX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ZET6223                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ZFORCE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TOUCHSCREEN_ZINITIX                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TPL0102                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TPM_KEY_PARSER                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_TPS6105X                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TPS65010                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TPS6507X                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_TPS68470_PMIC_OPREGION                   policy<{'amd64': 'y'}>
+CONFIG_TQMX86_WDT                               policy<{'amd64': 'm'}>
+CONFIG_TRACEPOINTS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACEPOINT_BENCHMARK                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TRACER_MAX_TRACE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACER_SNAPSHOT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACER_SNAPSHOT_PER_CPU_SWAP             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TRACE_CLOCK                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACE_EVAL_MAP_FILE                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TRACE_EVENT_INJECT                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACE_IRQFLAGS_NMI_SUPPORT               policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_TRACE_IRQFLAGS_SUPPORT                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACING                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACING_MAP                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRACING_SUPPORT                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRANSPARENT_HUGEPAGE                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS              policy<{'amd64': 'n', 'arm64': 'n', 'armhf-generic-lpae': 'n', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_TRANSPARENT_HUGEPAGE_MADVISE             policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_TREE_RCU                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TREE_SRCU                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TRIM_UNUSED_KSYMS                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TRUSTED_FOUNDATIONS                      policy<{'armhf': 'y'}>
+CONFIG_TRUSTED_KEYS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TS4800_IRQ                               policy<{'armhf-generic': 'm'}>
+CONFIG_TS4800_WATCHDOG                          policy<{'armhf-generic': 'm'}>
+CONFIG_TSL2583                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TSL2591                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TSL2772                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TSL4531                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TSYS01                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TSYS02D                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TTPCI_EEPROM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TTY                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TTY_PRINTK                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_TTY_PRINTK_LEVEL                         policy<{'amd64': '6', 'arm64': '6', 'armhf': '6', 'ppc64el': '6'}>
+CONFIG_TULIP                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TULIP_MMIO                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_TULIP_MWI                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_TULIP_NAPI                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_TUN                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_TUNE_DEFAULT                             policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z10                                 policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z13                                 policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z14                                 policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z15                                 policy<{'s390x': 'y'}>
+CONFIG_TUNE_Z196                                policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z900                                policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z990                                policy<{'s390x': 'n'}>
+CONFIG_TUNE_Z9_109                              policy<{'s390x': 'n'}>
+CONFIG_TUNE_ZEC12                               policy<{'s390x': 'n'}>
+CONFIG_TUN_VNET_CROSS_LE                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_TURRIS_MOX_RWTM                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_TWL4030_CORE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TWL4030_MADC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TWL4030_POWER                            policy<{'armhf': 'y'}>
+CONFIG_TWL4030_USB                              policy<{'armhf': 'm'}>
+CONFIG_TWL4030_WATCHDOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TWL6030_GPADC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TWL6030_USB                              policy<{'armhf': 'm'}>
+CONFIG_TWL6040_CORE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_TYPEC                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_DP_ALTMODE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_FUSB302                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_HD3SS3220                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_MT6360                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_MUX_INTEL_PMC                      policy<{'amd64': 'm'}>
+CONFIG_TYPEC_MUX_PI3USB30532                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_NVIDIA_ALTMODE                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_QCOM_PMIC                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_TYPEC_RT1711H                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_STUSB160X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_TCPCI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_TCPCI_MAXIM                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_TCPM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_TPS6598X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_UCSI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_TYPEC_WCOVE                              policy<{'amd64': 'n'}>
+CONFIG_TYPHOON                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_UACCE                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UACCESS_WITH_MEMCPY                      policy<{'armhf': 'n'}>
+CONFIG_UBIFS_ATIME_SUPPORT                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_UBIFS_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_UBIFS_FS_ADVANCED_COMPR                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_UBIFS_FS_AUTHENTICATION                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UBIFS_FS_LZO                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UBIFS_FS_SECURITY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UBIFS_FS_XATTR                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UBIFS_FS_ZLIB                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UBIFS_FS_ZSTD                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UBSAN_ALIGNMENT                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_UBSAN_BOOL                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN_BOUNDS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN_DIV_ZERO                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_UBSAN_ENUM                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN_ONLY_BOUNDS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN_SANITIZE_ALL                       policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN_SHIFT                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UBSAN_TRAP                               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_UBSAN_UNREACHABLE                        policy<{'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_UBUNTU_HOST                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_UBUNTU_ODM_DRIVERS                       policy<{'amd64': 'y'}>
+CONFIG_UCB1400_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_UCC                                      policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UCC_FAST                                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UCC_SLOW                                 policy<{'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UCLAMP_BUCKETS_COUNT                     policy<{'amd64': '5', 'arm64': '5', 'armhf': '5', 'ppc64el': '5'}>
+CONFIG_UCLAMP_TASK                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UCLAMP_TASK_GROUP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UCS2_STRING                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y'}>
+CONFIG_UCSI_ACPI                                policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_UCSI_CCG                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_UDBG_RTAS_CONSOLE                        policy<{'ppc64el': 'n'}>
+CONFIG_UDF_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_UDMABUF                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UEFI_CPER                                policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_UEFI_CPER_ARM                            policy<{'arm64': 'y'}>
+CONFIG_UEFI_CPER_X86                            policy<{'amd64': 'y'}>
+CONFIG_UEVENT_HELPER                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UEVENT_HELPER_PATH                       policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_UFS_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_UFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UFS_FS_WRITE                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_UHID                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_UID16                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 's390x': 'y'}>
+CONFIG_UIO                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_UIO_AEC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_CIF                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_DFL                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_UIO_DMEM_GENIRQ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_FSL_ELBC_GPCM                        policy<{'ppc64el': 'm'}>
+CONFIG_UIO_FSL_ELBC_GPCM_NETX5152               policy<{'ppc64el': 'n'}>
+CONFIG_UIO_HV_GENERIC                           policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_UIO_MF624                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_NETX                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_PCI_GENERIC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_PDRV_GENIRQ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_PRUSS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_UIO_SERCOS3                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ULI526X                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ULTRIX_PARTITION                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_UNCOMPRESS_INCLUDE                       policy<{'armhf': '"debug/uncompress.h"'}>
+CONFIG_UNICODE                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UNICODE_NORMALIZATION_SELFTEST           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_UNINLINE_SPIN_UNLOCK                     policy<{'amd64-lowlatency': 'y', 'arm64-lowlatency': 'y', 'arm64-lowlatency-64k': 'y'}>
+CONFIG_UNIPHIER_EFUSE                           policy<{'armhf': 'm'}>
+CONFIG_UNIPHIER_MDMAC                           policy<{'armhf': 'm'}>
+CONFIG_UNIPHIER_SYSTEM_BUS                      policy<{'armhf': 'y'}>
+CONFIG_UNIPHIER_THERMAL                         policy<{'armhf': 'm'}>
+CONFIG_UNIPHIER_WATCHDOG                        policy<{'armhf': 'm'}>
+CONFIG_UNIPHIER_XDMAC                           policy<{'armhf': 'm'}>
+CONFIG_UNISYSSPAR                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_UNISYS_VISORBUS                          policy<{'amd64': 'm'}>
+CONFIG_UNISYS_VISORHBA                          policy<{'amd64': 'm'}>
+CONFIG_UNISYS_VISORINPUT                        policy<{'amd64': 'm'}>
+CONFIG_UNISYS_VISORNIC                          policy<{'amd64': 'm'}>
+CONFIG_UNIX                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UNIX98_PTYS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UNIXWARE_DISKLABEL                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_UNIX_DIAG                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_UNIX_SCM                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UNMAP_KERNEL_AT_EL0                      policy<{'arm64': 'y'}>
+CONFIG_UNWINDER_GUESS                           policy<{'amd64': 'n'}>
+CONFIG_UNWINDER_ORC                             policy<{'amd64': 'n'}>
+CONFIG_UPROBES                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UPROBE_EVENTS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_US5182D                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB4                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_USB4_DEBUGFS_WRITE                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB4_DMA_TEST                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB4_NET                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USBIP_CORE                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USBIP_DEBUG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USBIP_HOST                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USBIP_VHCI_HCD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USBIP_VHCI_HC_PORTS                      policy<{'amd64': '8', 'arm64': '8', 'armhf': '8', 'ppc64el': '8'}>
+CONFIG_USBIP_VHCI_NR_HCS                        policy<{'amd64': '1', 'arm64': '1', 'armhf': '1', 'ppc64el': '1'}>
+CONFIG_USBIP_VUDC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USBPCWATCHDOG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ACM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ADUTUX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_AIRSPY                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ALI_M5632                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_AMD5536UDC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_AN2720                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ANNOUNCE_NEW_DEVICES                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_APPLEDISPLAY                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ARCH_HAS_HCD                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ARMLINUX                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ASPEED_VHUB                          policy<{'armhf': 'm'}>
+CONFIG_USB_ATM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_AUDIO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_AUTOSUSPEND_DELAY                    policy<{'amd64': '2', 'arm64': '2', 'armhf': '2', 'ppc64el': '2'}>
+CONFIG_USB_BDC_UDC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_BELKIN                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_BRCMSTB                              policy<{'arm64': 'm'}>
+CONFIG_USB_C67X00_HCD                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CATC                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CDC_COMPOSITE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CDC_PHONET                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CDNS3                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CDNS3_GADGET                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CDNS3_HOST                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CDNS3_IMX                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_USB_CDNS3_PCI_WRAP                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_USB_CDNS3_TI                             policy<{'arm64': 'm'}>
+CONFIG_USB_CDNSP_GADGET                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_USB_CDNSP_HOST                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_USB_CDNSP_PCI                            policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_USB_CDNS_HOST                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CDNS_SUPPORT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHAOSKEY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA_GENERIC                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA_HOST                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CHIPIDEA_IMX                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA_MSM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA_PCI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA_TEGRA                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CHIPIDEA_UDC                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_COMMON                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CONFIGFS_ACM                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_ECM                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_ECM_SUBSET                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_EEM                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_FS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_HID                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_LB_SS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_MIDI                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_PRINTER                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_TCM                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_UAC1                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_UAC1_LEGACY               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_UAC2                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_F_UVC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_MASS_STORAGE                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_NCM                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_OBEX                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_PHONET                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_RNDIS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONFIGFS_SERIAL                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_CONN_GPIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CXACRU                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CYPRESS_CY7C63                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_CYTHERM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_DEFAULT_PERSIST                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_DSBR                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_DUMMY_HCD                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_DWC2                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_DWC2_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_DWC2_DUAL_ROLE                       policy<{'armhf': 'n'}>
+CONFIG_USB_DWC2_HOST                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_DWC2_PCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_USB_DWC2_PERIPHERAL                      policy<{'armhf': 'n'}>
+CONFIG_USB_DWC2_TRACK_MISSED_SOFS               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_DWC3                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_DWC3_DUAL_ROLE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_DWC3_EXYNOS                          policy<{'armhf': 'm'}>
+CONFIG_USB_DWC3_GADGET                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_DWC3_HAPS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_DWC3_HOST                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_DWC3_IMX8MP                          policy<{'arm64': 'm'}>
+CONFIG_USB_DWC3_KEYSTONE                        policy<{'arm64': 'm'}>
+CONFIG_USB_DWC3_MESON_G12A                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_DWC3_OF_SIMPLE                       policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_DWC3_OMAP                            policy<{'armhf': 'm'}>
+CONFIG_USB_DWC3_PCI                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_USB_DWC3_QCOM                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_DWC3_ULPI                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_DWC3_XILINX                          policy<{'arm64': 'm'}>
+CONFIG_USB_DYNAMIC_MINORS                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_EG20T                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_EHCI_BRCMSTB                         policy<{'arm64': 'm'}>
+CONFIG_USB_EHCI_EXYNOS                          policy<{'armhf': 'y'}>
+CONFIG_USB_EHCI_FSL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_EHCI_HCD_NPCM7XX                     policy<{'armhf': 'm'}>
+CONFIG_USB_EHCI_HCD_OMAP                        policy<{'armhf': 'm'}>
+CONFIG_USB_EHCI_HCD_ORION                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_USB_EHCI_HCD_PPC_OF                      policy<{'ppc64el': 'y'}>
+CONFIG_USB_EHCI_PCI                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_EHCI_ROOT_HUB_TT                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_EHCI_TEGRA                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_USB_EHCI_TT_NEWSCHED                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_EHSET_TEST_FIXTURE                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_EMI26                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_EMI62                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_EMXX                                 policy<{'arm64': 'm', 'armhf': 'y'}>
+CONFIG_USB_EPSON2888                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ETH                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ETH_EEM                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ETH_RNDIS                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_EZUSB_FX2                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_FEW_INIT_RETRIES                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_FHCI_HCD                             policy<{'ppc64el': 'm'}>
+CONFIG_USB_FOTG210_HCD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_FOTG210_UDC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_FTDI_ELAN                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_FUNCTIONFS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_FUNCTIONFS_ETH                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_FUNCTIONFS_GENERIC                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_FUNCTIONFS_RNDIS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_FUSB300                              policy<{'armhf-generic': 'm'}>
+CONFIG_USB_F_ACM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_ECM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_EEM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_FS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_HID                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_MASS_STORAGE                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_MIDI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_NCM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_OBEX                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_PHONET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_PRINTER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_RNDIS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_SERIAL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_SS_LB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_SUBSET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_TCM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_UAC1                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_UAC1_LEGACY                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_UAC2                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_F_UVC                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GADGET                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'y', 'ppc64el': 'm'}>
+CONFIG_USB_GADGETFS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GADGET_DEBUG                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_GADGET_DEBUG_FILES                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_GADGET_DEBUG_FS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS           policy<{'amd64': '2', 'arm64': '2', 'armhf': '2', 'ppc64el': '2'}>
+CONFIG_USB_GADGET_TARGET                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GADGET_VBUS_DRAW                     policy<{'amd64': '2', 'arm64': '2', 'armhf': '2', 'ppc64el': '2'}>
+CONFIG_USB_GADGET_XILINX                        policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GL860                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GOKU                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GPIO_VBUS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GR_UDC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_BENQ                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_CONEX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_CPIA1                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_DTCS033                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_ETOMS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_FINEPIX                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_JEILINJ                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_JL2005BCD                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_KINECT                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_KONICA                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_MARS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_MR97310A                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_NW80X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_OV519                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_OV534                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_OV534_9                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_PAC207                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_PAC7302                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_PAC7311                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SE401                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SN9C2028                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SN9C20X                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SONIXB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SONIXJ                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA1528                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA500                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA501                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA505                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA506                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA508                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SPCA561                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SQ905                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SQ905C                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SQ930X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_STK014                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_STK1135                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_STV0680                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_SUNPLUS                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_T613                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_TOPRO                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_TOUPTEK                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_TV8532                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_VC032X                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_VICAM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_XIRLINK_CIT                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_GSPCA_ZC3XX                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_ACM_MS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_DBGP                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_DBGP_PRINTK                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_G_DBGP_SERIAL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_G_HID                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_MULTI                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'm', 'ppc64el': 'n'}>
+CONFIG_USB_G_MULTI_CDC                          policy<{'armhf': 'y'}>
+CONFIG_USB_G_MULTI_RNDIS                        policy<{'armhf': 'y'}>
+CONFIG_USB_G_NCM                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_NOKIA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_PRINTER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_SERIAL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_G_WEBCAM                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_HACKRF                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_HCD_TEST_MODE                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_HID                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_HIDDEV                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_HSIC_USB3503                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_HSIC_USB4604                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_HSO                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_HUB_USB251XB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_IDMOUSE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_IOWARRIOR                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_IPHETH                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ISIGHTFW                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ISP116X_HCD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ISP1301                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ISP1760                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ISP1760_DUAL_ROLE                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ISP1760_GADGET_ROLE                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_ISP1760_HCD                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_ISP1760_HOST_ROLE                    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_ISP1761_UDC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_KAWETH                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_KBD                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_KC2190                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_KEENE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LAN78XX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LCD                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LD                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LEDS_TRIGGER_USBPORT                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LED_TRIG                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_LEGOTOWER                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LGM_PHY                              policy<{'amd64': 'm'}>
+CONFIG_USB_LIBCOMPOSITE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_LINK_LAYER_TEST                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_M5602                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MA901                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MASS_STORAGE                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MAX3420_UDC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MAX3421_HCD                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MDC800                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MICROTEK                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MIDI_GADGET                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MON                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MOUSE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MR800                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MSI2500                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MTU3                                 policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_MTU3_DEBUG                           policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_USB_MTU3_DUAL_ROLE                       policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_USB_MTU3_GADGET                          policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_USB_MTU3_HOST                            policy<{'arm64': 'n', 'armhf': 'n'}>
+CONFIG_USB_MUSB_AM35X                           policy<{'armhf': 'm'}>
+CONFIG_USB_MUSB_DSPS                            policy<{'armhf': 'm'}>
+CONFIG_USB_MUSB_DUAL_ROLE                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_MUSB_GADGET                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_MUSB_HOST                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_MUSB_MEDIATEK                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_MUSB_OMAP2PLUS                       policy<{'armhf': 'm'}>
+CONFIG_USB_MUSB_SUNXI                           policy<{'arm64': 'm'}>
+CONFIG_USB_MUSB_TUSB6010                        policy<{'armhf': 'm'}>
+CONFIG_USB_MV_U3D                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MV_UDC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_MXS_PHY                              policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_USB_NET2272                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET2272_DMA                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_NET2280                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_AQC111                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_AX88179_178A                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_AX8817X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CDCETHER                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CDC_EEM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CDC_MBIM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CDC_NCM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CDC_SUBSET                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CDC_SUBSET_ENABLE                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CH9200                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_CX82310_ETH                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_DM9601                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_DRIVERS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_GL620A                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_HUAWEI_CDC_NCM                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_INT51X1                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_KALMIA                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_MCS7830                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_NET1080                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_PLUSB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_QMI_WWAN                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_RNDIS_HOST                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_RNDIS_WLAN                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_SMSC75XX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_SMSC95XX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_SR9700                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_SR9800                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_NET_ZAURUS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_OHCI_EXYNOS                          policy<{'armhf': 'y'}>
+CONFIG_USB_OHCI_HCD_OMAP3                       policy<{'armhf-generic': 'm'}>
+CONFIG_USB_OHCI_HCD_PCI                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_OHCI_HCD_PLATFORM                    policy<{'amd64': 'y', 'arm64': 'm', 'armhf-generic': 'm', 'armhf-generic-lpae': 'n', 'ppc64el': 'm'}>
+CONFIG_USB_OHCI_HCD_PPC_OF_BE                   policy<{'ppc64el': 'n'}>
+CONFIG_USB_OHCI_HCD_PPC_OF_LE                   policy<{'ppc64el': 'n'}>
+CONFIG_USB_OHCI_LITTLE_ENDIAN                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_USB_OTG_DISABLE_EXTERNAL_HUB             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_OTG_PRODUCTLIST                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_OXU210HP_HCD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_PCI                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_PEGASUS                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_PHY                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_PRINTER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_PULSE8_CEC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_PWC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_PWC_DEBUG                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_PWC_INPUT_EVDEV                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_PXA27X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_R8A66597                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_R8A66597_HCD                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_RAINSHADOW_CEC                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_RAREMONO                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_RAW_GADGET                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_RENESAS_USB3                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_RENESAS_USBHS                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_RENESAS_USBHS_HCD                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_RENESAS_USBHS_UDC                    policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_ROLES_INTEL_XHCI                     policy<{'amd64': 'm'}>
+CONFIG_USB_ROLE_SWITCH                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_RTL8150                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_RTL8152                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_RTL8153_ECM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_S2255                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_AIRCABLE                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_ARK3116                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_BELKIN                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_CH341                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_CP210X                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_CYBERJACK                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_CYPRESS_M8                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_EDGEPORT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_EDGEPORT_TI                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_EMPEG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_F81232                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_F8153X                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_FTDI_SIO                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_GARMIN                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_GENERIC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_SERIAL_IPAQ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_IPW                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_IR                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_IUU                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_KEYSPAN                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_KEYSPAN_PDA                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_KLSI                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_KOBIL_SCT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_MCT_U232                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_METRO                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_MOS7715_PARPORT               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_SERIAL_MOS7720                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_MOS7840                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_MXUPORT                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_NAVMAN                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_OMNINET                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_OPTICON                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_OPTION                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_OTI6858                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_PL2303                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_QCAUX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_QT2                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_QUALCOMM                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_SAFE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_SAFE_PADDED                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_SERIAL_SIERRAWIRELESS                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_SIMPLE                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_SPCP8X5                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_SSU100                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_SYMBOL                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_TI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_UPD78F0730                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_VISOR                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_WHITEHEAT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_WISHBONE                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_WWAN                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_XR                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SERIAL_XSENS_MT                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SEVSEG                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SI470X                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SI4713                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SIERRA_NET                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SISUSBVGA                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SL811_CS                             policy<{'amd64': 'm'}>
+CONFIG_USB_SL811_HCD                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SL811_HCD_ISO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_SNP_CORE                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SNP_UDC_PLAT                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SPEEDTOUCH                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STKWEBCAM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_ALAUDA                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_CYPRESS_ATACB                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_DATAFAB                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_DEBUG                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_USB_STORAGE_ENE_UB6250                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_FREECOM                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_ISD200                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_JUMPSHOT                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_KARMA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_ONETOUCH                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_REALTEK                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_SDDR09                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_SDDR55                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STORAGE_USBAT                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_STV06XX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_SUPPORT                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_USB_TEGRA_PHY                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_USB_TEGRA_XUDC                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_USB_TEST                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_TMC                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_TRANCEVIBRATOR                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_U132_HCD                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_UAS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_UEAGLEATM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_UHCI_ASPEED                          policy<{'armhf': 'y'}>
+CONFIG_USB_UHCI_PLATFORM                        policy<{'armhf': 'y'}>
+CONFIG_USB_UHCI_SUPPORT_NON_PCI_HC              policy<{'armhf': 'y'}>
+CONFIG_USB_ULPI                                 policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_USB_ULPI_BUS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ULPI_VIEWPORT                        policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_USB_USBNET                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_USS720                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_U_AUDIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_U_ETHER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_U_SERIAL                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_VIDEO_CLASS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_USB_VL600                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_WDM                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_XHCI_HISTB                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_XHCI_MTK                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_XHCI_MVEBU                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_XHCI_PCI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_XHCI_PCI_RENESAS                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_XHCI_PLATFORM                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_XHCI_RCAR                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_USB_XHCI_TEGRA                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_USB_XUSBATM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_YUREX                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ZD1201                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ZERO                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USB_ZR364XX                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USELIB                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_USERFAULTFD                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_USERIO                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_USERMODE_DRIVER                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_USER_NS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_USER_RETURN_NOTIFIER                     policy<{'amd64': 'y'}>
+CONFIG_USER_STACKTRACE_SUPPORT                  policy<{'amd64': 'y'}>
+CONFIG_USE_OF                                   policy<{'armhf': 'y'}>
+CONFIG_USE_PERCPU_NUMA_NODE_ID                  policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_UTS_NS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_UV_MMTIMER                               policy<{'amd64': 'm'}>
+CONFIG_UV_SYSFS                                 policy<{'amd64': 'm'}>
+CONFIG_U_SERIAL_CONSOLE                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_V4L2_ASYNC                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_V4L2_FLASH_LED_CLASS                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_V4L2_FWNODE                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_V4L2_H264                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_V4L2_JPEG_HELPER                         policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_V4L2_MEM2MEM_DEV                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_V4L_MEM2MEM_DRIVERS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_V4L_PLATFORM_DRIVERS                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_V4L_TEST_DRIVERS                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VALIDATE_FS_PARSER                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VBOXGUEST                                policy<{'amd64': 'm'}>
+CONFIG_VBOXSF_FS                                policy<{'amd64': 'm'}>
+CONFIG_VCHIQ_CDEV                               policy<{'arm64': 'y'}>
+CONFIG_VCNL3020                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VCNL4000                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VCNL4035                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VDPA                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_VDPA_SIM                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VDPA_SIM_BLOCK                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VDPA_SIM_NET                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VDPA_USER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VDSO                                     policy<{'armhf': 'y'}>
+CONFIG_VDSO32                                   policy<{'ppc64el': 'y'}>
+CONFIG_VEML6030                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VEML6070                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VERSION_SIGNATURE                        policy<{'amd64': '""', 'arm64': '""', 'armhf': '""', 'ppc64el': '""', 's390x': '""'}>
+CONFIG_VETH                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VEXPRESS_CONFIG                          policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_VF610_ADC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VF610_DAC                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VFIO_AMBA                                policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VFIO_AP                                  policy<{'s390x': 'm'}>
+CONFIG_VFIO_CCW                                 policy<{'s390x': 'm'}>
+CONFIG_VFIO_FSL_MC                              policy<{'arm64': 'm'}>
+CONFIG_VFIO_IOMMU_SPAPR_TCE                     policy<{'ppc64el': 'y'}>
+CONFIG_VFIO_IOMMU_TYPE1                         policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 's390x': 'm'}>
+CONFIG_VFIO_MDEV                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VFIO_NOIOMMU                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VFIO_PCI_CORE                            policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_VFIO_PCI_IGD                             policy<{'amd64': 'y'}>
+CONFIG_VFIO_PCI_INTX                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VFIO_PCI_MMAP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VFIO_PCI_VGA                             policy<{'amd64': 'y'}>
+CONFIG_VFIO_PLATFORM                            policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VFIO_PLATFORM_AMDXGBE_RESET              policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VFIO_PLATFORM_BCMFLEXRM_RESET            policy<{'arm64': 'm'}>
+CONFIG_VFIO_PLATFORM_CALXEDAXGMAC_RESET         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VFIO_SPAPR_EEH                           policy<{'ppc64el': 'y'}>
+CONFIG_VFIO_VIRQFD                              policy<{'amd64': 'y', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'y', 's390x': 'm'}>
+CONFIG_VFP                                      policy<{'armhf': 'y'}>
+CONFIG_VFPv3                                    policy<{'armhf': 'y'}>
+CONFIG_VF_USE_ARM_GLOBAL_TIMER                  policy<{'armhf-generic': 'y'}>
+CONFIG_VF_USE_PIT_TIMER                         policy<{'armhf-generic': 'n'}>
+CONFIG_VGASTATE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VGA_ARB                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VGA_ARB_MAX_GPUS                         policy<{'amd64': '16', 'arm64': '16', 'armhf': '16', 'ppc64el': '16'}>
+CONFIG_VGA_CONSOLE                              policy<{'amd64': 'y', 'ppc64el': 'y'}>
+CONFIG_VGA_SWITCHEROO                           policy<{'amd64': 'y'}>
+CONFIG_VHOST                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VHOST_CROSS_ENDIAN_LEGACY                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_VHOST_IOTLB                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VHOST_MENU                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VHOST_NET                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VHOST_RING                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VHOST_SCSI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VHOST_VDPA                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VHOST_VSOCK                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIA_RHINE                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIA_RHINE_MMIO                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIA_VELOCITY                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIA_WDT                                  policy<{'amd64': 'm'}>
+CONFIG_VIDEOBUF2_CORE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF2_DMA_CONTIG                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF2_DMA_SG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF2_DVB                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF2_MEMOPS                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF2_V4L2                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF2_VMALLOC                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF_DMA_SG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF_GEN                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOBUF_VMALLOC                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEOMODE_HELPERS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_AD5820                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_AD9389B                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADP1653                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7170                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7175                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7180                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7183                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7343                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7393                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV748X                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7511                            policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ADV7511_CEC                        policy<{'amd64': 'y'}>
+CONFIG_VIDEO_ADV7604                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7604_CEC                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_ADV7842                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ADV7842_CEC                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_ADV_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_VIDEO_AK7375                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_AK881X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ALLEGRO_DVT                        policy<{'arm64': 'm'}>
+CONFIG_VIDEO_APTINA_PLL                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ASPEED                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ATOMISP                            policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_GC0310                     policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_GC2235                     policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_ISP2401                    policy<{'amd64': 'n'}>
+CONFIG_VIDEO_ATOMISP_LM3554                     policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_MSRLIST_HELPER             policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_MT9M114                    policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_OV2680                     policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_OV2722                     policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ATOMISP_OV5693                     policy<{'amd64': 'm'}>
+CONFIG_VIDEO_AU0828                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_AU0828_RC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_AU0828_V4L2                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_BCM2835                            policy<{'arm64': 'm'}>
+CONFIG_VIDEO_BT819                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_BT848                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_BT856                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_BT866                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CADENCE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_CADENCE_CSI2RX                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CADENCE_CSI2TX                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CAFE_CCIC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CCS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CCS_PLL                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_COBALT                             policy<{'amd64': 'm'}>
+CONFIG_VIDEO_CODA                               policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_VIDEO_CPIA2                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CS3308                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CS5345                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CS53L32A                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX18                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX18_ALSA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX231XX                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX231XX_ALSA                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX231XX_DVB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX231XX_RC                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_CX2341X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX23885                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX25821                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX25821_ALSA                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX25840                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX88                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX88_ALSA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX88_BLACKBIRD                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX88_DVB                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX88_ENABLE_VP3054                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_CX88_MPEG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_CX88_VP3054                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_DEV                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_DT3155                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_DW9714                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_DW9768                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_DW9807_VCM                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_EM28XX                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_EM28XX_ALSA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_EM28XX_DVB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_EM28XX_RC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_EM28XX_V4L2                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ET8EK8                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_FB_IVTV                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_FB_IVTV_FORCE_PAT                  policy<{'amd64': 'y'}>
+CONFIG_VIDEO_FIXED_MINOR_RANGES                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_VIDEO_GO7007                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_GO7007_LOADER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_GO7007_USB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_GO7007_USB_S2250_BOARD             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_GS1662                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_HANTRO                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_HANTRO_IMX8M                       policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_VIDEO_HANTRO_ROCKCHIP                    policy<{'arm64': 'y', 'armhf': 'y'}>
+CONFIG_VIDEO_HDPVR                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_HEXIUM_GEMINI                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_HEXIUM_ORION                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_HI556                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_HM11B1                             policy<{'amd64': 'm'}>
+CONFIG_VIDEO_I2C                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX208                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX214                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX219                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX258                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX274                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX290                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX319                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX334                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX335                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX355                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX412                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IMX7_CSI                           policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_VIDEO_IMX8_JPEG                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_VIDEO_IMX_CSI                            policy<{'armhf-generic': 'm'}>
+CONFIG_VIDEO_IMX_MEDIA                          policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_VIDEO_IMX_PXP                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_VIDEO_IMX_VDOA                           policy<{'armhf-generic': 'm'}>
+CONFIG_VIDEO_INTEL_IPU6                         policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_VIDEO_IPU3_CIO2                          policy<{'amd64': 'm'}>
+CONFIG_VIDEO_IPU3_IMGU                          policy<{'amd64': 'm'}>
+CONFIG_VIDEO_IR_I2C                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IVTV                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_IVTV_ALSA                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_KS0127                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_LM3560                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_LM3646                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_M52790                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_M5MOLS                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MAX9271_LIB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MAX9286                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MEDIATEK_VPU                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_MEM2MEM_DEINTERLACE                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MESON_GE2D                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_MESON_VDEC                         policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_MEYE                               policy<{'amd64': 'm'}>
+CONFIG_VIDEO_ML86V7667                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MSP3400                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9M001                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9M032                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9M111                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9P031                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9T001                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9T112                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9V011                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9V032                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MT9V111                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MUX                                policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_MXB                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_NOON010PC30                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OMAP2_VOUT                         policy<{'armhf-generic': 'm'}>
+CONFIG_VIDEO_OMAP2_VOUT_VRFB                    policy<{'armhf-generic': 'y'}>
+CONFIG_VIDEO_OMAP3                              policy<{'armhf-generic': 'm'}>
+CONFIG_VIDEO_OMAP3_DEBUG                        policy<{'armhf-generic': 'n'}>
+CONFIG_VIDEO_OMAP4                              policy<{'armhf-generic': 'm'}>
+CONFIG_VIDEO_OV01A10                            policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_VIDEO_OV01A1S                            policy<{'amd64': 'm'}>
+CONFIG_VIDEO_OV02A10                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV02C10                            policy<{'amd64': 'm', 'arm64': 'n'}>
+CONFIG_VIDEO_OV13858                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV2640                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV2659                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV2680                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV2685                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV2740                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_VIDEO_OV5640                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV5645                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV5647                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV5648                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV5670                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV5675                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV5695                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV6650                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV7251                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV7640                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV7670                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV772X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV7740                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV8856                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV8865                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV9282                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV9640                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV9650                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_OV9734                             policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_VIDEO_PCI_SKELETON                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_VIDEO_PVRUSB2                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_PVRUSB2_DEBUGIFC                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_VIDEO_PVRUSB2_DVB                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_PVRUSB2_SYSFS                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_QCOM_CAMSS                         policy<{'arm64': 'm'}>
+CONFIG_VIDEO_QCOM_VENUS                         policy<{'arm64': 'm'}>
+CONFIG_VIDEO_RCAR_CSI2                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RCAR_DRIF                          policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RCAR_VIN                           policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RDACM20                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_RDACM21                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_RENESAS_CEU                        policy<{'armhf': 'm'}>
+CONFIG_VIDEO_RENESAS_FCP                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RENESAS_FDP1                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RENESAS_JPU                        policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RENESAS_VSP1                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_RJ54N1                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ROCKCHIP_ISP1                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_ROCKCHIP_RGA                       policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_ROCKCHIP_VDEC                      policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_S5C73M3                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_S5K4ECGX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_S5K5BAF                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_S5K6A3                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_S5K6AA                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA6588                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA6752HS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7110                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA711X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7127                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7134                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7134_ALSA                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7134_DVB                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7134_GO7007                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7134_RC                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_SAA7146                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7146_VV                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7164                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA717X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAA7185                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS                 policy<{'armhf': 'n'}>
+CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC                 policy<{'armhf': 'm'}>
+CONFIG_VIDEO_SAMSUNG_S5P_G2D                    policy<{'armhf': 'm'}>
+CONFIG_VIDEO_SAMSUNG_S5P_JPEG                   policy<{'armhf': 'm'}>
+CONFIG_VIDEO_SAMSUNG_S5P_MFC                    policy<{'armhf': 'm'}>
+CONFIG_VIDEO_SOLO6X10                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SONY_BTF_MPX                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SR030PC30                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_STK1160                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_STK1160_COMMON                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ST_MIPID02                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_SUN4I_CSI                          policy<{'arm64': 'm'}>
+CONFIG_VIDEO_SUN6I_CSI                          policy<{'arm64': 'm'}>
+CONFIG_VIDEO_SUN8I_DEINTERLACE                  policy<{'arm64': 'm'}>
+CONFIG_VIDEO_SUN8I_ROTATE                       policy<{'arm64': 'm'}>
+CONFIG_VIDEO_SUNXI                              policy<{'arm64': 'y'}>
+CONFIG_VIDEO_SUNXI_CEDRUS                       policy<{'arm64': 'm'}>
+CONFIG_VIDEO_TC358743                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TC358743_CEC                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_TDA1997X                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TDA7432                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TDA9840                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TEA6415C                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TEA6420                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TEGRA                              policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_VIDEO_TEGRA_TPG                          policy<{'arm64': 'y', 'armhf-generic': 'y'}>
+CONFIG_VIDEO_THS7303                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_THS8200                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TI_CAL                             policy<{'arm64': 'm', 'armhf': 'm'}>
+CONFIG_VIDEO_TI_CAL_MC                          policy<{'arm64': 'y', 'armhf-generic': 'n', 'armhf-generic-lpae': 'y'}>
+CONFIG_VIDEO_TI_CSC                             policy<{'armhf': 'm'}>
+CONFIG_VIDEO_TI_SC                              policy<{'armhf': 'm'}>
+CONFIG_VIDEO_TI_VPDMA                           policy<{'armhf': 'm'}>
+CONFIG_VIDEO_TI_VPE                             policy<{'armhf': 'm'}>
+CONFIG_VIDEO_TI_VPE_DEBUG                       policy<{'armhf': 'n'}>
+CONFIG_VIDEO_TLV320AIC23B                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TM6000                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TM6000_ALSA                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TM6000_DVB                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TUNER                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TVAUDIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TVEEPROM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TVP514X                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TVP5150                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TVP7002                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW2804                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW5864                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW68                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW686X                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW9903                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW9906                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_TW9910                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_UDA1342                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_UPD64031A                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_UPD64083                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_USBTV                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_V4L2                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_V4L2_I2C                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_V4L2_SUBDEV_API                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_V4L2_TPG                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VIA_CAMERA                         policy<{'amd64': 'm'}>
+CONFIG_VIDEO_VICODEC                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VIM2M                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VIVID                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VIVID_CEC                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIDEO_VIVID_MAX_DEVS                     policy<{'amd64': '64', 'arm64': '64', 'armhf': '64', 'ppc64el': '64'}>
+CONFIG_VIDEO_VP27SMPX                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VPX3220                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_VS6624                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_WM8739                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_WM8775                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_XILINX                             policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_XILINX_CSI2RXSS                    policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_XILINX_TPG                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_XILINX_VTC                         policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_AVS6EYES                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_BUZ                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_DC10                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_DC30                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_LML33                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_LML33R10                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIDEO_ZORAN_ZR36060                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIPERBOARD_ADC                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIRTIO                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_BALLOON                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_CONSOLE                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_DMA_SHARED_BUFFER                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTIO_FS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTIO_INPUT                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTIO_IOMMU                             policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_VIRTIO_MEM                               policy<{'amd64': 'm'}>
+CONFIG_VIRTIO_MENU                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VIRTIO_PCI                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_PCI_LEGACY                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_PCI_LIB                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRTIO_PMEM                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf-generic-lpae': 'm', 'ppc64el': 'm'}>
+CONFIG_VIRTIO_VDPA                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VIRTIO_VSOCKETS                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTIO_VSOCKETS_COMMON                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VIRTUALIZATION                           policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRT_CPU_ACCOUNTING                      policy<{'s390x': 'y'}>
+CONFIG_VIRT_CPU_ACCOUNTING_GEN                  policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_VIRT_CPU_ACCOUNTING_NATIVE               policy<{'ppc64el': 'n', 's390x': 'y'}>
+CONFIG_VIRT_DRIVERS                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VIRT_TO_BUS                              policy<{'amd64': 'y'}>
+CONFIG_VIRT_WIFI                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VISCONTI_WATCHDOG                        policy<{'arm64': 'm'}>
+CONFIG_VITESSE_PHY                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VL53L0X_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VL6180                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VLAN_8021Q                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VLAN_8021Q_GVRP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VLAN_8021Q_MVRP                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VMAP_PFN                                 policy<{'amd64': 'y'}>
+CONFIG_VMAP_STACK                               policy<{'amd64': 'y', 'arm64': 'y', 's390x': 'y'}>
+CONFIG_VMCP                                     policy<{'s390x': 'y'}>
+CONFIG_VMCP_CMA_SIZE                            policy<{'s390x': '4'}>
+CONFIG_VMD                                      policy<{'amd64': 'm'}>
+CONFIG_VME_BUS                                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_VME_CA91CX42                             policy<{'amd64': 'm'}>
+CONFIG_VME_FAKE                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VME_TSI148                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VME_USER                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VMIVME_7805                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VMLINUX_MAP                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VMLOGRDR                                 policy<{'s390x': 'm'}>
+CONFIG_VMSPLIT_1G                               policy<{'armhf': 'n'}>
+CONFIG_VMSPLIT_2G                               policy<{'armhf': 'n'}>
+CONFIG_VMSPLIT_3G                               policy<{'armhf': 'y'}>
+CONFIG_VMSPLIT_3G_OPT                           policy<{'armhf-generic': 'n'}>
+CONFIG_VMWARE_BALLOON                           policy<{'amd64': 'm'}>
+CONFIG_VMWARE_PVSCSI                            policy<{'amd64': 'm'}>
+CONFIG_VMXNET3                                  policy<{'amd64': 'm', 'arm64-generic': 'm', 'arm64-lowlatency': 'm', 'armhf': 'm', 's390x': 'n'}>
+CONFIG_VM_EVENT_COUNTERS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VORTEX                                   policy<{'amd64': 'm', 'arm64': 'm', 'ppc64el': 'm'}>
+CONFIG_VP_VDPA                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VSOCKETS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VSOCKETS_DIAG                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VSOCKETS_LOOPBACK                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VSOCKMON                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VSX                                      policy<{'ppc64el': 'y'}>
+CONFIG_VT                                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VT6655                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VT6656                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_VT_CONSOLE                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VT_CONSOLE_SLEEP                         policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_VT_HW_CONSOLE_BINDING                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_VXFS_FS                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_VXGE                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_VXGE_DEBUG_TRACE_ALL                     policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_VXLAN                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_VZ89X                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1                                       policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_W1_CON                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_W1_MASTER_DS1WM                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_MASTER_DS2482                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_MASTER_DS2490                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_MASTER_GPIO                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_MASTER_MATROX                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_MASTER_MXC                            policy<{'arm64': 'm', 'armhf-generic': 'm'}>
+CONFIG_W1_MASTER_SGI                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2405                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2406                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2408                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2408_READBACK                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_W1_SLAVE_DS2413                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2423                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2430                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2431                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2433                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2433_CRC                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_W1_SLAVE_DS2438                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS250X                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2780                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2781                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS2805                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS28E04                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_DS28E17                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_SMEM                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W1_SLAVE_THERM                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_W83627HF_WDT                             policy<{'amd64': 'm'}>
+CONFIG_W83877F_WDT                              policy<{'amd64': 'm'}>
+CONFIG_W83977F_WDT                              policy<{'amd64': 'm'}>
+CONFIG_WAFER_WDT                                policy<{'amd64': 'm'}>
+CONFIG_WAN                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_WANT_COMPAT_NETLINK_MESSAGES             policy<{'amd64': 'y'}>
+CONFIG_WANT_DEV_COREDUMP                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WANXL                                    policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WARN_ALL_UNSEEDED_RANDOM                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WATCHDOG                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCHDOG_CORE                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCHDOG_HRTIMER_PRETIMEOUT              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WATCHDOG_NOWAYOUT                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WATCHDOG_OPEN_TIMEOUT                    policy<{'amd64': '0', 'arm64': '0', 'armhf': '0', 'ppc64el': '0', 's390x': '0'}>
+CONFIG_WATCHDOG_PRETIMEOUT_DEFAULT_GOV_NOOP     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC    policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WATCHDOG_PRETIMEOUT_GOV                  policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCHDOG_PRETIMEOUT_GOV_NOOP             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCHDOG_PRETIMEOUT_GOV_PANIC            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_WATCHDOG_PRETIMEOUT_GOV_SEL              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_WATCHDOG_RTAS                            policy<{'ppc64el': 'm'}>
+CONFIG_WATCHDOG_SYSFS                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WATCH_QUEUE                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_WCN36XX                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WCN36XX_DEBUGFS                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_WDAT_WDT                                 policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_WDTPCI                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_WERROR                                   policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WEXT_CORE                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WEXT_PRIV                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WEXT_PROC                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WEXT_SPY                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WFX                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WIL6210                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WIL6210_DEBUGFS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WIL6210_ISR_COR                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WIL6210_TRACING                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WILC1000                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WILC1000_HW_OOB_INTR                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WILC1000_SDIO                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WILC1000_SPI                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WILCO_EC                                 policy<{'amd64': 'm'}>
+CONFIG_WILCO_EC_DEBUGFS                         policy<{'amd64': 'm'}>
+CONFIG_WILCO_EC_EVENTS                          policy<{'amd64': 'm'}>
+CONFIG_WILCO_EC_TELEMETRY                       policy<{'amd64': 'm'}>
+CONFIG_WILINK_PLATFORM_DATA                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WINBOND_840                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WINDFARM                                 policy<{'ppc64el': 'm'}>
+CONFIG_WIREGUARD                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_WIREGUARD_DEBUG                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WIRELESS                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WIRELESS_EXT                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WIRELESS_HOTKEY                          policy<{'amd64': 'm'}>
+CONFIG_WIZNET_BUS_ANY                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WIZNET_BUS_DIRECT                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_WIZNET_BUS_INDIRECT                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_WIZNET_W5100                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WIZNET_W5100_SPI                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WIZNET_W5300                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WKUP_M3_IPC                              policy<{'armhf-generic': 'n'}>
+CONFIG_WKUP_M3_RPROC                            policy<{'armhf-generic': 'm'}>
+CONFIG_WL1251                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WL1251_SDIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WL1251_SPI                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WL12XX                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WL18XX                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WLAN                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_ADMTEK                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_ATH                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_ATMEL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_BROADCOM                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_CISCO                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_INTEL                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_INTERSIL                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_MARVELL                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_MEDIATEK                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_MICROCHIP                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_QUANTENNA                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_RALINK                       policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_REALTEK                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_RSI                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_ST                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_TI                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLAN_VENDOR_ZYDAS                        policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WLCORE                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WLCORE_SDIO                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WLCORE_SPI                               policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WM831X_BACKUP                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WM831X_POWER                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WM831X_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WM8350_POWER                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WM8350_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WMI_BMOF                                 policy<{'amd64': 'm'}>
+CONFIG_WQ_POWER_EFFICIENT_DEFAULT               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_WQ_WATCHDOG                              policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_WWAN_HWSIM                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_WW_MUTEX_SELFTEST                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_X25                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_X86                                      policy<{'amd64': 'y'}>
+CONFIG_X86_16BIT                                policy<{'amd64': 'y'}>
+CONFIG_X86_5LEVEL                               policy<{'amd64': 'y'}>
+CONFIG_X86_64                                   policy<{'amd64': 'y'}>
+CONFIG_X86_64_ACPI_NUMA                         policy<{'amd64': 'y'}>
+CONFIG_X86_64_SMP                               policy<{'amd64': 'y'}>
+CONFIG_X86_ACPI_CPUFREQ_CPB                     policy<{'amd64': 'y'}>
+CONFIG_X86_AMD_FREQ_SENSITIVITY                 policy<{'amd64': 'm'}>
+CONFIG_X86_AMD_PLATFORM_DEVICE                  policy<{'amd64': 'y'}>
+CONFIG_X86_AMD_PSTATE                           policy<{'amd64': 'y'}>
+CONFIG_X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK    policy<{'amd64': 'y'}>
+CONFIG_X86_CHECK_BIOS_CORRUPTION                policy<{'amd64': 'y'}>
+CONFIG_X86_CMOV                                 policy<{'amd64': 'y'}>
+CONFIG_X86_CMPXCHG64                            policy<{'amd64': 'y'}>
+CONFIG_X86_CPA_STATISTICS                       policy<{'amd64': 'n'}>
+CONFIG_X86_CPUID                                policy<{'amd64': 'm'}>
+CONFIG_X86_CPU_RESCTRL                          policy<{'amd64': 'y'}>
+CONFIG_X86_DEBUGCTLMSR                          policy<{'amd64': 'y'}>
+CONFIG_X86_DEBUG_FPU                            policy<{'amd64': 'y'}>
+CONFIG_X86_DECODER_SELFTEST                     policy<{'amd64': 'n'}>
+CONFIG_X86_DIRECT_GBPAGES                       policy<{'amd64': 'y'}>
+CONFIG_X86_ESPFIX64                             policy<{'amd64': 'y'}>
+CONFIG_X86_EXTENDED_PLATFORM                    policy<{'amd64': 'y'}>
+CONFIG_X86_FEATURE_NAMES                        policy<{'amd64': 'y'}>
+CONFIG_X86_GOLDFISH                             policy<{'amd64': 'n'}>
+CONFIG_X86_HV_CALLBACK_VECTOR                   policy<{'amd64': 'y'}>
+CONFIG_X86_INTEL_LPSS                           policy<{'amd64': 'y'}>
+CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS         policy<{'amd64': 'y'}>
+CONFIG_X86_INTEL_MID                            policy<{'amd64': 'n'}>
+CONFIG_X86_INTEL_PSTATE                         policy<{'amd64': 'y'}>
+CONFIG_X86_INTEL_TSX_MODE_AUTO                  policy<{'amd64': 'n'}>
+CONFIG_X86_INTEL_TSX_MODE_OFF                   policy<{'amd64': 'y'}>
+CONFIG_X86_INTEL_TSX_MODE_ON                    policy<{'amd64': 'n'}>
+CONFIG_X86_INTERNODE_CACHE_SHIFT                policy<{'amd64': '6'}>
+CONFIG_X86_IOPL_IOPERM                          policy<{'amd64': 'y'}>
+CONFIG_X86_IO_APIC                              policy<{'amd64': 'y'}>
+CONFIG_X86_L1_CACHE_SHIFT                       policy<{'amd64': '6'}>
+CONFIG_X86_LOCAL_APIC                           policy<{'amd64': 'y'}>
+CONFIG_X86_MCE                                  policy<{'amd64': 'y'}>
+CONFIG_X86_MCELOG_LEGACY                        policy<{'amd64': 'y'}>
+CONFIG_X86_MCE_AMD                              policy<{'amd64': 'y'}>
+CONFIG_X86_MCE_INJECT                           policy<{'amd64': 'm'}>
+CONFIG_X86_MCE_INTEL                            policy<{'amd64': 'y'}>
+CONFIG_X86_MCE_THRESHOLD                        policy<{'amd64': 'y'}>
+CONFIG_X86_MINIMUM_CPU_FAMILY                   policy<{'amd64': '64'}>
+CONFIG_X86_MPPARSE                              policy<{'amd64': 'y'}>
+CONFIG_X86_MSR                                  policy<{'amd64': 'm'}>
+CONFIG_X86_NEED_RELOCS                          policy<{'amd64': 'y'}>
+CONFIG_X86_NUMACHIP                             policy<{'amd64': 'y'}>
+CONFIG_X86_P4_CLOCKMOD                          policy<{'amd64': 'm'}>
+CONFIG_X86_PAT                                  policy<{'amd64': 'y'}>
+CONFIG_X86_PKG_TEMP_THERMAL                     policy<{'amd64': 'm'}>
+CONFIG_X86_PLATFORM_DEVICES                     policy<{'amd64': 'y'}>
+CONFIG_X86_PLATFORM_DRIVERS_DELL                policy<{'amd64': 'y'}>
+CONFIG_X86_PLATFORM_DRIVERS_HP                  policy<{'amd64': 'y'}>
+CONFIG_X86_PMEM_LEGACY                          policy<{'amd64': 'y'}>
+CONFIG_X86_PMEM_LEGACY_DEVICE                   policy<{'amd64': 'y'}>
+CONFIG_X86_PM_TIMER                             policy<{'amd64': 'y'}>
+CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS         policy<{'amd64': 'y'}>
+CONFIG_X86_SGX                                  policy<{'amd64': 'y'}>
+CONFIG_X86_SGX_KVM                              policy<{'amd64': 'y'}>
+CONFIG_X86_SMAP                                 policy<{'amd64': 'y'}>
+CONFIG_X86_SPEEDSTEP_LIB                        policy<{'amd64': 'm'}>
+CONFIG_X86_SUPPORTS_MEMORY_FAILURE              policy<{'amd64': 'y'}>
+CONFIG_X86_THERMAL_VECTOR                       policy<{'amd64': 'y'}>
+CONFIG_X86_TSC                                  policy<{'amd64': 'y'}>
+CONFIG_X86_UMIP                                 policy<{'amd64': 'y'}>
+CONFIG_X86_VERBOSE_BOOTUP                       policy<{'amd64': 'n'}>
+CONFIG_X86_VMX_FEATURE_NAMES                    policy<{'amd64': 'y'}>
+CONFIG_X86_VSMP                                 policy<{'amd64': 'n'}>
+CONFIG_X86_VSYSCALL_EMULATION                   policy<{'amd64': 'y'}>
+CONFIG_X86_X2APIC                               policy<{'amd64': 'y'}>
+CONFIG_X86_X32                                  policy<{'amd64': 'y'}>
+CONFIG_XARRAY_MULTI                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf-generic-lpae': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XDP_SOCKETS                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XDP_SOCKETS_DIAG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XEN                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'n'}>
+CONFIG_XENFS                                    policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_ACPI                                 policy<{'amd64': 'y'}>
+CONFIG_XEN_AUTO_XLATE                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_BACKEND                              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_BALLOON                              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_BALLOON_MEMORY_HOTPLUG               policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_BLKDEV_BACKEND                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_COMPAT_XENFS                         policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_DEBUG_FS                             policy<{'amd64': 'n'}>
+CONFIG_XEN_DEV_EVTCHN                           policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_DOM0                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_EFI                                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_FBDEV_FRONTEND                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_FRONT_PGDIR_SHBUF                    policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_GNTDEV                               policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_GNTDEV_DMABUF                        policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_GRANT_DEV_ALLOC                      policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_GRANT_DMA_ALLOC                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_HAVE_PVMMU                           policy<{'amd64': 'y'}>
+CONFIG_XEN_HAVE_VPMU                            policy<{'amd64': 'y'}>
+CONFIG_XEN_MCE_LOG                              policy<{'amd64': 'y'}>
+CONFIG_XEN_MEMORY_HOTPLUG_LIMIT                 policy<{'amd64': '512'}>
+CONFIG_XEN_NETDEV_BACKEND                       policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_PCIDEV_BACKEND                       policy<{'amd64': 'm'}>
+CONFIG_XEN_PCIDEV_FRONTEND                      policy<{'amd64': 'm'}>
+CONFIG_XEN_PRIVCMD                              policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_PV                                   policy<{'amd64': 'y'}>
+CONFIG_XEN_PVCALLS_BACKEND                      policy<{'amd64': 'n', 'arm64': 'n'}>
+CONFIG_XEN_PVCALLS_FRONTEND                     policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_PVH                                  policy<{'amd64': 'y'}>
+CONFIG_XEN_PVHVM                                policy<{'amd64': 'y'}>
+CONFIG_XEN_PVHVM_GUEST                          policy<{'amd64': 'y'}>
+CONFIG_XEN_PVHVM_SMP                            policy<{'amd64': 'y'}>
+CONFIG_XEN_PV_DOM0                              policy<{'amd64': 'y'}>
+CONFIG_XEN_PV_SMP                               policy<{'amd64': 'y'}>
+CONFIG_XEN_SAVE_RESTORE                         policy<{'amd64': 'y'}>
+CONFIG_XEN_SCRUB_PAGES_DEFAULT                  policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_SCSI_BACKEND                         policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_SCSI_FRONTEND                        policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_SYMS                                 policy<{'amd64': 'y'}>
+CONFIG_XEN_SYS_HYPERVISOR                       policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XEN_UNPOPULATED_ALLOC                    policy<{'amd64': 'y'}>
+CONFIG_XEN_WDT                                  policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_XEN_XENBUS_FRONTEND                      policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_XFRM                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFRM_AH                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFRM_ALGO                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFRM_ESP                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFRM_ESPINTCP                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFRM_INTERFACE                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFRM_IPCOMP                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFRM_MIGRATE                             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_XFRM_OFFLOAD                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFRM_STATISTICS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFRM_SUB_POLICY                          policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_XFRM_USER                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFRM_USER_COMPAT                         policy<{'amd64': 'm'}>
+CONFIG_XFS_DEBUG                                policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_XFS_FS                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XFS_ONLINE_SCRUB                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_XFS_POSIX_ACL                            policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFS_QUOTA                                policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFS_RT                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFS_SUPPORT_V4                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XFS_WARN                                 policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_XGENE_DMA                                policy<{'arm64': 'm'}>
+CONFIG_XGENE_PMU                                policy<{'arm64': 'y'}>
+CONFIG_XGENE_SLIMPRO_MBOX                       policy<{'arm64': 'm'}>
+CONFIG_XIAOMI_WMI                               policy<{'amd64': 'm'}>
+CONFIG_XILINX_AXI_EMAC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XILINX_DMA                               policy<{'arm64': 'm'}>
+CONFIG_XILINX_EMACLITE                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_XILINX_GMII2RGMII                        policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XILINX_INTC                              policy<{'arm64': 'y'}>
+CONFIG_XILINX_LL_TEMAC                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_XILINX_PR_DECOUPLER                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILINX_SDFEC                             policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_XILINX_VCU                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILINX_WATCHDOG                          policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_XILINX_XADC                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILINX_ZYNQMP_DMA                        policy<{'arm64': 'm'}>
+CONFIG_XILINX_ZYNQMP_DPDMA                      policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILLYBUS                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_XILLYBUS_CLASS                           policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILLYBUS_OF                              policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILLYBUS_PCIE                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XILLYUSB                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XIL_AXIS_FIFO                            policy<{'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_XMON                                     policy<{'ppc64el': 'y'}>
+CONFIG_XMON_DEFAULT                             policy<{'ppc64el': 'n'}>
+CONFIG_XMON_DEFAULT_RO_MODE                     policy<{'ppc64el': 'y'}>
+CONFIG_XMON_DISASSEMBLY                         policy<{'ppc64el': 'y'}>
+CONFIG_XOR_BLOCKS                               policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_XPOWER_PMIC_OPREGION                     policy<{'amd64': 'y'}>
+CONFIG_XPS                                      policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XXHASH                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_XZ_DEC_ARM                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_XZ_DEC_ARMTHUMB                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_XZ_DEC_BCJ                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_XZ_DEC_IA64                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_XZ_DEC_POWERPC                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_XZ_DEC_SPARC                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_XZ_DEC_TEST                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_XZ_DEC_X86                               policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'n'}>
+CONFIG_YAM                                      policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_YAMAHA_YAS530                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_YELLOWFIN                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_YENTA                                    policy<{'amd64': 'm', 'arm64': 'm'}>
+CONFIG_YENTA_ENE_TUNE                           policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_YENTA_O2                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_YENTA_RICOH                              policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_YENTA_TI                                 policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_YENTA_TOSHIBA                            policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_Z3FOLD                                   policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ZBOOT_ROM_BSS                            policy<{'armhf': '0x0'}>
+CONFIG_ZBOOT_ROM_TEXT                           policy<{'armhf': '0x0'}>
+CONFIG_ZBUD                                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZCRYPT                                   policy<{'s390x': 'm'}>
+CONFIG_ZCRYPT_DEBUG                             policy<{'s390x': 'n'}>
+CONFIG_ZD1211RW                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ZD1211RW_DEBUG                           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n'}>
+CONFIG_ZEROPLUS_FF                              policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y'}>
+CONFIG_ZERO_CALL_USED_REGS                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZFCP                                     policy<{'s390x': 'm'}>
+CONFIG_ZIIRAVE_WATCHDOG                         policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'n'}>
+CONFIG_ZISOFS                                   policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZLIB_DEFLATE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZLIB_INFLATE                             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZONEFS_FS                                policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ZONE_DEVICE                              policy<{'amd64': 'y', 'arm64': 'y', 'ppc64el': 'y'}>
+CONFIG_ZONE_DMA32                               policy<{'amd64': 'y', 'arm64': 'y'}>
+CONFIG_ZOPT2201                                 policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ZPA2326                                  policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ZPA2326_I2C                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ZPA2326_SPI                              policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm'}>
+CONFIG_ZPOOL                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZRAM                                     policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ZRAM_DEF_COMP                            policy<{'amd64': '"lzo-rle"', 'arm64': '"lzo-rle"', 'armhf': '"lzo-rle"', 'ppc64el': '"lzo-rle"', 's390x': '"lzo-rle"'}>
+CONFIG_ZRAM_DEF_COMP_842                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZRAM_DEF_COMP_LZ4                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZRAM_DEF_COMP_LZ4HC                      policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZRAM_DEF_COMP_LZO                        policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZRAM_DEF_COMP_LZORLE                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZRAM_DEF_COMP_ZSTD                       policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZRAM_MEMORY_TRACKING                     policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZRAM_WRITEBACK                           policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZSMALLOC                                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZSMALLOC_STAT                            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSTD_COMPRESS                            policy<{'amd64': 'm', 'arm64': 'm', 'armhf': 'm', 'ppc64el': 'm', 's390x': 'm'}>
+CONFIG_ZSTD_DECOMPRESS                          policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZSWAP                                    policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT                 policy<{'amd64': '"lzo"', 'arm64': '"lzo"', 'armhf': '"lzo"', 'ppc64el': '"lzo"', 's390x': '"lzo"'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT_842             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT_DEFLATE         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT_LZ4             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT_LZ4HC           policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT_LZO             policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZSWAP_COMPRESSOR_DEFAULT_ZSTD            policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_DEFAULT_ON                         policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_ZPOOL_DEFAULT                      policy<{'amd64': '"zbud"', 'arm64': '"zbud"', 'armhf': '"zbud"', 'ppc64el': '"zbud"', 's390x': '"zbud"'}>
+CONFIG_ZSWAP_ZPOOL_DEFAULT_Z3FOLD               policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZSWAP_ZPOOL_DEFAULT_ZBUD                 policy<{'amd64': 'y', 'arm64': 'y', 'armhf': 'y', 'ppc64el': 'y', 's390x': 'y'}>
+CONFIG_ZSWAP_ZPOOL_DEFAULT_ZSMALLOC             policy<{'amd64': 'n', 'arm64': 'n', 'armhf': 'n', 'ppc64el': 'n', 's390x': 'n'}>
+CONFIG_ZYNQMP_FIRMWARE                          policy<{'arm64': 'y'}>
+CONFIG_ZYNQMP_FIRMWARE_DEBUG                    policy<{'arm64': 'n'}>
+CONFIG_ZYNQMP_IPI_MBOX                          policy<{'arm64': 'y'}>
+CONFIG_ZYNQMP_PM_DOMAINS                        policy<{'arm64': 'y'}>
+CONFIG_ZYNQMP_POWER                             policy<{'arm64': 'y'}>
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/flavour-control.stub
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/flavour-control.stub
@@ -0,0 +1,142 @@
+# Items that get replaced:
+# FLAVOUR
+# DESC
+# ARCH
+# SUPPORTED
+# TARGET
+# BOOTLOADER
+# =PROVIDES=
+#
+# Items marked with =FOO= are optional
+#
+# This file describes the template for packages that are created for each flavour
+# in debian/control.d/vars.*
+#
+# This file gets edited in a couple of places. See the debian/control.stub rule in
+# debian/rules. PGGVER, ABINUM, and SRCPKGNAME are all converted in the
+# process of creating debian/control.
+#
+# The flavour specific strings (ARCH, DESC, etc) are converted using values from the various
+# flavour files in debian/control.d/vars.*
+#
+# XXX: Leave the blank line before the first package!!
+
+Package: linux-image=SIGN-ME-PKG=-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Provides: linux-image, fuse-module, =PROVIDES=${linux:rprovides}
+Depends: ${misc:Depends}, ${shlibs:Depends}, kmod, linux-base (>= 4.5ubuntu1~16.04.1), linux-modules-PKGVER-ABINUM-FLAVOUR
+Recommends: BOOTLOADER, initramfs-tools | linux-initramfs-tool
+Breaks: flash-kernel (<< 3.90ubuntu2) [arm64 armhf], s390-tools (<< 2.3.0-0ubuntu3) [s390x]
+Conflicts: linux-image=SIGN-PEER-PKG=-PKGVER-ABINUM-FLAVOUR
+Suggests: fdutils, linux-doc | SRCPKGNAME-source-PKGVER, SRCPKGNAME-tools, linux-headers-PKGVER-ABINUM-FLAVOUR, linux-modules-extra-PKGVER-ABINUM-FLAVOUR
+Description: Linux kernel image for version PKGVER on DESC
+ This package contains the=SIGN-ME-TXT= Linux kernel image for version PKGVER on
+ DESC.
+ .
+ Supports SUPPORTED processors.
+ .
+ TARGET
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-FLAVOUR meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-modules-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-image-PKGVER-ABINUM-FLAVOUR | linux-image-unsigned-PKGVER-ABINUM-FLAVOUR
+Built-Using: ${linux:BuiltUsing}
+Description: Linux kernel extra modules for version PKGVER on DESC
+ Contains the corresponding System.map file, the modules built by the
+ packager, and scripts that try to ensure that the system is not left in an
+ unbootable state after an update.
+ .
+ Supports SUPPORTED processors.
+ .
+ TARGET
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-FLAVOUR meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-modules-extra-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-image-PKGVER-ABINUM-FLAVOUR | linux-image-unsigned-PKGVER-ABINUM-FLAVOUR, wireless-regdb
+Description: Linux kernel extra modules for version PKGVER on DESC
+ This package contains the Linux kernel extra modules for version PKGVER on
+ DESC.
+ .
+ Also includes the corresponding System.map file, the modules built by the
+ packager, and scripts that try to ensure that the system is not left in an
+ unbootable state after an update.
+ .
+ Supports SUPPORTED processors.
+ .
+ TARGET
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-FLAVOUR meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-headers-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, SRCPKGNAME-headers-PKGVER-ABINUM, ${shlibs:Depends}
+Provides: linux-headers, linux-headers-3.0
+Description: Linux kernel headers for version PKGVER on DESC
+ This package provides kernel header files for version PKGVER on
+ DESC.
+ .
+ This is for sites that want the latest kernel headers.  Please read
+ /usr/share/doc/linux-headers-PKGVER-ABINUM/debian.README.gz for details.
+
+Package: linux-image=SIGN-ME-PKG=-PKGVER-ABINUM-FLAVOUR-dbgsym
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}
+Provides: linux-debug
+Description: Linux kernel debug image for version PKGVER on DESC
+ This package provides the=SIGN-ME-TXT= kernel debug image for version PKGVER on
+ DESC.
+ .
+ This is for sites that wish to debug the kernel.
+ .
+ The kernel image contained in this package is NOT meant to boot from. It
+ is uncompressed, and unstripped. This package also includes the
+ unstripped modules.
+
+Package: linux-tools-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, SRCPKGNAME-tools-PKGVER-ABINUM
+Description: Linux kernel version specific tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version PKGVER-ABINUM on
+ =HUMAN=.
+
+Package: linux-cloud-tools-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, SRCPKGNAME-cloud-tools-PKGVER-ABINUM
+Description: Linux kernel version specific cloud tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools for cloud for version PKGVER-ABINUM on
+ =HUMAN=.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/generic.inclusion-list
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/generic.inclusion-list
@@ -0,0 +1,306 @@
+arch/*/{crypto,kernel,oprofile}
+arch/*/kvm/kvm.ko
+arch/powerpc/kvm/kvm-hv.ko
+arch/powerpc/kvm/kvm-pr.ko
+arch/powerpc/kvm/vfio.ko
+arch/powerpc/platforms/powernv/opal-prd.ko
+arch/s390/*
+arch/x86/kvm/kvm-amd.ko
+arch/x86/kvm/kvm-intel.ko
+crypto/*
+drivers/acpi/*
+drivers/ata/acard-ahci.ko
+drivers/ata/ahci.ko
+drivers/ata/ahci_platform.ko
+drivers/ata/ahci_tegra.ko
+drivers/ata/ata_generic.ko
+drivers/ata/libahci.ko
+drivers/ata/libahci_platform.ko
+drivers/block/brd.ko
+drivers/block/cryptoloop.ko
+drivers/block/floppy.ko
+drivers/block/loop.ko
+drivers/block/nbd.ko
+drivers/block/rbd.ko
+drivers/block/virtio_blk.ko
+drivers/block/xen-blkfront.ko
+drivers/bus/tegra-aconnect.ko
+drivers/char/hangcheck-timer.ko
+drivers/char/hw_random/powernv-rng.ko
+drivers/char/hw_random/virtio-rng.ko
+drivers/char/ipmi/*
+drivers/char/ipmi/ipmi_msghandler.ko
+drivers/char/lp.ko
+drivers/char/nvram.ko
+drivers/char/ppdev.ko
+drivers/char/raw.ko
+drivers/char/virtio_console.ko
+drivers/clk/clk-max77686.ko
+drivers/cpufreq/tegra186-cpufreq.ko
+drivers/cpufreq/tegra194-cpufreq.ko
+drivers/crypto/nx/*
+drivers/crypto/vmx/vmx-crypto.ko
+drivers/dma/tegra210-adma.ko
+drivers/firmware/dmi-sysfs.ko
+drivers/firmware/efi/*
+drivers/firmware/iscsi_ibft.ko
+drivers/gpio/gpio-max77620.ko
+drivers/gpu/drm/ast/ast.ko
+drivers/gpu/drm/bochs/bochs-drm.ko
+drivers/gpu/drm/cirrus/cirrus.ko
+drivers/gpu/drm/drm.ko
+drivers/gpu/drm/drm_kms_helper.ko
+drivers/gpu/drm/tegra/tegra-drm.ko
+drivers/gpu/drm/ttm/ttm.ko
+drivers/gpu/drm/vboxvideo/vboxvideo.ko
+drivers/gpu/drm/virtio/virtio-gpu.ko
+drivers/gpu/drm/vmwgfx/vmwgfx.ko
+drivers/gpu/drm/xen/drm_xen_front.ko
+drivers/gpu/host1x/host1x.ko
+drivers/hid/hid-generic.ko
+drivers/hid/hid-hyperv.ko
+drivers/hid/hid.ko
+drivers/hid/usbhid/usbhid.ko
+drivers/hv/*
+drivers/hwmon/ibmpowernv.ko
+drivers/hwmon/pwm-fan.ko
+drivers/i2c/busses/i2c-tegra-bpmp.ko
+drivers/i2c/busses/i2c-tegra-bpmp.ko
+drivers/i2c/busses/i2c-tegra.ko
+drivers/infiniband/core/ib_addr.ko
+drivers/infiniband/core/ib_cm.ko
+drivers/infiniband/core/ib_core.ko
+drivers/infiniband/core/ib_mad.ko
+drivers/infiniband/core/ib_sa.ko
+drivers/infiniband/core/iw_cm.ko
+drivers/infiniband/core/rdma_cm.ko
+drivers/infiniband/ulp/iser/ib_iser.ko
+drivers/infiniband/ulp/isert/ib_isert.ko
+drivers/input/evbug.ko
+drivers/input/gameport/gameport.ko
+drivers/input/input-leds.ko
+drivers/input/joydev.ko
+drivers/input/keyboard/gpio_keys.ko
+drivers/input/misc/xen-kbdfront.ko
+drivers/input/mouse/psmouse.ko
+drivers/input/serio/hyperv-keyboard.ko
+drivers/input/serio/serio_raw.ko
+drivers/input/serio/serport.ko
+drivers/input/touchscreen/usbtouchscreen.ko
+drivers/leds/leds-powernv.ko
+drivers/md/*
+drivers/memory/tegra/tegra210-emc.ko
+drivers/message/fusion*
+drivers/misc/cxl/*
+drivers/misc/eeprom/at24.ko
+drivers/misc/vmw_balloon.ko
+drivers/misc/vmw_vmci/vmw_vmci.ko
+drivers/mmc/host/sdhci-tegra.ko
+drivers/mtd/cmdlinepart.ko
+drivers/mtd/devices/powernv_flash.ko
+drivers/mtd/ofpart.ko
+drivers/net/appletalk/ipddp.ko
+drivers/net/bonding/bonding.ko
+drivers/net/caif/caif_virtio.ko
+drivers/net/dummy.ko
+drivers/net/eql.ko
+drivers/net/ethernet/8390/8390.ko
+drivers/net/ethernet/8390/ne2k-pci.ko
+drivers/net/ethernet/amazon/ena/ena.ko
+drivers/net/ethernet/amd/pcnet32.ko
+drivers/net/ethernet/broadcom/bnx2x/*
+drivers/net/ethernet/broadcom/tg3.ko
+drivers/net/ethernet/dec/tulip/*
+drivers/net/ethernet/emulex/benet/*
+drivers/net/ethernet/ibm/*
+drivers/net/ethernet/intel/e1000/e1000.ko
+drivers/net/ethernet/intel/e1000e/e1000e.ko
+drivers/net/ethernet/intel/i40e/*
+drivers/net/ethernet/intel/iavf/iavf.ko
+drivers/net/ethernet/intel/igb/*
+drivers/net/ethernet/intel/igbvf/igbvf.ko
+drivers/net/ethernet/intel/ixgbe/*
+drivers/net/ethernet/intel/ixgbevf/ixgbevf.ko
+drivers/net/ethernet/mellanox/*
+drivers/net/ethernet/netronome/nfp/nfp.ko
+drivers/net/ethernet/realtek/8139cp.ko
+drivers/net/ethernet/realtek/8139too.ko
+drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.ko
+drivers/net/ethernet/stmicro/stmmac/stmmac-platform.ko
+drivers/net/ethernet/stmicro/stmmac/stmmac.ko
+drivers/net/fddi/*
+drivers/net/geneve.ko
+drivers/net/hyperv/hv_netvsc.ko
+drivers/net/ifb.ko
+drivers/net/ipvlan/*
+drivers/net/macvlan.ko
+drivers/net/macvtap.ko
+drivers/net/mii.ko
+drivers/net/netconsole.ko
+drivers/net/pcs/pcs-xpcs.ko
+drivers/net/phy/marvell.ko
+drivers/net/phy/phylink.ko
+drivers/net/ppp/*
+drivers/net/ppp/bsd_comp.ko
+drivers/net/slip/*
+drivers/net/veth.ko
+drivers/net/virtio_net.ko
+drivers/net/vmxnet3/vmxnet3.ko
+drivers/net/vxlan.ko
+drivers/net/wireguard/wireguard.ko
+drivers/net/wwan/*
+drivers/net/xen-netback/*
+drivers/net/xen-netfront.ko
+drivers/nvme/host/nvme.ko
+drivers/nvmem/nvmem_core.ko
+drivers/parport/parport.ko
+drivers/parport/parport_pc.ko
+drivers/pci/controller/dwc/pcie-tegra194.ko
+drivers/pci/host/vmd.ko
+drivers/phy/tegra/phy-tegra194-p2u.ko
+drivers/pinctrl/pinctrl-max77620.ko
+drivers/platform/x86/pvpanic.ko
+drivers/pps/pps_core.ko
+drivers/ptp/ptp.ko
+drivers/pwm/pwm-tegra.ko
+drivers/regulator/fixed.ko
+drivers/regulator/max77620-regulator.ko
+drivers/rtc/rtc-max77686.ko
+drivers/rtc/rtc-tegra.ko
+drivers/s390/*
+drivers/s390/block/xpram.ko
+drivers/scsi/BusLogic.ko
+drivers/scsi/aacraid/*
+drivers/scsi/cxlflash/*
+drivers/scsi/device_handler/scsi_dh_alua.ko
+drivers/scsi/device_handler/scsi_dh_emc.ko
+drivers/scsi/device_handler/scsi_dh_hp_sw.ko
+drivers/scsi/device_handler/scsi_dh_rdac.ko
+drivers/scsi/hv_storvsc.ko
+drivers/scsi/ibmvscsi/*
+drivers/scsi/ipr.ko
+drivers/scsi/iscsi_boot_sysfs.ko
+drivers/scsi/iscsi_tcp.ko
+drivers/scsi/libiscsi.ko
+drivers/scsi/libiscsi_tcp.ko
+drivers/scsi/libsas/*
+drivers/scsi/lpfc/*
+drivers/scsi/megaraid/*
+drivers/scsi/mpt3sas/*
+drivers/scsi/osd/libosd.ko
+drivers/scsi/osd/osd.ko
+drivers/scsi/qla1280.ko
+drivers/scsi/qla2xxx/*
+drivers/scsi/raid_class.ko
+drivers/scsi/scsi_transport_fc.ko
+drivers/scsi/scsi_transport_iscsi.ko
+drivers/scsi/scsi_transport_sas.ko
+drivers/scsi/scsi_transport_spi.ko
+drivers/scsi/sd_mod.ko
+drivers/scsi/sr_mod.ko
+drivers/scsi/virtio_scsi.ko
+drivers/scsi/vmw_pvscsi.ko
+drivers/spi/spi-tegra114.ko
+drivers/staging/media/tegra-video/tegra-video.ko
+drivers/target/loopback/tcm_loop.ko
+drivers/target/target_core*.ko
+drivers/thermal/tegra/tegra-bpmp-thermal.ko
+drivers/tty/serial/jsm/*
+drivers/tty/serial/serial-tegra.ko
+drivers/uio/uio.ko
+drivers/uio/uio_pdrv_genirq.ko
+drivers/usb/gadget/udc/tegra-xudc.ko
+drivers/usb/host/*
+drivers/usb/storage/uas.ko
+drivers/usb/storage/usb-storage.ko
+drivers/vfio/*
+drivers/vhost/*
+drivers/video/fbdev/*
+drivers/video/vgastate.ko
+drivers/virt/vboxguest/vboxguest.ko
+drivers/virtio/*
+drivers/watchdog/softdog.ko
+drivers/xen/*
+fs/9p/*
+fs/aufs/aufs.ko
+fs/autofs/autofs4.ko
+fs/binfmt_misc.ko
+fs/btrfs/*
+fs/cachefiles/cachefiles.ko
+fs/ceph/*
+fs/cifs/*
+fs/configfs/*
+fs/dlm/dlm.ko
+fs/ecryptfs/*
+fs/efivarfs/*
+fs/erofs/*
+fs/exofs/libore.ko
+fs/ext4/*
+fs/fat/*
+fs/fscache/*
+fs/fuse/*
+fs/isofs/*
+fs/lockd/*
+fs/nfs/*
+fs/nfs_common/*
+fs/nfsd/*
+fs/nls/nls_cp437.ko
+fs/nls/nls_iso8859-1.ko
+fs/overlayfs/*
+fs/shiftfs.ko
+fs/squashfs/*
+fs/udf/*
+fs/ufs/*
+fs/vboxsf/vboxsf.ko
+fs/xfs/*
+lib/*
+net/6lowpan/*
+net/802/*
+net/8021q/*
+net/9p/*
+net/appletalk/*
+net/atm/*
+net/ax25/*
+net/bpfilter/*
+net/bridge/*
+net/can/*
+net/ceph/libceph.ko
+net/core/*
+net/dccp/*
+net/decnet/*
+net/ieee802154/*
+net/ipv4/*
+net/ipv6/*
+net/ipx/*
+net/key/*
+net/lapb/*
+net/llc/*
+net/netfilter/*
+net/netlink/netlink_diag.ko
+net/netrom/*
+net/openvswitch/*
+net/packet/af_packet_diag.ko
+net/phonet/*
+net/rose/*
+net/rxrpc/*
+net/sched/*
+net/sctp/*
+net/sunrpc/auth_gss/auth_rpcgss.ko
+net/sunrpc/auth_gss/rpcsec_gss_krb5.ko
+net/sunrpc/sunrpc.ko
+net/tipc/*
+net/unix/unix_diag.ko
+net/vmw_vsock/*
+net/x25/*
+net/xfrm/*
+! find sound/core -name oss -prune -o -name *.ko -print
+sound/drivers/pcsp/snd-pcsp.ko
+sound/pci/hda/snd-hda-tegra.ko
+sound/pci/snd-ens1370.ko
+sound/soc/tegra/snd-soc-tegra186-dspk.ko
+sound/soc/tegra/snd-soc-tegra210-admaif.ko
+sound/soc/tegra/snd-soc-tegra210-ahub.ko
+sound/soc/tegra/snd-soc-tegra210-dmic.ko
+sound/soc/tegra/snd-soc-tegra210-i2s.ko
+sound/soundcore.ko
+ubuntu/ubuntu-host/ubuntu-host.ko
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/linux-doc.stub
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/linux-doc.stub
@@ -0,0 +1,12 @@
+Package: linux-doc
+Build-Profiles: <!stage1>
+Architecture: all
+Section: doc
+Priority: optional
+Depends: ${misc:Depends}
+Description: Linux kernel specific documentation for version PKGVER
+ This package provides the various documents in the PKGVER kernel
+ Documentation/ subdirectory.  These document kernel subsystems, APIs, device
+ drivers, and so on.  See
+ /usr/share/doc/SRCPKGNAME-doc/00-INDEX for a list of what is
+ contained in each file.
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/linux-libc-dev.stub
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/linux-libc-dev.stub
@@ -0,0 +1,12 @@
+Package: linux-libc-dev
+Architecture: amd64 armhf arm64 i386 ppc64el riscv64 s390x
+Depends: ${misc:Depends}
+Conflicts: linux-kernel-headers
+Replaces: linux-kernel-headers
+Provides: linux-kernel-headers, aufs-dev
+Multi-Arch: same
+Description: Linux Kernel Headers for development
+ This package provides headers from the Linux kernel.  These headers
+ are used by the installed headers for GNU glibc and other system
+ libraries. They are NOT meant to be used to build third-party modules for
+ your kernel. Use SRCPKGNAME-headers-* packages for that.
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/vars.generic
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/vars.generic
@@ -0,0 +1,6 @@
+arch="amd64 armhf arm64 ppc64el s390x"
+supported="Generic"
+target="Geared toward desktop and server systems."
+desc="=HUMAN= SMP"
+bootloader="grub-pc [amd64] | grub-efi-amd64 [amd64] | grub-efi-ia32 [amd64] | grub [amd64] | lilo [amd64] | flash-kernel [armhf arm64] | grub-efi-arm64 [arm64] | grub-efi-arm [armhf] | grub-ieee1275 [ppc64el]"
+provides="kvm-api-4, redhat-cluster-modules, ivtv-modules, virtualbox-guest-modules [amd64]"
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/vars.generic-64k
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/vars.generic-64k
@@ -0,0 +1,6 @@
+arch="arm64"
+supported="Generic 64K pages"
+target="Geared toward desktop and server systems."
+desc="=HUMAN= SMP"
+bootloader="grub-efi-arm64 [arm64] | flash-kernel [arm64]"
+provides="kvm-api-4, redhat-cluster-modules, ivtv-modules"
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.d/vars.generic-lpae
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.d/vars.generic-lpae
@@ -0,0 +1,6 @@
+arch="armhf"
+supported="Generic LPAE"
+target="Geared toward desktop and server systems."
+desc="=HUMAN= SMP"
+bootloader="flash-kernel [armhf] | grub-efi-arm [armhf]"
+provides="kvm-api-4, redhat-cluster-modules, ivtv-modules"
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/control.stub.in
+++ linux-xilinx-zynqmp-5.15.0/debian.master/control.stub.in
@@ -0,0 +1,157 @@
+Source: SRCPKGNAME
+Section: devel
+Priority: optional
+Maintainer: Ubuntu Kernel Team <kernel-team@lists.ubuntu.com>
+Standards-Version: 3.9.4.0
+Build-Depends:
+ autoconf <!stage1>,
+ automake <!stage1>,
+ bc <!stage1>,
+ bison <!stage1>,
+ cpio,
+ curl <!stage1>,
+ debhelper-compat (= 10),
+ default-jdk-headless <!stage1>,
+ dkms <!stage1>,
+ dwarfdump <!stage1>,
+ flex <!stage1>,
+ gawk <!stage1>,
+ java-common <!stage1>,
+ kmod <!stage1>,
+ libaudit-dev <!stage1>,
+ libcap-dev <!stage1>,
+ libdw-dev <!stage1>,
+ libelf-dev <!stage1>,
+ libiberty-dev <!stage1>,
+ liblzma-dev <!stage1>,
+ libnewt-dev <!stage1>,
+ libnuma-dev [amd64 arm64 ppc64el s390x] <!stage1>,
+ libpci-dev <!stage1>,
+ libssl-dev <!stage1>,
+ libtool <!stage1>,
+ libudev-dev <!stage1>,
+ libunwind8-dev [amd64 arm64 armhf ppc64el] <!stage1>,
+ makedumpfile [amd64] <!stage1>,
+ openssl <!stage1>,
+ pahole [amd64 arm64 armhf ppc64el s390x riscv64] | dwarves (>= 1.21) [amd64 arm64 armhf ppc64el s390x riscv64] <!stage1>,
+ pkg-config <!stage1>,
+ python3-dev <!stage1>,
+ rsync <!stage1>,
+ uuid-dev <!stage1>,
+ zstd [amd64 s390x] <!stage1>,
+Build-Depends-Indep:
+ asciidoc <!stage1>,
+ bzip2 <!stage1>,
+ docbook-utils <!stage1>,
+ dvipng <!stage1>,
+ fig2dev <!stage1>,
+ fontconfig <!stage1>,
+ fonts-noto-cjk <!stage1>,
+ ghostscript <!stage1>,
+ graphviz <!stage1>,
+ imagemagick <!stage1>,
+ latexmk <!stage1>,
+ librsvg2-bin <!stage1>,
+ python3-docutils <!stage1>,
+ python3-sphinx <!stage1>,
+ python3-sphinx-rtd-theme <!stage1>,
+ sharutils <!stage1>,
+ xmlto <!stage1>,
+Vcs-Git: git://git.launchpad.net/~ubuntu-kernel/ubuntu/+source/linux/+git/=SERIES=
+XS-Testsuite: autopkgtest
+#XS-Testsuite-Depends: gcc-4.7 binutils
+
+Package: linux-source-PKGVER
+Build-Profiles: <!stage1>
+Architecture: all
+Section: devel
+Priority: optional
+Provides: linux-source
+Depends: ${misc:Depends}, binutils, bzip2, coreutils
+Recommends: libc-dev, gcc, make
+Suggests: libncurses-dev | ncurses-dev, kernel-package, libqt3-dev
+Description: Linux kernel source for version PKGVER with Ubuntu patches
+ This package provides the source code for the Linux kernel version
+ PKGVER.
+ .
+ This package is mainly meant for other packages to use, in order to build
+ custom flavours.
+ .
+ If you wish to use this package to create a custom Linux kernel, then it
+ is suggested that you investigate the package kernel-package, which has
+ been designed to ease the task of creating kernel image packages.
+ .
+ If you are simply trying to build third-party modules for your kernel,
+ you do not want this package. Install the appropriate linux-headers
+ package instead.
+
+Package: SRCPKGNAME-headers-PKGVER-ABINUM
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, coreutils
+Description: Header files related to Linux kernel version PKGVER
+ This package provides kernel header files for version PKGVER, for sites
+ that want the latest kernel headers. Please read
+ /usr/share/doc/SRCPKGNAME-headers-PKGVER-ABINUM/debian.README.gz for details
+
+Package: SRCPKGNAME-tools-common
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, lsb-release, hwdata
+Description: Linux kernel version specific tools for version PKGVER
+ This package provides the architecture independent parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version PKGVER.
+
+Package: SRCPKGNAME-tools-PKGVER-ABINUM
+Build-Profiles: <!stage1>
+Architecture: amd64 armhf arm64 ppc64el s390x
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-tools-common
+Description: Linux kernel version specific tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version PKGVER-ABINUM on
+ =HUMAN=.
+ You probably want to install linux-tools-PKGVER-ABINUM-<flavour>.
+
+Package: SRCPKGNAME-cloud-tools-common
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}
+Description: Linux kernel version specific cloud tools for version PKGVER
+ This package provides the architecture independent parts for kernel
+ version locked tools for cloud tools for version PKGVER.
+
+Package: SRCPKGNAME-cloud-tools-PKGVER-ABINUM
+Build-Profiles: <!stage1>
+Architecture: amd64 armhf
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-cloud-tools-common
+Description: Linux kernel version specific cloud tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools for cloud tools for version PKGVER-ABINUM on
+ =HUMAN=.
+ You probably want to install linux-cloud-tools-PKGVER-ABINUM-<flavour>.
+
+Package: SRCPKGNAME-tools-host
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, python3
+Description: Linux kernel VM host tools
+ This package provides kernel tools useful for VM hosts.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/copyright
+++ linux-xilinx-zynqmp-5.15.0/debian.master/copyright
@@ -0,0 +1,29 @@
+This is the Ubuntu prepackaged version of the Linux kernel.
+Linux was written by Linus Torvalds <Linus.Torvalds@cs.Helsinki.FI>
+and others.
+
+This package was put together by the Ubuntu Kernel Team, from
+sources retrieved from upstream linux git.
+The sources may be found at most Linux ftp sites, including 
+ftp://ftp.kernel.org/pub/linux/kernel/
+
+This package is currently maintained by the
+Ubuntu Kernel Team <ubuntu-kernel@lists.ubuntu.com>
+
+Linux is copyrighted by Linus Torvalds and others.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; version 2 dated June, 1991.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program; if not, write to the Free Software
+   Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+On Ubuntu Linux systems, the complete text of the GNU General
+Public License v2 can be found in `/usr/share/common-licenses/GPL-2'.
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/dkms-versions
+++ linux-xilinx-zynqmp-5.15.0/debian.master/dkms-versions
@@ -0,0 +1,3 @@
+zfs-linux 2.1.5-1ubuntu6~22.04.5 modulename=zfs debpath=pool/universe/z/%package%/zfs-dkms_%version%_all.deb arch=amd64 arch=arm64 arch=ppc64el arch=s390x rprovides=spl-modules rprovides=spl-dkms rprovides=zfs-modules rprovides=zfs-dkms
+backport-iwlwifi-dkms 11510-0ubuntu1~22.04.3 modulename=iwlwifi debpath=pool/universe/b/%package%/backport-iwlwifi-dkms_%version%_all.deb arch=amd64 rprovides=iwlwifi-modules rprovides=backport-iwlwifi-dkms type=standalone
+v4l2loopback 0.12.7-2ubuntu2~22.04.1 modulename=v4l2loopback debpath=pool/universe/v/%package%/v4l2loopback-dkms_%version%_all.deb arch=amd64 rprovides=v4l2loopback-modules rprovides=v4l2loopback-dkms
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/etc/kernelconfig
+++ linux-xilinx-zynqmp-5.15.0/debian.master/etc/kernelconfig
@@ -0,0 +1,2 @@
+archs="amd64 armhf arm64 ppc64el s390x"
+family='ubuntu'
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/modprobe.d/common.conf
+++ linux-xilinx-zynqmp-5.15.0/debian.master/modprobe.d/common.conf
@@ -0,0 +1,3 @@
+# LP:1434842 -- disable OSS drivers by default to allow pulseaudio to emulate
+blacklist snd-mixer-oss
+blacklist snd-pcm-oss
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/reconstruct
+++ linux-xilinx-zynqmp-5.15.0/debian.master/reconstruct
@@ -0,0 +1,188 @@
+# Recreate any symlinks created since the orig.
+chmod +x 'arch/mips/pci/pcie-octeon.c'
+chmod +x 'arch/s390/tools/gcc-thunk-extern.sh'
+chmod +x 'debian/cloud-tools/hv_get_dhcp_info'
+chmod +x 'debian/cloud-tools/hv_get_dns_info'
+chmod +x 'debian/cloud-tools/hv_set_ifconfig'
+chmod +x 'debian/rules'
+chmod +x 'debian/scripts/config-check'
+chmod +x 'debian/scripts/control-create'
+chmod +x 'debian/scripts/dkms-build'
+chmod +x 'debian/scripts/dkms-build--nvidia-N'
+chmod +x 'debian/scripts/dkms-build-configure--zfs'
+chmod +x 'debian/scripts/file-downloader'
+chmod +x 'debian/scripts/link-headers'
+chmod +x 'debian/scripts/misc/annotations'
+chmod +x 'debian/scripts/misc/arch-has-odm-enabled.sh'
+chmod +x 'debian/scripts/misc/final-checks'
+chmod +x 'debian/scripts/misc/find-missing-sauce.sh'
+chmod +x 'debian/scripts/misc/fw-to-ihex.sh'
+chmod +x 'debian/scripts/misc/gen-auto-reconstruct'
+chmod +x 'debian/scripts/misc/git-ubuntu-log'
+chmod +x 'debian/scripts/misc/insert-changes'
+chmod +x 'debian/scripts/misc/insert-mainline-changes'
+chmod +x 'debian/scripts/misc/insert-ubuntu-changes'
+chmod +x 'debian/scripts/misc/kernelconfig'
+chmod +x 'debian/scripts/misc/migrate-annotations'
+chmod +x 'debian/scripts/misc/retag'
+chmod +x 'debian/scripts/misc/splitconfig.pl'
+chmod +x 'debian/scripts/misc/tristate.sh'
+chmod +x 'debian/scripts/misc/update-aufs.sh'
+chmod +x 'debian/scripts/module-inclusion'
+chmod +x 'debian/scripts/module-signature-check'
+chmod +x 'debian/scripts/retpoline-extract'
+chmod +x 'debian/scripts/retpoline-extract-one'
+chmod +x 'debian/scripts/sign-module'
+chmod +x 'debian/templates/extra.postinst.in'
+chmod +x 'debian/templates/extra.postrm.in'
+chmod +x 'debian/templates/headers.postinst.in'
+chmod +x 'debian/templates/image.postinst.in'
+chmod +x 'debian/templates/image.postrm.in'
+chmod +x 'debian/templates/image.preinst.in'
+chmod +x 'debian/templates/image.prerm.in'
+chmod +x 'debian/tests-build/check-aliases'
+chmod +x 'debian/tests/rebuild'
+chmod +x 'debian/tests/ubuntu-regression-suite'
+chmod +x 'drivers/watchdog/f71808e_wdt.c'
+chmod +x 'scripts/pahole-flags.sh'
+chmod +x 'scripts/pahole-version.sh'
+chmod +x 'tools/testing/selftests/net/fib_nexthop_nongw.sh'
+chmod -x 'tools/testing/selftests/net/setup_loopback.sh'
+chmod +x 'tools/testing/selftests/netfilter/conntrack_vrf.sh'
+# Remove any files deleted from the orig.
+rm -f 'Documentation/devicetree/bindings/ata/ahci-ceva.txt'
+rm -f 'Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml'
+rm -f 'Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml'
+rm -f 'Documentation/networking/decnet.rst'
+rm -f 'Documentation/virt/kvm/amd-memory-encryption.rst'
+rm -f 'Documentation/virt/kvm/cpuid.rst'
+rm -f 'Documentation/virt/kvm/halt-polling.rst'
+rm -f 'Documentation/virt/kvm/hypercalls.rst'
+rm -f 'Documentation/virt/kvm/mmu.rst'
+rm -f 'Documentation/virt/kvm/msr.rst'
+rm -f 'Documentation/virt/kvm/nested-vmx.rst'
+rm -f 'Documentation/virt/kvm/running-nested-guests.rst'
+rm -f 'Documentation/virt/kvm/s390-diag.rst'
+rm -f 'Documentation/virt/kvm/s390-pv-boot.rst'
+rm -f 'Documentation/virt/kvm/s390-pv.rst'
+rm -f 'Documentation/virt/kvm/timekeeping.rst'
+rm -f 'arch/alpha/include/asm/bugs.h'
+rm -f 'arch/arm/mach-pxa/include/mach/spitz.h'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/Makefile'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi'
+rm -f 'arch/hexagon/include/asm/timer-regs.h'
+rm -f 'arch/ia64/include/asm/bugs.h'
+rm -f 'arch/m68k/include/asm/bugs.h'
+rm -f 'arch/parisc/include/asm/bugs.h'
+rm -f 'arch/powerpc/include/asm/bugs.h'
+rm -f 'arch/powerpc/include/uapi/asm/bpf_perf_event.h'
+rm -f 'arch/sh/include/asm/bugs.h'
+rm -f 'arch/sparc/include/asm/bugs.h'
+rm -f 'arch/um/include/asm/bugs.h'
+rm -f 'arch/x86/mm/mem_encrypt.c'
+rm -f 'arch/xtensa/include/asm/bugs.h'
+rm -f 'crypto/blake2s_generic.c'
+rm -f 'crypto/memneq.c'
+rm -f 'drivers/acpi/fan.c'
+rm -f 'drivers/block/sx8.c'
+rm -f 'drivers/bus/mhi/core/Makefile'
+rm -f 'drivers/bus/mhi/core/boot.c'
+rm -f 'drivers/bus/mhi/core/debugfs.c'
+rm -f 'drivers/bus/mhi/core/init.c'
+rm -f 'drivers/bus/mhi/core/internal.h'
+rm -f 'drivers/bus/mhi/core/main.c'
+rm -f 'drivers/bus/mhi/core/pm.c'
+rm -f 'drivers/bus/mhi/pci_generic.c'
+rm -f 'drivers/counter/counter.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/Makefile'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/bw_fixed.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/calcs_logger.h'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/custom_float.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calc_auto.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calc_auto.h'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calc_math.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calcs.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/dml/dcn2x/dcn2x.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/dml/dcn2x/dcn2x.h'
+rm -f 'drivers/gpu/drm/amd/display/dc/dsc/qp_tables.h'
+rm -f 'drivers/gpu/drm/msm/hdmi/hdmi_connector.c'
+rm -f 'drivers/gpu/drm/vmwgfx/vmwgfx_thp.c'
+rm -f 'drivers/iio/adc/stx104.c'
+rm -f 'drivers/infiniband/hw/irdma/status.h'
+rm -f 'drivers/input/serio/i8042-x86ia64io.h'
+rm -f 'drivers/net/ethernet/hisilicon/hns3/hns3pf/Makefile'
+rm -f 'drivers/net/ethernet/hisilicon/hns3/hns3vf/Makefile'
+rm -f 'drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_gpio.c'
+rm -f 'drivers/net/vxlan.c'
+rm -f 'drivers/of/of_net.c'
+rm -f 'drivers/pinctrl/ralink/pinctrl-rt2880.c'
+rm -f 'drivers/pinctrl/ralink/pinmux.h'
+rm -f 'drivers/platform/x86/hp-wmi.c'
+rm -f 'drivers/platform/x86/hp_accel.c'
+rm -f 'drivers/platform/x86/i2c-multi-instantiate.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_clk_and_regulator.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_common.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_common.h'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_discrete.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_tps68470.c'
+rm -f 'drivers/platform/x86/tc1100-wmi.c'
+rm -f 'drivers/staging/most/dim2/sysfs.c'
+rm -f 'drivers/usb/typec/tcpm/tcpci.h'
+rm -f 'fs/io-wq.c'
+rm -f 'fs/io-wq.h'
+rm -f 'fs/io_uring.c'
+rm -f 'include/asm-generic/bugs.h'
+rm -f 'include/linux/counter_enum.h'
+rm -f 'include/net/dn.h'
+rm -f 'include/net/dn_dev.h'
+rm -f 'include/net/dn_fib.h'
+rm -f 'include/net/dn_neigh.h'
+rm -f 'include/net/dn_nsp.h'
+rm -f 'include/net/dn_route.h'
+rm -f 'include/trace/events/random.h'
+rm -f 'include/trace/events/rdma.h'
+rm -f 'include/uapi/linux/dn.h'
+rm -f 'include/uapi/linux/netfilter_decnet.h'
+rm -f 'include/uapi/linux/nfsd/nfsfh.h'
+rm -f 'kernel/futex.c'
+rm -f 'net/decnet/Kconfig'
+rm -f 'net/decnet/Makefile'
+rm -f 'net/decnet/README'
+rm -f 'net/decnet/af_decnet.c'
+rm -f 'net/decnet/dn_dev.c'
+rm -f 'net/decnet/dn_fib.c'
+rm -f 'net/decnet/dn_neigh.c'
+rm -f 'net/decnet/dn_nsp_in.c'
+rm -f 'net/decnet/dn_nsp_out.c'
+rm -f 'net/decnet/dn_route.c'
+rm -f 'net/decnet/dn_rules.c'
+rm -f 'net/decnet/dn_table.c'
+rm -f 'net/decnet/dn_timer.c'
+rm -f 'net/decnet/netfilter/Kconfig'
+rm -f 'net/decnet/netfilter/Makefile'
+rm -f 'net/decnet/netfilter/dn_rtmsg.c'
+rm -f 'net/decnet/sysctl_net_decnet.c'
+rm -f 'net/qrtr/qrtr.c'
+rm -f 'net/sched/cls_rsvp.c'
+rm -f 'net/sched/cls_rsvp.h'
+rm -f 'net/sched/cls_rsvp6.c'
+rm -f 'net/sched/cls_tcindex.c'
+rm -f 'net/sched/sch_atm.c'
+rm -f 'net/sched/sch_cbq.c'
+rm -f 'net/sched/sch_dsmark.c'
+rm -f 'net/xfrm/xfrm_interface.c'
+rm -f 'tools/build/feature/test-libpython-version.c'
+rm -f 'tools/perf/arch/arm64/util/machine.c'
+rm -f 'tools/perf/arch/powerpc/util/machine.c'
+rm -f 'tools/perf/pmu-events/arch/powerpc/power10/floating_point.json'
+rm -f 'tools/perf/util/bpf_skel/bperf.h'
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/amd64.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/amd64.mk
@@ -0,0 +1,23 @@
+human_arch	= 64 bit x86
+build_arch	= x86
+header_arch	= $(build_arch)
+defconfig	= defconfig
+flavours	= generic
+build_image	= bzImage
+kernel_file	= arch/$(build_arch)/boot/bzImage
+install_file	= vmlinuz
+vdso		= vdso_install
+no_dumpfile	= true
+uefi_signed     = true
+do_tools_usbip  = true
+do_tools_cpupower = true
+do_tools_perf   = true
+do_tools_perf_jvmti = true
+do_tools_bpftool = true
+do_tools_x86	= true
+do_tools_hyperv	= true
+do_tools_host = true
+do_extras_package = true
+do_tools_common = true
+do_tools_acpidbg = true
+do_odm_drivers  = true
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/arm64.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/arm64.mk
@@ -0,0 +1,21 @@
+human_arch	= ARMv8
+build_arch	= arm64
+header_arch	= arm64
+defconfig	= defconfig
+flavours	= generic generic-64k
+build_image	= Image.gz
+kernel_file	= arch/$(build_arch)/boot/Image.gz
+install_file	= vmlinuz
+no_dumpfile = true
+uefi_signed     = true
+
+vdso		= vdso_install
+
+do_extras_package = true
+do_tools_usbip  = true
+do_tools_cpupower = true
+do_tools_perf   = true
+do_tools_perf_jvmti = true
+do_tools_bpftool = true
+
+do_dtbs		= true
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/armhf.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/armhf.mk
@@ -0,0 +1,17 @@
+human_arch	= ARM (hard float)
+build_arch	= arm
+header_arch	= arm
+defconfig	= defconfig
+flavours	= generic generic-lpae
+build_image	= zImage
+kernel_file	= arch/$(build_arch)/boot/zImage
+install_file	= vmlinuz
+no_dumpfile	= true
+
+do_tools_usbip  = true
+do_tools_cpupower = true
+do_tools_perf	= true
+do_tools_perf_jvmti = true
+do_tools_bpftool = true
+
+do_dtbs		= true
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/hooks.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/hooks.mk
@@ -0,0 +1 @@
+do_enforce_all = true
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/i386.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/i386.mk
@@ -0,0 +1,18 @@
+human_arch	= 32 bit x86
+build_arch	= i386
+header_arch	= $(build_arch)
+defconfig	= defconfig
+flavours        = generic
+build_image	= bzImage
+kernel_file	= arch/$(build_arch)/boot/bzImage
+install_file	= vmlinuz
+vdso		= vdso_install
+no_dumpfile	= true
+do_flavour_image_package = false
+do_tools	= false
+do_tools_common	= false
+do_extras_package = false
+do_source_package = false
+do_doc_package	= false
+do_flavour_header_package = false
+do_common_headers_indep = false
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/ppc64el.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/ppc64el.mk
@@ -0,0 +1,18 @@
+human_arch	= PowerPC 64el
+build_arch	= powerpc
+header_arch	= $(build_arch)
+defconfig	= pseries_le_defconfig
+flavours	= generic
+build_image	= vmlinux.strip
+kernel_file     = arch/powerpc/boot/vmlinux.strip
+install_file	= vmlinux
+no_dumpfile	= true
+do_extras_package = true
+opal_signed       = true
+do_tools_usbip    = true
+do_tools_cpupower = true
+do_tools_perf	  = true
+do_tools_perf_jvmti = true
+do_tools_bpftool  = true
+
+#do_flavour_image_package = false
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/riscv64.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/riscv64.mk
@@ -0,0 +1,20 @@
+human_arch	= RISC-V
+build_arch	= riscv
+header_arch	= $(build_arch)
+defconfig	= defconfig
+flavours        = generic
+build_image	= Image
+kernel_file	= arch/$(build_arch)/boot/Image
+install_file	= vmlinuz
+
+vdso		= vdso_install
+no_dumpfile	= true
+
+do_flavour_image_package = false
+do_tools	= false
+do_tools_common	= false
+do_extras_package = false
+do_source_package = false
+do_doc_package	= false
+do_flavour_header_package = false
+do_common_headers_indep = false
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/s390x.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/s390x.mk
@@ -0,0 +1,19 @@
+human_arch      = System 390x
+build_arch      = s390
+header_arch     = $(build_arch)
+defconfig       = defconfig
+flavours        = generic
+build_image	= bzImage
+kernel_file	= arch/$(build_arch)/boot/bzImage
+install_file	= vmlinuz
+
+vdso		= vdso_install
+no_dumpfile	= true
+
+do_extras_package = true
+sipl_signed       = true
+do_tools_usbip    = true
+do_tools_cpupower = true
+do_tools_perf     = true
+do_tools_perf_jvmti = true
+do_tools_bpftool  = true
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/rules.d/x32.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.master/rules.d/x32.mk
@@ -0,0 +1,13 @@
+human_arch	= 64 bit x86 (32 bit userspace)
+build_arch	= x86
+header_arch	= $(build_arch)
+defconfig	= defconfig
+flavours	= 
+build_image	= bzImage
+kernel_file	= arch/$(build_arch)/boot/bzImage
+install_file	= vmlinuz
+vdso		= vdso_install
+no_dumpfile	= true
+uefi_signed     = true
+
+do_flavour_image_package = false
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/tracking-bug
+++ linux-xilinx-zynqmp-5.15.0/debian.master/tracking-bug
@@ -0,0 +1 @@
+2110829 2025.05.19-1
--- linux-xilinx-zynqmp-5.15.0.orig/debian.master/upstream-stable
+++ linux-xilinx-zynqmp-5.15.0/debian.master/upstream-stable
@@ -0,0 +1,3 @@
+# The following upstream stable releases have been ported:
+[upstream-stable]
+    linux-5.15.y = v5.15.180
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/changelog
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/changelog
@@ -0,0 +1,31125 @@
+linux-xilinx-zynqmp (5.15.0-1050.54) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1050.54 -proposed tracker (LP: #2110826)
+
+  [ Ubuntu: 5.15.0-142.152 ]
+
+  * jammy/linux: 5.15.0-142.152 -proposed tracker (LP: #2110829)
+  * Rotate the Canonical Livepatch key (LP: #2111244)
+    - [Config] Prepare for Canonical Livepatch key rotation
+  * Jammy generic-64k fails to initialize gVNIC devices (LP: #2109537)
+    - gve: Perform adminq allocations through a dma_pool.
+    - gve: Deprecate adminq_pfn for pci revision 0x1.
+    - gve: Remove obsolete checks that rely on page size.
+    - gve: Add page size register to the register_page_list command.
+    - gve: Remove dependency on 4k page size.
+  * CVE-2025-2312 cifs.upcall could access incorrect kerberos credentials cache
+    (LP: #2099914) // CVE-2025-2312
+    - CIFS: New mount option for cifs.upcall namespace resolution
+  * [UBUNTU 22.04] net/smc: fix neighbour and rtable leak in smc_ib_find_route()
+    (LP: #2109601) // CVE-2024-36945
+    - net/smc: fix neighbour and rtable leak in smc_ib_find_route()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355)
+    - clockevents/drivers/i8253: Fix stop sequence for timer 0
+    - sched/isolation: Prevent boot crash when the boot CPU is nohz_full
+    - fbdev: hyperv_fb: iounmap() the correct memory when removing a device
+    - pinctrl: bcm281xx: Fix incorrect regmap max_registers value
+    - netfilter: nft_ct: Use __refcount_inc() for per-CPU nft_ct_pcpu_template.
+    - net: dsa: mv88e6xxx: Verify after ATU Load ops
+    - netpoll: hold rcu read lock in __netpoll_send_skb()
+    - Drivers: hv: vmbus: Don't release fb_mmio resource in vmbus_free_mmio()
+    - ipvs: prevent integer overflow in do_ip_vs_get_ctl()
+    - netfilter: nft_exthdr: fix offset with ipv4_find_option()
+    - gre: Fix IPv6 link-local address generation.
+    - slab: clean up function prototypes
+    - slab: Introduce kmalloc_size_roundup()
+    - openvswitch: Use kmalloc_size_roundup() to match ksize() usage
+    - net: openvswitch: remove misbehaving actions length check
+    - net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices
+    - nvme-fc: go straight to connecting state when initializing
+    - hrtimers: Mark is_migration_base() with __always_inline
+    - powercap: call put_device() on an error path in
+      powercap_register_control_type()
+    - scsi: core: Use GFP_NOIO to avoid circular locking dependency
+    - ACPI: resource: IRQ override for Eluktronics MECH-17
+    - alpha/elf: Fix misc/setarch test of util-linux by removing 32bit support
+    - vboxsf: fix building with GCC 15
+    - HID: intel-ish-hid: fix the length of MNG_SYNC_FW_CLOCK in doorbell
+    - sched: Clarify wake_up_q()'s write to task->wake_q.next
+    - s390/cio: Fix CHPID "configure" attribute caching
+    - thermal/cpufreq_cooling: Remove structure member documentation
+    - ASoC: rsnd: don't indicate warning on rsnd_kctrl_accept_runtime()
+    - ASoC: arizona/madera: use fsleep() in up/down DAPM event delays.
+    - ASoC: SOF: Intel: hda: add softdep pre to snd-hda-codec-hdmi module
+    - net: wwan: mhi_wwan_mbim: Silence sequence number glitch errors
+    - nvmet-rdma: recheck queue state is LIVE in state lock in recv done
+    - sctp: Fix undefined behavior in left shift operation
+    - nvme: only allow entering LIVE from CONNECTING state
+    - ASoC: tas2770: Fix volume scale
+    - ASoC: tas2764: Fix power control mask
+    - ASoC: tas2764: Set the SDOUT polarity correctly
+    - fuse: don't truncate cached, mutated symlink
+    - x86/irq: Define trace events conditionally
+    - mptcp: safety check before fallback
+    - drm/nouveau: Do not override forced connector status
+    - block: fix 'kmem_cache of name 'bio-108' already exists'
+    - USB: serial: ftdi_sio: add support for Altera USB Blaster 3
+    - USB: serial: option: add Telit Cinterion FE990B compositions
+    - USB: serial: option: fix Telit Cinterion FE990A name
+    - USB: serial: option: match on interface class for Telit FN990B
+    - drm/atomic: Filter out redundant DPMS calls
+    - drm/amd/display: Restore correct backlight brightness after a GPU reset
+    - qlcnic: fix memory leak issues in qlcnic_sriov_common.c
+    - lib/buildid: Handle memfd_secret() files in build_id_parse()
+    - tcp: fix races in tcp_abort()
+    - ASoC: ops: Consistently treat platform_max as control value
+    - drm/gma500: Add NULL check for pci_gfx_root in mid_get_vbt_data()
+    - ASoC: codecs: wm0010: Fix error handling path in wm0010_spi_probe()
+    - cifs: Fix integer overflow while processing actimeo mount option
+    - i2c: ali1535: Fix an error handling path in ali1535_probe()
+    - i2c: ali15x3: Fix an error handling path in ali15x3_probe()
+    - i2c: sis630: Fix an error handling path in sis630_probe()
+    - drm/amd/display: Check for invalid input params when building scaling params
+    - smb: client: Fix match_session bug preventing session reuse
+    - Revert "smb: client: fix potential UAF in cifs_debug_files_proc_show()"
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+    - firmware: imx-scu: fix OF node leak in .probe()
+    - xfrm_output: Force software GSO only in tunnel mode
+    - ARM: dts: bcm2711: PL011 UARTs are actually r1p5
+    - RDMA/bnxt_re: Add missing paranthesis in map_qp_id_to_tbl_indx
+    - ARM: dts: bcm2711: Don't mark timer regs unconfigured
+    - RDMA/bnxt_re: Avoid clearing VLAN_ID mask in modify qp path
+    - RDMA/hns: Remove redundant 'phy_addr' in hns_roce_hem_list_find_mtt()
+    - RDMA/hns: Fix unmatched condition in error path of alloc_user_qp_db()
+    - RDMA/hns: Fix a missing rollback in error path of
+      hns_roce_create_qp_common()
+    - RDMA/hns: Fix wrong value of max_sge_rd
+    - ipv6: Set errno after ip_fib_metrics_init() in ip6_route_info_create().
+    - net/neighbor: add missing policy for NDTPA_QUEUE_LENBYTES
+    - Revert "gre: Fix IPv6 link-local address generation."
+    - i2c: omap: fix IRQ storms
+    - drm/v3d: Don't run jobs that have errors flagged in its fence
+    - mmc: atmel-mci: Add missing clk_disable_unprepare()
+    - ARM: shmobile: smp: Enforce shmobile_smp_* alignment
+    - batman-adv: Ignore own maximum aggregation size during RX
+    - drm/amdgpu: Fix JPEG video caps max size for navi1x and raven
+    - mptcp: Fix data stream corruption in the address announcement
+    - arm64: dts: rockchip: fix u2phy1_host status for NanoPi R4S
+    - ALSA: usb-audio: Add quirk for Plantronics headsets to fix control names
+    - HID: hid-plantronics: Add mic mute mapping and generalize quirks
+    - ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed()
+    - ARM: 9351/1: fault: Add "cut here" line for prefetch aborts
+    - ARM: Remove address checking for MMUless devices
+    - ALSA: hda/realtek: Support mute LED on HP Laptop 15s-du3xxx
+    - counter: stm32-lptimer-cnt: fix error handling when enabling
+    - counter: microchip-tcb-capture: Fix undefined counter channel state on probe
+    - tty: serial: 8250: Add some more device IDs
+    - tty: serial: 8250: Add Brainboxes XC devices
+    - net: usb: qmi_wwan: add Telit Cinterion FN990B composition
+    - net: usb: qmi_wwan: add Telit Cinterion FE990B composition
+    - net: usb: usbnet: restore usb%d name exception for local mac addresses
+    - serial: 8250_dma: terminate correct DMA in tx_dma_flush()
+    - x86/mm/pat: cpa-test: fix length for CPA_ARRAY test
+    - cpufreq: scpi: compare kHz instead of Hz
+    - cpufreq: governor: Fix negative 'idle_time' handling in dbs_update()
+    - x86/fpu: Avoid copying dynamic FP state from init_task in
+      arch_dup_task_struct()
+    - x86/platform: Only allow CONFIG_EISA for 32-bit
+    - [Config] updateconfigs for HAVE_EISA
+    - PM: sleep: Adjust check before setting power.must_resume
+    - selinux: Chain up tool resolving errors in install_policy.sh
+    - EDAC/ie31200: Fix the size of EDAC_MC_LAYER_CHIP_SELECT layer
+    - EDAC/ie31200: Fix the DIMM size mask for several SoCs
+    - EDAC/ie31200: Fix the error path order of ie31200_init()
+    - PM: sleep: Fix handling devices with direct_complete set on errors
+    - lockdep: Don't disable interrupts on RT in disable_irq_nosync_lockdep.*()
+    - perf/ring_buffer: Allow the EPOLLRDNORM flag for poll
+    - media: platform: allgro-dvt: unregister v4l2_device on the error path
+    - HID: remove superfluous (and wrong) Makefile entry for
+      CONFIG_INTEL_ISH_FIRMWARE_DOWNLOADER
+    - ALSA: hda/realtek: Always honor no_shutup_pins
+    - ASoC: ti: j721e-evm: Fix clock configuration for ti,j7200-cpb-audio
+      compatible
+    - drm/bridge: ti-sn65dsi86: Fix multiple instances
+    - drm/dp_mst: Fix drm RAD print
+    - drm: xlnx: zynqmp: Fix max dma segment size
+    - drm/mediatek: mtk_hdmi: Unregister audio platform device on failure
+    - drm/mediatek: mtk_hdmi: Fix typo for aud_sampe_size member
+    - PCI: cadence-ep: Fix the driver to send MSG TLP for INTx without data
+      payload
+    - PCI: brcmstb: Use internal register to change link capability
+    - PCI/portdrv: Only disable pciehp interrupts early when needed
+    - PCI: Avoid reset when disabled via sysfs
+    - drm/amd/display: fix type mismatch in CalculateDynamicMetadataParameters()
+    - PCI: Remove stray put_device() in pci_register_host_bridge()
+    - PCI: xilinx-cpm: Fix IRQ domain leak in error path of probe
+    - drm/mediatek: dsi: fix error codes in mtk_dsi_host_transfer()
+    - PCI: pciehp: Don't enable HPIE when resuming in poll mode
+    - fbdev: au1100fb: Move a variable assignment behind a null pointer check
+    - mdacon: rework dependency list
+    - fbdev: sm501fb: Add some geometry checks.
+    - clk: amlogic: gxbb: drop incorrect flag on 32k clock
+    - crypto: hisilicon/sec2 - fix for aead authsize alignment
+    - of: property: Increase NR_FWNODE_REFERENCE_ARGS
+    - remoteproc: qcom_q6v5_pas: Make single-PD handling more robust
+    - libbpf: Fix hypothetical STT_SECTION extern NULL deref case
+    - clk: qcom: gcc-msm8953: fix stuck venus0_core0 clock
+    - bpf: Use preempt_count() directly in bpf_send_signal_common()
+    - lib: 842: Improve error handling in sw842_compress()
+    - pinctrl: renesas: rza2: Fix missing of_node_put() call
+    - pinctrl: renesas: rzg2l: Fix missing of_node_put() call
+    - clk: rockchip: rk3328: fix wrong clk_ref_usb3otg parent
+    - remoteproc: qcom_q6v5_mss: Handle platforms with one power domain
+    - IB/mad: Check available slots before posting receive WRs
+    - pinctrl: tegra: Set SFIO mode to Mux Register
+    - clk: amlogic: g12b: fix cluster A parent data
+    - clk: amlogic: gxbb: drop non existing 32k clock parent
+    - clk: amlogic: g12a: fix mmc A peripheral clock
+    - x86/entry: Fix ORC unwinder for PUSH_REGS with save_ret=1
+    - power: supply: max77693: Fix wrong conversion of charge input threshold
+      value
+    - crypto: nx - Fix uninitialised hv_nxc on error
+    - mfd: sm501: Switch to BIT() to mitigate integer overflows
+    - x86/dumpstack: Fix inaccurate unwinding from exception stacks due to
+      misplaced assignment
+    - crypto: hisilicon/sec2 - fix for aead auth key length
+    - clk: qcom: mmcc-sdm660: fix stuck video_subcore0 clock
+    - isofs: fix KMSAN uninit-value bug in do_isofs_readdir()
+    - soundwire: slave: fix an OF node reference leak in soundwire slave device
+    - coresight: catu: Fix number of pages while using 64k pages
+    - iio: accel: mma8452: Ensure error return on failure to matching oversampling
+      ratio
+    - iio: adc: ad7124: Fix comparison of channel configs
+    - perf units: Fix insufficient array space
+    - kexec: initialize ELF lowest address to ULONG_MAX
+    - NFSv4: Don't trigger uneccessary scans for return-on-close delegations
+    - fuse: fix dax truncate/punch_hole fault path
+    - i3c: master: svc: Fix missing the IBI rules
+    - perf python: Fixup description of sample.id event member
+    - perf python: Decrement the refcount of just created event on failure
+    - perf python: Don't keep a raw_data pointer to consumed ring buffer space
+    - perf python: Check if there is space to copy all the event
+    - fs/procfs: fix the comment above proc_pid_wchan()
+    - objtool, media: dib8000: Prevent divide-by-zero in dib8000_set_dds()
+    - exfat: fix the infinite loop in exfat_find_last_cluster()
+    - ksmbd: fix multichannel connection failure
+    - ring-buffer: Fix bytes_dropped calculation issue
+    - ACPI: processor: idle: Return an error if both P_LVL{2,3} idle states are
+      invalid
+    - octeontx2-af: Fix mbox INTR handler when num VFs > 64
+    - octeontx2-af: Free NIX_AF_INT_VEC_GEN irq
+    - sched/smt: Always inline sched_smt_active()
+    - wifi: iwlwifi: fw: allocate chained SG tables for dump
+    - nvme-tcp: fix possible UAF in nvme_tcp_poll
+    - nvme-pci: clean up CMBMSC when registering CMB fails
+    - nvme-pci: skip CMB blocks incompatible with PCI P2P DMA
+    - affs: generate OFS sequence numbers starting at 1
+    - affs: don't write overlarge OFS data block size fields
+    - sched/deadline: Use online cpus for validating runtime
+    - locking/semaphore: Use wake_q to wake up processes outside lock critical
+      section
+    - x86/sgx: Warn explicitly if X86_FEATURE_SGX_LC is not enabled
+    - drm/amd: Keep display off while going into S4
+    - ALSA: hda/realtek: Add mute LED quirk for HP Pavilion x360 14-dy1xxx
+    - can: statistics: use atomic access in hot path
+    - hwmon: (nct6775-core) Fix out of bounds access for NCT679{8,9}
+    - riscv: ftrace: Add parentheses in macro definitions of make_call_t0 and
+      make_call_ra
+    - ntb: intel: Fix using link status DB's
+    - netfilter: nft_set_hash: GC reaps elements with conncount for dynamic sets
+      only
+    - vsock: avoid timeout during connect() if the socket is closing
+    - tunnels: Accept PACKET_HOST in skb_tunnel_check_pmtu().
+    - ipv6: fix omitted netlink attributes when using RTEXT_FILTER_SKIP_STATS
+    - can: flexcan: only change CAN state when link up in system PM
+    - can: flexcan: disable transceiver during system PM
+    - mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0
+    - mmc: sdhci-brcmstb: add cqhci suspend/resume to PM ops
+    - tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
+    - tty: serial: fsl_lpuart: disable transmitter before changing RS485 related
+      registers
+    - platform/x86: ISST: Correct command storage data length
+    - ntb_perf: Delete duplicate dmaengine_unmap_put() call in perf_copy_chunk()
+    - x86/tsc: Always save/restore TSC sched_clock() on suspend/resume
+    - ACPI: resource: Skip IRQ override on ASUS Vivobook 14 X1404VAP
+    - mmc: sdhci-pxav3: set NEED_RSP_BUSY capability
+    - tracing: Ensure module defining synth event cannot be unloaded while tracing
+    - tracing: Fix synth event printk format for str fields
+    - tracing/osnoise: Fix possible recursive locking for cpus_read_lock()
+    - ext4: don't over-report free space or inodes in statvfs
+    - jfs: add index corruption check to DT_GETPAGE()
+    - NFSD: Skip sending CB_RECALL_ANY when the backchannel isn't up
+    - mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
+    - mm, slab: remove duplicate kernel-doc comment for ksize()
+    - tracing: Do not use PERF enums when perf is not defined
+    - mmc: sdhci-brcmstb: Initialize base_clk to NULL in sdhci_brcmstb_probe()
+    - Linux 5.15.180
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22025
+    - nfsd: put dl_stid if fail to queue dl_recall
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-39735
+    - jfs: fix slab-out-of-bounds read in ea_get()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-37785
+    - ext4: fix OOB read when checking dotdot dir
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22035
+    - tracing: Fix use-after-free in print_graph_function_flags during tracer
+      switching
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22044
+    - acpi: nfit: fix narrowing conversion in acpi_nfit_ctl
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22045
+    - x86/mm: Fix flush_tlb_range() when used for zapping normal PMDs
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46753
+    - btrfs: handle errors from btrfs_dec_ref() properly
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22050
+    - usbnet:fix NPE during rx_complete
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46812
+    - drm/amd/display: Skip inactive planes within
+      ModeSupportAndSystemConfiguration
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46821
+    - drm/amd/pm: Fix negative array index read
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22054
+    - arcnet: Add NULL check in com20020pci_probe()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22055
+    - net: fix geneve_opt length integer overflow
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22056
+    - netfilter: nft_tunnel: fix geneve_opt type confusion addition
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22060
+    - net: mvpp2: Prevent parser TCAM memory corruption
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38637
+    - net_sched: skbprio: Remove overly strict queue assertions
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22063
+    - netlabel: Fix NULL pointer exception caused by CALIPSO on IPv4 sockets
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22066
+    - ASoC: imx-card: Add NULL check in imx_card_probe()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2023-53034
+    - ntb_hw_switchtec: Fix shift-out-of-bounds in switchtec_ntb_mw_set_trans
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22071
+    - spufs: fix a leak in spufs_create_context()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22073
+    - spufs: fix a leak on spufs_new_file() failure
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21994
+    - ksmbd: fix incorrect validation for num_aces field of smb_acl
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38575
+    - ksmbd: use aead_request_free to match aead_request_alloc
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22075
+    - rtnetlink: Allocate vfinfo size for VF GUIDs when supported
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22079
+    - ocfs2: validate l_tree_depth to avoid out-of-bounds access
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22081
+    - fs/ntfs3: Fix a couple integer overflows on 32bit systems
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22086
+    - RDMA/mlx5: Fix mlx5_poll_one() cur_qp update flow
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22089
+    - RDMA/core: Don't expose hw_counters outside of init net namespace
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-39728
+    - clk: samsung: Fix UBSAN panic in samsung_clk_init()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38152
+    - remoteproc: core: Clear table_sz when rproc_shutdown
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-58093
+    - PCI/ASPM: Fix link state exit during switch upstream function removal
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22097
+    - drm/vkms: Fix use after free and double free on init error
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-23136
+    - thermal: int340x: Add NULL check for adev
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-23138
+    - watch_queue: fix pipe accounting mismatch
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22020
+    - memstick: rtsx_usb_ms: Fix slab-use-after-free in rtsx_usb_ms_drv_remove
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22021
+    - netfilter: socket: Lookup orig tuple for IPv6 SNAT
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22018
+    - atm: Fix NULL pointer dereference
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-56664
+    - bpf, sockmap: Fix race between element replace and close()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-53144 // CVE-2024-8805
+    - Bluetooth: hci_event: Align BR/EDR JUST_WORKS paring with LE
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21996
+    - drm/radeon: fix uninitialized size issue in radeon_vce_cs_parse()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22014
+    - soc: qcom: pdr: Fix the potential deadlock
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21999
+    - proc: fix UAF in proc_get_inode()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22008
+    - regulator: check that dummy regulator has been probed before using it
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22004
+    - net: atm: fix use after free in lec_send()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22005
+    - ipv6: Fix memleak of nhc_pcpu_rth_output in fib_check_nh_v6_gw().
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22007
+    - Bluetooth: Fix error code in chan_alloc_skb_cb()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22010
+    - RDMA/hns: Fix soft lockup during bt pages loop
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21941
+    - drm/amd/display: Fix null check for pipe_ctx->plane_state in
+      resource_build_scaling_params
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21962
+    - cifs: Fix integer overflow while processing closetimeo mount option
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21963
+    - cifs: Fix integer overflow while processing acdirmax mount option
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21964
+    - cifs: Fix integer overflow while processing acregmax mount option
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21968
+    - drm/amd/display: Fix slab-use-after-free on hdcp_work
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21956
+    - drm/amd/display: Assign normalized_pix_clk when color depth = 14
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21991
+    - x86/microcode/AMD: Fix out-of-bounds on systems with CPU-less NUMA nodes
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21992
+    - HID: ignore non-functional sensor in HP 5MP Camera
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21957
+    - scsi: qla1280: Fix kernel oops when debug level > 2
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21970
+    - net/mlx5: Bridge, fix the crash caused by LAG state check
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21959
+    - netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in
+      insert_tree()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21975
+    - net/mlx5: handle errors in mlx5_chains_create_table()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21981
+    - ice: fix memory leak in aRFS after reset
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2022-49728
+    - ipv6: Fix signed integer overflow in __ip6_append_data
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2022-49636
+    - vlan: fix memory leak in vlan_newlink()
+  * VM boots slowly with large-BAR GPU Passthrough due to pci/probe.c redundancy
+    (LP: #2097389)
+    - PCI: Batch BAR sizing operations
+  * kexec fails in LPAR when some cpus are disabled (LP: #2075575)
+    - powerpc/pseries: Fix scv instruction crash with kexec
+  * CVE-2024-56608
+    - drm/amd/display: Fix out-of-bounds access in 'dcn21_link_encoder_create'
+  * CVE-2024-53168
+    - net: make sock_inuse_add() available
+    - sunrpc: fix one UAF issue caused by sunrpc kernel tcp socket
+  * CVE-2024-56551
+    - drm/amdgpu: fix usage slab after free
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 06 Jun 2025 13:34:47 +0800
+
+linux-xilinx-zynqmp (5.15.0-1049.53) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1049.53 -proposed tracker (LP: #2111049)
+
+  [ Ubuntu: 5.15.0-141.151 ]
+
+  * jammy/linux: 5.15.0-141.151 -proposed tracker (LP: #2111052)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+  * CVE-2024-56608
+    - drm/amd/display: Fix out-of-bounds access in 'dcn21_link_encoder_create'
+  * CVE-2024-53168
+    - net: make sock_inuse_add() available
+    - sunrpc: fix one UAF issue caused by sunrpc kernel tcp socket
+  * CVE-2024-56551
+    - drm/amdgpu: fix usage slab after free
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Wed, 28 May 2025 13:53:46 +0800
+
+linux-xilinx-zynqmp (5.15.0-1048.52) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1048.52 -proposed tracker (LP: #2106990)
+
+  [ Ubuntu: 5.15.0-140.150 ]
+
+  * jammy/linux: 5.15.0-140.150 -proposed tracker (LP: #2106996)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.04.14)
+  * NFS, overlay, fstab issue after update to kernel 5.15.0-133-generic and -134
+    (LP: #2103598)
+    - udf: Fix directory iteration for longer tail extents
+  * Remove floppy kernel module causes null pointer deference (LP: #2104326)
+    - floppy: fix add_disk() assumption on exit due to new developments
+  * CVE-2025-21971
+    - net_sched: Prevent creation of classes with TC_H_ROOT
+  * CVE-2024-56599
+    - wifi: ath10k: avoid NULL pointer error during sdio remove
+  * CVE-2024-56721
+    - x86/CPU/AMD: Terminate the erratum_1386_microcode array
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026)
+    - afs: Fix EEXIST error returned from afs_rmdir() to be ENOTEMPTY
+    - afs: Fix directory format encoding struct
+    - hung_task: move hung_task sysctl interface to hung_task.c
+    - sysctl: use const for typically used max/min proc sysctls
+    - sysctl: share unsigned long const values
+    - fs: move inode sysctls to its own file
+    - fs: move fs stat sysctls to file_table.c
+    - fs: fix proc_handler for sysctl_nr_open
+    - block: deprecate autoloading based on dev_t
+    - block: retry call probe after request_module in blk_request_module
+    - pstore/blk: trivial typo fixes
+    - nvme: Add error check for xa_store in nvme_get_effects_log
+    - partitions: ldm: remove the initial kernel-doc notation
+    - select: Fix unbalanced user_access_end()
+    - afs: Fix the fallback handling for the YFS.RemoveFile2 RPC call
+    - sched/psi: Use task->psi_flags to clear in CPU migration
+    - sched/fair: Fix value reported by hot tasks pulled in /proc/schedstat
+    - drm/etnaviv: Fix page property being used for non writecombine buffers
+    - genirq: Make handle_enforce_irqctx() unconditionally available
+    - wifi: rtlwifi: do not complete firmware loading needlessly
+    - wifi: rtlwifi: rtl8192se: rise completion of firmware loading as last step
+    - wifi: rtlwifi: wait for firmware loading before releasing memory
+    - wifi: rtlwifi: fix init_sw_vars leak when probe fails
+    - wifi: rtlwifi: usb: fix workqueue leak when probe fails
+    - spi: zynq-qspi: Add check for clk_enable()
+    - dt-bindings: mmc: controller: clarify the address-cells description
+    - spi: dt-bindings: add schema listing peripheral-specific properties
+    - dt-bindings: Another pass removing cases of 'allOf' containing a '$ref'
+    - dt-bindings: leds: Add Qualcomm Light Pulse Generator binding
+    - dt-bindings: leds: Optional multi-led unit address
+    - dt-bindings: leds: Add multicolor PWM LED bindings
+    - dt-bindings: leds: class-multicolor: reference class directly in multi-led
+      node
+    - dt-bindings: leds: class-multicolor: Fix path to color definitions
+    - rtlwifi: replace usage of found with dedicated list iterator variable
+    - wifi: rtlwifi: remove unused timer and related code
+    - wifi: rtlwifi: remove unused dualmac control leftovers
+    - wifi: rtlwifi: destroy workqueue at rtl_deinit_core
+    - wifi: rtlwifi: pci: wait for firmware loading before releasing memory
+    - HID: multitouch: Add support for lenovo Y9000P Touchpad
+    - Revert "HID: multitouch: Add support for lenovo Y9000P Touchpad"
+    - HID: multitouch: fix support for Goodix PID 0x01e9
+    - regulator: dt-bindings: mt6315: Drop regulator-compatible property
+    - ACPI: fan: cleanup resources in the error path of .probe()
+    - cpupower: fix TSC MHz calculation
+    - dt-bindings: mfd: bd71815: Fix rsense and typos
+    - leds: netxbig: Fix an OF node reference leak in netxbig_leds_get_of_pdata()
+    - cpufreq: schedutil: Fix superfluous updates caused by need_freq_update
+    - clk: imx8mp: Fix clkout1/2 support
+    - regulator: of: Implement the unwind path of of_regulator_match()
+    - samples/landlock: Fix possible NULL dereference in parse_path()
+    - wifi: wlcore: fix unbalanced pm_runtime calls
+    - net/smc: fix data error when recvmsg with MSG_PEEK flag
+    - landlock: Move filesystem helpers and add a new one
+    - wifi: mt76: mt76u_vendor_request: Do not print error messages when -EPROTO
+    - cpufreq: ACPI: Fix max-frequency computation
+    - selftests: harness: fix printing of mismatch values in __EXPECT()
+    - wifi: cfg80211: Handle specific BSSID in 6GHz scanning
+    - wifi: cfg80211: adjust allocation of colocated AP data
+    - clk: analogbits: Fix incorrect calculation of vco rate delta
+    - selftests/landlock: Fix error message
+    - net/mlxfw: Drop hard coded max FW flash image size
+    - netfilter: nft_flow_offload: update tcp state flags under lock
+    - tcp_cubic: fix incorrect HyStart round start detection
+    - tools/testing/selftests/bpf/test_tc_tunnel.sh: Fix wait for server bind
+    - libbpf: Fix segfault due to libelf functions not setting errno
+    - ASoC: sun4i-spdif: Add clock multiplier settings
+    - perf header: Fix one memory leakage in process_bpf_btf()
+    - perf header: Fix one memory leakage in process_bpf_prog_info()
+    - perf bpf: Fix two memory leakages when calling
+      perf_env__insert_bpf_prog_info()
+    - ASoC: renesas: rz-ssi: Use only the proper amount of dividers
+    - ktest.pl: Remove unused declarations in run_bisect_test function
+    - crypto: hisilicon/sec - add some comments for soft fallback
+    - crypto: hisilicon/sec - delete redundant blank lines
+    - crypto: hisilicon/sec2 - optimize the error return process
+    - crypto: hisilicon/sec2 - fix for aead icv error
+    - crypto: hisilicon/sec2 - fix for aead invalid authsize
+    - crypto: ixp4xx - fix OF node reference leaks in init_ixp_crypto()
+    - padata: fix sysfs store callback check
+    - perf top: Don't complain about lack of vmlinux when not resolving some
+      kernel samples
+    - perf report: Fix misleading help message about --demangle
+    - padata: add pd get/put refcnt helper
+    - ARM: at91: pm: change BU Power Switch to automatic mode
+    - arm64: dts: mt8183: set DMIC one-wire mode on Damu
+    - arm64: dts: mediatek: mt8516: fix GICv2 range
+    - arm64: dts: mediatek: mt8516: fix wdt irq type
+    - arm64: dts: mediatek: mt8516: remove 2 invalid i2c clocks
+    - arm64: dts: mediatek: mt8516: add i2c clock-div property
+    - arm64: dts: mediatek: mt8516: reserve 192 KiB for TF-A
+    - RDMA/mlx4: Avoid false error about access to uninitialized gids array
+    - arm64: dts: mediatek: mt8173-evb: Drop regulator-compatible property
+    - arm64: dts: mediatek: mt8173-elm: Drop regulator-compatible property
+    - arm64: dts: mediatek: mt8173-elm: Fix MT6397 PMIC sub-node names
+    - arm64: dts: mediatek: mt8173-evb: Fix MT6397 PMIC sub-node names
+    - arm64: dts: mediatek: mt8183: kenzo: Support second source touchscreen
+    - arm64: dts: mediatek: mt8183: willow: Support second source touchscreen
+    - memory: Add LPDDR2-info helpers
+    - memory: tegra20-emc: Support matching timings by LPDDR2 configuration
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Drop pp3300_panel voltage
+      settings
+    - arm64: dts: qcom: msm8996: Fix up USB3 interrupts
+    - arm64: dts: qcom: msm8994: Describe USB interrupts
+    - arm64: dts: qcom: msm8916: correct sleep clock frequency
+    - arm64: dts: qcom: msm8994: correct sleep clock frequency
+    - arm64: dts: qcom: sc7280: correct sleep clock frequency
+    - arm64: dts: qcom: sm6125: correct sleep clock frequency
+    - arm64: dts: qcom: sm8250: correct sleep clock frequency
+    - arm64: dts: qcom: sm8350: correct sleep clock frequency
+    - arm64: dts: qcom: sm8150-microsoft-surface-duo: fix typos in da7280
+      properties
+    - arm64: dts: qcom: sdm845: Fix interrupt types of camss interrupts
+    - ARM: dts: mediatek: mt7623: fix IR nodename
+    - fbdev: omapfb: Fix an OF node leak in dss_of_port_get_parent_device()
+    - RDMA/mlx5: Remove iova from struct mlx5_core_mkey
+    - RDMA/mlx5: Enforce umem boundaries for explicit ODP page faults
+    - RDMA/mlx5: Fix indirect mkey ODP page count
+    - xen/x86: free_p2m_page: use memblock_free_ptr() to free a virtual pointer
+    - memblock: drop memblock_free_early_nid() and memblock_free_early()
+    - of: reserved-memory: Do not make kmemleak ignore freed address
+    - efi: sysfb_efi: fix W=1 warnings when EFI is not set
+    - media: rc: iguanair: handle timeouts
+    - media: lmedm04: Handle errors for lme2510_int_read
+    - PCI: endpoint: Destroy the EPC device in devm_pci_epc_destroy()
+    - media: marvell: Add check for clk_enable()
+    - media: i2c: imx412: Add missing newline to prints
+    - media: i2c: ov9282: Correct the exposure offset
+    - media: mipi-csis: Add check for clk_enable()
+    - media: camif-core: Add check for clk_enable()
+    - media: uvcvideo: Propagate buf->error to userspace
+    - mtd: hyperbus: Make hyperbus_unregister_device() return void
+    - mtd: hyperbus: hbmc-am654: Convert to platform remove callback returning
+      void
+    - mtd: hyperbus: hbmc-am654: fix an OF node reference leak
+    - staging: media: imx: fix OF node leak in imx_media_add_of_subdevs()
+    - scsi: mpt3sas: Set ioc->manu_pg11.EEDPTagMode directly to 1
+    - scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
+    - ocfs2: mark dquot as inactive if failed to start trans while releasing dquot
+    - module: Extend the preempt disabled section in
+      dereference_symbol_descriptor().
+    - NFSv4.2: fix COPY_NOTIFY xdr buf size calculation
+    - NFSv4.2: mark OFFLOAD_CANCEL MOVEABLE
+    - tools/bootconfig: Fix the wrong format specifier
+    - xfrm: replay: Fix the update of replay_esn->oseq_hi for GSO
+    - dmaengine: ti: edma: fix OF node reference leaks in edma_driver
+    - gpio: mxc: remove dead code after switch to DT-only
+    - net: fec: implement TSO descriptor cleanup
+    - PM: hibernate: Add error handling for syscore_suspend()
+    - net: netdevsim: try to close UDP port harness races
+    - ptp: Properly handle compat ioctls
+    - perf trace: Fix runtime error of index out of bounds
+    - vsock: Allow retrying on connect() failure
+    - bgmac: reduce max frame size to support just MTU 1500
+    - net: sh_eth: Fix missing rtnl lock in suspend/resume path
+    - net: hsr: fix fill_frame_info() regression vs VLAN packets
+    - genksyms: fix memory leak when the same symbol is added from source
+    - genksyms: fix memory leak when the same symbol is read from *.symref file
+    - kconfig: fix file name in warnings when loading KCONFIG_DEFCONFIG_LIST
+    - kconfig: add warn-unknown-symbols sanity check
+    - kconfig: require a space after '#' for valid input
+    - kconfig: remove unused code for S_DEF_AUTO in conf_read_simple()
+    - kconfig: deduplicate code in conf_read_simple()
+    - kconfig: WERROR unmet symbol dependency
+    - kconfig: fix memory leak in sym_warn_unmet_dep()
+    - hexagon: fix using plain integer as NULL pointer warning in cmpxchg
+    - hexagon: Fix unbalanced spinlock in die()
+    - f2fs: Introduce linear search for dentries
+    - ktest.pl: Check kernelrelease return in get_version
+    - ALSA: usb-audio: Add delay quirk for iBasso DC07 Pro
+    - drivers/card_reader/rtsx_usb: Restore interrupt based detection
+    - usb: gadget: f_tcm: Fix Get/SetInterface return value
+    - usb: dwc3: core: Defer the probe until USB power supply ready
+    - usb: typec: tcpm: set SRC_SEND_CAPABILITIES timeout to PD_T_SENDER_RESPONSE
+    - usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS
+    - btrfs: output the reason for open_ctree() failure
+    - btrfs: fix data race when accessing the inode's disk_i_size at
+      btrfs_drop_extents()
+    - btrfs: convert BUG_ON in btrfs_reloc_cow_block() to proper error handling
+    - sched: Don't try to catch up excess steal time.
+    - lockdep: Fix upper limit for LOCKDEP_*_BITS configs
+    - x86/amd_nb: Restrict init function to AMD-based systems
+    - tun: fix group permission check
+    - mmc: core: Respect quirk_max_rate for non-UHS SDIO card
+    - mfd: lpc_ich: Add another Gemini Lake ISA bridge PCI device-id
+    - HID: Wacom: Add PCI Wacom device support
+    - net/mlx5: use do_aux_work for PHC overflow checks
+    - wifi: iwlwifi: avoid memory leak
+    - i2c: Force ELAN06FA touchpad I2C bus freq to 100KHz
+    - APEI: GHES: Have GHES honor the panic= setting
+    - net: wwan: iosm: Fix hibernation by re-binding the driver around it
+    - mmc: sdhci-msm: Correctly set the load for the regulator
+    - tipc: re-order conditions in tipc_crypto_key_rcv()
+    - selftests/net/ipsec: Fix Null pointer dereference in rtattr_pack()
+    - Input: allocate keycode for phone linking
+    - platform/x86: acer-wmi: Ignore AC events
+    - x86/mm: Don't disable PCID when INVLPG has been fixed by microcode
+    - usb: chipidea: ci_hdrc_imx: use dev_err_probe()
+    - usb: chipidea/ci_hdrc_imx: Convert to platform remove callback returning
+      void
+    - usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in
+      the error path of .probe()
+    - net/ncsi: Add NC-SI 1.2 Get MC MAC Address command
+    - net/ncsi: fix locking in Get MAC Address handling
+    - xfs: report realtime block quota limits on realtime directories
+    - xfs: don't over-report free space or inodes in statvfs
+    - usb: xhci: Add timeout argument in address_device USB HCD callback
+    - nvme: handle connectivity loss in nvme_set_queue_count
+    - firmware: iscsi_ibft: fix ISCSI_IBFT Kconfig entry
+    - gpu: drm_dp_cec: fix broken CEC adapter properties check
+    - tg3: Disable tg3 PCIe AER on system reboot
+    - udp: gso: do not drop small packets when PMTU reduces
+    - gpio: pca953x: Improve interrupt support
+    - net: atlantic: fix warning during hot unplug
+    - x86/xen: fix xen_hypercall_hvm() to not clobber %rbx
+    - x86/xen: add FRAME_END to xen_hypercall_hvm()
+    - tun: revert fix group permission check
+    - cpufreq: s3c64xx: Fix compilation warning
+    - leds: lp8860: Write full EEPROM, not only half of it
+    - drm/modeset: Handle tiled displays in pan_display_atomic.
+    - s390/futex: Fix FUTEX_OP_ANDN implementation
+    - m68k: vga: Fix I/O defines
+    - arm64: dts: rockchip: increase gmac rx_delay on rk3399-puma
+    - KVM: s390: vsie: fix some corner-cases when grabbing vsie pages
+    - drm/amd/pm: Mark MM activity as unsupported
+    - drm/komeda: Add check for komeda_get_layer_fourcc_list()
+    - drm/i915: Drop 64bpp YUV formats from ICL+ SDR planes
+    - Bluetooth: L2CAP: accept zero as a special value for MTU auto-selection
+    - clk: sunxi-ng: a100: enable MMC clock reparenting
+    - clk: qcom: clk-alpha-pll: fix alpha mode configuration
+    - clk: qcom: gcc-mdm9607: Fix cmd_rcgr offset for blsp1_uart6 rcg
+    - clk: qcom: clk-rpmh: prevent integer overflow in recalc_rate
+    - efi: libstub: Use '-std=gnu11' to fix build with GCC 15
+    - perf bench: Fix undefined behavior in cmpworker()
+    - of: Correct child specifier used as input of the 2nd nexus node
+    - of: Fix of_find_node_opts_by_path() handling of alias+path+options
+    - of: reserved-memory: Fix using wrong number of cells to get property
+      'alignment'
+    - HID: hid-sensor-hub: don't use stale platform-data on remove
+    - wifi: rtlwifi: rtl8821ae: Fix media status report
+    - usb: gadget: f_tcm: Translate error to sense
+    - usb: gadget: f_tcm: Decrement command ref count on cleanup
+    - usb: gadget: f_tcm: ep_autoconfig with fullspeed endpoint
+    - usb: gadget: f_tcm: Don't prepare BOT write request twice
+    - serial: sh-sci: Drop __initdata macro for port_cfg
+    - serial: sh-sci: Do not probe the serial port if its slot in sci_ports[] is
+      in use
+    - MIPS: Loongson64: remove ROM Size unit in boardinfo
+    - powerpc/pseries/eeh: Fix get PE state translation
+    - dm-crypt: don't update io->sector after kcryptd_crypt_write_io_submit()
+    - dm-crypt: track tag_offset in convert_context
+    - mips/math-emu: fix emulation of the prefx instruction
+    - ALSA: hda/realtek: Enable headset mic on Positivo C6400
+    - PCI: endpoint: Finish virtual EP removal in pci_epf_remove_vepf()
+    - nvme-pci: Add TUXEDO InfinityFlex to Samsung sleep quirk
+    - nvme-pci: Add TUXEDO IBP Gen9 to Samsung sleep quirk
+    - scsi: qla2xxx: Move FCE Trace buffer allocation to user control
+    - scsi: storvsc: Set correct data length for sending SCSI command without
+      payload
+    - kbuild: Move -Wenum-enum-conversion to W=2
+    - x86/boot: Use '-std=gnu11' to fix build with GCC 15
+    - arm64: dts: qcom: sm8350: Fix MPSS memory length
+    - crypto: qce - fix priority to be less than ARMv8 CE
+    - xfs: Add error handling for xfs_reflink_cancel_cow_range
+    - media: ccs: Clean up parsed CCS static data on parse failure
+    - iio: light: as73211: fix channel handling in only-color triggered buffer
+    - soc: qcom: smem_state: fix missing of_node_put in error path
+    - media: mc: fix endpoint iteration
+    - media: ov5640: fix get_light_freq on auto
+    - media: ccs: Fix CCS static data parsing for large block sizes
+    - media: ccs: Fix cleanup order in ccs_probe()
+    - media: uvcvideo: Fix event flags in uvc_ctrl_send_events
+    - media: uvcvideo: Remove redundant NULL assignment
+    - crypto: qce - fix goto jump in error path
+    - crypto: qce - unregister previously registered algos in error path
+    - nvmem: qcom-spmi-sdam: Set size in struct nvmem_config
+    - nvmem: core: improve range check for nvmem_cell_write()
+    - vfio/platform: check the bounds of read/write syscalls
+    - pnfs/flexfiles: retry getting layout segment for reads
+    - ocfs2: fix incorrect CPU endianness conversion causing mount failure
+    - mtd: onenand: Fix uninitialized retlen in do_otp_read()
+    - misc: fastrpc: Fix registered buffer page address
+    - net/ncsi: wait for the last response to Deselect Package before configuring
+      channel
+    - net: phy: c45-tjaxx: add delay between MDIO write and read in soft_reset
+    - MIPS: ftrace: Declare ftrace_get_parent_ra_addr() as static
+    - net/ncsi: use dev_set_mac_address() for Get MC MAC Address handling
+    - gpio: xilinx: remove excess kernel doc
+    - memory: tegra20-emc: Correct memory device mask
+    - ocfs2: check dir i_size in ocfs2_find_entry
+    - mptcp: prevent excessive coalescing on receive
+    - ndisc: ndisc_send_redirect() must use dev_get_by_index_rcu()
+    - drm/i915/selftests: avoid using uninitialized context
+    - gpio: bcm-kona: Fix GPIO lock/unlock for banks above bank 0
+    - gpio: bcm-kona: Make sure GPIO bits are unlocked when requesting IRQ
+    - gpio: bcm-kona: Add missing newline to dev_err format string
+    - xen: remove a confusing comment on auto-translated guest I/O
+    - x86/xen: allow larger contiguous memory regions in PV guests
+    - media: cxd2841er: fix 64-bit division on gcc-9
+    - PCI/DPC: Quirk PIO log size for Intel Raptor Lake-P
+    - vfio/pci: Enable iowrite64 and ioread64 for vfio pci
+    - Grab mm lock before grabbing pt lock
+    - x86/mm/tlb: Only trim the mm_cpumask once a second
+    - ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet 5V
+    - batman-adv: Ignore neighbor throughput metrics in error case
+    - perf/x86/intel: Ensure LBRs are disabled when a CPU is starting
+    - usb: roles: set switch registered flag early on
+    - usb: gadget: udc: renesas_usb3: Fix compiler warning
+    - usb: dwc2: gadget: remove of_node reference upon udc_stop
+    - USB: pci-quirks: Fix HCCPARAMS register error for LS7A EHCI
+    - usb: core: fix pipe creation for get_bMaxPacketSize0
+    - USB: quirks: add USB_QUIRK_NO_LPM quirk for Teclast dist
+    - USB: Add USB_QUIRK_NO_LPM quirk for sony xperia xz1 smartphone
+    - USB: cdc-acm: Fill in Renesas R-Car D3 USB Download mode quirk
+    - usb: cdc-acm: Fix handling of oversized fragments
+    - USB: serial: option: add MeiG Smart SLM828
+    - USB: serial: option: add Telit Cinterion FN990B compositions
+    - USB: serial: option: fix Telit Cinterion FN990A name
+    - USB: serial: option: drop MeiG Smart defines
+    - can: c_can: fix unbalanced runtime PM disable in error path
+    - can: j1939: j1939_sk_send_loop(): fix unable to send messages with data
+      length zero
+    - alpha: make stack 16-byte aligned (most cases)
+    - efi: Avoid cold plugged memory for placing the kernel
+    - cgroup: fix race between fork and cgroup.kill
+    - serial: 8250: Fix fifo underflow on flush
+    - alpha: align stack for page fault and user unaligned trap handlers
+    - gpio: stmpe: Check return value of stmpe_reg_read in
+      stmpe_gpio_irq_sync_unlock
+    - regmap-irq: Add missing kfree()
+    - arm64: Handle .ARM.attributes section in linker scripts
+    - mlxsw: Add return value check for mlxsw_sp_port_get_stats_raw()
+    - btrfs: fix hole expansion when writing at an offset beyond EOF
+    - clocksource: Replace cpumask_weight() with cpumask_empty()
+    - clocksource: Use pr_info() for "Checking clocksource synchronization"
+      message
+    - ipv4: add RCU protection to ip4_dst_hoplimit()
+    - net: treat possible_net_t net pointer as an RCU one and add read_pnet_rcu()
+    - net: add dev_net_rcu() helper
+    - ipv4: use RCU protection in rt_is_expired()
+    - ipv4: use RCU protection in inet_select_addr()
+    - Namespaceify min_pmtu sysctl
+    - Namespaceify mtu_expires sysctl
+    - selftest: net: Test IPv4 PMTU exceptions with DSCP and ECN
+    - net: ipv4: Cache pmtu for all packet paths if multipath enabled
+    - neighbour: delete redundant judgment statements
+    - drm/tidss: Fix issue in irq handling causing irq-flood issue
+    - drm/tidss: Clear the interrupt status for interrupts being disabled
+    - kdb: Do not assume write() callback available
+    - alpha: replace hardcoded stack offsets with autogenerated ones
+    - nilfs2: do not output warnings when clearing dirty buffers
+    - can: ems_pci: move ASIX AX99100 ids to pci_ids.h
+    - serial: 8250_pci: add support for ASIX AX99100
+    - parport_pc: add support for ASIX AX99100
+    - netdevsim: print human readable IP address
+    - selftests: rtnetlink: update netdevsim ipsec output format
+    - ARM: dts: dra7: Add bus_dma_limit for l4 cfg bus
+    - x86/i8253: Disable PIT timer 0 when not in use
+    - Revert "btrfs: avoid monopolizing a core when activating a swap file"
+    - btrfs: avoid monopolizing a core when activating a swap file
+    - arm64: mte: Do not allow PROT_MTE on MAP_HUGETLB user mappings
+    - crypto: testmgr - fix wrong key length for pkcs1pad
+    - crypto: testmgr - Fix wrong test case of RSA
+    - crypto: testmgr - fix version number of RSA tests
+    - crypto: testmgr - populate RSA CRT parameters in RSA test vectors
+    - crypto: testmgr - some more fixes to RSA test vectors
+    - mm: update mark_victim tracepoints fields
+    - drm/probe-helper: Create a HPD IRQ event helper for a single connector
+    - drm/rockchip: cdn-dp: Use drm_connector_helper_hpd_irq_event()
+    - ASoC: renesas: rz-ssi: Add a check for negative sample_space
+    - arm64: dts: mediatek: mt8183: Disable DSI display output by default
+    - tpm: Use managed allocation for bios event log
+    - kfence: allow use of a deferrable timer
+    - [Config] updateconfigs to disable new KFENCE_DEFERRABLE
+    - kfence: enable check kfence canary on panic via boot param
+    - kfence: skip __GFP_THISNODE allocations on NUMA systems
+    - soc: mediatek: mtk-devapc: Switch to devm_clk_get_enabled()
+    - soc: mediatek: mtk-devapc: Fix leaking IO map on error paths
+    - soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
+    - soc: mediatek: mtk-devapc: Fix leaking IO map on driver remove
+    - media: uvcvideo: Set error_idx during ctrl_commit errors
+    - media: uvcvideo: Refactor iterators
+    - media: uvcvideo: Only save async fh if success
+    - batman-adv: Drop initialization of flexible ethtool_link_ksettings
+    - usb: dwc3: Increase DWC3 controller halt timeout
+    - usb: dwc3: Fix timeout issue during controller enter/exit from halt state
+    - powerpc/64s/mm: Move __real_pte stubs into hash-4k.h
+    - powerpc/64s: Rewrite __real_pte() and __rpte_to_hidx() as static inline
+    - ALSA: hda/realtek: Fixup ALC225 depop procedure
+    - geneve: Suppress list corruption splat in geneve_destroy_tunnels().
+    - net: extract port range fields from fl_flow_key
+    - flow_dissector: Fix handling of mixed port and port-range keys
+    - flow_dissector: Fix port range key handling in BPF conversion
+    - net: Add non-RCU dev_getbyhwaddr() helper
+    - arp: switch to dev_getbyhwaddr() in arp_req_set_public()
+    - power: supply: da9150-fg: fix potential overflow
+    - nvme/ioctl: add missing space in err message
+    - bpf: skip non exist keys in generic_map_lookup_batch
+    - ALSA: hda/conexant: Add quirk for HP ProBook 450 G4 mute LED
+    - acct: block access to kernel internal filesystems
+    - mtd: rawnand: cadence: fix error code in cadence_nand_init()
+    - mtd: rawnand: cadence: use dma_map_resource for sdma address
+    - mtd: rawnand: cadence: fix incorrect device in dma_unmap_single
+    - x86/cpu/kvm: SRSO: Fix possible missing IBPB on VM-Exit
+    - IB/mlx5: Set and get correct qp_num for a DCT QP
+    - ovl: use wrappers to all vfs_*xattr() calls
+    - ovl: pass ofs to creation operations
+    - scsi: core: Don't memset() the entire scsi_cmnd in scsi_init_command()
+    - scsi: core: Clear driver private data when retrying request
+    - RDMA/mlx5: Fix bind QP error cleanup flow
+    - sunrpc: suppress warnings for unused procfs functions
+    - ALSA: usb-audio: Avoid dropping MIDI events at closing multiple ports
+    - Bluetooth: L2CAP: Fix L2CAP_ECRED_CONN_RSP response
+    - afs: remove variable nr_servers
+    - afs: Make it possible to find the volumes that are using a server
+    - afs: Fix the server_list to unuse a displaced server rather than putting it
+    - net: loopback: Avoid sending IP packets without an Ethernet header
+    - net: cadence: macb: Synchronize stats calculations
+    - ASoC: es8328: fix route from DAC to output
+    - ipvs: Always clear ipvs_property flag in skb_scrub_packet()
+    - tcp: Defer ts_recent changes until req is owned
+    - net: mvpp2: cls: Fixed Non IP flow, with vlan tag flow defination.
+    - net/mlx5: IRQ, Fix null string in debug print
+    - seg6: add support for SRv6 H.Encaps.Red behavior
+    - seg6: add support for SRv6 H.L2Encaps.Red behavior
+    - include: net: add static inline dst_dev_overhead() to dst.h
+    - net: ipv6: seg6_iptunnel: mitigate 2-realloc issue
+    - net: ipv6: fix dst ref loop on input in seg6 lwt
+    - net: ipv6: rpl_iptunnel: mitigate 2-realloc issue
+    - net: ipv6: fix dst ref loop on input in rpl lwt
+    - x86/CPU: Fix warm boot hang regression on AMD SC1100 SoC systems
+    - ftrace: Avoid potential division by zero in function_stat_show()
+    - ALSA: usb-audio: Re-add sample rate quirk for Pioneer DJM-900NXS2
+    - perf/core: Fix low freq setting via IOC_PERIOD
+    - drm/amd/display: Fix HPD after gpu reset
+    - net: enetc: fix the off-by-one issue in enetc_map_tx_buffs()
+    - net: enetc: update UDP checksum when updating originTimestamp field
+    - net: enetc: correct the xdp_tx statistics
+    - phy: tegra: xusb: reset VBUS & ID OVERRIDE
+    - phy: exynos5-usbdrd: fix MPLL_MULTIPLIER and SSC_REFCLKSEL masks in refclk
+    - vmlinux.lds: Ensure that const vars with relocations are mapped R/O
+    - intel_idle: Handle older CPUs, which stop the TSC in deeper C states,
+      correctly
+    - drm/amdgpu: Check extended configuration space register when system uses
+      large bar
+    - drm/amdgpu: disable BAR resize on Dell G5 SE
+    - Revert "of: reserved-memory: Fix using wrong number of cells to get property
+      'alignment'"
+    - HID: appleir: Fix potential NULL dereference at raw event handle
+    - gpio: rcar: Use raw_spinlock to protect register access
+    - gpio: aggregator: protect driver attr handlers against module unload
+    - ALSA: hda: intel: Add Dell ALC3271 to power_save denylist
+    - ALSA: hda/realtek: update ALC222 depop optimize
+    - drm/radeon: Fix rs400_gpu_init for ATI mobility radeon Xpress 200M
+    - platform/x86: thinkpad_acpi: Add battery quirk for ThinkPad X131e
+    - x86/cacheinfo: Validate CPUID leaf 0x2 EDX output
+    - x86/cpu: Validate CPUID leaf 0x2 EDX output
+    - x86/cpu: Properly parse CPUID leaf 0x2 TLB descriptor 0x63
+    - wifi: cfg80211: regulatory: improve invalid hints checking
+    - wifi: nl80211: reject cooked mode if it is set along with other flags
+    - rapidio: add check for rio_add_net() in rio_scan_alloc_net()
+    - rapidio: fix an API misues when rio_add_net() fails
+    - s390/traps: Fix test_monitor_call() inline assembly
+    - block: fix conversion of GPT partition name to 7-bit
+    - mm/page_alloc: fix uninitialized variable
+    - mm: don't skip arch_sync_kernel_mappings() in error paths
+    - wifi: iwlwifi: limit printed string from FW file
+    - HID: google: fix unused variable warning under !CONFIG_ACPI
+    - HID: intel-ish-hid: Fix use-after-free issue in ishtp_hid_remove()
+    - nvmet-tcp: Fix a possible sporadic response drops in weakly ordered arch
+    - net: gso: fix ownership in __udp_gso_segment
+    - caif_virtio: fix wrong pointer check in cfv_probe()
+    - hwmon: (pmbus) Initialise page count in pmbus_identify()
+    - hwmon: (ntc_thermistor) Fix the ncpXXxh103 sensor table
+    - hwmon: (ad7314) Validate leading zero bits and return error
+    - ALSA: usx2y: validate nrpacks module parameter on probe
+    - llc: do not use skb_get() before dev_queue_xmit()
+    - hwmon: fix a NULL vs IS_ERR_OR_NULL() check in xgene_hwmon_probe()
+    - drm/sched: Fix preprocessor guard
+    - be2net: fix sleeping while atomic bugs in be_ndo_bridge_getlink
+    - net: hns3: make sure ptp clock is unregister and freed if
+      hclge_ptp_get_cycle returns an error
+    - ppp: Fix KMSAN uninit-value warning with bpf
+    - vlan: enforce underlying device type
+    - x86/sgx: Support loading enclave page without VMA permissions check
+    - x86/sgx: Move PTE zap code to new sgx_zap_enclave_ptes()
+    - x86/sgx: Export sgx_encl_{grow,shrink}()
+    - x86/sgx: Support VA page allocation without reclaiming
+    - x86/sgx: Fix size overflows in sgx_encl_create()
+    - exfat: fix soft lockup in exfat_clear_bitmap
+    - net-timestamp: support TCP GSO case for a few missing flags
+    - sched/fair: Fix potential memory corruption in child_cfs_rq_on_list
+    - net: ipv6: fix dst ref loop in ila lwtunnel
+    - net: ipv6: fix missing dst ref drop in ila lwtunnel
+    - gpio: rcar: Fix missing of_node_put() call
+    - Revert "drivers/card_reader/rtsx_usb: Restore interrupt based detection"
+    - usb: renesas_usbhs: Call clk_put()
+    - usb: renesas_usbhs: Use devm_usb_get_phy()
+    - usb: hub: lack of clearing xHC resources
+    - usb: quirks: Add DELAY_INIT and NO_LPM for Prolific Mass Storage Card Reader
+    - usb: renesas_usbhs: Flush the notify_hotplug_work
+    - usb: atm: cxacru: fix a flaw in existing endpoint checks
+    - usb: dwc3: Set SUSPENDENABLE soon after phy init
+    - usb: dwc3: gadget: Prevent irq storm when TH re-executes
+    - usb: typec: ucsi: increase timeout for PPM reset operations
+    - usb: typec: tcpci_rt1711h: Unmask alert interrupts to fix functionality
+    - usb: gadget: Set self-powered based on MaxPower and bmAttributes
+    - usb: gadget: Fix setting self-powered state on suspend
+    - usb: gadget: Check bmAttributes only if configuration is valid
+    - xhci: pci: Fix indentation in the PCI device ID definitions
+    - usb: xhci: Enable the TRB overfetch quirk on VIA VL805
+    - mei: me: add panther lake P DID
+    - intel_th: pci: Add Arrow Lake support
+    - intel_th: pci: Add Panther Lake-H support
+    - intel_th: pci: Add Panther Lake-P/U support
+    - slimbus: messaging: Free transaction ID in delayed interrupt scenario
+    - bus: mhi: host: pci_generic: Use pci_try_reset_function() to avoid deadlock
+    - eeprom: digsy_mtc: Make GPIO lookup table match the device
+    - drivers: virt: acrn: hsm: Use kzalloc to avoid info leak in pmcmd_ioctl
+    - media: uvcvideo: Avoid invalid memory access
+    - media: uvcvideo: Avoid returning invalid controls
+    - md: select BLOCK_LEGACY_AUTOLOAD
+    - [Config] updateconfigs to select BLOCK_LEGACY_AUTOLOAD
+    - mtd: rawnand: cadence: fix unchecked dereference
+    - spi-mxs: Fix chipselect glitch
+    - nilfs2: move page release outside of nilfs_delete_entry and nilfs_set_link
+    - nilfs2: eliminate staggered calls to kunmap in nilfs_rename
+    - bpf, vsock: Invoke proto::close on close()
+    - kbuild: userprogs: use correct lld when linking through clang
+    - net: ipv6: fix dst refleaks in rpl, seg6 and ioam6 lwtunnels
+    - Linux 5.15.179
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21647
+    - sched: sch_cake: add bounds checks to host bulk flow fairness counts
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58002
+    - media: uvcvideo: Remove dangling pointers
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58079
+    - media: uvcvideo: Fix crash during unbind if gpio unit is in use
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21721
+    - nilfs2: handle errors that nilfs_prepare_chunk() may return
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-26982
+    - Squashfs: check the inode number is not the invalid value of zero
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21844
+    - smb: client: Add check for next_buffer in receive_encrypted_standard()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58090
+    - sched/core: Prevent rescheduling when interrupts are disabled
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21875
+    - mptcp: always handle address removal under msk socket lock
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21877
+    - usbnet: gl620a: fix endpoint checking in genelink_bind()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21878
+    - i2c: npcm: disable interrupt enable bit before devm_request_irq
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21887
+    - ovl: fix UAF in ovl_dentry_update_reval by moving dput() in ovl_link_up
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21846
+    - acct: perform last write from workqueue
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21848
+    - nfp: bpf: Add check for nfp_app_ctrl_msg_alloc()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21862
+    - drop_monitor: fix incorrect initialization order
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21871
+    - tee: optee: Fix supplicant wait loop
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21865
+    - gtp: Suppress list corruption splat in gtp_net_exit_batch_rtnl().
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21858
+    - geneve: Fix use-after-free in geneve_find_dev().
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21866
+    - powerpc/code-patching: Fix KASAN hit by not flagging text patching area as
+      VM_ALLOC
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21859
+    - USB: gadget: f_midi: f_midi_complete to call queue_work
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21823
+    - batman-adv: Drop unmanaged ELP metric worker
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58005
+    - tpm: Change to kvalloc() in eventlog/acpi.c
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21748
+    - ksmbd: fix integer overflows on 32 bit systems
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57977
+    - memcg: fix soft lockup in the OOM process
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57978
+    - media: imx-jpeg: Fix potential error pointer dereference in detach_pm()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57979
+    - pps: Fix a use-after-free
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-47726
+    - f2fs: fix to wait dio completion
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21811
+    - nilfs2: protect access to buffers with no active references
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21722
+    - nilfs2: do not force clear folio if buffer is referenced
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58086
+    - drm/v3d: Stop active perfmon if it is being destroyed
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21758
+    - ipv6: mcast: add RCU protection to mld_newpack()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21760
+    - ndisc: extend RCU protection in ndisc_send_skb()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21761
+    - openvswitch: use RCU protection in ovs_vport_cmd_fill_info()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21762
+    - arp: use RCU protection in arp_xmit()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21763
+    - neighbour: use RCU protection in __neigh_notify()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21764
+    - ndisc: use RCU protection in ndisc_alloc_skb()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21765
+    - ipv6: use RCU protection in ip6_default_advmss()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21766
+    - ipv4: use RCU protection in __ip_rt_update_pmtu()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21767
+    - clocksource: Use migrate_disable() to avoid calling get_random_u32() in
+      atomic context
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21772
+    - partitions: mac: fix handling of bogus partition table
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21704
+    - usb: cdc-acm: Check control transfer buffer size before access
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21776
+    - USB: hub: Ignore non-compliant devices with too many configs or interfaces
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21835
+    - usb: gadget: f_midi: fix MIDI Streaming descriptor lengths
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21779
+    - KVM: x86: Reject Hyper-V's SEND_IPI hypercalls if local APIC isn't in-kernel
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21781
+    - batman-adv: fix panic during interface removal
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21782
+    - orangefs: fix a oob in orangefs_debug_write
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57834
+    - media: vidtv: Fix a null-ptr-deref in vidtv_mux_stop_thread
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21785
+    - arm64: cacheinfo: Avoid out-of-bounds write to cacheinfo array
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21787
+    - team: better TEAM_OPTION_TYPE_STRING validation
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21791
+    - vrf: use RCU protection in l3mdev_l3_out()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58020
+    - HID: multitouch: Add NULL check in mt_input_configured
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21795
+    - NFSD: fix hang in nfsd4_shutdown_callback
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21796
+    - nfsd: clear acl_access/acl_default after releasing them
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21820
+    - tty: xilinx_uartps: split sysrq handling
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21814
+    - ptp: Ensure info->enable callback is always set
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21735
+    - NFC: nci: Add bounds checking in nci_hci_create_pipe()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21736
+    - nilfs2: fix possible int overflows in nilfs_fiemap()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58001
+    - ocfs2: handle a symlink read error correctly
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58007
+    - soc: qcom: socinfo: Avoid out of bounds read of serial number
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21744
+    - wifi: brcmfmac: fix NULL pointer dereference in brcmf_txfinalize()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21745
+    - blk-cgroup: Fix class @block_class's subsystem refcount leakage
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58076
+    - clk: qcom: gcc-sm6350: Add missing parent_map for two clocks
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58083
+    - KVM: Explicitly verify target vCPU is online in kvm_get_vcpu()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58010
+    - binfmt_flat: Fix integer overflow bug on 32 bit systems
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21749
+    - net: rose: lock the socket in rose_bind()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57981
+    - usb: xhci: Fix NULL pointer dereference on certain command aborts
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21684
+    - gpio: xilinx: Convert gpio_lock to raw spinlock
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58085
+    - tomoyo: don't emit warning in tomoyo_write_control()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58014
+    - wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58016
+    - safesetid: check size of policy writes
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58017
+    - printk: Fix signed integer overflow when defining LOG_BUF_LEN_MAX
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21753
+    - btrfs: fix use-after-free when attempting to join an aborted transaction
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58055
+    - usb: gadget: f_tcm: Don't free command immediately
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57980
+    - media: uvcvideo: Fix double free in error path
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21707
+    - mptcp: consolidate suboption status
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21708
+    - net: usb: rtl8150: enable basic endpoint checking
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21826
+    - netfilter: nf_tables: reject mismatching sum of field_len with set key
+      length
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21715
+    - net: davicom: fix UAF in dm9000_drv_remove
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21718
+    - net: rose: fix timer races against user threads
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21719
+    - ipmr: do not call mr_mfc_uses_dev() for unres entries
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21802
+    - net: hns3: fix oops when unload drivers paralleling
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58058
+    - ubifs: skip dumping tnc tree when zroot is null
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58069
+    - rtc: pcf85063: fix potential OOB write in PCF85063 NVMEM read
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21804
+    - PCI: rcar-ep: Fix incorrect variable used when calling
+      devm_request_mem_region()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58034
+    - memory: tegra20-emc: fix an OF node reference bug in
+      tegra_emc_find_node_by_ram_code()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57973
+    - rdma/cxgb4: Prevent potential integer overflow on 32bit
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21726
+    - padata: avoid UAF for reorder_work
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21727
+    - padata: fix UAF in padata_reorder
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21728
+    - bpf: Send signals asynchronously if !preemptible
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21711
+    - net/rose: prevent integer overflows in rose_setsockopt()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21799
+    - net: ethernet: ti: am65-cpsw: fix freeing IRQ in
+      am65_cpsw_nuss_remove_tx_chns()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21806
+    - net: let net.core.dev_weight always be non-zero
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21830
+    - landlock: Handle weird files
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58071
+    - team: prevent adding a device which is already a team device lower
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58063
+    - wifi: rtlwifi: fix memory leaks and invalid access at probe error path
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58072
+    - wifi: rtlwifi: remove unused check_buddy_priv
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58051
+    - ipmi: ipmb: Add check devm_kasprintf() returned value
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58052
+    - drm/amdgpu: Fix potential NULL pointer dereference in
+      atomctrl_get_smc_sclk_range_table
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57986
+    - HID: core: Fix assumption that Resolution Multipliers must be in Logical
+      Collections
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21731
+    - nbd: don't allow reconnect after disconnect
+  * Fix bugs preventing boot on Intel TDX-enabled hosts (LP: #2097811)
+    - x86/mtrr: Remove physical address size calculation
+  * Build failure when CONFIG_NET_SWITCHDEV=n due to CVE-2024-26837 fix backport
+    (LP: #2104380)
+    - SAUCE: net: switchdev: fix compilation error for CONFIG_NET_SWITCHDEV=n
+  * nfsd hangs and never recovers after NFS4ERR_DELAY and a connection loss
+    (LP: #2103564)
+    - NFSD: Reset cb_seq_status after NFS4ERR_DELAY
+  * kernel hard lockup in cgroups during eBPF workload (LP: #2089318)
+    - cgroup: cgroup: Honor caller's cgroup NS when resolving cgroup id
+    - cgroup: Homogenize cgroup_get_from_id() return value
+    - cgroup: Make cgroup_get_from_id() prettier
+    - cgroup.c: add helper __cset_cgroup_from_root to cleanup duplicated codes
+    - cgroup: Reorganize css_set_lock and kernfs path processing
+  * CVE-2023-52664
+    - net: atlantic: eliminate double free in error handling logic
+  * CVE-2023-52927
+    - netfilter: allow exp not to be removed in nf_ct_find_expectation
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 25 Apr 2025 18:27:55 +0800
+
+linux-xilinx-zynqmp (5.15.0-1046.50) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1046.50 -proposed tracker (LP: #2102584)
+
+  [ Ubuntu: 5.15.0-138.148 ]
+
+  * jammy/linux: 5.15.0-138.148 -proposed tracker (LP: #2102587)
+  * ipsec_offload in rtnetlink.sh from ubunsu_kselftests_net fails on O/J
+    (LP: #2096976)
+    - SAUCE: selftest: netfilter: fix null IP field in kci_test_ipsec_offload
+  * CVE-2025-21756
+    - vsock: Keep the binding until socket destruction
+    - vsock: Orphan socket after transport release
+  * CVE-2024-50256
+    - netfilter: nf_reject_ipv6: fix potential crash in nf_send_reset6()
+  * CVE-2025-21702
+    - pfifo_tail_enqueue: Drop new packet when sch->limit == 0
+  * CVE-2025-21703
+    - netem: Update sch->q.qlen before qdisc_tree_reduce_backlog()
+  * CVE-2025-21700
+    - net: sched: Disallow replacing of child qdisc from one parent to another
+  * CVE-2024-46826
+    - ELF: fix kernel.randomize_va_space double read
+  * CVE-2024-56651
+    - can: hi311x: hi3110_can_ist(): fix potential use-after-free
+  * iBFT iSCSI out-of-bounds shift UBSAN warning (LP: #2097824)
+    - iscsi_ibft: Fix UBSAN shift-out-of-bounds warning in ibft_attr_show_nic()
+  * CVE-2024-50248
+    - ntfs3: Add bounds checking to mi_enum_attr()
+    - fs/ntfs3: Sequential field availability check in mi_enum_attr()
+  * CVE-2022-0995
+    - watch_queue: Use the bitmap API when applicable
+  * CVE-2024-26837
+    - net: bridge: switchdev: Skip MDB replays of deferred events on offload
+  * CVE-2025-21701
+    - net: avoid race between device unregistration and ethnl ops
+  * CVE-2024-57798
+    - drm/dp_mst: Skip CSN if topology probing is not done yet
+    - drm/dp_mst: Ensure mst_primary pointer is valid in
+      drm_dp_mst_handle_up_req()
+  * CVE-2024-56658
+    - net: defer final 'struct net' free in netns dismantle
+  * CVE-2024-35864
+    - smb: client: fix potential UAF in smb2_is_valid_lease_break()
+  * CVE-2024-35864/CVE-2024-26928
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Thu, 27 Mar 2025 15:13:26 +0800
+
+linux-xilinx-zynqmp (5.15.0-1045.49) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1045.49 -proposed tracker (LP: #2102426)
+
+  [ Ubuntu: 5.15.0-136.147 ]
+
+  * jammy/linux: 5.15.0-136.147 -proposed tracker (LP: #2102429)
+  * CVE-2024-57798
+    - drm/dp_mst: Skip CSN if topology probing is not done yet
+    - drm/dp_mst: Ensure mst_primary pointer is valid in
+      drm_dp_mst_handle_up_req()
+  * CVE-2024-56658
+    - net: defer final 'struct net' free in netns dismantle
+  * CVE-2024-35864
+    - smb: client: fix potential UAF in smb2_is_valid_lease_break()
+  * CVE-2024-35864/CVE-2024-26928
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Wed, 19 Mar 2025 15:34:32 +0800
+
+linux-xilinx-zynqmp (5.15.0-1044.48) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1044.48 -proposed tracker (LP: #2098297)
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283)
+    - [Config] Set CONFIG_ARM_TIMER_SP804 as 'n'
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.zynqmp/dkms-versions -- update from kernel-versions
+      (main/2025.02.10)
+
+  [ Ubuntu: 5.15.0-135.146 ]
+
+  * jammy/linux: 5.15.0-135.146 -proposed tracker (LP: #2098300)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.02.10)
+  * Jammy update: v5.15.178 upstream stable release (LP: #2098441)
+    - ASoC: wm8994: Add depends on MFD core
+    - ASoC: samsung: Add missing selects for MFD_WM8994
+    - seccomp: Stub for !CONFIG_SECCOMP
+    - scsi: iscsi: Fix redundant response for ISCSI_UEVENT_GET_HOST_STATS request
+    - irqchip/sunxi-nmi: Add missing SKIP_WAKE flag
+    - ASoC: samsung: Add missing depends on I2C
+    - regmap: detach regmap from dev on regmap_exit
+    - mptcp: don't always assume copied data in mptcp_cleanup_rbuf()
+    - gfs2: Truncate address space when flipping GFS2_DIF_JDATA flag
+    - net: sched: fix ets qdisc OOB Indexing
+    - vfio/platform: check the bounds of read/write syscalls
+    - fs/ntfs3: Additional check in ntfs_file_release
+    - platform/chrome: cros_ec_typec: Check for EC driver
+    - ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_find()
+    - scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
+    - wifi: iwlwifi: add a few rate index validity checks
+    - USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
+    - ALSA: usb-audio: Add delay quirk for USB Audio Device
+    - Input: atkbd - map F23 key to support default copilot shortcut
+    - Input: xpad - add unofficial Xbox 360 wireless receiver clone
+    - Input: xpad - add support for wooting two he (arm)
+    - drm/v3d: Assign job pointer to NULL before signaling the fence
+    - Linux 5.15.178
+  * CVE-2024-49925
+    - fbdev: efifb: Register sysfs groups through driver core
+  * Jammy update: v5.15.177 upstream stable release (LP: #2097298)
+    - ceph: give up on paths longer than PATH_MAX
+    - jbd2: flush filesystem device before updating tail sequence
+    - dm array: fix releasing a faulty array block twice in dm_array_cursor_end
+    - dm array: fix unreleased btree blocks on closing a faulty array cursor
+    - dm array: fix cursor index when skipping across block boundaries
+    - exfat: fix the infinite loop in exfat_readdir()
+    - exfat: fix the infinite loop in __exfat_free_cluster()
+    - ASoC: mediatek: disable buffer pre-allocation
+    - ieee802154: ca8210: Add missing check for kfifo_alloc() in ca8210_probe()
+    - net: 802: LLC+SNAP OID:PID lookup on start of skb data
+    - tcp/dccp: complete lockless accesses to sk->sk_max_ack_backlog
+    - tcp/dccp: allow a connection when sk_max_ack_backlog is zero
+    - net_sched: cls_flow: validate TCA_FLOW_RSHIFT attribute
+    - bnxt_en: Fix possible memory leak when hwrm_req_replace fails
+    - cxgb4: Avoid removal of uninserted tid
+    - tls: Fix tls_sw_sendmsg error handling
+    - netfilter: nf_tables: imbalance in flowtable binding
+    - netfilter: conntrack: clamp maximum hashtable size to INT_MAX
+    - drm/mediatek: Add support for 180-degree rotation in the display driver
+    - ksmbd: fix a missing return value check bug
+    - afs: Fix the maximum cell name length
+    - dm thin: make get_first_thin use rcu-safe list first function
+    - dm-ebs: don't set the flag DM_TARGET_PASSES_INTEGRITY
+    - sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy
+    - sctp: sysctl: rto_min/max: avoid using current->nsproxy
+    - sctp: sysctl: auth_enable: avoid using current->nsproxy
+    - sctp: sysctl: udp_port: avoid using current->nsproxy
+    - sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy
+    - drm/amd/display: Add check for granularity in dml ceil/floor helpers
+    - riscv: Fix sleeping in invalid context in die()
+    - ACPI: resource: Add TongFang GM5HG0A to irq1_edge_low_force_override[]
+    - ACPI: resource: Add Asus Vivobook X1504VAP to irq1_level_low_skip_override[]
+    - drm/amd/display: increase MAX_SURFACES to the value supported by hw
+    - scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
+    - USB: serial: option: add MeiG Smart SRM815
+    - USB: serial: option: add Neoway N723-EA support
+    - staging: iio: ad9834: Correct phase range check
+    - staging: iio: ad9832: Correct phase range check
+    - usb-storage: Add max sectors quirk for Nokia 208
+    - USB: serial: cp210x: add Phoenix Contact UPS Device
+    - usb: dwc3: gadget: fix writing NYET threshold
+    - topology: Keep the cpumask unchanged when printing cpumap
+    - USB: usblp: return error when setting unsupported protocol
+    - USB: core: Disable LPM only for non-suspended ports
+    - usb: fix reference leak in usb_new_device()
+    - usb: gadget: f_uac2: Fix incorrect setting of bNumEndpoints
+    - usb: gadget: f_fs: Remove WARN_ON in functionfs_bind
+    - iio: pressure: zpa2326: fix information leak in triggered buffer
+    - iio: dummy: iio_simply_dummy_buffer: fix information leak in triggered
+      buffer
+    - iio: light: vcnl4035: fix information leak in triggered buffer
+    - iio: imu: kmx61: fix information leak in triggered buffer
+    - iio: adc: ti-ads8688: fix information leak in triggered buffer
+    - iio: gyro: fxas21002c: Fix missing data update in trigger handler
+    - iio: adc: ti-ads124s08: Use gpiod_set_value_cansleep()
+    - iio: adc: at91: call input_free_device() on allocated iio_dev
+    - iio: inkern: call iio_device_put() only on mapped devices
+    - iio: adc: ad7124: Disable all channels at probe time
+    - block, bfq: fix waker_bfqq UAF after bfq_split_bfqq()
+    - arm64: dts: rockchip: add hevc power domain clock to rk3328
+    - of: unittest: Add bus address range parsing tests
+    - of/address: Add support for 3 address cell bus
+    - of: address: Fix address translation when address-size is greater than 2
+    - of: address: Remove duplicated functions
+    - of: address: Store number of bus flag cells rather than bool
+    - of: address: Preserve the flags portion on 1:1 dma-ranges mapping
+    - phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers
+    - phy: usb: Toggle the PHY power during init
+    - ocfs2: correct return value of ocfs2_local_free_info()
+    - ocfs2: fix slab-use-after-free due to dangling pointer dqi_priv
+    - mptcp: drop port parameter of mptcp_pm_add_addr_signal
+    - mptcp: fix TCP options overflow.
+    - phy: usb: Use slow clock for wake enabled suspend
+    - phy: usb: Fix clock imbalance for suspend/resume
+    - net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()
+    - bpf: Fix bpf_sk_select_reuseport() memory leak
+    - pktgen: Avoid out-of-bounds access in get_imix_entries
+    - net: add exit_batch_rtnl() method
+    - gtp: use exit_batch_rtnl() method
+    - gtp: Use for_each_netdev_rcu() in gtp_genl_dump_pdp().
+    - gtp: Destroy device along with udp socket's netns dismantle.
+    - nfp: bpf: prevent integer overflow in nfp_bpf_event_output()
+    - net: xilinx: axienet: Fix IRQ coalescing packet count overflow
+    - net/mlx5: Add priorities for counters in RDMA namespaces
+    - net/mlx5: Refactor mlx5_get_flow_namespace
+    - net/mlx5: Fix RDMA TX steering prio
+    - drm/v3d: Ensure job pointer is set to NULL after job completion
+    - Revert "mtd: spi-nor: core: replace dummy buswidth from addr to data"
+    - i2c: mux: demux-pinctrl: check initial mux selection, too
+    - i2c: rcar: fix NACK handling when being a target
+    - mac802154: check local interfaces before deleting sdata list
+    - hfs: Sanity check the root record
+    - fs: fix missing declaration of init_files
+    - kheaders: Ignore silly-rename files
+    - ACPI: resource: acpi_dev_irq_override(): Check DMI match last
+    - poll_wait: add mb() to fix theoretical race between waitqueue_active() and
+      .poll()
+    - nvmet: propagate npwg topology
+    - net: ethernet: xgbe: re-add aneg to supported features in PHY quirks
+    - vsock/virtio: cancel close work in the destructor
+    - vsock: reset socket state when de-assigning the transport
+    - vsock: prevent null-ptr-deref in vsock_*[has_data|has_space]
+    - filemap: avoid truncating 64-bit offset to 32 bits
+    - fs/proc: fix softlockup in __read_vmcore (part 2)
+    - gpiolib: cdev: Fix use after free in lineinfo_changed_notify
+    - irqchip/gic-v3: Handle CPU_PM_ENTER_FAILED correctly
+    - hrtimers: Handle CPU state correctly on hotplug
+    - drm/i915/fb: Relax clear color alignment to 64 bytes
+    - iio: imu: inv_icm42600: fix spi burst write not supported
+    - iio: imu: inv_icm42600: fix timestamps after suspend if sensor is on
+    - iio: adc: rockchip_saradc: fix information leak in triggered buffer
+    - Revert "drm/amdgpu: rework resume handling for display (v2)"
+    - Revert "regmap: detach regmap from dev on regmap_exit"
+    - vsock/virtio: discard packets if the transport changes
+    - ipv6: avoid possible NULL deref in rt6_uncached_list_flush_dev()
+    - nfsd: add list_head nf_gc to struct nfsd_file
+    - x86/xen: fix SLS mitigation in xen_hypercall_iret()
+    - scsi: sg: Fix slab-use-after-free read in sg_release()
+    - net: fix data-races around sk->sk_forward_alloc
+    - xhci: use pm_ptr() instead of #ifdef for CONFIG_PM conditionals
+    - Partial revert of xhci: use pm_ptr() instead #ifdef for CONFIG_PM
+      conditionals
+    - Linux 5.15.177
+  * CVE-2024-46784
+    - net: mana: Fix error handling in mana_create_txq/rxq's NAPI cleanup
+  * CVE-2024-44938
+    - jfs: Fix shift-out-of-bounds in dbDiscardAG
+  * CVE-2024-43900
+    - media: xc2028: avoid use-after-free in load_firmware_cb()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327)
+    - ALSA: usb: Fix UBSAN warning in parse_audio_unit()
+    - usb: cdns3: Add quirk flag to enable suspend residency
+    - ASoC: Intel: sof_sdw: fix jack detection on ADL-N variant RVP
+    - PCI: vmd: Create domain symlink before pci_bus_add_devices()
+    - PCI: Add ACS quirk for Broadcom BCM5760X NIC
+    - MIPS: Loongson64: DTS: Fix msi node for ls7a
+    - usb: dwc2: gadget: Don't write invalid mapped sg entries into dma_desc with
+      iommu enabled
+    - i2c: pnx: Fix timeout in wait functions
+    - erofs: fix incorrect symlink detection in fast symlink
+    - net/smc: check sndbuf_space again after NOSPACE flag is set in smc_poll
+    - ionic: use ee->offset when returning sprom data
+    - net: hinic: Fix cleanup in create_rxqs/txqs()
+    - net: ethernet: bgmac-platform: fix an OF node reference leak
+    - netfilter: ipset: Fix for recursive locking warning
+    - net: mdiobus: fix an OF node reference leak
+    - mmc: sdhci-tegra: Remove SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC quirk
+    - chelsio/chtls: prevent potential integer overflow on 32bit
+    - i2c: riic: Always round-up when calculating bus period
+    - efivarfs: Fix error on non-existent file
+    - USB: serial: option: add TCL IK512 MBIM & ECM
+    - USB: serial: option: add MeiG Smart SLM770A
+    - USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
+    - USB: serial: option: add MediaTek T7XX compositions
+    - USB: serial: option: add Telit FE910C04 rmnet compositions
+    - hwmon: (tmp513) Don't use "proxy" headers
+    - hwmon: (tmp513) Simplify with dev_err_probe()
+    - hwmon: (tmp513) Use SI constants from units.h
+    - hwmon: (tmp513) Fix interpretation of values of Shunt Voltage and Limit
+      Registers
+    - hwmon: (tmp513) Fix Current Register value interpretation
+    - hwmon: (tmp513) Fix interpretation of values of Temperature Result and Limit
+      Registers
+    - hwmon: (tmp513) Fix division of negative numbers
+    - sh: clk: Fix clk_enable() to return 0 on NULL clk
+    - zram: refuse to use zero sized block device as backing device
+    - btrfs: tree-checker: reject inline extent items with 0 ref count
+    - tracing: Fix test_event_printk() to process entire print argument
+    - tracing: Add missing helper functions in event pointer dereference check
+    - tracing: Add "%s" check in test_event_printk()
+    - NFS/pnfs: Fix a live lock between recalled layouts and layoutget
+    - of/irq: Fix using uninitialized variable @addr_len in API of_irq_parse_one()
+    - udmabuf: also check for F_SEAL_FUTURE_WRITE
+    - of: Fix error path in of_parse_phandle_with_args_map()
+    - of: Fix refcount leakage for OF node returned by __of_get_dma_parent()
+    - ceph: validate snapdirname option length when mounting
+    - epoll: Add synchronous wakeup support for ep_poll_callback
+    - drm/amdgpu: Handle NULL bo->tbo.resource (again) in amdgpu_vm_bo_update
+    - mm/vmstat: fix a W=1 clang compiler warning
+    - tcp_bpf: Charge receive socket buffer in bpf_tcp_ingress()
+    - tcp_bpf: Add sk_rmem_alloc related logic for tcp_bpf ingress redirection
+    - bpf: Check negative offsets in __bpf_skb_min_len()
+    - nfsd: restore callback functionality for NFSv4.0
+    - mtd: diskonchip: Cast an operand to prevent potential overflow
+    - mtd: rawnand: arasan: Fix double assertion of chip-select
+    - mtd: rawnand: arasan: Fix missing de-registration of NAND
+    - phy: core: Fix an OF node refcount leakage in _of_phy_get()
+    - phy: core: Fix an OF node refcount leakage in of_phy_provider_lookup()
+    - phy: core: Fix that API devm_phy_put() fails to release the phy
+    - phy: core: Fix that API devm_of_phy_provider_unregister() fails to
+      unregister the phy provider
+    - phy: core: Fix that API devm_phy_destroy() fails to destroy the phy
+    - dmaengine: mv_xor: fix child node refcount handling in early exit
+    - dmaengine: dw: Select only supported masters for ACPI devices
+    - mtd: rawnand: fix double free in atmel_pmecc_create_user()
+    - tracing/kprobe: Make trace_kprobe's module callback called after jump_label
+      update
+    - watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04
+    - scsi: qla1280: Fix hw revision numbering for ISP1020/1040
+    - ALSA: hda/conexant: fix Z60MR100 startup pop issue
+    - regmap: Use correct format specifier for logging range errors
+    - platform/x86: asus-nb-wmi: Ignore unknown event 0xCF
+    - scsi: mpt3sas: Diag-Reset when Doorbell-In-Use bit is set during driver load
+      time
+    - scsi: storvsc: Do not flag MAINTENANCE_IN return of SRB_STATUS_DATA_OVERRUN
+      as an error
+    - virtio-blk: don't keep queue frozen during system suspend
+    - vmalloc: fix accounting with i915
+    - MIPS: Probe toolchain support of -msym32
+    - arm64: mm: Rename asid2idx() to ctxid2asid()
+    - arm64: Ensure bits ASID[15:8] are masked out when the kernel uses 8-bit
+      ASIDs
+    - drm/dp_mst: Verify request type in the corresponding down message reply
+    - lib: stackinit: hide never-taken branch from compiler
+    - ksmbd: fix racy issue from session lookup and expire
+    - tracing: Constify string literal data member in struct trace_event_call
+    - btrfs: avoid monopolizing a core when activating a swap file
+    - x86/hyperv: Fix hv tsc page based sched_clock for hibernation
+    - selinux: ignore unknown extended permissions
+    - tracing: Have process_string() also allow arrays
+    - thunderbolt: Add support for Intel Raptor Lake
+    - thunderbolt: Add support for Intel Meteor Lake
+    - thunderbolt: Add Intel Barlow Ridge PCI ID
+    - thunderbolt: Add support for Intel Lunar Lake
+    - thunderbolt: Add support for Intel Panther Lake-M/P
+    - xhci: retry Stop Endpoint on buggy NEC controllers
+    - usb: xhci: Limit Stop Endpoint retries
+    - xhci: Turn NEC specific quirk for handling Stop Endpoint errors generic
+    - RDMA/mlx5: Enforce same type port association for multiport RoCE
+    - RDMA/bnxt_re: Add check for path mtu in modify_qp
+    - RDMA/bnxt_re: Fix reporting hw_ver in query_device
+    - RDMA/bnxt_re: Fix max_qp_wrs reported
+    - RDMA/bnxt_re: Fix the locking while accessing the QP table
+    - drm/bridge: adv7511_audio: Update Audio InfoFrame properly
+    - RDMA/hns: Remove redundant 'attr_mask' in modify_qp_init_to_init()
+    - RDMA/hns: Remove redundant 'bt_level' for hem_list_alloc_item()
+    - RDMA/hns: Fix mapping error of zero-hop WQE buffer
+    - RDMA/hns: Fix warning storm caused by invalid input in IO path
+    - RDMA/hns: Fix missing flush CQE for DWQE
+    - net: stmmac: platform: provide devm_stmmac_probe_config_dt()
+    - net: stmmac: don't create a MDIO bus if unnecessary
+    - net: stmmac: restructure the error path of stmmac_probe_config_dt()
+    - drm/i915/dg1: Fix power gate sequence.
+    - net: llc: reset skb->transport_header
+    - ALSA: usb-audio: US16x08: Initialize array before use
+    - eth: bcmsysport: fix call balance of priv->clk handling routines
+    - net: mv643xx_eth: fix an OF node reference leak
+    - net: wwan: iosm: Properly check for valid exec stage in ipc_mmio_init()
+    - btrfs: rename and export __btrfs_cow_block()
+    - btrfs: sysfs: convert scnprintf and snprintf to sysfs_emit
+    - btrfs: sysfs: fix direct super block member reads
+    - wifi: mac80211: wake the queues in case of failure in resume
+    - sound: usb: enable DSD output for ddHiFi TC44C
+    - sound: usb: format: don't warn that raw DSD is unsupported
+    - bpf: fix potential error return
+    - net: usb: qmi_wwan: add Telit FE910C04 compositions
+    - irqchip/gic: Correct declaration of *percpu_base pointer in union gic_base
+    - ARC: build: Try to guess GCC variant of cross compiler
+    - usb: xhci: Avoid queuing redundant Stop Endpoint commands
+    - modpost: fix input MODULE_DEVICE_TABLE() built for 64-bit on 32-bit host
+    - modpost: fix the missed iteration for the max bit in do_input()
+    - kcov: mark in_softirq_really() as __always_inline
+    - sky2: Add device ID 11ab:4373 for Marvell 88E8075
+    - net/sctp: Prevent autoclose integer overflow in sctp_association_init()
+    - drm: adv7511: Drop dsi single lane support
+    - dt-bindings: display: adi,adv7533: Drop single lane support
+    - Linux 5.15.176
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57884
+    - mm: vmscan: account for free pages to prevent infinite Loop in
+      throttle_direct_reclaim()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57889
+    - pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57890
+    - RDMA/uverbs: Prevent integer overflow issue
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57896
+    - btrfs: flush delalloc workers queue before stopping cleaner kthread during
+      unmount
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57897
+    - drm/amdkfd: Correct the migration DMA map direction
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56759
+    - btrfs: fix use-after-free when COWing tree bock and tracing is enabled
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57900
+    - ila: serialize calls to nf_register_net_hooks()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57901
+    - af_packet: fix vlan_get_protocol_dgram() vs MSG_PEEK
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57902
+    - af_packet: fix vlan_get_tci() vs MSG_PEEK
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57903
+    - net: restrict SO_REUSEPORT to inet sockets
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-36476
+    - RDMA/rtrs: Ensure 'ib_sge list' is accessible
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57802
+    - netrom: check buffer length before accessing it
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57841
+    - net: fix memory leak in tcp_conn_request()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-49998
+    - net: dsa: improve shutdown sequence
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-50121
+    - nfsd: cancel nfsd_shrinker_work using sync mode in nfs4_state_shutdown_net
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57792
+    - power: supply: gpio-charger: Fix set charge current limits
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56763
+    - tracing: Prevent bad count for tracing_cpumask_write
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56626
+    - ksmbd: fix Out-of-Bounds Write in ksmbd_vfs_stream_write
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56627
+    - ksmbd: fix Out-of-Bounds Read in ksmbd_vfs_stream_read
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56616
+    - drm/dp_mst: Fix MST sideband message body length check
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-53099
+    - bpf: Check validity of link->type in bpf_link_show_fdinfo()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57807
+    - scsi: megaraid_sas: Fix for a potential deadlock
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56767
+    - dmaengine: at_xdmac: avoid null_prt_deref in at_xdmac_prep_dma_memset
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56769
+    - media: dvb-frontends: dib3000mb: fix uninit-value in dib3000_write_reg
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-53690
+    - nilfs2: prevent use of deleted inode
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-55881
+    - KVM: x86: Play nice with protected guests in complete_hypercall_exit()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-55916
+    - Drivers: hv: util: Avoid accessing a ringbuffer not initialized yet
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56369
+    - drm/modes: Avoid divide by zero harder in drm_mode_vrefresh()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56715
+    - ionic: Fix netdev notifier unregister on failure
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56716
+    - netdevsim: prevent bad user input in nsim_dev_health_break_write()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57791
+    - net/smc: check return value of sock_recvmsg when draining clc data
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-47408
+    - net/smc: check smcd_v2_ext_offset when receiving proposal msg
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-49571
+    - net/smc: check iparea_offset and ipv6_prefixes_cnt when receiving proposal
+      msg
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302)
+    - tcp: check space before adding MPTCP SYN options
+    - ALSA: usb-audio: Add implicit feedback quirk for Yamaha THR5
+    - usb: host: max3421-hcd: Correctly abort a USB request.
+    - ata: sata_highbank: fix OF node reference leak in highbank_initialize_phys()
+    - usb: dwc2: Fix HCD resume
+    - usb: dwc2: hcd: Fix GetPortStatus & SetPortFeature
+    - usb: dwc2: Fix HCD port connection race
+    - usb: ehci-hcd: fix call balance of clocks handling routines
+    - drm/i915: Fix memory leak by correcting cache object name in error handler
+    - xfs: update btree keys correctly when _insrec splits an inode root block
+    - xfs: don't drop errno values when we fail to ficlone the entire range
+    - xfs: return from xfs_symlink_verify early on V4 filesystems
+    - xfs: fix scrub tracepoints when inode-rooted btrees are involved
+    - bpf, sockmap: Fix update element with same
+    - batman-adv: Do not send uninitialized TT changes
+    - batman-adv: Remove uninitialized data in full table TT response
+    - batman-adv: Do not let TT changes list grows indefinitely
+    - tipc: fix NULL deref in cleanup_bearer()
+    - selftests: mlxsw: sharedbuffer: Remove h1 ingress test case
+    - selftests: mlxsw: sharedbuffer: Remove duplicate test cases
+    - ptp: kvm: Use decrypted memory in confidential guest on x86
+    - ptp: kvm: x86: Return EOPNOTSUPP instead of ENODEV from kvm_arch_ptp_init()
+    - net: sparx5: fix FDMA performance issue
+    - net: sparx5: fix the maximum frame length register
+    - ACPI: resource: Fix memory resource type union access
+    - cxgb4: use port number to set mac addr
+    - qca_spi: Fix clock speed for multiple QCA7000
+    - qca_spi: Make driver probing reliable
+    - Documentation: PM: Clarify pm_runtime_resume_and_get() return value
+    - bonding: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL
+    - team: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL
+    - ACPICA: events/evxfregn: don't release the ContextMutex that was never
+      acquired
+    - blk-iocost: Avoid using clamp() on inuse in __propagate_weights()
+    - tracing/kprobes: Skip symbol counting logic for module symbols in
+      create_local_trace_kprobe()
+    - xen/netfront: fix crash when removing device
+    - x86: make get_cpu_vendor() accessible from Xen code
+    - objtool/x86: allow syscall instruction
+    - x86/static-call: provide a way to do very early static-call updates
+    - x86/static-call: Remove early_boot_irqs_disabled check to fix Xen PVH dom0
+    - x86/asm: Make serialize() always_inline
+    - x86/xen: don't do PV iret hypercall through hypercall page
+    - x86/xen: add central hypercall functions
+    - x86/xen: use new hypercall functions instead of hypercall page
+    - x86/xen: remove hypercall page
+    - ALSA: usb-audio: Fix a DMA to stack memory bug
+    - x86/static-call: fix 32-bit build
+    - Linux 5.15.175
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-53125
+    - bpf: sync_linked_regs() must preserve subreg_def
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56770
+    - net/sched: netem: account for backlog updates from child qdisc
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56659
+    - net: lapb: increase LAPB_HEADER_LEN
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56662
+    - acpi: nfit: vmalloc-out-of-bounds Read in acpi_nfit_ctl
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-42315
+    - exfat: fix potential deadlock on __exfat_get_dentry_set
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-53119
+    - virtio/vsock: Fix accept_queue memory leak
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56670
+    - usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to
+      accessing null pointer
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283)
+    - arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
+    - media: venus: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - media: gspca: ov534-ov772x: Fix off-by-one error in set_frame_rate()
+    - media: uvcvideo: Stop stream during unregister
+    - vmstat: call fold_vm_zone_numa_events() before show per zone NUMA event
+    - iommu/io-pgtable-arm: Fix stage-2 map/unmap for concatenated tables
+    - leds: lp55xx: Remove redundant test for invalid channel number
+    - clk: qcom: gcc-qcs404: fix initial rate of GPLL3
+    - samples: pktgen: correct dev to DEV
+    - ARM: 9419/1: mm: Fix kernel memory mapping for xip kernels
+    - x86/mm: Fix a kdump kernel failure on SME system when CONFIG_IMA_KEXEC=y
+    - vdpa/mlx5: Fix PA offset with unaligned starting iotlb map
+    - KVM: nVMX: Treat vpid01 as current if L2 is active, but with VPID disabled
+    - ocfs2: fix UBSAN warning in ocfs2_verify_volume()
+    - drm/bridge: tc358768: Fix DSI command tx
+    - mmc: sunxi-mmc: Add D1 MMC variant
+    - mmc: sunxi-mmc: Fix A100 compatible description
+    - lib/buildid: Fix build ID parsing logic
+    - media: dvbdev: fix the logic when DVB_DYNAMIC_MINORS is not set
+    - NFSD: initialize copy->cp_clp early in nfsd4_copy for use by trace point
+    - NFSD: Async COPY result needs to return a write verifier
+    - NFSD: Initialize struct nfsd4_copy earlier
+    - NFSD: Never decrement pending_async_copies on error
+    - mm: revert "mm: shmem: fix data-race in shmem_getattr()"
+    - mm: avoid unsafe VMA hook invocation when error arises on mmap hook
+    - mm: unconditionally close VMAs on error
+    - mm: refactor arch_calc_vm_flag_bits() and arm64 MTE handling
+    - NFS: nfs_async_write_reschedule_io must not recurse into the writeback code
+    - ASoC: Intel: bytcr_rt5640: Add support for non ACPI instantiated codec
+    - ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet
+    - ASoC: Intel: sst: Support LPE0F28 ACPI HID
+    - wifi: iwlwifi: mvm: Use the sync timepoint API in suspend
+    - mac80211: fix user-power when emulating chanctx
+    - usb: add support for new USB device ID 0x17EF:0x3098 for the r8152 driver
+    - selftests/watchdog-test: Fix system accidentally reset after watchdog-test
+    - ALSA: hda/realtek: Add subwoofer quirk for Infinix ZERO BOOK 13
+    - x86/amd_nb: Fix compile-testing without CONFIG_AMD_NB
+    - net: usb: qmi_wwan: add Quectel RG650V
+    - soc: qcom: Add check devm_kasprintf() returned value
+    - regulator: rk808: Add apply_bit for BUCK3 on RK809
+    - platform/x86: dell-smbios-base: Extends support to Alienware products
+    - platform/x86: dell-wmi-base: Handle META key Lock/Unlock events
+    - can: j1939: fix error in J1939 documentation.
+    - ASoC: stm: Prevent potential division by zero in stm32_sai_mclk_round_rate()
+    - ASoC: stm: Prevent potential division by zero in stm32_sai_get_clk_div()
+    - proc/softirqs: replace seq_printf with seq_put_decimal_ull_width
+    - ALSA: usb-audio: Fix Yamaha P-125 Quirk Entry
+    - ARM: 9420/1: smp: Fix SMP for xip kernels
+    - ipmr: Fix access to mfc_cache_list without lock held
+    - nvme: fix metadata handling in nvme-passthrough
+    - x86/barrier: Do not serialize MSR accesses on AMD
+    - kselftest/arm64: mte: fix printf type warnings about longs
+    - s390/cio: Do not unregister the subchannel based on DNV
+    - brd: remove brd_devices_mutex mutex
+    - mips: asm: fix warning when disabling MIPS_FP_SUPPORT
+    - m68k: mvme147: Fix SCSI controller IRQ numbers
+    - m68k: mvme16x: Add and use "mvme16x.h"
+    - m68k: mvme147: Reinstate early console
+    - arm64: fix .data.rel.ro size assertion when CONFIG_LTO_CLANG
+    - acpi/arm64: Adjust error handling procedure in gtdt_parse_timer_block()
+    - s390/syscalls: Avoid creation of arch/arch/ directory
+    - firmware: google: Unregister driver_info on failure
+    - crypto: qat - remove faulty arbiter config reset
+    - thermal: core: Initialize thermal zones before registering them
+    - EDAC/fsl_ddr: Fix bad bit shift operations
+    - crypto: cavium - Fix the if condition to exit loop after timeout
+    - ACPI: CPPC: Fix _CPC register setting issue
+    - crypto: caam - add error check to caam_rsa_set_priv_key_form
+    - crypto: cavium - Fix an error handling path in cpt_ucode_load_fw()
+    - time: Fix references to _msecs_to_jiffies() handling of values
+    - timekeeping: Consolidate fast timekeeper
+    - seqlock/latch: Provide raw_read_seqcount_latch_retry()
+    - kcsan, seqlock: Support seqcount_latch_t
+    - kcsan, seqlock: Fix incorrect assumption in read_seqbegin()
+    - clocksource/drivers:sp804: Make user selectable
+    - spi: spi-fsl-lpspi: downgrade log level for pio mode
+    - spi: spi-fsl-lpspi: Use IRQF_NO_AUTOEN flag in request_irq()
+    - soc: ti: smartreflex: Use IRQF_NO_AUTOEN flag in request_irq()
+    - mmc: mmc_spi: drop buggy snprintf()
+    - tpm: fix signed/unsigned bug when checking event logs
+    - arm64: dts: mt8183: krane: Fix the address of eeprom at i2c4
+    - arm64: dts: mt8183: kukui: Fix the address of eeprom at i2c4
+    - arm64: dts: mediatek: mt8173-elm-hana: Add vdd-supply to second source
+      trackpad
+    - Revert "cgroup: Fix memory leak caused by missing cgroup_bpf_offline"
+    - cgroup/bpf: only cgroup v2 can be attached by bpf programs
+    - arm64: dts: mt8183: fennel: add i2c2's i2c-scl-internal-delay-ns
+    - arm64: dts: mt8183: burnet: add i2c2's i2c-scl-internal-delay-ns
+    - arm64: dts: mt8183: Damu: add i2c2's i2c-scl-internal-delay-ns
+    - pwm: imx27: Workaround of the pwm output bug when decrease the duty cycle
+    - ARM: dts: cubieboard4: Fix DCDC5 regulator constraints
+    - pmdomain: ti-sci: Add missing of_node_put() for args.np
+    - spi: tegra210-quad: Avoid shift-out-of-bounds
+    - spi: zynqmp-gqspi: Undo runtime PM changes at driver exit time​
+    - regmap: irq: Set lockdep class for hierarchical IRQ domains
+    - arm64: dts: mt8183: jacuzzi: remove unused ddc-i2c-bus
+    - arm64: dts: mt8183: jacuzzi: Move panel under aux-bus
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Fix DP bridge supply names
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add supplies for fixed
+      regulators
+    - selftests/resctrl: Protect against array overrun during iMC config parsing
+    - media: venus: venc: Use pmruntime autosuspend
+    - media: venus: vdec: decoded picture buffer handling during reconfig sequence
+    - media: venus : Addition of EOS Event support for Encoder
+    - media: venus : Addition of support for VIDIOC_TRY_ENCODER_CMD
+    - venus: venc: add handling for VIDIOC_ENCODER_CMD
+    - media: venus: provide ctx queue lock for ioctl synchronization
+    - media: atomisp: remove #ifdef HAS_NO_HMEM
+    - platform/x86: panasonic-laptop: Replace snprintf in show functions with
+      sysfs_emit
+    - platform/x86: panasonic-laptop: Return errno correctly in show callback
+    - drm/mm: Mark drm_mm_interval_tree*() functions with __maybe_unused
+    - drm/omap: Fix possible NULL dereference
+    - drm/omap: Fix locking in omap_gem_new_dmabuf()
+    - wifi: p54: Use IRQF_NO_AUTOEN flag in request_irq()
+    - wifi: mwifiex: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/imx/dcss: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/imx/ipuv3: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/v3d: Address race-condition in MMU flush
+    - wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss1
+    - wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss2
+    - dt-bindings: vendor-prefixes: Add NeoFidelity, Inc
+    - ASoC: fsl_micfil: Drop unnecessary register read
+    - ASoC: fsl_micfil: do not define SHIFT/MASK for single bits
+    - ASoC: fsl_micfil: use GENMASK to define register bit fields
+    - ASoC: fsl_micfil: fix regmap_write_bits usage
+    - ASoC: dt-bindings: mt6359: Update generic node name and dmic-mode
+    - drm/bridge: anx7625: Drop EDID cache on bridge power off
+    - libbpf: Fix output .symtab byte-order during linking
+    - bpf: Fix the xdp_adjust_tail sample prog issue
+    - libbpf: fix sym_is_subprog() logic for weak global subprogs
+    - xfrm: rename xfrm_state_offload struct to allow reuse
+    - xfrm: store and rely on direction to construct offload flags
+    - netdevsim: rely on XFRM state direction instead of flags
+    - netdevsim: copy addresses for both in and out paths
+    - drm/bridge: tc358767: Fix link properties discovery
+    - selftests/bpf: Fix msg_verify_data in test_sockmap
+    - selftests/bpf: Fix txmsg_redir of test_txmsg_pull in test_sockmap
+    - drm: fsl-dcu: enable PIXCLK on LS1021A
+    - drm/panfrost: Remove unused id_mask from struct panfrost_model
+    - drm/msm/adreno: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/etnaviv: Request pages from DMA32 zone on addressing_limited
+    - drm/etnaviv: fix power register offset on GC300
+    - drm/etnaviv: hold GPU lock across perfmon sampling
+    - wifi: wfx: Fix error handling in wfx_core_init()
+    - drm/msm/dpu: cast crtc_clk calculation to u64 in _dpu_core_perf_calc_clk()
+    - netfilter: nf_tables: skip transaction if update object is not implemented
+    - netfilter: nf_tables: must hold rcu read lock while iterating object type
+      list
+    - netlink: typographical error in nlmsg_type constants definition
+    - selftests/bpf: Add txmsg_pass to pull/push/pop in test_sockmap
+    - selftests/bpf: Fix SENDPAGE data logic in test_sockmap
+    - selftests, bpf: Add one test for sockmap with strparser
+    - selftests/bpf: Fix total_bytes in msg_loop_rx in test_sockmap
+    - selftests/bpf: Add push/pop checking for msg_verify_data in test_sockmap
+    - bpf, sockmap: Several fixes to bpf_msg_push_data
+    - bpf, sockmap: Fix sk_msg_reset_curr
+    - selftests: net: really check for bg process completion
+    - drm/amdkfd: Fix wrong usage of INIT_WORK()
+    - net: rfkill: gpio: Add check for clk_enable()
+    - driver core: Introduce device_find_any_child() helper
+    - netpoll: Use rcu_access_pointer() in netpoll_poll_lock
+    - wireguard: selftests: load nf_conntrack if not present
+    - trace/trace_event_perf: remove duplicate samples on the first tracepoint
+      event
+    - pinctrl: zynqmp: drop excess struct member description
+    - powerpc/vdso: Flag VDSO64 entry points as functions
+    - mfd: tps65010: Use IRQF_NO_AUTOEN flag in request_irq() to fix race
+    - mfd: da9052-spi: Change read-mask to write-mask
+    - mfd: intel_soc_pmic_bxtwc: Use dev_err_probe()
+    - cpufreq: loongson2: Unregister platform_driver on failure
+    - mtd: rawnand: atmel: Fix possible memory leak
+    - RDMA/bnxt_re: Check cqe flags to know imm_data vs inv_irkey
+    - clk: imx: lpcg-scu: SW workaround for errata (e10858)
+    - clk: imx: clk-scu: fix clk enable state save and restore
+    - mfd: rt5033: Fix missing regmap_del_irq_chip()
+    - scsi: fusion: Remove unused variable 'rc'
+    - RDMA/hns: Fix out-of-order issue of requester when setting FENCE
+    - powerpc/sstep: make emulate_vsx_load and emulate_vsx_store static
+    - powerpc/kexec: Fix return of uninitialized variable
+    - fbdev/sh7760fb: Alloc DMA memory from hardware device
+    - dt-bindings: clock: axi-clkgen: include AXI clk
+    - clk: clk-axi-clkgen: make sure to enable the AXI bus clock
+    - pinctrl: k210: Undef K210_PC_DEFAULT
+    - mailbox: arm_mhuv2: clean up loop in get_irq_chan_comb()
+    - perf cs-etm: Don't flush when packet_queue fills up
+    - perf probe: Fix libdw memory leak
+    - perf probe: Correct demangled symbols in C++ program
+    - PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
+    - PCI: cpqphp: Fix PCIBIOS_* return value confusion
+    - f2fs: fix the wrong f2fs_bug_on condition in f2fs_do_replace_block
+    - f2fs: remove struct segment_allocation default_salloc_ops
+    - f2fs: open code allocate_segment_by_default
+    - f2fs: remove the unused flush argument to change_curseg
+    - f2fs: check curseg->inited before write_sum_page in change_curseg
+    - perf trace: avoid garbage when not printing a trace event's arguments
+    - m68k: mcfgpio: Fix incorrect register offset for CONFIG_M5441x
+    - m68k: coldfire/device.c: only build FEC when HW macros are defined
+    - perf trace: Do not lose last events in a race
+    - perf trace: Avoid garbage when not printing a syscall's arguments
+    - rpmsg: glink: Add TX_DATA_CONT command while sending
+    - rpmsg: glink: Send READ_NOTIFY command in FIFO full case
+    - rpmsg: glink: Fix GLINK command prefix
+    - rpmsg: glink: use only lower 16-bits of param2 for CMD_OPEN name length
+    - remoteproc: qcom_q6v5_mss: Re-order writes to the IMEM region
+    - NFSD: Cap the number of bytes copied by nfs4_reset_recoverydir()
+    - sunrpc: simplify two-level sysctl registration for svcrdma_parm_table
+    - NFSD: Fix nfsd4_shutdown_copy()
+    - hwmon: (tps23861) Fix reporting of negative temperatures
+    - vdpa/mlx5: Fix suboptimal range on iotlb iteration
+    - selftests/mount_setattr: Fix failures on 64K PAGE_SIZE kernels
+    - fs_parser: update mount_api doc to match function signature
+    - power: supply: core: Remove might_sleep() from power_supply_put()
+    - power: supply: bq27xxx: Fix registers of bq27426
+    - net: usb: lan78xx: Fix memory leak on device unplug by freeing PHY device
+    - tg3: Set coherent DMA mask bits to 31 for BCM57766 chipsets
+    - net: usb: lan78xx: Fix refcounting and autosuspend on invalid WoL
+      configuration
+    - net: mdio-ipq4019: add missing error check
+    - marvell: pxa168_eth: fix call balance of pep->clk handling routines
+    - net: stmmac: dwmac-socfpga: Set RX watchdog interrupt as broken
+    - octeontx2-af: RPM: Fix mismatch in lmac type
+    - spi: atmel-quadspi: Fix register name in verbose logging function
+    - net: hsr: fix hsr_init_sk() vs network/transport headers.
+    - bnxt_en: Reserve rings after PCIe AER recovery if NIC interface is down
+    - iio: light: al3010: Fix an error handling path in al3010_probe()
+    - usb: using mutex lock and supporting O_NONBLOCK flag in iowarrior_read()
+    - usb: yurex: make waiting on yurex_write interruptible
+    - USB: chaoskey: fail open after removal
+    - USB: chaoskey: Fix possible deadlock chaoskey_list_lock
+    - misc: apds990x: Fix missing pm_runtime_disable()
+    - counter: stm32-timer-cnt: Add check for clk_enable()
+    - ALSA: hda/realtek: Update ALC256 depop procedure
+    - apparmor: fix 'Do simple duplicate message elimination'
+    - usb: ehci-spear: fix call balance of sehci clk handling routines
+    - Revert "drivers: clk: zynqmp: update divider round rate logic"
+    - ASoC: Intel: sst: Fix used of uninitialized ctx to log an error
+    - soc: qcom: socinfo: fix revision check in qcom_socinfo_probe()
+    - ext4: supress data-race warnings in ext4_free_inodes_{count,set}()
+    - ext4: fix FS_IOC_GETFSMAP handling
+    - jfs: xattr: check invalid xattr size more strictly
+    - ASoC: codecs: Fix atomicity violation in snd_soc_component_get_drvdata()
+    - perf/x86/intel/pt: Fix buffer full but size is 0 case
+    - crypto: x86/aegis128 - access 32-bit arguments as 32-bit
+    - powerpc/pseries: Fix KVM guest detection for disabling hardlockup detector
+    - KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
+    - fsnotify: fix sending inotify event with unexpected filename
+    - tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler
+    - locking/lockdep: Avoid creating new name string literals in
+      lockdep_set_subclass()
+    - exfat: fix uninit-value in __exfat_get_dentry_set
+    - Bluetooth: Fix type of len in rfcomm_sock_getsockopt{,_old}()
+    - usb: xhci: Fix TD invalidation under pending Set TR Dequeue
+    - Revert "usb: gadget: composite: fix OS descriptors w_value logic"
+    - serial: sh-sci: Clean sci_ports[0] after at earlycon exit
+    - Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"
+    - gpio: exar: set value when external pull-up or pull-down is present
+    - spi: Fix acpi deferred irq probe
+    - mtd: spi-nor: core: replace dummy buswidth from addr to data
+    - cpufreq: mediatek-hw: Fix wrong return value in mtk_cpufreq_get_cpu_power()
+    - platform/chrome: cros_ec_typec: fix missing fwnode reference decrement
+    - ubi: wl: Put source PEB into correct list if trying locking LEB failed
+    - serial: 8250: omap: Move pm_runtime_get_sync
+    - arm64: tls: Fix context-switching of tpidrro_el0 when kpti is enabled
+    - block: fix ordering between checking BLK_MQ_S_STOPPED request adding
+    - HID: wacom: Interpret tilt data from Intuos Pro BT as signed values
+    - soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
+    - media: v4l2-core: v4l2-dv-timings: check cvt/gtf result
+    - ALSA: hda/realtek: Update ALC225 depop procedure
+    - ALSA: hda/realtek: Set PCBeep to default value for ALC274
+    - ALSA: hda/realtek: Fix Internal Speaker and Mic boost of Infinix Y4 Max
+    - ALSA: hda/realtek: Apply quirk for Medion E15433
+    - usb: dwc3: gadget: Fix checking for number of TRBs left
+    - lib: string_helpers: silence snprintf() output truncation warning
+    - rpmsg: glink: Propagate TX failures in intentless mode as well
+    - um: Fix the return value of elf_core_copy_task_fpregs
+    - um: Always dump trace for specified task in show_stack
+    - rtc: st-lpc: Use IRQF_NO_AUTOEN flag in request_irq()
+    - rtc: abx80x: Fix WDT bit position of the status register
+    - ubifs: Correct the total block count by deducting journal reservation
+    - jffs2: fix use of uninitialized variable
+    - block: return unsigned int from bdev_io_min
+    - 9p/xen: fix init sequence
+    - rtc: ab-eoz9: don't fail temperature reads on undervoltage notification
+    - modpost: remove incorrect code in do_eisa_entry()
+    - nfs: ignore SB_RDONLY when mounting nfs
+    - sunrpc: remove unnecessary test in rpc_task_set_client()
+    - SUNRPC: Replace internal use of SOCKWQ_ASYNC_NOSPACE
+    - ASoC: fsl_micfil: fix the naming style for mask definition
+    - xfs: fix log recovery when unknown rocompat bits are set
+    - xfs: remove unknown compat feature check in superblock write validation
+    - btrfs: add might_sleep() annotations
+    - util_macros.h: fix/rework find_closest() macros
+    - scsi: ufs: exynos: Fix hibern8 notify callbacks
+    - PCI: keystone: Add link up check to ks_pcie_other_map_bus()
+    - ovl: properly handle large files in ovl_security_fileattr
+    - dm thin: Add missing destroy_work_on_stack()
+    - PCI: rockchip-ep: Fix address translation unit programming
+    - drm/etnaviv: flush shader L1 cache after user commandstream
+    - iTCO_wdt: mask NMI_NOW bit for update_no_reboot_bit() call
+    - watchdog: mediatek: Make sure system reset gets asserted in
+      mtk_wdt_restart()
+    - can: peak_usb: CANFD: store 64-bits hw timestamps
+    - can: do not increase rx statistics when generating a CAN rx error message
+      frame
+    - can: c_can: c_can_handle_bus_err(): update statistics if skb allocation
+      fails
+    - can: sun4i_can: sun4i_can_err(): call can_change_state() even if cf is NULL
+    - can: m_can: m_can_handle_lec_err(): fix {rx,tx}_errors statistics
+    - can: ifi_canfd: ifi_canfd_handle_lec_err(): fix {rx,tx}_errors statistics
+    - can: sun4i_can: sun4i_can_err(): fix {rx,tx}_errors statistics
+    - can: ems_usb: ems_usb_rx_err(): fix {rx,tx}_errors statistics
+    - ipvs: fix UB due to uninitialized stack access in ip_vs_protocol_init()
+    - ptp: Add error handling for adjfine callback in ptp_clock_adjtime
+    - net/sched: tbf: correct backlog statistic for GSO packets
+    - net/smc: Limit backlog connections
+    - net/qed: allow old cards not supporting "num_images" to work
+    - net: sched: fix erspan_opt settings in cls_flower
+    - netfilter: nft_set_hash: skip duplicated elements pending gc run
+    - netfilter: nft_set_hash: unaligned atomic read on struct nft_set_ext
+    - ethtool: Fix wrong mod state in case of verbose and no_mask bitset
+    - gpio: grgpio: use a helper variable to store the address of ofdev->dev
+    - dt_bindings: rs485: Correct delay values
+    - dt-bindings: serial: rs485: Fix rs485-rts-delay property
+    - serial: amba-pl011: Use port lock wrappers
+    - serial: amba-pl011: Fix RX stall when DMA is used
+    - bpftool: Remove asserts from JIT disassembler
+    - bpftool: fix potential NULL pointer dereferencing in prog_dump()
+    - drm/sti: Add __iomem for mixer_dbg_mxn's parameter
+    - ALSA: pcm: Add more disconnection checks at file ops
+    - ALSA: pcm: Avoid reference to status->state
+    - ALSA: usb-audio: Notify xrun for low-latency mode
+    - tools: Override makefile ARCH variable if defined, but empty
+    - drm/v3d: Enable Performance Counters before clearing them
+    - bpf: Handle BPF_EXIST and BPF_NOEXIST for LPM trie
+    - bpf: Fix exact match conditions in trie_get_next_key()
+    - watchdog: rti: of: honor timeout-sec property
+    - tracing: Fix cmp_entries_dup() to respect sort() comparison rules
+    - ALSA: usb-audio: add mixer mapping for Corsair HS80
+    - ALSA: hda/realtek: Enable mute and micmute LED on HP ProBook 430 G8
+    - ALSA: hda/realtek: Add support for Samsung Galaxy Book3 360 (NP730QFG)
+    - scsi: qla2xxx: Fix abort in bsg timeout
+    - scsi: qla2xxx: Fix NVMe and NPIV connect issue
+    - scsi: qla2xxx: Supported speed displayed incorrectly for VPorts
+    - scsi: qla2xxx: Remove check req_sg_cnt should be equal to rsp_sg_cnt
+    - dma-buf: fix dma_fence_array_signaled v4
+    - regmap: detach regmap from dev on regmap_exit
+    - mmc: sdhci-pci: Add DMI quirk for missing CD GPIO on Vexia Edu Atla 10
+      tablet
+    - mmc: core: Further prevent card detect during shutdown
+    - ocfs2: update seq_file index in ocfs2_dlm_seq_next
+    - epoll: annotate racy check
+    - btrfs: avoid unnecessary device path update for the same device
+    - kselftest/arm64: Don't leak pipe fds in pac.exec_sign_all()
+    - media: uvcvideo: Add a quirk for the Kaiweets KTI-W02 infrared camera
+    - media: cx231xx: Add support for Dexatek USB Video Grabber 1d19:6108
+    - drm/vc4: hvs: Set AXI panic modes for the HVS
+    - drm: panel-orientation-quirks: Add quirk for AYA NEO 2 model
+    - drm/mcde: Enable module autoloading
+    - drm/radeon/r600_cs: Fix possible int overflow in r600_packet3_check()
+    - r8169: don't apply UDP padding quirk on RTL8126A
+    - samples/bpf: Fix a resource leak
+    - net: fec_mpc52xx_phy: Use %pa to format resource_size_t
+    - net: ethernet: fs_enet: Use %pa to format resource_size_t
+    - net/sched: cbs: Fix integer overflow in cbs_set_port_rate()
+    - Bluetooth: L2CAP: handle NULL sock pointer in l2cap_sock_alloc
+    - wifi: ath5k: add PCI ID for SX76X
+    - wifi: ath5k: add PCI ID for Arcadyan devices
+    - drm/panel: simple: Add Microchip AC69T88A LVDS Display panel
+    - drm/amdgpu: clear RB_OVERFLOW bit when enabling interrupts for vega20_ih
+    - drm/amdgpu: Dereference the ATCS ACPI buffer
+    - drm/amdgpu: refine error handling in amdgpu_ttm_tt_pin_userptr
+    - drm/amdgpu: skip amdgpu_device_cache_pci_state under sriov
+    - wifi: ipw2x00: libipw_rx_any(): fix bad alignment
+    - ASoC: hdmi-codec: reorder channel allocation list
+    - rocker: fix link status detection in rocker_carrier_init()
+    - net/neighbor: clear error in case strict check is not set
+    - netpoll: Use rcu_access_pointer() in __netpoll_setup
+    - pinctrl: freescale: fix COMPILE_TEST error with PINCTRL_IMX_SCU
+    - tracing: Use atomic64_inc_return() in trace_clock_counter()
+    - scsi: st: Don't modify unknown block number in MTIOCGET
+    - scsi: st: Add MTIOCGET and MTLOAD to ioctls allowed after device reset
+    - pinctrl: qcom-pmic-gpio: add support for PM8937
+    - nvdimm: rectify the illogical code within nd_dax_probe()
+    - PCI: Detect and trust built-in Thunderbolt chips
+    - PCI: Add 'reset_subordinate' to reset hierarchy below bridge
+    - PCI: Add ACS quirk for Wangxun FF5xxx NICs
+    - usb: chipidea: udc: handle USB Error Interrupt if IOC not set
+    - misc: eeprom: eeprom_93cx6: Add quirk for extra read clock cycle
+    - modpost: Include '.text.*' in TEXT_SECTIONS
+    - modpost: Add .irqentry.text to OTHER_SECTIONS
+    - sched/core: Remove the unnecessary need_resched() check in nohz_csd_func()
+    - sched/fair: Add NOHZ balancer flag for nohz.next_balance updates
+    - sched/fair: Check idle_cpu() before need_resched() to detect ilb CPU turning
+      busy
+    - sched/core: Prevent wakeup of ksoftirqd during idle load balance
+    - btrfs: fix missing snapshot drew unlock when root is dead during swap
+      activation
+    - tracing/eprobe: Fix to release eprobe when failed to add dyn_event
+    - Revert "unicode: Don't special case ignorable code points"
+    - KVM: arm64: vgic-its: Add a data length check in vgic_its_save_*
+    - KVM: arm64: vgic-its: Clear DTE when MAPD unmaps a device
+    - KVM: arm64: vgic-its: Clear ITE when DISCARD frees an ITE
+    - jffs2: Fix rtime decompressor
+    - mm/damon/vaddr-test: split a test function having >1024 bytes frame size
+    - mm/damon/vaddr: fix issue in damon_va_evenly_split_region()
+    - xhci: dbc: Fix STALL transfer event handling
+    - mmc: mtk-sd: Fix error handle of probe function
+    - ocfs2: Revert "ocfs2: fix the la space leak when unmounting an ocfs2 volume"
+    - Revert "drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()"
+    - scsi: core: Fix scsi_mode_select() buffer length handling
+    - gve: Fixes for napi_poll when budget is 0
+    - arm64: smccc: Remove broken support for SMCCCv1.3 SVE discard hint
+    - net: dsa: microchip: correct KSZ8795 static MAC table access
+    - drm/amdgpu: rework resume handling for display (v2)
+    - serial: amba-pl011: fix build regression
+    - media: venus: vdec: fixed possible memory leak issue
+    - net/smc: Fix af_ops of child socket pointing to released memory
+    - Bluetooth: hci_core: Fix calling mgmt_device_connected
+    - Linux 5.15.174
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46871
+    - drm/amd/display: Correct the defined value for AMDGPU_DMUB_NOTIFICATION_MAX
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49950
+    - Bluetooth: L2CAP: Fix uaf in l2cap_connect
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50275
+    - arm64/sve: Discard stale CPU state when handling SVE traps
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-47730
+    - crypto: hisilicon/qm - inject error before stopping queue
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46809
+    - drm/amd/display: Check BIOS images before it is used
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57850
+    - jffs2: Prevent rtime decompress memory corruption
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56781
+    - powerpc/prom_init: Fixup missing powermac #size-cells
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56785
+    - MIPS: Loongson64: DTS: Really fix PCIe port nodes for ls7a
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-43098
+    - i3c: Use i3cdev->desc->info instead of calling i3c_device_get_info() to
+      avoid deadlock
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-45828
+    - i3c: mipi-i3c-hci: Mask ring interrupts before ring stop request
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56586
+    - f2fs: fix f2fs_bug_on when uninstalling filesystem call f2fs_evict_inode.
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56587
+    - leds: class: Protect brightness_show() with led_cdev->led_access mutex
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56589
+    - scsi: hisi_sas: Add cond_resched() for no forced preemption model
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56590
+    - Bluetooth: hci_core: Fix not checking skb length on hci_acldata_packet
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56593
+    - wifi: brcmfmac: Fix oops due to NULL pointer dereference in
+      brcmf_sdiod_sglist_rw()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56594
+    - drm/amdgpu: set the right AMDGPU sg segment limitation
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56595
+    - jfs: add a check to prevent array-index-out-of-bounds in dbAdjTree
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56596
+    - jfs: fix array-index-out-of-bounds in jfs_readdir
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56597
+    - jfs: fix shift-out-of-bounds in dbSplit
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56598
+    - jfs: array-index-out-of-bounds fix in dtReadFirst
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-47143
+    - dma-debug: fix a possible deadlock on radix_lock
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56600
+    - net: inet6: do not leave a dangling sk pointer in inet6_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56601
+    - net: inet: do not leave a dangling sk pointer in inet_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56602
+    - net: ieee802154: do not leave a dangling sk pointer in ieee802154_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56603
+    - net: af_can: do not leave a dangling sk pointer in can_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56605
+    - Bluetooth: L2CAP: do not leave dangling sk pointer on error in
+      l2cap_sock_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56606
+    - af_packet: avoid erroring out after sock_init_data() in packet_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56787
+    - soc: imx8m: Probe the SoC driver as platform driver
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56610
+    - kcsan: Turn report_filterlist_lock into a raw_spinlock
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57849
+    - s390/cpum_sf: Handle CPU hotplug remove during sampling
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56568
+    - iommu/arm-smmu: Defer probe of clients after smmu device bound
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56614
+    - xsk: fix OOB map writes when deleting elements
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56615
+    - bpf: fix OOB devmap writes when deleting elements
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-48881
+    - bcache: revert replacing IS_ERR_OR_NULL with IS_ERR again
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56619
+    - nilfs2: fix potential out-of-bounds memory access in nilfs_find_entry()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56622
+    - scsi: ufs: core: sysfs: Prevent div by zero
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56623
+    - scsi: qla2xxx: Fix use after free on unload
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57874
+    - arm64: ptrace: fix partial SETREGSET for NT_ARM_TAGGED_ADDR_CTRL
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56625
+    - can: dev: can_set_termination(): allow sleeping GPIOs
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56629
+    - HID: wacom: fix when get product name maybe null pointer
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56630
+    - ocfs2: free inode when ocfs2_get_init_inode() fails
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50051
+    - spi: mpc52xx: Add cancel_work_sync before module remove
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56633
+    - tcp_bpf: Fix the sk_mem_uncharge logic in tcp_bpf_sendmsg
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56634
+    - gpio: grgpio: Add NULL check in grgpio_probe
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56636
+    - geneve: do not assume mac header is set in geneve_xmit_skb()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56637
+    - netfilter: ipset: Hold module reference while requesting a module
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-52332
+    - igb: Fix potential invalid memory access in igb_init_module()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56640
+    - net/smc: fix LGR and link use-after-free issue
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56642
+    - tipc: Fix use-after-free of kernel socket in cleanup_bearer().
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56643
+    - dccp: Fix memory leak in dccp_feat_change_recv
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56644
+    - net/ipv6: release expired exception dst cached in socket
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56645
+    - can: j1939: j1939_session_new(): fix skb reference counting
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56648
+    - net: hsr: avoid potential out-of-bound access in fill_frame_info()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56650
+    - netfilter: x_tables: fix LED ID check in led_tg_check()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56776
+    - drm/sti: avoid potential dereference of error pointers
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56777
+    - drm/sti: avoid potential dereference of error pointers in
+      sti_gdp_atomic_check
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56778
+    - drm/sti: avoid potential dereference of error pointers in
+      sti_hqvdp_atomic_check
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46841
+    - btrfs: don't BUG_ON on ENOMEM from btrfs_lookup_extent_info() in
+      walk_down_proc()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56779
+    - nfsd: fix nfs4_openowner leak when concurrent nfsd4_open occur
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56558
+    - nfsd: make sure exp active before svc_export_show
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56562
+    - i3c: master: Fix miss free init_dyn_addr at i3c_master_put_i3c_addrs()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57838
+    - s390/entry: Mark IRQ entries to fix stack depot warnings
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56567
+    - ad7780: fix division by zero in ad7780_write_raw()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56581
+    - btrfs: ref-verify: fix use-after-free after invalid ref action
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56774
+    - btrfs: add a sanity check for btrfs root in btrfs_search_slot()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56780
+    - quota: flush quota_release_work upon quota writeback
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53165
+    - sh: intc: Fix use-after-free bug in register_intc_controller()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56688
+    - sunrpc: clear XPRT_SOCK_UPD_TIMEOUT when reset transport
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56704
+    - 9p/xen: fix release of IRQ
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53171
+    - ubifs: authentication: Fix use-after-free in ubifs_tnc_end_commit
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53172
+    - ubi: fastmap: Fix duplicate slab cache names while attaching
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56739
+    - rtc: check if __rtc_read_time was successful in rtc_timer_do_work()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53173
+    - NFSv4.0: Fix a use-after-free problem in the asynchronous open()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53145
+    - um: Fix potential integer overflow during physmem setup
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53174
+    - SUNRPC: make sure cache entry active before cache_show
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53146
+    - NFSD: Prevent a potential integer overflow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56698
+    - usb: dwc3: gadget: Fix looping of queued SG entries
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53180
+    - ALSA: pcm: Add sanity NULL check for the default mmap fault handler
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56700
+    - media: wl128x: Fix atomicity violation in fmc_send_cmd()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2022-49034
+    - sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53181
+    - um: vector: Do not use drvdata in release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53183
+    - um: net: Do not use drvdata in release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53184
+    - um: ubd: Do not use drvdata in release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50055
+    - driver core: bus: Fix double free in driver API bus_register()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56741
+    - apparmor: test: Fix memory leak for aa_unpack_strdup()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53148
+    - comedi: Flush partial mappings in error case
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53194
+    - PCI: Fix use-after-free of slot->bus on hot remove
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53197
+    - ALSA: usb-audio: Fix potential out-of-bound accesses for Extigy and Mbox
+      devices
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53150
+    - ALSA: usb-audio: Fix out of bounds reads when finding clock sources
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53198
+    - xen: Fix the issue of resource not being properly released in
+      xenbus_dev_probe()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50283
+    - ksmbd: fix slab-use-after-free in smb3_preauth_hash_rsp
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53206
+    - tcp: Fix use-after-free of nreq in reqsk_timer_handler().
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53214
+    - vfio/pci: Properly hide first-in-list PCIe extended capability
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53215
+    - svcrdma: fix miss destroy percpu_counter in svc_rdma_proc_init()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53217
+    - NFSD: Prevent NULL dereference in nfsd4_process_cb_update()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53151
+    - svcrdma: Address an integer overflow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56745
+    - PCI: Fix reset_method_store() memory leak
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56746
+    - fbdev: sh7760fb: Fix a possible memory leak in sh7760fb_alloc_mem()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53155
+    - ocfs2: fix uninitialized value in ocfs2_file_read_iter()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53226
+    - RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56747
+    - scsi: qedi: Fix a possible memory leak in qedi_alloc_and_init_sb()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56748
+    - scsi: qedf: Fix a possible memory leak in qedf_alloc_and_init_sb()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53227
+    - scsi: bfa: Fix use-after-free in bfad_im_module_exit()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56701
+    - powerpc/pseries: Fix dtl_access_lock to be a rw_semaphore
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56678
+    - powerpc/mm/fault: Fix kfence page fault reporting
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56723
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for PMIC devices
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56724
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for TMU device
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56691
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for USB Type-C device
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56694
+    - bpf: fix recursive lock when verdict program return SK_PASS
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53237
+    - Bluetooth: fix use-after-free in device_for_each_child()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53239
+    - ALSA: 6fire: Release resources at card release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56531
+    - ALSA: caiaq: Use snd_card_free_when_closed() at disconnection
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56532
+    - ALSA: us122l: Use snd_card_free_when_closed() at disconnection
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56533
+    - ALSA: usx2y: Use snd_card_free_when_closed() at disconnection
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56720
+    - bpf, sockmap: Several fixes to bpf_msg_pop_data
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56726
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in cn10k.c
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56728
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_ethtool.c
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56679
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_common.c
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56539
+    - wifi: mwifiex: Fix memcpy() field-spanning write warning in
+      mwifiex_config_scan()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53156
+    - wifi: ath9k: add range check for conn_rsp_epid in htc_connect_service()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56705
+    - media: atomisp: Add check for rgby_data memory allocation failure
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53157
+    - firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53158
+    - soc: qcom: geni-se: fix array underflow in geni_se_clk_tbl_get()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56681
+    - crypto: bcm - add error check in the ahash_hmac_init function
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56708
+    - EDAC/igen6: Avoid segmentation fault on module unload
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56690
+    - crypto: pcrypt - Call crypto layer directly when padata_do_parallel() return
+      -EBUSY
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53161
+    - EDAC/bluefield: Fix potential integer overflow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56754
+    - crypto: caam - Fix the pointer passed to caam_qi_shutdown()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56548
+    - hfsplus: don't query the device logical block size multiple times
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56756
+    - nvme-pci: fix freeing of the HMB descriptor table
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53142
+    - initramfs: avoid filename buffer overrun
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56693
+    - brd: defer automatic disk creation until module initialization succeeds
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49996
+    - cifs: Fix buffer overflow when parsing NFS reparse points
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53096
+    - mm: resolve faulty mmap_region() error path behaviour
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53122
+    - mptcp: cope racing subflow creation in mptcp_rcv_space_adjust
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49974
+    - NFSD: Limit the number of concurrent async COPY operations
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53127
+    - Revert "mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K"
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53130
+    - nilfs2: fix null-ptr-deref in block_dirty_buffer tracepoint
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53131
+    - nilfs2: fix null-ptr-deref in block_touch_buffer tracepoint
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53135
+    - KVM: VMX: Bury Intel PT virtualization (guest/host mode) behind
+      CONFIG_BROKEN
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53112
+    - ocfs2: uncache inode which has failed entering the group
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53113
+    - mm: fix NULL pointer dereference in alloc_pages_bulk_noprof
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53120
+    - net/mlx5e: CT: Fix null-ptr-deref in add rule err flow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53138
+    - net/mlx5e: kTLS, Fix incorrect page refcounting
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53121
+    - net/mlx5: fs, lock FTE when checking if active
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53129
+    - drm/rockchip: vop: Fix a dereferenced before check warning
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53140
+    - netlink: terminate outstanding dump on socket close
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56569
+    - ftrace: Fix regression with module command in stack_trace_filter
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56570
+    - ovl: Filter invalid inodes with missing lookup function
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56572
+    - media: platform: allegro-dvt: Fix possible memory leak in
+      allocate_buffers_internal()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56574
+    - media: ts2020: fix null-ptr-deref in ts2020_probe()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56575
+    - media: imx-jpeg: Ensure power suppliers be suspended before detach them
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56576
+    - media: i2c: tc358743: Fix crash in the probe error path when using polling
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56578
+    - media: imx-jpeg: Set video drvdata before register video device
+  * CVE-2024-56672
+    - blk-cgroup: Fix UAF in blkcg_unpin_online()
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Thu, 06 Mar 2025 12:03:48 +0800
+
+linux-xilinx-zynqmp (5.15.0-1043.47) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1043.47 -proposed tracker (LP: #2093732)
+
+  [ Ubuntu: 5.15.0-133.144 ]
+
+  * CVE-2025-0927
+    - SAUCE: fs: hfs/hfsplus: add key_len boundary check to hfs_bnode_read_key
+
+  [ Ubuntu: 5.15.0-132.143 ]
+
+  * jammy/linux: 5.15.0-132.143 -proposed tracker (LP: #2093735)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.01.13)
+  * KVM: Cache CPUID at KVM.ko module init to reduce latency of VM-Enter and VM-
+    Exit (LP: #2093146)
+    - kvm: x86: Fix xstate_required_size() to follow XSTATE alignment rule
+    - KVM: x86: Cache CPUID.0xD XSTATE offsets+sizes during module init
+  * Jammy update: v5.15.173 upstream stable release (LP: #2089541)
+    - 9p: Avoid creating multiple slab caches with the same name
+    - irqchip/ocelot: Fix trigger register address
+    - block: Fix elevator_get_default() checking for NULL q->tag_set
+    - HID: multitouch: Add support for B2402FVA track point
+    - HID: multitouch: Add quirk for HONOR MagicBook Art 14 touchpad
+    - bpf: use kvzmalloc to allocate BPF verifier environment
+    - crypto: marvell/cesa - Disable hash algorithms
+    - sound: Make CONFIG_SND depend on INDIRECT_IOMEM instead of UML
+    - drm/vmwgfx: Limit display layout ioctl array size to
+      VMWGFX_NUM_DISPLAY_UNITS
+    - powerpc/powernv: Free name on error in opal_event_init()
+    - vDPA/ifcvf: Fix pci_read_config_byte() return code handling
+    - fs: Fix uninitialized value issue in from_kuid and from_kgid
+    - HID: multitouch: Add quirk for Logitech Bolt receiver w/ Casa touchpad
+    - HID: lenovo: Add support for Thinkpad X1 Tablet Gen 3 keyboard
+    - net: usb: qmi_wwan: add Fibocom FG132 0x0112 composition
+    - md/raid10: improve code of mrdev in raid10_sync_request
+    - mm/memory: add non-anonymous page check in the copy_present_page()
+    - udf: Allocate name buffer in directory iterator on heap
+    - udf: Avoid directory type conversion failure due to ENOMEM
+    - 9p: fix slab cache name creation for real
+    - Linux 5.15.173
+  * Jammy update: v5.15.173 upstream stable release (LP: #2089541) //
+    CVE-2024-41080
+    - io_uring: fix possible deadlock in io_register_iowq_max_workers()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533)
+    - arm64: dts: rockchip: Fix rt5651 compatible value on rk3399-sapphire-
+      excavator
+    - arm64: dts: rockchip: Remove hdmi's 2nd interrupt on rk3328
+    - arm64: dts: rockchip: Fix bluetooth properties on Rock960 boards
+    - arm64: dts: rockchip: Remove #cooling-cells from fan on Theobroma lion
+    - arm64: dts: rockchip: Fix LED triggers on rk3308-roc-cc
+    - arm64: dts: imx8mp: correct sdhc ipg clk
+    - ARM: dts: rockchip: fix rk3036 acodec node
+    - ARM: dts: rockchip: drop grf reference from rk3036 hdmi
+    - ARM: dts: rockchip: Fix the spi controller on rk3036
+    - ARM: dts: rockchip: Fix the realtek audio codec on rk3036-kylin
+    - NFSv3: only use NFS timeout for MOUNT when protocols are compatible
+    - NFS: Add a tracepoint to show the results of nfs_set_cache_invalid()
+    - NFSv3: handle out-of-order write replies.
+    - nfs: avoid i_lock contention in nfs_clear_invalid_mapping
+    - net: enetc: set MAC address to the VF net_device
+    - can: c_can: fix {rx,tx}_errors statistics
+    - net: phy: ti: add PHY_RST_AFTER_CLK_EN flag
+    - net: stmmac: Fix unbalanced IRQ wake disable warning on single irq case
+    - Revert "ALSA: hda/conexant: Mute speakers at suspend / shutdown"
+    - media: stb0899_algo: initialize cfr before using it
+    - media: dvb_frontend: don't play tricks with underflow values
+    - media: adv7604: prevent underflow condition when reporting colorspace
+    - scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
+    - ALSA: firewire-lib: fix return value on fail in amdtp_tscm_init()
+    - media: pulse8-cec: fix data timestamp at pulse8_setup()
+    - media: v4l2-ctrls-api: fix error handling for v4l2_g_ctrl()
+    - pwm: imx-tpm: Use correct MODULO value for EPWM mode
+    - drm/amdgpu: Adjust debugfs eviction and IB access permissions
+    - drm/amdgpu: prevent NULL pointer dereference if ATIF is not supported
+    - thermal/drivers/qcom/lmh: Remove false lockdep backtrace
+    - dm cache: correct the number of origin blocks to match the target length
+    - dm cache: optimize dirty bit checking with find_next_bit when resizing
+    - dm-unstriped: cast an operand to sector_t to prevent potential uint32_t
+      overflow
+    - ALSA: usb-audio: Add quirk for HP 320 FHD Webcam
+    - posix-cpu-timers: Clear TICK_DEP_BIT_POSIX_TIMER on clone
+    - io_uring: rename kiocb_end_write() local helper
+    - fs: create kiocb_{start,end}_write() helpers
+    - io_uring: use kiocb_{start,end}_write() helpers
+    - media: uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in
+      uvc_parse_format
+    - fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
+    - usb: dwc3: fix fault at system suspend if device was already runtime
+      suspended
+    - USB: serial: qcserial: add support for Sierra Wireless EM86xx
+    - USB: serial: option: add Fibocom FG132 0x0112 composition
+    - USB: serial: option: add Quectel RG650V
+    - irqchip/gic-v3: Force propagation of the active state with a read-back
+    - ucounts: fix counter leak in inc_rlimit_get_ucounts()
+    - ALSA: usb-audio: Support jack detection on Dell dock
+    - ALSA: usb-audio: Add quirks for Dell WD19 dock
+    - ACPI: PRM: Clean up guid type in struct prm_handler_info
+    - ALSA: usb-audio: Add endianness annotations
+    - Linux 5.15.172
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50265
+    - ocfs2: remove entry once instead of null-ptr-dereference in
+      ocfs2_xa_remove()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50267
+    - USB: serial: io_edgeport: fix use after free in debug printk
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50268
+    - usb: typec: fix potential out of bounds in ucsi_ccg_update_set_new_cam_cmd()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50269
+    - usb: musb: sunxi: Fix accessing an released usb phy
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50036
+    - net: do not delay dst_entries_add() in dst_release()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-42291
+    - ice: Add a per-VF limit on number of FDIR filters
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50273
+    - btrfs: reinitialize delayed ref list after deleting it from the list
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53066
+    - nfs: Fix KMSAN warning in decode_getfattr_attrs()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53052
+    - io_uring/rw: fix missing NOWAIT check for O_DIRECT start write
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50278
+    - dm cache: fix potential out-of-bounds access on the first resume
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50279
+    - dm cache: fix out-of-bounds access to the dirty bitset when resizing
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50282
+    - drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50287
+    - media: v4l2-tpg: prevent the risk of a division by zero
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50290
+    - media: cx24116: prevent overflows on SNR calculus
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53061
+    - media: s5p-jpeg: prevent buffer overflows
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50292
+    - ASoC: stm32: spdifrx: fix dma channel release in stm32_spdifrx_remove
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53063
+    - media: dvbdev: prevent the risk of out of memory access
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50295
+    - net: arc: fix the device for dma_map_single/dma_unmap_single
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50296
+    - net: hns3: fix kernel crash when uninstalling driver
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53088
+    - i40e: fix race condition by adding filter's intermediate sync state
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50299
+    - sctp: properly validate chunk size in sctp_sf_ootb()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50301
+    - security/keys: fix slab-out-of-bounds in key_task_permission
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50302
+    - HID: core: zero-initialize the report buffer
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405)
+    - selftests/mm: fix incorrect buffer->mirror size in hmm2 double_map test
+    - ACPI: PRM: Remove unnecessary blank lines
+    - ACPI: PRM: Change handler_addr type to void pointer
+    - cgroup: Fix potential overflow issue when checking max_depth
+    - mac80211: MAC80211_MESSAGE_TRACING should depend on TRACING
+    - wifi: mac80211: skip non-uploaded keys in ieee80211_iter_keys
+    - wifi: brcm80211: BRCM_TRACING should depend on TRACING
+    - RDMA/cxgb4: Dump vendor specific QP details
+    - RDMA/mlx5: Round max_rd_atomic/max_dest_rd_atomic up instead of down
+    - RDMA/bnxt_re: synchronize the qp-handle table array
+    - mac80211: do drv_reconfig_complete() before restarting all
+    - mac80211: Add support to trigger sta disconnect on hardware restart
+    - wifi: iwlwifi: mvm: disconnect station vifs if recovery failed
+    - ASoC: cs42l51: Fix some error handling paths in cs42l51_probe()
+    - gtp: allow -1 to be specified as file description from userspace
+    - net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension
+    - firmware: arm_sdei: Fix the input parameter of cpuhp_remove_state()
+    - fs/ntfs3: Fix warning possible deadlock in ntfs_set_state
+    - scsi: scsi_transport_fc: Allow setting rport state to current state
+    - net: amd: mvme147: Fix probe banner message
+    - NFS: remove revoked delegation from server's delegation list
+    - misc: sgi-gru: Don't disable preemption in GRU driver
+    - usbip: tools: Fix detach_port() invalid port error path
+    - usb: phy: Fix API devm_usb_put_phy() can not release the phy
+    - usb: typec: fix unreleased fwnode_handle in typec_port_register_altmodes()
+    - xhci: Fix Link TRB DMA in command ring stopped completion event
+    - xhci: Use pm_runtime_get to prevent RPM on unsupported systems
+    - Revert "driver core: Fix uevent_show() vs driver detach race"
+    - iio: light: veml6030: fix microlux value calculation
+    - riscv: vdso: Prevent the compiler from inserting calls to memset()
+    - riscv: efi: Set NX compat flag in PE/COFF header
+    - riscv: Use '%u' to format the output of 'cpu'
+    - riscv: Remove unused GENERATING_ASM_OFFSETS
+    - riscv: Remove duplicated GET_RM
+    - mm/page_alloc: call check_new_pages() while zone spinlock is not held
+    - mm/page_alloc: fix tracepoint mm_page_alloc_zone_locked()
+    - mm/page_alloc: split out buddy removal code from rmqueue into separate
+      helper
+    - mm/page_alloc: rename ALLOC_HIGH to ALLOC_MIN_RESERVE
+    - mm/page_alloc: treat RT tasks similar to __GFP_HIGH
+    - mm/page_alloc: explicitly record high-order atomic allocations in
+      alloc_flags
+    - mm/page_alloc: explicitly define what alloc flags deplete min reserves
+    - mm/page_alloc: explicitly define how __GFP_HIGH non-blocking allocations
+      accesses reserves
+    - Revert "drm/mipi-dsi: Set the fwnode for mipi_dsi_device"
+    - vt: prevent kernel-infoleak in con_font_get()
+    - mac80211: always have ieee80211_sta_restart()
+    - Linux 5.15.171
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2023-52913
+    - drm/i915: Fix potential context UAFs
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50228
+    - mm: shmem: fix data-race in shmem_getattr()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53055
+    - wifi: iwlwifi: mvm: fix 6 GHz scan construction
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50230
+    - nilfs2: fix kernel bug due to missing clearing of checked flag
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50072
+    - x86/bugs: Use code segment selector for VERW operand
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50218
+    - ocfs2: pass u64 to ocfs2_truncate_inline maybe overflow
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50219
+    - mm/page_alloc: let GFP_ATOMIC order-0 allocs access highatomic reserves
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50229
+    - nilfs2: fix potential deadlock with newly created symlinks
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50232
+    - iio: adc: ad7124: fix division by zero in ad7124_set_channel_odr()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50233
+    - staging: iio: frequency: ad9832: fix division by zero in
+      ad9832_calc_freqreg()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50234
+    - wifi: iwlegacy: Clear stale interrupts before resuming device
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50236
+    - wifi: ath10k: Fix memory leak in management tx
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50237
+    - wifi: mac80211: do not pass a stopped vif to the driver in .get_txpower
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50244
+    - fs/ntfs3: Additional check in ni_clear()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50245
+    - fs/ntfs3: Fix possible deadlock in mi_read
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50247
+    - fs/ntfs3: Check if more than chunk-size bytes are written
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50249
+    - ACPI: CPPC: Make rmw_lock a raw_spin_lock
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50251
+    - netfilter: nft_payload: sanitize offset and length before calling
+      skb_checksum()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50257
+    - netfilter: Fix use-after-free in get_info()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50262
+    - bpf: Fix out-of-bounds write in trie_get_next_key()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50259
+    - netdevsim: Add trailing zero to terminate the string in
+      nsim_nexthop_bucket_activity_write()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53042
+    - ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_init_flow()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53058
+    - net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53059
+    - wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50141
+    - ACPI: PRM: Find EFI_MEMORY_RUNTIME block for PRM handler and context
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50086
+    - ksmbd: fix user-after-free from session log off
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272)
+    - RDMA/bnxt_re: Fix incorrect AVID type in WQE structure
+    - x86/resctrl: Avoid overflow in MB settings in bw_validate()
+    - ARM: dts: bcm2837-rpi-cm3-io3: Fix HDMI hpd-gpio pin
+    - RDMA/cxgb4: Fix RDMA_CM_EVENT_UNREACHABLE error for iWARP
+    - RDMA/irdma: Fix misspelling of "accept*"
+    - ipv4: give an IPv4 dev to blackhole_netdev
+    - RDMA/bnxt_re: Return more meaningful error
+    - drm/msm/dsi: fix 32-bit signed integer extension in pclk_rate calculation
+    - drm/msm: Allocate memory for disp snapshot with kvzalloc()
+    - net: usb: usbnet: fix race in probe failure
+    - octeontx2-af: Fix potential integer overflows on integer shifts
+    - macsec: don't increment counters for an unrelated SA
+    - net: ethernet: aeroflex: fix potential memory leak in
+      greth_start_xmit_gbit()
+    - net/smc: Fix searching in list of known pnetids in smc_pnet_add_pnetid
+    - net: xilinx: axienet: fix potential memory leak in axienet_start_xmit()
+    - genetlink: hold RCU in genlmsg_mcast()
+    - s390: Initialize psw mask in perf_arch_fetch_caller_regs()
+    - arm64:uprobe fix the uprobe SWBP_INSN in big-endian
+    - KVM: s390: gaccess: Check if guest address is in memslot
+    - usb: gadget: Add function wakeup support
+    - XHCI: Separate PORT and CAPs macros into dedicated file
+    - usb: dwc3: core: Fix system suspend on TI AM62 platforms
+    - block, bfq: fix procress reference leakage for bfqq in merge chain
+    - ASoC: codecs: lpass-rx-macro: add missing CDC_RX_BCL_VBAT_RF_PROC2 to
+      default regs values
+    - ASoC: fsl_sai: Enable 'FIFO continue on error' FCONT bit
+    - arm64: Force position-independent veneers
+    - platform/x86: dell-wmi: Ignore suspend notifications
+    - arm64/uprobes: change the uprobe_opcode_t typedef to fix the sparse warning
+    - ASoC: qcom: sm8250: add qrb4210-rb2-sndcard compatible string
+    - platform/x86: dell-sysman: add support for alienware products
+    - jfs: Fix sanity check in dbMount
+    - xfrm: extract dst lookup parameters into a struct
+    - xfrm: respect ip protocols rules criteria when performing dst lookups
+    - net: plip: fix break; causing plip to never transmit
+    - net: dsa: mv88e6xxx: Fix error when setting port policy on mv88e6393x
+    - net: usb: usbnet: fix name regression
+    - r8169: avoid unsolicited interrupts
+    - posix-clock: posix-clock: Fix unbalanced locking in pc_clock_settime()
+    - bpf,perf: Fix perf_event_detach_bpf_prog error handling
+    - ALSA: hda/realtek: Update default depop procedure
+    - btrfs: zoned: fix zone unusable accounting for freed reserved extent
+    - ACPI: resource: Add LG 16T90SP to irq1_level_low_skip_override[]
+    - ACPI: button: Add DMI quirk for Samsung Galaxy Book2 to fix initial lid
+      detection issue
+    - openat2: explicitly return -E2BIG for (usize > PAGE_SIZE)
+    - ALSA: hda/realtek: Add subwoofer quirk for Acer Predator G9-593
+    - hv_netvsc: Fix VF namespace also in synthetic NIC NETDEV_REGISTER event
+    - selinux: improve error checking in sel_write_load()
+    - net: phy: dp83822: Fix reset pin definitions
+    - Linux 5.15.170
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50142
+    - xfrm: validate new SA's prefixlen using SA family when sel.family is unset
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50103
+    - ASoC: qcom: Fix NULL Dereference in asoc_qcom_lpass_cpu_platform_probe()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50058
+    - serial: protect uart_port_dtr_rts() in uart_shutdown() too
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50110
+    - xfrm: fix one more kernel-infoleak in algo dumping
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50115
+    - KVM: nSVM: Ignore nCR3[4:0] when loading PDPTEs from memory
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50116
+    - nilfs2: fix kernel bug due to missing clearing of buffer delay flag
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50117
+    - drm/amd: Guard against bad data for ATIF ACPI method
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50205
+    - ALSA: firewire-lib: Avoid division by zero in apply_constraint_to_size()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50127
+    - net: sched: fix use-after-free in taprio_change()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50128
+    - net: wwan: fix global oob in wwan_rtnl_policy
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50167
+    - be2net: fix potential memory leak in be_xmit()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50168
+    - net/sun3_82586: fix potential memory leak in sun3_82586_send_packet()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50131
+    - tracing: Consider the NULL character when validating the event length
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50143
+    - udf: fix uninit-value use in udf_get_fileshortad
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50134
+    - drm/vboxvideo: Replace fake VLA at end of vbva_mouse_pointer_shape with real
+      VLA
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50010
+    - exec: don't WARN for racy path_noexec check
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50194
+    - arm64: probes: Fix uprobes for big-endian kernels
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50148
+    - Bluetooth: bnep: fix wild-memory-access in proto_unregister
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50150
+    - usb: typec: altmode should keep reference to parent
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50151
+    - smb: client: fix OOBs when building SMB2_IOCTL request
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50153
+    - scsi: target: core: Fix null-ptr-deref in target_alloc_device()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50154
+    - tcp/dccp: Don't use timer_pending() in reqsk_queue_unlink().
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50171
+    - net: systemport: fix potential memory leak in bcm_sysport_xmit()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50156
+    - drm/msm: Avoid NULL dereference in msm_disp_state_print_regs()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50208
+    - RDMA/bnxt_re: Fix a bug while setting up Level-2 PBL pages
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50160
+    - ALSA: hda/cs8409: Fix possible NULL dereference
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50209
+    - RDMA/bnxt_re: Add a check for memory allocation
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50162
+    - bpf: devmap: provide rxq after redirect
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50163
+    - bpf: Make sure internal and UAPI bpf_redirect flags don't overlap
+  * kernel:nft "Could not process rule: Device or resource busy" on unreferenced
+    chain (LP: #2089699)
+    - SAUCE: netfilter: nf_tables: Fix EBUSY on deleting unreferenced chain
+  * WARN in trc_wait_for_one_reader about failed IPIs (LP: #2089373)
+    - SAUCE: rcu-tasks: fix mismerge in trc_inspect_reader
+    - rcu-tasks: Idle tasks on offline CPUs are in quiescent states
+  * CVE-2024-35887
+    - ax25: fix use-after-free bugs caused by ax25_ds_del_timer
+  * CVE-2024-40965
+    - clk: Add a devm variant of clk_rate_exclusive_get()
+    - clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()
+    - i2c: lpi2c: Avoid calling clk_get_rate during transfer
+  * CVE-2024-40982
+    - ssb: Fix potential NULL pointer dereference in ssb_device_uevent()
+  * CVE-2024-41066
+    - ibmvnic: Add tx check to prevent skb leak
+  * CVE-2024-42252
+    - closures: Change BUG_ON() to WARN_ON()
+  * CVE-2024-53097
+    - mm: krealloc: Fix MTE false alarm in __do_krealloc
+  * Add list of source files to linux-buildinfo (LP: #2086606)
+    - [Packaging] Sort build dependencies alphabetically
+    - [Packaging] Add list of used source files to buildinfo package
+  * UFS: uspi->s_3apb UBSAN: shift-out-of-bounds (LP: #2087853)
+    - ufs: ufs_sb_private_info: remove unused s_{2, 3}apb fields
+  * Jammy update: v5.15.169 upstream stable release (LP: #2088231)
+    - ALSA: hda/conexant - Fix audio routing for HP EliteOne 1000 G2
+    - udf: New directory iteration code
+    - udf: Convert udf_expand_dir_adinicb() to new directory iteration
+    - udf: Move udf_expand_dir_adinicb() to its callsite
+    - udf: Implement searching for directory entry using new iteration code
+    - udf: Provide function to mark entry as deleted using new directory iteration
+      code
+    - udf: Convert udf_rename() to new directory iteration code
+    - udf: Convert udf_readdir() to new directory iteration
+    - udf: Convert udf_lookup() to use new directory iteration code
+    - udf: Convert udf_get_parent() to new directory iteration code
+    - udf: Convert empty_dir() to new directory iteration code
+    - udf: Convert udf_rmdir() to new directory iteration code
+    - udf: Convert udf_unlink() to new directory iteration code
+    - udf: Implement adding of dir entries using new iteration code
+    - udf: Convert udf_add_nondir() to new directory iteration
+    - udf: Convert udf_mkdir() to new directory iteration code
+    - udf: Convert udf_link() to new directory iteration code
+    - udf: Remove old directory iteration code
+    - udf: Handle error when expanding directory
+    - udf: Don't return bh from udf_expand_dir_adinicb()
+    - udf: Fix bogus checksum computation in udf_rename()
+    - net: enetc: remove xdp_drops statistic from enetc_xdp_drop()
+    - net: enetc: add missing static descriptor and inline keyword
+    - posix-clock: Fix missing timespec64 check in pc_clock_settime()
+    - arm64: probes: Remove broken LDR (literal) uprobe support
+    - arm64: probes: Fix simulate_ldr*_literal()
+    - net: macb: Avoid 20s boot delay by skipping MDIO bus registration for fixed-
+      link PHY
+    - irqchip/gic-v3-its: Fix VSYNC referencing an unmapped VPE on GIC v4.1
+    - fat: fix uninitialized variable
+    - mm/swapfile: skip HugeTLB pages for unuse_vma
+    - secretmem: disable memfd_secret() if arch cannot set direct map
+    - dm-crypt, dm-verity: disable tasklets
+    - KVM: Fix a data race on last_boosted_vcpu in kvm_vcpu_on_spin()
+    - drm/shmem-helper: Fix BUG_ON() on mmap(PROT_WRITE, MAP_PRIVATE)
+    - io_uring/sqpoll: do not allow pinning outside of cpuset
+    - io_uring/sqpoll: retain test for whether the CPU is valid
+    - io_uring/sqpoll: do not put cpumask on stack
+    - iommu/vt-d: Fix incorrect pci_for_each_dma_alias() for non-PCI devices
+    - s390/sclp_vt220: Convert newlines to CRLF instead of LFCR
+    - KVM: s390: Change virtual to physical address access in diag 0x258 handler
+    - x86/cpufeatures: Define X86_FEATURE_AMD_IBPB_RET
+    - x86/cpufeatures: Add a IBPB_NO_RET BUG flag
+    - x86/entry: Have entry_ibpb() invalidate return predictions
+    - x86/bugs: Skip RSB fill at VMEXIT
+    - x86/bugs: Do not use UNTRAIN_RET with IBPB on entry
+    - blk-rq-qos: fix crash on rq_qos_wait vs. rq_qos_wake_function race
+    - io_uring/sqpoll: close race on waiting for sqring entries
+    - drm/radeon: Fix encoder->possible_clones
+    - drm/vmwgfx: Handle surface check failure correctly
+    - iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
+    - iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
+    - iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
+    - iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - iio: hid-sensors: Fix an error handling path in
+      _hid_sensor_set_report_latency()
+    - iio: light: veml6030: fix ALS sensor resolution
+    - iio: light: veml6030: fix IIO device retrieval from embedded device
+    - iio: light: opt3001: add missing full-scale range value
+    - iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - iio: adc: ti-ads124s08: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - Bluetooth: Remove debugfs directory on module init failure
+    - Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001
+    - xhci: Fix incorrect stream context type macro
+    - xhci: Mitigate failed set dequeue pointer commands
+    - USB: serial: option: add support for Quectel EG916Q-GL
+    - USB: serial: option: add Telit FN920C04 MBIM compositions
+    - parport: Proper fix for array out-of-bounds access
+    - x86/resctrl: Annotate get_mem_config() functions as __init
+    - x86/apic: Always explicitly disarm TSC-deadline timer
+    - x86/entry_32: Do not clobber user EFLAGS.ZF
+    - x86/entry_32: Clear CPU buffers after register restore in NMI return
+    - pinctrl: ocelot: fix system hang on level based interrupts
+    - irqchip/gic-v4: Don't allow a VMOVP on a dying VPE
+    - mptcp: track and update contiguous data status
+    - mptcp: handle consistently DSS corruption
+    - tcp: fix mptcp DSS corruption due to large pmtu xmit
+    - mptcp: fallback when MPTCP opts are dropped after 1st data
+    - mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow
+    - mptcp: prevent MPC handshake on port-based signal endpoints
+    - nilfs2: propagate directory read errors from nilfs_find_entry()
+    - powerpc/mm: Always update max/min_low_pfn in mem_topology_setup()
+    - ALSA: hda/conexant - Use cached pin control for Node 0x1d on HP EliteOne
+      1000 G2
+    - Linux 5.15.169
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Mon, 17 Feb 2025 16:56:19 +0800
+
+linux-xilinx-zynqmp (5.15.0-1042.46) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1042.46 -proposed tracker (LP: #2093570)
+
+  * Add list of source files to linux-buildinfo (LP: #2086606)
+    - [Packaging] Add dwarfdump package in the Build-Depends
+
+  [ Ubuntu: 5.15.0-131.141 ]
+
+  * jammy/linux: 5.15.0-131.141 -proposed tracker (LP: #2093573)
+  * CVE-2024-53164
+    - net: sched: fix ordering of qlen adjustment
+  * CVE-2024-53141
+    - netfilter: ipset: add missing range check in bitmap_ip_uadt
+  * CVE-2024-53103
+    - hv_sock: Initializing vsk->trans to NULL to prevent a dangling pointer
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 24 Jan 2025 21:08:48 +0800
+
+linux-xilinx-zynqmp (5.15.0-1041.45) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1041.45 -proposed tracker (LP: #2092128)
+
+  [ Ubuntu: 5.15.0-130.140 ]
+
+  * jammy/linux: 5.15.0-130.140 -proposed tracker (LP: #2092132)
+  * ovs/linuxbridge jobs running on ubuntu jammy broken with latest kernel
+    5.15.0-127.137 (LP: #2091990)
+    - netfilter: xtables: fix typo causing some targets not to load on IPv6
+
+  [ Ubuntu: 5.15.0-128.138 ]
+
+  * jammy/linux: 5.15.0-128.138 -proposed tracker (LP: #2090163)
+  * CVE-2024-50264
+    - vsock/virtio: Initialization of the dangling pointer occurring in vsk->trans
+  * CVE-2024-53057
+    - net/sched: stop qdisc_tree_reduce_backlog on TC_H_ROOT
+  * CVE-2024-43904
+    - drm/amd/display: Add null checks for 'stream' and 'plane' before
+      dereferencing
+  * CVE-2024-40973
+    - media: mtk-vcodec: potential null pointer deference in SCP
+  * CVE-2024-38553
+    - net: fec: remove .ndo_poll_controller to avoid deadlocks
+  * CVE-2024-26822
+    - smb: client: set correct id, uid and cruid for multiuser automounts
+  * CVE-2020-12351 // CVE-2020-12352 // CVE-2020-24490
+    - [Config] Disable BlueZ highspeed support
+  * CVE-2024-40910
+    - ax25: Fix refcount imbalance on inbound connections
+  * CVE-2024-35963
+    - Bluetooth: hci_sock: Fix not validating setsockopt user input
+  * CVE-2024-35965
+    - Bluetooth: L2CAP: Fix not validating setsockopt user input
+  * CVE-2024-35966
+    - Bluetooth: RFCOMM: Fix not validating setsockopt user input
+  * CVE-2024-35967
+    - Bluetooth: SCO: Fix not validating setsockopt user input
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 20 Dec 2024 11:23:20 +0800
+
+linux-xilinx-zynqmp (5.15.0-1039.43) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1039.43 -proposed tracker
+    (LP: #2086354)
+
+  [ Ubuntu: 5.15.0-127.137 ]
+
+  * jammy/linux: 5.15.0-127.137 -proposed tracker (LP: #2086357)
+  * Jammy update: v5.15.168 upstream stable release (LP: #2086242)
+    - parisc: Fix 64-bit userspace syscall path
+    - parisc: Fix stack start for ADDR_NO_RANDOMIZE personality
+    - of/irq: Support #msi-cells=<0> in of_msi_get_domain
+    - drm: omapdrm: Add missing check for alloc_ordered_workqueue
+    - jbd2: stop waiting for space when jbd2_cleanup_journal_tail() returns error
+    - jbd2: correctly compare tids with tid_geq function in jbd2_fc_begin_commit
+    - mm: krealloc: consider spare memory for __GFP_ZERO
+    - ocfs2: fix the la space leak when unmounting an ocfs2 volume
+    - ocfs2: fix uninit-value in ocfs2_get_block()
+    - ocfs2: reserve space for inline xattr before attaching reflink tree
+    - ocfs2: cancel dqi_sync_work before freeing oinfo
+    - ocfs2: remove unreasonable unlock in ocfs2_read_blocks
+    - ocfs2: fix null-ptr-deref when journal load failed.
+    - ocfs2: fix possible null-ptr-deref in ocfs2_set_buffer_uptodate
+    - usbnet: ipheth: fix carrier detection in modes 1 and 4
+    - net: ethernet: use ip_hdrlen() instead of bit shift
+    - net: phy: vitesse: repair vsc73xx autonegotiation
+    - powerpc/mm: Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL
+    - btrfs: update target inode's ctime on unlink
+    - Input: ads7846 - ratelimit the spi_sync error message
+    - Input: synaptics - enable SMBus for HP Elitebook 840 G2
+    - HID: multitouch: Add support for GT7868Q
+    - scripts: kconfig: merge_config: config files: add a trailing newline
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Go 3
+    - drm/msm/adreno: Fix error return if missing firmware-name
+    - Input: i8042 - add Fujitsu Lifebook E756 to i8042 quirk table
+    - NFSv4: Fix clearing of layout segments in layoutreturn
+    - NFS: Avoid unnecessary rescanning of the per-server delegation list
+    - platform/x86: panasonic-laptop: Fix SINF array out of bounds accesses
+    - platform/x86: panasonic-laptop: Allocate 1 entry extra in the sinf array
+    - mptcp: pm: Fix uaf in __timer_delete_sync
+    - arm64: dts: rockchip: override BIOS_DISABLE signal via GPIO hog on RK3399
+      Puma
+    - minmax: reduce min/max macro expansion in atomisp driver
+    - net: tighten bad gso csum offset check in virtio_net_hdr
+    - mm: avoid leaving partial pfn mappings around in error case
+    - fs/ntfs3: Use kvfree to free memory allocated by kvmalloc
+    - arm64: dts: rockchip: fix PMIC interrupt pin in pinctrl for ROCK Pi E
+    - eeprom: digsy_mtc: Fix 93xx46 driver probe failure
+    - selftests/bpf: Support SOCK_STREAM in unix_inet_redir_to_connected()
+    - hwmon: (pmbus) Introduce and use write_byte_data callback
+    - hwmon: (pmbus) Conditionally clear individual status bits for pmbus rev >=
+      1.2
+    - ice: fix accounting for filters shared by multiple VSIs
+    - igb: Always call igb_xdp_ring_update_tail() under Tx lock
+    - net/mlx5e: Add missing link modes to ptys2ethtool_map
+    - net/mlx5: Explicitly set scheduling element and TSAR type
+    - net/mlx5: Add support to create match definer
+    - net/mlx5: Add IFC bits and enums for flow meter
+    - net/mlx5: Add missing masks and QoS bit masks for scheduling elements
+    - fou: fix initialization of grc
+    - octeontx2-af: Set XOFF on other child transmit schedulers during SMQ flush
+    - octeontx2-af: Modify SMQ flush sequence to drop packets
+    - net: ftgmac100: Enable TX interrupt to avoid TX timeout
+    - netfilter: nft_socket: fix sk refcount leaks
+    - net: dpaa: Pad packets to ETH_ZLEN
+    - spi: nxp-fspi: fix the KASAN report out-of-bounds bug
+    - dma-buf: heaps: Fix off-by-one in CMA heap fault handler
+    - ASoC: meson: axg-card: fix 'use-after-free'
+    - ASoC: allow module autoloading for table db1200_pids
+    - ALSA: hda/realtek - Fixed ALC256 headphone no sound
+    - ALSA: hda/realtek - FIxed ALC285 headphone no sound
+    - scsi: lpfc: Fix overflow build issue
+    - pinctrl: at91: make it work with current gpiolib
+    - microblaze: don't treat zero reserved memory regions as error
+    - net: ftgmac100: Ensure tx descriptor updates are visible
+    - wifi: iwlwifi: lower message level for FW buffer destination
+    - wifi: iwlwifi: mvm: fix iwl_mvm_scan_fits() calculation
+    - wifi: iwlwifi: mvm: pause TCM when the firmware is stopped
+    - wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead
+    - wifi: iwlwifi: clear trans->state earlier upon error
+    - ASoC: intel: fix module autoloading
+    - ASoC: tda7419: fix module autoloading
+    - spi: spidev: Add an entry for elgin,jg10309-01
+    - drm: komeda: Fix an issue related to normalized zpos
+    - spi: bcm63xx: Enable module autoloading
+    - x86/hyperv: Set X86_FEATURE_TSC_KNOWN_FREQ when Hyper-V provides frequency
+    - spi: spidev: Add missing spi_device_id for jg10309-01
+    - ocfs2: add bounds checking to ocfs2_xattr_find_entry()
+    - ocfs2: strict bound check before memcmp in ocfs2_xattr_find_entry()
+    - cgroup: Make operations on the cgroup root_list RCU safe
+    - Revert "wifi: cfg80211: check wiphy mutex is held for wdev mutex"
+    - gpio: prevent potential speculation leaks in gpio_device_get_desc()
+    - gpiolib: cdev: Ignore reconfiguration without direction
+    - cgroup: Move rcu_head up near the top of cgroup_root
+    - USB: serial: pl2303: add device id for Macrosilicon MS3020
+    - USB: usbtmc: prevent kernel-usb-infoleak
+    - EDAC/synopsys: Add support for version 3 of the Synopsys EDAC DDR
+    - EDAC/synopsys: Use the correct register to disable the error interrupt on v3
+      hw
+    - EDAC/synopsys: Re-enable the error interrupts on v3 hw
+    - EDAC/synopsys: Fix ECC status and IRQ control race condition
+    - EDAC/synopsys: Fix error injection on Zynq UltraScale+
+    - wifi: rtw88: always wait for both firmware loading attempts
+    - crypto: xor - fix template benchmarking
+    - ACPI: PMIC: Remove unneeded check in tps68470_pmic_opregion_probe()
+    - wifi: ath9k: fix parameter check in ath9k_init_debug()
+    - wifi: ath9k: Remove error checks when creating debugfs entries
+    - net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
+    - wifi: rtw88: remove CPT execution branch never used
+    - fs: explicitly unregister per-superblock BDIs
+    - mount: warn only once about timestamp range expiration
+    - fs/namespace: fnic: Switch to use %ptTd
+    - mount: handle OOM on mnt_warn_timestamp_expiry
+    - wifi: iwlwifi: mvm: increase the time between ranging measurements
+    - padata: Honor the caller's alignment in case of chunk_size 0
+    - can: j1939: use correct function name in comment
+    - ACPI: CPPC: Fix MASK_VAL() usage
+    - netfilter: nf_tables: elements with timeout below CONFIG_HZ never expire
+    - netfilter: nf_tables: reject element expiration with no timeout
+    - netfilter: nf_tables: reject expiration higher than timeout
+    - netfilter: nf_tables: remove annotation to access set timeout while holding
+      lock
+    - cpufreq: ti-cpufreq: Introduce quirks to handle syscon fails appropriately
+    - x86/sgx: Fix deadlock in SGX NUMA node search
+    - wifi: cfg80211: fix UBSAN noise in cfg80211_wext_siwscan()
+    - wifi: mt76: mt7915: fix rx filter setting for bfee functionality
+    - wifi: cfg80211: fix two more possible UBSAN-detected off-by-one errors
+    - wifi: mac80211: use two-phase skb reclamation in ieee80211_do_stop()
+    - wifi: wilc1000: fix potential RCU dereference issue in
+      wilc_parse_join_bss_param
+    - sock_map: Add a cond_resched() in sock_hash_free()
+    - can: bcm: Clear bo->bcm_proc_read after remove_proc_entry().
+    - can: m_can: m_can_close(): stop clocks after device has been shut down
+    - Bluetooth: btusb: Fix not handling ZPL/short-transfer
+    - bareudp: Pull inner IP header in bareudp_udp_encap_recv().
+    - net: geneve: support IPv4/IPv6 as inner protocol
+    - geneve: Fix incorrect inner network header offset when innerprotoinherit is
+      set
+    - bareudp: Pull inner IP header on xmit.
+    - net: enetc: Use IRQF_NO_AUTOEN flag in request_irq()
+    - r8169: disable ALDPS per default for RTL8125
+    - net: ipv6: rpl_iptunnel: Fix memory leak in rpl_input
+    - net: tipc: avoid possible garbage value
+    - block, bfq: fix possible UAF for bfqq->bic with merge chain
+    - block, bfq: choose the last bfqq from merge chain in bfq_setup_cooperator()
+    - block, bfq: don't break merge chain in bfq_split_bfqq()
+    - block: print symbolic error name instead of error code
+    - block: fix potential invalid pointer dereference in blk_add_partition
+    - spi: ppc4xx: handle irq_of_parse_and_map() errors
+    - spi: ppc4xx: Avoid returning 0 when failed to parse and map IRQ
+    - arm64: dts: renesas: r9a07g044: Correct GICD and GICR sizes
+    - ARM: dts: microchip: sam9x60: Fix rtc/rtt clocks
+    - ARM: dts: imx7d-zii-rmu2: fix Ethernet PHY pinctrl property
+    - ARM: versatile: fix OF node leak in CPUs prepare
+    - reset: berlin: fix OF node leak in probe() error path
+    - reset: k210: fix OF node leak in probe() error path
+    - clocksource/drivers/qcom: Add missing iounmap() on errors in
+      msm_dt_timer_init()
+    - m68k: Fix kernel_clone_args.flags in m68k_clone()
+    - hwmon: (max16065) Fix overflows seen when writing limits
+    - i2c: Add i2c_get_match_data()
+    - hwmon: (max16065) Remove use of i2c_match_id()
+    - hwmon: (max16065) Fix alarm attributes
+    - mtd: slram: insert break after errors in parsing the map
+    - hwmon: (ntc_thermistor) fix module autoloading
+    - power: supply: axp20x_battery: Remove design from min and max voltage
+    - power: supply: max17042_battery: Fix SOC threshold calc w/ no current sense
+    - fbdev: hpfb: Fix an error handling path in hpfb_dio_probe()
+    - mtd: powernv: Add check devm_kasprintf() returned value
+    - pmdomain: core: Harden inter-column space in debug summary
+    - drm/stm: Fix an error handling path in stm_drm_platform_probe()
+    - drm/amd/display: Add null check for set_output_gamma in
+      dcn30_set_output_transfer_func
+    - drm/amdgpu: Replace one-element array with flexible-array member
+    - drm/amdgpu: properly handle vbios fake edid sizing
+    - drm/radeon: Replace one-element array with flexible-array member
+    - drm/radeon: properly handle vbios fake edid sizing
+    - scsi: NCR5380: Add SCp members to struct NCR5380_cmd
+    - scsi: NCR5380: Check for phase match during PDMA fixup
+    - drm/rockchip: vop: Allow 4096px width scaling
+    - drm/rockchip: dw_hdmi: Fix reading EDID when using a forced mode
+    - drm/radeon/evergreen_cs: fix int overflow errors in cs track offsets
+    - drm/bridge: lontium-lt8912b: Validate mode in drm_bridge_funcs::mode_valid()
+    - scsi: elx: libefc: Fix potential use after free in efc_nport_vport_del()
+    - jfs: fix out-of-bounds in dbNextAG() and diAlloc()
+    - drm/mediatek: Use spin_lock_irqsave() for CRTC event lock
+    - powerpc/32: Remove the 'nobats' kernel parameter
+    - powerpc/32: Remove 'noltlbs' kernel parameter
+    - powerpc/8xx: Fix initial memory mapping
+    - powerpc/8xx: Fix kernel vs user address comparison
+    - drm/msm: Fix incorrect file name output in adreno_request_fw()
+    - drm/msm/a5xx: disable preemption in submits by default
+    - drm/msm/a5xx: properly clear preemption records on resume
+    - drm/msm/a5xx: fix races in preemption evaluation stage
+    - drm/msm: Drop priv->lastctx
+    - drm/msm/a5xx: workaround early ring-buffer emptiness check
+    - ipmi: docs: don't advertise deprecated sysfs entries
+    - drm/msm: fix %s null argument error
+    - drivers:drm:exynos_drm_gsc:Fix wrong assignment in gsc_bind()
+    - xen: use correct end address of kernel for conflict checking
+    - xen/swiotlb: add alignment check for dma buffers
+    - tpm: Clean up TPM space after command failure
+    - selftests/bpf: Fix compile error from rlim_t in sk_storage_map.c
+    - selftests/bpf: Fix error compiling bpf_iter_setsockopt.c with musl libc
+    - selftests/bpf: Fix missing ARRAY_SIZE() definition in bench.c
+    - selftests/bpf: Fix compiling kfree_skb.c with musl-libc
+    - selftests/bpf: Fix compiling flow_dissector.c with musl-libc
+    - selftests/bpf: Fix compiling tcp_rtt.c with musl-libc
+    - selftests/bpf: Fix compiling core_reloc.c with musl-libc
+    - selftests/bpf: Fix errors compiling cg_storage_multi.h with musl libc
+    - selftests/bpf: Fix error compiling test_lru_map.c
+    - selftests/bpf: Fix C++ compile error from missing _Bool type
+    - xz: cleanup CRC32 edits from 2018
+    - kthread: fix task state in kthread worker if being frozen
+    - ext4: clear EXT4_GROUP_INFO_WAS_TRIMMED_BIT even mount with discard
+    - smackfs: Use rcu_assign_pointer() to ensure safe assignment in smk_set_cipso
+    - ext4: avoid buffer_head leak in ext4_mark_inode_used()
+    - ext4: avoid potential buffer_head leak in __ext4_new_inode()
+    - ext4: avoid negative min_clusters in find_group_orlov()
+    - ext4: return error on ext4_find_inline_entry
+    - ext4: avoid OOB when system.data xattr changes underneath the filesystem
+    - nilfs2: fix potential null-ptr-deref in nilfs_btree_insert()
+    - nilfs2: determine empty node blocks as corrupted
+    - nilfs2: fix potential oob read in nilfs_btree_check_delete()
+    - bpf: Fix bpf_strtol and bpf_strtoul helpers for 32bit
+    - perf mem: Free the allocated sort string, fixing a leak
+    - perf sched timehist: Fix missing free of session in perf_sched__timehist()
+    - perf sched timehist: Fixed timestamp error when unable to confirm event
+      sched_in time
+    - perf time-utils: Fix 32-bit nsec parsing
+    - clk: imx: imx8mp: fix clock tree update of TF-A managed clocks
+    - clk: imx: imx8qxp: Register dc0_bypass0_clk before disp clk
+    - clk: imx: imx8qxp: Parent should be initialized earlier than the clock
+    - remoteproc: imx_rproc: Correct ddr alias for i.MX8M
+    - remoteproc: imx_rproc: Initialize workqueue earlier
+    - clk: rockchip: Set parent rate for DCLK_VOP clock on RK3228
+    - Input: ilitek_ts_i2c - avoid wrong input subsystem sync
+    - Input: ilitek_ts_i2c - add report id message validation
+    - drivers: media: dvb-frontends/rtl2832: fix an out-of-bounds write error
+    - drivers: media: dvb-frontends/rtl2830: fix an out-of-bounds write error
+    - PCI: keystone: Fix if-statement expression in ks_pcie_quirk()
+    - PCI: xilinx-nwl: Fix register misspelling
+    - PCI: xilinx-nwl: Clean up clock on probe failure/removal
+    - RDMA/iwcm: Fix WARNING:at_kernel/workqueue.c:#check_flush_dependency
+    - pinctrl: single: fix missing error code in pcs_probe()
+    - RDMA/rtrs: Reset hb_missed_cnt after receiving other traffic from peer
+    - RDMA/rtrs-clt: Reset cid to con_num - 1 to stay in bounds
+    - clk: ti: dra7-atl: Fix leak of of_nodes
+    - nfsd: remove unneeded EEXIST error check in nfsd_do_file_acquire
+    - nfsd: fix refcount leak when file is unhashed after being found
+    - pinctrl: mvebu: Use devm_platform_get_and_ioremap_resource()
+    - pinctrl: mvebu: Fix devinit_dove_pinctrl_probe function
+    - IB/core: Fix ib_cache_setup_one error flow cleanup
+    - watchdog: imx_sc_wdt: Don't disable WDT in suspend
+    - RDMA/hns: Don't modify rq next block addr in HIP09 QPC
+    - RDMA/hns: Fix the overflow risk of hem_list_calc_ba_range()
+    - RDMA/hns: Fix spin_unlock_irqrestore() called with IRQs enabled
+    - RDMA/hns: Remove unused abnormal interrupt of type RAS
+    - RDMA/hns: Fix the wrong type of return value of the interrupt handler
+    - RDMA/hns: Refactor the abnormal interrupt handler function
+    - RDMA/hns: Fix VF triggering PF reset in abnormal interrupt handler
+    - RDMA/hns: Optimize hem allocation performance
+    - riscv: Fix fp alignment bug in perf_callchain_user()
+    - RDMA/cxgb4: Added NULL check for lookup_atid
+    - RDMA/irdma: fix error message in irdma_modify_qp_roce()
+    - ntb: intel: Fix the NULL vs IS_ERR() bug for debugfs_create_dir()
+    - ntb_perf: Fix printk format
+    - nfsd: call cache_put if xdr_reserve_space returns NULL
+    - nfsd: return -EINVAL when namelen is 0
+    - f2fs: fix typo
+    - f2fs: fix to update i_ctime in __f2fs_setxattr()
+    - f2fs: remove unneeded check condition in __f2fs_setxattr()
+    - f2fs: reduce expensive checkpoint trigger frequency
+    - f2fs: optimize error handling in redirty_blocks
+    - f2fs: fix to wait page writeback before setting gcing flag
+    - f2fs: introduce F2FS_IPU_HONOR_OPU_WRITE ipu policy
+    - f2fs: clean up w/ dotdot_name
+    - f2fs: get rid of online repaire on corrupted directory
+    - spi: lpspi: Silence error message upon deferred probe
+    - spi: lpspi: release requested DMA channels
+    - spi: spi-fsl-lpspi: Undo runtime PM changes at driver exit time
+    - iio: adc: ad7606: fix oversampling gpio array
+    - iio: adc: ad7606: fix standby gpio state to match the documentation
+    - coresight: tmc: sg: Do not leak sg_table
+    - interconnect: qcom: sm8250: Enable sync_state
+    - vdpa: Add eventfd for the vdpa callback
+    - vhost_vdpa: assign irq bypass producer token correctly
+    - Revert "dm: requeue IO if mapping table not yet available"
+    - net: axienet: Clean up device used for DMA calls
+    - net: axienet: Clean up DMA start/stop and error handling
+    - net: axienet: don't set IRQ timer when IRQ delay not used
+    - net: axienet: implement NAPI and GRO receive
+    - net: axienet: reduce default RX interrupt threshold to 1
+    - net: axienet: add coalesce timer ethtool configuration
+    - net: axienet: Be more careful about updating tx_bd_tail
+    - net: axienet: Use NAPI for TX completion path
+    - net: axienet: Switch to 64-bit RX/TX statistics
+    - net: xilinx: axienet: Fix packet counting
+    - netfilter: nf_reject_ipv6: fix nf_reject_ip6_tcphdr_put()
+    - net: seeq: Fix use after free vulnerability in ether3 Driver Due to Race
+      Condition
+    - net: ipv6: select DST_CACHE from IPV6_RPL_LWTUNNEL
+    - tcp: check skb is non-NULL in tcp_rto_delta_us()
+    - net: qrtr: Update packets cloning when broadcasting
+    - bonding: Fix unnecessary warnings and logs from bond_xdp_get_xmit_slave()
+    - netfilter: nf_tables: Keep deleted flowtable hooks until after RCU
+    - netfilter: ctnetlink: compile ctnetlink_label_size with
+      CONFIG_NF_CONNTRACK_EVENTS
+    - drm/amd/display: Fix Synaptics Cascaded Panamera DSC Determination
+    - Input: goodix - use the new soc_intel_is_byt() helper
+    - powercap: RAPL: fix invalid initialization for pl4_supported field
+    - x86/mm: Switch to new Intel CPU model defines
+    - vfio/pci: fix potential memory leak in vfio_intx_enable()
+    - selinux,smack: don't bypass permissions check in inode_setsecctx hook
+    - Remove *.orig pattern from .gitignore
+    - PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
+    - ASoC: rt5682: Return devm_of_clk_add_hw_provider to transfer the error
+    - soc: versatile: integrator: fix OF node leak in probe() error path
+    - Revert "media: tuners: fix error return code of
+      hybrid_tuner_request_state()"
+    - Input: i8042 - add TUXEDO Stellaris 16 Gen5 AMD to i8042 quirk table
+    - Input: i8042 - add TUXEDO Stellaris 15 Slim Gen6 AMD to i8042 quirk table
+    - Input: i8042 - add another board name for TUXEDO Stellaris Gen5 AMD line
+    - drm/amd/display: Round calculated vtotal
+    - drm/amd/display: Validate backlight caps are sane
+    - scsi: mac_scsi: Revise printk(KERN_DEBUG ...) messages
+    - scsi: mac_scsi: Refactor polling loop
+    - scsi: mac_scsi: Disallow bus errors during PDMA send
+    - usbnet: fix cyclical race on disconnect with work queue
+    - USB: appledisplay: close race between probe and completion handler
+    - USB: misc: cypress_cy7c63: check for short transfer
+    - USB: class: CDC-ACM: fix race between get_serial and set_serial
+    - usb: cdnsp: Fix incorrect usb_request status
+    - usb: dwc2: drd: fix clock gating on USB role switch
+    - bus: integrator-lm: fix OF node leak in probe()
+    - firmware_loader: Block path traversal
+    - tty: rp2: Fix reset with non forgiving PCIe host bridges
+    - xhci: Set quirky xHC PCI hosts to D3 _after_ stopping and freeing them.
+    - crypto: ccp - Properly unregister /dev/sev on sev PLATFORM_STATUS failure
+    - drbd: Fix atomicity violation in drbd_uuid_set_bm()
+    - drbd: Add NULL check for net_conf to prevent dereference in state validation
+    - ACPI: sysfs: validate return type of _STR method
+    - ACPI: resource: Add another DMI match for the TongFang GMxXGxx
+    - efistub/tpm: Use ACPI reclaim memory for event log to avoid corruption
+    - perf/x86/intel/pt: Fix sampling synchronization
+    - wifi: rtw88: 8822c: Fix reported RX band width
+    - wifi: mt76: mt7615: check devm_kasprintf() returned value
+    - debugobjects: Fix conditions in fill_pool()
+    - f2fs: prevent possible int overflow in dir_block_index()
+    - f2fs: avoid potential int overflow in sanity_check_area_boundary()
+    - hwrng: mtk - Use devm_pm_runtime_enable
+    - hwrng: bcm2835 - Add missing clk_disable_unprepare in bcm2835_rng_init
+    - hwrng: cctrng - Add missing clk_disable_unprepare in cctrng_resume
+    - arm64: dts: rockchip: Raise Pinebook Pro's panel backlight PWM frequency
+    - arm64: dts: rockchip: Correct the Pinebook Pro battery design capacity
+    - vfs: fix race between evice_inodes() and find_inode()&iput()
+    - fs: Fix file_set_fowner LSM hook inconsistencies
+    - nfs: fix memory leak in error path of nfs4_do_reclaim
+    - EDAC/igen6: Fix conversion of system address to physical memory address
+    - padata: use integer wrap around to prevent deadlock on seq_nr overflow
+    - soc: versatile: realview: fix memory leak during device remove
+    - soc: versatile: realview: fix soc_dev leak during device remove
+    - usb: yurex: Replace snprintf() with the safer scnprintf() variant
+    - USB: misc: yurex: fix race between read and write
+    - xhci: fix event ring segment table related masks and variables in header
+    - xhci: remove xhci_test_trb_in_td_math early development check
+    - xhci: Refactor interrupter code for initial multi interrupter support.
+    - xhci: Preserve RsvdP bits in ERSTBA register correctly
+    - xhci: Add a quirk for writing ERST in high-low order
+    - usb: xhci: fix loss of data on Cadence xHC
+    - pps: remove usage of the deprecated ida_simple_xx() API
+    - pps: add an error check in parport_attach
+    - x86/idtentry: Incorporate definitions/declarations of the FRED entries
+    - x86/entry: Remove unwanted instrumentation in common_interrupt()
+    - bpf: lsm: Set bpf_lsm_blob_sizes.lbs_task to 0
+    - lockdep: fix deadlock issue between lockdep and rcu
+    - mm: only enforce minimum stack gap size if it's sensible
+    - i2c: aspeed: Update the stop sw state when the bus recovery occurs
+    - i2c: isch: Add missed 'else'
+    - usb: yurex: Fix inconsistent locking bug in yurex_read()
+    - spi: lpspi: Simplify some error message
+    - static_call: Handle module init failure correctly in
+      static_call_del_module()
+    - static_call: Replace pointless WARN_ON() in static_call_module_notify()
+    - mailbox: rockchip: fix a typo in module autoloading
+    - mailbox: bcm2835: Fix timeout during suspend mode
+    - ceph: remove the incorrect Fw reference check when dirtying pages
+    - ieee802154: Fix build error
+    - net/mlx5: Fix error path in multi-packet WQE transmit
+    - net/mlx5: Added cond_resched() to crdump collection
+    - net/mlx5e: Fix NULL deref in mlx5e_tir_builder_alloc()
+    - netfilter: uapi: NFTA_FLOWTABLE_HOOK is NLA_NESTED
+    - net: ieee802154: mcr20a: Use IRQF_NO_AUTOEN flag in request_irq()
+    - netfilter: nf_tables: prevent nf_skb_duplicated corruption
+    - Bluetooth: btmrvl: Use IRQF_NO_AUTOEN flag in request_irq()
+    - net: ethernet: lantiq_etop: fix memory disclosure
+    - net: avoid potential underflow in qdisc_pkt_len_init() with UFO
+    - net: add more sanity checks to qdisc_pkt_len_init()
+    - stmmac_pci: Fix underflow size in stmmac_rx
+    - net: stmmac: Disable automatic FCS/Pad stripping
+    - net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check
+    - ipv4: ip_gre: Fix drops of small packets in ipgre_xmit
+    - ppp: do not assume bh is held in ppp_channel_bridge_input()
+    - sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
+    - i2c: xiic: Fix broken locking on tx_msg
+    - i2c: xiic: Switch from waitqueue to completion
+    - i2c: xiic: Fix RX IRQ busy check
+    - i2c: xiic: xiic_xfer(): Fix runtime PM leak on error path
+    - i2c: xiic: improve error message when transfer fails to start
+    - i2c: xiic: Try re-initialization on bus busy timeout
+    - media: usbtv: Remove useless locks in usbtv_video_free()
+    - ALSA: mixer_oss: Remove some incorrect kfree_const() usages
+    - ALSA: hda/realtek: Fix the push button function for the ALC257
+    - ALSA: hda/generic: Unconditionally prefer preferred_dacs pairs
+    - ASoC: imx-card: Set card.owner to avoid a warning calltrace if SND=m
+    - ALSA: hda/conexant: Fix conflicting quirk for System76 Pangolin
+    - f2fs: Require FMODE_WRITE for atomic write ioctls
+    - wifi: ath9k: fix possible integer overflow in ath9k_get_et_stats()
+    - wifi: ath9k_htc: Use __skb_set_length() for resetting urb before resubmit
+    - ice: Adjust over allocation of memory in ice_sched_add_root_node() and
+      ice_sched_add_node()
+    - net/xen-netback: prevent UAF in xenvif_flush_hash()
+    - net: hisilicon: hip04: fix OF node leak in probe()
+    - net: hisilicon: hns_dsaf_mac: fix OF node leak in hns_mac_get_info()
+    - net: hisilicon: hns_mdio: fix OF node leak in probe()
+    - ACPI: PAD: fix crash in exit_round_robin()
+    - ACPICA: Fix memory leak if acpi_ps_get_next_namepath() fails
+    - ACPICA: Fix memory leak if acpi_ps_get_next_field() fails
+    - net: sched: consistently use rcu_replace_pointer() in taprio_change()
+    - blk_iocost: fix more out of bound shifts
+    - nvme-pci: qdepth 1 quirk
+    - wifi: ath11k: fix array out-of-bound access in SoC stats
+    - wifi: rtw88: select WANT_DEV_COREDUMP
+    - ACPI: EC: Do not release locks during operation region accesses
+    - ACPICA: check null return of ACPI_ALLOCATE_ZEROED() in
+      acpi_db_convert_to_package()
+    - tipc: guard against string buffer overrun
+    - net: mvpp2: Increase size of queue_name buffer
+    - ipv4: Check !in_dev earlier for ioctl(SIOCSIFADDR).
+    - ipv4: Mask upper DSCP bits and ECN bits in NETLINK_FIB_LOOKUP family
+    - net: atlantic: Avoid warning about potential string truncation
+    - tcp: avoid reusing FIN_WAIT2 when trying to find port in connect() process
+    - ACPICA: iasl: handle empty connection_node
+    - proc: add config & param to block forcing mem writes
+    - [Config] updateconfigs to select PROC_MEM_ALWAYS_FORCE
+    - wifi: mt76: mt7915: hold dev->mt76.mutex while disabling tx worker
+    - wifi: mwifiex: Fix memcpy() field-spanning write warning in
+      mwifiex_cmd_802_11_scan_ext()
+    - nfp: Use IRQF_NO_AUTOEN flag in request_irq()
+    - signal: Replace BUG_ON()s
+    - ALSA: usb-audio: Add input value sanity checks for standard types
+    - x86/ioapic: Handle allocation failures gracefully
+    - ALSA: usb-audio: Define macros for quirk table entries
+    - ALSA: usb-audio: Add logitech Audio profile quirk
+    - tools/x86/kcpuid: Protect against faulty "max subleaf" values
+    - ALSA: asihpi: Fix potential OOB array access
+    - ALSA: hdsp: Break infinite MIDI input flush loop
+    - x86/syscall: Avoid memcpy() for ia32 syscall_get_arguments()
+    - fbdev: pxafb: Fix possible use after free in pxafb_task()
+    - rcuscale: Provide clear error when async specified without primitives
+    - iommu/arm-smmu-qcom: hide last LPASS SMMU context bank from linux
+    - power: reset: brcmstb: Do not go into infinite loop if reset fails
+    - iommu/vt-d: Always reserve a domain ID for identity setup
+    - iommu/vt-d: Fix potential lockup if qi_submit_sync called with 0 count
+    - drm/amd/display: Add null check for top_pipe_to_program in
+      commit_planes_for_stream
+    - ata: sata_sil: Rename sil_blacklist to sil_quirks
+    - drm/amd/display: Check null pointers before using dc->clk_mgr
+    - jfs: UBSAN: shift-out-of-bounds in dbFindBits
+    - jfs: Fix uaf in dbFreeBits
+    - jfs: check if leafidx greater than num leaves per dmap tree
+    - scsi: smartpqi: correct stream detection
+    - jfs: Fix uninit-value access of new_ea in ea_buffer
+    - drm/amdgpu: add raven1 gfxoff quirk
+    - drm/amdgpu: enable gfxoff quirk on HP 705G4
+    - HID: multitouch: Add support for Thinkpad X12 Gen 2 Kbd Portfolio
+    - platform/x86: touchscreen_dmi: add nanote-next quirk
+    - drm/amd/display: Check stream before comparing them
+    - drm/amd/display: Fix index out of bounds in DCN30 degamma hardware format
+      translation
+    - drm/amd/display: Fix index out of bounds in degamma hardware format
+      translation
+    - drm/amd/display: Fix index out of bounds in DCN30 color transformation
+    - drm/amd/display: Initialize get_bytes_per_element's default to 1
+    - drm/printer: Allow NULL data in devcoredump printer
+    - scsi: aacraid: Rearrange order of struct aac_srb_unit
+    - drm/radeon/r100: Handle unknown family in r100_cp_init_microcode()
+    - drm/amd/pm: ensure the fw_info is not null before using it
+    - of/irq: Refer to actual buffer size in of_irq_parse_one()
+    - ext4: ext4_search_dir should return a proper error
+    - ext4: avoid use-after-free in ext4_ext_show_leaf()
+    - ext4: fix i_data_sem unlock order in ext4_ind_migrate()
+    - blk-integrity: use sysfs_emit
+    - blk-integrity: convert to struct device_attribute
+    - blk-integrity: register sysfs attributes on struct device
+    - usb: typec: tcpm: Check for port partner validity before consuming it
+    - spi: spi-imx: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - spi: s3c64xx: fix timeout counters in flush_fifo
+    - selftests: breakpoints: use remaining time to check if suspend succeed
+    - selftests: vDSO: fix vDSO name for powerpc
+    - selftests: vDSO: fix vdso_config for powerpc
+    - selftests: vDSO: fix vDSO symbols lookup for powerpc64
+    - selftests/mm: fix charge_reserved_hugetlb.sh test
+    - selftests: vDSO: fix ELF hash table entry size for s390x
+    - selftests: vDSO: fix vdso_config for s390
+    - platform/x86: ISST: Fix the KASAN report slab-out-of-bounds bug
+    - i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume
+    - i2c: qcom-geni: Use IRQF_NO_AUTOEN flag in request_irq()
+    - i2c: xiic: Wait for TX empty to avoid missed TX NAKs
+    - firmware: tegra: bpmp: Drop unused mbox_client_to_bpmp()
+    - spi: bcm63xx: Fix module autoloading
+    - power: supply: hwmon: Fix missing temp1_max_alarm attribute
+    - perf/core: Fix small negative period being ignored
+    - parisc: Fix itlb miss handler for 64-bit programs
+    - drm: Consistently use struct drm_mode_rect for FB_DAMAGE_CLIPS
+    - ALSA: core: add isascii() check to card ID generator
+    - ALSA: usb-audio: Add delay quirk for VIVO USB-C HEADSET
+    - ALSA: usb-audio: Add native DSD support for Luxman D-08u
+    - ALSA: line6: add hw monitor volume control to POD HD500X
+    - ALSA: hda/realtek: Add quirk for Huawei MateBook 13 KLV-WX9
+    - ext4: no need to continue when the number of entries is 1
+    - ext4: correct encrypted dentry name hash when not casefolded
+    - ext4: fix slab-use-after-free in ext4_split_extent_at()
+    - ext4: propagate errors from ext4_find_extent() in ext4_insert_range()
+    - ext4: fix incorrect tid assumption in __jbd2_log_wait_for_space()
+    - ext4: drop ppath from ext4_ext_replay_update_ex() to avoid double-free
+    - ext4: aovid use-after-free in ext4_ext_insert_extent()
+    - ext4: fix double brelse() the buffer of the extents path
+    - ext4: update orig_path in ext4_find_extent()
+    - ext4: fix incorrect tid assumption in ext4_wait_for_tail_page_commit()
+    - ext4: fix incorrect tid assumption in jbd2_journal_shrink_checkpoint_list()
+    - ext4: fix fast commit inode enqueueing during a full journal commit
+    - ext4: use handle to mark fc as ineligible in __track_dentry_update()
+    - ext4: mark fc as ineligible using an handle in ext4_xattr_set()
+    - riscv: define ILLEGAL_POINTER_VALUE for 64bit
+    - exfat: fix memory leak in exfat_load_bitmap()
+    - perf hist: Update hist symbol when updating maps
+    - nfsd: fix delegation_blocked() to block correctly for at least 30 seconds
+    - nfsd: map the EBADMSG to nfserr_io to avoid warning
+    - NFSD: Fix NFSv4's PUTPUBFH operation
+    - aoe: fix the potential use-after-free problem in more places
+    - clk: rockchip: fix error for unknown clocks
+    - clk: qcom: dispcc-sm8250: use CLK_SET_RATE_PARENT for branch clocks
+    - media: sun4i_csi: Implement link validate for sun4i_csi subdev
+    - media: uapi/linux/cec.h: cec_msg_set_reply_to: zero flags
+    - clk: qcom: clk-rpmh: Fix overflow in BCM vote
+    - clk: qcom: gcc-sm8150: De-register gcc_cpuss_ahb_clk_src
+    - media: venus: fix use after free bug in venus_remove due to race condition
+    - clk: qcom: gcc-sm8250: Do not turn off PCIe GDSCs during gdsc_disable()
+    - clk: qcom: gcc-sc8180x: Fix the sdcc2 and sdcc4 clocks freq table
+    - iio: magnetometer: ak8975: Fix reading for ak099xx sensors
+    - tomoyo: fallback to realpath if symlink's pathname does not exist
+    - net: stmmac: Fix zero-division error when disabling tc cbs
+    - rtc: at91sam9: fix OF node leak in probe() error path
+    - Input: adp5589-keys - fix NULL pointer dereference
+    - Input: adp5589-keys - fix adp5589_gpio_get_value()
+    - ACPI: resource: Add Asus Vivobook X1704VAP to irq1_level_low_skip_override[]
+    - ACPI: resource: Add Asus ExpertBook B2502CVA to
+      irq1_level_low_skip_override[]
+    - btrfs: fix a NULL pointer dereference when failed to start a new trasacntion
+    - btrfs: wait for fixup workers before stopping cleaner kthread during umount
+    - gpio: davinci: fix lazy disable
+    - tracing/hwlat: Fix a race during cpuhp processing
+    - tracing/timerlat: Fix a race during cpuhp processing
+    - close_range(): fix the logics in descriptor table trimming
+    - drm/sched: Add locking to drm_sched_entity_modify_sched
+    - drm/amd/display: Fix system hang while resume with TBT monitor
+    - kconfig: qconf: fix buffer overflow in debug links
+    - device property: Add fwnode_iomap()
+    - device property: Add fwnode_irq_get_byname
+    - i2c: smbus: Use device_*() functions instead of of_*()
+    - i2c: create debugfs entry per adapter
+    - i2c: core: Lock address during client device instantiation
+    - i2c: xiic: Use devm_clk_get_enabled()
+    - i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - spi: bcm63xx: Fix missing pm_runtime_disable()
+    - ext4: properly sync file size update after O_SYNC direct IO
+    - ext4: dax: fix overflowing extents beyond inode size when partially writing
+    - arm64: Add Cortex-715 CPU part definition
+    - arm64: cputype: Add Neoverse-N3 definitions
+    - arm64: errata: Expand speculative SSBS workaround once more
+    - uprobes: fix kernel info leak via "[uprobes]" vma
+    - drm/amd/display: Allow backlight to go below
+      `AMDGPU_DM_DEFAULT_MIN_BACKLIGHT`
+    - build-id: require program headers to be right after ELF header
+    - lib/buildid: harden build ID parsing logic
+    - drm/rockchip: define gamma registers for RK3399
+    - drm/rockchip: support gamma control on RK3399
+    - drm/rockchip: vop: clear DMA stop bit on RK3066
+    - media: i2c: imx335: Enable regulator supplies
+    - media: imx335: Fix reset-gpio handling
+    - dt-bindings: clock: qcom: Add missing UFS QREF clocks
+    - dt-bindings: clock: qcom: Add GPLL9 support on gcc-sc8180x
+    - r8169: Fix spelling mistake: "tx_underun" -> "tx_underrun"
+    - r8169: add tally counter fields added with RTL8125
+    - clk: qcom: gcc-sc8180x: Add GPLL9 support
+    - ACPI: battery: Simplify battery hook locking
+    - ACPI: battery: Fix possible crash when unregistering a battery hook
+    - Revert "arm64: dts: qcom: sm8250: switch UFS QMP PHY to new style of
+      bindings"
+    - ext4: fix inode tree inconsistency caused by ENOMEM
+    - 9p: add missing locking around taking dentry fid list
+    - vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
+    - perf report: Fix segfault when 'sym' sort key is not used
+    - ALSA: usb-audio: Fix possible NULL pointer dereference in
+      snd_usb_pcm_has_fixed_rate()
+    - unicode: Don't special case ignorable code points
+    - net: ethernet: cortina: Drop TSO support
+    - tracing: Remove precision vsnprintf() check from print event
+    - drm/crtc: fix uninitialized variable use even harder
+    - tracing: Have saved_cmdlines arrays all in one allocation
+    - selftests/net: give more time to udpgro bg processes to complete startup
+    - selftests/net: synchronize udpgro tests' tx and rx connection
+    - selftests: net: Remove executable bits from library scripts
+    - fs/ntfs3: Refactor enum_rstbl to suppress static checker
+    - virtio_console: fix misc probe bugs
+    - Input: synaptics-rmi4 - fix UAF of IRQ domain on driver removal
+    - bpf: Check percpu map value size first
+    - s390/facility: Disable compile time optimization for decompressor code
+    - s390/mm: Add cond_resched() to cmm_alloc/free_pages()
+    - bpf, x64: Fix a jit convergence issue
+    - ext4: don't set SB_RDONLY after filesystem errors
+    - ext4: nested locking for xattr inode
+    - s390/cpum_sf: Remove WARN_ON_ONCE statements
+    - ktest.pl: Avoid false positives with grub2 skip regex
+    - RDMA/mad: Improve handling of timed out WRs of mad agent
+    - PCI: Add function 0 DMA alias quirk for Glenfly Arise chip
+    - RDMA/rtrs-srv: Avoid null pointer deref during path establishment
+    - clk: bcm: bcm53573: fix OF node leak in init
+    - PCI: Add ACS quirk for Qualcomm SA8775P
+    - i2c: i801: Use a different adapter-name for IDF adapters
+    - PCI: Mark Creative Labs EMU20k2 INTx masking as broken
+    - ntb: ntb_hw_switchtec: Fix use after free vulnerability in
+      switchtec_ntb_remove due to race condition
+    - media: videobuf2-core: clear memory related fields in
+      __vb2_plane_dmabuf_put()
+    - remoteproc: imx_rproc: Use imx specific hook for find_loaded_rsc_table
+    - clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D
+    - usb: chipidea: udc: enable suspend interrupt after usb reset
+    - usb: dwc2: Adjust the timing of USB Driver Interrupt Registration in the
+      Crashkernel Scenario
+    - comedi: ni_routing: tools: Check when the file could not be opened
+    - virtio_pmem: Check device status before requesting flush
+    - tools/iio: Add memory allocation failure check for trigger_name
+    - driver core: bus: Return -EIO instead of 0 when show/store invalid bus
+      attribute
+    - drm/amd/display: Check null pointer before dereferencing se
+    - fbdev: sisfb: Fix strbuf array overflow
+    - RDMA/rxe: Fix seg fault in rxe_comp_queue_pkt
+    - NFSD: Mark filecache "down" if init fails
+    - ice: fix VLAN replay after reset
+    - SUNRPC: Fix integer overflow in decode_rc_list()
+    - NFSv4: Prevent NULL-pointer dereference in nfs42_complete_copies()
+    - net: phy: dp83869: fix memory corruption when enabling fiber
+    - tcp: fix to allow timestamp undo if no retransmits were sent
+    - tcp: fix tcp_enter_recovery() to zero retrans_stamp when it's safe
+    - netfilter: br_netfilter: fix panic with metadata_dst skb
+    - Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
+    - net: phy: bcm84881: Fix some error handling paths
+    - thermal: int340x: processor_thermal: Set feature mask before
+      proc_thermal_add
+    - thermal: intel: int340x: processor: Fix warning during module unload
+    - net: dsa: b53: fix jumbo frame mtu check
+    - net: dsa: b53: fix max MTU for 1g switches
+    - net: dsa: b53: fix max MTU for BCM5325/BCM5365
+    - net: dsa: b53: allow lower MTUs on BCM5325/5365
+    - net: dsa: b53: fix jumbo frames on 10/100 ports
+    - gpio: aspeed: Add the flush write to ensure the write complete.
+    - gpio: aspeed: Use devm_clk api to manage clock source
+    - ice: Fix netif_is_ice() in Safe Mode
+    - i40e: Fix macvlan leak by synchronizing access to mac_filter_hash
+    - igb: Do not bring the device up after non-fatal error
+    - net/sched: accept TCA_STAB only for root qdisc
+    - net: ibm: emac: mal: fix wrong goto
+    - sctp: ensure sk_state is set to CLOSED if hashing fails in sctp_listen_start
+    - netfilter: xtables: avoid NFPROTO_UNSPEC where needed
+    - net: Add l3mdev index to flow struct and avoid oif reset for port devices
+    - netfilter: rpfilter/fib: Populate flowic_l3mdev field
+    - netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
+    - netfilter: fib: check correct rtable in vrf setups
+    - net: rtnetlink: add msg kind names
+    - rtnetlink: Add bulk registration helpers for rtnetlink message handlers.
+    - mctp: Handle error of rtnl_register_module().
+    - ppp: fix ppp_async_encode() illegal access
+    - slip: make slhc_remember() more robust against malicious packets
+    - RDMA/hns: Fix UAF for cq async event
+    - x86/fpu: Avoid writing LBR bit to IA32_XSS unless supported
+    - hwmon: (tmp513) Add missing dependency on REGMAP_I2C
+    - hwmon: (adm9240) Add missing dependency on REGMAP_I2C
+    - hwmon: (adt7470) Add missing dependency on REGMAP_I2C
+    - HID: amd_sfh: Switch to device-managed dmam_alloc_coherent()
+    - resource: fix region_intersects() vs add_memory_driver_managed()
+    - HID: plantronics: Workaround for an unexcepted opposite volume key
+    - Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
+    - usb: dwc3: core: Stop processing of pending events if controller is halted
+    - usb: xhci: Fix problem with xhci resume from suspend
+    - usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
+    - hid: intel-ish-hid: Fix uninitialized variable 'rv' in
+      ish_fw_xfer_direct_dma
+    - drm/v3d: Stop the active perfmon before being destroyed
+    - net: explicitly clear the sk pointer, when pf->create fails
+    - net: Fix an unsafe loop on the list
+    - net: dsa: lan9303: ensure chip reset and wait for READY status
+    - mptcp: pm: do not remove closing subflows
+    - nouveau/dmem: Fix vulnerability in migrate_to_ram upon copy error
+    - kthread: unpark only parked kthread
+    - block, bfq: fix uaf for accessing waker_bfqq after splitting
+    - i2c: smbus: Check for parent device before dereference
+    - net: geneve: add missing netlink policy and size for
+      IFLA_GENEVE_INNER_PROTO_INHERIT
+    - xfrm: Pass flowi_oif or l3mdev as oif to xfrm_dst_lookup
+    - net: Handle l3mdev in ip_tunnel_init_flow
+    - net: seg6: fix seg6_lookup_any_nexthop() to handle VRFs using flowi_l3mdev
+    - net: vrf: determine the dst using the original ifindex for multicast
+    - netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
+    - ext4: fix warning in ext4_dio_write_end_io()
+    - net: axienet: start napi before enabling Rx/Tx
+    - selftests: net: more strict check in net_helper
+    - net: xilinx: axienet: Schedule NAPI in two steps
+    - Linux 5.15.168
+  * CVE-2024-36968
+    - Bluetooth: L2CAP: Fix div-by-zero in l2cap_le_flowctl_init()
+  * CVE-2024-35904
+    - selinux: avoid dereference of garbage after mount failure
+  * IOMMU warnings on AMD systems after booting into kdump kernel
+    (LP: #2080378)
+    - iommu/amd: Simplify and Consolidate Virtual APIC (AVIC) Enablement
+    - iommu/amd: Fix compile warning in init code
+  * CVE-2024-42156
+    - s390/pkey: Wipe copies of clear-key structures on failure
+  * CVE-2024-44942
+    - f2fs: fix to do sanity check on F2FS_INLINE_DATA flag in inode during GC
+  * CVE-2024-38538
+    - net: bridge: xmit: make sure we have at least eth header len bytes
+  * CVE-2024-42158
+    - s390/pkey: Use kfree_sensitive() to fix Coccinelle warnings
+  * CVE-2024-38667
+    - riscv: prevent pt_regs corruption for secondary idle threads
+  * CVE-2024-44940
+    - fou: remove warn in gue_gro_receive on unsupported protocol
+  * CVE-2024-42079
+    - gfs2: Fix NULL pointer dereference in gfs2_log_flush
+  * CVE-2024-35951
+    - drm/panfrost: Fix the error path in panfrost_mmu_map_fault_addr()
+  * LXD fan bridge causes blocked tasks (LP: #2064176)
+    - SAUCE: fan: release rcu_read_lock on skb discard path
+  * CVE-2023-52532
+    - net: mana: Fix TX CQE error handling
+  * CVE-2023-52621
+    - bpf: Check rcu_read_lock_trace_held() before calling bpf map helpers
+  * CVE-2024-26947
+    - ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses
+  * CVE-2023-52639
+    - KVM: s390: vsie: fix race during shadow creation
+
+  [ Ubuntu: 5.15.0-126.136 ]
+
+  * jammy/linux: 5.15.0-126.136 -proposed tracker (LP: #2086027)
+    - [Packaging] resync git-ubuntu-log
+  * Cannot detect audio sinks and sources in proposed kernel (LP: #2085082)
+    - soundwire: stream: Revert "soundwire: stream: fix programming slave ports
+      for non-continous port maps"
+
+ -- Ubuntu Kernel Preparation Bot <ubuntu-kernel-bot@canonical.com>  Thu, 21 Nov 2024 23:54:48 +0000
+
+linux-xilinx-zynqmp (5.15.0-1038.42) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1038.42 -proposed tracker (LP: #2082998)
+
+  [ Ubuntu: 5.15.0-125.135 ]
+
+  * jammy/linux: 5.15.0-125.135 -proposed tracker (LP: #2083001)
+  * CVE-2024-26800
+    - tls: rx: coalesce exit paths in tls_decrypt_sg()
+    - tls: separate no-async decryption request handling from async
+    - tls: fix use-after-free on failed backlog decryption
+  * Please backport the more restrictive XSAVES deactivation for  Zen1/2 arch
+    (LP: #2077321)
+    - x86/CPU/AMD: Improve the erratum 1386 workaround
+  * Jammy update: v5.15.167 upstream stable release (LP: #2081279)
+    - drm: panel-orientation-quirks: Add quirk for OrangePi Neo
+    - ALSA: hda/generic: Add a helper to mute speakers at suspend/shutdown
+    - ALSA: hda/conexant: Mute speakers at suspend / shutdown
+    - i2c: Fix conditional for substituting empty ACPI functions
+    - dma-debug: avoid deadlock between dma debug vs printk and netconsole
+    - net: usb: qmi_wwan: add MeiG Smart SRM825L
+    - drm/amdgpu: Fix uninitialized variable warning in amdgpu_afmt_acr
+    - drm/amd/display: Assign linear_pitch_alignment even for VM
+    - drm/amdgpu: fix overflowed array index read warning
+    - drm/amdgpu/pm: Check the return value of smum_send_msg_to_smc
+    - drm/amd/pm: fix uninitialized variable warning for smu8_hwmgr
+    - drm/amd/pm: fix warning using uninitialized value of max_vid_step
+    - drm/amd/pm: fix the Out-of-bounds read warning
+    - drm/amdgpu: fix uninitialized scalar variable warning
+    - drm/amd/pm: fix uninitialized variable warnings for vega10_hwmgr
+    - drm/amdgpu: avoid reading vf2pf info size from FB
+    - drm/amd/display: Check gpio_id before used as array index
+    - drm/amd/display: Stop amdgpu_dm initialize when stream nums greater than 6
+    - drm/amd/display: Add array index check for hdcp ddc access
+    - drm/amd/display: Check num_valid_sets before accessing reader_wm_sets[]
+    - drm/amd/display: Check msg_id before processing transcation
+    - drm/amd/display: Fix Coverity INTEGER_OVERFLOW within
+      dal_gpio_service_create
+    - drm/amd/amdgpu: Check tbo resource pointer
+    - drm/amdgpu/pm: Fix uninitialized variable warning for smu10
+    - drm/amdgpu/pm: Fix uninitialized variable agc_btc_response
+    - drm/amdgpu: Fix out-of-bounds write warning
+    - drm/amdgpu: Fix out-of-bounds read of df_v1_7_channel_number
+    - drm/amdgpu: fix ucode out-of-bounds read warning
+    - drm/amdgpu: fix mc_data out-of-bounds read warning
+    - drm/amdkfd: Reconcile the definition and use of oem_id in struct
+      kfd_topology_device
+    - apparmor: fix possible NULL pointer dereference
+    - drm/amdgpu/pm: Check input value for CUSTOM profile mode setting on legacy
+      SOCs
+    - drm/amdgpu: fix the waring dereferencing hive
+    - drm/amd/pm: check specific index for aldebaran
+    - drm/amdgpu: the warning dereferencing obj for nbio_v7_4
+    - drm/amd/pm: check negtive return for table entries
+    - drm/amdgpu: update type of buf size to u32 for eeprom functions
+    - wifi: iwlwifi: remove fw_running op
+    - cpufreq: scmi: Avoid overflow of target_freq in fast switch
+    - PCI: al: Check IORESOURCE_BUS existence during probe
+    - hwspinlock: Introduce hwspin_lock_bust()
+    - RDMA/efa: Properly handle unexpected AQ completions
+    - ionic: fix potential irq name truncation
+    - rcu/nocb: Remove buggy bypass lock contention mitigation
+    - usbip: Don't submit special requests twice
+    - usb: typec: ucsi: Fix null pointer dereference in trace
+    - fsnotify: clear PARENT_WATCHED flags lazily
+    - smack: tcp: ipv4, fix incorrect labeling
+    - drm/meson: plane: Add error handling
+    - drm/bridge: tc358767: Check if fully initialized before signalling HPD event
+      via IRQ
+    - wifi: cfg80211: make hash table duplicates more survivable
+    - block: remove the blk_flush_integrity call in blk_integrity_unregister
+    - drm/amd/display: Skip wbscl_set_scaler_filter if filter is null
+    - media: uvcvideo: Enforce alignment of frame and interval
+    - drm/amd/pm: Fix the null pointer dereference for vega10_hwmgr
+    - virtio_net: Fix napi_skb_cache_put warning
+    - rcu-tasks: Fix show_rcu_tasks_trace_gp_kthread buffer overflow
+    - ext4: reject casefold inode flag without casefold feature
+    - udf: Limit file size to 4TB
+    - ext4: handle redirtying in ext4_bio_write_page()
+    - i2c: Use IS_REACHABLE() for substituting empty ACPI functions
+    - sch/netem: fix use after free in netem_dequeue
+    - ASoC: dapm: Fix UAF for snd_soc_pcm_runtime object
+    - KVM: SVM: fix emulation of msr reads/writes of MSR_FS_BASE and MSR_GS_BASE
+    - KVM: SVM: Don't advertise Bus Lock Detect to guest if SVM support is missing
+    - ALSA: hda/conexant: Add pincfg quirk to enable top speakers on Sirius
+      devices
+    - ALSA: hda/realtek: add patch for internal mic in Lenovo V145
+    - ALSA: hda/realtek: Support mute LED on HP Laptop 14-dq2xxx
+    - ata: libata: Fix memory leak for error path in ata_host_alloc()
+    - irqchip/gic-v2m: Fix refcount leak in gicv2m_of_init()
+    - rtmutex: Drop rt_mutex::wait_lock before scheduling
+    - nvme-pci: Add sleep quirk for Samsung 990 Evo
+    - Revert "Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE"
+    - Bluetooth: MGMT: Ignore keys being loaded with invalid type
+    - mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K
+    - mmc: sdhci-of-aspeed: fix module autoloading
+    - mmc: cqhci: Fix checking of CQHCI_HALT state
+    - fuse: update stats for pages in dropped aux writeback list
+    - fuse: use unsigned type for getxattr/listxattr size truncation
+    - clk: qcom: clk-alpha-pll: Fix the pll post div mask
+    - clk: qcom: clk-alpha-pll: Fix the trion pll postdiv set rate API
+    - can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open
+    - tracing: Avoid possible softlockup in tracing_iter_reset()
+    - ila: call nf_unregister_net_hooks() sooner
+    - sched: sch_cake: fix bulk flow accounting logic for host fairness
+    - nilfs2: fix missing cleanup on rollforward recovery error
+    - nilfs2: fix state management in error path of log writing function
+    - mptcp: pm: re-using ID of unused flushed subflows
+    - mptcp: pm: only decrement add_addr_accepted for MPJ req
+    - mptcp: pm: check add_addr_accept_max before accepting new ADD_ADDR
+    - mptcp: pm: fullmesh: select the right ID later
+    - mptcp: constify a bunch of of helpers
+    - mptcp: pm: avoid possible UaF when selecting endp
+    - mptcp: avoid duplicated SUB_CLOSED events
+    - mptcp: close subflow when receiving TCP+FIN
+    - mptcp: pm: ADD_ADDR 0 is not a new address
+    - mptcp: pm: do not remove already closed subflows
+    - mptcp: pm: skip connecting to already established sf
+    - mptcp: pr_debug: add missing \n at the end
+    - mptcp: pm: send ACK on an active subflow
+    - ALSA: hda: Add input value sanity checks to HDMI channel map controls
+    - smack: unix sockets: fix accept()ed socket label
+    - irqchip/armada-370-xp: Do not allow mapping IRQ 0 and 1
+    - af_unix: Remove put_pid()/put_cred() in copy_peercred().
+    - iommu: sun50i: clear bypass register
+    - netfilter: nf_conncount: fix wrong variable type
+    - udf: Avoid excessive partition lengths
+    - media: vivid: fix wrong sizeimage value for mplane
+    - leds: spi-byte: Call of_node_put() on error path
+    - wifi: brcmsmac: advertise MFP_CAPABLE to enable WPA3
+    - usb: uas: set host status byte on data completion error
+    - drm/amd/display: Check HDCP returned status
+    - media: vivid: don't set HDMI TX controls if there are no HDMI outputs
+    - PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
+    - media: qcom: camss: Add check for v4l2_fwnode_endpoint_parse
+    - pcmcia: Use resource_size function on resource object
+    - drm/amdgpu: check for LINEAR_ALIGNED correctly in check_tiling_flags_gfx6
+    - can: bcm: Remove proc entry when dev is unregistered.
+    - can: m_can: Release irq on error in m_can_open
+    - igb: Fix not clearing TimeSync interrupts for 82580
+    - platform/x86: dell-smbios: Fix error path in dell_smbios_init()
+    - tcp_bpf: fix return value of tcp_bpf_sendmsg()
+    - igc: Unlock on error in igc_io_resume()
+    - ice: check ICE_VSI_DOWN under rtnl_lock when preparing for reset
+    - net: usb: don't write directly to netdev->dev_addr
+    - usbnet: modern method to get random MAC
+    - bareudp: Fix device stats updates.
+    - gro: remove rcu_read_lock/rcu_read_unlock from gro_receive handlers
+    - gro: remove rcu_read_lock/rcu_read_unlock from gro_complete handlers
+    - fou: Fix null-ptr-deref in GRO.
+    - net: bridge: br_fdb_external_learn_add(): always set EXT_LEARN
+    - net: dsa: vsc73xx: fix possible subblocks range of CAPT block
+    - ASoC: topology: Properly initialize soc_enum values
+    - dm init: Handle minors larger than 255
+    - iommu/vt-d: Handle volatile descriptor status read
+    - cgroup: Protect css->cgroup write under css_set_lock
+    - um: line: always fill *error_out in setup_one_line()
+    - devres: Initialize an uninitialized struct member
+    - pci/hotplug/pnv_php: Fix hotplug driver crash on Powernv
+    - hwmon: (adc128d818) Fix underflows seen when writing limit attributes
+    - hwmon: (lm95234) Fix underflows seen when writing limit attributes
+    - hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
+    - hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
+    - libbpf: Add NULL checks to bpf_object__{prev_map,next_map}
+    - drm/amdgpu: Set no_hw_access when VF request full GPU fails
+    - ext4: fix possible tid_t sequence overflows
+    - dma-mapping: benchmark: Don't starve others when doing the test
+    - wifi: mwifiex: Do not return unused priv in mwifiex_get_priv_by_id()
+    - smp: Add missing destroy_work_on_stack() call in smp_call_on_cpu()
+    - fs/ntfs3: Check more cases when directory is corrupted
+    - btrfs: replace BUG_ON with ASSERT in walk_down_proc()
+    - btrfs: clean up our handling of refs == 0 in snapshot delete
+    - btrfs: replace BUG_ON() with error handling at update_ref_for_cow()
+    - riscv: set trap vector earlier
+    - PCI: Add missing bridge lock to pci_bus_lock()
+    - net: dpaa: avoid on-stack arrays of NR_CPUS elements
+    - i3c: mipi-i3c-hci: Error out instead on BUG_ON() in IBI DMA setup
+    - kselftests: dmabuf-heaps: Ensure the driver name is null-terminated
+    - btrfs: initialize location to fix -Wmaybe-uninitialized in
+      btrfs_lookup_dentry()
+    - s390/vmlinux.lds.S: Move ro_after_init section behind rodata section
+    - HID: cougar: fix slab-out-of-bounds Read in cougar_report_fixup
+    - HID: amd_sfh: free driver_data after destroying hid device
+    - Input: uinput - reject requests with unreasonable number of slots
+    - usbnet: ipheth: race between ipheth_close and error handling
+    - Squashfs: sanity check symbolic link size
+    - of/irq: Prevent device address out-of-bounds read in interrupt map walk
+    - lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc()
+    - MIPS: cevt-r4k: Don't call get_c0_compare_int if timer irq is installed
+    - ata: pata_macio: Use WARN instead of BUG
+    - NFSv4: Add missing rescheduling points in
+      nfs_client_return_marked_delegations
+    - cifs: Check the lease context if we actually got a lease
+    - staging: iio: frequency: ad9834: Validate frequency parameter value
+    - iio: buffer-dmaengine: fix releasing dma channel on error
+    - iio: fix scale application in iio_convert_raw_to_processed_unlocked
+    - iio: adc: ad7124: fix config comparison
+    - iio: adc: ad7124: fix chip ID mismatch
+    - usb: dwc3: core: update LC timer as per USB Spec V3.2
+    - binder: fix UAF caused by offsets overwrite
+    - nvmem: Fix return type of devm_nvmem_device_get() in kerneldoc
+    - uio_hv_generic: Fix kernel NULL pointer dereference in hv_uio_rescind
+    - Drivers: hv: vmbus: Fix rescind handling in uio_hv_generic
+    - VMCI: Fix use-after-free when removing resource in vmci_resource_remove()
+    - clocksource/drivers/imx-tpm: Fix return -ETIME when delta exceeds INT_MAX
+    - clocksource/drivers/imx-tpm: Fix next event not taking effect sometime
+    - clocksource/drivers/timer-of: Remove percpu irq related code
+    - uprobes: Use kzalloc to allocate xol area
+    - perf/aux: Fix AUX buffer serialization
+    - ksmbd: unset the binding mark of a reused connection
+    - ksmbd: Unlock on in ksmbd_tcp_set_interfaces()
+    - nilfs2: replace snprintf in show functions with sysfs_emit
+    - nilfs2: protect references to superblock parameters exposed in sysfs
+    - workqueue: wq_watchdog_touch is always called with valid CPU
+    - workqueue: Improve scalability of workqueue watchdog touch
+    - ACPI: processor: Return an error if acpi_processor_get_info() fails in
+      processor_add()
+    - ACPI: processor: Fix memory leaks in error paths of processor_add()
+    - arm64: acpi: Move get_cpu_for_acpi_id() to a header
+    - arm64: acpi: Harden get_cpu_for_acpi_id() against missing CPU entry
+    - nvmet-tcp: fix kernel crash if commands allocation fails
+    - ASoC: sunxi: sun4i-i2s: fix LRCLK polarity in i2s mode
+    - drm/i915/fence: Mark debug_fence_init_onstack() with __maybe_unused
+    - drm/i915/fence: Mark debug_fence_free() with __maybe_unused
+    - gpio: rockchip: fix OF node leak in probe()
+    - net: more strict VIRTIO_NET_HDR_GSO_UDP_L4 validation
+    - net: change maximum number of UDP segments to 128
+    - gso: fix dodgy bit handling for GSO_UDP_L4
+    - net: drop bad gso csum_start and offset in virtio_net_hdr
+    - x86/mm: Fix PTI for i386 some more
+    - net, sunrpc: Remap EPERM in case of connection failure in
+      xs_tcp_setup_socket
+    - btrfs: fix race between direct IO write and fsync when using same fd
+    - memcg: protect concurrent access to mem_cgroup_idr
+    - udp: fix receiving fraglist GSO packets
+    - Linux 5.15.167
+  * CVE-2024-41071
+    - wifi: mac80211: Avoid address calculations via out of bounds array indexing
+  * CVE-2024-40915
+    - riscv: rewrite __kernel_map_pages() to fix sleeping in invalid context
+  * CVE-2024-38611
+    - media: i2c: et8ek8: Don't strip remove function when driver is builtin
+  * CVE-2024-38602
+    - ax25: Fix reference count leak issues of ax25_dev
+  * CVE-2024-26669
+    - net/sched: flower: Fix chain template offload
+  * CVE-2024-26607
+    - drm/bridge: sii902x: Fix probing race issue
+  * Jammy update: v5.15.166 upstream stable release (LP: #2080594)
+    - fuse: Initialize beyond-EOF page contents before setting uptodate
+    - char: xillybus: Don't destroy workqueue from work item running on it
+    - char: xillybus: Refine workqueue handling
+    - char: xillybus: Check USB endpoints when probing device
+    - ALSA: usb-audio: Add delay quirk for VIVO USB-C-XE710 HEADSET
+    - ALSA: usb-audio: Support Yamaha P-125 quirk entry
+    - xhci: Fix Panther point NULL pointer deref at full-speed re-enumeration
+    - thunderbolt: Mark XDomain as unplugged when router is removed
+    - s390/dasd: fix error recovery leading to data corruption on ESE devices
+    - arm64: ACPI: NUMA: initialize all values of acpi_early_node_map to
+      NUMA_NO_NODE
+    - dm resume: don't return EINVAL when signalled
+    - dm persistent data: fix memory allocation failure
+    - vfs: Don't evict inode under the inode lru traversing context
+    - fs/ntfs3: add prefix to bitmap_size() and use BITS_TO_U64()
+    - s390/cio: rename bitmap_size() -> idset_bitmap_size()
+    - btrfs: rename bitmap_set_bits() -> btrfs_bitmap_set_bits()
+    - bitmap: introduce generic optimized bitmap_size()
+    - fix bitmap corruption on close_range() with CLOSE_RANGE_UNSHARE
+    - selinux: fix potential counting error in avc_add_xperms_decision()
+    - btrfs: tree-checker: add dev extent item checks
+    - drm/amdgpu: Actually check flags for all context ops.
+    - memcg_write_event_control(): fix a user-triggerable oops
+    - drm/amdgpu/jpeg2: properly set atomics vmid field
+    - s390/uv: Panic for set and remove shared access UVC errors
+    - igc: Correct the launchtime offset
+    - igc: remove I226 Qbv BaseTime restriction
+    - igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer
+    - net/mlx5e: Correctly report errors for ethtool rx flows
+    - atm: idt77252: prevent use after free in dequeue_rx()
+    - net: axienet: Fix register defines comment description
+    - net: dsa: vsc73xx: pass value in phy_write operation
+    - net: dsa: vsc73xx: use read_poll_timeout instead delay loop
+    - net: dsa: vsc73xx: check busy flag in MDIO operations
+    - mlxbf_gige: Remove two unused function declarations
+    - mlxbf_gige: disable RX filters until RX path initialized
+    - mptcp: correct MPTCP_SUBFLOW_ATTR_SSN_OFFSET reserved size
+    - netfilter: allow ipv6 fragments to arrive on different devices
+    - netfilter: flowtable: initialise extack before use
+    - netfilter: nf_queue: drop packets with cloned unconfirmed conntracks
+    - net: hns3: fix wrong use of semaphore up
+    - net: hns3: fix a deadlock problem when config TC during resetting
+    - ALSA: hda/realtek: Fix noise from speakers on Lenovo IdeaPad 3 15IAU7
+    - ssb: Fix division by zero issue in ssb_calc_clock_rate
+    - wifi: cfg80211: check wiphy mutex is held for wdev mutex
+    - wifi: mac80211: fix BA session teardown race
+    - wifi: cw1200: Avoid processing an invalid TIM IE
+    - i2c: riic: avoid potential division by zero
+    - RDMA/rtrs: Fix the problem of variable not initialized fully
+    - s390/smp,mcck: fix early IPI handling
+    - i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
+    - i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
+    - media: radio-isa: use dev_name to fill in bus_info
+    - staging: iio: resolver: ad2s1210: fix use before initialization
+    - drm/amd/display: Validate hw_points_num before using it
+    - staging: ks7010: disable bh on tx_dev_lock
+    - binfmt_misc: cleanup on filesystem umount
+    - media: qcom: venus: fix incorrect return value
+    - scsi: spi: Fix sshdr use
+    - gfs2: setattr_chown: Add missing initialization
+    - wifi: iwlwifi: abort scan when rfkill on but device enabled
+    - wifi: iwlwifi: fw: Fix debugfs command sending
+    - IB/hfi1: Fix potential deadlock on &irq_src_lock and &dd->uctxt_lock
+    - hwmon: (ltc2992) Avoid division by zero
+    - arm64: Fix KASAN random tag seed initialization
+    - memory: tegra: Skip SID programming if SID registers aren't set
+    - powerpc/xics: Check return value of kasprintf in icp_native_map_one_cpu
+    - nvmet-trace: avoid dereferencing pointer too early
+    - ext4: do not trim the group with corrupted block bitmap
+    - afs: fix __afs_break_callback() / afs_drop_open_mmap() race
+    - fuse: fix UAF in rcu pathwalks
+    - quota: Remove BUG_ON from dqget()
+    - media: pci: cx23885: check cx23885_vdev_init() return
+    - fs: binfmt_elf_efpic: don't use missing interpreter's properties
+    - scsi: lpfc: Initialize status local variable in lpfc_sli4_repost_sgl_list()
+    - media: drivers/media/dvb-core: copy user arrays safely
+    - net/sun3_82586: Avoid reading past buffer in debug output
+    - drm/lima: set gp bus_stop bit before hard reset
+    - virtiofs: forbid newlines in tags
+    - clocksource/drivers/arm_global_timer: Guard against division by zero
+    - netlink: hold nlk->cb_mutex longer in __netlink_dump_start()
+    - md: clean up invalid BUG_ON in md_ioctl
+    - x86: Increase brk randomness entropy for 64-bit systems
+    - memory: stm32-fmc2-ebi: check regmap_read return value
+    - parisc: Use irq_enter_rcu() to fix warning at kernel/context_tracking.c:367
+    - powerpc/boot: Handle allocation failure in simple_realloc()
+    - powerpc/boot: Only free if realloc() succeeds
+    - btrfs: change BUG_ON to assertion when checking for delayed_node root
+    - btrfs: handle invalid root reference found in may_destroy_subvol()
+    - btrfs: send: handle unexpected data in header buffer in begin_cmd()
+    - btrfs: change BUG_ON to assertion in tree_move_down()
+    - btrfs: delete pointless BUG_ON check on quota root in
+      btrfs_qgroup_account_extent()
+    - f2fs: fix to do sanity check in update_sit_entry
+    - usb: gadget: fsl: Increase size of name buffer for endpoints
+    - Bluetooth: bnep: Fix out-of-bound access
+    - net: hns3: add checking for vf id of mailbox
+    - nvmet-tcp: do not continue for invalid icreq
+    - NFS: avoid infinite loop in pnfs_update_layout.
+    - openrisc: Call setup_memory() earlier in the init sequence
+    - s390/iucv: fix receive buffer virtual vs physical address confusion
+    - clocksource: Make watchdog and suspend-timing multiplication overflow safe
+    - platform/x86: lg-laptop: fix %s null argument warning
+    - usb: dwc3: core: Skip setting event buffers for host only controllers
+    - irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
+    - ext4: set the type of max_zeroout to unsigned int to avoid overflow
+    - nvmet-rdma: fix possible bad dereference when freeing rsps
+    - hrtimer: Prevent queuing of hrtimer without a function callback
+    - gtp: pull network headers in gtp_dev_xmit()
+    - block: use "unsigned long" for blk_validate_block_size().
+    - nfsd: move reply cache initialization into nfsd startup
+    - nfsd: move init of percpu reply_cache_stats counters back to nfsd_init_net
+    - NFSD: Refactor nfsd_reply_cache_free_locked()
+    - NFSD: Rename nfsd_reply_cache_alloc()
+    - NFSD: Replace nfsd_prune_bucket()
+    - NFSD: Refactor the duplicate reply cache shrinker
+    - NFSD: Rewrite synopsis of nfsd_percpu_counters_init()
+    - NFSD: Fix frame size warning in svc_export_parse()
+    - sunrpc: don't change ->sv_stats if it doesn't exist
+    - nfsd: stop setting ->pg_stats for unused stats
+    - sunrpc: pass in the sv_stats struct through svc_create_pooled
+    - sunrpc: remove ->pg_stats from svc_program
+    - sunrpc: use the struct net as the svc proc private
+    - nfsd: rename NFSD_NET_* to NFSD_STATS_*
+    - nfsd: expose /proc/net/sunrpc/nfsd in net namespaces
+    - nfsd: make all of the nfsd stats per-network namespace
+    - nfsd: remove nfsd_stats, make th_cnt a global counter
+    - nfsd: make svc_stat per-network namespace instead of global
+    - media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)
+    - dm suspend: return -ERESTARTSYS instead of -EINTR
+    - net: mana: Fix doorbell out of order violation and avoid unnecessary
+      doorbell rings
+    - platform/surface: aggregator: Fix warning when controller is destroyed in
+      probe
+    - Bluetooth: hci_core: Fix LE quote calculation
+    - Bluetooth: SMP: Fix assumption of Central always being Initiator
+    - tc-testing: don't access non-existent variable on exception
+    - kcm: Serialise kcm_sendmsg() for the same socket.
+    - netfilter: nft_counter: Disable BH in nft_counter_offload_stats().
+    - netfilter: nft_counter: Synchronize nft_counter_reset() against reader.
+    - ip6_tunnel: Fix broken GRO
+    - bonding: fix bond_ipsec_offload_ok return type
+    - bonding: fix null pointer deref in bond_ipsec_offload_ok
+    - bonding: fix xfrm real_dev null pointer dereference
+    - bonding: fix xfrm state handling when clearing active slave
+    - ice: fix ICE_LAST_OFFSET formula
+    - dpaa2-switch: Fix error checking in dpaa2_switch_seed_bp()
+    - net: dsa: mv88e6xxx: read FID when handling ATU violations
+    - net: dsa: mv88e6xxx: replace ATU violation prints with trace points
+    - net: dsa: mv88e6xxx: Fix out-of-bound access
+    - ipv6: prevent UAF in ip6_send_skb()
+    - ipv6: fix possible UAF in ip6_finish_output2()
+    - ipv6: prevent possible UAF in ip6_xmit()
+    - netfilter: flowtable: validate vlan header
+    - net: xilinx: axienet: Always disable promiscuous mode
+    - net: xilinx: axienet: Fix dangling multicast addresses
+    - drm/msm/dpu: don't play tricks with debug macros
+    - drm/msm/dp: reset the link phy params before link training
+    - drm/msm/dpu: cleanup FB if dpu_format_populate_layout fails
+    - mmc: mmc_test: Fix NULL dereference on allocation failure
+    - Bluetooth: MGMT: Add error handling to pair_device()
+    - scsi: core: Fix the return value of scsi_logical_block_count()
+    - MIPS: Loongson64: Set timer mode in cpu-probe
+    - HID: wacom: Defer calculation of resolution until resolution_code is known
+    - HID: microsoft: Add rumble support to latest xbox controllers
+    - cxgb4: add forgotten u64 ivlan cast before shift
+    - KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3
+    - mmc: dw_mmc: allow biu and ciu clocks to defer
+    - Revert "drm/amd/display: Validate hw_points_num before using it"
+    - hwmon: (ltc2992) Fix memory leak in ltc2992_parse_dt()
+    - ALSA: timer: Relax start tick time check for slave timer elements
+    - mm/numa: no task_numa_fault() call if PMD is changed
+    - mm/numa: no task_numa_fault() call if PTE is changed
+    - Input: MT - limit max slots
+    - tools: move alignment-related macros to new <linux/align.h>
+    - btrfs: run delayed iputs when flushing delalloc
+    - pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins
+    - pinctrl: single: fix potential NULL dereference in pcs_get_function()
+    - wifi: mwifiex: duplicate static structs used in driver instances
+    - net: mana: Fix race of mana_hwc_post_rx_wqe and new hwc response
+    - mptcp: sched: check both backup in retrans
+    - Revert "MIPS: Loongson64: reset: Prioritise firmware service"
+    - drm/amdkfd: don't allow mapping the MMIO HDP page with large pages
+    - ata: libata-core: Fix null pointer dereference on error
+    - cgroup/cpuset: Prevent UAF in proc_cpuset_show()
+    - net:rds: Fix possible deadlock in rds_message_put
+    - soundwire: stream: fix programming slave ports for non-continous port maps
+    - PM: core: Remove DEFINE_UNIVERSAL_DEV_PM_OPS() macro
+    - PM: core: Add EXPORT[_GPL]_SIMPLE_DEV_PM_OPS macros
+    - PM: runtime: Add DEFINE_RUNTIME_DEV_PM_OPS() macro
+    - phy: xilinx: add runtime PM support
+    - phy: xilinx: phy-zynqmp: dynamic clock support for power-save
+    - phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
+    - dmaengine: dw: Add peripheral bus width verification
+    - dmaengine: dw: Add memory bus width verification
+    - ethtool: check device is present when getting link settings
+    - gtp: fix a potential NULL pointer dereference
+    - net: busy-poll: use ktime_get_ns() instead of local_clock()
+    - nfc: pn533: Add poll mod list filling check
+    - soc: qcom: cmd-db: Map shared memory as WC, not WB
+    - cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
+    - USB: serial: option: add MeiG Smart SRM825L
+    - usb: dwc3: omap: add missing depopulate in probe error path
+    - usb: dwc3: core: Prevent USB core invalid event buffer address access
+    - usb: dwc3: st: fix probed platform device ref count on probe error path
+    - usb: dwc3: st: add missing depopulate in probe error path
+    - usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in
+      remove_power_attributes()
+    - usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
+    - usb: cdnsp: fix for Link TRB with TC
+    - phy: zynqmp: Enable reference clock correctly
+    - igc: Fix reset adapter logics when tx mode change
+    - igc: Fix qbv tx latency by setting gtxoffset
+    - scsi: aacraid: Fix double-free on probe failure
+    - apparmor: fix policy_unpack_test on big endian systems
+    - Linux 5.15.166
+  * CVE-2024-26893
+    - firmware: arm_scmi: Fix double free in SMC transport cleanup path
+  * [22.10 FEAT] KVM: Secure Execution guest dump encryption with customer keys
+    - kernel part (LP: #1959940)
+    - s390: uv: Add offset comments to UV query struct and fix naming
+    - s390/uv: Add SE hdr query information
+    - s390/uv: Add dump fields to query
+    - KVM: s390: pv: Add query interface
+    - KVM: s390: pv: Add dump support definitions
+    - KVM: s390: pv: Add query dump information
+    - KVM: s390: Add configuration dump functionality
+    - KVM: s390: Add CPU dump functionality
+    - KVM: s390: Add KVM_CAP_S390_PROTECTED_DUMP
+    - Documentation: KVM: add separate directories for architecture-specific
+      documentation
+    - Documentation: virt: Protected virtual machine dumps
+    - Documentation/virt/kvm/api.rst: Add protvirt dump/info api descriptions
+    - Documentation/virt/kvm/api.rst: Explain rc/rrc delivery
+  * turbostat fails with too many open files on large systems (LP: #2069961)
+    - tools/power turbostat: Increase the limit for fd opened
+  * Jammy update: v5.15.165 upstream stable release (LP: #2078428)
+    - f2fs: fix return value of f2fs_convert_inline_inode()
+    - f2fs: fix to don't dirty inode for readonly filesystem
+    - EDAC, i10nm: make skx_common.o a separate module
+    - platform/chrome: cros_ec_debugfs: fix wrong EC message version
+    - block: refactor to use helper
+    - block: cleanup bio_integrity_prep
+    - block: initialize integrity buffer to zero before writing it to media
+    - hfsplus: fix to avoid false alarm of circular locking
+    - x86/of: Return consistent error type from x86_of_pci_irq_enable()
+    - x86/pci/intel_mid_pci: Fix PCIBIOS_* return code handling
+    - x86/pci/xen: Fix PCIBIOS_* return code handling
+    - x86/platform/iosf_mbi: Convert PCIBIOS_* return codes to errnos
+    - hwmon: (adt7475) Fix default duty on fan is disabled
+    - pwm: stm32: Always do lazy disabling
+    - drm/meson: fix canvas release in bind function
+    - hwmon: (max6697) Fix underflow when writing limit attributes
+    - hwmon: (max6697) Fix swapped temp{1,8} critical alarms
+    - arm64: dts: qcom: sdm845: add power-domain to UFS PHY
+    - arm64: dts: qcom: sm8250: switch UFS QMP PHY to new style of bindings
+    - arm64: dts: qcom: sm8250: add power-domain to UFS PHY
+    - soc: qcom: rpmh-rsc: Ensure irqs aren't disabled by rpmh_rsc_send_data()
+      callers
+    - arm64: dts: qcom: msm8996: specify UFS core_clk frequencies
+    - memory: fsl_ifc: Make FSL_IFC config visible and selectable
+    - soc: qcom: pdr: protect locator_addr with the main mutex
+    - soc: qcom: pdr: fix parsing of domains lists
+    - arm64: dts: rockchip: Increase VOP clk rate on RK3328
+    - ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node
+    - ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
+    - ARM: dts: imx6qdl-kontron-samx6i: fix board reset
+    - ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
+    - ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
+    - arm64: dts: mediatek: mt8183-kukui: Drop bogus output-enable property
+    - arm64: dts: mediatek: mt7622: fix "emmc" pinctrl mux
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add ports node for anx7625
+    - arm64: dts: amlogic: gx: correct hdmi clocks
+    - m68k: atari: Fix TT bootup freeze / unexpected (SCU) interrupt messages
+    - x86/xen: Convert comma to semicolon
+    - m68k: cmpxchg: Fix return value for default case in __arch_xchg()
+    - ARM: pxa: spitz: use gpio descriptors for audio
+    - ARM: spitz: fix GPIO assignment for backlight
+    - vmlinux.lds.h: catch .bss..L* sections into BSS")
+    - firmware: turris-mox-rwtm: Do not complete if there are no waiters
+    - firmware: turris-mox-rwtm: Fix checking return value of
+      wait_for_completion_timeout()
+    - firmware: turris-mox-rwtm: Initialize completion before mailbox
+    - wifi: brcmsmac: LCN PHY code is used for BCM4313 2G-only device
+    - selftests/bpf: Fix prog numbers in test_sockmap
+    - net: esp: cleanup esp_output_tail_tcp() in case of unsupported ESPINTCP
+    - tcp: annotate lockless accesses to sk->sk_err_soft
+    - tcp: annotate lockless access to sk->sk_err
+    - tcp: add tcp_done_with_error() helper
+    - tcp: fix race in tcp_write_err()
+    - tcp: fix races in tcp_v[46]_err()
+    - net/smc: set rmb's SG_MAX_SINGLE_ALLOC limitation only when
+      CONFIG_ARCH_NO_SG_CHAIN is defined
+    - selftests/bpf: Check length of recv in test_sockmap
+    - lib: objagg: Fix general protection fault
+    - mlxsw: spectrum_acl_erp: Fix object nesting warning
+    - mlxsw: spectrum_acl_bloom_filter: Make mlxsw_sp_acl_bf_key_encode() more
+      flexible
+    - mlxsw: spectrum_acl: Fix ACL scale regression and firmware errors
+    - wifi: ath11k: fix wrong handling of CCMP256 and GCMP ciphers
+    - wifi: cfg80211: fix typo in cfg80211_calculate_bitrate_he()
+    - wifi: cfg80211: handle 2x996 RU allocation in
+      cfg80211_calculate_bitrate_he()
+    - net: fec: Refactor: #define magic constants
+    - net: fec: Fix FEC_ECR_EN1588 being cleared on link-down
+    - libbpf: Checking the btf_type kind when fixing variable offsets
+    - ipvs: Avoid unnecessary calls to skb_is_gso_sctp
+    - netfilter: nf_tables: rise cap on SELinux secmark context
+    - perf/x86/intel/pt: Fix pt_topa_entry_for_page() address calculation
+    - perf: Fix perf_aux_size() for greater-than 32-bit size
+    - perf: Prevent passing zero nr_pages to rb_alloc_aux()
+    - perf: Fix default aux_watermark calculation
+    - wifi: virt_wifi: avoid reporting connection success with wrong SSID
+    - gss_krb5: Fix the error handling path for crypto_sync_skcipher_setkey
+    - wifi: virt_wifi: don't use strlen() in const context
+    - locking/rwsem: Add __always_inline annotation to __down_write_common() and
+      inlined callers
+    - selftests/bpf: Close fd in error path in drop_on_reuseport
+    - bpf: annotate BTF show functions with __printf
+    - bna: adjust 'name' buf size of bna_tcb and bna_ccb structures
+    - bpf: Eliminate remaining "make W=1" warnings in kernel/bpf/btf.o
+    - selftests: forwarding: devlink_lib: Wait for udev events after reloading
+    - xdp: fix invalid wait context of page_pool_destroy()
+    - drm/amd/pm: Fix aldebaran pcie speed reporting
+    - drm/amdgpu: Check if NBIO funcs are NULL in amdgpu_device_baco_exit
+    - drm/panel: boe-tv101wum-nl6: If prepare fails, disable GPIO before
+      regulators
+    - drm/panel: boe-tv101wum-nl6: Check for errors on the NOP in prepare()
+    - media: dvb-usb: Fix unexpected infinite loop in
+      dvb_usb_read_remote_control()
+    - media: imon: Fix race getting ictx->lock
+    - media: i2c: Fix imx412 exposure control
+    - saa7134: Unchecked i2c_transfer function result fixed
+    - media: uvcvideo: Override default flags
+    - media: renesas: vsp1: Fix _irqsave and _irq mix
+    - media: renesas: vsp1: Store RPF partition configuration per RPF instance
+    - drm/mediatek: Add missing plane settings when async update
+    - drm/mediatek: Add DRM_MODE_ROTATE_0 to rotation property
+    - leds: trigger: Unregister sysfs attributes before calling deactivate()
+    - perf report: Fix condition in sort__sym_cmp()
+    - drm/etnaviv: fix DMA direction handling for cached RW buffers
+    - drm/qxl: Add check for drm_cvt_mode
+    - Revert "leds: led-core: Fix refcount leak in of_led_get()"
+    - ext4: fix infinite loop when replaying fast_commit
+    - media: venus: flush all buffers in output plane streamoff
+    - perf intel-pt: Fix aux_watermark calculation for 64-bit size
+    - perf intel-pt: Fix exclude_guest setting
+    - mfd: rsmu: Split core code into separate module
+    - mfd: omap-usb-tll: Use struct_size to allocate tll
+    - xprtrdma: Fix rpcrdma_reqs_reset()
+    - SUNRPC: avoid soft lockup when transmitting UDP to reachable server.
+    - NFSv4.1 another fix for EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - ext4: return early for non-eligible fast_commit track events
+    - ext4: don't track ranges in fast_commit if inode has inlined data
+    - ext4: avoid writing unitialized memory to disk in EA inodes
+    - sparc64: Fix incorrect function signature and add prototype for
+      prom_cif_init
+    - SUNRPC: Fixup gss_status tracepoint error output
+    - PCI: Fix resource double counting on remove & rescan
+    - clk: qcom: branch: Add helper functions for setting retain bits
+    - clk: qcom: gcc-sc7280: Update force mem core bit for UFS ICE clock
+    - coresight: Fix ref leak when of_coresight_parse_endpoint() fails
+    - RDMA/mlx5: Set mkeys for dmabuf at PAGE_SIZE
+    - RDMA/cache: Release GID table even if leak is detected
+    - Input: qt1050 - handle CHIP_ID reading error
+    - RDMA/mlx4: Fix truncated output warning in mad.c
+    - RDMA/mlx4: Fix truncated output warning in alias_GUID.c
+    - RDMA/rxe: Don't set BTH_ACK_MASK for UC or UD QPs
+    - ASoC: max98088: Check for clk_prepare_enable() error
+    - mtd: make mtd_test.c a separate module
+    - RDMA/device: Return error earlier if port in not valid
+    - Input: elan_i2c - do not leave interrupt disabled on suspend failure
+    - PCI: endpoint: Clean up error handling in vpci_scan_bus()
+    - vhost/vsock: always initialize seqpacket_allow
+    - net: missing check virtio
+    - MIPS: Octeron: remove source file executable bit
+    - powerpc/xmon: Fix disassembly CPU feature checks
+    - macintosh/therm_windtunnel: fix module unload.
+    - RDMA/hns: Fix missing pagesize and alignment check in FRMR
+    - RDMA/hns: Fix undifined behavior caused by invalid max_sge
+    - RDMA/hns: Fix insufficient extend DB for VFs.
+    - bnxt_re: Fix imm_data endianness
+    - netfilter: ctnetlink: use helper function to calculate expect ID
+    - netfilter: nf_set_pipapo: fix initial map fill
+    - net: dsa: mv88e6xxx: Limit chip-wide frame size config to CPU ports
+    - net: dsa: b53: Limit chip-wide jumbo frame config to CPU ports
+    - fs/ntfs3: Use ALIGN kernel macro
+    - fs/ntfs3: Merge synonym COMPRESSION_UNIT and NTFS_LZNT_CUNIT
+    - fs/ntfs3: Fix transform resident to nonresident for compressed files
+    - fs/ntfs3: Missed NI_FLAG_UPDATE_PARENT setting
+    - fs/ntfs3: Fix getting file type
+    - pinctrl: rockchip: update rk3308 iomux routes
+    - pinctrl: core: fix possible memory leak when pinctrl_enable() fails
+    - pinctrl: single: fix possible memory leak when pinctrl_enable() fails
+    - pinctrl: ti: ti-iodelay: Drop if block with always false condition
+    - pinctrl: ti: ti-iodelay: fix possible memory leak when pinctrl_enable()
+      fails
+    - pinctrl: freescale: mxs: Fix refcount of child
+    - fs/ntfs3: Replace inode_trylock with inode_lock
+    - fs/ntfs3: Fix field-spanning write in INDEX_HDR
+    - fs/proc/task_mmu: indicate PM_FILE for PMD-mapped file THP
+    - nilfs2: avoid undefined behavior in nilfs_cnt32_ge macro
+    - rtc: interface: Add RTC offset to alarm after fix-up
+    - fs/ntfs3: Missed error return
+    - landlock: Don't lose track of restrictions on cred_transfer
+    - mm/hugetlb: fix possible recursive locking detected warning
+    - mm: mmap_lock: replace get_memcg_path_buf() with on-stack buffer
+    - dt-bindings: thermal: correct thermal zone node name limit
+    - tick/broadcast: Make takeover of broadcast hrtimer reliable
+    - net: netconsole: Disable target before netpoll cleanup
+    - af_packet: Handle outgoing VLAN packets without hardware offloading
+    - ipv6: take care of scope when choosing the src addr
+    - sched/fair: set_load_weight() must also call reweight_task() for SCHED_IDLE
+      tasks
+    - fuse: verify {g,u}id mount options correctly
+    - char: tpm: Fix possible memory leak in tpm_bios_measurements_open()
+    - media: venus: fix use after free in vdec_close
+    - ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error
+    - hfs: fix to initialize fields of hfs_inode_info after hfs_alloc_inode()
+    - ext2: Verify bitmap and itable block numbers before using them
+    - drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes
+    - drm/gma500: fix null pointer dereference in psb_intel_lvds_get_modes
+    - scsi: qla2xxx: Fix optrom version displayed in FDMI
+    - drm/amd/display: Check for NULL pointer
+    - sched/fair: Use all little CPUs for CPU-bound workloads
+    - apparmor: use kvfree_sensitive to free data->data
+    - task_work: s/task_work_cancel()/task_work_cancel_func()/
+    - task_work: Introduce task_work_cancel() again
+    - udf: Avoid using corrupted block bitmap buffer
+    - m68k: amiga: Turn off Warp1260 interrupts during boot
+    - ext4: check dot and dotdot of dx_root before making dir indexed
+    - ext4: make sure the first directory block is not a hole
+    - io_uring: tighten task exit cancellations
+    - selftests/landlock: Add cred_transfer test
+    - wifi: mwifiex: Fix interface type change
+    - leds: ss4200: Convert PCIBIOS_* return codes to errnos
+    - jbd2: make jbd2_journal_get_max_txn_bufs() internal
+    - media: uvcvideo: Fix integer overflow calculating timestamp
+    - KVM: VMX: Split out the non-virtualization part of vmx_interrupt_blocked()
+    - ALSA: usb-audio: Fix microphone sound on HD webcam.
+    - ALSA: usb-audio: Move HD Webcam quirk to the right place
+    - ALSA: usb-audio: Add a quirk for Sonix HD USB Camera
+    - tools/memory-model: Fix bug in lock.cat
+    - hwrng: amd - Convert PCIBIOS_* return codes to errnos
+    - PCI: hv: Return zero, not garbage, when reading PCI_INTERRUPT_PIN
+    - PCI: dw-rockchip: Fix initial PERST# GPIO value
+    - PCI: rockchip: Use GPIOD_OUT_LOW flag while requesting ep_gpio
+    - binder: fix hang of unregistered readers
+    - dev/parport: fix the array out-of-bounds risk
+    - fs/ntfs3: Update log->page_{mask,bits} if log->page_size changed
+    - scsi: qla2xxx: Return ENOBUFS if sg_cnt is more than one for ELS cmds
+    - clk: davinci: da8xx-cfgchip: Initialize clk_init_data before use
+    - ubi: eba: properly rollback inside self_check_eba
+    - decompress_bunzip2: fix rare decompression failure
+    - kbuild: Fix '-S -c' in x86 stack protector scripts
+    - kobject_uevent: Fix OOB access within zap_modalias_env()
+    - gve: Fix an edge case for TSO skb validity check
+    - devres: Fix devm_krealloc() wasting memory
+    - devres: Fix memory leakage caused by driver API devm_free_percpu()
+    - mm/numa_balancing: teach mpol_to_str about the balancing mode
+    - rtc: cmos: Fix return value of nvmem callbacks
+    - scsi: qla2xxx: During vport delete send async logout explicitly
+    - scsi: qla2xxx: Unable to act on RSCN for port online
+    - scsi: qla2xxx: Fix for possible memory corruption
+    - scsi: qla2xxx: Use QP lock to search for bsg
+    - scsi: qla2xxx: Fix flash read failure
+    - scsi: qla2xxx: Complete command early within lock
+    - scsi: qla2xxx: validate nvme_local_port correctly
+    - perf: Fix event leak upon exit
+    - perf: Fix event leak upon exec and file release
+    - perf/x86/intel/uncore: Fix the bits of the CHA extended umask for SPR
+    - perf/x86/intel/pt: Fix topa_entry base length
+    - perf/x86/intel/pt: Fix a topa_entry base address calculation
+    - drm/i915/gt: Do not consider preemption during execlists_dequeue for gen8
+    - drm/amdgpu/sdma5.2: Update wptr registers as well as doorbell
+    - drm/i915/dp: Reset intel_dp->link_trained before retraining the link
+    - rtc: isl1208: Fix return value of nvmem callbacks
+    - watchdog/perf: properly initialize the turbo mode timestamp and rearm
+      counter
+    - platform: mips: cpu_hwmon: Disable driver on unsupported hardware
+    - RDMA/iwcm: Fix a use-after-free related to destroying CM IDs
+    - selftests/sigaltstack: Fix ppc64 GCC build
+    - rbd: don't assume rbd_is_lock_owner() for exclusive mappings
+    - remoteproc: stm32_rproc: Fix mailbox interrupts queuing
+    - remoteproc: imx_rproc: Skip over memory region when node value is NULL
+    - MIPS: ip30: ip30-console: Add missing include
+    - MIPS: dts: loongson: Fix GMAC phy node
+    - MIPS: Loongson64: env: Hook up Loongsson-2K
+    - MIPS: Loongson64: Remove memory node for builtin-dtb
+    - MIPS: Loongson64: reset: Prioritise firmware service
+    - MIPS: Loongson64: Test register availability before use
+    - drm/panfrost: Mark simple_ondemand governor as softdep
+    - rbd: rename RBD_LOCK_STATE_RELEASING and releasing_wait
+    - rbd: don't assume RBD_LOCK_STATE_LOCKED for exclusive mappings
+    - Bluetooth: btusb: Add RTL8852BE device 0489:e125 to device tables
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x13d3:0x3591
+    - nilfs2: handle inconsistent state in nilfs_btnode_create_block()
+    - io_uring/io-wq: limit retrying worker initialisation
+    - kernel: rerun task_work while freezing in get_signal()
+    - kdb: address -Wformat-security warnings
+    - kdb: Use the passed prompt in kdb_position_cursor()
+    - jfs: Fix array-index-out-of-bounds in diFree
+    - dmaengine: ti: k3-udma: Fix BCHAN count with UHC and HC channels
+    - phy: cadence-torrent: Check return value on register read
+    - um: time-travel: fix time-travel-start option
+    - um: time-travel: fix signal blocking race/hang
+    - libbpf: Fix no-args func prototype BTF dumping syntax
+    - dma: fix call order in dmam_free_coherent
+    - bpf, events: Use prog to emit ksymbol event for main program
+    - MIPS: SMP-CPS: Fix address for GCR_ACCESS register for CM3 and later
+    - ipv4: Fix incorrect source address in Record Route option
+    - net: bonding: correctly annotate RCU in bond_should_notify_peers()
+    - netfilter: nft_set_pipapo_avx2: disable softinterrupts
+    - tipc: Return non-zero value from tipc_udp_addr2str() on error
+    - net: stmmac: Correct byte order of perfect_match
+    - net: nexthop: Initialize all fields in dumped nexthops
+    - bpf: Fix a segment issue when downgrading gso_size
+    - mISDN: Fix a use after free in hfcmulti_tx()
+    - apparmor: Fix null pointer deref when receiving skb during sock creation
+    - powerpc: fix a file leak in kvm_vcpu_ioctl_enable_cap()
+    - lirc: rc_dev_get_from_fd(): fix file leak
+    - spi: spidev: Make probe to fail early if a spidev compatible is used
+    - spi: spidev: Replace ACPI specific code by device_get_match_data()
+    - spi: spidev: Replace OF specific code by device property API
+    - spidev: Add Silicon Labs EM3581 device compatible
+    - spi: spidev: order compatibles alphabetically
+    - spi: spidev: add correct compatible for Rohm BH2228FV
+    - ASoC: Intel: use soc_intel_is_byt_cr() only when IOSF_MBI is reachable
+    - ceph: fix incorrect kmalloc size of pagevec mempool
+    - iommu: sprd: Avoid NULL deref in sprd_iommu_hw_en
+    - nvme: split command copy into a helper
+    - nvme: separate command prep and issue
+    - nvme-pci: add missing condition check for existence of mapped data
+    - fs: don't allow non-init s_user_ns for filesystems without FS_USERNS_MOUNT
+    - powerpc/configs: Update defconfig with now user-visible CONFIG_FSL_IFC
+    - arm64: dts: qcom: msm8996: Move '#clock-cells' to QMP PHY child node
+    - arm64: dts: qcom: msm8998: drop USB PHY clock index
+    - arm64: dts: qcom: msm8998: switch USB QMP PHY to new style of bindings
+    - arm64: dts: qcom: msm8998: Disable SS instance in Parkmode for USB
+    - arm64: dts: qcom: ipq8074: Disable SS instance in Parkmode for USB
+    - sysctl: always initialize i_uid/i_gid
+    - ext4: make ext4_es_insert_extent() return void
+    - ext4: refactor ext4_da_map_blocks()
+    - ext4: convert to exclusive lock while inserting delalloc extents
+    - ext4: factor out a common helper to query extent map
+    - ext4: check the extent status again before inserting delalloc block
+    - soc: xilinx: move PM_INIT_FINALIZE to zynqmp_pm_domains driver
+    - drivers: soc: xilinx: check return status of get_api_version()
+    - leds: trigger: use RCU to protect the led_cdevs list
+    - leds: trigger: Remove unused function led_trigger_rename_static()
+    - leds: trigger: Store brightness set by led_trigger_event()
+    - leds: trigger: Call synchronize_rcu() before calling trig->activate()
+    - leds: triggers: Flush pending brightness before activating trigger
+    - irqdomain: Fixed unbalanced fwnode get and put
+    - genirq: Allow the PM device to originate from irq domain
+    - irqchip/imx-irqsteer: Constify irq_chip struct
+    - irqchip/imx-irqsteer: Add runtime PM support
+    - irqchip/imx-irqsteer: Handle runtime power management correctly
+    - drm/dp_mst: Fix all mstb marked as not probed after suspend/resume
+    - remoteproc: imx_rproc: Fix refcount mistake in imx_rproc_addr_init
+    - MIPS: Loongson64: DTS: Add RTC support to Loongson-2K1000
+    - MIPS: Loongson64: DTS: Fix PCIe port nodes for ls7a
+    - MIPS: dts: loongson: Fix liointc IRQ polarity
+    - MIPS: dts: loongson: Fix ls2k1000-rtc interrupt
+    - drm/nouveau: prime: fix refcount underflow
+    - drm/vmwgfx: Fix overlay when using Screen Targets
+    - sched: act_ct: take care of padding in struct zones_ht_key
+    - ALSA: hda: conexant: Fix headset auto detect fail in the polling mode
+    - rtnetlink: enable alt_ifname for setlink/newlink
+    - rtnetlink: Don't ignore IFLA_TARGET_NETNSID when ifname is specified in
+      rtnl_dellink().
+    - net/iucv: fix use after free in iucv_sock_close()
+    - net: mvpp2: Don't re-use loop iterator
+    - netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init().
+    - netfilter: iptables: Fix potential null-ptr-deref in
+      ip6table_nat_table_init().
+    - net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptys
+    - ipv6: fix ndisc_is_useropt() handling for PIO
+    - riscv/mm: Add handling for VM_FAULT_SIGSEGV in mm_fault_error()
+    - power: supply: bq24190_charger: replace deprecated strncpy with strscpy
+    - platform/chrome: cros_ec_proto: Lock device when updating MKBP version
+    - HID: wacom: Modify pen IDs
+    - protect the fetch of ->fd[fd] in do_dup2() from mispredictions
+    - ALSA: usb-audio: Correct surround channels in UAC1 channel map
+    - ALSA: hda/realtek: Add quirk for Acer Aspire E5-574G
+    - Revert "ALSA: firewire-lib: obsolete workqueue for period update"
+    - Revert "ALSA: firewire-lib: operate for period elapse event in process
+      context"
+    - drm/vmwgfx: Fix a deadlock in dma buf fence polling
+    - net: usb: sr9700: fix uninitialized variable use in sr_mdio_read
+    - r8169: don't increment tx_dropped in case of NETDEV_TX_BUSY
+    - mptcp: fix duplicate data handling
+    - netfilter: ipset: Add list flush to cancel_gc
+    - genirq: Allow irq_chip registration functions to take a const irq_chip
+    - irqchip/mbigen: Fix mbigen node address layout
+    - x86/mm: Fix pti_clone_pgtable() alignment assumption
+    - x86/mm: Fix pti_clone_entry_text() for i386
+    - sctp: move hlist_node and hashent out of sctp_ep_common
+    - sctp: Fix null-ptr-deref in reuseport_add_sock().
+    - net: usb: qmi_wwan: fix memory leak for not ip packets
+    - net: bridge: mcast: wait for previous gc cycles when removing port
+    - net: linkwatch: use system_unbound_wq
+    - Bluetooth: l2cap: always unlock channel in l2cap_conless_channel()
+    - net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register()
+    - l2tp: fix lockdep splat
+    - net: fec: Stop PPS on driver remove
+    - rcutorture: Fix rcu_torture_fwd_cb_cr() data race
+    - md: do not delete safemode_timer in mddev_suspend
+    - md/raid5: avoid BUG_ON() while continue reshape after reassembling
+    - clocksource/drivers/sh_cmt: Address race condition for clock events
+    - ACPI: battery: create alarm sysfs attribute atomically
+    - ACPI: SBS: manage alarm sysfs attribute through psy core
+    - selftests/bpf: Fix send_signal test with nested CONFIG_PARAVIRT
+    - PCI: Add Edimax Vendor ID to pci_ids.h
+    - udf: prevent integer overflow in udf_bitmap_free_blocks()
+    - wifi: nl80211: don't give key data to userspace
+    - btrfs: fix bitmap leak when loading free space cache on duplicate entry
+    - drm/amdgpu/pm: Fix the null pointer dereference for smu7
+    - drm/amdgpu: Fix the null pointer dereference to ras_manager
+    - drm/amdgpu/pm: Fix the null pointer dereference in apply_state_adjust_rules
+    - drm/amd/display: Add null checker before passing variables
+    - media: uvcvideo: Ignore empty TS packets
+    - media: uvcvideo: Fix the bandwdith quirk on USB 3.x
+    - ext4: fix uninitialized variable in ext4_inlinedir_to_tree
+    - jbd2: avoid memleak in jbd2_journal_write_metadata_buffer
+    - s390/sclp: Prevent release of buffer in I/O
+    - SUNRPC: Fix a race to wake a sync task
+    - profiling: remove profile=sleep support
+    - scsi: mpt3sas: Avoid IOMMU page faults on REPORT ZONES
+    - sched/cputime: Fix mul_u64_u64_div_u64() precision for cputime
+    - ext4: fix wrong unit use in ext4_mb_find_by_goal
+    - arm64: cpufeature: Force HWCAP to be based on the sysreg visible to user-
+      space
+    - arm64: Add Neoverse-V2 part
+    - arm64: barrier: Restore spec_bar() macro
+    - arm64: cputype: Add Cortex-X4 definitions
+    - arm64: cputype: Add Neoverse-V3 definitions
+    - arm64: errata: Add workaround for Arm errata 3194386 and 3312417
+    - [Config] Set ARM64_ERRATUM_3194386=y
+    - arm64: cputype: Add Cortex-X3 definitions
+    - arm64: cputype: Add Cortex-A720 definitions
+    - arm64: cputype: Add Cortex-X925 definitions
+    - arm64: errata: Unify speculative SSBS errata logic
+    - arm64: errata: Expand speculative SSBS workaround
+    - arm64: cputype: Add Cortex-X1C definitions
+    - arm64: cputype: Add Cortex-A725 definitions
+    - arm64: errata: Expand speculative SSBS workaround (again)
+    - i2c: smbus: Improve handling of stuck alerts
+    - ASoC: codecs: wcd938x-sdw: Correct Soundwire ports mask
+    - ASoC: codecs: wsa881x: Correct Soundwire ports mask
+    - spi: spidev: Add missing spi_device_id for bh2228fv
+    - i2c: smbus: Send alert notifications to all devices if source not found
+    - bpf: kprobe: remove unused declaring of bpf_kprobe_override
+    - kprobes: Fix to check symbol prefixes correctly
+    - spi: spi-fsl-lpspi: Fix scldiv calculation
+    - ALSA: usb-audio: Re-add ScratchAmp quirk entries
+    - ASoC: meson: axg-fifo: fix irq scheduling issue with PREEMPT_RT
+    - drm/client: fix null pointer dereference in drm_client_modeset_probe
+    - ALSA: line6: Fix racy access to midibuf
+    - ALSA: hda: Add HP MP9 G4 Retail System AMS to force connect list
+    - ALSA: hda/hdmi: Yet more pin fix for HP EliteDesk 800 G4
+    - usb: vhci-hcd: Do not drop references before new references are gained
+    - USB: serial: debug: do not echo input by default
+    - usb: gadget: core: Check for unset descriptor
+    - usb: gadget: u_serial: Set start_delayed during suspend
+    - scsi: mpi3mr: Avoid IOMMU page faults on REPORT ZONES
+    - scsi: ufs: core: Fix hba->last_dme_cmd_tstamp timestamp updating logic
+    - tick/broadcast: Move per CPU pointer access into the atomic section
+    - vhost-vdpa: switch to use vmf_insert_pfn() in the fault handler
+    - ntp: Clamp maxerror and esterror to operating range
+    - clocksource: Reduce the default clocksource_watchdog() retries to 2
+    - torture: Enable clocksource watchdog with "tsc=watchdog"
+    - clocksource: Scale the watchdog read retries automatically
+    - clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()
+    - irqchip/meson-gpio: support more than 8 channels gpio irq
+    - irqchip/meson-gpio: Convert meson_gpio_irq_controller::lock to
+      'raw_spinlock_t'
+    - driver core: Fix uevent_show() vs driver detach race
+    - ntp: Safeguard against time_constant overflow
+    - timekeeping: Fix bogus clock_was_set() invocation in do_adjtimex()
+    - serial: core: check uartclk for zero to avoid divide by zero
+    - kcov: properly check for softirq context
+    - irqchip/xilinx: Fix shift out of bounds
+    - genirq/irqdesc: Honor caller provided affinity in alloc_desc()
+    - power: supply: axp288_charger: Fix constant_charge_voltage writes
+    - power: supply: axp288_charger: Round constant_charge_voltage writes down
+    - tracing: Fix overflow in get_free_elt()
+    - padata: Fix possible divide-by-0 panic in padata_mt_helper()
+    - x86/mtrr: Check if fixed MTRRs exist before saving them
+    - sched/smt: Introduce sched_smt_present_inc/dec() helper
+    - sched/smt: Fix unbalance sched_smt_present dec/inc
+    - drm/bridge: analogix_dp: properly handle zero sized AUX transactions
+    - drm/mgag200: Set DDC timeout in milliseconds
+    - mptcp: sched: check both directions for backup
+    - mptcp: distinguish rcv vs sent backup flag in requests
+    - mptcp: fix NL PM announced address accounting
+    - mptcp: mib: count MPJ with backup flag
+    - mptcp: fix bad RCVPRUNED mib accounting
+    - mptcp: pm: only set request_bkup flag when sending MP_PRIO
+    - mptcp: export local_address
+    - mptcp: pm: fix backup support in signal endpoints
+    - selftests: mptcp: join: validate backup in MPJ
+    - selftests: mptcp: join: check backup support in signal endp
+    - btrfs: fix corruption after buffer fault in during direct IO append write
+    - xfs: fix log recovery buffer allocation for the legacy h_size fixup
+    - btrfs: fix double inode unlock for direct IO sync writes
+    - PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal
+    - netfilter: nf_tables: set element extended ACK reporting support
+    - netfilter: nf_tables: bail out if stateful expression provides no .clone
+    - netfilter: nf_tables: allow clone callbacks to sleep
+    - netfilter: nf_tables: prefer nft_chain_validate
+    - net: stmmac: Enable mac_managed_pm phylink config
+    - PCI: dwc: Restore MSI Receiver mask during resume
+    - wifi: mac80211: check basic rates validity
+    - mptcp: fully established after ADD_ADDR echo on MPJ
+    - drm/i915/gem: Fix Virtual Memory mapping boundaries calculation
+    - powerpc: Avoid nmi_enter/nmi_exit in real mode interrupt.
+    - arm64: dts: qcom: msm8996: correct #clock-cells for QMP PHY nodes
+    - arm64: cpufeature: Fix the visibility of compat hwcaps
+    - exec: Fix ToCToU between perm check and set-uid/gid usage
+    - nvme/pci: Add APST quirk for Lenovo N60z laptop
+    - usb: gadget: u_audio: Check return codes from usb_ep_enable and
+      config_ep_by_speed.
+    - binfmt_flat: Fix corruption when not offsetting data start
+    - wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values
+    - ARM: dts: imx6qdl-kontron-samx6i: fix phy-mode
+    - media: Revert "media: dvb-usb: Fix unexpected infinite loop in
+      dvb_usb_read_remote_control()"
+    - Revert "ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error"
+    - Linux 5.15.165
+  * CVE-2024-26661
+    - drm/amd/display: Add NULL test for 'timing generator' in 'dcn21_set_pipe()'
+  * CVE-2024-25744
+    - x86: Fix misspelled Kconfig symbols
+    - x86: Introduce ia32_enabled()
+    - x86/sev: Rename mem_encrypt.c to mem_encrypt_amd.c
+    - x86/coco: Disable 32-bit emulation by default on TDX and SEV
+    - x86/entry: Convert INT 0x80 emulation to IDTENTRY
+    - x86/entry: Do not allow external 0x80 interrupts
+    - x86/entry: Add do_SYSENTER_32() prototype
+    - x86/bhi: Add support for clearing branch history at syscall entry
+  * [UBUNTU 22.04] s390/cpum_cf: make crypto counters upward compatible
+    (LP: #2074380)
+    - s390/cpum_cf: make crypto counters upward compatible across machine types
+  * Jammy update: v5.15.164 upstream stable release (LP: #2076100)
+    - gcc-plugins: Rename last_stmt() for GCC 14+
+    - filelock: Remove locks reliably when fcntl/close race is detected
+    - ARM: 9324/1: fix get_user() broken with veneer
+    - ACPI: processor_idle: Fix invalid comparison with insertion sort for latency
+    - scsi: core: Fix a use-after-free
+    - scsi: core: alua: I/O errors for ALUA state transitions
+    - scsi: qedf: Don't process stag work during unload and recovery
+    - scsi: qedf: Wait for stag work during unload
+    - scsi: qedf: Set qed_slowpath_params to zero before use
+    - ACPI: EC: Abort address space access upon error
+    - ACPI: EC: Avoid returning AE_OK on errors in address space handler
+    - tools/power/cpupower: Fix Pstate frequency reporting on AMD Family 1Ah CPUs
+    - wifi: mac80211: mesh: init nonpeer_pm to active by default in mesh sdata
+    - wifi: mac80211: handle tasklet frames before stopping
+    - wifi: iwlwifi: mvm: d3: fix WoWLAN command version lookup
+    - wifi: iwlwifi: mvm: Handle BIGTK cipher in kek_kck cmd
+    - wifi: iwlwifi: mvm: properly set 6 GHz channel direct probe option
+    - wifi: mac80211: fix UBSAN noise in ieee80211_prep_hw_scan()
+    - selftests/openat2: Fix build warnings on ppc64
+    - Input: silead - Always support 10 fingers
+    - net: ipv6: rpl_iptunnel: block BH in rpl_output() and rpl_input()
+    - ila: block BH in ila_output()
+    - arm64: armv8_deprecated: Fix warning in isndep cpuhp starting process
+    - null_blk: fix validation of block size
+    - kconfig: gconf: give a proper initial state to the Save button
+    - kconfig: remove wrong expr_trans_bool()
+    - fs/file: fix the check in find_next_fd()
+    - mei: demote client disconnect warning on suspend to debug
+    - nvme: avoid double free special payload
+    - wifi: cfg80211: wext: add extra SIOCSIWSCAN data check
+    - KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group()
+    - drm/vmwgfx: Fix missing HYPERVISOR_GUEST dependency
+    - ALSA: hda/realtek: Add more codec ID to no shutup pins list
+    - mips: fix compat_sys_lseek syscall
+    - Input: elantech - fix touchpad state on resume for Lenovo N24
+    - Input: i8042 - add Ayaneo Kun to i8042 quirk table
+    - bytcr_rt5640 : inverse jack detect for Archos 101 cesium
+    - ALSA: dmaengine: Synchronize dma channel after drop()
+    - ASoC: ti: davinci-mcasp: Set min period size using FIFO config
+    - ASoC: ti: omap-hdmi: Fix too long driver name
+    - can: kvaser_usb: fix return value for hif_usb_send_regout
+    - s390/sclp: Fix sclp_init() cleanup on failure
+    - platform/x86: wireless-hotkey: Add support for LG Airplane Button
+    - platform/x86: lg-laptop: Remove LGEX0815 hotkey handling
+    - platform/x86: lg-laptop: Change ACPI device id
+    - platform/x86: lg-laptop: Use ACPI device handle when evaluating WMAB/WMBB
+    - btrfs: qgroup: fix quota root leak after quota disable failure
+    - ALSA: hda/relatek: Enable Mute LED on HP Laptop 15-gw0xxx
+    - ALSA: dmaengine_pcm: terminate dmaengine before synchronize
+    - net: usb: qmi_wwan: add Telit FN912 compositions
+    - net: mac802154: Fix racy device stats updates by DEV_STATS_INC() and
+      DEV_STATS_ADD()
+    - powerpc/pseries: Whitelist dtl slub object for copying to userspace
+    - powerpc/eeh: avoid possible crash when edev->pdev changes
+    - scsi: libsas: Fix exp-attached device scan after probe failure scanned in
+      again after probe failed
+    - Bluetooth: hci_core: cancel all works upon hci_unregister_dev()
+    - drm/radeon: check bo_va->bo is non-NULL before using it
+    - fs: better handle deep ancestor chains in is_subdir()
+    - riscv: stacktrace: fix usage of ftrace_graph_ret_addr()
+    - spi: imx: Don't expect DMA for i.MX{25,35,50,51,53} cspi devices
+    - selftests/vDSO: fix clang build errors and warnings
+    - hfsplus: fix uninit-value in copy_name
+    - spi: mux: set ctlr->bits_per_word_mask
+    - tracing: Define the is_signed_type() macro once
+    - minmax: sanity check constant bounds when clamping
+    - minmax: clamp more efficiently by avoiding extra comparison
+    - minmax: fix header inclusions
+    - minmax: allow min()/max()/clamp() if the arguments have the same signedness.
+    - minmax: allow comparisons of 'int' against 'unsigned char/short'
+    - minmax: relax check to allow comparison between unsigned arguments and
+      signed constants
+    - mm/damon/core: merge regions aggressively when max_nr_regions is unmet
+    - wifi: mac80211: disable softirqs for queued frame handling
+    - drm/amdgpu: Fix signedness bug in sdma_v4_0_process_trap_irq()
+    - samples: Add fs error monitoring example
+    - samples: Make fs-monitor depend on libc and headers
+    - docs: Fix formatting of literal sections in fanotify docs
+    - Add gitignore file for samples/fanotify/ subdirectory
+    - net: relax socket state check at accept time.
+    - ocfs2: add bounds checking to ocfs2_check_dir_entry()
+    - jfs: don't walk off the end of ealist
+    - fs/ntfs3: Validate ff offset
+    - ALSA: hda/realtek: Enable headset mic on Positivo SU C1400
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
+    - arm64: dts: qcom: msm8996: Disable SS instance in Parkmode for USB
+    - arm64: dts: qcom: sdm630: Disable SS instance in Parkmode for USB
+    - ALSA: pcm_dmaengine: Don't synchronize DMA channel when DMA is paused
+    - filelock: Fix fcntl/close race recovery compat path
+    - wifi: rt2x00: use explicitly signed or unsigned types
+    - tun: add missing verification for short frame
+    - tap: add missing verification for short frame
+    - Linux 5.15.164
+  * Jammy update: v5.15.166 upstream stable release (LP: #2080594) //
+    CVE-2024-45016
+    - netem: fix return value if duplicate enqueue fails
+  * CVE-2024-38630
+    - watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
+  * CVE-2024-27397
+    - netfilter: nf_tables: use timestamp to check for set element timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 09 Oct 2024 09:43:42 +1000
+
+linux-xilinx-zynqmp (5.15.0-1037.41) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1037.41 -proposed tracker (LP: #2082173)
+
+  [ Ubuntu: 5.15.0-124.134 ]
+
+  * jammy/linux: 5.15.0-124.134 -proposed tracker (LP: #2082176)
+  * CVE-2024-45016
+    - netem: fix return value if duplicate enqueue fails
+  * CVE-2024-38630
+    - watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
+  * CVE-2024-27397
+    - netfilter: nf_tables: use timestamp to check for set element timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 04 Oct 2024 08:16:14 +1000
+
+linux-xilinx-zynqmp (5.15.0-1036.40) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1036.40 -proposed tracker (LP: #2078151)
+
+  [ Ubuntu: 5.15.0-122.132 ]
+
+  * jammy/linux: 5.15.0-122.132 -proposed tracker (LP: #2078154)
+  * isolcpus are ignored when using cgroups V2, causing processes to have wrong
+    affinity (LP: #2076957)
+    - cgroup/cpuset: Optimize cpuset_attach() on v2
+  * Jammy update: v5.15.164 upstream stable release (LP: #2076100) //
+    CVE-2024-41009
+    - bpf: Fix overrunning reservations in ringbuf
+  * CVE-2024-39494
+    - ima: Fix use-after-free on a dentry's dname.name
+  * CVE-2024-39496
+    - btrfs: zoned: fix use-after-free due to race with dev replace
+  * CVE-2024-42160
+    - f2fs: check validation of fault attrs in f2fs_build_fault_attr()
+    - f2fs: Add inline to f2fs_build_fault_attr() stub
+  * CVE-2024-38570
+    - gfs2: Rename sd_{ glock => kill }_wait
+    - gfs2: Fix potential glock use-after-free on unmount
+  * CVE-2024-42228
+    - drm/amdgpu: Using uninitialized value *size when calling amdgpu_vce_cs_reloc
+  * CVE-2024-27012
+    - netfilter: nf_tables: restore set elements when delete set fails
+  * CVE-2024-26677
+    - rxrpc: Fix delayed ACKs to not set the reference serial number
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Tue, 03 Sep 2024 14:32:49 +0200
+
+linux-xilinx-zynqmp (5.15.0-1035.39) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1035.39 -proposed tracker (LP: #2077835)
+
+  * Backport ps uart  RS485  driver  (LP: #2055237)
+    - dt-bindings: serial: cdsn,uart: add power-domains
+    - dt-bindings: Add reference to rs485.yaml
+    - serial: Store character timing information to uart_port
+    - serial: take termios_rwsem for ->rs485_config() & pass termios as param
+    - tty: serial: uartps: Relocate cdns_uart_tx_empty to facilitate rs485
+    - tty: serial: uartps: Add rs485 support to uartps driver
+    - dt-bindings: serial: cdns,uart: Add optional reset property
+    - arm64: zynqmp: Add resets property for UART nodes
+    - tty: serial: uartps: Add support for uartps controller reset
+    - SAUCE: dts: zynqmp-sck-kd-g-revA: Enable uart0 for KD240
+    - SAUCE: arm64: zynqmp: dts: Add required properties for rs485 support for
+      KD240
+    - SAUCE: arm64: zynqmp: dts: Add rts delay property for rs485 mode on KD240
+    - serial: 8250: Document termios parameter of serial8250_em485_config()
+    - serial: fix TIOCSRS485 locking
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Mon, 26 Aug 2024 09:21:51 +1000
+
+linux-xilinx-zynqmp (5.15.0-1034.38) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1034.38 -proposed tracker (LP: #2075900)
+
+  * Update IMX547 out-of-tree driver code (LP: #2076108)
+    - SAUCE: imx547 : Used devm_* resource management functions instead of gpiod_*
+
+  [ Ubuntu: 5.15.0-121.131 ]
+
+  * jammy/linux: 5.15.0-121.131 -proposed tracker (LP: #2076347)
+  * jammy:linux bpf selftest do not build (LP: #2076334)
+    - SAUCE: Revert "bpf: Allow reads from uninit stack"
+
+  [ Ubuntu: 5.15.0-120.130 ]
+
+  * jammy/linux: 5.15.0-120.130 -proposed tracker (LP: #2075903)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2024.08.05)
+  * Jammy update: v5.15.163 upstream stable release (LP: #2075170)
+    - Compiler Attributes: Add __uninitialized macro
+    - locking/mutex: Introduce devm_mutex_init()
+    - drm/lima: fix shared irq handling on driver remove
+    - media: dvb: as102-fe: Fix as10x_register_addr packing
+    - media: dvb-usb: dib0700_devices: Add missing release_firmware()
+    - IB/core: Implement a limit on UMAD receive List
+    - scsi: qedf: Make qedf_execute_tmf() non-preemptible
+    - crypto: aead,cipher - zeroize key buffer after use
+    - drm/amdgpu: Initialize timestamp for some legacy SOCs
+    - drm/amd/display: Check index msg_id before read or write
+    - drm/amd/display: Check pipe offset before setting vblank
+    - drm/amd/display: Skip finding free audio for unknown engine_id
+    - media: dw2102: Don't translate i2c read into write
+    - sctp: prefer struct_size over open coded arithmetic
+    - firmware: dmi: Stop decoding on broken entry
+    - Input: ff-core - prefer struct_size over open coded arithmetic
+    - wifi: mt76: replace skb_put with skb_put_zero
+    - net: dsa: mv88e6xxx: Correct check for empty list
+    - media: dvb-frontends: tda18271c2dd: Remove casting during div
+    - media: s2255: Use refcount_t instead of atomic_t for num_channels
+    - media: dvb-frontends: tda10048: Fix integer overflow
+    - i2c: i801: Annotate apanel_addr as __ro_after_init
+    - powerpc/64: Set _IO_BASE to POISON_POINTER_DELTA not 0 for CONFIG_PCI=n
+    - orangefs: fix out-of-bounds fsid access
+    - kunit: Fix timeout message
+    - powerpc/xmon: Check cpu id in commands "c#", "dp#" and "dx#"
+    - igc: fix a log entry using uninitialized netdev
+    - bpf: Avoid uninitialized value in BPF_CORE_READ_BITFIELD
+    - jffs2: Fix potential illegal address access in jffs2_free_inode
+    - s390/pkey: Wipe sensitive data on failure
+    - tools/power turbostat: Remember global max_die_id
+    - UPSTREAM: tcp: fix DSACK undo in fast recovery to call tcp_try_to_open()
+    - tcp_metrics: validate source addr length
+    - KVM: s390: fix LPSWEY handling
+    - e1000e: Fix S0ix residency on corporate systems
+    - net: allow skb_datagram_iter to be called from any context
+    - wifi: wilc1000: fix ies_len type in connect path
+    - riscv: kexec: Avoid deadlock in kexec crash path
+    - netfilter: nf_tables: unconditionally flush pending work before notifier
+    - bonding: Fix out-of-bounds read in bond_option_arp_ip_targets_set()
+    - selftests: fix OOM in msg_zerocopy selftest
+    - selftests: make order checking verbose in msg_zerocopy selftest
+    - inet_diag: Initialize pad field in struct inet_diag_req_v2
+    - gpiolib: of: factor out code overriding gpio line polarity
+    - gpiolib: of: add a quirk for reset line polarity for Himax LCDs
+    - gpiolib: of: add polarity quirk for TSC2005
+    - Revert "igc: fix a log entry using uninitialized netdev"
+    - nilfs2: fix inode number range checks
+    - nilfs2: add missing check for inode numbers on directory entries
+    - mm: optimize the redundant loop of mm_update_owner_next()
+    - mm: avoid overflows in dirty throttling logic
+    - btrfs: fix adding block group to a reclaim list and the unused list during
+      reclaim
+    - Bluetooth: qca: Fix BT enable failure again for QCA6390 after warm reboot
+    - can: kvaser_usb: Explicitly initialize family in leafimx driver_info struct
+    - fsnotify: Do not generate events for O_PATH file descriptors
+    - Revert "mm/writeback: fix possible divide-by-zero in wb_dirty_limits(),
+      again"
+    - drm/nouveau: fix null pointer dereference in nouveau_connector_get_modes
+    - drm/amdgpu/atomfirmware: silence UBSAN warning
+    - mtd: rawnand: Ensure ECC configuration is propagated to upper layers
+    - mtd: rawnand: Bypass a couple of sanity checks during NAND identification
+    - mtd: rawnand: rockchip: ensure NVDDR timings are rejected
+    - ima: Avoid blocking in RCU read-side critical section
+    - media: dw2102: fix a potential buffer overflow
+    - clk: qcom: gcc-sm6350: Fix gpll6* & gpll7 parents
+    - i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr
+    - fs/ntfs3: Mark volume as dirty if xattr is broken
+    - ALSA: hda/realtek: Enable headset mic of JP-IK LEAP W502 with ALC897
+    - nvme-multipath: find NUMA path only for online numa-node
+    - dma-mapping: benchmark: avoid needless copy_to_user if benchmark fails
+    - nvme: adjust multiples of NVME_CTRL_PAGE_SIZE in offset
+    - regmap-i2c: Subtract reg size from max_write
+    - platform/x86: touchscreen_dmi: Add info for GlobalSpace SolT IVW 11.6"
+      tablet
+    - platform/x86: touchscreen_dmi: Add info for the EZpad 6s Pro
+    - nvmet: fix a possible leak when destroy a ctrl during qp establishment
+    - kbuild: fix short log for AS in link-vmlinux.sh
+    - nfc/nci: Add the inconsistency check between the input data length and count
+    - null_blk: Do not allow runt zone with zone capacity smaller then zone size
+    - nilfs2: fix incorrect inode allocation from reserved inodes
+    - mm: prevent derefencing NULL ptr in pfn_section_valid()
+    - filelock: fix potential use-after-free in posix_lock_inode
+    - fs/dcache: Re-use value stored to dentry->d_flags instead of re-reading
+    - vfs: don't mod negative dentry count when on shrinker list
+    - tcp: fix incorrect undo caused by DSACK of TLP retransmit
+    - skmsg: Skip zero length skb in sk_msg_recvmsg
+    - octeontx2-af: Fix incorrect value output on error path in
+      rvu_check_rsrc_availability()
+    - net: fix rc7's __skb_datagram_iter()
+    - i40e: Fix XDP program unloading while removing the driver
+    - net: lantiq_etop: add blank line after declaration
+    - net: ethernet: lantiq_etop: fix double free in detach
+    - net: ethernet: mtk-star-emac: set mac_managed_pm when probing
+    - ppp: reject claimed-as-LCP but actually malformed packets
+    - ethtool: netlink: do not return SQI value if link is down
+    - udp: Set SOCK_RCU_FREE earlier in udp_lib_get_port().
+    - s390: Mark psw in __load_psw_mask() as __unitialized
+    - ARM: davinci: Convert comma to semicolon
+    - octeontx2-af: replace cpt slot with lf id on reg write
+    - octeontx2-af: update cpt lf alloc mailbox
+    - octeontx2-af: fix a issue with cpt_lf_alloc mailbox
+    - octeontx2-af: fix detection of IP layer
+    - octeontx2-af: extend RSS supported offload types
+    - octeontx2-af: fix issue with IPv6 ext match for RSS
+    - octeontx2-af: fix issue with IPv4 match for RSS
+    - tcp: use signed arithmetic in tcp_rtx_probe0_timed_out()
+    - tcp: avoid too many retransmit packets
+    - net: ks8851: Fix potential TX stall after interface reopen
+    - USB: serial: option: add Telit generic core-dump composition
+    - USB: serial: option: add Telit FN912 rmnet compositions
+    - USB: serial: option: add Fibocom FM350-GL
+    - USB: serial: option: add support for Foxconn T99W651
+    - USB: serial: option: add Netprisma LCUK54 series modules
+    - USB: serial: option: add Rolling RW350-GL variants
+    - USB: serial: mos7840: fix crash on resume
+    - USB: Add USB_QUIRK_NO_SET_INTF quirk for START BP-850k
+    - usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()
+    - USB: core: Fix duplicate endpoint bug by clearing reserved bits in the
+      descriptor
+    - hpet: Support 32-bit userspace
+    - nvmem: rmem: Fix return value of rmem_read()
+    - nvmem: meson-efuse: Fix return value of nvmem callbacks
+    - nvmem: core: only change name to fram for current attribute
+    - ALSA: hda/realtek: add quirk for Clevo V5[46]0TU
+    - ALSA: hda/realtek: Enable Mute LED on HP 250 G7
+    - ALSA: hda/realtek: Limit mic boost on VAIO PRO PX
+    - Fix userfaultfd_api to return EINVAL as expected
+    - libceph: fix race between delayed_work() and ceph_monc_stop()
+    - wireguard: allowedips: avoid unaligned 64-bit memory accesses
+    - wireguard: queueing: annotate intentional data race in cpu round robin
+    - wireguard: send: annotate intentional data race in checking empty queue
+    - ipv6: annotate data-races around cnf.disable_ipv6
+    - bpf: Allow reads from uninit stack
+    - nilfs2: fix kernel bug on rename operation of broken directory
+    - i2c: rcar: bring hardware to known state when probing
+    - i2c: mark HostNotify target address as used
+    - i2c: rcar: Add R-Car Gen4 support
+    - i2c: rcar: reset controller is mandatory for Gen3+
+    - i2c: rcar: introduce Gen4 devices
+    - i2c: rcar: ensure Gen3+ reset does not disturb local targets
+    - i2c: testunit: avoid re-issued work after read message
+    - i2c: rcar: clear NO_RXDMA flag after resetting
+    - x86/entry/64: Remove obsolete comment on tracing vs. SYSRET
+    - x86/bhi: Avoid warning in #DB handler due to BHI mitigation
+    - kbuild: Make ld-version.sh more robust against version string changes
+    - i2c: rcar: fix error code in probe()
+    - Linux 5.15.163
+  * [SRU] UBSAN warnings in bnx2x kernel driver (LP: #2074215) // Jammy update:
+    v5.15.163 upstream stable release (LP: #2075170)
+    - bnx2x: Fix multiple UBSAN array-index-out-of-bounds
+  * Jammy update: v5.15.162 upstream stable release (LP: #2073765)
+    - mmc: davinci_mmc: Convert to platform remove callback returning void
+    - wifi: mac80211: mesh: Fix leak of mesh_preq_queue objects
+    - wifi: mac80211: Fix deadlock in ieee80211_sta_ps_deliver_wakeup()
+    - wifi: cfg80211: Lock wiphy in cfg80211_get_station
+    - wifi: cfg80211: pmsr: use correct nla_get_uX functions
+    - wifi: iwlwifi: mvm: revert gen2 TX A-MPDU size to 64
+    - wifi: iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
+    - wifi: iwlwifi: mvm: check n_ssids before accessing the ssids
+    - wifi: iwlwifi: mvm: don't read past the mfuart notifcation
+    - wifi: mac80211: correctly parse Spatial Reuse Parameter Set element
+    - net/ncsi: Simplify Kconfig/dts control flow
+    - net/ncsi: Fix the multi thread manner of NCSI driver
+    - ipv6: sr: block BH in seg6_output_core() and seg6_input_core()
+    - bpf: Set run context for rawtp test_run callback
+    - octeontx2-af: Always allocate PF entries from low prioriy zone
+    - net: sched: sch_multiq: fix possible OOB write in multiq_tune()
+    - vxlan: Fix regression when dropping packets due to invalid src addresses
+    - tcp: count CLOSE-WAIT sockets for TCP_MIB_CURRESTAB
+    - net/sched: taprio: always validate TCA_TAPRIO_ATTR_PRIOMAP
+    - ptp: Fix error message on failed pin verification
+    - af_unix: Set sk->sk_state under unix_state_lock() for truly disconencted
+      peer.
+    - af_unix: Annodate data-races around sk->sk_state for writers.
+    - af_unix: Annotate data-race of sk->sk_state in unix_inq_len().
+    - af_unix: Annotate data-races around sk->sk_state in unix_write_space() and
+      poll().
+    - net: inline sock_prot_inuse_add()
+    - net: drop nopreempt requirement on sock_prot_inuse_add()
+    - af_unix: Annotate data-race of sk->sk_state in unix_stream_connect().
+    - af_unix: Annotate data-races around sk->sk_state in sendmsg() and recvmsg().
+    - af_unix: Annotate data-race of sk->sk_state in unix_stream_read_skb().
+    - af_unix: Annotate data-races around sk->sk_state in UNIX_DIAG.
+    - af_unix: Annotate data-race of net->unx.sysctl_max_dgram_qlen.
+    - af_unix: Use unix_recvq_full_lockless() in unix_stream_connect().
+    - af_unix: annotate lockless accesses to sk->sk_err
+    - af_unix: Use skb_queue_empty_lockless() in unix_release_sock().
+    - af_unix: Use skb_queue_len_lockless() in sk_diag_show_rqlen().
+    - af_unix: Annotate data-race of sk->sk_shutdown in sk_diag_fill().
+    - ipv6: fix possible race in __fib6_drop_pcpu_from()
+    - usb: gadget: f_fs: use io_data->status consistently
+    - usb: gadget: f_fs: Fix race between aio_cancel() and AIO request complete
+    - iio: accel: mxc4005: Reset chip on probe() and resume()
+    - drm/amd/display: Handle Y carry-over in VCP X.Y calculation
+    - drm/amd/display: Clean up some inconsistent indenting
+    - drm/amd/display: drop unnecessary NULL checks in debugfs
+    - drm/amd/display: Fix incorrect DSC instance for MST
+    - pvpanic: Keep single style across modules
+    - pvpanic: Indentation fixes here and there
+    - misc/pvpanic: deduplicate common code
+    - misc/pvpanic-pci: register attributes via pci_driver
+    - skbuff: introduce skb_pull_data
+    - Bluetooth: hci_qca: mark OF related data as maybe unused
+    - Bluetooth: btqca: use le32_to_cpu for ver.soc_id
+    - Bluetooth: btqca: Add WCN3988 support
+    - Bluetooth: qca: use switch case for soc type behavior
+    - Bluetooth: qca: add support for QCA2066
+    - Bluetooth: qca: fix info leak when fetching fw build id
+    - serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
+    - serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
+    - x86/ibt,ftrace: Search for __fentry__ location
+    - ftrace: Fix possible use-after-free issue in ftrace_location()
+    - i2c: add fwnode APIs
+    - i2c: acpi: Unbind mux adapters before delete
+    - cma: factor out minimum alignment requirement
+    - mm/cma: drop incorrect alignment check in cma_init_reserved_mem
+    - selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
+    - selftests/mm: conform test to TAP format output
+    - selftests/mm: compaction_test: fix bogus test success on Aarch64
+    - wifi: ath10k: fix QCOM_RPROC_COMMON dependency
+    - btrfs: fix leak of qgroup extent records after transaction abort
+    - nilfs2: Remove check for PageError
+    - nilfs2: return the mapped address from nilfs_get_page()
+    - nilfs2: fix nilfs_empty_dir() misjudgment and long loop on I/O errors
+    - USB: class: cdc-wdm: Fix CPU lockup caused by excessive log messages
+    - usb: typec: tcpm: Ignore received Hard Reset in TOGGLING state
+    - mei: me: release irq in mei_me_pci_resume error path
+    - jfs: xattr: fix buffer overflow for invalid xattr
+    - xhci: Set correct transferred length for cancelled bulk transfers
+    - xhci: Apply reset resume quirk to Etron EJ188 xHCI host
+    - xhci: Handle TD clearing for multiple streams case
+    - xhci: Apply broken streams quirk to Etron EJ188 xHCI host
+    - scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
+    - powerpc/uaccess: Fix build errors seen with GCC 13/14
+    - Input: try trimming too long modalias strings
+    - clk: sifive: Do not register clkdevs for PRCI clocks
+    - SUNRPC: return proper error from gss_wrap_req_priv
+    - platform/x86: dell-smbios-base: Use sysfs_emit()
+    - platform/x86: dell-smbios: Fix wrong token data in sysfs
+    - gpio: tqmx86: fix typo in Kconfig label
+    - gpio: tqmx86: store IRQ trigger type and unmask status separately
+    - HID: core: remove unnecessary WARN_ON() in implement()
+    - iommu/amd: Introduce pci segment structure
+    - iommu/amd: Fix sysfs leak in iommu init
+    - iommu: Return right value in iommu_sva_bind_device()
+    - HID: logitech-dj: Fix memory leak in logi_dj_recv_switch_to_dj_mode()
+    - drm/vmwgfx: 3D disabled should not effect STDU memory limits
+    - net: sfp: Always call `sfp_sm_mod_remove()` on remove
+    - net: hns3: fix kernel crash problem in concurrent scenario
+    - net: hns3: add cond_resched() to hns3 ring buffer init process
+    - liquidio: Adjust a NULL pointer handling path in lio_vf_rep_copy_packet
+    - drm/komeda: check for error-valued pointer
+    - drm/bridge/panel: Fix runtime warning on panel bridge release
+    - tcp: fix race in tcp_v6_syn_recv_sock()
+    - net/mlx5e: Fix features validation check for tunneled UDP (non-VXLAN)
+      packets
+    - netfilter: ipset: Fix race between namespace cleanup and gc in the list:set
+      type
+    - net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs
+      parameters
+    - net/ipv6: Fix the RT cache flush via sysctl using a previous delay
+    - ionic: fix use after netif_napi_del()
+    - af_unix: Read with MSG_PEEK loops if the first unread byte is OOB
+    - iio: adc: ad9467: fix scan type sign
+    - iio: dac: ad5592r: fix temperature channel scaling value
+    - iio: imu: inv_icm42600: delete unneeded update watermark call
+    - drivers: core: synchronize really_probe() and dev_uevent()
+    - drm/exynos/vidi: fix memory leak in .get_modes()
+    - drm/exynos: hdmi: report safe 640x480 mode as a fallback when no EDID found
+    - mptcp: ensure snd_una is properly initialized on connect
+    - tracing/selftests: Fix kprobe event name test for .isra. functions
+    - null_blk: Print correct max open zones limit in null_init_zoned_dev()
+    - sock_map: avoid race between sock_map_close and sk_psock_put
+    - vmci: prevent speculation leaks by sanitizing event in event_deliver()
+    - spmi: hisi-spmi-controller: Do not override device identifier
+    - knfsd: LOOKUP can return an illegal error value
+    - fs/proc: fix softlockup in __read_vmcore
+    - ocfs2: use coarse time for new created files
+    - ocfs2: fix races between hole punching and AIO+DIO
+    - PCI: rockchip-ep: Remove wrong mask on subsys_vendor_id
+    - dmaengine: axi-dmac: fix possible race in remove()
+    - intel_th: pci: Add Granite Rapids support
+    - intel_th: pci: Add Granite Rapids SOC support
+    - intel_th: pci: Add Sapphire Rapids SOC support
+    - intel_th: pci: Add Meteor Lake-S support
+    - intel_th: pci: Add Lunar Lake support
+    - nilfs2: fix potential kernel bug due to lack of writeback flag waiting
+    - tick/nohz_full: Don't abuse smp_call_function_single() in
+      tick_setup_device()
+    - scsi: mpi3mr: Fix ATA NCQ priority support
+    - mm/huge_memory: don't unpoison huge_zero_folio
+    - serial: 8250_pxa: Configure tx_loadsz to match FIFO IRQ level
+    - hugetlb_encode.h: fix undefined behaviour (34 << 26)
+    - mptcp: pm: inc RmAddr MIB counter once per RM_ADDR ID
+    - mptcp: pm: update add_addr counters after connect
+    - kbuild: Remove support for Clang's ThinLTO caching
+    - greybus: Fix use-after-free bug in gb_interface_release due to race
+      condition.
+    - usb-storage: alauda: Check whether the media is initialized
+    - i2c: at91: Fix the functionality flags of the slave-only interface
+    - i2c: designware: Fix the functionality flags of the slave-only interface
+    - zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
+    - Bluetooth: qca: Fix error code in qca_read_fw_build_info()
+    - Bluetooth: qca: fix info leak when fetching board id
+    - padata: Disable BH when taking works lock on MT path
+    - crypto: hisilicon/sec - Fix memory leak for sec resource release
+    - rcutorture: Fix rcu_torture_one_read() pipe_count overflow comment
+    - rcutorture: Make stall-tasks directly exit when rcutorture tests end
+    - rcutorture: Fix invalid context warning when enable srcu barrier testing
+    - block/ioctl: prefer different overflow check
+    - selftests/bpf: Prevent client connect before server bind in
+      test_tc_tunnel.sh
+    - selftests/bpf: Fix flaky test btf_map_in_map/lookup_update
+    - batman-adv: bypass empty buckets in batadv_purge_orig_ref()
+    - wifi: ath9k: work around memset overflow warning
+    - af_packet: avoid a false positive warning in packet_setsockopt()
+    - drop_monitor: replace spin_lock by raw_spin_lock
+    - scsi: qedi: Fix crash while reading debugfs attribute
+    - kselftest: arm64: Add a null pointer check
+    - netpoll: Fix race condition in netpoll_owner_active
+    - HID: Add quirk for Logitech Casa touchpad
+    - ACPI: video: Add backlight=native quirk for Lenovo Slim 7 16ARH7
+    - Bluetooth: ath3k: Fix multiple issues reported by checkpatch.pl
+    - drm/amd/display: Exit idle optimizations before HDCP execution
+    - drm/lima: add mask irq callback to gp and pp
+    - drm/lima: mask irqs in timeout path before hard reset
+    - powerpc/pseries: Enforce hcall result buffer validity and size
+    - powerpc/io: Avoid clang null pointer arithmetic warnings
+    - power: supply: cros_usbpd: provide ID table for avoiding fallback match
+    - iommu/arm-smmu-v3: Free MSIs in case of ENOMEM
+    - f2fs: remove clear SB_INLINECRYPT flag in default_options
+    - usb: misc: uss720: check for incompatible versions of the Belkin F5U002
+    - Avoid hw_desc array overrun in dw-axi-dmac
+    - udf: udftime: prevent overflow in udf_disk_stamp_to_time()
+    - PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports
+    - MIPS: Octeon: Add PCIe link status check
+    - serial: imx: Introduce timeout when waiting on transmitter empty
+    - serial: exar: adding missing CTI and Exar PCI ids
+    - MIPS: Routerboard 532: Fix vendor retry check code
+    - mips: bmips: BCM6358: make sure CBR is correctly set
+    - tracing: Build event generation tests only as modules
+    - cipso: fix total option length computation
+    - netrom: Fix a memory leak in nr_heartbeat_expiry()
+    - ipv6: prevent possible NULL deref in fib6_nh_init()
+    - ipv6: prevent possible NULL dereference in rt6_probe()
+    - xfrm6: check ip6_dst_idev() return value in xfrm6_get_saddr()
+    - netns: Make get_net_ns() handle zero refcount net
+    - qca_spi: Make interrupt remembering atomic
+    - net/sched: act_api: rely on rcu in tcf_idr_check_alloc
+    - net/sched: act_api: fix possible infinite loop in tcf_idr_check_alloc()
+    - tipc: force a dst refcount before doing decryption
+    - net/sched: act_ct: set 'net' pointer when creating new nf_flow_table
+    - sched: act_ct: add netns into the key of tcf_ct_flow_table
+    - ptp: fix integer overflow in max_vclocks_store
+    - net: stmmac: No need to calculate speed divider when offload is disabled
+    - virtio_net: checksum offloading handling fix
+    - octeontx2-pf: Add error handling to VLAN unoffload handling
+    - netfilter: ipset: Fix suspicious rcu_dereference_protected()
+    - seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6
+      behaviors
+    - bnxt_en: Restore PTP tx_avail count in case of skb_pad() error
+    - net: usb: rtl8150 fix unintiatilzed variables in rtl8150_get_link_ksettings
+    - regulator: core: Fix modpost error "regulator_get_regmap" undefined
+    - dmaengine: idxd: Fix possible Use-After-Free in irq_process_work_list
+    - dmaengine: ioat: switch from 'pci_' to 'dma_' API
+    - dmaengine: ioat: Drop redundant pci_enable_pcie_error_reporting()
+    - dmaengine: ioatdma: Fix leaking on version mismatch
+    - dmaengine: ioat: use PCI core macros for PCIe Capability
+    - dmaengine: ioatdma: Fix error path in ioat3_dma_probe()
+    - dmaengine: ioatdma: Fix kmemleak in ioat_pci_probe()
+    - dmaengine: ioatdma: Fix missing kmem_cache_destroy()
+    - regulator: bd71815: fix ramp values
+    - ACPICA: Revert "ACPICA: avoid Info: mapping multiple BARs. Your kernel is
+      fine."
+    - RDMA/mlx5: Add check for srq max_sge attribute
+    - serial: stm32: rework RX over DMA
+    - net: do not leave a dangling sk pointer, when socket creation fails
+    - btrfs: retry block group reclaim without infinite loop
+    - KVM: x86: Always sync PIR to IRR prior to scanning I/O APIC routes
+    - ALSA: hda/realtek: Limit mic boost on N14AP7
+    - drm/i915/mso: using joiner is not possible with eDP MSO
+    - drm/radeon: fix UBSAN warning in kv_dpm.c
+    - gcov: add support for GCC 14
+    - kcov: don't lose track of remote references during softirqs
+    - tcp: clear tp->retrans_stamp in tcp_rcv_fastopen_synack()
+    - i2c: ocores: set IACK bit after core is enabled
+    - dt-bindings: i2c: google,cros-ec-i2c-tunnel: correct path to i2c-controller
+      schema
+    - arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
+    - drm/amd/display: revert Exit idle optimizations before HDCP execution
+    - perf: script: add raw|disasm arguments to --insn-trace option
+    - perf script: Show also errors for --insn-trace option
+    - ARM: dts: samsung: smdkv310: fix keypad no-autorepeat
+    - ARM: dts: samsung: exynos4412-origen: fix keypad no-autorepeat
+    - ARM: dts: samsung: smdk4412: fix keypad no-autorepeat
+    - rtlwifi: rtl8192de: Style clean-ups
+    - wifi: rtlwifi: rtl8192de: Fix 5 GHz TX power
+    - pmdomain: ti-sci: Fix duplicate PD referrals
+    - bcache: fix variable length array abuse in btree_iter
+    - tracing: Add MODULE_DESCRIPTION() to preemptirq_delay_test
+    - x86/cpu/vfm: Add new macros to work with (vendor/family/model) values
+    - x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
+    - ksmbd: ignore trailing slashes in share paths
+    - drm/i915/gt: Only kick the signal worker if there's been an update
+    - drm/i915/gt: Disarm breadcrumbs if engines are already idle
+    - Revert "kheaders: substituting --sort in archive creation"
+    - kheaders: explicitly define file modes for archived headers
+    - riscv: mm: init: try best to use IS_ENABLED(CONFIG_64BIT) instead of #ifdef
+    - riscv: fix overlap of allocated page and PTR_ERR
+    - perf/core: Fix missing wakeup when waiting for context reference
+    - PCI: Add PCI_ERROR_RESPONSE and related definitions
+    - x86/amd_nb: Check for invalid SMN reads
+    - smb: client: fix deadlock in smb2_find_smb_tcon()
+    - ACPI: x86: utils: Add Picasso to the list for forcing StorageD3Enable
+    - ACPI: x86: Force StorageD3Enable on more products
+    - gve: Add RX context.
+    - gve: Clear napi->skb before dev_kfree_skb_any()
+    - Input: ili210x - fix ili251x_read_touch_data() return value
+    - pinctrl: fix deadlock in create_pinctrl() when handling -EPROBE_DEFER
+    - pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins
+    - pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins
+    - pinctrl: rockchip: use dedicated pinctrl type for RK3328
+    - pinctrl: rockchip: fix pinmux reset in rockchip_pmx_set
+    - cifs: fix typo in module parameter enable_gcm_256
+    - drm/amdgpu: fix UBSAN warning in kv_dpm.c
+    - net: mdio: add helpers to extract clause 45 regad and devad fields
+    - net: stmmac: Assign configured channel value to EXTTS event
+    - ASoC: fsl-asoc-card: set priv->pdev before using it
+    - net: dsa: microchip: fix initial port flush problem
+    - ibmvnic: Free any outstanding tx skbs during scrq reset
+    - net: phy: micrel: add Microchip KSZ 9477 to the device table
+    - xdp: Remove WARN() from __xdp_reg_mem_model()
+    - tcp: Use BPF timeout setting for SYN ACK RTO
+    - Fix race for duplicate reqsk on identical SYN
+    - sparc: fix old compat_sys_select()
+    - sparc: fix compat recv/recvfrom syscalls
+    - parisc: use correct compat recv/recvfrom syscalls
+    - tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed TFO
+    - netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data
+      registers
+    - bpf: Take return from set_memory_ro() into account with bpf_prog_lock_ro()
+    - drm/panel: ilitek-ili9881c: Fix warning with GPIO controllers that sleep
+    - vduse: validate block features only with block devices
+    - vduse: Temporarily fail if control queue feature requested
+    - x86/fpu: Fix AMD X86_BUG_FXSAVE_LEAK fixup
+    - mtd: partitions: redboot: Added conversion of operands to a larger type
+    - bpf: Add a check for struct bpf_fib_lookup size
+    - RDMA/restrack: Fix potential invalid address access
+    - net/iucv: Avoid explicit cpumask var allocation on stack
+    - net/dpaa2: Avoid explicit cpumask var allocation on stack
+    - crypto: ecdh - explicitly zeroize private_key
+    - ALSA: emux: improve patch ioctl data validation
+    - media: dvbdev: Initialize sbuf
+    - soc: ti: wkup_m3_ipc: Send NULL dummy message instead of pointer message
+    - drm/radeon/radeon_display: Decrease the size of allocated memory
+    - nvme: fixup comment for nvme RDMA Provider Type
+    - drm/panel: simple: Add missing display timing flags for KOE TX26D202VM0BWA
+    - gpio: davinci: Validate the obtained number of IRQs
+    - gpiolib: cdev: Disallow reconfiguration without direction (uAPI v1)
+    - x86: stop playing stack games in profile_pc()
+    - parisc: use generic sys_fanotify_mark implementation
+    - ocfs2: fix DIO failure due to insufficient transaction credits
+    - mmc: sdhci-pci: Convert PCIBIOS_* return codes to errnos
+    - mmc: sdhci: Do not invert write-protect twice
+    - mmc: sdhci: Do not lock spinlock around mmc_gpio_get_ro()
+    - i2c: testunit: don't erase registers after STOP
+    - i2c: testunit: discard write requests while old command is running
+    - iio: adc: ad7266: Fix variable checking bug
+    - iio: accel: fxls8962af: select IIO_BUFFER & IIO_KFIFO_BUF
+    - iio: chemical: bme680: Fix pressure value output
+    - iio: chemical: bme680: Fix calibration data variable
+    - iio: chemical: bme680: Fix overflows in compensate() functions
+    - iio: chemical: bme680: Fix sensor data read operation
+    - net: usb: ax88179_178a: improve link status logs
+    - usb: gadget: printer: SS+ support
+    - usb: gadget: printer: fix races against disable
+    - usb: musb: da8xx: fix a resource leak in probe()
+    - usb: atm: cxacru: fix endpoint checking in cxacru_bind()
+    - usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to
+      avoid deadlock
+    - serial: 8250_omap: Implementation of Errata i2310
+    - tty: mcf: MCF54418 has 10 UARTS
+    - net: can: j1939: Initialize unused data in j1939_send_one()
+    - net: can: j1939: recover socket queue on CAN bus error during BAM
+      transmission
+    - net: can: j1939: enhanced error handling for tightly received RTS messages
+      in xtp_rx_rts_session_new
+    - cpu/hotplug: Fix dynstate assignment in __cpuhp_setup_state_cpuslocked()
+    - kbuild: Install dtb files as 0644 in Makefile.dtbinst
+    - sh: rework sync_file_range ABI
+    - csky, hexagon: fix broken sys_sync_file_range
+    - hexagon: fix fadvise64_64 calling conventions
+    - drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_ld_modes
+    - drm/amdgpu: avoid using null object of framebuffer
+    - drm/i915/gt: Fix potential UAF by revoke of fence registers
+    - drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_hd_modes
+    - batman-adv: Don't accept TT entries for out-of-spec VIDs
+    - ata: ahci: Clean up sysfs file on error
+    - ata: libata-core: Fix double free on error
+    - ftruncate: pass a signed offset
+    - syscalls: fix compat_sys_io_pgetevents_time64 usage
+    - syscalls: fix sys_fanotify_mark prototype
+    - pwm: stm32: Refuse too small period requests
+    - nfs: Leave pages in the pagecache if readpage failed
+    - drivers: fix typo in firmware/efi/memmap.c
+    - efi: Correct comment on efi_memmap_alloc
+    - efi: memmap: Move manipulation routines into x86 arch tree
+    - efi: xen: Set EFI_PARAVIRT for Xen dom0 boot on all architectures
+    - efi/x86: Free EFI memory map only when installing a new one.
+    - KVM: arm64: vgic-v4: Make the doorbell request robust w.r.t preemption
+    - ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
+    - arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
+    - arm64: dts: rockchip: Add sound-dai-cells for RK3368
+    - serial: 8250_omap: Fix Errata i2310 with RX FIFO level check
+    - tracing/net_sched: NULL pointer dereference in perf_trace_qdisc_reset()
+    - Linux 5.15.162
+  * Fix L2CAP/LE/CPU/BI-02-C bluetooth certification failure  (LP: #2072858) //
+    Jammy update: v5.15.162 upstream stable release (LP: #2073765)
+    - Bluetooth: L2CAP: Fix rejecting L2CAP_CONN_PARAM_UPDATE_REQ
+  * net/sched: Fix conntrack use-after-free (LP: #2073092)
+    - net/sched: Fix UAF when resolving a clash
+  * Jammy update: v5.15.161 upstream stable release (LP: #2072617)
+    - x86/tsc: Trust initial offset in architectural TSC-adjust MSRs
+    - tty: n_gsm: fix missing receive state reset after mode switch
+    - speakup: Fix sizeof() vs ARRAY_SIZE() bug
+    - serial: 8250_bcm7271: use default_mux_rate if possible
+    - Revert "r8169: don't try to disable interrupts if NAPI is, scheduled
+      already"
+    - r8169: Fix possible ring buffer corruption on fragmented Tx packets.
+    - ring-buffer: Fix a race between readers and resize checks
+    - tools/latency-collector: Fix -Wformat-security compile warns
+    - net: smc91x: Fix m68k kernel compilation for ColdFire CPU
+    - nilfs2: fix unexpected freezing of nilfs_segctor_sync()
+    - nilfs2: fix potential hang in nilfs_detach_log_writer()
+    - fs/ntfs3: Remove max link count info display during driver init
+    - fs/ntfs3: Taking DOS names into account during link counting
+    - fs/ntfs3: Fix case when index is reused during tree transformation
+    - fs/ntfs3: Break dir enumeration if directory contents error
+    - ALSA: core: Fix NULL module pointer assignment at card init
+    - wifi: cfg80211: fix the order of arguments for trace events of the tx_rx_evt
+      class
+    - dt-bindings: rockchip: grf: Add missing type to 'pcie-phy' node
+    - net: usb: qmi_wwan: add Telit FN920C04 compositions
+    - drm/amd/display: Set color_mgmt_changed to true on unsuspend
+    - selftests: sud_test: return correct emulated syscall value on RISC-V
+    - regulator: irq_helpers: duplicate IRQ name
+    - ASoC: rt5645: Fix the electric noise due to the CBJ contacts floating
+    - ASoC: dt-bindings: rt5645: add cbj sleeve gpio property
+    - regulator: vqmmc-ipq4019: fix module autoloading
+    - ASoC: rt715: add vendor clear control register
+    - ASoC: rt715-sdca: volume step modification
+    - softirq: Fix suspicious RCU usage in __do_softirq()
+    - ASoC: da7219-aad: fix usage of device_get_named_child_node()
+    - drm/amdkfd: Flush the process wq before creating a kfd_process
+    - x86/mm: Remove broken vsyscall emulation code from the page fault code
+    - nvme: find numa distance only if controller has valid numa id
+    - epoll: be better about file lifetimes
+    - openpromfs: finish conversion to the new mount API
+    - crypto: bcm - Fix pointer arithmetic
+    - mm/slub, kunit: Use inverted data to corrupt kmem cache
+    - firmware: raspberrypi: Use correct device for DMA mappings
+    - ecryptfs: Fix buffer size for tag 66 packet
+    - nilfs2: fix out-of-range warning
+    - parisc: add missing export of __cmpxchg_u8()
+    - crypto: ccp - drop platform ifdef checks
+    - crypto: x86/nh-avx2 - add missing vzeroupper
+    - crypto: x86/sha256-avx2 - add missing vzeroupper
+    - crypto: x86/sha512-avx2 - add missing vzeroupper
+    - s390/cio: fix tracepoint subchannel type field
+    - jffs2: prevent xattr node from overflowing the eraseblock
+    - soc: mediatek: cmdq: Fix typo of CMDQ_JUMP_RELATIVE
+    - null_blk: Fix missing mutex_destroy() at module removal
+    - md: fix resync softlockup when bitmap size is less than array size
+    - wifi: ath10k: poll service ready message before failing
+    - x86/boot: Ignore relocations in .notes sections in walk_relocs() too
+    - sched/fair: Add EAS checks before updating root_domain::overutilized
+    - qed: avoid truncating work queue length
+    - bpf: Pack struct bpf_fib_lookup
+    - scsi: ufs: qcom: Perform read back after writing reset bit
+    - scsi: ufs: qcom: Perform read back after writing REG_UFS_SYS1CLK_1US
+    - scsi: ufs: ufs-qcom: Fix the Qcom register name for offset 0xD0
+    - scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5
+    - scsi: ufs: qcom: Perform read back after writing unipro mode
+    - scsi: ufs: qcom: Perform read back after writing CGC enable
+    - scsi: ufs: cdns-pltfrm: Perform read back after writing HCLKDIV
+    - scsi: ufs: core: Perform read back after disabling interrupts
+    - scsi: ufs: core: Perform read back after disabling UIC_COMMAND_COMPL
+    - irqchip/alpine-msi: Fix off-by-one in allocation error path
+    - irqchip/loongson-pch-msi: Fix off-by-one on allocation error path
+    - ACPI: disable -Wstringop-truncation
+    - gfs2: Don't forget to complete delayed withdraw
+    - gfs2: Fix "ignore unlock failures after withdraw"
+    - selftests/bpf: Fix umount cgroup2 error in test_sockmap
+    - cpufreq: Reorganize checks in cpufreq_offline()
+    - cpufreq: Split cpufreq_offline()
+    - cpufreq: Rearrange locking in cpufreq_remove_dev()
+    - cpufreq: exit() callback is optional
+    - net: export inet_lookup_reuseport and inet6_lookup_reuseport
+    - net: remove duplicate reuseport_lookup functions
+    - udp: Avoid call to compute_score on multiple sites
+    - cppc_cpufreq: Fix possible null pointer dereference
+    - scsi: libsas: Fix the failure of adding phy with zero-address to port
+    - scsi: hpsa: Fix allocation size for Scsi_Host private data
+    - x86/purgatory: Switch to the position-independent small code model
+    - thermal/drivers/tsens: Fix null pointer dereference
+    - wifi: ath10k: Fix an error code problem in
+      ath10k_dbg_sta_write_peer_debug_trigger()
+    - wifi: ath10k: populate board data for WCN3990
+    - net: dsa: mv88e6xxx: Add support for model-specific pre- and post-reset
+      handlers
+    - net: dsa: mv88e6xxx: Avoid EEPROM timeout without EEPROM on 88E6250-family
+      switches
+    - tcp: avoid premature drops in tcp_add_backlog()
+    - pwm: sti: Convert to platform remove callback returning void
+    - pwm: sti: Prepare removing pwm_chip from driver data
+    - pwm: sti: Simplify probe function using devm functions
+    - net: give more chances to rcu in netdev_wait_allrefs_any()
+    - macintosh/via-macii: Fix "BUG: sleeping function called from invalid
+      context"
+    - wifi: carl9170: add a proper sanity check for endpoints
+    - wifi: ar5523: enable proper endpoint verification
+    - sh: kprobes: Merge arch_copy_kprobe() into arch_prepare_kprobe()
+    - Revert "sh: Handle calling csum_partial with misaligned data"
+    - selftests/binderfs: use the Makefile's rules, not Make's implicit rules
+    - selftests/resctrl: fix clang build failure: use LOCAL_HDRS
+    - HID: intel-ish-hid: ipc: Add check for pci_alloc_irq_vectors
+    - scsi: bfa: Ensure the copied buf is NUL terminated
+    - scsi: qedf: Ensure the copied buf is NUL terminated
+    - scsi: qla2xxx: Fix debugfs output for fw_resource_count
+    - wifi: mwl8k: initialize cmd->addr[] properly
+    - usb: aqc111: stop lying about skb->truesize
+    - net: usb: sr9700: stop lying about skb->truesize
+    - m68k: Fix spinlock race in kernel thread creation
+    - m68k: mac: Fix reboot hang on Mac IIci
+    - net: ipv6: fix wrong start position when receive hop-by-hop fragment
+    - eth: sungem: remove .ndo_poll_controller to avoid deadlocks
+    - net: ethernet: cortina: Locking fixes
+    - af_unix: Fix data races in unix_release_sock/unix_stream_sendmsg
+    - net: usb: smsc95xx: stop lying about skb->truesize
+    - net: openvswitch: fix overwriting ct original tuple for ICMPv6
+    - ipv6: sr: add missing seg6_local_exit
+    - ipv6: sr: fix incorrect unregister order
+    - ipv6: sr: fix invalid unregister error path
+    - net/mlx5: Discard command completions in internal error
+    - s390/bpf: Emit a barrier for BPF_FETCH instructions
+    - mptcp: SO_KEEPALIVE: fix getsockopt support
+    - printk: Let no_printk() use _printk()
+    - dev_printk: Add and use dev_no_printk()
+    - drm/amd/display: Fix potential index out of bounds in color transformation
+      function
+    - ASoC: Intel: Disable route checks for Skylake boards
+    - mtd: core: Report error if first mtd_otp_size() call fails in
+      mtd_otp_nvmem_add()
+    - mtd: rawnand: hynix: fixed typo
+    - fbdev: shmobile: fix snprintf truncation
+    - ASoC: kirkwood: Fix potential NULL dereference
+    - drm/meson: vclk: fix calculation of 59.94 fractional rates
+    - drm/mediatek: Add 0 size check to mtk_drm_gem_obj
+    - powerpc/fsl-soc: hide unused const variable
+    - fbdev: sisfb: hide unused variables
+    - media: ngene: Add dvb_ca_en50221_init return value check
+    - media: radio-shark2: Avoid led_names truncations
+    - drm: bridge: cdns-mhdp8546: Fix possible null pointer dereference
+    - media: ipu3-cio2: Use temporary storage for struct device pointer
+    - media: ipu3-cio2: Request IRQ earlier
+    - media: dt-bindings: ovti,ov2680: Fix the power supply names
+    - fbdev: sh7760fb: allow modular build
+    - media: atomisp: ssh_css: Fix a null-pointer dereference in
+      load_video_binaries
+    - drm/arm/malidp: fix a possible null pointer dereference
+    - drm: vc4: Fix possible null pointer dereference
+    - ASoC: tracing: Export SND_SOC_DAPM_DIR_OUT to its value
+    - drm/bridge: lt8912b: Don't log an error when DSI host can't be found
+    - drm/bridge: lt9611: Don't log an error when DSI host can't be found
+    - drm/bridge: tc358775: Don't log an error when DSI host can't be found
+    - drm/panel: simple: Add missing Innolux G121X1-L03 format, flags, connector
+    - drm/mipi-dsi: use correct return type for the DSC functions
+    - RDMA/mlx5: Adding remote atomic access flag to updatable flags
+    - RDMA/hns: Fix return value in hns_roce_map_mr_sg
+    - RDMA/hns: Fix deadlock on SRQ async events.
+    - RDMA/hns: Fix GMV table pagesize
+    - RDMA/hns: Use complete parentheses in macros
+    - RDMA/hns: Modify the print level of CQE error
+    - clk: qcom: mmcc-msm8998: fix venus clock issue
+    - x86/insn: Fix PUSH instruction in x86 instruction decoder opcode map
+    - ext4: avoid excessive credit estimate in ext4_tmpfile()
+    - virt: acrn: Prefer array_size and struct_size over open coded arithmetic
+    - virt: acrn: stop using follow_pfn
+    - drivers/virt/acrn: fix PFNMAP PTE checks in acrn_vm_ram_map()
+    - sunrpc: removed redundant procp check
+    - ext4: simplify calculation of blkoff in ext4_mb_new_blocks_simple
+    - ext4: fix unit mismatch in ext4_mb_new_blocks_simple
+    - ext4: try all groups in ext4_mb_new_blocks_simple
+    - ext4: remove unused parameter from ext4_mb_new_blocks_simple()
+    - ext4: fix potential unnitialized variable
+    - SUNRPC: Fix gss_free_in_token_pages()
+    - selftests/kcmp: Make the test output consistent and clear
+    - selftests/kcmp: remove unused open mode
+    - RDMA/IPoIB: Fix format truncation compilation errors
+    - selftests: net: bridge: increase IGMP/MLD exclude timeout membership
+      interval
+    - net: qrtr: ns: Fix module refcnt
+    - netrom: fix possible dead-lock in nr_rt_ioctl()
+    - af_packet: do not call packet_read_pending() from tpacket_destruct_skb()
+    - sched/fair: Allow disabling sched_balance_newidle with
+      sched_relax_domain_level
+    - sched/core: Fix incorrect initialization of the 'burst' parameter in
+      cpu_max_write()
+    - greybus: lights: check return of get_channel_from_mode
+    - f2fs: Delete f2fs_copy_page() and replace with memcpy_page()
+    - f2fs: fix to wait on page writeback in __clone_blkaddrs()
+    - soundwire: cadence: fix invalid PDI offset
+    - dmaengine: idma64: Add check for dma_set_max_seg_size
+    - firmware: dmi-id: add a release callback function
+    - serial: max3100: Lock port->lock when calling uart_handle_cts_change()
+    - serial: max3100: Update uart_driver_registered on driver removal
+    - serial: max3100: Fix bitwise types
+    - greybus: arche-ctrl: move device table to its right location
+    - PCI: tegra194: Fix probe path for Endpoint mode
+    - serial: sc16is7xx: add proper sched.h include for sched_set_fifo()
+    - dt-bindings: PCI: rcar-pci-host: Add optional regulators
+    - dt-bindings: PCI: rcar-pci-host: Add missing IOMMU properties
+    - f2fs: compress: fix to relocate check condition in
+      f2fs_{release,reserve}_compress_blocks()
+    - f2fs: convert to use sbi directly
+    - f2fs: compress: fix to relocate check condition in
+      f2fs_ioc_{,de}compress_file()
+    - f2fs: do not allow partial truncation on pinned file
+    - f2fs: fix typos in comments
+    - f2fs: fix to relocate check condition in f2fs_fallocate()
+    - f2fs: fix to check pinfile flag in f2fs_move_file_range()
+    - coresight: etm4x: Fix unbalanced pm_runtime_enable()
+    - iio: pressure: dps310: support negative temperature values
+    - coresight: etm4x: Do not hardcode IOMEM access for register restore
+    - coresight: etm4x: Do not save/restore Data trace control registers
+    - coresight: no-op refactor to make INSTP0 check more idiomatic
+    - coresight: etm4x: Cleanup TRCIDR0 register accesses
+    - coresight: etm4x: Safe access for TRCQCLTR
+    - coresight: etm4x: Fix access to resource selector registers
+    - fpga: region: Use standard dev_release for class driver
+    - fpga: region: add owner module and take its refcount
+    - microblaze: Remove gcc flag for non existing early_printk.c file
+    - microblaze: Remove early printk call from cpuinfo-static.c
+    - dt-bindings: pinctrl: mediatek: mt7622: fix array properties
+    - watchdog: bd9576_wdt: switch to using devm_fwnode_gpiod_get()
+    - watchdog: bd9576: Drop "always-running" property
+    - usb: gadget: u_audio: Clear uac pointer when freed.
+    - stm class: Fix a double free in stm_register_device()
+    - ppdev: Remove usage of the deprecated ida_simple_xx() API
+    - ppdev: Add an error check in register_device
+    - extcon: max8997: select IRQ_DOMAIN instead of depending on it
+    - PCI/EDR: Align EDR_PORT_DPC_ENABLE_DSM with PCI Firmware r3.3
+    - PCI/EDR: Align EDR_PORT_LOCATE_DSM with PCI Firmware r3.3
+    - f2fs: compress: fix to cover {reserve,release}_compress_blocks() w/ cp_rwsem
+      lock
+    - f2fs: fix to release node block count in error path of f2fs_new_node_page()
+    - f2fs: compress: don't allow unaligned truncation on released compress inode
+    - serial: sh-sci: protect invalidating RXDMA on shutdown
+    - libsubcmd: Fix parse-options memory leak
+    - s390/vdso: filter out mno-pic-data-is-text-relative cflag
+    - s390/vdso64: filter out munaligned-symbols flag for vdso
+    - s390/vdso: Generate unwind information for C modules
+    - s390/vdso: Use standard stack frame layout
+    - s390/ipl: Fix incorrect initialization of len fields in nvme reipl block
+    - s390/ipl: Fix incorrect initialization of nvme dump block
+    - s390/boot: Remove alt_stfle_fac_list from decompressor
+    - Input: ims-pcu - fix printf string overflow
+    - Input: ioc3kbd - convert to platform remove callback returning void
+    - Input: ioc3kbd - add device table
+    - mmc: sdhci_am654: Add tuning algorithm for delay chain
+    - mmc: sdhci_am654: Write ITAPDLY for DDR52 timing
+    - mmc: sdhci_am654: Drop lookup for deprecated ti,otap-del-sel
+    - mmc: sdhci_am654: Add OTAP/ITAP delay enable
+    - mmc: sdhci_am654: Add ITAPDLYSEL in sdhci_j721e_4bit_set_clock
+    - mmc: sdhci_am654: Fix ITAPDLY for HS400 timing
+    - Input: pm8xxx-vibrator - correct VIB_MAX_LEVELS calculation
+    - drm/msm/dsi: Print dual-DSI-adjusted pclk instead of original mode pclk
+    - drm/msm/dpu: Always flush the slave INTF on the CTL
+    - um: Fix return value in ubd_init()
+    - um: vector: fix bpfflash parameter evaluation
+    - fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
+    - fs/ntfs3: Use variable length array instead of fixed size
+    - drm/bridge: tc358775: fix support for jeida-18 and jeida-24
+    - media: stk1160: fix bounds checking in stk1160_copy_video()
+    - scsi: qla2xxx: Replace all non-returning strlcpy() with strscpy()
+    - Input: cyapa - add missing input core locking to suspend/resume functions
+    - media: flexcop-usb: clean up endpoint sanity checks
+    - media: flexcop-usb: fix sanity check of bNumEndpoints
+    - powerpc/pseries: Add failure related checks for h_get_mpp and h_get_ppp
+    - um: Fix the -Wmissing-prototypes warning for __switch_mm
+    - media: cec: cec-adap: always cancel work in cec_transmit_msg_fh
+    - media: cec: cec-api: add locking in cec_release()
+    - media: cec: call enable_adap on s_log_addrs
+    - media: cec: abort if the current transmit was canceled
+    - media: cec: correctly pass on reply results
+    - media: cec: use call_op and check for !unregistered
+    - media: cec-adap.c: drop activate_cnt, use state info instead
+    - media: cec: core: avoid recursive cec_claim_log_addrs
+    - media: cec: core: avoid confusing "transmit timed out" message
+    - null_blk: Fix the WARNING: modpost: missing MODULE_DESCRIPTION()
+    - ASoC: mediatek: mt8192: fix register configuration for tdm
+    - regulator: bd71828: Don't overwrite runtime voltages
+    - x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when
+      UNWINDER_FRAME_POINTER=y
+    - [Config] Update CONFIG_ARCH_WANT_FRAME_POINTERS
+    - net: Always descend into dsa/ folder with CONFIG_NET_DSA enabled
+    - ipv6: sr: fix missing sk_buff release in seg6_input_core
+    - nfc: nci: Fix uninit-value in nci_rx_work
+    - ASoC: tas2552: Add TX path for capturing AUDIO-OUT data
+    - NFSv4: Fixup smatch warning for ambiguous return
+    - sunrpc: fix NFSACL RPC retry on soft mount
+    - rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
+    - af_unix: Update unix_sk(sk)->oob_skb under sk_receive_queue lock.
+    - ipv6: sr: fix memleak in seg6_hmac_init_algo
+    - tcp: Fix shift-out-of-bounds in dctcp_update_alpha().
+    - openvswitch: Set the skbuff pkt_type for proper pmtud support.
+    - arm64: asm-bug: Add .align 2 to the end of __BUG_ENTRY
+    - virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
+    - riscv: stacktrace: Make walk_stackframe cross pt_regs frame
+    - riscv: stacktrace: fixed walk_stackframe()
+    - net: fec: avoid lock evasion when reading pps_enable
+    - tls: fix missing memory barrier in tls_init
+    - nfc: nci: Fix kcov check in nci_rx_work()
+    - nfc: nci: Fix handling of zero-length payload packets in nci_rx_work()
+    - ice: Interpret .set_channels() input differently
+    - netfilter: nfnetlink_queue: acquire rcu_read_lock() in
+      instance_destroy_rcu()
+    - netfilter: nft_payload: restore vlan q-in-q match support
+    - spi: Don't mark message DMA mapped when no transfer in it is
+    - dma-mapping: benchmark: fix node id validation
+    - dma-mapping: benchmark: handle NUMA_NO_NODE correctly
+    - nvmet: fix ns enable/disable possible hang
+    - net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061
+    - net/mlx5e: Fix IPsec tunnel mode offload feature check
+    - net/mlx5e: Use rx_missed_errors instead of rx_dropped for reporting buffer
+      exhaustion
+    - dma-buf/sw-sync: don't enable IRQ from sync_print_obj()
+    - bpf: Fix potential integer overflow in resolve_btfids
+    - enic: Validate length of nl attributes in enic_set_vf_port
+    - net: usb: smsc95xx: fix changing LED_SEL bit value updated from EEPROM
+    - bpf: Allow delete from sockmap/sockhash only if update is allowed
+    - net:fec: Add fec_enet_deinit()
+    - netfilter: nft_payload: move struct nft_payload_set definition where it
+      belongs
+    - netfilter: nft_payload: rebuild vlan header when needed
+    - netfilter: nft_payload: rebuild vlan header on h_proto access
+    - netfilter: nft_payload: skbuff vlan metadata mangle support
+    - netfilter: tproxy: bail out if IP has been disabled on the device
+    - kconfig: fix comparison to constant symbols, 'm', 'n'
+    - spi: stm32: Don't warn about spurious interrupts
+    - net: ena: Add capabilities field with support for ENI stats capability
+    - net: ena: Extract recurring driver reset code into a function
+    - net: ena: Do not waste napi skb cache
+    - net: ena: Add dynamic recycling mechanism for rx buffers
+    - net: ena: Reduce lines with longer column width boundary
+    - net: ena: Fix redundant device NUMA node override
+    - ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
+    - hwmon: (shtc1) Fix property misspelling
+    - ALSA: timer: Set lower bound of start tick time
+    - KVM: x86: Don't advertise guest.MAXPHYADDR as host.MAXPHYADDR in CPUID
+    - genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
+    - net: ena: Fix DMA syncing in XDP path when SWIOTLB is on
+    - media: cec: core: add adap_nb_transmit_canceled() callback
+    - SUNRPC: Fix loop termination condition in gss_free_in_token_pages()
+    - drm: Check output polling initialized before disabling
+    - drm: Check polling initialized before enabling in
+      drm_helper_probe_single_connector_modes
+    - mmc: core: Do not force a retune before RPMB switch
+    - io_uring: fail NOP if non-zero op flags is passed in
+    - afs: Don't cross .backup mountpoint from backup volume
+    - nilfs2: fix use-after-free of timer for log writer thread
+    - mptcp: fix full TCP keep-alive support
+    - vxlan: Fix regression when dropping packets due to invalid src addresses
+    - net: dsa: sja1105: always enable the INCL_SRCPT option
+    - net: dsa: tag_sja1105: always prefer source port information from INCL_SRCPT
+    - scripts/gdb: fix SB_* constants parsing
+    - sunrpc: exclude from freezer when waiting for requests:
+    - f2fs: fix to do sanity check on i_xattr_nid in sanity_check_inode()
+    - media: lgdt3306a: Add a check against null-pointer-def
+    - drm/amdgpu: add error handle to avoid out-of-bounds
+    - ata: pata_legacy: make legacy_exit() work again
+    - thermal/drivers/qcom/lmh: Check for SCM availability at probe
+    - soc: qcom: rpmh-rsc: Enhance check for VRM in-flight request
+    - ACPI: resource: Do IRQ override on TongFang GXxHRXx and GMxHGxx
+    - arm64: tegra: Correct Tegra132 I2C alias
+    - arm64: dts: qcom: qcs404: fix bluetooth device address
+    - md/raid5: fix deadlock that raid5d() wait for itself to clear
+      MD_SB_CHANGE_PENDING
+    - wifi: rtl8xxxu: Fix the TX power of RTL8192CU, RTL8723AU
+    - wifi: rtlwifi: rtl8192de: Fix low speed with WPA3-SAE
+    - wifi: rtlwifi: rtl8192de: Fix endianness issue in RX path
+    - arm64: dts: hi3798cv200: fix the size of GICR
+    - media: mc: mark the media devnode as registered from the, start
+    - media: mxl5xx: Move xpt structures off stack
+    - media: v4l2-core: hold videodev_lock until dev reg, finishes
+    - mmc: core: Add mmc_gpiod_set_cd_config() function
+    - mmc: sdhci-acpi: Sort DMI quirks alphabetically
+    - mmc: sdhci-acpi: Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
+    - mmc: sdhci-acpi: Disable write protect detection on Toshiba WT10-A
+    - fbdev: savage: Handle err return when savagefb_check_var failed
+    - drm/amdgpu/atomfirmware: add intergrated info v2.3 table
+    - KVM: arm64: Fix AArch32 register narrowing on userspace write
+    - KVM: arm64: Allow AArch32 PSTATE.M to be restored as System mode
+    - crypto: ecdsa - Fix module auto-load on add-key
+    - crypto: ecrdsa - Fix module auto-load on add_key
+    - crypto: qat - Fix ADF_DEV_RESET_SYNC memory leak
+    - net/ipv6: Fix route deleting failure when metric equals 0
+    - net/9p: fix uninit-value in p9_client_rpc()
+    - intel_th: pci: Add Meteor Lake-S CPU support
+    - sparc64: Fix number of online CPUs
+    - watchdog: rti_wdt: Set min_hw_heartbeat_ms to accommodate a safety margin
+    - kdb: Fix buffer overflow during tab-complete
+    - kdb: Use format-strings rather than '\0' injection in kdb_read()
+    - kdb: Fix console handling when editing and tab-completing commands
+    - kdb: Merge identical case statements in kdb_read()
+    - kdb: Use format-specifiers rather than memset() for padding in kdb_read()
+    - net: fix __dst_negative_advice() race
+    - sparc: move struct termio to asm/termios.h
+    - ext4: set type of ac_groups_linear_remaining to __u32 to avoid overflow
+    - ext4: fix mb_cache_entry's e_refcnt leak in ext4_xattr_block_cache_find()
+    - s390/ap: Fix crash in AP internal function modify_bitmap()
+    - s390/cpacf: Split and rework cpacf query functions
+    - s390/cpacf: Make use of invalid opcode produce a link error
+    - i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
+    - EDAC/igen6: Convert PCIBIOS_* return codes to errnos
+    - nfs: fix undefined behavior in nfs_block_bits()
+    - NFS: Fix READ_PLUS when server doesn't support OP_READ_PLUS
+    - scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW major version > 5
+    - Linux 5.15.161
+  * Virtualbox Guru meditation on VM start caused by kernel commit in v6.9-rc4
+    (LP: #2073267)
+    - SAUCE: Revert "randomize_kstack: Improve entropy diffusion"
+  * CVE-2024-26921
+    - inet: inet_defrag: prevent sk release while still in use
+  * Jammy update: v5.15.162 upstream stable release (LP: #2073765) //
+    CVE-2024-39484
+    - mmc: davinci: Don't strip remove function when driver is builtin
+  * CVE-2024-39292
+    - um: Add winch to winch_handlers before registering winch IRQ
+  * CVE-2024-36901
+    - ipv6: prevent NULL dereference in ip6_output()
+  * CVE-2024-26830
+    - i40e: Do not allow untrusted VF to remove administratively set MAC
+  * CVE-2024-26680
+    - net: atlantic: Fix DMA mapping for PTP hwts ring
+  * CVE-2023-52760
+    - gfs2: Fix slab-use-after-free in gfs2_qd_dealloc
+  * CVE-2023-52629
+    - sh: push-switch: Reorder cleanup operations to avoid use-after-free bug
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 21 Aug 2024 13:14:37 +1000
+
+linux-xilinx-zynqmp (5.15.0-1033.37) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1033.37 -proposed tracker (LP: #2072252)
+
+  * boot failure on kv260 (LP: #2072456)
+    - Revert "dmaengine: xilinx: dpdma: Fix race condition in vsync IRQ"
+
+  [ Ubuntu: 5.15.0-118.128 ]
+
+  * jammy/linux: 5.15.0-118.128 -proposed tracker (LP: #2072255)
+  * Jammy update: v5.15.160 upstream stable release (LP: #2070292)
+    - drm/amd/display: Fix division by zero in setup_dsc_config
+    - pinctrl: core: handle radix_tree_insert() errors in
+      pinctrl_register_one_pin()
+    - nfsd: don't allow nfsd threads to be signalled.
+    - KEYS: trusted: Fix memory leak in tpm2_key_encode()
+    - Revert "selftests: mm: fix map_hugetlb failure on 64K page size systems"
+    - net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access
+    - net: bcmgenet: synchronize UMAC_CMD access
+    - netlink: annotate lockless accesses to nlk->max_recvmsg_len
+    - netlink: annotate data-races around sk->sk_err
+    - KVM: x86: Clear "has_error_code", not "error_code", for RM exception
+      injection
+    - drm/amdgpu: Fix possible NULL dereference in
+      amdgpu_ras_query_error_status_helper()
+    - binder: fix max_thread type inconsistency
+    - usb: typec: ucsi: displayport: Fix potential deadlock
+    - serial: kgdboc: Fix NMI-safety problems from keyboard reset code
+    - remoteproc: mediatek: Make sure IPI buffer fits in L2TCM
+    - KEYS: trusted: Do not use WARN when encode fails
+    - admin-guide/hw-vuln/core-scheduling: fix return type of PR_SCHED_CORE_GET
+    - docs: kernel_include.py: Cope with docutils 0.21
+    - Linux 5.15.160
+  * Jammy update: v5.15.159 upstream stable release (LP: #2070028)
+    - dmaengine: pl330: issue_pending waits until WFP state
+    - dmaengine: Revert "dmaengine: pl330: issue_pending waits until WFP state"
+    - wifi: nl80211: don't free NULL coalescing rule
+    - ksmbd: fix slab-out-of-bounds in smb2_allocate_rsp_buf
+    - ksmbd: validate request buffer size in smb2_allocate_rsp_buf()
+    - ksmbd: clear RENAME_NOREPLACE before calling vfs_rename
+    - eeprom: at24: Use dev_err_probe for nvmem register failure
+    - eeprom: at24: Probe for DDR3 thermal sensor in the SPD case
+    - eeprom: at24: fix memory corruption race condition
+    - pinctrl: pinctrl-aspeed-g6: Fix register offset for pinconf of GPIOR-T
+    - pinctrl/meson: fix typo in PDM's pin name
+    - pinctrl: core: delete incorrect free in pinctrl_enable()
+    - pinctrl: mediatek: paris: Rework mtk_pinconf_{get,set} switch/case logic
+    - pinctrl: mediatek: paris: Fix PIN_CONFIG_INPUT_SCHMITT_ENABLE readback
+    - pinctrl: mediatek: paris: Rework support for
+      PIN_CONFIG_{INPUT,OUTPUT}_ENABLE
+    - sunrpc: add a struct rpc_stats arg to rpc_create_args
+    - nfs: expose /proc/net/sunrpc/nfs in net namespaces
+    - nfs: make the rpc_stat per net namespace
+    - nfs: Handle error of rpc_proc_register() in nfs_net_init().
+    - power: rt9455: hide unused rt9455_boost_voltage_values
+    - power: supply: mt6360_charger: Fix of_match for usb-otg-vbus regulator
+    - pinctrl: devicetree: fix refcount leak in pinctrl_dt_to_map()
+    - regulator: mt6360: De-capitalize devicetree regulator subnodes
+    - bpf, kconfig: Fix DEBUG_INFO_BTF_MODULES Kconfig definition
+    - bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue
+    - bpf: Fix a verifier verbose message
+    - spi: hisi-kunpeng: Delete the dump interface of data registers in debugfs
+    - s390/mm: Fix storage key clearing for guest huge pages
+    - s390/mm: Fix clearing storage keys for huge pages
+    - xdp: Move conversion to xdp_frame out of map functions
+    - xdp: Add xdp_do_redirect_frame() for pre-computed xdp_frames
+    - xdp: use flags field to disambiguate broadcast redirect
+    - bna: ensure the copied buf is NUL terminated
+    - octeontx2-af: avoid off-by-one read from userspace
+    - nsh: Restore skb->{protocol,data,mac_header} for outer header in
+      nsh_gso_segment().
+    - net l2tp: drop flow hash on forward
+    - s390/vdso: Add CFI for RA register to asm macro vdso_func
+    - net: qede: sanitize 'rc' in qede_add_tc_flower_fltr()
+    - net: qede: use return from qede_parse_flow_attr() for flower
+    - net: qede: use return from qede_parse_flow_attr() for flow_spec
+    - net: qede: use return from qede_parse_actions()
+    - ASoC: meson: axg-fifo: use FIELD helpers
+    - ASoC: meson: axg-fifo: use threaded irq to check periods
+    - ASoC: meson: axg-card: make links nonatomic
+    - ASoC: meson: axg-tdm-interface: manage formatters in trigger
+    - ASoC: meson: cards: select SND_DYNAMIC_MINORS
+    - ALSA: hda: intel-sdw-acpi: fix usage of device_get_named_child_node()
+    - s390/cio: Ensure the copied buf is NUL terminated
+    - cxgb4: Properly lock TX queue for the selftest.
+    - net: dsa: mv88e6xxx: Fix number of databases for 88E6141 / 88E6341
+    - net: bridge: fix multicast-to-unicast with fraglist GSO
+    - net: core: reject skb_copy(_expand) for fraglist GSO skbs
+    - tipc: fix a possible memleak in tipc_buf_append
+    - s390/qeth: don't keep track of Input Queue count
+    - s390/qeth: Fix kernel panic after setting hsuid
+    - drm/panel: ili9341: Respect deferred probe
+    - drm/panel: ili9341: Use predefined error codes
+    - net: gro: add flush check in udp_gro_receive_segment
+    - clk: sunxi-ng: h6: Reparent CPUX during PLL CPUX rate change
+    - KVM: arm64: vgic-v2: Use cpuid from userspace as vcpu_id
+    - KVM: arm64: vgic-v2: Check for non-NULL vCPU in vgic_v2_parse_attr()
+    - scsi: lpfc: Move NPIV's transport unregistration to after resource clean up
+    - scsi: lpfc: Update lpfc_ramp_down_queue_handler() logic
+    - scsi: lpfc: Replace hbalock with ndlp lock in lpfc_nvme_unregister_port()
+    - gfs2: Fix invalid metadata access in punch_hole
+    - wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc
+    - wifi: cfg80211: fix rdev_dump_mpp() arguments order
+    - net: mark racy access on sk->sk_rcvbuf
+    - scsi: bnx2fc: Remove spin_lock_bh while releasing resources after upload
+    - btrfs: return accurate error code on open failure in open_fs_devices()
+    - kbuild: Disable KCSAN for autogenerated *.mod.c intermediaries
+    - ALSA: line6: Zero-initialize message buffers
+    - net: bcmgenet: Reset RBUF on first open
+    - ata: sata_gemini: Check clk_enable() result
+    - firewire: ohci: mask bus reset interrupts between ISR and bottom half
+    - tools/power turbostat: Fix added raw MSR output
+    - tools/power turbostat: Fix Bzy_MHz documentation typo
+    - btrfs: make btrfs_clear_delalloc_extent() free delalloc reserve
+    - btrfs: always clear PERTRANS metadata during commit
+    - scsi: target: Fix SELinux error when systemd-modules loads the target module
+    - blk-iocost: avoid out of bounds shift
+    - gpu: host1x: Do not setup DMA for virtual devices
+    - MIPS: scall: Save thread_info.syscall unconditionally on entry
+    - selftests: timers: Fix valid-adjtimex signed left-shift undefined behavior
+    - iommu: mtk: fix module autoloading
+    - fs/9p: only translate RWX permissions for plain 9P2000
+    - fs/9p: translate O_TRUNC into OTRUNC
+    - 9p: explicitly deny setlease attempts
+    - gpio: wcove: Use -ENOTSUPP consistently
+    - gpio: crystalcove: Use -ENOTSUPP consistently
+    - clk: Don't hold prepare_lock when calling kref_put()
+    - fs/9p: drop inodes immediately on non-.L too
+    - drm/nouveau/dp: Don't probe eDP ports twice harder
+    - net:usb:qmi_wwan: support Rolling modules
+    - bpf, sockmap: TCP data stall on recv before accept
+    - bpf, sockmap: Handle fin correctly
+    - bpf, sockmap: Convert schedule_work into delayed_work
+    - bpf, sockmap: Reschedule is now done through backlog
+    - bpf, sockmap: Improved check for empty queue
+    - qibfs: fix dentry leak
+    - xfrm: Preserve vlan tags for transport mode software GRO
+    - ARM: 9381/1: kasan: clear stale stack poison
+    - tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets
+    - tcp: Use refcount_inc_not_zero() in tcp_twsk_unique().
+    - Bluetooth: Fix use-after-free bugs caused by sco_sock_timeout
+    - Bluetooth: l2cap: fix null-ptr-deref in l2cap_chan_timeout
+    - rtnetlink: Correct nested IFLA_VF_VLAN_LIST attribute validation
+    - hwmon: (corsair-cpro) Use a separate buffer for sending commands
+    - hwmon: (corsair-cpro) Use complete_all() instead of complete() in
+      ccp_raw_event()
+    - hwmon: (corsair-cpro) Protect ccp->wait_input_report with a spinlock
+    - phonet: fix rtm_phonet_notify() skb allocation
+    - net: bridge: fix corrupted ethernet header on multicast-to-unicast
+    - ipv6: fib6_rules: avoid possible NULL dereference in fib6_rule_action()
+    - net: hns3: PF support get unicast MAC address space assigned by firmware
+    - net: hns3: using user configure after hardware reset
+    - net: hns3: add log for workqueue scheduled late
+    - net: hns3: add query vf ring and vector map relation
+    - net: hns3: refactor function hclge_mbx_handler()
+    - net: hns3: direct return when receive a unknown mailbox message
+    - net: hns3: refactor hns3 makefile to support hns3_common module
+    - net: hns3: create new cmdq hardware description structure hclge_comm_hw
+    - net: hns3: create new set of unified hclge_comm_cmd_send APIs
+    - net: hns3: refactor hclge_cmd_send with new hclge_comm_cmd_send API
+    - net: hns3: change type of numa_node_mask as nodemask_t
+    - net: hns3: use appropriate barrier function after setting a bit value
+    - net: hns3: split function hclge_init_vlan_config()
+    - net: hns3: fix port vlan filter not disabled issue
+    - drm/meson: dw-hdmi: power up phy on device init
+    - drm/meson: dw-hdmi: add bandgap setting for g12
+    - drm/connector: Add \n to message about demoting connector force-probes
+    - drm/amd/display: Atom Integrated System Info v2_2 for DCN35
+    - Revert "Revert "ACPI: CPPC: Use access_width over bit_width for system
+      memory accesses""
+    - ACPI: CPPC: Fix bit_offset shift in MASK_VAL() macro
+    - ACPI: CPPC: Fix access width used for PCC registers
+    - btrfs: fix kvcalloc() arguments order in btrfs_ioctl_send()
+    - firewire: nosy: ensure user_length is taken into account when fetching
+      packet contents
+    - Reapply "drm/qxl: simplify qxl_fence_wait"
+    - arm64: dts: qcom: Fix 'interrupt-map' parent address cells
+    - usb: typec: ucsi: Check for notifications after init
+    - usb: typec: ucsi: Fix connector check on init
+    - usb: Fix regression caused by invalid ep0 maxpacket in virtual SuperSpeed
+      device
+    - usb: ohci: Prevent missed ohci interrupts
+    - usb: gadget: composite: fix OS descriptors w_value logic
+    - usb: gadget: f_fs: Fix a race condition when processing setup packets.
+    - usb: xhci-plat: Don't include xhci.h
+    - usb: dwc3: core: Prevent phy suspend during init
+    - ALSA: hda/realtek: Fix mute led of HP Laptop 15-da3001TU
+    - btrfs: add missing mutex_unlock in btrfs_relocate_sys_chunks()
+    - mptcp: ensure snd_nxt is properly initialized on connect
+    - dt-bindings: iio: health: maxim,max30102: fix compatible check
+    - iio:imu: adis16475: Fix sync mode setting
+    - iio: accel: mxc4005: Interrupt handling fixes
+    - tipc: fix UAF in error path
+    - net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()
+    - ASoC: tegra: Fix DSPK 16-bit playback
+    - ASoC: ti: davinci-mcasp: Fix race condition during probe
+    - dyndbg: fix old BUG_ON in >control parser
+    - slimbus: qcom-ngd-ctrl: Add timeout for wait operation
+    - mei: me: add lunar lake point M DID
+    - drm/vmwgfx: Fix invalid reads in fence signaled events
+    - net: fix out-of-bounds access in ops_init
+    - hwmon: (pmbus/ucd9000) Increase delay from 250 to 500us
+    - regulator: core: fix debugfs creation regression
+    - Bluetooth: qca: add missing firmware sanity checks
+    - Bluetooth: qca: fix NVM configuration parsing
+    - Bluetooth: qca: fix firmware check error path
+    - keys: Fix overwrite of key expiration on instantiation
+    - md: fix kmemleak of rdev->serial
+    - Linux 5.15.159
+  * Freezing user space processes failed after 20.008 seconds (1 tasks refusing
+    to freeze, wq_busy=0) (LP: #2061091)
+    - ALSA: Fix deadlocks with kctl removals at disconnection
+  * CVE-2024-27017
+    - netfilter: nft_set_pipapo: constify lookup fn args where possible
+    - netfilter: nft_set_pipapo: walk over current view on netlink dump
+    - netfilter: nf_tables: missing iterator type in lookup walk
+  * CVE-2024-26952
+    - ksmbd: fix potencial out-of-bounds when buffer offset is invalid
+  * CVE-2024-26886
+    - Bluetooth: af_bluetooth: Fix deadlock
+  * CVE-2023-52752
+    - smb: client: fix use-after-free bug in cifs_debug_data_proc_show()
+  * CVE-2024-25742
+    - x86/sev: Harden #VC instruction emulation somewhat
+    - x86/sev: Check for MWAITX and MONITORX opcodes in the #VC handler
+  * CVE-2024-36016
+    - tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
+
+  [ Ubuntu: 5.15.0-116.126 ]
+
+  * jammy/linux: 5.15.0-116.126 -proposed tracker (LP: #2071603)
+  * idxd: NULL pointer dereference reading wq op_config attribute (LP: #2069081)
+    - SAUCE: dmaengine: idxd: set is_visible member of idxd_wq_attribute_group
+  * AMD GPUs fail with null pointer dereference when IOMMU enabled, leading to
+    black screen (LP: #2068738)
+    - SAUCE: Revert "drm/amdgpu: init iommu after amdkfd device init"
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 18 Jul 2024 09:24:53 -0400
+
+linux-xilinx-zynqmp (5.15.0-1032.36) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1032.36 -proposed tracker (LP: #2068392)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.zynqmp/dkms-versions -- update from kernel-versions
+      (main/2024.06.10)
+
+  [ Ubuntu: 5.15.0-115.125 ]
+
+  * jammy/linux: 5.15.0-115.125 -proposed tracker (LP: #2068396)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2024.06.10)
+  * Jammy update: v5.15.158 upstream stable release (LP: #2067974)
+    - smb: client: fix rename(2) regression against samba
+    - cifs: reinstate original behavior again for forceuid/forcegid
+    - HID: intel-ish-hid: ipc: Fix dev_err usage with uninitialized dev->devc
+    - HID: logitech-dj: allow mice to use all types of reports
+    - arm64: dts: rockchip: enable internal pull-up on Q7_USB_ID for RK3399 Puma
+    - arm64: dts: rockchip: fix alphabetical ordering RK3399 puma
+    - arm64: dts: rockchip: enable internal pull-up on PCIE_WAKE# for RK3399 Puma
+    - arm64: dts: rockchip: Remove unsupported node from the Pinebook Pro dts
+    - arm64: dts: mediatek: mt8183: Add power-domains properity to mfgcfg
+    - arm64: dts: mediatek: mt7622: add support for coherent DMA
+    - arm64: dts: mediatek: mt7622: introduce nodes for Wireless Ethernet Dispatch
+    - arm64: dts: mediatek: mt7622: fix clock controllers
+    - arm64: dts: mediatek: mt7622: fix IR nodename
+    - arm64: dts: mediatek: mt7622: fix ethernet controller "compatible"
+    - arm64: dts: mediatek: mt7622: drop "reset-names" from thermal block
+    - arm64: dts: mediatek: mt2712: fix validation errors
+    - ARC: [plat-hsdk]: Remove misplaced interrupt-cells property
+    - wifi: iwlwifi: mvm: remove old PASN station when adding a new one
+    - wifi: iwlwifi: mvm: return uid from iwl_mvm_build_scan_cmd
+    - vxlan: drop packets from invalid src-address
+    - mlxsw: core: Unregister EMAD trap using FORWARD action
+    - icmp: prevent possible NULL dereferences from icmp_build_probe()
+    - bridge/br_netlink.c: no need to return void function
+    - NFC: trf7970a: disable all regulators on removal
+    - ipv4: check for NULL idev in ip_route_use_hint()
+    - net: usb: ax88179_178a: stop lying about skb->truesize
+    - net: gtp: Fix Use-After-Free in gtp_dellink
+    - ipvs: Fix checksumming on GSO of SCTP packets
+    - net: openvswitch: Fix Use-After-Free in ovs_ct_exit
+    - mlxsw: spectrum_acl_tcam: Fix race during rehash delayed work
+    - mlxsw: spectrum_acl_tcam: Fix possible use-after-free during activity update
+    - mlxsw: spectrum_acl_tcam: Fix possible use-after-free during rehash
+    - mlxsw: spectrum_acl_tcam: Rate limit error message
+    - mlxsw: spectrum_acl_tcam: Fix memory leak during rehash
+    - mlxsw: spectrum_acl_tcam: Fix warning during rehash
+    - mlxsw: spectrum_acl_tcam: Fix incorrect list API usage
+    - mlxsw: spectrum_acl_tcam: Fix memory leak when canceling rehash work
+    - netfilter: nf_tables: honor table dormant flag from netdev release event
+      path
+    - i40e: Do not use WQ_MEM_RECLAIM flag for workqueue
+    - i40e: Report MFS in decimal base instead of hex
+    - iavf: Fix TC config comparison with existing adapter TC config
+    - net: ethernet: ti: am65-cpts: Fix PTPv1 message type on TX packets
+    - af_unix: Suppress false-positive lockdep splat for spin_lock() in
+      __unix_gc().
+    - serial: core: Provide port lock wrappers
+    - serial: mxs-auart: add spinlock around changing cts state
+    - drm-print: add drm_dbg_driver to improve namespace symmetry
+    - drm/vmwgfx: Fix crtc's atomic check conditional
+    - Revert "crypto: api - Disallow identical driver names"
+    - net/mlx5e: Fix a race in command alloc flow
+    - tracing: Show size of requested perf buffer
+    - tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker
+      together
+    - x86/cpu: Fix check for RDPKRU in __show_regs()
+    - Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old()
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0bda:0x4853
+    - Bluetooth: qca: fix NULL-deref on non-serdev suspend
+    - mmc: sdhci-msm: pervent access to suspended controller
+    - btrfs: fix information leak in btrfs_ioctl_logical_to_ino()
+    - cpu: Re-enable CPU mitigations by default for !X86 architectures
+    - [Configs] Update CPU mitigation configs
+    - arm64: dts: rockchip: enable internal pull-up for Q7_THRM# on RK3399 Puma
+    - drm/amdgpu/sdma5.2: use legacy HDP flush for SDMA2/3
+    - drm/amdgpu: Fix leak when GPU memory allocation fails
+    - irqchip/gic-v3-its: Prevent double free on error
+    - ethernet: Add helper for assigning packet type when dest address does not
+      match device address
+    - net: b44: set pause params only when interface is up
+    - stackdepot: respect __GFP_NOLOCKDEP allocation flag
+    - mtd: diskonchip: work around ubsan link failure
+    - tcp: Clean up kernel listener's reqsk in inet_twsk_purge()
+    - tcp: Fix NEW_SYN_RECV handling in inet_twsk_purge()
+    - dmaengine: owl: fix register access functions
+    - idma64: Don't try to serve interrupts when device is powered off
+    - dma: xilinx_dpdma: Fix locking
+    - dmaengine: idxd: Fix oops during rmmod on single-CPU platforms
+    - riscv: fix VMALLOC_START definition
+    - riscv: Fix TASK_SIZE on 64-bit NOMMU
+    - i2c: smbus: fix NULL function pointer dereference
+    - fbdev: fix incorrect address computation in deferred IO
+    - HID: i2c-hid: remove I2C_HID_READ_PENDING flag to prevent lock-up
+    - bounds: Use the right number of bits for power-of-two CONFIG_NR_CPUS
+    - udp: preserve the connected status if only UDP cmsg
+    - serial: core: fix kernel-doc for uart_port_unlock_irqrestore()
+    - Linux 5.15.158
+  * Jammy update: v5.15.157 upstream stable release (LP: #2067959)
+    - ksmbd: don't send oplock break if rename fails
+    - ksmbd: validate payload size in ipc response
+    - ksmbd: do not set SMB2_GLOBAL_CAP_ENCRYPTION for SMB 3.1.1
+    - btrfs: record delayed inode root in transaction
+    - SUNRPC: Fix rpcgss_context trace event acceptor field
+    - selftests/ftrace: Limit length in subsystem-enable tests
+    - bpf: Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support
+    - bpf: Generalize check_ctx_reg for reuse with other types
+    - bpf: Generally fix helper register offset check
+    - bpf: Fix out of bounds access for ringbuf helpers
+    - bpf: Fix ringbuf memory type confusion when passing to helpers
+    - kprobes: Fix possible use-after-free issue on kprobe registration
+    - Revert "tracing/trigger: Fix to return error if failed to alloc snapshot"
+    - netfilter: nf_tables: Fix potential data-race in __nft_expr_type_get()
+    - netfilter: nf_tables: Fix potential data-race in __nft_obj_type_get()
+    - netfilter: br_netfilter: skip conntrack input hook for promisc packets
+    - netfilter: nf_flow_table: count pending offload workqueue tasks
+    - [Config] update configs to enable new NF_FLOW_TABLE_PROCFS
+    - netfilter: flowtable: validate pppoe header
+    - netfilter: flowtable: incorrect pppoe tuple
+    - af_unix: Call manage_oob() for every skb in unix_stream_read_generic().
+    - af_unix: Don't peek OOB data without MSG_OOB.
+    - tun: limit printing rate when illegal packet received by tun dev
+    - net: dsa: mt7530: fix mirroring frames received on local port
+    - net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
+    - RDMA/rxe: Fix the problem "mutex_destroy missing"
+    - RDMA/cm: Print the old state when cm_destroy_id gets timeout
+    - RDMA/mlx5: Fix port number for counter query in multi-port configuration
+    - s390/qdio: handle deferred cc1
+    - s390/cio: fix race condition during online processing
+    - drm: nv04: Fix out of bounds access
+    - drm/panel: visionox-rm69299: don't unregister DSI device
+    - clk: Remove prepare_lock hold assertion in __clk_release()
+    - clk: Mark 'all_lists' as const
+    - clk: remove extra empty line
+    - clk: Print an info line before disabling unused clocks
+    - clk: Initialize struct clk_core kref earlier
+    - clk: Get runtime PM before walking tree during disable_unused
+    - x86/bugs: Fix BHI retpoline check
+    - x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
+    - thunderbolt: Avoid notify PM core about runtime PM resume
+    - thunderbolt: Fix wake configurations after device unplug
+    - comedi: vmk80xx: fix incomplete endpoint checking
+    - serial/pmac_zilog: Remove flawed mitigation for rx irq flood
+    - USB: serial: option: add Fibocom FM135-GL variants
+    - USB: serial: option: add support for Fibocom FM650/FG650
+    - USB: serial: option: add Lonsung U8300/U9300 product
+    - USB: serial: option: support Quectel EM060K sub-models
+    - USB: serial: option: add Rolling RW101-GL and RW135-GL support
+    - USB: serial: option: add Telit FN920C04 rmnet compositions
+    - usb: dwc2: host: Fix dereference issue in DDMA completion flow.
+    - usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport
+      error
+    - mei: me: disable RPL-S on SPS and IGN firmwares
+    - speakup: Avoid crash on very long word
+    - fs: sysfs: Fix reference leak in sysfs_break_active_protection()
+    - KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
+    - KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
+    - arm64: hibernate: Fix level3 translation fault in swsusp_save()
+    - init/main.c: Fix potential static_command_line memory overflow
+    - drm/vmwgfx: Sort primary plane formats by order of preference
+    - nouveau: fix instmem race condition around ptr stores
+    - nilfs2: fix OOB in nilfs_set_de_type
+    - net: dsa: mt7530: set all CPU ports in MT7531_CPU_PMAP
+    - net: dsa: introduce preferred_default_local_cpu_port and use on MT7530
+    - net: dsa: mt7530: fix improper frames on all 25MHz and 40MHz XTAL MT7530
+    - net: dsa: mt7530: fix enabling EEE on MT7531 switch on all boards
+    - Linux 5.15.157
+  * [SRU][22.04.4]: megaraid_sas: Critical Bug Fixes (LP: #2046722)
+    - scsi: megaraid_sas: Log message when controller reset is requested but not
+      issued
+    - scsi: megaraid_sas: Driver version update to 07.727.03.00-rc1
+  * Jammy update: v5.15.156 upstream stable release (LP: #2065857)
+    - batman-adv: Avoid infinite loop trying to resize local TT
+    - ring-buffer: Only update pages_touched when a new page is touched
+    - Bluetooth: Fix memory leak in hci_req_sync_complete()
+    - media: cec: core: remove length check of Timer Status
+    - arm64: dts: imx8-ss-conn: fix usdhc wrong lpcg clock order
+    - Revert "drm/qxl: simplify qxl_fence_wait"
+    - nouveau: fix function cast warning
+    - scsi: qla2xxx: Fix off by one in qla_edif_app_getstats()
+    - net: openvswitch: fix unwanted error log on timeout policy probing
+    - u64_stats: Disable preemption on 32bit UP+SMP PREEMPT_RT during updates.
+    - xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING
+    - geneve: fix header validation in geneve[6]_xmit_skb
+    - af_unix: Clear stale u->oob_skb.
+    - octeontx2-af: Fix NIX SQ mode and BP config
+    - ipv6: fib: hide unused 'pn' variable
+    - ipv4/route: avoid unused-but-set-variable warning
+    - ipv6: fix race condition between ipv6_get_ifaddr and ipv6_del_addr
+    - netfilter: complete validation of user input
+    - net/mlx5: Properly link new fs rules into the tree
+    - net: sparx5: fix wrong config being used when reconfiguring PCS
+    - net: dsa: mt7530: trap link-local frames regardless of ST Port State
+    - af_unix: Do not use atomic ops for unix_sk(sk)->inflight.
+    - af_unix: Fix garbage collector racing against connect()
+    - net: ena: Fix potential sign extension issue
+    - net: ena: Wrong missing IO completions check order
+    - net: ena: Fix incorrect descriptor free behavior
+    - tracing: hide unused ftrace_event_id_fops
+    - iommu/vt-d: Allocate local memory for page request queue
+    - btrfs: qgroup: correctly model root qgroup rsv in convert
+    - drm/client: Fully protect modes[] with dev->mode_config.mutex
+    - vhost: Add smp_rmb() in vhost_vq_avail_empty()
+    - perf/x86: Fix out of range data
+    - x86/cpu: Actually turn off mitigations by default for
+      SPECULATION_MITIGATIONS=n
+    - selftests: timers: Fix abs() warning in posix_timers test
+    - x86/apic: Force native_apic_mem_read() to use the MOV instruction
+    - irqflags: Explicitly ignore lockdep_hrtimer_exit() argument
+    - x86/bugs: Fix return type of spectre_bhi_state()
+    - x86/bugs: Fix BHI documentation
+    - x86/bugs: Cache the value of MSR_IA32_ARCH_CAPABILITIES
+    - x86/bugs: Rename various 'ia32_cap' variables to 'x86_arch_cap_msr'
+    - x86/bugs: Fix BHI handling of RRSBA
+    - x86/bugs: Clarify that syscall hardening isn't a BHI mitigation
+    - x86/bugs: Remove CONFIG_BHI_MITIGATION_AUTO and spectre_bhi=auto
+    - [Config] updateconfigs to remove obsolete SPECTRE_BHI_AUTO
+    - x86/bugs: Replace CONFIG_SPECTRE_BHI_{ON,OFF} with
+      CONFIG_MITIGATION_SPECTRE_BHI
+    - [Config] updateconfigs to enable new MITIGATION_SPECTRE_BHI
+    - drm/i915/cdclk: Fix CDCLK programming order when pipes are active
+    - Linux 5.15.156
+  * Jammy update: v5.15.155 upstream stable release (LP: #2065805)
+    - amdkfd: use calloc instead of kzalloc to avoid integer overflow
+    - net: dsa: fix panic when DSA master device unbinds on shutdown
+    - wifi: ath9k: fix LNA selection in ath_ant_try_scan()
+    - VMCI: Fix memcpy() run-time warning in dg_dispatch_as_host()
+    - panic: Flush kernel log buffer at the end
+    - cpuidle: Avoid potential overflow in integer multiplication
+    - arm64: dts: rockchip: fix rk3328 hdmi ports node
+    - arm64: dts: rockchip: fix rk3399 hdmi ports node
+    - ionic: set adminq irq affinity
+    - pstore/zone: Add a null pointer check to the psz_kmsg_read
+    - tools/power x86_energy_perf_policy: Fix file leak in get_pkg_num()
+    - net: pcs: xpcs: Return EINVAL in the internal methods
+    - wifi: ath11k: decrease MHI channel buffer length to 8KB
+    - btrfs: handle chunk tree lookup error in btrfs_relocate_sys_chunks()
+    - btrfs: export: handle invalid inode or root reference in btrfs_get_parent()
+    - btrfs: send: handle path ref underflow in header iterate_inode_ref()
+    - net/smc: reduce rtnl pressure in smc_pnet_create_pnetids_list()
+    - Bluetooth: btintel: Fix null ptr deref in btintel_read_version
+    - Input: synaptics-rmi4 - fail probing if memory allocation for "phys" fails
+    - pinctrl: renesas: checker: Limit cfg reg enum checks to provided IDs
+    - sysv: don't call sb_bread() with pointers_lock held
+    - scsi: lpfc: Fix possible memory leak in lpfc_rcv_padisc()
+    - isofs: handle CDs with bad root inode but good Joliet root directory
+    - media: sta2x11: fix irq handler cast
+    - ALSA: firewire-lib: handle quirk to calculate payload quadlets as data block
+      counter
+    - ext4: add a hint for block bitmap corrupt state in mb_groups
+    - ext4: forbid commit inconsistent quota data when errors=remount-ro
+    - drm/amd/display: Fix nanosec stat overflow
+    - SUNRPC: increase size of rpc_wait_queue.qlen from unsigned short to unsigned
+      int
+    - Revert "ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default"
+    - libperf evlist: Avoid out-of-bounds access
+    - block: prevent division by zero in blk_rq_stat_sum()
+    - RDMA/cm: add timeout to cm_destroy_id wait
+    - Input: allocate keycode for Display refresh rate toggle
+    - platform/x86: touchscreen_dmi: Add an extra entry for a variant of the Chuwi
+      Vi8 tablet
+    - ktest: force $buildonly = 1 for 'make_warnings_file' test type
+    - ring-buffer: use READ_ONCE() to read cpu_buffer->commit_page in concurrent
+      environment
+    - tools: iio: replace seekdir() in iio_generic_buffer
+    - usb: typec: tcpci: add generic tcpci fallback compatible
+    - usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
+    - ASoC: soc-core.c: Skip dummy codec when adding platforms
+    - fbdev: viafb: fix typo in hw_bitblt_1 and hw_bitblt_2
+    - drivers/nvme: Add quirks for device 126f:2262
+    - fbmon: prevent division by zero in fb_videomode_from_videomode()
+    - netfilter: nf_tables: release batch on table validation from abort path
+    - netfilter: nf_tables: release mutex after nft_gc_seq_end from abort path
+    - netfilter: nf_tables: discard table flag update with pending basechain
+      deletion
+    - tty: n_gsm: require CAP_NET_ADMIN to attach N_GSM0710 ldisc
+    - gcc-plugins/stackleak: Ignore .noinstr.text and .entry.text
+    - gcc-plugins/stackleak: Avoid .head.text section
+    - virtio: reenable config if freezing device failed
+    - x86/mm/pat: fix VM_PAT handling in COW mappings
+    - randomize_kstack: Improve entropy diffusion
+    - platform/x86: intel-vbtn: Update tablet mode switch at end of probe
+    - Bluetooth: btintel: Fixe build regression
+    - VMCI: Fix possible memcpy() run-time warning in
+      vmci_datagram_invoke_guest_handler()
+    - Linux 5.15.155
+  * Jammy update: v5.15.154 upstream stable release (LP: #2065435)
+    - Documentation/hw-vuln: Update spectre doc
+    - x86/cpu: Support AMD Automatic IBRS
+    - media: staging: ipu3-imgu: Set fields before media_entity_pads_init()
+    - clk: qcom: gcc-sdm845: Add soft dependency on rpmhpd
+    - smack: Set SMACK64TRANSMUTE only for dirs in smack_inode_setxattr()
+    - smack: Handle SMACK64TRANSMUTE in smack_inode_setsecurity()
+    - arm: dts: marvell: Fix maxium->maxim typo in brownstone dts
+    - drm/vmwgfx: Fix possible null pointer derefence with invalid contexts
+    - pci_iounmap(): Fix MMIO mapping leak
+    - KVM: Always flush async #PF workqueue when vCPU is being destroyed
+    - sparc64: NMI watchdog: fix return value of __setup handler
+    - sparc: vDSO: fix return value of __setup handler
+    - crypto: qat - fix double free during reset
+    - crypto: qat - resolve race condition during AER recovery
+    - selftests/mqueue: Set timeout to 180 seconds
+    - ext4: correct best extent lstart adjustment logic
+    - block: Clear zone limits for a non-zoned stacked queue
+    - kasan: test: add memcpy test that avoids out-of-bounds write
+    - kasan/test: avoid gcc warning for intentional overflow
+    - bounds: support non-power-of-two CONFIG_NR_CPUS
+    - fat: fix uninitialized field in nostale filehandles
+    - ubifs: Set page uptodate in the correct place
+    - ubi: Check for too small LEB size in VTBL code
+    - ubi: correct the calculation of fastmap size
+    - mtd: rawnand: meson: fix scrambling mode value in command macro
+    - parisc: Avoid clobbering the C/B bits in the PSW with tophys and tovirt
+      macros
+    - parisc: Fix ip_fast_csum
+    - parisc: Fix csum_ipv6_magic on 32-bit systems
+    - parisc: Fix csum_ipv6_magic on 64-bit systems
+    - parisc: Strip upper 32 bit of sum in csum_ipv6_magic for 64-bit builds
+    - PM: suspend: Set mem_sleep_current during kernel command line setup
+    - clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
+    - clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
+    - clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
+    - clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
+    - usb: xhci: Add error handling in xhci_map_urb_for_dma
+    - powerpc/fsl: Fix mfpmr build errors with newer binutils
+    - USB: serial: ftdi_sio: add support for GMC Z216C Adapter IR-USB
+    - USB: serial: add device ID for VeriFone adapter
+    - USB: serial: cp210x: add ID for MGP Instruments PDS100
+    - USB: serial: option: add MeiG Smart SLM320 product
+    - USB: serial: cp210x: add pid/vid for TDK NC0110013M and MM0110113M
+    - PM: sleep: wakeirq: fix wake irq warning in system suspend
+    - mmc: tmio: avoid concurrent runs of mmc_request_done()
+    - fuse: fix root lookup with nonzero generation
+    - fuse: don't unhash root
+    - usb: typec: ucsi: Clean up UCSI_CABLE_PROP macros
+    - printk/console: Split out code that enables default console
+    - serial: Lock console when calling into driver before registration
+    - btrfs: fix off-by-one chunk length calculation at contains_pending_extent()
+    - PCI: Drop pci_device_remove() test of pci_dev->driver
+    - PCI/PM: Drain runtime-idle callbacks before driver removal
+    - PCI: Work around Intel I210 ROM BAR overlap defect
+    - PCI/ASPM: Make Intel DG2 L1 acceptable latency unlimited
+    - PCI/DPC: Quirk PIO log size for certain Intel Root Ports
+    - PCI/DPC: Quirk PIO log size for Intel Raptor Lake Root Ports
+    - dm-raid: fix lockdep waring in "pers->hot_add_disk"
+    - mac802154: fix llsec key resources release in mac802154_llsec_key_del
+    - swap: comments get_swap_device() with usage rule
+    - mm: swap: fix race between free_swap_and_cache() and swapoff()
+    - mmc: core: Fix switch on gp3 partition
+    - drm/etnaviv: Restore some id values
+    - landlock: Warn once if a Landlock action is requested while disabled
+    - hwmon: (amc6821) add of_match table
+    - ext4: fix corruption during on-line resize
+    - nvmem: meson-efuse: fix function pointer type mismatch
+    - slimbus: core: Remove usage of the deprecated ida_simple_xx() API
+    - phy: tegra: xusb: Add API to retrieve the port number of phy
+    - usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
+    - speakup: Fix 8bit characters from direct synth
+    - PCI/AER: Block runtime suspend when handling errors
+    - nfs: fix UAF in direct writes
+    - kbuild: Move -Wenum-{compare-conditional,enum-conversion} into W=1
+    - PCI: dwc: endpoint: Fix advertised resizable BAR size
+    - vfio/platform: Disable virqfds on cleanup
+    - ksmbd: retrieve number of blocks using vfs_getattr in
+      set_file_allocation_info
+    - ring-buffer: Fix waking up ring buffer readers
+    - ring-buffer: Do not set shortest_full when full target is hit
+    - ring-buffer: Fix resetting of shortest_full
+    - ring-buffer: Fix full_waiters_pending in poll
+    - ring-buffer: Use wait_event_interruptible() in ring_buffer_wait()
+    - soc: fsl: qbman: Always disable interrupts when taking cgr_lock
+    - soc: fsl: qbman: Add helper for sanity checking cgr ops
+    - soc: fsl: qbman: Add CGR update function
+    - soc: fsl: qbman: Use raw spinlock for cgr_lock
+    - s390/zcrypt: fix reference counting on zcrypt card objects
+    - drm/panel: do not return negative error codes from drm_panel_get_modes()
+    - drm/exynos: do not return negative values from .get_modes()
+    - drm/imx/ipuv3: do not return negative values from .get_modes()
+    - drm/vc4: hdmi: do not return negative values from .get_modes()
+    - memtest: use {READ,WRITE}_ONCE in memory scanning
+    - nilfs2: fix failure to detect DAT corruption in btree and direct mappings
+    - nilfs2: prevent kernel bug at submit_bh_wbc()
+    - cpufreq: dt: always allocate zeroed cpumask
+    - x86/CPU/AMD: Update the Zenbleed microcode revisions
+    - NFSD: Fix nfsd_clid_class use of __string_len() macro
+    - net: hns3: tracing: fix hclgevf trace event strings
+    - wireguard: netlink: check for dangling peer via is_dead instead of empty
+      list
+    - wireguard: netlink: access device through ctx instead of peer
+    - ahci: asm1064: correct count of reported ports
+    - ahci: asm1064: asm1166: don't limit reported ports
+    - drm/amdgpu: amdgpu_ttm_gart_bind set gtt bound flag
+    - drm/amd/display: Return the correct HDCP error code
+    - drm/amd/display: Fix noise issue on HDMI AV mute
+    - dm snapshot: fix lockup in dm_exception_table_exit
+    - x86/pm: Work around false positive kmemleak report in msr_build_context()
+    - net: ravb: Add R-Car Gen4 support
+    - cpufreq: brcmstb-avs-cpufreq: fix up "add check for cpufreq_cpu_get's return
+      value"
+    - netfilter: nf_tables: reject constant set with timeout
+    - Drivers: hv: vmbus: Calculate ring buffer size for more efficient use of
+      memory
+    - xfrm: Avoid clang fortify warning in copy_to_user_tmpl()
+    - KVM: SVM: Flush pages under kvm->lock to fix UAF in
+      svm_register_enc_region()
+    - tracing: Use .flush() call to wake up readers
+    - drm/i915: Check before removing mm notifier
+    - USB: usb-storage: Prevent divide-by-0 error in isd200_ata_command
+    - usb: gadget: ncm: Fix handling of zero block length packets
+    - usb: port: Don't try to peer unused USB ports based on location
+    - tty: serial: fsl_lpuart: avoid idle preamble pending if CTS is enabled
+    - mei: me: add arrow lake point S DID
+    - mei: me: add arrow lake point H DID
+    - vt: fix unicode buffer corruption when deleting characters
+    - fs/aio: Check IOCB_AIO_RW before the struct aio_kiocb conversion
+    - tee: optee: Fix kernel panic caused by incorrect error handling
+    - i2c: i801: Avoid potential double call to gpiod_remove_lookup_table
+    - xen/events: close evtchn after mapping cleanup
+    - clocksource/drivers/arm_global_timer: Fix maximum prescaler value
+    - entry: Respect changes to system call number by trace_sys_enter()
+    - minmax: add umin(a, b) and umax(a, b)
+    - swiotlb: Fix alignment checks when both allocation and DMA masks are present
+    - dma-mapping: add dma_opt_mapping_size()
+    - dma-iommu: add iommu_dma_opt_mapping_size()
+    - iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
+    - printk: Update @console_may_schedule in console_trylock_spinning()
+    - tty: serial: imx: Fix broken RS485
+    - x86/asm: Add _ASM_RIP() macro for x86-64 (%rip) suffix
+    - x86/bugs: Add asm helpers for executing VERW
+    - x86/entry_64: Add VERW just before userspace transition
+    - x86/entry_32: Add VERW just before userspace transition
+    - x86/bugs: Use ALTERNATIVE() instead of mds_user_clear static key
+    - KVM/VMX: Use BT+JNC, i.e. EFLAGS.CF to select VMRESUME vs. VMLAUNCH
+    - KVM/VMX: Move VERW closer to VMentry for MDS mitigation
+    - x86/mmio: Disable KVM mitigation when X86_FEATURE_CLEAR_CPU_BUF is set
+    - Documentation/hw-vuln: Add documentation for RFDS
+    - x86/rfds: Mitigate Register File Data Sampling (RFDS)
+    - [Config] updateconfigs for MITIGATION_RFDS
+    - KVM/x86: Export RFDS_NO and RFDS_CLEAR to guests
+    - arch: Introduce CONFIG_FUNCTION_ALIGNMENT
+    - [Config] updateconfigs for FUNCTION_ALIGNMENT
+    - x86/asm: Differentiate between code and function alignment
+    - x86/alternatives: Introduce int3_emulate_jcc()
+    - x86/alternatives: Teach text_poke_bp() to patch Jcc.d32 instructions
+    - x86/static_call: Add support for Jcc tail-calls
+    - fsnotify: pass data_type to fsnotify_name()
+    - fsnotify: pass dentry instead of inode data
+    - fsnotify: clarify contract for create event hooks
+    - fsnotify: Don't insert unmergeable events in hashtable
+    - fanotify: Fold event size calculation to its own function
+    - fanotify: Split fsid check from other fid mode checks
+    - inotify: Don't force FS_IN_IGNORED
+    - fsnotify: Add helper to detect overflow_event
+    - fsnotify: Add wrapper around fsnotify_add_event
+    - fsnotify: Retrieve super block from the data field
+    - fsnotify: Protect fsnotify_handle_inode_event from no-inode events
+    - fsnotify: Pass group argument to free_event
+    - fanotify: Support null inode event in fanotify_dfid_inode
+    - fanotify: Allow file handle encoding for unhashed events
+    - fanotify: Encode empty file handle when no inode is provided
+    - fanotify: Require fid_mode for any non-fd event
+    - fsnotify: Support FS_ERROR event type
+    - fanotify: Reserve UAPI bits for FAN_FS_ERROR
+    - fanotify: Pre-allocate pool of error events
+    - fanotify: Support enqueueing of error events
+    - fanotify: Support merging of error events
+    - fanotify: Wrap object_fh inline space in a creator macro
+    - fanotify: Add helpers to decide whether to report FID/DFID
+    - fanotify: WARN_ON against too large file handles
+    - fanotify: Report fid info for file related file system errors
+    - fanotify: Emit generic error info for error event
+    - fanotify: Allow users to request FAN_FS_ERROR events
+    - ext4: Send notifications on error
+    - docs: Document the FAN_FS_ERROR event
+    - NFS: Remove unnecessary TRACE_DEFINE_ENUM()s
+    - SUNRPC: Tracepoints should display tk_pid and cl_clid as a fixed-size field
+    - NFS: Move generic FS show macros to global header
+    - NFS: Move NFS protocol display macros to global header
+    - NFSD: Optimize DRC bucket pruning
+    - NFSD: move filehandle format declarations out of "uapi".
+    - NFSD: drop support for ancient filehandles
+    - NFSD: simplify struct nfsfh
+    - NFSD: Initialize pointer ni with NULL and not plain integer 0
+    - SUNRPC: Replace the "__be32 *p" parameter to .pc_decode
+    - SUNRPC: Change return value type of .pc_decode
+    - NFSD: Save location of NFSv4 COMPOUND status
+    - SUNRPC: Replace the "__be32 *p" parameter to .pc_encode
+    - SUNRPC: Change return value type of .pc_encode
+    - nfsd: update create verifier comment
+    - NFSD:fix boolreturn.cocci warning
+    - nfsd4: remove obselete comment
+    - ext4: fix error code saved on super block during file system abort
+    - fsnotify: clarify object type argument
+    - fsnotify: separate mark iterator type from object type enum
+    - fanotify: introduce group flag FAN_REPORT_TARGET_FID
+    - fsnotify: generate FS_RENAME event with rich information
+    - fanotify: use macros to get the offset to fanotify_info buffer
+    - fanotify: use helpers to parcel fanotify_info buffer
+    - fanotify: support secondary dir fh and name in fanotify_info
+    - fanotify: record old and new parent and name in FAN_RENAME event
+    - fanotify: record either old name new name or both for FAN_RENAME
+    - fanotify: report old and/or new parent+name in FAN_RENAME event
+    - fanotify: wire up FAN_RENAME event
+    - exit: Implement kthread_exit
+    - exit: Rename module_put_and_exit to module_put_and_kthread_exit
+    - NFSD: handle errors better in write_ports_addfd()
+    - SUNRPC: change svc_get() to return the svc.
+    - SUNRPC/NFSD: clean up get/put functions.
+    - SUNRPC: stop using ->sv_nrthreads as a refcount
+    - nfsd: make nfsd_stats.th_cnt atomic_t
+    - SUNRPC: use sv_lock to protect updates to sv_nrthreads.
+    - NFSD: narrow nfsd_mutex protection in nfsd thread
+    - NFSD: Make it possible to use svc_set_num_threads_sync
+    - SUNRPC: discard svo_setup and rename svc_set_num_threads_sync()
+    - NFSD: simplify locking for network notifier.
+    - lockd: introduce nlmsvc_serv
+    - lockd: simplify management of network status notifiers
+    - lockd: move lockd_start_svc() call into lockd_create_svc()
+    - lockd: move svc_exit_thread() into the thread
+    - lockd: introduce lockd_put()
+    - lockd: rename lockd_create_svc() to lockd_get()
+    - SUNRPC: move the pool_map definitions (back) into svc.c
+    - SUNRPC: always treat sv_nrpools==1 as "not pooled"
+    - lockd: use svc_set_num_threads() for thread start and stop
+    - NFS: switch the callback service back to non-pooled.
+    - NFSD: Remove be32_to_cpu() from DRC hash function
+    - NFSD: Fix inconsistent indenting
+    - NFSD: simplify per-net file cache management
+    - NFSD: Combine XDR error tracepoints
+    - nfsd: improve stateid access bitmask documentation
+    - NFSD: De-duplicate nfsd4_decode_bitmap4()
+    - nfs: block notification on fs with its own ->lock
+    - nfsd4: add refcount for nfsd4_blocked_lock
+    - nfsd: map EBADF
+    - nfsd: Add errno mapping for EREMOTEIO
+    - nfsd: Retry once in nfsd_open on an -EOPENSTALE return
+    - NFSD: Clean up nfsd_vfs_write()
+    - NFSD: De-duplicate net_generic(SVC_NET(rqstp), nfsd_net_id)
+    - nfsd: Add a tracepoint for errors in nfsd4_clone_file_range()
+    - NFSD: Write verifier might go backwards
+    - NFSD: Clean up the nfsd_net::nfssvc_boot field
+    - NFSD: Rename boot verifier functions
+    - NFSD: Trace boot verifier resets
+    - NFSD: Move fill_pre_wcc() and fill_post_wcc()
+    - fsnotify: invalidate dcache before IN_DELETE event
+    - NFSD: Deprecate NFS_OFFSET_MAX
+    - nfsd: Add support for the birth time attribute
+    - orDate: Thu Sep 30 19:19:57 2021 -0400
+    - NFSD: Skip extra computation for RC_NOCACHE case
+    - NFSD: Streamline the rare "found" case
+    - NFSD: Remove NFSD_PROC_ARGS_* macros
+    - SUNRPC: Remove the .svo_enqueue_xprt method
+    - SUNRPC: Merge svc_do_enqueue_xprt() into svc_enqueue_xprt()
+    - SUNRPC: Remove svo_shutdown method
+    - SUNRPC: Rename svc_create_xprt()
+    - SUNRPC: Rename svc_close_xprt()
+    - SUNRPC: Remove svc_shutdown_net()
+    - NFSD: Remove svc_serv_ops::svo_module
+    - NFSD: Move svc_serv_ops::svo_function into struct svc_serv
+    - NFSD: Remove CONFIG_NFSD_V3
+    - [Config] updateconfigs for NFSD_V3
+    - NFSD: Clean up _lm_ operation names
+    - nfsd: fix using the correct variable for sizeof()
+    - fsnotify: fix merge with parent's ignored mask
+    - fsnotify: optimize FS_MODIFY events with no ignored masks
+    - fsnotify: remove redundant parameter judgment
+    - nfsd: Fix a write performance regression
+    - nfsd: Clean up nfsd_file_put()
+    - fanotify: do not allow setting dirent events in mask of non-dir
+    - fs/lock: documentation cleanup. Replace inode->i_lock with flc_lock.
+    - inotify: move control flags from mask to mark flags
+    - fsnotify: pass flags argument to fsnotify_alloc_group()
+    - fsnotify: make allow_dups a property of the group
+    - fsnotify: create helpers for group mark_mutex lock
+    - inotify: use fsnotify group lock helpers
+    - nfsd: use fsnotify group lock helpers
+    - dnotify: use fsnotify group lock helpers
+    - fsnotify: allow adding an inode mark without pinning inode
+    - fanotify: create helper fanotify_mark_user_flags()
+    - fanotify: factor out helper fanotify_mark_update_flags()
+    - fanotify: implement "evictable" inode marks
+    - fanotify: use fsnotify group lock helpers
+    - fanotify: enable "evictable" inode marks
+    - fsnotify: introduce mark type iterator
+    - fsnotify: consistent behavior for parent not watching children
+    - fanotify: fix incorrect fmode_t casts
+    - NFSD: Clean up nfsd_splice_actor()
+    - NFSD: add courteous server support for thread with only delegation
+    - NFSD: add support for share reservation conflict to courteous server
+    - NFSD: move create/destroy of laundry_wq to init_nfsd and exit_nfsd
+    - fs/lock: add helper locks_owner_has_blockers to check for blockers
+    - fs/lock: add 2 callbacks to lock_manager_operations to resolve conflict
+    - NFSD: add support for lock conflict to courteous server
+    - NFSD: Show state of courtesy client in client info
+    - NFSD: Clean up nfsd3_proc_create()
+    - NFSD: Avoid calling fh_drop_write() twice in do_nfsd_create()
+    - NFSD: Refactor nfsd_create_setattr()
+    - NFSD: Refactor NFSv3 CREATE
+    - NFSD: Refactor NFSv4 OPEN(CREATE)
+    - NFSD: Remove do_nfsd_create()
+    - NFSD: Clean up nfsd_open_verified()
+    - NFSD: Instantiate a struct file when creating a regular NFSv4 file
+    - NFSD: Remove dprintk call sites from tail of nfsd4_open()
+    - NFSD: Fix whitespace
+    - NFSD: Move documenting comment for nfsd4_process_open2()
+    - NFSD: Trace filecache opens
+    - SUNRPC: Use RMW bitops in single-threaded hot paths
+    - nfsd: Unregister the cld notifier when laundry_wq create failed
+    - nfsd: Fix null-ptr-deref in nfsd_fill_super()
+    - NFSD: Modernize nfsd4_release_lockowner()
+    - NFSD: Add documenting comment for nfsd4_release_lockowner()
+    - NFSD: nfsd_file_put() can sleep
+    - NFSD: Fix potential use-after-free in nfsd_file_put()
+    - NFS: restore module put when manager exits.
+    - fanotify: refine the validation checks on non-dir inode mask
+    - NFSD: Decode NFSv4 birth time attribute
+    - fs: inotify: Fix typo in inotify comment
+    - fanotify: prepare for setting event flags in ignore mask
+    - fanotify: cleanups for fanotify_mark() input validations
+    - fanotify: introduce FAN_MARK_IGNORE
+    - fsnotify: Fix comment typo
+    - NLM: Defend against file_lock changes after vfs_test_lock()
+    - NFSD: Instrument fh_verify()
+    - NFSD: Fix space and spelling mistake
+    - nfsd: remove redundant assignment to variable len
+    - NFSD: Demote a WARN to a pr_warn()
+    - NFSD: Report filecache LRU size
+    - NFSD: Report count of calls to nfsd_file_acquire()
+    - NFSD: Report count of freed filecache items
+    - NFSD: Report average age of filecache items
+    - NFSD: Add nfsd_file_lru_dispose_list() helper
+    - NFSD: Refactor nfsd_file_gc()
+    - NFSD: Refactor nfsd_file_lru_scan()
+    - NFSD: Report the number of items evicted by the LRU walk
+    - NFSD: Record number of flush calls
+    - NFSD: Zero counters when the filecache is re-initialized
+    - NFSD: Hook up the filecache stat file
+    - NFSD: WARN when freeing an item still linked via nf_lru
+    - NFSD: Trace filecache LRU activity
+    - NFSD: Leave open files out of the filecache LRU
+    - NFSD: Fix the filecache LRU shrinker
+    - NFSD: Never call nfsd_file_gc() in foreground paths
+    - NFSD: No longer record nf_hashval in the trace log
+    - NFSD: Remove lockdep assertion from unhash_and_release_locked()
+    - NFSD: nfsd_file_unhash can compute hashval from nf->nf_inode
+    - NFSD: Refactor __nfsd_file_close_inode()
+    - NFSD: nfsd_file_hash_remove can compute hashval
+    - NFSD: Remove nfsd_file::nf_hashval
+    - NFSD: Replace the "init once" mechanism
+    - NFSD: Set up an rhashtable for the filecache
+    - NFSD: Convert the filecache to use rhashtable
+    - NFSD: Clean up unused code after rhashtable conversion
+    - NFSD: Separate tracepoints for acquire and create
+    - NFSD: Move nfsd_file_trace_alloc() tracepoint
+    - NFSD: NFSv4 CLOSE should release an nfsd_file immediately
+    - NFSD: Ensure nf_inode is never dereferenced
+    - NFSD: refactoring v4 specific code to a helper in nfs4state.c
+    - NFSD: keep track of the number of v4 clients in the system
+    - NFSD: limit the number of v4 clients to 1024 per 1GB of system memory
+    - nfsd: silence extraneous printk on nfsd.ko insertion
+    - NFSD: Optimize nfsd4_encode_operation()
+    - NFSD: Optimize nfsd4_encode_fattr()
+    - NFSD: Clean up SPLICE_OK in nfsd4_encode_read()
+    - NFSD: Add an nfsd4_read::rd_eof field
+    - NFSD: Optimize nfsd4_encode_readv()
+    - NFSD: Simplify starting_len
+    - NFSD: Use xdr_pad_size()
+    - NFSD: Clean up nfsd4_encode_readlink()
+    - NFSD: Fix strncpy() fortify warning
+    - NFSD: nfserrno(-ENOMEM) is nfserr_jukebox
+    - NFSD: Shrink size of struct nfsd4_copy_notify
+    - NFSD: Shrink size of struct nfsd4_copy
+    - NFSD: Reorder the fields in struct nfsd4_op
+    - NFSD: Make nfs4_put_copy() static
+    - NFSD: Replace boolean fields in struct nfsd4_copy
+    - NFSD: Refactor nfsd4_cleanup_inter_ssc() (1/2)
+    - NFSD: Refactor nfsd4_cleanup_inter_ssc() (2/2)
+    - NFSD: Refactor nfsd4_do_copy()
+    - NFSD: Remove kmalloc from nfsd4_do_async_copy()
+    - NFSD: Add nfsd4_send_cb_offload()
+    - NFSD: Move copy offload callback arguments into a separate structure
+    - NFSD: drop fh argument from alloc_init_deleg
+    - NFSD: verify the opened dentry after setting a delegation
+    - NFSD: introduce struct nfsd_attrs
+    - NFSD: set attributes when creating symlinks
+    - NFSD: add security label to struct nfsd_attrs
+    - NFSD: add posix ACLs to struct nfsd_attrs
+    - NFSD: change nfsd_create()/nfsd_symlink() to unlock directory before
+      returning.
+    - NFSD: always drop directory lock in nfsd_unlink()
+    - NFSD: only call fh_unlock() once in nfsd_link()
+    - NFSD: reduce locking in nfsd_lookup()
+    - NFSD: use explicit lock/unlock for directory ops
+    - NFSD: use (un)lock_inode instead of fh_(un)lock for file operations
+    - NFSD: discard fh_locked flag and fh_lock/fh_unlock
+    - NFSD: fix regression with setting ACLs.
+    - nfsd_splice_actor(): handle compound pages
+    - NFSD: move from strlcpy with unused retval to strscpy
+    - lockd: move from strlcpy with unused retval to strscpy
+    - NFSD enforce filehandle check for source file in COPY
+    - NFSD: remove redundant variable status
+    - nfsd: Avoid some useless tests
+    - nfsd: Propagate some error code returned by memdup_user()
+    - NFSD: Increase NFSD_MAX_OPS_PER_COMPOUND
+    - NFSD: drop fname and flen args from nfsd_create_locked()
+    - nfsd: clean up mounted_on_fileid handling
+    - nfsd: remove nfsd4_prepare_cb_recall() declaration
+    - NFSD: Replace dprintk() call site in fh_verify()
+    - NFSD: Trace NFSv4 COMPOUND tags
+    - NFSD: Add tracepoints to report NFSv4 callback completions
+    - NFSD: Add a mechanism to wait for a DELEGRETURN
+    - NFSD: Refactor nfsd_setattr()
+    - NFSD: Make nfsd4_setattr() wait before returning NFS4ERR_DELAY
+    - NFSD: Make nfsd4_rename() wait before returning NFS4ERR_DELAY
+    - NFSD: Make nfsd4_remove() wait before returning NFS4ERR_DELAY
+    - NFSD: keep track of the number of courtesy clients in the system
+    - NFSD: add shrinker to reap courtesy clients on low memory condition
+    - SUNRPC: Parametrize how much of argsize should be zeroed
+    - NFSD: Reduce amount of struct nfsd4_compoundargs that needs clearing
+    - NFSD: Refactor common code out of dirlist helpers
+    - NFSD: Use xdr_inline_decode() to decode NFSv3 symlinks
+    - NFSD: Clean up WRITE arg decoders
+    - NFSD: Clean up nfs4svc_encode_compoundres()
+    - NFSD: Remove unused nfsd4_compoundargs::cachetype field
+    - NFSD: Pack struct nfsd4_compoundres
+    - nfsd: use DEFINE_PROC_SHOW_ATTRIBUTE to define nfsd_proc_ops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define export_features_fops and
+      supported_enctypes_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define client_info_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define nfsd_reply_cache_stats_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define nfsd_file_cache_stats_fops
+    - NFSD: Rename the fields in copy_stateid_t
+    - nfsd: only fill out return pointer on success in nfsd4_lookup_stateid
+    - nfsd: fix comments about spinlock handling with delegations
+    - nfsd: make nfsd4_run_cb a bool return function
+    - nfsd: extra checks when freeing delegation stateids
+    - fs/notify: constify path
+    - fsnotify: remove unused declaration
+    - fanotify: Remove obsoleted fanotify_event_has_path()
+    - nfsd: fix nfsd_file_unhash_and_dispose
+    - nfsd: rework hashtable handling in nfsd_do_file_acquire
+    - NFSD: unregister shrinker when nfsd_init_net() fails
+    - nfsd: ensure we always call fh_verify_error tracepoint
+    - nfsd: fix net-namespace logic in __nfsd_file_cache_purge
+    - nfsd: fix use-after-free in nfsd_file_do_acquire tracepoint
+    - nfsd: put the export reference in nfsd4_verify_deleg_dentry
+    - NFSD: Fix trace_nfsd_fh_verify_err() crasher
+    - NFSD: Fix reads with a non-zero offset that don't end on a page boundary
+    - lockd: use locks_inode_context helper
+    - nfsd: use locks_inode_context helper
+    - NFSD: Simplify READ_PLUS
+    - NFSD: Remove redundant assignment to variable host_err
+    - NFSD: Finish converting the NFSv3 GETACL result encoder
+    - nfsd: ignore requests to disable unsupported versions
+    - nfsd: move nfserrno() to vfs.c
+    - nfsd: allow disabling NFSv2 at compile time
+    - [Config] updateconfigs for NFSD_V2
+    - exportfs: use pr_debug for unreachable debug statements
+    - NFSD: Pass the target nfsd_file to nfsd_commit()
+    - NFSD: Revert "NFSD: NFSv4 CLOSE should release an nfsd_file immediately"
+    - NFSD: Add an NFSD_FILE_GC flag to enable nfsd_file garbage collection
+    - NFSD: Flesh out a documenting comment for filecache.c
+    - NFSD: Clean up nfs4_preprocess_stateid_op() call sites
+    - NFSD: Trace stateids returned via DELEGRETURN
+    - NFSD: Trace delegation revocations
+    - NFSD: Use const pointers as parameters to fh_ helpers
+    - NFSD: Update file_hashtbl() helpers
+    - NFSD: Clean up nfsd4_init_file()
+    - NFSD: Add a nfsd4_file_hash_remove() helper
+    - NFSD: Clean up find_or_add_file()
+    - NFSD: Refactor find_file()
+    - NFSD: Use rhashtable for managing nfs4_file objects
+    - NFSD: Fix licensing header in filecache.c
+    - nfsd: remove the pages_flushed statistic from filecache
+    - nfsd: reorganize filecache.c
+    - filelock: add a new locks_inode_context accessor function
+    - nfsd: fix up the filecache laundrette scheduling
+    - NFSD: Add an nfsd_file_fsync tracepoint
+    - nfsd: return error if nfs4_setacl fails
+    - NFSD: Use struct_size() helper in alloc_session()
+    - lockd: set missing fl_flags field when retrieving args
+    - lockd: ensure we use the correct file descriptor when unlocking
+    - lockd: fix file selection in nlmsvc_cancel_blocked
+    - trace: Relocate event helper files
+    - NFSD: refactoring courtesy_client_reaper to a generic low memory shrinker
+    - NFSD: add support for sending CB_RECALL_ANY
+    - NFSD: add delegation reaper to react to low memory condition
+    - NFSD: add CB_RECALL_ANY tracepoints
+    - NFSD: Use only RQ_DROPME to signal the need to drop a reply
+    - NFSD: Avoid clashing function prototypes
+    - nfsd: rework refcounting in filecache
+    - nfsd: fix handling of cached open files in nfsd4_open codepath
+    - Revert "SUNRPC: Use RMW bitops in single-threaded hot paths"
+    - NFSD: Use set_bit(RQ_DROPME)
+    - NFSD: register/unregister of nfsd-client shrinker at nfsd startup/shutdown
+      time
+    - NFSD: replace delayed_work with work_struct for nfsd_client_shrinker
+    - nfsd: don't free files unconditionally in __nfsd_file_cache_purge
+    - nfsd: don't destroy global nfs4_file table in per-net shutdown
+    - NFSD: enhance inter-server copy cleanup
+    - nfsd: allow nfsd_file_get to sanely handle a NULL pointer
+    - nfsd: clean up potential nfsd_file refcount leaks in COPY codepath
+    - NFSD: fix leaked reference count of nfsd4_ssc_umount_item
+    - nfsd: don't hand out delegation on setuid files being opened for write
+    - NFSD: fix problems with cleanup on errors in nfsd4_copy
+    - nfsd: fix courtesy client with deny mode handling in nfs4_upgrade_open
+    - nfsd: don't fsync nfsd_files on last close
+    - NFSD: copy the whole verifier in nfsd_copy_write_verifier
+    - NFSD: Protect against filesystem freezing
+    - nfsd: don't replace page in rq_pages if it's a continuation of last page
+    - nfsd: call op_release, even when op_func returns an error
+    - nfsd: don't open-code clear_and_wake_up_bit
+    - nfsd: NFSD_FILE_KEY_INODE only needs to find GC'ed entries
+    - nfsd: simplify test_bit return in NFSD_FILE_KEY_FULL comparator
+    - nfsd: don't kill nfsd_files because of lease break error
+    - nfsd: add some comments to nfsd_file_do_acquire
+    - nfsd: don't take/put an extra reference when putting a file
+    - nfsd: update comment over __nfsd_file_cache_purge
+    - nfsd: allow reaping files still under writeback
+    - NFSD: Convert filecache to rhltable
+    - nfsd: simplify the delayed disposal list code
+    - NFSD: Fix problem of COMMIT and NFS4ERR_DELAY in infinite loop
+    - nfsd: make a copy of struct iattr before calling notify_change
+    - nfsd: fix double fget() bug in __write_ports_addfd()
+    - lockd: drop inappropriate svc_get() from locked_get()
+    - NFSD: Add an nfsd4_encode_nfstime4() helper
+    - nfsd: Fix creation time serialization order
+    - nfsd: Simplify code around svc_exit_thread() call in nfsd()
+    - nfsd: separate nfsd_last_thread() from nfsd_put()
+    - Documentation: Add missing documentation for EXPORT_OP flags
+    - NFSD: fix possible oops when nfsd/pool_stats is closed.
+    - nfsd: call nfsd_last_thread() before final nfsd_put()
+    - nfsd: drop the nfsd_put helper
+    - nfsd: fix RELEASE_LOCKOWNER
+    - nfsd: don't take fi_lock in nfsd_break_deleg_cb()
+    - nfsd: don't call locks_release_private() twice concurrently
+    - nfsd: Fix a regression in nfsd_setattr()
+    - perf/core: Fix reentry problem in perf_output_read_group()
+    - efivarfs: Request at most 512 bytes for variable names
+    - powerpc: xor_vmx: Add '-mhard-float' to CFLAGS
+    - selftests: mptcp: diag: return KSFT_FAIL not test_cnt
+    - vfio/pci: Disable auto-enable of exclusive INTx IRQ
+    - vfio/pci: Lock external INTx masking ops
+    - vfio: Introduce interface to flush virqfd inject workqueue
+    - vfio/pci: Create persistent INTx handler
+    - vfio/platform: Create persistent IRQ handlers
+    - vfio/fsl-mc: Block calling interrupt handler without trigger
+    - serial: sc16is7xx: convert from _raw_ to _noinc_ regmap functions for FIFO
+    - mm/migrate: set swap entry values of THP tail pages properly.
+    - init: open /initrd.image with O_LARGEFILE
+    - btrfs: zoned: use zone aware sb location for scrub
+    - wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes
+    - exec: Fix NOMMU linux_binprm::exec in transfer_args_to_stack()
+    - hexagon: vmlinux.lds.S: handle attributes section
+    - mmc: core: Initialize mmc_blk_ioc_data
+    - mmc: core: Avoid negative index with array access
+    - net: ll_temac: platform_get_resource replaced by wrong function
+    - drm/i915/gt: Reset queue_priority_hint on parking
+    - drm/amdgpu: Use drm_mode_copy()
+    - drm/amd/display: Preserve original aspect ratio in create stream
+    - ALSA: sh: aica: reorder cleanup operations to avoid UAF bugs
+    - scsi: core: Fix unremoved procfs host directory regression
+    - staging: vc04_services: changen strncpy() to strscpy_pad()
+    - staging: vc04_services: fix information leak in create_component()
+    - USB: core: Add hub_get() and hub_put() routines
+    - usb: dwc2: host: Fix remote wakeup from hibernation
+    - usb: dwc2: host: Fix hibernation flow
+    - usb: dwc2: host: Fix ISOC flow in DDMA mode
+    - usb: dwc2: gadget: Fix exiting from clock gating
+    - usb: dwc2: gadget: LPM flow fix
+    - usb: udc: remove warning when queue disabled ep
+    - usb: typec: ucsi: Ack unsupported commands
+    - usb: typec: ucsi: Clear UCSI_CCI_RESET_COMPLETE before reset
+    - scsi: qla2xxx: Prevent command send on chip reset
+    - scsi: qla2xxx: Fix N2N stuck connection
+    - scsi: qla2xxx: Split FCE|EFT trace control
+    - scsi: qla2xxx: NVME|FCP prefer flag not being honored
+    - scsi: qla2xxx: Fix command flush on cable pull
+    - scsi: qla2xxx: Fix double free of fcport
+    - scsi: qla2xxx: Change debug message during driver unload
+    - scsi: qla2xxx: Delay I/O Abort on PCI error
+    - x86/cpu: Enable STIBP on AMD if Automatic IBRS is enabled
+    - PCI/DPC: Quirk PIO log size for Intel Ice Lake Root Ports
+    - scsi: lpfc: Correct size for wqe for memset()
+    - USB: core: Fix deadlock in usb_deauthorize_interface()
+    - scsi: usb: Call scsi_done() directly
+    - scsi: usb: Stop using the SCSI pointer
+    - USB: UAS: return ENODEV when submit urbs fail with device not attached
+    - nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet
+    - mlxbf_gige: stop PHY during open() error paths
+    - iwlwifi: mvm: rfi: use kmemdup() to replace kzalloc + memcpy
+    - wifi: iwlwifi: mvm: rfi: fix potential response leaks
+    - ixgbe: avoid sleeping allocation in ixgbe_ipsec_vf_add_sa()
+    - s390/qeth: handle deferred cc1
+    - tcp: properly terminate timers for kernel sockets
+    - ACPICA: debugger: check status of acpi_evaluate_object() in
+      acpi_db_walk_for_fields()
+    - mlxbf_gige: call request_irq() after NAPI initialized
+    - bpf: Protect against int overflow for stack access size
+    - Octeontx2-af: fix pause frame configuration in GMP mode
+    - dm integrity: fix out-of-range warning
+    - r8169: fix issue caused by buggy BIOS on certain boards with RTL8168d
+    - x86/cpufeatures: Add new word for scattered features
+    - x86/cpufeatures: Add CPUID_LNX_5 to track recently added Linux-defined word
+    - arm64: dts: qcom: sc7180-trogdor: mark bluetooth address as broken
+    - Bluetooth: hci_event: set the conn encrypted before conn establishes
+    - Bluetooth: Fix TOCTOU in HCI debugfs implementation
+    - xen-netfront: Add missing skb_mark_for_recycle
+    - net/rds: fix possible cp null dereference
+    - locking/rwsem: Disable preemption while trying for rwsem lock
+    - io_uring: ensure '0' is returned on file registration success
+    - Revert "x86/mm/ident_map: Use gbpages only where full GB page should be
+      mapped."
+    - mm, vmscan: prevent infinite loop for costly GFP_NOIO | __GFP_RETRY_MAYFAIL
+      allocations
+    - thermal: devfreq_cooling: Fix perf state when calculate dfc res_util
+    - KVM: x86: Bail to userspace if emulation of atomic user access faults
+    - KVM: x86: Mark target gfn of emulated atomic instruction as dirty
+    - netfilter: nf_tables: reject new basechain after table flag update
+    - netfilter: nf_tables: flush pending destroy work before exit_net release
+    - netfilter: nf_tables: Fix potential data-race in __nft_flowtable_type_get()
+    - netfilter: validate user input for expected length
+    - vboxsf: Avoid an spurious warning if load_nls_xxx() fails
+    - bpf, sockmap: Prevent lock inversion deadlock in map delete elem
+    - net/sched: act_skbmod: prevent kernel-infoleak
+    - net: stmmac: fix rx queue priority assignment
+    - selftests: net: gro fwd: update vxlan GRO test expectations
+    - erspan: make sure erspan_base_hdr is present in skb->head
+    - selftests: reuseaddr_conflict: add missing new line at the end of the output
+    - ipv6: Fix infinite recursion in fib6_dump_done().
+    - mlxbf_gige: stop interface during shutdown
+    - udp: do not accept non-tunnel GSO skbs landing in a tunnel
+    - udp: do not transition UDP GRO fraglist partial checksums to unnecessary
+    - udp: prevent local UDP tunnel packets from being GROed
+    - octeontx2-af: Fix issue with loading coalesced KPU profiles
+    - octeontx2-pf: check negative error code in otx2_open()
+    - i40e: fix i40e_count_filters() to count only active/new filters
+    - i40e: fix vf may be used uninitialized in this function warning
+    - scsi: qla2xxx: Update manufacturer details
+    - scsi: qla2xxx: Update manufacturer detail
+    - Revert "usb: phy: generic: Get the vbus supply"
+    - i40e: Store the irq number in i40e_q_vector
+    - i40e: Remove _t suffix from enum type names
+    - i40e: Enforce software interrupt during busy-poll exit
+    - net: usb: asix: suspend embedded PHY if external is used
+    - drivers: net: convert to boolean for the mac_managed_pm flag
+    - net: fec: Set mac_managed_pm during probe
+    - net: ravb: Always process TX descriptor ring
+    - ASoC: rt5682-sdw: fix locking sequence
+    - ASoC: rt711-sdca: fix locking sequence
+    - ASoC: rt711-sdw: fix locking sequence
+    - ASoC: ops: Fix wraparound for mask in snd_soc_get_volsw
+    - ata: sata_sx4: fix pdc20621_get_from_dimm() on 64-bit
+    - scsi: mylex: Fix sysfs buffer lengths
+    - ata: sata_mv: Fix PCI device ID table declaration compilation warning
+    - nfsd: hold a lighter-weight client reference over CB_RECALL_ANY
+    - HID: uhid: Use READ_ONCE()/WRITE_ONCE() for ->running
+    - openrisc: Fix pagewalk usage in arch_dma_{clear, set}_uncached
+    - fs/pipe: Fix lockdep false-positive in watchqueue pipe_write()
+    - ALSA: hda/realtek: Update Panasonic CF-SZ6 quirk to support headset with
+      microphone
+    - driver core: Introduce device_link_wait_removal()
+    - of: dynamic: Synchronize of_changeset_destroy() with the devlink removals
+    - x86/mce: Make sure to grab mce_sysfs_mutex in set_bank()
+    - s390/entry: align system call table on 8 bytes
+    - riscv: Fix spurious errors from __get/put_kernel_nofault
+    - riscv: process: Fix kernel gp leakage
+    - x86/bugs: Fix the SRSO mitigation on Zen3/4
+    - x86/retpoline: Do the necessary fixup to the Zen3/4 srso return thunk for
+      !SRSO
+    - mptcp: don't account accept() of non-MPC client as fallback to TCP
+    - mm/secretmem: fix GUP-fast succeeding on secretmem folios
+    - gro: fix ownership transfer
+    - nvme: fix miss command type check
+    - x86: set SPECTRE_BHI_ON as default
+    - Linux 5.15.154
+  * CVE-2024-23307
+    - md/raid5: fix atomicity violation in raid5_cache_count
+  * CVE-2024-26828
+    - cifs: fix underflow in parse_server_interfaces()
+  * CVE-2024-24861
+    - media: xc4000: Fix atomicity violation in xc4000_get_frequency
+  * CVE-2024-26642
+    - netfilter: nf_tables: disallow anonymous set with timeout flag
+  * CVE-2024-26926
+    - binder: check offset alignment in binder_get_object()
+  * CVE-2024-26922
+    - drm/amdgpu: validate the parameters of bo mapping operations more clearly
+  * CVE-2023-6039
+    - timers: Silently ignore timers with a NULL function
+  * CVE-2024-26924
+    - netfilter: nft_set_pipapo: do not free live element
+  * CVE-2024-26643
+    - netfilter: nf_tables: mark set as dead when unbinding anonymous set with
+      timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Tue, 18 Jun 2024 09:09:18 +1000
+
+linux-xilinx-zynqmp (5.15.0-1031.35) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1031.35 -proposed tracker (LP: #2068238)
+
+  [ Ubuntu: 5.15.0-113.123 ]
+
+  * jammy/linux: 5.15.0-113.123 -proposed tracker (LP: #2068242)
+  * CVE-2024-26924
+    - netfilter: nft_set_pipapo: do not free live element
+  * CVE-2024-26643
+    - netfilter: nf_tables: mark set as dead when unbinding anonymous set with
+      timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 14 Jun 2024 09:20:22 +1000
+
+linux-xilinx-zynqmp (5.15.0-1030.34) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1030.34 -proposed tracker (LP: #2063760)
+
+  * Revert "crypto: api - Disallow identical driver names" (LP: #2064724)
+    - Revert "crypto: api - Disallow identical driver names"
+
+  [ Ubuntu: 5.15.0-112.122 ]
+
+  * jammy/linux: 5.15.0-112.122 -proposed tracker (LP: #2065898)
+  * CVE-2024-21823
+    - dmanegine: idxd: reformat opcap output to match bitmap_parse() input
+    - dmaengine: idxd: add WQ operation cap restriction support
+    - dmaengine: idxd: add knob for enqcmds retries
+    - VFIO: Add the SPR_DSA and SPR_IAX devices to the denylist
+    - dmaengine: idxd: add a new security check to deal with a hardware erratum
+    - dmaengine: idxd: add a write() method for applications to submit work
+
+  [ Ubuntu: 5.15.0-111.121 ]
+
+  * jammy/linux: 5.15.0-111.121 -proposed tracker (LP: #2063763)
+  * RTL8852BE fw security fail then lost WIFI function during suspend/resume
+    cycle (LP: #2063096)
+    - wifi: rtw89: download firmware with five times retry
+  * Mount CIFS fails with Permission denied (LP: #2061986)
+    - cifs: fix ntlmssp auth when there is no key exchange
+  * USB stick can't be detected (LP: #2040948)
+    - usb: Disable USB3 LPM at shutdown
+  * Jammy update: v5.15.153 upstream stable release (LP: #2063290)
+    - io_uring/unix: drop usage of io_uring socket
+    - io_uring: drop any code related to SCM_RIGHTS
+    - selftests: tls: use exact comparison in recv_partial
+    - ASoC: rt5645: Make LattePanda board DMI match more precise
+    - x86/xen: Add some null pointer checking to smp.c
+    - MIPS: Clear Cause.BD in instruction_pointer_set
+    - HID: multitouch: Add required quirk for Synaptics 0xcddc device
+    - gen_compile_commands: fix invalid escape sequence warning
+    - RDMA/mlx5: Fix fortify source warning while accessing Eth segment
+    - RDMA/mlx5: Relax DEVX access upon modify commands
+    - riscv: dts: sifive: add missing #interrupt-cells to pmic
+    - x86/mm: Move is_vsyscall_vaddr() into asm/vsyscall.h
+    - x86/mm: Disallow vsyscall page read for copy_from_kernel_nofault()
+    - net/iucv: fix the allocation size of iucv_path_table array
+    - parisc/ftrace: add missing CONFIG_DYNAMIC_FTRACE check
+    - block: sed-opal: handle empty atoms when parsing response
+    - dm-verity, dm-crypt: align "struct bvec_iter" correctly
+    - scsi: mpt3sas: Prevent sending diag_reset when the controller is ready
+    - ALSA: hda/realtek - ALC285 reduce pop noise from Headphone port
+    - drm/amdgpu: Enable gpu reset for S3 abort cases on Raven series
+    - Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security
+    - firewire: core: use long bus reset on gap count error
+    - ASoC: Intel: bytcr_rt5640: Add an extra entry for the Chuwi Vi8 tablet
+    - Input: gpio_keys_polled - suppress deferred probe error for gpio
+    - ASoC: wm8962: Enable oscillator if selecting WM8962_FLL_OSC
+    - ASoC: wm8962: Enable both SPKOUTR_ENA and SPKOUTL_ENA in mono mode
+    - ASoC: wm8962: Fix up incorrect error message in wm8962_set_fll
+    - do_sys_name_to_handle(): use kzalloc() to fix kernel-infoleak
+    - s390/dasd: put block allocation in separate function
+    - s390/dasd: add query PPRC function
+    - s390/dasd: add copy pair setup
+    - s390/dasd: add autoquiesce feature
+    - s390/dasd: Use dev_*() for device log messages
+    - s390/dasd: fix double module refcount decrement
+    - fs/select: rework stack allocation hack for clang
+    - md: Don't clear MD_CLOSING when the raid is about to stop
+    - lib/cmdline: Fix an invalid format specifier in an assertion msg
+    - time: test: Fix incorrect format specifier
+    - rtc: test: Fix invalid format specifier.
+    - aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts
+    - timekeeping: Fix cross-timestamp interpolation on counter wrap
+    - timekeeping: Fix cross-timestamp interpolation corner case decision
+    - timekeeping: Fix cross-timestamp interpolation for non-x86
+    - sched/fair: Take the scheduling domain into account in select_idle_core()
+    - wifi: ath10k: fix NULL pointer dereference in
+      ath10k_wmi_tlv_op_pull_mgmt_tx_compl_ev()
+    - wifi: b43: Stop/wake correct queue in DMA Tx path when QoS is disabled
+    - wifi: b43: Stop/wake correct queue in PIO Tx path when QoS is disabled
+    - wifi: b43: Stop correct queue in DMA worker when QoS is disabled
+    - wifi: b43: Disable QoS for bcm4331
+    - wifi: wilc1000: fix declarations ordering
+    - wifi: wilc1000: fix RCU usage in connect path
+    - wifi: rtl8xxxu: add cancel_work_sync() for c2hcmd_work
+    - wifi: wilc1000: fix multi-vif management when deleting a vif
+    - wifi: mwifiex: debugfs: Drop unnecessary error check for
+      debugfs_create_dir()
+    - cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
+    - cpufreq: Explicitly include correct DT includes
+    - cpufreq: mediatek-hw: Wait for CPU supplies before probing
+    - sock_diag: annotate data-races around sock_diag_handlers[family]
+    - inet_diag: annotate data-races around inet_diag_table[]
+    - bpftool: Silence build warning about calloc()
+    - af_unix: Annotate data-race of gc_in_progress in wait_for_unix_gc().
+    - cpufreq: mediatek-hw: Don't error out if supply is not found
+    - arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM
+    - arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL
+      board
+    - arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD
+      card
+    - arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO
+      voltage
+    - arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL
+      board
+    - wifi: ath9k: delay all of ath9k_wmi_event_tasklet() until init is complete
+    - wifi: iwlwifi: mvm: report beacon protection failures
+    - wifi: iwlwifi: dbg-tlv: ensure NUL termination
+    - wifi: iwlwifi: fix EWRD table validity check
+    - arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
+    - pwm: atmel-hlcdc: Convert to platform remove callback returning void
+    - pwm: atmel-hlcdc: Use consistent variable naming
+    - pwm: atmel-hlcdc: Fix clock imbalance related to suspend support
+    - net: blackhole_dev: fix build warning for ethh set but not used
+    - wifi: libertas: fix some memleaks in lbs_allocate_cmd_buffer()
+    - pwm: sti: Implement .apply() callback
+    - pwm: sti: Fix capture for st,pwm-num-chan < st,capture-num-chan
+    - wifi: iwlwifi: mvm: don't set replay counters to 0xff
+    - s390/vdso: drop '-fPIC' from LDFLAGS
+    - ipv6: mcast: remove one synchronize_net() barrier in ipv6_mc_down()
+    - arm64: dts: mt8183: kukui: Add Type C node
+    - arm64: dts: mt8183: kukui: Split out keyboard node and describe detachables
+    - arm64: dts: mt8183: Move CrosEC base detection node to kukui-based DTs
+    - arm64: dts: mediatek: mt7622: add missing "device_type" to memory nodes
+    - bpf: Mark bpf_spin_{lock,unlock}() helpers with notrace correctly
+    - wireless: Remove redundant 'flush_workqueue()' calls
+    - wifi: wilc1000: prevent use-after-free on vif when cleaning up all
+      interfaces
+    - ACPI: processor_idle: Fix memory leak in acpi_processor_power_exit()
+    - bus: tegra-aconnect: Update dependency to ARCH_TEGRA
+    - [Config]: update CONFIG_TEGRA_ACONNECT
+    - iommu/amd: Mark interrupt as managed
+    - wifi: brcmsmac: avoid function pointer casts
+    - net: ena: Remove ena_select_queue
+    - ARM: dts: arm: realview: Fix development chip ROM compatible value
+    - arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
+    - arm64: dts: renesas: r8a779a0: Correct avb[01] reg sizes
+    - ARM: dts: imx6dl-yapp4: Move phy reset into switch node
+    - ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address
+    - ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node
+    - arm64: dts: marvell: reorder crypto interrupts on Armada SoCs
+    - ACPI: resource: Add Infinity laptops to irq1_edge_low_force_override
+    - ACPI: resource: Do IRQ override on Lunnen Ground laptops
+    - ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override
+    - ACPI: scan: Fix device check notification handling
+    - x86, relocs: Ignore relocations in .notes section
+    - SUNRPC: fix some memleaks in gssx_dec_option_array
+    - mmc: wmt-sdmmc: remove an incorrect release_mem_region() call in the .remove
+      function
+    - wifi: rtw88: 8821c: Fix false alarm count
+    - PCI: Make pci_dev_is_disconnected() helper public for other drivers
+    - iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected
+    - igb: move PEROUT and EXTTS isr logic to separate functions
+    - igb: Fix missing time sync events
+    - Bluetooth: Remove superfluous call to hci_conn_check_pending()
+    - Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855
+    - Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()
+    - Bluetooth: hci_core: Fix possible buffer overflow
+    - sr9800: Add check for usbnet_get_endpoints
+    - bpf: Fix DEVMAP_HASH overflow check on 32-bit arches
+    - bpf: Fix hashtab overflow check on 32-bit arches
+    - bpf: Fix stackmap overflow check on 32-bit arches
+    - ipv6: fib6_rules: flush route cache when rule is changed
+    - net: ip_tunnel: make sure to pull inner header in ip_tunnel_rcv()
+    - net: phy: fix phy_get_internal_delay accessing an empty array
+    - net: hns3: fix kernel crash when 1588 is received on HIP08 devices
+    - net: hns3: fix port duplex configure error in IMP reset
+    - net: phy: DP83822: enable rgmii mode if phy_interface_is_rgmii
+    - net: phy: dp83822: Fix RGMII TX delay configuration
+    - OPP: debugfs: Fix warning around icc_get_name()
+    - tcp: fix incorrect parameter validation in the do_tcp_getsockopt() function
+    - net: Change sock_getsockopt() to take the sk ptr instead of the sock ptr
+    - bpf: net: Change sk_getsockopt() to take the sockptr_t argument
+    - bpf: net: Change do_ip_getsockopt() to take the sockptr_t argument
+    - ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt()
+      function
+    - l2tp: fix incorrect parameter validation in the pppol2tp_getsockopt()
+      function
+    - udp: fix incorrect parameter validation in the udp_lib_getsockopt() function
+    - net: kcm: fix incorrect parameter validation in the kcm_getsockopt) function
+    - net/x25: fix incorrect parameter validation in the x25_getsockopt() function
+    - nfp: flower: handle acti_netdevs allocation failure
+    - dm raid: fix false positive for requeue needed during reshape
+    - dm: call the resume method on internal suspend
+    - drm/tegra: dsi: Add missing check for of_find_device_by_node
+    - drm/tegra: dpaux: Populate AUX bus
+    - drm/tegra: dpaux: Fix PM disable depth imbalance in tegra_dpaux_probe
+    - drm/tegra: dsi: Make use of the helper function dev_err_probe()
+    - drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()
+    - drm/tegra: dsi: Fix missing pm_runtime_disable() in the error handling path
+      of tegra_dsi_probe()
+    - drm/tegra: dc: rgb: Allow changing PLLD rate on Tegra30+
+    - drm/tegra: rgb: Fix some error handling paths in tegra_dc_rgb_probe()
+    - drm/tegra: rgb: Fix missing clk_put() in the error handling paths of
+      tegra_dc_rgb_probe()
+    - drm/tegra: output: Fix missing i2c_put_adapter() in the error handling paths
+      of tegra_output_probe()
+    - drm/rockchip: inno_hdmi: Fix video timing
+    - drm: Don't treat 0 as -1 in drm_fixp2int_ceil
+    - drm/ttm: add ttm_resource_fini v2
+    - drm/vmwgfx: fix a memleak in vmw_gmrid_man_get_node
+    - drm/rockchip: lvds: do not overwrite error code
+    - drm/rockchip: lvds: do not print scary message when probing defer
+    - drm/lima: fix a memleak in lima_heap_alloc
+    - dmaengine: tegra210-adma: Update dependency to ARCH_TEGRA
+    - [Config]: update CONFIG_TEGRA210_ADMA
+    - media: tc358743: register v4l2 async device only after successful setup
+    - PCI/DPC: Print all TLP Prefixes, not just the first
+    - perf record: Fix possible incorrect free in record__switch_output()
+    - HID: lenovo: Add middleclick_workaround sysfs knob for cptkbd
+    - drm/amd/display: Fix a potential buffer overflow in 'dp_dsc_clock_en_read()'
+    - drm/amd/display: Fix potential NULL pointer dereferences in
+      'dcn10_set_output_transfer_func()'
+    - perf evsel: Fix duplicate initialization of data->id in
+      evsel__parse_sample()
+    - clk: meson: Add missing clocks to axg_clk_regmaps
+    - media: em28xx: annotate unchecked call to media_device_register()
+    - media: v4l2-tpg: fix some memleaks in tpg_alloc
+    - media: v4l2-mem2mem: fix a memleak in v4l2_m2m_register_entity
+    - media: edia: dvbdev: fix a use-after-free
+    - pinctrl: mediatek: Drop bogus slew rate register range for MT8192
+    - clk: qcom: reset: Commonize the de/assert functions
+    - clk: qcom: reset: Ensure write completion on reset de/assertion
+    - quota: simplify drop_dquot_ref()
+    - quota: Fix potential NULL pointer dereference
+    - quota: Fix rcu annotations of inode dquot pointers
+    - PCI/P2PDMA: Fix a sleeping issue in a RCU read section
+    - PCI: switchtec: Fix an error handling path in switchtec_pci_probe()
+    - crypto: xilinx - call finalize with bh disabled
+    - perf thread_map: Free strlist on normal path in thread_map__new_by_tid_str()
+    - drm/radeon/ni: Fix wrong firmware size logging in ni_init_microcode()
+    - ALSA: seq: fix function cast warnings
+    - perf stat: Avoid metric-only segv
+    - ASoC: meson: Use dev_err_probe() helper
+    - ASoC: meson: aiu: fix function pointer type mismatch
+    - ASoC: meson: t9015: fix function pointer type mismatch
+    - powerpc: Force inlining of arch_vmap_p{u/m}d_supported()
+    - PCI: endpoint: Support NTB transfer between RC and EP
+    - [Config]: update CONFIG_PCI_EPF_VNTB
+    - NTB: EPF: fix possible memory leak in pci_vntb_probe()
+    - NTB: fix possible name leak in ntb_register_device()
+    - media: sun8i-di: Fix coefficient writes
+    - media: sun8i-di: Fix power on/off sequences
+    - media: sun8i-di: Fix chroma difference threshold
+    - media: imx: csc/scaler: fix v4l2_ctrl_handler memory leak
+    - media: go7007: add check of return value of go7007_read_addr()
+    - media: pvrusb2: remove redundant NULL check
+    - media: pvrusb2: fix pvr2_stream_callback casts
+    - clk: qcom: dispcc-sdm845: Adjust internal GDSC wait times
+    - drm/mediatek: dsi: Fix DSI RGB666 formats and definitions
+    - PCI: Mark 3ware-9650SE Root Port Extended Tags as broken
+    - clk: hisilicon: hi3519: Release the correct number of gates in
+      hi3519_clk_unregister()
+    - clk: hisilicon: hi3559a: Fix an erroneous devm_kfree()
+    - drm/tegra: put drm_gem_object ref on error in tegra_fb_create
+    - mfd: syscon: Call of_node_put() only when of_parse_phandle() takes a ref
+    - mfd: altera-sysmgr: Call of_node_put() only when of_parse_phandle() takes a
+      ref
+    - crypto: arm/sha - fix function cast warnings
+    - drm/tidss: Fix initial plane zpos values
+    - mtd: maps: physmap-core: fix flash size larger than 32-bit
+    - mtd: rawnand: lpc32xx_mlc: fix irq handler prototype
+    - ASoC: meson: axg-tdm-interface: fix mclk setup without mclk-fs
+    - ASoC: meson: axg-tdm-interface: add frame rate constraint
+    - HID: amd_sfh: Update HPD sensor structure elements
+    - drm/amdgpu: Fix missing break in ATOM_ARG_IMM Case of atom_get_src_int()
+    - media: pvrusb2: fix uaf in pvr2_context_set_notify
+    - media: dvb-frontends: avoid stack overflow warnings with clang
+    - media: go7007: fix a memleak in go7007_load_encoder
+    - media: ttpci: fix two memleaks in budget_av_attach
+    - media: mediatek: vcodec: avoid -Wcast-function-type-strict warning
+    - drm/mediatek: Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
+    - powerpc/hv-gpci: Fix the H_GET_PERF_COUNTER_INFO hcall return value checks
+    - drm/msm/dpu: add division of drm_display_mode's hskew parameter
+    - module: Add support for default value for module async_probe
+    - modules: wait do_free_init correctly
+    - powerpc/embedded6xx: Fix no previous prototype for avr_uart_send() etc.
+    - leds: aw2013: Unlock mutex before destroying it
+    - leds: sgm3140: Add missing timer cleanup and flash gpio control
+    - backlight: lm3630a: Initialize backlight_properties on init
+    - backlight: lm3630a: Don't set bl->props.brightness in get_brightness
+    - backlight: da9052: Fully initialize backlight_properties during probe
+    - backlight: lm3639: Fully initialize backlight_properties during probe
+    - backlight: lp8788: Fully initialize backlight_properties during probe
+    - sparc32: Fix section mismatch in leon_pci_grpci
+    - clk: Fix clk_core_get NULL dereference
+    - clk: zynq: Prevent null pointer dereference caused by kmalloc failure
+    - ALSA: hda/realtek: fix ALC285 issues on HP Envy x360 laptops
+    - ALSA: usb-audio: Stop parsing channels bits when all channels are found.
+    - RDMA/srpt: Do not register event handler until srpt device is fully setup
+    - f2fs: multidevice: support direct IO
+    - f2fs: invalidate META_MAPPING before IPU/DIO write
+    - f2fs: replace congestion_wait() calls with io_schedule_timeout()
+    - f2fs: fix to invalidate META_MAPPING before DIO write
+    - f2fs: invalidate meta pages only for post_read required inode
+    - f2fs: reduce stack memory cost by using bitfield in struct f2fs_io_info
+    - f2fs: compress: fix to cover normal cluster write with cp_rwsem
+    - f2fs: compress: fix to check unreleased compressed cluster
+    - scsi: csiostor: Avoid function pointer casts
+    - RDMA/device: Fix a race between mad_client and cm_client init
+    - RDMA/rtrs-clt: Check strnlen return len in sysfs mpath_policy_store()
+    - scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
+    - net: sunrpc: Fix an off by one in rpc_sockaddr2uaddr()
+    - NFSv4.2: fix nfs4_listxattr kernel BUG at mm/usercopy.c:102
+    - NFSv4.2: fix listxattr maximum XDR buffer size
+    - watchdog: stm32_iwdg: initialize default timeout
+    - NFS: Fix an off by one in root_nfs_cat()
+    - f2fs: compress: fix reserve_cblocks counting error when out of space
+    - afs: Revert "afs: Hide silly-rename files from userspace"
+    - comedi: comedi_test: Prevent timers rescheduling during deletion
+    - remoteproc: stm32: use correct format strings on 64-bit
+    - remoteproc: stm32: Fix incorrect type in assignment for va
+    - remoteproc: stm32: Fix incorrect type assignment returned by
+      stm32_rproc_get_loaded_rsc_tablef
+    - tty: vt: fix 20 vs 0x20 typo in EScsiignore
+    - serial: max310x: fix syntax error in IRQ error message
+    - tty: serial: samsung: fix tx_empty() to return TIOCSER_TEMT
+    - arm64: dts: broadcom: bcmbca: bcm4908: drop invalid switch cells
+    - kconfig: fix infinite loop when expanding a macro at the end of file
+    - rtc: mt6397: select IRQ_DOMAIN instead of depending on it
+    - serial: 8250_exar: Don't remove GPIO device on suspend
+    - staging: greybus: fix get_channel_from_mode() failure path
+    - usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
+    - io_uring: don't save/restore iowait state
+    - nouveau: reset the bo resource bus info after an eviction
+    - octeontx2-af: Use matching wake_up API variant in CGX command interface
+    - s390/vtime: fix average steal time calculation
+    - soc: fsl: dpio: fix kcalloc() argument order
+    - hsr: Fix uninit-value access in hsr_get_node()
+    - net: mtk_eth_soc: move MAC_MCR setting to mac_finish()
+    - net: mediatek: mtk_eth_soc: clear MAC_MCR_FORCE_LINK only when MAC is up
+    - net: ethernet: mtk_eth_soc: fix PPE hanging issue
+    - packet: annotate data-races around ignore_outgoing
+    - net: veth: do not manipulate GRO when using XDP
+    - net: dsa: mt7530: prevent possible incorrect XTAL frequency selection
+    - vdpa/mlx5: Allow CVQ size changes
+    - wireguard: receive: annotate data-race around receiving_counter.counter
+    - rds: introduce acquire/release ordering in acquire/release_in_xmit()
+    - hsr: Handle failures in module init
+    - net: phy: fix phy_read_poll_timeout argument type in genphy_loopback
+    - net/bnx2x: Prevent access to a freed page in page_pool
+    - octeontx2-af: Use separate handlers for interrupts
+    - netfilter: nf_tables: do not compare internal table flags on updates
+    - rcu: add a helper to report consolidated flavor QS
+    - net: report RCU QS on threaded NAPI repolling
+    - bpf: report RCU QS in cpumap kthread
+    - net: dsa: mt7530: fix handling of LLDP frames
+    - net: dsa: mt7530: fix handling of 802.1X PAE frames
+    - net: dsa: mt7530: fix link-local frames that ingress vlan filtering ports
+    - net: dsa: mt7530: fix handling of all link-local frames
+    - spi: spi-mt65xx: Fix NULL pointer access in interrupt handler
+    - regmap: Add missing map->bus check
+    - remoteproc: stm32: fix incorrect optional pointers
+  * Jammy update: v5.15.152 upstream stable release (LP: #2063276)
+    - mmc: mmci: stm32: use a buffer for unaligned DMA requests
+    - mmc: mmci: stm32: fix DMA API overlapping mappings warning
+    - net: lan78xx: fix runtime PM count underflow on link stop
+    - ixgbe: {dis, en}able irqs in ixgbe_txrx_ring_{dis, en}able
+    - i40e: disable NAPI right after disabling irqs when handling xsk_pool
+    - tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string
+    - geneve: make sure to pull inner header in geneve_rx()
+    - net: sparx5: Fix use after free inside sparx5_del_mact_entry
+    - net: ice: Fix potential NULL pointer dereference in ice_bridge_setlink()
+    - net/ipv6: avoid possible UAF in ip6_route_mpath_notify()
+    - cpumap: Zero-initialise xdp_rxq_info struct before running XDP program
+    - net/rds: fix WARNING in rds_conn_connect_if_down
+    - netfilter: nft_ct: fix l3num expectations with inet pseudo family
+    - netfilter: nf_conntrack_h323: Add protection for bmp length out of range
+    - erofs: apply proper VMA alignment for memory mapped files on THP
+    - netrom: Fix a data-race around sysctl_netrom_default_path_quality
+    - netrom: Fix a data-race around sysctl_netrom_obsolescence_count_initialiser
+    - netrom: Fix data-races around sysctl_netrom_network_ttl_initialiser
+    - netrom: Fix a data-race around sysctl_netrom_transport_timeout
+    - netrom: Fix a data-race around sysctl_netrom_transport_maximum_tries
+    - netrom: Fix a data-race around sysctl_netrom_transport_acknowledge_delay
+    - netrom: Fix a data-race around sysctl_netrom_transport_busy_delay
+    - netrom: Fix a data-race around sysctl_netrom_transport_requested_window_size
+    - netrom: Fix a data-race around sysctl_netrom_transport_no_activity_timeout
+    - netrom: Fix a data-race around sysctl_netrom_routing_control
+    - netrom: Fix a data-race around sysctl_netrom_link_fails_count
+    - netrom: Fix data-races around sysctl_net_busy_read
+    - ALSA: usb-audio: Refcount multiple accesses on the single clock
+    - ALSA: usb-audio: Clear fixed clock rate at closing EP
+    - ALSA: usb-audio: Split endpoint setups for hw_params and prepare (take#2)
+    - ALSA: usb-audio: Properly refcounting clock rate
+    - ALSA: usb-audio: Apply mutex around snd_usb_endpoint_set_params()
+    - ALSA: usb-audio: Correct the return code from snd_usb_endpoint_set_params()
+    - ALSA: usb-audio: Avoid superfluous endpoint setup
+    - ALSA: usb-audio: Add quirk for Tascam Model 12
+    - ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
+    - ALSA: usb-audio: Fix microphone sound on Nexigo webcam.
+    - ALSA: usb-audio: add quirk for RODE NT-USB+
+    - drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd()
+      & write_dpcd()' functions
+    - nfp: flower: add goto_chain_index for ct entry
+    - nfp: flower: add hardware offload check for post ct entry
+    - selftests/mm: switch to bash from sh
+    - selftests: mm: fix map_hugetlb failure on 64K page size systems
+    - xhci: process isoc TD properly when there was a transaction error mid TD.
+    - xhci: handle isoc Babble and Buffer Overrun events properly
+    - serial: max310x: use regmap methods for SPI batch operations
+    - serial: max310x: use a separate regmap for each port
+    - serial: max310x: prevent infinite while() loop in port startup
+    - drm/amd/pm: do not expose the API used internally only in kv_dpm.c
+    - drm/amdgpu: Reset IH OVERFLOW_CLEAR bit
+    - selftests: mptcp: decrease BW in simult flows
+    - hv_netvsc: use netif_is_bond_master() instead of open code
+    - hv_netvsc: Register VF in netvsc_probe if NET_DEVICE_REGISTER missed
+    - drm/amd/display: Re-arrange FPU code structure for dcn2x
+    - drm/amd/display: move calcs folder into DML
+    - drm/amd/display: remove DML Makefile duplicate lines
+    - drm/amd/display: Increase frame-larger-than for all display_mode_vba files
+    - getrusage: add the "signal_struct *sig" local variable
+    - getrusage: move thread_group_cputime_adjusted() outside of
+      lock_task_sighand()
+    - getrusage: use __for_each_thread()
+    - getrusage: use sig->stats_lock rather than lock_task_sighand()
+    - proc: Use task_is_running() for wchan in /proc/$pid/stat
+    - fs/proc: do_task_stat: move thread_group_cputime_adjusted() outside of
+      lock_task_sighand()
+    - ALSA: usb-audio: Fix wrong kfree issue in snd_usb_endpoint_free_all
+    - ALSA: usb-audio: Always initialize fixed_rate in
+      snd_usb_find_implicit_fb_sync_format()
+    - ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
+    - ALSA: usb-audio: Sort quirk table entries
+    - regmap: allow to define reg_update_bits for no bus configuration
+    - regmap: Add bulk read/write callbacks into regmap_config
+    - serial: max310x: make accessing revision id interface-agnostic
+    - serial: max310x: fix IO data corruption in batched operations
+    - Linux 5.15.152
+  * CVE-2024-26809
+    - netfilter: nft_set_pipapo: release elements in clone only from destroy path
+  * CVE-2024-26792
+    - btrfs: fix double free of anonymous device after snapshot creation failure
+  * CVE-2023-52530
+    - wifi: mac80211: fix potential key use-after-free
+  * CVE-2023-52447
+    - bpf: Defer the free of inner map when necessary
+    - rcu-tasks: Provide rcu_trace_implies_rcu_gp()
+  * Avoid creating non-working backlight sysfs knob from ASUS board
+    (LP: #2060422)
+    - platform/x86: asus-wmi: Consider device is absent when the read is ~0
+  * [Ubuntu 22.04.4/linux-image-6.5.0-26-generic] Kernel output "UBSAN: array-
+    index-out-of-bounds in /build/linux-hwe-6.5-34pCLi/linux-
+    hwe-6.5-6.5.0/drivers/net/hyperv/netvsc.c:1445:41" multiple times,
+    especially during boot. (LP: #2058477)
+    - hv: hyperv.h: Replace one-element array with flexible-array member
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209)
+    - netfilter: nf_tables: disallow timeout for anonymous sets
+    - mtd: spinand: gigadevice: Fix the get ecc status issue
+    - netlink: Fix kernel-infoleak-after-free in __skb_datagram_iter
+    - net: ip_tunnel: prevent perpetual headroom growth
+    - tun: Fix xdp_rxq_info's queue_index when detaching
+    - cpufreq: intel_pstate: fix pstate limits enforcement for adjust_perf call
+      back
+    - net: veth: clear GRO when clearing XDP even when down
+    - ipv6: fix potential "struct net" leak in inet6_rtm_getaddr()
+    - lan78xx: enable auto speed configuration for LAN7850 if no EEPROM is
+      detected
+    - net: enable memcg accounting for veth queues
+    - veth: try harder when allocating queue memory
+    - net: usb: dm9601: fix wrong return value in dm9601_mdio_read
+    - uapi: in6: replace temporary label with rfc9486
+    - stmmac: Clear variable when destroying workqueue
+    - Bluetooth: Avoid potential use-after-free in hci_error_reset
+    - Bluetooth: hci_event: Fix wrongly recorded wakeup BD_ADDR
+    - netfilter: nf_tables: allow NFPROTO_INET in nft_(match/target)_validate()
+    - netfilter: nfnetlink_queue: silence bogus compiler warning
+    - netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
+    - netfilter: make function op structures const
+    - netfilter: let reset rules clean out conntrack entries
+    - netfilter: bridge: confirm multicast packets before passing them up the
+      stack
+    - rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
+    - igb: extend PTP timestamp adjustments to i211
+    - efi/capsule-loader: fix incorrect allocation size
+    - power: supply: bq27xxx-i2c: Do not free non existing IRQ
+    - ALSA: Drop leftover snd-rtctimer stuff from Makefile
+    - fbcon: always restore the old font data in fbcon_do_set_font()
+    - afs: Fix endless loop in directory parsing
+    - riscv: Sparse-Memory/vmemmap out-of-bounds fix
+    - ALSA: firewire-lib: fix to check cycle continuity
+    - gtp: fix use-after-free and null-ptr-deref in gtp_newlink()
+    - wifi: nl80211: reject iftype change with mesh ID change
+    - btrfs: dev-replace: properly validate device names
+    - dmaengine: fsl-qdma: fix SoC may hang on 16 byte unaligned read
+    - dmaengine: ptdma: use consistent DMA masks
+    - dmaengine: fsl-qdma: init irq after reg initialization
+    - mmc: core: Fix eMMC initialization with 1-bit bus connection
+    - mmc: sdhci-xenon: add timeout for PHY init complete
+    - mmc: sdhci-xenon: fix PHY init clock stability
+    - pmdomain: qcom: rpmhpd: Fix enabled_corner aggregation
+    - x86/cpu/intel: Detect TME keyid bits before setting MTRR mask registers
+    - mptcp: move __mptcp_error_report in protocol.c
+    - mptcp: process pending subflow error on close
+    - mptcp: rename timer related helper to less confusing names
+    - selftests: mptcp: add missing kconfig for NF Filter
+    - selftests: mptcp: add missing kconfig for NF Filter in v6
+    - mptcp: clean up harmless false expressions
+    - mptcp: add needs_id for netlink appending addr
+    - mptcp: push at DSS boundaries
+    - mptcp: fix possible deadlock in subflow diag
+    - cachefiles: fix memory leak in cachefiles_add_cache()
+    - fs,hugetlb: fix NULL pointer dereference in hugetlbs_fill_super
+    - Revert "drm/bridge: lt8912b: Register and attach our DSI device at probe"
+    - af_unix: Drop oob_skb ref before purging queue in GC.
+    - gpio: 74x164: Enable output pins after registers are reset
+    - gpiolib: Fix the error path order in gpiochip_add_data_with_key()
+    - gpio: fix resource unwinding order in error path
+    - Revert "interconnect: Fix locking for runpm vs reclaim"
+    - Revert "interconnect: Teach lockdep about icc_bw_lock order"
+    - bpf: Add BPF_FIB_LOOKUP_SKIP_NEIGH for bpf_fib_lookup
+    - bpf: Add table ID to bpf_fib_lookup BPF helper
+    - bpf: Derive source IP addr via bpf_*_fib_lookup()
+    - Linux 5.15.151
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209) //
+    CVE-2024-26782
+    - mptcp: fix double-free on socket dismantle
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209) // Fix
+    bluetooth connections with 3.0 device (LP: #2063067)
+    - Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142)
+    - net/sched: Retire CBQ qdisc
+    - [Config] updateconfigs for NET_SCH_CBQ
+    - net/sched: Retire ATM qdisc
+    - [Config] updateconfigs for NET_SCH_ATM
+    - net/sched: Retire dsmark qdisc
+    - [Config] updateconfigs for NET_SCH_DSMARK
+    - smb: client: fix potential OOBs in smb2_parse_contexts()
+    - smb: client: fix parsing of SMB3.1.1 POSIX create context
+    - sched/rt: sysctl_sched_rr_timeslice show default timeslice after reset
+    - PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
+    - bpf: Merge printk and seq_printf VARARG max macros
+    - bpf: Add struct for bin_args arg in bpf_bprintf_prepare
+    - bpf: Do cleanup in bpf_bprintf_cleanup only when needed
+    - bpf: Remove trace_printk_lock
+    - userfaultfd: fix mmap_changing checking in mfill_atomic_hugetlb
+    - zonefs: Improve error handling
+    - x86/fpu: Stop relying on userspace for info to fault in xsave buffer
+    - sched/rt: Fix sysctl_sched_rr_timeslice intial value
+    - sched/rt: Disallow writing invalid values to sched_rt_period_us
+    - scsi: target: core: Add TMF to tmr_list handling
+    - dmaengine: shdma: increase size of 'dev_id'
+    - dmaengine: fsl-qdma: increase size of 'irq_name'
+    - wifi: cfg80211: fix missing interfaces when dumping
+    - wifi: mac80211: fix race condition on enabling fast-xmit
+    - fbdev: savage: Error out if pixclock equals zero
+    - fbdev: sis: Error out if pixclock equals zero
+    - spi: hisi-sfc-v3xx: Return IRQ_NONE if no interrupts were detected
+    - ahci: asm1166: correct count of reported ports
+    - ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers
+    - MIPS: reserve exception vector space ONLY ONCE
+    - platform/x86: touchscreen_dmi: Add info for the TECLAST X16 Plus tablet
+    - ext4: avoid dividing by 0 in mb_update_avg_fragment_size() when block bitmap
+      corrupt
+    - ext4: avoid allocating blocks from corrupted group in
+      ext4_mb_try_best_found()
+    - ext4: avoid allocating blocks from corrupted group in ext4_mb_find_by_goal()
+    - dmaengine: ti: edma: Add some null pointer checks to the edma_probe
+    - regulator: pwm-regulator: Add validity checks in continuous .get_voltage
+    - nvmet-tcp: fix nvme tcp ida memory leak
+    - ALSA: usb-audio: Check presence of valid altsetting control
+    - ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616
+    - spi: sh-msiof: avoid integer overflow in constants
+    - Input: xpad - add Lenovo Legion Go controllers
+    - netfilter: conntrack: check SCTP_CID_SHUTDOWN_ACK for vtag setting in
+      sctp_new
+    - ALSA: usb-audio: Ignore clock selector errors for single connection
+    - nvme-fc: do not wait in vain when unloading module
+    - nvmet-fcloop: swap the list_add_tail arguments
+    - nvmet-fc: release reference on target port
+    - nvmet-fc: defer cleanup using RCU properly
+    - nvmet-fc: hold reference on hostport match
+    - nvmet-fc: abort command when there is no binding
+    - nvmet-fc: avoid deadlock on delete association path
+    - nvmet-fc: take ref count on tgtport before delete assoc
+    - ext4: correct the hole length returned by ext4_map_blocks()
+    - Input: i8042 - add Fujitsu Lifebook U728 to i8042 quirk table
+    - fs/ntfs3: Modified fix directory element type detection
+    - fs/ntfs3: Improve ntfs_dir_count
+    - fs/ntfs3: Correct hard links updating when dealing with DOS names
+    - fs/ntfs3: Print warning while fixing hard links count
+    - fs/ntfs3: Fix detected field-spanning write (size 8) of single field
+      "le->name"
+    - fs/ntfs3: Add NULL ptr dereference checking at the end of
+      attr_allocate_frame()
+    - fs/ntfs3: Disable ATTR_LIST_ENTRY size check
+    - fs/ntfs3: use non-movable memory for ntfs3 MFT buffer cache
+    - fs/ntfs3: Prevent generic message "attempt to access beyond end of device"
+    - fs/ntfs3: Correct function is_rst_area_valid
+    - fs/ntfs3: Update inode->i_size after success write into compressed file
+    - fs/ntfs3: Fix oob in ntfs_listxattr
+    - wifi: mac80211: adding missing drv_mgd_complete_tx() call
+    - efi: runtime: Fix potential overflow of soft-reserved region size
+    - efi: Don't add memblocks for soft-reserved memory
+    - hwmon: (coretemp) Enlarge per package core count limit
+    - scsi: lpfc: Use unsigned type for num_sge
+    - firewire: core: send bus reset promptly on gap count error
+    - drm/amdgpu: skip to program GFXDEC registers for suspend abort
+    - drm/amdgpu: reset gpu for s3 suspend abort case
+    - virtio-blk: Ensure no requests in virtqueues before deleting vqs.
+    - pmdomain: mediatek: fix race conditions with genpd
+    - ksmbd: free aux buffer if ksmbd_iov_pin_rsp_read fails
+    - pmdomain: renesas: r8a77980-sysc: CR7 must be always on
+    - erofs: fix lz4 inplace decompression
+    - IB/hfi1: Fix sdma.h tx->num_descs off-by-one error
+    - drm/ttm: Fix an invalid freeing on already freed page in error path
+    - dm-crypt: don't modify the data when using authenticated encryption
+    - platform/x86: intel-vbtn: Stop calling "VBDL" from notify_handler
+    - platform/x86: touchscreen_dmi: Allow partial (prefix) matches for ACPI names
+    - KVM: arm64: vgic-its: Test for valid IRQ in MOVALL handler
+    - KVM: arm64: vgic-its: Test for valid IRQ in its_sync_lpi_pending_table()
+    - gtp: fix use-after-free and null-ptr-deref in gtp_genl_dump_pdp()
+    - PCI/MSI: Prevent MSI hardware interrupt number truncation
+    - l2tp: pass correct message length to ip6_append_data
+    - ARM: ep93xx: Add terminator to gpiod_lookup_table
+    - Revert "x86/ftrace: Use alternative RET encoding"
+    - x86/text-patching: Make text_gen_insn() play nice with ANNOTATE_NOENDBR
+    - x86/ibt,paravirt: Use text_gen_insn() for paravirt_patch()
+    - x86/ftrace: Use alternative RET encoding
+    - x86/returnthunk: Allow different return thunks
+    - Revert "x86/alternative: Make custom return thunk unconditional"
+    - x86/alternative: Make custom return thunk unconditional
+    - serial: amba-pl011: Fix DMA transmission in RS485 mode
+    - usb: dwc3: gadget: Don't disconnect if not started
+    - usb: cdnsp: blocked some cdns3 specific code
+    - usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
+    - usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
+    - usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
+    - usb: roles: fix NULL pointer issue when put module's reference
+    - usb: roles: don't get/set_role() when usb_role_switch is unregistered
+    - mptcp: fix lockless access in subflow ULP diag
+    - clk: imx: imx8mp: add shared clk gate for usb suspend clk
+    - clk: qcom: gcc-qcs404: disable gpll[04]_out_aux parents
+    - clk: qcom: gcc-qcs404: fix names of the DSI clocks used as parents
+    - mtd: rawnand: sunxi: Fix the size of the last OOB region
+    - RISC-V: fix funct4 definition for c.jalr in parse_asm.h
+    - Input: iqs269a - drop unused device node references
+    - Input: iqs269a - configure device with a single block write
+    - Input: iqs269a - increase interrupt handler return delay
+    - clk: renesas: cpg-mssr: Fix use after free if cpg_mssr_common_init() failed
+    - Input: ads7846 - don't report pressure for ads7845
+    - clk: renesas: cpg-mssr: Remove superfluous check in resume code
+    - clk: imx: avoid memory leak
+    - Input: ads7846 - always set last command to PWRDOWN
+    - Input: ads7846 - don't check penirq immediately for 7845
+    - powerpc/powernv/ioda: Skip unallocated resources when mapping to PE
+    - clk: qcom: gpucc-sc7180: fix clk_dis_wait being programmed for CX GDSC
+    - clk: qcom: gpucc-sdm845: fix clk_dis_wait being programmed for CX GDSC
+    - clk: Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
+    - powerpc/pseries/lparcfg: add missing RTAS retry status handling
+    - powerpc/perf/hv-24x7: add missing RTAS retry status handling
+    - powerpc/pseries/lpar: add missing RTAS retry status handling
+    - MIPS: SMP-CPS: fix build error when HOTPLUG_CPU not set
+    - MIPS: vpe-mt: drop physical_memsize
+    - vdpa/mlx5: Don't clear mr struct on destroy MR
+    - ARM: dts: BCM53573: Drop nonexistent #usb-cells
+    - RDMA/siw: Balance the reference of cep->kref in the error path
+    - RDMA/siw: Correct wrong debug message
+    - clk: linux/clk-provider.h: fix kernel-doc warnings and typos
+    - platform/x86: asus-wmi: Document the dgpu_disable sysfs attribute
+    - acpi: property: Let args be NULL in __acpi_node_get_property_reference
+    - ARM: dts: BCM53573: Drop nonexistent "default-off" LED trigger
+    - tools headers UAPI: Sync linux/fscrypt.h with the kernel sources
+    - perf beauty: Update copy of linux/socket.h with the kernel sources
+    - tools/virtio: fix build
+    - drm/amdgpu: init iommu after amdkfd device init
+    - f2fs: don't set GC_FAILURE_PIN for background GC
+    - f2fs: write checkpoint during FG_GC
+    - drm/i915/dg1: Update DMC_DEBUG3 register
+    - kernel/sched: Remove dl_boosted flag comment
+    - cifs: remove useless parameter 'is_fsctl' from SMB2_ioctl()
+    - serial: 8250: Remove serial_rs485 sanitization from em485
+    - clk: imx8mp: Add DISP2 pixel clock
+    - clk: imx8mp: add clkout1/2 support
+    - dt-bindings: clocks: imx8mp: Add ID for usb suspend clock
+    - net: ethernet: ti: add missing of_node_put before return
+    - powerpc/rtas: make all exports GPL
+    - powerpc/rtas: ensure 4KB alignment for rtas_data_buf
+    - powerpc/eeh: Small refactor of eeh_handle_normal_event()
+    - powerpc/eeh: Set channel state after notifying the drivers
+    - PM: core: Redefine pm_ptr() macro
+    - PM: core: Add new *_PM_OPS macros, deprecate old ones
+    - mmc: jz4740: Use the new PM macros
+    - mmc: mxc: Use the new PM macros
+    - PM: core: Remove static qualifier in DEFINE_SIMPLE_DEV_PM_OPS macro
+    - Input: iqs269a - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
+    - Input: iqs269a - do not poll during suspend or resume
+    - Input: iqs269a - do not poll during ATI
+    - net/sched: Refactor qdisc_graft() for ingress and clsact Qdiscs
+    - netfilter: nf_tables: add rescheduling points during loop detection walks
+    - debugobjects: Recheck debug_objects_enabled before reporting
+    - nbd: Add the maximum limit of allocated index in nbd_dev_add
+    - md: fix data corruption for raid456 when reshape restart while grow up
+    - md/raid10: prevent soft lockup while flush writes
+    - posix-timers: Ensure timer ID search-loop limit is valid
+    - btrfs: add xxhash to fast checksum implementations
+    - ACPI: button: Add lid disable DMI quirk for Nextbook Ares 8A
+    - ACPI: video: Add backlight=native DMI quirk for Apple iMac11,3
+    - ACPI: video: Add backlight=native DMI quirk for Lenovo ThinkPad X131e (3371
+      AMD version)
+    - arm64: set __exception_irq_entry with __irq_entry as a default
+    - arm64: mm: fix VA-range sanity check
+    - sched/fair: Don't balance task to its current running CPU
+    - wifi: ath11k: fix registration of 6Ghz-only phy without the full channel
+      range
+    - bpf: Address KCSAN report on bpf_lru_list
+    - devlink: report devlink_port_type_warn source device
+    - wifi: wext-core: Fix -Wstringop-overflow warning in
+      ioctl_standard_iw_point()
+    - wifi: iwlwifi: mvm: avoid baid size integer overflow
+    - exfat: support dynamic allocate bh for exfat_entry_set_cache
+    - arm64: dts: rockchip: fix regulator name on rk3399-rock-4
+    - arm64: dts: rockchip: add ES8316 codec for ROCK Pi 4
+    - arm64: dts: rockchip: add SPDIF node for ROCK Pi 4
+    - ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
+    - ACPI: video: Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
+    - ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA
+    - ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
+    - ACPI: resource: Skip IRQ override on Asus Expertbook B2402CBA
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1502CBA
+    - xhci: cleanup xhci_hub_control port references
+    - xhci: move port specific items such as state completions to port structure
+    - xhci: rename resume_done to resume_timestamp
+    - xhci: clear usb2 resume related variables in one place.
+    - xhci: decouple usb2 port resume and get_port_status request handling
+    - xhci: track port suspend state correctly in unsuccessful resume cases
+    - cifs: add a warning when the in-flight count goes negative
+    - IB/hfi1: Fix a memleak in init_credit_return
+    - RDMA/bnxt_re: Return error for SRQ resize
+    - RDMA/irdma: Fix KASAN issue with tasklet
+    - RDMA/irdma: Validate max_send_wr and max_recv_wr
+    - RDMA/irdma: Set the CQ read threshold for GEN 1
+    - RDMA/irdma: Add AE for too many RNRS
+    - RDMA/srpt: Support specifying the srpt_service_guid parameter
+    - RDMA/qedr: Fix qedr_create_user_qp error flow
+    - arm64: dts: rockchip: set num-cs property for spi on px30
+    - RDMA/srpt: fix function pointer cast warnings
+    - bpf, scripts: Correct GPL license name
+    - scsi: jazz_esp: Only build if SCSI core is builtin
+    - nouveau: fix function cast warnings
+    - net: stmmac: Fix incorrect dereference in interrupt handlers
+    - ipv4: properly combine dev_base_seq and ipv4.dev_addr_genid
+    - ipv6: properly combine dev_base_seq and ipv6.dev_addr_genid
+    - ata: libahci_platform: Convert to using devm bulk clocks API
+    - ata: libahci_platform: Introduce reset assertion/deassertion methods
+    - ata: ahci_ceva: fix error handling for Xilinx GT PHY support
+    - bpf: Fix racing between bpf_timer_cancel_and_free and bpf_timer_cancel
+    - drm/nouveau/instmem: fix uninitialized_var.cocci warning
+    - octeontx2-af: Consider the action set by PF
+    - s390: use the correct count for __iowrite64_copy()
+    - netfilter: nf_tables: set dormant flag on hook register failure
+    - netfilter: flowtable: simplify route logic
+    - netfilter: nft_flow_offload: reset dst in route object after setting up flow
+    - netfilter: nft_flow_offload: release dst in case direct xmit path is used
+    - drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set
+    - drm/amd/display: Fix memory leak in dm_sw_fini()
+    - i2c: imx: Add timer for handling the stop condition
+    - i2c: imx: when being a target, mark the last read as processed
+    - fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio
+    - netfilter: nf_tables: fix scheduling-while-atomic splat
+    - ext4: regenerate buddy after block freeing failed if under fc replay
+    - ext4: avoid bb_free and bb_fragments inconsistency in mb_free_blocks()
+    - netfilter: nf_tables: can't schedule in nft_chain_validate
+    - r8169: use new PM macros
+    - Linux 5.15.150
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26733
+    - packet: move from strlcpy with unused retval to strscpy
+    - net: dev: Convert sa_data to flexible array in struct sockaddr
+    - arp: Prevent overflow in arp_req_get().
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26735
+    - ipv6: sr: fix possible use-after-free and null-ptr-deref
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26736
+    - afs: Increase buffer size in afs_update_volume_status()
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26748
+    - usb: cdns3: fix memory double free when handle zero packet
+  * CVE-2023-47233
+    - wifi: brcmfmac: Fix use-after-free bug in brcmf_cfg80211_detach
+  * CVE-2024-26584
+    - net: tls: handle backlogging of crypto requests
+  * CVE-2024-26585
+    - tls: fix race between tx work scheduling and socket close
+  * CVE-2024-26583
+    - tls: rx: jump to a more appropriate label
+    - tls: rx: drop pointless else after goto
+    - tls: stop recv() if initial process_rx_list gave us non-DATA
+    - tls: rx: don't store the record type in socket context
+    - tls: rx: don't store the decryption status in socket context
+    - tls: rx: don't issue wake ups when data is decrypted
+    - tls: rx: refactor decrypt_skb_update()
+    - tls: hw: rx: use return value of tls_device_decrypted() to carry status
+    - tls: rx: drop unnecessary arguments from tls_setup_from_iter()
+    - tls: rx: don't report text length from the bowels of decrypt
+    - tls: rx: wrap decryption arguments in a structure
+    - tls: rx: factor out writing ContentType to cmsg
+    - tls: rx: don't track the async count
+    - tls: rx: move counting TlsDecryptErrors for sync
+    - tls: rx: assume crypto always calls our callback
+    - tls: rx: use async as an in-out argument
+    - tls: decrement decrypt_pending if no async completion will be called
+    - net: tls: fix async vs NIC crypto offload
+    - Revert "tls: rx: move counting TlsDecryptErrors for sync"
+    - tls: rx: simplify async wait
+    - tls: rx: return the already-copied data on crypto error
+    - tls: rx: allow only one reader at a time
+    - tls: rx: release the sock lock on locking timeout
+    - tls: extract context alloc/initialization out of tls_set_sw_offload
+    - net: tls: factor out tls_*crypt_async_wait()
+    - tls: fix race between async notify and socket close
+  * CVE-2024-26622
+    - tomoyo: fix UAF write bug in tomoyo_write_control()
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Mon, 27 May 2024 17:29:36 +1000
+
+linux-xilinx-zynqmp (5.15.0-1029.33) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1029.33 -proposed tracker (LP: #2061809)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop getabis data
+    - [Packaging] drop ABI data
+    - [Packaging] debian.zynqmp/dkms-versions -- update from kernel-versions
+      (main/2024.04.01)
+
+  * Jammy update: v5.15.148 upstream stable release (LP: #2055145)
+    - [Config] update annotations for CONFIG_MMC_SDHCI_AM654
+
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014)
+    - [Config] updateconfigs for MFD_TI_AM335X_TSCADC
+
+  *  Backport AXI 1-wire host driver (LP: #2058707)
+    - dt-bindings: w1: Add AMD AXI w1 host and MAINTAINERS entry
+    - w1: Add AXI 1-wire host driver for AMD programmable logic IP core
+    - w1: amd_axi_w1: Explicitly include correct DT includes
+    - [Config] Enable CONFIG_W1_MASTER_AMD_AXI
+
+  * Unsupported platform 'ZynqMP KV260 revB (LP: #2058321)
+    - [Packaging] Add breaks on flash-kernel older than 3.104ubuntu20
+
+  * Update on-chip oscillator clock nodes for Kria (LP: #2055241)
+    - arm64: zynqmp: Sync clock labels with kr260 revB
+    - arm64: zynqmp: Describe 25MHz fixed clock for PL GEMs
+    - arm64: zynqmp: Fix kr260 clock wiring
+
+  [ Ubuntu: 5.15.0-106.116 ]
+
+  * jammy/linux: 5.15.0-106.116 -proposed tracker (LP: #2061812)
+  * CVE-2024-2201
+    - x86/bugs: Use sysfs_emit()
+    - KVM: x86: Update KVM-only leaf handling to allow for 100% KVM-only leafs
+    - KVM: x86: Advertise CPUID.(EAX=7,ECX=2):EDX[5:0] to userspace
+    - KVM: x86: Use a switch statement and macros in __feature_translate()
+    - x86/bugs: Change commas to semicolons in 'spectre_v2' sysfs file
+    - x86/syscall: Don't force use of indirect calls for system calls
+    - x86/bhi: Add support for clearing branch history at syscall entry
+    - x86/bhi: Define SPEC_CTRL_BHI_DIS_S
+    - x86/bhi: Enumerate Branch History Injection (BHI) bug
+    - x86/bhi: Add BHI mitigation knob
+    - x86/bhi: Mitigate KVM by default
+    - KVM: x86: Add BHI_NO
+    - [Config] Set CONFIG_BHI to enabled (auto)
+  * Drop fips-checks script from trees (LP: #2055083)
+    - [Packaging] Remove fips-checks script
+  * alsa/realtek: adjust max output valume for headphone on 2 LG machines
+    (LP: #2058573)
+    - ALSA: hda/realtek: fix the hp playback volume issue for LG machines
+  * A general-proteciton exception during guest migration to unsupported PKRU
+    machine (LP: #2032164)
+    - x86/fpu: Allow caller to constrain xfeatures when copying to uabi buffer
+    - KVM: x86: Constrain guest-supported xfeatures only at KVM_GET_XSAVE{2}
+  *  [ICX] [SPR] [ipc/msg] performance: Mitigate the lock contention with percpu
+    counter (LP: #2058485)
+    - ipc: check checkpoint_restore_ns_capable() to modify C/R proc files
+    - ipc/ipc_sysctl.c: remove fallback for !CONFIG_PROC_SYSCTL
+    - ipc: Store mqueue sysctls in the ipc namespace
+    - ipc: Store ipc sysctls in the ipc namespace
+    - ipc: Use the same namespace to modify and validate
+    - ipc: Remove extra1 field abuse to pass ipc namespace
+    - ipc: Check permissions for checkpoint_restart sysctls at open time
+    - percpu: add percpu_counter_add_local and percpu_counter_sub_local
+    - ipc/msg: mitigate the lock contention with percpu counter
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014)
+    - ksmbd: free ppace array on error in parse_dacl
+    - ksmbd: don't allow O_TRUNC open on read-only share
+    - ksmbd: validate mech token in session setup
+    - ksmbd: fix UAF issue in ksmbd_tcp_new_connection()
+    - ksmbd: only v2 leases handle the directory
+    - iio: adc: ad7091r: Set alert bit in config register
+    - iio: adc: ad7091r: Allow users to configure device events
+    - iio: adc: ad7091r: Enable internal vref if external vref is not supplied
+    - dmaengine: fix NULL pointer in channel unregistration function
+    - scsi: ufs: core: Simplify power management during async scan
+    - scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
+    - iio:adc:ad7091r: Move exports into IIO_AD7091R namespace.
+    - ext4: allow for the last group to be marked as trimmed
+    - btrfs: sysfs: validate scrub_speed_max value
+    - crypto: api - Disallow identical driver names
+    - PM: hibernate: Enforce ordering during image compression/decompression
+    - hwrng: core - Fix page fault dead lock on mmap-ed hwrng
+    - crypto: s390/aes - Fix buffer overread in CTR mode
+    - media: imx355: Enable runtime PM before registering async sub-device
+    - rpmsg: virtio: Free driver_override when rpmsg_remove()
+    - media: ov9734: Enable runtime PM before registering async sub-device
+    - mips: Fix max_mapnr being uninitialized on early stages
+    - bus: mhi: host: Drop chan lock before queuing buffers
+    - bus: mhi: host: Add spinlock to protect WP access when queueing TREs
+    - parisc/firmware: Fix F-extend for PDC addresses
+    - async: Split async_schedule_node_domain()
+    - async: Introduce async_schedule_dev_nocall()
+    - arm64: dts: qcom: sc7180: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sdm845: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sm8150: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sdm845: fix USB DP/DM HS PHY interrupts
+    - lsm: new security_file_ioctl_compat() hook
+    - scripts/get_abi: fix source path leak
+    - mmc: core: Use mrq.sbc in close-ended ffu
+    - mmc: mmc_spi: remove custom DMA mapped buffers
+    - rtc: Adjust failure return code for cmos_set_alarm()
+    - nouveau/vmm: don't set addr on the fail path to avoid warning
+    - ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path
+    - rename(): fix the locking of subdirectories
+    - ksmbd: set v2 lease version on lease upgrade
+    - ksmbd: fix potential circular locking issue in smb2_set_ea()
+    - ksmbd: don't increment epoch if current state and request state are same
+    - ksmbd: send lease break notification on FILE_RENAME_INFORMATION
+    - ksmbd: Add missing set_freezable() for freezable kthread
+    - net/smc: fix illegal rmb_desc access in SMC-D connection dump
+    - tcp: make sure init the accept_queue's spinlocks once
+    - bnxt_en: Wait for FLR to complete during probe
+    - vlan: skip nested type that is not IFLA_VLAN_QOS_MAPPING
+    - llc: make llc_ui_sendmsg() more robust against bonding changes
+    - llc: Drop support for ETH_P_TR_802_2.
+    - net/rds: Fix UBSAN: array-index-out-of-bounds in rds_cmsg_recv
+    - tracing: Ensure visibility when inserting an element into tracing_map
+    - afs: Hide silly-rename files from userspace
+    - tcp: Add memory barrier to tcp_push()
+    - netlink: fix potential sleeping issue in mqueue_flush_file
+    - ipv6: init the accept_queue's spinlocks in inet6_create
+    - net/mlx5: DR, Use the right GVMI number for drop action
+    - net/mlx5: DR, Align mlx5dv_dr API vport action with FW behavior
+    - net/mlx5: DR, Can't go to uplink vport on RX rule
+    - net/mlx5e: fix a double-free in arfs_create_groups
+    - net/mlx5e: fix a potential double-free in fs_any_create_groups
+    - overflow: Allow mixed type arguments
+    - netfilter: nft_limit: reject configurations that cause integer overflow
+    - netfilter: nf_tables: restrict anonymous set and map names to 16 bytes
+    - netfilter: nf_tables: validate NFPROTO_* family
+    - net: stmmac: Wait a bit for the reset to take effect
+    - net: mvpp2: clear BM pool before initialization
+    - selftests: netdevsim: fix the udp_tunnel_nic test
+    - fjes: fix memleaks in fjes_hw_setup
+    - net: fec: fix the unhandled context fault from smmu
+    - btrfs: fix infinite directory reads
+    - btrfs: set last dir index to the current last index when opening dir
+    - btrfs: refresh dir last index during a rewinddir(3) call
+    - btrfs: fix race between reading a directory and adding entries to it
+    - btrfs: avoid copying BTRFS_ROOT_SUBVOL_DEAD flag to snapshot of subvolume
+      being deleted
+    - btrfs: ref-verify: free ref cache before clearing mount opt
+    - btrfs: tree-checker: fix inline ref size in error messages
+    - btrfs: don't warn if discard range is not aligned to sector
+    - btrfs: defrag: reject unknown flags of btrfs_ioctl_defrag_range_args
+    - btrfs: don't abort filesystem when attempting to snapshot deleted subvolume
+    - rbd: don't move requests to the running list on errors
+    - exec: Fix error handling in begin_new_exec()
+    - wifi: iwlwifi: fix a memory corruption
+    - hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes
+    - netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress
+      basechain
+    - firmware: arm_scmi: Check mailbox/SMT channel for consistency
+    - xfs: read only mounts with fsopen mount API are busted
+    - gpiolib: acpi: Ignore touchpad wakeup on GPD G1619-04
+    - drm: Don't unref the same fb many times by mistake due to deadlock handling
+    - drm/bridge: nxp-ptn3460: fix i2c_master_send() error checking
+    - drm/tidss: Fix atomic_flush check
+    - drm/bridge: nxp-ptn3460: simplify some error checking
+    - PM: core: Remove unnecessary (void *) conversions
+    - PM: sleep: Fix possible deadlocks in core system-wide PM code
+    - bus: mhi: host: Rename "struct mhi_tre" to "struct mhi_ring_element"
+    - bus: mhi: host: Add alignment check for event ring read pointer
+    - fs/pipe: move check to pipe_has_watch_queue()
+    - pipe: wakeup wr_wait after setting max_usage
+    - ARM: dts: qcom: sdx55: fix USB wakeup interrupt types
+    - ARM: dts: samsung: exynos4210-i9100: Unconditionally enable LDO12
+    - ARM: dts: qcom: sdx55: fix pdc '#interrupt-cells'
+    - ARM: dts: qcom: sdx55: fix USB DP/DM HS PHY interrupts
+    - ARM: dts: qcom: sdx55: fix USB SS wakeup
+    - media: mtk-jpeg: Fix use after free bug due to error path handling in
+      mtk_jpeg_dec_device_run
+    - mm: use __pfn_to_section() instead of open coding it
+    - mm/sparsemem: fix race in accessing memory_section->usage
+    - PM / devfreq: Fix buffer overflow in trans_stat_show
+    - btrfs: add definition for EXTENT_TREE_V2
+    - ksmbd: fix global oob in ksmbd_nl_policy
+    - cpufreq: intel_pstate: Drop redundant intel_pstate_get_hwp_cap() call
+    - cpufreq: intel_pstate: Refine computation of P-state for given frequency
+    - drm: panel-simple: add missing bus flags for Tianma tm070jvhg[30/33]
+    - drm/exynos: fix accidental on-stack copy of exynos_drm_plane
+    - drm/exynos: gsc: minor fix for loop iteration in gsc_runtime_resume
+    - gpio: eic-sprd: Clear interrupt after set the interrupt type
+    - spi: bcm-qspi: fix SFDP BFPT read by usig mspi read
+    - mips: Call lose_fpu(0) before initializing fcr31 in mips_set_personality_nan
+    - tick/sched: Preserve number of idle sleeps across CPU hotplug events
+    - x86/entry/ia32: Ensure s32 is sign extended to s64
+    - powerpc/mm: Fix null-pointer dereference in pgtable_cache_add
+    - arm64: irq: set the correct node for VMAP stack
+    - drivers/perf: pmuv3: don't expose SW_INCR event in sysfs
+    - powerpc: Fix build error due to is_valid_bugaddr()
+    - powerpc/mm: Fix build failures due to arch_reserved_kernel_pages()
+    - powerpc/64s: Fix CONFIG_NUMA=n build due to create_section_mapping()
+    - x86/boot: Ignore NMIs during very early boot
+    - powerpc: pmd_move_must_withdraw() is only needed for
+      CONFIG_TRANSPARENT_HUGEPAGE
+    - powerpc/lib: Validate size for vector operations
+    - x86/mce: Mark fatal MCE's page as poison to avoid panic in the kdump kernel
+    - perf/core: Fix narrow startup race when creating the perf nr_addr_filters
+      sysfs file
+    - debugobjects: Stop accessing objects after releasing hash bucket lock
+    - regulator: core: Only increment use_count when enable_count changes
+    - audit: Send netlink ACK before setting connection in auditd_set
+    - ACPI: video: Add quirk for the Colorful X15 AT 23 Laptop
+    - PNP: ACPI: fix fortify warning
+    - ACPI: extlog: fix NULL pointer dereference check
+    - PM / devfreq: Synchronize devfreq_monitor_[start/stop]
+    - ACPI: APEI: set memory failure flags as MF_ACTION_REQUIRED on synchronous
+      events
+    - FS:JFS:UBSAN:array-index-out-of-bounds in dbAdjTree
+    - jfs: fix slab-out-of-bounds Read in dtSearch
+    - jfs: fix array-index-out-of-bounds in dbAdjTree
+    - pstore/ram: Fix crash when setting number of cpus to an odd number
+    - crypto: octeontx2 - Fix cptvf driver cleanup
+    - crypto: stm32/crc32 - fix parsing list of devices
+    - afs: fix the usage of read_seqbegin_or_lock() in afs_lookup_volume_rcu()
+    - afs: fix the usage of read_seqbegin_or_lock() in afs_find_server*()
+    - rxrpc_find_service_conn_rcu: fix the usage of read_seqbegin_or_lock()
+    - jfs: fix array-index-out-of-bounds in diNewExt
+    - arch: consolidate arch_irq_work_raise prototypes
+    - s390/ptrace: handle setting of fpc register correctly
+    - KVM: s390: fix setting of fpc register
+    - SUNRPC: Fix a suspicious RCU usage warning
+    - ecryptfs: Reject casefold directory inodes
+    - ext4: fix inconsistent between segment fstrim and full fstrim
+    - ext4: unify the type of flexbg_size to unsigned int
+    - ext4: remove unnecessary check from alloc_flex_gd()
+    - ext4: avoid online resizing failures due to oversized flex bg
+    - wifi: rt2x00: restart beacon queue when hardware reset
+    - selftests/bpf: satisfy compiler by having explicit return in btf test
+    - selftests/bpf: Fix pyperf180 compilation failure with clang18
+    - selftests/bpf: Fix issues in setup_classid_environment()
+    - scsi: lpfc: Fix possible file string name overflow when updating firmware
+    - PCI: Add no PM reset quirk for NVIDIA Spectrum devices
+    - bonding: return -ENOMEM instead of BUG in alb_upper_dev_walk
+    - scsi: arcmsr: Support new PCI device IDs 1883 and 1886
+    - ARM: dts: imx7d: Fix coresight funnel ports
+    - ARM: dts: imx7s: Fix lcdif compatible
+    - ARM: dts: imx7s: Fix nand-controller #size-cells
+    - wifi: ath9k: Fix potential array-index-out-of-bounds read in
+      ath9k_htc_txstatus()
+    - bpf: Add map and need_defer parameters to .map_fd_put_ptr()
+    - scsi: libfc: Don't schedule abort twice
+    - scsi: libfc: Fix up timeout error in fc_fcp_rec_error()
+    - bpf: Set uattr->batch.count as zero before batched update or deletion
+    - ARM: dts: rockchip: fix rk3036 hdmi ports node
+    - ARM: dts: imx25/27-eukrea: Fix RTC node name
+    - ARM: dts: imx: Use flash@0,0 pattern
+    - ARM: dts: imx27: Fix sram node
+    - ARM: dts: imx1: Fix sram node
+    - ionic: pass opcode to devcmd_wait
+    - block/rnbd-srv: Check for unlikely string overflow
+    - ARM: dts: imx25: Fix the iim compatible string
+    - ARM: dts: imx25/27: Pass timing0
+    - ARM: dts: imx27-apf27dev: Fix LED name
+    - ARM: dts: imx23-sansa: Use preferred i2c-gpios properties
+    - ARM: dts: imx23/28: Fix the DMA controller node name
+    - net: dsa: mv88e6xxx: Fix mv88e6352_serdes_get_stats error path
+    - block: prevent an integer overflow in bvec_try_merge_hw_page
+    - md: Whenassemble the array, consult the superblock of the freshest device
+    - arm64: dts: qcom: msm8996: Fix 'in-ports' is a required property
+    - arm64: dts: qcom: msm8998: Fix 'out-ports' is a required property
+    - wifi: rtl8xxxu: Add additional USB IDs for RTL8192EU devices
+    - libbpf: Fix NULL pointer dereference in bpf_object__collect_prog_relos
+    - ALSA: usb-audio: Add delay quirk for MOTU M Series 2nd revision
+    - wifi: rtlwifi: rtl8723{be,ae}: using calculate_bit_shift()
+    - wifi: cfg80211: free beacon_ies when overridden from hidden BSS
+    - Bluetooth: qca: Set both WIDEBAND_SPEECH and LE_STATES quirks for QCA2066
+    - Bluetooth: L2CAP: Fix possible multiple reject send
+    - bridge: cfm: fix enum typo in br_cc_ccm_tx_parse
+    - i40e: Fix VF disable behavior to block all traffic
+    - octeontx2-af: Fix max NPC MCAM entry check while validating ref_entry
+    - f2fs: fix to check return value of f2fs_reserve_new_block()
+    - ALSA: hda: Refer to correct stream index at loops
+    - ASoC: doc: Fix undefined SND_SOC_DAPM_NOPM argument
+    - fast_dput(): handle underflows gracefully
+    - RDMA/IPoIB: Fix error code return in ipoib_mcast_join
+    - drm/amd/display: Fix tiled display misalignment
+    - f2fs: fix write pointers on zoned device after roll forward
+    - drm/drm_file: fix use of uninitialized variable
+    - drm/framebuffer: Fix use of uninitialized variable
+    - drm/mipi-dsi: Fix detach call without attach
+    - media: stk1160: Fixed high volume of stk1160_dbg messages
+    - media: rockchip: rga: fix swizzling for RGB formats
+    - PCI: add INTEL_HDA_ARL to pci_ids.h
+    - ALSA: hda: Intel: add HDA_ARL PCI ID support
+    - ALSA: hda: intel-dspcfg: add filters for ARL-S and ARL
+    - media: rkisp1: Drop IRQF_SHARED
+    - f2fs: fix to tag gcing flag on page during block migration
+    - drm/exynos: Call drm_atomic_helper_shutdown() at shutdown/unbind time
+    - IB/ipoib: Fix mcast list locking
+    - media: ddbridge: fix an error code problem in ddb_probe
+    - media: i2c: imx335: Fix hblank min/max values
+    - drm/msm/dpu: Ratelimit framedone timeout msgs
+    - drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap
+    - clk: hi3620: Fix memory leak in hi3620_mmc_clk_init()
+    - clk: mmp: pxa168: Fix memory leak in pxa168_clk_init()
+    - watchdog: it87_wdt: Keep WDTCTRL bit 3 unmodified for IT8784/IT8786
+    - clk: imx: scu: Fix memory leak in __imx_clk_gpr_scu()
+    - clk: imx: clk-imx8qxp: fix LVDS bypass, pixel and phy clocks
+    - drm/amdgpu: Let KFD sync with VM fences
+    - drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
+    - ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140
+    - leds: trigger: panic: Don't register panic notifier if creating the trigger
+      failed
+    - um: Fix naming clash between UML and scheduler
+    - um: Don't use vfprintf() for os_info()
+    - um: net: Fix return type of uml_net_start_xmit()
+    - um: time-travel: fix time corruption
+    - i3c: master: cdns: Update maximum prescaler value for i2c clock
+    - xen/gntdev: Fix the abuse of underlying struct page in DMA-buf import
+    - mfd: ti_am335x_tscadc: Fix TI SoC dependencies
+    - [Config] updateconfigs for MFD_TI_AM335X_TSCADC
+    - mailbox: arm_mhuv2: Fix a bug for mhuv2_sender_interrupt
+    - PCI: Only override AMD USB controller if required
+    - PCI: switchtec: Fix stdev_release() crash after surprise hot remove
+    - perf cs-etm: Bump minimum OpenCSD version to ensure a bugfix is present
+    - usb: hub: Replace hardcoded quirk value with BIT() macro
+    - selftests/sgx: Fix linker script asserts
+    - tty: allow TIOCSLCKTRMIOS with CAP_CHECKPOINT_RESTORE
+    - fs/kernfs/dir: obey S_ISGID
+    - PCI: Fix 64GT/s effective data rate calculation
+    - PCI/AER: Decode Requester ID when no error info found
+    - libsubcmd: Fix memory leak in uniq()
+    - drm/amdkfd: Fix lock dependency warning
+    - virtio_net: Fix "‘%d’ directive writing between 1 and 11 bytes into a region
+      of size 10" warnings
+    - blk-mq: fix IO hang from sbitmap wakeup race
+    - ceph: fix deadlock or deadcode of misusing dget()
+    - drm/amd/powerplay: Fix kzalloc parameter 'ATOM_Tonga_PPM_Table' in
+      'get_platform_power_management_table()'
+    - drm/amdgpu: Release 'adev->pm.fw' before return in
+      'amdgpu_device_need_post()'
+    - drm/amdkfd: Fix 'node' NULL check in 'svm_range_get_range_boundaries()'
+    - perf: Fix the nr_addr_filters fix
+    - wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
+    - drm: using mul_u32_u32() requires linux/math64.h
+    - scsi: isci: Fix an error code problem in isci_io_request_build()
+    - scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler
+    - selftests: net: give more time for GRO aggregation
+    - ip6_tunnel: use dev_sw_netstats_rx_add()
+    - ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()
+    - tcp: add sanity checks to rx zerocopy
+    - ixgbe: Remove non-inclusive language
+    - ixgbe: Refactor returning internal error codes
+    - ixgbe: Refactor overtemp event handling
+    - ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550()
+    - ipv6: Ensure natural alignment of const ipv6 loopback and router addresses
+    - llc: call sock_orphan() at release time
+    - bridge: mcast: fix disabled snooping after long uptime
+    - netfilter: nf_tables: restrict tunnel object to NFPROTO_NETDEV
+    - netfilter: nf_log: replace BUG_ON by WARN_ON_ONCE when putting logger
+    - netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom
+      expectations
+    - net: ipv4: fix a memleak in ip_setup_cork
+    - af_unix: fix lockdep positive in sk_diag_dump_icons()
+    - SAUCE: Sync apparmor copy of af_unix.c
+    - selftests: net: fix available tunnels detection
+    - net: sysfs: Fix /sys/class/net/<iface> path
+    - arm64: irq: set the correct node for shadow call stack
+    - gve: Fix use-after-free vulnerability
+    - HID: apple: Add support for the 2021 Magic Keyboard
+    - HID: apple: Add 2021 magic keyboard FN key mapping
+    - bonding: remove print in bond_verify_device_path
+    - ASoC: codecs: lpass-wsa-macro: fix compander volume hack
+    - dmaengine: fsl-dpaa2-qdma: Fix the size of dma pools
+    - dmaengine: ti: k3-udma: Report short packet errors
+    - dmaengine: fsl-qdma: Fix a memory leak related to the status queue DMA
+    - dmaengine: fsl-qdma: Fix a memory leak related to the queue command DMA
+    - phy: renesas: rcar-gen3-usb2: Fix returning wrong error code
+    - dmaengine: fix is_slave_direction() return false when DMA_DEV_TO_DEV
+    - phy: ti: phy-omap-usb2: Fix NULL pointer dereference for SRP
+    - drm/msm/dp: return correct Colorimetry for DP_TEST_DYNAMIC_RANGE_CEA case
+    - net: stmmac: xgmac: fix handling of DPP safety error for DMA channels
+    - selftests: net: cut more slack for gro fwd tests.
+    - selftests: net: avoid just another constant wait
+    - tunnels: fix out of bounds access when building IPv6 PMTU error
+    - atm: idt77252: fix a memleak in open_card_ubr0
+    - octeontx2-pf: Fix a memleak otx2_sq_init
+    - hwmon: (aspeed-pwm-tacho) mutex for tach reading
+    - hwmon: (coretemp) Fix out-of-bounds memory access
+    - hwmon: (coretemp) Fix bogus core_id to attr name mapping
+    - inet: read sk->sk_family once in inet_recv_error()
+    - rxrpc: Fix response to PING RESPONSE ACKs to a dead call
+    - tipc: Check the bearer type before calling tipc_udp_nl_bearer_add()
+    - af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.
+    - ppp_async: limit MRU to 64K
+    - netfilter: nft_compat: reject unused compat flag
+    - netfilter: nft_compat: restrict match/target protocol to u16
+    - drm/amd/display: Fix multiple memory leaks reported by coverity
+    - drm/amd/display: Implement bounds check for stream encoder creation in
+      DCN301
+    - netfilter: nft_ct: reject direction for ct id
+    - netfilter: nft_set_pipapo: store index in scratch maps
+    - netfilter: nft_set_pipapo: add helper to release pcpu scratch area
+    - netfilter: nft_set_pipapo: remove scratch_aligned pointer
+    - fs/ntfs3: Fix an NULL dereference bug
+    - scsi: core: Move scsi_host_busy() out of host lock if it is for per-command
+    - blk-iocost: Fix an UBSAN shift-out-of-bounds warning
+    - drivers: lkdtm: fix clang -Wformat warning
+    - ALSA: usb-audio: Add a quirk for Yamaha YIT-W12TX transmitter
+    - USB: serial: qcserial: add new usb-id for Dell Wireless DW5826e
+    - USB: serial: option: add Fibocom FM101-GL variant
+    - USB: serial: cp210x: add ID for IMST iM871A-USB
+    - usb: dwc3: host: Set XHCI_SG_TRB_CACHE_SIZE_QUIRK
+    - usb: host: xhci-plat: Add support for XHCI_SG_TRB_CACHE_SIZE_QUIRK
+    - hrtimer: Report offline hrtimer enqueue
+    - Input: i8042 - fix strange behavior of touchpad on Clevo NS70PU
+    - Input: atkbd - skip ATKBD_CMD_SETLEDS when skipping ATKBD_CMD_GETID
+    - clocksource: Skip watchdog check for large watchdog intervals
+    - net: stmmac: xgmac: use #define for string constants
+    - net: stmmac: xgmac: fix a typo of register name in DPP safety handling
+    - btrfs: forbid creating subvol qgroups
+    - btrfs: forbid deleting live subvol qgroup
+    - btrfs: send: return EOPNOTSUPP on unknown flags
+    - of: unittest: Fix compile in the non-dynamic case
+    - wifi: iwlwifi: Fix some error codes
+    - net: openvswitch: limit the number of recursions from action sets
+    - spi: ppc4xx: Drop write-only variable
+    - ASoC: rt5645: Fix deadlock in rt5645_jack_detect_work()
+    - net: sysfs: Fix /sys/class/net/<iface> path for statistics
+    - MIPS: Add 'memory' clobber to csum_ipv6_magic() inline assembler
+    - i40e: Fix waiting for queues of all VSIs to be disabled
+    - scs: add CONFIG_MMU dependency for vfree_atomic()
+    - tracing/trigger: Fix to return error if failed to alloc snapshot
+    - mm/writeback: fix possible divide-by-zero in wb_dirty_limits(), again
+    - scsi: storvsc: Fix ring buffer size calculation
+    - ALSA: hda/realtek: Fix the external mic not being recognised for Acer Swift
+      1 SF114-32
+    - ALSA: hda/realtek: Enable Mute LED on HP Laptop 14-fq0xxx
+    - HID: i2c-hid-of: fix NULL-deref on failed power up
+    - HID: wacom: generic: Avoid reporting a serial of '0' to userspace
+    - HID: wacom: Do not register input devices until after hid_hw_start
+    - iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP
+    - usb: ucsi_acpi: Fix command completion handling
+    - USB: hub: check for alternate port before enabling A_ALT_HNP_SUPPORT
+    - usb: f_mass_storage: forbid async queue when shutdown happen
+    - usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend
+    - media: ir_toy: fix a memleak in irtoy_tx
+    - powerpc/kasan: Fix addr error caused by page alignment
+    - i2c: i801: Remove i801_set_block_buffer_mode
+    - i2c: i801: Fix block process call transactions
+    - modpost: trim leading spaces when processing source files list
+    - mptcp: fix data re-injection from stale subflow
+    - scsi: Revert "scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock"
+    - Revert "drm/amd: flush any delayed gfxoff on suspend entry"
+    - firewire: core: correct documentation of fw_csr_string() kernel API
+    - kbuild: Fix changing ELF file type for output of gen_btf for big endian
+    - nfc: nci: free rx_data_reassembly skb on NCI device cleanup
+    - net: hsr: remove WARN_ONCE() in send_hsr_supervision_frame()
+    - xen-netback: properly sync TX responses
+    - ALSA: hda/realtek: Enable headset mic on Vaio VJFE-ADL
+    - ASoC: codecs: wcd938x: handle deferred probe
+    - binder: signal epoll threads of self-work
+    - misc: fastrpc: Mark all sessions as invalid in cb_remove
+    - ext4: fix double-free of blocks due to wrong extents moved_len
+    - tracing: Fix wasted memory in saved_cmdlines logic
+    - staging: iio: ad5933: fix type mismatch regression
+    - iio: magnetometer: rm3100: add boundary check for the value read from
+      RM3100_REG_TMRC
+    - iio: core: fix memleak in iio_device_register_sysfs
+    - iio: accel: bma400: Fix a compilation problem
+    - media: rc: bpf attach/detach requires write permission
+    - drm/prime: Support page array >= 4GB
+    - hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove
+    - ring-buffer: Clean ring_buffer_poll_wait() error return
+    - serial: max310x: set default value when reading clock ready bit
+    - serial: max310x: improve crystal stable clock detection
+    - serial: max310x: fail probe if clock crystal is unstable
+    - powerpc/64: Set task pt_regs->link to the LR value on scv entry
+    - x86/Kconfig: Transmeta Crusoe is CPU family 5, not 6
+    - x86/mm/ident_map: Use gbpages only where full GB page should be mapped.
+    - mmc: slot-gpio: Allow non-sleeping GPIO ro
+    - ALSA: hda/conexant: Add quirk for SWS JS201D
+    - nilfs2: fix data corruption in dsync block recovery for small block sizes
+    - nilfs2: fix hang in nilfs_lookup_dirty_data_buffers()
+    - crypto: ccp - Fix null pointer dereference in __sev_platform_shutdown_locked
+    - nfp: use correct macro for LengthSelect in BAR config
+    - nfp: flower: prevent re-adding mac index for bonded port
+    - wifi: mac80211: reload info pointer in ieee80211_tx_dequeue()
+    - irqchip/irq-brcmstb-l2: Add write memory barrier before exit
+    - irqchip/gic-v3-its: Fix GICv4.1 VPE affinity update
+    - net: ethernet: ti: cpsw: enable mac_managed_pm to fix mdio
+    - s390/qeth: Fix potential loss of L3-IP@ in case of network issues
+    - net: ethernet: ti: cpsw_new: enable mac_managed_pm to fix mdio
+    - ceph: prevent use-after-free in encode_cap_msg()
+    - mm: hugetlb pages should not be reserved by shmat() if SHM_NORESERVE
+    - of: property: fix typo in io-channels
+    - can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
+    - can: j1939: Fix UAF in j1939_sk_match_filter during
+      setsockopt(SO_J1939_FILTER)
+    - pmdomain: core: Move the unused cleanup to a _sync initcall
+    - tracing: Inform kmemleak of saved_cmdlines allocation
+    - af_unix: Fix task hung while purging oob_skb in GC.
+    - dma-buf: add dma_fence_timestamp helper
+    - bus: moxtet: Add spi device table
+    - crypto: lib/mpi - Fix unexpected pointer access in mpi_ec_init
+    - usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
+    - usb: dwc3: ep0: Don't prepare beyond Setup stage
+    - usb: dwc3: gadget: Only End Transfer for ep0 data phase
+    - usb: dwc3: gadget: Delay issuing End Transfer
+    - usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
+    - usb: dwc3: gadget: Force sending delayed status during soft disconnect
+    - usb: dwc3: gadget: Submit endxfer command if delayed during disconnect
+    - usb: dwc3: gadget: Stall and restart EP0 if host is unresponsive
+    - usb: dwc3: gadget: Refactor EP0 forced stall/restart into a separate API
+    - usb: dwc3: gadget: Handle EP0 request dequeuing properly
+    - usb: dwc3: gadget: Queue PM runtime idle on disconnect event
+    - serial: 8250_exar: Fill in rs485_supported
+    - serial: 8250_exar: Set missing rs485_supported flag
+    - fbdev/defio: Early-out if page is already enlisted
+    - fbdev: Don't sort deferred-I/O pages by default
+    - fbdev: defio: fix the pagelist corruption
+    - fbdev: Track deferred-I/O pages in pageref struct
+    - fbdev: Rename pagelist to pagereflist for deferred I/O
+    - fbdev: Fix invalid page access after closing deferred I/O devices
+    - fbdev: Fix incorrect page mapping clearance at fb_deferred_io_release()
+    - fbdev: flush deferred IO before closing
+    - scripts/decode_stacktrace.sh: support old bash version
+    - scripts: decode_stacktrace: demangle Rust symbols
+    - scripts/decode_stacktrace.sh: optionally use LLVM utilities
+    - netfilter: ipset: fix performance regression in swap operation
+    - hrtimer: Ignore slack time for RT tasks in schedule_hrtimeout_range()
+    - net: prevent mss overflow in skb_segment()
+    - netfilter: ipset: Missing gc cancellations fixed
+    - sched/membarrier: reduce the ability to hammer on sys_membarrier
+    - nilfs2: fix potential bug in end_buffer_async_write
+    - nilfs2: replace WARN_ONs for invalid DAT metadata block requests
+    - arm64: Subscribe Microsoft Azure Cobalt 100 to ARM Neoverse N2 errata
+    - PM: runtime: Have devm_pm_runtime_enable() handle
+      pm_runtime_dont_use_autosuspend()
+    - drm/msm/dsi: Enable runtime PM
+    - net: bcmgenet: Fix EEE implementation
+    - fs/ntfs3: Add null pointer checks
+    - staging: fbtft: core: set smem_len before fb_deferred_io_init call
+    - usb: dwc3: gadget: Don't delay End Transfer on delayed_status
+    - usb: dwc3: gadget: Execute gadget stop after halting the controller
+    - media: Revert "media: rkisp1: Drop IRQF_SHARED"
+    - usb: dwc3: gadget: Ignore End Transfer delay on teardown
+    - Linux 5.15.149
+  * Fix headphone mic detection issue on ALC897 (LP: #2056418)
+    - ALSA: hda/realtek - Fix headset Mic no show at resume back for Lenovo ALC897
+      platform
+  * CVE-2023-6039
+    - timers: Replace BUG_ON()s
+  * Problems with HVCS and hotplugging (LP: #2056373)
+    - hvcs: Fix hvcs port reference counting
+    - hvcs: Use dev_groups to manage hvcs device attributes
+    - hvcs: Use driver groups to manage driver attributes
+    - hvcs: Get reference to tty in remove
+    - hvcs: Use vhangup in hotplug remove
+    - hvcs: Synchronize hotplug remove with port free
+  * KVM: arm64: softlockups in stage2_apply_range (LP: #2056227)
+    - KVM: arm64: Work out supported block level at compile time
+    - KVM: arm64: Limit stage2_apply_range() batch size to largest block
+
+  [ Ubuntu: 5.15.0-105.115 ]
+
+  * jammy/linux: 5.15.0-105.115 -proposed tracker (LP: #2061372)
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014) // CIFS
+    stopped working/is unstable with kernel update to 5.15.0-102.112
+    (LP: #2060780)
+    - smb3: Replace smb2pdu 1-element arrays with flex-arrays
+
+  [ Ubuntu: 5.15.0-103.113 ]
+
+  * jammy/linux: 5.15.0-103.113 -proposed tracker (LP: #2059683)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop getabis data
+  * Remove getabis scripts (LP: #2059143)
+    - [Packaging] Remove getabis
+  * CVE-2023-24023
+    - Bluetooth: Add more enc key size check
+  * CVE-2023-52600
+    - jfs: fix uaf in jfs_evict_inode
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014) //
+    CVE-2023-52603
+    - UBSAN: array-index-out-of-bounds in dtSplitRoot
+  * CVE-2024-26581
+    - netfilter: nft_set_rbtree: skip end interval element from gc
+
+  [ Ubuntu: 5.15.0-102.112 ]
+
+  * jammy/linux: 5.15.0-102.112 -proposed tracker (LP: #2055632)
+  * Drop ABI checks from kernel build (LP: #2055686)
+    - [Packaging] Remove in-tree abi checks
+    - [Packaging] Drop abi checks from final-checks
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop ABI data
+    - [Packaging] update annotations scripts
+    - debian.master/dkms-versions -- update from kernel-versions (main/2024.03.04)
+  * block/loop: No longer allows to create partitions (LP: #2056143)
+    - block, loop: support partitions without scanning
+  * Cranky update-dkms-versions rollout (LP: #2055685)
+    - [Packaging] remove update-dkms-versions
+    - Move debian/dkms-versions to debian.master/dkms-versions
+    - [Packaging] Replace debian/dkms-versions with $(DEBIAN)/dkms-versions
+    - [Packaging] remove update-version-dkms
+  * linux: please move erofs.ko (CONFIG_EROFS for EROFS support) from linux-
+    modules-extra to linux-modules (LP: #2054809)
+    - UBUNTU [Packaging]: Include erofs in linux-modules instead of linux-modules-
+      extra
+  * linux-tools-common: man page of usbip[d] is misplaced (LP: #2054094)
+    - [Packaging] rules: Put usbip manpages in the correct directory
+  * CVE-2024-23851
+    - dm ioctl: log an error if the ioctl structure is corrupted
+    - dm: limit the number of targets and parameter size area
+  * CVE-2024-23850
+    - btrfs: do not ASSERT() if the newly created subvolume already got read
+  * x86: performance: tsc: Extend watchdog check exemption to 4-Sockets platform
+    (LP: #2054699)
+    - x86/tsc: Extend watchdog check exemption to 4-Sockets platform
+  * linux: please move dmi-sysfs.ko (CONFIG_DMI_SYSFS for SMBIOS support) from
+    linux-modules-extra to linux-modules (LP: #2045561)
+    - [Packaging] Move dmi-sysfs.ko into linux-modules
+  * Fix bpf selftests build failure after v5.15.139 update (LP: #2054567)
+    - Revert "selftests/bpf: Test tail call counting with bpf2bpf and data on
+      stack"
+  * Jammy update: v5.15.148 upstream stable release (LP: #2055145)
+    - f2fs: explicitly null-terminate the xattr list
+    - pinctrl: lochnagar: Don't build on MIPS
+    - ALSA: hda - Fix speaker and headset mic pin config for CHUWI CoreBook XPro
+    - mptcp: fix uninit-value in mptcp_incoming_options
+    - wifi: cfg80211: lock wiphy mutex for rfkill poll
+    - debugfs: fix automount d_fsdata usage
+    - drm/amdgpu: Fix cat debugfs amdgpu_regs_didt causes kernel null pointer
+    - nvme-core: check for too small lba shift
+    - ASoC: wm8974: Correct boost mixer inputs
+    - ASoC: Intel: Skylake: Fix mem leak in few functions
+    - ASoC: nau8822: Fix incorrect type in assignment and cast to restricted
+      __be16
+    - ASoC: Intel: Skylake: mem leak in skl register function
+    - ASoC: cs43130: Fix the position of const qualifier
+    - ASoC: cs43130: Fix incorrect frame delay configuration
+    - ASoC: rt5650: add mutex to avoid the jack detection failure
+    - nouveau/tu102: flush all pdbs on vmm flush
+    - net/tg3: fix race condition in tg3_reset_task()
+    - ASoC: da7219: Support low DC impedance headset
+    - ASoC: ops: add correct range check for limiting volume
+    - nvme: introduce helper function to get ctrl state
+    - drm/amdgpu: Add NULL checks for function pointers
+    - drm/exynos: fix a potential error pointer dereference
+    - drm/exynos: fix a wrong error checking
+    - hwmon: (corsair-psu) Fix probe when built-in
+    - clk: rockchip: rk3128: Fix HCLK_OTG gate register
+    - jbd2: correct the printing of write_flags in jbd2_write_superblock()
+    - drm/crtc: Fix uninit-value bug in drm_mode_setcrtc
+    - neighbour: Don't let neigh_forced_gc() disable preemption for long
+    - platform/x86: intel-vbtn: Fix missing tablet-mode-switch events
+    - jbd2: fix soft lockup in journal_finish_inode_data_buffers()
+    - tracing: Have large events show up as '[LINE TOO BIG]' instead of nothing
+    - tracing: Add size check when printing trace_marker output
+    - stmmac: dwmac-loongson: drop useless check for compatible fallback
+    - MIPS: dts: loongson: drop incorrect dwmac fallback compatible
+    - tracing: Fix uaf issue when open the hist or hist_debug file
+    - ring-buffer: Do not record in NMI if the arch does not support cmpxchg in
+      NMI
+    - reset: hisilicon: hi6220: fix Wvoid-pointer-to-enum-cast warning
+    - Input: atkbd - skip ATKBD_CMD_GETID in translated mode
+    - Input: i8042 - add nomux quirk for Acer P459-G2-M
+    - s390/scm: fix virtual vs physical address confusion
+    - ARC: fix spare error
+    - wifi: iwlwifi: pcie: avoid a NULL pointer dereference
+    - Input: xpad - add Razer Wolverine V2 support
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Medion Lifetab S10346
+    - i2c: rk3x: fix potential spinlock recursion on poll
+    - net: qrtr: ns: Return 0 if server port is not present
+    - ARM: sun9i: smp: fix return code check of of_property_match_string
+    - drm/crtc: fix uninitialized variable use
+    - ACPI: resource: Add another DMI match for the TongFang GMxXGxx
+    - Revert "ASoC: atmel: Remove system clock tree configuration for
+      at91sam9g20ek"
+    - bpf: Add --skip_encoding_btf_inconsistent_proto, --btf_gen_optimized to
+      pahole flags for v1.25
+    - kprobes: Fix to handle forcibly unoptimized kprobes on freeing_list
+    - Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"
+    - binder: use EPOLLERR from eventpoll.h
+    - binder: fix use-after-free in shinker's callback
+    - binder: fix trivial typo of binder_free_buf_locked()
+    - binder: fix comment on binder_alloc_new_buf() return value
+    - uio: Fix use-after-free in uio_open
+    - parport: parport_serial: Add Brainboxes BAR details
+    - parport: parport_serial: Add Brainboxes device IDs and geometry
+    - leds: ledtrig-tty: Free allocated ttyname buffer on deactivate
+    - PCI: Add ACS quirk for more Zhaoxin Root Ports
+    - coresight: etm4x: Fix width of CCITMIN field
+    - x86/lib: Fix overflow when counting digits
+    - EDAC/thunderx: Fix possible out-of-bounds string access
+    - powerpc: Mark .opd section read-only
+    - powerpc/toc: Future proof kernel toc
+    - powerpc: remove checks for binutils older than 2.25
+    - powerpc: add crtsavres.o to always-y instead of extra-y
+    - powerpc/44x: select I2C for CURRITUCK
+    - powerpc/pseries/memhp: Fix access beyond end of drmem array
+    - selftests/powerpc: Fix error handling in FPU/VMX preemption tests
+    - powerpc/powernv: Add a null pointer check to scom_debug_init_one()
+    - powerpc/powernv: Add a null pointer check in opal_event_init()
+    - powerpc/powernv: Add a null pointer check in opal_powercap_init()
+    - powerpc/imc-pmu: Add a null pointer check in update_events_in_group()
+    - spi: spi-zynqmp-gqspi: fix driver kconfig dependencies
+    - mtd: rawnand: Increment IFC_TIMEOUT_MSECS for nand controller response
+    - ACPI: video: check for error while searching for backlight device parent
+    - ACPI: LPIT: Avoid u32 multiplication overflow
+    - of: property: define of_property_read_u{8,16,32,64}_array() unconditionally
+    - of: Add of_property_present() helper
+    - cpufreq: Use of_property_present() for testing DT property presence
+    - cpufreq: scmi: process the result of devm_of_clk_add_hw_provider()
+    - calipso: fix memory leak in netlbl_calipso_add_pass()
+    - efivarfs: force RO when remounting if SetVariable is not supported
+    - spi: sh-msiof: Enforce fixed DTDL for R-Car H3
+    - ACPI: LPSS: Fix the fractional clock divider flags
+    - ACPI: extlog: Clear Extended Error Log status when RAS_CEC handled the error
+    - kunit: debugfs: Fix unchecked dereference in debugfs_print_results()
+    - mtd: Fix gluebi NULL pointer dereference caused by ftl notifier
+    - selinux: Fix error priority for bind with AF_UNSPEC on PF_INET6 socket
+    - crypto: virtio - Handle dataq logic with tasklet
+    - crypto: sa2ul - Return crypto_aead_setkey to transfer the error
+    - crypto: ccp - fix memleak in ccp_init_dm_workarea
+    - crypto: af_alg - Disallow multiple in-flight AIO requests
+    - crypto: sahara - remove FLAGS_NEW_KEY logic
+    - crypto: sahara - fix cbc selftest failure
+    - crypto: sahara - fix ahash selftest failure
+    - crypto: sahara - fix processing requests with cryptlen < sg->length
+    - crypto: sahara - fix error handling in sahara_hw_descriptor_create()
+    - pstore: ram_core: fix possible overflow in persistent_ram_init_ecc()
+    - fs: indicate request originates from old mount API
+    - gfs2: Fix kernel NULL pointer dereference in gfs2_rgrp_dump
+    - crypto: virtio - Wait for tasklet to complete on device remove
+    - crypto: sahara - avoid skcipher fallback code duplication
+    - crypto: sahara - handle zero-length aes requests
+    - crypto: sahara - fix ahash reqsize
+    - crypto: sahara - fix wait_for_completion_timeout() error handling
+    - crypto: sahara - improve error handling in sahara_sha_process()
+    - crypto: sahara - fix processing hash requests with req->nbytes < sg->length
+    - crypto: sahara - do not resize req->src when doing hash operations
+    - crypto: scomp - fix req->dst buffer overflow
+    - blocklayoutdriver: Fix reference leak of pnfs_device_node
+    - NFSv4.1/pnfs: Ensure we handle the error NFS4ERR_RETURNCONFLICT
+    - wifi: rtw88: fix RX filter in FIF_ALLMULTI flag
+    - bpf, lpm: Fix check prefixlen before walking trie
+    - bpf: Add crosstask check to __bpf_get_stack
+    - wifi: ath11k: Defer on rproc_get failure
+    - wifi: libertas: stop selecting wext
+    - ARM: dts: qcom: apq8064: correct XOADC register address
+    - net/ncsi: Fix netlink major/minor version numbers
+    - firmware: ti_sci: Fix an off-by-one in ti_sci_debugfs_create()
+    - firmware: meson_sm: populate platform devices from sm device tree data
+    - wifi: rtlwifi: rtl8821ae: phy: fix an undefined bitwise shift behavior
+    - arm64: dts: ti: k3-am65-main: Fix DSS irq trigger type
+    - bpf: enforce precision of R0 on callback return
+    - ARM: dts: qcom: sdx65: correct SPMI node name
+    - arm64: dts: qcom: sc7180: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sc7280: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sdm845: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sm8150: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sm8250: Make watchdog bark interrupt edge triggered
+    - bpf: fix check for attempt to corrupt spilled pointer
+    - scsi: fnic: Return error if vmalloc() failed
+    - arm64: dts: qcom: qrb5165-rb5: correct LED panic indicator
+    - arm64: dts: qcom: sdm845-db845c: correct LED panic indicator
+    - arm64: dts: qcom: sc7280: fix usb_2 wakeup interrupt types
+    - bpf: Fix verification of indirect var-off stack access
+    - block: Set memalloc_noio to false on device_add_disk() error path
+    - scsi: hisi_sas: Rename HISI_SAS_{RESET -> RESETTING}_BIT
+    - scsi: hisi_sas: Prevent parallel FLR and controller reset
+    - scsi: hisi_sas: Replace with standard error code return value
+    - scsi: hisi_sas: Rollback some operations if FLR failed
+    - scsi: hisi_sas: Correct the number of global debugfs registers
+    - selftests/net: fix grep checking for fib_nexthop_multiprefix
+    - virtio/vsock: fix logic which reduces credit update messages
+    - dma-mapping: Add dma_release_coherent_memory to DMA API
+    - dma-mapping: clear dev->dma_mem to NULL after freeing it
+    - soc: qcom: llcc: Fix dis_cap_alloc and retain_on_pc configuration
+    - arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
+    - block: add check of 'minors' and 'first_minor' in device_add_disk()
+    - arm64: dts: qcom: sc7280: Mark SDHCI hosts as cache-coherent
+    - wifi: rtlwifi: add calculate_bit_shift()
+    - wifi: rtlwifi: rtl8188ee: phy: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192c: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192cu: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192ce: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192de: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192ee: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192se: using calculate_bit_shift()
+    - wifi: iwlwifi: mvm: set siso/mimo chains to 1 in FW SMPS request
+    - wifi: iwlwifi: mvm: send TX path flush in rfkill
+    - netfilter: nf_tables: mark newset as dead on transaction abort
+    - Bluetooth: Fix bogus check for re-auth no supported with non-ssp
+    - Bluetooth: btmtkuart: fix recv_buf() return value
+    - block: make BLK_DEF_MAX_SECTORS unsigned
+    - null_blk: don't cap max_hw_sectors to BLK_DEF_MAX_SECTORS
+    - net/sched: act_ct: fix skb leak and crash on ooo frags
+    - mlxbf_gige: Fix intermittent no ip issue
+    - net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
+    - mlxbf_gige: Enable the GigE port in mlxbf_gige_open
+    - ip6_tunnel: fix NEXTHDR_FRAGMENT handling in ip6_tnl_parse_tlv_enc_lim()
+    - ARM: davinci: always select CONFIG_CPU_ARM926T
+    - Revert "drm/tidss: Annotate dma-fence critical section in commit path"
+    - Revert "drm/omapdrm: Annotate dma-fence critical section in commit path"
+    - RDMA/usnic: Silence uninitialized symbol smatch warnings
+    - RDMA/hns: Fix inappropriate err code for unsupported operations
+    - drm/panel-elida-kd35t133: hold panel in reset for unprepare
+    - drm/nouveau/fence:: fix warning directly dereferencing a rcu pointer
+    - drm/bridge: tpd12s015: Drop buggy __exit annotation for remove function
+    - drm/tilcdc: Fix irq free on unload
+    - media: pvrusb2: fix use after free on context disconnection
+    - drm/bridge: Fix typo in post_disable() description
+    - f2fs: fix to avoid dirent corruption
+    - drm/radeon/r600_cs: Fix possible int overflows in r600_cs_check_reg()
+    - drm/radeon/r100: Fix integer overflow issues in r100_cs_track_check()
+    - drm/radeon: check return value of radeon_ring_lock()
+    - ASoC: cs35l33: Fix GPIO name and drop legacy include
+    - ASoC: cs35l34: Fix GPIO name and drop legacy include
+    - drm/msm/mdp4: flush vblank event on disable
+    - drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks
+    - drm/drv: propagate errors from drm_modeset_register_all()
+    - drm/radeon: check the alloc_workqueue return value in radeon_crtc_init()
+    - drm/radeon/dpm: fix a memleak in sumo_parse_power_table
+    - drm/radeon/trinity_dpm: fix a memleak in trinity_parse_power_table
+    - drm/bridge: cdns-mhdp8546: Fix use of uninitialized variable
+    - drm/bridge: tc358767: Fix return value on error case
+    - media: cx231xx: fix a memleak in cx231xx_init_isoc
+    - clk: qcom: gpucc-sm8150: Update the gpu_cc_pll1 config
+    - media: rkisp1: Disable runtime PM in probe error path
+    - f2fs: fix to check compress file in f2fs_move_file_range()
+    - f2fs: fix to update iostat correctly in f2fs_filemap_fault()
+    - f2fs: fix the f2fs_file_write_iter tracepoint
+    - media: dvbdev: drop refcount on error path in dvb_device_open()
+    - media: dvb-frontends: m88ds3103: Fix a memory leak in an error handling path
+      of m88ds3103_probe()
+    - drm/amdgpu/debugfs: fix error code when smc register accessors are NULL
+    - drm/amd/pm: fix a double-free in si_dpm_init
+    - drivers/amd/pm: fix a use-after-free in kv_parse_power_table
+    - gpu/drm/radeon: fix two memleaks in radeon_vm_init
+    - dt-bindings: clock: Update the videocc resets for sm8150
+    - clk: qcom: videocc-sm8150: Update the videocc resets
+    - clk: qcom: videocc-sm8150: Add missing PLL config property
+    - drivers: clk: zynqmp: calculate closest mux rate
+    - clk: zynqmp: make bestdiv unsigned
+    - clk: zynqmp: Add a check for NULL pointer
+    - drivers: clk: zynqmp: update divider round rate logic
+    - watchdog: set cdev owner before adding
+    - watchdog/hpwdt: Only claim UNKNOWN NMI if from iLO
+    - watchdog: bcm2835_wdt: Fix WDIOC_SETTIMEOUT handling
+    - watchdog: rti_wdt: Drop runtime pm reference count when watchdog is unused
+    - clk: si5341: fix an error code problem in si5341_output_clk_set_rate
+    - clk: asm9260: use parent index to link the reference clock
+    - clk: fixed-rate: add devm_clk_hw_register_fixed_rate
+    - clk: fixed-rate: fix clk_hw_register_fixed_rate_with_accuracy_parent_hw
+    - pwm: stm32: Use regmap_clear_bits and regmap_set_bits where applicable
+    - pwm: stm32: Use hweight32 in stm32_pwm_detect_channels
+    - pwm: stm32: Fix enable count for clk in .probe()
+    - ASoC: rt5645: Drop double EF20 entry from dmi_platform_data[]
+    - ALSA: scarlett2: Add missing error check to scarlett2_config_save()
+    - ALSA: scarlett2: Add missing error check to scarlett2_usb_set_config()
+    - ALSA: scarlett2: Allow passing any output to line_out_remap()
+    - ALSA: scarlett2: Add missing error checks to *_ctl_get()
+    - ALSA: scarlett2: Add clamp() in scarlett2_mixer_ctl_put()
+    - mmc: sdhci_am654: Fix TI SoC dependencies
+    - [Config] update annotations for CONFIG_MMC_SDHCI_AM654
+    - [Config] remove sdhci_am654 module for armhf/ppc64el
+    - mmc: sdhci_omap: Fix TI SoC dependencies
+    - [Config] update annotations for CONFIG_MMC_SDHCI_OMAP
+    - [Config] remove sdhci-omap module for arm64/ppc64el
+    - IB/iser: Prevent invalidating wrong MR
+    - drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
+    - ksmbd: validate the zero field of packet header
+    - of: Fix double free in of_parse_phandle_with_args_map
+    - of: unittest: Fix of_count_phandle_with_args() expected value message
+    - selftests/bpf: Add assert for user stacks in test_task_stack
+    - binder: fix async space check for 0-sized buffers
+    - binder: fix unused alloc->free_async_space
+    - Input: atkbd - use ab83 as id when skipping the getid command
+    - dma-mapping: Fix build error unused-value
+    - virtio-crypto: fix memory leak in virtio_crypto_alg_skcipher_close_session()
+    - binder: fix race between mmput() and do_exit()
+    - tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
+    - usb: phy: mxs: remove CONFIG_USB_OTG condition for mxs_phy_is_otg_host()
+    - usb: dwc: ep0: Update request status in dwc3_ep0_stall_restart
+    - Revert "usb: dwc3: Soft reset phy on probe for host"
+    - Revert "usb: dwc3: don't reset device side if dwc3 was configured as host-
+      only"
+    - usb: chipidea: wait controller resume finished for wakeup irq
+    - usb: cdns3: fix uvc failure work since sg support enabled
+    - usb: cdns3: fix iso transfer error when mult is not zero
+    - usb: cdns3: Fix uvc fail when DMA cross 4k boundery since sg enabled
+    - Revert "usb: typec: class: fix typec_altmode_put_partner to put plugs"
+    - usb: typec: class: fix typec_altmode_put_partner to put plugs
+    - usb: mon: Fix atomicity violation in mon_bin_vma_fault
+    - serial: imx: Ensure that imx_uart_rs485_config() is called with enabled
+      clock
+    - ALSA: oxygen: Fix right channel of capture volume mixer
+    - ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx
+    - fbdev: flush deferred work in fb_deferred_io_fsync()
+    - scsi: mpi3mr: Refresh sdev queue depth after controller reset
+    - block: add check that partition length needs to be aligned with block size
+    - pwm: jz4740: Don't use dev_err_probe() in .request()
+    - io_uring/rw: ensure io->bytes_done is always initialized
+    - rootfs: Fix support for rootfstype= when root= is given
+    - Bluetooth: Fix atomicity violation in {min,max}_key_size_set
+    - bpf: Fix re-attachment branch in bpf_tracing_prog_attach
+    - iommu/arm-smmu-qcom: Add missing GMU entry to match table
+    - wifi: mt76: fix broken precal loading from MTD for mt7915
+    - wifi: rtlwifi: Remove bogus and dangerous ASPM disable/enable code
+    - wifi: rtlwifi: Convert LNKCTL change to PCIe cap RMW accessors
+    - wifi: mwifiex: configure BSSID consistently when starting AP
+    - PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support
+    - PCI: mediatek: Clear interrupt status before dispatching handler
+    - x86/kvm: Do not try to disable kvmclock if it was not enabled
+    - KVM: arm64: vgic-v4: Restore pending state on host userspace write
+    - KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cache
+    - iio: adc: ad7091r: Pass iio_dev to event handler
+    - HID: wacom: Correct behavior when processing some confidence == false
+      touches
+    - serial: sc16is7xx: add check for unsupported SPI modes during probe
+    - serial: sc16is7xx: set safe default SPI clock frequency
+    - iommu/dma: Trace bounce buffer usage when mapping buffers
+    - ARM: 9330/1: davinci: also select PINCTRL
+    - mfd: syscon: Fix null pointer dereference in of_syscon_register()
+    - leds: aw2013: Select missing dependency REGMAP_I2C
+    - mfd: intel-lpss: Fix the fractional clock divider flags
+    - mips: dmi: Fix early remap on MIPS32
+    - mips: Fix incorrect max_low_pfn adjustment
+    - riscv: Check if the code to patch lies in the exit section
+    - riscv: Fix module_alloc() that did not reset the linear mapping permissions
+    - MIPS: Alchemy: Fix an out-of-bound access in db1200_dev_setup()
+    - MIPS: Alchemy: Fix an out-of-bound access in db1550_dev_setup()
+    - power: supply: cw2015: correct time_to_empty units in sysfs
+    - power: supply: bq256xx: fix some problem in bq256xx_hw_init
+    - serial: 8250: omap: Don't skip resource freeing if
+      pm_runtime_resume_and_get() failed
+    - libapi: Add missing linux/types.h header to get the __u64 type on io.h
+    - software node: Let args be NULL in software_node_get_reference_args
+    - serial: imx: fix tx statemachine deadlock
+    - selftests/sgx: Fix uninitialized pointer dereference in error path
+    - selftests/sgx: Skip non X86_64 platform
+    - iio: adc: ad9467: Benefit from devm_clk_get_enabled() to simplify
+    - iio: adc: ad9467: fix reset gpio handling
+    - iio: adc: ad9467: don't ignore error codes
+    - iio: adc: ad9467: fix scale setting
+    - perf genelf: Set ELF program header addresses properly
+    - tty: change tty_write_lock()'s ndelay parameter to bool
+    - tty: early return from send_break() on TTY_DRIVER_HARDWARE_BREAK
+    - tty: don't check for signal_pending() in send_break()
+    - tty: use 'if' in send_break() instead of 'goto'
+    - usb: cdc-acm: return correct error code on unsupported break
+    - nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length
+    - nvmet-tcp: fix a crash in nvmet_req_complete()
+    - perf env: Avoid recursively taking env->bpf_progs.lock
+    - apparmor: avoid crash when parsed profile name is empty
+    - usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
+    - serial: imx: Correct clock error message in function probe()
+    - nvmet: re-fix tracing strncpy() warning
+    - nvmet-tcp: Fix the H2C expected PDU len calculation
+    - PCI: keystone: Fix race condition when initializing PHYs
+    - s390/pci: fix max size calculation in zpci_memcpy_toio()
+    - net: qualcomm: rmnet: fix global oob in rmnet_policy
+    - net: ethernet: ti: am65-cpsw: Fix max mtu to fit ethernet frames
+    - net: phy: micrel: populate .soft_reset for KSZ9131
+    - mptcp: mptcp_parse_option() fix for MPTCPOPT_MP_JOIN
+    - mptcp: drop unused sk in mptcp_get_options
+    - mptcp: strict validation before using mp_opt->hmac
+    - mptcp: use OPTION_MPTCP_MPJ_SYNACK in subflow_finish_connect()
+    - mptcp: use OPTION_MPTCP_MPJ_SYN in subflow_check_req()
+    - net: ravb: Fix dma_addr_t truncation in error case
+    - net: stmmac: ethtool: Fixed calltrace caused by unbalanced disable_irq_wake
+      calls
+    - bpf: Reject variable offset alu on PTR_TO_FLOW_KEYS
+    - net: dsa: vsc73xx: Add null pointer check to vsc73xx_gpio_probe
+    - netfilter: nf_tables: reject invalid set policy
+    - netfilter: nft_connlimit: move stateful fields out of expression data
+    - netfilter: nft_last: move stateful fields out of expression data
+    - netfilter: nft_quota: move stateful fields out of expression data
+    - netfilter: nft_limit: rename stateful structure
+    - netfilter: nft_limit: move stateful fields out of expression data
+    - netfilter: nf_tables: memcg accounting for dynamically allocated objects
+    - netfilter: nft_limit: do not ignore unsupported flags
+    - netfilter: nf_tables: do not allow mismatch field size and set key length
+    - netfilter: nf_tables: skip dead set elements in netlink dump
+    - netfilter: nf_tables: reject NFT_SET_CONCAT with not field length
+      description
+    - ipvs: avoid stat macros calls from preemptible context
+    - kdb: Fix a potential buffer overflow in kdb_local()
+    - ethtool: netlink: Add missing ethnl_ops_begin/complete
+    - mlxsw: spectrum_acl_erp: Fix error flow of pool allocation failure
+    - mlxsw: spectrum: Use 'bitmap_zalloc()' when applicable
+    - mlxsw: spectrum_acl_tcam: Add missing mutex_destroy()
+    - mlxsw: spectrum_acl_tcam: Make fini symmetric to init
+    - mlxsw: spectrum_acl_tcam: Reorder functions to avoid forward declarations
+    - mlxsw: spectrum_acl_tcam: Fix stack corruption
+    - selftests: mlxsw: qos_pfc: Adjust the test to support 8 lanes
+    - ipv6: mcast: fix data-race in ipv6_mc_down / mld_ifc_work
+    - i2c: s3c24xx: fix read transfers in polling mode
+    - i2c: s3c24xx: fix transferring more than one message in polling mode
+    - block: Remove special-casing of compound pages
+    - netfilter: nf_tables: typo NULL check in _clone() function
+    - netfilter: nft_connlimit: memleak if nf_ct_netns_get() fails
+    - netfilter: nft_limit: fix stateful object memory leak
+    - netfilter: nft_limit: Clone packet limits' cost value
+    - netfilter: nft_last: copy content when cloning expression
+    - netfilter: nft_quota: copy content when cloning expression
+    - arm64: dts: armada-3720-turris-mox: set irq type for RTC
+    - Revert "Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d""
+    - Linux 5.15.148
+  * CVE-2024-24855
+    - scsi: lpfc: Fix a possible data race in lpfc_unregister_fcf_rescan()
+  * performance: Scheduler: ratelimit updating of load_avg (LP: #2053251)
+    - sched/fair: Ratelimit update to tg->load_avg
+  * Jammy update: v5.15.147 upstream stable release (LP: #2054411)
+    - block: Don't invalidate pagecache for invalid falloc modes
+    - ALSA: hda/realtek: Fix mute and mic-mute LEDs for HP ProBook 440 G6
+    - Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"
+    - wifi: iwlwifi: pcie: don't synchronize IRQs from IRQ
+    - drm/bridge: ti-sn65dsi86: Never store more than msg->size bytes in AUX xfer
+    - nfc: llcp_core: Hold a ref to llcp_local->dev when holding a ref to
+      llcp_local
+    - octeontx2-af: Fix marking couple of structure as __packed
+    - drm/i915/dp: Fix passing the correct DPCD_REV for
+      drm_dp_set_phy_test_pattern
+    - i40e: Fix filter input checks to prevent config with invalid values
+    - igc: Report VLAN EtherType matching back to user
+    - igc: Check VLAN TCI mask
+    - igc: Check VLAN EtherType mask
+    - ASoC: fsl_rpmsg: Fix error handler with pm_runtime_enable
+    - mlxbf_gige: fix receive packet race condition
+    - net: sched: em_text: fix possible memory leak in em_text_destroy()
+    - r8169: Fix PCI error on system resume
+    - net: Implement missing getsockopt(SO_TIMESTAMPING_NEW)
+    - can: raw: add support for SO_TXTIME/SCM_TXTIME
+    - can: raw: add support for SO_MARK
+    - net-timestamp: extend SOF_TIMESTAMPING_OPT_ID to HW timestamps
+    - ARM: sun9i: smp: Fix array-index-out-of-bounds read in sunxi_mc_smp_init
+    - sfc: fix a double-free bug in efx_probe_filters
+    - net: bcmgenet: Fix FCS generation for fragmented skbuffs
+    - netfilter: nft_immediate: drop chain reference counter on error
+    - net: Save and restore msg_namelen in sock_sendmsg
+    - i40e: fix use-after-free in i40e_aqc_add_filters()
+    - ASoC: meson: g12a-toacodec: Validate written enum values
+    - ASoC: meson: g12a-tohdmitx: Validate written enum values
+    - ASoC: meson: g12a-toacodec: Fix event generation
+    - ASoC: meson: g12a-tohdmitx: Fix event generation for S/PDIF mux
+    - i40e: Restore VF MSI-X state during PCI reset
+    - igc: Fix hicredit calculation
+    - net/qla3xxx: fix potential memleak in ql_alloc_buffer_queues
+    - octeontx2-af: Don't enable Pause frames by default
+    - octeontx2-af: Set NIX link credits based on max LMAC
+    - octeontx2-af: Always configure NIX TX link credits based on max frame size
+    - octeontx2-af: Re-enable MAC TX in otx2_stop processing
+    - asix: Add check for usbnet_get_endpoints
+    - bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()
+    - net: Implement missing SO_TIMESTAMPING_NEW cmsg support
+    - selftests: secretmem: floor the memory size to the multiple of page_size
+    - mm/memory-failure: check the mapcount of the precise page
+    - firewire: ohci: suppress unexpected system reboot in AMD Ryzen machines and
+      ASM108x/VT630x PCIe cards
+    - x86/kprobes: fix incorrect return address calculation in
+      kprobe_emulate_call_indirect
+    - i2c: core: Fix atomic xfer check for non-preempt config
+    - mm: fix unmap_mapping_range high bits shift bug
+    - mmc: meson-mx-sdhc: Fix initialization frozen issue
+    - mmc: rpmb: fixes pause retune on all RPMB partitions.
+    - mmc: core: Cancel delayed work before releasing host
+    - mmc: sdhci-sprd: Fix eMMC init failure after hw reset
+    - ipv6: remove max_size check inline with ipv4
+    - perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
+    - kallsyms: Make module_kallsyms_on_each_symbol generally available
+    - tracing/kprobes: Fix symbol counting logic by looking at modules as well
+    - net: usb: ax88179_178a: remove redundant init code
+    - net: usb: ax88179_178a: move priv to driver_priv
+    - Linux 5.15.147
+  * CVE-2024-1085
+    - netfilter: nf_tables: check if catch-all set element is active in next
+      generation
+  * CVE-2023-23000
+    - phy: tegra: xusb: Fix return value of tegra_xusb_find_port_node function
+  * performance: mm/percpu-internal.h: Re-layout pcpu_chunk to mitigate false
+    sharing (LP: #2053152)
+    - percpu-internal/pcpu_chunk: re-layout pcpu_chunk structure to reduce false
+      sharing
+  * performance: address_space: add padding for i_map and i_mmap_rwsem to
+    mitigate a false sharing (LP: #2053069)
+    - fs/address_space: add alignment padding for i_map and i_mmap_rwsem to
+      mitigate a false sharing.
+  * cpufreq: intel_pstate: Enable HWP IO boost for all servers (LP: #2052817)
+    - cpufreq: intel_pstate: Enable HWP IO boost for all servers
+  * performance: mm/memcontrol.c: remove the redundant updating of
+    stats_flush_threshold (LP: #2052827)
+    - mm/memcontrol.c: remove the redundant updating of stats_flush_threshold
+  * Jammy update: v5.15.146 upstream stable release (LP: #2053212)
+    - ARM: dts: dra7: Fix DRA7 L3 NoC node register size
+    - ARM: OMAP2+: Fix null pointer dereference and memory leak in
+      omap_soc_device_init
+    - reset: Fix crash when freeing non-existent optional resets
+    - s390/vx: fix save/restore of fpu kernel context
+    - wifi: iwlwifi: pcie: add another missing bh-disable for rxq->lock
+    - wifi: mac80211: mesh_plink: fix matches_local logic
+    - net/mlx5e: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list()
+    - net/mlx5e: fix a potential double-free in fs_udp_create_groups
+    - net/mlx5: Fix fw tracer first block check
+    - net/mlx5e: Correct snprintf truncation handling for fw_version buffer used
+      by representors
+    - net: sched: ife: fix potential use-after-free
+    - ethernet: atheros: fix a memleak in atl1e_setup_ring_resources
+    - net/rose: fix races in rose_kill_by_device()
+    - net: mana: select PAGE_POOL
+    - net: check vlan filter feature in vlan_vids_add_by_dev() and
+      vlan_vids_del_by_dev()
+    - afs: Fix the dynamic root's d_delete to always delete unused dentries
+    - afs: Fix dynamic root lookup DNS check
+    - net: check dev->gso_max_size in gso_features_check()
+    - keys, dns: Allow key types (eg. DNS) to be reclaimed immediately on expiry
+    - keys, dns: Fix missing size check of V1 server-list header
+    - keys, dns: Fix size check of V1 server-list header
+    - afs: Fix overwriting of result of DNS query
+    - afs: Use refcount_t rather than atomic_t
+    - afs: Fix use-after-free due to get/remove race in volume tree
+    - ASoC: hdmi-codec: fix missing report for jack initial status
+    - i2c: aspeed: Handle the coalesced stop conditions with the start conditions.
+    - pinctrl: at91-pio4: use dedicated lock class for IRQ
+    - gpiolib: cdev: add gpio_device locking wrapper around gpio_ioctl()
+    - ksmbd: fix wrong name of SMB2_CREATE_ALLOCATION_SIZE
+    - drm/i915/mtl: limit second scaler vertical scaling in ver >= 14
+    - drm/i915: Relocate intel_atomic_setup_scalers()
+    - drm/i915: Fix intel_atomic_setup_scalers() plane_state handling
+    - smb: client: fix NULL deref in asn1_ber_decoder()
+    - smb: client: fix OOB in smb2_query_reparse_point()
+    - interconnect: Treat xlate() returning NULL node as an error
+    - iio: imu: inv_mpu6050: fix an error code problem in inv_mpu6050_read_raw
+    - Input: ipaq-micro-keys - add error handling for devm_kmemdup
+    - scsi: bnx2fc: Fix skb double free in bnx2fc_rcv()
+    - iio: common: ms_sensors: ms_sensors_i2c: fix humidity conversion time table
+    - iio: adc: ti_am335x_adc: Fix return value check of tiadc_request_dma()
+    - iio: triggered-buffer: prevent possible freeing of wrong buffer
+    - ALSA: usb-audio: Increase delay in MOTU M quirk
+    - wifi: cfg80211: Add my certificate
+    - wifi: cfg80211: fix certs build to not depend on file order
+    - USB: serial: ftdi_sio: update Actisense PIDs constant names
+    - USB: serial: option: add Quectel EG912Y module support
+    - USB: serial: option: add Foxconn T99W265 with new baseline
+    - USB: serial: option: add Quectel RM500Q R13 firmware support
+    - Bluetooth: hci_event: Fix not checking if HCI_OP_INQUIRY has been sent
+    - Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE
+    - Input: soc_button_array - add mapping for airplane mode button
+    - net: 9p: avoid freeing uninit memory in p9pdu_vreadf
+    - net: rfkill: gpio: set GPIO direction
+    - net: ks8851: Fix TX stall caused by TX buffer overrun
+    - dt-bindings: nvmem: mxs-ocotp: Document fsl,ocotp
+    - scsi: core: Always send batch on reset or error handling command
+    - tracing / synthetic: Disable events after testing in
+      synth_event_gen_test_init()
+    - bus: ti-sysc: Flush posted write only after srst_udelay
+    - gpio: dwapb: mask/unmask IRQ when disable/enale it
+    - lib/vsprintf: Fix %pfwf when current node refcount == 0
+    - KVM: arm64: vgic: Force vcpu vgic teardown on vcpu destroy
+    - x86/alternatives: Sync core before enabling interrupts
+    - fuse: share lookup state between submount and its parent
+    - ksmbd: have a dependency on cifs ARC4
+    - ksmbd: set epoch in create context v2 lease
+    - ksmbd: set v2 lease capability
+    - ksmbd: downgrade RWH lease caching state to RH for directory
+    - ksmbd: send v2 lease break notification for directory
+    - ksmbd: lazy v2 lease break on smb2_write()
+    - ksmbd: avoid duplicate opinfo_put() call on error of smb21_lease_break_ack()
+    - ksmbd: fix wrong allocation size update in smb2_open()
+    - ARM: dts: Fix occasional boot hang for am3 usb
+    - usb: fotg210-hcd: delete an incorrect bounds test
+    - ethernet: constify references to netdev->dev_addr in drivers
+    - net: usb: ax88179_178a: clean up pm calls
+    - net: usb: ax88179_178a: wol optimizations
+    - net: usb: ax88179_178a: avoid failed operations when device is disconnected
+    - device property: Add const qualifier to device_get_match_data() parameter
+    - spi: Introduce spi_get_device_match_data() helper
+    - iio: imu: adis16475: add spi_device_id table
+    - smb: client: fix OOB in SMB2_query_info_init()
+    - mm/filemap: avoid buffered read/write race to read inconsistent data
+    - ring-buffer: Fix wake ups when buffer_percent is set to 100
+    - tracing: Fix blocked reader of snapshot buffer
+    - ring-buffer: Remove useless update to write_stamp in rb_try_to_discard()
+    - ring-buffer: Fix slowpath of interrupted event
+    - dm-integrity: don't modify bio's immutable bio_vec in integrity_metadata()
+    - device property: Allow const parameter to dev_fwnode()
+    - bpf: Fix prog_array_map_poke_run map poke update
+    - Linux 5.15.146
+  * CVE-2023-46838
+    - xen-netback: don't produce zero-size SKB frags
+  * CVE-2024-1086
+    - netfilter: nf_tables: reject QUEUE/DROP verdict parameters
+  * disable Intel DMA remapping by default (LP: #1971699)
+    - [Config] update tracking bug for CONFIG_INTEL_IOMMU_DEFAULT_ON
+  * Validate connection interval to pass Bluetooth Test Suite (LP: #2052005)
+    - Bluetooth: Enforce validation on max value of connection interval
+  * Jammy update: v5.15.145 upstream stable release (LP: #2052406)
+    - ksmbd: use ksmbd_req_buf_next() in ksmbd_verify_smb_message()
+    - ksmdb: use cmd helper variable in smb2_get_ksmbd_tcon()
+    - ksmbd: Remove redundant 'flush_workqueue()' calls
+    - ksmbd: remove md4 leftovers
+    - ksmbd: remove smb2_buf_length in smb2_hdr
+    - ksmbd: remove smb2_buf_length in smb2_transform_hdr
+    - ksmbd: change LeaseKey data type to u8 array
+    - ksmbd: use oid registry functions to decode OIDs
+    - ksmbd: Remove unused parameter from smb2_get_name()
+    - ksmbd: Remove unused fields from ksmbd_file struct definition
+    - ksmbd: set both ipv4 and ipv6 in FSCTL_QUERY_NETWORK_INTERFACE_INFO
+    - ksmbd: Fix buffer_check_err() kernel-doc comment
+    - ksmbd: Fix smb2_set_info_file() kernel-doc comment
+    - ksmbd: Delete an invalid argument description in
+      smb2_populate_readdir_entry()
+    - ksmbd: Fix smb2_get_name() kernel-doc comment
+    - ksmbd: register ksmbd ib client with ib_register_client()
+    - ksmbd: set 445 port to smbdirect port by default
+    - ksmbd: smbd: call rdma_accept() under CM handler
+    - ksmbd: smbd: create MR pool
+    - ksmbd: smbd: change the default maximum read/write, receive size
+    - ksmbd: smbd: fix missing client's memory region invalidation
+    - ksmbd: smbd: validate buffer descriptor structures
+    - ksmbd: add support for key exchange
+    - ksmbd: use netif_is_bridge_port
+    - ksmbd: store fids as opaque u64 integers
+    - ksmbd: shorten experimental warning on loading the module
+    - ksmbd: Remove a redundant zeroing of memory
+    - ksmbd: replace usage of found with dedicated list iterator variable
+    - smb3: fix ksmbd bigendian bug in oplock break, and move its struct to
+      smbfs_common
+    - ksmbd: remove filename in ksmbd_file
+    - ksmbd: smbd: change prototypes of RDMA read/write related functions
+    - ksmbd: smbd: introduce read/write credits for RDMA read/write
+    - ksmbd: smbd: simplify tracking pending packets
+    - ksmbd: smbd: change the return value of get_sg_list
+    - ksmbd: smbd: handle multiple Buffer descriptors
+    - ksmbd: fix wrong smbd max read/write size check
+    - ksmbd: Fix some kernel-doc comments
+    - ksmbd: smbd: fix connection dropped issue
+    - ksmbd: smbd: relax the count of sges required
+    - ksmbd: smbd: Remove useless license text when SPDX-License-Identifier is
+      already used
+    - ksmbd: remove duplicate flag set in smb2_write
+    - ksmbd: remove unused ksmbd_share_configs_cleanup function
+    - ksmbd: use wait_event instead of schedule_timeout()
+    - ksmbd: request update to stale share config
+    - ksmbd: remove unnecessary generic_fillattr in smb2_open
+    - ksmbd: don't open-code file_path()
+    - ksmbd: don't open-code %pD
+    - ksmbd: constify struct path
+    - ksmbd: remove generic_fillattr use in smb2_open()
+    - ksmbd: casefold utf-8 share names and fix ascii lowercase conversion
+    - ksmbd: change security id to the one samba used for posix extension
+    - ksmbd: set file permission mode to match Samba server posix extension
+      behavior
+    - ksmbd: fill sids in SMB_FIND_FILE_POSIX_INFO response
+    - ksmbd: fix encryption failure issue for session logoff response
+    - ksmbd: set NTLMSSP_NEGOTIATE_SEAL flag to challenge blob
+    - ksmbd: decrease the number of SMB3 smbdirect server SGEs
+    - ksmbd: reduce server smbdirect max send/receive segment sizes
+    - ksmbd: hide socket error message when ipv6 config is disable
+    - ksmbd: make utf-8 file name comparison work in __caseless_lookup()
+    - ksmbd: call ib_drain_qp when disconnected
+    - ksmbd: validate share name from share config response
+    - ksmbd: replace one-element arrays with flexible-array members
+    - ksmbd: set SMB2_SESSION_FLAG_ENCRYPT_DATA when enforcing data encryption for
+      this share
+    - ksmbd: use F_SETLK when unlocking a file
+    - ksmbd: Fix resource leak in smb2_lock()
+    - ksmbd: Convert to use sysfs_emit()/sysfs_emit_at() APIs
+    - ksmbd: send proper error response in smb2_tree_connect()
+    - ksmbd: Implements sess->rpc_handle_list as xarray
+    - ksmbd: fix typo, syncronous->synchronous
+    - ksmbd: Remove duplicated codes
+    - ksmbd: update Kconfig to note Kerberos support and fix indentation
+    - ksmbd: Fix spelling mistake "excceed" -> "exceeded"
+    - ksmbd: Fix parameter name and comment mismatch
+    - ksmbd: fix possible memory leak in smb2_lock()
+    - ksmbd: fix wrong signingkey creation when encryption is AES256
+    - ksmbd: remove unused is_char_allowed function
+    - ksmbd: delete asynchronous work from list
+    - ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
+    - ksmbd: avoid out of bounds access in decode_preauth_ctxt()
+    - ksmbd: set NegotiateContextCount once instead of every inc
+    - ksmbd: avoid duplicate negotiate ctx offset increments
+    - ksmbd: remove unused compression negotiate ctx packing
+    - fs: introduce lock_rename_child() helper
+    - ksmbd: fix racy issue from using ->d_parent and ->d_name
+    - ksmbd: destroy expired sessions
+    - ksmbd: block asynchronous requests when making a delay on session setup
+    - ksmbd: fix racy issue from smb2 close and logoff with multichannel
+    - ksmbd: fix racy issue under cocurrent smb2 tree disconnect
+    - ksmbd: fix uninitialized pointer read in ksmbd_vfs_rename()
+    - ksmbd: fix uninitialized pointer read in smb2_create_link()
+    - ksmbd: fix multiple out-of-bounds read during context decoding
+    - ksmbd: fix UAF issue from opinfo->conn
+    - ksmbd: call putname after using the last component
+    - ksmbd: fix out-of-bound read in deassemble_neg_contexts()
+    - ksmbd: fix out-of-bound read in parse_lease_state()
+    - ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
+    - ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
+    - ksmbd: validate smb request protocol id
+    - ksmbd: add mnt_want_write to ksmbd vfs functions
+    - ksmbd: remove unused ksmbd_tree_conn_share function
+    - ksmbd: use kzalloc() instead of __GFP_ZERO
+    - ksmbd: return a literal instead of 'err' in ksmbd_vfs_kern_path_locked()
+    - ksmbd: Change the return value of ksmbd_vfs_query_maximal_access to void
+    - ksmbd: use kvzalloc instead of kvmalloc
+    - ksmbd: Replace the ternary conditional operator with min()
+    - ksmbd: fix out of bounds read in smb2_sess_setup
+    - ksmbd: add missing compound request handing in some commands
+    - ksmbd: Use struct_size() helper in ksmbd_negotiate_smb_dialect()
+    - ksmbd: Replace one-element array with flexible-array member
+    - ksmbd: Fix unsigned expression compared with zero
+    - ksmbd: check if a mount point is crossed during path lookup
+    - ksmbd: validate session id and tree id in compound request
+    - ksmbd: fix out of bounds in init_smb2_rsp_hdr()
+    - ksmbd: switch to use kmemdup_nul() helper
+    - ksmbd: add support for read compound
+    - ksmbd: fix wrong interim response on compound
+    - ksmbd: fix `force create mode' and `force directory mode'
+    - ksmbd: reduce descriptor size if remaining bytes is less than request size
+    - ksmbd: Fix one kernel-doc comment
+    - ksmbd: fix slub overflow in ksmbd_decode_ntlmssp_auth_blob()
+    - ksmbd: add missing calling smb2_set_err_rsp() on error
+    - ksmbd: remove experimental warning
+    - ksmbd: remove unneeded mark_inode_dirty in set_info_sec()
+    - ksmbd: fix passing freed memory 'aux_payload_buf'
+    - ksmbd: return invalid parameter error response if smb2 request is invalid
+    - ksmbd: check iov vector index in ksmbd_conn_write()
+    - ksmbd: fix race condition between session lookup and expire
+    - ksmbd: fix race condition with fp
+    - ksmbd: fix race condition from parallel smb2 logoff requests
+    - ksmbd: fix race condition from parallel smb2 lock requests
+    - ksmbd: fix race condition between tree conn lookup and disconnect
+    - ksmbd: fix wrong error response status by using set_smb2_rsp_status()
+    - ksmbd: fix Null pointer dereferences in ksmbd_update_fstate()
+    - ksmbd: fix potential double free on smb2_read_pipe() error path
+    - ksmbd: Remove unused field in ksmbd_user struct
+    - ksmbd: reorganize ksmbd_iov_pin_rsp()
+    - ksmbd: fix kernel-doc comment of ksmbd_vfs_setxattr()
+    - ksmbd: fix recursive locking in vfs helpers
+    - ksmbd: fix missing RDMA-capable flag for IPoIB device in
+      ksmbd_rdma_capable_netdev()
+    - ksmbd: add support for surrogate pair conversion
+    - ksmbd: no need to wait for binded connection termination at logoff
+    - ksmbd: fix kernel-doc comment of ksmbd_vfs_kern_path_locked()
+    - ksmbd: handle malformed smb1 message
+    - ksmbd: prevent memory leak on error return
+    - ksmbd: fix possible deadlock in smb2_open
+    - ksmbd: separately allocate ci per dentry
+    - ksmbd: move oplock handling after unlock parent dir
+    - ksmbd: release interim response after sending status pending response
+    - ksmbd: move setting SMB2_FLAGS_ASYNC_COMMAND and AsyncId
+    - ksmbd: don't update ->op_state as OPLOCK_STATE_NONE on error
+    - tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols
+    - kasan: disable kasan_non_canonical_hook() for HW tags
+    - Linux 5.15.145
+  * Jammy update: v5.15.144 upstream stable release (LP: #2052404)
+    - r8152: add vendor/device ID pair for D-Link DUB-E250
+    - r8152: add vendor/device ID pair for ASUS USB-C2500
+    - netfilter: nf_tables: fix 'exist' matching on bigendian arches
+    - mm/memory_hotplug: handle memblock_add_node() failures in
+      add_memory_resource()
+    - memblock: allow to specify flags with memblock_add_node()
+    - MIPS: Loongson64: Handle more memory types passed from firmware
+    - ksmbd: fix memory leak in smb2_lock()
+    - afs: Fix refcount underflow from error handling race
+    - HID: lenovo: Restrict detection of patched firmware only to USB cptkbd
+    - net: ipv6: support reporting otherwise unknown prefix flags in RTM_NEWPREFIX
+    - qca_debug: Prevent crash on TX ring changes
+    - qca_debug: Fix ethtool -G iface tx behavior
+    - qca_spi: Fix reset behavior
+    - atm: solos-pci: Fix potential deadlock on &cli_queue_lock
+    - atm: solos-pci: Fix potential deadlock on &tx_queue_lock
+    - net: vlan: introduce skb_vlan_eth_hdr()
+    - net: fec: correct queue selection
+    - octeontx2-af: fix a use-after-free in rvu_nix_register_reporters
+    - octeontx2-pf: Fix promisc mcam entry action
+    - octeontx2-af: Update RSS algorithm index
+    - qed: Fix a potential use-after-free in qed_cxt_tables_alloc
+    - net: Remove acked SYN flag from packet in the transmit queue correctly
+    - net: ena: Destroy correct number of xdp queues upon failure
+    - net: ena: Fix xdp drops handling due to multibuf packets
+    - net: ena: Fix XDP redirection error
+    - stmmac: dwmac-loongson: Make sure MDIO is initialized before use
+    - sign-file: Fix incorrect return values check
+    - vsock/virtio: Fix unsigned integer wrap around in
+      virtio_transport_has_space()
+    - dpaa2-switch: fix size of the dma_unmap
+    - net: stmmac: use dev_err_probe() for reporting mdio bus registration failure
+    - net: stmmac: Handle disabled MDIO busses from devicetree
+    - net: atlantic: fix double free in ring reinit logic
+    - cred: switch to using atomic_long_t
+    - fuse: dax: set fc->dax to NULL in fuse_dax_conn_free()
+    - ALSA: hda/hdmi: add force-connect quirk for NUC5CPYB
+    - ALSA: hda/hdmi: add force-connect quirks for ASUSTeK Z170 variants
+    - ALSA: hda/realtek: Apply mute LED quirk for HP15-db
+    - PCI: loongson: Limit MRRS to 256
+    - drm/mediatek: Add spinlock for setting vblank event in atomic_begin
+    - usb: aqc111: check packet for fixup for true limit
+    - stmmac: dwmac-loongson: Add architecture dependency
+    - [Config] updateconfigs for CONFIG_DWMAC_LOONGSON
+    - blk-throttle: fix lockdep warning of "cgroup_mutex or RCU read lock
+      required!"
+    - blk-cgroup: bypass blkcg_deactivate_policy after destroying
+    - bcache: avoid oversize memory allocation by small stripe_size
+    - bcache: remove redundant assignment to variable cur_idx
+    - bcache: add code comments for bch_btree_node_get() and
+      __bch_btree_node_alloc()
+    - bcache: avoid NULL checking to c->root in run_cache_set()
+    - platform/x86: intel_telemetry: Fix kernel doc descriptions
+    - HID: glorious: fix Glorious Model I HID report
+    - HID: add ALWAYS_POLL quirk for Apple kb
+    - HID: hid-asus: reset the backlight brightness level on resume
+    - HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
+    - asm-generic: qspinlock: fix queued_spin_value_unlocked() implementation
+    - net: usb: qmi_wwan: claim interface 4 for ZTE MF290
+    - HID: hid-asus: add const to read-only outgoing usb buffer
+    - btrfs: do not allow non subvolume root targets for snapshot
+    - soundwire: stream: fix NULL pointer dereference for multi_link
+    - ext4: prevent the normalized size from exceeding EXT_MAX_BLOCKS
+    - arm64: mm: Always make sw-dirty PTEs hw-dirty in pte_modify
+    - team: Fix use-after-free when an option instance allocation fails
+    - drm/amdgpu/sdma5.2: add begin/end_use ring callbacks
+    - ring-buffer: Fix memory leak of free page
+    - tracing: Update snapshot buffer on resize if it is allocated
+    - ring-buffer: Do not update before stamp when switching sub-buffers
+    - ring-buffer: Have saved event hold the entire event
+    - ring-buffer: Fix writing to the buffer with max_data_size
+    - ring-buffer: Fix a race in rb_time_cmpxchg() for 32 bit archs
+    - ring-buffer: Do not try to put back write_stamp
+    - USB: gadget: core: adjust uevent timing on gadget unbind
+    - powerpc/ftrace: Create a dummy stackframe to fix stack unwind
+    - powerpc/ftrace: Fix stack teardown in ftrace_no_trace
+    - r8152: avoid to change cfg for all devices
+    - r8152: remove rtl_vendor_mode function
+    - r8152: fix the autosuspend doesn't work
+    - Linux 5.15.144
+  * CVE-2023-32247
+    - ksmbd: destroy expired sessions
+  * CVE-2024-22705
+    - ksmbd: fix slab-out-of-bounds in smb_strndup_from_utf16()
+
+  [ Ubuntu: 5.15.0-100.110 ]
+
+  * jammy/linux: 5.15.0-100.110 -proposed tracker (LP: #2052616)
+  * i915 regression introduced with 5.5 kernel (LP: #2044131)
+    - drm/i915: Skip some timing checks on BXT/GLK DSI transcoders
+  * Audio balancing setting doesn't work with the cirrus codec (LP: #2051050)
+    - ALSA: hda/cs8409: Suppress vmaster control for Dolphin models
+  * partproke is broken on empty loopback device (LP: #2049689)
+    - block: Move checking GENHD_FL_NO_PART to bdev_add_partition()
+  * CVE-2023-0340
+    - vhost: use kzalloc() instead of kmalloc() followed by memset()
+  * CVE-2023-51780
+    - atm: Fix Use-After-Free in do_vcc_ioctl
+  * CVE-2023-6915
+    - ida: Fix crash in ida_free when the bitmap is empty
+  * CVE-2024-0646
+    - net: tls, update curr on splice as well
+  * CVE-2024-0565
+    - smb: client: fix OOB in receive_encrypted_standard()
+  * CVE-2023-51781
+    - appletalk: Fix Use-After-Free in atalk_ioctl
+  * Jammy update: v5.15.143 upstream stable release (LP: #2050858)
+    - vdpa/mlx5: preserve CVQ vringh index
+    - hrtimers: Push pending hrtimers away from outgoing CPU earlier
+    - i2c: designware: Fix corrupted memory seen in the ISR
+    - netfilter: ipset: fix race condition between swap/destroy and kernel side
+      add/del/test
+    - tg3: Move the [rt]x_dropped counters to tg3_napi
+    - tg3: Increment tx_dropped in tg3_tso_bug()
+    - kconfig: fix memory leak from range properties
+    - drm/amdgpu: correct chunk_ptr to a pointer to chunk.
+    - platform/x86: asus-wmi: Adjust tablet/lidflip handling to use enum
+    - platform/x86: asus-wmi: Add support for ROG X13 tablet mode
+    - platform/x86: asus-wmi: Simplify tablet-mode-switch probing
+    - platform/x86: asus-wmi: Simplify tablet-mode-switch handling
+    - platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code
+    - of: dynamic: Fix of_reconfig_get_state_change() return value documentation
+    - platform/x86: wmi: Allow duplicate GUIDs for drivers that use struct
+      wmi_driver
+    - platform/x86: wmi: Skip blocks with zero instances
+    - ipv6: fix potential NULL deref in fib6_add()
+    - octeontx2-pf: Add missing mutex lock in otx2_get_pauseparam
+    - octeontx2-af: Check return value of nix_get_nixlf before using nixlf
+    - hv_netvsc: rndis_filter needs to select NLS
+    - r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
+    - r8152: Add RTL8152_INACCESSIBLE checks to more loops
+    - r8152: Add RTL8152_INACCESSIBLE to r8156b_wait_loading_flash()
+    - r8152: Add RTL8152_INACCESSIBLE to r8153_pre_firmware_1()
+    - r8152: Add RTL8152_INACCESSIBLE to r8153_aldps_en()
+    - mlxbf-bootctl: correctly identify secure boot with development keys
+    - platform/mellanox: Add null pointer checks for devm_kasprintf()
+    - platform/mellanox: Check devm_hwmon_device_register_with_groups() return
+      value
+    - arcnet: restoring support for multiple Sohard Arcnet cards
+    - net: stmmac: fix FPE events losing
+    - octeontx2-af: fix a use-after-free in rvu_npa_register_reporters
+    - i40e: Fix unexpected MFS warning message
+    - net: bnxt: fix a potential use-after-free in bnxt_init_tc
+    - ionic: fix snprintf format length warning
+    - ionic: Fix dim work handling in split interrupt mode
+    - ipv4: ip_gre: Avoid skb_pull() failure in ipgre_xmit()
+    - net: hns: fix fake link up on xge port
+    - octeontx2-af: Update Tx link register range
+    - netfilter: nf_tables: validate family when identifying table via handle
+    - netfilter: xt_owner: Fix for unsafe access of sk->sk_socket
+    - tcp: do not accept ACK of bytes we never sent
+    - bpf: sockmap, updating the sg structure should also update curr
+    - psample: Require 'CAP_NET_ADMIN' when joining "packets" group
+    - net: add missing kdoc for struct genl_multicast_group::flags
+    - drop_monitor: Require 'CAP_SYS_ADMIN' when joining "events" group
+    - tee: optee: Fix supplicant based device enumeration
+    - RDMA/hns: Fix unnecessary err return when using invalid congest control
+      algorithm
+    - RDMA/irdma: Do not modify to SQD on error
+    - RDMA/irdma: Add wait for suspend on SQD
+    - arm64: dts: rockchip: Expand reg size of vdec node for RK3399
+    - RDMA/rtrs-srv: Do not unconditionally enable irq
+    - RDMA/rtrs-clt: Start hb after path_up
+    - RDMA/rtrs-srv: Check return values while processing info request
+    - RDMA/rtrs-srv: Free srv_mr iu only when always_invalidate is true
+    - RDMA/rtrs-srv: Destroy path files after making sure no IOs in-flight
+    - RDMA/rtrs-clt: Fix the max_send_wr setting
+    - RDMA/rtrs-clt: Remove the warnings for req in_use check
+    - RDMA/bnxt_re: Correct module description string
+    - hwmon: (acpi_power_meter) Fix 4.29 MW bug
+    - hwmon: (nzxt-kraken2) Fix error handling path in kraken2_probe()
+    - ASoC: wm_adsp: fix memleak in wm_adsp_buffer_populate
+    - RDMA/core: Fix umem iterator when PAGE_SIZE is greater then HCA pgsz
+    - RDMA/irdma: Avoid free the non-cqp_request scratch
+    - arm64: dts: imx8mq: drop usb3-resume-missing-cas from usb
+    - arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
+    - ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
+    - tracing: Fix a warning when allocating buffered events fails
+    - scsi: be2iscsi: Fix a memleak in beiscsi_init_wrb_handle()
+    - ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
+    - ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
+    - ARM: dts: imx28-xea: Pass the 'model' property
+    - riscv: fix misaligned access handling of C.SWSP and C.SDSP
+    - md: introduce md_ro_state
+    - md: don't leave 'MD_RECOVERY_FROZEN' in error path of md_set_readonly()
+    - kprobes: consistent rcu api usage for kretprobe holder
+    - nvme-pci: Add sleep quirk for Kingston drives
+    - io_uring: fix mutex_unlock with unreferenced ctx
+    - ALSA: usb-audio: Add Pioneer DJM-450 mixer controls
+    - ALSA: pcm: fix out-of-bounds in snd_pcm_state_names
+    - nilfs2: fix missing error check for sb_set_blocksize call
+    - nilfs2: prevent WARNING in nilfs_sufile_set_segment_usage()
+    - checkstack: fix printed address
+    - tracing: Always update snapshot buffer size
+    - tracing: Disable snapshot buffer when stopping instance tracers
+    - tracing: Fix incomplete locking when disabling buffered events
+    - tracing: Fix a possible race when disabling buffered events
+    - packet: Move reference count in packet_sock to atomic_long_t
+    - regmap: fix bogus error on regcache_sync success
+    - platform/surface: aggregator: fix recv_buf() return value
+    - arm64: dts: mediatek: mt7622: fix memory node warning check
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: fix dsi unnecessary cells
+      properties
+    - arm64: dts: mediatek: mt8173-evb: Fix regulator-fixed node names
+    - arm64: dts: mediatek: mt8183: Fix unit address for scp reserved memory
+    - binder: fix memory leaks of spam and pending work
+    - kallsyms: Make kallsyms_on_each_symbol generally available
+    - coresight: etm4x: Make etm4_remove_dev() return void
+    - coresight: etm4x: Remove bogous __exit annotation for some functions
+    - misc: mei: client.c: return negative error code in mei_cl_write
+    - misc: mei: client.c: fix problem of return '-EOVERFLOW' in mei_cl_write
+    - ring-buffer: Force absolute timestamp on discard of event
+    - tracing: Set actual size after ring buffer resize
+    - tracing: Stop current tracer when resizing buffer
+    - r8169: fix rtl8125b PAUSE frames blasting when suspended
+    - mm: fix oops when filemap_map_pmd() without prealloc_pte
+    - io_uring/af_unix: disable sending io_uring over sockets
+    - platform/x86: asus-wmi: Fix kbd_dock_devid tablet-switch reporting
+    - docs/process/howto: Replace C89 with C11
+    - tools headers UAPI: Sync linux/perf_event.h with the kernel sources
+    - arm64: dts: mediatek: align thermal zone node names with dtschema
+    - arm64: dts: mediatek: mt8183: Move thermal-zones to the root node
+    - arm64: dts: mediatek: add missing space before {
+    - arm64: dts: mt8183: kukui: Fix underscores in node names
+    - gpiolib: sysfs: Fix error handling on failed export
+    - drm/amd/amdgpu: Fix warnings in amdgpu/amdgpu_display.c
+    - drm/amdgpu: correct the amdgpu runtime dereference usage count
+    - usb: gadget: f_hid: fix report descriptor allocation
+    - parport: Add support for Brainboxes IX/UC/PX parallel cards
+    - usb: typec: class: fix typec_altmode_put_partner to put plugs
+    - ARM: PL011: Fix DMA support
+    - serial: sc16is7xx: address RX timeout interrupt errata
+    - serial: 8250: 8250_omap: Clear UART_HAS_RHR_IT_DIS bit
+    - serial: 8250: 8250_omap: Do not start RX DMA on THRI interrupt
+    - serial: 8250_omap: Add earlycon support for the AM654 UART controller
+    - x86/CPU/AMD: Check vendor in the AMD microcode callback
+    - KVM: s390/mm: Properly reset no-dat
+    - KVM: SVM: Update EFER software model on CR0 trap for SEV-ES
+    - MIPS: Loongson64: Reserve vgabios memory on boot
+    - MIPS: Loongson64: Enable DMA noncoherent support
+    - cifs: Fix non-availability of dedup breaking generic/304
+    - smb: client: fix potential NULL deref in parse_dfs_referrals()
+    - devcoredump : Serialize devcd_del work
+    - devcoredump: Send uevent once devcd is ready
+    - Linux 5.15.143
+  * Intel E810-XXV - NETDEV WATCHDOG: (ice): transmit queue timed out
+    (LP: #2036239)
+    - ice: Add feature bitmap, helpers and a check for DSCP
+    - ice: Add driver support for firmware changes for LAG
+    - ice: alter feature support check for SRIOV and LAG
+  * Don't WARN_ON_ONCE() for a broken discovery table (LP: #2048404)
+    - perf/x86/uncore: Don't WARN_ON_ONCE() for a broken discovery table
+  * Reject connection when malformed L2CAP signal packet is received
+    (LP: #2047634)
+    - Bluetooth: L2CAP: Send reject on command corrupted request
+  * Jammy update: v5.15.142 upstream stable release (LP: #2050849)
+    - pinctrl: avoid reload of p state in list iteration
+    - firewire: core: fix possible memory leak in create_units()
+    - mmc: cqhci: Increase recovery halt timeout
+    - mmc: cqhci: Warn of halt or task clear failure
+    - mmc: cqhci: Fix task clearing in CQE error recovery
+    - mmc: block: Retry commands in CQE error recovery
+    - mmc: block: Do not lose cache flush during CQE error recovery
+    - mmc: block: Be sure to wait while busy in CQE error recovery
+    - ALSA: hda: Disable power-save on KONTRON SinglePC
+    - ALSA: hda/realtek: Headset Mic VREF to 100%
+    - ALSA: hda/realtek: Add supported ALC257 for ChromeOS
+    - dm-verity: align struct dm_verity_fec_io properly
+    - dm verity: don't perform FEC for failed readahead IO
+    - bcache: revert replacing IS_ERR_OR_NULL with IS_ERR
+    - iommu/vt-d: Add MTL to quirk list to skip TE disabling
+    - powerpc: Don't clobber f0/vs0 during fp|altivec register save
+    - parisc: Drop the HP-UX ENOSYM and EREMOTERELEASE error codes
+    - btrfs: ref-verify: fix memory leaks in btrfs_ref_tree_mod()
+    - btrfs: fix off-by-one when checking chunk map includes logical address
+    - btrfs: send: ensure send_fd is writable
+    - btrfs: make error messages more clear when getting a chunk map
+    - Input: xpad - add HyperX Clutch Gladiate Support
+    - vlan: introduce vlan_dev_free_egress_priority
+    - vlan: move dev_put into vlan_dev_uninit
+    - rcu: Avoid tracing a few functions executed in stop machine
+    - hv_netvsc: fix race of netvsc and VF register_netdevice
+    - USB: core: Change configuration warnings to notices
+    - usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
+    - dpaa2-eth: increase the needed headroom to account for alignment
+    - uapi: propagate __struct_group() attributes to the container union
+    - selftests/net: ipsec: fix constant out of range
+    - octeontx2-af: Fix possible buffer overflow
+    - net: stmmac: xgmac: Disable FPE MMC interrupts
+    - octeontx2-pf: Fix adding mbox work queue entry when num_vfs > 64
+    - Revert "workqueue: remove unused cancel_work()"
+    - r8169: prevent potential deadlock in rtl8169_close
+    - ravb: Fix races between ravb_tx_timeout_work() and net related ops
+    - net: ravb: Check return value of reset_control_deassert()
+    - net: ravb: Use pm_runtime_resume_and_get()
+    - net: ravb: Start TX queues after HW initialization succeeded
+    - net: ravb: Stop DMA in case of failures on ravb_open()
+    - perf intel-pt: Fix async branch flags
+    - selftests/resctrl: Add missing SPDX license to Makefile
+    - selftests/resctrl: Move _GNU_SOURCE define into Makefile
+    - smb3: fix touch -h of symlink
+    - ASoC: Intel: Move soc_intel_is_foo() helpers to a generic header
+    - ASoC: SOF: sof-pci-dev: use community key on all Up boards
+    - ASoC: SOF: sof-pci-dev: add parameter to override topology filename
+    - ASoC: SOF: sof-pci-dev: don't use the community key on APL Chromebooks
+    - ASoC: SOF: sof-pci-dev: Fix community key quirk detection
+    - fbdev: stifb: Make the STI next font pointer a 32-bit signed offset
+    - fs: add ctime accessors infrastructure
+    - smb3: fix caching of ctime on setxattr
+    - cpufreq: imx6q: don't warn for disabling a non-existing frequency
+    - cpufreq: imx6q: Don't disable 792 Mhz OPP unnecessarily
+    - iommu/vt-d: Omit devTLB invalidation requests when TES=0
+    - iommu/vt-d: Make context clearing consistent with context mapping
+    - mmc: core: add helpers mmc_regulator_enable/disable_vqmmc
+    - mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled
+    - r8169: disable ASPM in case of tx timeout
+    - r8169: fix deadlock on RTL8125 in jumbo mtu mode
+    - iomap: update ki_pos a little later in iomap_dio_complete
+    - Linux 5.15.142
+  * Jammy update: v5.15.141 upstream stable release (LP: #2050044)
+    - afs: Fix afs_server_list to be cleaned up with RCU
+    - afs: Make error on cell lookup failure consistent with OpenAFS
+    - drm/panel: boe-tv101wum-nl6: Fine tune the panel power sequence
+    - drm/panel: auo,b101uan08.3: Fine tune the panel power sequence
+    - drm/panel: simple: Fix Innolux G101ICE-L01 bus flags
+    - drm/panel: simple: Fix Innolux G101ICE-L01 timings
+    - wireguard: use DEV_STATS_INC()
+    - octeontx2-pf: Fix memory leak during interface down
+    - ata: pata_isapnp: Add missing error check for devm_ioport_map()
+    - drm/rockchip: vop: Fix color for RGB888/BGR888 format on VOP full
+    - HID: core: store the unique system identifier in hid_device
+    - HID: fix HID device resource race between HID core and debugging support
+    - ipv4: Correct/silence an endian warning in __ip_do_redirect
+    - net: usb: ax88179_178a: fix failed operations during ax88179_reset
+    - net/smc: avoid data corruption caused by decline
+    - arm/xen: fix xen_vcpu_info allocation alignment
+    - octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx
+      queue than its PF
+    - amd-xgbe: handle corner-case during sfp hotplug
+    - amd-xgbe: handle the corner-case during tx completion
+    - amd-xgbe: propagate the correct speed and duplex status
+    - net: axienet: Fix check for partial TX checksum
+    - afs: Return ENOENT if no cell DNS record can be found
+    - afs: Fix file locking on R/O volumes to operate in local mode
+    - nvmet: nul-terminate the NQNs passed in the connect command
+    - USB: dwc3: qcom: fix resource leaks on probe deferral
+    - USB: dwc3: qcom: fix ACPI platform device leak
+    - lockdep: Fix block chain corruption
+    - MIPS: KVM: Fix a build warning about variable set but not used
+    - media: camss: Replace hard coded value with parameter
+    - media: camss: sm8250: Virtual channels for CSID
+    - media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3
+    - media: qcom: camss: Fix csid-gen2 for test pattern generator
+    - ext4: add a new helper to check if es must be kept
+    - ext4: factor out __es_alloc_extent() and __es_free_extent()
+    - ext4: use pre-allocated es in __es_insert_extent()
+    - ext4: use pre-allocated es in __es_remove_extent()
+    - ext4: using nofail preallocation in ext4_es_remove_extent()
+    - ext4: using nofail preallocation in ext4_es_insert_delayed_block()
+    - ext4: using nofail preallocation in ext4_es_insert_extent()
+    - ext4: fix slab-use-after-free in ext4_es_insert_extent()
+    - ext4: make sure allocate pending entry not fail
+    - proc: sysctl: prevent aliased sysctls from getting passed to init
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CVA
+    - swiotlb-xen: provide the "max_mapping_size" method
+    - bcache: replace a mistaken IS_ERR() by IS_ERR_OR_NULL() in
+      btree_gc_coalesce()
+    - md: fix bi_status reporting in md_end_clone_io
+    - bcache: fixup multi-threaded bch_sectors_dirty_init() wake-up race
+    - io_uring/fs: consider link->flags when getting path for LINKAT
+    - s390/dasd: protect device queue against concurrent access
+    - USB: serial: option: add Luat Air72*U series products
+    - hv_netvsc: Fix race of register_netdevice_notifier and VF register
+    - hv_netvsc: Mark VF as slave before exposing it to user-mode
+    - dm-delay: fix a race between delay_presuspend and delay_bio
+    - bcache: check return value from btree_node_alloc_replacement()
+    - bcache: prevent potential division by zero error
+    - bcache: fixup init dirty data errors
+    - bcache: fixup lock c->root error
+    - usb: cdnsp: Fix deadlock issue during using NCM gadget
+    - USB: serial: option: add Fibocom L7xx modules
+    - USB: serial: option: fix FM101R-GL defines
+    - USB: serial: option: don't claim interface 4 for ZTE MF290
+    - usb: typec: tcpm: Skip hard reset when in error recovery
+    - USB: dwc2: write HCINT with INTMASK applied
+    - usb: dwc3: Fix default mode initialization
+    - usb: dwc3: set the dma max_seg_size
+    - USB: dwc3: qcom: fix software node leak on probe errors
+    - USB: dwc3: qcom: fix wakeup after probe deferral
+    - io_uring: fix off-by one bvec index
+    - Linux 5.15.141
+  * Jammy update: v5.15.140 upstream stable release (LP: #2050038)
+    - locking/ww_mutex/test: Fix potential workqueue corruption
+    - perf/core: Bail out early if the request AUX area is out of bound
+    - clocksource/drivers/timer-imx-gpt: Fix potential memory leak
+    - clocksource/drivers/timer-atmel-tcb: Fix initialization on SAM9 hardware
+    - workqueue: Provide one lock class key per work_on_cpu() callsite
+    - x86/mm: Drop the 4 MB restriction on minimal NUMA node memory size
+    - wifi: mac80211_hwsim: fix clang-specific fortify warning
+    - wifi: mac80211: don't return unset power in ieee80211_get_tx_power()
+    - atl1c: Work around the DMA RX overflow issue
+    - bpf: Detect IP == ksym.end as part of BPF program
+    - wifi: ath9k: fix clang-specific fortify warnings
+    - wifi: ath10k: fix clang-specific fortify warning
+    - net: annotate data-races around sk->sk_tx_queue_mapping
+    - net: annotate data-races around sk->sk_dst_pending_confirm
+    - wifi: ath10k: Don't touch the CE interrupt registers after power up
+    - Bluetooth: btusb: Add date->evt_skb is NULL check
+    - Bluetooth: Fix double free in hci_conn_cleanup
+    - platform/x86: thinkpad_acpi: Add battery quirk for Thinkpad X120e
+    - drm/komeda: drop all currently held locks if deadlock happens
+    - drm/amdkfd: Fix a race condition of vram buffer unref in svm code
+    - drm/amd/display: use full update for clip size increase of large plane
+      source
+    - string.h: add array-wrappers for (v)memdup_user()
+    - kernel: kexec: copy user-array safely
+    - kernel: watch_queue: copy user-array safely
+    - drm: vmwgfx_surface.c: copy user-array safely
+    - drm/msm/dp: skip validity check for DP CTS EDID checksum
+    - drm/amd: Fix UBSAN array-index-out-of-bounds for SMU7
+    - drm/amd: Fix UBSAN array-index-out-of-bounds for Polaris and Tonga
+    - drm/amdgpu: Fix potential null pointer derefernce
+    - drm/panel: fix a possible null pointer dereference
+    - drm/panel/panel-tpo-tpg110: fix a possible null pointer dereference
+    - drm/amdgpu/vkms: fix a possible null pointer dereference
+    - drm/panel: st7703: Pick different reset sequence
+    - drm/amdkfd: Fix shift out-of-bounds issue
+    - drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL
+    - arm64: dts: ls208xa: use a pseudo-bus to constrain usb dma size
+    - selftests/efivarfs: create-read: fix a resource leak
+    - ASoC: soc-card: Add storage for PCI SSID
+    - crypto: pcrypt - Fix hungtask for PADATA_RESET
+    - RDMA/hfi1: Use FIELD_GET() to extract Link Width
+    - scsi: hisi_sas: Set debugfs_dir pointer to NULL after removing debugfs
+    - scsi: ibmvfc: Remove BUG_ON in the case of an empty event pool
+    - fs/jfs: Add check for negative db_l2nbperpage
+    - fs/jfs: Add validity check for db_maxag and db_agpref
+    - jfs: fix array-index-out-of-bounds in dbFindLeaf
+    - jfs: fix array-index-out-of-bounds in diAlloc
+    - HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround
+    - ARM: 9320/1: fix stack depot IRQ stack filter
+    - ALSA: hda: Fix possible null-ptr-deref when assigning a stream
+    - PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields
+    - atm: iphase: Do PCI error checks on own line
+    - scsi: libfc: Fix potential NULL pointer dereference in fc_lport_ptp_setup()
+    - PCI: Use FIELD_GET() to extract Link Width
+    - PCI: Extract ATS disabling to a helper function
+    - PCI: Disable ATS for specific Intel IPU E2000 devices
+    - misc: pci_endpoint_test: Add Device ID for R-Car S4-8 PCIe controller
+    - PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk
+    - HID: Add quirk for Dell Pro Wireless Keyboard and Mouse KM5221W
+    - exfat: support handle zero-size directory
+    - tty: vcc: Add check for kstrdup() in vcc_probe()
+    - usb: gadget: f_ncm: Always set current gadget in ncm_bind()
+    - 9p/trans_fd: Annotate data-racy writes to file::f_flags
+    - 9p: v9fs_listxattr: fix %s null argument warning
+    - i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
+    - i2c: sun6i-p2wi: Prevent potential division by zero
+    - virtio-blk: fix implicit overflow on virtio_max_dma_size
+    - i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
+    - media: gspca: cpia1: shift-out-of-bounds in set_flicker
+    - media: vivid: avoid integer overflow
+    - gfs2: ignore negated quota changes
+    - gfs2: fix an oops in gfs2_permission
+    - media: cobalt: Use FIELD_GET() to extract Link Width
+    - media: ccs: Fix driver quirk struct documentation
+    - media: imon: fix access to invalid resource for the second interface
+    - drm/amd/display: Avoid NULL dereference of timing generator
+    - kgdb: Flush console before entering kgdb on panic
+    - i2c: dev: copy userspace array safely
+    - ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
+    - drm/qxl: prevent memory leak
+    - drm/amdgpu: fix software pci_unplug on some chips
+    - pwm: Fix double shift bug
+    - wifi: iwlwifi: Use FW rate for non-data frames
+    - tracing: Reuse logic from perf's get_recursion_context()
+    - tracing/perf: Add interrupt_context_level() helper
+    - sched/core: Optimize in_task() and in_interrupt() a bit
+    - media: cadence: csi2rx: Unregister v4l2 async notifier
+    - media: cec: meson: always include meson sub-directory in Makefile
+    - SUNRPC: ECONNRESET might require a rebind
+    - SUNRPC: Add an IS_ERR() check back to where it was
+    - NFSv4.1: fix SP4_MACH_CRED protection for pnfs IO
+    - SUNRPC: Fix RPC client cleaned up the freed pipefs dentries
+    - gfs2: Silence "suspicious RCU usage in gfs2_permission" warning
+    - mptcp: diag: switch to context structure
+    - mptcp: listen diag dump support
+    - net: inet: Remove count from inet_listen_hashbucket
+    - net: inet: Open code inet_hash2 and inet_unhash2
+    - net: inet: Retire port only listening_hash
+    - net: set SOCK_RCU_FREE before inserting socket into hashtable
+    - ipvlan: add ipvlan_route_v6_outbound() helper
+    - tty: Fix uninit-value access in ppp_sync_receive()
+    - net: hns3: fix add VLAN fail issue
+    - net: hns3: refine the definition for struct hclge_pf_to_vf_msg
+    - net: hns3: add byte order conversion for PF to VF mailbox message
+    - net: hns3: add barrier in vf mailbox reply process
+    - net: hns3: fix incorrect capability bit display for copper port
+    - net: hns3: fix variable may not initialized problem in hns3_init_mac_addr()
+    - net: hns3: fix VF reset fail issue
+    - net: hns3: fix VF wrong speed and duplex issue
+    - tipc: Fix kernel-infoleak due to uninitialized TLV value
+    - ppp: limit MRU to 64K
+    - xen/events: fix delayed eoi list handling
+    - ptp: annotate data-race around q->head and q->tail
+    - bonding: stop the device in bond_setup_by_slave()
+    - net: ethernet: cortina: Fix max RX frame define
+    - net: ethernet: cortina: Handle large frames
+    - net: ethernet: cortina: Fix MTU max setting
+    - af_unix: fix use-after-free in unix_stream_read_actor()
+    - netfilter: nf_conntrack_bridge: initialize err to 0
+    - netfilter: nf_tables: use the correct get/put helpers
+    - netfilter: nf_tables: add and use BE register load-store helpers
+    - netfilter: nf_tables: fix pointer math issue in nft_byteorder_eval()
+    - net: stmmac: fix rx budget limit check
+    - net/mlx5e: Remove incorrect addition of action fwd flag
+    - net/mlx5e: Move mod hdr allocation to a single place
+    - net/mlx5e: Refactor mod header management API
+    - net/mlx5e: Fix pedit endianness
+    - net/mlx5e: Reduce the size of icosq_str
+    - net/mlx5e: Check return value of snprintf writing to fw_version buffer for
+      representors
+    - macvlan: Don't propagate promisc change to lower dev in passthru
+    - tools/power/turbostat: Fix a knl bug
+    - tools/power/turbostat: Enable the C-state Pre-wake printing
+    - cifs: spnego: add ';' in HOST_KEY_LEN
+    - cifs: fix check of rc in function generate_smb3signingkey
+    - xfs: refactor buffer cancellation table allocation
+    - xfs: don't leak xfs_buf_cancel structures when recovery fails
+    - xfs: convert buf_cancel_table allocation to kmalloc_array
+    - xfs: use invalidate_lock to check the state of mmap_lock
+    - xfs: prevent a UAF when log IO errors race with unmount
+    - xfs: flush inode gc workqueue before clearing agi bucket
+    - xfs: fix use-after-free in xattr node block inactivation
+    - xfs: don't leak memory when attr fork loading fails
+    - xfs: fix intermittent hang during quotacheck
+    - xfs: add missing cmap->br_state = XFS_EXT_NORM update
+    - xfs: Fix false ENOSPC when performing direct write on a delalloc extent in
+      cow fork
+    - xfs: fix inode reservation space for removing transaction
+    - xfs: avoid a UAF when log intent item recovery fails
+    - xfs: fix exception caused by unexpected illegal bestcount in leaf dir
+    - xfs: fix memory leak in xfs_errortag_init
+    - xfs: Fix unreferenced object reported by kmemleak in xfs_sysfs_init()
+    - i915/perf: Fix NULL deref bugs with drm_dbg() calls
+    - media: venus: hfi: add checks to perform sanity on queue pointers
+    - powerpc/perf: Fix disabling BHRB and instruction sampling
+    - randstruct: Fix gcc-plugin performance mode to stay in group
+    - bpf: Fix check_stack_write_fixed_off() to correctly spill imm
+    - bpf: Fix precision tracking for BPF_ALU | BPF_TO_BE | BPF_END
+    - scsi: mpt3sas: Fix loop logic
+    - scsi: megaraid_sas: Increase register read retry rount from 3 to 30 for
+      selected registers
+    - scsi: qla2xxx: Fix system crash due to bad pointer access
+    - crypto: x86/sha - load modules based on CPU features
+    - x86/cpu/hygon: Fix the CPU topology evaluation for real
+    - KVM: x86: hyper-v: Don't auto-enable stimer on write from user-space
+    - KVM: x86: Ignore MSR_AMD64_TW_CFG access
+    - audit: don't take task_lock() in audit_exe_compare() code path
+    - audit: don't WARN_ON_ONCE(!current->mm) in audit_exe_compare()
+    - tty/sysrq: replace smp_processor_id() with get_cpu()
+    - hvc/xen: fix console unplug
+    - hvc/xen: fix error path in xen_hvc_init() to always register frontend driver
+    - hvc/xen: fix event channel handling for secondary consoles
+    - PCI/sysfs: Protect driver's D3cold preference from user space
+    - watchdog: move softlockup_panic back to early_param
+    - ACPI: resource: Do IRQ override on TongFang GMxXGxx
+    - arm64: Restrict CPU_BIG_ENDIAN to GNU as or LLVM IAS 15.x or newer
+    - parisc/pdc: Add width field to struct pdc_model
+    - clk: socfpga: Fix undefined behavior bug in struct stratix10_clock_data
+    - clk: qcom: ipq8074: drop the CLK_SET_RATE_PARENT flag from PLL clocks
+    - clk: qcom: ipq6018: drop the CLK_SET_RATE_PARENT flag from PLL clocks
+    - mmc: vub300: fix an error code
+    - mmc: sdhci_am654: fix start loop index for TAP value parsing
+    - PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
+    - PCI: exynos: Don't discard .remove() callback
+    - wifi: wilc1000: use vmm_table as array in wilc struct
+    - svcrdma: Drop connection after an RDMA Read error
+    - rcu/tree: Defer setting of jiffies during stall reset
+    - arm64: dts: qcom: ipq6018: Fix hwlock index for SMEM
+    - PM: hibernate: Use __get_safe_page() rather than touching the list
+    - PM: hibernate: Clean up sync_read handling in snapshot_write_next()
+    - rcu: kmemleak: Ignore kmemleak false positives when RCU-freeing objects
+    - btrfs: don't arbitrarily slow down delalloc if we're committing
+    - firmware: qcom_scm: use 64-bit calling convention only when client is 64-bit
+    - ACPI: FPDT: properly handle invalid FPDT subtables
+    - ima: annotate iint mutex to avoid lockdep false positive warnings
+    - ima: detect changes to the backing overlay file
+    - wifi: ath11k: fix temperature event locking
+    - wifi: ath11k: fix dfs radar event locking
+    - wifi: ath11k: fix htt pktlog locking
+    - mmc: meson-gx: Remove setting of CMD_CFG_ERROR
+    - genirq/generic_chip: Make irq_remove_generic_chip() irqdomain aware
+    - KEYS: trusted: Rollback init_trusted() consistently
+    - PCI: keystone: Don't discard .remove() callback
+    - PCI: keystone: Don't discard .probe() callback
+    - netfilter: nf_tables: split async and sync catchall in two functions
+    - selftests/resctrl: Remove duplicate feature check from CMT test
+    - selftests/resctrl: Reduce failures due to outliers in MBA/MBM tests
+    - ASoC: codecs: wsa-macro: fix uninitialized stack variables with name prefix
+    - jbd2: fix potential data lost in recovering journal raced with synchronizing
+      fs bdev
+    - quota: explicitly forbid quota files from being encrypted
+    - kernel/reboot: emergency_restart: Set correct system_state
+    - i2c: core: Run atomic i2c xfer when !preemptible
+    - tracing: Have the user copy of synthetic event address use correct context
+    - mcb: fix error handling for different scenarios when parsing
+    - dmaengine: stm32-mdma: correct desc prep when channel running
+    - s390/cmma: fix detection of DAT pages
+    - mm/cma: use nth_page() in place of direct struct page manipulation
+    - mm/memory_hotplug: use pfn math in place of direct struct page manipulation
+    - mtd: cfi_cmdset_0001: Byte swap OTP info
+    - i3c: master: cdns: Fix reading status register
+    - i3c: master: svc: fix race condition in ibi work thread
+    - i3c: master: svc: fix wrong data return when IBI happen during start frame
+    - i3c: master: svc: fix ibi may not return mandatory data byte
+    - i3c: master: svc: fix check wrong status register in irq handler
+    - i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
+    - parisc: Prevent booting 64-bit kernels on PA1.x machines
+    - parisc/pgtable: Do not drop upper 5 address bits of physical address
+    - xhci: Enable RPM on controllers that support low-power states
+    - ALSA: info: Fix potential deadlock at disconnection
+    - ALSA: hda/realtek - Add Dell ALC295 to pin fall back table
+    - ALSA: hda/realtek - Enable internal speaker of ASUS K6500ZC
+    - serial: meson: Use platform_get_irq() to get the interrupt
+    - tty: serial: meson: fix hard LOCKUP on crtscts mode
+    - regmap: Ensure range selector registers are updated after cache sync
+    - cpufreq: stats: Fix buffer overflow detection in trans_stats()
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0cb8:0xc559
+    - bluetooth: Add device 0bda:887b to device tables
+    - bluetooth: Add device 13d3:3571 to device tables
+    - Bluetooth: btusb: Add RTW8852BE device 13d3:3570 to device tables
+    - Bluetooth: btusb: Add 0bda:b85b for Fn-Link RTL8852BE
+    - ksmbd: fix slab out of bounds write in smb_inherit_dacl()
+    - arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
+    - arm64: dts: qcom: ipq6018: Fix tcsr_mutex register size
+    - powerpc/pseries/ddw: simplify enable_ddw()
+    - Revert ncsi: Propagate carrier gain/loss events to the NCSI controller
+    - Revert "i2c: pxa: move to generic GPIO recovery"
+    - lsm: fix default return value for vm_enough_memory
+    - lsm: fix default return value for inode_getsecctx
+    - sbsa_gwdt: Calculate timeout with 64-bit math
+    - i2c: designware: Disable TX_EMPTY irq while waiting for block length byte
+    - s390/ap: fix AP bus crash on early config change callback invocation
+    - net: ethtool: Fix documentation of ethtool_sprintf()
+    - net: dsa: lan9303: consequently nested-lock physical MDIO
+    - net: phylink: initialize carrier state at creation
+    - i2c: i801: fix potential race in i801_block_transaction_byte_by_byte
+    - f2fs: avoid format-overflow warning
+    - media: lirc: drop trailing space from scancode transmit
+    - media: sharp: fix sharp encoding
+    - media: venus: hfi_parser: Add check to keep the number of codecs within
+      range
+    - media: venus: hfi: fix the check to handle session buffer requirement
+    - media: venus: hfi: add checks to handle capabilities from firmware
+    - media: ccs: Correctly initialise try compose rectangle
+    - nfsd: fix file memleak on client_opens_release
+    - riscv: kprobes: allow writing to x0
+    - mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2
+    - mm: kmem: drop __GFP_NOFAIL when allocating objcg vectors
+    - r8169: fix network lost after resume on DASH systems
+    - mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of AER
+    - media: qcom: camss: Fix pm_domain_on sequence in probe
+    - media: qcom: camss: Fix vfe_get() error jump
+    - media: qcom: camss: Fix VFE-17x vfe_disable_output()
+    - media: qcom: camss: Fix missing vfe_lite clocks check
+    - ext4: apply umask if ACL support is disabled
+    - ext4: correct offset of gdb backup in non meta_bg group to update_backups
+    - ext4: correct return value of ext4_convert_meta_bg
+    - ext4: correct the start block of counting reserved clusters
+    - ext4: remove gdb backup copy for meta bg in setup_new_flex_group_blocks
+    - ext4: add missed brelse in update_backups
+    - drm/amd/pm: Handle non-terminated overdrive commands.
+    - drm/i915: Fix potential spectre vulnerability
+    - drm/amdgpu: don't use ATRM for external devices
+    - drm/amdgpu: fix error handling in amdgpu_bo_list_get()
+    - drm/amd/display: Change the DMCUB mailbox memory location from FB to inbox
+    - powerpc/powernv: Fix fortify source warnings in opal-prd.c
+    - tracing: Have trace_event_file have ref counters
+    - Input: xpad - add VID for Turtle Beach controllers
+    - driver core: Release all resources during unbind before updating device
+      links
+    - Linux 5.15.140
+  * CVE-2023-46862
+    - io_uring/fdinfo: lock SQ thread while retrieving thread cpu/pid
+  * Jammy update: v5.15.139 upstream stable release (LP: #2049432)
+    - iov_iter, x86: Be consistent about the __user tag on copy_mc_to_user()
+    - sched/uclamp: Ignore (util == 0) optimization in feec() when p_util_max = 0
+    - sched: Fix stop_one_cpu_nowait() vs hotplug
+    - vfs: fix readahead(2) on block devices
+    - writeback, cgroup: switch inodes with dirty timestamps to release dying
+      cgwbs
+    - x86/srso: Fix SBPB enablement for (possible) future fixed HW
+    - futex: Don't include process MM in futex key on no-MMU
+    - x86: Share definition of __is_canonical_address()
+    - x86/sev-es: Allow copy_from_kernel_nofault() in earlier boot
+    - x86/boot: Fix incorrect startup_gdt_descr.size
+    - pstore/platform: Add check for kstrdup
+    - genirq/matrix: Exclude managed interrupts in irq_matrix_allocated()
+    - i40e: fix potential memory leaks in i40e_remove()
+    - selftests/bpf: Test tail call counting with bpf2bpf and data on stack
+    - selftests/bpf: Correct map_fd to data_fd in tailcalls
+    - udp: add missing WRITE_ONCE() around up->encap_rcv
+    - tcp: call tcp_try_undo_recovery when an RTOd TFO SYNACK is ACKed
+    - gve: Use size_add() in call to struct_size()
+    - mlxsw: Use size_mul() in call to struct_size()
+    - tipc: Use size_add() in calls to struct_size()
+    - net: spider_net: Use size_add() in call to struct_size()
+    - wifi: rtw88: debug: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
+    - wifi: mt76: mt7603: rework/fix rx pse hang check
+    - mt76: dma: use kzalloc instead of devm_kzalloc for txwi
+    - mt76: add support for overriding the device used for DMA mapping
+    - mt76: pass original queue id from __mt76_tx_queue_skb to the driver
+    - wifi: mt76: mt7603: improve stuck beacon handling
+    - tcp_metrics: add missing barriers on delete
+    - tcp_metrics: properly set tp->snd_ssthresh in tcp_init_metrics()
+    - tcp_metrics: do not create an entry from tcp_init_metrics()
+    - wifi: rtlwifi: fix EDCA limit set by BT coexistence
+    - can: dev: can_restart(): don't crash kernel if carrier is OK
+    - can: dev: can_restart(): fix race condition between controller restart and
+      netif_carrier_on()
+    - can: dev: can_put_echo_skb(): don't crash kernel if can_priv::echo_skb is
+      accessed out of bounds
+    - PM / devfreq: rockchip-dfi: Make pmu regmap mandatory
+    - netfilter: nf_tables: Drop pointless memset when dumping rules
+    - thermal: core: prevent potential string overflow
+    - r8169: use tp_to_dev instead of open code
+    - r8169: fix rare issue with broken rx after link-down on RTL8125
+    - chtls: fix tp->rcv_tstamp initialization
+    - tcp: fix cookie_init_timestamp() overflows
+    - iwlwifi: pcie: adjust to Bz completion descriptor
+    - wifi: iwlwifi: call napi_synchronize() before freeing rx/tx queues
+    - wifi: iwlwifi: pcie: synchronize IRQs before NAPI
+    - wifi: iwlwifi: empty overflow queue during flush
+    - ACPI: sysfs: Fix create_pnp_modalias() and create_of_modalias()
+    - ipv6: avoid atomic fragment on GSO packets
+    - net: add DEV_STATS_READ() helper
+    - ipvlan: properly track tx_errors
+    - regmap: debugfs: Fix a erroneous check after snprintf()
+    - spi: tegra: Fix missing IRQ check in tegra_slink_probe()
+    - clk: qcom: clk-rcg2: Fix clock rate overflow for high parent frequencies
+    - clk: qcom: mmcc-msm8998: Don't check halt bit on some branch clks
+    - clk: qcom: mmcc-msm8998: Fix the SMMU GDSC
+    - clk: qcom: gcc-sm8150: Fix gcc_sdcc2_apps_clk_src
+    - clk: imx: Select MXC_CLK for CLK_IMX8QXP
+    - clk: imx: imx8mq: correct error handling path
+    - clk: imx: imx8qxp: Fix elcdif_pll clock
+    - clk: renesas: rzg2l: Simplify multiplication/shift logic
+    - clk: renesas: rzg2l: Use FIELD_GET() for PLL register fields
+    - clk: renesas: rzg2l: Fix computation formula
+    - spi: nxp-fspi: use the correct ioremap function
+    - clk: keystone: pll: fix a couple NULL vs IS_ERR() checks
+    - clk: ti: Add ti_dt_clk_name() helper to use clock-output-names
+    - clk: ti: Update pll and clockdomain clocks to use ti_dt_clk_name()
+    - clk: ti: Update component clocks to use ti_dt_clk_name()
+    - clk: ti: change ti_clk_register[_omap_hw]() API
+    - clk: ti: fix double free in of_ti_divider_clk_setup()
+    - clk: npcm7xx: Fix incorrect kfree
+    - clk: mediatek: clk-mt6765: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt6797: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt7629-eth: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt7629: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt2701: Add check for mtk_alloc_clk_data
+    - clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM
+    - platform/x86: wmi: Fix probe failure when failing to register WMI devices
+    - platform/x86: wmi: remove unnecessary initializations
+    - platform/x86: wmi: Fix opening of char device
+    - hwmon: (axi-fan-control) Fix possible NULL pointer dereference
+    - hwmon: (coretemp) Fix potentially truncated sysfs attribute name
+    - drm/rockchip: vop: Fix reset of state in duplicate state crtc funcs
+    - drm/rockchip: vop: Fix call to crtc reset helper
+    - drm/radeon: possible buffer overflow
+    - drm/mipi-dsi: Create devm device registration
+    - drm/mipi-dsi: Create devm device attachment
+    - drm/bridge: lt8912b: Switch to devm MIPI-DSI helpers
+    - drm/bridge: lt8912b: Register and attach our DSI device at probe
+    - drm/bridge: lt8912b: Add hot plug detection
+    - drm/bridge: lt8912b: Fix bridge_detach
+    - drm/bridge: lt8912b: Fix crash on bridge detach
+    - drm/bridge: lt8912b: Manually disable HPD only if it was enabled
+    - drm/bridge: lt8912b: Add missing drm_bridge_attach call
+    - drm/bridge: tc358768: Fix use of uninitialized variable
+    - drm/bridge: tc358768: Disable non-continuous clock mode
+    - drm/bridge: tc358768: Fix bit updates
+    - drm/amdkfd: fix some race conditions in vram buffer alloc/free of svm code
+    - drm/mediatek: Fix iommu fault by swapping FBs after updating plane state
+    - drm/mediatek: Fix iommu fault during crtc enabling
+    - drm/rockchip: cdn-dp: Fix some error handling paths in cdn_dp_probe()
+    - arm64/arm: xen: enlighten: Fix KPTI checks
+    - drm/rockchip: Fix type promotion bug in rockchip_gem_iommu_map()
+    - xen-pciback: Consider INTx disabled when MSI/MSI-X is enabled
+    - drm/msm/dsi: use msm_gem_kernel_put to free TX buffer
+    - drm: mediatek: mtk_dsi: Fix NO_EOT_PACKET settings/handling
+    - perf: hisi: Fix use-after-free when register pmu fails
+    - ARM: dts: renesas: blanche: Fix typo in GP_11_2 pin name
+    - arm64: dts: qcom: msm8916: Fix iommu local address range
+    - arm64: dts: qcom: msm8992-libra: drop duplicated reserved memory
+    - arm64: dts: qcom: sc7280: Add missing LMH interrupts
+    - arm64: dts: qcom: sdm845-mtp: fix WiFi configuration
+    - ARM64: dts: marvell: cn9310: Use appropriate label for spi1 pins
+    - arm64: dts: qcom: apq8016-sbc: Add missing ADV7533 regulators
+    - ARM: dts: qcom: mdm9615: populate vsdcc fixed regulator
+    - soc: qcom: llcc: Handle a second device without data corruption
+    - firmware: ti_sci: Mark driver as non removable
+    - firmware: arm_ffa: Assign the missing IDR allocation ID to the FFA device
+    - clk: scmi: Free scmi_clk allocated when the clocks with invalid info are
+      skipped
+    - arm64: dts: imx8qm-ss-img: Fix jpegenc compatible entry
+    - arm64: dts: imx8mm: Add sound-dai-cells to micfil node
+    - arm64: dts: imx8mn: Add sound-dai-cells to micfil node
+    - selftests/pidfd: Fix ksft print formats
+    - selftests/resctrl: Ensure the benchmark commands fits to its array
+    - crypto: hisilicon/hpre - Fix a erroneous check after snprintf()
+    - hwrng: geode - fix accessing registers
+    - RDMA/core: Use size_{add,sub,mul}() in calls to struct_size()
+    - scsi: ibmvfc: Fix erroneous use of rtas_busy_delay with hcall return code
+    - libnvdimm/of_pmem: Use devm_kstrdup instead of kstrdup and check its return
+      value
+    - nd_btt: Make BTT lanes preemptible
+    - crypto: caam/qi2 - fix Chacha20 + Poly1305 self test failure
+    - crypto: caam/jr - fix Chacha20 + Poly1305 self test failure
+    - crypto: qat - increase size of buffers
+    - hid: cp2112: Fix duplicate workqueue initialization
+    - ARM: 9321/1: memset: cast the constant byte to unsigned char
+    - ext4: move 'ix' sanity check to corrent position
+    - ASoC: fsl: mpc5200_dma.c: Fix warning of Function parameter or member not
+      described
+    - IB/mlx5: Fix rdma counter binding for RAW QP
+    - RDMA/hns: Fix uninitialized ucmd in hns_roce_create_qp_common()
+    - RDMA/hns: Fix signed-unsigned mixed comparisons
+    - RDMA/hns: The UD mode can only be configured with DCQCN
+    - ASoC: fsl: Fix PM disable depth imbalance in fsl_easrc_probe
+    - scsi: ufs: core: Leave space for '\0' in utf8 desc string
+    - RDMA/hfi1: Workaround truncation compilation error
+    - hid: cp2112: Fix IRQ shutdown stopping polling for all IRQs on chip
+    - sh: bios: Revive earlyprintk support
+    - Revert "HID: logitech-hidpp: add a module parameter to keep firmware
+      gestures"
+    - HID: logitech-hidpp: Remove HIDPP_QUIRK_NO_HIDINPUT quirk
+    - HID: logitech-hidpp: Don't restart IO, instead defer hid_connect() only
+    - HID: logitech-hidpp: Revert "Don't restart communication if not necessary"
+    - HID: logitech-hidpp: Move get_wireless_feature_index() check to
+      hidpp_connect_event()
+    - ASoC: Intel: Skylake: Fix mem leak when parsing UUIDs fails
+    - padata: Fix refcnt handling in padata_free_shell()
+    - crypto: qat - fix deadlock in backlog processing
+    - ASoC: ams-delta.c: use component after check
+    - mfd: core: Un-constify mfd_cell.of_reg
+    - mfd: core: Ensure disabled devices are skipped without aborting
+    - mfd: dln2: Fix double put in dln2_probe
+    - mfd: arizona-spi: Set pdata.hpdet_channel for ACPI enumerated devs
+    - leds: turris-omnia: Drop unnecessary mutex locking
+    - leds: turris-omnia: Do not use SMBUS calls
+    - leds: pwm: Don't disable the PWM when the LED should be off
+    - leds: trigger: ledtrig-cpu:: Fix 'output may be truncated' issue for 'cpu'
+    - f2fs: compress: fix to avoid use-after-free on dic
+    - f2fs: compress: fix to avoid redundant compress extension
+    - tty: tty_jobctrl: fix pid memleak in disassociate_ctty()
+    - livepatch: Fix missing newline character in klp_resolve_symbols()
+    - dmaengine: idxd: Register dsa_bus_type before registering idxd sub-drivers
+    - usb: dwc2: fix possible NULL pointer dereference caused by driver
+      concurrency
+    - usb: chipidea: Fix DMA overwrite for Tegra
+    - usb: chipidea: Simplify Tegra DMA alignment code
+    - dmaengine: ti: edma: handle irq_of_parse_and_map() errors
+    - misc: st_core: Do not call kfree_skb() under spin_lock_irqsave()
+    - tools: iio: iio_generic_buffer ensure alignment
+    - USB: usbip: fix stub_dev hub disconnect
+    - dmaengine: pxa_dma: Remove an erroneous BUG_ON() in pxad_free_desc()
+    - f2fs: fix to initialize map.m_pblk in f2fs_precache_extents()
+    - powerpc: Only define __parse_fpscr() when required
+    - modpost: fix tee MODULE_DEVICE_TABLE built on big-endian host
+    - powerpc/40x: Remove stale PTE_ATOMIC_UPDATES macro
+    - powerpc/xive: Fix endian conversion size
+    - powerpc/imc-pmu: Use the correct spinlock initializer.
+    - powerpc/pseries: fix potential memory leak in init_cpu_associativity()
+    - usb: host: xhci-plat: fix possible kernel oops while resuming
+    - perf machine: Avoid out of bounds LBR memory read
+    - perf hist: Add missing puts to hist__account_cycles
+    - 9p/net: fix possible memory leak in p9_check_errors()
+    - i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
+    - cxl/mem: Fix shutdown order
+    - rtc: pcf85363: fix wrong mask/val parameters in regmap_update_bits call
+    - pcmcia: cs: fix possible hung task and memory leak pccardd()
+    - pcmcia: ds: fix refcount leak in pcmcia_device_add()
+    - pcmcia: ds: fix possible name leak in error path in pcmcia_device_add()
+    - media: i2c: max9286: Fix some redundant of_node_put() calls
+    - media: bttv: fix use after free error due to btv->timeout timer
+    - media: s3c-camif: Avoid inappropriate kfree()
+    - media: vidtv: psi: Add check for kstrdup
+    - media: vidtv: mux: Add check and kfree for kstrdup
+    - media: cedrus: Fix clock/reset sequence
+    - media: dvb-usb-v2: af9035: fix missing unlock
+    - regmap: prevent noinc writes from clobbering cache
+    - pwm: sti: Reduce number of allocations and drop usage of chip_data
+    - pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
+    - Input: synaptics-rmi4 - fix use after free in rmi_unregister_function()
+    - llc: verify mac len before reading mac header
+    - hsr: Prevent use after free in prp_create_tagged_frame()
+    - tipc: Change nla_policy for bearer-related names to NLA_NUL_STRING
+    - bpf: Check map->usercnt after timer->timer is assigned
+    - inet: shrink struct flowi_common
+    - octeontx2-pf: Fix error codes
+    - octeontx2-pf: Fix holes in error code
+    - dccp: Call security_inet_conn_request() after setting IPv4 addresses.
+    - dccp/tcp: Call security_inet_conn_request() after setting IPv6 addresses.
+    - Fix termination state for idr_for_each_entry_ul()
+    - net: stmmac: xgmac: Enable support for multiple Flexible PPS outputs
+    - selftests: pmtu.sh: fix result checking
+    - net/smc: fix dangling sock under state SMC_APPFINCLOSEWAIT
+    - net/smc: allow cdc msg send rather than drop it with NULL sndbuf_desc
+    - net/smc: put sk reference if close work was canceled
+    - tg3: power down device only on SYSTEM_POWER_OFF
+    - block: remove unneeded return value of bio_check_ro()
+    - blk-core: use pr_warn_ratelimited() in bio_check_ro()
+    - r8169: respect userspace disabling IFF_MULTICAST
+    - i2c: iproc: handle invalid slave state
+    - netfilter: xt_recent: fix (increase) ipv6 literal buffer length
+    - netfilter: nft_redir: use `struct nf_nat_range2` throughout and deduplicate
+      eval call-backs
+    - netfilter: nat: fix ipv6 nat redirect with mapped and scoped addresses
+    - drm/syncobj: fix DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE
+    - ASoC: hdmi-codec: register hpd callback on component probe
+    - spi: spi-zynq-qspi: add spi-mem to driver kconfig dependencies
+    - fbdev: imsttfb: Fix error path of imsttfb_probe()
+    - fbdev: imsttfb: fix a resource leak in probe
+    - fbdev: fsl-diu-fb: mark wr_reg_wa() static
+    - tracing/kprobes: Fix the order of argument descriptions
+    - btrfs: use u64 for buffer sizes in the tree search ioctls
+    - Linux 5.15.139
+  * Jammy update: v5.15.138 upstream stable release (LP: #2049417)
+    - ASoC: codecs: wcd938x: fix resource leaks on bind errors
+    - ASoC: codecs: wcd938x: fix runtime PM imbalance on remove
+    - pinctrl: qcom: lpass-lpi: fix concurrent register updates
+    - tcp: remove dead code from tcp_sendmsg_locked()
+    - tcp: cleanup tcp_remove_empty_skb() use
+    - mptcp: more conservative check for zero probes
+    - mcb: Return actual parsed size when reading chameleon table
+    - mcb-lpc: Reallocate memory region to avoid memory overlapping
+    - virtio_balloon: Fix endless deflation and inflation on arm64
+    - virtio-mmio: fix memory leak of vm_dev
+    - vhost: Allow null msg.size on VHOST_IOTLB_INVALIDATE
+    - mm/page_alloc: correct start page when guard page debug is enabled
+    - mm/migrate: fix do_pages_move for compat pointers
+    - nfsd: lock_rename() needs both directories to live on the same fs
+    - drm/i915/pmu: Check if pmu is closed before stopping event
+    - vsock/virtio: factor our the code to initialize and delete VQs
+    - vsock/virtio: add support for device suspend/resume
+    - vsock/virtio: initialize the_virtio_vsock before using VQs
+    - drm/dp_mst: Fix NULL deref in get_mst_branch_device_by_guid_helper()
+    - firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels()
+    - r8169: fix the KCSAN reported data-race in rtl_tx() while reading tp->cur_tx
+    - r8169: fix the KCSAN reported data-race in rtl_tx while reading
+      TxDescArray[entry].opts1
+    - r8169: fix the KCSAN reported data race in rtl_rx while reading desc->opts1
+    - i40e: Fix I40E_FLAG_VF_VLAN_PRUNING value
+    - treewide: Spelling fix in comment
+    - igb: Fix potential memory leak in igb_add_ethtool_nfc_entry
+    - neighbour: fix various data-races
+    - igc: Fix ambiguity in the ethtool advertising
+    - net: ieee802154: adf7242: Fix some potential buffer overflow in
+      adf7242_stats_show()
+    - net: usb: smsc95xx: Fix uninit-value access in smsc95xx_read_reg
+    - r8152: Increase USB control msg timeout to 5000ms as per spec
+    - r8152: Run the unload routine if we have errors during probe
+    - r8152: Cancel hw_phy_work if we have an error in probe
+    - r8152: Release firmware if we have an error in probe
+    - tcp: fix wrong RTO timeout when received SACK reneging
+    - gtp: uapi: fix GTPA_MAX
+    - gtp: fix fragmentation needed check with gso
+    - i40e: Fix wrong check for I40E_TXR_FLAGS_WB_ON_ITR
+    - kasan: print the original fault addr when access invalid shadow
+    - iio: exynos-adc: request second interupt only when touchscreen mode is used
+    - iio: adc: xilinx-xadc: Don't clobber preset voltage/temperature thresholds
+    - iio: adc: xilinx-xadc: Correct temperature offset/scale for UltraScale
+    - i2c: muxes: i2c-mux-pinctrl: Use of_get_i2c_adapter_by_node()
+    - i2c: muxes: i2c-mux-gpmux: Use of_get_i2c_adapter_by_node()
+    - i2c: muxes: i2c-demux-pinctrl: Use of_get_i2c_adapter_by_node()
+    - i2c: stm32f7: Fix PEC handling in case of SMBUS transfers
+    - i2c: aspeed: Fix i2c bus hang in slave read
+    - tracing/kprobes: Fix the description of variable length arguments
+    - misc: fastrpc: Clean buffers on remote invocation failures
+    - nvmem: imx: correct nregs for i.MX6ULL
+    - nvmem: imx: correct nregs for i.MX6SLL
+    - nvmem: imx: correct nregs for i.MX6UL
+    - perf/core: Fix potential NULL deref
+    - sparc32: fix a braino in fault handling in csum_and_copy_..._user()
+    - clk: Sanitize possible_parent_show to Handle Return Value of
+      of_clk_get_parent_name
+    - iio: afe: rescale: reorder includes
+    - iio: afe: rescale: expose scale processing function
+    - iio: afe: rescale: add offset support
+    - iio: afe: rescale: Accept only offset channels
+    - gve: Fix GFP flags when allocing pages
+    - x86/i8259: Skip probing when ACPI/MADT advertises PCAT compatibility
+    - x86/mm: Simplify RESERVE_BRK()
+    - x86/mm: Fix RESERVE_BRK() for older binutils
+    - ext4: add two helper functions extent_logical_end() and pa_logical_end()
+    - ext4: fix BUG in ext4_mb_new_inode_pa() due to overflow
+    - ext4: avoid overlapping preallocations due to overflow
+    - objtool/x86: add missing embedded_insn check
+    - driver: platform: Add helper for safer setting of driver_override
+    - rpmsg: Constify local variable in field store macro
+    - rpmsg: Fix kfree() of static memory on setting driver_override
+    - rpmsg: Fix calling device_lock() on non-initialized device
+    - rpmsg: glink: Release driver_override
+    - rpmsg: Fix possible refcount leak in rpmsg_register_device_override()
+    - x86: Fix .brk attribute in linker script
+    - ASoC: simple-card: fixup asoc_simple_probe() error handling
+    - net: sched: cls_u32: Fix allocation size in u32_init()
+    - irqchip/riscv-intc: Mark all INTC nodes as initialized
+    - irqchip/stm32-exti: add missing DT IRQ flag translation
+    - dmaengine: ste_dma40: Fix PM disable depth imbalance in d40_probe
+    - powerpc/85xx: Fix math emulation exception
+    - Input: synaptics-rmi4 - handle reset delay when using SMBus trsnsport
+    - fbdev: atyfb: only use ioremap_uc() on i386 and ia64
+    - fs/ntfs3: Add ckeck in ni_update_parent()
+    - fs/ntfs3: Write immediately updated ntfs state
+    - fs/ntfs3: Use kvmalloc instead of kmalloc(... __GFP_NOWARN)
+    - fs/ntfs3: Fix possible NULL-ptr-deref in ni_readpage_cmpr()
+    - fs/ntfs3: Fix NULL pointer dereference on error in attr_allocate_frame()
+    - fs/ntfs3: Fix directory element type detection
+    - fs/ntfs3: Avoid possible memory leak
+    - spi: npcm-fiu: Fix UMA reads when dummy.nbytes == 0
+    - netfilter: nfnetlink_log: silence bogus compiler warning
+    - ASoC: rt5650: fix the wrong result of key button
+    - drm/ttm: Reorder sys manager cleanup step
+    - fbdev: uvesafb: Call cn_del_callback() at the end of uvesafb_exit()
+    - scsi: mpt3sas: Fix in error path
+    - platform/mellanox: mlxbf-tmfifo: Fix a warning message
+    - net: chelsio: cxgb4: add an error code check in t4_load_phy_fw
+    - r8152: Check for unplug in rtl_phy_patch_request()
+    - r8152: Check for unplug in r8153b_ups_en() / r8153c_ups_en()
+    - powerpc/mm: Fix boot crash with FLATMEM
+    - can: isotp: set max PDU size to 64 kByte
+    - can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
+    - can: isotp: check CAN address family in isotp_bind()
+    - can: isotp: handle wait_event_interruptible() return values
+    - can: isotp: add local echo tx processing and tx without FC
+    - can: isotp: isotp_bind(): do not validate unused address information
+    - can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior
+    - drm/amd: Move helper for dynamic speed switch check out of smu13
+    - drm/amd: Disable ASPM for VI w/ all Intel systems
+    - PCI: Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device
+    - usb: storage: set 1.50 as the lower bcdDevice for older "Super Top"
+      compatibility
+    - usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
+    - usb: raw-gadget: properly handle interrupted requests
+    - tty: n_gsm: fix race condition in status line change on dead connections
+    - tty: 8250: Remove UC-257 and UC-431
+    - tty: 8250: Add support for additional Brainboxes UC cards
+    - tty: 8250: Add support for Brainboxes UP cards
+    - tty: 8250: Add support for Intashield IS-100
+    - tty: 8250: Fix port count of PX-257
+    - tty: 8250: Fix up PX-803/PX-857
+    - tty: 8250: Add support for additional Brainboxes PX cards
+    - tty: 8250: Add support for Intashield IX cards
+    - tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
+    - misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
+    - ALSA: hda: intel-dsp-config: Fix JSL Chromebook quirk detection
+    - Linux 5.15.138
+  * Jammy update: v5.15.137 upstream stable release (LP: #2049350)
+    - lib/Kconfig.debug: do not enable DEBUG_PREEMPT by default
+    - Documentation: sysctl: align cells in second content column
+    - xfs: don't expose internal symlink metadata buffers to the vfs
+    - Bluetooth: hci_event: Ignore NULL link key
+    - Bluetooth: Reject connection with the device which has same BD_ADDR
+    - Bluetooth: Fix a refcnt underflow problem for hci_conn
+    - Bluetooth: vhci: Fix race when opening vhci device
+    - Bluetooth: hci_event: Fix coding style
+    - Bluetooth: avoid memcmp() out of bounds warning
+    - ice: fix over-shifted variable
+    - ice: reset first in crash dump kernels
+    - nfc: nci: fix possible NULL pointer dereference in send_acknowledge()
+    - regmap: fix NULL deref on lookup
+    - KVM: x86: Mask LVTPC when handling a PMI
+    - tcp: check mptcp-level constraints for backlog coalescing
+    - fs/ntfs3: Fix possible null-pointer dereference in hdr_find_e()
+    - fs/ntfs3: fix panic about slab-out-of-bounds caused by ntfs_list_ea()
+    - fs/ntfs3: fix deadlock in mark_as_free_ex
+    - netfilter: nft_payload: fix wrong mac header matching
+    - drm/i915: Retry gtt fault when out of fence registers
+    - ASoC: codecs: wcd938x-sdw: fix use after free on driver unbind
+    - ASoC: codecs: wcd938x-sdw: fix runtime PM imbalance on probe errors
+    - ASoC: codecs: wcd938x: drop bogus bind error handling
+    - ASoC: codecs: wcd938x: fix unbind tear down order
+    - qed: fix LL2 RX buffer allocation
+    - xfrm: fix a data-race in xfrm_gen_index()
+    - xfrm: interface: use DEV_STATS_INC()
+    - net: ipv4: fix return value check in esp_remove_trailer
+    - net: ipv6: fix return value check in esp_remove_trailer
+    - net: rfkill: gpio: prevent value glitch during probe
+    - tcp: fix excessive TLP and RACK timeouts from HZ rounding
+    - tcp: tsq: relax tcp_small_queue_check() when rtx queue contains a single skb
+    - tun: prevent negative ifindex
+    - ipv4: fib: annotate races around nh->nh_saddr_genid and nh->nh_saddr
+    - net: usb: smsc95xx: Fix an error code in smsc95xx_reset()
+    - i40e: prevent crash on probe if hw registers have invalid values
+    - net: dsa: bcm_sf2: Fix possible memory leak in bcm_sf2_mdio_register()
+    - bonding: Return pointer to data after pull on skb
+    - net/sched: sch_hfsc: upgrade 'rt' to 'sc' when it becomes a inner curve
+    - neighbor: tracing: Move pin6 inside CONFIG_IPV6=y section
+    - netfilter: nft_set_rbtree: .deactivate fails if element has expired
+    - netfilter: nf_tables: do not remove elements if set backend implements
+      .abort
+    - netfilter: nf_tables: revert do not remove elements if set backend
+      implements .abort
+    - net: pktgen: Fix interface flags printing
+    - selftests/mm: fix awk usage in charge_reserved_hugetlb.sh and
+      hugetlb_reparenting_test.sh that may cause error
+    - serial: 8250: omap: Fix imprecise external abort for omap_8250_pm()
+    - serial: 8250_omap: Fix errors with no_console_suspend
+    - iio: Un-inline iio_buffer_enabled()
+    - iio: core: Hide read accesses to iio_dev->currentmode
+    - iio: core: introduce iio_device_{claim|release}_buffer_mode() APIs
+    - iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
+    - iio: adc: ad7192: Correct reference voltage
+    - perf: Add irq and exception return branch types
+    - perf/x86: Move branch classifier
+    - perf/x86/lbr: Filter vsyscall addresses
+    - drm/atomic-helper: relax unregistered connector check
+    - powerpc/32s: Remove capability to disable KUEP at boottime
+    - powerpc/32s: Do kuep_lock() and kuep_unlock() in assembly
+    - powerpc/47x: Fix 47x syscall return crash
+    - mctp: Allow local delivery to the null EID
+    - mctp: perform route lookups under a RCU read-side lock
+    - nfp: flower: avoid rmmod nfp crash issues
+    - ksmbd: not allow to open file if delelete on close bit is set
+    - ARM: dts: ti: omap: Fix noisy serial with overrun-throttle-ms for mapphone
+    - fs-writeback: do not requeue a clean inode having skipped pages
+    - btrfs: return -EUCLEAN for delayed tree ref with a ref count not equals to 1
+    - btrfs: initialize start_slot in btrfs_log_prealloc_extents
+    - i2c: mux: Avoid potential false error message in i2c_mux_add_adapter
+    - overlayfs: set ctime when setting mtime and atime
+    - gpio: timberdale: Fix potential deadlock on &tgpio->lock
+    - ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
+    - ata: libata-eh: Fix compilation warning in ata_eh_link_report()
+    - tracing: relax trace_event_eval_update() execution with cond_resched()
+    - wifi: mwifiex: Sanity check tlv_len and tlv_bitmap_len
+    - wifi: iwlwifi: Ensure ack flag is properly cleared.
+    - HID: holtek: fix slab-out-of-bounds Write in holtek_kbd_input_event
+    - Bluetooth: btusb: add shutdown function for QCA6174
+    - Bluetooth: Avoid redundant authentication
+    - Bluetooth: hci_core: Fix build warnings
+    - wifi: cfg80211: Fix 6GHz scan configuration
+    - wifi: mac80211: allow transmitting EAPOL frames with tainted key
+    - wifi: cfg80211: avoid leaking stack data into trace
+    - regulator/core: Revert "fix kobject release warning and memory leak in
+      regulator_register()"
+    - sky2: Make sure there is at least one frag_addr available
+    - ipv4/fib: send notify when delete source address routes
+    - drm: panel-orientation-quirks: Add quirk for One Mix 2S
+    - btrfs: fix some -Wmaybe-uninitialized warnings in ioctl.c
+    - btrfs: error out when COWing block using a stale transaction
+    - btrfs: error when COWing block from a root that is being deleted
+    - btrfs: error out when reallocating block for defrag using a stale
+      transaction
+    - HID: multitouch: Add required quirk for Synaptics 0xcd7e device
+    - platform/x86: touchscreen_dmi: Add info for the Positivo C4128B
+    - net/mlx5: Handle fw tracer change ownership event based on MTRC
+    - Bluetooth: hci_event: Fix using memcmp when comparing keys
+    - net: introduce a function to check if a netdev name is in use
+    - net: move from strlcpy with unused retval to strscpy
+    - net: fix ifname in netlink ntf during netns move
+    - mtd: rawnand: qcom: Unmap the right resource upon probe failure
+    - mtd: rawnand: pl353: Ensure program page operations are successful
+    - mtd: rawnand: marvell: Ensure program page operations are successful
+    - mtd: rawnand: arasan: Ensure program page operations are successful
+    - mtd: spinand: micron: correct bitmask for ecc status
+    - mtd: physmap-core: Restore map_rom fallback
+    - mmc: mtk-sd: Use readl_poll_timeout_atomic in msdc_reset_hw
+    - mmc: core: sdio: hold retuning if sdio in 1-bit mode
+    - pNFS: Fix a hang in nfs4_evict_inode()
+    - NFSv4.1: fixup use EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - ACPI: irq: Fix incorrect return value in acpi_register_gsi()
+    - nvme-pci: add BOGUS_NID for Intel 0a54 device
+    - nvme-rdma: do not try to stop unallocated queues
+    - USB: serial: option: add Telit LE910C4-WWX 0x1035 composition
+    - USB: serial: option: add entry for Sierra EM9191 with new firmware
+    - USB: serial: option: add Fibocom to DELL custom modem FM101R-GL
+    - s390/pci: fix iommu bitmap allocation
+    - selftests/ftrace: Add new test case which checks non unique symbol
+    - s390/cio: fix a memleak in css_alloc_subchannel
+    - platform/surface: platform_profile: Propagate error if profile registration
+      fails
+    - platform/x86: asus-wmi: Change ASUS_WMI_BRN_DOWN code from 0x20 to 0x2e
+    - platform/x86: asus-wmi: Map 0x2a code, Ignore 0x2b and 0x2c events
+    - gpio: vf610: set value before the direction to avoid a glitch
+    - ASoC: pxa: fix a memory leak in probe()
+    - serial: 8250: omap: Move uart_write() inside PM section
+    - phy: mapphone-mdm6600: Fix runtime disable on probe
+    - phy: mapphone-mdm6600: Fix runtime PM for remove
+    - phy: mapphone-mdm6600: Fix pinctrl_pm handling for sleep pins
+    - Bluetooth: hci_sock: fix slab oob read in create_monitor_event
+    - Bluetooth: hci_sock: Correctly bounds check and pad HCI_MON_NEW_INDEX name
+    - xfrm6: fix inet6_dev refcount underflow problem
+    - Linux 5.15.137
+  * CVE-2023-51782
+    - net/rose: Fix Use-After-Free in rose_ioctl
+  * CVE-2023-51779
+    - Bluetooth: af_bluetooth: Fix Use-After-Free in bt_sock_recvmsg
+  * CVE-2023-22995
+    - usb: dwc3: dwc3-qcom: Add missing platform_device_put() in
+      dwc3_qcom_acpi_register_core
+  * CVE-2023-4134
+    - Input: cyttsp4_core - change del_timer_sync() to timer_shutdown_sync()
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 24 Apr 2024 12:58:05 +1000
+
+linux-xilinx-zynqmp (5.15.0-1027.31) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1027.31 -proposed tracker (LP: #2054500)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/d2024.02.07)
+
+  * Fix backported kria device tree changes (LP: #2054366)
+    - SAUCE: zynqmp.dtsi fix incorrectly backported changes
+
+  [ Ubuntu: 5.15.0-94.104 ]
+
+  * jammy/linux: 5.15.0-94.104 -proposed tracker (LP: #2048777)
+  * [SRU] Duplicate Device_dax ids Created and hence Probing is Failing.
+    (LP: #2028158)
+    - device-dax: Fix duplicate 'hmem' device registration
+  * Add ODM driver f81604 usb-can (LP: #2045387)
+    - can: usb: f81604: add Fintek F81604 support
+    - [Config] updateconfigs for ODM drivers CONFIG_CAN_F81604
+  * Add ODM driver gpio-m058ssan (LP: #2045386)
+    - SAUCE: ODM: gpio: add M058SSAN gpio driver
+    - [Config] updateconfigs for ODM drivers CONFIG_GPIO_M058SSAN
+  * Add ODM driver rtc-pcf85263 (LP: #2045385)
+    - SAUCE: ODM: rtc: add PCF85263 RTC driver
+    - [Config] updateconfigs for ODM drivers CONFIG_RTC_DRV_PCF85263
+  * AppArmor patch for mq-posix interface is missing in jammy (LP: #2045384)
+    - SAUCE: (no-up) apparmor: reserve mediation classes
+    - SAUCE: (no-up) apparmor: Add fine grained mediation of posix mqueues
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+  [ Ubuntu: 5.15.0-93.103 ]
+
+  * jammy/linux: 5.15.0-93.103 -proposed tracker (LP: #2048330)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] remove helper scripts
+    - [Packaging] update annotations scripts
+    - debian/dkms-versions -- update from kernel-versions (main/2024.01.08)
+  * Hotplugging SCSI disk in QEMU VM fails (LP: #2047382)
+    - Revert "PCI: acpiphp: Reassign resources on bridge if necessary"
+  * CVE-2023-6622
+    - netfilter: nf_tables: bail out on mismatching dynset and set expressions
+  * CVE-2024-0193
+    - netfilter: nf_tables: skip set commit for deleted/destroyed sets
+  * CVE-2023-6040
+    - netfilter: nf_tables: Reject tables of unsupported family
+  * Patches needed for AmpereOne (arm64) (LP: #2044192)
+    - clocksource/arm_arch_timer: Add build-time guards for unhandled register
+      accesses
+    - clocksource/drivers/arm_arch_timer: Drop CNT*_TVAL read accessors
+    - clocksource/drivers/arm_arch_timer: Extend write side of timer register
+      accessors to u64
+    - clocksource/drivers/arm_arch_timer: Move system register timer programming
+      over to CVAL
+    - clocksource/drivers/arm_arch_timer: Move drop _tval from erratum function
+      names
+    - clocksource/drivers/arm_arch_timer: Fix MMIO base address vs callback
+      ordering issue
+    - clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL
+    - clocksource/drivers/arm_arch_timer: Advertise 56bit timer to the core code
+    - clocksource/drivers/arm_arch_timer: Work around broken CVAL implementations
+    - clocksource/drivers/arm_arch_timer: Remove any trace of the TVAL programming
+      interface
+    - clocksource/drivers/arm_arch_timer: Drop unnecessary ISB on CVAL programming
+    - clocksource/drivers/arm_arch_timer: Fix masking for high freq counters
+    - clocksource/drivers/arch_arm_timer: Move workaround synchronisation around
+  * Add quirk to disable i915 fastboot on B&R PC (LP: #2047630)
+    - SAUCE: i915: force disable fastboot quirk
+  * Some machines can't pass the pm-graph test (LP: #2046217)
+    - wifi: iwlwifi: pcie: rescan bus if no parent
+  * Sound: Add rtl quirk of M90-Gen5 (LP: #2046105)
+    - ALSA: hda/realtek: Enable headset on Lenovo M90 Gen5
+  * linux tools packages for derived kernels refuse to install simultaneously
+    due to libcpupower name collision (LP: #2035971)
+    - [Packaging] Statically link libcpupower into cpupower tool
+  * [Debian] autoreconstruct - Do not generate chmod -x for deleted  files
+    (LP: #2045562)
+    - [Debian] autoreconstruct - Do not generate chmod -x for deleted files
+  * CVE-2023-6931
+    - perf/core: Add a new read format to get a number of lost samples
+    - perf: Fix perf_event_validate_size()
+    - perf: Fix perf_event_validate_size() lockdep splat
+  * CVE-2023-6932
+    - ipv4: igmp: fix refcnt uaf issue when receiving igmp query packet
+  * CVE-2023-6606
+    - smb: client: fix OOB in smbCalcSize()
+  * CVE-2023-6817
+    - netfilter: nft_set_pipapo: skip inactive elements during set walk
+  * Jammy update: v5.15.136 upstream stable release (LP: #2046008)
+    - iommu/vt-d: Avoid memory allocation in iommu_suspend()
+    - scsi: core: Use a structure member to track the SCSI command submitter
+    - scsi: core: Rename scsi_mq_done() into scsi_done() and export it
+    - scsi: ib_srp: Call scsi_done() directly
+    - RDMA/srp: Do not call scsi_done() from srp_abort()
+    - RDMA/cxgb4: Check skb value for failure to allocate
+    - perf/arm-cmn: Fix the unhandled overflow status of counter 4 to 7
+    - of: overlay: Reorder struct fragment fields kerneldoc
+    - platform/x86: think-lmi: Fix reference leak
+    - platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section
+      mismatch warning
+    - lib/test_meminit: fix off-by-one error in test_pages()
+    - HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect
+    - quota: Fix slow quotaoff
+    - net: prevent address rewrite in kernel_bind()
+    - ALSA: usb-audio: Fix microphone sound on Opencomm2 Headset
+    - KEYS: trusted: allow use of kernel RNG for key material
+    - KEYS: trusted: Remove redundant static calls usage
+    - drm/msm/dp: do not reinitialize phy unless retry during link training
+    - drm/msm/dsi: skip the wait for video mode done if not applicable
+    - drm/msm/dsi: fix irq_of_parse_and_map() error checking
+    - drm/msm/dpu: change _dpu_plane_calc_bw() to use u64 to avoid overflow
+    - ravb: Fix up dma_free_coherent() call in ravb_remove()
+    - ravb: Fix use-after-free issue in ravb_tx_timeout_work()
+    - ieee802154: ca8210: Fix a potential UAF in ca8210_probe
+    - mlxsw: fix mlxsw_sp2_nve_vxlan_learning_set() return type
+    - eth: remove copies of the NAPI_POLL_WEIGHT define
+    - xen-netback: use default TX queue size for vifs
+    - riscv, bpf: Factor out emit_call for kernel and bpf context
+    - riscv, bpf: Sign-extend return values
+    - drm/vmwgfx: fix typo of sizeof argument
+    - bpf: Fix verifier log for async callback return values
+    - net: macsec: indicate next pn update when offloading
+    - net: phy: mscc: macsec: reject PN update requests
+    - ixgbe: fix crash with empty VF macvlan list
+    - net/mlx5e: Again mutually exclude RX-FCS and RX-port-timestamp
+    - net: nfc: fix races in nfc_llcp_sock_get() and nfc_llcp_sock_get_sn()
+    - pinctrl: renesas: rzn1: Enable missing PINMUX
+    - nfc: nci: assert requested protocol is valid
+    - workqueue: Override implicit ordered attribute in
+      workqueue_apply_unbound_cpumask()
+    - net: add sysctl accept_ra_min_rtr_lft
+    - net: change accept_ra_min_rtr_lft to affect all RA lifetimes
+    - net: release reference to inet6_dev pointer
+    - media: mtk-jpeg: Fix use after free bug due to uncanceled work
+    - dmaengine: stm32-mdma: abort resume if no ongoing transfer
+    - xhci: Keep interrupt disabled in initialization until host is running.
+    - usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
+    - net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read
+    - usb: dwc3: Soft reset phy on probe for host
+    - usb: cdns3: Modify the return value of cdns_set_active () to void when
+      CONFIG_PM_SLEEP is disabled
+    - usb: musb: Get the musb_qh poniter after musb_giveback
+    - usb: musb: Modify the "HWVers" register address
+    - iio: pressure: bmp280: Fix NULL pointer exception
+    - iio: pressure: dps310: Adjust Timeout Settings
+    - iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
+    - drm/amdgpu: add missing NULL check
+    - drm/amd/display: Don't set dpms_off for seamless boot
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA
+    - x86/cpu: Fix AMD erratum #1485 on Zen4-based CPUs
+    - mcb: remove is_added flag from mcb_device struct
+    - thunderbolt: Workaround an IOMMU fault on certain systems with Intel Maple
+      Ridge
+    - thunderbolt: Check that lane 1 is in CL0 before enabling lane bonding
+    - libceph: use kernel_connect()
+    - ceph: fix incorrect revoked caps assert in ceph_fill_file_size()
+    - ceph: fix type promotion bug on 32bit systems
+    - Input: powermate - fix use-after-free in powermate_config_complete
+    - Input: psmouse - fix fast_reconnect function for PS/2 mode
+    - Input: xpad - add PXN V900 support
+    - Input: i8042 - add Fujitsu Lifebook E5411 to i8042 quirk table
+    - Input: goodix - ensure int GPIO is in input for gpio_count == 1 &&
+      gpio_int_idx == 0 case
+    - tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
+    - cgroup: Remove duplicates in cgroup v1 tasks file
+    - counter: microchip-tcb-capture: Fix the use of internal GCLK logic
+    - usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
+    - usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
+    - usb: cdnsp: Fixes issue with dequeuing not queued requests
+    - x86/alternatives: Disable KASAN in apply_alternatives()
+    - dmaengine: idxd: use spin_lock_irqsave before wait_event_lock_irq
+    - dmaengine: mediatek: Fix deadlock caused by synchronize_irq()
+    - powerpc/8xx: Fix pte_access_permitted() for PAGE_NONE
+    - powerpc/64e: Fix wrong test in __ptep_test_and_clear_young()
+    - arm64: report EL1 UNDEFs better
+    - arm64: die(): pass 'err' as long
+    - arm64: consistently pass ESR_ELx to die()
+    - arm64: rework FPAC exception handling
+    - arm64: rework BTI exception handling
+    - arm64: allow kprobes on EL0 handlers
+    - arm64: split EL0/EL1 UNDEF handlers
+    - arm64: factor out EL1 SSBS emulation hook
+    - arm64: factor insn read out of call_undef_hook()
+    - arm64: rework EL0 MRS emulation
+    - arm64: armv8_deprecated: fold ops into insn_emulation
+    - arm64: armv8_deprecated move emulation functions
+    - arm64: armv8_deprecated: move aarch32 helper earlier
+    - arm64: armv8_deprecated: rework deprected instruction handling
+    - arm64: armv8_deprecated: fix unused-function error
+    - usb: hub: Guard against accesses to uninitialized BOS descriptors
+    - eth: remove remaining copies of the NAPI_POLL_WEIGHT define
+    - Linux 5.15.136
+  * Jammy update: v5.15.135 upstream stable release (LP: #2045809)
+    - spi: zynqmp-gqspi: Convert to platform remove callback returning void
+    - spi: zynqmp-gqspi: fix clock imbalance on probe failure
+    - ASoC: soc-utils: Export snd_soc_dai_is_dummy() symbol
+    - ASoC: tegra: Fix redundant PLLA and PLLA_OUT0 updates
+    - NFS: Cleanup unused rpc_clnt variable
+    - NFS: rename nfs_client_kset to nfs_kset
+    - NFSv4: Fix a state manager thread deadlock regression
+    - ring-buffer: remove obsolete comment for free_buffer_page()
+    - ring-buffer: Fix bytes info in per_cpu buffer stats
+    - arm64: Avoid repeated AA64MMFR1_EL1 register read on pagefault path
+    - iommu/arm-smmu-v3: Set TTL invalidation hint better
+    - iommu/arm-smmu-v3: Avoid constructing invalid range commands
+    - rbd: move rbd_dev_refresh() definition
+    - rbd: decouple header read-in from updating rbd_dev->header
+    - rbd: decouple parent info read-in from updating rbd_dev
+    - rbd: take header_rwsem in rbd_dev_refresh() only when updating
+    - block: fix use-after-free of q->q_usage_counter
+    - scsi: zfcp: Fix a double put in zfcp_port_enqueue()
+    - qed/red_ll2: Fix undefined behavior bug in struct qed_ll2_info
+    - wifi: mwifiex: Fix tlv_buf_left calculation
+    - net: replace calls to sock->ops->connect() with kernel_connect()
+    - net: prevent rewrite of msg_name in sock_sendmsg()
+    - drm/amd: Fix detection of _PR3 on the PCIe root port
+    - arm64: Add Cortex-A520 CPU part definition
+    - HID: sony: Fix a potential memory leak in sony_probe()
+    - ubi: Refuse attaching if mtd's erasesize is 0
+    - wifi: iwlwifi: dbg_ini: fix structure packing
+    - iwlwifi: avoid void pointer arithmetic
+    - wifi: iwlwifi: mvm: Fix a memory corruption issue
+    - wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
+    - bpf: Fix tr dereferencing
+    - drivers/net: process the result of hdlc_open() and add call of hdlc_close()
+      in uhdlc_close()
+    - wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
+    - regmap: rbtree: Fix wrong register marked as in-cache when creating new node
+    - ima: Finish deprecation of IMA_TRUSTED_KEYRING Kconfig
+    - [Config] updateconfigs for IMA_BLACKLIST_KEYRING
+    - scsi: target: core: Fix deadlock due to recursive locking
+    - ima: rework CONFIG_IMA dependency block
+    - NFSv4: Fix a nfs4_state_manager() race
+    - bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
+    - modpost: add missing else to the "of" check
+    - net: fix possible store tearing in neigh_periodic_work()
+    - ipv4, ipv6: Fix handling of transhdrlen in __ip{,6}_append_data()
+    - ptp: ocp: Fix error handling in ptp_ocp_device_init
+    - net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent
+    - net: usb: smsc75xx: Fix uninit-value access in __smsc75xx_read_reg
+    - net: nfc: llcp: Add lock when modifying device list
+    - net: ethernet: ti: am65-cpsw: Fix error code in
+      am65_cpsw_nuss_init_tx_chns()
+    - ibmveth: Remove condition to recompute TCP header checksum.
+    - netfilter: handle the connecting collision properly in
+      nf_conntrack_proto_sctp
+    - netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
+    - ipv4: Set offload_failed flag in fibmatch results
+    - net: stmmac: dwmac-stm32: fix resume on STM32 MCU
+    - tipc: fix a potential deadlock on &tx->lock
+    - tcp: fix quick-ack counting to count actual ACKs of new data
+    - tcp: fix delayed ACKs for MSS boundary condition
+    - sctp: update transport state when processing a dupcook packet
+    - sctp: update hb timer immediately after users change hb_interval
+    - HID: sony: remove duplicate NULL check before calling usb_free_urb()
+    - HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit
+    - dm zoned: free dmz->ddev array in dmz_put_zoned_devices
+    - RDMA/core: Require admin capabilities to set system parameters
+    - of: dynamic: Fix potential memory leak in of_changeset_action()
+    - IB/mlx4: Fix the size of a buffer in add_port_entries()
+    - gpio: aspeed: fix the GPIO number passed to pinctrl_gpio_set_config()
+    - gpio: pxa: disable pinctrl calls for MMP_GPIO
+    - RDMA/cma: Initialize ib_sa_multicast structure to 0 when join
+    - RDMA/cma: Fix truncation compilation warning in make_cma_ports
+    - RDMA/uverbs: Fix typo of sizeof argument
+    - RDMA/siw: Fix connection failure handling
+    - RDMA/mlx5: Fix NULL string error
+    - ksmbd: fix uaf in smb20_oplock_break_ack
+    - parisc: Restore __ldcw_align for PA-RISC 2.0 processors
+    - xen/events: replace evtchn_rwlock with RCU
+    - Linux 5.15.135
+  * CVE-2023-46813
+    - x86/sev: Disable MMIO emulation from user mode
+    - x86/sev: Check IOBM for IOIO exceptions from user-space
+    - x86/sev: Check for user-space IOIO pointing to kernel space
+  * CVE-2023-6111
+    - netfilter: nf_tables: remove catchall element in GC sync path
+  * Change in trace file leads to test timeout in ftrace tests on 5.15 ARM64
+    (LP: #2029405)
+    - selftests/ftrace: Stop tracing while reading the trace file by default
+  * Fix ADL: System enabled AHCI can't get into s0ix when attached ODD
+    (LP: #2037493)
+    - ata: ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list
+  * Kernel doesn't compile with CONFIG_IMA (LP: #2041842)
+    - SAUCE: LSM: Fix typo in ima_filter_rule_match struct argument
+  * CVE-2023-32252
+    - ksmbd: add smb-direct shutdown
+    - ksmbd: Implements sess->ksmbd_chann_list as xarray
+    - ksmbd: fix racy issue from session setup and logoff
+  * Jammy update: v5.15.134 upstream stable release (LP: #2044023)
+    - NFS: Use the correct commit info in nfs_join_page_group()
+    - NFS: More fixes for nfs_direct_write_reschedule_io()
+    - NFS/pNFS: Report EINVAL errors from connect() to the server
+    - SUNRPC: Mark the cred for revalidation if the server rejects it
+    - NFSv4.1: use EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - NFSv4.1: fix pnfs MDS=DS session trunking
+    - tracing: Make trace_marker{,_raw} stream-like
+    - tracing: Increase trace array ref count on enable and filter files
+    - ata: ahci: Drop pointless VPRINTK() calls and convert the remaining ones
+    - ata: libahci: clear pending interrupt status
+    - ext4: scope ret locally in ext4_try_to_trim_range()
+    - ext4: change s_last_trim_minblks type to unsigned long
+    - ext4: replace the traditional ternary conditional operator with with
+      max()/min()
+    - ext4: move setting of trimmed bit into ext4_try_to_trim_range()
+    - ext4: do not let fstrim block system suspend
+    - tracing: Have event inject files inc the trace array ref count
+    - netfilter: nft_set_rbtree: use read spinlock to avoid datapath contention
+    - netfilter: nft_set_pipapo: call nft_trans_gc_queue_sync() in catchall GC
+    - netfilter: nft_set_pipapo: stop GC iteration if GC transaction allocation
+      fails
+    - netfilter: nft_set_hash: try later when GC hits EAGAIN on iteration
+    - netfilter: nf_tables: fix memleak when more than 255 elements expired
+    - ASoC: meson: spdifin: start hw on dai probe
+    - netfilter: nf_tables: disallow element removal on anonymous sets
+    - bpf: Avoid deadlock when using queue and stack maps from NMI
+    - selftests: tls: swap the TX and RX sockets in some tests
+    - net/core: Fix ETH_P_1588 flow dissector
+    - ASoC: imx-audmix: Fix return error with devm_clk_get()
+    - iavf: do not process adminq tasks when __IAVF_IN_REMOVE_TASK is set
+    - i40e: Add VF VLAN pruning
+    - i40e: Fix VF VLAN offloading when port VLAN is configured
+    - ionic: fix 16bit math issue when PAGE_SIZE >= 64KB
+    - igc: Fix infinite initialization loop with early XDP redirect
+    - powerpc/perf/hv-24x7: Update domain value check
+    - dccp: fix dccp_v4_err()/dccp_v6_err() again
+    - platform/x86: intel_scu_ipc: Check status after timeout in busy_loop()
+    - platform/x86: intel_scu_ipc: Check status upon timeout in
+      ipc_wait_for_interrupt()
+    - platform/x86: intel_scu_ipc: Don't override scu in
+      intel_scu_ipc_dev_simple_command()
+    - platform/x86: intel_scu_ipc: Fail IPC send if still busy
+    - x86/srso: Fix srso_show_state() side effect
+    - x86/srso: Fix SBPB enablement for spec_rstack_overflow=off
+    - net: hns3: fix GRE checksum offload issue
+    - net: hns3: only enable unicast promisc when mac table full
+    - net: hns3: fix fail to delete tc flower rules during reset issue
+    - net: hns3: add 5ms delay before clear firmware reset irq source
+    - net: bridge: use DEV_STATS_INC()
+    - team: fix null-ptr-deref when team device type is changed
+    - net: rds: Fix possible NULL-pointer dereference
+    - netfilter: nf_tables: disable toggling dormant table state more than once
+    - locking/seqlock: Do the lockdep annotation before locking in
+      do_write_seqcount_begin_nested()
+    - net: ena: Flush XDP packets on error.
+    - bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
+    - igc: Expose tx-usecs coalesce setting to user
+    - Fix up backport of 136191703038 ("interconnect: Teach lockdep about
+      icc_bw_lock order")
+    - gpio: tb10x: Fix an error handling path in tb10x_gpio_probe()
+    - i2c: mux: demux-pinctrl: check the return value of devm_kstrdup()
+    - i2c: mux: gpio: Replace custom acpi_get_local_address()
+    - i2c: mux: gpio: Add missing fwnode_handle_put()
+    - xfs: bound maximum wait time for inodegc work
+    - xfs: introduce xfs_inodegc_push()
+    - xfs: explicitly specify cpu when forcing inodegc delayed work to run
+      immediately
+    - xfs: check that per-cpu inodegc workers actually run on that cpu
+    - xfs: disable reaping in fscounters scrub
+    - xfs: fix xfs_inodegc_stop racing with mod_delayed_work
+    - Input: i8042 - rename i8042-x86ia64io.h to i8042-acpipnpio.h
+    - Input: i8042 - add quirk for TUXEDO Gemini 17 Gen1/Clevo PD70PN
+    - netfilter: exthdr: add support for tcp option removal
+    - netfilter: nft_exthdr: Fix non-linear header modification
+    - ata: libata: Rename link flag ATA_LFLAG_NO_DB_DELAY
+    - ata: ahci: Add support for AMD A85 FCH (Hudson D4)
+    - ata: ahci: Rename board_ahci_mobile
+    - ata: ahci: Add Elkhart Lake AHCI controller
+    - scsi: qla2xxx: Select qpair depending on which CPU post_cmd() gets called
+    - scsi: qla2xxx: Use raw_smp_processor_id() instead of smp_processor_id()
+    - btrfs: reset destination buffer when read_extent_buffer() gets invalid range
+    - MIPS: Alchemy: only build mmc support helpers if au1xmmc is enabled
+    - drm/bridge: ti-sn65dsi83: Do not generate HFP/HBP/HSA and EOT packet
+    - bus: ti-sysc: Use fsleep() instead of usleep_range() in sysc_reset()
+    - bus: ti-sysc: Fix missing AM35xx SoC matching
+    - clk: tegra: fix error return case for recalc_rate
+    - treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_56.RULE
+      (part 1)
+    - ARM: dts: omap: correct indentation
+    - ARM: dts: ti: omap: Fix bandgap thermal cells addressing for omap3/4
+    - ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot
+    - bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up
+    - power: supply: ucs1002: fix error code in ucs1002_get_property()
+    - firmware: imx-dsp: Fix an error handling path in imx_dsp_setup_channels()
+    - xtensa: add default definition for XCHAL_HAVE_DIV32
+    - xtensa: iss/network: make functions static
+    - xtensa: boot: don't add include-dirs
+    - xtensa: boot/lib: fix function prototypes
+    - soc: imx8m: Enable OCOTP clock for imx8mm before reading registers
+    - gpio: pmic-eic-sprd: Add can_sleep flag for PMIC EIC chip
+    - i2c: npcm7xx: Fix callback completion ordering
+    - dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock
+    - spi: sun6i: reduce DMA RX transfer width to single byte
+    - spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
+    - parisc: sba: Fix compile warning wrt list of SBA devices
+    - parisc: iosapic.c: Fix sparse warnings
+    - parisc: drivers: Fix sparse warning
+    - parisc: irq: Make irq_stack_union static to avoid sparse warning
+    - scsi: qedf: Add synchronization between I/O completions and abort
+    - scsi: ufs: core: Move __ufshcd_send_uic_cmd() outside host_lock
+    - selftests/ftrace: Correctly enable event in instance-event.tc
+    - ring-buffer: Avoid softlockup in ring_buffer_resize()
+    - btrfs: improve error message after failure to add delayed dir index item
+    - selftests: fix dependency checker script
+    - ring-buffer: Do not attempt to read past "commit"
+    - platform/mellanox: mlxbf-bootctl: add NET dependency into Kconfig
+    - drm/amd/display: Don't check registers, if using AUX BL control
+    - drm/amdgpu: Handle null atom context in VBIOS info ioctl
+    - scsi: pm80xx: Use phy-specific SAS address when sending PHY_START command
+    - scsi: pm80xx: Avoid leaking tags when processing
+      OPC_INB_SET_CONTROLLER_CONFIG command
+    - smb3: correct places where ENOTSUPP is used instead of preferred EOPNOTSUPP
+    - ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()
+    - spi: nxp-fspi: reset the FLSHxCR1 registers
+    - spi: stm32: add a delay before SPI disable
+    - ASoC: fsl: imx-pcm-rpmsg: Add SNDRV_PCM_INFO_BATCH flag
+    - bpf: Clarify error expectations from bpf_clone_redirect
+    - ASoC: imx-rpmsg: Set ignore_pmdown_time for dai_link
+    - media: vb2: frame_vector.c: replace WARN_ONCE with a comment
+    - powerpc/watchpoints: Disable preemption in thread_change_pc()
+    - powerpc/watchpoint: Disable pagefaults when getting user instruction
+    - powerpc/watchpoints: Annotate atomic context in more places
+    - ncsi: Propagate carrier gain/loss events to the NCSI controller
+    - fbdev/sh7760fb: Depend on FB=y
+    - perf build: Define YYNOMEM as YYNOABORT for bison < 3.81
+    - sched/cpuacct: Optimize away RCU read lock
+    - cgroup: Fix suspicious rcu_dereference_check() usage warning
+    - nvme-pci: factor the iod mempool creation into a helper
+    - nvme-pci: factor out a nvme_pci_alloc_dev helper
+    - nvme-pci: do not set the NUMA node of device if it has none
+    - watchdog: iTCO_wdt: No need to stop the timer in probe
+    - watchdog: iTCO_wdt: Set NO_REBOOT if the watchdog is not already running
+    - i40e: fix potential NULL pointer dereferencing of pf->vf
+      i40e_sync_vsi_filters()
+    - scsi: qla2xxx: Fix NULL pointer dereference in target mode
+    - nvme-pci: always return an ERR_PTR from nvme_pci_alloc_dev
+    - smack: Record transmuting in smk_transmuted
+    - smack: Retrieve transmuting information in smack_inode_getsecurity()
+    - Smack:- Use overlay inode label in smack_inode_copy_up()
+    - iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range
+    - x86/srso: Add SRSO mitigation for Hygon processors
+    - Revert "tty: n_gsm: fix UAF in gsm_cleanup_mux"
+    - serial: 8250_port: Check IRQ data before use
+    - nilfs2: fix potential use after free in nilfs_gccache_submit_read_data()
+    - ALSA: hda: Disable power save for solving pop issue on Lenovo ThinkCentre
+      M70q
+    - ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
+    - i2c: i801: unregister tco_pdev in i801_probe() error path
+    - sched/rt: Fix live lock between select_fallback_rq() and RT push
+    - io_uring/fs: remove sqe->rw_flags checking from LINKAT
+    - Revert "SUNRPC dont update timeout value on connection reset"
+    - proc: nommu: /proc/<pid>/maps: release mmap read lock
+    - ring-buffer: Update "shortest_full" in polling
+    - btrfs: properly report 0 avail for very full file systems
+    - bpf: Fix BTF_ID symbol generation collision
+    - bpf: Fix BTF_ID symbol generation collision in tools/
+    - net: thunderbolt: Fix TCPv6 GSO checksum calculation
+    - ata: libata-core: Fix ata_port_request_pm() locking
+    - ata: libata-core: Fix port and device removal
+    - ata: libata-core: Do not register PM operations for SAS ports
+    - ata: libata-sata: increase PMP SRST timeout to 10s
+    - fs: binfmt_elf_efpic: fix personality for ELF-FDPIC
+    - drm/meson: fix memory leak on ->hpd_notify callback
+    - Linux 5.15.134
+  * Jammy update: v5.15.133 upstream stable release (LP: #2043422)
+    - autofs: fix memory leak of waitqueues in autofs_catatonic_mode
+    - btrfs: output extra debug info if we failed to find an inline backref
+    - locks: fix KASAN: use-after-free in trace_event_raw_event_filelock_lock
+    - ACPICA: Add AML_NO_OPERAND_RESOLVE flag to Timer
+    - kernel/fork: beware of __put_task_struct() calling context
+    - rcuscale: Move rcu_scale_writer() schedule_timeout_uninterruptible() to
+      _idle()
+    - scftorture: Forgive memory-allocation failure if KASAN
+    - ACPI: video: Add backlight=native DMI quirk for Lenovo Ideapad Z470
+    - perf/smmuv3: Enable HiSilicon Erratum 162001900 quirk for HIP08/09
+    - perf/imx_ddr: speed up overflow frequency of cycle
+    - hw_breakpoint: fix single-stepping when using bpf_overflow_handler
+    - ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
+    - devlink: remove reload failed checks in params get/set callbacks
+    - crypto: lrw,xts - Replace strlcpy with strscpy
+    - wifi: ath9k: fix fortify warnings
+    - wifi: ath9k: fix printk specifier
+    - wifi: mwifiex: fix fortify warning
+    - wifi: wil6210: fix fortify warnings
+    - crypto: lib/mpi - avoid null pointer deref in mpi_cmp_ui()
+    - tpm_tis: Resend command to recover from data transfer errors
+    - mmc: sdhci-esdhc-imx: improve ESDHC_FLAG_ERR010450
+    - alx: fix OOB-read compiler warning
+    - wifi: mac80211: check S1G action frame size
+    - netfilter: ebtables: fix fortify warnings in size_entry_mwt()
+    - wifi: mac80211_hwsim: drop short frames
+    - drm/bridge: tc358762: Instruct DSI host to generate HSE packets
+    - arm64: dts: qcom: sm6125-pdx201: correct ramoops pmsg-size
+    - arm64: dts: qcom: sm8150-kumano: correct ramoops pmsg-size
+    - arm64: dts: qcom: sm8250-edo: correct ramoops pmsg-size
+    - samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'
+    - ALSA: hda: intel-dsp-cfg: add LunarLake support
+    - drm/amd/display: Blocking invalid 420 modes on HDMI TMDS for DCN31
+    - drm/exynos: fix a possible null-pointer dereference due to data race in
+      exynos_drm_crtc_atomic_disable()
+    - bus: ti-sysc: Configure uart quirks for k3 SoC
+    - md: raid1: fix potential OOB in raid1_remove_disk()
+    - ext2: fix datatype of block number in ext2_xattr_set2()
+    - fs/jfs: prevent double-free in dbUnmount() after failed jfs_remount()
+    - jfs: fix invalid free of JFS_IP(ipimap)->i_imap in diUnmount
+    - ARM: 9317/1: kexec: Make smp stop calls asynchronous
+    - powerpc/pseries: fix possible memory leak in ibmebus_bus_init()
+    - PCI: fu740: Set the number of MSI vectors
+    - media: dvb-usb-v2: af9035: Fix null-ptr-deref in af9035_i2c_master_xfer
+    - media: dw2102: Fix null-ptr-deref in dw2102_i2c_transfer()
+    - media: af9005: Fix null-ptr-deref in af9005_i2c_xfer
+    - media: anysee: fix null-ptr-deref in anysee_master_xfer
+    - media: az6007: Fix null-ptr-deref in az6007_i2c_xfer()
+    - media: dvb-usb-v2: gl861: Fix null-ptr-deref in gl861_i2c_master_xfer
+    - media: tuners: qt1010: replace BUG_ON with a regular error
+    - media: pci: cx23885: replace BUG with error return
+    - usb: cdns3: Put the cdns set active part outside the spin lock
+    - usb: gadget: fsl_qe_udc: validate endpoint index for ch9 udc
+    - tools: iio: iio_generic_buffer: Fix some integer type and calculation
+    - scsi: target: iscsi: Fix buffer overflow in lio_target_nacl_info_show()
+    - serial: cpm_uart: Avoid suspicious locking
+    - usb: ehci: add workaround for chipidea PORTSC.PEC bug
+    - media: pci: ipu3-cio2: Initialise timing struct to avoid a compiler warning
+    - kobject: Add sanity check for kset->kobj.ktype in kset_register()
+    - interconnect: Fix locking for runpm vs reclaim
+    - printk: Consolidate console deferred printing
+    - jbd2: refactor wait logic for transaction updates into a common function
+    - jbd2: fix use-after-free of transaction_t race
+    - jbd2: kill t_handle_lock transaction spinlock
+    - jbd2: rename jbd_debug() to jbd2_debug()
+    - jbd2: correct the end of the journal recovery scan range
+    - mtd: rawnand: brcmnand: Allow SoC to provide I/O operations
+    - mtd: rawnand: brcmnand: Fix ECC level field setting for v7.2 controller
+    - MIPS: Use "grep -E" instead of "egrep"
+    - perf test: Remove bash construct from stat_bpf_counters.sh test
+    - perf test shell stat_bpf_counters: Fix test on Intel
+    - btrfs: move btrfs_pinned_by_swapfile prototype into volumes.h
+    - btrfs: add a helper to read the superblock metadata_uuid
+    - btrfs: compare the correct fsid/metadata_uuid in btrfs_validate_super
+    - drm: gm12u320: Fix the timeout usage for usb_bulk_msg()
+    - scsi: qla2xxx: Fix NULL vs IS_ERR() bug for debugfs_create_dir()
+    - selftests: tracing: Fix to unmount tracefs for recovering environment
+    - scsi: lpfc: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
+    - x86/boot/compressed: Reserve more memory for page tables
+    - x86/purgatory: Remove LTO flags
+    - samples/hw_breakpoint: fix building without module unloading
+    - md/raid1: fix error: ISO C90 forbids mixed declarations
+    - attr: block mode changes of symlinks
+    - ovl: fix failed copyup of fileattr on a symlink
+    - ovl: fix incorrect fdput() on aio completion
+    - btrfs: fix lockdep splat and potential deadlock after failure running
+      delayed items
+    - btrfs: release path before inode lookup during the ino lookup ioctl
+    - tracing: Have tracing_max_latency inc the trace array ref count
+    - tracing: Have current_trace inc the trace array ref count
+    - tracing: Have option files inc the trace array ref count
+    - nfsd: fix change_info in NFSv4 RENAME replies
+    - tracefs: Add missing lockdown check to tracefs_create_dir()
+    - i2c: aspeed: Reset the i2c controller when timeout occurs
+    - ata: libata: disallow dev-initiated LPM transitions to unsupported states
+    - scsi: megaraid_sas: Fix deadlock on firmware crashdump
+    - scsi: pm8001: Setup IRQs on resume
+    - ext4: fix rec_len verify error
+    - drm/amd/display: fix the white screen issue when >= 64GB DRAM
+    - drm/amdgpu: fix amdgpu_cs_p1_user_fence
+    - drm/amd/display: enable cursor degamma for DCN3+ DRM legacy gamma
+    - interconnect: Teach lockdep about icc_bw_lock order
+    - Linux 5.15.133
+  * Jammy update: v5.15.132 upstream stable release (LP: #2041702)
+    - ARM: dts: imx: update sdma node name format
+    - ARM: dts: imx7s: Drop dma-apb interrupt-names
+    - ARM: dts: imx: Adjust dma-apbh node name
+    - ARM: dts: imx: Set default tuning step for imx7d usdhc
+    - phy: qcom-snps-femto-v2: use qcom_snps_hsphy_suspend/resume error code
+    - media: pulse8-cec: handle possible ping error
+    - media: pci: cx23885: fix error handling for cx23885 ATSC boards
+    - 9p: virtio: make sure 'offs' is initialized in zc_request
+    - ksmbd: fix out of bounds in smb3_decrypt_req()
+    - ksmbd: no response from compound read
+    - ASoC: da7219: Flush pending AAD IRQ when suspending
+    - ASoC: da7219: Check for failure reading AAD IRQ events
+    - ethernet: atheros: fix return value check in atl1c_tso_csum()
+    - vxlan: generalize vxlan_parse_gpe_hdr and remove unused args
+    - m68k: Fix invalid .section syntax
+    - s390/dasd: use correct number of retries for ERP requests
+    - s390/dasd: fix hanging device after request requeue
+    - fs/nls: make load_nls() take a const parameter
+    - ASoC: rt5682-sdw: fix for JD event handling in ClockStop Mode0
+    - ASoc: codecs: ES8316: Fix DMIC config
+    - ASoC: rt711: fix for JD event handling in ClockStop Mode0
+    - ASoC: rt711-sdca: fix for JD event handling in ClockStop Mode0
+    - ASoC: atmel: Fix the 8K sample parameter in I2SC master
+    - platform/x86: intel: hid: Always call BTNL ACPI method
+    - platform/x86/intel/hid: Add HP Dragonfly G2 to VGBS DMI quirks
+    - platform/x86: huawei-wmi: Silence ambient light sensor
+    - drm/amd/display: Exit idle optimizations before attempt to access PHY
+    - ovl: Always reevaluate the file signature for IMA
+    - ata: pata_arasan_cf: Use dev_err_probe() instead dev_err() in data_xfer()
+    - security: keys: perform capable check only on privileged operations
+    - kprobes: Prohibit probing on CFI preamble symbol
+    - clk: fixed-mmio: make COMMON_CLK_FIXED_MMIO depend on HAS_IOMEM
+    - vmbus_testing: fix wrong python syntax for integer value comparison
+    - net: usb: qmi_wwan: add Quectel EM05GV2
+    - wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
+    - idmaengine: make FSL_EDMA and INTEL_IDMA64 depends on HAS_IOMEM
+    - scsi: lpfc: Remove reftag check in DIF paths
+    - scsi: qedi: Fix potential deadlock on &qedi_percpu->p_work_lock
+    - net: hns3: restore user pause configure when disable autoneg
+    - drm/amdgpu: Match against exact bootloader status
+    - netlabel: fix shift wrapping bug in netlbl_catmap_setlong()
+    - bnx2x: fix page fault following EEH recovery
+    - sctp: handle invalid error codes without calling BUG()
+    - scsi: storvsc: Always set no_report_opcodes
+    - scsi: lpfc: Fix incorrect big endian type assignment in bsg loopback path
+    - ALSA: seq: oss: Fix racy open/close of MIDI devices
+    - tracing: Introduce pipe_cpumask to avoid race on trace_pipes
+    - platform/mellanox: Fix mlxbf-tmfifo not handling all virtio CONSOLE
+      notifications
+    - arm64: lib: Import latest version of Arm Optimized Routines' strncmp
+    - of: kexec: Mark ima_{free,stable}_kexec_buffer() as __init
+    - udf: Check consistency of Space Bitmap Descriptor
+    - udf: Handle error when adding extent to a file
+    - Revert "net: macsec: preserve ingress frame ordering"
+    - reiserfs: Check the return value from __getblk()
+    - eventfd: prevent underflow for eventfd semaphores
+    - fs: Fix error checking for d_hash_and_lookup()
+    - tmpfs: verify {g,u}id mount options correctly
+    - selftests/harness: Actually report SKIP for signal tests
+    - ARM: ptrace: Restore syscall restart tracing
+    - ARM: ptrace: Restore syscall skipping for tracers
+    - refscale: Fix uninitalized use of wait_queue_head_t
+    - OPP: Fix passing 0 to PTR_ERR in _opp_attach_genpd()
+    - selftests/resctrl: Make resctrl_tests run using kselftest framework
+    - selftests/resctrl: Add resctrl.h into build deps
+    - selftests/resctrl: Don't leak buffer in fill_cache()
+    - selftests/resctrl: Unmount resctrl FS if child fails to run benchmark
+    - selftests/resctrl: Close perf value read fd on errors
+    - x86/decompressor: Don't rely on upper 32 bits of GPRs being preserved
+    - perf/imx_ddr: don't enable counter0 if none of 4 counters are used
+    - selftests/futex: Order calls to futex_lock_pi
+    - s390/pkey: fix/harmonize internal keyblob headers
+    - s390/paes: fix PKEY_TYPE_EP11_AES handling for secure keyblobs
+    - ACPI: x86: s2idle: Post-increment variables when getting constraints
+    - ACPI: x86: s2idle: Fix a logic error parsing AMD constraints table
+    - x86/efistub: Fix PCI ROM preservation in mixed mode
+    - cpufreq: powernow-k8: Use related_cpus instead of cpus in driver.exit()
+    - bpftool: Use a local bpf_perf_event_value to fix accessing its fields
+    - bpf: Clear the probe_addr for uprobe
+    - tcp: tcp_enter_quickack_mode() should be static
+    - hwrng: nomadik - keep clock enabled while hwrng is registered
+    - hwrng: pic32 - use devm_clk_get_enabled
+    - regmap: rbtree: Use alloc_flags for memory allocations
+    - udp: re-score reuseport groups when connected sockets are present
+    - bpf: reject unhashed sockets in bpf_sk_assign
+    - ipv6: Add reasons for skb drops to __udp6_lib_rcv
+    - wifi: mt76: testmode: add nla_policy for MT76_TM_ATTR_TX_LENGTH
+    - spi: tegra20-sflash: fix to check return value of platform_get_irq() in
+      tegra_sflash_probe()
+    - can: gs_usb: gs_usb_receive_bulk_callback(): count RX overflow errors also
+      in case of OOM
+    - wifi: mt76: mt7915: fix power-limits while chan_switch
+    - wifi: mwifiex: Fix OOB and integer underflow when rx packets
+    - wifi: mwifiex: fix error recovery in PCIE buffer descriptor management
+    - crypto: stm32 - Properly handle pm_runtime_get failing
+    - crypto: api - Use work queue in crypto_destroy_instance
+    - Bluetooth: nokia: fix value check in nokia_bluetooth_serdev_probe()
+    - Bluetooth: Fix potential use-after-free when clear keys
+    - net: tcp: fix unexcepted socket die when snd_wnd is 0
+    - selftests/bpf: Clean up fmod_ret in bench_rename test script
+    - net-memcg: Fix scope of sockmem pressure indicators
+    - ice: ice_aq_check_events: fix off-by-one check when filling buffer
+    - crypto: caam - fix unchecked return value error
+    - hwrng: iproc-rng200 - Implement suspend and resume calls
+    - lwt: Fix return values of BPF xmit ops
+    - lwt: Check LWTUNNEL_XMIT_CONTINUE strictly
+    - fs: ocfs2: namei: check return value of ocfs2_add_entry()
+    - wifi: mwifiex: fix memory leak in mwifiex_histogram_read()
+    - wifi: mwifiex: Fix missed return in oob checks failed path
+    - samples/bpf: fix broken map lookup probe
+    - wifi: ath9k: fix races between ath9k_wmi_cmd and ath9k_wmi_ctrl_rx
+    - wifi: ath9k: protect WMI command response buffer replacement with a lock
+    - wifi: nl80211/cfg80211: add forgotten nla_policy for BSS color attribute
+    - wifi: mwifiex: avoid possible NULL skb pointer dereference
+    - Bluetooth: btusb: Do not call kfree_skb() under spin_lock_irqsave()
+    - wifi: ath9k: use IS_ERR() with debugfs_create_dir()
+    - net: arcnet: Do not call kfree_skb() under local_irq_disable()
+    - mlxsw: i2c: Fix chunk size setting in output mailbox buffer
+    - mlxsw: i2c: Limit single transaction buffer size
+    - hwmon: (tmp513) Fix the channel number in tmp51x_is_visible()
+    - netrom: Deny concurrent connect().
+    - drm/bridge: tc358764: Fix debug print parameter order
+    - quota: factor out dquot_write_dquot()
+    - quota: rename dquot_active() to inode_quota_active()
+    - quota: add new helper dquot_active()
+    - quota: fix dqput() to follow the guarantees dquot_srcu should provide
+    - ASoC: stac9766: fix build errors with REGMAP_AC97
+    - soc: qcom: ocmem: Add OCMEM hardware version print
+    - soc: qcom: ocmem: Fix NUM_PORTS & NUM_MACROS macros
+    - arm64: dts: qcom: sm8250: correct dynamic power coefficients
+    - arm64: dts: qcom: sm8250-edo: Add gpio line names for TLMM
+    - arm64: dts: qcom: sm8250-edo: Add GPIO line names for PMIC GPIOs
+    - arm64: dts: qcom: sm8250-edo: Rectify gpio-keys
+    - arm64: dts: qcom: msm8996: Add missing interrupt to the USB2 controller
+    - arm64: dts: qcom: sm8350: Add missing LMH interrupts to cpufreq
+    - arm64: dts: qcom: sm8350: Use proper CPU compatibles
+    - arm64: dts: qcom: pmk8350: fix ADC-TM compatible string
+    - arm64: dts: qcom: sm8250: Mark PCIe hosts as DMA coherent
+    - drm/amdgpu: avoid integer overflow warning in amdgpu_device_resize_fb_bar()
+    - ARM: dts: BCM53573: Add cells sizes to PCIe node
+    - ARM: dts: BCM53573: Use updated "spi-gpio" binding properties
+    - arm64: dts: qcom: sm8250-sony-xperia: correct GPIO keys wakeup again
+    - arm64: dts: qcom: pmi8998: Add node for WLED
+    - arm64: dts: qcom: correct SPMI WLED register range encoding
+    - arm64: dts: qcom: pm660l: Add missing short interrupt
+    - arm64: dts: qcom: pmi8994: Remove hardcoded linear WLED enabled-strings
+    - arm64: dts: qcom: Move WLED num-strings from pmi8994 to sony-xperia-tone
+    - arm64: dts: qcom: pmi8994: Add missing OVP interrupt
+    - drm/etnaviv: fix dumping of active MMU context
+    - x86/mm: Fix PAT bit missing from page protection modify mask
+    - ARM: dts: s3c64xx: align pinctrl with dtschema
+    - ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)
+    - ARM: dts: s5pv210: add dummy 5V regulator for backlight on SMDKv210
+    - ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)
+    - drm: adv7511: Fix low refresh rate register for ADV7533/5
+    - ARM: dts: BCM53573: Fix Ethernet info for Luxul devices
+    - arm64: dts: qcom: sdm845: Add missing RPMh power domain to GCC
+    - arm64: dts: qcom: sdm845: Fix the min frequency of "ice_core_clk"
+    - drm/amdgpu: Update min() to min_t() in 'amdgpu_info_ioctl'
+    - md/raid10: factor out dereference_rdev_and_rrdev()
+    - md/raid10: use dereference_rdev_and_rrdev() to get devices
+    - md/bitmap: don't set max_write_behind if there is no write mostly device
+    - md/md-bitmap: hold 'reconfig_mutex' in backlog_store()
+    - drm/msm: Update dev core dump to not print backwards
+    - drm/tegra: dpaux: Fix incorrect return value of platform_get_irq
+    - of: unittest: fix null pointer dereferencing in
+      of_unittest_find_node_by_name()
+    - arm64: dts: qcom: sm8150: Fix the I2C7 interrupt
+    - drm/armada: Fix off-by-one error in armada_overlay_get_property()
+    - drm/panel: simple: Add missing connector type and pixel format for AUO
+      T215HVN01
+    - ima: Remove deprecated IMA_TRUSTED_KEYRING Kconfig
+    - [Config] updateconfigs for IMA_TRUSTED_KEYRING
+    - drm: xlnx: zynqmp_dpsub: Add missing check for dma_set_mask
+    - drm/msm/mdp5: Don't leak some plane state
+    - firmware: meson_sm: fix to avoid potential NULL pointer dereference
+    - smackfs: Prevent underflow in smk_set_cipso()
+    - drm/amd/pm: fix variable dereferenced issue in amdgpu_device_attr_create()
+    - drm/msm/a2xx: Call adreno_gpu_init() earlier
+    - audit: fix possible soft lockup in __audit_inode_child()
+    - io_uring: fix drain stalls by invalid SQE
+    - bus: ti-sysc: Fix build warning for 64-bit build
+    - drm/mediatek: Remove freeing not dynamic allocated memory
+    - drm/mediatek: Fix potential memory leak if vmap() fail
+    - arm64: dts: qcom: apq8016-sbc: Fix ov5640 regulator supply names
+    - bus: ti-sysc: Fix cast to enum warning
+    - md: Set MD_BROKEN for RAID1 and RAID10
+    - md: add error_handlers for raid0 and linear
+    - md/raid0: Factor out helper for mapping and submitting a bio
+    - md/raid0: Fix performance regression for large sequential writes
+    - md: raid0: account for split bio in iostat accounting
+    - of: overlay: Call of_changeset_init() early
+    - of: unittest: Fix overlay type in apply/revert check
+    - ALSA: ac97: Fix possible error value of *rac97
+    - ipmi:ssif: Add check for kstrdup
+    - ipmi:ssif: Fix a memory leak when scanning for an adapter
+    - drivers: clk: keystone: Fix parameter judgment in _of_pll_clk_init()
+    - clk: sunxi-ng: Modify mismatched function name
+    - clk: qcom: gcc-sc7180: Fix up gcc_sdcc2_apps_clk_src
+    - EDAC/igen6: Fix the issue of no error events
+    - ext4: correct grp validation in ext4_mb_good_group
+    - ext4: avoid potential data overflow in next_linear_group
+    - clk: qcom: gcc-sm8250: Fix gcc_sdcc2_apps_clk_src
+    - clk: qcom: reset: Use the correct type of sleep/delay based on length
+    - clk: qcom: gcc-sm6350: Fix gcc_sdcc2_apps_clk_src
+    - PCI: microchip: Correct the DED and SEC interrupt bit offsets
+    - PCI: Mark NVIDIA T4 GPUs to avoid bus reset
+    - pinctrl: mcp23s08: check return value of devm_kasprintf()
+    - PCI: pciehp: Use RMW accessors for changing LNKCTL
+    - PCI/ASPM: Use RMW accessors for changing LNKCTL
+    - clk: imx8mp: fix sai4 clock
+    - clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
+    - powerpc/radix: Move some functions into #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
+    - vfio/type1: fix cap_migration information leak
+    - powerpc/fadump: reset dump area size if fadump memory reserve fails
+    - powerpc/perf: Convert fsl_emb notifier to state machine callbacks
+    - drm/amdgpu: Use RMW accessors for changing LNKCTL
+    - drm/radeon: Use RMW accessors for changing LNKCTL
+    - net/mlx5: Use RMW accessors for changing LNKCTL
+    - wifi: ath11k: Use RMW accessors for changing LNKCTL
+    - wifi: ath10k: Use RMW accessors for changing LNKCTL
+    - PCI: dwc: Add start_link/stop_link inlines
+    - PCI: layerscape: Add the endpoint linkup notifier support
+    - PCI: layerscape: Add workaround for lost link capabilities during reset
+    - powerpc: Don't include lppaca.h in paca.h
+    - powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
+    - nfs/blocklayout: Use the passed in gfp flags
+    - powerpc/iommu: Fix notifiers being shared by PCI and VIO buses
+    - ext4: fix unttached inode after power cut with orphan file feature enabled
+    - jfs: validate max amount of blocks before allocation.
+    - fs: lockd: avoid possible wrong NULL parameter
+    - NFSD: da_addr_body field missing in some GETDEVICEINFO replies
+    - NFS: Guard against READDIR loop when entry names exceed MAXNAMELEN
+    - NFSv4.2: fix handling of COPY ERR_OFFLOAD_NO_REQ
+    - pNFS: Fix assignment of xprtdata.cred
+    - RDMA/qedr: Remove a duplicate assignment in irdma_query_ah()
+    - media: ad5820: Drop unsupported ad5823 from i2c_ and of_device_id tables
+    - media: i2c: tvp5150: check return value of devm_kasprintf()
+    - media: v4l2-core: Fix a potential resource leak in v4l2_fwnode_parse_link()
+    - iommu/amd/iommu_v2: Fix pasid_state refcount dec hit 0 warning on pasid
+      unbind
+    - iommu: rockchip: Fix directory table address encoding
+    - drivers: usb: smsusb: fix error handling code in smsusb_init_device
+    - media: dib7000p: Fix potential division by zero
+    - media: dvb-usb: m920x: Fix a potential memory leak in m920x_i2c_xfer()
+    - media: cx24120: Add retval check for cx24120_message_send()
+    - scsi: hisi_sas: Modify v3 HW SSP underflow error processing
+    - scsi: hisi_sas: Modify v3 HW SATA completion error processing
+    - scsi: hisi_sas: Fix warnings detected by sparse
+    - scsi: hisi_sas: Fix normally completed I/O analysed as failed
+    - media: rkvdec: increase max supported height for H.264
+    - media: mediatek: vcodec: Return NULL if no vdec_fb is found
+    - usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()
+    - scsi: RDMA/srp: Fix residual handling
+    - scsi: iscsi: Rename iscsi_set_param() to iscsi_if_set_param()
+    - scsi: iscsi: Add length check for nlattr payload
+    - scsi: iscsi: Add strlen() check in iscsi_if_set{_host}_param()
+    - scsi: be2iscsi: Add length check when parsing nlattrs
+    - scsi: qla4xxx: Add length check when parsing nlattrs
+    - serial: sprd: Assign sprd_port after initialized to avoid wrong access
+    - serial: sprd: Fix DMA buffer leak issue
+    - x86/APM: drop the duplicate APM_MINOR_DEV macro
+    - scsi: qedf: Do not touch __user pointer in
+      qedf_dbg_stop_io_on_error_cmd_read() directly
+    - scsi: qedf: Do not touch __user pointer in qedf_dbg_debug_cmd_read()
+      directly
+    - scsi: qedf: Do not touch __user pointer in qedf_dbg_fp_int_cmd_read()
+      directly
+    - RDMA/irdma: Replace one-element array with flexible-array member
+    - coresight: tmc: Explicit type conversions to prevent integer overflow
+    - dma-buf/sync_file: Fix docs syntax
+    - driver core: test_async: fix an error code
+    - iommu/sprd: Add missing force_aperture
+    - RDMA/hns: Fix port active speed
+    - RDMA/hns: Fix incorrect post-send with direct wqe of wr-list
+    - RDMA/hns: Fix CQ and QP cache affinity
+    - IB/uverbs: Fix an potential error pointer dereference
+    - fsi: aspeed: Reset master errors after CFAM reset
+    - iommu/qcom: Disable and reset context bank before programming
+    - iommu/vt-d: Fix to flush cache of PASID directory table
+    - platform/x86: dell-sysman: Fix reference leak
+    - media: go7007: Remove redundant if statement
+    - media: venus: hfi_venus: Only consider sys_idle_indicator on V1
+    - USB: gadget: f_mass_storage: Fix unused variable warning
+    - media: ov5640: Enable MIPI interface in ov5640_set_power_mipi()
+    - media: i2c: ov2680: Set V4L2_CTRL_FLAG_MODIFY_LAYOUT on flips
+    - media: ov2680: Remove auto-gain and auto-exposure controls
+    - media: ov2680: Fix ov2680_bayer_order()
+    - media: ov2680: Fix vflip / hflip set functions
+    - media: ov2680: Remove VIDEO_V4L2_SUBDEV_API ifdef-s
+    - media: ov2680: Don't take the lock for try_fmt calls
+    - media: ov2680: Add ov2680_fill_format() helper function
+    - media: ov2680: Fix ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY not
+      working
+    - media: ov2680: Fix regulators being left enabled on ov2680_power_on() errors
+    - media: i2c: rdacm21: Fix uninitialized value
+    - cgroup:namespace: Remove unused cgroup_namespaces_init()
+    - scsi: core: Use 32-bit hostnum in scsi_host_lookup()
+    - scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock
+    - serial: tegra: handle clk prepare error in tegra_uart_hw_init()
+    - amba: bus: fix refcount leak
+    - Revert "IB/isert: Fix incorrect release of isert connection"
+    - HID: logitech-dj: Fix error handling in logi_dj_recv_switch_to_dj_mode()
+    - HID: multitouch: Correct devm device reference for hidinput input_dev name
+    - x86/speculation: Mark all Skylake CPUs as vulnerable to GDS
+    - tracing: Remove extra space at the end of hwlat_detector/mode
+    - tracing: Fix race issue between cpu buffer write and swap
+    - mtd: rawnand: brcmnand: Fix mtd oobsize
+    - phy/rockchip: inno-hdmi: use correct vco_div_5 macro on rk3328
+    - phy/rockchip: inno-hdmi: round fractal pixclock in rk3328 recalc_rate
+    - phy/rockchip: inno-hdmi: do not power on rk3328 post pll on reg write
+    - rpmsg: glink: Add check for kstrdup
+    - leds: pwm: Fix error code in led_pwm_create_fwnode()
+    - leds: multicolor: Use rounded division when calculating color components
+    - leds: trigger: tty: Do not use LED_ON/OFF constants, use
+      led_blink_set_oneshot instead
+    - mtd: spi-nor: Check bus width while setting QE bit
+    - mtd: rawnand: fsmc: handle clk prepare error in fsmc_nand_resume()
+    - um: Fix hostaudio build errors
+    - dmaengine: ste_dma40: Add missing IRQ check in d40_probe
+    - cpufreq: Fix the race condition while updating the transition_task of policy
+    - virtio_ring: fix avail_wrap_counter in virtqueue_add_packed
+    - skbuff: skb_segment, Call zero copy functions before using skbuff frags
+    - PM / devfreq: Fix leak in devfreq_dev_release()
+    - ALSA: pcm: Fix missing fixup call in compat hw_refine ioctl
+    - rcu: dump vmalloc memory info safely
+    - printk: ringbuffer: Fix truncating buffer size min_t cast
+    - scsi: core: Fix the scsi_set_resid() documentation
+    - mm/vmalloc: add a safer version of find_vm_area() for debug
+    - media: i2c: ccs: Check rules is non-NULL
+    - PCI: rockchip: Use 64-bit mask on MSI 64-bit PCI address
+    - ipmi_si: fix a memleak in try_smi_init()
+    - ARM: OMAP2+: Fix -Warray-bounds warning in _pwrdm_state_switch()
+    - backlight/gpio_backlight: Compare against struct fb_info.device
+    - backlight/bd6107: Compare against struct fb_info.device
+    - backlight/lv5207lp: Compare against struct fb_info.device
+    - xtensa: PMU: fix base address for the newer hardware
+    - i3c: master: svc: fix probe failure when no i3c device exist
+    - arm64: csum: Fix OoB access in IP checksum code for negative lengths
+    - media: dvb: symbol fixup for dvb_attach()
+    - media: venus: hfi_venus: Write to VIDC_CTRL_INIT after unmasking interrupts
+    - Revert "scsi: qla2xxx: Fix buffer overrun"
+    - scsi: mpt3sas: Perform additional retries if doorbell read returns 0
+    - ntb: Drop packets when qp link is down
+    - ntb: Clean up tx tail index on link down
+    - ntb: Fix calculation ntb_transport_tx_free_entry()
+    - Revert "PCI: Mark NVIDIA T4 GPUs to avoid bus reset"
+    - procfs: block chmod on /proc/thread-self/comm
+    - parisc: Fix /proc/cpuinfo output for lscpu
+    - dlm: fix plock lookup when using multiple lockspaces
+    - dccp: Fix out of bounds access in DCCP error handler
+    - X.509: if signature is unsupported skip validation
+    - net: handle ARPHRD_PPP in dev_is_mac_header_xmit()
+    - fsverity: skip PKCS#7 parser when keyring is empty
+    - mmc: renesas_sdhi: register irqs before registering controller
+    - pstore/ram: Check start of empty przs during init
+    - arm64: sdei: abort running SDEI handlers during crash
+    - s390/ipl: add missing secure/has_secure file to ipl type 'unknown'
+    - crypto: stm32 - fix loop iterating through scatterlist for DMA
+    - cpufreq: brcmstb-avs-cpufreq: Fix -Warray-bounds bug
+    - usb: typec: tcpm: set initial svdm version based on pd revision
+    - usb: typec: bus: verify partner exists in typec_altmode_attention
+    - x86/sgx: Break up long non-preemptible delays in sgx_vepc_release()
+    - perf/x86/uncore: Correct the number of CHAs on EMR
+    - tracing: Zero the pipe cpumask on alloc to avoid spurious -EBUSY
+    - md/md-bitmap: remove unnecessary local variable in backlog_store()
+    - udf: initialize newblock to 0
+    - net/ipv6: SKB symmetric hash should incorporate transport ports
+    - io_uring: always lock in io_apoll_task_func
+    - io_uring: break out of iowq iopoll on teardown
+    - io_uring: break iopolling on signal
+    - scsi: qla2xxx: Adjust IOCB resource on qpair create
+    - scsi: qla2xxx: Limit TMF to 8 per function
+    - scsi: qla2xxx: Fix deletion race condition
+    - scsi: qla2xxx: fix inconsistent TMF timeout
+    - scsi: qla2xxx: Fix command flush during TMF
+    - scsi: qla2xxx: Fix erroneous link up failure
+    - scsi: qla2xxx: Turn off noisy message log
+    - scsi: qla2xxx: Fix session hang in gnl
+    - scsi: qla2xxx: Fix TMF leak through
+    - scsi: qla2xxx: Remove unsupported ql2xenabledif option
+    - scsi: qla2xxx: Flush mailbox commands on chip reset
+    - scsi: qla2xxx: Fix smatch warn for qla_init_iocb_limit()
+    - scsi: qla2xxx: Error code did not return to upper layer
+    - scsi: qla2xxx: Fix firmware resource tracking
+    - fbdev/ep93xx-fb: Do not assign to struct fb_info.dev
+    - clk: qcom: camcc-sc7180: fix async resume during probe
+    - drm/ast: Fix DRAM init on AST2200
+    - clk: qcom: turingcc-qcs404: fix missing resume during probe
+    - lib/test_meminit: allocate pages up to order MAX_ORDER
+    - parisc: led: Fix LAN receive and transmit LEDs
+    - parisc: led: Reduce CPU overhead for disk & lan LED computation
+    - pinctrl: cherryview: fix address_space_handler() argument
+    - dt-bindings: clock: xlnx,versal-clk: drop select:false
+    - clk: qcom: gcc-mdm9615: use proper parent for pll0_vote clock
+    - soc: qcom: qmi_encdec: Restrict string length in decode
+    - clk: qcom: q6sstop-qcs404: fix missing resume during probe
+    - clk: qcom: mss-sc7180: fix missing resume during probe
+    - NFS: Fix a potential data corruption
+    - NFSv4/pnfs: minor fix for cleanup path in nfs4_get_device_info
+    - bus: mhi: host: Skip MHI reset if device is in RDDM
+    - kbuild: do not run depmod for 'make modules_sign'
+    - gfs2: Switch to wait_event in gfs2_logd
+    - gfs2: low-memory forced flush fixes
+    - kconfig: fix possible buffer overflow
+    - perf trace: Use zfree() to reduce chances of use after free
+    - perf trace: Really free the evsel->priv area
+    - pwm: atmel-tcb: Convert to platform remove callback returning void
+    - pwm: atmel-tcb: Harmonize resource allocation order
+    - pwm: atmel-tcb: Fix resource freeing in error path and remove
+    - backlight: gpio_backlight: Drop output GPIO direction check for initial
+      power state
+    - Input: tca6416-keypad - always expect proper IRQ number in i2c client
+    - Input: tca6416-keypad - fix interrupt enable disbalance
+    - perf annotate bpf: Don't enclose non-debug code with an assert()
+    - x86/virt: Drop unnecessary check on extended CPUID level in cpu_has_svm()
+    - perf vendor events: Update the JSON/events descriptions for power10 platform
+    - perf vendor events: Drop some of the JSON/events for power10 platform
+    - perf top: Don't pass an ERR_PTR() directly to perf_session__delete()
+    - watchdog: intel-mid_wdt: add MODULE_ALIAS() to allow auto-load
+    - pwm: lpc32xx: Remove handling of PWM channels
+    - net/sched: fq_pie: avoid stalls in fq_pie_timer()
+    - sctp: annotate data-races around sk->sk_wmem_queued
+    - ipv4: annotate data-races around fi->fib_dead
+    - net: read sk->sk_family once in sk_mc_loop()
+    - net: fib: avoid warn splat in flow dissector
+    - xsk: Fix xsk_diag use-after-free error during socket cleanup
+    - drm/i915/gvt: Drop unused helper intel_vgpu_reset_gtt()
+    - ipv4: ignore dst hint for multipath routes
+    - igb: disable virtualization features on 82580
+    - veth: Fixing transmit return status for dropped packets
+    - net: ipv6/addrconf: avoid integer underflow in ipv6_create_tempaddr
+    - net: phy: micrel: Correct bit assignments for phy_device flags
+    - af_unix: Fix data-races around user->unix_inflight.
+    - af_unix: Fix data-race around unix_tot_inflight.
+    - af_unix: Fix data-races around sk->sk_shutdown.
+    - af_unix: Fix data race around sk->sk_err.
+    - kcm: Destroy mutex in kcm_exit_net()
+    - octeontx2-af: Fix truncation of smq in CN10K NIX AQ enqueue mbox handler
+    - igc: Change IGC_MIN to allow set rx/tx value between 64 and 80
+    - igbvf: Change IGBVF_MIN to allow set rx/tx value between 64 and 80
+    - igb: Change IGB_MIN to allow set rx/tx value between 64 and 80
+    - s390/zcrypt: don't leak memory if dev_set_name() fails
+    - idr: fix param name in idr_alloc_cyclic() doc
+    - ip_tunnels: use DEV_STATS_INC()
+    - net: dsa: sja1105: fix bandwidth discrepancy between tc-cbs software and
+      offload
+    - net: dsa: sja1105: fix -ENOSPC when replacing the same tc-cbs too many times
+    - net: dsa: sja1105: complete tc-cbs offload support on SJA1110
+    - net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
+    - net: hns3: fix debugfs concurrency issue between kfree buffer and read
+    - net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
+    - net: hns3: fix the port information display when sfp is absent
+    - net: hns3: remove GSO partial feature bit
+    - sh: boards: Fix CEU buffer size passed to dma_declare_coherent_memory()
+    - net/mlx5: Free IRQ rmap and notifier on kernel shutdown
+    - ARC: atomics: Add compiler barrier to atomic operations...
+    - dmaengine: sh: rz-dmac: Fix destination and source data size setting
+    - jbd2: fix checkpoint cleanup performance regression
+    - jbd2: check 'jh->b_transaction' before removing it from checkpoint
+    - ext4: add correct group descriptors and reserved GDT blocks to system zone
+    - lib: test_scanf: Add explicit type cast to result initialization in
+      test_number_prefix()
+    - ata: pata_falcon: fix IO base selection for Q40
+    - ata: sata_gemini: Add missing MODULE_DESCRIPTION
+    - ata: pata_ftide010: Add missing MODULE_DESCRIPTION
+    - fuse: nlookup missing decrement in fuse_direntplus_link
+    - btrfs: free qgroup rsv on io failure
+    - btrfs: don't start transaction when joining with TRANS_JOIN_NOSTART
+    - btrfs: use the correct superblock to compare fsid in btrfs_validate_super
+    - mtd: rawnand: brcmnand: Fix crash during the panic_write
+    - mtd: rawnand: brcmnand: Fix potential out-of-bounds access in oob write
+    - mtd: rawnand: brcmnand: Fix potential false time out warning
+    - drm/amd/display: prevent potential division by zero errors
+    - MIPS: Fix CONFIG_CPU_DADDI_WORKAROUNDS `modules_install' regression
+    - perf hists browser: Fix hierarchy mode header
+    - perf tools: Handle old data in PERF_RECORD_ATTR
+    - perf hists browser: Fix the number of entries for 'e' key
+    - pcd: move the identify buffer into pcd_identify
+    - pcd: cleanup initialization
+    - block: move GENHD_FL_NATIVE_CAPACITY to disk->state
+    - block: move GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE to disk->event_flags
+    - block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART
+    - block: don't add or resize partition on the disk with GENHD_FL_NO_PART
+    - ARM: dts: samsung: exynos4210-i9100: Fix LCD screen's physical size
+    - ARM: dts: BCM5301X: Extend RAM to full 256MB for Linksys EA6500 V2
+    - net: ipv4: fix one memleak in __inet_del_ifa()
+    - kselftest/runner.sh: Propagate SIGTERM to runner child
+    - net/smc: use smc_lgr_list.lock to protect smc_lgr_list.list iterate in
+      smcr_port_add
+    - net: ethernet: mvpp2_main: fix possible OOB write in
+      mvpp2_ethtool_get_rxnfc()
+    - net: ethernet: mtk_eth_soc: fix possible NULL pointer dereference in
+      mtk_hwlro_get_fdir_all()
+    - hsr: Fix uninit-value access in fill_frame_info()
+    - net: dsa: sja1105: hide all multicast addresses from "bridge fdb show"
+    - r8152: check budget for r8152_poll()
+    - kcm: Fix memory leak in error path of kcm_sendmsg()
+    - platform/mellanox: mlxbf-tmfifo: Drop the Rx packet if no more descriptors
+    - platform/mellanox: mlxbf-tmfifo: Drop jumbo frames
+    - platform/mellanox: mlxbf-pmc: Fix potential buffer overflows
+    - platform/mellanox: mlxbf-pmc: Fix reading of unprogrammed events
+    - ipv6: fix ip6_sock_set_addr_preferences() typo
+    - ixgbe: fix timestamp configuration code
+    - kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
+    - MIPS: Only fiddle with CHECKFLAGS if `need-compiler'
+    - drm/amd/display: Fix a bug when searching for insert_above_mpcc
+    - pcd: fix error codes in pcd_init_unit()
+    - Linux 5.15.132
+  * CVE-2023-6176
+    - net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
+  * CVE-2023-6039
+    - timers: Use del_timer_sync() even on UP
+    - timers: Update kernel-doc for various functions
+    - timers: Rename del_timer_sync() to timer_delete_sync()
+    - timers: Rename del_timer() to timer_delete()
+    - timers: Split [try_to_]del_timer[_sync]() to prepare for shutdown mode
+    - timers: Add shutdown mechanism to the internal functions
+    - timers: Provide timer_shutdown[_sync]()
+    - clocksource/drivers/arm_arch_timer: Do not use timer namespace for
+      timer_shutdown() function
+    - clocksource/drivers/sp804: Do not use timer namespace for timer_shutdown()
+      function
+    - ARM: spear: Do not use timer namespace for timer_shutdown() function
+    - net: usb: lan78xx: reorder cleanup operations to avoid UAF bugs
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 21 Feb 2024 13:19:46 +1000
+
+linux-xilinx-zynqmp (5.15.0-1026.30) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1026.30 -proposed tracker (LP: #2049802)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] remove helper scripts
+    - debian/dkms-versions -- update from kernel-versions (main/d2024.01.02)
+
+  * Enable symbols for all Xilinx device trees (LP: #2049442)
+    - SAUCE: arm64: dts: Enable symbols for all Xilinx device trees
+
+  * Turn off non-zynqmp arch support (LP: #2044554)
+    - [Config] Turn off non-zynqmp arch support
+    - [Packaging] Update new baseline abi checks
+
+  * Add support for KD240 platform (LP: #2046280)
+    - Sync KD240 DTS from xlnx_rebase_v6.1_LTS
+    - can: xilinx_can: Add support for controller reset
+
+  [ Ubuntu: 5.15.0-92.102 ]
+
+  * jammy/linux: 5.15.0-92.102 -proposed tracker (LP: #2048614)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+  * CVE-2024-0193
+    - netfilter: nf_tables: skip set commit for deleted/destroyed sets
+  * CVE-2023-6040
+    - netfilter: nf_tables: Reject tables of unsupported family
+  * CVE-2023-6606
+    - smb: client: fix OOB in smbCalcSize()
+  * CVE-2023-6817
+    - netfilter: nft_set_pipapo: skip inactive elements during set walk
+  * CVE-2023-6932
+    - ipv4: igmp: fix refcnt uaf issue when receiving igmp query packet
+  * CVE-2023-6931
+    - perf/core: Add a new read format to get a number of lost samples
+    - perf: Fix perf_event_validate_size()
+    - perf: Fix perf_event_validate_size() lockdep splat
+
+  [ Ubuntu: 5.15.0-91.101 ]
+
+  * jammy/linux: 5.15.0-91.101 -proposed tracker (LP: #2043452)
+  * USB bus error after upgrading to proposed kernel on lunar and jammy
+    (LP: #2043197)
+    - USB: core: Fix oversight in SuperSpeed initialization
+
+  [ Ubuntu: 5.15.0-90.100 ]
+
+  * jammy/linux: 5.15.0-90.100 -proposed tracker (LP: #2041603)
+  * CVE-2023-25775
+    - RDMA/irdma: Remove irdma_uk_mw_bind()
+    - RDMA/irdma: Remove irdma_sc_send_lsmm_nostag()
+    - RDMA/irdma: Remove irdma_cqp_up_map_cmd()
+    - RDMA/irdma: Remove irdma_get_hw_addr()
+    - RDMA/irdma: Make irdma_uk_cq_init() return a void
+    - RDMA/irdma: optimize rx path by removing unnecessary copy
+    - RDMA/irdma: Remove enum irdma_status_code
+    - RDMA/irdma: Remove excess error variables
+    - RDMA/irdma: Prevent zero-length STAG registration
+  * CVE-2023-39189
+    - netfilter: nfnetlink_osf: avoid OOB read
+  * SMC stats: Wrong bucket calculation for payload of exactly 4096 bytes
+    (LP: #2039575)
+    - net/smc: Fix pos miscalculation in statistics
+  * CVE-2023-45871
+    - igb: set max size RX buffer when store bad packet is enabled
+  * CVE-2023-39193
+    - netfilter: xt_sctp: validate the flag_info count
+  * CVE-2023-39192
+    - netfilter: xt_u32: validate user space input
+  * CVE-2023-31085
+    - ubi: Refuse attaching if mtd's erasesize is 0
+  * CVE-2023-5717
+    - perf: Disallow mis-matched inherited group reads
+  * CVE-2023-5178
+    - nvmet-tcp: Fix a possible UAF in queue intialization setup
+  * CVE-2023-5158
+    - vringh: don't use vringh_kiov_advance() in vringh_iov_xfer()
+  * [SRU][J/L/M] UBUNTU: [Packaging] Make WWAN driver a loadable module
+    (LP: #2033406)
+    - [Packaging] Make WWAN driver loadable modules
+  * HP ProBook 450 G8 Notebook fail to wifi test (LP: #2037513)
+    - iwlwifi: mvm: Don't fail if PPAG isn't supported
+    - wifi: iwlwifi: fw: skip PPAG for JF
+  * usbip: error: failed to open /usr/share/hwdata//usb.ids (LP: #2039439)
+    - [Packaging] Make linux-tools-common depend on hwdata
+  * scripts/pahole-flags.sh change return to exit 0 (LP: #2035123)
+    - SAUCE: scripts/pahole-flags.sh change return to exit 0
+  * Unable to use nvme drive to install Ubuntu 23.10 (LP: #2040157)
+    - misc: rtsx: Fix some platforms can not boot and move the l1ss judgment to
+      probe
+  * Jammy update: v5.15.131 upstream stable release (LP: #2039610)
+    - erofs: ensure that the post-EOF tails are all zeroed
+    - ksmbd: fix wrong DataOffset validation of create context
+    - ksmbd: replace one-element array with flex-array member in struct
+      smb2_ea_info
+    - ARM: pxa: remove use of symbol_get()
+    - mmc: au1xmmc: force non-modular build and remove symbol_get usage
+    - net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index
+    - rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff
+    - modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules
+    - USB: serial: option: add Quectel EM05G variant (0x030e)
+    - USB: serial: option: add FOXCONN T99W368/T99W373 product
+    - ALSA: usb-audio: Fix init call orders for UAC1
+    - usb: dwc3: meson-g12a: do post init to fix broken usb after resumption
+    - usb: chipidea: imx: improve logic if samsung,picophy-* parameter is 0
+    - HID: wacom: remove the battery when the EKR is off
+    - staging: rtl8712: fix race condition
+    - Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race
+      condition
+    - wifi: mt76: mt7921: do not support one stream on secondary antenna only
+    - serial: qcom-geni: fix opp vote on shutdown
+    - serial: sc16is7xx: fix broken port 0 uart init
+    - serial: sc16is7xx: fix bug when first setting GPIO direction
+    - firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe
+    - fsi: master-ast-cf: Add MODULE_FIRMWARE macro
+    - tcpm: Avoid soft reset when partner does not support get_status
+    - nilfs2: fix general protection fault in nilfs_lookup_dirty_data_buffers()
+    - nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
+    - pinctrl: amd: Don't show `Invalid config param` errors
+    - usb: typec: tcpci: move tcpci.h to include/linux/usb/
+    - usb: typec: tcpci: clear the fault status bit
+    - Linux 5.15.131
+  * Jammy update: v5.15.130 upstream stable release (LP: #2039608)
+    - ACPI: thermal: Drop nocrt parameter
+    - module: Expose module_init_layout_section()
+    - arm64: module-plts: inline linux/moduleloader.h
+    - arm64: module: Use module_init_layout_section() to spot init sections
+    - ARM: module: Use module_init_layout_section() to spot init sections
+    - rcu: Prevent expedited GP from enabling tick on offline CPU
+    - rcu-tasks: Fix IPI failure handling in trc_wait_for_one_reader
+    - rcu-tasks: Wait for trc_read_check_handler() IPIs
+    - rcu-tasks: Add trc_inspect_reader() checks for exiting critical section
+    - Linux 5.15.130
+  * CVE-2023-42754
+    - ipv4: fix null-deref in ipv4_link_failure
+  * Jammy update: v5.15.129 upstream stable release (LP: #2039227)
+    - NFSv4.2: fix error handling in nfs42_proc_getxattr
+    - NFSv4: fix out path in __nfs4_get_acl_uncached
+    - xprtrdma: Remap Receive buffers after a reconnect
+    - PCI: acpiphp: Reassign resources on bridge if necessary
+    - dlm: improve plock logging if interrupted
+    - dlm: replace usage of found with dedicated list iterator variable
+    - fs: dlm: add pid to debug log
+    - fs: dlm: change plock interrupted message to debug again
+    - fs: dlm: use dlm_plock_info for do_unlock_close
+    - fs: dlm: fix mismatch of plock results from userspace
+    - MIPS: cpu-features: Enable octeon_cache by cpu_type
+    - MIPS: cpu-features: Use boot_cpu_type for CPU type based features
+    - fbdev: Improve performance of sys_imageblit()
+    - fbdev: Fix sys_imageblit() for arbitrary image widths
+    - fbdev: fix potential OOB read in fast_imageblit()
+    - ALSA: pcm: Fix potential data race at PCM memory allocation helpers
+    - jbd2: remove t_checkpoint_io_list
+    - jbd2: remove journal_clean_one_cp_list()
+    - jbd2: fix a race when checking checkpoint buffer busy
+    - can: raw: fix receiver memory leak
+    - drm/amd/display: do not wait for mpc idle if tg is disabled
+    - drm/amd/display: check TG is non-null before checking if enabled
+    - can: raw: fix lockdep issue in raw_release()
+    - tracing: Fix cpu buffers unavailable due to 'record_disabled' missed
+    - tracing: Fix memleak due to race between current_tracer and trace
+    - octeontx2-af: SDP: fix receive link config
+    - sock: annotate data-races around prot->memory_pressure
+    - dccp: annotate data-races in dccp_poll()
+    - ipvlan: Fix a reference count leak warning in ipvlan_ns_exit()
+    - net: bgmac: Fix return value check for fixed_phy_register()
+    - net: bcmgenet: Fix return value check for fixed_phy_register()
+    - net: validate veth and vxcan peer ifindexes
+    - ice: fix receive buffer size miscalculation
+    - igb: Avoid starting unnecessary workqueues
+    - igc: Fix the typo in the PTM Control macro
+    - net/sched: fix a qdisc modification with ambiguous command request
+    - netfilter: nf_tables: flush pending destroy work before netlink notifier
+    - netfilter: nf_tables: fix out of memory error handling
+    - rtnetlink: return ENODEV when ifname does not exist and group is given
+    - rtnetlink: Reject negative ifindexes in RTM_NEWLINK
+    - net: remove bond_slave_has_mac_rcu()
+    - bonding: fix macvlan over alb bond support
+    - net/ncsi: make one oem_gma function for all mfr id
+    - net/ncsi: change from ndo_set_mac_address to dev_set_mac_address
+    - ibmveth: Use dcbf rather than dcbfl
+    - NFSv4: Fix dropped lock for racing OPEN and delegation return
+    - clk: Fix slab-out-of-bounds error in devm_clk_release()
+    - ALSA: ymfpci: Fix the missing snd_card_free() call at probe error
+    - mm: add a call to flush_cache_vmap() in vmap_pfn()
+    - NFS: Fix a use after free in nfs_direct_join_group()
+    - nfsd: Fix race to FREE_STATEID and cl_revoked
+    - selinux: set next pointer before attaching to list
+    - batman-adv: Trigger events for auto adjusted MTU
+    - batman-adv: Don't increase MTU when set by user
+    - batman-adv: Do not get eth header before batadv_check_management_packet
+    - batman-adv: Fix TT global entry leak when client roamed back
+    - batman-adv: Fix batadv_v_ogm_aggr_send memory leak
+    - batman-adv: Hold rtnl lock during MTU update via netlink
+    - lib/clz_ctz.c: Fix __clzdi2() and __ctzdi2() for 32-bit kernels
+    - radix tree: remove unused variable
+    - of: unittest: Fix EXPECT for parse_phandle_with_args_map() test
+    - of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock
+    - media: vcodec: Fix potential array out-of-bounds in encoder queue_setup
+    - PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root
+      bus
+    - drm/vmwgfx: Fix shader stage validation
+    - drm/display/dp: Fix the DP DSC Receiver cap size
+    - x86/fpu: Invalidate FPU state correctly on exec()
+    - nfs: use vfs setgid helper
+    - nfsd: use vfs setgid helper
+    - torture: Fix hang during kthread shutdown phase
+    - cgroup/cpuset: Rename functions dealing with DEADLINE accounting
+    - sched/cpuset: Bring back cpuset_mutex
+    - sched/cpuset: Keep track of SCHED_DEADLINE task in cpusets
+    - cgroup/cpuset: Iterate only if DEADLINE tasks are present
+    - sched/deadline: Create DL BW alloc, free & check overflow interface
+    - cgroup/cpuset: Free DL BW in case can_attach() fails
+    - drm/i915: Fix premature release of request's reusable memory
+    - can: raw: add missing refcount for memory leak fix
+    - scsi: snic: Fix double free in snic_tgt_create()
+    - scsi: core: raid_class: Remove raid_component_add()
+    - clk: Fix undefined reference to `clk_rate_exclusive_{get,put}'
+    - pinctrl: renesas: rza2: Add lock around
+      pinctrl_generic{{add,remove}_group,{add,remove}_function}
+    - dma-buf/sw_sync: Avoid recursive lock during fence signal
+    - mm: memory-failure: kill soft_offline_free_page()
+    - mm: memory-failure: fix unexpected return value in soft_offline_page()
+    - mm,ima,kexec,of: use memblock_free_late from ima_free_kexec_buffer
+    - Linux 5.15.129
+  * Jammy update: v5.15.128 upstream stable release (LP: #2038486)
+    - mmc: sdhci-f-sdh30: Replace with sdhci_pltfm
+    - selftests: forwarding: tc_actions: cleanup temporary files when test is
+      aborted
+    - selftests: forwarding: tc_actions: Use ncat instead of nc
+    - macsec: Fix traffic counters/statistics
+    - macsec: use DEV_STATS_INC()
+    - net/tls: Perform immediate device ctx cleanup when possible
+    - net/tls: Multi-threaded calls to TX tls_dev_del
+    - net: tls: avoid discarding data on record close
+    - PCI: tegra194: Fix possible array out of bounds access
+    - ARM: dts: imx6dl: prtrvt, prtvt7, prti6q, prtwd2: fix USB related warnings
+    - iopoll: Call cpu_relax() in busy loops
+    - ASoC: SOF: Intel: fix SoundWire/HDaudio mutual exclusion
+    - dma-remap: use kvmalloc_array/kvfree for larger dma memory remap
+    - HID: logitech-hidpp: Add USB and Bluetooth IDs for the Logitech G915 TKL
+      Keyboard
+    - HID: add quirk for 03f0:464a HP Elite Presenter Mouse
+    - RDMA/mlx5: Return the firmware result upon destroying QP/RQ
+    - ovl: check type and offset of struct vfsmount in ovl_entry
+    - smb: client: fix warning in cifs_smb3_do_mount()
+    - media: v4l2-mem2mem: add lock to protect parameter num_rdy
+    - usb: gadget: u_serial: Avoid spinlock recursion in __gs_console_push
+    - media: platform: mediatek: vpu: fix NULL ptr dereference
+    - thunderbolt: Read retimer NVM authentication status prior
+      tb_retimer_set_inbound_sbtx()
+    - usb: chipidea: imx: don't request QoS for imx8ulp
+    - usb: chipidea: imx: add missing USB PHY DPDM wakeup setting
+    - gfs2: Fix possible data races in gfs2_show_options()
+    - pcmcia: rsrc_nonstatic: Fix memory leak in nonstatic_release_resource_db()
+    - firewire: net: fix use after free in fwnet_finish_incoming_packet()
+    - watchdog: sp5100_tco: support Hygon FCH/SCH (Server Controller Hub)
+    - Bluetooth: L2CAP: Fix use-after-free
+    - Bluetooth: btusb: Add MT7922 bluetooth ID for the Asus Ally
+    - drm/amdgpu: Fix potential fence use-after-free v2
+    - fs/ntfs3: Enhance sanity check while generating attr_list
+    - fs: ntfs3: Fix possible null-pointer dereferences in mi_read()
+    - fs/ntfs3: Mark ntfs dirty when on-disk struct is corrupted
+    - ALSA: hda/realtek: Add quirks for Unis H3C Desktop B760 & Q760
+    - ALSA: hda: fix a possible null-pointer dereference due to data race in
+      snd_hdac_regmap_sync()
+    - powerpc/kasan: Disable KCOV in KASAN code
+    - ring-buffer: Do not swap cpu_buffer during resize process
+    - iio: add addac subdirectory
+    - iio: adc: stx104: Utilize iomap interface
+    - iio: adc: stx104: Implement and utilize register structures
+    - iio: stx104: Move to addac subdirectory
+    - iio: addac: stx104: Fix race condition for stx104_write_raw()
+    - iio: addac: stx104: Fix race condition when converting analog-to-digital
+    - igc: read before write to SRRCTL register
+    - ARM: dts: aspeed: asrock: Correct firmware flash SPI clocks
+    - drm/amd/display: save restore hdcp state when display is unplugged from mst
+      hub
+    - drm/amd/display: phase3 mst hdcp for multiple displays
+    - drm/amd/display: fix access hdcp_workqueue assert
+    - usb: dwc3: gadget: Synchronize IRQ between soft connect/disconnect
+    - usb: dwc3: Remove DWC3 locking during gadget suspend/resume
+    - usb: dwc3: Fix typos in gadget.c
+    - USB: dwc3: gadget: drop dead hibernation code
+    - usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()
+    - tty: serial: fsl_lpuart: Add i.MXRT1050 support
+    - tty: serial: fsl_lpuart: make rx_watermark configurable for different
+      platforms
+    - tty: serial: fsl_lpuart: reduce RX watermark to 0 on LS1028A
+    - USB: dwc3: qcom: fix NULL-deref on suspend
+    - USB: dwc3: fix use-after-free on core driver unbind
+    - mmc: bcm2835: fix deferred probing
+    - mmc: sunxi: fix deferred probing
+    - ARM: dts: imx6sll: fixup of operating points
+    - ARM: dts: nxp/imx6sll: fix wrong property name in usbphy node
+    - btrfs: move out now unused BG from the reclaim list
+    - virtio-mmio: don't break lifecycle of vm_dev
+    - vduse: Use proper spinlock for IRQ injection
+    - cifs: fix potential oops in cifs_oplock_break
+    - i2c: bcm-iproc: Fix bcm_iproc_i2c_isr deadlock issue
+    - i2c: hisi: Only handle the interrupt of the driver's transfer
+    - fbdev: mmp: fix value check in mmphw_probe()
+    - powerpc/rtas_flash: allow user copy to flash block cache objects
+    - tty: n_gsm: fix the UAF caused by race condition in gsm_cleanup_mux
+    - tty: serial: fsl_lpuart: Clear the error flags by writing 1 for lpuart32
+      platforms
+    - btrfs: fix BUG_ON condition in btrfs_cancel_balance
+    - i2c: designware: Correct length byte validation logic
+    - i2c: designware: Handle invalid SMBus block data response length value
+    - net: xfrm: Fix xfrm_address_filter OOB read
+    - net: af_key: fix sadb_x_filter validation
+    - net: xfrm: Amend XFRMA_SEC_CTX nla_policy structure
+    - xfrm: fix slab-use-after-free in decode_session6
+    - ip6_vti: fix slab-use-after-free in decode_session6
+    - ip_vti: fix potential slab-use-after-free in decode_session6
+    - xfrm: add forgotten nla_policy for XFRMA_MTIMER_THRESH
+    - net: phy: fix IRQ-based wake-on-lan over hibernate / power off
+    - selftests: mirror_gre_changes: Tighten up the TTL test match
+    - drm/panel: simple: Fix AUO G121EAN01 panel timings according to the docs
+    - netfilter: nf_tables: fix false-positive lockdep splat
+    - ipvs: fix racy memcpy in proc_do_sync_threshold
+    - net: phy: broadcom: stub c45 read/write for 54810
+    - team: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
+    - iavf: fix FDIR rule fields masks validation
+    - i40e: fix misleading debug logs
+    - net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset
+    - sock: Fix misuse of sk_under_memory_pressure()
+    - net: do not allow gso_size to be set to GSO_BY_FRAGS
+    - bus: ti-sysc: Flush posted write on enable before reset
+    - arm64: dts: qcom: qrb5165-rb5: fix thermal zone conflict
+    - ARM: dts: imx: Set default tuning step for imx6sx usdhc
+    - ASoC: rt5665: add missed regulator_bulk_disable
+    - ASoC: meson: axg-tdm-formatter: fix channel slot allocation
+    - soc: aspeed: socinfo: Add kfree for kstrdup
+    - ALSA: hda/realtek - Remodified 3k pull low procedure
+    - riscv: uaccess: Return the number of bytes effectively not copied
+    - serial: 8250: Fix oops for port->pm on uart_change_pm()
+    - ALSA: usb-audio: Add support for Mythware XA001AU capture and playback
+      interfaces.
+    - cifs: Release folio lock on fscache read hit.
+    - mmc: wbsd: fix double mmc_free_host() in wbsd_init()
+    - mmc: block: Fix in_flight[issue_type] value error
+    - drm/qxl: fix UAF on handle creation
+    - drm/amd: flush any delayed gfxoff on suspend entry
+    - netfilter: set default timeout to 3 secs for sctp shutdown send and recv
+      state
+    - arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4
+    - virtio-net: set queues after driver_ok
+    - net: fix the RTO timer retransmitting skb every 1ms if linear option is
+      enabled
+    - mmc: f-sdh30: fix order of function calls in sdhci_f_sdh30_remove
+    - Linux 5.15.128
+  * Jammy update: v5.15.127 upstream stable release (LP: #2038382)
+    - ksmbd: validate command request size
+    - ksmbd: fix wrong next length validation of ea buffer in smb2_set_ea()
+    - wireguard: allowedips: expand maximum node depth
+    - mmc: moxart: read scr register without changing byte order
+    - ipv6: adjust ndisc_is_useropt() to also return true for PIO
+    - dmaengine: pl330: Return DMA_PAUSED when transaction is paused
+    - riscv,mmio: Fix readX()-to-delay() ordering
+    - drm/nouveau/gr: enable memory loads on helper invocation on all channels
+    - drm/shmem-helper: Reset vma->vm_ops before calling dma_buf_mmap()
+    - drm/amd/display: check attr flag before set cursor degamma on DCN3+
+    - hwmon: (pmbus/bel-pfe) Enable PMBUS_SKIP_STATUS_CHECK for pfe1100
+    - radix tree test suite: fix incorrect allocation size for pthreads
+    - nilfs2: fix use-after-free of nilfs_root in dirtying inodes via iput
+    - bpf: allow precision tracking for programs with subprogs
+    - bpf: stop setting precise in current state
+    - bpf: aggressively forget precise markings during state checkpointing
+    - selftests/bpf: make test_align selftest more robust
+    - selftests/bpf: Workaround verification failure for
+      fexit_bpf2bpf/func_replace_return_code
+    - selftests/bpf: Fix sk_assign on s390x
+    - io_uring: correct check for O_TMPFILE
+    - iio: cros_ec: Fix the allocation size for cros_ec_command
+    - iio: adc: ina2xx: avoid NULL pointer dereference on OF device match
+    - binder: fix memory leak in binder_init()
+    - misc: rtsx: judge ASPM Mode to set PETXCFG Reg
+    - usb-storage: alauda: Fix uninit-value in alauda_check_media()
+    - usb: dwc3: Properly handle processing of pending events
+    - usb: common: usb-conn-gpio: Prevent bailing out if initial role is none
+    - usb: typec: tcpm: Fix response to vsafe0V event
+    - x86/cpu/amd: Enable Zenbleed fix for AMD Custom APU 0405
+    - x86/mm: Fix VDSO and VVAR placement on 5-level paging machines
+    - x86/speculation: Add cpu_show_gds() prototype
+    - x86: Move gds_ucode_mitigated() declaration to header
+    - drm/nouveau/disp: Revert a NULL check inside nouveau_connector_get_modes
+    - selftests/rseq: Fix build with undefined __weak
+    - selftests: forwarding: Add a helper to skip test when using veth pairs
+    - selftests: forwarding: ethtool: Skip when using veth pairs
+    - selftests: forwarding: ethtool_extended_state: Skip when using veth pairs
+    - selftests: forwarding: Skip test when no interfaces are specified
+    - selftests: forwarding: Switch off timeout
+    - selftests: forwarding: tc_flower: Relax success criterion
+    - net: core: remove unnecessary frame_sz check in bpf_xdp_adjust_tail()
+    - bpf, sockmap: Fix map type error in sock_map_del_link
+    - bpf, sockmap: Fix bug that strp_done cannot be called
+    - mISDN: Update parameter type of dsp_cmx_send()
+    - net/packet: annotate data-races around tp->status
+    - tunnels: fix kasan splat when generating ipv4 pmtu error
+    - xsk: fix refcount underflow in error path
+    - bonding: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
+    - dccp: fix data-race around dp->dccps_mss_cache
+    - drivers: net: prevent tun_build_skb() to exceed the packet size limit
+    - iavf: fix potential races for FDIR filters
+    - IB/hfi1: Fix possible panic during hotplug remove
+    - drm/rockchip: Don't spam logs in atomic check
+    - wifi: cfg80211: fix sband iftype data lookup for AP_VLAN
+    - RDMA/umem: Set iova in ODP flow
+    - net: phy: at803x: remove set/get wol callbacks for AR8032
+    - net: hns3: refactor hclge_mac_link_status_wait for interface reuse
+    - net: hns3: add wait until mac link down
+    - nexthop: Fix infinite nexthop dump when using maximum nexthop ID
+    - nexthop: Make nexthop bucket dump more efficient
+    - nexthop: Fix infinite nexthop bucket dump when using maximum nexthop ID
+    - dmaengine: mcf-edma: Fix a potential un-allocated memory access
+    - net/mlx5: Allow 0 for total host VFs
+    - net/mlx5: Skip clock update work when device is in error state
+    - ibmvnic: Enforce stronger sanity checks on login response
+    - ibmvnic: Unmap DMA login rsp buffer on send login fail
+    - ibmvnic: Handle DMA unmapping of login buffs in release functions
+    - btrfs: don't stop integrity writeback too early
+    - btrfs: exit gracefully if reloc roots don't match
+    - btrfs: reject invalid reloc tree root keys with stack dump
+    - btrfs: set cache_block_group_error if we find an error
+    - nvme-tcp: fix potential unbalanced freeze & unfreeze
+    - nvme-rdma: fix potential unbalanced freeze & unfreeze
+    - netfilter: nf_tables: report use refcount overflow
+    - scsi: core: Fix legacy /proc parsing buffer overflow
+    - scsi: storvsc: Fix handling of virtual Fibre Channel timeouts
+    - scsi: 53c700: Check that command slot is not NULL
+    - scsi: snic: Fix possible memory leak if device_add() fails
+    - scsi: core: Fix possible memory leak if device_add() fails
+    - scsi: fnic: Replace return codes in fnic_clean_pending_aborts()
+    - scsi: qedi: Fix firmware halt over suspend and resume
+    - scsi: qedf: Fix firmware halt over suspend and resume
+    - alpha: remove __init annotation from exported page_is_ram()
+    - sch_netem: fix issues in netem_change() vs get_dist_table()
+    - tick: Detect and fix jiffies update stall
+    - timers/nohz: Switch to ONESHOT_STOPPED in the low-res handler when the tick
+      is stopped
+    - timers/nohz: Last resort update jiffies on nohz_full IRQ entry
+    - Linux 5.15.127
+    - Upstream stable to v5.15.127
+  * CVE-2023-37453
+    - USB: core: Unite old scheme and new scheme descriptor reads
+    - USB: core: Change usb_get_device_descriptor() API
+    - USB: core: Fix race by not overwriting udev->descriptor in hub_port_init()
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 19 Jan 2024 12:03:51 +1000
+
+linux-xilinx-zynqmp (5.15.0-1025.29) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1025.29 -proposed tracker (LP: #2036376)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - debian/dkms-versions -- update from kernel-versions (main/d2023.10.10)
+
+  * Jammy update: v5.15.117 upstream stable release (LP: #2030107)
+    - [Config] updateconfigs for BLK_DEV_SX8
+
+  * Jammy update: v5.15.118 upstream stable release (LP: #2030239)
+    - [Config] updateconfigs for DECNET
+
+  * CVE-2023-42755
+    - [Config] remove NET_CLS_RSVP and NET_CLS_RSVP6
+
+  * Please enable Renesas RZ platform serial installer (LP: #2022361)
+    - [Config] Mark sh-sci as built-in
+
+  * Jammy update: v5.15.107 upstream stable release (LP: #2023320)
+    - [Config] updateconfigs for ns module merger
+
+  * Jammy update: v5.15.105 upstream stable release (LP: #2023230)
+    - [Config] updateconfigs for SERIAL_8250_ASPEED_VUART
+
+  * Add K24 device tree (LP: #2040354)
+    - SAUCE: arm64: zynqmp: Add K24 device trees
+    - SAUCE: arm64: dts: Build dtbs for k24 carrier board
+
+  * K26 QSPI MTD Definition Correction (LP: #2032972)
+    - arm64: zynqmp: Fix User MTD partition size
+
+  * Move experimental ubuntu drivers to staging (LP: #2036370)
+    - ubuntu/staging: Move out of tree Xilinx drivers into staging directory
+    - modpost: Add staging flag to drivers in ubuntu/staging
+
+  * [kr260] Kernel snap does not boot (LP: #2028505)
+    - Fix kernel snap to support KR260
+
+  [ Ubuntu: 5.15.0-88.98 ]
+
+  * jammy/linux: 5.15.0-88.98 -proposed tracker (LP: #2038055)
+  * CVE-2023-4244
+    - netfilter: nf_tables: don't skip expired elements during walk
+    - netfilter: nf_tables: adapt set backend to use GC transaction API
+    - netfilter: nft_set_hash: mark set element as dead when deleting from packet
+      path
+    - netfilter: nf_tables: GC transaction API to avoid race with control plane
+    - netfilter: nf_tables: remove busy mark and gc batch API
+    - netfilter: nf_tables: don't fail inserts if duplicate has expired
+    - netfilter: nf_tables: fix kdoc warnings after gc rework
+    - netfilter: nf_tables: fix GC transaction races with netns and netlink event
+      exit path
+    - netfilter: nf_tables: GC transaction race with netns dismantle
+    - netfilter: nf_tables: GC transaction race with abort path
+    - netfilter: nf_tables: use correct lock to protect gc_list
+    - netfilter: nf_tables: defer gc run if previous batch is still pending
+    - netfilter: nft_dynset: disallow object maps
+    - netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
+  * CVE-2023-42756
+    - netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
+  * CVE-2023-4623
+    - net/sched: sch_hfsc: Ensure inner classes have fsc curve
+  * PCI BARs larger than 128GB are disabled (LP: #2037403)
+    - PCI: Support BAR sizes up to 8TB
+  * Fix unstable audio at low levels on Thinkpad P1G4 (LP: #2037077)
+    - ALSA: hda/realtek - ALC287 I2S speaker platform support
+  * Check for changes relevant for security certifications (LP: #1945989)
+    - [Packaging] Add a new fips-checks script
+  * Jammy update: v5.15.126 upstream stable release (LP: #2037593)
+    - io_uring: gate iowait schedule on having pending requests
+    - perf: Fix function pointer case
+    - net/mlx5: Free irqs only on shutdown callback
+    - arm64: errata: Add workaround for TSB flush failures
+    - arm64: errata: Add detection for TRBE write to out-of-range
+    - [Config] updateconfigs for ARM64_ERRATUM_ and
+      ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+    - iommu/arm-smmu-v3: Work around MMU-600 erratum 1076982
+    - iommu/arm-smmu-v3: Document MMU-700 erratum 2812531
+    - iommu/arm-smmu-v3: Add explicit feature for nesting
+    - iommu/arm-smmu-v3: Document nesting-related errata
+    - arm64: dts: imx8mn-var-som: add missing pull-up for onboard PHY reset pinmux
+    - word-at-a-time: use the same return type for has_zero regardless of
+      endianness
+    - KVM: s390: fix sthyi error handling
+    - wifi: cfg80211: Fix return value in scan logic
+    - net/mlx5: DR, fix memory leak in mlx5dr_cmd_create_reformat_ctx
+    - net/mlx5e: fix return value check in mlx5e_ipsec_remove_trailer()
+    - bpf: Add length check for SK_DIAG_BPF_STORAGE_REQ_MAP_FD parsing
+    - rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length
+    - net: dsa: fix value check in bcm_sf2_sw_probe()
+    - perf test uprobe_from_different_cu: Skip if there is no gcc
+    - net: sched: cls_u32: Fix match key mis-addressing
+    - mISDN: hfcpci: Fix potential deadlock on &hc->lock
+    - qed: Fix kernel-doc warnings
+    - qed: Fix scheduling in a tasklet while getting stats
+    - net: annotate data-races around sk->sk_max_pacing_rate
+    - net: add missing READ_ONCE(sk->sk_rcvlowat) annotation
+    - net: add missing READ_ONCE(sk->sk_sndbuf) annotation
+    - net: add missing READ_ONCE(sk->sk_rcvbuf) annotation
+    - net: add missing data-race annotations around sk->sk_peek_off
+    - net: add missing data-race annotation for sk_ll_usec
+    - net/sched: taprio: Limit TCA_TAPRIO_ATTR_SCHED_CYCLE_TIME to INT_MAX.
+    - bpf, cpumap: Handle skb as well when clean up ptr_ring
+    - bpf: sockmap: Remove preempt_disable in sock_map_sk_acquire
+    - net: ll_temac: Switch to use dev_err_probe() helper
+    - net: ll_temac: fix error checking of irq_of_parse_and_map()
+    - net: korina: handle clk prepare error in korina_probe()
+    - net: netsec: Ignore 'phy-mode' on SynQuacer in DT mode
+    - net: dcb: choose correct policy to parse DCB_ATTR_BCN
+    - s390/qeth: Don't call dev_close/dev_open (DOWN/UP)
+    - ip6mr: Fix skb_under_panic in ip6mr_cache_report()
+    - vxlan: Fix nexthop hash size
+    - net/mlx5: fs_core: Make find_closest_ft more generic
+    - net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio
+    - prestera: fix fallback to previous version on same major version
+    - tcp_metrics: fix addr_same() helper
+    - tcp_metrics: annotate data-races around tm->tcpm_stamp
+    - tcp_metrics: annotate data-races around tm->tcpm_lock
+    - tcp_metrics: annotate data-races around tm->tcpm_vals[]
+    - tcp_metrics: annotate data-races around tm->tcpm_net
+    - tcp_metrics: fix data-race in tcpm_suck_dst() vs fastopen
+    - scsi: zfcp: Defer fc_rport blocking until after ADISC response
+    - scsi: storvsc: Limit max_sectors for virtual Fibre Channel devices
+    - libceph: fix potential hang in ceph_osdc_notify()
+    - USB: zaurus: Add ID for A-300/B-500/C-700
+    - ceph: defer stopping mdsc delayed_work
+    - firmware: arm_scmi: Drop OF node reference in the transport channel setup
+    - exfat: use kvmalloc_array/kvfree instead of kmalloc_array/kfree
+    - exfat: release s_lock before calling dir_emit()
+    - mtd: spinand: toshiba: Fix ecc_get_status
+    - mtd: rawnand: meson: fix OOB available bytes for ECC
+    - arm64: dts: stratix10: fix incorrect I2C property for SCL signal
+    - wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
+    - rbd: prevent busy loop when requesting exclusive lock
+    - bpf: Disable preemption in bpf_event_output
+    - open: make RESOLVE_CACHED correctly test for O_TMPFILE
+    - drm/ttm: check null pointer before accessing when swapping
+    - bpf, cpumap: Make sure kthread is running before map update returns
+    - file: reinstate f_pos locking optimization for regular files
+    - fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_load_attr_list()
+    - fs/sysv: Null check to prevent null-ptr-deref bug
+    - net: usbnet: Fix WARNING in usbnet_start_xmit/usb_submit_urb
+    - fs: Protect reconfiguration of sb read-write from racing writes
+    - ext2: Drop fragment support
+    - mtd: rawnand: omap_elm: Fix incorrect type in assignment
+    - mtd: rawnand: rockchip: fix oobfree offset and description
+    - mtd: rawnand: rockchip: Align hwecc vs. raw page helper layouts
+    - mtd: rawnand: fsl_upm: Fix an off-by one test in fun_exec_op()
+    - powerpc/mm/altmap: Fix altmap boundary check
+    - drm/imx/ipuv3: Fix front porch adjustment upon hactive aligning
+    - selftests/rseq: check if libc rseq support is registered
+    - selftests/rseq: Play nice with binaries statically linked against glibc
+      2.35+
+    - soundwire: bus: pm_runtime_request_resume on peripheral attachment
+    - soundwire: fix enumeration completion
+    - PM / wakeirq: support enabling wake-up irq after runtime_suspend called
+    - PM: sleep: wakeirq: fix wake irq arming
+    - Linux 5.15.126
+  * Jammy update: v5.15.125 upstream stable release (LP: #2036843)
+    - ia64/cpu: Switch to arch_cpu_finalize_init()
+    - m68k/cpu: Switch to arch_cpu_finalize_init()
+    - mips/cpu: Switch to arch_cpu_finalize_init()
+    - sh/cpu: Switch to arch_cpu_finalize_init()
+    - Linux 5.15.125
+    - Upstream stable to v5.15.125
+  * CVE-2023-42755
+    - net/sched: Retire rsvp classifier
+    - [Config] remove NET_CLS_RSVP and NET_CLS_RSVP6
+  * CVE-2023-42753
+    - netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for
+      ip_set_hash_netportnet.c
+  * CVE-2023-34319
+    - xen/netback: Fix buffer overrun triggered by unusual packet
+  * CVE-2023-5197
+    - netfilter: nf_tables: disallow rule removal from chain binding
+  * CVE-2023-4921
+    - net: sched: sch_qfq: Fix UAF in qfq_dequeue()
+  * CVE-2023-42752
+    - igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
+  * Avoid address overwrite in kernel_connect (LP: #2035163)
+    - net: Avoid address overwrite in kernel_connect
+  * NULL Pointer Dereference During KVM MMU Page Invalidation (LP: #2035166)
+    - KVM: x86/mmu: Track the number of TDP MMU pages, but not the actual pages
+  * Fix suspend hang on Lenovo workstation (LP: #2034479)
+    - igb: Fix igb_down hung on surprise removal
+  * [regression] Unable to initialize SGX enclaves with XFRM other than 3
+    (LP: #2034745)
+    - x86/fpu: Set X86_FEATURE_OSXSAVE feature after enabling OSXSAVE in CR4
+  * CVE-2023-4881
+    - netfilter: nftables: exthdr: fix 4-byte stack OOB write
+  * CVE-2023-4622
+    - af_unix: Fix null-ptr-deref in unix_stream_sendpage().
+  * Jammy update: v5.15.124 upstream stable release (LP: #2035400)
+    - jbd2: Fix wrongly judgement for buffer head removing while doing checkpoint
+    - KVM: s390: pv: fix index value of replaced ASCE
+    - io_uring: don't audit the capability check in io_uring_create()
+    - gpio: tps68470: Make tps68470_gpio_output() always set the initial value
+    - pwm: Add a stub for devm_pwmchip_add()
+    - gpio: mvebu: Make use of devm_pwmchip_add
+    - gpio: mvebu: fix irq domain leak
+    - btrfs: fix race between quota disable and relocation
+    - i2c: Delete error messages for failed memory allocations
+    - i2c: Improve size determinations
+    - i2c: nomadik: Remove unnecessary goto label
+    - i2c: nomadik: Use devm_clk_get_enabled()
+    - i2c: nomadik: Remove a useless call in the remove function
+    - PCI/ASPM: Return 0 or -ETIMEDOUT from pcie_retrain_link()
+    - PCI/ASPM: Factor out pcie_wait_for_retrain()
+    - PCI/ASPM: Avoid link retraining race
+    - PCI: rockchip: Remove writes to unused registers
+    - PCI: rockchip: Fix window mapping and address translation for endpoint
+    - PCI: rockchip: Don't advertise MSI-X in PCIe capabilities
+    - dlm: cleanup plock_op vs plock_xop
+    - dlm: rearrange async condition return
+    - fs: dlm: interrupt posix locks only when process is killed
+    - drm/ttm: Don't print error message if eviction was interrupted
+    - drm/ttm: Don't leak a resource on eviction error
+    - n_tty: Rename tail to old_tail in n_tty_read()
+    - tty: fix hang on tty device with no_room set
+    - drm/ttm: never consider pinned BOs for eviction&swap
+    - cifs: missing directory in MAINTAINERS file
+    - cifs: use fs_context for automounts
+    - ksmbd: remove internal.h include
+    - cifs: if deferred close is disabled then close files immediately
+    - pwm: meson: Simplify duplicated per-channel tracking
+    - pwm: meson: fix handling of period/duty if greater than UINT_MAX
+    - tracing/probes: Add symstr type for dynamic events
+    - tracing/probes: Fix to avoid double count of the string length on the array
+    - tracing: Allow synthetic events to pass around stacktraces
+    - Revert "tracing: Add "(fault)" name injection to kernel probes"
+    - tracing/probes: Fix to record 0-length data_loc in fetch_store_string*() if
+      fails
+    - scsi: qla2xxx: Remove unused declarations for qla2xxx
+    - scsi: qla2xxx: Multi-que support for TMF
+    - scsi: qla2xxx: Fix task management cmd failure
+    - scsi: qla2xxx: Fix task management cmd fail due to unavailable resource
+    - scsi: qla2xxx: Add debug prints in the device remove path
+    - scsi: qla2xxx: Fix hang in task management
+    - drm/amdgpu: fix vkms crtc settings
+    - drm/amdgpu/vkms: relax timer deactivation by hrtimer_try_to_cancel
+    - phy: qcom-snps: Use dev_err_probe() to simplify code
+    - phy: qcom-snps: correct struct qcom_snps_hsphy kerneldoc
+    - phy: qcom-snps-femto-v2: keep cfg_ahb_clk enabled during runtime suspend
+    - phy: qcom-snps-femto-v2: properly enable ref clock
+    - soundwire: qcom: update status correctly with mask
+    - media: staging: atomisp: select V4L2_FWNODE
+    - i40e: Fix an NULL vs IS_ERR() bug for debugfs_create_dir()
+    - iavf: fix potential deadlock on allocation failure
+    - iavf: check for removal state before IAVF_FLAG_PF_COMMS_FAILED
+    - net: phy: marvell10g: fix 88x3310 power up
+    - net: hns3: fix wrong tc bandwidth weight data issue
+    - net: hns3: fix wrong bw weight of disabled tc issue
+    - vxlan: move to its own directory
+    - vxlan: calculate correct header length for GPE
+    - phy: hisilicon: Fix an out of bounds check in hisi_inno_phy_probe()
+    - ethernet: atheros: fix return value check in atl1e_tso_csum()
+    - ipv6 addrconf: fix bug where deleting a mngtmpaddr can create a new
+      temporary address
+    - ice: Fix memory management in ice_ethtool_fdir.c
+    - bonding: reset bond's flags when down link is P2P device
+    - team: reset team's flags when down link is P2P device
+    - net: stmmac: Apply redundant write work around on 4.xx too
+    - platform/x86: msi-laptop: Fix rfkill out-of-sync on MSI Wind U100
+    - igc: Fix Kernel Panic during ndo_tx_timeout callback
+    - netfilter: nft_set_rbtree: fix overlap expiration walk
+    - net/sched: mqprio: refactor nlattr parsing to a separate function
+    - net/sched: mqprio: add extack to mqprio_parse_nlattr()
+    - net/sched: mqprio: Add length check for TCA_MQPRIO_{MAX/MIN}_RATE64
+    - benet: fix return value check in be_lancer_xmit_workarounds()
+    - tipc: check return value of pskb_trim()
+    - tipc: stop tipc crypto on failure in tipc_node_create
+    - RDMA/mlx4: Make check for invalid flags stricter
+    - drm/msm/dpu: drop enum dpu_core_perf_data_bus_id
+    - drm/msm/adreno: Fix snapshot BINDLESS_DATA size
+    - RDMA/irdma: Add missing read barriers
+    - RDMA/irdma: Fix data race on CQP completion stats
+    - RDMA/irdma: Fix data race on CQP request done
+    - RDMA/mthca: Fix crash when polling CQ for shared QPs
+    - RDMA/bnxt_re: Prevent handling any completions after qp destroy
+    - drm/msm: Fix IS_ERR_OR_NULL() vs NULL check in a5xx_submit_in_rb()
+    - ASoC: fsl_spdif: Silence output on stop
+    - block: Fix a source code comment in include/uapi/linux/blkzoned.h
+    - dm raid: fix missing reconfig_mutex unlock in raid_ctr() error paths
+    - dm raid: clean up four equivalent goto tags in raid_ctr()
+    - dm raid: protect md_stop() with 'reconfig_mutex'
+    - drm/amd: Fix an error handling mistake in psp_sw_init()
+    - RDMA/irdma: Report correct WC error
+    - ata: pata_ns87415: mark ns87560_tf_read static
+    - ring-buffer: Fix wrong stat of cpu_buffer->read
+    - tracing: Fix warning in trace_buffered_event_disable()
+    - Revert "usb: gadget: tegra-xudc: Fix error check in
+      tegra_xudc_powerdomain_init()"
+    - usb: gadget: call usb_gadget_check_config() to verify UDC capability
+    - USB: gadget: Fix the memory leak in raw_gadget driver
+    - KVM: Grab a reference to KVM for VM and vCPU stats file descriptors
+    - KVM: VMX: Don't fudge CR0 and CR4 for restricted L2 guest
+    - serial: qcom-geni: drop bogus runtime pm state update
+    - serial: 8250_dw: Preserve original value of DLF register
+    - serial: sifive: Fix sifive_serial_console_setup() section
+    - USB: serial: option: support Quectel EM060K_128
+    - USB: serial: option: add Quectel EC200A module support
+    - USB: serial: simple: add Kaufmann RKS+CAN VCP
+    - USB: serial: simple: sort driver entries
+    - can: gs_usb: gs_can_close(): add missing set of CAN state to
+      CAN_STATE_STOPPED
+    - Revert "usb: dwc3: core: Enable AutoRetry feature in the controller"
+    - usb: dwc3: pci: skip BYT GPIO lookup table for hardwired phy
+    - usb: dwc3: don't reset device side if dwc3 was configured as host-only
+    - usb: ohci-at91: Fix the unhandle interrupt when resume
+    - USB: quirks: add quirk for Focusrite Scarlett
+    - usb: cdns3: fix incorrect calculation of ep_buf_size when more than one
+      config
+    - usb: xhci-mtk: set the dma max_seg_size
+    - Revert "usb: xhci: tegra: Fix error check"
+    - Documentation: security-bugs.rst: update preferences when dealing with the
+      linux-distros group
+    - Documentation: security-bugs.rst: clarify CVE handling
+    - staging: r8712: Fix memory leak in _r8712_init_xmit_priv()
+    - staging: ks7010: potential buffer overflow in ks_wlan_set_encode_ext()
+    - tty: n_gsm: fix UAF in gsm_cleanup_mux
+    - Revert "xhci: add quirk for host controllers that don't update endpoint DCS"
+    - ALSA: hda/relatek: Enable Mute LED on HP 250 G8
+    - hwmon: (k10temp) Enable AMD3255 Proc to show negative temperature
+    - hwmon: (nct7802) Fix for temp6 (PECI1) processed even if PECI1 disabled
+    - btrfs: check if the transaction was aborted at btrfs_wait_for_commit()
+    - btrfs: check for commit error at btrfs_attach_transaction_barrier()
+    - file: always lock position for FMODE_ATOMIC_POS
+    - nfsd: Remove incorrect check in nfsd4_validate_stateid
+    - tpm_tis: Explicitly check for error code
+    - irq-bcm6345-l1: Do not assume a fixed block to cpu mapping
+    - irqchip/gic-v4.1: Properly lock VPEs when doing a directLPI invalidation
+    - locking/rtmutex: Fix task->pi_waiters integrity
+    - KVM: x86: Disallow KVM_SET_SREGS{2} if incoming CR0 is invalid
+    - virtio-net: fix race between set queues and probe
+    - s390/dasd: fix hanging device after quiesce/resume
+    - ASoC: wm8904: Fill the cache for WM8904_ADC_TEST_0 register
+    - ceph: never send metrics if disable_send_metrics is set
+    - dm cache policy smq: ensure IO doesn't prevent cleaner policy progress
+    - rbd: make get_lock_owner_info() return a single locker or NULL
+    - rbd: harden get_lock_owner_info() a bit
+    - rbd: retrieve and check lock owner twice before blocklisting
+    - tracing: Fix trace_event_raw_event_synth() if else statement
+    - ACPI: processor: perflib: Use the "no limit" frequency QoS
+    - ACPI: processor: perflib: Avoid updating frequency QoS unnecessarily
+    - cpufreq: intel_pstate: Drop ACPI _PSS states table patching
+    - selftests: mptcp: sockopt: use 'iptables-legacy' if available
+    - io_uring: treat -EAGAIN for REQ_F_NOWAIT as final for io-wq
+    - ASoC: cs42l51: fix driver to properly autoload with automatic module loading
+    - selftests: mptcp: join: only check for ip6tables if needed
+    - Linux 5.15.124
+  * Jammy update: v5.15.123 upstream stable release (LP: #2034612)
+    - ALSA: hda/realtek - remove 3k pull low procedure
+    - ALSA: hda/realtek: Add quirk for Clevo NS70AU
+    - ALSA: hda/realtek: Enable Mute LED on HP Laptop 15s-eq2xxx
+    - keys: Fix linking a duplicate key to a keyring's assoc_array
+    - perf probe: Add test for regression introduced by switch to
+      die_get_decl_file()
+    - btrfs: fix warning when putting transaction with qgroups enabled after abort
+    - fuse: revalidate: don't invalidate if interrupted
+    - btrfs: zoned: fix memory leak after finding block group with super blocks
+    - fuse: ioctl: translate ENOSYS in outarg
+    - selftests: tc: set timeout to 15 minutes
+    - selftests: tc: add 'ct' action kconfig dep
+    - regmap: Drop initial version of maximum transfer length fixes
+    - regmap: Account for register length in SMBus I/O limits
+    - can: bcm: Fix UAF in bcm_proc_show()
+    - selftests: tc: add ConnTrack procfs kconfig
+    - drm/client: Fix memory leak in drm_client_target_cloned
+    - drm/client: Fix memory leak in drm_client_modeset_probe
+    - drm/amd/display: Disable MPC split by default on special asic
+    - drm/amd/display: Keep PHY active for DP displays on DCN31
+    - ASoC: fsl_sai: Disable bit clock with transmitter
+    - ASoC: codecs: wcd938x: fix missing clsh ctrl error handling
+    - ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix missing mbhc init error handling
+    - ASoC: codecs: wcd934x: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix codec initialisation race
+    - ASoC: codecs: wcd938x: fix soundwire initialisation race
+    - ext4: correct inline offset when handling xattrs in inode body
+    - drm/radeon: Fix integer overflow in radeon_cs_parser_init
+    - ALSA: emu10k1: roll up loops in DSP setup code for Audigy
+    - quota: Properly disable quotas when add_dquot_ref() fails
+    - quota: fix warning in dqgrab()
+    - udf: Fix uninitialized array access for some pathnames
+    - fs: jfs: Fix UBSAN: array-index-out-of-bounds in dbAllocDmapLev
+    - MIPS: dec: prom: Address -Warray-bounds warning
+    - FS: JFS: Fix null-ptr-deref Read in txBegin
+    - FS: JFS: Check for read-only mounted filesystem in txBegin
+    - spi: bcm63xx: fix max prepend length
+    - fbdev: imxfb: warn about invalid left/right margin
+    - perf build: Fix library not found error when using CSLIBS
+    - pinctrl: amd: Use amd_pinconf_set() for all config options
+    - net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()
+    - bridge: Add extack warning when enabling STP in netns.
+    - ethernet: use eth_hw_addr_set() instead of ether_addr_copy()
+    - of: net: add a helper for loading netdev->dev_addr
+    - ethernet: use of_get_ethdev_address()
+    - net: ethernet: mtk_eth_soc: handle probe deferral
+    - net: sched: cls_bpf: Undo tcf_bind_filter in case of an error
+    - iavf: Fix use-after-free in free_netdev
+    - iavf: Fix out-of-bounds when setting channels on remove
+    - security: keys: Modify mismatched function name
+    - octeontx2-pf: Dont allocate BPIDs for LBK interfaces
+    - bpf: Fix subprog idx logic in check_max_stack_depth
+    - igc: Prevent garbled TX queue with XDP ZEROCOPY
+    - tcp: annotate data-races around tcp_rsk(req)->ts_recent
+    - net: ipv4: Use kfree_sensitive instead of kfree
+    - net:ipv6: check return value of pskb_trim()
+    - Revert "tcp: avoid the lookup process failing to get sk in ehash table"
+    - fbdev: au1200fb: Fix missing IRQ check in au1200fb_drv_probe
+    - llc: Don't drop packet from non-root netns.
+    - netfilter: nf_tables: fix spurious set element insertion failure
+    - netfilter: nf_tables: skip bound chain in netns release path
+    - tcp: annotate data-races around tp->tcp_tx_delay
+    - tcp: annotate data-races around tp->keepalive_time
+    - tcp: annotate data-races around tp->keepalive_intvl
+    - tcp: annotate data-races around tp->keepalive_probes
+    - tcp: annotate data-races around icsk->icsk_syn_retries
+    - tcp: annotate data-races around tp->linger2
+    - tcp: annotate data-races around rskq_defer_accept
+    - tcp: annotate data-races around tp->notsent_lowat
+    - tcp: annotate data-races around icsk->icsk_user_timeout
+    - tcp: annotate data-races around fastopenq.max_qlen
+    - net: phy: prevent stale pointer dereference in phy_init()
+    - jbd2: recheck chechpointing non-dirty buffer
+    - tracing/histograms: Return an error if we fail to add histogram to hist_vars
+      list
+    - nixge: fix mac address error handling again
+    - Linux 5.15.123
+  * allow io_uring to be disabled in runtime (LP: #2035116)
+    - io_uring: add a sysctl to disable io_uring system-wide
+  * CVE-2023-31083
+    - Bluetooth: hci_ldisc: check HCI_UART_PROTO_READY flag in HCIUARTGETPROTO
+  * CVE-2023-3772
+    - xfrm: add NULL check in xfrm_update_ae_params
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  [ Ubuntu: 5.15.0-86.96 ]
+
+  * jammy/linux: 5.15.0-86.96 -proposed tracker (LP: #2036575)
+  * 5.15.0-85 live migration regression (LP: #2036675)
+    - Revert "KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES"
+    - Revert "x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0"
+  * Regression for ubuntu_bpf test build on Jammy 5.15.0-85.95 (LP: #2035181)
+    - selftests/bpf: fix static assert compilation issue for test_cls_*.c
+  * `refcount_t: underflow; use-after-free.` on hidon w/ 5.15.0-85-generic
+    (LP: #2034447)
+    - crypto: rsa-pkcs1pad - Use helper to set reqsize
+
+  [ Ubuntu: 5.15.0-85.95 ]
+
+  * jammy/linux: 5.15.0-85.95 -proposed tracker (LP: #2033821)
+  * Please enable Renesas RZ platform serial installer (LP: #2022361)
+    - [Config] enable hihope RZ/G2M serial console
+    - [Config] Mark sh-sci as built-in
+  * Request backport of xen timekeeping performance improvements (LP: #2033122)
+    - x86/xen/time: prefer tsc as clocksource when it is invariant
+  * kdump doesn't work with UEFI secure boot and kernel lockdown enabled on
+    ARM64 (LP: #2033007)
+    - [Config]: Enable CONFIG_KEXEC_IMAGE_VERIFY_SIG
+    - kexec, KEYS: make the code in bzImage64_verify_sig generic
+    - arm64: kexec_file: use more system keyrings to verify kernel image signature
+  * ubuntu_kernel_selftests:net:vrf-xfrm-tests.sh: 8 failed test cases on
+    jammy/fips (LP: #2019880)
+    - selftests: net: vrf-xfrm-tests: change authentication and encryption algos
+  * ubuntu_kernel_selftests:net:tls: 88 failed test cases on jammy/fips
+    (LP: #2019868)
+    - selftests/harness: allow tests to be skipped during setup
+    - selftests: net: tls: check if FIPS mode is enabled
+  * A general-proteciton exception during guest migration to unsupported PKRU
+    machine (LP: 2032164, reverted)
+    - x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0
+    - KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES
+  * CVE-2023-4569
+    - netfilter: nf_tables: deactivate catchall elements in next generation
+  * CVE-2023-20569
+    - x86/cpu, kvm: Add support for CPUID_80000021_EAX
+    - x86/srso: Add a Speculative RAS Overflow mitigation
+    - x86/srso: Add IBPB_BRTYPE support
+    - x86/srso: Add SRSO_NO support
+    - x86/srso: Add IBPB
+    - x86/srso: Add IBPB on VMEXIT
+    - x86/srso: Fix return thunks in generated code
+    - x86/srso: Tie SBPB bit setting to microcode patch detection
+    - x86: fix backwards merge of GDS/SRSO bit
+    - x86/srso: Fix build breakage with the LLVM linker
+    - x86/cpu: Fix __x86_return_thunk symbol type
+    - x86/cpu: Fix up srso_safe_ret() and __x86_return_thunk()
+    - x86/alternative: Make custom return thunk unconditional
+    - objtool: Add frame-pointer-specific function ignore
+    - x86/ibt: Add ANNOTATE_NOENDBR
+    - x86/cpu: Clean up SRSO return thunk mess
+    - x86/cpu: Rename original retbleed methods
+    - x86/cpu: Rename srso_(.*)_alias to srso_alias_\1
+    - x86/cpu: Cleanup the untrain mess
+    - x86/srso: Explain the untraining sequences a bit more
+    - x86/static_call: Fix __static_call_fixup()
+    - x86/retpoline: Don't clobber RFLAGS during srso_safe_ret()
+    - x86/srso: Disable the mitigation on unaffected configurations
+    - x86/retpoline,kprobes: Fix position of thunk sections with CONFIG_LTO_CLANG
+    - objtool/x86: Fixup frame-pointer vs rethunk
+    - x86/srso: Correct the mitigation status when SMT is disabled
+    - objtool/x86: Fix SRSO mess
+    - Ubuntu: [Config]: enable Speculative Return Stack Overflow mitigation
+  * Fix unreliable ethernet cable detection on I219 NIC (LP: #2028122)
+    - e1000e: Use PME poll to circumvent unreliable ACPI wake
+  * Need to get fine-grained control for FAN(TFN) Participant. (LP: #2031333)
+    - ACPI: fan: Separate file for attributes creation
+    - ACPI: fan: Optimize struct acpi_fan_fif
+    - ACPI: fan: Properly handle fine grain control
+    - ACPI: fan: Add additional attributes for fine grain control
+  * [SRU][Ubuntu 22.04.1] Unable to interpret the frequency values in
+    cpuinfo_min_freq and cpuino_max_freq sysfs files. (LP: #2030924)
+    - cpufreq: intel_pstate: Fix scaling for hybrid-capable
+  * CVE-2023-40283
+    - Bluetooth: L2CAP: Fix use-after-free in l2cap_sock_ready_cb
+  * CVE-2023-20588
+    - x86/bugs: Increase the x86 bugs vector size to two u32s
+    - x86/CPU/AMD: Do not leak quotient data after a division by 0
+    - x86/CPU/AMD: Fix the DIV(0) initial fix attempt
+  * CVE-2023-4194
+    - net: tun_chr_open(): set sk_uid from current_fsuid()
+    - net: tap_open(): set sk_uid from current_fsuid()
+  * CVE-2023-4155
+    - KVM: SEV: Refactor out sev_es_state struct
+    - KVM: SEV: Fall back to vmalloc for SEV-ES scratch area if necessary
+    - KVM: SVM: Do not terminate SEV-ES guests on GHCB validation failure
+    - KVM: SVM: Exit to userspace on ENOMEM/EFAULT GHCB errors
+    - KVM: SEV: snapshot the GHCB before accessing it
+    - KVM: SEV: only access GHCB fields once
+  * CVE-2023-1206
+    - tcp: Reduce chance of collisions in inet6_hashfn().
+  * Crashing with CPU soft lock on GA kernel 5.15.0.79.76 and HWE kernel
+    5.19.0-46.47-22.04.1 (LP: #2032176)
+    - Revert "KVM: x86: enable TDP MMU by default"
+  * Jammy update: v5.15.122 upstream stable release (LP: #2032690)
+    - Linux 5.15.122
+    - Upstream stable to v5.15.122
+  * Jammy update: v5.15.121 upstream stable release (LP: #2032689)
+    - netfilter: nf_tables: drop map element references from preparation phase
+    - fs: pipe: reveal missing function protoypes
+    - x86/resctrl: Only show tasks' pid in current pid namespace
+    - blk-iocost: use spin_lock_irqsave in adjust_inuse_and_calc_cost
+    - md/raid10: check slab-out-of-bounds in md_bitmap_get_counter
+    - md/raid10: fix overflow of md/safe_mode_delay
+    - md/raid10: fix wrong setting of max_corr_read_errors
+    - md/raid10: fix null-ptr-deref of mreplace in raid10_sync_request
+    - md/raid10: fix io loss while replacement replace rdev
+    - irqchip/jcore-aic: Fix missing allocation of IRQ descriptors
+    - svcrdma: Prevent page release when nothing was received
+    - posix-timers: Prevent RT livelock in itimer_delete()
+    - tracing/timer: Add missing hrtimer modes to decode_hrtimer_mode().
+    - clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe
+    - PM: domains: fix integer overflow issues in genpd_parse_state()
+    - perf/arm-cmn: Fix DTC reset
+    - powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
+    - ARM: 9303/1: kprobes: avoid missing-declaration warnings
+    - cpufreq: intel_pstate: Fix energy_performance_preference for passive
+    - thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()
+    - rcutorture: Correct name of use_softirq module parameter
+    - rcuscale: Always log error message
+    - rcuscale: Move shutdown from wait_event() to wait_event_idle()
+    - rcu/rcuscale: Move rcu_scale_*() after kfree_scale_cleanup()
+    - rcu/rcuscale: Stop kfree_scale_thread thread(s) after unloading rcuscale
+    - kselftest: vDSO: Fix accumulation of uninitialized ret when CLOCK_REALTIME
+      is undefined
+    - perf/ibs: Fix interface via core pmu events
+    - x86/mm: Fix __swp_entry_to_pte() for Xen PV guests
+    - locking/atomic: arm: fix sync ops
+    - evm: Complete description of evm_inode_setattr()
+    - evm: Fix build warnings
+    - ima: Fix build warnings
+    - pstore/ram: Add check for kstrdup
+    - igc: Enable and fix RX hash usage by netstack
+    - wifi: ath9k: fix AR9003 mac hardware hang check register offset calculation
+    - wifi: ath9k: avoid referencing uninit memory in ath9k_wmi_ctrl_rx
+    - libbpf: btf_dump_type_data_check_overflow needs to consider
+      BTF_MEMBER_BITFIELD_SIZE
+    - samples/bpf: Fix buffer overflow in tcp_basertt
+    - spi: spi-geni-qcom: Correct CS_TOGGLE bit in SPI_TRANS_CFG
+    - wifi: wilc1000: fix for absent RSN capabilities WFA testcase
+    - wifi: mwifiex: Fix the size of a memory allocation in
+      mwifiex_ret_802_11_scan()
+    - sctp: add bpf_bypass_getsockopt proto callback
+    - libbpf: fix offsetof() and container_of() to work with CO-RE
+    - bpf: Don't EFAULT for {g,s}setsockopt with wrong optlen
+    - spi: dw: Round of n_bytes to power of 2
+    - nfc: llcp: fix possible use of uninitialized variable in
+      nfc_llcp_send_connect()
+    - bpftool: JIT limited misreported as negative value on aarch64
+    - regulator: core: Fix more error checking for debugfs_create_dir()
+    - regulator: core: Streamline debugfs operations
+    - wifi: orinoco: Fix an error handling path in spectrum_cs_probe()
+    - wifi: orinoco: Fix an error handling path in orinoco_cs_probe()
+    - wifi: atmel: Fix an error handling path in atmel_probe()
+    - wl3501_cs: use eth_hw_addr_set()
+    - wifi: wl3501_cs: Fix an error handling path in wl3501_probe()
+    - wifi: ray_cs: Utilize strnlen() in parse_addr()
+    - wifi: ray_cs: Drop useless status variable in parse_addr()
+    - wifi: ray_cs: Fix an error handling path in ray_probe()
+    - wifi: ath9k: don't allow to overwrite ENDPOINT0 attributes
+    - selftests/bpf: Fix check_mtu using wrong variable type
+    - wifi: rsi: Do not configure WoWlan in shutdown hook if not enabled
+    - wifi: rsi: Do not set MMC_PM_KEEP_POWER in shutdown
+    - watchdog/perf: define dummy watchdog_update_hrtimer_threshold() on correct
+      config
+    - watchdog/perf: more properly prevent false positives with turbo modes
+    - kexec: fix a memory leak in crash_shrink_memory()
+    - memstick r592: make memstick_debug_get_tpc_name() static
+    - wifi: ath9k: Fix possible stall on ath9k_txq_list_has_key()
+    - rtnetlink: extend RTEXT_FILTER_SKIP_STATS to IFLA_VF_INFO
+    - wifi: iwlwifi: pull from TXQs with softirqs disabled
+    - iwlwifi: don't dump_stack() when we get an unexpected interrupt
+    - wifi: iwlwifi: pcie: fix NULL pointer dereference in
+      iwl_pcie_irq_rx_msix_handler()
+    - wifi: cfg80211: rewrite merging of inherited elements
+    - wifi: iwlwifi: mvm: indicate HW decrypt for beacon protection
+    - wifi: ath9k: convert msecs to jiffies where needed
+    - bpf: Omit superfluous address family check in __bpf_skc_lookup
+    - bpf: Factor out socket lookup functions for the TC hookpoint.
+    - bpf: Call __bpf_sk_lookup()/__bpf_skc_lookup() directly via TC hookpoint
+    - bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings
+    - can: length: fix bitstuffing count
+    - igc: Fix race condition in PTP tx code
+    - net: stmmac: fix double serdes powerdown
+    - netlink: fix potential deadlock in netlink_set_err()
+    - netlink: do not hard code device address lenth in fdb dumps
+    - bonding: do not assume skb mac_header is set
+    - selftests: rtnetlink: remove netdevsim device after ipsec offload test
+    - gtp: Fix use-after-free in __gtp_encap_destroy().
+    - net: axienet: Move reset before 64-bit DMA detection
+    - sfc: fix crash when reading stats while NIC is resetting
+    - lib/ts_bm: reset initial match offset for every block of text
+    - netfilter: conntrack: dccp: copy entire header to stack buffer, not just
+      basic one
+    - netfilter: nf_conntrack_sip: fix the ct_sip_parse_numerical_param() return
+      value.
+    - ipvlan: Fix return value of ipvlan_queue_xmit()
+    - netlink: Add __sock_i_ino() for __netlink_diag_dump().
+    - drm/amd/display: Add logging for display MALL refresh setting
+    - radeon: avoid double free in ci_dpm_init()
+    - drm/amd/display: Explicitly specify update type per plane info change
+    - Input: drv260x - sleep between polling GO bit
+    - drm/bridge: tc358768: always enable HS video mode
+    - drm/bridge: tc358768: fix PLL parameters computation
+    - drm/bridge: tc358768: fix PLL target frequency
+    - drm/bridge: tc358768: fix TCLK_ZEROCNT computation
+    - drm/bridge: tc358768: Add atomic_get_input_bus_fmts() implementation
+    - drm/bridge: tc358768: fix TCLK_TRAILCNT computation
+    - drm/bridge: tc358768: fix THS_ZEROCNT computation
+    - drm/bridge: tc358768: fix TXTAGOCNT computation
+    - drm/bridge: tc358768: fix THS_TRAILCNT computation
+    - drm/vram-helper: fix function names in vram helper doc
+    - ARM: dts: BCM5301X: Drop "clock-names" from the SPI node
+    - ARM: dts: meson8b: correct uart_B and uart_C clock references
+    - Input: adxl34x - do not hardcode interrupt trigger type
+    - drm: sun4i_tcon: use devm_clk_get_enabled in `sun4i_tcon_init_clocks`
+    - drm/panel: sharp-ls043t1le01: adjust mode settings
+    - ARM: dts: stm32: Move ethernet MAC EEPROM from SoM to carrier boards
+    - bus: ti-sysc: Fix dispc quirk masking bool variables
+    - arm64: dts: microchip: sparx5: do not use PSCI on reference boards
+    - clk: imx: scu: use _safe list iterator to avoid a use after free
+    - RDMA/bnxt_re: Disable/kill tasklet only if it is enabled
+    - RDMA/bnxt_re: Fix to remove unnecessary return labels
+    - RDMA/bnxt_re: Use unique names while registering interrupts
+    - RDMA/bnxt_re: Remove a redundant check inside bnxt_re_update_gid
+    - RDMA/bnxt_re: Fix to remove an unnecessary log
+    - drm/msm/dsi: don't allow enabling 14nm VCO with unprogrammed rate
+    - drm/msm/disp/dpu: get timing engine status from intf status register
+    - drm/msm/dpu: Set DPU_DATA_HCTL_EN for in INTF_SC7180_MASK
+    - ARM: dts: gta04: Move model property out of pinctrl node
+    - arm64: dts: qcom: msm8916: correct camss unit address
+    - arm64: dts: qcom: msm8994: correct SPMI unit address
+    - arm64: dts: qcom: msm8996: correct camss unit address
+    - arm64: dts: qcom: sdm630: correct camss unit address
+    - arm64: dts: qcom: sdm845: correct camss unit address
+    - arm64: dts: qcom: db820c: Move blsp1_uart2 pin states to msm8996.dtsi
+    - arm64: dts: qcom: apq8016-sbc: Update modem and WiFi firmware path
+    - arm64: dts: qcom: apq8016-sbc: Clarify firmware-names
+    - arm64: dts: qcom: apq8016-sbc: fix mpps state names
+    - arm64: dts: qcom: Drop unneeded extra device-specific includes
+    - arm64: dts: qcom: apq8016-sbc: Fix regulator constraints
+    - arm64: dts: qcom: apq8016-sbc: Fix 1.8V power rail on LS expansion
+    - drm/panel: simple: fix active size for Ampire AM-480272H3TMQW-T01H
+    - ARM: ep93xx: fix missing-prototype warnings
+    - ARM: omap2: fix missing tick_broadcast() prototype
+    - arm64: dts: qcom: apq8096: fix fixed regulator name property
+    - arm64: dts: mediatek: mt8183: Add mediatek,broken-save-restore-fw to kukui
+    - ARM: dts: stm32: Shorten the AV96 HDMI sound card name
+    - memory: brcmstb_dpfe: fix testing array offset after use
+    - ASoC: es8316: Increment max value for ALC Capture Target Volume control
+    - ASoC: es8316: Do not set rate constraints for unsupported MCLKs
+    - ARM: dts: meson8: correct uart_B and uart_C clock references
+    - soc/fsl/qe: fix usb.c build errors
+    - RDMA/irdma: avoid fortify-string warning in irdma_clr_wqes
+    - IB/hfi1: Use bitmap_zalloc() when applicable
+    - IB/hfi1: Fix wrong mmu_node used for user SDMA packet after invalidate
+    - RDMA/hns: Fix hns_roce_table_get return value
+    - ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier
+    - arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1
+    - fbdev: omapfb: lcd_mipid: Fix an error handling path in mipid_spi_probe()
+    - arm64: dts: ti: k3-j7200: Fix physical address of pin
+    - ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2
+    - ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx
+    - hwmon: (gsc-hwmon) fix fan pwm temperature scaling
+    - hwmon: (adm1275) Allow setting sample averaging
+    - hwmon: (pmbus/adm1275) Fix problems with temperature monitoring on ADM1272
+    - ARM: dts: BCM5301X: fix duplex-full => full-duplex
+    - drm/amdkfd: Fix potential deallocation of previously deallocated memory.
+    - drm/amd/display: Fix artifacting on eDP panels when engaging freesync video
+      mode
+    - drm/radeon: fix possible division-by-zero errors
+    - amdgpu: validate offset_in_bo of drm_amdgpu_gem_va
+    - drm/msm/a5xx: really check for A510 in a5xx_gpu_init
+    - RDMA/bnxt_re: wraparound mbox producer index
+    - RDMA/bnxt_re: Avoid calling wake_up threads from spin_lock context
+    - clk: imx: clk-imx8mn: fix memory leak in imx8mn_clocks_probe
+    - clk: imx: clk-imx8mp: improve error handling in imx8mp_clocks_probe()
+    - arm64: dts: qcom: sm8250-edo: Panel framebuffer is 2.5k instead of 4k
+    - clk: clocking-wizard: Fix Oops in clk_wzrd_register_divider()
+    - clk: tegra: tegra124-emc: Fix potential memory leak
+    - ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer
+    - drm/msm/dpu: do not enable color-management if DSPPs are not available
+    - drm/msm/dp: Free resources after unregistering them
+    - arm64: dts: mediatek: Add cpufreq nodes for MT8192
+    - arm64: dts: mediatek: mt8192: Fix CPUs capacity-dmips-mhz
+    - drm/msm/dpu: correct MERGE_3D length
+    - clk: vc5: check memory returned by kasprintf()
+    - clk: cdce925: check return value of kasprintf()
+    - clk: si5341: return error if one synth clock registration fails
+    - clk: si5341: check return value of {devm_}kasprintf()
+    - clk: si5341: free unused memory on probe failure
+    - clk: keystone: sci-clk: check return value of kasprintf()
+    - clk: ti: clkctrl: check return value of kasprintf()
+    - drivers: meson: secure-pwrc: always enable DMA domain
+    - ovl: update of dentry revalidate flags after copy up
+    - ASoC: imx-audmix: check return value of devm_kasprintf()
+    - clk: Fix memory leak in devm_clk_notifier_register()
+    - PCI: cadence: Fix Gen2 Link Retraining process
+    - PCI: vmd: Reset VMD config register between soft reboots
+    - scsi: qedf: Fix NULL dereference in error handling
+    - pinctrl: bcm2835: Handle gpiochip_add_pin_range() errors
+    - PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free
+    - scsi: 3w-xxxx: Add error handling for initialization failure in tw_probe()
+    - PCI: pciehp: Cancel bringup sequence if card is not present
+    - PCI: ftpci100: Release the clock resources
+    - PCI: Add pci_clear_master() stub for non-CONFIG_PCI
+    - perf bench: Use unbuffered output when pipe/tee'ing to a file
+    - perf bench: Add missing setlocale() call to allow usage of %'d style
+      formatting
+    - pinctrl: cherryview: Return correct value if pin in push-pull mode
+    - kcsan: Don't expect 64 bits atomic builtins from 32 bits architectures
+    - powerpc/interrupt: Don't read MSR from interrupt_exit_kernel_prepare()
+    - powerpc/signal32: Force inlining of __unsafe_save_user_regs() and
+      save_tm_user_regs_unsafe()
+    - perf script: Fix allocation of evsel->priv related to per-event dump files
+    - perf dwarf-aux: Fix off-by-one in die_get_varname()
+    - powerpc/64s: Fix VAS mm use after free
+    - pinctrl: microchip-sgpio: check return value of devm_kasprintf()
+    - pinctrl: at91-pio4: check return value of devm_kasprintf()
+    - powerpc/powernv/sriov: perform null check on iov before dereferencing iov
+    - powerpc: simplify ppc_save_regs
+    - powerpc: update ppc_save_regs to save current r1 in pt_regs
+    - riscv: uprobes: Restore thread.bad_cause
+    - powerpc/book3s64/mm: Fix DirectMap stats in /proc/meminfo
+    - powerpc/mm/dax: Fix the condition when checking if altmap vmemap can cross-
+      boundary
+    - hwrng: virtio - add an internal buffer
+    - hwrng: virtio - don't wait on cleanup
+    - hwrng: virtio - don't waste entropy
+    - hwrng: virtio - always add a pending request
+    - hwrng: virtio - Fix race on data_avail and actual data
+    - modpost: remove broken calculation of exception_table_entry size
+    - crypto: nx - fix build warnings when DEBUG_FS is not enabled
+    - modpost: fix section mismatch message for R_ARM_ABS32
+    - modpost: fix section mismatch message for R_ARM_{PC24,CALL,JUMP24}
+    - crypto: marvell/cesa - Fix type mismatch warning
+    - modpost: fix off by one in is_executable_section()
+    - ARC: define ASM_NL and __ALIGN(_STR) outside #ifdef __ASSEMBLY__ guard
+    - crypto: qat - honor CRYPTO_TFM_REQ_MAY_SLEEP flag
+    - crypto: qat - replace get_current_node() with numa_node_id()
+    - crypto: qat - use reference to structure in dma_map_single()
+    - crypto: kpp - Add helper to set reqsize
+    - crypto: qat - Use helper to set reqsize
+    - crypto: qat - unmap buffer before free for DH
+    - crypto: qat - unmap buffers before free for RSA
+    - NFSv4.1: freeze the session table upon receiving NFS4ERR_BADSESSION
+    - SMB3: Do not send lease break acknowledgment if all file handles have been
+      closed
+    - dax: Fix dax_mapping_release() use after free
+    - dax: Introduce alloc_dev_dax_id()
+    - dax/kmem: Pass valid argument to memory_group_register_static
+    - hwrng: st - keep clock enabled while hwrng is registered
+    - kbuild: Disable GCOV for *.mod.o
+    - efi/libstub: Disable PCI DMA before grabbing the EFI memory map
+    - ksmbd: avoid field overflow warning
+    - ACPI: utils: Fix acpi_evaluate_dsm_typed() redefinition error
+    - bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
+    - USB: serial: option: add LARA-R6 01B PIDs
+    - usb: dwc3: gadget: Propagate core init errors to UDC during pullup
+    - phy: tegra: xusb: Clear the driver reference in usb-phy dev
+    - iio: adc: ad7192: Fix null ad7192_state pointer access
+    - iio: adc: ad7192: Fix internal/external clock selection
+    - iio: accel: fxls8962af: errata bug only applicable for FXLS8962AF
+    - iio: accel: fxls8962af: fixup buffer scan element type
+    - ALSA: hda/realtek: Add quirk for Clevo NPx0SNx
+    - ALSA: jack: Fix mutex call in snd_jack_report()
+    - block: fix signed int overflow in Amiga partition support
+    - block: add overflow checks for Amiga partition support
+    - block: change all __u32 annotations to __be32 in affs_hardblocks.h
+    - block: increment diskseq on all media change events
+    - SUNRPC: Fix UAF in svc_tcp_listen_data_ready()
+    - w1: w1_therm: fix locking behavior in convert_t
+    - w1: fix loop in w1_fini()
+    - sh: j2: Use ioremap() to translate device tree address into kernel memory
+    - usb: dwc2: platform: Improve error reporting for problems during .remove()
+    - usb: dwc2: Fix some error handling paths
+    - serial: 8250: omap: Fix freeing of resources on failed register
+    - clk: qcom: camcc-sc7180: Add parent dependency to all camera GDSCs
+    - clk: qcom: gcc-ipq6018: Use floor ops for sdcc clocks
+    - media: usb: Check az6007_read() return value
+    - media: videodev2.h: Fix struct v4l2_input tuner index comment
+    - media: usb: siano: Fix warning due to null work_func_t function pointer
+    - media: i2c: Correct format propagation for st-mipid02
+    - clk: qcom: reset: Allow specifying custom reset delay
+    - clk: qcom: reset: support resetting multiple bits
+    - clk: qcom: ipq6018: fix networking resets
+    - usb: dwc3: qcom: Fix potential memory leak
+    - usb: gadget: u_serial: Add null pointer check in gserial_suspend
+    - extcon: Fix kernel doc of property fields to avoid warnings
+    - extcon: Fix kernel doc of property capability fields to avoid warnings
+    - usb: phy: phy-tahvo: fix memory leak in tahvo_usb_probe()
+    - usb: hide unused usbfs_notify_suspend/resume functions
+    - serial: 8250: lock port for stop_rx() in omap8250_irq()
+    - serial: 8250: lock port for UART_IER access in omap8250_irq()
+    - kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
+    - coresight: Fix loss of connection info when a module is unloaded
+    - mfd: rt5033: Drop rt5033-battery sub-device
+    - media: venus: helpers: Fix ALIGN() of non power of two
+    - media: atomisp: gmin_platform: fix out_len in gmin_get_config_dsm_var()
+    - KVM: s390: fix KVM_S390_GET_CMMA_BITS for GFNs in memslot holes
+    - usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()
+    - usb: dwc3: qcom: Fix an error handling path in dwc3_qcom_probe()
+    - usb: common: usb-conn-gpio: Set last role to unknown before initial
+      detection
+    - usb: dwc3-meson-g12a: Fix an error handling path in dwc3_meson_g12a_probe()
+    - mfd: intel-lpss: Add missing check for platform_get_resource
+    - Revert "usb: common: usb-conn-gpio: Set last role to unknown before initial
+      detection"
+    - serial: 8250_omap: Use force_suspend and resume for system suspend
+    - test_firmware: return ENOMEM instead of ENOSPC on failed memory allocation
+    - nvmem: rmem: Use NVMEM_DEVID_AUTO
+    - mfd: stmfx: Fix error path in stmfx_chip_init
+    - mfd: stmfx: Nullify stmfx->vdd in case of error
+    - KVM: s390: vsie: fix the length of APCB bitmap
+    - KVM: s390/diag: fix racy access of physical cpu number in diag 9c handler
+    - mfd: stmpe: Only disable the regulators if they are enabled
+    - phy: tegra: xusb: check return value of devm_kzalloc()
+    - pwm: imx-tpm: force 'real_period' to be zero in suspend
+    - pwm: sysfs: Do not apply state to already disabled PWMs
+    - pwm: ab8500: Fix error code in probe()
+    - pwm: mtk_disp: Fix the disable flow of disp_pwm
+    - md/raid10: fix the condition to call bio_end_io_acct()
+    - rtc: st-lpc: Release some resources in st_rtc_probe() in case of error
+    - drm/i915/psr: Use hw.adjusted mode when calculating io/fast wake times
+    - media: cec: i2c: ch7322: also select REGMAP
+    - sctp: fix potential deadlock on &net->sctp.addr_wq_lock
+    - net/sched: act_ipt: add sanity checks on table name and hook locations
+    - Add MODULE_FIRMWARE() for FIRMWARE_TG357766.
+    - ibmvnic: Do not reset dql stats on NON_FATAL err
+    - net: dsa: vsc73xx: fix MTU configuration
+    - spi: bcm-qspi: return error if neither hif_mspi nor mspi is available
+    - mailbox: ti-msgmgr: Fill non-message tx data fields with 0x0
+    - f2fs: fix error path handling in truncate_dnode()
+    - octeontx2-af: Fix mapping for NIX block from CGX connection
+    - octeontx2-af: Add validation before accessing cgx and lmac
+    - ntfs: Fix panic about slab-out-of-bounds caused by ntfs_listxattr()
+    - powerpc: allow PPC_EARLY_DEBUG_CPM only when SERIAL_CPM=y
+    - net: bridge: keep ports without IFF_UNICAST_FLT in BR_PROMISC mode
+    - tcp: annotate data races in __tcp_oow_rate_limited()
+    - xsk: Honor SO_BINDTODEVICE on bind
+    - net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
+    - riscv: move memblock_allow_resize() after linear mapping is ready
+    - pptp: Fix fib lookup calls.
+    - net: dsa: tag_sja1105: fix MAC DA patching from meta frames
+    - octeontx-af: fix hardware timestamp configuration
+    - s390/qeth: Fix vipa deletion
+    - sh: dma: Fix DMA channel offset calculation
+    - apparmor: fix missing error check for rhashtable_insert_fast
+    - i2c: xiic: Defer xiic_wakeup() and __xiic_start_xfer() in xiic_process()
+    - i2c: xiic: Don't try to handle more interrupt events after error
+    - extcon: usbc-tusb320: Convert to i2c's .probe_new()
+    - btrfs: do not BUG_ON() on tree mod log failure at balance_level()
+    - i2c: qup: Add missing unwind goto in qup_i2c_probe()
+    - NFSD: add encoding of op_recall flag for write delegation
+    - io_uring: wait interruptibly for request completions on exit
+    - mmc: core: disable TRIM on Kingston EMMC04G-M627
+    - mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M
+    - mmc: mmci: Set PROBE_PREFER_ASYNCHRONOUS
+    - mmc: sdhci: fix DMA configure compatibility issue when 64bit DMA mode is
+      used.
+    - bcache: fixup btree_cache_wait list damage
+    - bcache: Remove unnecessary NULL point check in node allocations
+    - bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent
+    - um: Use HOST_DIR for mrproper
+    - integrity: Fix possible multiple allocation in integrity_inode_get()
+    - autofs: use flexible array in ioctl structure
+    - shmem: use ramfs_kill_sb() for kill_sb method of ramfs-based tmpfs
+    - ext4: Remove ext4 locking of moved directory
+    - Revert "f2fs: fix potential corruption when moving a directory"
+    - fs: Establish locking order for unrelated directories
+    - fs: Lock moved directories
+    - ipvs: increase ip_vs_conn_tab_bits range for 64BIT
+    - jffs2: reduce stack usage in jffs2_build_xattr_subsystem()
+    - fs: avoid empty option when generating legacy mount string
+    - btrfs: add handling for RAID1C23/DUP to btrfs_reduce_alloc_profile
+    - btrfs: delete unused BGs while reclaiming BGs
+    - btrfs: bail out reclaim process if filesystem is read-only
+    - btrfs: reinsert BGs failed to reclaim
+    - btrfs: fix race when deleting quota root from the dirty cow roots list
+    - btrfs: fix extent buffer leak after tree mod log failure at split_node()
+    - btrfs: do not BUG_ON() on tree mod log failure at __btrfs_cow_block()
+    - ASoC: mediatek: mt8173: Fix irq error path
+    - ASoC: mediatek: mt8173: Fix snd_soc_component_initialize error path
+    - ARM: dts: qcom: ipq4019: fix broken NAND controller properties override
+    - ARM: orion5x: fix d2net gpio initialization
+    - leds: trigger: netdev: Recheck NETDEV_LED_MODE_LINKUP on dev rename
+    - fs: no need to check source
+    - ovl: fix null pointer dereference in ovl_get_acl_rcu()
+    - fanotify: disallow mount/sb marks on kernel internal pseudo fs
+    - netfilter: conntrack: Avoid nf_ct_helper_hash uses after free
+    - wireguard: queueing: use saner cpu selection wrapping
+    - wireguard: netlink: send staged packets when setting initial private key
+    - tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
+    - block/partition: fix signedness issue for Amiga partitions
+    - io_uring: Use io_schedule* in cqring wait
+    - io_uring: add reschedule point to handle_tw_list()
+    - net: lan743x: Don't sleep in atomic context
+    - workqueue: clean up WORK_* constant types, clarify masking
+    - ksmbd: use ksmbd_req_buf_next() in ksmbd_smb2_check_message()
+    - ksmbd: validate command payload size
+    - ksmbd: fix out-of-bound read in smb2_write
+    - ksmbd: validate session id and tree id in the compound request
+    - drm/panel: simple: Add connector_type for innolux_at043tn24
+    - drm/bridge: ti-sn65dsi86: Fix auxiliary bus lifetime
+    - drm/panel: simple: Add Powertip PH800480T013 drm_display_mode flags
+    - igc: Remove delay during TX ring configuration
+    - net/mlx5e: fix double free in mlx5e_destroy_flow_table
+    - net/mlx5e: fix memory leak in mlx5e_ptp_open
+    - net/mlx5e: Check for NOT_READY flag state after locking
+    - igc: set TP bit in 'supported' and 'advertising' fields of
+      ethtool_link_ksettings
+    - igc: Handle PPS start time programming for past time values
+    - scsi: qla2xxx: Fix error code in qla2x00_start_sp()
+    - bpf: Fix max stack depth check for async callbacks
+    - net: mvneta: fix txq_map in case of txq_number==1
+    - gve: Set default duplex configuration to full
+    - ionic: remove WARN_ON to prevent panic_on_warn
+    - net: bgmac: postpone turning IRQs off to avoid SoC hangs
+    - net: prevent skb corruption on frag list segmentation
+    - icmp6: Fix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev().
+    - udp6: fix udp6_ehashfn() typo
+    - ntb: idt: Fix error handling in idt_pci_driver_init()
+    - NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
+    - ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
+    - NTB: ntb_transport: fix possible memory leak while device_register() fails
+    - NTB: ntb_tool: Add check for devm_kcalloc
+    - ipv6/addrconf: fix a potential refcount underflow for idev
+    - platform/x86: wmi: remove unnecessary argument
+    - platform/x86: wmi: use guid_t and guid_equal()
+    - platform/x86: wmi: move variables
+    - platform/x86: wmi: Break possible infinite loop when parsing GUID
+    - kernel/trace: Fix cleanup logic of enable_trace_eprobe
+    - igc: Fix launchtime before start of cycle
+    - igc: Fix inserting of empty frame for launchtime
+    - bpf, riscv: Support riscv jit to provide bpf_line_info
+    - riscv, bpf: Fix inconsistent JIT image generation
+    - drm/i915: Fix one wrong caching mode enum usage
+    - octeontx2-pf: Add additional check for MCAM rules
+    - erofs: avoid infinite loop in z_erofs_do_read_page() when reading beyond EOF
+    - erofs: decouple basic mount options from fs_context
+    - erofs: fix fsdax unavailability for chunk-based regular files
+    - wifi: airo: avoid uninitialized warning in airo_get_rate()
+    - bpf: cpumap: Fix memory leak in cpu_map_update_elem
+    - net/sched: flower: Ensure both minimum and maximum ports are specified
+    - riscv: mm: fix truncation warning on RV32
+    - netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()
+    - net/sched: make psched_mtu() RTNL-less safe
+    - nvme-pci: remove nvme_queue from nvme_iod
+    - nvme-pci: fix DMA direction of unmapping integrity data
+    - pinctrl: amd: Fix mistake in handling clearing pins at startup
+    - pinctrl: amd: Detect internal GPIO0 debounce handling
+    - pinctrl: amd: Detect and mask spurious interrupts
+    - pinctrl: amd: Only use special debounce behavior for GPIO 0
+    - tpm: tpm_vtpm_proxy: fix a race condition in /dev/vtpmx creation
+    - mtd: rawnand: meson: fix unaligned DMA buffers handling
+    - net: bcmgenet: Ensure MDIO unregistration has clocks enabled
+    - mm/damon/ops-common: atomically test and clear young on ptes and pmds
+    - powerpc: Fail build if using recordmcount with binutils v2.37
+    - misc: fastrpc: Create fastrpc scalar with correct buffer count
+    - powerpc/security: Fix Speculation_Store_Bypass reporting on Power10
+    - arm64: errata: Add detection for TRBE overwrite in FILL mode
+    - erofs: fix compact 4B support for 16k block size
+    - MIPS: Loongson: Fix cpu_probe_loongson() again
+    - MIPS: KVM: Fix NULL pointer dereference
+    - ext4: Fix reusing stale buffer heads from last failed mounting
+    - ext4: fix wrong unit use in ext4_mb_clear_bb
+    - ext4: get block from bh in ext4_free_blocks for fast commit replay
+    - ext4: fix wrong unit use in ext4_mb_new_blocks
+    - ext4: fix to check return value of freeze_bdev() in ext4_shutdown()
+    - ext4: turn quotas off if mount failed after enabling quotas
+    - ext4: only update i_reserved_data_blocks on successful block allocation
+    - jfs: jfs_dmap: Validate db_l2nbperpage while mounting
+    - hwrng: imx-rngc - fix the timeout for init and self check
+    - dm integrity: reduce vmalloc space footprint on 32-bit architectures
+    - PCI/PM: Avoid putting EloPOS E2/S2/H2 PCIe Ports in D3cold
+    - PCI: Add function 1 DMA alias quirk for Marvell 88SE9235
+    - PCI: qcom: Disable write access to read only registers for IP v2.3.3
+    - PCI: rockchip: Assert PCI Configuration Enable bit after probe
+    - PCI: rockchip: Write PCI Device ID to correct register
+    - PCI: rockchip: Add poll and timeout to wait for PHY PLLs to be locked
+    - PCI: rockchip: Fix legacy IRQ generation for RK3399 PCIe endpoint core
+    - PCI: rockchip: Use u32 variable to access 32-bit registers
+    - PCI: rockchip: Set address alignment for endpoint mode
+    - misc: pci_endpoint_test: Free IRQs before removing the device
+    - misc: pci_endpoint_test: Re-init completion for every test
+    - mfd: pm8008: Fix module autoloading
+    - md/raid0: add discard support for the 'original' layout
+    - dm init: add dm-mod.waitfor to wait for asynchronously probed block devices
+    - fs: dlm: return positive pid value for F_GETLK
+    - drm/atomic: Allow vblank-enabled + self-refresh "disable"
+    - drm/rockchip: vop: Leave vblank enabled in self-refresh
+    - drm/amdgpu: fix clearing mappings for BOs that are always valid in VM
+    - drm/amd/display: Correct `DMUB_FW_VERSION` macro
+    - drm/amdgpu: avoid restore process run into dead loop.
+    - drm/ttm: Don't leak a resource on swapout move error
+    - serial: atmel: don't enable IRQs prematurely
+    - tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in
+      case of error
+    - tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when
+      iterating clk
+    - tty: serial: imx: fix rs485 rx after tx
+    - firmware: stratix10-svc: Fix a potential resource leak in
+      svc_create_memory_pool()
+    - libceph: harden msgr2.1 frame segment length checks
+    - ceph: don't let check_caps skip sending responses for revoke msgs
+    - xhci: Fix resume issue of some ZHAOXIN hosts
+    - xhci: Fix TRB prefetch issue of ZHAOXIN hosts
+    - xhci: Show ZHAOXIN xHCI root hub speed correctly
+    - meson saradc: fix clock divider mask length
+    - opp: Fix use-after-free in lazy_opp_tables after probe deferral
+    - soundwire: qcom: fix storing port config out-of-bounds
+    - Revert "8250: add support for ASIX devices with a FIFO bug"
+    - bus: ixp4xx: fix IXP4XX_EXP_T1_MASK
+    - s390/decompressor: fix misaligned symbol build error
+    - tracing/histograms: Add histograms to hist_vars if they have referenced
+      variables
+    - tracing: Fix memory leak of iter->temp when reading trace_pipe
+    - samples: ftrace: Save required argument registers in sample trampolines
+    - net: ena: fix shift-out-of-bounds in exponential backoff
+    - ring-buffer: Fix deadloop issue on reading trace_pipe
+    - ftrace: Fix possible warning on checking all pages used in
+      ftrace_process_locs()
+    - xtensa: ISS: fix call to split_if_spec
+    - tracing: Fix null pointer dereference in tracing_err_log_open()
+    - selftests: mptcp: sockopt: return error if wrong mark
+    - selftests: mptcp: depend on SYN_COOKIES
+    - tracing/probes: Fix not to count error code to total length
+    - tracing/probes: Fix to update dynamic data counter if fetcharg uses it
+    - scsi: qla2xxx: Wait for io return on terminate rport
+    - scsi: qla2xxx: Array index may go out of bound
+    - scsi: qla2xxx: Avoid fcport pointer dereference
+    - scsi: qla2xxx: Fix buffer overrun
+    - scsi: qla2xxx: Fix potential NULL pointer dereference
+    - scsi: qla2xxx: Check valid rport returned by fc_bsg_to_rport()
+    - scsi: qla2xxx: Correct the index of array
+    - scsi: qla2xxx: Pointer may be dereferenced
+    - scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue
+    - MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
+    - net/sched: sch_qfq: reintroduce lmax bound check for MTU
+    - drm/atomic: Fix potential use-after-free in nonblocking commits
+    - Linux 5.15.121
+  * Jammy update: v5.15.120 upstream stable release (LP: #2032688)
+    - mptcp: fix possible divide by zero in recvmsg()
+    - mptcp: consolidate fallback and non fallback state machine
+    - mm, hwpoison: try to recover from copy-on write faults
+    - mm, hwpoison: when copy-on-write hits poison, take page offline
+    - drm/amdgpu: Set vmbo destroy after pt bo is created
+    - x86/microcode/AMD: Load late on both threads too
+    - x86/smp: Use dedicated cache-line for mwait_play_dead()
+    - can: isotp: isotp_sendmsg(): fix return error fix on TX path
+    - bpf: ensure main program has an extable
+    - HID: wacom: Use ktime_t rather than int when dealing with timestamps
+    - HID: logitech-hidpp: add HIDPP_QUIRK_DELAYED_INIT for the T651.
+    - Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak
+      in mtk_thermal_probe"
+    - perf symbols: Symbol lookup with kcore can fail if multiple segments match
+      stext
+    - scripts/tags.sh: Resolve gtags empty index generation
+    - drm/amdgpu: Validate VM ioctl flags.
+    - parisc: Delete redundant register definitions in <asm/assembly.h>
+    - nubus: Partially revert proc_create_single_data() conversion
+    - Linux 5.15.120
+  * Jammy update: v5.15.119 upstream stable release (LP: #2032683)
+    - drm/amd/display: fix the system hang while disable PSR
+    - tracing: Add tracing_reset_all_online_cpus_unlocked() function
+    - tpm, tpm_tis: Claim locality in interrupt handler
+    - drm/amd/display: Add minimal pipe split transition state
+    - drm/amd/display: Use dc_update_planes_and_stream
+    - drm/amd/display: Add wrapper to call planes and stream update
+    - tick/common: Align tick period during sched_timer setup
+    - selftests: mptcp: lib: skip if missing symbol
+    - selftests: mptcp: lib: skip if not below kernel version
+    - selftests/mount_setattr: fix redefine struct mount_attr build error
+    - selftests: mptcp: pm nl: remove hardcoded default limits
+    - selftests: mptcp: join: use 'iptables-legacy' if available
+    - selftests: mptcp: join: skip check if MIB counter not supported
+    - nilfs2: fix buffer corruption due to concurrent device reads
+    - ACPI: sleep: Avoid breaking S3 wakeup due to might_sleep()
+    - KVM: Avoid illegal stage2 mapping on invalid memory slot
+    - Drivers: hv: vmbus: Call hv_synic_free() if hv_synic_alloc() fails
+    - Drivers: hv: vmbus: Fix vmbus_wait_for_unload() to scan present CPUs
+    - PCI: hv: Fix a race condition bug in hv_pci_query_relations()
+    - Revert "PCI: hv: Fix a timing issue which causes kdump to fail occasionally"
+    - PCI: hv: Remove the useless hv_pcichild_state from struct hv_pci_dev
+    - PCI: hv: Fix a race condition in hv_irq_unmask() that can cause panic
+    - PCI: hv: Add a per-bus mutex state_lock
+    - cgroup: Do not corrupt task iteration when rebinding subsystem
+    - mmc: sdhci-msm: Disable broken 64-bit DMA on MSM8916
+    - mmc: meson-gx: remove redundant mmc_request_done() call from irq context
+    - mmc: mmci: stm32: fix max busy timeout calculation
+    - ip_tunnels: allow VXLAN/GENEVE to inherit TOS/TTL from VLAN
+    - regulator: pca9450: Fix LDO3OUT and LDO4OUT MASK
+    - regmap: spi-avmm: Fix regmap_bus max_raw_write
+    - writeback: fix dereferencing NULL mapping->host on writeback_page_template
+    - io_uring/net: save msghdr->msg_control for retries
+    - io_uring/net: clear msg_controllen on partial sendmsg retry
+    - io_uring/net: disable partial retries for recvmsg with cmsg
+    - nilfs2: prevent general protection fault in nilfs_clear_dirty_page()
+    - x86/mm: Avoid using set_pgd() outside of real PGD pages
+    - memfd: check for non-NULL file_seals in memfd_create() syscall
+    - mmc: meson-gx: fix deferred probing
+    - ieee802154: hwsim: Fix possible memory leaks
+    - xfrm: Treat already-verified secpath entries as optional
+    - xfrm: interface: rename xfrm_interface.c to xfrm_interface_core.c
+    - xfrm: Ensure policies always checked on XFRM-I input path
+    - bpf: track immediate values written to stack by BPF_ST instruction
+    - bpf: Fix verifier id tracking of scalars on spill
+    - xfrm: fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
+    - selftests: net: fcnal-test: check if FIPS mode is enabled
+    - xfrm: Linearize the skb after offloading if needed.
+    - net: qca_spi: Avoid high load if QCA7000 is not available
+    - mmc: mtk-sd: fix deferred probing
+    - mmc: mvsdio: fix deferred probing
+    - mmc: omap: fix deferred probing
+    - mmc: omap_hsmmc: fix deferred probing
+    - mmc: owl: fix deferred probing
+    - mmc: sdhci-acpi: fix deferred probing
+    - mmc: sh_mmcif: fix deferred probing
+    - mmc: usdhi60rol0: fix deferred probing
+    - ipvs: align inner_mac_header for encapsulation
+    - net: dsa: mt7530: fix trapping frames on non-MT7621 SoC MT7530 switch
+    - net: dsa: mt7530: fix handling of BPDUs on MT7530 switch
+    - be2net: Extend xmit workaround to BE3 chip
+    - netfilter: nft_set_pipapo: .walk does not deal with generations
+    - netfilter: nf_tables: disallow element updates of bound anonymous sets
+    - netfilter: nf_tables: reject unbound anonymous set before commit phase
+    - netfilter: nf_tables: reject unbound chain set before commit phase
+    - netfilter: nf_tables: disallow updates of anonymous sets
+    - netfilter: nfnetlink_osf: fix module autoload
+    - Revert "net: phy: dp83867: perform soft reset and retain established link"
+    - bpf/btf: Accept function names that contain dots
+    - selftests: forwarding: Fix race condition in mirror installation
+    - sch_netem: acquire qdisc lock in netem_change()
+    - gpio: Allow per-parent interrupt data
+    - gpiolib: Fix GPIO chip IRQ initialization restriction
+    - gpio: sifive: add missing check for platform_get_irq
+    - scsi: target: iscsi: Prevent login threads from racing between each other
+    - HID: wacom: Add error check to wacom_parse_and_register()
+    - arm64: Add missing Set/Way CMO encodings
+    - media: cec: core: don't set last_initiator if tx in progress
+    - nfcsim.c: Fix error checking for debugfs_create_dir
+    - usb: gadget: udc: fix NULL dereference in remove()
+    - nvme: double KA polling frequency to avoid KATO with TBKAS on
+    - Input: soc_button_array - add invalid acpi_index DMI quirk handling
+    - s390/cio: unregister device when the only path is gone
+    - spi: lpspi: disable lpspi module irq in DMA mode
+    - ASoC: simple-card: Add missing of_node_put() in case of error
+    - soundwire: dmi-quirks: add new mapping for HP Spectre x360
+    - ASoC: nau8824: Add quirk to active-high jack-detect
+    - s390/purgatory: disable branch profiling
+    - ARM: dts: Fix erroneous ADS touchscreen polarities
+    - drm/exynos: vidi: fix a wrong error return
+    - drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl
+    - drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl
+    - vhost_net: revert upend_idx only on retriable error
+    - x86/apic: Fix kernel panic when booting with intremap=off and x2apic_phys
+    - i2c: imx-lpi2c: fix type char overflow issue when calculating the clock
+      cycle
+    - act_mirred: remove unneded merge conflict markers
+    - Linux 5.15.119
+  * Jammy update: v5.15.118 upstream stable release (LP: #2030239)
+    - test_firmware: Use kstrtobool() instead of strtobool()
+    - test_firmware: prevent race conditions by a correct implementation of
+      locking
+    - test_firmware: fix a memory leak with reqs buffer
+    - ksmbd: fix slab-out-of-bounds read in smb2_handle_negotiate
+    - drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram
+    - of: overlay: rename variables to be consistent
+    - of: overlay: rework overlay apply and remove kfree()s
+    - of: overlay: Fix missing of_node_put() in error case of
+      init_overlay_changeset()
+    - power: supply: ab8500: Fix external_power_changed race
+    - power: supply: sc27xx: Fix external_power_changed race
+    - power: supply: bq27xxx: Use mod_delayed_work() instead of cancel() +
+      schedule()
+    - ARM: dts: vexpress: add missing cache properties
+    - tools: gpio: fix debounce_period_us output of lsgpio
+    - power: supply: Ratelimit no data debug output
+    - platform/x86: asus-wmi: Ignore WMI events with codes 0x7B, 0xC0
+    - regulator: Fix error checking for debugfs_create_dir
+    - irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issues
+    - power: supply: Fix logic checking if system is running from battery
+    - btrfs: scrub: try harder to mark RAID56 block groups read-only
+    - btrfs: handle memory allocation failure in btrfs_csum_one_bio
+    - ASoC: soc-pcm: test if a BE can be prepared
+    - parisc: Improve cache flushing for PCXL in arch_sync_dma_for_cpu()
+    - parisc: Flush gatt writes and adjust gatt mask in parisc_agp_mask_memory()
+    - MIPS: unhide PATA_PLATFORM
+    - MIPS: Alchemy: fix dbdma2
+    - mips: Move initrd_start check after initrd address sanitisation.
+    - ASoC: dwc: move DMA init to snd_soc_dai_driver probe()
+    - xen/blkfront: Only check REQ_FUA for writes
+    - drm:amd:amdgpu: Fix missing buffer object unlock in failure path
+    - NVMe: Add MAXIO 1602 to bogus nid list.
+    - irqchip/gic: Correctly validate OF quirk descriptors
+    - wifi: cfg80211: fix locking in regulatory disconnect
+    - wifi: cfg80211: fix double lock bug in reg_wdev_chan_valid()
+    - epoll: ep_autoremove_wake_function should use list_del_init_careful
+    - ocfs2: fix use-after-free when unmounting read-only filesystem
+    - ocfs2: check new file size on fallocate call
+    - nios2: dts: Fix tse_mac "max-frame-size" property
+    - nilfs2: fix incomplete buffer cleanup in nilfs_btnode_abort_change_key()
+    - nilfs2: fix possible out-of-bounds segment allocation in resize ioctl
+    - kexec: support purgatories with .text.hot sections
+    - x86/purgatory: remove PGO flags
+    - powerpc/purgatory: remove PGO flags
+    - ALSA: usb-audio: Add quirk flag for HEM devices to enable native DSD
+      playback
+    - dm thin metadata: check fail_io before using data_sm
+    - nouveau: fix client work fence deletion race
+    - RDMA/uverbs: Restrict usage of privileged QKEYs
+    - net: usb: qmi_wwan: add support for Compal RXM-G1
+    - drm/amdgpu: add missing radeon secondary PCI ID
+    - ALSA: hda/realtek: Add a quirk for Compaq N14JP6
+    - Remove DECnet support from kernel
+    - [Config] updateconfigs for DECNET
+    - thunderbolt: dma_test: Use correct value for absent rings when creating
+      paths
+    - thunderbolt: Mask ring interrupt on Intel hardware as well
+    - USB: serial: option: add Quectel EM061KGL series
+    - serial: lantiq: add missing interrupt ack
+    - usb: dwc3: gadget: Reset num TRBs before giving back the request
+    - RDMA/rtrs: Fix the last iu->buf leak in err path
+    - RDMA/rtrs: Fix rxe_dealloc_pd warning
+    - RDMA/rxe: Fix packet length checks
+    - spi: fsl-dspi: avoid SCK glitches with continuous transfers
+    - netfilter: nf_tables: integrate pipapo into commit protocol
+    - netfilter: nfnetlink: skip error delivery on batch in case of ENOMEM
+    - net: enetc: correct the indexes of highest and 2nd highest TCs
+    - ping6: Fix send to link-local addresses with VRF.
+    - net/sched: simplify tcf_pedit_act
+    - net/sched: act_pedit: remove extra check for key type
+    - net/sched: act_pedit: Parse L3 Header for L4 offset
+    - RDMA/rxe: Remove the unused variable obj
+    - RDMA/rxe: Removed unused name from rxe_task struct
+    - RDMA/rxe: Fix the use-before-initialization error of resp_pkts
+    - iavf: remove mask from iavf_irq_enable_queues()
+    - octeontx2-af: fixed resource availability check
+    - octeontx2-af: fix lbk link credits on cn10k
+    - RDMA/mlx5: Initiate dropless RQ for RAW Ethernet functions
+    - RDMA/cma: Always set static rate to 0 for RoCE
+    - IB/uverbs: Fix to consider event queue closing also upon non-blocking mode
+    - IB/isert: Fix dead lock in ib_isert
+    - IB/isert: Fix possible list corruption in CMA handler
+    - IB/isert: Fix incorrect release of isert connection
+    - net: ethtool: correct MAX attribute value for stats
+    - ipvlan: fix bound dev checking for IPv6 l3s mode
+    - sctp: fix an error code in sctp_sf_eat_auth()
+    - igc: Clean the TX buffer and TX descriptor ring
+    - igb: fix nvm.ops.read() error handling
+    - drm/nouveau: don't detect DSM for non-NVIDIA device
+    - drm/nouveau/dp: check for NULL nv_connector->native_mode
+    - drm/nouveau: add nv_encoder pointer check for NULL
+    - cifs: fix lease break oops in xfstest generic/098
+    - ext4: drop the call to ext4_error() from ext4_get_group_info()
+    - net/sched: cls_api: Fix lockup on flushing explicitly created chain
+    - net: lapbether: only support ethernet devices
+    - dm: don't lock fs when the map is NULL during suspend or resume
+    - net: tipc: resize nlattr array to correct size
+    - selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
+    - afs: Fix vlserver probe RTT handling
+    - cgroup: always put cset in cgroup_css_set_put_fork
+    - rcu/kvfree: Avoid freeing new kfree_rcu() memory after old grace period
+    - neighbour: Remove unused inline function neigh_key_eq16()
+    - net: Remove unused inline function dst_hold_and_use()
+    - net: Remove DECnet leftovers from flow.h.
+    - neighbour: delete neigh_lookup_nodev as not used
+    - of: overlay: add entry to of_overlay_action_name[]
+    - mmc: block: ensure error propagation for non-blk
+    - nilfs2: reject devices with insufficient block count
+    - Linux 5.15.118
+  * Jammy update: v5.15.117 upstream stable release (LP: #2030107)
+    - ata: ahci: fix enum constants for gcc-13
+    - gcc-plugins: Reorganize gimple includes for GCC 13
+    - remove the sx8 block driver
+    - [Config] updateconfigs for BLK_DEV_SX8
+    - sfc (gcc13): synchronize ef100_enqueue_skb()'s return type
+    - i40e: Remove string printing for i40e_status
+    - i40e: use int for i40e_status
+    - i40e: fix build warning in ice_fltr_add_mac_to_list()
+    - bonding (gcc13): synchronize bond_{a,t}lb_xmit() types
+    - f2fs: fix iostat lock protection
+    - blk-iocost: avoid 64-bit division in ioc_timer_fn
+    - platform/surface: aggregator: Allow completion work-items to be executed in
+      parallel
+    - spi: qup: Request DMA before enabling clocks
+    - afs: Fix setting of mtime when creating a file/dir/symlink
+    - wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll
+    - neighbour: fix unaligned access to pneigh_entry
+    - net: dsa: lan9303: allow vid != 0 in port_fdb_{add|del} methods
+    - bpf: Fix UAF in task local storage
+    - net/ipv6: fix bool/int mismatch for skip_notify_on_dev_down
+    - net/smc: Avoid to access invalid RMBs' MRs in SMCRv1 ADD LINK CONT
+    - net: enetc: correct the statistics of rx bytes
+    - net/sched: fq_pie: ensure reasonable TCA_FQ_PIE_QUANTUM values
+    - drm/i915: Explain the magic numbers for AUX SYNC/precharge length
+    - drm/i915: Use 18 fast wake AUX sync len
+    - Bluetooth: Fix l2cap_disconnect_req deadlock
+    - Bluetooth: L2CAP: Add missing checks for invalid DCID
+    - qed/qede: Fix scheduling while atomic
+    - wifi: cfg80211: fix locking in sched scan stop work
+    - selftests/bpf: Verify optval=NULL case
+    - selftests/bpf: Fix sockopt_sk selftest
+    - netfilter: conntrack: fix NULL pointer dereference in nf_confirm_cthelper
+    - netfilter: ipset: Add schedule point in call_ad().
+    - ipv6: rpl: Fix Route of Death.
+    - rfs: annotate lockless accesses to sk->sk_rxhash
+    - rfs: annotate lockless accesses to RFS sock flow table
+    - drm/i915/selftests: Increase timeout for live_parallel_switch
+    - drm/i915/selftests: Stop using kthread_stop()
+    - drm/i915/selftests: Add some missing error propagation
+    - net: sched: move rtm_tca_policy declaration to include file
+    - net: sched: act_police: fix sparse errors in tcf_police_dump()
+    - net: sched: fix possible refcount leak in tc_chain_tmplt_add()
+    - bpf: Add extra path pointer check to d_path helper
+    - lib: cpu_rmap: Fix potential use-after-free in irq_cpu_rmap_release()
+    - bnxt_en: Don't issue AP reset during ethtool's reset operation
+    - bnxt_en: Query default VLAN before VNIC setup on a VF
+    - bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks
+    - batman-adv: Broken sync while rescheduling delayed work
+    - Input: xpad - delete a Razer DeathAdder mouse VID/PID entry
+    - Input: psmouse - fix OOB access in Elantech protocol
+    - Input: fix open count when closing inhibited device
+    - ALSA: hda/realtek: Add quirk for Clevo NS50AU
+    - ALSA: hda/realtek: Add a quirk for HP Slim Desktop S01
+    - drm/i915/gt: Use the correct error value when kernel_context() fails
+    - drm/amd/pm: conditionally disable pcie lane switching for some
+      sienna_cichlid SKUs
+    - drm/amdgpu: fix xclk freq on CHIP_STONEY
+    - drm/amd/pm: Fix power context allocation in SMU13
+    - can: j1939: j1939_sk_send_loop_abort(): improved error queue handling in
+      J1939 Socket
+    - can: j1939: change j1939_netdev_lock type to mutex
+    - can: j1939: avoid possible use-after-free when j1939_can_rx_register fails
+    - ceph: fix use-after-free bug for inodes when flushing capsnaps
+    - s390/dasd: Use correct lock while counting channel queue length
+    - Bluetooth: Fix use-after-free in hci_remove_ltk/hci_remove_irk
+    - Bluetooth: hci_qca: fix debugfs registration
+    - tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta'
+    - rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting
+    - rbd: get snapshot context after exclusive lock is ensured to be held
+    - pinctrl: meson-axg: add missing GPIOA_18 gpio group
+    - usb: usbfs: Enforce page requirements for mmap
+    - usb: usbfs: Use consistent mmap functions
+    - ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
+    - ASoC: codecs: wsa881x: do not set can_multi_write flag
+    - arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite
+      boards
+    - arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
+    - arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
+    - ASoC: mediatek: mt8195-afe-pcm: Convert to platform remove callback
+      returning void
+    - ASoC: mediatek: mt8195: fix use-after-free in driver remove path
+    - arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
+    - i2c: mv64xxx: Fix reading invalid status value in atomic mode
+    - firmware: arm_ffa: Set handle field to zero in memory descriptor
+    - i2c: sprd: Delete i2c adapter in .remove's error path
+    - eeprom: at24: also select REGMAP
+    - riscv: fix kprobe __user string arg print fault issue
+    - vduse: avoid empty string for dev name
+    - vhost: support PACKED when setting-getting vring_base
+    - vhost_vdpa: support PACKED when setting-getting vring_base
+    - ext4: only check dquot_initialize_needed() when debugging
+    - Linux 5.15.117
+  * CVE-2023-4273
+    - exfat: check if filename entries exceeds max filename length
+  * CVE-2023-4128
+    - net/sched: cls_u32: No longer copy tcf_result on update to avoid use-after-
+      free
+    - net/sched: cls_fw: No longer copy tcf_result on update to avoid use-after-
+      free
+    - net/sched: cls_route: No longer copy tcf_result on update to avoid use-
+      after-free
+  * CVE-2023-3863
+    - nfc: llcp: simplify llcp_sock_connect() error paths
+    - net: nfc: Fix use-after-free caused by nfc_llcp_find_local
+
+  [ Ubuntu: 5.15.0-83.92 ]
+
+  * jammy/linux: 5.15.0-83.92 -proposed tracker (LP: #2031132)
+  * libgnutls report "trap invalid opcode" when trying to install packages over
+    https (LP: #2031093)
+    - [Config]: disable CONFIG_GDS_FORCE_MITIGATION
+
+  [ Ubuntu: 5.15.0-81.90 ]
+
+  * jammy/linux: 5.15.0-81.90 -proposed tracker (LP: #2030422)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] resync getabis
+    - debian/dkms-versions -- update from kernel-versions (main/2023.08.07)
+  * CVE-2022-40982
+    - x86/mm: Initialize text poking earlier
+    - x86/mm: fix poking_init() for Xen PV guests
+    - x86/mm: Use mm_alloc() in poking_init()
+    - mm: Move mm_cachep initialization to mm_init()
+    - init: Provide arch_cpu_finalize_init()
+    - x86/cpu: Switch to arch_cpu_finalize_init()
+    - ARM: cpu: Switch to arch_cpu_finalize_init()
+    - sparc/cpu: Switch to arch_cpu_finalize_init()
+    - um/cpu: Switch to arch_cpu_finalize_init()
+    - init: Remove check_bugs() leftovers
+    - init: Invoke arch_cpu_finalize_init() earlier
+    - init, x86: Move mem_encrypt_init() into arch_cpu_finalize_init()
+    - x86/init: Initialize signal frame size late
+    - x86/fpu: Remove cpuinfo argument from init functions
+    - x86/fpu: Mark init functions __init
+    - x86/fpu: Move FPU initialization into arch_cpu_finalize_init()
+    - x86/xen: Fix secondary processors' FPU initialization
+    - x86/speculation: Add Gather Data Sampling mitigation
+    - x86/speculation: Add force option to GDS mitigation
+    - x86/speculation: Add Kconfig option for GDS
+    - KVM: Add GDS_NO support to KVM
+    - Documentation/x86: Fix backwards on/off logic about YMM support
+    - [Config]: Enable CONFIG_ARCH_HAS_CPU_FINALIZE_INIT and
+      CONFIG_GDS_FORCE_MITIGATION
+  * CVE-2023-3609
+    - net/sched: cls_u32: Fix reference counter leak leading to overflow
+  * CVE-2023-21400
+    - io_uring: ensure IOPOLL locks around deferred work
+  * CVE-2023-4015
+    - netfilter: nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound
+      set/chain
+    - netfilter: nf_tables: unbind non-anonymous set if rule construction fails
+    - netfilter: nf_tables: skip immediate deactivate in _PREPARE_ERROR
+  * CVE-2023-3995
+    - netfilter: nf_tables: disallow rule addition to bound chain via
+      NFTA_RULE_CHAIN_ID
+  * CVE-2023-3777
+    - netfilter: nf_tables: skip bound chain on rule flush
+  * losetup with mknod fails on jammy with kernel 5.15.0-69-generic
+    (LP: #2015400)
+    - loop: do not enforce max_loop hard limit by (new) default
+  * Include the MAC address pass through function on RTL8153DD-CG (LP: #2020295)
+    - r8152: add USB device driver for config selection
+  * Jammy update: v5.15.116 upstream stable release (LP: #2029401)
+    - RDMA/bnxt_re: Fix the page_size used during the MR creation
+    - RDMA/efa: Fix unsupported page sizes in device
+    - RDMA/hns: Fix base address table allocation
+    - RDMA/hns: Modify the value of long message loopback slice
+    - dmaengine: at_xdmac: Move the free desc to the tail of the desc list
+    - dmaengine: at_xdmac: fix potential Oops in at_xdmac_prep_interleaved()
+    - RDMA/bnxt_re: Fix a possible memory leak
+    - RDMA/bnxt_re: Fix return value of bnxt_re_process_raw_qp_pkt_rx
+    - iommu/rockchip: Fix unwind goto issue
+    - iommu/amd: Don't block updates to GATag if guest mode is on
+    - dmaengine: pl330: rename _start to prevent build error
+    - riscv: Fix unused variable warning when BUILTIN_DTB is set
+    - net/mlx5: fw_tracer, Fix event handling
+    - net/mlx5e: Don't attach netdev profile while handling internal error
+    - net: mellanox: mlxbf_gige: Fix skb_panic splat under memory pressure
+    - netrom: fix info-leak in nr_write_internal()
+    - af_packet: Fix data-races of pkt_sk(sk)->num.
+    - amd-xgbe: fix the false linkup in xgbe_phy_status
+    - mtd: rawnand: ingenic: fix empty stub helper definitions
+    - RDMA/irdma: Add SW mechanism to generate completions on error
+    - RDMA/irdma: Prevent QP use after free
+    - RDMA/irdma: Fix Local Invalidate fencing
+    - af_packet: do not use READ_ONCE() in packet_bind()
+    - tcp: deny tcp_disconnect() when threads are waiting
+    - tcp: Return user_mss for TCP_MAXSEG in CLOSE/LISTEN state if user_mss set
+    - net/sched: sch_ingress: Only create under TC_H_INGRESS
+    - net/sched: sch_clsact: Only create under TC_H_CLSACT
+    - net/sched: Reserve TC_H_INGRESS (TC_H_CLSACT) for ingress (clsact) Qdiscs
+    - net/sched: Prohibit regrafting ingress or clsact Qdiscs
+    - net: sched: fix NULL pointer dereference in mq_attach
+    - net/netlink: fix NETLINK_LIST_MEMBERSHIPS length report
+    - udp6: Fix race condition in udp6_sendmsg & connect
+    - net/mlx5e: Fix error handling in mlx5e_refresh_tirs
+    - net/mlx5: Read embedded cpu after init bit cleared
+    - net: dsa: mv88e6xxx: Increase wait after reset deactivation
+    - mtd: rawnand: marvell: ensure timing values are written
+    - mtd: rawnand: marvell: don't set the NAND frequency select
+    - rtnetlink: call validate_linkmsg in rtnl_create_link
+    - drm/amdgpu: release gpu full access after "amdgpu_device_ip_late_init"
+    - watchdog: menz069_wdt: fix watchdog initialisation
+    - ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
+    - drm/amdgpu: Use the default reset when loading or reloading the driver
+    - mailbox: mailbox-test: Fix potential double-free in
+      mbox_test_message_write()
+    - drm/ast: Fix ARM compatibility
+    - btrfs: abort transaction when sibling keys check fails for leaves
+    - ARM: 9295/1: unwind:fix unwind abort for uleb128 case
+    - media: rcar-vin: Select correct interrupt mode for V4L2_FIELD_ALTERNATE
+    - platform/x86: intel_scu_pcidrv: Add back PCI ID for Medfield
+    - gfs2: Don't deref jdesc in evict
+    - fbdev: imsttfb: Fix use after free bug in imsttfb_probe
+    - fbdev: modedb: Add 1920x1080 at 60 Hz video mode
+    - fbdev: stifb: Fix info entry in sti_struct on error path
+    - nbd: Fix debugfs_create_dir error checking
+    - block/rnbd: replace REQ_OP_FLUSH with REQ_OP_WRITE
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for HS-SSD-FUTURE 2048G
+    - nvme-pci: add quirk for missing secondary temperature thresholds
+    - ASoC: dwc: limit the number of overrun messages
+    - um: harddog: fix modular build
+    - xfrm: Check if_id in inbound policy/secpath match
+    - ASoC: dt-bindings: Adjust #sound-dai-cells on TI's single-DAI codecs
+    - ASoC: ssm2602: Add workaround for playback distortions
+    - media: dvb_demux: fix a bug for the continuity counter
+    - media: dvb-usb: az6027: fix three null-ptr-deref in az6027_i2c_xfer()
+    - media: dvb-usb-v2: ec168: fix null-ptr-deref in ec168_i2c_xfer()
+    - media: dvb-usb-v2: ce6230: fix null-ptr-deref in ce6230_i2c_master_xfer()
+    - media: dvb-usb-v2: rtl28xxu: fix null-ptr-deref in rtl28xxu_i2c_xfer
+    - media: dvb-usb: digitv: fix null-ptr-deref in digitv_i2c_xfer()
+    - media: dvb-usb: dw2102: fix uninit-value in su3000_read_mac_address
+    - media: netup_unidvb: fix irq init by register it at the end of probe
+    - media: dvb_ca_en50221: fix a size write bug
+    - media: ttusb-dec: fix memory leak in ttusb_dec_exit_dvb()
+    - media: mn88443x: fix !CONFIG_OF error by drop of_match_ptr from ID table
+    - media: dvb-core: Fix use-after-free due on race condition at dvb_net
+    - media: dvb-core: Fix use-after-free due to race at dvb_register_device()
+    - media: dvb-core: Fix use-after-free due to race condition at dvb_ca_en50221
+    - s390/pkey: zeroize key blobs
+    - s390/topology: honour nr_cpu_ids when adding CPUs
+    - ACPI: resource: Add IRQ override quirk for LG UltraPC 17U70P
+    - wifi: rtl8xxxu: fix authentication timeout due to incorrect RCR value
+    - ARM: dts: stm32: add pin map for CAN controller on stm32f7
+    - arm64/mm: mark private VM_FAULT_X defines as vm_fault_t
+    - arm64: vdso: Pass (void *) to virt_to_page()
+    - wifi: mac80211: simplify chanctx allocation
+    - scsi: core: Decrease scsi_device's iorequest_cnt if dispatch failed
+    - wifi: b43: fix incorrect __packed annotation
+    - netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with
+      CONFIG_NF_NAT
+    - nvme-multipath: don't call blk_mark_disk_dead in nvme_mpath_remove_disk
+    - ALSA: oss: avoid missing-prototype warnings
+    - drm/msm: Be more shouty if per-process pgtables aren't working
+    - atm: hide unused procfs functions
+    - drm/amdgpu: skip disabling fence driver src_irqs when device is unplugged
+    - nvme-pci: Add quirk for Teamgroup MP33 SSD
+    - mailbox: mailbox-test: fix a locking issue in mbox_test_message_write()
+    - media: uvcvideo: Don't expose unsupported formats to userspace
+    - iio: accel: st_accel: Fix invalid mount_matrix on devices without ACPI _ONT
+      method
+    - iio: adc: mxs-lradc: fix the order of two cleanup operations
+    - HID: google: add jewel USB id
+    - HID: wacom: avoid integer overflow in wacom_intuos_inout()
+    - iio: imu: inv_icm42600: fix timestamp reset
+    - dt-bindings: iio: adc: renesas,rcar-gyroadc: Fix adi,ad7476 compatible value
+    - iio: light: vcnl4035: fixed chip ID check
+    - iio: adc: ad_sigma_delta: Fix IRQ issue by setting IRQ_DISABLE_UNLAZY flag
+    - iio: dac: mcp4725: Fix i2c_master_send() return value handling
+    - iio: adc: ad7192: Change "shorted" channels to differential
+    - iio: dac: build ad5758 driver when AD5758 is selected
+    - net: usb: qmi_wwan: Set DTR quirk for BroadMobi BM818
+    - dt-bindings: usb: snps,dwc3: Fix "snps,hsphy_interface" type
+    - usb: gadget: f_fs: Add unbind event before functionfs_unbind
+    - md/raid5: fix miscalculation of 'end_sector' in raid5_read_one_chunk()
+    - misc: fastrpc: return -EPIPE to invocations on device removal
+    - misc: fastrpc: reject new invocations during device removal
+    - scsi: stex: Fix gcc 13 warnings
+    - ata: libata-scsi: Use correct device no in ata_find_dev()
+    - drm/amd/pm: reverse mclk and fclk clocks levels for vangogh
+    - drm/amd/pm: reverse mclk and fclk clocks levels for yellow carp
+    - drm/amd/pm: reverse mclk and fclk clocks levels for renoir
+    - x86/boot: Wrap literal addresses in absolute_pointer()
+    - ath6kl: Use struct_group() to avoid size-mismatched casting
+    - block/blk-iocost (gcc13): keep large values in a new enum
+    - mmc: vub300: fix invalid response handling
+    - mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order
+    - tty: serial: fsl_lpuart: use UARTCTRL_TXINV to send break instead of
+      UARTCTRL_SBK
+    - btrfs: fix csum_tree_block page iteration to avoid tripping on
+      -Werror=array-bounds
+    - powerpc/iommu: Limit number of TCEs to 512 for H_STUFF_TCE hcall
+    - iommu/amd: Fix domain flush size when syncing iotlb
+    - usb: cdns3: allocate TX FIFO size according to composite EP number
+    - usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM
+    - block: fix revalidate performance regression
+    - selinux: don't use make's grouped targets feature yet
+    - tracing/probe: trace_probe_primary_from_call(): checked list_first_entry
+    - selftests: mptcp: connect: skip if MPTCP is not supported
+    - selftests: mptcp: pm nl: skip if MPTCP is not supported
+    - selftests: mptcp: sockopt: skip if MPTCP is not supported
+    - ext4: add EA_INODE checking to ext4_iget()
+    - ext4: set lockdep subclass for the ea_inode in ext4_xattr_inode_cache_find()
+    - ext4: disallow ea_inodes with extended attributes
+    - ext4: add lockdep annotations for i_data_sem for ea_inode's
+    - fbcon: Fix null-ptr-deref in soft_cursor
+    - serial: 8250_tegra: Fix an error handling path in tegra_uart_probe()
+    - test_firmware: fix the memory leak of the allocated firmware buffer
+    - KVM: x86: Account fastpath-only VM-Exits in vCPU stats
+    - ksmbd: fix credit count leakage
+    - ksmbd: fix incorrect AllocationSize set in smb2_get_info
+    - KEYS: asymmetric: Copy sig and digest in public_key_verify_signature()
+    - regmap: Account for register length when chunking
+    - tpm, tpm_tis: Request threaded interrupt handler
+    - drm/rcar: stop using 'imply' for dependencies
+    - [Config] updateconfigs for DRM_RCAR_LVDS
+    - scsi: dpt_i2o: Remove broken pass-through ioctl (I2OUSERCMD)
+    - scsi: dpt_i2o: Do not process completions with invalid addresses
+    - [Config] updateconfigs for SCSI_DPT_I2O
+    - drm/amdgpu/gfx10: Disable gfxoff before disabling powergating.
+    - selftests: mptcp: diag: skip if MPTCP is not supported
+    - selftests: mptcp: simult flows: skip if MPTCP is not supported
+    - selftests: mptcp: join: skip if MPTCP is not supported
+    - ext4: enable the lazy init thread when remounting read/write
+    - ARM: defconfig: drop CONFIG_DRM_RCAR_LVDS
+    - RDMA/irdma: Fix drain SQ hang with no completion
+    - RDMA/irdma: Do not generate SW completions for NOPs
+    - Linux 5.15.116
+  * CVE-2023-20593
+    - x86/cpu/amd: Move the errata checking functionality up
+    - x86/cpu/amd: Add a Zenbleed fix
+  * CVE-2023-4004
+    - netfilter: nft_set_pipapo: fix improper element removal
+  * CVE-2023-3611
+    - net/sched: sch_qfq: refactor parsing of netlink parameters
+    - net/sched: sch_qfq: account for stab overhead in qfq_enqueue
+  * CVE-2023-3610
+    - netfilter: nf_tables: fix chain binding transaction logic
+  * CVE-2023-2898
+    - f2fs: fix to avoid NULL pointer dereference f2fs_write_end_io()
+  * Backport support to tolerate ZSTD compressed firmware files (LP: #2028550)
+    - firmware_loader: EXTRA_FIRMWARE does not support compressed files
+    - firmware: Add the support for ZSTD-compressed firmware files
+    - [Config] Enable FW_LOADER_COMPRESS_ZSTD by default
+  * stacked overlay file system mounts that have chroot() called against them
+    appear to be getting locked (by the kernel most likely?) (LP: #2016398)
+    - SAUCE: overlayfs: fix reference count mismatch
+  * kdump fails on big arm64 systems when offset is not specified (LP: #2024479)
+    - arm64: mm: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
+    - arm64: kdump: Reimplement crashkernel=X
+    - docs: kdump: Update the crashkernel description for arm64
+    - arm64: kdump: Do not allocate crash low memory if not needed
+    - arm64/mm: Define defer_reserve_crashkernel()
+    - arm64: kdump: Provide default size when crashkernel=Y, low is not specified
+    - arm64: kdump: Support crashkernel=X fall back to reserve region above DMA
+      zones
+  * usbrtl sometimes doesn't reload firmware (LP: #2026028)
+    - Bluetooth: btrtl: Ask ic_info to drop firmware
+  * cifs: fix mid leak during reconnection after timeout threshold
+    (LP: #2029138)
+    - cifs: fix mid leak during reconnection after timeout threshold
+  * Jammy update: v5.15.115 upstream stable release (LP: #2028799)
+    - power: supply: bq27xxx: expose battery data when CI=1
+    - power: supply: bq27xxx: Move bq27xxx_battery_update() down
+    - power: supply: bq27xxx: Ensure power_supply_changed() is called on current
+      sign changes
+    - power: supply: bq27xxx: After charger plug in/out wait 0.5s for things to
+      stabilize
+    - power: supply: core: Refactor
+      power_supply_set_input_current_limit_from_supplier()
+    - power: supply: bq24190: Call power_supply_changed() after updating input
+      current
+    - bpf: fix a memory leak in the LRU and LRU_PERCPU hash maps
+    - net/mlx5: devcom only supports 2 ports
+    - net/mlx5e: Fix deadlock in tc route query code
+    - net/mlx5: Devcom, serialize devcom registration
+    - platform/x86: ISST: PUNIT device mapping with Sub-NUMA clustering
+    - platform/x86: ISST: Remove 8 socket limit
+    - net: phy: mscc: enable VSC8501/2 RGMII RX clock
+    - net: dsa: introduce helpers for iterating through ports using dp
+    - net: dsa: mt7530: rework mt753[01]_setup
+    - net: dsa: mt7530: split-off common parts from mt7531_setup
+    - net: dsa: mt7530: fix network connectivity with multiple CPU ports
+    - Bonding: add arp_missed_max option
+    - bonding: fix send_peer_notif overflow
+    - binder: fix UAF caused by faulty buffer cleanup
+    - irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()
+    - irqchip/mips-gic: Use raw spinlock for gic_lock
+    - net/mlx5e: Fix SQ wake logic in ptp napi_poll context
+    - xdp: Allow registering memory model without rxq reference
+    - net: page_pool: use in_softirq() instead
+    - page_pool: fix inconsistency for page_pool_ring_[un]lock()
+    - irqchip/mips-gic: Don't touch vl_map if a local interrupt is not routable
+    - xdp: xdp_mem_allocator can be NULL in trace_mem_connect().
+    - bluetooth: Add cmd validity checks at the start of hci_sock_ioctl()
+    - Revert "binder_alloc: add missing mmap_lock calls when using the VMA"
+    - Revert "android: binder: stop saving a pointer to the VMA"
+    - binder: add lockless binder_alloc_(set|get)_vma()
+    - binder: fix UAF of alloc->vma in race with munmap()
+    - ipv{4,6}/raw: fix output xfrm lookup wrt protocol
+    - netfilter: ctnetlink: Support offloaded conntrack entry deletion
+    - Linux 5.15.115
+  * Jammy update: v5.15.114 upstream stable release (LP: #2028701)
+    - usb: gadget: Properly configure the device for remote wakeup
+    - usb: dwc3: fix gadget mode suspend interrupt handler issue
+    - dt-bindings: ata: ahci-ceva: convert to yaml
+    - dt-bindings: ata: ahci-ceva: Cover all 4 iommus entries
+    - watchdog: sp5100_tco: Immediately trigger upon starting.
+    - ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
+    - spi: fsl-spi: Re-organise transfer bits_per_word adaptation
+    - spi: fsl-cpm: Use 16 bit mode for large transfers with even size
+    - ocfs2: Switch to security_inode_init_security()
+    - arm64: Also reset KASAN tag if page is not PG_mte_tagged
+    - ALSA: hda/ca0132: add quirk for EVGA X299 DARK
+    - ALSA: hda: Fix unhandled register update during auto-suspend period
+    - ALSA: hda/realtek: Enable headset onLenovo M70/M90
+    - mmc: sdhci-esdhc-imx: make "no-mmc-hs400" works
+    - ASoC: rt5682: Disable jack detection interrupt during suspend
+    - net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize
+    - m68k: Move signal frame following exception on 68020/030
+    - parisc: Handle kgdb breakpoints only in kernel context
+    - parisc: Allow to reboot machine after system halt
+    - gpio: mockup: Fix mode of debugfs files
+    - btrfs: use nofs when cleaning up aborted transactions
+    - dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size type
+    - selftests/memfd: Fix unknown type name build failure
+    - parisc: Fix flush_dcache_page() for usage from irq context
+    - perf/x86/uncore: Correct the number of CHAs on SPR
+    - x86/topology: Fix erroneous smp_num_siblings on Intel Hybrid platforms
+    - debugobjects: Don't wake up kswapd from fill_pool()
+    - fbdev: udlfb: Fix endpoint check
+    - net: fix stack overflow when LRO is disabled for virtual interfaces
+    - udplite: Fix NULL pointer dereference in __sk_mem_raise_allocated().
+    - USB: core: Add routines for endpoint checks in old drivers
+    - USB: sisusbvga: Add endpoint checks
+    - media: radio-shark: Add endpoint checks
+    - ASoC: lpass: Fix for KASAN use_after_free out of bounds
+    - net: fix skb leak in __skb_tstamp_tx()
+    - selftests: fib_tests: mute cleanup error message
+    - octeontx2-pf: Fix TSOv6 offload
+    - bpf: Fix mask generation for 32-bit narrow loads of 64-bit fields
+    - ipv6: Fix out-of-bounds access in ipv6_find_tlv()
+    - cifs: mapchars mount option ignored
+    - power: supply: leds: Fix blink to LED on transition
+    - power: supply: mt6360: add a check of devm_work_autocancel in
+      mt6360_charger_probe
+    - power: supply: bq27xxx: Fix bq27xxx_battery_update() race condition
+    - power: supply: bq27xxx: Fix I2C IRQ race on remove
+    - power: supply: bq27xxx: Fix poll_interval handling and races on remove
+    - power: supply: bq27xxx: Add cache parameter to
+      bq27xxx_battery_current_and_status()
+    - power: supply: sbs-charger: Fix INHIBITED bit for Status reg
+    - firmware: arm_ffa: Check if ffa_driver remove is present before executing
+    - firmware: arm_ffa: Fix FFA device names for logical partitions
+    - fs: fix undefined behavior in bit shift for SB_NOUSER
+    - regulator: pca9450: Fix BUCK2 enable_mask
+    - coresight: Fix signedness bug in tmc_etr_buf_insert_barrier_packet()
+    - xen/pvcalls-back: fix double frees with pvcalls_new_active_socket()
+    - x86/show_trace_log_lvl: Ensure stack pointer is aligned, again
+    - ASoC: Intel: Skylake: Fix declaration of enum skl_ch_cfg
+    - sctp: fix an issue that plpmtu can never go to complete state
+    - forcedeth: Fix an error handling path in nv_probe()
+    - platform/mellanox: mlxbf-pmc: fix sscanf() error checking
+    - net/mlx5e: do as little as possible in napi poll when budget is 0
+    - net/mlx5: DR, Fix crc32 calculation to work on big-endian (BE) CPUs
+    - net/mlx5: DR, Check force-loopback RC QP capability independently from RoCE
+    - net/mlx5: Fix error message when failing to allocate device memory
+    - net/mlx5: Devcom, fix error flow in mlx5_devcom_register_device
+    - arm64: dts: imx8mn-var-som: fix PHY detection bug by adding deassert delay
+    - firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors
+    - regulator: mt6359: add read check for PMIC MT6359
+    - 3c589_cs: Fix an error handling path in tc589_probe()
+    - net: phy: mscc: add VSC8502 to MODULE_DEVICE_TABLE
+    - Linux 5.15.114
+  * Jammy update: v5.15.113 upstream stable release (LP: #2028408)
+    - drm/mipi-dsi: Set the fwnode for mipi_dsi_device
+    - ARM: 9296/1: HP Jornada 7XX: fix kernel-doc warnings
+    - net: mdio: mvusb: Fix an error handling path in mvusb_mdio_probe()
+    - scsi: ufs: core: Fix I/O hang that occurs when BKOPS fails in W-LUN suspend
+    - tick/broadcast: Make broadcast device replacement work correctly
+    - linux/dim: Do nothing if no time delta between samples
+    - net: stmmac: switch to use interrupt for hw crosstimestamping
+    - net: stmmac: Initialize MAC_ONEUS_TIC_COUNTER register
+    - net: Fix load-tearing on sk->sk_stamp in sock_recv_cmsgs().
+    - netfilter: nf_tables: always release netdev hooks from notifier
+    - netfilter: conntrack: fix possible bug_on with enable_hooks=1
+    - netlink: annotate accesses to nlk->cb_running
+    - net: annotate sk->sk_err write from do_recvmmsg()
+    - net: deal with most data-races in sk_wait_event()
+    - net: add vlan_get_protocol_and_depth() helper
+    - tcp: add annotations around sk->sk_shutdown accesses
+    - gve: Remove the code of clearing PBA bit
+    - net: datagram: fix data-races in datagram_poll()
+    - af_unix: Fix a data race of sk->sk_receive_queue->qlen.
+    - af_unix: Fix data races around sk->sk_shutdown.
+    - drm/i915/dp: prevent potential div-by-zero
+    - fbdev: arcfb: Fix error handling in arcfb_probe()
+    - ext4: remove an unused variable warning with CONFIG_QUOTA=n
+    - ext4: reflect error codes from ext4_multi_mount_protect() to its callers
+    - ext4: fix lockdep warning when enabling MMP
+    - ext4: allow to find by goal if EXT4_MB_HINT_GOAL_ONLY is set
+    - ext4: allow ext4_get_group_info() to fail
+    - refscale: Move shutdown from wait_event() to wait_event_idle()
+    - rcu: Protect rcu_print_task_exp_stall() ->exp_tasks access
+    - fs: hfsplus: remove WARN_ON() from hfsplus_cat_{read,write}_inode()
+    - drm/displayid: add displayid_get_header() and check bounds better
+    - drm/amd/display: Use DC_LOG_DC in the trasform pixel function
+    - regmap: cache: Return error in cache sync operations for REGCACHE_NONE
+    - arm64: dts: qcom: msm8996: Add missing DWC3 quirks
+    - media: cx23885: Fix a null-ptr-deref bug in buffer_prepare() and
+      buffer_finish()
+    - media: pci: tw68: Fix null-ptr-deref bug in buf prepare and finish
+    - firmware: arm_sdei: Fix sleep from invalid context BUG
+    - ACPI: EC: Fix oops when removing custom query handlers
+    - remoteproc: stm32_rproc: Add mutex protection for workqueue
+    - drm/tegra: Avoid potential 32-bit integer overflow
+    - drm/msm/dp: Clean up handling of DP AUX interrupts
+    - ACPICA: Avoid undefined behavior: applying zero offset to null pointer
+    - ACPICA: ACPICA: check null return of ACPI_ALLOCATE_ZEROED in
+      acpi_db_display_objects
+    - drm/amd: Fix an out of bounds error in BIOS parser
+    - media: Prefer designated initializers over memset for subdev pad ops
+    - wifi: ath: Silence memcpy run-time false positive warning
+    - bpf: Annotate data races in bpf_local_storage
+    - wifi: brcmfmac: cfg80211: Pass the PMK in binary instead of hex
+    - ext2: Check block size validity during mount
+    - scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow
+    - bnxt: avoid overflow in bnxt_get_nvram_directory()
+    - net: pasemi: Fix return type of pasemi_mac_start_tx()
+    - net: Catch invalid index in XPS mapping
+    - scsi: target: iscsit: Free cmds before session free
+    - lib: cpu_rmap: Avoid use after free on rmap->obj array entries
+    - scsi: message: mptlan: Fix use after free bug in mptlan_remove() due to race
+      condition
+    - gfs2: Fix inode height consistency check
+    - scsi: ufs: ufs-pci: Add support for Intel Lunar Lake
+    - ext4: set goal start correctly in ext4_mb_normalize_request
+    - ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()
+    - f2fs: fix to drop all dirty pages during umount() if cp_error is set
+    - f2fs: fix to check readonly condition correctly
+    - samples/bpf: Fix fout leak in hbm's run_bpf_prog
+    - bpf: Add preempt_count_{sub,add} into btf id deny list
+    - wifi: iwlwifi: pcie: fix possible NULL pointer dereference
+    - wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf
+    - null_blk: Always check queue mode setting from configfs
+    - wifi: iwlwifi: dvm: Fix memcpy: detected field-spanning write backtrace
+    - wifi: ath11k: Fix SKB corruption in REO destination ring
+    - nbd: fix incomplete validation of ioctl arg
+    - ipvs: Update width of source for ip_vs_sync_conn_options
+    - Bluetooth: btintel: Add LE States quirk support
+    - Bluetooth: hci_bcm: Fall back to getting bdaddr from EFI if not set
+    - Bluetooth: L2CAP: fix "bad unlock balance" in l2cap_disconnect_rsp
+    - HID: logitech-hidpp: Don't use the USB serial for USB devices
+    - HID: logitech-hidpp: Reconcile USB and Unifying serials
+    - spi: spi-imx: fix MX51_ECSPI_* macros when cs > 3
+    - HID: wacom: generic: Set battery quirk only when we see battery data
+    - usb: typec: tcpm: fix multiple times discover svids error
+    - serial: 8250: Reinit port->pm on port specific driver unbind
+    - mcb-pci: Reallocate memory region to avoid memory overlapping
+    - sched: Fix KCSAN noinstr violation
+    - recordmcount: Fix memory leaks in the uwrite function
+    - RDMA/core: Fix multiple -Warray-bounds warnings
+    - iommu/arm-smmu-qcom: Limit the SMR groups to 128
+    - fs/ntfs3: Fix NULL pointer dereference in 'ni_write_inode'
+    - fs/ntfs3: Enhance the attribute size check
+    - fs/ntfs3: Fix NULL dereference in ni_write_inode
+    - fs/ntfs3: Validate MFT flags before replaying logs
+    - fs/ntfs3: Add length check in indx_get_root
+    - fs/ntfs3: Fix a possible null-pointer dereference in ni_clear()
+    - clk: tegra20: fix gcc-7 constant overflow warning
+    - iommu/arm-smmu-v3: Acknowledge pri/event queue overflow if any
+    - iommu/sprd: Release dma buffer to avoid memory leak
+    - Input: xpad - add constants for GIP interface numbers
+    - phy: st: miphy28lp: use _poll_timeout functions for waits
+    - soundwire: qcom: gracefully handle too many ports in DT
+    - mfd: dln2: Fix memory leak in dln2_probe()
+    - parisc: Replace regular spinlock with spin_trylock on panic path
+    - platform/x86: hp-wmi: Support touchpad on/off
+    - [Config] updateconfigs for X86_PLATFORM_DRIVERS_HP
+    - platform/x86: Move existing HP drivers to a new hp subdir
+    - platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct
+    - xfrm: don't check the default policy if the policy allows the packet
+    - Revert "Fix XFRM-I support for nested ESP tunnels"
+    - drm/msm/dp: unregister audio driver during unbind
+    - drm/msm/dpu: Add INTF_5 interrupts
+    - drm/msm/dpu: Move non-MDP_TOP INTF_INTR offsets out of hwio header
+    - drm/msm/dpu: Remove duplicate register defines from INTF
+    - dt-bindings: display/msm: dsi-controller-main: Document qcom, master-dsi and
+      qcom, sync-dual-dsi
+    - ASoC: fsl_micfil: Fix error handler with pm_runtime_enable
+    - cpupower: Make TSC read per CPU for Mperf monitor
+    - af_key: Reject optional tunnel/BEET mode templates in outbound policies
+    - selftests: seg6: disable DAD on IPv6 router cfg for srv6_end_dt4_l3vpn_test
+    - selftets: seg6: disable rp_filter by default in srv6_end_dt4_l3vpn_test
+    - net: fec: Better handle pm_runtime_get() failing in .remove()
+    - net: phy: dp83867: add w/a for packet errors seen with short cables
+    - ALSA: firewire-digi00x: prevent potential use after free
+    - ALSA: hda/realtek: Apply HP B&O top speaker profile to Pavilion 15
+    - vsock: avoid to close connected socket after the timeout
+    - tcp: fix possible sk_priority leak in tcp_v4_send_reset()
+    - serial: arc_uart: fix of_iomap leak in `arc_serial_probe`
+    - serial: 8250_bcm7271: balance clk_enable calls
+    - serial: 8250_bcm7271: fix leak in `brcmuart_probe`
+    - erspan: get the proto with the md version for collect_md
+    - net: hns3: fix output information incomplete for dumping tx queue info with
+      debugfs
+    - net: hns3: fix sending pfc frames after reset issue
+    - net: hns3: fix reset delay time to avoid configuration timeout
+    - media: netup_unidvb: fix use-after-free at del_timer()
+    - SUNRPC: double free xprt_ctxt while still in use
+    - tracing: Introduce helpers to safely handle dynamic-sized sockaddrs
+    - SUNRPC: Clean up svc_deferred_class trace events
+    - SUNRPC: Remove dead code in svc_tcp_release_rqst()
+    - SUNRPC: Remove svc_rqst::rq_xprt_hlen
+    - SUNRPC: always free ctxt when freeing deferred request
+    - SUNRPC: Fix trace_svc_register() call site
+    - drm/exynos: fix g2d_open/close helper function definitions
+    - net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
+    - virtio-net: Maintain reverse cleanup order
+    - virtio_net: Fix error unwinding of XDP initialization
+    - tipc: add tipc_bearer_min_mtu to calculate min mtu
+    - tipc: do not update mtu if msg_max is too small in mtu negotiation
+    - tipc: check the bearer min mtu properly when setting it by netlink
+    - s390/cio: include subchannels without devices also for evaluation
+    - net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()
+    - net: bcmgenet: Restore phy_stop() depending upon suspend/close
+    - wifi: mac80211: fix min center freq offset tracing
+    - wifi: iwlwifi: mvm: fix cancel_delayed_work_sync() deadlock
+    - wifi: iwlwifi: mvm: don't trust firmware n_channels
+    - scsi: storvsc: Don't pass unused PFNs to Hyper-V host
+    - cassini: Fix a memory leak in the error handling path of cas_init_one()
+    - net: dsa: mv88e6xxx: Fix mv88e6393x EPC write command offset
+    - igb: fix bit_shift to be in [1..8] range
+    - vlan: fix a potential uninit-value in vlan_dev_hard_start_xmit()
+    - netfilter: nf_tables: fix nft_trans type confusion
+    - netfilter: nft_set_rbtree: fix null deref on element insertion
+    - bridge: always declare tunnel functions
+    - ALSA: usb-audio: Add a sample rate workaround for Line6 Pod Go
+    - USB: usbtmc: Fix direction for 0-length ioctl control messages
+    - usb-storage: fix deadlock when a scsi command timeouts more than once
+    - USB: UHCI: adjust zhaoxin UHCI controllers OverCurrent bit value
+    - usb: dwc3: debugfs: Resume dwc3 before accessing registers
+    - usb: gadget: u_ether: Fix host MAC address case
+    - usb: typec: altmodes/displayport: fix pin_assignment_show
+    - xhci-pci: Only run d3cold avoidance quirk for s2idle
+    - xhci: Fix incorrect tracking of free space on transfer rings
+    - ALSA: hda: Fix Oops by 9.1 surround channel names
+    - ALSA: hda: Add NVIDIA codec IDs a3 through a7 to patch table
+    - ALSA: hda/realtek: Add quirk for Clevo L140AU
+    - ALSA: hda/realtek: Add a quirk for HP EliteDesk 805
+    - ALSA: hda/realtek: Add quirk for 2nd ASUS GU603
+    - can: j1939: recvmsg(): allow MSG_CMSG_COMPAT flag
+    - can: isotp: recvmsg(): allow MSG_CMSG_COMPAT flag
+    - can: kvaser_pciefd: Set CAN_STATE_STOPPED in kvaser_pciefd_stop()
+    - can: kvaser_pciefd: Call request_irq() before enabling interrupts
+    - can: kvaser_pciefd: Empty SRB buffer in probe
+    - can: kvaser_pciefd: Clear listen-only bit if not explicitly requested
+    - can: kvaser_pciefd: Do not send EFLUSH command on TFD interrupt
+    - can: kvaser_pciefd: Disable interrupts in probe error path
+    - SMB3: Close all deferred handles of inode in case of handle lease break
+    - SMB3: drop reference to cfile before sending oplock break
+    - ksmbd: smb2: Allow messages padded to 8byte boundary
+    - ksmbd: allocate one more byte for implied bcc[0]
+    - ksmbd: fix wrong UserName check in session_user
+    - ksmbd: fix global-out-of-bounds in smb2_find_context_vals
+    - statfs: enforce statfs[64] structure initialization
+    - serial: Add support for Advantech PCI-1611U card
+    - serial: 8250_exar: Add support for USR298x PCI Modems
+    - serial: qcom-geni: fix enabling deactivated interrupt
+    - thunderbolt: Clear registers properly when auto clear isn't in use
+    - vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF
+    - ceph: force updating the msg pointer in non-split case
+    - powerpc/iommu: Incorrect DDW Table is referenced for SR-IOV device
+    - tpm/tpm_tis: Disable interrupts for more Lenovo devices
+    - powerpc/64s/radix: Fix soft dirty tracking
+    - nilfs2: fix use-after-free bug of nilfs_root in nilfs_evict_inode()
+    - s390/qdio: fix do_sqbs() inline assembly constraint
+    - HID: wacom: Force pen out of prox if no events have been received in a while
+    - HID: wacom: Add new Intuos Pro Small (PTH-460) device IDs
+    - HID: wacom: add three styli to wacom_intuos_get_tool_type
+    - Linux 5.15.113
+  * Jammy update: v5.15.112 upstream stable release (LP: #2026607)
+    - ring-buffer: Ensure proper resetting of atomic variables in
+      ring_buffer_reset_online_cpus
+    - crypto: ccp - Clear PSP interrupt status register before calling handler
+    - ubifs: Fix AA deadlock when setting xattr for encrypted file
+    - ubifs: Fix memory leak in do_rename
+    - bus: mhi: Move host MHI code to "host" directory
+    - bus: mhi: host: Remove duplicate ee check for syserr
+    - bus: mhi: host: Use mhi_tryset_pm_state() for setting fw error state
+    - bus: mhi: host: Range check CHDBOFF and ERDBOFF
+    - mailbox: zynq: Switch to flexible array to simplify code
+    - mailbox: zynqmp: Fix counts of child nodes
+    - ASoC: soc-pcm: use GFP_ATOMIC for dpcm structure
+    - ASoC: soc-pcm: align BE 'atomicity' with that of the FE
+    - ASoC: soc-pcm: Fix and cleanup DPCM locking
+    - ASoC: soc-pcm: serialize BE triggers
+    - ASoC: soc-pcm: test refcount before triggering
+    - ASoC: soc-pcm: fix BE handling of PAUSE_RELEASE
+    - fs/ntfs3: Fix null-ptr-deref on inode->i_op in ntfs_lookup()
+    - drm/hyperv: Don't overwrite dirt_needed value set by host
+    - scsi: qedi: Fix use after free bug in qedi_remove()
+    - net/ncsi: clear Tx enable mode when handling a Config required AEN
+    - net/sched: cls_api: remove block_cb from driver_list before freeing
+    - sit: update dev->needed_headroom in ipip6_tunnel_bind_dev()
+    - selftests: srv6: make srv6_end_dt46_l3vpn_test more robust
+    - net: dsa: mv88e6xxx: add mv88e6321 rsvd2cpu
+    - writeback: fix call of incorrect macro
+    - watchdog: dw_wdt: Fix the error handling path of dw_wdt_drv_probe()
+    - RISC-V: mm: Enable huge page support to kernel_page_present() function
+    - net/sched: act_mirred: Add carrier check
+    - r8152: fix flow control issue of RTL8156A
+    - r8152: fix the poor throughput for 2.5G devices
+    - r8152: move setting r8153b_rx_agg_chg_indicate()
+    - sfc: Fix module EEPROM reporting for QSFP modules
+    - rxrpc: Fix hard call timeout units
+    - octeontx2-af: Secure APR table update with the lock
+    - octeontx2-af: Skip PFs if not enabled
+    - octeontx2-pf: Disable packet I/O for graceful exit
+    - octeontx2-vf: Detach LF resources on probe cleanup
+    - ionic: remove noise from ethtool rxnfc error msg
+    - ethtool: Fix uninitialized number of lanes
+    - ionic: catch failure from devlink_alloc
+    - af_packet: Don't send zero-byte data in packet_sendmsg_spkt().
+    - drm/amdgpu: add a missing lock for AMDGPU_SCHED
+    - ALSA: caiaq: input: Add error handling for unsupported input methods in
+      `snd_usb_caiaq_input_init`
+    - net: dsa: mt7530: fix corrupt frames using trgmii on 40 MHz XTAL MT7621
+    - virtio_net: split free_unused_bufs()
+    - virtio_net: suppress cpu stall when free_unused_bufs
+    - net: enetc: check the index of the SFI rather than the handle
+    - perf scripts intel-pt-events.py: Fix IPC output for Python 2
+    - perf vendor events power9: Remove UTF-8 characters from JSON files
+    - perf pmu: zfree() expects a pointer to a pointer to zero it after freeing
+      its contents
+    - perf map: Delete two variable initialisations before null pointer checks in
+      sort__sym_from_cmp()
+    - crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
+    - crypto: engine - check if BH is disabled during completion
+    - crypto: api - Add scaffolding to change completion function signature
+    - crypto: engine - Use crypto_request_complete
+    - crypto: engine - fix crypto_queue backlog handling
+    - perf symbols: Fix return incorrect build_id size in elf_read_build_id()
+    - perf evlist: Refactor evlist__for_each_cpu()
+    - perf stat: Separate bperf from bpf_profiler
+    - btrfs: fix btrfs_prev_leaf() to not return the same key twice
+    - btrfs: zoned: fix wrong use of bitops API in btrfs_ensure_empty_zones
+    - btrfs: fix encoded write i_size corruption with no-holes
+    - btrfs: don't free qgroup space unless specified
+    - btrfs: zero the buffer before marking it dirty in btrfs_redirty_list_add
+    - btrfs: print-tree: parent bytenr must be aligned to sector size
+    - btrfs: fix space cache inconsistency after error loading it from disk
+    - cifs: fix pcchunk length type in smb2_copychunk_range
+    - cifs: release leases for deferred close handles when freezing
+    - platform/x86: touchscreen_dmi: Add upside-down quirk for GDIX1002 ts on the
+      Juno Tablet
+    - platform/x86: touchscreen_dmi: Add info for the Dexp Ursus KX210i
+    - inotify: Avoid reporting event with invalid wd
+    - smb3: fix problem remounting a share after shutdown
+    - SMB3: force unmount was failing to close deferred close files
+    - sh: math-emu: fix macro redefined warning
+    - sh: mcount.S: fix build error when PRINTK is not enabled
+    - sh: init: use OF_EARLY_FLATTREE for early init
+    - sh: nmi_debug: fix return value of __setup handler
+    - remoteproc: stm32: Call of_node_put() on iteration error
+    - remoteproc: st: Call of_node_put() on iteration error
+    - remoteproc: imx_rproc: Call of_node_put() on iteration error
+    - ARM: dts: exynos: fix WM8960 clock name in Itop Elite
+    - ARM: dts: s5pv210: correct MIPI CSIS clock name
+    - drm/bridge: lt8912b: Fix DSI Video Mode
+    - drm/msm: fix NULL-deref on snapshot tear down
+    - drm/msm: fix NULL-deref on irq uninstall
+    - f2fs: fix potential corruption when moving a directory
+    - drm/panel: otm8009a: Set backlight parent to panel device
+    - drm/amd/display: fix flickering caused by S/G mode
+    - drm/amdgpu: fix an amdgpu_irq_put() issue in gmc_v9_0_hw_fini()
+    - drm/amdgpu/gfx: disable gfx9 cp_ecc_error_irq only when enabling legacy gfx
+      ras
+    - drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)
+    - drm/amdgpu: disable sdma ecc irq only when sdma RAS is enabled in suspend
+    - HID: wacom: Set a default resolution for older tablets
+    - HID: wacom: insert timestamp to packed Bluetooth (BT) events
+    - fs/ntfs3: Refactoring of various minor issues
+    - ASoC: soc-pcm: Fix DPCM lockdep warning due to nested stream locks
+    - ASoC: soc-compress: Inherit atomicity from DAI link for Compress FE
+    - ASoC: soc-pcm: Move debugfs removal out of spinlock
+    - ASoC: DPCM: Don't pick up BE without substream
+    - ASoC: soc-pcm.c: call __soc_pcm_close() in soc_pcm_close()
+    - drm/i915/dg2: Support 4k@30 on HDMI
+    - drm/i915/dg2: Add additional HDMI pixel clock frequencies
+    - drm/i915/dg2: Add HDMI pixel clock frequencies 267.30 and 319.89 MHz
+    - drm/msm: Remove struct_mutex usage
+    - drm/msm/adreno: fix runtime PM imbalance at gpu load
+    - drm/amd/display: Refine condition of cursor visibility for pipe-split
+    - drm/amd/display: Add NULL plane_state check for cursor disable logic
+    - wifi: rtw88: rtw8821c: Fix rfe_option field width
+    - ksmbd: set RSS capable in FSCTL_QUERY_NETWORK_INTERFACE_INFO
+    - ksmbd: fix multi session connection failure
+    - ksmbd: replace sessions list in connection with xarray
+    - ksmbd: add channel rwlock
+    - ksmbd: fix kernel oops from idr_remove()
+    - ksmbd: fix racy issue while destroying session on multichannel
+    - ksmbd: fix deadlock in ksmbd_find_crypto_ctx()
+    - ksmbd: not allow guest user on multichannel
+    - locking/rwsem: Add __always_inline annotation to __down_read_common() and
+      inlined callers
+    - ext4: fix WARNING in mb_find_extent
+    - ext4: avoid a potential slab-out-of-bounds in ext4_group_desc_csum
+    - ext4: fix data races when using cached status extents
+    - ext4: check iomap type only if ext4_iomap_begin() does not fail
+    - ext4: improve error recovery code paths in __ext4_remount()
+    - ext4: improve error handling from ext4_dirhash()
+    - ext4: fix deadlock when converting an inline directory in nojournal mode
+    - ext4: add bounds checking in get_max_inline_xattr_value_size()
+    - ext4: bail out of ext4_xattr_ibody_get() fails for any reason
+    - ext4: remove a BUG_ON in ext4_mb_release_group_pa()
+    - ext4: fix invalid free tracking in ext4_xattr_move_to_block()
+    - drm/msm/adreno: adreno_gpu: Use suspend() instead of idle() on load error
+    - serial: 8250: Fix serial8250_tx_empty() race with DMA Tx
+    - drbd: correctly submit flush bio on barrier
+    - RISC-V: Fix up a cherry-pick warning in setup_vm_final()
+    - drm/amd/display: Fix hang when skipping modeset
+    - Linux 5.15.112
+  * CVE-2023-31084 // CVE-2023-31084 was assigned to this bug.
+    - media: dvb-core: Fix kernel WARNING for blocking operation in wait_event*()
+  * CVE-2023-3776
+    - net/sched: cls_fw: Fix improper refcount update leads to use-after-free
+
+  [ Ubuntu: 5.15.0-79.86 ]
+
+  * jammy/linux: 5.15.0-79.86 -proposed tracker (LP: #2026531)
+  * Jammy update: v5.15.111 upstream stable release (LP: #2025095)
+    - ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15
+    - ASoC: soc-pcm: fix hw->formats cleared by soc_pcm_hw_init() for dpcm
+    - x86/hyperv: Block root partition functionality in a Confidential VM
+    - iio: adc: palmas_gpadc: fix NULL dereference on rmmod
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Acer Iconia One 7 B1-750
+    - selftests mount: Fix mount_setattr_test builds failed
+    - asm-generic/io.h: suppress endianness warnings for readq() and writeq()
+    - x86/cpu: Add model number for Intel Arrow Lake processor
+    - wireguard: timers: cast enum limits members to int in prints
+    - wifi: mt76: mt7921e: Set memory space enable in PCI_COMMAND if unset
+    - arm64: Always load shadow stack pointer directly from the task struct
+    - arm64: Stash shadow stack pointer in the task struct on interrupt
+    - PCI: pciehp: Fix AB-BA deadlock between reset_lock and device_lock
+    - PCI: qcom: Fix the incorrect register usage in v2.7.0 config
+    - IMA: allow/fix UML builds
+    - USB: dwc3: fix runtime pm imbalance on probe errors
+    - USB: dwc3: fix runtime pm imbalance on unbind
+    - hwmon: (k10temp) Check range scale when CUR_TEMP register is read-write
+    - hwmon: (adt7475) Use device_property APIs when configuring polarity
+    - posix-cpu-timers: Implement the missing timer_wait_running callback
+    - blk-mq: release crypto keyslot before reporting I/O complete
+    - blk-crypto: make blk_crypto_evict_key() return void
+    - blk-crypto: make blk_crypto_evict_key() more robust
+    - ext4: use ext4_journal_start/stop for fast commit transactions
+    - staging: iio: resolver: ads1210: fix config mode
+    - tty: Prevent writing chars during tcsetattr TCSADRAIN/FLUSH
+    - xhci: fix debugfs register accesses while suspended
+    - tick/nohz: Fix cpu_is_hotpluggable() by checking with nohz subsystem
+    - MIPS: fw: Allow firmware to pass a empty env
+    - ipmi:ssif: Add send_retries increment
+    - ipmi: fix SSIF not responding under certain cond.
+    - kheaders: Use array declaration instead of char
+    - wifi: mt76: add missing locking to protect against concurrent rx/status
+      calls
+    - pwm: meson: Fix axg ao mux parents
+    - pwm: meson: Fix g12a ao clk81 name
+    - soundwire: qcom: correct setting ignore bit on v1.5.1
+    - pinctrl: qcom: lpass-lpi: set output value before enabling output
+    - ring-buffer: Sync IRQ works before buffer destruction
+    - crypto: api - Demote BUG_ON() in crypto_unregister_alg() to a WARN_ON()
+    - crypto: safexcel - Cleanup ring IRQ workqueues on load failure
+    - rcu: Avoid stack overflow due to __rcu_irq_enter_check_tick() being kprobe-
+      ed
+    - reiserfs: Add security prefix to xattr name in reiserfs_security_write()
+    - KVM: nVMX: Emulate NOPs in L2, and PAUSE if it's not intercepted
+    - relayfs: fix out-of-bounds access in relay_file_read
+    - writeback, cgroup: fix null-ptr-deref write in bdi_split_work_to_wbs
+    - ksmbd: call rcu_barrier() in ksmbd_server_exit()
+    - ksmbd: fix NULL pointer dereference in smb2_get_info_filesystem()
+    - ksmbd: fix memleak in session setup
+    - i2c: omap: Fix standard mode false ACK readings
+    - riscv: mm: remove redundant parameter of create_fdt_early_page_table
+    - tracing: Fix permissions for the buffer_percent file
+    - iommu/amd: Fix "Guest Virtual APIC Table Root Pointer" configuration in IRTE
+    - ubifs: Fix memleak when insert_old_idx() failed
+    - ubi: Fix return value overwrite issue in try_write_vid_and_data()
+    - ubifs: Free memory for tmpfile name
+    - xfs: don't consider future format versions valid
+    - sound/oss/dmasound: fix build when drivers are mixed =y/=m
+    - rcu: Fix missing TICK_DEP_MASK_RCU_EXP dependency check
+    - selftests/resctrl: Return NULL if malloc_and_init_memory() did not alloc mem
+    - selftests/resctrl: Extend CPU vendor detection
+    - selftests/resctrl: Move ->setup() call outside of test specific branches
+    - selftests/resctrl: Allow ->setup() to return errors
+    - selftests/resctrl: Check for return value after write_schemata()
+    - selinux: fix Makefile dependencies of flask.h
+    - selinux: ensure av_permissions.h is built when needed
+    - tpm, tpm_tis: Do not skip reset of original interrupt vector
+    - tpm, tpm_tis: Claim locality before writing TPM_INT_ENABLE register
+    - tpm, tpm_tis: Disable interrupts if tpm_tis_probe_irq() failed
+    - tpm, tpm_tis: Claim locality before writing interrupt registers
+    - tpm, tpm: Implement usage counter for locality
+    - tpm, tpm_tis: Claim locality when interrupts are reenabled on resume
+    - erofs: stop parsing non-compact HEAD index if clusterofs is invalid
+    - erofs: fix potential overflow calculating xattr_isize
+    - drm/rockchip: Drop unbalanced obj unref
+    - drm/vgem: add missing mutex_destroy
+    - drm/probe-helper: Cancel previous job before starting new one
+    - tools/x86/kcpuid: Fix avx512bw and avx512lvl fields in Fn00000007
+    - soc: ti: pm33xx: Fix refcount leak in am33xx_pm_probe
+    - arm64: dts: renesas: r8a77990: Remove bogus voltages from OPP table
+    - arm64: dts: renesas: r8a774c0: Remove bogus voltages from OPP table
+    - drm/msm/disp/dpu: check for crtc enable rather than crtc active to release
+      shared resources
+    - EDAC/skx: Fix overflows on the DRAM row address mapping arrays
+    - regulator: core: Shorten off-on-delay-us for always-on/boot-on by time since
+      booted
+    - arm64: dts: ti: k3-j721e-main: Remove ti,strobe-sel property
+    - arm64: dts: broadcom: bcm4908: add DT for Netgear RAXE500
+    - arm64: dts: Add DTS files for bcmbca SoC BCM63158
+    - arm64: dts: Add DTS files for bcmbca SoC BCM4912
+    - ARM64: dts: Add DTS files for bcmbca SoC BCM6858
+    - arm64: dts: Add base DTS file for bcmbca device Asus GT-AX6000
+    - arm64: dts: Move BCM4908 dts to bcmbca folder
+    - arm64: dts: broadcom: bcmbca: bcm4908: fix NAND interrupt name
+    - arm64: dts: broadcom: bcmbca: bcm4908: fix procmon nodename
+    - arm64: dts: qcom: msm8998: Fix stm-stimulus-base reg name
+    - arm64: dts: qcom: sdm845: correct dynamic power coefficients
+    - arm64: dts: qcom: sdm845: Fix the PCI I/O port range
+    - arm64: dts: qcom: msm8998: Fix the PCI I/O port range
+    - arm64: dts: qcom: ipq8074: Fix the PCI I/O port range
+    - arm64: dts: qcom: ipq6018: Fix the PCI I/O port range
+    - arm64: dts: qcom: msm8996: Fix the PCI I/O port range
+    - arm64: dts: qcom: sm8250: Fix the PCI I/O port range
+    - ARM: dts: qcom: ipq4019: Fix the PCI I/O port range
+    - ARM: dts: qcom: ipq8064: reduce pci IO size to 64K
+    - ARM: dts: qcom: ipq8064: Fix the PCI I/O port range
+    - x86/MCE/AMD: Use an u64 for bank_map
+    - media: bdisp: Add missing check for create_workqueue
+    - media: av7110: prevent underflow in write_ts_to_decoder()
+    - firmware: qcom_scm: Clear download bit during reboot
+    - drm/bridge: adv7533: Fix adv7533_mode_valid for adv7533 and adv7535
+    - media: max9286: Free control handler
+    - drm/msm/adreno: Defer enabling runpm until hw_init()
+    - drm/msm/adreno: drop bogus pm_runtime_set_active()
+    - drm: msm: adreno: Disable preemption on Adreno 510
+    - drm/amd/display/dc/dce60/Makefile: Fix previous attempt to silence known
+      override-init warnings
+    - ACPI: processor: Fix evaluating _PDC method when running as Xen dom0
+    - mmc: sdhci-of-esdhc: fix quirk to ignore command inhibit for data
+    - drm: rcar-du: Fix a NULL vs IS_ERR() bug
+    - ARM: dts: gta04: fix excess dma channel usage
+    - firmware: arm_scmi: Fix xfers allocation on Rx channel
+    - ACPI: VIOT: Initialize the correct IOMMU fwspec
+    - drm/lima/lima_drv: Add missing unwind goto in lima_pdev_probe()
+    - mailbox: mpfs: switch to txdone_poll
+    - arm64: dts: qcom: sc7180-trogdor-lazor: correct trackpad supply
+    - arm64: dts: qcom: msm8994-kitakami: drop unit address from PMI8994 regulator
+    - arm64: dts: qcom: msm8994-msft-lumia-octagon: drop unit address from PMI8994
+      regulator
+    - drm/ttm: optimize pool allocations a bit v2
+    - drm/ttm/pool: Fix ttm_pool_alloc error path
+    - regulator: core: Consistently set mutex_owner when using
+      ww_mutex_lock_slow()
+    - regulator: core: Avoid lockdep reports when resolving supplies
+    - x86/apic: Fix atomic update of offset in reserve_eilvt_offset()
+    - media: rkvdec: fix use after free bug in rkvdec_remove
+    - media: dm1105: Fix use after free bug in dm1105_remove due to race condition
+    - media: saa7134: fix use after free bug in saa7134_finidev due to race
+      condition
+    - media: rcar_fdp1: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - media: rcar_fdp1: Fix the correct variable assignments
+    - platform: Provide a remove callback that returns no value
+    - media: rcar_fdp1: Convert to platform remove callback returning void
+    - media: rcar_fdp1: Fix refcount leak in probe and remove function
+    - drm/amd/display: Fix potential null dereference
+    - media: rc: gpio-ir-recv: Fix support for wake-up
+    - media: venus: dec: Fix handling of the start cmd
+    - regulator: stm32-pwr: fix of_iomap leak
+    - x86/ioapic: Don't return 0 from arch_dynirq_lower_bound()
+    - arm64: kgdb: Set PSTATE.SS to 1 to re-enable single-step
+    - debugobject: Prevent init race with static objects
+    - drm/i915: Make intel_get_crtc_new_encoder() less oopsy
+    - tick/common: Align tick period with the HZ tick.
+    - cpufreq: use correct unit when verify cur freq
+    - hwmon: (pmbus/fsp-3y) Fix functionality bitmask in FSP-3Y YM-2151E
+    - wifi: ath6kl: minor fix for allocation size
+    - wifi: ath9k: hif_usb: fix memory leak of remain_skbs
+    - wifi: ath5k: fix an off by one check in ath5k_eeprom_read_freq_list()
+    - wifi: brcmfmac: support CQM RSSI notification with older firmware
+    - wifi: ath6kl: reduce WARN to dev_dbg() in callback
+    - tools: bpftool: Remove invalid \' json escape
+    - wifi: rtw88: mac: Return the original error from rtw_pwr_seq_parser()
+    - wifi: rtw88: mac: Return the original error from rtw_mac_power_switch()
+    - bpf: take into account liveness when propagating precision
+    - bpf: fix precision propagation verbose logging
+    - scm: fix MSG_CTRUNC setting condition for SO_PASSSEC
+    - selftests/bpf: Fix a fd leak in an error path in network_helpers.c
+    - bpf: Remove misleading spec_v1 check on var-offset stack read
+    - net: pcs: xpcs: remove double-read of link state when using AN
+    - vlan: partially enable SIOCSHWTSTAMP in container
+    - net/packet: annotate accesses to po->xmit
+    - net/packet: convert po->origdev to an atomic flag
+    - net/packet: convert po->auxdata to an atomic flag
+    - scsi: target: Fix multiple LUN_RESET handling
+    - scsi: target: iscsit: Fix TAS handling during conn cleanup
+    - scsi: megaraid: Fix mega_cmd_done() CMDID_INT_CMDS
+    - f2fs: handle dqget error in f2fs_transfer_project_quota()
+    - f2fs: enforce single zone capacity
+    - f2fs: apply zone capacity to all zone type
+    - f2fs: compress: fix to call f2fs_wait_on_page_writeback() in
+      f2fs_write_raw_pages()
+    - crypto: caam - Clear some memory in instantiate_rng
+    - crypto: sa2ul - Select CRYPTO_DES
+    - wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_rfreg()
+    - wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_reg()
+    - wifi: rt2x00: Fix memory leak when handling surveys
+    - net: qrtr: correct types of trace event parameters
+    - selftests: xsk: Disable IPv6 on VETH1
+    - selftests/bpf: Wait for receive in cg_storage_multi test
+    - bpftool: Fix bug for long instructions in program CFG dumps
+    - crypto: drbg - make drbg_prepare_hrng() handle jent instantiation errors
+    - crypto: drbg - Only fail when jent is unavailable in FIPS mode
+    - xsk: Fix unaligned descriptor validation
+    - f2fs: fix to avoid use-after-free for cached IPU bio
+    - scsi: lpfc: Fix ioremap issues in lpfc_sli4_pci_mem_setup()
+    - net: ethernet: stmmac: dwmac-rk: fix optional phy regulator handling
+    - bpf, sockmap: fix deadlocks in the sockhash and sockmap
+    - nvmet: use i_size_read() to set size for file-ns
+    - nvmet: move the call to nvmet_ns_changed out of nvmet_ns_revalidate
+    - nvmet: fix error handling in nvmet_execute_identify_cns_cs_ns()
+    - nvmet: fix Identify Namespace handling
+    - nvmet: fix Identify Controller handling
+    - nvmet: fix Identify Active Namespace ID list handling
+    - nvmet: fix I/O Command Set specific Identify Controller
+    - nvme: handle the persistent internal error AER
+    - nvme: fix async event trace event
+    - nvme-fcloop: fix "inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage"
+    - selftests/bpf: Fix leaked bpf_link in get_stackid_cannot_attach
+    - bpf, sockmap: Revert buggy deadlock fix in the sockhash and sockmap
+    - md: drop queue limitation for RAID1 and RAID10
+    - md: raid10 add nowait support
+    - md/raid10: factor out code from wait_barrier() to stop_waiting_barrier()
+    - md/raid10: fix task hung in raid10d
+    - md/raid10: fix leak of 'r10bio->remaining' for recovery
+    - md/raid10: fix memleak for 'conf->bio_split'
+    - md/raid10: fix memleak of md thread
+    - md/raid10: don't call bio_start_io_acct twice for bio which experienced read
+      error
+    - wifi: iwlwifi: yoyo: skip dump correctly on hw error
+    - wifi: iwlwifi: yoyo: Fix possible division by zero
+    - wifi: iwlwifi: mvm: initialize seq variable
+    - wifi: iwlwifi: fw: move memset before early return
+    - jdb2: Don't refuse invalidation of already invalidated buffers
+    - wifi: iwlwifi: make the loop for card preparation effective
+    - wifi: mt76: handle failure of vzalloc in mt7615_coredump_work
+    - wifi: mt76: add flexible polling wait-interval support
+    - wifi: mt76: mt7921e: fix probe timeout after reboot
+    - wifi: mt76: fix 6GHz high channel not be scanned
+    - wifi: mt76: mt7921e: improve reliability of dma reset
+    - wifi: iwlwifi: mvm: check firmware response size
+    - wifi: iwlwifi: fw: fix memory leak in debugfs
+    - ixgbe: Allow flow hash to be set via ethtool
+    - ixgbe: Enable setting RSS table to default values
+    - net/mlx5: E-switch, Don't destroy indirect table in split rule
+    - net: stmmac:fix system hang when setting up tag_8021q VLAN for DSA ports
+    - bpf: Don't EFAULT for getsockopt with optval=NULL
+    - netfilter: nf_tables: don't write table validation state without mutex
+    - net/sched: sch_fq: fix integer overflow of "credit"
+    - ipv4: Fix potential uninit variable access bug in __ip_make_skb()
+    - netlink: Use copy_to_user() for optval in netlink_getsockopt().
+    - net: amd: Fix link leak when verifying config failed
+    - tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
+    - ipmi: ASPEED_BT_IPMI_BMC: select REGMAP_MMIO instead of depending on it
+    - drivers: staging: rtl8723bs: Fix locking in _rtw_join_timeout_handler()
+    - drivers: staging: rtl8723bs: Fix locking in rtw_scan_timeout_handler()
+    - pstore: Revert pmsg_lock back to a normal mutex
+    - usb: host: xhci-rcar: remove leftover quirk handling
+    - usb: dwc3: gadget: Change condition for processing suspend event
+    - serial: stm32: re-introduce an irq flag condition in usart_receive_chars
+    - serial: stm32: Re-assert RTS/DE GPIO in RS485 mode only if more data are
+      transmitted
+    - fpga: bridge: fix kernel-doc parameter description
+    - iio: light: max44009: add missing OF device matching
+    - serial: 8250_bcm7271: Fix arbitration handling
+    - spi: spi-imx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
+    - spi: imx: Don't skip cleanup in remove's error path
+    - usb: gadget: udc: renesas_usb3: Fix use after free bug in
+      renesas_usb3_remove due to race condition
+    - PCI: imx6: Install the fault handler only on compatible match
+    - ASoC: es8316: Handle optional IRQ assignment
+    - linux/vt_buffer.h: allow either builtin or modular for macros
+    - spi: qup: Don't skip cleanup in remove's error path
+    - spi: fsl-spi: Fix CPM/QE mode Litte Endian
+    - vmci_host: fix a race condition in vmci_host_poll() causing GPF
+    - of: Fix modalias string generation
+    - PCI/EDR: Clear Device Status after EDR error recovery
+    - ia64: mm/contig: fix section mismatch warning/error
+    - ia64: salinfo: placate defined-but-not-used warning
+    - scripts/gdb: bail early if there are no clocks
+    - scripts/gdb: bail early if there are no generic PD
+    - HID: amd_sfh: Add support for shutdown operation
+    - coresight: etm_pmu: Set the module field
+    - ASoC: fsl_mqs: move of_node_put() to the correct location
+    - spi: cadence-quadspi: fix suspend-resume implementations
+    - i2c: cadence: cdns_i2c_master_xfer(): Fix runtime PM leak on error path
+    - scripts/gdb: raise error with reduced debugging information
+    - uapi/linux/const.h: prefer ISO-friendly __typeof__
+    - sh: sq: Fix incorrect element size for allocating bitmap buffer
+    - usb: gadget: tegra-xudc: Fix crash in vbus_draw
+    - usb: chipidea: fix missing goto in `ci_hdrc_probe`
+    - usb: mtu3: fix kernel panic at qmu transfer done irq handler
+    - firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe
+    - tty: serial: fsl_lpuart: adjust buffer length to the intended size
+    - serial: 8250: Add missing wakeup event reporting
+    - staging: rtl8192e: Fix W_DISABLE# does not work after stop/start
+    - spmi: Add a check for remove callback when removing a SPMI driver
+    - virtio_ring: don't update event idx on get_buf
+    - macintosh/windfarm_smu_sat: Add missing of_node_put()
+    - powerpc/mpc512x: fix resource printk format warning
+    - powerpc/wii: fix resource printk format warnings
+    - powerpc/sysdev/tsi108: fix resource printk format warnings
+    - macintosh: via-pmu-led: requires ATA to be set
+    - powerpc/rtas: use memmove for potentially overlapping buffer copy
+    - sched/fair: Use __schedstat_set() in set_next_entity()
+    - sched: Make struct sched_statistics independent of fair sched class
+    - sched/fair: Fix inaccurate tally of ttwu_move_affine
+    - perf/core: Fix hardlockup failure caused by perf throttle
+    - Revert "objtool: Support addition to set CFA base"
+    - sched/rt: Fix bad task migration for rt tasks
+    - clk: at91: clk-sam9x60-pll: fix return value check
+    - RDMA/siw: Fix potential page_array out of range access
+    - RDMA/rdmavt: Delete unnecessary NULL check
+    - workqueue: Introduce show_one_worker_pool and show_one_workqueue.
+    - workqueue: Fix hung time report of worker pools
+    - rtc: omap: include header for omap_rtc_power_off_program prototype
+    - RDMA/mlx4: Prevent shift wrapping in set_user_sq_size()
+    - rtc: meson-vrtc: Use ktime_get_real_ts64() to get the current time
+    - fs/ntfs3: Fix memory leak if ntfs_read_mft failed
+    - fs/ntfs3: Add check for kmemdup
+    - fs/ntfs3: Fix OOB read in indx_insert_into_buffer
+    - fs/ntfs3: Fix slab-out-of-bounds read in hdr_delete_de()
+    - power: supply: generic-adc-battery: fix unit scaling
+    - clk: add missing of_node_put() in "assigned-clocks" property parsing
+    - RDMA/siw: Remove namespace check from siw_netdev_event()
+    - clk: qcom: gcc-sm6115: Mark RCGs shared where applicable
+    - RDMA/cm: Trace icm_send_rej event before the cm state is reset
+    - RDMA/srpt: Add a check for valid 'mad_agent' pointer
+    - IB/hfi1: Fix SDMA mmu_rb_node not being evicted in LRU order
+    - IB/hfi1: Fix bugs with non-PAGE_SIZE-end multi-iovec user SDMA requests
+    - NFSv4.1: Always send a RECLAIM_COMPLETE after establishing lease
+    - clk: qcom: regmap: add PHY clock source implementation
+    - clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
+    - Input: raspberrypi-ts - fix refcount leak in rpi_ts_probe
+    - RDMA/mlx5: Fix flow counter query via DEVX
+    - SUNRPC: remove the maximum number of retries in call_bind_status
+    - RDMA/mlx5: Use correct device num_ports when modify DC
+    - clocksource/drivers/davinci: Fix memory leak in davinci_timer_register when
+      init fails
+    - openrisc: Properly store r31 to pt_regs on unhandled exceptions
+    - timekeeping: Fix references to nonexistent ktime_get_fast_ns()
+    - SMB3: Add missing locks to protect deferred close file list
+    - SMB3: Close deferred file handles in case of handle lease break
+    - ext4: fix i_disksize exceeding i_size problem in paritally written case
+    - ext4: fix use-after-free read in ext4_find_extent for bigalloc + inline
+    - pinctrl: renesas: r8a779a0: Remove incorrect AVB[01] pinmux configuration
+    - leds: TI_LMU_COMMON: select REGMAP instead of depending on it
+    - dmaengine: mv_xor_v2: Fix an error code.
+    - leds: tca6507: Fix error handling of using fwnode_property_read_string
+    - pwm: mtk-disp: Disable shadow registers before setting backlight values
+    - pwm: mtk-disp: Configure double buffering before reading in .get_state()
+    - phy: tegra: xusb: Add missing tegra_xusb_port_unregister for usb2_port and
+      ulpi_port
+    - dma: gpi: remove spurious unlock in gpi_ch_init
+    - dmaengine: dw-edma: Fix to change for continuous transfer
+    - dmaengine: dw-edma: Fix to enable to issue dma request on DMA processing
+    - dmaengine: at_xdmac: Fix concurrency over chan's completed_cookie
+    - dmaengine: at_xdmac: Fix race for the tx desc callback
+    - dmaengine: at_xdmac: do not enable all cyclic channels
+    - thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in
+      mtk_thermal_probe
+    - mfd: tqmx86: Do not access I2C_DETECT register through io_base
+    - mfd: tqmx86: Specify IO port register range more precisely
+    - mfd: tqmx86: Correct board names for TQMxE39x
+    - afs: Fix updating of i_size with dv jump from server
+    - parisc: Fix argument pointer in real64_call_asm()
+    - ALSA: usb-audio: Add quirk for Pioneer DDJ-800
+    - nilfs2: do not write dirty data after degenerating to read-only
+    - nilfs2: fix infinite loop in nilfs_mdt_get_block()
+    - md/raid10: fix null-ptr-deref in raid10_sync_request
+    - mtd: core: provide unique name for nvmem device, take two
+    - mtd: core: fix nvmem error reporting
+    - mtd: core: fix error path for nvmem provider
+    - mailbox: zynqmp: Fix IPI isr handling
+    - mailbox: zynqmp: Fix typo in IPI documentation
+    - wifi: rtl8xxxu: RTL8192EU always needs full init
+    - clk: rockchip: rk3399: allow clk_cifout to force clk_cifout_src to reparent
+    - scripts/gdb: fix lx-timerlist for Python3
+    - btrfs: scrub: reject unsupported scrub flags
+    - s390/dasd: fix hanging blockdevice after request requeue
+    - ia64: fix an addr to taddr in huge_pte_offset()
+    - dm verity: fix error handling for check_at_most_once on FEC
+    - dm clone: call kmem_cache_destroy() in dm_clone_init() error path
+    - dm integrity: call kmem_cache_destroy() in dm_integrity_init() error path
+    - dm flakey: fix a crash with invalid table line
+    - dm ioctl: fix nested locking in table_clear() to remove deadlock concern
+    - dm: don't lock fs when the map is NULL in process of resume
+    - perf auxtrace: Fix address filter entire kernel size
+    - perf intel-pt: Fix CYC timestamps after standalone CBR
+    - sound/oss/dmasound: fix 'dmasound_setup' defined but not used
+    - arm64: dts: qcom: sdm845: correct dynamic power coefficients - again
+    - sched: Fix DEBUG && !SCHEDSTATS warn
+    - Linux 5.15.111
+  * Jammy update: v5.15.110 upstream stable release (LP: #2025090)
+    - PCI/ASPM: Remove pcie_aspm_pm_state_change()
+    - selftests/kselftest/runner/run_one(): allow running non-executable files
+    - KVM: arm64: Retry fault if vma_lookup() results become invalid
+    - KVM: arm64: Fix buffer overflow in kvm_arm_set_fw_reg()
+    - drm/fb-helper: set x/yres_virtual in drm_fb_helper_check_var
+    - bluetooth: Perform careful capability checks in hci_sock_ioctl()
+    - USB: serial: option: add UNISOC vendor and TOZED LT70C product
+    - driver core: Don't require dynamic_debug for initcall_debug probe timing
+    - selftests: mptcp: join: fix "invalid address, ADD_ADDR timeout"
+    - riscv: Move early dtb mapping into the fixmap region
+    - riscv: Do not set initial_boot_params to the linear address of the dtb
+    - riscv: No need to relocate the dtb as it lies in the fixmap region
+    - Linux 5.15.110
+  * Jammy update: v5.15.109 upstream stable release (LP: #2024265)
+    - ARM: dts: rockchip: fix a typo error for rk3288 spdif node
+    - arm64: dts: qcom: ipq8074-hk01: enable QMP device, not the PHY node
+    - arm64: dts: meson-g12-common: specify full DMC range
+    - arm64: dts: imx8mm-evk: correct pmic clock source
+    - netfilter: br_netfilter: fix recent physdev match breakage
+    - regulator: fan53555: Explicitly include bits header
+    - regulator: fan53555: Fix wrong TCS_SLEW_MASK
+    - virtio_net: bugfix overflow inside xdp_linearize_page()
+    - sfc: Split STATE_READY in to STATE_NET_DOWN and STATE_NET_UP.
+    - sfc: Fix use-after-free due to selftest_work
+    - netfilter: nf_tables: fix ifdef to also consider nf_tables=m
+    - i40e: fix accessing vsi->active_filters without holding lock
+    - i40e: fix i40e_setup_misc_vector() error handling
+    - netfilter: nf_tables: validate catch-all set elements
+    - netfilter: nf_tables: tighten netlink attribute requirements for catch-all
+      elements
+    - bnxt_en: Do not initialize PTP on older P3/P4 chips
+    - mlxfw: fix null-ptr-deref in mlxfw_mfa2_tlv_next()
+    - bonding: Fix memory leak when changing bond type to Ethernet
+    - net: rpl: fix rpl header size calculation
+    - mlxsw: pci: Fix possible crash during initialization
+    - spi: spi-rockchip: Fix missing unwind goto in rockchip_sfc_probe()
+    - bpf: Fix incorrect verifier pruning due to missing register precision taints
+    - e1000e: Disable TSO on i219-LM card to increase speed
+    - f2fs: Fix f2fs_truncate_partial_nodes ftrace event
+    - Input: i8042 - add quirk for Fujitsu Lifebook A574/H
+    - platform/x86 (gigabyte-wmi): Add support for A320M-S2H V2
+    - selftests: sigaltstack: fix -Wuninitialized
+    - scsi: megaraid_sas: Fix fw_crash_buffer_show()
+    - scsi: core: Improve scsi_vpd_inquiry() checks
+    - net: dsa: b53: mmap: add phy ops
+    - s390/ptrace: fix PTRACE_GET_LAST_BREAK error handling
+    - nvme-tcp: fix a possible UAF when failing to allocate an io queue
+    - xen/netback: use same error messages for same errors
+    - platform/x86: gigabyte-wmi: add support for X570S AORUS ELITE
+    - rtmutex: Add acquire semantics for rtmutex lock acquisition slow path
+    - iio: light: tsl2772: fix reading proximity-diodes from device tree
+    - nilfs2: initialize unused bytes in segment summary blocks
+    - memstick: fix memory leak if card device is never registered
+    - kernel/sys.c: fix and improve control flow in __sys_setres[ug]id()
+    - mmc: sdhci_am654: Set HIGH_SPEED_ENA for SDR12 and SDR25
+    - drm/i915: Fix fast wake AUX sync len
+    - mm/khugepaged: check again on anon uffd-wp during isolation
+    - mm: page_alloc: skip regions with hugetlbfs pages when allocating 1G pages
+    - sched/uclamp: Fix fits_capacity() check in feec()
+    - sched/uclamp: Make cpu_overutilized() use util_fits_cpu()
+    - sched/uclamp: Cater for uclamp in find_energy_efficient_cpu()'s early exit
+      condition
+    - sched/fair: Detect capacity inversion
+    - sched/fair: Consider capacity inversion in util_fits_cpu()
+    - sched/uclamp: Fix a uninitialized variable warnings
+    - sched/fair: Fixes for capacity inversion detection
+    - MIPS: Define RUNTIME_DISCARD_EXIT in LD script
+    - docs: futex: Fix kernel-doc references after code split-up preparation
+    - purgatory: fix disabling debug info
+    - fuse: fix attr version comparison in fuse_read_update_size()
+    - fuse: always revalidate rename target dentry
+    - fuse: fix deadlock between atomic O_TRUNC and page invalidation
+    - udp: Call inet6_destroy_sock() in setsockopt(IPV6_ADDRFORM).
+    - tcp/udp: Call inet6_destroy_sock() in IPv6 sk->sk_destruct().
+    - inet6: Remove inet6_destroy_sock() in sk->sk_prot->destroy().
+    - dccp: Call inet6_destroy_sock() via sk->sk_destruct().
+    - sctp: Call inet6_destroy_sock() via sk->sk_destruct().
+    - pwm: meson: Explicitly set .polarity in .get_state()
+    - pwm: iqs620a: Explicitly set .polarity in .get_state()
+    - pwm: hibvt: Explicitly set .polarity in .get_state()
+    - counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
+    - iio: adc: at91-sama5d2_adc: fix an error code in at91_adc_allocate_trigger()
+    - mm/page_alloc: fix potential deadlock on zonelist_update_seq seqlock
+    - ASoC: fsl_asrc_dma: fix potential null-ptr-deref
+    - ASN.1: Fix check for strdup() success
+    - soc: sifive: l2_cache: fix missing iounmap() in error path in
+      sifive_l2_init()
+    - soc: sifive: l2_cache: fix missing free_irq() in error path in
+      sifive_l2_init()
+    - soc: sifive: l2_cache: fix missing of_node_put() in sifive_l2_init()
+    - Linux 5.15.109
+  * Disable hv-kvp-daemon if /dev/vmbus/hv_kvp is not present (LP: #2024900)
+    - [Packaging] disable hv-kvp-daemon if needed
+  * A deadlock issue in scsi rescan task while resuming from S3 (LP: #2018566)
+    - ata: libata-scsi: Avoid deadlock on rescan after device resume
+  * [SRU] Intel Sapphire Rapids HBM support needs CONFIG_NUMA_EMU (LP: #2008745)
+    - [Config] Intel Sapphire Rapids HBM support needs CONFIG_NUMA_EMU
+  * [22.04 FEAT] Enhanced Interpretation for PCI Functions on s390x - kernel
+    part (LP: #1853306)
+    - kvm: use kvfree() in kvm_arch_free_vm()
+    - s390/sclp: add detection of IPL-complete-control facility
+    - s390/pci: use phys_to_virt() for AIBVs/DIBVs
+    - s390/sclp: detect the zPCI load/store interpretation facility
+    - s390/sclp: detect the AISII facility
+    - s390/sclp: detect the AENI facility
+    - s390/sclp: detect the AISI facility
+    - s390/airq: pass more TPI info to airq handlers
+    - s390/airq: allow for airq structure that uses an input vector
+    - s390/pci: externalize the SIC operation controls and routine
+    - s390/pci: stash associated GISA designation
+    - s390/pci: stash dtsm and maxstbl
+    - vfio/pci: introduce CONFIG_VFIO_PCI_ZDEV_KVM
+    - KVM: s390: pci: add basic kvm_zdev structure
+    - KVM: s390: pci: do initial setup for AEN interpretation
+    - KVM: s390: pci: enable host forwarding of Adapter Event Notifications
+    - KVM: s390: mechanism to enable guest zPCI Interpretation
+    - KVM: s390: pci: provide routines for enabling/disabling interrupt forwarding
+    - KVM: s390: pci: add routines to start/stop interpretive execution
+    - vfio-pci/zdev: add open/close device hooks
+    - vfio-pci/zdev: add function handle to clp base capability
+    - vfio-pci/zdev: different maxstbl for interpreted devices
+    - KVM: s390: add KVM_S390_ZPCI_OP to manage guest zPCI devices
+    - MAINTAINERS: additional files related kvm s390 pci passthrough
+    - Documentation: kvm: extend KVM_S390_ZPCI_OP subheading underline
+    - KVM: s390: pci: Hook to access KVM lowlevel from VFIO
+    - KVM: s390: pci: fix plain integer as NULL pointer warnings
+    - KVM: s390: pci: fix GAIT physical vs virtual pointers usage
+    - KVM: s390: pci: register pci hooks without interpretation
+    - [Config] enable VFIO zPCI pass-through for s390x
+  * Undefined Behavior Sanitizer (UBSAN) causes failure to match symbols
+    (LP: #2003374)
+    - [Config] s390x: Re-adding UBSAN to configuration
+  * CVE-2023-35001
+    - netfilter: nf_tables: prevent OOB access in nft_byteorder_eval
+  * CVE-2023-31248
+    - netfilter: nf_tables: do not ignore genmask when looking up chain by id
+  * CVE-2023-3389
+    - io_uring: hold uring mutex around poll removal
+  * CVE-2023-3439
+    - mctp: Add refcounts to mctp_dev
+    - mctp: Allow MCTP on tun devices
+    - mctp: make __mctp_dev_get() take a refcount hold
+    - mctp: defer the kfree of object mdev->addrs
+  * CVE-2023-3390
+    - netfilter: nf_tables: incorrect error path handling with NFT_MSG_NEWRULE
+  * CVE-2023-3141
+    - memstick: r592: Fix UAF bug in r592_remove due to race condition
+  * CVE-2023-3090
+    - ipvlan:Fix out-of-bounds caused by unclear skb->cb
+  * CVE-2022-48502
+    - fs/ntfs3: Check fields while reading
+  * ftrace in ubuntu_kernel_selftests failed with "check if duplicate events are
+    caught" on J-5.15 P9 / J-kvm / L-kvm (LP: #1977827)
+    - SAUCE: selftests/ftrace: Add test dependency
+  * Add microphone support of the front headphone port on P3 Tower
+    (LP: #2023650)
+    - ALSA: hda/realtek: Add Lenovo P3 Tower platform
+  * Add audio support for ThinkPad P1 Gen 6 and Z16 Gen 2 (LP: #2023539)
+    - ALSA: hda/realtek: Add quirks for Lenovo Z13/Z16 Gen2
+    - ALSA: hda/realtek: Add quirk for ThinkPad P1 Gen 6
+  * Resolve synchronous exception on arm64 (LP: #2023311)
+    - arm64: efi: Recover from synchronous exceptions occurring in firmware
+  * Enable Tracing Configs for OSNOISE and TIMERLAT (LP: #2018591)
+    - [Config] Enable OSNOISE_TRACER and TIMERLAT_TRACER configs
+  * Severe NFS performance degradation after LP #2003053 (LP: #2022098)
+    - SAUCE: Make NFS file-access stale cache behaviour opt-in
+  * Encountering an issue with memcpy_fromio causing failed boot of SEV-enabled
+    guest (LP: #2020319)
+    - x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
+  * linux-*: please enable dm-verity kconfigs to allow MoK/db verified root
+    images (LP: #2019040)
+    - [Config] CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG_SECONDARY_KEYRING=y
+  * CVE-2023-2124
+    - xfs: verify buffer contents when we skip log replay
+  * CVE-2023-0597
+    - x86/kasan: Map shadow for percpu pages on demand
+    - x86/mm: Randomize per-cpu entry area
+    - x86/mm: Recompute physical address for every page of per-CPU CEA mapping
+    - x86/mm: Populate KASAN shadow for entire per-CPU range of CPU entry area
+    - x86/mm: Do not shuffle CPU entry areas without KASLR
+  * Jammy update: v5.15.108 upstream stable release (LP: #2023328)
+    - Revert "pinctrl: amd: Disable and mask interrupts on resume"
+    - ALSA: emu10k1: fix capture interrupt handler unlinking
+    - ALSA: hda/sigmatel: add pin overrides for Intel DP45SG motherboard
+    - ALSA: i2c/cs8427: fix iec958 mixer control deactivation
+    - ALSA: firewire-tascam: add missing unwind goto in
+      snd_tscm_stream_start_duplex()
+    - ALSA: emu10k1: don't create old pass-through playback device on Audigy
+    - ALSA: hda/sigmatel: fix S/PDIF out on Intel D*45* motherboards
+    - Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
+    - Bluetooth: Fix race condition in hidp_session_thread
+    - btrfs: print checksum type and implementation at mount time
+    - btrfs: fix fast csum implementation detection
+    - fbmem: Reject FB_ACTIVATE_KD_TEXT from userspace
+    - mtdblock: tolerate corrected bit-flips
+    - mtd: rawnand: meson: fix bitmask for length in command word
+    - mtd: rawnand: stm32_fmc2: remove unsupported EDO mode
+    - mtd: rawnand: stm32_fmc2: use timings.mode instead of checking tRC_min
+    - KVM: arm64: PMU: Restore the guest's EL0 event counting after migration
+    - drm/i915/dsi: fix DSS CTL register offsets for TGL+
+    - clk: sprd: set max_register according to mapping range
+    - RDMA/irdma: Fix memory leak of PBLE objects
+    - RDMA/irdma: Increase iWARP CM default rexmit count
+    - RDMA/irdma: Add ipv4 check to irdma_find_listener()
+    - IB/mlx5: Add support for 400G_8X lane speed
+    - RDMA/cma: Allow UD qp_type to join multicast only
+    - bpf: tcp: Use sock_gen_put instead of sock_put in bpf_iter_tcp
+    - niu: Fix missing unwind goto in niu_alloc_channels()
+    - tcp: restrict net.ipv4.tcp_app_win
+    - drm/armada: Fix a potential double free in an error handling path
+    - qlcnic: check pci_reset_function result
+    - net: qrtr: Fix an uninit variable access bug in qrtr_tx_resume()
+    - sctp: fix a potential overflow in sctp_ifwdtsn_skip
+    - RDMA/core: Fix GID entry ref leak when create_ah fails
+    - udp6: fix potential access to stale information
+    - net: macb: fix a memory corruption in extended buffer descriptor mode
+    - skbuff: Fix a race between coalescing and releasing SKBs
+    - libbpf: Fix single-line struct definition output in btf_dump
+    - ARM: 9290/1: uaccess: Fix KASAN false-positives
+    - power: supply: cros_usbpd: reclassify "default case!" as debug
+    - wifi: mwifiex: mark OF related data as maybe unused
+    - i2c: imx-lpi2c: clean rx/tx buffers upon new message
+    - i2c: hisi: Avoid redundant interrupts
+    - efi: sysfb_efi: Add quirk for Lenovo Yoga Book X91F/L
+    - drm: panel-orientation-quirks: Add quirk for Lenovo Yoga Book X90F
+    - verify_pefile: relax wrapper length check
+    - asymmetric_keys: log on fatal failures in PE/pkcs7
+    - wifi: iwlwifi: mvm: fix mvmtxq->stopped handling
+    - ACPI: resource: Add Medion S17413 to IRQ override quirk
+    - counter: stm32-lptimer-cnt: Provide defines for clock polarities
+    - counter: stm32-timer-cnt: Provide defines for slave mode selection
+    - counter: Internalize sysfs interface code
+    - counter: 104-quad-8: Fix Synapse action reported for Index signals
+    - tracing: Add trace_array_puts() to write into instance
+    - tracing: Have tracing_snapshot_instance_cond() write errors to the
+      appropriate instance
+    - i915/perf: Replace DRM_DEBUG with driver specific drm_dbg call
+    - drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
+    - riscv: add icache flush for nommu sigreturn trampoline
+    - net: sfp: initialize sfp->i2c_block_size at sfp allocation
+    - net: phy: nxp-c45-tja11xx: add remove callback
+    - net: phy: nxp-c45-tja11xx: fix unsigned long multiplication overflow
+    - scsi: ses: Handle enclosure with just a primary component gracefully
+    - x86/PCI: Add quirk for AMD XHCI controller that loses MSI-X state in D3hot
+    - cgroup/cpuset: Wake up cpuset_attach_wq tasks in cpuset_cancel_attach()
+    - mptcp: use mptcp_schedule_work instead of open-coding it
+    - mptcp: stricter state check in mptcp_worker
+    - ubi: Fix failure attaching when vid_hdr offset equals to (sub)page size
+    - ubi: Fix deadlock caused by recursively holding work_sem
+    - powerpc/papr_scm: Update the NUMA distance table for the target node
+    - sched/fair: Move calculate of avg_load to a better location
+    - sched/fair: Fix imbalance overflow
+    - x86/rtc: Remove __init for runtime functions
+    - i2c: ocores: generate stop condition after timeout in polling mode
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S50
+    - nvme-pci: avoid the deepest sleep state on ZHITAI TiPro7000 SSDs
+    - nvme-pci: Crucial P2 has bogus namespace ids
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM610
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM760
+    - nvme-pci: mark Lexar NM760 as IGNORE_DEV_SUBNQN
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD
+    - kexec: turn all kexec_mutex acquisitions into trylocks
+    - panic, kexec: make __crash_kexec() NMI safe
+    - counter: fix docum. build problems after filename change
+    - counter: Add the necessary colons and indents to the comments of
+      counter_compi
+    - nvme-pci: avoid the deepest sleep state on ZHITAI TiPro5000 SSDs
+    - Linux 5.15.108
+  * Jammy update: v5.15.107 upstream stable release (LP: #2023320)
+    - ocfs2: ocfs2_mount_volume does cleanup job before return error
+    - ocfs2: rewrite error handling of ocfs2_fill_super
+    - ocfs2: fix memory leak in ocfs2_mount_volume()
+    - NFSD: Fix sparse warning
+    - NFSD: pass range end to vfs_fsync_range() instead of count
+    - RDMA/irdma: Do not request 2-level PBLEs for CQ alloc
+    - platform/x86: int3472: Split into 2 drivers
+    - [Config] updateconfigs for Intel skl_int3472 driver split
+    - platform/x86: int3472/discrete: Ensure the clk/power enable pins are in
+      output mode
+    - iavf: return errno code instead of status code
+    - iavf/iavf_main: actually log ->src mask when talking about it
+    - serial: 8250_exar: derive nr_ports from PCI ID for Acces I/O cards
+    - serial: exar: Add support for Sealevel 7xxxC serial cards
+    - bpf: hash map, avoid deadlock with suitable hash mask
+    - gpio: GPIO_REGMAP: select REGMAP instead of depending on it
+    - Drivers: vmbus: Check for channel allocation before looking up relids
+    - pwm: cros-ec: Explicitly set .polarity in .get_state()
+    - pwm: sprd: Explicitly set .polarity in .get_state()
+    - KVM: s390: pv: fix external interruption loop not always detected
+    - wifi: mac80211: fix invalid drv_sta_pre_rcu_remove calls for non-uploaded
+      sta
+    - net: qrtr: combine nameservice into main module
+    - [Config] updateconfigs for ns module merger
+    - net: qrtr: Fix a refcount bug in qrtr_recvmsg()
+    - NFSD: Avoid calling OPDESC() with ops->opnum == OP_ILLEGAL
+    - icmp: guard against too small mtu
+    - net: don't let netpoll invoke NAPI if in xmit context
+    - net: dsa: mv88e6xxx: Reset mv88e6393x force WD event bit
+    - sctp: check send stream number after wait_for_sndbuf
+    - net: qrtr: Do not do DEL_SERVER broadcast after DEL_CLIENT
+    - ipv6: Fix an uninit variable access bug in __ip6_make_skb()
+    - platform/x86: think-lmi: Fix memory leak when showing current settings
+    - platform/x86: think-lmi: Fix memory leaks when parsing ThinkStation WMI
+      strings
+    - platform/x86: think-lmi: Clean up display of current_value on Thinkstation
+    - gpio: davinci: Add irq chip flag to skip set wake
+    - net: ethernet: ti: am65-cpsw: Fix mdio cleanup in probe
+    - net: stmmac: fix up RX flow hash indirection table when setting channels
+    - sunrpc: only free unix grouplist after RCU settles
+    - NFSD: callback request does not use correct credential for AUTH_SYS
+    - ice: fix wrong fallback logic for FDIR
+    - ice: Reset FDIR counter in FDIR init stage
+    - ethtool: reset #lanes when lanes is omitted
+    - gve: Secure enough bytes in the first TX desc for all TCP pkts
+    - kbuild: refactor single builds of *.ko
+    - usb: xhci: tegra: fix sleep in atomic call
+    - xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
+    - usb: cdnsp: Fixes error: uninitialized symbol 'len'
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-S
+    - USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs
+    - usb: typec: altmodes/displayport: Fix configure initial pin assignment
+    - USB: serial: option: add Telit FE990 compositions
+    - USB: serial: option: add Quectel RM500U-CN modem
+    - iio: adis16480: select CONFIG_CRC32
+    - iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
+    - iio: dac: cio-dac: Fix max DAC write value check for 12-bit
+    - iio: light: cm32181: Unregister second I2C client if present
+    - tty: serial: sh-sci: Fix transmit end interrupt handler
+    - tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
+    - tty: serial: fsl_lpuart: avoid checking for transfer complete when
+      UARTCTRL_SBK is asserted in lpuart32_tx_empty
+    - nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread()
+    - nilfs2: fix sysfs interface lifetime
+    - dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
+    - ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN
+    - ALSA: hda/realtek: Add quirk for Clevo X370SNW
+    - coresight: etm4x: Do not access TRCIDR1 for identification
+    - coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
+    - iio: adc: ad7791: fix IRQ flags
+    - scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
+    - scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
+    - smb3: allow deferred close timeout to be configurable
+    - smb3: lower default deferred close timeout to address perf regression
+    - cifs: sanitize paths in cifs_update_super_prepath.
+    - perf/core: Fix the same task check in perf_event_set_output
+    - ftrace: Mark get_lock_parent_ip() __always_inline
+    - ftrace: Fix issue that 'direct->addr' not restored in modify_ftrace_direct()
+    - fs: drop peer group ids under namespace lock
+    - can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
+    - can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
+    - tracing: Free error logs of tracing instances
+    - ASoC: hdac_hdmi: use set_stream() instead of set_tdm_slots()
+    - mm: vmalloc: avoid warn_alloc noise caused by fatal signal
+    - drm/panfrost: Fix the panfrost_mmu_map_fault_addr() error path
+    - drm/nouveau/disp: Support more modes by checking with lower bpc
+    - ring-buffer: Fix race while reader and writer are on the same page
+    - mm/swap: fix swap_info_struct race between swapoff and get_swap_pages()
+    - drm/bridge: lt9611: Fix PLL being unable to lock
+    - mm: take a page reference when removing device exclusive entries
+    - kbuild: fix single directory build
+    - ocfs2: fix freeing uninitialized resource on ocfs2_dlm_shutdown
+    - bpftool: Print newline before '}' for struct with padding only fields
+    - Linux 5.15.107
+  * Jammy update: v5.15.106 upstream stable release (LP: #2023233)
+    - fsverity: don't drop pagecache at end of FS_IOC_ENABLE_VERITY
+    - usb: dwc3: gadget: move cmd_endtransfer to extra function
+    - usb: dwc3: gadget: Add 1ms delay after end transfer command without IOC
+    - kernel: kcsan: kcsan_test: build without structleak plugin
+    - kcsan: avoid passing -g for test
+    - ksmbd: don't terminate inactive sessions after a few seconds
+    - bus: imx-weim: fix branch condition evaluates to a garbage value
+    - xfrm: Zero padding when dumping algos and encap
+    - ASoC: codecs: tx-macro: Fix for KASAN: slab-out-of-bounds
+    - md: avoid signed overflow in slot_store()
+    - x86/PVH: obtain VGA console info in Dom0
+    - net: hsr: Don't log netdev_err message on unknown prp dst node
+    - ALSA: asihpi: check pao in control_message()
+    - ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
+    - fbdev: tgafb: Fix potential divide by zero
+    - sched_getaffinity: don't assume 'cpumask_size()' is fully initialized
+    - fbdev: nvidia: Fix potential divide by zero
+    - fbdev: intelfb: Fix potential divide by zero
+    - fbdev: lxfb: Fix potential divide by zero
+    - fbdev: au1200fb: Fix potential divide by zero
+    - tools/power turbostat: Fix /dev/cpu_dma_latency warnings
+    - tools/power turbostat: fix decoding of HWP_STATUS
+    - tracing: Fix wrong return in kprobe_event_gen_test.c
+    - ca8210: Fix unsigned mac_len comparison with zero in ca8210_skb_tx()
+    - mips: bmips: BCM6358: disable RAC flush for TP1
+    - ALSA: usb-audio: Fix recursive locking at XRUN during syncing
+    - platform/x86: think-lmi: add missing type attribute
+    - platform/x86: think-lmi: use correct possible_values delimiters
+    - platform/x86: think-lmi: only display possible_values if available
+    - platform/x86: think-lmi: Add possible_values for ThinkStation
+    - mtd: rawnand: meson: invalidate cache on polling ECC bit
+    - SUNRPC: fix shutdown of NFS TCP client socket
+    - sfc: ef10: don't overwrite offload features at NIC reset
+    - scsi: megaraid_sas: Fix crash after a double completion
+    - scsi: mpt3sas: Don't print sense pool info twice
+    - ptp_qoriq: fix memory leak in probe()
+    - net: dsa: microchip: ksz8863_smi: fix bulk access
+    - r8169: fix RTL8168H and RTL8107E rx crc error
+    - regulator: Handle deferred clk
+    - net/net_failover: fix txq exceeding warning
+    - net: stmmac: don't reject VLANs when IFF_PROMISC is set
+    - drm/i915/tc: Fix the ICL PHY ownership check in TC-cold state
+    - platform/x86/intel/pmc: Alder Lake PCH slp_s0_residency fix
+    - can: bcm: bcm_tx_setup(): fix KMSAN uninit-value in vfs_write
+    - s390/vfio-ap: fix memory leak in vfio_ap device driver
+    - loop: suppress uevents while reconfiguring the device
+    - loop: LOOP_CONFIGURE: send uevents for partitions
+    - net: mvpp2: classifier flow fix fragmentation flags
+    - net: mvpp2: parser fix QinQ
+    - net: mvpp2: parser fix PPPoE
+    - smsc911x: avoid PHY being resumed when interface is not up
+    - ice: add profile conflict check for AVF FDIR
+    - ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
+    - ALSA: ymfpci: Create card with device-managed snd_devm_card_new()
+    - ALSA: ymfpci: Fix BUG_ON in probe function
+    - net: ipa: compute DMA pool size properly
+    - i40e: fix registers dump after run ethtool adapter self test
+    - bnxt_en: Fix reporting of test result in ethtool selftest
+    - bnxt_en: Fix typo in PCI id to device description string mapping
+    - bnxt_en: Add missing 200G link speed reporting
+    - net: dsa: mv88e6xxx: Enable IGMP snooping on user ports only
+    - net: ethernet: mtk_eth_soc: fix flow block refcounting logic
+    - pinctrl: ocelot: Fix alt mode for ocelot
+    - iommu/vt-d: Allow zero SAGAW if second-stage not supported
+    - Input: alps - fix compatibility with -funsigned-char
+    - Input: focaltech - use explicitly signed char type
+    - cifs: prevent infinite recursion in CIFSGetDFSRefer()
+    - cifs: fix DFS traversal oops without CONFIG_CIFS_DFS_UPCALL
+    - Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table
+    - btrfs: fix race between quota disable and quota assign ioctls
+    - btrfs: scan device in non-exclusive mode
+    - zonefs: Always invalidate last cached page on append write
+    - can: j1939: prevent deadlock by moving j1939_sk_errqueue()
+    - xen/netback: don't do grant copy across page boundary
+    - net: phy: dp83869: fix default value for tx-/rx-internal-delay
+    - pinctrl: amd: Disable and mask interrupts on resume
+    - pinctrl: at91-pio4: fix domain name assignment
+    - powerpc: Don't try to copy PPR for task with NULL pt_regs
+    - NFSv4: Fix hangs when recovering open state after a server reboot
+    - ALSA: hda/conexant: Partial revert of a quirk for Lenovo
+    - ALSA: usb-audio: Fix regression on detection of Roland VS-100
+    - ALSA: hda/realtek: Add quirks for some Clevo laptops
+    - ALSA: hda/realtek: Add quirk for Lenovo ZhaoYang CF4620Z
+    - xtensa: fix KASAN report for show_stack
+    - rcu: Fix rcu_torture_read ftrace event
+    - drm/etnaviv: fix reference leak when mmaping imported buffer
+    - drm/amd/display: Add DSC Support for Synaptics Cascaded MST Hub
+    - KVM: arm64: Disable interrupts while walking userspace PTs
+    - KVM: VMX: Move preemption timer <=> hrtimer dance to common x86
+    - KVM: x86: Inject #GP on x2APIC WRMSR that sets reserved bits 63:32
+    - KVM: x86: Purge "highest ISR" cache when updating APICv state
+    - zonefs: Fix error message in zonefs_file_dio_append()
+    - selftests/bpf: Test btf dump for struct with padding only fields
+    - libbpf: Fix BTF-to-C converter's padding logic
+    - selftests/bpf: Add few corner cases to test padding handling of btf_dump
+    - libbpf: Fix btf_dump's packed struct determination
+    - hsr: ratelimit only when errors are printed
+    - x86/PVH: avoid 32-bit build warning when obtaining VGA console info
+    - Linux 5.15.106
+  * Jammy update: v5.15.105 upstream stable release (LP: #2023230)
+    - interconnect: qcom: osm-l3: fix icc_onecell_data allocation
+    - perf/core: Fix perf_output_begin parameter is incorrectly invoked in
+      perf_event_bpf_output
+    - perf: fix perf_event_context->time
+    - tracing/hwlat: Replace sched_setaffinity with set_cpus_allowed_ptr
+    - serial: fsl_lpuart: Fix comment typo
+    - tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
+    - tty: serial: fsl_lpuart: fix race on RX DMA shutdown
+    - serial: 8250: SERIAL_8250_ASPEED_VUART should depend on ARCH_ASPEED
+    - [Config] updateconfigs for SERIAL_8250_ASPEED_VUART
+    - serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
+    - kthread: add the helper function kthread_run_on_cpu()
+    - trace/hwlat: make use of the helper function kthread_run_on_cpu()
+    - trace/hwlat: Do not start per-cpu thread if it is already running
+    - net: tls: fix possible race condition between do_tls_getsockopt_conf() and
+      do_tls_setsockopt_conf()
+    - power: supply: bq24190_charger: using pm_runtime_resume_and_get instead of
+      pm_runtime_get_sync
+    - power: supply: bq24190: Fix use after free bug in bq24190_remove due to race
+      condition
+    - power: supply: da9150: Fix use after free bug in da9150_charger_remove due
+      to race condition
+    - ARM: dts: imx6sll: e60k02: fix usbotg1 pinctrl
+    - ARM: dts: imx6sl: tolino-shine2hd: fix usbotg1 pinctrl
+    - arm64: dts: imx8mn: specify #sound-dai-cells for SAI nodes
+    - xsk: Add missing overflow check in xdp_umem_reg
+    - iavf: fix inverted Rx hash condition leading to disabled hash
+    - iavf: fix non-tunneled IPv6 UDP packet type and hashing
+    - intel/igbvf: free irq on the error path in igbvf_request_msix()
+    - igbvf: Regard vf reset nack as success
+    - igc: fix the validation logic for taprio's gate list
+    - i2c: imx-lpi2c: check only for enabled interrupt flags
+    - i2c: hisi: Only use the completion interrupt to finish the transfer
+    - scsi: scsi_dh_alua: Fix memleak for 'qdata' in alua_activate()
+    - net: dsa: b53: mmap: fix device tree support
+    - net: usb: smsc95xx: Limit packet length to skb->len
+    - qed/qed_sriov: guard against NULL derefs from qed_iov_get_vf_info
+    - net: phy: Ensure state transitions are processed from phy_stop()
+    - net: mdio: fix owner field for mdio buses registered using device-tree
+    - net: mdio: fix owner field for mdio buses registered using ACPI
+    - drm/i915/gt: perform uc late init after probe error injection
+    - net: qcom/emac: Fix use after free bug in emac_remove due to race condition
+    - net/ps3_gelic_net: Fix RX sk_buff length
+    - net/ps3_gelic_net: Use dma_mapping_error
+    - octeontx2-vf: Add missing free for alloc_percpu
+    - bootconfig: Fix testcase to increase max node
+    - keys: Do not cache key in task struct if key is requested from kernel thread
+    - iavf: fix hang on reboot with ice
+    - i40e: fix flow director packet filter programming
+    - bpf: Adjust insufficient default bpf_jit_limit
+    - net/mlx5e: Set uplink rep as NETNS_LOCAL
+    - net/mlx5: Fix steering rules cleanup
+    - net/mlx5: Read the TC mapping of all priorities on ETS query
+    - net/mlx5: E-Switch, Fix an Oops in error handling code
+    - net: dsa: tag_brcm: legacy: fix daisy-chained switches
+    - atm: idt77252: fix kmemleak when rmmod idt77252
+    - erspan: do not use skb_mac_header() in ndo_start_xmit()
+    - net/sonic: use dma_mapping_error() for error check
+    - nvme-tcp: fix nvme_tcp_term_pdu to match spec
+    - hvc/xen: prevent concurrent accesses to the shared ring
+    - ksmbd: add low bound validation to FSCTL_SET_ZERO_DATA
+    - ksmbd: add low bound validation to FSCTL_QUERY_ALLOCATED_RANGES
+    - ksmbd: fix possible refcount leak in smb2_open()
+    - gve: Cache link_speed value from device
+    - net: dsa: mt7530: move enabling disabling core clock to mt7530_pll_setup()
+    - net: dsa: mt7530: move lowering TRGMII driving to mt7530_setup()
+    - net: dsa: mt7530: move setting ssc_delta to PHY_INTERFACE_MODE_TRGMII case
+    - net: mdio: thunder: Add missing fwnode_handle_put()
+    - Bluetooth: btqcomsmd: Fix command timeout after setting BD address
+    - Bluetooth: L2CAP: Fix responding with wrong PDU type
+    - platform/chrome: cros_ec_chardev: fix kernel data leak from ioctl
+    - thread_info: Add helpers to snapshot thread flags
+    - entry: Snapshot thread flags
+    - entry/rcu: Check TIF_RESCHED _after_ delayed RCU wake-up
+    - hwmon: fix potential sensor registration fail if of_node is missing
+    - hwmon (it87): Fix voltage scaling for chips with 10.9mV ADCs
+    - scsi: qla2xxx: Synchronize the IOCB count to be in order
+    - scsi: qla2xxx: Perform lockless command completion in abort path
+    - uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS583Gen 2
+    - thunderbolt: Use scale field when allocating USB3 bandwidth
+    - thunderbolt: Call tb_check_quirks() after initializing adapters
+    - thunderbolt: Disable interrupt auto clear for rings
+    - thunderbolt: Add missing UNSET_INBOUND_SBTX for retimer access
+    - thunderbolt: Use const qualifier for `ring_interrupt_index`
+    - thunderbolt: Rename shadowed variables bit to interrupt_bit and
+      auto_clear_bit
+    - ACPI: x86: utils: Add Cezanne to the list for forcing StorageD3Enable
+    - riscv: Bump COMMAND_LINE_SIZE value to 1024
+    - drm/cirrus: NULL-check pipe->plane.state->fb in cirrus_pipe_update()
+    - HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
+    - ca8210: fix mac_len negative array access
+    - HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
+    - m68k: Only force 030 bus error if PC not in exception table
+    - selftests/bpf: check that modifier resolves after pointer
+    - scsi: target: iscsi: Fix an error message in iscsi_check_key()
+    - scsi: hisi_sas: Check devm_add_action() return value
+    - scsi: ufs: core: Add soft dependency on governor_simpleondemand
+    - scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read()
+    - scsi: lpfc: Avoid usage of list iterator variable after loop
+    - scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
+    - net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
+    - net: usb: qmi_wwan: add Telit 0x1080 composition
+    - sh: sanitize the flags on sigreturn
+    - net/sched: act_mirred: better wording on protection against excessive stack
+      growth
+    - act_mirred: use the backlog for nested calls to mirred ingress
+    - cifs: empty interface list when server doesn't support query interfaces
+    - cifs: print session id while listing open files
+    - scsi: core: Add BLIST_SKIP_VPD_PAGES for SKhynix H28U74301AMR
+    - usb: dwc2: fix a devres leak in hw_enable upon suspend resume
+    - usb: gadget: u_audio: don't let userspace block driver unbind
+    - efi: sysfb_efi: Fix DMI quirks not working for simpledrm
+    - mm/slab: Fix undefined init_cache_node_node() for NUMA and !SMP
+    - fscrypt: destroy keyring after security_sb_delete()
+    - fsverity: Remove WQ_UNBOUND from fsverity read workqueue
+    - lockd: set file_lock start and end when decoding nlm4 testargs
+    - arm64: dts: imx8mm-nitrogen-r2: fix WM8960 clock name
+    - igb: revert rtnl_lock() that causes deadlock
+    - dm thin: fix deadlock when swapping to thin device
+    - usb: typec: tcpm: fix warning when handle discover_identity message
+    - usb: cdns3: Fix issue with using incorrect PCI device function
+    - usb: cdnsp: Fixes issue with redundant Status Stage
+    - usb: cdnsp: changes PCI Device ID to fix conflict with CNDS3 driver
+    - usb: chipdea: core: fix return -EINVAL if request role is the same with
+      current role
+    - usb: chipidea: core: fix possible concurrent when switch role
+    - usb: ucsi: Fix NULL pointer deref in ucsi_connector_change()
+    - kfence: avoid passing -g for test
+    - KVM: x86: hyper-v: Avoid calling kvm_make_vcpus_request_mask() with
+      vcpu_mask==NULL
+    - ksmbd: set FILE_NAMED_STREAMS attribute in FS_ATTRIBUTE_INFORMATION
+    - ksmbd: return STATUS_NOT_SUPPORTED on unsupported smb2.0 dialect
+    - ksmbd: return unsupported error on smb1 mount
+    - wifi: mac80211: fix qos on mesh interfaces
+    - nilfs2: fix kernel-infoleak in nilfs_ioctl_wrap_copy()
+    - drm/bridge: lt8912b: return EPROBE_DEFER if bridge is not found
+    - drm/meson: fix missing component unbind on bind errors
+    - drm/amdgpu/nv: Apply ASPM quirk on Intel ADL + AMD Navi
+    - drm/i915/active: Fix missing debug object activation
+    - drm/i915: Preserve crtc_state->inherited during state clearing
+    - riscv: mm: Fix incorrect ASID argument when flushing TLB
+    - riscv: Handle zicsr/zifencei issues between clang and binutils
+    - tee: amdtee: fix race condition in amdtee_open_session
+    - firmware: arm_scmi: Fix device node validation for mailbox transport
+    - i2c: xgene-slimpro: Fix out-of-bounds bug in xgene_slimpro_i2c_xfer()
+    - dm stats: check for and propagate alloc_percpu failure
+    - dm crypt: add cond_resched() to dmcrypt_write()
+    - dm crypt: avoid accessing uninitialized tasklet
+    - sched/fair: sanitize vruntime of entity being placed
+    - sched/fair: Sanitize vruntime of entity being migrated
+    - mm: kfence: fix using kfence_metadata without initialization in
+      show_object()
+    - ocfs2: fix data corruption after failed write
+    - Linux 5.15.105
+  * Jammy update: v5.15.104 upstream stable release (LP: #2023225)
+    - xfrm: Allow transport-mode states with AF_UNSPEC selector
+    - drm/panfrost: Don't sync rpm suspension after mmu flushing
+    - cifs: Move the in_send statistic to __smb_send_rqst()
+    - drm/meson: fix 1px pink line on GXM when scaling video overlay
+    - clk: HI655X: select REGMAP instead of depending on it
+    - docs: Correct missing "d_" prefix for dentry_operations member
+      d_weak_revalidate
+    - scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add()
+    - ALSA: hda: Match only Intel devices with CONTROLLER_IN_GPU()
+    - netfilter: nft_nat: correct length for loading protocol registers
+    - netfilter: nft_masq: correct length for loading protocol registers
+    - netfilter: nft_redir: correct length for loading protocol registers
+    - netfilter: nft_redir: correct value of inet type `.maxattrs`
+    - scsi: core: Fix a procfs host directory removal regression
+    - tcp: tcp_make_synack() can be called from process context
+    - nfc: pn533: initialize struct pn533_out_arg properly
+    - ipvlan: Make skb->skb_iif track skb->dev for l3s mode
+    - i40e: Fix kernel crash during reboot when adapter is in recovery mode
+    - vdpa_sim: not reset state in vdpasim_queue_ready
+    - vdpa_sim: set last_used_idx as last_avail_idx in vdpasim_queue_ready
+    - PCI: s390: Fix use-after-free of PCI resources with per-function hotplug
+    - drm/i915/display: Workaround cursor left overs with PSR2 selective fetch
+      enabled
+    - drm/i915/display/psr: Use drm damage helpers to calculate plane damaged area
+    - drm/i915/display: clean up comments
+    - drm/i915/psr: Use calculated io and fast wake lines
+    - net/smc: fix NULL sndbuf_desc in smc_cdc_tx_handler()
+    - qed/qed_dev: guard against a possible division by zero
+    - net: dsa: mt7530: remove now incorrect comment regarding port 5
+    - net: dsa: mt7530: set PLL frequency and trgmii only when trgmii is used
+    - loop: Fix use-after-free issues
+    - net: tunnels: annotate lockless accesses to dev->needed_headroom
+    - net: phy: smsc: bail out in lan87xx_read_status if genphy_read_status fails
+    - nfc: st-nci: Fix use after free bug in ndlc_remove due to race condition
+    - net/smc: fix deadlock triggered by cancel_delayed_work_syn()
+    - net: usb: smsc75xx: Limit packet length to skb->len
+    - drm/bridge: Fix returned array size name for atomic_get_input_bus_fmts kdoc
+    - block: null_blk: Fix handling of fake timeout request
+    - nvme: fix handling single range discard request
+    - nvmet: avoid potential UAF in nvmet_req_complete()
+    - block: sunvdc: add check for mdesc_grab() returning NULL
+    - ice: xsk: disable txq irq before flushing hw
+    - net: dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
+    - ravb: avoid PHY being resumed when interface is not up
+    - sh_eth: avoid PHY being resumed when interface is not up
+    - ipv4: Fix incorrect table ID in IOCTL path
+    - net: usb: smsc75xx: Move packet length check to prevent kernel panic in
+      skb_pull
+    - net/iucv: Fix size of interrupt data
+    - qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
+    - ethernet: sun: add check for the mdesc_grab()
+    - bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
+    - bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
+    - hwmon: (adt7475) Display smoothing attributes in correct order
+    - hwmon: (adt7475) Fix masking of hysteresis registers
+    - hwmon: (xgene) Fix use after free bug in xgene_hwmon_remove due to race
+      condition
+    - hwmon: (ina3221) return prober error code
+    - hwmon: (ucd90320) Add minimum delay between bus accesses
+    - hwmon: tmp512: drop of_match_ptr for ID table
+    - kconfig: Update config changed flag before calling callback
+    - hwmon: (adm1266) Set `can_sleep` flag for GPIO chip
+    - hwmon: (ltc2992) Set `can_sleep` flag for GPIO chip
+    - media: m5mols: fix off-by-one loop termination error
+    - mmc: atmel-mci: fix race between stop command and start of next command
+    - jffs2: correct logic when creating a hole in jffs2_write_begin
+    - ext4: fail ext4_iget if special inode unallocated
+    - ext4: update s_journal_inum if it changes after journal replay
+    - ext4: fix task hung in ext4_xattr_delete_inode
+    - drm/amdkfd: Fix an illegal memory access
+    - net/9p: fix bug in client create for .L
+    - sh: intc: Avoid spurious sizeof-pointer-div warning
+    - drm/amd/display: fix shift-out-of-bounds in CalculateVMAndRowBytes
+    - ext4: fix possible double unlock when moving a directory
+    - tty: serial: fsl_lpuart: skip waiting for transmission complete when
+      UARTCTRL_SBK is asserted
+    - serial: 8250_em: Fix UART port type
+    - serial: 8250_fsl: fix handle_irq locking
+    - firmware: xilinx: don't make a sleepable memory allocation from an atomic
+      context
+    - s390/ipl: add missing intersection check to ipl_report handling
+    - interconnect: fix mem leak when freeing nodes
+    - interconnect: exynos: fix node leak in probe PM QoS error path
+    - tracing: Make splice_read available again
+    - tracing: Check field value in hist_field_name()
+    - tracing: Make tracepoint lockdep check actually test something
+    - cifs: Fix smb2_set_path_size()
+    - ALSA: hda: intel-dsp-config: add MTL PCI id
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro
+    - Revert "riscv: mm: notify remote harts about mmu cache updates"
+    - riscv: asid: Fixup stale TLB entry cause application crash
+    - drm/shmem-helper: Remove another errant put in error path
+    - drm/sun4i: fix missing component unbind on bind errors
+    - drm/amd/pm: Fix sienna cichlid incorrect OD volage after resume
+    - mptcp: fix possible deadlock in subflow_error_report
+    - mptcp: add ro_after_init for tcp{,v6}_prot_override
+    - mptcp: avoid setting TCP_CLOSE state twice
+    - mptcp: fix lockdep false positive in mptcp_pm_nl_create_listen_socket()
+    - ftrace: Fix invalid address access in lookup_rec() when index is 0
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV3000
+    - mm/userfaultfd: propagate uffd-wp bit when PTE-mapping the huge zeropage
+    - mmc: sdhci_am654: lower power-on failed message severity
+    - fbdev: stifb: Provide valid pixelclock and add fb_check_var() checks
+    - trace/hwlat: Do not wipe the contents of per-cpu thread data
+    - net: phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit
+    - cpuidle: psci: Iterate backwards over list in psci_pd_remove()
+    - x86/mce: Make sure logged MCEs are processed after sysfs update
+    - x86/mm: Fix use of uninitialized buffer in sme_enable()
+    - x86/resctrl: Clear staged_config[] before and after it is used
+    - drm/i915: Don't use stolen memory for ring buffers with LLC
+    - drm/i915/active: Fix misuse of non-idle barriers as fence trackers
+    - io_uring: avoid null-ptr-deref in io_arm_poll_handler
+    - PCI: Unify delay handling for reset and resume
+    - PCI/DPC: Await readiness of secondary bus after reset
+    - HID: core: Provide new max_buffer_size attribute to over-ride the default
+    - HID: uhid: Over-ride the default maximum data buffer value with our own
+    - perf: Fix check before add_event_to_groups() in perf_group_detach()
+    - Linux 5.15.104
+  * Jammy update: v5.15.103 upstream stable release (LP: #2023224)
+    - fs: prevent out-of-bounds array speculation when closing a file descriptor
+    - btrfs: fix percent calculation for bg reclaim message
+    - perf inject: Fix --buildid-all not to eat up MMAP2
+    - fork: allow CLONE_NEWTIME in clone3 flags
+    - x86/CPU/AMD: Disable XSAVES on AMD family 0x17
+    - drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc15
+    - drm/connector: print max_requested_bpc in state debugfs
+    - staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
+    - ext4: fix cgroup writeback accounting with fs-layer encryption
+    - ext4: fix RENAME_WHITEOUT handling for inline directories
+    - ext4: fix another off-by-one fsmap error on 1k block filesystems
+    - ext4: move where set the MAY_INLINE_DATA flag is set
+    - ext4: fix WARNING in ext4_update_inline_data
+    - ext4: zero i_disksize when initializing the bootloader inode
+    - nfc: change order inside nfc_se_io error path
+    - KVM: Optimize kvm_make_vcpus_request_mask() a bit
+    - KVM: Pre-allocate cpumasks for kvm_make_all_cpus_request_except()
+    - KVM: Register /dev/kvm as the _very_ last thing during initialization
+    - KVM: SVM: Don't rewrite guest ICR on AVIC IPI virtualization failure
+    - KVM: SVM: Process ICR on AVIC IPI delivery failure due to invalid target
+    - fs: dlm: fix log of lowcomms vs midcomms
+    - fs: dlm: add midcomms init/start functions
+    - fs: dlm: start midcomms before scand
+    - udf: Fix off-by-one error when discarding preallocation
+    - f2fs: avoid down_write on nat_tree_lock during checkpoint
+    - f2fs: do not bother checkpoint by f2fs_get_node_info
+    - f2fs: retry to update the inode page given data corruption
+    - ipmi:ssif: Increase the message retry time
+    - ipmi:ssif: Add a timer between request retries
+    - irqdomain: Refactor __irq_domain_alloc_irqs()
+    - iommu/vt-d: Fix PASID directory pointer coherency
+    - block/brd: add error handling support for add_disk()
+    - brd: mark as nowait compatible
+    - arm64: efi: Make efi_rt_lock a raw_spinlock
+    - RISC-V: Avoid dereferening NULL regs in die()
+    - riscv: Avoid enabling interrupts in die()
+    - riscv: Add header include guards to insn.h
+    - scsi: core: Remove the /proc/scsi/${proc_name} directory earlier
+    - regulator: Flag uncontrollable regulators as always_on
+    - regulator: core: Fix off-on-delay-us for always-on/boot-on regulators
+    - regulator: core: Use ktime_get_boottime() to determine how long a regulator
+      was off
+    - ext4: Fix possible corruption when moving a directory
+    - drm/nouveau/kms/nv50-: remove unused functions
+    - drm/nouveau/kms/nv50: fix nv50_wndw_new_ prototype
+    - drm/msm: Fix potential invalid ptr free
+    - drm/msm/a5xx: fix setting of the CP_PREEMPT_ENABLE_LOCAL register
+    - drm/msm/a5xx: fix highest bank bit for a530
+    - drm/msm/a5xx: fix the emptyness check in the preempt code
+    - drm/msm/a5xx: fix context faults during ring switch
+    - bgmac: fix *initial* chip reset to support BCM5358
+    - nfc: fdp: add null check of devm_kmalloc_array in
+      fdp_nci_i2c_read_device_properties
+    - powerpc: dts: t1040rdb: fix compatible string for Rev A boards
+    - ila: do not generate empty messages in ila_xlat_nl_cmd_get_mapping()
+    - selftests: nft_nat: ensuring the listening side is up before starting the
+      client
+    - perf stat: Fix counting when initial delay configured
+    - net: lan78xx: fix accessing the LAN7800's internal phy specific registers
+      from the MAC driver
+    - net: caif: Fix use-after-free in cfusbl_device_notify()
+    - ice: copy last block omitted in ice_get_module_eeprom()
+    - bpf, sockmap: Fix an infinite loop error when len is 0 in
+      tcp_bpf_recvmsg_parser()
+    - drm/msm/dpu: fix len of sc7180 ctl blocks
+    - net: stmmac: add to set device wake up flag when stmmac init phy
+    - net: phylib: get rid of unnecessary locking
+    - bnxt_en: Avoid order-5 memory allocation for TPA data
+    - netfilter: tproxy: fix deadlock due to missing BH disable
+    - btf: fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
+    - net: phy: smsc: Cache interrupt mask
+    - net: phy: smsc: fix link up detection in forced irq mode
+    - net: ethernet: mtk_eth_soc: fix RX data corruption issue
+    - scsi: megaraid_sas: Update max supported LD IDs to 240
+    - platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
+    - net/smc: fix fallback failed while sendmsg with fastopen
+    - octeontx2-af: Unlock contexts in the queue context cache in case of fault
+      detection
+    - SUNRPC: Fix a server shutdown leak
+    - net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
+    - af_unix: Remove unnecessary brackets around CONFIG_AF_UNIX_OOB.
+    - af_unix: fix struct pid leaks in OOB support
+    - riscv: Use READ_ONCE_NOCHECK in imprecise unwinding stack mode
+    - s390/ftrace: remove dead code
+    - RISC-V: Don't check text_mutex during stop_machine
+    - ext4: Fix deadlock during directory rename
+    - irqdomain: Fix mapping-creation race
+    - nbd: use the correct block_device in nbd_bdev_reset
+    - iommu/amd: Add PCI segment support for ivrs_[ioapic/hpet/acpihid] commands
+    - iommu/amd: Fix ill-formed ivrs_ioapic, ivrs_hpet and ivrs_acpihid options
+    - iommu/amd: Add a length limitation for the ivrs_acpihid command-line
+      parameter
+    - staging: rtl8723bs: clean up comparsions to NULL
+    - Staging: rtl8723bs: Placing opening { braces in previous line
+    - staging: rtl8723bs: fix placement of braces
+    - staging: rtl8723bs: Fix key-store index handling
+    - watch_queue: fix IOC_WATCH_QUEUE_SET_SIZE alloc error paths
+    - tpm/eventlog: Don't abort tpm_read_log on faulty ACPI address
+    - xfs: use setattr_copy to set vfs inode attributes
+    - xfs: remove XFS_PREALLOC_SYNC
+    - xfs: fallocate() should call file_modified()
+    - xfs: set prealloc flag in xfs_alloc_file_space()
+    - fs: add mode_strip_sgid() helper
+    - fs: move S_ISGID stripping into the vfs_*() helpers
+    - attr: add in_group_or_capable()
+    - fs: move should_remove_suid()
+    - attr: add setattr_should_drop_sgid()
+    - attr: use consistent sgid stripping checks
+    - fs: use consistent setgid checks in is_sxid()
+    - MIPS: Fix a compilation issue
+    - powerpc/iommu: fix memory leak with using debugfs_lookup()
+    - powerpc/kcsan: Exclude udelay to prevent recursive instrumentation
+    - alpha: fix R_ALPHA_LITERAL reloc for large modules
+    - macintosh: windfarm: Use unsigned type for 1-bit bitfields
+    - PCI: Add SolidRun vendor ID
+    - scripts: handle BrokenPipeError for python scripts
+    - media: ov5640: Fix analogue gain control
+    - media: rc: gpio-ir-recv: add remove function
+    - filelocks: use mount idmapping for setlease permission check
+    - ext4: refactor ext4_free_blocks() to pull out ext4_mb_clear_bb()
+    - ext4: add ext4_sb_block_valid() refactored out of ext4_inode_block_valid()
+    - ext4: add strict range checks while freeing blocks
+    - ext4: block range must be validated before use in ext4_mb_clear_bb()
+    - arch: fix broken BuildID for arm64 and riscv
+    - powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT
+    - powerpc/vmlinux.lds: Don't discard .rela* for relocatable builds
+    - s390: define RUNTIME_DISCARD_EXIT to fix link error with GNU ld < 2.36
+    - sh: define RUNTIME_DISCARD_EXIT
+    - tools build: Add feature test for init_disassemble_info API changes
+    - tools include: add dis-asm-compat.h to handle version differences
+    - tools perf: Fix compilation error with new binutils
+    - tools bpf_jit_disasm: Fix compilation error with new binutils
+    - tools bpftool: Fix compilation error with new binutils
+    - KVM: fix memoryleak in kvm_init()
+    - xfs: remove xfs_setattr_time() declaration
+    - UML: define RUNTIME_DISCARD_EXIT
+    - fs: hold writers when changing mount's idmapping
+    - KVM: nVMX: Don't use Enlightened MSR Bitmap for L3
+    - KVM: VMX: Introduce vmx_msr_bitmap_l01_changed() helper
+    - KVM: VMX: Fix crash due to uninitialized current_vmcs
+    - Makefile: use -gdwarf-{4|5} for assembler for DEBUG_INFO_DWARF{4|5}
+    - Linux 5.15.103
+  * Jammy update: v5.15.102 upstream stable release (LP: #2020393)
+    - staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
+    - staging: rtl8192e: Remove call_usermodehelper starting RadioPower.sh
+    - Linux 5.15.102
+  * Jammy update: v5.15.101 upstream stable release (LP: #2020391)
+    - Linux 5.15.101
+  * Jammy update: v5.15.100 upstream stable release (LP: #2020387)
+    - auxdisplay: hd44780: Fix potential memory leak in hd44780_remove()
+    - fs/jfs: fix shift exponent db_agl2size negative
+    - objtool: Fix memory leak in create_static_call_sections()
+    - pwm: sifive: Reduce time the controller lock is held
+    - pwm: sifive: Always let the first pwm_apply_state succeed
+    - pwm: stm32-lp: fix the check on arr and cmp registers update
+    - f2fs: use memcpy_{to,from}_page() where possible
+    - fs: f2fs: initialize fsdata in pagecache_write()
+    - f2fs: allow set compression option of files without blocks
+    - um: vector: Fix memory leak in vector_config
+    - ubi: ensure that VID header offset + VID header size <= alloc, size
+    - ubifs: Fix build errors as symbol undefined
+    - ubifs: Rectify space budget for ubifs_symlink() if symlink is encrypted
+    - ubifs: Rectify space budget for ubifs_xrename()
+    - ubifs: Fix wrong dirty space budget for dirty inode
+    - ubifs: do_rename: Fix wrong space budget when target inode's nlink > 1
+    - ubifs: Reserve one leb for each journal head while doing budget
+    - ubi: Fix use-after-free when volume resizing failed
+    - ubi: Fix unreferenced object reported by kmemleak in ubi_resize_volume()
+    - ubifs: Fix memory leak in alloc_wbufs()
+    - ubi: Fix possible null-ptr-deref in ubi_free_volume()
+    - ubifs: Re-statistic cleaned znode count if commit failed
+    - ubifs: ubifs_writepage: Mark page dirty after writing inode failed
+    - ubi: fastmap: Fix missed fm_anchor PEB in wear-leveling after disabling
+      fastmap
+    - ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
+    - ubi: ubi_wl_put_peb: Fix infinite loop when wear-leveling work failed
+    - f2fs: fix to avoid potential memory corruption in __update_iostat_latency()
+    - ext4: use ext4_fc_tl_mem in fast-commit replay path
+    - netfilter: nf_tables: allow to fetch set elements when table has an owner
+    - x86: um: vdso: Add '%rcx' and '%r11' to the syscall clobber list
+    - um: virtio_uml: free command if adding to virtqueue failed
+    - um: virtio_uml: mark device as unregistered when breaking it
+    - um: virtio_uml: move device breaking into workqueue
+    - um: virt-pci: properly remove PCI device from bus
+    - watchdog: at91sam9_wdt: use devm_request_irq to avoid missing free_irq() in
+      error path
+    - watchdog: Fix kmemleak in watchdog_cdev_register
+    - watchdog: pcwd_usb: Fix attempting to access uninitialized memory
+    - watchdog: sbsa_wdog: Make sure the timeout programming is within the limits
+    - netfilter: ctnetlink: fix possible refcount leak in
+      ctnetlink_create_conntrack()
+    - netfilter: ebtables: fix table blob use-after-free
+    - netfilter: x_tables: fix percpu counter block leak on error path when
+      creating new netns
+    - ipv6: Add lwtunnel encap size of all siblings in nexthop calculation
+    - sctp: add a refcnt in sctp_stream_priorities to avoid a nested loop
+    - octeontx2-pf: Use correct struct reference in test condition
+    - net: fix __dev_kfree_skb_any() vs drop monitor
+    - 9p/xen: fix version parsing
+    - 9p/xen: fix connection sequence
+    - 9p/rdma: unmap receive dma buffer in rdma_request()/post_recv()
+    - net/mlx5e: Verify flow_source cap before using it
+    - net/mlx5: Geneve, Fix handling of Geneve object id as error code
+    - nfc: fix memory leak of se_io context in nfc_genl_se_io
+    - net/sched: transition act_pedit to rcu and percpu stats
+    - net/sched: act_pedit: fix action bind logic
+    - net/sched: act_mpls: fix action bind logic
+    - net/sched: act_sample: fix action bind logic
+    - ARM: dts: spear320-hmi: correct STMPE GPIO compatible
+    - tcp: tcp_check_req() can be called from process context
+    - vc_screen: modify vcs_size() handling in vcs_read()
+    - rtc: sun6i: Always export the internal oscillator
+    - genirq: Refactor accessors to use irq_data_get_affinity_mask
+    - genirq: Add and use an irq_data_update_affinity helper
+    - scsi: ipr: Work around fortify-string warning
+    - rtc: allow rtc_read_alarm without read_alarm callback
+    - loop: loop_set_status_from_info() check before assignment
+    - ASoC: adau7118: don't disable regulators on device unbind
+    - ASoC: zl38060: Remove spurious gpiolib select
+    - ASoC: zl38060 add gpiolib dependency
+    - ASoC: mediatek: mt8195: add missing initialization
+    - thermal: intel: quark_dts: fix error pointer dereference
+    - thermal: intel: BXT_PMIC: select REGMAP instead of depending on it
+    - tracing: Add NULL checks for buffer in ring_buffer_free_read_page()
+    - kernel/printk/index.c: fix memory leak with using debugfs_lookup()
+    - firmware/efi sysfb_efi: Add quirk for Lenovo IdeaPad Duet 3
+    - bootconfig: Increase max nodes of bootconfig from 1024 to 8192 for DCC
+      support
+    - mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
+    - IB/hfi1: Update RMT size calculation
+    - iommu/amd: Fix error handling for pdev_pri_ats_enable()
+    - media: uvcvideo: Remove format descriptions
+    - media: uvcvideo: Handle cameras with invalid descriptors
+    - media: uvcvideo: Handle errors from calls to usb_string
+    - media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910
+    - media: uvcvideo: Silence memcpy() run-time false positive warnings
+    - USB: fix memory leak with using debugfs_lookup()
+    - staging: emxx_udc: Add checks for dma_alloc_coherent()
+    - tty: fix out-of-bounds access in tty_driver_lookup_tty()
+    - tty: serial: fsl_lpuart: disable the CTS when send break signal
+    - serial: sc16is7xx: setup GPIO controller later in probe
+    - mei: bus-fixup:upon error print return values of send and receive
+    - tools/iio/iio_utils:fix memory leak
+    - iio: accel: mma9551_core: Prevent uninitialized variable in
+      mma9551_read_status_word()
+    - iio: accel: mma9551_core: Prevent uninitialized variable in
+      mma9551_read_config_word()
+    - soundwire: bus_type: Avoid lockdep assert in sdw_drv_probe()
+    - PCI: loongson: Prevent LS7A MRRS increases
+    - USB: dwc3: fix memory leak with using debugfs_lookup()
+    - USB: chipidea: fix memory leak with using debugfs_lookup()
+    - USB: uhci: fix memory leak with using debugfs_lookup()
+    - USB: sl811: fix memory leak with using debugfs_lookup()
+    - USB: fotg210: fix memory leak with using debugfs_lookup()
+    - USB: isp116x: fix memory leak with using debugfs_lookup()
+    - USB: isp1362: fix memory leak with using debugfs_lookup()
+    - USB: gadget: gr_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: bcm63xx_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: lpc32xx_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: pxa25x_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: pxa27x_udc: fix memory leak with using debugfs_lookup()
+    - usb: host: xhci: mvebu: Iterate over array indexes instead of using pointer
+      math
+    - USB: ene_usb6250: Allocate enough memory for full object
+    - usb: uvc: Enumerate valid values for color matching
+    - usb: gadget: uvc: Make bSourceID read/write
+    - PCI: Align extra resources for hotplug bridges properly
+    - PCI: Take other bus devices into account when distributing resources
+    - tty: pcn_uart: fix memory leak with using debugfs_lookup()
+    - misc: vmw_balloon: fix memory leak with using debugfs_lookup()
+    - drivers: base: component: fix memory leak with using debugfs_lookup()
+    - drivers: base: dd: fix memory leak with using debugfs_lookup()
+    - kernel/fail_function: fix memory leak with using debugfs_lookup()
+    - PCI: loongson: Add more devices that need MRRS quirk
+    - PCI: Add ACS quirk for Wangxun NICs
+    - phy: rockchip-typec: Fix unsigned comparison with less than zero
+    - soundwire: cadence: Remove wasted space in response_buf
+    - soundwire: cadence: Drain the RX FIFO after an IO timeout
+    - net: tls: avoid hanging tasks on the tx_lock
+    - x86/resctl: fix scheduler confusion with 'current'
+    - drm/display/dp_mst: Fix down/up message handling after sink disconnect
+    - drm/display/dp_mst: Fix down message handling after a packet reception error
+    - Bluetooth: hci_sock: purge socket queues in the destruct() callback
+    - media: uvcvideo: Fix race condition with usb_kill_urb
+    - drm/virtio: Fix error code in virtio_gpu_object_shmem_init()
+    - Revert "scsi: mpt3sas: Fix return value check of dma_get_required_mask()"
+    - scsi: mpt3sas: Don't change DMA mask while reallocating pools
+    - scsi: mpt3sas: re-do lost mpt3sas DMA mask fix
+    - scsi: mpt3sas: Remove usage of dma_get_required_mask() API
+    - malidp: Fix NULL vs IS_ERR() checking
+    - usb: gadget: uvc: fix missing mutex_unlock() if kstrtou8() fails
+    - Linux 5.15.100
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] update annotations scripts
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Tue, 31 Oct 2023 09:57:14 +1000
+
+linux-xilinx-zynqmp (5.15.0-1023.27) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1023.27 -proposed tracker (LP: #2025252)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+
+  * Miscellaneous upstream changes
+    - drivers:media Ar1335: Add MODULE DEVICE TABLE entry
+
+  [ Ubuntu: 5.15.0-76.83 ]
+
+  * jammy/linux: 5.15.0-76.83 -proposed tracker (LP: #2023905)
+  * cls_flower: off-by-one in fl_set_geneve_opt (LP: #2023577)
+    - net/sched: flower: fix possible OOB write in fl_set_geneve_opt()
+  * Some INVLPG implementations can leave Global translations unflushed when
+    PCIDs are enabled (LP: #2023220)
+    - x86/mm: Avoid incomplete Global INVLPG flushes
+
+  [ Ubuntu: 5.15.0-75.82 ]
+
+  * jammy/linux: 5.15.0-75.82 -proposed tracker (LP: #2023065)
+  * Jammy update: v5.15.102 upstream stable release (LP: #2020393)
+    - wifi: cfg80211: Partial revert "wifi: cfg80211: Fix use after free for wext"
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] resync getabis
+  * fix typo in config-checks invocation (LP: #2020413)
+    - [Packaging] fix typo when calling the old config-check
+    - [Packaging] fix typo in 4-checks.mk
+  * support python < 3.9 with annotations (LP: #2020531)
+    - [Packaging] kconfig/annotations.py: support older way of merging dicts
+
+ -- Wen-chien Jesse Sung <jesse.sung@canonical.com>  Wed, 28 Jun 2023 23:01:40 +0800
+
+linux-xilinx-zynqmp (5.15.0-1022.26) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1022.26 -proposed tracker (LP: #2019520)
+
+  * Use new annotations model (LP: #2019000)
+    - [Config] migrate zynqmp config into annotations
+
+  * Update k26 Linux device tree to pull in qspi partition layout changes
+    - arm64: zynqmp: Add mtd partition for secure OS storage area
+
+  * ap1302: add support for test pattern mode
+    - media: i2c: ap1302: Add test pattern control
+
+  * KR260 Device Tree Patch
+    - Added GEM TSU clock properties to KR260 PS GEMs
+
+  * KR260 PL eth ports causing kernel panic with kr07 image
+    - net: axienet: Remove repeated MDIO setup
+    - net: axienet: Remove repeated RX skb handling
+    - net: xilinx: Correct skb passed in error handling path
+
+  * mv-camera-sensor-module: Add support for Y10/Y12 formats
+    - mv-camera-sensor-module: Add support for Y10/Y12 formats
+
+  * Submit kernel patches for AR1335 driver
+    - media:i2c  AR1335 Camera sensor driver support
+    - media: dt-bindings: media: i2c: Add bindings for AR1335
+    - [Config] Enable AR1335 driver as a kernel module
+
+  * Update AMD TSN Preemption and minor bug fixes
+    - lib: add reference counting tracking infrastructure
+    - net: add net device refcount tracker infrastructure
+    - netlink: add net device refcount tracker to struct ethnl_req_info
+    - ethtool: use ethnl_parse_header_dev_put()
+    - net: ethtool: netlink: introduce ethnl_update_bool()
+    - net: ethtool: add support for MAC Merge layer
+    - docs: ethtool-netlink: document interface for MAC Merge layer
+    - net: ethtool: netlink: retrieve stats from multiple sources (eMAC, pMAC)
+    - docs: ethtool: document ETHTOOL_A_STATS_SRC and ETHTOOL_A_PAUSE_STATS_SRC
+    - net: ethtool: add helpers for aggregate statistics
+    - net: ethtool: add helpers for MM fragment size translation
+    - net: dsa: add plumbing for changing and getting MAC merge layer state
+    - net: ethtool: fix NULL pointer dereference in stats_prepare_data()
+    - net: ethtool: fix NULL pointer dereference in pause_prepare_data()
+    - net: ethtool: provide shims for stats aggregation helpers when
+      CONFIG_ETHTOOL_NETLINK=n
+    - ethtool: mm: fix get_mm() return code not propagating to user space
+    - net: ethtool: fix __ethtool_dev_mm_supported() implementation
+    - staging: xilinx-tsn: Add support to configure MAC merge parameters via
+      ethtool
+    - staging: xilinx-tsn: defer temac and switch probe when ep is not probed.
+    - staging: xilinx-tsn: don't exit probe when ep mac address is not found
+    - staging: xilinx-tsn: warn user when temac and ep mac address dont match
+
+  [ Ubuntu: 5.15.0-74.81 ]
+
+  * jammy/linux: 5.15.0-74.81 -proposed tracker (LP: #2019420)
+  * smartpqi: Update 22.04 driver to include recent bug fixes and support
+    current generation devices (LP: #1998643)
+    - scsi: smartpqi: Switch to attribute groups
+    - scsi: smartpqi: Fix rmmod stack trace
+    - scsi: smartpqi: Add PCI IDs
+    - scsi: smartpqi: Enable SATA NCQ priority in sysfs
+    - scsi: smartpqi: Eliminate drive spin down on warm boot
+    - scsi: smartpqi: Quickly propagate path failures to SCSI midlayer
+    - scsi: smartpqi: Fix a name typo and cleanup code
+    - scsi: smartpqi: Fix a typo in func pqi_aio_submit_io()
+    - scsi: smartpqi: Resolve delay issue with PQI_HZ value
+    - scsi: smartpqi: Avoid drive spin-down during suspend
+    - scsi: smartpqi: Update volume size after expansion
+    - scsi: smartpqi: Speed up RAID 10 sequential reads
+    - scsi: smartpqi: Expose SAS address for SATA drives
+    - scsi: smartpqi: Fix NUMA node not updated during init
+    - scsi: smartpqi: Fix BUILD_BUG_ON() statements
+    - scsi: smartpqi: Fix hibernate and suspend
+    - scsi: smartpqi: Fix lsscsi -t SAS addresses
+    - scsi: smartpqi: Update version to 2.1.14-035
+    - scsi: smartpqi: Fix unused variable pqi_pm_ops for clang
+    - scsi: smartpqi: Stop using the SCSI pointer
+    - scsi: smartpqi: Fix typo in comment
+    - scsi: smartpqi: Shorten drive visibility after removal
+    - scsi: smartpqi: Add controller fw version to console log
+    - scsi: smartpqi: Add PCI IDs for ramaxel controllers
+    - scsi: smartpqi: Close write read holes
+    - scsi: smartpqi: Add driver support for multi-LUN devices
+    - scsi: smartpqi: Fix PCI control linkdown system hang
+    - scsi: smartpqi: Add PCI ID for Adaptec SmartHBA 2100-8i
+    - scsi: smartpqi: Add PCI IDs for Lenovo controllers
+    - scsi: smartpqi: Stop logging spurious PQI reset failures
+    - scsi: smartpqi: Fix RAID map race condition
+    - scsi: smartpqi: Add module param to disable managed ints
+    - scsi: smartpqi: Update deleting a LUN via sysfs
+    - scsi: smartpqi: Add ctrl ready timeout module parameter
+    - scsi: smartpqi: Update copyright to current year
+    - scsi: smartpqi: Update version to 2.1.18-045
+    - scsi: smartpqi: Convert to host_tagset
+    - scsi: smartpqi: Add new controller PCI IDs
+    - scsi: smartpqi: Correct max LUN number
+    - scsi: smartpqi: Change sysfs raid_level attribute to N/A for controllers
+    - scsi: smartpqi: Correct device removal for multi-actuator devices
+    - scsi: smartpqi: Add controller cache flush during rmmod
+    - scsi: smartpqi: Initialize feature section info
+    - scsi: smartpqi: Change version to 2.1.20-035
+  * CVE-2023-32233
+    - netfilter: nf_tables: deactivate anonymous set from preparation phase
+  * CVE-2023-2612
+    - SAUCE: shiftfs: prevent lock unbalance in shiftfs_create_object()
+  * CVE-2023-31436
+    - net: sched: sch_qfq: prevent slab-out-of-bounds in qfq_activate_agg
+  * CVE-2023-1380
+    - wifi: brcmfmac: slab-out-of-bounds read in brcmf_get_assoc_ies()
+  * Add  PPIN support for Intel EMR cpu (LP: #2019131)
+    - x86/cpu: Merge Intel and AMD ppin_init() functions
+    - x86/cpu: Add Xeon Emerald Rapids to list of CPUs that support PPIN
+  * conntrack mark is not advertised via netlink (LP: #2016269)
+    - netfilter: ctnetlink: revert to dumping mark regardless of event type
+  * [SRU] Backport request for hpwdt from upstream 6.1 to Jammy (LP: #2008751)
+    - watchdog/hpwdt: Enable HP_WATCHDOG for ARM64 systems.
+    - watchdog/hpwdt: Include nmi.h only if CONFIG_HPWDT_NMI_DECODING
+    - [Config] Add arm64 option to CONFIG_HP_WATCHDOG
+  * Ubuntu 22.04 raise abnormal NIC MSI-X requests with larger CPU cores (256)
+    (LP: #2012335)
+    - ice: Allow operation with reduced device MSI-X
+  * Dell: Enable speaker mute hotkey LED indicator (LP: #2015972)
+    - platform/x86: dell-laptop: Register ctl-led for speaker-mute
+  * [SRU]With "Performance per Watt (DAPC)" enabled in the BIOS, Bootup time is
+    taking longer than expected (LP: #2008527)
+    - cpufreq: ACPI: Defer setting boost MSRs
+  * [SRU][Jammy] CONFIG_PCI_MESON is not enabled (LP: #2007745)
+    - [Config] arm64: Enable PCI_MESON module
+  * Jammy update: v5.15.99 upstream stable release (LP: #2018438)
+    - HID: asus: use spinlock to protect concurrent accesses
+    - HID: asus: use spinlock to safely schedule workers
+    - powerpc/mm: Rearrange if-else block to avoid clang warning
+    - ARM: OMAP2+: Fix memory leak in realtime_counter_init()
+    - arm64: dts: qcom: qcs404: use symbol names for PCIe resets
+    - arm64: dts: qcom: msm8996-tone: Fix USB taking 6 minutes to wake up
+    - arm64: dts: qcom: sm8150-kumano: Panel framebuffer is 2.5k instead of 4k
+    - arm64: dts: qcom: sm6125: Reorder HSUSB PHY clocks to match bindings
+    - arm64: dts: imx8m: Align SoC unique ID node unit address
+    - ARM: zynq: Fix refcount leak in zynq_early_slcr_init
+    - arm64: dts: mediatek: mt8183: Fix systimer 13 MHz clock description
+    - arm64: dts: qcom: sdm845-db845c: fix audio codec interrupt pin name
+    - arm64: dts: qcom: sc7180: correct SPMI bus address cells
+    - arm64: dts: qcom: sc7280: correct SPMI bus address cells
+    - arm64: dts: meson-gx: Fix Ethernet MAC address unit name
+    - arm64: dts: meson-g12a: Fix internal Ethernet PHY unit name
+    - arm64: dts: meson-gx: Fix the SCPI DVFS node name and unit address
+    - arm64: dts: msm8992-bullhead: add memory hole region
+    - arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem size
+    - arm64: dts: qcom: msm8992-bullhead: Disable dfps_data_mem
+    - arm64: dts: qcom: ipq8074: correct USB3 QMP PHY-s clock output names
+    - arm64: dts: qcom: Fix IPQ8074 PCIe PHY nodes
+    - arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
+    - arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY
+    - arm64: dts: qcom: ipq8074: correct Gen2 PCIe ranges
+    - arm64: dts: qcom: ipq8074: fix Gen3 PCIe node
+    - arm64: dts: qcom: ipq8074: correct PCIe QMP PHY output clock names
+    - arm64: dts: meson: remove CPU opps below 1GHz for G12A boards
+    - ARM: OMAP1: call platform_device_put() in error case in
+      omap1_dm_timer_init()
+    - ARM: bcm2835_defconfig: Enable the framebuffer
+    - ARM: s3c: fix s3c64xx_set_timer_source prototype
+    - arm64: dts: ti: k3-j7200: Fix wakeup pinmux range
+    - ARM: dts: exynos: correct wr-active property in Exynos3250 Rinato
+    - ARM: imx: Call ida_simple_remove() for ida_simple_get
+    - arm64: dts: amlogic: meson-gx: fix SCPI clock dvfs node name
+    - arm64: dts: amlogic: meson-axg: fix SCPI clock dvfs node name
+    - arm64: dts: amlogic: meson-gx: add missing SCPI sensors compatible
+    - arm64: dts: amlogic: meson-gxl-s905d-sml5442tw: drop invalid clock-names
+      property
+    - arm64: dts: amlogic: meson-gx: add missing unit address to rng node name
+    - arm64: dts: amlogic: meson-gxl: add missing unit address to eth-phy-mux node
+      name
+    - arm64: dts: amlogic: meson-gx-libretech-pc: fix update button name
+    - arm64: dts: amlogic: meson-sm1-bananapi-m5: fix adc keys node names
+    - arm64: dts: amlogic: meson-gxl-s905d-phicomm-n1: fix led node name
+    - arm64: dts: amlogic: meson-gxbb-kii-pro: fix led node name
+    - arm64: dts: amlogic: meson-sm1-odroid-hc4: fix active fan thermal trip
+    - locking/rwsem: Optimize down_read_trylock() under highly contended case
+    - locking/rwsem: Disable preemption in all down_read*() and up_read() code
+      paths
+    - arm64: dts: renesas: beacon-renesom: Fix gpio expander reference
+    - arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
+    - ARM: dts: sun8i: nanopi-duo2: Fix regulator GPIO reference
+    - ARM: dts: imx7s: correct iomuxc gpr mux controller cells
+    - arm64: dts: mt8192: Fix CPU map for single-cluster SoC
+    - arm64: dts: mediatek: mt7622: Add missing pwm-cells to pwm node
+    - blk-mq: avoid sleep in blk_mq_alloc_request_hctx
+    - blk-mq: remove stale comment for blk_mq_sched_mark_restart_hctx
+    - blk-mq: correct stale comment of .get_budget
+    - arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM
+      and MPSS memory regions
+    - s390/dasd: Fix potential memleak in dasd_eckd_init()
+    - sched/deadline,rt: Remove unused parameter from pick_next_[rt|dl]_entity()
+    - sched/rt: pick_next_rt_entity(): check list_entry
+    - x86/perf/zhaoxin: Add stepping check for ZXC
+    - KEYS: asymmetric: Fix ECDSA use via keyctl uapi
+    - arm64: dts: qcom: pmk8350: Specify PBS register for PON
+    - arm64: dts: qcom: pmk8350: Use the correct PON compatible
+    - block: bio-integrity: Copy flags when bio_integrity_payload is cloned
+    - wifi: rsi: Fix memory leak in rsi_coex_attach()
+    - wifi: rtlwifi: rtl8821ae: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: rtl8188ee: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: rtl8723be: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: iwlegacy: common: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: fix memory leak in lbs_init_adapter()
+    - wifi: rtl8xxxu: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: Fix global-out-of-bounds bug in
+      _rtl8812ae_phy_set_txpower_limit()
+    - libbpf: Fix btf__align_of() by taking into account field offsets
+    - wifi: ipw2x00: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: ipw2200: fix memory leak in ipw_wdev_init()
+    - wifi: wilc1000: fix potential memory leak in wilc_mac_xmit()
+    - wifi: brcmfmac: fix potential memory leak in brcmf_netdev_start_xmit()
+    - wifi: brcmfmac: unmap dma buffer in brcmf_msgbuf_alloc_pktid()
+    - wifi: libertas_tf: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: if_usb: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: main: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: cmdresp: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: wl3501_cs: don't call kfree_skb() under spin_lock_irqsave()
+    - crypto: x86/ghash - fix unaligned access in ghash_setkey()
+    - ACPICA: Drop port I/O validation for some regions
+    - genirq: Fix the return type of kstat_cpu_irqs_sum()
+    - rcu-tasks: Improve comments explaining tasks_rcu_exit_srcu purpose
+    - rcu-tasks: Remove preemption disablement around srcu_read_[un]lock() calls
+    - rcu-tasks: Fix synchronize_rcu_tasks() VS zap_pid_ns_processes()
+    - lib/mpi: Fix buffer overrun when SG is too long
+    - crypto: ccp - Avoid page allocation failure warning for SEV_GET_ID2
+    - ACPICA: nsrepair: handle cases without a return value correctly
+    - thermal/drivers/tsens: Drop msm8976-specific defines
+    - thermal/drivers/tsens: Add compat string for the qcom,msm8960
+    - thermal/drivers/tsens: Sort out msm8976 vs msm8956 data
+    - thermal/drivers/tsens: fix slope values for msm8939
+    - thermal/drivers/tsens: limit num_sensors to 9 for msm8939
+    - wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
+    - wifi: orinoco: check return value of hermes_write_wordrec()
+    - wifi: ath9k: htc_hst: free skb in ath9k_htc_rx_msg() if there is no callback
+      function
+    - ath9k: hif_usb: simplify if-if to if-else
+    - ath9k: htc: clean up statistics macros
+    - wifi: ath9k: hif_usb: clean up skbs if ath9k_hif_usb_rx_stream() fails
+    - wifi: ath9k: Fix potential stack-out-of-bounds write in
+      ath9k_wmi_rsp_callback()
+    - wifi: ath11k: Fix memory leak in ath11k_peer_rx_frag_setup
+    - wifi: cfg80211: Fix extended KCK key length check in
+      nl80211_set_rekey_data()
+    - ACPI: battery: Fix missing NUL-termination with large strings
+    - crypto: ccp - Failure on re-initialization due to duplicate sysfs filename
+    - crypto: essiv - Handle EBUSY correctly
+    - crypto: seqiv - Handle EBUSY correctly
+    - powercap: fix possible name leak in powercap_register_zone()
+    - x86: Mark stop_this_cpu() __noreturn
+    - x86/microcode: Rip out the OLD_INTERFACE
+    - [Config] Drop MICROCODE_OLD_INTERFACE
+    - x86/microcode: Default-disable late loading
+    - x86/microcode: Print previous version of microcode after reload
+    - x86/microcode: Add a parameter to microcode_check() to store CPU
+      capabilities
+    - x86/microcode: Check CPU capabilities after late microcode update correctly
+    - x86/microcode: Adjust late loading result reporting message
+    - crypto: xts - Handle EBUSY correctly
+    - leds: led-class: Add missing put_device() to led_put()
+    - crypto: ccp - Refactor out sev_fw_alloc()
+    - crypto: ccp - Flush the SEV-ES TMR memory before giving it to firmware
+    - bpftool: profile online CPUs instead of possible
+    - mt76: mt7915: fix polling firmware-own status
+    - net/mlx5: Enhance debug print in page allocation failure
+    - irqchip: Fix refcount leak in platform_irqchip_probe
+    - irqchip/alpine-msi: Fix refcount leak in alpine_msix_init_domains
+    - irqchip/irq-mvebu-gicp: Fix refcount leak in mvebu_gicp_probe
+    - irqchip/ti-sci: Fix refcount leak in ti_sci_intr_irq_domain_probe
+    - s390/mem_detect: fix detect_memory() error handling
+    - s390/vmem: fix empty page tables cleanup under KASAN
+    - net: add sock_init_data_uid()
+    - tun: tun_chr_open(): correctly initialize socket uid
+    - tap: tap_open(): correctly initialize socket uid
+    - OPP: fix error checking in opp_migrate_dentry()
+    - Bluetooth: L2CAP: Fix potential user-after-free
+    - Bluetooth: hci_qca: get wakeup status from serdev device handle
+    - s390/ap: fix status returned by ap_aqic()
+    - s390/ap: fix status returned by ap_qact()
+    - libbpf: Fix alen calculation in libbpf_nla_dump_errormsg()
+    - rds: rds_rm_zerocopy_callback() correct order for list_add_tail()
+    - crypto: rsa-pkcs1pad - Use akcipher_request_complete
+    - m68k: /proc/hardware should depend on PROC_FS
+    - RISC-V: time: initialize hrtimer based broadcast clock event device
+    - wifi: iwl3945: Add missing check for create_singlethread_workqueue
+    - wifi: iwl4965: Add missing check for create_singlethread_workqueue()
+    - wifi: mwifiex: fix loop iterator in mwifiex_update_ampdu_txwinsize()
+    - selftests/bpf: Fix out-of-srctree build
+    - ACPI: resource: Add IRQ overrides for MAINGEAR Vector Pro 2 models
+    - ACPI: resource: Do IRQ override on all TongFang GMxRGxx
+    - crypto: crypto4xx - Call dma_unmap_page when done
+    - wifi: mac80211: make rate u32 in sta_set_rate_info_rx()
+    - thermal/drivers/hisi: Drop second sensor hi3660
+    - can: esd_usb: Move mislocated storage of SJA1000_ECC_SEG bits in case of a
+      bus error
+    - bpf: Fix global subprog context argument resolution logic
+    - irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts
+    - irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts
+    - selftests/net: Interpret UDP_GRO cmsg data as an int value
+    - l2tp: Avoid possible recursive deadlock in l2tp_tunnel_register()
+    - net: bcmgenet: fix MoCA LED control
+    - sefltests: netdevsim: wait for devlink instance after netns removal
+    - drm: Fix potential null-ptr-deref due to drmm_mode_config_init()
+    - drm/fourcc: Add missing big-endian XRGB1555 and RGB565 formats
+    - drm/bridge: ti-sn65dsi83: Fix delay after reset deassert to match spec
+    - drm: mxsfb: DRM_MXSFB should depend on ARCH_MXS || ARCH_MXC
+    - [Config] Drop DRM_MXSFB for armhf-generic-lpae
+    - drm/bridge: megachips: Fix error handling in i2c_register_driver()
+    - drm/vkms: Fix memory leak in vkms_init()
+    - drm/vkms: Fix null-ptr-deref in vkms_release()
+    - drm/vc4: dpi: Add option for inverting pixel clock and output enable
+    - drm/vc4: dpi: Fix format mapping for RGB565
+    - drm: tidss: Fix pixel format definition
+    - gpu: ipu-v3: common: Add of_node_put() for reference returned by
+      of_graph_get_port_by_id()
+    - hwmon: (ftsteutates) Fix scaling of measurements
+    - drm/msm/hdmi: Add missing check for alloc_ordered_workqueue
+    - pinctrl: qcom: pinctrl-msm8976: Correct function names for wcss pins
+    - pinctrl: stm32: Fix refcount leak in stm32_pctrl_get_irq_domain
+    - pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
+    - drm/vc4: hvs: Set AXI panic modes
+    - drm/vc4: hvs: Fix colour order for xRGB1555 on HVS5
+    - drm/vc4: hdmi: Correct interlaced timings again
+    - drm/msm: clean event_thread->worker in case of an error
+    - scsi: qla2xxx: edif: Fix I/O timeout due to over-subscription
+    - scsi: qla2xxx: Fix exchange oversubscription
+    - scsi: qla2xxx: Fix exchange oversubscription for management commands
+    - ASoC: fsl_sai: Update to modern clocking terminology
+    - ASoC: fsl_sai: initialize is_dsp_mode flag
+    - drm/msm/adreno: Fix null ptr access in adreno_gpu_cleanup()
+    - ALSA: hda/ca0132: minor fix for allocation size
+    - drm/msm/gem: Add check for kmalloc
+    - drm/msm/dpu: Disallow unallocated resources to be returned
+    - drm/bridge: lt9611: fix sleep mode setup
+    - drm/bridge: lt9611: fix HPD reenablement
+    - drm/bridge: lt9611: fix polarity programming
+    - drm/bridge: lt9611: fix programming of video modes
+    - drm/bridge: lt9611: fix clock calculation
+    - drm/bridge: lt9611: pass a pointer to the of node
+    - drm/mipi-dsi: Fix byte order of 16-bit DCS set/get brightness
+    - drm: exynos: dsi: Fix MIPI_DSI*_NO_* mode flags
+    - drm/msm/dsi: Allow 2 CTRLs on v2.5.0
+    - drm/msm: use strscpy instead of strncpy
+    - drm/msm/dpu: Add check for cstate
+    - drm/msm/dpu: Add check for pstates
+    - drm/msm/mdp5: Add check for kzalloc
+    - pinctrl: bcm2835: Remove of_node_put() in bcm2835_of_gpio_ranges_fallback()
+    - pinctrl: mediatek: fix coding style
+    - pinctrl: mediatek: Initialize variable pullen and pullup to zero
+    - pinctrl: mediatek: Initialize variable *buf to zero
+    - gpu: host1x: Don't skip assigning syncpoints to channels
+    - drm/tegra: firewall: Check for is_addr_reg existence in IMM check
+    - drm/msm/dpu: set pdpu->is_rt_pipe early in dpu_plane_sspp_atomic_update()
+    - drm/mediatek: dsi: Reduce the time of dsi from LP11 to sending cmd
+    - drm/mediatek: Use NULL instead of 0 for NULL pointer
+    - drm/mediatek: Drop unbalanced obj unref
+    - drm/mediatek: mtk_drm_crtc: Add checks for devm_kcalloc
+    - drm/mediatek: Clean dangling pointer on bind error path
+    - ASoC: soc-compress.c: fixup private_data on snd_soc_new_compress()
+    - gpio: vf610: connect GPIO label to dev name
+    - spi: dw_bt1: fix MUX_MMIO dependencies
+    - ASoC: mchp-spdifrx: fix controls which rely on rsr register
+    - ASoC: mchp-spdifrx: fix return value in case completion times out
+    - ASoC: mchp-spdifrx: fix controls that works with completion mechanism
+    - ASoC: mchp-spdifrx: disable all interrupts in mchp_spdifrx_dai_remove()
+    - ASoC: rsnd: fixup #endif position
+    - ASoC: mchp-spdifrx: Fix uninitialized use of mr in mchp_spdifrx_hw_params()
+    - ASoC: dt-bindings: meson: fix gx-card codec node regex
+    - hwmon: (ltc2945) Handle error case in ltc2945_value_store
+    - drm/amdgpu: fix enum odm_combine_mode mismatch
+    - scsi: mpt3sas: Fix a memory leak
+    - scsi: aic94xx: Add missing check for dma_map_single()
+    - HID: multitouch: Add quirks for flipped axes
+    - HID: retain initial quirks set up when creating HID devices
+    - ASoC: codecs: Change bulk clock voting to optional voting in digital codecs
+    - ASoC: codecs: rx-macro: move clk provider to managed variants
+    - ASoC: codecs: tx-macro: move clk provider to managed variants
+    - ASoC: codecs: rx-macro: move to individual clks from bulk
+    - ASoC: codecs: tx-macro: move to individual clks from bulk
+    - ASoC: codecs: lpass: fix incorrect mclk rate
+    - spi: bcm63xx-hsspi: Fix multi-bit mode setting
+    - hwmon: (mlxreg-fan) Return zero speed for broken fan
+    - ASoC: tlv320adcx140: fix 'ti,gpio-config' DT property init
+    - dm: remove flush_scheduled_work() during local_exit()
+    - NFSv4: keep state manager thread active if swap is enabled
+    - nfs4trace: fix state manager flag printing
+    - NFS: fix disabling of swap
+    - spi: synquacer: Fix timeout handling in synquacer_spi_transfer_one()
+    - ASoC: soc-dapm.h: fixup warning struct snd_pcm_substream not declared
+    - HID: bigben: use spinlock to protect concurrent accesses
+    - HID: bigben_worker() remove unneeded check on report_field
+    - HID: bigben: use spinlock to safely schedule workers
+    - hid: bigben_probe(): validate report count
+    - drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
+    - nfsd: fix race to check ls_layouts
+    - cifs: Fix lost destroy smbd connection when MR allocate failed
+    - cifs: Fix warning and UAF when destroy the MR list
+    - gfs2: jdata writepage fix
+    - perf llvm: Fix inadvertent file creation
+    - leds: led-core: Fix refcount leak in of_led_get()
+    - perf inject: Use perf_data__read() for auxtrace
+    - perf intel-pt: Add documentation for Event Trace and TNT disable
+    - perf intel-pt: Add link to the perf wiki's Intel PT page
+    - perf intel-pt: Add support for emulated ptwrite
+    - perf intel-pt: Do not try to queue auxtrace data on pipe
+    - perf tools: Fix auto-complete on aarch64
+    - sparc: allow PM configs for sparc32 COMPILE_TEST
+    - printf: fix errname.c list
+    - objtool: add UACCESS exceptions for __tsan_volatile_read/write
+    - mfd: cs5535: Don't build on UML
+    - mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
+    - dmaengine: idxd: Set traffic class values in GRPCFG on DSA 2.0
+    - dmaengine: HISI_DMA should depend on ARCH_HISI
+    - [Config] Add HISI_DMA=n for armhf
+    - iio: light: tsl2563: Do not hardcode interrupt trigger type
+    - usb: gadget: fusb300_udc: free irq on the error path in fusb300_probe()
+    - i2c: designware: fix i2c_dw_clk_rate() return size to be u32
+    - soundwire: cadence: Don't overflow the command FIFOs
+    - driver core: fix potential null-ptr-deref in device_add()
+    - kobject: modify kobject_get_path() to take a const *
+    - kobject: Fix slab-out-of-bounds in fill_kobj_path()
+    - alpha/boot/tools/objstrip: fix the check for ELF header
+    - media: uvcvideo: Do not check for V4L2_CTRL_WHICH_DEF_VAL
+    - media: uvcvideo: Remove s_ctrl and g_ctrl
+    - media: uvcvideo: refactor __uvc_ctrl_add_mapping
+    - media: uvcvideo: Add support for V4L2_CTRL_TYPE_CTRL_CLASS
+    - media: uvcvideo: Use control names from framework
+    - media: uvcvideo: Check controls flags before accessing them
+    - media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()
+    - coresight: etm4x: Fix accesses to TRCSEQRSTEVR and TRCSEQSTR
+    - coresight: cti: Prevent negative values of enable count
+    - coresight: cti: Add PM runtime call in enable_store
+    - ACPI: resource: Add helper function acpi_dev_get_memory_resources()
+    - usb: typec: intel_pmc_mux: Use the helper acpi_dev_get_memory_resources()
+    - usb: typec: intel_pmc_mux: Don't leak the ACPI device reference count
+    - PCI/IOV: Enlarge virtfn sysfs name buffer
+    - PCI: switchtec: Return -EFAULT for copy_to_user() errors
+    - tty: serial: fsl_lpuart: disable Rx/Tx DMA in lpuart32_shutdown()
+    - tty: serial: fsl_lpuart: clear LPUART Status Register in lpuart32_shutdown()
+    - serial: tegra: Add missing clk_disable_unprepare() in tegra_uart_hw_init()
+    - Revert "char: pcmcia: cm4000_cs: Replace mdelay with usleep_range in
+      set_protocol"
+    - eeprom: idt_89hpesx: Fix error handling in idt_init()
+    - applicom: Fix PCI device refcount leak in applicom_init()
+    - firmware: stratix10-svc: add missing gen_pool_destroy() in
+      stratix10_svc_drv_probe()
+    - VMCI: check context->notify_page after call to get_user_pages_fast() to
+      avoid GPF
+    - misc/mei/hdcp: Use correct macros to initialize uuid_le
+    - driver core: fix resource leak in device_add()
+    - drivers: base: transport_class: fix possible memory leak
+    - drivers: base: transport_class: fix resource leak when
+      transport_add_device() fails
+    - firmware: dmi-sysfs: Fix null-ptr-deref in dmi_sysfs_register_handle
+    - fotg210-udc: Add missing completion handler
+    - dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
+    - usb: early: xhci-dbc: Fix a potential out-of-bound memory access
+    - tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case
+    - RDMA/cxgb4: add null-ptr-check after ip_dev_find()
+    - usb: musb: mediatek: don't unregister something that wasn't registered
+    - usb: gadget: configfs: use to_config_usb_cfg() in os_desc_link()
+    - usb: gadget: configfs: use to_usb_function_instance() in cfg (un)link func
+    - usb: gadget: configfs: remove using list iterator after loop body as a ptr
+    - usb: gadget: configfs: Restrict symlink creation is UDC already binded
+    - iommu/vt-d: Set No Execute Enable bit in PASID table entry
+    - power: supply: remove faulty cooling logic
+    - RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish()
+    - usb: max-3421: Fix setting of I/O pins
+    - RDMA/irdma: Cap MSIX used to online CPUs + 1
+    - serial: fsl_lpuart: fix RS485 RTS polariy inverse issue
+    - tty: serial: imx: Handle RS485 DE signal active high
+    - tty: serial: imx: disable Ageing Timer interrupt request irq
+    - dmaengine: dw-edma: Fix readq_ch() return value truncation
+    - phy: rockchip-typec: fix tcphy_get_mode error case
+    - iw_cxgb4: Fix potential NULL dereference in c4iw_fill_res_cm_id_entry()
+    - iommu: Fix error unwind in iommu_group_alloc()
+    - dmaengine: sf-pdma: pdma_desc memory leak fix
+    - dmaengine: dw-axi-dmac: Do not dereference NULL structure
+    - iommu/vt-d: Fix error handling in sva enable/disable paths
+    - iommu/vt-d: Remove duplicate identity domain flag
+    - iommu/vt-d: Check FL and SL capability sanity in scalable mode
+    - iommu/vt-d: Use second level for GPA->HPA translation
+    - iommu/vt-d: Allow to use flush-queue when first level is default
+    - IB/hfi1: Fix math bugs in hfi1_can_pin_pages()
+    - IB/hfi1: Fix sdma.h tx->num_descs off-by-one errors
+    - remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headers
+    - media: ti: cal: fix possible memory leak in cal_ctx_create()
+    - media: platform: ti: Add missing check for devm_regulator_get
+    - powerpc: Remove linker flag from KBUILD_AFLAGS
+    - s390/vdso: remove -nostdlib compiler flag
+    - s390/vdso: Drop '-shared' from KBUILD_CFLAGS_64
+    - builddeb: clean generated package content
+    - media: max9286: Fix memleak in max9286_v4l2_register()
+    - media: ov2740: Fix memleak in ov2740_init_controls()
+    - media: ov5675: Fix memleak in ov5675_init_controls()
+    - media: i2c: ov772x: Fix memleak in ov772x_probe()
+    - media: i2c: imx219: Split common registers from mode tables
+    - media: i2c: imx219: Fix binning for RAW8 capture
+    - media: v4l2-jpeg: correct the skip count in jpeg_parse_app14_data
+    - media: v4l2-jpeg: ignore the unknown APP14 marker
+    - media: imx-jpeg: Apply clk_bulk api instead of operating specific clk
+    - media: i2c: ov7670: 0 instead of -EINVAL was returned
+    - media: usb: siano: Fix use after free bugs caused by do_submit_urb
+    - media: saa7134: Use video_unregister_device for radio_dev
+    - rpmsg: glink: Avoid infinite loop on intent for missing channel
+    - udf: Define EFSCORRUPTED error code
+    - ARM: dts: exynos: Use Exynos5420 compatible for the MIPI video phy
+    - blk-iocost: fix divide by 0 error in calc_lcoefs()
+    - trace/blktrace: fix memory leak with using debugfs_lookup()
+    - wifi: ath9k: Fix use-after-free in ath9k_hif_usb_disconnect()
+    - wifi: brcmfmac: Fix potential stack-out-of-bounds in brcmf_c_preinit_dcmds()
+    - rcu: Make RCU_LOCKDEP_WARN() avoid early lockdep checks
+    - rcu: Suppress smp_processor_id() complaint in
+      synchronize_rcu_expedited_wait()
+    - rcu-tasks: Make rude RCU-Tasks work well with CPU hotplug
+    - wifi: ath11k: debugfs: fix to work with multiple PCI devices
+    - thermal: intel: Fix unsigned comparison with less than zero
+    - timers: Prevent union confusion from unexpected restart_syscall()
+    - x86/bugs: Reset speculation control settings on init
+    - wifi: brcmfmac: ensure CLM version is null-terminated to prevent stack-out-
+      of-bounds
+    - wifi: mt7601u: fix an integer underflow
+    - inet: fix fast path in __inet_hash_connect()
+    - ice: restrict PTP HW clock freq adjustments to 100, 000, 000 PPB
+    - ice: add missing checks for PF vsi type
+    - ACPI: Don't build ACPICA with '-Os'
+    - thermal: intel: intel_pch: Add support for Wellsburg PCH
+    - clocksource: Suspend the watchdog temporarily when high read latency
+      detected
+    - crypto: hisilicon: Wipe entire pool on error
+    - net: bcmgenet: Add a check for oversized packets
+    - m68k: Check syscall_trace_enter() return code
+    - netfilter: nf_tables: NULL pointer dereference in nf_tables_updobj()
+    - wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
+    - ACPI: video: Fix Lenovo Ideapad Z570 DMI match
+    - net/mlx5: fw_tracer: Fix debug print
+    - coda: Avoid partial allocation of sig_inputArgs
+    - uaccess: Add minimum bounds check on kernel buffer size
+    - s390/idle: mark arch_cpu_idle() noinstr
+    - time/debug: Fix memory leak with using debugfs_lookup()
+    - PM: domains: fix memory leak with using debugfs_lookup()
+    - PM: EM: fix memory leak with using debugfs_lookup()
+    - Bluetooth: btusb: Add VID:PID 13d3:3529 for Realtek RTL8821CE
+    - hv_netvsc: Check status in SEND_RNDIS_PKT completion message
+    - scm: add user copy checks to put_cmsg()
+    - drm/amd/display: Revert Reduce delay when sink device not able to ACK 00340h
+      write
+    - drm/amd/display: Fix potential null-deref in dm_resume
+    - drm/omap: dsi: Fix excessive stack usage
+    - HID: Add Mapping for System Microphone Mute
+    - drm/tiny: ili9486: Do not assume 8-bit only SPI controllers
+    - drm/radeon: free iio for atombios when driver shutdown
+    - scsi: lpfc: Fix use-after-free KFENCE violation during sysfs firmware write
+    - Revert "fbcon: don't lose the console font across generic->chip driver
+      switch"
+    - drm: amd: display: Fix memory leakage
+    - drm/msm/dsi: Add missing check for alloc_ordered_workqueue
+    - docs/scripts/gdb: add necessary make scripts_gdb step
+    - ASoC: soc-compress: Reposition and add pcm_mutex
+    - ASoC: kirkwood: Iterate over array indexes instead of using pointer math
+    - regulator: max77802: Bounds check regulator id against opmode
+    - regulator: s5m8767: Bounds check id indexing into arrays
+    - gfs2: Improve gfs2_make_fs_rw error handling
+    - hwmon: (coretemp) Simplify platform device handling
+    - pinctrl: at91: use devm_kasprintf() to avoid potential leaks
+    - scsi: snic: Fix memory leak with using debugfs_lookup()
+    - HID: logitech-hidpp: Don't restart communication if not necessary
+    - drm: panel-orientation-quirks: Add quirk for Lenovo IdeaPad Duet 3 10IGL5
+    - dm thin: add cond_resched() to various workqueue loops
+    - dm cache: add cond_resched() to various workqueue loops
+    - nfsd: zero out pointers after putting nfsd_files on COPY setup error
+    - drm/shmem-helper: Revert accidental non-GPL export
+    - wifi: rtl8xxxu: fixing transmisison failure for rtl8192eu
+    - firmware: coreboot: framebuffer: Ignore reserved pixel color bits
+    - block: don't allow multiple bios for IOCB_NOWAIT issue
+    - rtc: pm8xxx: fix set-alarm race
+    - ipmi:ssif: resend_msg() cannot fail
+    - ipmi_ssif: Rename idle state and check
+    - s390/extmem: return correct segment type in __segment_load()
+    - s390: discard .interp section
+    - s390/kprobes: fix irq mask clobbering on kprobe reenter from post_handler
+    - s390/kprobes: fix current_kprobe never cleared after kprobes reenter
+    - cifs: Fix uninitialized memory read in smb3_qfs_tcon()
+    - btrfs: hold block group refcount during async discard
+    - locking/rwsem: Prevent non-first waiter from spinning in down_write()
+      slowpath
+    - ksmbd: fix wrong data area length for smb2 lock request
+    - ksmbd: do not allow the actual frame length to be smaller than the rfc1002
+      length
+    - ARM: dts: exynos: correct HDMI phy compatible in Exynos4
+    - hfs: fix missing hfs_bnode_get() in __hfs_bnode_create
+    - fs: hfsplus: fix UAF issue in hfsplus_put_super
+    - exfat: fix reporting fs error when reading dir beyond EOF
+    - exfat: fix unexpected EOF while reading dir
+    - exfat: redefine DIR_DELETED as the bad cluster number
+    - exfat: fix inode->i_blocks for non-512 byte sector size device
+    - fs: dlm: don't set stop rx flag after node reset
+    - fs: dlm: move sending fin message into state change handling
+    - fs: dlm: send FIN ack back in right cases
+    - f2fs: fix information leak in f2fs_move_inline_dirents()
+    - f2fs: fix cgroup writeback accounting with fs-layer encryption
+    - ocfs2: fix defrag path triggering jbd2 ASSERT
+    - ocfs2: fix non-auto defrag path not working issue
+    - selftests/landlock: Skip overlayfs tests when not supported
+    - selftests/landlock: Test ptrace as much as possible with Yama
+    - udf: Truncate added extents on failed expansion
+    - udf: Do not bother merging very long extents
+    - udf: Do not update file length for failed writes to inline files
+    - udf: Preserve link count of system files
+    - udf: Detect system inodes linked into directory hierarchy
+    - udf: Fix file corruption when appending just after end of preallocated
+      extent
+    - RDMA/siw: Fix user page pinning accounting
+    - KVM: Destroy target device if coalesced MMIO unregistration fails
+    - KVM: x86: Inject #GP if WRMSR sets reserved bits in APIC Self-IPI
+    - KVM: SVM: Fix potential overflow in SEV's send|receive_update_data()
+    - KVM: SVM: hyper-v: placate modpost section mismatch error
+    - KVM: s390: disable migration mode when dirty tracking is disabled
+    - x86/virt: Force GIF=1 prior to disabling SVM (for reboot flows)
+    - x86/crash: Disable virt in core NMI crash handler to avoid double shootdown
+    - x86/reboot: Disable virtualization in an emergency if SVM is supported
+    - x86/reboot: Disable SVM, not just VMX, when stopping CPUs
+    - x86/kprobes: Fix __recover_optprobed_insn check optimizing logic
+    - x86/kprobes: Fix arch_check_optimized_kprobe check within optimized_kprobe
+      range
+    - x86/microcode/amd: Remove load_microcode_amd()'s bsp parameter
+    - x86/microcode/AMD: Add a @cpu parameter to the reloading functions
+    - x86/microcode/AMD: Fix mixed steppings support
+    - x86/speculation: Allow enabling STIBP with legacy IBRS
+    - Documentation/hw-vuln: Document the interaction between IBRS and STIBP
+    - brd: return 0/-error from brd_insert_page()
+    - ima: Align ima_file_mmap() parameters with mmap_file LSM hook
+    - irqdomain: Fix association race
+    - irqdomain: Fix disassociation race
+    - irqdomain: Look for existing mapping only once
+    - irqdomain: Drop bogus fwspec-mapping error handling
+    - irqdomain: Fix domain registration race
+    - crypto: qat - fix out-of-bounds read
+    - io_uring: handle TIF_NOTIFY_RESUME when checking for task_work
+    - io_uring: mark task TASK_RUNNING before handling resume/task work
+    - io_uring: add a conditional reschedule to the IOPOLL cancelation loop
+    - io_uring/rsrc: disallow multi-source reg buffers
+    - io_uring: remove MSG_NOSIGNAL from recvmsg
+    - io_uring/poll: allow some retries for poll triggering spuriously
+    - ALSA: ice1712: Do not left ice->gpio_mutex locked in aureon_add_controls()
+    - ALSA: hda/realtek: Add quirk for HP EliteDesk 800 G6 Tower PC
+    - jbd2: fix data missing when reusing bh which is ready to be checkpointed
+    - ext4: optimize ea_inode block expansion
+    - ext4: refuse to create ea block when umounted
+    - mtd: spi-nor: sfdp: Fix index value for SCCR dwords
+    - mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
+    - mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
+    - dm: send just one event on resize, not two
+    - dm: add cond_resched() to dm_wq_work()
+    - wifi: rtl8xxxu: Use a longer retry limit of 48
+    - wifi: ath11k: allow system suspend to survive ath11k
+    - wifi: cfg80211: Fix use after free for wext
+    - qede: fix interrupt coalescing configuration
+    - thermal: intel: powerclamp: Fix cur_state for multi package system
+    - dm flakey: fix logic when corrupting a bio
+    - dm flakey: don't corrupt the zero page
+    - dm flakey: fix a bug with 32-bit highmem systems
+    - ARM: dts: qcom: sdx55: Add Qcom SMMU-500 as the fallback for IOMMU node
+    - ARM: dts: exynos: correct TMU phandle in Exynos4210
+    - ARM: dts: exynos: correct TMU phandle in Exynos4
+    - ARM: dts: exynos: correct TMU phandle in Odroid XU3 family
+    - ARM: dts: exynos: correct TMU phandle in Exynos5250
+    - ARM: dts: exynos: correct TMU phandle in Odroid XU
+    - ARM: dts: exynos: correct TMU phandle in Odroid HC1
+    - fuse: add inode/permission checks to fileattr_get/fileattr_set
+    - rbd: avoid use-after-free in do_rbd_add() when rbd_dev_create() fails
+    - ceph: update the time stamps and try to drop the suid/sgid
+    - alpha: fix FEN fault handling
+    - dax/kmem: Fix leak of memory-hotplug resources
+    - mips: fix syscall_get_nr
+    - media: ipu3-cio2: Fix PM runtime usage_count in driver unbind
+    - remoteproc/mtk_scp: Move clk ops outside send_lock
+    - docs: gdbmacros: print newest record
+    - mm: memcontrol: deprecate charge moving
+    - mm/thp: check and bail out if page in deferred queue already
+    - ktest.pl: Give back console on Ctrt^C on monitor
+    - ktest.pl: Fix missing "end_monitor" when machine check fails
+    - ktest.pl: Add RUN_TIMEOUT option with default unlimited
+    - ring-buffer: Handle race between rb_move_tail and rb_check_pages
+    - tools/bootconfig: fix single & used for logical condition
+    - scsi: qla2xxx: Fix link failure in NPIV environment
+    - scsi: qla2xxx: Check if port is online before sending ELS
+    - scsi: qla2xxx: Fix DMA-API call trace on NVMe LS requests
+    - scsi: qla2xxx: Remove unintended flag clearing
+    - scsi: qla2xxx: Fix erroneous link down
+    - scsi: qla2xxx: Remove increment of interface err cnt
+    - scsi: ses: Don't attach if enclosure has no components
+    - scsi: ses: Fix slab-out-of-bounds in ses_enclosure_data_process()
+    - scsi: ses: Fix possible addl_desc_ptr out-of-bounds accesses
+    - scsi: ses: Fix possible desc_ptr out-of-bounds accesses
+    - scsi: ses: Fix slab-out-of-bounds in ses_intf_remove()
+    - RISC-V: add a spin_shadow_stack declaration
+    - riscv: mm: fix regression due to update_mmu_cache change
+    - riscv: jump_label: Fixup unaligned arch_static_branch function
+    - riscv, mm: Perform BPF exhandler fixup on page fault
+    - riscv: ftrace: Remove wasted nops for !RISCV_ISA_C
+    - riscv: ftrace: Reduce the detour code size to half
+    - MIPS: DTS: CI20: fix otg power gpio
+    - PCI/PM: Observe reset delay irrespective of bridge_d3
+    - PCI: hotplug: Allow marking devices as disconnected during bind/unbind
+    - PCI: Avoid FLR for AMD FCH AHCI adapters
+    - iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
+    - vfio/type1: prevent underflow of locked_vm via exec()
+    - vfio/type1: track locked_vm per dma
+    - vfio/type1: restore locked_vm
+    - drm/i915/quirks: Add inverted backlight quirk for HP 14-r206nv
+    - drm/radeon: Fix eDP for single-display iMac11,2
+    - drm/edid: fix AVI infoframe aspect ratio handling
+    - perf intel-pt: pkt-decoder: Add CFE and EVD packets
+    - qede: avoid uninitialized entries in coal_entry array
+    - media: uvcvideo: Fix memory leak of object map on error exit path
+    - iommu/vt-d: Fix an unbalanced rcu_read_lock/rcu_read_unlock()
+    - arm64: dts: qcom: ipq8074: fix Gen2 PCIe QMP PHY
+    - wifi: ath9k: use proper statements in conditionals
+    - kbuild: Port silent mode detection to future gnu make.
+    - Linux 5.15.99
+    - [Config] Stop expecting mxsfb for ppc64el
+  * Use new annotations model (LP: #2019000)
+    - [Packaging] new annotations model infrastructure
+    - [Config] migrate all configs into annotations
+  * CVE-2023-30456
+    - KVM: nVMX: add missing consistency checks for CR0 and CR4
+  * CVE-2023-1859
+    - 9p/xen : Fix use after free bug in xen_9pfs_front_remove due to race
+      condition
+  * CVE-2023-1670
+    - xirc2ps_cs: Fix use after free bug in xirc2ps_detach
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  [ Ubuntu: 5.15.0-72.79 ]
+
+  * jammy/linux: 5.15.0-72.79 -proposed tracker (LP: #2016548)
+  * Add split lock detection for EMR (LP: #2015855)
+    - x86/split_lock: Enumerate architectural split lock disable bit
+  *  selftest: fib_tests: Always cleanup before exit  (LP: #2015956)
+    - selftest: fib_tests: Always cleanup before exit
+  * Add support for intel EMR cpu (LP: #2015372)
+    - platform/x86: intel-uncore-freq: add Emerald Rapids support
+    - perf/x86/intel/cstate: Add Emerald Rapids
+    - perf/x86/rapl: Add support for Intel Emerald Rapids
+    - intel_idle: add Emerald Rapids Xeon support
+    - tools/power/x86/intel-speed-select: Add Emerald Rapid quirk
+    - tools/power turbostat: Introduce support for EMR
+    - powercap: intel_rapl: add support for Emerald Rapids
+    - EDAC/i10nm: Add Intel Emerald Rapids server support
+  * Kernel livepatch ftrace graph fix (LP: #2013603)
+    - kprobes: treewide: Remove trampoline_address from
+      kretprobe_trampoline_handler()
+    - kprobes: treewide: Make it harder to refer kretprobe_trampoline directly
+    - kprobes: Add kretprobe_find_ret_addr() for searching return address
+    - s390/unwind: recover kretprobe modified return address in stacktrace
+    - s390/unwind: fix fgraph return address recovery
+  * Jammy update: v5.15.98 upstream stable release (LP: #2015600)
+    - Linux 5.15.98
+  * Jammy update: v5.15.97 upstream stable release (LP: #2015599)
+    - ionic: refactor use of ionic_rx_fill()
+    - Fix XFRM-I support for nested ESP tunnels
+    - arm64: dts: rockchip: drop unused LED mode property from rk3328-roc-cc
+    - ARM: dts: rockchip: add power-domains property to dp node on rk3288
+    - HID: elecom: add support for TrackBall 056E:011C
+    - ACPI: NFIT: fix a potential deadlock during NFIT teardown
+    - btrfs: send: limit number of clones and allocated memory size
+    - ASoC: rt715-sdca: fix clock stop prepare timeout issue
+    - IB/hfi1: Assign npages earlier
+    - neigh: make sure used and confirmed times are valid
+    - HID: core: Fix deadloop in hid_apply_multiplier.
+    - x86/cpu: Add Lunar Lake M
+    - staging: mt7621-dts: change palmbus address to lower case
+    - bpf: bpf_fib_lookup should not return neigh in NUD_FAILED state
+    - net: Remove WARN_ON_ONCE(sk->sk_forward_alloc) from sk_stream_kill_queues().
+    - vc_screen: don't clobber return value in vcs_read
+    - scripts/tags.sh: Invoke 'realpath' via 'xargs'
+    - scripts/tags.sh: fix incompatibility with PCRE2
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-M
+    - USB: serial: option: add support for VW/Skoda "Carstick LTE"
+    - usb: gadget: u_serial: Add null pointer check in gserial_resume
+    - USB: core: Don't hold device lock while reading the "descriptors" sysfs file
+    - Linux 5.15.97
+  * Jammy update: v5.15.96 upstream stable release (LP: #2015595)
+    - drm/etnaviv: don't truncate physical page address
+    - wifi: rtl8xxxu: gen2: Turn on the rate control
+    - drm/edid: Fix minimum bpc supported with DSC1.2 for HDMI sink
+    - clk: mxl: Switch from direct readl/writel based IO to regmap based IO
+    - clk: mxl: Remove redundant spinlocks
+    - clk: mxl: Add option to override gate clks
+    - clk: mxl: Fix a clk entry by adding relevant flags
+    - powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
+    - clk: mxl: syscon_node_to_regmap() returns error pointers
+    - random: always mix cycle counter in add_latent_entropy()
+    - KVM: x86: Fail emulation during EMULTYPE_SKIP on any exception
+    - KVM: SVM: Skip WRMSR fastpath on VM-Exit if next RIP isn't valid
+    - can: kvaser_usb: hydra: help gcc-13 to figure out cmd_len
+    - powerpc: dts: t208x: Disable 10G on MAC1 and MAC2
+    - powerpc: use generic version of arch_is_kernel_initmem_freed()
+    - powerpc/vmlinux.lds: Ensure STRICT_ALIGN_SIZE is at least page aligned
+    - powerpc/vmlinux.lds: Add an explicit symbol for the SRWX boundary
+    - powerpc/64s/radix: Fix crash with unaligned relocated kernel
+    - powerpc/64s/radix: Fix RWX mapping with relocated kernel
+    - drm/i915/gvt: fix double free bug in split_2MB_gtt_entry
+    - uaccess: Add speculation barrier to copy_from_user()
+    - binder: read pre-translated fds from sender buffer
+    - binder: defer copies of pre-patched txn data
+    - binder: fix pointer cast warning
+    - binder: Address corner cases in deferred copy and fixup
+    - binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0
+    - nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
+    - wifi: mwifiex: Add missing compatible string for SD8787
+    - audit: update the mailing list in MAINTAINERS
+    - ext4: Fix function prototype mismatch for ext4_feat_ktype
+    - bpf: add missing header file include
+    - Linux 5.15.96
+  * Debian autoreconstruct Fix restoration of execute permissions (LP: #2015498)
+    - [Debian] autoreconstruct - fix restoration of execute permissions
+  * kernel: fix __clear_user() inline assembly constraints (LP: #2013088)
+    - s390/uaccess: add missing earlyclobber annotations to __clear_user()
+  * Kernel crash during Mellanox performance testing (LP: #2015097)
+    - net/mlx5: fs, refactor software deletion rule
+  * expoline.o is packaged unconditionally for s390x (LP: #2013209)
+    - [Packaging] Copy expoline.o only when produced by the build
+  * Intel E810 NICs driver in causing hangs when booting and bonds configured
+    (LP: #2004262)
+    - ice: avoid bonding causing auxiliary plug/unplug under RTNL lock
+  * Jammy update: v5.15.95 upstream stable release (LP: #2013118)
+    - mptcp: fix locking for in-kernel listener creation
+    - kprobes: treewide: Cleanup the error messages for kprobes
+    - riscv: kprobe: Fixup misaligned load text
+    - ACPI / x86: Add support for LPS0 callback handler
+    - ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
+    - ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
+    - selftests/bpf: Verify copy_register_state() preserves parent/live fields
+    - ALSA: hda: Do not unset preset when cleaning up codec
+    - bpf, sockmap: Don't let sock_map_{close,destroy,unhash} call itself
+    - ASoC: cs42l56: fix DT probe
+    - tools/virtio: fix the vringh test for virtio ring changes
+    - net/rose: Fix to not accept on connected socket
+    - net: stmmac: do not stop RX_CLK in Rx LPI state for qcs404 SoC
+    - drm/nouveau/devinit/tu102-: wait for GFW_BOOT_PROGRESS == COMPLETED
+    - net: sched: sch: Bounds check priority
+    - s390/decompressor: specify __decompress() buf len to avoid overflow
+    - nvme-fc: fix a missing queue put in nvmet_fc_ls_create_association
+    - drm/amd/display: Properly handle additional cases where DCN is not supported
+    - platform/x86: touchscreen_dmi: Add Chuwi Vi8 (CWI501) DMI match
+    - nvmem: core: add error handling for dev_set_name
+    - nvmem: core: fix cleanup after dev_set_name()
+    - nvmem: core: fix registration vs use race
+    - nvmem: core: fix return value
+    - xfs: zero inode fork buffer at allocation
+    - xfs: fix potential log item leak
+    - xfs: detect self referencing btree sibling pointers
+    - xfs: set XFS_FEAT_NLINK correctly
+    - xfs: validate v5 feature fields
+    - xfs: avoid unnecessary runtime sibling pointer endian conversions
+    - xfs: don't assert fail on perag references on teardown
+    - xfs: assert in xfs_btree_del_cursor should take into account error
+    - xfs: purge dquots after inode walk fails during quotacheck
+    - xfs: don't leak btree cursor when insrec fails after a split
+    - mptcp: do not wait for bare sockets' timeout
+    - aio: fix mremap after fork null-deref
+    - drm/amd/display: Fail atomic_check early on normalize_zpos error
+    - platform/x86: amd-pmc: Fix compilation when CONFIG_DEBUGFS is disabled
+    - platform/x86: amd-pmc: Correct usage of SMU version
+    - platform/x86/amd: pmc: Disable IRQ1 wakeup for RN/CZN
+    - netfilter: nft_tproxy: restrict to prerouting hook
+    - tcp: Fix listen() regression in 5.15.88.
+    - mmc: jz4740: Work around bug on JZ4760(B)
+    - mmc: sdio: fix possible resource leaks in some error paths
+    - mmc: mmc_spi: fix error handling in mmc_spi_probe()
+    - ALSA: hda/conexant: add a new hda codec SN6180
+    - ALSA: hda/realtek - fixed wrong gpio assigned
+    - sched/psi: Fix use-after-free in ep_remove_wait_queue()
+    - hugetlb: check for undefined shift on 32 bit architectures
+    - of: reserved_mem: Have kmemleak ignore dynamically allocated reserved mem
+    - selftest/lkdtm: Skip stack-entropy test if lkdtm is not available
+    - net: Fix unwanted sign extension in netdev_stats_to_stats64()
+    - revert "squashfs: harden sanity check in squashfs_read_xattr_id_table"
+    - ixgbe: allow to increase MTU to 3K with XDP enabled
+    - i40e: add double of VLAN header when computing the max MTU
+    - net: bgmac: fix BCM5358 support by setting correct flags
+    - net: ethernet: ti: am65-cpsw: Add RX DMA Channel Teardown Quirk
+    - sctp: sctp_sock_filter(): avoid list_entry() on possibly empty list
+    - dccp/tcp: Avoid negative sk_forward_alloc by ipv6_pinfo.pktoptions.
+    - net/usb: kalmia: Don't pass act_len in usb_bulk_msg error path
+    - net: openvswitch: fix possible memory leak in ovs_meter_cmd_set()
+    - net: stmmac: fix order of dwmac5 FlexPPS parametrization sequence
+    - bnxt_en: Fix mqprio and XDP ring checking logic
+    - net: stmmac: Restrict warning on disabling DMA store and fwd mode
+    - ixgbe: add double of VLAN header when computing the max MTU
+    - ipv6: Fix datagram socket connection with DSCP.
+    - ipv6: Fix tcp socket connection with DSCP.
+    - nilfs2: fix underflow in second superblock position calculations
+    - mm/filemap: fix page end in filemap_get_read_batch
+    - drm/i915/gen11: Moving WAs to icl_gt_workarounds_init()
+    - drm/i915/gen11: Wa_1408615072/Wa_1407596294 should be on GT list
+    - flow_offload: fill flags to action structure
+    - net/sched: act_ctinfo: use percpu stats
+    - i40e: Add checking for null for nlmsg_find_attr()
+    - kvm: initialize all of the kvm_debugregs structure before sending it to
+      userspace
+    - alarmtimer: Prevent starvation by small intervals and SIG_IGN
+    - ASoC: SOF: Intel: hda-dai: fix possible stream_tag leak
+    - net: sched: sch: Fix off by one in htb_activate_prios()
+    - platform/x86/amd: pmc: add CONFIG_SERIO dependency
+    - Linux 5.15.95
+  * CVE-2023-1075
+    - net/tls: tls_is_tx_ready() checked list_entry
+  * devlink_port_split from ubuntu_kernel_selftests.net fails on hirsute
+    (KeyError: 'flavour') (LP: #1937133)
+    - selftests: net: devlink_port_split.py: skip test if no suitable device
+      available
+  * Connection timeout due to conntrack limits (LP: #2011616)
+    - netfilter: conntrack: adopt safer max chain length
+  * Jammy update: v5.15.94 upstream stable release (LP: #2012673)
+    - mm/migration: return errno when isolate_huge_page failed
+    - migrate: hugetlb: check for hugetlb shared PMD in node migration
+    - btrfs: limit device extents to the device size
+    - btrfs: zlib: zero-initialize zlib workspace
+    - ALSA: hda/realtek: Add Positivo N14KP6-TG
+    - ALSA: emux: Avoid potential array out-of-bound in snd_emux_xg_control()
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro 360
+    - ALSA: hda/realtek: Enable mute/micmute LEDs on HP Elitebook, 645 G9
+    - tracing: Fix poll() and select() do not work on per_cpu trace_pipe and
+      trace_pipe_raw
+    - of/address: Return an error when no valid dma-ranges are found
+    - can: j1939: do not wait 250 ms if the same addr was already claimed
+    - xfrm: compat: change expression for switch in xfrm_xlate64
+    - IB/hfi1: Restore allocated resources on failed copyout
+    - xfrm/compat: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
+    - IB/IPoIB: Fix legacy IPoIB due to wrong number of queues
+    - RDMA/irdma: Fix potential NULL-ptr-dereference
+    - RDMA/usnic: use iommu_map_atomic() under spin_lock()
+    - xfrm: fix bug with DSCP copy to v6 from v4 tunnel
+    - net: phylink: move phy_device_free() to correctly release phy device
+    - bonding: fix error checking in bond_debug_reregister()
+    - net: phy: meson-gxl: use MMD access dummy stubs for GXL, internal PHY
+    - ionic: clean interrupt before enabling queue to avoid credit race
+    - uapi: add missing ip/ipv6 header dependencies for linux/stddef.h
+    - ice: Do not use WQ_MEM_RECLAIM flag for workqueue
+    - net: dsa: mt7530: don't change PVC_EG_TAG when CPU port becomes VLAN-aware
+    - net: mscc: ocelot: fix VCAP filters not matching on MAC with "protocol
+      802.1Q"
+    - net/mlx5e: Move repeating clear_bit in mlx5e_rx_reporter_err_rq_cqe_recover
+    - net/mlx5e: Introduce the mlx5e_flush_rq function
+    - net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
+    - net/mlx5: Bridge, fix ageing of peer FDB entries
+    - net/mlx5e: IPoIB, Show unknown speed instead of error
+    - net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
+    - net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
+    - net/mlx5: Serialize module cleanup with reload and remove
+    - igc: Add ndo_tx_timeout support
+    - rds: rds_rm_zerocopy_callback() use list_first_entry()
+    - selftests: forwarding: lib: quote the sysctl values
+    - ALSA: pci: lx6464es: fix a debug loop
+    - riscv: stacktrace: Fix missing the first frame
+    - ASoC: topology: Return -ENOMEM on memory allocation failure
+    - pinctrl: mediatek: Fix the drive register definition of some Pins
+    - pinctrl: aspeed: Fix confusing types in return value
+    - pinctrl: single: fix potential NULL dereference
+    - spi: dw: Fix wrong FIFO level setting for long xfers
+    - pinctrl: intel: Restore the pins that used to be in Direct IRQ mode
+    - cifs: Fix use-after-free in rdata->read_into_pages()
+    - net: USB: Fix wrong-direction WARNING in plusb.c
+    - mptcp: be careful on subflow status propagation on errors
+    - btrfs: free device in btrfs_close_devices for a single device filesystem
+    - usb: core: add quirk for Alcor Link AK9563 smartcard reader
+    - usb: typec: altmodes/displayport: Fix probe pin assign check
+    - clk: ingenic: jz4760: Update M/N/OD calculation algorithm
+    - ceph: flush cap releases when the session is flushed
+    - riscv: Fixup race condition on PG_dcache_clean in flush_icache_pte
+    - powerpc/64s/interrupt: Fix interrupt exit race with security mitigation
+      switch
+    - rtmutex: Ensure that the top waiter is always woken up
+    - arm64: dts: meson-gx: Make mmc host controller interrupts level-sensitive
+    - arm64: dts: meson-g12-common: Make mmc host controller interrupts level-
+      sensitive
+    - arm64: dts: meson-axg: Make mmc host controller interrupts level-sensitive
+    - Fix page corruption caused by racy check in __free_pages
+    - drm/amdgpu/fence: Fix oops due to non-matching drm_sched init/fini
+    - drm/i915: Initialize the obj flags for shmem objects
+    - drm/i915: Fix VBT DSI DVO port handling
+    - x86/speculation: Identify processors vulnerable to SMT RSB predictions
+    - KVM: x86: Mitigate the cross-thread return address predictions bug
+    - Documentation/hw-vuln: Add documentation for Cross-Thread Return Predictions
+    - Linux 5.15.94
+  * Jammy update: v5.15.93 upstream stable release (LP: #2012665)
+    - firewire: fix memory leak for payload of request subaction to IEC 61883-1
+      FCP region
+    - bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()
+    - ASoC: Intel: boards: fix spelling in comments
+    - ASoC: Intel: bytcht_es8316: move comment to the right place
+    - ASoC: Intel: bytcht_es8316: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_rt5651: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_rt5640: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_wm5102: Drop reference count of ACPI device after use
+    - bpf: Fix a possible task gone issue with bpf_send_signal[_thread]() helpers
+    - ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
+    - bpf: Support <8-byte scalar spill and refill
+    - bpf: Fix to preserve reg parent/live fields when copying range info
+    - bpf, sockmap: Check for any of tcp_bpf_prots when cloning a listener
+    - arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
+    - drm/vc4: hdmi: make CEC adapter name unique
+    - scsi: Revert "scsi: core: map PQ=1, PDT=other values to
+      SCSI_SCAN_TARGET_PRESENT"
+    - vhost/net: Clear the pending messages when the backend is removed
+    - WRITE is "data source", not destination...
+    - READ is "data destination", not source...
+    - fix iov_iter_bvec() "direction" argument
+    - fix "direction" argument of iov_iter_kvec()
+    - ice: Prevent set_channel from changing queues while RDMA active
+    - qede: execute xdp_do_flush() before napi_complete_done()
+    - virtio-net: execute xdp_do_flush() before napi_complete_done()
+    - dpaa_eth: execute xdp_do_flush() before napi_complete_done()
+    - dpaa2-eth: execute xdp_do_flush() before napi_complete_done()
+    - sfc: correctly advertise tunneled IPv6 segmentation
+    - net: phy: dp83822: Fix null pointer access on DP83825/DP83826 devices
+    - block/bfq-iosched.c: use "false" rather than "BLK_RW_ASYNC"
+    - block, bfq: replace 0/1 with false/true in bic apis
+    - block, bfq: fix uaf for bfqq in bic_set_bfqq()
+    - netrom: Fix use-after-free caused by accept on already connected socket
+    - drm/i915/guc: Fix locking when searching for a hung request
+    - drm/i915/adlp: Fix typo for reference clock
+    - netfilter: br_netfilter: disable sabotage_in hook after first suppression
+    - squashfs: harden sanity check in squashfs_read_xattr_id_table
+    - net: phy: meson-gxl: Add generic dummy stubs for MMD register access
+    - ip/ip6_gre: Fix changing addr gen mode not generating IPv6 link local
+      address
+    - ip/ip6_gre: Fix non-point-to-point tunnel not generating IPv6 link local
+      address
+    - riscv: kprobe: Fixup kernel panic when probing an illegal position
+    - igc: return an error if the mac type is unknown in
+      igc_ptp_systim_to_hwtstamp()
+    - can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
+    - ata: libata: Fix sata_down_spd_limit() when no link speed is reported
+    - selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
+    - selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
+    - selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy
+      benchmarking
+    - virtio-net: Keep stop() to follow mirror sequence of open()
+    - net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
+    - efi: fix potential NULL deref in efi_mem_reserve_persistent
+    - i2c: designware-pci: Add new PCI IDs for AMD NAVI GPU
+    - i2c: mxs: suppress probe-deferral error message
+    - scsi: target: core: Fix warning on RT kernels
+    - perf/x86/intel: Add Emerald Rapids
+    - scsi: iscsi_tcp: Fix UAF during logout when accessing the shost ipaddress
+    - scsi: iscsi_tcp: Fix UAF during login when accessing the shost ipaddress
+    - i2c: rk3x: fix a bunch of kernel-doc warnings
+    - platform/x86: gigabyte-wmi: add support for B450M DS3H WIFI-CF
+    - net/x25: Fix to not accept on connected socket
+    - drm/amd/display: Fix timing not changning when freesync video is enabled
+    - iio: adc: stm32-dfsdm: fill module aliases
+    - usb: dwc3: qcom: enable vbus override when in OTG dr-mode
+    - usb: gadget: f_fs: Fix unbalanced spinlock in __ffs_ep0_queue_wait
+    - vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF
+    - Input: i8042 - add Clevo PCX0DX to i8042 quirk table
+    - fbcon: Check font dimension limits
+    - net: qrtr: free memory on error path in radix_tree_insert()
+    - watchdog: diag288_wdt: do not use stack buffers for hardware data
+    - watchdog: diag288_wdt: fix __diag288() inline assembly
+    - ALSA: hda/realtek: Add Acer Predator PH315-54
+    - efi: Accept version 2 of memory attributes table
+    - iio: hid: fix the retval in accel_3d_capture_sample
+    - iio: hid: fix the retval in gyro_3d_capture_sample
+    - iio: adc: berlin2-adc: Add missing of_node_put() in error path
+    - iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
+    - iio: imu: fxos8700: fix ACCEL measurement range selection
+    - iio: imu: fxos8700: fix incomplete ACCEL and MAGN channels readback
+    - iio: imu: fxos8700: fix IMU data bits returned to user space
+    - iio: imu: fxos8700: fix map label of channel type to MAGN sensor
+    - iio: imu: fxos8700: fix swapped ACCEL and MAGN channels readback
+    - iio: imu: fxos8700: fix incorrect ODR mode readback
+    - iio: imu: fxos8700: fix failed initialization ODR mode assignment
+    - iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
+    - iio: imu: fxos8700: fix MAGN sensor scale and unit
+    - nvmem: qcom-spmi-sdam: fix module autoloading
+    - parisc: Fix return code of pdc_iodc_print()
+    - parisc: Wire up PTRACE_GETREGS/PTRACE_SETREGS for compat case
+    - riscv: disable generation of unwind tables
+    - mm: hugetlb: proc: check for hugetlb shared PMD in /proc/PID/smaps
+    - usb: gadget: f_uac2: Fix incorrect increment of bNumEndpoints
+    - kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
+    - x86/debug: Fix stack recursion caused by wrongly ordered DR7 accesses
+    - fpga: stratix10-soc: Fix return value check in s10_ops_write_init()
+    - mm/swapfile: add cond_resched() in get_swap_pages()
+    - highmem: round down the address passed to kunmap_flush_on_unmap()
+    - Squashfs: fix handling and sanity checking of xattr_ids count
+    - drm/i915: Fix potential bit_17 double-free
+    - nvmem: core: initialise nvmem->id early
+    - nvmem: core: remove nvmem_config wp_gpio
+    - nvmem: core: fix cell removal on error
+    - serial: 8250_dma: Fix DMA Rx completion race
+    - serial: 8250_dma: Fix DMA Rx rearm race
+    - phy: qcom-qmp-combo: disable runtime PM on unbind
+    - phy: qcom-qmp-combo: fix memleak on probe deferral
+    - phy: qcom-qmp-usb: fix memleak on probe deferral
+    - phy: qcom-qmp-combo: fix broken power on
+    - phy: qcom-qmp-combo: fix runtime suspend
+    - bpf: Fix incorrect state pruning for <8B spill/fill
+    - bpf: Do not reject when the stack read size is different from the tracked
+      scalar size
+    - iio:adc:twl6030: Enable measurement of VAC
+    - powerpc/imc-pmu: Revert nest_init_lock to being a mutex
+    - fs/ntfs3: Validate attribute data and valid sizes
+    - ovl: Use "buf" flexible array for memcpy() destination
+    - fbdev: smscufx: fix error handling code in ufx_usb_probe
+    - f2fs: fix to do sanity check on i_extra_isize in is_alive()
+    - wifi: brcmfmac: Check the count value of channel spec to prevent out-of-
+      bounds reads
+    - gfs2: Cosmetic gfs2_dinode_{in,out} cleanup
+    - gfs2: Always check inode size of inline inodes
+    - bpf: Skip invalid kfunc call in backtrack_insn
+    - Linux 5.15.93
+  * CVE-2023-1118
+    - media: rc: Fix use-after-free bugs caused by ene_tx_irqsim()
+  * [SRU][Ubuntu 22.04.1]: Observed "Array Index out of bounds" Call Trace
+    multiple times on Ubuntu 22.04.1 OS during boot (LP: #2008157)
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_FW_RAID_MAP
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_FW_RAID_MAP_DYNAMIC
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_DRV_RAID_MAP
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_PD_CFG_SEQ_NUM_SYNC
+    - scsi: megaraid_sas: Use struct_size() in code related to struct
+      MR_FW_RAID_MAP
+    - scsi: megaraid_sas: Use struct_size() in code related to struct
+      MR_PD_CFG_SEQ_NUM_SYNC
+  * Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo
+    child qdiscs" (LP: #2011926)
+    - Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo
+      child qdiscs"
+
+  [ Ubuntu: 5.15.0-71.78 ]
+
+  * jammy/linux: 5.15.0-71.78 -proposed tracker (LP: #2016820)
+  * CVE-2023-1872
+    - io_uring: add missing lock in io_get_file_fixed
+    - io_uring: ensure that io_init_req() passes in the right issue_flags
+  * CVE-2023-1829
+    - net/sched: Retire tcindex classifier
+    - [Config]: Make sure CONFIG_NET_CLS_TCINDEX is not available
+
+ -- Masahiro Yamada <masahiro.yamada@canonical.com>  Fri, 19 May 2023 17:01:57 +0900
+
+linux-xilinx-zynqmp (5.15.0-1021.25) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1021.25 -proposed tracker (LP: #2008753)
+
+  * Jammy update: v5.15.81 upstream stable release (LP: #2003130)
+    - [Config] updateconfigs for CC_HAS_ASM_GOTO_TIED_OUTPUT
+    - [Config] updateconfigs for INET_TABLE_PERTURB_ORDER
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] remove unneeded packqages
+
+  [ Ubuntu: 5.15.0-70.77 ]
+
+  * jammy/linux: 5.15.0-70.77 -proposed tracker (LP: #2011918)
+  * CVE-2023-26545
+    - net: mpls: fix stale pointer if allocation fails during device rename
+  * CVE-2023-1281
+    - net/sched: tcindex: update imperfect hash filters respecting rcu
+  * [SRU][Ubuntu 22.04.1] mpi3mr: Add management application interface(BSG)
+    support (LP: #1971151)
+    - scsi: mpi3mr: Add bsg device support
+    - scsi: mpi3mr: Add support for driver commands
+    - scsi: mpi3mr: Move data structures/definitions from MPI headers to uapi
+      header
+    - scsi: mpi3mr: Add support for MPT commands
+    - scsi: mpi3mr: Add support for PEL commands
+    - scsi: mpi3mr: Expose adapter state to sysfs
+    - scsi: mpi3mr: Add support for NVMe passthrough
+    - scsi: mpi3mr: Update driver version to 8.0.0.69.0
+    - scsi: mpi3mr: Increase I/O timeout value to 60s
+    - scsi: mpi3mr: Hidden drives not removed during soft reset
+    - scsi: mpi3mr: Return I/Os to an unrecoverable HBA with DID_ERROR
+    - scsi: mpi3mr: Fix a NULL vs IS_ERR() bug in mpi3mr_bsg_init()
+    - scsi: mpi3mr: Return error if dma_alloc_coherent() fails
+    - scsi: mpi3mr: Add shost related sysfs attributes
+    - scsi: mpi3mr: Add target device related sysfs attributes
+    - scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
+    - scsi: mpi3mr: Fix kernel-doc
+  * cpufreq: intel_pstate: Update Balance performance EPP for Sapphire Rapids
+    (LP: #2008519)
+    - cpufreq: intel_pstate: Update EPP for AlderLake mobile
+    - cpufreq: intel_pstate: Adjust balance_performance EPP for Sapphire Rapids
+  * Fail to output sound to external monitor which connects via docking station
+    (LP: #2009024)
+    - [Config] Enable CONFIG_SND_HDA_INTEL_HDMI_SILENT_STREAM
+  * Fix mediatek wifi driver crash when loading wrong SAR table (LP: #2009118)
+    - wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
+  * Jammy update: v5.15.92 upstream stable release (LP: #2011472)
+    - ARM: dts: imx: Fix pca9547 i2c-mux node name
+    - ARM: dts: vf610: Fix pca9548 i2c-mux node names
+    - arm64: dts: freescale: Fix pca954x i2c-mux node names
+    - arm64: dts: imx8mq-thor96: fix no-mmc property for SDHCI
+    - firmware: arm_scmi: Clear stale xfer->hdr.status
+    - bpf: Skip task with pid=1 in send_signal_common()
+    - erofs/zmap.c: Fix incorrect offset calculation
+    - blk-cgroup: fix missing pd_online_fn() while activating policy
+    - HID: playstation: sanity check DualSense calibration data.
+    - dmaengine: imx-sdma: Fix a possible memory leak in sdma_transfer_init
+    - cifs: fix return of uninitialized rc in dfs_cache_update_tgthint()
+    - extcon: usbc-tusb320: fix kernel-doc warning
+    - Bluetooth: fix null ptr deref on hci_sync_conn_complete_evt
+    - tools: fix ARRAY_SIZE defines in tools and selftests hdrs
+    - selftests/vm: remove ARRAY_SIZE define from individual tests
+    - selftests: Provide local define of __cpuid_count()
+    - net: fix NULL pointer in skb_segment_list
+    - net: mctp: purge receive queues on sk destruction
+    - Linux 5.15.92
+  * Jammy update: v5.15.91 upstream stable release (LP: #2011467)
+    - memory: tegra: Remove clients SID override programming
+    - memory: atmel-sdramc: Fix missing clk_disable_unprepare in
+      atmel_ramc_probe()
+    - memory: mvebu-devbus: Fix missing clk_disable_unprepare in
+      mvebu_devbus_probe()
+    - dmaengine: ti: k3-udma: Do conditional decrement of
+      UDMA_CHAN_RT_PEER_BCNT_REG
+    - arm64: dts: imx8mp-phycore-som: Remove invalid PMIC property
+    - ARM: dts: imx6ul-pico-dwarf: Use 'clock-frequency'
+    - ARM: dts: imx7d-pico: Use 'clock-frequency'
+    - ARM: dts: imx6qdl-gw560x: Remove incorrect 'uart-has-rtscts'
+    - arm64: dts: imx8mm-beacon: Fix ecspi2 pinmux
+    - ARM: imx: add missing of_node_put()
+    - HID: intel_ish-hid: Add check for ishtp_dma_tx_map
+    - arm64: dts: imx8mm-venice-gw7901: fix USB2 controller OC polarity
+    - soc: imx8m: Fix incorrect check for of_clk_get_by_name()
+    - reset: uniphier-glue: Use reset_control_bulk API
+    - reset: uniphier-glue: Fix possible null-ptr-deref
+    - EDAC/highbank: Fix memory leak in highbank_mc_probe()
+    - firmware: arm_scmi: Harden shared memory access in fetch_response
+    - firmware: arm_scmi: Harden shared memory access in fetch_notification
+    - tomoyo: fix broken dependency on *.conf.default
+    - RDMA/core: Fix ib block iterator counter overflow
+    - IB/hfi1: Reject a zero-length user expected buffer
+    - IB/hfi1: Reserve user expected TIDs
+    - IB/hfi1: Fix expected receive setup error exit issues
+    - IB/hfi1: Immediately remove invalid memory from hardware
+    - IB/hfi1: Remove user expected buffer invalidate race
+    - affs: initialize fsdata in affs_truncate()
+    - PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
+    - arm64: dts: qcom: msm8992: Don't use sfpb mutex
+    - arm64: dts: qcom: msm8992-libra: Add CPU regulators
+    - arm64: dts: qcom: msm8992-libra: Fix the memory map
+    - phy: ti: fix Kconfig warning and operator precedence
+    - NFSD: fix use-after-free in nfsd4_ssc_setup_dul()
+    - ARM: dts: at91: sam9x60: fix the ddr clock for sam9x60
+    - amd-xgbe: TX Flow Ctrl Registers are h/w ver dependent
+    - amd-xgbe: Delay AN timeout during KR training
+    - bpf: Fix pointer-leak due to insufficient speculative store bypass
+      mitigation
+    - phy: rockchip-inno-usb2: Fix missing clk_disable_unprepare() in
+      rockchip_usb2phy_power_on()
+    - net: nfc: Fix use-after-free in local_cleanup()
+    - net: wan: Add checks for NULL for utdm in undo_uhdlc_init and unmap_si_regs
+    - net: enetc: avoid deadlock in enetc_tx_onestep_tstamp()
+    - sch_htb: Avoid grafting on htb_destroy_class_offload when destroying htb
+    - gpio: use raw spinlock for gpio chip shadowed data
+    - gpio: mxc: Protect GPIO irqchip RMW with bgpio spinlock
+    - gpio: mxc: Always set GPIOs used as interrupt source to INPUT mode
+    - pinctrl/rockchip: Use temporary variable for struct device
+    - pinctrl/rockchip: add error handling for pull/drive register getters
+    - pinctrl: rockchip: fix reading pull type on rk3568
+    - net: stmmac: Fix queue statistics reading
+    - net/sched: sch_taprio: fix possible use-after-free
+    - l2tp: Serialize access to sk_user_data with sk_callback_lock
+    - l2tp: Don't sleep and disable BH under writer-side sk_callback_lock
+    - l2tp: convert l2tp_tunnel_list to idr
+    - l2tp: close all race conditions in l2tp_tunnel_register()
+    - octeontx2-pf: Avoid use of GFP_KERNEL in atomic context
+    - net: usb: sr9700: Handle negative len
+    - net: mdio: validate parameter addr in mdiobus_get_phy()
+    - HID: check empty report_list in hid_validate_values()
+    - HID: check empty report_list in bigben_probe()
+    - net: stmmac: fix invalid call to mdiobus_get_phy()
+    - pinctrl: rockchip: fix mux route data for rk3568
+    - HID: revert CHERRY_MOUSE_000C quirk
+    - usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait
+    - usb: gadget: f_fs: Ensure ep0req is dequeued before free_request
+    - Bluetooth: Fix possible deadlock in rfcomm_sk_state_change
+    - net: ipa: disable ipa interrupt during suspend
+    - net/mlx5: E-switch, Fix setting of reserved fields on
+      MODIFY_SCHEDULING_ELEMENT
+    - net: mlx5: eliminate anonymous module_init & module_exit
+    - drm/panfrost: fix GENERIC_ATOMIC64 dependency
+    - dmaengine: Fix double increment of client_count in dma_chan_get()
+    - net: macb: fix PTP TX timestamp failure due to packet padding
+    - virtio-net: correctly enable callback during start_xmit
+    - l2tp: prevent lockdep issue in l2tp_tunnel_register()
+    - HID: betop: check shape of output reports
+    - cifs: fix potential deadlock in cache_refresh_path()
+    - dmaengine: xilinx_dma: call of_node_put() when breaking out of
+      for_each_child_of_node()
+    - phy: phy-can-transceiver: Skip warning if no "max-bitrate"
+    - drm/amd/display: fix issues with driver unload
+    - nvme-pci: fix timeout request state check
+    - tcp: avoid the lookup process failing to get sk in ehash table
+    - octeontx2-pf: Fix the use of GFP_KERNEL in atomic context on rt
+    - ptdma: pt_core_execute_cmd() should use spinlock
+    - device property: fix of node refcount leak in
+      fwnode_graph_get_next_endpoint()
+    - w1: fix deadloop in __w1_remove_master_device()
+    - w1: fix WARNING after calling w1_process()
+    - driver core: Fix test_async_probe_init saves device in wrong array
+    - selftests/net: toeplitz: fix race on tpacket_v3 block close
+    - net: dsa: microchip: ksz9477: port map correction in ALU table entry
+      register
+    - thermal/core: Remove duplicate information when an error occurs
+    - thermal/core: Rename 'trips' to 'num_trips'
+    - thermal: Validate new state in cur_state_store()
+    - thermal/core: fix error code in __thermal_cooling_device_register()
+    - thermal: core: call put_device() only after device_register() fails
+    - net: stmmac: enable all safety features by default
+    - tcp: fix rate_app_limited to default to 1
+    - scsi: iscsi: Fix multiple iSCSI session unbind events sent to userspace
+    - cpufreq: Add Tegra234 to cpufreq-dt-platdev blocklist
+    - kcsan: test: don't put the expect array on the stack
+    - cpufreq: Add SM6375 to cpufreq-dt-platdev blocklist
+    - ASoC: fsl_micfil: Correct the number of steps on SX controls
+    - net: usb: cdc_ether: add support for Thales Cinterion PLS62-W modem
+    - drm: Add orientation quirk for Lenovo ideapad D330-10IGL
+    - s390/debug: add _ASM_S390_ prefix to header guard
+    - s390: expicitly align _edata and _end symbols on page boundary
+    - perf/x86/msr: Add Emerald Rapids
+    - perf/x86/intel/uncore: Add Emerald Rapids
+    - cpufreq: armada-37xx: stop using 0 as NULL pointer
+    - ASoC: fsl_ssi: Rename AC'97 streams to avoid collisions with AC'97 CODEC
+    - ASoC: fsl-asoc-card: Fix naming of AC'97 CODEC widgets
+    - spi: spidev: remove debug messages that access spidev->spi without locking
+    - KVM: s390: interrupt: use READ_ONCE() before cmpxchg()
+    - scsi: hisi_sas: Set a port invalid only if there are no devices attached
+      when refreshing port id
+    - r8152: add vendor/device ID pair for Microsoft Devkit
+    - platform/x86: touchscreen_dmi: Add info for the CSL Panther Tab HD
+    - platform/x86: asus-nb-wmi: Add alternate mapping for KEY_SCREENLOCK
+    - lockref: stop doing cpu_relax in the cmpxchg loop
+    - firmware: coreboot: Check size of table entry and use flex-array
+    - drm/i915: Allow switching away via vga-switcheroo if uninitialized
+    - drm/i915: Remove unused variable
+    - x86: ACPI: cstate: Optimize C3 entry on AMD CPUs
+    - fs: reiserfs: remove useless new_opts in reiserfs_remount
+    - sysctl: add a new register_sysctl_init() interface
+    - kernel/panic: move panic sysctls to its own file
+    - panic: unset panic_on_warn inside panic()
+    - ubsan: no need to unset panic_on_warn in ubsan_epilogue()
+    - kasan: no need to unset panic_on_warn in end_report()
+    - exit: Add and use make_task_dead.
+    - objtool: Add a missing comma to avoid string concatenation
+    - hexagon: Fix function name in die()
+    - h8300: Fix build errors from do_exit() to make_task_dead() transition
+    - csky: Fix function name in csky_alignment() and die()
+    - ia64: make IA64_MCA_RECOVERY bool instead of tristate
+    - panic: Separate sysctl logic from CONFIG_SMP
+    - exit: Put an upper limit on how often we can oops
+    - exit: Expose "oops_count" to sysfs
+    - exit: Allow oops_limit to be disabled
+    - panic: Consolidate open-coded panic_on_warn checks
+    - panic: Introduce warn_limit
+    - panic: Expose "warn_count" to sysfs
+    - docs: Fix path paste-o for /sys/kernel/warn_count
+    - exit: Use READ_ONCE() for all oops/warn limit reads
+    - Bluetooth: hci_sync: cancel cmd_timer if hci_open failed
+    - drm/amdgpu: complete gfxoff allow signal during suspend without delay
+    - scsi: hpsa: Fix allocation size for scsi_host_alloc()
+    - KVM: SVM: fix tsc scaling cache logic
+    - module: Don't wait for GOING modules
+    - tracing: Make sure trace_printk() can output as soon as it can be used
+    - trace_events_hist: add check for return value of 'create_hist_field'
+    - ftrace/scripts: Update the instructions for ftrace-bisect.sh
+    - cifs: Fix oops due to uncleared server->smbd_conn in reconnect
+    - i2c: mv64xxx: Remove shutdown method from driver
+    - i2c: mv64xxx: Add atomic_xfer method to driver
+    - ksmbd: add smbd max io size parameter
+    - ksmbd: add max connections parameter
+    - ksmbd: do not sign response to session request for guest login
+    - ksmbd: downgrade ndr version error message to debug
+    - ksmbd: limit pdu length size according to connection status
+    - ovl: fail on invalid uid/gid mapping at copy up
+    - KVM: x86/vmx: Do not skip segment attributes if unusable bit is set
+    - KVM: arm64: GICv4.1: Fix race with doorbell on VPE activation/deactivation
+    - thermal: intel: int340x: Protect trip temperature from concurrent updates
+    - ipv6: fix reachability confirmation with proxy_ndp
+    - ARM: 9280/1: mm: fix warning on phys_addr_t to void pointer assignment
+    - EDAC/device: Respect any driver-supplied workqueue polling value
+    - EDAC/qcom: Do not pass llcc_driv_data as edac_device_ctl_info's pvt_info
+    - net: mana: Fix IRQ name - add PCI and queue number
+    - scsi: ufs: core: Fix devfreq deadlocks
+    - i2c: designware: use casting of u64 in clock multiplication to avoid
+      overflow
+    - netlink: prevent potential spectre v1 gadgets
+    - net: fix UaF in netns ops registration error path
+    - drm/i915/selftest: fix intel_selftest_modify_policy argument types
+    - netfilter: nft_set_rbtree: Switch to node list walk for overlap detection
+    - netfilter: nft_set_rbtree: skip elements in transaction from garbage
+      collection
+    - netlink: annotate data races around nlk->portid
+    - netlink: annotate data races around dst_portid and dst_group
+    - netlink: annotate data races around sk_state
+    - ipv4: prevent potential spectre v1 gadget in ip_metrics_convert()
+    - ipv4: prevent potential spectre v1 gadget in fib_metrics_match()
+    - netfilter: conntrack: fix vtag checks for ABORT/SHUTDOWN_COMPLETE
+    - netrom: Fix use-after-free of a listening socket.
+    - net/sched: sch_taprio: do not schedule in taprio_reset()
+    - sctp: fail if no bound addresses can be used for a given scope
+    - riscv/kprobe: Fix instruction simulation of JALR
+    - nvme: fix passthrough csi check
+    - gpio: mxc: Unlock on error path in mxc_flip_edge()
+    - ravb: Rename "no_ptp_cfg_active" and "ptp_cfg_active" variables
+    - net: ravb: Fix lack of register setting after system resumed for Gen3
+    - net: ravb: Fix possible hang if RIS2_QFF1 happen
+    - net: mctp: mark socks as dead on unhash, prevent re-add
+    - thermal: intel: int340x: Add locking to int340x_thermal_get_trip_type()
+    - net/tg3: resolve deadlock in tg3_reset_task() during EEH
+    - net: mdio-mux-meson-g12a: force internal PHY off on mux switch
+    - treewide: fix up files incorrectly marked executable
+    - tools: gpio: fix -c option of gpio-event-mon
+    - Revert "Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI
+      mode"
+    - cpufreq: Move to_gov_attr_set() to cpufreq.h
+    - cpufreq: governor: Use kobject release() method to free dbs_data
+    - kbuild: Allow kernel installation packaging to override pkg-config
+    - block: fix and cleanup bio_check_ro
+    - x86/i8259: Mark legacy PIC interrupts with IRQ_LEVEL
+    - netfilter: conntrack: unify established states for SCTP paths
+    - perf/x86/amd: fix potential integer overflow on shift of a int
+    - Linux 5.15.91
+  * Kernel livepatch support for for s390x (LP: #1639924)
+    - sched: Improve try_invoke_on_locked_down_task()
+    - sched,rcu: Rework try_invoke_on_locked_down_task()
+    - sched,livepatch: Use task_call_func()
+    - sched: Simplify wake_up_*idle*()
+    - sched,livepatch: Use wake_up_if_idle()
+    - sched: Improve wake_up_all_idle_cpus() take #2
+    - s390/entry: remove unused expoline thunk
+    - s390: remove unused expoline to BC instructions
+    - s390/nospec: generate single register thunks if possible
+    - s390/nospec: add an option to use thunk-extern
+    - s390/nospec: align and size extern thunks
+    - bug: Use normal relative pointers in 'struct bug_entry'
+    - s390/nospec: build expoline.o for modules_prepare target
+    - [Config] Enable EXPOLINE_EXTERN on s390x
+    - [Config] s390x: Removing UBSAN from configuration
+  * Do not sort the task scan result from /proc when synthesizing perf events
+    (LP: #2008971)
+    - perf synthetic-events: Don't sort the task scan result from /proc
+  * linux: Staging modules should be unsigned (LP: #1642368)
+    - [Packaging] Move and update signature inclusion list
+    - SAUCE: Add selective signing of staging modules
+    - [Packaging] Add module-signature-check
+    - [Packaging] module-signature-check: Check debian.<foo>/signature-inclusion
+    - [Packaging] Introduce debian/scripts/sign-module
+    - SAUCE: Switch to using debian/scripts/sign-module
+  * Jammy update: v5.15.90 upstream stable release (LP: #2008933)
+    - btrfs: fix trace event name typo for FLUSH_DELAYED_REFS
+    - pNFS/filelayout: Fix coalescing test for single DS
+    - tools/virtio: initialize spinlocks in vring_test.c
+    - virtio_pci: modify ENOENT to EINVAL
+    - vduse: Validate vq_num in vduse_validate_config()
+    - net/ethtool/ioctl: return -EOPNOTSUPP if we have no phy stats
+    - r8169: move rtl_wol_enable_rx() and rtl_prepare_power_down()
+    - RDMA/srp: Move large values to a new enum for gcc13
+    - btrfs: always report error in run_one_delayed_ref()
+    - x86/asm: Fix an assembler warning with current binutils
+    - f2fs: let's avoid panic if extent_tree is not created
+    - perf/x86/rapl: Treat Tigerlake like Icelake
+    - fbdev: omapfb: avoid stack overflow warning
+    - Bluetooth: hci_qca: Fix driver shutdown on closed serdev
+    - wifi: brcmfmac: fix regression for Broadcom PCIe wifi devices
+    - wifi: mac80211: sdata can be NULL during AMPDU start
+    - Add exception protection processing for vd in axi_chan_handle_err function
+    - zonefs: Detect append writes at invalid locations
+    - nilfs2: fix general protection fault in nilfs_btree_insert()
+    - efi: fix userspace infinite retry read efivars after EFI runtime services
+      page fault
+    - ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
+    - ALSA: hda/realtek: fix mute/micmute LEDs don't work for a HP platform
+    - drm/amdgpu: disable runtime pm on several sienna cichlid cards(v2)
+    - drm/amd: Delay removal of the firmware framebuffer
+    - hugetlb: unshare some PMDs when splitting VMAs
+    - io_uring: don't gate task_work run on TIF_NOTIFY_SIGNAL
+    - eventpoll: add EPOLL_URING_WAKE poll wakeup flag
+    - eventfd: provide a eventfd_signal_mask() helper
+    - io_uring: pass in EPOLL_URING_WAKE for eventfd signaling and wakeups
+    - io_uring: improve send/recv error handling
+    - io_uring: ensure recv and recvmsg handle MSG_WAITALL correctly
+    - io_uring: add flag for disabling provided buffer recycling
+    - io_uring: support MSG_WAITALL for IORING_OP_SEND(MSG)
+    - io_uring: allow re-poll if we made progress
+    - io_uring: fix async accept on O_NONBLOCK sockets
+    - io_uring: ensure that cached task references are always put on exit
+    - io_uring: remove duplicated calls to io_kiocb_ppos
+    - io_uring: update kiocb->ki_pos at execution time
+    - io_uring: do not recalculate ppos unnecessarily
+    - io_uring/rw: defer fsnotify calls to task context
+    - xhci-pci: set the dma max_seg_size
+    - usb: xhci: Check endpoint is valid before dereferencing it
+    - xhci: Fix null pointer dereference when host dies
+    - xhci: Add update_hub_device override for PCI xHCI hosts
+    - xhci: Add a flag to disable USB3 lpm on a xhci root port level.
+    - usb: acpi: add helper to check port lpm capability using acpi _DSM
+    - xhci: Detect lpm incapable xHC USB3 roothub ports from ACPI tables
+    - prlimit: do_prlimit needs to have a speculation check
+    - USB: serial: option: add Quectel EM05-G (GR) modem
+    - USB: serial: option: add Quectel EM05-G (CS) modem
+    - USB: serial: option: add Quectel EM05-G (RS) modem
+    - USB: serial: option: add Quectel EC200U modem
+    - USB: serial: option: add Quectel EM05CN (SG) modem
+    - USB: serial: option: add Quectel EM05CN modem
+    - staging: vchiq_arm: fix enum vchiq_status return types
+    - USB: misc: iowarrior: fix up header size for USB_DEVICE_ID_CODEMERCS_IOW100
+    - misc: fastrpc: Don't remove map on creater_process and device_release
+    - misc: fastrpc: Fix use-after-free race condition for maps
+    - usb: core: hub: disable autosuspend for TI TUSB8041
+    - comedi: adv_pci1760: Fix PWM instruction handling
+    - ACPI: PRM: Check whether EFI runtime is available
+    - mmc: sunxi-mmc: Fix clock refcount imbalance during unbind
+    - mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting
+    - btrfs: do not abort transaction on failure to write log tree when syncing
+      log
+    - btrfs: fix race between quota rescan and disable leading to NULL pointer
+      deref
+    - cifs: do not include page data when checking signature
+    - thunderbolt: Use correct function to calculate maximum USB3 link rate
+    - riscv: dts: sifive: fu740: fix size of pcie 32bit memory
+    - bpf: restore the ebpf program ID for BPF_AUDIT_UNLOAD and
+      PERF_BPF_EVENT_PROG_UNLOAD
+    - staging: mt7621-dts: change some node hex addresses to lower case
+    - tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
+    - tty: fix possible null-ptr-defer in spk_ttyio_release
+    - USB: serial: cp210x: add SCALANCE LPE-9000 device id
+    - usb: cdns3: remove fetched trb from cache before dequeuing
+    - usb: host: ehci-fsl: Fix module alias
+    - usb: typec: tcpm: Fix altmode re-registration causes sysfs create fail
+    - usb: typec: altmodes/displayport: Add pin assignment helper
+    - usb: typec: altmodes/displayport: Fix pin assignment calculation
+    - usb: gadget: g_webcam: Send color matching descriptor per frame
+    - usb: gadget: f_ncm: fix potential NULL ptr deref in ncm_bitrate()
+    - usb-storage: apply IGNORE_UAS only for HIKSEMI MD202 on RTL9210
+    - dt-bindings: phy: g12a-usb2-phy: fix compatible string documentation
+    - dt-bindings: phy: g12a-usb3-pcie-phy: fix compatible string documentation
+    - serial: pch_uart: Pass correct sg to dma_unmap_sg()
+    - dmaengine: lgm: Move DT parsing after initialization
+    - dmaengine: tegra210-adma: fix global intr clear
+    - dmaengine: idxd: Let probe fail when workqueue cannot be enabled
+    - serial: amba-pl011: fix high priority character transmission in rs486 mode
+    - serial: atmel: fix incorrect baudrate setup
+    - gsmi: fix null-deref in gsmi_get_variable
+    - mei: me: add meteor lake point M DID
+    - drm/i915: re-disable RC6p on Sandy Bridge
+    - drm/i915/display: Check source height is > 0
+    - drm/amd/display: Fix set scaling doesn's work
+    - drm/amd/display: Calculate output_color_space after pixel encoding
+      adjustment
+    - drm/amd/display: Fix COLOR_SPACE_YCBCR2020_TYPE matrix
+    - drm/amdgpu: drop experimental flag on aldebaran
+    - fs/ntfs3: Fix attr_punch_hole() null pointer derenference
+    - arm64: efi: Execute runtime services from a dedicated stack
+    - efi: rt-wrapper: Add missing include
+    - x86/fpu: Use _Alignof to avoid undefined behavior in TYPE_ALIGN
+    - tracing: Use alignof__(struct {type b;}) instead of offsetof()
+    - io_uring: io_kiocb_update_pos() should not touch file for non -1 offset
+    - io_uring/net: fix fast_iov assignment in io_setup_async_msg()
+    - net/mlx5: fix missing mutex_unlock in mlx5_fw_fatal_reporter_err_work()
+    - block: mq-deadline: Rename deadline_is_seq_writes()
+    - soc: qcom: apr: Make qcom,protection-domain optional again
+    - mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
+    - io_uring: Clean up a false-positive warning from GCC 9.3.0
+    - io_uring: fix double poll leak on repolling
+    - io_uring/rw: ensure kiocb_end_write() is always called
+    - io_uring/rw: remove leftover debug statement
+    - Linux 5.15.90
+  * Jammy update: v5.15.89 upstream stable release (LP: #2008929)
+    - ALSA: control-led: use strscpy in set_led_id()
+    - ALSA: hda/realtek - Turn on power early
+    - ALSA: hda/realtek: Enable mute/micmute LEDs on HP Spectre x360 13-aw0xxx
+    - KVM: arm64: Fix S1PTW handling on RO memslots
+    - KVM: arm64: nvhe: Fix build with profile optimization
+    - selftests: kvm: Fix a compile error in selftests/kvm/rseq_test.c
+    - efi: tpm: Avoid READ_ONCE() for accessing the event log
+    - docs: Fix the docs build with Sphinx 6.0
+    - net: stmmac: add aux timestamps fifo clearance wait
+    - perf auxtrace: Fix address filter duplicate symbol selection
+    - s390/kexec: fix ipl report address for kdump
+    - ASoC: qcom: lpass-cpu: Fix fallback SD line index handling
+    - s390/cpum_sf: add READ_ONCE() semantics to compare and swap loops
+    - s390/percpu: add READ_ONCE() to arch_this_cpu_to_op_simple()
+    - drm/virtio: Fix GEM handle creation UAF
+    - drm/i915/gt: Reset twice
+    - net/mlx5e: Set action fwd flag when parsing tc action goto
+    - cifs: Fix uninitialized memory read for smb311 posix symlink create
+    - platform/x86: dell-privacy: Only register SW_CAMERA_LENS_COVER if present
+    - platform/surface: aggregator: Ignore command messages not intended for us
+    - platform/x86: dell-privacy: Fix SW_CAMERA_LENS_COVER reporting
+    - dt-bindings: msm: dsi-controller-main: Fix operating-points-v2 constraint
+    - drm/msm/adreno: Make adreno quirks not overwrite each other
+    - dt-bindings: msm: dsi-controller-main: Fix power-domain constraint
+    - dt-bindings: msm: dsi-controller-main: Fix description of core clock
+    - dt-bindings: msm: dsi-phy-28nm: Add missing qcom, dsi-phy-regulator-ldo-mode
+    - platform/x86: ideapad-laptop: Add Legion 5 15ARH05 DMI id to
+      set_fn_lock_led_list[]
+    - drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux
+      transfer
+    - dt-bindings: msm/dsi: Don't require vdds-supply on 10nm PHY
+    - dt-bindings: msm/dsi: Don't require vcca-supply on 14nm PHY
+    - platform/x86: sony-laptop: Don't turn off 0x153 keyboard backlight during
+      probe
+    - ixgbe: fix pci device refcount leak
+    - ipv6: raw: Deduct extension header length in rawv6_push_pending_frames
+    - bus: mhi: host: Fix race between channel preparation and M0 event
+    - usb: ulpi: defer ulpi_register on ulpi_read_id timeout
+    - iommu/iova: Fix alloc iova overflows issue
+    - iommu/mediatek-v1: Fix an error handling path in mtk_iommu_v1_probe()
+    - sched/core: Fix use-after-free bug in dup_user_cpus_ptr()
+    - netfilter: ipset: Fix overflow before widen in the bitmap_ip_create()
+      function.
+    - powerpc/imc-pmu: Fix use of mutex in IRQs disabled section
+    - x86/boot: Avoid using Intel mnemonics in AT&T syntax asm
+    - EDAC/device: Fix period calculation in edac_device_reset_delay_period()
+    - x86/resctrl: Fix task CLOSID/RMID update race
+    - regulator: da9211: Use irq handler when ready
+    - scsi: mpi3mr: Refer CONFIG_SCSI_MPI3MR in Makefile
+    - scsi: ufs: Stop using the clock scaling lock in the error handler
+    - scsi: ufs: core: WLUN suspend SSU/enter hibern8 fail recovery
+    - ASoC: wm8904: fix wrong outputs volume after power reactivation
+    - ALSA: usb-audio: Make sure to stop endpoints before closing EPs
+    - ALSA: usb-audio: Relax hw constraints for implicit fb sync
+    - tipc: fix unexpected link reset due to discovery messages
+    - octeontx2-af: Fix LMAC config in cgx_lmac_rx_tx_enable
+    - hvc/xen: lock console list traversal
+    - nfc: pn533: Wait for out_urb's completion in pn533_usb_send_frame()
+    - af_unix: selftest: Fix the size of the parameter to connect()
+    - tools/nolibc: x86: Remove `r8`, `r9` and `r10` from the clobber list
+    - tools/nolibc: x86-64: Use `mov $60,%eax` instead of `mov $60,%rax`
+    - tools/nolibc: use pselect6 on RISCV
+    - tools/nolibc/std: move the standard type definitions to std.h
+    - tools/nolibc/types: split syscall-specific definitions into their own files
+    - tools/nolibc/arch: split arch-specific code into individual files
+    - tools/nolibc/arch: mark the _start symbol as weak
+    - tools/nolibc: Remove .global _start from the entry point code
+    - tools/nolibc: restore mips branch ordering in the _start block
+    - tools/nolibc: fix the O_* fcntl/open macro definitions for riscv
+    - net/sched: act_mpls: Fix warning during failed attribute validation
+    - net/mlx5: Fix ptp max frequency adjustment range
+    - net/mlx5e: Don't support encap rules with gbp option
+    - perf build: Properly guard libbpf includes
+    - igc: Fix PPS delta between two synchronized end-points
+    - platform/surface: aggregator: Add missing call to ssam_request_sync_free()
+    - Documentation: KVM: add API issues section
+    - KVM: x86: Do not return host topology information from
+      KVM_GET_SUPPORTED_CPUID
+    - io_uring: lock overflowing for IOPOLL
+    - arm64: atomics: format whitespace consistently
+    - arm64: atomics: remove LL/SC trampolines
+    - arm64: cmpxchg_double*: hazard against entire exchange variable
+    - efi: fix NULL-deref in init error path
+    - io_uring/io-wq: free worker if task_work creation is canceled
+    - io_uring/io-wq: only free worker if it was allocated for creation
+    - block: handle bio_split_to_limits() NULL return
+    - Revert "usb: ulpi: defer ulpi_register on ulpi_read_id timeout"
+    - pinctrl: amd: Add dynamic debugging for active GPIOs
+    - Linux 5.15.89
+  * Jammy update: v5.15.88 upstream stable release (LP: #2008927)
+    - parisc: Align parisc MADV_XXX constants with all other architectures
+    - serial: fixup backport of "serial: Deassert Transmit Enable on probe in
+      driver-specific way"
+    - net: sched: disallow noqueue for qdisc classes
+    - ALSA: hda/hdmi: Add a HP device 0x8715 to force connect list
+    - ALSA: hda - Enable headset mic on another Dell laptop with ALC3254
+    - Linux 5.15.88
+  * Fix selftests/ftracetests/Meta-selftests (LP: #2006453)
+    - selftests/ftrace: Fix bash specific "==" operator
+
+  [ Ubuntu: 5.15.0-69.76 ]
+
+  * jammy/linux: 5.15.0-69.76 -proposed tracker (LP: #2012092)
+  * NFS deathlock with last Kernel 5.4.0-144.161 and 5.15.0-67.74 (LP: #2009325)
+    - NFS: Correct timing for assigning access cache timestamp
+
+  [ Ubuntu: 5.15.0-68.75 ]
+
+  * jammy/linux: 5.15.0-68.75 -proposed tracker (LP: #2008349)
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2023.02.27)
+  * Ubuntu 22.04 kernel 5.15.0-46-generic leaks kernel memory in kmalloc-2k
+    slabs (LP: #1987430)
+    - SAUCE: audit: fix memory leak of audit_log_lsm()
+  * [EGS] Backport intel_idle support for Eagle Stream Ubuntu 22.04 release
+    (LP: #2003267)
+    - intel_idle: add SPR support
+    - intel_idle: add 'preferred_cstates' module argument
+    - intel_idle: add core C6 optimization for SPR
+    - cpuidle: intel_idle: Drop redundant backslash at line end
+    - intel_idle: Fix the 'preferred_cstates' module parameter
+    - intel_idle: Fix SPR C6 optimization
+    - intel_idle: make SPR C1 and C1E be independent
+  * Fix speaker mute hotkey doesn't work on Dell G16 series (LP: #2003161)
+    - platform/x86: dell-wmi: Add a keymap for KEY_MUTE in type 0x0010 table
+  * Fix the ACPI _CPC not found error from kernel dmesg on some dynamic SSDT
+    table loaded firmwares (LP: #2006077)
+    - ACPI: bus: Avoid using CPPC if not supported by firmware
+    - ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
+    - ACPI: CPPC: Only probe for _CPC if CPPC v2 is acked
+  * rtcpie in timers from ubuntu_kernel_selftests randomly failing
+    (LP: #1814234)
+    - SAUCE: selftest: rtcpie: Force passing unreliable subtest
+  * Jammy update: v5.15.87 upstream stable release (LP: #2007441)
+    - usb: dwc3: qcom: Fix memory leak in dwc3_qcom_interconnect_init
+    - cifs: fix oops during encryption
+    - nvme-pci: fix doorbell buffer value endianness
+    - nvme-pci: fix mempool alloc size
+    - nvme-pci: fix page size checks
+    - ACPI: resource: do IRQ override on LENOVO IdeaPad
+    - ACPI: resource: do IRQ override on XMG Core 15
+    - ACPI: resource: do IRQ override on Lenovo 14ALC7
+    - block, bfq: fix uaf for bfqq in bfq_exit_icq_bfqq
+    - ata: ahci: Fix PCS quirk application for suspend
+    - nvme: fix the NVME_CMD_EFFECTS_CSE_MASK definition
+    - nvmet: don't defer passthrough commands with trivial effects to the
+      workqueue
+    - fs/ntfs3: Validate BOOT record_size
+    - fs/ntfs3: Add overflow check for attribute size
+    - fs/ntfs3: Validate data run offset
+    - fs/ntfs3: Add null pointer check to attr_load_runs_vcn
+    - fs/ntfs3: Fix memory leak on ntfs_fill_super() error path
+    - fs/ntfs3: Add null pointer check for inode operations
+    - fs/ntfs3: Validate attribute name offset
+    - fs/ntfs3: Validate buffer length while parsing index
+    - fs/ntfs3: Validate resident attribute name
+    - fs/ntfs3: Fix slab-out-of-bounds read in run_unpack
+    - soundwire: dmi-quirks: add quirk variant for LAPBC710 NUC15
+    - fs/ntfs3: Validate index root when initialize NTFS security
+    - fs/ntfs3: Use __GFP_NOWARN allocation at wnd_init()
+    - fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_fill_super()
+    - fs/ntfs3: Delete duplicate condition in ntfs_read_mft()
+    - fs/ntfs3: Fix slab-out-of-bounds in r_page
+    - objtool: Fix SEGFAULT
+    - powerpc/rtas: avoid device tree lookups in rtas_os_term()
+    - powerpc/rtas: avoid scheduling in rtas_os_term()
+    - HID: multitouch: fix Asus ExpertBook P2 P2451FA trackpoint
+    - HID: plantronics: Additional PIDs for double volume key presses quirk
+    - pstore: Properly assign mem_type property
+    - pstore/zone: Use GFP_ATOMIC to allocate zone buffer
+    - hfsplus: fix bug causing custom uid and gid being unable to be assigned with
+      mount
+    - binfmt: Fix error return code in load_elf_fdpic_binary()
+    - ovl: Use ovl mounter's fsuid and fsgid in ovl_link()
+    - ALSA: line6: correct midi status byte when receiving data from podxt
+    - ALSA: line6: fix stack overflow in line6_midi_transmit
+    - pnode: terminate at peers of source
+    - mfd: mt6360: Add bounds checking in Regmap read/write call-backs
+    - md: fix a crash in mempool_free
+    - mm, compaction: fix fast_isolate_around() to stay within boundaries
+    - f2fs: should put a page when checking the summary info
+    - f2fs: allow to read node block after shutdown
+    - mmc: vub300: fix warning - do not call blocking ops when !TASK_RUNNING
+    - tpm: acpi: Call acpi_put_table() to fix memory leak
+    - tpm: tpm_crb: Add the missed acpi_put_table() to fix memory leak
+    - tpm: tpm_tis: Add the missed acpi_put_table() to fix memory leak
+    - SUNRPC: Don't leak netobj memory when gss_read_proxy_verf() fails
+    - kcsan: Instrument memcpy/memset/memmove with newer Clang
+    - ASoC: Intel/SOF: use set_stream() instead of set_tdm_slots() for HDAudio
+    - ASoC/SoundWire: dai: expand 'stream' concept beyond SoundWire
+    - rcu-tasks: Simplify trc_read_check_handler() atomic operations
+    - net/af_packet: add VLAN support for AF_PACKET SOCK_RAW GSO
+    - net/af_packet: make sure to pull mac header
+    - media: stv0288: use explicitly signed char
+    - soc: qcom: Select REMAP_MMIO for LLCC driver
+    - kest.pl: Fix grub2 menu handling for rebooting
+    - ktest.pl minconfig: Unset configs instead of just removing them
+    - jbd2: use the correct print format
+    - perf/x86/intel/uncore: Disable I/O stacks to PMU mapping on ICX-D
+    - perf/x86/intel/uncore: Clear attr_update properly
+    - arm64: dts: qcom: sdm845-db845c: correct SPI2 pins drive strength
+    - mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K
+    - btrfs: fix resolving backrefs for inline extent followed by prealloc
+    - ARM: ux500: do not directly dereference __iomem
+    - arm64: dts: qcom: sdm850-lenovo-yoga-c630: correct I2C12 pins drive strength
+    - selftests: Use optional USERCFLAGS and USERLDFLAGS
+    - PM/devfreq: governor: Add a private governor_data for governor
+    - cpufreq: Init completion before kobject_init_and_add()
+    - ALSA: patch_realtek: Fix Dell Inspiron Plus 16
+    - ALSA: hda/realtek: Apply dual codec fixup for Dell Latitude laptops
+    - fs: dlm: fix sock release if listen fails
+    - fs: dlm: retry accept() until -EAGAIN or error returns
+    - mptcp: mark ops structures as ro_after_init
+    - mptcp: remove MPTCP 'ifdef' in TCP SYN cookies
+    - dm cache: Fix ABBA deadlock between shrink_slab and dm_cache_metadata_abort
+    - dm thin: Fix ABBA deadlock between shrink_slab and dm_pool_abort_metadata
+    - dm thin: Use last transaction's pmd->root when commit failed
+    - dm thin: resume even if in FAIL mode
+    - dm thin: Fix UAF in run_timer_softirq()
+    - dm integrity: Fix UAF in dm_integrity_dtr()
+    - dm clone: Fix UAF in clone_dtr()
+    - dm cache: Fix UAF in destroy()
+    - dm cache: set needs_check flag after aborting metadata
+    - tracing/hist: Fix out-of-bound write on 'action_data.var_ref_idx'
+    - perf/core: Call LSM hook after copying perf_event_attr
+    - of/kexec: Fix reading 32-bit "linux,initrd-{start,end}" values
+    - KVM: VMX: Resume guest immediately when injecting #GP on ECREATE
+    - KVM: nVMX: Inject #GP, not #UD, if "generic" VMXON CR0/CR4 check fails
+    - KVM: nVMX: Properly expose ENABLE_USR_WAIT_PAUSE control to L1
+    - x86/microcode/intel: Do not retry microcode reloading on the APs
+    - ftrace/x86: Add back ftrace_expected for ftrace bug reports
+    - x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
+    - x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
+    - tracing: Fix race where eprobes can be called before the event
+    - tracing: Fix complicated dependency of CONFIG_TRACER_MAX_TRACE
+    - tracing/hist: Fix wrong return value in parse_action_params()
+    - tracing/probes: Handle system names with hyphens
+    - tracing: Fix infinite loop in tracing_read_pipe on overflowed
+      print_trace_line
+    - staging: media: tegra-video: fix chan->mipi value on error
+    - staging: media: tegra-video: fix device_node use after free
+    - ARM: 9256/1: NWFPE: avoid compiler-generated __aeabi_uldivmod
+    - media: dvb-core: Fix double free in dvb_register_device()
+    - cifs: fix confusing debug message
+    - cifs: fix missing display of three mount options
+    - rtc: ds1347: fix value written to century register
+    - block: mq-deadline: Do not break sequential write streams to zoned HDDs
+    - md/bitmap: Fix bitmap chunk size overflow issues
+    - efi: Add iMac Pro 2017 to uefi skip cert quirk
+    - wifi: wilc1000: sdio: fix module autoloading
+    - ASoC: jz4740-i2s: Handle independent FIFO flush bits
+    - ipu3-imgu: Fix NULL pointer dereference in imgu_subdev_set_selection()
+    - ipmi: fix long wait in unload when IPMI disconnect
+    - mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
+    - ima: Fix a potential NULL pointer access in ima_restore_measurement_list
+    - ipmi: fix use after free in _ipmi_destroy_user()
+    - PCI: Fix pci_device_is_present() for VFs by checking PF
+    - PCI/sysfs: Fix double free in error path
+    - riscv: stacktrace: Fixup ftrace_graph_ret_addr retp argument
+    - riscv: mm: notify remote harts about mmu cache updates
+    - crypto: n2 - add missing hash statesize
+    - driver core: Fix bus_type.match() error handling in __driver_attach()
+    - phy: qcom-qmp-combo: fix sc8180x reset
+    - iommu/amd: Fix ivrs_acpihid cmdline parsing code
+    - remoteproc: core: Do pm_relax when in RPROC_OFFLINE state
+    - parisc: led: Fix potential null-ptr-deref in start_task()
+    - device_cgroup: Roll back to original exceptions after copy failure
+    - drm/connector: send hotplug uevent on connector cleanup
+    - drm/vmwgfx: Validate the box size for the snooped cursor
+    - drm/i915/dsi: fix VBT send packet port selection for dual link DSI
+    - drm/ingenic: Fix missing platform_driver_unregister() call in
+      ingenic_drm_init()
+    - ext4: silence the warning when evicting inode with dioread_nolock
+    - ext4: add inode table check in __ext4_get_inode_loc to aovid possible
+      infinite loop
+    - ext4: remove trailing newline from ext4_msg() message
+    - fs: ext4: initialize fsdata in pagecache_write()
+    - ext4: fix use-after-free in ext4_orphan_cleanup
+    - ext4: fix undefined behavior in bit shift for ext4_check_flag_values
+    - ext4: add EXT4_IGET_BAD flag to prevent unexpected bad inode
+    - ext4: add helper to check quota inums
+    - ext4: fix bug_on in __es_tree_search caused by bad quota inode
+    - ext4: fix reserved cluster accounting in __es_remove_extent()
+    - ext4: check and assert if marking an no_delete evicting inode dirty
+    - ext4: fix bug_on in __es_tree_search caused by bad boot loader inode
+    - ext4: fix leaking uninitialized memory in fast-commit journal
+    - ext4: fix uninititialized value in 'ext4_evict_inode'
+    - ext4: init quota for 'old.inode' in 'ext4_rename'
+    - ext4: fix delayed allocation bug in ext4_clu_mapped for bigalloc + inline
+    - ext4: fix error code return to user-space in ext4_get_branch()
+    - ext4: avoid BUG_ON when creating xattrs
+    - ext4: fix kernel BUG in 'ext4_write_inline_data_end()'
+    - ext4: fix inode leak in ext4_xattr_inode_create() on an error path
+    - ext4: initialize quota before expanding inode in setproject ioctl
+    - ext4: avoid unaccounted block allocation when expanding inode
+    - ext4: allocate extended attribute value in vmalloc area
+    - drm/amdgpu: handle polaris10/11 overlap asics (v2)
+    - block: mq-deadline: Fix dd_finish_request() for zoned devices
+    - tracing: Fix issue of missing one synthetic field
+    - ext4: remove unused enum EXT4_FC_COMMIT_FAILED
+    - ext4: use ext4_debug() instead of jbd_debug()
+    - ext4: introduce EXT4_FC_TAG_BASE_LEN helper
+    - ext4: factor out ext4_fc_get_tl()
+    - ext4: fix potential out of bound read in ext4_fc_replay_scan()
+    - ext4: disable fast-commit of encrypted dir operations
+    - ext4: don't set up encryption key during jbd2 transaction
+    - ext4: add missing validation of fast-commit record lengths
+    - ext4: fix unaligned memory access in ext4_fc_reserve_space()
+    - ext4: fix off-by-one errors in fast-commit block filling
+    - ARM: renumber bits related to _TIF_WORK_MASK
+    - phy: qcom-qmp-combo: fix out-of-bounds clock access
+    - btrfs: replace strncpy() with strscpy()
+    - btrfs: move missing device handling in a dedicate function
+    - btrfs: fix extent map use-after-free when handling missing device in
+      read_one_chunk
+    - x86/mce: Get rid of msr_ops
+    - x86/MCE/AMD: Clear DFR errors found in THR handler
+    - media: s5p-mfc: Fix to handle reference queue during finishing
+    - media: s5p-mfc: Clear workbit to handle error condition
+    - media: s5p-mfc: Fix in register read and write for H264
+    - perf probe: Use dwarf_attr_integrate as generic DWARF attr accessor
+    - perf probe: Fix to get the DW_AT_decl_file and DW_AT_call_file as unsinged
+      data
+    - ravb: Fix "failed to switch device to config mode" message during unbind
+    - ext4: goto right label 'failed_mount3a'
+    - ext4: correct inconsistent error msg in nojournal mode
+    - mbcache: automatically delete entries from cache on freeing
+    - ext4: fix deadlock due to mbcache entry corruption
+    - drm/i915/migrate: don't check the scratch page
+    - drm/i915/migrate: fix offset calculation
+    - drm/i915/migrate: fix length calculation
+    - SUNRPC: ensure the matching upcall is in-flight upon downcall
+    - btrfs: fix an error handling path in btrfs_defrag_leaves()
+    - bpf: pull before calling skb_postpull_rcsum()
+    - drm/panfrost: Fix GEM handle creation ref-counting
+    - netfilter: nf_tables: consolidate set description
+    - netfilter: nf_tables: add function to create set stateful expressions
+    - netfilter: nf_tables: perform type checking for existing sets
+    - vmxnet3: correctly report csum_level for encapsulated packet
+    - netfilter: nf_tables: honor set timeout and garbage collection updates
+    - veth: Fix race with AF_XDP exposing old or uninitialized descriptors
+    - nfsd: shut down the NFSv4 state objects before the filecache
+    - net: hns3: add interrupts re-initialization while doing VF FLR
+    - net: hns3: refactor hns3_nic_reuse_page()
+    - net: hns3: extract macro to simplify ring stats update code
+    - net: hns3: fix miss L3E checking for rx packet
+    - net: hns3: fix VF promisc mode not update when mac table full
+    - net: sched: fix memory leak in tcindex_set_parms
+    - qlcnic: prevent ->dcb use-after-free on qlcnic_dcb_enable() failure
+    - net: dsa: mv88e6xxx: depend on PTP conditionally
+    - nfc: Fix potential resource leaks
+    - vdpa_sim: fix possible memory leak in vdpasim_net_init() and
+      vdpasim_blk_init()
+    - vhost/vsock: Fix error handling in vhost_vsock_init()
+    - vringh: fix range used in iotlb_translate()
+    - vhost: fix range used in translate_desc()
+    - vdpa_sim: fix vringh initialization in vdpasim_queue_ready()
+    - net/mlx5: E-Switch, properly handle ingress tagged packets on VST
+    - net/mlx5: Add forgotten cleanup calls into mlx5_init_once() error path
+    - net/mlx5: Avoid recovery in probe flows
+    - net/mlx5e: IPoIB, Don't allow CQE compression to be turned on by default
+    - net/mlx5e: TC, Refactor mlx5e_tc_add_flow_mod_hdr() to get flow attr
+    - net/mlx5e: Always clear dest encap in neigh-update-del
+    - net/mlx5e: Fix hw mtu initializing at XDP SQ allocation
+    - net: amd-xgbe: add missed tasklet_kill
+    - net: ena: Fix toeplitz initial hash value
+    - net: ena: Don't register memory info on XDP exchange
+    - net: ena: Account for the number of processed bytes in XDP
+    - net: ena: Use bitmask to indicate packet redirection
+    - net: ena: Fix rx_copybreak value update
+    - net: ena: Set default value for RX interrupt moderation
+    - net: ena: Update NUMA TPH hint register upon NUMA node update
+    - net: phy: xgmiitorgmii: Fix refcount leak in xgmiitorgmii_probe
+    - RDMA/mlx5: Fix mlx5_ib_get_hw_stats when used for device
+    - RDMA/mlx5: Fix validation of max_rd_atomic caps for DC
+    - drm/meson: Reduce the FIFO lines held when AFBC is not used
+    - filelock: new helper: vfs_inode_has_locks
+    - ceph: switch to vfs_inode_has_locks() to fix file lock bug
+    - gpio: sifive: Fix refcount leak in sifive_gpio_probe
+    - net: sched: atm: dont intepret cls results when asked to drop
+    - net: sched: cbq: dont intepret cls results when asked to drop
+    - net: sparx5: Fix reading of the MAC address
+    - netfilter: ipset: fix hash:net,port,net hang with /0 subnet
+    - netfilter: ipset: Rework long task execution when adding/deleting entries
+    - perf tools: Fix resources leak in perf_data__open_dir()
+    - drm/imx: ipuv3-plane: Fix overlay plane width
+    - fs/ntfs3: don't hold ni_lock when calling truncate_setsize()
+    - drivers/net/bonding/bond_3ad: return when there's no aggregator
+    - octeontx2-pf: Fix lmtst ID used in aura free
+    - usb: rndis_host: Secure rndis_query check against int overflow
+    - perf stat: Fix handling of --for-each-cgroup with --bpf-counters to match
+      non BPF mode
+    - drm/i915: unpin on error in intel_vgpu_shadow_mm_pin()
+    - caif: fix memory leak in cfctrl_linkup_request()
+    - udf: Fix extension of the last extent in the file
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
+    - nvme: fix multipath crash caused by flush request when blktrace is enabled
+    - io_uring: check for valid register opcode earlier
+    - nvmet: use NVME_CMD_EFFECTS_CSUPP instead of open coding it
+    - nvme: also return I/O command effects from nvme_command_effects
+    - btrfs: check superblock to ensure the fs was not modified at thaw time
+    - x86/kexec: Fix double-free of elf header buffer
+    - nfsd: fix handling of readdir in v4root vs. mount upcall timeout
+    - fbdev: matroxfb: G200eW: Increase max memory from 1 MB to 16 MB
+    - block: don't allow splitting of a REQ_NOWAIT bio
+    - io_uring: fix CQ waiting timeout handling
+    - thermal: int340x: Add missing attribute for data rate base
+    - riscv: uaccess: fix type of 0 variable on error in get_user()
+    - riscv, kprobes: Stricter c.jr/c.jalr decoding
+    - drm/i915/gvt: fix gvt debugfs destroy
+    - drm/i915/gvt: fix vgpu debugfs clean in remove
+    - hfs/hfsplus: use WARN_ON for sanity check
+    - hfs/hfsplus: avoid WARN_ON() for sanity check, use proper error handling
+    - ksmbd: fix infinite loop in ksmbd_conn_handler_loop()
+    - ksmbd: check nt_len to be at least CIFS_ENCPWD_SIZE in
+      ksmbd_decode_ntlmssp_auth_blob
+    - Revert "ACPI: PM: Add support for upcoming AMD uPEP HID AMDI007"
+    - mptcp: dedicated request sock for subflow in v6
+    - mptcp: use proper req destructor for IPv6
+    - ext4: don't allow journal inode to have encrypt flag
+    - selftests: set the BUILD variable to absolute path
+    - btrfs: make thaw time super block check to also verify checksum
+    - net: hns3: fix return value check bug of rx copybreak
+    - mbcache: Avoid nesting of cache->c_list_lock under bit locks
+    - efi: random: combine bootloader provided RNG seed with RNG protocol output
+    - io_uring: Fix unsigned 'res' comparison with zero in io_fixup_rw_res()
+    - drm/mgag200: Fix PLL setup for G200_SE_A rev >=4
+    - Linux 5.15.87
+  * Jammy update: v5.15.87 upstream stable release (LP: #2007441) //
+    CVE-2022-41218 is assigned to those bugs above.
+    - media: dvb-core: Fix UAF due to refcount races at releasing
+  * RaptorLake: Fix the Screen is shaking by onboard HDMI port in mirror mode
+    (LP: #1993561)
+    - drm/i915/display: Drop check for doublescan mode in modevalid
+    - drm/i915/display: Prune Interlace modes for Display >=12
+  * CVE-2023-0266 // CVE-2023-0266 was assigned for this issue.
+    - ALSA: pcm: Move rwsem lock inside snd_ctl_elem_read to prevent UAF
+  * CVE-2022-4382
+    - USB: gadgetfs: Fix race between mounting and unmounting
+  * CVE-2022-2196
+    - KVM: VMX: Execute IBPB on emulated VM-exit when guest has IBRS
+  * ubuntu_kernel_selftests: net:udpgso_bench.sh failed (LP: #1951447)
+    - selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
+  * net:fcnal-test.sh didn't return a non-zero value even with some sub-tests
+    failed (LP: #2006692)
+    - selftests: net/fcnal-test.sh: add exit code
+  * LXD containers using shiftfs on ZFS or TMPFS broken on 5.15.0-48.54
+    (LP: #1990849)
+    - SAUCE: shiftfs: always rely on init_user_ns
+    - [SAUCE] shiftfs: fix -EOVERFLOW inside the container
+  * Regression in ext4 during online resize (LP: #2003816)
+    - ext4: fix bad checksum after online resize
+    - ext4: fix corruption when online resizing a 1K bigalloc fs
+    - SAUCE: Export ext4_superblock_csum function
+    - ext4: fix corrupt backup group descriptors after online resize
+  * Jammy update: v5.15.86 upstream stable release (LP: #2005113)
+    - usb: musb: remove extra check in musb_gadget_vbus_draw
+    - arm64: dts: qcom: ipq6018-cp01-c1: use BLSPI1 pins
+    - arm64: dts: qcom: sm8250-sony-xperia-edo: fix touchscreen bias-disable
+    - arm64: dts: qcom: msm8996: Add MSM8996 Pro support
+    - arm64: dts: qcom: msm8996: fix supported-hw in cpufreq OPP tables
+    - arm64: dts: qcom: msm8996: fix GPU OPP table
+    - ARM: dts: qcom: apq8064: fix coresight compatible
+    - arm64: dts: qcom: sdm630: fix UART1 pin bias
+    - arm64: dts: qcom: sdm845-cheza: fix AP suspend pin bias
+    - arm64: dts: qcom: msm8916: Drop MSS fallback compatible
+    - objtool, kcsan: Add volatile read/write instrumentation to whitelist
+    - ARM: dts: stm32: Drop stm32mp15xc.dtsi from Avenger96
+    - ARM: dts: stm32: Fix AV96 WLAN regulator gpio property
+    - drivers: soc: ti: knav_qmss_queue: Mark knav_acc_firmwares as static
+    - arm64: dts: qcom: pm660: Use unique ADC5_VCOIN address in node name
+    - arm64: dts: qcom: sm8250: correct LPASS pin pull down
+    - soc: qcom: llcc: make irq truly optional
+    - arm64: dts: qcom: Correct QMP PHY child node name
+    - arm64: dts: qcom: sm8150: fix UFS PHY registers
+    - arm64: dts: qcom: sm8250: fix UFS PHY registers
+    - arm64: dts: qcom: sm8350: fix UFS PHY registers
+    - arm64: dts: qcom: sm8250: drop bogus DP PHY clock
+    - soc: qcom: apr: make code more reuseable
+    - soc: qcom: apr: Add check for idr_alloc and of_property_read_string_index
+    - arm64: dts: qcom: sm6125: fix SDHCI CQE reg names
+    - arm: dts: spear600: Fix clcd interrupt
+    - soc: ti: knav_qmss_queue: Use pm_runtime_resume_and_get instead of
+      pm_runtime_get_sync
+    - soc: ti: knav_qmss_queue: Fix PM disable depth imbalance in knav_queue_probe
+    - soc: ti: smartreflex: Fix PM disable depth imbalance in omap_sr_probe
+    - arm64: Treat ESR_ELx as a 64-bit register
+    - arm64: mm: kfence: only handle translation faults
+    - perf: arm_dsu: Fix hotplug callback leak in dsu_pmu_init()
+    - perf/arm_dmc620: Fix hotplug callback leak in dmc620_pmu_init()
+    - perf/smmuv3: Fix hotplug callback leak in arm_smmu_pmu_init()
+    - arm64: dts: ti: k3-am65-main: Drop dma-coherent in crypto node
+    - arm64: dts: ti: k3-j721e-main: Drop dma-coherent in crypto node
+    - ARM: dts: nuvoton: Remove bogus unit addresses from fixed-partition nodes
+    - arm64: dts: mt6779: Fix devicetree build warnings
+    - arm64: dts: mt2712e: Fix unit_address_vs_reg warning for oscillators
+    - arm64: dts: mt2712e: Fix unit address for pinctrl node
+    - arm64: dts: mt2712-evb: Fix vproc fixed regulators unit names
+    - arm64: dts: mt2712-evb: Fix usb vbus regulators unit names
+    - arm64: dts: mediatek: pumpkin-common: Fix devicetree warnings
+    - arm64: dts: mediatek: mt6797: Fix 26M oscillator unit name
+    - ARM: dts: dove: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-370: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-xp: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-375: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-38x: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-39x: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: turris-omnia: Add ethernet aliases
+    - ARM: dts: turris-omnia: Add switch port 6 node
+    - arm64: dts: armada-3720-turris-mox: Add missing interrupt for RTC
+    - seccomp: Move copy_seccomp() to no failure path.
+    - pstore/ram: Fix error return code in ramoops_probe()
+    - ARM: mmp: fix timer_read delay
+    - pstore: Avoid kcore oops by vmap()ing with VM_IOREMAP
+    - tpm/tpm_ftpm_tee: Fix error handling in ftpm_mod_init()
+    - tpm/tpm_crb: Fix error message in __crb_relinquish_locality()
+    - ovl: store lower path in ovl_inode
+    - ovl: use ovl_copy_{real,upper}attr() wrappers
+    - ovl: remove privs in ovl_copyfile()
+    - ovl: remove privs in ovl_fallocate()
+    - sched/fair: Cleanup task_util and capacity type
+    - sched/uclamp: Fix relationship between uclamp and migration margin
+    - sched/uclamp: Make task_fits_capacity() use util_fits_cpu()
+    - sched/uclamp: Make select_idle_capacity() use util_fits_cpu()
+    - sched/fair: Removed useless update of p->recent_used_cpu
+    - sched/core: Introduce sched_asym_cpucap_active()
+    - sched/uclamp: Make asym_fits_capacity() use util_fits_cpu()
+    - cpuidle: dt: Return the correct numbers of parsed idle states
+    - alpha: fix TIF_NOTIFY_SIGNAL handling
+    - alpha: fix syscall entry in !AUDUT_SYSCALL case
+    - x86/sgx: Reduce delay and interference of enclave release
+    - PM: hibernate: Fix mistake in kerneldoc comment
+    - fs: don't audit the capability check in simple_xattr_list()
+    - cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut()
+    - selftests/ftrace: event_triggers: wait longer for test_event_enable
+    - perf: Fix possible memleak in pmu_dev_alloc()
+    - lib/debugobjects: fix stat count and optimize debug_objects_mem_init
+    - platform/x86: huawei-wmi: fix return value calculation
+    - timerqueue: Use rb_entry_safe() in timerqueue_getnext()
+    - proc: fixup uptime selftest
+    - lib/fonts: fix undefined behavior in bit shift for get_default_font
+    - ocfs2: fix memory leak in ocfs2_stack_glue_init()
+    - MIPS: vpe-mt: fix possible memory leak while module exiting
+    - MIPS: vpe-cmp: fix possible memory leak while module exiting
+    - selftests/efivarfs: Add checking of the test return value
+    - PNP: fix name memory leak in pnp_alloc_dev()
+    - perf/x86/intel/uncore: Fix reference count leak in sad_cfg_iio_topology()
+    - perf/x86/intel/uncore: Fix reference count leak in hswep_has_limit_sbox()
+    - perf/x86/intel/uncore: Fix reference count leak in snr_uncore_mmio_map()
+    - perf/x86/intel/uncore: Fix reference count leak in __uncore_imc_init_box()
+    - platform/chrome: cros_usbpd_notify: Fix error handling in
+      cros_usbpd_notify_init()
+    - thermal: core: fix some possible name leaks in error paths
+    - irqchip: gic-pm: Use pm_runtime_resume_and_get() in gic_probe()
+    - irqchip/wpcm450: Fix memory leak in wpcm450_aic_of_init()
+    - EDAC/i10nm: fix refcount leak in pci_get_dev_wrapper()
+    - SUNRPC: Return true/false (not 1/0) from bool functions
+    - NFSD: Finish converting the NFSv2 GETACL result encoder
+    - nfsd: don't call nfsd_file_put from client states seqfile display
+    - genirq/irqdesc: Don't try to remove non-existing sysfs files
+    - cpufreq: amd_freq_sensitivity: Add missing pci_dev_put()
+    - libfs: add DEFINE_SIMPLE_ATTRIBUTE_SIGNED for signed value
+    - lib/notifier-error-inject: fix error when writing -errno to debugfs file
+    - debugfs: fix error when writing negative value to atomic_t debugfs file
+    - rapidio: fix possible name leaks when rio_add_device() fails
+    - rapidio: rio: fix possible name leak in rio_register_mport()
+    - clocksource/drivers/sh_cmt: Access registers according to spec
+    - mips: ralink: mt7621: define MT7621_SYSC_BASE with __iomem
+    - mips: ralink: mt7621: soc queries and tests as functions
+    - mips: ralink: mt7621: do not use kzalloc too early
+    - futex: Move to kernel/futex/
+    - futex: Resend potentially swallowed owner death notification
+    - cpu/hotplug: Make target_store() a nop when target == state
+    - cpu/hotplug: Do not bail-out in DYING/STARTING sections
+    - clocksource/drivers/timer-ti-dm: Fix missing clk_disable_unprepare in
+      dmtimer_systimer_init_clock()
+    - ACPICA: Fix use-after-free in acpi_ut_copy_ipackage_to_ipackage()
+    - uprobes/x86: Allow to probe a NOP instruction with 0x66 prefix
+    - x86/xen: Fix memory leak in xen_smp_intr_init{_pv}()
+    - x86/xen: Fix memory leak in xen_init_lock_cpu()
+    - xen/privcmd: Fix a possible warning in privcmd_ioctl_mmap_resource()
+    - PM: runtime: Do not call __rpm_callback() from rpm_idle()
+    - platform/chrome: cros_ec_typec: Cleanup switch handle return paths
+    - platform/chrome: cros_ec_typec: zero out stale pointers
+    - platform/x86: mxm-wmi: fix memleak in mxm_wmi_call_mx[ds|mx]()
+    - platform/x86: intel_scu_ipc: fix possible name leak in
+      __intel_scu_ipc_register()
+    - MIPS: BCM63xx: Add check for NULL for clk in clk_enable
+    - MIPS: OCTEON: warn only once if deprecated link status is being used
+    - lockd: set other missing fields when unlocking files
+    - fs: sysv: Fix sysv_nblocks() returns wrong value
+    - rapidio: fix possible UAF when kfifo_alloc() fails
+    - eventfd: change int to __u64 in eventfd_signal() ifndef CONFIG_EVENTFD
+    - relay: fix type mismatch when allocating memory in relay_create_buf()
+    - hfs: Fix OOB Write in hfs_asc2mac
+    - rapidio: devices: fix missing put_device in mport_cdev_open
+    - platform/mellanox: mlxbf-pmc: Fix event typo
+    - wifi: ath9k: hif_usb: fix memory leak of urbs in
+      ath9k_hif_usb_dealloc_tx_urbs()
+    - wifi: ath9k: hif_usb: Fix use-after-free in ath9k_hif_usb_reg_in_cb()
+    - wifi: rtl8xxxu: Fix reading the vendor of combo chips
+    - drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge
+    - libbpf: Fix use-after-free in btf_dump_name_dups
+    - libbpf: Fix null-pointer dereference in find_prog_by_sec_insn()
+    - ata: libata: move ata_{port,link,dev}_dbg to standard pr_XXX() macros
+    - ata: add/use ata_taskfile::{error|status} fields
+    - ata: libata: fix NCQ autosense logic
+    - ipmi: kcs: Poll OBF briefly to reduce OBE latency
+    - drm/amdgpu/powerplay/psm: Fix memory leak in power state init
+    - media: v4l2-ctrls: Fix off-by-one error in integer menu control check
+    - media: coda: jpeg: Add check for kmalloc
+    - media: adv748x: afe: Select input port when initializing AFE
+    - media: i2c: ad5820: Fix error path
+    - venus: pm_helpers: Fix error check in vcodec_domains_get()
+    - soreuseport: Fix socket selection for SO_INCOMING_CPU.
+    - media: exynos4-is: don't rely on the v4l2_async_subdev internals
+    - libbpf: Btf dedup identical struct test needs check for nested
+      structs/arrays
+    - can: kvaser_usb: do not increase tx statistics when sending error message
+      frames
+    - can: kvaser_usb: kvaser_usb_leaf: Get capabilities from device
+    - can: kvaser_usb: kvaser_usb_leaf: Rename {leaf,usbcan}_cmd_error_event to
+      {leaf,usbcan}_cmd_can_error_event
+    - can: kvaser_usb: kvaser_usb_leaf: Handle CMD_ERROR_EVENT
+    - can: kvaser_usb_leaf: Set Warning state even without bus errors
+    - can: kvaser_usb: make use of units.h in assignment of frequency
+    - can: kvaser_usb_leaf: Fix improved state not being reported
+    - can: kvaser_usb_leaf: Fix wrong CAN state after stopping
+    - can: kvaser_usb_leaf: Fix bogus restart events
+    - can: kvaser_usb: Add struct kvaser_usb_busparams
+    - can: kvaser_usb: Compare requested bittiming parameters with actual
+      parameters in do_set_{,data}_bittiming
+    - drm/rockchip: lvds: fix PM usage counter unbalance in poweron
+    - clk: renesas: r9a06g032: Repair grave increment error
+    - spi: Update reference to struct spi_controller
+    - drm/panel/panel-sitronix-st7701: Remove panel on DSI attach failure
+    - drm/msm/hdmi: drop unused GPIO support
+    - drm/msm/hdmi: use devres helper for runtime PM management
+    - bpf: Fix slot type check in check_stack_write_var_off
+    - media: vivid: fix compose size exceed boundary
+    - media: platform: exynos4-is: fix return value check in fimc_md_probe()
+    - bpf: propagate precision in ALU/ALU64 operations
+    - bpf: Check the other end of slot_type for STACK_SPILL
+    - bpf: propagate precision across all frames, not just the last one
+    - clk: qcom: gcc-sm8250: Use retention mode for USB GDSCs
+    - mtd: Fix device name leak when register device failed in add_mtd_device()
+    - Input: joystick - fix Kconfig warning for JOYSTICK_ADC
+    - wifi: rsi: Fix handling of 802.3 EAPOL frames sent via control port
+    - media: camss: Clean up received buffers on failed start of streaming
+    - net, proc: Provide PROC_FS=n fallback for proc_create_net_single_write()
+    - rxrpc: Fix ack.bufferSize to be 0 when generating an ack
+    - bfq: fix waker_bfqq inconsistency crash
+    - drm/radeon: Add the missed acpi_put_table() to fix memory leak
+    - drm/mediatek: Modify dpi power on/off sequence.
+    - ASoC: pxa: fix null-pointer dereference in filter()
+    - libbpf: Fix uninitialized warning in btf_dump_dump_type_data
+    - nvmet: only allocate a single slab for bvecs
+    - regulator: core: fix unbalanced of node refcount in regulator_dev_lookup()
+    - amdgpu/pm: prevent array underflow in vega20_odn_edit_dpm_table()
+    - nvme: return err on nvme_init_non_mdts_limits fail
+    - regulator: qcom-rpmh: Fix PMR735a S3 regulator spec
+    - drm/fourcc: Add packed 10bit YUV 4:2:0 format
+    - drm/fourcc: Fix vsub/hsub for Q410 and Q401
+    - integrity: Fix memory leakage in keyring allocation error path
+    - ima: Fix misuse of dereference of pointer in template_desc_init_fields()
+    - block: clear ->slave_dir when dropping the main slave_dir reference
+    - wifi: ath10k: Fix return value in ath10k_pci_init()
+    - drm/msm/a6xx: Fix speed-bin detection vs probe-defer
+    - mtd: lpddr2_nvm: Fix possible null-ptr-deref
+    - Input: elants_i2c - properly handle the reset GPIO when power is off
+    - media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init()
+    - media: solo6x10: fix possible memory leak in solo_sysfs_init()
+    - media: platform: exynos4-is: Fix error handling in fimc_md_init()
+    - media: videobuf-dma-contig: use dma_mmap_coherent
+    - inet: add READ_ONCE(sk->sk_bound_dev_if) in inet_csk_bind_conflict()
+    - mtd: spi-nor: hide jedec_id sysfs attribute if not present
+    - mtd: spi-nor: Fix the number of bytes for the dummy cycles
+    - bpf: Move skb->len == 0 checks into __bpf_redirect
+    - HID: hid-sensor-custom: set fixed size for custom attributes
+    - pinctrl: k210: call of_node_put()
+    - ALSA: pcm: fix undefined behavior in bit shift for SNDRV_PCM_RATE_KNOT
+    - ALSA: seq: fix undefined behavior in bit shift for
+      SNDRV_SEQ_FILTER_USE_EVENT
+    - regulator: core: use kfree_const() to free space conditionally
+    - clk: rockchip: Fix memory leak in rockchip_clk_register_pll()
+    - drm/amdgpu: fix pci device refcount leak
+    - bonding: fix link recovery in mode 2 when updelay is nonzero
+    - mtd: maps: pxa2xx-flash: fix memory leak in probe
+    - drbd: remove call to memset before free device/resource/connection
+    - drbd: destroy workqueue when drbd device was freed
+    - ASoC: qcom: Add checks for devm_kcalloc
+    - media: vimc: Fix wrong function called when vimc_init() fails
+    - media: imon: fix a race condition in send_packet()
+    - clk: imx8mn: rename vpu_pll to m7_alt_pll
+    - clk: imx: replace osc_hdmi with dummy
+    - clk: imx8mn: fix imx8mn_sai2_sels clocks list
+    - clk: imx8mn: fix imx8mn_enet_phy_sels clocks list
+    - pinctrl: pinconf-generic: add missing of_node_put()
+    - media: dvb-core: Fix ignored return value in dvb_register_frontend()
+    - media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()
+    - media: s5p-mfc: Add variant data for MFC v7 hardware for Exynos 3250 SoC
+    - drm/tegra: Add missing clk_disable_unprepare() in tegra_dc_probe()
+    - ASoC: dt-bindings: wcd9335: fix reset line polarity in example
+    - ASoC: mediatek: mtk-btcvsd: Add checks for write and read of mtk_btcvsd_snd
+    - NFSv4.2: Clear FATTR4_WORD2_SECURITY_LABEL when done decoding
+    - NFSv4.2: Fix a memory stomp in decode_attr_security_label
+    - NFSv4.2: Fix initialisation of struct nfs4_label
+    - NFSv4: Fix a credential leak in _nfs4_discover_trunking()
+    - NFSv4: Fix a deadlock between nfs4_open_recover_helper() and delegreturn
+    - NFS: Fix an Oops in nfs_d_automount()
+    - ALSA: asihpi: fix missing pci_disable_device()
+    - wifi: iwlwifi: mvm: fix double free on tx path.
+    - ASoC: mediatek: mt8173: Fix debugfs registration for components
+    - ASoC: mediatek: mt8173: Enable IRQ when pdata is ready
+    - drm/amd/pm/smu11: BACO is supported when it's in BACO state
+    - drm/radeon: Fix PCI device refcount leak in radeon_atrm_get_bios()
+    - drm/amdgpu: Fix PCI device refcount leak in amdgpu_atrm_get_bios()
+    - drm/amdkfd: Fix memory leakage
+    - ASoC: pcm512x: Fix PM disable depth imbalance in pcm512x_probe
+    - netfilter: conntrack: set icmpv6 redirects as RELATED
+    - Input: wistron_btns - disable on UML
+    - bpf, sockmap: Fix repeated calls to sock_put() when msg has more_data
+    - bpf, sockmap: Fix missing BPF_F_INGRESS flag when using apply_bytes
+    - bpf, sockmap: Fix data loss caused by using apply_bytes on ingress redirect
+    - bonding: uninitialized variable in bond_miimon_inspect()
+    - spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
+    - wifi: cfg80211: Fix not unregister reg_pdev when load_builtin_regdb_keys()
+      fails
+    - mt76: stop the radar detector after leaving dfs channel
+    - wifi: mt76: mt7921: fix reporting of TX AGGR histogram
+    - wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
+    - regulator: core: fix module refcount leak in set_supply()
+    - clk: qcom: lpass-sc7180: Fix pm_runtime usage
+    - clk: qcom: clk-krait: fix wrong div2 functions
+    - hsr: Add a rcu-read lock to hsr_forward_skb().
+    - hsr: Avoid double remove of a node.
+    - hsr: Disable netpoll.
+    - hsr: Synchronize sending frames to have always incremented outgoing seq nr.
+    - hsr: Synchronize sequence number updates.
+    - configfs: fix possible memory leak in configfs_create_dir()
+    - regulator: core: fix resource leak in regulator_register()
+    - hwmon: (jc42) Convert register access and caching to regmap/regcache
+    - hwmon: (jc42) Restore the min/max/critical temperatures on resume
+    - bpf, sockmap: fix race in sock_map_free()
+    - ALSA: pcm: Set missing stop_operating flag at undoing trigger start
+    - media: saa7164: fix missing pci_disable_device()
+    - ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
+    - xprtrdma: Fix regbuf data not freed in rpcrdma_req_create()
+    - SUNRPC: Fix missing release socket in rpc_sockname()
+    - NFSv4.x: Fail client initialisation if state manager thread can't run
+    - riscv, bpf: Emit fixed-length instructions for BPF_PSEUDO_FUNC
+    - mmc: alcor: fix return value check of mmc_add_host()
+    - mmc: moxart: fix return value check of mmc_add_host()
+    - mmc: mxcmmc: fix return value check of mmc_add_host()
+    - mmc: pxamci: fix return value check of mmc_add_host()
+    - mmc: rtsx_pci: fix return value check of mmc_add_host()
+    - mmc: rtsx_usb_sdmmc: fix return value check of mmc_add_host()
+    - mmc: toshsd: fix return value check of mmc_add_host()
+    - mmc: vub300: fix return value check of mmc_add_host()
+    - mmc: wmt-sdmmc: fix return value check of mmc_add_host()
+    - mmc: atmel-mci: fix return value check of mmc_add_host()
+    - mmc: omap_hsmmc: fix return value check of mmc_add_host()
+    - mmc: meson-gx: fix return value check of mmc_add_host()
+    - mmc: via-sdmmc: fix return value check of mmc_add_host()
+    - mmc: wbsd: fix return value check of mmc_add_host()
+    - mmc: mmci: fix return value check of mmc_add_host()
+    - mmc: renesas_sdhi: alway populate SCC pointer
+    - memstick: ms_block: Add error handling support for add_disk()
+    - memstick/ms_block: Add check for alloc_ordered_workqueue
+    - mmc: core: Normalize the error handling branch in sd_read_ext_regs()
+    - regulator: qcom-labibb: Fix missing of_node_put() in
+      qcom_labibb_regulator_probe()
+    - media: c8sectpfe: Add of_node_put() when breaking out of loop
+    - media: coda: Add check for dcoda_iram_alloc
+    - media: coda: Add check for kmalloc
+    - clk: samsung: Fix memory leak in _samsung_clk_register_pll()
+    - spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
+    - wifi: rtl8xxxu: Add __packed to struct rtl8723bu_c2h
+    - wifi: rtl8xxxu: Fix the channel width reporting
+    - wifi: brcmfmac: Fix error return code in brcmf_sdio_download_firmware()
+    - blktrace: Fix output non-blktrace event when blk_classic option enabled
+    - bpf: Do not zero-extend kfunc return values
+    - clk: socfpga: Fix memory leak in socfpga_gate_init()
+    - net: vmw_vsock: vmci: Check memcpy_from_msg()
+    - net: defxx: Fix missing err handling in dfx_init()
+    - net: stmmac: selftests: fix potential memleak in stmmac_test_arpoffload()
+    - net: stmmac: fix possible memory leak in stmmac_dvr_probe()
+    - drivers: net: qlcnic: Fix potential memory leak in qlcnic_sriov_init()
+    - of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry()
+      and find_dup_cset_prop()
+    - ethernet: s2io: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: farsync: Fix kmemleak when rmmods farsync
+    - net/tunnel: wait until all sk_user_data reader finish before releasing the
+      sock
+    - net: apple: mace: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: apple: bmac: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: emaclite: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: ethernet: dnet: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - hamradio: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: amd: lance: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - af_unix: call proto_unregister() in the error path in af_unix_init()
+    - net: amd-xgbe: Fix logic around active and passive cables
+    - net: amd-xgbe: Check only the minimum speed for active/passive cables
+    - can: tcan4x5x: Remove invalid write in clear_interrupts
+    - can: m_can: Call the RAM init directly from m_can_chip_config
+    - can: tcan4x5x: Fix use of register error status mask
+    - net: lan9303: Fix read error execution path
+    - ntb_netdev: Use dev_kfree_skb_any() in interrupt context
+    - sctp: sysctl: make extra pointers netns aware
+    - Bluetooth: MGMT: Fix error report for ADD_EXT_ADV_PARAMS
+    - Bluetooth: btintel: Fix missing free skb in btintel_setup_combined()
+    - Bluetooth: btusb: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_qca: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_ll: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_h5: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_bcsp: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_core: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: RFCOMM: don't call kfree_skb() under spin_lock_irqsave()
+    - stmmac: fix potential division by 0
+    - i40e: Fix the inability to attach XDP program on downed interface
+    - net: dsa: tag_8021q: avoid leaking ctx on dsa_tag_8021q_register() error
+      path
+    - apparmor: fix a memleak in multi_transaction_new()
+    - apparmor: fix lockdep warning when removing a namespace
+    - apparmor: Fix abi check to include v8 abi
+    - crypto: hisilicon/qm - fix missing destroy qp_idr
+    - crypto: sun8i-ss - use dma_addr instead u32
+    - crypto: nitrox - avoid double free on error path in nitrox_sriov_init()
+    - scsi: core: Fix a race between scsi_done() and scsi_timeout()
+    - apparmor: Use pointer to struct aa_label for lbs_cred
+    - PCI: dwc: Fix n_fts[] array overrun
+    - RDMA/core: Fix order of nldev_exit call
+    - PCI: pci-epf-test: Register notifier if only core_init_notifier is enabled
+    - f2fs: Fix the race condition of resize flag between resizefs
+    - crypto: rockchip - do not do custom power management
+    - crypto: rockchip - do not store mode globally
+    - crypto: rockchip - add fallback for cipher
+    - crypto: rockchip - add fallback for ahash
+    - crypto: rockchip - better handle cipher key
+    - crypto: rockchip - remove non-aligned handling
+    - crypto: rockchip - rework by using crypto_engine
+    - apparmor: Fix memleak in alloc_ns()
+    - f2fs: fix to invalidate dcc->f2fs_issue_discard in error path
+    - f2fs: fix normal discard process
+    - f2fs: fix to destroy sbi->post_read_wq in error path of f2fs_fill_super()
+    - RDMA/irdma: Report the correct link speed
+    - scsi: qla2xxx: Fix set-but-not-used variable warnings
+    - RDMA/siw: Fix immediate work request flush to completion queue
+    - IB/mad: Don't call to function that might sleep while in atomic context
+    - RDMA/restrack: Release MR restrack when delete
+    - RDMA/core: Make sure "ib_port" is valid when access sysfs node
+    - RDMA/nldev: Return "-EAGAIN" if the cm_id isn't from expected port
+    - RDMA/siw: Set defined status for work completion with undefined status
+    - scsi: scsi_debug: Fix a warning in resp_write_scat()
+    - crypto: ccree - Remove debugfs when platform_driver_register failed
+    - crypto: cryptd - Use request context instead of stack for sub-request
+    - crypto: hisilicon/qm - add missing pci_dev_put() in q_num_set()
+    - RDMA/hns: Repacing 'dseg_len' by macros in fill_ext_sge_inl_data()
+    - RDMA/hns: Fix ext_sge num error when post send
+    - PCI: Check for alloc failure in pci_request_irq()
+    - RDMA/hfi: Decrease PCI device reference count in error path
+    - crypto: ccree - Make cc_debugfs_global_fini() available for module init
+      function
+    - RDMA/hns: fix memory leak in hns_roce_alloc_mr()
+    - RDMA/rxe: Fix NULL-ptr-deref in rxe_qp_do_cleanup() when socket create
+      failed
+    - dt-bindings: imx6q-pcie: Fix clock names for imx6sx and imx8mq
+    - dt-bindings: visconti-pcie: Fix interrupts array max constraints
+    - scsi: hpsa: Fix possible memory leak in hpsa_init_one()
+    - crypto: tcrypt - Fix multibuffer skcipher speed test mem leak
+    - padata: Always leave BHs disabled when running ->parallel()
+    - padata: Fix list iterator in padata_do_serial()
+    - scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add()
+    - scsi: hpsa: Fix error handling in hpsa_add_sas_host()
+    - scsi: hpsa: Fix possible memory leak in hpsa_add_sas_device()
+    - scsi: efct: Fix possible memleak in efct_device_init()
+    - scsi: scsi_debug: Fix a warning in resp_verify()
+    - scsi: scsi_debug: Fix a warning in resp_report_zones()
+    - scsi: fcoe: Fix possible name leak when device_register() fails
+    - scsi: scsi_debug: Fix possible name leak in sdebug_add_host_helper()
+    - scsi: ipr: Fix WARNING in ipr_init()
+    - scsi: fcoe: Fix transport not deattached when fcoe_if_init() fails
+    - scsi: snic: Fix possible UAF in snic_tgt_create()
+    - RDMA/nldev: Add checks for nla_nest_start() in fill_stat_counter_qps()
+    - f2fs: avoid victim selection from previous victim section
+    - RDMA/nldev: Fix failure to send large messages
+    - crypto: amlogic - Remove kcalloc without check
+    - crypto: omap-sham - Use pm_runtime_resume_and_get() in omap_sham_probe()
+    - riscv/mm: add arch hook arch_clear_hugepage_flags
+    - RDMA/hfi1: Fix error return code in parse_platform_config()
+    - RDMA/srp: Fix error return code in srp_parse_options()
+    - PCI: mt7621: Rename mt7621_pci_ to mt7621_pcie_
+    - PCI: mt7621: Add sentinel to quirks table
+    - orangefs: Fix sysfs not cleanup when dev init failed
+    - RDMA/hns: Fix AH attr queried by query_qp
+    - RDMA/hns: Fix PBL page MTR find
+    - RDMA/hns: Fix page size cap from firmware
+    - RDMA/hns: Fix error code of CMD
+    - crypto: img-hash - Fix variable dereferenced before check 'hdev->req'
+    - hwrng: amd - Fix PCI device refcount leak
+    - hwrng: geode - Fix PCI device refcount leak
+    - IB/IPoIB: Fix queue count inconsistency for PKEY child interfaces
+    - RISC-V: Align the shadow stack
+    - drivers: dio: fix possible memory leak in dio_init()
+    - serial: tegra: Read DMA status before terminating
+    - serial: 8250_bcm7271: Fix error handling in brcmuart_init()
+    - class: fix possible memory leak in __class_register()
+    - vfio: platform: Do not pass return buffer to ACPI _RST method
+    - uio: uio_dmem_genirq: Fix missing unlock in irq configuration
+    - uio: uio_dmem_genirq: Fix deadlock between irq config and handling
+    - usb: fotg210-udc: Fix ages old endianness issues
+    - staging: vme_user: Fix possible UAF in tsi148_dma_list_add
+    - usb: typec: Check for ops->exit instead of ops->enter in altmode_exit
+    - usb: typec: tcpci: fix of node refcount leak in tcpci_register_port()
+    - usb: typec: tipd: Cleanup resources if devm_tps6598_psy_register fails
+    - usb: typec: tipd: Fix spurious fwnode_handle_put in error path
+    - extcon: usbc-tusb320: Add support for mode setting and reset
+    - extcon: usbc-tusb320: Add support for TUSB320L
+    - usb: typec: Factor out non-PD fwnode properties
+    - extcon: usbc-tusb320: Factor out extcon into dedicated functions
+    - extcon: usbc-tusb320: Add USB TYPE-C support
+    - extcon: usbc-tusb320: Update state on probe even if no IRQ pending
+    - serial: amba-pl011: avoid SBSA UART accessing DMACR register
+    - serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
+    - serial: stm32: move dma_request_chan() before clk_prepare_enable()
+    - serial: pch: Fix PCI device refcount leak in pch_request_dma()
+    - tty: serial: clean up stop-tx part in altera_uart_tx_chars()
+    - tty: serial: altera_uart_{r,t}x_chars() need only uart_port
+    - serial: altera_uart: fix locking in polling mode
+    - serial: sunsab: Fix error handling in sunsab_init()
+    - test_firmware: fix memory leak in test_firmware_init()
+    - misc: ocxl: fix possible name leak in ocxl_file_register_afu()
+    - ocxl: fix pci device refcount leak when calling get_function_0()
+    - misc: tifm: fix possible memory leak in tifm_7xx1_switch_media()
+    - misc: sgi-gru: fix use-after-free error in gru_set_context_option, gru_fault
+      and gru_handle_user_call_os
+    - firmware: raspberrypi: fix possible memory leak in rpi_firmware_probe()
+    - cxl: fix possible null-ptr-deref in cxl_guest_init_afu|adapter()
+    - cxl: fix possible null-ptr-deref in cxl_pci_init_afu|adapter()
+    - iio: temperature: ltc2983: make bulk write buffer DMA-safe
+    - iio: adis: handle devices that cannot unmask the drdy pin
+    - iio: adis: stylistic changes
+    - iio:imu:adis: Move exports into IIO_ADISLIB namespace
+    - iio: adis: add '__adis_enable_irq()' implementation
+    - counter: stm32-lptimer-cnt: fix the check on arr and cmp registers update
+    - coresight: trbe: remove cpuhp instance node before remove cpuhp state
+    - usb: roles: fix of node refcount leak in usb_role_switch_is_parent()
+    - usb: gadget: f_hid: fix f_hidg lifetime vs cdev
+    - usb: gadget: f_hid: fix refcount leak on error path
+    - drivers: mcb: fix resource leak in mcb_probe()
+    - mcb: mcb-parse: fix error handing in chameleon_parse_gdd()
+    - chardev: fix error handling in cdev_device_add()
+    - i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
+    - staging: rtl8192u: Fix use after free in ieee80211_rx()
+    - staging: rtl8192e: Fix potential use-after-free in rtllib_rx_Monitor()
+    - vme: Fix error not catched in fake_init()
+    - gpiolib: Get rid of redundant 'else'
+    - gpiolib: cdev: fix NULL-pointer dereferences
+    - gpiolib: make struct comments into real kernel docs
+    - gpiolib: protect the GPIO device against being dropped while in use by user-
+      space
+    - i2c: mux: reg: check return value after calling platform_get_resource()
+    - i2c: ismt: Fix an out-of-bounds bug in ismt_access()
+    - usb: storage: Add check for kcalloc
+    - tracing/hist: Fix issue of losting command info in error_log
+    - ksmbd: Fix resource leak in ksmbd_session_rpc_open()
+    - samples: vfio-mdev: Fix missing pci_disable_device() in mdpy_fb_probe()
+    - thermal/drivers/imx8mm_thermal: Validate temperature range
+    - thermal/drivers/qcom/temp-alarm: Fix inaccurate warning for gen2
+    - thermal/drivers/qcom/lmh: Fix irq handler return value
+    - fbdev: ssd1307fb: Drop optional dependency
+    - fbdev: pm2fb: fix missing pci_disable_device()
+    - fbdev: via: Fix error in via_core_init()
+    - fbdev: vermilion: decrease reference count in error path
+    - fbdev: ep93xx-fb: Add missing clk_disable_unprepare in ep93xxfb_probe()
+    - fbdev: geode: don't build on UML
+    - fbdev: uvesafb: don't build on UML
+    - fbdev: uvesafb: Fixes an error handling path in uvesafb_probe()
+    - HSI: omap_ssi_core: fix unbalanced pm_runtime_disable()
+    - HSI: omap_ssi_core: fix possible memory leak in ssi_probe()
+    - power: supply: fix residue sysfs file in error handle route of
+      __power_supply_register()
+    - perf trace: Return error if a system call doesn't exist
+    - perf trace: Use macro RAW_SYSCALL_ARGS_NUM to replace number
+    - perf trace: Handle failure when trace point folder is missed
+    - perf symbol: correction while adjusting symbol
+    - power: supply: z2_battery: Fix possible memleak in z2_batt_probe()
+    - HSI: omap_ssi_core: Fix error handling in ssi_init()
+    - power: supply: ab8500: Fix error handling in ab8500_charger_init()
+    - power: supply: fix null pointer dereferencing in
+      power_supply_get_battery_info
+    - perf stat: Refactor __run_perf_stat() common code
+    - perf stat: Do not delay the workload with --delay
+    - RDMA/siw: Fix pointer cast warning
+    - fs/ntfs3: Avoid UBSAN error on true_sectors_per_clst()
+    - overflow: Implement size_t saturating arithmetic helpers
+    - fs/ntfs3: Harden against integer overflows
+    - iommu/sun50i: Fix reset release
+    - iommu/sun50i: Consider all fault sources for reset
+    - iommu/sun50i: Fix R/W permission check
+    - iommu/sun50i: Fix flush size
+    - iommu/rockchip: fix permission bits in page table entries v2
+    - phy: usb: s2 WoL wakeup_count not incremented for USB->Eth devices
+    - include/uapi/linux/swab: Fix potentially missing __always_inline
+    - pwm: tegra: Improve required rate calculation
+    - fs/ntfs3: Fix slab-out-of-bounds read in ntfs_trim_fs
+    - dmaengine: idxd: Fix crc_val field for completion record
+    - rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0
+    - rtc: cmos: Fix event handler registration ordering issue
+    - rtc: cmos: Fix wake alarm breakage
+    - rtc: cmos: fix build on non-ACPI platforms
+    - rtc: cmos: Call cmos_wake_setup() from cmos_do_probe()
+    - rtc: cmos: Call rtc_wake_setup() from cmos_do_probe()
+    - rtc: cmos: Eliminate forward declarations of some functions
+    - rtc: cmos: Rename ACPI-related functions
+    - rtc: cmos: Disable ACPI RTC event on removal
+    - rtc: snvs: Allow a time difference on clock register read
+    - rtc: pcf85063: Fix reading alarm
+    - iommu/amd: Fix pci device refcount leak in ppr_notifier()
+    - iommu/fsl_pamu: Fix resource leak in fsl_pamu_probe()
+    - macintosh: fix possible memory leak in macio_add_one_device()
+    - macintosh/macio-adb: check the return value of ioremap()
+    - powerpc/52xx: Fix a resource leak in an error handling path
+    - cxl: Fix refcount leak in cxl_calc_capp_routing
+    - powerpc/xmon: Fix -Wswitch-unreachable warning in bpt_cmds
+    - powerpc/xive: add missing iounmap() in error path in
+      xive_spapr_populate_irq_data()
+    - powerpc/perf: callchain validate kernel stack pointer bounds
+    - powerpc/83xx/mpc832x_rdb: call platform_device_put() in error case in
+      of_fsl_spi_probe()
+    - powerpc/hv-gpci: Fix hv_gpci event list
+    - selftests/powerpc: Fix resource leaks
+    - iommu/sun50i: Remove IOMMU_DOMAIN_IDENTITY
+    - pwm: sifive: Call pwm_sifive_update_clock() while mutex is held
+    - pwm: mtk-disp: Fix the parameters calculated by the enabled flag of disp_pwm
+    - pwm: mediatek: always use bus clock for PWM on MT7622
+    - remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()
+    - remoteproc: qcom: q6v5: Fix potential null-ptr-deref in
+      q6v5_wcss_init_mmio()
+    - remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove
+    - remoteproc: qcom_q6v5_pas: detach power domains on remove
+    - remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in
+      adsp_alloc_memory_region()
+    - remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in
+      q6v5_wcss_qcs404_power_on()
+    - powerpc/eeh: Drop redundant spinlock initialization
+    - powerpc/pseries/eeh: use correct API for error log size
+    - mfd: bd957x: Fix Kconfig dependency on REGMAP_IRQ
+    - mfd: qcom_rpm: Fix an error handling path in qcom_rpm_probe()
+    - mfd: pm8008: Remove driver data structure pm8008_data
+    - mfd: pm8008: Fix return value check in pm8008_probe()
+    - netfilter: flowtable: really fix NAT IPv6 offload
+    - rtc: st-lpc: Add missing clk_disable_unprepare in st_rtc_probe()
+    - rtc: pic32: Move devm_rtc_allocate_device earlier in pic32_rtc_probe()
+    - rtc: pcf85063: fix pcf85063_clkout_control
+    - nfsd: under NFSv4.1, fix double svc_xprt_put on rpc_create failure
+    - net: macsec: fix net device access prior to holding a lock
+    - mISDN: hfcsusb: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - mISDN: hfcpci: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - mISDN: hfcmulti: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - block, bfq: fix possible uaf for 'bfqq->bic'
+    - net: enetc: avoid buffer leaks on xdp_do_redirect() failure
+    - nfc: pn533: Clear nfc_target before being used
+    - unix: Fix race in SOCK_SEQPACKET's unix_dgram_sendmsg()
+    - r6040: Fix kmemleak in probe and remove
+    - igc: Enhance Qbv scheduling by using first flag bit
+    - igc: Use strict cycles for Qbv scheduling
+    - igc: Add checking for basetime less than zero
+    - igc: allow BaseTime 0 enrollment for Qbv
+    - igc: recalculate Qbv end_time by considering cycle time
+    - igc: Lift TAPRIO schedule restriction
+    - igc: Set Qbv start_time and end_time to end_time if not being configured in
+      GCL
+    - rtc: mxc_v2: Add missing clk_disable_unprepare()
+    - selftests: devlink: fix the fd redirect in dummy_reporter_test
+    - openvswitch: Fix flow lookup to use unmasked key
+    - soc: mediatek: pm-domains: Fix the power glitch issue
+    - arm64: dts: mt8183: Fix Mali GPU clock
+    - skbuff: Account for tail adjustment during pull operations
+    - mailbox: mpfs: read the system controller's status
+    - mailbox: arm_mhuv2: Fix return value check in mhuv2_probe()
+    - mailbox: zynq-ipi: fix error handling while device_register() fails
+    - net_sched: reject TCF_EM_SIMPLE case for complex ematch module
+    - rxrpc: Fix missing unlock in rxrpc_do_sendmsg()
+    - myri10ge: Fix an error handling path in myri10ge_probe()
+    - net: stream: purge sk_error_queue in sk_stream_kill_queues()
+    - HID: amd_sfh: Add missing check for dma_alloc_coherent
+    - rcu: Fix __this_cpu_read() lockdep warning in rcu_force_quiescent_state()
+    - arm64: make is_ttbrX_addr() noinstr-safe
+    - video: hyperv_fb: Avoid taking busy spinlock on panic path
+    - x86/hyperv: Remove unregister syscore call from Hyper-V cleanup
+    - binfmt_misc: fix shift-out-of-bounds in check_special_flags
+    - fs: jfs: fix shift-out-of-bounds in dbAllocAG
+    - udf: Avoid double brelse() in udf_rename()
+    - jfs: Fix fortify moan in symlink
+    - fs: jfs: fix shift-out-of-bounds in dbDiscardAG
+    - ACPICA: Fix error code path in acpi_ds_call_control_method()
+    - nilfs2: fix shift-out-of-bounds/overflow in nilfs_sb2_bad_offset()
+    - nilfs2: fix shift-out-of-bounds due to too large exponent of block size
+    - acct: fix potential integer overflow in encode_comp_t()
+    - hfs: fix OOB Read in __hfs_brec_find
+    - drm/etnaviv: add missing quirks for GC300
+    - media: imx-jpeg: Disable useless interrupt to avoid kernel panic
+    - brcmfmac: return error when getting invalid max_flowrings from dongle
+    - wifi: ath9k: verify the expected usb_endpoints are present
+    - wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
+    - ASoC: codecs: rt298: Add quirk for KBL-R RVP platform
+    - ipmi: fix memleak when unload ipmi driver
+    - drm/amd/display: prevent memory leak
+    - Revert "drm/amd/display: Limit max DSC target bpp for specific monitors"
+    - qed (gcc13): use u16 for fid to be big enough
+    - bpf: make sure skb->len != 0 when redirecting to a tunneling device
+    - net: ethernet: ti: Fix return type of netcp_ndo_start_xmit()
+    - hamradio: baycom_epp: Fix return type of baycom_send_packet()
+    - wifi: brcmfmac: Fix potential shift-out-of-bounds in
+      brcmf_fw_alloc_request()
+    - igb: Do not free q_vector unless new one was allocated
+    - drm/amdgpu: Fix type of second parameter in trans_msg() callback
+    - drm/amdgpu: Fix type of second parameter in odn_edit_dpm_table() callback
+    - s390/ctcm: Fix return type of ctc{mp,}m_tx()
+    - s390/netiucv: Fix return type of netiucv_tx()
+    - s390/lcs: Fix return type of lcs_start_xmit()
+    - drm/msm: Use drm_mode_copy()
+    - drm/rockchip: Use drm_mode_copy()
+    - drm/sti: Use drm_mode_copy()
+    - drm/mediatek: Fix return type of mtk_hdmi_bridge_mode_valid()
+    - drivers/md/md-bitmap: check the return value of md_bitmap_get_counter()
+    - md/raid1: stop mdx_raid1 thread when raid1 array run failed
+    - drm/amd/display: fix array index out of bound error in bios parser
+    - net: add atomic_long_t to net_device_stats fields
+    - ipv6/sit: use DEV_STATS_INC() to avoid data-races
+    - mrp: introduce active flags to prevent UAF when applicant uninit
+    - ppp: associate skb with a device at tx
+    - bpf: Prevent decl_tag from being referenced in func_proto arg
+    - ethtool: avoiding integer overflow in ethtool_phys_id()
+    - media: dvb-frontends: fix leak of memory fw
+    - media: dvbdev: adopts refcnt to avoid UAF
+    - media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
+    - blk-mq: fix possible memleak when register 'hctx' failed
+    - drm/amd/display: Use the largest vready_offset in pipe group
+    - libbpf: Avoid enum forward-declarations in public API in C++ mode
+    - regulator: core: fix use_count leakage when handling boot-on
+    - wifi: mt76: do not run mt76u_status_worker if the device is not running
+    - mmc: f-sdh30: Add quirks for broken timeout clock capability
+    - mmc: renesas_sdhi: better reset from HS400 mode
+    - media: si470x: Fix use-after-free in si470x_int_in_callback()
+    - clk: st: Fix memory leak in st_of_quadfs_setup()
+    - crypto: hisilicon/hpre - fix resource leak in remove process
+    - scsi: lpfc: Fix hard lockup when reading the rx_monitor from debugfs
+    - scsi: ufs: Reduce the START STOP UNIT timeout
+    - scsi: elx: libefc: Fix second parameter type in state callbacks
+    - hugetlbfs: fix null-ptr-deref in hugetlbfs_parse_param()
+    - drm/fsl-dcu: Fix return type of fsl_dcu_drm_connector_mode_valid()
+    - drm/sti: Fix return type of sti_{dvo,hda,hdmi}_connector_mode_valid()
+    - orangefs: Fix kmemleak in orangefs_prepare_debugfs_help_string()
+    - orangefs: Fix kmemleak in orangefs_{kernel,client}_debug_init()
+    - tools/include: Add _RET_IP_ and math definitions to kernel.h
+    - KVM: selftests: Fix build regression by using accessor function
+    - hwmon: (jc42) Fix missing unlock on error in jc42_write()
+    - ALSA/ASoC: hda: move/rename snd_hdac_ext_stop_streams to hdac_stream.c
+    - ALSA: hda: add snd_hdac_stop_streams() helper
+    - ASoC: Intel: Skylake: Fix driver hang during shutdown
+    - ASoC: mediatek: mt8173-rt5650-rt5514: fix refcount leak in
+      mt8173_rt5650_rt5514_dev_probe()
+    - ASoC: audio-graph-card: fix refcount leak of cpu_ep in
+      __graph_for_each_link()
+    - ASoC: rockchip: pdm: Add missing clk_disable_unprepare() in
+      rockchip_pdm_runtime_resume()
+    - ASoC: mediatek: mt8183: fix refcount leak in
+      mt8183_mt6358_ts3a227_max98357_dev_probe()
+    - ASoC: wm8994: Fix potential deadlock
+    - ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in
+      rk_spdif_runtime_resume()
+    - ASoC: rt5670: Remove unbalanced pm_runtime_put()
+    - drm/i915/display: Don't disable DDI/Transcoder when setting phy test pattern
+    - LoadPin: Ignore the "contents" argument of the LSM hooks
+    - pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion
+    - perf debug: Set debug_peo_args and redirect_to_stderr variable to correct
+      values in perf_quiet_option()
+    - afs: Fix lost servers_outstanding count
+    - pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
+    - ALSA: usb-audio: add the quirk for KT0206 device
+    - ALSA: hda/realtek: Add quirk for Lenovo TianYi510Pro-14IOB
+    - ALSA: hda/hdmi: Add HP Device 0x8711 to force connect list
+    - usb: cdnsp: fix lack of ZLP for ep0
+    - usb: xhci-mtk: fix leakage of shared hcd when fail to set wakeup irq
+    - arm64: dts: qcom: sm8250: fix USB-DP PHY registers
+    - usb: dwc3: Fix race between dwc3_set_mode and __dwc3_set_mode
+    - usb: dwc3: core: defer probe on ulpi_read_id timeout
+    - xhci: Prevent infinite loop in transaction errors recovery for streams
+    - HID: wacom: Ensure bootloader PID is usable in hidraw mode
+    - HID: mcp2221: don't connect hidraw
+    - loop: Fix the max_loop commandline argument treatment when it is set to 0
+    - 9p: set req refcount to zero to avoid uninitialized usage
+    - security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
+    - reiserfs: Add missing calls to reiserfs_security_free()
+    - iio: fix memory leak in iio_device_register_eventset()
+    - iio: adc: ad_sigma_delta: do not use internal iio_dev lock
+    - iio: adc128s052: add proper .data members in adc128_of_match table
+    - regulator: core: fix deadlock on regulator enable
+    - floppy: Fix memory leak in do_floppy_init()
+    - gcov: add support for checksum field
+    - fbdev: fbcon: release buffer when fbcon_do_set_font() failed
+    - ovl: fix use inode directly in rcu-walk mode
+    - btrfs: do not BUG_ON() on ENOMEM when dropping extent items for a range
+    - scsi: qla2xxx: Fix crash when I/O abort times out
+    - net: stmmac: fix errno when create_singlethread_workqueue() fails
+    - media: dvbdev: fix build warning due to comments
+    - media: dvbdev: fix refcnt bug
+    - extcon: usbc-tusb320: Call the Type-C IRQ handler only if a port is
+      registered
+    - mfd: qcom_rpm: Use devm_of_platform_populate() to simplify code
+    - pwm: tegra: Fix 32 bit build
+    - Linux 5.15.86
+  * Screen freeze after resuming from suspend (nvme0: I/O timeout)
+    (LP: #1996048) // Jammy update: v5.15.86 upstream stable release
+    (LP: #2005113)
+    - PCI: vmd: Disable MSI remapping after suspend
+  * CVE-2023-23559
+    - wifi: rndis_wlan: Prevent buffer overflow in rndis_query_oid
+  * CVE-2023-0045
+    - x86/bugs: Flush IBP in ib_prctl_set()
+
+  [ Ubuntu: 5.15.0-67.74 ]
+
+  * jammy/linux: 5.15.0-67.74 -proposed tracker (LP: #2008074)
+  * [Inspiron 7590, Realtek ALC3254, Speaker, Internal] fails after a while
+    (LP: #2007798)
+    - Revert "ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()"
+
+  [ Ubuntu: 5.15.0-66.73 ]
+
+  * jammy/linux: 5.15.0-66.73 -proposed tracker (LP: #2004636)
+  * CVE-2023-0461
+    - SAUCE: Fix inet_csk_listen_start after CVE-2023-0461
+
+  [ Ubuntu: 5.15.0-65.72 ]
+
+  * jammy/linux: 5.15.0-65.72 -proposed tracker (LP: #2004344)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2023.01.30)
+  * NFS: client permission error after adding user to permissible group
+    (LP: #2003053)
+    - NFS: Clear the file access cache upon login
+    - NFS: Judge the file access cache's timestamp in rcu path
+    - NFS: Fix up a sparse warning
+  * Fix W6400 hang after resume of S3 stress (LP: #2000299)
+    - drm/amd/display: Manually adjust strobe for DCN303
+  * Rear Audio port sometimes has no audio output after reboot(Cirrus Logic)
+    (LP: #1998905)
+    - ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
+  * CVE-2022-20369
+    - NFSD: fix use-after-free in __nfs42_ssc_open()
+  * CVE-2023-0461
+    - net/ulp: prevent ULP without clone op from entering the LISTEN status
+    - net/ulp: use consistent error code when blocking ULP
+  * CVE-2023-0179
+    - netfilter: nft_payload: incorrect arithmetics when fetching VLAN header bits
+  * Jammy update: v5.15.85 upstream stable release (LP: #2003139)
+    - udf: Discard preallocation before extending file with a hole
+    - udf: Fix preallocation discarding at indirect extent boundary
+    - udf: Do not bother looking for prealloc extents if i_lenExtents matches
+      i_size
+    - udf: Fix extending file within last block
+    - usb: gadget: uvc: Prevent buffer overflow in setup handler
+    - USB: serial: option: add Quectel EM05-G modem
+    - USB: serial: cp210x: add Kamstrup RF sniffer PIDs
+    - USB: serial: f81232: fix division by zero on line-speed change
+    - USB: serial: f81534: fix division by zero on line-speed change
+    - xhci: Apply XHCI_RESET_TO_DEFAULT quirk to ADL-N
+    - igb: Initialize mailbox message for VF reset
+    - usb: dwc3: pci: Update PCIe device ID for USB3 controller on CPU sub-system
+      for Raptor Lake
+    - HID: uclogic: Add HID_QUIRK_HIDINPUT_FORCE quirk
+    - selftests: net: Use "grep -E" instead of "egrep"
+    - net: loopback: use NET_NAME_PREDICTABLE for name_assign_type
+    - Linux 5.15.85
+  * Jammy update: v5.15.84 upstream stable release (LP: #2003137)
+    - x86/vdso: Conditionally export __vdso_sgx_enter_enclave()
+    - vfs: fix copy_file_range() averts filesystem freeze protection
+    - ASoC: fsl_micfil: explicitly clear software reset bit
+    - ASoC: fsl_micfil: explicitly clear CHnF flags
+    - ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()
+    - libbpf: Use page size as max_entries when probing ring buffer map
+    - pinctrl: meditatek: Startup with the IRQs disabled
+    - can: sja1000: fix size of OCR_MODE_MASK define
+    - can: mcba_usb: Fix termination command argument
+    - net: fec: don't reset irq coalesce settings to defaults on "ip link up"
+    - ASoC: cs42l51: Correct PGA Volume minimum value
+    - perf: Fix perf_pending_task() UaF
+    - nvme-pci: clear the prp2 field when not used
+    - ASoC: ops: Correct bounds check for second channel on SX controls
+    - net: fec: properly guard irq coalesce setup
+    - Linux 5.15.84
+  * Jammy update: v5.15.83 upstream stable release (LP: #2003134)
+    - clk: generalize devm_clk_get() a bit
+    - clk: Provide new devm_clk helpers for prepared and enabled clocks
+    - mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()
+    - arm64: dts: rockchip: keep I2S1 disabled for GPIO function on ROCK Pi 4
+      series
+    - arm: dts: rockchip: fix node name for hym8563 rtc
+    - arm: dts: rockchip: remove clock-frequency from rtc
+    - ARM: dts: rockchip: fix ir-receiver node names
+    - arm64: dts: rockchip: fix ir-receiver node names
+    - ARM: dts: rockchip: rk3188: fix lcdc1-rgb24 node name
+    - fs: use acquire ordering in __fget_light()
+    - ARM: 9251/1: perf: Fix stacktraces for tracepoint events in THUMB2 kernels
+    - ARM: 9266/1: mm: fix no-MMU ZERO_PAGE() implementation
+    - ASoC: wm8962: Wait for updated value of WM8962_CLOCKING1 register
+    - spi: mediatek: Fix DEVAPC Violation at KO Remove
+    - ARM: dts: rockchip: disable arm_global_timer on rk3066 and rk3188
+    - ASoC: rt711-sdca: fix the latency time of clock stop prepare state machine
+      transitions
+    - 9p/fd: Use P9_HDRSZ for header size
+    - regulator: slg51000: Wait after asserting CS pin
+    - ALSA: seq: Fix function prototype mismatch in snd_seq_expand_var_event
+    - selftests/net: Find nettest in current directory
+    - btrfs: send: avoid unaligned encoded writes when attempting to clone range
+    - ASoC: soc-pcm: Add NULL check in BE reparenting
+    - regulator: twl6030: fix get status of twl6032 regulators
+    - fbcon: Use kzalloc() in fbcon_prepare_logo()
+    - usb: dwc3: gadget: Disable GUSB2PHYCFG.SUSPHY for End Transfer
+    - 9p/xen: check logical size for buffer size
+    - net: usb: qmi_wwan: add u-blox 0x1342 composition
+    - mm/khugepaged: take the right locks for page table retraction
+    - mm/khugepaged: fix GUP-fast interaction by sending IPI
+    - mm/khugepaged: invoke MMU notifiers in shmem/file collapse paths
+    - rtc: mc146818-lib: extract mc146818_avoid_UIP
+    - rtc: cmos: avoid UIP when writing alarm time
+    - rtc: cmos: avoid UIP when reading alarm time
+    - cifs: fix use-after-free caused by invalid pointer `hostname`
+    - drm/bridge: anx7625: Fix edid_read break case in sp_tx_edid_read()
+    - xen/netback: do some code cleanup
+    - xen/netback: don't call kfree_skb() with interrupts disabled
+    - media: videobuf2-core: take mmap_lock in vb2_get_unmapped_area()
+    - soundwire: intel: Initialize clock stop timeout
+    - media: v4l2-dv-timings.c: fix too strict blanking sanity checks
+    - memcg: fix possible use-after-free in memcg_write_event_control()
+    - mm/gup: fix gup_pud_range() for dax
+    - Bluetooth: btusb: Add debug message for CSR controllers
+    - Bluetooth: Fix crash when replugging CSR fake controllers
+    - net: mana: Fix race on per-CQ variable napi work_done
+    - KVM: s390: vsie: Fix the initialization of the epoch extension (epdx) field
+    - drm/vmwgfx: Don't use screen objects when SEV is active
+    - drm/amdgpu/sdma_v4_0: turn off SDMA ring buffer in the s2idle suspend
+    - drm/shmem-helper: Remove errant put in error path
+    - drm/shmem-helper: Avoid vm_open error paths
+    - net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
+    - HID: usbhid: Add ALWAYS_POLL quirk for some mice
+    - HID: hid-lg4ff: Add check for empty lbuf
+    - HID: core: fix shift-out-of-bounds in hid_report_raw_event
+    - HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10
+    - can: af_can: fix NULL pointer dereference in can_rcv_filter
+    - clk: Fix pointer casting to prevent oops in devm_clk_release()
+    - gpiolib: improve coding style for local variables
+    - gpiolib: check the 'ngpios' property in core gpiolib code
+    - gpiolib: fix memory leak in gpiochip_setup_dev()
+    - netfilter: nft_set_pipapo: Actually validate intervals in fields after the
+      first one
+    - drm/vmwgfx: Fix race issue calling pin_user_pages
+    - ieee802154: cc2520: Fix error return code in cc2520_hw_init()
+    - ca8210: Fix crash by zero initializing data
+    - netfilter: ctnetlink: fix compilation warning after data race fixes in ct
+      mark
+    - drm/bridge: ti-sn65dsi86: Fix output polarity setting bug
+    - gpio: amd8111: Fix PCI device reference count leak
+    - e1000e: Fix TX dispatch condition
+    - igb: Allocate MSI-X vector when testing
+    - net: broadcom: Add PTP_1588_CLOCK_OPTIONAL dependency for BCMGENET under
+      ARCH_BCM2835
+    - drm: bridge: dw_hdmi: fix preference of RGB modes over YUV420
+    - af_unix: Get user_ns from in_skb in unix_diag_get_exact().
+    - vmxnet3: correctly report encapsulated LRO packet
+    - vmxnet3: use correct intrConf reference when using extended queues
+    - Bluetooth: 6LoWPAN: add missing hci_dev_put() in get_l2cap_conn()
+    - Bluetooth: Fix not cleanup led when bt_init fails
+    - net: dsa: ksz: Check return value
+    - net: dsa: hellcreek: Check return value
+    - net: dsa: sja1105: Check return value
+    - selftests: rtnetlink: correct xfrm policy rule in kci_test_ipsec_offload
+    - mac802154: fix missing INIT_LIST_HEAD in ieee802154_if_add()
+    - net: encx24j600: Add parentheses to fix precedence
+    - net: encx24j600: Fix invalid logic in reading of MISTAT register
+    - net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
+    - net: mdiobus: fix double put fwnode in the error path
+    - octeontx2-pf: Fix potential memory leak in otx2_init_tc()
+    - xen-netfront: Fix NULL sring after live migration
+    - net: mvneta: Prevent out of bounds read in mvneta_config_rss()
+    - i40e: Fix not setting default xps_cpus after reset
+    - i40e: Fix for VF MAC address 0
+    - i40e: Disallow ip4 and ip6 l4_4_bytes
+    - NFC: nci: Bounds check struct nfc_target arrays
+    - nvme initialize core quirks before calling nvme_init_subsystem
+    - gpio/rockchip: fix refcount leak in rockchip_gpiolib_register()
+    - net: stmmac: fix "snps,axi-config" node property parsing
+    - ip_gre: do not report erspan version on GRE interface
+    - net: microchip: sparx5: Fix missing destroy_workqueue of mact_queue
+    - net: thunderx: Fix missing destroy_workqueue of nicvf_rx_mode_wq
+    - net: hisilicon: Fix potential use-after-free in hisi_femac_rx()
+    - net: mdio: fix unbalanced fwnode reference count in mdio_device_release()
+    - net: hisilicon: Fix potential use-after-free in hix5hd2_rx()
+    - tipc: Fix potential OOB in tipc_link_proto_rcv()
+    - ipv4: Fix incorrect route flushing when source address is deleted
+    - ipv4: Fix incorrect route flushing when table ID 0 is used
+    - net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()
+    - tipc: call tipc_lxc_xmit without holding node_read_lock
+    - ethernet: aeroflex: fix potential skb leak in greth_init_rings()
+    - dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and
+      dpaa2_switch_acl_entry_remove()
+    - net: phy: mxl-gpy: fix version reporting
+    - net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
+    - ipv6: avoid use-after-free in ip6_fragment()
+    - net: thunderbolt: fix memory leak in tbnet_open()
+    - net: mvneta: Fix an out of bounds check
+    - macsec: add missing attribute validation for offload
+    - s390/qeth: fix various format strings
+    - s390/qeth: fix use-after-free in hsci
+    - can: esd_usb: Allow REC and TEC to return to zero
+    - block: move CONFIG_BLOCK guard to top Makefile
+    - io_uring: move to separate directory
+    - io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()
+    - Linux 5.15.83
+  * 5.15.0-58.64 breaks xen bridge networking (pvh domU) (LP: #2002889) // Jammy
+    update: v5.15.83 upstream stable release (LP: #2003134)
+    - xen/netback: fix build warning
+  * Jammy update: v5.15.82 upstream stable release (LP: #2003132)
+    - arm64: mte: Avoid setting PG_mte_tagged if no tags cleared or restored
+    - drm/i915: Create a dummy object for gen6 ppgtt
+    - drm/i915/gt: Use i915_vm_put on ppgtt_create error paths
+    - erofs: fix order >= MAX_ORDER warning due to crafted negative i_size
+    - btrfs: sink iterator parameter to btrfs_ioctl_logical_to_ino
+    - btrfs: free btrfs_path before copying inodes to userspace
+    - spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock
+    - btrfs: move QUOTA_ENABLED check to rescan_should_stop from
+      btrfs_qgroup_rescan_worker
+    - btrfs: qgroup: fix sleep from invalid context bug in btrfs_qgroup_inherit()
+    - drm/display/dp_mst: Fix drm_dp_mst_add_affected_dsc_crtcs() return code
+    - drm/amdgpu: update drm_display_info correctly when the edid is read
+    - drm/amdgpu: Partially revert "drm/amdgpu: update drm_display_info correctly
+      when the edid is read"
+    - iio: health: afe4403: Fix oob read in afe4403_read_raw
+    - iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw
+    - iio: light: rpr0521: add missing Kconfig dependencies
+    - bpf, perf: Use subprog name when reporting subprog ksymbol
+    - scripts/faddr2line: Fix regression in name resolution on ppc64le
+    - ARM: at91: rm9200: fix usb device clock id
+    - libbpf: Handle size overflow for ringbuf mmap
+    - hwmon: (ltc2947) fix temperature scaling
+    - hwmon: (ina3221) Fix shunt sum critical calculation
+    - hwmon: (i5500_temp) fix missing pci_disable_device()
+    - hwmon: (ibmpex) Fix possible UAF when ibmpex_register_bmc() fails
+    - bpf: Do not copy spin lock field from user in bpf_selem_alloc
+    - nvmem: rmem: Fix return value check in rmem_read()
+    - of: property: decrement node refcount in of_fwnode_get_reference_args()
+    - ixgbevf: Fix resource leak in ixgbevf_init_module()
+    - i40e: Fix error handling in i40e_init_module()
+    - fm10k: Fix error handling in fm10k_init_module()
+    - iavf: remove redundant ret variable
+    - iavf: Fix error handling in iavf_init_module()
+    - e100: Fix possible use after free in e100_xmit_prepare
+    - net/mlx5: DR, Fix uninitialized var warning
+    - net/mlx5: Fix uninitialized variable bug in outlen_write()
+    - net/mlx5e: Fix use-after-free when reverting termination table
+    - can: sja1000_isa: sja1000_isa_probe(): add missing free_sja1000dev()
+    - can: cc770: cc770_isa_probe(): add missing free_cc770dev()
+    - can: etas_es58x: es58x_init_netdev(): free netdev when register_candev()
+    - can: m_can: pci: add missing m_can_class_free_dev() in probe/remove methods
+    - can: m_can: Add check for devm_clk_get
+    - qlcnic: fix sleep-in-atomic-context bugs caused by msleep
+    - aquantia: Do not purge addresses when setting the number of rings
+    - wifi: cfg80211: fix buffer overflow in elem comparison
+    - wifi: cfg80211: don't allow multi-BSSID in S1G
+    - wifi: mac8021: fix possible oob access in ieee80211_get_rate_duration
+    - net: phy: fix null-ptr-deref while probe() failed
+    - net: ethernet: ti: am65-cpsw: fix error handling in am65_cpsw_nuss_probe()
+    - net: net_netdev: Fix error handling in ntb_netdev_init_module()
+    - net/9p: Fix a potential socket leak in p9_socket_open
+    - net: ethernet: nixge: fix NULL dereference
+    - net: wwan: iosm: fix kernel test robot reported error
+    - net: wwan: iosm: fix dma_alloc_coherent incompatible pointer type
+    - dsa: lan9303: Correct stat name
+    - tipc: re-fetch skb cb after tipc_msg_validate
+    - net: hsr: Fix potential use-after-free
+    - net: mdiobus: fix unbalanced node reference count
+    - afs: Fix fileserver probe RTT handling
+    - net: tun: Fix use-after-free in tun_detach()
+    - packet: do not set TP_STATUS_CSUM_VALID on CHECKSUM_COMPLETE
+    - sctp: fix memory leak in sctp_stream_outq_migrate()
+    - net: ethernet: renesas: ravb: Fix promiscuous mode after system resumed
+    - hwmon: (coretemp) Check for null before removing sysfs attrs
+    - hwmon: (coretemp) fix pci device refcount leak in nv1a_ram_new()
+    - riscv: vdso: fix section overlapping under some conditions
+    - riscv: mm: Proper page permissions after initmem free
+    - ALSA: dice: fix regression for Lexicon I-ONIX FW810S
+    - error-injection: Add prompt for function error injection
+    - tools/vm/slabinfo-gnuplot: use "grep -E" instead of "egrep"
+    - nilfs2: fix NULL pointer dereference in nilfs_palloc_commit_free_entry()
+    - x86/bugs: Make sure MSR_SPEC_CTRL is updated properly upon resume from S3
+    - pinctrl: intel: Save and restore pins in "direct IRQ" mode
+    - v4l2: don't fall back to follow_pfn() if pin_user_pages_fast() fails
+    - net: stmmac: Set MAC's flow control register to reflect current settings
+    - mmc: mmc_test: Fix removal of debugfs file
+    - mmc: core: Fix ambiguous TRIM and DISCARD arg
+    - mmc: sdhci-esdhc-imx: correct CQHCI exit halt state check
+    - mmc: sdhci-sprd: Fix no reset data and command after voltage switch
+    - mmc: sdhci: Fix voltage switch delay
+    - drm/amdgpu: temporarily disable broken Clang builds due to blown stack-frame
+    - drm/amdgpu: enable Vangogh VCN indirect sram mode
+    - drm/i915: Fix negative value passed as remaining time
+    - drm/i915: Never return 0 if not all requests retired
+    - tracing/osnoise: Fix duration type
+    - tracing: Fix race where histograms can be called before the event
+    - tracing: Free buffers when a used dynamic event is removed
+    - io_uring: update res mask in io_poll_check_events
+    - io_uring: fix tw losing poll events
+    - io_uring: cmpxchg for poll arm refs release
+    - io_uring: make poll refs more robust
+    - io_uring/poll: fix poll_refs race with cancelation
+    - KVM: x86/mmu: Fix race condition in direct_page_fault
+    - ASoC: ops: Fix bounds check for _sx controls
+    - pinctrl: single: Fix potential division by zero
+    - riscv: Sync efi page table's kernel mappings before switching
+    - riscv: fix race when vmap stack overflow
+    - riscv: kexec: Fixup irq controller broken in kexec crash path
+    - nvme: fix SRCU protection of nvme_ns_head list
+    - iommu/vt-d: Fix PCI device refcount leak in has_external_pci()
+    - iommu/vt-d: Fix PCI device refcount leak in dmar_dev_scope_init()
+    - mm: __isolate_lru_page_prepare() in isolate_migratepages_block()
+    - mm: migrate: fix THP's mapcount on isolation
+    - parisc: Increase FRAME_WARN to 2048 bytes on parisc
+    - Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is
+      enabled
+    - selftests: net: add delete nexthop route warning test
+    - selftests: net: fix nexthop warning cleanup double ip typo
+    - ipv4: Handle attempt to delete multipath route when fib_info contains an nh
+      reference
+    - ipv4: Fix route deletion when nexthop info is not specified
+    - serial: stm32: Factor out GPIO RTS toggling into separate function
+    - serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode
+    - serial: stm32: Deassert Transmit Enable on ->rs485_config()
+    - i2c: npcm7xx: Fix error handling in npcm_i2c_init()
+    - i2c: imx: Only DMA messages with I2C_M_DMA_SAFE flag set
+    - ACPI: HMAT: remove unnecessary variable initialization
+    - ACPI: HMAT: Fix initiator registration for single-initiator systems
+    - Revert "clocksource/drivers/riscv: Events are stopped during CPU suspend"
+    - char: tpm: Protect tpm_pm_suspend with locks
+    - Input: raydium_ts_i2c - fix memory leak in raydium_i2c_send()
+    - ipc/sem: Fix dangling sem_array access in semtimedop race
+    - Linux 5.15.82
+  * Jammy update: v5.15.81 upstream stable release (LP: #2003130)
+    - ASoC: fsl_sai: use local device pointer
+    - ASoC: fsl_asrc fsl_esai fsl_sai: allow CONFIG_PM=N
+    - serial: Add rs485_supported to uart_port
+    - serial: fsl_lpuart: Fill in rs485_supported
+    - tty: serial: fsl_lpuart: don't break the on-going transfer when global reset
+    - sctp: remove the unnecessary sinfo_stream check in sctp_prsctp_prune_unsent
+    - sctp: clear out_curr if all frag chunks of current msg are pruned
+    - cifs: introduce new helper for cifs_reconnect()
+    - cifs: split out dfs code from cifs_reconnect()
+    - cifs: support nested dfs links over reconnect
+    - cifs: Fix connections leak when tlink setup failed
+    - ata: libata-scsi: simplify __ata_scsi_queuecmd()
+    - ata: libata-core: do not issue non-internal commands once EH is pending
+    - drm/display: Don't assume dual mode adaptors support i2c sub-addressing
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro
+    - nvme-pci: disable namespace identifiers for the MAXIO MAP1001
+    - nvme-pci: disable write zeroes on various Kingston SSD
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000
+    - iio: ms5611: Simplify IO callback parameters
+    - iio: pressure: ms5611: fixed value compensation bug
+    - ceph: do not update snapshot context when there is no new snapshot
+    - ceph: avoid putting the realm twice when decoding snaps fails
+    - x86/sgx: Create utility to validate user provided offset and length
+    - x86/sgx: Add overflow check in sgx_validate_offset_length()
+    - binder: validate alloc->mm in ->mmap() handler
+    - ceph: Use kcalloc for allocating multiple elements
+    - ceph: fix NULL pointer dereference for req->r_session
+    - wifi: mac80211: fix memory free error when registering wiphy fail
+    - wifi: mac80211_hwsim: fix debugfs attribute ps with rc table support
+    - riscv: dts: sifive unleashed: Add PWM controlled LEDs
+    - audit: fix undefined behavior in bit shift for AUDIT_BIT
+    - wifi: airo: do not assign -1 to unsigned char
+    - wifi: mac80211: Fix ack frame idr leak when mesh has no route
+    - wifi: ath11k: Fix QCN9074 firmware boot on x86
+    - spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
+    - selftests/bpf: Add verifier test for release_reference()
+    - Revert "net: macsec: report real_dev features when HW offloading is enabled"
+    - platform/x86: ideapad-laptop: Disable touchpad_switch
+    - platform/x86: touchscreen_dmi: Add info for the RCA Cambio W101 v2 2-in-1
+    - platform/x86/intel/pmt: Sapphire Rapids PMT errata fix
+    - platform/x86/intel/hid: Add some ACPI device IDs
+    - scsi: ibmvfc: Avoid path failures during live migration
+    - scsi: scsi_debug: Make the READ CAPACITY response compliant with ZBC
+    - drm: panel-orientation-quirks: Add quirk for Acer Switch V 10 (SW5-017)
+    - block, bfq: fix null pointer dereference in bfq_bio_bfqg()
+    - arm64/syscall: Include asm/ptrace.h in syscall_wrapper header.
+    - nvmet: fix memory leak in nvmet_subsys_attr_model_store_locked
+    - Revert "drm/amdgpu: Revert "drm/amdgpu: getting fan speed pwm for vega10
+      properly""
+    - ALSA: usb-audio: add quirk to fix Hamedal C20 disconnect issue
+    - RISC-V: vdso: Do not add missing symbols to version section in linker script
+    - MIPS: pic32: treat port as signed integer
+    - xfrm: fix "disable_policy" on ipv4 early demux
+    - xfrm: replay: Fix ESN wrap around for GSO
+    - af_key: Fix send_acquire race with pfkey_register
+    - ARM: dts: am335x-pcm-953: Define fixed regulators in root node
+    - ASoC: hdac_hda: fix hda pcm buffer overflow issue
+    - ASoC: sgtl5000: Reset the CHIP_CLK_CTRL reg on remove
+    - ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()
+    - x86/hyperv: Restore VP assist page after cpu offlining/onlining
+    - scsi: storvsc: Fix handling of srb_status and capacity change events
+    - ASoC: max98373: Add checks for devm_kcalloc
+    - regulator: core: fix kobject release warning and memory leak in
+      regulator_register()
+    - spi: dw-dma: decrease reference count in dw_spi_dma_init_mfld()
+    - regulator: core: fix UAF in destroy_regulator()
+    - bus: sunxi-rsb: Remove the shutdown callback
+    - bus: sunxi-rsb: Support atomic transfers
+    - tee: optee: fix possible memory leak in optee_register_device()
+    - ARM: dts: at91: sam9g20ek: enable udc vbus gpio pinctrl
+    - selftests: mptcp: more stable simult_flows tests
+    - selftests: mptcp: fix mibit vs mbit mix up
+    - net: liquidio: simplify if expression
+    - rxrpc: Allow list of in-use local UDP endpoints to be viewed in /proc
+    - rxrpc: Use refcount_t rather than atomic_t
+    - rxrpc: Fix race between conn bundle lookup and bundle removal [ZDI-
+      CAN-15975]
+    - net: dsa: sja1105: disallow C45 transactions on the BASE-TX MDIO bus
+    - nfc/nci: fix race with opening and closing
+    - net: pch_gbe: fix potential memleak in pch_gbe_tx_queue()
+    - 9p/fd: fix issue of list_del corruption in p9_fd_cancel()
+    - netfilter: conntrack: Fix data-races around ct mark
+    - netfilter: nf_tables: do not set up extensions for end interval
+    - iavf: Fix a crash during reset task
+    - iavf: Do not restart Tx queues after reset task failure
+    - iavf: Fix race condition between iavf_shutdown and iavf_remove
+    - ARM: mxs: fix memory leak in mxs_machine_init()
+    - ARM: dts: imx6q-prti6q: Fix ref/tcxo-clock-frequency properties
+    - net: ethernet: mtk_eth_soc: fix error handling in mtk_open()
+    - net/mlx4: Check retval of mlx4_bitmap_init
+    - net: mvpp2: fix possible invalid pointer dereference
+    - net/qla3xxx: fix potential memleak in ql3xxx_send()
+    - octeontx2-af: debugsfs: fix pci device refcount leak
+    - net: pch_gbe: fix pci device refcount leak while module exiting
+    - nfp: fill splittable of devlink_port_attrs correctly
+    - nfp: add port from netdev validation for EEPROM access
+    - macsec: Fix invalid error code set
+    - Drivers: hv: vmbus: fix double free in the error path of
+      vmbus_add_channel_work()
+    - Drivers: hv: vmbus: fix possible memory leak in vmbus_device_register()
+    - netfilter: ipset: regression in ip_set_hash_ip.c
+    - net/mlx5: Do not query pci info while pci disabled
+    - net/mlx5: Fix FW tracer timestamp calculation
+    - net/mlx5: Fix handling of entry refcount when command is not issued to FW
+    - tipc: set con sock in tipc_conn_alloc
+    - tipc: add an extra conn_get in tipc_conn_alloc
+    - tipc: check skb_linearize() return value in tipc_disc_rcv()
+    - xfrm: Fix oops in __xfrm_state_delete()
+    - xfrm: Fix ignored return value in xfrm6_init()
+    - net: wwan: iosm: use ACPI_FREE() but not kfree() in ipc_pcie_read_bios_cfg()
+    - sfc: fix potential memleak in __ef100_hard_start_xmit()
+    - net: sparx5: fix error handling in sparx5_port_open()
+    - net: sched: allow act_ct to be built without NF_NAT
+    - NFC: nci: fix memory leak in nci_rx_data_packet()
+    - regulator: twl6030: re-add TWL6032_SUBCLASS
+    - bnx2x: fix pci device refcount leak in bnx2x_vf_is_pcie_pending()
+    - dma-buf: fix racing conflict of dma_heap_add()
+    - netfilter: ipset: restore allowing 64 clashing elements in hash:net,iface
+    - netfilter: flowtable_offload: add missing locking
+    - fs: do not update freeing inode i_io_list
+    - dccp/tcp: Reset saddr on failure after inet6?_hash_connect().
+    - ipv4: Fix error return code in fib_table_insert()
+    - arcnet: fix potential memory leak in com20020_probe()
+    - s390/dasd: fix no record found for raw_track_access
+    - nfc: st-nci: fix incorrect validating logic in EVT_TRANSACTION
+    - nfc: st-nci: fix memory leaks in EVT_TRANSACTION
+    - nfc: st-nci: fix incorrect sizing calculations in EVT_TRANSACTION
+    - net: enetc: manage ENETC_F_QBV in priv->active_offloads only when enabled
+    - net: enetc: cache accesses to &priv->si->hw
+    - net: enetc: preserve TX ring priority across reconfiguration
+    - octeontx2-pf: Add check for devm_kcalloc
+    - octeontx2-af: Fix reference count issue in rvu_sdp_init()
+    - net: thunderx: Fix the ACPI memory leak
+    - s390/crashdump: fix TOD programmable field size
+    - lib/vdso: use "grep -E" instead of "egrep"
+    - [Config] updateconfigs for CC_HAS_ASM_GOTO_TIED_OUTPUT
+    - init/Kconfig: fix CC_HAS_ASM_GOTO_TIED_OUTPUT test with dash
+    - nios2: add FORCE for vmlinuz.gz
+    - mmc: sdhci-brcmstb: Re-organize flags
+    - mmc: sdhci-brcmstb: Enable Clock Gating to save power
+    - mmc: sdhci-brcmstb: Fix SDHCI_RESET_ALL for CQHCI
+    - KVM: arm64: pkvm: Fixup boot mode to reflect that the kernel resumes from
+      EL1
+    - usb: dwc3: exynos: Fix remove() function
+    - usb: cdnsp: Fix issue with Clear Feature Halt Endpoint
+    - usb: cdnsp: fix issue with ZLP - added TD_SIZE = 1
+    - ext4: fix use-after-free in ext4_ext_shift_extents
+    - arm64: dts: rockchip: lower rk3399-puma-haikou SD controller clock frequency
+    - iio: light: apds9960: fix wrong register for gesture gain
+    - iio: core: Fix entry not deleted when iio_register_sw_trigger_type() fails
+    - bus: ixp4xx: Don't touch bit 7 on IXP42x
+    - usb: dwc3: gadget: conditionally remove requests
+    - usb: dwc3: gadget: Return -ESHUTDOWN on ep disable
+    - usb: dwc3: gadget: Clear ep descriptor last
+    - nilfs2: fix nilfs_sufile_mark_dirty() not set segment usage as dirty
+    - gcov: clang: fix the buffer overflow issue
+    - mm: vmscan: fix extreme overreclaim and swap floods
+    - KVM: x86: nSVM: leave nested mode on vCPU free
+    - KVM: x86: forcibly leave nested mode on vCPU reset
+    - KVM: x86: nSVM: harden svm_free_nested against freeing vmcb02 while still in
+      use
+    - KVM: x86: add kvm_leave_nested
+    - KVM: x86: remove exit_int_info warning in svm_handle_exit
+    - x86/tsx: Add a feature bit for TSX control MSR support
+    - x86/pm: Add enumeration check before spec MSRs save/restore setup
+    - x86/ioremap: Fix page aligned size calculation in __ioremap_caller()
+    - Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode
+    - ASoC: Intel: bytcht_es8316: Add quirk for the Nanote UMPC-01
+    - tools: iio: iio_generic_buffer: Fix read size
+    - serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
+    - Input: goodix - try resetting the controller when no config is set
+    - Input: soc_button_array - add use_low_level_irq module parameter
+    - Input: soc_button_array - add Acer Switch V 10 to dmi_use_low_level_irq[]
+    - Input: i8042 - apply probe defer to more ASUS ZenBook models
+    - ASoC: stm32: dfsdm: manage cb buffers cleanup
+    - xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too
+    - xen/platform-pci: add missing free_irq() in error path
+    - platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
+    - platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)
+    - drm/amdgpu: disable BACO support on more cards
+    - zonefs: fix zone report size in __zonefs_io_error()
+    - platform/x86: hp-wmi: Ignore Smart Experience App event
+    - platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some
+      Yoga laptops
+    - [Config] updateconfigs for INET_TABLE_PERTURB_ORDER
+    - tcp: configurable source port perturb table size
+    - net: usb: qmi_wwan: add Telit 0x103a composition
+    - scsi: iscsi: Fix possible memory leak when device_register() failed
+    - gpu: host1x: Avoid trying to use GART on Tegra20
+    - dm integrity: flush the journal on suspend
+    - dm integrity: clear the journal on suspend
+    - fuse: lock inode unconditionally in fuse_fallocate()
+    - wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_OPER_CHANNEL attribute
+    - wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_CHANNEL_LIST attribute
+    - wifi: wilc1000: validate number of channels
+    - genirq/msi: Shutdown managed interrupts with unsatifiable affinities
+    - genirq: Always limit the affinity to online CPUs
+    - irqchip/gic-v3: Always trust the managed affinity provided by the core code
+    - genirq: Take the proposed affinity at face value if force==true
+    - btrfs: free btrfs_path before copying root refs to userspace
+    - btrfs: free btrfs_path before copying fspath to userspace
+    - btrfs: free btrfs_path before copying subvol info to userspace
+    - btrfs: zoned: fix missing endianness conversion in sb_write_pointer
+    - btrfs: use kvcalloc in btrfs_get_dev_zone_info
+    - btrfs: sysfs: normalize the error handling branch in btrfs_init_sysfs()
+    - drm/amd/dc/dce120: Fix audio register mapping, stop triggering KASAN
+    - drm/amd/display: No display after resume from WB/CB
+    - drm/amdgpu: Enable Aldebaran devices to report CU Occupancy
+    - drm/amdgpu: always register an MMU notifier for userptr
+    - cifs: fix missed refcounting of ipc tcon
+    - Linux 5.15.81
+  * Jammy update: v5.15.80 upstream stable release (LP: #2003122)
+    - mm: hwpoison: refactor refcount check handling
+    - mm: hwpoison: handle non-anonymous THP correctly
+    - mm: shmem: don't truncate page if memory failure happens
+    - ASoC: wm5102: Revert "ASoC: wm5102: Fix PM disable depth imbalance in
+      wm5102_probe"
+    - ASoC: wm5110: Revert "ASoC: wm5110: Fix PM disable depth imbalance in
+      wm5110_probe"
+    - ASoC: wm8997: Revert "ASoC: wm8997: Fix PM disable depth imbalance in
+      wm8997_probe"
+    - ASoC: mt6660: Keep the pm_runtime enables before component stuff in
+      mt6660_i2c_probe
+    - ASoC: rt1019: Fix the TDM settings
+    - ASoC: wm8962: Add an event handler for TEMP_HP and TEMP_SPK
+    - spi: intel: Fix the offset to get the 64K erase opcode
+    - ASoC: codecs: jz4725b: add missed Line In power control bit
+    - ASoC: codecs: jz4725b: fix reported volume for Master ctl
+    - ASoC: codecs: jz4725b: use right control for Capture Volume
+    - ASoC: codecs: jz4725b: fix capture selector naming
+    - ASoC: Intel: sof_sdw: add quirk variant for LAPBC710 NUC15
+    - selftests/futex: fix build for clang
+    - selftests/intel_pstate: fix build for ARCH=x86_64
+    - ASoC: rt1308-sdw: add the default value of some registers
+    - drm/amd/display: Remove wrong pipe control lock
+    - ACPI: scan: Add LATT2021 to acpi_ignore_dep_ids[]
+    - RDMA/efa: Add EFA 0xefa2 PCI ID
+    - btrfs: raid56: properly handle the error when unable to find the missing
+      stripe
+    - NFSv4: Retry LOCK on OLD_STATEID during delegation return
+    - ACPI: x86: Add another system to quirk list for forcing StorageD3Enable
+    - firmware: arm_scmi: Cleanup the core driver removal callback
+    - i2c: tegra: Allocate DMA memory for DMA engine
+    - i2c: i801: add lis3lv02d's I2C address for Vostro 5568
+    - drm/imx: imx-tve: Fix return type of imx_tve_connector_mode_valid
+    - btrfs: remove pointless and double ulist frees in error paths of qgroup
+      tests
+    - x86/cpu: Add several Intel server CPU model numbers
+    - ASoC: codecs: jz4725b: Fix spelling mistake "Sourc" -> "Source", "Routee" ->
+      "Route"
+    - mtd: spi-nor: intel-spi: Disable write protection only if asked
+    - spi: intel: Use correct mask for flash and protected regions
+    - KVM: x86/pmu: Do not speculatively query Intel GP PMCs that don't exist yet
+    - hugetlbfs: don't delete error page from pagecache
+    - arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8150-xperia-kumano: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8250-xperia-edo: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8350-hdk: Specify which LDO modes are allowed
+    - spi: stm32: Print summary 'callbacks suppressed' message
+    - ARM: dts: at91: sama7g5: fix signal name of pin PB2
+    - ASoC: core: Fix use-after-free in snd_soc_exit()
+    - ASoC: tas2770: Fix set_tdm_slot in case of single slot
+    - ASoC: tas2764: Fix set_tdm_slot in case of single slot
+    - ARM: at91: pm: avoid soft resetting AC DLL
+    - serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl()
+    - serial: 8250_omap: remove wait loop from Errata i202 workaround
+    - serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()
+    - serial: 8250: omap: Flush PM QOS work on remove
+    - serial: imx: Add missing .thaw_noirq hook
+    - tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send
+    - bpf, test_run: Fix alignment problem in bpf_prog_test_run_skb()
+    - ASoC: soc-utils: Remove __exit for snd_soc_util_exit()
+    - pinctrl: rockchip: list all pins in a possible mux route for PX30
+    - scsi: scsi_transport_sas: Fix error handling in sas_phy_add()
+    - block: sed-opal: kmalloc the cmd/resp buffers
+    - bpf: Fix memory leaks in __check_func_call
+    - arm64: Fix bit-shifting UB in the MIDR_CPU_MODEL() macro
+    - siox: fix possible memory leak in siox_device_add()
+    - parport_pc: Avoid FIFO port location truncation
+    - pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
+    - drm/vc4: kms: Fix IS_ERR() vs NULL check for vc4_kms
+    - drm/panel: simple: set bpc field for logic technologies displays
+    - drm/drv: Fix potential memory leak in drm_dev_init()
+    - drm: Fix potential null-ptr-deref in drm_vblank_destroy_worker()
+    - arm64: dts: imx8mm: Fix NAND controller size-cells
+    - arm64: dts: imx8mn: Fix NAND controller size-cells
+    - ata: libata-transport: fix double ata_host_put() in ata_tport_add()
+    - ata: libata-transport: fix error handling in ata_tport_add()
+    - ata: libata-transport: fix error handling in ata_tlink_add()
+    - ata: libata-transport: fix error handling in ata_tdev_add()
+    - nfp: change eeprom length to max length enumerators
+    - MIPS: fix duplicate definitions for exported symbols
+    - MIPS: Loongson64: Add WARN_ON on kexec related kmalloc failed
+    - bpf: Initialize same number of free nodes for each pcpu_freelist
+    - net: bgmac: Drop free_netdev() from bgmac_enet_remove()
+    - mISDN: fix possible memory leak in mISDN_dsp_element_register()
+    - net: hinic: Fix error handling in hinic_module_init()
+    - net: stmmac: ensure tx function is not running in stmmac_xdp_release()
+    - soc: imx8m: Enable OCOTP clock before reading the register
+    - net: liquidio: release resources when liquidio driver open failed
+    - mISDN: fix misuse of put_device() in mISDN_register_device()
+    - net: macvlan: Use built-in RCU list checking
+    - net: caif: fix double disconnect client in chnl_net_open()
+    - bnxt_en: Remove debugfs when pci_register_driver failed
+    - net: mhi: Fix memory leak in mhi_net_dellink()
+    - net: dsa: make dsa_master_ioctl() see through port_hwtstamp_get() shims
+    - xen/pcpu: fix possible memory leak in register_pcpu()
+    - net: ionic: Fix error handling in ionic_init_module()
+    - net: ena: Fix error handling in ena_init()
+    - net: hns3: fix setting incorrect phy link ksettings for firmware in
+      resetting process
+    - bridge: switchdev: Fix memory leaks when changing VLAN protocol
+    - drbd: use after free in drbd_create_device()
+    - platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when
+      virtualized
+    - platform/surface: aggregator: Do not check for repeated unsequenced packets
+    - cifs: add check for returning value of SMB2_close_init
+    - net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in
+      ag71xx_open()
+    - net/x25: Fix skb leak in x25_lapb_receive_frame()
+    - cifs: Fix wrong return value checking when GETFLAGS
+    - net: microchip: sparx5: Fix potential null-ptr-deref in sparx_stats_init()
+      and sparx5_start()
+    - net: thunderbolt: Fix error handling in tbnet_init()
+    - cifs: add check for returning value of SMB2_set_info_init
+    - ftrace: Fix the possible incorrect kernel message
+    - ftrace: Optimize the allocation for mcount entries
+    - ftrace: Fix null pointer dereference in ftrace_add_mod()
+    - ring_buffer: Do not deactivate non-existant pages
+    - tracing: Fix memory leak in tracing_read_pipe()
+    - tracing/ring-buffer: Have polling block on watermark
+    - tracing: Fix memory leak in test_gen_synth_cmd() and
+      test_empty_synth_event()
+    - tracing: Fix wild-memory-access in register_synth_event()
+    - tracing: Fix race where eprobes can be called before the event
+    - tracing: kprobe: Fix potential null-ptr-deref on trace_event_file in
+      kprobe_event_gen_test_exit()
+    - tracing: kprobe: Fix potential null-ptr-deref on trace_array in
+      kprobe_event_gen_test_exit()
+    - drm/amd/display: Add HUBP surface flip interrupt handler
+    - ALSA: usb-audio: Drop snd_BUG_ON() from snd_usbmidi_output_open()
+    - ALSA: hda/realtek: fix speakers for Samsung Galaxy Book Pro
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
+    - Revert "usb: dwc3: disable USB core PHY management"
+    - slimbus: qcom-ngd: Fix build error when CONFIG_SLIM_QCOM_NGD_CTRL=y &&
+      CONFIG_QCOM_RPROC_COMMON=m
+    - slimbus: stream: correct presence rate frequencies
+    - speakup: fix a segfault caused by switching consoles
+    - USB: bcma: Make GPIO explicitly optional
+    - USB: serial: option: add Sierra Wireless EM9191
+    - USB: serial: option: remove old LARA-R6 PID
+    - USB: serial: option: add u-blox LARA-R6 00B modem
+    - USB: serial: option: add u-blox LARA-L6 modem
+    - USB: serial: option: add Fibocom FM160 0x0111 composition
+    - usb: add NO_LPM quirk for Realforce 87U Keyboard
+    - usb: chipidea: fix deadlock in ci_otg_del_timer
+    - usb: cdns3: host: fix endless superspeed hub port reset
+    - usb: typec: mux: Enter safe mode only when pins need to be reconfigured
+    - iio: adc: at91_adc: fix possible memory leak in at91_adc_allocate_trigger()
+    - iio: trigger: sysfs: fix possible memory leak in iio_sysfs_trig_init()
+    - iio: adc: mp2629: fix wrong comparison of channel
+    - iio: adc: mp2629: fix potential array out of bound access
+    - iio: pressure: ms5611: changed hardcoded SPI speed to value limited
+    - dm ioctl: fix misbehavior if list_versions races with module loading
+    - serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs
+    - serial: 8250: Flush DMA Rx on RLSI
+    - serial: 8250_lpss: Configure DMA also w/o DMA filter
+    - Input: iforce - invert valid length check when fetching device IDs
+    - maccess: Fix writing offset in case of fault in
+      strncpy_from_kernel_nofault()
+    - net: phy: marvell: add sleep time after enabling the loopback bit
+    - scsi: zfcp: Fix double free of FSF request when qdio send fails
+    - iommu/vt-d: Preset Access bit for IOVA in FL non-leaf paging entries
+    - iommu/vt-d: Set SRE bit only when hardware has SRS cap
+    - firmware: coreboot: Register bus in module init
+    - mmc: core: properly select voltage range without power cycle
+    - mmc: sdhci-pci-o2micro: fix card detect fail issue caused by CD# debounce
+      timeout
+    - mmc: sdhci-pci: Fix possible memory leak caused by missing pci_dev_put()
+    - docs: update mediator contact information in CoC doc
+    - misc/vmw_vmci: fix an infoleak in vmci_host_do_receive_datagram()
+    - perf/x86/intel/pt: Fix sampling using single range output
+    - nvme: restrict management ioctls to admin
+    - nvme: ensure subsystem reset is single threaded
+    - serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake
+    - perf: Improve missing SIGTRAP checking
+    - ring-buffer: Include dropped pages in counting dirty patches
+    - tracing: Fix warning on variable 'struct trace_array'
+    - net: use struct_group to copy ip/ipv6 header addresses
+    - scsi: target: tcm_loop: Fix possible name leak in tcm_loop_setup_hba_bus()
+    - scsi: scsi_debug: Fix possible UAF in sdebug_add_host_helper()
+    - kprobes: Skip clearing aggrprobe's post_handler in kprobe-on-ftrace case
+    - Input: i8042 - fix leaking of platform device on module removal
+    - macvlan: enforce a consistent minimal mtu
+    - tcp: cdg: allow tcp_cdg_release() to be called multiple times
+    - kcm: avoid potential race in kcm_tx_work
+    - kcm: close race conditions on sk_receive_queue
+    - 9p: trans_fd/p9_conn_cancel: drop client lock earlier
+    - gfs2: Check sb_bsize_shift after reading superblock
+    - gfs2: Switch from strlcpy to strscpy
+    - 9p/trans_fd: always use O_NONBLOCK read/write
+    - wifi: wext: use flex array destination for memcpy()
+    - mm: fs: initialize fsdata passed to write_begin/write_end interface
+    - net/9p: use a dedicated spinlock for trans_fd
+    - ntfs: fix use-after-free in ntfs_attr_find()
+    - ntfs: fix out-of-bounds read in ntfs_attr_find()
+    - ntfs: check overflow when iterating ATTR_RECORDs
+    - Linux 5.15.80
+  * CVE-2022-4139
+    - drm/i915: fix TLB invalidation for Gen12 video and compute engines
+  * Jammy update: v5.15.79 upstream stable release (LP: #2001570)
+    - fuse: fix readdir cache race
+    - drm/amdkfd: avoid recursive lock in migrations back to RAM
+    - drm/amdkfd: handle CPU fault on COW mapping
+    - drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()
+    - hwspinlock: qcom: correct MMIO max register for newer SoCs
+    - phy: stm32: fix an error code in probe
+    - wifi: cfg80211: silence a sparse RCU warning
+    - wifi: cfg80211: fix memory leak in query_regdb_file()
+    - soundwire: qcom: reinit broadcast completion
+    - soundwire: qcom: check for outanding writes before doing a read
+    - bpf, verifier: Fix memory leak in array reallocation for stack state
+    - bpf, sockmap: Fix the sk->sk_forward_alloc warning of sk_stream_kill_queues
+    - wifi: mac80211: Set TWT Information Frame Disabled bit as 1
+    - bpftool: Fix NULL pointer dereference when pin {PROG, MAP, LINK} without
+      FILE
+    - HID: hyperv: fix possible memory leak in mousevsc_probe()
+    - bpf, sockmap: Fix sk->sk_forward_alloc warn_on in sk_stream_kill_queues
+    - bpf: Fix sockmap calling sleepable function in teardown path
+    - bpf, sock_map: Move cancel_work_sync() out of sock lock
+    - bpf: Add helper macro bpf_for_each_reg_in_vstate
+    - bpf: Fix wrong reg type conversion in release_reference()
+    - net: gso: fix panic on frag_list with mixed head alloc types
+    - macsec: delete new rxsc when offload fails
+    - macsec: fix secy->n_rx_sc accounting
+    - macsec: fix detection of RXSCs when toggling offloading
+    - macsec: clear encryption keys from the stack after setting up offload
+    - octeontx2-pf: Use hardware register for CQE count
+    - octeontx2-pf: NIX TX overwrites SQ_CTX_HW_S[SQ_INT]
+    - net: tun: Fix memory leaks of napi_get_frags
+    - bnxt_en: Fix possible crash in bnxt_hwrm_set_coal()
+    - bnxt_en: fix potentially incorrect return value for ndo_rx_flow_steer
+    - net: fman: Unregister ethernet device on removal
+    - capabilities: fix undefined behavior in bit shift for CAP_TO_MASK
+    - phy: ralink: mt7621-pci: add sentinel to quirks table
+    - KVM: s390: pv: don't allow userspace to set the clock under PV
+    - net: lapbether: fix issue of dev reference count leakage in
+      lapbeth_device_event()
+    - hamradio: fix issue of dev reference count leakage in bpq_device_event()
+    - net: wwan: iosm: fix memory leak in ipc_wwan_dellink
+    - net: wwan: mhi: fix memory leak in mhi_mbim_dellink
+    - drm/vc4: Fix missing platform_unregister_drivers() call in
+      vc4_drm_register()
+    - tcp: prohibit TCP_REPAIR_OPTIONS if data was already sent
+    - ipv6: addrlabel: fix infoleak when sending struct ifaddrlblmsg to network
+    - can: af_can: fix NULL pointer dereference in can_rx_register()
+    - net: stmmac: dwmac-meson8b: fix meson8b_devm_clk_prepare_enable()
+    - net: broadcom: Fix BCMGENET Kconfig
+    - tipc: fix the msg->req tlv len check in
+      tipc_nl_compat_name_table_dump_header
+    - dmaengine: pxa_dma: use platform_get_irq_optional
+    - dmaengine: mv_xor_v2: Fix a resource leak in mv_xor_v2_remove()
+    - dmaengine: ti: k3-udma-glue: fix memory leak when register device fail
+    - net: lapbether: fix issue of invalid opcode in lapbeth_open()
+    - drivers: net: xgene: disable napi when register irq failed in
+      xgene_enet_open()
+    - perf stat: Fix printing os->prefix in CSV metrics output
+    - perf tools: Add the include/perf/ directory to .gitignore
+    - netfilter: nfnetlink: fix potential dead lock in nfnetlink_rcv_msg()
+    - netfilter: Cleanup nft_net->module_list from nf_tables_exit_net()
+    - net: marvell: prestera: fix memory leak in prestera_rxtx_switch_init()
+    - net: nixge: disable napi when enable interrupts failed in nixge_open()
+    - net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg
+    - net/mlx5: Bridge, verify LAG state when adding bond to bridge
+    - net/mlx5: Allow async trigger completion execution on single CPU systems
+    - net/mlx5e: E-Switch, Fix comparing termination table instance
+    - net: cpsw: disable napi in cpsw_ndo_open()
+    - net: cxgb3_main: disable napi when bind qsets failed in cxgb_up()
+    - stmmac: intel: Enable 2.5Gbps for Intel AlderLake-S
+    - stmmac: intel: Update PCH PTP clock rate from 200MHz to 204.8MHz
+    - mctp: Fix an error handling path in mctp_init()
+    - cxgb4vf: shut down the adapter when t4vf_update_port_info() failed in
+      cxgb4vf_open()
+    - stmmac: dwmac-loongson: fix missing pci_disable_msi() while module exiting
+    - stmmac: dwmac-loongson: fix missing pci_disable_device() in
+      loongson_dwmac_probe()
+    - stmmac: dwmac-loongson: fix missing of_node_put() while module exiting
+    - net: phy: mscc: macsec: clear encryption keys when freeing a flow
+    - net: atlantic: macsec: clear encryption keys from the stack
+    - ethernet: s2io: disable napi when start nic failed in s2io_card_up()
+    - net: mv643xx_eth: disable napi when init rxq or txq failed in
+      mv643xx_eth_open()
+    - ethernet: tundra: free irq when alloc ring failed in tsi108_open()
+    - net: macvlan: fix memory leaks of macvlan_common_newlink
+    - riscv: process: fix kernel info leakage
+    - riscv: vdso: fix build with llvm
+    - riscv: fix reserved memory setup
+    - arm64: efi: Fix handling of misaligned runtime regions and drop warning
+    - MIPS: jump_label: Fix compat branch range check
+    - mmc: cqhci: Provide helper for resetting both SDHCI and CQHCI
+    - mmc: sdhci-of-arasan: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci_am654: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci-tegra: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci-esdhc-imx: use the correct host caps for MMC_CAP_8_BIT_DATA
+    - ALSA: hda/hdmi - enable runtime pm for more AMD display audio
+    - ALSA: hda/ca0132: add quirk for EVGA Z390 DARK
+    - ALSA: hda: fix potential memleak in 'add_widget_node'
+    - ALSA: hda/realtek: Add Positivo C6300 model quirk
+    - ALSA: usb-audio: Yet more regression for for the delayed card registration
+    - ALSA: usb-audio: Add quirk entry for M-Audio Micro
+    - ALSA: usb-audio: Add DSD support for Accuphase DAC-60
+    - vmlinux.lds.h: Fix placement of '.data..decrypted' section
+    - ata: libata-scsi: fix SYNCHRONIZE CACHE (16) command failure
+    - nilfs2: fix deadlock in nilfs_count_free_blocks()
+    - nilfs2: fix use-after-free bug of ns_writer on remount
+    - drm/i915/dmabuf: fix sg_table handling in map_dma_buf
+    - drm/amdgpu: disable BACO on special BEIGE_GOBY card
+    - btrfs: fix match incorrectly in dev_args_match_device
+    - btrfs: selftests: fix wrong error check in btrfs_free_dummy_root()
+    - btrfs: zoned: initialize device's zone info for seeding
+    - mms: sdhci-esdhc-imx: Fix SDHCI_RESET_ALL for CQHCI
+    - udf: Fix a slab-out-of-bounds write bug in udf_find_entry()
+    - mm/damon/dbgfs: check if rm_contexts input is for a real context
+    - mm/memremap.c: map FS_DAX device memory as decrypted
+    - mm/shmem: use page_mapping() to detect page cache for uffd continue
+    - can: j1939: j1939_send_one(): fix missing CAN header initialization
+    - cert host tools: Stop complaining about deprecated OpenSSL functions
+    - dmaengine: at_hdmac: Fix at_lli struct definition
+    - dmaengine: at_hdmac: Don't start transactions at tx_submit level
+    - dmaengine: at_hdmac: Start transfer for cyclic channels in issue_pending
+    - dmaengine: at_hdmac: Fix premature completion of desc in issue_pending
+    - dmaengine: at_hdmac: Do not call the complete callback on
+      device_terminate_all
+    - dmaengine: at_hdmac: Protect atchan->status with the channel lock
+    - dmaengine: at_hdmac: Fix concurrency problems by removing atc_complete_all()
+    - dmaengine: at_hdmac: Fix concurrency over descriptor
+    - dmaengine: at_hdmac: Free the memset buf without holding the chan lock
+    - dmaengine: at_hdmac: Fix concurrency over the active list
+    - dmaengine: at_hdmac: Fix descriptor handling when issuing it to hardware
+    - dmaengine: at_hdmac: Fix completion of unissued descriptor in case of errors
+    - dmaengine: at_hdmac: Don't allow CPU to reorder channel enable
+    - dmaengine: at_hdmac: Fix impossible condition
+    - dmaengine: at_hdmac: Check return code of dma_async_device_register
+    - marvell: octeontx2: build error: unknown type name 'u64'
+    - drm/amdkfd: Migrate in CPU page fault use current mm
+    - net: tun: call napi_schedule_prep() to ensure we own a napi
+    - x86/cpu: Restore AMD's DE_CFG MSR after resume
+    - Linux 5.15.79
+  * CVE-2022-47520
+    - wifi: wilc1000: validate pairwise and authentication suite offsets
+  * CVE-2022-3545
+    - nfp: fix use-after-free in area_cache_get()
+
+  [ Ubuntu: 5.15.0-60.66 ]
+
+  * jammy/linux: 5.15.0-60.66 -proposed tracker (LP: #2003450)
+  * Revoke & rotate to new signing key (LP: #2002812)
+    - [Packaging] Revoke and rotate to new signing key
+
+ -- Masahiro Yamada <masahiro.yamada@canonical.com>  Tue, 25 Apr 2023 14:07:38 +0900
+
+linux-xilinx-zynqmp (5.15.0-1020.22) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous upstream changes
+    - phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Thu, 23 Feb 2023 07:05:42 +0800
+
+linux-xilinx-zynqmp (5.15.0-1019.21) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - [Config] updateconfigs for IMA_TEMPLATE
+    - [Packaging] add python3-dev as build dependency
+    - [Packaging] add python3-dev as build dependency
+
+  * Jammy update: v5.15.61 upstream stable release (LP: #1990162)
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - [Config] updateconfigs for TRACE_IRQFLAGS_NMI_SUPPORT
+
+  * Fix iosm: WWAN cannot build the connection (DW5823e) (LP: #1998115)
+    - [Config] updateconfigs for CONFIG_IOSM
+
+  * Jammy update: v5.15.75 upstream stable release (LP: #1996825)
+    - [Config] updateconfigs for ARM64_ERRATUM_2441007
+    - [Config] updateconfigs for AS_HAS_NON_CONST_LEB128
+    - [Config] updateconfigs for MDIO_BITBANG
+
+  * Jammy update: v5.15.49 upstream stable release (LP: #1983149)
+    - [Config] updateconfigs for LIB_MEMNEQ
+
+  * Jammy update: v5.15.68 upstream stable release (LP: #1993003)
+    - [Config] updateconfigs for ARM64_BTI_KERNEL
+    - [Config] updateconfigs for ARM64_ERRATUM_2457168
+
+  * Jammy update: v5.15.65 upstream stable release (LP: #1991831)
+    - [Config] updateconfigs for ARM64_ERRATUM_2441009
+
+  * Jammy update: v5.15.76 upstream stable release (LP: #1997113)
+    - [Config] updateconfigs for ARM64_ERRATUM_1742098
+
+  * Create uc22 kernel snap
+    - Add uc22 kernel snap
+
+  * [vck190] IOMMU attach device failed message found in kernel log
+    - [Config] Disable ARM_SMMU and ARM_SMMU_V3
+
+  [ Ubuntu: 5.15.0-59.65 ]
+
+  * jammy/linux: 5.15.0-59.65 -proposed tracker (LP: #2001801)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+  * CVE-2022-47940
+    - ksmbd: validate length in smb2_write()
+  * Fix iosm: WWAN cannot build the connection (DW5823e) (LP: #1998115)
+    - net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled
+    - [Config] CONFIG_IOSM update annotations on arm64 armhf ppc64el s390x
+  * support for same series backports versioning numbers (LP: #1993563)
+    - [Packaging] sameport -- add support for sameport versioning
+  * [DEP-8] Run ADT regression suite for lowlatency kernels Jammy and later
+    (LP: #1999528)
+    - [DEP-8] Fix regression suite to run on lowlatency
+  * Micron NVME storage failure [1344,5407] (LP: #1998883)
+    - nvme: add a bogus subsystem NQN quirk for Micron MTFDKBA2T0TFH
+  * Jammy update: v5.15.78 upstream stable release (LP: #1998843)
+    - scsi: lpfc: Rework MIB Rx Monitor debug info logic
+    - serial: ar933x: Deassert Transmit Enable on ->rs485_config()
+    - KVM: x86: Trace re-injected exceptions
+    - KVM: x86: Treat #DBs from the emulator as fault-like (code and DR7.GD=1)
+    - drm/amd/display: explicitly disable psr_feature_enable appropriately
+    - mm/hugetlb: fix races when looking up a CONT-PTE/PMD size hugetlb page
+    - HID: playstation: add initial DualSense Edge controller support
+    - KVM: x86: Protect the unused bits in MSR exiting flags
+    - KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
+    - KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
+    - RDMA/cma: Use output interface for net_dev check
+    - IB/hfi1: Correctly move list in sc_disable()
+    - RDMA/hns: Remove magic number
+    - RDMA/hns: Use hr_reg_xxx() instead of remaining roce_set_xxx()
+    - RDMA/hns: Disable local invalidate operation
+    - NFSv4: Fix a potential state reclaim deadlock
+    - NFSv4.1: Handle RECLAIM_COMPLETE trunking errors
+    - NFSv4.1: We must always send RECLAIM_COMPLETE after a reboot
+    - SUNRPC: Fix null-ptr-deref when xps sysfs alloc failed
+    - NFSv4.2: Fixup CLONE dest file size for zero-length count
+    - nfs4: Fix kmemleak when allocate slot failed
+    - net: dsa: Fix possible memory leaks in dsa_loop_init()
+    - RDMA/core: Fix null-ptr-deref in ib_core_cleanup()
+    - RDMA/qedr: clean up work queue on failure in qedr_alloc_resources()
+    - net: dsa: fall back to default tagger if we can't load the one from DT
+    - nfc: fdp: Fix potential memory leak in fdp_nci_send()
+    - nfc: nxp-nci: Fix potential memory leak in nxp_nci_send()
+    - nfc: s3fwrn5: Fix potential memory leak in s3fwrn5_nci_send()
+    - nfc: nfcmrvl: Fix potential memory leak in nfcmrvl_i2c_nci_send()
+    - net: fec: fix improper use of NETDEV_TX_BUSY
+    - ata: pata_legacy: fix pdc20230_set_piomode()
+    - net: sched: Fix use after free in red_enqueue()
+    - net: tun: fix bugs for oversize packet when napi frags enabled
+    - netfilter: nf_tables: netlink notifier might race to release objects
+    - netfilter: nf_tables: release flow rule object from commit path
+    - ipvs: use explicitly signed chars
+    - ipvs: fix WARNING in __ip_vs_cleanup_batch()
+    - ipvs: fix WARNING in ip_vs_app_net_cleanup()
+    - rose: Fix NULL pointer dereference in rose_send_frame()
+    - mISDN: fix possible memory leak in mISDN_register_device()
+    - isdn: mISDN: netjet: fix wrong check of device registration
+    - btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
+    - btrfs: fix inode list leak during backref walking at find_parent_nodes()
+    - btrfs: fix ulist leaks in error paths of qgroup self tests
+    - netfilter: ipset: enforce documented limit to prevent allocating huge memory
+    - Bluetooth: virtio_bt: Use skb_put to set length
+    - Bluetooth: L2CAP: fix use-after-free in l2cap_conn_del()
+    - Bluetooth: L2CAP: Fix memory leak in vhci_write
+    - net: mdio: fix undefined behavior in bit shift for __mdiobus_register
+    - ibmvnic: Free rwi on reset success
+    - stmmac: dwmac-loongson: fix invalid mdio_node
+    - net/smc: Fix possible leaked pernet namespace in smc_init()
+    - net, neigh: Fix null-ptr-deref in neigh_table_clear()
+    - ipv6: fix WARNING in ip6_route_net_exit_late()
+    - vsock: fix possible infinite sleep in vsock_connectible_wait_data()
+    - drm/msm/hdmi: Remove spurious IRQF_ONESHOT flag
+    - drm/msm/hdmi: fix IRQ lifetime
+    - video/fbdev/stifb: Implement the stifb_fillrect() function
+    - fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
+    - mtd: parsers: bcm47xxpart: print correct offset on read error
+    - mtd: parsers: bcm47xxpart: Fix halfblock reads
+    - s390/uaccess: add missing EX_TABLE entries to __clear_user()
+    - s390/cio: fix out-of-bounds access on cio_ignore free
+    - media: rkisp1: Don't pass the quantization to rkisp1_csm_config()
+    - media: rkisp1: Initialize color space on resizer sink and source pads
+    - media: rkisp1: Use correct macro for gradient registers
+    - media: rkisp1: Zero v4l2_subdev_format fields in when validating links
+    - media: s5p_cec: limit msg.len to CEC_MAX_MSG_SIZE
+    - media: cros-ec-cec: limit msg.len to CEC_MAX_MSG_SIZE
+    - media: dvb-frontends/drxk: initialize err to 0
+    - media: meson: vdec: fix possible refcount leak in vdec_probe()
+    - media: v4l: subdev: Fail graciously when getting try data for NULL state
+    - ACPI: APEI: Fix integer overflow in ghes_estatus_pool_init()
+    - scsi: core: Restrict legal sdev_state transitions via sysfs
+    - HID: saitek: add madcatz variant of MMO7 mouse device ID
+    - drm/amdgpu: set vm_update_mode=0 as default for Sienna Cichlid in SRIOV case
+    - i2c: xiic: Add platform module alias
+    - efi/tpm: Pass correct address to memblock_reserve
+    - clk: qcom: Update the force mem core bit for GPU clocks
+    - ARM: dts: imx6qdl-gw59{10,13}: fix user pushbutton GPIO offset
+    - arm64: dts: imx8: correct clock order
+    - arm64: dts: lx2160a: specify clock frequencies for the MDIO controllers
+    - arm64: dts: ls1088a: specify clock frequencies for the MDIO controllers
+    - arm64: dts: ls208xa: specify clock frequencies for the MDIO controllers
+    - block: Fix possible memory leak for rq_wb on add_disk failure
+    - firmware: arm_scmi: Suppress the driver's bind attributes
+    - firmware: arm_scmi: Make Rx chan_setup fail on memory errors
+    - firmware: arm_scmi: Fix devres allocation device in virtio transport
+    - arm64: dts: juno: Add thermal critical trip points
+    - i2c: piix4: Fix adapter not be removed in piix4_remove()
+    - Bluetooth: L2CAP: Fix attempting to access uninitialized memory
+    - block, bfq: protect 'bfqd->queued' by 'bfqd->lock'
+    - af_unix: Fix memory leaks of the whole sk due to OOB skb.
+    - fscrypt: stop using keyrings subsystem for fscrypt_master_key
+    - fscrypt: fix keyring memory leak on mount failure
+    - btrfs: fix lost file sync on direct IO write with nowait and dsync iocb
+    - btrfs: fix tree mod log mishandling of reallocated nodes
+    - btrfs: fix type of parameter generation in btrfs_get_dentry
+    - ftrace: Fix use-after-free for dynamic ftrace_ops
+    - tcp/udp: Make early_demux back namespacified.
+    - tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
+    - kprobe: reverse kp->flags when arm_kprobe failed
+    - ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()
+    - tools/nolibc/string: Fix memcmp() implementation
+    - tracing/histogram: Update document for KEYS_MAX size
+    - capabilities: fix potential memleak on error path from vfs_getxattr_alloc()
+    - fuse: add file_modified() to fallocate
+    - efi: random: reduce seed size to 32 bytes
+    - efi: random: Use 'ACPI reclaim' memory for random seed
+    - arm64: entry: avoid kprobe recursion
+    - perf/x86/intel: Fix pebs event constraints for ICL
+    - perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
+    - perf/x86/intel: Fix pebs event constraints for SPR
+    - parisc: Make 8250_gsc driver dependend on CONFIG_PARISC
+    - parisc: Export iosapic_serial_irq() symbol for serial port driver
+    - parisc: Avoid printing the hardware path twice
+    - ext4: fix warning in 'ext4_da_release_space'
+    - ext4: fix BUG_ON() when directory entry has invalid rec_len
+    - x86/syscall: Include asm/ptrace.h in syscall_wrapper header
+    - KVM: x86: Mask off reserved bits in CPUID.80000006H
+    - KVM: x86: Mask off reserved bits in CPUID.8000001AH
+    - KVM: x86: Mask off reserved bits in CPUID.80000008H
+    - KVM: x86: Mask off reserved bits in CPUID.80000001H
+    - KVM: x86: Mask off reserved bits in CPUID.8000001FH
+    - KVM: VMX: fully disable SGX if SECONDARY_EXEC_ENCLS_EXITING unavailable
+    - KVM: arm64: Fix bad dereference on MTE-enabled systems
+    - KVM: x86: emulator: em_sysexit should update ctxt->mode
+    - KVM: x86: emulator: introduce emulator_recalc_and_set_mode
+    - KVM: x86: emulator: update the emulation mode after rsm
+    - KVM: x86: emulator: update the emulation mode after CR0 write
+    - tee: Fix tee_shm_register() for kernel TEE drivers
+    - ext4,f2fs: fix readahead of verity data
+    - cifs: fix regression in very old smb1 mounts
+    - drm/rockchip: dsi: Clean up 'usage_mode' when failing to attach
+    - drm/rockchip: dsi: Force synchronous probe
+    - drm/i915/sdvo: Filter out invalid outputs more sensibly
+    - drm/i915/sdvo: Setup DDC fully before output init
+    - wifi: brcmfmac: Fix potential buffer overflow in brcmf_fweh_event_worker()
+    - Linux 5.15.78
+  * Fix AMD-PState driver for Genoa CPU (LP: #1998106)
+    - Documentation: amd-pstate: add tracer tool introduction
+    - Documentation: amd-pstate: grammar and sentence structure updates
+    - Documentation: amd-pstate: Add unit test introduction
+    - cpufreq: amd-pstate: cpufreq: amd-pstate: reset MSR_AMD_PERF_CTL register at
+      init
+    - cpufreq: amd-pstate: change amd-pstate driver to be built-in type
+    - cpufreq: amd-pstate: add amd-pstate driver parameter for mode selection
+    - Documentation: amd-pstate: add driver working mode introduction
+    - Documentation: add amd-pstate kernel command line options
+  * Mediatek WLAN RZ616(MT7922) SAR table control (LP: #1997200)
+    - mt76: mt7921: add .set_sar_specs support
+    - mt76: add 6 GHz band support in mt76_sar_freq_ranges
+    - mt76: mt7921: introduce ACPI SAR support
+    - mt76: connac: add support for limiting to maximum regulatory Tx power
+    - mt76: move sar utilities to mt76-core module
+    - mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in
+      mt7921_config
+    - mt76: mt7921: introduce ACPI SAR config in tx power
+    - wifi: mt76: mt7921: fix use after free in mt7921_acpi_read()
+  * [22.04/Jammy] Replace SAUCE AMD DP tunneling patch by upstream version
+    (LP: #1989944)
+    - Revert "UBUNTU: SAUCE: thunderbolt: Add DP out resource when DP tunnel is
+      discovered."
+    - thunderbolt: Add DP OUT resource when DP tunnel is discovered
+  * Jammy update: v5.15.77 upstream stable release (LP: #1997981)
+    - NFSv4: Fix free of uninitialized nfs4_label on referral lookup.
+    - NFSv4: Add an fattr allocation to _nfs4_discover_trunking()
+    - can: j1939: transport: j1939_session_skb_drop_old():
+      spin_unlock_irqrestore() before kfree_skb()
+    - can: kvaser_usb: Fix possible completions during init_completion
+    - ALSA: Use del_timer_sync() before freeing timer
+    - ALSA: usb-audio: Add quirks for M-Audio Fast Track C400/600
+    - ALSA: au88x0: use explicitly signed char
+    - ALSA: rme9652: use explicitly signed char
+    - USB: add RESET_RESUME quirk for NVIDIA Jetson devices in RCM
+    - usb: gadget: uvc: fix sg handling in error case
+    - usb: gadget: uvc: fix sg handling during video encode
+    - usb: dwc3: gadget: Stop processing more requests on IMI
+    - usb: dwc3: gadget: Don't set IMI for no_interrupt
+    - usb: bdc: change state when port disconnected
+    - usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96
+      controller
+    - mtd: rawnand: marvell: Use correct logic for nand-keep-config
+    - xhci: Add quirk to reset host back to default state at shutdown
+    - xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
+    - xhci: Remove device endpoints from bandwidth list when freeing the device
+    - tools: iio: iio_utils: fix digit calculation
+    - iio: light: tsl2583: Fix module unloading
+    - iio: temperature: ltc2983: allocate iio channels once
+    - iio: adxl372: Fix unsafe buffer attributes
+    - fbdev: smscufx: Fix several use-after-free bugs
+    - cpufreq: intel_pstate: Read all MSRs on the target CPU
+    - cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores
+    - fs/binfmt_elf: Fix memory leak in load_elf_binary()
+    - exec: Copy oldsighand->action under spin-lock
+    - mac802154: Fix LQI recording
+    - scsi: qla2xxx: Use transport-defined speed mask for supported_speeds
+    - drm/amdgpu: disallow gfxoff until GC IP blocks complete s2idle resume
+    - drm/msm/dsi: fix memory corruption with too many bridges
+    - drm/msm/hdmi: fix memory corruption with too many bridges
+    - drm/msm/dp: fix IRQ lifetime
+    - coresight: cti: Fix hang in cti_disable_hw()
+    - mmc: sdhci_am654: 'select', not 'depends' REGMAP_MMIO
+    - mmc: core: Fix kernel panic when remove non-standard SDIO card
+    - mmc: sdhci-pci-core: Disable ES for ASUS BIOS on Jasper Lake
+    - mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus
+    - counter: microchip-tcb-capture: Handle Signal1 read and Synapse
+    - kernfs: fix use-after-free in __kernfs_remove
+    - pinctrl: Ingenic: JZ4755 bug fixes
+    - ARC: mm: fix leakage of memory allocated for PTE
+    - perf auxtrace: Fix address filter symbol name match for modules
+    - s390/futex: add missing EX_TABLE entry to __futex_atomic_op()
+    - s390/pci: add missing EX_TABLE entries to
+      __pcistg_mio_inuser()/__pcilg_mio_inuser()
+    - Revert "scsi: lpfc: Resolve some cleanup issues following SLI path
+      refactoring"
+    - Revert "scsi: lpfc: Fix element offset in __lpfc_sli_release_iocbq_s4()"
+    - Revert "scsi: lpfc: Fix locking for lpfc_sli_iocbq_lookup()"
+    - Revert "scsi: lpfc: SLI path split: Refactor SCSI paths"
+    - Revert "scsi: lpfc: SLI path split: Refactor fast and slow paths to native
+      SLI4"
+    - Revert "scsi: lpfc: SLI path split: Refactor lpfc_iocbq"
+    - mmc: block: Remove error check of hw_reset on reset
+    - ethtool: eeprom: fix null-deref on genl_info in dump
+    - net: ieee802154: fix error return code in dgram_bind()
+    - media: v4l2: Fix v4l2_i2c_subdev_set_name function documentation
+    - media: atomisp: prevent integer overflow in sh_css_set_black_frame()
+    - drm/msm: Fix return type of mdp4_lvds_connector_mode_valid
+    - KVM: selftests: Fix number of pages for memory slot in
+      memslot_modification_stress_test
+    - ASoC: qcom: lpass-cpu: mark HDMI TX registers as volatile
+    - perf: Fix missing SIGTRAPs
+    - sched/core: Fix comparison in sched_group_cookie_match()
+    - arc: iounmap() arg is volatile
+    - mtd: rawnand: intel: Add missing of_node_put() in ebu_nand_probe()
+    - ASoC: qcom: lpass-cpu: Mark HDMI TX parity register as volatile
+    - ALSA: ac97: fix possible memory leak in snd_ac97_dev_register()
+    - perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
+    - tipc: fix a null-ptr-deref in tipc_topsrv_accept
+    - net: netsec: fix error handling in netsec_register_mdio()
+    - net: hinic: fix incorrect assignment issue in hinic_set_interrupt_cfg()
+    - net: hinic: fix memory leak when reading function table
+    - net: hinic: fix the issue of CMDQ memory leaks
+    - net: hinic: fix the issue of double release MBOX callback of VF
+    - net: macb: Specify PHY PM management done by MAC
+    - nfc: virtual_ncidev: Fix memory leak in virtual_nci_send()
+    - x86/unwind/orc: Fix unreliable stack dump with gcov
+    - amd-xgbe: fix the SFP compliance codes check for DAC cables
+    - amd-xgbe: add the bit rate quirk for Molex cables
+    - drm/i915/dp: Reset frl trained flag before restarting FRL training
+    - atlantic: fix deadlock at aq_nic_stop
+    - kcm: annotate data-races around kcm->rx_psock
+    - kcm: annotate data-races around kcm->rx_wait
+    - net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
+    - net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY
+    - tcp: minor optimization in tcp_add_backlog()
+    - tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
+    - tcp: fix indefinite deferral of RTO with SACK reneging
+    - net-memcg: avoid stalls when under memory pressure
+    - drm/amdkfd: Fix memory leak in kfd_mem_dmamap_userptr()
+    - can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error
+      path
+    - can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error
+      path
+    - PM: hibernate: Allow hybrid sleep to work with s2idle
+    - media: vivid: s_fbuf: add more sanity checks
+    - media: vivid: dev->bitmap_cap wasn't freed in all cases
+    - media: v4l2-dv-timings: add sanity checks for blanking values
+    - media: videodev2.h: V4L2_DV_BT_BLANKING_HEIGHT should check 'interlaced'
+    - media: vivid: set num_in/outputs to 0 if not supported
+    - perf vendor events power10: Fix hv-24x7 metric events
+    - ipv6: ensure sane device mtu in tunnels
+    - i40e: Fix ethtool rx-flow-hash setting for X722
+    - i40e: Fix VF hang when reset is triggered on another VF
+    - i40e: Fix flow-type by setting GL_HASH_INSET registers
+    - net: ksz884x: fix missing pci_disable_device() on error in pcidev_init()
+    - PM: domains: Fix handling of unavailable/disabled idle states
+    - perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
+    - net: fec: limit register access on i.MX6UL
+    - net: ethernet: ave: Fix MAC to be in charge of PHY PM
+    - ALSA: aoa: i2sbus: fix possible memory leak in i2sbus_add_dev()
+    - ALSA: aoa: Fix I2S device accounting
+    - openvswitch: switch from WARN to pr_warn
+    - net: ehea: fix possible memory leak in ehea_register_port()
+    - net: bcmsysport: Indicate MAC is in charge of PHY PM
+    - nh: fix scope used to find saddr when adding non gw nh
+    - net: broadcom: bcm4908enet: remove redundant variable bytes
+    - net: broadcom: bcm4908_enet: update TX stats after actual transmission
+    - netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir
+      failed
+    - net/mlx5e: Do not increment ESN when updating IPsec ESN state
+    - net/mlx5e: Extend SKB room check to include PTP-SQ
+    - net/mlx5: Fix possible use-after-free in async command interface
+    - net/mlx5: Print more info on pci error handlers
+    - net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
+    - net/mlx5: Fix crash during sync firmware reset
+    - net: do not sense pfmemalloc status in skb_append_pagefrags()
+    - kcm: do not sense pfmemalloc status in kcm_sendpage()
+    - net: enetc: survive memory pressure without crashing
+    - arm64: Add AMPERE1 to the Spectre-BHB affected list
+    - scsi: sd: Revert "scsi: sd: Remove a local variable"
+    - can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
+    - can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global
+      FIFO receive
+    - serial: core: move RS485 configuration tasks from drivers into core
+    - serial: Deassert Transmit Enable on probe in driver-specific way
+    - Linux 5.15.77
+  * RCU stalls (LP: #1991951)
+    - [Config] Harmonize RCU_CPU_STALL_TIMEOUT
+  * Jammy update: v5.15.76 upstream stable release (LP: #1997113)
+    - r8152: add PID for the Lenovo OneLink+ Dock
+    - arm64/mm: Consolidate TCR_EL1 fields
+    - usb: gadget: uvc: consistently use define for headerlen
+    - usb: gadget: uvc: use on returned header len in video_encode_isoc_sg
+    - usb: gadget: uvc: rework uvcg_queue_next_buffer to uvcg_complete_buffer
+    - usb: gadget: uvc: giveback vb2 buffer on req complete
+    - usb: gadget: uvc: improve sg exit condition
+    - [Config] updateconfigs for ARM64_ERRATUM_1742098
+    - arm64: errata: Remove AES hwcap for COMPAT tasks
+    - perf/x86/intel/pt: Relax address filter validation
+    - btrfs: enhance unsupported compat RO flags handling
+    - ocfs2: clear dinode links count in case of error
+    - ocfs2: fix BUG when iput after ocfs2_mknod fails
+    - selinux: enable use of both GFP_KERNEL and GFP_ATOMIC in convert_context()
+    - cpufreq: qcom: fix writes in read-only memory region
+    - i2c: qcom-cci: Fix ordering of pm_runtime_xx and i2c_add_adapter
+    - x86/microcode/AMD: Apply the patch early on every logical thread
+    - hwmon/coretemp: Handle large core ID value
+    - ata: ahci-imx: Fix MODULE_ALIAS
+    - x86/resctrl: Fix min_cbm_bits for AMD
+    - cpufreq: qcom: fix memory leak in error path
+    - drm/amdgpu: fix sdma doorbell init ordering on APUs
+    - mm,hugetlb: take hugetlb_lock before decrementing h->resv_huge_pages
+    - kvm: Add support for arch compat vm ioctls
+    - KVM: arm64: vgic: Fix exit condition in scan_its_table()
+    - media: ipu3-imgu: Fix NULL pointer dereference in active selection access
+    - media: mceusb: set timeout to at least timeout provided
+    - media: venus: dec: Handle the case where find_format fails
+    - x86/topology: Fix multiple packages shown on a single-package system
+    - x86/topology: Fix duplicated core ID within a package
+    - btrfs: fix processing of delayed data refs during backref walking
+    - btrfs: fix processing of delayed tree block refs during backref walking
+    - drm/vc4: Add module dependency on hdmi-codec
+    - ACPI: extlog: Handle multiple records
+    - tipc: Fix recognition of trial period
+    - tipc: fix an information leak in tipc_topsrv_kern_subscr
+    - i40e: Fix DMA mappings leak
+    - HID: magicmouse: Do not set BTN_MOUSE on double report
+    - sfc: Change VF mac via PF as first preference if available.
+    - net/atm: fix proc_mpc_write incorrect return value
+    - net: phy: dp83867: Extend RX strap quirk for SGMII mode
+    - net: phylink: add mac_managed_pm in phylink_config structure
+    - scsi: lpfc: Fix memory leak in lpfc_create_port()
+    - udp: Update reuse->has_conns under reuseport_lock.
+    - cifs: Fix xid leak in cifs_create()
+    - cifs: Fix xid leak in cifs_copy_file_range()
+    - cifs: Fix xid leak in cifs_flock()
+    - cifs: Fix xid leak in cifs_ses_add_channel()
+    - dm: remove unnecessary assignment statement in alloc_dev()
+    - net: hsr: avoid possible NULL deref in skb_clone()
+    - ionic: catch NULL pointer issue on reconfig
+    - netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
+    - nvme-hwmon: consistently ignore errors from nvme_hwmon_init
+    - nvme-hwmon: kmalloc the NVME SMART log buffer
+    - nvmet: fix workqueue MEM_RECLAIM flushing dependency
+    - net: sched: cake: fix null pointer access issue when cake_init() fails
+    - net: sched: delete duplicate cleanup of backlog and qlen
+    - net: sched: sfb: fix null pointer access issue when sfb_init() fails
+    - sfc: include vport_id in filter spec hash and equal()
+    - wwan_hwsim: fix possible memory leak in wwan_hwsim_dev_new()
+    - net: hns: fix possible memory leak in hnae_ae_register()
+    - net: sched: fix race condition in qdisc_graft()
+    - net: phy: dp83822: disable MDI crossover status change interrupt
+    - iommu/vt-d: Allow NVS regions in arch_rmrr_sanity_check()
+    - iommu/vt-d: Clean up si_domain in the init_dmars() error path
+    - fs: dlm: fix invalid derefence of sb_lvbptr
+    - arm64: mte: move register initialization to C
+    - ksmbd: handle smb2 query dir request for OutputBufferLength that is too
+      small
+    - ksmbd: fix incorrect handling of iterate_dir
+    - tracing: Simplify conditional compilation code in tracing_set_tracer()
+    - tracing: Do not free snapshot if tracer is on cmdline
+    - mmc: sdhci-tegra: Use actual clock rate for SW tuning correction
+    - perf: Skip and warn on unknown format 'configN' attrs
+    - ACPI: video: Force backlight native for more TongFang devices
+    - x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
+    - Makefile.debug: re-enable debug info for .S files
+    - mmc: core: Add SD card quirk for broken discard
+    - mm: /proc/pid/smaps_rollup: fix no vma's null-deref
+    - Linux 5.15.76
+  * UBSAN: array-index-out-of-bounds in
+    /build/linux-9H675w/linux-5.15.0/drivers/ata/libahci.c:968:41
+    (LP: #1970074) // Jammy update: v5.15.76 upstream stable release
+    (LP: #1997113)
+    - ata: ahci: Match EM_MAX_SLOTS with SATA_PMP_MAX_PORTS
+  * Jammy update: v5.15.75 upstream stable release (LP: #1996825)
+    - Revert "fs: check FMODE_LSEEK to control internal pipe splicing"
+    - ALSA: oss: Fix potential deadlock at unregistration
+    - ALSA: rawmidi: Drop register_mutex in snd_rawmidi_free()
+    - ALSA: usb-audio: Fix potential memory leaks
+    - ALSA: usb-audio: Fix NULL dererence at error path
+    - ALSA: hda/realtek: remove ALC289_FIXUP_DUAL_SPK for Dell 5530
+    - ALSA: hda/realtek: Correct pin configs for ASUS G533Z
+    - ALSA: hda/realtek: Add quirk for ASUS GV601R laptop
+    - ALSA: hda/realtek: Add Intel Reference SSID to support headset keys
+    - mtd: rawnand: atmel: Unmap streaming DMA mappings
+    - io_uring/net: don't update msg_name if not provided
+    - hv_netvsc: Fix race between VF offering and VF association message from host
+    - cifs: destage dirty pages before re-reading them for cache=none
+    - cifs: Fix the error length of VALIDATE_NEGOTIATE_INFO message
+    - iio: dac: ad5593r: Fix i2c read protocol requirements
+    - iio: ltc2497: Fix reading conversion results
+    - iio: adc: ad7923: fix channel readings for some variants
+    - iio: pressure: dps310: Refactor startup procedure
+    - iio: pressure: dps310: Reset chip after timeout
+    - xhci: dbc: Fix memory leak in xhci_alloc_dbc()
+    - usb: add quirks for Lenovo OneLink+ Dock
+    - can: kvaser_usb: Fix use of uninitialized completion
+    - can: kvaser_usb_leaf: Fix overread with an invalid command
+    - can: kvaser_usb_leaf: Fix TX queue out of sync after restart
+    - can: kvaser_usb_leaf: Fix CAN state after restart
+    - mmc: sdhci-sprd: Fix minimum clock limit
+    - i2c: designware: Fix handling of real but unexpected device interrupts
+    - fs: dlm: fix race between test_bit() and queue_work()
+    - fs: dlm: handle -EBUSY first in lock arg validation
+    - HID: multitouch: Add memory barriers
+    - quota: Check next/prev free block number after reading from quota file
+    - platform/chrome: cros_ec_proto: Update version on GET_NEXT_EVENT failure
+    - ASoC: wcd9335: fix order of Slimbus unprepare/disable
+    - ASoC: wcd934x: fix order of Slimbus unprepare/disable
+    - hwmon: (gsc-hwmon) Call of_node_get() before of_find_xxx API
+    - net: thunderbolt: Enable DMA paths only after rings are enabled
+    - regulator: qcom_rpm: Fix circular deferral regression
+    - arm64: topology: move store_cpu_topology() to shared code
+    - riscv: topology: fix default topology reporting
+    - RISC-V: Make port I/O string accessors actually work
+    - parisc: fbdev/stifb: Align graphics memory size to 4MB
+    - riscv: Make VM_WRITE imply VM_READ
+    - riscv: always honor the CONFIG_CMDLINE_FORCE when parsing dtb
+    - riscv: Pass -mno-relax only on lld < 15.0.0
+    - UM: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+    - nvmem: core: Fix memleak in nvmem_register()
+    - nvme-multipath: fix possible hang in live ns resize with ANA access
+    - nvme-pci: set min_align_mask before calculating max_hw_sectors
+    - dmaengine: mxs: use platform_driver_register
+    - drm/virtio: Check whether transferred 2D BO is shmem
+    - drm/virtio: Unlock reservations on virtio_gpu_object_shmem_init() error
+    - drm/virtio: Use appropriate atomic state in virtio_gpu_plane_cleanup_fb()
+    - drm/udl: Restore display mode on resume
+    - [Config] updateconfigs for ARM64_ERRATUM_2441007
+    - arm64: errata: Add Cortex-A55 to the repeat tlbi list
+    - mm/damon: validate if the pmd entry is present before accessing
+    - mm/mmap: undo ->mmap() when arch_validate_flags() fails
+    - xen/gntdev: Prevent leaking grants
+    - xen/gntdev: Accommodate VMA splitting
+    - PCI: Sanitise firmware BAR assignments behind a PCI-PCI bridge
+    - serial: 8250: Let drivers request full 16550A feature probing
+    - serial: 8250: Request full 16550A feature probing for OxSemi PCIe devices
+    - powercap: intel_rapl: Use standard Energy Unit for SPR Dram RAPL domain
+    - powerpc/boot: Explicitly disable usage of SPE instructions
+    - slimbus: qcom-ngd: use correct error in message of pdr_add_lookup() failure
+    - slimbus: qcom-ngd: cleanup in probe error path
+    - scsi: qedf: Populate sysfs attributes for vport
+    - gpio: rockchip: request GPIO mux to pinctrl when setting direction
+    - pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
+    - fbdev: smscufx: Fix use-after-free in ufx_ops_open()
+    - ksmbd: fix endless loop when encryption for response fails
+    - ksmbd: Fix wrong return value and message length check in smb2_ioctl()
+    - ksmbd: Fix user namespace mapping
+    - fs: record I_DIRTY_TIME even if inode already has I_DIRTY_INODE
+    - btrfs: fix race between quota enable and quota rescan ioctl
+    - btrfs: set generation before calling btrfs_clean_tree_block in
+      btrfs_init_new_buffer
+    - f2fs: complete checkpoints during remount
+    - f2fs: flush pending checkpoints when freezing super
+    - f2fs: increase the limit for reserve_root
+    - f2fs: fix to do sanity check on destination blkaddr during recovery
+    - f2fs: fix to do sanity check on summary info
+    - hardening: Avoid harmless Clang option under CONFIG_INIT_STACK_ALL_ZERO
+    - hardening: Remove Clang's enable flag for -ftrivial-auto-var-init=zero
+    - jbd2: wake up journal waiters in FIFO order, not LIFO
+    - jbd2: fix potential buffer head reference count leak
+    - jbd2: fix potential use-after-free in jbd2_fc_wait_bufs
+    - jbd2: add miss release buffer head in fc_do_one_pass()
+    - ext4: avoid crash when inline data creation follows DIO write
+    - ext4: fix null-ptr-deref in ext4_write_info
+    - ext4: make ext4_lazyinit_thread freezable
+    - ext4: fix check for block being out of directory size
+    - ext4: don't increase iversion counter for ea_inodes
+    - ext4: ext4_read_bh_lock() should submit IO if the buffer isn't uptodate
+    - ext4: place buffer head allocation before handle start
+    - ext4: fix dir corruption when ext4_dx_add_entry() fails
+    - ext4: fix miss release buffer head in ext4_fc_write_inode
+    - ext4: fix potential memory leak in ext4_fc_record_modified_inode()
+    - ext4: fix potential memory leak in ext4_fc_record_regions()
+    - ext4: update 'state->fc_regions_size' after successful memory allocation
+    - livepatch: fix race between fork and KLP transition
+    - ftrace: Properly unset FTRACE_HASH_FL_MOD
+    - ring-buffer: Allow splice to read previous partially read pages
+    - ring-buffer: Have the shortest_full queue be the shortest not longest
+    - ring-buffer: Check pending waiters when doing wake ups as well
+    - ring-buffer: Add ring_buffer_wake_waiters()
+    - ring-buffer: Fix race between reset page and reading page
+    - tracing: Disable interrupt or preemption before acquiring arch_spinlock_t
+    - tracing: Wake up ring buffer waiters on closing of the file
+    - tracing: Wake up waiters when tracing is disabled
+    - tracing: Add ioctl() to force ring buffer waiters to wake up
+    - tracing: Move duplicate code of trace_kprobe/eprobe.c into header
+    - tracing: Add "(fault)" name injection to kernel probes
+    - tracing: Fix reading strings from synthetic events
+    - thunderbolt: Explicitly enable lane adapter hotplug events at startup
+    - efi: libstub: drop pointless get_memory_map() call
+    - media: cedrus: Set the platform driver data earlier
+    - media: cedrus: Fix endless loop in cedrus_h265_skip_bits()
+    - blk-wbt: call rq_qos_add() after wb_normal is initialized
+    - KVM: x86/emulator: Fix handing of POP SS to correctly set interruptibility
+    - KVM: nVMX: Unconditionally purge queued/injected events on nested "exit"
+    - KVM: nVMX: Don't propagate vmcs12's PERF_GLOBAL_CTRL settings to vmcs02
+    - KVM: VMX: Drop bits 31:16 when shoving exception error code into VMCS
+    - staging: greybus: audio_helper: remove unused and wrong debugfs usage
+    - drm/nouveau/kms/nv140-: Disable interlacing
+    - drm/nouveau: fix a use-after-free in nouveau_gem_prime_import_sg_table()
+    - drm/i915: Fix watermark calculations for gen12+ RC CCS modifier
+    - drm/i915: Fix watermark calculations for gen12+ MC CCS modifier
+    - drm/i915: Fix watermark calculations for gen12+ CCS+CC modifier
+    - drm/amd/display: Fix vblank refcount in vrr transition
+    - smb3: must initialize two ACL struct fields to zero
+    - selinux: use "grep -E" instead of "egrep"
+    - ima: fix blocking of security.ima xattrs of unsupported algorithms
+    - userfaultfd: open userfaultfds with O_RDONLY
+    - ntfs3: rework xattr handlers and switch to POSIX ACL VFS helpers
+    - thermal: cpufreq_cooling: Check the policy first in
+      cpufreq_cooling_register()
+    - sh: machvec: Use char[] for section boundaries
+    - MIPS: SGI-IP27: Free some unused memory
+    - MIPS: SGI-IP27: Fix platform-device leak in bridge_platform_create()
+    - ARM: 9244/1: dump: Fix wrong pg_level in walk_pmd()
+    - ARM: 9247/1: mm: set readonly for MT_MEMORY_RO with ARM_LPAE
+    - objtool: Preserve special st_shndx indexes in elf_update_symbol
+    - nfsd: Fix a memory leak in an error handling path
+    - NFSD: Fix handling of oversized NFSv4 COMPOUND requests
+    - wifi: rtlwifi: 8192de: correct checking of IQK reload
+    - wifi: ath10k: add peer map clean up for peer delete in ath10k_sta_state()
+    - leds: lm3601x: Don't use mutex after it was destroyed
+    - bpf: Fix reference state management for synchronous callbacks
+    - wifi: mac80211: allow bw change during channel switch in mesh
+    - bpftool: Fix a wrong type cast in btf_dumper_int
+    - spi: mt7621: Fix an error message in mt7621_spi_probe()
+    - x86/resctrl: Fix to restore to original value when re-enabling hardware
+      prefetch register
+    - xsk: Fix backpressure mechanism on Tx
+    - bpf: Disable preemption when increasing per-cpu map_locked
+    - bpf: Propagate error from htab_lock_bucket() to userspace
+    - bpf: Use this_cpu_{inc|dec|inc_return} for bpf_task_storage_busy
+    - Bluetooth: btusb: mediatek: fix WMT failure during runtime suspend
+    - wifi: rtl8xxxu: tighten bounds checking in rtl8xxxu_read_efuse()
+    - wifi: rtw88: add missing destroy_workqueue() on error path in
+      rtw_core_init()
+    - selftests/xsk: Avoid use-after-free on ctx
+    - spi: qup: add missing clk_disable_unprepare on error in spi_qup_resume()
+    - spi: qup: add missing clk_disable_unprepare on error in
+      spi_qup_pm_resume_runtime()
+    - wifi: rtl8xxxu: Fix skb misuse in TX queue selection
+    - spi: meson-spicc: do not rely on busy flag in pow2 clk ops
+    - bpf: btf: fix truncated last_member_type_id in btf_struct_resolve
+    - wifi: rtl8xxxu: gen2: Fix mistake in path B IQ calibration
+    - wifi: rtl8xxxu: Remove copy-paste leftover in gen2_update_rate_mask
+    - wifi: mt76: sdio: fix transmitting packet hangs
+    - wifi: mt76: mt7615: add mt7615_mutex_acquire/release in
+      mt7615_sta_set_decap_offload
+    - wifi: mt76: mt7915: do not check state before configuring implicit beamform
+    - Bluetooth: RFCOMM: Fix possible deadlock on socket shutdown/release
+    - net: fs_enet: Fix wrong check in do_pd_setup
+    - bpf: Ensure correct locking around vulnerable function find_vpid()
+    - Bluetooth: hci_{ldisc,serdev}: check percpu_init_rwsem() failure
+    - netfilter: conntrack: fix the gc rescheduling delay
+    - netfilter: conntrack: revisit the gc initial rescheduling bias
+    - wifi: ath11k: fix number of VHT beamformee spatial streams
+    - x86/microcode/AMD: Track patch allocation size explicitly
+    - x86/cpu: Include the header of init_ia32_feat_ctl()'s prototype
+    - spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
+    - spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
+    - skmsg: Schedule psock work if the cached skb exists on the psock
+    - i2c: mlxbf: support lock mechanism
+    - Bluetooth: hci_core: Fix not handling link timeouts propertly
+    - xfrm: Reinject transport-mode packets through workqueue
+    - netfilter: nft_fib: Fix for rpath check with VRF devices
+    - spi: s3c64xx: Fix large transfers with DMA
+    - wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
+    - vhost/vsock: Use kvmalloc/kvfree for larger packets.
+    - eth: alx: take rtnl_lock on resume
+    - sctp: handle the error returned from sctp_auth_asoc_init_active_key
+    - tcp: fix tcp_cwnd_validate() to not forget is_cwnd_limited
+    - spi: Ensure that sg_table won't be used after being freed
+    - hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888
+      controller
+    - net: rds: don't hold sock lock when cancelling work from
+      rds_tcp_reset_callbacks()
+    - bnx2x: fix potential memory leak in bnx2x_tpa_stop()
+    - net: wwan: iosm: Call mutex_init before locking it
+    - net/ieee802154: reject zero-sized raw_sendmsg()
+    - once: add DO_ONCE_SLOW() for sleepable contexts
+    - net: mvpp2: fix mvpp2 debugfs leak
+    - drm: bridge: adv7511: fix CEC power down control register offset
+    - drm: bridge: adv7511: unregister cec i2c device after cec adapter
+    - drm/bridge: Avoid uninitialized variable warning
+    - drm/mipi-dsi: Detach devices when removing the host
+    - drm/virtio: Correct drm_gem_shmem_get_sg_table() error handling
+    - drm/bridge: parade-ps8640: Fix regulator supply order
+    - drm/dp_mst: fix drm_dp_dpcd_read return value checks
+    - drm:pl111: Add of_node_put() when breaking out of
+      for_each_available_child_of_node()
+    - ASoC: mt6359: fix tests for platform_get_irq() failure
+    - platform/chrome: fix double-free in chromeos_laptop_prepare()
+    - platform/chrome: fix memory corruption in ioctl
+    - ASoC: tas2764: Allow mono streams
+    - ASoC: tas2764: Drop conflicting set_bias_level power setting
+    - ASoC: tas2764: Fix mute/unmute
+    - platform/x86: msi-laptop: Fix old-ec check for backlight registering
+    - platform/x86: msi-laptop: Fix resource cleanup
+    - platform/chrome: cros_ec_typec: Correct alt mode index
+    - drm/amdgpu: add missing pci_disable_device() in
+      amdgpu_pmops_runtime_resume()
+    - drm/bridge: megachips: Fix a null pointer dereference bug
+    - ASoC: rsnd: Add check for rsnd_mod_power_on
+    - ALSA: hda: beep: Simplify keep-power-at-enable behavior
+    - drm/bochs: fix blanking
+    - drm/omap: dss: Fix refcount leak bugs
+    - drm/amdgpu: Fix memory leak in hpd_rx_irq_create_workqueue()
+    - mmc: au1xmmc: Fix an error handling path in au1xmmc_probe()
+    - ASoC: eureka-tlv320: Hold reference returned from of_find_xxx API
+    - drm/msm/dpu: index dpu_kms->hw_vbif using vbif_idx
+    - drm/msm/dp: correct 1.62G link rate at dp_catalog_ctrl_config_msa()
+    - drm/vmwgfx: Fix memory leak in vmw_mksstat_add_ioctl()
+    - ASoC: codecs: tx-macro: fix kcontrol put
+    - ASoC: da7219: Fix an error handling path in da7219_register_dai_clks()
+    - ALSA: dmaengine: increment buffer pointer atomically
+    - mmc: wmt-sdmmc: Fix an error handling path in wmt_mci_probe()
+    - ASoC: wm8997: Fix PM disable depth imbalance in wm8997_probe
+    - ASoC: wm5110: Fix PM disable depth imbalance in wm5110_probe
+    - ASoC: wm5102: Fix PM disable depth imbalance in wm5102_probe
+    - ASoC: mt6660: Fix PM disable depth imbalance in mt6660_i2c_probe
+    - ALSA: hda/hdmi: Don't skip notification handling during PM operation
+    - memory: pl353-smc: Fix refcount leak bug in pl353_smc_probe()
+    - memory: of: Fix refcount leak bug in of_get_ddr_timings()
+    - memory: of: Fix refcount leak bug in of_lpddr3_get_ddr_timings()
+    - locks: fix TOCTOU race when granting write lease
+    - soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
+    - soc: qcom: smem_state: Add refcounting for the 'state->of_node'
+    - ARM: dts: imx6qdl-kontron-samx6i: hook up DDC i2c bus
+    - ARM: dts: turris-omnia: Fix mpp26 pin name and comment
+    - ARM: dts: kirkwood: lsxl: fix serial line
+    - ARM: dts: kirkwood: lsxl: remove first ethernet port
+    - ia64: export memory_add_physaddr_to_nid to fix cxl build error
+    - soc/tegra: fuse: Drop Kconfig dependency on TEGRA20_APB_DMA
+    - arm64: dts: ti: k3-j7200: fix main pinmux range
+    - ARM: dts: exynos: correct s5k6a3 reset polarity on Midas family
+    - ARM: Drop CMDLINE_* dependency on ATAGS
+    - ext4: don't run ext4lazyinit for read-only filesystems
+    - arm64: ftrace: fix module PLTs with mcount
+    - ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
+    - iio: adc: at91-sama5d2_adc: fix AT91_SAMA5D2_MR_TRACKTIM_MAX
+    - iio: adc: at91-sama5d2_adc: check return status for pressure and touch
+    - iio: adc: at91-sama5d2_adc: lock around oversampling and sample freq
+    - iio: adc: at91-sama5d2_adc: disable/prepare buffer on suspend/resume
+    - iio: inkern: only release the device node when done with it
+    - iio: inkern: fix return value in devm_of_iio_channel_get_by_name()
+    - iio: ABI: Fix wrong format of differential capacitance channel ABI.
+    - iio: magnetometer: yas530: Change data type of hard_offsets to signed
+    - RDMA/mlx5: Don't compare mkey tags in DEVX indirect mkey
+    - usb: common: debug: Check non-standard control requests
+    - clk: meson: Hold reference returned by of_get_parent()
+    - clk: oxnas: Hold reference returned by of_get_parent()
+    - clk: qoriq: Hold reference returned by of_get_parent()
+    - clk: berlin: Add of_node_put() for of_get_parent()
+    - clk: sprd: Hold reference returned by of_get_parent()
+    - clk: tegra: Fix refcount leak in tegra210_clock_init
+    - clk: tegra: Fix refcount leak in tegra114_clock_init
+    - clk: tegra20: Fix refcount leak in tegra20_clock_init
+    - HSI: omap_ssi: Fix refcount leak in ssi_probe
+    - HSI: omap_ssi_port: Fix dma_map_sg error check
+    - media: exynos4-is: fimc-is: Add of_node_put() when breaking out of loop
+    - tty: xilinx_uartps: Fix the ignore_status
+    - media: meson: vdec: add missing clk_disable_unprepare on error in
+      vdec_hevc_start()
+    - media: uvcvideo: Fix memory leak in uvc_gpio_parse
+    - media: uvcvideo: Use entity get_cur in uvc_ctrl_set
+    - media: xilinx: vipp: Fix refcount leak in xvip_graph_dma_init
+    - RDMA/rxe: Fix "kernel NULL pointer dereference" error
+    - RDMA/rxe: Fix the error caused by qp->sk
+    - misc: ocxl: fix possible refcount leak in afu_ioctl()
+    - fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
+    - dmaengine: hisilicon: Disable channels when unregister hisi_dma
+    - dmaengine: hisilicon: Fix CQ head update
+    - dmaengine: hisilicon: Add multi-thread support for a DMA channel
+    - dyndbg: fix static_branch manipulation
+    - dyndbg: fix module.dyndbg handling
+    - dyndbg: let query-modname override actual module name
+    - dyndbg: drop EXPORTed dynamic_debug_exec_queries
+    - clk: qcom: sm6115: Select QCOM_GDSC
+    - mtd: devices: docg3: check the return value of devm_ioremap() in the probe
+    - phy: amlogic: phy-meson-axg-mipi-pcie-analog: Hold reference returned by
+      of_get_parent()
+    - phy: phy-mtk-tphy: fix the phy type setting issue
+    - mtd: rawnand: intel: Read the chip-select line from the correct OF node
+    - mtd: rawnand: intel: Remove undocumented compatible string
+    - mtd: rawnand: fsl_elbc: Fix none ECC mode
+    - RDMA/irdma: Align AE id codes to correct flush code and event
+    - RDMA/srp: Fix srp_abort()
+    - RDMA/siw: Always consume all skbuf data in sk_data_ready() upcall.
+    - RDMA/siw: Fix QP destroy to wait for all references dropped.
+    - ata: fix ata_id_sense_reporting_enabled() and ata_id_has_sense_reporting()
+    - ata: fix ata_id_has_devslp()
+    - ata: fix ata_id_has_ncq_autosense()
+    - ata: fix ata_id_has_dipm()
+    - mtd: rawnand: meson: fix bit map use in meson_nfc_ecc_correct()
+    - md/raid5: Ensure stripe_fill happens on non-read IO with journal
+    - md/raid5: Remove unnecessary bio_put() in raid5_read_one_chunk()
+    - RDMA/cm: Use SLID in the work completion as the DLID in responder side
+    - IB: Set IOVA/LENGTH on IB_MR in core/uverbs layers
+    - xhci: Don't show warning for reinit on known broken suspend
+    - usb: gadget: function: fix dangling pnp_string in f_printer.c
+    - drivers: serial: jsm: fix some leaks in probe
+    - serial: 8250: Toggle IER bits on only after irq has been set up
+    - tty: serial: fsl_lpuart: disable dma rx/tx use flags in lpuart_dma_shutdown
+    - phy: qualcomm: call clk_disable_unprepare in the error handling
+    - staging: vt6655: fix some erroneous memory clean-up loops
+    - slimbus: qcom-ngd-ctrl: allow compile testing without QCOM_RPROC_COMMON
+    - firmware: google: Test spinlock on panic path to avoid lockups
+    - serial: 8250: Fix restoring termios speed after suspend
+    - scsi: libsas: Fix use-after-free bug in smp_execute_task_sg()
+    - scsi: iscsi: Rename iscsi_conn_queue_work()
+    - scsi: iscsi: Add recv workqueue helpers
+    - scsi: iscsi: Run recv path from workqueue
+    - scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
+    - clk: qcom: apss-ipq6018: mark apcs_alias0_core_clk as critical
+    - clk: qcom: gcc-sm6115: Override default Alpha PLL regs
+    - RDMA/rxe: Fix resize_finish() in rxe_queue.c
+    - fsi: core: Check error number after calling ida_simple_get
+    - mfd: intel_soc_pmic: Fix an error handling path in
+      intel_soc_pmic_i2c_probe()
+    - mfd: fsl-imx25: Fix an error handling path in mx25_tsadc_setup_irq()
+    - mfd: lp8788: Fix an error handling path in lp8788_probe()
+    - mfd: lp8788: Fix an error handling path in lp8788_irq_init() and
+      lp8788_irq_init()
+    - mfd: fsl-imx25: Fix check for platform_get_irq() errors
+    - mfd: sm501: Add check for platform_driver_register()
+    - clk: mediatek: mt8183: mfgcfg: Propagate rate changes to parent
+    - dmaengine: ioat: stop mod_timer from resurrecting deleted timer in
+      __cleanup()
+    - usb: mtu3: fix failed runtime suspend in host only mode
+    - spmi: pmic-arb: correct duplicate APID to PPID mapping logic
+    - clk: vc5: Fix 5P49V6901 outputs disabling when enabling FOD
+    - clk: baikal-t1: Fix invalid xGMAC PTP clock divider
+    - clk: baikal-t1: Add shared xGMAC ref/ptp clocks internal parent
+    - clk: baikal-t1: Add SATA internal ref clock buffer
+    - clk: bcm2835: fix bcm2835_clock_rate_from_divisor declaration
+    - clk: imx: scu: fix memleak on platform_device_add() fails
+    - clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
+    - clk: ast2600: BCLK comes from EPLL
+    - mailbox: mpfs: fix handling of the reg property
+    - mailbox: mpfs: account for mbox offsets while sending
+    - mailbox: bcm-ferxrm-mailbox: Fix error check for dma_map_sg
+    - powerpc/configs: Properly enable PAPR_SCM in pseries_defconfig
+    - powerpc/math_emu/efp: Include module.h
+    - powerpc/sysdev/fsl_msi: Add missing of_node_put()
+    - powerpc/pci_dn: Add missing of_node_put()
+    - powerpc/powernv: add missing of_node_put() in opal_export_attrs()
+    - powerpc: Fix fallocate and fadvise64_64 compat parameter combination
+    - x86/hyperv: Fix 'struct hv_enlightened_vmcs' definition
+    - powerpc/64s: Fix GENERIC_CPU build flags for PPC970 / G5
+    - powerpc: Fix SPE Power ISA properties for e500v1 platforms
+    - powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
+    - powerpc/pseries/vas: Pass hw_cpu_id to node associativity HCALL
+    - crypto: sahara - don't sleep when in softirq
+    - crypto: hisilicon/zip - fix mismatch in get/set sgl_sge_nr
+    - hwrng: arm-smccc-trng - fix NO_ENTROPY handling
+    - cgroup: Honor caller's cgroup NS when resolving path
+    - hwrng: imx-rngc - Moving IRQ handler registering after
+      imx_rngc_irq_mask_clear()
+    - crypto: qat - fix default value of WDT timer
+    - crypto: hisilicon/qm - fix missing put dfx access
+    - cgroup/cpuset: Enable update_tasks_cpumask() on top_cpuset
+    - iommu/omap: Fix buffer overflow in debugfs
+    - crypto: akcipher - default implementation for setting a private key
+    - crypto: ccp - Release dma channels before dmaengine unrgister
+    - crypto: inside-secure - Change swab to swab32
+    - crypto: qat - fix DMA transfer direction
+    - cifs: return correct error in ->calc_signature()
+    - iommu/iova: Fix module config properly
+    - tracing: kprobe: Fix kprobe event gen test module on exit
+    - tracing: kprobe: Make gen test module work in arm and riscv
+    - tracing/osnoise: Fix possible recursive locking in stop_per_cpu_kthreads
+    - kbuild: remove the target in signal traps when interrupted
+    - kbuild: rpm-pkg: fix breakage when V=1 is used
+    - crypto: marvell/octeontx - prevent integer overflows
+    - crypto: cavium - prevent integer overflow loading firmware
+    - thermal/drivers/qcom/tsens-v0_1: Fix MSM8939 fourth sensor hw_id
+    - ACPI: APEI: do not add task_work to kernel thread to avoid memory leak
+    - f2fs: fix race condition on setting FI_NO_EXTENT flag
+    - f2fs: fix to account FS_CP_DATA_IO correctly
+    - selftest: tpm2: Add Client.__del__() to close /dev/tpm* handle
+    - fs: dlm: fix race in lowcomms
+    - rcu: Avoid triggering strict-GP irq-work when RCU is idle
+    - rcu: Back off upon fill_page_cache_func() allocation failure
+    - rcu-tasks: Convert RCU_LOCKDEP_WARN() to WARN_ONCE()
+    - ACPI: video: Add Toshiba Satellite/Portege Z830 quirk
+    - ACPI: tables: FPDT: Don't call acpi_os_map_memory() on invalid phys address
+    - cpufreq: intel_pstate: Add Tigerlake support in no-HWP mode
+    - MIPS: BCM47XX: Cast memcmp() of function to (void *)
+    - powercap: intel_rapl: fix UBSAN shift-out-of-bounds issue
+    - thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to
+      avoid crash
+    - ARM: decompressor: Include .data.rel.ro.local
+    - ACPI: x86: Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable
+    - x86/entry: Work around Clang __bdos() bug
+    - NFSD: Return nfserr_serverfault if splice_ok but buf->pages have data
+    - NFSD: fix use-after-free on source server when doing inter-server copy
+    - wifi: brcmfmac: fix invalid address access when enabling SCAN log level
+    - bpftool: Clear errno after libcap's checks
+    - ice: set tx_tstamps when creating new Tx rings via ethtool
+    - net: ethernet: ti: davinci_mdio: Add workaround for errata i2329
+    - openvswitch: Fix double reporting of drops in dropwatch
+    - openvswitch: Fix overreporting of drops in dropwatch
+    - tcp: annotate data-race around tcp_md5sig_pool_populated
+    - x86/mce: Retrieve poison range from hardware
+    - wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
+    - thunderbolt: Add back Intel Falcon Ridge end-to-end flow control workaround
+    - xfrm: Update ipcomp_scratches with NULL when freed
+    - iavf: Fix race between iavf_close and iavf_reset_task
+    - wifi: brcmfmac: fix use-after-free bug in brcmf_netdev_start_xmit()
+    - Bluetooth: btintel: Mark Intel controller to support LE_STATES quirk
+    - regulator: core: Prevent integer underflow
+    - wifi: mt76: mt7921: reset msta->airtime_ac while clearing up hw value
+    - Bluetooth: L2CAP: initialize delayed works at l2cap_chan_create()
+    - Bluetooth: hci_sysfs: Fix attempting to call device_add multiple times
+    - can: bcm: check the result of can_send() in bcm_can_tx()
+    - wifi: rt2x00: don't run Rt5592 IQ calibration on MT7620
+    - wifi: rt2x00: set correct TX_SW_CFG1 MAC register for MT7620
+    - wifi: rt2x00: set VGC gain for both chains of MT7620
+    - wifi: rt2x00: set SoC wmac clock register
+    - wifi: rt2x00: correctly set BBP register 86 for MT7620
+    - hwmon: (sht4x) do not overflow clamping operation on 32-bit platforms
+    - net: If sock is dead don't access sock's sk_wq in sk_stream_wait_memory
+    - Bluetooth: L2CAP: Fix user-after-free
+    - drm/nouveau/nouveau_bo: fix potential memory leak in nouveau_bo_alloc()
+    - drm: Use size_t type for len variable in drm_copy_field()
+    - drm: Prevent drm_copy_field() to attempt copying a NULL pointer
+    - drm/komeda: Fix handling of atomic commits in the atomic_commit_tail hook
+    - gpu: lontium-lt9611: Fix NULL pointer dereference in lt9611_connector_init()
+    - drm/amd/display: fix overflow on MIN_I64 definition
+    - udmabuf: Set ubuf->sg = NULL if the creation of sg table fails
+    - drm: bridge: dw_hdmi: only trigger hotplug event on link change
+    - ALSA: usb-audio: Register card at the last interface
+    - drm/vc4: vec: Fix timings for VEC modes
+    - drm: panel-orientation-quirks: Add quirk for Anbernic Win600
+    - platform/chrome: cros_ec: Notify the PM of wake events during resume
+    - platform/x86: msi-laptop: Change DMI match / alias strings to fix module
+      autoloading
+    - ASoC: SOF: pci: Change DMI match info to support all Chrome platforms
+    - drm/amdgpu: fix initial connector audio value
+    - drm/meson: reorder driver deinit sequence to fix use-after-free bug
+    - drm/meson: explicitly remove aggregate driver at module unload time
+    - mmc: sdhci-msm: add compatible string check for sdm670
+    - drm/dp: Don't rewrite link config when setting phy test pattern
+    - drm/amd/display: Remove interface for periodic interrupt 1
+    - ARM: dts: imx7d-sdb: config the max pressure for tsc2046
+    - ARM: dts: imx6q: add missing properties for sram
+    - ARM: dts: imx6dl: add missing properties for sram
+    - ARM: dts: imx6qp: add missing properties for sram
+    - ARM: dts: imx6sl: add missing properties for sram
+    - ARM: dts: imx6sll: add missing properties for sram
+    - ARM: dts: imx6sx: add missing properties for sram
+    - kselftest/arm64: Fix validatation termination record after EXTRA_CONTEXT
+    - arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply
+    - btrfs: dump extra info if one free space cache has more bitmaps than it
+      should
+    - btrfs: scrub: try to fix super block errors
+    - btrfs: don't print information about space cache or tree every remount
+    - ARM: 9242/1: kasan: Only map modules if CONFIG_KASAN_VMALLOC=n
+    - clk: zynqmp: Fix stack-out-of-bounds in strncpy`
+    - media: cx88: Fix a null-ptr-deref bug in buffer_prepare()
+    - media: platform: fix some double free in meson-ge2d and mtk-jpeg and s5p-mfc
+    - clk: zynqmp: pll: rectify rate rounding in zynqmp_pll_round_rate
+    - usb: host: xhci-plat: suspend and resume clocks
+    - usb: host: xhci-plat: suspend/resume clks for brcm
+    - dmaengine: ti: k3-udma: Reset UDMA_CHAN_RT byte counters to prevent overflow
+    - scsi: 3w-9xxx: Avoid disabling device if failing to enable it
+    - nbd: Fix hung when signal interrupts nbd_start_device_ioctl()
+    - iommu/arm-smmu-v3: Make default domain type of HiSilicon PTT device to
+      identity
+    - power: supply: adp5061: fix out-of-bounds read in adp5061_get_chg_type()
+    - staging: vt6655: fix potential memory leak
+    - blk-throttle: prevent overflow while calculating wait time
+    - ata: libahci_platform: Sanity check the DT child nodes number
+    - bcache: fix set_at_max_writeback_rate() for multiple attached devices
+    - soundwire: cadence: Don't overwrite msg->buf during write commands
+    - soundwire: intel: fix error handling on dai registration issues
+    - HID: roccat: Fix use-after-free in roccat_read()
+    - eventfd: guard wake_up in eventfd fs calls as well
+    - md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d
+    - usb: host: xhci: Fix potential memory leak in xhci_alloc_stream_info()
+    - usb: musb: Fix musb_gadget.c rxstate overflow bug
+    - arm64: dts: imx8mp: Add snps,gfladj-refclk-lpm-sel quirk to USB nodes
+    - usb: dwc3: core: Enable GUCTL1 bit 10 for fixing termination error after
+      resume bug
+    - Revert "usb: storage: Add quirk for Samsung Fit flash"
+    - staging: rtl8723bs: fix potential memory leak in rtw_init_drv_sw()
+    - staging: rtl8723bs: fix a potential memory leak in rtw_init_cmd_priv()
+    - scsi: tracing: Fix compile error in trace_array calls when TRACING is
+      disabled
+    - ext2: Use kvmalloc() for group descriptor array
+    - nvme: copy firmware_rev on each init
+    - nvmet-tcp: add bounds check on Transfer Tag
+    - usb: idmouse: fix an uninit-value in idmouse_open
+    - clk: bcm2835: Make peripheral PLLC critical
+    - clk: bcm2835: Round UART input clock up
+    - perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
+    - io_uring: correct pinned_vm accounting
+    - io_uring/rw: fix short rw error handling
+    - io_uring/rw: fix error'ed retry return values
+    - io_uring/rw: fix unexpected link breakage
+    - mm: hugetlb: fix UAF in hugetlb_handle_userfault
+    - net: ieee802154: return -EINVAL for unknown addr type
+    - ALSA: usb-audio: Fix last interface check for registration
+    - blk-wbt: fix that 'rwb->wc' is always set to 1 in wbt_init()
+    - [Config] updateconfigs for MDIO_BITBANG
+    - net: ethernet: ti: davinci_mdio: fix build for mdio bitbang uses
+    - Revert "net/ieee802154: reject zero-sized raw_sendmsg()"
+    - net/ieee802154: don't warn zero-sized raw_sendmsg()
+    - drm/amd/display: Fix build breakage with CONFIG_DEBUG_FS=n
+    - Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
+    - Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
+    - lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
+    - [Config] updateconfigs for AS_HAS_NON_CONST_LEB128
+    - ext4: continue to expand file system when the target size doesn't reach
+    - thermal: intel_powerclamp: Use first online CPU as control_cpu
+    - gcov: support GCC 12.1 and newer compilers
+    - io-wq: Fix memory leak in worker creation
+    - Linux 5.15.75
+  * [SRU] Ubuntu 22.04 - NVMe TCP - Host fails to reconnect to target after
+    link down/link up sequence (LP: #1989990)
+    - nvme-fabrics: parse nvme connect Linux error codes
+    - nvme-tcp: handle number of queue changes
+    - nvme-rdma: handle number of queue changes
+    - nvmet: expose max queues to configfs
+
+  [ Ubuntu: 5.15.0-58.64 ]
+
+  * jammy/linux: 5.15.0-58.64 -proposed tracker (LP: #2001670)
+  * CVE-2022-3643
+    - xen/netback: Ensure protocol headers don't fall in the non-linear area
+  * CVE-2022-4378
+    - proc: proc_skip_spaces() shouldn't think it is working on C strings
+    - proc: avoid integer type confusion in get_proc_long
+  * CVE-2022-45934
+    - Bluetooth: L2CAP: Fix u8 overflow
+  * CVE-2022-42896
+    - Bluetooth: L2CAP: Fix accepting connection request for invalid SPSM
+    - Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm
+
+  [ Ubuntu: 5.15.0-57.63 ]
+
+  * jammy/linux: 5.15.0-57.63 -proposed tracker (LP: #1997737)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2022.11.14)
+  * Expose built-in trusted and revoked certificates (LP: #1996892)
+    - [Packaging] Expose built-in trusted and revoked certificates
+  * TEE Support for CCP driver (LP: #1991608)
+    - crypto: ccp: Add support for TEE for PCI ID 0x14CA
+  * alsa: soc: the kernel print UBSAN calltrace on the machine with cs35l41
+    codec (LP: #1996121)
+    - ASoC: cs35l41: Add one more variable in the debug log
+    - ASoC: cs35l41: Fix an out-of-bounds access in otp_packed_element_t
+  * Fix ath11k deadlock on WCN6855 (LP: #1995041)
+    - wifi: ath11k: avoid deadlock during regulatory update in
+      ath11k_regd_update()
+  * [UBUNTU 20.04] boot: Add s390x secure boot trailer (LP: #1996071)
+    - s390/boot: add secure boot trailer
+  * Fix rfkill causing soft blocked wifi (LP: #1996198)
+    - platform/x86: hp_wmi: Fix rfkill causing soft blocked wifi
+  * Fix Thunderbolt device hotplug fail when connect via thunderbolt dock
+    (LP: #1991366)
+    - PCI: Fix used_buses calculation in pci_scan_child_bus_extend()
+    - PCI: Pass available buses even if the bridge is already configured
+    - PCI: Move pci_assign_unassigned_root_bus_resources()
+    - PCI: Distribute available resources for root buses, too
+    - PCI: Fix whitespace and indentation
+    - PCI: Fix typo in pci_scan_child_bus_extend()
+  * md: Replace snprintf with scnprintf (LP: #1993315)
+    - md: Replace snprintf with scnprintf
+  * input/keyboard: the keyboard on some Asus laptops can't work (LP: #1992266)
+    - ACPI: resource: Skip IRQ override on Asus Vivobook K3402ZA/K3502ZA
+    - ACPI: resource: Add ASUS model S5402ZA to quirks
+  * Fix Turbostat is not working for fam: 6 model: 191: stepping: 2 CPU
+    (LP: #1991365)
+    - tools/power turbostat: Add support for RPL-S
+  * pcieport 0000:00:1b.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal),
+    type=Transaction Layer, (Requester ID) (LP: #1988797)
+    - PCI/PTM: Cache PTM Capability offset
+    - PCI/PTM: Add pci_upstream_ptm() helper
+    - PCI/PTM: Separate configuration and enable
+    - PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
+    - PCI/PTM: Move pci_ptm_info() body into its only caller
+    - PCI/PTM: Preserve RsvdP bits in PTM Control register
+    - PCI/PTM: Reorder functions in logical order
+    - PCI/PTM: Consolidate PTM interface declarations
+    - PCI/PM: Always disable PTM for all devices during suspend
+    - PCI/PM: Simplify pci_pm_suspend_noirq()
+  * Fix RPL-S support on powercap/intel_rapl (LP: #1990161)
+    - x86/cpu: Drop spurious underscore from RAPTOR_LAKE #define
+    - x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
+    - x86/cpu: Add new Raptor Lake CPU model number
+    - powercap: intel_rapl: add support for RaptorLake
+    - powercap: intel_rapl: Add support for RAPTORLAKE_P
+    - powercap: intel_rapl: Add support for RAPTORLAKE_S
+  * AMD Yellow Carp system hang on HDMI plug in/out over HP hook2 docking
+    (LP: #1991974)
+    - drm/amd/display: Fix for link encoder access for MST.
+    - drm/amd/display: Fix MST link encoder availability check.
+    - drm/amd/display: FEC configuration for dpia links
+    - drm/amd/display: FEC configuration for dpia links in MST mode
+    - drm/amd/display: Add work around for tunneled MST.
+  * Jammy update: v5.15.74 upstream stable release (LP: #1995638)
+    - nilfs2: fix use-after-free bug of struct nilfs_root
+    - nilfs2: fix leak of nilfs_root in case of writer thread creation failure
+    - nilfs2: replace WARN_ONs by nilfs_error for checkpoint acquisition failure
+    - ceph: don't truncate file in atomic_open
+    - random: restore O_NONBLOCK support
+    - random: clamp credited irq bits to maximum mixed
+    - ALSA: hda: Fix position reporting on Poulsbo
+    - efi: Correct Macmini DMI match in uefi cert quirk
+    - USB: serial: qcserial: add new usb-id for Dell branded EM7455
+    - Revert "powerpc/rtas: Implement reentrant rtas call"
+    - Revert "crypto: qat - reduce size of mapped region"
+    - random: avoid reading two cache lines on irq randomness
+    - random: use expired timer rather than wq for mixing fast pool
+    - Input: xpad - add supported devices as contributed on github
+    - Input: xpad - fix wireless 360 controller breaking after suspend
+    - misc: pci_endpoint_test: Aggregate params checking for xfer
+    - misc: pci_endpoint_test: Fix pci_endpoint_test_{copy,write,read}() panic
+    - Linux 5.15.74
+  * Jammy update: v5.15.73 upstream stable release (LP: #1995637)
+    - Makefile.extrawarn: Move -Wcast-function-type-strict to W=1
+    - docs: update mediator information in CoC docs
+    - xsk: Inherit need_wakeup flag for shared sockets
+    - mm: gup: fix the fast GUP race against THP collapse
+    - powerpc/64s/radix: don't need to broadcast IPI for radix pmd collapse flush
+    - firmware: arm_scmi: Improve checks in the info_get operations
+    - firmware: arm_scmi: Harden accesses to the sensor domains
+    - firmware: arm_scmi: Add SCMI PM driver remove routine
+    - dmaengine: xilinx_dma: Fix devm_platform_ioremap_resource error handling
+    - dmaengine: xilinx_dma: cleanup for fetching xlnx,num-fstores property
+    - dmaengine: xilinx_dma: Report error in case of dma_set_mask_and_coherent API
+      failure
+    - ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
+    - scsi: qedf: Fix a UAF bug in __qedf_probe()
+    - net/ieee802154: fix uninit value bug in dgram_sendmsg
+    - net: marvell: prestera: add support for for Aldrin2
+    - ALSA: hda/hdmi: Fix the converter reuse for the silent stream
+    - um: Cleanup syscall_handler_t cast in syscalls_32.h
+    - um: Cleanup compiler warning in arch/x86/um/tls_32.c
+    - arch: um: Mark the stack non-executable to fix a binutils warning
+    - net: atlantic: fix potential memory leak in aq_ndev_close()
+    - drm/amd/display: Fix double cursor on non-video RGB MPO
+    - drm/amd/display: Assume an LTTPR is always present on fixed_vs links
+    - drm/amd/display: update gamut remap if plane has changed
+    - drm/amd/display: skip audio setup when audio stream is enabled
+    - mmc: core: Replace with already defined values for readability
+    - mmc: core: Terminate infinite loop in SD-UHS voltage switch
+    - perf parse-events: Identify broken modifiers
+    - mm/huge_memory: minor cleanup for split_huge_pages_all
+    - mm/huge_memory: use pfn_to_online_page() in split_huge_pages_all()
+    - wifi: cfg80211: fix MCS divisor value
+    - net/mlx5: Disable irq when locking lag_lock
+    - usb: mon: make mmapped memory read only
+    - USB: serial: ftdi_sio: fix 300 bps rate for SIO
+    - rpmsg: qcom: glink: replace strncpy() with strscpy_pad()
+    - Revert "clk: ti: Stop using legacy clkctrl names for omap4 and 5"
+    - Linux 5.15.73
+  * Jammy update: v5.15.72 upstream stable release (LP: #1995517)
+    - ALSA: hda: Do disconnect jacks at codec unbind
+    - ALSA: hda: Fix hang at HD-audio codec unbinding due to refcount saturation
+    - ALSA: hda: Fix Nvidia dp infoframe
+    - cgroup: reduce dependency on cgroup_mutex
+    - cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
+    - uas: add no-uas quirk for Hiksemi usb_disk
+    - usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS
+    - uas: ignore UAS for Thinkplus chips
+    - usb: typec: ucsi: Remove incorrect warning
+    - thunderbolt: Explicitly reset plug events delay back to USB4 spec value
+    - net: usb: qmi_wwan: Add new usb-id for Dell branded EM7455
+    - Input: snvs_pwrkey - fix SNVS_HPVIDR1 register address
+    - can: c_can: don't cache TX messages for C_CAN cores
+    - clk: ingenic-tcu: Properly enable registers before accessing timers
+    - x86/sgx: Do not fail on incomplete sanitization on premature stop of ksgxd
+    - ARM: dts: integrator: Tag PCI host with device_type
+    - ntfs: fix BUG_ON in ntfs_lookup_inode_by_name()
+    - mm/damon/dbgfs: fix memory leak when using debugfs_lookup()
+    - net: mt7531: only do PLL once after the reset
+    - Revert "firmware: arm_scmi: Add clock management to the SCMI power domain"
+    - drm/i915/gt: Restrict forced preemption to the active context
+    - drm/amdgpu: Add amdgpu suspend-resume code path under SRIOV
+    - vduse: prevent uninitialized memory accesses
+    - libata: add ATA_HORKAGE_NOLPM for Pioneer BDR-207M and BDR-205
+    - mmc: moxart: fix 4-bit bus width and remove 8-bit bus width
+    - mmc: hsq: Fix data stomping during mmc recovery
+    - mm/page_alloc: fix race condition between build_all_zonelists and page
+      allocation
+    - mm: prevent page_frag_alloc() from corrupting the memory
+    - mm: fix dereferencing possible ERR_PTR
+    - mm/migrate_device.c: flush TLB while holding PTL
+    - mm: fix madivse_pageout mishandling on non-LRU page
+    - mm,hwpoison: check mm when killing accessing process
+    - media: dvb_vb2: fix possible out of bound access
+    - media: rkvdec: Disable H.264 error detection
+    - media: v4l2-compat-ioctl32.c: zero buffer passed to
+      v4l2_compat_get_array_args()
+    - swiotlb: max mapping size takes min align mask into account
+    - ARM: dts: am33xx: Fix MMCHS0 dma properties
+    - reset: imx7: Fix the iMX8MP PCIe PHY PERST support
+    - ARM: dts: am5748: keep usb4_tm disabled
+    - soc: sunxi: sram: Actually claim SRAM regions
+    - soc: sunxi: sram: Prevent the driver from being unbound
+    - soc: sunxi_sram: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - soc: sunxi: sram: Fix probe function ordering issues
+    - soc: sunxi: sram: Fix debugfs info for A64 SRAM C
+    - ASoC: imx-card: Fix refcount issue with of_node_put
+    - arm64: dts: qcom: sm8350: fix UFS PHY serdes size
+    - ASoC: tas2770: Reinit regcache on reset
+    - drm/bridge: lt8912b: add vsync hsync
+    - drm/bridge: lt8912b: set hdmi or dvi mode
+    - drm/bridge: lt8912b: fix corrupted image output
+    - Revert "drm: bridge: analogix/dp: add panel prepare/unprepare in
+      suspend/resume time"
+    - Input: melfas_mip4 - fix return value check in mip4_probe()
+    - gpio: mvebu: Fix check for pwm support on non-A8K platforms
+    - usbnet: Fix memory leak in usbnet_disconnect()
+    - net: sched: act_ct: fix possible refcount leak in tcf_ct_init()
+    - cxgb4: fix missing unlock on ETHOFLD desc collect fail path
+    - net/mlxbf_gige: Fix an IS_ERR() vs NULL bug in mlxbf_gige_mdio_probe
+    - nvme: Fix IOC_PR_CLEAR and IOC_PR_RELEASE ioctls for nvme devices
+    - wifi: mac80211: fix regression with non-QoS drivers
+    - net: stmmac: power up/down serdes in stmmac_open/release
+    - net: phy: Don't WARN for PHY_UP state in mdio_bus_phy_resume()
+    - selftests: Fix the if conditions of in test_extra_filter()
+    - vdpa/ifcvf: fix the calculation of queuepair
+    - fs: split off setxattr_copy and do_setxattr function from setxattr
+    - clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks
+    - clk: iproc: Do not rely on node name for correct PLL setup
+    - KVM: x86: Hide IA32_PLATFORM_DCA_CAP[31:0] from the guest
+    - x86/alternative: Fix race in try_get_desc()
+    - drm/i915/gem: Really move i915_gem_context.link under ref protection
+    - Linux 5.15.72
+  * Jammy update: v5.15.71 upstream stable release (LP: #1995420)
+    - drm/amdgpu: Separate vf2pf work item init from virt data exchange
+    - drm/amdgpu: make sure to init common IP before gmc
+    - staging: r8188eu: Remove support for devices with 8188FU chipset (0bda:f179)
+    - staging: r8188eu: Add Rosewill USB-N150 Nano to device tables
+    - usb: dwc3: gadget: Avoid starting DWC3 gadget during UDC unbind
+    - usb: dwc3: Issue core soft reset before enabling run/stop
+    - usb: dwc3: gadget: Prevent repeat pullup()
+    - usb: dwc3: gadget: Refactor pullup()
+    - usb: dwc3: gadget: Don't modify GEVNTCOUNT in pullup()
+    - usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop
+    - usb: add quirks for Lenovo OneLink+ Dock
+    - usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
+    - Revert "usb: add quirks for Lenovo OneLink+ Dock"
+    - Revert "usb: gadget: udc-xilinx: replace memcpy with memcpy_toio"
+    - drivers/base: Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES
+    - USB: core: Fix RST error in hub.c
+    - USB: serial: option: add Quectel BG95 0x0203 composition
+    - USB: serial: option: add Quectel RM520N
+    - ALSA: core: Fix double-free at snd_card_new()
+    - ALSA: hda/tegra: set depop delay for tegra
+    - ALSA: hda: add Intel 5 Series / 3400 PCI DID
+    - ALSA: hda/realtek: Add quirk for Huawei WRT-WX9
+    - ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5570 laptop
+    - ALSA: hda/realtek: Re-arrange quirk table entries
+    - ALSA: hda/realtek: Add pincfg for ASUS G513 HP jack
+    - ALSA: hda/realtek: Add pincfg for ASUS G533Z HP jack
+    - ALSA: hda/realtek: Add quirk for ASUS GA503R laptop
+    - ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5530 laptop
+    - iommu/vt-d: Check correct capability for sagaw determination
+    - btrfs: fix hang during unmount when stopping block group reclaim worker
+    - btrfs: fix hang during unmount when stopping a space reclaim worker
+    - media: flexcop-usb: fix endpoint type check
+    - usb: dwc3: core: leave default DMA if the controller does not support 64-bit
+      DMA
+    - efi: x86: Wipe setup_data on pure EFI boot
+    - efi: libstub: check Shim mode using MokSBStateRT
+    - wifi: mt76: fix reading current per-tid starting sequence number for
+      aggregation
+    - gpio: mockup: fix NULL pointer dereference when removing debugfs
+    - gpio: mockup: Fix potential resource leakage when register a chip
+    - gpiolib: cdev: Set lineevent_state::irq after IRQ register successfully
+    - riscv: fix a nasty sigreturn bug...
+    - kasan: call kasan_malloc() from __kmalloc_*track_caller()
+    - can: flexcan: flexcan_mailbox_read() fix return value for drop = true
+    - net: mana: Add rmb after checking owner bits
+    - mm/slub: fix to return errno if kmalloc() fails
+    - mm: slub: fix flush_cpu_slab()/__free_slab() invocations in task context.
+    - KVM: x86: Inject #UD on emulated XSETBV if XSAVES isn't enabled
+    - arm64: topology: fix possible overflow in amu_fie_setup()
+    - vmlinux.lds.h: CFI: Reduce alignment of jump-table to function alignment
+    - xfs: reorder iunlink remove operation in xfs_ifree
+    - xfs: fix xfs_ifree() error handling to not leak perag ref
+    - xfs: validate inode fork size against fork format
+    - firmware: arm_scmi: Harden accesses to the reset domains
+    - firmware: arm_scmi: Fix the asynchronous reset requests
+    - arm64: dts: rockchip: Pull up wlan wake# on Gru-Bob
+    - arm64: dts: rockchip: Fix typo in lisense text for PX30.Core
+    - drm/mediatek: dsi: Add atomic {destroy,duplicate}_state, reset callbacks
+    - arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
+    - dmaengine: ti: k3-udma-private: Fix refcount leak bug in of_xudma_dev_get()
+    - arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
+    - netfilter: nf_conntrack_sip: fix ct_sip_walk_headers
+    - netfilter: nf_conntrack_irc: Tighten matching on DCC message
+    - netfilter: nfnetlink_osf: fix possible bogus match in nf_osf_find()
+    - ice: Don't double unplug aux on peer initiated reset
+    - iavf: Fix cached head and tail value for iavf_get_tx_pending
+    - ipvlan: Fix out-of-bound bugs caused by unset skb->mac_header
+    - net: core: fix flow symmetric hash
+    - net: phy: aquantia: wait for the suspend/resume operations to finish
+    - scsi: qla2xxx: Fix memory leak in __qlt_24xx_handle_abts()
+    - scsi: mpt3sas: Fix return value check of dma_get_required_mask()
+    - net: bonding: Share lacpdu_mcast_addr definition
+    - net: bonding: Unsync device addresses on ndo_stop
+    - net: team: Unsync device addresses on ndo_stop
+    - drm/panel: simple: Fix innolux_g121i1_l01 bus_format
+    - MIPS: lantiq: export clk_get_io() for lantiq_wdt.ko
+    - MIPS: Loongson32: Fix PHY-mode being left unspecified
+    - um: fix default console kernel parameter
+    - iavf: Fix bad page state
+    - mlxbf_gige: clear MDIO gateway lock after read
+    - i40e: Fix set max_tx_rate when it is lower than 1 Mbps
+    - sfc: fix TX channel offset when using legacy interrupts
+    - sfc: fix null pointer dereference in efx_hard_start_xmit
+    - drm/hisilicon/hibmc: Allow to be built if COMPILE_TEST is enabled
+    - drm/hisilicon: Add depends on MMU
+    - of: mdio: Add of_node_put() when breaking out of for_each_xx
+    - net: ipa: properly limit modem routing table use
+    - wireguard: ratelimiter: disable timings test by default
+    - wireguard: netlink: avoid variable-sized memcpy on sockaddr
+    - net: enetc: move enetc_set_psfp() out of the common enetc_set_features()
+    - net: enetc: deny offload of tc-based TSN features on VF interfaces
+    - net/sched: taprio: avoid disabling offload when it was never enabled
+    - net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo child
+      qdiscs
+    - netfilter: nf_tables: fix nft_counters_enabled underflow at
+      nf_tables_addchain()
+    - netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
+    - netfilter: ebtables: fix memory leak when blob is malformed
+    - net: ravb: Fix PHY state warning splat during system resume
+    - net: sh_eth: Fix PHY state warning splat during system resume
+    - can: gs_usb: gs_can_open(): fix race dev->can.state condition
+    - perf stat: Fix BPF program section name
+    - perf jit: Include program header in ELF files
+    - perf kcore_copy: Do not check /proc/modules is unchanged
+    - perf tools: Honor namespace when synthesizing build-ids
+    - drm/mediatek: dsi: Move mtk_dsi_stop() call back to mtk_dsi_poweroff()
+    - net/smc: Stop the CLC flow if no link to map buffers on
+    - bonding: fix NULL deref in bond_rr_gen_slave_id
+    - net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD
+    - net: sched: fix possible refcount leak in tc_new_tfilter()
+    - bnxt: prevent skb UAF after handing over to PTP worker
+    - selftests: forwarding: add shebang for sch_red.sh
+    - KVM: x86/mmu: Fold rmap_recycle into rmap_add
+    - serial: fsl_lpuart: Reset prior to registration
+    - serial: Create uart_xmit_advance()
+    - serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
+    - serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
+    - s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup
+    - drm/amd/amdgpu: fixing read wrong pf2vf data in SRIOV
+    - Drivers: hv: Never allocate anything besides framebuffer from framebuffer
+      memory region
+    - drm/gma500: Fix BUG: sleeping function called from invalid context errors
+    - drm/amd/pm: disable BACO entry/exit completely on several sienna cichlid
+      cards
+    - drm/amdgpu: use dirty framebuffer helper
+    - drm/amd/display: Limit user regamma to a valid value
+    - drm/amd/display: Reduce number of arguments of dml31's
+      CalculateWatermarksAndDRAMSpeedChangeSupport()
+    - drm/amd/display: Reduce number of arguments of dml31's
+      CalculateFlipSchedule()
+    - drm/amd/display: Mark dml30's UseMinimumDCFCLK() as noinline for stack usage
+    - drm/rockchip: Fix return type of cdn_dp_connector_mode_valid
+    - fsdax: Fix infinite loop in dax_iomap_rw()
+    - workqueue: don't skip lockdep work dependency in cancel_work_sync()
+    - i2c: imx: If pm_runtime_get_sync() returned 1 device access is possible
+    - i2c: mlxbf: incorrect base address passed during io write
+    - i2c: mlxbf: prevent stack overflow in mlxbf_i2c_smbus_start_transaction()
+    - i2c: mlxbf: Fix frequency calculation
+    - drm/amdgpu: don't register a dirty callback for non-atomic
+    - NFSv4: Fixes for nfs4_inode_return_delegation()
+    - devdax: Fix soft-reservation memory description
+    - ext4: make directory inode spreading reflect flexbg size
+    - ext4: fix bug in extents parsing when eh_entries == 0 and eh_depth > 0
+    - ext4: limit the number of retries after discarding preallocations blocks
+    - ext4: make mballoc try target group first even with mb_optimize_scan
+    - ext4: avoid unnecessary spreading of allocations among groups
+    - ext4: use locality group preallocation for small closed files
+    - Linux 5.15.71
+    - Revert "drm/amdgpu: use dirty framebuffer helper"
+  * Jammy update: v5.15.70 upstream stable release (LP: #1995415)
+    - drm/tegra: vic: Fix build warning when CONFIG_PM=n
+    - serial: atmel: remove redundant assignment in rs485_config
+    - tty: serial: atmel: Preserve previous USART mode if RS485 disabled
+    - of: fdt: fix off-by-one error in unflatten_dt_nodes()
+    - pinctrl: qcom: sc8180x: Fix gpio_wakeirq_map
+    - pinctrl: qcom: sc8180x: Fix wrong pin numbers
+    - pinctrl: rockchip: Enhance support for IRQ_TYPE_EDGE_BOTH
+    - pinctrl: sunxi: Fix name for A100 R_PIO
+    - NFSv4: Turn off open-by-filehandle and NFS re-export for NFSv4.0
+    - gpio: mpc8xxx: Fix support for IRQ_TYPE_LEVEL_LOW flow_type in mpc85xx
+    - drm/meson: Correct OSD1 global alpha value
+    - drm/meson: Fix OSD1 RGB to YCbCr coefficient
+    - block: blk_queue_enter() / __bio_queue_enter() must return -EAGAIN for
+      nowait
+    - parisc: ccio-dma: Add missing iounmap in error path in ccio_probe()
+    - of/device: Fix up of_dma_configure_id() stub
+    - cifs: revalidate mapping when doing direct writes
+    - cifs: don't send down the destination address to sendmsg for a SOCK_STREAM
+    - cifs: always initialize struct msghdr smb_msg completely
+    - parisc: Allow CONFIG_64BIT with ARCH=parisc
+    - tools/include/uapi: Fix <asm/errno.h> for parisc and xtensa
+    - drm/amdgpu: Don't enable LTR if not supported
+    - drm/amdgpu: move nbio ih_doorbell_range() into ih code for vega
+    - drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega
+    - binder: remove inaccurate mmap_assert_locked()
+    - arm64: dts: juno: Add missing MHU secure-irq
+    - ASoC: nau8824: Fix semaphore unbalance at error paths
+    - regulator: pfuze100: Fix the global-out-of-bounds access in
+      pfuze100_regulator_probe()
+    - scsi: lpfc: Return DID_TRANSPORT_DISRUPTED instead of DID_REQUEUE
+    - rxrpc: Fix local destruction being repeated
+    - rxrpc: Fix calc of resend age
+    - wifi: mac80211_hwsim: check length for virtio packets
+    - ALSA: hda/sigmatel: Keep power up while beep is enabled
+    - ALSA: hda/tegra: Align BDL entry to 4KB boundary
+    - net: usb: qmi_wwan: add Quectel RM520N
+    - afs: Return -EAGAIN, not -EREMOTEIO, when a file already locked
+    - MIPS: OCTEON: irq: Fix octeon_irq_force_ciu_mapping()
+    - drm/panfrost: devfreq: set opp to the recommended one to configure regulator
+    - mksysmap: Fix the mismatch of 'L0' symbols in System.map
+    - video: fbdev: pxa3xx-gcu: Fix integer overflow in pxa3xx_gcu_write
+    - net: Find dst with sk's xfrm policy not ctl_sk
+    - KVM: SEV: add cache flush to solve SEV cache incoherency issues
+    - cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all()
+    - ALSA: hda/sigmatel: Fix unused variable warning for beep power change
+    - Linux 5.15.70
+  * Jammy update: v5.15.69 upstream stable release (LP: #1993010)
+    - NFS: Fix WARN_ON due to unionization of nfs_inode.nrequests
+    - ACPI: resource: skip IRQ override on AMD Zen platforms
+    - ARM: dts: imx: align SPI NOR node name with dtschema
+    - ARM: dts: imx6qdl-kontron-samx6i: fix spi-flash compatible
+    - ARM: dts: at91: fix low limit for CPU regulator
+    - ARM: dts: at91: sama7g5ek: specify proper regulator output ranges
+    - lockdep: Fix -Wunused-parameter for _THIS_IP_
+    - x86/mm: Force-inline __phys_addr_nodebug()
+    - task_stack, x86/cea: Force-inline stack helpers
+    - tracing: hold caller_addr to hardirq_{enable,disable}_ip
+    - tracefs: Only clobber mode/uid/gid on remount if asked
+    - iommu/vt-d: Fix kdump kernels boot failure with scalable mode
+    - Input: goodix - add support for GT1158
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Go 2
+    - drm/msm/rd: Fix FIFO-full deadlock
+    - dt-bindings: iio: gyroscope: bosch,bmg160: correct number of pins
+    - HID: ishtp-hid-clientHID: ishtp-hid-client: Fix comment typo
+    - hid: intel-ish-hid: ishtp: Fix ishtp client sending disordered message
+    - tg3: Disable tg3 device on system reboot to avoid triggering AER
+    - gpio: mockup: remove gpio debugfs when remove device
+    - ieee802154: cc2520: add rc code in cc2520_tx()
+    - Input: iforce - add support for Boeder Force Feedback Wheel
+    - nvmet-tcp: fix unhandled tcp states in nvmet_tcp_state_change()
+    - drm/amd/amdgpu: skip ucode loading if ucode_size == 0
+    - net: dsa: hellcreek: Print warning only once
+    - perf/arm_pmu_platform: fix tests for platform_get_irq() failure
+    - platform/x86: acer-wmi: Acer Aspire One AOD270/Packard Bell Dot keymap fixes
+    - usb: storage: Add ASUS <0x0b05:0x1932> to IGNORE_UAS
+    - mm: Fix TLB flush for not-first PFNMAP mappings in unmap_region()
+    - soc: fsl: select FSL_GUTS driver for DPIO
+    - usb: gadget: f_uac2: clean up some inconsistent indenting
+    - usb: gadget: f_uac2: fix superspeed transfer
+    - RDMA/irdma: Use s/g array in post send only when its valid
+    - Input: goodix - add compatible string for GT1158
+    - Linux 5.15.69
+  * Jammy update: v5.15.68 upstream stable release (LP: #1993003)
+    - net: wwan: iosm: remove pointless null check
+    - efi: libstub: Disable struct randomization
+    - efi: capsule-loader: Fix use-after-free in efi_capsule_write
+    - wifi: iwlegacy: 4965: corrected fix for potential off-by-one overflow in
+      il4965_rs_fill_link_cmd()
+    - fs: only do a memory barrier for the first set_buffer_uptodate()
+    - Revert "mm: kmemleak: take a full lowmem check in kmemleak_*_phys()"
+    - scsi: qla2xxx: Disable ATIO interrupt coalesce for quad port ISP27XX
+    - scsi: megaraid_sas: Fix double kfree()
+    - drm/gem: Fix GEM handle release errors
+    - drm/amdgpu: Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
+      psp_hw_fini
+    - drm/amdgpu: Check num_gfx_rings for gfx v9_0 rb setup.
+    - drm/radeon: add a force flush to delay work when radeon
+    - scsi: ufs: core: Reduce the power mode change timeout
+    - Revert "parisc: Show error if wrong 32/64-bit compiler is being used"
+    - parisc: ccio-dma: Handle kmalloc failure in ccio_init_resources()
+    - parisc: Add runtime check to prevent PA2.0 kernels on PA1.x machines
+    - arm64: cacheinfo: Fix incorrect assignment of signed error value to unsigned
+      fw_level
+    - netfilter: conntrack: work around exceeded receive window
+    - cpufreq: check only freq_table in __resolve_freq()
+    - net/core/skbuff: Check the return value of skb_copy_bits()
+    - md: Flush workqueue md_rdev_misc_wq in md_alloc()
+    - fbdev: fbcon: Destroy mutex on freeing struct fb_info
+    - fbdev: chipsfb: Add missing pci_disable_device() in chipsfb_pci_init()
+    - drm/amdgpu: mmVM_L2_CNTL3 register not initialized correctly
+    - ALSA: pcm: oss: Fix race at SNDCTL_DSP_SYNC
+    - ALSA: emu10k1: Fix out of bounds access in snd_emu10k1_pcm_channel_alloc()
+    - ALSA: aloop: Fix random zeros in capture data when using jiffies timer
+    - ALSA: usb-audio: Fix an out-of-bounds bug in
+      __snd_usb_parse_audio_interface()
+    - tracing: Fix to check event_mutex is held while accessing trigger list
+    - btrfs: zoned: set pseudo max append zone limit in zone emulation mode
+    - vfio/type1: Unpin zero pages
+    - kprobes: Prohibit probes in gate area
+    - debugfs: add debugfs_lookup_and_remove()
+    - sched/debug: fix dentry leak in update_sched_domain_debugfs
+    - drm/amd/display: fix memory leak when using debugfs_lookup()
+    - nvmet: fix a use-after-free
+    - scsi: mpt3sas: Fix use-after-free warning
+    - scsi: lpfc: Add missing destroy_workqueue() in error path
+    - NFS: Further optimisations for 'ls -l'
+    - NFS: Save some space in the inode
+    - NFS: Fix another fsync() issue after a server reboot
+    - cgroup: Elide write-locking threadgroup_rwsem when updating csses on an
+      empty subtree
+    - cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock
+    - ASoC: qcom: sm8250: add missing module owner
+    - RDMA/rtrs-clt: Use the right sg_cnt after ib_dma_map_sg
+    - RDMA/rtrs-srv: Pass the correct number of entries for dma mapped SGL
+    - ARM: dts: imx6qdl-kontron-samx6i: remove duplicated node
+    - soc: imx: gpcv2: Assert reset before ungating clock
+    - regulator: core: Clean up on enable failure
+    - tee: fix compiler warning in tee_shm_register()
+    - RDMA/cma: Fix arguments order in net device validation
+    - soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugs
+    - RDMA/hns: Fix supported page size
+    - RDMA/hns: Fix wrong fixed value of qp->rq.wqe_shift
+    - wifi: wilc1000: fix DMA on stack objects
+    - ARM: at91: pm: fix self-refresh for sama7g5
+    - ARM: at91: pm: fix DDR recalibration when resuming from backup and self-
+      refresh
+    - ARM: dts: at91: sama5d27_wlsom1: specify proper regulator output ranges
+    - ARM: dts: at91: sama5d2_icp: specify proper regulator output ranges
+    - ARM: dts: at91: sama5d27_wlsom1: don't keep ldo2 enabled all the time
+    - ARM: dts: at91: sama5d2_icp: don't keep vdd_other enabled all the time
+    - netfilter: br_netfilter: Drop dst references before setting.
+    - netfilter: nf_tables: clean up hook list when offload flags check fails
+    - RDMA/srp: Set scmnd->result only when scmnd is not NULL
+    - ALSA: usb-audio: Inform the delayed registration more properly
+    - ALSA: usb-audio: Register card again for iface over delayed_register option
+    - rxrpc: Fix ICMP/ICMP6 error handling
+    - rxrpc: Fix an insufficiently large sglist in rxkad_verify_packet_2()
+    - afs: Use the operation issue time instead of the reply time for callbacks
+    - Revert "net: phy: meson-gxl: improve link-up behavior"
+    - sch_sfb: Don't assume the skb is still around after enqueueing to child
+    - tipc: fix shift wrapping bug in map_get()
+    - net: introduce __skb_fill_page_desc_noacc
+    - tcp: TX zerocopy should not sense pfmemalloc status
+    - ice: use bitmap_free instead of devm_kfree
+    - i40e: Fix kernel crash during module removal
+    - iavf: Detach device during reset task
+    - xen-netback: only remove 'hotplug-status' when the vif is actually destroyed
+    - RDMA/siw: Pass a pointer to virt_to_page()
+    - ipv6: sr: fix out-of-bounds read when setting HMAC data.
+    - IB/core: Fix a nested dead lock as part of ODP flow
+    - RDMA/mlx5: Set local port to one when accessing counters
+    - erofs: fix pcluster use-after-free on UP platforms
+    - nvme-tcp: fix UAF when detecting digest errors
+    - nvme-tcp: fix regression that causes sporadic requests to time out
+    - tcp: fix early ETIMEDOUT after spurious non-SACK RTO
+    - nvmet: fix mar and mor off-by-one errors
+    - RDMA/irdma: Report the correct max cqes from query device
+    - RDMA/irdma: Return correct WC error for bind operation failure
+    - RDMA/irdma: Report RNR NAK generation in device caps
+    - sch_sfb: Also store skb len before calling child enqueue
+    - perf script: Fix Cannot print 'iregs' field for hybrid systems
+    - hwmon: (tps23861) fix byte order in resistance register
+    - ASoC: mchp-spdiftx: remove references to mchp_i2s_caps
+    - ASoC: mchp-spdiftx: Fix clang -Wbitfield-constant-conversion
+    - MIPS: loongson32: ls1c: Fix hang during startup
+    - kbuild: disable header exports for UML in a straightforward way
+    - i40e: Refactor tc mqprio checks
+    - i40e: Fix ADQ rate limiting for PF
+    - swiotlb: avoid potential left shift overflow
+    - iommu/amd: use full 64-bit value in build_completion_wait()
+    - s390/boot: fix absolute zero lowcore corruption on boot
+    - hwmon: (mr75203) fix VM sensor allocation when "intel,vm-map" not defined
+    - hwmon: (mr75203) update pvt->v_num and vm_num to the actual number of used
+      sensors
+    - hwmon: (mr75203) fix voltage equation for negative source input
+    - hwmon: (mr75203) fix multi-channel voltage reading
+    - hwmon: (mr75203) enable polling for all VM channels
+    - arm64/bti: Disable in kernel BTI when cross section thunks are broken
+    - [Config] updateconfigs for ARM64_BTI_KERNEL
+    - iommu/vt-d: Correctly calculate sagaw value of IOMMU
+    - [Config] updateconfigs for ARM64_ERRATUM_2457168
+    - arm64: errata: add detection for AMEVCNTR01 incrementing incorrectly
+    - drm/bridge: display-connector: implement bus fmts callbacks
+    - perf machine: Use path__join() to compose a path instead of snprintf(dir,
+      '/', filename)
+    - ARM: at91: ddr: remove CONFIG_SOC_SAMA7 dependency
+    - Linux 5.15.68
+  * Jammy update: v5.15.67 upstream stable release (LP: #1991841)
+    - Linux 5.15.67
+  * Jammy update: v5.15.66 upstream stable release (LP: #1991840)
+    - drm/msm/dsi: fix the inconsistent indenting
+    - drm/msm/dp: delete DP_RECOVERED_CLOCK_OUT_EN to fix tps4
+    - drm/msm/dsi: Fix number of regulators for msm8996_dsi_cfg
+    - drm/msm/dsi: Fix number of regulators for SDM660
+    - platform/x86: pmc_atom: Fix SLP_TYPx bitfield mask
+    - iio: adc: mcp3911: make use of the sign bit
+    - skmsg: Fix wrong last sg check in sk_msg_recvmsg()
+    - bpf: Restrict bpf_sys_bpf to CAP_PERFMON
+    - bpf, cgroup: Fix kernel BUG in purge_effective_progs
+    - ieee802154/adf7242: defer destroy_workqueue call
+    - drm/i915/backlight: extract backlight code to a separate file
+    - drm/i915/display: avoid warnings when registering dual panel backlight
+    - ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
+    - ALSA: hda: intel-nhlt: Correct the handling of fmt_config flexible array
+    - wifi: cfg80211: debugfs: fix return type in ht40allow_map_read()
+    - Revert "xhci: turn off port power in shutdown"
+    - net: sparx5: fix handling uneven length packets in manual extraction
+    - net: smsc911x: Stop and start PHY during suspend and resume
+    - openvswitch: fix memory leak at failed datapath creation
+    - net: dsa: xrs700x: Use irqsave variant for u64 stats update
+    - net: sched: tbf: don't call qdisc_put() while holding tree lock
+    - net/sched: fix netdevice reference leaks in attach_default_qdiscs()
+    - ethernet: rocker: fix sleep in atomic context bug in neigh_timer_handler
+    - mlxbf_gige: compute MDIO period based on i1clk
+    - kcm: fix strp_init() order and cleanup
+    - sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb
+    - tcp: annotate data-race around challenge_timestamp
+    - Revert "sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb"
+    - net/smc: Remove redundant refcount increase
+    - soundwire: qcom: fix device status array range
+    - serial: fsl_lpuart: RS485 RTS polariy is inverse
+    - staging: rtl8712: fix use after free bugs
+    - staging: r8188eu: add firmware dependency
+    - powerpc: align syscall table for ppc32
+    - vt: Clear selection before changing the font
+    - musb: fix USB_MUSB_TUSB6010 dependency
+    - tty: serial: lpuart: disable flow control while waiting for the transmit
+      engine to complete
+    - Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
+    - iio: ad7292: Prevent regulator double disable
+    - iio: adc: mcp3911: use correct formula for AD conversion
+    - misc: fastrpc: fix memory corruption on probe
+    - misc: fastrpc: fix memory corruption on open
+    - USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
+    - mmc: core: Fix UHS-I SD 1.8V workaround branch
+    - mmc: core: Fix inconsistent sd3_bus_mode at UHS-I SD voltage switch failure
+    - binder: fix UAF of ref->proc caused by race condition
+    - binder: fix alloc->vma_vm_mm null-ptr dereference
+    - cifs: fix small mempool leak in SMB2_negotiate()
+    - KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
+    - drm/i915/reg: Fix spelling mistake "Unsupport" -> "Unsupported"
+    - clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops
+    - Revert "clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops"
+    - clk: core: Fix runtime PM sequence in clk_core_unprepare()
+    - Input: rk805-pwrkey - fix module autoloading
+    - clk: bcm: rpi: Fix error handling of raspberrypi_fw_get_rate
+    - clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()
+    - clk: bcm: rpi: Prevent out-of-bounds access
+    - clk: bcm: rpi: Add missing newline
+    - hwmon: (gpio-fan) Fix array out of bounds access
+    - gpio: pca953x: Add mutex_lock for regcache sync in PM
+    - KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
+    - xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
+    - mm: pagewalk: Fix race between unmap and page walker
+    - xen-blkback: Advertise feature-persistent as user requested
+    - xen-blkfront: Advertise feature-persistent as user requested
+    - xen-blkfront: Cache feature_persistent value before advertisement
+    - thunderbolt: Use the actual buffer in tb_async_error()
+    - usb: dwc3: pci: Add support for Intel Raptor Lake
+    - media: mceusb: Use new usb_control_msg_*() routines
+    - xhci: Add grace period after xHC start to prevent premature runtime suspend.
+    - USB: serial: cp210x: add Decagon UCA device id
+    - USB: serial: option: add support for OPPO R11 diag port
+    - USB: serial: option: add Quectel EM060K modem
+    - USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
+    - usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles
+    - usb: typec: intel_pmc_mux: Add new ACPI ID for Meteor Lake IOM device
+    - usb: typec: tcpm: Return ENOTSUPP for power supply prop writes
+    - usb: dwc2: fix wrong order of phy_power_on and phy_init
+    - usb: cdns3: fix issue with rearming ISO OUT endpoint
+    - usb: cdns3: fix incorrect handling TRB_SMM flag for ISOC transfer
+    - USB: cdc-acm: Add Icom PMR F3400 support (0c26:0020)
+    - usb-storage: Add ignore-residue quirk for NXP PN7462AU
+    - s390/hugetlb: fix prepare_hugepage_range() check for 2 GB hugepages
+    - s390: fix nospec table alignments
+    - USB: core: Prevent nested device-reset calls
+    - usb: xhci-mtk: relax TT periodic bandwidth allocation
+    - usb: xhci-mtk: fix bandwidth release issue
+    - usb: gadget: mass_storage: Fix cdrom data transfers on MAC-OS
+    - driver core: Don't probe devices after bus_type.match() probe deferral
+    - wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected
+    - wifi: mac80211: Fix UAF in ieee80211_scan_rx()
+    - net: Use u64_stats_fetch_begin_irq() for stats fetch.
+    - net: mac802154: Fix a condition in the receive path
+    - ALSA: hda/realtek: Add speaker AMP init for Samsung laptops with ALC298
+    - ALSA: seq: oss: Fix data-race for max_midi_devs access
+    - ALSA: seq: Fix data-race at module auto-loading
+    - drm/i915/glk: ECS Liva Q2 needs GLK HDMI port timing quirk
+    - drm/i915: Skip wm/ddb readout for disabled pipes
+    - tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()
+    - kbuild: Add skip_encoding_btf_enum64 option to pahole
+    - usb: dwc3: fix PHY disable sequence
+    - usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup
+    - usb: dwc3: disable USB core PHY management
+    - USB: serial: ch341: fix lost character on LCR updates
+    - USB: serial: ch341: fix disabled rx timer on older devices
+    - Linux 5.15.66
+  * Jammy update: v5.15.65 upstream stable release (LP: #1991831)
+    - mm: Force TLB flush for PFNMAP mappings before unlink_file_vma()
+    - drm/bridge: Add stubs for devm_drm_of_get_bridge when OF is disabled
+    - ACPI: thermal: drop an always true check
+    - drm/vc4: hdmi: Rework power up
+    - drm/vc4: hdmi: Depends on CONFIG_PM
+    - firmware: tegra: bpmp: Do only aligned access to IPC memory area
+    - crypto: lib - remove unneeded selection of XOR_BLOCKS
+    - Drivers: hv: balloon: Support status report for larger page sizes
+    - mm/hugetlb: avoid corrupting page->mapping in hugetlb_mcopy_atomic_pte
+    - [Config] updateconfigs for ARM64_ERRATUM_2441009
+    - arm64: errata: Add Cortex-A510 to the repeat tlbi list
+    - io_uring: Remove unused function req_ref_put
+    - kbuild: Fix include path in scripts/Makefile.modpost
+    - Bluetooth: L2CAP: Fix build errors in some archs
+    - HID: steam: Prevent NULL pointer dereference in steam_{recv,send}_report
+    - udmabuf: Set the DMA mask for the udmabuf device (v2)
+    - media: pvrusb2: fix memory leak in pvr_probe
+    - HID: hidraw: fix memory leak in hidraw_release()
+    - net: fix refcount bug in sk_psock_get (2)
+    - fbdev: fb_pm2fb: Avoid potential divide by zero error
+    - ftrace: Fix NULL pointer dereference in is_ftrace_trampoline when ftrace is
+      dead
+    - bpf: Don't redirect packets with invalid pkt_len
+    - ALSA: usb-audio: Add quirk for LH Labs Geek Out HD Audio 1V5
+    - HID: add Lenovo Yoga C630 battery quirk
+    - HID: AMD_SFH: Add a DMI quirk entry for Chromebooks
+    - HID: asus: ROG NKey: Ignore portion of 0x5a report
+    - HID: thrustmaster: Add sparco wheel and fix array length
+    - drm/i915/gt: Skip TLB invalidations once wedged
+    - mmc: mtk-sd: Clear interrupts when cqe off/disable
+    - mmc: sdhci-of-dwcmshc: add reset call back for rockchip Socs
+    - mmc: sdhci-of-dwcmshc: rename rk3568 to rk35xx
+    - mmc: sdhci-of-dwcmshc: Re-enable support for the BlueField-3 SoC
+    - btrfs: remove root argument from btrfs_unlink_inode()
+    - btrfs: remove no longer needed logic for replaying directory deletes
+    - btrfs: add and use helper for unlinking inode during log replay
+    - btrfs: fix warning during log replay when bumping inode link count
+    - fs/ntfs3: Fix work with fragmented xattr
+    - ASoC: sh: rz-ssi: Improve error handling in rz_ssi_probe() error path
+    - drm/amd/display: Avoid MPC infinite loop
+    - drm/amd/display: Fix HDMI VSIF V3 incorrect issue
+    - drm/amd/display: For stereo keep "FLIP_ANY_FRAME"
+    - drm/amd/display: clear optc underflow before turn off odm clock
+    - ksmbd: return STATUS_BAD_NETWORK_NAME error status if share is not
+      configured
+    - neigh: fix possible DoS due to net iface start/stop loop
+    - s390/hypfs: avoid error message under KVM
+    - ksmbd: don't remove dos attribute xattr on O_TRUNC open
+    - drm/amd/pm: add missing ->fini_microcode interface for Sienna Cichlid
+    - drm/amd/display: Fix pixel clock programming
+    - drm/amdgpu: Increase tlb flush timeout for sriov
+    - drm/amd/display: avoid doing vm_init multiple time
+    - netfilter: conntrack: NF_CONNTRACK_PROCFS should no longer default to y
+    - testing: selftests: nft_flowtable.sh: use random netns names
+    - btrfs: move lockdep class helpers to locking.c
+    - btrfs: fix lockdep splat with reloc root extent buffers
+    - btrfs: tree-checker: check for overlapping extent items
+    - kprobes: don't call disarm_kprobe() for disabled kprobes
+    - btrfs: fix space cache corruption and potential double allocations
+    - android: binder: fix lockdep check on clearing vma
+    - net/af_packet: check len when min_header_len equals to 0
+    - net: neigh: don't call kfree_skb() under spin_lock_irqsave()
+    - Linux 5.15.65
+  * CVE-2022-2663
+    - netfilter: nf_conntrack_irc: Fix forged IP logic
+  * CVE-2022-3061
+    - video: fbdev: i740fb: Error out if 'pixclock' equals zero
+
+  [ Ubuntu: 5.15.0-56.62 ]
+
+  * jammy/linux: 5.15.0-56.62 -proposed tracker (LP: #1997079)
+  * CVE-2022-3566
+    - tcp: Fix data races around icsk->icsk_af_ops.
+  * CVE-2022-3567
+    - ipv6: annotate some data-races around sk->sk_prot
+    - ipv6: Fix data races around sk->sk_prot.
+  * CVE-2022-3621
+    - nilfs2: fix NULL pointer dereference at nilfs_bmap_lookup_at_level()
+  * CVE-2022-3564
+    - Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
+  * CVE-2022-3524
+    - tcp/udp: Fix memory leak in ipv6_renew_options().
+  * CVE-2022-3565
+    - mISDN: fix use-after-free bugs in l1oip timer handlers
+  * CVE-2022-3594
+    - r8152: Rate limit overflow messages
+  * CVE-2022-43945
+    - SUNRPC: Fix svcxdr_init_decode's end-of-buffer calculation
+    - SUNRPC: Fix svcxdr_init_encode's buflen calculation
+    - NFSD: Protect against send buffer overflow in NFSv2 READDIR
+    - NFSD: Protect against send buffer overflow in NFSv3 READDIR
+    - NFSD: Protect against send buffer overflow in NFSv2 READ
+    - NFSD: Protect against send buffer overflow in NFSv3 READ
+    - NFSD: Remove "inline" directives on op_rsize_bop helpers
+    - NFSD: Cap rsize_bop result based on send buffer size
+  * CVE-2022-42703
+    - mm/rmap: Fix anon_vma->degree ambiguity leading to double-reuse
+  * 5.15.0-53-generic no longer boots (LP: #1996740)
+    - drm/amd/display: Add helper for blanking all dp displays
+
+  [ Ubuntu: 5.15.0-53.59 ]
+
+  * Fix blank screen on Thinkpad ADL 4K+ panel (LP: #1980621)
+    - drm/i915: Implement WaEdpLinkRateDataReload
+  * Kernel regresses openjdk on riscv64 (LP: #1992484)
+    - SAUCE: Revert "riscv: mmap with PROT_WRITE but no PROT_READ is invalid"
+  * iavf: SR-IOV VFs error with no traffic flow when MTU greater than 1500
+    (LP: #1983656)
+    - iavf: Fix set max MTU size with port VLAN and jumbo frames
+    - i40e: Fix VF set max MTU size
+  * [Ubuntu 22.04] mpt3sas: Request to include latest bug fix patches
+    (LP: #1965927)
+    - scsi: mpt3sas: Remove scsi_dma_map() error messages
+    - scsi: mpt3sas: Update persistent trigger pages from sysfs interface
+  * ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel
+    systems (LP: #1990985)
+    - ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel
+      systems
+  * Fix resume on AMD platforms when TBT monitor is plugged (LP: #1990920)
+    - SAUCE: Revert "drm/amd/display: Add helper for blanking all dp displays"
+    - drm/amd/display: Detect dpcd_rev when hotplug mst monitor
+    - drm/amd/display: Release remote dc_sink under mst scenario
+  * LSM: Configuring Too Many LSMs Causes Kernel Panic on Boot (LP: #1987998)
+    - SAUCE: LSM: Change Landlock from LSMBLOB_NEEDED to LSMBLOB_NOT_NEEDED
+  * To support Intel Maple Ridge Thunderbolt [8086:1134] (LP: #1990240)
+    - thunderbolt: Add support for Intel Maple Ridge single port controller
+  * Intel graphic driver is not probing[8086:468b] (LP: #1990242)
+    - drm/i915/adl_s: Update ADL-S PCI IDs
+    - drm/i915: Add new ADL-S pci id
+  * Add HDMI codec ID for Intel Raptor Lake (LP: #1989578)
+    - ALSA: hda: Add PCI and HDMI IDs for Intel Raptor Lake
+  * Jammy update: v5.15.64 upstream stable release (LP: #1991717)
+    - wifi: rtlwifi: remove always-true condition pointed out by GCC 12
+    - eth: sun: cassini: remove dead code
+    - audit: fix potential double free on error path from fsnotify_add_inode_mark
+    - cgroup: Fix race condition at rebind_subsystems()
+    - parisc: Make CONFIG_64BIT available for ARCH=parisc64 only
+    - parisc: Fix exception handler for fldw and fstw instructions
+    - kernel/sys_ni: add compat entry for fadvise64_64
+    - x86/entry: Move CLD to the start of the idtentry macro
+    - block: add a bdev_max_zone_append_sectors helper
+    - block: add bdev_max_segments() helper
+    - btrfs: zoned: revive max_zone_append_bytes
+    - btrfs: replace BTRFS_MAX_EXTENT_SIZE with fs_info->max_extent_size
+    - btrfs: convert count_max_extents() to use fs_info->max_extent_size
+    - Input: i8042 - move __initconst to fix code styling warning
+    - Input: i8042 - merge quirk tables
+    - Input: i8042 - add TUXEDO devices to i8042 quirk tables
+    - Input: i8042 - add additional TUXEDO devices to i8042 quirk tables
+    - drivers/base: fix userspace break from using bin_attributes for cpumap and
+      cpulist
+    - scsi: qla2xxx: Fix response queue handler reading stale packets
+    - scsi: qla2xxx: edif: Fix dropped IKE message
+    - btrfs: put initial index value of a directory in a constant
+    - btrfs: pass the dentry to btrfs_log_new_name() instead of the inode
+    - btrfs: remove unnecessary parameter delalloc_start for writepage_delalloc()
+    - riscv: lib: uaccess: fold fixups into body
+    - riscv: lib: uaccess: fix CSR_STATUS SR_SUM bit
+    - xfrm: fix refcount leak in __xfrm_policy_check()
+    - xfrm: clone missing x->lastused in xfrm_do_migrate
+    - xfrm: policy: fix metadata dst->dev xmit null pointer dereference
+    - fs: require CAP_SYS_ADMIN in target namespace for idmapped mounts
+    - net: use eth_hw_addr_set() instead of ether_addr_copy()
+    - Revert "net: macsec: update SCI upon MAC address change."
+    - NFS: Don't allocate nfs_fattr on the stack in __nfs42_ssc_open()
+    - NFSv4.2 fix problems with __nfs42_ssc_open
+    - SUNRPC: RPC level errors should set task->tk_rpc_status
+    - mm/smaps: don't access young/dirty bit if pte unpresent
+    - ntfs: fix acl handling
+    - rose: check NULL rose_loopback_neigh->loopback
+    - r8152: fix the units of some registers for RTL8156A
+    - r8152: fix the RX FIFO settings when suspending
+    - nfc: pn533: Fix use-after-free bugs caused by pn532_cmd_timeout
+    - ice: xsk: Force rings to be sized to power of 2
+    - ice: xsk: prohibit usage of non-balanced queue id
+    - net/mlx5e: Properly disable vlan strip on non-UL reps
+    - net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
+    - net/mlx5e: Fix wrong application of the LRO state
+    - net/mlx5e: Fix wrong tc flag used when set hw-tc-offload off
+    - net: ipa: don't assume SMEM is page-aligned
+    - net: phy: Don't WARN for PHY_READY state in mdio_bus_phy_resume()
+    - net: moxa: get rid of asymmetry in DMA mapping/unmapping
+    - bonding: 802.3ad: fix no transmission of LACPDUs
+    - net: ipvtap - add __init/__exit annotations to module init/exit funcs
+    - netfilter: ebtables: reject blobs that don't provide all entry points
+    - bnxt_en: fix NQ resource accounting during vf creation on 57500 chips
+    - netfilter: nf_tables: disallow updates of implicit chain
+    - netfilter: nf_tables: make table handle allocation per-netns friendly
+    - netfilter: nft_payload: report ERANGE for too long offset and length
+    - netfilter: nft_payload: do not truncate csum_offset and csum_type
+    - netfilter: nf_tables: do not leave chain stats enabled on error
+    - netfilter: nft_osf: restrict osf to ipv4, ipv6 and inet families
+    - netfilter: nft_tunnel: restrict it to netdev family
+    - netfilter: nf_tables: consolidate rule verdict trace call
+    - netfilter: nft_cmp: optimize comparison for 16-bytes
+    - netfilter: bitwise: improve error goto labels
+    - netfilter: nf_tables: upfront validation of data via nft_data_init()
+    - netfilter: nf_tables: disallow jump to implicit chain from set element
+    - netfilter: nf_tables: disallow binding to already bound chain
+    - netfilter: flowtable: add function to invoke garbage collection immediately
+    - netfilter: flowtable: fix stuck flows on cleanup due to pending work
+    - net: Fix data-races around sysctl_[rw]mem_(max|default).
+    - net: Fix data-races around weight_p and dev_weight_[rt]x_bias.
+    - net: Fix data-races around netdev_max_backlog.
+    - net: Fix data-races around netdev_tstamp_prequeue.
+    - ratelimit: Fix data-races in ___ratelimit().
+    - net: Fix data-races around sysctl_optmem_max.
+    - net: Fix a data-race around sysctl_tstamp_allow_data.
+    - net: Fix a data-race around sysctl_net_busy_poll.
+    - net: Fix a data-race around sysctl_net_busy_read.
+    - net: Fix a data-race around netdev_budget.
+    - tcp: expose the tcp_mark_push() and tcp_skb_entail() helpers
+    - mptcp: stop relying on tcp_tx_skb_cache
+    - net: Fix data-races around sysctl_max_skb_frags.
+    - net: Fix a data-race around netdev_budget_usecs.
+    - net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
+    - net: Fix data-races around sysctl_devconf_inherit_init_net.
+    - net: Fix a data-race around sysctl_somaxconn.
+    - ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
+    - i40e: Fix incorrect address type for IPv6 flow rules
+    - rxrpc: Fix locking in rxrpc's sendmsg
+    - ionic: widen queue_lock use around lif init and deinit
+    - ionic: clear broken state on generation change
+    - ionic: fix up issues with handling EAGAIN on FW cmds
+    - ionic: VF initial random MAC address if no assigned mac
+    - net: stmmac: work around sporadic tx issue on link-up
+    - btrfs: fix silent failure when deleting root reference
+    - btrfs: replace: drop assert for suspended replace
+    - btrfs: add info when mount fails due to stale replace target
+    - btrfs: check if root is readonly while setting security xattr
+    - btrfs: fix possible memory leak in btrfs_get_dev_args_from_path()
+    - perf/x86/lbr: Enable the branch type for the Arch LBR by default
+    - x86/unwind/orc: Unwind ftrace trampolines with correct ORC entry
+    - x86/bugs: Add "unknown" reporting for MMIO Stale Data
+    - x86/nospec: Unwreck the RSB stuffing
+    - loop: Check for overflow while configuring loop
+    - writeback: avoid use-after-free after removing device
+    - asm-generic: sections: refactor memory_intersects
+    - mm/damon/dbgfs: avoid duplicate context directory creation
+    - s390/mm: do not trigger write fault when vma does not allow VM_WRITE
+    - bootmem: remove the vmemmap pages from kmemleak in put_page_bootmem
+    - s390: fix double free of GS and RI CBs on fork() failure
+    - fbdev: fbcon: Properly revert changes when vc_resize() failed
+    - Revert "memcg: cleanup racy sum avoidance code"
+    - ACPI: processor: Remove freq Qos request for all CPUs
+    - nouveau: explicitly wait on the fence in nouveau_bo_move_m2mf
+    - smb3: missing inode locks in punch hole
+    - xen/privcmd: fix error exit of privcmd_ioctl_dm_op()
+    - riscv: traps: add missing prototype
+    - io_uring: fix issue with io_write() not always undoing sb_start_write()
+    - mm/hugetlb: fix hugetlb not supporting softdirty tracking
+    - md: call __md_stop_writes in md_stop
+    - mptcp: Fix crash due to tcp_tsorted_anchor was initialized before release
+      skb
+    - arm64: Fix match_list for erratum 1286807 on Arm Cortex-A76
+    - binder_alloc: add missing mmap_lock calls when using the VMA
+    - x86/nospec: Fix i386 RSB stuffing
+    - Documentation/ABI: Mention retbleed vulnerability info file for sysfs
+    - blk-mq: fix io hung due to missing commit_rqs
+    - perf python: Fix build when PYTHON_CONFIG is user supplied
+    - perf/x86/intel/uncore: Fix broken read_counter() for SNB IMC PMU
+    - perf/x86/intel/ds: Fix precise store latency handling
+    - perf stat: Clear evsel->reset_group for each stat run
+    - scsi: ufs: core: Enable link lost interrupt
+    - scsi: storvsc: Remove WQ_MEM_RECLAIM from storvsc_error_wq
+    - bpf: Don't use tnum_range on array range checking for poke descriptors
+    - Linux 5.15.64
+  * Jammy update: v5.15.63 upstream stable release (LP: #1990564)
+    - ALSA: info: Fix llseek return value when using callback
+    - ALSA: hda/realtek: Add quirk for Clevo NS50PU, NS70PU
+    - KVM: Unconditionally get a ref to /dev/kvm module when creating a VM
+    - x86/mm: Use proper mask when setting PUD mapping
+    - rds: add missing barrier to release_refill
+    - locking/atomic: Make test_and_*_bit() ordered on failure
+    - drm/nouveau: recognise GA103
+    - drm/ttm: Fix dummy res NULL ptr deref bug
+    - drm/amd/display: Check correct bounds for stream encoder instances for
+      DCN303
+    - ata: libata-eh: Add missing command name
+    - mmc: pxamci: Fix another error handling path in pxamci_probe()
+    - mmc: pxamci: Fix an error handling path in pxamci_probe()
+    - mmc: meson-gx: Fix an error handling path in meson_mmc_probe()
+    - btrfs: unset reloc control if transaction commit fails in
+      prepare_to_relocate()
+    - btrfs: reset RO counter on block group if we fail to relocate
+    - btrfs: fix lost error handling when looking up extended ref on log replay
+    - cifs: Fix memory leak on the deferred close
+    - x86/kprobes: Fix JNG/JNLE emulation
+    - tracing/eprobes: Do not allow eprobes to use $stack, or % for regs
+    - tracing/eprobes: Do not hardcode $comm as a string
+    - tracing/eprobes: Have event probes be consistent with kprobes and uprobes
+    - tracing/probes: Have kprobes and uprobes use $COMM too
+    - tracing: Have filter accept "common_cpu" to be consistent
+    - ALSA: usb-audio: More comprehensive mixer map for ASUS ROG Zenith II
+    - dt-bindings: usb: mtk-xhci: Allow wakeup interrupt-names to be optional
+    - can: ems_usb: fix clang's -Wunaligned-access warning
+    - apparmor: fix quiet_denied for file rules
+    - Revert "UBUNTU: SAUCE: apparmor: drop prefixing abs root labels with '='"
+    - apparmor: fix absroot causing audited secids to begin with =
+    - apparmor: Fix failed mount permission check error message
+    - apparmor: fix aa_label_asxprint return check
+    - apparmor: fix setting unconfined mode on a loaded profile
+    - apparmor: fix overlapping attachment computation
+    - apparmor: fix reference count leak in aa_pivotroot()
+    - apparmor: Fix memleak in aa_simple_write_to_buffer()
+    - Documentation: ACPI: EINJ: Fix obsolete example
+    - NFSv4.1: Don't decrease the value of seq_nr_highest_sent
+    - NFSv4.1: Handle NFS4ERR_DELAY replies to OP_SEQUENCE correctly
+    - NFSv4: Fix races in the legacy idmapper upcall
+    - NFSv4.1: RECLAIM_COMPLETE must handle EACCES
+    - NFSv4/pnfs: Fix a use-after-free bug in open
+    - BPF: Fix potential bad pointer dereference in bpf_sys_bpf()
+    - bpf: Don't reinit map value in prealloc_lru_pop
+    - bpf: Acquire map uref in .init_seq_private for array map iterator
+    - bpf: Acquire map uref in .init_seq_private for hash map iterator
+    - bpf: Acquire map uref in .init_seq_private for sock local storage map
+      iterator
+    - bpf: Acquire map uref in .init_seq_private for sock{map,hash} iterator
+    - bpf: Check the validity of max_rdwr_access for sock local storage map
+      iterator
+    - can: mcp251x: Fix race condition on receive interrupt
+    - can: j1939: j1939_session_destroy(): fix memory leak of skbs
+    - net: atlantic: fix aq_vec index out of range error
+    - m68k: coldfire/device.c: protect FLEXCAN blocks
+    - sunrpc: fix expiry of auth creds
+    - SUNRPC: Fix xdr_encode_bool()
+    - SUNRPC: Reinitialise the backchannel request buffers before reuse
+    - virtio_net: fix memory leak inside XPD_TX with mergeable
+    - devlink: Fix use-after-free after a failed reload
+    - net: phy: Warn about incorrect mdio_bus_phy_resume() state
+    - net: bcmgenet: Indicate MAC is in charge of PHY PM
+    - net: bgmac: Fix a BUG triggered by wrong bytes_compl
+    - selftests: forwarding: Fix failing tests with old libnet
+    - dt-bindings: arm: qcom: fix Alcatel OneTouch Idol 3 compatibles
+    - pinctrl: nomadik: Fix refcount leak in nmk_pinctrl_dt_subnode_to_map
+    - pinctrl: qcom: msm8916: Allow CAMSS GP clocks to be muxed
+    - pinctrl: amd: Don't save/restore interrupt status and wake status bits
+    - pinctrl: sunxi: Add I/O bias setting for H6 R-PIO
+    - pinctrl: qcom: sm8250: Fix PDC map
+    - Input: exc3000 - fix return value check of wait_for_completion_timeout
+    - octeontx2-pf: Fix NIX_AF_TL3_TL2X_LINKX_CFG register configuration
+    - octeontx2-af: Apply tx nibble fixup always
+    - octeontx2-af: suppress external profile loading warning
+    - octeontx2-af: Fix mcam entry resource leak
+    - octeontx2-af: Fix key checking for source mac
+    - ACPI: property: Return type of acpi_add_nondev_subnodes() should be bool
+    - geneve: do not use RT_TOS for IPv6 flowlabel
+    - mlx5: do not use RT_TOS for IPv6 flowlabel
+    - ipv6: do not use RT_TOS for IPv6 flowlabel
+    - plip: avoid rcu debug splat
+    - vsock: Fix memory leak in vsock_connect()
+    - vsock: Set socket state back to SS_UNCONNECTED in vsock_connect_timeout()
+    - dt-bindings: gpio: zynq: Add missing compatible strings
+    - dt-bindings: arm: qcom: fix Longcheer L8150 compatibles
+    - dt-bindings: arm: qcom: fix MSM8916 MTP compatibles
+    - dt-bindings: arm: qcom: fix MSM8994 boards compatibles
+    - dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
+    - spi: dt-bindings: cadence: add missing 'required'
+    - spi: dt-bindings: zynqmp-qspi: add missing 'required'
+    - ceph: use correct index when encoding client supported features
+    - tools/vm/slabinfo: use alphabetic order when two values are equal
+    - ceph: don't leak snap_rwsem in handle_cap_grant
+    - kbuild: dummy-tools: avoid tmpdir leak in dummy gcc
+    - tools build: Switch to new openssl API for test-libcrypto
+    - NTB: ntb_tool: uninitialized heap data in tool_fn_write()
+    - nfp: ethtool: fix the display error of `ethtool -m DEVNAME`
+    - xen/xenbus: fix return type in xenbus_file_read()
+    - atm: idt77252: fix use-after-free bugs caused by tst_timer
+    - geneve: fix TOS inheriting for ipv4
+    - perf probe: Fix an error handling path in 'parse_perf_probe_command()'
+    - perf parse-events: Fix segfault when event parser gets an error
+    - perf tests: Fix Track with sched_switch test for hybrid case
+    - dpaa2-eth: trace the allocated address instead of page struct
+    - fs/ntfs3: Fix using uninitialized value n when calling indx_read
+    - fs/ntfs3: Fix NULL deref in ntfs_update_mftmirr
+    - fs/ntfs3: Don't clear upper bits accidentally in log_replay()
+    - fs/ntfs3: Fix double free on remount
+    - fs/ntfs3: Do not change mode if ntfs_set_ea failed
+    - fs/ntfs3: Fix missing i_op in ntfs_read_mft
+    - nios2: page fault et.al. are *not* restartable syscalls...
+    - nios2: don't leave NULLs in sys_call_table[]
+    - nios2: traced syscall does need to check the syscall number
+    - nios2: fix syscall restart checks
+    - nios2: restarts apply only to the first sigframe we build...
+    - nios2: add force_successful_syscall_return()
+    - iavf: Fix adminq error handling
+    - iavf: Fix reset error handling
+    - ASoC: SOF: debug: Fix potential buffer overflow by snprintf()
+    - ASoC: tas2770: Set correct FSYNC polarity
+    - ASoC: tas2770: Allow mono streams
+    - ASoC: tas2770: Drop conflicting set_bias_level power setting
+    - ASoC: tas2770: Fix handling of mute/unmute
+    - ASoC: codec: tlv320aic32x4: fix mono playback via I2S
+    - netfilter: nf_tables: use READ_ONCE and WRITE_ONCE for shared generation id
+      access
+    - fs/ntfs3: uninitialized variable in ntfs_set_acl_ex()
+    - netfilter: nf_tables: disallow NFTA_SET_ELEM_KEY_END with
+      NFT_SET_ELEM_INTERVAL_END flag
+    - netfilter: nf_tables: possible module reference underflow in error path
+    - netfilter: nf_tables: really skip inactive sets when allocating name
+    - netfilter: nf_tables: validate NFTA_SET_ELEM_OBJREF based on NFT_SET_OBJECT
+      flag
+    - netfilter: nf_tables: NFTA_SET_ELEM_KEY_END requires concat and interval
+      flags
+    - netfilter: nf_tables: disallow NFT_SET_ELEM_CATCHALL and
+      NFT_SET_ELEM_INTERVAL_END
+    - netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified
+    - powerpc/pci: Fix get_phb_number() locking
+    - spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
+    - net/sunrpc: fix potential memory leaks in rpc_sysfs_xprt_state_change()
+    - net: dsa: mv88e6060: prevent crash on an unused port
+    - mlxsw: spectrum: Clear PTP configuration after unregistering the netdevice
+    - net: moxa: pass pdev instead of ndev to DMA functions
+    - net: fix potential refcount leak in ndisc_router_discovery()
+    - net: dsa: microchip: ksz9477: fix fdb_dump last invalid entry
+    - net: dsa: felix: fix ethtool 256-511 and 512-1023 TX packet counters
+    - net: genl: fix error path memory leak in policy dumping
+    - net: dsa: don't warn in dsa_port_set_state_now() when driver doesn't support
+      it
+    - net: dsa: sja1105: fix buffer overflow in sja1105_setup_devlink_regions()
+    - ice: Ignore EEXIST when setting promisc mode
+    - i2c: imx: Make sure to unregister adapter on remove()
+    - regulator: pca9450: Remove restrictions for regulator-name
+    - i40e: Fix to stop tx_timeout recovery if GLOBR fails
+    - fec: Fix timer capture timing in `fec_ptp_enable_pps()`
+    - stmmac: intel: Add a missing clk_disable_unprepare() call in
+      intel_eth_pci_remove()
+    - igb: Add lock to avoid data race
+    - kbuild: fix the modules order between drivers and libs
+    - gcc-plugins: Undefine LATENT_ENTROPY_PLUGIN when plugin disabled for a file
+    - tracing/eprobes: Fix reading of string fields
+    - drm/imx/dcss: get rid of HPD warning message
+    - ASoC: SOF: Intel: hda: Define rom_status_reg in sof_intel_dsp_desc
+    - ASoC: SOF: Intel: hda: Fix potential buffer overflow by snprintf()
+    - drm/meson: Fix refcount bugs in meson_vpu_has_available_connectors()
+    - drm/sun4i: dsi: Prevent underflow when computing packet sizes
+    - net: qrtr: start MHI channel after endpoit creation
+    - KVM: arm64: Treat PMCR_EL1.LC as RES1 on asymmetric systems
+    - KVM: arm64: Reject 32bit user PSTATE on asymmetric systems
+    - HID: multitouch: new device class fix Lenovo X12 trackpad sticky
+    - PCI: Add ACS quirk for Broadcom BCM5750x NICs
+    - platform/chrome: cros_ec_proto: don't show MKBP version if unsupported
+    - usb: cdns3 fix use-after-free at workaround 2
+    - usb: cdns3: fix random warning message when driver load
+    - usb: gadget: uvc: calculate the number of request depending on framesize
+    - usb: gadget: uvc: call uvc uvcg_warn on completed status instead of
+      uvcg_info
+    - PCI: aardvark: Fix reporting Slot capabilities on emulated bridge
+    - irqchip/tegra: Fix overflow implicit truncation warnings
+    - drm/meson: Fix overflow implicit truncation warnings
+    - clk: ti: Stop using legacy clkctrl names for omap4 and 5
+    - scsi: ufs: ufs-mediatek: Fix the timing of configuring device regulators
+    - usb: host: ohci-ppc-of: Fix refcount leak bug
+    - usb: renesas: Fix refcount leak bug
+    - usb: dwc2: gadget: remove D+ pull-up while no vbus with usb-role-switch
+    - vboxguest: Do not use devm for irq
+    - clk: qcom: ipq8074: dont disable gcc_sleep_clk_src
+    - uacce: Handle parent device removal or parent driver module rmmod
+    - zram: do not lookup algorithm in backends table
+    - clk: qcom: clk-alpha-pll: fix clk_trion_pll_configure description
+    - scsi: lpfc: Prevent buffer overflow crashes in debugfs with malformed user
+      input
+    - scsi: lpfc: Fix possible memory leak when failing to issue CMF WQE
+    - gadgetfs: ep_io - wait until IRQ finishes
+    - coresight: etm4x: avoid build failure with unrolled loops
+    - habanalabs/gaudi: fix shift out of bounds
+    - habanalabs/gaudi: mask constant value before cast
+    - mmc: tmio: avoid glitches when resetting
+    - pinctrl: intel: Check against matching data instead of ACPI companion
+    - cxl: Fix a memory leak in an error handling path
+    - PCI/ACPI: Guard ARM64-specific mcfg_quirks
+    - um: add "noreboot" command line option for PANIC_TIMEOUT=-1 setups
+    - dmaengine: dw-axi-dmac: do not print NULL LLI during error
+    - dmaengine: dw-axi-dmac: ignore interrupt if no descriptor
+    - RDMA/rxe: Limit the number of calls to each tasklet
+    - csky/kprobe: reclaim insn_slot on kprobe unregistration
+    - selftests/kprobe: Do not test for GRP/ without event failures
+    - dmaengine: sprd: Cleanup in .remove() after pm_runtime_get_sync() failed
+    - openrisc: io: Define iounmap argument as volatile
+    - phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks
+    - md: Notify sysfs sync_completed in md_reap_sync_thread()
+    - nvmet-tcp: fix lockdep complaint on nvmet_tcp_wq flush during queue teardown
+    - drivers:md:fix a potential use-after-free bug
+    - ext4: avoid remove directory when directory is corrupted
+    - ext4: avoid resizing to a partial cluster size
+    - lib/list_debug.c: Detect uninitialized lists
+    - tty: serial: Fix refcount leak bug in ucc_uart.c
+    - KVM: PPC: Book3S HV: Fix "rm_exit" entry in debugfs timings
+    - vfio: Clear the caps->buf to NULL after free
+    - mips: cavium-octeon: Fix missing of_node_put() in octeon2_usb_clocks_start
+    - iommu/io-pgtable-arm-v7s: Add a quirk to allow pgtable PA up to 35bit
+    - modules: Ensure natural alignment for .altinstructions and __bug_table
+      sections
+    - ASoC: rsnd: care default case on rsnd_ssiu_busif_err_irq_ctrl()
+    - riscv: dts: sifive: Add fu740 topology information
+    - riscv: dts: canaan: Add k210 topology information
+    - riscv: mmap with PROT_WRITE but no PROT_READ is invalid
+    - RISC-V: Add fast call path of crash_kexec()
+    - watchdog: export lockup_detector_reconfigure
+    - powerpc/32: Set an IBAT covering up to _einittext during init
+    - powerpc/32: Don't always pass -mcpu=powerpc to the compiler
+    - ovl: warn if trusted xattr creation fails
+    - powerpc/ioda/iommu/debugfs: Generate unique debugfs entries
+    - ALSA: core: Add async signal helpers
+    - ALSA: timer: Use deferred fasync helper
+    - ALSA: control: Use deferred fasync helper
+    - f2fs: fix to avoid use f2fs_bug_on() in f2fs_new_node_page()
+    - f2fs: fix to do sanity check on segment type in build_sit_entries()
+    - smb3: check xattr value length earlier
+    - powerpc/64: Init jump labels before parse_early_param()
+    - venus: pm_helpers: Fix warning in OPP during probe
+    - video: fbdev: i740fb: Check the argument of i740_calc_vclk()
+    - MIPS: tlbex: Explicitly compare _PAGE_NO_EXEC against 0
+    - can: j1939: j1939_sk_queue_activate_next_locked(): replace WARN_ON_ONCE with
+      netdev_warn_once()
+    - scsi: ufs: ufs-mediatek: Fix build error and type mismatch
+    - xfs: flush inodegc workqueue tasks before cancel
+    - xfs: reserve quota for dir expansion when linking/unlinking files
+    - xfs: reserve quota for target dir expansion when renaming files
+    - xfs: remove infinite loop when reserving free block pool
+    - xfs: always succeed at setting the reserve pool size
+    - xfs: fix overfilling of reserve pool
+    - xfs: fix soft lockup via spinning in filestream ag selection loop
+    - xfs: revert "xfs: actually bump warning counts when we send warnings"
+    - xfs: reject crazy array sizes being fed to XFS_IOC_GETBMAP*
+    - Linux 5.15.63
+  * Jammy update: v5.15.62 upstream stable release (LP: #1990554)
+    - io_uring: use original request task for inflight tracking
+    - tee: add overflow check in register_shm_helper()
+    - net_sched: cls_route: disallow handle of 0
+    - ksmbd: prevent out of bound read for SMB2_WRITE
+    - ksmbd: fix heap-based overflow in set_ntacl_dacl()
+    - btrfs: only write the sectors in the vertical stripe which has data stripes
+    - btrfs: raid56: don't trust any cached sector in __raid56_parity_recover()
+    - Linux 5.15.62
+  * Jammy update: v5.15.61 upstream stable release (LP: #1990162)
+    - Makefile: link with -z noexecstack --no-warn-rwx-segments
+    - x86: link vdso and boot with -z noexecstack --no-warn-rwx-segments
+    - Revert "pNFS: nfs3_set_ds_client should set NFS_CS_NOPING"
+    - scsi: Revert "scsi: qla2xxx: Fix disk failure to rediscover"
+    - pNFS/flexfiles: Report RDMA connection errors to the server
+    - NFSD: Clean up the show_nf_flags() macro
+    - nfsd: eliminate the NFSD_FILE_BREAK_* flags
+    - ALSA: usb-audio: Add quirk for Behringer UMC202HD
+    - ALSA: bcd2000: Fix a UAF bug on the error path of probing
+    - ALSA: hda/realtek: Add quirk for Clevo NV45PZ
+    - ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
+    - wifi: mac80211_hwsim: fix race condition in pending packet
+    - wifi: mac80211_hwsim: add back erroneously removed cast
+    - wifi: mac80211_hwsim: use 32-bit skb cookie
+    - add barriers to buffer_uptodate and set_buffer_uptodate
+    - lockd: detect and reject lock arguments that overflow
+    - HID: hid-input: add Surface Go battery quirk
+    - HID: wacom: Only report rotation for art pen
+    - HID: wacom: Don't register pad_input for touch switch
+    - KVM: nVMX: Snapshot pre-VM-Enter BNDCFGS for !nested_run_pending case
+    - KVM: nVMX: Snapshot pre-VM-Enter DEBUGCTL for !nested_run_pending case
+    - KVM: SVM: Don't BUG if userspace injects an interrupt with GIF=0
+    - KVM: s390: pv: don't present the ecall interrupt twice
+    - KVM: x86: Split kvm_is_valid_cr4() and export only the non-vendor bits
+    - KVM: nVMX: Let userspace set nVMX MSR to any _host_ supported value
+    - KVM: nVMX: Account for KVM reserved CR4 bits in consistency checks
+    - KVM: nVMX: Inject #UD if VMXON is attempted with incompatible CR0/CR4
+    - KVM: x86: Mark TSS busy during LTR emulation _after_ all fault checks
+    - KVM: x86: Set error code to segment selector on LLDT/LTR non-canonical #GP
+    - KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
+    - KVM: x86: Tag kvm_mmu_x86_module_init() with __init
+    - KVM: x86: do not report preemption if the steal time cache is stale
+    - KVM: x86: revalidate steal time cache if MSR value changes
+    - riscv: set default pm_power_off to NULL
+    - ALSA: hda/conexant: Add quirk for LENOVO 20149 Notebook model
+    - ALSA: hda/cirrus - support for iMac 12,1 model
+    - ALSA: hda/realtek: Add quirk for another Asus K42JZ model
+    - ALSA: hda/realtek: Add a quirk for HP OMEN 15 (8786) mute LED
+    - tty: vt: initialize unicode screen buffer
+    - vfs: Check the truncate maximum size in inode_newsize_ok()
+    - fs: Add missing umask strip in vfs_tmpfile
+    - thermal: sysfs: Fix cooling_device_stats_setup() error code path
+    - fbcon: Fix boundary checks for fbcon=vc:n1-n2 parameters
+    - fbcon: Fix accelerated fbdev scrolling while logo is still shown
+    - usbnet: Fix linkwatch use-after-free on disconnect
+    - fix short copy handling in copy_mc_pipe_to_iter()
+    - crypto: ccp - Use kzalloc for sev ioctl interfaces to prevent kernel memory
+      leak
+    - ovl: drop WARN_ON() dentry is NULL in ovl_encode_fh()
+    - parisc: Fix device names in /proc/iomem
+    - parisc: Drop pa_swapper_pg_lock spinlock
+    - parisc: Check the return value of ioremap() in lba_driver_probe()
+    - parisc: io_pgetevents_time64() needs compat syscall in 32-bit compat mode
+    - riscv:uprobe fix SR_SPIE set/clear handling
+    - dt-bindings: riscv: fix SiFive l2-cache's cache-sets
+    - RISC-V: kexec: Fixup use of smp_processor_id() in preemptible context
+    - RISC-V: Fixup get incorrect user mode PC for kernel mode regs
+    - RISC-V: Fixup schedule out issue in machine_crash_shutdown()
+    - RISC-V: Add modules to virtual kernel memory layout dump
+    - rtc: rx8025: fix 12/24 hour mode detection on RX-8035
+    - drm/gem: Properly annotate WW context on drm_gem_lock_reservations() error
+    - drm/shmem-helper: Add missing vunmap on error
+    - drm/vc4: hdmi: Disable audio if dmas property is present but empty
+    - drm/hyperv-drm: Include framebuffer and EDID headers
+    - drm/nouveau: fix another off-by-one in nvbios_addr
+    - drm/nouveau: Don't pm_runtime_put_sync(), only pm_runtime_put_autosuspend()
+    - drm/nouveau/acpi: Don't print error when we get -EINPROGRESS from pm_runtime
+    - drm/nouveau/kms: Fix failure path for creating DP connectors
+    - drm/amdgpu: Check BO's requested pinning domains against its
+      preferred_domains
+    - bpf: Fix KASAN use-after-free Read in compute_effective_progs
+    - btrfs: reject log replay if there is unsupported RO compat flag
+    - mtd: rawnand: arasan: Fix clock rate in NV-DDR
+    - mtd: rawnand: arasan: Update NAND bus clock instead of system clock
+    - um: Remove straying parenthesis
+    - um: seed rng using host OS rng
+    - iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
+    - iio: light: isl29028: Fix the warning in isl29028_remove()
+    - scsi: sg: Allow waiting for commands to complete on removed device
+    - scsi: qla2xxx: Fix incorrect display of max frame size
+    - scsi: qla2xxx: Zero undefined mailbox IN registers
+    - soundwire: qcom: Check device status before reading devid
+    - ksmbd: fix memory leak in smb2_handle_negotiate
+    - ksmbd: prevent out of bound read for SMB2_TREE_CONNNECT
+    - ksmbd: fix use-after-free bug in smb2_tree_disconect
+    - fuse: limit nsec
+    - fuse: ioctl: translate ENOSYS
+    - serial: mvebu-uart: uart2 error bits clearing
+    - md-raid10: fix KASAN warning
+    - mbcache: don't reclaim used entries
+    - mbcache: add functions to delete entry if unused
+    - media: [PATCH] pci: atomisp_cmd: fix three missing checks on list iterator
+    - ia64, processor: fix -Wincompatible-pointer-types in ia64_get_irr()
+    - PCI: Add defines for normal and subtractive PCI bridges
+    - powerpc/fsl-pci: Fix Class Code of PCIe Root Port
+    - powerpc/ptdump: Fix display of RW pages on FSL_BOOK3E
+    - powerpc/powernv: Avoid crashing if rng is NULL
+    - MIPS: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+    - coresight: Clear the connection field properly
+    - usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
+    - USB: HCD: Fix URB giveback issue in tasklet function
+    - ARM: dts: uniphier: Fix USB interrupts for PXs2 SoC
+    - arm64: dts: uniphier: Fix USB interrupts for PXs3 SoC
+    - usb: dwc3: gadget: refactor dwc3_repare_one_trb
+    - usb: dwc3: gadget: fix high speed multiplier setting
+    - netfilter: nf_tables: fix null deref due to zeroed list head
+    - epoll: autoremove wakers even more aggressively
+    - x86: Handle idle=nomwait cmdline properly for x86_idle
+    - arch: make TRACE_IRQFLAGS_NMI_SUPPORT generic
+    - arm64: Do not forget syscall when starting a new thread.
+    - arm64: fix oops in concurrently setting insn_emulation sysctls
+    - ext2: Add more validity checks for inode counts
+    - sched/fair: Introduce SIS_UTIL to search idle CPU based on sum of util_avg
+    - genirq: Don't return error on missing optional irq_request_resources()
+    - irqchip/mips-gic: Only register IPI domain when SMP is enabled
+    - genirq: GENERIC_IRQ_IPI depends on SMP
+    - sched/core: Always flush pending blk_plug
+    - irqchip/mips-gic: Check the return value of ioremap() in gic_of_init()
+    - wait: Fix __wait_event_hrtimeout for RT/DL tasks
+    - ARM: dts: imx6ul: add missing properties for sram
+    - ARM: dts: imx6ul: change operating-points to uint32-matrix
+    - ARM: dts: imx6ul: fix keypad compatible
+    - ARM: dts: imx6ul: fix csi node compatible
+    - ARM: dts: imx6ul: fix lcdif node compatible
+    - ARM: dts: imx6ul: fix qspi node compatible
+    - ARM: dts: BCM5301X: Add DT for Meraki MR26
+    - ARM: dts: ux500: Fix Codina accelerometer mounting matrix
+    - ARM: dts: ux500: Fix Gavini accelerometer mounting matrix
+    - spi: synquacer: Add missing clk_disable_unprepare()
+    - ARM: OMAP2+: display: Fix refcount leak bug
+    - ARM: OMAP2+: pdata-quirks: Fix refcount leak bug
+    - ACPI: EC: Remove duplicate ThinkPad X1 Carbon 6th entry from DMI quirks
+    - ACPI: EC: Drop the EC_FLAGS_IGNORE_DSDT_GPE quirk
+    - ACPI: PM: save NVS memory for Lenovo G40-45
+    - ACPI: LPSS: Fix missing check in register_device_clock()
+    - ARM: dts: qcom: sdx55: Fix the IRQ trigger type for UART
+    - arm64: dts: qcom: ipq8074: fix NAND node name
+    - arm64: dts: allwinner: a64: orangepi-win: Fix LED node name
+    - ARM: shmobile: rcar-gen2: Increase refcount for new reference
+    - firmware: tegra: Fix error check return value of debugfs_create_file()
+    - hwmon: (dell-smm) Add Dell XPS 13 7390 to fan control whitelist
+    - hwmon: (sht15) Fix wrong assumptions in device remove callback
+    - PM: hibernate: defer device probing when resuming from hibernation
+    - selinux: fix memleak in security_read_state_kernel()
+    - selinux: Add boundary check in put_entry()
+    - kasan: test: Silence GCC 12 warnings
+    - drm/amdgpu: Remove one duplicated ef removal
+    - powerpc/64s: Disable stack variable initialisation for prom_init
+    - spi: spi-rspi: Fix PIO fallback on RZ platforms
+    - ARM: findbit: fix overflowing offset
+    - meson-mx-socinfo: Fix refcount leak in meson_mx_socinfo_init
+    - arm64: dts: renesas: beacon: Fix regulator node names
+    - spi: spi-altera-dfl: Fix an error handling path
+    - ARM: bcm: Fix refcount leak in bcm_kona_smc_init
+    - ACPI: processor/idle: Annotate more functions to live in cpuidle section
+    - ARM: dts: imx7d-colibri-emmc: add cpu1 supply
+    - soc: renesas: r8a779a0-sysc: Fix A2DP1 and A2CV[2357] PDR values
+    - scsi: hisi_sas: Use managed PCI functions
+    - dt-bindings: iio: accel: Add DT binding doc for ADXL355
+    - soc: amlogic: Fix refcount leak in meson-secure-pwrc.c
+    - arm64: dts: renesas: Fix thermal-sensors on single-zone sensors
+    - x86/pmem: Fix platform-device leak in error path
+    - ARM: dts: ast2500-evb: fix board compatible
+    - ARM: dts: ast2600-evb: fix board compatible
+    - ARM: dts: ast2600-evb-a1: fix board compatible
+    - arm64: dts: mt8192: Fix idle-states nodes naming scheme
+    - arm64: dts: mt8192: Fix idle-states entry-method
+    - arm64: select TRACE_IRQFLAGS_NMI_SUPPORT
+    - arm64: cpufeature: Allow different PMU versions in ID_DFR0_EL1
+    - locking/lockdep: Fix lockdep_init_map_*() confusion
+    - arm64: dts: qcom: sc7180: Remove ipa_fw_mem node on trogdor
+    - soc: fsl: guts: machine variable might be unset
+    - block: fix infinite loop for invalid zone append
+    - ARM: dts: qcom: mdm9615: add missing PMIC GPIO reg
+    - ARM: OMAP2+: Fix refcount leak in omapdss_init_of
+    - ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
+    - arm64: dts: qcom: sdm630: disable GPU by default
+    - arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
+    - arm64: dts: qcom: sdm630: fix gpu's interconnect path
+    - arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf
+    - cpufreq: zynq: Fix refcount leak in zynq_get_revision
+    - regulator: qcom_smd: Fix pm8916_pldo range
+    - ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP
+    - ARM: dts: qcom-msm8974: fix irq type on blsp2_uart1
+    - soc: qcom: ocmem: Fix refcount leak in of_get_ocmem
+    - soc: qcom: aoss: Fix refcount leak in qmp_cooling_devices_register
+    - ARM: dts: qcom: pm8841: add required thermal-sensor-cells
+    - bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
+    - stack: Declare {randomize_,}kstack_offset to fix Sparse warnings
+    - arm64: dts: qcom: msm8916: Fix typo in pronto remoteproc node
+    - ACPI: APEI: explicit init of HEST and GHES in apci_init()
+    - drivers/iio: Remove all strcpy() uses
+    - ACPI: VIOT: Fix ACS setup
+    - arm64: dts: qcom: sm6125: Move sdc2 pinctrl from seine-pdx201 to sm6125
+    - arm64: dts: qcom: sm6125: Append -state suffix to pinctrl nodes
+    - arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
+    - arm64: dts: mt7622: fix BPI-R64 WPS button
+    - arm64: tegra: Fixup SYSRAM references
+    - arm64: tegra: Update Tegra234 BPMP channel addresses
+    - arm64: tegra: Mark BPMP channels as no-memory-wc
+    - arm64: tegra: Fix SDMMC1 CD on P2888
+    - erofs: avoid consecutive detection for Highmem memory
+    - blk-mq: don't create hctx debugfs dir until q->debugfs_dir is created
+    - spi: Fix simplification of devm_spi_register_controller
+    - spi: tegra20-slink: fix UAF in tegra_slink_remove()
+    - hwmon: (drivetemp) Add module alias
+    - blktrace: Trace remapped requests correctly
+    - PM: domains: Ensure genpd_debugfs_dir exists before remove
+    - dm writecache: return void from functions
+    - dm writecache: count number of blocks read, not number of read bios
+    - dm writecache: count number of blocks written, not number of write bios
+    - dm writecache: count number of blocks discarded, not number of discard bios
+    - regulator: of: Fix refcount leak bug in of_get_regulation_constraints()
+    - soc: qcom: Make QCOM_RPMPD depend on PM
+    - arm64: dts: qcom: qcs404: Fix incorrect USB2 PHYs assignment
+    - irqdomain: Report irq number for NOMAP domains
+    - drivers/perf: arm_spe: Fix consistency of SYS_PMSCR_EL1.CX
+    - nohz/full, sched/rt: Fix missed tick-reenabling bug in dequeue_task_rt()
+    - x86/extable: Fix ex_handler_msr() print condition
+    - selftests/seccomp: Fix compile warning when CC=clang
+    - thermal/tools/tmon: Include pthread and time headers in tmon.h
+    - dm: return early from dm_pr_call() if DM device is suspended
+    - pwm: sifive: Simplify offset calculation for PWMCMP registers
+    - pwm: sifive: Ensure the clk is enabled exactly once per running PWM
+    - pwm: sifive: Shut down hardware only after pwmchip_remove() completed
+    - pwm: lpc18xx-sct: Reduce number of devm memory allocations
+    - pwm: lpc18xx-sct: Simplify driver by not using pwm_[gs]et_chip_data()
+    - pwm: lpc18xx: Fix period handling
+    - drm/dp: Export symbol / kerneldoc fixes for DP AUX bus
+    - drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated
+      function
+    - ath10k: do not enforce interrupt trigger type
+    - drm/st7735r: Fix module autoloading for Okaya RH128128T
+    - drm/panel: Fix build error when CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y &&
+      CONFIG_DRM_DISPLAY_HELPER=m
+    - wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
+    - ath11k: fix netdev open race
+    - drm/mipi-dbi: align max_chunk to 2 in spi_transfer
+    - ath11k: Fix incorrect debug_mask mappings
+    - drm/radeon: fix potential buffer overflow in ni_set_mc_special_registers()
+    - drm/mediatek: Modify dsi funcs to atomic operations
+    - drm/mediatek: Separate poweron/poweroff from enable/disable and define new
+      funcs
+    - drm/mediatek: Add pull-down MIPI operation in mtk_dsi_poweroff function
+    - drm/meson: encoder_hdmi: switch to bridge DRM_BRIDGE_ATTACH_NO_CONNECTOR
+    - drm/meson: encoder_hdmi: Fix refcount leak in meson_encoder_hdmi_init
+    - drm/bridge: lt9611uxc: Cancel only driver's work
+    - i2c: npcm: Remove own slave addresses 2:10
+    - i2c: npcm: Correct slave role behavior
+    - i2c: mxs: Silence a clang warning
+    - virtio-gpu: fix a missing check to avoid NULL dereference
+    - drm/shmem-helper: Unexport drm_gem_shmem_create_with_handle()
+    - drm/shmem-helper: Export dedicated wrappers for GEM object functions
+    - drm/shmem-helper: Pass GEM shmem object in public interfaces
+    - drm/virtio: Fix NULL vs IS_ERR checking in virtio_gpu_object_shmem_init
+    - drm: adv7511: override i2c address of cec before accessing it
+    - crypto: sun8i-ss - do not allocate memory when handling hash requests
+    - crypto: sun8i-ss - fix error codes in allocate_flows()
+    - net: fix sk_wmem_schedule() and sk_rmem_schedule() errors
+    - can: netlink: allow configuring of fixed bit rates without need for
+      do_set_bittiming callback
+    - can: netlink: allow configuring of fixed data bit rates without need for
+      do_set_data_bittiming callback
+    - i2c: Fix a potential use after free
+    - crypto: sun8i-ss - fix infinite loop in sun8i_ss_setup_ivs()
+    - media: atmel: atmel-sama7g5-isc: fix warning in configs without OF
+    - media: tw686x: Register the irq at the end of probe
+    - media: imx-jpeg: Correct some definition according specification
+    - media: imx-jpeg: Leave a blank space before the configuration data
+    - media: imx-jpeg: Add pm-runtime support for imx-jpeg
+    - media: imx-jpeg: use NV12M to represent non contiguous NV12
+    - media: imx-jpeg: Set V4L2_BUF_FLAG_LAST at eos
+    - media: imx-jpeg: Refactor function mxc_jpeg_parse
+    - media: imx-jpeg: Identify and handle precision correctly
+    - media: imx-jpeg: Handle source change in a function
+    - media: imx-jpeg: Support dynamic resolution change
+    - media: imx-jpeg: Align upwards buffer size
+    - media: imx-jpeg: Implement drain using v4l2-mem2mem helpers
+    - wifi: iwlegacy: 4965: fix potential off-by-one overflow in
+      il4965_rs_fill_link_cmd()
+    - drm/radeon: fix incorrrect SPDX-License-Identifiers
+    - rcutorture: Warn on individual rcu_torture_init() error conditions
+    - rcutorture: Don't cpuhp_remove_state() if cpuhp_setup_state() failed
+    - rcutorture: Fix ksoftirqd boosting timing and iteration
+    - test_bpf: fix incorrect netdev features
+    - crypto: ccp - During shutdown, check SEV data pointer before using
+    - drm: bridge: adv7511: Add check for mipi_dsi_driver_register
+    - media: imx-jpeg: Disable slot interrupt when frame done
+    - drm/mcde: Fix refcount leak in mcde_dsi_bind
+    - media: hdpvr: fix error value returns in hdpvr_read
+    - media: v4l2-mem2mem: prevent pollerr when last_buffer_dequeued is set
+    - media: driver/nxp/imx-jpeg: fix a unexpected return value problem
+    - media: tw686x: Fix memory leak in tw686x_video_init
+    - drm/vc4: plane: Remove subpixel positioning check
+    - drm/vc4: plane: Fix margin calculations for the right/bottom edges
+    - drm/bridge: Add a function to abstract away panels
+    - drm/vc4: dsi: Switch to devm_drm_of_get_bridge
+    - drm/vc4: Use of_device_get_match_data()
+    - drm/vc4: dsi: Release workaround buffer and DMA
+    - drm/vc4: dsi: Correct DSI divider calculations
+    - drm/vc4: dsi: Correct pixel order for DSI0
+    - drm/vc4: dsi: Register dsi0 as the correct vc4 encoder type
+    - drm/vc4: dsi: Fix dsi0 interrupt support
+    - drm/vc4: dsi: Add correct stop condition to vc4_dsi_encoder_disable
+      iteration
+    - drm/vc4: hdmi: Fix HPD GPIO detection
+    - drm/vc4: hdmi: Avoid full hdmi audio fifo writes
+    - drm/vc4: hdmi: Reset HDMI MISC_CONTROL register
+    - drm/vc4: hdmi: Fix timings for interlaced modes
+    - drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes
+    - crypto: arm64/gcm - Select AEAD for GHASH_ARM64_CE
+    - selftests/xsk: Destroy BPF resources only when ctx refcount drops to 0
+    - drm/rockchip: vop: Don't crash for invalid duplicate_state()
+    - drm/rockchip: Fix an error handling path rockchip_dp_probe()
+    - drm/mediatek: dpi: Remove output format of YUV
+    - drm/mediatek: dpi: Only enable dpi after the bridge is enabled
+    - drm: bridge: sii8620: fix possible off-by-one
+    - hinic: Use the bitmap API when applicable
+    - net: hinic: fix bug that ethtool get wrong stats
+    - net: hinic: avoid kernel hung in hinic_get_stats64()
+    - drm/msm/mdp5: Fix global state lock backoff
+    - crypto: hisilicon/sec - don't sleep when in softirq
+    - crypto: hisilicon - Kunpeng916 crypto driver don't sleep when in softirq
+    - media: platform: mtk-mdp: Fix mdp_ipi_comm structure alignment
+    - drm/msm: Avoid dirtyfb stalls on video mode displays (v2)
+    - drm/msm/dpu: Fix for non-visible planes
+    - mt76: mt76x02u: fix possible memory leak in __mt76x02u_mcu_send_msg
+    - mt76: mt7615: do not update pm stats in case of error
+    - ieee80211: add EHT 1K aggregation definitions
+    - mt76: mt7921: fix aggregation subframes setting to HE max
+    - mt76: mt7921: enlarge maximum VHT MPDU length to 11454
+    - mediatek: mt76: mac80211: Fix missing of_node_put() in mt76_led_init()
+    - mediatek: mt76: eeprom: fix missing of_node_put() in
+      mt76_find_power_limits_node()
+    - skmsg: Fix invalid last sg check in sk_msg_recvmsg()
+    - drm/exynos/exynos7_drm_decon: free resources when clk_set_parent() failed.
+    - tcp: make retransmitted SKB fit into the send window
+    - libbpf: Fix the name of a reused map
+    - selftests: timers: valid-adjtimex: build fix for newer toolchains
+    - selftests: timers: clocksource-switch: fix passing errors from child
+    - bpf: Fix subprog names in stack traces.
+    - fs: check FMODE_LSEEK to control internal pipe splicing
+    - media: cedrus: h265: Fix flag name
+    - media: hantro: postproc: Fix motion vector space size
+    - media: hantro: Simplify postprocessor
+    - media: hevc: Embedded indexes in RPS
+    - media: staging: media: hantro: Fix typos
+    - wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()
+    - wifi: p54: Fix an error handling path in p54spi_probe()
+    - wifi: p54: add missing parentheses in p54_flush()
+    - selftests/bpf: fix a test for snprintf() overflow
+    - libbpf: fix an snprintf() overflow check
+    - can: pch_can: do not report txerr and rxerr during bus-off
+    - can: rcar_can: do not report txerr and rxerr during bus-off
+    - can: sja1000: do not report txerr and rxerr during bus-off
+    - can: hi311x: do not report txerr and rxerr during bus-off
+    - can: sun4i_can: do not report txerr and rxerr during bus-off
+    - can: kvaser_usb_hydra: do not report txerr and rxerr during bus-off
+    - can: kvaser_usb_leaf: do not report txerr and rxerr during bus-off
+    - can: usb_8dev: do not report txerr and rxerr during bus-off
+    - can: error: specify the values of data[5..7] of CAN error frames
+    - can: pch_can: pch_can_error(): initialize errc before using it
+    - Bluetooth: hci_intel: Add check for platform_driver_register
+    - i2c: cadence: Support PEC for SMBus block read
+    - i2c: mux-gpmux: Add of_node_put() when breaking out of loop
+    - wifi: wil6210: debugfs: fix uninitialized variable use in
+      `wil_write_file_wmi()`
+    - wifi: iwlwifi: mvm: fix double list_add at iwl_mvm_mac_wake_tx_queue
+    - wifi: libertas: Fix possible refcount leak in if_usb_probe()
+    - media: cedrus: hevc: Add check for invalid timestamp
+    - net/mlx5e: Remove WARN_ON when trying to offload an unsupported TLS
+      cipher/version
+    - net/mlx5e: Fix the value of MLX5E_MAX_RQ_NUM_MTTS
+    - net/mlx5: Adjust log_max_qp to be 18 at most
+    - crypto: hisilicon/hpre - don't use GFP_KERNEL to alloc mem during softirq
+    - crypto: inside-secure - Add missing MODULE_DEVICE_TABLE for of
+    - crypto: hisilicon/sec - fix auth key size error
+    - inet: add READ_ONCE(sk->sk_bound_dev_if) in INET_MATCH()
+    - ipv6: add READ_ONCE(sk->sk_bound_dev_if) in INET6_MATCH()
+    - net: allow unbound socket for packets in VRF when tcp_l3mdev_accept set
+    - netdevsim: fib: Fix reference count leak on route deletion failure
+    - wifi: rtw88: check the return value of alloc_workqueue()
+    - iavf: Fix max_rate limiting
+    - iavf: Fix 'tc qdisc show' listing too many queues
+    - netdevsim: Avoid allocation warnings triggered from user space
+    - net: rose: fix netdev reference changes
+    - net: ionic: fix error check for vlan flags in ionic_set_nic_features()
+    - dccp: put dccp_qpolicy_full() and dccp_qpolicy_push() in the same lock
+    - net: usb: make USB_RTL8153_ECM non user configurable
+    - wireguard: ratelimiter: use hrtimer in selftest
+    - wireguard: allowedips: don't corrupt stack when detecting overflow
+    - HID: amd_sfh: Don't show client init failed as error when discovery fails
+    - clk: renesas: r9a06g032: Fix UART clkgrp bitsel
+    - mtd: maps: Fix refcount leak in of_flash_probe_versatile
+    - mtd: maps: Fix refcount leak in ap_flash_init
+    - mtd: rawnand: meson: Fix a potential double free issue
+    - of: check previous kernel's ima-kexec-buffer against memory bounds
+    - scsi: qla2xxx: edif: Reduce Initiator-Initiator thrashing
+    - scsi: qla2xxx: edif: Fix potential stuck session in sa update
+    - scsi: qla2xxx: edif: Reduce connection thrash
+    - scsi: qla2xxx: edif: Fix inconsistent check of db_flags
+    - scsi: qla2xxx: edif: Synchronize NPIV deletion with authentication
+      application
+    - scsi: qla2xxx: edif: Add retry for ELS passthrough
+    - scsi: qla2xxx: edif: Fix n2n discovery issue with secure target
+    - scsi: qla2xxx: edif: Fix n2n login retry for secure device
+    - KVM: SVM: Unwind "speculative" RIP advancement if INTn injection "fails"
+    - KVM: SVM: Stuff next_rip on emulated INT3 injection if NRIPS is supported
+    - phy: samsung: exynosautov9-ufs: correct TSRV register configurations
+    - PCI: microchip: Fix refcount leak in mc_pcie_init_irq_domains()
+    - PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
+    - HID: cp2112: prevent a buffer overflow in cp2112_xfer()
+    - mtd: sm_ftl: Fix deadlock caused by cancel_work_sync in sm_release
+    - mtd: partitions: Fix refcount leak in parse_redboot_of
+    - mtd: parsers: ofpart: Fix refcount leak in bcm4908_partitions_fw_offset
+    - mtd: st_spi_fsm: Add a clk_disable_unprepare() in .probe()'s error path
+    - PCI: mediatek-gen3: Fix refcount leak in mtk_pcie_init_irq_domains()
+    - fpga: altera-pr-ip: fix unsigned comparison with less than zero
+    - usb: host: Fix refcount leak in ehci_hcd_ppc_of_probe
+    - usb: ohci-nxp: Fix refcount leak in ohci_hcd_nxp_probe
+    - usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()
+    - usb: xhci: tegra: Fix error check
+    - netfilter: xtables: Bring SPDX identifier back
+    - scsi: qla2xxx: edif: Send LOGO for unexpected IKE message
+    - scsi: qla2xxx: edif: Reduce disruption due to multiple app start
+    - scsi: qla2xxx: edif: Fix no login after app start
+    - scsi: qla2xxx: edif: Tear down session if keys have been removed
+    - scsi: qla2xxx: edif: Fix session thrash
+    - scsi: qla2xxx: edif: Fix no logout on delete for N2N
+    - iio: accel: bma400: Fix the scale min and max macro values
+    - platform/chrome: cros_ec: Always expose last resume result
+    - iio: accel: bma400: Reordering of header files
+    - clk: mediatek: reset: Fix written reset bit offset
+    - lib/test_hmm: avoid accessing uninitialized pages
+    - memremap: remove support for external pgmap refcounts
+    - mm/memremap: fix memunmap_pages() race with get_dev_pagemap()
+    - KVM: Don't set Accessed/Dirty bits for ZERO_PAGE
+    - mwifiex: Ignore BTCOEX events from the 88W8897 firmware
+    - mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv
+    - scsi: iscsi: Allow iscsi_if_stop_conn() to be called from kernel
+    - scsi: iscsi: Add helper to remove a session from the kernel
+    - scsi: iscsi: Fix session removal on shutdown
+    - dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics
+    - mtd: dataflash: Add SPI ID table
+    - clk: qcom: camcc-sm8250: Fix halt on boot by reducing driver's init level
+    - misc: rtsx: Fix an error handling path in rtsx_pci_probe()
+    - driver core: fix potential deadlock in __driver_attach
+    - clk: qcom: clk-krait: unlock spin after mux completion
+    - clk: qcom: gcc-msm8939: Add missing SYSTEM_MM_NOC_BFDCD_CLK_SRC
+    - clk: qcom: gcc-msm8939: Fix bimc_ddr_clk_src rcgr base address
+    - clk: qcom: gcc-msm8939: Add missing system_mm_noc_bfdcd_clk_src
+    - clk: qcom: gcc-msm8939: Point MM peripherals to system_mm_noc clock
+    - usb: host: xhci: use snprintf() in xhci_decode_trb()
+    - RDMA/rxe: Fix deadlock in rxe_do_local_ops()
+    - clk: qcom: ipq8074: fix NSS core PLL-s
+    - clk: qcom: ipq8074: SW workaround for UBI32 PLL lock
+    - clk: qcom: ipq8074: fix NSS port frequency tables
+    - clk: qcom: ipq8074: set BRANCH_HALT_DELAY flag for UBI clocks
+    - clk: qcom: camcc-sdm845: Fix topology around titan_top power domain
+    - clk: qcom: camcc-sm8250: Fix topology around titan_top power domain
+    - clk: qcom: clk-rcg2: Fail Duty-Cycle configuration if MND divider is not
+      enabled.
+    - clk: qcom: clk-rcg2: Make sure to not write d=0 to the NMD register
+    - mm/mempolicy: fix get_nodes out of bound access
+    - PCI: dwc: Stop link on host_init errors and de-initialization
+    - PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
+    - PCI: dwc: Disable outbound windows only for controllers using iATU
+    - PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
+    - PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
+    - PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
+    - soundwire: bus_type: fix remove and shutdown support
+    - soundwire: revisit driver bind/unbind and callbacks
+    - KVM: arm64: Don't return from void function
+    - dmaengine: sf-pdma: Add multithread support for a DMA channel
+    - PCI: endpoint: Don't stop controller when unbinding endpoint function
+    - scsi: qla2xxx: Check correct variable in qla24xx_async_gffid()
+    - intel_th: Fix a resource leak in an error handling path
+    - intel_th: msu-sink: Potential dereference of null pointer
+    - intel_th: msu: Fix vmalloced buffers
+    - binder: fix redefinition of seq_file attributes
+    - staging: rtl8192u: Fix sleep in atomic context bug in
+      dm_fsync_timer_callback
+    - mmc: sdhci-of-esdhc: Fix refcount leak in esdhc_signal_voltage_switch
+    - mmc: mxcmmc: Silence a clang warning
+    - mmc: renesas_sdhi: Get the reset handle early in the probe
+    - memstick/ms_block: Fix some incorrect memory allocation
+    - memstick/ms_block: Fix a memory leak
+    - mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
+    - of: device: Fix missing of_node_put() in of_dma_set_restricted_buffer
+    - mmc: block: Add single read for 4k sector cards
+    - KVM: s390: pv: leak the topmost page table when destroy fails
+    - PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
+    - scsi: smartpqi: Fix DMA direction for RAID requests
+    - xtensa: iss/network: provide release() callback
+    - xtensa: iss: fix handling error cases in iss_net_configure()
+    - usb: gadget: udc: amd5536 depends on HAS_DMA
+    - usb: aspeed-vhub: Fix refcount leak bug in ast_vhub_init_desc()
+    - usb: dwc3: core: Deprecate GCTL.CORESOFTRESET
+    - usb: dwc3: core: Do not perform GCTL_CORE_SOFTRESET during bootup
+    - usb: dwc3: qcom: fix missing optional irq warnings
+    - eeprom: idt_89hpesx: uninitialized data in idt_dbgfs_csr_write()
+    - phy: stm32: fix error return in stm32_usbphyc_phy_init
+    - interconnect: imx: fix max_node_id
+    - um: random: Don't initialise hwrng struct with zero
+    - RDMA/irdma: Fix a window for use-after-free
+    - RDMA/irdma: Fix VLAN connection with wildcard address
+    - RDMA/irdma: Fix setting of QP context err_rq_idx_valid field
+    - RDMA/rtrs-srv: Fix modinfo output for stringify
+    - RDMA/rtrs: Fix warning when use poll mode on client side.
+    - RDMA/rtrs: Replace duplicate check with is_pollqueue helper
+    - RDMA/rtrs: Introduce destroy_cq helper
+    - RDMA/rtrs: Do not allow sessname to contain special symbols / and .
+    - RDMA/rtrs: Rename rtrs_sess to rtrs_path
+    - RDMA/rtrs-srv: Rename rtrs_srv_sess to rtrs_srv_path
+    - RDMA/rtrs-clt: Rename rtrs_clt_sess to rtrs_clt_path
+    - RDMA/rtrs-clt: Replace list_next_or_null_rr_rcu with an inline function
+    - RDMA/qedr: Fix potential memory leak in __qedr_alloc_mr()
+    - RDMA/hns: Fix incorrect clearing of interrupt status register
+    - RDMA/siw: Fix duplicated reported IW_CM_EVENT_CONNECT_REPLY event
+    - iio: cros: Register FIFO callback after sensor is registered
+    - clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
+    - RDMA/hfi1: fix potential memory leak in setup_base_ctxt()
+    - gpio: gpiolib-of: Fix refcount bugs in of_mm_gpiochip_add_data()
+    - HID: mcp2221: prevent a buffer overflow in mcp_smbus_write()
+    - HID: amd_sfh: Add NULL check for hid device
+    - dmaengine: imx-dma: Cast of_device_get_match_data() with (uintptr_t)
+    - scripts/gdb: lx-dmesg: read records individually
+    - scripts/gdb: fix 'lx-dmesg' on 32 bits arch
+    - RDMA/rxe: Fix mw bind to allow any consumer key portion
+    - mmc: cavium-octeon: Add of_node_put() when breaking out of loop
+    - mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
+    - HID: alps: Declare U1_UNICORN_LEGACY support
+    - RDMA/rxe: For invalidate compare according to set keys in mr
+    - PCI: tegra194: Fix Root Port interrupt handling
+    - PCI: tegra194: Fix link up retry sequence
+    - HID: amd_sfh: Handle condition of "no sensors"
+    - USB: serial: fix tty-port initialized comments
+    - usb: cdns3: change place of 'priv_ep' assignment in
+      cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
+    - mtd: spi-nor: fix spi_nor_spimem_setup_op() call in
+      spi_nor_erase_{sector,chip}()
+    - KVM: nVMX: Set UMIP bit CR4_FIXED1 MSR when emulating UMIP
+    - platform/olpc: Fix uninitialized data in debugfs write
+    - RDMA/srpt: Duplicate port name members
+    - RDMA/srpt: Introduce a reference count in struct srpt_device
+    - RDMA/srpt: Fix a use-after-free
+    - android: binder: stop saving a pointer to the VMA
+    - mm/mmap.c: fix missing call to vm_unacct_memory in mmap_region
+    - selftests: kvm: set rax before vmcall
+    - of/fdt: declared return type does not match actual return type
+    - RDMA/mlx5: Add missing check for return value in get namespace flow
+    - RDMA/rxe: Add memory barriers to kernel queues
+    - RDMA/rxe: Remove the is_user members of struct rxe_sq/rxe_rq/rxe_srq
+    - RDMA/rxe: Fix error unwind in rxe_create_qp()
+    - block/rnbd-srv: Set keep_id to true after mutex_trylock
+    - null_blk: fix ida error handling in null_add_dev()
+    - nvme: use command_id instead of req->tag in trace_nvme_complete_rq()
+    - nvme: define compat_ioctl again to unbreak 32-bit userspace.
+    - nvme: disable namespace access for unsupported metadata
+    - nvme: don't return an error from nvme_configure_metadata
+    - nvme: catch -ENODEV from nvme_revalidate_zones again
+    - block/bio: remove duplicate append pages code
+    - block: ensure iov_iter advances for added pages
+    - jbd2: fix outstanding credits assert in jbd2_journal_commit_transaction()
+    - ext4: recover csum seed of tmp_inode after migrating to extents
+    - jbd2: fix assertion 'jh->b_frozen_data == NULL' failure when journal aborted
+    - usb: cdns3: Don't use priv_dev uninitialized in cdns3_gadget_ep_enable()
+    - opp: Fix error check in dev_pm_opp_attach_genpd()
+    - ASoC: cros_ec_codec: Fix refcount leak in cros_ec_codec_platform_probe
+    - ASoC: samsung: Fix error handling in aries_audio_probe
+    - ASoC: imx-audmux: Silence a clang warning
+    - ASoC: mediatek: mt8173: Fix refcount leak in mt8173_rt5650_rt5676_dev_probe
+    - ASoC: mt6797-mt6351: Fix refcount leak in mt6797_mt6351_dev_probe
+    - ASoC: codecs: da7210: add check for i2c_add_driver
+    - ASoC: mediatek: mt8173-rt5650: Fix refcount leak in mt8173_rt5650_dev_probe
+    - serial: 8250: Export ICR access helpers for internal use
+    - serial: 8250: dma: Allow driver operations before starting DMA transfers
+    - serial: 8250_dw: Store LSR into lsr_saved_flags in dw8250_tx_wait_empty()
+    - ASoC: codecs: msm8916-wcd-digital: move gains from SX_TLV to S8_TLV
+    - ASoC: codecs: wcd9335: move gains from SX_TLV to S8_TLV
+    - rpmsg: char: Add mutex protection for rpmsg_eptdev_open()
+    - rpmsg: mtk_rpmsg: Fix circular locking dependency
+    - remoteproc: k3-r5: Fix refcount leak in k3_r5_cluster_of_init
+    - selftests/livepatch: better synchronize test_klp_callbacks_busy
+    - profiling: fix shift too large makes kernel panic
+    - remoteproc: imx_rproc: Fix refcount leak in imx_rproc_addr_init
+    - ASoC: samsung: h1940_uda1380: include proepr GPIO consumer header
+    - powerpc/perf: Optimize clearing the pending PMI and remove WARN_ON for PMI
+      check in power_pmu_disable
+    - ASoC: samsung: change gpiod_speaker_power and rx1950_audio from global to
+      static variables
+    - tty: n_gsm: Delete gsmtty open SABM frame when config requester
+    - tty: n_gsm: fix user open not possible at responder until initiator open
+    - tty: n_gsm: fix tty registration before control channel open
+    - tty: n_gsm: fix wrong queuing behavior in gsm_dlci_data_output()
+    - tty: n_gsm: fix missing timer to handle stalled links
+    - tty: n_gsm: fix non flow control frames during mux flow off
+    - tty: n_gsm: fix packet re-transmission without open control channel
+    - tty: n_gsm: fix race condition in gsmld_write()
+    - tty: n_gsm: fix resource allocation order in gsm_activate_mux()
+    - ASoC: qcom: Fix missing of_node_put() in
+      asoc_qcom_lpass_cpu_platform_probe()
+    - ASoC: imx-card: Fix DSD/PDM mclk frequency
+    - remoteproc: qcom: wcnss: Fix handling of IRQs
+    - vfio/ccw: Do not change FSM state in subchannel event
+    - serial: 8250_fsl: Don't report FE, PE and OE twice
+    - tty: n_gsm: fix wrong T1 retry count handling
+    - tty: n_gsm: fix DM command
+    - tty: n_gsm: fix missing corner cases in gsmld_poll()
+    - MIPS: vdso: Utilize __pa() for gic_pfn
+    - swiotlb: fail map correctly with failed io_tlb_default_mem
+    - ASoC: mt6359: Fix refcount leak bug
+    - serial: 8250_bcm7271: Save/restore RTS in suspend/resume
+    - iommu/exynos: Handle failed IOMMU device registration properly
+    - 9p: fix a bunch of checkpatch warnings
+    - 9p: Drop kref usage
+    - 9p: Add client parameter to p9_req_put()
+    - net: 9p: fix refcount leak in p9_read_work() error handling
+    - MIPS: Fixed __debug_virt_addr_valid()
+    - rpmsg: qcom_smd: Fix refcount leak in qcom_smd_parse_edge
+    - kfifo: fix kfifo_to_user() return type
+    - lib/smp_processor_id: fix imbalanced instrumentation_end() call
+    - proc: fix a dentry lock race between release_task and lookup
+    - remoteproc: qcom: pas: Check if coredump is enabled
+    - remoteproc: sysmon: Wait for SSCTL service to come up
+    - mfd: t7l66xb: Drop platform disable callback
+    - mfd: max77620: Fix refcount leak in max77620_initialise_fps
+    - iommu/arm-smmu: qcom_iommu: Add of_node_put() when breaking out of loop
+    - perf tools: Fix dso_id inode generation comparison
+    - s390/dump: fix old lowcore virtual vs physical address confusion
+    - s390/maccess: fix semantics of memcpy_real() and its callers
+    - s390/crash: fix incorrect number of bytes to copy to user space
+    - s390/zcore: fix race when reading from hardware system area
+    - ASoC: fsl_asrc: force cast the asrc_format type
+    - ASoC: fsl-asoc-card: force cast the asrc_format type
+    - ASoC: fsl_easrc: use snd_pcm_format_t type for sample_format
+    - ASoC: imx-card: use snd_pcm_format_t type for asrc_format
+    - ASoC: qcom: q6dsp: Fix an off-by-one in q6adm_alloc_copp()
+    - fuse: Remove the control interface for virtio-fs
+    - ASoC: audio-graph-card: Add of_node_put() in fail path
+    - watchdog: sp5100_tco: Fix a memory leak of EFCH MMIO resource
+    - watchdog: armada_37xx_wdt: check the return value of devm_ioremap() in
+      armada_37xx_wdt_probe()
+    - video: fbdev: amba-clcd: Fix refcount leak bugs
+    - video: fbdev: sis: fix typos in SiS_GetModeID()
+    - ASoC: mchp-spdifrx: disable end of block interrupt on failures
+    - powerpc/32: Call mmu_mark_initmem_nx() regardless of data block mapping.
+    - powerpc/32: Do not allow selection of e5500 or e6500 CPUs on PPC32
+    - powerpc/iommu: Fix iommu_table_in_use for a small default DMA window case
+    - powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and
+      alias
+    - tty: serial: fsl_lpuart: correct the count of break characters
+    - s390/dump: fix os_info virtual vs physical address confusion
+    - s390/smp: cleanup target CPU callback starting
+    - s390/smp: cleanup control register update routines
+    - s390/maccess: rework absolute lowcore accessors
+    - s390/smp: enforce lowcore protection on CPU restart
+    - f2fs: fix to remove F2FS_COMPR_FL and tag F2FS_NOCOMP_FL at the same time
+    - powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
+    - powerpc/xive: Fix refcount leak in xive_get_max_prio
+    - powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
+    - perf symbol: Fail to read phdr workaround
+    - kprobes: Forbid probing on trampoline and BPF code areas
+    - x86/bus_lock: Don't assume the init value of DEBUGCTLMSR.BUS_LOCK_DETECT to
+      be zero
+    - powerpc/pci: Fix PHB numbering when using opal-phbid
+    - genelf: Use HAVE_LIBCRYPTO_SUPPORT, not the never defined HAVE_LIBCRYPTO
+    - scripts/faddr2line: Fix vmlinux detection on arm64
+    - sched/deadline: Merge dl_task_can_attach() and dl_cpu_busy()
+    - sched, cpuset: Fix dl_cpu_busy() panic due to empty cs->cpus_allowed
+    - x86/numa: Use cpumask_available instead of hardcoded NULL check
+    - video: fbdev: arkfb: Fix a divide-by-zero bug in ark_set_pixclock()
+    - tools/thermal: Fix possible path truncations
+    - sched: Fix the check of nr_running at queue wakelist
+    - sched: Remove the limitation of WF_ON_CPU on wakelist if wakee cpu is idle
+    - sched/core: Do not requeue task on CPU excluded from cpus_mask
+    - f2fs: allow compression for mmap files in compress_mode=user
+    - f2fs: do not allow to decompress files have FI_COMPRESS_RELEASED
+    - video: fbdev: vt8623fb: Check the size of screen before memset_io()
+    - video: fbdev: arkfb: Check the size of screen before memset_io()
+    - video: fbdev: s3fb: Check the size of screen before memset_io()
+    - scsi: ufs: core: Correct ufshcd_shutdown() flow
+    - scsi: zfcp: Fix missing auto port scan and thus missing target ports
+    - scsi: qla2xxx: Fix imbalance vha->vref_count
+    - scsi: qla2xxx: Fix discovery issues in FC-AL topology
+    - scsi: qla2xxx: Turn off multi-queue for 8G adapters
+    - scsi: qla2xxx: Fix crash due to stale SRB access around I/O timeouts
+    - scsi: qla2xxx: Fix excessive I/O error messages by default
+    - scsi: qla2xxx: Fix erroneous mailbox timeout after PCI error injection
+    - scsi: qla2xxx: Wind down adapter after PCIe error
+    - scsi: qla2xxx: Fix losing FCP-2 targets on long port disable with I/Os
+    - scsi: qla2xxx: Fix losing target when it reappears during delete
+    - scsi: qla2xxx: Fix losing FCP-2 targets during port perturbation tests
+    - x86/bugs: Enable STIBP for IBPB mitigated RETBleed
+    - ftrace/x86: Add back ftrace_expected assignment
+    - x86/kprobes: Update kcb status flag after singlestepping
+    - x86/olpc: fix 'logical not is only applied to the left hand side'
+    - SMB3: fix lease break timeout when multiple deferred close handles for the
+      same file.
+    - Input: gscps2 - check return value of ioremap() in gscps2_probe()
+    - __follow_mount_rcu(): verify that mount_lock remains unchanged
+    - spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
+    - drm/mediatek: Allow commands to be sent during video mode
+    - drm/mediatek: Keep dsi as LP00 before dcs cmds transfer
+    - crypto: blake2s - remove shash module
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component
+    - usbnet: smsc95xx: Don't clear read-only PHY interrupt
+    - usbnet: smsc95xx: Avoid link settings race on interrupt reception
+    - firmware: arm_scpi: Ensure scpi_info is not assigned if the probe fails
+    - scsi: lpfc: SLI path split: Refactor lpfc_iocbq
+    - scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
+    - scsi: lpfc: SLI path split: Refactor SCSI paths
+    - scsi: lpfc: Remove extra atomic_inc on cmd_pending in queuecommand after
+      VMID
+    - intel_th: pci: Add Meteor Lake-P support
+    - intel_th: pci: Add Raptor Lake-S PCH support
+    - intel_th: pci: Add Raptor Lake-S CPU support
+    - KVM: set_msr_mce: Permit guests to ignore single-bit ECC errors
+    - KVM: x86: Signal #GP, not -EPERM, on bad WRMSR(MCi_CTL/STATUS)
+    - iommu/vt-d: avoid invalid memory access via node_online(NUMA_NO_NODE)
+    - PCI/AER: Iterate over error counters instead of error strings
+    - PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
+    - serial: 8250_pci: Refactor the loop in pci_ite887x_init()
+    - serial: 8250_pci: Replace dev_*() by pci_*() macros
+    - serial: 8250: Fold EndRun device support into OxSemi Tornado code
+    - serial: 8250: Add proper clock handling for OxSemi PCIe devices
+    - tty: 8250: Add support for Brainboxes PX cards.
+    - dm writecache: set a default MAX_WRITEBACK_JOBS
+    - kexec, KEYS, s390: Make use of built-in and secondary keyring for signature
+      verification
+    - dm thin: fix use-after-free crash in dm_sm_register_threshold_callback
+    - net/9p: Initialize the iounit field during fid creation
+    - ARM: remove some dead code
+    - timekeeping: contribute wall clock to rng on time change
+    - locking/csd_lock: Change csdlock_debug from early_param to __setup
+    - block: remove the struct blk_queue_ctx forward declaration
+    - block: don't allow the same type rq_qos add more than once
+    - btrfs: ensure pages are unlocked on cow_file_range() failure
+    - btrfs: reset block group chunk force if we have to wait
+    - btrfs: properly flag filesystem with BTRFS_FEATURE_INCOMPAT_BIG_METADATA
+    - ACPI: CPPC: Do not prevent CPPC from working in the future
+    - powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
+    - KVM: x86/pmu: Introduce the ctrl_mask value for fixed counter
+    - KVM: VMX: Mark all PERF_GLOBAL_(OVF)_CTRL bits reserved if there's no vPMU
+    - KVM: x86/pmu: Ignore pmu->global_ctrl check if vPMU doesn't support
+      global_ctrl
+    - KVM: VMX: Add helper to check if the guest PMU has PERF_GLOBAL_CTRL
+    - KVM: nVMX: Attempt to load PERF_GLOBAL_CTRL on nVMX xfer iff it exists
+    - dm raid: fix address sanitizer warning in raid_status
+    - dm raid: fix address sanitizer warning in raid_resume
+    - tracing: Add '__rel_loc' using trace event macros
+    - tracing: Avoid -Warray-bounds warning for __rel_loc macro
+    - ext4: update s_overhead_clusters in the superblock during an on-line resize
+    - ext4: fix extent status tree race in writeback error recovery path
+    - ext4: add EXT4_INODE_HAS_XATTR_SPACE macro in xattr.h
+    - ext4: fix use-after-free in ext4_xattr_set_entry
+    - ext4: correct max_inline_xattr_value_size computing
+    - ext4: correct the misjudgment in ext4_iget_extra_inode
+    - ext4: fix warning in ext4_iomap_begin as race between bmap and write
+    - ext4: check if directory block is within i_size
+    - ext4: make sure ext4_append() always allocates new block
+    - ext4: remove EA inode entry from mbcache on inode eviction
+    - ext4: use kmemdup() to replace kmalloc + memcpy
+    - ext4: unindent codeblock in ext4_xattr_block_set()
+    - ext4: fix race when reusing xattr blocks
+    - KEYS: asymmetric: enforce SM2 signature use pkey algo
+    - tpm: eventlog: Fix section mismatch for DEBUG_SECTION_MISMATCH
+    - xen-blkback: fix persistent grants negotiation
+    - xen-blkback: Apply 'feature_persistent' parameter when connect
+    - xen-blkfront: Apply 'feature_persistent' parameter when connect
+    - powerpc: Fix eh field when calling lwarx on PPC32
+    - tracing: Use a struct alignof to determine trace event field alignment
+    - mac80211: fix a memory leak where sta_info is not freed
+    - tcp: fix over estimation in sk_forced_mem_schedule()
+    - crypto: lib/blake2s - reduce stack frame usage in self test
+    - Revert "mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv"
+    - Revert "s390/smp: enforce lowcore protection on CPU restart"
+    - drm/bridge: tc358767: Fix (e)DP bridge endpoint parsing in dedicated
+      function
+    - net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
+    - drm/vc4: change vc4_dma_range_matches from a global to static
+    - tracing/perf: Avoid -Warray-bounds warning for __rel_loc macro
+    - drm/msm: Fix dirtyfb refcounting
+    - drm/meson: Fix refcount leak in meson_encoder_hdmi_init
+    - io_uring: mem-account pbuf buckets
+    - Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm regression
+    - drm/bridge: Move devm_drm_of_get_bridge to bridge/panel.c
+    - scsi: lpfc: Fix locking for lpfc_sli_iocbq_lookup()
+    - scsi: lpfc: Fix element offset in __lpfc_sli_release_iocbq_s4()
+    - scsi: lpfc: Resolve some cleanup issues following SLI path refactoring
+    - Linux 5.15.61
+  * CVE-2022-3028
+    - af_key: Do not call xfrm_probe_algs in parallel
+  * CVE-2022-2978
+    - fs: fix UAF/GPF bug in nilfs_mdt_destroy
+  * CVE-2022-40768
+    - scsi: stex: Properly zero out the passthrough command structure
+
+  [ Ubuntu: 5.15.0-52.58 ]
+
+  * CVE-2022-2602
+    - SAUCE: io_uring/af_unix: defer registered files gc to io_uring release
+    - SAUCE: io_uring/af_unix: fix memleak during unix GC
+  * CVE-2022-41674
+    - mac80211: move CRC into struct ieee802_11_elems
+    - mac80211: mlme: find auth challenge directly
+    - mac80211: mesh: clean up rx_bcn_presp API
+    - mac80211: always allocate struct ieee802_11_elems
+    - mac80211: fix memory leaks with element parsing
+    - SAUCE: wifi: cfg80211: fix u8 overflow in
+      cfg80211_update_notlisted_nontrans()
+    - SAUCE: wifi: cfg80211/mac80211: reject bad MBSSID elements
+    - SAUCE: wifi: cfg80211: ensure length byte is present before access
+    - SAUCE: wifi: mac80211_hwsim: avoid mac80211 warning on bad rate
+    - SAUCE: wifi: cfg80211: update hidden BSSes to avoid WARN_ON
+  * CVE-2022-42722
+    - SAUCE: wifi: mac80211: fix crash in beacon protection for P2P-device
+  * CVE-2022-42721
+    - SAUCE: wifi: cfg80211: avoid nontransmitted BSS list corruption
+  * CVE-2022-42720
+    - SAUCE: wifi: cfg80211: fix BSS refcounting bugs
+  * CVE-2022-42719
+    - SAUCE: wifi: mac80211: fix MBSSID parsing use-after-free
+
+  [ Ubuntu: 5.15.0-50.56 ]
+
+  * jammy/linux: 5.15.0-50.56 -proposed tracker (LP: #1990148)
+  * CVE-2022-3176
+    - io_uring: refactor poll update
+    - io_uring: move common poll bits
+    - io_uring: kill poll linking optimisation
+    - io_uring: inline io_poll_complete
+    - io_uring: correct fill events helpers types
+    - io_uring: clean cqe filling functions
+    - io_uring: poll rework
+    - io_uring: remove poll entry from list when canceling all
+    - io_uring: bump poll refs to full 31-bits
+    - io_uring: fail links when poll fails
+    - io_uring: fix wrong arm_poll error handling
+    - io_uring: fix UAF due to missing POLLFREE handling
+  * ip/nexthop: fix default address selection for connected nexthop
+    (LP: #1988809)
+    - selftests/net: test nexthop without gw
+  * ip/nexthop: fix default address selection for connected nexthop
+    (LP: #1988809) // icmp_redirect.sh in ubuntu_kernel_selftests failed on
+    Jammy 5.15.0-49.55 (LP: #1990124)
+    - ip: fix triggering of 'icmp redirect'
+
+  [ Ubuntu: 5.15.0-49.55 ]
+
+  * jammy/linux: 5.15.0-49.55 -proposed tracker (LP: #1989785)
+  * amdgpu module crash after 5.15 kernel update (LP: #1981883)
+    - drm/amdgpu: fix check in fbdev init
+  * scsi: hisi_sas: Increase debugfs_dump_index after dump is  completed
+    (LP: #1982070)
+    - scsi: hisi_sas: Increase debugfs_dump_index after dump is completed
+  * [UBUNTU 22.04] s390/qeth: cache link_info for ethtool (LP: #1984103)
+    - s390/qeth: cache link_info for ethtool
+  * WARN in trace_event_dyn_put_ref (LP: #1987232)
+    - tracing/perf: Fix double put of trace event when init fails
+  * Jammy update: v5.15.60 upstream stable release (LP: #1989221)
+    - x86/speculation: Make all RETbleed mitigations 64-bit only
+    - selftests/bpf: Extend verifier and bpf_sock tests for dst_port loads
+    - selftests/bpf: Check dst_port only on the client socket
+    - block: fix default IO priority handling again
+    - tools/vm/slabinfo: Handle files in debugfs
+    - ACPI: video: Force backlight native for some TongFang devices
+    - ACPI: video: Shortening quirk list by identifying Clevo by board_name only
+    - ACPI: APEI: Better fix to avoid spamming the console with old error logs
+    - crypto: arm64/poly1305 - fix a read out-of-bound
+    - KVM: x86: do not report a vCPU as preempted outside instruction boundaries
+    - KVM: x86: do not set st->preempted when going back to user space
+    - KVM: selftests: Make hyperv_clock selftest more stable
+    - tools/kvm_stat: fix display of error when multiple processes are found
+    - selftests: KVM: Handle compiler optimizations in ucall
+    - KVM: x86/svm: add __GFP_ACCOUNT to __sev_dbg_{en,de}crypt_user()
+    - arm64: set UXN on swapper page tables
+    - btrfs: zoned: prevent allocation from previous data relocation BG
+    - btrfs: zoned: fix critical section of relocation inode writeback
+    - Bluetooth: hci_bcm: Add BCM4349B1 variant
+    - Bluetooth: hci_bcm: Add DT compatible for CYW55572
+    - dt-bindings: bluetooth: broadcom: Add BCM4349B1 DT binding
+    - Bluetooth: btusb: Add support of IMC Networks PID 0x3568
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04CA:0x4007
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04C5:0x1675
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0CB8:0xC558
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3587
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3586
+    - macintosh/adb: fix oob read in do_adb_query() function
+    - x86/speculation: Add RSB VM Exit protections
+    - x86/speculation: Add LFENCE to RSB fill sequence
+    - Linux 5.15.60
+  * Jammy update: v5.15.59 upstream stable release (LP: #1989218)
+    - Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
+    - Revert "ocfs2: mount shared volume without ha stack"
+    - ntfs: fix use-after-free in ntfs_ucsncmp()
+    - fs: sendfile handles O_NONBLOCK of out_fd
+    - secretmem: fix unhandled fault in truncate
+    - mm: fix page leak with multiple threads mapping the same page
+    - hugetlb: fix memoryleak in hugetlb_mcopy_atomic_pte
+    - asm-generic: remove a broken and needless ifdef conditional
+    - s390/archrandom: prevent CPACF trng invocations in interrupt context
+    - nouveau/svm: Fix to migrate all requested pages
+    - drm/simpledrm: Fix return type of simpledrm_simple_display_pipe_mode_valid()
+    - watch_queue: Fix missing rcu annotation
+    - watch_queue: Fix missing locking in add_watch_to_object()
+    - tcp: Fix data-races around sysctl_tcp_dsack.
+    - tcp: Fix a data-race around sysctl_tcp_app_win.
+    - tcp: Fix a data-race around sysctl_tcp_adv_win_scale.
+    - tcp: Fix a data-race around sysctl_tcp_frto.
+    - tcp: Fix a data-race around sysctl_tcp_nometrics_save.
+    - tcp: Fix data-races around sysctl_tcp_no_ssthresh_metrics_save.
+    - ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
+    - ice: do not setup vlan for loopback VSI
+    - scsi: ufs: host: Hold reference returned by of_parse_phandle()
+    - Revert "tcp: change pingpong threshold to 3"
+    - octeontx2-pf: Fix UDP/TCP src and dst port tc filters
+    - tcp: Fix data-races around sysctl_tcp_moderate_rcvbuf.
+    - tcp: Fix a data-race around sysctl_tcp_limit_output_bytes.
+    - tcp: Fix a data-race around sysctl_tcp_challenge_ack_limit.
+    - scsi: core: Fix warning in scsi_alloc_sgtables()
+    - scsi: mpt3sas: Stop fw fault watchdog work item during system shutdown
+    - net: ping6: Fix memleak in ipv6_renew_options().
+    - ipv6/addrconf: fix a null-ptr-deref bug for ip6_ptr
+    - net/tls: Remove the context from the list in tls_device_down
+    - igmp: Fix data-races around sysctl_igmp_qrv.
+    - net: pcs: xpcs: propagate xpcs_read error to xpcs_get_state_c37_sgmii
+    - net: sungem_phy: Add of_node_put() for reference returned by of_get_parent()
+    - tcp: Fix a data-race around sysctl_tcp_min_tso_segs.
+    - tcp: Fix a data-race around sysctl_tcp_min_rtt_wlen.
+    - tcp: Fix a data-race around sysctl_tcp_autocorking.
+    - tcp: Fix a data-race around sysctl_tcp_invalid_ratelimit.
+    - Documentation: fix sctp_wmem in ip-sysctl.rst
+    - macsec: fix NULL deref in macsec_add_rxsa
+    - macsec: fix error message in macsec_add_rxsa and _txsa
+    - macsec: limit replay window size with XPN
+    - macsec: always read MACSEC_SA_ATTR_PN as a u64
+    - net: macsec: fix potential resource leak in macsec_add_rxsa() and
+      macsec_add_txsa()
+    - net: mld: fix reference count leak in mld_{query | report}_work()
+    - tcp: Fix data-races around sk_pacing_rate.
+    - net: Fix data-races around sysctl_[rw]mem(_offset)?.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_delay_ns.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_slack_ns.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_nr.
+    - tcp: Fix data-races around sysctl_tcp_reflect_tos.
+    - ipv4: Fix data-races around sysctl_fib_notify_on_flag_change.
+    - i40e: Fix interface init with MSI interrupts (no MSI-X)
+    - sctp: fix sleep in atomic context bug in timer handlers
+    - octeontx2-pf: cn10k: Fix egress ratelimit configuration
+    - virtio-net: fix the race between refill work and close
+    - perf symbol: Correct address for bss symbols
+    - sfc: disable softirqs for ptp TX
+    - sctp: leave the err path free in sctp_stream_init to sctp_stream_free
+    - ARM: crypto: comment out gcc warning that breaks clang builds
+    - mm/hmm: fault non-owner device private entries
+    - page_alloc: fix invalid watermark check on a negative value
+    - ARM: 9216/1: Fix MAX_DMA_ADDRESS overflow
+    - EDAC/ghes: Set the DIMM label unconditionally
+    - docs/kernel-parameters: Update descriptions for "mitigations=" param with
+      retbleed
+    - locking/rwsem: Allow slowpath writer to ignore handoff bit if not set by
+      first waiter
+    - x86/bugs: Do not enable IBPB at firmware entry when IBPB is not available
+    - Linux 5.15.59
+  * Jammy update: v5.15.58 upstream stable release (LP: #1988479)
+    - pinctrl: stm32: fix optional IRQ support to gpios
+    - riscv: add as-options for modules with assembly compontents
+    - mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
+    - lockdown: Fix kexec lockdown bypass with ima policy
+    - drm/ttm: fix locking in vmap/vunmap TTM GEM helpers
+    - bus: mhi: host: pci_generic: add Telit FN980 v1 hardware revision
+    - bus: mhi: host: pci_generic: add Telit FN990
+    - Revert "selftest/vm: verify remap destination address in mremap_test"
+    - Revert "selftest/vm: verify mmap addr in mremap_test"
+    - PCI: hv: Fix multi-MSI to allow more than one MSI vector
+    - PCI: hv: Fix hv_arch_irq_unmask() for multi-MSI
+    - PCI: hv: Reuse existing IRTE allocation in compose_msi_msg()
+    - PCI: hv: Fix interrupt mapping for multi-MSI
+    - serial: mvebu-uart: correctly report configured baudrate value
+    - batman-adv: Use netif_rx_any_context() any.
+    - xfs: fix maxlevels comparisons in the btree staging code
+    - xfs: fold perag loop iteration logic into helper function
+    - xfs: rename the next_agno perag iteration variable
+    - xfs: terminate perag iteration reliably on agcount
+    - xfs: fix perag reference leak on iteration race with growfs
+    - xfs: prevent a WARN_ONCE() in xfs_ioc_attr_list()
+    - r8152: fix a WOL issue
+    - ip: Fix data-races around sysctl_ip_default_ttl.
+    - xfrm: xfrm_policy: fix a possible double xfrm_pols_put() in
+      xfrm_bundle_lookup()
+    - power/reset: arm-versatile: Fix refcount leak in versatile_reboot_probe
+    - RDMA/irdma: Do not advertise 1GB page size for x722
+    - RDMA/irdma: Fix sleep from invalid context BUG
+    - pinctrl: ralink: rename MT7628(an) functions to MT76X8
+    - pinctrl: ralink: rename pinctrl-rt2880 to pinctrl-ralink
+    - pinctrl: ralink: Check for null return of devm_kcalloc
+    - perf/core: Fix data race between perf_event_set_output() and
+      perf_mmap_close()
+    - ipv4/tcp: do not use per netns ctl sockets
+    - net: tun: split run_ebpf_filter() and pskb_trim() into different "if
+      statement"
+    - mm/pagealloc: sysctl: change watermark_scale_factor max limit to 30%
+    - sysctl: move some boundary constants from sysctl.c to sysctl_vals
+    - tcp: Fix data-races around sysctl_tcp_ecn.
+    - drm/amd/display: Add option to defer works of hpd_rx_irq
+    - drm/amd/display: Fork thread to offload work of hpd_rx_irq
+    - drm/amdgpu/display: add quirk handling for stutter mode
+    - drm/amd/display: Ignore First MST Sideband Message Return Error
+    - scsi: megaraid: Clear READ queue map's nr_queues
+    - scsi: ufs: core: Drop loglevel of WriteBoost message
+    - nvme: check for duplicate identifiers earlier
+    - nvme: fix block device naming collision
+    - igc: Reinstate IGC_REMOVED logic and implement it properly
+    - ip: Fix data-races around sysctl_ip_no_pmtu_disc.
+    - ip: Fix data-races around sysctl_ip_fwd_use_pmtu.
+    - ip: Fix data-races around sysctl_ip_fwd_update_priority.
+    - ip: Fix data-races around sysctl_ip_nonlocal_bind.
+    - ip: Fix a data-race around sysctl_ip_autobind_reuse.
+    - ip: Fix a data-race around sysctl_fwmark_reflect.
+    - tcp/dccp: Fix a data-race around sysctl_tcp_fwmark_accept.
+    - tcp: sk->sk_bound_dev_if once in inet_request_bound_dev_if()
+    - tcp: Fix data-races around sysctl_tcp_l3mdev_accept.
+    - tcp: Fix data-races around sysctl_tcp_mtu_probing.
+    - tcp: Fix data-races around sysctl_tcp_base_mss.
+    - tcp: Fix data-races around sysctl_tcp_min_snd_mss.
+    - tcp: Fix a data-race around sysctl_tcp_mtu_probe_floor.
+    - tcp: Fix a data-race around sysctl_tcp_probe_threshold.
+    - tcp: Fix a data-race around sysctl_tcp_probe_interval.
+    - net: stmmac: fix pm runtime issue in stmmac_dvr_remove()
+    - net: stmmac: fix unbalanced ptp clock issue in suspend/resume flow
+    - mtd: rawnand: gpmi: validate controller clock rate
+    - mtd: rawnand: gpmi: Set WAIT_FOR_READY timeout based on program/erase times
+    - net: dsa: microchip: ksz_common: Fix refcount leak bug
+    - net: skb: introduce kfree_skb_reason()
+    - net: skb: use kfree_skb_reason() in tcp_v4_rcv()
+    - net: skb: use kfree_skb_reason() in __udp4_lib_rcv()
+    - net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
+    - net: skb_drop_reason: add document for drop reasons
+    - net: netfilter: use kfree_drop_reason() for NF_DROP
+    - net: ipv4: use kfree_skb_reason() in ip_rcv_core()
+    - net: ipv4: use kfree_skb_reason() in ip_rcv_finish_core()
+    - i2c: mlxcpld: Fix register setting for 400KHz frequency
+    - i2c: cadence: Change large transfer count reset logic to be unconditional
+    - perf tests: Fix Convert perf time to TSC test for hybrid
+    - net: stmmac: fix dma queue left shift overflow issue
+    - net/tls: Fix race in TLS device down flow
+    - igmp: Fix data-races around sysctl_igmp_llm_reports.
+    - igmp: Fix a data-race around sysctl_igmp_max_memberships.
+    - igmp: Fix data-races around sysctl_igmp_max_msf.
+    - tcp: Fix data-races around keepalive sysctl knobs.
+    - tcp: Fix data-races around sysctl_tcp_syn(ack)?_retries.
+    - tcp: Fix data-races around sysctl_tcp_syncookies.
+    - tcp: Fix data-races around sysctl_tcp_migrate_req.
+    - tcp: Fix data-races around sysctl_tcp_reordering.
+    - tcp: Fix data-races around some timeout sysctl knobs.
+    - tcp: Fix a data-race around sysctl_tcp_notsent_lowat.
+    - tcp: Fix a data-race around sysctl_tcp_tw_reuse.
+    - tcp: Fix data-races around sysctl_max_syn_backlog.
+    - tcp: Fix data-races around sysctl_tcp_fastopen.
+    - tcp: Fix data-races around sysctl_tcp_fastopen_blackhole_timeout.
+    - iavf: Fix handling of dummy receive descriptors
+    - pinctrl: armada-37xx: Use temporary variable for struct device
+    - pinctrl: armada-37xx: Make use of the devm_platform_ioremap_resource()
+    - pinctrl: armada-37xx: Convert to use dev_err_probe()
+    - pinctrl: armada-37xx: use raw spinlocks for regmap to avoid invalid wait
+      context
+    - i40e: Fix erroneous adapter reinitialization during recovery process
+    - ixgbe: Add locking to prevent panic when setting sriov_numvfs to zero
+    - net: stmmac: remove redunctant disable xPCS EEE call
+    - gpio: pca953x: only use single read/write for No AI mode
+    - gpio: pca953x: use the correct range when do regmap sync
+    - gpio: pca953x: use the correct register address when regcache sync during
+      init
+    - be2net: Fix buffer overflow in be_get_module_eeprom
+    - net: dsa: sja1105: silent spi_device_id warnings
+    - net: dsa: vitesse-vsc73xx: silent spi_device_id warnings
+    - drm/imx/dcss: Add missing of_node_put() in fail path
+    - ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh.
+    - ipv4: Fix data-races around sysctl_fib_multipath_hash_policy.
+    - ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
+    - ip: Fix data-races around sysctl_ip_prot_sock.
+    - udp: Fix a data-race around sysctl_udp_l3mdev_accept.
+    - tcp: Fix data-races around sysctl knobs related to SYN option.
+    - tcp: Fix a data-race around sysctl_tcp_early_retrans.
+    - tcp: Fix data-races around sysctl_tcp_recovery.
+    - tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
+    - tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
+    - tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
+    - tcp: Fix a data-race around sysctl_tcp_stdurg.
+    - tcp: Fix a data-race around sysctl_tcp_rfc1337.
+    - tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
+    - tcp: Fix data-races around sysctl_tcp_max_reordering.
+    - gpio: gpio-xilinx: Fix integer overflow
+    - KVM: selftests: Fix target thread to be migrated in rseq_test
+    - spi: bcm2835: bcm2835_spi_handle_err(): fix NULL pointer deref for non DMA
+      transfers
+    - KVM: Don't null dereference ops->destroy
+    - mm/mempolicy: fix uninit-value in mpol_rebind_policy()
+    - bpf: Make sure mac_header was set before using it
+    - sched/deadline: Fix BUG_ON condition for deboosted tasks
+    - x86/bugs: Warn when "ibrs" mitigation is selected on Enhanced IBRS parts
+    - dlm: fix pending remove if msg allocation fails
+    - x86/uaccess: Implement macros for CMPXCHG on user addresses
+    - bitfield.h: Fix "type of reg too small for mask" test
+    - x86/entry_32: Remove .fixup usage
+    - x86/extable: Extend extable functionality
+    - x86/msr: Remove .fixup usage
+    - x86/futex: Remove .fixup usage
+    - KVM: x86: Use __try_cmpxchg_user() to emulate atomic accesses
+    - xhci: dbc: refactor xhci_dbc_init()
+    - xhci: dbc: create and remove dbc structure in dbgtty driver.
+    - xhci: dbc: Rename xhci_dbc_init and xhci_dbc_exit
+    - xhci: Set HCD flag to defer primary roothub registration
+    - mt76: fix use-after-free by removing a non-RCU wcid pointer
+    - iwlwifi: fw: uefi: add missing include guards
+    - crypto: qat - set to zero DH parameters before free
+    - crypto: qat - use pre-allocated buffers in datapath
+    - crypto: qat - refactor submission logic
+    - crypto: qat - add backlog mechanism
+    - crypto: qat - fix memory leak in RSA
+    - crypto: qat - remove dma_free_coherent() for RSA
+    - crypto: qat - remove dma_free_coherent() for DH
+    - crypto: qat - add param check for RSA
+    - crypto: qat - add param check for DH
+    - crypto: qat - re-enable registration of algorithms
+    - exfat: fix referencing wrong parent directory information after renaming
+    - tracing: Have event format check not flag %p* on __get_dynamic_array()
+    - tracing: Place trace_pid_list logic into abstract functions
+    - tracing: Fix return value of trace_pid_write()
+    - um: virtio_uml: Allow probing from devicetree
+    - um: virtio_uml: Fix broken device handling in time-travel
+    - Bluetooth: Add bt_skb_sendmsg helper
+    - Bluetooth: Add bt_skb_sendmmsg helper
+    - Bluetooth: SCO: Replace use of memcpy_from_msg with bt_skb_sendmsg
+    - Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg
+    - Bluetooth: Fix passing NULL to PTR_ERR
+    - Bluetooth: SCO: Fix sco_send_frame returning skb->len
+    - Bluetooth: Fix bt_skb_sendmmsg not allocating partial chunks
+    - exfat: use updated exfat_chain directly during renaming
+    - x86/amd: Use IBPB for firmware calls
+    - x86/alternative: Report missing return thunk details
+    - watchqueue: make sure to serialize 'wqueue->defunct' properly
+    - tty: drivers/tty/, stop using tty_schedule_flip()
+    - tty: the rest, stop using tty_schedule_flip()
+    - tty: drop tty_schedule_flip()
+    - tty: extract tty_flip_buffer_commit() from tty_flip_buffer_push()
+    - tty: use new tty_insert_flip_string_and_push_buffer() in pty_write()
+    - watch-queue: remove spurious double semicolon
+    - drm/amd/display: invalid parameter check in dmub_hpd_callback
+    - x86/extable: Prefer local labels in .set directives
+    - KVM: x86: fix typo in __try_cmpxchg_user causing non-atomicness
+    - x86: drop bogus "cc" clobber from __try_cmpxchg_user_asm()
+    - drm/amdgpu: Off by one in dm_dmub_outbox1_low_irq()
+    - x86/entry_32: Fix segment exceptions
+    - Linux 5.15.58
+  * Jammy update: v5.15.57 upstream stable release (LP: #1988353)
+    - x86/xen: Fix initialisation in hypercall_page after rethunk
+    - tools arch x86: Sync the msr-index.h copy with the kernel sources
+    - tools headers cpufeatures: Sync with the kernel sources
+    - um: Add missing apply_returns()
+    - x86: Use -mindirect-branch-cs-prefix for RETPOLINE builds
+    - Linux 5.15.57
+  * Jammy update: v5.15.56 upstream stable release (LP: #1988351)
+    - ALSA: hda - Add fixup for Dell Latitidue E5430
+    - ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
+    - ALSA: hda/realtek: Fix headset mic for Acer SF313-51
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
+    - ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
+    - xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
+    - fix race between exit_itimers() and /proc/pid/timers
+    - mm: userfaultfd: fix UFFDIO_CONTINUE on fallocated shmem pages
+    - mm: split huge PUD on wp_huge_pud fallback
+    - tracing/histograms: Fix memory leak problem
+    - net: sock: tracing: Fix sock_exceed_buf_limit not to dereference stale
+      pointer
+    - ip: fix dflt addr selection for connected nexthop
+    - ARM: 9213/1: Print message about disabled Spectre workarounds only once
+    - ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
+    - wifi: mac80211: fix queue selection for mesh/OCB interfaces
+    - cgroup: Use separate src/dst nodes when preloading css_sets for migration
+    - btrfs: return -EAGAIN for NOWAIT dio reads/writes on compressed and inline
+      extents
+    - drm/panfrost: Put mapping instead of shmem obj on
+      panfrost_mmu_map_fault_addr() error
+    - drm/panfrost: Fix shrinker list corruption by madvise IOCTL
+    - fs/remap: constrain dedupe of EOF blocks
+    - nilfs2: fix incorrect masking of permission flags for symlinks
+    - sh: convert nommu io{re,un}map() to static inline functions
+    - Revert "evm: Fix memleak in init_desc"
+    - xfs: only run COW extent recovery when there are no live extents
+    - xfs: don't include bnobt blocks when reserving free block pool
+    - xfs: run callbacks before waking waiters in xlog_state_shutdown_callbacks
+    - xfs: drop async cache flushes from CIL commits.
+    - reset: Fix devm bulk optional exclusive control getter
+    - ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
+    - spi: amd: Limit max transfer and message size
+    - ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
+    - ARM: 9210/1: Mark the FDT_FIXED sections as shareable
+    - net/mlx5e: kTLS, Fix build time constant test in TX
+    - net/mlx5e: kTLS, Fix build time constant test in RX
+    - net/mlx5e: Fix enabling sriov while tc nic rules are offloaded
+    - net/mlx5e: Fix capability check for updating vnic env counters
+    - net/mlx5e: Ring the TX doorbell on DMA errors
+    - drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
+    - ima: Fix a potential integer overflow in ima_appraise_measurement
+    - ASoC: sgtl5000: Fix noise on shutdown/remove
+    - ASoC: tas2764: Add post reset delays
+    - ASoC: tas2764: Fix and extend FSYNC polarity handling
+    - ASoC: tas2764: Correct playback volume range
+    - ASoC: tas2764: Fix amp gain register offset & default
+    - ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
+    - ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
+    - net: stmmac: dwc-qos: Disable split header for Tegra194
+    - net: ethernet: ti: am65-cpsw: Fix devlink port register sequence
+    - sysctl: Fix data races in proc_dointvec().
+    - sysctl: Fix data races in proc_douintvec().
+    - sysctl: Fix data races in proc_dointvec_minmax().
+    - sysctl: Fix data races in proc_douintvec_minmax().
+    - sysctl: Fix data races in proc_doulongvec_minmax().
+    - sysctl: Fix data races in proc_dointvec_jiffies().
+    - tcp: Fix a data-race around sysctl_tcp_max_orphans.
+    - inetpeer: Fix data-races around sysctl.
+    - net: Fix data-races around sysctl_mem.
+    - cipso: Fix data-races around sysctl.
+    - icmp: Fix data-races around sysctl.
+    - ipv4: Fix a data-race around sysctl_fib_sync_mem.
+    - ARM: dts: at91: sama5d2: Fix typo in i2s1 node
+    - ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
+    - arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
+    - arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
+    - netfilter: nf_log: incorrect offset to network header
+    - netfilter: nf_tables: replace BUG_ON by element length check
+    - drm/i915/gvt: IS_ERR() vs NULL bug in intel_gvt_update_reg_whitelist()
+    - xen/gntdev: Ignore failure to unmap INVALID_GRANT_HANDLE
+    - lockd: set fl_owner when unlocking files
+    - lockd: fix nlm_close_files
+    - tracing: Fix sleeping while atomic in kdb ftdump
+    - drm/i915/selftests: fix a couple IS_ERR() vs NULL tests
+    - drm/i915/dg2: Add Wa_22011100796
+    - drm/i915/gt: Serialize GRDOM access between multiple engine resets
+    - drm/i915/gt: Serialize TLB invalidates with GT resets
+    - drm/i915/uc: correctly track uc_fw init failure
+    - drm/i915: Require the vm mutex for i915_vma_bind()
+    - bnxt_en: Fix bnxt_reinit_after_abort() code path
+    - bnxt_en: Fix bnxt_refclk_read()
+    - sysctl: Fix data-races in proc_dou8vec_minmax().
+    - sysctl: Fix data-races in proc_dointvec_ms_jiffies().
+    - icmp: Fix data-races around sysctl_icmp_echo_enable_probe.
+    - icmp: Fix a data-race around sysctl_icmp_ignore_bogus_error_responses.
+    - icmp: Fix a data-race around sysctl_icmp_errors_use_inbound_ifaddr.
+    - icmp: Fix a data-race around sysctl_icmp_ratelimit.
+    - icmp: Fix a data-race around sysctl_icmp_ratemask.
+    - raw: Fix a data-race around sysctl_raw_l3mdev_accept.
+    - tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
+    - ipv4: Fix data-races around sysctl_ip_dynaddr.
+    - nexthop: Fix data-races around nexthop_compat_mode.
+    - net: ftgmac100: Hold reference returned by of_get_child_by_name()
+    - net: stmmac: fix leaks in probe
+    - ima: force signature verification when CONFIG_KEXEC_SIG is configured
+    - ima: Fix potential memory leak in ima_init_crypto()
+    - drm/amd/display: Only use depth 36 bpp linebuffers on DCN display engines.
+    - drm/amd/pm: Prevent divide by zero
+    - sfc: fix use after free when disabling sriov
+    - ceph: switch netfs read ops to use rreq->inode instead of
+      rreq->mapping->host
+    - seg6: fix skb checksum evaluation in SRH encapsulation/insertion
+    - seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
+    - seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
+    - sfc: fix kernel panic when creating VF
+    - KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
+    - net/tls: Check for errors in tls_device_init
+    - ACPI: video: Fix acpi_video_handles_brightness_key_presses()
+    - mm: sysctl: fix missing numa_stat when !CONFIG_HUGETLB_PAGE
+    - btrfs: rename btrfs_bio to btrfs_io_context
+    - btrfs: zoned: fix a leaked bioc in read_zone_info
+    - ksmbd: use SOCK_NONBLOCK type for kernel_accept()
+    - powerpc/xive/spapr: correct bitmap allocation size
+    - vdpa/mlx5: Initialize CVQ vringh only once
+    - vduse: Tie vduse mgmtdev and its device
+    - virtio_mmio: Add missing PM calls to freeze/restore
+    - virtio_mmio: Restore guest page size on resume
+    - netfilter: br_netfilter: do not skip all hooks with 0 priority
+    - scsi: hisi_sas: Limit max hw sectors for v3 HW
+    - cpufreq: pmac32-cpufreq: Fix refcount leak bug
+    - firmware: sysfb: Make sysfb_create_simplefb() return a pdev pointer
+    - firmware: sysfb: Add sysfb_disable() helper function
+    - fbdev: Disable sysfb device registration when removing conflicting FBs
+    - net: tipc: fix possible refcount leak in tipc_sk_create()
+    - NFC: nxp-nci: don't print header length mismatch on i2c error
+    - nvme-tcp: always fail a request when sending it failed
+    - nvme: fix regression when disconnect a recovering ctrl
+    - net: sfp: fix memory leak in sfp_probe()
+    - ASoC: ops: Fix off by one in range control validation
+    - pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux()
+    - ASoC: Realtek/Maxim SoundWire codecs: disable pm_runtime on remove
+    - ASoC: rt711-sdca-sdw: fix calibrate mutex initialization
+    - ASoC: Intel: sof_sdw: handle errors on card registration
+    - ASoC: rt711: fix calibrate mutex initialization
+    - ASoC: rt7*-sdw: harden jack_detect_handler
+    - ASoC: codecs: rt700/rt711/rt711-sdca: initialize workqueues in probe
+    - ASoC: SOF: Intel: hda-loader: Clarify the cl_dsp_init() flow
+    - ASoC: wcd938x: Fix event generation for some controls
+    - ASoC: Intel: bytcr_wm5102: Fix GPIO related probe-ordering problem
+    - ASoC: wm5110: Fix DRE control
+    - ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error
+    - ASoC: dapm: Initialise kcontrol data for mux/demux controls
+    - ASoC: cs47l15: Fix event generation for low power mux control
+    - ASoC: madera: Fix event generation for OUT1 demux
+    - ASoC: madera: Fix event generation for rate controls
+    - irqchip: or1k-pic: Undefine mask_ack for level triggered hardware
+    - x86: Clear .brk area at early boot
+    - soc: ixp4xx/npe: Fix unused match warning
+    - ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
+    - Revert "can: xilinx_can: Limit CANFD brp to 2"
+    - ALSA: usb-audio: Add quirks for MacroSilicon MS2100/MS2106 devices
+    - ALSA: usb-audio: Add quirk for Fiero SC-01
+    - ALSA: usb-audio: Add quirk for Fiero SC-01 (fw v1.0.0)
+    - nvme-pci: phison e16 has bogus namespace ids
+    - signal handling: don't use BUG_ON() for debugging
+    - USB: serial: ftdi_sio: add Belimo device ids
+    - usb: typec: add missing uevent when partner support PD
+    - usb: dwc3: gadget: Fix event pending check
+    - tty: serial: samsung_tty: set dma burst_size to 1
+    - vt: fix memory overlapping when deleting chars in the buffer
+    - serial: 8250: fix return error code in serial8250_request_std_resource()
+    - serial: stm32: Clear prev values before setting RTS delays
+    - serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle
+    - serial: 8250: Fix PM usage_count for console handover
+    - x86/pat: Fix x86_has_pat_wp()
+    - drm/aperture: Run fbdev removal before internal helpers
+    - Linux 5.15.56
+  * Jammy update: v5.15.55 upstream stable release (LP: #1988338)
+    - Linux 5.15.55
+  * Jammy update: v5.15.54 upstream stable release (LP: #1987451)
+    - mm/slub: add missing TID updates on slab deactivation
+    - mm/filemap: fix UAF in find_lock_entries
+    - Revert "selftests/bpf: Add test for bpf_timer overwriting crash"
+    - ALSA: usb-audio: Workarounds for Behringer UMC 204/404 HD
+    - ALSA: hda/realtek: Add quirk for Clevo L140PU
+    - ALSA: cs46xx: Fix missing snd_card_free() call at probe error
+    - can: bcm: use call_rcu() instead of costly synchronize_rcu()
+    - can: grcan: grcan_probe(): remove extra of_node_get()
+    - can: gs_usb: gs_usb_open/close(): fix memory leak
+    - can: m_can: m_can_chip_config(): actually enable internal timestamping
+    - can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32
+      bits
+    - can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for
+      mcp2517fd
+    - can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on
+      TBC register
+    - bpf: Fix incorrect verifier simulation around jmp32's jeq/jne
+    - bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
+    - usbnet: fix memory leak in error case
+    - net: rose: fix UAF bug caused by rose_t0timer_expiry
+    - netfilter: nft_set_pipapo: release elements in clone from abort path
+    - btrfs: rename btrfs_alloc_chunk to btrfs_create_chunk
+    - btrfs: add additional parameters to btrfs_init_tree_ref/btrfs_init_data_ref
+    - btrfs: fix invalid delayed ref after subvolume creation failure
+    - btrfs: fix warning when freeing leaf after subvolume creation failure
+    - Input: cpcap-pwrbutton - handle errors from platform_get_irq()
+    - Input: goodix - change goodix_i2c_write() len parameter type to int
+    - Input: goodix - add a goodix.h header file
+    - Input: goodix - refactor reset handling
+    - Input: goodix - try not to touch the reset-pin on x86/ACPI devices
+    - dma-buf/poll: Get a file reference for outstanding fence callbacks
+    - btrfs: fix deadlock between chunk allocation and chunk btree modifications
+    - drm/i915: Disable bonding on gen12+ platforms
+    - drm/i915/gt: Register the migrate contexts with their engines
+    - drm/i915: Replace the unconditional clflush with drm_clflush_virt_range()
+    - media: ir_toy: prevent device from hanging during transmit
+    - memory: renesas-rpc-if: Avoid unaligned bus access for HyperFlash
+    - ath11k: add hw_param for wakeup_mhi
+    - qed: Improve the stack space of filter_config()
+    - platform/x86: wmi: introduce helper to convert driver to WMI driver
+    - platform/x86: wmi: Replace read_takes_no_args with a flags field
+    - platform/x86: wmi: Fix driver->notify() vs ->probe() race
+    - mt76: mt7921: get rid of mt7921_mac_set_beacon_filter
+    - mt76: mt7921: introduce mt7921_mcu_set_beacon_filter utility routine
+    - mt76: mt7921: fix a possible race enabling/disabling runtime-pm
+    - bpf: Stop caching subprog index in the bpf_pseudo_func insn
+    - bpf, arm64: Use emit_addr_mov_i64() for BPF_PSEUDO_FUNC
+    - riscv: defconfig: enable DRM_NOUVEAU
+    - RISC-V: defconfigs: Set CONFIG_FB=y, for FB console
+    - net/mlx5e: Check action fwd/drop flag exists also for nic flows
+    - net/mlx5e: Split actions_match_supported() into a sub function
+    - net/mlx5e: TC, Reject rules with drop and modify hdr action
+    - net/mlx5e: TC, Reject rules with forward and drop actions
+    - ASoC: rt5682: Avoid the unexpected IRQ event during going to suspend
+    - ASoC: rt5682: Re-detect the combo jack after resuming
+    - ASoC: rt5682: Fix deadlock on resume
+    - netfilter: nf_tables: convert pktinfo->tprot_set to flags field
+    - netfilter: nft_payload: support for inner header matching / mangling
+    - netfilter: nft_payload: don't allow th access for fragments
+    - s390/boot: allocate amode31 section in decompressor
+    - s390/setup: use physical pointers for memblock_reserve()
+    - s390/setup: preserve memory at OLDMEM_BASE and OLDMEM_SIZE
+    - ibmvnic: init init_done_rc earlier
+    - ibmvnic: clear fop when retrying probe
+    - ibmvnic: Allow queueing resets during probe
+    - virtio-blk: avoid preallocating big SGL for data
+    - io_uring: ensure that fsnotify is always called
+    - block: use bdev_get_queue() in bio.c
+    - block: only mark bio as tracked if it really is tracked
+    - block: fix rq-qos breakage from skipping rq_qos_done_bio()
+    - stddef: Introduce struct_group() helper macro
+    - media: omap3isp: Use struct_group() for memcpy() region
+    - media: davinci: vpif: fix use-after-free on driver unbind
+    - mt76: mt76_connac: fix MCU_CE_CMD_SET_ROC definition error
+    - mt76: mt7921: do not always disable fw runtime-pm
+    - cxl/port: Hold port reference until decoder release
+    - clk: renesas: r9a07g044: Update multiplier and divider values for PLL2/3
+    - KVM: x86/mmu: Use yield-safe TDP MMU root iter in MMU notifier unmapping
+    - KVM: x86/mmu: Use common TDP MMU zap helper for MMU notifier unmap hook
+    - scsi: qla2xxx: Move heartbeat handling from DPC thread to workqueue
+    - scsi: qla2xxx: Fix laggy FC remote port session recovery
+    - scsi: qla2xxx: edif: Replace list_for_each_safe with
+      list_for_each_entry_safe
+    - scsi: qla2xxx: Fix crash during module load unload test
+    - gfs2: Fix gfs2_file_buffered_write endless loop workaround
+    - vdpa/mlx5: Avoid processing works if workqueue was destroyed
+    - btrfs: handle device lookup with btrfs_dev_lookup_args
+    - btrfs: add a btrfs_get_dev_args_from_path helper
+    - btrfs: use btrfs_get_dev_args_from_path in dev removal ioctls
+    - btrfs: remove device item and update super block in the same transaction
+    - drbd: add error handling support for add_disk()
+    - drbd: Fix double free problem in drbd_create_device
+    - drbd: fix an invalid memory access caused by incorrect use of list iterator
+    - drm/amd/display: Set min dcfclk if pipe count is 0
+    - drm/amd/display: Fix by adding FPU protection for dcn30_internal_validate_bw
+    - NFSD: De-duplicate net_generic(nf->nf_net, nfsd_net_id)
+    - NFSD: COMMIT operations must not return NFS?ERR_INVAL
+    - riscv/mm: Add XIP_FIXUP for riscv_pfn_base
+    - iio: accel: mma8452: use the correct logic to get mma8452_data
+    - batman-adv: Use netif_rx().
+    - mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
+    - Compiler Attributes: add __alloc_size() for better bounds checking
+    - mm: vmalloc: introduce array allocation functions
+    - KVM: use __vcalloc for very large allocations
+    - btrfs: don't access possibly stale fs_info data in device_list_add
+    - KVM: s390x: fix SCK locking
+    - scsi: qla2xxx: Fix loss of NVMe namespaces after driver reload test
+    - powerpc/32: Don't use lmw/stmw for saving/restoring non volatile regs
+    - powerpc: flexible GPR range save/restore macros
+    - powerpc/tm: Fix more userspace r13 corruption
+    - serial: sc16is7xx: Clear RS485 bits in the shutdown
+    - bus: mhi: core: Use correctly sized arguments for bit field
+    - bus: mhi: Fix pm_state conversion to string
+    - stddef: Introduce DECLARE_FLEX_ARRAY() helper
+    - uapi/linux/stddef.h: Add include guards
+    - ASoC: rt5682: move clk related code to rt5682_i2c_probe
+    - ASoC: rt5682: fix an incorrect NULL check on list iterator
+    - drm/amd/vcn: fix an error msg on vcn 3.0
+    - KVM: Don't create VM debugfs files outside of the VM directory
+    - tty: n_gsm: Modify CR,PF bit when config requester
+    - tty: n_gsm: Save dlci address open status when config requester
+    - tty: n_gsm: fix frame reception handling
+    - ALSA: usb-audio: add mapping for MSI MPG X570S Carbon Max Wifi.
+    - ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.
+    - tty: n_gsm: fix missing update of modem controls after DLCI open
+    - btrfs: zoned: encapsulate inode locking for zoned relocation
+    - btrfs: zoned: use dedicated lock for data relocation
+    - KVM: Initialize debugfs_dentry when a VM is created to avoid NULL deref
+    - mm/hwpoison: mf_mutex for soft offline and unpoison
+    - mm/hwpoison: avoid the impact of hwpoison_filter() return value on mce
+      handler
+    - mm/memory-failure.c: fix race with changing page compound again
+    - mm/hwpoison: fix race between hugetlb free/demotion and
+      memory_failure_hugetlb()
+    - tty: n_gsm: fix invalid use of MSC in advanced option
+    - tty: n_gsm: fix sometimes uninitialized warning in gsm_dlci_modem_output()
+    - serial: 8250_mtk: Make sure to select the right FEATURE_SEL
+    - tty: n_gsm: fix invalid gsmtty_write_room() result
+    - drm/i915: Fix a race between vma / object destruction and unbinding
+    - drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb
+    - drm/mediatek: Remove the pointer of struct cmdq_client
+    - drm/mediatek: Detect CMDQ execution timeout
+    - drm/mediatek: Add cmdq_handle in mtk_crtc
+    - drm/mediatek: Add vblank register/unregister callback functions
+    - Bluetooth: protect le accept and resolv lists with hdev->lock
+    - Bluetooth: btmtksdio: fix use-after-free at btmtksdio_recv_event
+    - io_uring: avoid io-wq -EAGAIN looping for !IOPOLL
+    - irqchip/gic-v3: Ensure pseudo-NMIs have an ISB between ack and handling
+    - irqchip/gic-v3: Refactor ISB + EOIR at ack time
+    - rxrpc: Fix locking issue
+    - dt-bindings: soc: qcom: smd-rpm: Add compatible for MSM8953 SoC
+    - dt-bindings: soc: qcom: smd-rpm: Fix missing MSM8936 compatible
+    - module: change to print useful messages from elf_validity_check()
+    - module: fix [e_shstrndx].sh_size=0 OOB access
+    - iommu/vt-d: Fix PCI bus rescan device hot add
+    - fbdev: fbmem: Fix logo center image dx issue
+    - PM: runtime: Redefine pm_runtime_release_supplier()
+    - memregion: Fix memregion_free() fallback definition
+    - video: of_display_timing.h: include errno.h
+    - powerpc/powernv: delay rng platform device creation until later in boot
+    - net: dsa: qca8k: reset cpu port on MTU change
+    - can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
+    - can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
+    - can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
+    - xfs: remove incorrect ASSERT in xfs_rename
+    - Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown"
+    - btrfs: fix error pointer dereference in btrfs_ioctl_rm_dev_v2()
+    - virtio-blk: modify the value type of num in virtio_queue_rq()
+    - btrfs: fix use of uninitialized variable at rm device ioctl
+    - tty: n_gsm: fix encoding of command/response bit
+    - ARM: meson: Fix refcount leak in meson_smp_prepare_cpus
+    - pinctrl: sunxi: a83t: Fix NAND function name for some pins
+    - ASoC: rt711: Add endianness flag in snd_soc_component_driver
+    - ASoC: rt711-sdca: Add endianness flag in snd_soc_component_driver
+    - ASoC: codecs: rt700/rt711/rt711-sdca: resume bus/codec in .set_jack_detect
+    - arm64: dts: qcom: msm8994: Fix CPU6/7 reg values
+    - arm64: dts: qcom: sdm845: use dispcc AHB clock for mdss node
+    - ARM: mxs_defconfig: Enable the framebuffer
+    - arm64: dts: imx8mp-evk: correct mmc pad settings
+    - arm64: dts: imx8mp-evk: correct the uart2 pinctl value
+    - arm64: dts: imx8mp-evk: correct gpio-led pad settings
+    - arm64: dts: imx8mp-evk: correct vbus pad settings
+    - arm64: dts: imx8mp-evk: correct eqos pad settings
+    - arm64: dts: imx8mp-evk: correct I2C1 pad settings
+    - arm64: dts: imx8mp-evk: correct I2C3 pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct uart pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct eqos pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct i2c2 & mmc settings
+    - pinctrl: sunxi: sunxi_pconf_set: use correct offset
+    - arm64: dts: qcom: msm8992-*: Fix vdd_lvs1_2-supply typo
+    - ARM: at91: pm: use proper compatible for sama5d2's rtc
+    - ARM: at91: pm: use proper compatibles for sam9x60's rtc and rtt
+    - ARM: at91: pm: use proper compatibles for sama7g5's rtc and rtt
+    - ARM: dts: at91: sam9x60ek: fix eeprom compatible and size
+    - ARM: dts: at91: sama5d2_icp: fix eeprom compatibles
+    - ARM: at91: fix soc detection for SAM9X60 SiPs
+    - xsk: Clear page contiguity bit when unmapping pool
+    - i2c: piix4: Fix a memory leak in the EFCH MMIO support
+    - i40e: Fix dropped jumbo frames statistics
+    - i40e: Fix VF's MAC Address change on VM
+    - ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
+    - ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
+    - ibmvnic: Properly dispose of all skbs during a failover.
+    - selftests: forwarding: fix flood_unicast_test when h2 supports
+      IFF_UNICAST_FLT
+    - selftests: forwarding: fix learning_test when h1 supports IFF_UNICAST_FLT
+    - selftests: forwarding: fix error message in learning_test
+    - r8169: fix accessing unset transport header
+    - i2c: cadence: Unregister the clk notifier in error path
+    - dmaengine: imx-sdma: Allow imx8m for imx7 FW revs
+    - misc: rtsx_usb: fix use of dma mapped buffer for usb bulk transfer
+    - misc: rtsx_usb: use separate command and response buffers
+    - misc: rtsx_usb: set return value in rsp_buf alloc err path
+    - Revert "mm/memory-failure.c: fix race with changing page compound again"
+    - Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
+    - dt-bindings: dma: allwinner,sun50i-a64-dma: Fix min/max typo
+    - ida: don't use BUG_ON() for debugging
+    - dmaengine: pl330: Fix lockdep warning about non-static key
+    - dmaengine: lgm: Fix an error handling path in intel_ldma_probe()
+    - dmaengine: at_xdma: handle errors of at_xdmac_alloc_desc() correctly
+    - dmaengine: ti: Fix refcount leak in ti_dra7_xbar_route_allocate
+    - dmaengine: qcom: bam_dma: fix runtime PM underflow
+    - dmaengine: ti: Add missing put_device in ti_dra7_xbar_route_allocate
+    - dmaengine: idxd: force wq context cleanup on device disable path
+    - selftests/net: fix section name when using xdp_dummy.o
+    - Linux 5.15.54
+
+  [ Ubuntu: 5.15.0-48.54 ]
+
+  * jammy/linux: 5.15.0-48.54 -proposed tracker (LP: #1987775)
+  * System freeze after resuming from suspend due to PCI ASPM settings
+    (LP: #1980829)
+    - SAUCE: PCI/ASPM: Save/restore L1SS Capability for suspend/resume
+    - SAUCE: whitelist platforms that needs save/restore ASPM L1SS for
+      suspend/resume
+  * [SRU][J/OEM-5.17][PATCH 0/1] Fix oled brightness set above frame-average
+    luminance (LP: #1978986)
+    - SAUCE: drm: New function to get luminance range based on static hdr metadata
+    - SAUCE: drm/amdgpu_dm: Rely on split out luminance calculation function
+    - SAUCE: drm/i915: Use luminance range calculated during edid parsing
+  * Jammy: Add OVS Internal Port HW Offload to mlx5 driver (LP: #1983498)
+    - net/mlx5e: Refactor rx handler of represetor device
+    - net/mlx5e: Use generic name for the forwarding dev pointer
+    - net/mlx5: E-Switch, Add ovs internal port mapping to metadata support
+    - net/mlx5e: Support accept action
+    - net/mlx5e: Accept action skbedit in the tc actions list
+    - net/mlx5e: Offload tc rules that redirect to ovs internal port
+    - net/mlx5e: Offload internal port as encap route device
+    - net/mlx5e: Enable TC offload for ingress MACVLAN
+    - net/mlx5e: Add indirect tc offload of ovs internal port
+    - net/mlx5e: Term table handling of internal port rules
+    - net/mlx5: Support internal port as decap route device
+    - net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'
+    - net/mlx5e: TC, Fix memory leak with rules with internal port
+    - net/mlx5e: Fix skb memory leak when TC classifier action offloads are
+      disabled
+    - net/mlx5e: Fix nullptr on deleting mirroring rule
+    - net/mlx5e: Avoid implicit modify hdr for decap drop rule
+    - net/mlx5e: Fix wrong source vport matching on tunnel rule
+    - net/mlx5e: TC, fix decap fallback to uplink when int port not supported
+  * Remove unused variable from i915 psr (LP: #1986798)
+    - SAUCE: drm/i915/display/psr: Remove unused variable
+  * refactoring of overlayfs fix to properly support shiftfs (LP: #1983640)
+    - SAUCE: overlayfs: remove CONFIG_AUFS_FS dependency
+  * Jammy update: v5.15.53 upstream stable release (LP: #1986728)
+    - Revert "drm/amdgpu/display: set vblank_disable_immediate for DC"
+    - drm/amdgpu: To flush tlb for MMHUB of RAVEN series
+    - ksmbd: set the range of bytes to zero without extending file size in
+      FSCTL_ZERO_DATA
+    - ksmbd: check invalid FileOffset and BeyondFinalZero in FSCTL_ZERO_DATA
+    - ksmbd: use vfs_llseek instead of dereferencing NULL
+    - ipv6: take care of disable_policy when restoring routes
+    - net: phy: Don't trigger state machine while in suspend
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG SX6000LNP (AKA SPECTRIX
+      S40G)
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA IM2P33F8ABR1
+    - nvdimm: Fix badblocks clear off-by-one error
+    - powerpc/prom_init: Fix kernel config grep
+    - powerpc/book3e: Fix PUD allocation size in map_kernel_page()
+    - powerpc/bpf: Fix use of user_pt_regs in uapi
+    - dm raid: fix accesses beyond end of raid member array
+    - dm raid: fix KASAN warning in raid5_add_disks
+    - s390/archrandom: simplify back to earlier design and initialize earlier
+    - SUNRPC: Fix READ_PLUS crasher
+    - net: rose: fix UAF bugs caused by timer handler
+    - net: usb: ax88179_178a: Fix packet receiving
+    - virtio-net: fix race between ndo_open() and virtio_device_ready()
+    - selftests/net: pass ipv6_args to udpgso_bench's IPv6 TCP test
+    - net: dsa: bcm_sf2: force pause link settings
+    - net: tun: unlink NAPI from device on destruction
+    - net: tun: stop NAPI when detaching queues
+    - net: dp83822: disable false carrier interrupt
+    - net: dp83822: disable rx error interrupt
+    - RDMA/qedr: Fix reporting QP timeout attribute
+    - RDMA/cm: Fix memory leak in ib_cm_insert_listen
+    - linux/dim: Fix divide by 0 in RDMA DIM
+    - net: usb: asix: do not force pause frames support
+    - usbnet: fix memory allocation in helpers
+    - selftests: mptcp: more stable diag tests
+    - net: ipv6: unexport __init-annotated seg6_hmac_net_init()
+    - NFSD: restore EINVAL error translation in nfsd_commit()
+    - vfs: fix copy_file_range() regression in cross-fs copies
+    - caif_virtio: fix race between virtio_device_ready() and ndo_open()
+    - PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
+    - vdpa/mlx5: Update Control VQ callback information
+    - s390: remove unneeded 'select BUILD_BIN2C'
+    - netfilter: nft_dynset: restore set element counter when failing to update
+    - net/dsa/hirschmann: Add missing of_node_get() in hellcreek_led_setup()
+    - net/sched: act_api: Notify user space if any actions were flushed before
+      error
+    - net: asix: fix "can't send until first packet is send" issue
+    - net: bonding: fix possible NULL deref in rlb code
+    - net: phy: ax88772a: fix lost pause advertisement configuration
+    - net: bonding: fix use-after-free after 802.3ad slave unbind
+    - powerpc/memhotplug: Add add_pages override for PPC
+    - nfc: nfcmrvl: Fix irq_of_parse_and_map() return value
+    - NFC: nxp-nci: Don't issue a zero length i2c_master_read()
+    - tipc: move bc link creation back to tipc_node_create
+    - epic100: fix use after free on rmmod
+    - io_uring: ensure that send/sendmsg and recv/recvmsg check sqe->ioprio
+    - ACPI: video: Change how we determine if brightness key-presses are handled
+    - tunnels: do not assume mac header is set in skb_tunnel_check_pmtu()
+    - ipv6/sit: fix ipip6_tunnel_get_prl return value
+    - ipv6: fix lockdep splat in in6_dump_addrs()
+    - mlxsw: spectrum_router: Fix rollback in tunnel next hop init
+    - net: tun: avoid disabling NAPI twice
+    - MAINTAINERS: add Leah as xfs maintainer for 5.15.y
+    - tcp: add a missing nf_reset_ct() in 3WHS handling
+    - selftests/bpf: Add test_verifier support to fixup kfunc call insns
+    - selftests/rseq: remove ARRAY_SIZE define from individual tests
+    - selftests/rseq: introduce own copy of rseq uapi header
+    - selftests/rseq: Remove useless assignment to cpu variable
+    - selftests/rseq: Remove volatile from __rseq_abi
+    - selftests/rseq: Introduce rseq_get_abi() helper
+    - selftests/rseq: Introduce thread pointer getters
+    - selftests/rseq: Uplift rseq selftests for compatibility with glibc-2.35
+    - selftests/rseq: Fix ppc32: wrong rseq_cs 32-bit field pointer on big endian
+    - selftests/rseq: Fix ppc32 missing instruction selection "u" and "x" for
+      load/store
+    - selftests/rseq: Fix ppc32 offsets by using long rather than off_t
+    - selftests/rseq: Fix warnings about #if checks of undefined tokens
+    - selftests/rseq: Remove arm/mips asm goto compiler work-around
+    - selftests/rseq: Fix: work-around asm goto compiler bugs
+    - selftests/rseq: x86-64: use %fs segment selector for accessing rseq thread
+      area
+    - selftests/rseq: x86-32: use %gs segment selector for accessing rseq thread
+      area
+    - selftests/rseq: Change type of rseq_offset to ptrdiff_t
+    - xen/blkfront: fix leaking data in shared pages
+    - xen/netfront: fix leaking data in shared pages
+    - xen/netfront: force data bouncing when backend is untrusted
+    - xen/blkfront: force data bouncing when backend is untrusted
+    - xen-netfront: restore __skb_queue_tail() positioning in
+      xennet_get_responses()
+    - xen/arm: Fix race in RB-tree based P2M accounting
+    - net: usb: qmi_wwan: add Telit 0x1070 composition
+    - clocksource/drivers/ixp4xx: remove EXPORT_SYMBOL_GPL from
+      ixp4xx_timer_setup()
+    - fsi: occ: Force sequence numbering per OCC
+    - net: fix IFF_TX_SKB_NO_LINEAR definition
+    - drm/i915/gem: add missing else
+    - drm/msm/gem: Fix error return on fence id alloc fail
+    - drivers: cpufreq: Add missing of_node_put() in qoriq-cpufreq.c
+    - platform/x86: panasonic-laptop: de-obfuscate button codes
+    - platform/x86: panasonic-laptop: sort includes alphabetically
+    - platform/x86: panasonic-laptop: revert "Resolve hotkey double trigger bug"
+    - platform/x86: panasonic-laptop: don't report duplicate brightness key-
+      presses
+    - platform/x86: panasonic-laptop: filter out duplicate volume up/down/mute
+      keypresses
+    - drm/fourcc: fix integer type usage in uapi header
+    - hwmon: (occ) Remove sequence numbering and checksum calculation
+    - hwmon: (occ) Prevent power cap command overwriting poll response
+    - hwmon: (ibmaem) don't call platform_device_del() if platform_device_add()
+      fails
+    - Linux 5.15.53
+  * Jammy update: v5.15.52 upstream stable release (LP: #1986724)
+    - tick/nohz: unexport __init-annotated tick_nohz_full_setup()
+    - xfs: use kmem_cache_free() for kmem_cache objects
+    - xfs: punch out data fork delalloc blocks on COW writeback failure
+    - xfs: Fix the free logic of state in xfs_attr_node_hasname
+    - xfs: remove all COW fork extents when remounting readonly
+    - xfs: check sb_meta_uuid for dabuf buffer recovery
+    - xfs: prevent UAF in xfs_log_item_in_current_chkpt
+    - xfs: only bother with sync_filesystem during readonly remount
+    - powerpc/ftrace: Remove ftrace init tramp once kernel init is complete
+    - fs: add is_idmapped_mnt() helper
+    - fs: move mapping helpers
+    - fs: tweak fsuidgid_has_mapping()
+    - fs: account for filesystem mappings
+    - docs: update mapping documentation
+    - fs: use low-level mapping helpers
+    - fs: remove unused low-level mapping helpers
+    - fs: port higher-level mapping helpers
+    - fs: add i_user_ns() helper
+    - fs: support mapped mounts of mapped filesystems
+    - fs: fix acl translation
+    - fs: account for group membership
+    - rtw88: 8821c: support RFE type4 wifi NIC
+    - rtw88: rtw8821c: enable rfe 6 devices
+    - net: mscc: ocelot: allow unregistered IP multicast flooding to CPU
+    - io_uring: fix not locked access to fixed buf table
+    - Linux 5.15.52
+  * Jammy update: v5.15.51 upstream stable release (LP: #1986718)
+    - random: schedule mix_interrupt_randomness() less often
+    - random: quiet urandom warning ratelimit suppression message
+    - ALSA: hda/via: Fix missing beep setup
+    - ALSA: hda/conexant: Fix missing beep setup
+    - ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop
+    - ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
+    - ALSA: hda/realtek: Add quirk for Clevo PD70PNT
+    - ALSA: hda/realtek: Add quirk for Clevo NS50PU
+    - net: openvswitch: fix parsing of nw_proto for IPv6 fragments
+    - 9p: Fix refcounting during full path walks for fid lookups
+    - 9p: fix fid refcount leak in v9fs_vfs_atomic_open_dotl
+    - 9p: fix fid refcount leak in v9fs_vfs_get_link
+    - btrfs: fix hang during unmount when block group reclaim task is running
+    - btrfs: prevent remounting to v1 space cache for subpage mount
+    - btrfs: add error messages to all unrecognized mount options
+    - scsi: ibmvfc: Store vhost pointer during subcrq allocation
+    - scsi: ibmvfc: Allocate/free queue resource only during probe/remove
+    - mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing
+    - mmc: mediatek: wait dma stop bit reset to 0
+    - xen/gntdev: Avoid blocking in unmap_grant_pages()
+    - MAINTAINERS: Add new IOMMU development mailing list
+    - ata: libata: add qc->flags in ata_qc_complete_template tracepoint
+    - dm era: commit metadata in postsuspend after worker stops
+    - dm mirror log: clear log bits up to BITS_PER_LONG boundary
+    - tracing/kprobes: Check whether get_kretprobe() returns NULL in
+      kretprobe_dispatcher()
+    - drm/i915: Implement w/a 22010492432 for adl-s
+    - USB: serial: pl2303: add support for more HXN (G) types
+    - USB: serial: option: add Telit LE910Cx 0x1250 composition
+    - USB: serial: option: add Quectel EM05-G modem
+    - USB: serial: option: add Quectel RM500K module support
+    - drm/msm: Ensure mmap offset is initialized
+    - drm/msm: Fix double pm_runtime_disable() call
+    - netfilter: use get_random_u32 instead of prandom
+    - scsi: scsi_debug: Fix zone transition to full condition
+    - drm/msm: Switch ordering of runpm put vs devfreq_idle
+    - scsi: iscsi: Exclude zero from the endpoint ID range
+    - xsk: Fix generic transmit when completion queue reservation fails
+    - drm/msm: use for_each_sgtable_sg to iterate over scatterlist
+    - bpf: Fix request_sock leak in sk lookup helpers
+    - drm/sun4i: Fix crash during suspend after component bind failure
+    - bpf, x86: Fix tail call count offset calculation on bpf2bpf call
+    - scsi: storvsc: Correct reporting of Hyper-V I/O size limits
+    - phy: aquantia: Fix AN when higher speeds than 1G are not advertised
+    - KVM: arm64: Prevent kmemleak from accessing pKVM memory
+    - net: Write lock dev_base_lock without disabling bottom halves.
+    - net: fix data-race in dev_isalive()
+    - tipc: fix use-after-free Read in tipc_named_reinit
+    - igb: fix a use-after-free issue in igb_clean_tx_ring
+    - bonding: ARP monitor spams NETDEV_NOTIFY_PEERS notifiers
+    - ethtool: Fix get module eeprom fallback
+    - net/sched: sch_netem: Fix arithmetic in netem_dump() for 32-bit platforms
+    - drm/msm/mdp4: Fix refcount leak in mdp4_modeset_init_intf
+    - drm/msm/dp: check core_initialized before disable interrupts at
+      dp_display_unbind()
+    - drm/msm/dp: Drop now unused hpd_high member
+    - drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read failed
+    - drm/msm/dp: do not initialize phy until plugin interrupt received
+    - drm/msm/dp: force link training for display resolution change
+    - perf arm-spe: Don't set data source if it's not a memory operation
+    - erspan: do not assume transport header is always set
+    - net/tls: fix tls_sk_proto_close executed repeatedly
+    - udmabuf: add back sanity check
+    - selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
+    - xen-blkfront: Handle NULL gendisk
+    - x86/xen: Remove undefined behavior in setup_features()
+    - MIPS: Remove repetitive increase irq_err_count
+    - afs: Fix dynamic root getattr
+    - ice: ethtool: advertise 1000M speeds properly
+    - regmap-irq: Fix a bug in regmap_irq_enable() for type_in_mask chips
+    - regmap-irq: Fix offset/index mismatch in read_sub_irq_data()
+    - virtio_net: fix xdp_rxq_info bug after suspend/resume
+    - Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
+    - sock: redo the psock vs ULP protection check
+    - nvme-pci: add NO APST quirk for Kioxia device
+    - nvme: move the Samsung X5 quirk entry to the core quirks
+    - gpio: winbond: Fix error code in winbond_gpio_get()
+    - s390/cpumf: Handle events cycles and instructions identical
+    - iio: mma8452: fix probe fail when device tree compatible is used.
+    - iio: magnetometer: yas530: Fix memchr_inv() misuse
+    - iio: adc: vf610: fix conversion mode sysfs node name
+    - usb: typec: wcove: Drop wrong dependency to INTEL_SOC_PMIC
+    - xhci-pci: Allow host runtime PM as default for Intel Raptor Lake xHCI
+    - xhci-pci: Allow host runtime PM as default for Intel Meteor Lake xHCI
+    - usb: gadget: Fix non-unique driver names in raw-gadget driver
+    - USB: gadget: Fix double-free bug in raw_gadget driver
+    - usb: chipidea: udc: check request status before setting device address
+    - dt-bindings: usb: ohci: Increase the number of PHYs
+    - dt-bindings: usb: ehci: Increase the number of PHYs
+    - btrfs: don't set lock_owner when locking extent buffer for reading
+    - btrfs: fix deadlock with fsync+fiemap+transaction commit
+    - f2fs: attach inline_data after setting compression
+    - iio:humidity:hts221: rearrange iio trigger get and register
+    - iio:chemical:ccs811: rearrange iio trigger get and register
+    - iio:accel:kxcjk-1013: rearrange iio trigger get and register
+    - iio:accel:bma180: rearrange iio trigger get and register
+    - iio:accel:mxc4005: rearrange iio trigger get and register
+    - iio: accel: mma8452: ignore the return value of reset operation
+    - iio: gyro: mpu3050: Fix the error handling in mpu3050_power_up()
+    - iio: trigger: sysfs: fix use-after-free on remove
+    - iio: adc: stm32: fix maximum clock rate for stm32mp15x
+    - iio: imu: inv_icm42600: Fix broken icm42600 (chip id 0 value)
+    - iio: afe: rescale: Fix boolean logic bug
+    - iio: adc: stm32: Fix ADCs iteration in irq handler
+    - iio: adc: stm32: Fix IRQs on STM32F4 by removing custom spurious IRQs
+      message
+    - iio: adc: axp288: Override TS pin bias current for some models
+    - iio: adc: rzg2l_adc: add missing fwnode_handle_put() in
+      rzg2l_adc_parse_properties()
+    - iio: adc: adi-axi-adc: Fix refcount leak in adi_axi_adc_attach_client
+    - iio: adc: ti-ads131e08: add missing fwnode_handle_put() in
+      ads131e08_alloc_channels()
+    - xtensa: xtfpga: Fix refcount leak bug in setup
+    - xtensa: Fix refcount leak bug in time.c
+    - parisc/stifb: Fix fb_is_primary_device() only available with CONFIG_FB_STI
+    - parisc: Enable ARCH_HAS_STRICT_MODULE_RWX
+    - powerpc/microwatt: wire up rng during setup_arch()
+    - powerpc: Enable execve syscall exit tracepoint
+    - powerpc/rtas: Allow ibm,platform-dump RTAS call with null buffer address
+    - powerpc/powernv: wire up rng during setup_arch
+    - drm/msm/dp: Always clear mask bits to disable interrupts at
+      dp_ctrl_reset_irq_ctrl()
+    - ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node
+    - ARM: dts: imx6qdl: correct PU regulator ramp delay
+    - arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode
+    - ARM: exynos: Fix refcount leak in exynos_map_pmu
+    - soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe
+    - ARM: Fix refcount leak in axxia_boot_secondary
+    - memory: samsung: exynos5422-dmc: Fix refcount leak in of_get_dram_timings
+    - ARM: cns3xxx: Fix refcount leak in cns3xxx_init
+    - modpost: fix section mismatch check for exported init/exit sections
+    - ARM: dts: bcm2711-rpi-400: Fix GPIO line names
+    - random: update comment from copy_to_user() -> copy_to_iter()
+    - perf build-id: Fix caching files with a wrong build ID
+    - dma-direct: use the correct size for dma_set_encrypted()
+    - kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS (2nd attempt)
+    - powerpc/pseries: wire up rng during setup_arch()
+    - Linux 5.15.51
+  * Jammy update: v5.15.50 upstream stable release (LP: #1986715)
+    - net: mana: Add handling of CQE_RX_TRUNCATED
+    - zonefs: fix zonefs_iomap_begin() for reads
+    - usb: gadget: u_ether: fix regression in setting fixed MAC address
+    - bpf: Fix calling global functions from BPF_PROG_TYPE_EXT programs
+    - selftests/bpf: Add selftest for calling global functions from freplace
+    - serial: core: Initialize rs485 RTS polarity already on probe
+    - arm64: mm: Don't invalidate FROM_DEVICE buffers at start of DMA transfer
+    - Linux 5.15.50
+  * Jammy update: v5.15.49 upstream stable release (LP: #1983149)
+    - Revert "drm/amd/display: Fix DCN3 B0 DP Alt Mapping"
+    - nfsd: Replace use of rwsem with errseq_t
+    - arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3
+    - arm64: dts: imx8mn-beacon: Enable RTS-CTS on UART3
+    - powerpc/kasan: Silence KASAN warnings in __get_wchan()
+    - ASoC: nau8822: Add operation for internal PLL off and on
+    - drm/amd/display: Read Golden Settings Table from VBIOS
+    - drm/amdkfd: Use mmget_not_zero in MMU notifier
+    - dma-debug: make things less spammy under memory pressure
+    - ASoC: cs42l52: Fix TLV scales for mixer controls
+    - ASoC: cs35l36: Update digital volume TLV
+    - ASoC: cs53l30: Correct number of volume levels on SX controls
+    - ASoC: cs42l52: Correct TLV for Bypass Volume
+    - ASoC: cs42l56: Correct typo in minimum level for SX volume controls
+    - ASoC: cs42l51: Correct minimum value for SX volume control
+    - drm/amdkfd: add pinned BOs to kfd_bo_list
+    - ata: libata-core: fix NULL pointer deref in ata_host_alloc_pinfo()
+    - quota: Prevent memory allocation recursion while holding dq_lock
+    - ASoC: wm8962: Fix suspend while playing music
+    - ASoC: es8328: Fix event generation for deemphasis control
+    - ASoC: wm_adsp: Fix event generation for wm_adsp_fw_put()
+    - Input: soc_button_array - also add Lenovo Yoga Tablet2 1051F to
+      dmi_use_low_level_irq
+    - scsi: vmw_pvscsi: Expand vcpuHint to 16 bits
+    - scsi: lpfc: Resolve NULL ptr dereference after an ELS LOGO is aborted
+    - scsi: lpfc: Fix port stuck in bypassed state after LIP in PT2PT topology
+    - scsi: lpfc: Allow reduced polling rate for nvme_admin_async_event cmd
+      completion
+    - scsi: mpt3sas: Fix out-of-bounds compiler warning
+    - scsi: ipr: Fix missing/incorrect resource cleanup in error case
+    - scsi: pmcraid: Fix missing resource cleanup in error case
+    - ALSA: hda/realtek - Add HW8326 support
+    - virtio-mmio: fix missing put_device() when vm_cmdline_parent registration
+      failed
+    - nfc: nfcmrvl: Fix memory leak in nfcmrvl_play_deferred
+    - ipv6: Fix signed integer overflow in l2tp_ip6_sendmsg
+    - net: ethernet: mtk_eth_soc: fix misuse of mem alloc interface
+      netdev[napi]_alloc_frag
+    - gcc-12: disable '-Wdangling-pointer' warning for now
+    - mellanox: mlx5: avoid uninitialized variable warning with gcc-12
+    - MIPS: Loongson-3: fix compile mips cpu_hwmon as module build error.
+    - random: credit cpu and bootloader seeds by default
+    - gpio: dwapb: Don't print error on -EPROBE_DEFER
+    - platform/x86: gigabyte-wmi: Add Z690M AORUS ELITE AX DDR4 support
+    - platform/x86: gigabyte-wmi: Add support for B450M DS3H-CF
+    - platform/x86/intel: hid: Add Surface Go to VGBS allow list
+    - staging: r8188eu: fix rtw_alloc_hwxmits error detection for now
+    - staging: r8188eu: Use zeroing allocator in wpa_set_encryption()
+    - staging: r8188eu: Fix warning of array overflow in ioctl_linux.c
+    - pNFS: Don't keep retrying if the server replied NFS4ERR_LAYOUTUNAVAILABLE
+    - pNFS: Avoid a live lock condition in pnfs_update_layout()
+    - sunrpc: set cl_max_connect when cloning an rpc_clnt
+    - clocksource: hyper-v: unexport __init-annotated hv_init_clocksource()
+    - i40e: Fix adding ADQ filter to TC0
+    - i40e: Fix calculating the number of queue pairs
+    - i40e: Fix call trace in setup_tx_descriptors
+    - Drivers: hv: vmbus: Release cpu lock in error case
+    - tty: goldfish: Fix free_irq() on remove
+    - misc: atmel-ssc: Fix IRQ check in ssc_probe
+    - io_uring: fix races with file table unregister
+    - io_uring: fix races with buffer table unregister
+    - drm/i915/reset: Fix error_state_read ptr + offset use
+    - net: hns3: split function hclge_update_port_base_vlan_cfg()
+    - net: hns3: set port base vlan tbl_sta to false before removing old vlan
+    - net: hns3: don't push link state to VF if unalive
+    - net: hns3: fix tm port shapping of fibre port is incorrect after driver
+      initialization
+    - nvme: add device name to warning in uuid_show()
+    - mlxsw: spectrum_cnt: Reorder counter pools
+    - net: bgmac: Fix an erroneous kfree() in bgmac_remove()
+    - net: ax25: Fix deadlock caused by skb_recv_datagram in ax25_recvmsg
+    - arm64: ftrace: fix branch range checks
+    - arm64: ftrace: consistently handle PLTs.
+    - certs/blacklist_hashes.c: fix const confusion in certs blacklist
+    - init: Initialize noop_backing_dev_info early
+    - block: Fix handling of offline queues in blk_mq_alloc_request_hctx()
+    - faddr2line: Fix overlapping text section failures, the sequel
+    - i2c: npcm7xx: Add check for platform_driver_register
+    - irqchip/gic/realview: Fix refcount leak in realview_gic_of_init
+    - irqchip/gic-v3: Fix error handling in gic_populate_ppi_partitions
+    - irqchip/gic-v3: Fix refcount leak in gic_populate_ppi_partitions
+    - irqchip/realtek-rtl: Fix refcount leak in map_interrupts
+    - sched: Fix balance_push() vs __sched_setscheduler()
+    - i2c: designware: Use standard optional ref clock implementation
+    - mei: hbm: drop capability response on early shutdown
+    - mei: me: add raptor lake point S DID
+    - comedi: vmk80xx: fix expression for tx buffer size
+    - [Config] updateconfigs for LIB_MEMNEQ
+    - crypto: memneq - move into lib/
+    - USB: serial: option: add support for Cinterion MV31 with new baseline
+    - USB: serial: io_ti: add Agilent E5805A support
+    - usb: dwc2: Fix memory leak in dwc2_hcd_init
+    - usb: cdnsp: Fixed setting last_trb incorrectly
+    - usb: gadget: lpc32xx_udc: Fix refcount leak in lpc32xx_udc_probe
+    - usb: gadget: f_fs: change ep->status safe in ffs_epfile_io()
+    - usb: gadget: f_fs: change ep->ep safe in ffs_epfile_io()
+    - tty: n_gsm: Debug output allocation must use GFP_ATOMIC
+    - serial: 8250: Store to lsr_save_flags after lsr read
+    - bus: fsl-mc-bus: fix KASAN use-after-free in fsl_mc_bus_remove()
+    - dm mirror log: round up region bitmap size to BITS_PER_LONG
+    - drm/amd/display: Cap OLED brightness per max frame-average luminance
+    - cfi: Fix __cfi_slowpath_diag RCU usage with cpuidle
+    - ext4: fix super block checksum incorrect after mount
+    - ext4: fix bug_on ext4_mb_use_inode_pa
+    - ext4: make variable "count" signed
+    - ext4: add reserved GDT blocks check
+    - KVM: arm64: Don't read a HW interrupt pending state in user context
+    - virtio-pci: Remove wrong address verification in vp_del_vqs()
+    - powerpc/book3e: get rid of #include <generated/compile.h>
+    - clk: imx8mp: fix usb_root_clk parent
+    - Linux 5.15.49
+  * Jammy update: v5.15.48 upstream stable release (LP: #1983146)
+    - Linux 5.15.48
+    - Upstream stable to v5.15.48
+  * Jammy update: v5.15.47 upstream stable release (LP: #1982968)
+    - pcmcia: db1xxx_ss: restrict to MIPS_DB1XXX boards
+    - staging: greybus: codecs: fix type confusion of list iterator variable
+    - iio: adc: ad7124: Remove shift from scan_type
+    - lkdtm/bugs: Check for the NULL pointer after calling kmalloc
+    - lkdtm/bugs: Don't expect thread termination without CONFIG_UBSAN_TRAP
+    - tty: goldfish: Use tty_port_destroy() to destroy port
+    - tty: serial: owl: Fix missing clk_disable_unprepare() in owl_uart_probe
+    - tty: n_tty: Restore EOF push handling behavior
+    - serial: 8250_aspeed_vuart: Fix potential NULL dereference in
+      aspeed_vuart_probe
+    - tty: serial: fsl_lpuart: fix potential bug when using both of_alias_get_id
+      and ida_simple_get
+    - remoteproc: imx_rproc: Ignore create mem entry for resource table
+    - usb: usbip: fix a refcount leak in stub_probe()
+    - usb: usbip: add missing device lock on tweak configuration cmd
+    - USB: storage: karma: fix rio_karma_init return
+    - usb: musb: Fix missing of_node_put() in omap2430_probe
+    - staging: fieldbus: Fix the error handling path in
+      anybuss_host_common_probe()
+    - pwm: lp3943: Fix duty calculation in case period was clamped
+    - pwm: raspberrypi-poe: Fix endianness in firmware struct
+    - rpmsg: qcom_smd: Fix irq_of_parse_and_map() return value
+    - usb: dwc3: gadget: Replace list_for_each_entry_safe() if using giveback
+    - usb: dwc3: pci: Fix pm_runtime_get_sync() error checking
+    - misc: fastrpc: fix an incorrect NULL check on list iterator
+    - firmware: stratix10-svc: fix a missing check on list iterator
+    - usb: typec: mux: Check dev_set_name() return value
+    - rpmsg: virtio: Fix possible double free in rpmsg_probe()
+    - rpmsg: virtio: Fix possible double free in rpmsg_virtio_add_ctrl_dev()
+    - rpmsg: virtio: Fix the unregistration of the device rpmsg_ctrl
+    - iio: adc: stmpe-adc: Fix wait_for_completion_timeout return value check
+    - iio: proximity: vl53l0x: Fix return value check of
+      wait_for_completion_timeout
+    - iio: adc: sc27xx: fix read big scale voltage not right
+    - iio: adc: sc27xx: Fine tune the scale calibration values
+    - rpmsg: qcom_smd: Fix returning 0 if irq_of_parse_and_map() fails
+    - pvpanic: Fix typos in the comments
+    - misc/pvpanic: Convert regular spinlock into trylock on panic path
+    - phy: qcom-qmp: fix pipe-clock imbalance on power-on failure
+    - power: supply: axp288_fuel_gauge: Drop BIOS version check from "T3 MRD" DMI
+      quirk
+    - serial: sifive: Report actual baud base rather than fixed 115200
+    - export: fix string handling of namespace in EXPORT_SYMBOL_NS
+    - soundwire: intel: prevent pm_runtime resume prior to system suspend
+    - coresight: cpu-debug: Replace mutex with mutex_trylock on panic notifier
+    - ksmbd: fix reference count leak in smb_check_perm_dacl()
+    - extcon: ptn5150: Add queue work sync before driver release
+    - soc: rockchip: Fix refcount leak in rockchip_grf_init
+    - clocksource/drivers/riscv: Events are stopped during CPU suspend
+    - ARM: dts: aspeed: ast2600-evb: Enable RX delay for MAC0/MAC1
+    - rtc: mt6397: check return value after calling platform_get_resource()
+    - rtc: ftrtc010: Use platform_get_irq() to get the interrupt
+    - rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
+    - staging: r8188eu: add check for kzalloc
+    - tty: n_gsm: Don't ignore write return value in gsmld_output()
+    - tty: n_gsm: Fix packet data hex dump output
+    - serial: meson: acquire port->lock in startup()
+    - serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
+    - serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
+    - serial: digicolor-usart: Don't allow CS5-6
+    - serial: rda-uart: Don't allow CS5-6
+    - serial: txx9: Don't allow CS5-6
+    - serial: sh-sci: Don't allow CS5-6
+    - serial: sifive: Sanitize CSIZE and c_iflag
+    - serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
+    - serial: stm32-usart: Correct CSIZE, bits, and parity
+    - firmware: dmi-sysfs: Fix memory leak in dmi_sysfs_register_handle
+    - bus: ti-sysc: Fix warnings for unbind for serial
+    - driver: base: fix UAF when driver_attach failed
+    - driver core: fix deadlock in __device_attach
+    - watchdog: rti-wdt: Fix pm_runtime_get_sync() error checking
+    - watchdog: ts4800_wdt: Fix refcount leak in ts4800_wdt_probe
+    - blk-mq: don't touch ->tagset in blk_mq_get_sq_hctx
+    - ASoC: fsl_sai: Fix FSL_SAI_xDR/xFR definition
+    - clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
+    - s390/crypto: fix scatterwalk_unmap() callers in AES-GCM
+    - net: sched: fixed barrier to prevent skbuff sticking in qdisc backlog
+    - net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry()
+    - net: ethernet: ti: am65-cpsw-nuss: Fix some refcount leaks
+    - net: dsa: mv88e6xxx: Fix refcount leak in mv88e6xxx_mdios_register
+    - modpost: fix removing numeric suffixes
+    - jffs2: fix memory leak in jffs2_do_fill_super
+    - ubi: fastmap: Fix high cpu usage of ubi_bgt by making sure wl_pool not empty
+    - ubi: ubi_create_volume: Fix use-after-free when volume creation failed
+    - selftests/bpf: fix selftest after random: Urandom_read tracepoint removal
+    - selftests/bpf: fix stacktrace_build_id with missing kprobe/urandom_read
+    - bpf: Fix probe read error in ___bpf_prog_run()
+    - block: take destination bvec offsets into account in bio_copy_data_iter
+    - riscv: read-only pages should not be writable
+    - net/smc: fixes for converting from "struct smc_cdc_tx_pend **" to "struct
+      smc_wr_tx_pend_priv *"
+    - tcp: add accessors to read/set tp->snd_cwnd
+    - nfp: only report pause frame configuration for physical device
+    - sfc: fix considering that all channels have TX queues
+    - sfc: fix wrong tx channel offset with efx_separate_tx_channels
+    - block: make bioset_exit() fully resilient against being called twice
+    - vdpa: Fix error logic in vdpa_nl_cmd_dev_get_doit
+    - virtio: pci: Fix an error handling path in vp_modern_probe()
+    - net/mlx5: Don't use already freed action pointer
+    - net/mlx5: CT: Fix header-rewrite re-use for tupels
+    - net/mlx5: correct ECE offset in query qp output
+    - net/mlx5e: Update netdev features after changing XDP state
+    - net: sched: add barrier to fix packet stuck problem for lockless qdisc
+    - tcp: tcp_rtx_synack() can be called from process context
+    - vdpa: ifcvf: set pci driver data in probe
+    - octeontx2-af: fix error code in is_valid_offset()
+    - s390/mcck: isolate SIE instruction when setting CIF_MCCK_GUEST flag
+    - regulator: mt6315-regulator: fix invalid allowed mode
+    - gpio: pca953x: use the correct register address to do regcache sync
+    - afs: Fix infinite loop found by xfstest generic/676
+    - scsi: sd: Fix potential NULL pointer dereference
+    - tipc: check attribute length for bearer name
+    - driver core: Fix wait_for_device_probe() & deferred_probe_timeout
+      interaction
+    - perf c2c: Fix sorting in percent_rmt_hitm_cmp()
+    - dmaengine: idxd: set DMA_INTERRUPT cap bit
+    - mips: cpc: Fix refcount leak in mips_cpc_default_phys_base
+    - bootconfig: Make the bootconfig.o as a normal object file
+    - tracing: Make tp_printk work on syscall tracepoints
+    - tracing: Fix sleeping function called from invalid context on RT kernel
+    - tracing: Avoid adding tracer option before update_tracer_options
+    - iommu/arm-smmu: fix possible null-ptr-deref in arm_smmu_device_probe()
+    - iommu/arm-smmu-v3: check return value after calling platform_get_resource()
+    - f2fs: remove WARN_ON in f2fs_is_valid_blkaddr
+    - i2c: cadence: Increase timeout per message if necessary
+    - m68knommu: set ZERO_PAGE() to the allocated zeroed page
+    - m68knommu: fix undefined reference to `_init_sp'
+    - dmaengine: zynqmp_dma: In struct zynqmp_dma_chan fix desc_size data type
+    - NFSv4: Don't hold the layoutget locks across multiple RPC calls
+    - video: fbdev: hyperv_fb: Allow resolutions with size > 64 MB for Gen1
+    - video: fbdev: pxa3xx-gcu: release the resources correctly in
+      pxa3xx_gcu_probe/remove()
+    - RISC-V: use memcpy for kexec_file mode
+    - m68knommu: fix undefined reference to `mach_get_rtc_pll'
+    - f2fs: fix to tag gcing flag on page during file defragment
+    - xprtrdma: treat all calls not a bcall when bc_serv is NULL
+    - drm/bridge: sn65dsi83: Fix an error handling path in sn65dsi83_probe()
+    - drm/bridge: ti-sn65dsi83: Handle dsi_lanes == 0 as invalid
+    - netfilter: nat: really support inet nat without l3 address
+    - netfilter: nf_tables: use kfree_rcu(ptr, rcu) to release hooks in clean_net
+      path
+    - netfilter: nf_tables: delete flowtable hooks via transaction list
+    - powerpc/kasan: Force thread size increase with KASAN
+    - SUNRPC: Trap RDMA segment overflows
+    - netfilter: nf_tables: always initialize flowtable hook list in transaction
+    - ata: pata_octeon_cf: Fix refcount leak in octeon_cf_probe
+    - netfilter: nf_tables: release new hooks on unsupported flowtable flags
+    - netfilter: nf_tables: memleak flow rule from commit path
+    - netfilter: nf_tables: bail out early if hardware offload is not supported
+    - xen: unexport __init-annotated xen_xlate_map_ballooned_pages()
+    - stmmac: intel: Fix an error handling path in intel_eth_pci_probe()
+    - af_unix: Fix a data-race in unix_dgram_peer_wake_me().
+    - bpf, arm64: Clear prog->jited_len along prog->jited
+    - net: dsa: lantiq_gswip: Fix refcount leak in gswip_gphy_fw_list
+    - net/mlx4_en: Fix wrong return value on ioctl EEPROM query failure
+    - i40e: xsk: Move tmp desc array from driver to pool
+    - xsk: Fix handling of invalid descriptors in XSK TX batching API
+    - SUNRPC: Fix the calculation of xdr->end in xdr_get_next_encode_buffer()
+    - net: mdio: unexport __init-annotated mdio_bus_init()
+    - net: xfrm: unexport __init-annotated xfrm4_protocol_init()
+    - net: ipv6: unexport __init-annotated seg6_hmac_init()
+    - net/mlx5: Lag, filter non compatible devices
+    - net/mlx5: Fix mlx5_get_next_dev() peer device matching
+    - net/mlx5: Rearm the FW tracer after each tracer event
+    - net/mlx5: fs, fail conflicting actions
+    - ip_gre: test csum_start instead of transport header
+    - net: altera: Fix refcount leak in altera_tse_mdio_create
+    - net: dsa: mv88e6xxx: use BMSR_ANEGCOMPLETE bit for filling an_complete
+    - tcp: use alloc_large_system_hash() to allocate table_perturb
+    - drm: imx: fix compiler warning with gcc-12
+    - nfp: flower: restructure flow-key for gre+vlan combination
+    - iov_iter: Fix iter_xarray_get_pages{,_alloc}()
+    - iio: dummy: iio_simple_dummy: check the return value of kstrdup()
+    - staging: rtl8712: fix a potential memory leak in r871xu_drv_init()
+    - iio: st_sensors: Add a local lock for protecting odr
+    - lkdtm/usercopy: Expand size of "out of frame" object
+    - drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback()
+    - drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()
+    - tty: synclink_gt: Fix null-pointer-dereference in slgt_clean()
+    - tty: Fix a possible resource leak in icom_probe
+    - thunderbolt: Use different lane for second DisplayPort tunnel
+    - drivers: staging: rtl8192u: Fix deadlock in ieee80211_beacons_stop()
+    - drivers: staging: rtl8192e: Fix deadlock in rtllib_beacons_stop()
+    - USB: host: isp116x: check return value after calling platform_get_resource()
+    - drivers: tty: serial: Fix deadlock in sa1100_set_termios()
+    - drivers: usb: host: Fix deadlock in oxu_bus_suspend()
+    - USB: hcd-pci: Fully suspend across freeze/thaw cycle
+    - char: xillybus: fix a refcount leak in cleanup_dev()
+    - sysrq: do not omit current cpu when showing backtrace of all active CPUs
+    - usb: dwc2: gadget: don't reset gadget's driver->bus
+    - soundwire: qcom: adjust autoenumeration timeout
+    - misc: rtsx: set NULL intfdata when probe fails
+    - extcon: Fix extcon_get_extcon_dev() error handling
+    - extcon: Modify extcon device to be created after driver data is set
+    - clocksource/drivers/sp804: Avoid error on multiple instances
+    - staging: rtl8712: fix uninit-value in usb_read8() and friends
+    - staging: rtl8712: fix uninit-value in r871xu_drv_init()
+    - serial: msm_serial: disable interrupts in __msm_console_write()
+    - kernfs: Separate kernfs_pr_cont_buf and rename_lock.
+    - watchdog: wdat_wdt: Stop watchdog when rebooting the system
+    - md: protect md_unregister_thread from reentrancy
+    - scsi: myrb: Fix up null pointer access on myrb_cleanup()
+    - ceph: allow ceph.dir.rctime xattr to be updatable
+    - ceph: flush the mdlog for filesystem sync
+    - drm/amd/display: Check if modulo is 0 before dividing.
+    - drm/radeon: fix a possible null pointer dereference
+    - drm/amd/pm: Fix missing thermal throttler status
+    - um: line: Use separate IRQs per line
+    - modpost: fix undefined behavior of is_arm_mapping_symbol()
+    - x86/cpu: Elide KCSAN for cpu_has() and friends
+    - jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
+    - nbd: call genl_unregister_family() first in nbd_cleanup()
+    - nbd: fix race between nbd_alloc_config() and module removal
+    - cifs: version operations for smb20 unneeded when legacy support disabled
+    - drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
+    - nodemask: Fix return values to be unsigned
+    - vringh: Fix loop descriptors check in the indirect cases
+    - scripts/gdb: change kernel config dumping method
+    - ALSA: usb-audio: Skip generic sync EP parse for secondary EP
+    - ALSA: usb-audio: Set up (implicit) sync for Saffire 6
+    - ALSA: hda/conexant - Fix loopback issue with CX20632
+    - ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo Yoga
+      DuetITL 2021
+    - ALSA: hda/realtek: Add quirk for HP Dev One
+    - cifs: return errors during session setup during reconnects
+    - cifs: fix reconnect on smb3 mount types
+    - KEYS: trusted: tpm2: Fix migratable logic
+    - ata: libata-transport: fix {dma|pio|xfer}_mode sysfs files
+    - mmc: block: Fix CQE recovery reset success
+    - net: phy: dp83867: retrigger SGMII AN when link change
+    - writeback: Fix inode->i_io_list not be protected by inode->i_lock error
+    - nfc: st21nfca: fix incorrect validating logic in EVT_TRANSACTION
+    - nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
+    - nfc: st21nfca: fix incorrect sizing calculations in EVT_TRANSACTION
+    - ixgbe: fix bcast packets Rx on VF after promisc removal
+    - ixgbe: fix unexpected VLAN Rx in promisc mode on VF
+    - Input: bcm5974 - set missing URB_NO_TRANSFER_DMA_MAP urb flag
+    - vduse: Fix NULL pointer dereference on sysfs access
+    - powerpc: Don't select HAVE_IRQ_EXIT_ON_IRQ_STACK
+    - drm/bridge: analogix_dp: Support PSR-exit to disable transition
+    - drm/atomic: Force bridge self-refresh-exit on CRTC switch
+    - drm/amdgpu: update VCN codec support for Yellow Carp
+    - powerpc/32: Fix overread/overwrite of thread_struct via ptrace
+    - powerpc/mm: Switch obsolete dssall to .long
+    - drm/ast: Create threshold values for AST2600
+    - random: avoid checking crng_ready() twice in random_init()
+    - random: mark bootloader randomness code as __init
+    - random: account for arch randomness in bits
+    - md/raid0: Ignore RAID0 layout if the second zone has only one device
+    - net/sched: act_police: more accurate MTU policing
+    - PCI: qcom: Fix pipe clock imbalance
+    - zonefs: fix handling of explicit_open option on mount
+    - iov_iter: fix build issue due to possible type mis-match
+    - dmaengine: idxd: add missing callback function to support DMA_INTERRUPT
+    - tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd
+    - xsk: Fix possible crash when multiple sockets are created
+    - Linux 5.15.47
+  * CVE-2022-36946
+    - netfilter: nf_queue: do not allow packet truncation below transport header
+      offset
+  * CVE-2021-33655
+    - fbcon: Disallow setting font bigger than screen size
+    - fbcon: Prevent that screen size is smaller than font size
+    - fbmem: Check virtual screen sizes in fb_set_var()
+
+  [ Ubuntu: 5.15.0-47.51 ]
+
+  * jammy/linux: 5.15.0-47.51 -proposed tracker (LP: #1983903)
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - UBUNTU: [Packaging] Move python3-dev to build-depends
+  * touchpad and touchscreen doesn't work at all on ACER Spin 5 (SP513-54N)
+    (LP: #1884232)
+    - x86/PCI: Eliminate remove_e820_regions() common subexpressions
+    - x86: Log resource clipping for E820 regions
+    - x86/PCI: Clip only host bridge windows for E820 regions
+    - x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
+    - x86/PCI: Disable E820 reserved region clipping via quirks
+    - x86/PCI: Revert "x86/PCI: Clip only host bridge windows for E820 regions"
+  * [SRU][H/OEM-5.13/OEM-5.14/U][J/OEM-5.17/U] Fix invalid MAC address after
+    hotplug tbt dock (LP: #1942999)
+    - SAUCE: igc: wait for the MAC copy when enabled MAC passthrough
+  * Mass Storage Gadget driver truncates device >2TB (LP: #1981390)
+    - usb: gadget: storage: add support for media larger than 2T
+  * AMD Rembrandt: DP tunneling fails with Thunderbolt monitors (LP: #1983143)
+    - SAUCE: drm/amd: Fix DP Tunneling with Thunderbolt monitors
+    - drm/amd/display: Fix for dmub outbox notification enable
+    - Revert "drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset"
+    - drm/amd/display: Reset link encoder assignments for GPU reset
+    - drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset
+    - drm/amd/display: Fix new dmub notification enabling in DM
+    - SAUCE: thunderbolt: Add DP out resource when DP tunnel is discovered.
+  * Fix sub-optimal I210 network speed (LP: #1976438)
+    - igb: Make DMA faster when CPU is active on the PCIe link
+  * e1000e report hardware hang (LP: #1973104)
+    - e1000e: Enable GPT clock before sending message to CSME
+    - Revert "e1000e: Fix possible HW unit hang after an s0ix exit"
+  * ioam6.sh in net from ubuntu_kernel_selftests fails with 5.15 kernels in
+    Focal (LP: #1982930)
+    - selftests: net: fix IOAM test skip return code
+  * Additional fix for TGL + AUO panel flickering (LP: #1983297)
+    - Revert "UBUNTU: SAUCE: drm/i915/display/psr: Fix flicker on TGL + AUO panel"
+    - drm/i915/display: Fix sel fetch plane offset calculation
+    - drm/i915: Nuke ORIGIN_GTT
+    - drm/i915/display: Drop PSR support from HSW and BDW
+    - drm/i915/display/psr: Handle plane and pipe restrictions at every page flip
+    - drm/i915/display/psr: Do full fetch when handling multi-planar formats
+    - drm/i915/display: Drop unnecessary frontbuffer flushes
+    - drm/i915/display: Handle frontbuffer rendering when PSR2 selective fetch is
+      enabled
+    - drm/i915/display: Fix glitches when moving cursor with PSR2 selective fetch
+      enabled
+    - SAUCE: drm/i915/display/psr: Reinstate fix for TGL + AUO panel flicker
+  * AMD Yellow Carp DMCUB fw update for s0i3 B0 fixes (LP: #1957026)
+    - drm/amd/display: Optimize bandwidth on following fast update
+    - drm/amd/display: Fix surface optimization regression on Carrizo
+    - drm/amd/display: Reset DMCUB before HW init
+  * GPIO character device v1 API not enabled in kernel (LP: #1953613)
+    - [Config] Enable CONFIG_GPIO_CDEV_V1
+  * intel_iommu: Fix  enable intel_iommu, Ubuntu 22.04 installation crashes
+    (LP: #1982104)
+    - iommu/vt-d: Fix RID2PASID setup/teardown failure
+  * Headset mic with Cirrus logic codec doesn't work (LP: #1972815)
+    - ASoC: cs42l42: Move CS42L42 register descriptions to general include
+    - ALSA: hda/cs8409: Use general cs42l42 include in cs8409 hda driver
+    - ALSA: hda/cs8409: Support manual mode detection for CS42L42
+  * Failed to resume from S3 blocked by atlantic driver[1d6a:94c0]
+    (LP: #1981950)
+    - net: atlantic: remove deep parameter on suspend/resume functions
+    - net: atlantic: remove aq_nic_deinit() when resume
+  * Make cm32181 sensor work after system suspend (LP: #1981773)
+    - iio: light: cm32181: Add PM support
+  * Clear PCI errors left from BIOS (LP: #1981173)
+    - PCI: Clear PCI_STATUS when setting up device
+  * Fix AMDGPU blank screen when Type-C DP alt is in use (LP: #1980060)
+    - drm/amd/display: Query DMCUB for dp alt status
+    - drm/amd/display: Add version check before using DP alt query interface
+  * Fix WD22TB4 suspend and resume, two external monitor can not output
+    (LP: #1979267)
+    - drm/dp/mst: Read the extended DPCD capabilities during system resume
+  * [SRU] bcache deadlock during read IO in writeback mode (LP: #1980925)
+    - bcache: memset on stack variables in bch_btree_check() and
+      bch_sectors_dirty_init()
+  * Audio mute key (f5) LED and Mic mute key (f8) LED are no function on HP
+    440/450/640/650 G9 (LP: #1982716)
+    - ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
+  * Enable WiFi hotspot feature for MediaTek MT7921 (LP: #1979173)
+    - mt76: mt7921: Add AP mode support
+    - mt76: mt7921: not support beacon offload disable command
+    - mt76: mt7921: fix command timeout in AP stop period
+  * Fix drm/amd/pm: enable ASPM by default (LP: #1966680)
+    - drm/amd: Refactor `amdgpu_aspm` to be evaluated per device
+    - drm/amd: Use amdgpu_device_should_use_aspm on navi umd pstate switching
+    - drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems
+  * Power cycle USB ports on shutdown/reboot (LP: #1976503)
+    - xhci: turn off port power in shutdown
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - binfmt_flat: do not stop relocating GOT entries prematurely on riscv
+    - parisc/stifb: Implement fb_is_primary_device()
+    - parisc/stifb: Keep track of hardware path of graphics card
+    - RISC-V: Mark IORESOURCE_EXCLUSIVE for reserved mem instead of
+      IORESOURCE_BUSY
+    - riscv: Initialize thread pointer before calling C functions
+    - riscv: Fix irq_work when SMP is disabled
+    - riscv: Wire up memfd_secret in UAPI header
+    - riscv: Move alternative length validation into subsection
+    - ALSA: hda/realtek - Add new type for ALC245
+    - ALSA: hda/realtek: Enable 4-speaker output for Dell XPS 15 9520 laptop
+    - ALSA: hda/realtek - Fix microphone noise on ASUS TUF B550M-PLUS
+    - ALSA: usb-audio: Cancel pending work at closing a MIDI substream
+    - USB: serial: option: add Quectel BG95 modem
+    - USB: new quirk for Dell Gen 2 devices
+    - usb: isp1760: Fix out-of-bounds array access
+    - usb: dwc3: gadget: Move null pinter check to proper place
+    - usb: core: hcd: Add support for deferring roothub registration
+    - fs/ntfs3: Update valid size if -EIOCBQUEUED
+    - fs/ntfs3: Fix fiemap + fix shrink file size (to remove preallocated space)
+    - fs/ntfs3: Keep preallocated only if option prealloc enabled
+    - fs/ntfs3: Check new size for limits
+    - fs/ntfs3: In function ntfs_set_acl_ex do not change inode->i_mode if called
+      from function ntfs_init_acl
+    - fs/ntfs3: Fix some memory leaks in an error handling path of 'log_replay()'
+    - fs/ntfs3: Update i_ctime when xattr is added
+    - fs/ntfs3: Restore ntfs_xattr_get_acl and ntfs_xattr_set_acl functions
+    - cifs: fix potential double free during failed mount
+    - cifs: when extending a file with falloc we should make files not-sparse
+    - xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
+    - platform/x86: intel-hid: fix _DSM function index handling
+    - x86/MCE/AMD: Fix memory leak when threshold_create_bank() fails
+    - perf/x86/intel: Fix event constraints for ICL
+    - x86/kexec: fix memory leak of elf header buffer
+    - x86/sgx: Set active memcg prior to shmem allocation
+    - ptrace/um: Replace PT_DTRACE with TIF_SINGLESTEP
+    - ptrace/xtensa: Replace PT_SINGLESTEP with TIF_SINGLESTEP
+    - ptrace: Reimplement PTRACE_KILL by always sending SIGKILL
+    - btrfs: add "0x" prefix for unsupported optional features
+    - btrfs: return correct error number for __extent_writepage_io()
+    - btrfs: repair super block num_devices automatically
+    - btrfs: fix the error handling for submit_extent_page() for
+      btrfs_do_readpage()
+    - iommu/vt-d: Add RPLS to quirk list to skip TE disabling
+    - drm/vmwgfx: validate the screen formats
+    - drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes
+    - selftests/bpf: Fix vfs_link kprobe definition
+    - selftests/bpf: Fix parsing of prog types in UAPI hdr for bpftool sync
+    - mwifiex: add mutex lock for call in mwifiex_dfs_chan_sw_work_queue
+    - b43legacy: Fix assigning negative value to unsigned variable
+    - b43: Fix assigning negative value to unsigned variable
+    - ipw2x00: Fix potential NULL dereference in libipw_xmit()
+    - ipv6: fix locking issues with loops over idev->addr_list
+    - fbcon: Consistently protect deferred_takeover with console_lock()
+    - x86/platform/uv: Update TSC sync state for UV5
+    - ACPICA: Avoid cache flush inside virtual machines
+    - mac80211: minstrel_ht: fix where rate stats are stored (fixes debugfs
+      output)
+    - drm/komeda: return early if drm_universal_plane_init() fails.
+    - drm/amd/display: Disabling Z10 on DCN31
+    - rcu-tasks: Fix race in schedule and flush work
+    - rcu: Make TASKS_RUDE_RCU select IRQ_WORK
+    - sfc: ef10: Fix assigning negative value to unsigned variable
+    - ALSA: jack: Access input_dev under mutex
+    - spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA
+      direction
+    - tools/power turbostat: fix ICX DRAM power numbers
+    - scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg()
+    - scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock
+    - scsi: lpfc: Fix call trace observed during I/O with CMF enabled
+    - cpuidle: PSCI: Improve support for suspend-to-RAM for PSCI OSI mode
+    - drm/amd/pm: fix double free in si_parse_power_table()
+    - ASoC: rsnd: care default case on rsnd_ssiu_busif_err_status_clear()
+    - ASoC: rsnd: care return value from rsnd_node_fixed_index()
+    - ath9k: fix QCA9561 PA bias level
+    - media: venus: hfi: avoid null dereference in deinit
+    - media: pci: cx23885: Fix the error handling in cx23885_initdev()
+    - media: cx25821: Fix the warning when removing the module
+    - md/bitmap: don't set sb values if can't pass sanity check
+    - mmc: jz4740: Apply DMA engine limits to maximum segment size
+    - drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit
+    - scsi: megaraid: Fix error check return value of register_chrdev()
+    - drm/amdgpu/sdma: Fix incorrect calculations of the wptr of the doorbells
+    - scsi: ufs: Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync()
+    - scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp()
+    - ath11k: disable spectral scan during spectral deinit
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the HP Pro Tablet 408
+    - drm/plane: Move range check for format_count earlier
+    - drm/amd/pm: fix the compile warning
+    - ath10k: skip ath10k_halt during suspend for driver state RESTARTING
+    - arm64: compat: Do not treat syscall number as ESR_ELx for a bad syscall
+    - drm: msm: fix error check return value of irq_of_parse_and_map()
+    - scsi: target: tcmu: Fix possible data corruption
+    - ipv6: Don't send rs packets to the interface of ARPHRD_TUNNEL
+    - net/mlx5: fs, delete the FTE when there are no rules attached to it
+    - ASoC: dapm: Don't fold register value changes into notifications
+    - mlxsw: spectrum_dcb: Do not warn about priority changes
+    - mlxsw: Treat LLDP packets as control
+    - drm/amdgpu/psp: move PSP memory alloc from hw_init to sw_init
+    - drm/amdgpu/ucode: Remove firmware load type check in amdgpu_ucode_free_bo
+    - regulator: mt6315: Enforce regulator-compatible, not name
+    - HID: bigben: fix slab-out-of-bounds Write in bigben_probe
+    - of: Support more than one crash kernel regions for kexec -s
+    - ASoC: tscs454: Add endianness flag in snd_soc_component_driver
+    - scsi: lpfc: Alter FPIN stat accounting logic
+    - net: remove two BUG() from skb_checksum_help()
+    - s390/preempt: disable __preempt_count_add() optimization for
+      PROFILE_ALL_BRANCHES
+    - perf/amd/ibs: Cascade pmu init functions' return value
+    - sched/core: Avoid obvious double update_rq_clock warning
+    - spi: stm32-qspi: Fix wait_cmd timeout in APM mode
+    - dma-debug: change allocation mode from GFP_NOWAIT to GFP_ATIOMIC
+    - ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default
+    - ipmi:ssif: Check for NULL msg when handling events and messages
+    - ipmi: Fix pr_fmt to avoid compilation issues
+    - rtlwifi: Use pr_warn instead of WARN_ONCE
+    - mt76: mt7921: accept rx frames with non-standard VHT MCS10-11
+    - mt76: fix encap offload ethernet type check
+    - media: rga: fix possible memory leak in rga_probe
+    - media: coda: limit frame interval enumeration to supported encoder frame
+      sizes
+    - media: hantro: HEVC: unconditionnaly set pps_{cb/cr}_qp_offset values
+    - media: ccs-core.c: fix failure to call clk_disable_unprepare
+    - media: imon: reorganize serialization
+    - media: cec-adap.c: fix is_configuring state
+    - usbnet: Run unregister_netdev() before unbind() again
+    - openrisc: start CPU timer early in boot
+    - nvme-pci: fix a NULL pointer dereference in nvme_alloc_admin_tags
+    - ASoC: rt5645: Fix errorenous cleanup order
+    - nbd: Fix hung on disconnect request if socket is closed before
+    - drm/amd/pm: update smartshift powerboost calc for smu12
+    - drm/amd/pm: update smartshift powerboost calc for smu13
+    - net: phy: micrel: Allow probing without .driver_data
+    - media: exynos4-is: Fix compile warning
+    - media: hantro: Stop using H.264 parameter pic_num
+    - ASoC: max98357a: remove dependency on GPIOLIB
+    - ASoC: rt1015p: remove dependency on GPIOLIB
+    - ACPI: CPPC: Assume no transition latency if no PCCT
+    - nvme: set non-mdts limits in nvme_scan_work
+    - can: mcp251xfd: silence clang's -Wunaligned-access warning
+    - x86/microcode: Add explicit CPU vendor dependency
+    - net: ipa: ignore endianness if there is no header
+    - m68k: atari: Make Atari ROM port I/O write macros return void
+    - rxrpc: Return an error to sendmsg if call failed
+    - rxrpc, afs: Fix selection of abort codes
+    - afs: Adjust ACK interpretation to try and cope with NAT
+    - eth: tg3: silence the GCC 12 array-bounds warning
+    - char: tpm: cr50_i2c: Suppress duplicated error message in .remove()
+    - selftests/bpf: fix btf_dump/btf_dump due to recent clang change
+    - gfs2: use i_lock spin_lock for inode qadata
+    - scsi: target: tcmu: Avoid holding XArray lock when calling lock_page
+    - IB/rdmavt: add missing locks in rvt_ruc_loopback
+    - ARM: dts: ox820: align interrupt controller node name with dtschema
+    - ARM: dts: socfpga: align interrupt controller node name with dtschema
+    - ARM: dts: s5pv210: align DMA channels with dtschema
+    - arm64: dts: qcom: msm8994: Fix the cont_splash_mem address
+    - arm64: dts: qcom: msm8994: Fix BLSP[12]_DMA channels count
+    - PM / devfreq: rk3399_dmc: Disable edev on remove()
+    - crypto: ccree - use fine grained DMA mapping dir
+    - soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc
+    - fs: jfs: fix possible NULL pointer dereference in dbFree()
+    - arm64: dts: qcom: sdm845-xiaomi-beryllium: fix typo in panel's vddio-supply
+      property
+    - ALSA: usb-audio: Add quirk bits for enabling/disabling generic implicit fb
+    - ALSA: usb-audio: Move generic implicit fb quirk entries into quirks.c
+    - ARM: OMAP1: clock: Fix UART rate reporting algorithm
+    - powerpc/fadump: Fix fadump to work with a different endian capture kernel
+    - fat: add ratelimit to fat*_ent_bread()
+    - pinctrl: renesas: rzn1: Fix possible null-ptr-deref in
+      sh_pfc_map_resources()
+    - ARM: versatile: Add missing of_node_put in dcscb_init
+    - ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROM
+    - ARM: hisi: Add missing of_node_put after of_find_compatible_node
+    - cpufreq: Avoid unnecessary frequency updates due to mismatch
+    - powerpc/rtas: Keep MSR[RI] set when calling RTAS
+    - PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
+    - KVM: PPC: Book3S HV Nested: L2 LPCR should inherit L1 LPES setting
+    - alpha: fix alloc_zeroed_user_highpage_movable()
+    - tracing: incorrect isolate_mote_t cast in mm_vmscan_lru_isolate
+    - powerpc/powernv/vas: Assign real address to rx_fifo in vas_rx_win_attr
+    - powerpc/xics: fix refcount leak in icp_opal_init()
+    - powerpc/powernv: fix missing of_node_put in uv_init()
+    - macintosh/via-pmu: Fix build failure when CONFIG_INPUT is disabled
+    - powerpc/iommu: Add missing of_node_put in iommu_init_early_dart
+    - smb3: check for null tcon
+    - RDMA/hfi1: Prevent panic when SDMA is disabled
+    - Input: gpio-keys - cancel delayed work only in case of GPIO
+    - drm: fix EDID struct for old ARM OABI format
+    - drm/bridge_connector: enable HPD by default if supported
+    - dt-bindings: display: sitronix, st7735r: Fix backlight in example
+    - drm/vmwgfx: Fix an invalid read
+    - ath11k: acquire ab->base_lock in unassign when finding the peer by addr
+    - drm: bridge: it66121: Fix the register page length
+    - ath9k: fix ar9003_get_eepmisc
+    - drm/edid: fix invalid EDID extension block filtering
+    - drm/bridge: adv7511: clean up CEC adapter when probe fails
+    - drm: bridge: icn6211: Fix register layout
+    - drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling
+    - mtd: spinand: gigadevice: fix Quad IO for GD5F1GQ5UExxG
+    - spi: qcom-qspi: Add minItems to interconnect-names
+    - ASoC: mediatek: Fix error handling in mt8173_max98090_dev_probe
+    - ASoC: mediatek: Fix missing of_node_put in mt2701_wm8960_machine_probe
+    - x86/delay: Fix the wrong asm constraint in delay_loop()
+    - drm/vc4: hvs: Fix frame count register readout
+    - drm/mediatek: Fix mtk_cec_mask()
+    - drm/vc4: hvs: Reset muxes at probe time
+    - drm/vc4: txp: Don't set TXP_VSTART_AT_EOF
+    - drm/vc4: txp: Force alpha to be 0xff if it's disabled
+    - libbpf: Don't error out on CO-RE relos for overriden weak subprogs
+    - x86/PCI: Fix ALi M1487 (IBC) PIRQ router link value interpretation
+    - mptcp: reset the packet scheduler on PRIO change
+    - nl80211: show SSID for P2P_GO interfaces
+    - drm/komeda: Fix an undefined behavior bug in komeda_plane_add()
+    - drm: mali-dp: potential dereference of null pointer
+    - spi: spi-ti-qspi: Fix return value handling of wait_for_completion_timeout
+    - scftorture: Fix distribution of short handler delays
+    - net: dsa: mt7530: 1G can also support 1000BASE-X link mode
+    - ixp4xx_eth: fix error check return value of platform_get_irq()
+    - NFC: NULL out the dev->rfkill to prevent UAF
+    - efi: Add missing prototype for efi_capsule_setup_info
+    - device property: Check fwnode->secondary when finding properties
+    - device property: Allow error pointer to be passed to fwnode APIs
+    - target: remove an incorrect unmap zeroes data deduction
+    - drbd: fix duplicate array initializer
+    - EDAC/dmc520: Don't print an error for each unconfigured interrupt line
+    - mtd: rawnand: denali: Use managed device resources
+    - HID: hid-led: fix maximum brightness for Dream Cheeky
+    - HID: elan: Fix potential double free in elan_input_configured
+    - drm/bridge: Fix error handling in analogix_dp_probe
+    - regulator: da9121: Fix uninit-value in da9121_assign_chip_model()
+    - drm/mediatek: dpi: Use mt8183 output formats for mt8192
+    - signal: Deliver SIGTRAP on perf event asynchronously if blocked
+    - sched/fair: Fix cfs_rq_clock_pelt() for throttled cfs_rq
+    - sched/psi: report zeroes for CPU full at the system level
+    - spi: img-spfi: Fix pm_runtime_get_sync() error checking
+    - cpufreq: Fix possible race in cpufreq online error path
+    - printk: use atomic updates for klogd work
+    - printk: add missing memory barrier to wake_up_klogd()
+    - printk: wake waiters for safe and NMI contexts
+    - ath9k_htc: fix potential out of bounds access with invalid
+      rxstatus->rs_keyix
+    - media: i2c: max9286: Use dev_err_probe() helper
+    - media: i2c: max9286: Use "maxim,gpio-poc" property
+    - media: i2c: max9286: fix kernel oops when removing module
+    - media: hantro: Empty encoder capture buffers by default
+    - drm/panel: simple: Add missing bus flags for Innolux G070Y2-L01
+    - ALSA: pcm: Check for null pointer of pointer substream before dereferencing
+      it
+    - mtdblock: warn if opened on NAND
+    - inotify: show inotify mask flags in proc fdinfo
+    - fsnotify: fix wrong lockdep annotations
+    - spi: rockchip: Stop spi slave dma receiver when cs inactive
+    - spi: rockchip: Preset cs-high and clk polarity in setup progress
+    - spi: rockchip: fix missing error on unsupported SPI_CS_HIGH
+    - of: overlay: do not break notify on NOTIFY_{OK|STOP}
+    - selftests/damon: add damon to selftests root Makefile
+    - drm/msm/dp: Modify prototype of encoder based API
+    - drm/msm/hdmi: switch to drm_bridge_connector
+    - drm/msm/dpu: adjust display_v_end for eDP and DP
+    - scsi: iscsi: Fix harmless double shift bug
+    - scsi: ufs: qcom: Fix ufs_qcom_resume()
+    - scsi: ufs: core: Exclude UECxx from SFR dump list
+    - drm/v3d: Fix null pointer dereference of pointer perfmon
+    - selftests/resctrl: Fix null pointer dereference on open failed
+    - libbpf: Fix logic for finding matching program for CO-RE relocation
+    - mtd: spi-nor: core: Check written SR value in
+      spi_nor_write_16bit_sr_and_check()
+    - x86/pm: Fix false positive kmemleak report in msr_build_context()
+    - mtd: rawnand: cadence: fix possible null-ptr-deref in
+      cadence_nand_dt_probe()
+    - mtd: rawnand: intel: fix possible null-ptr-deref in ebu_nand_probe()
+    - x86/speculation: Add missing prototype for unpriv_ebpf_notify()
+    - ASoC: rk3328: fix disabling mclk on pclk probe failure
+    - perf tools: Add missing headers needed by util/data.h
+    - drm/msm/disp/dpu1: set vbif hw config to NULL to avoid use after memory free
+      during pm runtime resume
+    - drm/msm/dp: stop event kernel thread when DP unbind
+    - drm/msm/dp: fix error check return value of irq_of_parse_and_map()
+    - drm/msm/dp: reset DP controller before transmit phy test pattern
+    - drm/msm/dp: do not stop transmitting phy test pattern during DP phy
+      compliance test
+    - drm/msm/dsi: fix error checks and return values for DSI xmit functions
+    - drm/msm/hdmi: check return value after calling
+      platform_get_resource_byname()
+    - drm/msm/hdmi: fix error check return value of irq_of_parse_and_map()
+    - drm/msm: add missing include to msm_drv.c
+    - drm/panel: panel-simple: Fix proper bpc for AM-1280800N3TZQW-T00H
+    - kunit: fix debugfs code to use enum kunit_status, not bool
+    - drm/rockchip: vop: fix possible null-ptr-deref in vop_bind()
+    - spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA
+    - [Packaging] add python3-dev as build dependency
+    - perf tools: Use Python devtools for version autodetection rather than
+      runtime
+    - virtio_blk: fix the discard_granularity and discard_alignment queue limits
+    - nl80211: don't hold RTNL in color change request
+    - x86: Fix return value of __setup handlers
+    - irqchip/exiu: Fix acknowledgment of edge triggered interrupts
+    - irqchip/aspeed-i2c-ic: Fix irq_of_parse_and_map() return value
+    - irqchip/aspeed-scu-ic: Fix irq_of_parse_and_map() return value
+    - x86/mm: Cleanup the control_va_addr_alignment() __setup handler
+    - arm64: fix types in copy_highpage()
+    - regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
+    - drm/msm/dsi: fix address for second DSI PHY on SDM660
+    - drm/msm/dp: fix event thread stuck in wait_event after kthread_stop()
+    - drm/msm/mdp5: Return error code in mdp5_pipe_release when deadlock is
+      detected
+    - drm/msm/mdp5: Return error code in mdp5_mixer_release when deadlock is
+      detected
+    - drm/msm: return an error pointer in msm_gem_prime_get_sg_table()
+    - media: uvcvideo: Fix missing check to determine if element is found in list
+    - arm64: stackleak: fix current_top_of_stack()
+    - iomap: iomap_write_failed fix
+    - spi: spi-fsl-qspi: check return value after calling
+      platform_get_resource_byname()
+    - Revert "cpufreq: Fix possible race in cpufreq online error path"
+    - regulator: qcom_smd: Fix up PM8950 regulator configuration
+    - samples: bpf: Don't fail for a missing VMLINUX_BTF when VMLINUX_H is
+      provided
+    - perf/amd/ibs: Use interrupt regs ip for stack unwinding
+    - ath11k: Don't check arvif->is_started before sending management frames
+    - wilc1000: fix crash observed in AP mode with cfg80211_register_netdevice()
+    - HID: amd_sfh: Modify the bus name
+    - HID: amd_sfh: Modify the hid name
+    - ASoC: fsl: Use dev_err_probe() helper
+    - ASoC: fsl: Fix refcount leak in imx_sgtl5000_probe
+    - ASoC: imx-hdmi: Fix refcount leak in imx_hdmi_probe
+    - ASoC: mxs-saif: Fix refcount leak in mxs_saif_probe
+    - regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
+    - dma-direct: factor out a helper for DMA_ATTR_NO_KERNEL_MAPPING allocations
+    - dma-direct: don't fail on highmem CMA pages in dma_direct_alloc_pages
+    - ASoC: samsung: Use dev_err_probe() helper
+    - ASoC: samsung: Fix refcount leak in aries_audio_probe
+    - block: Fix the bio.bi_opf comment
+    - kselftest/cgroup: fix test_stress.sh to use OUTPUT dir
+    - scripts/faddr2line: Fix overlapping text section failures
+    - media: aspeed: Fix an error handling path in aspeed_video_probe()
+    - media: exynos4-is: Fix PM disable depth imbalance in fimc_is_probe
+    - mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
+    - mt76: do not attempt to reorder received 802.3 packets without agg session
+    - media: st-delta: Fix PM disable depth imbalance in delta_probe
+    - media: atmel: atmel-isc: Fix PM disable depth imbalance in atmel_isc_probe
+    - media: i2c: rdacm2x: properly set subdev entity function
+    - media: exynos4-is: Change clk_disable to clk_disable_unprepare
+    - media: pvrusb2: fix array-index-out-of-bounds in pvr2_i2c_core_init
+    - media: vsp1: Fix offset calculation for plane cropping
+    - media: atmel: atmel-sama5d2-isc: fix wrong mask in YUYV format check
+    - media: hantro: HEVC: Fix tile info buffer value computation
+    - Bluetooth: fix dangling sco_conn and use-after-free in sco_sock_timeout
+    - Bluetooth: use hdev lock in activate_scan for hci_is_adv_monitoring
+    - Bluetooth: use hdev lock for accept_list and reject_list in conn req
+    - nvme: set dma alignment to dword
+    - m68k: math-emu: Fix dependencies of math emulation support
+    - sctp: read sk->sk_bound_dev_if once in sctp_rcv()
+    - net: hinic: add missing destroy_workqueue in hinic_pf_to_mgmt_init
+    - ASoC: ti: j721e-evm: Fix refcount leak in j721e_soc_probe_*
+    - kselftest/arm64: bti: force static linking
+    - media: ov7670: remove ov7670_power_off from ov7670_remove
+    - media: i2c: ov5648: fix wrong pointer passed to IS_ERR() and PTR_ERR()
+    - media: staging: media: rkvdec: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - media: rkvdec: h264: Fix dpb_valid implementation
+    - media: rkvdec: h264: Fix bit depth wrap in pps packet
+    - regulator: scmi: Fix refcount leak in scmi_regulator_probe
+    - ext4: reject the 'commit' option on ext2 filesystems
+    - drm/msm/a6xx: Fix refcount leak in a6xx_gpu_init
+    - drm: msm: fix possible memory leak in mdp5_crtc_cursor_set()
+    - x86/sev: Annotate stack change in the #VC handler
+    - drm/msm: don't free the IRQ if it was not requested
+    - selftests/bpf: Add missed ima_setup.sh in Makefile
+    - drm/msm/dpu: handle pm_runtime_get_sync() errors in bind path
+    - drm/i915: Fix CFI violation with show_dynamic_id()
+    - thermal/drivers/bcm2711: Don't clamp temperature at zero
+    - thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe
+    - thermal/core: Fix memory leak in __thermal_cooling_device_register()
+    - thermal/drivers/imx_sc_thermal: Fix refcount leak in imx_sc_thermal_probe
+    - bfq: Relax waker detection for shared queues
+    - bfq: Allow current waker to defend against a tentative one
+    - ASoC: wm2000: fix missing clk_disable_unprepare() on error in
+      wm2000_anc_transition()
+    - PM: domains: Fix initialization of genpd's next_wakeup
+    - net: macb: Fix PTP one step sync support
+    - NFC: hci: fix sleep in atomic context bugs in nfc_hci_hcp_message_tx
+    - ASoC: max98090: Move check for invalid values before casting in
+      max98090_put_enab_tlv()
+    - net: stmmac: selftests: Use kcalloc() instead of kzalloc()
+    - net: stmmac: fix out-of-bounds access in a selftest
+    - hv_netvsc: Fix potential dereference of NULL pointer
+    - hwmon: (pmbus) Check PEC support before reading other registers
+    - rxrpc: Fix listen() setting the bar too high for the prealloc rings
+    - rxrpc: Don't try to resend the request if we're receiving the reply
+    - rxrpc: Fix overlapping ACK accounting
+    - rxrpc: Don't let ack.previousPacket regress
+    - rxrpc: Fix decision on when to generate an IDLE ACK
+    - net: huawei: hinic: Use devm_kcalloc() instead of devm_kzalloc()
+    - hinic: Avoid some over memory allocation
+    - net: dsa: restrict SMSC_LAN9303_I2C kconfig
+    - net/smc: postpone sk_refcnt increment in connect()
+    - dma-direct: factor out dma_set_{de,en}crypted helpers
+    - dma-direct: don't call dma_set_decrypted for remapped allocations
+    - dma-direct: always leak memory that can't be re-encrypted
+    - dma-direct: don't over-decrypt memory
+    - arm64: dts: rockchip: Move drive-impedance-ohm to emmc phy on rk3399
+    - arm64: dts: mt8192: Fix nor_flash status disable typo
+    - memory: samsung: exynos5422-dmc: Avoid some over memory allocation
+    - ARM: dts: BCM5301X: update CRU block description
+    - ARM: dts: BCM5301X: Update pin controller node name
+    - ARM: dts: suniv: F1C100: fix watchdog compatible
+    - soc: qcom: smp2p: Fix missing of_node_put() in smp2p_parse_ipc
+    - soc: qcom: smsm: Fix missing of_node_put() in smsm_parse_ipc
+    - PCI: cadence: Fix find_first_zero_bit() limit
+    - PCI: rockchip: Fix find_first_zero_bit() limit
+    - PCI: mediatek: Fix refcount leak in mtk_pcie_subsys_powerup()
+    - PCI: dwc: Fix setting error return on MSI DMA mapping failure
+    - ARM: dts: ci4x10: Adapt to changes in imx6qdl.dtsi regarding fec clocks
+    - soc: qcom: llcc: Add MODULE_DEVICE_TABLE()
+    - KVM: nVMX: Leave most VM-Exit info fields unmodified on failed VM-Entry
+    - KVM: nVMX: Clear IDT vectoring on nested VM-Exit for double/triple fault
+    - crypto: qat - set CIPHER capability for QAT GEN2
+    - crypto: qat - set COMPRESSION capability for QAT GEN2
+    - crypto: qat - set CIPHER capability for DH895XCC
+    - crypto: qat - set COMPRESSION capability for DH895XCC
+    - platform/chrome: cros_ec: fix error handling in cros_ec_register()
+    - ARM: dts: imx6dl-colibri: Fix I2C pinmuxing
+    - platform/chrome: Re-introduce cros_ec_cmd_xfer and use it for ioctls
+    - can: xilinx_can: mark bit timing constants as const
+    - ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
+    - ARM: dts: bcm2835-rpi-zero-w: Fix GPIO line name for Wifi/BT
+    - ARM: dts: bcm2837-rpi-cm3-io3: Fix GPIO line names for SMPS I2C
+    - ARM: dts: bcm2837-rpi-3-b-plus: Fix GPIO line name of power LED
+    - ARM: dts: bcm2835-rpi-b: Fix GPIO line names
+    - misc: ocxl: fix possible double free in ocxl_file_register_afu
+    - crypto: marvell/cesa - ECB does not IV
+    - gpiolib: of: Introduce hook for missing gpio-ranges
+    - pinctrl: bcm2835: implement hook for missing gpio-ranges
+    - arm: mediatek: select arch timer for mt7629
+    - pinctrl/rockchip: support deferring other gpio params
+    - pinctrl: mediatek: mt8195: enable driver on mtk platforms
+    - arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
+    - Drivers: hv: vmbus: Fix handling of messages with transaction ID of zero
+    - powerpc/fadump: fix PT_LOAD segment for boot memory area
+    - mfd: ipaq-micro: Fix error check return value of platform_get_irq()
+    - scsi: fcoe: Fix Wstringop-overflow warnings in fcoe_wwn_from_mac()
+    - soc: bcm: Check for NULL return of devm_kzalloc()
+    - arm64: dts: ti: k3-am64-mcu: remove incorrect UART base clock rates
+    - ASoC: sh: rz-ssi: Check return value of pm_runtime_resume_and_get()
+    - ASoC: sh: rz-ssi: Propagate error codes returned from
+      platform_get_irq_byname()
+    - ASoC: sh: rz-ssi: Release the DMA channels in rz_ssi_probe() error path
+    - firmware: arm_scmi: Fix list protocols enumeration in the base protocol
+    - nvdimm: Fix firmware activation deadlock scenarios
+    - nvdimm: Allow overwrite in the presence of disabled dimms
+    - pinctrl: mvebu: Fix irq_of_parse_and_map() return value
+    - drivers/base/node.c: fix compaction sysfs file leak
+    - dax: fix cache flush on PMD-mapped pages
+    - drivers/base/memory: fix an unlikely reference counting issue in
+      __add_memory_block()
+    - firmware: arm_ffa: Fix uuid parameter to ffa_partition_probe
+    - firmware: arm_ffa: Remove incorrect assignment of driver_data
+    - list: introduce list_is_head() helper and re-use it in list.h
+    - list: fix a data-race around ep->rdllist
+    - drm/msm/dpu: fix error check return value of irq_of_parse_and_map()
+    - powerpc/8xx: export 'cpm_setbrg' for modules
+    - pinctrl: renesas: r8a779a0: Fix GPIO function on I2C-capable pins
+    - pinctrl: renesas: core: Fix possible null-ptr-deref in
+      sh_pfc_map_resources()
+    - powerpc/idle: Fix return value of __setup() handler
+    - powerpc/4xx/cpm: Fix return value of __setup() handler
+    - RDMA/hns: Add the detection for CMDQ status in the device initialization
+      process
+    - arm64: dts: marvell: espressobin-ultra: fix SPI-NOR config
+    - arm64: dts: marvell: espressobin-ultra: enable front USB3 port
+    - ASoC: atmel-pdmic: Remove endianness flag on pdmic component
+    - ASoC: atmel-classd: Remove endianness flag on class d component
+    - proc: fix dentry/inode overinstantiating under /proc/${pid}/net
+    - ipc/mqueue: use get_tree_nodev() in mqueue_get_tree()
+    - PCI: imx6: Fix PERST# start-up sequence
+    - tty: fix deadlock caused by calling printk() under tty_port->lock
+    - crypto: sun8i-ss - rework handling of IV
+    - crypto: sun8i-ss - handle zero sized sg
+    - crypto: cryptd - Protect per-CPU resource by disabling BH.
+    - ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
+    - hugetlbfs: fix hugetlbfs_statfs() locking
+    - Input: sparcspkr - fix refcount leak in bbc_beep_probe
+    - PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
+    - PCI: microchip: Fix potential race in interrupt handling
+    - hwrng: omap3-rom - fix using wrong clk_disable() in
+      omap_rom_rng_runtime_resume()
+    - powerpc/64: Only WARN if __pa()/__va() called with bad addresses
+    - powerpc/perf: Fix the threshold compare group constraint for power10
+    - powerpc/perf: Fix the threshold compare group constraint for power9
+    - macintosh: via-pmu and via-cuda need RTC_LIB
+    - powerpc/xive: Add some error handling code to 'xive_spapr_init()'
+    - powerpc/xive: Fix refcount leak in xive_spapr_init
+    - powerpc/fsl_rio: Fix refcount leak in fsl_rio_setup
+    - mfd: davinci_voicecodec: Fix possible null-ptr-deref davinci_vc_probe()
+    - nfsd: destroy percpu stats counters after reply cache shutdown
+    - mailbox: forward the hrtimer if not queued and under a lock
+    - RDMA/hfi1: Prevent use of lock before it is initialized
+    - KVM: LAPIC: Drop pending LAPIC timer injection when canceling the timer
+    - Input: stmfts - do not leave device disabled in stmfts_input_open
+    - OPP: call of_node_put() on error path in _bandwidth_supported()
+    - f2fs: support fault injection for dquot_initialize()
+    - f2fs: fix to do sanity check on inline_dots inode
+    - f2fs: fix dereference of stale list iterator after loop body
+    - iommu/amd: Enable swiotlb in all cases
+    - iommu/mediatek: Fix 2 HW sharing pgtable issue
+    - iommu/mediatek: Add list_del in mtk_iommu_remove
+    - iommu/mediatek: Remove clk_disable in mtk_iommu_remove
+    - iommu/mediatek: Add mutex for m4u_group and m4u_dom in data
+    - i2c: at91: use dma safe buffers
+    - cpufreq: mediatek: Use module_init and add module_exit
+    - cpufreq: mediatek: Unregister platform device on exit
+    - iommu/arm-smmu-v3-sva: Fix mm use-after-free
+    - MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
+    - iommu/mediatek: Fix NULL pointer dereference when printing dev_name
+    - i2c: at91: Initialize dma_buf in at91_twi_xfer()
+    - dmaengine: idxd: Fix the error handling path in idxd_cdev_register()
+    - NFS: Do not report EINTR/ERESTARTSYS as mapping errors
+    - NFS: fsync() should report filesystem errors over EINTR/ERESTARTSYS
+    - NFS: Don't report ENOSPC write errors twice
+    - NFS: Do not report flush errors in nfs_write_end()
+    - NFS: Don't report errors from nfs_pageio_complete() more than once
+    - NFSv4/pNFS: Do not fail I/O when we fail to allocate the pNFS layout
+    - NFS: Further fixes to the writeback error handling
+    - video: fbdev: clcdfb: Fix refcount leak in clcdfb_of_vram_setup
+    - dmaengine: stm32-mdma: remove GISR1 register
+    - dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
+    - iommu/amd: Increase timeout waiting for GA log enablement
+    - i2c: npcm: Fix timeout calculation
+    - i2c: npcm: Correct register access width
+    - i2c: npcm: Handle spurious interrupts
+    - i2c: rcar: fix PM ref counts in probe error paths
+    - perf build: Fix btf__load_from_kernel_by_id() feature check
+    - perf c2c: Use stdio interface if slang is not supported
+    - perf jevents: Fix event syntax error caused by ExtSel
+    - video: fbdev: vesafb: Fix a use-after-free due early fb_info cleanup
+    - NFS: Always initialise fattr->label in nfs_fattr_alloc()
+    - NFS: Create a new nfs_alloc_fattr_with_label() function
+    - NFS: Convert GFP_NOFS to GFP_KERNEL
+    - NFSv4.1 mark qualified async operations as MOVEABLE tasks
+    - f2fs: fix to avoid f2fs_bug_on() in dec_valid_node_count()
+    - f2fs: fix to do sanity check on block address in f2fs_do_zero_range()
+    - f2fs: fix to clear dirty inode in f2fs_evict_inode()
+    - f2fs: fix deadloop in foreground GC
+    - f2fs: don't need inode lock for system hidden quota
+    - f2fs: fix to do sanity check on total_data_blocks
+    - f2fs: don't use casefolded comparison for "." and ".."
+    - f2fs: fix fallocate to use file_modified to update permissions consistently
+    - f2fs: fix to do sanity check for inline inode
+    - wifi: mac80211: fix use-after-free in chanctx code
+    - iwlwifi: mvm: fix assert 1F04 upon reconfig
+    - fs-writeback: writeback_sb_inodes：Recalculate 'wrote' according skipped
+      pages
+    - efi: Do not import certificates from UEFI Secure Boot for T2 Macs
+    - bfq: Avoid false marking of bic as stably merged
+    - bfq: Avoid merging queues with different parents
+    - bfq: Split shared queues on move between cgroups
+    - bfq: Update cgroup information before merging bio
+    - bfq: Drop pointless unlock-lock pair
+    - bfq: Remove pointless bfq_init_rq() calls
+    - bfq: Track whether bfq_group is still online
+    - bfq: Get rid of __bio_blkcg() usage
+    - bfq: Make sure bfqg for which we are queueing requests is online
+    - ext4: mark group as trimmed only if it was fully scanned
+    - ext4: fix use-after-free in ext4_rename_dir_prepare
+    - ext4: fix race condition between ext4_write and ext4_convert_inline_data
+    - ext4: fix warning in ext4_handle_inode_extension
+    - ext4: fix bug_on in ext4_writepages
+    - ext4: filter out EXT4_FC_REPLAY from on-disk superblock field s_state
+    - ext4: fix bug_on in __es_tree_search
+    - ext4: verify dir block before splitting it
+    - ext4: avoid cycles in directory h-tree
+    - ACPI: property: Release subnode properties with data nodes
+    - tty: goldfish: Introduce gf_ioread32()/gf_iowrite32()
+    - tracing: Fix potential double free in create_var_ref()
+    - tracing: Initialize integer variable to prevent garbage return value
+    - drm/amdgpu: add beige goby PCI ID
+    - PCI/PM: Fix bridge_d3_blacklist[] Elo i2 overwrite of Gigabyte X299
+    - PCI: qcom: Fix runtime PM imbalance on probe errors
+    - PCI: qcom: Fix unbalanced PHY init on probe errors
+    - staging: r8188eu: prevent ->Ssid overflow in rtw_wx_set_scan()
+    - mm, compaction: fast_find_migrateblock() should return pfn in the target
+      zone
+    - s390/perf: obtain sie_block from the right address
+    - s390/stp: clock_delta should be signed
+    - dlm: fix plock invalid read
+    - dlm: uninitialized variable on error in dlm_listen_for_all()
+    - dlm: fix missing lkb refcount handling
+    - ocfs2: dlmfs: fix error handling of user_dlm_destroy_lock
+    - scsi: dc395x: Fix a missing check on list iterator
+    - scsi: ufs: qcom: Add a readl() to make sure ref_clk gets enabled
+    - landlock: Add clang-format exceptions
+    - landlock: Format with clang-format
+    - selftests/landlock: Add clang-format exceptions
+    - selftests/landlock: Normalize array assignment
+    - selftests/landlock: Format with clang-format
+    - samples/landlock: Add clang-format exceptions
+    - samples/landlock: Format with clang-format
+    - landlock: Fix landlock_add_rule(2) documentation
+    - selftests/landlock: Make tests build with old libc
+    - selftests/landlock: Extend tests for minimal valid attribute size
+    - selftests/landlock: Add tests for unknown access rights
+    - selftests/landlock: Extend access right tests to directories
+    - selftests/landlock: Fully test file rename with "remove" access
+    - selftests/landlock: Add tests for O_PATH
+    - landlock: Change landlock_add_rule(2) argument check ordering
+    - landlock: Change landlock_restrict_self(2) check ordering
+    - selftests/landlock: Test landlock_create_ruleset(2) argument check ordering
+    - landlock: Define access_mask_t to enforce a consistent access mask size
+    - landlock: Reduce the maximum number of layers to 16
+    - landlock: Create find_rule() from unmask_layers()
+    - landlock: Fix same-layer rule unions
+    - drm/amdgpu/cs: make commands with 0 chunks illegal behaviour.
+    - drm/nouveau/subdev/bus: Ratelimit logging for fault errors
+    - drm/etnaviv: check for reaped mapping in etnaviv_iommu_unmap_gem
+    - drm/nouveau/clk: Fix an incorrect NULL check on list iterator
+    - drm/nouveau/kms/nv50-: atom: fix an incorrect NULL check on list iterator
+    - drm/bridge: analogix_dp: Grab runtime PM reference for DP-AUX
+    - drm/i915/dsi: fix VBT send packet port selection for ICL+
+    - md: fix an incorrect NULL check in does_sb_need_changing
+    - md: fix an incorrect NULL check in md_reload_sb
+    - mtd: cfi_cmdset_0002: Move and rename
+      chip_check/chip_ready/chip_good_for_write
+    - mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
+    - media: coda: Fix reported H264 profile
+    - media: coda: Add more H264 levels for CODA960
+    - ima: remove the IMA_TEMPLATE Kconfig option
+    - [Config] updateconfigs for IMA_TEMPLATE
+    - Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug
+    - RDMA/hfi1: Fix potential integer multiplication overflow errors
+    - mmc: core: Allows to override the timeout value for ioctl() path
+    - csky: patch_text: Fixup last cpu should be master
+    - irqchip/armada-370-xp: Do not touch Performance Counter Overflow on A375,
+      A38x, A39x
+    - irqchip: irq-xtensa-mx: fix initial IRQ affinity
+    - thermal: devfreq_cooling: use local ops instead of global ops
+    - cfg80211: declare MODULE_FIRMWARE for regulatory.db
+    - mac80211: upgrade passive scan to active scan on DFS channels after beacon
+      rx
+    - um: Use asm-generic/dma-mapping.h
+    - um: chan_user: Fix winch_tramp() return value
+    - um: Fix out-of-bounds read in LDT setup
+    - kexec_file: drop weak attribute from arch_kexec_apply_relocations[_add]
+    - ftrace: Clean up hash direct_functions on register failures
+    - ksmbd: fix outstanding credits related bugs
+    - iommu/msm: Fix an incorrect NULL check on list iterator
+    - iommu/dma: Fix iova map result check bug
+    - Revert "mm/cma.c: remove redundant cma_mutex lock"
+    - mm/page_alloc: always attempt to allocate at least one page during bulk
+      allocation
+    - nodemask.h: fix compilation error with GCC12
+    - hugetlb: fix huge_pmd_unshare address update
+    - mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
+    - xtensa/simdisk: fix proc_read_simdisk()
+    - rtl818x: Prevent using not initialized queues
+    - ASoC: rt5514: Fix event generation for "DSP Voice Wake Up" control
+    - carl9170: tx: fix an incorrect use of list iterator
+    - stm: ltdc: fix two incorrect NULL checks on list iterator
+    - bcache: remove incremental dirty sector counting for
+      bch_sectors_dirty_init()
+    - bcache: avoid journal no-space deadlock by reserving 1 journal bucket
+    - serial: pch: don't overwrite xmit->buf[0] by x_char
+    - tilcdc: tilcdc_external: fix an incorrect NULL check on list iterator
+    - gma500: fix an incorrect NULL check on list iterator
+    - arm64: dts: qcom: ipq8074: fix the sleep clock frequency
+    - arm64: tegra: Add missing DFLL reset on Tegra210
+    - clk: tegra: Add missing reset deassertion
+    - phy: qcom-qmp: fix struct clk leak on probe errors
+    - ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
+    - ARM: pxa: maybe fix gpio lookup tables
+    - SMB3: EBADF/EIO errors in rename/open caused by race condition in
+      smb2_compound_op
+    - docs/conf.py: Cope with removal of language=None in Sphinx 5.0.0
+    - dt-bindings: gpio: altera: correct interrupt-cells
+    - vdpasim: allow to enable a vq repeatedly
+    - blk-iolatency: Fix inflight count imbalances and IO hangs on offline
+    - coresight: core: Fix coresight device probe failure issue
+    - phy: qcom-qmp: fix reset-controller leak on probe errors
+    - net: ipa: fix page free in ipa_endpoint_trans_release()
+    - net: ipa: fix page free in ipa_endpoint_replenish_one()
+    - kseltest/cgroup: Make test_stress.sh work if run interactively
+    - list: test: Add a test for list_is_head()
+    - staging: r8188eu: delete rtw_wx_read/write32()
+    - RDMA/hns: Remove the num_cqc_timer variable
+    - RDMA/rxe: Generate a completion for unsupported/invalid opcode
+    - MIPS: IP27: Remove incorrect `cpu_has_fpu' override
+    - MIPS: IP30: Remove incorrect `cpu_has_fpu' override
+    - ext4: only allow test_dummy_encryption when supported
+    - interconnect: qcom: sc7180: Drop IP0 interconnects
+    - interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate
+    - fs: add two trivial lookup helpers
+    - exportfs: support idmapped mounts
+    - fs/ntfs3: Fix invalid free in log_replay
+    - md: Don't set mddev private to NULL in raid0 pers->free
+    - md: fix double free of io_acct_set bioset
+    - md: bcache: check the return value of kzalloc() in detached_dev_do_request()
+    - pinctrl/rockchip: support setting input-enable param
+    - block: fix bio_clone_blkg_association() to associate with proper blkcg_gq
+    - Linux 5.15.46
+  * [SRU] bcache deadlock during read IO in writeback mode (LP: #1980925) //
+    Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - bcache: improve multithreaded bch_btree_check()
+    - bcache: improve multithreaded bch_sectors_dirty_init()
+  * Jammy update: v5.15.45 upstream stable release (LP: #1981862)
+    - ALSA: usb-audio: Don't get sample rate for MCT Trigger 5 USB-to-HDMI
+    - pinctrl: sunxi: fix f1c100s uart2 function
+    - KVM: arm64: Don't hypercall before EL2 init
+    - percpu_ref_init(): clean ->percpu_count_ref on failure
+    - net: af_key: check encryption module availability consistency
+    - nfc: pn533: Fix buggy cleanup order
+    - net: ftgmac100: Disable hardware checksum on AST2600
+    - i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging
+    - drivers: i2c: thunderx: Allow driver to work with ACPI defined TWSI
+      controllers
+    - i2c: ismt: prevent memory corruption in ismt_access()
+    - assoc_array: Fix BUG_ON during garbage collect
+    - pipe: make poll_usage boolean and annotate its access
+    - pipe: Fix missing lock in pipe_resize_ring()
+    - net: ipa: compute proper aggregation limit
+    - drm/i915: Fix -Wstringop-overflow warning in call to intel_read_wm_latency()
+    - exfat: check if cluster num is valid
+    - lib/crypto: add prompts back to crypto libraries
+    - crypto: drbg - prepare for more fine-grained tracking of seeding state
+    - crypto: drbg - track whether DRBG was seeded with !rng_is_initialized()
+    - crypto: drbg - move dynamic ->reseed_threshold adjustments to __drbg_seed()
+    - crypto: drbg - make reseeding from get_random_bytes() synchronous
+    - netfilter: nf_tables: hold mutex on netns pre_exit path
+    - netfilter: nf_tables: double hook unregistration in netns path
+    - netfilter: conntrack: re-fetch conntrack after insertion
+    - KVM: PPC: Book3S HV: fix incorrect NULL check on list iterator
+    - x86/kvm: Alloc dummy async #PF token outside of raw spinlock
+    - x86, kvm: use correct GFP flags for preemption disabled
+    - KVM: x86: avoid calling x86 emulator without a decoded instruction
+    - KVM: x86: Drop WARNs that assert a triple fault never "escapes" from L2
+    - KVM: SVM: Use kzalloc for sev ioctl interfaces to prevent kernel data leak
+    - crypto: caam - fix i.MX6SX entropy delay value
+    - crypto: ecrdsa - Fix incorrect use of vli_cmp
+    - zsmalloc: fix races between asynchronous zspage free and page migration
+    - ALSA: usb-audio: Workaround for clock setup on TEAC devices
+    - ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
+    - ALSA: usb-audio: Configure sync endpoints before data
+    - Bluetooth: hci_qca: Use del_timer_sync() before freeing
+    - ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
+    - dm integrity: fix error code in dm_integrity_ctr()
+    - dm crypt: make printing of the key constant-time
+    - dm stats: add cond_resched when looping over entries
+    - dm verity: set DM_TARGET_IMMUTABLE feature flag
+    - raid5: introduce MD_BROKEN
+    - fs/ntfs3: validate BOOT sectors_per_clusters
+    - HID: multitouch: Add support for Google Whiskers Touchpad
+    - HID: multitouch: add quirks to enable Lenovo X12 trackpoint
+    - x86/sgx: Disconnect backing page references from dirty status
+    - x86/sgx: Mark PCMD page as dirty when modifying contents
+    - x86/sgx: Obtain backing storage page with enclave mutex held
+    - x86/sgx: Fix race between reclaimer and page fault handler
+    - x86/sgx: Ensure no data in PCMD page after truncate
+    - media: i2c: imx412: Fix reset GPIO polarity
+    - media: i2c: imx412: Fix power_off ordering
+    - tpm: Fix buffer access in tpm2_get_tpm_pt()
+    - tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()
+    - docs: submitting-patches: Fix crossref to 'The canonical patch format'
+    - NFS: Memory allocation failures are not server fatal errors
+    - NFSD: Fix possible sleep during nfsd4_release_lockowner()
+    - bpf: Fix potential array overflow in bpf_trampoline_get_progs()
+    - bpf: Enlarge offset check value to INT_MAX in bpf_skb_{load,store}_bytes
+    - bpf: Fix excessive memory allocation in stack_map_alloc()
+    - bpf: Reject writes for PTR_TO_MAP_KEY in check_helper_mem_access
+    - bpf: Check PTR_TO_MEM | MEM_RDONLY in check_helper_mem_access
+    - ALSA: usb-audio: Optimize TEAC clock quirk
+    - Linux 5.15.45
+  * Jammy update: v5.15.44 upstream stable release (LP: #1981649)
+    - Revert "UBUNTU: SAUCE: random: Make getrandom() ready earlier"
+    - ice: fix crash at allocation failure
+    - ACPI: sysfs: Fix BERT error region memory mapping
+    - MAINTAINERS: co-maintain random.c
+    - MAINTAINERS: add git tree for random.c
+    - lib/crypto: blake2s: include as built-in
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - lib/crypto: blake2s: move hmac construction into wireguard
+    - lib/crypto: sha1: re-roll loops to reduce code size
+    - lib/crypto: blake2s: avoid indirect calls to compression function for Clang
+      CFI
+    - random: document add_hwgenerator_randomness() with other input functions
+    - random: remove unused irq_flags argument from add_interrupt_randomness()
+    - random: use BLAKE2s instead of SHA1 in extraction
+    - random: do not sign extend bytes for rotation when mixing
+    - random: do not re-init if crng_reseed completes before primary init
+    - random: mix bootloader randomness into pool
+    - random: harmonize "crng init done" messages
+    - random: use IS_ENABLED(CONFIG_NUMA) instead of ifdefs
+    - random: early initialization of ChaCha constants
+    - random: avoid superfluous call to RDRAND in CRNG extraction
+    - random: don't reset crng_init_cnt on urandom_read()
+    - random: fix typo in comments
+    - random: cleanup poolinfo abstraction
+    - random: cleanup integer types
+    - random: remove incomplete last_data logic
+    - random: remove unused extract_entropy() reserved argument
+    - random: rather than entropy_store abstraction, use global
+    - random: remove unused OUTPUT_POOL constants
+    - random: de-duplicate INPUT_POOL constants
+    - random: prepend remaining pool constants with POOL_
+    - random: cleanup fractional entropy shift constants
+    - random: access input_pool_data directly rather than through pointer
+    - random: selectively clang-format where it makes sense
+    - random: simplify arithmetic function flow in account()
+    - random: continually use hwgenerator randomness
+    - random: access primary_pool directly rather than through pointer
+    - random: only call crng_finalize_init() for primary_crng
+    - random: use computational hash for entropy extraction
+    - random: simplify entropy debiting
+    - random: use linear min-entropy accumulation crediting
+    - random: always wake up entropy writers after extraction
+    - random: make credit_entropy_bits() always safe
+    - random: remove use_input_pool parameter from crng_reseed()
+    - random: remove batched entropy locking
+    - random: fix locking in crng_fast_load()
+    - random: use RDSEED instead of RDRAND in entropy extraction
+    - random: get rid of secondary crngs
+    - random: inline leaves of rand_initialize()
+    - random: ensure early RDSEED goes through mixer on init
+    - random: do not xor RDRAND when writing into /dev/random
+    - random: absorb fast pool into input pool after fast load
+    - random: use simpler fast key erasure flow on per-cpu keys
+    - random: use hash function for crng_slow_load()
+    - random: make more consistent use of integer types
+    - random: remove outdated INT_MAX >> 6 check in urandom_read()
+    - random: zero buffer after reading entropy from userspace
+    - random: fix locking for crng_init in crng_reseed()
+    - random: tie batched entropy generation to base_crng generation
+    - random: remove ifdef'd out interrupt bench
+    - random: remove unused tracepoints
+    - random: add proper SPDX header
+    - random: deobfuscate irq u32/u64 contributions
+    - random: introduce drain_entropy() helper to declutter crng_reseed()
+    - random: remove useless header comment
+    - random: remove whitespace and reorder includes
+    - random: group initialization wait functions
+    - random: group crng functions
+    - random: group entropy extraction functions
+    - random: group entropy collection functions
+    - random: group userspace read/write functions
+    - random: group sysctl functions
+    - random: rewrite header introductory comment
+    - random: defer fast pool mixing to worker
+    - random: do not take pool spinlock at boot
+    - random: unify early init crng load accounting
+    - random: check for crng_init == 0 in add_device_randomness()
+    - random: pull add_hwgenerator_randomness() declaration into random.h
+    - random: clear fast pool, crng, and batches in cpuhp bring up
+    - random: round-robin registers as ulong, not u32
+    - random: only wake up writers after zap if threshold was passed
+    - random: cleanup UUID handling
+    - random: unify cycles_t and jiffies usage and types
+    - random: do crng pre-init loading in worker rather than irq
+    - random: give sysctl_random_min_urandom_seed a more sensible value
+    - random: don't let 644 read-only sysctls be written to
+    - random: replace custom notifier chain with standard one
+    - random: use SipHash as interrupt entropy accumulator
+    - random: make consistent usage of crng_ready()
+    - random: reseed more often immediately after booting
+    - random: check for signal and try earlier when generating entropy
+    - random: skip fast_init if hwrng provides large chunk of entropy
+    - random: treat bootloader trust toggle the same way as cpu trust toggle
+    - random: re-add removed comment about get_random_{u32,u64} reseeding
+    - random: mix build-time latent entropy into pool at init
+    - random: do not split fast init input in add_hwgenerator_randomness()
+    - random: do not allow user to keep crng key around on stack
+    - random: check for signal_pending() outside of need_resched() check
+    - random: check for signals every PAGE_SIZE chunk of /dev/[u]random
+    - random: allow partial reads if later user copies fail
+    - random: make random_get_entropy() return an unsigned long
+    - random: document crng_fast_key_erasure() destination possibility
+    - random: fix sysctl documentation nits
+    - init: call time_init() before rand_initialize()
+    - ia64: define get_cycles macro for arch-override
+    - s390: define get_cycles macro for arch-override
+    - parisc: define get_cycles macro for arch-override
+    - alpha: define get_cycles macro for arch-override
+    - powerpc: define get_cycles macro for arch-override
+    - timekeeping: Add raw clock fallback for random_get_entropy()
+    - m68k: use fallback for random_get_entropy() instead of zero
+    - riscv: use fallback for random_get_entropy() instead of zero
+    - mips: use fallback for random_get_entropy() instead of just c0 random
+    - arm: use fallback for random_get_entropy() instead of zero
+    - nios2: use fallback for random_get_entropy() instead of zero
+    - x86/tsc: Use fallback for random_get_entropy() instead of zero
+    - um: use fallback for random_get_entropy() instead of zero
+    - sparc: use fallback for random_get_entropy() instead of zero
+    - xtensa: use fallback for random_get_entropy() instead of zero
+    - random: insist on random_get_entropy() existing in order to simplify
+    - random: do not use batches when !crng_ready()
+    - random: use first 128 bits of input as fast init
+    - random: do not pretend to handle premature next security model
+    - random: order timer entropy functions below interrupt functions
+    - random: do not use input pool from hard IRQs
+    - random: help compiler out with fast_mix() by using simpler arguments
+    - siphash: use one source of truth for siphash permutations
+    - random: use symbolic constants for crng_init states
+    - random: avoid initializing twice in credit race
+    - random: move initialization out of reseeding hot path
+    - random: remove ratelimiting for in-kernel unseeded randomness
+    - random: use proper jiffies comparison macro
+    - random: handle latent entropy and command line from random_init()
+    - random: credit architectural init the exact amount
+    - random: use static branch for crng_ready()
+    - random: remove extern from functions in header
+    - random: use proper return types on get_random_{int,long}_wait()
+    - random: make consistent use of buf and len
+    - random: move initialization functions out of hot pages
+    - random: move randomize_page() into mm where it belongs
+    - random: unify batched entropy implementations
+    - random: convert to using fops->read_iter()
+    - random: convert to using fops->write_iter()
+    - random: wire up fops->splice_{read,write}_iter()
+    - random: check for signals after page of pool writes
+    - ALSA: ctxfi: Add SB046x PCI ID
+    - Linux 5.15.44
+    - Revert "random: use static branch for crng_ready()"
+  * Jammy update: v5.15.43 upstream stable release (LP: #1981468)
+    - mptcp: Do TCP fallback on early DSS checksum failure
+    - Linux 5.15.43
+  * Jammy update: v5.15.42 upstream stable release (LP: #1981375)
+    - usb: gadget: fix race when gadget driver register via ioctl
+    - io_uring: arm poll for non-nowait files
+    - kernel/resource: Introduce request_mem_region_muxed()
+    - i2c: piix4: Replace hardcoded memory map size with a #define
+    - i2c: piix4: Move port I/O region request/release code into functions
+    - i2c: piix4: Move SMBus controller base address detect into function
+    - i2c: piix4: Move SMBus port selection into function
+    - i2c: piix4: Add EFCH MMIO support to region request and release
+    - i2c: piix4: Add EFCH MMIO support to SMBus base address detect
+    - i2c: piix4: Add EFCH MMIO support for SMBus port select
+    - i2c: piix4: Enable EFCH MMIO for Family 17h+
+    - Watchdog: sp5100_tco: Move timer initialization into function
+    - Watchdog: sp5100_tco: Refactor MMIO base address initialization
+    - Watchdog: sp5100_tco: Add initialization using EFCH MMIO
+    - Watchdog: sp5100_tco: Enable Family 17h+ CPUs
+    - mm/kfence: reset PG_slab and memcg_data before freeing __kfence_pool
+    - Revert "drm/i915/opregion: check port number bounds for SWSCI display power
+      state"
+    - rtc: fix use-after-free on device removal
+    - rtc: pcf2127: fix bug when reading alarm registers
+    - um: Cleanup syscall_handler_t definition/cast, fix warning
+    - Input: add bounds checking to input_set_capability()
+    - Input: stmfts - fix reference leak in stmfts_input_open
+    - nvme-pci: add quirks for Samsung X5 SSDs
+    - gfs2: Disable page faults during lockless buffered reads
+    - rtc: sun6i: Fix time overflow handling
+    - crypto: stm32 - fix reference leak in stm32_crc_remove
+    - crypto: x86/chacha20 - Avoid spurious jumps to other functions
+    - s390/traps: improve panic message for translation-specification exception
+    - s390/pci: improve zpci_dev reference counting
+    - vhost_vdpa: don't setup irq offloading when irq_num < 0
+    - tools/virtio: compile with -pthread
+    - nvmet: use a private workqueue instead of the system workqueue
+    - nvme-multipath: fix hang when disk goes live over reconnect
+    - rtc: mc146818-lib: Fix the AltCentury for AMD platforms
+    - fs: fix an infinite loop in iomap_fiemap
+    - MIPS: lantiq: check the return value of kzalloc()
+    - drbd: remove usage of list iterator variable after loop
+    - platform/chrome: cros_ec_debugfs: detach log reader wq from devm
+    - ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
+    - nilfs2: fix lockdep warnings in page operations for btree nodes
+    - nilfs2: fix lockdep warnings during disk space reclamation
+    - ALSA: usb-audio: Restore Rane SL-1 quirk
+    - ALSA: wavefront: Proper check of get_user() error
+    - ALSA: hda/realtek: Add quirk for TongFang devices with pop noise
+    - perf: Fix sys_perf_event_open() race against self
+    - selinux: fix bad cleanup on error in hashtab_duplicate()
+    - Fix double fget() in vhost_net_set_backend()
+    - PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
+    - Revert "can: m_can: pci: use custom bit timings for Elkhart Lake"
+    - KVM: x86/mmu: Update number of zapped pages even if page list is stable
+    - arm64: paravirt: Use RCU read locks to guard stolen_time
+    - arm64: mte: Ensure the cleared tags are visible before setting the PTE
+    - crypto: qcom-rng - fix infinite loop on requests not multiple of WORD_SZ
+    - libceph: fix potential use-after-free on linger ping and resends
+    - drm/i915/dmc: Add MMIO range restrictions
+    - drm/dp/mst: fix a possible memory leak in fetch_monitor_name()
+    - dma-buf: fix use of DMA_BUF_SET_NAME_{A,B} in userspace
+    - dma-buf: ensure unique directory name for dmabuf stats
+    - ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi
+    - pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl
+    - ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group
+    - ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
+    - ARM: dts: aspeed: Add secure boot controller node
+    - ARM: dts: aspeed: Add video engine to g6
+    - pinctrl: mediatek: mt8365: fix IES control pins
+    - ALSA: hda - fix unused Realtek function when PM is not enabled
+    - net: ipa: record proper RX transaction count
+    - net: macb: Increment rx bd head after allocating skb and buffer
+    - xfrm: rework default policy structure
+    - xfrm: fix "disable_policy" flag use when arriving from different devices
+    - net/sched: act_pedit: sanitize shift argument before usage
+    - netfilter: flowtable: fix excessive hw offload attempts after failure
+    - netfilter: nft_flow_offload: skip dst neigh lookup for ppp devices
+    - net: fix dev_fill_forward_path with pppoe + bridge
+    - netfilter: nft_flow_offload: fix offload with pppoe + vlan
+    - net: systemport: Fix an error handling path in bcm_sysport_probe()
+    - net: vmxnet3: fix possible use-after-free bugs in vmxnet3_rq_alloc_rx_buf()
+    - net: vmxnet3: fix possible NULL pointer dereference in vmxnet3_rq_cleanup()
+    - ice: fix crash when writing timestamp on RX rings
+    - ice: fix possible under reporting of ethtool Tx and Rx statistics
+    - ice: move ice_container_type onto ice_ring_container
+    - ice: Fix interrupt moderation settings getting cleared
+    - clk: at91: generated: consider range when calculating best rate
+    - net/qla3xxx: Fix a test in ql_reset_work()
+    - NFC: nci: fix sleep in atomic context bugs caused by nci_skb_alloc
+    - net/mlx5: DR, Fix missing flow_source when creating multi-destination FW
+      table
+    - net/mlx5e: Properly block LRO when XDP is enabled
+    - ARM: 9196/1: spectre-bhb: enable for Cortex-A15
+    - ARM: 9197/1: spectre-bhb: fix loop8 sequence for Thumb2
+    - mptcp: change the parameter of __mptcp_make_csum
+    - mptcp: reuse __mptcp_make_csum in validate_data_csum
+    - mptcp: fix checksum byte order
+    - igb: skip phy status check where unavailable
+    - netfilter: flowtable: fix TCP flow teardown
+    - netfilter: flowtable: pass flowtable to nf_flow_table_iterate()
+    - netfilter: flowtable: move dst_check to packet path
+    - net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
+    - riscv: dts: sifive: fu540-c000: align dma node name with dtschema
+    - scsi: ufs: core: Fix referencing invalid rsp field
+    - perf build: Fix check for btf__load_from_kernel_by_id() in libbpf
+    - gpio: gpio-vf610: do not touch other bits when set the target bit
+    - gpio: mvebu/pwm: Refuse requests with inverted polarity
+    - perf regs x86: Fix arch__intr_reg_mask() for the hybrid platform
+    - perf bench numa: Address compiler error on s390
+    - scsi: scsi_dh_alua: Properly handle the ALUA transitioning state
+    - scsi: qla2xxx: Fix missed DMA unmap for aborted commands
+    - mac80211: fix rx reordering with non explicit / psmp ack policy
+    - nl80211: validate S1G channel width
+    - selftests: add ping test with ping_group_range tuned
+    - fbdev: Prevent possible use-after-free in fb_release()
+    - net: fix wrong network header length
+    - nl80211: fix locking in nl80211_set_tx_bitrate_mask()
+    - ethernet: tulip: fix missing pci_disable_device() on error in
+      tulip_init_one()
+    - net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()
+    - net: atlantic: fix "frag[0] not initialized"
+    - net: atlantic: reduce scope of is_rsc_complete
+    - net: atlantic: add check for MAX_SKB_FRAGS
+    - net: atlantic: verify hw_head_ lies within TX buffer ring
+    - arm64: Enable repeat tlbi workaround on KRYO4XX gold CPUs
+    - Input: ili210x - fix reset timing
+    - dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group
+    - i2c: mt7621: fix missing clk_disable_unprepare() on error in mtk_i2c_probe()
+    - afs: Fix afs_getattr() to refetch file status if callback break occurred
+    - Linux 5.15.42
+  * CVE-2021-33061
+    - ixgbe: add the ability for the PF to disable VF link state
+    - ixgbe: add improvement for MDD response functionality
+    - ixgbevf: add disable link state
+  * Fix PSR flickers on Intel TGL laptops + AUO panel (LP: #1980087)
+    - SAUCE: drm/i915/display/psr: Fix flicker on TGL + AUO panel
+  * Fix audio on Zbook Studio G9  (LP: #1966010)
+    - ALSA: hda/realtek: Fix LED on Zbook Studio G9
+  * Support Cirrus audio codec configurations for Odin platform (LP: #1968861)
+    - ALSA: hda/cs8409: Support new Odin Variants
+    - ALSA: hda/cs8409: Add Speaker Playback Switch for Cyborg
+  * Fix beacon loss for rtl8821ce on certain platforms (LP: #1969771)
+    - rtw88: pci: 8821c: Disable 21ce completion timeout
+  * Suppress harmless warning from hp-wmi (LP: #1980307)
+    - platform/x86: hp-wmi: Ignore Sanitization Mode event
+  * Fix headset mic no sound on an HP desktop (LP: #1978925)
+    - ALSA: hda/realtek - ALC897 headset MIC no sound
+  * alsa/hda: mute led can't work on the lenovo machine with cs35l41 s-codec
+    (LP: #1978915)
+    - ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec
+  * Jammy update: v5.15.41 upstream stable release (LP: #1980278)
+    - batman-adv: Don't skb_split skbuffs with frag_list
+    - iwlwifi: iwl-dbg: Use del_timer_sync() before freeing
+    - hwmon: (tmp401) Add OF device ID table
+    - mac80211: Reset MBSSID parameters upon connection
+    - net: Fix features skip in for_each_netdev_feature()
+    - net: mscc: ocelot: fix last VCAP IS1/IS2 filter persisting in hardware when
+      deleted
+    - net: mscc: ocelot: fix VCAP IS2 filters matching on both lookups
+    - net: mscc: ocelot: restrict tc-trap actions to VCAP IS2 lookup 0
+    - net: mscc: ocelot: avoid corrupting hardware counters when moving VCAP
+      filters
+    - fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
+    - fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
+    - fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
+    - platform/surface: aggregator: Fix initialization order when compiling as
+      builtin module
+    - ice: Fix race during aux device (un)plugging
+    - ice: fix PTP stale Tx timestamps cleanup
+    - ipv4: drop dst in multicast routing path
+    - drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
+    - netlink: do not reset transport header in netlink_recvmsg()
+    - net: chelsio: cxgb4: Avoid potential negative array offset
+    - fbdev: efifb: Fix a use-after-free due early fb_info cleanup
+    - sfc: Use swap() instead of open coding it
+    - net: sfc: fix memory leak due to ptp channel
+    - mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protection
+    - nfs: fix broken handling of the softreval mount option
+    - ionic: fix missing pci_release_regions() on error in ionic_probe()
+    - dim: initialize all struct fields
+    - hwmon: (ltq-cputemp) restrict it to SOC_XWAY
+    - procfs: prevent unprivileged processes accessing fdinfo dir
+    - selftests: vm: Makefile: rename TARGETS to VMTARGETS
+    - arm64: vdso: fix makefile dependency on vdso.so
+    - virtio: fix virtio transitional ids
+    - s390/ctcm: fix variable dereferenced before check
+    - s390/ctcm: fix potential memory leak
+    - s390/lcs: fix variable dereferenced before check
+    - net/sched: act_pedit: really ensure the skb is writable
+    - net: ethernet: mediatek: ppe: fix wrong size passed to memset()
+    - net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral
+    - drm/vc4: hdmi: Fix build error for implicit function declaration
+    - net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
+    - net/smc: non blocking recvmsg() return -EAGAIN when no data and
+      signal_pending
+    - net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
+    - tls: Fix context leak on tls_device_down
+    - drm/vmwgfx: Fix fencing on SVGAv3
+    - gfs2: Fix filesystem block deallocation for short writes
+    - hwmon: (f71882fg) Fix negative temperature
+    - RDMA/irdma: Fix deadlock in irdma_cleanup_cm_core()
+    - iommu: arm-smmu: disable large page mappings for Nvidia arm-smmu
+    - ASoC: max98090: Reject invalid values in custom control put()
+    - ASoC: max98090: Generate notifications on changes for custom control
+    - ASoC: ops: Validate input values in snd_soc_put_volsw_range()
+    - s390: disable -Warray-bounds
+    - ASoC: SOF: Fix NULL pointer exception in sof_pci_probe callback
+    - net: emaclite: Don't advertise 1000BASE-T and do auto negotiation
+    - net: sfp: Add tx-fault workaround for Huawei MA5671A SFP ONT
+    - secure_seq: use the 64 bits of the siphash for port offset calculation
+    - tcp: use different parts of the port_offset for index and offset
+    - tcp: resalt the secret every 10 seconds
+    - tcp: add small random increments to the source port
+    - tcp: dynamically allocate the perturb table used by source ports
+    - tcp: increase source port perturb table to 2^16
+    - tcp: drop the hash_32() part from the index calculation
+    - interconnect: Restore sync state by ignoring ipa-virt in provider count
+    - firmware_loader: use kernel credentials when reading firmware
+    - KVM: PPC: Book3S PR: Enable MSR_DR for switch_mmu_context()
+    - usb: xhci-mtk: fix fs isoc's transfer error
+    - x86/mm: Fix marking of unused sub-pmd ranges
+    - tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
+    - tty: n_gsm: fix buffer over-read in gsm_dlci_data()
+    - tty: n_gsm: fix mux activation issues in gsm_config()
+    - usb: cdc-wdm: fix reading stuck on device close
+    - usb: typec: tcpci: Don't skip cleanup in .remove() on error
+    - usb: typec: tcpci_mt6360: Update for BMC PHY setting
+    - USB: serial: pl2303: add device id for HP LM930 Display
+    - USB: serial: qcserial: add support for Sierra Wireless EM7590
+    - USB: serial: option: add Fibocom L610 modem
+    - USB: serial: option: add Fibocom MA510 modem
+    - slimbus: qcom: Fix IRQ check in qcom_slim_probe
+    - fsl_lpuart: Don't enable interrupts too early
+    - serial: 8250_mtk: Fix UART_EFR register address
+    - serial: 8250_mtk: Fix register address for XON/XOFF character
+    - ceph: fix setting of xattrs on async created inodes
+    - Revert "mm/memory-failure.c: skip huge_zero_page in memory_failure()"
+    - mm/huge_memory: do not overkill when splitting huge_zero_page
+    - drm/vmwgfx: Disable command buffers on svga3 without gbobjects
+    - drm/nouveau/tegra: Stop using iommu_present()
+    - i40e: i40e_main: fix a missing check on list iterator
+    - net: atlantic: always deep reset on pm op, fixing up my null deref
+      regression
+    - net: phy: Fix race condition on link status change
+    - writeback: Avoid skipping inode writeback
+    - cgroup/cpuset: Remove cpus_allowed/mems_allowed setup in cpuset_init_smp()
+    - arm[64]/memremap: don't abuse pfn_valid() to ensure presence of linear map
+    - net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061
+    - net: phy: micrel: Pass .probe for KS8737
+    - SUNRPC: Ensure that the gssproxy client can start in a connected state
+    - drm/vmwgfx: Initialize drm_mode_fb_cmd2
+    - dma-buf: call dma_buf_stats_setup after dmabuf is in valid list
+    - mm/hwpoison: use pr_err() instead of dump_page() in get_any_page()
+    - ping: fix address binding wrt vrf
+    - usb: gadget: uvc: rename function to be more consistent
+    - usb: gadget: uvc: allow for application to cleanly shutdown
+    - Linux 5.15.41
+  * Jammy update: v5.15.40 upstream stable release (LP: #1980277)
+    - tools arch: Update arch/x86/lib/mem{cpy,set}_64.S copies used in 'perf bench
+      mem memcpy'
+    - Bluetooth: Fix the creation of hdev->name
+    - udf: Avoid using stale lengthOfImpUse
+    - mm: fix missing cache flush for all tail pages of compound page
+    - mm: hugetlb: fix missing cache flush in copy_huge_page_from_user()
+    - mm: shmem: fix missing cache flush in shmem_mfill_atomic_pte()
+    - mm: userfaultfd: fix missing cache flush in mcopy_atomic_pte() and
+      __mcopy_atomic()
+    - mm/hwpoison: fix error page recovered but reported "not recovered"
+    - mm/mlock: fix potential imbalanced rlimit ucounts adjustment
+    - mm: fix invalid page pointer returned with FOLL_PIN gups
+    - Linux 5.15.40
+
+  [ Ubuntu: 5.15.0-46.49 ]
+
+  * CVE-2022-2585
+    - SAUCE: posix-cpu-timers: Cleanup CPU timers before freeing them during exec
+  * CVE-2022-2586
+    - SAUCE: netfilter: nf_tables: do not allow SET_ID to refer to another table
+    - SAUCE: netfilter: nf_tables: do not allow CHAIN_ID to refer to another table
+    - SAUCE: netfilter: nf_tables: do not allow RULE_ID to refer to another chain
+  * CVE-2022-2588
+    - SAUCE: net_sched: cls_route: remove from list when handle is 0
+
+  [ Ubuntu: 5.15.0-45.48 ]
+
+  * CVE-2022-29900 // CVE-2022-29901
+    - x86/lib/atomic64_386_32: Rename things
+    - x86: Prepare asm files for straight-line-speculation
+    - x86: Prepare inline-asm for straight-line-speculation
+    - x86/alternative: Relax text_poke_bp() constraint
+    - kbuild: move objtool_args back to scripts/Makefile.build
+    - x86: Add straight-line-speculation mitigation
+    - kvm/emulate: Fix SETcc emulation function offsets with SLS
+    - crypto: x86/poly1305 - Fixup SLS
+    - objtool: Add straight-line-speculation validation
+    - objtool: Fix SLS validation for kcov tail-call replacement
+    - objtool: Fix objtool regression on x32 systems
+    - objtool: Fix symbol creation
+    - objtool: Introduce CFI hash
+    - objtool: Default ignore INT3 for unreachable
+    - x86, kvm: use proper ASM macros for kvm_vcpu_is_preempted
+    - x86/traps: Use pt_regs directly in fixup_bad_iret()
+    - x86/entry: Switch the stack after error_entry() returns
+    - x86/entry: Move PUSH_AND_CLEAR_REGS out of error_entry()
+    - x86/entry: Don't call error_entry() for XENPV
+    - x86/entry: Remove skip_r11rcx
+    - x86/realmode: build with -D__DISABLE_EXPORTS
+    - x86/ibt,ftrace: Make function-graph play nice
+    - x86/kvm/vmx: Make noinstr clean
+    - x86/cpufeatures: Move RETPOLINE flags to word 11
+    - x86/retpoline: Cleanup some #ifdefery
+    - x86/retpoline: Swizzle retpoline thunk
+    - x86/retpoline: Use -mfunction-return
+    - x86: Undo return-thunk damage
+    - x86,objtool: Create .return_sites
+    - objtool: skip non-text sections when adding return-thunk sites
+    - x86,static_call: Use alternative RET encoding
+    - x86/ftrace: Use alternative RET encoding
+    - x86/bpf: Use alternative RET encoding
+    - x86/kvm: Fix SETcc emulation for return thunks
+    - x86/vsyscall_emu/64: Don't use RET in vsyscall emulation
+    - x86/sev: Avoid using __x86_return_thunk
+    - x86: Use return-thunk in asm code
+    - x86/entry: Avoid very early RET
+    - objtool: Treat .text.__x86.* as noinstr
+    - x86: Add magic AMD return-thunk
+    - x86/bugs: Report AMD retbleed vulnerability
+    - x86/bugs: Add AMD retbleed= boot parameter
+    - x86/bugs: Enable STIBP for JMP2RET
+    - x86/bugs: Keep a per-CPU IA32_SPEC_CTRL value
+    - x86/entry: Add kernel IBRS implementation
+    - x86/bugs: Optimize SPEC_CTRL MSR writes
+    - x86/speculation: Add spectre_v2=ibrs option to support Kernel IBRS
+    - x86/bugs: Split spectre_v2_select_mitigation() and
+      spectre_v2_user_select_mitigation()
+    - x86/bugs: Report Intel retbleed vulnerability
+    - intel_idle: Disable IBRS during long idle
+    - objtool: Update Retpoline validation
+    - x86/xen: Rename SYS* entry points
+    - x86/xen: Add UNTRAIN_RET
+    - x86/bugs: Add retbleed=ibpb
+    - x86/bugs: Do IBPB fallback check only once
+    - objtool: Add entry UNRET validation
+    - x86/cpu/amd: Add Spectral Chicken
+    - x86/speculation: Fix RSB filling with CONFIG_RETPOLINE=n
+    - x86/speculation: Fix firmware entry SPEC_CTRL handling
+    - x86/speculation: Fix SPEC_CTRL write on SMT state change
+    - x86/speculation: Use cached host SPEC_CTRL value for guest entry/exit
+    - x86/speculation: Remove x86_spec_ctrl_mask
+    - objtool: Re-add UNWIND_HINT_{SAVE_RESTORE}
+    - KVM: VMX: Flatten __vmx_vcpu_run()
+    - KVM: VMX: Convert launched argument to flags
+    - KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS
+    - KVM: VMX: Fix IBRS handling after vmexit
+    - x86/speculation: Fill RSB on vmexit for IBRS
+    - KVM: VMX: Prevent RSB underflow before vmenter
+    - x86/common: Stamp out the stepping madness
+    - x86/cpu/amd: Enumerate BTC_NO
+    - x86/retbleed: Add fine grained Kconfig knobs
+    - x86/bugs: Add Cannon lake to RETBleed affected CPU list
+    - x86/entry: Move PUSH_AND_CLEAR_REGS() back into error_entry
+    - x86/bugs: Do not enable IBPB-on-entry when IBPB is not supported
+    - x86/kexec: Disable RET on kexec
+    - x86/speculation: Disable RRSBA behavior
+    - [Config]: Enable speculation mitigations
+    - x86/static_call: Serialize __static_call_fixup() properly
+    - x86/asm/32: Fix ANNOTATE_UNRET_SAFE use on 32-bit
+    - x86/bugs: Mark retbleed_strings static
+    - x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
+    - x86/kvm: fix FASTOP_SIZE when return thunks are enabled
+    - x86/speculation: Use DECLARE_PER_CPU for x86_spec_ctrl_current
+    - KVM: emulate: do not adjust size of fastop and setcc subroutines
+    - x86/bugs: Remove apostrophe typo
+    - efi/x86: use naked RET on mixed mode call wrapper
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 19 Jan 2023 11:15:52 +1000
+
+linux-xilinx-zynqmp (5.15.0-1018.20) jammy; urgency=medium
+
+  * ProvenCore TEE driver causes process stall on systems without secure-OS
+    - Revert "Import ProveCore TEE driver"
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 15 Dec 2022 21:24:04 +1000
+
+linux-xilinx-zynqmp (5.15.0-1017.18) jammy; urgency=medium
+
+  * mv-camera-sensor-module updated driver
+    - Update Xilinx mv-camera-sensor-module kernel module
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 15 Dec 2022 09:10:24 +1000
+
+linux-xilinx-zynqmp (5.15.0-1016.17) jammy; urgency=medium
+
+  * Integrate ProvenCore TEE kernel driver
+    - Import ProveCore TEE driver
+
+  * Miscellaneous upstream changes
+    - arm64: zynqmp: Skip frequency resetting of si570 clocks during probe
+    - net: macb: In ZynqMP resume always configure PS GTR for non-wakeup source
+    - spi: spi-zynqmp-gqspi: Fix call trace during QSPI suspend
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 30 Nov 2022 09:04:53 +1000
+
+linux-xilinx-zynqmp (5.15.0-1015.16) jammy; urgency=medium
+
+  * Enable new version of XRT kernel driver
+    - Update XRT 2022.1 kernel modules
+
+  * Failed to edit jammy kernel configuration with custom build flow
+    - [Config] upgrade debug symbols from DWARF4 to DWARF5
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update annotation to remove unnecessary settings
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 29 Sep 2022 09:58:53 +1000
+
+linux-xilinx-zynqmp (5.15.0-1014.15) jammy; urgency=medium
+
+  * Miscellaneous upstream changes
+    - clk: versalclock7: Use index to output mapping to reference banks
+    - dt-bindings: usb: dwc3: Add snps,xhci-reset-on-resume quirk
+    - usb: add quirk for xhci reinit warning on resume
+    - arm: dts: zynqmp: add snps,xhci-reset-on-resume quirk
+    - clk: versaclock7: Use a property to differentiate between nodes
+    - net: macb: In shared MDIO usecase make MDIO producer ethernet node to probe
+      first
+    - net: macb: Fix macb mdiobus handing for DT nodes without phy-handle
+    - net: macb: Fix ZynqMP SGMII non-wakeup source resume failure
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Tue, 30 Aug 2022 07:56:52 +0200
+
+linux-xilinx-zynqmp (5.15.0-1013.14) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1983604)
+    - Enable xilinx-isp-module kernel module
+
+  * INVALID or PRIVATE BUG (LP: #1983577)
+    - [Config] Enable CONFIG_VIDEO_XILINX_AXI4S_SUBSETCONV
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 11 Aug 2022 10:02:38 +1000
+
+linux-xilinx-zynqmp (5.15.0-1012.13) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enable do_enforce_all and update annotations
+    - [Config] Update configs
+
+  * Miscellaneous upstream changes
+    - arm64: zynqmp: Enable DP for kv260-revA board
+    - arm64: zynqmp: Fix usb node drive strength and slew rate
+    - dt-bindings: Renesas versaclock7 device tree bindings
+    - clk: versalclock7: Add Renesas versaclock7 ccf device driver
+    - xilinx: Enable renesas,versaclock7 driver
+    - drm: xlnx: mixer: Correct the fourcc string copy
+
+  [ Ubuntu: 5.15.0-43.46 ]
+
+  * jammy/linux: 5.15.0-43.46 -proposed tracker (LP: #1981243)
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2022.07.11)
+  * nbd: requests can become stuck when disconnecting from server with qemu-nbd
+    (LP: #1896350)
+    - nbd: don't handle response without a corresponding request message
+    - nbd: make sure request completion won't concurrent
+    - nbd: don't clear 'NBD_CMD_INFLIGHT' flag if request is not completed
+    - nbd: fix io hung while disconnecting device
+  * Ubuntu 22.04 and 20.04 DPC Fixes for Failure Cases of DownPort Containment
+    events (LP: #1965241)
+    - PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
+    - PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
+    - [Config] Enable config option CONFIG_PCIE_EDR
+  * [SRU] Ubuntu 22.04 Feature Request-Add support for a NVMe-oF-TCP CDC Client
+    - TP 8010 (LP: #1948626)
+    - nvme: add CNTRLTYPE definitions for 'identify controller'
+    - nvme: send uevent on connection up
+    - nvme: expose cntrltype and dctype through sysfs
+  * [UBUNTU 22.04] Kernel oops while removing device from cio_ignore list
+    (LP: #1980951)
+    - s390/cio: derive cdev information only for IO-subchannels
+  * Jammy Charmed OpenStack deployment fails over connectivity issues when using
+    converged OVS bridge for control and data planes (LP: #1978820)
+    - net/mlx5e: TC NIC mode, fix tc chains miss table
+  * Hairpin traffic does not work with centralized NAT gw (LP: #1967856)
+    - net: openvswitch: fix misuse of the cached connection on tuple changes
+  * alsa: asoc: amd: the internal mic can't be dedected on yellow carp machines
+    (LP: #1980700)
+    - ASoC: amd: Add driver data to acp6x machine driver
+    - ASoC: amd: Add support for enabling DMIC on acp6x via _DSD
+  * AMD ACP 6.x DMIC Supports (LP: #1949245)
+    - ASoC: amd: add Yellow Carp ACP6x IP register header
+    - ASoC: amd: add Yellow Carp ACP PCI driver
+    - ASoC: amd: add acp6x init/de-init functions
+    - ASoC: amd: add platform devices for acp6x pdm driver and dmic driver
+    - ASoC: amd: add acp6x pdm platform driver
+    - ASoC: amd: add acp6x irq handler
+    - ASoC: amd: add acp6x pdm driver dma ops
+    - ASoC: amd: add acp6x pci driver pm ops
+    - ASoC: amd: add acp6x pdm driver pm ops
+    - ASoC: amd: enable Yellow carp acp6x drivers build
+    - ASoC: amd: create platform device for acp6x machine driver
+    - ASoC: amd: add YC machine driver using dmic
+    - ASoC: amd: enable Yellow Carp platform machine driver build
+    - ASoC: amd: fix uninitialized variable in snd_acp6x_probe()
+    - [Config] Enable AMD ACP 6 DMIC Support
+  * [UBUNTU 20.04] Include patches to avoid self-detected stall with Secure
+    Execution (LP: #1979296)
+    - KVM: s390: pv: add macros for UVC CC values
+    - KVM: s390: pv: avoid stalls when making pages secure
+  * [22.04 FEAT] KVM: Attestation support for Secure Execution (crypto)
+    (LP: #1959973)
+    - drivers/s390/char: Add Ultravisor io device
+    - s390/uv_uapi: depend on CONFIG_S390
+    - [Config] CONFIG_S390_UV_UAPI=y for s390x
+  * CVE-2022-1679
+    - SAUCE: ath9k: fix use-after-free in ath9k_hif_usb_rx_cb
+  * CVE-2022-28893
+    - SUNRPC: Ensure we flush any closed sockets before xs_xprt_free()
+    - SUNRPC: Don't leak sockets in xs_local_connect()
+  * CVE-2022-34918
+    - netfilter: nf_tables: stricter validation of element data
+  * CVE-2022-1652
+    - floppy: use a statically allocated error counter
+
+  [ Ubuntu: 5.15.0-41.44 ]
+
+  * jammy/linux: 5.15.0-41.44 -proposed tracker (LP: #1979448)
+  * Fix can't boot up after change to vmd  (LP: #1976587)
+    - PCI: vmd: Assign VMD IRQ domain before enumeration
+    - PCI: vmd: Revert 2565e5b69c44 ("PCI: vmd: Do not disable MSI-X remapping if
+      interrupt remapping is enabled by IOMMU.")
+  * [SRU][Jammy/OEM-5.17][PATCH 0/1] Fix calltrace in mac80211 (LP: #1978297)
+    - mac80211: fix struct ieee80211_tx_info size
+  * [SRU][Jammy][PATCH 0/1] Fix amd display corruption on s2idle resume
+    (LP: #1978244)
+    - drm/amd/display: Don't reinitialize DMCUB on s0ix resume
+  * pl2303 serial adapter not recognized (LP: #1967493)
+    - USB: serial: pl2303: fix type detection for odd device
+  * Remove SAUCE patches from test_vxlan_under_vrf.sh in net of
+    ubuntu_kernel_selftests (LP: #1975691)
+    - Revert "UBUNTU: SAUCE: selftests: net: Don't fail test_vxlan_under_vrf on
+      xfail"
+    - Revert "UBUNTU: SAUCE: selftests: net: Make test for VXLAN underlay in non-
+      default VRF an expected failure"
+  * Fix hp_wmi_read_int() reporting error (0x05) (LP: #1979051)
+    - platform/x86: hp-wmi: Fix hp_wmi_read_int() reporting error (0x05)
+  * Request to back port vmci patches to Ubuntu kernel (LP: #1978145)
+    - VMCI: dma dg: whitespace formatting change for vmci register defines
+    - VMCI: dma dg: add MMIO access to registers
+    - VMCI: dma dg: detect DMA datagram capability
+    - VMCI: dma dg: set OS page size
+    - VMCI: dma dg: register dummy IRQ handlers for DMA datagrams
+    - VMCI: dma dg: allocate send and receive buffers for DMA datagrams
+    - VMCI: dma dg: add support for DMA datagrams sends
+    - VMCI: dma dg: add support for DMA datagrams receive
+    - VMCI: Fix some error handling paths in vmci_guest_probe_device()
+    - VMCI: Release notification_bitmap in error path
+    - VMCI: Check exclusive_vectors when freeing interrupt 1
+    - VMCI: Add support for ARM64
+    - [Config] Update policies for VMWARE_VMCI and VMWARE_VMCI_VSOCKETS
+  * [UBUNTU 20.04] rcu stalls with many storage key guests (LP: #1975582)
+    - s390/gmap: voluntarily schedule during key setting
+    - s390/mm: use non-quiescing sske for KVM switch to keyed guest
+  * [SRU][OEM-5.14/OEM-5.17/Jammy][PATCH 0/1] Fix i915 calltrace on new ADL BIOS
+    (LP: #1976214)
+    - drm/i915: update new TMDS clock setting defined by VBT
+  * Revert PPC get_user workaround (LP: #1976248)
+    - powerpc: Export mmu_feature_keys[] as non-GPL
+  * Jammy update: v5.15.39 upstream stable release (LP: #1978240)
+    - MIPS: Fix CP0 counter erratum detection for R4k CPUs
+    - parisc: Merge model and model name into one line in /proc/cpuinfo
+    - ALSA: hda/realtek: Add quirk for Yoga Duet 7 13ITL6 speakers
+    - ALSA: fireworks: fix wrong return count shorter than expected by 4 bytes
+    - mmc: sdhci-msm: Reset GCC_SDCC_BCR register for SDHC
+    - mmc: sunxi-mmc: Fix DMA descriptors allocated above 32 bits
+    - mmc: core: Set HS clock speed before sending HS CMD13
+    - gpiolib: of: fix bounds check for 'gpio-reserved-ranges'
+    - x86/fpu: Prevent FPU state corruption
+    - KVM: x86/svm: Account for family 17h event renumberings in
+      amd_pmc_perf_hw_id
+    - iommu/vt-d: Calculate mask for non-aligned flushes
+    - iommu/arm-smmu-v3: Fix size calculation in arm_smmu_mm_invalidate_range()
+    - drm/amd/display: Avoid reading audio pattern past AUDIO_CHANNELS_COUNT
+    - drm/amdgpu: do not use passthrough mode in Xen dom0
+    - RISC-V: relocate DTB if it's outside memory region
+    - Revert "SUNRPC: attempt AF_LOCAL connect on setup"
+    - timekeeping: Mark NMI safe time accessors as notrace
+    - firewire: fix potential uaf in outbound_phy_packet_callback()
+    - firewire: remove check of list iterator against head past the loop body
+    - firewire: core: extend card->lock in fw_core_handle_bus_reset
+    - net: stmmac: disable Split Header (SPH) for Intel platforms
+    - genirq: Synchronize interrupt thread startup
+    - ASoC: da7219: Fix change notifications for tone generator frequency
+    - ASoC: wm8958: Fix change notifications for DSP controls
+    - ASoC: meson: Fix event generation for AUI ACODEC mux
+    - ASoC: meson: Fix event generation for G12A tohdmi mux
+    - ASoC: meson: Fix event generation for AUI CODEC mux
+    - s390/dasd: fix data corruption for ESE devices
+    - s390/dasd: prevent double format of tracks for ESE devices
+    - s390/dasd: Fix read for ESE with blksize < 4k
+    - s390/dasd: Fix read inconsistency for ESE DASD devices
+    - can: grcan: grcan_close(): fix deadlock
+    - can: isotp: remove re-binding of bound socket
+    - can: grcan: use ofdev->dev when allocating DMA memory
+    - can: grcan: grcan_probe(): fix broken system id check for errata workaround
+      needs
+    - can: grcan: only use the NAPI poll budget for RX
+    - nfc: replace improper check device_is_registered() in netlink related
+      functions
+    - nfc: nfcmrvl: main: reorder destructive operations in
+      nfcmrvl_nci_unregister_dev to avoid bugs
+    - NFC: netlink: fix sleep in atomic bug when firmware download timeout
+    - gpio: visconti: Fix fwnode of GPIO IRQ
+    - gpio: pca953x: fix irq_stat not updated when irq is disabled (irq_mask not
+      set)
+    - hwmon: (adt7470) Fix warning on module removal
+    - hwmon: (pmbus) disable PEC if not enabled
+    - ASoC: dmaengine: Restore NULL prepare_slave_config() callback
+    - ASoC: soc-ops: fix error handling
+    - iommu/vt-d: Drop stop marker messages
+    - iommu/dart: check return value after calling platform_get_resource()
+    - net/mlx5e: Fix trust state reset in reload
+    - net/mlx5e: Don't match double-vlan packets if cvlan is not set
+    - net/mlx5e: CT: Fix queued up restore put() executing after relevant ft
+      release
+    - net/mlx5e: Fix the calling of update_buffer_lossy() API
+    - net/mlx5: Avoid double clear or set of sync reset requested
+    - net/mlx5: Fix deadlock in sync reset flow
+    - selftests/seccomp: Don't call read() on TTY from background pgrp
+    - SUNRPC release the transport of a relocated task with an assigned transport
+    - RDMA/siw: Fix a condition race issue in MPA request processing
+    - RDMA/irdma: Flush iWARP QP if modified to ERR from RTR state
+    - RDMA/irdma: Reduce iWARP QP destroy time
+    - RDMA/irdma: Fix possible crash due to NULL netdev in notifier
+    - NFSv4: Don't invalidate inode attributes on delegation return
+    - net: ethernet: mediatek: add missing of_node_put() in mtk_sgmii_init()
+    - net: dsa: mt7530: add missing of_node_put() in mt7530_setup()
+    - net: stmmac: dwmac-sun8i: add missing of_node_put() in
+      sun8i_dwmac_register_mdio_mux()
+    - net: mdio: Fix ENOMEM return value in BCM6368 mux bus controller
+    - net: cpsw: add missing of_node_put() in cpsw_probe_dt()
+    - net: igmp: respect RCU rules in ip_mc_source() and ip_mc_msfilter()
+    - net: emaclite: Add error handling for of_address_to_resource()
+    - selftests/net: so_txtime: fix parsing of start time stamp on 32 bit systems
+    - selftests/net: so_txtime: usage(): fix documentation of default clock
+    - drm/msm/dp: remove fail safe mode related code
+    - btrfs: do not BUG_ON() on failure to update inode when setting xattr
+    - hinic: fix bug of wq out of bound access
+    - mld: respect RCU rules in ip6_mc_source() and ip6_mc_msfilter()
+    - rxrpc: Enable IPv6 checksums on transport socket
+    - selftests: mirror_gre_bridge_1q: Avoid changing PVID while interface is
+      operational
+    - bnxt_en: Fix possible bnxt_open() failure caused by wrong RFS flag
+    - bnxt_en: Fix unnecessary dropping of RX packets
+    - selftests: ocelot: tc_flower_chains: specify conform-exceed action for
+      policer
+    - smsc911x: allow using IRQ0
+    - btrfs: force v2 space cache usage for subpage mount
+    - btrfs: always log symlinks in full mode
+    - gpio: mvebu: drop pwm base assignment
+    - kvm: x86/cpuid: Only provide CPUID leaf 0xA if host has architectural PMU
+    - net/mlx5: Fix slab-out-of-bounds while reading resource dump menu
+    - net/mlx5e: Lag, Fix use-after-free in fib event handler
+    - net/mlx5e: Lag, Fix fib_info pointer assignment
+    - net/mlx5e: Lag, Don't skip fib events on current dst
+    - iommu/dart: Add missing module owner to ops structure
+    - kvm: selftests: do not use bitfields larger than 32-bits for PTEs
+    - KVM: selftests: Silence compiler warning in the kvm_page_table_test
+    - x86/kvm: Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
+    - KVM: x86: Do not change ICR on write to APIC_SELF_IPI
+    - KVM: x86/mmu: avoid NULL-pointer dereference on page freeing bugs
+    - KVM: LAPIC: Enable timer posted-interrupt only when mwait/hlt is advertised
+    - selftest/vm: verify mmap addr in mremap_test
+    - selftest/vm: verify remap destination address in mremap_test
+    - Revert "parisc: Mark sched_clock unstable only if clocks are not
+      syncronized"
+    - rcu: Fix callbacks processing time limit retaining cond_resched()
+    - rcu: Apply callbacks processing time limit only on softirq
+    - PCI: pci-bridge-emul: Add description for class_revision field
+    - PCI: pci-bridge-emul: Add definitions for missing capabilities registers
+    - PCI: aardvark: Add support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
+      registers on emulated bridge
+    - PCI: aardvark: Clear all MSIs at setup
+    - PCI: aardvark: Comment actions in driver remove method
+    - PCI: aardvark: Disable bus mastering when unbinding driver
+    - PCI: aardvark: Mask all interrupts when unbinding driver
+    - PCI: aardvark: Fix memory leak in driver unbind
+    - PCI: aardvark: Assert PERST# when unbinding driver
+    - PCI: aardvark: Disable link training when unbinding driver
+    - PCI: aardvark: Disable common PHY when unbinding driver
+    - PCI: aardvark: Replace custom PCIE_CORE_INT_* macros with PCI_INTERRUPT_*
+    - PCI: aardvark: Check return value of generic_handle_domain_irq() when
+      processing INTx IRQ
+    - PCI: aardvark: Make MSI irq_chip structures static driver structures
+    - PCI: aardvark: Make msi_domain_info structure a static driver structure
+    - PCI: aardvark: Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node)
+    - PCI: aardvark: Refactor unmasking summary MSI interrupt
+    - PCI: aardvark: Add support for masking MSI interrupts
+    - PCI: aardvark: Fix setting MSI address
+    - PCI: aardvark: Enable MSI-X support
+    - PCI: aardvark: Add support for ERR interrupt on emulated bridge
+    - PCI: aardvark: Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on
+      emulated bridge
+    - PCI: aardvark: Add support for PME interrupts
+    - PCI: aardvark: Fix support for PME requester on emulated bridge
+    - PCI: aardvark: Use separate INTA interrupt for emulated root bridge
+    - PCI: aardvark: Remove irq_mask_ack() callback for INTx interrupts
+    - PCI: aardvark: Don't mask irq when mapping
+    - PCI: aardvark: Drop __maybe_unused from advk_pcie_disable_phy()
+    - PCI: aardvark: Update comment about link going down after link-up
+    - Linux 5.15.39
+  * Jammy update: v5.15.38 upstream stable release (LP: #1978234)
+    - usb: mtu3: fix USB 3.0 dual-role-switch from device to host
+    - USB: quirks: add a Realtek card reader
+    - USB: quirks: add STRING quirk for VCOM device
+    - USB: serial: whiteheat: fix heap overflow in WHITEHEAT_GET_DTR_RTS
+    - USB: serial: cp210x: add PIDs for Kamstrup USB Meter Reader
+    - USB: serial: option: add support for Cinterion MV32-WA/MV32-WB
+    - USB: serial: option: add Telit 0x1057, 0x1058, 0x1075 compositions
+    - usb: xhci: tegra:Fix PM usage reference leak of
+      tegra_xusb_unpowergate_partitions
+    - xhci: Enable runtime PM on second Alderlake controller
+    - xhci: stop polling roothubs after shutdown
+    - xhci: increase usb U3 -> U0 link resume timeout from 100ms to 500ms
+    - iio: dac: ad5592r: Fix the missing return value.
+    - iio: dac: ad5446: Fix read_raw not returning set value
+    - iio: magnetometer: ak8975: Fix the error handling in ak8975_power_on()
+    - iio: imu: inv_icm42600: Fix I2C init possible nack
+    - usb: misc: fix improper handling of refcount in uss720_probe()
+    - usb: core: Don't hold the device lock while sleeping in do_proc_control()
+    - usb: typec: ucsi: Fix reuse of completion structure
+    - usb: typec: ucsi: Fix role swapping
+    - usb: gadget: uvc: Fix crash when encoding data for usb request
+    - usb: gadget: configfs: clear deactivation flag in
+      configfs_composite_unbind()
+    - usb: dwc3: Try usb-role-switch first in dwc3_drd_init
+    - usb: dwc3: core: Fix tx/rx threshold settings
+    - usb: dwc3: core: Only handle soft-reset in DCTL
+    - usb: dwc3: gadget: Return proper request status
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-P
+    - usb: cdns3: Fix issue for clear halt endpoint
+    - usb: phy: generic: Get the vbus supply
+    - serial: imx: fix overrun interrupts in DMA mode
+    - serial: amba-pl011: do not time out prematurely when draining tx fifo
+    - serial: 8250: Also set sticky MCR bits in console restoration
+    - serial: 8250: Correct the clock for EndRun PTP/1588 PCIe device
+    - arch_topology: Do not set llc_sibling if llc_id is invalid
+    - ceph: fix possible NULL pointer dereference for req->r_session
+    - bus: mhi: host: pci_generic: Add missing poweroff() PM callback
+    - bus: mhi: host: pci_generic: Flush recovery worker during freeze
+    - arm64: dts: imx8mm-venice: fix spi2 pin configuration
+    - pinctrl: samsung: fix missing GPIOLIB on ARM64 Exynos config
+    - hex2bin: make the function hex_to_bin constant-time
+    - hex2bin: fix access beyond string end
+    - riscv: patch_text: Fixup last cpu should be master
+    - x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
+    - iocost: don't reset the inuse weight of under-weighted debtors
+    - virtio_net: fix wrong buf address calculation when using xdp
+    - cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
+    - cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
+    - video: fbdev: udlfb: properly check endpoint type
+    - arm64: dts: meson: remove CPU opps below 1GHz for G12B boards
+    - arm64: dts: meson: remove CPU opps below 1GHz for SM1 boards
+    - iio:imu:bmi160: disable regulator in error path
+    - mtd: rawnand: fix ecc parameters for mt7622
+    - xsk: Fix l2fwd for copy mode + busy poll combo
+    - arm64: dts: imx8qm: Correct SCU clock controller's compatible property
+    - USB: Fix xhci event ring dequeue pointer ERDP update issue
+    - ARM: dts: imx6qdl-apalis: Fix sgtl5000 detection issue
+    - arm64: dts: imx8mn: Fix SAI nodes
+    - arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO pin labeling for CON1
+    - phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe
+    - phy: samsung: exynos5250-sata: fix missing device put in probe error paths
+    - ARM: OMAP2+: Fix refcount leak in omap_gic_of_init
+    - bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific
+    - ARM: dts: dra7: Fix suspend warning for vpe powerdomain
+    - phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks
+    - ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
+    - ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
+    - ARM: dts: at91: fix pinctrl phandles
+    - phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe
+    - phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe
+    - interconnect: qcom: sdx55: Drop IP0 interconnects
+    - ARM: dts: Fix mmc order for omap3-gta04
+    - ARM: dts: am3517-evm: Fix misc pinmuxing
+    - ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
+    - ipvs: correctly print the memory size of ip_vs_conn_tab
+    - phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe()
+    - pinctrl: mediatek: moore: Fix build error
+    - mtd: rawnand: Fix return value check of wait_for_completion_timeout
+    - mtd: fix 'part' field data corruption in mtd_info
+    - pinctrl: stm32: Do not call stm32_gpio_get() for edge triggered IRQs in EOI
+    - memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
+    - net: dsa: Add missing of_node_put() in dsa_port_link_register_of
+    - netfilter: nft_set_rbtree: overlap detection with element re-addition after
+      deletion
+    - bpf, lwt: Fix crash when using bpf_skb_set_tunnel_key() from bpf_xmit lwt
+      hook
+    - pinctrl: rockchip: fix RK3308 pinmux bits
+    - tcp: md5: incorrect tcp_header_len for incoming connections
+    - pinctrl: stm32: Keep pinctrl block clock enabled when LEVEL IRQ requested
+    - tcp: ensure to use the most recently sent skb when filling the rate sample
+    - wireguard: device: check for metadata_dst with skb_valid_dst()
+    - sctp: check asoc strreset_chunk in sctp_generate_reconf_event
+    - ARM: dts: imx6ull-colibri: fix vqmmc regulator
+    - arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
+    - pinctrl: pistachio: fix use of irq_of_parse_and_map()
+    - cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
+    - net: hns3: clear inited state and stop client after failed to register
+      netdev
+    - net: hns3: modify the return code of hclge_get_ring_chain_from_mbx
+    - net: hns3: add validity check for message data length
+    - net: hns3: add return value for mailbox handling in PF
+    - net/smc: sync err code when tcp connection was refused
+    - ip_gre: Make o_seqno start from 0 in native mode
+    - ip6_gre: Make o_seqno start from 0 in native mode
+    - ip_gre, ip6_gre: Fix race condition on o_seqno in collect_md mode
+    - tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT
+    - tcp: make sure treq->af_specific is initialized
+    - bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
+    - clk: sunxi: sun9i-mmc: check return value after calling
+      platform_get_resource()
+    - cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
+    - net: bcmgenet: hide status block before TX timestamping
+    - net: phy: marvell10g: fix return value on error
+    - net: dsa: mv88e6xxx: Fix port_hidden_wait to account for port_base_addr
+    - drm/sun4i: Remove obsolete references to PHYS_OFFSET
+    - net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK
+    - io_uring: check reserved fields for send/sendmsg
+    - io_uring: check reserved fields for recv/recvmsg
+    - netfilter: conntrack: fix udp offload timeout sysctl
+    - drm/amdkfd: Fix GWS queue count
+    - drm/amd/display: Fix memory leak in dcn21_clock_source_create
+    - tls: Skip tls_append_frag on zero copy size
+    - bnx2x: fix napi API usage sequence
+    - net: fec: add missing of_node_put() in fec_enet_init_stop_mode()
+    - gfs2: Prevent endless loops in gfs2_file_buffered_write
+    - gfs2: Minor retry logic cleanup
+    - gfs2: Make sure not to return short direct writes
+    - gfs2: No short reads or writes upon glock contention
+    - perf arm-spe: Fix addresses of synthesized SPE events
+    - ixgbe: ensure IPsec VF<->PF compatibility
+    - Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"
+    - tcp: fix F-RTO may not work correctly when receiving DSACK
+    - ASoC: Intel: soc-acpi: correct device endpoints for max98373
+    - ASoC: wm8731: Disable the regulator when probing fails
+    - ext4: fix bug_on in start_this_handle during umount filesystem
+    - arch: xtensa: platforms: Fix deadlock in rs_close()
+    - ksmbd: increment reference count of parent fp
+    - ksmbd: set fixed sector size to FS_SECTOR_SIZE_INFORMATION
+    - bonding: do not discard lowest hash bit for non layer3+4 hashing
+    - x86: __memcpy_flushcache: fix wrong alignment if size > 2^32
+    - cifs: destage any unwritten data to the server before calling
+      copychunk_write
+    - drivers: net: hippi: Fix deadlock in rr_close()
+    - powerpc/perf: Fix 32bit compile
+    - selftest/vm: verify mmap addr in mremap_test
+    - selftest/vm: verify remap destination address in mremap_test
+    - Revert "ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40"
+    - zonefs: Fix management of open zones
+    - zonefs: Clear inode information flags on inode creation
+    - kasan: prevent cpu_quarantine corruption when CPU offline and cache shrink
+      occur at same time
+    - mtd: rawnand: qcom: fix memory corruption that causes panic
+    - netfilter: Update ip6_route_me_harder to consider L3 domain
+    - drm/i915: Check EDID for HDR static metadata when choosing blc
+    - drm/i915: Fix SEL_FETCH_PLANE_*(PIPE_B+) register addresses
+    - net: ethernet: stmmac: fix write to sgmii_adapter_base
+    - ACPI: processor: idle: Avoid falling back to C3 type C-states
+    - thermal: int340x: Fix attr.show callback prototype
+    - btrfs: fix leaked plug after failure syncing log on zoned filesystems
+    - ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
+    - ARM: dts: imx8mm-venice-gw{71xx,72xx,73xx}: fix OTG controller OC mode
+    - x86/cpu: Load microcode during restore_processor_state()
+    - perf symbol: Pass is_kallsyms to symbols__fixup_end()
+    - perf symbol: Update symbols__fixup_end()
+    - tty: n_gsm: fix restart handling via CLD command
+    - tty: n_gsm: fix decoupled mux resource
+    - tty: n_gsm: fix mux cleanup after unregister tty device
+    - tty: n_gsm: fix wrong signal octet encoding in convergence layer type 2
+    - tty: n_gsm: fix malformed counter for out of frame data
+    - netfilter: nft_socket: only do sk lookups when indev is available
+    - tty: n_gsm: fix insufficient txframe size
+    - tty: n_gsm: fix wrong DLCI release order
+    - tty: n_gsm: fix missing explicit ldisc flush
+    - tty: n_gsm: fix wrong command retry handling
+    - tty: n_gsm: fix wrong command frame length field encoding
+    - tty: n_gsm: fix wrong signal octets encoding in MSC
+    - tty: n_gsm: fix missing tty wakeup in convergence layer type 2
+    - tty: n_gsm: fix reset fifo race condition
+    - tty: n_gsm: fix incorrect UA handling
+    - tty: n_gsm: fix software flow control handling
+    - perf symbol: Remove arch__symbols__fixup_end()
+    - eeprom: at25: Use DMA safe buffers
+    - objtool: Fix code relocs vs weak symbols
+    - objtool: Fix type of reloc::addend
+    - powerpc/64: Add UADDR64 relocation support
+    - Linux 5.15.38
+  * Jammy update: v5.15.37 upstream stable release (LP: #1976135)
+    - floppy: disable FDRAWCMD by default
+    - [Config] updateconfigs for BLK_DEV_FD_RAWCMD
+    - bpf: Introduce composable reg, ret and arg types.
+    - bpf: Replace ARG_XXX_OR_NULL with ARG_XXX | PTR_MAYBE_NULL
+    - bpf: Replace RET_XXX_OR_NULL with RET_XXX | PTR_MAYBE_NULL
+    - bpf: Replace PTR_TO_XXX_OR_NULL with PTR_TO_XXX | PTR_MAYBE_NULL
+    - bpf: Introduce MEM_RDONLY flag
+    - bpf: Convert PTR_TO_MEM_OR_NULL to composable types.
+    - bpf: Make per_cpu_ptr return rdonly PTR_TO_MEM.
+    - bpf: Add MEM_RDONLY for helper args that are pointers to rdonly mem.
+    - bpf/selftests: Test PTR_TO_RDONLY_MEM
+    - bpf: Fix crash due to out of bounds access into reg2btf_ids.
+    - spi: cadence-quadspi: fix write completion support
+    - ARM: dts: socfpga: change qspi to "intel,socfpga-qspi"
+    - mm: kfence: fix objcgs vector allocation
+    - gup: Turn fault_in_pages_{readable,writeable} into
+      fault_in_{readable,writeable}
+    - iov_iter: Turn iov_iter_fault_in_readable into fault_in_iov_iter_readable
+    - iov_iter: Introduce fault_in_iov_iter_writeable
+    - gfs2: Add wrapper for iomap_file_buffered_write
+    - gfs2: Clean up function may_grant
+    - gfs2: Introduce flag for glock holder auto-demotion
+    - gfs2: Move the inode glock locking to gfs2_file_buffered_write
+    - gfs2: Eliminate ip->i_gh
+    - gfs2: Fix mmap + page fault deadlocks for buffered I/O
+    - iomap: Fix iomap_dio_rw return value for user copies
+    - iomap: Support partial direct I/O on user copy failures
+    - iomap: Add done_before argument to iomap_dio_rw
+    - gup: Introduce FOLL_NOFAULT flag to disable page faults
+    - iov_iter: Introduce nofault flag to disable page faults
+    - gfs2: Fix mmap + page fault deadlocks for direct I/O
+    - btrfs: fix deadlock due to page faults during direct IO reads and writes
+    - btrfs: fallback to blocking mode when doing async dio over multiple extents
+    - mm: gup: make fault_in_safe_writeable() use fixup_user_fault()
+    - selftests/bpf: Add test for reg2btf_ids out of bounds access
+    - Linux 5.15.37
+  * CVE-2022-1789
+    - KVM: x86/mmu: fix NULL pointer dereference on guest INVPCID
+  * Jammy update: v5.15.36 upstream stable release (LP: #1972905)
+    - block: simplify the block device syncing code
+    - xfs: return errors in xfs_fs_sync_fs
+    - dma-mapping: remove bogus test for pfn_valid from dma_map_resource
+    - arm64/mm: drop HAVE_ARCH_PFN_VALID
+    - etherdevice: Adjust ether_addr* prototypes to silence -Wstringop-overead
+    - mm: page_alloc: fix building error on -Werror=array-compare
+    - perf tools: Fix segfault accessing sample_id xyarray
+    - mm, kfence: support kmem_dump_obj() for KFENCE objects
+    - gfs2: assign rgrp glock before compute_bitstructs
+    - scsi: ufs: core: scsi_get_lba() error fix
+    - ALSA: usb-audio: Clear MIDI port active flag after draining
+    - ALSA: hda/realtek: Add quirk for Clevo NP70PNP
+    - ASoC: atmel: Remove system clock tree configuration for at91sam9g20ek
+    - ASoC: topology: Correct error handling in soc_tplg_dapm_widget_create()
+    - ASoC: rk817: Use devm_clk_get() in rk817_platform_probe
+    - ASoC: msm8916-wcd-digital: Check failure for devm_snd_soc_register_component
+    - ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use
+    - dmaengine: idxd: fix device cleanup on disable
+    - dmaengine: imx-sdma: Fix error checking in sdma_event_remap
+    - dmaengine: mediatek:Fix PM usage reference leak of
+      mtk_uart_apdma_alloc_chan_resources
+    - dmaengine: dw-edma: Fix unaligned 64bit access
+    - spi: spi-mtk-nor: initialize spi controller after resume
+    - esp: limit skb_page_frag_refill use to a single page
+    - spi: cadence-quadspi: fix incorrect supports_op() return value
+    - igc: Fix infinite loop in release_swfw_sync
+    - igc: Fix BUG: scheduling while atomic
+    - igc: Fix suspending when PTM is active
+    - ALSA: hda/hdmi: fix warning about PCM count when used with SOF
+    - rxrpc: Restore removed timer deletion
+    - net/smc: Fix sock leak when release after smc_shutdown()
+    - net/packet: fix packet_sock xmit return value checking
+    - ip6_gre: Avoid updating tunnel->tun_hlen in __gre6_xmit()
+    - ip6_gre: Fix skb_under_panic in __gre6_xmit()
+    - net: restore alpha order to Ethernet devices in config
+    - net/sched: cls_u32: fix possible leak in u32_init_knode()
+    - l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using
+      netdev_master_upper_dev_get_rcu
+    - ipv6: make ip6_rt_gc_expire an atomic_t
+    - can: isotp: stop timeout monitoring when no first frame was sent
+    - net: dsa: hellcreek: Calculate checksums in tagger
+    - net: mscc: ocelot: fix broken IP multicast flooding
+    - netlink: reset network and mac headers in netlink_dump()
+    - drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in
+      intel_psr2_config_valid() fails
+    - net: stmmac: Use readl_poll_timeout_atomic() in atomic state
+    - dmaengine: idxd: add RO check for wq max_batch_size write
+    - dmaengine: idxd: add RO check for wq max_transfer_size write
+    - dmaengine: idxd: skip clearing device context when device is read-only
+    - selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
+    - arm64: mm: fix p?d_leaf()
+    - ARM: vexpress/spc: Avoid negative array index when !SMP
+    - reset: renesas: Check return value of reset_control_deassert()
+    - reset: tegra-bpmp: Restore Handle errors in BPMP response
+    - platform/x86: samsung-laptop: Fix an unsigned comparison which can never be
+      negative
+    - ALSA: usb-audio: Fix undefined behavior due to shift overflowing the
+      constant
+    - drm/msm/disp: check the return value of kzalloc()
+    - arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
+    - vxlan: fix error return code in vxlan_fdb_append
+    - cifs: Check the IOCB_DIRECT flag, not O_DIRECT
+    - mt76: Fix undefined behavior due to shift overflowing the constant
+    - brcmfmac: sdio: Fix undefined behavior due to shift overflowing the constant
+    - dpaa_eth: Fix missing of_node_put in dpaa_get_ts_info()
+    - drm/msm/mdp5: check the return of kzalloc()
+    - net: macb: Restart tx only if queue pointer is lagging
+    - scsi: iscsi: Release endpoint ID when its freed
+    - scsi: iscsi: Merge suspend fields
+    - scsi: iscsi: Fix NOP handling during conn recovery
+    - scsi: qedi: Fix failed disconnect handling
+    - stat: fix inconsistency between struct stat and struct compat_stat
+    - VFS: filename_create(): fix incorrect intent.
+    - nvme: add a quirk to disable namespace identifiers
+    - nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
+    - nvme-pci: disable namespace identifiers for Qemu controllers
+    - EDAC/synopsys: Read the error count from the correct register
+    - mm/memory-failure.c: skip huge_zero_page in memory_failure()
+    - memcg: sync flush only if periodic flush is delayed
+    - mm, hugetlb: allow for "high" userspace addresses
+    - oom_kill.c: futex: delay the OOM reaper to allow time for proper futex
+      cleanup
+    - mm/mmu_notifier.c: fix race in mmu_interval_notifier_remove()
+    - ata: pata_marvell: Check the 'bmdma_addr' beforing reading
+    - dma: at_xdmac: fix a missing check on list iterator
+    - dmaengine: imx-sdma: fix init of uart scripts
+    - net: atlantic: invert deep par in pm functions, preventing null derefs
+    - Input: omap4-keypad - fix pm_runtime_get_sync() error checking
+    - scsi: sr: Do not leak information in ioctl
+    - sched/pelt: Fix attach_entity_load_avg() corner case
+    - perf/core: Fix perf_mmap fail when CONFIG_PERF_USE_VMALLOC enabled
+    - drm/panel/raspberrypi-touchscreen: Avoid NULL deref if not initialised
+    - drm/panel/raspberrypi-touchscreen: Initialise the bridge in prepare
+    - KVM: PPC: Fix TCE handling for VFIO
+    - drm/vc4: Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
+    - powerpc/perf: Fix power9 event alternatives
+    - powerpc/perf: Fix power10 event alternatives
+    - perf script: Always allow field 'data_src' for auxtrace
+    - perf report: Set PERF_SAMPLE_DATA_SRC bit for Arm SPE event
+    - xtensa: patch_text: Fixup last cpu should be master
+    - xtensa: fix a7 clobbering in coprocessor context load/store
+    - openvswitch: fix OOB access in reserve_sfa_size()
+    - ASoC: soc-dapm: fix two incorrect uses of list iterator
+    - e1000e: Fix possible overflow in LTR decoding
+    - ARC: entry: fix syscall_trace_exit argument
+    - arm_pmu: Validate single/group leader events
+    - KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
+    - KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
+    - KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
+    - KVM: SVM: Flush when freeing encrypted pages even on SME_COHERENT CPUs
+    - netfilter: conntrack: convert to refcount_t api
+    - netfilter: conntrack: avoid useless indirection during conntrack destruction
+    - ext4: fix fallocate to use file_modified to update permissions consistently
+    - ext4: fix symlink file size not match to file content
+    - ext4: fix use-after-free in ext4_search_dir
+    - ext4, doc: fix incorrect h_reserved size
+    - ext4: fix overhead calculation to account for the reserved gdt blocks
+    - ext4: force overhead calculation if the s_overhead_cluster makes no sense
+    - netfilter: nft_ct: fix use after free when attaching zone template
+    - jbd2: fix a potential race while discarding reserved buffers after an abort
+    - spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and
+      controller
+    - block/compat_ioctl: fix range check in BLKGETSIZE
+    - arm64: dts: qcom: add IPA qcom,qmp property
+    - Linux 5.15.36
+  * Aquantia GbE LAN driver causes UBSAN error during kernel boot
+    (LP: #1958770) // Jammy update: v5.15.36 upstream stable release
+    (LP: #1972905)
+    - net: atlantic: Avoid out-of-bounds indexing
+
+  [ Ubuntu: 5.15.0-40.43 ]
+
+  * jammy/linux: 5.15.0-40.43 -proposed tracker (LP: #1978610)
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2022.05.30)
+  * [SRU][OEM-5.14/OEM-5.17/J][PATCH 0/2] Fix system hangs after s2idle on AMD
+    A+A GPU (LP: #1975804)
+    - Revert "drm/amd/pm: keep the BACO feature enabled for suspend"
+    - drm/amd: Don't reset dGPUs if the system is going to s2idle
+  * [SRU][OEM-5.14/OEM-5.17/J][PATCH 0/1] Read the discovery registers for
+    AMD_SFH (LP: #1975798)
+    - HID: amd_sfh: Add support for sensor discovery
+  * [UBUNTU 20.04] CPU-MF: add extended counter set definitions for new IBM z16
+    (LP: #1974433)
+    - s390/cpumf: add new extended counter set for IBM z16
+  * [UBUNTU 20.04] KVM nesting support leaks too much memory, might result in
+    stalls during cleanup (LP: #1974017)
+    - KVM: s390: vsie/gmap: reduce gmap_rmap overhead
+  * [UBUNTU 20.04] Null Pointer issue in nfs code running Ubuntu on IBM Z
+    (LP: #1968096)
+    - NFS: Fix up nfs_ctx_key_to_expire()
+  * Fix REG_WAIT timeout for Yellow Carp (LP: #1971417)
+    - drm/amd/display: Clear encoder assignments when state cleared.
+    - drm/amd/display: fix stale info in link encoder assignment
+    - drm/amd/display: Query all entries in assignment table during updates.
+    - drm/amd/display: Initialise encoder assignment when initialising dc_state
+  * Enable hotspot feature for Realtek 8821CE (LP: #1969326)
+    - rtw88: Add update beacon flow for AP mode
+    - rtw88: 8821c: Enable TX report for management frames
+    - rtw88: do PHY calibration while starting AP
+    - rtw88: 8821c: fix debugfs rssi value
+    - rtw88: add ieee80211:sta_rc_update ops
+  * prevent kernel panic with overlayfs + shiftfs (LP: #1973620)
+    - SAUCE: overlayfs: prevent dereferencing struct file in ovl_vm_prfile_set()
+  * disable Intel DMA remapping by default (LP: #1971699)
+    - Revert "UBUNTU: [Config] enable Intel DMA remapping options by default"
+  * Mute/mic LEDs no function on Elitebook 630 (LP: #1974111)
+    - ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machine
+  * [Regression] Real-time Kernel Build Failure (LP: #1972899)
+    - x86/mm: Include spinlock_t definition in pgtable.
+  * build backport-iwlwifi-dkms as linux-modules-iwlwifi-ABI (LP: #1969434)
+    - [Packaging] support standalone dkms module builds
+    - [Packaging] drop do_<mod> arch specific configs
+  * IPU6 camera has no function on Andrews MLK (LP: #1964983)
+    - SAUCE: IPU6: 2022-03-11 alpha release for Andrews MLK
+    - [Config] IPU6: enable OV02C10 sensor
+    - SAUCE: IPU6: 2022-04-01 Andrews MLK PV release
+    - SAUCE: spi: ljca: return when a sub-transaction first failed
+    - SACUE: ljca: disable parallelly stub write
+    - SAUCE: ljca: fix race condition issue in runtime PM
+    - SAUCE: i2c-ljca: fix a null pointer access issue on tgl
+    - SAUCE: ljca: fix a typo issue
+    - SAUCE: ljca: assume stub enum failed as a warning
+    - SAUCE: mei: cleanup header file including
+    - SAUCE: intel_ulpss: Replaced by LJCA and remove
+    - [Config] drop intel_ulpss in favor of by LJCA
+  * multiple UBSAN warnings in Intel IPU6 camera driver at boot (LP: #1958006)
+    - SAUCE: media: pci: intel: Avoid UBSAN warnings of index bound and shift
+  * Support Intel IPU6 MIPI camera on Alder Lake platforms (LP: #1955383)
+    - SAUCE: intel ipu drivers first release
+    - SAUCE: IPU driver release WW48
+    - SAUCE: IPU driver release WW48 with MCU
+    - SAUCE: IPU driver release WW52
+    - SAUCE: IPU driver release WW04
+    - SAUCE: IPU driver release WW14
+    - SAUCE: Fix ov01a1s output mirror issue
+    - SAUCE: integrate IPU6 builds
+    - [Config] updateconfigs for IPU6 driver
+    - SAUCE: Fix ov01a1s IQ issues
+    - SAUCE: intel/ipu6: Remove unnecessary video devices
+    - SAUCE: change power control driver to acpi driver
+    - SAUCE: IPU6 driver release for kernel 5.13
+    - SAUCE: sensor HM11b1 brightness bugfix
+    - SAUCE: Fix build error on Kernel 5.13
+    - SAUCE: IPU6 driver release for kernel 5.14 on 2021-11-01
+    - [Config] IPU6: enable OV01A10 sensor
+    - SAUCE: Fix build error for kernel 5.15
+    - SAUCE: intel visual sensing controller(VSC) driver first release
+    - [Config] ivsc: enable Intel VSC drivers
+    - SAUCE: ivsc: return error when device not ready
+    - SAUCE: ivsc: add soft dependencies for intel_vsc module
+    - SAUCE: ljca: switch wait event to uninterruptible
+    - SAUCE: mei-vsc: switch wait event to uninterruptible
+    - SAUCE: mei_vsc: add ACPI HID for ADL
+    - SAUCE: ljca: add multi ACPI HID support
+    - SAUCE: ivsc: add delay for acquire camera to wait firmware ready
+    - SAUCE: mei_vsc: distinguish platform with different camera sensor
+    - SAUCE: i2c-ljca: fix a potential issue
+    - SAUCE: ljca: disable autosuspend by default
+    - [Config] make Intel IPU6 modules amd64 only
+    - SAUCE: IPU6: drop unnecessary cflags manipulation
+
+  [ Ubuntu: 5.15.0-39.42 ]
+
+  * CVE-2022-21123 // CVE-2022-21125 // CVE-2022-21166
+    - Documentation: Add documentation for Processor MMIO Stale Data
+    - x86/speculation/mmio: Enumerate Processor MMIO Stale Data bug
+    - x86/speculation: Add a common function for MD_CLEAR mitigation update
+    - x86/speculation/mmio: Add mitigation for Processor MMIO Stale Data
+    - x86/bugs: Group MDS, TAA & Processor MMIO Stale Data mitigations
+    - x86/speculation/mmio: Enable CPU Fill buffer clearing on idle
+    - x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data
+    - x86/speculation/srbds: Update SRBDS mitigation selection
+    - x86/speculation/mmio: Reuse SRBDS mitigation for SBDS
+    - KVM: x86/speculation: Disable Fill buffer clear within guests
+    - x86/speculation/mmio: Print SMT warning
+
+  [ Ubuntu: 5.15.0-37.39 ]
+
+  * netfilter newset OOB write (LP: #1976363)
+    - netfilter: nf_tables: sanitize nft_set_desc_concat_parse()
+  * CVE-2022-1966
+    - netfilter: nf_tables: disallow non-stateful expression in sets earlier
+
+  [ Ubuntu: 5.15.0-35.36 ]
+
+  * CVE-2022-21499
+    - SAUCE: debug: Lock down kgdb
+
+  [ Ubuntu: 5.15.0-34.35 ]
+
+  * jammy/linux: 5.15.0-34.35 -proposed tracker (LP: #1974322)
+  * AMD APU s2idle is broken after the ASIC reset fix (LP: #1972134)
+    - drm/amdgpu: unify BO evicting method in amdgpu_ttm
+    - drm/amdgpu: explicitly check for s0ix when evicting resources
+  * amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517
+    (LP: #1971597)
+    - gpio: Request interrupts after IRQ is initialized
+  * config CONFIG_HISI_PMU for  kunpeng920 (LP: #1956086)
+    - [Config] CONFIG_HISI_PMU=m
+  * Mute/mic LEDs no function on EliteBook G9 platfroms (LP: #1970552)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs support for HP Laptops
+  * network-manager/1.36.4-2ubuntu1 ADT test failure with linux/5.15.0-28.29
+    (LP: #1971418)
+    - Revert "rfkill: make new event layout opt-in"
+  * PCIE LnkCtl ASPM not enabled under VMD mode for Alder Lake platforms
+    (LP: #1942160)
+    - SAUCE: vmd: fixup bridge ASPM by driver name instead
+  * Mute/mic LEDs no function on HP EliteBook 845/865 G9 (LP: #1970178)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook
+      845/865 G9
+  * Enable headset mic on Lenovo P360 (LP: #1967069)
+    - ALSA: hda/realtek: Enable headset mic on Lenovo P360
+  * WCN6856 BT keep in OFF state after coldboot system (LP: #1967067)
+    - Bluetooth: btusb: Improve stability for QCA devices
+  * Screen sometimes can't update [Failed to post KMS update: CRTC property
+    (GAMMA_LUT) not found] (LP: #1967274)
+    - drm/i915/xelpd: Enable Pipe color support for D13 platform
+    - drm/i915: Use unlocked register accesses for LUT loads
+    - drm/i915/xelpd: Enable Pipe Degamma
+    - drm/i915/xelpd: Add Pipe Color Lut caps to platform config
+  * Jammy update: v5.15.35 upstream stable release (LP: #1969857)
+    - drm/amd/display: Add pstate verification and recovery for DCN31
+    - drm/amd/display: Fix p-state allow debug index on dcn31
+    - hamradio: defer 6pack kfree after unregister_netdev
+    - hamradio: remove needs_free_netdev to avoid UAF
+    - cpuidle: PSCI: Move the `has_lpi` check to the beginning of the function
+    - ACPI: processor idle: Check for architectural support for LPI
+    - ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40
+    - btrfs: remove unused parameter nr_pages in add_ra_bio_pages()
+    - btrfs: remove no longer used counter when reading data page
+    - btrfs: remove unused variable in btrfs_{start,write}_dirty_block_groups()
+    - soc: qcom: aoss: Expose send for generic usecase
+    - dt-bindings: net: qcom,ipa: add optional qcom,qmp property
+    - net: ipa: request IPA register values be retained
+    - btrfs: release correct delalloc amount in direct IO write path
+    - ALSA: core: Add snd_card_free_on_error() helper
+    - ALSA: sis7019: Fix the missing error handling
+    - ALSA: ali5451: Fix the missing snd_card_free() call at probe error
+    - ALSA: als300: Fix the missing snd_card_free() call at probe error
+    - ALSA: als4000: Fix the missing snd_card_free() call at probe error
+    - ALSA: atiixp: Fix the missing snd_card_free() call at probe error
+    - ALSA: au88x0: Fix the missing snd_card_free() call at probe error
+    - ALSA: aw2: Fix the missing snd_card_free() call at probe error
+    - ALSA: azt3328: Fix the missing snd_card_free() call at probe error
+    - ALSA: bt87x: Fix the missing snd_card_free() call at probe error
+    - ALSA: ca0106: Fix the missing snd_card_free() call at probe error
+    - ALSA: cmipci: Fix the missing snd_card_free() call at probe error
+    - ALSA: cs4281: Fix the missing snd_card_free() call at probe error
+    - ALSA: cs5535audio: Fix the missing snd_card_free() call at probe error
+    - ALSA: echoaudio: Fix the missing snd_card_free() call at probe error
+    - ALSA: emu10k1x: Fix the missing snd_card_free() call at probe error
+    - ALSA: ens137x: Fix the missing snd_card_free() call at probe error
+    - ALSA: es1938: Fix the missing snd_card_free() call at probe error
+    - ALSA: es1968: Fix the missing snd_card_free() call at probe error
+    - ALSA: fm801: Fix the missing snd_card_free() call at probe error
+    - ALSA: galaxy: Fix the missing snd_card_free() call at probe error
+    - ALSA: hdsp: Fix the missing snd_card_free() call at probe error
+    - ALSA: hdspm: Fix the missing snd_card_free() call at probe error
+    - ALSA: ice1724: Fix the missing snd_card_free() call at probe error
+    - ALSA: intel8x0: Fix the missing snd_card_free() call at probe error
+    - ALSA: intel_hdmi: Fix the missing snd_card_free() call at probe error
+    - ALSA: korg1212: Fix the missing snd_card_free() call at probe error
+    - ALSA: lola: Fix the missing snd_card_free() call at probe error
+    - ALSA: lx6464es: Fix the missing snd_card_free() call at probe error
+    - ALSA: maestro3: Fix the missing snd_card_free() call at probe error
+    - ALSA: oxygen: Fix the missing snd_card_free() call at probe error
+    - ALSA: riptide: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme32: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme9652: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme96: Fix the missing snd_card_free() call at probe error
+    - ALSA: sc6000: Fix the missing snd_card_free() call at probe error
+    - ALSA: sonicvibes: Fix the missing snd_card_free() call at probe error
+    - ALSA: via82xx: Fix the missing snd_card_free() call at probe error
+    - ALSA: usb-audio: Cap upper limits of buffer/period bytes for implicit fb
+    - ALSA: nm256: Don't call card private_free at probe error path
+    - drm/msm: Add missing put_task_struct() in debugfs path
+    - firmware: arm_scmi: Remove clear channel call on the TX channel
+    - memory: atmel-ebi: Fix missing of_node_put in atmel_ebi_probe
+    - Revert "ath11k: mesh: add support for 256 bitmap in blockack frames in 11ax"
+    - firmware: arm_scmi: Fix sorting of retrieved clock rates
+    - media: rockchip/rga: do proper error checking in probe
+    - SUNRPC: Fix the svc_deferred_event trace class
+    - net/sched: flower: fix parsing of ethertype following VLAN header
+    - veth: Ensure eth header is in skb's linear part
+    - gpiolib: acpi: use correct format characters
+    - cifs: release cached dentries only if mount is complete
+    - net: mdio: don't defer probe forever if PHY IRQ provider is missing
+    - mlxsw: i2c: Fix initialization error flow
+    - net/sched: fix initialization order when updating chain 0 head
+    - net: dsa: felix: suppress -EPROBE_DEFER errors
+    - net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link
+    - net/sched: taprio: Check if socket flags are valid
+    - cfg80211: hold bss_lock while updating nontrans_list
+    - netfilter: nft_socket: make cgroup match work in input too
+    - drm/msm: Fix range size vs end confusion
+    - drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()
+    - drm/msm/dp: add fail safe mode outside of event_mutex context
+    - net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
+    - scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
+    - scsi: pm80xx: Enable upper inbound, outbound queues
+    - scsi: iscsi: Move iscsi_ep_disconnect()
+    - scsi: iscsi: Fix offload conn cleanup when iscsid restarts
+    - scsi: iscsi: Fix endpoint reuse regression
+    - scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
+    - scsi: iscsi: Fix unbound endpoint error handling
+    - sctp: Initialize daddr on peeled off socket
+    - netfilter: nf_tables: nft_parse_register can return a negative value
+    - ALSA: ad1889: Fix the missing snd_card_free() call at probe error
+    - ALSA: mtpav: Don't call card private_free at probe error path
+    - io_uring: move io_uring_rsrc_update2 validation
+    - io_uring: verify that resv2 is 0 in io_uring_rsrc_update2
+    - io_uring: verify pad field is 0 in io_get_ext_arg
+    - testing/selftests/mqueue: Fix mq_perf_tests to free the allocated cpu set
+    - ALSA: usb-audio: Increase max buffer size
+    - ALSA: usb-audio: Limit max buffer and period sizes per time
+    - perf tools: Fix misleading add event PMU debug message
+    - macvlan: Fix leaking skb in source mode with nodst option
+    - net: ftgmac100: access hardware register after clock ready
+    - nfc: nci: add flush_workqueue to prevent uaf
+    - cifs: potential buffer overflow in handling symlinks
+    - dm mpath: only use ktime_get_ns() in historical selector
+    - vfio/pci: Fix vf_token mechanism when device-specific VF drivers are used
+    - net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
+    - block: fix offset/size check in bio_trim()
+    - drm/amd: Add USBC connector ID
+    - btrfs: fix fallocate to use file_modified to update permissions consistently
+    - btrfs: do not warn for free space inode in cow_file_range
+    - drm/amdgpu: conduct a proper cleanup of PDB bo
+    - drm/amdgpu/gmc: use PCI BARs for APUs in passthrough
+    - drm/amd/display: fix audio format not updated after edid updated
+    - drm/amd/display: FEC check in timing validation
+    - drm/amd/display: Update VTEM Infopacket definition
+    - drm/amdkfd: Fix Incorrect VMIDs passed to HWS
+    - drm/amdgpu/vcn: improve vcn dpg stop procedure
+    - drm/amdkfd: Check for potential null return of kmalloc_array()
+    - Drivers: hv: vmbus: Deactivate sysctl_record_panic_msg by default in
+      isolated guests
+    - PCI: hv: Propagate coherence from VMbus device to PCI device
+    - Drivers: hv: vmbus: Prevent load re-ordering when reading ring buffer
+    - scsi: target: tcmu: Fix possible page UAF
+    - scsi: lpfc: Fix queue failures when recovering from PCI parity error
+    - scsi: ibmvscsis: Increase INITIAL_SRP_LIMIT to 1024
+    - net: micrel: fix KS8851_MLL Kconfig
+    - ata: libata-core: Disable READ LOG DMA EXT for Samsung 840 EVOs
+    - gpu: ipu-v3: Fix dev_dbg frequency output
+    - regulator: wm8994: Add an off-on delay for WM8994 variant
+    - arm64: alternatives: mark patch_alternative() as `noinstr`
+    - tlb: hugetlb: Add more sizes to tlb_remove_huge_tlb_entry
+    - net: axienet: setup mdio unconditionally
+    - Drivers: hv: balloon: Disable balloon and hot-add accordingly
+    - net: usb: aqc111: Fix out-of-bounds accesses in RX fixup
+    - myri10ge: fix an incorrect free for skb in myri10ge_sw_tso
+    - spi: cadence-quadspi: fix protocol setup for non-1-1-X operations
+    - drm/amd/display: Enable power gating before init_pipes
+    - drm/amd/display: Revert FEC check in validation
+    - drm/amd/display: Fix allocate_mst_payload assert on resume
+    - drbd: set QUEUE_FLAG_STABLE_WRITES
+    - scsi: mpt3sas: Fail reset operation if config request timed out
+    - scsi: mvsas: Add PCI ID of RocketRaid 2640
+    - scsi: megaraid_sas: Target with invalid LUN ID is deleted during scan
+    - drivers: net: slip: fix NPD bug in sl_tx_timeout()
+    - io_uring: zero tag on rsrc removal
+    - io_uring: use nospec annotation for more indexes
+    - perf/imx_ddr: Fix undefined behavior due to shift overflowing the constant
+    - mm/secretmem: fix panic when growing a memfd_secret
+    - mm, page_alloc: fix build_zonerefs_node()
+    - mm: fix unexpected zeroed page mapping with zram swap
+    - mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
+    - KVM: x86/mmu: Resolve nx_huge_pages when kvm.ko is loaded
+    - SUNRPC: Fix NFSD's request deferral on RDMA transports
+    - memory: renesas-rpc-if: fix platform-device leak in error path
+    - gcc-plugins: latent_entropy: use /dev/urandom
+    - cifs: verify that tcon is valid before dereference in cifs_kill_sb
+    - ath9k: Properly clear TX status area before reporting to mac80211
+    - ath9k: Fix usage of driver-private space in tx_info
+    - btrfs: fix root ref counts in error handling in btrfs_get_root_ref
+    - btrfs: mark resumed async balance as writing
+    - ALSA: hda/realtek: Add quirk for Clevo PD50PNT
+    - ALSA: hda/realtek: add quirk for Lenovo Thinkpad X12 speakers
+    - ALSA: pcm: Test for "silence" field in struct "pcm_format_data"
+    - nl80211: correctly check NL80211_ATTR_REG_ALPHA2 size
+    - ipv6: fix panic when forwarding a pkt with no in6 dev
+    - drm/amd/display: don't ignore alpha property on pre-multiplied mode
+    - drm/amdgpu: Enable gfxoff quirk on MacBook Pro
+    - x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits
+    - x86/tsx: Disable TSX development mode at boot
+    - genirq/affinity: Consider that CPUs on nodes can be unbalanced
+    - tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
+    - ARM: davinci: da850-evm: Avoid NULL pointer dereference
+    - dm integrity: fix memory corruption when tag_size is less than digest size
+    - i2c: dev: check return value when calling dev_set_name()
+    - smp: Fix offline cpu check in flush_smp_call_function_queue()
+    - i2c: pasemi: Wait for write xfers to finish
+    - dt-bindings: net: snps: remove duplicate name
+    - timers: Fix warning condition in __run_timers()
+    - dma-direct: avoid redundant memory sync for swiotlb
+    - drm/i915: Sunset igpu legacy mmap support based on GRAPHICS_VER_FULL
+    - cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
+    - soc: qcom: aoss: Fix missing put_device call in qmp_get
+    - net: ipa: fix a build dependency
+    - cpufreq: intel_pstate: ITMT support for overclocked system
+    - ax25: add refcount in ax25_dev to avoid UAF bugs
+    - ax25: fix reference count leaks of ax25_dev
+    - ax25: fix UAF bugs of net_device caused by rebinding operation
+    - ax25: Fix refcount leaks caused by ax25_cb_del()
+    - ax25: fix UAF bug in ax25_send_control()
+    - ax25: fix NPD bug in ax25_disconnect
+    - ax25: Fix NULL pointer dereferences in ax25 timers
+    - ax25: Fix UAF bugs in ax25 timers
+    - Linux 5.15.35
+  * CONFIG_SND_COMPRESS_OFFLOAD missing in jammy/ppc64el kernel config
+    (LP: #1969807)
+    - [Config] updateconfigs for SND_COMPRESS_OFFLOAD (ppc64el)
+  * Micmute LED support for Zbook Fury 16 G9 (LP: #1968892)
+    - ALSA: hda/realtek: Add mute and micmut LED support for Zbook Fury 17 G9
+  * Fix broken HDMI audio on AMD PRO VII after S3 (LP: #1968475)
+    - drm/amdgpu: don't set s3 and s0ix at the same time
+    - drm/amdgpu: Ensure HDA function is suspended before ASIC reset
+  * [Ubuntu 22.04] mpi3mr: Request to include latest bug fixes (LP: #1967116)
+    - scsi: mpi3mr: Clean up mpi3mr_print_ioc_info()
+    - scsi: mpi3mr: Use scnprintf() instead of snprintf()
+    - scsi: mpi3mr: Add debug APIs based on logging_level bits
+    - scsi: mpi3mr: Replace spin_lock() with spin_lock_irqsave()
+    - scsi: mpi3mr: Don't reset IOC if cmnds flush with reset status
+    - scsi: mpi3mr: Update MPI3 headers - part1
+    - scsi: mpi3mr: Update MPI3 headers - part2
+    - scsi: mpi3mr: Add support for PCIe Managed Switch SES device
+    - scsi: mpi3mr: Do access status validation before adding devices
+    - scsi: mpi3mr: Increase internal cmnds timeout to 60s
+    - scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
+    - scsi: mpi3mr: Display IOC firmware package version
+    - scsi: mpi3mr: Fault IOC when internal command gets timeout
+    - scsi: mpi3mr: Code refactor of IOC init - part1
+    - scsi: mpi3mr: Code refactor of IOC init - part2
+    - scsi: mpi3mr: Handle offline FW activation in graceful manner
+    - scsi: mpi3mr: Add IOC reinit function
+    - scsi: mpi3mr: Detect async reset that occurred in firmware
+    - scsi: mpi3mr: Gracefully handle online FW update operation
+    - scsi: mpi3mr: Add Event acknowledgment logic
+    - scsi: mpi3mr: Support Prepare for Reset event
+    - scsi: mpi3mr: Print cable mngnt and temp threshold events
+    - scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
+    - scsi: mpi3mr: Use TM response codes from MPI3 headers
+    - scsi: mpi3mr: Enhanced Task Management Support Reply handling
+    - scsi: mpi3mr: Bump driver version to 8.0.0.61.0
+    - scsi: mpi3mr: Fix some spelling mistakes
+    - scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
+    - scsi: mpi3mr: Fix deadlock while canceling the fw event
+    - scsi: mpi3mr: Fix printing of pending I/O count
+    - scsi: mpi3mr: Update MPI3 headers
+    - scsi: mpi3mr: Fix hibernation issue
+    - scsi: mpi3mr: Fix cmnd getting marked as in use forever
+    - scsi: mpi3mr: Update the copyright year
+    - scsi: mpi3mr: Bump driver version to 8.0.0.68.0
+    - scsi: mpi3mr: Fix flushing !WQ_MEM_RECLAIM events warning
+  * Support AMD P-State cpufreq control mechanism (LP: #1956509)
+    - x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature
+      flag
+    - x86/msr: Add AMD CPPC MSR definitions
+    - ACPI: CPPC: Implement support for SystemIO registers
+    - ACPI: CPPC: Add CPPC enable register function
+    - cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future
+      processors
+    - cpufreq: amd-pstate: Add fast switch function for AMD P-State
+    - cpufreq: amd-pstate: Introduce the support for the processors with shared
+      memory solution
+    - cpufreq: amd-pstate: Add trace for AMD P-State module
+    - cpufreq: amd-pstate: Add boost mode support for AMD P-State
+    - cpufreq: amd-pstate: Add AMD P-State frequencies attributes
+    - cpufreq: amd-pstate: Add AMD P-State performance attributes
+    - Documentation: amd-pstate: Add AMD P-State driver introduction
+    - MAINTAINERS: Add AMD P-State driver maintainer entry
+    - cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
+    - cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
+    - [Config] enable X86_AMD_PSTATE as built-in on amd64
+  * Bolt doesn't work with native USB4 hosts (LP: #1962349)
+    - thunderbolt: Retry DROM reads for more failure scenarios
+    - thunderbolt: Do not resume routers if UID is not set
+    - thunderbolt: Do not make DROM read success compulsory
+    - PCI/ACPI: Allow D3 only if Root Port can signal and wake from D3
+  * linux-image-5.0.0-35-generic breaks checkpointing of container
+    (LP: #1857257) // re-apply missing overlayfs SAUCE patch (LP: #1967924)
+    - SAUCE: overlayfs: fix incorrect mnt_id of files opened from map_files
+  * [Jammy, mlx5, ConnectX-7] add CX7 support for software steering
+    (LP: #1966194)
+    - net/mlx5: DR, Fix vport number data type to u16
+    - net/mlx5: DR, Replace local WIRE_PORT macro with the existing
+      MLX5_VPORT_UPLINK
+    - net/mlx5: DR, Add missing query for vport 0
+    - net/mlx5: DR, Align error messages for failure to obtain vport caps
+    - net/mlx5: DR, Support csum recalculation flow table on SFs
+    - net/mlx5: DR, Add support for SF vports
+    - net/mlx5: DR, Increase supported num of actions to 32
+    - net/mlx5: DR, Fix typo 'offeset' to 'offset'
+    - net/mlx5: DR, init_next_match only if needed
+    - net/mlx5: DR, Add missing string for action type SAMPLER
+    - net/mlx5: DR, Add check for unsupported fields in match param
+    - net/mlx5: Introduce new uplink destination type
+    - net/mlx5: DR, Handle eswitch manager and uplink vports separately
+    - net/mlx5: DR, Fix querying eswitch manager vport for ECPF
+    - net/mlx5: DR, Fix check for unsupported fields in match param
+    - net/mlx5: DR, Fix error flow in creating matcher
+    - net/mlx5: DR, Fix lower case macro prefix "mlx5_" to "MLX5_"
+    - net/mlx5: DR, Remove unused struct member in matcher
+    - net/mlx5: DR, Rename list field in matcher struct to list_node
+    - net/mlx5: DR, Add check for flex parser ID value
+    - net/mlx5: DR, Add missing reserved fields to dr_match_param
+    - net/mlx5: DR, Add support for dumping steering info
+    - net/mlx5: DR, Add support for UPLINK destination type
+    - net/mlx5: DR, Warn on failure to destroy objects due to refcount
+    - net/mlx5: Add misc5 flow table match parameters
+    - net/mlx5: DR, Add misc5 to match_param structs
+    - net/mlx5: DR, Support matching on tunnel headers 0 and 1
+    - net/mlx5: DR, Add support for matching on geneve_tlv_option_0_exist field
+    - net/mlx5: DR, Improve steering for empty or RX/TX-only matchers
+    - net/mlx5: DR, Ignore modify TTL if device doesn't support it
+    - net/mlx5: Set SMFS as a default steering mode if device supports it
+    - net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
+    - net/mlx5: DR, Add support for matching on Internet Header Length (IHL)
+    - net/mlx5: DR, Remove unneeded comments
+    - net/mlx5: DR, Fix handling of different actions on the same STE in STEv1
+    - net/mlx5: DR, Rename action modify fields to reflect naming in HW spec
+    - net/mlx5: DR, Refactor ste_ctx handling for STE v0/1
+    - net/mlx5: Introduce software defined steering capabilities
+    - net/mlx5: DR, Add support for ConnectX-7 steering
+  * alsa: enable the cirrus-logic side-codec to make the speaker output sound
+    (LP: #1965496)
+    - ASoC: cs35l41: CS35L41 Boosted Smart Amplifier
+    - ASoC: cs35l41: Fix use of an uninitialised variable
+    - ASoC: cs35l41: Use regmap_read_poll_timeout to wait for OTP boot
+    - ASoC: cs35l41: Combine adjacent register writes
+    - ASoC: cs35l41: Don't overwrite returned error code
+    - ASoC: cs35l41: Fixup the error messages
+    - ASoC: cs35l41: Fix a bunch of trivial code formating/style issues
+    - misc: cs35l41: Remove unused pdn variable
+    - ASoC: cs35l41: Make cs35l41_remove() return void
+    - ASoC: cs35l41: Change monitor widgets to siggens
+    - ASoC: cs35l41: DSP Support
+    - ASoC: cs35l41: Set the max SPI speed for the whole device
+    - ASoC: cs35l41: Fix link problem
+    - ASoC: cs35l41: Fix undefined reference to core functions
+    - ASoC: cs35l41: Convert tables to shared source code
+    - ASoC: cs35l41: Move cs35l41_otp_unpack to shared code
+    - ASoC: cs35l41: Move power initializations to reg_sequence
+    - ASoC: cs35l41: Create shared function for errata patches
+    - ASoC: cs35l41: Create shared function for setting channels
+    - ASoC: cs35l41: Create shared function for boost configuration
+    - ASoC: cs35l41: Add cs35l51/53 IDs
+    - ASoC: cs35l41: Remove incorrect comment
+    - ASoC: cs35l41: Correct DSP power down
+    - ASoC: cs35l41: Correct handling of some registers in the cache
+    - ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems
+    - ASoC: cs35l41: Update handling of test key registers
+    - ASoC: cs35l41: Add support for hibernate memory retention mode
+    - ALSA: hda: cs35l41: fix double free on error in probe()
+    - ALSA: hda: cs35l41: Avoid overwriting register patch
+    - ALSA: hda: cs35l41: Add calls to newly added test key function
+    - ALSA: hda: cs35l41: Move cs35l41* calls to its own symbol namespace
+    - ALSA: hda: cs35l41: Add missing default cases
+    - ALSA: hda: cs35l41: Make use of the helper function dev_err_probe()
+    - ALSA: hda: cs35l41: Tidyup code
+    - ALSA: hda: cs35l41: Make cs35l41_hda_remove() return void
+    - ALSA: hda/realtek: Add support for Legion 7 16ACHg6 laptop
+    - ALSA: hda/realtek: Add CS35L41 support for Thinkpad laptops
+    - ALSA: hda/realtek: fix speakers and micmute on HP 855 G8
+    - Revert "platform/x86: i2c-multi-instantiate: Don't create platform device
+      for INT3515 ACPI nodes"
+    - spi: Create helper API to lookup ACPI info for spi device
+    - spi: Support selection of the index of the ACPI Spi Resource before alloc
+    - spi: Add API to count spi acpi resources
+    - platform/x86: i2c-multi-instantiate: Rename it for a generic serial driver
+      name
+    - platform/x86: serial-multi-instantiate: Reorganize I2C functions
+    - platform/x86: serial-multi-instantiate: Add SPI support
+    - ALSA: hda/realtek: Add support for HP Laptops
+    - ACPI / scan: Create platform device for CS35L41
+    - [Config] Add cirruslogic side codec support
+  * Use kernel-testing repo from launchpad for ADT tests (LP: #1968016)
+    - [Debian] Use kernel-testing repo from launchpad
+  * Fix ADL, WD22TB4,Dual monitors display resolution can't reach 4K 60hz
+    (LP: #1967986)
+    - drm/i915/display: Remove check for low voltage sku for max dp source rate
+    - drm/i915/intel_combo_phy: Print I/O voltage info
+  * Support different Cirrus audio codec configurations on Dell laptops
+    (LP: #1967988)
+    - ALSA: hda/cs8409: Fix Warlock to use mono mic configuration
+    - ALSA: hda/cs8409: Re-order quirk table into ascending order
+    - ALSA: hda/cs8409: Fix Full Scale Volume setting for all variants
+    - ALSA: hda/cs8409: Support new Warlock MLK Variants
+    - ALSA: hda/cs8409: Disable HSBIAS_SENSE_EN for Cyborg
+    - ALSA: hda/cs8409: Add new Dolphin HW variants
+  * Enable speakup kernel modules to allow the speakup screen reader to function
+    (LP: #1967702)
+    - [Config] CONFIG_SPEAKUP=m
+  * linux: CONFIG_SERIAL_8250_MID=y (LP: #1967338)
+    - [Config] amd64 CONFIG_SERIAL_8250_MID=y
+  * alsa/sdw: Fix the audio issue on a Dell machine without internal mic
+    (LP: #1966841)
+    - ASoC: Intel: soc-acpi: add entries in ADL match table
+  * Jammy update: v5.15.34 upstream stable release (LP: #1969107)
+    - Revert "UBUNTU: SAUCE: Revert "scsi: core: Reallocate device's budget map on
+      queue depth change""
+    - lib/logic_iomem: correct fallback config references
+    - um: fix and optimize xor select template for CONFIG64 and timetravel mode
+    - rtc: wm8350: Handle error for wm8350_register_irq
+    - nbd: add error handling support for add_disk()
+    - nbd: Fix incorrect error handle when first_minor is illegal in nbd_dev_add
+    - nbd: Fix hungtask when nbd_config_put
+    - nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
+    - kfence: count unexpectedly skipped allocations
+    - kfence: move saving stack trace of allocations into __kfence_alloc()
+    - kfence: limit currently covered allocations when pool nearly full
+    - KVM: x86/pmu: Use different raw event masks for AMD and Intel
+    - KVM: SVM: Fix kvm_cache_regs.h inclusions for is_guest_mode()
+    - KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
+    - KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
+    - KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
+    - drm: Add orientation quirk for GPD Win Max
+    - ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111
+    - drm/amd/display: Add signal type check when verify stream backends same
+    - drm/amd/amdgpu/amdgpu_cs: fix refcount leak of a dma_fence obj
+    - drm/amd/display: Fix memory leak
+    - drm/amd/display: Use PSR version selected during set_psr_caps
+    - usb: gadget: tegra-xudc: Do not program SPARAM
+    - usb: gadget: tegra-xudc: Fix control endpoint's definitions
+    - usb: cdnsp: fix cdnsp_decode_trb function to properly handle ret value
+    - ptp: replace snprintf with sysfs_emit
+    - drm/amdkfd: Don't take process mutex for svm ioctls
+    - powerpc: dts: t104xrdb: fix phy type for FMAN 4/5
+    - ath11k: fix kernel panic during unload/load ath11k modules
+    - ath11k: pci: fix crash on suspend if board file is not found
+    - ath11k: mhi: use mhi_sync_power_up()
+    - net/smc: Send directly when TCP_CORK is cleared
+    - drm/bridge: Add missing pm_runtime_put_sync
+    - bpf: Make dst_port field in struct bpf_sock 16-bit wide
+    - scsi: mvsas: Replace snprintf() with sysfs_emit()
+    - scsi: bfa: Replace snprintf() with sysfs_emit()
+    - drm/v3d: fix missing unlock
+    - power: supply: axp20x_battery: properly report current when discharging
+    - mt76: mt7921: fix crash when startup fails.
+    - mt76: dma: initialize skip_unmap in mt76_dma_rx_fill
+    - cfg80211: don't add non transmitted BSS to 6GHz scanned channels
+    - libbpf: Fix build issue with llvm-readelf
+    - ipv6: make mc_forwarding atomic
+    - net: initialize init_net earlier
+    - powerpc: Set crashkernel offset to mid of RMA region
+    - drm/amdgpu: Fix recursive locking warning
+    - scsi: smartpqi: Fix kdump issue when controller is locked up
+    - PCI: aardvark: Fix support for MSI interrupts
+    - iommu/arm-smmu-v3: fix event handling soft lockup
+    - usb: ehci: add pci device support for Aspeed platforms
+    - PCI: endpoint: Fix alignment fault error in copy tests
+    - tcp: Don't acquire inet_listen_hashbucket::lock with disabled BH.
+    - PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
+    - scsi: mpi3mr: Fix reporting of actual data transfer size
+    - scsi: mpi3mr: Fix memory leaks
+    - powerpc/set_memory: Avoid spinlock recursion in change_page_attr()
+    - power: supply: axp288-charger: Set Vhold to 4.4V
+    - net/mlx5e: Disable TX queues before registering the netdev
+    - usb: dwc3: pci: Set the swnode from inside dwc3_pci_quirks()
+    - iwlwifi: mvm: Correctly set fragmented EBS
+    - iwlwifi: mvm: move only to an enabled channel
+    - drm/msm/dsi: Remove spurious IRQF_ONESHOT flag
+    - ipv4: Invalidate neighbour for broadcast address upon address addition
+    - dm ioctl: prevent potential spectre v1 gadget
+    - dm: requeue IO if mapping table not yet available
+    - drm/amdkfd: make CRAT table missing message informational only
+    - vfio/pci: Stub vfio_pci_vga_rw when !CONFIG_VFIO_PCI_VGA
+    - scsi: pm8001: Fix pm80xx_pci_mem_copy() interface
+    - scsi: pm8001: Fix pm8001_mpi_task_abort_resp()
+    - scsi: pm8001: Fix task leak in pm8001_send_abort_all()
+    - scsi: pm8001: Fix tag leaks on error
+    - scsi: pm8001: Fix memory leak in pm8001_chip_fw_flash_update_req()
+    - mt76: mt7915: fix injected MPDU transmission to not use HW A-MSDU
+    - powerpc/64s/hash: Make hash faults work in NMI context
+    - mt76: mt7615: Fix assigning negative values to unsigned variable
+    - scsi: aha152x: Fix aha152x_setup() __setup handler return value
+    - scsi: hisi_sas: Free irq vectors in order for v3 HW
+    - scsi: hisi_sas: Limit users changing debugfs BIST count value
+    - net/smc: correct settings of RMB window update limit
+    - mips: ralink: fix a refcount leak in ill_acc_of_setup()
+    - macvtap: advertise link netns via netlink
+    - tuntap: add sanity checks about msg_controllen in sendmsg
+    - Bluetooth: Fix not checking for valid hdev on bt_dev_{info,warn,err,dbg}
+    - Bluetooth: use memset avoid memory leaks
+    - bnxt_en: Eliminate unintended link toggle during FW reset
+    - PCI: endpoint: Fix misused goto label
+    - MIPS: fix fortify panic when copying asm exception handlers
+    - powerpc/64e: Tie PPC_BOOK3E_64 to PPC_FSL_BOOK3E
+    - powerpc/secvar: fix refcount leak in format_show()
+    - scsi: libfc: Fix use after free in fc_exch_abts_resp()
+    - can: isotp: set default value for N_As to 50 micro seconds
+    - can: etas_es58x: es58x_fd_rx_event_msg(): initialize rx_event_msg before
+      calling es58x_check_msg_len()
+    - riscv: Fixed misaligned memory access. Fixed pointer comparison.
+    - net: account alternate interface name memory
+    - net: limit altnames to 64k total
+    - net/mlx5e: Remove overzealous validations in netlink EEPROM query
+    - net: sfp: add 2500base-X quirk for Lantech SFP module
+    - usb: dwc3: omap: fix "unbalanced disables for smps10_out1" on omap5evm
+    - mt76: fix monitor mode crash with sdio driver
+    - xtensa: fix DTC warning unit_address_format
+    - MIPS: ingenic: correct unit node address
+    - Bluetooth: Fix use after free in hci_send_acl
+    - netfilter: conntrack: revisit gc autotuning
+    - netlabel: fix out-of-bounds memory accesses
+    - ceph: fix inode reference leakage in ceph_get_snapdir()
+    - ceph: fix memory leak in ceph_readdir when note_last_dentry returns error
+    - lib/Kconfig.debug: add ARCH dependency for FUNCTION_ALIGN option
+    - init/main.c: return 1 from handled __setup() functions
+    - minix: fix bug when opening a file with O_DIRECT
+    - clk: si5341: fix reported clk_rate when output divider is 2
+    - staging: vchiq_arm: Avoid NULL ptr deref in vchiq_dump_platform_instances
+    - staging: vchiq_core: handle NULL result of find_service_by_handle
+    - phy: amlogic: phy-meson-gxl-usb2: fix shared reset controller use
+    - phy: amlogic: meson8b-usb2: Use dev_err_probe()
+    - phy: amlogic: meson8b-usb2: fix shared reset control use
+    - clk: rockchip: drop CLK_SET_RATE_PARENT from dclk_vop* on rk3568
+    - cpufreq: CPPC: Fix performance/frequency conversion
+    - opp: Expose of-node's name in debugfs
+    - staging: wfx: fix an error handling in wfx_init_common()
+    - w1: w1_therm: fixes w1_seq for ds28ea00 sensors
+    - NFSv4.2: fix reference count leaks in _nfs42_proc_copy_notify()
+    - NFSv4: Protect the state recovery thread against direct reclaim
+    - habanalabs: fix possible memory leak in MMU DR fini
+    - xen: delay xen_hvm_init_time_ops() if kdump is boot on vcpu>=32
+    - clk: ti: Preserve node in ti_dt_clocks_register()
+    - clk: Enforce that disjoints limits are invalid
+    - SUNRPC/call_alloc: async tasks mustn't block waiting for memory
+    - SUNRPC/xprt: async tasks mustn't block waiting for memory
+    - SUNRPC: remove scheduling boost for "SWAPPER" tasks.
+    - NFS: swap IO handling is slightly different for O_DIRECT IO
+    - NFS: swap-out must always use STABLE writes.
+    - x86: Annotate call_on_stack()
+    - x86/Kconfig: Do not allow CONFIG_X86_X32_ABI=y with llvm-objcopy
+    - serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
+    - virtio_console: eliminate anonymous module_init & module_exit
+    - jfs: prevent NULL deref in diFree
+    - SUNRPC: Fix socket waits for write buffer space
+    - NFS: nfsiod should not block forever in mempool_alloc()
+    - NFS: Avoid writeback threads getting stuck in mempool_alloc()
+    - selftests: net: Add tls config dependency for tls selftests
+    - parisc: Fix CPU affinity for Lasi, WAX and Dino chips
+    - parisc: Fix patch code locking and flushing
+    - mm: fix race between MADV_FREE reclaim and blkdev direct IO read
+    - rtc: mc146818-lib: change return values of mc146818_get_time()
+    - rtc: Check return value from mc146818_get_time()
+    - rtc: mc146818-lib: fix RTC presence check
+    - drm/amdgpu: fix off by one in amdgpu_gfx_kiq_acquire()
+    - Drivers: hv: vmbus: Fix potential crash on module unload
+    - Revert "NFSv4: Handle the special Linux file open access mode"
+    - NFSv4: fix open failure with O_ACCMODE flag
+    - scsi: sr: Fix typo in CDROM(CLOSETRAY|EJECT) handling
+    - scsi: core: Fix sbitmap depth in scsi_realloc_sdev_budget_map()
+    - scsi: zorro7xx: Fix a resource leak in zorro7xx_remove_one()
+    - vdpa/mlx5: Rename control VQ workqueue to vdpa wq
+    - vdpa/mlx5: Propagate link status from device to vdpa driver
+    - vdpa: mlx5: prevent cvq work from hogging CPU
+    - net: sfc: add missing xdp queue reinitialization
+    - net/tls: fix slab-out-of-bounds bug in decrypt_internal
+    - vrf: fix packet sniffing for traffic originating from ip tunnels
+    - skbuff: fix coalescing for page_pool fragment recycling
+    - ice: Clear default forwarding VSI during VSI release
+    - mctp: Fix check for dev_hard_header() result
+    - net: ipv4: fix route with nexthop object delete warning
+    - net: stmmac: Fix unset max_speed difference between DT and non-DT platforms
+    - drm/imx: imx-ldb: Check for null pointer after calling kmemdup
+    - drm/imx: Fix memory leak in imx_pd_connector_get_modes
+    - drm/imx: dw_hdmi-imx: Fix bailout in error cases of probe
+    - regulator: rtq2134: Fix missing active_discharge_on setting
+    - regulator: atc260x: Fix missing active_discharge_on setting
+    - arch/arm64: Fix topology initialization for core scheduling
+    - bnxt_en: Synchronize tx when xdp redirects happen on same ring
+    - bnxt_en: reserve space inside receive page for skb_shared_info
+    - bnxt_en: Prevent XDP redirect from running when stopping TX queue
+    - sfc: Do not free an empty page_ring
+    - RDMA/mlx5: Don't remove cache MRs when a delay is needed
+    - RDMA/mlx5: Add a missing update of cache->last_add
+    - IB/cm: Cancel mad on the DREQ event when the state is MRA_REP_RCVD
+    - IB/rdmavt: add lock to call to rvt_error_qp to prevent a race condition
+    - sctp: count singleton chunks in assoc user stats
+    - dpaa2-ptp: Fix refcount leak in dpaa2_ptp_probe
+    - ice: Set txq_teid to ICE_INVAL_TEID on ring creation
+    - ice: Do not skip not enabled queues in ice_vc_dis_qs_msg
+    - ipv6: Fix stats accounting in ip6_pkt_drop
+    - ice: synchronize_rcu() when terminating rings
+    - ice: xsk: fix VSI state check in ice_xsk_wakeup()
+    - net: openvswitch: don't send internal clone attribute to the userspace.
+    - net: ethernet: mv643xx: Fix over zealous checking of_get_mac_address()
+    - net: openvswitch: fix leak of nested actions
+    - rxrpc: fix a race in rxrpc_exit_net()
+    - net: sfc: fix using uninitialized xdp tx_queue
+    - net: phy: mscc-miim: reject clause 45 register accesses
+    - qede: confirm skb is allocated before using
+    - spi: bcm-qspi: fix MSPI only access with bcm_qspi_exec_mem_op()
+    - bpf: Support dual-stack sockets in bpf_tcp_check_syncookie
+    - drbd: Fix five use after free bugs in get_initial_state
+    - scsi: ufs: ufshpb: Fix a NULL check on list iterator
+    - io_uring: nospec index for tags on files update
+    - io_uring: don't touch scm_fp_list after queueing skb
+    - SUNRPC: Handle ENOMEM in call_transmit_status()
+    - SUNRPC: Handle low memory situations in call_status()
+    - SUNRPC: svc_tcp_sendmsg() should handle errors from xdr_alloc_bvec()
+    - iommu/omap: Fix regression in probe for NULL pointer dereference
+    - perf: arm-spe: Fix perf report --mem-mode
+    - perf tools: Fix perf's libperf_print callback
+    - perf session: Remap buf if there is no space for event
+    - arm64: Add part number for Arm Cortex-A78AE
+    - scsi: mpt3sas: Fix use after free in _scsih_expander_node_remove()
+    - scsi: ufs: ufs-pci: Add support for Intel MTL
+    - Revert "mmc: sdhci-xenon: fix annoying 1.8V regulator warning"
+    - mmc: block: Check for errors after write on SPI
+    - mmc: mmci: stm32: correctly check all elements of sg list
+    - mmc: renesas_sdhi: don't overwrite TAP settings when HS400 tuning is
+      complete
+    - mmc: core: Fixup support for writeback-cache for eMMC and SD
+    - lz4: fix LZ4_decompress_safe_partial read out of bound
+    - highmem: fix checks in __kmap_local_sched_{in,out}
+    - mmmremap.c: avoid pointless invalidate_range_start/end on mremap(old_size=0)
+    - mm/mempolicy: fix mpol_new leak in shared_policy_replace
+    - io_uring: don't check req->file in io_fsync_prep()
+    - io_uring: defer splice/tee file validity check until command issue
+    - io_uring: implement compat handling for IORING_REGISTER_IOWQ_AFF
+    - io_uring: fix race between timeout flush and removal
+    - x86/pm: Save the MSR validity status at context setup
+    - x86/speculation: Restore speculation related MSRs during S3 resume
+    - perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
+    - btrfs: fix qgroup reserve overflow the qgroup limit
+    - btrfs: prevent subvol with swapfile from being deleted
+    - spi: core: add dma_map_dev for __spi_unmap_msg()
+    - arm64: patch_text: Fixup last cpu should be master
+    - RDMA/hfi1: Fix use-after-free bug for mm struct
+    - gpio: Restrict usage of GPIO chip irq members before initialization
+    - x86/msi: Fix msi message data shadow struct
+    - x86/mm/tlb: Revert retpoline avoidance approach
+    - perf/x86/intel: Don't extend the pseudo-encoding to GP counters
+    - ata: sata_dwc_460ex: Fix crash due to OOB write
+    - perf: qcom_l2_pmu: fix an incorrect NULL check on list iterator
+    - perf/core: Inherit event_caps
+    - irqchip/gic-v3: Fix GICR_CTLR.RWP polling
+    - fbdev: Fix unregistering of framebuffers without device
+    - amd/display: set backlight only if required
+    - SUNRPC: Prevent immediate close+reconnect
+    - drm/panel: ili9341: fix optional regulator handling
+    - drm/amdgpu/display: change pipe policy for DCN 2.1
+    - drm/amdgpu/smu10: fix SoC/fclk units in auto mode
+    - drm/amdgpu/vcn: Fix the register setting for vcn1
+    - drm/nouveau/pmu: Add missing callbacks for Tegra devices
+    - drm/amdkfd: Create file descriptor after client is added to smi_clients list
+    - drm/amdgpu: don't use BACO for reset in S3
+    - KVM: SVM: Allow AVIC support on system w/ physical APIC ID > 255
+    - net/smc: send directly on setting TCP_NODELAY
+    - Revert "selftests: net: Add tls config dependency for tls selftests"
+    - bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
+    - selftests/bpf: Fix u8 narrow load checks for bpf_sk_lookup remote_port
+    - rtc: mc146818-lib: fix signedness bug in mc146818_get_time()
+    - SUNRPC: Don't call connect() more than once on a TCP socket
+    - Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"
+    - perf build: Don't use -ffat-lto-objects in the python feature test when
+      building with clang-13
+    - perf python: Fix probing for some clang command line options
+    - tools build: Filter out options and warnings not supported by clang
+    - tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
+    - dmaengine: Revert "dmaengine: shdma: Fix runtime PM imbalance on error"
+    - KVM: avoid NULL pointer dereference in kvm_dirty_ring_push
+    - Revert "net/mlx5: Accept devlink user input after driver initialization
+      complete"
+    - ubsan: remove CONFIG_UBSAN_OBJECT_SIZE
+    - selftests: cgroup: Make cg_create() use 0755 for permission instead of 0644
+    - selftests: cgroup: Test open-time credential usage for migration checks
+    - selftests: cgroup: Test open-time cgroup namespace usage for migration
+      checks
+    - mm: don't skip swap entry even if zap_details specified
+    - Drivers: hv: vmbus: Replace smp_store_mb() with virt_store_mb()
+    - x86/bug: Prevent shadowing in __WARN_FLAGS
+    - sched: Teach the forced-newidle balancer about CPU affinity limitation.
+    - x86,static_call: Fix __static_call_return0 for i386
+    - irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
+    - powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
+    - irqchip/gic, gic-v3: Prevent GSI to SGI translations
+    - mm/sparsemem: fix 'mem_section' will never be NULL gcc 12 warning
+    - static_call: Don't make __static_call_return0 static
+    - powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
+    - stacktrace: move filter_irq_stacks() to kernel/stacktrace.c
+    - Linux 5.15.34
+    - [Config] armhf, s390x: update annotations following
+      DEBUG_FORCE_FUNCTION_ALIGN_64B support removal in v5.15.34
+  * Jammy update: v5.15.33 upstream stable release (LP: #1969110)
+    - Revert "swiotlb: rework "fix info leak with DMA_FROM_DEVICE""
+    - USB: serial: pl2303: add IBM device IDs
+    - dt-bindings: usb: hcd: correct usb-device path
+    - USB: serial: pl2303: fix GS type detection
+    - USB: serial: simple: add Nokia phone driver
+    - mm: kfence: fix missing objcg housekeeping for SLAB
+    - hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
+    - HID: logitech-dj: add new lightspeed receiver id
+    - HID: Add support for open wheel and no attachment to T300
+    - xfrm: fix tunnel model fragmentation behavior
+    - ARM: mstar: Select HAVE_ARM_ARCH_TIMER
+    - virtio_console: break out of buf poll on remove
+    - vdpa/mlx5: should verify CTRL_VQ feature exists for MQ
+    - tools/virtio: fix virtio_test execution
+    - ethernet: sun: Free the coherent when failing in probing
+    - gpio: Revert regression in sysfs-gpio (gpiolib.c)
+    - spi: Fix invalid sgs value
+    - net:mcf8390: Use platform_get_irq() to get the interrupt
+    - Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"
+    - spi: Fix erroneous sgs value with min_t()
+    - Input: zinitix - do not report shadow fingers
+    - af_key: add __GFP_ZERO flag for compose_sadb_supported in function
+      pfkey_register
+    - net: dsa: microchip: add spi_device_id tables
+    - selftests: vm: fix clang build error multiple output files
+    - locking/lockdep: Avoid potential access of invalid memory in lock_class
+    - drm/amdgpu: move PX checking into amdgpu_device_ip_early_init
+    - drm/amdgpu: only check for _PR3 on dGPUs
+    - iommu/iova: Improve 32-bit free space estimate
+    - virtio-blk: Use blk_validate_block_size() to validate block size
+    - tpm: fix reference counting for struct tpm_chip
+    - usb: typec: tipd: Forward plug orientation to typec subsystem
+    - USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
+    - xhci: fix garbage USBSTS being logged in some cases
+    - xhci: fix runtime PM imbalance in USB2 resume
+    - xhci: make xhci_handshake timeout for xhci_reset() adjustable
+    - xhci: fix uninitialized string returned by xhci_decode_ctrl_ctx()
+    - mei: me: disable driver on the ign firmware
+    - mei: me: add Alder Lake N device id.
+    - mei: avoid iterator usage outside of list_for_each_entry
+    - bus: mhi: pci_generic: Add mru_default for Quectel EM1xx series
+    - bus: mhi: Fix MHI DMA structure endianness
+    - docs: sphinx/requirements: Limit jinja2<3.1
+    - coresight: Fix TRCCONFIGR.QE sysfs interface
+    - coresight: syscfg: Fix memleak on registration failure in
+      cscfg_create_device
+    - iio: afe: rescale: use s64 for temporary scale calculations
+    - iio: inkern: apply consumer scale on IIO_VAL_INT cases
+    - iio: inkern: apply consumer scale when no channel scale is available
+    - iio: inkern: make a best effort on offset calculation
+    - greybus: svc: fix an error handling bug in gb_svc_hello()
+    - clk: rockchip: re-add rational best approximation algorithm to the
+      fractional divider
+    - clk: uniphier: Fix fixed-rate initialization
+    - cifs: fix handlecache and multiuser
+    - cifs: we do not need a spinlock around the tree access during umount
+    - KEYS: fix length validation in keyctl_pkey_params_get_2()
+    - KEYS: asymmetric: enforce that sig algo matches key algo
+    - KEYS: asymmetric: properly validate hash_algo and encoding
+    - Documentation: add link to stable release candidate tree
+    - Documentation: update stable tree link
+    - firmware: stratix10-svc: add missing callback parameter on RSU
+    - firmware: sysfb: fix platform-device leak in error path
+    - HID: intel-ish-hid: Use dma_alloc_coherent for firmware update
+    - SUNRPC: avoid race between mod_timer() and del_timer_sync()
+    - NFS: NFSv2/v3 clients should never be setting NFS_CAP_XATTR
+    - NFSD: prevent underflow in nfssvc_decode_writeargs()
+    - NFSD: prevent integer overflow on 32 bit systems
+    - f2fs: fix to unlock page correctly in error path of is_alive()
+    - f2fs: quota: fix loop condition at f2fs_quota_sync()
+    - f2fs: fix to do sanity check on .cp_pack_total_block_count
+    - remoteproc: Fix count check in rproc_coredump_write()
+    - mm/mlock: fix two bugs in user_shm_lock()
+    - pinctrl: ingenic: Fix regmap on X series SoCs
+    - pinctrl: samsung: drop pin banks references on error paths
+    - net: bnxt_ptp: fix compilation error
+    - spi: mxic: Fix the transmit path
+    - mtd: rawnand: protect access to rawnand devices while in suspend
+    - can: ems_usb: ems_usb_start_xmit(): fix double dev_kfree_skb() in error path
+    - can: m_can: m_can_tx_handler(): fix use after free of skb
+    - can: usb_8dev: usb_8dev_start_xmit(): fix double dev_kfree_skb() in error
+      path
+    - jffs2: fix use-after-free in jffs2_clear_xattr_subsystem
+    - jffs2: fix memory leak in jffs2_do_mount_fs
+    - jffs2: fix memory leak in jffs2_scan_medium
+    - mm: fs: fix lru_cache_disabled race in bh_lru
+    - mm/pages_alloc.c: don't create ZONE_MOVABLE beyond the end of a node
+    - mm: invalidate hwpoison page cache page in fault path
+    - mempolicy: mbind_range() set_policy() after vma_merge()
+    - scsi: core: sd: Add silence_suspend flag to suppress some PM messages
+    - scsi: ufs: Fix runtime PM messages never-ending cycle
+    - scsi: scsi_transport_fc: Fix FPIN Link Integrity statistics counters
+    - scsi: libsas: Fix sas_ata_qc_issue() handling of NCQ NON DATA commands
+    - qed: display VF trust config
+    - qed: validate and restrict untrusted VFs vlan promisc mode
+    - riscv: dts: canaan: Fix SPI3 bus width
+    - riscv: Fix fill_callchain return value
+    - riscv: Increase stack size under KASAN
+    - Revert "Input: clear BTN_RIGHT/MIDDLE on buttonpads"
+    - cifs: prevent bad output lengths in smb2_ioctl_query_info()
+    - cifs: fix NULL ptr dereference in smb2_ioctl_query_info()
+    - ALSA: cs4236: fix an incorrect NULL check on list iterator
+    - ALSA: hda: Avoid unsol event during RPM suspending
+    - ALSA: pcm: Fix potential AB/BA lock with buffer_mutex and mmap_lock
+    - ALSA: hda/realtek: Fix audio regression on Mi Notebook Pro 2020
+    - rtc: mc146818-lib: fix locking in mc146818_set_time
+    - rtc: pl031: fix rtc features null pointer dereference
+    - ocfs2: fix crash when mount with quota enabled
+    - drm/simpledrm: Add "panel orientation" property on non-upright mounted LCD
+      panels
+    - mm: madvise: skip unmapped vma holes passed to process_madvise
+    - mm: madvise: return correct bytes advised with process_madvise
+    - Revert "mm: madvise: skip unmapped vma holes passed to process_madvise"
+    - mm,hwpoison: unmap poisoned page before invalidation
+    - mm/kmemleak: reset tag when compare object pointer
+    - dm stats: fix too short end duration_ns when using precise_timestamps
+    - dm: fix use-after-free in dm_cleanup_zoned_dev()
+    - dm: interlock pending dm_io and dm_wait_for_bios_completion
+    - dm: fix double accounting of flush with data
+    - dm integrity: set journal entry unused when shrinking device
+    - tracing: Have trace event string test handle zero length strings
+    - drbd: fix potential silent data corruption
+    - powerpc/kvm: Fix kvm_use_magic_page
+    - PCI: fu740: Force 2.5GT/s for initial device probe
+    - arm64: signal: nofpsimd: Do not allocate fp/simd context when not available
+    - arm64: Do not defer reserve_crashkernel() for platforms with no DMA memory
+      zones
+    - arm64: dts: qcom: sm8250: Fix MSI IRQ for PCIe1 and PCIe2
+    - arm64: dts: ti: k3-am65: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-j721e: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-j7200: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-am64: Fix gic-v3 compatible regs
+    - ASoC: SOF: Intel: Fix NULL ptr dereference when ENOMEM
+    - Revert "ACPI: Pass the same capabilities to the _OSC regardless of the query
+      flag"
+    - ACPI: properties: Consistently return -ENOENT if there are no more
+      references
+    - coredump: Also dump first pages of non-executable ELF libraries
+    - ext4: fix ext4_fc_stats trace point
+    - ext4: fix fs corruption when tring to remove a non-empty directory with IO
+      error
+    - ext4: make mb_optimize_scan performance mount option work with extents
+    - drivers: hamradio: 6pack: fix UAF bug caused by mod_timer()
+    - samples/landlock: Fix path_list memory leak
+    - landlock: Use square brackets around "landlock-ruleset"
+    - mailbox: tegra-hsp: Flush whole channel
+    - block: limit request dispatch loop duration
+    - block: don't merge across cgroup boundaries if blkcg is enabled
+    - drm/edid: check basic audio support on CEA extension block
+    - fbdev: Hot-unplug firmware fb devices on forced removal
+    - video: fbdev: sm712fb: Fix crash in smtcfb_read()
+    - video: fbdev: atari: Atari 2 bpp (STe) palette bugfix
+    - rfkill: make new event layout opt-in
+    - ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
+    - ARM: dts: at91: sama5d2: Fix PMERRLOC resource size
+    - ARM: dts: exynos: fix UART3 pins configuration in Exynos5250
+    - ARM: dts: exynos: add missing HDMI supplies on SMDK5250
+    - ARM: dts: exynos: add missing HDMI supplies on SMDK5420
+    - mgag200 fix memmapsl configuration in GCTL6 register
+    - carl9170: fix missing bit-wise or operator for tx_params
+    - pstore: Don't use semaphores in always-atomic-context code
+    - thermal: int340x: Increase bitmap size
+    - lib/raid6/test: fix multiple definition linking error
+    - exec: Force single empty string when argv is empty
+    - crypto: rsa-pkcs1pad - only allow with rsa
+    - crypto: rsa-pkcs1pad - correctly get hash from source scatterlist
+    - crypto: rsa-pkcs1pad - restore signature length check
+    - crypto: rsa-pkcs1pad - fix buffer overread in pkcs1pad_verify_complete()
+    - bcache: fixup multiple threads crash
+    - PM: domains: Fix sleep-in-atomic bug caused by genpd_debug_remove()
+    - DEC: Limit PMAX memory probing to R3k systems
+    - media: gpio-ir-tx: fix transmit with long spaces on Orange Pi PC
+    - media: venus: hfi_cmds: List HDR10 property as unsupported for v1 and v3
+    - media: venus: venc: Fix h264 8x8 transform control
+    - media: davinci: vpif: fix unbalanced runtime PM get
+    - media: davinci: vpif: fix unbalanced runtime PM enable
+    - btrfs: zoned: mark relocation as writing
+    - btrfs: extend locking to all space_info members accesses
+    - btrfs: verify the tranisd of the to-be-written dirty extent buffer
+    - xtensa: define update_mmu_tlb function
+    - xtensa: fix stop_machine_cpuslocked call in patch_text
+    - xtensa: fix xtensa_wsr always writing 0
+    - drm/syncobj: flatten dma_fence_chains on transfer
+    - drm/nouveau/backlight: Fix LVDS backlight detection on some laptops
+    - drm/nouveau/backlight: Just set all backlight types as RAW
+    - drm/fb-helper: Mark screen buffers in system memory with FBINFO_VIRTFB
+    - brcmfmac: firmware: Allocate space for default boardrev in nvram
+    - brcmfmac: pcie: Release firmwares in the brcmf_pcie_setup error path
+    - brcmfmac: pcie: Declare missing firmware files in pcie.c
+    - brcmfmac: pcie: Replace brcmf_pcie_copy_mem_todev with memcpy_toio
+    - brcmfmac: pcie: Fix crashes due to early IRQs
+    - drm/i915/opregion: check port number bounds for SWSCI display power state
+    - drm/i915/gem: add missing boundary check in vm_access
+    - PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
+    - PCI: pciehp: Clear cmd_busy bit in polling mode
+    - PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
+    - regulator: qcom_smd: fix for_each_child.cocci warnings
+    - selinux: access superblock_security_struct in LSM blob way
+    - selinux: check return value of sel_make_avc_files
+    - crypto: ccp - Ensure psp_ret is always init'd in
+      __sev_platform_init_locked()
+    - hwrng: cavium - Check health status while reading random data
+    - hwrng: cavium - HW_RANDOM_CAVIUM should depend on ARCH_THUNDER
+    - crypto: sun8i-ss - really disable hash on A80
+    - crypto: authenc - Fix sleep in atomic context in decrypt_tail
+    - crypto: mxs-dcp - Fix scatterlist processing
+    - selinux: Fix selinux_sb_mnt_opts_compat()
+    - thermal: int340x: Check for NULL after calling kmemdup()
+    - crypto: octeontx2 - remove CONFIG_DM_CRYPT check
+    - spi: tegra114: Add missing IRQ check in tegra_spi_probe
+    - spi: tegra210-quad: Fix missin IRQ check in tegra_qspi_probe
+    - stack: Constrain and fix stack offset randomization with Clang builds
+    - arm64/mm: avoid fixmap race condition when create pud mapping
+    - blk-cgroup: set blkg iostat after percpu stat aggregation
+    - selftests/x86: Add validity check and allow field splitting
+    - selftests/sgx: Treat CC as one argument
+    - crypto: rockchip - ECB does not need IV
+    - audit: log AUDIT_TIME_* records only from rules
+    - EVM: fix the evm= __setup handler return value
+    - crypto: ccree - don't attempt 0 len DMA mappings
+    - crypto: hisilicon/sec - fix the aead software fallback for engine
+    - spi: pxa2xx-pci: Balance reference count for PCI DMA device
+    - hwmon: (pmbus) Add mutex to regulator ops
+    - hwmon: (sch56xx-common) Replace WDOG_ACTIVE with WDOG_HW_RUNNING
+    - nvme: cleanup __nvme_check_ids
+    - nvme: fix the check for duplicate unique identifiers
+    - block: don't delete queue kobject before its children
+    - PM: hibernate: fix __setup handler error handling
+    - PM: suspend: fix return value of __setup handler
+    - spi: spi-zynqmp-gqspi: Handle error for dma_set_mask
+    - hwrng: atmel - disable trng on failure path
+    - crypto: sun8i-ss - call finalize with bh disabled
+    - crypto: sun8i-ce - call finalize with bh disabled
+    - crypto: amlogic - call finalize with bh disabled
+    - crypto: gemini - call finalize with bh disabled
+    - crypto: vmx - add missing dependencies
+    - clocksource/drivers/timer-ti-dm: Fix regression from errata i940 fix
+    - clocksource/drivers/exynos_mct: Refactor resources allocation
+    - clocksource/drivers/exynos_mct: Handle DTS with higher number of interrupts
+    - clocksource/drivers/timer-microchip-pit64b: Use notrace
+    - clocksource/drivers/timer-of: Check return value of of_iomap in
+      timer_of_base_init()
+    - arm64: prevent instrumentation of bp hardening callbacks
+    - KEYS: trusted: Fix trusted key backends when building as module
+    - KEYS: trusted: Avoid calling null function trusted_key_exit
+    - ACPI: APEI: fix return value of __setup handlers
+    - crypto: ccp - ccp_dmaengine_unregister release dma channels
+    - crypto: ccree - Fix use after free in cc_cipher_exit()
+    - hwrng: nomadik - Change clk_disable to clk_disable_unprepare
+    - hwmon: (pmbus) Add Vin unit off handling
+    - clocksource: acpi_pm: fix return value of __setup handler
+    - io_uring: don't check unrelated req->open.how in accept request
+    - io_uring: terminate manual loop iterator loop correctly for non-vecs
+    - watch_queue: Fix NULL dereference in error cleanup
+    - watch_queue: Actually free the watch
+    - f2fs: fix to enable ATGC correctly via gc_idle sysfs interface
+    - sched/debug: Remove mpol_get/put and task_lock/unlock from sched_show_numa
+    - sched/core: Export pelt_thermal_tp
+    - sched/uclamp: Fix iowait boost escaping uclamp restriction
+    - rseq: Remove broken uapi field layout on 32-bit little endian
+    - perf/core: Fix address filter parser for multiple filters
+    - perf/x86/intel/pt: Fix address filter config for 32-bit kernel
+    - sched/fair: Improve consistency of allowed NUMA balance calculations
+    - f2fs: fix missing free nid in f2fs_handle_failed_inode
+    - nfsd: more robust allocation failure handling in nfsd_file_cache_init
+    - sched/cpuacct: Fix charge percpu cpuusage
+    - sched/rt: Plug rt_mutex_setprio() vs push_rt_task() race
+    - f2fs: fix to avoid potential deadlock
+    - btrfs: fix unexpected error path when reflinking an inline extent
+    - f2fs: fix compressed file start atomic write may cause data corruption
+    - selftests, x86: fix how check_cc.sh is being invoked
+    - drivers/base/memory: add memory block to memory group after registration
+      succeeded
+    - kunit: make kunit_test_timeout compatible with comment
+    - pinctrl: samsung: Remove EINT handler for Exynos850 ALIVE and CMGP gpios
+    - media: staging: media: zoran: fix usage of vb2_dma_contig_set_max_seg_size
+    - media: camss: csid-170: fix non-10bit formats
+    - media: camss: csid-170: don't enable unused irqs
+    - media: camss: csid-170: set the right HALT_CMD when disabled
+    - media: camss: vfe-170: fix "VFE halt timeout" error
+    - media: staging: media: imx: imx7-mipi-csis: Make subdev name unique
+    - media: v4l2-mem2mem: Apply DST_QUEUE_OFF_BASE on MMAP buffers across ioctls
+    - media: mtk-vcodec: potential dereference of null pointer
+    - media: imx: imx8mq-mipi-csi2: remove wrong irq config write operation
+    - media: imx: imx8mq-mipi_csi2: fix system resume
+    - media: bttv: fix WARNING regression on tunerless devices
+    - media: atmel: atmel-sama7g5-isc: fix ispck leftover
+    - ASoC: sh: rz-ssi: Drop calling rz_ssi_pio_recv() recursively
+    - ASoC: codecs: Check for error pointer after calling devm_regmap_init_mmio
+    - ASoC: xilinx: xlnx_formatter_pcm: Handle sysclk setting
+    - ASoC: simple-card-utils: Set sysclk on all components
+    - media: coda: Fix missing put_device() call in coda_get_vdoa_data
+    - media: meson: vdec: potential dereference of null pointer
+    - media: hantro: Fix overfill bottom register field name
+    - media: ov6650: Fix set format try processing path
+    - media: v4l: Avoid unaligned access warnings when printing 4cc modifiers
+    - media: ov5648: Don't pack controls struct
+    - media: aspeed: Correct value for h-total-pixels
+    - video: fbdev: matroxfb: set maxvram of vbG200eW to the same as vbG200 to
+      avoid black screen
+    - video: fbdev: controlfb: Fix COMPILE_TEST build
+    - video: fbdev: smscufx: Fix null-ptr-deref in ufx_usb_probe()
+    - video: fbdev: atmel_lcdfb: fix an error code in atmel_lcdfb_probe()
+    - video: fbdev: fbcvt.c: fix printing in fb_cvt_print_name()
+    - ARM: dts: Fix OpenBMC flash layout label addresses
+    - firmware: qcom: scm: Remove reassignment to desc following initializer
+    - ARM: dts: qcom: ipq4019: fix sleep clock
+    - soc: qcom: rpmpd: Check for null return of devm_kcalloc
+    - soc: qcom: ocmem: Fix missing put_device() call in of_get_ocmem
+    - soc: qcom: aoss: remove spurious IRQF_ONESHOT flags
+    - arm64: dts: qcom: sdm845: fix microphone bias properties and values
+    - arm64: dts: qcom: sm8250: fix PCIe bindings to follow schema
+    - arm64: dts: broadcom: bcm4908: use proper TWD binding
+    - arm64: dts: qcom: sm8150: Correct TCS configuration for apps rsc
+    - arm64: dts: qcom: sm8350: Correct TCS configuration for apps rsc
+    - firmware: ti_sci: Fix compilation failure when CONFIG_TI_SCI_PROTOCOL is not
+      defined
+    - soc: ti: wkup_m3_ipc: Fix IRQ check in wkup_m3_ipc_probe
+    - ARM: dts: sun8i: v3s: Move the csi1 block to follow address order
+    - vsprintf: Fix potential unaligned access
+    - ARM: dts: imx: Add missing LVDS decoder on M53Menlo
+    - media: mexon-ge2d: fixup frames size in registers
+    - media: video/hdmi: handle short reads of hdmi info frame.
+    - media: ti-vpe: cal: Fix a NULL pointer dereference in
+      cal_ctx_v4l2_init_formats()
+    - media: em28xx: initialize refcount before kref_get
+    - media: usb: go7007: s2250-board: fix leak in probe()
+    - media: cedrus: H265: Fix neighbour info buffer size
+    - media: cedrus: h264: Fix neighbour info buffer size
+    - ASoC: codecs: rx-macro: fix accessing compander for aux
+    - ASoC: codecs: rx-macro: fix accessing array out of bounds for enum type
+    - ASoC: codecs: va-macro: fix accessing array out of bounds for enum type
+    - ASoC: codecs: wc938x: fix accessing array out of bounds for enum type
+    - ASoC: codecs: wcd938x: fix kcontrol max values
+    - ASoC: codecs: wcd934x: fix kcontrol max values
+    - ASoC: codecs: wcd934x: fix return value of wcd934x_rx_hph_mode_put
+    - media: v4l2-core: Initialize h264 scaling matrix
+    - media: ov5640: Fix set format, v4l2_mbus_pixelcode not updated
+    - selftests/lkdtm: Add UBSAN config
+    - lib: uninline simple_strntoull() as well
+    - vsprintf: Fix %pK with kptr_restrict == 0
+    - uaccess: fix nios2 and microblaze get_user_8()
+    - ASoC: rt5663: check the return value of devm_kzalloc() in rt5663_parse_dp()
+    - soc: mediatek: pm-domains: Add wakeup capacity support in power domain
+    - mmc: sdhci_am654: Fix the driver data of AM64 SoC
+    - ASoC: ti: davinci-i2s: Add check for clk_enable()
+    - ALSA: spi: Add check for clk_enable()
+    - arm64: dts: ns2: Fix spi-cpol and spi-cpha property
+    - arm64: dts: broadcom: Fix sata nodename
+    - printk: fix return value of printk.devkmsg __setup handler
+    - ASoC: mxs-saif: Handle errors for clk_enable
+    - ASoC: atmel_ssc_dai: Handle errors for clk_enable
+    - ASoC: dwc-i2s: Handle errors for clk_enable
+    - ASoC: soc-compress: prevent the potentially use of null pointer
+    - memory: emif: Add check for setup_interrupts
+    - memory: emif: check the pointer temp in get_device_details()
+    - ALSA: firewire-lib: fix uninitialized flag for AV/C deferred transaction
+    - arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
+    - m68k: coldfire/device.c: only build for MCF_EDMA when h/w macros are defined
+    - media: stk1160: If start stream fails, return buffers with
+      VB2_BUF_STATE_QUEUED
+    - media: vidtv: Check for null return of vzalloc
+    - ASoC: atmel: Add missing of_node_put() in at91sam9g20ek_audio_probe
+    - ASoC: wm8350: Handle error for wm8350_register_irq
+    - ASoC: fsi: Add check for clk_enable
+    - video: fbdev: omapfb: Add missing of_node_put() in dvic_probe_of
+    - media: saa7134: fix incorrect use to determine if list is empty
+    - ivtv: fix incorrect device_caps for ivtvfb
+    - ASoC: atmel: Fix error handling in snd_proto_probe
+    - ASoC: rockchip: i2s: Fix missing clk_disable_unprepare() in
+      rockchip_i2s_probe
+    - ASoC: SOF: Add missing of_node_put() in imx8m_probe
+    - ASoC: mediatek: use of_device_get_match_data()
+    - ASoC: mediatek: mt8192-mt6359: Fix error handling in mt8192_mt6359_dev_probe
+    - ASoC: rk817: Fix missing clk_disable_unprepare() in rk817_platform_probe
+    - ASoC: dmaengine: do not use a NULL prepare_slave_config() callback
+    - ASoC: mxs: Fix error handling in mxs_sgtl5000_probe
+    - ASoC: fsl_spdif: Disable TX clock when stop
+    - ASoC: imx-es8328: Fix error return code in imx_es8328_probe()
+    - ASoC: SOF: Intel: enable DMI L1 for playback streams
+    - ASoC: msm8916-wcd-digital: Fix missing clk_disable_unprepare() in
+      msm8916_wcd_digital_probe
+    - mmc: davinci_mmc: Handle error for clk_enable
+    - ASoC: atmel: Fix error handling in sam9x5_wm8731_driver_probe
+    - ASoC: msm8916-wcd-analog: Fix error handling in pm8916_wcd_analog_spmi_probe
+    - ASoC: codecs: wcd934x: Add missing of_node_put() in wcd934x_codec_parse_data
+    - ASoC: amd: Fix reference to PCM buffer address
+    - ARM: configs: multi_v5_defconfig: re-enable CONFIG_V4L_PLATFORM_DRIVERS
+    - ARM: configs: multi_v5_defconfig: re-enable DRM_PANEL and FB_xxx
+    - drm/meson: osd_afbcd: Add an exit callback to struct meson_afbcd_ops
+    - drm/meson: Make use of the helper function
+      devm_platform_ioremap_resourcexxx()
+    - drm/meson: split out encoder from meson_dw_hdmi
+    - drm/meson: Fix error handling when afbcd.ops->init fails
+    - drm/bridge: Fix free wrong object in sii8620_init_rcp_input_dev
+    - drm/bridge: Add missing pm_runtime_disable() in __dw_mipi_dsi_probe
+    - drm/bridge: nwl-dsi: Fix PM disable depth imbalance in nwl_dsi_probe
+    - drm: bridge: adv7511: Fix ADV7535 HPD enablement
+    - ath10k: fix memory overwrite of the WoWLAN wakeup packet pattern
+    - drm/v3d/v3d_drv: Check for error num after setting mask
+    - drm/panfrost: Check for error num after setting mask
+    - libbpf: Fix possible NULL pointer dereference when destroying skeleton
+    - bpftool: Only set obj->skeleton on complete success
+    - udmabuf: validate ubuf->pagecount
+    - bpf: Fix UAF due to race between btf_try_get_module and load_module
+    - drm/selftests/test-drm_dp_mst_helper: Fix memory leak in
+      sideband_msg_req_encode_decode
+    - selftests: bpf: Fix bind on used port
+    - Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
+    - Bluetooth: hci_serdev: call init_rwsem() before p->open()
+    - mtd: onenand: Check for error irq
+    - mtd: rawnand: gpmi: fix controller timings setting
+    - drm/edid: Don't clear formats if using deep color
+    - drm/edid: Split deep color modes between RGB and YUV444
+    - ionic: fix type complaint in ionic_dev_cmd_clean()
+    - ionic: start watchdog after all is setup
+    - ionic: Don't send reset commands if FW isn't running
+    - drm/nouveau/acr: Fix undefined behavior in nvkm_acr_hsfw_load_bl()
+    - drm/amd/display: Fix a NULL pointer dereference in
+      amdgpu_dm_connector_add_common_modes()
+    - drm/amd/pm: return -ENOTSUPP if there is no get_dpm_ultimate_freq function
+    - net: phy: at803x: move page selection fix to config_init
+    - selftests/bpf: Normalize XDP section names in selftests
+    - selftests/bpf/test_xdp_redirect_multi: use temp netns for testing
+    - ath9k_htc: fix uninit value bugs
+    - RDMA/core: Set MR type in ib_reg_user_mr
+    - KVM: PPC: Fix vmx/vsx mixup in mmio emulation
+    - selftests/net: timestamping: Fix bind_phc check
+    - i40e: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - i40e: respect metadata on XSK Rx to skb
+    - igc: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - ixgbe: pass bi->xdp to ixgbe_construct_skb_zc() directly
+    - ixgbe: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - ixgbe: respect metadata on XSK Rx to skb
+    - power: reset: gemini-poweroff: Fix IRQ check in gemini_poweroff_probe
+    - ray_cs: Check ioremap return value
+    - powerpc: dts: t1040rdb: fix ports names for Seville Ethernet switch
+    - KVM: PPC: Book3S HV: Check return value of kvmppc_radix_init
+    - powerpc/perf: Don't use perf_hw_context for trace IMC PMU
+    - mt76: connac: fix sta_rec_wtbl tag len
+    - mt76: mt7915: use proper aid value in mt7915_mcu_wtbl_generic_tlv in sta
+      mode
+    - mt76: mt7915: use proper aid value in mt7915_mcu_sta_basic_tlv
+    - mt76: mt7921: fix a leftover race in runtime-pm
+    - mt76: mt7615: fix a leftover race in runtime-pm
+    - mt76: mt7603: check sta_rates pointer in mt7603_sta_rate_tbl_update
+    - mt76: mt7615: check sta_rates pointer in mt7615_sta_rate_tbl_update
+    - ptp: unregister virtual clocks when unregistering physical clock.
+    - net: dsa: mv88e6xxx: Enable port policy support on 6097
+    - mac80211: Remove a couple of obsolete TODO
+    - mac80211: limit bandwidth in HE capabilities
+    - scripts/dtc: Call pkg-config POSIXly correct
+    - livepatch: Fix build failure on 32 bits processors
+    - net: asix: add proper error handling of usb read errors
+    - i2c: bcm2835: Use platform_get_irq() to get the interrupt
+    - i2c: bcm2835: Fix the error handling in 'bcm2835_i2c_probe()'
+    - mtd: mchp23k256: Add SPI ID table
+    - mtd: mchp48l640: Add SPI ID table
+    - igc: avoid kernel warning when changing RX ring parameters
+    - igb: refactor XDP registration
+    - PCI: aardvark: Fix reading MSI interrupt number
+    - PCI: aardvark: Fix reading PCI_EXP_RTSTA_PME bit on emulated bridge
+    - RDMA/rxe: Check the last packet by RXE_END_MASK
+    - libbpf: Fix signedness bug in btf_dump_array_data()
+    - cxl/core: Fix cxl_probe_component_regs() error message
+    - cxl/regs: Fix size of CXL Capability Header Register
+    - net:enetc: allocate CBD ring data memory using DMA coherent methods
+    - libbpf: Fix compilation warning due to mismatched printf format
+    - drm/bridge: dw-hdmi: use safe format when first in bridge chain
+    - libbpf: Use dynamically allocated buffer when receiving netlink messages
+    - power: supply: ab8500: Fix memory leak in ab8500_fg_sysfs_init
+    - HID: i2c-hid: fix GET/SET_REPORT for unnumbered reports
+    - iommu/ipmmu-vmsa: Check for error num after setting mask
+    - drm/bridge: anx7625: Fix overflow issue on reading EDID
+    - bpftool: Fix the error when lookup in no-btf maps
+    - drm/amd/pm: enable pm sysfs write for one VF mode
+    - drm/amd/display: Add affected crtcs to atomic state for dsc mst unplug
+    - libbpf: Fix memleak in libbpf_netlink_recv()
+    - IB/cma: Allow XRC INI QPs to set their local ACK timeout
+    - dax: make sure inodes are flushed before destroy cache
+    - selftests: mptcp: add csum mib check for mptcp_connect
+    - iwlwifi: mvm: Don't call iwl_mvm_sta_from_mac80211() with NULL sta
+    - iwlwifi: mvm: don't iterate unadded vifs when handling FW SMPS req
+    - iwlwifi: mvm: align locking in D3 test debugfs
+    - iwlwifi: yoyo: remove DBGI_SRAM address reset writing
+    - iwlwifi: Fix -EIO error code that is never returned
+    - iwlwifi: mvm: Fix an error code in iwl_mvm_up()
+    - mtd: rawnand: pl353: Set the nand chip node as the flash node
+    - drm/msm/dp: populate connector of struct dp_panel
+    - drm/msm/dp: stop link training after link training 2 failed
+    - drm/msm/dp: always add fail-safe mode into connector mode list
+    - drm/msm/dsi: Use "ref" fw clock instead of global name for VCO parent
+    - drm/msm/dsi/phy: fix 7nm v4.0 settings for C-PHY mode
+    - drm/msm/dpu: add DSPP blocks teardown
+    - drm/msm/dpu: fix dp audio condition
+    - dm crypt: fix get_key_size compiler warning if !CONFIG_KEYS
+    - vfio/pci: fix memory leak during D3hot to D0 transition
+    - vfio/pci: wake-up devices around reset functions
+    - scsi: fnic: Fix a tracing statement
+    - scsi: pm8001: Fix command initialization in pm80XX_send_read_log()
+    - scsi: pm8001: Fix command initialization in pm8001_chip_ssp_tm_req()
+    - scsi: pm8001: Fix payload initialization in pm80xx_set_thermal_config()
+    - scsi: pm8001: Fix le32 values handling in
+      pm80xx_set_sas_protocol_timer_config()
+    - scsi: pm8001: Fix payload initialization in pm80xx_encrypt_update()
+    - scsi: pm8001: Fix le32 values handling in pm80xx_chip_ssp_io_req()
+    - scsi: pm8001: Fix le32 values handling in pm80xx_chip_sata_req()
+    - scsi: pm8001: Fix NCQ NON DATA command task initialization
+    - scsi: pm8001: Fix NCQ NON DATA command completion handling
+    - scsi: pm8001: Fix abort all task initialization
+    - RDMA/mlx5: Fix the flow of a miss in the allocation of a cache ODP MR
+    - drm/amd/display: Remove vupdate_int_entry definition
+    - TOMOYO: fix __setup handlers return values
+    - power: supply: sbs-charger: Don't cancel work that is not initialized
+    - ext2: correct max file size computing
+    - drm/tegra: Fix reference leak in tegra_dsi_ganged_probe
+    - power: supply: bq24190_charger: Fix bq24190_vbus_is_enabled() wrong false
+      return
+    - scsi: hisi_sas: Change permission of parameter prot_mask
+    - drm/bridge: cdns-dsi: Make sure to to create proper aliases for dt
+    - bpf, arm64: Call build_prologue() first in first JIT pass
+    - bpf, arm64: Feed byte-offset into bpf line info
+    - xsk: Fix race at socket teardown
+    - RDMA/irdma: Fix netdev notifications for vlan's
+    - RDMA/irdma: Fix Passthrough mode in VM
+    - RDMA/irdma: Remove incorrect masking of PD
+    - gpu: host1x: Fix a memory leak in 'host1x_remove()'
+    - libbpf: Skip forward declaration when counting duplicated type names
+    - powerpc/mm/numa: skip NUMA_NO_NODE onlining in parse_numa_properties()
+    - powerpc/Makefile: Don't pass -mcpu=powerpc64 when building 32-bit
+    - KVM: x86: Fix emulation in writing cr8
+    - KVM: x86/emulator: Defer not-present segment check in
+      __load_segment_descriptor()
+    - hv_balloon: rate-limit "Unhandled message" warning
+    - i2c: xiic: Make bus names unique
+    - power: supply: wm8350-power: Handle error for wm8350_register_irq
+    - power: supply: wm8350-power: Add missing free in free_charger_irq
+    - IB/hfi1: Allow larger MTU without AIP
+    - RDMA/core: Fix ib_qp_usecnt_dec() called when error
+    - PCI: Reduce warnings on possible RW1C corruption
+    - net: axienet: fix RX ring refill allocation failure handling
+    - drm/msm/a6xx: Fix missing ARRAY_SIZE() check
+    - mips: DEC: honor CONFIG_MIPS_FP_SUPPORT=n
+    - MIPS: Sanitise Cavium switch cases in TLB handler synthesizers
+    - powerpc/sysdev: fix incorrect use to determine if list is empty
+    - powerpc/64s: Don't use DSISR for SLB faults
+    - mfd: mc13xxx: Add check for mc13xxx_irq_request
+    - libbpf: Unmap rings when umem deleted
+    - selftests/bpf: Make test_lwt_ip_encap more stable and faster
+    - platform/x86: huawei-wmi: check the return value of device_create_file()
+    - scsi: mpt3sas: Fix incorrect 4GB boundary check
+    - powerpc: 8xx: fix a return value error in mpc8xx_pic_init
+    - vxcan: enable local echo for sent CAN frames
+    - ath10k: Fix error handling in ath10k_setup_msa_resources
+    - mips: cdmm: Fix refcount leak in mips_cdmm_phys_base
+    - MIPS: RB532: fix return value of __setup handler
+    - MIPS: pgalloc: fix memory leak caused by pgd_free()
+    - mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
+    - power: ab8500_chargalg: Use CLOCK_MONOTONIC
+    - RDMA/irdma: Prevent some integer underflows
+    - Revert "RDMA/core: Fix ib_qp_usecnt_dec() called when error"
+    - RDMA/mlx5: Fix memory leak in error flow for subscribe event routine
+    - bpf, sockmap: Fix memleak in sk_psock_queue_msg
+    - bpf, sockmap: Fix memleak in tcp_bpf_sendmsg while sk msg is full
+    - bpf, sockmap: Fix more uncharged while msg has more_data
+    - bpf, sockmap: Fix double uncharge the mem of sk_msg
+    - samples/bpf, xdpsock: Fix race when running for fix duration of time
+    - USB: storage: ums-realtek: fix error code in rts51x_read_mem()
+    - drm/i915/display: Fix HPD short pulse handling for eDP
+    - netfilter: flowtable: Fix QinQ and pppoe support for inet table
+    - mt76: mt7921: fix mt7921_queues_acq implementation
+    - can: isotp: sanitize CAN ID checks in isotp_bind()
+    - can: isotp: return -EADDRNOTAVAIL when reading from unbound socket
+    - can: isotp: support MSG_TRUNC flag when reading from socket
+    - bareudp: use ipv6_mod_enabled to check if IPv6 enabled
+    - ibmvnic: fix race between xmit and reset
+    - af_unix: Fix some data-races around unix_sk(sk)->oob_skb.
+    - selftests/bpf: Fix error reporting from sock_fields programs
+    - Bluetooth: hci_uart: add missing NULL check in h5_enqueue
+    - Bluetooth: call hci_le_conn_failed with hdev lock in hci_le_conn_failed
+    - Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interrupt
+    - ipv4: Fix route lookups when handling ICMP redirects and PMTU updates
+    - af_netlink: Fix shift out of bounds in group mask calculation
+    - i2c: meson: Fix wrong speed use from probe
+    - netfilter: conntrack: Add and use nf_ct_set_auto_assign_helper_warned()
+    - i2c: mux: demux-pinctrl: do not deactivate a master that is not active
+    - powerpc/pseries: Fix use after free in remove_phb_dynamic()
+    - selftests/bpf/test_lirc_mode2.sh: Exit with proper code
+    - PCI: Avoid broken MSI on SB600 USB devices
+    - net: bcmgenet: Use stronger register read/writes to assure ordering
+    - tcp: ensure PMTU updates are processed during fastopen
+    - openvswitch: always update flow key after nat
+    - net: dsa: fix panic on shutdown if multi-chip tree failed to probe
+    - tipc: fix the timer expires after interval 100ms
+    - mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
+    - ice: fix 'scheduling while atomic' on aux critical err interrupt
+    - ice: don't allow to run ice_send_event_to_aux() in atomic ctx
+    - drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via
+      ethtool
+    - kernel/resource: fix kfree() of bootmem memory again
+    - staging: r8188eu: convert DBG_88E_LEVEL call in hal/rtl8188e_hal_init.c
+    - staging: r8188eu: release_firmware is not called if allocation fails
+    - mxser: fix xmit_buf leak in activate when LSR == 0xff
+    - fsi: scom: Fix error handling
+    - fsi: scom: Remove retries in indirect scoms
+    - pwm: lpc18xx-sct: Initialize driver data and hardware before pwmchip_add()
+    - pps: clients: gpio: Propagate return value from pps_gpio_probe
+    - fsi: Aspeed: Fix a potential double free
+    - misc: alcor_pci: Fix an error handling path
+    - cpufreq: qcom-cpufreq-nvmem: fix reading of PVS Valid fuse
+    - soundwire: intel: fix wrong register name in intel_shim_wake
+    - clk: qcom: ipq8074: fix PCI-E clock oops
+    - dmaengine: idxd: check GENCAP config support for gencfg register
+    - dmaengine: idxd: change bandwidth token to read buffers
+    - dmaengine: idxd: restore traffic class defaults after wq reset
+    - iio: mma8452: Fix probe failing when an i2c_device_id is used
+    - serial: 8250_aspeed_vuart: add PORT_ASPEED_VUART port type
+    - staging:iio:adc:ad7280a: Fix handing of device address bit reversing.
+    - pinctrl: renesas: r8a77470: Reduce size for narrow VIN1 channel
+    - pinctrl: renesas: checker: Fix miscalculation of number of states
+    - clk: qcom: ipq8074: Use floor ops for SDCC1 clock
+    - phy: dphy: Correct lpx parameter and its derivatives(ta_{get,go,sure})
+    - phy: phy-brcm-usb: fixup BCM4908 support
+    - serial: 8250_mid: Balance reference count for PCI DMA device
+    - serial: 8250_lpss: Balance reference count for PCI DMA device
+    - NFS: Use of mapping_set_error() results in spurious errors
+    - serial: 8250: Fix race condition in RTS-after-send handling
+    - iio: adc: Add check for devm_request_threaded_irq
+    - habanalabs: Add check for pci_enable_device
+    - NFS: Return valid errors from nfs2/3_decode_dirent()
+    - staging: r8188eu: fix endless loop in recv_func
+    - dma-debug: fix return value of __setup handlers
+    - clk: imx7d: Remove audio_mclk_root_clk
+    - clk: imx: off by one in imx_lpcg_parse_clks_from_dt()
+    - clk: at91: sama7g5: fix parents of PDMCs' GCLK
+    - clk: qcom: clk-rcg2: Update logic to calculate D value for RCG
+    - clk: qcom: clk-rcg2: Update the frac table for pixel clock
+    - dmaengine: hisi_dma: fix MSI allocate fail when reload hisi_dma
+    - remoteproc: qcom: Fix missing of_node_put in adsp_alloc_memory_region
+    - remoteproc: qcom_wcnss: Add missing of_node_put() in
+      wcnss_alloc_memory_region
+    - remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_region
+    - nvdimm/region: Fix default alignment for small regions
+    - clk: actions: Terminate clk_div_table with sentinel element
+    - clk: loongson1: Terminate clk_div_table with sentinel element
+    - clk: hisilicon: Terminate clk_div_table with sentinel element
+    - clk: clps711x: Terminate clk_div_table with sentinel element
+    - clk: Fix clk_hw_get_clk() when dev is NULL
+    - clk: tegra: tegra124-emc: Fix missing put_device() call in
+      emc_ensure_emc_driver
+    - mailbox: imx: fix crash in resume on i.mx8ulp
+    - NFS: remove unneeded check in decode_devicenotify_args()
+    - staging: mt7621-dts: fix LEDs and pinctrl on GB-PC1 devicetree
+    - staging: mt7621-dts: fix formatting
+    - staging: mt7621-dts: fix pinctrl properties for ethernet
+    - staging: mt7621-dts: fix GB-PC2 devicetree
+    - pinctrl: mediatek: Fix missing of_node_put() in mtk_pctrl_init
+    - pinctrl: mediatek: paris: Fix PIN_CONFIG_BIAS_* readback
+    - pinctrl: mediatek: paris: Fix "argument" argument type for mtk_pinconf_get()
+    - pinctrl: mediatek: paris: Fix pingroup pin config state readback
+    - pinctrl: mediatek: paris: Skip custom extra pin config dump for virtual
+      GPIOs
+    - pinctrl: microchip sgpio: use reset driver
+    - pinctrl: microchip-sgpio: lock RMW access
+    - pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
+    - pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
+    - tty: hvc: fix return value of __setup handler
+    - kgdboc: fix return value of __setup handler
+    - serial: 8250: fix XOFF/XON sending when DMA is used
+    - virt: acrn: obtain pa from VMA with PFNMAP flag
+    - virt: acrn: fix a memory leak in acrn_dev_ioctl()
+    - kgdbts: fix return value of __setup handler
+    - firmware: google: Properly state IOMEM dependency
+    - driver core: dd: fix return value of __setup handler
+    - jfs: fix divide error in dbNextAG
+    - netfilter: nf_conntrack_tcp: preserve liberal flag in tcp options
+    - SUNRPC don't resend a task on an offlined transport
+    - NFSv4.1: don't retry BIND_CONN_TO_SESSION on session error
+    - kdb: Fix the putarea helper function
+    - perf stat: Fix forked applications enablement of counters
+    - clk: qcom: gcc-msm8994: Fix gpll4 width
+    - vsock/virtio: initialize vdev->priv before using VQs
+    - vsock/virtio: read the negotiated features before using VQs
+    - vsock/virtio: enable VQs early on probe
+    - clk: Initialize orphan req_rate
+    - xen: fix is_xen_pmu()
+    - net: enetc: report software timestamping via SO_TIMESTAMPING
+    - net: hns3: fix bug when PF set the duplicate MAC address for VFs
+    - net: hns3: fix port base vlan add fail when concurrent with reset
+    - net: hns3: add vlan list lock to protect vlan list
+    - net: hns3: format the output of the MAC address
+    - net: hns3: refine the process when PF set VF VLAN
+    - net: phy: broadcom: Fix brcm_fet_config_init()
+    - selftests: test_vxlan_under_vrf: Fix broken test case
+    - NFS: Don't loop forever in nfs_do_recoalesce()
+    - net: hns3: clean residual vf config after disable sriov
+    - net: sparx5: depends on PTP_1588_CLOCK_OPTIONAL
+    - qlcnic: dcb: default to returning -EOPNOTSUPP
+    - net/x25: Fix null-ptr-deref caused by x25_disconnect
+    - net: sparx5: switchdev: fix possible NULL pointer dereference
+    - octeontx2-af: initialize action variable
+    - net: prefer nf_ct_put instead of nf_conntrack_put
+    - net/sched: act_ct: fix ref leak when switching zones
+    - NFSv4/pNFS: Fix another issue with a list iterator pointing to the head
+    - net: dsa: bcm_sf2_cfp: fix an incorrect NULL check on list iterator
+    - fs: fd tables have to be multiples of BITS_PER_LONG
+    - lib/test: use after free in register_test_dev_kmod()
+    - fs: fix fd table size alignment properly
+    - LSM: general protection fault in legacy_parse_param
+    - regulator: rpi-panel: Handle I2C errors/timing to the Atmel
+    - crypto: hisilicon/qm - cleanup warning in qm_vf_read_qos
+    - gcc-plugins/stackleak: Exactly match strings instead of prefixes
+    - pinctrl: npcm: Fix broken references to chip->parent_device
+    - rcu: Mark writes to the rcu_segcblist structure's ->flags field
+    - block/bfq_wf2q: correct weight to ioprio
+    - crypto: xts - Add softdep on ecb
+    - crypto: hisilicon/sec - not need to enable sm4 extra mode at HW V3
+    - block, bfq: don't move oom_bfqq
+    - selinux: use correct type for context length
+    - arm64: module: remove (NOLOAD) from linker script
+    - selinux: allow FIOCLEX and FIONCLEX with policy capability
+    - loop: use sysfs_emit() in the sysfs xxx show()
+    - Fix incorrect type in assignment of ipv6 port for audit
+    - irqchip/qcom-pdc: Fix broken locking
+    - irqchip/nvic: Release nvic_base upon failure
+    - fs/binfmt_elf: Fix AT_PHDR for unusual ELF files
+    - bfq: fix use-after-free in bfq_dispatch_request
+    - ACPICA: Avoid walking the ACPI Namespace if it is not there
+    - lib/raid6/test/Makefile: Use $(pound) instead of \# for Make 4.3
+    - Revert "Revert "block, bfq: honor already-setup queue merges""
+    - ACPI/APEI: Limit printable size of BERT table data
+    - PM: core: keep irq flags in device_pm_check_callbacks()
+    - parisc: Fix handling off probe non-access faults
+    - nvme-tcp: lockdep: annotate in-kernel sockets
+    - spi: tegra20: Use of_device_get_match_data()
+    - atomics: Fix atomic64_{read_acquire,set_release} fallbacks
+    - locking/lockdep: Iterate lock_classes directly when reading lockdep files
+    - ext4: correct cluster len and clusters changed accounting in ext4_mb_mark_bb
+    - ext4: fix ext4_mb_mark_bb() with flex_bg with fast_commit
+    - sched/tracing: Report TASK_RTLOCK_WAIT tasks as TASK_UNINTERRUPTIBLE
+    - ext4: don't BUG if someone dirty pages without asking ext4 first
+    - f2fs: fix to do sanity check on curseg->alloc_type
+    - NFSD: Fix nfsd_breaker_owns_lease() return values
+    - f2fs: don't get FREEZE lock in f2fs_evict_inode in frozen fs
+    - btrfs: harden identification of a stale device
+    - btrfs: make search_csum_tree return 0 if we get -EFBIG
+    - f2fs: use spin_lock to avoid hang
+    - f2fs: compress: fix to print raw data size in error path of lz4
+      decompression
+    - Adjust cifssb maximum read size
+    - ntfs: add sanity check on allocation size
+    - media: staging: media: zoran: move videodev alloc
+    - media: staging: media: zoran: calculate the right buffer number for
+      zoran_reap_stat_com
+    - media: staging: media: zoran: fix various V4L2 compliance errors
+    - media: atmel: atmel-isc-base: report frame sizes as full supported range
+    - media: ir_toy: free before error exiting
+    - ASoC: sh: rz-ssi: Make the data structures available before registering the
+      handlers
+    - ASoC: SOF: Intel: match sdw version on link_slaves_found
+    - media: imx-jpeg: Prevent decoding NV12M jpegs into single-planar buffers
+    - media: iommu/mediatek-v1: Free the existed fwspec if the master dev already
+      has
+    - media: iommu/mediatek: Return ENODEV if the device is NULL
+    - media: iommu/mediatek: Add device_link between the consumer and the larb
+      devices
+    - video: fbdev: nvidiafb: Use strscpy() to prevent buffer overflow
+    - video: fbdev: w100fb: Reset global state
+    - video: fbdev: cirrusfb: check pixclock to avoid divide by zero
+    - video: fbdev: omapfb: acx565akm: replace snprintf with sysfs_emit
+    - ARM: dts: qcom: fix gic_irq_domain_translate warnings for msm8960
+    - ARM: dts: bcm2837: Add the missing L1/L2 cache information
+    - ASoC: madera: Add dependencies on MFD
+    - media: atomisp_gmin_platform: Add DMI quirk to not turn AXP ELDO2 regulator
+      off on some boards
+    - media: atomisp: fix dummy_ptr check to avoid duplicate active_bo
+    - ARM: ftrace: avoid redundant loads or clobbering IP
+    - ARM: dts: imx7: Use audio_mclk_post_div instead audio_mclk_root_clk
+    - arm64: defconfig: build imx-sdma as a module
+    - video: fbdev: omapfb: panel-dsi-cm: Use sysfs_emit() instead of snprintf()
+    - video: fbdev: omapfb: panel-tpo-td043mtea1: Use sysfs_emit() instead of
+      snprintf()
+    - video: fbdev: udlfb: replace snprintf in show functions with sysfs_emit
+    - ARM: dts: bcm2711: Add the missing L1/L2 cache information
+    - ASoC: soc-core: skip zero num_dai component in searching dai name
+    - media: imx-jpeg: fix a bug of accessing array out of bounds
+    - media: cx88-mpeg: clear interrupt status register before streaming video
+    - uaccess: fix type mismatch warnings from access_ok()
+    - lib/test_lockup: fix kernel pointer check for separate address spaces
+    - ARM: tegra: tamonten: Fix I2C3 pad setting
+    - ARM: mmp: Fix failure to remove sram device
+    - ASoC: amd: vg: fix for pm resume callback sequence
+    - video: fbdev: sm712fb: Fix crash in smtcfb_write()
+    - media: i2c: ov5648: Fix lockdep error
+    - media: Revert "media: em28xx: add missing em28xx_close_extension"
+    - media: hdpvr: initialize dev->worker at hdpvr_register_videodev
+    - ASoC: Intel: sof_sdw: fix quirks for 2022 HP Spectre x360 13"
+    - tracing: Have TRACE_DEFINE_ENUM affect trace event types as well
+    - mmc: host: Return an error when ->enable_sdio_irq() ops is missing
+    - media: atomisp: fix bad usage at error handling logic
+    - ALSA: hda/realtek: Add alc256-samsung-headphone fixup
+    - KVM: x86: Reinitialize context if host userspace toggles EFER.LME
+    - KVM: x86/mmu: Move "invalid" check out of kvm_tdp_mmu_get_root()
+    - KVM: x86/mmu: Zap _all_ roots when unmapping gfn range in TDP MMU
+    - KVM: x86/mmu: Check for present SPTE when clearing dirty bit in TDP MMU
+    - KVM: x86: hyper-v: Drop redundant 'ex' parameter from kvm_hv_send_ipi()
+    - KVM: x86: hyper-v: Drop redundant 'ex' parameter from kvm_hv_flush_tlb()
+    - KVM: x86: hyper-v: Fix the maximum number of sparse banks for XMM fast TLB
+      flush hypercalls
+    - KVM: x86: hyper-v: HVCALL_SEND_IPI_EX is an XMM fast hypercall
+    - powerpc/kasan: Fix early region not updated correctly
+    - powerpc/lib/sstep: Fix 'sthcx' instruction
+    - powerpc/lib/sstep: Fix build errors with newer binutils
+    - powerpc: Add set_memory_{p/np}() and remove set_memory_attr()
+    - powerpc: Fix build errors with newer binutils
+    - drm/dp: Fix off-by-one in register cache size
+    - drm/i915: Treat SAGV block time 0 as SAGV disabled
+    - drm/i915: Fix PSF GV point mask when SAGV is not possible
+    - drm/i915: Reject unsupported TMDS rates on ICL+
+    - scsi: qla2xxx: Refactor asynchronous command initialization
+    - scsi: qla2xxx: Implement ref count for SRB
+    - scsi: qla2xxx: Fix stuck session in gpdb
+    - scsi: qla2xxx: Fix warning message due to adisc being flushed
+    - scsi: qla2xxx: Fix scheduling while atomic
+    - scsi: qla2xxx: Fix premature hw access after PCI error
+    - scsi: qla2xxx: Fix wrong FDMI data for 64G adapter
+    - scsi: qla2xxx: Fix warning for missing error code
+    - scsi: qla2xxx: Fix device reconnect in loop topology
+    - scsi: qla2xxx: edif: Fix clang warning
+    - scsi: qla2xxx: Fix T10 PI tag escape and IP guard options for 28XX adapters
+    - scsi: qla2xxx: Add devids and conditionals for 28xx
+    - scsi: qla2xxx: Check for firmware dump already collected
+    - scsi: qla2xxx: Suppress a kernel complaint in qla_create_qpair()
+    - scsi: qla2xxx: Fix disk failure to rediscover
+    - scsi: qla2xxx: Fix incorrect reporting of task management failure
+    - scsi: qla2xxx: Fix hang due to session stuck
+    - scsi: qla2xxx: Fix missed DMA unmap for NVMe ls requests
+    - scsi: qla2xxx: Fix N2N inconsistent PLOGI
+    - scsi: qla2xxx: Fix stuck session of PRLI reject
+    - scsi: qla2xxx: Reduce false trigger to login
+    - scsi: qla2xxx: Use correct feature type field during RFF_ID processing
+    - platform: chrome: Split trace include file
+    - KVM: x86: Check lapic_in_kernel() before attempting to set a SynIC irq
+    - KVM: x86: Avoid theoretical NULL pointer dereference in
+      kvm_irq_delivery_to_apic_fast()
+    - KVM: x86: Forbid VMM to set SYNIC/STIMER MSRs when SynIC wasn't activated
+    - KVM: Prevent module exit until all VMs are freed
+    - KVM: x86: fix sending PV IPI
+    - KVM: SVM: fix panic on out-of-bounds guest IRQ
+    - ubifs: rename_whiteout: Fix double free for whiteout_ui->data
+    - ubifs: Fix deadlock in concurrent rename whiteout and inode writeback
+    - ubifs: Add missing iput if do_tmpfile() failed in rename whiteout
+    - ubifs: Rename whiteout atomically
+    - ubifs: Fix 'ui->dirty' race between do_tmpfile() and writeback work
+    - ubifs: Rectify space amount budget for mkdir/tmpfile operations
+    - ubifs: setflags: Make dirtied_ino_d 8 bytes aligned
+    - ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock()
+    - ubifs: Fix to add refcount once page is set private
+    - ubifs: rename_whiteout: correct old_dir size computing
+    - nvme: allow duplicate NSIDs for private namespaces
+    - nvme: fix the read-only state for zoned namespaces with unsupposed features
+    - wireguard: queueing: use CFI-safe ptr_ring cleanup function
+    - wireguard: socket: free skb in send6 when ipv6 is disabled
+    - wireguard: socket: ignore v6 endpoints when ipv6 is disabled
+    - XArray: Fix xas_create_range() when multi-order entry present
+    - can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path
+    - can: mcba_usb: properly check endpoint type
+    - can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix return of error value
+    - XArray: Update the LRU list in xas_split()
+    - modpost: restore the warning message for missing symbol versions
+    - rtc: check if __rtc_read_time was successful
+    - gfs2: gfs2_setattr_size error path fix
+    - gfs2: Make sure FITRIM minlen is rounded up to fs block size
+    - net: hns3: fix the concurrency between functions reading debugfs
+    - net: hns3: fix software vlan talbe of vlan 0 inconsistent with hardware
+    - rxrpc: fix some null-ptr-deref bugs in server_key.c
+    - rxrpc: Fix call timer start racing with call destruction
+    - mailbox: imx: fix wakeup failure from freeze mode
+    - crypto: arm/aes-neonbs-cbc - Select generic cbc and aes
+    - watch_queue: Free the page array when watch_queue is dismantled
+    - pinctrl: pinconf-generic: Print arguments for bias-pull-*
+    - watchdog: rti-wdt: Add missing pm_runtime_disable() in probe function
+    - net: sparx5: uses, depends on BRIDGE or !BRIDGE
+    - pinctrl: nuvoton: npcm7xx: Rename DS() macro to DSTR()
+    - pinctrl: nuvoton: npcm7xx: Use %zu printk format for ARRAY_SIZE()
+    - ASoC: mediatek: mt6358: add missing EXPORT_SYMBOLs
+    - ubi: Fix race condition between ctrl_cdev_ioctl and ubi_cdev_ioctl
+    - ARM: iop32x: offset IRQ numbers by 1
+    - block: Fix the maximum minor value is blk_alloc_ext_minor()
+    - io_uring: fix memory leak of uid in files registration
+    - riscv module: remove (NOLOAD)
+    - ACPI: CPPC: Avoid out of bounds access when parsing _CPC data
+    - vhost: handle error while adding split ranges to iotlb
+    - spi: Fix Tegra QSPI example
+    - platform/chrome: cros_ec_typec: Check for EC device
+    - can: isotp: restore accidentally removed MSG_PEEK feature
+    - proc: bootconfig: Add null pointer check
+    - drm/connector: Fix typo in documentation
+    - scsi: qla2xxx: Add qla2x00_async_done() for async routines
+    - staging: mt7621-dts: fix pinctrl-0 items to be size-1 items on ethernet
+    - arm64: mm: Drop 'const' from conditional arm64_dma_phys_limit definition
+    - ASoC: soc-compress: Change the check for codec_dai
+    - Reinstate some of "swiotlb: rework "fix info leak with DMA_FROM_DEVICE""
+    - tracing: Have type enum modifications copy the strings
+    - net: add skb_set_end_offset() helper
+    - net: preserve skb_end_offset() in skb_unclone_keeptruesize()
+    - mm/mmap: return 1 from stack_guard_gap __setup() handler
+    - ARM: 9187/1: JIVE: fix return value of __setup handler
+    - mm/memcontrol: return 1 from cgroup.memory __setup() handler
+    - mm/usercopy: return 1 from hardened_usercopy __setup() handler
+    - af_unix: Support POLLPRI for OOB.
+    - bpf: Adjust BPF stack helper functions to accommodate skip > 0
+    - bpf: Fix comment for helper bpf_current_task_under_cgroup()
+    - mmc: rtsx: Use pm_runtime_{get,put}() to handle runtime PM
+    - dt-bindings: mtd: nand-controller: Fix the reg property description
+    - dt-bindings: mtd: nand-controller: Fix a comment in the examples
+    - dt-bindings: spi: mxic: The interrupt property is not mandatory
+    - dt-bindings: memory: mtk-smi: No need mediatek,larb-id for mt8167
+    - dt-bindings: pinctrl: pinctrl-microchip-sgpio: Fix example
+    - ubi: fastmap: Return error code if memory allocation fails in add_aeb()
+    - ASoC: SOF: Intel: Fix build error without SND_SOC_SOF_PCI_DEV
+    - ASoC: topology: Allow TLV control to be either read or write
+    - perf vendor events: Update metrics for SkyLake Server
+    - media: ov6650: Add try support to selection API operations
+    - media: ov6650: Fix crop rectangle affected by set format
+    - spi: mediatek: support tick_delay without enhance_timing
+    - ARM: dts: spear1340: Update serial node properties
+    - ARM: dts: spear13xx: Update SPI dma properties
+    - arm64: dts: ls1043a: Update i2c dma properties
+    - arm64: dts: ls1046a: Update i2c node dma properties
+    - um: Fix uml_mconsole stop/go
+    - docs: sysctl/kernel: add missing bit to panic_print
+    - openvswitch: Fixed nd target mask field in the flow dump.
+    - torture: Make torture.sh help message match reality
+    - n64cart: convert bi_disk to bi_bdev->bd_disk fix build
+    - mmc: rtsx: Let MMC core handle runtime PM
+    - mmc: rtsx: Fix build errors/warnings for unused variable
+    - KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
+    - iommu/dma: Skip extra sync during unmap w/swiotlb
+    - iommu/dma: Fold _swiotlb helpers into callers
+    - iommu/dma: Check CONFIG_SWIOTLB more broadly
+    - swiotlb: Support aligned swiotlb buffers
+    - iommu/dma: Account for min_align_mask w/swiotlb
+    - coredump: Snapshot the vmas in do_coredump
+    - coredump: Remove the WARN_ON in dump_vma_snapshot
+    - coredump/elf: Pass coredump_params into fill_note_info
+    - coredump: Use the vma snapshot in fill_files_note
+    - PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
+    - Linux 5.15.33
+  * Jammy update: v5.15.32 upstream stable release (LP: #1969106)
+    - net: ipv6: fix skb_over_panic in __ip6_append_data
+    - tpm: Fix error handling in async work
+    - Bluetooth: btusb: Add another Realtek 8761BU
+    - llc: fix netdevice reference leaks in llc_ui_bind()
+    - ASoC: sti: Fix deadlock via snd_pcm_stop_xrun() call
+    - ALSA: oss: Fix PCM OSS buffer allocation overflow
+    - ALSA: usb-audio: add mapping for new Corsair Virtuoso SE
+    - ALSA: hda/realtek: Add quirk for Clevo NP70PNJ
+    - ALSA: hda/realtek: Add quirk for Clevo NP50PNJ
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
+    - ALSA: hda/realtek: Add quirk for ASUS GA402
+    - ALSA: pcm: Fix races among concurrent hw_params and hw_free calls
+    - ALSA: pcm: Fix races among concurrent read/write and buffer changes
+    - ALSA: pcm: Fix races among concurrent prepare and hw_params/hw_free calls
+    - ALSA: pcm: Fix races among concurrent prealloc proc writes
+    - ALSA: pcm: Add stream lock during PCM reset ioctl operations
+    - ALSA: usb-audio: Add mute TLV for playback volumes on RODE NT-USB
+    - ALSA: cmipci: Restore aux vol on suspend/resume
+    - ALSA: pci: fix reading of swapped values from pcmreg in AC97 codec
+    - drivers: net: xgene: Fix regression in CRC stripping
+    - ACPI / x86: Work around broken XSDT on Advantech DAC-BJ01 board
+    - ACPI: battery: Add device HID and quirk for Microsoft Surface Go 3
+    - ACPI: video: Force backlight native for Clevo NL5xRU and NL5xNU
+    - crypto: qat - disable registration of algorithms
+    - Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
+    - Revert "ath: add support for special 0x0 regulatory domain"
+    - drm/virtio: Ensure that objs is not NULL in virtio_gpu_array_put_free()
+    - rcu: Don't deboost before reporting expedited quiescent state
+    - uaccess: fix integer overflow on access_ok()
+    - mac80211: fix potential double free on mesh join
+    - tpm: use try_get_ops() in tpm-space.c
+    - wcn36xx: Differentiate wcn3660 from wcn3620
+    - m68k: fix access_ok for coldfire
+    - nds32: fix access_ok() checks in get/put_user
+    - llc: only change llc->dev when bind() succeeds
+    - Linux 5.15.32
+  * Jammy update: v5.15.31 upstream stable release (LP: #1969105)
+    - crypto: qcom-rng - ensure buffer for generate is completely filled
+    - ocfs2: fix crash when initialize filecheck kobj fails
+    - mm: swap: get rid of livelock in swapin readahead
+    - block: release rq qos structures for queue without disk
+    - drm/mgag200: Fix PLL setup for g200wb and g200ew
+    - efi: fix return value of __setup handlers
+    - alx: acquire mutex for alx_reinit in alx_change_mtu
+    - vsock: each transport cycles only on its own sockets
+    - esp6: fix check on ipv6_skip_exthdr's return value
+    - net: phy: marvell: Fix invalid comparison in the resume and suspend
+      functions
+    - net/packet: fix slab-out-of-bounds access in packet_recvmsg()
+    - atm: eni: Add check for dma_map_single
+    - iavf: Fix double free in iavf_reset_task
+    - hv_netvsc: Add check for kvmalloc_array
+    - drm/imx: parallel-display: Remove bus flags check in
+      imx_pd_bridge_atomic_check()
+    - drm/panel: simple: Fix Innolux G070Y2-L01 BPP settings
+    - net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
+    - drm: Don't make DRM_PANEL_BRIDGE dependent on DRM_KMS_HELPERS
+    - net: dsa: Add missing of_node_put() in dsa_port_parse_of
+    - net: phy: mscc: Add MODULE_FIRMWARE macros
+    - bnx2x: fix built-in kernel driver load failure
+    - net: bcmgenet: skip invalid partial checksums
+    - net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower
+      offload
+    - iavf: Fix hang during reboot/shutdown
+    - arm64: fix clang warning about TRAMP_VALIAS
+    - usb: gadget: rndis: prevent integer overflow in rndis_set_response()
+    - usb: gadget: Fix use-after-free bug by not setting udc->dev.driver
+    - usb: usbtmc: Fix bug in pipe direction for control transfers
+    - scsi: mpt3sas: Page fault in reply q processing
+    - Input: aiptek - properly check endpoint type
+    - perf symbols: Fix symbol size calculation condition
+    - btrfs: skip reserved bytes warning on unmount after log cleanup failure
+    - Linux 5.15.31
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 29 Jul 2022 09:57:21 +1000
+
+linux-xilinx-zynqmp (5.15.0-1011.12) jammy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enable imx219 kernel module
+
+  * Miscellaneous upstream changes
+    - xilinx: Enable imx219 for SOM rpi apps
+    - drm: xlnx: zynqmp_dp: Fix kernel dump messages when the DP cable is
+      disconnected
+    - staging: xilinx-tsn: initialize timer_priv struct in axienet_local
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 16 Jun 2022 09:20:28 +1000
+
+linux-xilinx-zynqmp (5.15.0-1010.11) jammy; urgency=medium
+
+  * Miscellaneous upstream changes
+    - net: macb: Use device_link framework to specify suspend/resume dependency
+    - arm64: zynqmp: Add linux,code for fwuen button
+    - usb: dwc3: xilinx: Fix error handling when getting USB3 PHY
+    - usb: dwc3: Added remote wake-up in xilinx glue driver
+    - usb: xhci-plat: Add remote wakeup support for xilinx
+    - usb: dwc3: xilinx: fix usb3 non-wakeup source resume failure
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Tue, 07 Jun 2022 20:36:56 +0800
+
+linux-xilinx-zynqmp (5.15.0-1009.10) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * INVALID or PRIVATE BUG (LP: #1975694)
+    - Enable Xilinx mv-camera-10gige-module kernel module
+    - [Config] Enable xilinx-mv-camera-10gige-module
+
+  * INVALID or PRIVATE BUG (LP: #1975695)
+    - Enable Xilinx mv-camera-sensor-module kernel module
+
+  [ Ubuntu: 5.15.0-33.34 ]
+
+  * jammy/linux: 5.15.0-33.34 -proposed tracker (LP: #1973924)
+  * CVE-2022-29581
+    - net/sched: cls_u32: fix netns refcount changes in u32_change()
+  * ext4: limit length to bitmap_maxbytes (LP: #1972281)
+    - ext4: limit length to bitmap_maxbytes - blocksize in punch_hole
+  * Unprivileged users may use PTRACE_SEIZE to set PTRACE_O_SUSPEND_SECCOMP
+    option (LP: #1972740)
+    - ptrace: Check PTRACE_O_SUSPEND_SECCOMP permission on PTRACE_SEIZE
+
+  [ Ubuntu: 5.15.0-30.31 ]
+
+  * jammy/linux: 5.15.0-30.31 -proposed tracker (LP: #1971685)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2022.04.18)
+  * Intel: enable x86 AMX (LP: #1967750)
+    - x86/extable: Tidy up redundant handler functions
+    - x86/extable: Get rid of redundant macros
+    - x86/mce: Deduplicate exception handling
+    - x86/mce: Get rid of stray semicolons
+    - x86/extable: Rework the exception table mechanics
+    - x86/extable: Provide EX_TYPE_DEFAULT_MCE_SAFE and EX_TYPE_FAULT_MCE_SAFE
+    - x86/copy_mc: Use EX_TYPE_DEFAULT_MCE_SAFE for exception fixups
+    - x86/fpu: Use EX_TYPE_FAULT_MCE_SAFE for exception fixups
+    - x86/extable: Remove EX_TYPE_FAULT from MCE safe fixups
+    - x86/fpu/signal: Clarify exception handling in restore_fpregs_from_user()
+    - x86/fpu/signal: Move header zeroing out of xsave_to_user_sigframe()
+    - x86/fpu/signal: Move xstate clearing out of copy_fpregs_to_sigframe()
+    - x86/fpu/signal: Change return type of copy_fpstate_to_sigframe() to boolean
+    - x86/fpu/signal: Change return type of copy_fpregs_to_sigframe() helpers to
+      boolean
+    - x86/signal: Change return type of restore_sigcontext() to boolean
+    - x86/fpu/signal: Change return type of fpu__restore_sig() to boolean
+    - x86/fpu/signal: Change return type of __fpu_restore_sig() to boolean
+    - x86/fpu/signal: Change return code of check_xstate_in_sigframe() to boolean
+    - x86/fpu/signal: Change return code of restore_fpregs_from_user() to boolean
+    - x86/fpu/signal: Fix missed conversion to correct boolean retval in
+      save_xstate_epilog()
+    - x86/fpu: Remove pointless argument from switch_fpu_finish()
+    - x86/fpu: Update stale comments
+    - x86/pkru: Remove useless include
+    - x86/fpu: Restrict xsaves()/xrstors() to independent states
+    - x86/fpu: Cleanup the on_boot_cpu clutter
+    - x86/fpu: Remove pointless memset in fpu_clone()
+    - x86/process: Clone FPU in copy_thread()
+    - x86/fpu: Do not inherit FPU context for kernel and IO worker threads
+    - x86/fpu: Cleanup xstate xcomp_bv initialization
+    - x86/fpu/xstate: Provide and use for_each_xfeature()
+    - x86/fpu/xstate: Mark all init only functions __init
+    - x86/fpu: Move KVMs FPU swapping to FPU core
+    - x86/fpu: Replace KVMs home brewed FPU copy from user
+    - x86/fpu: Rework copy_xstate_to_uabi_buf()
+    - x86/fpu: Mark fpu__init_prepare_fx_sw_frame() as __init
+    - x86/fpu: Move context switch and exit to user inlines into sched.h
+    - x86/fpu: Clean up CPU feature tests
+    - x86/fpu: Make os_xrstor_booting() private
+    - x86/fpu: Move os_xsave() and os_xrstor() to core
+    - x86/fpu: Move legacy ASM wrappers to core
+    - x86/fpu: Make WARN_ON_FPU() private
+    - x86/fpu: Move fpregs_restore_userregs() to core
+    - x86/fpu: Move mxcsr related code to core
+    - x86/fpu: Move fpstate functions to api.h
+    - x86/fpu: Remove internal.h dependency from fpu/signal.h
+    - x86/sev: Include fpu/xcr.h
+    - x86/fpu: Mop up the internal.h leftovers
+    - x86/fpu: Replace the includes of fpu/internal.h
+    - x86/fpu: Provide a proper function for ex_handler_fprestore()
+    - x86/fpu: Replace KVMs home brewed FPU copy to user
+    - x86/fpu: Provide struct fpstate
+    - x86/fpu: Convert fpstate_init() to struct fpstate
+    - x86/fpu: Convert restore_fpregs_from_fpstate() to struct fpstate
+    - x86/fpu: Replace KVMs xstate component clearing
+    - x86/KVM: Convert to fpstate
+    - x86/fpu: Convert tracing to fpstate
+    - x86/fpu/regset: Convert to fpstate
+    - x86/fpu/signal: Convert to fpstate
+    - x86/fpu/core: Convert to fpstate
+    - x86/math-emu: Convert to fpstate
+    - x86/fpu: Remove fpu::state
+    - x86/fpu: Do not leak fpstate pointer on fork
+    - x86/process: Move arch_thread_struct_whitelist() out of line
+    - x86/fpu: Add size and mask information to fpstate
+    - x86/fpu: Use fpstate::size
+    - x86/fpu/xstate: Use fpstate for os_xsave()
+    - x86/fpu/xstate: Use fpstate for xsave_to_user_sigframe()
+    - x86/fpu: Use fpstate in fpu_copy_kvm_uabi_to_fpstate()
+    - x86/fpu: Use fpstate in __copy_xstate_to_uabi_buf()
+    - x86/fpu/xstate: Use fpstate for copy_uabi_to_xstate()
+    - x86/fpu/signal: Use fpstate for size and features
+    - x86/fpu: Provide struct fpu_config
+    - x86/fpu: Cleanup fpu__init_system_xstate_size_legacy()
+    - x86/fpu/xstate: Cleanup size calculations
+    - x86/fpu: Move xstate size to fpu_*_cfg
+    - x86/fpu: Move xstate feature masks to fpu_*_cfg
+    - x86/fpu: Mop up xfeatures_mask_uabi()
+    - x86/fpu: Rework restore_regs_from_fpstate()
+    - x86/fpu/xstate: Move remaining xfeature helpers to core
+    - x86/fpu: Prepare for sanitizing KVM FPU code
+    - x86/fpu: Provide infrastructure for KVM FPU cleanup
+    - x86/kvm: Convert FPU handling to a single swap buffer
+    - x86/fpu: Remove old KVM FPU interface
+    - signal: Add an optional check for altstack size
+    - x86/signal: Implement sigaltstack size validation
+    - x86/fpu/xstate: Provide xstate_calculate_size()
+    - x86/fpu: Add members to struct fpu to cache permission information
+    - x86/fpu: Add fpu_state_config::legacy_features
+    - x86/arch_prctl: Add controls for dynamic XSTATE components
+    - x86/fpu: Add basic helpers for dynamically enabled features
+    - x86/signal: Use fpu::__state_user_size for sigalt stack validation
+    - x86/fpu/signal: Prepare for variable sigframe length
+    - x86/fpu: Prepare fpu_clone() for dynamically enabled features
+    - x86/fpu: Reset permission and fpstate on exec()
+    - x86/cpufeatures: Add eXtended Feature Disabling (XFD) feature bit
+    - x86/msr-index: Add MSRs for XFD
+    - x86/fpu: Add XFD state to fpstate
+    - x86/fpu: Add sanity checks for XFD
+    - x86/fpu: Update XFD state where required
+    - x86/fpu/xstate: Add XFD #NM handler
+    - x86/fpu/xstate: Add fpstate_realloc()/free()
+    - x86/fpu/xstate: Prepare XSAVE feature table for gaps in state component
+      numbers
+    - x86/fpu/amx: Define AMX state components and have it used for boot-time
+      checks
+    - x86/fpu: Calculate the default sizes independently
+    - x86/fpu: Add XFD handling for dynamic states
+    - x86/fpu/amx: Enable the AMX feature in 64-bit mode
+    - selftests/x86/amx: Add test cases for AMX state management
+    - selftests/x86/amx: Add context switch test
+    - Documentation/x86: Add documentation for using dynamic XSTATE features
+    - x86/fpu/signal: Initialize sw_bytes in save_xstate_epilog()
+    - signal: Skip the altstack update when not needed
+    - x86/cpufeatures: Put the AMX macros in the word 18 block
+    - x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
+    - selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
+    - [Config] updateconfigs after AMX patchset
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Mon, 06 Jun 2022 11:41:00 +1000
+
+linux-xilinx-zynqmp (5.15.0-1008.9) jammy; urgency=medium
+
+  * Miscellaneous upstream changes
+    - mtd: spi-nor: For erase size equal to 0 set erase size_shift to 0
+    - xilinx-ams: Fix UBSan Warning
+    - net: macb: Fix ethtool WOL helper
+    - dt-bindings: fpga: Add property "resets" to xilinx-afi driver
+    - fpga: Add ps-pl reset handling through xilinx afi driver
+    - staging: xilinx-tsn: Fix axienet_tsn ioctl
+    - staging: xilinx-tsn: Add ethtool hook to read phc associated with ep
+    - staging: xilinx-tsn: Remove hardcoded interface names
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Thu, 26 May 2022 21:43:48 +0800
+
+linux-xilinx-zynqmp (5.15.0-1007.8) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1966941) // INVALID or PRIVATE BUG
+    (LP: #1968270)
+    - [Config] Disable CONFIG_UBSAN
+
+  * INVALID or PRIVATE BUG (LP: #1970466)
+    - [Config] Enable fancontrol
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Sat, 07 May 2022 19:26:24 +0800
+
+linux-xilinx-zynqmp (5.15.0-1006.7) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1967068)
+    - arm64: dts: zynqmp: Add is-dual for qspi
+    - [Config] Disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
+
+  * INVALID or PRIVATE BUG (LP: #1968978)
+    - [Config] Update configs for TSN
+
+  * Miscellaneous upstream changes
+    - Import Xilinx VCU kernel modules
+    - Enable VCU kernel modules as default
+    - Disable CONFIG_VIDEO_ALLEGRO_DVT
+    - Enable Xilinx HDMI kernel modules
+    - Fix build error for HDMI kernel modules
+    - Import XRT 2022.1 kernel modules
+    - Add DRM_ZOCL option for XRT driver
+
+  [ Ubuntu: 5.15.0-27.28 ]
+
+  * jammy/linux: 5.15.0-27.28 -proposed tracker (LP: #1968954)
+
+  [ Ubuntu: 5.15.0-26.27 ]
+
+  * jammy/linux: 5.15.0-26.27 -proposed tracker (LP: #1968850)
+  * CVE-2022-1016
+    - netfilter: nf_tables: initialize registers in nft_do_chain()
+  * CVE-2022-1015
+    - netfilter: nf_tables: validate registers coming from userspace.
+  * CVE-2022-26490
+    - nfc: st21nfca: Fix potential buffer overflows in EVT_TRANSACTION
+  * harden indirect calls against BHI attacks (LP: #1967579)
+    - objtool: Classify symbols
+    - objtool: Explicitly avoid self modifying code in .altinstr_replacement
+    - objtool: Shrink struct instruction
+    - objtool,x86: Replace alternatives with .retpoline_sites
+    - x86/retpoline: Remove unused replacement symbols
+    - x86/asm: Fix register order
+    - x86/asm: Fixup odd GEN-for-each-reg.h usage
+    - x86/retpoline: Move the retpoline thunk declarations to nospec-branch.h
+    - x86/retpoline: Create a retpoline thunk array
+    - x86/alternative: Implement .retpoline_sites support
+    - x86/alternative: Handle Jcc __x86_indirect_thunk_\reg
+    - x86/alternative: Try inline spectre_v2=retpoline,amd
+    - x86/alternative: Add debug prints to apply_retpolines()
+    - bpf,x86: Simplify computing label offsets
+    - bpf,x86: Respect X86_FEATURE_RETPOLINE*
+
+  [ Ubuntu: 5.15.0-25.25 ]
+
+  * jammy/linux: 5.15.0-25.25 -proposed tracker (LP: #1967146)
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "scsi: core: Reallocate device's budget map on queue depth
+      change"
+
+  [ Ubuntu: 5.15.0-24.24 ]
+
+  * jammy/linux: 5.15.0-24.24 -proposed tracker (LP: #1966305)
+  * Update OS policy capability handshake (LP: #1966089)
+    - thermal: int340x: Update OS policy capability handshake
+  * Jammy update: v5.15.30 upstream stable release (LP: #1966057)
+    - Revert "xfrm: state and policy should fail if XFRMA_IF_ID 0"
+    - arm64: dts: rockchip: fix rk3399-puma-haikou USB OTG mode
+    - xfrm: Check if_id in xfrm_migrate
+    - xfrm: Fix xfrm migrate issues when address family changes
+    - arm64: dts: rockchip: fix rk3399-puma eMMC HS400 signal integrity
+    - arm64: dts: rockchip: align pl330 node name with dtschema
+    - arm64: dts: rockchip: reorder rk3399 hdmi clocks
+    - arm64: dts: agilex: use the compatible "intel,socfpga-agilex-hsotg"
+    - ARM: dts: rockchip: reorder rk322x hmdi clocks
+    - ARM: dts: rockchip: fix a typo on rk3288 crypto-controller
+    - mac80211: refuse aggregations sessions before authorized
+    - MIPS: smp: fill in sibling and core maps earlier
+    - ARM: 9178/1: fix unmet dependency on BITREVERSE for HAVE_ARCH_BITREVERSE
+    - Bluetooth: hci_core: Fix leaking sent_cmd skb
+    - can: rcar_canfd: rcar_canfd_channel_probe(): register the CAN device when
+      fully ready
+    - atm: firestream: check the return value of ioremap() in fs_init()
+    - iwlwifi: don't advertise TWT support
+    - drm/vrr: Set VRR capable prop only if it is attached to connector
+    - nl80211: Update bss channel on channel switch for P2P_CLIENT
+    - tcp: make tcp_read_sock() more robust
+    - sfc: extend the locking on mcdi->seqno
+    - bnx2: Fix an error message
+    - kselftest/vm: fix tests build with old libc
+    - x86/module: Fix the paravirt vs alternative order
+    - ice: Fix race condition during interface enslave
+    - Linux 5.15.30
+  * Jammy update: v5.15.29 upstream stable release (LP: #1966056)
+    - arm64: dts: qcom: sm8350: Describe GCC dependency clocks
+    - arm64: dts: qcom: sm8350: Correct UFS symbol clocks
+    - HID: elo: Revert USB reference counting
+    - HID: hid-thrustmaster: fix OOB read in thrustmaster_interrupts
+    - ARM: boot: dts: bcm2711: Fix HVS register range
+    - clk: qcom: gdsc: Add support to update GDSC transition delay
+    - clk: qcom: dispcc: Update the transition delay for MDSS GDSC
+    - HID: vivaldi: fix sysfs attributes leak
+    - arm64: dts: armada-3720-turris-mox: Add missing ethernet0 alias
+    - tipc: fix kernel panic when enabling bearer
+    - vdpa/mlx5: add validation for VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET command
+    - vduse: Fix returning wrong type in vduse_domain_alloc_iova()
+    - net: phy: meson-gxl: fix interrupt handling in forced mode
+    - mISDN: Fix memory leak in dsp_pipeline_build()
+    - vhost: fix hung thread due to erroneous iotlb entries
+    - virtio-blk: Don't use MAX_DISCARD_SEGMENTS if max_discard_seg is zero
+    - vdpa: fix use-after-free on vp_vdpa_remove
+    - isdn: hfcpci: check the return value of dma_set_mask() in setup_hw()
+    - net: qlogic: check the return value of dma_alloc_coherent() in
+      qed_vf_hw_prepare()
+    - esp: Fix possible buffer overflow in ESP transformation
+    - esp: Fix BEET mode inter address family tunneling on GSO
+    - qed: return status of qed_iov_get_link
+    - smsc95xx: Ignore -ENODEV errors when device is unplugged
+    - gpiolib: acpi: Convert ACPI value of debounce to microseconds
+    - drm/sun4i: mixer: Fix P010 and P210 format numbers
+    - net: dsa: mt7530: fix incorrect test in mt753x_phylink_validate()
+    - ARM: dts: aspeed: Fix AST2600 quad spi group
+    - iavf: Fix handling of vlan strip virtual channel messages
+    - i40e: stop disabling VFs due to PF error responses
+    - ice: stop disabling VFs due to PF error responses
+    - ice: Fix error with handling of bonding MTU
+    - ice: Don't use GFP_KERNEL in atomic context
+    - ice: Fix curr_link_speed advertised speed
+    - ethernet: Fix error handling in xemaclite_of_probe
+    - tipc: fix incorrect order of state message data sanity check
+    - net: ethernet: ti: cpts: Handle error for clk_enable
+    - net: ethernet: lpc_eth: Handle error for clk_enable
+    - net: marvell: prestera: Add missing of_node_put() in
+      prestera_switch_set_base_mac_addr
+    - ax25: Fix NULL pointer dereference in ax25_kill_by_device
+    - net/mlx5: Fix size field in bufferx_reg struct
+    - net/mlx5: Fix a race on command flush flow
+    - net/mlx5e: Lag, Only handle events from highest priority multipath entry
+    - NFC: port100: fix use-after-free in port100_send_complete
+    - selftests: pmtu.sh: Kill tcpdump processes launched by subshell.
+    - selftests: pmtu.sh: Kill nettest processes launched in subshell.
+    - gpio: ts4900: Do not set DAT and OE together
+    - gianfar: ethtool: Fix refcount leak in gfar_get_ts_info
+    - net: phy: DP83822: clear MISR2 register to disable interrupts
+    - sctp: fix kernel-infoleak for SCTP sockets
+    - net: bcmgenet: Don't claim WOL when its not available
+    - net: phy: meson-gxl: improve link-up behavior
+    - selftests/bpf: Add test for bpf_timer overwriting crash
+    - swiotlb: fix info leak with DMA_FROM_DEVICE
+    - usb: dwc3: pci: add support for the Intel Raptor Lake-S
+    - pinctrl: tigerlake: Revert "Add Alder Lake-M ACPI ID"
+    - KVM: Fix lockdep false negative during host resume
+    - kvm: x86: Disable KVM_HC_CLOCK_PAIRING if tsc is in always catchup mode
+    - spi: rockchip: Fix error in getting num-cs property
+    - spi: rockchip: terminate dma transmission when slave abort
+    - drm/vc4: hdmi: Unregister codec device on unbind
+    - x86/kvm: Don't use pv tlb/ipi/sched_yield if on 1 vCPU
+    - net-sysfs: add check for netdevice being present to speed_show
+    - hwmon: (pmbus) Clear pmbus fault/warning bits after read
+    - PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
+    - gpio: Return EPROBE_DEFER if gc->to_irq is NULL
+    - drm/amdgpu: bypass tiling flag check in virtual display case (v2)
+    - Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
+    - Revert "xen-netback: Check for hotplug-status existence before watching"
+    - ipv6: prevent a possible race condition with lifetimes
+    - tracing: Ensure trace buffer is at least 4096 bytes large
+    - tracing/osnoise: Make osnoise_main to sleep for microseconds
+    - selftest/vm: fix map_fixed_noreplace test failure
+    - selftests/memfd: clean up mapping in mfd_fail_write
+    - ARM: Spectre-BHB: provide empty stub for non-config
+    - fuse: fix fileattr op failure
+    - fuse: fix pipe buffer lifetime for direct_io
+    - staging: rtl8723bs: Fix access-point mode deadlock
+    - staging: gdm724x: fix use after free in gdm_lte_rx()
+    - net: macb: Fix lost RX packet wakeup race in NAPI receive
+    - riscv: alternative only works on !XIP_KERNEL
+    - mmc: meson: Fix usage of meson_mmc_post_req()
+    - riscv: Fix auipc+jalr relocation range checks
+    - tracing/osnoise: Force quiescent states while tracing
+    - arm64: dts: marvell: armada-37xx: Remap IO space to bus address 0x0
+    - arm64: Ensure execute-only permissions are not allowed without EPAN
+    - arm64: kasan: fix include error in MTE functions
+    - swiotlb: rework "fix info leak with DMA_FROM_DEVICE"
+    - KVM: x86/mmu: kvm_faultin_pfn has to return false if pfh is returned
+    - virtio: unexport virtio_finalize_features
+    - virtio: acknowledge all features before access
+    - net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
+    - ARM: fix Thumb2 regression with Spectre BHB
+    - watch_queue: Fix filter limit check
+    - watch_queue, pipe: Free watchqueue state after clearing pipe ring
+    - watch_queue: Fix to release page in ->release()
+    - watch_queue: Fix to always request a pow-of-2 pipe ring size
+    - watch_queue: Fix the alloc bitmap size to reflect notes allocated
+    - watch_queue: Free the alloc bitmap when the watch_queue is torn down
+    - watch_queue: Fix lack of barrier/sync/lock between post and read
+    - watch_queue: Make comment about setting ->defunct more accurate
+    - x86/boot: Fix memremap of setup_indirect structures
+    - x86/boot: Add setup_indirect support in early_memremap_is_setup_data()
+    - x86/sgx: Free backing memory after faulting the enclave page
+    - x86/traps: Mark do_int3() NOKPROBE_SYMBOL
+    - drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP
+    - btrfs: make send work with concurrent block group relocation
+    - drm/i915: Workaround broken BIOS DBUF configuration on TGL/RKL
+    - riscv: dts: k210: fix broken IRQs on hart1
+    - block: drop unused includes in <linux/genhd.h>
+    - Revert "net: dsa: mv88e6xxx: flush switchdev FDB workqueue before removing
+      VLAN"
+    - vhost: allow batching hint without size
+    - Linux 5.15.29
+  * Jammy update: v5.15.28 upstream stable release (LP: #1966055)
+    - slip: fix macro redefine warning
+    - ARM: fix co-processor register typo
+    - ARM: Do not use NOCROSSREFS directive with ld.lld
+    - arm64: Do not include __READ_ONCE() block in assembly files
+    - ARM: fix build warning in proc-v7-bugs.c
+    - xen/xenbus: don't let xenbus_grant_ring() remove grants in error case
+    - xen/grant-table: add gnttab_try_end_foreign_access()
+    - xen/blkfront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/netfront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/scsifront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/gntalloc: don't use gnttab_query_foreign_access()
+    - xen: remove gnttab_query_foreign_access()
+    - xen/9p: use alloc/free_pages_exact()
+    - xen/pvcalls: use alloc/free_pages_exact()
+    - xen/gnttab: fix gnttab_end_foreign_access() without page specified
+    - xen/netfront: react properly to failing gnttab_end_foreign_access_ref()
+    - Revert "ACPI: PM: s2idle: Cancel wakeup before dispatching EC GPE"
+    - Linux 5.15.28
+  * zfcpdump-kernel update to v5.15 (LP: #1965766)
+    - SAUCE: Audit: Fix incorrect static inline function declration.
+  * [22.04 FEAT] SMC-R v2 Support (LP: #1929035)
+    - net/smc: save stack space and allocate smc_init_info
+    - net/smc: prepare for SMC-Rv2 connection
+    - net/smc: add SMC-Rv2 connection establishment
+    - net/smc: add listen processing for SMC-Rv2
+    - net/smc: add v2 format of CLC decline message
+    - net/smc: retrieve v2 gid from IB device
+    - net/smc: add v2 support to the work request layer
+    - net/smc: extend LLC layer for SMC-Rv2
+    - net/smc: add netlink support for SMC-Rv2
+    - net/smc: stop links when their GID is removed
+    - net/smc: fix kernel panic caused by race of smc_sock
+    - net/smc: Fix hung_task when removing SMC-R devices
+  * [22.04 FEAT] Transparent PCI device recovery (LP: #1959532)
+    - s390/pci: tolerate inconsistent handle in recover
+    - s390/pci: add simpler s390dbf traces for events
+    - s390/pci: refresh function handle in iomap
+    - s390/pci: implement reset_slot for hotplug slot
+    - PCI: Export pci_dev_lock()
+    - s390/pci: implement minimal PCI error recovery
+  * Mute/mic LEDs no function on some HP platfroms (LP: #1965080)
+    - ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machines
+  * [22.04 FEAT] smc: Add User-defined EID (Enterprise ID) Support - kernel
+    (LP: #1929060)
+    - net/smc: add support for user defined EIDs
+    - net/smc: keep static copy of system EID
+    - net/smc: add generic netlink support for system EID
+  * Rotate to 2021v1 signing key (LP: #1964990)
+    - [Packaging] Rotate to 2021v1 signing key
+  * [22.04 FEAT] zcrypt DD: Exploitation Support of new IBM Z Crypto Hardware
+    (kernel part) (LP: #1959547)
+    - s390/zcrypt: rework of debug feature messages
+    - s390/ap/zcrypt: debug feature improvements
+    - s390/zcrypt: CEX8S exploitation support
+    - s390/zcrypt: handle checkstopped cards with new state
+    - s390/zcrypt: Support CPRB minor version T7
+    - s390/zcrypt: change reply buffer size offering
+    - s390/zcrypt: Provide target domain for EP11 cprbs to scheduling function
+    - s390/airq: use DMA memory for summary indicators
+  * [22.04 FEAT] [VS2103] Set KVM_CAP_S390_MEM_OP_EXTENSION capability to 211
+    (LP: #1963901)
+    - SAUCE: Set KVM_CAP_S390_MEM_OP_EXTENSION capability to 211
+  * dependency on crda obsolete according to Debian (LP: #1958918)
+    - [Packaging] switch dependency from crda to wireless-regdb
+  * Cirrus audio support [1028:0BB5] & [1028:0BB6] (LP: #1964748)
+    - ALSA: hda/cs8409: Add new Warlock SKUs to patch_cs8409
+  * Miscellaneous Ubuntu changes
+    - [Packaging] mark dkms-build-configure--zfs executable
+    - [Packaging] Fix bashism in dkms-build script
+    - [Packaging] Always catch errors in dkms-build scripts
+    - [Config] toolchain version update
+  * Miscellaneous upstream changes
+    - Ubuntu: remove leftover reference to ubuntu/hio driver
+    - Reverting commits 61005756c824 and cdb0f8e66513 due to a conflict with
+      LP#1929035. Re-pick them afterwards, which will establish the upstream
+      commit content and order again.
+    - Revert "UBUNTU: [Packaging] Rotate to 2021v1 signing key"
+
+  [ Ubuntu: 5.15.0-23.23 ]
+
+  * jammy/linux: 5.15.0-23.23 -proposed tracker (LP: #1964573)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync dkms-build{,--nvidia-N} from LRMv5
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+  * [22.04 FEAT] KVM: Enable GISA support for Secure Execution guests
+    (LP: #1959977)
+    - KVM: s390: pv: make use of ultravisor AIV support
+  * intel_iommu breaks Intel IPU6 camera: isys port open ready failed -16
+    (LP: #1958004)
+    - SAUCE: iommu: intel-ipu: use IOMMU passthrough mode for Intel IPUs
+  * CVE-2022-23960
+    - ARM: report Spectre v2 status through sysfs
+    - ARM: early traps initialisation
+    - ARM: use LOADADDR() to get load address of sections
+    - ARM: Spectre-BHB workaround
+    - ARM: include unprivileged BPF status in Spectre V2 reporting
+    - arm64: Add Neoverse-N2, Cortex-A710 CPU part definition
+    - arm64: Add HWCAP for self-synchronising virtual counter
+    - arm64: Add Cortex-X2 CPU part definition
+    - arm64: add ID_AA64ISAR2_EL1 sys register
+    - arm64: cpufeature: add HWCAP for FEAT_AFP
+    - arm64: cpufeature: add HWCAP for FEAT_RPRES
+    - arm64: entry.S: Add ventry overflow sanity checks
+    - arm64: spectre: Rename spectre_v4_patch_fw_mitigation_conduit
+    - KVM: arm64: Allow indirect vectors to be used without SPECTRE_V3A
+    - arm64: entry: Make the trampoline cleanup optional
+    - arm64: entry: Free up another register on kpti's tramp_exit path
+    - arm64: entry: Move the trampoline data page before the text page
+    - arm64: entry: Allow tramp_alias to access symbols after the 4K boundary
+    - arm64: entry: Don't assume tramp_vectors is the start of the vectors
+    - arm64: entry: Move trampoline macros out of ifdef'd section
+    - arm64: entry: Make the kpti trampoline's kpti sequence optional
+    - arm64: entry: Allow the trampoline text to occupy multiple pages
+    - arm64: entry: Add non-kpti __bp_harden_el1_vectors for mitigations
+    - arm64: entry: Add vectors that have the bhb mitigation sequences
+    - arm64: entry: Add macro for reading symbol addresses from the trampoline
+    - arm64: Add percpu vectors for EL1
+    - arm64: proton-pack: Report Spectre-BHB vulnerabilities as part of Spectre-v2
+    - arm64: Mitigate spectre style branch history side channels
+    - KVM: arm64: Allow SMCCC_ARCH_WORKAROUND_3 to be discovered and migrated
+    - arm64: Use the clearbhb instruction in mitigations
+    - arm64: proton-pack: Include unprivileged eBPF status in Spectre v2
+      mitigation reporting
+    - ARM: fix build error when BPF_SYSCALL is disabled
+  * CVE-2021-26401
+    - x86/speculation: Use generic retpoline by default on AMD
+    - x86/speculation: Update link to AMD speculation whitepaper
+    - x86/speculation: Warn about Spectre v2 LFENCE mitigation
+    - x86/speculation: Warn about eIBRS + LFENCE + Unprivileged eBPF + SMT
+  * CVE-2022-0001
+    - x86,bugs: Unconditionally allow spectre_v2=retpoline,amd
+    - x86/speculation: Rename RETPOLINE_AMD to RETPOLINE_LFENCE
+    - x86/speculation: Add eIBRS + Retpoline options
+    - Documentation/hw-vuln: Update spectre doc
+    - x86/speculation: Include unprivileged eBPF status in Spectre v2 mitigation
+      reporting
+  * Jammy update: v5.15.27 upstream stable release (LP: #1964361)
+    - mac80211_hwsim: report NOACK frames in tx_status
+    - mac80211_hwsim: initialize ieee80211_tx_info at hw_scan_work
+    - i2c: bcm2835: Avoid clock stretching timeouts
+    - ASoC: rt5668: do not block workqueue if card is unbound
+    - ASoC: rt5682: do not block workqueue if card is unbound
+    - regulator: core: fix false positive in regulator_late_cleanup()
+    - Input: clear BTN_RIGHT/MIDDLE on buttonpads
+    - btrfs: get rid of warning on transaction commit when using flushoncommit
+    - KVM: arm64: vgic: Read HW interrupt pending state from the HW
+    - block: loop:use kstatfs.f_bsize of backing file to set discard granularity
+    - tipc: fix a bit overflow in tipc_crypto_key_rcv()
+    - cifs: do not use uninitialized data in the owner/group sid
+    - cifs: fix double free race when mount fails in cifs_get_root()
+    - cifs: modefromsids must add an ACE for authenticated users
+    - selftests/seccomp: Fix seccomp failure by adding missing headers
+    - drm/amd/pm: correct UMD pstate clocks for Dimgrey Cavefish and Beige Goby
+    - dmaengine: shdma: Fix runtime PM imbalance on error
+    - i2c: cadence: allow COMPILE_TEST
+    - i2c: imx: allow COMPILE_TEST
+    - i2c: qup: allow COMPILE_TEST
+    - net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
+    - block-map: add __GFP_ZERO flag for alloc_page in function bio_copy_kern
+    - usb: gadget: don't release an existing dev->buf
+    - usb: gadget: clear related members when goto fail
+    - exfat: reuse exfat_inode_info variable instead of calling EXFAT_I()
+    - exfat: fix i_blocks for files truncated over 4 GiB
+    - tracing: Add test for user space strings when filtering on string pointers
+    - arm64: Mark start_backtrace() notrace and NOKPROBE_SYMBOL
+    - serial: stm32: prevent TDR register overwrite when sending x_char
+    - ext4: drop ineligible txn start stop APIs
+    - ext4: simplify updating of fast commit stats
+    - ext4: fast commit may not fallback for ineligible commit
+    - ext4: fast commit may miss file actions
+    - sched/fair: Fix fault in reweight_entity
+    - ata: pata_hpt37x: fix PCI clock detection
+    - drm/amdgpu: check vm ready by amdgpu_vm->evicting flag
+    - tracing: Add ustring operation to filtering string pointers
+    - ipv6: fix skb drops in igmp6_event_query() and igmp6_event_report()
+    - NFSD: Have legacy NFSD WRITE decoders use xdr_stream_subsegment()
+    - NFSD: Fix zero-length NFSv3 WRITEs
+    - io_uring: fix no lock protection for ctx->cq_extra
+    - tools/resolve_btf_ids: Close ELF file on error
+    - mtd: spi-nor: Fix mtd size for s3an flashes
+    - MIPS: fix local_{add,sub}_return on MIPS64
+    - signal: In get_signal test for signal_group_exit every time through the loop
+    - PCI: mediatek-gen3: Disable DVFSRC voltage request
+    - PCI: rcar: Check if device is runtime suspended instead of
+      __clk_is_enabled()
+    - PCI: dwc: Do not remap invalid res
+    - PCI: aardvark: Fix checking for MEM resource type
+    - KVM: VMX: Don't unblock vCPU w/ Posted IRQ if IRQs are disabled in guest
+    - KVM: s390: Ensure kvm_arch_no_poll() is read once when blocking vCPU
+    - KVM: VMX: Read Posted Interrupt "control" exactly once per loop iteration
+    - KVM: X86: Ensure that dirty PDPTRs are loaded
+    - KVM: x86: Handle 32-bit wrap of EIP for EMULTYPE_SKIP with flat code seg
+    - KVM: x86: Exit to userspace if emulation prepared a completion callback
+    - i3c: fix incorrect address slot lookup on 64-bit
+    - i3c/master/mipi-i3c-hci: Fix a potentially infinite loop in
+      'hci_dat_v1_get_index()'
+    - tracing: Do not let synth_events block other dyn_event systems during create
+    - Input: ti_am335x_tsc - set ADCREFM for X configuration
+    - Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2
+    - PCI: mvebu: Check for errors from pci_bridge_emul_init() call
+    - PCI: mvebu: Do not modify PCI IO type bits in conf_write
+    - PCI: mvebu: Fix support for bus mastering and PCI_COMMAND on emulated bridge
+    - PCI: mvebu: Fix configuring secondary bus of PCIe Root Port via emulated
+      bridge
+    - PCI: mvebu: Setup PCIe controller to Root Complex mode
+    - PCI: mvebu: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
+    - PCI: mvebu: Fix support for PCI_EXP_DEVCTL on emulated bridge
+    - PCI: mvebu: Fix support for PCI_EXP_RTSTA on emulated bridge
+    - PCI: mvebu: Fix support for DEVCAP2, DEVCTL2 and LNKCTL2 registers on
+      emulated bridge
+    - NFSD: Fix verifier returned in stable WRITEs
+    - Revert "nfsd: skip some unnecessary stats in the v4 case"
+    - nfsd: fix crash on COPY_NOTIFY with special stateid
+    - x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
+    - drm/i915: don't call free_mmap_offset when purging
+    - SUNRPC: Fix sockaddr handling in the svc_xprt_create_error trace point
+    - SUNRPC: Fix sockaddr handling in svcsock_accept_class trace points
+    - drm/sun4i: dw-hdmi: Fix missing put_device() call in sun8i_hdmi_phy_get
+    - drm/atomic: Check new_crtc_state->active to determine if CRTC needs disable
+      in self refresh mode
+    - ntb_hw_switchtec: Fix pff ioread to read into mmio_part_cfg_all
+    - ntb_hw_switchtec: Fix bug with more than 32 partitions
+    - drm/amdkfd: Check for null pointer after calling kmemdup
+    - drm/amdgpu: use spin_lock_irqsave to avoid deadlock by local interrupt
+    - i3c: master: dw: check return of dw_i3c_master_get_free_pos()
+    - dma-buf: cma_heap: Fix mutex locking section
+    - tracing/uprobes: Check the return value of kstrdup() for tu->filename
+    - tracing/probes: check the return value of kstrndup() for pbuf
+    - mm: defer kmemleak object creation of module_alloc()
+    - kasan: fix quarantine conflicting with init_on_free
+    - selftests/vm: make charge_reserved_hugetlb.sh work with existing cgroup
+      setting
+    - hugetlbfs: fix off-by-one error in hugetlb_vmdelete_list()
+    - drm/amdgpu/display: Only set vblank_disable_immediate when PSR is not
+      enabled
+    - drm/amdgpu: filter out radeon PCI device IDs
+    - drm/amdgpu: filter out radeon secondary ids as well
+    - drm/amd/display: Use adjusted DCN301 watermarks
+    - drm/amd/display: move FPU associated DSC code to DML folder
+    - ethtool: Fix link extended state for big endian
+    - octeontx2-af: Optimize KPU1 processing for variable-length headers
+    - octeontx2-af: Reset PTP config in FLR handler
+    - octeontx2-af: cn10k: RPM hardware timestamp configuration
+    - octeontx2-af: cn10k: Use appropriate register for LMAC enable
+    - octeontx2-af: Adjust LA pointer for cpt parse header
+    - octeontx2-af: Add KPU changes to parse NGIO as separate layer
+    - net/mlx5e: IPsec: Refactor checksum code in tx data path
+    - net/mlx5e: IPsec: Fix crypto offload for non TCP/UDP encapsulated traffic
+    - bpf: Use u64_stats_t in struct bpf_prog_stats
+    - bpf: Fix possible race in inc_misses_counter
+    - drm/amd/display: Update watermark values for DCN301
+    - drm: mxsfb: Set fallback bus format when the bridge doesn't provide one
+    - drm: mxsfb: Fix NULL pointer dereference
+    - riscv/mm: Add XIP_FIXUP for phys_ram_base
+    - drm/i915/display: split out dpt out of intel_display.c
+    - drm/i915/display: Move DRRS code its own file
+    - drm/i915: Disable DRRS on IVB/HSW port != A
+    - gve: Recording rx queue before sending to napi
+    - net: dsa: ocelot: seville: utilize of_mdiobus_register
+    - net: dsa: seville: register the mdiobus under devres
+    - ibmvnic: don't release napi in __ibmvnic_open()
+    - of: net: move of_net under net/
+    - net: ethernet: litex: Add the dependency on HAS_IOMEM
+    - drm/mediatek: mtk_dsi: Reset the dsi0 hardware
+    - cifs: protect session channel fields with chan_lock
+    - cifs: fix confusing unneeded warning message on smb2.1 and earlier
+    - drm/amd/display: Fix stream->link_enc unassigned during stream removal
+    - bnxt_en: Fix occasional ethtool -t loopback test failures
+    - drm/amd/display: For vblank_disable_immediate, check PSR is really used
+    - PCI: mvebu: Fix device enumeration regression
+    - net: of: fix stub of_net helpers for CONFIG_NET=n
+    - ALSA: intel_hdmi: Fix reference to PCM buffer address
+    - ucounts: Fix systemd LimitNPROC with private users regression
+    - riscv/efi_stub: Fix get_boot_hartid_from_fdt() return value
+    - riscv: Fix config KASAN && SPARSEMEM && !SPARSE_VMEMMAP
+    - riscv: Fix config KASAN && DEBUG_VIRTUAL
+    - iwlwifi: mvm: check debugfs_dir ptr before use
+    - ASoC: ops: Shift tested values in snd_soc_put_volsw() by +min
+    - iommu/vt-d: Fix double list_add when enabling VMD in scalable mode
+    - iommu/amd: Recover from event log overflow
+    - drm/i915: s/JSP2/ICP2/ PCH
+    - drm/amd/display: Reduce dmesg error to a debug print
+    - xen/netfront: destroy queues before real_num_tx_queues is zeroed
+    - thermal: core: Fix TZ_GET_TRIP NULL pointer dereference
+    - mac80211: fix EAPoL rekey fail in 802.3 rx path
+    - blktrace: fix use after free for struct blk_trace
+    - ntb: intel: fix port config status offset for SPR
+    - mm: Consider __GFP_NOWARN flag for oversized kvmalloc() calls
+    - xfrm: fix MTU regression
+    - netfilter: fix use-after-free in __nf_register_net_hook()
+    - bpf, sockmap: Do not ignore orig_len parameter
+    - xfrm: fix the if_id check in changelink
+    - xfrm: enforce validity of offload input flags
+    - e1000e: Correct NVM checksum verification flow
+    - net: fix up skbs delta_truesize in UDP GRO frag_list
+    - netfilter: nf_queue: don't assume sk is full socket
+    - netfilter: nf_queue: fix possible use-after-free
+    - netfilter: nf_queue: handle socket prefetch
+    - batman-adv: Request iflink once in batadv-on-batadv check
+    - batman-adv: Request iflink once in batadv_get_real_netdevice
+    - batman-adv: Don't expect inter-netns unique iflink indices
+    - net: ipv6: ensure we call ipv6_mc_down() at most once
+    - net: dcb: flush lingering app table entries for unregistered devices
+    - net: ipa: add an interconnect dependency
+    - net/smc: fix connection leak
+    - net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error generated by client
+    - net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error cause by server
+    - btrfs: fix ENOSPC failure when attempting direct IO write into NOCOW range
+    - mac80211: fix forwarded mesh frames AC & queue selection
+    - net: stmmac: fix return value of __setup handler
+    - mac80211: treat some SAE auth steps as final
+    - iavf: Fix missing check for running netdev
+    - net: sxgbe: fix return value of __setup handler
+    - ibmvnic: register netdev after init of adapter
+    - net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe()
+    - ixgbe: xsk: change !netif_carrier_ok() handling in ixgbe_xmit_zc()
+    - iavf: Fix deadlock in iavf_reset_task
+    - efivars: Respect "block" flag in efivar_entry_set_safe()
+    - auxdisplay: lcd2s: Fix lcd2s_redefine_char() feature
+    - firmware: arm_scmi: Remove space in MODULE_ALIAS name
+    - ASoC: cs4265: Fix the duplicated control name
+    - auxdisplay: lcd2s: Fix memory leak in ->remove()
+    - auxdisplay: lcd2s: Use proper API to free the instance of charlcd object
+    - can: gs_usb: change active_channels's type from atomic_t to u8
+    - iommu/tegra-smmu: Fix missing put_device() call in tegra_smmu_find
+    - arm64: dts: rockchip: Switch RK3399-Gru DP to SPDIF output
+    - igc: igc_read_phy_reg_gpy: drop premature return
+    - ARM: Fix kgdb breakpoint for Thumb2
+    - mips: setup: fix setnocoherentio() boolean setting
+    - ARM: 9182/1: mmu: fix returns from early_param() and __setup() functions
+    - mptcp: Correctly set DATA_FIN timeout when number of retransmits is large
+    - selftests: mlxsw: tc_police_scale: Make test more robust
+    - pinctrl: sunxi: Use unique lockdep classes for IRQs
+    - igc: igc_write_phy_reg_gpy: drop premature return
+    - ibmvnic: free reset-work-item when flushing
+    - memfd: fix F_SEAL_WRITE after shmem huge page allocated
+    - s390/extable: fix exception table sorting
+    - sched: Fix yet more sched_fork() races
+    - arm64: dts: juno: Remove GICv2m dma-range
+    - iommu/amd: Fix I/O page table memory leak
+    - MIPS: ralink: mt7621: do memory detection on KSEG1
+    - ARM: dts: switch timer config to common devkit8000 devicetree
+    - ARM: dts: Use 32KiHz oscillator on devkit8000
+    - soc: fsl: guts: Revert commit 3c0d64e867ed
+    - soc: fsl: guts: Add a missing memory allocation failure check
+    - soc: fsl: qe: Check of ioremap return value
+    - netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
+    - ARM: tegra: Move panels to AUX bus
+    - can: etas_es58x: change opened_channel_cnt's type from atomic_t to u8
+    - net: stmmac: enhance XDP ZC driver level switching performance
+    - net: stmmac: only enable DMA interrupts when ready
+    - ibmvnic: initialize rc before completing wait
+    - ibmvnic: define flush_reset_queue helper
+    - ibmvnic: complete init_done on transport events
+    - net: chelsio: cxgb3: check the return value of pci_find_capability()
+    - net: sparx5: Fix add vlan when invalid operation
+    - iavf: Refactor iavf state machine tracking
+    - iavf: Add __IAVF_INIT_FAILED state
+    - iavf: Combine init and watchdog state machines
+    - iavf: Add trace while removing device
+    - iavf: Rework mutexes for better synchronisation
+    - iavf: Add helper function to go from pci_dev to adapter
+    - iavf: Fix kernel BUG in free_msi_irqs
+    - iavf: Add waiting so the port is initialized in remove
+    - iavf: Fix init state closure on remove
+    - iavf: Fix locking for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS
+    - iavf: Fix race in init state
+    - iavf: Fix __IAVF_RESETTING state usage
+    - drm/i915/guc/slpc: Correct the param count for unset param
+    - drm/bridge: ti-sn65dsi86: Properly undo autosuspend
+    - e1000e: Fix possible HW unit hang after an s0ix exit
+    - MIPS: ralink: mt7621: use bitwise NOT instead of logical
+    - nl80211: Handle nla_memdup failures in handle_nan_filter
+    - drm/amdgpu: fix suspend/resume hang regression
+    - net: dcb: disable softirqs in dcbnl_flush_dev()
+    - selftests: mlxsw: resource_scale: Fix return value
+    - net: stmmac: perserve TX and RX coalesce value during XDP setup
+    - iavf: do not override the adapter state in the watchdog task (again)
+    - iavf: missing unlocks in iavf_watchdog_task()
+    - MAINTAINERS: adjust file entry for of_net.c after movement
+    - Input: elan_i2c - move regulator_[en|dis]able() out of
+      elan_[en|dis]able_power()
+    - Input: elan_i2c - fix regulator enable count imbalance after suspend/resume
+    - Input: samsung-keypad - properly state IOMEM dependency
+    - HID: add mapping for KEY_DICTATE
+    - HID: add mapping for KEY_ALL_APPLICATIONS
+    - tracing/histogram: Fix sorting on old "cpu" value
+    - tracing: Fix return value of __setup handlers
+    - btrfs: fix lost prealloc extents beyond eof after full fsync
+    - btrfs: fix relocation crash due to premature return from
+      btrfs_commit_transaction()
+    - btrfs: do not WARN_ON() if we have PageError set
+    - btrfs: qgroup: fix deadlock between rescan worker and remove qgroup
+    - btrfs: add missing run of delayed items after unlink during log replay
+    - btrfs: do not start relocation until in progress drops are done
+    - Revert "xfrm: xfrm_state_mtu should return at least 1280 for ipv6"
+    - proc: fix documentation and description of pagemap
+    - KVM: x86/mmu: Passing up the error state of mmu_alloc_shadow_roots()
+    - hamradio: fix macro redefine warning
+    - Linux 5.15.27
+    - [Config] updateconfigs
+  * devices on thunderbolt dock are not recognized on adl-p platform
+    (LP: #1955016)
+    - thunderbolt: Tear down existing tunnels when resuming from hibernate
+    - thunderbolt: Runtime resume USB4 port when retimers are scanned
+    - thunderbolt: Do not allow subtracting more NFC credits than configured
+    - thunderbolt: Do not program path HopIDs for USB4 routers
+    - thunderbolt: Add debug logging of DisplayPort resource allocation
+  * MT7921[14c3:7961] ASPM is disabled and it affects power consumption
+    (LP: #1955882)
+    - mt76: mt7921: enable aspm by default
+  * Add proper runtime PM support to Realtek PCIe cardreader (LP: #1963615)
+    - mmc: rtsx: Use pm_runtime_{get, put}() to handle runtime PM
+    - misc: rtsx: Rework runtime power management flow
+    - misc: rtsx: Cleanup power management ops
+    - misc: rtsx: Quiesce rts5249 on system suspend
+    - mmc: rtsx: Let MMC core handle runtime PM
+    - misc: rtsx: conditionally build rtsx_pm_power_saving()
+    - misc: rtsx: rts522a rts5228 rts5261 support Runtime PM
+    - mmc: rtsx: Fix build errors/warnings for unused variable
+    - mmc: rtsx: add 74 Clocks in power on flow
+  * [22.04 FEAT] In-kernel crypto: SIMD implementation of chacha20
+    (LP: #1853152)
+    - s390/crypto: add SIMD implementation for ChaCha20
+    - s390/crypto: fix compile error for ChaCha20 module
+  * Add ConnectX7 support and bug fixes  to Jammy (LP: #1962185)
+    - IB/mlx5: Expose NDR speed through MAD
+  * INVALID or PRIVATE BUG (LP: #1959890)
+    - [Config] Deactivate CONFIG_QETH_OSX kernel config option
+  * Move virtual graphics drivers from linux-modules-extra to linux-modules
+    (LP: #1960633)
+    - [Packaging] Move VM DRM drivers into modules
+  * Not able to enter s2idle state on AMD platforms (LP: #1961121)
+    - HID: amd_sfh: Handle amd_sfh work buffer in PM ops
+    - HID: amd_sfh: Disable the interrupt for all command
+    - HID: amd_sfh: Add functionality to clear interrupts
+    - HID: amd_sfh: Add interrupt handler to process interrupts
+  * INVALID or PRIVATE BUG (LP: #1960580)
+    - s390/kexec_file: move kernel image size check
+    - s390: support command lines longer than 896 bytes
+  * [UBUNTU 20.04] kernel: Add support for CPU-MF counter second version 7
+    (LP: #1960182)
+    - s390/cpumf: Support for CPU Measurement Facility CSVN 7
+    - s390/cpumf: Support for CPU Measurement Sampling Facility LS bit
+  * [SRU]PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is
+    enabled by IOMMU (LP: #1937295)
+    - PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled
+      by IOMMU
+  * Jammy update: v5.15.26 upstream stable release (LP: #1963891)
+    - mm/filemap: Fix handling of THPs in generic_file_buffered_read()
+    - cgroup/cpuset: Fix a race between cpuset_attach() and cpu hotplug
+    - cgroup-v1: Correct privileges check in release_agent writes
+    - x86/ptrace: Fix xfpregs_set()'s incorrect xmm clearing
+    - btrfs: tree-checker: check item_size for inode_item
+    - btrfs: tree-checker: check item_size for dev_item
+    - clk: jz4725b: fix mmc0 clock gating
+    - io_uring: don't convert to jiffies for waiting on timeouts
+    - io_uring: disallow modification of rsrc_data during quiesce
+    - selinux: fix misuse of mutex_is_locked()
+    - vhost/vsock: don't check owner in vhost_vsock_stop() while releasing
+    - parisc/unaligned: Fix fldd and fstd unaligned handlers on 32-bit kernel
+    - parisc/unaligned: Fix ldw() and stw() unalignment handlers
+    - KVM: x86/mmu: make apf token non-zero to fix bug
+    - drm/amd/display: Protect update_bw_bounding_box FPU code.
+    - drm/amd/pm: fix some OEM SKU specific stability issues
+    - drm/amd: Check if ASPM is enabled from PCIe subsystem
+    - drm/amdgpu: disable MMHUB PG for Picasso
+    - drm/amdgpu: do not enable asic reset for raven2
+    - drm/i915: Widen the QGV point mask
+    - drm/i915: Correctly populate use_sagv_wm for all pipes
+    - drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV
+    - sr9700: sanity check for packet length
+    - USB: zaurus: support another broken Zaurus
+    - CDC-NCM: avoid overflow in sanity checking
+    - netfilter: xt_socket: fix a typo in socket_mt_destroy()
+    - netfilter: xt_socket: missing ifdef CONFIG_IP6_NF_IPTABLES dependency
+    - tee: export teedev_open() and teedev_close_context()
+    - optee: use driver internal tee_context for some rpc
+    - ping: remove pr_err from ping_lookup
+    - Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
+    - gpu: host1x: Always return syncpoint value when waiting
+    - perf evlist: Fix failed to use cpu list for uncore events
+    - perf data: Fix double free in perf_session__delete()
+    - mptcp: fix race in incoming ADD_ADDR option processing
+    - mptcp: add mibs counter for ignored incoming options
+    - selftests: mptcp: fix diag instability
+    - selftests: mptcp: be more conservative with cookie MPJ limits
+    - bnx2x: fix driver load from initrd
+    - bnxt_en: Fix active FEC reporting to ethtool
+    - bnxt_en: Fix offline ethtool selftest with RDMA enabled
+    - bnxt_en: Fix incorrect multicast rx mask setting when not requested
+    - hwmon: Handle failure to register sensor with thermal zone correctly
+    - net/mlx5: Fix tc max supported prio for nic mode
+    - ice: check the return of ice_ptp_gettimex64
+    - ice: initialize local variable 'tlv'
+    - net/mlx5: Update the list of the PCI supported devices
+    - bpf: Fix crash due to incorrect copy_map_value
+    - bpf: Do not try bpf_msg_push_data with len 0
+    - selftests: bpf: Check bpf_msg_push_data return value
+    - bpf: Fix a bpf_timer initialization issue
+    - bpf: Add schedule points in batch ops
+    - io_uring: add a schedule point in io_add_buffers()
+    - net: __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor friends
+    - nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
+    - tipc: Fix end of loop tests for list_for_each_entry()
+    - gso: do not skip outer ip header in case of ipip and net_failover
+    - net: mv643xx_eth: process retval from of_get_mac_address
+    - openvswitch: Fix setting ipv6 fields causing hw csum failure
+    - drm/edid: Always set RGB444
+    - net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
+    - drm/vc4: crtc: Fix runtime_pm reference counting
+    - drm/i915/dg2: Print PHY name properly on calibration error
+    - net/sched: act_ct: Fix flow table lookup after ct clear or switching zones
+    - net: ll_temac: check the return value of devm_kmalloc()
+    - net: Force inlining of checksum functions in net/checksum.h
+    - netfilter: nf_tables: unregister flowtable hooks on netns exit
+    - nfp: flower: Fix a potential leak in nfp_tunnel_add_shared_mac()
+    - net: mdio-ipq4019: add delay after clock enable
+    - netfilter: nf_tables: fix memory leak during stateful obj update
+    - net/smc: Use a mutex for locking "struct smc_pnettable"
+    - surface: surface3_power: Fix battery readings on batteries without a serial
+      number
+    - udp_tunnel: Fix end of loop test in udp_tunnel_nic_unregister()
+    - net/mlx5: DR, Cache STE shadow memory
+    - ibmvnic: schedule failover only if vioctl fails
+    - net/mlx5: DR, Don't allow match on IP w/o matching on full
+      ethertype/ip_version
+    - net/mlx5: Fix possible deadlock on rule deletion
+    - net/mlx5: Fix wrong limitation of metadata match on ecpf
+    - net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
+    - net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
+    - net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
+    - net/mlx5: Update log_max_qp value to be 17 at most
+    - spi: spi-zynq-qspi: Fix a NULL pointer dereference in
+      zynq_qspi_exec_mem_op()
+    - gpio: rockchip: Reset int_bothedge when changing trigger
+    - regmap-irq: Update interrupt clear register for proper reset
+    - net-timestamp: convert sk->sk_tskey to atomic_t
+    - RDMA/rtrs-clt: Fix possible double free in error case
+    - RDMA/rtrs-clt: Move free_permit from free_clt to rtrs_clt_close
+    - bnxt_en: Increase firmware message response DMA wait time
+    - configfs: fix a race in configfs_{,un}register_subsystem()
+    - RDMA/ib_srp: Fix a deadlock
+    - tracing: Dump stacktrace trigger to the corresponding instance
+    - tracing: Have traceon and traceoff trigger honor the instance
+    - iio:imu:adis16480: fix buffering for devices with no burst mode
+    - iio: adc: men_z188_adc: Fix a resource leak in an error handling path
+    - iio: adc: tsc2046: fix memory corruption by preventing array overflow
+    - iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
+    - iio: accel: fxls8962af: add padding to regmap for SPI
+    - iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
+    - iio: Fix error handling for PM
+    - sc16is7xx: Fix for incorrect data being transmitted
+    - ata: pata_hpt37x: disable primary channel on HPT371
+    - Revert "USB: serial: ch341: add new Product ID for CH341A"
+    - usb: gadget: rndis: add spinlock for rndis response list
+    - USB: gadget: validate endpoint index for xilinx udc
+    - tracefs: Set the group ownership in apply_options() not parse_options()
+    - USB: serial: option: add support for DW5829e
+    - USB: serial: option: add Telit LE910R1 compositions
+    - usb: dwc2: drd: fix soft connect when gadget is unconfigured
+    - usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail
+    - usb: dwc3: pci: Fix Bay Trail phy GPIO mappings
+    - usb: dwc3: gadget: Let the interrupt handler disable bottom halves.
+    - xhci: re-initialize the HC during resume if HCE was set
+    - xhci: Prevent futile URB re-submissions due to incorrect return value.
+    - nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
+    - mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
+    - driver core: Free DMA range map when device is released
+    - btrfs: prevent copying too big compressed lzo segment
+    - RDMA/cma: Do not change route.addr.src_addr outside state checks
+    - thermal: int340x: fix memory leak in int3400_notify()
+    - staging: fbtft: fb_st7789v: reset display before initialization
+    - tps6598x: clear int mask on probe failure
+    - IB/qib: Fix duplicate sysfs directory name
+    - riscv: fix nommu_k210_sdcard_defconfig
+    - riscv: fix oops caused by irqsoff latency tracer
+    - tty: n_gsm: fix encoding of control signal octet bit DV
+    - tty: n_gsm: fix proper link termination after failed open
+    - tty: n_gsm: fix NULL pointer access due to DLCI release
+    - tty: n_gsm: fix wrong tty control line for flow control
+    - tty: n_gsm: fix wrong modem processing in convergence layer type 2
+    - tty: n_gsm: fix deadlock in gsmtty_open()
+    - pinctrl: fix loop in k210_pinconf_get_drive()
+    - pinctrl: k210: Fix bias-pull-up
+    - gpio: tegra186: Fix chip_data type confusion
+    - memblock: use kfree() to release kmalloced memblock regions
+    - ice: Fix race conditions between virtchnl handling and VF ndo ops
+    - ice: fix concurrent reset and removal of VFs
+    - Linux 5.15.26
+  * Jammy update: v5.15.25 upstream stable release (LP: #1963890)
+    - drm/nouveau/pmu/gm200-: use alternate falcon reset sequence
+    - fs/proc: task_mmu.c: don't read mapcount for migration entry
+    - btrfs: zoned: cache reported zone during mount
+    - HID:Add support for UGTABLET WP5540
+    - Revert "svm: Add warning message for AVIC IPI invalid target"
+    - parisc: Show error if wrong 32/64-bit compiler is being used
+    - serial: parisc: GSC: fix build when IOSAPIC is not set
+    - parisc: Drop __init from map_pages declaration
+    - parisc: Fix data TLB miss in sba_unmap_sg
+    - parisc: Fix sglist access in ccio-dma.c
+    - mmc: block: fix read single on recovery logic
+    - mm: don't try to NUMA-migrate COW pages that have other uses
+    - HID: amd_sfh: Add illuminance mask to limit ALS max value
+    - HID: i2c-hid: goodix: Fix a lockdep splat
+    - HID: amd_sfh: Increase sensor command timeout
+    - HID: amd_sfh: Correct the structure field name
+    - PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA
+      topology
+    - parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()
+    - btrfs: send: in case of IO error log it
+    - platform/x86: touchscreen_dmi: Add info for the RWC NANOTE P8 AY07J 2-in-1
+    - platform/x86: ISST: Fix possible circular locking dependency detected
+    - kunit: tool: Import missing importlib.abc
+    - selftests: rtc: Increase test timeout so that all tests run
+    - kselftest: signal all child processes
+    - net: ieee802154: at86rf230: Stop leaking skb's
+    - selftests/zram: Skip max_comp_streams interface on newer kernel
+    - selftests/zram01.sh: Fix compression ratio calculation
+    - selftests/zram: Adapt the situation that /dev/zram0 is being used
+    - selftests: openat2: Print also errno in failure messages
+    - selftests: openat2: Add missing dependency in Makefile
+    - selftests: openat2: Skip testcases that fail with EOPNOTSUPP
+    - selftests: skip mincore.check_file_mmap when fs lacks needed support
+    - ax25: improve the incomplete fix to avoid UAF and NPD bugs
+    - pinctrl: bcm63xx: fix unmet dependency on REGMAP for GPIO_REGMAP
+    - vfs: make freeze_super abort when sync_filesystem returns error
+    - quota: make dquot_quota_sync return errors from ->sync_fs
+    - scsi: pm80xx: Fix double completion for SATA devices
+    - kselftest: Fix vdso_test_abi return status
+    - scsi: core: Reallocate device's budget map on queue depth change
+    - scsi: pm8001: Fix use-after-free for aborted TMF sas_task
+    - scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task
+    - drm/amd: Warn users about potential s0ix problems
+    - nvme: fix a possible use-after-free in controller reset during load
+    - nvme-tcp: fix possible use-after-free in transport error_recovery work
+    - nvme-rdma: fix possible use-after-free in transport error_recovery work
+    - net: sparx5: do not refer to skb after passing it on
+    - drm/amd: add support to check whether the system is set to s3
+    - drm/amd: Only run s3 or s0ix if system is configured properly
+    - drm/amdgpu: fix logic inversion in check
+    - x86/Xen: streamline (and fix) PV CPU enumeration
+    - Revert "module, async: async_synchronize_full() on module init iff async is
+      used"
+    - gcc-plugins/stackleak: Use noinstr in favor of notrace
+    - random: wake up /dev/random writers after zap
+    - KVM: x86/xen: Fix runstate updates to be atomic when preempting vCPU
+    - KVM: x86: nSVM/nVMX: set nested_run_pending on VM entry which is a result of
+      RSM
+    - KVM: x86: SVM: don't passthrough SMAP/SMEP/PKE bits in !NPT && !gCR0.PG case
+    - KVM: x86: nSVM: fix potential NULL derefernce on nested migration
+    - KVM: x86: nSVM: mark vmcb01 as dirty when restoring SMM saved state
+    - iwlwifi: fix use-after-free
+    - drm/radeon: Fix backlight control on iMac 12,1
+    - drm/atomic: Don't pollute crtc_state->mode_blob with error pointers
+    - drm/amd/pm: correct the sequence of sending gpu reset msg
+    - drm/amdgpu: skipping SDMA hw_init and hw_fini for S0ix.
+    - drm/i915/opregion: check port number bounds for SWSCI display power state
+    - drm/i915: Fix dbuf slice config lookup
+    - drm/i915: Fix mbus join config lookup
+    - vsock: remove vsock from connected table when connect is interrupted by a
+      signal
+    - drm/cma-helper: Set VM_DONTEXPAND for mmap
+    - drm/i915/gvt: Make DRM_I915_GVT depend on X86
+    - drm/i915/ttm: tweak priority hint selection
+    - iwlwifi: pcie: fix locking when "HW not ready"
+    - iwlwifi: pcie: gen2: fix locking when "HW not ready"
+    - iwlwifi: mvm: don't send SAR GEO command for 3160 devices
+    - selftests: netfilter: fix exit value for nft_concat_range
+    - netfilter: nft_synproxy: unregister hooks on init error path
+    - selftests: netfilter: disable rp_filter on router
+    - ipv4: fix data races in fib_alias_hw_flags_set
+    - ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
+    - ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
+    - ipv6: per-netns exclusive flowlabel checks
+    - Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
+    - mac80211: mlme: check for null after calling kmemdup
+    - brcmfmac: firmware: Fix crash in brcm_alt_fw_path
+    - cfg80211: fix race in netlink owner interface destruction
+    - net: dsa: lan9303: fix reset on probe
+    - net: dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
+    - net: dsa: lantiq_gswip: fix use after free in gswip_remove()
+    - net: dsa: lan9303: handle hwaccel VLAN tags
+    - net: dsa: lan9303: add VLAN IDs to master device
+    - net: ieee802154: ca8210: Fix lifs/sifs periods
+    - ping: fix the dif and sdif check in ping_lookup
+    - bonding: force carrier update when releasing slave
+    - drop_monitor: fix data-race in dropmon_net_event / trace_napi_poll_hit
+    - net_sched: add __rcu annotation to netdev->qdisc
+    - bonding: fix data-races around agg_select_timer
+    - libsubcmd: Fix use-after-free for realloc(..., 0)
+    - net/smc: Avoid overwriting the copies of clcsock callback functions
+    - net: phy: mediatek: remove PHY mode check on MT7531
+    - atl1c: fix tx timeout after link flap on Mikrotik 10/25G NIC
+    - tipc: fix wrong publisher node address in link publications
+    - dpaa2-switch: fix default return of dpaa2_switch_flower_parse_mirror_key
+    - dpaa2-eth: Initialize mutex used in one step timestamping path
+    - net: bridge: multicast: notify switchdev driver whenever MC processing gets
+      disabled
+    - perf bpf: Defer freeing string after possible strlen() on it
+    - selftests/exec: Add non-regular to TEST_GEN_PROGS
+    - arm64: Correct wrong label in macro __init_el2_gicv3
+    - ALSA: usb-audio: revert to IMPLICIT_FB_FIXED_DEV for M-Audio FastTrack Ultra
+    - ALSA: hda/realtek: Add quirk for Legion Y9000X 2019
+    - ALSA: hda/realtek: Fix deadlock by COEF mutex
+    - ALSA: hda: Fix regression on forced probe mask option
+    - ALSA: hda: Fix missing codec probe on Shenker Dock 15
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_range()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_sx()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_xr_sx()
+    - cifs: fix set of group SID via NTSD xattrs
+    - powerpc/603: Fix boot failure with DEBUG_PAGEALLOC and KFENCE
+    - powerpc/lib/sstep: fix 'ptesync' build error
+    - mtd: rawnand: gpmi: don't leak PM reference in error path
+    - smb3: fix snapshot mount option
+    - tipc: fix wrong notification node addresses
+    - scsi: ufs: Remove dead code
+    - scsi: ufs: Fix a deadlock in the error handler
+    - ASoC: tas2770: Insert post reset delay
+    - ASoC: qcom: Actually clear DMA interrupt register for HDMI
+    - block/wbt: fix negative inflight counter when remove scsi device
+    - NFS: Remove an incorrect revalidation in nfs4_update_changeattr_locked()
+    - NFS: LOOKUP_DIRECTORY is also ok with symlinks
+    - NFS: Do not report writeback errors in nfs_getattr()
+    - tty: n_tty: do not look ahead for EOL character past the end of the buffer
+    - block: fix surprise removal for drivers calling blk_set_queue_dying
+    - mtd: rawnand: qcom: Fix clock sequencing in qcom_nandc_probe()
+    - mtd: parsers: qcom: Fix kernel panic on skipped partition
+    - mtd: parsers: qcom: Fix missing free for pparts in cleanup
+    - mtd: phram: Prevent divide by zero bug in phram_setup()
+    - mtd: rawnand: brcmnand: Fixed incorrect sub-page ECC status
+    - HID: elo: fix memory leak in elo_probe
+    - mtd: rawnand: ingenic: Fix missing put_device in ingenic_ecc_get
+    - Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj
+    - KVM: x86/pmu: Refactoring find_arch_event() to pmc_perf_hw_id()
+    - KVM: x86/pmu: Don't truncate the PerfEvtSeln MSR when creating a perf event
+    - KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW
+    - ARM: OMAP2+: hwmod: Add of_node_put() before break
+    - ARM: OMAP2+: adjust the location of put_device() call in omapdss_init_of
+    - phy: usb: Leave some clocks running during suspend
+    - staging: vc04_services: Fix RCU dereference check
+    - phy: phy-mtk-tphy: Fix duplicated argument in phy-mtk-tphy
+    - irqchip/sifive-plic: Add missing thead,c900-plic match string
+    - x86/bug: Merge annotate_reachable() into _BUG_FLAGS() asm
+    - netfilter: conntrack: don't refresh sctp entries in closed state
+    - ksmbd: fix same UniqueId for dot and dotdot entries
+    - ksmbd: don't align last entry offset in smb2 query directory
+    - arm64: dts: meson-gx: add ATF BL32 reserved-memory region
+    - arm64: dts: meson-g12: add ATF BL32 reserved-memory region
+    - arm64: dts: meson-g12: drop BL32 region from SEI510/SEI610
+    - pidfd: fix test failure due to stack overflow on some arches
+    - selftests: fixup build warnings in pidfd / clone3 tests
+    - mm: io_uring: allow oom-killer from io_uring_setup
+    - kconfig: let 'shell' return enough output for deep path names
+    - ata: libata-core: Disable TRIM on M88V29
+    - soc: aspeed: lpc-ctrl: Block error printing on probe defer cases
+    - xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create
+    - drm/rockchip: dw_hdmi: Do not leave clock enabled in error case
+    - tracing: Fix tp_printk option related with tp_printk_stop_on_boot
+    - display/amd: decrease message verbosity about watermarks table failure
+    - drm/amd/display: Cap pflip irqs per max otg number
+    - drm/amd/display: fix yellow carp wm clamping
+    - net: usb: qmi_wwan: Add support for Dell DW5829e
+    - net: macb: Align the dma and coherent dma masks
+    - kconfig: fix failing to generate auto.conf
+    - scsi: lpfc: Fix pt2pt NVMe PRLI reject LOGO loop
+    - EDAC: Fix calculation of returned address and next offset in
+      edac_align_ptr()
+    - ucounts: Handle wrapping in is_ucounts_overlimit
+    - ucounts: In set_cred_ucounts assume new->ucounts is non-NULL
+    - ucounts: Base set_cred_ucounts changes on the real user
+    - ucounts: Enforce RLIMIT_NPROC not RLIMIT_NPROC+1
+    - lib/iov_iter: initialize "flags" in new pipe_buffer
+    - rlimit: Fix RLIMIT_NPROC enforcement failure caused by capability calls in
+      set_user
+    - ucounts: Move RLIMIT_NPROC handling after set_user
+    - net: sched: limit TC_ACT_REPEAT loops
+    - dmaengine: sh: rcar-dmac: Check for error num after setting mask
+    - dmaengine: stm32-dmamux: Fix PM disable depth imbalance in
+      stm32_dmamux_probe
+    - dmaengine: sh: rcar-dmac: Check for error num after dma_set_max_seg_size
+    - tests: fix idmapped mount_setattr test
+    - i2c: qcom-cci: don't delete an unregistered adapter
+    - i2c: qcom-cci: don't put a device tree node before i2c_add_adapter()
+    - dmaengine: ptdma: Fix the error handling path in pt_core_init()
+    - copy_process(): Move fd_install() out of sighand->siglock critical section
+    - scsi: qedi: Fix ABBA deadlock in qedi_process_tmf_resp() and
+      qedi_process_cmd_cleanup_resp()
+    - ice: enable parsing IPSEC SPI headers for RSS
+    - i2c: brcmstb: fix support for DSL and CM variants
+    - lockdep: Correct lock_classes index mapping
+    - Linux 5.15.25
+  * Jammy update: v5.15.24 upstream stable release (LP: #1963889)
+    - integrity: check the return value of audit_log_start()
+    - ima: fix reference leak in asymmetric_verify()
+    - ima: Remove ima_policy file before directory
+    - ima: Allow template selection with ima_template[_fmt]= after ima_hash=
+    - ima: Do not print policy rule with inactive LSM labels
+    - mmc: sdhci-of-esdhc: Check for error num after setting mask
+    - mmc: core: Wait for command setting 'Power Off Notification' bit to complete
+    - can: isotp: fix potential CAN frame reception race in isotp_rcv()
+    - can: isotp: fix error path in isotp_sendmsg() to unlock wait queue
+    - net: phy: marvell: Fix RGMII Tx/Rx delays setting in 88e1121-compatible PHYs
+    - net: phy: marvell: Fix MDI-x polarity setting in 88e1118-compatible PHYs
+    - NFS: Fix initialisation of nfs_client cl_flags field
+    - NFSD: Fix NFSv3 SETATTR/CREATE's handling of large file sizes
+    - NFSD: Fix ia_size underflow
+    - NFSD: Clamp WRITE offsets
+    - NFSD: Fix offset type in I/O trace points
+    - NFSD: Fix the behavior of READ near OFFSET_MAX
+    - thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume
+    - thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses
+    - thermal: int340x: Limit Kconfig to 64-bit
+    - thermal/drivers/int340x: Fix RFIM mailbox write commands
+    - tracing: Propagate is_signed to expression
+    - NFS: change nfs_access_get_cached to only report the mask
+    - NFSv4 only print the label when its queried
+    - nfs: nfs4clinet: check the return value of kstrdup()
+    - NFSv4.1: Fix uninitialised variable in devicenotify
+    - NFSv4 remove zero number of fs_locations entries error check
+    - NFSv4 store server support for fs_location attribute
+    - NFSv4.1 query for fs_location attr on a new file system
+    - NFSv4 expose nfs_parse_server_name function
+    - NFSv4 handle port presence in fs_location server string
+    - SUNRPC allow for unspecified transport time in rpc_clnt_add_xprt
+    - net/sunrpc: fix reference count leaks in rpc_sysfs_xprt_state_change
+    - sunrpc: Fix potential race conditions in rpc_sysfs_xprt_state_change()
+    - irqchip/realtek-rtl: Service all pending interrupts
+    - perf/x86/rapl: fix AMD event handling
+    - x86/perf: Avoid warning for Arch LBR without XSAVE
+    - sched: Avoid double preemption in __cond_resched_*lock*()
+    - drm/vc4: Fix deadlock on DSI device attach error
+    - drm: panel-orientation-quirks: Add quirk for the 1Netbook OneXPlayer
+    - net: sched: Clarify error message when qdisc kind is unknown
+    - powerpc/fixmap: Fix VM debug warning on unmap
+    - scsi: target: iscsi: Make sure the np under each tpg is unique
+    - scsi: ufs: ufshcd-pltfrm: Check the return value of devm_kstrdup()
+    - scsi: qedf: Add stag_work to all the vports
+    - scsi: qedf: Fix refcount issue when LOGO is received during TMF
+    - scsi: qedf: Change context reset messages to ratelimited
+    - scsi: pm8001: Fix bogus FW crash for maxcpus=1
+    - scsi: ufs: Use generic error code in ufshcd_set_dev_pwr_mode()
+    - scsi: ufs: Treat link loss as fatal error
+    - scsi: myrs: Fix crash in error case
+    - net: stmmac: reduce unnecessary wakeups from eee sw timer
+    - PM: hibernate: Remove register_nosave_region_late()
+    - drm/amd/display: Correct MPC split policy for DCN301
+    - usb: dwc2: gadget: don't try to disable ep0 in dwc2_hsotg_suspend
+    - perf: Always wake the parent event
+    - nvme-pci: add the IGNORE_DEV_SUBNQN quirk for Intel P4500/P4600 SSDs
+    - MIPS: Fix build error due to PTR used in more places
+    - net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
+    - KVM: eventfd: Fix false positive RCU usage warning
+    - KVM: nVMX: eVMCS: Filter out VM_EXIT_SAVE_VMX_PREEMPTION_TIMER
+    - KVM: nVMX: Also filter MSR_IA32_VMX_TRUE_PINBASED_CTLS when eVMCS
+    - KVM: SVM: Don't kill SEV guest if SMAP erratum triggers in usermode
+    - KVM: VMX: Set vmcs.PENDING_DBG.BS on #DB in STI/MOVSS blocking shadow
+    - KVM: x86: Report deprecated x87 features in supported CPUID
+    - riscv: fix build with binutils 2.38
+    - riscv: cpu-hotplug: clear cpu from numa map when teardown
+    - riscv: eliminate unreliable __builtin_frame_address(1)
+    - gfs2: Fix gfs2_release for non-writers regression
+    - ARM: dts: imx23-evk: Remove MX23_PAD_SSP1_DETECT from hog group
+    - ARM: dts: Fix boot regression on Skomer
+    - ARM: socfpga: fix missing RESET_CONTROLLER
+    - nvme-tcp: fix bogus request completion when failing to send AER
+    - ACPI/IORT: Check node revision for PMCG resources
+    - PM: s2idle: ACPI: Fix wakeup interrupts handling
+    - drm/amdgpu/display: change pipe policy for DCN 2.0
+    - drm/rockchip: vop: Correct RK3399 VOP register fields
+    - drm/i915: Allow !join_mbus cases for adlp+ dbuf configuration
+    - drm/i915: Populate pipe dbuf slices more accurately during readout
+    - ARM: dts: Fix timer regression for beagleboard revision c
+    - ARM: dts: meson: Fix the UART compatible strings
+    - ARM: dts: meson8: Fix the UART device-tree schema validation
+    - ARM: dts: meson8b: Fix the UART device-tree schema validation
+    - phy: broadcom: Kconfig: Fix PHY_BRCM_USB config option
+    - staging: fbtft: Fix error path in fbtft_driver_module_init()
+    - ARM: dts: imx6qdl-udoo: Properly describe the SD card detect
+    - phy: xilinx: zynqmp: Fix bus width setting for SGMII
+    - phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable()
+    - ARM: dts: imx7ulp: Fix 'assigned-clocks-parents' typo
+    - arm64: dts: imx8mq: fix mipi_csi bidirectional port numbers
+    - usb: f_fs: Fix use-after-free for epfile
+    - phy: dphy: Correct clk_pre parameter
+    - gpio: aggregator: Fix calling into sleeping GPIO controllers
+    - NFS: Don't overfill uncached readdir pages
+    - NFS: Don't skip directory entries when doing uncached readdir
+    - drm/vc4: hdmi: Allow DBLCLK modes even if horz timing is odd.
+    - misc: fastrpc: avoid double fput() on failed usercopy
+    - net: sparx5: Fix get_stat64 crash in tcpdump
+    - netfilter: ctnetlink: disable helper autoassign
+    - arm64: dts: meson-g12b-odroid-n2: fix typo 'dio2133'
+    - arm64: dts: meson-sm1-odroid: use correct enable-gpio pin for tf-io
+      regulator
+    - arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO domain for GPIOE_2
+    - arm64: dts: meson-sm1-odroid: fix boot loop after reboot
+    - ixgbevf: Require large buffers for build_skb on 82599VF
+    - drm/panel: simple: Assign data from panel_dpi_probe() correctly
+    - ACPI: PM: s2idle: Cancel wakeup before dispatching EC GPE
+    - gpiolib: Never return internal error codes to user space
+    - gpio: sifive: use the correct register to read output values
+    - fbcon: Avoid 'cap' set but not used warning
+    - bonding: pair enable_port with slave_arr_updates
+    - net: dsa: mv88e6xxx: don't use devres for mdiobus
+    - net: dsa: ar9331: register the mdiobus under devres
+    - net: dsa: bcm_sf2: don't use devres for mdiobus
+    - net: dsa: felix: don't use devres for mdiobus
+    - net: dsa: mt7530: fix kernel bug in mdiobus_free() when unbinding
+    - net: dsa: lantiq_gswip: don't use devres for mdiobus
+    - ipmr,ip6mr: acquire RTNL before calling ip[6]mr_free_table() on failure path
+    - nfp: flower: fix ida_idx not being released
+    - net: do not keep the dst cache when uncloning an skb dst and its metadata
+    - net: fix a memleak when uncloning an skb dst and its metadata
+    - veth: fix races around rq->rx_notify_masked
+    - net: mdio: aspeed: Add missing MODULE_DEVICE_TABLE
+    - tipc: rate limit warning for received illegal binding update
+    - net: amd-xgbe: disable interrupts during pci removal
+    - drm/amd/pm: fix hwmon node of power1_label create issue
+    - mptcp: netlink: process IPv6 addrs in creating listening sockets
+    - dpaa2-eth: unregister the netdev before disconnecting from the PHY
+    - ice: fix an error code in ice_cfg_phy_fec()
+    - ice: fix IPIP and SIT TSO offload
+    - ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
+    - ice: Avoid RTNL lock when re-creating auxiliary device
+    - net: mscc: ocelot: fix mutex lock error during ethtool stats read
+    - net: dsa: mv88e6xxx: fix use-after-free in mv88e6xxx_mdios_unregister
+    - vt_ioctl: fix array_index_nospec in vt_setactivate
+    - vt_ioctl: add array_index_nospec to VT_ACTIVATE
+    - n_tty: wake up poll(POLLRDNORM) on receiving data
+    - eeprom: ee1004: limit i2c reads to I2C_SMBUS_BLOCK_MAX
+    - usb: dwc2: drd: fix soft connect when gadget is unconfigured
+    - Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
+    - net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
+    - usb: ulpi: Move of_node_put to ulpi_dev_release
+    - usb: ulpi: Call of_node_put correctly
+    - usb: dwc3: gadget: Prevent core from processing stale TRBs
+    - usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
+    - USB: gadget: validate interface OS descriptor requests
+    - usb: gadget: rndis: check size of RNDIS_MSG_SET command
+    - usb: gadget: f_uac2: Define specific wTerminalType
+    - usb: raw-gadget: fix handling of dual-direction-capable endpoints
+    - USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
+    - USB: serial: option: add ZTE MF286D modem
+    - USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
+    - USB: serial: cp210x: add NCR Retail IO box id
+    - USB: serial: cp210x: add CPI Bulk Coin Recycler id
+    - speakup-dectlk: Restore pitch setting
+    - phy: ti: Fix missing sentinel for clk_div_table
+    - iio: buffer: Fix file related error handling in IIO_BUFFER_GET_FD_IOCTL
+    - mm: memcg: synchronize objcg lists with a dedicated spinlock
+    - seccomp: Invalidate seccomp mode to catch death failures
+    - signal: HANDLER_EXIT should clear SIGNAL_UNKILLABLE
+    - s390/cio: verify the driver availability for path_event call
+    - bus: mhi: pci_generic: Add mru_default for Foxconn SDX55
+    - bus: mhi: pci_generic: Add mru_default for Cinterion MV31-W
+    - hwmon: (dell-smm) Speed up setting of fan speed
+    - x86/sgx: Silence softlockup detection when releasing large enclaves
+    - Makefile.extrawarn: Move -Wunaligned-access to W=1
+    - scsi: lpfc: Remove NVMe support if kernel has NVME_FC disabled
+    - scsi: lpfc: Reduce log messages seen after firmware download
+    - MIPS: octeon: Fix missed PTR->PTR_WD conversion
+    - arm64: dts: imx8mq: fix lcdif port node
+    - perf: Fix list corruption in perf_cgroup_switch()
+    - iommu: Fix potential use-after-free during probe
+    - Linux 5.15.24
+  * Jammy update: v5.15.23 upstream stable release (LP: #1963888)
+    - moxart: fix potential use-after-free on remove path
+    - arm64: Add Cortex-A510 CPU part definition
+    - ksmbd: fix SMB 3.11 posix extension mount failure
+    - crypto: api - Move cryptomgr soft dependency into algapi
+    - Linux 5.15.23
+  * [22.04 FEAT] KVM: Enable storage key checking for intercepted instruction
+    handled by userspace (LP: #1933179)
+    - KVM: s390: gaccess: Refactor gpa and length calculation
+    - KVM: s390: gaccess: Refactor access address range check
+    - KVM: s390: gaccess: Cleanup access to guest pages
+    - s390/uaccess: introduce bit field for OAC specifier
+    - s390/uaccess: fix compile error
+    - s390/uaccess: Add copy_from/to_user_key functions
+    - KVM: s390: Honor storage keys when accessing guest memory
+    - KVM: s390: handle_tprot: Honor storage keys
+    - KVM: s390: selftests: Test TEST PROTECTION emulation
+    - KVM: s390: Add optional storage key checking to MEMOP IOCTL
+    - KVM: s390: Add vm IOCTL for key checked guest absolute memory access
+    - KVM: s390: Rename existing vcpu memop functions
+    - KVM: s390: Add capability for storage key extension of MEM_OP IOCTL
+    - KVM: s390: Update api documentation for memop ioctl
+    - KVM: s390: Clarify key argument for MEM_OP in api docs
+    - KVM: s390: Add missing vm MEM_OP size check
+  * CVE-2022-25636
+    - netfilter: nf_tables_offload: incorrect flow offload action array size
+  * ubuntu_kernel_selftests / ftrace:ftracetest do_softirq failure on Jammy
+    realtime (LP: #1959610)
+    - selftests/ftrace: Do not trace do_softirq because of PREEMPT_RT
+  * CVE-2022-0435
+    - tipc: improve size validations for received domain records
+  * CVE-2022-0516
+    - KVM: s390: Return error on SIDA memop on normal guest
+  * EDAC update for AMD Genoa support in 22.04 (LP: #1960362)
+    - EDAC: Add RDDR5 and LRDDR5 memory types
+    - EDAC/amd64: Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
+  * hwmon: k10temp updates for AMD Genoa in 22.04 (LP: #1960361)
+    - x86/amd_nb: Add AMD Family 19h Models (10h-1Fh) and (A0h-AFh) PCI IDs
+    - hwmon: (k10temp) Remove unused definitions
+    - hwmon: (k10temp) Support up to 12 CCDs on AMD Family of processors
+    - hwmon: (k10temp) Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
+  * [SRU][I/J/OEM-5.13/OEM-5.14] Add basic support of MT7922 (LP: #1958151)
+    - mt76: mt7921: Add mt7922 support
+    - mt76: mt7921: add support for PCIe ID 0x0608/0x0616
+    - mt76: mt7921: introduce 160 MHz channel bandwidth support
+  * Use EC GPE for s2idle wakeup on AMD platforms (LP: #1960771)
+    - ACPI: PM: Revert "Only mark EC GPE for wakeup on Intel systems"
+  * Update Broadcom Emulex FC HBA lpfc driver to 14.0.0.4 for Ubuntu 22.04
+    (LP: #1956982)
+    - scsi: lpfc: Change return code on I/Os received during link bounce
+    - scsi: lpfc: Fix NPIV port deletion crash
+    - scsi: lpfc: Adjust CMF total bytes and rxmonitor
+    - scsi: lpfc: Cap CMF read bytes to MBPI
+    - scsi: lpfc: Add additional debugfs support for CMF
+    - scsi: lpfc: Update lpfc version to 14.0.0.4
+  * Forward-port drm/i915 commits from oem-5.14 for Alder Lake S & P
+    (LP: #1960298)
+    - drm/i915/dmc: Update to DMC v2.12
+    - drm/i915/adlp/tc: Fix PHY connected check for Thunderbolt mode
+    - drm/i915/tc: Remove waiting for PHY complete during releasing ownership
+    - drm/i915/tc: Check for DP-alt, legacy sinks before taking PHY ownership
+    - drm/i915/tc: Add/use helpers to retrieve TypeC port properties
+    - drm/i915/tc: Don't keep legacy TypeC ports in connected state w/o a sink
+    - drm/i915/tc: Add a mode for the TypeC PHY's disconnected state
+    - drm/i915/tc: Refactor TC-cold block/unblock helpers
+    - drm/i915/tc: Avoid using legacy AUX PW in TBT mode
+    - drm/i915/icl/tc: Remove the ICL special casing during TC-cold blocking
+    - drm/i915/tc: Fix TypeC PHY connect/disconnect logic on ADL-P
+    - drm/i915/tc: Drop extra TC cold blocking from intel_tc_port_connected()
+    - drm/i915/tc: Fix system hang on ADL-P during TypeC PHY disconnect
+    - drm/i915/display/adlp: Disable underrun recovery
+    - drm/i915/adl_s: Remove require_force_probe protection
+    - drm/i915/adlp: Remove require_force_probe protection
+  * INVALID or PRIVATE BUG (LP: #1959735)
+    - KVM: s390: Simplify SIGP Set Arch handling
+    - KVM: s390: Add a routine for setting userspace CPU state
+  * Include the QCA WCN 6856 v2.1 support (LP: #1954938)
+    - SAUCE: ath11k: shrink TCSR read mask for WCN6855 hw2.1
+  * Jammy update: v5.15.22 upstream stable release (LP: #1960516)
+    - drm/i915: Disable DSB usage for now
+    - selinux: fix double free of cond_list on error paths
+    - audit: improve audit queue handling when "audit=1" on cmdline
+    - ipc/sem: do not sleep with a spin lock held
+    - spi: stm32-qspi: Update spi registering
+    - ASoC: hdmi-codec: Fix OOB memory accesses
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_volsw()
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_volsw_sx()
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_xr_sx()
+    - ALSA: usb-audio: Correct quirk for VF0770
+    - ALSA: hda: Fix UAF of leds class devs at unbinding
+    - ALSA: hda: realtek: Fix race at concurrent COEF updates
+    - ALSA: hda/realtek: Add quirk for ASUS GU603
+    - ALSA: hda/realtek: Add missing fixup-model entry for Gigabyte X570 ALC1220
+      quirks
+    - ALSA: hda/realtek: Fix silent output on Gigabyte X570S Aorus Master (newer
+      chipset)
+    - ALSA: hda/realtek: Fix silent output on Gigabyte X570 Aorus Xtreme after
+      reboot from Windows
+    - btrfs: don't start transaction for scrub if the fs is mounted read-only
+    - btrfs: fix deadlock between quota disable and qgroup rescan worker
+    - btrfs: fix use-after-free after failure to create a snapshot
+    - Revert "fs/9p: search open fids first"
+    - drm/nouveau: fix off by one in BIOS boundary checking
+    - drm/i915/adlp: Fix TypeC PHY-ready status readout
+    - drm/amd/pm: correct the MGpuFanBoost support for Beige Goby
+    - drm/amd/display: watermark latencies is not enough on DCN31
+    - drm/amd/display: Force link_rate as LINK_RATE_RBR2 for 2018 15" Apple Retina
+      panels
+    - nvme-fabrics: fix state check in nvmf_ctlr_matches_baseopts()
+    - mm/debug_vm_pgtable: remove pte entry from the page table
+    - mm/pgtable: define pte_index so that preprocessor could recognize it
+    - mm/kmemleak: avoid scanning potential huge holes
+    - block: bio-integrity: Advance seed correctly for larger interval sizes
+    - dma-buf: heaps: Fix potential spectre v1 gadget
+    - IB/hfi1: Fix AIP early init panic
+    - Revert "fbcon: Disable accelerated scrolling"
+    - fbcon: Add option to enable legacy hardware acceleration
+    - mptcp: fix msk traversal in mptcp_nl_cmd_set_flags()
+    - Revert "ASoC: mediatek: Check for error clk pointer"
+    - KVM: arm64: Avoid consuming a stale esr value when SError occur
+    - KVM: arm64: Stop handle_exit() from handling HVC twice when an SError occurs
+    - RDMA/cma: Use correct address when leaving multicast group
+    - RDMA/ucma: Protect mc during concurrent multicast leaves
+    - RDMA/siw: Fix refcounting leak in siw_create_qp()
+    - IB/rdmavt: Validate remote_addr during loopback atomic tests
+    - RDMA/siw: Fix broken RDMA Read Fence/Resume logic.
+    - RDMA/mlx4: Don't continue event handler after memory allocation failure
+    - ALSA: usb-audio: initialize variables that could ignore errors
+    - ALSA: hda: Fix signedness of sscanf() arguments
+    - ALSA: hda: Skip codec shutdown in case the codec is not registered
+    - iommu/vt-d: Fix potential memory leak in intel_setup_irq_remapping()
+    - iommu/amd: Fix loop timeout issue in iommu_ga_log_enable()
+    - spi: bcm-qspi: check for valid cs before applying chip select
+    - spi: mediatek: Avoid NULL pointer crash in interrupt
+    - spi: meson-spicc: add IRQ check in meson_spicc_probe
+    - spi: uniphier: fix reference count leak in uniphier_spi_probe()
+    - IB/hfi1: Fix tstats alloc and dealloc
+    - IB/cm: Release previously acquired reference counter in the cm_id_priv
+    - net: ieee802154: hwsim: Ensure proper channel selection at probe time
+    - net: ieee802154: mcr20a: Fix lifs/sifs periods
+    - net: ieee802154: ca8210: Stop leaking skb's
+    - netfilter: nft_reject_bridge: Fix for missing reply from prerouting
+    - net: ieee802154: Return meaningful error codes from the netlink helpers
+    - net/smc: Forward wakeup to smc socket waitqueue after fallback
+    - net: stmmac: dwmac-visconti: No change to ETHER_CLOCK_SEL for unexpected
+      speed request.
+    - net: stmmac: properly handle with runtime pm in stmmac_dvr_remove()
+    - net: macsec: Fix offload support for NETDEV_UNREGISTER event
+    - net: macsec: Verify that send_sci is on when setting Tx sci explicitly
+    - net: stmmac: dump gmac4 DMA registers correctly
+    - net: stmmac: ensure PTP time register reads are consistent
+    - drm/kmb: Fix for build errors with Warray-bounds
+    - drm/i915/overlay: Prevent divide by zero bugs in scaling
+    - drm/amd: avoid suspend on dGPUs w/ s2idle support when runtime PM enabled
+    - ASoC: fsl: Add missing error handling in pcm030_fabric_probe
+    - ASoC: xilinx: xlnx_formatter_pcm: Make buffer bytes multiple of period bytes
+    - ASoC: simple-card: fix probe failure on platform component
+    - ASoC: cpcap: Check for NULL pointer after calling of_get_child_by_name
+    - ASoC: max9759: fix underflow in speaker_gain_control_put()
+    - ASoC: codecs: wcd938x: fix incorrect used of portid
+    - ASoC: codecs: lpass-rx-macro: fix sidetone register offsets
+    - ASoC: codecs: wcd938x: fix return value of mixer put function
+    - pinctrl: sunxi: Fix H616 I2S3 pin data
+    - pinctrl: intel: Fix a glitch when updating IRQ flags on a preconfigured line
+    - pinctrl: intel: fix unexpected interrupt
+    - pinctrl: bcm2835: Fix a few error paths
+    - scsi: bnx2fc: Make bnx2fc_recv_frame() mp safe
+    - nfsd: nfsd4_setclientid_confirm mistakenly expires confirmed client.
+    - gve: fix the wrong AdminQ buffer queue index check
+    - bpf: Use VM_MAP instead of VM_ALLOC for ringbuf
+    - selftests/exec: Remove pipe from TEST_GEN_FILES
+    - selftests: futex: Use variable MAKE instead of make
+    - tools/resolve_btfids: Do not print any commands when building silently
+    - e1000e: Separate ADP board type from TGP
+    - rtc: cmos: Evaluate century appropriate
+    - kvm: add guest_state_{enter,exit}_irqoff()
+    - kvm/arm64: rework guest entry logic
+    - perf: Copy perf_event_attr::sig_data on modification
+    - perf stat: Fix display of grouped aliased events
+    - perf/x86/intel/pt: Fix crash with stop filters in single-range mode
+    - x86/perf: Default set FREEZE_ON_SMI for all
+    - EDAC/altera: Fix deferred probing
+    - EDAC/xgene: Fix deferred probing
+    - ext4: prevent used blocks from being allocated during fast commit replay
+    - ext4: modify the logic of ext4_mb_new_blocks_simple
+    - ext4: fix error handling in ext4_restore_inline_data()
+    - ext4: fix error handling in ext4_fc_record_modified_inode()
+    - ext4: fix incorrect type issue during replay_del_range
+    - net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY
+    - cgroup/cpuset: Fix "suspicious RCU usage" lockdep warning
+    - tools include UAPI: Sync sound/asound.h copy with the kernel sources
+    - gpio: idt3243x: Fix an ignored error return from platform_get_irq()
+    - gpio: mpc8xxx: Fix an ignored error return from platform_get_irq()
+    - selftests: nft_concat_range: add test for reload with no element add/del
+    - selftests: netfilter: check stateless nat udp checksum fixup
+    - Linux 5.15.22
+    - [Config] disable FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+  * Jammy update: v5.15.21 upstream stable release (LP: #1960515)
+    - Revert "drm/vc4: hdmi: Make sure the device is powered with CEC"
+    - Revert "drm/vc4: hdmi: Make sure the device is powered with CEC" again
+    - Linux 5.15.21
+  * Jammy update: v5.15.20 upstream stable release (LP: #1960509)
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Add handshake with the CSME to
+      support S0ix""
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Add polling mechanism to indicate
+      CSME DPG exit""
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Additional PHY power saving in S0ix""
+    - PCI: pciehp: Fix infinite loop in IRQ handler upon power fault
+    - selftests: mptcp: fix ipv6 routing setup
+    - net: ipa: use a bitmap for endpoint replenish_enabled
+    - net: ipa: prevent concurrent replenish
+    - drm/vc4: hdmi: Make sure the device is powered with CEC
+    - cgroup-v1: Require capabilities to set release_agent
+    - Revert "mm/gup: small refactoring: simplify try_grab_page()"
+    - ovl: don't fail copy up if no fileattr support on upper
+    - lockd: fix server crash on reboot of client holding lock
+    - lockd: fix failure to cleanup client locks
+    - net/mlx5e: IPsec: Fix tunnel mode crypto offload for non TCP/UDP traffic
+    - net/mlx5: Bridge, take rtnl lock in init error handler
+    - net/mlx5: Bridge, ensure dev_name is null-terminated
+    - net/mlx5e: Fix handling of wrong devices during bond netevent
+    - net/mlx5: Use del_timer_sync in fw reset flow of halting poll
+    - net/mlx5e: Fix module EEPROM query
+    - net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
+    - net/mlx5e: Don't treat small ceil values as unlimited in HTB offload
+    - net/mlx5: Bridge, Fix devlink deadlock on net namespace deletion
+    - net/mlx5: E-Switch, Fix uninitialized variable modact
+    - ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback
+    - i40e: Fix reset bw limit when DCB enabled with 1 TC
+    - i40e: Fix reset path while removing the driver
+    - net: amd-xgbe: ensure to reset the tx_timer_active flag
+    - net: amd-xgbe: Fix skb data length underflow
+    - fanotify: Fix stale file descriptor in copy_event_to_user()
+    - net: sched: fix use-after-free in tc_new_tfilter()
+    - rtnetlink: make sure to refresh master_dev/m_ops in __rtnl_newlink()
+    - cpuset: Fix the bug that subpart_cpus updated wrongly in update_cpumask()
+    - e1000e: Handshake with CSME starts from ADL platforms
+    - af_packet: fix data-race in packet_setsockopt / packet_setsockopt
+    - tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data()
+    - ovl: fix NULL pointer dereference in copy up warning
+    - Linux 5.15.20
+  * Miscellaneous Ubuntu changes
+    - [Packaging] use default zstd compression
+    - [Packaging] do not use compression for image packages
+    - [Packaging] use xz compression for ddebs
+    - [Config] upgrade debug symbols from DWARF4 to DWARF5
+    - SAUCE: Makefile: Remove inclusion of lbm header files
+    - SAUCE: Makefile: Fix compiler warnings
+    - SAUCE: AUFS
+    - SAUCE: aufs: switch to 64-bit ino_t for s390x
+    - [Config] set AUFS as disabled
+    - SAUCE: mt76: mt7921e: fix possible probe failure after reboot
+    - Remove ubuntu/hio driver
+    - SAUCE: ima_policy: fix test for empty rule set
+    - SAUCE: sfc: The size of the RX recycle ring should be more flexible
+    - [Config] MITIGATE_SPECTRE_BRANCH_HISTORY=y && HARDEN_BRANCH_HISTORY=y
+  * Miscellaneous upstream changes
+    - kbuild: Unify options for BTF generation for vmlinux and modules
+    - MAINTAINERS: Add scripts/pahole-flags.sh to BPF section
+    - kbuild: Add CONFIG_PAHOLE_VERSION
+    - scripts/pahole-flags.sh: Use pahole-version.sh
+    - lib/Kconfig.debug: Use CONFIG_PAHOLE_VERSION
+    - lib/Kconfig.debug: Allow BTF + DWARF5 with pahole 1.21+
+    - x86/sched: Decrease further the priorities of SMT siblings
+    - sched/topology: Introduce sched_group::flags
+    - sched/fair: Optimize checking for group_asym_packing
+    - sched/fair: Provide update_sg_lb_stats() with sched domain statistics
+    - sched/fair: Carve out logic to mark a group for asymmetric packing
+    - sched/fair: Consider SMT in ASYM_PACKING load balance
+    - Revert "UBUNTU: [Config] x86-64: SYSFB_SIMPLEFB=y"
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Thu, 21 Apr 2022 17:20:52 +0800
+
+linux-xilinx-zynqmp (5.15.0-1005.6) jammy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs from Analysis_14_APR_2022
+
+  * Miscellaneous upstream changes
+    - net: xilinx: TSN endpoint extension support
+    - dt-bindings: Add EP MCDMA related bindings
+    - net: xilinx: EP only data path change
+    - net: xilinx: Change TADMA from discrete to continuous
+    - net: xilinx: Add barriers to fix bootup, switch cam entry and qci issues
+    - net: xilinx: Add support for dynamic configuration of Layer 2 stream
+      identification
+    - net: xilinx: Simplify device reset sequence
+    - net: xilinx: Pass phy interface to of_phy_connect()
+    - net: xilinx: Fix ep ioctl
+    - net: xilinx: Move Xilinx TSN to staging
+    - xilinx: Add TSN configuration options to kernel defconfig
+    - xilinx: Enable ethernet configs relevant to SOM TSN apps.
+    - misc: xilinx-ai-engine: Null terminate local event sysfs buffer
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Fri, 15 Apr 2022 12:03:29 +0800
+
+linux-xilinx-zynqmp (5.15.0-1004.5) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1966944)
+    - [Config] Disable CONFIG_ASYNC_TX_DMA
+
+  * INVALID or PRIVATE BUG (LP: #1964909)
+    - [Config] Enable Mali kernel driver
+
+  * Miscellaneous upstream changes
+    - Import Mali source code
+    - Change Makefile to be compatible with Yocto
+    - staging: mali: r8p0-01rel0: Add the ZYNQ/ZYNQMP platform
+    - staging: mali: r8p0-01rel0: Remove unused trace macros
+    - staging: mali: r8p0-01rel0: Don't include mali_read_phys() for zynq/zynqmp
+    - linux/mali_kernel_linux.c: Handle clock when probed and removed
+    - arm.c: global variable dma_ops is removed from the kernel 4.7
+    - common/mali_pm.c: Add PM runtime barrier after removing suspend
+    - linux/mali_kernel_linux.c: Enable/disable clock for runtime resume/suspend
+    - linux: mali_memory_os_alloc: Remove __GFP_COLD
+    - linux: mali_memory_secure: Add header file dma-direct.h
+    - linux: mali_*timer: Get rid of init_timer
+    - fix-driver-failed-to-check-map-error
+    - mali_memory_secure: Kernel 5.0 onwards 'access_ok' API does not take 'type'
+      as input parameter
+    - Support for vm_insert_pfn deprecated from kernel 4.20
+    - Change return type to vm_fault_t for fault handler
+    - "get_monotonic_boottime(&ts)" deprecated from kernel 4.20 onwards
+    - Fix ioremap_nocache() deprecation in kernel 5.6
+    - Use updated timekeeping functions in kernel 5.6
+    - Set HAVE_UNLOCKED_IOCTL default to true
+    - Use PTR_ERR_OR_ZERO instead of PTR_RET
+
+  [ Ubuntu: 5.15.0-22.22 ]
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Wed, 13 Apr 2022 16:16:17 +0800
+
+linux-xilinx-zynqmp (5.15.0-1003.4) jammy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs from Analysis_29_MAR_200
+
+  * Miscellaneous upstream changes
+    - microblaze: Use simple memmove/memcpy implementation from lib/string.c
+    - microblaze: Do loop unrolling for optimized memset implemenation
+    - microblaze: Wire memblock_dump_all()
+    - microblaze: Add support for reserved memory defined by DT
+    - net: macb: In ZynqMP initialization make SGMII phy configuration optional
+    - drm: xlnx: sdi: Add extra check to get the correct timing table index
+    - net: xilinx: axiethernet: Change the link up sequence from Block lock to Rx
+      status and valid Rx code.
+    - v4l: xilinx: dprx: Add unplug handler function in work queue
+    - arm64: zynqmp: Add PHY description for SGMII on vck190 SC
+    - dt-bindings: display: xlnx: extract zynqmp dpaud setting to separate binding
+    - arm64: xilinx: dts: Move DP audio registers to separate node
+    - sound: soc: xilinx: Added 44.1k & 48k sample rate support for DP
+    - Revert "ARM: zynq: Fix nand partitions for zc770-xm011"
+    - misc: xilinx-ai-engine: log additional hardware info
+    - dma: xlnx: drv: Added failsafe code for mem2mem DMA channels init-deinit
+    - xlnx: drv: m2m: Fix SPDX license coding style
+    - mtd: spi-nor: Avoid updating the flash_info struct in dual and stacked modes
+    - media: v4l: Support 3 planar YUV444P 8bpc pixel format in contiguous memory
+    - v4l: xilinx: vip: Support for 3 planar YUV444 8bpc format in contiguous
+      memory
+    - dt-bindings: dma: xilinx_frmbuf: Add support for 3 planar YUV444P 8bpc
+    - dmaengine: xilinx: frmbuf: Add support for 3 planar YUV444P 8bpc
+    - media: v4l2-tpg: add support for new pixelformat V4L2_PIX_FMT_YUV444P
+    - dt-bindings: xilinx: Fix issues with dprxss dt binding yaml
+    - xilinx: Enabled framebuffer configurations in default configuration
+    - media: i2c: ap1302: Update the min values for ap1302 controls
+    - dt-bindings: remoteproc: Update lockstep/split R5 configuration values
+    - net: axienet: Fix warnings related to function prototype
+    - net: axienet: Fix missing kernel description warnings
+    - net: axienet: Add coding style related fixes
+    - net: macb: Fix lost RX packet wakeup race in NAPI receive
+    - clk: xilinx: vcu: don't set pll_ref as parent of VCU(enc/dec) clocks
+    - pwm: pwm-cadence: Handle pwm-cells through of_xlate
+    - dt-bindings: timer: Update pwm-cells value ranges
+    - drm: xlnx: dptx: Add audio codec driver support
+    - sound: soc: xilinx: Remove using hdmi_codec_driver
+    - dt-bindings: misc: xlnx_dpu: Add DPUCZDX8G v3.4 documentation
+    - misc: xlnx_dpu: Add Xilinx DPU IP driver for Vivado tool flow
+    - misc: xlnx_dpu: add helper function to dump all registers
+    - misc: xlnx_dpu: Add debugfs interface to export memory and regs
+    - lib/iov_iter: initialize "flags" in new pipe_buffer
+    - tipc: improve size validations for received domain records
+    - drm: xlnx: hdmi: Get maximum link rate and number of lanes supported by sink
+    - drm: xlnx: hdmi: Correct DDC write field logic
+    - drm: xlnx: hdmi: Update pixel max rate to support higher resolutions
+    - ASoC: xlnx: Remove unnecessary dependency
+    - drm: xlnx: Update DPTX kconfig setting
+    - spi: spi-cadence-quadspi: Fix ospi resume failures
+    - fpga: select FPGA_BRIDGE for 'Xilinx LogiCORE PR Decoupler' helper
+    - dt-bindings: can: xilinx_can: Convert Xilinx CAN binding to YAML
+    - dt: bindings: media: xilinx: Add device tree bindings for subset conv
+    - v4l: xilinx: axis-subsetconv: Add driver for axis subset converter
+    - arm64: xilinx: Enable Xilinx axi4s subset converter driver
+    - arm64: xilinx: Enable IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+    - arm64: xilinx: Enable PWM support
+    - arm64: versal: Enable SND drivers by default for versal
+    - drm: xlnx: Move SND_PCM_ELD selection under DRM_XLNX
+    - drm: xlnx: Update DSI-Tx Kconfig
+    - staging: uartlite-rs485: Initial commit to add drv
+    - staging: uartlite-rs485: Advertise RS485 CAP
+    - arm64: xilinx: Enable Uartlite Rs485
+    - misc: xilinx-ai-engine: Query AIE clock by name ID
+    - misc: xilinx-ai-engine: Fix clock frequency to QoS conversion
+    - can: xilinx_can: Add Transmitter delay compensation (TDC) feature support
+    - microblaze: Remove user exception calling
+    - drivers: misc: xilinx_tmr_manager.c: Add api for reset handler
+    - microblaze: add support for TMR MB manager recovery
+    - edac: xilinx: make event manager registration configurable
+    - mmc: sdhci-of-arasan: Fix SDx_BASECLK configuration issue
+    - mmc: sdhci-of-arasan: Add delay to reach card stable state
+    - drivers: soc: xilinx: Fix error message on SGI registration failure
+    - misc: xilinx-ai-engine: fix return for overlay use case
+    - sound: soc: xilinx: Correct channel status register value for 48k sampled
+      audio
+    - arm64: defconfig: Update kernel configuration to support dma-buf heaps
+    - dmaengine: xilinx: ps_pcie: Remove ZynqMP PS-PCIe End Point Driver
+    - firmware: xilinx: Used lower_32_bits and upper_32_bits
+    - crypto: xilinx: Add upstreamed SHA driver
+    - arm64: xilinx: Enable ARM_PMU by default
+    - net: macb: Add ethtool support to advertise WOL
+    - net: macb: Use pm_runtime_force_resume/suspend APIs in MDIO helper functions
+    - arm64: configs: xilinx: Enable PWM support
+    - Revert "net: macb: Use pm_runtime_force_resume/suspend APIs in MDIO helper
+      functions"
+    - dmaengine: xilinx: frmbuf: Corrected error checking condition in fid_err and
+      fid_out getter functions
+    - arm64: zynqmp: Comment sata phy setting for zcu102
+    - arm64: zynqmp: Add pwm-fan node and fix ttc0 pwm-cells property
+    - arm64: zynqmp: Add pwm-fan node and ttc0 pwm-cells property
+    - arm64: versal: Add support for sysmon SSIT
+    - arm64: versal: Update USB node handle from dwc3 to usb
+    - drivers: crypto: Return error code if data size is out of bounds
+    - arm64: zynqmp: Add power domain description for PL
+    - arm64: zynqmp: Add dmas, gpu, rtc, watchdogs and opp nodes for SOM
+    - net: xilinx: Correct register write values for cam read/write
+    - net: xilinx: Fix HW hang issue for accesses to KEY2 and TV1 registers
+    - net: xilinx: Add switch learning support in TSN driver
+    - net: xilinx: Add switch port state change support
+    - net: xilinx: Add port vlan membership support in PL TSN driver
+    - net: xilinx: Add per vlan HW learning support
+    - net: xilinx: Add native vlan support in PL TSN driver
+    - net: xilinx: Add support to read switch CAM entries
+    - net: xilinx: Change the name of cam add/del function
+    - net: xilinx: Enable ipv when qci isn't enabled.
+    - net: xilinx: Add support for tag/untag options in switch cam
+    - net: xilinx: Set default pcp value for egress queue 1
+    - dt-bindings: Add TADMA specific properties
+    - net: xilinx: Add TADMA driver support
+    - net: xilinx: Add a separate function to set mac address for ep
+    - net: xilinx: Access qbv registers only when Qbv is enabled
+    - net: xilinx: Free the reference to ep, when register_netdevice fails
+    - net: xilinx: Add switch device support
+    - dt-bindings: xilinx_tsn_switch: Document number of ports
+    - net: xilinx: Add default cam entries for Management queue
+    - net: xilinx: Change irq name with details
+    - net: xilinx: Modify CB and QCI ioctl api
+    - net: xilinx: TSN queue numbers
+    - net: xilinx: Add PTPv2 support
+    - net: xilinx: Add support for enabling preemption
+    - net: xilinx: Compile time pcp mapping
+    - net: xilinx: Add check for minimum number of MCDMA Rx queues
+    - dt-bindings: net: Add Xilinx TSN extended endpoint bindings
+    - USB: gadget: validate endpoint index for xilinx udc
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Wed, 06 Apr 2022 22:43:53 +0800
+
+linux-xilinx-zynqmp (5.15.0-1002.3) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1964056)
+    - [Config] Update configs
+
+  * Miscellaneous upstream changes
+    - mtd: tests: Fix eraseblock read speed miscalculation for lower partition
+      sizes
+    - net: axienet: Fix DMA memory error handling during initialization
+    - net: axienet: Handle dma mapping errors in TX datapath
+    - net: axienet: Handle dma mapping errors in RX datapath
+    - spi: spi-zynqmp-gqspi: direct read made word aligned
+    - drm: xlnx: pl_disp: Add condition check for VTC bridge
+    - spi: spi-zynqmp-gqspi: Update driver dependencies
+    - spi: spi-zynq-qspi: Add spi-mem to driver dependencies
+    - mtd: spi-nor: Enable 4byte opcode for Winbond w25h02jvt flash
+    - firmware: xilinx: fix build warnings
+    - v4l: xilinx: hdmirx: Fix reference clock based on TMDS clock ratio
+    - v4l: xilinx: hdmirx: Fix incorrect framerate size for pixel repeat cases
+    - firmware: xilinx: fix backward compatibility
+    - misc: xilinx-ai-engine: release lock before return
+    - misc: xilinx-ai-engine: add dev_gen description
+    - misc: xilinx-ai-engine: balance braces
+    - drm: xlnx: zynqmp_dpsub: Add 3 planar YUV444 10bpc format in contiguous
+      memory
+    - media: v4l: Support 3 planar YUV 444 10bpc pixel format in contiguous memory
+    - v4l: xilinx: vip: Support for 3 planar YUV444 10bpc format in contiguous
+      memory
+    - dmaengine: xilinx: Handle IRQ mapping errors
+    - dt-bindings: dma: xilinx_frmbuf: Add support for 3 planar YUV444 10bpc
+    - dmaengine: xilinx: frmbuf: Add support for 3 planar YUV444 10bpc
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Tue, 08 Mar 2022 14:42:09 +0800
+
+linux-xilinx-zynqmp (5.15.0-1001.2) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1960990)
+    - [Config] Update configs
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] use a private PPA for getabis
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Mon, 07 Mar 2022 20:26:07 +0800
+
+linux-xilinx-zynqmp (5.15.0-1000.1) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - [Packaging] update Ubuntu.md
+    - [Packaging] update update.conf
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs
+
+  * Miscellaneous upstream changes
+    - Add package
+    - firmware: xilinx: add register notifier in zynqmp firmware
+    - firmware: xilinx: export the feature check of zynqmp firmware
+    - firmware: xilinx: move supported api callback ids
+    - include: linux: firmware: Add header file with error events details
+    - drivers: soc: xilinx: add xilinx event management driver
+    - firmware: xilinx: instantiate xilinx event manager driver
+    - driver: soc: xilinx: register for power events in zynqmp power driver
+    - firmware: xilinx: Add shutdown/wakeup APIs
+    - firmware: xilinx: check return value of zynqmp_pm_get_api_version()
+    - firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration.
+    - firmware: xilinx: Add IOCTL support for AIE ISR Clear
+    - firmware: xilinx: provides support to access efuse
+    - firmware: xilinx: Added pm api functions for RSA and SHA
+    - firmware: xilinx: Adds new eemi call for reg access
+    - firmware: xilinx: Enable PM_IOCTL in debugfs
+    - firmware: xilinx: Add missing debug firmware interfaces
+    - firmware: xilinx: Add pm api function for PL readback
+    - firmware: xilinx: Add AFI ioctl support
+    - firmware: xilinx: Add ULPI reset support
+    - firmware: xilinx: Add zynqmp SGMII firmware support
+    - firmware: xilinx: Add qspi firmware interface
+    - firmware: xilinx: xilinx: Add IOCTL ids for probe counter
+    - firmware: xilinx: Add IOCTL for handling usb power requests
+    - firmware: xilinx: Add support for GET_LAST_RESET_REASON IOCTL
+    - xilinx: firmware: Add sysfs to get last reset reason
+    - firmware: xilinx: Use u32 for reset ID in reset APIs
+    - firmware: zynqmp: Use DEVICE_ATTR_* to create sysfs entry
+    - usb: dwc3: Add power management support in DWC3 Xilinx driver
+    - firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
+    - firmware: xilinx: Open MMIO read/write interface via debugfs
+    - firmware: xilinx: Add support for runtime features
+    - firmware: xilinx: Add sysfs support for feature config
+    - firmware: xilinx: Add support to get the image uid info
+    - firmware: xilinx: Add support to access BBRAM and volatile user keys
+    - firmware: xilinx: Update firmware call interface to support additional arg
+    - xilinx: Fix alignment issues
+    - firmware: xilinx: Add support for secure read/write ioctl interface
+    - firmware: xilinx: add support for sd/usb/gem config
+    - firmware: xilinx: Add OSPI Mux selection support
+    - phy: xilinx: zynqmp: Fix bus width setting for SGMII
+    - mtd: rawnand: Add jedec_id to struct onfi_params
+    - mtd: rawnand: pl353: Set the nand chip node as the flash node
+    - dt-bindings: gpio: Add gpio-slg7xl45106.yaml
+    - drivers: gpio: Add support for SLG7XL45106 I2C GPO expander
+    - microblaze: Use simple memset implemenation from lib/string.c
+    - clocksource: timer-cadence-ttc: Do not probe TTC device configured as PWM
+    - dt-bindings: timer: Update device tree bindings for cadence TTC PWM
+    - pwm: pwm-cadence: Add support for TTC PWM
+    - xen/pvcalls: frontend enable
+    - xen/pvcalls: change CONFIG_XEN_PVCALLS_FRONTEND to bool
+    - drivers: soc: xilinx: Call InitFinalize from late_initcall_sync instead of
+      probe
+    - net: macb: add support for mdio phy nodes
+    - dt-bindings: net: macb: update for partial store and forward
+    - net: macb: Add support for partial store and forward
+    - net: macb: PTP fixes
+    - net: macb: Add provision for queue tie off
+    - net: macb: Use WOL via ARP
+    - net: macb: Increment rx bd head after allocating skb and buffer
+    - net: macb: Process tx timestamp only on ptp packets
+    - net: macb: Disable macb pad and fcs for fragmented packets
+    - net: macb: Optimize reading HW timestamp
+    - dt-bindings: net: macb: Add GEM versal compatible string
+    - net: macb: Update tsu clk usage in runtime suspend/resume for Versal
+    - net: macb: Use queue disable instead of tieoff in Versal suspend
+    - net: macb: Increase halt timeout to accommodate 10Mbps link
+    - net: macb: Reset TX when TX halt times out
+    - net: macb: Reorder probe and fix exit path
+    - net: macb: Handle phy reset for PCS PMA IP
+    - net: macb: Align the dma and coherent dma masks
+    - net: macb: Kernel gives call trace during resume from Wake on Lan
+    - net: macb: Handle phy reset for PCS PMA IP
+    - net: macb: Move the phy re-init to phylink function instead of open
+    - dt-bindings: spi: cadence-quadspi: Add support for Xilinx Versal OSPI
+    - spi: cadence-quadspi: Add OSPI support for Xilinx Versal SoC
+    - spi: cadence-quadspi: Add Xilinx Versal external DMA support
+    - spi: cadence-quadspi: fix dma_unmap_single() call
+    - firmware: xilinx: Add tristate configurations
+    - spi: spi-cadence-quadspi: Add support for OSPI device reset
+    - spi: spi-cadence-quadspi: Add support for DDR PHY mode
+    - spi: spi-cadence-quadspi: Add support for odd byte count read/write in DDR
+      mode
+    - mtd: spi-nor: issi: Add support for is25wx256
+    - mtd: spi-nor: gigadevice: Add support for GD25LX256E
+    - mtd: spi-nor: micron-st: Add support for mt35xu01g flash
+    - spi: spi-cadence-quadspi: Add support for OSPI Macronix
+    - spi: spi-cadence-quadspi: Add Rx periodic Tuning support
+    - OF: DT-Overlay configfs interface (v8)
+    - OF: overlay: Perform RCU callback barrier before releasing overlay memory
+      resources
+    - fpga: Add firmware store function
+    - fpga: mgr: Adopted Encrypted BitStream loading support for Xilinx zynqmp
+    - fpga: fpga-mgr: Add readback support
+    - fpga: zynqmp-fpga: Add support for pl configuration readback
+    - fpga: mgr: Update the status for fpga-manager
+    - fpga: zynqmp-fpga: Adds status interface
+    - fpga: Adopted Authenticated BitStream loading support for Xilinx
+    - fpga: doc: Add binding doc for the afi config driver
+    - fpga: Add xilinx AFI config driver
+    - fpga: doc: Add binding doc for the afi config driver
+    - fpga: zynq: Add AFI config driver
+    - fpga: fpga-bridge: Add manual set option via sysfs
+    - fpga: support loading from a pre-allocated buffer
+    - fpga: add bindings document for secure flags
+    - fpga: mgr: Adds secure BitStream loading support
+    - fpga: versal: Use the scatterlist interface
+    - fpga: zynqmp: Use the scatterlist interface
+    - fpga: zynq: Fix incorrect variable type
+    - fpga: zynqmp: Initialized variables before using it
+    - fpga: region: Add fpga-region property 'power-domains'
+    - fpga: region: Adds runtime PM support
+    - fpga: mgr: Update the state to provide the exact error code
+    - fpga: fpga-mgr: fix for coding style issues
+    - fpga: fpga-mgr: Add missing kernel-doc description
+    - fpga: versal: Use tab instead of spaces for indentation
+    - firmware: xilinx: Update the zynqmp_pm_fpga_load() API
+    - firmware: xilinx: Add support to get the image meta-header info
+    - firmware: xilinx: Add TF_A_PM_REGISTER_SGI SMC call
+    - firmware: xilinx: Add IOCTL support for the AIE run time operations
+    - firmware: xilinx: Implemented pm API functions to get the xilfpga component
+      info
+    - firmware: xilinx: Add IOCTL support to query QoS
+    - firmware: zynqmp: Add support for secure_image
+    - firmware: xilinx: Add support for IOCTL and QUERY ID feature check
+    - firmware: xilinx: add new function for do_feature_check_call
+    - firmware: xilinx: always check API version for IOCTL/QUERY
+    - firmware: xilinx: Use proper indentation in kernel-doc
+    - fpga: zynqmp: Add feature-list validation check
+    - dt-bindings: Add dt bindings for flex noc Performance Monitor
+    - misc: xilinx_flex: Add support for the flex noc Performance Monitor
+    - Documentation: short descriptions for Flexnoc Performance Monitor driver
+    - dt-bindings: misc: Add dt bindings for traffic generator
+    - trafgen: xilinx: add axi traffic generator driver
+    - trafgen: Document sysfs entries
+    - i2c: cadence: Recover bus after controller reset
+    - i2c-cadence: Check the return value of pin-ctrl
+    - i2c: cadence: Handling Slave monitor mode
+    - dt-bindings: add documentation of xilinx clocking wizard
+    - clk: clocking-wizard: Add the clockwizard to clk directory
+    - clk: clocking-wizard: Rename nr-outputs to xlnx,nr-outputs
+    - clk: clocking-wizard: Fix the reconfig for 5.2
+    - clk: clocking-wizard: Update the compatible
+    - clocking-wizard: Support higher frequency accuracy
+    - clk: clocking-wizard: Fix coding style violations
+    - dt-binding: apm: Add the binding document for APM
+    - uio: uio_xilinx_apm: Add Xilinx AXI performance monitor driver
+    - clk: zynq: pll: Fix kernel-doc warnings
+    - clk: zynq: trivial warning fix
+    - clk: zynq: Update the parameters to zynq_clk_register_periph_clk
+    - arm: zynq: Suspend support
+    - rtc: zynqmp: Add calibration set and get support
+    - rtc: zynqmp: fix linking failure for ARCH arm
+    - i2c: xiic: Fix Tx Interrupt path for grouped messages
+    - i2c: xiic: Add standard mode support for > 255 byte read transfers
+    - i2c: xiic: Fix coding style issues
+    - i2c: xiic: Enter standard mode only for > 255 byte read transfers
+    - i2c: xiic: Correct the datatype for rx_watermark
+    - i2c: xiic: Fix Rx and Tx paths in standard mode repeated start
+    - i2c: xiic: Add wait for FIFO empty in send_tx
+    - i2c: xiic: Use 'nmsgs' variable instead of repeated_start
+    - i2c: xiic: Add smbus_block_read functionality
+    - i2c-xiic: return value of xiic_reinit
+    - i2c-xiic: Fix the type check for xiic_wakeup
+    - i2c: xiic: Switch to Xiic standard mode for i2c-read
+    - i2c: xiic: Remove interrupt enable/disable in Rx path
+    - i2c: xiic: Update compatible with new IP version
+    - i2c: xiic: Add SCL frequency configuration support
+    - dt-bindings: i2c: xiic: Add 'xlnx,axi-iic-2.1' to compatible
+    - dt-bindings: i2c: xiic: Add 'clock-frequency' property
+    - i2c: xiic: Correct the BNB interrupt enable sequence
+    - dt-bindings: edac: Add bindings for Xilinx ZynqMP OCM binding
+    - edac: zynqmp: Add EDAC support for ZynqMP OCM Controller
+    - serial-uartlite: Remove an un-necessary read of control register
+    - dmaengine: xilinx_dma: Fix kernel-doc warnings
+    - dmaengine: xilinx_dma: Implement error handling in xilinx_dma_child_probe()
+      API
+    - dt-bindings: dmaengine: Add binding for xilinx axidma test client
+    - dmaengine: xilinx: Add axidmatest test client code
+    - dt-bindings: dmaengine: Add binding for vdmatest client
+    - dmaengine: xilinx: Add vdmatest test client code
+    - dma: zynqmp_dma: Initialize descriptor list after freeing during reset
+    - dmaengine: zynqmp_dma: Typecast the variable to handle overflow
+    - dmaengine: zynqmp_dma: Typecast the variable with dma_addr_t to handle
+      overflow
+    - dmaengine: zynqmp_dma: Typecast with enum to fix the coverity warning
+    - dmaengine: zynqmp_dma: Add conditions for return value check
+    - microblaze: timer: Don't use cpu timer setting
+    - microblaze: timer: Separate clocksource timer from clockevent one
+    - microblaze: timer: Pass timer freq via parameter
+    - microblaze: timer: Squash clocksource code together
+    - microblaze: timer: Covert timer to use cpu hotplug
+    - microblaze: timer: Move irq code to clockevent function
+    - microblaze: timer: Create per cpu clockevent device
+    - microblaze: timer: Remove global variables
+    - microblaze: timer: Make sure that clockevent timer is initialized properly
+    - microblaze: timer: Group clockevent setting together
+    - microblaze: timer: Detect cpu_id from DT
+    - microblaze: timer: Change timer initialization setting
+    - microblaze: timer: Make timer SMP aware
+    - microblaze: timer: Add condition to check return value
+    - microblaze: timer: Fix incompatible parameters passed to the function
+    - dt-bindings: net: Add bindings documentation for Xilinx PCS/PMA PHY
+    - net: phy: Add support for xilinx SGMII and 1000BASE-X phys
+    - net: xilinx_phy: Add flag to reset after clock enable
+    - dt-bindings: net: Add binding documentation for axi emaclite
+    - net: emaclite: Fix coding style
+    - net: emaclite: Add variable and conditions to check the return value
+    - net: emaclite: Remove custom BUFFER_ALIGN macro
+    - net: emaclite: Remove advertising of 1G speed and auto negotiation
+    - xilinx: Update copyright text to correct format
+    - Revert "net: axienet: document axistream-connected attribute"
+    - dt-bindings: net: axienet: Add binding for 2.5G, 10G and usxgmii mac
+      variants
+    - dt-bindings: net: axienet: Update binding doc for 10G/25G MAC 1588
+    - dt-bindings: net: axienet: Add clock support
+    - dt-bindings: net: axienet: Add support for mcdma
+    - dt-bindings: Add devicetree documentation for TSN
+    - dt-bindings: Add devicetree documentation for ep
+    - dt-bindings: net: Add devicetree documentation for MRMAC
+    - Revert "net: axienet: make use of axistream-connected attribute optional"
+    - net: axienet: Add NAPI support
+    - net: axienet: Use barriers at relevant places
+    - net: axienet: Fix lost wake-up scenario in xmit
+    - net: axienet: Add support for non-processor mode
+    - net: axienet: Add support for config structure
+    - net: axienet: Add support for 2.5G MAC
+    - net: axienet: Add support for 10G MAC
+    - net: axienet: Add support for 10G/25G MAC
+    - net: axienet: Add support for 1588
+    - net: axienet: Add support for ZynqMP
+    - net: axienet: Adding highmem support
+    - net: axienet: Remove unnecessary phy defines
+    - net: axienet: Allow unaligned transfers
+    - net: axienet: Use ether_addr_copy()
+    - net: axienet: Fix coding style issues
+    - net: axienet: Fix issues when DRE is not enabled in the h/w
+    - net: axienet: Add clock support
+    - net: axienet: added multichannel DMA support
+    - net: xilinx: axiethernet: Add USXGMII support
+    - net: xilinx: axiethernet: Check for queue full in transmit path
+    - net: xilinx: axiethernet: Fix axiethernet register description
+    - net: xilinx: axiethernet: Fix crash in axienet_recv
+    - Revert "net: axienet: convert to phylink API"
+    - net: xilinx: Add support for PL TSN IP features
+    - net: xilinx: Add support for PL TSN endpoint interface
+    - net: xilinx: Add Qci support to the PL TSN IP driver
+    - net: xilinx: Add Support for CB/FRER feature of PL TSN IP
+    - net: xilinx: Add support for Qbu/br feature of PL TSN IP
+    - net: xilinx: axiethernet: Fix swiotlb buffer full error
+    - net: xilinx: axiethernet: Pass phy interface to of_phy_connect()
+    - net: xilinx: Use prandom with range to avoid corner cases
+    - net: xilinx: XXV Ethernet HW timestamp fixes
+    - net: xilinx: Add MRMAC support
+    - net: xilinx: Add HW timestamping support for MRMAC
+    - net: xilinx: Add missing kernel-doc descriptions
+    - net: xilinx: Fix indentation issues
+    - net: xilinx: axiethernet: Add check for transmit data FIFO vacancy
+    - net: xilinx: Check if dma_map_single returned a valid address.
+    - net: xilinx: Refactor TSN functions into xilinx_tsn_ip.c
+    - net: xilinx: Add a separate mcdma probe function for TSN IP
+    - net: xilinx: Add a master xmit function for TSN packets.
+    - net: xilinx: Add MCDMA management channel support
+    - net: xilinx: Access qdv address and associated properties separately
+    - net: xilinx: Cleanup xilinx_tsn_shaper.* files
+    - net: xilinx: axiethernet: Remove the NULL assigning to a pointer
+    - net: xilinx: axiethernet: Fix the use of uninitialized variable
+    - net: xilinx: axiethernet: Add check to overcome NULL dereference warning
+    - net: xilinx: axiethernet: Fix indentation warnings
+    - net: xilinx: axiethernet: Replace the value with enum
+    - net: xilinx: axiethernet: Add condition to check the return value
+    - net: xilinx: axiethernet: Add variables and conditions to check return value
+    - net: xilinx: axiethernet: Reduce the width of variable to handle overflow
+    - net: xilinx: axiethernet: Enable dynamic MDIO MDC
+    - net: xilinx: GT reset updates for 2020.2
+    - net: xilinx: Add supported_coalesce_params to fix axienet on 5.10
+    - net: xilinx: Update MRMAC config structure with PTP command length
+    - net: xilinx: Handle TX TS FIFO timeout error
+    - net: xilinx: MRMAC TX CMD FIFO update
+    - net: xilinx: Add one step 1588 support for MRMAC
+    - net: axienet: Add one step PDelay support
+    - net: axienet: MRMAC reset sequence fixes
+    - net: xilinx: axiethernet: Fix compilation error when HW timestamp is enabled
+    - net: xilinx: Ethtool statistics support
+    - net: xilinx: axiethernet: Correct phy-mode comparison logic in _probe()
+    - net: xilinx: In MCMDA designs fix crash on ifconfig up
+    - net: xilinx: fix compile warning due to typecheck
+    - net: xilinx: axiethernet: Pass correct phy interface to of_phy_connect()
+    - net: axienet: Add GT reset status check for XXV new IP version
+    - dt-bindings: nvmem: Added efuse nodes
+    - nvmem: zynqmp: Added support to access efuse
+    - nvmem: zynqmp: Removed \r format specifier for prints.
+    - nvmem: zynqmp: Add support to PUF eFuses programming for User data
+    - nvmem: zynqmp: Replace ENOTSUPP by EOPNOTSUPP
+    - nvmem: zynqmp-nvmem: Fix passing incompatible parameters
+    - nvmem: zynqmp_nvmem: Fix zynqmp_nvmem_read() parameter alignment
+    - dt-bindings: Convert Xilinx watchdog bindings to json-schema
+    - watchdog: of_xilinx_wdt: Initialize watchdog via data structure
+    - watchdog: of_xilinx_wdt: Introduce wdttype enum for identification
+    - watchdog: of_xilinx_wdt: Add Versal support
+    - watchdog: of_xilinx_wdt: Wire setting up timeout via module parameter/DT
+    - watchdog: of_xilinx_wdt: Use a proper variable to handle overflow
+    - watchdog: of_xilinx_wdt: Add Versal Window watchdog support
+    - dt-bindings: serial: pl011: Add 'arm,xlnx-uart'
+    - serial: pl011: Add support for Xilinx Uart
+    - pinctrl: zynq: use module_platform_driver to simplify the code
+    - can: xilinx_can: Add check for NAPI Poll function
+    - can: xilinx_can: Remove repeated work the from kernel-doc
+    - clk: zynqmp: Add a check for NULL pointer
+    - clk: zynqmp: make bestdiv unsigned
+    - clk: zynqmp: Fix stack-out-of-bounds in strncpy`
+    - xilinx: Update copyright text to correct format
+    - tty: xilinx_uartps: Check the clk_enable return value
+    - tty: xilinx_uartps: Add check for runtime_get_sync calls
+    - tty: xilinx_uartps: Check clk_enable return type
+    - tty: xilinx_uartps: Make the timeout unsigned
+    - serial: uartps: Change uart ID port allocation
+    - serial: uartps: Fix the ignore_status
+    - serial: uartps: Prevent writes when the controller is disabled
+    - serial: uartps: Fix stuck ISR if RX disabled with non-empty FIFO
+    - PCI: xilinx-nwl: Fix coding style violations
+    - PCI: XDMA PL PCIe: Adding device tree binding for XDMA PL PCIe
+    - PCI: XDMA PL PCIe: Adding XDMA PL PCIe Root Port
+    - dt-bindings: irqchip: Add Xilinx Interrupt Controller bindings
+    - irqchip: xilinx: Make per cpu primary controller entries
+    - irqchip: xilinx: Enable generic irq multi handler
+    - irqchip: xilinx: Use handle_domain_irq()
+    - irqchip: xilinx: Move early initialization to own function
+    - irqchip: xilinx: Add support for sw interrupts
+    - irqchip: xilinx: Support only LE/BE irqc by the same driver
+    - irqchip: xilinx: Rename root_domain just to domain
+    - irqchip: xilinx: Add support for cpu hotplug
+    - irqchip: xilinx: Add support for Microblaze SMP
+    - irqchip: xilinx: Change level for cpu-id warning
+    - irqchip: xilinx: Avoid __init macro usage for xilinx_intc_of_init
+    - irqchip: xilinx: Add support to remove Xilinx INTC irqchip driver module
+    - irqchip: xilinx: Add support to remove the Xilinx INTC driver module
+    - synopsys: edac: Fix the issue in reporting of the error count
+    - dt-bindings: usb: Add clock support for udc-xilinx
+    - dt-bindings: udc-xilinx: Fix coding style in binding doc
+    - usb: gadget: udc-xilinx: Add clock support
+    - usb: xilinx: Add suspend resume support
+    - usb: phy: Add platform driver support for ULPI phys
+    - usb: gadget: udc: udc-xilinx: Add identifier to read_fn function arg
+    - usb: host: ehci-xilinx: modified driver to resolve formatting warnings
+    - usb: host: ehci-xilinx: Resolve kernel-doc Warnings
+    - usb: host: xhci: plat: add support for otg_set_host() call
+    - usb: host: xhci: add support for Light Reset for DWC3 DRD
+    - usb: xhci: Add workaround for fixing ep stream ring hang issue
+    - usb: uas: Add workaround for DATA IN urb's returned with status -EAGAIN
+    - uas: Add US_FL_NO_ATA_1X for linux tcm_usb_gadget
+    - usb: gadget: f_tcm: adjust write length with max packet size
+    - usb: gadget: f_tcm: comp_descriptor workaround during SS gadget
+    - usb: gadget: f_tcm: queue multiple commands request
+    - usb: gadget: f_tcm: add TARGET_SCF_ACK_KREF flag in BOT
+    - usb: gadget: f_tcm: support to set maxburst through configfs
+    - usb: function: f_tcm: Add support for getting alt interface number
+    - usb: xhci-plat: Add remote wakeup support
+    - usb: gadget: uvc_video: unlock before submitting a request to ep
+    - usb: xhci: wait for atleast 1ms after exiting U3
+    - usb: host: xhci: Add xhci_hcd to xhci_ring for use in
+      stream_timeout_function
+    - usb: gadget: send usb_gadget as an argument in get_config_params
+    - usb: chipidea: Add support for VBUS control with PHY
+    - usb: chipidea: Use usb2 phy for Zynq platform
+    - usb: chipidea: Check usb_phy exists before using it
+    - usb: gadget: udc: Remove useless variable assignment in xudc_read_fifo()
+    - usb: gadget: udc: Add return value error handling of function
+    - usb: chipidea: Fix return value handling
+    - usb: chipidea: core: Add return value function check
+    - usb: dwc3: gadget: Add hibernation support when operating in gadget mode
+    - usb: dwc3: core: Add regulator calls for communicating with dwc3 PMU
+    - usb: dwc3: gadget: add support for OTG in gadget framework
+    - usb: dwc3: hibernation: fix scratch buffer allocation
+    - dwc3: core: Enable GUCTL1 chicken bit 10 for fixing crc error after resume
+      bug
+    - dwc3: core: Enable GUCTL1 chicken bit 9 for correcting Inter Packet
+      Delay(IPD)
+    - usb: Add quirk for enabling workaround for BULK IN streams
+    - usb: dwc3: of-simple: Enable CCI support in dwc3 driver
+    - usb: dwc3: update GFLADJ_REFCLK_FLADJ in dwc3_frame_length_adjustment
+    - usb: dwc3: don't setup event buffers when operating in host mode
+    - usb: dwc3: Fix the logic for allocating and setting scratchpad buffers
+    - usb: dwc3: add support for enabling/disabling hibernation dynamically
+    - usb: dwc3: Fix the broken suspend/resume functionality in dwc3
+    - usb: dwc3: Correct usb dma mask for making SMMU work in device mode
+    - usb: dwc3: gadget: ISOC transfers should be stopped before starting a
+      transfer
+    - usb: dwc3: otg: fix broken OTG HNP feature
+    - usb: dwc3: Check for IOC/LST bit in both event->status and TRB->ctrl fields
+    - usb: dwc3: gadget: Don't kick transfer if LST or SHORT bits are set
+    - usb: dwc3: otg: Update Kconfig and Makefile for enabling OTG
+    - usb: dwc3: otg: add support for OTG in DWC3 host driver
+    - usb: dwc3: retain resource index for unforced stops
+    - usb: dwc3: otg: fix the function call used to get otg descriptor
+    - usb: dwc3: otg: remove otg static export warning
+    - usb: dwc3: use proper typecast to handle overflow
+    - usb: dwc3: Initialized variable with a proper value
+    - usb: dwc3: otg: Enable OTG support in dwc3-core driver
+    - usb: dwc3: use PROPERTY_ENTRY_BOOL to initialize property entries
+    - usb: dwc3: Implement stream transfer timeout
+    - usb: dwc3: Enable Xilinx platform only when Regulator is enabled
+    - dt-bindings: gpio: zynqmp: Add binding documentation for modepin
+    - gpio: modepin: Add driver support for modepin GPIO controller
+    - usb: dwc3: xilinx: Add gpio-reset support
+    - usb: dwc3: xilinx: Register drvdata before registering regulator
+    - usb: dwc3: xilinx: Add support for controller power state for host mode
+    - usb: dwc3: xilinx: fixed dwc3-xilinx driver warnings
+    - usb: chipidea: udc: Add xilinx revision support
+    - usb: dwc3: xilinx: Handle dr_mode setting from DT properly
+    - usb: dwc3: gadget: Add new platform_data.h file
+    - usb: dwc3: Fix OTG driver to work with v5.10 kernel
+    - usb: gadget: webcam: Add support for Full HD and 4K UHD Raw Video Formats
+    - usb: dwc3: xilinx: Handle USB3 PHY initialization properly
+    - usb: dwc3: xilinx: enable D3 power state entry feature
+    - usb: dwc3: core: scratchpad buffers allocation handling in host mode
+    - Revert "usb: function: f_tcm: Add support for getting alt interface number"
+    - usb: dwc3: handle usb2.0 gadget mode early hibernation event occurrence
+    - usb: chipidea: udc: make controller hardware endpoint primed
+    - usb: dwc3: Fixed common regulator for multiple controller instance
+    - usb: dwc3: xilinx: fix error handling for reset-gpio
+    - usb: dwc3: xilinx: fix reset-gpio logic
+    - usb: dwc3: core: Update REFCLK_FLADJ for frame length adjustment
+    - usb: dwc3: core: add PM_SLEEP kernel config check
+    - usb: dwc3: gadget: disable hibernation interrupt on gadget enumeration
+    - usb: dwc3: gadget: Increase timeout for CmdAct cleared by device controller
+    - dt-bindings: usb: dwc3: Add interrupt-names to include hibernation interrupt
+    - dt-bindings: usb: dwc3-xilinx: Convert USB DWC3 bindings
+    - Bluetooth: hci_ll: Extend timeout between start and communication
+    - uio: Add dma-buf import ioctls
+    - apf: Add kernel modules to the kernel
+    - uio: rename uio.c -> uio_core.c & unify into uio.ko
+    - microblaze: Swap location of bss and INIT_RAM_FS
+    - microblaze: Change TLB mapping and free space allocation
+    - microblaze: Fix message about compiled-in FDT location
+    - microblaze: Permit pcibios_set_master override
+    - microblaze: pci: Support generic Xilinx AXI PCIe Host Bridge IP driver
+    - dt-bindings: ARM: zynq: Add DT binding for eFuse controller
+    - ARM: zynq: Add support for Zynq-7000S devices
+    - ARM: zynq: Fix prefetch option
+    - zynq: slcr: Introduce new get_ocm_config()
+    - zynq: Add OCM driver
+    - Xilinx: ARM: Devcfg and SLCR drivers updated to support reconfiguration.
+    - dt-bindings: Add doc for xilinx fclk
+    - staging: fclk: Enable pl clock with sysfs entry for set_rate
+    - irqchip: gic: Add remoteproc changes to the driver
+    - watchdog: of_xilinx_wdt: Used dev_dbg()
+    - i2c: mux: pca954x: write to mux channel always
+    - dt-bindings: Add binding for IDT 8T49N24x UFT
+    - clk: Add ccf driver for IDT 8T49N24x UFT
+    - zynqmp: firmware: Adds a driver for loading secure partition from Linux
+    - dt-bindings: pmbus: Add tps544 bindings
+    - pmbus: Add new tps544 power regulator driver
+    - dt-bindings: crypto: Added binding docs for Xilinx ZynqMP SHA3 H/W
+      accelerator
+    - crypto: zynqmp-sha: Adopted SHA3 support for ZynqMP Soc
+    - dt-bindings: crypto: Added binding docs for Xilinx ZynqMP RSA H/W
+      accelerator
+    - crypto: zynqmp-rsa: Adopted RSA support for ZynqMP SoC
+    - phy: dp83867: Add support for SGMII
+    - include: dt-bindings: Add mscc-vsc8531 RGMII clock delay definitions
+    - dt-bindings: mscc: Add RGMII RX and TX delay tuning
+    - phy: mscc: Add support for VSC8531_02 with RGMII tuning
+    - dt-bindings: clock: Adding si5324 bindings
+    - clk: Adding Silicon labs si5324 clock driver
+    - edac: add support for ARM PL310 L2 cache parity
+    - dt-bindings: edac: Add bindings for ZynqMP OCM Controller
+    - edac: zynqmp: Add EDAC support for ZynqMP OCM Controller
+    - dt-bindings: edac: Add bindings for cortex_arm64
+    - EDAC: Add ARM64 EDAC
+    - edac: Add documentation for cortexa53 edac sysfs
+    - edac: Add sysfs entries for cortex arm64
+    - arm64: zynqmp: Change Kconfig dependency for cortexa53 edac
+    - drivers: ata: Add CCI support for SATA if CCI is enabled
+    - samples: xilinx_apm: Add sample application for xilinx_apm
+    - xilinx: Update MAINTAINERS fragment
+    - staging: Add xroeframer driver
+    - staging: xroetrafficgen: initial commit of roe traffic generator driver
+    - mtd: Expand the ecc placement locations to 1260
+    - dt-bindings: power: Add versal power domain bindings
+    - dt-bindings: pci: ZYNQMP PS PCIe Driver Root DMA dt bindings
+    - PCI: ZYNQMP EP driver: Adding support for ZynqMP ep driver
+    - PCI: ZYNQMP EP client driver: Adding support for ZynqMP dma test client
+    - dt-bindings: misc: Add documentation for jesd204b
+    - dt-bindings: misc: Add bindings for JESD phy
+    - misc: jesd204b: Add driver for Xilinx jesd204b
+    - mtd: fixing CFI for Numonyx CFI bug
+    - microblaze: Define SMP safe bit operations
+    - microblaze: Make cpuinfo structure SMP aware
+    - microblaze: Add SMP implementation of xchg and cmpxchg
+    - microblaze: Remove disabling IRQ while pte_update() run
+    - microblaze: Implement architecture spinlock
+    - microblaze: Do atomic operations by using exclusive
+    - microblaze: Prepare entry.S for SMP implementation
+    - microblaze: Rework mmu context management to prepare
+    - microblaze: Enable experimental SMP functionality
+    - dt-bindings: xilinx: Document new evaluation boards
+    - clk: idt: Fix i2cwritebulk() failure
+    - dt-bindings: Add versal clocking wizard
+    - clocking-wizard: Add versal clocking wizard support
+    - Revert "net: phy: ensure phylib state machine is stopped after calling
+      phy_stop"
+    - Revert "net: phy: call state machine synchronously in phy_stop"
+    - dt-bindings: usb: host: ehci-xilinx: Add binding doc
+    - xilinx: Add a github template telling people to not use pull requests there
+    - dt-binding: soc: xilinx: ai-engine: Add new AI engine binding
+    - dt-bindings: soc: xilinx: ai-engine-npi: Add the binding for AIE NPI
+    - misc: ai-engine: Move AI engine reg access to kernel
+    - ARM: zynq: Fix spurious BUG with old DT
+    - spi: spi-cadence: Fix mixed_enum_type coverity warning
+    - spi: spi-cadence: Fix uninit_use coverity warning
+    - dt-bindings: edac: Add bindings for Xilinx Versal EDAC for DDRMC
+    - edac: xilinx: Added EDAC support for Xilinx DDR controller
+    - dt-bindings: Add devicetree documentation for Xilinx PTP timer
+    - ptp: Add Xilinx PTP timer driver
+    - dt-bindings: serial: Add xilinx compatible
+    - i2c-cadence: Replace the value with enum
+    - dmaengine: pl330: Typecast with enum to fix the coverity warning
+    - arm: zynq: delete AFLAGS_suspend.o to fix compile warning
+    - dt-bindings: soc: xilinx: Add the dt binding for AI engine
+    - uio: Add the UIO driver for AI engine
+    - irqchip: gic: Add changes to handle SGI for Zynq Remoteproc driver
+    - pmbus: tps544: adapt for updated pmbus interfaces
+    - crypto: xilinx: zynqmp-aes: Add skcipher based AES driver
+    - dt-bindings: ptp: xilinx: Update new compatible string
+    - ptp: Add support for port offset registers
+    - crypto: xilinx: Drop COMPILE_TEST for CRYPTO_DEV_ZYNQMP_SHA3
+    - clk: si5324: fix linking failure for ARCH arm
+    - include: xilinx_phy: Add Copyright and License
+    - xen: add support for initializing xenstore later as HVM domain
+    - uartlite: Update the default for the parameter
+    - firmware: xilinx: Remove kernel-doc marking instead of regular comment
+    - firmware: xilinx: sync firmware pm_query_id entries with PLM query id
+      entries
+    - firmware: zynqmp: Add Node IDs in xlnx-zynqmp.h
+    - soc: xilinx: vcu: Export functions to obtain logicore settings
+    - clk: xilinx: vcu: Update vcu init/reset sequence
+    - clk: xilinx: vcu: disable aclk incase of probe failure
+    - clk: xilinx: vcu: Populate children node
+    - watchdog: of_xilinx_wdt: use wdd->parent in print
+    - dt-bindings: serial: uartlite: Convert uartlite to json-schema
+    - dt-bindings: clk: xlnx: move xlnx_vcu dt-binding to clk from soc
+    - dt-bindings: clk: xlnx: Update VCU bindings for vcu reset pin
+    - dt-bindings: clock: versal: Remove alt_ref_clk from clock source
+    - arm64: zynqmp: Add Xilinx SHA3 node
+    - arm64: zynqmp: Add support for ZynqMP RSA H/W accelerator
+    - dt-bindings: zynqmp: add RPU nodes
+    - dt-bindings: zynqmp: Add new PD_PL macro
+    - mtd: cfi: Add macro for Winbond NOR flashes
+    - firmware: zynqmp: Add sysfs entry for runtime features
+    - arm: zynq: add "-march=armv7-a" to AFLAGS
+    - arm: zynq: don't remove -march=armv6k from KBUILD_AFLAGS
+    - dt-bindings: usb: misc: Add binding for Microchip usb5744 hub
+    - usb: misc: usb5744: add support for USB hub controller
+    - dt-bindings: usb: misc: Add binding for Microchip usb2244 Controller
+    - usb: misc: usb2244: add support for USB2 ultra fast sd controller
+    - dt-bindings: Add Xilinx AMS binding documentation
+    - iio: adc: Add Xilinx AMS driver
+    - dt-bindings: iio: xilinx: Add Documentation for Sysmon
+    - iio: versal-sysmon: add driver for Versal Sysmon
+    - dt-bindings: gpio: zynq: Add all the supported compatibles
+    - dt-bindings: iio: adc: Add ti,ina260.yaml
+    - drivers: iio: Add support for TI INA260 power monitors
+    - iio: adc: versal-sysmon: Add runtime resume function for sysmon
+    - dt-bindings: nvmem: Added nodes for BBRAM and volatile user keys
+    - nvmem: Add driver for BBRAM and volatile user keys access
+    - remoteproc: Add support for peek from remote and acking kick from remote
+    - dt-bindings: Add Zynq remoteproc binding
+    - remoteproc: Add support for AMP on Zynq platform
+    - dt-bindings: remoteproc: Add documentation for ZynqMP R5 rproc bindings
+    - remoteproc: Add initial zynqmp R5 remoteproc driver
+    - dt: bindings: sound: Add DT bindings for Xilinx ZynqMP DP audio
+    - sound: soc: xilinx: Add ZynqMP DP subsystem audio drivers
+    - dt-bindings: ASoC: xlnx-v-uhdsdi-audio: document sdi audio bindings
+    - AsoC: xlnx: add platform driver to support SDI audio
+    - dt-bindings: ASoC: Document audio formatter bindings for xlnx,audio-
+      formatter
+    - ASoC: xlnx: add pcm formatter platform driver
+    - ASoC: xlnx: add PL sound card support
+    - dt-bindings: ASoC: xlnx,spdif: Document spdif bindings
+    - ASoC: xlnx: add SPDIF audio driver
+    - ASoC: xlnx,i2s: dt-bindings: add reference to audio formatter
+    - ASoC: xlnx: change I2S driver data
+    - drm: drm_fourcc: Introduce macro-pixel info to drm_format_info
+    - drm: fourcc: Add drm_format_plane_width_bytes()
+    - drm: drm_fourcc: Add new formats for Xilinx IPs
+    - drm: fourcc: Add new formats needed by Xilinx IP
+    - drm: drm_fourcc: Correct the DRM YUV444 10bpc
+    - uapi: drm: Add AVUY fourcc
+    - drm: Add new flags for interlaced alternate fields
+    - uapi: media: New fourcc codes needed by Xilinx Video IP
+    - media: Add documentation for YUV420 bus format
+    - dt-bindings: dmaengine: xilinx_frmbuf: Video Framebuffer IP
+    - dmaengine: xilinx_frmbuf: New driver for Video Framebuffer IP
+    - drm: panel: Added timing for AUO B101UAN01 display panel
+    - media: entity: Add has_route entity operation
+    - media: entity: Add media_entity_has_route() function
+    - v4l: subdev: Add [GS]_ROUTING subdev ioctls and operations
+    - v4l: Add RGB 8:8:8 media bus format on 24 and 32 bit busses
+    - v4l: Add VUY8 24 bits bus format
+    - uvcvideo: Xilinx: Bump up URBS and MAX_PACKETS
+    - v4l: xilinx: Kconfig: Add missing DMADEVICES dependencies
+    - media: xilinx: Ensure Video Framebuffer selected by Kconfig
+    - v4l: xilinx: Add Video Remapper driver
+    - media: xilinx: Add Color Filter Array (CFA) driver
+    - media: xilinx: Add Chroma Resampler (CRESAMPLE) driver
+    - media: xilinx: Add RGB to YUV (RGB2YUV) driver
+    - media: xilinx: Add Scaler driver (SCALER) driver
+    - media: xilinx: Add AXI4 stream switch driver
+    - media: xilinx: Add HLS core driver
+    - media: xilinx: Integrate TPG v7 support
+    - media: xilinx: tpg: Block comments
+    - media: xilinx: Refactor VTC configuration code
+    - media: xilinx: vip: Add the pixel format for RGB24
+    - v4l: xilinx: dma: Terminate DMA when stream on fails
+    - media: xilinx: dma: Enable use of Framebuffer Write IP in V4L2 Driver
+    - v4l: xilinx: dma: Remove colorspace check in xvip_dma_verify_format
+    - media: xilinx: Improve pipeline management code
+    - media: v4l: Group Xilinx downstream formats
+    - documentation: dt: add bindings documentation for xilinx video demosaic
+      driver
+    - v4l: xilinx-demosaic: driver support for xilinx video demosaic
+    - documentation: dt: add bindings documentation for vpss scaler
+    - v4l: xilinx-vpss-scaler: driver support for xilinx vpss scaler
+    - media: v4l: Add HDR support through compound controls
+    - media: v4l2-core: Update V4L2 framework with new fourcc codes
+    - v4l2-core: Update entries for XV15 and XV20 contiguous formats
+    - media: v4l2-ioctl: Add 12 and 16 bpc RGB pixel formats
+    - media: v4l2-ioctl: Add YUV 12bit and 16bit pixel formats
+    - media: v4l2-ioctl: Use correct fourcc for YUV444 10bit format
+    - media: v4l2-ioctl: Add YUV444 12bit and 16bit pixel formats
+    - media: v4l2-ioctl: Add description for new pixel formats
+    - media: videodev2.h: add Hybrid Log Gamma transfer function define
+    - media: videodev2.h: Add control type for HDR
+    - dt: bindings: media: xilinx: Documentation for Xilinx UHDSDI Rx driver
+    - v4l: xilinx: Driver support for Xilinx UHDSDI Rx subsystem
+    - documentation: dt: add bindings documentation for gamma lut ip
+    - v4l: xilinx-gamma: initial driver support for xilinx video gamma lut ip
+    - Documentation: DT: Add bindings documentation for VPSS CSC
+    - v4l: xilinx-vpss-csc: driver support for xilinx vpss csc
+    - drivers: media: Customized adv7511 for Xylon LogiCVC (deprecated)
+    - drm: mipi: Bring DT format description closer to the hardware
+    - drm: xlnx: Xilinx DRM KMS driver
+    - dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings
+    - dt-bindings: display: xlnx: Add bridge bindings
+    - drm: xlnx: drv: Add Xilinx bridge support
+    - dt-bindings: display: xlnx: Adding dsi bindings
+    - drm: xlnx: dsi: Adding dsi driver to new framework
+    - drm: xlnx: adding cursor width / height support
+    - dt-bindings: display: xlnx: Adding mixer bindings
+    - drm: xlnx: mixer: Initial video mixer driver
+    - drm: Add generic HDR support
+    - dt-bindings: display: xlnx: Adding sdi bindings
+    - drm: xlnx: sdi: Adding sdi-tx driver
+    - dt-bindings: dma: xilinx_frmbuf: Add support for 12 and 16 bpc RGB formats
+    - dma: xilinx: Support early callback modes
+    - dt-bindings: display: xlnx: Adding pl_disp bindings
+    - drm: xlnx: DRM KMS driver for xilinx display pipeline
+    - dt: bindings: display: xlnx: Adding csc bindings
+    - drm: xlnx: csc: Adding vpss-color space converter driver
+    - dt: bindings: display: xlnx: Adding scaler bindings
+    - drm: xlnx: scaler: Adding vpss-scaler driver
+    - dt-bindings: display: xlnx: Added vpss bridge phandle as optional property
+    - dt: bindings: display: xlnx: Adding gpio reset entry
+    - drm: xlnx: scaler: Adding vpss-scaler reset through gpio
+    - drm: xlnx: scaler: Adding Zero out H-phase array before changing resolution
+    - drm: xlnx: correcting data type for cursor with and height
+    - media: Add new dt-bindings/vf_codes for supported formats
+    - v4l: xilinx: dma: Update video format descriptor
+    - v4l: xilinx: dma: Add multi-planar support
+    - v4l: xilinx: dma: Fix v4l2 enumeration callback for multiplanar
+    - v4l: xilinx: dma: Add scaling and padding factor functions
+    - v4l: xilinx: dma: Get scaling and padding factor to calculate DMA params
+    - drm: xlnx: scaler: Add YUV420 support
+    - drm: xlnx: csc: Add YUV420 support
+    - Documentation: media: Correct dt-bindings doc for Gamma LUT IP
+    - dt-bindings: display: xlnx: Modifing mixer compatible string
+    - v4l: xilinx-tpg: Add YUV 420 media bus format support to TPG driver
+    - v4l: xilinx: dma: Fix sizeimage calculation
+    - v4l: xilinx: dma: Handle 10 bit format calucations for XV20
+    - v4l: xilinx: dma: Fix bytes per line calculation
+    - v4l: xilinx: Add BGR color format support.
+    - media: xilinx: vip: Correct the fourcc code for BGRX8 format.
+    - dt: bindings: media: xilinx: Remove unimplemented TPG compatible string
+    - v4l: xilinx: dma: Add XV15 and XV20 contiguous format support
+    - uvcvideo: Prevent new URBs being processed at stream stop
+    - dt: bindings: display: xlnx: Updated gpio reset entry
+    - drm: xlnx: scaler: Updating vpss-scaler reset logic
+    - dt: bindings: display: xlnx: Adding gpio reset entry
+    - drm: xlnx: csc: Adding vpss-csc reset through gpio
+    - xilinx: v4l2: dma: Bug fix in single plane support
+    - bindings: display: xlnx: Fixing device tree documentation
+    - dt-bindings: display: xlnx: mixer: Add supported formats table
+    - dt-bindings: display: xlnx: mixer: Update example to fix format strings
+    - v4l: xilinx: dma: Add interlaced support
+    - v4l: xilinx: dma: Terminate DMA when media pipeline fails to start
+    - xilinx: v4l2: dma: Add multiple output support
+    - dt-bindings: display: xlnx: mixer: Added xlnx,num-layers description
+    - dt-bindings: display: xlnx: mixer: Adding xlnx,layer-primary property
+    - dt-bindings: display: xlnx: Add VTC bindings
+    - drm: xlnx: Add a Video Timing Controller(VTC) driver
+    - dt-bindings: display: xlnx: mixer: Adding xlnx vtc bridge support
+    - dt-bindings: display: xlnx: Add VTC bridge support to PL display
+    - xilinx: v4l: dma: Multi-threading issue
+    - xilinx: v4l: dma: Fix bug in calculating interlaced height
+    - dt: bindings: media: xilinx: Doc for Xilinx AXI4-Stream Switch driver
+    - v4l: xilinx: Driver support for Xilinx AXI4-Stream Switch
+    - media: platform: xilinx: Fix Kconfig indentation
+    - xilinx: v4l: dma: Add ioctl operations for v4l2 output device
+    - xilinx: v4l: dma: Add DMA input direction support
+    - xilinx: v4l: dma: Add format enumeration for output
+    - v4l: xilinx: scd: Add v4l2 custom events
+    - documentation: dt: add bindings documentation for Scene Change Detection
+    - v4l: xilinx: scd: New Scene Change Detection driver
+    - documentation: dt: add bindings documentation for multi-scaler
+    - platform: xilinx: Add mem to mem Multi-Scaler driver (XM2MSC)
+    - dt: bindings: media: xilinx: Documentation for mem2mem driver
+    - xilinx: v4l: mem2mem: Initial version of driver
+    - v4l: dma: Use media graph traversal to stream on/off subdevs
+    - drm: fb: Modify check to ensure correctness of flags
+    - documentation: dt: vtpg: Add support for max width and height
+    - v4l: xilinx: tpg: Add check for max width and height
+    - documentation: dt: demosaic: add support for max width and height
+    - documentation: dt: gamma: Add support for max width and height
+    - drm: xlnx: scaler: Fix array out of bound access
+    - xilinx: v4l: dma: Remove unused function definition
+    - dt-bindings: media: xilinx: demosaic: Make max width, height mandatory
+    - dt-bindings: media: xilinx: vpss-csc: Make max width, height mandatory
+    - xilinx: v4l: dma: In case of error xvip_pipeline_start_stop should return
+      gracefully
+    - xilinx: v4l: vipp: Avoid decrementing refcount of a node twice
+    - xilinx: v4l: dma: Invoke s_power function of subdevice
+    - drm: xlnx: Select VIDEOMODE_HELPERS when DRM_XLNX_PL_DISP is selected
+    - media: ov5640: fix get_light_freq on auto
+    - media: ov5640: Don't access ctrl regs when off
+    - xilinx: v4l: dma: Stop subdevs in reverse order of starting
+    - documentation: dt: Add bindings documentation for Streaming SCD
+    - drm: xlnx: crtc: Fix max width and height overflow
+    - dt-bindings: display: xlnx: mixer: Correct DRM fourcc for BGR8 and RGB8
+    - dt: bindings: media: xilinx: Add clock support to AXI4 Stream switch
+    - dt-bindings: display: xlnx: Add device tree binding for xlnx control drivers
+    - media: xilinx: tpg: Add pixel per clock dt support
+    - dt: bindings: media: xilinx: tpg: Add ppc dt bindings.
+    - media: xilinx: tpg: v4l subdevice controls to set fps
+    - media: xilinx: vtc: Dynamically calculate pixel clock
+    - documentation: dt: multi-scaler: Add properties for pixels per clock
+    - documentation: dt: multi-scaler: Add clock framework support
+    - dt-bindings: display: xlnx: Add clock framework support to DSI Tx
+    - dt-bindings: display: xlnx: Add clock framework support to VPSS CSC bridge
+      driver
+    - drm: xlnx: csc: Add clock framework support
+    - dt-bindings: display: xlnx: Add clock framework support to VPSS Scaler
+      bridge driver
+    - drm: xlnx: scaler: Add support for clock framework
+    - dt-bindings: display: xlnx: Add clock framework support to VTC bridge driver
+    - media: xilinx: tpg: dt pixel per clock validate.
+    - v4l: xilinx: dma: Add control for low latency
+    - v4l: xilinx: dma: Add s_ctrl ioctl for low latency capture
+    - v4l: xilinx: vip: Add 12 and 16 bpc RAW and RGB color formats
+    - dt-bindings: media: xilinx: tpg: Update for v8.0
+    - media: xilinx: tpg: Add support for v8.0
+    - dt-bindings: display: xlnx: vpss-csc: Add max width and height properties
+    - drm: xlnx: csc: Add max width and height dt properties
+    - dt-bindings: display: xlnx: Add max width and height as mandatory properties
+    - drm: xlnx: scaler: Add max width and height properties
+    - v4l: xilinx: tpg: Use 10bit media bus codes
+    - v4l: xilinx: vip: Add YUV 10bit media bus formats
+    - v4l: xilinx: vip: Add scaling and padding factor for XY10
+    - v4l: xilinx: vip: Use correct media bus code for RGB 10bit format
+    - v4l: xilinx: vip: Fix stride calculation
+    - v4l: xilinx: vip: Add YUV444 12bit and 16bit formats
+    - dt-bindings: display: xlnx: mixer: Updated compatible string
+    - v4l: xilinx: vip: Keep NV16 first in vip table
+    - v4l: xilinx: vip: Use the right media code for 422 16bit formats
+    - dt-bindings: display: xlnx: dsi: Add command mode support
+    - dt-bindings: display: xlnx: Add support for vpss ip version 2.2
+    - drm: xlnx: scaler: Add support for ip version 2.2
+    - dma: xilinx: Disable low latency capture in file ops open
+    - staging: dt-bindings: xlnxsync: Add initial bindings for Xilinx Synchronizer
+    - staging: xlnxsync: Add driver for Xilinx Synchronizer
+    - dt-bindings: Add device tree binding for xilinx mpeg2tsmux driver
+    - staging: xlnx_tsmux: Initial version of xlnx mpeg2tsmux driver
+    - drm: xlnx: scaler: Improve quality by adding more coefficients
+    - drm/fb_helper: Enable drm_leak_fbdev_smem by default for zynqmp
+    - dt-bindings: display: xlnx: mixer: Add rev 5.0 to compatible string
+    - v4l: xilinx: dma: Prevent divide by zero error
+    - v4l: xilinx: vipp: move xvip_entity_start_stop() to xilinx-vipp
+    - v4l: xilinx: vipp: use async list for start and stop
+    - v4l: xilinx: vipp: do enabling in the dependency check
+    - v4l: xilinx: vipp: remove a loop for graph start / stop
+    - v4l: xilinx: vipp: Change xvip_entity_start/stop to take graph entity
+    - v4l: xilinx: vipp: Remove set streaming on subdev
+    - drm: xlnx: fix some typos in the Kconfig help texts
+    - v4l: xilinx: sdi: Fix the uapi header license
+    - v4l: xilinx: hls: Fix the uapi header license
+    - v4l: xilinx: events: Fix the uapi header license
+    - v4l: xilinx: tpg: Don't read version if HLS IP
+    - v4l: xilinx: dma: Add control handler to v4l2 device
+    - dt: bindings: media: xilinx: Documentation for Xilinx DP Rx subsystem
+    - v4l: xilinx: Driver support for Xilinx DP Rx subsystem
+    - dt-bindings: display: xlnx: mixer: Updated layer max height and width ranges
+    - v4l: xilinx: vipp: Perform stream start/stop at pipeline level
+    - v4l: xilinx: vipp: remove unused variable
+    - v4l: xilinx: dma: Remove struct xventity_list
+    - dt-bindings: display: xlnx: Add DisplayPort Tx bindings
+    - drm: xlnx: dptx: Add DisplayPort tx driver
+    - v4l: xilinx: vip: Fix V4L2_PIX_FMT_XY10 bpl_factor
+    - v4l: xilinx: vip: Fix CHECKED_RETURN warnings
+    - v4l: xilinx: vip: Fix UNINIT warnings
+    - v4l: xilinx: dma: Fix OVERFLOW_BEFORE_WIDEN warnings
+    - media: xilinx: vtc: Fix warning for OVERFLOW_BEFORE_WIDEN
+    - v4l: xilinx: tpg: Fix warnings for NULL_RETURNS
+    - v4l: xilinx: tpg: Fix warnings for CHECKED_RETURN
+    - drm: xlnx: zynqmp_dp: Fix UNINIT type warning
+    - media: dt-bindings: media: i2c: Add bindings for AP1302
+    - media: i2c: Add ON Semiconductor AP1302 ISP driver
+    - dt: bindings: media: xilinx: Doc for Xilinx AXI4-Stream Broadcaster driver
+    - v4l: xilinx: Driver support for Xilinx AXI4-Stream Broadcaster
+    - drm: xlnx: Update DP subsystem with downstream version
+    - drm: xlnx: add a new member extra_name for xlnx_bridge structure
+    - drm: xlnx: bridge: Fix xlnx_bridge_unregister issue
+    - drm: xlnx: zynqmp: remove layer sub node based on DP DT change
+    - dt-bindings: media: xilinx: Add reserved memory usage information
+    - v4l2: xilinx: vipp: Allow reserving memory and DMA using 64bit addresses
+    - dt-bindings: display: xlnx: mixer: Add example for reserved memory usage
+    - dmaengine: xilinx: dpdma: Add support for cyclic dma mode
+    - drm: fourcc: Mark XV20 and XV15 formats as YUV based
+    - phy: Add HDMI PHY configuration options
+    - dt-bindings: media: xilinx: xcsi2rxss: Add YUV420 8b support
+    - v4l: xilinx: xcsi2rxss: Add support for YUV 420 8bpc
+    - v4l: xilinx: csi2rxss: Remove downstream controls
+    - v4l: xilinx: xcsi2rxss: Fix warnings for NULL_RETURNS
+    - v4l2: xilinx: dma: Align width as per underlying DMA prerequisite
+    - v4l: xilinx: vip: Fix bpl_factor values for Bayer formats
+    - v4l: xilinx: vip: Fix incorrect media bus format code
+    - v4l: xilinx: vip: Add 10-bpp Bayer formats support
+    - phy: xilinx: hdmi: Add linerate, nchannels and reset_gt
+    - dt-bindings: media: xilinx: Add HDMI 2.1 Rx subsystem documentation
+    - v4l: xilinx: hdmirx: Add HDMI 2.1 Rx subsystem driver
+    - drm: xlnx: drv: initialize vblank for all crtcs
+    - dt-bindings: display: xlnx: Add HDMI 2.1 Tx subsystem documentation
+    - drm: xlnx: hdmi: Add HDMI 2.1 Tx subsystem driver
+    - dt-bindings: dmaengine: xilinx_dma: Add MCMDA channel ID index description
+    - drm: xlnx: bridge: check bridge->debugfs_file->status when calling strlen
+    - drm: xlnx: zynqmp: tpg should use swap_coeffs as csc matrix
+    - media: vivid: Fix the check of frame interval index
+    - kbuild: add xilinx-sdirxss.h/xilinx-hls.h/xilinx-v4l2-events.h to no-header-
+      test
+    - dt-bindings: media: xilinx: Add xlnx,atomic_streamon documentation
+    - v4l: xilinx: vip: Allow media pipeline enable with single dma start
+    - dt: bindings: phy: Documentation for Xilinx HDMI PHY controller
+    - phy: xilinx-xhdmiphy: initial driver support for xilinx HDMI PHY 2.1 IP
+    - v4l: xilinx: vip: Add support for 3 planar YUV444 8bpc
+    - v4l: xilinx: dma: Add support for 3 planar YUV444 8bpc format
+    - v4l: xilinx: vip: Fix alignment to match open parenthesis
+    - dt-bindings: dmaengine: zynqmp_dma: Convert zynqmp dma bindings to yaml
+    - dt: bindings: phy: Documentation for Xilinx GT QUAD BASE PHY controller for
+      DP
+    - phy: Add driver for GTQUAD BASE for Displayport
+    - dmaengine: xilinx: dpdma: Fix race condition in vsync IRQ
+    - gpio: xilinx: Trivial patch
+    - mmc: sdhci-of-arasan: Add support for dynamic configuration
+    - spi: spi-cadence: Fix SPI CS gets toggling sporadically
+    - mtd: spi-nor: Add dual parallel and stacked mode support
+    - spi: spi-zynqmp-gqspi: Remove txfifo empty check during chip select/deselect
+    - spi: spi-zynqmp-gqspi: Increase timeout interval during data transfer
+    - spi: spi-zynqmp-gqspi: Update driver to support both IO and dma modes
+    - dt-bindings: spi: spi-zynqmp-gqspi: Add support for Xilinx Versal QSPI
+    - spi: spi-zynq-gqspi: Set appropriate tapdelay values
+    - mtd: spi-nor: Update flash lock/unlock feature
+    - mtd: spi-nor: Add EAR support in spi-nor framework
+    - spi: spi-zynqmp-gqspi: Add dual parallel and stacked mode support in driver
+    - spi: spi-zynq-qspi: Add dual parallal and stacked support
+    - spi: spi-zynq-qspi: Fixed buffer overflow in zynq_qspi_exec_mem_op
+    - mtd: spi-nor: Don't parse 4BAIT via Zynq QSPI
+    - mtd: spi-nor: Fix call trace when qspi driver built as module
+    - spi: spi-cadence: Fix kernel-doc format for resume/suspend
+    - spi: spi-cadence: Align function name s/cnds/cdns/g
+    - spi: spi-zynqmp-gqspi: Fix chipselect timeout issue
+    - spi: spi-zynqmp-gqspi: Fix the zynqmp qspi driver call to get the spi
+      controller devdata
+    - spi: spi-zynqmp-gqspi: Fix suspend/resume
+    - spi: spi-zynqmp-gqspi: Fix erase failure when tx buswidth is 4
+    - mtd: spi-nor: Update flash properties in flash_info table
+    - spi: spi-cadence-quadspi: Add support for Stacked mode
+    - spi: spi-xilinx: Updated axi-qspi controller driver
+    - fpga: region: Update runtime PM handling logic
+    - fpga: fpga-region: Add missing kernel-doc description
+    - v4l: xilinx: dprx: Add MMCM configuration for rx_dec_clk for versal systems
+    - firmware: xilinx: Fix incorrect return val in zynqmp_pm_sec_read_reg()
+    - ARM: zynq: Add/Update/Sync DTs for xilinx platforms
+    - arm64: zynqmp: Add/Update/Sync DTs for xilinx platforms
+    - ARM: xilinx: Add zynq defconfig
+    - arm64: xilinx: Add defconfig fragments
+    - microblaze: defconfig: Enable the Marvell phy driver
+    - microblaze: Defconfig sync
+    - microblaze: Add defconfig and DT for SMP design
+    - phy: xilinx-xhdmiphy: Set connector linerate in HDMI-RX TMDS mode
+    - phy: xilinx-xhdmiphy: Fix connector linerate setting in FRL mode
+    - misc: xilinx_flex: Prevent exiting with mutex
+    - dt-bindings: net: cdns,macb: Convert to json-schema
+    - dt-bindings: net: cdns,macb: Add versal compatible string
+    - dt-bindings: net: cdns,macb: added generic PHY and reset mappings for ZynqMP
+    - net: macb: Added ZynqMP-specific initialization
+    - net: macb: Add zynqmp SGMII dynamic configuration support
+    - iio: adc: versal-sysmon: Add macros for delayed work
+    - arm64: configs: xilinx: Enable default usb ethernet and serial gadget
+    - xilinx: Sync defconfig with current Kconfig layout
+    - net: xilinx: Update Kconfig to select XILINX_AXI_EMAC for XILINX_TSN
+    - staging: xlnxsync: Added IOCTL to reset the current syncIp slot
+    - usb: dwc3: gadget: Ignore Update Transfer cmd params
+    - usb: dwc3: gadget: Skip checking Update Transfer status
+    - usb: dwc3: gadget: Handle pending stream transfer bit
+    - misc: xilinx-ai-engine: add device tree overlay support
+    - misc: xilinx-ai-engine: Add frequency scaling kernel APIs
+    - misc: xilinx-ai-engine: Fix QoS and frequency calculations as defined by PLM
+    - misc: xilinx-ai-engine: Remove get/set frequency IOCTLs
+    - misc: xilinx-ai-engine: Add get partition current freq sysfs entry
+    - dt-bindings: media: xilinx: hdmirxss: Add v1.2 compatible string
+    - v4l: xilinx: hdmirxss: Add v1.2 compatible string
+    - v4l: xilinx: hdmirxss: Fix DDC writes for 0xFF field mask
+    - v4l: xilinx: hdmirxss: Correctly disable timers while initializing
+    - microblaze: Add xmb_manager_register function
+    - dt-bindings: misc: tmr-manager: Add device-tree binding for TMR Manager
+    - drivers: misc: Add Support for TMR Manager
+    - microblaze: Add custom break vector handler for mb manager
+    - microblaze: Add support for error injection
+    - dt-bindings: misc: tmr-inject: Add device-tree binding for TMR Inject
+    - drivers: misc: Add Support for TMR Inject IP
+    - usb: misc: Fix gcc warnings for usb2244 and usb5744 driver
+    - v4l: xilinx: hdmirxss: Fix kernel-doc warnings
+    - dt-bindings: soc: xilinx: ai-engine: add aie gen and mem rows
+    - misc: xilinx-ai-engine: move mem clear to dev ops
+    - misc: xilinx-ai-engine: device struct for tile type
+    - misc: xilinx-ai-engine: get device properties from device tree
+    - misc: xilinx-ai-engine: remove hard coded row attributes
+    - misc: xilinx-ai-engine: issue privilege ops to firmware
+    - misc: xilinx-ai-engine: add support for aieml
+    - misc: xilinx-ai-engine: enable aieml device support
+    - misc: xilinx-ai-engine: disable rsc mgr for aieml
+    - misc: xilinx-ai-engine: disable sysfs nodes for aieml
+    - misc: xilinx-ai-engine: disable interrupts for aieml
+    - firmware: xilinx: Move FIRMWARE_VERSION_MASK to xlnx-zynqmp.h
+    - iio: adc: versal-sysmon: Add support for secure access
+    - iio: adc: versal-sysmon: Add support for events on slave SLRs
+    - drm: xlnx: Update dependency for DRM PL display driver
+    - drm: xlnx: Update dependency for ZynqMP DP driver
+    - xilinx: zynq: enabling UEVENT_HELPER
+    - arm64: zynqmp: Add resets property to sdhci nodes
+    - arm64: zynqmp: Add support for zcu102-rev1.1 board
+    - arm64: zynqmp: Add support for Xilinx Kria SOM board
+    - arm64: xilinx: Fix dtb filename for smk-k26 board
+    - arm64: zynqmp: Add the latest changes for SOM boards
+    - arm64: zynqmp: Add all missing dt files for Xilinx boards
+    - arm64: versal: Add all missing dt files for Xilinx boards
+    - dt-bindings: ptp: xilinx: Add additionalProperties
+    - ASoC: xlnx: Set dai_fmt for hdmi and dp sound cards
+    - firmware: xilinx: enable feature check for ZU+
+    - usb: gadget: tcm: error handling for each command allocation
+    - arm64: zynqmp: Fix bias setting for gem1
+    - v4l: xilinx: hls: remove from the UAPI header kernel specific __user macro
+    - usb: dwc3: xilinx: Update GPIO access api with sleep
+    - serial: pl011: Add missing request/release functions
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Wed, 02 Mar 2022 16:00:34 +0800
+
+linux-xilinx-zynqmp (5.15.0-1000.0) jammy; urgency=medium
+
+  * empty entry
+
+ -- Wen-chien Jesse Sung <jesse.sung@canonical.com>  Sun, 16 Aug 2020 15:59:56 +0800
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/config/annotations
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/config/annotations
@@ -0,0 +1,2233 @@
+# Menu: HEADER
+# FORMAT: 4
+# ARCH: arm64
+# FLAVOUR: arm64-xilinx-zynqmp
+
+include "../../debian.master/config/annotations"
+
+CONFIG_ACCESSIBILITY                            policy<{'arm64': 'n'}>
+CONFIG_ACCESSIBILITY                            note<'LP: #1967702'>
+
+CONFIG_ARCH_ROCKCHIP                            policy<{'arm64': 'n'}>
+CONFIG_ARCH_ROCKCHIP                            note<'LP: #2044554'>
+
+CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT       policy<{'arm64': '-'}>
+CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT       note<'LP:1845820'>
+
+CONFIG_BLK_DEV_RAM                              policy<{'arm64': 'y'}>
+CONFIG_BLK_DEV_RAM                              note<'LP #1593293'>
+
+CONFIG_EXT3_FS                                  policy<{'arm64': 'y'}>
+CONFIG_EXT3_FS                                  note<'ext4 handling via EXT4_USE_FOR_EXT23'>
+
+CONFIG_IPMMU_VMSA                               policy<{'arm64': '-'}>
+CONFIG_IPMMU_VMSA                               note<'LP: #2044554'>
+
+CONFIG_IP_PNP                                   policy<{'arm64': 'y'}>
+CONFIG_IP_PNP                                   note<'LP:1259861'>
+
+CONFIG_MMC_SDHCI                                policy<{'arm64': 'y'}>
+CONFIG_MMC_SDHCI                                note<'installation essential on omap/highbank'>
+
+CONFIG_MMC_SDHCI_PLTFM                          policy<{'arm64': 'y'}>
+CONFIG_MMC_SDHCI_PLTFM                          note<'boot essential on highbank'>
+
+CONFIG_MTD                                      policy<{'arm64': 'y'}>
+CONFIG_MTD                                      note<'boot essential on arm'>
+
+CONFIG_MTD_BLOCK                                policy<{'arm64': 'y'}>
+CONFIG_MTD_BLOCK                                note<'boot essential on arm'>
+
+CONFIG_MTD_OF_PARTS                             policy<{'arm64': 'y'}>
+CONFIG_MTD_OF_PARTS                             note<'boot essential on arm'>
+
+CONFIG_MTD_RAW_NAND                             policy<{'arm64': 'y'}>
+CONFIG_MTD_RAW_NAND                             note<'boot essential on arm'>
+
+CONFIG_NR_CPUS                                  policy<{'arm64': '4'}>
+CONFIG_NR_CPUS                                  note<'LP:1864198'>
+
+CONFIG_PCI_MESON                                policy<{'arm64': 'n'}>
+CONFIG_PCI_MESON                                note<'LP: #2007745'>
+
+CONFIG_REGULATOR_FIXED_VOLTAGE                  policy<{'arm64': 'y'}>
+CONFIG_REGULATOR_FIXED_VOLTAGE                  note<'boot essential on arm'>
+
+CONFIG_SATA_AHCI_PLATFORM                       policy<{'arm64': 'y'}>
+CONFIG_SATA_AHCI_PLATFORM                       note<'boot essential on highbank'>
+
+CONFIG_SERIAL_SH_SCI                            policy<{'arm64': '-'}>
+CONFIG_SERIAL_SH_SCI                            note<'LP: #2022361'>
+
+CONFIG_SERIAL_SH_SCI_CONSOLE                    policy<{'arm64': '-'}>
+CONFIG_SERIAL_SH_SCI_CONSOLE                    note<'LP: #2022361'>
+
+CONFIG_SERIAL_SH_SCI_EARLYCON                   policy<{'arm64': '-'}>
+CONFIG_SERIAL_SH_SCI_EARLYCON                   note<'LP: #2022361'>
+
+CONFIG_SND                                      policy<{'arm64': 'y'}>
+CONFIG_SND                                      note<'not autoloadable on omap'>
+
+CONFIG_SND_HDA_SCODEC_CS35L41                   policy<{'arm64': '-'}>
+CONFIG_SND_HDA_SCODEC_CS35L41                   note<'LP:#1965496'>
+
+CONFIG_SND_HDA_SCODEC_CS35L41_I2C               policy<{'arm64': 'n'}>
+CONFIG_SND_HDA_SCODEC_CS35L41_I2C               note<'LP:#1965496'>
+
+CONFIG_SND_HDA_SCODEC_CS35L41_SPI               policy<{'arm64': 'n'}>
+CONFIG_SND_HDA_SCODEC_CS35L41_SPI               note<'LP:#1965496'>
+
+CONFIG_SND_SOC                                  policy<{'arm64': 'y'}>
+CONFIG_SND_SOC                                  note<'not autoloadable on omap'>
+
+CONFIG_SND_SOC_CS35L41                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_CS35L41                          note<'LP:#1965496'>
+
+CONFIG_SND_SOC_CS35L41_I2C                      policy<{'arm64': 'n'}>
+CONFIG_SND_SOC_CS35L41_I2C                      note<'LP:#1965496'>
+
+CONFIG_SND_SOC_CS35L41_LIB                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_CS35L41_LIB                      note<'LP:#1965496'>
+
+CONFIG_SND_SOC_CS35L41_SPI                      policy<{'arm64': 'n'}>
+CONFIG_SND_SOC_CS35L41_SPI                      note<'LP:#1965496'>
+
+CONFIG_SOUND                                    policy<{'arm64': 'y'}>
+CONFIG_SOUND                                    note<'not autoloadable on omap'>
+
+CONFIG_SPEAKUP                                  policy<{'arm64': '-'}>
+CONFIG_SPEAKUP                                  note<'LP: #1967702'>
+
+CONFIG_UBSAN                                    policy<{'arm64': 'n'}>
+CONFIG_UBSAN                                    note<'LP#1942215'>
+
+CONFIG_USB_OTG                                  policy<{'arm64': 'y'}>
+CONFIG_USB_OTG                                  note<'triggers breakage on x86 LP:1047527, LP:1411295'>
+
+
+# ---- Annotations without notes ----
+
+CONFIG_A11Y_BRAILLE_CONSOLE                     policy<{'arm64': '-'}>
+CONFIG_AC97_BUS                                 policy<{'arm64': 'y'}>
+CONFIG_AHCI_BRCM                                policy<{'arm64': '-'}>
+CONFIG_AHCI_IMX                                 policy<{'arm64': '-'}>
+CONFIG_AHCI_MTK                                 policy<{'arm64': '-'}>
+CONFIG_AHCI_MVEBU                               policy<{'arm64': '-'}>
+CONFIG_AHCI_SUNXI                               policy<{'arm64': '-'}>
+CONFIG_AHCI_TEGRA                               policy<{'arm64': '-'}>
+CONFIG_AMLOGIC_THERMAL                          policy<{'arm64': '-'}>
+CONFIG_APPLE_AIC                                policy<{'arm64': '-'}>
+CONFIG_APPLE_DART                               policy<{'arm64': '-'}>
+CONFIG_APQ_GCC_8084                             policy<{'arm64': '-'}>
+CONFIG_APQ_MMCC_8084                            policy<{'arm64': '-'}>
+CONFIG_ARCH_ACTIONS                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_APPLE                               policy<{'arm64': 'n'}>
+CONFIG_ARCH_BCM2835                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_BCM4908                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_BCM_IPROC                           policy<{'arm64': 'n'}>
+CONFIG_ARCH_BERLIN                              policy<{'arm64': 'n'}>
+CONFIG_ARCH_BITMAIN                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_BRCMSTB                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_HAS_RESET_CONTROLLER                policy<{'arm64': '-'}>
+CONFIG_ARCH_HISI                                policy<{'arm64': 'n'}>
+CONFIG_ARCH_INTEL_SOCFPGA                       policy<{'arm64': 'n'}>
+CONFIG_ARCH_K3                                  policy<{'arm64': 'n'}>
+CONFIG_ARCH_KEEMBAY                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_LAYERSCAPE                          policy<{'arm64': 'n'}>
+CONFIG_ARCH_LG1K                                policy<{'arm64': 'n'}>
+CONFIG_ARCH_MEDIATEK                            policy<{'arm64': 'n'}>
+CONFIG_ARCH_MESON                               policy<{'arm64': 'n'}>
+CONFIG_ARCH_MMAP_RND_BITS_MAX                   policy<{'arm64': '33'}>
+CONFIG_ARCH_MMAP_RND_BITS_MIN                   policy<{'arm64': '18'}>
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN            policy<{'arm64': '11'}>
+CONFIG_ARCH_MVEBU                               policy<{'arm64': 'n'}>
+CONFIG_ARCH_MXC                                 policy<{'arm64': 'n'}>
+CONFIG_ARCH_QCOM                                policy<{'arm64': 'n'}>
+CONFIG_ARCH_R8A774A1                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A774B1                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A774C0                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A774E1                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77950                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77951                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77960                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77961                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77965                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77970                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77980                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77990                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A77995                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R8A779A0                            policy<{'arm64': '-'}>
+CONFIG_ARCH_R9A07G044                           policy<{'arm64': '-'}>
+CONFIG_ARCH_RCAR_GEN3                           policy<{'arm64': '-'}>
+CONFIG_ARCH_REALTEK                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_RENESAS                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_S32                                 policy<{'arm64': 'n'}>
+CONFIG_ARCH_SEATTLE                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_SPARX5                              policy<{'arm64': 'n'}>
+CONFIG_ARCH_SPRD                                policy<{'arm64': 'n'}>
+CONFIG_ARCH_SUNXI                               policy<{'arm64': 'n'}>
+CONFIG_ARCH_SYNQUACER                           policy<{'arm64': 'n'}>
+CONFIG_ARCH_TEGRA                               policy<{'arm64': 'n'}>
+CONFIG_ARCH_TEGRA_132_SOC                       policy<{'arm64': '-'}>
+CONFIG_ARCH_TEGRA_186_SOC                       policy<{'arm64': '-'}>
+CONFIG_ARCH_TEGRA_194_SOC                       policy<{'arm64': '-'}>
+CONFIG_ARCH_TEGRA_210_SOC                       policy<{'arm64': '-'}>
+CONFIG_ARCH_TEGRA_234_SOC                       policy<{'arm64': '-'}>
+CONFIG_ARCH_THUNDER                             policy<{'arm64': 'n'}>
+CONFIG_ARCH_THUNDER2                            policy<{'arm64': 'n'}>
+CONFIG_ARCH_VEXPRESS                            policy<{'arm64': 'n'}>
+CONFIG_ARCH_VISCONTI                            policy<{'arm64': 'n'}>
+CONFIG_ARCH_WANT_HUGE_PMD_SHARE                 policy<{'arm64': 'y'}>
+CONFIG_ARCH_XGENE                               policy<{'arm64': 'n'}>
+CONFIG_ARC_EMAC_CORE                            policy<{'arm64': '-'}>
+CONFIG_ARM64_4K_PAGES                           policy<{'arm64': 'y'}>
+CONFIG_ARM64_64K_PAGES                          policy<{'arm64': 'n'}>
+CONFIG_ARM64_CONT_PMD_SHIFT                     policy<{'arm64': '4'}>
+CONFIG_ARM64_CONT_PTE_SHIFT                     policy<{'arm64': '4'}>
+CONFIG_ARM64_PAGE_SHIFT                         policy<{'arm64': '12'}>
+CONFIG_ARM64_VA_BITS_39                         policy<{'arm64': 'n'}>
+CONFIG_ARMADA_37XX_CLK                          policy<{'arm64': '-'}>
+CONFIG_ARMADA_37XX_RWTM_MBOX                    policy<{'arm64': '-'}>
+CONFIG_ARMADA_37XX_WATCHDOG                     policy<{'arm64': '-'}>
+CONFIG_ARMADA_AP806_SYSCON                      policy<{'arm64': '-'}>
+CONFIG_ARMADA_AP_CPU_CLK                        policy<{'arm64': '-'}>
+CONFIG_ARMADA_AP_CP_HELPER                      policy<{'arm64': '-'}>
+CONFIG_ARMADA_CP110_SYSCON                      policy<{'arm64': '-'}>
+CONFIG_ARMADA_THERMAL                           policy<{'arm64': '-'}>
+CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM       policy<{'arm64': '-'}>
+CONFIG_ARM_ARMADA_37XX_CPUFREQ                  policy<{'arm64': '-'}>
+CONFIG_ARM_ARMADA_8K_CPUFREQ                    policy<{'arm64': '-'}>
+CONFIG_ARM_BRCMSTB_AVS_CPUFREQ                  policy<{'arm64': '-'}>
+CONFIG_ARM_GIC_PM                               policy<{'arm64': '-'}>
+CONFIG_ARM_GIC_V3_ITS_FSL_MC                    policy<{'arm64': '-'}>
+CONFIG_ARM_IMX6Q_CPUFREQ                        policy<{'arm64': '-'}>
+CONFIG_ARM_IMX8M_DDRC_DEVFREQ                   policy<{'arm64': '-'}>
+CONFIG_ARM_IMX_BUS_DEVFREQ                      policy<{'arm64': '-'}>
+CONFIG_ARM_IMX_CPUFREQ_DT                       policy<{'arm64': '-'}>
+CONFIG_ARM_MEDIATEK_CPUFREQ                     policy<{'arm64': '-'}>
+CONFIG_ARM_MEDIATEK_CPUFREQ_HW                  policy<{'arm64': '-'}>
+CONFIG_ARM_QCOM_CPUFREQ_HW                      policy<{'arm64': '-'}>
+CONFIG_ARM_QCOM_CPUFREQ_NVMEM                   policy<{'arm64': '-'}>
+CONFIG_ARM_RASPBERRYPI_CPUFREQ                  policy<{'arm64': '-'}>
+CONFIG_ARM_RK3399_DMC_DEVFREQ                   policy<{'arm64': '-'}>
+CONFIG_ARM_SMMU                                 policy<{'arm64': 'n'}>
+CONFIG_ARM_SMMU_LEGACY_DT_BINDINGS              policy<{'arm64': '-'}>
+CONFIG_ARM_SMMU_QCOM                            policy<{'arm64': '-'}>
+CONFIG_ARM_SMMU_V3                              policy<{'arm64': 'n'}>
+CONFIG_ARM_SMMU_V3_SVA                          policy<{'arm64': '-'}>
+CONFIG_ARM_TEGRA124_CPUFREQ                     policy<{'arm64': '-'}>
+CONFIG_ARM_TEGRA186_CPUFREQ                     policy<{'arm64': '-'}>
+CONFIG_ARM_TEGRA194_CPUFREQ                     policy<{'arm64': '-'}>
+CONFIG_ARM_TEGRA20_CPUFREQ                      policy<{'arm64': '-'}>
+CONFIG_ARM_TEGRA_DEVFREQ                        policy<{'arm64': '-'}>
+CONFIG_ARM_TIMER_SP804                          policy<{'arm64': 'n'}>
+CONFIG_ASYNC_TX_DISABLE_PQ_VAL_DMA              policy<{'arm64': '-'}>
+CONFIG_ASYNC_TX_DISABLE_XOR_VAL_DMA             policy<{'arm64': '-'}>
+CONFIG_ASYNC_TX_DMA                             policy<{'arm64': 'n'}>
+CONFIG_ATH10K_DFS_CERTIFIED                     policy<{'arm64': 'n'}>
+CONFIG_ATH10K_SNOC                              policy<{'arm64': '-'}>
+CONFIG_ATH5K_TEST_CHANNELS                      policy<{'arm64': 'n'}>
+CONFIG_ATH6KL_REGDOMAIN                         policy<{'arm64': 'n'}>
+CONFIG_ATH9K_DFS_CERTIFIED                      policy<{'arm64': 'n'}>
+CONFIG_ATH9K_TX99                               policy<{'arm64': 'n'}>
+CONFIG_ATH_REG_DYNAMIC_USER_REG_HINTS           policy<{'arm64': 'n'}>
+CONFIG_AX88796B_PHY                             policy<{'arm64': 'y'}>
+CONFIG_AXIENET_HAS_MCDMA                        policy<{'arm64': 'n'}>
+CONFIG_AXIENET_HAS_TADMA                        policy<{'arm64': 'y'}>
+CONFIG_BCH                                      policy<{'arm64': 'y'}>
+CONFIG_BCM2711_THERMAL                          policy<{'arm64': '-'}>
+CONFIG_BCM2835_MBOX                             policy<{'arm64': '-'}>
+CONFIG_BCM2835_POWER                            policy<{'arm64': '-'}>
+CONFIG_BCM2835_THERMAL                          policy<{'arm64': '-'}>
+CONFIG_BCM2835_VCHIQ                            policy<{'arm64': '-'}>
+CONFIG_BCM2835_VCHIQ_MMAL                       policy<{'arm64': '-'}>
+CONFIG_BCM2835_WDT                              policy<{'arm64': '-'}>
+CONFIG_BCM4908_ENET                             policy<{'arm64': '-'}>
+CONFIG_BCM7038_L1_IRQ                           policy<{'arm64': '-'}>
+CONFIG_BCM7038_WDT                              policy<{'arm64': '-'}>
+CONFIG_BCM_FLEXRM_MBOX                          policy<{'arm64': '-'}>
+CONFIG_BCM_IPROC_ADC                            policy<{'arm64': '-'}>
+CONFIG_BCM_NS_THERMAL                           policy<{'arm64': '-'}>
+CONFIG_BCM_PDC_MBOX                             policy<{'arm64': '-'}>
+CONFIG_BCM_PMB                                  policy<{'arm64': '-'}>
+CONFIG_BCM_SBA_RAID                             policy<{'arm64': 'n'}>
+CONFIG_BCM_SR_THERMAL                           policy<{'arm64': '-'}>
+CONFIG_BCM_VIDEOCORE                            policy<{'arm64': '-'}>
+CONFIG_BERLIN2_ADC                              policy<{'arm64': '-'}>
+CONFIG_BGMAC                                    policy<{'arm64': '-'}>
+CONFIG_BGMAC_PLATFORM                           policy<{'arm64': '-'}>
+CONFIG_BRCMSTB_DPFE                             policy<{'arm64': '-'}>
+CONFIG_BRCMSTB_L2_IRQ                           policy<{'arm64': '-'}>
+CONFIG_BRCMSTB_PM                               policy<{'arm64': '-'}>
+CONFIG_BRCMSTB_THERMAL                          policy<{'arm64': '-'}>
+CONFIG_BRCM_USB_PINMAP                          policy<{'arm64': '-'}>
+CONFIG_BTRFS_FS                                 policy<{'arm64': 'y'}>
+CONFIG_BT_QCOMSMD                               policy<{'arm64': '-'}>
+CONFIG_CADENCE_WATCHDOG                         policy<{'arm64': 'y'}>
+CONFIG_CAN_RCAR                                 policy<{'arm64': '-'}>
+CONFIG_CAN_RCAR_CANFD                           policy<{'arm64': '-'}>
+CONFIG_CAVIUM_CPT                               policy<{'arm64': '-'}>
+CONFIG_CC_HAS_UBSAN_BOUNDS                      policy<{'arm64': '-'}>
+CONFIG_CEC_CORE                                 policy<{'arm64': 'y'}>
+CONFIG_CEC_MESON_AO                             policy<{'arm64': '-'}>
+CONFIG_CEC_MESON_G12A_AO                        policy<{'arm64': '-'}>
+CONFIG_CEC_PIN                                  policy<{'arm64': '-'}>
+CONFIG_CEC_PIN_ERROR_INJ                        policy<{'arm64': '-'}>
+CONFIG_CEC_TEGRA                                policy<{'arm64': '-'}>
+CONFIG_CFG80211_CERTIFICATION_ONUS              policy<{'arm64': 'y'}>
+CONFIG_CFG80211_EXTRA_REGDB_KEYDIR              policy<{'arm64': '""'}>
+CONFIG_CFG80211_REG_CELLULAR_HINTS              policy<{'arm64': 'y'}>
+CONFIG_CFG80211_REG_RELAX_NO_IR                 policy<{'arm64': 'y'}>
+CONFIG_CGROUP_DEBUG                             policy<{'arm64': 'y'}>
+CONFIG_CHARGER_CPCAP                            policy<{'arm64': '-'}>
+CONFIG_CHARGER_QCOM_SMBB                        policy<{'arm64': '-'}>
+CONFIG_CHARGER_SC2731                           policy<{'arm64': '-'}>
+CONFIG_CLK_ACTIONS                              policy<{'arm64': '-'}>
+CONFIG_CLK_BCM2711_DVP                          policy<{'arm64': '-'}>
+CONFIG_CLK_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_CLK_BCM_NS2                              policy<{'arm64': '-'}>
+CONFIG_CLK_BCM_SR                               policy<{'arm64': '-'}>
+CONFIG_CLK_GFM_LPASS_SM8250                     policy<{'arm64': '-'}>
+CONFIG_CLK_IMX8MM                               policy<{'arm64': '-'}>
+CONFIG_CLK_IMX8MN                               policy<{'arm64': '-'}>
+CONFIG_CLK_IMX8MP                               policy<{'arm64': '-'}>
+CONFIG_CLK_IMX8MQ                               policy<{'arm64': '-'}>
+CONFIG_CLK_IMX8QXP                              policy<{'arm64': '-'}>
+CONFIG_CLK_INTEL_SOCFPGA                        policy<{'arm64': '-'}>
+CONFIG_CLK_INTEL_SOCFPGA64                      policy<{'arm64': '-'}>
+CONFIG_CLK_LS1028A_PLLDIG                       policy<{'arm64': '-'}>
+CONFIG_CLK_OWL_S500                             policy<{'arm64': '-'}>
+CONFIG_CLK_OWL_S700                             policy<{'arm64': '-'}>
+CONFIG_CLK_OWL_S900                             policy<{'arm64': '-'}>
+CONFIG_CLK_PX30                                 policy<{'arm64': '-'}>
+CONFIG_CLK_QORIQ                                policy<{'arm64': '-'}>
+CONFIG_CLK_R8A774A1                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A774B1                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A774C0                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A774E1                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A7795                              policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77960                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77961                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77965                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77970                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77980                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77990                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A77995                             policy<{'arm64': '-'}>
+CONFIG_CLK_R8A779A0                             policy<{'arm64': '-'}>
+CONFIG_CLK_R9A07G044                            policy<{'arm64': '-'}>
+CONFIG_CLK_RASPBERRYPI                          policy<{'arm64': '-'}>
+CONFIG_CLK_RCAR_CPG_LIB                         policy<{'arm64': '-'}>
+CONFIG_CLK_RCAR_GEN3_CPG                        policy<{'arm64': '-'}>
+CONFIG_CLK_RCAR_USB2_CLOCK_SEL                  policy<{'arm64': '-'}>
+CONFIG_CLK_RENESAS                              policy<{'arm64': '-'}>
+CONFIG_CLK_RENESAS_CPG_MSSR                     policy<{'arm64': '-'}>
+CONFIG_CLK_RENESAS_DIV6                         policy<{'arm64': '-'}>
+CONFIG_CLK_RK3308                               policy<{'arm64': '-'}>
+CONFIG_CLK_RK3328                               policy<{'arm64': '-'}>
+CONFIG_CLK_RK3368                               policy<{'arm64': '-'}>
+CONFIG_CLK_RK3399                               policy<{'arm64': '-'}>
+CONFIG_CLK_RK3568                               policy<{'arm64': '-'}>
+CONFIG_CLK_RZG2L                                policy<{'arm64': '-'}>
+CONFIG_CLK_SUNXI                                policy<{'arm64': '-'}>
+CONFIG_CLK_SUNXI_CLOCKS                         policy<{'arm64': '-'}>
+CONFIG_CLK_SUNXI_PRCM_SUN6I                     policy<{'arm64': '-'}>
+CONFIG_CLK_SUNXI_PRCM_SUN8I                     policy<{'arm64': '-'}>
+CONFIG_CLK_SUNXI_PRCM_SUN9I                     policy<{'arm64': '-'}>
+CONFIG_CLK_TEGRA_BPMP                           policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_AXG                           policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_AXG_AUDIO                     policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_BM1880                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_FSL_FLEXSPI                   policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_FSL_SAI                       policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_G12A                          policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_GXBB                          policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI3516CV300                   policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI3519                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI3559A                       policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI3660                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI3670                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI3798CV200                   policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI6220                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_HI655X                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_IDT8T49N24X                   policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_IPROC                         policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MEDIATEK                      policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_AO_CLKC                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_CPU_DYNDIV              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_DUALDIV                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_EE_CLKC                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_MPLL                    policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_PHASE                   policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_PLL                     policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_REGMAP                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_SCLK_DIV                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MESON_VID_PLL_DIV             policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_BDPSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_JPGDECSYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_MFGCFG                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_VDECSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT2712_VENCSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_AUDIOSYS               policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_CAMSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_GCESYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MFGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MIPI0ASYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MIPI0BSYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MIPI1ASYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MIPI1BSYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MIPI2ASYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MIPI2BSYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6765_VCODECSYS              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_AUDSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_CAMSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_IPESYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_MFGCFG                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_VDECSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6779_VENCSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6797                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6797_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6797_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6797_VDECSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT6797_VENCSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT7622                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT7622_AUDSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT7622_ETHSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT7622_HIFSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8167                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8167_AUDSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8167_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8167_MFGCFG                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8167_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8167_VDECSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8173                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8173_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_AUDIOSYS               policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_CAMSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_IPU_ADL                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_IPU_CONN               policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_IPU_CORE0              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_IPU_CORE1              policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_MFGCFG                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_VDECSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8183_VENCSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_AUDSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_CAMSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_IMGSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_IMP_IIC_WRAP           policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_IPESYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_MDPSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_MFGCFG                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_MMSYS                  policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_MSDC                   policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_SCP_ADSP               policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_VDECSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8192_VENCSYS                policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8516                        policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_MT8516_AUDSYS                 policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_QCOM                          policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_ROCKCHIP                      policy<{'arm64': '-'}>
+CONFIG_COMMON_CLK_SI5324                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_SI5341                        policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_SI570                         policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_VC7                           policy<{'arm64': 'n'}>
+CONFIG_COMMON_CLK_XLNX_CLKWZRD                  policy<{'arm64': 'y'}>
+CONFIG_COMMON_CLK_XLNX_CLKWZRD_V                policy<{'arm64': 'n'}>
+CONFIG_COMMON_RESET_HI3660                      policy<{'arm64': '-'}>
+CONFIG_COMMON_RESET_HI6220                      policy<{'arm64': '-'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND            policy<{'arm64': 'n'}>
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE           policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_BLAKE2B                           policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_ALLWINNER                     policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_BCM_SPU                       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_CPT                           policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_AHASH_API            policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_AHASH_API_DESC       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_COMMON               policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API           policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API_DESC      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API_QI        policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_DEBUG                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_INTC                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_INTC_COUNT_THLD      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_INTC_TIME_THLD       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_JR                   policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_PKC_API              policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_RINGSIZE             policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_CAAM_RNG_API              policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_FSL_DPAA2_CAAM                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4           policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4_CTS       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_AES_SM4_ECB       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_HCU               policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_KEEMBAY_OCS_HCU_HMAC_SHA224   policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_MARVELL                       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_MARVELL_CESA                  policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_MXS_DCP                       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_OCTEONTX2_CPT                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_OCTEONTX_CPT                  policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE                           policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_AEAD                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_AEAD               policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_ALL                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_SHA                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_ENABLE_SKCIPHER           policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_SHA                       policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_SKCIPHER                  policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCE_SW_MAX_LEN                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_QCOM_RNG                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_ROCKCHIP                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SA2UL                         policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SAHARA                        policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN4I_SS                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN4I_SS_DEBUG                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_DEBUG                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_HASH                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_PRNG                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_CE_TRNG                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS                      policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS_DEBUG                policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS_HASH                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_SUN8I_SS_PRNG                 policy<{'arm64': '-'}>
+CONFIG_CRYPTO_DEV_XILINX_RSA                    policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_ZYNQMP_AES                    policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_DEV_ZYNQMP_KECCAK_384             policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_ECC                               policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_ECDH                              policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_ENGINE                            policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_GHASH_ARM64_CE                    policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_LIB_SM4                           policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA1_ARM64_CE                     policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA256_ARM64                      policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA2_ARM64_CE                     policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA3                              policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA3_ARM64                        policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA512_ARM64                      policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SHA512_ARM64_CE                   policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SM3                               policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SM3_ARM64_CE                      policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_SM4_ARM64_CE                      policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_USER_API                          policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_USER_API_HASH                     policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_USER_API_SKCIPHER                 policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_XXHASH                            policy<{'arm64': 'y'}>
+CONFIG_CRYPTO_ZSTD                              policy<{'arm64': 'y'}>
+CONFIG_DAVICOM_PHY                              policy<{'arm64': 'y'}>
+CONFIG_DEVFREQ_EVENT_ROCKCHIP_DFI               policy<{'arm64': '-'}>
+CONFIG_DMATEST                                  policy<{'arm64': 'y'}>
+CONFIG_DMA_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_DMA_SUN6I                                policy<{'arm64': '-'}>
+CONFIG_DP83848_PHY                              policy<{'arm64': 'y'}>
+CONFIG_DP83867_PHY                              policy<{'arm64': 'y'}>
+CONFIG_DPAA2_CONSOLE                            policy<{'arm64': '-'}>
+CONFIG_DPAA_ERRATUM_A050385                     policy<{'arm64': '-'}>
+CONFIG_DRM                                      policy<{'arm64': 'y'}>
+CONFIG_DRM_CDNS_MHDP8546_J721E                  policy<{'arm64': '-'}>
+CONFIG_DRM_DEBUG_MM                             policy<{'arm64': 'n'}>
+CONFIG_DRM_DP_AUX_BUS                           policy<{'arm64': 'y'}>
+CONFIG_DRM_DW_MIPI_DSI                          policy<{'arm64': '-'}>
+CONFIG_DRM_IMX_DCSS                             policy<{'arm64': '-'}>
+CONFIG_DRM_KMB_DISPLAY                          policy<{'arm64': '-'}>
+CONFIG_DRM_KMS_HELPER                           policy<{'arm64': 'y'}>
+CONFIG_DRM_LIMA                                 policy<{'arm64': 'n'}>
+CONFIG_DRM_MALI_DISPLAY                         policy<{'arm64': 'n'}>
+CONFIG_DRM_MEDIATEK                             policy<{'arm64': '-'}>
+CONFIG_DRM_MEDIATEK_HDMI                        policy<{'arm64': '-'}>
+CONFIG_DRM_MESON                                policy<{'arm64': '-'}>
+CONFIG_DRM_MESON_DW_HDMI                        policy<{'arm64': '-'}>
+CONFIG_DRM_MSM                                  policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DP                               policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI                              policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI_10NM_PHY                     policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI_14NM_PHY                     policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI_20NM_PHY                     policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI_28NM_8960_PHY                policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI_28NM_PHY                     policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_DSI_7NM_PHY                      policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_GPU_STATE                        policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_GPU_SUDO                         policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_HDMI_HDCP                        policy<{'arm64': '-'}>
+CONFIG_DRM_MSM_REGISTER_LOGGING                 policy<{'arm64': '-'}>
+CONFIG_DRM_MXS                                  policy<{'arm64': '-'}>
+CONFIG_DRM_MXSFB                                policy<{'arm64': '-'}>
+CONFIG_DRM_PANEL_SIMPLE                         policy<{'arm64': 'y'}>
+CONFIG_DRM_RCAR_CMM                             policy<{'arm64': '-'}>
+CONFIG_DRM_RCAR_DU                              policy<{'arm64': '-'}>
+CONFIG_DRM_RCAR_LVDS                            policy<{'arm64': '-'}>
+CONFIG_DRM_RCAR_USE_CMM                         policy<{'arm64': '-'}>
+CONFIG_DRM_RCAR_VSP                             policy<{'arm64': '-'}>
+CONFIG_DRM_RCAR_WRITEBACK                       policy<{'arm64': '-'}>
+CONFIG_DRM_ROCKCHIP                             policy<{'arm64': '-'}>
+CONFIG_DRM_SUN4I                                policy<{'arm64': '-'}>
+CONFIG_DRM_SUN4I_BACKEND                        policy<{'arm64': '-'}>
+CONFIG_DRM_SUN4I_HDMI                           policy<{'arm64': '-'}>
+CONFIG_DRM_SUN4I_HDMI_CEC                       policy<{'arm64': '-'}>
+CONFIG_DRM_SUN6I_DSI                            policy<{'arm64': '-'}>
+CONFIG_DRM_SUN8I_DW_HDMI                        policy<{'arm64': '-'}>
+CONFIG_DRM_SUN8I_MIXER                          policy<{'arm64': '-'}>
+CONFIG_DRM_SUN8I_TCON_TOP                       policy<{'arm64': '-'}>
+CONFIG_DRM_TEGRA                                policy<{'arm64': '-'}>
+CONFIG_DRM_TEGRA_DEBUG                          policy<{'arm64': '-'}>
+CONFIG_DRM_TEGRA_STAGING                        policy<{'arm64': '-'}>
+CONFIG_DRM_VC4                                  policy<{'arm64': '-'}>
+CONFIG_DRM_VC4_HDMI_CEC                         policy<{'arm64': '-'}>
+CONFIG_DRM_XLNX                                 policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_BRIDGE                          policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_BRIDGE_CSC                      policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_BRIDGE_DEBUG_FS                 policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_BRIDGE_SCALER                   policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_BRIDGE_VTC                      policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_DPTX                            policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_DSI                             policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_HDMITX                          policy<{'arm64': 'n'}>
+CONFIG_DRM_XLNX_MIXER                           policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_PL_DISP                         policy<{'arm64': 'y'}>
+CONFIG_DRM_XLNX_SDI                             policy<{'arm64': 'y'}>
+CONFIG_DRM_ZOCL                                 policy<{'arm64': 'm'}>
+CONFIG_DVB_CORE                                 policy<{'arm64': 'y'}>
+CONFIG_DVB_MAX_ADAPTERS                         policy<{'arm64': '16'}>
+CONFIG_DWMAC_IMX8                               policy<{'arm64': '-'}>
+CONFIG_DWMAC_IPQ806X                            policy<{'arm64': '-'}>
+CONFIG_DWMAC_MEDIATEK                           policy<{'arm64': '-'}>
+CONFIG_DWMAC_MESON                              policy<{'arm64': '-'}>
+CONFIG_DWMAC_QCOM_ETHQOS                        policy<{'arm64': '-'}>
+CONFIG_DWMAC_ROCKCHIP                           policy<{'arm64': '-'}>
+CONFIG_DWMAC_SOCFPGA                            policy<{'arm64': '-'}>
+CONFIG_DWMAC_SUN8I                              policy<{'arm64': '-'}>
+CONFIG_DWMAC_SUNXI                              policy<{'arm64': '-'}>
+CONFIG_DWMAC_VISCONTI                           policy<{'arm64': '-'}>
+CONFIG_DW_APB_ICTL                              policy<{'arm64': '-'}>
+CONFIG_DW_APB_TIMER                             policy<{'arm64': '-'}>
+CONFIG_DW_APB_TIMER_OF                          policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA                              policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_ETHERNET                     policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_NAND                         policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_OCRAM                        policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_QSPI                         policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_SDMMC                        policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_SDRAM                        policy<{'arm64': '-'}>
+CONFIG_EDAC_ALTERA_USB                          policy<{'arm64': '-'}>
+CONFIG_EDAC_LAYERSCAPE                          policy<{'arm64': '-'}>
+CONFIG_EDAC_LEGACY_SYSFS                        policy<{'arm64': 'y'}>
+CONFIG_EDAC_QCOM                                policy<{'arm64': '-'}>
+CONFIG_EDAC_SYNOPSYS                            policy<{'arm64': 'y'}>
+CONFIG_EDAC_XILINX_DDR                          policy<{'arm64': 'y'}>
+CONFIG_EDAC_ZYNQMP_OCM                          policy<{'arm64': 'y'}>
+CONFIG_EEPROM_AT24                              policy<{'arm64': 'y'}>
+CONFIG_EFI_ARMSTUB_DTB_LOADER                   policy<{'arm64': 'y'}>
+CONFIG_EINT_MTK                                 policy<{'arm64': '-'}>
+CONFIG_EMAC_ROCKCHIP                            policy<{'arm64': '-'}>
+CONFIG_EMBEDDED                                 policy<{'arm64': 'y'}>
+CONFIG_EXT3_FS_POSIX_ACL                        policy<{'arm64': 'n'}>
+CONFIG_EXT3_FS_SECURITY                         policy<{'arm64': 'n'}>
+CONFIG_EXTCON_QCOM_SPMI_MISC                    policy<{'arm64': '-'}>
+CONFIG_FB_IMX                                   policy<{'arm64': '-'}>
+CONFIG_FB_MX3                                   policy<{'arm64': '-'}>
+CONFIG_FB_SH_MOBILE_LCDC                        policy<{'arm64': '-'}>
+CONFIG_FB_SYS_COPYAREA                          policy<{'arm64': 'y'}>
+CONFIG_FB_SYS_FILLRECT                          policy<{'arm64': 'y'}>
+CONFIG_FB_SYS_FOPS                              policy<{'arm64': 'y'}>
+CONFIG_FB_SYS_IMAGEBLIT                         policy<{'arm64': 'y'}>
+CONFIG_FEC                                      policy<{'arm64': '-'}>
+CONFIG_FORCE_MAX_ZONEORDER                      policy<{'arm64': '11'}>
+CONFIG_FPGA                                     policy<{'arm64': 'y'}>
+CONFIG_FPGA_BRIDGE                              policy<{'arm64': 'y'}>
+CONFIG_FPGA_MGR_DEBUG_FS                        policy<{'arm64': 'y'}>
+CONFIG_FPGA_MGR_SOCFPGA                         policy<{'arm64': '-'}>
+CONFIG_FPGA_MGR_SOCFPGA_A10                     policy<{'arm64': '-'}>
+CONFIG_FPGA_MGR_STRATIX10_SOC                   policy<{'arm64': '-'}>
+CONFIG_FPGA_MGR_VERSAL_FPGA                     policy<{'arm64': 'n'}>
+CONFIG_FPGA_MGR_ZYNQMP_FPGA                     policy<{'arm64': 'y'}>
+CONFIG_FPGA_REGION                              policy<{'arm64': 'y'}>
+CONFIG_FRAME_WARN                               policy<{'arm64': '2048'}>
+CONFIG_FSL_BMAN_TEST                            policy<{'arm64': '-'}>
+CONFIG_FSL_BMAN_TEST_API                        policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA                                 policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA2_ETH                            policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA2_ETH_DCB                        policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA2_PTP_CLOCK                      policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA2_QDMA                           policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA_CHECKING                        policy<{'arm64': '-'}>
+CONFIG_FSL_DPAA_ETH                             policy<{'arm64': '-'}>
+CONFIG_FSL_FMAN                                 policy<{'arm64': '-'}>
+CONFIG_FSL_GUTS                                 policy<{'arm64': '-'}>
+CONFIG_FSL_IFC                                  policy<{'arm64': '-'}>
+CONFIG_FSL_IMX8_DDR_PMU                         policy<{'arm64': '-'}>
+CONFIG_FSL_MC_BUS                               policy<{'arm64': '-'}>
+CONFIG_FSL_MC_DPIO                              policy<{'arm64': '-'}>
+CONFIG_FSL_MC_UAPI_SUPPORT                      policy<{'arm64': '-'}>
+CONFIG_FSL_QMAN_TEST                            policy<{'arm64': '-'}>
+CONFIG_FUEL_GAUGE_SC27XX                        policy<{'arm64': '-'}>
+CONFIG_GARP                                     policy<{'arm64': 'y'}>
+CONFIG_GPIO_ALTERA_A10SR                        policy<{'arm64': '-'}>
+CONFIG_GPIO_BCM_XGS_IPROC                       policy<{'arm64': '-'}>
+CONFIG_GPIO_BRCMSTB                             policy<{'arm64': '-'}>
+CONFIG_GPIO_DAVINCI                             policy<{'arm64': '-'}>
+CONFIG_GPIO_EIC_SPRD                            policy<{'arm64': '-'}>
+CONFIG_GPIO_MPC8XXX                             policy<{'arm64': '-'}>
+CONFIG_GPIO_MVEBU                               policy<{'arm64': '-'}>
+CONFIG_GPIO_MXC                                 policy<{'arm64': '-'}>
+CONFIG_GPIO_PCA953X                             policy<{'arm64': 'y'}>
+CONFIG_GPIO_PMIC_EIC_SPRD                       policy<{'arm64': '-'}>
+CONFIG_GPIO_RASPBERRYPI_EXP                     policy<{'arm64': '-'}>
+CONFIG_GPIO_RCAR                                policy<{'arm64': '-'}>
+CONFIG_GPIO_REGMAP                              policy<{'arm64': '-'}>
+CONFIG_GPIO_ROCKCHIP                            policy<{'arm64': '-'}>
+CONFIG_GPIO_SL28CPLD                            policy<{'arm64': '-'}>
+CONFIG_GPIO_SLG7XL45106                         policy<{'arm64': 'y'}>
+CONFIG_GPIO_SPRD                                policy<{'arm64': '-'}>
+CONFIG_GPIO_TEGRA                               policy<{'arm64': '-'}>
+CONFIG_GPIO_TEGRA186                            policy<{'arm64': '-'}>
+CONFIG_GPIO_THUNDERX                            policy<{'arm64': '-'}>
+CONFIG_GPIO_TPS65086                            policy<{'arm64': 'y'}>
+CONFIG_GPIO_VISCONTI                            policy<{'arm64': '-'}>
+CONFIG_GPIO_XGENE_SB                            policy<{'arm64': '-'}>
+CONFIG_GPIO_XLP                                 policy<{'arm64': '-'}>
+CONFIG_GPIO_ZYNQ                                policy<{'arm64': 'y'}>
+CONFIG_GPIO_ZYNQMP_MODEPIN                      policy<{'arm64': 'y'}>
+CONFIG_GRACE_PERIOD                             policy<{'arm64': 'y'}>
+CONFIG_HI3660_MBOX                              policy<{'arm64': '-'}>
+CONFIG_HI6220_MBOX                              policy<{'arm64': '-'}>
+CONFIG_HID                                      policy<{'arm64': 'y'}>
+CONFIG_HID_GENERIC                              policy<{'arm64': 'y'}>
+CONFIG_HISILICON_IRQ_MBIGEN                     policy<{'arm64': '-'}>
+CONFIG_HISILICON_LPC                            policy<{'arm64': '-'}>
+CONFIG_HISI_DMA                                 policy<{'arm64': '-'}>
+CONFIG_HISI_PMU                                 policy<{'arm64': 'y'}>
+CONFIG_HISI_THERMAL                             policy<{'arm64': '-'}>
+CONFIG_HWSPINLOCK_OMAP                          policy<{'arm64': '-'}>
+CONFIG_HWSPINLOCK_QCOM                          policy<{'arm64': '-'}>
+CONFIG_HWSPINLOCK_SPRD                          policy<{'arm64': '-'}>
+CONFIG_HWSPINLOCK_SUN6I                         policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_BCM2835                        policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_CAVIUM                         policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_HISI                           policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_IPROC_RNG200                   policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_MESON                          policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_MTK                            policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_OMAP                           policy<{'arm64': '-'}>
+CONFIG_HW_RANDOM_XGENE                          policy<{'arm64': '-'}>
+CONFIG_I2C_ALGOBIT                              policy<{'arm64': 'y'}>
+CONFIG_I2C_ALTERA                               policy<{'arm64': '-'}>
+CONFIG_I2C_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_I2C_BCM_IPROC                            policy<{'arm64': '-'}>
+CONFIG_I2C_BRCMSTB                              policy<{'arm64': '-'}>
+CONFIG_I2C_CADENCE                              policy<{'arm64': 'm'}>
+CONFIG_I2C_HIX5HD2                              policy<{'arm64': '-'}>
+CONFIG_I2C_IMX                                  policy<{'arm64': '-'}>
+CONFIG_I2C_IMX_LPI2C                            policy<{'arm64': '-'}>
+CONFIG_I2C_MESON                                policy<{'arm64': '-'}>
+CONFIG_I2C_MT65XX                               policy<{'arm64': '-'}>
+CONFIG_I2C_MUX                                  policy<{'arm64': 'y'}>
+CONFIG_I2C_MUX_PCA9541                          policy<{'arm64': 'y'}>
+CONFIG_I2C_MV64XXX                              policy<{'arm64': '-'}>
+CONFIG_I2C_OMAP                                 policy<{'arm64': '-'}>
+CONFIG_I2C_OWL                                  policy<{'arm64': '-'}>
+CONFIG_I2C_PXA                                  policy<{'arm64': '-'}>
+CONFIG_I2C_PXA_SLAVE                            policy<{'arm64': '-'}>
+CONFIG_I2C_QCOM_CCI                             policy<{'arm64': '-'}>
+CONFIG_I2C_QCOM_GENI                            policy<{'arm64': '-'}>
+CONFIG_I2C_QUP                                  policy<{'arm64': '-'}>
+CONFIG_I2C_RCAR                                 policy<{'arm64': '-'}>
+CONFIG_I2C_RIIC                                 policy<{'arm64': '-'}>
+CONFIG_I2C_SH_MOBILE                            policy<{'arm64': '-'}>
+CONFIG_I2C_SLAVE_EEPROM                         policy<{'arm64': 'y'}>
+CONFIG_I2C_SPRD                                 policy<{'arm64': '-'}>
+CONFIG_I2C_SYNQUACER                            policy<{'arm64': '-'}>
+CONFIG_I2C_TEGRA                                policy<{'arm64': '-'}>
+CONFIG_I2C_TEGRA_BPMP                           policy<{'arm64': '-'}>
+CONFIG_I2C_VERSATILE                            policy<{'arm64': '-'}>
+CONFIG_I2C_XGENE_SLIMPRO                        policy<{'arm64': '-'}>
+CONFIG_I2C_XILINX                               policy<{'arm64': 'y'}>
+CONFIG_I2C_XLP9XX                               policy<{'arm64': '-'}>
+CONFIG_ICPLUS_PHY                               policy<{'arm64': 'y'}>
+CONFIG_IIO                                      policy<{'arm64': 'y'}>
+CONFIG_IIO_KFIFO_BUF                            policy<{'arm64': 'y'}>
+CONFIG_IIO_TRIGGERED_BUFFER                     policy<{'arm64': 'y'}>
+CONFIG_IKCONFIG                                 policy<{'arm64': 'y'}>
+CONFIG_IKCONFIG_PROC                            policy<{'arm64': 'y'}>
+CONFIG_IMA_DEFAULT_HASH_SM3                     policy<{'arm64': 'n'}>
+CONFIG_IMX2_WDT                                 policy<{'arm64': '-'}>
+CONFIG_IMX7D_ADC                                policy<{'arm64': '-'}>
+CONFIG_IMX7ULP_WDT                              policy<{'arm64': '-'}>
+CONFIG_IMX8MM_THERMAL                           policy<{'arm64': '-'}>
+CONFIG_IMX_DMA                                  policy<{'arm64': '-'}>
+CONFIG_IMX_DSP                                  policy<{'arm64': '-'}>
+CONFIG_IMX_GPCV2                                policy<{'arm64': '-'}>
+CONFIG_IMX_GPCV2_PM_DOMAINS                     policy<{'arm64': '-'}>
+CONFIG_IMX_INTMUX                               policy<{'arm64': '-'}>
+CONFIG_IMX_IRQSTEER                             policy<{'arm64': '-'}>
+CONFIG_IMX_MBOX                                 policy<{'arm64': '-'}>
+CONFIG_IMX_REMOTEPROC                           policy<{'arm64': '-'}>
+CONFIG_IMX_SCU                                  policy<{'arm64': '-'}>
+CONFIG_IMX_SCU_PD                               policy<{'arm64': '-'}>
+CONFIG_IMX_SC_THERMAL                           policy<{'arm64': '-'}>
+CONFIG_IMX_SC_WDT                               policy<{'arm64': '-'}>
+CONFIG_IMX_SDMA                                 policy<{'arm64': '-'}>
+CONFIG_IMX_THERMAL                              policy<{'arm64': '-'}>
+CONFIG_IMX_WEIM                                 policy<{'arm64': '-'}>
+CONFIG_INA260_ADC                               policy<{'arm64': 'm'}>
+CONFIG_INFINIBAND_VMWARE_PVRDMA                 policy<{'arm64': 'm'}>
+CONFIG_INPUT_HISI_POWERKEY                      policy<{'arm64': '-'}>
+CONFIG_INPUT_PM8941_PWRKEY                      policy<{'arm64': '-'}>
+CONFIG_INPUT_PM8XXX_VIBRATOR                    policy<{'arm64': '-'}>
+CONFIG_INPUT_SC27XX_VIBRA                       policy<{'arm64': '-'}>
+CONFIG_INTEL_STRATIX10_RSU                      policy<{'arm64': '-'}>
+CONFIG_INTEL_STRATIX10_SERVICE                  policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_IMX                         policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_IMX8MM                      policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_IMX8MN                      policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_IMX8MQ                      policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM                        policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_BCM_VOTER              policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_MSM8916                policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_MSM8939                policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_MSM8974                policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_OSM_L3                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_QCS404                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_RPMH                   policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_RPMH_POSSIBLE          policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SC7180                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SC7280                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SC8180X                policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SDM660                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SDM845                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SDX55                  policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SM8150                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SM8250                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SM8350                 policy<{'arm64': '-'}>
+CONFIG_INTERCONNECT_QCOM_SMD_RPM                policy<{'arm64': '-'}>
+CONFIG_IOASID                                   policy<{'arm64': '-'}>
+CONFIG_IOMMU_SVA_LIB                            policy<{'arm64': '-'}>
+CONFIG_IPQ_APSS_6018                            policy<{'arm64': '-'}>
+CONFIG_IPQ_APSS_PLL                             policy<{'arm64': '-'}>
+CONFIG_IPQ_GCC_4019                             policy<{'arm64': '-'}>
+CONFIG_IPQ_GCC_6018                             policy<{'arm64': '-'}>
+CONFIG_IPQ_GCC_806X                             policy<{'arm64': '-'}>
+CONFIG_IPQ_GCC_8074                             policy<{'arm64': '-'}>
+CONFIG_IPQ_LCC_806X                             policy<{'arm64': '-'}>
+CONFIG_IP_PNP_BOOTP                             policy<{'arm64': 'y'}>
+CONFIG_IP_PNP_DHCP                              policy<{'arm64': 'y'}>
+CONFIG_IP_PNP_RARP                              policy<{'arm64': 'y'}>
+CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL policy<{'arm64': 'y'}>
+CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS           policy<{'arm64': '-'}>
+CONFIG_IRQ_SIM                                  policy<{'arm64': 'y'}>
+CONFIG_IR_MESON                                 policy<{'arm64': '-'}>
+CONFIG_IR_MESON_TX                              policy<{'arm64': '-'}>
+CONFIG_IR_MTK                                   policy<{'arm64': '-'}>
+CONFIG_IR_SUNXI                                 policy<{'arm64': '-'}>
+CONFIG_ISO9660_FS                               policy<{'arm64': 'y'}>
+CONFIG_JFFS2_CMODE_FAVOURLZO                    policy<{'arm64': 'n'}>
+CONFIG_JFFS2_CMODE_PRIORITY                     policy<{'arm64': 'y'}>
+CONFIG_JFFS2_FS                                 policy<{'arm64': 'y'}>
+CONFIG_JFFS2_RUBIN                              policy<{'arm64': 'y'}>
+CONFIG_JFFS2_SUMMARY                            policy<{'arm64': 'y'}>
+CONFIG_K3_DMA                                   policy<{'arm64': '-'}>
+CONFIG_K3_RTI_WATCHDOG                          policy<{'arm64': '-'}>
+CONFIG_K3_THERMAL                               policy<{'arm64': '-'}>
+CONFIG_KEEMBAY_WATCHDOG                         policy<{'arm64': '-'}>
+CONFIG_KEYBOARD_GPIO                            policy<{'arm64': 'y'}>
+CONFIG_KEYBOARD_GPIO_POLLED                     policy<{'arm64': 'y'}>
+CONFIG_KEYBOARD_IMX                             policy<{'arm64': '-'}>
+CONFIG_KEYBOARD_IMX_SC_KEY                      policy<{'arm64': '-'}>
+CONFIG_KEYBOARD_NVEC                            policy<{'arm64': '-'}>
+CONFIG_KEYBOARD_SNVS_PWRKEY                     policy<{'arm64': '-'}>
+CONFIG_KEYBOARD_SUN4I_LRADC                     policy<{'arm64': '-'}>
+CONFIG_KEYBOARD_TEGRA                           policy<{'arm64': '-'}>
+CONFIG_KHADAS_MCU_FAN_THERMAL                   policy<{'arm64': '-'}>
+CONFIG_KPSS_XCC                                 policy<{'arm64': '-'}>
+CONFIG_LEDS_GPIO                                policy<{'arm64': 'y'}>
+CONFIG_LEDS_SC27XX_BLTC                         policy<{'arm64': '-'}>
+CONFIG_LEDS_TRIGGER_BACKLIGHT                   policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_CAMERA                      policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_DEFAULT_ON                  policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_GPIO                        policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_HEARTBEAT                   policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_ONESHOT                     policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_TIMER                       policy<{'arm64': 'y'}>
+CONFIG_LEDS_TRIGGER_TRANSIENT                   policy<{'arm64': 'y'}>
+CONFIG_LEGACY_PTY_COUNT                         policy<{'arm64': '256'}>
+CONFIG_LIBCRC32C                                policy<{'arm64': 'y'}>
+CONFIG_LLC                                      policy<{'arm64': 'y'}>
+CONFIG_LOCKD                                    policy<{'arm64': 'y'}>
+CONFIG_LSI_ET1011C_PHY                          policy<{'arm64': 'y'}>
+CONFIG_LS_EXTIRQ                                policy<{'arm64': '-'}>
+CONFIG_LS_SCFG_MSI                              policy<{'arm64': '-'}>
+CONFIG_LXT_PHY                                  policy<{'arm64': 'y'}>
+CONFIG_MAC80211_DEBUG_COUNTERS                  policy<{'arm64': 'n'}>
+CONFIG_MAC80211_DEBUG_MENU                      policy<{'arm64': 'y'}>
+CONFIG_MAC80211_HT_DEBUG                        policy<{'arm64': 'n'}>
+CONFIG_MAC80211_IBSS_DEBUG                      policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MESH_CSA_DEBUG                  policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MESH_PS_DEBUG                   policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MESH_SYNC_DEBUG                 policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MHWMP_DEBUG                     policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MLME_DEBUG                      policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MPATH_DEBUG                     policy<{'arm64': 'n'}>
+CONFIG_MAC80211_MPL_DEBUG                       policy<{'arm64': 'n'}>
+CONFIG_MAC80211_NOINLINE                        policy<{'arm64': 'n'}>
+CONFIG_MAC80211_OCB_DEBUG                       policy<{'arm64': 'n'}>
+CONFIG_MAC80211_PS_DEBUG                        policy<{'arm64': 'n'}>
+CONFIG_MAC80211_STA_DEBUG                       policy<{'arm64': 'n'}>
+CONFIG_MAC80211_TDLS_DEBUG                      policy<{'arm64': 'n'}>
+CONFIG_MAC80211_VERBOSE_DEBUG                   policy<{'arm64': 'n'}>
+CONFIG_MACB                                     policy<{'arm64': 'y'}>
+CONFIG_MACVLAN                                  policy<{'arm64': 'y'}>
+CONFIG_MALI400                                  policy<{'arm64': 'm'}>
+CONFIG_MALI400_DEBUG                            policy<{'arm64': 'n'}>
+CONFIG_MALI400_PROFILING                        policy<{'arm64': 'n'}>
+CONFIG_MALI400_UMP                              policy<{'arm64': 'n'}>
+CONFIG_MALI450                                  policy<{'arm64': 'n'}>
+CONFIG_MALI470                                  policy<{'arm64': 'n'}>
+CONFIG_MALI_DEVFREQ                             policy<{'arm64': 'n'}>
+CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH               policy<{'arm64': 'n'}>
+CONFIG_MALI_DT                                  policy<{'arm64': 'y'}>
+CONFIG_MALI_DVFS                                policy<{'arm64': 'n'}>
+CONFIG_MALI_PMU_PARALLEL_POWER_UP               policy<{'arm64': 'n'}>
+CONFIG_MALI_QUIET                               policy<{'arm64': 'y'}>
+CONFIG_MALI_SHARED_INTERRUPTS                   policy<{'arm64': 'y'}>
+CONFIG_MARVELL_PHY                              policy<{'arm64': 'y'}>
+CONFIG_MDIO_BCM_IPROC                           policy<{'arm64': '-'}>
+CONFIG_MDIO_BUS_MUX                             policy<{'arm64': 'm'}>
+CONFIG_MDIO_BUS_MUX_BCM_IPROC                   policy<{'arm64': '-'}>
+CONFIG_MDIO_BUS_MUX_MESON_G12A                  policy<{'arm64': '-'}>
+CONFIG_MDIO_SUN4I                               policy<{'arm64': '-'}>
+CONFIG_MDIO_XGENE                               policy<{'arm64': '-'}>
+CONFIG_MDM_GCC_9607                             policy<{'arm64': '-'}>
+CONFIG_MDM_GCC_9615                             policy<{'arm64': '-'}>
+CONFIG_MDM_LCC_9615                             policy<{'arm64': '-'}>
+CONFIG_MEDIATEK_MT6577_AUXADC                   policy<{'arm64': '-'}>
+CONFIG_MEDIATEK_WATCHDOG                        policy<{'arm64': '-'}>
+CONFIG_MEDIA_CEC_RC                             policy<{'arm64': '-'}>
+CONFIG_MEDIA_SUPPORT                            policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER                              policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_MC44S803                     policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_MT20XX                       policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_SIMPLE                       policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_TDA18271                     policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_TDA827X                      policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_TDA8290                      policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_TDA9887                      policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_TEA5761                      policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_TEA5767                      policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_XC2028                       policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_XC4000                       policy<{'arm64': 'y'}>
+CONFIG_MEDIA_TUNER_XC5000                       policy<{'arm64': 'y'}>
+CONFIG_MESON_CANVAS                             policy<{'arm64': '-'}>
+CONFIG_MESON_CLK_MEASURE                        policy<{'arm64': '-'}>
+CONFIG_MESON_EE_PM_DOMAINS                      policy<{'arm64': '-'}>
+CONFIG_MESON_EFUSE                              policy<{'arm64': '-'}>
+CONFIG_MESON_GXBB_WATCHDOG                      policy<{'arm64': '-'}>
+CONFIG_MESON_GXL_PHY                            policy<{'arm64': '-'}>
+CONFIG_MESON_GX_PM_DOMAINS                      policy<{'arm64': '-'}>
+CONFIG_MESON_GX_SOCINFO                         policy<{'arm64': '-'}>
+CONFIG_MESON_IRQ_GPIO                           policy<{'arm64': '-'}>
+CONFIG_MESON_MX_EFUSE                           policy<{'arm64': '-'}>
+CONFIG_MESON_SARADC                             policy<{'arm64': '-'}>
+CONFIG_MESON_SECURE_PM_DOMAINS                  policy<{'arm64': '-'}>
+CONFIG_MESON_SM                                 policy<{'arm64': '-'}>
+CONFIG_MESON_WATCHDOG                           policy<{'arm64': '-'}>
+CONFIG_MFD_AC100                                policy<{'arm64': '-'}>
+CONFIG_MFD_ALTERA_A10SR                         policy<{'arm64': '-'}>
+CONFIG_MFD_ALTERA_SYSMGR                        policy<{'arm64': '-'}>
+CONFIG_MFD_AXP20X_RSB                           policy<{'arm64': '-'}>
+CONFIG_MFD_DA9150                               policy<{'arm64': 'y'}>
+CONFIG_MFD_HI655X_PMIC                          policy<{'arm64': '-'}>
+CONFIG_MFD_KHADAS_MCU                           policy<{'arm64': '-'}>
+CONFIG_MFD_NVEC                                 policy<{'arm64': '-'}>
+CONFIG_MFD_QCOM_RPM                             policy<{'arm64': '-'}>
+CONFIG_MFD_SC27XX_PMIC                          policy<{'arm64': '-'}>
+CONFIG_MFD_SIMPLE_MFD_I2C                       policy<{'arm64': '-'}>
+CONFIG_MFD_SL28CPLD                             policy<{'arm64': '-'}>
+CONFIG_MFD_SPMI_PMIC                            policy<{'arm64': '-'}>
+CONFIG_MFD_SUN4I_GPADC                          policy<{'arm64': '-'}>
+CONFIG_MFD_SUN6I_PRCM                           policy<{'arm64': '-'}>
+CONFIG_MFD_TI_AM335X_TSCADC                     policy<{'arm64': '-'}>
+CONFIG_MFD_TPS65086                             policy<{'arm64': 'y'}>
+CONFIG_MICREL_PHY                               policy<{'arm64': 'y'}>
+CONFIG_MMC_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_MMC_CAVIUM_THUNDERX                      policy<{'arm64': '-'}>
+CONFIG_MMC_CQHCI                                policy<{'arm64': 'y'}>
+CONFIG_MMC_DW_ROCKCHIP                          policy<{'arm64': '-'}>
+CONFIG_MMC_MESON_GX                             policy<{'arm64': '-'}>
+CONFIG_MMC_MESON_MX_SDIO                        policy<{'arm64': '-'}>
+CONFIG_MMC_MXC                                  policy<{'arm64': '-'}>
+CONFIG_MMC_OWL                                  policy<{'arm64': '-'}>
+CONFIG_MMC_QCOM_DML                             policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_AM654                          policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_BRCMSTB                        policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_ESDHC_IMX                      policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_IPROC                          policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_MSM                            policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_OF_ARASAN                      policy<{'arm64': 'y'}>
+CONFIG_MMC_SDHCI_OF_ESDHC                       policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_OF_SPARX5                      policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_PXAV3                          policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_SPRD                           policy<{'arm64': '-'}>
+CONFIG_MMC_SDHCI_TEGRA                          policy<{'arm64': '-'}>
+CONFIG_MMC_SDHI                                 policy<{'arm64': '-'}>
+CONFIG_MMC_SDHI_INTERNAL_DMAC                   policy<{'arm64': '-'}>
+CONFIG_MMC_SDHI_SYS_DMAC                        policy<{'arm64': '-'}>
+CONFIG_MMC_SH_MMCIF                             policy<{'arm64': '-'}>
+CONFIG_MMC_SUNXI                                policy<{'arm64': '-'}>
+CONFIG_MMC_TMIO_CORE                            policy<{'arm64': '-'}>
+CONFIG_MODULE_FORCE_UNLOAD                      policy<{'arm64': 'y'}>
+CONFIG_MQ_IOSCHED_KYBER                         policy<{'arm64': 'y'}>
+CONFIG_MRP                                      policy<{'arm64': 'y'}>
+CONFIG_MSM_GCC_8660                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8916                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8939                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8953                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8960                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8974                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8994                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8996                             policy<{'arm64': '-'}>
+CONFIG_MSM_GCC_8998                             policy<{'arm64': '-'}>
+CONFIG_MSM_GPUCC_8998                           policy<{'arm64': '-'}>
+CONFIG_MSM_LCC_8960                             policy<{'arm64': '-'}>
+CONFIG_MSM_MMCC_8960                            policy<{'arm64': '-'}>
+CONFIG_MSM_MMCC_8974                            policy<{'arm64': '-'}>
+CONFIG_MSM_MMCC_8994                            policy<{'arm64': '-'}>
+CONFIG_MSM_MMCC_8996                            policy<{'arm64': '-'}>
+CONFIG_MSM_MMCC_8998                            policy<{'arm64': '-'}>
+CONFIG_MST_IRQ                                  policy<{'arm64': '-'}>
+CONFIG_MT7622_WMAC                              policy<{'arm64': '-'}>
+CONFIG_MTD_BLKDEVS                              policy<{'arm64': 'y'}>
+CONFIG_MTD_BLOCK_RO                             policy<{'arm64': '-'}>
+CONFIG_MTD_CFI                                  policy<{'arm64': 'y'}>
+CONFIG_MTD_CFI_INTELEXT                         policy<{'arm64': 'y'}>
+CONFIG_MTD_CFI_UTIL                             policy<{'arm64': 'y'}>
+CONFIG_MTD_CMDLINE_PARTS                        policy<{'arm64': 'y'}>
+CONFIG_MTD_DATAFLASH                            policy<{'arm64': 'y'}>
+CONFIG_MTD_GEN_PROBE                            policy<{'arm64': 'y'}>
+CONFIG_MTD_NAND_ARASAN                          policy<{'arm64': 'y'}>
+CONFIG_MTD_NAND_CORE                            policy<{'arm64': 'y'}>
+CONFIG_MTD_NAND_FSL_IFC                         policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_GPMI_NAND                       policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_HISI504                         policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_MARVELL                         policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_MESON                           policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_MTK                             policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_MXC                             policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_QCOM                            policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_ROCKCHIP                        policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_SUNXI                           policy<{'arm64': '-'}>
+CONFIG_MTD_NAND_TEGRA                           policy<{'arm64': '-'}>
+CONFIG_MTD_OF_PARTS_BCM4908                     policy<{'arm64': '-'}>
+CONFIG_MTD_OF_PARTS_LINKSYS_NS                  policy<{'arm64': '-'}>
+CONFIG_MTD_OOPS                                 policy<{'arm64': 'y'}>
+CONFIG_MTD_PARSER_TRX                           policy<{'arm64': '-'}>
+CONFIG_MTD_QCOMSMEM_PARTS                       policy<{'arm64': '-'}>
+CONFIG_MTD_SPI_NOR                              policy<{'arm64': 'y'}>
+CONFIG_MTD_SPI_NOR_USE_4K_SECTORS               policy<{'arm64': 'n'}>
+CONFIG_MTD_TESTS                                policy<{'arm64': 'm'}>
+CONFIG_MTD_UBI                                  policy<{'arm64': 'y'}>
+CONFIG_MTK_CMDQ                                 policy<{'arm64': '-'}>
+CONFIG_MTK_CMDQ_MBOX                            policy<{'arm64': '-'}>
+CONFIG_MTK_CQDMA                                policy<{'arm64': '-'}>
+CONFIG_MTK_DEVAPC                               policy<{'arm64': '-'}>
+CONFIG_MTK_EFUSE                                policy<{'arm64': '-'}>
+CONFIG_MTK_HSDMA                                policy<{'arm64': '-'}>
+CONFIG_MTK_INFRACFG                             policy<{'arm64': '-'}>
+CONFIG_MTK_IOMMU                                policy<{'arm64': '-'}>
+CONFIG_MTK_MMSYS                                policy<{'arm64': '-'}>
+CONFIG_MTK_PMIC_WRAP                            policy<{'arm64': '-'}>
+CONFIG_MTK_SCP                                  policy<{'arm64': '-'}>
+CONFIG_MTK_SCPSYS                               policy<{'arm64': '-'}>
+CONFIG_MTK_SCPSYS_PM_DOMAINS                    policy<{'arm64': '-'}>
+CONFIG_MTK_SMI                                  policy<{'arm64': '-'}>
+CONFIG_MTK_THERMAL                              policy<{'arm64': '-'}>
+CONFIG_MTK_TIMER                                policy<{'arm64': '-'}>
+CONFIG_MTK_UART_APDMA                           policy<{'arm64': '-'}>
+CONFIG_MVEBU_GICP                               policy<{'arm64': '-'}>
+CONFIG_MVEBU_ICU                                policy<{'arm64': '-'}>
+CONFIG_MVEBU_ODMI                               policy<{'arm64': '-'}>
+CONFIG_MVEBU_PIC                                policy<{'arm64': '-'}>
+CONFIG_MVEBU_SEI                                policy<{'arm64': '-'}>
+CONFIG_MVNETA                                   policy<{'arm64': '-'}>
+CONFIG_MVPP2                                    policy<{'arm64': '-'}>
+CONFIG_MVPP2_PTP                                policy<{'arm64': '-'}>
+CONFIG_MV_XOR                                   policy<{'arm64': '-'}>
+CONFIG_MX3_IPU                                  policy<{'arm64': '-'}>
+CONFIG_MX3_IPU_IRQS                             policy<{'arm64': '-'}>
+CONFIG_MXC_CLK                                  policy<{'arm64': '-'}>
+CONFIG_MXC_CLK_SCU                              policy<{'arm64': '-'}>
+CONFIG_MXS_DMA                                  policy<{'arm64': '-'}>
+CONFIG_NATIONAL_PHY                             policy<{'arm64': 'y'}>
+CONFIG_NET_DEV_REFCNT_TRACKER                   policy<{'arm64': 'n'}>
+CONFIG_NET_KEY_MIGRATE                          policy<{'arm64': 'y'}>
+CONFIG_NET_PKTGEN                               policy<{'arm64': 'y'}>
+CONFIG_NET_SCH_MQPRIO                           policy<{'arm64': 'y'}>
+CONFIG_NET_SCH_SKBPRIO                          policy<{'arm64': 'y'}>
+CONFIG_NET_VENDOR_ACTIONS                       policy<{'arm64': '-'}>
+CONFIG_NET_VENDOR_ALLWINNER                     policy<{'arm64': '-'}>
+CONFIG_NET_VENDOR_MEDIATEK                      policy<{'arm64': '-'}>
+CONFIG_NET_VENDOR_S2I                           policy<{'arm64': 'm'}>
+CONFIG_NET_XGENE                                policy<{'arm64': '-'}>
+CONFIG_NET_XGENE_V2                             policy<{'arm64': '-'}>
+CONFIG_NFS_ACL_SUPPORT                          policy<{'arm64': 'y'}>
+CONFIG_NFS_FS                                   policy<{'arm64': 'y'}>
+CONFIG_NFS_FSCACHE                              policy<{'arm64': '-'}>
+CONFIG_NFS_V2                                   policy<{'arm64': 'y'}>
+CONFIG_NFS_V3                                   policy<{'arm64': 'y'}>
+CONFIG_NFS_V4                                   policy<{'arm64': 'y'}>
+CONFIG_NF_CONNTRACK_PROCFS                      policy<{'arm64': 'y'}>
+CONFIG_NL80211_TESTMODE                         policy<{'arm64': 'y'}>
+CONFIG_NLS_DEFAULT                              policy<{'arm64': '"iso8859-1"'}>
+CONFIG_NLS_ISO8859_1                            policy<{'arm64': 'y'}>
+CONFIG_NOUVEAU_PLATFORM_DRIVER                  policy<{'arm64': '-'}>
+CONFIG_NVEC_PAZ00                               policy<{'arm64': '-'}>
+CONFIG_NVEC_POWER                               policy<{'arm64': '-'}>
+CONFIG_NVMEM_BCM_OCOTP                          policy<{'arm64': '-'}>
+CONFIG_NVMEM_IMX_IIM                            policy<{'arm64': '-'}>
+CONFIG_NVMEM_IMX_OCOTP                          policy<{'arm64': '-'}>
+CONFIG_NVMEM_IMX_OCOTP_SCU                      policy<{'arm64': '-'}>
+CONFIG_NVMEM_SNVS_LPGPR                         policy<{'arm64': '-'}>
+CONFIG_NVMEM_SUNXI_SID                          policy<{'arm64': '-'}>
+CONFIG_OF_CONFIGFS                              policy<{'arm64': 'y'}>
+CONFIG_OF_FPGA_REGION                           policy<{'arm64': 'y'}>
+CONFIG_OMAP2PLUS_MBOX                           policy<{'arm64': '-'}>
+CONFIG_OMAP_MBOX_KFIFO_SIZE                     policy<{'arm64': '-'}>
+CONFIG_OMAP_USB2                                policy<{'arm64': '-'}>
+CONFIG_OVERLAY_FS                               policy<{'arm64': 'y'}>
+CONFIG_OWL_DMA                                  policy<{'arm64': '-'}>
+CONFIG_OWL_EMAC                                 policy<{'arm64': '-'}>
+CONFIG_OWL_PM_DOMAINS                           policy<{'arm64': '-'}>
+CONFIG_OWL_PM_DOMAINS_HELPER                    policy<{'arm64': '-'}>
+CONFIG_OWL_TIMER                                policy<{'arm64': '-'}>
+CONFIG_PATA_IMX                                 policy<{'arm64': '-'}>
+CONFIG_PCIE_ARMADA_8K                           policy<{'arm64': '-'}>
+CONFIG_PCIE_BRCMSTB                             policy<{'arm64': '-'}>
+CONFIG_PCIE_HISI_STB                            policy<{'arm64': '-'}>
+CONFIG_PCIE_IPROC                               policy<{'arm64': '-'}>
+CONFIG_PCIE_IPROC_MSI                           policy<{'arm64': '-'}>
+CONFIG_PCIE_IPROC_PLATFORM                      policy<{'arm64': '-'}>
+CONFIG_PCIE_KEEMBAY                             policy<{'arm64': '-'}>
+CONFIG_PCIE_KEEMBAY_EP                          policy<{'arm64': '-'}>
+CONFIG_PCIE_KEEMBAY_HOST                        policy<{'arm64': '-'}>
+CONFIG_PCIE_LAYERSCAPE_GEN4                     policy<{'arm64': '-'}>
+CONFIG_PCIE_MEDIATEK                            policy<{'arm64': '-'}>
+CONFIG_PCIE_MEDIATEK_GEN3                       policy<{'arm64': '-'}>
+CONFIG_PCIE_QCOM                                policy<{'arm64': '-'}>
+CONFIG_PCIE_RCAR_EP                             policy<{'arm64': '-'}>
+CONFIG_PCIE_RCAR_HOST                           policy<{'arm64': '-'}>
+CONFIG_PCIE_ROCKCHIP                            policy<{'arm64': '-'}>
+CONFIG_PCIE_ROCKCHIP_DW_HOST                    policy<{'arm64': '-'}>
+CONFIG_PCIE_ROCKCHIP_EP                         policy<{'arm64': '-'}>
+CONFIG_PCIE_ROCKCHIP_HOST                       policy<{'arm64': '-'}>
+CONFIG_PCIE_TEGRA194                            policy<{'arm64': '-'}>
+CONFIG_PCIE_TEGRA194_EP                         policy<{'arm64': '-'}>
+CONFIG_PCIE_TEGRA194_HOST                       policy<{'arm64': '-'}>
+CONFIG_PCIE_VISCONTI_HOST                       policy<{'arm64': '-'}>
+CONFIG_PCIE_XDMA_PL                             policy<{'arm64': 'y'}>
+CONFIG_PCI_AARDVARK                             policy<{'arm64': '-'}>
+CONFIG_PCI_BRIDGE_EMUL                          policy<{'arm64': '-'}>
+CONFIG_PCI_IMX6                                 policy<{'arm64': '-'}>
+CONFIG_PCI_KEYSTONE                             policy<{'arm64': '-'}>
+CONFIG_PCI_KEYSTONE_EP                          policy<{'arm64': '-'}>
+CONFIG_PCI_KEYSTONE_HOST                        policy<{'arm64': '-'}>
+CONFIG_PCI_LAYERSCAPE                           policy<{'arm64': '-'}>
+CONFIG_PCI_LAYERSCAPE_EP                        policy<{'arm64': '-'}>
+CONFIG_PCI_TEGRA                                policy<{'arm64': '-'}>
+CONFIG_PGTABLE_LEVELS                           policy<{'arm64': '4'}>
+CONFIG_PHYLINK                                  policy<{'arm64': 'y'}>
+CONFIG_PHY_AM654_SERDES                         policy<{'arm64': '-'}>
+CONFIG_PHY_BCM_NS_USB2                          policy<{'arm64': '-'}>
+CONFIG_PHY_BCM_NS_USB3                          policy<{'arm64': '-'}>
+CONFIG_PHY_BCM_SR_PCIE                          policy<{'arm64': '-'}>
+CONFIG_PHY_BCM_SR_USB                           policy<{'arm64': '-'}>
+CONFIG_PHY_BERLIN_SATA                          policy<{'arm64': '-'}>
+CONFIG_PHY_BERLIN_USB                           policy<{'arm64': '-'}>
+CONFIG_PHY_BRCM_SATA                            policy<{'arm64': '-'}>
+CONFIG_PHY_BRCM_USB                             policy<{'arm64': '-'}>
+CONFIG_PHY_HI3660_USB                           policy<{'arm64': '-'}>
+CONFIG_PHY_HI3670_USB                           policy<{'arm64': '-'}>
+CONFIG_PHY_HI6220_USB                           policy<{'arm64': '-'}>
+CONFIG_PHY_HISI_INNO_USB2                       policy<{'arm64': '-'}>
+CONFIG_PHY_HISTB_COMBPHY                        policy<{'arm64': '-'}>
+CONFIG_PHY_INTEL_KEEMBAY_EMMC                   policy<{'arm64': '-'}>
+CONFIG_PHY_INTEL_KEEMBAY_USB                    policy<{'arm64': '-'}>
+CONFIG_PHY_J721E_WIZ                            policy<{'arm64': '-'}>
+CONFIG_PHY_MESON8B_USB2                         policy<{'arm64': '-'}>
+CONFIG_PHY_MESON_AXG_MIPI_DPHY                  policy<{'arm64': '-'}>
+CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG           policy<{'arm64': '-'}>
+CONFIG_PHY_MESON_AXG_PCIE                       policy<{'arm64': '-'}>
+CONFIG_PHY_MESON_G12A_USB2                      policy<{'arm64': '-'}>
+CONFIG_PHY_MESON_G12A_USB3_PCIE                 policy<{'arm64': '-'}>
+CONFIG_PHY_MESON_GXL_USB2                       policy<{'arm64': '-'}>
+CONFIG_PHY_MTK_HDMI                             policy<{'arm64': '-'}>
+CONFIG_PHY_MTK_MIPI_DSI                         policy<{'arm64': '-'}>
+CONFIG_PHY_MTK_TPHY                             policy<{'arm64': '-'}>
+CONFIG_PHY_MTK_UFS                              policy<{'arm64': '-'}>
+CONFIG_PHY_MTK_XSPHY                            policy<{'arm64': '-'}>
+CONFIG_PHY_MVEBU_A3700_COMPHY                   policy<{'arm64': '-'}>
+CONFIG_PHY_MVEBU_A3700_UTMI                     policy<{'arm64': '-'}>
+CONFIG_PHY_MVEBU_A38X_COMPHY                    policy<{'arm64': '-'}>
+CONFIG_PHY_MVEBU_CP110_COMPHY                   policy<{'arm64': '-'}>
+CONFIG_PHY_MVEBU_CP110_UTMI                     policy<{'arm64': '-'}>
+CONFIG_PHY_NS2_PCIE                             policy<{'arm64': '-'}>
+CONFIG_PHY_NS2_USB_DRD                          policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_APQ8064_SATA                    policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_IPQ4019_USB                     policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_IPQ806X_SATA                    policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_IPQ806X_USB                     policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_PCIE2                           policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_QMP                             policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_QUSB2                           policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_USB_HS_28NM                     policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2               policy<{'arm64': '-'}>
+CONFIG_PHY_QCOM_USB_SS                          policy<{'arm64': '-'}>
+CONFIG_PHY_RCAR_GEN2                            policy<{'arm64': '-'}>
+CONFIG_PHY_RCAR_GEN3_PCIE                       policy<{'arm64': '-'}>
+CONFIG_PHY_RCAR_GEN3_USB2                       policy<{'arm64': '-'}>
+CONFIG_PHY_RCAR_GEN3_USB3                       policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_DP                          policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_DPHY_RX0                    policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_EMMC                        policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY                policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY                policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_INNO_HDMI                   policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_INNO_USB2                   policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_PCIE                        policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_TYPEC                       policy<{'arm64': '-'}>
+CONFIG_PHY_ROCKCHIP_USB                         policy<{'arm64': '-'}>
+CONFIG_PHY_SPARX5_SERDES                        policy<{'arm64': '-'}>
+CONFIG_PHY_SUN4I_USB                            policy<{'arm64': '-'}>
+CONFIG_PHY_SUN50I_USB3                          policy<{'arm64': '-'}>
+CONFIG_PHY_SUN6I_MIPI_DPHY                      policy<{'arm64': '-'}>
+CONFIG_PHY_SUN9I_USB                            policy<{'arm64': '-'}>
+CONFIG_PHY_TEGRA194_P2U                         policy<{'arm64': '-'}>
+CONFIG_PHY_TEGRA_XUSB                           policy<{'arm64': '-'}>
+CONFIG_PHY_TI_GMII_SEL                          policy<{'arm64': '-'}>
+CONFIG_PHY_XILINX_DPGTQUAD                      policy<{'arm64': 'n'}>
+CONFIG_PHY_XILINX_HDMIPHY                       policy<{'arm64': 'n'}>
+CONFIG_PHY_XILINX_ZYNQMP                        policy<{'arm64': 'y'}>
+CONFIG_PINCTRL_APQ8064                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_APQ8084                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_ARMADA_37XX                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_ARMADA_AP806                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_ARMADA_CP110                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_AS370                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_BCM2835                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_BERLIN                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_BERLIN_BG4CT                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_BM1880                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX                              policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8DXL                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8MM                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8MN                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8MP                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8MQ                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8QM                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8QXP                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX8ULP                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IMX_SCU                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IPQ4019                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IPQ6018                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IPQ8064                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IPQ8074                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_IPROC_GPIO                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_KEEMBAY                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_LPASS_LPI                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MDM9607                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MDM9615                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON8_PMX                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON_A1                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON_AXG                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON_AXG_PMX                    policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON_G12A                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON_GXBB                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MESON_GXL                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM                              policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8226                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8660                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8916                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8953                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8960                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8976                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8994                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8996                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8998                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MSM8X74                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT2712                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT6397                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT6765                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT6779                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT6797                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT7622                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8167                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8173                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8183                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8192                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8195                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8365                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MT8516                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MTK                              policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MTK_MOORE                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MTK_PARIS                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MTK_V2                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_MVEBU                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_NS2_MUX                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_OWL                              policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A774A1                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A774B1                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A774C0                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A774E1                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77950                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77951                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77960                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77961                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77965                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77970                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77980                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77990                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A77995                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_PFC_R8A779A0                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_QCOM_SPMI_PMIC                   policy<{'arm64': '-'}>
+CONFIG_PINCTRL_QCOM_SSBI_PMIC                   policy<{'arm64': '-'}>
+CONFIG_PINCTRL_QCS404                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_QDF2XXX                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_RENESAS                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_ROCKCHIP                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_RZG2L                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_S700                             policy<{'arm64': '-'}>
+CONFIG_PINCTRL_S900                             policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SC7180                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SC7280                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SC8180X                          policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SDM660                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SDM845                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SDX55                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SH_PFC                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SM6115                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SM6125                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SM8150                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SM8250                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SM8350                           policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SPRD                             policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SPRD_SC9860                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN4I_A10                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_A100                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_A100_R                    policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_A64                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_A64_R                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_H5                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_H6                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_H616                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_H616_R                    policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN50I_H6_R                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN5I                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN6I_A31                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN6I_A31_R                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_A23                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_A23_R                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_A33                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_A83T                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_A83T_R                     policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_H3                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_H3_R                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN8I_V3S                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN9I_A80                        policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUN9I_A80_R                      policy<{'arm64': '-'}>
+CONFIG_PINCTRL_SUNXI                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_TEGRA                            policy<{'arm64': '-'}>
+CONFIG_PINCTRL_TEGRA124                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_TEGRA194                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_TEGRA210                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_TEGRA_XUSB                       policy<{'arm64': '-'}>
+CONFIG_PINCTRL_TMPV7700                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_VISCONTI                         policy<{'arm64': '-'}>
+CONFIG_PINCTRL_ZYNQMP                           policy<{'arm64': 'y'}>
+CONFIG_PM8916_WATCHDOG                          policy<{'arm64': '-'}>
+CONFIG_PMBUS                                    policy<{'arm64': 'y'}>
+CONFIG_PNFS_BLOCK                               policy<{'arm64': 'y'}>
+CONFIG_PNFS_FILE_LAYOUT                         policy<{'arm64': 'y'}>
+CONFIG_PNFS_FLEXFILE_LAYOUT                     policy<{'arm64': 'y'}>
+CONFIG_POWER_RESET_HISI                         policy<{'arm64': '-'}>
+CONFIG_POWER_RESET_LINKSTATION                  policy<{'arm64': '-'}>
+CONFIG_POWER_RESET_MSM                          policy<{'arm64': '-'}>
+CONFIG_POWER_RESET_OCELOT_RESET                 policy<{'arm64': '-'}>
+CONFIG_POWER_RESET_QCOM_PON                     policy<{'arm64': '-'}>
+CONFIG_POWER_RESET_SC27XX                       policy<{'arm64': '-'}>
+CONFIG_PRINT_QUOTA_WARNING                      policy<{'arm64': 'y'}>
+CONFIG_PRU_REMOTEPROC                           policy<{'arm64': '-'}>
+CONFIG_PTP_1588_CLOCK_DTE                       policy<{'arm64': '-'}>
+CONFIG_PTP_1588_CLOCK_KVM                       policy<{'arm64': 'y'}>
+CONFIG_PTP_1588_CLOCK_XILINX                    policy<{'arm64': 'n'}>
+CONFIG_PWM_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_PWM_BCM_IPROC                            policy<{'arm64': '-'}>
+CONFIG_PWM_BERLIN                               policy<{'arm64': '-'}>
+CONFIG_PWM_BRCMSTB                              policy<{'arm64': '-'}>
+CONFIG_PWM_CADENCE                              policy<{'arm64': 'y'}>
+CONFIG_PWM_HIBVT                                policy<{'arm64': '-'}>
+CONFIG_PWM_IMX1                                 policy<{'arm64': '-'}>
+CONFIG_PWM_IMX27                                policy<{'arm64': '-'}>
+CONFIG_PWM_IMX_TPM                              policy<{'arm64': '-'}>
+CONFIG_PWM_KEEMBAY                              policy<{'arm64': '-'}>
+CONFIG_PWM_MEDIATEK                             policy<{'arm64': '-'}>
+CONFIG_PWM_MESON                                policy<{'arm64': '-'}>
+CONFIG_PWM_MTK_DISP                             policy<{'arm64': '-'}>
+CONFIG_PWM_RASPBERRYPI_POE                      policy<{'arm64': '-'}>
+CONFIG_PWM_RCAR                                 policy<{'arm64': '-'}>
+CONFIG_PWM_RENESAS_TPU                          policy<{'arm64': '-'}>
+CONFIG_PWM_ROCKCHIP                             policy<{'arm64': '-'}>
+CONFIG_PWM_SL28CPLD                             policy<{'arm64': '-'}>
+CONFIG_PWM_SPRD                                 policy<{'arm64': '-'}>
+CONFIG_PWM_SUN4I                                policy<{'arm64': '-'}>
+CONFIG_PWM_TEGRA                                policy<{'arm64': '-'}>
+CONFIG_PWM_TIECAP                               policy<{'arm64': '-'}>
+CONFIG_PWM_TIEHRPWM                             policy<{'arm64': '-'}>
+CONFIG_PWM_VISCONTI                             policy<{'arm64': '-'}>
+CONFIG_PWRSEQ_EMMC                              policy<{'arm64': 'y'}>
+CONFIG_PWRSEQ_SIMPLE                            policy<{'arm64': 'y'}>
+CONFIG_PXA168_ETH                               policy<{'arm64': '-'}>
+CONFIG_QCOM_A53PLL                              policy<{'arm64': '-'}>
+CONFIG_QCOM_A7PLL                               policy<{'arm64': '-'}>
+CONFIG_QCOM_AOSS_QMP                            policy<{'arm64': '-'}>
+CONFIG_QCOM_APCS_IPC                            policy<{'arm64': '-'}>
+CONFIG_QCOM_APR                                 policy<{'arm64': '-'}>
+CONFIG_QCOM_BAM_DMA                             policy<{'arm64': '-'}>
+CONFIG_QCOM_CLK_APCC_MSM8996                    policy<{'arm64': '-'}>
+CONFIG_QCOM_CLK_APCS_MSM8916                    policy<{'arm64': '-'}>
+CONFIG_QCOM_CLK_APCS_SDX55                      policy<{'arm64': '-'}>
+CONFIG_QCOM_CLK_RPM                             policy<{'arm64': '-'}>
+CONFIG_QCOM_CLK_RPMH                            policy<{'arm64': '-'}>
+CONFIG_QCOM_CLK_SMD_RPM                         policy<{'arm64': '-'}>
+CONFIG_QCOM_COINCELL                            policy<{'arm64': '-'}>
+CONFIG_QCOM_COMMAND_DB                          policy<{'arm64': '-'}>
+CONFIG_QCOM_CPR                                 policy<{'arm64': '-'}>
+CONFIG_QCOM_EBI2                                policy<{'arm64': '-'}>
+CONFIG_QCOM_FASTRPC                             policy<{'arm64': '-'}>
+CONFIG_QCOM_GDSC                                policy<{'arm64': '-'}>
+CONFIG_QCOM_GENI_SE                             policy<{'arm64': '-'}>
+CONFIG_QCOM_GPI_DMA                             policy<{'arm64': '-'}>
+CONFIG_QCOM_GSBI                                policy<{'arm64': '-'}>
+CONFIG_QCOM_HFPLL                               policy<{'arm64': '-'}>
+CONFIG_QCOM_IOMMU                               policy<{'arm64': '-'}>
+CONFIG_QCOM_IPA                                 policy<{'arm64': '-'}>
+CONFIG_QCOM_IPCC                                policy<{'arm64': '-'}>
+CONFIG_QCOM_IRQ_COMBINER                        policy<{'arm64': '-'}>
+CONFIG_QCOM_KRYO_L2_ACCESSORS                   policy<{'arm64': '-'}>
+CONFIG_QCOM_L2_PMU                              policy<{'arm64': '-'}>
+CONFIG_QCOM_L3_PMU                              policy<{'arm64': '-'}>
+CONFIG_QCOM_LLCC                                policy<{'arm64': '-'}>
+CONFIG_QCOM_LMH                                 policy<{'arm64': '-'}>
+CONFIG_QCOM_MDT_LOADER                          policy<{'arm64': '-'}>
+CONFIG_QCOM_OCMEM                               policy<{'arm64': '-'}>
+CONFIG_QCOM_PDC                                 policy<{'arm64': '-'}>
+CONFIG_QCOM_PDR_HELPERS                         policy<{'arm64': '-'}>
+CONFIG_QCOM_PIL_INFO                            policy<{'arm64': '-'}>
+CONFIG_QCOM_Q6V5_ADSP                           policy<{'arm64': '-'}>
+CONFIG_QCOM_Q6V5_COMMON                         policy<{'arm64': '-'}>
+CONFIG_QCOM_Q6V5_MSS                            policy<{'arm64': '-'}>
+CONFIG_QCOM_Q6V5_PAS                            policy<{'arm64': '-'}>
+CONFIG_QCOM_Q6V5_WCSS                           policy<{'arm64': '-'}>
+CONFIG_QCOM_QFPROM                              policy<{'arm64': '-'}>
+CONFIG_QCOM_RMTFS_MEM                           policy<{'arm64': '-'}>
+CONFIG_QCOM_RPMCC                               policy<{'arm64': '-'}>
+CONFIG_QCOM_RPMH                                policy<{'arm64': '-'}>
+CONFIG_QCOM_RPMHPD                              policy<{'arm64': '-'}>
+CONFIG_QCOM_RPMPD                               policy<{'arm64': '-'}>
+CONFIG_QCOM_RPROC_COMMON                        policy<{'arm64': '-'}>
+CONFIG_QCOM_SCM                                 policy<{'arm64': '-'}>
+CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT           policy<{'arm64': '-'}>
+CONFIG_QCOM_SMD_RPM                             policy<{'arm64': '-'}>
+CONFIG_QCOM_SMEM                                policy<{'arm64': '-'}>
+CONFIG_QCOM_SMEM_STATE                          policy<{'arm64': '-'}>
+CONFIG_QCOM_SMP2P                               policy<{'arm64': '-'}>
+CONFIG_QCOM_SMSM                                policy<{'arm64': '-'}>
+CONFIG_QCOM_SOCINFO                             policy<{'arm64': '-'}>
+CONFIG_QCOM_SPMI_ADC_TM5                        policy<{'arm64': '-'}>
+CONFIG_QCOM_SPMI_TEMP_ALARM                     policy<{'arm64': '-'}>
+CONFIG_QCOM_SYSMON                              policy<{'arm64': '-'}>
+CONFIG_QCOM_TSENS                               policy<{'arm64': '-'}>
+CONFIG_QCOM_WCNSS_CTRL                          policy<{'arm64': '-'}>
+CONFIG_QCOM_WCNSS_PIL                           policy<{'arm64': '-'}>
+CONFIG_QCOM_WDT                                 policy<{'arm64': '-'}>
+CONFIG_QCS_GCC_404                              policy<{'arm64': '-'}>
+CONFIG_QCS_Q6SSTOP_404                          policy<{'arm64': '-'}>
+CONFIG_QCS_TURING_404                           policy<{'arm64': '-'}>
+CONFIG_QFMT_V2                                  policy<{'arm64': 'y'}>
+CONFIG_QORIQ_CPUFREQ                            policy<{'arm64': '-'}>
+CONFIG_QORIQ_THERMAL                            policy<{'arm64': '-'}>
+CONFIG_QSEMI_PHY                                policy<{'arm64': 'y'}>
+CONFIG_QUOTA_TREE                               policy<{'arm64': 'y'}>
+CONFIG_RAID6_PQ                                 policy<{'arm64': 'y'}>
+CONFIG_RASPBERRYPI_FIRMWARE                     policy<{'arm64': '-'}>
+CONFIG_RASPBERRYPI_POWER                        policy<{'arm64': '-'}>
+CONFIG_RAVB                                     policy<{'arm64': '-'}>
+CONFIG_RCAR_DMAC                                policy<{'arm64': '-'}>
+CONFIG_RCAR_GEN3_THERMAL                        policy<{'arm64': '-'}>
+CONFIG_RCAR_THERMAL                             policy<{'arm64': '-'}>
+CONFIG_RCU_TRACE                                policy<{'arm64': 'y'}>
+CONFIG_REALTEK_PHY                              policy<{'arm64': 'y'}>
+CONFIG_REGMAP_AC97                              policy<{'arm64': '-'}>
+CONFIG_REGULATOR_ANATOP                         policy<{'arm64': '-'}>
+CONFIG_REGULATOR_GPIO                           policy<{'arm64': 'y'}>
+CONFIG_REGULATOR_HI655X                         policy<{'arm64': '-'}>
+CONFIG_REGULATOR_MT6380                         policy<{'arm64': '-'}>
+CONFIG_REGULATOR_QCOM_RPM                       policy<{'arm64': '-'}>
+CONFIG_REGULATOR_QCOM_RPMH                      policy<{'arm64': '-'}>
+CONFIG_REGULATOR_QCOM_SMD_RPM                   policy<{'arm64': '-'}>
+CONFIG_REGULATOR_SC2731                         policy<{'arm64': '-'}>
+CONFIG_REGULATOR_TPS65086                       policy<{'arm64': 'y'}>
+CONFIG_REGULATOR_VQMMC_IPQ4019                  policy<{'arm64': '-'}>
+CONFIG_RENESAS_DMA                              policy<{'arm64': '-'}>
+CONFIG_RENESAS_IRQC                             policy<{'arm64': '-'}>
+CONFIG_RENESAS_RPCIF                            policy<{'arm64': '-'}>
+CONFIG_RENESAS_RZAWDT                           policy<{'arm64': '-'}>
+CONFIG_RENESAS_USB_DMAC                         policy<{'arm64': '-'}>
+CONFIG_RENESAS_WDT                              policy<{'arm64': '-'}>
+CONFIG_RESET_A10SR                              policy<{'arm64': '-'}>
+CONFIG_RESET_BERLIN                             policy<{'arm64': '-'}>
+CONFIG_RESET_BRCMSTB                            policy<{'arm64': '-'}>
+CONFIG_RESET_BRCMSTB_RESCAL                     policy<{'arm64': '-'}>
+CONFIG_RESET_HISI                               policy<{'arm64': '-'}>
+CONFIG_RESET_IMX7                               policy<{'arm64': '-'}>
+CONFIG_RESET_MCHP_SPARX5                        policy<{'arm64': '-'}>
+CONFIG_RESET_MESON                              policy<{'arm64': '-'}>
+CONFIG_RESET_MESON_AUDIO_ARB                    policy<{'arm64': '-'}>
+CONFIG_RESET_QCOM_AOSS                          policy<{'arm64': '-'}>
+CONFIG_RESET_QCOM_PDC                           policy<{'arm64': '-'}>
+CONFIG_RESET_RASPBERRYPI                        policy<{'arm64': '-'}>
+CONFIG_RESET_RZG2L_USBPHY_CTRL                  policy<{'arm64': '-'}>
+CONFIG_RESET_SIMPLE                             policy<{'arm64': '-'}>
+CONFIG_RESET_SUNXI                              policy<{'arm64': '-'}>
+CONFIG_RESET_TEGRA_BPMP                         policy<{'arm64': '-'}>
+CONFIG_RESET_TI_SCI                             policy<{'arm64': '-'}>
+CONFIG_RFKILL_GPIO                              policy<{'arm64': 'y'}>
+CONFIG_ROCKCHIP_ANALOGIX_DP                     policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_CDN_DP                          policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_DW_HDMI                         policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_DW_MIPI_DSI                     policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_EFUSE                           policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_GRF                             policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_INNO_HDMI                       policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_IODOMAIN                        policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_IOMMU                           policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_LVDS                            policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_MBOX                            policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_OTP                             policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_PM_DOMAINS                      policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_RGB                             policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_RK3066_HDMI                     policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_SARADC                          policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_THERMAL                         policy<{'arm64': '-'}>
+CONFIG_ROCKCHIP_TIMER                           policy<{'arm64': '-'}>
+CONFIG_ROOT_NFS                                 policy<{'arm64': 'y'}>
+CONFIG_RPMSG_MTK_SCP                            policy<{'arm64': '-'}>
+CONFIG_RPMSG_QCOM_GLINK_SMEM                    policy<{'arm64': '-'}>
+CONFIG_RPMSG_QCOM_SMD                           policy<{'arm64': '-'}>
+CONFIG_RST_RCAR                                 policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_ARMADA38X                        policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_BRCMSTB                          policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_FSL_FTM_ALARM                    policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_IMXDI                            policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_IMX_SC                           policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_MESON_VRTC                       policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_MT2712                           policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_MT7622                           policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_MV                               policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_MXC                              policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_MXC_V2                           policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_PM8XXX                           policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_RTD119X                          policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_SC27XX                           policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_SH                               policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_SNVS                             policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_SUN6I                            policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_TEGRA                            policy<{'arm64': '-'}>
+CONFIG_RTC_DRV_XGENE                            policy<{'arm64': '-'}>
+CONFIG_RTD119X_WATCHDOG                         policy<{'arm64': '-'}>
+CONFIG_RZG2L_ADC                                policy<{'arm64': '-'}>
+CONFIG_RZ_DMAC                                  policy<{'arm64': '-'}>
+CONFIG_SAMPLE_QMI_CLIENT                        policy<{'arm64': '-'}>
+CONFIG_SATA_AHCI_SEATTLE                        policy<{'arm64': '-'}>
+CONFIG_SATA_RCAR                                policy<{'arm64': '-'}>
+CONFIG_SC27XX_ADC                               policy<{'arm64': '-'}>
+CONFIG_SC27XX_EFUSE                             policy<{'arm64': '-'}>
+CONFIG_SCSI_UFS_HISI                            policy<{'arm64': '-'}>
+CONFIG_SCSI_UFS_MEDIATEK                        policy<{'arm64': '-'}>
+CONFIG_SCSI_UFS_QCOM                            policy<{'arm64': '-'}>
+CONFIG_SCSI_UFS_TI_J721E                        policy<{'arm64': '-'}>
+CONFIG_SC_CAMCC_7180                            policy<{'arm64': '-'}>
+CONFIG_SC_DISPCC_7180                           policy<{'arm64': '-'}>
+CONFIG_SC_DISPCC_7280                           policy<{'arm64': '-'}>
+CONFIG_SC_GCC_7180                              policy<{'arm64': '-'}>
+CONFIG_SC_GCC_7280                              policy<{'arm64': '-'}>
+CONFIG_SC_GCC_8180X                             policy<{'arm64': '-'}>
+CONFIG_SC_GPUCC_7180                            policy<{'arm64': '-'}>
+CONFIG_SC_GPUCC_7280                            policy<{'arm64': '-'}>
+CONFIG_SC_LPASS_CORECC_7180                     policy<{'arm64': '-'}>
+CONFIG_SC_MSS_7180                              policy<{'arm64': '-'}>
+CONFIG_SC_VIDEOCC_7180                          policy<{'arm64': '-'}>
+CONFIG_SC_VIDEOCC_7280                          policy<{'arm64': '-'}>
+CONFIG_SDM_CAMCC_845                            policy<{'arm64': '-'}>
+CONFIG_SDM_DISPCC_845                           policy<{'arm64': '-'}>
+CONFIG_SDM_GCC_660                              policy<{'arm64': '-'}>
+CONFIG_SDM_GCC_845                              policy<{'arm64': '-'}>
+CONFIG_SDM_GPUCC_660                            policy<{'arm64': '-'}>
+CONFIG_SDM_GPUCC_845                            policy<{'arm64': '-'}>
+CONFIG_SDM_LPASSCC_845                          policy<{'arm64': '-'}>
+CONFIG_SDM_MMCC_660                             policy<{'arm64': '-'}>
+CONFIG_SDM_VIDEOCC_845                          policy<{'arm64': '-'}>
+CONFIG_SDX_GCC_55                               policy<{'arm64': '-'}>
+CONFIG_SECRETMEM                                policy<{'arm64': '-'}>
+CONFIG_SENSORS_IIO_HWMON                        policy<{'arm64': 'y'}>
+CONFIG_SENSORS_IR38064                          policy<{'arm64': 'y'}>
+CONFIG_SENSORS_IRPS5401                         policy<{'arm64': 'y'}>
+CONFIG_SENSORS_LM63                             policy<{'arm64': 'y'}>
+CONFIG_SENSORS_MAX20751                         policy<{'arm64': 'y'}>
+CONFIG_SENSORS_PMBUS                            policy<{'arm64': 'y'}>
+CONFIG_SENSORS_PWM_FAN                          policy<{'arm64': 'y'}>
+CONFIG_SENSORS_RASPBERRYPI_HWMON                policy<{'arm64': '-'}>
+CONFIG_SENSORS_SL28CPLD                         policy<{'arm64': '-'}>
+CONFIG_SENSORS_SPARX5                           policy<{'arm64': '-'}>
+CONFIG_SENSORS_TPS544                           policy<{'arm64': 'n'}>
+CONFIG_SERIAL_8250_BCM2835AUX                   policy<{'arm64': '-'}>
+CONFIG_SERIAL_8250_BCM7271                      policy<{'arm64': '-'}>
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS           policy<{'arm64': 'y'}>
+CONFIG_SERIAL_8250_EXAR                         policy<{'arm64': 'y'}>
+CONFIG_SERIAL_8250_MT6577                       policy<{'arm64': '-'}>
+CONFIG_SERIAL_8250_NR_UARTS                     policy<{'arm64': '4'}>
+CONFIG_SERIAL_8250_OMAP                         policy<{'arm64': '-'}>
+CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP              policy<{'arm64': '-'}>
+CONFIG_SERIAL_8250_RUNTIME_UARTS                policy<{'arm64': '4'}>
+CONFIG_SERIAL_8250_TEGRA                        policy<{'arm64': '-'}>
+CONFIG_SERIAL_AMBA_PL010                        policy<{'arm64': 'y'}>
+CONFIG_SERIAL_AMBA_PL010_CONSOLE                policy<{'arm64': 'y'}>
+CONFIG_SERIAL_IMX                               policy<{'arm64': '-'}>
+CONFIG_SERIAL_IMX_CONSOLE                       policy<{'arm64': '-'}>
+CONFIG_SERIAL_IMX_EARLYCON                      policy<{'arm64': '-'}>
+CONFIG_SERIAL_MESON                             policy<{'arm64': '-'}>
+CONFIG_SERIAL_MESON_CONSOLE                     policy<{'arm64': '-'}>
+CONFIG_SERIAL_MSM                               policy<{'arm64': '-'}>
+CONFIG_SERIAL_MSM_CONSOLE                       policy<{'arm64': '-'}>
+CONFIG_SERIAL_MVEBU_CONSOLE                     policy<{'arm64': '-'}>
+CONFIG_SERIAL_MVEBU_UART                        policy<{'arm64': '-'}>
+CONFIG_SERIAL_OWL                               policy<{'arm64': '-'}>
+CONFIG_SERIAL_OWL_CONSOLE                       policy<{'arm64': '-'}>
+CONFIG_SERIAL_QCOM_GENI                         policy<{'arm64': '-'}>
+CONFIG_SERIAL_QCOM_GENI_CONSOLE                 policy<{'arm64': '-'}>
+CONFIG_SERIAL_SAMSUNG                           policy<{'arm64': '-'}>
+CONFIG_SERIAL_SAMSUNG_UARTS                     policy<{'arm64': '-'}>
+CONFIG_SERIAL_SAMSUNG_UARTS_4                   policy<{'arm64': '-'}>
+CONFIG_SERIAL_SH_SCI_DMA                        policy<{'arm64': '-'}>
+CONFIG_SERIAL_SH_SCI_NR_UARTS                   policy<{'arm64': '-'}>
+CONFIG_SERIAL_TEGRA                             policy<{'arm64': '-'}>
+CONFIG_SERIAL_TEGRA_TCU                         policy<{'arm64': '-'}>
+CONFIG_SERIAL_TEGRA_TCU_CONSOLE                 policy<{'arm64': '-'}>
+CONFIG_SERIAL_UARTLITE                          policy<{'arm64': 'y'}>
+CONFIG_SERIAL_UARTLITE_CONSOLE                  policy<{'arm64': 'y'}>
+CONFIG_SERIAL_UARTLITE_NR_UARTS                 policy<{'arm64': '16'}>
+CONFIG_SERIAL_UARTLITE_RS485                    policy<{'arm64': 'y'}>
+CONFIG_SERIAL_XILINX_PS_UART                    policy<{'arm64': 'y'}>
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE            policy<{'arm64': 'y'}>
+CONFIG_SERIO_NVEC_PS2                           policy<{'arm64': '-'}>
+CONFIG_SERIO_SERPORT                            policy<{'arm64': 'y'}>
+CONFIG_SERIO_SUN4I_PS2                          policy<{'arm64': '-'}>
+CONFIG_SH_ETH                                   policy<{'arm64': '-'}>
+CONFIG_SH_TIMER_CMT                             policy<{'arm64': '-'}>
+CONFIG_SH_TIMER_TMU                             policy<{'arm64': '-'}>
+CONFIG_SL28CPLD_WATCHDOG                        policy<{'arm64': '-'}>
+CONFIG_SLIC_DS26522                             policy<{'arm64': '-'}>
+CONFIG_SLIM_QCOM_NGD_CTRL                       policy<{'arm64': '-'}>
+CONFIG_SMSC_PHY                                 policy<{'arm64': 'y'}>
+CONFIG_SM_CAMCC_8250                            policy<{'arm64': '-'}>
+CONFIG_SM_DISPCC_8250                           policy<{'arm64': '-'}>
+CONFIG_SM_GCC_6115                              policy<{'arm64': '-'}>
+CONFIG_SM_GCC_6125                              policy<{'arm64': '-'}>
+CONFIG_SM_GCC_6350                              policy<{'arm64': '-'}>
+CONFIG_SM_GCC_8150                              policy<{'arm64': '-'}>
+CONFIG_SM_GCC_8250                              policy<{'arm64': '-'}>
+CONFIG_SM_GCC_8350                              policy<{'arm64': '-'}>
+CONFIG_SM_GPUCC_8150                            policy<{'arm64': '-'}>
+CONFIG_SM_GPUCC_8250                            policy<{'arm64': '-'}>
+CONFIG_SM_VIDEOCC_8150                          policy<{'arm64': '-'}>
+CONFIG_SM_VIDEOCC_8250                          policy<{'arm64': '-'}>
+CONFIG_SND_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_SND_BCM2835_SOC_I2S                      policy<{'arm64': '-'}>
+CONFIG_SND_COMPRESS_OFFLOAD                     policy<{'arm64': '-'}>
+CONFIG_SND_DMAENGINE_PCM                        policy<{'arm64': 'y'}>
+CONFIG_SND_HDA_ALIGNED_MMIO                     policy<{'arm64': '-'}>
+CONFIG_SND_HDA_TEGRA                            policy<{'arm64': '-'}>
+CONFIG_SND_HWDEP                                policy<{'arm64': 'y'}>
+CONFIG_SND_IMX_SOC                              policy<{'arm64': '-'}>
+CONFIG_SND_KIRKWOOD_SOC                         policy<{'arm64': '-'}>
+CONFIG_SND_KIRKWOOD_SOC_ARMADA370_DB            policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AIU                            policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_FIFO                       policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_FRDDR                      policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_PDM                        policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_SOUND_CARD                 policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_SPDIFIN                    policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_SPDIFOUT                   policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_TDMIN                      policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_TDMOUT                     policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_TDM_FORMATTER              policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_TDM_INTERFACE              policy<{'arm64': '-'}>
+CONFIG_SND_MESON_AXG_TODDR                      policy<{'arm64': '-'}>
+CONFIG_SND_MESON_CARD_UTILS                     policy<{'arm64': '-'}>
+CONFIG_SND_MESON_CODEC_GLUE                     policy<{'arm64': '-'}>
+CONFIG_SND_MESON_G12A_TOACODEC                  policy<{'arm64': '-'}>
+CONFIG_SND_MESON_G12A_TOHDMITX                  policy<{'arm64': '-'}>
+CONFIG_SND_MESON_GX_SOUND_CARD                  policy<{'arm64': '-'}>
+CONFIG_SND_PCM                                  policy<{'arm64': 'y'}>
+CONFIG_SND_RAWMIDI                              policy<{'arm64': 'y'}>
+CONFIG_SND_SEQ_DEVICE                           policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_ALC5632                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_APQ8016_SBC                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_COMPRESS                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_DAVINCI_MCASP                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_FSL_ASOC_CARD                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_FSL_AUD2HTX                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_I2C_AND_SPI                      policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_IMX_AUDIO_RPMSG                  policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_AUDMIX                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_CARD                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_ES8328                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_HDMI                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_PCM_DMA                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_PCM_RPMSG                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_RPMSG                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_SGTL5000                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_IMX_SPDIF                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_INTEL_KEEMBAY                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_J721E_EVM                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_LPASS_APQ8016                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_LPASS_CPU                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_LPASS_HDMI                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_LPASS_IPQ806X                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_LPASS_PLATFORM                   policy<{'arm64': '-'}>
+CONFIG_SND_SOC_LPASS_SC7180                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MAX98090                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MEDIATEK                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MESON_T9015                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MSM8996                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT2701                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT6359                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT6359_ACCDET                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT6797                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT6797_MT6351                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8173                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8183                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8183_DA7219_MAX98357A          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8183_MT6358_TS3A227E_MAX98357A policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8192                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8192_MT6359_RT1015_RT5682      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8195                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_MT8195_MT6359_RT1019_RT5682      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QCOM                             policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QCOM_COMMON                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6                            policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_ADM                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_AFE                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_AFE_CLOCKS                 policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_AFE_DAI                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_ASM                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_ASM_DAI                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_COMMON                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_CORE                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_QDSP6_ROUTING                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RCAR                             policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RK3288_HDMI_ANALOG               policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RK3399_GRU_SOUND                 policy<{'arm64': '-'}>
+CONFIG_SND_SOC_ROCKCHIP                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_ROCKCHIP_I2S                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_ROCKCHIP_MAX98090                policy<{'arm64': '-'}>
+CONFIG_SND_SOC_ROCKCHIP_PDM                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_ROCKCHIP_RT5645                  policy<{'arm64': '-'}>
+CONFIG_SND_SOC_ROCKCHIP_SPDIF                   policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT1015                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT1015P                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT5514                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT5514_SPI                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT5663                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT5677                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RT5677_SPI                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_RZ                               policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SC7180                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SDM845                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SH4_FSI                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SM8250                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SOF_IMX8                         policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SOF_IMX8M                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SOF_IMX8M_SUPPORT                policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SOF_IMX8_SUPPORT                 policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SOF_IMX_COMMON                   policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SOF_XTENSA                       policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SPRD                             policy<{'arm64': '-'}>
+CONFIG_SND_SOC_SPRD_MCDT                        policy<{'arm64': '-'}>
+CONFIG_SND_SOC_STORM                            policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA                            policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA186_DSPK                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA20_AC97                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA20_DAS                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA20_I2S                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA20_SPDIF                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA210_ADMAIF                  policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA210_AHUB                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA210_DMIC                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA210_I2S                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA30_AHUB                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA30_I2S                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_ALC5632                    policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_AUDIO_GRAPH_CARD           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_MACHINE_DRV                policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_MAX98090                   policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_RT5640                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_RT5677                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_SGTL5000                   policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_TRIMSLICE                  policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_WM8753                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_WM8903                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TEGRA_WM9712                     policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TI_EDMA_PCM                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TI_SDMA_PCM                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_TI_UDMA_PCM                      policy<{'arm64': '-'}>
+CONFIG_SND_SOC_WM8994                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_WM9712                           policy<{'arm64': '-'}>
+CONFIG_SND_SOC_WM_ADSP                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_WM_HUBS                          policy<{'arm64': '-'}>
+CONFIG_SND_SOC_XILINX_AUDIO_FORMATTER           policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_XILINX_DP                        policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_XILINX_I2S                       policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_XILINX_PL_SND_CARD               policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_XILINX_SDI                       policy<{'arm64': 'y'}>
+CONFIG_SND_SOC_XILINX_SPDIF                     policy<{'arm64': 'y'}>
+CONFIG_SND_SUN4I_CODEC                          policy<{'arm64': '-'}>
+CONFIG_SND_SUN4I_I2S                            policy<{'arm64': '-'}>
+CONFIG_SND_SUN4I_SPDIF                          policy<{'arm64': '-'}>
+CONFIG_SND_SUN50I_CODEC_ANALOG                  policy<{'arm64': '-'}>
+CONFIG_SND_SUN8I_ADDA_PR_REGMAP                 policy<{'arm64': '-'}>
+CONFIG_SND_SUN8I_CODEC                          policy<{'arm64': '-'}>
+CONFIG_SND_SUN8I_CODEC_ANALOG                   policy<{'arm64': '-'}>
+CONFIG_SND_TIMER                                policy<{'arm64': 'y'}>
+CONFIG_SND_USB_AUDIO                            policy<{'arm64': 'y'}>
+CONFIG_SNI_NETSEC                               policy<{'arm64': '-'}>
+CONFIG_SOCFPGA_FPGA_BRIDGE                      policy<{'arm64': '-'}>
+CONFIG_SOC_IMX8M                                policy<{'arm64': '-'}>
+CONFIG_SOC_RENESAS                              policy<{'arm64': '-'}>
+CONFIG_SOC_TEGRA_FLOWCTRL                       policy<{'arm64': '-'}>
+CONFIG_SOC_TEGRA_FUSE                           policy<{'arm64': '-'}>
+CONFIG_SOC_TEGRA_PMC                            policy<{'arm64': '-'}>
+CONFIG_SOC_TEGRA_POWERGATE_BPMP                 policy<{'arm64': '-'}>
+CONFIG_SPARX5_SWITCH                            policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_ACNTSA                     policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_APOLLO                     policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_AUDPTR                     policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_BNS                        policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_DECEXT                     policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_DECTLK                     policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_DUMMY                      policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_LTLK                       policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_SOFT                       policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_SPKOUT                     policy<{'arm64': '-'}>
+CONFIG_SPEAKUP_SYNTH_TXPRT                      policy<{'arm64': '-'}>
+CONFIG_SPI_ARMADA_3700                          policy<{'arm64': '-'}>
+CONFIG_SPI_BCM2835                              policy<{'arm64': '-'}>
+CONFIG_SPI_BCM2835AUX                           policy<{'arm64': '-'}>
+CONFIG_SPI_BCM_QSPI                             policy<{'arm64': '-'}>
+CONFIG_SPI_BITBANG                              policy<{'arm64': 'y'}>
+CONFIG_SPI_CADENCE                              policy<{'arm64': 'y'}>
+CONFIG_SPI_CADENCE_QUADSPI                      policy<{'arm64': 'y'}>
+CONFIG_SPI_FSL_DSPI                             policy<{'arm64': '-'}>
+CONFIG_SPI_FSL_LPSPI                            policy<{'arm64': '-'}>
+CONFIG_SPI_FSL_QUADSPI                          policy<{'arm64': '-'}>
+CONFIG_SPI_HISI_SFC                             policy<{'arm64': '-'}>
+CONFIG_SPI_IMX                                  policy<{'arm64': '-'}>
+CONFIG_SPI_MESON_SPICC                          policy<{'arm64': '-'}>
+CONFIG_SPI_MESON_SPIFC                          policy<{'arm64': '-'}>
+CONFIG_SPI_MT65XX                               policy<{'arm64': '-'}>
+CONFIG_SPI_MTK_NOR                              policy<{'arm64': '-'}>
+CONFIG_SPI_OMAP24XX                             policy<{'arm64': '-'}>
+CONFIG_SPI_ORION                                policy<{'arm64': '-'}>
+CONFIG_SPI_QCOM_GENI                            policy<{'arm64': '-'}>
+CONFIG_SPI_QCOM_QSPI                            policy<{'arm64': '-'}>
+CONFIG_SPI_QUP                                  policy<{'arm64': '-'}>
+CONFIG_SPI_ROCKCHIP_SFC                         policy<{'arm64': '-'}>
+CONFIG_SPI_RPCIF                                policy<{'arm64': '-'}>
+CONFIG_SPI_RSPI                                 policy<{'arm64': '-'}>
+CONFIG_SPI_SH_HSPI                              policy<{'arm64': '-'}>
+CONFIG_SPI_SH_MSIOF                             policy<{'arm64': '-'}>
+CONFIG_SPI_SLAVE_MT27XX                         policy<{'arm64': '-'}>
+CONFIG_SPI_SPRD                                 policy<{'arm64': '-'}>
+CONFIG_SPI_SPRD_ADI                             policy<{'arm64': '-'}>
+CONFIG_SPI_SUN4I                                policy<{'arm64': '-'}>
+CONFIG_SPI_SUN6I                                policy<{'arm64': '-'}>
+CONFIG_SPI_SYNQUACER                            policy<{'arm64': '-'}>
+CONFIG_SPI_TEGRA114                             policy<{'arm64': '-'}>
+CONFIG_SPI_TEGRA20_SFLASH                       policy<{'arm64': '-'}>
+CONFIG_SPI_TEGRA20_SLINK                        policy<{'arm64': '-'}>
+CONFIG_SPI_TEGRA210_QUAD                        policy<{'arm64': '-'}>
+CONFIG_SPI_XILINX                               policy<{'arm64': 'm'}>
+CONFIG_SPI_XLP                                  policy<{'arm64': '-'}>
+CONFIG_SPMI_MSM_PMIC_ARB                        policy<{'arm64': '-'}>
+CONFIG_SPMI_PMIC_CLKDIV                         policy<{'arm64': '-'}>
+CONFIG_SPRD_COMMON_CLK                          policy<{'arm64': '-'}>
+CONFIG_SPRD_DMA                                 policy<{'arm64': '-'}>
+CONFIG_SPRD_EFUSE                               policy<{'arm64': '-'}>
+CONFIG_SPRD_IOMMU                               policy<{'arm64': '-'}>
+CONFIG_SPRD_MBOX                                policy<{'arm64': '-'}>
+CONFIG_SPRD_SC9860_CLK                          policy<{'arm64': '-'}>
+CONFIG_SPRD_SC9863A_CLK                         policy<{'arm64': '-'}>
+CONFIG_SPRD_THERMAL                             policy<{'arm64': '-'}>
+CONFIG_SPRD_TIMER                               policy<{'arm64': '-'}>
+CONFIG_SPRD_WATCHDOG                            policy<{'arm64': '-'}>
+CONFIG_STE10XP                                  policy<{'arm64': 'y'}>
+CONFIG_STMP_DEVICE                              policy<{'arm64': '-'}>
+CONFIG_STP                                      policy<{'arm64': 'y'}>
+CONFIG_STUB_CLK_HI3660                          policy<{'arm64': '-'}>
+CONFIG_STUB_CLK_HI6220                          policy<{'arm64': '-'}>
+CONFIG_SUN4I_EMAC                               policy<{'arm64': '-'}>
+CONFIG_SUN4I_GPADC                              policy<{'arm64': '-'}>
+CONFIG_SUN4I_TIMER                              policy<{'arm64': '-'}>
+CONFIG_SUN50I_A100_CCU                          policy<{'arm64': '-'}>
+CONFIG_SUN50I_A100_R_CCU                        policy<{'arm64': '-'}>
+CONFIG_SUN50I_A64_CCU                           policy<{'arm64': '-'}>
+CONFIG_SUN50I_DE2_BUS                           policy<{'arm64': '-'}>
+CONFIG_SUN50I_ERRATUM_UNKNOWN1                  policy<{'arm64': '-'}>
+CONFIG_SUN50I_H616_CCU                          policy<{'arm64': '-'}>
+CONFIG_SUN50I_H6_CCU                            policy<{'arm64': '-'}>
+CONFIG_SUN50I_H6_R_CCU                          policy<{'arm64': '-'}>
+CONFIG_SUN50I_IOMMU                             policy<{'arm64': '-'}>
+CONFIG_SUN6I_MSGBOX                             policy<{'arm64': '-'}>
+CONFIG_SUN8I_A83T_CCU                           policy<{'arm64': '-'}>
+CONFIG_SUN8I_DE2_CCU                            policy<{'arm64': '-'}>
+CONFIG_SUN8I_H3_CCU                             policy<{'arm64': '-'}>
+CONFIG_SUN8I_R_CCU                              policy<{'arm64': '-'}>
+CONFIG_SUN8I_THERMAL                            policy<{'arm64': '-'}>
+CONFIG_SUNRPC                                   policy<{'arm64': 'y'}>
+CONFIG_SUNRPC_GSS                               policy<{'arm64': 'y'}>
+CONFIG_SUNXI_CCU                                policy<{'arm64': '-'}>
+CONFIG_SUNXI_MBUS                               policy<{'arm64': '-'}>
+CONFIG_SUNXI_RSB                                policy<{'arm64': '-'}>
+CONFIG_SUNXI_SRAM                               policy<{'arm64': '-'}>
+CONFIG_SUNXI_WATCHDOG                           policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A774A1                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A774B1                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A774C0                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A774E1                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A7795                             policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77960                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77961                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77965                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77970                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77980                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77990                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A77995                            policy<{'arm64': '-'}>
+CONFIG_SYSC_R8A779A0                            policy<{'arm64': '-'}>
+CONFIG_SYSC_RCAR                                policy<{'arm64': '-'}>
+CONFIG_SYS_SUPPORTS_SH_CMT                      policy<{'arm64': '-'}>
+CONFIG_SYS_SUPPORTS_SH_TMU                      policy<{'arm64': '-'}>
+CONFIG_TCG_TIS_SYNQUACER                        policy<{'arm64': '-'}>
+CONFIG_TEE_BNXT_FW                              policy<{'arm64': '-'}>
+CONFIG_TEGRA20_APB_DMA                          policy<{'arm64': '-'}>
+CONFIG_TEGRA210_ADMA                            policy<{'arm64': '-'}>
+CONFIG_TEGRA210_EMC                             policy<{'arm64': '-'}>
+CONFIG_TEGRA210_EMC_TABLE                       policy<{'arm64': '-'}>
+CONFIG_TEGRA_ACONNECT                           policy<{'arm64': '-'}>
+CONFIG_TEGRA_AHB                                policy<{'arm64': '-'}>
+CONFIG_TEGRA_BPMP                               policy<{'arm64': '-'}>
+CONFIG_TEGRA_BPMP_THERMAL                       policy<{'arm64': '-'}>
+CONFIG_TEGRA_CLK_DFLL                           policy<{'arm64': '-'}>
+CONFIG_TEGRA_GMI                                policy<{'arm64': '-'}>
+CONFIG_TEGRA_HOST1X                             policy<{'arm64': '-'}>
+CONFIG_TEGRA_HOST1X_FIREWALL                    policy<{'arm64': '-'}>
+CONFIG_TEGRA_HSP_MBOX                           policy<{'arm64': '-'}>
+CONFIG_TEGRA_IOMMU_SMMU                         policy<{'arm64': '-'}>
+CONFIG_TEGRA_IVC                                policy<{'arm64': '-'}>
+CONFIG_TEGRA_MC                                 policy<{'arm64': '-'}>
+CONFIG_TEGRA_SOCTHERM                           policy<{'arm64': '-'}>
+CONFIG_TEGRA_TIMER                              policy<{'arm64': '-'}>
+CONFIG_TEGRA_VDE                                policy<{'arm64': '-'}>
+CONFIG_TEGRA_WATCHDOG                           policy<{'arm64': '-'}>
+CONFIG_TEST_UBSAN                               policy<{'arm64': '-'}>
+CONFIG_THUNDERX2_PMU                            policy<{'arm64': '-'}>
+CONFIG_TIMER_IMX_SYS_CTR                        policy<{'arm64': '-'}>
+CONFIG_TI_AM335X_ADC                            policy<{'arm64': '-'}>
+CONFIG_TI_AM65_CPSW_TAS                         policy<{'arm64': '-'}>
+CONFIG_TI_DAVINCI_MDIO                          policy<{'arm64': '-'}>
+CONFIG_TI_K3_AM65_CPSW_NUSS                     policy<{'arm64': '-'}>
+CONFIG_TI_K3_AM65_CPSW_SWITCHDEV                policy<{'arm64': '-'}>
+CONFIG_TI_K3_AM65_CPTS                          policy<{'arm64': '-'}>
+CONFIG_TI_K3_DSP_REMOTEPROC                     policy<{'arm64': '-'}>
+CONFIG_TI_K3_PSIL                               policy<{'arm64': '-'}>
+CONFIG_TI_K3_R5_REMOTEPROC                      policy<{'arm64': '-'}>
+CONFIG_TI_K3_RINGACC                            policy<{'arm64': '-'}>
+CONFIG_TI_K3_SOCINFO                            policy<{'arm64': '-'}>
+CONFIG_TI_K3_UDMA                               policy<{'arm64': '-'}>
+CONFIG_TI_K3_UDMA_GLUE_LAYER                    policy<{'arm64': '-'}>
+CONFIG_TI_MESSAGE_MANAGER                       policy<{'arm64': '-'}>
+CONFIG_TI_PRUSS                                 policy<{'arm64': '-'}>
+CONFIG_TI_PRUSS_INTC                            policy<{'arm64': '-'}>
+CONFIG_TI_SCI_CLK                               policy<{'arm64': '-'}>
+CONFIG_TI_SCI_CLK_PROBE_FROM_FW                 policy<{'arm64': '-'}>
+CONFIG_TI_SCI_INTA_IRQCHIP                      policy<{'arm64': '-'}>
+CONFIG_TI_SCI_INTA_MSI_DOMAIN                   policy<{'arm64': '-'}>
+CONFIG_TI_SCI_INTR_IRQCHIP                      policy<{'arm64': '-'}>
+CONFIG_TI_SCI_PM_DOMAINS                        policy<{'arm64': '-'}>
+CONFIG_TI_SCI_PROTOCOL                          policy<{'arm64': '-'}>
+CONFIG_TI_ST                                    policy<{'arm64': 'y'}>
+CONFIG_TI_SYSCON_CLK                            policy<{'arm64': '-'}>
+CONFIG_TOUCHSCREEN_IPROC                        policy<{'arm64': '-'}>
+CONFIG_TOUCHSCREEN_RASPBERRYPI_FW               policy<{'arm64': '-'}>
+CONFIG_TOUCHSCREEN_SUN4I                        policy<{'arm64': '-'}>
+CONFIG_TOUCHSCREEN_TI_AM335X_TSC                policy<{'arm64': '-'}>
+CONFIG_TURRIS_MOX_RWTM                          policy<{'arm64': '-'}>
+CONFIG_TYPEC_QCOM_PMIC                          policy<{'arm64': '-'}>
+CONFIG_UBIFS_FS                                 policy<{'arm64': 'y'}>
+CONFIG_UBSAN_ALIGNMENT                          policy<{'arm64': '-'}>
+CONFIG_UBSAN_BOOL                               policy<{'arm64': '-'}>
+CONFIG_UBSAN_BOUNDS                             policy<{'arm64': '-'}>
+CONFIG_UBSAN_DIV_ZERO                           policy<{'arm64': '-'}>
+CONFIG_UBSAN_ENUM                               policy<{'arm64': '-'}>
+CONFIG_UBSAN_ONLY_BOUNDS                        policy<{'arm64': '-'}>
+CONFIG_UBSAN_SANITIZE_ALL                       policy<{'arm64': '-'}>
+CONFIG_UBSAN_SHIFT                              policy<{'arm64': '-'}>
+CONFIG_UBSAN_TRAP                               policy<{'arm64': '-'}>
+CONFIG_UBSAN_UNREACHABLE                        policy<{'arm64': '-'}>
+CONFIG_UIO                                      policy<{'arm64': 'y'}>
+CONFIG_UIO_XILINX_AI_ENGINE                     policy<{'arm64': 'm'}>
+CONFIG_UIO_XILINX_APM                           policy<{'arm64': 'y'}>
+CONFIG_USB_BRCMSTB                              policy<{'arm64': '-'}>
+CONFIG_USB_CDNS3_IMX                            policy<{'arm64': '-'}>
+CONFIG_USB_CDNS3_TI                             policy<{'arm64': '-'}>
+CONFIG_USB_CONFIGFS                             policy<{'arm64': 'y'}>
+CONFIG_USB_DWC2_DUAL_ROLE                       policy<{'arm64': 'n'}>
+CONFIG_USB_DWC2_PERIPHERAL                      policy<{'arm64': 'n'}>
+CONFIG_USB_DWC3                                 policy<{'arm64': 'y'}>
+CONFIG_USB_DWC3_HAPS                            policy<{'arm64': 'y'}>
+CONFIG_USB_DWC3_IMX8MP                          policy<{'arm64': '-'}>
+CONFIG_USB_DWC3_KEYSTONE                        policy<{'arm64': '-'}>
+CONFIG_USB_DWC3_MESON_G12A                      policy<{'arm64': '-'}>
+CONFIG_USB_DWC3_OF_SIMPLE                       policy<{'arm64': 'y'}>
+CONFIG_USB_DWC3_OTG                             policy<{'arm64': 'n'}>
+CONFIG_USB_DWC3_QCOM                            policy<{'arm64': '-'}>
+CONFIG_USB_DWC3_ULPI                            policy<{'arm64': '-'}>
+CONFIG_USB_DWC3_XILINX                          policy<{'arm64': 'y'}>
+CONFIG_USB_EHCI_BRCMSTB                         policy<{'arm64': '-'}>
+CONFIG_USB_EHCI_HCD_ORION                       policy<{'arm64': '-'}>
+CONFIG_USB_EHCI_TEGRA                           policy<{'arm64': '-'}>
+CONFIG_USB_EMXX                                 policy<{'arm64': '-'}>
+CONFIG_USB_F_ACM                                policy<{'arm64': 'y'}>
+CONFIG_USB_F_ECM                                policy<{'arm64': 'y'}>
+CONFIG_USB_F_EEM                                policy<{'arm64': 'y'}>
+CONFIG_USB_F_FS                                 policy<{'arm64': 'y'}>
+CONFIG_USB_F_HID                                policy<{'arm64': 'y'}>
+CONFIG_USB_F_MASS_STORAGE                       policy<{'arm64': 'y'}>
+CONFIG_USB_F_MIDI                               policy<{'arm64': 'y'}>
+CONFIG_USB_F_NCM                                policy<{'arm64': 'y'}>
+CONFIG_USB_F_OBEX                               policy<{'arm64': 'y'}>
+CONFIG_USB_F_PRINTER                            policy<{'arm64': 'y'}>
+CONFIG_USB_F_RNDIS                              policy<{'arm64': 'y'}>
+CONFIG_USB_F_SERIAL                             policy<{'arm64': 'y'}>
+CONFIG_USB_F_SS_LB                              policy<{'arm64': 'y'}>
+CONFIG_USB_F_SUBSET                             policy<{'arm64': 'y'}>
+CONFIG_USB_F_UAC1                               policy<{'arm64': 'y'}>
+CONFIG_USB_F_UAC1_LEGACY                        policy<{'arm64': 'y'}>
+CONFIG_USB_F_UAC2                               policy<{'arm64': 'y'}>
+CONFIG_USB_F_UVC                                policy<{'arm64': 'y'}>
+CONFIG_USB_GADGET                               policy<{'arm64': 'y'}>
+CONFIG_USB_GADGET_XILINX                        policy<{'arm64': 'y'}>
+CONFIG_USB_LIBCOMPOSITE                         policy<{'arm64': 'y'}>
+CONFIG_USB_MTU3                                 policy<{'arm64': '-'}>
+CONFIG_USB_MTU3_DEBUG                           policy<{'arm64': '-'}>
+CONFIG_USB_MTU3_DUAL_ROLE                       policy<{'arm64': '-'}>
+CONFIG_USB_MTU3_GADGET                          policy<{'arm64': '-'}>
+CONFIG_USB_MTU3_HOST                            policy<{'arm64': '-'}>
+CONFIG_USB_MUSB_MEDIATEK                        policy<{'arm64': '-'}>
+CONFIG_USB_MUSB_SUNXI                           policy<{'arm64': '-'}>
+CONFIG_USB_MXS_PHY                              policy<{'arm64': '-'}>
+CONFIG_USB_NET_AX88179_178A                     policy<{'arm64': 'y'}>
+CONFIG_USB_NET_AX8817X                          policy<{'arm64': 'y'}>
+CONFIG_USB_NET_CDCETHER                         policy<{'arm64': 'y'}>
+CONFIG_USB_NET_CDC_NCM                          policy<{'arm64': 'y'}>
+CONFIG_USB_NET_CDC_SUBSET                       policy<{'arm64': 'y'}>
+CONFIG_USB_NET_CDC_SUBSET_ENABLE                policy<{'arm64': 'y'}>
+CONFIG_USB_NET_DRIVERS                          policy<{'arm64': 'y'}>
+CONFIG_USB_NET_NET1080                          policy<{'arm64': 'y'}>
+CONFIG_USB_NET_ZAURUS                           policy<{'arm64': 'y'}>
+CONFIG_USB_OTG_FSM                              policy<{'arm64': 'y'}>
+CONFIG_USB_RENESAS_USB3                         policy<{'arm64': '-'}>
+CONFIG_USB_RENESAS_USBHS                        policy<{'arm64': '-'}>
+CONFIG_USB_RENESAS_USBHS_HCD                    policy<{'arm64': '-'}>
+CONFIG_USB_RENESAS_USBHS_UDC                    policy<{'arm64': '-'}>
+CONFIG_USB_STORAGE                              policy<{'arm64': 'y'}>
+CONFIG_USB_TEGRA_PHY                            policy<{'arm64': '-'}>
+CONFIG_USB_TEGRA_XUDC                           policy<{'arm64': '-'}>
+CONFIG_USB_UAS                                  policy<{'arm64': 'y'}>
+CONFIG_USB_USB2244                              policy<{'arm64': 'm'}>
+CONFIG_USB_USB5744                              policy<{'arm64': 'm'}>
+CONFIG_USB_USBNET                               policy<{'arm64': 'y'}>
+CONFIG_USB_U_AUDIO                              policy<{'arm64': 'y'}>
+CONFIG_USB_U_ETHER                              policy<{'arm64': 'y'}>
+CONFIG_USB_U_SERIAL                             policy<{'arm64': 'y'}>
+CONFIG_USB_VIDEO_CLASS                          policy<{'arm64': 'y'}>
+CONFIG_USB_XHCI_HISTB                           policy<{'arm64': '-'}>
+CONFIG_USB_XHCI_MTK                             policy<{'arm64': '-'}>
+CONFIG_USB_XHCI_MVEBU                           policy<{'arm64': '-'}>
+CONFIG_USB_XHCI_PLATFORM                        policy<{'arm64': 'y'}>
+CONFIG_USB_XHCI_RCAR                            policy<{'arm64': '-'}>
+CONFIG_USB_XHCI_TEGRA                           policy<{'arm64': '-'}>
+CONFIG_USB_ZERO_HNPTEST                         policy<{'arm64': 'n'}>
+CONFIG_V4L2_ASYNC                               policy<{'arm64': 'y'}>
+CONFIG_V4L2_FWNODE                              policy<{'arm64': 'y'}>
+CONFIG_V4L2_H264                                policy<{'arm64': '-'}>
+CONFIG_V4L2_JPEG_HELPER                         policy<{'arm64': '-'}>
+CONFIG_V4L2_MEM2MEM_DEV                         policy<{'arm64': 'y'}>
+CONFIG_VCHIQ_CDEV                               policy<{'arm64': '-'}>
+CONFIG_VERSAL_SYSMON                            policy<{'arm64': 'y'}>
+CONFIG_VETH                                     policy<{'arm64': 'y'}>
+CONFIG_VFIO_FSL_MC                              policy<{'arm64': '-'}>
+CONFIG_VFIO_PLATFORM_BCMFLEXRM_RESET            policy<{'arm64': '-'}>
+CONFIG_VIDEOBUF2_CORE                           policy<{'arm64': 'y'}>
+CONFIG_VIDEOBUF2_DMA_CONTIG                     policy<{'arm64': 'y'}>
+CONFIG_VIDEOBUF2_DMA_SG                         policy<{'arm64': 'y'}>
+CONFIG_VIDEOBUF2_MEMOPS                         policy<{'arm64': 'y'}>
+CONFIG_VIDEOBUF2_V4L2                           policy<{'arm64': 'y'}>
+CONFIG_VIDEOBUF2_VMALLOC                        policy<{'arm64': 'y'}>
+CONFIG_VIDEO_ALLEGRO_DVT                        policy<{'arm64': 'n'}>
+CONFIG_VIDEO_AP1302                             policy<{'arm64': 'm'}>
+CONFIG_VIDEO_AR1335                             policy<{'arm64': 'm'}>
+CONFIG_VIDEO_BCM2835                            policy<{'arm64': '-'}>
+CONFIG_VIDEO_CODA                               policy<{'arm64': '-'}>
+CONFIG_VIDEO_DEV                                policy<{'arm64': 'y'}>
+CONFIG_VIDEO_HANTRO                             policy<{'arm64': '-'}>
+CONFIG_VIDEO_HANTRO_IMX8M                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_HANTRO_ROCKCHIP                    policy<{'arm64': '-'}>
+CONFIG_VIDEO_IMX219                             policy<{'arm64': 'y'}>
+CONFIG_VIDEO_IMX7_CSI                           policy<{'arm64': '-'}>
+CONFIG_VIDEO_IMX8_JPEG                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_IMX_MEDIA                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_IMX_PXP                            policy<{'arm64': '-'}>
+CONFIG_VIDEO_MEDIATEK_VPU                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_MESON_GE2D                         policy<{'arm64': '-'}>
+CONFIG_VIDEO_MESON_VDEC                         policy<{'arm64': '-'}>
+CONFIG_VIDEO_QCOM_CAMSS                         policy<{'arm64': '-'}>
+CONFIG_VIDEO_QCOM_VENUS                         policy<{'arm64': '-'}>
+CONFIG_VIDEO_RCAR_CSI2                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_RCAR_DRIF                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_RCAR_VIN                           policy<{'arm64': '-'}>
+CONFIG_VIDEO_RENESAS_FCP                        policy<{'arm64': '-'}>
+CONFIG_VIDEO_RENESAS_FDP1                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_RENESAS_JPU                        policy<{'arm64': '-'}>
+CONFIG_VIDEO_RENESAS_VSP1                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_ROCKCHIP_ISP1                      policy<{'arm64': '-'}>
+CONFIG_VIDEO_ROCKCHIP_RGA                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_ROCKCHIP_VDEC                      policy<{'arm64': '-'}>
+CONFIG_VIDEO_SUN4I_CSI                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_SUN6I_CSI                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_SUN8I_DEINTERLACE                  policy<{'arm64': '-'}>
+CONFIG_VIDEO_SUN8I_ROTATE                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_SUNXI                              policy<{'arm64': '-'}>
+CONFIG_VIDEO_SUNXI_CEDRUS                       policy<{'arm64': '-'}>
+CONFIG_VIDEO_TEGRA                              policy<{'arm64': '-'}>
+CONFIG_VIDEO_TEGRA_TPG                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_TI_CAL                             policy<{'arm64': '-'}>
+CONFIG_VIDEO_TI_CAL_MC                          policy<{'arm64': '-'}>
+CONFIG_VIDEO_V4L2                               policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX                             policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_AXI4S_BROADCASTER           policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_AXI4S_SUBSETCONV            policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_AXI4S_SWITCH                policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_CFA                         policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_CRESAMPLE                   policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_CSI2RXSS                    policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_DEMOSAIC                    policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_DPRXSS                      policy<{'arm64': 'n'}>
+CONFIG_VIDEO_XILINX_GAMMA                       policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_HDMI21RXSS                  policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_HLS                         policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_M2M                         policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_MULTISCALER                 policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_REMAPPER                    policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_RGB2YUV                     policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_SCALER                      policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_SCD                         policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_SDIRXSS                     policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_SWITCH                      policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_TPG                         policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_VPSS_CSC                    policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_VPSS_SCALER                 policy<{'arm64': 'y'}>
+CONFIG_VIDEO_XILINX_VTC                         policy<{'arm64': 'y'}>
+CONFIG_VISCONTI_WATCHDOG                        policy<{'arm64': '-'}>
+CONFIG_VITESSE_PHY                              policy<{'arm64': 'y'}>
+CONFIG_VLAN_8021Q                               policy<{'arm64': 'y'}>
+CONFIG_VMXNET3                                  policy<{'arm64': 'm'}>
+CONFIG_W1                                       policy<{'arm64': 'y'}>
+CONFIG_W1_MASTER_AMD_AXI                        policy<{'arm64': 'y'}>
+CONFIG_W1_MASTER_MXC                            policy<{'arm64': '-'}>
+CONFIG_XENFS                                    policy<{'arm64': 'y'}>
+CONFIG_XEN_DEV_EVTCHN                           policy<{'arm64': 'y'}>
+CONFIG_XEN_PRIVCMD                              policy<{'arm64': 'y'}>
+CONFIG_XEN_PVCALLS_BACKEND                      policy<{'arm64': 'y'}>
+CONFIG_XEN_PVCALLS_FRONTEND                     policy<{'arm64': 'y'}>
+CONFIG_XFRM_ALGO                                policy<{'arm64': 'y'}>
+CONFIG_XFRM_MIGRATE                             policy<{'arm64': 'y'}>
+CONFIG_XFRM_USER                                policy<{'arm64': 'y'}>
+CONFIG_XGENE_DMA                                policy<{'arm64': '-'}>
+CONFIG_XGENE_PMU                                policy<{'arm64': '-'}>
+CONFIG_XGENE_SLIMPRO_MBOX                       policy<{'arm64': '-'}>
+CONFIG_XILINX_AFI_FPGA                          policy<{'arm64': 'y'}>
+CONFIG_XILINX_AIE                               policy<{'arm64': 'y'}>
+CONFIG_XILINX_AMS                               policy<{'arm64': 'y'}>
+CONFIG_XILINX_APF                               policy<{'arm64': 'y'}>
+CONFIG_XILINX_AXI_EMAC                          policy<{'arm64': 'y'}>
+CONFIG_XILINX_AXI_EMAC_HWTSTAMP                 policy<{'arm64': 'n'}>
+CONFIG_XILINX_DMA                               policy<{'arm64': 'y'}>
+CONFIG_XILINX_DMATEST                           policy<{'arm64': 'n'}>
+CONFIG_XILINX_DMA_APF                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_DPU                               policy<{'arm64': 'n'}>
+CONFIG_XILINX_EMACLITE                          policy<{'arm64': 'y'}>
+CONFIG_XILINX_FCLK                              policy<{'arm64': 'y'}>
+CONFIG_XILINX_FLEX_PM                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_FRMBUF                            policy<{'arm64': 'y'}>
+CONFIG_XILINX_GMII2RGMII                        policy<{'arm64': 'y'}>
+CONFIG_XILINX_JESD204B                          policy<{'arm64': 'y'}>
+CONFIG_XILINX_JESD204B_PHY                      policy<{'arm64': 'y'}>
+CONFIG_XILINX_PHY                               policy<{'arm64': 'y'}>
+CONFIG_XILINX_PR_DECOUPLER                      policy<{'arm64': 'y'}>
+CONFIG_XILINX_PS_PCIE_DMA                       policy<{'arm64': 'y'}>
+CONFIG_XILINX_PS_PCIE_DMA_TEST                  policy<{'arm64': 'n'}>
+CONFIG_XILINX_SDFEC                             policy<{'arm64': 'y'}>
+CONFIG_XILINX_TRAFGEN                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN                               policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN_CB                            policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN_PTP                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN_QBR                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN_QBV                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN_QCI                           policy<{'arm64': 'y'}>
+CONFIG_XILINX_TSN_SWITCH                        policy<{'arm64': 'y'}>
+CONFIG_XILINX_VDMATEST                          policy<{'arm64': 'n'}>
+CONFIG_XILINX_WATCHDOG                          policy<{'arm64': 'y'}>
+CONFIG_XILINX_XADC                              policy<{'arm64': 'y'}>
+CONFIG_XILINX_ZYNQMP_DMA                        policy<{'arm64': 'y'}>
+CONFIG_XILINX_ZYNQMP_DPDMA                      policy<{'arm64': 'y'}>
+CONFIG_XLNX_EVENT_MANAGER                       policy<{'arm64': 'y'}>
+CONFIG_XLNX_SEC_CFG                             policy<{'arm64': 'y'}>
+CONFIG_XLNX_SYNC                                policy<{'arm64': 'y'}>
+CONFIG_XLNX_TSMUX                               policy<{'arm64': 'n'}>
+CONFIG_XOR_BLOCKS                               policy<{'arm64': 'y'}>
+CONFIG_XROE_FRAMER                              policy<{'arm64': 'n'}>
+CONFIG_XROE_TRAFFIC_GEN                         policy<{'arm64': 'n'}>
+CONFIG_ZSTD_COMPRESS                            policy<{'arm64': 'y'}>
+CONFIG_ZYNQMP_FIRMWARE_DEBUG                    policy<{'arm64': 'y'}>
+CONFIG_ZYNQMP_FIRMWARE_SECURE                   policy<{'arm64': 'y'}>
+CONFIG_ZYNQMP_R5_REMOTEPROC                     policy<{'arm64': 'm'}>
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/control.d/flavour-control.stub
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/control.d/flavour-control.stub
@@ -0,0 +1,142 @@
+# Items that get replaced:
+# FLAVOUR
+# DESC
+# ARCH
+# SUPPORTED
+# TARGET
+# BOOTLOADER
+# =PROVIDES=
+#
+# Items marked with =FOO= are optional
+#
+# This file describes the template for packages that are created for each flavour
+# in debian/control.d/vars.*
+#
+# This file gets edited in a couple of places. See the debian/control.stub rule in
+# debian/rules. PGGVER, ABINUM, and SRCPKGNAME are all converted in the
+# process of creating debian/control.
+#
+# The flavour specific strings (ARCH, DESC, etc) are converted using values from the various
+# flavour files in debian/control.d/vars.*
+#
+# XXX: Leave the blank line before the first package!!
+
+Package: linux-image=SIGN-ME-PKG=-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Provides: linux-image, fuse-module, =PROVIDES=${linux:rprovides}
+Depends: ${misc:Depends}, ${shlibs:Depends}, kmod, linux-base (>= 4.5ubuntu1~16.04.1), linux-modules-PKGVER-ABINUM-FLAVOUR
+Recommends: BOOTLOADER, initramfs-tools | linux-initramfs-tool
+Breaks: flash-kernel (<< 3.104ubuntu20) [arm64 armhf], s390-tools (<< 2.3.0-0ubuntu3) [s390x]
+Conflicts: linux-image=SIGN-PEER-PKG=-PKGVER-ABINUM-FLAVOUR
+Suggests: fdutils, linux-doc | SRCPKGNAME-source-PKGVER, SRCPKGNAME-tools, linux-headers-PKGVER-ABINUM-FLAVOUR, linux-modules-extra-PKGVER-ABINUM-FLAVOUR
+Description: Linux kernel image for version PKGVER on DESC
+ This package contains the=SIGN-ME-TXT= Linux kernel image for version PKGVER on
+ DESC.
+ .
+ Supports SUPPORTED processors.
+ .
+ TARGET
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-FLAVOUR meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-modules-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-image-PKGVER-ABINUM-FLAVOUR | linux-image-unsigned-PKGVER-ABINUM-FLAVOUR
+Built-Using: ${linux:BuiltUsing}
+Description: Linux kernel extra modules for version PKGVER on DESC
+ Contains the corresponding System.map file, the modules built by the
+ packager, and scripts that try to ensure that the system is not left in an
+ unbootable state after an update.
+ .
+ Supports SUPPORTED processors.
+ .
+ TARGET
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-FLAVOUR meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-modules-extra-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-image-PKGVER-ABINUM-FLAVOUR | linux-image-unsigned-PKGVER-ABINUM-FLAVOUR, crda | wireless-crda
+Description: Linux kernel extra modules for version PKGVER on DESC
+ This package contains the Linux kernel extra modules for version PKGVER on
+ DESC.
+ .
+ Also includes the corresponding System.map file, the modules built by the
+ packager, and scripts that try to ensure that the system is not left in an
+ unbootable state after an update.
+ .
+ Supports SUPPORTED processors.
+ .
+ TARGET
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-FLAVOUR meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-headers-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, SRCPKGNAME-headers-PKGVER-ABINUM, ${shlibs:Depends}
+Provides: linux-headers, linux-headers-3.0
+Description: Linux kernel headers for version PKGVER on DESC
+ This package provides kernel header files for version PKGVER on
+ DESC.
+ .
+ This is for sites that want the latest kernel headers.  Please read
+ /usr/share/doc/linux-headers-PKGVER-ABINUM/debian.README.gz for details.
+
+Package: linux-image=SIGN-ME-PKG=-PKGVER-ABINUM-FLAVOUR-dbgsym
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}
+Provides: linux-debug
+Description: Linux kernel debug image for version PKGVER on DESC
+ This package provides the=SIGN-ME-TXT= kernel debug image for version PKGVER on
+ DESC.
+ .
+ This is for sites that wish to debug the kernel.
+ .
+ The kernel image contained in this package is NOT meant to boot from. It
+ is uncompressed, and unstripped. This package also includes the
+ unstripped modules.
+
+Package: linux-tools-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, SRCPKGNAME-tools-PKGVER-ABINUM
+Description: Linux kernel version specific tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version PKGVER-ABINUM on
+ =HUMAN=.
+
+Package: linux-cloud-tools-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, SRCPKGNAME-cloud-tools-PKGVER-ABINUM
+Description: Linux kernel version specific cloud tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools for cloud for version PKGVER-ABINUM on
+ =HUMAN=.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/control.d/vars.xilinx-zynqmp
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/control.d/vars.xilinx-zynqmp
@@ -0,0 +1,6 @@
+arch="arm64"
+supported="Xilinx ZYNQ Ultrascale+"
+target="Geared toward desktop and server systems."
+desc="=HUMAN= SMP"
+bootloader="grub-pc [amd64] | grub-efi-amd64 [amd64] | grub-efi-ia32 [amd64] | grub [amd64] | lilo [amd64] | flash-kernel [armhf arm64] | grub-efi-arm64 [arm64] | grub-efi-arm [armhf] | grub-ieee1275 [ppc64el]"
+provides="kvm-api-4, redhat-cluster-modules, ivtv-modules, virtualbox-guest-modules [amd64]"
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/control.stub.in
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/control.stub.in
@@ -0,0 +1,110 @@
+Source: SRCPKGNAME
+Section: devel
+Priority: optional
+Maintainer: Ubuntu Kernel Team <kernel-team@lists.ubuntu.com>
+Standards-Version: 3.9.4.0
+Build-Depends:
+ debhelper-compat (= 10),
+ cpio,
+ kmod <!stage1>,
+ makedumpfile [amd64] <!stage1>,
+ libcap-dev <!stage1>,
+ libelf-dev <!stage1>,
+ libnewt-dev <!stage1>,
+ libiberty-dev <!stage1>,
+ default-jdk-headless <!stage1>,
+ java-common <!stage1>,
+ rsync <!stage1>,
+ libdw-dev <!stage1>,
+ libpci-dev <!stage1>,
+ pkg-config <!stage1>,
+ python3-dev <!stage1>,
+ flex <!stage1>,
+ bison <!stage1>,
+ libunwind8-dev [amd64 arm64 armhf ppc64el] <!stage1>,
+ liblzma-dev <!stage1>,
+ openssl <!stage1>,
+ libssl-dev <!stage1>,
+ libaudit-dev <!stage1>,
+ bc <!stage1>,
+ gawk <!stage1>,
+ libudev-dev <!stage1>,
+ autoconf <!stage1>,
+ automake <!stage1>,
+ libtool <!stage1>,
+ uuid-dev <!stage1>,
+ libnuma-dev [amd64 arm64 ppc64el s390x] <!stage1>,
+ dkms <!stage1>,
+ dwarfdump <!stage1>,
+ curl <!stage1>,
+ zstd [amd64 s390x] <!stage1>,
+ pahole [amd64 arm64 armhf ppc64el s390x riscv64] | dwarves (>= 1.21) [amd64 arm64 armhf ppc64el s390x riscv64] <!stage1>,
+Build-Depends-Indep:
+ xmlto <!stage1>,
+ docbook-utils <!stage1>,
+ ghostscript <!stage1>,
+ fig2dev <!stage1>,
+ bzip2 <!stage1>,
+ sharutils <!stage1>,
+ asciidoc <!stage1>,
+ python3-sphinx <!stage1>,
+ python3-sphinx-rtd-theme <!stage1>,
+ fontconfig <!stage1>,
+ python3-docutils <!stage1>,
+ imagemagick <!stage1>,
+ graphviz <!stage1>,
+ dvipng <!stage1>,
+ fonts-noto-cjk <!stage1>,
+ latexmk <!stage1>,
+ librsvg2-bin <!stage1>,
+Vcs-Git: git://git.launchpad.net/~canonical-kernel/ubuntu/+source/linux-xilinx-zynqmp/+git/=SERIES=
+XS-Testsuite: autopkgtest
+#XS-Testsuite-Depends: gcc-4.7 binutils
+
+Package: SRCPKGNAME-headers-PKGVER-ABINUM
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, coreutils
+Description: Header files related to Linux kernel version PKGVER
+ This package provides kernel header files for version PKGVER, for sites
+ that want the latest kernel headers. Please read
+ /usr/share/doc/SRCPKGNAME-headers-PKGVER-ABINUM/debian.README.gz for details
+
+Package: SRCPKGNAME-tools-common
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, lsb-release
+Description: Linux kernel version specific tools for version PKGVER
+ This package provides the architecture independent parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version PKGVER.
+
+Package: SRCPKGNAME-tools-PKGVER-ABINUM
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-tools-common
+Description: Linux kernel version specific tools for version PKGVER-ABINUM
+ This package provides the architecture dependant parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version PKGVER-ABINUM on
+ =HUMAN=.
+ You probably want to install linux-tools-PKGVER-ABINUM-<flavour>.
+
+Package: SRCPKGNAME-tools-host
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, python3
+Description: Linux kernel VM host tools
+ This package provides kernel tools useful for VM hosts.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/copyright
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/copyright
@@ -0,0 +1,29 @@
+This is the Ubuntu prepackaged version of the Linux kernel.
+Linux was written by Linus Torvalds <Linus.Torvalds@cs.Helsinki.FI>
+and others.
+
+This package was put together by the Ubuntu Kernel Team, from
+sources retrieved from upstream linux git.
+The sources may be found at most Linux ftp sites, including 
+ftp://ftp.kernel.org/pub/linux/kernel/
+
+This package is currently maintained by the
+Ubuntu Kernel Team <ubuntu-kernel@lists.ubuntu.com>
+
+Linux is copyrighted by Linus Torvalds and others.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; version 2 dated June, 1991.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program; if not, write to the Free Software
+   Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+On Ubuntu Linux systems, the complete text of the GNU General
+Public License v2 can be found in `/usr/share/common-licenses/GPL-2'.
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/dkms-versions
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/dkms-versions
@@ -0,0 +1 @@
+zfs-linux 2.1.5-1ubuntu6~22.04.5 modulename=zfs debpath=pool/universe/z/%package%/zfs-dkms_%version%_all.deb arch=amd64 arch=arm64 arch=ppc64el arch=s390x rprovides=spl-modules rprovides=spl-dkms rprovides=zfs-modules rprovides=zfs-dkms
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/etc/kernelconfig
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/etc/kernelconfig
@@ -0,0 +1,7 @@
+if [ "$variant" = "ports" ]; then
+	archs=""
+	family='ports'
+else
+	archs="arm64"
+	family='ubuntu'
+fi
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/etc/update.conf
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/etc/update.conf
@@ -0,0 +1,7 @@
+# WARNING: we do not create update.conf when we are not a
+# derivative. Various cranky components make use of this.
+# If we start unconditionally creating update.conf we need
+# to fix at least cranky close and cranky rebase.
+RELEASE_REPO=git://git.launchpad.net/~ubuntu-kernel/ubuntu/+source/linux/+git/jammy
+SOURCE_RELEASE_BRANCH=master-next
+DEBIAN_MASTER=debian.master
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/modprobe.d/common.conf
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/modprobe.d/common.conf
@@ -0,0 +1,3 @@
+# LP:1434842 -- disable OSS drivers by default to allow pulseaudio to emulate
+blacklist snd-mixer-oss
+blacklist snd-pcm-oss
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/reconstruct
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/reconstruct
@@ -0,0 +1,206 @@
+# Recreate any symlinks created since the orig.
+chmod +x 'Documentation/devicetree/bindings/media/xilinx/xlnx,v-dprxss.yaml'
+chmod +x 'arch/mips/pci/pcie-octeon.c'
+chmod +x 'arch/s390/tools/gcc-thunk-extern.sh'
+chmod +x 'debian/cloud-tools/hv_get_dhcp_info'
+chmod +x 'debian/cloud-tools/hv_get_dns_info'
+chmod +x 'debian/cloud-tools/hv_set_ifconfig'
+chmod +x 'debian/rules'
+chmod +x 'debian/scripts/config-check'
+chmod +x 'debian/scripts/control-create'
+chmod +x 'debian/scripts/dkms-build'
+chmod +x 'debian/scripts/dkms-build--nvidia-N'
+chmod +x 'debian/scripts/dkms-build-configure--zfs'
+chmod +x 'debian/scripts/file-downloader'
+chmod +x 'debian/scripts/link-headers'
+chmod +x 'debian/scripts/misc/annotations'
+chmod +x 'debian/scripts/misc/arch-has-odm-enabled.sh'
+chmod +x 'debian/scripts/misc/final-checks'
+chmod +x 'debian/scripts/misc/find-missing-sauce.sh'
+chmod +x 'debian/scripts/misc/fw-to-ihex.sh'
+chmod +x 'debian/scripts/misc/gen-auto-reconstruct'
+chmod +x 'debian/scripts/misc/git-ubuntu-log'
+chmod +x 'debian/scripts/misc/insert-changes'
+chmod +x 'debian/scripts/misc/insert-mainline-changes'
+chmod +x 'debian/scripts/misc/insert-ubuntu-changes'
+chmod +x 'debian/scripts/misc/kernelconfig'
+chmod +x 'debian/scripts/misc/migrate-annotations'
+chmod +x 'debian/scripts/misc/retag'
+chmod +x 'debian/scripts/misc/splitconfig.pl'
+chmod +x 'debian/scripts/misc/tristate.sh'
+chmod +x 'debian/scripts/misc/update-aufs.sh'
+chmod +x 'debian/scripts/module-inclusion'
+chmod +x 'debian/scripts/module-signature-check'
+chmod +x 'debian/scripts/retpoline-extract'
+chmod +x 'debian/scripts/retpoline-extract-one'
+chmod +x 'debian/scripts/sign-module'
+chmod +x 'debian/templates/extra.postinst.in'
+chmod +x 'debian/templates/extra.postrm.in'
+chmod +x 'debian/templates/headers.postinst.in'
+chmod +x 'debian/templates/image.postinst.in'
+chmod +x 'debian/templates/image.postrm.in'
+chmod +x 'debian/templates/image.preinst.in'
+chmod +x 'debian/templates/image.prerm.in'
+chmod +x 'debian/tests-build/check-aliases'
+chmod +x 'debian/tests/rebuild'
+chmod +x 'debian/tests/ubuntu-regression-suite'
+chmod +x 'drivers/gpu/drm/zocl/common/include/xrt_drv.h'
+chmod +x 'drivers/gpu/drm/zocl/common/include/xrt_xclbin.h'
+chmod +x 'drivers/watchdog/f71808e_wdt.c'
+chmod +x 'scripts/pahole-flags.sh'
+chmod +x 'scripts/pahole-version.sh'
+chmod +x 'snapcraft.yaml'
+chmod +x 'tools/testing/selftests/net/fib_nexthop_nongw.sh'
+chmod -x 'tools/testing/selftests/net/setup_loopback.sh'
+chmod +x 'tools/testing/selftests/netfilter/conntrack_vrf.sh'
+# Remove any files deleted from the orig.
+rm -f 'Documentation/devicetree/bindings/ata/ahci-ceva.txt'
+rm -f 'Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt'
+rm -f 'Documentation/devicetree/bindings/net/can/xilinx_can.txt'
+rm -f 'Documentation/devicetree/bindings/net/macb.txt'
+rm -f 'Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml'
+rm -f 'Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml'
+rm -f 'Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.txt'
+rm -f 'Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu.txt'
+rm -f 'Documentation/devicetree/bindings/usb/dwc3-xilinx.txt'
+rm -f 'Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt'
+rm -f 'Documentation/networking/decnet.rst'
+rm -f 'Documentation/virt/kvm/amd-memory-encryption.rst'
+rm -f 'Documentation/virt/kvm/cpuid.rst'
+rm -f 'Documentation/virt/kvm/halt-polling.rst'
+rm -f 'Documentation/virt/kvm/hypercalls.rst'
+rm -f 'Documentation/virt/kvm/mmu.rst'
+rm -f 'Documentation/virt/kvm/msr.rst'
+rm -f 'Documentation/virt/kvm/nested-vmx.rst'
+rm -f 'Documentation/virt/kvm/running-nested-guests.rst'
+rm -f 'Documentation/virt/kvm/s390-diag.rst'
+rm -f 'Documentation/virt/kvm/s390-pv-boot.rst'
+rm -f 'Documentation/virt/kvm/s390-pv.rst'
+rm -f 'Documentation/virt/kvm/timekeeping.rst'
+rm -f 'arch/alpha/include/asm/bugs.h'
+rm -f 'arch/arm/mach-pxa/include/mach/spitz.h'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/Makefile'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts'
+rm -f 'arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi'
+rm -f 'arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi'
+rm -f 'arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts'
+rm -f 'arch/hexagon/include/asm/timer-regs.h'
+rm -f 'arch/ia64/include/asm/bugs.h'
+rm -f 'arch/m68k/include/asm/bugs.h'
+rm -f 'arch/parisc/include/asm/bugs.h'
+rm -f 'arch/powerpc/include/asm/bugs.h'
+rm -f 'arch/powerpc/include/uapi/asm/bpf_perf_event.h'
+rm -f 'arch/sh/include/asm/bugs.h'
+rm -f 'arch/sparc/include/asm/bugs.h'
+rm -f 'arch/um/include/asm/bugs.h'
+rm -f 'arch/x86/mm/mem_encrypt.c'
+rm -f 'arch/xtensa/include/asm/bugs.h'
+rm -f 'crypto/blake2s_generic.c'
+rm -f 'crypto/memneq.c'
+rm -f 'drivers/acpi/fan.c'
+rm -f 'drivers/block/sx8.c'
+rm -f 'drivers/bus/mhi/core/Makefile'
+rm -f 'drivers/bus/mhi/core/boot.c'
+rm -f 'drivers/bus/mhi/core/debugfs.c'
+rm -f 'drivers/bus/mhi/core/init.c'
+rm -f 'drivers/bus/mhi/core/internal.h'
+rm -f 'drivers/bus/mhi/core/main.c'
+rm -f 'drivers/bus/mhi/core/pm.c'
+rm -f 'drivers/bus/mhi/pci_generic.c'
+rm -f 'drivers/counter/counter.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/Makefile'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/bw_fixed.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/calcs_logger.h'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/custom_float.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calc_auto.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calc_auto.h'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calc_math.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/calcs/dcn_calcs.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/dml/dcn2x/dcn2x.c'
+rm -f 'drivers/gpu/drm/amd/display/dc/dml/dcn2x/dcn2x.h'
+rm -f 'drivers/gpu/drm/amd/display/dc/dsc/qp_tables.h'
+rm -f 'drivers/gpu/drm/msm/hdmi/hdmi_connector.c'
+rm -f 'drivers/gpu/drm/vmwgfx/vmwgfx_thp.c'
+rm -f 'drivers/iio/adc/stx104.c'
+rm -f 'drivers/infiniband/hw/irdma/status.h'
+rm -f 'drivers/input/serio/i8042-x86ia64io.h'
+rm -f 'drivers/net/ethernet/hisilicon/hns3/hns3pf/Makefile'
+rm -f 'drivers/net/ethernet/hisilicon/hns3/hns3vf/Makefile'
+rm -f 'drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_gpio.c'
+rm -f 'drivers/net/vxlan.c'
+rm -f 'drivers/of/of_net.c'
+rm -f 'drivers/pinctrl/ralink/pinctrl-rt2880.c'
+rm -f 'drivers/pinctrl/ralink/pinmux.h'
+rm -f 'drivers/platform/x86/hp-wmi.c'
+rm -f 'drivers/platform/x86/hp_accel.c'
+rm -f 'drivers/platform/x86/i2c-multi-instantiate.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_clk_and_regulator.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_common.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_common.h'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_discrete.c'
+rm -f 'drivers/platform/x86/intel/int3472/intel_skl_int3472_tps68470.c'
+rm -f 'drivers/platform/x86/tc1100-wmi.c'
+rm -f 'drivers/staging/clocking-wizard/Kconfig'
+rm -f 'drivers/staging/clocking-wizard/Makefile'
+rm -f 'drivers/staging/clocking-wizard/TODO'
+rm -f 'drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c'
+rm -f 'drivers/staging/clocking-wizard/dt-binding.txt'
+rm -f 'drivers/staging/most/dim2/sysfs.c'
+rm -f 'drivers/uio/uio.c'
+rm -f 'drivers/usb/typec/tcpm/tcpci.h'
+rm -f 'fs/io-wq.c'
+rm -f 'fs/io-wq.h'
+rm -f 'fs/io_uring.c'
+rm -f 'include/asm-generic/bugs.h'
+rm -f 'include/linux/counter_enum.h'
+rm -f 'include/net/dn.h'
+rm -f 'include/net/dn_dev.h'
+rm -f 'include/net/dn_fib.h'
+rm -f 'include/net/dn_neigh.h'
+rm -f 'include/net/dn_nsp.h'
+rm -f 'include/net/dn_route.h'
+rm -f 'include/trace/events/random.h'
+rm -f 'include/trace/events/rdma.h'
+rm -f 'include/uapi/linux/dn.h'
+rm -f 'include/uapi/linux/netfilter_decnet.h'
+rm -f 'include/uapi/linux/nfsd/nfsfh.h'
+rm -f 'kernel/futex.c'
+rm -f 'net/decnet/Kconfig'
+rm -f 'net/decnet/Makefile'
+rm -f 'net/decnet/README'
+rm -f 'net/decnet/af_decnet.c'
+rm -f 'net/decnet/dn_dev.c'
+rm -f 'net/decnet/dn_fib.c'
+rm -f 'net/decnet/dn_neigh.c'
+rm -f 'net/decnet/dn_nsp_in.c'
+rm -f 'net/decnet/dn_nsp_out.c'
+rm -f 'net/decnet/dn_route.c'
+rm -f 'net/decnet/dn_rules.c'
+rm -f 'net/decnet/dn_table.c'
+rm -f 'net/decnet/dn_timer.c'
+rm -f 'net/decnet/netfilter/Kconfig'
+rm -f 'net/decnet/netfilter/Makefile'
+rm -f 'net/decnet/netfilter/dn_rtmsg.c'
+rm -f 'net/decnet/sysctl_net_decnet.c'
+rm -f 'net/qrtr/qrtr.c'
+rm -f 'net/sched/cls_rsvp.c'
+rm -f 'net/sched/cls_rsvp.h'
+rm -f 'net/sched/cls_rsvp6.c'
+rm -f 'net/sched/cls_tcindex.c'
+rm -f 'net/sched/sch_atm.c'
+rm -f 'net/sched/sch_cbq.c'
+rm -f 'net/sched/sch_dsmark.c'
+rm -f 'net/xfrm/xfrm_interface.c'
+rm -f 'tools/build/feature/test-libpython-version.c'
+rm -f 'tools/perf/arch/arm64/util/machine.c'
+rm -f 'tools/perf/arch/powerpc/util/machine.c'
+rm -f 'tools/perf/pmu-events/arch/powerpc/power10/floating_point.json'
+rm -f 'tools/perf/util/bpf_skel/bperf.h'
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/rules.d/arm64.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/rules.d/arm64.mk
@@ -0,0 +1,31 @@
+human_arch	= ARMv8
+build_arch	= arm64
+header_arch	= arm64
+defconfig	= defconfig
+flavours	= xilinx-zynqmp
+build_image	= Image.gz
+kernel_file	= arch/$(build_arch)/boot/Image.gz
+install_file	= vmlinuz
+no_dumpfile = true
+
+loader		= grub
+vdso		= vdso_install
+
+do_extras_package = false
+do_tools_usbip  = true
+do_tools_cpupower = true
+do_tools_perf   = true
+do_tools_perf_jvmti = true
+do_tools_bpftool = true
+do_tools_host = false
+
+do_dtbs		= true
+do_zfs		= false
+do_dkms_wireguard = false
+do_dkms_nvidia = false
+
+disable_d_i = true
+do_source_package = false
+do_common_headers_indep = false
+do_libc_dev_package = false
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/rules.d/hooks.mk
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/rules.d/hooks.mk
@@ -0,0 +1 @@
+do_enforce_all = true
--- linux-xilinx-zynqmp-5.15.0.orig/debian.zynqmp/tracking-bug
+++ linux-xilinx-zynqmp-5.15.0/debian.zynqmp/tracking-bug
@@ -0,0 +1 @@
+2110826 2025.05.19-1
--- linux-xilinx-zynqmp-5.15.0.orig/debian/canonical-certs.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/canonical-certs.pem
@@ -0,0 +1,371 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number:
+            47:77:26:6d:ae:6c:57:73:eb:80:e2:96:dd:26:93:ff:e9:f5:62:5d
+        Signature Algorithm: sha512WithRSAEncryption
+        Issuer: CN=Canonical Ltd. Live Patch Signing 2025 Kmod
+        Validity
+            Not Before: May 16 09:07:40 2025 GMT
+            Not After : May 16 09:07:40 2050 GMT
+        Subject: CN=Canonical Ltd. Live Patch Signing 2025 Kmod
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (4096 bit)
+                Modulus:
+                    00:b8:a9:03:47:2e:7b:c6:86:16:f4:b7:a8:4d:3b:
+                    05:f6:c4:75:35:e9:22:8a:4e:40:06:89:15:7f:ad:
+                    99:bb:e6:90:93:61:c8:16:cf:2e:00:1b:81:36:fd:
+cc:31:7b:97:79:8d:5e:d2:4d:d3:2f:ab:35:2d:74:
+                    48:98:b3:d9:75:f9:bb:e1:f2:3f:6b:6d:dc:e4:bb:
+ee:f5:aa:f7:8a:8c:7a:a8:0b:df:b1:f8:d6:04:13:
+                    27:e9:1a:aa:c2:4d:d2:35:3a:bc:06:d7:83:7f:e8:
+c4:1c:63:8b:3a:ff:0e:0b:89:6e:4f:5f:ea:ad:78:
+df:37:ab:f9:55:1d:fb:6e:29:a4:22:43:d1:9b:12:
+                    1e:b2:84:23:1b:d2:38:91:b8:a8:6c:1c:59:3c:ff:
+                    4c:a9:18:ce:d0:7f:1d:ef:04:cf:8a:e8:29:b2:4b:
+                    68:0d:92:32:bc:9c:5d:8f:0a:d1:dd:4d:25:ba:3a:
+                    8c:6a:48:5b:1e:9c:01:10:99:c1:a7:34:ee:68:ec:
+a1:d3:26:be:45:c8:b4:97:ac:8a:aa:7e:13:a6:e5:
+                    43:f1:1b:3f:a1:80:0a:d2:a9:e7:f2:77:ca:e1:f5:
+                    29:36:df:75:8a:7e:02:d6:17:aa:46:12:b9:51:f0:
+                    6b:ca:22:f8:05:de:d6:02:47:76:0c:88:f1:c6:90:
+                    44:99:58:71:c7:62:1e:2b:94:c5:2b:8e:dc:ca:7b:
+a7:bd:cd:38:8f:4e:73:6d:b0:9b:4e:7c:12:1f:5c:
+c5:62:d6:82:c6:d2:78:09:52:dc:d7:78:2e:23:d0:
+                    63:1f:7d:77:91:c8:3f:66:7a:20:8a:cf:70:09:0f:
+a2:c0:82:a5:42:d9:be:dc:5f:78:73:f7:fa:3c:70:
+                    47:7b:39:77:89:5a:6f:ef:83:09:c9:1b:21:53:89:
+                    7c:10:bf:99:9c:05:39:32:1e:84:3b:a5:84:7e:ef:
+                    08:6d:b0:b0:31:61:d6:1a:aa:dd:7a:d6:10:02:e6:
+                    72:02:e5:40:bf:07:b9:cd:61:d1:55:04:9a:cd:02:
+                    73:41:c1:df:20:30:12:97:ca:a1:83:1a:97:8a:92:
+                    1c:47:5c:0a:60:da:41:3b:e6:0e:2c:82:ce:45:65:
+                    81:ba:45:a1:66:cc:ef:ab:65:5c:e5:a8:0c:86:dd:
+fc:86:54:f3:37:7c:89:a9:0c:fa:3a:da:82:c9:90:
+                    99:1e:1d:66:44:de:d3:c5:d4:0b:da:15:f8:d8:d4:
+                    63:2b:4e:6f:24:e9:c2:d7:74:9c:29:91:9f:25:39:
+                    8d:77:15:8c:cb:8e:ad:e3:80:0a:ea:79:04:72:9d:
+                    51:01:18:ae:35:51:ef:95:79:38:c4:db:99:50:47:
+                    62:38:e9
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+CA:FALSE
+            X509v3 Key Usage:
+                Digital Signature
+            X509v3 Subject Key Identifier:
+D5:41:CE:F6:1D:C7:E7:93:B7:EB:7E:89:99:70:A2:EE:F0:B5:DC:8C
+            X509v3 Authority Key Identifier:
+D5:41:CE:F6:1D:C7:E7:93:B7:EB:7E:89:99:70:A2:EE:F0:B5:DC:8C
+            X509v3 Extended Key Usage:
+                Code Signing, 1.3.6.1.4.1.2312.16.1.2
+    Signature Algorithm: sha512WithRSAEncryption
+    Signature Value:
+        40:9d:5b:70:66:fe:9c:99:eb:ed:78:61:be:da:67:da:ac:80:
+a8:c2:78:91:f8:90:11:be:9f:6a:e7:bf:79:dc:11:0c:c7:83:
+e8:13:c4:1c:b6:fe:f0:e7:7d:1a:12:97:5d:19:56:9c:10:12:
+        1e:b9:19:88:30:95:c4:3b:2f:aa:91:6f:c1:9e:68:4a:f4:5c:
+ef:a1:51:b5:a3:9b:58:3f:e2:ae:5c:29:a6:c4:30:fd:65:0b:
+cc:8c:99:95:33:61:c6:07:fa:c3:bd:1a:57:80:e5:43:97:2e:
+f3:5c:d6:1e:b7:23:9f:58:10:19:24:46:9e:f8:fd:2c:8e:88:
+e7:ec:ef:15:4b:7a:6a:ce:b0:25:c0:01:c5:21:83:1a:d5:89:
+        0c:90:86:ad:d4:3e:6e:28:bf:6c:21:91:ff:b9:a9:ef:d4:ac:
+de:7c:67:c1:e4:ed:75:26:15:ff:5d:67:39:24:2d:15:57:21:
+        09:76:e5:85:f3:45:e8:bf:b1:c0:39:2b:83:34:1a:f5:3f:1f:
+ae:07:8c:82:1f:d4:dc:95:c0:4e:f3:7f:ac:db:8f:2c:db:a4:
+d4:2a:4c:8c:de:e6:5b:84:fc:df:a3:74:d8:dc:9c:93:1f:5b:
+c9:33:b5:b3:7d:2b:a4:4d:7a:bb:73:92:ff:8d:e9:9e:c7:a7:
+d2:0d:83:bb:2c:2f:47:51:15:5c:6d:db:9a:d3:9e:6e:25:90:
+        01:e6:09:bd:a2:d0:1e:cf:a3:12:22:0d:56:70:bf:89:e4:be:
+        62:76:9c:d9:f5:c8:01:55:95:02:57:a1:67:59:88:97:57:f6:
+bb:8d:c9:40:d5:e3:60:4f:43:dd:49:90:fa:a5:6d:08:96:b2:
+        4d:dd:a7:c6:e3:5c:06:ba:af:8c:30:9d:d5:a5:b0:ab:c4:e5:
+f3:09:47:05:ba:9b:46:f4:26:70:3b:fa:da:a5:0a:47:ce:be:
+        43:87:eb:73:63:3b:cd:41:7a:78:a0:f6:7d:c5:37:fb:bb:26:
+        3b:b3:e7:44:49:06:8c:14:03:fc:b3:46:54:3b:0d:57:02:08:
+        99:79:68:a2:9c:62:95:4d:ac:8e:19:43:4e:8f:2d:52:fa:91:
+ca:78:06:a2:b7:a3:66:6d:67:0b:13:ee:b1:01:38:e0:7c:ac:
+        9a:16:27:36:f1:45:83:5d:eb:d6:cd:65:3f:56:9a:d3:56:c4:
+        15:55:b2:64:ca:13:cb:31:1e:7e:03:85:68:61:40:02:99:4b:
+        25:01:68:8d:97:cc:39:1a:54:1b:e5:51:38:8e:ce:66:74:61:
+        5e:87:f4:31:7d:0d:be:9d:01:e1:b3:5c:bc:1a:d0:ea:5e:b2:
+c8:ee:97:34:bc:9f:bb:98
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number:
+            c7:7e:51:6a:1c:25:cd:40
+        Signature Algorithm: sha512WithRSAEncryption
+        Issuer: CN = Canonical Ltd. Live Patch Signing
+        Validity
+            Not Before: Jul 18 23:41:27 2016 GMT
+            Not After : Jul 16 23:41:27 2026 GMT
+        Subject: CN = Canonical Ltd. Live Patch Signing
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                RSA Public-Key: (4096 bit)
+                Modulus:
+                    00:bd:74:ee:72:b3:4a:ab:e6:31:e8:29:24:c2:bd:
+                    46:98:32:c0:39:ee:a3:fb:8a:ad:fe:ab:1a:5b:a3:
+                    2e:a1:80:db:79:61:9e:47:79:2c:75:57:a2:21:f0:
+                    93:f6:87:f2:9b:4b:9d:2f:b3:58:61:28:3c:41:70:
+                    13:16:a1:72:90:c9:d5:16:71:7c:e0:30:f9:28:5e:
+                    48:20:36:00:69:b7:59:9f:a3:ec:a8:eb:55:41:9f:
+                    38:1e:22:4a:57:20:f4:83:59:49:c5:00:93:d3:33:
+                    02:92:d1:fc:f0:84:3b:4a:5b:8f:b6:73:9a:89:fa:
+                    30:1e:e6:2a:68:f2:91:ef:59:57:3d:dc:1c:52:6f:
+                    5e:e6:9b:b5:b8:7c:98:c9:13:d1:39:68:01:67:91:
+                    e0:d3:67:72:16:0a:5e:16:83:45:31:4f:b5:2b:b3:
+                    f6:40:86:89:3a:84:6e:6f:16:61:bc:70:84:be:5a:
+                    13:36:7b:82:ea:07:19:fc:18:c1:16:c6:32:0b:7d:
+                    2c:6b:c4:21:b9:38:6b:31:dc:d9:0c:ad:56:40:68:
+                    7c:e3:c6:64:8e:bf:1c:e0:72:3e:6c:db:d2:73:79:
+                    da:d7:c5:2f:5d:04:7d:b0:07:1e:95:dd:2a:47:5e:
+                    bf:3e:3a:c8:66:f6:67:0f:d4:2a:f1:e2:71:59:d2:
+                    6c:7b:a0:37:ac:e6:97:80:30:13:97:48:d5:74:fc:
+                    38:68:e4:57:cb:99:69:5a:84:27:ac:98:51:e4:64:
+                    bd:91:62:e8:58:27:06:2a:b9:0b:b8:08:e5:e5:b4:
+                    51:a7:a2:10:df:4e:07:6c:a0:3b:96:f2:6e:df:75:
+                    8c:97:1e:64:a0:9a:86:9b:98:26:f9:d8:b7:de:5b:
+                    21:b7:af:89:01:a3:f7:98:6b:da:19:ba:86:ef:ef:
+                    f1:ce:bb:2f:89:ed:c0:b6:1b:e5:5b:f8:90:11:9a:
+                    52:93:e9:be:f7:35:b9:08:cb:ba:c3:ed:2f:73:af:
+                    cc:96:07:55:b5:de:f6:03:f6:f1:89:f9:21:40:76:
+                    c1:69:f2:61:cc:9a:94:df:9c:ec:6a:65:38:be:d1:
+                    4e:2a:87:c7:2f:3e:53:ae:8b:9f:54:a1:09:59:64:
+                    25:aa:a9:d8:44:a9:a8:a0:71:e1:32:aa:4c:32:fd:
+                    44:28:cc:9c:6f:8e:db:81:7e:6f:fa:00:56:c5:e5:
+                    03:46:63:fb:8e:71:8d:e3:13:91:9f:ac:60:3e:64:
+                    f3:df:25:34:09:fa:2d:96:9f:16:05:ea:93:f5:e6:
+                    00:08:27:32:7b:3c:bd:ee:70:24:6c:3b:55:e9:db:
+                    f4:10:2d:20:06:b4:ca:e9:29:65:55:ad:f6:52:54:
+                    5f:e5:a3
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Key Usage: 
+                Digital Signature
+            X509v3 Subject Key Identifier: 
+                14:DF:34:D1:A8:7C:F3:76:25:AB:EC:03:9E:F2:BF:52:12:49:B9:69
+            X509v3 Authority Key Identifier: 
+                keyid:14:DF:34:D1:A8:7C:F3:76:25:AB:EC:03:9E:F2:BF:52:12:49:B9:69
+
+    Signature Algorithm: sha512WithRSAEncryption
+         30:e7:48:02:37:e9:28:cf:04:a2:4d:5c:fa:d8:4e:c9:76:c7:
+         14:3f:bd:2c:51:3d:33:f0:1a:bc:49:f1:47:95:8f:69:d8:a9:
+         54:14:44:6c:4d:9f:55:82:08:1e:c6:5b:d5:91:d9:bc:2e:b0:
+         af:d6:25:65:74:96:aa:36:de:ae:31:a8:11:f2:a4:2c:5a:e1:
+         4f:73:f8:4a:c3:35:b0:76:96:71:f2:b5:7d:4b:75:ee:5d:bf:
+         86:a5:ba:0b:a9:52:cb:ec:ab:e5:23:4b:f2:74:55:28:17:1e:
+         b3:ac:27:ad:45:13:6e:69:b3:5a:be:42:36:29:48:db:e7:5c:
+         22:58:a0:90:82:2c:2a:21:2b:db:f4:64:b7:91:5d:1f:2c:48:
+         a4:1a:85:e3:86:a5:aa:19:cd:19:e8:a5:fb:a3:7b:94:77:48:
+         25:a4:cf:a0:cf:71:82:5c:6f:71:22:7c:d6:97:a0:53:bb:ec:
+         30:f6:cb:16:fb:7b:fd:16:94:7a:53:6e:bd:04:64:a2:01:10:
+         9f:f0:5b:b5:a6:73:41:9d:5f:6f:45:73:0d:05:f7:30:6d:39:
+         90:b6:7d:55:7d:4c:2f:ae:5f:38:56:2f:8b:df:f4:bf:12:06:
+         93:6e:0d:02:23:bf:71:91:57:88:e8:bd:62:72:99:00:40:29:
+         1e:c9:13:11:da:7e:8e:e1:d2:a5:0d:bf:f7:d6:ec:01:0d:89:
+         41:cd:d5:dc:d2:f7:5f:33:0d:4c:2f:85:b7:85:b7:81:e4:17:
+         29:f0:74:cf:0e:15:8c:1a:50:0b:08:63:1a:91:4f:e7:76:97:
+         f1:d4:3b:7e:72:d4:c5:45:58:0c:6a:e9:0d:f2:85:d8:91:1e:
+         37:bd:78:e3:39:4d:2e:fd:85:31:c1:a6:3b:6a:cc:2c:53:72:
+         1d:8e:7b:f0:e6:76:86:09:6f:1a:f3:e4:a1:e2:dd:76:5f:b0:
+         8c:e2:2a:54:5d:c1:88:49:90:10:15:42:7d:05:24:53:8c:54:
+         ff:48:18:1a:36:e3:31:d3:54:32:78:0d:fe:f2:3d:aa:0d:37:
+         15:84:b4:36:47:31:e8:85:6e:0b:58:38:ff:21:91:09:c9:a8:
+         43:a3:ea:60:cb:7e:ed:f7:41:6f:4e:91:c1:fd:77:46:e7:d4:
+         e7:86:c0:1b:fd:50:6c:aa:be:00:b3:63:02:ff:4e:c7:a5:57:
+         6e:29:64:e9:54:d5:30:63:38:5f:2d:5a:db:49:5f:14:14:22:
+         d2:81:1f:61:9e:ee:ee:16:66:d6:bc:bd:ac:1b:5c:fb:38:31:
+         95:33:2e:84:6e:7a:de:ee:b9:fc:97:17:06:13:bf:70:1c:6e:
+         76:ed:66:38:e2:70:08:00
+-----BEGIN CERTIFICATE-----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=
+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number:
+            e9:df:13:0f:92:92:a9:b7
+        Signature Algorithm: sha512WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Kernel Module Signing
+        Validity
+            Not Before: May 31 16:06:09 2016 GMT
+            Not After : May 29 16:06:09 2026 GMT
+        Subject: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Kernel Module Signing
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                RSA Public-Key: (4096 bit)
+                Modulus:
+                    00:b3:b0:4f:c6:0a:77:8b:f9:d1:53:33:34:d2:80:
+                    b5:63:6f:e1:f6:a2:83:99:d5:b6:b1:e4:99:91:fa:
+                    6c:19:c6:d0:91:2a:b9:7d:b5:98:a6:0d:28:01:b8:
+                    7c:8e:aa:38:ec:51:37:33:96:f0:b0:9b:8d:86:5f:
+                    67:23:69:2f:d7:c2:f3:fb:c5:d7:f9:04:ff:f2:e5:
+                    61:68:b7:29:b9:c6:8e:4b:4d:2d:8f:92:0c:00:b3:
+                    a3:d2:5a:08:64:cd:f2:09:0b:a5:0e:e6:64:75:d5:
+                    41:f4:4d:49:3a:0d:dc:b9:27:8e:c4:d6:b1:df:8f:
+                    6c:f0:e4:f7:31:cb:a9:04:a1:f9:a7:aa:15:da:59:
+                    03:4d:46:14:d0:dd:bf:e0:f5:9e:f0:71:0c:70:78:
+                    2b:08:fb:e0:b6:68:a4:74:12:9d:f7:f2:64:88:17:
+                    2a:8a:ed:1a:91:b5:6c:13:bd:4c:10:0a:0b:72:0b:
+                    90:db:7d:f3:78:44:4c:d2:a5:41:f7:1c:77:7d:5a:
+                    8a:54:bc:8f:fe:b7:ee:e1:bc:59:37:c4:d4:e8:14:
+                    d0:5b:42:9b:04:00:8e:6d:83:8a:25:21:5b:08:c4:
+                    7b:b2:d9:99:52:c9:5e:59:6d:c4:aa:52:59:e2:e4:
+                    2f:7e:7e:ac:05:01:99:bf:13:72:b7:45:c5:17:da:
+                    8a:d5:3e:71:73:2e:d8:aa:e6:eb:5a:d0:9a:c4:93:
+                    f3:be:eb:d2:47:25:34:16:29:fa:dd:9a:2f:b1:20:
+                    e5:41:4e:ed:ea:51:7c:23:80:ba:3d:b5:3a:0b:8c:
+                    9c:85:48:6c:3c:8b:29:2f:2f:12:c7:52:34:02:ea:
+                    0f:ac:53:23:3c:f8:3e:40:1b:30:63:e9:2d:e6:f6:
+                    58:cc:51:f9:eb:08:4a:b4:c7:16:80:d1:8b:c2:64:
+                    6a:71:a9:70:31:a4:a7:3a:c0:93:99:1b:0e:42:c1:
+                    00:6d:43:27:99:6c:e5:fd:23:16:c1:8e:b5:66:17:
+                    2b:4c:53:5a:6d:1e:96:16:13:6a:c6:d4:85:5b:74:
+                    2e:ce:7c:45:2f:ad:cb:75:9e:5e:91:bd:9a:6a:86:
+                    1a:06:bd:39:be:a3:50:56:ea:e1:f6:e3:95:69:d7:
+                    31:e4:66:f7:36:b5:51:c2:22:b4:9c:74:9c:44:0b:
+                    0e:16:5f:53:f0:23:c6:b9:40:bd:d6:b8:7d:1b:f6:
+                    73:f6:27:e7:c0:e3:65:a0:58:ab:5c:59:b7:80:8c:
+                    8c:04:b4:a9:ae:a0:51:40:10:3b:63:59:49:87:d1:
+                    9b:df:a3:8c:c4:2e:eb:70:c1:0a:18:1f:cb:22:c2:
+                    f2:4a:65:0d:e5:81:74:d8:ce:72:c6:35:be:ba:63:
+                    72:c4:f9
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Key Usage: 
+                Digital Signature
+            X509v3 Subject Key Identifier: 
+                88:F7:52:E5:60:A1:E0:73:7E:31:16:3A:46:6A:D7:B7:0A:85:0C:19
+            X509v3 Authority Key Identifier: 
+                keyid:88:F7:52:E5:60:A1:E0:73:7E:31:16:3A:46:6A:D7:B7:0A:85:0C:19
+
+    Signature Algorithm: sha512WithRSAEncryption
+         04:85:16:27:58:ba:71:28:57:86:7b:c2:83:db:e5:72:6f:1e:
+         b2:1c:63:b0:db:ad:c0:42:96:c0:4f:65:f6:35:4d:c0:07:0d:
+         46:be:d3:1e:ec:f1:22:18:2a:18:5d:bb:69:a6:a6:d4:0d:c3:
+         57:03:b9:e7:45:49:28:ca:6d:98:17:68:97:cb:7b:36:81:0a:
+         37:9e:34:79:f3:e1:0e:5b:77:43:bb:5a:a5:45:b7:16:50:86:
+         fd:12:a4:96:0f:15:19:09:1c:e1:fa:80:a5:80:09:be:bb:c8:
+         26:0b:3e:de:03:d2:c2:18:a4:8d:0d:de:c5:32:82:0b:fb:75:
+         55:66:1a:2a:bb:e4:bd:25:91:20:15:d4:be:b8:3f:53:e3:fb:
+         a8:c3:55:e3:d5:e7:82:18:95:df:39:09:a7:fc:89:6e:b4:1c:
+         aa:2d:e8:67:c2:0d:34:34:3e:f9:fa:0b:ce:81:92:11:ae:12:
+         0a:fe:35:63:ce:46:29:c4:2b:4f:cb:4e:05:0a:a1:11:e2:35:
+         f6:5a:5d:b5:e8:d2:6f:4c:fc:3d:24:a6:03:4b:dd:98:6b:f2:
+         71:58:16:1d:a5:25:ef:d9:06:7c:e8:db:7b:88:6a:89:5c:59:
+         01:92:64:db:44:08:63:6c:7c:32:d6:55:98:63:09:26:61:67:
+         0a:fe:5d:ee:fd:23:59:b3:4d:91:c1:4d:41:8b:cd:20:58:fa:
+         2d:45:e5:bd:1d:69:5c:03:a0:49:a6:97:54:13:b6:c9:e0:f8:
+         56:83:a1:2a:c3:f4:6c:fd:ab:20:ca:3d:9c:95:c0:cf:04:bb:
+         46:39:cf:34:81:65:45:27:64:01:7d:62:b3:b8:72:ea:10:d5:
+         0f:53:7d:39:88:25:09:6f:8c:bc:e0:49:bb:39:e2:0e:8d:cf:
+         56:4d:c1:82:6d:87:d2:e7:fc:c0:9f:a7:65:60:d2:6c:65:18:
+         59:38:6e:d0:9c:d7:c3:81:9a:9a:29:8f:83:84:c3:b5:44:ff:
+         28:ac:13:17:64:f2:26:13:d9:55:06:b7:69:68:7c:bf:ec:d1:
+         8c:ef:b7:da:76:e1:07:73:c6:31:62:31:cb:b6:e1:e7:7f:0c:
+         c3:f7:4c:52:be:25:36:8e:a1:bb:60:02:c3:cb:3e:6f:29:fc:
+         7f:6a:fa:f8:ec:0a:df:49:e2:57:0e:bc:bd:93:c3:1b:d5:36:
+         8a:ff:d8:1b:17:c7:1f:cb:69:00:d2:54:9e:ad:61:89:92:95:
+         11:f8:ea:17:83:9f:9b:09:7d:b8:94:a4:ea:f5:ae:ea:dc:dd:
+         62:b9:9e:68:9c:18:ec:19:c4:13:08:c8:b1:62:ab:8e:84:69:
+         11:3c:da:ea:0d:b7:22:bd
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/canonical-revoked-certs.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/canonical-revoked-certs.pem
@@ -0,0 +1,688 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 1 (0x1)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Apr 12 11:39:08 2012 GMT
+            Not After : Apr 11 11:39:08 2042 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:c9:5f:9b:62:8f:0b:b0:64:82:ac:be:c9:e2:62:
+                    e3:4b:d2:9f:1e:8a:d5:61:1a:2b:5d:38:f4:b7:ce:
+                    b9:9a:b8:43:b8:43:97:77:ab:4f:7f:0c:70:46:0b:
+                    fc:7f:6d:c6:6d:ea:80:5e:01:d2:b7:66:1e:87:de:
+                    0d:6d:d0:41:97:a8:a5:af:0c:63:4f:f7:7c:c2:52:
+                    cc:a0:31:a9:bb:89:5d:99:1e:46:6f:55:73:b9:76:
+                    69:ec:d7:c1:fc:21:d6:c6:07:e7:4f:bd:22:de:e4:
+                    a8:5b:2d:db:95:34:19:97:d6:28:4b:21:4c:ca:bb:
+                    1d:79:a6:17:7f:5a:f9:67:e6:5c:78:45:3d:10:6d:
+                    b0:17:59:26:11:c5:57:e3:7f:4e:82:ba:f6:2c:4e:
+                    c8:37:4d:ff:85:15:84:47:e0:ed:3b:7c:7f:bc:af:
+                    e9:01:05:a7:0c:6f:c3:e9:8d:a3:ce:be:a6:e3:cd:
+                    3c:b5:58:2c:9e:c2:03:1c:60:22:37:39:ff:41:02:
+                    c1:29:a4:65:51:ff:33:34:aa:42:15:f9:95:78:fc:
+                    2d:f5:da:8a:85:7c:82:9d:fb:37:2c:6b:a5:a8:df:
+                    7c:55:0b:80:2e:3c:b0:63:e1:cd:38:48:89:e8:14:
+                    06:0b:82:bc:fd:d4:07:68:1b:0f:3e:d9:15:dd:94:
+                    11:1b
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                61:48:2A:A2:83:0D:0A:B2:AD:5A:F1:0B:72:50:DA:90:33:DD:CE:F0
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        8f:8a:a1:06:1f:29:b7:0a:4a:d5:c5:fd:81:ab:25:ea:c0:7d:
+        e2:fc:6a:96:a0:79:93:67:ee:05:0e:25:12:25:e4:5a:f6:aa:
+        1a:f1:12:f3:05:8d:87:5e:f1:5a:5c:cb:8d:23:73:65:1d:15:
+        b9:de:22:6b:d6:49:67:c9:a3:c6:d7:62:4e:5c:b5:f9:03:83:
+        40:81:dc:87:9c:3c:3f:1c:0d:51:9f:94:65:0a:84:48:67:e4:
+        a2:f8:a6:4a:f0:e7:cd:cd:bd:94:e3:09:d2:5d:2d:16:1b:05:
+        15:0b:cb:44:b4:3e:61:42:22:c4:2a:5c:4e:c5:1d:a3:e2:e0:
+        52:b2:eb:f4:8b:2b:dc:38:39:5d:fb:88:a1:56:65:5f:2b:4f:
+        26:ff:06:78:10:12:eb:8c:5d:32:e3:c6:45:af:25:9b:a0:ff:
+        8e:ef:47:09:a3:e9:8b:37:92:92:69:76:7e:34:3b:92:05:67:
+        4e:b0:25:ed:bc:5e:5f:8f:b4:d6:ca:40:ff:e4:e2:31:23:0c:
+        85:25:ae:0c:55:01:ec:e5:47:5e:df:5b:bc:14:33:e3:c6:f5:
+        18:b6:d9:f7:dd:b3:b4:a1:31:d3:5a:5c:5d:7d:3e:bf:0a:e4:
+        e4:e8:b4:59:7d:3b:b4:8c:a3:1b:b5:20:a3:b9:3e:84:6f:8c:
+        21:00:c3:39
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 2 (0x2)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 26 21:52:11 2017 GMT
+            Not After : Sep 25 21:52:11 2047 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2017)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:ef:9f:fa:9f:19:3a:9d:38:23:91:cc:c4:f9:42:
+                    e0:f8:54:12:82:dc:97:2c:d6:5b:c1:35:eb:ff:4a:
+                    74:06:b5:9d:32:aa:7b:f3:fc:31:5a:34:3e:a1:a4:
+                    44:db:7b:6d:16:af:35:76:e0:9b:99:ad:21:11:c6:
+                    12:4b:ae:24:8f:bb:d3:b2:00:fe:c5:1d:9b:3a:1a:
+                    4a:6c:ca:fa:16:37:85:22:f9:ff:22:fc:40:e0:58:
+                    35:c1:39:27:b4:c6:42:1a:96:d8:a5:c5:95:2e:f7:
+                    c5:1e:21:6e:36:84:f7:a9:a1:e1:f1:03:08:96:65:
+                    71:f8:eb:83:cf:82:f7:9a:44:58:72:00:14:39:29:
+                    4b:e9:78:2f:65:20:b3:80:76:3b:ba:0d:2d:46:f6:
+                    37:05:e7:05:fe:bd:6c:c7:a2:65:b5:06:6e:07:24:
+                    99:a1:c1:cf:e1:0e:5e:49:41:71:17:a8:50:e7:38:
+                    99:e5:6e:b6:db:9f:63:db:56:f4:9c:7d:89:f6:d2:
+                    03:6c:99:83:e0:99:23:39:36:bd:cb:b5:26:7c:7d:
+                    b0:c6:fe:82:7c:52:ed:f9:2c:8f:79:71:3d:a9:2f:
+                    b5:aa:7e:77:a0:fd:69:f9:97:10:a8:b2:c6:7d:88:
+                    9e:a2:19:bd:31:b8:02:2d:34:4d:9d:98:60:82:ad:
+                    04:ff
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                24:2A:DE:75:AC:4A:15:E5:0D:50:C8:4B:0D:45:FF:3E:AE:70:7A:03
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        00:b2:b7:57:b5:2b:5d:16:d3:04:88:6a:d7:77:d5:0d:89:f1:
+        d2:6e:11:d1:8e:f5:62:05:c4:6a:57:df:eb:d2:86:68:f2:fd:
+        a7:37:11:3c:f4:ce:5d:fe:32:5f:31:a2:6b:3a:da:28:c2:88:
+        fa:7f:70:b5:25:99:ea:27:9a:56:6a:9d:b2:0f:14:99:e2:b7:
+        c6:39:1e:8e:a7:76:31:d9:ed:c5:05:8d:48:ae:1b:68:18:14:
+        51:a1:7d:f6:c7:df:cb:9d:eb:a4:3b:0b:ff:c2:07:c5:42:bc:
+        0d:b2:11:fa:37:17:2b:1c:b5:84:48:2d:f9:31:4a:57:49:8e:
+        61:a6:82:11:06:4c:34:ea:9c:2a:47:4d:eb:e0:26:af:da:d2:
+        c2:08:a0:37:35:7b:73:71:de:0b:c4:ba:c8:34:de:20:04:03:
+        6f:46:26:0d:b9:91:02:5b:71:76:cc:45:e4:08:d0:a6:dd:a4:
+        50:d3:d9:04:91:2b:d9:5c:34:88:fc:c2:37:fd:c6:d4:3e:57:
+        f7:6b:ba:7b:d7:02:7a:84:0c:c8:c1:19:cc:bc:fa:52:d5:7f:
+        b3:35:c4:53:5d:70:0a:f6:44:60:8d:a9:11:7a:1b:7d:ae:7b:
+        20:5a:4c:8d:44:f6:c1:a9:61:cb:dc:cb:90:37:d5:28:24:73:
+        87:d0:e0:d8
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 3 (0x3)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Oct 26 18:31:14 2018 GMT
+            Not After : Oct 24 18:31:14 2048 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (ESM 2018)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:bf:6a:e5:6d:55:7a:ec:7a:11:37:45:9c:4c:8f:
+                    6b:2d:56:d3:74:2b:32:ac:84:2d:ba:cb:cc:ec:8d:
+                    92:22:69:48:a5:d4:f6:75:11:66:2f:cb:b2:fd:9e:
+                    56:ab:e6:f1:52:8e:75:3e:50:bd:25:b3:50:fc:ef:
+                    3d:76:f3:3f:7f:03:f6:e2:a1:25:69:5c:14:98:54:
+                    bd:11:bf:e9:a5:ac:46:91:4b:1d:de:b7:18:2b:c8:
+                    22:83:15:a7:4a:00:8d:9d:e4:c0:da:f7:41:02:fd:
+                    9f:5f:79:93:56:cc:86:e1:b5:e0:39:0e:3c:a2:5b:
+                    fe:c0:56:f0:92:50:5a:2b:67:67:93:56:d7:7a:75:
+                    99:6a:25:b4:63:a8:5f:69:7e:3a:49:58:2a:a7:80:
+                    f6:5a:b4:be:b2:be:a8:8c:45:41:c9:f2:fc:76:a8:
+                    65:ef:99:29:0d:c9:9c:54:6b:0a:f0:4a:0e:61:0d:
+                    ed:99:32:af:12:e2:12:7b:9f:7b:ec:05:c4:e0:b6:
+                    d5:c3:71:28:ae:dd:0b:ba:97:ad:68:0b:76:e9:bf:
+                    e7:01:7e:64:54:39:23:85:36:c8:9d:dd:27:a1:ff:
+                    df:46:36:14:7e:cb:cc:a1:cd:49:0b:6d:c2:0c:45:
+                    99:56:58:7c:87:0d:59:9a:dc:4a:39:3b:1d:d9:15:
+                    2e:b5
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                36:51:88:C1:D3:74:D6:B0:7C:3C:8F:24:0F:8E:F7:22:43:3D:6A:8B
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        4c:0f:cd:77:60:b4:6f:53:87:f3:3c:4f:e6:81:5f:a7:1c:cc:
+        60:29:b6:34:6c:4d:08:9b:e2:d2:bd:f6:17:1a:62:79:b8:17:
+        bc:a2:60:59:fd:03:51:c3:b7:6b:de:73:b3:48:95:f5:0b:aa:
+        b6:3c:b4:34:dc:1d:0b:c4:97:62:87:e7:48:d5:8f:c9:ea:e8:
+        91:8f:2a:40:cd:b7:b3:ee:b2:98:9e:fb:37:31:29:e6:8e:2f:
+        0a:39:99:1e:c6:aa:b8:05:62:85:d3:a8:3e:60:38:98:0f:f0:
+        fe:c7:ab:01:a5:6a:a5:7f:70:a6:26:94:76:23:2f:08:89:74:
+        97:c2:2a:ca:22:3e:7a:ea:22:22:08:07:f4:bb:f6:bc:69:9c:
+        4e:44:33:e2:8e:70:17:b0:9b:cb:33:94:66:6d:ff:9a:7d:e9:
+        50:b2:e8:90:14:e4:2b:91:cb:a0:c5:2e:0e:cf:19:ef:44:ef:
+        84:f0:bd:57:9e:26:c2:63:3d:df:fc:a1:84:de:5c:d7:5f:3b:
+        fb:94:61:f0:93:89:1f:cf:c3:b2:d1:90:97:35:7d:b9:8a:ad:
+        e6:05:f0:e8:3b:a1:7c:af:2b:c4:af:18:33:2e:5e:87:db:9d:
+        80:b5:04:fd:00:d0:60:ab:ff:85:77:0f:cb:47:22:c9:b2:85:
+        a8:48:16:e2
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 4 (0x4)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 18 16:10:17 2019 GMT
+            Not After : Sep 16 16:10:17 2049 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2019)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:e6:47:d8:75:e5:87:59:26:87:83:7d:5b:7a:b8:
+                    58:3d:7c:ef:36:f8:a0:7a:b7:14:56:58:7d:01:f1:
+                    1c:3b:8c:e6:5b:03:77:7d:a0:ed:47:0a:45:e6:75:
+                    5c:de:95:38:0d:38:fa:41:79:89:56:31:87:e7:a3:
+                    9a:36:70:b6:cf:24:2f:99:26:89:08:39:0e:14:c3:
+                    35:be:02:8b:52:e1:8e:7b:0c:a6:9d:78:ff:01:60:
+                    d7:f5:c3:d5:f0:5e:dc:e4:23:09:59:72:93:d3:b5:
+                    22:af:7c:cd:e0:84:0f:af:11:2d:bc:c6:72:42:af:
+                    ea:67:63:c4:10:41:78:02:80:62:0d:43:74:b4:1c:
+                    ed:50:d7:94:f1:b0:bb:f9:57:80:e4:69:0f:83:4b:
+                    a2:e6:2c:4a:9a:e1:7d:7c:62:19:29:27:97:1f:4c:
+                    f1:85:f0:39:f5:31:9f:3a:39:0e:d4:4d:07:3a:40:
+                    55:4b:a6:6c:9d:04:89:51:2d:7c:b0:ef:40:b5:42:
+                    29:16:cc:65:73:38:62:21:f6:e3:2c:17:50:9d:74:
+                    34:4e:df:7c:4a:33:a4:bb:40:cf:d5:e5:ed:05:07:
+                    cd:4c:f9:af:7f:a6:5c:b9:f7:c5:16:45:4e:44:40:
+                    d7:85:32:de:ac:e5:75:ad:9b:d7:c0:26:33:1f:77:
+                    a5:37
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                C0:74:6F:D6:C5:DA:3A:E8:27:86:46:51:AD:66:AE:47:FE:24:B3:E8
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        aa:12:6c:d1:9d:6a:da:f0:ec:7c:17:46:3b:57:b8:d6:76:5f:
+        24:e6:06:a2:0a:55:1f:2f:d3:5e:8f:de:cf:02:f2:ff:e0:dd:
+        d3:c7:bd:75:59:aa:cd:34:f3:28:80:73:cc:28:69:e7:a2:70:
+        88:a2:c7:dc:66:f0:92:0e:ff:64:bf:30:04:54:01:1b:96:ad:
+        15:c5:61:fd:32:61:d7:5e:b5:ba:91:fd:31:fc:6b:15:df:ee:
+        22:d9:e4:1f:f3:cc:8b:0c:9f:f5:e8:f7:e2:62:3f:40:52:c9:
+        f0:f1:1c:63:fc:6c:90:e1:5b:74:03:b9:df:d1:3e:a8:ec:db:
+        2b:6e:83:6f:9f:7f:ba:b4:79:fc:3d:e7:12:2f:4a:e7:17:8c:
+        2b:77:a5:90:74:3c:bd:cf:75:83:0d:1a:95:d5:56:ef:07:9b:
+        a6:b3:31:e3:8c:97:ce:68:11:b5:7b:25:03:72:1c:ea:67:e9:
+        7c:3e:73:c7:7c:3e:fc:f5:ae:8a:b2:07:0d:15:6a:66:09:d7:
+        23:b9:5d:80:7a:26:d6:b6:22:30:aa:84:af:c0:42:e9:75:c3:
+        59:ab:a3:84:87:6b:0c:b7:ab:4e:92:69:ae:2c:82:6f:ab:01:
+        24:ab:ff:78:6d:59:85:c2:3b:23:c0:bd:0d:d8:6e:3a:29:82:
+        e1:c4:5f:db
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 6 (0x6)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 23 19:29:32 2021 GMT
+            Not After : Sep 22 19:29:32 2051 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v1)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:aa:b8:34:5b:b6:ae:44:bf:41:e1:78:11:b9:7a:
+                    c8:88:b3:b0:26:50:10:9c:98:d1:f3:98:9f:23:50:
+                    64:f6:39:dd:50:3a:23:44:53:65:fc:f3:9f:f5:a5:
+                    8b:ae:8b:df:47:9f:e9:d5:a0:92:19:f1:21:ea:cc:
+                    59:3a:74:df:45:71:bc:de:64:15:a5:f6:db:ca:71:
+                    fa:19:d4:44:0d:12:ec:47:3a:43:e2:f2:dd:8b:fe:
+                    0d:7b:dc:4d:db:53:06:22:61:e5:8b:35:49:b6:33:
+                    c4:0a:69:5f:5b:81:09:84:6b:42:33:18:09:9d:a0:
+                    35:f7:9c:1e:de:6e:de:90:69:1a:e8:32:e4:49:ad:
+                    c3:31:e9:f8:4a:a2:28:1d:db:0d:29:b6:48:0a:44:
+                    93:86:41:62:8f:73:97:60:10:8a:74:46:66:55:fe:
+                    a0:95:35:9e:ef:9f:af:11:fa:5b:a3:7c:c2:35:64:
+                    11:67:28:1e:14:0a:7d:68:61:9c:cd:c7:46:39:30:
+                    31:79:94:56:b3:45:16:9a:b5:77:66:fe:41:43:0f:
+                    00:48:6e:99:dd:0c:d4:47:2c:86:8c:50:04:61:20:
+                    dd:aa:8e:73:4f:21:b4:ee:09:4d:d3:40:01:d0:f2:
+                    a7:5b:7d:05:3d:c1:e7:65:26:aa:8c:9a:58:5a:7c:
+                    6d:6f
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                A8:D5:4B:BB:38:25:CF:B9:4F:A1:3C:9F:8A:59:4A:19:5C:10:7B:8D
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        24:25:25:7e:01:a5:c8:3d:54:8c:1b:05:73:d1:06:d8:db:d4:
+        3a:71:d5:19:9d:97:1c:85:3c:ca:38:5a:0c:25:25:39:1a:67:
+        bc:6c:9d:98:6c:f3:7d:5f:b7:40:f9:73:a0:f5:7b:40:a8:66:
+        a5:f1:53:b1:78:80:24:3f:19:50:2f:02:09:ec:a1:8a:e6:0d:
+        df:c4:ae:24:9e:69:0d:5c:dc:44:4c:38:3a:53:4e:4b:a1:4b:
+        92:9f:43:a4:9d:1e:76:33:18:1b:bf:62:e5:f5:bc:93:3c:4e:
+        21:d5:5b:20:69:11:28:c1:c5:93:b5:8e:96:1d:1b:ca:72:79:
+        24:de:67:2a:50:9d:ce:8b:41:dd:3e:82:dd:a5:04:75:54:fb:
+        35:70:98:87:b4:f3:ea:41:23:23:80:0e:99:d7:03:16:ee:7e:
+        11:e2:c8:29:ab:73:c5:6d:5c:a8:2f:32:03:9f:8e:66:d6:cb:
+        54:84:55:75:ab:9a:dd:95:fd:05:1e:11:85:37:1e:63:d2:f4:
+        7f:34:64:32:a1:63:91:91:50:39:14:1a:ea:54:78:e6:0d:04:
+        23:c7:83:51:c5:25:27:07:6c:f8:65:b7:da:95:89:76:83:cc:
+        f3:7e:06:74:d3:6c:ef:e9:17:de:29:1e:ab:5c:d7:ec:df:f1:
+        98:b8:e9:66
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 7 (0x7)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 23 19:29:42 2021 GMT
+            Not After : Sep 22 19:29:42 2051 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v2)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:ba:06:8b:ee:58:b7:8b:49:7b:53:7a:d1:df:02:
+                    e3:f2:d8:b0:8c:03:5c:f4:2d:0b:d8:18:3b:23:fa:
+                    68:b0:e8:e9:9d:dc:a2:eb:5e:d3:06:a9:28:d4:9f:
+                    14:b6:1e:1c:1d:ef:69:0e:7f:44:f2:cc:4a:f1:b1:
+                    d0:71:30:6a:50:1e:b0:d3:f8:a4:19:d0:4a:f1:e3:
+                    eb:7a:e5:57:4c:a1:fb:d1:87:b9:48:e0:55:37:52:
+                    f9:de:99:2e:95:85:36:ce:d3:1d:67:2f:14:cb:7f:
+                    05:82:75:21:b6:aa:a5:14:ac:da:4a:f4:fe:fa:5c:
+                    33:49:3d:6f:de:fd:9d:75:ba:e2:c4:02:38:b5:69:
+                    f5:ff:a8:67:4b:3a:e0:34:f6:3b:07:03:a5:7e:59:
+                    6f:3a:d2:28:a4:2f:25:ac:d8:a9:1f:59:52:5d:24:
+                    36:58:51:b5:f0:12:a8:d3:78:56:57:b1:e0:a9:df:
+                    14:05:65:7c:b5:a5:00:f0:88:39:14:44:18:85:2d:
+                    0c:28:69:7b:b9:b4:1c:47:6f:43:66:4c:22:ad:f7:
+                    f6:19:75:e1:14:2c:0d:33:3f:c1:3f:fc:73:56:b2:
+                    68:05:b5:92:03:9b:65:6b:81:80:92:35:03:9b:66:
+                    68:58:c5:66:11:b6:8c:7f:05:09:9a:45:a6:0e:5e:
+                    5f:bf
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                4C:F0:46:89:2D:6F:D3:C9:A5:B0:3F:98:D8:45:F9:08:51:DC:6A:8C
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        93:9d:49:7d:9f:3e:3e:27:79:97:d9:c2:fc:0b:f7:30:b7:f4:
+        78:b2:c9:e4:5e:42:d3:27:26:70:cf:88:96:d1:f2:ea:a0:75:
+        7e:3c:f6:b7:d2:e7:95:30:e3:a6:67:a7:ee:b9:53:8f:fd:b2:
+        cb:db:e1:98:32:be:98:79:09:46:c6:63:6a:57:87:4d:b2:26:
+        46:f6:34:5e:18:75:ca:82:80:8e:33:c2:1d:c7:76:d7:14:57:
+        ef:2e:0e:9e:58:5c:81:8e:ed:53:2c:07:46:0a:8a:fc:2f:f5:
+        b2:c8:58:f5:fa:fa:bb:f9:7d:47:13:39:f0:f2:1c:15:9c:75:
+        90:40:bd:08:04:b3:6a:de:c2:cd:34:21:7e:ba:31:48:bc:a1:
+        23:bc:ee:93:b2:62:96:27:30:86:c2:d4:f7:b4:e6:3c:71:47:
+        37:84:ff:3d:0c:1e:ec:f3:0e:da:6b:dc:64:7a:b8:c0:7e:45:
+        13:09:bf:02:b3:b7:5b:6d:09:2d:6a:4e:0b:93:94:29:4c:a6:
+        c3:c7:05:fa:69:08:04:53:3c:4c:64:c0:7e:89:00:91:1b:a6:
+        c2:d7:ea:c4:db:86:38:fe:66:03:85:7b:fc:39:24:99:4c:2a:
+        3e:10:8b:91:c3:6e:20:9d:0c:ee:51:70:b5:98:58:f3:5c:ac:
+        16:98:7b:ce
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 8 (0x8)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 23 19:30:02 2021 GMT
+            Not After : Sep 22 19:30:02 2051 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v3)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:d6:29:96:87:ae:07:42:45:bb:65:09:b2:9b:de:
+                    5d:8e:78:61:10:d5:6d:ae:ae:26:08:6a:06:ec:4a:
+                    dd:2b:e7:1a:a9:ad:78:e3:fc:cf:8f:d1:47:bd:1e:
+                    33:d8:7a:e3:66:9b:e9:73:c1:5f:42:e2:fe:bc:c3:
+                    41:f7:cd:d7:85:d7:42:c9:ea:31:e5:47:b1:93:5b:
+                    43:2b:07:51:b8:75:08:ad:0f:e7:0d:81:38:5a:21:
+                    df:b1:43:5b:db:37:c5:ac:aa:14:3a:33:19:6a:26:
+                    e0:05:fe:cd:41:31:af:5d:a8:ab:31:77:44:fc:da:
+                    00:e2:7a:44:33:c3:a7:ed:13:54:9f:19:5d:c9:98:
+                    a2:3b:af:4d:0d:87:29:9c:90:9e:42:9e:9a:06:6a:
+                    70:27:c5:aa:f7:a2:f2:88:e0:b9:66:9a:72:a0:f6:
+                    61:7e:30:8f:14:9f:44:0d:dd:54:ae:47:c8:82:ba:
+                    d2:b2:db:6f:24:c1:f4:0a:81:07:90:47:49:5f:57:
+                    d6:3f:bf:2a:73:98:f2:f6:24:1a:74:03:d7:35:f0:
+                    42:d8:14:c5:94:27:5d:3c:49:0c:b0:f0:7a:61:1b:
+                    d7:5a:e3:a3:40:57:e9:a4:07:ee:02:a3:32:27:94:
+                    bb:f3:36:c5:5f:ef:d3:07:04:3a:80:4c:9c:0a:b7:
+                    88:9f
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                10:04:37:BB:6D:E6:E4:69:B5:81:E6:1C:D6:6B:CE:3E:F4:ED:53:AF
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        3b:37:d6:a8:8d:cd:d2:df:13:35:ac:8c:92:d6:b0:ac:d1:38:
+        a8:00:97:47:59:b8:4a:84:8c:80:a5:1d:c7:29:bf:00:66:e5:
+        10:40:26:2e:31:f5:e1:13:c0:1b:29:f3:0b:7e:2d:71:d8:db:
+        e1:32:8f:79:8e:e3:97:0c:40:a9:a0:12:c1:fc:c2:50:88:72:
+        44:c5:bc:8b:45:6e:28:fd:d2:37:d6:db:17:cf:4e:61:33:08:
+        5a:5d:08:94:73:44:e2:76:00:44:1b:b8:00:a1:86:00:64:8a:
+        f1:42:32:3c:28:11:67:7c:8b:aa:06:34:74:58:e8:b3:3a:36:
+        8d:f6:04:5d:37:f5:66:52:c9:48:b0:a7:6f:34:09:dd:60:2a:
+        86:b9:14:f1:09:f6:06:16:56:e0:51:b1:e8:75:7f:fa:37:dc:
+        e0:98:a7:69:ae:7b:1a:73:89:0d:06:67:cc:01:ef:80:31:45:
+        9e:bb:03:2a:eb:89:70:d6:19:b2:c7:ce:bc:81:df:da:c8:6f:
+        a9:4b:2d:d7:a7:e1:af:c6:e8:fb:f0:61:c9:cd:d2:91:cd:8b:
+        c2:6c:ef:e0:b6:7f:f1:c4:81:f9:bb:76:9c:26:e3:fa:a1:a0:
+        cd:5e:05:de:ee:f9:1b:5b:50:0a:8b:0f:47:e3:90:32:ac:2a:
+        e7:65:02:80
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 3 (0x3)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Mar  4 10:27:14 2020 GMT
+            Not After : Mar  3 10:27:14 2050 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (Ubuntu Core 2019)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:b9:10:47:2e:75:5d:f3:10:23:bb:a0:75:d2:fa:
+                    02:2d:ff:22:df:c1:e6:cd:38:7c:36:0f:ae:74:15:
+                    6e:a5:34:52:2b:c3:a4:3a:60:d7:06:ee:1d:99:93:
+                    ff:66:91:a3:18:52:2c:8c:58:e6:b4:2f:4b:c5:fb:
+                    83:e6:f3:19:bd:1b:ca:23:ec:97:1f:d8:f1:9a:f1:
+                    04:da:da:10:04:53:4b:ec:1d:b6:26:47:7c:bb:8f:
+                    a7:0a:6e:2e:e8:91:e6:c4:bb:64:34:78:3c:fa:09:
+                    15:1c:8f:9e:eb:04:99:36:22:c6:8d:07:15:0f:b9:
+                    69:08:fa:ff:4b:45:bd:ba:2b:cd:01:0e:e7:01:23:
+                    c9:e5:7a:39:3b:91:b0:45:3c:d5:77:ba:ca:f9:29:
+                    3d:11:3f:1c:6b:5b:8e:6c:4b:3f:c9:29:05:cb:59:
+                    d6:b1:c1:c0:2d:56:88:70:27:fa:73:05:5c:c2:11:
+                    d4:27:11:f7:0b:c2:d5:68:d3:1a:cd:ed:d0:e4:10:
+                    ff:34:cb:b7:45:70:34:2c:23:53:b6:9c:30:70:b4:
+                    5c:d1:e2:64:18:82:8f:62:b1:5e:aa:0b:d4:89:f2:
+                    1c:53:c4:32:7d:ef:53:ee:9b:6e:02:ab:78:bd:25:
+                    67:8b:39:36:d8:84:3b:06:99:02:d6:75:73:4e:f2:
+                    f6:b9
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                C1:D5:7B:8F:6B:74:3F:23:EE:41:F4:F7:EE:29:2F:06:EE:CA:DF:B9
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        2d:b5:11:a8:d2:a0:af:81:a0:18:22:18:2c:08:d0:f4:63:e8:
+        8f:9a:f4:f5:20:dd:eb:22:77:19:9a:1a:09:3d:7f:aa:7d:c9:
+        81:bc:26:98:65:94:46:30:4b:c2:51:7c:f7:21:41:63:87:31:
+        fc:a4:c9:41:28:c7:2e:2a:2e:d8:a8:75:7a:72:77:3b:1b:9f:
+        72:15:0d:0c:96:8d:8b:51:f3:ce:37:b6:ca:9f:ca:59:40:4a:
+        fc:73:7a:94:12:99:aa:c2:8d:52:ce:91:19:2e:b4:da:ff:e5:
+        2c:67:74:d9:58:47:38:2f:61:88:c5:cf:a7:48:e1:08:ba:bc:
+        ec:d5:3a:47:d9:8c:dc:c3:bc:cb:98:2b:79:7a:02:46:ef:85:
+        19:2f:03:4b:05:84:eb:56:98:5f:6d:cf:a5:8b:a2:b6:e5:50:
+        51:7c:33:44:bd:7a:94:2e:0d:90:39:39:3e:62:60:ae:3a:e2:
+        f5:17:fa:f1:94:06:1d:ae:a3:f8:19:20:7f:4b:4c:07:c4:e6:
+        2d:0d:e5:94:84:51:6d:6f:0f:c4:c6:79:1d:f0:e8:0e:23:9e:
+        fd:f9:46:2c:b9:ec:97:38:56:7e:b8:13:f6:d2:e1:8e:a5:93:
+        02:7b:6e:dd:33:9a:bf:10:a8:1b:3d:fa:c4:f2:15:f0:27:73:
+        26:a6:94:d1
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/certs/canonical-livepatch-2025-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/certs/canonical-livepatch-2025-all.pem
@@ -0,0 +1,125 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number:
+            47:77:26:6d:ae:6c:57:73:eb:80:e2:96:dd:26:93:ff:e9:f5:62:5d
+        Signature Algorithm: sha512WithRSAEncryption
+        Issuer: CN=Canonical Ltd. Live Patch Signing 2025 Kmod
+        Validity
+            Not Before: May 16 09:07:40 2025 GMT
+            Not After : May 16 09:07:40 2050 GMT
+        Subject: CN=Canonical Ltd. Live Patch Signing 2025 Kmod
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (4096 bit)
+                Modulus:
+                    00:b8:a9:03:47:2e:7b:c6:86:16:f4:b7:a8:4d:3b:
+                    05:f6:c4:75:35:e9:22:8a:4e:40:06:89:15:7f:ad:
+                    99:bb:e6:90:93:61:c8:16:cf:2e:00:1b:81:36:fd:
+cc:31:7b:97:79:8d:5e:d2:4d:d3:2f:ab:35:2d:74:
+                    48:98:b3:d9:75:f9:bb:e1:f2:3f:6b:6d:dc:e4:bb:
+ee:f5:aa:f7:8a:8c:7a:a8:0b:df:b1:f8:d6:04:13:
+                    27:e9:1a:aa:c2:4d:d2:35:3a:bc:06:d7:83:7f:e8:
+c4:1c:63:8b:3a:ff:0e:0b:89:6e:4f:5f:ea:ad:78:
+df:37:ab:f9:55:1d:fb:6e:29:a4:22:43:d1:9b:12:
+                    1e:b2:84:23:1b:d2:38:91:b8:a8:6c:1c:59:3c:ff:
+                    4c:a9:18:ce:d0:7f:1d:ef:04:cf:8a:e8:29:b2:4b:
+                    68:0d:92:32:bc:9c:5d:8f:0a:d1:dd:4d:25:ba:3a:
+                    8c:6a:48:5b:1e:9c:01:10:99:c1:a7:34:ee:68:ec:
+a1:d3:26:be:45:c8:b4:97:ac:8a:aa:7e:13:a6:e5:
+                    43:f1:1b:3f:a1:80:0a:d2:a9:e7:f2:77:ca:e1:f5:
+                    29:36:df:75:8a:7e:02:d6:17:aa:46:12:b9:51:f0:
+                    6b:ca:22:f8:05:de:d6:02:47:76:0c:88:f1:c6:90:
+                    44:99:58:71:c7:62:1e:2b:94:c5:2b:8e:dc:ca:7b:
+a7:bd:cd:38:8f:4e:73:6d:b0:9b:4e:7c:12:1f:5c:
+c5:62:d6:82:c6:d2:78:09:52:dc:d7:78:2e:23:d0:
+                    63:1f:7d:77:91:c8:3f:66:7a:20:8a:cf:70:09:0f:
+a2:c0:82:a5:42:d9:be:dc:5f:78:73:f7:fa:3c:70:
+                    47:7b:39:77:89:5a:6f:ef:83:09:c9:1b:21:53:89:
+                    7c:10:bf:99:9c:05:39:32:1e:84:3b:a5:84:7e:ef:
+                    08:6d:b0:b0:31:61:d6:1a:aa:dd:7a:d6:10:02:e6:
+                    72:02:e5:40:bf:07:b9:cd:61:d1:55:04:9a:cd:02:
+                    73:41:c1:df:20:30:12:97:ca:a1:83:1a:97:8a:92:
+                    1c:47:5c:0a:60:da:41:3b:e6:0e:2c:82:ce:45:65:
+                    81:ba:45:a1:66:cc:ef:ab:65:5c:e5:a8:0c:86:dd:
+fc:86:54:f3:37:7c:89:a9:0c:fa:3a:da:82:c9:90:
+                    99:1e:1d:66:44:de:d3:c5:d4:0b:da:15:f8:d8:d4:
+                    63:2b:4e:6f:24:e9:c2:d7:74:9c:29:91:9f:25:39:
+                    8d:77:15:8c:cb:8e:ad:e3:80:0a:ea:79:04:72:9d:
+                    51:01:18:ae:35:51:ef:95:79:38:c4:db:99:50:47:
+                    62:38:e9
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+CA:FALSE
+            X509v3 Key Usage:
+                Digital Signature
+            X509v3 Subject Key Identifier:
+D5:41:CE:F6:1D:C7:E7:93:B7:EB:7E:89:99:70:A2:EE:F0:B5:DC:8C
+            X509v3 Authority Key Identifier:
+D5:41:CE:F6:1D:C7:E7:93:B7:EB:7E:89:99:70:A2:EE:F0:B5:DC:8C
+            X509v3 Extended Key Usage:
+                Code Signing, 1.3.6.1.4.1.2312.16.1.2
+    Signature Algorithm: sha512WithRSAEncryption
+    Signature Value:
+        40:9d:5b:70:66:fe:9c:99:eb:ed:78:61:be:da:67:da:ac:80:
+a8:c2:78:91:f8:90:11:be:9f:6a:e7:bf:79:dc:11:0c:c7:83:
+e8:13:c4:1c:b6:fe:f0:e7:7d:1a:12:97:5d:19:56:9c:10:12:
+        1e:b9:19:88:30:95:c4:3b:2f:aa:91:6f:c1:9e:68:4a:f4:5c:
+ef:a1:51:b5:a3:9b:58:3f:e2:ae:5c:29:a6:c4:30:fd:65:0b:
+cc:8c:99:95:33:61:c6:07:fa:c3:bd:1a:57:80:e5:43:97:2e:
+f3:5c:d6:1e:b7:23:9f:58:10:19:24:46:9e:f8:fd:2c:8e:88:
+e7:ec:ef:15:4b:7a:6a:ce:b0:25:c0:01:c5:21:83:1a:d5:89:
+        0c:90:86:ad:d4:3e:6e:28:bf:6c:21:91:ff:b9:a9:ef:d4:ac:
+de:7c:67:c1:e4:ed:75:26:15:ff:5d:67:39:24:2d:15:57:21:
+        09:76:e5:85:f3:45:e8:bf:b1:c0:39:2b:83:34:1a:f5:3f:1f:
+ae:07:8c:82:1f:d4:dc:95:c0:4e:f3:7f:ac:db:8f:2c:db:a4:
+d4:2a:4c:8c:de:e6:5b:84:fc:df:a3:74:d8:dc:9c:93:1f:5b:
+c9:33:b5:b3:7d:2b:a4:4d:7a:bb:73:92:ff:8d:e9:9e:c7:a7:
+d2:0d:83:bb:2c:2f:47:51:15:5c:6d:db:9a:d3:9e:6e:25:90:
+        01:e6:09:bd:a2:d0:1e:cf:a3:12:22:0d:56:70:bf:89:e4:be:
+        62:76:9c:d9:f5:c8:01:55:95:02:57:a1:67:59:88:97:57:f6:
+bb:8d:c9:40:d5:e3:60:4f:43:dd:49:90:fa:a5:6d:08:96:b2:
+        4d:dd:a7:c6:e3:5c:06:ba:af:8c:30:9d:d5:a5:b0:ab:c4:e5:
+f3:09:47:05:ba:9b:46:f4:26:70:3b:fa:da:a5:0a:47:ce:be:
+        43:87:eb:73:63:3b:cd:41:7a:78:a0:f6:7d:c5:37:fb:bb:26:
+        3b:b3:e7:44:49:06:8c:14:03:fc:b3:46:54:3b:0d:57:02:08:
+        99:79:68:a2:9c:62:95:4d:ac:8e:19:43:4e:8f:2d:52:fa:91:
+ca:78:06:a2:b7:a3:66:6d:67:0b:13:ee:b1:01:38:e0:7c:ac:
+        9a:16:27:36:f1:45:83:5d:eb:d6:cd:65:3f:56:9a:d3:56:c4:
+        15:55:b2:64:ca:13:cb:31:1e:7e:03:85:68:61:40:02:99:4b:
+        25:01:68:8d:97:cc:39:1a:54:1b:e5:51:38:8e:ce:66:74:61:
+        5e:87:f4:31:7d:0d:be:9d:01:e1:b3:5c:bc:1a:d0:ea:5e:b2:
+c8:ee:97:34:bc:9f:bb:98
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/certs/canonical-livepatch-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/certs/canonical-livepatch-all.pem
@@ -0,0 +1,121 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number:
+            c7:7e:51:6a:1c:25:cd:40
+        Signature Algorithm: sha512WithRSAEncryption
+        Issuer: CN = Canonical Ltd. Live Patch Signing
+        Validity
+            Not Before: Jul 18 23:41:27 2016 GMT
+            Not After : Jul 16 23:41:27 2026 GMT
+        Subject: CN = Canonical Ltd. Live Patch Signing
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                RSA Public-Key: (4096 bit)
+                Modulus:
+                    00:bd:74:ee:72:b3:4a:ab:e6:31:e8:29:24:c2:bd:
+                    46:98:32:c0:39:ee:a3:fb:8a:ad:fe:ab:1a:5b:a3:
+                    2e:a1:80:db:79:61:9e:47:79:2c:75:57:a2:21:f0:
+                    93:f6:87:f2:9b:4b:9d:2f:b3:58:61:28:3c:41:70:
+                    13:16:a1:72:90:c9:d5:16:71:7c:e0:30:f9:28:5e:
+                    48:20:36:00:69:b7:59:9f:a3:ec:a8:eb:55:41:9f:
+                    38:1e:22:4a:57:20:f4:83:59:49:c5:00:93:d3:33:
+                    02:92:d1:fc:f0:84:3b:4a:5b:8f:b6:73:9a:89:fa:
+                    30:1e:e6:2a:68:f2:91:ef:59:57:3d:dc:1c:52:6f:
+                    5e:e6:9b:b5:b8:7c:98:c9:13:d1:39:68:01:67:91:
+                    e0:d3:67:72:16:0a:5e:16:83:45:31:4f:b5:2b:b3:
+                    f6:40:86:89:3a:84:6e:6f:16:61:bc:70:84:be:5a:
+                    13:36:7b:82:ea:07:19:fc:18:c1:16:c6:32:0b:7d:
+                    2c:6b:c4:21:b9:38:6b:31:dc:d9:0c:ad:56:40:68:
+                    7c:e3:c6:64:8e:bf:1c:e0:72:3e:6c:db:d2:73:79:
+                    da:d7:c5:2f:5d:04:7d:b0:07:1e:95:dd:2a:47:5e:
+                    bf:3e:3a:c8:66:f6:67:0f:d4:2a:f1:e2:71:59:d2:
+                    6c:7b:a0:37:ac:e6:97:80:30:13:97:48:d5:74:fc:
+                    38:68:e4:57:cb:99:69:5a:84:27:ac:98:51:e4:64:
+                    bd:91:62:e8:58:27:06:2a:b9:0b:b8:08:e5:e5:b4:
+                    51:a7:a2:10:df:4e:07:6c:a0:3b:96:f2:6e:df:75:
+                    8c:97:1e:64:a0:9a:86:9b:98:26:f9:d8:b7:de:5b:
+                    21:b7:af:89:01:a3:f7:98:6b:da:19:ba:86:ef:ef:
+                    f1:ce:bb:2f:89:ed:c0:b6:1b:e5:5b:f8:90:11:9a:
+                    52:93:e9:be:f7:35:b9:08:cb:ba:c3:ed:2f:73:af:
+                    cc:96:07:55:b5:de:f6:03:f6:f1:89:f9:21:40:76:
+                    c1:69:f2:61:cc:9a:94:df:9c:ec:6a:65:38:be:d1:
+                    4e:2a:87:c7:2f:3e:53:ae:8b:9f:54:a1:09:59:64:
+                    25:aa:a9:d8:44:a9:a8:a0:71:e1:32:aa:4c:32:fd:
+                    44:28:cc:9c:6f:8e:db:81:7e:6f:fa:00:56:c5:e5:
+                    03:46:63:fb:8e:71:8d:e3:13:91:9f:ac:60:3e:64:
+                    f3:df:25:34:09:fa:2d:96:9f:16:05:ea:93:f5:e6:
+                    00:08:27:32:7b:3c:bd:ee:70:24:6c:3b:55:e9:db:
+                    f4:10:2d:20:06:b4:ca:e9:29:65:55:ad:f6:52:54:
+                    5f:e5:a3
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Key Usage: 
+                Digital Signature
+            X509v3 Subject Key Identifier: 
+                14:DF:34:D1:A8:7C:F3:76:25:AB:EC:03:9E:F2:BF:52:12:49:B9:69
+            X509v3 Authority Key Identifier: 
+                keyid:14:DF:34:D1:A8:7C:F3:76:25:AB:EC:03:9E:F2:BF:52:12:49:B9:69
+
+    Signature Algorithm: sha512WithRSAEncryption
+         30:e7:48:02:37:e9:28:cf:04:a2:4d:5c:fa:d8:4e:c9:76:c7:
+         14:3f:bd:2c:51:3d:33:f0:1a:bc:49:f1:47:95:8f:69:d8:a9:
+         54:14:44:6c:4d:9f:55:82:08:1e:c6:5b:d5:91:d9:bc:2e:b0:
+         af:d6:25:65:74:96:aa:36:de:ae:31:a8:11:f2:a4:2c:5a:e1:
+         4f:73:f8:4a:c3:35:b0:76:96:71:f2:b5:7d:4b:75:ee:5d:bf:
+         86:a5:ba:0b:a9:52:cb:ec:ab:e5:23:4b:f2:74:55:28:17:1e:
+         b3:ac:27:ad:45:13:6e:69:b3:5a:be:42:36:29:48:db:e7:5c:
+         22:58:a0:90:82:2c:2a:21:2b:db:f4:64:b7:91:5d:1f:2c:48:
+         a4:1a:85:e3:86:a5:aa:19:cd:19:e8:a5:fb:a3:7b:94:77:48:
+         25:a4:cf:a0:cf:71:82:5c:6f:71:22:7c:d6:97:a0:53:bb:ec:
+         30:f6:cb:16:fb:7b:fd:16:94:7a:53:6e:bd:04:64:a2:01:10:
+         9f:f0:5b:b5:a6:73:41:9d:5f:6f:45:73:0d:05:f7:30:6d:39:
+         90:b6:7d:55:7d:4c:2f:ae:5f:38:56:2f:8b:df:f4:bf:12:06:
+         93:6e:0d:02:23:bf:71:91:57:88:e8:bd:62:72:99:00:40:29:
+         1e:c9:13:11:da:7e:8e:e1:d2:a5:0d:bf:f7:d6:ec:01:0d:89:
+         41:cd:d5:dc:d2:f7:5f:33:0d:4c:2f:85:b7:85:b7:81:e4:17:
+         29:f0:74:cf:0e:15:8c:1a:50:0b:08:63:1a:91:4f:e7:76:97:
+         f1:d4:3b:7e:72:d4:c5:45:58:0c:6a:e9:0d:f2:85:d8:91:1e:
+         37:bd:78:e3:39:4d:2e:fd:85:31:c1:a6:3b:6a:cc:2c:53:72:
+         1d:8e:7b:f0:e6:76:86:09:6f:1a:f3:e4:a1:e2:dd:76:5f:b0:
+         8c:e2:2a:54:5d:c1:88:49:90:10:15:42:7d:05:24:53:8c:54:
+         ff:48:18:1a:36:e3:31:d3:54:32:78:0d:fe:f2:3d:aa:0d:37:
+         15:84:b4:36:47:31:e8:85:6e:0b:58:38:ff:21:91:09:c9:a8:
+         43:a3:ea:60:cb:7e:ed:f7:41:6f:4e:91:c1:fd:77:46:e7:d4:
+         e7:86:c0:1b:fd:50:6c:aa:be:00:b3:63:02:ff:4e:c7:a5:57:
+         6e:29:64:e9:54:d5:30:63:38:5f:2d:5a:db:49:5f:14:14:22:
+         d2:81:1f:61:9e:ee:ee:16:66:d6:bc:bd:ac:1b:5c:fb:38:31:
+         95:33:2e:84:6e:7a:de:ee:b9:fc:97:17:06:13:bf:70:1c:6e:
+         76:ed:66:38:e2:70:08:00
+-----BEGIN CERTIFICATE-----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=
+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/certs/ubuntu-drivers-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/certs/ubuntu-drivers-all.pem
@@ -0,0 +1,125 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number:
+            e9:df:13:0f:92:92:a9:b7
+        Signature Algorithm: sha512WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Kernel Module Signing
+        Validity
+            Not Before: May 31 16:06:09 2016 GMT
+            Not After : May 29 16:06:09 2026 GMT
+        Subject: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Kernel Module Signing
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                RSA Public-Key: (4096 bit)
+                Modulus:
+                    00:b3:b0:4f:c6:0a:77:8b:f9:d1:53:33:34:d2:80:
+                    b5:63:6f:e1:f6:a2:83:99:d5:b6:b1:e4:99:91:fa:
+                    6c:19:c6:d0:91:2a:b9:7d:b5:98:a6:0d:28:01:b8:
+                    7c:8e:aa:38:ec:51:37:33:96:f0:b0:9b:8d:86:5f:
+                    67:23:69:2f:d7:c2:f3:fb:c5:d7:f9:04:ff:f2:e5:
+                    61:68:b7:29:b9:c6:8e:4b:4d:2d:8f:92:0c:00:b3:
+                    a3:d2:5a:08:64:cd:f2:09:0b:a5:0e:e6:64:75:d5:
+                    41:f4:4d:49:3a:0d:dc:b9:27:8e:c4:d6:b1:df:8f:
+                    6c:f0:e4:f7:31:cb:a9:04:a1:f9:a7:aa:15:da:59:
+                    03:4d:46:14:d0:dd:bf:e0:f5:9e:f0:71:0c:70:78:
+                    2b:08:fb:e0:b6:68:a4:74:12:9d:f7:f2:64:88:17:
+                    2a:8a:ed:1a:91:b5:6c:13:bd:4c:10:0a:0b:72:0b:
+                    90:db:7d:f3:78:44:4c:d2:a5:41:f7:1c:77:7d:5a:
+                    8a:54:bc:8f:fe:b7:ee:e1:bc:59:37:c4:d4:e8:14:
+                    d0:5b:42:9b:04:00:8e:6d:83:8a:25:21:5b:08:c4:
+                    7b:b2:d9:99:52:c9:5e:59:6d:c4:aa:52:59:e2:e4:
+                    2f:7e:7e:ac:05:01:99:bf:13:72:b7:45:c5:17:da:
+                    8a:d5:3e:71:73:2e:d8:aa:e6:eb:5a:d0:9a:c4:93:
+                    f3:be:eb:d2:47:25:34:16:29:fa:dd:9a:2f:b1:20:
+                    e5:41:4e:ed:ea:51:7c:23:80:ba:3d:b5:3a:0b:8c:
+                    9c:85:48:6c:3c:8b:29:2f:2f:12:c7:52:34:02:ea:
+                    0f:ac:53:23:3c:f8:3e:40:1b:30:63:e9:2d:e6:f6:
+                    58:cc:51:f9:eb:08:4a:b4:c7:16:80:d1:8b:c2:64:
+                    6a:71:a9:70:31:a4:a7:3a:c0:93:99:1b:0e:42:c1:
+                    00:6d:43:27:99:6c:e5:fd:23:16:c1:8e:b5:66:17:
+                    2b:4c:53:5a:6d:1e:96:16:13:6a:c6:d4:85:5b:74:
+                    2e:ce:7c:45:2f:ad:cb:75:9e:5e:91:bd:9a:6a:86:
+                    1a:06:bd:39:be:a3:50:56:ea:e1:f6:e3:95:69:d7:
+                    31:e4:66:f7:36:b5:51:c2:22:b4:9c:74:9c:44:0b:
+                    0e:16:5f:53:f0:23:c6:b9:40:bd:d6:b8:7d:1b:f6:
+                    73:f6:27:e7:c0:e3:65:a0:58:ab:5c:59:b7:80:8c:
+                    8c:04:b4:a9:ae:a0:51:40:10:3b:63:59:49:87:d1:
+                    9b:df:a3:8c:c4:2e:eb:70:c1:0a:18:1f:cb:22:c2:
+                    f2:4a:65:0d:e5:81:74:d8:ce:72:c6:35:be:ba:63:
+                    72:c4:f9
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Key Usage: 
+                Digital Signature
+            X509v3 Subject Key Identifier: 
+                88:F7:52:E5:60:A1:E0:73:7E:31:16:3A:46:6A:D7:B7:0A:85:0C:19
+            X509v3 Authority Key Identifier: 
+                keyid:88:F7:52:E5:60:A1:E0:73:7E:31:16:3A:46:6A:D7:B7:0A:85:0C:19
+
+    Signature Algorithm: sha512WithRSAEncryption
+         04:85:16:27:58:ba:71:28:57:86:7b:c2:83:db:e5:72:6f:1e:
+         b2:1c:63:b0:db:ad:c0:42:96:c0:4f:65:f6:35:4d:c0:07:0d:
+         46:be:d3:1e:ec:f1:22:18:2a:18:5d:bb:69:a6:a6:d4:0d:c3:
+         57:03:b9:e7:45:49:28:ca:6d:98:17:68:97:cb:7b:36:81:0a:
+         37:9e:34:79:f3:e1:0e:5b:77:43:bb:5a:a5:45:b7:16:50:86:
+         fd:12:a4:96:0f:15:19:09:1c:e1:fa:80:a5:80:09:be:bb:c8:
+         26:0b:3e:de:03:d2:c2:18:a4:8d:0d:de:c5:32:82:0b:fb:75:
+         55:66:1a:2a:bb:e4:bd:25:91:20:15:d4:be:b8:3f:53:e3:fb:
+         a8:c3:55:e3:d5:e7:82:18:95:df:39:09:a7:fc:89:6e:b4:1c:
+         aa:2d:e8:67:c2:0d:34:34:3e:f9:fa:0b:ce:81:92:11:ae:12:
+         0a:fe:35:63:ce:46:29:c4:2b:4f:cb:4e:05:0a:a1:11:e2:35:
+         f6:5a:5d:b5:e8:d2:6f:4c:fc:3d:24:a6:03:4b:dd:98:6b:f2:
+         71:58:16:1d:a5:25:ef:d9:06:7c:e8:db:7b:88:6a:89:5c:59:
+         01:92:64:db:44:08:63:6c:7c:32:d6:55:98:63:09:26:61:67:
+         0a:fe:5d:ee:fd:23:59:b3:4d:91:c1:4d:41:8b:cd:20:58:fa:
+         2d:45:e5:bd:1d:69:5c:03:a0:49:a6:97:54:13:b6:c9:e0:f8:
+         56:83:a1:2a:c3:f4:6c:fd:ab:20:ca:3d:9c:95:c0:cf:04:bb:
+         46:39:cf:34:81:65:45:27:64:01:7d:62:b3:b8:72:ea:10:d5:
+         0f:53:7d:39:88:25:09:6f:8c:bc:e0:49:bb:39:e2:0e:8d:cf:
+         56:4d:c1:82:6d:87:d2:e7:fc:c0:9f:a7:65:60:d2:6c:65:18:
+         59:38:6e:d0:9c:d7:c3:81:9a:9a:29:8f:83:84:c3:b5:44:ff:
+         28:ac:13:17:64:f2:26:13:d9:55:06:b7:69:68:7c:bf:ec:d1:
+         8c:ef:b7:da:76:e1:07:73:c6:31:62:31:cb:b6:e1:e7:7f:0c:
+         c3:f7:4c:52:be:25:36:8e:a1:bb:60:02:c3:cb:3e:6f:29:fc:
+         7f:6a:fa:f8:ec:0a:df:49:e2:57:0e:bc:bd:93:c3:1b:d5:36:
+         8a:ff:d8:1b:17:c7:1f:cb:69:00:d2:54:9e:ad:61:89:92:95:
+         11:f8:ea:17:83:9f:9b:09:7d:b8:94:a4:ea:f5:ae:ea:dc:dd:
+         62:b9:9e:68:9c:18:ec:19:c4:13:08:c8:b1:62:ab:8e:84:69:
+         11:3c:da:ea:0d:b7:22:bd
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/changelog
+++ linux-xilinx-zynqmp-5.15.0/debian/changelog
@@ -0,0 +1,31125 @@
+linux-xilinx-zynqmp (5.15.0-1050.54) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1050.54 -proposed tracker (LP: #2110826)
+
+  [ Ubuntu: 5.15.0-142.152 ]
+
+  * jammy/linux: 5.15.0-142.152 -proposed tracker (LP: #2110829)
+  * Rotate the Canonical Livepatch key (LP: #2111244)
+    - [Config] Prepare for Canonical Livepatch key rotation
+  * Jammy generic-64k fails to initialize gVNIC devices (LP: #2109537)
+    - gve: Perform adminq allocations through a dma_pool.
+    - gve: Deprecate adminq_pfn for pci revision 0x1.
+    - gve: Remove obsolete checks that rely on page size.
+    - gve: Add page size register to the register_page_list command.
+    - gve: Remove dependency on 4k page size.
+  * CVE-2025-2312 cifs.upcall could access incorrect kerberos credentials cache
+    (LP: #2099914) // CVE-2025-2312
+    - CIFS: New mount option for cifs.upcall namespace resolution
+  * [UBUNTU 22.04] net/smc: fix neighbour and rtable leak in smc_ib_find_route()
+    (LP: #2109601) // CVE-2024-36945
+    - net/smc: fix neighbour and rtable leak in smc_ib_find_route()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355)
+    - clockevents/drivers/i8253: Fix stop sequence for timer 0
+    - sched/isolation: Prevent boot crash when the boot CPU is nohz_full
+    - fbdev: hyperv_fb: iounmap() the correct memory when removing a device
+    - pinctrl: bcm281xx: Fix incorrect regmap max_registers value
+    - netfilter: nft_ct: Use __refcount_inc() for per-CPU nft_ct_pcpu_template.
+    - net: dsa: mv88e6xxx: Verify after ATU Load ops
+    - netpoll: hold rcu read lock in __netpoll_send_skb()
+    - Drivers: hv: vmbus: Don't release fb_mmio resource in vmbus_free_mmio()
+    - ipvs: prevent integer overflow in do_ip_vs_get_ctl()
+    - netfilter: nft_exthdr: fix offset with ipv4_find_option()
+    - gre: Fix IPv6 link-local address generation.
+    - slab: clean up function prototypes
+    - slab: Introduce kmalloc_size_roundup()
+    - openvswitch: Use kmalloc_size_roundup() to match ksize() usage
+    - net: openvswitch: remove misbehaving actions length check
+    - net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices
+    - nvme-fc: go straight to connecting state when initializing
+    - hrtimers: Mark is_migration_base() with __always_inline
+    - powercap: call put_device() on an error path in
+      powercap_register_control_type()
+    - scsi: core: Use GFP_NOIO to avoid circular locking dependency
+    - ACPI: resource: IRQ override for Eluktronics MECH-17
+    - alpha/elf: Fix misc/setarch test of util-linux by removing 32bit support
+    - vboxsf: fix building with GCC 15
+    - HID: intel-ish-hid: fix the length of MNG_SYNC_FW_CLOCK in doorbell
+    - sched: Clarify wake_up_q()'s write to task->wake_q.next
+    - s390/cio: Fix CHPID "configure" attribute caching
+    - thermal/cpufreq_cooling: Remove structure member documentation
+    - ASoC: rsnd: don't indicate warning on rsnd_kctrl_accept_runtime()
+    - ASoC: arizona/madera: use fsleep() in up/down DAPM event delays.
+    - ASoC: SOF: Intel: hda: add softdep pre to snd-hda-codec-hdmi module
+    - net: wwan: mhi_wwan_mbim: Silence sequence number glitch errors
+    - nvmet-rdma: recheck queue state is LIVE in state lock in recv done
+    - sctp: Fix undefined behavior in left shift operation
+    - nvme: only allow entering LIVE from CONNECTING state
+    - ASoC: tas2770: Fix volume scale
+    - ASoC: tas2764: Fix power control mask
+    - ASoC: tas2764: Set the SDOUT polarity correctly
+    - fuse: don't truncate cached, mutated symlink
+    - x86/irq: Define trace events conditionally
+    - mptcp: safety check before fallback
+    - drm/nouveau: Do not override forced connector status
+    - block: fix 'kmem_cache of name 'bio-108' already exists'
+    - USB: serial: ftdi_sio: add support for Altera USB Blaster 3
+    - USB: serial: option: add Telit Cinterion FE990B compositions
+    - USB: serial: option: fix Telit Cinterion FE990A name
+    - USB: serial: option: match on interface class for Telit FN990B
+    - drm/atomic: Filter out redundant DPMS calls
+    - drm/amd/display: Restore correct backlight brightness after a GPU reset
+    - qlcnic: fix memory leak issues in qlcnic_sriov_common.c
+    - lib/buildid: Handle memfd_secret() files in build_id_parse()
+    - tcp: fix races in tcp_abort()
+    - ASoC: ops: Consistently treat platform_max as control value
+    - drm/gma500: Add NULL check for pci_gfx_root in mid_get_vbt_data()
+    - ASoC: codecs: wm0010: Fix error handling path in wm0010_spi_probe()
+    - cifs: Fix integer overflow while processing actimeo mount option
+    - i2c: ali1535: Fix an error handling path in ali1535_probe()
+    - i2c: ali15x3: Fix an error handling path in ali15x3_probe()
+    - i2c: sis630: Fix an error handling path in sis630_probe()
+    - drm/amd/display: Check for invalid input params when building scaling params
+    - smb: client: Fix match_session bug preventing session reuse
+    - Revert "smb: client: fix potential UAF in cifs_debug_files_proc_show()"
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+    - firmware: imx-scu: fix OF node leak in .probe()
+    - xfrm_output: Force software GSO only in tunnel mode
+    - ARM: dts: bcm2711: PL011 UARTs are actually r1p5
+    - RDMA/bnxt_re: Add missing paranthesis in map_qp_id_to_tbl_indx
+    - ARM: dts: bcm2711: Don't mark timer regs unconfigured
+    - RDMA/bnxt_re: Avoid clearing VLAN_ID mask in modify qp path
+    - RDMA/hns: Remove redundant 'phy_addr' in hns_roce_hem_list_find_mtt()
+    - RDMA/hns: Fix unmatched condition in error path of alloc_user_qp_db()
+    - RDMA/hns: Fix a missing rollback in error path of
+      hns_roce_create_qp_common()
+    - RDMA/hns: Fix wrong value of max_sge_rd
+    - ipv6: Set errno after ip_fib_metrics_init() in ip6_route_info_create().
+    - net/neighbor: add missing policy for NDTPA_QUEUE_LENBYTES
+    - Revert "gre: Fix IPv6 link-local address generation."
+    - i2c: omap: fix IRQ storms
+    - drm/v3d: Don't run jobs that have errors flagged in its fence
+    - mmc: atmel-mci: Add missing clk_disable_unprepare()
+    - ARM: shmobile: smp: Enforce shmobile_smp_* alignment
+    - batman-adv: Ignore own maximum aggregation size during RX
+    - drm/amdgpu: Fix JPEG video caps max size for navi1x and raven
+    - mptcp: Fix data stream corruption in the address announcement
+    - arm64: dts: rockchip: fix u2phy1_host status for NanoPi R4S
+    - ALSA: usb-audio: Add quirk for Plantronics headsets to fix control names
+    - HID: hid-plantronics: Add mic mute mapping and generalize quirks
+    - ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed()
+    - ARM: 9351/1: fault: Add "cut here" line for prefetch aborts
+    - ARM: Remove address checking for MMUless devices
+    - ALSA: hda/realtek: Support mute LED on HP Laptop 15s-du3xxx
+    - counter: stm32-lptimer-cnt: fix error handling when enabling
+    - counter: microchip-tcb-capture: Fix undefined counter channel state on probe
+    - tty: serial: 8250: Add some more device IDs
+    - tty: serial: 8250: Add Brainboxes XC devices
+    - net: usb: qmi_wwan: add Telit Cinterion FN990B composition
+    - net: usb: qmi_wwan: add Telit Cinterion FE990B composition
+    - net: usb: usbnet: restore usb%d name exception for local mac addresses
+    - serial: 8250_dma: terminate correct DMA in tx_dma_flush()
+    - x86/mm/pat: cpa-test: fix length for CPA_ARRAY test
+    - cpufreq: scpi: compare kHz instead of Hz
+    - cpufreq: governor: Fix negative 'idle_time' handling in dbs_update()
+    - x86/fpu: Avoid copying dynamic FP state from init_task in
+      arch_dup_task_struct()
+    - x86/platform: Only allow CONFIG_EISA for 32-bit
+    - [Config] updateconfigs for HAVE_EISA
+    - PM: sleep: Adjust check before setting power.must_resume
+    - selinux: Chain up tool resolving errors in install_policy.sh
+    - EDAC/ie31200: Fix the size of EDAC_MC_LAYER_CHIP_SELECT layer
+    - EDAC/ie31200: Fix the DIMM size mask for several SoCs
+    - EDAC/ie31200: Fix the error path order of ie31200_init()
+    - PM: sleep: Fix handling devices with direct_complete set on errors
+    - lockdep: Don't disable interrupts on RT in disable_irq_nosync_lockdep.*()
+    - perf/ring_buffer: Allow the EPOLLRDNORM flag for poll
+    - media: platform: allgro-dvt: unregister v4l2_device on the error path
+    - HID: remove superfluous (and wrong) Makefile entry for
+      CONFIG_INTEL_ISH_FIRMWARE_DOWNLOADER
+    - ALSA: hda/realtek: Always honor no_shutup_pins
+    - ASoC: ti: j721e-evm: Fix clock configuration for ti,j7200-cpb-audio
+      compatible
+    - drm/bridge: ti-sn65dsi86: Fix multiple instances
+    - drm/dp_mst: Fix drm RAD print
+    - drm: xlnx: zynqmp: Fix max dma segment size
+    - drm/mediatek: mtk_hdmi: Unregister audio platform device on failure
+    - drm/mediatek: mtk_hdmi: Fix typo for aud_sampe_size member
+    - PCI: cadence-ep: Fix the driver to send MSG TLP for INTx without data
+      payload
+    - PCI: brcmstb: Use internal register to change link capability
+    - PCI/portdrv: Only disable pciehp interrupts early when needed
+    - PCI: Avoid reset when disabled via sysfs
+    - drm/amd/display: fix type mismatch in CalculateDynamicMetadataParameters()
+    - PCI: Remove stray put_device() in pci_register_host_bridge()
+    - PCI: xilinx-cpm: Fix IRQ domain leak in error path of probe
+    - drm/mediatek: dsi: fix error codes in mtk_dsi_host_transfer()
+    - PCI: pciehp: Don't enable HPIE when resuming in poll mode
+    - fbdev: au1100fb: Move a variable assignment behind a null pointer check
+    - mdacon: rework dependency list
+    - fbdev: sm501fb: Add some geometry checks.
+    - clk: amlogic: gxbb: drop incorrect flag on 32k clock
+    - crypto: hisilicon/sec2 - fix for aead authsize alignment
+    - of: property: Increase NR_FWNODE_REFERENCE_ARGS
+    - remoteproc: qcom_q6v5_pas: Make single-PD handling more robust
+    - libbpf: Fix hypothetical STT_SECTION extern NULL deref case
+    - clk: qcom: gcc-msm8953: fix stuck venus0_core0 clock
+    - bpf: Use preempt_count() directly in bpf_send_signal_common()
+    - lib: 842: Improve error handling in sw842_compress()
+    - pinctrl: renesas: rza2: Fix missing of_node_put() call
+    - pinctrl: renesas: rzg2l: Fix missing of_node_put() call
+    - clk: rockchip: rk3328: fix wrong clk_ref_usb3otg parent
+    - remoteproc: qcom_q6v5_mss: Handle platforms with one power domain
+    - IB/mad: Check available slots before posting receive WRs
+    - pinctrl: tegra: Set SFIO mode to Mux Register
+    - clk: amlogic: g12b: fix cluster A parent data
+    - clk: amlogic: gxbb: drop non existing 32k clock parent
+    - clk: amlogic: g12a: fix mmc A peripheral clock
+    - x86/entry: Fix ORC unwinder for PUSH_REGS with save_ret=1
+    - power: supply: max77693: Fix wrong conversion of charge input threshold
+      value
+    - crypto: nx - Fix uninitialised hv_nxc on error
+    - mfd: sm501: Switch to BIT() to mitigate integer overflows
+    - x86/dumpstack: Fix inaccurate unwinding from exception stacks due to
+      misplaced assignment
+    - crypto: hisilicon/sec2 - fix for aead auth key length
+    - clk: qcom: mmcc-sdm660: fix stuck video_subcore0 clock
+    - isofs: fix KMSAN uninit-value bug in do_isofs_readdir()
+    - soundwire: slave: fix an OF node reference leak in soundwire slave device
+    - coresight: catu: Fix number of pages while using 64k pages
+    - iio: accel: mma8452: Ensure error return on failure to matching oversampling
+      ratio
+    - iio: adc: ad7124: Fix comparison of channel configs
+    - perf units: Fix insufficient array space
+    - kexec: initialize ELF lowest address to ULONG_MAX
+    - NFSv4: Don't trigger uneccessary scans for return-on-close delegations
+    - fuse: fix dax truncate/punch_hole fault path
+    - i3c: master: svc: Fix missing the IBI rules
+    - perf python: Fixup description of sample.id event member
+    - perf python: Decrement the refcount of just created event on failure
+    - perf python: Don't keep a raw_data pointer to consumed ring buffer space
+    - perf python: Check if there is space to copy all the event
+    - fs/procfs: fix the comment above proc_pid_wchan()
+    - objtool, media: dib8000: Prevent divide-by-zero in dib8000_set_dds()
+    - exfat: fix the infinite loop in exfat_find_last_cluster()
+    - ksmbd: fix multichannel connection failure
+    - ring-buffer: Fix bytes_dropped calculation issue
+    - ACPI: processor: idle: Return an error if both P_LVL{2,3} idle states are
+      invalid
+    - octeontx2-af: Fix mbox INTR handler when num VFs > 64
+    - octeontx2-af: Free NIX_AF_INT_VEC_GEN irq
+    - sched/smt: Always inline sched_smt_active()
+    - wifi: iwlwifi: fw: allocate chained SG tables for dump
+    - nvme-tcp: fix possible UAF in nvme_tcp_poll
+    - nvme-pci: clean up CMBMSC when registering CMB fails
+    - nvme-pci: skip CMB blocks incompatible with PCI P2P DMA
+    - affs: generate OFS sequence numbers starting at 1
+    - affs: don't write overlarge OFS data block size fields
+    - sched/deadline: Use online cpus for validating runtime
+    - locking/semaphore: Use wake_q to wake up processes outside lock critical
+      section
+    - x86/sgx: Warn explicitly if X86_FEATURE_SGX_LC is not enabled
+    - drm/amd: Keep display off while going into S4
+    - ALSA: hda/realtek: Add mute LED quirk for HP Pavilion x360 14-dy1xxx
+    - can: statistics: use atomic access in hot path
+    - hwmon: (nct6775-core) Fix out of bounds access for NCT679{8,9}
+    - riscv: ftrace: Add parentheses in macro definitions of make_call_t0 and
+      make_call_ra
+    - ntb: intel: Fix using link status DB's
+    - netfilter: nft_set_hash: GC reaps elements with conncount for dynamic sets
+      only
+    - vsock: avoid timeout during connect() if the socket is closing
+    - tunnels: Accept PACKET_HOST in skb_tunnel_check_pmtu().
+    - ipv6: fix omitted netlink attributes when using RTEXT_FILTER_SKIP_STATS
+    - can: flexcan: only change CAN state when link up in system PM
+    - can: flexcan: disable transceiver during system PM
+    - mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0
+    - mmc: sdhci-brcmstb: add cqhci suspend/resume to PM ops
+    - tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
+    - tty: serial: fsl_lpuart: disable transmitter before changing RS485 related
+      registers
+    - platform/x86: ISST: Correct command storage data length
+    - ntb_perf: Delete duplicate dmaengine_unmap_put() call in perf_copy_chunk()
+    - x86/tsc: Always save/restore TSC sched_clock() on suspend/resume
+    - ACPI: resource: Skip IRQ override on ASUS Vivobook 14 X1404VAP
+    - mmc: sdhci-pxav3: set NEED_RSP_BUSY capability
+    - tracing: Ensure module defining synth event cannot be unloaded while tracing
+    - tracing: Fix synth event printk format for str fields
+    - tracing/osnoise: Fix possible recursive locking for cpus_read_lock()
+    - ext4: don't over-report free space or inodes in statvfs
+    - jfs: add index corruption check to DT_GETPAGE()
+    - NFSD: Skip sending CB_RECALL_ANY when the backchannel isn't up
+    - mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
+    - mm, slab: remove duplicate kernel-doc comment for ksize()
+    - tracing: Do not use PERF enums when perf is not defined
+    - mmc: sdhci-brcmstb: Initialize base_clk to NULL in sdhci_brcmstb_probe()
+    - Linux 5.15.180
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22025
+    - nfsd: put dl_stid if fail to queue dl_recall
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-39735
+    - jfs: fix slab-out-of-bounds read in ea_get()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-37785
+    - ext4: fix OOB read when checking dotdot dir
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22035
+    - tracing: Fix use-after-free in print_graph_function_flags during tracer
+      switching
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22044
+    - acpi: nfit: fix narrowing conversion in acpi_nfit_ctl
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22045
+    - x86/mm: Fix flush_tlb_range() when used for zapping normal PMDs
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46753
+    - btrfs: handle errors from btrfs_dec_ref() properly
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22050
+    - usbnet:fix NPE during rx_complete
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46812
+    - drm/amd/display: Skip inactive planes within
+      ModeSupportAndSystemConfiguration
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-46821
+    - drm/amd/pm: Fix negative array index read
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22054
+    - arcnet: Add NULL check in com20020pci_probe()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22055
+    - net: fix geneve_opt length integer overflow
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22056
+    - netfilter: nft_tunnel: fix geneve_opt type confusion addition
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22060
+    - net: mvpp2: Prevent parser TCAM memory corruption
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38637
+    - net_sched: skbprio: Remove overly strict queue assertions
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22063
+    - netlabel: Fix NULL pointer exception caused by CALIPSO on IPv4 sockets
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22066
+    - ASoC: imx-card: Add NULL check in imx_card_probe()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2023-53034
+    - ntb_hw_switchtec: Fix shift-out-of-bounds in switchtec_ntb_mw_set_trans
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22071
+    - spufs: fix a leak in spufs_create_context()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22073
+    - spufs: fix a leak on spufs_new_file() failure
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21994
+    - ksmbd: fix incorrect validation for num_aces field of smb_acl
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38575
+    - ksmbd: use aead_request_free to match aead_request_alloc
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22075
+    - rtnetlink: Allocate vfinfo size for VF GUIDs when supported
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22079
+    - ocfs2: validate l_tree_depth to avoid out-of-bounds access
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22081
+    - fs/ntfs3: Fix a couple integer overflows on 32bit systems
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22086
+    - RDMA/mlx5: Fix mlx5_poll_one() cur_qp update flow
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22089
+    - RDMA/core: Don't expose hw_counters outside of init net namespace
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-39728
+    - clk: samsung: Fix UBSAN panic in samsung_clk_init()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-38152
+    - remoteproc: core: Clear table_sz when rproc_shutdown
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-58093
+    - PCI/ASPM: Fix link state exit during switch upstream function removal
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22097
+    - drm/vkms: Fix use after free and double free on init error
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-23136
+    - thermal: int340x: Add NULL check for adev
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-23138
+    - watch_queue: fix pipe accounting mismatch
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22020
+    - memstick: rtsx_usb_ms: Fix slab-use-after-free in rtsx_usb_ms_drv_remove
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22021
+    - netfilter: socket: Lookup orig tuple for IPv6 SNAT
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22018
+    - atm: Fix NULL pointer dereference
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-56664
+    - bpf, sockmap: Fix race between element replace and close()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2024-53144 // CVE-2024-8805
+    - Bluetooth: hci_event: Align BR/EDR JUST_WORKS paring with LE
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21996
+    - drm/radeon: fix uninitialized size issue in radeon_vce_cs_parse()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22014
+    - soc: qcom: pdr: Fix the potential deadlock
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21999
+    - proc: fix UAF in proc_get_inode()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22008
+    - regulator: check that dummy regulator has been probed before using it
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22004
+    - net: atm: fix use after free in lec_send()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22005
+    - ipv6: Fix memleak of nhc_pcpu_rth_output in fib_check_nh_v6_gw().
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22007
+    - Bluetooth: Fix error code in chan_alloc_skb_cb()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-22010
+    - RDMA/hns: Fix soft lockup during bt pages loop
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21941
+    - drm/amd/display: Fix null check for pipe_ctx->plane_state in
+      resource_build_scaling_params
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21962
+    - cifs: Fix integer overflow while processing closetimeo mount option
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21963
+    - cifs: Fix integer overflow while processing acdirmax mount option
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21964
+    - cifs: Fix integer overflow while processing acregmax mount option
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21968
+    - drm/amd/display: Fix slab-use-after-free on hdcp_work
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21956
+    - drm/amd/display: Assign normalized_pix_clk when color depth = 14
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21991
+    - x86/microcode/AMD: Fix out-of-bounds on systems with CPU-less NUMA nodes
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21992
+    - HID: ignore non-functional sensor in HP 5MP Camera
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21957
+    - scsi: qla1280: Fix kernel oops when debug level > 2
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21970
+    - net/mlx5: Bridge, fix the crash caused by LAG state check
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21959
+    - netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in
+      insert_tree()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21975
+    - net/mlx5: handle errors in mlx5_chains_create_table()
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2025-21981
+    - ice: fix memory leak in aRFS after reset
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2022-49728
+    - ipv6: Fix signed integer overflow in __ip6_append_data
+  * Jammy update: v5.15.180 upstream stable release (LP: #2109355) //
+    CVE-2022-49636
+    - vlan: fix memory leak in vlan_newlink()
+  * VM boots slowly with large-BAR GPU Passthrough due to pci/probe.c redundancy
+    (LP: #2097389)
+    - PCI: Batch BAR sizing operations
+  * kexec fails in LPAR when some cpus are disabled (LP: #2075575)
+    - powerpc/pseries: Fix scv instruction crash with kexec
+  * CVE-2024-56608
+    - drm/amd/display: Fix out-of-bounds access in 'dcn21_link_encoder_create'
+  * CVE-2024-53168
+    - net: make sock_inuse_add() available
+    - sunrpc: fix one UAF issue caused by sunrpc kernel tcp socket
+  * CVE-2024-56551
+    - drm/amdgpu: fix usage slab after free
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 06 Jun 2025 13:34:47 +0800
+
+linux-xilinx-zynqmp (5.15.0-1049.53) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1049.53 -proposed tracker (LP: #2111049)
+
+  [ Ubuntu: 5.15.0-141.151 ]
+
+  * jammy/linux: 5.15.0-141.151 -proposed tracker (LP: #2111052)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+  * CVE-2024-56608
+    - drm/amd/display: Fix out-of-bounds access in 'dcn21_link_encoder_create'
+  * CVE-2024-53168
+    - net: make sock_inuse_add() available
+    - sunrpc: fix one UAF issue caused by sunrpc kernel tcp socket
+  * CVE-2024-56551
+    - drm/amdgpu: fix usage slab after free
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Wed, 28 May 2025 13:53:46 +0800
+
+linux-xilinx-zynqmp (5.15.0-1048.52) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1048.52 -proposed tracker (LP: #2106990)
+
+  [ Ubuntu: 5.15.0-140.150 ]
+
+  * jammy/linux: 5.15.0-140.150 -proposed tracker (LP: #2106996)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.04.14)
+  * NFS, overlay, fstab issue after update to kernel 5.15.0-133-generic and -134
+    (LP: #2103598)
+    - udf: Fix directory iteration for longer tail extents
+  * Remove floppy kernel module causes null pointer deference (LP: #2104326)
+    - floppy: fix add_disk() assumption on exit due to new developments
+  * CVE-2025-21971
+    - net_sched: Prevent creation of classes with TC_H_ROOT
+  * CVE-2024-56599
+    - wifi: ath10k: avoid NULL pointer error during sdio remove
+  * CVE-2024-56721
+    - x86/CPU/AMD: Terminate the erratum_1386_microcode array
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026)
+    - afs: Fix EEXIST error returned from afs_rmdir() to be ENOTEMPTY
+    - afs: Fix directory format encoding struct
+    - hung_task: move hung_task sysctl interface to hung_task.c
+    - sysctl: use const for typically used max/min proc sysctls
+    - sysctl: share unsigned long const values
+    - fs: move inode sysctls to its own file
+    - fs: move fs stat sysctls to file_table.c
+    - fs: fix proc_handler for sysctl_nr_open
+    - block: deprecate autoloading based on dev_t
+    - block: retry call probe after request_module in blk_request_module
+    - pstore/blk: trivial typo fixes
+    - nvme: Add error check for xa_store in nvme_get_effects_log
+    - partitions: ldm: remove the initial kernel-doc notation
+    - select: Fix unbalanced user_access_end()
+    - afs: Fix the fallback handling for the YFS.RemoveFile2 RPC call
+    - sched/psi: Use task->psi_flags to clear in CPU migration
+    - sched/fair: Fix value reported by hot tasks pulled in /proc/schedstat
+    - drm/etnaviv: Fix page property being used for non writecombine buffers
+    - genirq: Make handle_enforce_irqctx() unconditionally available
+    - wifi: rtlwifi: do not complete firmware loading needlessly
+    - wifi: rtlwifi: rtl8192se: rise completion of firmware loading as last step
+    - wifi: rtlwifi: wait for firmware loading before releasing memory
+    - wifi: rtlwifi: fix init_sw_vars leak when probe fails
+    - wifi: rtlwifi: usb: fix workqueue leak when probe fails
+    - spi: zynq-qspi: Add check for clk_enable()
+    - dt-bindings: mmc: controller: clarify the address-cells description
+    - spi: dt-bindings: add schema listing peripheral-specific properties
+    - dt-bindings: Another pass removing cases of 'allOf' containing a '$ref'
+    - dt-bindings: leds: Add Qualcomm Light Pulse Generator binding
+    - dt-bindings: leds: Optional multi-led unit address
+    - dt-bindings: leds: Add multicolor PWM LED bindings
+    - dt-bindings: leds: class-multicolor: reference class directly in multi-led
+      node
+    - dt-bindings: leds: class-multicolor: Fix path to color definitions
+    - rtlwifi: replace usage of found with dedicated list iterator variable
+    - wifi: rtlwifi: remove unused timer and related code
+    - wifi: rtlwifi: remove unused dualmac control leftovers
+    - wifi: rtlwifi: destroy workqueue at rtl_deinit_core
+    - wifi: rtlwifi: pci: wait for firmware loading before releasing memory
+    - HID: multitouch: Add support for lenovo Y9000P Touchpad
+    - Revert "HID: multitouch: Add support for lenovo Y9000P Touchpad"
+    - HID: multitouch: fix support for Goodix PID 0x01e9
+    - regulator: dt-bindings: mt6315: Drop regulator-compatible property
+    - ACPI: fan: cleanup resources in the error path of .probe()
+    - cpupower: fix TSC MHz calculation
+    - dt-bindings: mfd: bd71815: Fix rsense and typos
+    - leds: netxbig: Fix an OF node reference leak in netxbig_leds_get_of_pdata()
+    - cpufreq: schedutil: Fix superfluous updates caused by need_freq_update
+    - clk: imx8mp: Fix clkout1/2 support
+    - regulator: of: Implement the unwind path of of_regulator_match()
+    - samples/landlock: Fix possible NULL dereference in parse_path()
+    - wifi: wlcore: fix unbalanced pm_runtime calls
+    - net/smc: fix data error when recvmsg with MSG_PEEK flag
+    - landlock: Move filesystem helpers and add a new one
+    - wifi: mt76: mt76u_vendor_request: Do not print error messages when -EPROTO
+    - cpufreq: ACPI: Fix max-frequency computation
+    - selftests: harness: fix printing of mismatch values in __EXPECT()
+    - wifi: cfg80211: Handle specific BSSID in 6GHz scanning
+    - wifi: cfg80211: adjust allocation of colocated AP data
+    - clk: analogbits: Fix incorrect calculation of vco rate delta
+    - selftests/landlock: Fix error message
+    - net/mlxfw: Drop hard coded max FW flash image size
+    - netfilter: nft_flow_offload: update tcp state flags under lock
+    - tcp_cubic: fix incorrect HyStart round start detection
+    - tools/testing/selftests/bpf/test_tc_tunnel.sh: Fix wait for server bind
+    - libbpf: Fix segfault due to libelf functions not setting errno
+    - ASoC: sun4i-spdif: Add clock multiplier settings
+    - perf header: Fix one memory leakage in process_bpf_btf()
+    - perf header: Fix one memory leakage in process_bpf_prog_info()
+    - perf bpf: Fix two memory leakages when calling
+      perf_env__insert_bpf_prog_info()
+    - ASoC: renesas: rz-ssi: Use only the proper amount of dividers
+    - ktest.pl: Remove unused declarations in run_bisect_test function
+    - crypto: hisilicon/sec - add some comments for soft fallback
+    - crypto: hisilicon/sec - delete redundant blank lines
+    - crypto: hisilicon/sec2 - optimize the error return process
+    - crypto: hisilicon/sec2 - fix for aead icv error
+    - crypto: hisilicon/sec2 - fix for aead invalid authsize
+    - crypto: ixp4xx - fix OF node reference leaks in init_ixp_crypto()
+    - padata: fix sysfs store callback check
+    - perf top: Don't complain about lack of vmlinux when not resolving some
+      kernel samples
+    - perf report: Fix misleading help message about --demangle
+    - padata: add pd get/put refcnt helper
+    - ARM: at91: pm: change BU Power Switch to automatic mode
+    - arm64: dts: mt8183: set DMIC one-wire mode on Damu
+    - arm64: dts: mediatek: mt8516: fix GICv2 range
+    - arm64: dts: mediatek: mt8516: fix wdt irq type
+    - arm64: dts: mediatek: mt8516: remove 2 invalid i2c clocks
+    - arm64: dts: mediatek: mt8516: add i2c clock-div property
+    - arm64: dts: mediatek: mt8516: reserve 192 KiB for TF-A
+    - RDMA/mlx4: Avoid false error about access to uninitialized gids array
+    - arm64: dts: mediatek: mt8173-evb: Drop regulator-compatible property
+    - arm64: dts: mediatek: mt8173-elm: Drop regulator-compatible property
+    - arm64: dts: mediatek: mt8173-elm: Fix MT6397 PMIC sub-node names
+    - arm64: dts: mediatek: mt8173-evb: Fix MT6397 PMIC sub-node names
+    - arm64: dts: mediatek: mt8183: kenzo: Support second source touchscreen
+    - arm64: dts: mediatek: mt8183: willow: Support second source touchscreen
+    - memory: Add LPDDR2-info helpers
+    - memory: tegra20-emc: Support matching timings by LPDDR2 configuration
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Drop pp3300_panel voltage
+      settings
+    - arm64: dts: qcom: msm8996: Fix up USB3 interrupts
+    - arm64: dts: qcom: msm8994: Describe USB interrupts
+    - arm64: dts: qcom: msm8916: correct sleep clock frequency
+    - arm64: dts: qcom: msm8994: correct sleep clock frequency
+    - arm64: dts: qcom: sc7280: correct sleep clock frequency
+    - arm64: dts: qcom: sm6125: correct sleep clock frequency
+    - arm64: dts: qcom: sm8250: correct sleep clock frequency
+    - arm64: dts: qcom: sm8350: correct sleep clock frequency
+    - arm64: dts: qcom: sm8150-microsoft-surface-duo: fix typos in da7280
+      properties
+    - arm64: dts: qcom: sdm845: Fix interrupt types of camss interrupts
+    - ARM: dts: mediatek: mt7623: fix IR nodename
+    - fbdev: omapfb: Fix an OF node leak in dss_of_port_get_parent_device()
+    - RDMA/mlx5: Remove iova from struct mlx5_core_mkey
+    - RDMA/mlx5: Enforce umem boundaries for explicit ODP page faults
+    - RDMA/mlx5: Fix indirect mkey ODP page count
+    - xen/x86: free_p2m_page: use memblock_free_ptr() to free a virtual pointer
+    - memblock: drop memblock_free_early_nid() and memblock_free_early()
+    - of: reserved-memory: Do not make kmemleak ignore freed address
+    - efi: sysfb_efi: fix W=1 warnings when EFI is not set
+    - media: rc: iguanair: handle timeouts
+    - media: lmedm04: Handle errors for lme2510_int_read
+    - PCI: endpoint: Destroy the EPC device in devm_pci_epc_destroy()
+    - media: marvell: Add check for clk_enable()
+    - media: i2c: imx412: Add missing newline to prints
+    - media: i2c: ov9282: Correct the exposure offset
+    - media: mipi-csis: Add check for clk_enable()
+    - media: camif-core: Add check for clk_enable()
+    - media: uvcvideo: Propagate buf->error to userspace
+    - mtd: hyperbus: Make hyperbus_unregister_device() return void
+    - mtd: hyperbus: hbmc-am654: Convert to platform remove callback returning
+      void
+    - mtd: hyperbus: hbmc-am654: fix an OF node reference leak
+    - staging: media: imx: fix OF node leak in imx_media_add_of_subdevs()
+    - scsi: mpt3sas: Set ioc->manu_pg11.EEDPTagMode directly to 1
+    - scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
+    - ocfs2: mark dquot as inactive if failed to start trans while releasing dquot
+    - module: Extend the preempt disabled section in
+      dereference_symbol_descriptor().
+    - NFSv4.2: fix COPY_NOTIFY xdr buf size calculation
+    - NFSv4.2: mark OFFLOAD_CANCEL MOVEABLE
+    - tools/bootconfig: Fix the wrong format specifier
+    - xfrm: replay: Fix the update of replay_esn->oseq_hi for GSO
+    - dmaengine: ti: edma: fix OF node reference leaks in edma_driver
+    - gpio: mxc: remove dead code after switch to DT-only
+    - net: fec: implement TSO descriptor cleanup
+    - PM: hibernate: Add error handling for syscore_suspend()
+    - net: netdevsim: try to close UDP port harness races
+    - ptp: Properly handle compat ioctls
+    - perf trace: Fix runtime error of index out of bounds
+    - vsock: Allow retrying on connect() failure
+    - bgmac: reduce max frame size to support just MTU 1500
+    - net: sh_eth: Fix missing rtnl lock in suspend/resume path
+    - net: hsr: fix fill_frame_info() regression vs VLAN packets
+    - genksyms: fix memory leak when the same symbol is added from source
+    - genksyms: fix memory leak when the same symbol is read from *.symref file
+    - kconfig: fix file name in warnings when loading KCONFIG_DEFCONFIG_LIST
+    - kconfig: add warn-unknown-symbols sanity check
+    - kconfig: require a space after '#' for valid input
+    - kconfig: remove unused code for S_DEF_AUTO in conf_read_simple()
+    - kconfig: deduplicate code in conf_read_simple()
+    - kconfig: WERROR unmet symbol dependency
+    - kconfig: fix memory leak in sym_warn_unmet_dep()
+    - hexagon: fix using plain integer as NULL pointer warning in cmpxchg
+    - hexagon: Fix unbalanced spinlock in die()
+    - f2fs: Introduce linear search for dentries
+    - ktest.pl: Check kernelrelease return in get_version
+    - ALSA: usb-audio: Add delay quirk for iBasso DC07 Pro
+    - drivers/card_reader/rtsx_usb: Restore interrupt based detection
+    - usb: gadget: f_tcm: Fix Get/SetInterface return value
+    - usb: dwc3: core: Defer the probe until USB power supply ready
+    - usb: typec: tcpm: set SRC_SEND_CAPABILITIES timeout to PD_T_SENDER_RESPONSE
+    - usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS
+    - btrfs: output the reason for open_ctree() failure
+    - btrfs: fix data race when accessing the inode's disk_i_size at
+      btrfs_drop_extents()
+    - btrfs: convert BUG_ON in btrfs_reloc_cow_block() to proper error handling
+    - sched: Don't try to catch up excess steal time.
+    - lockdep: Fix upper limit for LOCKDEP_*_BITS configs
+    - x86/amd_nb: Restrict init function to AMD-based systems
+    - tun: fix group permission check
+    - mmc: core: Respect quirk_max_rate for non-UHS SDIO card
+    - mfd: lpc_ich: Add another Gemini Lake ISA bridge PCI device-id
+    - HID: Wacom: Add PCI Wacom device support
+    - net/mlx5: use do_aux_work for PHC overflow checks
+    - wifi: iwlwifi: avoid memory leak
+    - i2c: Force ELAN06FA touchpad I2C bus freq to 100KHz
+    - APEI: GHES: Have GHES honor the panic= setting
+    - net: wwan: iosm: Fix hibernation by re-binding the driver around it
+    - mmc: sdhci-msm: Correctly set the load for the regulator
+    - tipc: re-order conditions in tipc_crypto_key_rcv()
+    - selftests/net/ipsec: Fix Null pointer dereference in rtattr_pack()
+    - Input: allocate keycode for phone linking
+    - platform/x86: acer-wmi: Ignore AC events
+    - x86/mm: Don't disable PCID when INVLPG has been fixed by microcode
+    - usb: chipidea: ci_hdrc_imx: use dev_err_probe()
+    - usb: chipidea/ci_hdrc_imx: Convert to platform remove callback returning
+      void
+    - usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in
+      the error path of .probe()
+    - net/ncsi: Add NC-SI 1.2 Get MC MAC Address command
+    - net/ncsi: fix locking in Get MAC Address handling
+    - xfs: report realtime block quota limits on realtime directories
+    - xfs: don't over-report free space or inodes in statvfs
+    - usb: xhci: Add timeout argument in address_device USB HCD callback
+    - nvme: handle connectivity loss in nvme_set_queue_count
+    - firmware: iscsi_ibft: fix ISCSI_IBFT Kconfig entry
+    - gpu: drm_dp_cec: fix broken CEC adapter properties check
+    - tg3: Disable tg3 PCIe AER on system reboot
+    - udp: gso: do not drop small packets when PMTU reduces
+    - gpio: pca953x: Improve interrupt support
+    - net: atlantic: fix warning during hot unplug
+    - x86/xen: fix xen_hypercall_hvm() to not clobber %rbx
+    - x86/xen: add FRAME_END to xen_hypercall_hvm()
+    - tun: revert fix group permission check
+    - cpufreq: s3c64xx: Fix compilation warning
+    - leds: lp8860: Write full EEPROM, not only half of it
+    - drm/modeset: Handle tiled displays in pan_display_atomic.
+    - s390/futex: Fix FUTEX_OP_ANDN implementation
+    - m68k: vga: Fix I/O defines
+    - arm64: dts: rockchip: increase gmac rx_delay on rk3399-puma
+    - KVM: s390: vsie: fix some corner-cases when grabbing vsie pages
+    - drm/amd/pm: Mark MM activity as unsupported
+    - drm/komeda: Add check for komeda_get_layer_fourcc_list()
+    - drm/i915: Drop 64bpp YUV formats from ICL+ SDR planes
+    - Bluetooth: L2CAP: accept zero as a special value for MTU auto-selection
+    - clk: sunxi-ng: a100: enable MMC clock reparenting
+    - clk: qcom: clk-alpha-pll: fix alpha mode configuration
+    - clk: qcom: gcc-mdm9607: Fix cmd_rcgr offset for blsp1_uart6 rcg
+    - clk: qcom: clk-rpmh: prevent integer overflow in recalc_rate
+    - efi: libstub: Use '-std=gnu11' to fix build with GCC 15
+    - perf bench: Fix undefined behavior in cmpworker()
+    - of: Correct child specifier used as input of the 2nd nexus node
+    - of: Fix of_find_node_opts_by_path() handling of alias+path+options
+    - of: reserved-memory: Fix using wrong number of cells to get property
+      'alignment'
+    - HID: hid-sensor-hub: don't use stale platform-data on remove
+    - wifi: rtlwifi: rtl8821ae: Fix media status report
+    - usb: gadget: f_tcm: Translate error to sense
+    - usb: gadget: f_tcm: Decrement command ref count on cleanup
+    - usb: gadget: f_tcm: ep_autoconfig with fullspeed endpoint
+    - usb: gadget: f_tcm: Don't prepare BOT write request twice
+    - serial: sh-sci: Drop __initdata macro for port_cfg
+    - serial: sh-sci: Do not probe the serial port if its slot in sci_ports[] is
+      in use
+    - MIPS: Loongson64: remove ROM Size unit in boardinfo
+    - powerpc/pseries/eeh: Fix get PE state translation
+    - dm-crypt: don't update io->sector after kcryptd_crypt_write_io_submit()
+    - dm-crypt: track tag_offset in convert_context
+    - mips/math-emu: fix emulation of the prefx instruction
+    - ALSA: hda/realtek: Enable headset mic on Positivo C6400
+    - PCI: endpoint: Finish virtual EP removal in pci_epf_remove_vepf()
+    - nvme-pci: Add TUXEDO InfinityFlex to Samsung sleep quirk
+    - nvme-pci: Add TUXEDO IBP Gen9 to Samsung sleep quirk
+    - scsi: qla2xxx: Move FCE Trace buffer allocation to user control
+    - scsi: storvsc: Set correct data length for sending SCSI command without
+      payload
+    - kbuild: Move -Wenum-enum-conversion to W=2
+    - x86/boot: Use '-std=gnu11' to fix build with GCC 15
+    - arm64: dts: qcom: sm8350: Fix MPSS memory length
+    - crypto: qce - fix priority to be less than ARMv8 CE
+    - xfs: Add error handling for xfs_reflink_cancel_cow_range
+    - media: ccs: Clean up parsed CCS static data on parse failure
+    - iio: light: as73211: fix channel handling in only-color triggered buffer
+    - soc: qcom: smem_state: fix missing of_node_put in error path
+    - media: mc: fix endpoint iteration
+    - media: ov5640: fix get_light_freq on auto
+    - media: ccs: Fix CCS static data parsing for large block sizes
+    - media: ccs: Fix cleanup order in ccs_probe()
+    - media: uvcvideo: Fix event flags in uvc_ctrl_send_events
+    - media: uvcvideo: Remove redundant NULL assignment
+    - crypto: qce - fix goto jump in error path
+    - crypto: qce - unregister previously registered algos in error path
+    - nvmem: qcom-spmi-sdam: Set size in struct nvmem_config
+    - nvmem: core: improve range check for nvmem_cell_write()
+    - vfio/platform: check the bounds of read/write syscalls
+    - pnfs/flexfiles: retry getting layout segment for reads
+    - ocfs2: fix incorrect CPU endianness conversion causing mount failure
+    - mtd: onenand: Fix uninitialized retlen in do_otp_read()
+    - misc: fastrpc: Fix registered buffer page address
+    - net/ncsi: wait for the last response to Deselect Package before configuring
+      channel
+    - net: phy: c45-tjaxx: add delay between MDIO write and read in soft_reset
+    - MIPS: ftrace: Declare ftrace_get_parent_ra_addr() as static
+    - net/ncsi: use dev_set_mac_address() for Get MC MAC Address handling
+    - gpio: xilinx: remove excess kernel doc
+    - memory: tegra20-emc: Correct memory device mask
+    - ocfs2: check dir i_size in ocfs2_find_entry
+    - mptcp: prevent excessive coalescing on receive
+    - ndisc: ndisc_send_redirect() must use dev_get_by_index_rcu()
+    - drm/i915/selftests: avoid using uninitialized context
+    - gpio: bcm-kona: Fix GPIO lock/unlock for banks above bank 0
+    - gpio: bcm-kona: Make sure GPIO bits are unlocked when requesting IRQ
+    - gpio: bcm-kona: Add missing newline to dev_err format string
+    - xen: remove a confusing comment on auto-translated guest I/O
+    - x86/xen: allow larger contiguous memory regions in PV guests
+    - media: cxd2841er: fix 64-bit division on gcc-9
+    - PCI/DPC: Quirk PIO log size for Intel Raptor Lake-P
+    - vfio/pci: Enable iowrite64 and ioread64 for vfio pci
+    - Grab mm lock before grabbing pt lock
+    - x86/mm/tlb: Only trim the mm_cpumask once a second
+    - ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet 5V
+    - batman-adv: Ignore neighbor throughput metrics in error case
+    - perf/x86/intel: Ensure LBRs are disabled when a CPU is starting
+    - usb: roles: set switch registered flag early on
+    - usb: gadget: udc: renesas_usb3: Fix compiler warning
+    - usb: dwc2: gadget: remove of_node reference upon udc_stop
+    - USB: pci-quirks: Fix HCCPARAMS register error for LS7A EHCI
+    - usb: core: fix pipe creation for get_bMaxPacketSize0
+    - USB: quirks: add USB_QUIRK_NO_LPM quirk for Teclast dist
+    - USB: Add USB_QUIRK_NO_LPM quirk for sony xperia xz1 smartphone
+    - USB: cdc-acm: Fill in Renesas R-Car D3 USB Download mode quirk
+    - usb: cdc-acm: Fix handling of oversized fragments
+    - USB: serial: option: add MeiG Smart SLM828
+    - USB: serial: option: add Telit Cinterion FN990B compositions
+    - USB: serial: option: fix Telit Cinterion FN990A name
+    - USB: serial: option: drop MeiG Smart defines
+    - can: c_can: fix unbalanced runtime PM disable in error path
+    - can: j1939: j1939_sk_send_loop(): fix unable to send messages with data
+      length zero
+    - alpha: make stack 16-byte aligned (most cases)
+    - efi: Avoid cold plugged memory for placing the kernel
+    - cgroup: fix race between fork and cgroup.kill
+    - serial: 8250: Fix fifo underflow on flush
+    - alpha: align stack for page fault and user unaligned trap handlers
+    - gpio: stmpe: Check return value of stmpe_reg_read in
+      stmpe_gpio_irq_sync_unlock
+    - regmap-irq: Add missing kfree()
+    - arm64: Handle .ARM.attributes section in linker scripts
+    - mlxsw: Add return value check for mlxsw_sp_port_get_stats_raw()
+    - btrfs: fix hole expansion when writing at an offset beyond EOF
+    - clocksource: Replace cpumask_weight() with cpumask_empty()
+    - clocksource: Use pr_info() for "Checking clocksource synchronization"
+      message
+    - ipv4: add RCU protection to ip4_dst_hoplimit()
+    - net: treat possible_net_t net pointer as an RCU one and add read_pnet_rcu()
+    - net: add dev_net_rcu() helper
+    - ipv4: use RCU protection in rt_is_expired()
+    - ipv4: use RCU protection in inet_select_addr()
+    - Namespaceify min_pmtu sysctl
+    - Namespaceify mtu_expires sysctl
+    - selftest: net: Test IPv4 PMTU exceptions with DSCP and ECN
+    - net: ipv4: Cache pmtu for all packet paths if multipath enabled
+    - neighbour: delete redundant judgment statements
+    - drm/tidss: Fix issue in irq handling causing irq-flood issue
+    - drm/tidss: Clear the interrupt status for interrupts being disabled
+    - kdb: Do not assume write() callback available
+    - alpha: replace hardcoded stack offsets with autogenerated ones
+    - nilfs2: do not output warnings when clearing dirty buffers
+    - can: ems_pci: move ASIX AX99100 ids to pci_ids.h
+    - serial: 8250_pci: add support for ASIX AX99100
+    - parport_pc: add support for ASIX AX99100
+    - netdevsim: print human readable IP address
+    - selftests: rtnetlink: update netdevsim ipsec output format
+    - ARM: dts: dra7: Add bus_dma_limit for l4 cfg bus
+    - x86/i8253: Disable PIT timer 0 when not in use
+    - Revert "btrfs: avoid monopolizing a core when activating a swap file"
+    - btrfs: avoid monopolizing a core when activating a swap file
+    - arm64: mte: Do not allow PROT_MTE on MAP_HUGETLB user mappings
+    - crypto: testmgr - fix wrong key length for pkcs1pad
+    - crypto: testmgr - Fix wrong test case of RSA
+    - crypto: testmgr - fix version number of RSA tests
+    - crypto: testmgr - populate RSA CRT parameters in RSA test vectors
+    - crypto: testmgr - some more fixes to RSA test vectors
+    - mm: update mark_victim tracepoints fields
+    - drm/probe-helper: Create a HPD IRQ event helper for a single connector
+    - drm/rockchip: cdn-dp: Use drm_connector_helper_hpd_irq_event()
+    - ASoC: renesas: rz-ssi: Add a check for negative sample_space
+    - arm64: dts: mediatek: mt8183: Disable DSI display output by default
+    - tpm: Use managed allocation for bios event log
+    - kfence: allow use of a deferrable timer
+    - [Config] updateconfigs to disable new KFENCE_DEFERRABLE
+    - kfence: enable check kfence canary on panic via boot param
+    - kfence: skip __GFP_THISNODE allocations on NUMA systems
+    - soc: mediatek: mtk-devapc: Switch to devm_clk_get_enabled()
+    - soc: mediatek: mtk-devapc: Fix leaking IO map on error paths
+    - soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
+    - soc: mediatek: mtk-devapc: Fix leaking IO map on driver remove
+    - media: uvcvideo: Set error_idx during ctrl_commit errors
+    - media: uvcvideo: Refactor iterators
+    - media: uvcvideo: Only save async fh if success
+    - batman-adv: Drop initialization of flexible ethtool_link_ksettings
+    - usb: dwc3: Increase DWC3 controller halt timeout
+    - usb: dwc3: Fix timeout issue during controller enter/exit from halt state
+    - powerpc/64s/mm: Move __real_pte stubs into hash-4k.h
+    - powerpc/64s: Rewrite __real_pte() and __rpte_to_hidx() as static inline
+    - ALSA: hda/realtek: Fixup ALC225 depop procedure
+    - geneve: Suppress list corruption splat in geneve_destroy_tunnels().
+    - net: extract port range fields from fl_flow_key
+    - flow_dissector: Fix handling of mixed port and port-range keys
+    - flow_dissector: Fix port range key handling in BPF conversion
+    - net: Add non-RCU dev_getbyhwaddr() helper
+    - arp: switch to dev_getbyhwaddr() in arp_req_set_public()
+    - power: supply: da9150-fg: fix potential overflow
+    - nvme/ioctl: add missing space in err message
+    - bpf: skip non exist keys in generic_map_lookup_batch
+    - ALSA: hda/conexant: Add quirk for HP ProBook 450 G4 mute LED
+    - acct: block access to kernel internal filesystems
+    - mtd: rawnand: cadence: fix error code in cadence_nand_init()
+    - mtd: rawnand: cadence: use dma_map_resource for sdma address
+    - mtd: rawnand: cadence: fix incorrect device in dma_unmap_single
+    - x86/cpu/kvm: SRSO: Fix possible missing IBPB on VM-Exit
+    - IB/mlx5: Set and get correct qp_num for a DCT QP
+    - ovl: use wrappers to all vfs_*xattr() calls
+    - ovl: pass ofs to creation operations
+    - scsi: core: Don't memset() the entire scsi_cmnd in scsi_init_command()
+    - scsi: core: Clear driver private data when retrying request
+    - RDMA/mlx5: Fix bind QP error cleanup flow
+    - sunrpc: suppress warnings for unused procfs functions
+    - ALSA: usb-audio: Avoid dropping MIDI events at closing multiple ports
+    - Bluetooth: L2CAP: Fix L2CAP_ECRED_CONN_RSP response
+    - afs: remove variable nr_servers
+    - afs: Make it possible to find the volumes that are using a server
+    - afs: Fix the server_list to unuse a displaced server rather than putting it
+    - net: loopback: Avoid sending IP packets without an Ethernet header
+    - net: cadence: macb: Synchronize stats calculations
+    - ASoC: es8328: fix route from DAC to output
+    - ipvs: Always clear ipvs_property flag in skb_scrub_packet()
+    - tcp: Defer ts_recent changes until req is owned
+    - net: mvpp2: cls: Fixed Non IP flow, with vlan tag flow defination.
+    - net/mlx5: IRQ, Fix null string in debug print
+    - seg6: add support for SRv6 H.Encaps.Red behavior
+    - seg6: add support for SRv6 H.L2Encaps.Red behavior
+    - include: net: add static inline dst_dev_overhead() to dst.h
+    - net: ipv6: seg6_iptunnel: mitigate 2-realloc issue
+    - net: ipv6: fix dst ref loop on input in seg6 lwt
+    - net: ipv6: rpl_iptunnel: mitigate 2-realloc issue
+    - net: ipv6: fix dst ref loop on input in rpl lwt
+    - x86/CPU: Fix warm boot hang regression on AMD SC1100 SoC systems
+    - ftrace: Avoid potential division by zero in function_stat_show()
+    - ALSA: usb-audio: Re-add sample rate quirk for Pioneer DJM-900NXS2
+    - perf/core: Fix low freq setting via IOC_PERIOD
+    - drm/amd/display: Fix HPD after gpu reset
+    - net: enetc: fix the off-by-one issue in enetc_map_tx_buffs()
+    - net: enetc: update UDP checksum when updating originTimestamp field
+    - net: enetc: correct the xdp_tx statistics
+    - phy: tegra: xusb: reset VBUS & ID OVERRIDE
+    - phy: exynos5-usbdrd: fix MPLL_MULTIPLIER and SSC_REFCLKSEL masks in refclk
+    - vmlinux.lds: Ensure that const vars with relocations are mapped R/O
+    - intel_idle: Handle older CPUs, which stop the TSC in deeper C states,
+      correctly
+    - drm/amdgpu: Check extended configuration space register when system uses
+      large bar
+    - drm/amdgpu: disable BAR resize on Dell G5 SE
+    - Revert "of: reserved-memory: Fix using wrong number of cells to get property
+      'alignment'"
+    - HID: appleir: Fix potential NULL dereference at raw event handle
+    - gpio: rcar: Use raw_spinlock to protect register access
+    - gpio: aggregator: protect driver attr handlers against module unload
+    - ALSA: hda: intel: Add Dell ALC3271 to power_save denylist
+    - ALSA: hda/realtek: update ALC222 depop optimize
+    - drm/radeon: Fix rs400_gpu_init for ATI mobility radeon Xpress 200M
+    - platform/x86: thinkpad_acpi: Add battery quirk for ThinkPad X131e
+    - x86/cacheinfo: Validate CPUID leaf 0x2 EDX output
+    - x86/cpu: Validate CPUID leaf 0x2 EDX output
+    - x86/cpu: Properly parse CPUID leaf 0x2 TLB descriptor 0x63
+    - wifi: cfg80211: regulatory: improve invalid hints checking
+    - wifi: nl80211: reject cooked mode if it is set along with other flags
+    - rapidio: add check for rio_add_net() in rio_scan_alloc_net()
+    - rapidio: fix an API misues when rio_add_net() fails
+    - s390/traps: Fix test_monitor_call() inline assembly
+    - block: fix conversion of GPT partition name to 7-bit
+    - mm/page_alloc: fix uninitialized variable
+    - mm: don't skip arch_sync_kernel_mappings() in error paths
+    - wifi: iwlwifi: limit printed string from FW file
+    - HID: google: fix unused variable warning under !CONFIG_ACPI
+    - HID: intel-ish-hid: Fix use-after-free issue in ishtp_hid_remove()
+    - nvmet-tcp: Fix a possible sporadic response drops in weakly ordered arch
+    - net: gso: fix ownership in __udp_gso_segment
+    - caif_virtio: fix wrong pointer check in cfv_probe()
+    - hwmon: (pmbus) Initialise page count in pmbus_identify()
+    - hwmon: (ntc_thermistor) Fix the ncpXXxh103 sensor table
+    - hwmon: (ad7314) Validate leading zero bits and return error
+    - ALSA: usx2y: validate nrpacks module parameter on probe
+    - llc: do not use skb_get() before dev_queue_xmit()
+    - hwmon: fix a NULL vs IS_ERR_OR_NULL() check in xgene_hwmon_probe()
+    - drm/sched: Fix preprocessor guard
+    - be2net: fix sleeping while atomic bugs in be_ndo_bridge_getlink
+    - net: hns3: make sure ptp clock is unregister and freed if
+      hclge_ptp_get_cycle returns an error
+    - ppp: Fix KMSAN uninit-value warning with bpf
+    - vlan: enforce underlying device type
+    - x86/sgx: Support loading enclave page without VMA permissions check
+    - x86/sgx: Move PTE zap code to new sgx_zap_enclave_ptes()
+    - x86/sgx: Export sgx_encl_{grow,shrink}()
+    - x86/sgx: Support VA page allocation without reclaiming
+    - x86/sgx: Fix size overflows in sgx_encl_create()
+    - exfat: fix soft lockup in exfat_clear_bitmap
+    - net-timestamp: support TCP GSO case for a few missing flags
+    - sched/fair: Fix potential memory corruption in child_cfs_rq_on_list
+    - net: ipv6: fix dst ref loop in ila lwtunnel
+    - net: ipv6: fix missing dst ref drop in ila lwtunnel
+    - gpio: rcar: Fix missing of_node_put() call
+    - Revert "drivers/card_reader/rtsx_usb: Restore interrupt based detection"
+    - usb: renesas_usbhs: Call clk_put()
+    - usb: renesas_usbhs: Use devm_usb_get_phy()
+    - usb: hub: lack of clearing xHC resources
+    - usb: quirks: Add DELAY_INIT and NO_LPM for Prolific Mass Storage Card Reader
+    - usb: renesas_usbhs: Flush the notify_hotplug_work
+    - usb: atm: cxacru: fix a flaw in existing endpoint checks
+    - usb: dwc3: Set SUSPENDENABLE soon after phy init
+    - usb: dwc3: gadget: Prevent irq storm when TH re-executes
+    - usb: typec: ucsi: increase timeout for PPM reset operations
+    - usb: typec: tcpci_rt1711h: Unmask alert interrupts to fix functionality
+    - usb: gadget: Set self-powered based on MaxPower and bmAttributes
+    - usb: gadget: Fix setting self-powered state on suspend
+    - usb: gadget: Check bmAttributes only if configuration is valid
+    - xhci: pci: Fix indentation in the PCI device ID definitions
+    - usb: xhci: Enable the TRB overfetch quirk on VIA VL805
+    - mei: me: add panther lake P DID
+    - intel_th: pci: Add Arrow Lake support
+    - intel_th: pci: Add Panther Lake-H support
+    - intel_th: pci: Add Panther Lake-P/U support
+    - slimbus: messaging: Free transaction ID in delayed interrupt scenario
+    - bus: mhi: host: pci_generic: Use pci_try_reset_function() to avoid deadlock
+    - eeprom: digsy_mtc: Make GPIO lookup table match the device
+    - drivers: virt: acrn: hsm: Use kzalloc to avoid info leak in pmcmd_ioctl
+    - media: uvcvideo: Avoid invalid memory access
+    - media: uvcvideo: Avoid returning invalid controls
+    - md: select BLOCK_LEGACY_AUTOLOAD
+    - [Config] updateconfigs to select BLOCK_LEGACY_AUTOLOAD
+    - mtd: rawnand: cadence: fix unchecked dereference
+    - spi-mxs: Fix chipselect glitch
+    - nilfs2: move page release outside of nilfs_delete_entry and nilfs_set_link
+    - nilfs2: eliminate staggered calls to kunmap in nilfs_rename
+    - bpf, vsock: Invoke proto::close on close()
+    - kbuild: userprogs: use correct lld when linking through clang
+    - net: ipv6: fix dst refleaks in rpl, seg6 and ioam6 lwtunnels
+    - Linux 5.15.179
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21647
+    - sched: sch_cake: add bounds checks to host bulk flow fairness counts
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58002
+    - media: uvcvideo: Remove dangling pointers
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58079
+    - media: uvcvideo: Fix crash during unbind if gpio unit is in use
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21721
+    - nilfs2: handle errors that nilfs_prepare_chunk() may return
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-26982
+    - Squashfs: check the inode number is not the invalid value of zero
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21844
+    - smb: client: Add check for next_buffer in receive_encrypted_standard()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58090
+    - sched/core: Prevent rescheduling when interrupts are disabled
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21875
+    - mptcp: always handle address removal under msk socket lock
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21877
+    - usbnet: gl620a: fix endpoint checking in genelink_bind()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21878
+    - i2c: npcm: disable interrupt enable bit before devm_request_irq
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21887
+    - ovl: fix UAF in ovl_dentry_update_reval by moving dput() in ovl_link_up
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21846
+    - acct: perform last write from workqueue
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21848
+    - nfp: bpf: Add check for nfp_app_ctrl_msg_alloc()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21862
+    - drop_monitor: fix incorrect initialization order
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21871
+    - tee: optee: Fix supplicant wait loop
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21865
+    - gtp: Suppress list corruption splat in gtp_net_exit_batch_rtnl().
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21858
+    - geneve: Fix use-after-free in geneve_find_dev().
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21866
+    - powerpc/code-patching: Fix KASAN hit by not flagging text patching area as
+      VM_ALLOC
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21859
+    - USB: gadget: f_midi: f_midi_complete to call queue_work
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21823
+    - batman-adv: Drop unmanaged ELP metric worker
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58005
+    - tpm: Change to kvalloc() in eventlog/acpi.c
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21748
+    - ksmbd: fix integer overflows on 32 bit systems
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57977
+    - memcg: fix soft lockup in the OOM process
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57978
+    - media: imx-jpeg: Fix potential error pointer dereference in detach_pm()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57979
+    - pps: Fix a use-after-free
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-47726
+    - f2fs: fix to wait dio completion
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21811
+    - nilfs2: protect access to buffers with no active references
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21722
+    - nilfs2: do not force clear folio if buffer is referenced
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58086
+    - drm/v3d: Stop active perfmon if it is being destroyed
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21758
+    - ipv6: mcast: add RCU protection to mld_newpack()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21760
+    - ndisc: extend RCU protection in ndisc_send_skb()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21761
+    - openvswitch: use RCU protection in ovs_vport_cmd_fill_info()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21762
+    - arp: use RCU protection in arp_xmit()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21763
+    - neighbour: use RCU protection in __neigh_notify()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21764
+    - ndisc: use RCU protection in ndisc_alloc_skb()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21765
+    - ipv6: use RCU protection in ip6_default_advmss()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21766
+    - ipv4: use RCU protection in __ip_rt_update_pmtu()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21767
+    - clocksource: Use migrate_disable() to avoid calling get_random_u32() in
+      atomic context
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21772
+    - partitions: mac: fix handling of bogus partition table
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21704
+    - usb: cdc-acm: Check control transfer buffer size before access
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21776
+    - USB: hub: Ignore non-compliant devices with too many configs or interfaces
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21835
+    - usb: gadget: f_midi: fix MIDI Streaming descriptor lengths
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21779
+    - KVM: x86: Reject Hyper-V's SEND_IPI hypercalls if local APIC isn't in-kernel
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21781
+    - batman-adv: fix panic during interface removal
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21782
+    - orangefs: fix a oob in orangefs_debug_write
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57834
+    - media: vidtv: Fix a null-ptr-deref in vidtv_mux_stop_thread
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21785
+    - arm64: cacheinfo: Avoid out-of-bounds write to cacheinfo array
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21787
+    - team: better TEAM_OPTION_TYPE_STRING validation
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21791
+    - vrf: use RCU protection in l3mdev_l3_out()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58020
+    - HID: multitouch: Add NULL check in mt_input_configured
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21795
+    - NFSD: fix hang in nfsd4_shutdown_callback
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21796
+    - nfsd: clear acl_access/acl_default after releasing them
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21820
+    - tty: xilinx_uartps: split sysrq handling
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21814
+    - ptp: Ensure info->enable callback is always set
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21735
+    - NFC: nci: Add bounds checking in nci_hci_create_pipe()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21736
+    - nilfs2: fix possible int overflows in nilfs_fiemap()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58001
+    - ocfs2: handle a symlink read error correctly
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58007
+    - soc: qcom: socinfo: Avoid out of bounds read of serial number
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21744
+    - wifi: brcmfmac: fix NULL pointer dereference in brcmf_txfinalize()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21745
+    - blk-cgroup: Fix class @block_class's subsystem refcount leakage
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58076
+    - clk: qcom: gcc-sm6350: Add missing parent_map for two clocks
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58083
+    - KVM: Explicitly verify target vCPU is online in kvm_get_vcpu()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58010
+    - binfmt_flat: Fix integer overflow bug on 32 bit systems
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21749
+    - net: rose: lock the socket in rose_bind()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57981
+    - usb: xhci: Fix NULL pointer dereference on certain command aborts
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21684
+    - gpio: xilinx: Convert gpio_lock to raw spinlock
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58085
+    - tomoyo: don't emit warning in tomoyo_write_control()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58014
+    - wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58016
+    - safesetid: check size of policy writes
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58017
+    - printk: Fix signed integer overflow when defining LOG_BUF_LEN_MAX
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21753
+    - btrfs: fix use-after-free when attempting to join an aborted transaction
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58055
+    - usb: gadget: f_tcm: Don't free command immediately
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57980
+    - media: uvcvideo: Fix double free in error path
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21707
+    - mptcp: consolidate suboption status
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21708
+    - net: usb: rtl8150: enable basic endpoint checking
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21826
+    - netfilter: nf_tables: reject mismatching sum of field_len with set key
+      length
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21715
+    - net: davicom: fix UAF in dm9000_drv_remove
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21718
+    - net: rose: fix timer races against user threads
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21719
+    - ipmr: do not call mr_mfc_uses_dev() for unres entries
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21802
+    - net: hns3: fix oops when unload drivers paralleling
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58058
+    - ubifs: skip dumping tnc tree when zroot is null
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58069
+    - rtc: pcf85063: fix potential OOB write in PCF85063 NVMEM read
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21804
+    - PCI: rcar-ep: Fix incorrect variable used when calling
+      devm_request_mem_region()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58034
+    - memory: tegra20-emc: fix an OF node reference bug in
+      tegra_emc_find_node_by_ram_code()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57973
+    - rdma/cxgb4: Prevent potential integer overflow on 32bit
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21726
+    - padata: avoid UAF for reorder_work
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21727
+    - padata: fix UAF in padata_reorder
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21728
+    - bpf: Send signals asynchronously if !preemptible
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21711
+    - net/rose: prevent integer overflows in rose_setsockopt()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21799
+    - net: ethernet: ti: am65-cpsw: fix freeing IRQ in
+      am65_cpsw_nuss_remove_tx_chns()
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21806
+    - net: let net.core.dev_weight always be non-zero
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21830
+    - landlock: Handle weird files
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58071
+    - team: prevent adding a device which is already a team device lower
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58063
+    - wifi: rtlwifi: fix memory leaks and invalid access at probe error path
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58072
+    - wifi: rtlwifi: remove unused check_buddy_priv
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58051
+    - ipmi: ipmb: Add check devm_kasprintf() returned value
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-58052
+    - drm/amdgpu: Fix potential NULL pointer dereference in
+      atomctrl_get_smc_sclk_range_table
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2024-57986
+    - HID: core: Fix assumption that Resolution Multipliers must be in Logical
+      Collections
+  * Jammy update: v5.15.179 upstream stable release (LP: #2106026) //
+    CVE-2025-21731
+    - nbd: don't allow reconnect after disconnect
+  * Fix bugs preventing boot on Intel TDX-enabled hosts (LP: #2097811)
+    - x86/mtrr: Remove physical address size calculation
+  * Build failure when CONFIG_NET_SWITCHDEV=n due to CVE-2024-26837 fix backport
+    (LP: #2104380)
+    - SAUCE: net: switchdev: fix compilation error for CONFIG_NET_SWITCHDEV=n
+  * nfsd hangs and never recovers after NFS4ERR_DELAY and a connection loss
+    (LP: #2103564)
+    - NFSD: Reset cb_seq_status after NFS4ERR_DELAY
+  * kernel hard lockup in cgroups during eBPF workload (LP: #2089318)
+    - cgroup: cgroup: Honor caller's cgroup NS when resolving cgroup id
+    - cgroup: Homogenize cgroup_get_from_id() return value
+    - cgroup: Make cgroup_get_from_id() prettier
+    - cgroup.c: add helper __cset_cgroup_from_root to cleanup duplicated codes
+    - cgroup: Reorganize css_set_lock and kernfs path processing
+  * CVE-2023-52664
+    - net: atlantic: eliminate double free in error handling logic
+  * CVE-2023-52927
+    - netfilter: allow exp not to be removed in nf_ct_find_expectation
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 25 Apr 2025 18:27:55 +0800
+
+linux-xilinx-zynqmp (5.15.0-1046.50) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1046.50 -proposed tracker (LP: #2102584)
+
+  [ Ubuntu: 5.15.0-138.148 ]
+
+  * jammy/linux: 5.15.0-138.148 -proposed tracker (LP: #2102587)
+  * ipsec_offload in rtnetlink.sh from ubunsu_kselftests_net fails on O/J
+    (LP: #2096976)
+    - SAUCE: selftest: netfilter: fix null IP field in kci_test_ipsec_offload
+  * CVE-2025-21756
+    - vsock: Keep the binding until socket destruction
+    - vsock: Orphan socket after transport release
+  * CVE-2024-50256
+    - netfilter: nf_reject_ipv6: fix potential crash in nf_send_reset6()
+  * CVE-2025-21702
+    - pfifo_tail_enqueue: Drop new packet when sch->limit == 0
+  * CVE-2025-21703
+    - netem: Update sch->q.qlen before qdisc_tree_reduce_backlog()
+  * CVE-2025-21700
+    - net: sched: Disallow replacing of child qdisc from one parent to another
+  * CVE-2024-46826
+    - ELF: fix kernel.randomize_va_space double read
+  * CVE-2024-56651
+    - can: hi311x: hi3110_can_ist(): fix potential use-after-free
+  * iBFT iSCSI out-of-bounds shift UBSAN warning (LP: #2097824)
+    - iscsi_ibft: Fix UBSAN shift-out-of-bounds warning in ibft_attr_show_nic()
+  * CVE-2024-50248
+    - ntfs3: Add bounds checking to mi_enum_attr()
+    - fs/ntfs3: Sequential field availability check in mi_enum_attr()
+  * CVE-2022-0995
+    - watch_queue: Use the bitmap API when applicable
+  * CVE-2024-26837
+    - net: bridge: switchdev: Skip MDB replays of deferred events on offload
+  * CVE-2025-21701
+    - net: avoid race between device unregistration and ethnl ops
+  * CVE-2024-57798
+    - drm/dp_mst: Skip CSN if topology probing is not done yet
+    - drm/dp_mst: Ensure mst_primary pointer is valid in
+      drm_dp_mst_handle_up_req()
+  * CVE-2024-56658
+    - net: defer final 'struct net' free in netns dismantle
+  * CVE-2024-35864
+    - smb: client: fix potential UAF in smb2_is_valid_lease_break()
+  * CVE-2024-35864/CVE-2024-26928
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Thu, 27 Mar 2025 15:13:26 +0800
+
+linux-xilinx-zynqmp (5.15.0-1045.49) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1045.49 -proposed tracker (LP: #2102426)
+
+  [ Ubuntu: 5.15.0-136.147 ]
+
+  * jammy/linux: 5.15.0-136.147 -proposed tracker (LP: #2102429)
+  * CVE-2024-57798
+    - drm/dp_mst: Skip CSN if topology probing is not done yet
+    - drm/dp_mst: Ensure mst_primary pointer is valid in
+      drm_dp_mst_handle_up_req()
+  * CVE-2024-56658
+    - net: defer final 'struct net' free in netns dismantle
+  * CVE-2024-35864
+    - smb: client: fix potential UAF in smb2_is_valid_lease_break()
+  * CVE-2024-35864/CVE-2024-26928
+    - smb: client: fix potential UAF in cifs_debug_files_proc_show()
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Wed, 19 Mar 2025 15:34:32 +0800
+
+linux-xilinx-zynqmp (5.15.0-1044.48) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1044.48 -proposed tracker (LP: #2098297)
+
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283)
+    - [Config] Set CONFIG_ARM_TIMER_SP804 as 'n'
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.zynqmp/dkms-versions -- update from kernel-versions
+      (main/2025.02.10)
+
+  [ Ubuntu: 5.15.0-135.146 ]
+
+  * jammy/linux: 5.15.0-135.146 -proposed tracker (LP: #2098300)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.02.10)
+  * Jammy update: v5.15.178 upstream stable release (LP: #2098441)
+    - ASoC: wm8994: Add depends on MFD core
+    - ASoC: samsung: Add missing selects for MFD_WM8994
+    - seccomp: Stub for !CONFIG_SECCOMP
+    - scsi: iscsi: Fix redundant response for ISCSI_UEVENT_GET_HOST_STATS request
+    - irqchip/sunxi-nmi: Add missing SKIP_WAKE flag
+    - ASoC: samsung: Add missing depends on I2C
+    - regmap: detach regmap from dev on regmap_exit
+    - mptcp: don't always assume copied data in mptcp_cleanup_rbuf()
+    - gfs2: Truncate address space when flipping GFS2_DIF_JDATA flag
+    - net: sched: fix ets qdisc OOB Indexing
+    - vfio/platform: check the bounds of read/write syscalls
+    - fs/ntfs3: Additional check in ntfs_file_release
+    - platform/chrome: cros_ec_typec: Check for EC driver
+    - ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_find()
+    - scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
+    - wifi: iwlwifi: add a few rate index validity checks
+    - USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
+    - ALSA: usb-audio: Add delay quirk for USB Audio Device
+    - Input: atkbd - map F23 key to support default copilot shortcut
+    - Input: xpad - add unofficial Xbox 360 wireless receiver clone
+    - Input: xpad - add support for wooting two he (arm)
+    - drm/v3d: Assign job pointer to NULL before signaling the fence
+    - Linux 5.15.178
+  * CVE-2024-49925
+    - fbdev: efifb: Register sysfs groups through driver core
+  * Jammy update: v5.15.177 upstream stable release (LP: #2097298)
+    - ceph: give up on paths longer than PATH_MAX
+    - jbd2: flush filesystem device before updating tail sequence
+    - dm array: fix releasing a faulty array block twice in dm_array_cursor_end
+    - dm array: fix unreleased btree blocks on closing a faulty array cursor
+    - dm array: fix cursor index when skipping across block boundaries
+    - exfat: fix the infinite loop in exfat_readdir()
+    - exfat: fix the infinite loop in __exfat_free_cluster()
+    - ASoC: mediatek: disable buffer pre-allocation
+    - ieee802154: ca8210: Add missing check for kfifo_alloc() in ca8210_probe()
+    - net: 802: LLC+SNAP OID:PID lookup on start of skb data
+    - tcp/dccp: complete lockless accesses to sk->sk_max_ack_backlog
+    - tcp/dccp: allow a connection when sk_max_ack_backlog is zero
+    - net_sched: cls_flow: validate TCA_FLOW_RSHIFT attribute
+    - bnxt_en: Fix possible memory leak when hwrm_req_replace fails
+    - cxgb4: Avoid removal of uninserted tid
+    - tls: Fix tls_sw_sendmsg error handling
+    - netfilter: nf_tables: imbalance in flowtable binding
+    - netfilter: conntrack: clamp maximum hashtable size to INT_MAX
+    - drm/mediatek: Add support for 180-degree rotation in the display driver
+    - ksmbd: fix a missing return value check bug
+    - afs: Fix the maximum cell name length
+    - dm thin: make get_first_thin use rcu-safe list first function
+    - dm-ebs: don't set the flag DM_TARGET_PASSES_INTEGRITY
+    - sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy
+    - sctp: sysctl: rto_min/max: avoid using current->nsproxy
+    - sctp: sysctl: auth_enable: avoid using current->nsproxy
+    - sctp: sysctl: udp_port: avoid using current->nsproxy
+    - sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy
+    - drm/amd/display: Add check for granularity in dml ceil/floor helpers
+    - riscv: Fix sleeping in invalid context in die()
+    - ACPI: resource: Add TongFang GM5HG0A to irq1_edge_low_force_override[]
+    - ACPI: resource: Add Asus Vivobook X1504VAP to irq1_level_low_skip_override[]
+    - drm/amd/display: increase MAX_SURFACES to the value supported by hw
+    - scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
+    - USB: serial: option: add MeiG Smart SRM815
+    - USB: serial: option: add Neoway N723-EA support
+    - staging: iio: ad9834: Correct phase range check
+    - staging: iio: ad9832: Correct phase range check
+    - usb-storage: Add max sectors quirk for Nokia 208
+    - USB: serial: cp210x: add Phoenix Contact UPS Device
+    - usb: dwc3: gadget: fix writing NYET threshold
+    - topology: Keep the cpumask unchanged when printing cpumap
+    - USB: usblp: return error when setting unsupported protocol
+    - USB: core: Disable LPM only for non-suspended ports
+    - usb: fix reference leak in usb_new_device()
+    - usb: gadget: f_uac2: Fix incorrect setting of bNumEndpoints
+    - usb: gadget: f_fs: Remove WARN_ON in functionfs_bind
+    - iio: pressure: zpa2326: fix information leak in triggered buffer
+    - iio: dummy: iio_simply_dummy_buffer: fix information leak in triggered
+      buffer
+    - iio: light: vcnl4035: fix information leak in triggered buffer
+    - iio: imu: kmx61: fix information leak in triggered buffer
+    - iio: adc: ti-ads8688: fix information leak in triggered buffer
+    - iio: gyro: fxas21002c: Fix missing data update in trigger handler
+    - iio: adc: ti-ads124s08: Use gpiod_set_value_cansleep()
+    - iio: adc: at91: call input_free_device() on allocated iio_dev
+    - iio: inkern: call iio_device_put() only on mapped devices
+    - iio: adc: ad7124: Disable all channels at probe time
+    - block, bfq: fix waker_bfqq UAF after bfq_split_bfqq()
+    - arm64: dts: rockchip: add hevc power domain clock to rk3328
+    - of: unittest: Add bus address range parsing tests
+    - of/address: Add support for 3 address cell bus
+    - of: address: Fix address translation when address-size is greater than 2
+    - of: address: Remove duplicated functions
+    - of: address: Store number of bus flag cells rather than bool
+    - of: address: Preserve the flags portion on 1:1 dma-ranges mapping
+    - phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers
+    - phy: usb: Toggle the PHY power during init
+    - ocfs2: correct return value of ocfs2_local_free_info()
+    - ocfs2: fix slab-use-after-free due to dangling pointer dqi_priv
+    - mptcp: drop port parameter of mptcp_pm_add_addr_signal
+    - mptcp: fix TCP options overflow.
+    - phy: usb: Use slow clock for wake enabled suspend
+    - phy: usb: Fix clock imbalance for suspend/resume
+    - net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()
+    - bpf: Fix bpf_sk_select_reuseport() memory leak
+    - pktgen: Avoid out-of-bounds access in get_imix_entries
+    - net: add exit_batch_rtnl() method
+    - gtp: use exit_batch_rtnl() method
+    - gtp: Use for_each_netdev_rcu() in gtp_genl_dump_pdp().
+    - gtp: Destroy device along with udp socket's netns dismantle.
+    - nfp: bpf: prevent integer overflow in nfp_bpf_event_output()
+    - net: xilinx: axienet: Fix IRQ coalescing packet count overflow
+    - net/mlx5: Add priorities for counters in RDMA namespaces
+    - net/mlx5: Refactor mlx5_get_flow_namespace
+    - net/mlx5: Fix RDMA TX steering prio
+    - drm/v3d: Ensure job pointer is set to NULL after job completion
+    - Revert "mtd: spi-nor: core: replace dummy buswidth from addr to data"
+    - i2c: mux: demux-pinctrl: check initial mux selection, too
+    - i2c: rcar: fix NACK handling when being a target
+    - mac802154: check local interfaces before deleting sdata list
+    - hfs: Sanity check the root record
+    - fs: fix missing declaration of init_files
+    - kheaders: Ignore silly-rename files
+    - ACPI: resource: acpi_dev_irq_override(): Check DMI match last
+    - poll_wait: add mb() to fix theoretical race between waitqueue_active() and
+      .poll()
+    - nvmet: propagate npwg topology
+    - net: ethernet: xgbe: re-add aneg to supported features in PHY quirks
+    - vsock/virtio: cancel close work in the destructor
+    - vsock: reset socket state when de-assigning the transport
+    - vsock: prevent null-ptr-deref in vsock_*[has_data|has_space]
+    - filemap: avoid truncating 64-bit offset to 32 bits
+    - fs/proc: fix softlockup in __read_vmcore (part 2)
+    - gpiolib: cdev: Fix use after free in lineinfo_changed_notify
+    - irqchip/gic-v3: Handle CPU_PM_ENTER_FAILED correctly
+    - hrtimers: Handle CPU state correctly on hotplug
+    - drm/i915/fb: Relax clear color alignment to 64 bytes
+    - iio: imu: inv_icm42600: fix spi burst write not supported
+    - iio: imu: inv_icm42600: fix timestamps after suspend if sensor is on
+    - iio: adc: rockchip_saradc: fix information leak in triggered buffer
+    - Revert "drm/amdgpu: rework resume handling for display (v2)"
+    - Revert "regmap: detach regmap from dev on regmap_exit"
+    - vsock/virtio: discard packets if the transport changes
+    - ipv6: avoid possible NULL deref in rt6_uncached_list_flush_dev()
+    - nfsd: add list_head nf_gc to struct nfsd_file
+    - x86/xen: fix SLS mitigation in xen_hypercall_iret()
+    - scsi: sg: Fix slab-use-after-free read in sg_release()
+    - net: fix data-races around sk->sk_forward_alloc
+    - xhci: use pm_ptr() instead of #ifdef for CONFIG_PM conditionals
+    - Partial revert of xhci: use pm_ptr() instead #ifdef for CONFIG_PM
+      conditionals
+    - Linux 5.15.177
+  * CVE-2024-46784
+    - net: mana: Fix error handling in mana_create_txq/rxq's NAPI cleanup
+  * CVE-2024-44938
+    - jfs: Fix shift-out-of-bounds in dbDiscardAG
+  * CVE-2024-43900
+    - media: xc2028: avoid use-after-free in load_firmware_cb()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327)
+    - ALSA: usb: Fix UBSAN warning in parse_audio_unit()
+    - usb: cdns3: Add quirk flag to enable suspend residency
+    - ASoC: Intel: sof_sdw: fix jack detection on ADL-N variant RVP
+    - PCI: vmd: Create domain symlink before pci_bus_add_devices()
+    - PCI: Add ACS quirk for Broadcom BCM5760X NIC
+    - MIPS: Loongson64: DTS: Fix msi node for ls7a
+    - usb: dwc2: gadget: Don't write invalid mapped sg entries into dma_desc with
+      iommu enabled
+    - i2c: pnx: Fix timeout in wait functions
+    - erofs: fix incorrect symlink detection in fast symlink
+    - net/smc: check sndbuf_space again after NOSPACE flag is set in smc_poll
+    - ionic: use ee->offset when returning sprom data
+    - net: hinic: Fix cleanup in create_rxqs/txqs()
+    - net: ethernet: bgmac-platform: fix an OF node reference leak
+    - netfilter: ipset: Fix for recursive locking warning
+    - net: mdiobus: fix an OF node reference leak
+    - mmc: sdhci-tegra: Remove SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC quirk
+    - chelsio/chtls: prevent potential integer overflow on 32bit
+    - i2c: riic: Always round-up when calculating bus period
+    - efivarfs: Fix error on non-existent file
+    - USB: serial: option: add TCL IK512 MBIM & ECM
+    - USB: serial: option: add MeiG Smart SLM770A
+    - USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
+    - USB: serial: option: add MediaTek T7XX compositions
+    - USB: serial: option: add Telit FE910C04 rmnet compositions
+    - hwmon: (tmp513) Don't use "proxy" headers
+    - hwmon: (tmp513) Simplify with dev_err_probe()
+    - hwmon: (tmp513) Use SI constants from units.h
+    - hwmon: (tmp513) Fix interpretation of values of Shunt Voltage and Limit
+      Registers
+    - hwmon: (tmp513) Fix Current Register value interpretation
+    - hwmon: (tmp513) Fix interpretation of values of Temperature Result and Limit
+      Registers
+    - hwmon: (tmp513) Fix division of negative numbers
+    - sh: clk: Fix clk_enable() to return 0 on NULL clk
+    - zram: refuse to use zero sized block device as backing device
+    - btrfs: tree-checker: reject inline extent items with 0 ref count
+    - tracing: Fix test_event_printk() to process entire print argument
+    - tracing: Add missing helper functions in event pointer dereference check
+    - tracing: Add "%s" check in test_event_printk()
+    - NFS/pnfs: Fix a live lock between recalled layouts and layoutget
+    - of/irq: Fix using uninitialized variable @addr_len in API of_irq_parse_one()
+    - udmabuf: also check for F_SEAL_FUTURE_WRITE
+    - of: Fix error path in of_parse_phandle_with_args_map()
+    - of: Fix refcount leakage for OF node returned by __of_get_dma_parent()
+    - ceph: validate snapdirname option length when mounting
+    - epoll: Add synchronous wakeup support for ep_poll_callback
+    - drm/amdgpu: Handle NULL bo->tbo.resource (again) in amdgpu_vm_bo_update
+    - mm/vmstat: fix a W=1 clang compiler warning
+    - tcp_bpf: Charge receive socket buffer in bpf_tcp_ingress()
+    - tcp_bpf: Add sk_rmem_alloc related logic for tcp_bpf ingress redirection
+    - bpf: Check negative offsets in __bpf_skb_min_len()
+    - nfsd: restore callback functionality for NFSv4.0
+    - mtd: diskonchip: Cast an operand to prevent potential overflow
+    - mtd: rawnand: arasan: Fix double assertion of chip-select
+    - mtd: rawnand: arasan: Fix missing de-registration of NAND
+    - phy: core: Fix an OF node refcount leakage in _of_phy_get()
+    - phy: core: Fix an OF node refcount leakage in of_phy_provider_lookup()
+    - phy: core: Fix that API devm_phy_put() fails to release the phy
+    - phy: core: Fix that API devm_of_phy_provider_unregister() fails to
+      unregister the phy provider
+    - phy: core: Fix that API devm_phy_destroy() fails to destroy the phy
+    - dmaengine: mv_xor: fix child node refcount handling in early exit
+    - dmaengine: dw: Select only supported masters for ACPI devices
+    - mtd: rawnand: fix double free in atmel_pmecc_create_user()
+    - tracing/kprobe: Make trace_kprobe's module callback called after jump_label
+      update
+    - watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04
+    - scsi: qla1280: Fix hw revision numbering for ISP1020/1040
+    - ALSA: hda/conexant: fix Z60MR100 startup pop issue
+    - regmap: Use correct format specifier for logging range errors
+    - platform/x86: asus-nb-wmi: Ignore unknown event 0xCF
+    - scsi: mpt3sas: Diag-Reset when Doorbell-In-Use bit is set during driver load
+      time
+    - scsi: storvsc: Do not flag MAINTENANCE_IN return of SRB_STATUS_DATA_OVERRUN
+      as an error
+    - virtio-blk: don't keep queue frozen during system suspend
+    - vmalloc: fix accounting with i915
+    - MIPS: Probe toolchain support of -msym32
+    - arm64: mm: Rename asid2idx() to ctxid2asid()
+    - arm64: Ensure bits ASID[15:8] are masked out when the kernel uses 8-bit
+      ASIDs
+    - drm/dp_mst: Verify request type in the corresponding down message reply
+    - lib: stackinit: hide never-taken branch from compiler
+    - ksmbd: fix racy issue from session lookup and expire
+    - tracing: Constify string literal data member in struct trace_event_call
+    - btrfs: avoid monopolizing a core when activating a swap file
+    - x86/hyperv: Fix hv tsc page based sched_clock for hibernation
+    - selinux: ignore unknown extended permissions
+    - tracing: Have process_string() also allow arrays
+    - thunderbolt: Add support for Intel Raptor Lake
+    - thunderbolt: Add support for Intel Meteor Lake
+    - thunderbolt: Add Intel Barlow Ridge PCI ID
+    - thunderbolt: Add support for Intel Lunar Lake
+    - thunderbolt: Add support for Intel Panther Lake-M/P
+    - xhci: retry Stop Endpoint on buggy NEC controllers
+    - usb: xhci: Limit Stop Endpoint retries
+    - xhci: Turn NEC specific quirk for handling Stop Endpoint errors generic
+    - RDMA/mlx5: Enforce same type port association for multiport RoCE
+    - RDMA/bnxt_re: Add check for path mtu in modify_qp
+    - RDMA/bnxt_re: Fix reporting hw_ver in query_device
+    - RDMA/bnxt_re: Fix max_qp_wrs reported
+    - RDMA/bnxt_re: Fix the locking while accessing the QP table
+    - drm/bridge: adv7511_audio: Update Audio InfoFrame properly
+    - RDMA/hns: Remove redundant 'attr_mask' in modify_qp_init_to_init()
+    - RDMA/hns: Remove redundant 'bt_level' for hem_list_alloc_item()
+    - RDMA/hns: Fix mapping error of zero-hop WQE buffer
+    - RDMA/hns: Fix warning storm caused by invalid input in IO path
+    - RDMA/hns: Fix missing flush CQE for DWQE
+    - net: stmmac: platform: provide devm_stmmac_probe_config_dt()
+    - net: stmmac: don't create a MDIO bus if unnecessary
+    - net: stmmac: restructure the error path of stmmac_probe_config_dt()
+    - drm/i915/dg1: Fix power gate sequence.
+    - net: llc: reset skb->transport_header
+    - ALSA: usb-audio: US16x08: Initialize array before use
+    - eth: bcmsysport: fix call balance of priv->clk handling routines
+    - net: mv643xx_eth: fix an OF node reference leak
+    - net: wwan: iosm: Properly check for valid exec stage in ipc_mmio_init()
+    - btrfs: rename and export __btrfs_cow_block()
+    - btrfs: sysfs: convert scnprintf and snprintf to sysfs_emit
+    - btrfs: sysfs: fix direct super block member reads
+    - wifi: mac80211: wake the queues in case of failure in resume
+    - sound: usb: enable DSD output for ddHiFi TC44C
+    - sound: usb: format: don't warn that raw DSD is unsupported
+    - bpf: fix potential error return
+    - net: usb: qmi_wwan: add Telit FE910C04 compositions
+    - irqchip/gic: Correct declaration of *percpu_base pointer in union gic_base
+    - ARC: build: Try to guess GCC variant of cross compiler
+    - usb: xhci: Avoid queuing redundant Stop Endpoint commands
+    - modpost: fix input MODULE_DEVICE_TABLE() built for 64-bit on 32-bit host
+    - modpost: fix the missed iteration for the max bit in do_input()
+    - kcov: mark in_softirq_really() as __always_inline
+    - sky2: Add device ID 11ab:4373 for Marvell 88E8075
+    - net/sctp: Prevent autoclose integer overflow in sctp_association_init()
+    - drm: adv7511: Drop dsi single lane support
+    - dt-bindings: display: adi,adv7533: Drop single lane support
+    - Linux 5.15.176
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57884
+    - mm: vmscan: account for free pages to prevent infinite Loop in
+      throttle_direct_reclaim()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57889
+    - pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57890
+    - RDMA/uverbs: Prevent integer overflow issue
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57896
+    - btrfs: flush delalloc workers queue before stopping cleaner kthread during
+      unmount
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57897
+    - drm/amdkfd: Correct the migration DMA map direction
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56759
+    - btrfs: fix use-after-free when COWing tree bock and tracing is enabled
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57900
+    - ila: serialize calls to nf_register_net_hooks()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57901
+    - af_packet: fix vlan_get_protocol_dgram() vs MSG_PEEK
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57902
+    - af_packet: fix vlan_get_tci() vs MSG_PEEK
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57903
+    - net: restrict SO_REUSEPORT to inet sockets
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-36476
+    - RDMA/rtrs: Ensure 'ib_sge list' is accessible
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57802
+    - netrom: check buffer length before accessing it
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57841
+    - net: fix memory leak in tcp_conn_request()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-49998
+    - net: dsa: improve shutdown sequence
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-50121
+    - nfsd: cancel nfsd_shrinker_work using sync mode in nfs4_state_shutdown_net
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57792
+    - power: supply: gpio-charger: Fix set charge current limits
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56763
+    - tracing: Prevent bad count for tracing_cpumask_write
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56626
+    - ksmbd: fix Out-of-Bounds Write in ksmbd_vfs_stream_write
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56627
+    - ksmbd: fix Out-of-Bounds Read in ksmbd_vfs_stream_read
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56616
+    - drm/dp_mst: Fix MST sideband message body length check
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-53099
+    - bpf: Check validity of link->type in bpf_link_show_fdinfo()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57807
+    - scsi: megaraid_sas: Fix for a potential deadlock
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56767
+    - dmaengine: at_xdmac: avoid null_prt_deref in at_xdmac_prep_dma_memset
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56769
+    - media: dvb-frontends: dib3000mb: fix uninit-value in dib3000_write_reg
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-53690
+    - nilfs2: prevent use of deleted inode
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-55881
+    - KVM: x86: Play nice with protected guests in complete_hypercall_exit()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-55916
+    - Drivers: hv: util: Avoid accessing a ringbuffer not initialized yet
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56369
+    - drm/modes: Avoid divide by zero harder in drm_mode_vrefresh()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56715
+    - ionic: Fix netdev notifier unregister on failure
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-56716
+    - netdevsim: prevent bad user input in nsim_dev_health_break_write()
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-57791
+    - net/smc: check return value of sock_recvmsg when draining clc data
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-47408
+    - net/smc: check smcd_v2_ext_offset when receiving proposal msg
+  * Jammy update: v5.15.176 upstream stable release (LP: #2095327) //
+    CVE-2024-49571
+    - net/smc: check iparea_offset and ipv6_prefixes_cnt when receiving proposal
+      msg
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302)
+    - tcp: check space before adding MPTCP SYN options
+    - ALSA: usb-audio: Add implicit feedback quirk for Yamaha THR5
+    - usb: host: max3421-hcd: Correctly abort a USB request.
+    - ata: sata_highbank: fix OF node reference leak in highbank_initialize_phys()
+    - usb: dwc2: Fix HCD resume
+    - usb: dwc2: hcd: Fix GetPortStatus & SetPortFeature
+    - usb: dwc2: Fix HCD port connection race
+    - usb: ehci-hcd: fix call balance of clocks handling routines
+    - drm/i915: Fix memory leak by correcting cache object name in error handler
+    - xfs: update btree keys correctly when _insrec splits an inode root block
+    - xfs: don't drop errno values when we fail to ficlone the entire range
+    - xfs: return from xfs_symlink_verify early on V4 filesystems
+    - xfs: fix scrub tracepoints when inode-rooted btrees are involved
+    - bpf, sockmap: Fix update element with same
+    - batman-adv: Do not send uninitialized TT changes
+    - batman-adv: Remove uninitialized data in full table TT response
+    - batman-adv: Do not let TT changes list grows indefinitely
+    - tipc: fix NULL deref in cleanup_bearer()
+    - selftests: mlxsw: sharedbuffer: Remove h1 ingress test case
+    - selftests: mlxsw: sharedbuffer: Remove duplicate test cases
+    - ptp: kvm: Use decrypted memory in confidential guest on x86
+    - ptp: kvm: x86: Return EOPNOTSUPP instead of ENODEV from kvm_arch_ptp_init()
+    - net: sparx5: fix FDMA performance issue
+    - net: sparx5: fix the maximum frame length register
+    - ACPI: resource: Fix memory resource type union access
+    - cxgb4: use port number to set mac addr
+    - qca_spi: Fix clock speed for multiple QCA7000
+    - qca_spi: Make driver probing reliable
+    - Documentation: PM: Clarify pm_runtime_resume_and_get() return value
+    - bonding: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL
+    - team: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL
+    - ACPICA: events/evxfregn: don't release the ContextMutex that was never
+      acquired
+    - blk-iocost: Avoid using clamp() on inuse in __propagate_weights()
+    - tracing/kprobes: Skip symbol counting logic for module symbols in
+      create_local_trace_kprobe()
+    - xen/netfront: fix crash when removing device
+    - x86: make get_cpu_vendor() accessible from Xen code
+    - objtool/x86: allow syscall instruction
+    - x86/static-call: provide a way to do very early static-call updates
+    - x86/static-call: Remove early_boot_irqs_disabled check to fix Xen PVH dom0
+    - x86/asm: Make serialize() always_inline
+    - x86/xen: don't do PV iret hypercall through hypercall page
+    - x86/xen: add central hypercall functions
+    - x86/xen: use new hypercall functions instead of hypercall page
+    - x86/xen: remove hypercall page
+    - ALSA: usb-audio: Fix a DMA to stack memory bug
+    - x86/static-call: fix 32-bit build
+    - Linux 5.15.175
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-53125
+    - bpf: sync_linked_regs() must preserve subreg_def
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56770
+    - net/sched: netem: account for backlog updates from child qdisc
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56659
+    - net: lapb: increase LAPB_HEADER_LEN
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56662
+    - acpi: nfit: vmalloc-out-of-bounds Read in acpi_nfit_ctl
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-42315
+    - exfat: fix potential deadlock on __exfat_get_dentry_set
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-53119
+    - virtio/vsock: Fix accept_queue memory leak
+  * Jammy update: v5.15.175 upstream stable release (LP: #2095302) //
+    CVE-2024-56670
+    - usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to
+      accessing null pointer
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283)
+    - arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
+    - media: venus: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - media: gspca: ov534-ov772x: Fix off-by-one error in set_frame_rate()
+    - media: uvcvideo: Stop stream during unregister
+    - vmstat: call fold_vm_zone_numa_events() before show per zone NUMA event
+    - iommu/io-pgtable-arm: Fix stage-2 map/unmap for concatenated tables
+    - leds: lp55xx: Remove redundant test for invalid channel number
+    - clk: qcom: gcc-qcs404: fix initial rate of GPLL3
+    - samples: pktgen: correct dev to DEV
+    - ARM: 9419/1: mm: Fix kernel memory mapping for xip kernels
+    - x86/mm: Fix a kdump kernel failure on SME system when CONFIG_IMA_KEXEC=y
+    - vdpa/mlx5: Fix PA offset with unaligned starting iotlb map
+    - KVM: nVMX: Treat vpid01 as current if L2 is active, but with VPID disabled
+    - ocfs2: fix UBSAN warning in ocfs2_verify_volume()
+    - drm/bridge: tc358768: Fix DSI command tx
+    - mmc: sunxi-mmc: Add D1 MMC variant
+    - mmc: sunxi-mmc: Fix A100 compatible description
+    - lib/buildid: Fix build ID parsing logic
+    - media: dvbdev: fix the logic when DVB_DYNAMIC_MINORS is not set
+    - NFSD: initialize copy->cp_clp early in nfsd4_copy for use by trace point
+    - NFSD: Async COPY result needs to return a write verifier
+    - NFSD: Initialize struct nfsd4_copy earlier
+    - NFSD: Never decrement pending_async_copies on error
+    - mm: revert "mm: shmem: fix data-race in shmem_getattr()"
+    - mm: avoid unsafe VMA hook invocation when error arises on mmap hook
+    - mm: unconditionally close VMAs on error
+    - mm: refactor arch_calc_vm_flag_bits() and arm64 MTE handling
+    - NFS: nfs_async_write_reschedule_io must not recurse into the writeback code
+    - ASoC: Intel: bytcr_rt5640: Add support for non ACPI instantiated codec
+    - ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet
+    - ASoC: Intel: sst: Support LPE0F28 ACPI HID
+    - wifi: iwlwifi: mvm: Use the sync timepoint API in suspend
+    - mac80211: fix user-power when emulating chanctx
+    - usb: add support for new USB device ID 0x17EF:0x3098 for the r8152 driver
+    - selftests/watchdog-test: Fix system accidentally reset after watchdog-test
+    - ALSA: hda/realtek: Add subwoofer quirk for Infinix ZERO BOOK 13
+    - x86/amd_nb: Fix compile-testing without CONFIG_AMD_NB
+    - net: usb: qmi_wwan: add Quectel RG650V
+    - soc: qcom: Add check devm_kasprintf() returned value
+    - regulator: rk808: Add apply_bit for BUCK3 on RK809
+    - platform/x86: dell-smbios-base: Extends support to Alienware products
+    - platform/x86: dell-wmi-base: Handle META key Lock/Unlock events
+    - can: j1939: fix error in J1939 documentation.
+    - ASoC: stm: Prevent potential division by zero in stm32_sai_mclk_round_rate()
+    - ASoC: stm: Prevent potential division by zero in stm32_sai_get_clk_div()
+    - proc/softirqs: replace seq_printf with seq_put_decimal_ull_width
+    - ALSA: usb-audio: Fix Yamaha P-125 Quirk Entry
+    - ARM: 9420/1: smp: Fix SMP for xip kernels
+    - ipmr: Fix access to mfc_cache_list without lock held
+    - nvme: fix metadata handling in nvme-passthrough
+    - x86/barrier: Do not serialize MSR accesses on AMD
+    - kselftest/arm64: mte: fix printf type warnings about longs
+    - s390/cio: Do not unregister the subchannel based on DNV
+    - brd: remove brd_devices_mutex mutex
+    - mips: asm: fix warning when disabling MIPS_FP_SUPPORT
+    - m68k: mvme147: Fix SCSI controller IRQ numbers
+    - m68k: mvme16x: Add and use "mvme16x.h"
+    - m68k: mvme147: Reinstate early console
+    - arm64: fix .data.rel.ro size assertion when CONFIG_LTO_CLANG
+    - acpi/arm64: Adjust error handling procedure in gtdt_parse_timer_block()
+    - s390/syscalls: Avoid creation of arch/arch/ directory
+    - firmware: google: Unregister driver_info on failure
+    - crypto: qat - remove faulty arbiter config reset
+    - thermal: core: Initialize thermal zones before registering them
+    - EDAC/fsl_ddr: Fix bad bit shift operations
+    - crypto: cavium - Fix the if condition to exit loop after timeout
+    - ACPI: CPPC: Fix _CPC register setting issue
+    - crypto: caam - add error check to caam_rsa_set_priv_key_form
+    - crypto: cavium - Fix an error handling path in cpt_ucode_load_fw()
+    - time: Fix references to _msecs_to_jiffies() handling of values
+    - timekeeping: Consolidate fast timekeeper
+    - seqlock/latch: Provide raw_read_seqcount_latch_retry()
+    - kcsan, seqlock: Support seqcount_latch_t
+    - kcsan, seqlock: Fix incorrect assumption in read_seqbegin()
+    - clocksource/drivers:sp804: Make user selectable
+    - spi: spi-fsl-lpspi: downgrade log level for pio mode
+    - spi: spi-fsl-lpspi: Use IRQF_NO_AUTOEN flag in request_irq()
+    - soc: ti: smartreflex: Use IRQF_NO_AUTOEN flag in request_irq()
+    - mmc: mmc_spi: drop buggy snprintf()
+    - tpm: fix signed/unsigned bug when checking event logs
+    - arm64: dts: mt8183: krane: Fix the address of eeprom at i2c4
+    - arm64: dts: mt8183: kukui: Fix the address of eeprom at i2c4
+    - arm64: dts: mediatek: mt8173-elm-hana: Add vdd-supply to second source
+      trackpad
+    - Revert "cgroup: Fix memory leak caused by missing cgroup_bpf_offline"
+    - cgroup/bpf: only cgroup v2 can be attached by bpf programs
+    - arm64: dts: mt8183: fennel: add i2c2's i2c-scl-internal-delay-ns
+    - arm64: dts: mt8183: burnet: add i2c2's i2c-scl-internal-delay-ns
+    - arm64: dts: mt8183: Damu: add i2c2's i2c-scl-internal-delay-ns
+    - pwm: imx27: Workaround of the pwm output bug when decrease the duty cycle
+    - ARM: dts: cubieboard4: Fix DCDC5 regulator constraints
+    - pmdomain: ti-sci: Add missing of_node_put() for args.np
+    - spi: tegra210-quad: Avoid shift-out-of-bounds
+    - spi: zynqmp-gqspi: Undo runtime PM changes at driver exit time​
+    - regmap: irq: Set lockdep class for hierarchical IRQ domains
+    - arm64: dts: mt8183: jacuzzi: remove unused ddc-i2c-bus
+    - arm64: dts: mt8183: jacuzzi: Move panel under aux-bus
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Fix DP bridge supply names
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add supplies for fixed
+      regulators
+    - selftests/resctrl: Protect against array overrun during iMC config parsing
+    - media: venus: venc: Use pmruntime autosuspend
+    - media: venus: vdec: decoded picture buffer handling during reconfig sequence
+    - media: venus : Addition of EOS Event support for Encoder
+    - media: venus : Addition of support for VIDIOC_TRY_ENCODER_CMD
+    - venus: venc: add handling for VIDIOC_ENCODER_CMD
+    - media: venus: provide ctx queue lock for ioctl synchronization
+    - media: atomisp: remove #ifdef HAS_NO_HMEM
+    - platform/x86: panasonic-laptop: Replace snprintf in show functions with
+      sysfs_emit
+    - platform/x86: panasonic-laptop: Return errno correctly in show callback
+    - drm/mm: Mark drm_mm_interval_tree*() functions with __maybe_unused
+    - drm/omap: Fix possible NULL dereference
+    - drm/omap: Fix locking in omap_gem_new_dmabuf()
+    - wifi: p54: Use IRQF_NO_AUTOEN flag in request_irq()
+    - wifi: mwifiex: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/imx/dcss: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/imx/ipuv3: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/v3d: Address race-condition in MMU flush
+    - wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss1
+    - wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss2
+    - dt-bindings: vendor-prefixes: Add NeoFidelity, Inc
+    - ASoC: fsl_micfil: Drop unnecessary register read
+    - ASoC: fsl_micfil: do not define SHIFT/MASK for single bits
+    - ASoC: fsl_micfil: use GENMASK to define register bit fields
+    - ASoC: fsl_micfil: fix regmap_write_bits usage
+    - ASoC: dt-bindings: mt6359: Update generic node name and dmic-mode
+    - drm/bridge: anx7625: Drop EDID cache on bridge power off
+    - libbpf: Fix output .symtab byte-order during linking
+    - bpf: Fix the xdp_adjust_tail sample prog issue
+    - libbpf: fix sym_is_subprog() logic for weak global subprogs
+    - xfrm: rename xfrm_state_offload struct to allow reuse
+    - xfrm: store and rely on direction to construct offload flags
+    - netdevsim: rely on XFRM state direction instead of flags
+    - netdevsim: copy addresses for both in and out paths
+    - drm/bridge: tc358767: Fix link properties discovery
+    - selftests/bpf: Fix msg_verify_data in test_sockmap
+    - selftests/bpf: Fix txmsg_redir of test_txmsg_pull in test_sockmap
+    - drm: fsl-dcu: enable PIXCLK on LS1021A
+    - drm/panfrost: Remove unused id_mask from struct panfrost_model
+    - drm/msm/adreno: Use IRQF_NO_AUTOEN flag in request_irq()
+    - drm/etnaviv: Request pages from DMA32 zone on addressing_limited
+    - drm/etnaviv: fix power register offset on GC300
+    - drm/etnaviv: hold GPU lock across perfmon sampling
+    - wifi: wfx: Fix error handling in wfx_core_init()
+    - drm/msm/dpu: cast crtc_clk calculation to u64 in _dpu_core_perf_calc_clk()
+    - netfilter: nf_tables: skip transaction if update object is not implemented
+    - netfilter: nf_tables: must hold rcu read lock while iterating object type
+      list
+    - netlink: typographical error in nlmsg_type constants definition
+    - selftests/bpf: Add txmsg_pass to pull/push/pop in test_sockmap
+    - selftests/bpf: Fix SENDPAGE data logic in test_sockmap
+    - selftests, bpf: Add one test for sockmap with strparser
+    - selftests/bpf: Fix total_bytes in msg_loop_rx in test_sockmap
+    - selftests/bpf: Add push/pop checking for msg_verify_data in test_sockmap
+    - bpf, sockmap: Several fixes to bpf_msg_push_data
+    - bpf, sockmap: Fix sk_msg_reset_curr
+    - selftests: net: really check for bg process completion
+    - drm/amdkfd: Fix wrong usage of INIT_WORK()
+    - net: rfkill: gpio: Add check for clk_enable()
+    - driver core: Introduce device_find_any_child() helper
+    - netpoll: Use rcu_access_pointer() in netpoll_poll_lock
+    - wireguard: selftests: load nf_conntrack if not present
+    - trace/trace_event_perf: remove duplicate samples on the first tracepoint
+      event
+    - pinctrl: zynqmp: drop excess struct member description
+    - powerpc/vdso: Flag VDSO64 entry points as functions
+    - mfd: tps65010: Use IRQF_NO_AUTOEN flag in request_irq() to fix race
+    - mfd: da9052-spi: Change read-mask to write-mask
+    - mfd: intel_soc_pmic_bxtwc: Use dev_err_probe()
+    - cpufreq: loongson2: Unregister platform_driver on failure
+    - mtd: rawnand: atmel: Fix possible memory leak
+    - RDMA/bnxt_re: Check cqe flags to know imm_data vs inv_irkey
+    - clk: imx: lpcg-scu: SW workaround for errata (e10858)
+    - clk: imx: clk-scu: fix clk enable state save and restore
+    - mfd: rt5033: Fix missing regmap_del_irq_chip()
+    - scsi: fusion: Remove unused variable 'rc'
+    - RDMA/hns: Fix out-of-order issue of requester when setting FENCE
+    - powerpc/sstep: make emulate_vsx_load and emulate_vsx_store static
+    - powerpc/kexec: Fix return of uninitialized variable
+    - fbdev/sh7760fb: Alloc DMA memory from hardware device
+    - dt-bindings: clock: axi-clkgen: include AXI clk
+    - clk: clk-axi-clkgen: make sure to enable the AXI bus clock
+    - pinctrl: k210: Undef K210_PC_DEFAULT
+    - mailbox: arm_mhuv2: clean up loop in get_irq_chan_comb()
+    - perf cs-etm: Don't flush when packet_queue fills up
+    - perf probe: Fix libdw memory leak
+    - perf probe: Correct demangled symbols in C++ program
+    - PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
+    - PCI: cpqphp: Fix PCIBIOS_* return value confusion
+    - f2fs: fix the wrong f2fs_bug_on condition in f2fs_do_replace_block
+    - f2fs: remove struct segment_allocation default_salloc_ops
+    - f2fs: open code allocate_segment_by_default
+    - f2fs: remove the unused flush argument to change_curseg
+    - f2fs: check curseg->inited before write_sum_page in change_curseg
+    - perf trace: avoid garbage when not printing a trace event's arguments
+    - m68k: mcfgpio: Fix incorrect register offset for CONFIG_M5441x
+    - m68k: coldfire/device.c: only build FEC when HW macros are defined
+    - perf trace: Do not lose last events in a race
+    - perf trace: Avoid garbage when not printing a syscall's arguments
+    - rpmsg: glink: Add TX_DATA_CONT command while sending
+    - rpmsg: glink: Send READ_NOTIFY command in FIFO full case
+    - rpmsg: glink: Fix GLINK command prefix
+    - rpmsg: glink: use only lower 16-bits of param2 for CMD_OPEN name length
+    - remoteproc: qcom_q6v5_mss: Re-order writes to the IMEM region
+    - NFSD: Cap the number of bytes copied by nfs4_reset_recoverydir()
+    - sunrpc: simplify two-level sysctl registration for svcrdma_parm_table
+    - NFSD: Fix nfsd4_shutdown_copy()
+    - hwmon: (tps23861) Fix reporting of negative temperatures
+    - vdpa/mlx5: Fix suboptimal range on iotlb iteration
+    - selftests/mount_setattr: Fix failures on 64K PAGE_SIZE kernels
+    - fs_parser: update mount_api doc to match function signature
+    - power: supply: core: Remove might_sleep() from power_supply_put()
+    - power: supply: bq27xxx: Fix registers of bq27426
+    - net: usb: lan78xx: Fix memory leak on device unplug by freeing PHY device
+    - tg3: Set coherent DMA mask bits to 31 for BCM57766 chipsets
+    - net: usb: lan78xx: Fix refcounting and autosuspend on invalid WoL
+      configuration
+    - net: mdio-ipq4019: add missing error check
+    - marvell: pxa168_eth: fix call balance of pep->clk handling routines
+    - net: stmmac: dwmac-socfpga: Set RX watchdog interrupt as broken
+    - octeontx2-af: RPM: Fix mismatch in lmac type
+    - spi: atmel-quadspi: Fix register name in verbose logging function
+    - net: hsr: fix hsr_init_sk() vs network/transport headers.
+    - bnxt_en: Reserve rings after PCIe AER recovery if NIC interface is down
+    - iio: light: al3010: Fix an error handling path in al3010_probe()
+    - usb: using mutex lock and supporting O_NONBLOCK flag in iowarrior_read()
+    - usb: yurex: make waiting on yurex_write interruptible
+    - USB: chaoskey: fail open after removal
+    - USB: chaoskey: Fix possible deadlock chaoskey_list_lock
+    - misc: apds990x: Fix missing pm_runtime_disable()
+    - counter: stm32-timer-cnt: Add check for clk_enable()
+    - ALSA: hda/realtek: Update ALC256 depop procedure
+    - apparmor: fix 'Do simple duplicate message elimination'
+    - usb: ehci-spear: fix call balance of sehci clk handling routines
+    - Revert "drivers: clk: zynqmp: update divider round rate logic"
+    - ASoC: Intel: sst: Fix used of uninitialized ctx to log an error
+    - soc: qcom: socinfo: fix revision check in qcom_socinfo_probe()
+    - ext4: supress data-race warnings in ext4_free_inodes_{count,set}()
+    - ext4: fix FS_IOC_GETFSMAP handling
+    - jfs: xattr: check invalid xattr size more strictly
+    - ASoC: codecs: Fix atomicity violation in snd_soc_component_get_drvdata()
+    - perf/x86/intel/pt: Fix buffer full but size is 0 case
+    - crypto: x86/aegis128 - access 32-bit arguments as 32-bit
+    - powerpc/pseries: Fix KVM guest detection for disabling hardlockup detector
+    - KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
+    - fsnotify: fix sending inotify event with unexpected filename
+    - tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler
+    - locking/lockdep: Avoid creating new name string literals in
+      lockdep_set_subclass()
+    - exfat: fix uninit-value in __exfat_get_dentry_set
+    - Bluetooth: Fix type of len in rfcomm_sock_getsockopt{,_old}()
+    - usb: xhci: Fix TD invalidation under pending Set TR Dequeue
+    - Revert "usb: gadget: composite: fix OS descriptors w_value logic"
+    - serial: sh-sci: Clean sci_ports[0] after at earlycon exit
+    - Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"
+    - gpio: exar: set value when external pull-up or pull-down is present
+    - spi: Fix acpi deferred irq probe
+    - mtd: spi-nor: core: replace dummy buswidth from addr to data
+    - cpufreq: mediatek-hw: Fix wrong return value in mtk_cpufreq_get_cpu_power()
+    - platform/chrome: cros_ec_typec: fix missing fwnode reference decrement
+    - ubi: wl: Put source PEB into correct list if trying locking LEB failed
+    - serial: 8250: omap: Move pm_runtime_get_sync
+    - arm64: tls: Fix context-switching of tpidrro_el0 when kpti is enabled
+    - block: fix ordering between checking BLK_MQ_S_STOPPED request adding
+    - HID: wacom: Interpret tilt data from Intuos Pro BT as signed values
+    - soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
+    - media: v4l2-core: v4l2-dv-timings: check cvt/gtf result
+    - ALSA: hda/realtek: Update ALC225 depop procedure
+    - ALSA: hda/realtek: Set PCBeep to default value for ALC274
+    - ALSA: hda/realtek: Fix Internal Speaker and Mic boost of Infinix Y4 Max
+    - ALSA: hda/realtek: Apply quirk for Medion E15433
+    - usb: dwc3: gadget: Fix checking for number of TRBs left
+    - lib: string_helpers: silence snprintf() output truncation warning
+    - rpmsg: glink: Propagate TX failures in intentless mode as well
+    - um: Fix the return value of elf_core_copy_task_fpregs
+    - um: Always dump trace for specified task in show_stack
+    - rtc: st-lpc: Use IRQF_NO_AUTOEN flag in request_irq()
+    - rtc: abx80x: Fix WDT bit position of the status register
+    - ubifs: Correct the total block count by deducting journal reservation
+    - jffs2: fix use of uninitialized variable
+    - block: return unsigned int from bdev_io_min
+    - 9p/xen: fix init sequence
+    - rtc: ab-eoz9: don't fail temperature reads on undervoltage notification
+    - modpost: remove incorrect code in do_eisa_entry()
+    - nfs: ignore SB_RDONLY when mounting nfs
+    - sunrpc: remove unnecessary test in rpc_task_set_client()
+    - SUNRPC: Replace internal use of SOCKWQ_ASYNC_NOSPACE
+    - ASoC: fsl_micfil: fix the naming style for mask definition
+    - xfs: fix log recovery when unknown rocompat bits are set
+    - xfs: remove unknown compat feature check in superblock write validation
+    - btrfs: add might_sleep() annotations
+    - util_macros.h: fix/rework find_closest() macros
+    - scsi: ufs: exynos: Fix hibern8 notify callbacks
+    - PCI: keystone: Add link up check to ks_pcie_other_map_bus()
+    - ovl: properly handle large files in ovl_security_fileattr
+    - dm thin: Add missing destroy_work_on_stack()
+    - PCI: rockchip-ep: Fix address translation unit programming
+    - drm/etnaviv: flush shader L1 cache after user commandstream
+    - iTCO_wdt: mask NMI_NOW bit for update_no_reboot_bit() call
+    - watchdog: mediatek: Make sure system reset gets asserted in
+      mtk_wdt_restart()
+    - can: peak_usb: CANFD: store 64-bits hw timestamps
+    - can: do not increase rx statistics when generating a CAN rx error message
+      frame
+    - can: c_can: c_can_handle_bus_err(): update statistics if skb allocation
+      fails
+    - can: sun4i_can: sun4i_can_err(): call can_change_state() even if cf is NULL
+    - can: m_can: m_can_handle_lec_err(): fix {rx,tx}_errors statistics
+    - can: ifi_canfd: ifi_canfd_handle_lec_err(): fix {rx,tx}_errors statistics
+    - can: sun4i_can: sun4i_can_err(): fix {rx,tx}_errors statistics
+    - can: ems_usb: ems_usb_rx_err(): fix {rx,tx}_errors statistics
+    - ipvs: fix UB due to uninitialized stack access in ip_vs_protocol_init()
+    - ptp: Add error handling for adjfine callback in ptp_clock_adjtime
+    - net/sched: tbf: correct backlog statistic for GSO packets
+    - net/smc: Limit backlog connections
+    - net/qed: allow old cards not supporting "num_images" to work
+    - net: sched: fix erspan_opt settings in cls_flower
+    - netfilter: nft_set_hash: skip duplicated elements pending gc run
+    - netfilter: nft_set_hash: unaligned atomic read on struct nft_set_ext
+    - ethtool: Fix wrong mod state in case of verbose and no_mask bitset
+    - gpio: grgpio: use a helper variable to store the address of ofdev->dev
+    - dt_bindings: rs485: Correct delay values
+    - dt-bindings: serial: rs485: Fix rs485-rts-delay property
+    - serial: amba-pl011: Use port lock wrappers
+    - serial: amba-pl011: Fix RX stall when DMA is used
+    - bpftool: Remove asserts from JIT disassembler
+    - bpftool: fix potential NULL pointer dereferencing in prog_dump()
+    - drm/sti: Add __iomem for mixer_dbg_mxn's parameter
+    - ALSA: pcm: Add more disconnection checks at file ops
+    - ALSA: pcm: Avoid reference to status->state
+    - ALSA: usb-audio: Notify xrun for low-latency mode
+    - tools: Override makefile ARCH variable if defined, but empty
+    - drm/v3d: Enable Performance Counters before clearing them
+    - bpf: Handle BPF_EXIST and BPF_NOEXIST for LPM trie
+    - bpf: Fix exact match conditions in trie_get_next_key()
+    - watchdog: rti: of: honor timeout-sec property
+    - tracing: Fix cmp_entries_dup() to respect sort() comparison rules
+    - ALSA: usb-audio: add mixer mapping for Corsair HS80
+    - ALSA: hda/realtek: Enable mute and micmute LED on HP ProBook 430 G8
+    - ALSA: hda/realtek: Add support for Samsung Galaxy Book3 360 (NP730QFG)
+    - scsi: qla2xxx: Fix abort in bsg timeout
+    - scsi: qla2xxx: Fix NVMe and NPIV connect issue
+    - scsi: qla2xxx: Supported speed displayed incorrectly for VPorts
+    - scsi: qla2xxx: Remove check req_sg_cnt should be equal to rsp_sg_cnt
+    - dma-buf: fix dma_fence_array_signaled v4
+    - regmap: detach regmap from dev on regmap_exit
+    - mmc: sdhci-pci: Add DMI quirk for missing CD GPIO on Vexia Edu Atla 10
+      tablet
+    - mmc: core: Further prevent card detect during shutdown
+    - ocfs2: update seq_file index in ocfs2_dlm_seq_next
+    - epoll: annotate racy check
+    - btrfs: avoid unnecessary device path update for the same device
+    - kselftest/arm64: Don't leak pipe fds in pac.exec_sign_all()
+    - media: uvcvideo: Add a quirk for the Kaiweets KTI-W02 infrared camera
+    - media: cx231xx: Add support for Dexatek USB Video Grabber 1d19:6108
+    - drm/vc4: hvs: Set AXI panic modes for the HVS
+    - drm: panel-orientation-quirks: Add quirk for AYA NEO 2 model
+    - drm/mcde: Enable module autoloading
+    - drm/radeon/r600_cs: Fix possible int overflow in r600_packet3_check()
+    - r8169: don't apply UDP padding quirk on RTL8126A
+    - samples/bpf: Fix a resource leak
+    - net: fec_mpc52xx_phy: Use %pa to format resource_size_t
+    - net: ethernet: fs_enet: Use %pa to format resource_size_t
+    - net/sched: cbs: Fix integer overflow in cbs_set_port_rate()
+    - Bluetooth: L2CAP: handle NULL sock pointer in l2cap_sock_alloc
+    - wifi: ath5k: add PCI ID for SX76X
+    - wifi: ath5k: add PCI ID for Arcadyan devices
+    - drm/panel: simple: Add Microchip AC69T88A LVDS Display panel
+    - drm/amdgpu: clear RB_OVERFLOW bit when enabling interrupts for vega20_ih
+    - drm/amdgpu: Dereference the ATCS ACPI buffer
+    - drm/amdgpu: refine error handling in amdgpu_ttm_tt_pin_userptr
+    - drm/amdgpu: skip amdgpu_device_cache_pci_state under sriov
+    - wifi: ipw2x00: libipw_rx_any(): fix bad alignment
+    - ASoC: hdmi-codec: reorder channel allocation list
+    - rocker: fix link status detection in rocker_carrier_init()
+    - net/neighbor: clear error in case strict check is not set
+    - netpoll: Use rcu_access_pointer() in __netpoll_setup
+    - pinctrl: freescale: fix COMPILE_TEST error with PINCTRL_IMX_SCU
+    - tracing: Use atomic64_inc_return() in trace_clock_counter()
+    - scsi: st: Don't modify unknown block number in MTIOCGET
+    - scsi: st: Add MTIOCGET and MTLOAD to ioctls allowed after device reset
+    - pinctrl: qcom-pmic-gpio: add support for PM8937
+    - nvdimm: rectify the illogical code within nd_dax_probe()
+    - PCI: Detect and trust built-in Thunderbolt chips
+    - PCI: Add 'reset_subordinate' to reset hierarchy below bridge
+    - PCI: Add ACS quirk for Wangxun FF5xxx NICs
+    - usb: chipidea: udc: handle USB Error Interrupt if IOC not set
+    - misc: eeprom: eeprom_93cx6: Add quirk for extra read clock cycle
+    - modpost: Include '.text.*' in TEXT_SECTIONS
+    - modpost: Add .irqentry.text to OTHER_SECTIONS
+    - sched/core: Remove the unnecessary need_resched() check in nohz_csd_func()
+    - sched/fair: Add NOHZ balancer flag for nohz.next_balance updates
+    - sched/fair: Check idle_cpu() before need_resched() to detect ilb CPU turning
+      busy
+    - sched/core: Prevent wakeup of ksoftirqd during idle load balance
+    - btrfs: fix missing snapshot drew unlock when root is dead during swap
+      activation
+    - tracing/eprobe: Fix to release eprobe when failed to add dyn_event
+    - Revert "unicode: Don't special case ignorable code points"
+    - KVM: arm64: vgic-its: Add a data length check in vgic_its_save_*
+    - KVM: arm64: vgic-its: Clear DTE when MAPD unmaps a device
+    - KVM: arm64: vgic-its: Clear ITE when DISCARD frees an ITE
+    - jffs2: Fix rtime decompressor
+    - mm/damon/vaddr-test: split a test function having >1024 bytes frame size
+    - mm/damon/vaddr: fix issue in damon_va_evenly_split_region()
+    - xhci: dbc: Fix STALL transfer event handling
+    - mmc: mtk-sd: Fix error handle of probe function
+    - ocfs2: Revert "ocfs2: fix the la space leak when unmounting an ocfs2 volume"
+    - Revert "drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()"
+    - scsi: core: Fix scsi_mode_select() buffer length handling
+    - gve: Fixes for napi_poll when budget is 0
+    - arm64: smccc: Remove broken support for SMCCCv1.3 SVE discard hint
+    - net: dsa: microchip: correct KSZ8795 static MAC table access
+    - drm/amdgpu: rework resume handling for display (v2)
+    - serial: amba-pl011: fix build regression
+    - media: venus: vdec: fixed possible memory leak issue
+    - net/smc: Fix af_ops of child socket pointing to released memory
+    - Bluetooth: hci_core: Fix calling mgmt_device_connected
+    - Linux 5.15.174
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46871
+    - drm/amd/display: Correct the defined value for AMDGPU_DMUB_NOTIFICATION_MAX
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49950
+    - Bluetooth: L2CAP: Fix uaf in l2cap_connect
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50275
+    - arm64/sve: Discard stale CPU state when handling SVE traps
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-47730
+    - crypto: hisilicon/qm - inject error before stopping queue
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46809
+    - drm/amd/display: Check BIOS images before it is used
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57850
+    - jffs2: Prevent rtime decompress memory corruption
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56781
+    - powerpc/prom_init: Fixup missing powermac #size-cells
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56785
+    - MIPS: Loongson64: DTS: Really fix PCIe port nodes for ls7a
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-43098
+    - i3c: Use i3cdev->desc->info instead of calling i3c_device_get_info() to
+      avoid deadlock
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-45828
+    - i3c: mipi-i3c-hci: Mask ring interrupts before ring stop request
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56586
+    - f2fs: fix f2fs_bug_on when uninstalling filesystem call f2fs_evict_inode.
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56587
+    - leds: class: Protect brightness_show() with led_cdev->led_access mutex
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56589
+    - scsi: hisi_sas: Add cond_resched() for no forced preemption model
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56590
+    - Bluetooth: hci_core: Fix not checking skb length on hci_acldata_packet
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56593
+    - wifi: brcmfmac: Fix oops due to NULL pointer dereference in
+      brcmf_sdiod_sglist_rw()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56594
+    - drm/amdgpu: set the right AMDGPU sg segment limitation
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56595
+    - jfs: add a check to prevent array-index-out-of-bounds in dbAdjTree
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56596
+    - jfs: fix array-index-out-of-bounds in jfs_readdir
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56597
+    - jfs: fix shift-out-of-bounds in dbSplit
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56598
+    - jfs: array-index-out-of-bounds fix in dtReadFirst
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-47143
+    - dma-debug: fix a possible deadlock on radix_lock
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56600
+    - net: inet6: do not leave a dangling sk pointer in inet6_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56601
+    - net: inet: do not leave a dangling sk pointer in inet_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56602
+    - net: ieee802154: do not leave a dangling sk pointer in ieee802154_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56603
+    - net: af_can: do not leave a dangling sk pointer in can_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56605
+    - Bluetooth: L2CAP: do not leave dangling sk pointer on error in
+      l2cap_sock_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56606
+    - af_packet: avoid erroring out after sock_init_data() in packet_create()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56787
+    - soc: imx8m: Probe the SoC driver as platform driver
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56610
+    - kcsan: Turn report_filterlist_lock into a raw_spinlock
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57849
+    - s390/cpum_sf: Handle CPU hotplug remove during sampling
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56568
+    - iommu/arm-smmu: Defer probe of clients after smmu device bound
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56614
+    - xsk: fix OOB map writes when deleting elements
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56615
+    - bpf: fix OOB devmap writes when deleting elements
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-48881
+    - bcache: revert replacing IS_ERR_OR_NULL with IS_ERR again
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56619
+    - nilfs2: fix potential out-of-bounds memory access in nilfs_find_entry()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56622
+    - scsi: ufs: core: sysfs: Prevent div by zero
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56623
+    - scsi: qla2xxx: Fix use after free on unload
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57874
+    - arm64: ptrace: fix partial SETREGSET for NT_ARM_TAGGED_ADDR_CTRL
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56625
+    - can: dev: can_set_termination(): allow sleeping GPIOs
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56629
+    - HID: wacom: fix when get product name maybe null pointer
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56630
+    - ocfs2: free inode when ocfs2_get_init_inode() fails
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50051
+    - spi: mpc52xx: Add cancel_work_sync before module remove
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56633
+    - tcp_bpf: Fix the sk_mem_uncharge logic in tcp_bpf_sendmsg
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56634
+    - gpio: grgpio: Add NULL check in grgpio_probe
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56636
+    - geneve: do not assume mac header is set in geneve_xmit_skb()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56637
+    - netfilter: ipset: Hold module reference while requesting a module
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-52332
+    - igb: Fix potential invalid memory access in igb_init_module()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56640
+    - net/smc: fix LGR and link use-after-free issue
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56642
+    - tipc: Fix use-after-free of kernel socket in cleanup_bearer().
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56643
+    - dccp: Fix memory leak in dccp_feat_change_recv
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56644
+    - net/ipv6: release expired exception dst cached in socket
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56645
+    - can: j1939: j1939_session_new(): fix skb reference counting
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56648
+    - net: hsr: avoid potential out-of-bound access in fill_frame_info()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56650
+    - netfilter: x_tables: fix LED ID check in led_tg_check()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56776
+    - drm/sti: avoid potential dereference of error pointers
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56777
+    - drm/sti: avoid potential dereference of error pointers in
+      sti_gdp_atomic_check
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56778
+    - drm/sti: avoid potential dereference of error pointers in
+      sti_hqvdp_atomic_check
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-46841
+    - btrfs: don't BUG_ON on ENOMEM from btrfs_lookup_extent_info() in
+      walk_down_proc()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56779
+    - nfsd: fix nfs4_openowner leak when concurrent nfsd4_open occur
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56558
+    - nfsd: make sure exp active before svc_export_show
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56562
+    - i3c: master: Fix miss free init_dyn_addr at i3c_master_put_i3c_addrs()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-57838
+    - s390/entry: Mark IRQ entries to fix stack depot warnings
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56567
+    - ad7780: fix division by zero in ad7780_write_raw()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56581
+    - btrfs: ref-verify: fix use-after-free after invalid ref action
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56774
+    - btrfs: add a sanity check for btrfs root in btrfs_search_slot()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56780
+    - quota: flush quota_release_work upon quota writeback
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53165
+    - sh: intc: Fix use-after-free bug in register_intc_controller()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56688
+    - sunrpc: clear XPRT_SOCK_UPD_TIMEOUT when reset transport
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56704
+    - 9p/xen: fix release of IRQ
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53171
+    - ubifs: authentication: Fix use-after-free in ubifs_tnc_end_commit
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53172
+    - ubi: fastmap: Fix duplicate slab cache names while attaching
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56739
+    - rtc: check if __rtc_read_time was successful in rtc_timer_do_work()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53173
+    - NFSv4.0: Fix a use-after-free problem in the asynchronous open()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53145
+    - um: Fix potential integer overflow during physmem setup
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53174
+    - SUNRPC: make sure cache entry active before cache_show
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53146
+    - NFSD: Prevent a potential integer overflow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56698
+    - usb: dwc3: gadget: Fix looping of queued SG entries
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53180
+    - ALSA: pcm: Add sanity NULL check for the default mmap fault handler
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56700
+    - media: wl128x: Fix atomicity violation in fmc_send_cmd()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2022-49034
+    - sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53181
+    - um: vector: Do not use drvdata in release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53183
+    - um: net: Do not use drvdata in release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53184
+    - um: ubd: Do not use drvdata in release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50055
+    - driver core: bus: Fix double free in driver API bus_register()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56741
+    - apparmor: test: Fix memory leak for aa_unpack_strdup()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53148
+    - comedi: Flush partial mappings in error case
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53194
+    - PCI: Fix use-after-free of slot->bus on hot remove
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53197
+    - ALSA: usb-audio: Fix potential out-of-bound accesses for Extigy and Mbox
+      devices
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53150
+    - ALSA: usb-audio: Fix out of bounds reads when finding clock sources
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53198
+    - xen: Fix the issue of resource not being properly released in
+      xenbus_dev_probe()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-50283
+    - ksmbd: fix slab-use-after-free in smb3_preauth_hash_rsp
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53206
+    - tcp: Fix use-after-free of nreq in reqsk_timer_handler().
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53214
+    - vfio/pci: Properly hide first-in-list PCIe extended capability
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53215
+    - svcrdma: fix miss destroy percpu_counter in svc_rdma_proc_init()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53217
+    - NFSD: Prevent NULL dereference in nfsd4_process_cb_update()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53151
+    - svcrdma: Address an integer overflow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56745
+    - PCI: Fix reset_method_store() memory leak
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56746
+    - fbdev: sh7760fb: Fix a possible memory leak in sh7760fb_alloc_mem()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53155
+    - ocfs2: fix uninitialized value in ocfs2_file_read_iter()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53226
+    - RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56747
+    - scsi: qedi: Fix a possible memory leak in qedi_alloc_and_init_sb()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56748
+    - scsi: qedf: Fix a possible memory leak in qedf_alloc_and_init_sb()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53227
+    - scsi: bfa: Fix use-after-free in bfad_im_module_exit()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56701
+    - powerpc/pseries: Fix dtl_access_lock to be a rw_semaphore
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56678
+    - powerpc/mm/fault: Fix kfence page fault reporting
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56723
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for PMIC devices
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56724
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for TMU device
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56691
+    - mfd: intel_soc_pmic_bxtwc: Use IRQ domain for USB Type-C device
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56694
+    - bpf: fix recursive lock when verdict program return SK_PASS
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53237
+    - Bluetooth: fix use-after-free in device_for_each_child()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53239
+    - ALSA: 6fire: Release resources at card release
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56531
+    - ALSA: caiaq: Use snd_card_free_when_closed() at disconnection
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56532
+    - ALSA: us122l: Use snd_card_free_when_closed() at disconnection
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56533
+    - ALSA: usx2y: Use snd_card_free_when_closed() at disconnection
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56720
+    - bpf, sockmap: Several fixes to bpf_msg_pop_data
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56726
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in cn10k.c
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56728
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_ethtool.c
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56679
+    - octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_common.c
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56539
+    - wifi: mwifiex: Fix memcpy() field-spanning write warning in
+      mwifiex_config_scan()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53156
+    - wifi: ath9k: add range check for conn_rsp_epid in htc_connect_service()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56705
+    - media: atomisp: Add check for rgby_data memory allocation failure
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53157
+    - firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53158
+    - soc: qcom: geni-se: fix array underflow in geni_se_clk_tbl_get()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56681
+    - crypto: bcm - add error check in the ahash_hmac_init function
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56708
+    - EDAC/igen6: Avoid segmentation fault on module unload
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56690
+    - crypto: pcrypt - Call crypto layer directly when padata_do_parallel() return
+      -EBUSY
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53161
+    - EDAC/bluefield: Fix potential integer overflow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56754
+    - crypto: caam - Fix the pointer passed to caam_qi_shutdown()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56548
+    - hfsplus: don't query the device logical block size multiple times
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56756
+    - nvme-pci: fix freeing of the HMB descriptor table
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53142
+    - initramfs: avoid filename buffer overrun
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56693
+    - brd: defer automatic disk creation until module initialization succeeds
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49996
+    - cifs: Fix buffer overflow when parsing NFS reparse points
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53096
+    - mm: resolve faulty mmap_region() error path behaviour
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53122
+    - mptcp: cope racing subflow creation in mptcp_rcv_space_adjust
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-49974
+    - NFSD: Limit the number of concurrent async COPY operations
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53127
+    - Revert "mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K"
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53130
+    - nilfs2: fix null-ptr-deref in block_dirty_buffer tracepoint
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53131
+    - nilfs2: fix null-ptr-deref in block_touch_buffer tracepoint
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53135
+    - KVM: VMX: Bury Intel PT virtualization (guest/host mode) behind
+      CONFIG_BROKEN
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53112
+    - ocfs2: uncache inode which has failed entering the group
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53113
+    - mm: fix NULL pointer dereference in alloc_pages_bulk_noprof
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53120
+    - net/mlx5e: CT: Fix null-ptr-deref in add rule err flow
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53138
+    - net/mlx5e: kTLS, Fix incorrect page refcounting
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53121
+    - net/mlx5: fs, lock FTE when checking if active
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53129
+    - drm/rockchip: vop: Fix a dereferenced before check warning
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-53140
+    - netlink: terminate outstanding dump on socket close
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56569
+    - ftrace: Fix regression with module command in stack_trace_filter
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56570
+    - ovl: Filter invalid inodes with missing lookup function
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56572
+    - media: platform: allegro-dvt: Fix possible memory leak in
+      allocate_buffers_internal()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56574
+    - media: ts2020: fix null-ptr-deref in ts2020_probe()
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56575
+    - media: imx-jpeg: Ensure power suppliers be suspended before detach them
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56576
+    - media: i2c: tc358743: Fix crash in the probe error path when using polling
+  * Jammy update: v5.15.174 upstream stable release (LP: #2095283) //
+    CVE-2024-56578
+    - media: imx-jpeg: Set video drvdata before register video device
+  * CVE-2024-56672
+    - blk-cgroup: Fix UAF in blkcg_unpin_online()
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Thu, 06 Mar 2025 12:03:48 +0800
+
+linux-xilinx-zynqmp (5.15.0-1043.47) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1043.47 -proposed tracker (LP: #2093732)
+
+  [ Ubuntu: 5.15.0-133.144 ]
+
+  * CVE-2025-0927
+    - SAUCE: fs: hfs/hfsplus: add key_len boundary check to hfs_bnode_read_key
+
+  [ Ubuntu: 5.15.0-132.143 ]
+
+  * jammy/linux: 5.15.0-132.143 -proposed tracker (LP: #2093735)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2025.01.13)
+  * KVM: Cache CPUID at KVM.ko module init to reduce latency of VM-Enter and VM-
+    Exit (LP: #2093146)
+    - kvm: x86: Fix xstate_required_size() to follow XSTATE alignment rule
+    - KVM: x86: Cache CPUID.0xD XSTATE offsets+sizes during module init
+  * Jammy update: v5.15.173 upstream stable release (LP: #2089541)
+    - 9p: Avoid creating multiple slab caches with the same name
+    - irqchip/ocelot: Fix trigger register address
+    - block: Fix elevator_get_default() checking for NULL q->tag_set
+    - HID: multitouch: Add support for B2402FVA track point
+    - HID: multitouch: Add quirk for HONOR MagicBook Art 14 touchpad
+    - bpf: use kvzmalloc to allocate BPF verifier environment
+    - crypto: marvell/cesa - Disable hash algorithms
+    - sound: Make CONFIG_SND depend on INDIRECT_IOMEM instead of UML
+    - drm/vmwgfx: Limit display layout ioctl array size to
+      VMWGFX_NUM_DISPLAY_UNITS
+    - powerpc/powernv: Free name on error in opal_event_init()
+    - vDPA/ifcvf: Fix pci_read_config_byte() return code handling
+    - fs: Fix uninitialized value issue in from_kuid and from_kgid
+    - HID: multitouch: Add quirk for Logitech Bolt receiver w/ Casa touchpad
+    - HID: lenovo: Add support for Thinkpad X1 Tablet Gen 3 keyboard
+    - net: usb: qmi_wwan: add Fibocom FG132 0x0112 composition
+    - md/raid10: improve code of mrdev in raid10_sync_request
+    - mm/memory: add non-anonymous page check in the copy_present_page()
+    - udf: Allocate name buffer in directory iterator on heap
+    - udf: Avoid directory type conversion failure due to ENOMEM
+    - 9p: fix slab cache name creation for real
+    - Linux 5.15.173
+  * Jammy update: v5.15.173 upstream stable release (LP: #2089541) //
+    CVE-2024-41080
+    - io_uring: fix possible deadlock in io_register_iowq_max_workers()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533)
+    - arm64: dts: rockchip: Fix rt5651 compatible value on rk3399-sapphire-
+      excavator
+    - arm64: dts: rockchip: Remove hdmi's 2nd interrupt on rk3328
+    - arm64: dts: rockchip: Fix bluetooth properties on Rock960 boards
+    - arm64: dts: rockchip: Remove #cooling-cells from fan on Theobroma lion
+    - arm64: dts: rockchip: Fix LED triggers on rk3308-roc-cc
+    - arm64: dts: imx8mp: correct sdhc ipg clk
+    - ARM: dts: rockchip: fix rk3036 acodec node
+    - ARM: dts: rockchip: drop grf reference from rk3036 hdmi
+    - ARM: dts: rockchip: Fix the spi controller on rk3036
+    - ARM: dts: rockchip: Fix the realtek audio codec on rk3036-kylin
+    - NFSv3: only use NFS timeout for MOUNT when protocols are compatible
+    - NFS: Add a tracepoint to show the results of nfs_set_cache_invalid()
+    - NFSv3: handle out-of-order write replies.
+    - nfs: avoid i_lock contention in nfs_clear_invalid_mapping
+    - net: enetc: set MAC address to the VF net_device
+    - can: c_can: fix {rx,tx}_errors statistics
+    - net: phy: ti: add PHY_RST_AFTER_CLK_EN flag
+    - net: stmmac: Fix unbalanced IRQ wake disable warning on single irq case
+    - Revert "ALSA: hda/conexant: Mute speakers at suspend / shutdown"
+    - media: stb0899_algo: initialize cfr before using it
+    - media: dvb_frontend: don't play tricks with underflow values
+    - media: adv7604: prevent underflow condition when reporting colorspace
+    - scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
+    - ALSA: firewire-lib: fix return value on fail in amdtp_tscm_init()
+    - media: pulse8-cec: fix data timestamp at pulse8_setup()
+    - media: v4l2-ctrls-api: fix error handling for v4l2_g_ctrl()
+    - pwm: imx-tpm: Use correct MODULO value for EPWM mode
+    - drm/amdgpu: Adjust debugfs eviction and IB access permissions
+    - drm/amdgpu: prevent NULL pointer dereference if ATIF is not supported
+    - thermal/drivers/qcom/lmh: Remove false lockdep backtrace
+    - dm cache: correct the number of origin blocks to match the target length
+    - dm cache: optimize dirty bit checking with find_next_bit when resizing
+    - dm-unstriped: cast an operand to sector_t to prevent potential uint32_t
+      overflow
+    - ALSA: usb-audio: Add quirk for HP 320 FHD Webcam
+    - posix-cpu-timers: Clear TICK_DEP_BIT_POSIX_TIMER on clone
+    - io_uring: rename kiocb_end_write() local helper
+    - fs: create kiocb_{start,end}_write() helpers
+    - io_uring: use kiocb_{start,end}_write() helpers
+    - media: uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in
+      uvc_parse_format
+    - fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
+    - usb: dwc3: fix fault at system suspend if device was already runtime
+      suspended
+    - USB: serial: qcserial: add support for Sierra Wireless EM86xx
+    - USB: serial: option: add Fibocom FG132 0x0112 composition
+    - USB: serial: option: add Quectel RG650V
+    - irqchip/gic-v3: Force propagation of the active state with a read-back
+    - ucounts: fix counter leak in inc_rlimit_get_ucounts()
+    - ALSA: usb-audio: Support jack detection on Dell dock
+    - ALSA: usb-audio: Add quirks for Dell WD19 dock
+    - ACPI: PRM: Clean up guid type in struct prm_handler_info
+    - ALSA: usb-audio: Add endianness annotations
+    - Linux 5.15.172
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50265
+    - ocfs2: remove entry once instead of null-ptr-dereference in
+      ocfs2_xa_remove()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50267
+    - USB: serial: io_edgeport: fix use after free in debug printk
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50268
+    - usb: typec: fix potential out of bounds in ucsi_ccg_update_set_new_cam_cmd()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50269
+    - usb: musb: sunxi: Fix accessing an released usb phy
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50036
+    - net: do not delay dst_entries_add() in dst_release()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-42291
+    - ice: Add a per-VF limit on number of FDIR filters
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50273
+    - btrfs: reinitialize delayed ref list after deleting it from the list
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53066
+    - nfs: Fix KMSAN warning in decode_getfattr_attrs()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53052
+    - io_uring/rw: fix missing NOWAIT check for O_DIRECT start write
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50278
+    - dm cache: fix potential out-of-bounds access on the first resume
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50279
+    - dm cache: fix out-of-bounds access to the dirty bitset when resizing
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50282
+    - drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50287
+    - media: v4l2-tpg: prevent the risk of a division by zero
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50290
+    - media: cx24116: prevent overflows on SNR calculus
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53061
+    - media: s5p-jpeg: prevent buffer overflows
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50292
+    - ASoC: stm32: spdifrx: fix dma channel release in stm32_spdifrx_remove
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53063
+    - media: dvbdev: prevent the risk of out of memory access
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50295
+    - net: arc: fix the device for dma_map_single/dma_unmap_single
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50296
+    - net: hns3: fix kernel crash when uninstalling driver
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-53088
+    - i40e: fix race condition by adding filter's intermediate sync state
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50299
+    - sctp: properly validate chunk size in sctp_sf_ootb()
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50301
+    - security/keys: fix slab-out-of-bounds in key_task_permission
+  * Jammy update: v5.15.172 upstream stable release (LP: #2089533) //
+    CVE-2024-50302
+    - HID: core: zero-initialize the report buffer
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405)
+    - selftests/mm: fix incorrect buffer->mirror size in hmm2 double_map test
+    - ACPI: PRM: Remove unnecessary blank lines
+    - ACPI: PRM: Change handler_addr type to void pointer
+    - cgroup: Fix potential overflow issue when checking max_depth
+    - mac80211: MAC80211_MESSAGE_TRACING should depend on TRACING
+    - wifi: mac80211: skip non-uploaded keys in ieee80211_iter_keys
+    - wifi: brcm80211: BRCM_TRACING should depend on TRACING
+    - RDMA/cxgb4: Dump vendor specific QP details
+    - RDMA/mlx5: Round max_rd_atomic/max_dest_rd_atomic up instead of down
+    - RDMA/bnxt_re: synchronize the qp-handle table array
+    - mac80211: do drv_reconfig_complete() before restarting all
+    - mac80211: Add support to trigger sta disconnect on hardware restart
+    - wifi: iwlwifi: mvm: disconnect station vifs if recovery failed
+    - ASoC: cs42l51: Fix some error handling paths in cs42l51_probe()
+    - gtp: allow -1 to be specified as file description from userspace
+    - net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension
+    - firmware: arm_sdei: Fix the input parameter of cpuhp_remove_state()
+    - fs/ntfs3: Fix warning possible deadlock in ntfs_set_state
+    - scsi: scsi_transport_fc: Allow setting rport state to current state
+    - net: amd: mvme147: Fix probe banner message
+    - NFS: remove revoked delegation from server's delegation list
+    - misc: sgi-gru: Don't disable preemption in GRU driver
+    - usbip: tools: Fix detach_port() invalid port error path
+    - usb: phy: Fix API devm_usb_put_phy() can not release the phy
+    - usb: typec: fix unreleased fwnode_handle in typec_port_register_altmodes()
+    - xhci: Fix Link TRB DMA in command ring stopped completion event
+    - xhci: Use pm_runtime_get to prevent RPM on unsupported systems
+    - Revert "driver core: Fix uevent_show() vs driver detach race"
+    - iio: light: veml6030: fix microlux value calculation
+    - riscv: vdso: Prevent the compiler from inserting calls to memset()
+    - riscv: efi: Set NX compat flag in PE/COFF header
+    - riscv: Use '%u' to format the output of 'cpu'
+    - riscv: Remove unused GENERATING_ASM_OFFSETS
+    - riscv: Remove duplicated GET_RM
+    - mm/page_alloc: call check_new_pages() while zone spinlock is not held
+    - mm/page_alloc: fix tracepoint mm_page_alloc_zone_locked()
+    - mm/page_alloc: split out buddy removal code from rmqueue into separate
+      helper
+    - mm/page_alloc: rename ALLOC_HIGH to ALLOC_MIN_RESERVE
+    - mm/page_alloc: treat RT tasks similar to __GFP_HIGH
+    - mm/page_alloc: explicitly record high-order atomic allocations in
+      alloc_flags
+    - mm/page_alloc: explicitly define what alloc flags deplete min reserves
+    - mm/page_alloc: explicitly define how __GFP_HIGH non-blocking allocations
+      accesses reserves
+    - Revert "drm/mipi-dsi: Set the fwnode for mipi_dsi_device"
+    - vt: prevent kernel-infoleak in con_font_get()
+    - mac80211: always have ieee80211_sta_restart()
+    - Linux 5.15.171
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2023-52913
+    - drm/i915: Fix potential context UAFs
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50228
+    - mm: shmem: fix data-race in shmem_getattr()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53055
+    - wifi: iwlwifi: mvm: fix 6 GHz scan construction
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50230
+    - nilfs2: fix kernel bug due to missing clearing of checked flag
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50072
+    - x86/bugs: Use code segment selector for VERW operand
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50218
+    - ocfs2: pass u64 to ocfs2_truncate_inline maybe overflow
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50219
+    - mm/page_alloc: let GFP_ATOMIC order-0 allocs access highatomic reserves
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50229
+    - nilfs2: fix potential deadlock with newly created symlinks
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50232
+    - iio: adc: ad7124: fix division by zero in ad7124_set_channel_odr()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50233
+    - staging: iio: frequency: ad9832: fix division by zero in
+      ad9832_calc_freqreg()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50234
+    - wifi: iwlegacy: Clear stale interrupts before resuming device
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50236
+    - wifi: ath10k: Fix memory leak in management tx
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50237
+    - wifi: mac80211: do not pass a stopped vif to the driver in .get_txpower
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50244
+    - fs/ntfs3: Additional check in ni_clear()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50245
+    - fs/ntfs3: Fix possible deadlock in mi_read
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50247
+    - fs/ntfs3: Check if more than chunk-size bytes are written
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50249
+    - ACPI: CPPC: Make rmw_lock a raw_spin_lock
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50251
+    - netfilter: nft_payload: sanitize offset and length before calling
+      skb_checksum()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50257
+    - netfilter: Fix use-after-free in get_info()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50262
+    - bpf: Fix out-of-bounds write in trie_get_next_key()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50259
+    - netdevsim: Add trailing zero to terminate the string in
+      nsim_nexthop_bucket_activity_write()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53042
+    - ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_init_flow()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53058
+    - net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-53059
+    - wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50141
+    - ACPI: PRM: Find EFI_MEMORY_RUNTIME block for PRM handler and context
+  * Jammy update: v5.15.171 upstream stable release (LP: #2089405) //
+    CVE-2024-50086
+    - ksmbd: fix user-after-free from session log off
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272)
+    - RDMA/bnxt_re: Fix incorrect AVID type in WQE structure
+    - x86/resctrl: Avoid overflow in MB settings in bw_validate()
+    - ARM: dts: bcm2837-rpi-cm3-io3: Fix HDMI hpd-gpio pin
+    - RDMA/cxgb4: Fix RDMA_CM_EVENT_UNREACHABLE error for iWARP
+    - RDMA/irdma: Fix misspelling of "accept*"
+    - ipv4: give an IPv4 dev to blackhole_netdev
+    - RDMA/bnxt_re: Return more meaningful error
+    - drm/msm/dsi: fix 32-bit signed integer extension in pclk_rate calculation
+    - drm/msm: Allocate memory for disp snapshot with kvzalloc()
+    - net: usb: usbnet: fix race in probe failure
+    - octeontx2-af: Fix potential integer overflows on integer shifts
+    - macsec: don't increment counters for an unrelated SA
+    - net: ethernet: aeroflex: fix potential memory leak in
+      greth_start_xmit_gbit()
+    - net/smc: Fix searching in list of known pnetids in smc_pnet_add_pnetid
+    - net: xilinx: axienet: fix potential memory leak in axienet_start_xmit()
+    - genetlink: hold RCU in genlmsg_mcast()
+    - s390: Initialize psw mask in perf_arch_fetch_caller_regs()
+    - arm64:uprobe fix the uprobe SWBP_INSN in big-endian
+    - KVM: s390: gaccess: Check if guest address is in memslot
+    - usb: gadget: Add function wakeup support
+    - XHCI: Separate PORT and CAPs macros into dedicated file
+    - usb: dwc3: core: Fix system suspend on TI AM62 platforms
+    - block, bfq: fix procress reference leakage for bfqq in merge chain
+    - ASoC: codecs: lpass-rx-macro: add missing CDC_RX_BCL_VBAT_RF_PROC2 to
+      default regs values
+    - ASoC: fsl_sai: Enable 'FIFO continue on error' FCONT bit
+    - arm64: Force position-independent veneers
+    - platform/x86: dell-wmi: Ignore suspend notifications
+    - arm64/uprobes: change the uprobe_opcode_t typedef to fix the sparse warning
+    - ASoC: qcom: sm8250: add qrb4210-rb2-sndcard compatible string
+    - platform/x86: dell-sysman: add support for alienware products
+    - jfs: Fix sanity check in dbMount
+    - xfrm: extract dst lookup parameters into a struct
+    - xfrm: respect ip protocols rules criteria when performing dst lookups
+    - net: plip: fix break; causing plip to never transmit
+    - net: dsa: mv88e6xxx: Fix error when setting port policy on mv88e6393x
+    - net: usb: usbnet: fix name regression
+    - r8169: avoid unsolicited interrupts
+    - posix-clock: posix-clock: Fix unbalanced locking in pc_clock_settime()
+    - bpf,perf: Fix perf_event_detach_bpf_prog error handling
+    - ALSA: hda/realtek: Update default depop procedure
+    - btrfs: zoned: fix zone unusable accounting for freed reserved extent
+    - ACPI: resource: Add LG 16T90SP to irq1_level_low_skip_override[]
+    - ACPI: button: Add DMI quirk for Samsung Galaxy Book2 to fix initial lid
+      detection issue
+    - openat2: explicitly return -E2BIG for (usize > PAGE_SIZE)
+    - ALSA: hda/realtek: Add subwoofer quirk for Acer Predator G9-593
+    - hv_netvsc: Fix VF namespace also in synthetic NIC NETDEV_REGISTER event
+    - selinux: improve error checking in sel_write_load()
+    - net: phy: dp83822: Fix reset pin definitions
+    - Linux 5.15.170
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50142
+    - xfrm: validate new SA's prefixlen using SA family when sel.family is unset
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50103
+    - ASoC: qcom: Fix NULL Dereference in asoc_qcom_lpass_cpu_platform_probe()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50058
+    - serial: protect uart_port_dtr_rts() in uart_shutdown() too
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50110
+    - xfrm: fix one more kernel-infoleak in algo dumping
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50115
+    - KVM: nSVM: Ignore nCR3[4:0] when loading PDPTEs from memory
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50116
+    - nilfs2: fix kernel bug due to missing clearing of buffer delay flag
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50117
+    - drm/amd: Guard against bad data for ATIF ACPI method
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50205
+    - ALSA: firewire-lib: Avoid division by zero in apply_constraint_to_size()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50127
+    - net: sched: fix use-after-free in taprio_change()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50128
+    - net: wwan: fix global oob in wwan_rtnl_policy
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50167
+    - be2net: fix potential memory leak in be_xmit()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50168
+    - net/sun3_82586: fix potential memory leak in sun3_82586_send_packet()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50131
+    - tracing: Consider the NULL character when validating the event length
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50143
+    - udf: fix uninit-value use in udf_get_fileshortad
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50134
+    - drm/vboxvideo: Replace fake VLA at end of vbva_mouse_pointer_shape with real
+      VLA
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50010
+    - exec: don't WARN for racy path_noexec check
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50194
+    - arm64: probes: Fix uprobes for big-endian kernels
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50148
+    - Bluetooth: bnep: fix wild-memory-access in proto_unregister
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50150
+    - usb: typec: altmode should keep reference to parent
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50151
+    - smb: client: fix OOBs when building SMB2_IOCTL request
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50153
+    - scsi: target: core: Fix null-ptr-deref in target_alloc_device()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50154
+    - tcp/dccp: Don't use timer_pending() in reqsk_queue_unlink().
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50171
+    - net: systemport: fix potential memory leak in bcm_sysport_xmit()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50156
+    - drm/msm: Avoid NULL dereference in msm_disp_state_print_regs()
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50208
+    - RDMA/bnxt_re: Fix a bug while setting up Level-2 PBL pages
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50160
+    - ALSA: hda/cs8409: Fix possible NULL dereference
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50209
+    - RDMA/bnxt_re: Add a check for memory allocation
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50162
+    - bpf: devmap: provide rxq after redirect
+  * Jammy update: v5.15.170 upstream stable release (LP: #2089272) //
+    CVE-2024-50163
+    - bpf: Make sure internal and UAPI bpf_redirect flags don't overlap
+  * kernel:nft "Could not process rule: Device or resource busy" on unreferenced
+    chain (LP: #2089699)
+    - SAUCE: netfilter: nf_tables: Fix EBUSY on deleting unreferenced chain
+  * WARN in trc_wait_for_one_reader about failed IPIs (LP: #2089373)
+    - SAUCE: rcu-tasks: fix mismerge in trc_inspect_reader
+    - rcu-tasks: Idle tasks on offline CPUs are in quiescent states
+  * CVE-2024-35887
+    - ax25: fix use-after-free bugs caused by ax25_ds_del_timer
+  * CVE-2024-40965
+    - clk: Add a devm variant of clk_rate_exclusive_get()
+    - clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()
+    - i2c: lpi2c: Avoid calling clk_get_rate during transfer
+  * CVE-2024-40982
+    - ssb: Fix potential NULL pointer dereference in ssb_device_uevent()
+  * CVE-2024-41066
+    - ibmvnic: Add tx check to prevent skb leak
+  * CVE-2024-42252
+    - closures: Change BUG_ON() to WARN_ON()
+  * CVE-2024-53097
+    - mm: krealloc: Fix MTE false alarm in __do_krealloc
+  * Add list of source files to linux-buildinfo (LP: #2086606)
+    - [Packaging] Sort build dependencies alphabetically
+    - [Packaging] Add list of used source files to buildinfo package
+  * UFS: uspi->s_3apb UBSAN: shift-out-of-bounds (LP: #2087853)
+    - ufs: ufs_sb_private_info: remove unused s_{2, 3}apb fields
+  * Jammy update: v5.15.169 upstream stable release (LP: #2088231)
+    - ALSA: hda/conexant - Fix audio routing for HP EliteOne 1000 G2
+    - udf: New directory iteration code
+    - udf: Convert udf_expand_dir_adinicb() to new directory iteration
+    - udf: Move udf_expand_dir_adinicb() to its callsite
+    - udf: Implement searching for directory entry using new iteration code
+    - udf: Provide function to mark entry as deleted using new directory iteration
+      code
+    - udf: Convert udf_rename() to new directory iteration code
+    - udf: Convert udf_readdir() to new directory iteration
+    - udf: Convert udf_lookup() to use new directory iteration code
+    - udf: Convert udf_get_parent() to new directory iteration code
+    - udf: Convert empty_dir() to new directory iteration code
+    - udf: Convert udf_rmdir() to new directory iteration code
+    - udf: Convert udf_unlink() to new directory iteration code
+    - udf: Implement adding of dir entries using new iteration code
+    - udf: Convert udf_add_nondir() to new directory iteration
+    - udf: Convert udf_mkdir() to new directory iteration code
+    - udf: Convert udf_link() to new directory iteration code
+    - udf: Remove old directory iteration code
+    - udf: Handle error when expanding directory
+    - udf: Don't return bh from udf_expand_dir_adinicb()
+    - udf: Fix bogus checksum computation in udf_rename()
+    - net: enetc: remove xdp_drops statistic from enetc_xdp_drop()
+    - net: enetc: add missing static descriptor and inline keyword
+    - posix-clock: Fix missing timespec64 check in pc_clock_settime()
+    - arm64: probes: Remove broken LDR (literal) uprobe support
+    - arm64: probes: Fix simulate_ldr*_literal()
+    - net: macb: Avoid 20s boot delay by skipping MDIO bus registration for fixed-
+      link PHY
+    - irqchip/gic-v3-its: Fix VSYNC referencing an unmapped VPE on GIC v4.1
+    - fat: fix uninitialized variable
+    - mm/swapfile: skip HugeTLB pages for unuse_vma
+    - secretmem: disable memfd_secret() if arch cannot set direct map
+    - dm-crypt, dm-verity: disable tasklets
+    - KVM: Fix a data race on last_boosted_vcpu in kvm_vcpu_on_spin()
+    - drm/shmem-helper: Fix BUG_ON() on mmap(PROT_WRITE, MAP_PRIVATE)
+    - io_uring/sqpoll: do not allow pinning outside of cpuset
+    - io_uring/sqpoll: retain test for whether the CPU is valid
+    - io_uring/sqpoll: do not put cpumask on stack
+    - iommu/vt-d: Fix incorrect pci_for_each_dma_alias() for non-PCI devices
+    - s390/sclp_vt220: Convert newlines to CRLF instead of LFCR
+    - KVM: s390: Change virtual to physical address access in diag 0x258 handler
+    - x86/cpufeatures: Define X86_FEATURE_AMD_IBPB_RET
+    - x86/cpufeatures: Add a IBPB_NO_RET BUG flag
+    - x86/entry: Have entry_ibpb() invalidate return predictions
+    - x86/bugs: Skip RSB fill at VMEXIT
+    - x86/bugs: Do not use UNTRAIN_RET with IBPB on entry
+    - blk-rq-qos: fix crash on rq_qos_wait vs. rq_qos_wake_function race
+    - io_uring/sqpoll: close race on waiting for sqring entries
+    - drm/radeon: Fix encoder->possible_clones
+    - drm/vmwgfx: Handle surface check failure correctly
+    - iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
+    - iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
+    - iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
+    - iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - iio: hid-sensors: Fix an error handling path in
+      _hid_sensor_set_report_latency()
+    - iio: light: veml6030: fix ALS sensor resolution
+    - iio: light: veml6030: fix IIO device retrieval from embedded device
+    - iio: light: opt3001: add missing full-scale range value
+    - iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - iio: adc: ti-ads124s08: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
+    - Bluetooth: Remove debugfs directory on module init failure
+    - Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001
+    - xhci: Fix incorrect stream context type macro
+    - xhci: Mitigate failed set dequeue pointer commands
+    - USB: serial: option: add support for Quectel EG916Q-GL
+    - USB: serial: option: add Telit FN920C04 MBIM compositions
+    - parport: Proper fix for array out-of-bounds access
+    - x86/resctrl: Annotate get_mem_config() functions as __init
+    - x86/apic: Always explicitly disarm TSC-deadline timer
+    - x86/entry_32: Do not clobber user EFLAGS.ZF
+    - x86/entry_32: Clear CPU buffers after register restore in NMI return
+    - pinctrl: ocelot: fix system hang on level based interrupts
+    - irqchip/gic-v4: Don't allow a VMOVP on a dying VPE
+    - mptcp: track and update contiguous data status
+    - mptcp: handle consistently DSS corruption
+    - tcp: fix mptcp DSS corruption due to large pmtu xmit
+    - mptcp: fallback when MPTCP opts are dropped after 1st data
+    - mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow
+    - mptcp: prevent MPC handshake on port-based signal endpoints
+    - nilfs2: propagate directory read errors from nilfs_find_entry()
+    - powerpc/mm: Always update max/min_low_pfn in mem_topology_setup()
+    - ALSA: hda/conexant - Use cached pin control for Node 0x1d on HP EliteOne
+      1000 G2
+    - Linux 5.15.169
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Mon, 17 Feb 2025 16:56:19 +0800
+
+linux-xilinx-zynqmp (5.15.0-1042.46) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1042.46 -proposed tracker (LP: #2093570)
+
+  * Add list of source files to linux-buildinfo (LP: #2086606)
+    - [Packaging] Add dwarfdump package in the Build-Depends
+
+  [ Ubuntu: 5.15.0-131.141 ]
+
+  * jammy/linux: 5.15.0-131.141 -proposed tracker (LP: #2093573)
+  * CVE-2024-53164
+    - net: sched: fix ordering of qlen adjustment
+  * CVE-2024-53141
+    - netfilter: ipset: add missing range check in bitmap_ip_uadt
+  * CVE-2024-53103
+    - hv_sock: Initializing vsk->trans to NULL to prevent a dangling pointer
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 24 Jan 2025 21:08:48 +0800
+
+linux-xilinx-zynqmp (5.15.0-1041.45) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1041.45 -proposed tracker (LP: #2092128)
+
+  [ Ubuntu: 5.15.0-130.140 ]
+
+  * jammy/linux: 5.15.0-130.140 -proposed tracker (LP: #2092132)
+  * ovs/linuxbridge jobs running on ubuntu jammy broken with latest kernel
+    5.15.0-127.137 (LP: #2091990)
+    - netfilter: xtables: fix typo causing some targets not to load on IPv6
+
+  [ Ubuntu: 5.15.0-128.138 ]
+
+  * jammy/linux: 5.15.0-128.138 -proposed tracker (LP: #2090163)
+  * CVE-2024-50264
+    - vsock/virtio: Initialization of the dangling pointer occurring in vsk->trans
+  * CVE-2024-53057
+    - net/sched: stop qdisc_tree_reduce_backlog on TC_H_ROOT
+  * CVE-2024-43904
+    - drm/amd/display: Add null checks for 'stream' and 'plane' before
+      dereferencing
+  * CVE-2024-40973
+    - media: mtk-vcodec: potential null pointer deference in SCP
+  * CVE-2024-38553
+    - net: fec: remove .ndo_poll_controller to avoid deadlocks
+  * CVE-2024-26822
+    - smb: client: set correct id, uid and cruid for multiuser automounts
+  * CVE-2020-12351 // CVE-2020-12352 // CVE-2020-24490
+    - [Config] Disable BlueZ highspeed support
+  * CVE-2024-40910
+    - ax25: Fix refcount imbalance on inbound connections
+  * CVE-2024-35963
+    - Bluetooth: hci_sock: Fix not validating setsockopt user input
+  * CVE-2024-35965
+    - Bluetooth: L2CAP: Fix not validating setsockopt user input
+  * CVE-2024-35966
+    - Bluetooth: RFCOMM: Fix not validating setsockopt user input
+  * CVE-2024-35967
+    - Bluetooth: SCO: Fix not validating setsockopt user input
+
+ -- Wei-Lin Chang <weilin.chang@canonical.com>  Fri, 20 Dec 2024 11:23:20 +0800
+
+linux-xilinx-zynqmp (5.15.0-1039.43) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1039.43 -proposed tracker
+    (LP: #2086354)
+
+  [ Ubuntu: 5.15.0-127.137 ]
+
+  * jammy/linux: 5.15.0-127.137 -proposed tracker (LP: #2086357)
+  * Jammy update: v5.15.168 upstream stable release (LP: #2086242)
+    - parisc: Fix 64-bit userspace syscall path
+    - parisc: Fix stack start for ADDR_NO_RANDOMIZE personality
+    - of/irq: Support #msi-cells=<0> in of_msi_get_domain
+    - drm: omapdrm: Add missing check for alloc_ordered_workqueue
+    - jbd2: stop waiting for space when jbd2_cleanup_journal_tail() returns error
+    - jbd2: correctly compare tids with tid_geq function in jbd2_fc_begin_commit
+    - mm: krealloc: consider spare memory for __GFP_ZERO
+    - ocfs2: fix the la space leak when unmounting an ocfs2 volume
+    - ocfs2: fix uninit-value in ocfs2_get_block()
+    - ocfs2: reserve space for inline xattr before attaching reflink tree
+    - ocfs2: cancel dqi_sync_work before freeing oinfo
+    - ocfs2: remove unreasonable unlock in ocfs2_read_blocks
+    - ocfs2: fix null-ptr-deref when journal load failed.
+    - ocfs2: fix possible null-ptr-deref in ocfs2_set_buffer_uptodate
+    - usbnet: ipheth: fix carrier detection in modes 1 and 4
+    - net: ethernet: use ip_hdrlen() instead of bit shift
+    - net: phy: vitesse: repair vsc73xx autonegotiation
+    - powerpc/mm: Fix boot warning with hugepages and CONFIG_DEBUG_VIRTUAL
+    - btrfs: update target inode's ctime on unlink
+    - Input: ads7846 - ratelimit the spi_sync error message
+    - Input: synaptics - enable SMBus for HP Elitebook 840 G2
+    - HID: multitouch: Add support for GT7868Q
+    - scripts: kconfig: merge_config: config files: add a trailing newline
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Go 3
+    - drm/msm/adreno: Fix error return if missing firmware-name
+    - Input: i8042 - add Fujitsu Lifebook E756 to i8042 quirk table
+    - NFSv4: Fix clearing of layout segments in layoutreturn
+    - NFS: Avoid unnecessary rescanning of the per-server delegation list
+    - platform/x86: panasonic-laptop: Fix SINF array out of bounds accesses
+    - platform/x86: panasonic-laptop: Allocate 1 entry extra in the sinf array
+    - mptcp: pm: Fix uaf in __timer_delete_sync
+    - arm64: dts: rockchip: override BIOS_DISABLE signal via GPIO hog on RK3399
+      Puma
+    - minmax: reduce min/max macro expansion in atomisp driver
+    - net: tighten bad gso csum offset check in virtio_net_hdr
+    - mm: avoid leaving partial pfn mappings around in error case
+    - fs/ntfs3: Use kvfree to free memory allocated by kvmalloc
+    - arm64: dts: rockchip: fix PMIC interrupt pin in pinctrl for ROCK Pi E
+    - eeprom: digsy_mtc: Fix 93xx46 driver probe failure
+    - selftests/bpf: Support SOCK_STREAM in unix_inet_redir_to_connected()
+    - hwmon: (pmbus) Introduce and use write_byte_data callback
+    - hwmon: (pmbus) Conditionally clear individual status bits for pmbus rev >=
+      1.2
+    - ice: fix accounting for filters shared by multiple VSIs
+    - igb: Always call igb_xdp_ring_update_tail() under Tx lock
+    - net/mlx5e: Add missing link modes to ptys2ethtool_map
+    - net/mlx5: Explicitly set scheduling element and TSAR type
+    - net/mlx5: Add support to create match definer
+    - net/mlx5: Add IFC bits and enums for flow meter
+    - net/mlx5: Add missing masks and QoS bit masks for scheduling elements
+    - fou: fix initialization of grc
+    - octeontx2-af: Set XOFF on other child transmit schedulers during SMQ flush
+    - octeontx2-af: Modify SMQ flush sequence to drop packets
+    - net: ftgmac100: Enable TX interrupt to avoid TX timeout
+    - netfilter: nft_socket: fix sk refcount leaks
+    - net: dpaa: Pad packets to ETH_ZLEN
+    - spi: nxp-fspi: fix the KASAN report out-of-bounds bug
+    - dma-buf: heaps: Fix off-by-one in CMA heap fault handler
+    - ASoC: meson: axg-card: fix 'use-after-free'
+    - ASoC: allow module autoloading for table db1200_pids
+    - ALSA: hda/realtek - Fixed ALC256 headphone no sound
+    - ALSA: hda/realtek - FIxed ALC285 headphone no sound
+    - scsi: lpfc: Fix overflow build issue
+    - pinctrl: at91: make it work with current gpiolib
+    - microblaze: don't treat zero reserved memory regions as error
+    - net: ftgmac100: Ensure tx descriptor updates are visible
+    - wifi: iwlwifi: lower message level for FW buffer destination
+    - wifi: iwlwifi: mvm: fix iwl_mvm_scan_fits() calculation
+    - wifi: iwlwifi: mvm: pause TCM when the firmware is stopped
+    - wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead
+    - wifi: iwlwifi: clear trans->state earlier upon error
+    - ASoC: intel: fix module autoloading
+    - ASoC: tda7419: fix module autoloading
+    - spi: spidev: Add an entry for elgin,jg10309-01
+    - drm: komeda: Fix an issue related to normalized zpos
+    - spi: bcm63xx: Enable module autoloading
+    - x86/hyperv: Set X86_FEATURE_TSC_KNOWN_FREQ when Hyper-V provides frequency
+    - spi: spidev: Add missing spi_device_id for jg10309-01
+    - ocfs2: add bounds checking to ocfs2_xattr_find_entry()
+    - ocfs2: strict bound check before memcmp in ocfs2_xattr_find_entry()
+    - cgroup: Make operations on the cgroup root_list RCU safe
+    - Revert "wifi: cfg80211: check wiphy mutex is held for wdev mutex"
+    - gpio: prevent potential speculation leaks in gpio_device_get_desc()
+    - gpiolib: cdev: Ignore reconfiguration without direction
+    - cgroup: Move rcu_head up near the top of cgroup_root
+    - USB: serial: pl2303: add device id for Macrosilicon MS3020
+    - USB: usbtmc: prevent kernel-usb-infoleak
+    - EDAC/synopsys: Add support for version 3 of the Synopsys EDAC DDR
+    - EDAC/synopsys: Use the correct register to disable the error interrupt on v3
+      hw
+    - EDAC/synopsys: Re-enable the error interrupts on v3 hw
+    - EDAC/synopsys: Fix ECC status and IRQ control race condition
+    - EDAC/synopsys: Fix error injection on Zynq UltraScale+
+    - wifi: rtw88: always wait for both firmware loading attempts
+    - crypto: xor - fix template benchmarking
+    - ACPI: PMIC: Remove unneeded check in tps68470_pmic_opregion_probe()
+    - wifi: ath9k: fix parameter check in ath9k_init_debug()
+    - wifi: ath9k: Remove error checks when creating debugfs entries
+    - net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
+    - wifi: rtw88: remove CPT execution branch never used
+    - fs: explicitly unregister per-superblock BDIs
+    - mount: warn only once about timestamp range expiration
+    - fs/namespace: fnic: Switch to use %ptTd
+    - mount: handle OOM on mnt_warn_timestamp_expiry
+    - wifi: iwlwifi: mvm: increase the time between ranging measurements
+    - padata: Honor the caller's alignment in case of chunk_size 0
+    - can: j1939: use correct function name in comment
+    - ACPI: CPPC: Fix MASK_VAL() usage
+    - netfilter: nf_tables: elements with timeout below CONFIG_HZ never expire
+    - netfilter: nf_tables: reject element expiration with no timeout
+    - netfilter: nf_tables: reject expiration higher than timeout
+    - netfilter: nf_tables: remove annotation to access set timeout while holding
+      lock
+    - cpufreq: ti-cpufreq: Introduce quirks to handle syscon fails appropriately
+    - x86/sgx: Fix deadlock in SGX NUMA node search
+    - wifi: cfg80211: fix UBSAN noise in cfg80211_wext_siwscan()
+    - wifi: mt76: mt7915: fix rx filter setting for bfee functionality
+    - wifi: cfg80211: fix two more possible UBSAN-detected off-by-one errors
+    - wifi: mac80211: use two-phase skb reclamation in ieee80211_do_stop()
+    - wifi: wilc1000: fix potential RCU dereference issue in
+      wilc_parse_join_bss_param
+    - sock_map: Add a cond_resched() in sock_hash_free()
+    - can: bcm: Clear bo->bcm_proc_read after remove_proc_entry().
+    - can: m_can: m_can_close(): stop clocks after device has been shut down
+    - Bluetooth: btusb: Fix not handling ZPL/short-transfer
+    - bareudp: Pull inner IP header in bareudp_udp_encap_recv().
+    - net: geneve: support IPv4/IPv6 as inner protocol
+    - geneve: Fix incorrect inner network header offset when innerprotoinherit is
+      set
+    - bareudp: Pull inner IP header on xmit.
+    - net: enetc: Use IRQF_NO_AUTOEN flag in request_irq()
+    - r8169: disable ALDPS per default for RTL8125
+    - net: ipv6: rpl_iptunnel: Fix memory leak in rpl_input
+    - net: tipc: avoid possible garbage value
+    - block, bfq: fix possible UAF for bfqq->bic with merge chain
+    - block, bfq: choose the last bfqq from merge chain in bfq_setup_cooperator()
+    - block, bfq: don't break merge chain in bfq_split_bfqq()
+    - block: print symbolic error name instead of error code
+    - block: fix potential invalid pointer dereference in blk_add_partition
+    - spi: ppc4xx: handle irq_of_parse_and_map() errors
+    - spi: ppc4xx: Avoid returning 0 when failed to parse and map IRQ
+    - arm64: dts: renesas: r9a07g044: Correct GICD and GICR sizes
+    - ARM: dts: microchip: sam9x60: Fix rtc/rtt clocks
+    - ARM: dts: imx7d-zii-rmu2: fix Ethernet PHY pinctrl property
+    - ARM: versatile: fix OF node leak in CPUs prepare
+    - reset: berlin: fix OF node leak in probe() error path
+    - reset: k210: fix OF node leak in probe() error path
+    - clocksource/drivers/qcom: Add missing iounmap() on errors in
+      msm_dt_timer_init()
+    - m68k: Fix kernel_clone_args.flags in m68k_clone()
+    - hwmon: (max16065) Fix overflows seen when writing limits
+    - i2c: Add i2c_get_match_data()
+    - hwmon: (max16065) Remove use of i2c_match_id()
+    - hwmon: (max16065) Fix alarm attributes
+    - mtd: slram: insert break after errors in parsing the map
+    - hwmon: (ntc_thermistor) fix module autoloading
+    - power: supply: axp20x_battery: Remove design from min and max voltage
+    - power: supply: max17042_battery: Fix SOC threshold calc w/ no current sense
+    - fbdev: hpfb: Fix an error handling path in hpfb_dio_probe()
+    - mtd: powernv: Add check devm_kasprintf() returned value
+    - pmdomain: core: Harden inter-column space in debug summary
+    - drm/stm: Fix an error handling path in stm_drm_platform_probe()
+    - drm/amd/display: Add null check for set_output_gamma in
+      dcn30_set_output_transfer_func
+    - drm/amdgpu: Replace one-element array with flexible-array member
+    - drm/amdgpu: properly handle vbios fake edid sizing
+    - drm/radeon: Replace one-element array with flexible-array member
+    - drm/radeon: properly handle vbios fake edid sizing
+    - scsi: NCR5380: Add SCp members to struct NCR5380_cmd
+    - scsi: NCR5380: Check for phase match during PDMA fixup
+    - drm/rockchip: vop: Allow 4096px width scaling
+    - drm/rockchip: dw_hdmi: Fix reading EDID when using a forced mode
+    - drm/radeon/evergreen_cs: fix int overflow errors in cs track offsets
+    - drm/bridge: lontium-lt8912b: Validate mode in drm_bridge_funcs::mode_valid()
+    - scsi: elx: libefc: Fix potential use after free in efc_nport_vport_del()
+    - jfs: fix out-of-bounds in dbNextAG() and diAlloc()
+    - drm/mediatek: Use spin_lock_irqsave() for CRTC event lock
+    - powerpc/32: Remove the 'nobats' kernel parameter
+    - powerpc/32: Remove 'noltlbs' kernel parameter
+    - powerpc/8xx: Fix initial memory mapping
+    - powerpc/8xx: Fix kernel vs user address comparison
+    - drm/msm: Fix incorrect file name output in adreno_request_fw()
+    - drm/msm/a5xx: disable preemption in submits by default
+    - drm/msm/a5xx: properly clear preemption records on resume
+    - drm/msm/a5xx: fix races in preemption evaluation stage
+    - drm/msm: Drop priv->lastctx
+    - drm/msm/a5xx: workaround early ring-buffer emptiness check
+    - ipmi: docs: don't advertise deprecated sysfs entries
+    - drm/msm: fix %s null argument error
+    - drivers:drm:exynos_drm_gsc:Fix wrong assignment in gsc_bind()
+    - xen: use correct end address of kernel for conflict checking
+    - xen/swiotlb: add alignment check for dma buffers
+    - tpm: Clean up TPM space after command failure
+    - selftests/bpf: Fix compile error from rlim_t in sk_storage_map.c
+    - selftests/bpf: Fix error compiling bpf_iter_setsockopt.c with musl libc
+    - selftests/bpf: Fix missing ARRAY_SIZE() definition in bench.c
+    - selftests/bpf: Fix compiling kfree_skb.c with musl-libc
+    - selftests/bpf: Fix compiling flow_dissector.c with musl-libc
+    - selftests/bpf: Fix compiling tcp_rtt.c with musl-libc
+    - selftests/bpf: Fix compiling core_reloc.c with musl-libc
+    - selftests/bpf: Fix errors compiling cg_storage_multi.h with musl libc
+    - selftests/bpf: Fix error compiling test_lru_map.c
+    - selftests/bpf: Fix C++ compile error from missing _Bool type
+    - xz: cleanup CRC32 edits from 2018
+    - kthread: fix task state in kthread worker if being frozen
+    - ext4: clear EXT4_GROUP_INFO_WAS_TRIMMED_BIT even mount with discard
+    - smackfs: Use rcu_assign_pointer() to ensure safe assignment in smk_set_cipso
+    - ext4: avoid buffer_head leak in ext4_mark_inode_used()
+    - ext4: avoid potential buffer_head leak in __ext4_new_inode()
+    - ext4: avoid negative min_clusters in find_group_orlov()
+    - ext4: return error on ext4_find_inline_entry
+    - ext4: avoid OOB when system.data xattr changes underneath the filesystem
+    - nilfs2: fix potential null-ptr-deref in nilfs_btree_insert()
+    - nilfs2: determine empty node blocks as corrupted
+    - nilfs2: fix potential oob read in nilfs_btree_check_delete()
+    - bpf: Fix bpf_strtol and bpf_strtoul helpers for 32bit
+    - perf mem: Free the allocated sort string, fixing a leak
+    - perf sched timehist: Fix missing free of session in perf_sched__timehist()
+    - perf sched timehist: Fixed timestamp error when unable to confirm event
+      sched_in time
+    - perf time-utils: Fix 32-bit nsec parsing
+    - clk: imx: imx8mp: fix clock tree update of TF-A managed clocks
+    - clk: imx: imx8qxp: Register dc0_bypass0_clk before disp clk
+    - clk: imx: imx8qxp: Parent should be initialized earlier than the clock
+    - remoteproc: imx_rproc: Correct ddr alias for i.MX8M
+    - remoteproc: imx_rproc: Initialize workqueue earlier
+    - clk: rockchip: Set parent rate for DCLK_VOP clock on RK3228
+    - Input: ilitek_ts_i2c - avoid wrong input subsystem sync
+    - Input: ilitek_ts_i2c - add report id message validation
+    - drivers: media: dvb-frontends/rtl2832: fix an out-of-bounds write error
+    - drivers: media: dvb-frontends/rtl2830: fix an out-of-bounds write error
+    - PCI: keystone: Fix if-statement expression in ks_pcie_quirk()
+    - PCI: xilinx-nwl: Fix register misspelling
+    - PCI: xilinx-nwl: Clean up clock on probe failure/removal
+    - RDMA/iwcm: Fix WARNING:at_kernel/workqueue.c:#check_flush_dependency
+    - pinctrl: single: fix missing error code in pcs_probe()
+    - RDMA/rtrs: Reset hb_missed_cnt after receiving other traffic from peer
+    - RDMA/rtrs-clt: Reset cid to con_num - 1 to stay in bounds
+    - clk: ti: dra7-atl: Fix leak of of_nodes
+    - nfsd: remove unneeded EEXIST error check in nfsd_do_file_acquire
+    - nfsd: fix refcount leak when file is unhashed after being found
+    - pinctrl: mvebu: Use devm_platform_get_and_ioremap_resource()
+    - pinctrl: mvebu: Fix devinit_dove_pinctrl_probe function
+    - IB/core: Fix ib_cache_setup_one error flow cleanup
+    - watchdog: imx_sc_wdt: Don't disable WDT in suspend
+    - RDMA/hns: Don't modify rq next block addr in HIP09 QPC
+    - RDMA/hns: Fix the overflow risk of hem_list_calc_ba_range()
+    - RDMA/hns: Fix spin_unlock_irqrestore() called with IRQs enabled
+    - RDMA/hns: Remove unused abnormal interrupt of type RAS
+    - RDMA/hns: Fix the wrong type of return value of the interrupt handler
+    - RDMA/hns: Refactor the abnormal interrupt handler function
+    - RDMA/hns: Fix VF triggering PF reset in abnormal interrupt handler
+    - RDMA/hns: Optimize hem allocation performance
+    - riscv: Fix fp alignment bug in perf_callchain_user()
+    - RDMA/cxgb4: Added NULL check for lookup_atid
+    - RDMA/irdma: fix error message in irdma_modify_qp_roce()
+    - ntb: intel: Fix the NULL vs IS_ERR() bug for debugfs_create_dir()
+    - ntb_perf: Fix printk format
+    - nfsd: call cache_put if xdr_reserve_space returns NULL
+    - nfsd: return -EINVAL when namelen is 0
+    - f2fs: fix typo
+    - f2fs: fix to update i_ctime in __f2fs_setxattr()
+    - f2fs: remove unneeded check condition in __f2fs_setxattr()
+    - f2fs: reduce expensive checkpoint trigger frequency
+    - f2fs: optimize error handling in redirty_blocks
+    - f2fs: fix to wait page writeback before setting gcing flag
+    - f2fs: introduce F2FS_IPU_HONOR_OPU_WRITE ipu policy
+    - f2fs: clean up w/ dotdot_name
+    - f2fs: get rid of online repaire on corrupted directory
+    - spi: lpspi: Silence error message upon deferred probe
+    - spi: lpspi: release requested DMA channels
+    - spi: spi-fsl-lpspi: Undo runtime PM changes at driver exit time
+    - iio: adc: ad7606: fix oversampling gpio array
+    - iio: adc: ad7606: fix standby gpio state to match the documentation
+    - coresight: tmc: sg: Do not leak sg_table
+    - interconnect: qcom: sm8250: Enable sync_state
+    - vdpa: Add eventfd for the vdpa callback
+    - vhost_vdpa: assign irq bypass producer token correctly
+    - Revert "dm: requeue IO if mapping table not yet available"
+    - net: axienet: Clean up device used for DMA calls
+    - net: axienet: Clean up DMA start/stop and error handling
+    - net: axienet: don't set IRQ timer when IRQ delay not used
+    - net: axienet: implement NAPI and GRO receive
+    - net: axienet: reduce default RX interrupt threshold to 1
+    - net: axienet: add coalesce timer ethtool configuration
+    - net: axienet: Be more careful about updating tx_bd_tail
+    - net: axienet: Use NAPI for TX completion path
+    - net: axienet: Switch to 64-bit RX/TX statistics
+    - net: xilinx: axienet: Fix packet counting
+    - netfilter: nf_reject_ipv6: fix nf_reject_ip6_tcphdr_put()
+    - net: seeq: Fix use after free vulnerability in ether3 Driver Due to Race
+      Condition
+    - net: ipv6: select DST_CACHE from IPV6_RPL_LWTUNNEL
+    - tcp: check skb is non-NULL in tcp_rto_delta_us()
+    - net: qrtr: Update packets cloning when broadcasting
+    - bonding: Fix unnecessary warnings and logs from bond_xdp_get_xmit_slave()
+    - netfilter: nf_tables: Keep deleted flowtable hooks until after RCU
+    - netfilter: ctnetlink: compile ctnetlink_label_size with
+      CONFIG_NF_CONNTRACK_EVENTS
+    - drm/amd/display: Fix Synaptics Cascaded Panamera DSC Determination
+    - Input: goodix - use the new soc_intel_is_byt() helper
+    - powercap: RAPL: fix invalid initialization for pl4_supported field
+    - x86/mm: Switch to new Intel CPU model defines
+    - vfio/pci: fix potential memory leak in vfio_intx_enable()
+    - selinux,smack: don't bypass permissions check in inode_setsecctx hook
+    - Remove *.orig pattern from .gitignore
+    - PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
+    - ASoC: rt5682: Return devm_of_clk_add_hw_provider to transfer the error
+    - soc: versatile: integrator: fix OF node leak in probe() error path
+    - Revert "media: tuners: fix error return code of
+      hybrid_tuner_request_state()"
+    - Input: i8042 - add TUXEDO Stellaris 16 Gen5 AMD to i8042 quirk table
+    - Input: i8042 - add TUXEDO Stellaris 15 Slim Gen6 AMD to i8042 quirk table
+    - Input: i8042 - add another board name for TUXEDO Stellaris Gen5 AMD line
+    - drm/amd/display: Round calculated vtotal
+    - drm/amd/display: Validate backlight caps are sane
+    - scsi: mac_scsi: Revise printk(KERN_DEBUG ...) messages
+    - scsi: mac_scsi: Refactor polling loop
+    - scsi: mac_scsi: Disallow bus errors during PDMA send
+    - usbnet: fix cyclical race on disconnect with work queue
+    - USB: appledisplay: close race between probe and completion handler
+    - USB: misc: cypress_cy7c63: check for short transfer
+    - USB: class: CDC-ACM: fix race between get_serial and set_serial
+    - usb: cdnsp: Fix incorrect usb_request status
+    - usb: dwc2: drd: fix clock gating on USB role switch
+    - bus: integrator-lm: fix OF node leak in probe()
+    - firmware_loader: Block path traversal
+    - tty: rp2: Fix reset with non forgiving PCIe host bridges
+    - xhci: Set quirky xHC PCI hosts to D3 _after_ stopping and freeing them.
+    - crypto: ccp - Properly unregister /dev/sev on sev PLATFORM_STATUS failure
+    - drbd: Fix atomicity violation in drbd_uuid_set_bm()
+    - drbd: Add NULL check for net_conf to prevent dereference in state validation
+    - ACPI: sysfs: validate return type of _STR method
+    - ACPI: resource: Add another DMI match for the TongFang GMxXGxx
+    - efistub/tpm: Use ACPI reclaim memory for event log to avoid corruption
+    - perf/x86/intel/pt: Fix sampling synchronization
+    - wifi: rtw88: 8822c: Fix reported RX band width
+    - wifi: mt76: mt7615: check devm_kasprintf() returned value
+    - debugobjects: Fix conditions in fill_pool()
+    - f2fs: prevent possible int overflow in dir_block_index()
+    - f2fs: avoid potential int overflow in sanity_check_area_boundary()
+    - hwrng: mtk - Use devm_pm_runtime_enable
+    - hwrng: bcm2835 - Add missing clk_disable_unprepare in bcm2835_rng_init
+    - hwrng: cctrng - Add missing clk_disable_unprepare in cctrng_resume
+    - arm64: dts: rockchip: Raise Pinebook Pro's panel backlight PWM frequency
+    - arm64: dts: rockchip: Correct the Pinebook Pro battery design capacity
+    - vfs: fix race between evice_inodes() and find_inode()&iput()
+    - fs: Fix file_set_fowner LSM hook inconsistencies
+    - nfs: fix memory leak in error path of nfs4_do_reclaim
+    - EDAC/igen6: Fix conversion of system address to physical memory address
+    - padata: use integer wrap around to prevent deadlock on seq_nr overflow
+    - soc: versatile: realview: fix memory leak during device remove
+    - soc: versatile: realview: fix soc_dev leak during device remove
+    - usb: yurex: Replace snprintf() with the safer scnprintf() variant
+    - USB: misc: yurex: fix race between read and write
+    - xhci: fix event ring segment table related masks and variables in header
+    - xhci: remove xhci_test_trb_in_td_math early development check
+    - xhci: Refactor interrupter code for initial multi interrupter support.
+    - xhci: Preserve RsvdP bits in ERSTBA register correctly
+    - xhci: Add a quirk for writing ERST in high-low order
+    - usb: xhci: fix loss of data on Cadence xHC
+    - pps: remove usage of the deprecated ida_simple_xx() API
+    - pps: add an error check in parport_attach
+    - x86/idtentry: Incorporate definitions/declarations of the FRED entries
+    - x86/entry: Remove unwanted instrumentation in common_interrupt()
+    - bpf: lsm: Set bpf_lsm_blob_sizes.lbs_task to 0
+    - lockdep: fix deadlock issue between lockdep and rcu
+    - mm: only enforce minimum stack gap size if it's sensible
+    - i2c: aspeed: Update the stop sw state when the bus recovery occurs
+    - i2c: isch: Add missed 'else'
+    - usb: yurex: Fix inconsistent locking bug in yurex_read()
+    - spi: lpspi: Simplify some error message
+    - static_call: Handle module init failure correctly in
+      static_call_del_module()
+    - static_call: Replace pointless WARN_ON() in static_call_module_notify()
+    - mailbox: rockchip: fix a typo in module autoloading
+    - mailbox: bcm2835: Fix timeout during suspend mode
+    - ceph: remove the incorrect Fw reference check when dirtying pages
+    - ieee802154: Fix build error
+    - net/mlx5: Fix error path in multi-packet WQE transmit
+    - net/mlx5: Added cond_resched() to crdump collection
+    - net/mlx5e: Fix NULL deref in mlx5e_tir_builder_alloc()
+    - netfilter: uapi: NFTA_FLOWTABLE_HOOK is NLA_NESTED
+    - net: ieee802154: mcr20a: Use IRQF_NO_AUTOEN flag in request_irq()
+    - netfilter: nf_tables: prevent nf_skb_duplicated corruption
+    - Bluetooth: btmrvl: Use IRQF_NO_AUTOEN flag in request_irq()
+    - net: ethernet: lantiq_etop: fix memory disclosure
+    - net: avoid potential underflow in qdisc_pkt_len_init() with UFO
+    - net: add more sanity checks to qdisc_pkt_len_init()
+    - stmmac_pci: Fix underflow size in stmmac_rx
+    - net: stmmac: Disable automatic FCS/Pad stripping
+    - net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check
+    - ipv4: ip_gre: Fix drops of small packets in ipgre_xmit
+    - ppp: do not assume bh is held in ppp_channel_bridge_input()
+    - sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
+    - i2c: xiic: Fix broken locking on tx_msg
+    - i2c: xiic: Switch from waitqueue to completion
+    - i2c: xiic: Fix RX IRQ busy check
+    - i2c: xiic: xiic_xfer(): Fix runtime PM leak on error path
+    - i2c: xiic: improve error message when transfer fails to start
+    - i2c: xiic: Try re-initialization on bus busy timeout
+    - media: usbtv: Remove useless locks in usbtv_video_free()
+    - ALSA: mixer_oss: Remove some incorrect kfree_const() usages
+    - ALSA: hda/realtek: Fix the push button function for the ALC257
+    - ALSA: hda/generic: Unconditionally prefer preferred_dacs pairs
+    - ASoC: imx-card: Set card.owner to avoid a warning calltrace if SND=m
+    - ALSA: hda/conexant: Fix conflicting quirk for System76 Pangolin
+    - f2fs: Require FMODE_WRITE for atomic write ioctls
+    - wifi: ath9k: fix possible integer overflow in ath9k_get_et_stats()
+    - wifi: ath9k_htc: Use __skb_set_length() for resetting urb before resubmit
+    - ice: Adjust over allocation of memory in ice_sched_add_root_node() and
+      ice_sched_add_node()
+    - net/xen-netback: prevent UAF in xenvif_flush_hash()
+    - net: hisilicon: hip04: fix OF node leak in probe()
+    - net: hisilicon: hns_dsaf_mac: fix OF node leak in hns_mac_get_info()
+    - net: hisilicon: hns_mdio: fix OF node leak in probe()
+    - ACPI: PAD: fix crash in exit_round_robin()
+    - ACPICA: Fix memory leak if acpi_ps_get_next_namepath() fails
+    - ACPICA: Fix memory leak if acpi_ps_get_next_field() fails
+    - net: sched: consistently use rcu_replace_pointer() in taprio_change()
+    - blk_iocost: fix more out of bound shifts
+    - nvme-pci: qdepth 1 quirk
+    - wifi: ath11k: fix array out-of-bound access in SoC stats
+    - wifi: rtw88: select WANT_DEV_COREDUMP
+    - ACPI: EC: Do not release locks during operation region accesses
+    - ACPICA: check null return of ACPI_ALLOCATE_ZEROED() in
+      acpi_db_convert_to_package()
+    - tipc: guard against string buffer overrun
+    - net: mvpp2: Increase size of queue_name buffer
+    - ipv4: Check !in_dev earlier for ioctl(SIOCSIFADDR).
+    - ipv4: Mask upper DSCP bits and ECN bits in NETLINK_FIB_LOOKUP family
+    - net: atlantic: Avoid warning about potential string truncation
+    - tcp: avoid reusing FIN_WAIT2 when trying to find port in connect() process
+    - ACPICA: iasl: handle empty connection_node
+    - proc: add config & param to block forcing mem writes
+    - [Config] updateconfigs to select PROC_MEM_ALWAYS_FORCE
+    - wifi: mt76: mt7915: hold dev->mt76.mutex while disabling tx worker
+    - wifi: mwifiex: Fix memcpy() field-spanning write warning in
+      mwifiex_cmd_802_11_scan_ext()
+    - nfp: Use IRQF_NO_AUTOEN flag in request_irq()
+    - signal: Replace BUG_ON()s
+    - ALSA: usb-audio: Add input value sanity checks for standard types
+    - x86/ioapic: Handle allocation failures gracefully
+    - ALSA: usb-audio: Define macros for quirk table entries
+    - ALSA: usb-audio: Add logitech Audio profile quirk
+    - tools/x86/kcpuid: Protect against faulty "max subleaf" values
+    - ALSA: asihpi: Fix potential OOB array access
+    - ALSA: hdsp: Break infinite MIDI input flush loop
+    - x86/syscall: Avoid memcpy() for ia32 syscall_get_arguments()
+    - fbdev: pxafb: Fix possible use after free in pxafb_task()
+    - rcuscale: Provide clear error when async specified without primitives
+    - iommu/arm-smmu-qcom: hide last LPASS SMMU context bank from linux
+    - power: reset: brcmstb: Do not go into infinite loop if reset fails
+    - iommu/vt-d: Always reserve a domain ID for identity setup
+    - iommu/vt-d: Fix potential lockup if qi_submit_sync called with 0 count
+    - drm/amd/display: Add null check for top_pipe_to_program in
+      commit_planes_for_stream
+    - ata: sata_sil: Rename sil_blacklist to sil_quirks
+    - drm/amd/display: Check null pointers before using dc->clk_mgr
+    - jfs: UBSAN: shift-out-of-bounds in dbFindBits
+    - jfs: Fix uaf in dbFreeBits
+    - jfs: check if leafidx greater than num leaves per dmap tree
+    - scsi: smartpqi: correct stream detection
+    - jfs: Fix uninit-value access of new_ea in ea_buffer
+    - drm/amdgpu: add raven1 gfxoff quirk
+    - drm/amdgpu: enable gfxoff quirk on HP 705G4
+    - HID: multitouch: Add support for Thinkpad X12 Gen 2 Kbd Portfolio
+    - platform/x86: touchscreen_dmi: add nanote-next quirk
+    - drm/amd/display: Check stream before comparing them
+    - drm/amd/display: Fix index out of bounds in DCN30 degamma hardware format
+      translation
+    - drm/amd/display: Fix index out of bounds in degamma hardware format
+      translation
+    - drm/amd/display: Fix index out of bounds in DCN30 color transformation
+    - drm/amd/display: Initialize get_bytes_per_element's default to 1
+    - drm/printer: Allow NULL data in devcoredump printer
+    - scsi: aacraid: Rearrange order of struct aac_srb_unit
+    - drm/radeon/r100: Handle unknown family in r100_cp_init_microcode()
+    - drm/amd/pm: ensure the fw_info is not null before using it
+    - of/irq: Refer to actual buffer size in of_irq_parse_one()
+    - ext4: ext4_search_dir should return a proper error
+    - ext4: avoid use-after-free in ext4_ext_show_leaf()
+    - ext4: fix i_data_sem unlock order in ext4_ind_migrate()
+    - blk-integrity: use sysfs_emit
+    - blk-integrity: convert to struct device_attribute
+    - blk-integrity: register sysfs attributes on struct device
+    - usb: typec: tcpm: Check for port partner validity before consuming it
+    - spi: spi-imx: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - spi: s3c64xx: fix timeout counters in flush_fifo
+    - selftests: breakpoints: use remaining time to check if suspend succeed
+    - selftests: vDSO: fix vDSO name for powerpc
+    - selftests: vDSO: fix vdso_config for powerpc
+    - selftests: vDSO: fix vDSO symbols lookup for powerpc64
+    - selftests/mm: fix charge_reserved_hugetlb.sh test
+    - selftests: vDSO: fix ELF hash table entry size for s390x
+    - selftests: vDSO: fix vdso_config for s390
+    - platform/x86: ISST: Fix the KASAN report slab-out-of-bounds bug
+    - i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume
+    - i2c: qcom-geni: Use IRQF_NO_AUTOEN flag in request_irq()
+    - i2c: xiic: Wait for TX empty to avoid missed TX NAKs
+    - firmware: tegra: bpmp: Drop unused mbox_client_to_bpmp()
+    - spi: bcm63xx: Fix module autoloading
+    - power: supply: hwmon: Fix missing temp1_max_alarm attribute
+    - perf/core: Fix small negative period being ignored
+    - parisc: Fix itlb miss handler for 64-bit programs
+    - drm: Consistently use struct drm_mode_rect for FB_DAMAGE_CLIPS
+    - ALSA: core: add isascii() check to card ID generator
+    - ALSA: usb-audio: Add delay quirk for VIVO USB-C HEADSET
+    - ALSA: usb-audio: Add native DSD support for Luxman D-08u
+    - ALSA: line6: add hw monitor volume control to POD HD500X
+    - ALSA: hda/realtek: Add quirk for Huawei MateBook 13 KLV-WX9
+    - ext4: no need to continue when the number of entries is 1
+    - ext4: correct encrypted dentry name hash when not casefolded
+    - ext4: fix slab-use-after-free in ext4_split_extent_at()
+    - ext4: propagate errors from ext4_find_extent() in ext4_insert_range()
+    - ext4: fix incorrect tid assumption in __jbd2_log_wait_for_space()
+    - ext4: drop ppath from ext4_ext_replay_update_ex() to avoid double-free
+    - ext4: aovid use-after-free in ext4_ext_insert_extent()
+    - ext4: fix double brelse() the buffer of the extents path
+    - ext4: update orig_path in ext4_find_extent()
+    - ext4: fix incorrect tid assumption in ext4_wait_for_tail_page_commit()
+    - ext4: fix incorrect tid assumption in jbd2_journal_shrink_checkpoint_list()
+    - ext4: fix fast commit inode enqueueing during a full journal commit
+    - ext4: use handle to mark fc as ineligible in __track_dentry_update()
+    - ext4: mark fc as ineligible using an handle in ext4_xattr_set()
+    - riscv: define ILLEGAL_POINTER_VALUE for 64bit
+    - exfat: fix memory leak in exfat_load_bitmap()
+    - perf hist: Update hist symbol when updating maps
+    - nfsd: fix delegation_blocked() to block correctly for at least 30 seconds
+    - nfsd: map the EBADMSG to nfserr_io to avoid warning
+    - NFSD: Fix NFSv4's PUTPUBFH operation
+    - aoe: fix the potential use-after-free problem in more places
+    - clk: rockchip: fix error for unknown clocks
+    - clk: qcom: dispcc-sm8250: use CLK_SET_RATE_PARENT for branch clocks
+    - media: sun4i_csi: Implement link validate for sun4i_csi subdev
+    - media: uapi/linux/cec.h: cec_msg_set_reply_to: zero flags
+    - clk: qcom: clk-rpmh: Fix overflow in BCM vote
+    - clk: qcom: gcc-sm8150: De-register gcc_cpuss_ahb_clk_src
+    - media: venus: fix use after free bug in venus_remove due to race condition
+    - clk: qcom: gcc-sm8250: Do not turn off PCIe GDSCs during gdsc_disable()
+    - clk: qcom: gcc-sc8180x: Fix the sdcc2 and sdcc4 clocks freq table
+    - iio: magnetometer: ak8975: Fix reading for ak099xx sensors
+    - tomoyo: fallback to realpath if symlink's pathname does not exist
+    - net: stmmac: Fix zero-division error when disabling tc cbs
+    - rtc: at91sam9: fix OF node leak in probe() error path
+    - Input: adp5589-keys - fix NULL pointer dereference
+    - Input: adp5589-keys - fix adp5589_gpio_get_value()
+    - ACPI: resource: Add Asus Vivobook X1704VAP to irq1_level_low_skip_override[]
+    - ACPI: resource: Add Asus ExpertBook B2502CVA to
+      irq1_level_low_skip_override[]
+    - btrfs: fix a NULL pointer dereference when failed to start a new trasacntion
+    - btrfs: wait for fixup workers before stopping cleaner kthread during umount
+    - gpio: davinci: fix lazy disable
+    - tracing/hwlat: Fix a race during cpuhp processing
+    - tracing/timerlat: Fix a race during cpuhp processing
+    - close_range(): fix the logics in descriptor table trimming
+    - drm/sched: Add locking to drm_sched_entity_modify_sched
+    - drm/amd/display: Fix system hang while resume with TBT monitor
+    - kconfig: qconf: fix buffer overflow in debug links
+    - device property: Add fwnode_iomap()
+    - device property: Add fwnode_irq_get_byname
+    - i2c: smbus: Use device_*() functions instead of of_*()
+    - i2c: create debugfs entry per adapter
+    - i2c: core: Lock address during client device instantiation
+    - i2c: xiic: Use devm_clk_get_enabled()
+    - i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled
+    - spi: bcm63xx: Fix missing pm_runtime_disable()
+    - ext4: properly sync file size update after O_SYNC direct IO
+    - ext4: dax: fix overflowing extents beyond inode size when partially writing
+    - arm64: Add Cortex-715 CPU part definition
+    - arm64: cputype: Add Neoverse-N3 definitions
+    - arm64: errata: Expand speculative SSBS workaround once more
+    - uprobes: fix kernel info leak via "[uprobes]" vma
+    - drm/amd/display: Allow backlight to go below
+      `AMDGPU_DM_DEFAULT_MIN_BACKLIGHT`
+    - build-id: require program headers to be right after ELF header
+    - lib/buildid: harden build ID parsing logic
+    - drm/rockchip: define gamma registers for RK3399
+    - drm/rockchip: support gamma control on RK3399
+    - drm/rockchip: vop: clear DMA stop bit on RK3066
+    - media: i2c: imx335: Enable regulator supplies
+    - media: imx335: Fix reset-gpio handling
+    - dt-bindings: clock: qcom: Add missing UFS QREF clocks
+    - dt-bindings: clock: qcom: Add GPLL9 support on gcc-sc8180x
+    - r8169: Fix spelling mistake: "tx_underun" -> "tx_underrun"
+    - r8169: add tally counter fields added with RTL8125
+    - clk: qcom: gcc-sc8180x: Add GPLL9 support
+    - ACPI: battery: Simplify battery hook locking
+    - ACPI: battery: Fix possible crash when unregistering a battery hook
+    - Revert "arm64: dts: qcom: sm8250: switch UFS QMP PHY to new style of
+      bindings"
+    - ext4: fix inode tree inconsistency caused by ENOMEM
+    - 9p: add missing locking around taking dentry fid list
+    - vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
+    - perf report: Fix segfault when 'sym' sort key is not used
+    - ALSA: usb-audio: Fix possible NULL pointer dereference in
+      snd_usb_pcm_has_fixed_rate()
+    - unicode: Don't special case ignorable code points
+    - net: ethernet: cortina: Drop TSO support
+    - tracing: Remove precision vsnprintf() check from print event
+    - drm/crtc: fix uninitialized variable use even harder
+    - tracing: Have saved_cmdlines arrays all in one allocation
+    - selftests/net: give more time to udpgro bg processes to complete startup
+    - selftests/net: synchronize udpgro tests' tx and rx connection
+    - selftests: net: Remove executable bits from library scripts
+    - fs/ntfs3: Refactor enum_rstbl to suppress static checker
+    - virtio_console: fix misc probe bugs
+    - Input: synaptics-rmi4 - fix UAF of IRQ domain on driver removal
+    - bpf: Check percpu map value size first
+    - s390/facility: Disable compile time optimization for decompressor code
+    - s390/mm: Add cond_resched() to cmm_alloc/free_pages()
+    - bpf, x64: Fix a jit convergence issue
+    - ext4: don't set SB_RDONLY after filesystem errors
+    - ext4: nested locking for xattr inode
+    - s390/cpum_sf: Remove WARN_ON_ONCE statements
+    - ktest.pl: Avoid false positives with grub2 skip regex
+    - RDMA/mad: Improve handling of timed out WRs of mad agent
+    - PCI: Add function 0 DMA alias quirk for Glenfly Arise chip
+    - RDMA/rtrs-srv: Avoid null pointer deref during path establishment
+    - clk: bcm: bcm53573: fix OF node leak in init
+    - PCI: Add ACS quirk for Qualcomm SA8775P
+    - i2c: i801: Use a different adapter-name for IDF adapters
+    - PCI: Mark Creative Labs EMU20k2 INTx masking as broken
+    - ntb: ntb_hw_switchtec: Fix use after free vulnerability in
+      switchtec_ntb_remove due to race condition
+    - media: videobuf2-core: clear memory related fields in
+      __vb2_plane_dmabuf_put()
+    - remoteproc: imx_rproc: Use imx specific hook for find_loaded_rsc_table
+    - clk: imx: Remove CLK_SET_PARENT_GATE for DRAM mux for i.MX7D
+    - usb: chipidea: udc: enable suspend interrupt after usb reset
+    - usb: dwc2: Adjust the timing of USB Driver Interrupt Registration in the
+      Crashkernel Scenario
+    - comedi: ni_routing: tools: Check when the file could not be opened
+    - virtio_pmem: Check device status before requesting flush
+    - tools/iio: Add memory allocation failure check for trigger_name
+    - driver core: bus: Return -EIO instead of 0 when show/store invalid bus
+      attribute
+    - drm/amd/display: Check null pointer before dereferencing se
+    - fbdev: sisfb: Fix strbuf array overflow
+    - RDMA/rxe: Fix seg fault in rxe_comp_queue_pkt
+    - NFSD: Mark filecache "down" if init fails
+    - ice: fix VLAN replay after reset
+    - SUNRPC: Fix integer overflow in decode_rc_list()
+    - NFSv4: Prevent NULL-pointer dereference in nfs42_complete_copies()
+    - net: phy: dp83869: fix memory corruption when enabling fiber
+    - tcp: fix to allow timestamp undo if no retransmits were sent
+    - tcp: fix tcp_enter_recovery() to zero retrans_stamp when it's safe
+    - netfilter: br_netfilter: fix panic with metadata_dst skb
+    - Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
+    - net: phy: bcm84881: Fix some error handling paths
+    - thermal: int340x: processor_thermal: Set feature mask before
+      proc_thermal_add
+    - thermal: intel: int340x: processor: Fix warning during module unload
+    - net: dsa: b53: fix jumbo frame mtu check
+    - net: dsa: b53: fix max MTU for 1g switches
+    - net: dsa: b53: fix max MTU for BCM5325/BCM5365
+    - net: dsa: b53: allow lower MTUs on BCM5325/5365
+    - net: dsa: b53: fix jumbo frames on 10/100 ports
+    - gpio: aspeed: Add the flush write to ensure the write complete.
+    - gpio: aspeed: Use devm_clk api to manage clock source
+    - ice: Fix netif_is_ice() in Safe Mode
+    - i40e: Fix macvlan leak by synchronizing access to mac_filter_hash
+    - igb: Do not bring the device up after non-fatal error
+    - net/sched: accept TCA_STAB only for root qdisc
+    - net: ibm: emac: mal: fix wrong goto
+    - sctp: ensure sk_state is set to CLOSED if hashing fails in sctp_listen_start
+    - netfilter: xtables: avoid NFPROTO_UNSPEC where needed
+    - net: Add l3mdev index to flow struct and avoid oif reset for port devices
+    - netfilter: rpfilter/fib: Populate flowic_l3mdev field
+    - netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
+    - netfilter: fib: check correct rtable in vrf setups
+    - net: rtnetlink: add msg kind names
+    - rtnetlink: Add bulk registration helpers for rtnetlink message handlers.
+    - mctp: Handle error of rtnl_register_module().
+    - ppp: fix ppp_async_encode() illegal access
+    - slip: make slhc_remember() more robust against malicious packets
+    - RDMA/hns: Fix UAF for cq async event
+    - x86/fpu: Avoid writing LBR bit to IA32_XSS unless supported
+    - hwmon: (tmp513) Add missing dependency on REGMAP_I2C
+    - hwmon: (adm9240) Add missing dependency on REGMAP_I2C
+    - hwmon: (adt7470) Add missing dependency on REGMAP_I2C
+    - HID: amd_sfh: Switch to device-managed dmam_alloc_coherent()
+    - resource: fix region_intersects() vs add_memory_driver_managed()
+    - HID: plantronics: Workaround for an unexcepted opposite volume key
+    - Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
+    - usb: dwc3: core: Stop processing of pending events if controller is halted
+    - usb: xhci: Fix problem with xhci resume from suspend
+    - usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
+    - hid: intel-ish-hid: Fix uninitialized variable 'rv' in
+      ish_fw_xfer_direct_dma
+    - drm/v3d: Stop the active perfmon before being destroyed
+    - net: explicitly clear the sk pointer, when pf->create fails
+    - net: Fix an unsafe loop on the list
+    - net: dsa: lan9303: ensure chip reset and wait for READY status
+    - mptcp: pm: do not remove closing subflows
+    - nouveau/dmem: Fix vulnerability in migrate_to_ram upon copy error
+    - kthread: unpark only parked kthread
+    - block, bfq: fix uaf for accessing waker_bfqq after splitting
+    - i2c: smbus: Check for parent device before dereference
+    - net: geneve: add missing netlink policy and size for
+      IFLA_GENEVE_INNER_PROTO_INHERIT
+    - xfrm: Pass flowi_oif or l3mdev as oif to xfrm_dst_lookup
+    - net: Handle l3mdev in ip_tunnel_init_flow
+    - net: seg6: fix seg6_lookup_any_nexthop() to handle VRFs using flowi_l3mdev
+    - net: vrf: determine the dst using the original ifindex for multicast
+    - netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
+    - ext4: fix warning in ext4_dio_write_end_io()
+    - net: axienet: start napi before enabling Rx/Tx
+    - selftests: net: more strict check in net_helper
+    - net: xilinx: axienet: Schedule NAPI in two steps
+    - Linux 5.15.168
+  * CVE-2024-36968
+    - Bluetooth: L2CAP: Fix div-by-zero in l2cap_le_flowctl_init()
+  * CVE-2024-35904
+    - selinux: avoid dereference of garbage after mount failure
+  * IOMMU warnings on AMD systems after booting into kdump kernel
+    (LP: #2080378)
+    - iommu/amd: Simplify and Consolidate Virtual APIC (AVIC) Enablement
+    - iommu/amd: Fix compile warning in init code
+  * CVE-2024-42156
+    - s390/pkey: Wipe copies of clear-key structures on failure
+  * CVE-2024-44942
+    - f2fs: fix to do sanity check on F2FS_INLINE_DATA flag in inode during GC
+  * CVE-2024-38538
+    - net: bridge: xmit: make sure we have at least eth header len bytes
+  * CVE-2024-42158
+    - s390/pkey: Use kfree_sensitive() to fix Coccinelle warnings
+  * CVE-2024-38667
+    - riscv: prevent pt_regs corruption for secondary idle threads
+  * CVE-2024-44940
+    - fou: remove warn in gue_gro_receive on unsupported protocol
+  * CVE-2024-42079
+    - gfs2: Fix NULL pointer dereference in gfs2_log_flush
+  * CVE-2024-35951
+    - drm/panfrost: Fix the error path in panfrost_mmu_map_fault_addr()
+  * LXD fan bridge causes blocked tasks (LP: #2064176)
+    - SAUCE: fan: release rcu_read_lock on skb discard path
+  * CVE-2023-52532
+    - net: mana: Fix TX CQE error handling
+  * CVE-2023-52621
+    - bpf: Check rcu_read_lock_trace_held() before calling bpf map helpers
+  * CVE-2024-26947
+    - ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses
+  * CVE-2023-52639
+    - KVM: s390: vsie: fix race during shadow creation
+
+  [ Ubuntu: 5.15.0-126.136 ]
+
+  * jammy/linux: 5.15.0-126.136 -proposed tracker (LP: #2086027)
+    - [Packaging] resync git-ubuntu-log
+  * Cannot detect audio sinks and sources in proposed kernel (LP: #2085082)
+    - soundwire: stream: Revert "soundwire: stream: fix programming slave ports
+      for non-continous port maps"
+
+ -- Ubuntu Kernel Preparation Bot <ubuntu-kernel-bot@canonical.com>  Thu, 21 Nov 2024 23:54:48 +0000
+
+linux-xilinx-zynqmp (5.15.0-1038.42) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1038.42 -proposed tracker (LP: #2082998)
+
+  [ Ubuntu: 5.15.0-125.135 ]
+
+  * jammy/linux: 5.15.0-125.135 -proposed tracker (LP: #2083001)
+  * CVE-2024-26800
+    - tls: rx: coalesce exit paths in tls_decrypt_sg()
+    - tls: separate no-async decryption request handling from async
+    - tls: fix use-after-free on failed backlog decryption
+  * Please backport the more restrictive XSAVES deactivation for  Zen1/2 arch
+    (LP: #2077321)
+    - x86/CPU/AMD: Improve the erratum 1386 workaround
+  * Jammy update: v5.15.167 upstream stable release (LP: #2081279)
+    - drm: panel-orientation-quirks: Add quirk for OrangePi Neo
+    - ALSA: hda/generic: Add a helper to mute speakers at suspend/shutdown
+    - ALSA: hda/conexant: Mute speakers at suspend / shutdown
+    - i2c: Fix conditional for substituting empty ACPI functions
+    - dma-debug: avoid deadlock between dma debug vs printk and netconsole
+    - net: usb: qmi_wwan: add MeiG Smart SRM825L
+    - drm/amdgpu: Fix uninitialized variable warning in amdgpu_afmt_acr
+    - drm/amd/display: Assign linear_pitch_alignment even for VM
+    - drm/amdgpu: fix overflowed array index read warning
+    - drm/amdgpu/pm: Check the return value of smum_send_msg_to_smc
+    - drm/amd/pm: fix uninitialized variable warning for smu8_hwmgr
+    - drm/amd/pm: fix warning using uninitialized value of max_vid_step
+    - drm/amd/pm: fix the Out-of-bounds read warning
+    - drm/amdgpu: fix uninitialized scalar variable warning
+    - drm/amd/pm: fix uninitialized variable warnings for vega10_hwmgr
+    - drm/amdgpu: avoid reading vf2pf info size from FB
+    - drm/amd/display: Check gpio_id before used as array index
+    - drm/amd/display: Stop amdgpu_dm initialize when stream nums greater than 6
+    - drm/amd/display: Add array index check for hdcp ddc access
+    - drm/amd/display: Check num_valid_sets before accessing reader_wm_sets[]
+    - drm/amd/display: Check msg_id before processing transcation
+    - drm/amd/display: Fix Coverity INTEGER_OVERFLOW within
+      dal_gpio_service_create
+    - drm/amd/amdgpu: Check tbo resource pointer
+    - drm/amdgpu/pm: Fix uninitialized variable warning for smu10
+    - drm/amdgpu/pm: Fix uninitialized variable agc_btc_response
+    - drm/amdgpu: Fix out-of-bounds write warning
+    - drm/amdgpu: Fix out-of-bounds read of df_v1_7_channel_number
+    - drm/amdgpu: fix ucode out-of-bounds read warning
+    - drm/amdgpu: fix mc_data out-of-bounds read warning
+    - drm/amdkfd: Reconcile the definition and use of oem_id in struct
+      kfd_topology_device
+    - apparmor: fix possible NULL pointer dereference
+    - drm/amdgpu/pm: Check input value for CUSTOM profile mode setting on legacy
+      SOCs
+    - drm/amdgpu: fix the waring dereferencing hive
+    - drm/amd/pm: check specific index for aldebaran
+    - drm/amdgpu: the warning dereferencing obj for nbio_v7_4
+    - drm/amd/pm: check negtive return for table entries
+    - drm/amdgpu: update type of buf size to u32 for eeprom functions
+    - wifi: iwlwifi: remove fw_running op
+    - cpufreq: scmi: Avoid overflow of target_freq in fast switch
+    - PCI: al: Check IORESOURCE_BUS existence during probe
+    - hwspinlock: Introduce hwspin_lock_bust()
+    - RDMA/efa: Properly handle unexpected AQ completions
+    - ionic: fix potential irq name truncation
+    - rcu/nocb: Remove buggy bypass lock contention mitigation
+    - usbip: Don't submit special requests twice
+    - usb: typec: ucsi: Fix null pointer dereference in trace
+    - fsnotify: clear PARENT_WATCHED flags lazily
+    - smack: tcp: ipv4, fix incorrect labeling
+    - drm/meson: plane: Add error handling
+    - drm/bridge: tc358767: Check if fully initialized before signalling HPD event
+      via IRQ
+    - wifi: cfg80211: make hash table duplicates more survivable
+    - block: remove the blk_flush_integrity call in blk_integrity_unregister
+    - drm/amd/display: Skip wbscl_set_scaler_filter if filter is null
+    - media: uvcvideo: Enforce alignment of frame and interval
+    - drm/amd/pm: Fix the null pointer dereference for vega10_hwmgr
+    - virtio_net: Fix napi_skb_cache_put warning
+    - rcu-tasks: Fix show_rcu_tasks_trace_gp_kthread buffer overflow
+    - ext4: reject casefold inode flag without casefold feature
+    - udf: Limit file size to 4TB
+    - ext4: handle redirtying in ext4_bio_write_page()
+    - i2c: Use IS_REACHABLE() for substituting empty ACPI functions
+    - sch/netem: fix use after free in netem_dequeue
+    - ASoC: dapm: Fix UAF for snd_soc_pcm_runtime object
+    - KVM: SVM: fix emulation of msr reads/writes of MSR_FS_BASE and MSR_GS_BASE
+    - KVM: SVM: Don't advertise Bus Lock Detect to guest if SVM support is missing
+    - ALSA: hda/conexant: Add pincfg quirk to enable top speakers on Sirius
+      devices
+    - ALSA: hda/realtek: add patch for internal mic in Lenovo V145
+    - ALSA: hda/realtek: Support mute LED on HP Laptop 14-dq2xxx
+    - ata: libata: Fix memory leak for error path in ata_host_alloc()
+    - irqchip/gic-v2m: Fix refcount leak in gicv2m_of_init()
+    - rtmutex: Drop rt_mutex::wait_lock before scheduling
+    - nvme-pci: Add sleep quirk for Samsung 990 Evo
+    - Revert "Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE"
+    - Bluetooth: MGMT: Ignore keys being loaded with invalid type
+    - mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K
+    - mmc: sdhci-of-aspeed: fix module autoloading
+    - mmc: cqhci: Fix checking of CQHCI_HALT state
+    - fuse: update stats for pages in dropped aux writeback list
+    - fuse: use unsigned type for getxattr/listxattr size truncation
+    - clk: qcom: clk-alpha-pll: Fix the pll post div mask
+    - clk: qcom: clk-alpha-pll: Fix the trion pll postdiv set rate API
+    - can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open
+    - tracing: Avoid possible softlockup in tracing_iter_reset()
+    - ila: call nf_unregister_net_hooks() sooner
+    - sched: sch_cake: fix bulk flow accounting logic for host fairness
+    - nilfs2: fix missing cleanup on rollforward recovery error
+    - nilfs2: fix state management in error path of log writing function
+    - mptcp: pm: re-using ID of unused flushed subflows
+    - mptcp: pm: only decrement add_addr_accepted for MPJ req
+    - mptcp: pm: check add_addr_accept_max before accepting new ADD_ADDR
+    - mptcp: pm: fullmesh: select the right ID later
+    - mptcp: constify a bunch of of helpers
+    - mptcp: pm: avoid possible UaF when selecting endp
+    - mptcp: avoid duplicated SUB_CLOSED events
+    - mptcp: close subflow when receiving TCP+FIN
+    - mptcp: pm: ADD_ADDR 0 is not a new address
+    - mptcp: pm: do not remove already closed subflows
+    - mptcp: pm: skip connecting to already established sf
+    - mptcp: pr_debug: add missing \n at the end
+    - mptcp: pm: send ACK on an active subflow
+    - ALSA: hda: Add input value sanity checks to HDMI channel map controls
+    - smack: unix sockets: fix accept()ed socket label
+    - irqchip/armada-370-xp: Do not allow mapping IRQ 0 and 1
+    - af_unix: Remove put_pid()/put_cred() in copy_peercred().
+    - iommu: sun50i: clear bypass register
+    - netfilter: nf_conncount: fix wrong variable type
+    - udf: Avoid excessive partition lengths
+    - media: vivid: fix wrong sizeimage value for mplane
+    - leds: spi-byte: Call of_node_put() on error path
+    - wifi: brcmsmac: advertise MFP_CAPABLE to enable WPA3
+    - usb: uas: set host status byte on data completion error
+    - drm/amd/display: Check HDCP returned status
+    - media: vivid: don't set HDMI TX controls if there are no HDMI outputs
+    - PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
+    - media: qcom: camss: Add check for v4l2_fwnode_endpoint_parse
+    - pcmcia: Use resource_size function on resource object
+    - drm/amdgpu: check for LINEAR_ALIGNED correctly in check_tiling_flags_gfx6
+    - can: bcm: Remove proc entry when dev is unregistered.
+    - can: m_can: Release irq on error in m_can_open
+    - igb: Fix not clearing TimeSync interrupts for 82580
+    - platform/x86: dell-smbios: Fix error path in dell_smbios_init()
+    - tcp_bpf: fix return value of tcp_bpf_sendmsg()
+    - igc: Unlock on error in igc_io_resume()
+    - ice: check ICE_VSI_DOWN under rtnl_lock when preparing for reset
+    - net: usb: don't write directly to netdev->dev_addr
+    - usbnet: modern method to get random MAC
+    - bareudp: Fix device stats updates.
+    - gro: remove rcu_read_lock/rcu_read_unlock from gro_receive handlers
+    - gro: remove rcu_read_lock/rcu_read_unlock from gro_complete handlers
+    - fou: Fix null-ptr-deref in GRO.
+    - net: bridge: br_fdb_external_learn_add(): always set EXT_LEARN
+    - net: dsa: vsc73xx: fix possible subblocks range of CAPT block
+    - ASoC: topology: Properly initialize soc_enum values
+    - dm init: Handle minors larger than 255
+    - iommu/vt-d: Handle volatile descriptor status read
+    - cgroup: Protect css->cgroup write under css_set_lock
+    - um: line: always fill *error_out in setup_one_line()
+    - devres: Initialize an uninitialized struct member
+    - pci/hotplug/pnv_php: Fix hotplug driver crash on Powernv
+    - hwmon: (adc128d818) Fix underflows seen when writing limit attributes
+    - hwmon: (lm95234) Fix underflows seen when writing limit attributes
+    - hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
+    - hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
+    - libbpf: Add NULL checks to bpf_object__{prev_map,next_map}
+    - drm/amdgpu: Set no_hw_access when VF request full GPU fails
+    - ext4: fix possible tid_t sequence overflows
+    - dma-mapping: benchmark: Don't starve others when doing the test
+    - wifi: mwifiex: Do not return unused priv in mwifiex_get_priv_by_id()
+    - smp: Add missing destroy_work_on_stack() call in smp_call_on_cpu()
+    - fs/ntfs3: Check more cases when directory is corrupted
+    - btrfs: replace BUG_ON with ASSERT in walk_down_proc()
+    - btrfs: clean up our handling of refs == 0 in snapshot delete
+    - btrfs: replace BUG_ON() with error handling at update_ref_for_cow()
+    - riscv: set trap vector earlier
+    - PCI: Add missing bridge lock to pci_bus_lock()
+    - net: dpaa: avoid on-stack arrays of NR_CPUS elements
+    - i3c: mipi-i3c-hci: Error out instead on BUG_ON() in IBI DMA setup
+    - kselftests: dmabuf-heaps: Ensure the driver name is null-terminated
+    - btrfs: initialize location to fix -Wmaybe-uninitialized in
+      btrfs_lookup_dentry()
+    - s390/vmlinux.lds.S: Move ro_after_init section behind rodata section
+    - HID: cougar: fix slab-out-of-bounds Read in cougar_report_fixup
+    - HID: amd_sfh: free driver_data after destroying hid device
+    - Input: uinput - reject requests with unreasonable number of slots
+    - usbnet: ipheth: race between ipheth_close and error handling
+    - Squashfs: sanity check symbolic link size
+    - of/irq: Prevent device address out-of-bounds read in interrupt map walk
+    - lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc()
+    - MIPS: cevt-r4k: Don't call get_c0_compare_int if timer irq is installed
+    - ata: pata_macio: Use WARN instead of BUG
+    - NFSv4: Add missing rescheduling points in
+      nfs_client_return_marked_delegations
+    - cifs: Check the lease context if we actually got a lease
+    - staging: iio: frequency: ad9834: Validate frequency parameter value
+    - iio: buffer-dmaengine: fix releasing dma channel on error
+    - iio: fix scale application in iio_convert_raw_to_processed_unlocked
+    - iio: adc: ad7124: fix config comparison
+    - iio: adc: ad7124: fix chip ID mismatch
+    - usb: dwc3: core: update LC timer as per USB Spec V3.2
+    - binder: fix UAF caused by offsets overwrite
+    - nvmem: Fix return type of devm_nvmem_device_get() in kerneldoc
+    - uio_hv_generic: Fix kernel NULL pointer dereference in hv_uio_rescind
+    - Drivers: hv: vmbus: Fix rescind handling in uio_hv_generic
+    - VMCI: Fix use-after-free when removing resource in vmci_resource_remove()
+    - clocksource/drivers/imx-tpm: Fix return -ETIME when delta exceeds INT_MAX
+    - clocksource/drivers/imx-tpm: Fix next event not taking effect sometime
+    - clocksource/drivers/timer-of: Remove percpu irq related code
+    - uprobes: Use kzalloc to allocate xol area
+    - perf/aux: Fix AUX buffer serialization
+    - ksmbd: unset the binding mark of a reused connection
+    - ksmbd: Unlock on in ksmbd_tcp_set_interfaces()
+    - nilfs2: replace snprintf in show functions with sysfs_emit
+    - nilfs2: protect references to superblock parameters exposed in sysfs
+    - workqueue: wq_watchdog_touch is always called with valid CPU
+    - workqueue: Improve scalability of workqueue watchdog touch
+    - ACPI: processor: Return an error if acpi_processor_get_info() fails in
+      processor_add()
+    - ACPI: processor: Fix memory leaks in error paths of processor_add()
+    - arm64: acpi: Move get_cpu_for_acpi_id() to a header
+    - arm64: acpi: Harden get_cpu_for_acpi_id() against missing CPU entry
+    - nvmet-tcp: fix kernel crash if commands allocation fails
+    - ASoC: sunxi: sun4i-i2s: fix LRCLK polarity in i2s mode
+    - drm/i915/fence: Mark debug_fence_init_onstack() with __maybe_unused
+    - drm/i915/fence: Mark debug_fence_free() with __maybe_unused
+    - gpio: rockchip: fix OF node leak in probe()
+    - net: more strict VIRTIO_NET_HDR_GSO_UDP_L4 validation
+    - net: change maximum number of UDP segments to 128
+    - gso: fix dodgy bit handling for GSO_UDP_L4
+    - net: drop bad gso csum_start and offset in virtio_net_hdr
+    - x86/mm: Fix PTI for i386 some more
+    - net, sunrpc: Remap EPERM in case of connection failure in
+      xs_tcp_setup_socket
+    - btrfs: fix race between direct IO write and fsync when using same fd
+    - memcg: protect concurrent access to mem_cgroup_idr
+    - udp: fix receiving fraglist GSO packets
+    - Linux 5.15.167
+  * CVE-2024-41071
+    - wifi: mac80211: Avoid address calculations via out of bounds array indexing
+  * CVE-2024-40915
+    - riscv: rewrite __kernel_map_pages() to fix sleeping in invalid context
+  * CVE-2024-38611
+    - media: i2c: et8ek8: Don't strip remove function when driver is builtin
+  * CVE-2024-38602
+    - ax25: Fix reference count leak issues of ax25_dev
+  * CVE-2024-26669
+    - net/sched: flower: Fix chain template offload
+  * CVE-2024-26607
+    - drm/bridge: sii902x: Fix probing race issue
+  * Jammy update: v5.15.166 upstream stable release (LP: #2080594)
+    - fuse: Initialize beyond-EOF page contents before setting uptodate
+    - char: xillybus: Don't destroy workqueue from work item running on it
+    - char: xillybus: Refine workqueue handling
+    - char: xillybus: Check USB endpoints when probing device
+    - ALSA: usb-audio: Add delay quirk for VIVO USB-C-XE710 HEADSET
+    - ALSA: usb-audio: Support Yamaha P-125 quirk entry
+    - xhci: Fix Panther point NULL pointer deref at full-speed re-enumeration
+    - thunderbolt: Mark XDomain as unplugged when router is removed
+    - s390/dasd: fix error recovery leading to data corruption on ESE devices
+    - arm64: ACPI: NUMA: initialize all values of acpi_early_node_map to
+      NUMA_NO_NODE
+    - dm resume: don't return EINVAL when signalled
+    - dm persistent data: fix memory allocation failure
+    - vfs: Don't evict inode under the inode lru traversing context
+    - fs/ntfs3: add prefix to bitmap_size() and use BITS_TO_U64()
+    - s390/cio: rename bitmap_size() -> idset_bitmap_size()
+    - btrfs: rename bitmap_set_bits() -> btrfs_bitmap_set_bits()
+    - bitmap: introduce generic optimized bitmap_size()
+    - fix bitmap corruption on close_range() with CLOSE_RANGE_UNSHARE
+    - selinux: fix potential counting error in avc_add_xperms_decision()
+    - btrfs: tree-checker: add dev extent item checks
+    - drm/amdgpu: Actually check flags for all context ops.
+    - memcg_write_event_control(): fix a user-triggerable oops
+    - drm/amdgpu/jpeg2: properly set atomics vmid field
+    - s390/uv: Panic for set and remove shared access UVC errors
+    - igc: Correct the launchtime offset
+    - igc: remove I226 Qbv BaseTime restriction
+    - igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer
+    - net/mlx5e: Correctly report errors for ethtool rx flows
+    - atm: idt77252: prevent use after free in dequeue_rx()
+    - net: axienet: Fix register defines comment description
+    - net: dsa: vsc73xx: pass value in phy_write operation
+    - net: dsa: vsc73xx: use read_poll_timeout instead delay loop
+    - net: dsa: vsc73xx: check busy flag in MDIO operations
+    - mlxbf_gige: Remove two unused function declarations
+    - mlxbf_gige: disable RX filters until RX path initialized
+    - mptcp: correct MPTCP_SUBFLOW_ATTR_SSN_OFFSET reserved size
+    - netfilter: allow ipv6 fragments to arrive on different devices
+    - netfilter: flowtable: initialise extack before use
+    - netfilter: nf_queue: drop packets with cloned unconfirmed conntracks
+    - net: hns3: fix wrong use of semaphore up
+    - net: hns3: fix a deadlock problem when config TC during resetting
+    - ALSA: hda/realtek: Fix noise from speakers on Lenovo IdeaPad 3 15IAU7
+    - ssb: Fix division by zero issue in ssb_calc_clock_rate
+    - wifi: cfg80211: check wiphy mutex is held for wdev mutex
+    - wifi: mac80211: fix BA session teardown race
+    - wifi: cw1200: Avoid processing an invalid TIM IE
+    - i2c: riic: avoid potential division by zero
+    - RDMA/rtrs: Fix the problem of variable not initialized fully
+    - s390/smp,mcck: fix early IPI handling
+    - i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
+    - i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
+    - media: radio-isa: use dev_name to fill in bus_info
+    - staging: iio: resolver: ad2s1210: fix use before initialization
+    - drm/amd/display: Validate hw_points_num before using it
+    - staging: ks7010: disable bh on tx_dev_lock
+    - binfmt_misc: cleanup on filesystem umount
+    - media: qcom: venus: fix incorrect return value
+    - scsi: spi: Fix sshdr use
+    - gfs2: setattr_chown: Add missing initialization
+    - wifi: iwlwifi: abort scan when rfkill on but device enabled
+    - wifi: iwlwifi: fw: Fix debugfs command sending
+    - IB/hfi1: Fix potential deadlock on &irq_src_lock and &dd->uctxt_lock
+    - hwmon: (ltc2992) Avoid division by zero
+    - arm64: Fix KASAN random tag seed initialization
+    - memory: tegra: Skip SID programming if SID registers aren't set
+    - powerpc/xics: Check return value of kasprintf in icp_native_map_one_cpu
+    - nvmet-trace: avoid dereferencing pointer too early
+    - ext4: do not trim the group with corrupted block bitmap
+    - afs: fix __afs_break_callback() / afs_drop_open_mmap() race
+    - fuse: fix UAF in rcu pathwalks
+    - quota: Remove BUG_ON from dqget()
+    - media: pci: cx23885: check cx23885_vdev_init() return
+    - fs: binfmt_elf_efpic: don't use missing interpreter's properties
+    - scsi: lpfc: Initialize status local variable in lpfc_sli4_repost_sgl_list()
+    - media: drivers/media/dvb-core: copy user arrays safely
+    - net/sun3_82586: Avoid reading past buffer in debug output
+    - drm/lima: set gp bus_stop bit before hard reset
+    - virtiofs: forbid newlines in tags
+    - clocksource/drivers/arm_global_timer: Guard against division by zero
+    - netlink: hold nlk->cb_mutex longer in __netlink_dump_start()
+    - md: clean up invalid BUG_ON in md_ioctl
+    - x86: Increase brk randomness entropy for 64-bit systems
+    - memory: stm32-fmc2-ebi: check regmap_read return value
+    - parisc: Use irq_enter_rcu() to fix warning at kernel/context_tracking.c:367
+    - powerpc/boot: Handle allocation failure in simple_realloc()
+    - powerpc/boot: Only free if realloc() succeeds
+    - btrfs: change BUG_ON to assertion when checking for delayed_node root
+    - btrfs: handle invalid root reference found in may_destroy_subvol()
+    - btrfs: send: handle unexpected data in header buffer in begin_cmd()
+    - btrfs: change BUG_ON to assertion in tree_move_down()
+    - btrfs: delete pointless BUG_ON check on quota root in
+      btrfs_qgroup_account_extent()
+    - f2fs: fix to do sanity check in update_sit_entry
+    - usb: gadget: fsl: Increase size of name buffer for endpoints
+    - Bluetooth: bnep: Fix out-of-bound access
+    - net: hns3: add checking for vf id of mailbox
+    - nvmet-tcp: do not continue for invalid icreq
+    - NFS: avoid infinite loop in pnfs_update_layout.
+    - openrisc: Call setup_memory() earlier in the init sequence
+    - s390/iucv: fix receive buffer virtual vs physical address confusion
+    - clocksource: Make watchdog and suspend-timing multiplication overflow safe
+    - platform/x86: lg-laptop: fix %s null argument warning
+    - usb: dwc3: core: Skip setting event buffers for host only controllers
+    - irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
+    - ext4: set the type of max_zeroout to unsigned int to avoid overflow
+    - nvmet-rdma: fix possible bad dereference when freeing rsps
+    - hrtimer: Prevent queuing of hrtimer without a function callback
+    - gtp: pull network headers in gtp_dev_xmit()
+    - block: use "unsigned long" for blk_validate_block_size().
+    - nfsd: move reply cache initialization into nfsd startup
+    - nfsd: move init of percpu reply_cache_stats counters back to nfsd_init_net
+    - NFSD: Refactor nfsd_reply_cache_free_locked()
+    - NFSD: Rename nfsd_reply_cache_alloc()
+    - NFSD: Replace nfsd_prune_bucket()
+    - NFSD: Refactor the duplicate reply cache shrinker
+    - NFSD: Rewrite synopsis of nfsd_percpu_counters_init()
+    - NFSD: Fix frame size warning in svc_export_parse()
+    - sunrpc: don't change ->sv_stats if it doesn't exist
+    - nfsd: stop setting ->pg_stats for unused stats
+    - sunrpc: pass in the sv_stats struct through svc_create_pooled
+    - sunrpc: remove ->pg_stats from svc_program
+    - sunrpc: use the struct net as the svc proc private
+    - nfsd: rename NFSD_NET_* to NFSD_STATS_*
+    - nfsd: expose /proc/net/sunrpc/nfsd in net namespaces
+    - nfsd: make all of the nfsd stats per-network namespace
+    - nfsd: remove nfsd_stats, make th_cnt a global counter
+    - nfsd: make svc_stat per-network namespace instead of global
+    - media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)
+    - dm suspend: return -ERESTARTSYS instead of -EINTR
+    - net: mana: Fix doorbell out of order violation and avoid unnecessary
+      doorbell rings
+    - platform/surface: aggregator: Fix warning when controller is destroyed in
+      probe
+    - Bluetooth: hci_core: Fix LE quote calculation
+    - Bluetooth: SMP: Fix assumption of Central always being Initiator
+    - tc-testing: don't access non-existent variable on exception
+    - kcm: Serialise kcm_sendmsg() for the same socket.
+    - netfilter: nft_counter: Disable BH in nft_counter_offload_stats().
+    - netfilter: nft_counter: Synchronize nft_counter_reset() against reader.
+    - ip6_tunnel: Fix broken GRO
+    - bonding: fix bond_ipsec_offload_ok return type
+    - bonding: fix null pointer deref in bond_ipsec_offload_ok
+    - bonding: fix xfrm real_dev null pointer dereference
+    - bonding: fix xfrm state handling when clearing active slave
+    - ice: fix ICE_LAST_OFFSET formula
+    - dpaa2-switch: Fix error checking in dpaa2_switch_seed_bp()
+    - net: dsa: mv88e6xxx: read FID when handling ATU violations
+    - net: dsa: mv88e6xxx: replace ATU violation prints with trace points
+    - net: dsa: mv88e6xxx: Fix out-of-bound access
+    - ipv6: prevent UAF in ip6_send_skb()
+    - ipv6: fix possible UAF in ip6_finish_output2()
+    - ipv6: prevent possible UAF in ip6_xmit()
+    - netfilter: flowtable: validate vlan header
+    - net: xilinx: axienet: Always disable promiscuous mode
+    - net: xilinx: axienet: Fix dangling multicast addresses
+    - drm/msm/dpu: don't play tricks with debug macros
+    - drm/msm/dp: reset the link phy params before link training
+    - drm/msm/dpu: cleanup FB if dpu_format_populate_layout fails
+    - mmc: mmc_test: Fix NULL dereference on allocation failure
+    - Bluetooth: MGMT: Add error handling to pair_device()
+    - scsi: core: Fix the return value of scsi_logical_block_count()
+    - MIPS: Loongson64: Set timer mode in cpu-probe
+    - HID: wacom: Defer calculation of resolution until resolution_code is known
+    - HID: microsoft: Add rumble support to latest xbox controllers
+    - cxgb4: add forgotten u64 ivlan cast before shift
+    - KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3
+    - mmc: dw_mmc: allow biu and ciu clocks to defer
+    - Revert "drm/amd/display: Validate hw_points_num before using it"
+    - hwmon: (ltc2992) Fix memory leak in ltc2992_parse_dt()
+    - ALSA: timer: Relax start tick time check for slave timer elements
+    - mm/numa: no task_numa_fault() call if PMD is changed
+    - mm/numa: no task_numa_fault() call if PTE is changed
+    - Input: MT - limit max slots
+    - tools: move alignment-related macros to new <linux/align.h>
+    - btrfs: run delayed iputs when flushing delalloc
+    - pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins
+    - pinctrl: single: fix potential NULL dereference in pcs_get_function()
+    - wifi: mwifiex: duplicate static structs used in driver instances
+    - net: mana: Fix race of mana_hwc_post_rx_wqe and new hwc response
+    - mptcp: sched: check both backup in retrans
+    - Revert "MIPS: Loongson64: reset: Prioritise firmware service"
+    - drm/amdkfd: don't allow mapping the MMIO HDP page with large pages
+    - ata: libata-core: Fix null pointer dereference on error
+    - cgroup/cpuset: Prevent UAF in proc_cpuset_show()
+    - net:rds: Fix possible deadlock in rds_message_put
+    - soundwire: stream: fix programming slave ports for non-continous port maps
+    - PM: core: Remove DEFINE_UNIVERSAL_DEV_PM_OPS() macro
+    - PM: core: Add EXPORT[_GPL]_SIMPLE_DEV_PM_OPS macros
+    - PM: runtime: Add DEFINE_RUNTIME_DEV_PM_OPS() macro
+    - phy: xilinx: add runtime PM support
+    - phy: xilinx: phy-zynqmp: dynamic clock support for power-save
+    - phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
+    - dmaengine: dw: Add peripheral bus width verification
+    - dmaengine: dw: Add memory bus width verification
+    - ethtool: check device is present when getting link settings
+    - gtp: fix a potential NULL pointer dereference
+    - net: busy-poll: use ktime_get_ns() instead of local_clock()
+    - nfc: pn533: Add poll mod list filling check
+    - soc: qcom: cmd-db: Map shared memory as WC, not WB
+    - cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
+    - USB: serial: option: add MeiG Smart SRM825L
+    - usb: dwc3: omap: add missing depopulate in probe error path
+    - usb: dwc3: core: Prevent USB core invalid event buffer address access
+    - usb: dwc3: st: fix probed platform device ref count on probe error path
+    - usb: dwc3: st: add missing depopulate in probe error path
+    - usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in
+      remove_power_attributes()
+    - usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
+    - usb: cdnsp: fix for Link TRB with TC
+    - phy: zynqmp: Enable reference clock correctly
+    - igc: Fix reset adapter logics when tx mode change
+    - igc: Fix qbv tx latency by setting gtxoffset
+    - scsi: aacraid: Fix double-free on probe failure
+    - apparmor: fix policy_unpack_test on big endian systems
+    - Linux 5.15.166
+  * CVE-2024-26893
+    - firmware: arm_scmi: Fix double free in SMC transport cleanup path
+  * [22.10 FEAT] KVM: Secure Execution guest dump encryption with customer keys
+    - kernel part (LP: #1959940)
+    - s390: uv: Add offset comments to UV query struct and fix naming
+    - s390/uv: Add SE hdr query information
+    - s390/uv: Add dump fields to query
+    - KVM: s390: pv: Add query interface
+    - KVM: s390: pv: Add dump support definitions
+    - KVM: s390: pv: Add query dump information
+    - KVM: s390: Add configuration dump functionality
+    - KVM: s390: Add CPU dump functionality
+    - KVM: s390: Add KVM_CAP_S390_PROTECTED_DUMP
+    - Documentation: KVM: add separate directories for architecture-specific
+      documentation
+    - Documentation: virt: Protected virtual machine dumps
+    - Documentation/virt/kvm/api.rst: Add protvirt dump/info api descriptions
+    - Documentation/virt/kvm/api.rst: Explain rc/rrc delivery
+  * turbostat fails with too many open files on large systems (LP: #2069961)
+    - tools/power turbostat: Increase the limit for fd opened
+  * Jammy update: v5.15.165 upstream stable release (LP: #2078428)
+    - f2fs: fix return value of f2fs_convert_inline_inode()
+    - f2fs: fix to don't dirty inode for readonly filesystem
+    - EDAC, i10nm: make skx_common.o a separate module
+    - platform/chrome: cros_ec_debugfs: fix wrong EC message version
+    - block: refactor to use helper
+    - block: cleanup bio_integrity_prep
+    - block: initialize integrity buffer to zero before writing it to media
+    - hfsplus: fix to avoid false alarm of circular locking
+    - x86/of: Return consistent error type from x86_of_pci_irq_enable()
+    - x86/pci/intel_mid_pci: Fix PCIBIOS_* return code handling
+    - x86/pci/xen: Fix PCIBIOS_* return code handling
+    - x86/platform/iosf_mbi: Convert PCIBIOS_* return codes to errnos
+    - hwmon: (adt7475) Fix default duty on fan is disabled
+    - pwm: stm32: Always do lazy disabling
+    - drm/meson: fix canvas release in bind function
+    - hwmon: (max6697) Fix underflow when writing limit attributes
+    - hwmon: (max6697) Fix swapped temp{1,8} critical alarms
+    - arm64: dts: qcom: sdm845: add power-domain to UFS PHY
+    - arm64: dts: qcom: sm8250: switch UFS QMP PHY to new style of bindings
+    - arm64: dts: qcom: sm8250: add power-domain to UFS PHY
+    - soc: qcom: rpmh-rsc: Ensure irqs aren't disabled by rpmh_rsc_send_data()
+      callers
+    - arm64: dts: qcom: msm8996: specify UFS core_clk frequencies
+    - memory: fsl_ifc: Make FSL_IFC config visible and selectable
+    - soc: qcom: pdr: protect locator_addr with the main mutex
+    - soc: qcom: pdr: fix parsing of domains lists
+    - arm64: dts: rockchip: Increase VOP clk rate on RK3328
+    - ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node
+    - ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
+    - ARM: dts: imx6qdl-kontron-samx6i: fix board reset
+    - ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
+    - ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
+    - arm64: dts: mediatek: mt8183-kukui: Drop bogus output-enable property
+    - arm64: dts: mediatek: mt7622: fix "emmc" pinctrl mux
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add ports node for anx7625
+    - arm64: dts: amlogic: gx: correct hdmi clocks
+    - m68k: atari: Fix TT bootup freeze / unexpected (SCU) interrupt messages
+    - x86/xen: Convert comma to semicolon
+    - m68k: cmpxchg: Fix return value for default case in __arch_xchg()
+    - ARM: pxa: spitz: use gpio descriptors for audio
+    - ARM: spitz: fix GPIO assignment for backlight
+    - vmlinux.lds.h: catch .bss..L* sections into BSS")
+    - firmware: turris-mox-rwtm: Do not complete if there are no waiters
+    - firmware: turris-mox-rwtm: Fix checking return value of
+      wait_for_completion_timeout()
+    - firmware: turris-mox-rwtm: Initialize completion before mailbox
+    - wifi: brcmsmac: LCN PHY code is used for BCM4313 2G-only device
+    - selftests/bpf: Fix prog numbers in test_sockmap
+    - net: esp: cleanup esp_output_tail_tcp() in case of unsupported ESPINTCP
+    - tcp: annotate lockless accesses to sk->sk_err_soft
+    - tcp: annotate lockless access to sk->sk_err
+    - tcp: add tcp_done_with_error() helper
+    - tcp: fix race in tcp_write_err()
+    - tcp: fix races in tcp_v[46]_err()
+    - net/smc: set rmb's SG_MAX_SINGLE_ALLOC limitation only when
+      CONFIG_ARCH_NO_SG_CHAIN is defined
+    - selftests/bpf: Check length of recv in test_sockmap
+    - lib: objagg: Fix general protection fault
+    - mlxsw: spectrum_acl_erp: Fix object nesting warning
+    - mlxsw: spectrum_acl_bloom_filter: Make mlxsw_sp_acl_bf_key_encode() more
+      flexible
+    - mlxsw: spectrum_acl: Fix ACL scale regression and firmware errors
+    - wifi: ath11k: fix wrong handling of CCMP256 and GCMP ciphers
+    - wifi: cfg80211: fix typo in cfg80211_calculate_bitrate_he()
+    - wifi: cfg80211: handle 2x996 RU allocation in
+      cfg80211_calculate_bitrate_he()
+    - net: fec: Refactor: #define magic constants
+    - net: fec: Fix FEC_ECR_EN1588 being cleared on link-down
+    - libbpf: Checking the btf_type kind when fixing variable offsets
+    - ipvs: Avoid unnecessary calls to skb_is_gso_sctp
+    - netfilter: nf_tables: rise cap on SELinux secmark context
+    - perf/x86/intel/pt: Fix pt_topa_entry_for_page() address calculation
+    - perf: Fix perf_aux_size() for greater-than 32-bit size
+    - perf: Prevent passing zero nr_pages to rb_alloc_aux()
+    - perf: Fix default aux_watermark calculation
+    - wifi: virt_wifi: avoid reporting connection success with wrong SSID
+    - gss_krb5: Fix the error handling path for crypto_sync_skcipher_setkey
+    - wifi: virt_wifi: don't use strlen() in const context
+    - locking/rwsem: Add __always_inline annotation to __down_write_common() and
+      inlined callers
+    - selftests/bpf: Close fd in error path in drop_on_reuseport
+    - bpf: annotate BTF show functions with __printf
+    - bna: adjust 'name' buf size of bna_tcb and bna_ccb structures
+    - bpf: Eliminate remaining "make W=1" warnings in kernel/bpf/btf.o
+    - selftests: forwarding: devlink_lib: Wait for udev events after reloading
+    - xdp: fix invalid wait context of page_pool_destroy()
+    - drm/amd/pm: Fix aldebaran pcie speed reporting
+    - drm/amdgpu: Check if NBIO funcs are NULL in amdgpu_device_baco_exit
+    - drm/panel: boe-tv101wum-nl6: If prepare fails, disable GPIO before
+      regulators
+    - drm/panel: boe-tv101wum-nl6: Check for errors on the NOP in prepare()
+    - media: dvb-usb: Fix unexpected infinite loop in
+      dvb_usb_read_remote_control()
+    - media: imon: Fix race getting ictx->lock
+    - media: i2c: Fix imx412 exposure control
+    - saa7134: Unchecked i2c_transfer function result fixed
+    - media: uvcvideo: Override default flags
+    - media: renesas: vsp1: Fix _irqsave and _irq mix
+    - media: renesas: vsp1: Store RPF partition configuration per RPF instance
+    - drm/mediatek: Add missing plane settings when async update
+    - drm/mediatek: Add DRM_MODE_ROTATE_0 to rotation property
+    - leds: trigger: Unregister sysfs attributes before calling deactivate()
+    - perf report: Fix condition in sort__sym_cmp()
+    - drm/etnaviv: fix DMA direction handling for cached RW buffers
+    - drm/qxl: Add check for drm_cvt_mode
+    - Revert "leds: led-core: Fix refcount leak in of_led_get()"
+    - ext4: fix infinite loop when replaying fast_commit
+    - media: venus: flush all buffers in output plane streamoff
+    - perf intel-pt: Fix aux_watermark calculation for 64-bit size
+    - perf intel-pt: Fix exclude_guest setting
+    - mfd: rsmu: Split core code into separate module
+    - mfd: omap-usb-tll: Use struct_size to allocate tll
+    - xprtrdma: Fix rpcrdma_reqs_reset()
+    - SUNRPC: avoid soft lockup when transmitting UDP to reachable server.
+    - NFSv4.1 another fix for EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - ext4: return early for non-eligible fast_commit track events
+    - ext4: don't track ranges in fast_commit if inode has inlined data
+    - ext4: avoid writing unitialized memory to disk in EA inodes
+    - sparc64: Fix incorrect function signature and add prototype for
+      prom_cif_init
+    - SUNRPC: Fixup gss_status tracepoint error output
+    - PCI: Fix resource double counting on remove & rescan
+    - clk: qcom: branch: Add helper functions for setting retain bits
+    - clk: qcom: gcc-sc7280: Update force mem core bit for UFS ICE clock
+    - coresight: Fix ref leak when of_coresight_parse_endpoint() fails
+    - RDMA/mlx5: Set mkeys for dmabuf at PAGE_SIZE
+    - RDMA/cache: Release GID table even if leak is detected
+    - Input: qt1050 - handle CHIP_ID reading error
+    - RDMA/mlx4: Fix truncated output warning in mad.c
+    - RDMA/mlx4: Fix truncated output warning in alias_GUID.c
+    - RDMA/rxe: Don't set BTH_ACK_MASK for UC or UD QPs
+    - ASoC: max98088: Check for clk_prepare_enable() error
+    - mtd: make mtd_test.c a separate module
+    - RDMA/device: Return error earlier if port in not valid
+    - Input: elan_i2c - do not leave interrupt disabled on suspend failure
+    - PCI: endpoint: Clean up error handling in vpci_scan_bus()
+    - vhost/vsock: always initialize seqpacket_allow
+    - net: missing check virtio
+    - MIPS: Octeron: remove source file executable bit
+    - powerpc/xmon: Fix disassembly CPU feature checks
+    - macintosh/therm_windtunnel: fix module unload.
+    - RDMA/hns: Fix missing pagesize and alignment check in FRMR
+    - RDMA/hns: Fix undifined behavior caused by invalid max_sge
+    - RDMA/hns: Fix insufficient extend DB for VFs.
+    - bnxt_re: Fix imm_data endianness
+    - netfilter: ctnetlink: use helper function to calculate expect ID
+    - netfilter: nf_set_pipapo: fix initial map fill
+    - net: dsa: mv88e6xxx: Limit chip-wide frame size config to CPU ports
+    - net: dsa: b53: Limit chip-wide jumbo frame config to CPU ports
+    - fs/ntfs3: Use ALIGN kernel macro
+    - fs/ntfs3: Merge synonym COMPRESSION_UNIT and NTFS_LZNT_CUNIT
+    - fs/ntfs3: Fix transform resident to nonresident for compressed files
+    - fs/ntfs3: Missed NI_FLAG_UPDATE_PARENT setting
+    - fs/ntfs3: Fix getting file type
+    - pinctrl: rockchip: update rk3308 iomux routes
+    - pinctrl: core: fix possible memory leak when pinctrl_enable() fails
+    - pinctrl: single: fix possible memory leak when pinctrl_enable() fails
+    - pinctrl: ti: ti-iodelay: Drop if block with always false condition
+    - pinctrl: ti: ti-iodelay: fix possible memory leak when pinctrl_enable()
+      fails
+    - pinctrl: freescale: mxs: Fix refcount of child
+    - fs/ntfs3: Replace inode_trylock with inode_lock
+    - fs/ntfs3: Fix field-spanning write in INDEX_HDR
+    - fs/proc/task_mmu: indicate PM_FILE for PMD-mapped file THP
+    - nilfs2: avoid undefined behavior in nilfs_cnt32_ge macro
+    - rtc: interface: Add RTC offset to alarm after fix-up
+    - fs/ntfs3: Missed error return
+    - landlock: Don't lose track of restrictions on cred_transfer
+    - mm/hugetlb: fix possible recursive locking detected warning
+    - mm: mmap_lock: replace get_memcg_path_buf() with on-stack buffer
+    - dt-bindings: thermal: correct thermal zone node name limit
+    - tick/broadcast: Make takeover of broadcast hrtimer reliable
+    - net: netconsole: Disable target before netpoll cleanup
+    - af_packet: Handle outgoing VLAN packets without hardware offloading
+    - ipv6: take care of scope when choosing the src addr
+    - sched/fair: set_load_weight() must also call reweight_task() for SCHED_IDLE
+      tasks
+    - fuse: verify {g,u}id mount options correctly
+    - char: tpm: Fix possible memory leak in tpm_bios_measurements_open()
+    - media: venus: fix use after free in vdec_close
+    - ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error
+    - hfs: fix to initialize fields of hfs_inode_info after hfs_alloc_inode()
+    - ext2: Verify bitmap and itable block numbers before using them
+    - drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes
+    - drm/gma500: fix null pointer dereference in psb_intel_lvds_get_modes
+    - scsi: qla2xxx: Fix optrom version displayed in FDMI
+    - drm/amd/display: Check for NULL pointer
+    - sched/fair: Use all little CPUs for CPU-bound workloads
+    - apparmor: use kvfree_sensitive to free data->data
+    - task_work: s/task_work_cancel()/task_work_cancel_func()/
+    - task_work: Introduce task_work_cancel() again
+    - udf: Avoid using corrupted block bitmap buffer
+    - m68k: amiga: Turn off Warp1260 interrupts during boot
+    - ext4: check dot and dotdot of dx_root before making dir indexed
+    - ext4: make sure the first directory block is not a hole
+    - io_uring: tighten task exit cancellations
+    - selftests/landlock: Add cred_transfer test
+    - wifi: mwifiex: Fix interface type change
+    - leds: ss4200: Convert PCIBIOS_* return codes to errnos
+    - jbd2: make jbd2_journal_get_max_txn_bufs() internal
+    - media: uvcvideo: Fix integer overflow calculating timestamp
+    - KVM: VMX: Split out the non-virtualization part of vmx_interrupt_blocked()
+    - ALSA: usb-audio: Fix microphone sound on HD webcam.
+    - ALSA: usb-audio: Move HD Webcam quirk to the right place
+    - ALSA: usb-audio: Add a quirk for Sonix HD USB Camera
+    - tools/memory-model: Fix bug in lock.cat
+    - hwrng: amd - Convert PCIBIOS_* return codes to errnos
+    - PCI: hv: Return zero, not garbage, when reading PCI_INTERRUPT_PIN
+    - PCI: dw-rockchip: Fix initial PERST# GPIO value
+    - PCI: rockchip: Use GPIOD_OUT_LOW flag while requesting ep_gpio
+    - binder: fix hang of unregistered readers
+    - dev/parport: fix the array out-of-bounds risk
+    - fs/ntfs3: Update log->page_{mask,bits} if log->page_size changed
+    - scsi: qla2xxx: Return ENOBUFS if sg_cnt is more than one for ELS cmds
+    - clk: davinci: da8xx-cfgchip: Initialize clk_init_data before use
+    - ubi: eba: properly rollback inside self_check_eba
+    - decompress_bunzip2: fix rare decompression failure
+    - kbuild: Fix '-S -c' in x86 stack protector scripts
+    - kobject_uevent: Fix OOB access within zap_modalias_env()
+    - gve: Fix an edge case for TSO skb validity check
+    - devres: Fix devm_krealloc() wasting memory
+    - devres: Fix memory leakage caused by driver API devm_free_percpu()
+    - mm/numa_balancing: teach mpol_to_str about the balancing mode
+    - rtc: cmos: Fix return value of nvmem callbacks
+    - scsi: qla2xxx: During vport delete send async logout explicitly
+    - scsi: qla2xxx: Unable to act on RSCN for port online
+    - scsi: qla2xxx: Fix for possible memory corruption
+    - scsi: qla2xxx: Use QP lock to search for bsg
+    - scsi: qla2xxx: Fix flash read failure
+    - scsi: qla2xxx: Complete command early within lock
+    - scsi: qla2xxx: validate nvme_local_port correctly
+    - perf: Fix event leak upon exit
+    - perf: Fix event leak upon exec and file release
+    - perf/x86/intel/uncore: Fix the bits of the CHA extended umask for SPR
+    - perf/x86/intel/pt: Fix topa_entry base length
+    - perf/x86/intel/pt: Fix a topa_entry base address calculation
+    - drm/i915/gt: Do not consider preemption during execlists_dequeue for gen8
+    - drm/amdgpu/sdma5.2: Update wptr registers as well as doorbell
+    - drm/i915/dp: Reset intel_dp->link_trained before retraining the link
+    - rtc: isl1208: Fix return value of nvmem callbacks
+    - watchdog/perf: properly initialize the turbo mode timestamp and rearm
+      counter
+    - platform: mips: cpu_hwmon: Disable driver on unsupported hardware
+    - RDMA/iwcm: Fix a use-after-free related to destroying CM IDs
+    - selftests/sigaltstack: Fix ppc64 GCC build
+    - rbd: don't assume rbd_is_lock_owner() for exclusive mappings
+    - remoteproc: stm32_rproc: Fix mailbox interrupts queuing
+    - remoteproc: imx_rproc: Skip over memory region when node value is NULL
+    - MIPS: ip30: ip30-console: Add missing include
+    - MIPS: dts: loongson: Fix GMAC phy node
+    - MIPS: Loongson64: env: Hook up Loongsson-2K
+    - MIPS: Loongson64: Remove memory node for builtin-dtb
+    - MIPS: Loongson64: reset: Prioritise firmware service
+    - MIPS: Loongson64: Test register availability before use
+    - drm/panfrost: Mark simple_ondemand governor as softdep
+    - rbd: rename RBD_LOCK_STATE_RELEASING and releasing_wait
+    - rbd: don't assume RBD_LOCK_STATE_LOCKED for exclusive mappings
+    - Bluetooth: btusb: Add RTL8852BE device 0489:e125 to device tables
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x13d3:0x3591
+    - nilfs2: handle inconsistent state in nilfs_btnode_create_block()
+    - io_uring/io-wq: limit retrying worker initialisation
+    - kernel: rerun task_work while freezing in get_signal()
+    - kdb: address -Wformat-security warnings
+    - kdb: Use the passed prompt in kdb_position_cursor()
+    - jfs: Fix array-index-out-of-bounds in diFree
+    - dmaengine: ti: k3-udma: Fix BCHAN count with UHC and HC channels
+    - phy: cadence-torrent: Check return value on register read
+    - um: time-travel: fix time-travel-start option
+    - um: time-travel: fix signal blocking race/hang
+    - libbpf: Fix no-args func prototype BTF dumping syntax
+    - dma: fix call order in dmam_free_coherent
+    - bpf, events: Use prog to emit ksymbol event for main program
+    - MIPS: SMP-CPS: Fix address for GCR_ACCESS register for CM3 and later
+    - ipv4: Fix incorrect source address in Record Route option
+    - net: bonding: correctly annotate RCU in bond_should_notify_peers()
+    - netfilter: nft_set_pipapo_avx2: disable softinterrupts
+    - tipc: Return non-zero value from tipc_udp_addr2str() on error
+    - net: stmmac: Correct byte order of perfect_match
+    - net: nexthop: Initialize all fields in dumped nexthops
+    - bpf: Fix a segment issue when downgrading gso_size
+    - mISDN: Fix a use after free in hfcmulti_tx()
+    - apparmor: Fix null pointer deref when receiving skb during sock creation
+    - powerpc: fix a file leak in kvm_vcpu_ioctl_enable_cap()
+    - lirc: rc_dev_get_from_fd(): fix file leak
+    - spi: spidev: Make probe to fail early if a spidev compatible is used
+    - spi: spidev: Replace ACPI specific code by device_get_match_data()
+    - spi: spidev: Replace OF specific code by device property API
+    - spidev: Add Silicon Labs EM3581 device compatible
+    - spi: spidev: order compatibles alphabetically
+    - spi: spidev: add correct compatible for Rohm BH2228FV
+    - ASoC: Intel: use soc_intel_is_byt_cr() only when IOSF_MBI is reachable
+    - ceph: fix incorrect kmalloc size of pagevec mempool
+    - iommu: sprd: Avoid NULL deref in sprd_iommu_hw_en
+    - nvme: split command copy into a helper
+    - nvme: separate command prep and issue
+    - nvme-pci: add missing condition check for existence of mapped data
+    - fs: don't allow non-init s_user_ns for filesystems without FS_USERNS_MOUNT
+    - powerpc/configs: Update defconfig with now user-visible CONFIG_FSL_IFC
+    - arm64: dts: qcom: msm8996: Move '#clock-cells' to QMP PHY child node
+    - arm64: dts: qcom: msm8998: drop USB PHY clock index
+    - arm64: dts: qcom: msm8998: switch USB QMP PHY to new style of bindings
+    - arm64: dts: qcom: msm8998: Disable SS instance in Parkmode for USB
+    - arm64: dts: qcom: ipq8074: Disable SS instance in Parkmode for USB
+    - sysctl: always initialize i_uid/i_gid
+    - ext4: make ext4_es_insert_extent() return void
+    - ext4: refactor ext4_da_map_blocks()
+    - ext4: convert to exclusive lock while inserting delalloc extents
+    - ext4: factor out a common helper to query extent map
+    - ext4: check the extent status again before inserting delalloc block
+    - soc: xilinx: move PM_INIT_FINALIZE to zynqmp_pm_domains driver
+    - drivers: soc: xilinx: check return status of get_api_version()
+    - leds: trigger: use RCU to protect the led_cdevs list
+    - leds: trigger: Remove unused function led_trigger_rename_static()
+    - leds: trigger: Store brightness set by led_trigger_event()
+    - leds: trigger: Call synchronize_rcu() before calling trig->activate()
+    - leds: triggers: Flush pending brightness before activating trigger
+    - irqdomain: Fixed unbalanced fwnode get and put
+    - genirq: Allow the PM device to originate from irq domain
+    - irqchip/imx-irqsteer: Constify irq_chip struct
+    - irqchip/imx-irqsteer: Add runtime PM support
+    - irqchip/imx-irqsteer: Handle runtime power management correctly
+    - drm/dp_mst: Fix all mstb marked as not probed after suspend/resume
+    - remoteproc: imx_rproc: Fix refcount mistake in imx_rproc_addr_init
+    - MIPS: Loongson64: DTS: Add RTC support to Loongson-2K1000
+    - MIPS: Loongson64: DTS: Fix PCIe port nodes for ls7a
+    - MIPS: dts: loongson: Fix liointc IRQ polarity
+    - MIPS: dts: loongson: Fix ls2k1000-rtc interrupt
+    - drm/nouveau: prime: fix refcount underflow
+    - drm/vmwgfx: Fix overlay when using Screen Targets
+    - sched: act_ct: take care of padding in struct zones_ht_key
+    - ALSA: hda: conexant: Fix headset auto detect fail in the polling mode
+    - rtnetlink: enable alt_ifname for setlink/newlink
+    - rtnetlink: Don't ignore IFLA_TARGET_NETNSID when ifname is specified in
+      rtnl_dellink().
+    - net/iucv: fix use after free in iucv_sock_close()
+    - net: mvpp2: Don't re-use loop iterator
+    - netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init().
+    - netfilter: iptables: Fix potential null-ptr-deref in
+      ip6table_nat_table_init().
+    - net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptys
+    - ipv6: fix ndisc_is_useropt() handling for PIO
+    - riscv/mm: Add handling for VM_FAULT_SIGSEGV in mm_fault_error()
+    - power: supply: bq24190_charger: replace deprecated strncpy with strscpy
+    - platform/chrome: cros_ec_proto: Lock device when updating MKBP version
+    - HID: wacom: Modify pen IDs
+    - protect the fetch of ->fd[fd] in do_dup2() from mispredictions
+    - ALSA: usb-audio: Correct surround channels in UAC1 channel map
+    - ALSA: hda/realtek: Add quirk for Acer Aspire E5-574G
+    - Revert "ALSA: firewire-lib: obsolete workqueue for period update"
+    - Revert "ALSA: firewire-lib: operate for period elapse event in process
+      context"
+    - drm/vmwgfx: Fix a deadlock in dma buf fence polling
+    - net: usb: sr9700: fix uninitialized variable use in sr_mdio_read
+    - r8169: don't increment tx_dropped in case of NETDEV_TX_BUSY
+    - mptcp: fix duplicate data handling
+    - netfilter: ipset: Add list flush to cancel_gc
+    - genirq: Allow irq_chip registration functions to take a const irq_chip
+    - irqchip/mbigen: Fix mbigen node address layout
+    - x86/mm: Fix pti_clone_pgtable() alignment assumption
+    - x86/mm: Fix pti_clone_entry_text() for i386
+    - sctp: move hlist_node and hashent out of sctp_ep_common
+    - sctp: Fix null-ptr-deref in reuseport_add_sock().
+    - net: usb: qmi_wwan: fix memory leak for not ip packets
+    - net: bridge: mcast: wait for previous gc cycles when removing port
+    - net: linkwatch: use system_unbound_wq
+    - Bluetooth: l2cap: always unlock channel in l2cap_conless_channel()
+    - net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register()
+    - l2tp: fix lockdep splat
+    - net: fec: Stop PPS on driver remove
+    - rcutorture: Fix rcu_torture_fwd_cb_cr() data race
+    - md: do not delete safemode_timer in mddev_suspend
+    - md/raid5: avoid BUG_ON() while continue reshape after reassembling
+    - clocksource/drivers/sh_cmt: Address race condition for clock events
+    - ACPI: battery: create alarm sysfs attribute atomically
+    - ACPI: SBS: manage alarm sysfs attribute through psy core
+    - selftests/bpf: Fix send_signal test with nested CONFIG_PARAVIRT
+    - PCI: Add Edimax Vendor ID to pci_ids.h
+    - udf: prevent integer overflow in udf_bitmap_free_blocks()
+    - wifi: nl80211: don't give key data to userspace
+    - btrfs: fix bitmap leak when loading free space cache on duplicate entry
+    - drm/amdgpu/pm: Fix the null pointer dereference for smu7
+    - drm/amdgpu: Fix the null pointer dereference to ras_manager
+    - drm/amdgpu/pm: Fix the null pointer dereference in apply_state_adjust_rules
+    - drm/amd/display: Add null checker before passing variables
+    - media: uvcvideo: Ignore empty TS packets
+    - media: uvcvideo: Fix the bandwdith quirk on USB 3.x
+    - ext4: fix uninitialized variable in ext4_inlinedir_to_tree
+    - jbd2: avoid memleak in jbd2_journal_write_metadata_buffer
+    - s390/sclp: Prevent release of buffer in I/O
+    - SUNRPC: Fix a race to wake a sync task
+    - profiling: remove profile=sleep support
+    - scsi: mpt3sas: Avoid IOMMU page faults on REPORT ZONES
+    - sched/cputime: Fix mul_u64_u64_div_u64() precision for cputime
+    - ext4: fix wrong unit use in ext4_mb_find_by_goal
+    - arm64: cpufeature: Force HWCAP to be based on the sysreg visible to user-
+      space
+    - arm64: Add Neoverse-V2 part
+    - arm64: barrier: Restore spec_bar() macro
+    - arm64: cputype: Add Cortex-X4 definitions
+    - arm64: cputype: Add Neoverse-V3 definitions
+    - arm64: errata: Add workaround for Arm errata 3194386 and 3312417
+    - [Config] Set ARM64_ERRATUM_3194386=y
+    - arm64: cputype: Add Cortex-X3 definitions
+    - arm64: cputype: Add Cortex-A720 definitions
+    - arm64: cputype: Add Cortex-X925 definitions
+    - arm64: errata: Unify speculative SSBS errata logic
+    - arm64: errata: Expand speculative SSBS workaround
+    - arm64: cputype: Add Cortex-X1C definitions
+    - arm64: cputype: Add Cortex-A725 definitions
+    - arm64: errata: Expand speculative SSBS workaround (again)
+    - i2c: smbus: Improve handling of stuck alerts
+    - ASoC: codecs: wcd938x-sdw: Correct Soundwire ports mask
+    - ASoC: codecs: wsa881x: Correct Soundwire ports mask
+    - spi: spidev: Add missing spi_device_id for bh2228fv
+    - i2c: smbus: Send alert notifications to all devices if source not found
+    - bpf: kprobe: remove unused declaring of bpf_kprobe_override
+    - kprobes: Fix to check symbol prefixes correctly
+    - spi: spi-fsl-lpspi: Fix scldiv calculation
+    - ALSA: usb-audio: Re-add ScratchAmp quirk entries
+    - ASoC: meson: axg-fifo: fix irq scheduling issue with PREEMPT_RT
+    - drm/client: fix null pointer dereference in drm_client_modeset_probe
+    - ALSA: line6: Fix racy access to midibuf
+    - ALSA: hda: Add HP MP9 G4 Retail System AMS to force connect list
+    - ALSA: hda/hdmi: Yet more pin fix for HP EliteDesk 800 G4
+    - usb: vhci-hcd: Do not drop references before new references are gained
+    - USB: serial: debug: do not echo input by default
+    - usb: gadget: core: Check for unset descriptor
+    - usb: gadget: u_serial: Set start_delayed during suspend
+    - scsi: mpi3mr: Avoid IOMMU page faults on REPORT ZONES
+    - scsi: ufs: core: Fix hba->last_dme_cmd_tstamp timestamp updating logic
+    - tick/broadcast: Move per CPU pointer access into the atomic section
+    - vhost-vdpa: switch to use vmf_insert_pfn() in the fault handler
+    - ntp: Clamp maxerror and esterror to operating range
+    - clocksource: Reduce the default clocksource_watchdog() retries to 2
+    - torture: Enable clocksource watchdog with "tsc=watchdog"
+    - clocksource: Scale the watchdog read retries automatically
+    - clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()
+    - irqchip/meson-gpio: support more than 8 channels gpio irq
+    - irqchip/meson-gpio: Convert meson_gpio_irq_controller::lock to
+      'raw_spinlock_t'
+    - driver core: Fix uevent_show() vs driver detach race
+    - ntp: Safeguard against time_constant overflow
+    - timekeeping: Fix bogus clock_was_set() invocation in do_adjtimex()
+    - serial: core: check uartclk for zero to avoid divide by zero
+    - kcov: properly check for softirq context
+    - irqchip/xilinx: Fix shift out of bounds
+    - genirq/irqdesc: Honor caller provided affinity in alloc_desc()
+    - power: supply: axp288_charger: Fix constant_charge_voltage writes
+    - power: supply: axp288_charger: Round constant_charge_voltage writes down
+    - tracing: Fix overflow in get_free_elt()
+    - padata: Fix possible divide-by-0 panic in padata_mt_helper()
+    - x86/mtrr: Check if fixed MTRRs exist before saving them
+    - sched/smt: Introduce sched_smt_present_inc/dec() helper
+    - sched/smt: Fix unbalance sched_smt_present dec/inc
+    - drm/bridge: analogix_dp: properly handle zero sized AUX transactions
+    - drm/mgag200: Set DDC timeout in milliseconds
+    - mptcp: sched: check both directions for backup
+    - mptcp: distinguish rcv vs sent backup flag in requests
+    - mptcp: fix NL PM announced address accounting
+    - mptcp: mib: count MPJ with backup flag
+    - mptcp: fix bad RCVPRUNED mib accounting
+    - mptcp: pm: only set request_bkup flag when sending MP_PRIO
+    - mptcp: export local_address
+    - mptcp: pm: fix backup support in signal endpoints
+    - selftests: mptcp: join: validate backup in MPJ
+    - selftests: mptcp: join: check backup support in signal endp
+    - btrfs: fix corruption after buffer fault in during direct IO append write
+    - xfs: fix log recovery buffer allocation for the legacy h_size fixup
+    - btrfs: fix double inode unlock for direct IO sync writes
+    - PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal
+    - netfilter: nf_tables: set element extended ACK reporting support
+    - netfilter: nf_tables: bail out if stateful expression provides no .clone
+    - netfilter: nf_tables: allow clone callbacks to sleep
+    - netfilter: nf_tables: prefer nft_chain_validate
+    - net: stmmac: Enable mac_managed_pm phylink config
+    - PCI: dwc: Restore MSI Receiver mask during resume
+    - wifi: mac80211: check basic rates validity
+    - mptcp: fully established after ADD_ADDR echo on MPJ
+    - drm/i915/gem: Fix Virtual Memory mapping boundaries calculation
+    - powerpc: Avoid nmi_enter/nmi_exit in real mode interrupt.
+    - arm64: dts: qcom: msm8996: correct #clock-cells for QMP PHY nodes
+    - arm64: cpufeature: Fix the visibility of compat hwcaps
+    - exec: Fix ToCToU between perm check and set-uid/gid usage
+    - nvme/pci: Add APST quirk for Lenovo N60z laptop
+    - usb: gadget: u_audio: Check return codes from usb_ep_enable and
+      config_ep_by_speed.
+    - binfmt_flat: Fix corruption when not offsetting data start
+    - wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values
+    - ARM: dts: imx6qdl-kontron-samx6i: fix phy-mode
+    - media: Revert "media: dvb-usb: Fix unexpected infinite loop in
+      dvb_usb_read_remote_control()"
+    - Revert "ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error"
+    - Linux 5.15.165
+  * CVE-2024-26661
+    - drm/amd/display: Add NULL test for 'timing generator' in 'dcn21_set_pipe()'
+  * CVE-2024-25744
+    - x86: Fix misspelled Kconfig symbols
+    - x86: Introduce ia32_enabled()
+    - x86/sev: Rename mem_encrypt.c to mem_encrypt_amd.c
+    - x86/coco: Disable 32-bit emulation by default on TDX and SEV
+    - x86/entry: Convert INT 0x80 emulation to IDTENTRY
+    - x86/entry: Do not allow external 0x80 interrupts
+    - x86/entry: Add do_SYSENTER_32() prototype
+    - x86/bhi: Add support for clearing branch history at syscall entry
+  * [UBUNTU 22.04] s390/cpum_cf: make crypto counters upward compatible
+    (LP: #2074380)
+    - s390/cpum_cf: make crypto counters upward compatible across machine types
+  * Jammy update: v5.15.164 upstream stable release (LP: #2076100)
+    - gcc-plugins: Rename last_stmt() for GCC 14+
+    - filelock: Remove locks reliably when fcntl/close race is detected
+    - ARM: 9324/1: fix get_user() broken with veneer
+    - ACPI: processor_idle: Fix invalid comparison with insertion sort for latency
+    - scsi: core: Fix a use-after-free
+    - scsi: core: alua: I/O errors for ALUA state transitions
+    - scsi: qedf: Don't process stag work during unload and recovery
+    - scsi: qedf: Wait for stag work during unload
+    - scsi: qedf: Set qed_slowpath_params to zero before use
+    - ACPI: EC: Abort address space access upon error
+    - ACPI: EC: Avoid returning AE_OK on errors in address space handler
+    - tools/power/cpupower: Fix Pstate frequency reporting on AMD Family 1Ah CPUs
+    - wifi: mac80211: mesh: init nonpeer_pm to active by default in mesh sdata
+    - wifi: mac80211: handle tasklet frames before stopping
+    - wifi: iwlwifi: mvm: d3: fix WoWLAN command version lookup
+    - wifi: iwlwifi: mvm: Handle BIGTK cipher in kek_kck cmd
+    - wifi: iwlwifi: mvm: properly set 6 GHz channel direct probe option
+    - wifi: mac80211: fix UBSAN noise in ieee80211_prep_hw_scan()
+    - selftests/openat2: Fix build warnings on ppc64
+    - Input: silead - Always support 10 fingers
+    - net: ipv6: rpl_iptunnel: block BH in rpl_output() and rpl_input()
+    - ila: block BH in ila_output()
+    - arm64: armv8_deprecated: Fix warning in isndep cpuhp starting process
+    - null_blk: fix validation of block size
+    - kconfig: gconf: give a proper initial state to the Save button
+    - kconfig: remove wrong expr_trans_bool()
+    - fs/file: fix the check in find_next_fd()
+    - mei: demote client disconnect warning on suspend to debug
+    - nvme: avoid double free special payload
+    - wifi: cfg80211: wext: add extra SIOCSIWSCAN data check
+    - KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group()
+    - drm/vmwgfx: Fix missing HYPERVISOR_GUEST dependency
+    - ALSA: hda/realtek: Add more codec ID to no shutup pins list
+    - mips: fix compat_sys_lseek syscall
+    - Input: elantech - fix touchpad state on resume for Lenovo N24
+    - Input: i8042 - add Ayaneo Kun to i8042 quirk table
+    - bytcr_rt5640 : inverse jack detect for Archos 101 cesium
+    - ALSA: dmaengine: Synchronize dma channel after drop()
+    - ASoC: ti: davinci-mcasp: Set min period size using FIFO config
+    - ASoC: ti: omap-hdmi: Fix too long driver name
+    - can: kvaser_usb: fix return value for hif_usb_send_regout
+    - s390/sclp: Fix sclp_init() cleanup on failure
+    - platform/x86: wireless-hotkey: Add support for LG Airplane Button
+    - platform/x86: lg-laptop: Remove LGEX0815 hotkey handling
+    - platform/x86: lg-laptop: Change ACPI device id
+    - platform/x86: lg-laptop: Use ACPI device handle when evaluating WMAB/WMBB
+    - btrfs: qgroup: fix quota root leak after quota disable failure
+    - ALSA: hda/relatek: Enable Mute LED on HP Laptop 15-gw0xxx
+    - ALSA: dmaengine_pcm: terminate dmaengine before synchronize
+    - net: usb: qmi_wwan: add Telit FN912 compositions
+    - net: mac802154: Fix racy device stats updates by DEV_STATS_INC() and
+      DEV_STATS_ADD()
+    - powerpc/pseries: Whitelist dtl slub object for copying to userspace
+    - powerpc/eeh: avoid possible crash when edev->pdev changes
+    - scsi: libsas: Fix exp-attached device scan after probe failure scanned in
+      again after probe failed
+    - Bluetooth: hci_core: cancel all works upon hci_unregister_dev()
+    - drm/radeon: check bo_va->bo is non-NULL before using it
+    - fs: better handle deep ancestor chains in is_subdir()
+    - riscv: stacktrace: fix usage of ftrace_graph_ret_addr()
+    - spi: imx: Don't expect DMA for i.MX{25,35,50,51,53} cspi devices
+    - selftests/vDSO: fix clang build errors and warnings
+    - hfsplus: fix uninit-value in copy_name
+    - spi: mux: set ctlr->bits_per_word_mask
+    - tracing: Define the is_signed_type() macro once
+    - minmax: sanity check constant bounds when clamping
+    - minmax: clamp more efficiently by avoiding extra comparison
+    - minmax: fix header inclusions
+    - minmax: allow min()/max()/clamp() if the arguments have the same signedness.
+    - minmax: allow comparisons of 'int' against 'unsigned char/short'
+    - minmax: relax check to allow comparison between unsigned arguments and
+      signed constants
+    - mm/damon/core: merge regions aggressively when max_nr_regions is unmet
+    - wifi: mac80211: disable softirqs for queued frame handling
+    - drm/amdgpu: Fix signedness bug in sdma_v4_0_process_trap_irq()
+    - samples: Add fs error monitoring example
+    - samples: Make fs-monitor depend on libc and headers
+    - docs: Fix formatting of literal sections in fanotify docs
+    - Add gitignore file for samples/fanotify/ subdirectory
+    - net: relax socket state check at accept time.
+    - ocfs2: add bounds checking to ocfs2_check_dir_entry()
+    - jfs: don't walk off the end of ealist
+    - fs/ntfs3: Validate ff offset
+    - ALSA: hda/realtek: Enable headset mic on Positivo SU C1400
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
+    - arm64: dts: qcom: msm8996: Disable SS instance in Parkmode for USB
+    - arm64: dts: qcom: sdm630: Disable SS instance in Parkmode for USB
+    - ALSA: pcm_dmaengine: Don't synchronize DMA channel when DMA is paused
+    - filelock: Fix fcntl/close race recovery compat path
+    - wifi: rt2x00: use explicitly signed or unsigned types
+    - tun: add missing verification for short frame
+    - tap: add missing verification for short frame
+    - Linux 5.15.164
+  * Jammy update: v5.15.166 upstream stable release (LP: #2080594) //
+    CVE-2024-45016
+    - netem: fix return value if duplicate enqueue fails
+  * CVE-2024-38630
+    - watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
+  * CVE-2024-27397
+    - netfilter: nf_tables: use timestamp to check for set element timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 09 Oct 2024 09:43:42 +1000
+
+linux-xilinx-zynqmp (5.15.0-1037.41) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1037.41 -proposed tracker (LP: #2082173)
+
+  [ Ubuntu: 5.15.0-124.134 ]
+
+  * jammy/linux: 5.15.0-124.134 -proposed tracker (LP: #2082176)
+  * CVE-2024-45016
+    - netem: fix return value if duplicate enqueue fails
+  * CVE-2024-38630
+    - watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
+  * CVE-2024-27397
+    - netfilter: nf_tables: use timestamp to check for set element timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 04 Oct 2024 08:16:14 +1000
+
+linux-xilinx-zynqmp (5.15.0-1036.40) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1036.40 -proposed tracker (LP: #2078151)
+
+  [ Ubuntu: 5.15.0-122.132 ]
+
+  * jammy/linux: 5.15.0-122.132 -proposed tracker (LP: #2078154)
+  * isolcpus are ignored when using cgroups V2, causing processes to have wrong
+    affinity (LP: #2076957)
+    - cgroup/cpuset: Optimize cpuset_attach() on v2
+  * Jammy update: v5.15.164 upstream stable release (LP: #2076100) //
+    CVE-2024-41009
+    - bpf: Fix overrunning reservations in ringbuf
+  * CVE-2024-39494
+    - ima: Fix use-after-free on a dentry's dname.name
+  * CVE-2024-39496
+    - btrfs: zoned: fix use-after-free due to race with dev replace
+  * CVE-2024-42160
+    - f2fs: check validation of fault attrs in f2fs_build_fault_attr()
+    - f2fs: Add inline to f2fs_build_fault_attr() stub
+  * CVE-2024-38570
+    - gfs2: Rename sd_{ glock => kill }_wait
+    - gfs2: Fix potential glock use-after-free on unmount
+  * CVE-2024-42228
+    - drm/amdgpu: Using uninitialized value *size when calling amdgpu_vce_cs_reloc
+  * CVE-2024-27012
+    - netfilter: nf_tables: restore set elements when delete set fails
+  * CVE-2024-26677
+    - rxrpc: Fix delayed ACKs to not set the reference serial number
+
+ -- Roxana Nicolescu <roxana.nicolescu@canonical.com>  Tue, 03 Sep 2024 14:32:49 +0200
+
+linux-xilinx-zynqmp (5.15.0-1035.39) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1035.39 -proposed tracker (LP: #2077835)
+
+  * Backport ps uart  RS485  driver  (LP: #2055237)
+    - dt-bindings: serial: cdsn,uart: add power-domains
+    - dt-bindings: Add reference to rs485.yaml
+    - serial: Store character timing information to uart_port
+    - serial: take termios_rwsem for ->rs485_config() & pass termios as param
+    - tty: serial: uartps: Relocate cdns_uart_tx_empty to facilitate rs485
+    - tty: serial: uartps: Add rs485 support to uartps driver
+    - dt-bindings: serial: cdns,uart: Add optional reset property
+    - arm64: zynqmp: Add resets property for UART nodes
+    - tty: serial: uartps: Add support for uartps controller reset
+    - SAUCE: dts: zynqmp-sck-kd-g-revA: Enable uart0 for KD240
+    - SAUCE: arm64: zynqmp: dts: Add required properties for rs485 support for
+      KD240
+    - SAUCE: arm64: zynqmp: dts: Add rts delay property for rs485 mode on KD240
+    - serial: 8250: Document termios parameter of serial8250_em485_config()
+    - serial: fix TIOCSRS485 locking
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Mon, 26 Aug 2024 09:21:51 +1000
+
+linux-xilinx-zynqmp (5.15.0-1034.38) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1034.38 -proposed tracker (LP: #2075900)
+
+  * Update IMX547 out-of-tree driver code (LP: #2076108)
+    - SAUCE: imx547 : Used devm_* resource management functions instead of gpiod_*
+
+  [ Ubuntu: 5.15.0-121.131 ]
+
+  * jammy/linux: 5.15.0-121.131 -proposed tracker (LP: #2076347)
+  * jammy:linux bpf selftest do not build (LP: #2076334)
+    - SAUCE: Revert "bpf: Allow reads from uninit stack"
+
+  [ Ubuntu: 5.15.0-120.130 ]
+
+  * jammy/linux: 5.15.0-120.130 -proposed tracker (LP: #2075903)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2024.08.05)
+  * Jammy update: v5.15.163 upstream stable release (LP: #2075170)
+    - Compiler Attributes: Add __uninitialized macro
+    - locking/mutex: Introduce devm_mutex_init()
+    - drm/lima: fix shared irq handling on driver remove
+    - media: dvb: as102-fe: Fix as10x_register_addr packing
+    - media: dvb-usb: dib0700_devices: Add missing release_firmware()
+    - IB/core: Implement a limit on UMAD receive List
+    - scsi: qedf: Make qedf_execute_tmf() non-preemptible
+    - crypto: aead,cipher - zeroize key buffer after use
+    - drm/amdgpu: Initialize timestamp for some legacy SOCs
+    - drm/amd/display: Check index msg_id before read or write
+    - drm/amd/display: Check pipe offset before setting vblank
+    - drm/amd/display: Skip finding free audio for unknown engine_id
+    - media: dw2102: Don't translate i2c read into write
+    - sctp: prefer struct_size over open coded arithmetic
+    - firmware: dmi: Stop decoding on broken entry
+    - Input: ff-core - prefer struct_size over open coded arithmetic
+    - wifi: mt76: replace skb_put with skb_put_zero
+    - net: dsa: mv88e6xxx: Correct check for empty list
+    - media: dvb-frontends: tda18271c2dd: Remove casting during div
+    - media: s2255: Use refcount_t instead of atomic_t for num_channels
+    - media: dvb-frontends: tda10048: Fix integer overflow
+    - i2c: i801: Annotate apanel_addr as __ro_after_init
+    - powerpc/64: Set _IO_BASE to POISON_POINTER_DELTA not 0 for CONFIG_PCI=n
+    - orangefs: fix out-of-bounds fsid access
+    - kunit: Fix timeout message
+    - powerpc/xmon: Check cpu id in commands "c#", "dp#" and "dx#"
+    - igc: fix a log entry using uninitialized netdev
+    - bpf: Avoid uninitialized value in BPF_CORE_READ_BITFIELD
+    - jffs2: Fix potential illegal address access in jffs2_free_inode
+    - s390/pkey: Wipe sensitive data on failure
+    - tools/power turbostat: Remember global max_die_id
+    - UPSTREAM: tcp: fix DSACK undo in fast recovery to call tcp_try_to_open()
+    - tcp_metrics: validate source addr length
+    - KVM: s390: fix LPSWEY handling
+    - e1000e: Fix S0ix residency on corporate systems
+    - net: allow skb_datagram_iter to be called from any context
+    - wifi: wilc1000: fix ies_len type in connect path
+    - riscv: kexec: Avoid deadlock in kexec crash path
+    - netfilter: nf_tables: unconditionally flush pending work before notifier
+    - bonding: Fix out-of-bounds read in bond_option_arp_ip_targets_set()
+    - selftests: fix OOM in msg_zerocopy selftest
+    - selftests: make order checking verbose in msg_zerocopy selftest
+    - inet_diag: Initialize pad field in struct inet_diag_req_v2
+    - gpiolib: of: factor out code overriding gpio line polarity
+    - gpiolib: of: add a quirk for reset line polarity for Himax LCDs
+    - gpiolib: of: add polarity quirk for TSC2005
+    - Revert "igc: fix a log entry using uninitialized netdev"
+    - nilfs2: fix inode number range checks
+    - nilfs2: add missing check for inode numbers on directory entries
+    - mm: optimize the redundant loop of mm_update_owner_next()
+    - mm: avoid overflows in dirty throttling logic
+    - btrfs: fix adding block group to a reclaim list and the unused list during
+      reclaim
+    - Bluetooth: qca: Fix BT enable failure again for QCA6390 after warm reboot
+    - can: kvaser_usb: Explicitly initialize family in leafimx driver_info struct
+    - fsnotify: Do not generate events for O_PATH file descriptors
+    - Revert "mm/writeback: fix possible divide-by-zero in wb_dirty_limits(),
+      again"
+    - drm/nouveau: fix null pointer dereference in nouveau_connector_get_modes
+    - drm/amdgpu/atomfirmware: silence UBSAN warning
+    - mtd: rawnand: Ensure ECC configuration is propagated to upper layers
+    - mtd: rawnand: Bypass a couple of sanity checks during NAND identification
+    - mtd: rawnand: rockchip: ensure NVDDR timings are rejected
+    - ima: Avoid blocking in RCU read-side critical section
+    - media: dw2102: fix a potential buffer overflow
+    - clk: qcom: gcc-sm6350: Fix gpll6* & gpll7 parents
+    - i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr
+    - fs/ntfs3: Mark volume as dirty if xattr is broken
+    - ALSA: hda/realtek: Enable headset mic of JP-IK LEAP W502 with ALC897
+    - nvme-multipath: find NUMA path only for online numa-node
+    - dma-mapping: benchmark: avoid needless copy_to_user if benchmark fails
+    - nvme: adjust multiples of NVME_CTRL_PAGE_SIZE in offset
+    - regmap-i2c: Subtract reg size from max_write
+    - platform/x86: touchscreen_dmi: Add info for GlobalSpace SolT IVW 11.6"
+      tablet
+    - platform/x86: touchscreen_dmi: Add info for the EZpad 6s Pro
+    - nvmet: fix a possible leak when destroy a ctrl during qp establishment
+    - kbuild: fix short log for AS in link-vmlinux.sh
+    - nfc/nci: Add the inconsistency check between the input data length and count
+    - null_blk: Do not allow runt zone with zone capacity smaller then zone size
+    - nilfs2: fix incorrect inode allocation from reserved inodes
+    - mm: prevent derefencing NULL ptr in pfn_section_valid()
+    - filelock: fix potential use-after-free in posix_lock_inode
+    - fs/dcache: Re-use value stored to dentry->d_flags instead of re-reading
+    - vfs: don't mod negative dentry count when on shrinker list
+    - tcp: fix incorrect undo caused by DSACK of TLP retransmit
+    - skmsg: Skip zero length skb in sk_msg_recvmsg
+    - octeontx2-af: Fix incorrect value output on error path in
+      rvu_check_rsrc_availability()
+    - net: fix rc7's __skb_datagram_iter()
+    - i40e: Fix XDP program unloading while removing the driver
+    - net: lantiq_etop: add blank line after declaration
+    - net: ethernet: lantiq_etop: fix double free in detach
+    - net: ethernet: mtk-star-emac: set mac_managed_pm when probing
+    - ppp: reject claimed-as-LCP but actually malformed packets
+    - ethtool: netlink: do not return SQI value if link is down
+    - udp: Set SOCK_RCU_FREE earlier in udp_lib_get_port().
+    - s390: Mark psw in __load_psw_mask() as __unitialized
+    - ARM: davinci: Convert comma to semicolon
+    - octeontx2-af: replace cpt slot with lf id on reg write
+    - octeontx2-af: update cpt lf alloc mailbox
+    - octeontx2-af: fix a issue with cpt_lf_alloc mailbox
+    - octeontx2-af: fix detection of IP layer
+    - octeontx2-af: extend RSS supported offload types
+    - octeontx2-af: fix issue with IPv6 ext match for RSS
+    - octeontx2-af: fix issue with IPv4 match for RSS
+    - tcp: use signed arithmetic in tcp_rtx_probe0_timed_out()
+    - tcp: avoid too many retransmit packets
+    - net: ks8851: Fix potential TX stall after interface reopen
+    - USB: serial: option: add Telit generic core-dump composition
+    - USB: serial: option: add Telit FN912 rmnet compositions
+    - USB: serial: option: add Fibocom FM350-GL
+    - USB: serial: option: add support for Foxconn T99W651
+    - USB: serial: option: add Netprisma LCUK54 series modules
+    - USB: serial: option: add Rolling RW350-GL variants
+    - USB: serial: mos7840: fix crash on resume
+    - USB: Add USB_QUIRK_NO_SET_INTF quirk for START BP-850k
+    - usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()
+    - USB: core: Fix duplicate endpoint bug by clearing reserved bits in the
+      descriptor
+    - hpet: Support 32-bit userspace
+    - nvmem: rmem: Fix return value of rmem_read()
+    - nvmem: meson-efuse: Fix return value of nvmem callbacks
+    - nvmem: core: only change name to fram for current attribute
+    - ALSA: hda/realtek: add quirk for Clevo V5[46]0TU
+    - ALSA: hda/realtek: Enable Mute LED on HP 250 G7
+    - ALSA: hda/realtek: Limit mic boost on VAIO PRO PX
+    - Fix userfaultfd_api to return EINVAL as expected
+    - libceph: fix race between delayed_work() and ceph_monc_stop()
+    - wireguard: allowedips: avoid unaligned 64-bit memory accesses
+    - wireguard: queueing: annotate intentional data race in cpu round robin
+    - wireguard: send: annotate intentional data race in checking empty queue
+    - ipv6: annotate data-races around cnf.disable_ipv6
+    - bpf: Allow reads from uninit stack
+    - nilfs2: fix kernel bug on rename operation of broken directory
+    - i2c: rcar: bring hardware to known state when probing
+    - i2c: mark HostNotify target address as used
+    - i2c: rcar: Add R-Car Gen4 support
+    - i2c: rcar: reset controller is mandatory for Gen3+
+    - i2c: rcar: introduce Gen4 devices
+    - i2c: rcar: ensure Gen3+ reset does not disturb local targets
+    - i2c: testunit: avoid re-issued work after read message
+    - i2c: rcar: clear NO_RXDMA flag after resetting
+    - x86/entry/64: Remove obsolete comment on tracing vs. SYSRET
+    - x86/bhi: Avoid warning in #DB handler due to BHI mitigation
+    - kbuild: Make ld-version.sh more robust against version string changes
+    - i2c: rcar: fix error code in probe()
+    - Linux 5.15.163
+  * [SRU] UBSAN warnings in bnx2x kernel driver (LP: #2074215) // Jammy update:
+    v5.15.163 upstream stable release (LP: #2075170)
+    - bnx2x: Fix multiple UBSAN array-index-out-of-bounds
+  * Jammy update: v5.15.162 upstream stable release (LP: #2073765)
+    - mmc: davinci_mmc: Convert to platform remove callback returning void
+    - wifi: mac80211: mesh: Fix leak of mesh_preq_queue objects
+    - wifi: mac80211: Fix deadlock in ieee80211_sta_ps_deliver_wakeup()
+    - wifi: cfg80211: Lock wiphy in cfg80211_get_station
+    - wifi: cfg80211: pmsr: use correct nla_get_uX functions
+    - wifi: iwlwifi: mvm: revert gen2 TX A-MPDU size to 64
+    - wifi: iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
+    - wifi: iwlwifi: mvm: check n_ssids before accessing the ssids
+    - wifi: iwlwifi: mvm: don't read past the mfuart notifcation
+    - wifi: mac80211: correctly parse Spatial Reuse Parameter Set element
+    - net/ncsi: Simplify Kconfig/dts control flow
+    - net/ncsi: Fix the multi thread manner of NCSI driver
+    - ipv6: sr: block BH in seg6_output_core() and seg6_input_core()
+    - bpf: Set run context for rawtp test_run callback
+    - octeontx2-af: Always allocate PF entries from low prioriy zone
+    - net: sched: sch_multiq: fix possible OOB write in multiq_tune()
+    - vxlan: Fix regression when dropping packets due to invalid src addresses
+    - tcp: count CLOSE-WAIT sockets for TCP_MIB_CURRESTAB
+    - net/sched: taprio: always validate TCA_TAPRIO_ATTR_PRIOMAP
+    - ptp: Fix error message on failed pin verification
+    - af_unix: Set sk->sk_state under unix_state_lock() for truly disconencted
+      peer.
+    - af_unix: Annodate data-races around sk->sk_state for writers.
+    - af_unix: Annotate data-race of sk->sk_state in unix_inq_len().
+    - af_unix: Annotate data-races around sk->sk_state in unix_write_space() and
+      poll().
+    - net: inline sock_prot_inuse_add()
+    - net: drop nopreempt requirement on sock_prot_inuse_add()
+    - af_unix: Annotate data-race of sk->sk_state in unix_stream_connect().
+    - af_unix: Annotate data-races around sk->sk_state in sendmsg() and recvmsg().
+    - af_unix: Annotate data-race of sk->sk_state in unix_stream_read_skb().
+    - af_unix: Annotate data-races around sk->sk_state in UNIX_DIAG.
+    - af_unix: Annotate data-race of net->unx.sysctl_max_dgram_qlen.
+    - af_unix: Use unix_recvq_full_lockless() in unix_stream_connect().
+    - af_unix: annotate lockless accesses to sk->sk_err
+    - af_unix: Use skb_queue_empty_lockless() in unix_release_sock().
+    - af_unix: Use skb_queue_len_lockless() in sk_diag_show_rqlen().
+    - af_unix: Annotate data-race of sk->sk_shutdown in sk_diag_fill().
+    - ipv6: fix possible race in __fib6_drop_pcpu_from()
+    - usb: gadget: f_fs: use io_data->status consistently
+    - usb: gadget: f_fs: Fix race between aio_cancel() and AIO request complete
+    - iio: accel: mxc4005: Reset chip on probe() and resume()
+    - drm/amd/display: Handle Y carry-over in VCP X.Y calculation
+    - drm/amd/display: Clean up some inconsistent indenting
+    - drm/amd/display: drop unnecessary NULL checks in debugfs
+    - drm/amd/display: Fix incorrect DSC instance for MST
+    - pvpanic: Keep single style across modules
+    - pvpanic: Indentation fixes here and there
+    - misc/pvpanic: deduplicate common code
+    - misc/pvpanic-pci: register attributes via pci_driver
+    - skbuff: introduce skb_pull_data
+    - Bluetooth: hci_qca: mark OF related data as maybe unused
+    - Bluetooth: btqca: use le32_to_cpu for ver.soc_id
+    - Bluetooth: btqca: Add WCN3988 support
+    - Bluetooth: qca: use switch case for soc type behavior
+    - Bluetooth: qca: add support for QCA2066
+    - Bluetooth: qca: fix info leak when fetching fw build id
+    - serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
+    - serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
+    - x86/ibt,ftrace: Search for __fentry__ location
+    - ftrace: Fix possible use-after-free issue in ftrace_location()
+    - i2c: add fwnode APIs
+    - i2c: acpi: Unbind mux adapters before delete
+    - cma: factor out minimum alignment requirement
+    - mm/cma: drop incorrect alignment check in cma_init_reserved_mem
+    - selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
+    - selftests/mm: conform test to TAP format output
+    - selftests/mm: compaction_test: fix bogus test success on Aarch64
+    - wifi: ath10k: fix QCOM_RPROC_COMMON dependency
+    - btrfs: fix leak of qgroup extent records after transaction abort
+    - nilfs2: Remove check for PageError
+    - nilfs2: return the mapped address from nilfs_get_page()
+    - nilfs2: fix nilfs_empty_dir() misjudgment and long loop on I/O errors
+    - USB: class: cdc-wdm: Fix CPU lockup caused by excessive log messages
+    - usb: typec: tcpm: Ignore received Hard Reset in TOGGLING state
+    - mei: me: release irq in mei_me_pci_resume error path
+    - jfs: xattr: fix buffer overflow for invalid xattr
+    - xhci: Set correct transferred length for cancelled bulk transfers
+    - xhci: Apply reset resume quirk to Etron EJ188 xHCI host
+    - xhci: Handle TD clearing for multiple streams case
+    - xhci: Apply broken streams quirk to Etron EJ188 xHCI host
+    - scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
+    - powerpc/uaccess: Fix build errors seen with GCC 13/14
+    - Input: try trimming too long modalias strings
+    - clk: sifive: Do not register clkdevs for PRCI clocks
+    - SUNRPC: return proper error from gss_wrap_req_priv
+    - platform/x86: dell-smbios-base: Use sysfs_emit()
+    - platform/x86: dell-smbios: Fix wrong token data in sysfs
+    - gpio: tqmx86: fix typo in Kconfig label
+    - gpio: tqmx86: store IRQ trigger type and unmask status separately
+    - HID: core: remove unnecessary WARN_ON() in implement()
+    - iommu/amd: Introduce pci segment structure
+    - iommu/amd: Fix sysfs leak in iommu init
+    - iommu: Return right value in iommu_sva_bind_device()
+    - HID: logitech-dj: Fix memory leak in logi_dj_recv_switch_to_dj_mode()
+    - drm/vmwgfx: 3D disabled should not effect STDU memory limits
+    - net: sfp: Always call `sfp_sm_mod_remove()` on remove
+    - net: hns3: fix kernel crash problem in concurrent scenario
+    - net: hns3: add cond_resched() to hns3 ring buffer init process
+    - liquidio: Adjust a NULL pointer handling path in lio_vf_rep_copy_packet
+    - drm/komeda: check for error-valued pointer
+    - drm/bridge/panel: Fix runtime warning on panel bridge release
+    - tcp: fix race in tcp_v6_syn_recv_sock()
+    - net/mlx5e: Fix features validation check for tunneled UDP (non-VXLAN)
+      packets
+    - netfilter: ipset: Fix race between namespace cleanup and gc in the list:set
+      type
+    - net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs
+      parameters
+    - net/ipv6: Fix the RT cache flush via sysctl using a previous delay
+    - ionic: fix use after netif_napi_del()
+    - af_unix: Read with MSG_PEEK loops if the first unread byte is OOB
+    - iio: adc: ad9467: fix scan type sign
+    - iio: dac: ad5592r: fix temperature channel scaling value
+    - iio: imu: inv_icm42600: delete unneeded update watermark call
+    - drivers: core: synchronize really_probe() and dev_uevent()
+    - drm/exynos/vidi: fix memory leak in .get_modes()
+    - drm/exynos: hdmi: report safe 640x480 mode as a fallback when no EDID found
+    - mptcp: ensure snd_una is properly initialized on connect
+    - tracing/selftests: Fix kprobe event name test for .isra. functions
+    - null_blk: Print correct max open zones limit in null_init_zoned_dev()
+    - sock_map: avoid race between sock_map_close and sk_psock_put
+    - vmci: prevent speculation leaks by sanitizing event in event_deliver()
+    - spmi: hisi-spmi-controller: Do not override device identifier
+    - knfsd: LOOKUP can return an illegal error value
+    - fs/proc: fix softlockup in __read_vmcore
+    - ocfs2: use coarse time for new created files
+    - ocfs2: fix races between hole punching and AIO+DIO
+    - PCI: rockchip-ep: Remove wrong mask on subsys_vendor_id
+    - dmaengine: axi-dmac: fix possible race in remove()
+    - intel_th: pci: Add Granite Rapids support
+    - intel_th: pci: Add Granite Rapids SOC support
+    - intel_th: pci: Add Sapphire Rapids SOC support
+    - intel_th: pci: Add Meteor Lake-S support
+    - intel_th: pci: Add Lunar Lake support
+    - nilfs2: fix potential kernel bug due to lack of writeback flag waiting
+    - tick/nohz_full: Don't abuse smp_call_function_single() in
+      tick_setup_device()
+    - scsi: mpi3mr: Fix ATA NCQ priority support
+    - mm/huge_memory: don't unpoison huge_zero_folio
+    - serial: 8250_pxa: Configure tx_loadsz to match FIFO IRQ level
+    - hugetlb_encode.h: fix undefined behaviour (34 << 26)
+    - mptcp: pm: inc RmAddr MIB counter once per RM_ADDR ID
+    - mptcp: pm: update add_addr counters after connect
+    - kbuild: Remove support for Clang's ThinLTO caching
+    - greybus: Fix use-after-free bug in gb_interface_release due to race
+      condition.
+    - usb-storage: alauda: Check whether the media is initialized
+    - i2c: at91: Fix the functionality flags of the slave-only interface
+    - i2c: designware: Fix the functionality flags of the slave-only interface
+    - zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
+    - Bluetooth: qca: Fix error code in qca_read_fw_build_info()
+    - Bluetooth: qca: fix info leak when fetching board id
+    - padata: Disable BH when taking works lock on MT path
+    - crypto: hisilicon/sec - Fix memory leak for sec resource release
+    - rcutorture: Fix rcu_torture_one_read() pipe_count overflow comment
+    - rcutorture: Make stall-tasks directly exit when rcutorture tests end
+    - rcutorture: Fix invalid context warning when enable srcu barrier testing
+    - block/ioctl: prefer different overflow check
+    - selftests/bpf: Prevent client connect before server bind in
+      test_tc_tunnel.sh
+    - selftests/bpf: Fix flaky test btf_map_in_map/lookup_update
+    - batman-adv: bypass empty buckets in batadv_purge_orig_ref()
+    - wifi: ath9k: work around memset overflow warning
+    - af_packet: avoid a false positive warning in packet_setsockopt()
+    - drop_monitor: replace spin_lock by raw_spin_lock
+    - scsi: qedi: Fix crash while reading debugfs attribute
+    - kselftest: arm64: Add a null pointer check
+    - netpoll: Fix race condition in netpoll_owner_active
+    - HID: Add quirk for Logitech Casa touchpad
+    - ACPI: video: Add backlight=native quirk for Lenovo Slim 7 16ARH7
+    - Bluetooth: ath3k: Fix multiple issues reported by checkpatch.pl
+    - drm/amd/display: Exit idle optimizations before HDCP execution
+    - drm/lima: add mask irq callback to gp and pp
+    - drm/lima: mask irqs in timeout path before hard reset
+    - powerpc/pseries: Enforce hcall result buffer validity and size
+    - powerpc/io: Avoid clang null pointer arithmetic warnings
+    - power: supply: cros_usbpd: provide ID table for avoiding fallback match
+    - iommu/arm-smmu-v3: Free MSIs in case of ENOMEM
+    - f2fs: remove clear SB_INLINECRYPT flag in default_options
+    - usb: misc: uss720: check for incompatible versions of the Belkin F5U002
+    - Avoid hw_desc array overrun in dw-axi-dmac
+    - udf: udftime: prevent overflow in udf_disk_stamp_to_time()
+    - PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports
+    - MIPS: Octeon: Add PCIe link status check
+    - serial: imx: Introduce timeout when waiting on transmitter empty
+    - serial: exar: adding missing CTI and Exar PCI ids
+    - MIPS: Routerboard 532: Fix vendor retry check code
+    - mips: bmips: BCM6358: make sure CBR is correctly set
+    - tracing: Build event generation tests only as modules
+    - cipso: fix total option length computation
+    - netrom: Fix a memory leak in nr_heartbeat_expiry()
+    - ipv6: prevent possible NULL deref in fib6_nh_init()
+    - ipv6: prevent possible NULL dereference in rt6_probe()
+    - xfrm6: check ip6_dst_idev() return value in xfrm6_get_saddr()
+    - netns: Make get_net_ns() handle zero refcount net
+    - qca_spi: Make interrupt remembering atomic
+    - net/sched: act_api: rely on rcu in tcf_idr_check_alloc
+    - net/sched: act_api: fix possible infinite loop in tcf_idr_check_alloc()
+    - tipc: force a dst refcount before doing decryption
+    - net/sched: act_ct: set 'net' pointer when creating new nf_flow_table
+    - sched: act_ct: add netns into the key of tcf_ct_flow_table
+    - ptp: fix integer overflow in max_vclocks_store
+    - net: stmmac: No need to calculate speed divider when offload is disabled
+    - virtio_net: checksum offloading handling fix
+    - octeontx2-pf: Add error handling to VLAN unoffload handling
+    - netfilter: ipset: Fix suspicious rcu_dereference_protected()
+    - seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6
+      behaviors
+    - bnxt_en: Restore PTP tx_avail count in case of skb_pad() error
+    - net: usb: rtl8150 fix unintiatilzed variables in rtl8150_get_link_ksettings
+    - regulator: core: Fix modpost error "regulator_get_regmap" undefined
+    - dmaengine: idxd: Fix possible Use-After-Free in irq_process_work_list
+    - dmaengine: ioat: switch from 'pci_' to 'dma_' API
+    - dmaengine: ioat: Drop redundant pci_enable_pcie_error_reporting()
+    - dmaengine: ioatdma: Fix leaking on version mismatch
+    - dmaengine: ioat: use PCI core macros for PCIe Capability
+    - dmaengine: ioatdma: Fix error path in ioat3_dma_probe()
+    - dmaengine: ioatdma: Fix kmemleak in ioat_pci_probe()
+    - dmaengine: ioatdma: Fix missing kmem_cache_destroy()
+    - regulator: bd71815: fix ramp values
+    - ACPICA: Revert "ACPICA: avoid Info: mapping multiple BARs. Your kernel is
+      fine."
+    - RDMA/mlx5: Add check for srq max_sge attribute
+    - serial: stm32: rework RX over DMA
+    - net: do not leave a dangling sk pointer, when socket creation fails
+    - btrfs: retry block group reclaim without infinite loop
+    - KVM: x86: Always sync PIR to IRR prior to scanning I/O APIC routes
+    - ALSA: hda/realtek: Limit mic boost on N14AP7
+    - drm/i915/mso: using joiner is not possible with eDP MSO
+    - drm/radeon: fix UBSAN warning in kv_dpm.c
+    - gcov: add support for GCC 14
+    - kcov: don't lose track of remote references during softirqs
+    - tcp: clear tp->retrans_stamp in tcp_rcv_fastopen_synack()
+    - i2c: ocores: set IACK bit after core is enabled
+    - dt-bindings: i2c: google,cros-ec-i2c-tunnel: correct path to i2c-controller
+      schema
+    - arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
+    - drm/amd/display: revert Exit idle optimizations before HDCP execution
+    - perf: script: add raw|disasm arguments to --insn-trace option
+    - perf script: Show also errors for --insn-trace option
+    - ARM: dts: samsung: smdkv310: fix keypad no-autorepeat
+    - ARM: dts: samsung: exynos4412-origen: fix keypad no-autorepeat
+    - ARM: dts: samsung: smdk4412: fix keypad no-autorepeat
+    - rtlwifi: rtl8192de: Style clean-ups
+    - wifi: rtlwifi: rtl8192de: Fix 5 GHz TX power
+    - pmdomain: ti-sci: Fix duplicate PD referrals
+    - bcache: fix variable length array abuse in btree_iter
+    - tracing: Add MODULE_DESCRIPTION() to preemptirq_delay_test
+    - x86/cpu/vfm: Add new macros to work with (vendor/family/model) values
+    - x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
+    - ksmbd: ignore trailing slashes in share paths
+    - drm/i915/gt: Only kick the signal worker if there's been an update
+    - drm/i915/gt: Disarm breadcrumbs if engines are already idle
+    - Revert "kheaders: substituting --sort in archive creation"
+    - kheaders: explicitly define file modes for archived headers
+    - riscv: mm: init: try best to use IS_ENABLED(CONFIG_64BIT) instead of #ifdef
+    - riscv: fix overlap of allocated page and PTR_ERR
+    - perf/core: Fix missing wakeup when waiting for context reference
+    - PCI: Add PCI_ERROR_RESPONSE and related definitions
+    - x86/amd_nb: Check for invalid SMN reads
+    - smb: client: fix deadlock in smb2_find_smb_tcon()
+    - ACPI: x86: utils: Add Picasso to the list for forcing StorageD3Enable
+    - ACPI: x86: Force StorageD3Enable on more products
+    - gve: Add RX context.
+    - gve: Clear napi->skb before dev_kfree_skb_any()
+    - Input: ili210x - fix ili251x_read_touch_data() return value
+    - pinctrl: fix deadlock in create_pinctrl() when handling -EPROBE_DEFER
+    - pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins
+    - pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins
+    - pinctrl: rockchip: use dedicated pinctrl type for RK3328
+    - pinctrl: rockchip: fix pinmux reset in rockchip_pmx_set
+    - cifs: fix typo in module parameter enable_gcm_256
+    - drm/amdgpu: fix UBSAN warning in kv_dpm.c
+    - net: mdio: add helpers to extract clause 45 regad and devad fields
+    - net: stmmac: Assign configured channel value to EXTTS event
+    - ASoC: fsl-asoc-card: set priv->pdev before using it
+    - net: dsa: microchip: fix initial port flush problem
+    - ibmvnic: Free any outstanding tx skbs during scrq reset
+    - net: phy: micrel: add Microchip KSZ 9477 to the device table
+    - xdp: Remove WARN() from __xdp_reg_mem_model()
+    - tcp: Use BPF timeout setting for SYN ACK RTO
+    - Fix race for duplicate reqsk on identical SYN
+    - sparc: fix old compat_sys_select()
+    - sparc: fix compat recv/recvfrom syscalls
+    - parisc: use correct compat recv/recvfrom syscalls
+    - tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed TFO
+    - netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data
+      registers
+    - bpf: Take return from set_memory_ro() into account with bpf_prog_lock_ro()
+    - drm/panel: ilitek-ili9881c: Fix warning with GPIO controllers that sleep
+    - vduse: validate block features only with block devices
+    - vduse: Temporarily fail if control queue feature requested
+    - x86/fpu: Fix AMD X86_BUG_FXSAVE_LEAK fixup
+    - mtd: partitions: redboot: Added conversion of operands to a larger type
+    - bpf: Add a check for struct bpf_fib_lookup size
+    - RDMA/restrack: Fix potential invalid address access
+    - net/iucv: Avoid explicit cpumask var allocation on stack
+    - net/dpaa2: Avoid explicit cpumask var allocation on stack
+    - crypto: ecdh - explicitly zeroize private_key
+    - ALSA: emux: improve patch ioctl data validation
+    - media: dvbdev: Initialize sbuf
+    - soc: ti: wkup_m3_ipc: Send NULL dummy message instead of pointer message
+    - drm/radeon/radeon_display: Decrease the size of allocated memory
+    - nvme: fixup comment for nvme RDMA Provider Type
+    - drm/panel: simple: Add missing display timing flags for KOE TX26D202VM0BWA
+    - gpio: davinci: Validate the obtained number of IRQs
+    - gpiolib: cdev: Disallow reconfiguration without direction (uAPI v1)
+    - x86: stop playing stack games in profile_pc()
+    - parisc: use generic sys_fanotify_mark implementation
+    - ocfs2: fix DIO failure due to insufficient transaction credits
+    - mmc: sdhci-pci: Convert PCIBIOS_* return codes to errnos
+    - mmc: sdhci: Do not invert write-protect twice
+    - mmc: sdhci: Do not lock spinlock around mmc_gpio_get_ro()
+    - i2c: testunit: don't erase registers after STOP
+    - i2c: testunit: discard write requests while old command is running
+    - iio: adc: ad7266: Fix variable checking bug
+    - iio: accel: fxls8962af: select IIO_BUFFER & IIO_KFIFO_BUF
+    - iio: chemical: bme680: Fix pressure value output
+    - iio: chemical: bme680: Fix calibration data variable
+    - iio: chemical: bme680: Fix overflows in compensate() functions
+    - iio: chemical: bme680: Fix sensor data read operation
+    - net: usb: ax88179_178a: improve link status logs
+    - usb: gadget: printer: SS+ support
+    - usb: gadget: printer: fix races against disable
+    - usb: musb: da8xx: fix a resource leak in probe()
+    - usb: atm: cxacru: fix endpoint checking in cxacru_bind()
+    - usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to
+      avoid deadlock
+    - serial: 8250_omap: Implementation of Errata i2310
+    - tty: mcf: MCF54418 has 10 UARTS
+    - net: can: j1939: Initialize unused data in j1939_send_one()
+    - net: can: j1939: recover socket queue on CAN bus error during BAM
+      transmission
+    - net: can: j1939: enhanced error handling for tightly received RTS messages
+      in xtp_rx_rts_session_new
+    - cpu/hotplug: Fix dynstate assignment in __cpuhp_setup_state_cpuslocked()
+    - kbuild: Install dtb files as 0644 in Makefile.dtbinst
+    - sh: rework sync_file_range ABI
+    - csky, hexagon: fix broken sys_sync_file_range
+    - hexagon: fix fadvise64_64 calling conventions
+    - drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_ld_modes
+    - drm/amdgpu: avoid using null object of framebuffer
+    - drm/i915/gt: Fix potential UAF by revoke of fence registers
+    - drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_hd_modes
+    - batman-adv: Don't accept TT entries for out-of-spec VIDs
+    - ata: ahci: Clean up sysfs file on error
+    - ata: libata-core: Fix double free on error
+    - ftruncate: pass a signed offset
+    - syscalls: fix compat_sys_io_pgetevents_time64 usage
+    - syscalls: fix sys_fanotify_mark prototype
+    - pwm: stm32: Refuse too small period requests
+    - nfs: Leave pages in the pagecache if readpage failed
+    - drivers: fix typo in firmware/efi/memmap.c
+    - efi: Correct comment on efi_memmap_alloc
+    - efi: memmap: Move manipulation routines into x86 arch tree
+    - efi: xen: Set EFI_PARAVIRT for Xen dom0 boot on all architectures
+    - efi/x86: Free EFI memory map only when installing a new one.
+    - KVM: arm64: vgic-v4: Make the doorbell request robust w.r.t preemption
+    - ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
+    - arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
+    - arm64: dts: rockchip: Add sound-dai-cells for RK3368
+    - serial: 8250_omap: Fix Errata i2310 with RX FIFO level check
+    - tracing/net_sched: NULL pointer dereference in perf_trace_qdisc_reset()
+    - Linux 5.15.162
+  * Fix L2CAP/LE/CPU/BI-02-C bluetooth certification failure  (LP: #2072858) //
+    Jammy update: v5.15.162 upstream stable release (LP: #2073765)
+    - Bluetooth: L2CAP: Fix rejecting L2CAP_CONN_PARAM_UPDATE_REQ
+  * net/sched: Fix conntrack use-after-free (LP: #2073092)
+    - net/sched: Fix UAF when resolving a clash
+  * Jammy update: v5.15.161 upstream stable release (LP: #2072617)
+    - x86/tsc: Trust initial offset in architectural TSC-adjust MSRs
+    - tty: n_gsm: fix missing receive state reset after mode switch
+    - speakup: Fix sizeof() vs ARRAY_SIZE() bug
+    - serial: 8250_bcm7271: use default_mux_rate if possible
+    - Revert "r8169: don't try to disable interrupts if NAPI is, scheduled
+      already"
+    - r8169: Fix possible ring buffer corruption on fragmented Tx packets.
+    - ring-buffer: Fix a race between readers and resize checks
+    - tools/latency-collector: Fix -Wformat-security compile warns
+    - net: smc91x: Fix m68k kernel compilation for ColdFire CPU
+    - nilfs2: fix unexpected freezing of nilfs_segctor_sync()
+    - nilfs2: fix potential hang in nilfs_detach_log_writer()
+    - fs/ntfs3: Remove max link count info display during driver init
+    - fs/ntfs3: Taking DOS names into account during link counting
+    - fs/ntfs3: Fix case when index is reused during tree transformation
+    - fs/ntfs3: Break dir enumeration if directory contents error
+    - ALSA: core: Fix NULL module pointer assignment at card init
+    - wifi: cfg80211: fix the order of arguments for trace events of the tx_rx_evt
+      class
+    - dt-bindings: rockchip: grf: Add missing type to 'pcie-phy' node
+    - net: usb: qmi_wwan: add Telit FN920C04 compositions
+    - drm/amd/display: Set color_mgmt_changed to true on unsuspend
+    - selftests: sud_test: return correct emulated syscall value on RISC-V
+    - regulator: irq_helpers: duplicate IRQ name
+    - ASoC: rt5645: Fix the electric noise due to the CBJ contacts floating
+    - ASoC: dt-bindings: rt5645: add cbj sleeve gpio property
+    - regulator: vqmmc-ipq4019: fix module autoloading
+    - ASoC: rt715: add vendor clear control register
+    - ASoC: rt715-sdca: volume step modification
+    - softirq: Fix suspicious RCU usage in __do_softirq()
+    - ASoC: da7219-aad: fix usage of device_get_named_child_node()
+    - drm/amdkfd: Flush the process wq before creating a kfd_process
+    - x86/mm: Remove broken vsyscall emulation code from the page fault code
+    - nvme: find numa distance only if controller has valid numa id
+    - epoll: be better about file lifetimes
+    - openpromfs: finish conversion to the new mount API
+    - crypto: bcm - Fix pointer arithmetic
+    - mm/slub, kunit: Use inverted data to corrupt kmem cache
+    - firmware: raspberrypi: Use correct device for DMA mappings
+    - ecryptfs: Fix buffer size for tag 66 packet
+    - nilfs2: fix out-of-range warning
+    - parisc: add missing export of __cmpxchg_u8()
+    - crypto: ccp - drop platform ifdef checks
+    - crypto: x86/nh-avx2 - add missing vzeroupper
+    - crypto: x86/sha256-avx2 - add missing vzeroupper
+    - crypto: x86/sha512-avx2 - add missing vzeroupper
+    - s390/cio: fix tracepoint subchannel type field
+    - jffs2: prevent xattr node from overflowing the eraseblock
+    - soc: mediatek: cmdq: Fix typo of CMDQ_JUMP_RELATIVE
+    - null_blk: Fix missing mutex_destroy() at module removal
+    - md: fix resync softlockup when bitmap size is less than array size
+    - wifi: ath10k: poll service ready message before failing
+    - x86/boot: Ignore relocations in .notes sections in walk_relocs() too
+    - sched/fair: Add EAS checks before updating root_domain::overutilized
+    - qed: avoid truncating work queue length
+    - bpf: Pack struct bpf_fib_lookup
+    - scsi: ufs: qcom: Perform read back after writing reset bit
+    - scsi: ufs: qcom: Perform read back after writing REG_UFS_SYS1CLK_1US
+    - scsi: ufs: ufs-qcom: Fix the Qcom register name for offset 0xD0
+    - scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5
+    - scsi: ufs: qcom: Perform read back after writing unipro mode
+    - scsi: ufs: qcom: Perform read back after writing CGC enable
+    - scsi: ufs: cdns-pltfrm: Perform read back after writing HCLKDIV
+    - scsi: ufs: core: Perform read back after disabling interrupts
+    - scsi: ufs: core: Perform read back after disabling UIC_COMMAND_COMPL
+    - irqchip/alpine-msi: Fix off-by-one in allocation error path
+    - irqchip/loongson-pch-msi: Fix off-by-one on allocation error path
+    - ACPI: disable -Wstringop-truncation
+    - gfs2: Don't forget to complete delayed withdraw
+    - gfs2: Fix "ignore unlock failures after withdraw"
+    - selftests/bpf: Fix umount cgroup2 error in test_sockmap
+    - cpufreq: Reorganize checks in cpufreq_offline()
+    - cpufreq: Split cpufreq_offline()
+    - cpufreq: Rearrange locking in cpufreq_remove_dev()
+    - cpufreq: exit() callback is optional
+    - net: export inet_lookup_reuseport and inet6_lookup_reuseport
+    - net: remove duplicate reuseport_lookup functions
+    - udp: Avoid call to compute_score on multiple sites
+    - cppc_cpufreq: Fix possible null pointer dereference
+    - scsi: libsas: Fix the failure of adding phy with zero-address to port
+    - scsi: hpsa: Fix allocation size for Scsi_Host private data
+    - x86/purgatory: Switch to the position-independent small code model
+    - thermal/drivers/tsens: Fix null pointer dereference
+    - wifi: ath10k: Fix an error code problem in
+      ath10k_dbg_sta_write_peer_debug_trigger()
+    - wifi: ath10k: populate board data for WCN3990
+    - net: dsa: mv88e6xxx: Add support for model-specific pre- and post-reset
+      handlers
+    - net: dsa: mv88e6xxx: Avoid EEPROM timeout without EEPROM on 88E6250-family
+      switches
+    - tcp: avoid premature drops in tcp_add_backlog()
+    - pwm: sti: Convert to platform remove callback returning void
+    - pwm: sti: Prepare removing pwm_chip from driver data
+    - pwm: sti: Simplify probe function using devm functions
+    - net: give more chances to rcu in netdev_wait_allrefs_any()
+    - macintosh/via-macii: Fix "BUG: sleeping function called from invalid
+      context"
+    - wifi: carl9170: add a proper sanity check for endpoints
+    - wifi: ar5523: enable proper endpoint verification
+    - sh: kprobes: Merge arch_copy_kprobe() into arch_prepare_kprobe()
+    - Revert "sh: Handle calling csum_partial with misaligned data"
+    - selftests/binderfs: use the Makefile's rules, not Make's implicit rules
+    - selftests/resctrl: fix clang build failure: use LOCAL_HDRS
+    - HID: intel-ish-hid: ipc: Add check for pci_alloc_irq_vectors
+    - scsi: bfa: Ensure the copied buf is NUL terminated
+    - scsi: qedf: Ensure the copied buf is NUL terminated
+    - scsi: qla2xxx: Fix debugfs output for fw_resource_count
+    - wifi: mwl8k: initialize cmd->addr[] properly
+    - usb: aqc111: stop lying about skb->truesize
+    - net: usb: sr9700: stop lying about skb->truesize
+    - m68k: Fix spinlock race in kernel thread creation
+    - m68k: mac: Fix reboot hang on Mac IIci
+    - net: ipv6: fix wrong start position when receive hop-by-hop fragment
+    - eth: sungem: remove .ndo_poll_controller to avoid deadlocks
+    - net: ethernet: cortina: Locking fixes
+    - af_unix: Fix data races in unix_release_sock/unix_stream_sendmsg
+    - net: usb: smsc95xx: stop lying about skb->truesize
+    - net: openvswitch: fix overwriting ct original tuple for ICMPv6
+    - ipv6: sr: add missing seg6_local_exit
+    - ipv6: sr: fix incorrect unregister order
+    - ipv6: sr: fix invalid unregister error path
+    - net/mlx5: Discard command completions in internal error
+    - s390/bpf: Emit a barrier for BPF_FETCH instructions
+    - mptcp: SO_KEEPALIVE: fix getsockopt support
+    - printk: Let no_printk() use _printk()
+    - dev_printk: Add and use dev_no_printk()
+    - drm/amd/display: Fix potential index out of bounds in color transformation
+      function
+    - ASoC: Intel: Disable route checks for Skylake boards
+    - mtd: core: Report error if first mtd_otp_size() call fails in
+      mtd_otp_nvmem_add()
+    - mtd: rawnand: hynix: fixed typo
+    - fbdev: shmobile: fix snprintf truncation
+    - ASoC: kirkwood: Fix potential NULL dereference
+    - drm/meson: vclk: fix calculation of 59.94 fractional rates
+    - drm/mediatek: Add 0 size check to mtk_drm_gem_obj
+    - powerpc/fsl-soc: hide unused const variable
+    - fbdev: sisfb: hide unused variables
+    - media: ngene: Add dvb_ca_en50221_init return value check
+    - media: radio-shark2: Avoid led_names truncations
+    - drm: bridge: cdns-mhdp8546: Fix possible null pointer dereference
+    - media: ipu3-cio2: Use temporary storage for struct device pointer
+    - media: ipu3-cio2: Request IRQ earlier
+    - media: dt-bindings: ovti,ov2680: Fix the power supply names
+    - fbdev: sh7760fb: allow modular build
+    - media: atomisp: ssh_css: Fix a null-pointer dereference in
+      load_video_binaries
+    - drm/arm/malidp: fix a possible null pointer dereference
+    - drm: vc4: Fix possible null pointer dereference
+    - ASoC: tracing: Export SND_SOC_DAPM_DIR_OUT to its value
+    - drm/bridge: lt8912b: Don't log an error when DSI host can't be found
+    - drm/bridge: lt9611: Don't log an error when DSI host can't be found
+    - drm/bridge: tc358775: Don't log an error when DSI host can't be found
+    - drm/panel: simple: Add missing Innolux G121X1-L03 format, flags, connector
+    - drm/mipi-dsi: use correct return type for the DSC functions
+    - RDMA/mlx5: Adding remote atomic access flag to updatable flags
+    - RDMA/hns: Fix return value in hns_roce_map_mr_sg
+    - RDMA/hns: Fix deadlock on SRQ async events.
+    - RDMA/hns: Fix GMV table pagesize
+    - RDMA/hns: Use complete parentheses in macros
+    - RDMA/hns: Modify the print level of CQE error
+    - clk: qcom: mmcc-msm8998: fix venus clock issue
+    - x86/insn: Fix PUSH instruction in x86 instruction decoder opcode map
+    - ext4: avoid excessive credit estimate in ext4_tmpfile()
+    - virt: acrn: Prefer array_size and struct_size over open coded arithmetic
+    - virt: acrn: stop using follow_pfn
+    - drivers/virt/acrn: fix PFNMAP PTE checks in acrn_vm_ram_map()
+    - sunrpc: removed redundant procp check
+    - ext4: simplify calculation of blkoff in ext4_mb_new_blocks_simple
+    - ext4: fix unit mismatch in ext4_mb_new_blocks_simple
+    - ext4: try all groups in ext4_mb_new_blocks_simple
+    - ext4: remove unused parameter from ext4_mb_new_blocks_simple()
+    - ext4: fix potential unnitialized variable
+    - SUNRPC: Fix gss_free_in_token_pages()
+    - selftests/kcmp: Make the test output consistent and clear
+    - selftests/kcmp: remove unused open mode
+    - RDMA/IPoIB: Fix format truncation compilation errors
+    - selftests: net: bridge: increase IGMP/MLD exclude timeout membership
+      interval
+    - net: qrtr: ns: Fix module refcnt
+    - netrom: fix possible dead-lock in nr_rt_ioctl()
+    - af_packet: do not call packet_read_pending() from tpacket_destruct_skb()
+    - sched/fair: Allow disabling sched_balance_newidle with
+      sched_relax_domain_level
+    - sched/core: Fix incorrect initialization of the 'burst' parameter in
+      cpu_max_write()
+    - greybus: lights: check return of get_channel_from_mode
+    - f2fs: Delete f2fs_copy_page() and replace with memcpy_page()
+    - f2fs: fix to wait on page writeback in __clone_blkaddrs()
+    - soundwire: cadence: fix invalid PDI offset
+    - dmaengine: idma64: Add check for dma_set_max_seg_size
+    - firmware: dmi-id: add a release callback function
+    - serial: max3100: Lock port->lock when calling uart_handle_cts_change()
+    - serial: max3100: Update uart_driver_registered on driver removal
+    - serial: max3100: Fix bitwise types
+    - greybus: arche-ctrl: move device table to its right location
+    - PCI: tegra194: Fix probe path for Endpoint mode
+    - serial: sc16is7xx: add proper sched.h include for sched_set_fifo()
+    - dt-bindings: PCI: rcar-pci-host: Add optional regulators
+    - dt-bindings: PCI: rcar-pci-host: Add missing IOMMU properties
+    - f2fs: compress: fix to relocate check condition in
+      f2fs_{release,reserve}_compress_blocks()
+    - f2fs: convert to use sbi directly
+    - f2fs: compress: fix to relocate check condition in
+      f2fs_ioc_{,de}compress_file()
+    - f2fs: do not allow partial truncation on pinned file
+    - f2fs: fix typos in comments
+    - f2fs: fix to relocate check condition in f2fs_fallocate()
+    - f2fs: fix to check pinfile flag in f2fs_move_file_range()
+    - coresight: etm4x: Fix unbalanced pm_runtime_enable()
+    - iio: pressure: dps310: support negative temperature values
+    - coresight: etm4x: Do not hardcode IOMEM access for register restore
+    - coresight: etm4x: Do not save/restore Data trace control registers
+    - coresight: no-op refactor to make INSTP0 check more idiomatic
+    - coresight: etm4x: Cleanup TRCIDR0 register accesses
+    - coresight: etm4x: Safe access for TRCQCLTR
+    - coresight: etm4x: Fix access to resource selector registers
+    - fpga: region: Use standard dev_release for class driver
+    - fpga: region: add owner module and take its refcount
+    - microblaze: Remove gcc flag for non existing early_printk.c file
+    - microblaze: Remove early printk call from cpuinfo-static.c
+    - dt-bindings: pinctrl: mediatek: mt7622: fix array properties
+    - watchdog: bd9576_wdt: switch to using devm_fwnode_gpiod_get()
+    - watchdog: bd9576: Drop "always-running" property
+    - usb: gadget: u_audio: Clear uac pointer when freed.
+    - stm class: Fix a double free in stm_register_device()
+    - ppdev: Remove usage of the deprecated ida_simple_xx() API
+    - ppdev: Add an error check in register_device
+    - extcon: max8997: select IRQ_DOMAIN instead of depending on it
+    - PCI/EDR: Align EDR_PORT_DPC_ENABLE_DSM with PCI Firmware r3.3
+    - PCI/EDR: Align EDR_PORT_LOCATE_DSM with PCI Firmware r3.3
+    - f2fs: compress: fix to cover {reserve,release}_compress_blocks() w/ cp_rwsem
+      lock
+    - f2fs: fix to release node block count in error path of f2fs_new_node_page()
+    - f2fs: compress: don't allow unaligned truncation on released compress inode
+    - serial: sh-sci: protect invalidating RXDMA on shutdown
+    - libsubcmd: Fix parse-options memory leak
+    - s390/vdso: filter out mno-pic-data-is-text-relative cflag
+    - s390/vdso64: filter out munaligned-symbols flag for vdso
+    - s390/vdso: Generate unwind information for C modules
+    - s390/vdso: Use standard stack frame layout
+    - s390/ipl: Fix incorrect initialization of len fields in nvme reipl block
+    - s390/ipl: Fix incorrect initialization of nvme dump block
+    - s390/boot: Remove alt_stfle_fac_list from decompressor
+    - Input: ims-pcu - fix printf string overflow
+    - Input: ioc3kbd - convert to platform remove callback returning void
+    - Input: ioc3kbd - add device table
+    - mmc: sdhci_am654: Add tuning algorithm for delay chain
+    - mmc: sdhci_am654: Write ITAPDLY for DDR52 timing
+    - mmc: sdhci_am654: Drop lookup for deprecated ti,otap-del-sel
+    - mmc: sdhci_am654: Add OTAP/ITAP delay enable
+    - mmc: sdhci_am654: Add ITAPDLYSEL in sdhci_j721e_4bit_set_clock
+    - mmc: sdhci_am654: Fix ITAPDLY for HS400 timing
+    - Input: pm8xxx-vibrator - correct VIB_MAX_LEVELS calculation
+    - drm/msm/dsi: Print dual-DSI-adjusted pclk instead of original mode pclk
+    - drm/msm/dpu: Always flush the slave INTF on the CTL
+    - um: Fix return value in ubd_init()
+    - um: vector: fix bpfflash parameter evaluation
+    - fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
+    - fs/ntfs3: Use variable length array instead of fixed size
+    - drm/bridge: tc358775: fix support for jeida-18 and jeida-24
+    - media: stk1160: fix bounds checking in stk1160_copy_video()
+    - scsi: qla2xxx: Replace all non-returning strlcpy() with strscpy()
+    - Input: cyapa - add missing input core locking to suspend/resume functions
+    - media: flexcop-usb: clean up endpoint sanity checks
+    - media: flexcop-usb: fix sanity check of bNumEndpoints
+    - powerpc/pseries: Add failure related checks for h_get_mpp and h_get_ppp
+    - um: Fix the -Wmissing-prototypes warning for __switch_mm
+    - media: cec: cec-adap: always cancel work in cec_transmit_msg_fh
+    - media: cec: cec-api: add locking in cec_release()
+    - media: cec: call enable_adap on s_log_addrs
+    - media: cec: abort if the current transmit was canceled
+    - media: cec: correctly pass on reply results
+    - media: cec: use call_op and check for !unregistered
+    - media: cec-adap.c: drop activate_cnt, use state info instead
+    - media: cec: core: avoid recursive cec_claim_log_addrs
+    - media: cec: core: avoid confusing "transmit timed out" message
+    - null_blk: Fix the WARNING: modpost: missing MODULE_DESCRIPTION()
+    - ASoC: mediatek: mt8192: fix register configuration for tdm
+    - regulator: bd71828: Don't overwrite runtime voltages
+    - x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when
+      UNWINDER_FRAME_POINTER=y
+    - [Config] Update CONFIG_ARCH_WANT_FRAME_POINTERS
+    - net: Always descend into dsa/ folder with CONFIG_NET_DSA enabled
+    - ipv6: sr: fix missing sk_buff release in seg6_input_core
+    - nfc: nci: Fix uninit-value in nci_rx_work
+    - ASoC: tas2552: Add TX path for capturing AUDIO-OUT data
+    - NFSv4: Fixup smatch warning for ambiguous return
+    - sunrpc: fix NFSACL RPC retry on soft mount
+    - rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
+    - af_unix: Update unix_sk(sk)->oob_skb under sk_receive_queue lock.
+    - ipv6: sr: fix memleak in seg6_hmac_init_algo
+    - tcp: Fix shift-out-of-bounds in dctcp_update_alpha().
+    - openvswitch: Set the skbuff pkt_type for proper pmtud support.
+    - arm64: asm-bug: Add .align 2 to the end of __BUG_ENTRY
+    - virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
+    - riscv: stacktrace: Make walk_stackframe cross pt_regs frame
+    - riscv: stacktrace: fixed walk_stackframe()
+    - net: fec: avoid lock evasion when reading pps_enable
+    - tls: fix missing memory barrier in tls_init
+    - nfc: nci: Fix kcov check in nci_rx_work()
+    - nfc: nci: Fix handling of zero-length payload packets in nci_rx_work()
+    - ice: Interpret .set_channels() input differently
+    - netfilter: nfnetlink_queue: acquire rcu_read_lock() in
+      instance_destroy_rcu()
+    - netfilter: nft_payload: restore vlan q-in-q match support
+    - spi: Don't mark message DMA mapped when no transfer in it is
+    - dma-mapping: benchmark: fix node id validation
+    - dma-mapping: benchmark: handle NUMA_NO_NODE correctly
+    - nvmet: fix ns enable/disable possible hang
+    - net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061
+    - net/mlx5e: Fix IPsec tunnel mode offload feature check
+    - net/mlx5e: Use rx_missed_errors instead of rx_dropped for reporting buffer
+      exhaustion
+    - dma-buf/sw-sync: don't enable IRQ from sync_print_obj()
+    - bpf: Fix potential integer overflow in resolve_btfids
+    - enic: Validate length of nl attributes in enic_set_vf_port
+    - net: usb: smsc95xx: fix changing LED_SEL bit value updated from EEPROM
+    - bpf: Allow delete from sockmap/sockhash only if update is allowed
+    - net:fec: Add fec_enet_deinit()
+    - netfilter: nft_payload: move struct nft_payload_set definition where it
+      belongs
+    - netfilter: nft_payload: rebuild vlan header when needed
+    - netfilter: nft_payload: rebuild vlan header on h_proto access
+    - netfilter: nft_payload: skbuff vlan metadata mangle support
+    - netfilter: tproxy: bail out if IP has been disabled on the device
+    - kconfig: fix comparison to constant symbols, 'm', 'n'
+    - spi: stm32: Don't warn about spurious interrupts
+    - net: ena: Add capabilities field with support for ENI stats capability
+    - net: ena: Extract recurring driver reset code into a function
+    - net: ena: Do not waste napi skb cache
+    - net: ena: Add dynamic recycling mechanism for rx buffers
+    - net: ena: Reduce lines with longer column width boundary
+    - net: ena: Fix redundant device NUMA node override
+    - ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
+    - hwmon: (shtc1) Fix property misspelling
+    - ALSA: timer: Set lower bound of start tick time
+    - KVM: x86: Don't advertise guest.MAXPHYADDR as host.MAXPHYADDR in CPUID
+    - genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
+    - net: ena: Fix DMA syncing in XDP path when SWIOTLB is on
+    - media: cec: core: add adap_nb_transmit_canceled() callback
+    - SUNRPC: Fix loop termination condition in gss_free_in_token_pages()
+    - drm: Check output polling initialized before disabling
+    - drm: Check polling initialized before enabling in
+      drm_helper_probe_single_connector_modes
+    - mmc: core: Do not force a retune before RPMB switch
+    - io_uring: fail NOP if non-zero op flags is passed in
+    - afs: Don't cross .backup mountpoint from backup volume
+    - nilfs2: fix use-after-free of timer for log writer thread
+    - mptcp: fix full TCP keep-alive support
+    - vxlan: Fix regression when dropping packets due to invalid src addresses
+    - net: dsa: sja1105: always enable the INCL_SRCPT option
+    - net: dsa: tag_sja1105: always prefer source port information from INCL_SRCPT
+    - scripts/gdb: fix SB_* constants parsing
+    - sunrpc: exclude from freezer when waiting for requests:
+    - f2fs: fix to do sanity check on i_xattr_nid in sanity_check_inode()
+    - media: lgdt3306a: Add a check against null-pointer-def
+    - drm/amdgpu: add error handle to avoid out-of-bounds
+    - ata: pata_legacy: make legacy_exit() work again
+    - thermal/drivers/qcom/lmh: Check for SCM availability at probe
+    - soc: qcom: rpmh-rsc: Enhance check for VRM in-flight request
+    - ACPI: resource: Do IRQ override on TongFang GXxHRXx and GMxHGxx
+    - arm64: tegra: Correct Tegra132 I2C alias
+    - arm64: dts: qcom: qcs404: fix bluetooth device address
+    - md/raid5: fix deadlock that raid5d() wait for itself to clear
+      MD_SB_CHANGE_PENDING
+    - wifi: rtl8xxxu: Fix the TX power of RTL8192CU, RTL8723AU
+    - wifi: rtlwifi: rtl8192de: Fix low speed with WPA3-SAE
+    - wifi: rtlwifi: rtl8192de: Fix endianness issue in RX path
+    - arm64: dts: hi3798cv200: fix the size of GICR
+    - media: mc: mark the media devnode as registered from the, start
+    - media: mxl5xx: Move xpt structures off stack
+    - media: v4l2-core: hold videodev_lock until dev reg, finishes
+    - mmc: core: Add mmc_gpiod_set_cd_config() function
+    - mmc: sdhci-acpi: Sort DMI quirks alphabetically
+    - mmc: sdhci-acpi: Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
+    - mmc: sdhci-acpi: Disable write protect detection on Toshiba WT10-A
+    - fbdev: savage: Handle err return when savagefb_check_var failed
+    - drm/amdgpu/atomfirmware: add intergrated info v2.3 table
+    - KVM: arm64: Fix AArch32 register narrowing on userspace write
+    - KVM: arm64: Allow AArch32 PSTATE.M to be restored as System mode
+    - crypto: ecdsa - Fix module auto-load on add-key
+    - crypto: ecrdsa - Fix module auto-load on add_key
+    - crypto: qat - Fix ADF_DEV_RESET_SYNC memory leak
+    - net/ipv6: Fix route deleting failure when metric equals 0
+    - net/9p: fix uninit-value in p9_client_rpc()
+    - intel_th: pci: Add Meteor Lake-S CPU support
+    - sparc64: Fix number of online CPUs
+    - watchdog: rti_wdt: Set min_hw_heartbeat_ms to accommodate a safety margin
+    - kdb: Fix buffer overflow during tab-complete
+    - kdb: Use format-strings rather than '\0' injection in kdb_read()
+    - kdb: Fix console handling when editing and tab-completing commands
+    - kdb: Merge identical case statements in kdb_read()
+    - kdb: Use format-specifiers rather than memset() for padding in kdb_read()
+    - net: fix __dst_negative_advice() race
+    - sparc: move struct termio to asm/termios.h
+    - ext4: set type of ac_groups_linear_remaining to __u32 to avoid overflow
+    - ext4: fix mb_cache_entry's e_refcnt leak in ext4_xattr_block_cache_find()
+    - s390/ap: Fix crash in AP internal function modify_bitmap()
+    - s390/cpacf: Split and rework cpacf query functions
+    - s390/cpacf: Make use of invalid opcode produce a link error
+    - i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
+    - EDAC/igen6: Convert PCIBIOS_* return codes to errnos
+    - nfs: fix undefined behavior in nfs_block_bits()
+    - NFS: Fix READ_PLUS when server doesn't support OP_READ_PLUS
+    - scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW major version > 5
+    - Linux 5.15.161
+  * Virtualbox Guru meditation on VM start caused by kernel commit in v6.9-rc4
+    (LP: #2073267)
+    - SAUCE: Revert "randomize_kstack: Improve entropy diffusion"
+  * CVE-2024-26921
+    - inet: inet_defrag: prevent sk release while still in use
+  * Jammy update: v5.15.162 upstream stable release (LP: #2073765) //
+    CVE-2024-39484
+    - mmc: davinci: Don't strip remove function when driver is builtin
+  * CVE-2024-39292
+    - um: Add winch to winch_handlers before registering winch IRQ
+  * CVE-2024-36901
+    - ipv6: prevent NULL dereference in ip6_output()
+  * CVE-2024-26830
+    - i40e: Do not allow untrusted VF to remove administratively set MAC
+  * CVE-2024-26680
+    - net: atlantic: Fix DMA mapping for PTP hwts ring
+  * CVE-2023-52760
+    - gfs2: Fix slab-use-after-free in gfs2_qd_dealloc
+  * CVE-2023-52629
+    - sh: push-switch: Reorder cleanup operations to avoid use-after-free bug
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 21 Aug 2024 13:14:37 +1000
+
+linux-xilinx-zynqmp (5.15.0-1033.37) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1033.37 -proposed tracker (LP: #2072252)
+
+  * boot failure on kv260 (LP: #2072456)
+    - Revert "dmaengine: xilinx: dpdma: Fix race condition in vsync IRQ"
+
+  [ Ubuntu: 5.15.0-118.128 ]
+
+  * jammy/linux: 5.15.0-118.128 -proposed tracker (LP: #2072255)
+  * Jammy update: v5.15.160 upstream stable release (LP: #2070292)
+    - drm/amd/display: Fix division by zero in setup_dsc_config
+    - pinctrl: core: handle radix_tree_insert() errors in
+      pinctrl_register_one_pin()
+    - nfsd: don't allow nfsd threads to be signalled.
+    - KEYS: trusted: Fix memory leak in tpm2_key_encode()
+    - Revert "selftests: mm: fix map_hugetlb failure on 64K page size systems"
+    - net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access
+    - net: bcmgenet: synchronize UMAC_CMD access
+    - netlink: annotate lockless accesses to nlk->max_recvmsg_len
+    - netlink: annotate data-races around sk->sk_err
+    - KVM: x86: Clear "has_error_code", not "error_code", for RM exception
+      injection
+    - drm/amdgpu: Fix possible NULL dereference in
+      amdgpu_ras_query_error_status_helper()
+    - binder: fix max_thread type inconsistency
+    - usb: typec: ucsi: displayport: Fix potential deadlock
+    - serial: kgdboc: Fix NMI-safety problems from keyboard reset code
+    - remoteproc: mediatek: Make sure IPI buffer fits in L2TCM
+    - KEYS: trusted: Do not use WARN when encode fails
+    - admin-guide/hw-vuln/core-scheduling: fix return type of PR_SCHED_CORE_GET
+    - docs: kernel_include.py: Cope with docutils 0.21
+    - Linux 5.15.160
+  * Jammy update: v5.15.159 upstream stable release (LP: #2070028)
+    - dmaengine: pl330: issue_pending waits until WFP state
+    - dmaengine: Revert "dmaengine: pl330: issue_pending waits until WFP state"
+    - wifi: nl80211: don't free NULL coalescing rule
+    - ksmbd: fix slab-out-of-bounds in smb2_allocate_rsp_buf
+    - ksmbd: validate request buffer size in smb2_allocate_rsp_buf()
+    - ksmbd: clear RENAME_NOREPLACE before calling vfs_rename
+    - eeprom: at24: Use dev_err_probe for nvmem register failure
+    - eeprom: at24: Probe for DDR3 thermal sensor in the SPD case
+    - eeprom: at24: fix memory corruption race condition
+    - pinctrl: pinctrl-aspeed-g6: Fix register offset for pinconf of GPIOR-T
+    - pinctrl/meson: fix typo in PDM's pin name
+    - pinctrl: core: delete incorrect free in pinctrl_enable()
+    - pinctrl: mediatek: paris: Rework mtk_pinconf_{get,set} switch/case logic
+    - pinctrl: mediatek: paris: Fix PIN_CONFIG_INPUT_SCHMITT_ENABLE readback
+    - pinctrl: mediatek: paris: Rework support for
+      PIN_CONFIG_{INPUT,OUTPUT}_ENABLE
+    - sunrpc: add a struct rpc_stats arg to rpc_create_args
+    - nfs: expose /proc/net/sunrpc/nfs in net namespaces
+    - nfs: make the rpc_stat per net namespace
+    - nfs: Handle error of rpc_proc_register() in nfs_net_init().
+    - power: rt9455: hide unused rt9455_boost_voltage_values
+    - power: supply: mt6360_charger: Fix of_match for usb-otg-vbus regulator
+    - pinctrl: devicetree: fix refcount leak in pinctrl_dt_to_map()
+    - regulator: mt6360: De-capitalize devicetree regulator subnodes
+    - bpf, kconfig: Fix DEBUG_INFO_BTF_MODULES Kconfig definition
+    - bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue
+    - bpf: Fix a verifier verbose message
+    - spi: hisi-kunpeng: Delete the dump interface of data registers in debugfs
+    - s390/mm: Fix storage key clearing for guest huge pages
+    - s390/mm: Fix clearing storage keys for huge pages
+    - xdp: Move conversion to xdp_frame out of map functions
+    - xdp: Add xdp_do_redirect_frame() for pre-computed xdp_frames
+    - xdp: use flags field to disambiguate broadcast redirect
+    - bna: ensure the copied buf is NUL terminated
+    - octeontx2-af: avoid off-by-one read from userspace
+    - nsh: Restore skb->{protocol,data,mac_header} for outer header in
+      nsh_gso_segment().
+    - net l2tp: drop flow hash on forward
+    - s390/vdso: Add CFI for RA register to asm macro vdso_func
+    - net: qede: sanitize 'rc' in qede_add_tc_flower_fltr()
+    - net: qede: use return from qede_parse_flow_attr() for flower
+    - net: qede: use return from qede_parse_flow_attr() for flow_spec
+    - net: qede: use return from qede_parse_actions()
+    - ASoC: meson: axg-fifo: use FIELD helpers
+    - ASoC: meson: axg-fifo: use threaded irq to check periods
+    - ASoC: meson: axg-card: make links nonatomic
+    - ASoC: meson: axg-tdm-interface: manage formatters in trigger
+    - ASoC: meson: cards: select SND_DYNAMIC_MINORS
+    - ALSA: hda: intel-sdw-acpi: fix usage of device_get_named_child_node()
+    - s390/cio: Ensure the copied buf is NUL terminated
+    - cxgb4: Properly lock TX queue for the selftest.
+    - net: dsa: mv88e6xxx: Fix number of databases for 88E6141 / 88E6341
+    - net: bridge: fix multicast-to-unicast with fraglist GSO
+    - net: core: reject skb_copy(_expand) for fraglist GSO skbs
+    - tipc: fix a possible memleak in tipc_buf_append
+    - s390/qeth: don't keep track of Input Queue count
+    - s390/qeth: Fix kernel panic after setting hsuid
+    - drm/panel: ili9341: Respect deferred probe
+    - drm/panel: ili9341: Use predefined error codes
+    - net: gro: add flush check in udp_gro_receive_segment
+    - clk: sunxi-ng: h6: Reparent CPUX during PLL CPUX rate change
+    - KVM: arm64: vgic-v2: Use cpuid from userspace as vcpu_id
+    - KVM: arm64: vgic-v2: Check for non-NULL vCPU in vgic_v2_parse_attr()
+    - scsi: lpfc: Move NPIV's transport unregistration to after resource clean up
+    - scsi: lpfc: Update lpfc_ramp_down_queue_handler() logic
+    - scsi: lpfc: Replace hbalock with ndlp lock in lpfc_nvme_unregister_port()
+    - gfs2: Fix invalid metadata access in punch_hole
+    - wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc
+    - wifi: cfg80211: fix rdev_dump_mpp() arguments order
+    - net: mark racy access on sk->sk_rcvbuf
+    - scsi: bnx2fc: Remove spin_lock_bh while releasing resources after upload
+    - btrfs: return accurate error code on open failure in open_fs_devices()
+    - kbuild: Disable KCSAN for autogenerated *.mod.c intermediaries
+    - ALSA: line6: Zero-initialize message buffers
+    - net: bcmgenet: Reset RBUF on first open
+    - ata: sata_gemini: Check clk_enable() result
+    - firewire: ohci: mask bus reset interrupts between ISR and bottom half
+    - tools/power turbostat: Fix added raw MSR output
+    - tools/power turbostat: Fix Bzy_MHz documentation typo
+    - btrfs: make btrfs_clear_delalloc_extent() free delalloc reserve
+    - btrfs: always clear PERTRANS metadata during commit
+    - scsi: target: Fix SELinux error when systemd-modules loads the target module
+    - blk-iocost: avoid out of bounds shift
+    - gpu: host1x: Do not setup DMA for virtual devices
+    - MIPS: scall: Save thread_info.syscall unconditionally on entry
+    - selftests: timers: Fix valid-adjtimex signed left-shift undefined behavior
+    - iommu: mtk: fix module autoloading
+    - fs/9p: only translate RWX permissions for plain 9P2000
+    - fs/9p: translate O_TRUNC into OTRUNC
+    - 9p: explicitly deny setlease attempts
+    - gpio: wcove: Use -ENOTSUPP consistently
+    - gpio: crystalcove: Use -ENOTSUPP consistently
+    - clk: Don't hold prepare_lock when calling kref_put()
+    - fs/9p: drop inodes immediately on non-.L too
+    - drm/nouveau/dp: Don't probe eDP ports twice harder
+    - net:usb:qmi_wwan: support Rolling modules
+    - bpf, sockmap: TCP data stall on recv before accept
+    - bpf, sockmap: Handle fin correctly
+    - bpf, sockmap: Convert schedule_work into delayed_work
+    - bpf, sockmap: Reschedule is now done through backlog
+    - bpf, sockmap: Improved check for empty queue
+    - qibfs: fix dentry leak
+    - xfrm: Preserve vlan tags for transport mode software GRO
+    - ARM: 9381/1: kasan: clear stale stack poison
+    - tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets
+    - tcp: Use refcount_inc_not_zero() in tcp_twsk_unique().
+    - Bluetooth: Fix use-after-free bugs caused by sco_sock_timeout
+    - Bluetooth: l2cap: fix null-ptr-deref in l2cap_chan_timeout
+    - rtnetlink: Correct nested IFLA_VF_VLAN_LIST attribute validation
+    - hwmon: (corsair-cpro) Use a separate buffer for sending commands
+    - hwmon: (corsair-cpro) Use complete_all() instead of complete() in
+      ccp_raw_event()
+    - hwmon: (corsair-cpro) Protect ccp->wait_input_report with a spinlock
+    - phonet: fix rtm_phonet_notify() skb allocation
+    - net: bridge: fix corrupted ethernet header on multicast-to-unicast
+    - ipv6: fib6_rules: avoid possible NULL dereference in fib6_rule_action()
+    - net: hns3: PF support get unicast MAC address space assigned by firmware
+    - net: hns3: using user configure after hardware reset
+    - net: hns3: add log for workqueue scheduled late
+    - net: hns3: add query vf ring and vector map relation
+    - net: hns3: refactor function hclge_mbx_handler()
+    - net: hns3: direct return when receive a unknown mailbox message
+    - net: hns3: refactor hns3 makefile to support hns3_common module
+    - net: hns3: create new cmdq hardware description structure hclge_comm_hw
+    - net: hns3: create new set of unified hclge_comm_cmd_send APIs
+    - net: hns3: refactor hclge_cmd_send with new hclge_comm_cmd_send API
+    - net: hns3: change type of numa_node_mask as nodemask_t
+    - net: hns3: use appropriate barrier function after setting a bit value
+    - net: hns3: split function hclge_init_vlan_config()
+    - net: hns3: fix port vlan filter not disabled issue
+    - drm/meson: dw-hdmi: power up phy on device init
+    - drm/meson: dw-hdmi: add bandgap setting for g12
+    - drm/connector: Add \n to message about demoting connector force-probes
+    - drm/amd/display: Atom Integrated System Info v2_2 for DCN35
+    - Revert "Revert "ACPI: CPPC: Use access_width over bit_width for system
+      memory accesses""
+    - ACPI: CPPC: Fix bit_offset shift in MASK_VAL() macro
+    - ACPI: CPPC: Fix access width used for PCC registers
+    - btrfs: fix kvcalloc() arguments order in btrfs_ioctl_send()
+    - firewire: nosy: ensure user_length is taken into account when fetching
+      packet contents
+    - Reapply "drm/qxl: simplify qxl_fence_wait"
+    - arm64: dts: qcom: Fix 'interrupt-map' parent address cells
+    - usb: typec: ucsi: Check for notifications after init
+    - usb: typec: ucsi: Fix connector check on init
+    - usb: Fix regression caused by invalid ep0 maxpacket in virtual SuperSpeed
+      device
+    - usb: ohci: Prevent missed ohci interrupts
+    - usb: gadget: composite: fix OS descriptors w_value logic
+    - usb: gadget: f_fs: Fix a race condition when processing setup packets.
+    - usb: xhci-plat: Don't include xhci.h
+    - usb: dwc3: core: Prevent phy suspend during init
+    - ALSA: hda/realtek: Fix mute led of HP Laptop 15-da3001TU
+    - btrfs: add missing mutex_unlock in btrfs_relocate_sys_chunks()
+    - mptcp: ensure snd_nxt is properly initialized on connect
+    - dt-bindings: iio: health: maxim,max30102: fix compatible check
+    - iio:imu: adis16475: Fix sync mode setting
+    - iio: accel: mxc4005: Interrupt handling fixes
+    - tipc: fix UAF in error path
+    - net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()
+    - ASoC: tegra: Fix DSPK 16-bit playback
+    - ASoC: ti: davinci-mcasp: Fix race condition during probe
+    - dyndbg: fix old BUG_ON in >control parser
+    - slimbus: qcom-ngd-ctrl: Add timeout for wait operation
+    - mei: me: add lunar lake point M DID
+    - drm/vmwgfx: Fix invalid reads in fence signaled events
+    - net: fix out-of-bounds access in ops_init
+    - hwmon: (pmbus/ucd9000) Increase delay from 250 to 500us
+    - regulator: core: fix debugfs creation regression
+    - Bluetooth: qca: add missing firmware sanity checks
+    - Bluetooth: qca: fix NVM configuration parsing
+    - Bluetooth: qca: fix firmware check error path
+    - keys: Fix overwrite of key expiration on instantiation
+    - md: fix kmemleak of rdev->serial
+    - Linux 5.15.159
+  * Freezing user space processes failed after 20.008 seconds (1 tasks refusing
+    to freeze, wq_busy=0) (LP: #2061091)
+    - ALSA: Fix deadlocks with kctl removals at disconnection
+  * CVE-2024-27017
+    - netfilter: nft_set_pipapo: constify lookup fn args where possible
+    - netfilter: nft_set_pipapo: walk over current view on netlink dump
+    - netfilter: nf_tables: missing iterator type in lookup walk
+  * CVE-2024-26952
+    - ksmbd: fix potencial out-of-bounds when buffer offset is invalid
+  * CVE-2024-26886
+    - Bluetooth: af_bluetooth: Fix deadlock
+  * CVE-2023-52752
+    - smb: client: fix use-after-free bug in cifs_debug_data_proc_show()
+  * CVE-2024-25742
+    - x86/sev: Harden #VC instruction emulation somewhat
+    - x86/sev: Check for MWAITX and MONITORX opcodes in the #VC handler
+  * CVE-2024-36016
+    - tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
+
+  [ Ubuntu: 5.15.0-116.126 ]
+
+  * jammy/linux: 5.15.0-116.126 -proposed tracker (LP: #2071603)
+  * idxd: NULL pointer dereference reading wq op_config attribute (LP: #2069081)
+    - SAUCE: dmaengine: idxd: set is_visible member of idxd_wq_attribute_group
+  * AMD GPUs fail with null pointer dereference when IOMMU enabled, leading to
+    black screen (LP: #2068738)
+    - SAUCE: Revert "drm/amdgpu: init iommu after amdkfd device init"
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 18 Jul 2024 09:24:53 -0400
+
+linux-xilinx-zynqmp (5.15.0-1032.36) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1032.36 -proposed tracker (LP: #2068392)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.zynqmp/dkms-versions -- update from kernel-versions
+      (main/2024.06.10)
+
+  [ Ubuntu: 5.15.0-115.125 ]
+
+  * jammy/linux: 5.15.0-115.125 -proposed tracker (LP: #2068396)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] debian.master/dkms-versions -- update from kernel-versions
+      (main/2024.06.10)
+  * Jammy update: v5.15.158 upstream stable release (LP: #2067974)
+    - smb: client: fix rename(2) regression against samba
+    - cifs: reinstate original behavior again for forceuid/forcegid
+    - HID: intel-ish-hid: ipc: Fix dev_err usage with uninitialized dev->devc
+    - HID: logitech-dj: allow mice to use all types of reports
+    - arm64: dts: rockchip: enable internal pull-up on Q7_USB_ID for RK3399 Puma
+    - arm64: dts: rockchip: fix alphabetical ordering RK3399 puma
+    - arm64: dts: rockchip: enable internal pull-up on PCIE_WAKE# for RK3399 Puma
+    - arm64: dts: rockchip: Remove unsupported node from the Pinebook Pro dts
+    - arm64: dts: mediatek: mt8183: Add power-domains properity to mfgcfg
+    - arm64: dts: mediatek: mt7622: add support for coherent DMA
+    - arm64: dts: mediatek: mt7622: introduce nodes for Wireless Ethernet Dispatch
+    - arm64: dts: mediatek: mt7622: fix clock controllers
+    - arm64: dts: mediatek: mt7622: fix IR nodename
+    - arm64: dts: mediatek: mt7622: fix ethernet controller "compatible"
+    - arm64: dts: mediatek: mt7622: drop "reset-names" from thermal block
+    - arm64: dts: mediatek: mt2712: fix validation errors
+    - ARC: [plat-hsdk]: Remove misplaced interrupt-cells property
+    - wifi: iwlwifi: mvm: remove old PASN station when adding a new one
+    - wifi: iwlwifi: mvm: return uid from iwl_mvm_build_scan_cmd
+    - vxlan: drop packets from invalid src-address
+    - mlxsw: core: Unregister EMAD trap using FORWARD action
+    - icmp: prevent possible NULL dereferences from icmp_build_probe()
+    - bridge/br_netlink.c: no need to return void function
+    - NFC: trf7970a: disable all regulators on removal
+    - ipv4: check for NULL idev in ip_route_use_hint()
+    - net: usb: ax88179_178a: stop lying about skb->truesize
+    - net: gtp: Fix Use-After-Free in gtp_dellink
+    - ipvs: Fix checksumming on GSO of SCTP packets
+    - net: openvswitch: Fix Use-After-Free in ovs_ct_exit
+    - mlxsw: spectrum_acl_tcam: Fix race during rehash delayed work
+    - mlxsw: spectrum_acl_tcam: Fix possible use-after-free during activity update
+    - mlxsw: spectrum_acl_tcam: Fix possible use-after-free during rehash
+    - mlxsw: spectrum_acl_tcam: Rate limit error message
+    - mlxsw: spectrum_acl_tcam: Fix memory leak during rehash
+    - mlxsw: spectrum_acl_tcam: Fix warning during rehash
+    - mlxsw: spectrum_acl_tcam: Fix incorrect list API usage
+    - mlxsw: spectrum_acl_tcam: Fix memory leak when canceling rehash work
+    - netfilter: nf_tables: honor table dormant flag from netdev release event
+      path
+    - i40e: Do not use WQ_MEM_RECLAIM flag for workqueue
+    - i40e: Report MFS in decimal base instead of hex
+    - iavf: Fix TC config comparison with existing adapter TC config
+    - net: ethernet: ti: am65-cpts: Fix PTPv1 message type on TX packets
+    - af_unix: Suppress false-positive lockdep splat for spin_lock() in
+      __unix_gc().
+    - serial: core: Provide port lock wrappers
+    - serial: mxs-auart: add spinlock around changing cts state
+    - drm-print: add drm_dbg_driver to improve namespace symmetry
+    - drm/vmwgfx: Fix crtc's atomic check conditional
+    - Revert "crypto: api - Disallow identical driver names"
+    - net/mlx5e: Fix a race in command alloc flow
+    - tracing: Show size of requested perf buffer
+    - tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker
+      together
+    - x86/cpu: Fix check for RDPKRU in __show_regs()
+    - Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old()
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0bda:0x4853
+    - Bluetooth: qca: fix NULL-deref on non-serdev suspend
+    - mmc: sdhci-msm: pervent access to suspended controller
+    - btrfs: fix information leak in btrfs_ioctl_logical_to_ino()
+    - cpu: Re-enable CPU mitigations by default for !X86 architectures
+    - [Configs] Update CPU mitigation configs
+    - arm64: dts: rockchip: enable internal pull-up for Q7_THRM# on RK3399 Puma
+    - drm/amdgpu/sdma5.2: use legacy HDP flush for SDMA2/3
+    - drm/amdgpu: Fix leak when GPU memory allocation fails
+    - irqchip/gic-v3-its: Prevent double free on error
+    - ethernet: Add helper for assigning packet type when dest address does not
+      match device address
+    - net: b44: set pause params only when interface is up
+    - stackdepot: respect __GFP_NOLOCKDEP allocation flag
+    - mtd: diskonchip: work around ubsan link failure
+    - tcp: Clean up kernel listener's reqsk in inet_twsk_purge()
+    - tcp: Fix NEW_SYN_RECV handling in inet_twsk_purge()
+    - dmaengine: owl: fix register access functions
+    - idma64: Don't try to serve interrupts when device is powered off
+    - dma: xilinx_dpdma: Fix locking
+    - dmaengine: idxd: Fix oops during rmmod on single-CPU platforms
+    - riscv: fix VMALLOC_START definition
+    - riscv: Fix TASK_SIZE on 64-bit NOMMU
+    - i2c: smbus: fix NULL function pointer dereference
+    - fbdev: fix incorrect address computation in deferred IO
+    - HID: i2c-hid: remove I2C_HID_READ_PENDING flag to prevent lock-up
+    - bounds: Use the right number of bits for power-of-two CONFIG_NR_CPUS
+    - udp: preserve the connected status if only UDP cmsg
+    - serial: core: fix kernel-doc for uart_port_unlock_irqrestore()
+    - Linux 5.15.158
+  * Jammy update: v5.15.157 upstream stable release (LP: #2067959)
+    - ksmbd: don't send oplock break if rename fails
+    - ksmbd: validate payload size in ipc response
+    - ksmbd: do not set SMB2_GLOBAL_CAP_ENCRYPTION for SMB 3.1.1
+    - btrfs: record delayed inode root in transaction
+    - SUNRPC: Fix rpcgss_context trace event acceptor field
+    - selftests/ftrace: Limit length in subsystem-enable tests
+    - bpf: Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support
+    - bpf: Generalize check_ctx_reg for reuse with other types
+    - bpf: Generally fix helper register offset check
+    - bpf: Fix out of bounds access for ringbuf helpers
+    - bpf: Fix ringbuf memory type confusion when passing to helpers
+    - kprobes: Fix possible use-after-free issue on kprobe registration
+    - Revert "tracing/trigger: Fix to return error if failed to alloc snapshot"
+    - netfilter: nf_tables: Fix potential data-race in __nft_expr_type_get()
+    - netfilter: nf_tables: Fix potential data-race in __nft_obj_type_get()
+    - netfilter: br_netfilter: skip conntrack input hook for promisc packets
+    - netfilter: nf_flow_table: count pending offload workqueue tasks
+    - [Config] update configs to enable new NF_FLOW_TABLE_PROCFS
+    - netfilter: flowtable: validate pppoe header
+    - netfilter: flowtable: incorrect pppoe tuple
+    - af_unix: Call manage_oob() for every skb in unix_stream_read_generic().
+    - af_unix: Don't peek OOB data without MSG_OOB.
+    - tun: limit printing rate when illegal packet received by tun dev
+    - net: dsa: mt7530: fix mirroring frames received on local port
+    - net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
+    - RDMA/rxe: Fix the problem "mutex_destroy missing"
+    - RDMA/cm: Print the old state when cm_destroy_id gets timeout
+    - RDMA/mlx5: Fix port number for counter query in multi-port configuration
+    - s390/qdio: handle deferred cc1
+    - s390/cio: fix race condition during online processing
+    - drm: nv04: Fix out of bounds access
+    - drm/panel: visionox-rm69299: don't unregister DSI device
+    - clk: Remove prepare_lock hold assertion in __clk_release()
+    - clk: Mark 'all_lists' as const
+    - clk: remove extra empty line
+    - clk: Print an info line before disabling unused clocks
+    - clk: Initialize struct clk_core kref earlier
+    - clk: Get runtime PM before walking tree during disable_unused
+    - x86/bugs: Fix BHI retpoline check
+    - x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
+    - thunderbolt: Avoid notify PM core about runtime PM resume
+    - thunderbolt: Fix wake configurations after device unplug
+    - comedi: vmk80xx: fix incomplete endpoint checking
+    - serial/pmac_zilog: Remove flawed mitigation for rx irq flood
+    - USB: serial: option: add Fibocom FM135-GL variants
+    - USB: serial: option: add support for Fibocom FM650/FG650
+    - USB: serial: option: add Lonsung U8300/U9300 product
+    - USB: serial: option: support Quectel EM060K sub-models
+    - USB: serial: option: add Rolling RW101-GL and RW135-GL support
+    - USB: serial: option: add Telit FN920C04 rmnet compositions
+    - usb: dwc2: host: Fix dereference issue in DDMA completion flow.
+    - usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport
+      error
+    - mei: me: disable RPL-S on SPS and IGN firmwares
+    - speakup: Avoid crash on very long word
+    - fs: sysfs: Fix reference leak in sysfs_break_active_protection()
+    - KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
+    - KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
+    - arm64: hibernate: Fix level3 translation fault in swsusp_save()
+    - init/main.c: Fix potential static_command_line memory overflow
+    - drm/vmwgfx: Sort primary plane formats by order of preference
+    - nouveau: fix instmem race condition around ptr stores
+    - nilfs2: fix OOB in nilfs_set_de_type
+    - net: dsa: mt7530: set all CPU ports in MT7531_CPU_PMAP
+    - net: dsa: introduce preferred_default_local_cpu_port and use on MT7530
+    - net: dsa: mt7530: fix improper frames on all 25MHz and 40MHz XTAL MT7530
+    - net: dsa: mt7530: fix enabling EEE on MT7531 switch on all boards
+    - Linux 5.15.157
+  * [SRU][22.04.4]: megaraid_sas: Critical Bug Fixes (LP: #2046722)
+    - scsi: megaraid_sas: Log message when controller reset is requested but not
+      issued
+    - scsi: megaraid_sas: Driver version update to 07.727.03.00-rc1
+  * Jammy update: v5.15.156 upstream stable release (LP: #2065857)
+    - batman-adv: Avoid infinite loop trying to resize local TT
+    - ring-buffer: Only update pages_touched when a new page is touched
+    - Bluetooth: Fix memory leak in hci_req_sync_complete()
+    - media: cec: core: remove length check of Timer Status
+    - arm64: dts: imx8-ss-conn: fix usdhc wrong lpcg clock order
+    - Revert "drm/qxl: simplify qxl_fence_wait"
+    - nouveau: fix function cast warning
+    - scsi: qla2xxx: Fix off by one in qla_edif_app_getstats()
+    - net: openvswitch: fix unwanted error log on timeout policy probing
+    - u64_stats: Disable preemption on 32bit UP+SMP PREEMPT_RT during updates.
+    - xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING
+    - geneve: fix header validation in geneve[6]_xmit_skb
+    - af_unix: Clear stale u->oob_skb.
+    - octeontx2-af: Fix NIX SQ mode and BP config
+    - ipv6: fib: hide unused 'pn' variable
+    - ipv4/route: avoid unused-but-set-variable warning
+    - ipv6: fix race condition between ipv6_get_ifaddr and ipv6_del_addr
+    - netfilter: complete validation of user input
+    - net/mlx5: Properly link new fs rules into the tree
+    - net: sparx5: fix wrong config being used when reconfiguring PCS
+    - net: dsa: mt7530: trap link-local frames regardless of ST Port State
+    - af_unix: Do not use atomic ops for unix_sk(sk)->inflight.
+    - af_unix: Fix garbage collector racing against connect()
+    - net: ena: Fix potential sign extension issue
+    - net: ena: Wrong missing IO completions check order
+    - net: ena: Fix incorrect descriptor free behavior
+    - tracing: hide unused ftrace_event_id_fops
+    - iommu/vt-d: Allocate local memory for page request queue
+    - btrfs: qgroup: correctly model root qgroup rsv in convert
+    - drm/client: Fully protect modes[] with dev->mode_config.mutex
+    - vhost: Add smp_rmb() in vhost_vq_avail_empty()
+    - perf/x86: Fix out of range data
+    - x86/cpu: Actually turn off mitigations by default for
+      SPECULATION_MITIGATIONS=n
+    - selftests: timers: Fix abs() warning in posix_timers test
+    - x86/apic: Force native_apic_mem_read() to use the MOV instruction
+    - irqflags: Explicitly ignore lockdep_hrtimer_exit() argument
+    - x86/bugs: Fix return type of spectre_bhi_state()
+    - x86/bugs: Fix BHI documentation
+    - x86/bugs: Cache the value of MSR_IA32_ARCH_CAPABILITIES
+    - x86/bugs: Rename various 'ia32_cap' variables to 'x86_arch_cap_msr'
+    - x86/bugs: Fix BHI handling of RRSBA
+    - x86/bugs: Clarify that syscall hardening isn't a BHI mitigation
+    - x86/bugs: Remove CONFIG_BHI_MITIGATION_AUTO and spectre_bhi=auto
+    - [Config] updateconfigs to remove obsolete SPECTRE_BHI_AUTO
+    - x86/bugs: Replace CONFIG_SPECTRE_BHI_{ON,OFF} with
+      CONFIG_MITIGATION_SPECTRE_BHI
+    - [Config] updateconfigs to enable new MITIGATION_SPECTRE_BHI
+    - drm/i915/cdclk: Fix CDCLK programming order when pipes are active
+    - Linux 5.15.156
+  * Jammy update: v5.15.155 upstream stable release (LP: #2065805)
+    - amdkfd: use calloc instead of kzalloc to avoid integer overflow
+    - net: dsa: fix panic when DSA master device unbinds on shutdown
+    - wifi: ath9k: fix LNA selection in ath_ant_try_scan()
+    - VMCI: Fix memcpy() run-time warning in dg_dispatch_as_host()
+    - panic: Flush kernel log buffer at the end
+    - cpuidle: Avoid potential overflow in integer multiplication
+    - arm64: dts: rockchip: fix rk3328 hdmi ports node
+    - arm64: dts: rockchip: fix rk3399 hdmi ports node
+    - ionic: set adminq irq affinity
+    - pstore/zone: Add a null pointer check to the psz_kmsg_read
+    - tools/power x86_energy_perf_policy: Fix file leak in get_pkg_num()
+    - net: pcs: xpcs: Return EINVAL in the internal methods
+    - wifi: ath11k: decrease MHI channel buffer length to 8KB
+    - btrfs: handle chunk tree lookup error in btrfs_relocate_sys_chunks()
+    - btrfs: export: handle invalid inode or root reference in btrfs_get_parent()
+    - btrfs: send: handle path ref underflow in header iterate_inode_ref()
+    - net/smc: reduce rtnl pressure in smc_pnet_create_pnetids_list()
+    - Bluetooth: btintel: Fix null ptr deref in btintel_read_version
+    - Input: synaptics-rmi4 - fail probing if memory allocation for "phys" fails
+    - pinctrl: renesas: checker: Limit cfg reg enum checks to provided IDs
+    - sysv: don't call sb_bread() with pointers_lock held
+    - scsi: lpfc: Fix possible memory leak in lpfc_rcv_padisc()
+    - isofs: handle CDs with bad root inode but good Joliet root directory
+    - media: sta2x11: fix irq handler cast
+    - ALSA: firewire-lib: handle quirk to calculate payload quadlets as data block
+      counter
+    - ext4: add a hint for block bitmap corrupt state in mb_groups
+    - ext4: forbid commit inconsistent quota data when errors=remount-ro
+    - drm/amd/display: Fix nanosec stat overflow
+    - SUNRPC: increase size of rpc_wait_queue.qlen from unsigned short to unsigned
+      int
+    - Revert "ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default"
+    - libperf evlist: Avoid out-of-bounds access
+    - block: prevent division by zero in blk_rq_stat_sum()
+    - RDMA/cm: add timeout to cm_destroy_id wait
+    - Input: allocate keycode for Display refresh rate toggle
+    - platform/x86: touchscreen_dmi: Add an extra entry for a variant of the Chuwi
+      Vi8 tablet
+    - ktest: force $buildonly = 1 for 'make_warnings_file' test type
+    - ring-buffer: use READ_ONCE() to read cpu_buffer->commit_page in concurrent
+      environment
+    - tools: iio: replace seekdir() in iio_generic_buffer
+    - usb: typec: tcpci: add generic tcpci fallback compatible
+    - usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
+    - ASoC: soc-core.c: Skip dummy codec when adding platforms
+    - fbdev: viafb: fix typo in hw_bitblt_1 and hw_bitblt_2
+    - drivers/nvme: Add quirks for device 126f:2262
+    - fbmon: prevent division by zero in fb_videomode_from_videomode()
+    - netfilter: nf_tables: release batch on table validation from abort path
+    - netfilter: nf_tables: release mutex after nft_gc_seq_end from abort path
+    - netfilter: nf_tables: discard table flag update with pending basechain
+      deletion
+    - tty: n_gsm: require CAP_NET_ADMIN to attach N_GSM0710 ldisc
+    - gcc-plugins/stackleak: Ignore .noinstr.text and .entry.text
+    - gcc-plugins/stackleak: Avoid .head.text section
+    - virtio: reenable config if freezing device failed
+    - x86/mm/pat: fix VM_PAT handling in COW mappings
+    - randomize_kstack: Improve entropy diffusion
+    - platform/x86: intel-vbtn: Update tablet mode switch at end of probe
+    - Bluetooth: btintel: Fixe build regression
+    - VMCI: Fix possible memcpy() run-time warning in
+      vmci_datagram_invoke_guest_handler()
+    - Linux 5.15.155
+  * Jammy update: v5.15.154 upstream stable release (LP: #2065435)
+    - Documentation/hw-vuln: Update spectre doc
+    - x86/cpu: Support AMD Automatic IBRS
+    - media: staging: ipu3-imgu: Set fields before media_entity_pads_init()
+    - clk: qcom: gcc-sdm845: Add soft dependency on rpmhpd
+    - smack: Set SMACK64TRANSMUTE only for dirs in smack_inode_setxattr()
+    - smack: Handle SMACK64TRANSMUTE in smack_inode_setsecurity()
+    - arm: dts: marvell: Fix maxium->maxim typo in brownstone dts
+    - drm/vmwgfx: Fix possible null pointer derefence with invalid contexts
+    - pci_iounmap(): Fix MMIO mapping leak
+    - KVM: Always flush async #PF workqueue when vCPU is being destroyed
+    - sparc64: NMI watchdog: fix return value of __setup handler
+    - sparc: vDSO: fix return value of __setup handler
+    - crypto: qat - fix double free during reset
+    - crypto: qat - resolve race condition during AER recovery
+    - selftests/mqueue: Set timeout to 180 seconds
+    - ext4: correct best extent lstart adjustment logic
+    - block: Clear zone limits for a non-zoned stacked queue
+    - kasan: test: add memcpy test that avoids out-of-bounds write
+    - kasan/test: avoid gcc warning for intentional overflow
+    - bounds: support non-power-of-two CONFIG_NR_CPUS
+    - fat: fix uninitialized field in nostale filehandles
+    - ubifs: Set page uptodate in the correct place
+    - ubi: Check for too small LEB size in VTBL code
+    - ubi: correct the calculation of fastmap size
+    - mtd: rawnand: meson: fix scrambling mode value in command macro
+    - parisc: Avoid clobbering the C/B bits in the PSW with tophys and tovirt
+      macros
+    - parisc: Fix ip_fast_csum
+    - parisc: Fix csum_ipv6_magic on 32-bit systems
+    - parisc: Fix csum_ipv6_magic on 64-bit systems
+    - parisc: Strip upper 32 bit of sum in csum_ipv6_magic for 64-bit builds
+    - PM: suspend: Set mem_sleep_current during kernel command line setup
+    - clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
+    - clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
+    - clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
+    - clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
+    - usb: xhci: Add error handling in xhci_map_urb_for_dma
+    - powerpc/fsl: Fix mfpmr build errors with newer binutils
+    - USB: serial: ftdi_sio: add support for GMC Z216C Adapter IR-USB
+    - USB: serial: add device ID for VeriFone adapter
+    - USB: serial: cp210x: add ID for MGP Instruments PDS100
+    - USB: serial: option: add MeiG Smart SLM320 product
+    - USB: serial: cp210x: add pid/vid for TDK NC0110013M and MM0110113M
+    - PM: sleep: wakeirq: fix wake irq warning in system suspend
+    - mmc: tmio: avoid concurrent runs of mmc_request_done()
+    - fuse: fix root lookup with nonzero generation
+    - fuse: don't unhash root
+    - usb: typec: ucsi: Clean up UCSI_CABLE_PROP macros
+    - printk/console: Split out code that enables default console
+    - serial: Lock console when calling into driver before registration
+    - btrfs: fix off-by-one chunk length calculation at contains_pending_extent()
+    - PCI: Drop pci_device_remove() test of pci_dev->driver
+    - PCI/PM: Drain runtime-idle callbacks before driver removal
+    - PCI: Work around Intel I210 ROM BAR overlap defect
+    - PCI/ASPM: Make Intel DG2 L1 acceptable latency unlimited
+    - PCI/DPC: Quirk PIO log size for certain Intel Root Ports
+    - PCI/DPC: Quirk PIO log size for Intel Raptor Lake Root Ports
+    - dm-raid: fix lockdep waring in "pers->hot_add_disk"
+    - mac802154: fix llsec key resources release in mac802154_llsec_key_del
+    - swap: comments get_swap_device() with usage rule
+    - mm: swap: fix race between free_swap_and_cache() and swapoff()
+    - mmc: core: Fix switch on gp3 partition
+    - drm/etnaviv: Restore some id values
+    - landlock: Warn once if a Landlock action is requested while disabled
+    - hwmon: (amc6821) add of_match table
+    - ext4: fix corruption during on-line resize
+    - nvmem: meson-efuse: fix function pointer type mismatch
+    - slimbus: core: Remove usage of the deprecated ida_simple_xx() API
+    - phy: tegra: xusb: Add API to retrieve the port number of phy
+    - usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
+    - speakup: Fix 8bit characters from direct synth
+    - PCI/AER: Block runtime suspend when handling errors
+    - nfs: fix UAF in direct writes
+    - kbuild: Move -Wenum-{compare-conditional,enum-conversion} into W=1
+    - PCI: dwc: endpoint: Fix advertised resizable BAR size
+    - vfio/platform: Disable virqfds on cleanup
+    - ksmbd: retrieve number of blocks using vfs_getattr in
+      set_file_allocation_info
+    - ring-buffer: Fix waking up ring buffer readers
+    - ring-buffer: Do not set shortest_full when full target is hit
+    - ring-buffer: Fix resetting of shortest_full
+    - ring-buffer: Fix full_waiters_pending in poll
+    - ring-buffer: Use wait_event_interruptible() in ring_buffer_wait()
+    - soc: fsl: qbman: Always disable interrupts when taking cgr_lock
+    - soc: fsl: qbman: Add helper for sanity checking cgr ops
+    - soc: fsl: qbman: Add CGR update function
+    - soc: fsl: qbman: Use raw spinlock for cgr_lock
+    - s390/zcrypt: fix reference counting on zcrypt card objects
+    - drm/panel: do not return negative error codes from drm_panel_get_modes()
+    - drm/exynos: do not return negative values from .get_modes()
+    - drm/imx/ipuv3: do not return negative values from .get_modes()
+    - drm/vc4: hdmi: do not return negative values from .get_modes()
+    - memtest: use {READ,WRITE}_ONCE in memory scanning
+    - nilfs2: fix failure to detect DAT corruption in btree and direct mappings
+    - nilfs2: prevent kernel bug at submit_bh_wbc()
+    - cpufreq: dt: always allocate zeroed cpumask
+    - x86/CPU/AMD: Update the Zenbleed microcode revisions
+    - NFSD: Fix nfsd_clid_class use of __string_len() macro
+    - net: hns3: tracing: fix hclgevf trace event strings
+    - wireguard: netlink: check for dangling peer via is_dead instead of empty
+      list
+    - wireguard: netlink: access device through ctx instead of peer
+    - ahci: asm1064: correct count of reported ports
+    - ahci: asm1064: asm1166: don't limit reported ports
+    - drm/amdgpu: amdgpu_ttm_gart_bind set gtt bound flag
+    - drm/amd/display: Return the correct HDCP error code
+    - drm/amd/display: Fix noise issue on HDMI AV mute
+    - dm snapshot: fix lockup in dm_exception_table_exit
+    - x86/pm: Work around false positive kmemleak report in msr_build_context()
+    - net: ravb: Add R-Car Gen4 support
+    - cpufreq: brcmstb-avs-cpufreq: fix up "add check for cpufreq_cpu_get's return
+      value"
+    - netfilter: nf_tables: reject constant set with timeout
+    - Drivers: hv: vmbus: Calculate ring buffer size for more efficient use of
+      memory
+    - xfrm: Avoid clang fortify warning in copy_to_user_tmpl()
+    - KVM: SVM: Flush pages under kvm->lock to fix UAF in
+      svm_register_enc_region()
+    - tracing: Use .flush() call to wake up readers
+    - drm/i915: Check before removing mm notifier
+    - USB: usb-storage: Prevent divide-by-0 error in isd200_ata_command
+    - usb: gadget: ncm: Fix handling of zero block length packets
+    - usb: port: Don't try to peer unused USB ports based on location
+    - tty: serial: fsl_lpuart: avoid idle preamble pending if CTS is enabled
+    - mei: me: add arrow lake point S DID
+    - mei: me: add arrow lake point H DID
+    - vt: fix unicode buffer corruption when deleting characters
+    - fs/aio: Check IOCB_AIO_RW before the struct aio_kiocb conversion
+    - tee: optee: Fix kernel panic caused by incorrect error handling
+    - i2c: i801: Avoid potential double call to gpiod_remove_lookup_table
+    - xen/events: close evtchn after mapping cleanup
+    - clocksource/drivers/arm_global_timer: Fix maximum prescaler value
+    - entry: Respect changes to system call number by trace_sys_enter()
+    - minmax: add umin(a, b) and umax(a, b)
+    - swiotlb: Fix alignment checks when both allocation and DMA masks are present
+    - dma-mapping: add dma_opt_mapping_size()
+    - dma-iommu: add iommu_dma_opt_mapping_size()
+    - iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
+    - printk: Update @console_may_schedule in console_trylock_spinning()
+    - tty: serial: imx: Fix broken RS485
+    - x86/asm: Add _ASM_RIP() macro for x86-64 (%rip) suffix
+    - x86/bugs: Add asm helpers for executing VERW
+    - x86/entry_64: Add VERW just before userspace transition
+    - x86/entry_32: Add VERW just before userspace transition
+    - x86/bugs: Use ALTERNATIVE() instead of mds_user_clear static key
+    - KVM/VMX: Use BT+JNC, i.e. EFLAGS.CF to select VMRESUME vs. VMLAUNCH
+    - KVM/VMX: Move VERW closer to VMentry for MDS mitigation
+    - x86/mmio: Disable KVM mitigation when X86_FEATURE_CLEAR_CPU_BUF is set
+    - Documentation/hw-vuln: Add documentation for RFDS
+    - x86/rfds: Mitigate Register File Data Sampling (RFDS)
+    - [Config] updateconfigs for MITIGATION_RFDS
+    - KVM/x86: Export RFDS_NO and RFDS_CLEAR to guests
+    - arch: Introduce CONFIG_FUNCTION_ALIGNMENT
+    - [Config] updateconfigs for FUNCTION_ALIGNMENT
+    - x86/asm: Differentiate between code and function alignment
+    - x86/alternatives: Introduce int3_emulate_jcc()
+    - x86/alternatives: Teach text_poke_bp() to patch Jcc.d32 instructions
+    - x86/static_call: Add support for Jcc tail-calls
+    - fsnotify: pass data_type to fsnotify_name()
+    - fsnotify: pass dentry instead of inode data
+    - fsnotify: clarify contract for create event hooks
+    - fsnotify: Don't insert unmergeable events in hashtable
+    - fanotify: Fold event size calculation to its own function
+    - fanotify: Split fsid check from other fid mode checks
+    - inotify: Don't force FS_IN_IGNORED
+    - fsnotify: Add helper to detect overflow_event
+    - fsnotify: Add wrapper around fsnotify_add_event
+    - fsnotify: Retrieve super block from the data field
+    - fsnotify: Protect fsnotify_handle_inode_event from no-inode events
+    - fsnotify: Pass group argument to free_event
+    - fanotify: Support null inode event in fanotify_dfid_inode
+    - fanotify: Allow file handle encoding for unhashed events
+    - fanotify: Encode empty file handle when no inode is provided
+    - fanotify: Require fid_mode for any non-fd event
+    - fsnotify: Support FS_ERROR event type
+    - fanotify: Reserve UAPI bits for FAN_FS_ERROR
+    - fanotify: Pre-allocate pool of error events
+    - fanotify: Support enqueueing of error events
+    - fanotify: Support merging of error events
+    - fanotify: Wrap object_fh inline space in a creator macro
+    - fanotify: Add helpers to decide whether to report FID/DFID
+    - fanotify: WARN_ON against too large file handles
+    - fanotify: Report fid info for file related file system errors
+    - fanotify: Emit generic error info for error event
+    - fanotify: Allow users to request FAN_FS_ERROR events
+    - ext4: Send notifications on error
+    - docs: Document the FAN_FS_ERROR event
+    - NFS: Remove unnecessary TRACE_DEFINE_ENUM()s
+    - SUNRPC: Tracepoints should display tk_pid and cl_clid as a fixed-size field
+    - NFS: Move generic FS show macros to global header
+    - NFS: Move NFS protocol display macros to global header
+    - NFSD: Optimize DRC bucket pruning
+    - NFSD: move filehandle format declarations out of "uapi".
+    - NFSD: drop support for ancient filehandles
+    - NFSD: simplify struct nfsfh
+    - NFSD: Initialize pointer ni with NULL and not plain integer 0
+    - SUNRPC: Replace the "__be32 *p" parameter to .pc_decode
+    - SUNRPC: Change return value type of .pc_decode
+    - NFSD: Save location of NFSv4 COMPOUND status
+    - SUNRPC: Replace the "__be32 *p" parameter to .pc_encode
+    - SUNRPC: Change return value type of .pc_encode
+    - nfsd: update create verifier comment
+    - NFSD:fix boolreturn.cocci warning
+    - nfsd4: remove obselete comment
+    - ext4: fix error code saved on super block during file system abort
+    - fsnotify: clarify object type argument
+    - fsnotify: separate mark iterator type from object type enum
+    - fanotify: introduce group flag FAN_REPORT_TARGET_FID
+    - fsnotify: generate FS_RENAME event with rich information
+    - fanotify: use macros to get the offset to fanotify_info buffer
+    - fanotify: use helpers to parcel fanotify_info buffer
+    - fanotify: support secondary dir fh and name in fanotify_info
+    - fanotify: record old and new parent and name in FAN_RENAME event
+    - fanotify: record either old name new name or both for FAN_RENAME
+    - fanotify: report old and/or new parent+name in FAN_RENAME event
+    - fanotify: wire up FAN_RENAME event
+    - exit: Implement kthread_exit
+    - exit: Rename module_put_and_exit to module_put_and_kthread_exit
+    - NFSD: handle errors better in write_ports_addfd()
+    - SUNRPC: change svc_get() to return the svc.
+    - SUNRPC/NFSD: clean up get/put functions.
+    - SUNRPC: stop using ->sv_nrthreads as a refcount
+    - nfsd: make nfsd_stats.th_cnt atomic_t
+    - SUNRPC: use sv_lock to protect updates to sv_nrthreads.
+    - NFSD: narrow nfsd_mutex protection in nfsd thread
+    - NFSD: Make it possible to use svc_set_num_threads_sync
+    - SUNRPC: discard svo_setup and rename svc_set_num_threads_sync()
+    - NFSD: simplify locking for network notifier.
+    - lockd: introduce nlmsvc_serv
+    - lockd: simplify management of network status notifiers
+    - lockd: move lockd_start_svc() call into lockd_create_svc()
+    - lockd: move svc_exit_thread() into the thread
+    - lockd: introduce lockd_put()
+    - lockd: rename lockd_create_svc() to lockd_get()
+    - SUNRPC: move the pool_map definitions (back) into svc.c
+    - SUNRPC: always treat sv_nrpools==1 as "not pooled"
+    - lockd: use svc_set_num_threads() for thread start and stop
+    - NFS: switch the callback service back to non-pooled.
+    - NFSD: Remove be32_to_cpu() from DRC hash function
+    - NFSD: Fix inconsistent indenting
+    - NFSD: simplify per-net file cache management
+    - NFSD: Combine XDR error tracepoints
+    - nfsd: improve stateid access bitmask documentation
+    - NFSD: De-duplicate nfsd4_decode_bitmap4()
+    - nfs: block notification on fs with its own ->lock
+    - nfsd4: add refcount for nfsd4_blocked_lock
+    - nfsd: map EBADF
+    - nfsd: Add errno mapping for EREMOTEIO
+    - nfsd: Retry once in nfsd_open on an -EOPENSTALE return
+    - NFSD: Clean up nfsd_vfs_write()
+    - NFSD: De-duplicate net_generic(SVC_NET(rqstp), nfsd_net_id)
+    - nfsd: Add a tracepoint for errors in nfsd4_clone_file_range()
+    - NFSD: Write verifier might go backwards
+    - NFSD: Clean up the nfsd_net::nfssvc_boot field
+    - NFSD: Rename boot verifier functions
+    - NFSD: Trace boot verifier resets
+    - NFSD: Move fill_pre_wcc() and fill_post_wcc()
+    - fsnotify: invalidate dcache before IN_DELETE event
+    - NFSD: Deprecate NFS_OFFSET_MAX
+    - nfsd: Add support for the birth time attribute
+    - orDate: Thu Sep 30 19:19:57 2021 -0400
+    - NFSD: Skip extra computation for RC_NOCACHE case
+    - NFSD: Streamline the rare "found" case
+    - NFSD: Remove NFSD_PROC_ARGS_* macros
+    - SUNRPC: Remove the .svo_enqueue_xprt method
+    - SUNRPC: Merge svc_do_enqueue_xprt() into svc_enqueue_xprt()
+    - SUNRPC: Remove svo_shutdown method
+    - SUNRPC: Rename svc_create_xprt()
+    - SUNRPC: Rename svc_close_xprt()
+    - SUNRPC: Remove svc_shutdown_net()
+    - NFSD: Remove svc_serv_ops::svo_module
+    - NFSD: Move svc_serv_ops::svo_function into struct svc_serv
+    - NFSD: Remove CONFIG_NFSD_V3
+    - [Config] updateconfigs for NFSD_V3
+    - NFSD: Clean up _lm_ operation names
+    - nfsd: fix using the correct variable for sizeof()
+    - fsnotify: fix merge with parent's ignored mask
+    - fsnotify: optimize FS_MODIFY events with no ignored masks
+    - fsnotify: remove redundant parameter judgment
+    - nfsd: Fix a write performance regression
+    - nfsd: Clean up nfsd_file_put()
+    - fanotify: do not allow setting dirent events in mask of non-dir
+    - fs/lock: documentation cleanup. Replace inode->i_lock with flc_lock.
+    - inotify: move control flags from mask to mark flags
+    - fsnotify: pass flags argument to fsnotify_alloc_group()
+    - fsnotify: make allow_dups a property of the group
+    - fsnotify: create helpers for group mark_mutex lock
+    - inotify: use fsnotify group lock helpers
+    - nfsd: use fsnotify group lock helpers
+    - dnotify: use fsnotify group lock helpers
+    - fsnotify: allow adding an inode mark without pinning inode
+    - fanotify: create helper fanotify_mark_user_flags()
+    - fanotify: factor out helper fanotify_mark_update_flags()
+    - fanotify: implement "evictable" inode marks
+    - fanotify: use fsnotify group lock helpers
+    - fanotify: enable "evictable" inode marks
+    - fsnotify: introduce mark type iterator
+    - fsnotify: consistent behavior for parent not watching children
+    - fanotify: fix incorrect fmode_t casts
+    - NFSD: Clean up nfsd_splice_actor()
+    - NFSD: add courteous server support for thread with only delegation
+    - NFSD: add support for share reservation conflict to courteous server
+    - NFSD: move create/destroy of laundry_wq to init_nfsd and exit_nfsd
+    - fs/lock: add helper locks_owner_has_blockers to check for blockers
+    - fs/lock: add 2 callbacks to lock_manager_operations to resolve conflict
+    - NFSD: add support for lock conflict to courteous server
+    - NFSD: Show state of courtesy client in client info
+    - NFSD: Clean up nfsd3_proc_create()
+    - NFSD: Avoid calling fh_drop_write() twice in do_nfsd_create()
+    - NFSD: Refactor nfsd_create_setattr()
+    - NFSD: Refactor NFSv3 CREATE
+    - NFSD: Refactor NFSv4 OPEN(CREATE)
+    - NFSD: Remove do_nfsd_create()
+    - NFSD: Clean up nfsd_open_verified()
+    - NFSD: Instantiate a struct file when creating a regular NFSv4 file
+    - NFSD: Remove dprintk call sites from tail of nfsd4_open()
+    - NFSD: Fix whitespace
+    - NFSD: Move documenting comment for nfsd4_process_open2()
+    - NFSD: Trace filecache opens
+    - SUNRPC: Use RMW bitops in single-threaded hot paths
+    - nfsd: Unregister the cld notifier when laundry_wq create failed
+    - nfsd: Fix null-ptr-deref in nfsd_fill_super()
+    - NFSD: Modernize nfsd4_release_lockowner()
+    - NFSD: Add documenting comment for nfsd4_release_lockowner()
+    - NFSD: nfsd_file_put() can sleep
+    - NFSD: Fix potential use-after-free in nfsd_file_put()
+    - NFS: restore module put when manager exits.
+    - fanotify: refine the validation checks on non-dir inode mask
+    - NFSD: Decode NFSv4 birth time attribute
+    - fs: inotify: Fix typo in inotify comment
+    - fanotify: prepare for setting event flags in ignore mask
+    - fanotify: cleanups for fanotify_mark() input validations
+    - fanotify: introduce FAN_MARK_IGNORE
+    - fsnotify: Fix comment typo
+    - NLM: Defend against file_lock changes after vfs_test_lock()
+    - NFSD: Instrument fh_verify()
+    - NFSD: Fix space and spelling mistake
+    - nfsd: remove redundant assignment to variable len
+    - NFSD: Demote a WARN to a pr_warn()
+    - NFSD: Report filecache LRU size
+    - NFSD: Report count of calls to nfsd_file_acquire()
+    - NFSD: Report count of freed filecache items
+    - NFSD: Report average age of filecache items
+    - NFSD: Add nfsd_file_lru_dispose_list() helper
+    - NFSD: Refactor nfsd_file_gc()
+    - NFSD: Refactor nfsd_file_lru_scan()
+    - NFSD: Report the number of items evicted by the LRU walk
+    - NFSD: Record number of flush calls
+    - NFSD: Zero counters when the filecache is re-initialized
+    - NFSD: Hook up the filecache stat file
+    - NFSD: WARN when freeing an item still linked via nf_lru
+    - NFSD: Trace filecache LRU activity
+    - NFSD: Leave open files out of the filecache LRU
+    - NFSD: Fix the filecache LRU shrinker
+    - NFSD: Never call nfsd_file_gc() in foreground paths
+    - NFSD: No longer record nf_hashval in the trace log
+    - NFSD: Remove lockdep assertion from unhash_and_release_locked()
+    - NFSD: nfsd_file_unhash can compute hashval from nf->nf_inode
+    - NFSD: Refactor __nfsd_file_close_inode()
+    - NFSD: nfsd_file_hash_remove can compute hashval
+    - NFSD: Remove nfsd_file::nf_hashval
+    - NFSD: Replace the "init once" mechanism
+    - NFSD: Set up an rhashtable for the filecache
+    - NFSD: Convert the filecache to use rhashtable
+    - NFSD: Clean up unused code after rhashtable conversion
+    - NFSD: Separate tracepoints for acquire and create
+    - NFSD: Move nfsd_file_trace_alloc() tracepoint
+    - NFSD: NFSv4 CLOSE should release an nfsd_file immediately
+    - NFSD: Ensure nf_inode is never dereferenced
+    - NFSD: refactoring v4 specific code to a helper in nfs4state.c
+    - NFSD: keep track of the number of v4 clients in the system
+    - NFSD: limit the number of v4 clients to 1024 per 1GB of system memory
+    - nfsd: silence extraneous printk on nfsd.ko insertion
+    - NFSD: Optimize nfsd4_encode_operation()
+    - NFSD: Optimize nfsd4_encode_fattr()
+    - NFSD: Clean up SPLICE_OK in nfsd4_encode_read()
+    - NFSD: Add an nfsd4_read::rd_eof field
+    - NFSD: Optimize nfsd4_encode_readv()
+    - NFSD: Simplify starting_len
+    - NFSD: Use xdr_pad_size()
+    - NFSD: Clean up nfsd4_encode_readlink()
+    - NFSD: Fix strncpy() fortify warning
+    - NFSD: nfserrno(-ENOMEM) is nfserr_jukebox
+    - NFSD: Shrink size of struct nfsd4_copy_notify
+    - NFSD: Shrink size of struct nfsd4_copy
+    - NFSD: Reorder the fields in struct nfsd4_op
+    - NFSD: Make nfs4_put_copy() static
+    - NFSD: Replace boolean fields in struct nfsd4_copy
+    - NFSD: Refactor nfsd4_cleanup_inter_ssc() (1/2)
+    - NFSD: Refactor nfsd4_cleanup_inter_ssc() (2/2)
+    - NFSD: Refactor nfsd4_do_copy()
+    - NFSD: Remove kmalloc from nfsd4_do_async_copy()
+    - NFSD: Add nfsd4_send_cb_offload()
+    - NFSD: Move copy offload callback arguments into a separate structure
+    - NFSD: drop fh argument from alloc_init_deleg
+    - NFSD: verify the opened dentry after setting a delegation
+    - NFSD: introduce struct nfsd_attrs
+    - NFSD: set attributes when creating symlinks
+    - NFSD: add security label to struct nfsd_attrs
+    - NFSD: add posix ACLs to struct nfsd_attrs
+    - NFSD: change nfsd_create()/nfsd_symlink() to unlock directory before
+      returning.
+    - NFSD: always drop directory lock in nfsd_unlink()
+    - NFSD: only call fh_unlock() once in nfsd_link()
+    - NFSD: reduce locking in nfsd_lookup()
+    - NFSD: use explicit lock/unlock for directory ops
+    - NFSD: use (un)lock_inode instead of fh_(un)lock for file operations
+    - NFSD: discard fh_locked flag and fh_lock/fh_unlock
+    - NFSD: fix regression with setting ACLs.
+    - nfsd_splice_actor(): handle compound pages
+    - NFSD: move from strlcpy with unused retval to strscpy
+    - lockd: move from strlcpy with unused retval to strscpy
+    - NFSD enforce filehandle check for source file in COPY
+    - NFSD: remove redundant variable status
+    - nfsd: Avoid some useless tests
+    - nfsd: Propagate some error code returned by memdup_user()
+    - NFSD: Increase NFSD_MAX_OPS_PER_COMPOUND
+    - NFSD: drop fname and flen args from nfsd_create_locked()
+    - nfsd: clean up mounted_on_fileid handling
+    - nfsd: remove nfsd4_prepare_cb_recall() declaration
+    - NFSD: Replace dprintk() call site in fh_verify()
+    - NFSD: Trace NFSv4 COMPOUND tags
+    - NFSD: Add tracepoints to report NFSv4 callback completions
+    - NFSD: Add a mechanism to wait for a DELEGRETURN
+    - NFSD: Refactor nfsd_setattr()
+    - NFSD: Make nfsd4_setattr() wait before returning NFS4ERR_DELAY
+    - NFSD: Make nfsd4_rename() wait before returning NFS4ERR_DELAY
+    - NFSD: Make nfsd4_remove() wait before returning NFS4ERR_DELAY
+    - NFSD: keep track of the number of courtesy clients in the system
+    - NFSD: add shrinker to reap courtesy clients on low memory condition
+    - SUNRPC: Parametrize how much of argsize should be zeroed
+    - NFSD: Reduce amount of struct nfsd4_compoundargs that needs clearing
+    - NFSD: Refactor common code out of dirlist helpers
+    - NFSD: Use xdr_inline_decode() to decode NFSv3 symlinks
+    - NFSD: Clean up WRITE arg decoders
+    - NFSD: Clean up nfs4svc_encode_compoundres()
+    - NFSD: Remove unused nfsd4_compoundargs::cachetype field
+    - NFSD: Pack struct nfsd4_compoundres
+    - nfsd: use DEFINE_PROC_SHOW_ATTRIBUTE to define nfsd_proc_ops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define export_features_fops and
+      supported_enctypes_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define client_info_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define nfsd_reply_cache_stats_fops
+    - nfsd: use DEFINE_SHOW_ATTRIBUTE to define nfsd_file_cache_stats_fops
+    - NFSD: Rename the fields in copy_stateid_t
+    - nfsd: only fill out return pointer on success in nfsd4_lookup_stateid
+    - nfsd: fix comments about spinlock handling with delegations
+    - nfsd: make nfsd4_run_cb a bool return function
+    - nfsd: extra checks when freeing delegation stateids
+    - fs/notify: constify path
+    - fsnotify: remove unused declaration
+    - fanotify: Remove obsoleted fanotify_event_has_path()
+    - nfsd: fix nfsd_file_unhash_and_dispose
+    - nfsd: rework hashtable handling in nfsd_do_file_acquire
+    - NFSD: unregister shrinker when nfsd_init_net() fails
+    - nfsd: ensure we always call fh_verify_error tracepoint
+    - nfsd: fix net-namespace logic in __nfsd_file_cache_purge
+    - nfsd: fix use-after-free in nfsd_file_do_acquire tracepoint
+    - nfsd: put the export reference in nfsd4_verify_deleg_dentry
+    - NFSD: Fix trace_nfsd_fh_verify_err() crasher
+    - NFSD: Fix reads with a non-zero offset that don't end on a page boundary
+    - lockd: use locks_inode_context helper
+    - nfsd: use locks_inode_context helper
+    - NFSD: Simplify READ_PLUS
+    - NFSD: Remove redundant assignment to variable host_err
+    - NFSD: Finish converting the NFSv3 GETACL result encoder
+    - nfsd: ignore requests to disable unsupported versions
+    - nfsd: move nfserrno() to vfs.c
+    - nfsd: allow disabling NFSv2 at compile time
+    - [Config] updateconfigs for NFSD_V2
+    - exportfs: use pr_debug for unreachable debug statements
+    - NFSD: Pass the target nfsd_file to nfsd_commit()
+    - NFSD: Revert "NFSD: NFSv4 CLOSE should release an nfsd_file immediately"
+    - NFSD: Add an NFSD_FILE_GC flag to enable nfsd_file garbage collection
+    - NFSD: Flesh out a documenting comment for filecache.c
+    - NFSD: Clean up nfs4_preprocess_stateid_op() call sites
+    - NFSD: Trace stateids returned via DELEGRETURN
+    - NFSD: Trace delegation revocations
+    - NFSD: Use const pointers as parameters to fh_ helpers
+    - NFSD: Update file_hashtbl() helpers
+    - NFSD: Clean up nfsd4_init_file()
+    - NFSD: Add a nfsd4_file_hash_remove() helper
+    - NFSD: Clean up find_or_add_file()
+    - NFSD: Refactor find_file()
+    - NFSD: Use rhashtable for managing nfs4_file objects
+    - NFSD: Fix licensing header in filecache.c
+    - nfsd: remove the pages_flushed statistic from filecache
+    - nfsd: reorganize filecache.c
+    - filelock: add a new locks_inode_context accessor function
+    - nfsd: fix up the filecache laundrette scheduling
+    - NFSD: Add an nfsd_file_fsync tracepoint
+    - nfsd: return error if nfs4_setacl fails
+    - NFSD: Use struct_size() helper in alloc_session()
+    - lockd: set missing fl_flags field when retrieving args
+    - lockd: ensure we use the correct file descriptor when unlocking
+    - lockd: fix file selection in nlmsvc_cancel_blocked
+    - trace: Relocate event helper files
+    - NFSD: refactoring courtesy_client_reaper to a generic low memory shrinker
+    - NFSD: add support for sending CB_RECALL_ANY
+    - NFSD: add delegation reaper to react to low memory condition
+    - NFSD: add CB_RECALL_ANY tracepoints
+    - NFSD: Use only RQ_DROPME to signal the need to drop a reply
+    - NFSD: Avoid clashing function prototypes
+    - nfsd: rework refcounting in filecache
+    - nfsd: fix handling of cached open files in nfsd4_open codepath
+    - Revert "SUNRPC: Use RMW bitops in single-threaded hot paths"
+    - NFSD: Use set_bit(RQ_DROPME)
+    - NFSD: register/unregister of nfsd-client shrinker at nfsd startup/shutdown
+      time
+    - NFSD: replace delayed_work with work_struct for nfsd_client_shrinker
+    - nfsd: don't free files unconditionally in __nfsd_file_cache_purge
+    - nfsd: don't destroy global nfs4_file table in per-net shutdown
+    - NFSD: enhance inter-server copy cleanup
+    - nfsd: allow nfsd_file_get to sanely handle a NULL pointer
+    - nfsd: clean up potential nfsd_file refcount leaks in COPY codepath
+    - NFSD: fix leaked reference count of nfsd4_ssc_umount_item
+    - nfsd: don't hand out delegation on setuid files being opened for write
+    - NFSD: fix problems with cleanup on errors in nfsd4_copy
+    - nfsd: fix courtesy client with deny mode handling in nfs4_upgrade_open
+    - nfsd: don't fsync nfsd_files on last close
+    - NFSD: copy the whole verifier in nfsd_copy_write_verifier
+    - NFSD: Protect against filesystem freezing
+    - nfsd: don't replace page in rq_pages if it's a continuation of last page
+    - nfsd: call op_release, even when op_func returns an error
+    - nfsd: don't open-code clear_and_wake_up_bit
+    - nfsd: NFSD_FILE_KEY_INODE only needs to find GC'ed entries
+    - nfsd: simplify test_bit return in NFSD_FILE_KEY_FULL comparator
+    - nfsd: don't kill nfsd_files because of lease break error
+    - nfsd: add some comments to nfsd_file_do_acquire
+    - nfsd: don't take/put an extra reference when putting a file
+    - nfsd: update comment over __nfsd_file_cache_purge
+    - nfsd: allow reaping files still under writeback
+    - NFSD: Convert filecache to rhltable
+    - nfsd: simplify the delayed disposal list code
+    - NFSD: Fix problem of COMMIT and NFS4ERR_DELAY in infinite loop
+    - nfsd: make a copy of struct iattr before calling notify_change
+    - nfsd: fix double fget() bug in __write_ports_addfd()
+    - lockd: drop inappropriate svc_get() from locked_get()
+    - NFSD: Add an nfsd4_encode_nfstime4() helper
+    - nfsd: Fix creation time serialization order
+    - nfsd: Simplify code around svc_exit_thread() call in nfsd()
+    - nfsd: separate nfsd_last_thread() from nfsd_put()
+    - Documentation: Add missing documentation for EXPORT_OP flags
+    - NFSD: fix possible oops when nfsd/pool_stats is closed.
+    - nfsd: call nfsd_last_thread() before final nfsd_put()
+    - nfsd: drop the nfsd_put helper
+    - nfsd: fix RELEASE_LOCKOWNER
+    - nfsd: don't take fi_lock in nfsd_break_deleg_cb()
+    - nfsd: don't call locks_release_private() twice concurrently
+    - nfsd: Fix a regression in nfsd_setattr()
+    - perf/core: Fix reentry problem in perf_output_read_group()
+    - efivarfs: Request at most 512 bytes for variable names
+    - powerpc: xor_vmx: Add '-mhard-float' to CFLAGS
+    - selftests: mptcp: diag: return KSFT_FAIL not test_cnt
+    - vfio/pci: Disable auto-enable of exclusive INTx IRQ
+    - vfio/pci: Lock external INTx masking ops
+    - vfio: Introduce interface to flush virqfd inject workqueue
+    - vfio/pci: Create persistent INTx handler
+    - vfio/platform: Create persistent IRQ handlers
+    - vfio/fsl-mc: Block calling interrupt handler without trigger
+    - serial: sc16is7xx: convert from _raw_ to _noinc_ regmap functions for FIFO
+    - mm/migrate: set swap entry values of THP tail pages properly.
+    - init: open /initrd.image with O_LARGEFILE
+    - btrfs: zoned: use zone aware sb location for scrub
+    - wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes
+    - exec: Fix NOMMU linux_binprm::exec in transfer_args_to_stack()
+    - hexagon: vmlinux.lds.S: handle attributes section
+    - mmc: core: Initialize mmc_blk_ioc_data
+    - mmc: core: Avoid negative index with array access
+    - net: ll_temac: platform_get_resource replaced by wrong function
+    - drm/i915/gt: Reset queue_priority_hint on parking
+    - drm/amdgpu: Use drm_mode_copy()
+    - drm/amd/display: Preserve original aspect ratio in create stream
+    - ALSA: sh: aica: reorder cleanup operations to avoid UAF bugs
+    - scsi: core: Fix unremoved procfs host directory regression
+    - staging: vc04_services: changen strncpy() to strscpy_pad()
+    - staging: vc04_services: fix information leak in create_component()
+    - USB: core: Add hub_get() and hub_put() routines
+    - usb: dwc2: host: Fix remote wakeup from hibernation
+    - usb: dwc2: host: Fix hibernation flow
+    - usb: dwc2: host: Fix ISOC flow in DDMA mode
+    - usb: dwc2: gadget: Fix exiting from clock gating
+    - usb: dwc2: gadget: LPM flow fix
+    - usb: udc: remove warning when queue disabled ep
+    - usb: typec: ucsi: Ack unsupported commands
+    - usb: typec: ucsi: Clear UCSI_CCI_RESET_COMPLETE before reset
+    - scsi: qla2xxx: Prevent command send on chip reset
+    - scsi: qla2xxx: Fix N2N stuck connection
+    - scsi: qla2xxx: Split FCE|EFT trace control
+    - scsi: qla2xxx: NVME|FCP prefer flag not being honored
+    - scsi: qla2xxx: Fix command flush on cable pull
+    - scsi: qla2xxx: Fix double free of fcport
+    - scsi: qla2xxx: Change debug message during driver unload
+    - scsi: qla2xxx: Delay I/O Abort on PCI error
+    - x86/cpu: Enable STIBP on AMD if Automatic IBRS is enabled
+    - PCI/DPC: Quirk PIO log size for Intel Ice Lake Root Ports
+    - scsi: lpfc: Correct size for wqe for memset()
+    - USB: core: Fix deadlock in usb_deauthorize_interface()
+    - scsi: usb: Call scsi_done() directly
+    - scsi: usb: Stop using the SCSI pointer
+    - USB: UAS: return ENODEV when submit urbs fail with device not attached
+    - nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet
+    - mlxbf_gige: stop PHY during open() error paths
+    - iwlwifi: mvm: rfi: use kmemdup() to replace kzalloc + memcpy
+    - wifi: iwlwifi: mvm: rfi: fix potential response leaks
+    - ixgbe: avoid sleeping allocation in ixgbe_ipsec_vf_add_sa()
+    - s390/qeth: handle deferred cc1
+    - tcp: properly terminate timers for kernel sockets
+    - ACPICA: debugger: check status of acpi_evaluate_object() in
+      acpi_db_walk_for_fields()
+    - mlxbf_gige: call request_irq() after NAPI initialized
+    - bpf: Protect against int overflow for stack access size
+    - Octeontx2-af: fix pause frame configuration in GMP mode
+    - dm integrity: fix out-of-range warning
+    - r8169: fix issue caused by buggy BIOS on certain boards with RTL8168d
+    - x86/cpufeatures: Add new word for scattered features
+    - x86/cpufeatures: Add CPUID_LNX_5 to track recently added Linux-defined word
+    - arm64: dts: qcom: sc7180-trogdor: mark bluetooth address as broken
+    - Bluetooth: hci_event: set the conn encrypted before conn establishes
+    - Bluetooth: Fix TOCTOU in HCI debugfs implementation
+    - xen-netfront: Add missing skb_mark_for_recycle
+    - net/rds: fix possible cp null dereference
+    - locking/rwsem: Disable preemption while trying for rwsem lock
+    - io_uring: ensure '0' is returned on file registration success
+    - Revert "x86/mm/ident_map: Use gbpages only where full GB page should be
+      mapped."
+    - mm, vmscan: prevent infinite loop for costly GFP_NOIO | __GFP_RETRY_MAYFAIL
+      allocations
+    - thermal: devfreq_cooling: Fix perf state when calculate dfc res_util
+    - KVM: x86: Bail to userspace if emulation of atomic user access faults
+    - KVM: x86: Mark target gfn of emulated atomic instruction as dirty
+    - netfilter: nf_tables: reject new basechain after table flag update
+    - netfilter: nf_tables: flush pending destroy work before exit_net release
+    - netfilter: nf_tables: Fix potential data-race in __nft_flowtable_type_get()
+    - netfilter: validate user input for expected length
+    - vboxsf: Avoid an spurious warning if load_nls_xxx() fails
+    - bpf, sockmap: Prevent lock inversion deadlock in map delete elem
+    - net/sched: act_skbmod: prevent kernel-infoleak
+    - net: stmmac: fix rx queue priority assignment
+    - selftests: net: gro fwd: update vxlan GRO test expectations
+    - erspan: make sure erspan_base_hdr is present in skb->head
+    - selftests: reuseaddr_conflict: add missing new line at the end of the output
+    - ipv6: Fix infinite recursion in fib6_dump_done().
+    - mlxbf_gige: stop interface during shutdown
+    - udp: do not accept non-tunnel GSO skbs landing in a tunnel
+    - udp: do not transition UDP GRO fraglist partial checksums to unnecessary
+    - udp: prevent local UDP tunnel packets from being GROed
+    - octeontx2-af: Fix issue with loading coalesced KPU profiles
+    - octeontx2-pf: check negative error code in otx2_open()
+    - i40e: fix i40e_count_filters() to count only active/new filters
+    - i40e: fix vf may be used uninitialized in this function warning
+    - scsi: qla2xxx: Update manufacturer details
+    - scsi: qla2xxx: Update manufacturer detail
+    - Revert "usb: phy: generic: Get the vbus supply"
+    - i40e: Store the irq number in i40e_q_vector
+    - i40e: Remove _t suffix from enum type names
+    - i40e: Enforce software interrupt during busy-poll exit
+    - net: usb: asix: suspend embedded PHY if external is used
+    - drivers: net: convert to boolean for the mac_managed_pm flag
+    - net: fec: Set mac_managed_pm during probe
+    - net: ravb: Always process TX descriptor ring
+    - ASoC: rt5682-sdw: fix locking sequence
+    - ASoC: rt711-sdca: fix locking sequence
+    - ASoC: rt711-sdw: fix locking sequence
+    - ASoC: ops: Fix wraparound for mask in snd_soc_get_volsw
+    - ata: sata_sx4: fix pdc20621_get_from_dimm() on 64-bit
+    - scsi: mylex: Fix sysfs buffer lengths
+    - ata: sata_mv: Fix PCI device ID table declaration compilation warning
+    - nfsd: hold a lighter-weight client reference over CB_RECALL_ANY
+    - HID: uhid: Use READ_ONCE()/WRITE_ONCE() for ->running
+    - openrisc: Fix pagewalk usage in arch_dma_{clear, set}_uncached
+    - fs/pipe: Fix lockdep false-positive in watchqueue pipe_write()
+    - ALSA: hda/realtek: Update Panasonic CF-SZ6 quirk to support headset with
+      microphone
+    - driver core: Introduce device_link_wait_removal()
+    - of: dynamic: Synchronize of_changeset_destroy() with the devlink removals
+    - x86/mce: Make sure to grab mce_sysfs_mutex in set_bank()
+    - s390/entry: align system call table on 8 bytes
+    - riscv: Fix spurious errors from __get/put_kernel_nofault
+    - riscv: process: Fix kernel gp leakage
+    - x86/bugs: Fix the SRSO mitigation on Zen3/4
+    - x86/retpoline: Do the necessary fixup to the Zen3/4 srso return thunk for
+      !SRSO
+    - mptcp: don't account accept() of non-MPC client as fallback to TCP
+    - mm/secretmem: fix GUP-fast succeeding on secretmem folios
+    - gro: fix ownership transfer
+    - nvme: fix miss command type check
+    - x86: set SPECTRE_BHI_ON as default
+    - Linux 5.15.154
+  * CVE-2024-23307
+    - md/raid5: fix atomicity violation in raid5_cache_count
+  * CVE-2024-26828
+    - cifs: fix underflow in parse_server_interfaces()
+  * CVE-2024-24861
+    - media: xc4000: Fix atomicity violation in xc4000_get_frequency
+  * CVE-2024-26642
+    - netfilter: nf_tables: disallow anonymous set with timeout flag
+  * CVE-2024-26926
+    - binder: check offset alignment in binder_get_object()
+  * CVE-2024-26922
+    - drm/amdgpu: validate the parameters of bo mapping operations more clearly
+  * CVE-2023-6039
+    - timers: Silently ignore timers with a NULL function
+  * CVE-2024-26924
+    - netfilter: nft_set_pipapo: do not free live element
+  * CVE-2024-26643
+    - netfilter: nf_tables: mark set as dead when unbinding anonymous set with
+      timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Tue, 18 Jun 2024 09:09:18 +1000
+
+linux-xilinx-zynqmp (5.15.0-1031.35) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1031.35 -proposed tracker (LP: #2068238)
+
+  [ Ubuntu: 5.15.0-113.123 ]
+
+  * jammy/linux: 5.15.0-113.123 -proposed tracker (LP: #2068242)
+  * CVE-2024-26924
+    - netfilter: nft_set_pipapo: do not free live element
+  * CVE-2024-26643
+    - netfilter: nf_tables: mark set as dead when unbinding anonymous set with
+      timeout
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 14 Jun 2024 09:20:22 +1000
+
+linux-xilinx-zynqmp (5.15.0-1030.34) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1030.34 -proposed tracker (LP: #2063760)
+
+  * Revert "crypto: api - Disallow identical driver names" (LP: #2064724)
+    - Revert "crypto: api - Disallow identical driver names"
+
+  [ Ubuntu: 5.15.0-112.122 ]
+
+  * jammy/linux: 5.15.0-112.122 -proposed tracker (LP: #2065898)
+  * CVE-2024-21823
+    - dmanegine: idxd: reformat opcap output to match bitmap_parse() input
+    - dmaengine: idxd: add WQ operation cap restriction support
+    - dmaengine: idxd: add knob for enqcmds retries
+    - VFIO: Add the SPR_DSA and SPR_IAX devices to the denylist
+    - dmaengine: idxd: add a new security check to deal with a hardware erratum
+    - dmaengine: idxd: add a write() method for applications to submit work
+
+  [ Ubuntu: 5.15.0-111.121 ]
+
+  * jammy/linux: 5.15.0-111.121 -proposed tracker (LP: #2063763)
+  * RTL8852BE fw security fail then lost WIFI function during suspend/resume
+    cycle (LP: #2063096)
+    - wifi: rtw89: download firmware with five times retry
+  * Mount CIFS fails with Permission denied (LP: #2061986)
+    - cifs: fix ntlmssp auth when there is no key exchange
+  * USB stick can't be detected (LP: #2040948)
+    - usb: Disable USB3 LPM at shutdown
+  * Jammy update: v5.15.153 upstream stable release (LP: #2063290)
+    - io_uring/unix: drop usage of io_uring socket
+    - io_uring: drop any code related to SCM_RIGHTS
+    - selftests: tls: use exact comparison in recv_partial
+    - ASoC: rt5645: Make LattePanda board DMI match more precise
+    - x86/xen: Add some null pointer checking to smp.c
+    - MIPS: Clear Cause.BD in instruction_pointer_set
+    - HID: multitouch: Add required quirk for Synaptics 0xcddc device
+    - gen_compile_commands: fix invalid escape sequence warning
+    - RDMA/mlx5: Fix fortify source warning while accessing Eth segment
+    - RDMA/mlx5: Relax DEVX access upon modify commands
+    - riscv: dts: sifive: add missing #interrupt-cells to pmic
+    - x86/mm: Move is_vsyscall_vaddr() into asm/vsyscall.h
+    - x86/mm: Disallow vsyscall page read for copy_from_kernel_nofault()
+    - net/iucv: fix the allocation size of iucv_path_table array
+    - parisc/ftrace: add missing CONFIG_DYNAMIC_FTRACE check
+    - block: sed-opal: handle empty atoms when parsing response
+    - dm-verity, dm-crypt: align "struct bvec_iter" correctly
+    - scsi: mpt3sas: Prevent sending diag_reset when the controller is ready
+    - ALSA: hda/realtek - ALC285 reduce pop noise from Headphone port
+    - drm/amdgpu: Enable gpu reset for S3 abort cases on Raven series
+    - Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security
+    - firewire: core: use long bus reset on gap count error
+    - ASoC: Intel: bytcr_rt5640: Add an extra entry for the Chuwi Vi8 tablet
+    - Input: gpio_keys_polled - suppress deferred probe error for gpio
+    - ASoC: wm8962: Enable oscillator if selecting WM8962_FLL_OSC
+    - ASoC: wm8962: Enable both SPKOUTR_ENA and SPKOUTL_ENA in mono mode
+    - ASoC: wm8962: Fix up incorrect error message in wm8962_set_fll
+    - do_sys_name_to_handle(): use kzalloc() to fix kernel-infoleak
+    - s390/dasd: put block allocation in separate function
+    - s390/dasd: add query PPRC function
+    - s390/dasd: add copy pair setup
+    - s390/dasd: add autoquiesce feature
+    - s390/dasd: Use dev_*() for device log messages
+    - s390/dasd: fix double module refcount decrement
+    - fs/select: rework stack allocation hack for clang
+    - md: Don't clear MD_CLOSING when the raid is about to stop
+    - lib/cmdline: Fix an invalid format specifier in an assertion msg
+    - time: test: Fix incorrect format specifier
+    - rtc: test: Fix invalid format specifier.
+    - aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts
+    - timekeeping: Fix cross-timestamp interpolation on counter wrap
+    - timekeeping: Fix cross-timestamp interpolation corner case decision
+    - timekeeping: Fix cross-timestamp interpolation for non-x86
+    - sched/fair: Take the scheduling domain into account in select_idle_core()
+    - wifi: ath10k: fix NULL pointer dereference in
+      ath10k_wmi_tlv_op_pull_mgmt_tx_compl_ev()
+    - wifi: b43: Stop/wake correct queue in DMA Tx path when QoS is disabled
+    - wifi: b43: Stop/wake correct queue in PIO Tx path when QoS is disabled
+    - wifi: b43: Stop correct queue in DMA worker when QoS is disabled
+    - wifi: b43: Disable QoS for bcm4331
+    - wifi: wilc1000: fix declarations ordering
+    - wifi: wilc1000: fix RCU usage in connect path
+    - wifi: rtl8xxxu: add cancel_work_sync() for c2hcmd_work
+    - wifi: wilc1000: fix multi-vif management when deleting a vif
+    - wifi: mwifiex: debugfs: Drop unnecessary error check for
+      debugfs_create_dir()
+    - cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
+    - cpufreq: Explicitly include correct DT includes
+    - cpufreq: mediatek-hw: Wait for CPU supplies before probing
+    - sock_diag: annotate data-races around sock_diag_handlers[family]
+    - inet_diag: annotate data-races around inet_diag_table[]
+    - bpftool: Silence build warning about calloc()
+    - af_unix: Annotate data-race of gc_in_progress in wait_for_unix_gc().
+    - cpufreq: mediatek-hw: Don't error out if supply is not found
+    - arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM
+    - arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL
+      board
+    - arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD
+      card
+    - arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO
+      voltage
+    - arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL
+      board
+    - wifi: ath9k: delay all of ath9k_wmi_event_tasklet() until init is complete
+    - wifi: iwlwifi: mvm: report beacon protection failures
+    - wifi: iwlwifi: dbg-tlv: ensure NUL termination
+    - wifi: iwlwifi: fix EWRD table validity check
+    - arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
+    - pwm: atmel-hlcdc: Convert to platform remove callback returning void
+    - pwm: atmel-hlcdc: Use consistent variable naming
+    - pwm: atmel-hlcdc: Fix clock imbalance related to suspend support
+    - net: blackhole_dev: fix build warning for ethh set but not used
+    - wifi: libertas: fix some memleaks in lbs_allocate_cmd_buffer()
+    - pwm: sti: Implement .apply() callback
+    - pwm: sti: Fix capture for st,pwm-num-chan < st,capture-num-chan
+    - wifi: iwlwifi: mvm: don't set replay counters to 0xff
+    - s390/vdso: drop '-fPIC' from LDFLAGS
+    - ipv6: mcast: remove one synchronize_net() barrier in ipv6_mc_down()
+    - arm64: dts: mt8183: kukui: Add Type C node
+    - arm64: dts: mt8183: kukui: Split out keyboard node and describe detachables
+    - arm64: dts: mt8183: Move CrosEC base detection node to kukui-based DTs
+    - arm64: dts: mediatek: mt7622: add missing "device_type" to memory nodes
+    - bpf: Mark bpf_spin_{lock,unlock}() helpers with notrace correctly
+    - wireless: Remove redundant 'flush_workqueue()' calls
+    - wifi: wilc1000: prevent use-after-free on vif when cleaning up all
+      interfaces
+    - ACPI: processor_idle: Fix memory leak in acpi_processor_power_exit()
+    - bus: tegra-aconnect: Update dependency to ARCH_TEGRA
+    - [Config]: update CONFIG_TEGRA_ACONNECT
+    - iommu/amd: Mark interrupt as managed
+    - wifi: brcmsmac: avoid function pointer casts
+    - net: ena: Remove ena_select_queue
+    - ARM: dts: arm: realview: Fix development chip ROM compatible value
+    - arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
+    - arm64: dts: renesas: r8a779a0: Correct avb[01] reg sizes
+    - ARM: dts: imx6dl-yapp4: Move phy reset into switch node
+    - ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address
+    - ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node
+    - arm64: dts: marvell: reorder crypto interrupts on Armada SoCs
+    - ACPI: resource: Add Infinity laptops to irq1_edge_low_force_override
+    - ACPI: resource: Do IRQ override on Lunnen Ground laptops
+    - ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override
+    - ACPI: scan: Fix device check notification handling
+    - x86, relocs: Ignore relocations in .notes section
+    - SUNRPC: fix some memleaks in gssx_dec_option_array
+    - mmc: wmt-sdmmc: remove an incorrect release_mem_region() call in the .remove
+      function
+    - wifi: rtw88: 8821c: Fix false alarm count
+    - PCI: Make pci_dev_is_disconnected() helper public for other drivers
+    - iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected
+    - igb: move PEROUT and EXTTS isr logic to separate functions
+    - igb: Fix missing time sync events
+    - Bluetooth: Remove superfluous call to hci_conn_check_pending()
+    - Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855
+    - Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()
+    - Bluetooth: hci_core: Fix possible buffer overflow
+    - sr9800: Add check for usbnet_get_endpoints
+    - bpf: Fix DEVMAP_HASH overflow check on 32-bit arches
+    - bpf: Fix hashtab overflow check on 32-bit arches
+    - bpf: Fix stackmap overflow check on 32-bit arches
+    - ipv6: fib6_rules: flush route cache when rule is changed
+    - net: ip_tunnel: make sure to pull inner header in ip_tunnel_rcv()
+    - net: phy: fix phy_get_internal_delay accessing an empty array
+    - net: hns3: fix kernel crash when 1588 is received on HIP08 devices
+    - net: hns3: fix port duplex configure error in IMP reset
+    - net: phy: DP83822: enable rgmii mode if phy_interface_is_rgmii
+    - net: phy: dp83822: Fix RGMII TX delay configuration
+    - OPP: debugfs: Fix warning around icc_get_name()
+    - tcp: fix incorrect parameter validation in the do_tcp_getsockopt() function
+    - net: Change sock_getsockopt() to take the sk ptr instead of the sock ptr
+    - bpf: net: Change sk_getsockopt() to take the sockptr_t argument
+    - bpf: net: Change do_ip_getsockopt() to take the sockptr_t argument
+    - ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt()
+      function
+    - l2tp: fix incorrect parameter validation in the pppol2tp_getsockopt()
+      function
+    - udp: fix incorrect parameter validation in the udp_lib_getsockopt() function
+    - net: kcm: fix incorrect parameter validation in the kcm_getsockopt) function
+    - net/x25: fix incorrect parameter validation in the x25_getsockopt() function
+    - nfp: flower: handle acti_netdevs allocation failure
+    - dm raid: fix false positive for requeue needed during reshape
+    - dm: call the resume method on internal suspend
+    - drm/tegra: dsi: Add missing check for of_find_device_by_node
+    - drm/tegra: dpaux: Populate AUX bus
+    - drm/tegra: dpaux: Fix PM disable depth imbalance in tegra_dpaux_probe
+    - drm/tegra: dsi: Make use of the helper function dev_err_probe()
+    - drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()
+    - drm/tegra: dsi: Fix missing pm_runtime_disable() in the error handling path
+      of tegra_dsi_probe()
+    - drm/tegra: dc: rgb: Allow changing PLLD rate on Tegra30+
+    - drm/tegra: rgb: Fix some error handling paths in tegra_dc_rgb_probe()
+    - drm/tegra: rgb: Fix missing clk_put() in the error handling paths of
+      tegra_dc_rgb_probe()
+    - drm/tegra: output: Fix missing i2c_put_adapter() in the error handling paths
+      of tegra_output_probe()
+    - drm/rockchip: inno_hdmi: Fix video timing
+    - drm: Don't treat 0 as -1 in drm_fixp2int_ceil
+    - drm/ttm: add ttm_resource_fini v2
+    - drm/vmwgfx: fix a memleak in vmw_gmrid_man_get_node
+    - drm/rockchip: lvds: do not overwrite error code
+    - drm/rockchip: lvds: do not print scary message when probing defer
+    - drm/lima: fix a memleak in lima_heap_alloc
+    - dmaengine: tegra210-adma: Update dependency to ARCH_TEGRA
+    - [Config]: update CONFIG_TEGRA210_ADMA
+    - media: tc358743: register v4l2 async device only after successful setup
+    - PCI/DPC: Print all TLP Prefixes, not just the first
+    - perf record: Fix possible incorrect free in record__switch_output()
+    - HID: lenovo: Add middleclick_workaround sysfs knob for cptkbd
+    - drm/amd/display: Fix a potential buffer overflow in 'dp_dsc_clock_en_read()'
+    - drm/amd/display: Fix potential NULL pointer dereferences in
+      'dcn10_set_output_transfer_func()'
+    - perf evsel: Fix duplicate initialization of data->id in
+      evsel__parse_sample()
+    - clk: meson: Add missing clocks to axg_clk_regmaps
+    - media: em28xx: annotate unchecked call to media_device_register()
+    - media: v4l2-tpg: fix some memleaks in tpg_alloc
+    - media: v4l2-mem2mem: fix a memleak in v4l2_m2m_register_entity
+    - media: edia: dvbdev: fix a use-after-free
+    - pinctrl: mediatek: Drop bogus slew rate register range for MT8192
+    - clk: qcom: reset: Commonize the de/assert functions
+    - clk: qcom: reset: Ensure write completion on reset de/assertion
+    - quota: simplify drop_dquot_ref()
+    - quota: Fix potential NULL pointer dereference
+    - quota: Fix rcu annotations of inode dquot pointers
+    - PCI/P2PDMA: Fix a sleeping issue in a RCU read section
+    - PCI: switchtec: Fix an error handling path in switchtec_pci_probe()
+    - crypto: xilinx - call finalize with bh disabled
+    - perf thread_map: Free strlist on normal path in thread_map__new_by_tid_str()
+    - drm/radeon/ni: Fix wrong firmware size logging in ni_init_microcode()
+    - ALSA: seq: fix function cast warnings
+    - perf stat: Avoid metric-only segv
+    - ASoC: meson: Use dev_err_probe() helper
+    - ASoC: meson: aiu: fix function pointer type mismatch
+    - ASoC: meson: t9015: fix function pointer type mismatch
+    - powerpc: Force inlining of arch_vmap_p{u/m}d_supported()
+    - PCI: endpoint: Support NTB transfer between RC and EP
+    - [Config]: update CONFIG_PCI_EPF_VNTB
+    - NTB: EPF: fix possible memory leak in pci_vntb_probe()
+    - NTB: fix possible name leak in ntb_register_device()
+    - media: sun8i-di: Fix coefficient writes
+    - media: sun8i-di: Fix power on/off sequences
+    - media: sun8i-di: Fix chroma difference threshold
+    - media: imx: csc/scaler: fix v4l2_ctrl_handler memory leak
+    - media: go7007: add check of return value of go7007_read_addr()
+    - media: pvrusb2: remove redundant NULL check
+    - media: pvrusb2: fix pvr2_stream_callback casts
+    - clk: qcom: dispcc-sdm845: Adjust internal GDSC wait times
+    - drm/mediatek: dsi: Fix DSI RGB666 formats and definitions
+    - PCI: Mark 3ware-9650SE Root Port Extended Tags as broken
+    - clk: hisilicon: hi3519: Release the correct number of gates in
+      hi3519_clk_unregister()
+    - clk: hisilicon: hi3559a: Fix an erroneous devm_kfree()
+    - drm/tegra: put drm_gem_object ref on error in tegra_fb_create
+    - mfd: syscon: Call of_node_put() only when of_parse_phandle() takes a ref
+    - mfd: altera-sysmgr: Call of_node_put() only when of_parse_phandle() takes a
+      ref
+    - crypto: arm/sha - fix function cast warnings
+    - drm/tidss: Fix initial plane zpos values
+    - mtd: maps: physmap-core: fix flash size larger than 32-bit
+    - mtd: rawnand: lpc32xx_mlc: fix irq handler prototype
+    - ASoC: meson: axg-tdm-interface: fix mclk setup without mclk-fs
+    - ASoC: meson: axg-tdm-interface: add frame rate constraint
+    - HID: amd_sfh: Update HPD sensor structure elements
+    - drm/amdgpu: Fix missing break in ATOM_ARG_IMM Case of atom_get_src_int()
+    - media: pvrusb2: fix uaf in pvr2_context_set_notify
+    - media: dvb-frontends: avoid stack overflow warnings with clang
+    - media: go7007: fix a memleak in go7007_load_encoder
+    - media: ttpci: fix two memleaks in budget_av_attach
+    - media: mediatek: vcodec: avoid -Wcast-function-type-strict warning
+    - drm/mediatek: Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
+    - powerpc/hv-gpci: Fix the H_GET_PERF_COUNTER_INFO hcall return value checks
+    - drm/msm/dpu: add division of drm_display_mode's hskew parameter
+    - module: Add support for default value for module async_probe
+    - modules: wait do_free_init correctly
+    - powerpc/embedded6xx: Fix no previous prototype for avr_uart_send() etc.
+    - leds: aw2013: Unlock mutex before destroying it
+    - leds: sgm3140: Add missing timer cleanup and flash gpio control
+    - backlight: lm3630a: Initialize backlight_properties on init
+    - backlight: lm3630a: Don't set bl->props.brightness in get_brightness
+    - backlight: da9052: Fully initialize backlight_properties during probe
+    - backlight: lm3639: Fully initialize backlight_properties during probe
+    - backlight: lp8788: Fully initialize backlight_properties during probe
+    - sparc32: Fix section mismatch in leon_pci_grpci
+    - clk: Fix clk_core_get NULL dereference
+    - clk: zynq: Prevent null pointer dereference caused by kmalloc failure
+    - ALSA: hda/realtek: fix ALC285 issues on HP Envy x360 laptops
+    - ALSA: usb-audio: Stop parsing channels bits when all channels are found.
+    - RDMA/srpt: Do not register event handler until srpt device is fully setup
+    - f2fs: multidevice: support direct IO
+    - f2fs: invalidate META_MAPPING before IPU/DIO write
+    - f2fs: replace congestion_wait() calls with io_schedule_timeout()
+    - f2fs: fix to invalidate META_MAPPING before DIO write
+    - f2fs: invalidate meta pages only for post_read required inode
+    - f2fs: reduce stack memory cost by using bitfield in struct f2fs_io_info
+    - f2fs: compress: fix to cover normal cluster write with cp_rwsem
+    - f2fs: compress: fix to check unreleased compressed cluster
+    - scsi: csiostor: Avoid function pointer casts
+    - RDMA/device: Fix a race between mad_client and cm_client init
+    - RDMA/rtrs-clt: Check strnlen return len in sysfs mpath_policy_store()
+    - scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
+    - net: sunrpc: Fix an off by one in rpc_sockaddr2uaddr()
+    - NFSv4.2: fix nfs4_listxattr kernel BUG at mm/usercopy.c:102
+    - NFSv4.2: fix listxattr maximum XDR buffer size
+    - watchdog: stm32_iwdg: initialize default timeout
+    - NFS: Fix an off by one in root_nfs_cat()
+    - f2fs: compress: fix reserve_cblocks counting error when out of space
+    - afs: Revert "afs: Hide silly-rename files from userspace"
+    - comedi: comedi_test: Prevent timers rescheduling during deletion
+    - remoteproc: stm32: use correct format strings on 64-bit
+    - remoteproc: stm32: Fix incorrect type in assignment for va
+    - remoteproc: stm32: Fix incorrect type assignment returned by
+      stm32_rproc_get_loaded_rsc_tablef
+    - tty: vt: fix 20 vs 0x20 typo in EScsiignore
+    - serial: max310x: fix syntax error in IRQ error message
+    - tty: serial: samsung: fix tx_empty() to return TIOCSER_TEMT
+    - arm64: dts: broadcom: bcmbca: bcm4908: drop invalid switch cells
+    - kconfig: fix infinite loop when expanding a macro at the end of file
+    - rtc: mt6397: select IRQ_DOMAIN instead of depending on it
+    - serial: 8250_exar: Don't remove GPIO device on suspend
+    - staging: greybus: fix get_channel_from_mode() failure path
+    - usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
+    - io_uring: don't save/restore iowait state
+    - nouveau: reset the bo resource bus info after an eviction
+    - octeontx2-af: Use matching wake_up API variant in CGX command interface
+    - s390/vtime: fix average steal time calculation
+    - soc: fsl: dpio: fix kcalloc() argument order
+    - hsr: Fix uninit-value access in hsr_get_node()
+    - net: mtk_eth_soc: move MAC_MCR setting to mac_finish()
+    - net: mediatek: mtk_eth_soc: clear MAC_MCR_FORCE_LINK only when MAC is up
+    - net: ethernet: mtk_eth_soc: fix PPE hanging issue
+    - packet: annotate data-races around ignore_outgoing
+    - net: veth: do not manipulate GRO when using XDP
+    - net: dsa: mt7530: prevent possible incorrect XTAL frequency selection
+    - vdpa/mlx5: Allow CVQ size changes
+    - wireguard: receive: annotate data-race around receiving_counter.counter
+    - rds: introduce acquire/release ordering in acquire/release_in_xmit()
+    - hsr: Handle failures in module init
+    - net: phy: fix phy_read_poll_timeout argument type in genphy_loopback
+    - net/bnx2x: Prevent access to a freed page in page_pool
+    - octeontx2-af: Use separate handlers for interrupts
+    - netfilter: nf_tables: do not compare internal table flags on updates
+    - rcu: add a helper to report consolidated flavor QS
+    - net: report RCU QS on threaded NAPI repolling
+    - bpf: report RCU QS in cpumap kthread
+    - net: dsa: mt7530: fix handling of LLDP frames
+    - net: dsa: mt7530: fix handling of 802.1X PAE frames
+    - net: dsa: mt7530: fix link-local frames that ingress vlan filtering ports
+    - net: dsa: mt7530: fix handling of all link-local frames
+    - spi: spi-mt65xx: Fix NULL pointer access in interrupt handler
+    - regmap: Add missing map->bus check
+    - remoteproc: stm32: fix incorrect optional pointers
+  * Jammy update: v5.15.152 upstream stable release (LP: #2063276)
+    - mmc: mmci: stm32: use a buffer for unaligned DMA requests
+    - mmc: mmci: stm32: fix DMA API overlapping mappings warning
+    - net: lan78xx: fix runtime PM count underflow on link stop
+    - ixgbe: {dis, en}able irqs in ixgbe_txrx_ring_{dis, en}able
+    - i40e: disable NAPI right after disabling irqs when handling xsk_pool
+    - tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string
+    - geneve: make sure to pull inner header in geneve_rx()
+    - net: sparx5: Fix use after free inside sparx5_del_mact_entry
+    - net: ice: Fix potential NULL pointer dereference in ice_bridge_setlink()
+    - net/ipv6: avoid possible UAF in ip6_route_mpath_notify()
+    - cpumap: Zero-initialise xdp_rxq_info struct before running XDP program
+    - net/rds: fix WARNING in rds_conn_connect_if_down
+    - netfilter: nft_ct: fix l3num expectations with inet pseudo family
+    - netfilter: nf_conntrack_h323: Add protection for bmp length out of range
+    - erofs: apply proper VMA alignment for memory mapped files on THP
+    - netrom: Fix a data-race around sysctl_netrom_default_path_quality
+    - netrom: Fix a data-race around sysctl_netrom_obsolescence_count_initialiser
+    - netrom: Fix data-races around sysctl_netrom_network_ttl_initialiser
+    - netrom: Fix a data-race around sysctl_netrom_transport_timeout
+    - netrom: Fix a data-race around sysctl_netrom_transport_maximum_tries
+    - netrom: Fix a data-race around sysctl_netrom_transport_acknowledge_delay
+    - netrom: Fix a data-race around sysctl_netrom_transport_busy_delay
+    - netrom: Fix a data-race around sysctl_netrom_transport_requested_window_size
+    - netrom: Fix a data-race around sysctl_netrom_transport_no_activity_timeout
+    - netrom: Fix a data-race around sysctl_netrom_routing_control
+    - netrom: Fix a data-race around sysctl_netrom_link_fails_count
+    - netrom: Fix data-races around sysctl_net_busy_read
+    - ALSA: usb-audio: Refcount multiple accesses on the single clock
+    - ALSA: usb-audio: Clear fixed clock rate at closing EP
+    - ALSA: usb-audio: Split endpoint setups for hw_params and prepare (take#2)
+    - ALSA: usb-audio: Properly refcounting clock rate
+    - ALSA: usb-audio: Apply mutex around snd_usb_endpoint_set_params()
+    - ALSA: usb-audio: Correct the return code from snd_usb_endpoint_set_params()
+    - ALSA: usb-audio: Avoid superfluous endpoint setup
+    - ALSA: usb-audio: Add quirk for Tascam Model 12
+    - ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
+    - ALSA: usb-audio: Fix microphone sound on Nexigo webcam.
+    - ALSA: usb-audio: add quirk for RODE NT-USB+
+    - drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd()
+      & write_dpcd()' functions
+    - nfp: flower: add goto_chain_index for ct entry
+    - nfp: flower: add hardware offload check for post ct entry
+    - selftests/mm: switch to bash from sh
+    - selftests: mm: fix map_hugetlb failure on 64K page size systems
+    - xhci: process isoc TD properly when there was a transaction error mid TD.
+    - xhci: handle isoc Babble and Buffer Overrun events properly
+    - serial: max310x: use regmap methods for SPI batch operations
+    - serial: max310x: use a separate regmap for each port
+    - serial: max310x: prevent infinite while() loop in port startup
+    - drm/amd/pm: do not expose the API used internally only in kv_dpm.c
+    - drm/amdgpu: Reset IH OVERFLOW_CLEAR bit
+    - selftests: mptcp: decrease BW in simult flows
+    - hv_netvsc: use netif_is_bond_master() instead of open code
+    - hv_netvsc: Register VF in netvsc_probe if NET_DEVICE_REGISTER missed
+    - drm/amd/display: Re-arrange FPU code structure for dcn2x
+    - drm/amd/display: move calcs folder into DML
+    - drm/amd/display: remove DML Makefile duplicate lines
+    - drm/amd/display: Increase frame-larger-than for all display_mode_vba files
+    - getrusage: add the "signal_struct *sig" local variable
+    - getrusage: move thread_group_cputime_adjusted() outside of
+      lock_task_sighand()
+    - getrusage: use __for_each_thread()
+    - getrusage: use sig->stats_lock rather than lock_task_sighand()
+    - proc: Use task_is_running() for wchan in /proc/$pid/stat
+    - fs/proc: do_task_stat: move thread_group_cputime_adjusted() outside of
+      lock_task_sighand()
+    - ALSA: usb-audio: Fix wrong kfree issue in snd_usb_endpoint_free_all
+    - ALSA: usb-audio: Always initialize fixed_rate in
+      snd_usb_find_implicit_fb_sync_format()
+    - ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
+    - ALSA: usb-audio: Sort quirk table entries
+    - regmap: allow to define reg_update_bits for no bus configuration
+    - regmap: Add bulk read/write callbacks into regmap_config
+    - serial: max310x: make accessing revision id interface-agnostic
+    - serial: max310x: fix IO data corruption in batched operations
+    - Linux 5.15.152
+  * CVE-2024-26809
+    - netfilter: nft_set_pipapo: release elements in clone only from destroy path
+  * CVE-2024-26792
+    - btrfs: fix double free of anonymous device after snapshot creation failure
+  * CVE-2023-52530
+    - wifi: mac80211: fix potential key use-after-free
+  * CVE-2023-52447
+    - bpf: Defer the free of inner map when necessary
+    - rcu-tasks: Provide rcu_trace_implies_rcu_gp()
+  * Avoid creating non-working backlight sysfs knob from ASUS board
+    (LP: #2060422)
+    - platform/x86: asus-wmi: Consider device is absent when the read is ~0
+  * [Ubuntu 22.04.4/linux-image-6.5.0-26-generic] Kernel output "UBSAN: array-
+    index-out-of-bounds in /build/linux-hwe-6.5-34pCLi/linux-
+    hwe-6.5-6.5.0/drivers/net/hyperv/netvsc.c:1445:41" multiple times,
+    especially during boot. (LP: #2058477)
+    - hv: hyperv.h: Replace one-element array with flexible-array member
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209)
+    - netfilter: nf_tables: disallow timeout for anonymous sets
+    - mtd: spinand: gigadevice: Fix the get ecc status issue
+    - netlink: Fix kernel-infoleak-after-free in __skb_datagram_iter
+    - net: ip_tunnel: prevent perpetual headroom growth
+    - tun: Fix xdp_rxq_info's queue_index when detaching
+    - cpufreq: intel_pstate: fix pstate limits enforcement for adjust_perf call
+      back
+    - net: veth: clear GRO when clearing XDP even when down
+    - ipv6: fix potential "struct net" leak in inet6_rtm_getaddr()
+    - lan78xx: enable auto speed configuration for LAN7850 if no EEPROM is
+      detected
+    - net: enable memcg accounting for veth queues
+    - veth: try harder when allocating queue memory
+    - net: usb: dm9601: fix wrong return value in dm9601_mdio_read
+    - uapi: in6: replace temporary label with rfc9486
+    - stmmac: Clear variable when destroying workqueue
+    - Bluetooth: Avoid potential use-after-free in hci_error_reset
+    - Bluetooth: hci_event: Fix wrongly recorded wakeup BD_ADDR
+    - netfilter: nf_tables: allow NFPROTO_INET in nft_(match/target)_validate()
+    - netfilter: nfnetlink_queue: silence bogus compiler warning
+    - netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
+    - netfilter: make function op structures const
+    - netfilter: let reset rules clean out conntrack entries
+    - netfilter: bridge: confirm multicast packets before passing them up the
+      stack
+    - rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
+    - igb: extend PTP timestamp adjustments to i211
+    - efi/capsule-loader: fix incorrect allocation size
+    - power: supply: bq27xxx-i2c: Do not free non existing IRQ
+    - ALSA: Drop leftover snd-rtctimer stuff from Makefile
+    - fbcon: always restore the old font data in fbcon_do_set_font()
+    - afs: Fix endless loop in directory parsing
+    - riscv: Sparse-Memory/vmemmap out-of-bounds fix
+    - ALSA: firewire-lib: fix to check cycle continuity
+    - gtp: fix use-after-free and null-ptr-deref in gtp_newlink()
+    - wifi: nl80211: reject iftype change with mesh ID change
+    - btrfs: dev-replace: properly validate device names
+    - dmaengine: fsl-qdma: fix SoC may hang on 16 byte unaligned read
+    - dmaengine: ptdma: use consistent DMA masks
+    - dmaengine: fsl-qdma: init irq after reg initialization
+    - mmc: core: Fix eMMC initialization with 1-bit bus connection
+    - mmc: sdhci-xenon: add timeout for PHY init complete
+    - mmc: sdhci-xenon: fix PHY init clock stability
+    - pmdomain: qcom: rpmhpd: Fix enabled_corner aggregation
+    - x86/cpu/intel: Detect TME keyid bits before setting MTRR mask registers
+    - mptcp: move __mptcp_error_report in protocol.c
+    - mptcp: process pending subflow error on close
+    - mptcp: rename timer related helper to less confusing names
+    - selftests: mptcp: add missing kconfig for NF Filter
+    - selftests: mptcp: add missing kconfig for NF Filter in v6
+    - mptcp: clean up harmless false expressions
+    - mptcp: add needs_id for netlink appending addr
+    - mptcp: push at DSS boundaries
+    - mptcp: fix possible deadlock in subflow diag
+    - cachefiles: fix memory leak in cachefiles_add_cache()
+    - fs,hugetlb: fix NULL pointer dereference in hugetlbs_fill_super
+    - Revert "drm/bridge: lt8912b: Register and attach our DSI device at probe"
+    - af_unix: Drop oob_skb ref before purging queue in GC.
+    - gpio: 74x164: Enable output pins after registers are reset
+    - gpiolib: Fix the error path order in gpiochip_add_data_with_key()
+    - gpio: fix resource unwinding order in error path
+    - Revert "interconnect: Fix locking for runpm vs reclaim"
+    - Revert "interconnect: Teach lockdep about icc_bw_lock order"
+    - bpf: Add BPF_FIB_LOOKUP_SKIP_NEIGH for bpf_fib_lookup
+    - bpf: Add table ID to bpf_fib_lookup BPF helper
+    - bpf: Derive source IP addr via bpf_*_fib_lookup()
+    - Linux 5.15.151
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209) //
+    CVE-2024-26782
+    - mptcp: fix double-free on socket dismantle
+  * Jammy update: v5.15.151 upstream stable release (LP: #2060209) // Fix
+    bluetooth connections with 3.0 device (LP: #2063067)
+    - Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142)
+    - net/sched: Retire CBQ qdisc
+    - [Config] updateconfigs for NET_SCH_CBQ
+    - net/sched: Retire ATM qdisc
+    - [Config] updateconfigs for NET_SCH_ATM
+    - net/sched: Retire dsmark qdisc
+    - [Config] updateconfigs for NET_SCH_DSMARK
+    - smb: client: fix potential OOBs in smb2_parse_contexts()
+    - smb: client: fix parsing of SMB3.1.1 POSIX create context
+    - sched/rt: sysctl_sched_rr_timeslice show default timeslice after reset
+    - PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
+    - bpf: Merge printk and seq_printf VARARG max macros
+    - bpf: Add struct for bin_args arg in bpf_bprintf_prepare
+    - bpf: Do cleanup in bpf_bprintf_cleanup only when needed
+    - bpf: Remove trace_printk_lock
+    - userfaultfd: fix mmap_changing checking in mfill_atomic_hugetlb
+    - zonefs: Improve error handling
+    - x86/fpu: Stop relying on userspace for info to fault in xsave buffer
+    - sched/rt: Fix sysctl_sched_rr_timeslice intial value
+    - sched/rt: Disallow writing invalid values to sched_rt_period_us
+    - scsi: target: core: Add TMF to tmr_list handling
+    - dmaengine: shdma: increase size of 'dev_id'
+    - dmaengine: fsl-qdma: increase size of 'irq_name'
+    - wifi: cfg80211: fix missing interfaces when dumping
+    - wifi: mac80211: fix race condition on enabling fast-xmit
+    - fbdev: savage: Error out if pixclock equals zero
+    - fbdev: sis: Error out if pixclock equals zero
+    - spi: hisi-sfc-v3xx: Return IRQ_NONE if no interrupts were detected
+    - ahci: asm1166: correct count of reported ports
+    - ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers
+    - MIPS: reserve exception vector space ONLY ONCE
+    - platform/x86: touchscreen_dmi: Add info for the TECLAST X16 Plus tablet
+    - ext4: avoid dividing by 0 in mb_update_avg_fragment_size() when block bitmap
+      corrupt
+    - ext4: avoid allocating blocks from corrupted group in
+      ext4_mb_try_best_found()
+    - ext4: avoid allocating blocks from corrupted group in ext4_mb_find_by_goal()
+    - dmaengine: ti: edma: Add some null pointer checks to the edma_probe
+    - regulator: pwm-regulator: Add validity checks in continuous .get_voltage
+    - nvmet-tcp: fix nvme tcp ida memory leak
+    - ALSA: usb-audio: Check presence of valid altsetting control
+    - ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616
+    - spi: sh-msiof: avoid integer overflow in constants
+    - Input: xpad - add Lenovo Legion Go controllers
+    - netfilter: conntrack: check SCTP_CID_SHUTDOWN_ACK for vtag setting in
+      sctp_new
+    - ALSA: usb-audio: Ignore clock selector errors for single connection
+    - nvme-fc: do not wait in vain when unloading module
+    - nvmet-fcloop: swap the list_add_tail arguments
+    - nvmet-fc: release reference on target port
+    - nvmet-fc: defer cleanup using RCU properly
+    - nvmet-fc: hold reference on hostport match
+    - nvmet-fc: abort command when there is no binding
+    - nvmet-fc: avoid deadlock on delete association path
+    - nvmet-fc: take ref count on tgtport before delete assoc
+    - ext4: correct the hole length returned by ext4_map_blocks()
+    - Input: i8042 - add Fujitsu Lifebook U728 to i8042 quirk table
+    - fs/ntfs3: Modified fix directory element type detection
+    - fs/ntfs3: Improve ntfs_dir_count
+    - fs/ntfs3: Correct hard links updating when dealing with DOS names
+    - fs/ntfs3: Print warning while fixing hard links count
+    - fs/ntfs3: Fix detected field-spanning write (size 8) of single field
+      "le->name"
+    - fs/ntfs3: Add NULL ptr dereference checking at the end of
+      attr_allocate_frame()
+    - fs/ntfs3: Disable ATTR_LIST_ENTRY size check
+    - fs/ntfs3: use non-movable memory for ntfs3 MFT buffer cache
+    - fs/ntfs3: Prevent generic message "attempt to access beyond end of device"
+    - fs/ntfs3: Correct function is_rst_area_valid
+    - fs/ntfs3: Update inode->i_size after success write into compressed file
+    - fs/ntfs3: Fix oob in ntfs_listxattr
+    - wifi: mac80211: adding missing drv_mgd_complete_tx() call
+    - efi: runtime: Fix potential overflow of soft-reserved region size
+    - efi: Don't add memblocks for soft-reserved memory
+    - hwmon: (coretemp) Enlarge per package core count limit
+    - scsi: lpfc: Use unsigned type for num_sge
+    - firewire: core: send bus reset promptly on gap count error
+    - drm/amdgpu: skip to program GFXDEC registers for suspend abort
+    - drm/amdgpu: reset gpu for s3 suspend abort case
+    - virtio-blk: Ensure no requests in virtqueues before deleting vqs.
+    - pmdomain: mediatek: fix race conditions with genpd
+    - ksmbd: free aux buffer if ksmbd_iov_pin_rsp_read fails
+    - pmdomain: renesas: r8a77980-sysc: CR7 must be always on
+    - erofs: fix lz4 inplace decompression
+    - IB/hfi1: Fix sdma.h tx->num_descs off-by-one error
+    - drm/ttm: Fix an invalid freeing on already freed page in error path
+    - dm-crypt: don't modify the data when using authenticated encryption
+    - platform/x86: intel-vbtn: Stop calling "VBDL" from notify_handler
+    - platform/x86: touchscreen_dmi: Allow partial (prefix) matches for ACPI names
+    - KVM: arm64: vgic-its: Test for valid IRQ in MOVALL handler
+    - KVM: arm64: vgic-its: Test for valid IRQ in its_sync_lpi_pending_table()
+    - gtp: fix use-after-free and null-ptr-deref in gtp_genl_dump_pdp()
+    - PCI/MSI: Prevent MSI hardware interrupt number truncation
+    - l2tp: pass correct message length to ip6_append_data
+    - ARM: ep93xx: Add terminator to gpiod_lookup_table
+    - Revert "x86/ftrace: Use alternative RET encoding"
+    - x86/text-patching: Make text_gen_insn() play nice with ANNOTATE_NOENDBR
+    - x86/ibt,paravirt: Use text_gen_insn() for paravirt_patch()
+    - x86/ftrace: Use alternative RET encoding
+    - x86/returnthunk: Allow different return thunks
+    - Revert "x86/alternative: Make custom return thunk unconditional"
+    - x86/alternative: Make custom return thunk unconditional
+    - serial: amba-pl011: Fix DMA transmission in RS485 mode
+    - usb: dwc3: gadget: Don't disconnect if not started
+    - usb: cdnsp: blocked some cdns3 specific code
+    - usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
+    - usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
+    - usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
+    - usb: roles: fix NULL pointer issue when put module's reference
+    - usb: roles: don't get/set_role() when usb_role_switch is unregistered
+    - mptcp: fix lockless access in subflow ULP diag
+    - clk: imx: imx8mp: add shared clk gate for usb suspend clk
+    - clk: qcom: gcc-qcs404: disable gpll[04]_out_aux parents
+    - clk: qcom: gcc-qcs404: fix names of the DSI clocks used as parents
+    - mtd: rawnand: sunxi: Fix the size of the last OOB region
+    - RISC-V: fix funct4 definition for c.jalr in parse_asm.h
+    - Input: iqs269a - drop unused device node references
+    - Input: iqs269a - configure device with a single block write
+    - Input: iqs269a - increase interrupt handler return delay
+    - clk: renesas: cpg-mssr: Fix use after free if cpg_mssr_common_init() failed
+    - Input: ads7846 - don't report pressure for ads7845
+    - clk: renesas: cpg-mssr: Remove superfluous check in resume code
+    - clk: imx: avoid memory leak
+    - Input: ads7846 - always set last command to PWRDOWN
+    - Input: ads7846 - don't check penirq immediately for 7845
+    - powerpc/powernv/ioda: Skip unallocated resources when mapping to PE
+    - clk: qcom: gpucc-sc7180: fix clk_dis_wait being programmed for CX GDSC
+    - clk: qcom: gpucc-sdm845: fix clk_dis_wait being programmed for CX GDSC
+    - clk: Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
+    - powerpc/pseries/lparcfg: add missing RTAS retry status handling
+    - powerpc/perf/hv-24x7: add missing RTAS retry status handling
+    - powerpc/pseries/lpar: add missing RTAS retry status handling
+    - MIPS: SMP-CPS: fix build error when HOTPLUG_CPU not set
+    - MIPS: vpe-mt: drop physical_memsize
+    - vdpa/mlx5: Don't clear mr struct on destroy MR
+    - ARM: dts: BCM53573: Drop nonexistent #usb-cells
+    - RDMA/siw: Balance the reference of cep->kref in the error path
+    - RDMA/siw: Correct wrong debug message
+    - clk: linux/clk-provider.h: fix kernel-doc warnings and typos
+    - platform/x86: asus-wmi: Document the dgpu_disable sysfs attribute
+    - acpi: property: Let args be NULL in __acpi_node_get_property_reference
+    - ARM: dts: BCM53573: Drop nonexistent "default-off" LED trigger
+    - tools headers UAPI: Sync linux/fscrypt.h with the kernel sources
+    - perf beauty: Update copy of linux/socket.h with the kernel sources
+    - tools/virtio: fix build
+    - drm/amdgpu: init iommu after amdkfd device init
+    - f2fs: don't set GC_FAILURE_PIN for background GC
+    - f2fs: write checkpoint during FG_GC
+    - drm/i915/dg1: Update DMC_DEBUG3 register
+    - kernel/sched: Remove dl_boosted flag comment
+    - cifs: remove useless parameter 'is_fsctl' from SMB2_ioctl()
+    - serial: 8250: Remove serial_rs485 sanitization from em485
+    - clk: imx8mp: Add DISP2 pixel clock
+    - clk: imx8mp: add clkout1/2 support
+    - dt-bindings: clocks: imx8mp: Add ID for usb suspend clock
+    - net: ethernet: ti: add missing of_node_put before return
+    - powerpc/rtas: make all exports GPL
+    - powerpc/rtas: ensure 4KB alignment for rtas_data_buf
+    - powerpc/eeh: Small refactor of eeh_handle_normal_event()
+    - powerpc/eeh: Set channel state after notifying the drivers
+    - PM: core: Redefine pm_ptr() macro
+    - PM: core: Add new *_PM_OPS macros, deprecate old ones
+    - mmc: jz4740: Use the new PM macros
+    - mmc: mxc: Use the new PM macros
+    - PM: core: Remove static qualifier in DEFINE_SIMPLE_DEV_PM_OPS macro
+    - Input: iqs269a - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
+    - Input: iqs269a - do not poll during suspend or resume
+    - Input: iqs269a - do not poll during ATI
+    - net/sched: Refactor qdisc_graft() for ingress and clsact Qdiscs
+    - netfilter: nf_tables: add rescheduling points during loop detection walks
+    - debugobjects: Recheck debug_objects_enabled before reporting
+    - nbd: Add the maximum limit of allocated index in nbd_dev_add
+    - md: fix data corruption for raid456 when reshape restart while grow up
+    - md/raid10: prevent soft lockup while flush writes
+    - posix-timers: Ensure timer ID search-loop limit is valid
+    - btrfs: add xxhash to fast checksum implementations
+    - ACPI: button: Add lid disable DMI quirk for Nextbook Ares 8A
+    - ACPI: video: Add backlight=native DMI quirk for Apple iMac11,3
+    - ACPI: video: Add backlight=native DMI quirk for Lenovo ThinkPad X131e (3371
+      AMD version)
+    - arm64: set __exception_irq_entry with __irq_entry as a default
+    - arm64: mm: fix VA-range sanity check
+    - sched/fair: Don't balance task to its current running CPU
+    - wifi: ath11k: fix registration of 6Ghz-only phy without the full channel
+      range
+    - bpf: Address KCSAN report on bpf_lru_list
+    - devlink: report devlink_port_type_warn source device
+    - wifi: wext-core: Fix -Wstringop-overflow warning in
+      ioctl_standard_iw_point()
+    - wifi: iwlwifi: mvm: avoid baid size integer overflow
+    - exfat: support dynamic allocate bh for exfat_entry_set_cache
+    - arm64: dts: rockchip: fix regulator name on rk3399-rock-4
+    - arm64: dts: rockchip: add ES8316 codec for ROCK Pi 4
+    - arm64: dts: rockchip: add SPDIF node for ROCK Pi 4
+    - ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
+    - ACPI: video: Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
+    - ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA
+    - ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
+    - ACPI: resource: Skip IRQ override on Asus Expertbook B2402CBA
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1502CBA
+    - xhci: cleanup xhci_hub_control port references
+    - xhci: move port specific items such as state completions to port structure
+    - xhci: rename resume_done to resume_timestamp
+    - xhci: clear usb2 resume related variables in one place.
+    - xhci: decouple usb2 port resume and get_port_status request handling
+    - xhci: track port suspend state correctly in unsuccessful resume cases
+    - cifs: add a warning when the in-flight count goes negative
+    - IB/hfi1: Fix a memleak in init_credit_return
+    - RDMA/bnxt_re: Return error for SRQ resize
+    - RDMA/irdma: Fix KASAN issue with tasklet
+    - RDMA/irdma: Validate max_send_wr and max_recv_wr
+    - RDMA/irdma: Set the CQ read threshold for GEN 1
+    - RDMA/irdma: Add AE for too many RNRS
+    - RDMA/srpt: Support specifying the srpt_service_guid parameter
+    - RDMA/qedr: Fix qedr_create_user_qp error flow
+    - arm64: dts: rockchip: set num-cs property for spi on px30
+    - RDMA/srpt: fix function pointer cast warnings
+    - bpf, scripts: Correct GPL license name
+    - scsi: jazz_esp: Only build if SCSI core is builtin
+    - nouveau: fix function cast warnings
+    - net: stmmac: Fix incorrect dereference in interrupt handlers
+    - ipv4: properly combine dev_base_seq and ipv4.dev_addr_genid
+    - ipv6: properly combine dev_base_seq and ipv6.dev_addr_genid
+    - ata: libahci_platform: Convert to using devm bulk clocks API
+    - ata: libahci_platform: Introduce reset assertion/deassertion methods
+    - ata: ahci_ceva: fix error handling for Xilinx GT PHY support
+    - bpf: Fix racing between bpf_timer_cancel_and_free and bpf_timer_cancel
+    - drm/nouveau/instmem: fix uninitialized_var.cocci warning
+    - octeontx2-af: Consider the action set by PF
+    - s390: use the correct count for __iowrite64_copy()
+    - netfilter: nf_tables: set dormant flag on hook register failure
+    - netfilter: flowtable: simplify route logic
+    - netfilter: nft_flow_offload: reset dst in route object after setting up flow
+    - netfilter: nft_flow_offload: release dst in case direct xmit path is used
+    - drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set
+    - drm/amd/display: Fix memory leak in dm_sw_fini()
+    - i2c: imx: Add timer for handling the stop condition
+    - i2c: imx: when being a target, mark the last read as processed
+    - fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio
+    - netfilter: nf_tables: fix scheduling-while-atomic splat
+    - ext4: regenerate buddy after block freeing failed if under fc replay
+    - ext4: avoid bb_free and bb_fragments inconsistency in mb_free_blocks()
+    - netfilter: nf_tables: can't schedule in nft_chain_validate
+    - r8169: use new PM macros
+    - Linux 5.15.150
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26733
+    - packet: move from strlcpy with unused retval to strscpy
+    - net: dev: Convert sa_data to flexible array in struct sockaddr
+    - arp: Prevent overflow in arp_req_get().
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26735
+    - ipv6: sr: fix possible use-after-free and null-ptr-deref
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26736
+    - afs: Increase buffer size in afs_update_volume_status()
+  * Jammy update: v5.15.150 upstream stable release (LP: #2060142) //
+    CVE-2024-26748
+    - usb: cdns3: fix memory double free when handle zero packet
+  * CVE-2023-47233
+    - wifi: brcmfmac: Fix use-after-free bug in brcmf_cfg80211_detach
+  * CVE-2024-26584
+    - net: tls: handle backlogging of crypto requests
+  * CVE-2024-26585
+    - tls: fix race between tx work scheduling and socket close
+  * CVE-2024-26583
+    - tls: rx: jump to a more appropriate label
+    - tls: rx: drop pointless else after goto
+    - tls: stop recv() if initial process_rx_list gave us non-DATA
+    - tls: rx: don't store the record type in socket context
+    - tls: rx: don't store the decryption status in socket context
+    - tls: rx: don't issue wake ups when data is decrypted
+    - tls: rx: refactor decrypt_skb_update()
+    - tls: hw: rx: use return value of tls_device_decrypted() to carry status
+    - tls: rx: drop unnecessary arguments from tls_setup_from_iter()
+    - tls: rx: don't report text length from the bowels of decrypt
+    - tls: rx: wrap decryption arguments in a structure
+    - tls: rx: factor out writing ContentType to cmsg
+    - tls: rx: don't track the async count
+    - tls: rx: move counting TlsDecryptErrors for sync
+    - tls: rx: assume crypto always calls our callback
+    - tls: rx: use async as an in-out argument
+    - tls: decrement decrypt_pending if no async completion will be called
+    - net: tls: fix async vs NIC crypto offload
+    - Revert "tls: rx: move counting TlsDecryptErrors for sync"
+    - tls: rx: simplify async wait
+    - tls: rx: return the already-copied data on crypto error
+    - tls: rx: allow only one reader at a time
+    - tls: rx: release the sock lock on locking timeout
+    - tls: extract context alloc/initialization out of tls_set_sw_offload
+    - net: tls: factor out tls_*crypt_async_wait()
+    - tls: fix race between async notify and socket close
+  * CVE-2024-26622
+    - tomoyo: fix UAF write bug in tomoyo_write_control()
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Mon, 27 May 2024 17:29:36 +1000
+
+linux-xilinx-zynqmp (5.15.0-1029.33) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1029.33 -proposed tracker (LP: #2061809)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop getabis data
+    - [Packaging] drop ABI data
+    - [Packaging] debian.zynqmp/dkms-versions -- update from kernel-versions
+      (main/2024.04.01)
+
+  * Jammy update: v5.15.148 upstream stable release (LP: #2055145)
+    - [Config] update annotations for CONFIG_MMC_SDHCI_AM654
+
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014)
+    - [Config] updateconfigs for MFD_TI_AM335X_TSCADC
+
+  *  Backport AXI 1-wire host driver (LP: #2058707)
+    - dt-bindings: w1: Add AMD AXI w1 host and MAINTAINERS entry
+    - w1: Add AXI 1-wire host driver for AMD programmable logic IP core
+    - w1: amd_axi_w1: Explicitly include correct DT includes
+    - [Config] Enable CONFIG_W1_MASTER_AMD_AXI
+
+  * Unsupported platform 'ZynqMP KV260 revB (LP: #2058321)
+    - [Packaging] Add breaks on flash-kernel older than 3.104ubuntu20
+
+  * Update on-chip oscillator clock nodes for Kria (LP: #2055241)
+    - arm64: zynqmp: Sync clock labels with kr260 revB
+    - arm64: zynqmp: Describe 25MHz fixed clock for PL GEMs
+    - arm64: zynqmp: Fix kr260 clock wiring
+
+  [ Ubuntu: 5.15.0-106.116 ]
+
+  * jammy/linux: 5.15.0-106.116 -proposed tracker (LP: #2061812)
+  * CVE-2024-2201
+    - x86/bugs: Use sysfs_emit()
+    - KVM: x86: Update KVM-only leaf handling to allow for 100% KVM-only leafs
+    - KVM: x86: Advertise CPUID.(EAX=7,ECX=2):EDX[5:0] to userspace
+    - KVM: x86: Use a switch statement and macros in __feature_translate()
+    - x86/bugs: Change commas to semicolons in 'spectre_v2' sysfs file
+    - x86/syscall: Don't force use of indirect calls for system calls
+    - x86/bhi: Add support for clearing branch history at syscall entry
+    - x86/bhi: Define SPEC_CTRL_BHI_DIS_S
+    - x86/bhi: Enumerate Branch History Injection (BHI) bug
+    - x86/bhi: Add BHI mitigation knob
+    - x86/bhi: Mitigate KVM by default
+    - KVM: x86: Add BHI_NO
+    - [Config] Set CONFIG_BHI to enabled (auto)
+  * Drop fips-checks script from trees (LP: #2055083)
+    - [Packaging] Remove fips-checks script
+  * alsa/realtek: adjust max output valume for headphone on 2 LG machines
+    (LP: #2058573)
+    - ALSA: hda/realtek: fix the hp playback volume issue for LG machines
+  * A general-proteciton exception during guest migration to unsupported PKRU
+    machine (LP: #2032164)
+    - x86/fpu: Allow caller to constrain xfeatures when copying to uabi buffer
+    - KVM: x86: Constrain guest-supported xfeatures only at KVM_GET_XSAVE{2}
+  *  [ICX] [SPR] [ipc/msg] performance: Mitigate the lock contention with percpu
+    counter (LP: #2058485)
+    - ipc: check checkpoint_restore_ns_capable() to modify C/R proc files
+    - ipc/ipc_sysctl.c: remove fallback for !CONFIG_PROC_SYSCTL
+    - ipc: Store mqueue sysctls in the ipc namespace
+    - ipc: Store ipc sysctls in the ipc namespace
+    - ipc: Use the same namespace to modify and validate
+    - ipc: Remove extra1 field abuse to pass ipc namespace
+    - ipc: Check permissions for checkpoint_restart sysctls at open time
+    - percpu: add percpu_counter_add_local and percpu_counter_sub_local
+    - ipc/msg: mitigate the lock contention with percpu counter
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014)
+    - ksmbd: free ppace array on error in parse_dacl
+    - ksmbd: don't allow O_TRUNC open on read-only share
+    - ksmbd: validate mech token in session setup
+    - ksmbd: fix UAF issue in ksmbd_tcp_new_connection()
+    - ksmbd: only v2 leases handle the directory
+    - iio: adc: ad7091r: Set alert bit in config register
+    - iio: adc: ad7091r: Allow users to configure device events
+    - iio: adc: ad7091r: Enable internal vref if external vref is not supplied
+    - dmaengine: fix NULL pointer in channel unregistration function
+    - scsi: ufs: core: Simplify power management during async scan
+    - scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
+    - iio:adc:ad7091r: Move exports into IIO_AD7091R namespace.
+    - ext4: allow for the last group to be marked as trimmed
+    - btrfs: sysfs: validate scrub_speed_max value
+    - crypto: api - Disallow identical driver names
+    - PM: hibernate: Enforce ordering during image compression/decompression
+    - hwrng: core - Fix page fault dead lock on mmap-ed hwrng
+    - crypto: s390/aes - Fix buffer overread in CTR mode
+    - media: imx355: Enable runtime PM before registering async sub-device
+    - rpmsg: virtio: Free driver_override when rpmsg_remove()
+    - media: ov9734: Enable runtime PM before registering async sub-device
+    - mips: Fix max_mapnr being uninitialized on early stages
+    - bus: mhi: host: Drop chan lock before queuing buffers
+    - bus: mhi: host: Add spinlock to protect WP access when queueing TREs
+    - parisc/firmware: Fix F-extend for PDC addresses
+    - async: Split async_schedule_node_domain()
+    - async: Introduce async_schedule_dev_nocall()
+    - arm64: dts: qcom: sc7180: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sdm845: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sm8150: fix USB wakeup interrupt types
+    - arm64: dts: qcom: sdm845: fix USB DP/DM HS PHY interrupts
+    - lsm: new security_file_ioctl_compat() hook
+    - scripts/get_abi: fix source path leak
+    - mmc: core: Use mrq.sbc in close-ended ffu
+    - mmc: mmc_spi: remove custom DMA mapped buffers
+    - rtc: Adjust failure return code for cmos_set_alarm()
+    - nouveau/vmm: don't set addr on the fail path to avoid warning
+    - ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path
+    - rename(): fix the locking of subdirectories
+    - ksmbd: set v2 lease version on lease upgrade
+    - ksmbd: fix potential circular locking issue in smb2_set_ea()
+    - ksmbd: don't increment epoch if current state and request state are same
+    - ksmbd: send lease break notification on FILE_RENAME_INFORMATION
+    - ksmbd: Add missing set_freezable() for freezable kthread
+    - net/smc: fix illegal rmb_desc access in SMC-D connection dump
+    - tcp: make sure init the accept_queue's spinlocks once
+    - bnxt_en: Wait for FLR to complete during probe
+    - vlan: skip nested type that is not IFLA_VLAN_QOS_MAPPING
+    - llc: make llc_ui_sendmsg() more robust against bonding changes
+    - llc: Drop support for ETH_P_TR_802_2.
+    - net/rds: Fix UBSAN: array-index-out-of-bounds in rds_cmsg_recv
+    - tracing: Ensure visibility when inserting an element into tracing_map
+    - afs: Hide silly-rename files from userspace
+    - tcp: Add memory barrier to tcp_push()
+    - netlink: fix potential sleeping issue in mqueue_flush_file
+    - ipv6: init the accept_queue's spinlocks in inet6_create
+    - net/mlx5: DR, Use the right GVMI number for drop action
+    - net/mlx5: DR, Align mlx5dv_dr API vport action with FW behavior
+    - net/mlx5: DR, Can't go to uplink vport on RX rule
+    - net/mlx5e: fix a double-free in arfs_create_groups
+    - net/mlx5e: fix a potential double-free in fs_any_create_groups
+    - overflow: Allow mixed type arguments
+    - netfilter: nft_limit: reject configurations that cause integer overflow
+    - netfilter: nf_tables: restrict anonymous set and map names to 16 bytes
+    - netfilter: nf_tables: validate NFPROTO_* family
+    - net: stmmac: Wait a bit for the reset to take effect
+    - net: mvpp2: clear BM pool before initialization
+    - selftests: netdevsim: fix the udp_tunnel_nic test
+    - fjes: fix memleaks in fjes_hw_setup
+    - net: fec: fix the unhandled context fault from smmu
+    - btrfs: fix infinite directory reads
+    - btrfs: set last dir index to the current last index when opening dir
+    - btrfs: refresh dir last index during a rewinddir(3) call
+    - btrfs: fix race between reading a directory and adding entries to it
+    - btrfs: avoid copying BTRFS_ROOT_SUBVOL_DEAD flag to snapshot of subvolume
+      being deleted
+    - btrfs: ref-verify: free ref cache before clearing mount opt
+    - btrfs: tree-checker: fix inline ref size in error messages
+    - btrfs: don't warn if discard range is not aligned to sector
+    - btrfs: defrag: reject unknown flags of btrfs_ioctl_defrag_range_args
+    - btrfs: don't abort filesystem when attempting to snapshot deleted subvolume
+    - rbd: don't move requests to the running list on errors
+    - exec: Fix error handling in begin_new_exec()
+    - wifi: iwlwifi: fix a memory corruption
+    - hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes
+    - netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress
+      basechain
+    - firmware: arm_scmi: Check mailbox/SMT channel for consistency
+    - xfs: read only mounts with fsopen mount API are busted
+    - gpiolib: acpi: Ignore touchpad wakeup on GPD G1619-04
+    - drm: Don't unref the same fb many times by mistake due to deadlock handling
+    - drm/bridge: nxp-ptn3460: fix i2c_master_send() error checking
+    - drm/tidss: Fix atomic_flush check
+    - drm/bridge: nxp-ptn3460: simplify some error checking
+    - PM: core: Remove unnecessary (void *) conversions
+    - PM: sleep: Fix possible deadlocks in core system-wide PM code
+    - bus: mhi: host: Rename "struct mhi_tre" to "struct mhi_ring_element"
+    - bus: mhi: host: Add alignment check for event ring read pointer
+    - fs/pipe: move check to pipe_has_watch_queue()
+    - pipe: wakeup wr_wait after setting max_usage
+    - ARM: dts: qcom: sdx55: fix USB wakeup interrupt types
+    - ARM: dts: samsung: exynos4210-i9100: Unconditionally enable LDO12
+    - ARM: dts: qcom: sdx55: fix pdc '#interrupt-cells'
+    - ARM: dts: qcom: sdx55: fix USB DP/DM HS PHY interrupts
+    - ARM: dts: qcom: sdx55: fix USB SS wakeup
+    - media: mtk-jpeg: Fix use after free bug due to error path handling in
+      mtk_jpeg_dec_device_run
+    - mm: use __pfn_to_section() instead of open coding it
+    - mm/sparsemem: fix race in accessing memory_section->usage
+    - PM / devfreq: Fix buffer overflow in trans_stat_show
+    - btrfs: add definition for EXTENT_TREE_V2
+    - ksmbd: fix global oob in ksmbd_nl_policy
+    - cpufreq: intel_pstate: Drop redundant intel_pstate_get_hwp_cap() call
+    - cpufreq: intel_pstate: Refine computation of P-state for given frequency
+    - drm: panel-simple: add missing bus flags for Tianma tm070jvhg[30/33]
+    - drm/exynos: fix accidental on-stack copy of exynos_drm_plane
+    - drm/exynos: gsc: minor fix for loop iteration in gsc_runtime_resume
+    - gpio: eic-sprd: Clear interrupt after set the interrupt type
+    - spi: bcm-qspi: fix SFDP BFPT read by usig mspi read
+    - mips: Call lose_fpu(0) before initializing fcr31 in mips_set_personality_nan
+    - tick/sched: Preserve number of idle sleeps across CPU hotplug events
+    - x86/entry/ia32: Ensure s32 is sign extended to s64
+    - powerpc/mm: Fix null-pointer dereference in pgtable_cache_add
+    - arm64: irq: set the correct node for VMAP stack
+    - drivers/perf: pmuv3: don't expose SW_INCR event in sysfs
+    - powerpc: Fix build error due to is_valid_bugaddr()
+    - powerpc/mm: Fix build failures due to arch_reserved_kernel_pages()
+    - powerpc/64s: Fix CONFIG_NUMA=n build due to create_section_mapping()
+    - x86/boot: Ignore NMIs during very early boot
+    - powerpc: pmd_move_must_withdraw() is only needed for
+      CONFIG_TRANSPARENT_HUGEPAGE
+    - powerpc/lib: Validate size for vector operations
+    - x86/mce: Mark fatal MCE's page as poison to avoid panic in the kdump kernel
+    - perf/core: Fix narrow startup race when creating the perf nr_addr_filters
+      sysfs file
+    - debugobjects: Stop accessing objects after releasing hash bucket lock
+    - regulator: core: Only increment use_count when enable_count changes
+    - audit: Send netlink ACK before setting connection in auditd_set
+    - ACPI: video: Add quirk for the Colorful X15 AT 23 Laptop
+    - PNP: ACPI: fix fortify warning
+    - ACPI: extlog: fix NULL pointer dereference check
+    - PM / devfreq: Synchronize devfreq_monitor_[start/stop]
+    - ACPI: APEI: set memory failure flags as MF_ACTION_REQUIRED on synchronous
+      events
+    - FS:JFS:UBSAN:array-index-out-of-bounds in dbAdjTree
+    - jfs: fix slab-out-of-bounds Read in dtSearch
+    - jfs: fix array-index-out-of-bounds in dbAdjTree
+    - pstore/ram: Fix crash when setting number of cpus to an odd number
+    - crypto: octeontx2 - Fix cptvf driver cleanup
+    - crypto: stm32/crc32 - fix parsing list of devices
+    - afs: fix the usage of read_seqbegin_or_lock() in afs_lookup_volume_rcu()
+    - afs: fix the usage of read_seqbegin_or_lock() in afs_find_server*()
+    - rxrpc_find_service_conn_rcu: fix the usage of read_seqbegin_or_lock()
+    - jfs: fix array-index-out-of-bounds in diNewExt
+    - arch: consolidate arch_irq_work_raise prototypes
+    - s390/ptrace: handle setting of fpc register correctly
+    - KVM: s390: fix setting of fpc register
+    - SUNRPC: Fix a suspicious RCU usage warning
+    - ecryptfs: Reject casefold directory inodes
+    - ext4: fix inconsistent between segment fstrim and full fstrim
+    - ext4: unify the type of flexbg_size to unsigned int
+    - ext4: remove unnecessary check from alloc_flex_gd()
+    - ext4: avoid online resizing failures due to oversized flex bg
+    - wifi: rt2x00: restart beacon queue when hardware reset
+    - selftests/bpf: satisfy compiler by having explicit return in btf test
+    - selftests/bpf: Fix pyperf180 compilation failure with clang18
+    - selftests/bpf: Fix issues in setup_classid_environment()
+    - scsi: lpfc: Fix possible file string name overflow when updating firmware
+    - PCI: Add no PM reset quirk for NVIDIA Spectrum devices
+    - bonding: return -ENOMEM instead of BUG in alb_upper_dev_walk
+    - scsi: arcmsr: Support new PCI device IDs 1883 and 1886
+    - ARM: dts: imx7d: Fix coresight funnel ports
+    - ARM: dts: imx7s: Fix lcdif compatible
+    - ARM: dts: imx7s: Fix nand-controller #size-cells
+    - wifi: ath9k: Fix potential array-index-out-of-bounds read in
+      ath9k_htc_txstatus()
+    - bpf: Add map and need_defer parameters to .map_fd_put_ptr()
+    - scsi: libfc: Don't schedule abort twice
+    - scsi: libfc: Fix up timeout error in fc_fcp_rec_error()
+    - bpf: Set uattr->batch.count as zero before batched update or deletion
+    - ARM: dts: rockchip: fix rk3036 hdmi ports node
+    - ARM: dts: imx25/27-eukrea: Fix RTC node name
+    - ARM: dts: imx: Use flash@0,0 pattern
+    - ARM: dts: imx27: Fix sram node
+    - ARM: dts: imx1: Fix sram node
+    - ionic: pass opcode to devcmd_wait
+    - block/rnbd-srv: Check for unlikely string overflow
+    - ARM: dts: imx25: Fix the iim compatible string
+    - ARM: dts: imx25/27: Pass timing0
+    - ARM: dts: imx27-apf27dev: Fix LED name
+    - ARM: dts: imx23-sansa: Use preferred i2c-gpios properties
+    - ARM: dts: imx23/28: Fix the DMA controller node name
+    - net: dsa: mv88e6xxx: Fix mv88e6352_serdes_get_stats error path
+    - block: prevent an integer overflow in bvec_try_merge_hw_page
+    - md: Whenassemble the array, consult the superblock of the freshest device
+    - arm64: dts: qcom: msm8996: Fix 'in-ports' is a required property
+    - arm64: dts: qcom: msm8998: Fix 'out-ports' is a required property
+    - wifi: rtl8xxxu: Add additional USB IDs for RTL8192EU devices
+    - libbpf: Fix NULL pointer dereference in bpf_object__collect_prog_relos
+    - ALSA: usb-audio: Add delay quirk for MOTU M Series 2nd revision
+    - wifi: rtlwifi: rtl8723{be,ae}: using calculate_bit_shift()
+    - wifi: cfg80211: free beacon_ies when overridden from hidden BSS
+    - Bluetooth: qca: Set both WIDEBAND_SPEECH and LE_STATES quirks for QCA2066
+    - Bluetooth: L2CAP: Fix possible multiple reject send
+    - bridge: cfm: fix enum typo in br_cc_ccm_tx_parse
+    - i40e: Fix VF disable behavior to block all traffic
+    - octeontx2-af: Fix max NPC MCAM entry check while validating ref_entry
+    - f2fs: fix to check return value of f2fs_reserve_new_block()
+    - ALSA: hda: Refer to correct stream index at loops
+    - ASoC: doc: Fix undefined SND_SOC_DAPM_NOPM argument
+    - fast_dput(): handle underflows gracefully
+    - RDMA/IPoIB: Fix error code return in ipoib_mcast_join
+    - drm/amd/display: Fix tiled display misalignment
+    - f2fs: fix write pointers on zoned device after roll forward
+    - drm/drm_file: fix use of uninitialized variable
+    - drm/framebuffer: Fix use of uninitialized variable
+    - drm/mipi-dsi: Fix detach call without attach
+    - media: stk1160: Fixed high volume of stk1160_dbg messages
+    - media: rockchip: rga: fix swizzling for RGB formats
+    - PCI: add INTEL_HDA_ARL to pci_ids.h
+    - ALSA: hda: Intel: add HDA_ARL PCI ID support
+    - ALSA: hda: intel-dspcfg: add filters for ARL-S and ARL
+    - media: rkisp1: Drop IRQF_SHARED
+    - f2fs: fix to tag gcing flag on page during block migration
+    - drm/exynos: Call drm_atomic_helper_shutdown() at shutdown/unbind time
+    - IB/ipoib: Fix mcast list locking
+    - media: ddbridge: fix an error code problem in ddb_probe
+    - media: i2c: imx335: Fix hblank min/max values
+    - drm/msm/dpu: Ratelimit framedone timeout msgs
+    - drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap
+    - clk: hi3620: Fix memory leak in hi3620_mmc_clk_init()
+    - clk: mmp: pxa168: Fix memory leak in pxa168_clk_init()
+    - watchdog: it87_wdt: Keep WDTCTRL bit 3 unmodified for IT8784/IT8786
+    - clk: imx: scu: Fix memory leak in __imx_clk_gpr_scu()
+    - clk: imx: clk-imx8qxp: fix LVDS bypass, pixel and phy clocks
+    - drm/amdgpu: Let KFD sync with VM fences
+    - drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
+    - ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140
+    - leds: trigger: panic: Don't register panic notifier if creating the trigger
+      failed
+    - um: Fix naming clash between UML and scheduler
+    - um: Don't use vfprintf() for os_info()
+    - um: net: Fix return type of uml_net_start_xmit()
+    - um: time-travel: fix time corruption
+    - i3c: master: cdns: Update maximum prescaler value for i2c clock
+    - xen/gntdev: Fix the abuse of underlying struct page in DMA-buf import
+    - mfd: ti_am335x_tscadc: Fix TI SoC dependencies
+    - [Config] updateconfigs for MFD_TI_AM335X_TSCADC
+    - mailbox: arm_mhuv2: Fix a bug for mhuv2_sender_interrupt
+    - PCI: Only override AMD USB controller if required
+    - PCI: switchtec: Fix stdev_release() crash after surprise hot remove
+    - perf cs-etm: Bump minimum OpenCSD version to ensure a bugfix is present
+    - usb: hub: Replace hardcoded quirk value with BIT() macro
+    - selftests/sgx: Fix linker script asserts
+    - tty: allow TIOCSLCKTRMIOS with CAP_CHECKPOINT_RESTORE
+    - fs/kernfs/dir: obey S_ISGID
+    - PCI: Fix 64GT/s effective data rate calculation
+    - PCI/AER: Decode Requester ID when no error info found
+    - libsubcmd: Fix memory leak in uniq()
+    - drm/amdkfd: Fix lock dependency warning
+    - virtio_net: Fix "‘%d’ directive writing between 1 and 11 bytes into a region
+      of size 10" warnings
+    - blk-mq: fix IO hang from sbitmap wakeup race
+    - ceph: fix deadlock or deadcode of misusing dget()
+    - drm/amd/powerplay: Fix kzalloc parameter 'ATOM_Tonga_PPM_Table' in
+      'get_platform_power_management_table()'
+    - drm/amdgpu: Release 'adev->pm.fw' before return in
+      'amdgpu_device_need_post()'
+    - drm/amdkfd: Fix 'node' NULL check in 'svm_range_get_range_boundaries()'
+    - perf: Fix the nr_addr_filters fix
+    - wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
+    - drm: using mul_u32_u32() requires linux/math64.h
+    - scsi: isci: Fix an error code problem in isci_io_request_build()
+    - scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler
+    - selftests: net: give more time for GRO aggregation
+    - ip6_tunnel: use dev_sw_netstats_rx_add()
+    - ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()
+    - tcp: add sanity checks to rx zerocopy
+    - ixgbe: Remove non-inclusive language
+    - ixgbe: Refactor returning internal error codes
+    - ixgbe: Refactor overtemp event handling
+    - ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550()
+    - ipv6: Ensure natural alignment of const ipv6 loopback and router addresses
+    - llc: call sock_orphan() at release time
+    - bridge: mcast: fix disabled snooping after long uptime
+    - netfilter: nf_tables: restrict tunnel object to NFPROTO_NETDEV
+    - netfilter: nf_log: replace BUG_ON by WARN_ON_ONCE when putting logger
+    - netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom
+      expectations
+    - net: ipv4: fix a memleak in ip_setup_cork
+    - af_unix: fix lockdep positive in sk_diag_dump_icons()
+    - SAUCE: Sync apparmor copy of af_unix.c
+    - selftests: net: fix available tunnels detection
+    - net: sysfs: Fix /sys/class/net/<iface> path
+    - arm64: irq: set the correct node for shadow call stack
+    - gve: Fix use-after-free vulnerability
+    - HID: apple: Add support for the 2021 Magic Keyboard
+    - HID: apple: Add 2021 magic keyboard FN key mapping
+    - bonding: remove print in bond_verify_device_path
+    - ASoC: codecs: lpass-wsa-macro: fix compander volume hack
+    - dmaengine: fsl-dpaa2-qdma: Fix the size of dma pools
+    - dmaengine: ti: k3-udma: Report short packet errors
+    - dmaengine: fsl-qdma: Fix a memory leak related to the status queue DMA
+    - dmaengine: fsl-qdma: Fix a memory leak related to the queue command DMA
+    - phy: renesas: rcar-gen3-usb2: Fix returning wrong error code
+    - dmaengine: fix is_slave_direction() return false when DMA_DEV_TO_DEV
+    - phy: ti: phy-omap-usb2: Fix NULL pointer dereference for SRP
+    - drm/msm/dp: return correct Colorimetry for DP_TEST_DYNAMIC_RANGE_CEA case
+    - net: stmmac: xgmac: fix handling of DPP safety error for DMA channels
+    - selftests: net: cut more slack for gro fwd tests.
+    - selftests: net: avoid just another constant wait
+    - tunnels: fix out of bounds access when building IPv6 PMTU error
+    - atm: idt77252: fix a memleak in open_card_ubr0
+    - octeontx2-pf: Fix a memleak otx2_sq_init
+    - hwmon: (aspeed-pwm-tacho) mutex for tach reading
+    - hwmon: (coretemp) Fix out-of-bounds memory access
+    - hwmon: (coretemp) Fix bogus core_id to attr name mapping
+    - inet: read sk->sk_family once in inet_recv_error()
+    - rxrpc: Fix response to PING RESPONSE ACKs to a dead call
+    - tipc: Check the bearer type before calling tipc_udp_nl_bearer_add()
+    - af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.
+    - ppp_async: limit MRU to 64K
+    - netfilter: nft_compat: reject unused compat flag
+    - netfilter: nft_compat: restrict match/target protocol to u16
+    - drm/amd/display: Fix multiple memory leaks reported by coverity
+    - drm/amd/display: Implement bounds check for stream encoder creation in
+      DCN301
+    - netfilter: nft_ct: reject direction for ct id
+    - netfilter: nft_set_pipapo: store index in scratch maps
+    - netfilter: nft_set_pipapo: add helper to release pcpu scratch area
+    - netfilter: nft_set_pipapo: remove scratch_aligned pointer
+    - fs/ntfs3: Fix an NULL dereference bug
+    - scsi: core: Move scsi_host_busy() out of host lock if it is for per-command
+    - blk-iocost: Fix an UBSAN shift-out-of-bounds warning
+    - drivers: lkdtm: fix clang -Wformat warning
+    - ALSA: usb-audio: Add a quirk for Yamaha YIT-W12TX transmitter
+    - USB: serial: qcserial: add new usb-id for Dell Wireless DW5826e
+    - USB: serial: option: add Fibocom FM101-GL variant
+    - USB: serial: cp210x: add ID for IMST iM871A-USB
+    - usb: dwc3: host: Set XHCI_SG_TRB_CACHE_SIZE_QUIRK
+    - usb: host: xhci-plat: Add support for XHCI_SG_TRB_CACHE_SIZE_QUIRK
+    - hrtimer: Report offline hrtimer enqueue
+    - Input: i8042 - fix strange behavior of touchpad on Clevo NS70PU
+    - Input: atkbd - skip ATKBD_CMD_SETLEDS when skipping ATKBD_CMD_GETID
+    - clocksource: Skip watchdog check for large watchdog intervals
+    - net: stmmac: xgmac: use #define for string constants
+    - net: stmmac: xgmac: fix a typo of register name in DPP safety handling
+    - btrfs: forbid creating subvol qgroups
+    - btrfs: forbid deleting live subvol qgroup
+    - btrfs: send: return EOPNOTSUPP on unknown flags
+    - of: unittest: Fix compile in the non-dynamic case
+    - wifi: iwlwifi: Fix some error codes
+    - net: openvswitch: limit the number of recursions from action sets
+    - spi: ppc4xx: Drop write-only variable
+    - ASoC: rt5645: Fix deadlock in rt5645_jack_detect_work()
+    - net: sysfs: Fix /sys/class/net/<iface> path for statistics
+    - MIPS: Add 'memory' clobber to csum_ipv6_magic() inline assembler
+    - i40e: Fix waiting for queues of all VSIs to be disabled
+    - scs: add CONFIG_MMU dependency for vfree_atomic()
+    - tracing/trigger: Fix to return error if failed to alloc snapshot
+    - mm/writeback: fix possible divide-by-zero in wb_dirty_limits(), again
+    - scsi: storvsc: Fix ring buffer size calculation
+    - ALSA: hda/realtek: Fix the external mic not being recognised for Acer Swift
+      1 SF114-32
+    - ALSA: hda/realtek: Enable Mute LED on HP Laptop 14-fq0xxx
+    - HID: i2c-hid-of: fix NULL-deref on failed power up
+    - HID: wacom: generic: Avoid reporting a serial of '0' to userspace
+    - HID: wacom: Do not register input devices until after hid_hw_start
+    - iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP
+    - usb: ucsi_acpi: Fix command completion handling
+    - USB: hub: check for alternate port before enabling A_ALT_HNP_SUPPORT
+    - usb: f_mass_storage: forbid async queue when shutdown happen
+    - usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend
+    - media: ir_toy: fix a memleak in irtoy_tx
+    - powerpc/kasan: Fix addr error caused by page alignment
+    - i2c: i801: Remove i801_set_block_buffer_mode
+    - i2c: i801: Fix block process call transactions
+    - modpost: trim leading spaces when processing source files list
+    - mptcp: fix data re-injection from stale subflow
+    - scsi: Revert "scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock"
+    - Revert "drm/amd: flush any delayed gfxoff on suspend entry"
+    - firewire: core: correct documentation of fw_csr_string() kernel API
+    - kbuild: Fix changing ELF file type for output of gen_btf for big endian
+    - nfc: nci: free rx_data_reassembly skb on NCI device cleanup
+    - net: hsr: remove WARN_ONCE() in send_hsr_supervision_frame()
+    - xen-netback: properly sync TX responses
+    - ALSA: hda/realtek: Enable headset mic on Vaio VJFE-ADL
+    - ASoC: codecs: wcd938x: handle deferred probe
+    - binder: signal epoll threads of self-work
+    - misc: fastrpc: Mark all sessions as invalid in cb_remove
+    - ext4: fix double-free of blocks due to wrong extents moved_len
+    - tracing: Fix wasted memory in saved_cmdlines logic
+    - staging: iio: ad5933: fix type mismatch regression
+    - iio: magnetometer: rm3100: add boundary check for the value read from
+      RM3100_REG_TMRC
+    - iio: core: fix memleak in iio_device_register_sysfs
+    - iio: accel: bma400: Fix a compilation problem
+    - media: rc: bpf attach/detach requires write permission
+    - drm/prime: Support page array >= 4GB
+    - hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove
+    - ring-buffer: Clean ring_buffer_poll_wait() error return
+    - serial: max310x: set default value when reading clock ready bit
+    - serial: max310x: improve crystal stable clock detection
+    - serial: max310x: fail probe if clock crystal is unstable
+    - powerpc/64: Set task pt_regs->link to the LR value on scv entry
+    - x86/Kconfig: Transmeta Crusoe is CPU family 5, not 6
+    - x86/mm/ident_map: Use gbpages only where full GB page should be mapped.
+    - mmc: slot-gpio: Allow non-sleeping GPIO ro
+    - ALSA: hda/conexant: Add quirk for SWS JS201D
+    - nilfs2: fix data corruption in dsync block recovery for small block sizes
+    - nilfs2: fix hang in nilfs_lookup_dirty_data_buffers()
+    - crypto: ccp - Fix null pointer dereference in __sev_platform_shutdown_locked
+    - nfp: use correct macro for LengthSelect in BAR config
+    - nfp: flower: prevent re-adding mac index for bonded port
+    - wifi: mac80211: reload info pointer in ieee80211_tx_dequeue()
+    - irqchip/irq-brcmstb-l2: Add write memory barrier before exit
+    - irqchip/gic-v3-its: Fix GICv4.1 VPE affinity update
+    - net: ethernet: ti: cpsw: enable mac_managed_pm to fix mdio
+    - s390/qeth: Fix potential loss of L3-IP@ in case of network issues
+    - net: ethernet: ti: cpsw_new: enable mac_managed_pm to fix mdio
+    - ceph: prevent use-after-free in encode_cap_msg()
+    - mm: hugetlb pages should not be reserved by shmat() if SHM_NORESERVE
+    - of: property: fix typo in io-channels
+    - can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
+    - can: j1939: Fix UAF in j1939_sk_match_filter during
+      setsockopt(SO_J1939_FILTER)
+    - pmdomain: core: Move the unused cleanup to a _sync initcall
+    - tracing: Inform kmemleak of saved_cmdlines allocation
+    - af_unix: Fix task hung while purging oob_skb in GC.
+    - dma-buf: add dma_fence_timestamp helper
+    - bus: moxtet: Add spi device table
+    - crypto: lib/mpi - Fix unexpected pointer access in mpi_ec_init
+    - usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
+    - usb: dwc3: ep0: Don't prepare beyond Setup stage
+    - usb: dwc3: gadget: Only End Transfer for ep0 data phase
+    - usb: dwc3: gadget: Delay issuing End Transfer
+    - usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
+    - usb: dwc3: gadget: Force sending delayed status during soft disconnect
+    - usb: dwc3: gadget: Submit endxfer command if delayed during disconnect
+    - usb: dwc3: gadget: Stall and restart EP0 if host is unresponsive
+    - usb: dwc3: gadget: Refactor EP0 forced stall/restart into a separate API
+    - usb: dwc3: gadget: Handle EP0 request dequeuing properly
+    - usb: dwc3: gadget: Queue PM runtime idle on disconnect event
+    - serial: 8250_exar: Fill in rs485_supported
+    - serial: 8250_exar: Set missing rs485_supported flag
+    - fbdev/defio: Early-out if page is already enlisted
+    - fbdev: Don't sort deferred-I/O pages by default
+    - fbdev: defio: fix the pagelist corruption
+    - fbdev: Track deferred-I/O pages in pageref struct
+    - fbdev: Rename pagelist to pagereflist for deferred I/O
+    - fbdev: Fix invalid page access after closing deferred I/O devices
+    - fbdev: Fix incorrect page mapping clearance at fb_deferred_io_release()
+    - fbdev: flush deferred IO before closing
+    - scripts/decode_stacktrace.sh: support old bash version
+    - scripts: decode_stacktrace: demangle Rust symbols
+    - scripts/decode_stacktrace.sh: optionally use LLVM utilities
+    - netfilter: ipset: fix performance regression in swap operation
+    - hrtimer: Ignore slack time for RT tasks in schedule_hrtimeout_range()
+    - net: prevent mss overflow in skb_segment()
+    - netfilter: ipset: Missing gc cancellations fixed
+    - sched/membarrier: reduce the ability to hammer on sys_membarrier
+    - nilfs2: fix potential bug in end_buffer_async_write
+    - nilfs2: replace WARN_ONs for invalid DAT metadata block requests
+    - arm64: Subscribe Microsoft Azure Cobalt 100 to ARM Neoverse N2 errata
+    - PM: runtime: Have devm_pm_runtime_enable() handle
+      pm_runtime_dont_use_autosuspend()
+    - drm/msm/dsi: Enable runtime PM
+    - net: bcmgenet: Fix EEE implementation
+    - fs/ntfs3: Add null pointer checks
+    - staging: fbtft: core: set smem_len before fb_deferred_io_init call
+    - usb: dwc3: gadget: Don't delay End Transfer on delayed_status
+    - usb: dwc3: gadget: Execute gadget stop after halting the controller
+    - media: Revert "media: rkisp1: Drop IRQF_SHARED"
+    - usb: dwc3: gadget: Ignore End Transfer delay on teardown
+    - Linux 5.15.149
+  * Fix headphone mic detection issue on ALC897 (LP: #2056418)
+    - ALSA: hda/realtek - Fix headset Mic no show at resume back for Lenovo ALC897
+      platform
+  * CVE-2023-6039
+    - timers: Replace BUG_ON()s
+  * Problems with HVCS and hotplugging (LP: #2056373)
+    - hvcs: Fix hvcs port reference counting
+    - hvcs: Use dev_groups to manage hvcs device attributes
+    - hvcs: Use driver groups to manage driver attributes
+    - hvcs: Get reference to tty in remove
+    - hvcs: Use vhangup in hotplug remove
+    - hvcs: Synchronize hotplug remove with port free
+  * KVM: arm64: softlockups in stage2_apply_range (LP: #2056227)
+    - KVM: arm64: Work out supported block level at compile time
+    - KVM: arm64: Limit stage2_apply_range() batch size to largest block
+
+  [ Ubuntu: 5.15.0-105.115 ]
+
+  * jammy/linux: 5.15.0-105.115 -proposed tracker (LP: #2061372)
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014) // CIFS
+    stopped working/is unstable with kernel update to 5.15.0-102.112
+    (LP: #2060780)
+    - smb3: Replace smb2pdu 1-element arrays with flex-arrays
+
+  [ Ubuntu: 5.15.0-103.113 ]
+
+  * jammy/linux: 5.15.0-103.113 -proposed tracker (LP: #2059683)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop getabis data
+  * Remove getabis scripts (LP: #2059143)
+    - [Packaging] Remove getabis
+  * CVE-2023-24023
+    - Bluetooth: Add more enc key size check
+  * CVE-2023-52600
+    - jfs: fix uaf in jfs_evict_inode
+  * Jammy update: v5.15.149 upstream stable release (LP: #2059014) //
+    CVE-2023-52603
+    - UBSAN: array-index-out-of-bounds in dtSplitRoot
+  * CVE-2024-26581
+    - netfilter: nft_set_rbtree: skip end interval element from gc
+
+  [ Ubuntu: 5.15.0-102.112 ]
+
+  * jammy/linux: 5.15.0-102.112 -proposed tracker (LP: #2055632)
+  * Drop ABI checks from kernel build (LP: #2055686)
+    - [Packaging] Remove in-tree abi checks
+    - [Packaging] Drop abi checks from final-checks
+  * Packaging resync (LP: #1786013)
+    - [Packaging] drop ABI data
+    - [Packaging] update annotations scripts
+    - debian.master/dkms-versions -- update from kernel-versions (main/2024.03.04)
+  * block/loop: No longer allows to create partitions (LP: #2056143)
+    - block, loop: support partitions without scanning
+  * Cranky update-dkms-versions rollout (LP: #2055685)
+    - [Packaging] remove update-dkms-versions
+    - Move debian/dkms-versions to debian.master/dkms-versions
+    - [Packaging] Replace debian/dkms-versions with $(DEBIAN)/dkms-versions
+    - [Packaging] remove update-version-dkms
+  * linux: please move erofs.ko (CONFIG_EROFS for EROFS support) from linux-
+    modules-extra to linux-modules (LP: #2054809)
+    - UBUNTU [Packaging]: Include erofs in linux-modules instead of linux-modules-
+      extra
+  * linux-tools-common: man page of usbip[d] is misplaced (LP: #2054094)
+    - [Packaging] rules: Put usbip manpages in the correct directory
+  * CVE-2024-23851
+    - dm ioctl: log an error if the ioctl structure is corrupted
+    - dm: limit the number of targets and parameter size area
+  * CVE-2024-23850
+    - btrfs: do not ASSERT() if the newly created subvolume already got read
+  * x86: performance: tsc: Extend watchdog check exemption to 4-Sockets platform
+    (LP: #2054699)
+    - x86/tsc: Extend watchdog check exemption to 4-Sockets platform
+  * linux: please move dmi-sysfs.ko (CONFIG_DMI_SYSFS for SMBIOS support) from
+    linux-modules-extra to linux-modules (LP: #2045561)
+    - [Packaging] Move dmi-sysfs.ko into linux-modules
+  * Fix bpf selftests build failure after v5.15.139 update (LP: #2054567)
+    - Revert "selftests/bpf: Test tail call counting with bpf2bpf and data on
+      stack"
+  * Jammy update: v5.15.148 upstream stable release (LP: #2055145)
+    - f2fs: explicitly null-terminate the xattr list
+    - pinctrl: lochnagar: Don't build on MIPS
+    - ALSA: hda - Fix speaker and headset mic pin config for CHUWI CoreBook XPro
+    - mptcp: fix uninit-value in mptcp_incoming_options
+    - wifi: cfg80211: lock wiphy mutex for rfkill poll
+    - debugfs: fix automount d_fsdata usage
+    - drm/amdgpu: Fix cat debugfs amdgpu_regs_didt causes kernel null pointer
+    - nvme-core: check for too small lba shift
+    - ASoC: wm8974: Correct boost mixer inputs
+    - ASoC: Intel: Skylake: Fix mem leak in few functions
+    - ASoC: nau8822: Fix incorrect type in assignment and cast to restricted
+      __be16
+    - ASoC: Intel: Skylake: mem leak in skl register function
+    - ASoC: cs43130: Fix the position of const qualifier
+    - ASoC: cs43130: Fix incorrect frame delay configuration
+    - ASoC: rt5650: add mutex to avoid the jack detection failure
+    - nouveau/tu102: flush all pdbs on vmm flush
+    - net/tg3: fix race condition in tg3_reset_task()
+    - ASoC: da7219: Support low DC impedance headset
+    - ASoC: ops: add correct range check for limiting volume
+    - nvme: introduce helper function to get ctrl state
+    - drm/amdgpu: Add NULL checks for function pointers
+    - drm/exynos: fix a potential error pointer dereference
+    - drm/exynos: fix a wrong error checking
+    - hwmon: (corsair-psu) Fix probe when built-in
+    - clk: rockchip: rk3128: Fix HCLK_OTG gate register
+    - jbd2: correct the printing of write_flags in jbd2_write_superblock()
+    - drm/crtc: Fix uninit-value bug in drm_mode_setcrtc
+    - neighbour: Don't let neigh_forced_gc() disable preemption for long
+    - platform/x86: intel-vbtn: Fix missing tablet-mode-switch events
+    - jbd2: fix soft lockup in journal_finish_inode_data_buffers()
+    - tracing: Have large events show up as '[LINE TOO BIG]' instead of nothing
+    - tracing: Add size check when printing trace_marker output
+    - stmmac: dwmac-loongson: drop useless check for compatible fallback
+    - MIPS: dts: loongson: drop incorrect dwmac fallback compatible
+    - tracing: Fix uaf issue when open the hist or hist_debug file
+    - ring-buffer: Do not record in NMI if the arch does not support cmpxchg in
+      NMI
+    - reset: hisilicon: hi6220: fix Wvoid-pointer-to-enum-cast warning
+    - Input: atkbd - skip ATKBD_CMD_GETID in translated mode
+    - Input: i8042 - add nomux quirk for Acer P459-G2-M
+    - s390/scm: fix virtual vs physical address confusion
+    - ARC: fix spare error
+    - wifi: iwlwifi: pcie: avoid a NULL pointer dereference
+    - Input: xpad - add Razer Wolverine V2 support
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Medion Lifetab S10346
+    - i2c: rk3x: fix potential spinlock recursion on poll
+    - net: qrtr: ns: Return 0 if server port is not present
+    - ARM: sun9i: smp: fix return code check of of_property_match_string
+    - drm/crtc: fix uninitialized variable use
+    - ACPI: resource: Add another DMI match for the TongFang GMxXGxx
+    - Revert "ASoC: atmel: Remove system clock tree configuration for
+      at91sam9g20ek"
+    - bpf: Add --skip_encoding_btf_inconsistent_proto, --btf_gen_optimized to
+      pahole flags for v1.25
+    - kprobes: Fix to handle forcibly unoptimized kprobes on freeing_list
+    - Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"
+    - binder: use EPOLLERR from eventpoll.h
+    - binder: fix use-after-free in shinker's callback
+    - binder: fix trivial typo of binder_free_buf_locked()
+    - binder: fix comment on binder_alloc_new_buf() return value
+    - uio: Fix use-after-free in uio_open
+    - parport: parport_serial: Add Brainboxes BAR details
+    - parport: parport_serial: Add Brainboxes device IDs and geometry
+    - leds: ledtrig-tty: Free allocated ttyname buffer on deactivate
+    - PCI: Add ACS quirk for more Zhaoxin Root Ports
+    - coresight: etm4x: Fix width of CCITMIN field
+    - x86/lib: Fix overflow when counting digits
+    - EDAC/thunderx: Fix possible out-of-bounds string access
+    - powerpc: Mark .opd section read-only
+    - powerpc/toc: Future proof kernel toc
+    - powerpc: remove checks for binutils older than 2.25
+    - powerpc: add crtsavres.o to always-y instead of extra-y
+    - powerpc/44x: select I2C for CURRITUCK
+    - powerpc/pseries/memhp: Fix access beyond end of drmem array
+    - selftests/powerpc: Fix error handling in FPU/VMX preemption tests
+    - powerpc/powernv: Add a null pointer check to scom_debug_init_one()
+    - powerpc/powernv: Add a null pointer check in opal_event_init()
+    - powerpc/powernv: Add a null pointer check in opal_powercap_init()
+    - powerpc/imc-pmu: Add a null pointer check in update_events_in_group()
+    - spi: spi-zynqmp-gqspi: fix driver kconfig dependencies
+    - mtd: rawnand: Increment IFC_TIMEOUT_MSECS for nand controller response
+    - ACPI: video: check for error while searching for backlight device parent
+    - ACPI: LPIT: Avoid u32 multiplication overflow
+    - of: property: define of_property_read_u{8,16,32,64}_array() unconditionally
+    - of: Add of_property_present() helper
+    - cpufreq: Use of_property_present() for testing DT property presence
+    - cpufreq: scmi: process the result of devm_of_clk_add_hw_provider()
+    - calipso: fix memory leak in netlbl_calipso_add_pass()
+    - efivarfs: force RO when remounting if SetVariable is not supported
+    - spi: sh-msiof: Enforce fixed DTDL for R-Car H3
+    - ACPI: LPSS: Fix the fractional clock divider flags
+    - ACPI: extlog: Clear Extended Error Log status when RAS_CEC handled the error
+    - kunit: debugfs: Fix unchecked dereference in debugfs_print_results()
+    - mtd: Fix gluebi NULL pointer dereference caused by ftl notifier
+    - selinux: Fix error priority for bind with AF_UNSPEC on PF_INET6 socket
+    - crypto: virtio - Handle dataq logic with tasklet
+    - crypto: sa2ul - Return crypto_aead_setkey to transfer the error
+    - crypto: ccp - fix memleak in ccp_init_dm_workarea
+    - crypto: af_alg - Disallow multiple in-flight AIO requests
+    - crypto: sahara - remove FLAGS_NEW_KEY logic
+    - crypto: sahara - fix cbc selftest failure
+    - crypto: sahara - fix ahash selftest failure
+    - crypto: sahara - fix processing requests with cryptlen < sg->length
+    - crypto: sahara - fix error handling in sahara_hw_descriptor_create()
+    - pstore: ram_core: fix possible overflow in persistent_ram_init_ecc()
+    - fs: indicate request originates from old mount API
+    - gfs2: Fix kernel NULL pointer dereference in gfs2_rgrp_dump
+    - crypto: virtio - Wait for tasklet to complete on device remove
+    - crypto: sahara - avoid skcipher fallback code duplication
+    - crypto: sahara - handle zero-length aes requests
+    - crypto: sahara - fix ahash reqsize
+    - crypto: sahara - fix wait_for_completion_timeout() error handling
+    - crypto: sahara - improve error handling in sahara_sha_process()
+    - crypto: sahara - fix processing hash requests with req->nbytes < sg->length
+    - crypto: sahara - do not resize req->src when doing hash operations
+    - crypto: scomp - fix req->dst buffer overflow
+    - blocklayoutdriver: Fix reference leak of pnfs_device_node
+    - NFSv4.1/pnfs: Ensure we handle the error NFS4ERR_RETURNCONFLICT
+    - wifi: rtw88: fix RX filter in FIF_ALLMULTI flag
+    - bpf, lpm: Fix check prefixlen before walking trie
+    - bpf: Add crosstask check to __bpf_get_stack
+    - wifi: ath11k: Defer on rproc_get failure
+    - wifi: libertas: stop selecting wext
+    - ARM: dts: qcom: apq8064: correct XOADC register address
+    - net/ncsi: Fix netlink major/minor version numbers
+    - firmware: ti_sci: Fix an off-by-one in ti_sci_debugfs_create()
+    - firmware: meson_sm: populate platform devices from sm device tree data
+    - wifi: rtlwifi: rtl8821ae: phy: fix an undefined bitwise shift behavior
+    - arm64: dts: ti: k3-am65-main: Fix DSS irq trigger type
+    - bpf: enforce precision of R0 on callback return
+    - ARM: dts: qcom: sdx65: correct SPMI node name
+    - arm64: dts: qcom: sc7180: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sc7280: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sdm845: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sm8150: Make watchdog bark interrupt edge triggered
+    - arm64: dts: qcom: sm8250: Make watchdog bark interrupt edge triggered
+    - bpf: fix check for attempt to corrupt spilled pointer
+    - scsi: fnic: Return error if vmalloc() failed
+    - arm64: dts: qcom: qrb5165-rb5: correct LED panic indicator
+    - arm64: dts: qcom: sdm845-db845c: correct LED panic indicator
+    - arm64: dts: qcom: sc7280: fix usb_2 wakeup interrupt types
+    - bpf: Fix verification of indirect var-off stack access
+    - block: Set memalloc_noio to false on device_add_disk() error path
+    - scsi: hisi_sas: Rename HISI_SAS_{RESET -> RESETTING}_BIT
+    - scsi: hisi_sas: Prevent parallel FLR and controller reset
+    - scsi: hisi_sas: Replace with standard error code return value
+    - scsi: hisi_sas: Rollback some operations if FLR failed
+    - scsi: hisi_sas: Correct the number of global debugfs registers
+    - selftests/net: fix grep checking for fib_nexthop_multiprefix
+    - virtio/vsock: fix logic which reduces credit update messages
+    - dma-mapping: Add dma_release_coherent_memory to DMA API
+    - dma-mapping: clear dev->dma_mem to NULL after freeing it
+    - soc: qcom: llcc: Fix dis_cap_alloc and retain_on_pc configuration
+    - arm64: dts: qcom: sm8150-hdk: fix SS USB regulators
+    - block: add check of 'minors' and 'first_minor' in device_add_disk()
+    - arm64: dts: qcom: sc7280: Mark SDHCI hosts as cache-coherent
+    - wifi: rtlwifi: add calculate_bit_shift()
+    - wifi: rtlwifi: rtl8188ee: phy: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192c: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192cu: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192ce: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192de: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192ee: using calculate_bit_shift()
+    - wifi: rtlwifi: rtl8192se: using calculate_bit_shift()
+    - wifi: iwlwifi: mvm: set siso/mimo chains to 1 in FW SMPS request
+    - wifi: iwlwifi: mvm: send TX path flush in rfkill
+    - netfilter: nf_tables: mark newset as dead on transaction abort
+    - Bluetooth: Fix bogus check for re-auth no supported with non-ssp
+    - Bluetooth: btmtkuart: fix recv_buf() return value
+    - block: make BLK_DEF_MAX_SECTORS unsigned
+    - null_blk: don't cap max_hw_sectors to BLK_DEF_MAX_SECTORS
+    - net/sched: act_ct: fix skb leak and crash on ooo frags
+    - mlxbf_gige: Fix intermittent no ip issue
+    - net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
+    - mlxbf_gige: Enable the GigE port in mlxbf_gige_open
+    - ip6_tunnel: fix NEXTHDR_FRAGMENT handling in ip6_tnl_parse_tlv_enc_lim()
+    - ARM: davinci: always select CONFIG_CPU_ARM926T
+    - Revert "drm/tidss: Annotate dma-fence critical section in commit path"
+    - Revert "drm/omapdrm: Annotate dma-fence critical section in commit path"
+    - RDMA/usnic: Silence uninitialized symbol smatch warnings
+    - RDMA/hns: Fix inappropriate err code for unsupported operations
+    - drm/panel-elida-kd35t133: hold panel in reset for unprepare
+    - drm/nouveau/fence:: fix warning directly dereferencing a rcu pointer
+    - drm/bridge: tpd12s015: Drop buggy __exit annotation for remove function
+    - drm/tilcdc: Fix irq free on unload
+    - media: pvrusb2: fix use after free on context disconnection
+    - drm/bridge: Fix typo in post_disable() description
+    - f2fs: fix to avoid dirent corruption
+    - drm/radeon/r600_cs: Fix possible int overflows in r600_cs_check_reg()
+    - drm/radeon/r100: Fix integer overflow issues in r100_cs_track_check()
+    - drm/radeon: check return value of radeon_ring_lock()
+    - ASoC: cs35l33: Fix GPIO name and drop legacy include
+    - ASoC: cs35l34: Fix GPIO name and drop legacy include
+    - drm/msm/mdp4: flush vblank event on disable
+    - drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks
+    - drm/drv: propagate errors from drm_modeset_register_all()
+    - drm/radeon: check the alloc_workqueue return value in radeon_crtc_init()
+    - drm/radeon/dpm: fix a memleak in sumo_parse_power_table
+    - drm/radeon/trinity_dpm: fix a memleak in trinity_parse_power_table
+    - drm/bridge: cdns-mhdp8546: Fix use of uninitialized variable
+    - drm/bridge: tc358767: Fix return value on error case
+    - media: cx231xx: fix a memleak in cx231xx_init_isoc
+    - clk: qcom: gpucc-sm8150: Update the gpu_cc_pll1 config
+    - media: rkisp1: Disable runtime PM in probe error path
+    - f2fs: fix to check compress file in f2fs_move_file_range()
+    - f2fs: fix to update iostat correctly in f2fs_filemap_fault()
+    - f2fs: fix the f2fs_file_write_iter tracepoint
+    - media: dvbdev: drop refcount on error path in dvb_device_open()
+    - media: dvb-frontends: m88ds3103: Fix a memory leak in an error handling path
+      of m88ds3103_probe()
+    - drm/amdgpu/debugfs: fix error code when smc register accessors are NULL
+    - drm/amd/pm: fix a double-free in si_dpm_init
+    - drivers/amd/pm: fix a use-after-free in kv_parse_power_table
+    - gpu/drm/radeon: fix two memleaks in radeon_vm_init
+    - dt-bindings: clock: Update the videocc resets for sm8150
+    - clk: qcom: videocc-sm8150: Update the videocc resets
+    - clk: qcom: videocc-sm8150: Add missing PLL config property
+    - drivers: clk: zynqmp: calculate closest mux rate
+    - clk: zynqmp: make bestdiv unsigned
+    - clk: zynqmp: Add a check for NULL pointer
+    - drivers: clk: zynqmp: update divider round rate logic
+    - watchdog: set cdev owner before adding
+    - watchdog/hpwdt: Only claim UNKNOWN NMI if from iLO
+    - watchdog: bcm2835_wdt: Fix WDIOC_SETTIMEOUT handling
+    - watchdog: rti_wdt: Drop runtime pm reference count when watchdog is unused
+    - clk: si5341: fix an error code problem in si5341_output_clk_set_rate
+    - clk: asm9260: use parent index to link the reference clock
+    - clk: fixed-rate: add devm_clk_hw_register_fixed_rate
+    - clk: fixed-rate: fix clk_hw_register_fixed_rate_with_accuracy_parent_hw
+    - pwm: stm32: Use regmap_clear_bits and regmap_set_bits where applicable
+    - pwm: stm32: Use hweight32 in stm32_pwm_detect_channels
+    - pwm: stm32: Fix enable count for clk in .probe()
+    - ASoC: rt5645: Drop double EF20 entry from dmi_platform_data[]
+    - ALSA: scarlett2: Add missing error check to scarlett2_config_save()
+    - ALSA: scarlett2: Add missing error check to scarlett2_usb_set_config()
+    - ALSA: scarlett2: Allow passing any output to line_out_remap()
+    - ALSA: scarlett2: Add missing error checks to *_ctl_get()
+    - ALSA: scarlett2: Add clamp() in scarlett2_mixer_ctl_put()
+    - mmc: sdhci_am654: Fix TI SoC dependencies
+    - [Config] update annotations for CONFIG_MMC_SDHCI_AM654
+    - [Config] remove sdhci_am654 module for armhf/ppc64el
+    - mmc: sdhci_omap: Fix TI SoC dependencies
+    - [Config] update annotations for CONFIG_MMC_SDHCI_OMAP
+    - [Config] remove sdhci-omap module for arm64/ppc64el
+    - IB/iser: Prevent invalidating wrong MR
+    - drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
+    - ksmbd: validate the zero field of packet header
+    - of: Fix double free in of_parse_phandle_with_args_map
+    - of: unittest: Fix of_count_phandle_with_args() expected value message
+    - selftests/bpf: Add assert for user stacks in test_task_stack
+    - binder: fix async space check for 0-sized buffers
+    - binder: fix unused alloc->free_async_space
+    - Input: atkbd - use ab83 as id when skipping the getid command
+    - dma-mapping: Fix build error unused-value
+    - virtio-crypto: fix memory leak in virtio_crypto_alg_skcipher_close_session()
+    - binder: fix race between mmput() and do_exit()
+    - tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
+    - usb: phy: mxs: remove CONFIG_USB_OTG condition for mxs_phy_is_otg_host()
+    - usb: dwc: ep0: Update request status in dwc3_ep0_stall_restart
+    - Revert "usb: dwc3: Soft reset phy on probe for host"
+    - Revert "usb: dwc3: don't reset device side if dwc3 was configured as host-
+      only"
+    - usb: chipidea: wait controller resume finished for wakeup irq
+    - usb: cdns3: fix uvc failure work since sg support enabled
+    - usb: cdns3: fix iso transfer error when mult is not zero
+    - usb: cdns3: Fix uvc fail when DMA cross 4k boundery since sg enabled
+    - Revert "usb: typec: class: fix typec_altmode_put_partner to put plugs"
+    - usb: typec: class: fix typec_altmode_put_partner to put plugs
+    - usb: mon: Fix atomicity violation in mon_bin_vma_fault
+    - serial: imx: Ensure that imx_uart_rs485_config() is called with enabled
+      clock
+    - ALSA: oxygen: Fix right channel of capture volume mixer
+    - ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx
+    - fbdev: flush deferred work in fb_deferred_io_fsync()
+    - scsi: mpi3mr: Refresh sdev queue depth after controller reset
+    - block: add check that partition length needs to be aligned with block size
+    - pwm: jz4740: Don't use dev_err_probe() in .request()
+    - io_uring/rw: ensure io->bytes_done is always initialized
+    - rootfs: Fix support for rootfstype= when root= is given
+    - Bluetooth: Fix atomicity violation in {min,max}_key_size_set
+    - bpf: Fix re-attachment branch in bpf_tracing_prog_attach
+    - iommu/arm-smmu-qcom: Add missing GMU entry to match table
+    - wifi: mt76: fix broken precal loading from MTD for mt7915
+    - wifi: rtlwifi: Remove bogus and dangerous ASPM disable/enable code
+    - wifi: rtlwifi: Convert LNKCTL change to PCIe cap RMW accessors
+    - wifi: mwifiex: configure BSSID consistently when starting AP
+    - PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support
+    - PCI: mediatek: Clear interrupt status before dispatching handler
+    - x86/kvm: Do not try to disable kvmclock if it was not enabled
+    - KVM: arm64: vgic-v4: Restore pending state on host userspace write
+    - KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cache
+    - iio: adc: ad7091r: Pass iio_dev to event handler
+    - HID: wacom: Correct behavior when processing some confidence == false
+      touches
+    - serial: sc16is7xx: add check for unsupported SPI modes during probe
+    - serial: sc16is7xx: set safe default SPI clock frequency
+    - iommu/dma: Trace bounce buffer usage when mapping buffers
+    - ARM: 9330/1: davinci: also select PINCTRL
+    - mfd: syscon: Fix null pointer dereference in of_syscon_register()
+    - leds: aw2013: Select missing dependency REGMAP_I2C
+    - mfd: intel-lpss: Fix the fractional clock divider flags
+    - mips: dmi: Fix early remap on MIPS32
+    - mips: Fix incorrect max_low_pfn adjustment
+    - riscv: Check if the code to patch lies in the exit section
+    - riscv: Fix module_alloc() that did not reset the linear mapping permissions
+    - MIPS: Alchemy: Fix an out-of-bound access in db1200_dev_setup()
+    - MIPS: Alchemy: Fix an out-of-bound access in db1550_dev_setup()
+    - power: supply: cw2015: correct time_to_empty units in sysfs
+    - power: supply: bq256xx: fix some problem in bq256xx_hw_init
+    - serial: 8250: omap: Don't skip resource freeing if
+      pm_runtime_resume_and_get() failed
+    - libapi: Add missing linux/types.h header to get the __u64 type on io.h
+    - software node: Let args be NULL in software_node_get_reference_args
+    - serial: imx: fix tx statemachine deadlock
+    - selftests/sgx: Fix uninitialized pointer dereference in error path
+    - selftests/sgx: Skip non X86_64 platform
+    - iio: adc: ad9467: Benefit from devm_clk_get_enabled() to simplify
+    - iio: adc: ad9467: fix reset gpio handling
+    - iio: adc: ad9467: don't ignore error codes
+    - iio: adc: ad9467: fix scale setting
+    - perf genelf: Set ELF program header addresses properly
+    - tty: change tty_write_lock()'s ndelay parameter to bool
+    - tty: early return from send_break() on TTY_DRIVER_HARDWARE_BREAK
+    - tty: don't check for signal_pending() in send_break()
+    - tty: use 'if' in send_break() instead of 'goto'
+    - usb: cdc-acm: return correct error code on unsupported break
+    - nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length
+    - nvmet-tcp: fix a crash in nvmet_req_complete()
+    - perf env: Avoid recursively taking env->bpf_progs.lock
+    - apparmor: avoid crash when parsed profile name is empty
+    - usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
+    - serial: imx: Correct clock error message in function probe()
+    - nvmet: re-fix tracing strncpy() warning
+    - nvmet-tcp: Fix the H2C expected PDU len calculation
+    - PCI: keystone: Fix race condition when initializing PHYs
+    - s390/pci: fix max size calculation in zpci_memcpy_toio()
+    - net: qualcomm: rmnet: fix global oob in rmnet_policy
+    - net: ethernet: ti: am65-cpsw: Fix max mtu to fit ethernet frames
+    - net: phy: micrel: populate .soft_reset for KSZ9131
+    - mptcp: mptcp_parse_option() fix for MPTCPOPT_MP_JOIN
+    - mptcp: drop unused sk in mptcp_get_options
+    - mptcp: strict validation before using mp_opt->hmac
+    - mptcp: use OPTION_MPTCP_MPJ_SYNACK in subflow_finish_connect()
+    - mptcp: use OPTION_MPTCP_MPJ_SYN in subflow_check_req()
+    - net: ravb: Fix dma_addr_t truncation in error case
+    - net: stmmac: ethtool: Fixed calltrace caused by unbalanced disable_irq_wake
+      calls
+    - bpf: Reject variable offset alu on PTR_TO_FLOW_KEYS
+    - net: dsa: vsc73xx: Add null pointer check to vsc73xx_gpio_probe
+    - netfilter: nf_tables: reject invalid set policy
+    - netfilter: nft_connlimit: move stateful fields out of expression data
+    - netfilter: nft_last: move stateful fields out of expression data
+    - netfilter: nft_quota: move stateful fields out of expression data
+    - netfilter: nft_limit: rename stateful structure
+    - netfilter: nft_limit: move stateful fields out of expression data
+    - netfilter: nf_tables: memcg accounting for dynamically allocated objects
+    - netfilter: nft_limit: do not ignore unsupported flags
+    - netfilter: nf_tables: do not allow mismatch field size and set key length
+    - netfilter: nf_tables: skip dead set elements in netlink dump
+    - netfilter: nf_tables: reject NFT_SET_CONCAT with not field length
+      description
+    - ipvs: avoid stat macros calls from preemptible context
+    - kdb: Fix a potential buffer overflow in kdb_local()
+    - ethtool: netlink: Add missing ethnl_ops_begin/complete
+    - mlxsw: spectrum_acl_erp: Fix error flow of pool allocation failure
+    - mlxsw: spectrum: Use 'bitmap_zalloc()' when applicable
+    - mlxsw: spectrum_acl_tcam: Add missing mutex_destroy()
+    - mlxsw: spectrum_acl_tcam: Make fini symmetric to init
+    - mlxsw: spectrum_acl_tcam: Reorder functions to avoid forward declarations
+    - mlxsw: spectrum_acl_tcam: Fix stack corruption
+    - selftests: mlxsw: qos_pfc: Adjust the test to support 8 lanes
+    - ipv6: mcast: fix data-race in ipv6_mc_down / mld_ifc_work
+    - i2c: s3c24xx: fix read transfers in polling mode
+    - i2c: s3c24xx: fix transferring more than one message in polling mode
+    - block: Remove special-casing of compound pages
+    - netfilter: nf_tables: typo NULL check in _clone() function
+    - netfilter: nft_connlimit: memleak if nf_ct_netns_get() fails
+    - netfilter: nft_limit: fix stateful object memory leak
+    - netfilter: nft_limit: Clone packet limits' cost value
+    - netfilter: nft_last: copy content when cloning expression
+    - netfilter: nft_quota: copy content when cloning expression
+    - arm64: dts: armada-3720-turris-mox: set irq type for RTC
+    - Revert "Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d""
+    - Linux 5.15.148
+  * CVE-2024-24855
+    - scsi: lpfc: Fix a possible data race in lpfc_unregister_fcf_rescan()
+  * performance: Scheduler: ratelimit updating of load_avg (LP: #2053251)
+    - sched/fair: Ratelimit update to tg->load_avg
+  * Jammy update: v5.15.147 upstream stable release (LP: #2054411)
+    - block: Don't invalidate pagecache for invalid falloc modes
+    - ALSA: hda/realtek: Fix mute and mic-mute LEDs for HP ProBook 440 G6
+    - Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"
+    - wifi: iwlwifi: pcie: don't synchronize IRQs from IRQ
+    - drm/bridge: ti-sn65dsi86: Never store more than msg->size bytes in AUX xfer
+    - nfc: llcp_core: Hold a ref to llcp_local->dev when holding a ref to
+      llcp_local
+    - octeontx2-af: Fix marking couple of structure as __packed
+    - drm/i915/dp: Fix passing the correct DPCD_REV for
+      drm_dp_set_phy_test_pattern
+    - i40e: Fix filter input checks to prevent config with invalid values
+    - igc: Report VLAN EtherType matching back to user
+    - igc: Check VLAN TCI mask
+    - igc: Check VLAN EtherType mask
+    - ASoC: fsl_rpmsg: Fix error handler with pm_runtime_enable
+    - mlxbf_gige: fix receive packet race condition
+    - net: sched: em_text: fix possible memory leak in em_text_destroy()
+    - r8169: Fix PCI error on system resume
+    - net: Implement missing getsockopt(SO_TIMESTAMPING_NEW)
+    - can: raw: add support for SO_TXTIME/SCM_TXTIME
+    - can: raw: add support for SO_MARK
+    - net-timestamp: extend SOF_TIMESTAMPING_OPT_ID to HW timestamps
+    - ARM: sun9i: smp: Fix array-index-out-of-bounds read in sunxi_mc_smp_init
+    - sfc: fix a double-free bug in efx_probe_filters
+    - net: bcmgenet: Fix FCS generation for fragmented skbuffs
+    - netfilter: nft_immediate: drop chain reference counter on error
+    - net: Save and restore msg_namelen in sock_sendmsg
+    - i40e: fix use-after-free in i40e_aqc_add_filters()
+    - ASoC: meson: g12a-toacodec: Validate written enum values
+    - ASoC: meson: g12a-tohdmitx: Validate written enum values
+    - ASoC: meson: g12a-toacodec: Fix event generation
+    - ASoC: meson: g12a-tohdmitx: Fix event generation for S/PDIF mux
+    - i40e: Restore VF MSI-X state during PCI reset
+    - igc: Fix hicredit calculation
+    - net/qla3xxx: fix potential memleak in ql_alloc_buffer_queues
+    - octeontx2-af: Don't enable Pause frames by default
+    - octeontx2-af: Set NIX link credits based on max LMAC
+    - octeontx2-af: Always configure NIX TX link credits based on max frame size
+    - octeontx2-af: Re-enable MAC TX in otx2_stop processing
+    - asix: Add check for usbnet_get_endpoints
+    - bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()
+    - net: Implement missing SO_TIMESTAMPING_NEW cmsg support
+    - selftests: secretmem: floor the memory size to the multiple of page_size
+    - mm/memory-failure: check the mapcount of the precise page
+    - firewire: ohci: suppress unexpected system reboot in AMD Ryzen machines and
+      ASM108x/VT630x PCIe cards
+    - x86/kprobes: fix incorrect return address calculation in
+      kprobe_emulate_call_indirect
+    - i2c: core: Fix atomic xfer check for non-preempt config
+    - mm: fix unmap_mapping_range high bits shift bug
+    - mmc: meson-mx-sdhc: Fix initialization frozen issue
+    - mmc: rpmb: fixes pause retune on all RPMB partitions.
+    - mmc: core: Cancel delayed work before releasing host
+    - mmc: sdhci-sprd: Fix eMMC init failure after hw reset
+    - ipv6: remove max_size check inline with ipv4
+    - perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
+    - kallsyms: Make module_kallsyms_on_each_symbol generally available
+    - tracing/kprobes: Fix symbol counting logic by looking at modules as well
+    - net: usb: ax88179_178a: remove redundant init code
+    - net: usb: ax88179_178a: move priv to driver_priv
+    - Linux 5.15.147
+  * CVE-2024-1085
+    - netfilter: nf_tables: check if catch-all set element is active in next
+      generation
+  * CVE-2023-23000
+    - phy: tegra: xusb: Fix return value of tegra_xusb_find_port_node function
+  * performance: mm/percpu-internal.h: Re-layout pcpu_chunk to mitigate false
+    sharing (LP: #2053152)
+    - percpu-internal/pcpu_chunk: re-layout pcpu_chunk structure to reduce false
+      sharing
+  * performance: address_space: add padding for i_map and i_mmap_rwsem to
+    mitigate a false sharing (LP: #2053069)
+    - fs/address_space: add alignment padding for i_map and i_mmap_rwsem to
+      mitigate a false sharing.
+  * cpufreq: intel_pstate: Enable HWP IO boost for all servers (LP: #2052817)
+    - cpufreq: intel_pstate: Enable HWP IO boost for all servers
+  * performance: mm/memcontrol.c: remove the redundant updating of
+    stats_flush_threshold (LP: #2052827)
+    - mm/memcontrol.c: remove the redundant updating of stats_flush_threshold
+  * Jammy update: v5.15.146 upstream stable release (LP: #2053212)
+    - ARM: dts: dra7: Fix DRA7 L3 NoC node register size
+    - ARM: OMAP2+: Fix null pointer dereference and memory leak in
+      omap_soc_device_init
+    - reset: Fix crash when freeing non-existent optional resets
+    - s390/vx: fix save/restore of fpu kernel context
+    - wifi: iwlwifi: pcie: add another missing bh-disable for rxq->lock
+    - wifi: mac80211: mesh_plink: fix matches_local logic
+    - net/mlx5e: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list()
+    - net/mlx5e: fix a potential double-free in fs_udp_create_groups
+    - net/mlx5: Fix fw tracer first block check
+    - net/mlx5e: Correct snprintf truncation handling for fw_version buffer used
+      by representors
+    - net: sched: ife: fix potential use-after-free
+    - ethernet: atheros: fix a memleak in atl1e_setup_ring_resources
+    - net/rose: fix races in rose_kill_by_device()
+    - net: mana: select PAGE_POOL
+    - net: check vlan filter feature in vlan_vids_add_by_dev() and
+      vlan_vids_del_by_dev()
+    - afs: Fix the dynamic root's d_delete to always delete unused dentries
+    - afs: Fix dynamic root lookup DNS check
+    - net: check dev->gso_max_size in gso_features_check()
+    - keys, dns: Allow key types (eg. DNS) to be reclaimed immediately on expiry
+    - keys, dns: Fix missing size check of V1 server-list header
+    - keys, dns: Fix size check of V1 server-list header
+    - afs: Fix overwriting of result of DNS query
+    - afs: Use refcount_t rather than atomic_t
+    - afs: Fix use-after-free due to get/remove race in volume tree
+    - ASoC: hdmi-codec: fix missing report for jack initial status
+    - i2c: aspeed: Handle the coalesced stop conditions with the start conditions.
+    - pinctrl: at91-pio4: use dedicated lock class for IRQ
+    - gpiolib: cdev: add gpio_device locking wrapper around gpio_ioctl()
+    - ksmbd: fix wrong name of SMB2_CREATE_ALLOCATION_SIZE
+    - drm/i915/mtl: limit second scaler vertical scaling in ver >= 14
+    - drm/i915: Relocate intel_atomic_setup_scalers()
+    - drm/i915: Fix intel_atomic_setup_scalers() plane_state handling
+    - smb: client: fix NULL deref in asn1_ber_decoder()
+    - smb: client: fix OOB in smb2_query_reparse_point()
+    - interconnect: Treat xlate() returning NULL node as an error
+    - iio: imu: inv_mpu6050: fix an error code problem in inv_mpu6050_read_raw
+    - Input: ipaq-micro-keys - add error handling for devm_kmemdup
+    - scsi: bnx2fc: Fix skb double free in bnx2fc_rcv()
+    - iio: common: ms_sensors: ms_sensors_i2c: fix humidity conversion time table
+    - iio: adc: ti_am335x_adc: Fix return value check of tiadc_request_dma()
+    - iio: triggered-buffer: prevent possible freeing of wrong buffer
+    - ALSA: usb-audio: Increase delay in MOTU M quirk
+    - wifi: cfg80211: Add my certificate
+    - wifi: cfg80211: fix certs build to not depend on file order
+    - USB: serial: ftdi_sio: update Actisense PIDs constant names
+    - USB: serial: option: add Quectel EG912Y module support
+    - USB: serial: option: add Foxconn T99W265 with new baseline
+    - USB: serial: option: add Quectel RM500Q R13 firmware support
+    - Bluetooth: hci_event: Fix not checking if HCI_OP_INQUIRY has been sent
+    - Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE
+    - Input: soc_button_array - add mapping for airplane mode button
+    - net: 9p: avoid freeing uninit memory in p9pdu_vreadf
+    - net: rfkill: gpio: set GPIO direction
+    - net: ks8851: Fix TX stall caused by TX buffer overrun
+    - dt-bindings: nvmem: mxs-ocotp: Document fsl,ocotp
+    - scsi: core: Always send batch on reset or error handling command
+    - tracing / synthetic: Disable events after testing in
+      synth_event_gen_test_init()
+    - bus: ti-sysc: Flush posted write only after srst_udelay
+    - gpio: dwapb: mask/unmask IRQ when disable/enale it
+    - lib/vsprintf: Fix %pfwf when current node refcount == 0
+    - KVM: arm64: vgic: Force vcpu vgic teardown on vcpu destroy
+    - x86/alternatives: Sync core before enabling interrupts
+    - fuse: share lookup state between submount and its parent
+    - ksmbd: have a dependency on cifs ARC4
+    - ksmbd: set epoch in create context v2 lease
+    - ksmbd: set v2 lease capability
+    - ksmbd: downgrade RWH lease caching state to RH for directory
+    - ksmbd: send v2 lease break notification for directory
+    - ksmbd: lazy v2 lease break on smb2_write()
+    - ksmbd: avoid duplicate opinfo_put() call on error of smb21_lease_break_ack()
+    - ksmbd: fix wrong allocation size update in smb2_open()
+    - ARM: dts: Fix occasional boot hang for am3 usb
+    - usb: fotg210-hcd: delete an incorrect bounds test
+    - ethernet: constify references to netdev->dev_addr in drivers
+    - net: usb: ax88179_178a: clean up pm calls
+    - net: usb: ax88179_178a: wol optimizations
+    - net: usb: ax88179_178a: avoid failed operations when device is disconnected
+    - device property: Add const qualifier to device_get_match_data() parameter
+    - spi: Introduce spi_get_device_match_data() helper
+    - iio: imu: adis16475: add spi_device_id table
+    - smb: client: fix OOB in SMB2_query_info_init()
+    - mm/filemap: avoid buffered read/write race to read inconsistent data
+    - ring-buffer: Fix wake ups when buffer_percent is set to 100
+    - tracing: Fix blocked reader of snapshot buffer
+    - ring-buffer: Remove useless update to write_stamp in rb_try_to_discard()
+    - ring-buffer: Fix slowpath of interrupted event
+    - dm-integrity: don't modify bio's immutable bio_vec in integrity_metadata()
+    - device property: Allow const parameter to dev_fwnode()
+    - bpf: Fix prog_array_map_poke_run map poke update
+    - Linux 5.15.146
+  * CVE-2023-46838
+    - xen-netback: don't produce zero-size SKB frags
+  * CVE-2024-1086
+    - netfilter: nf_tables: reject QUEUE/DROP verdict parameters
+  * disable Intel DMA remapping by default (LP: #1971699)
+    - [Config] update tracking bug for CONFIG_INTEL_IOMMU_DEFAULT_ON
+  * Validate connection interval to pass Bluetooth Test Suite (LP: #2052005)
+    - Bluetooth: Enforce validation on max value of connection interval
+  * Jammy update: v5.15.145 upstream stable release (LP: #2052406)
+    - ksmbd: use ksmbd_req_buf_next() in ksmbd_verify_smb_message()
+    - ksmdb: use cmd helper variable in smb2_get_ksmbd_tcon()
+    - ksmbd: Remove redundant 'flush_workqueue()' calls
+    - ksmbd: remove md4 leftovers
+    - ksmbd: remove smb2_buf_length in smb2_hdr
+    - ksmbd: remove smb2_buf_length in smb2_transform_hdr
+    - ksmbd: change LeaseKey data type to u8 array
+    - ksmbd: use oid registry functions to decode OIDs
+    - ksmbd: Remove unused parameter from smb2_get_name()
+    - ksmbd: Remove unused fields from ksmbd_file struct definition
+    - ksmbd: set both ipv4 and ipv6 in FSCTL_QUERY_NETWORK_INTERFACE_INFO
+    - ksmbd: Fix buffer_check_err() kernel-doc comment
+    - ksmbd: Fix smb2_set_info_file() kernel-doc comment
+    - ksmbd: Delete an invalid argument description in
+      smb2_populate_readdir_entry()
+    - ksmbd: Fix smb2_get_name() kernel-doc comment
+    - ksmbd: register ksmbd ib client with ib_register_client()
+    - ksmbd: set 445 port to smbdirect port by default
+    - ksmbd: smbd: call rdma_accept() under CM handler
+    - ksmbd: smbd: create MR pool
+    - ksmbd: smbd: change the default maximum read/write, receive size
+    - ksmbd: smbd: fix missing client's memory region invalidation
+    - ksmbd: smbd: validate buffer descriptor structures
+    - ksmbd: add support for key exchange
+    - ksmbd: use netif_is_bridge_port
+    - ksmbd: store fids as opaque u64 integers
+    - ksmbd: shorten experimental warning on loading the module
+    - ksmbd: Remove a redundant zeroing of memory
+    - ksmbd: replace usage of found with dedicated list iterator variable
+    - smb3: fix ksmbd bigendian bug in oplock break, and move its struct to
+      smbfs_common
+    - ksmbd: remove filename in ksmbd_file
+    - ksmbd: smbd: change prototypes of RDMA read/write related functions
+    - ksmbd: smbd: introduce read/write credits for RDMA read/write
+    - ksmbd: smbd: simplify tracking pending packets
+    - ksmbd: smbd: change the return value of get_sg_list
+    - ksmbd: smbd: handle multiple Buffer descriptors
+    - ksmbd: fix wrong smbd max read/write size check
+    - ksmbd: Fix some kernel-doc comments
+    - ksmbd: smbd: fix connection dropped issue
+    - ksmbd: smbd: relax the count of sges required
+    - ksmbd: smbd: Remove useless license text when SPDX-License-Identifier is
+      already used
+    - ksmbd: remove duplicate flag set in smb2_write
+    - ksmbd: remove unused ksmbd_share_configs_cleanup function
+    - ksmbd: use wait_event instead of schedule_timeout()
+    - ksmbd: request update to stale share config
+    - ksmbd: remove unnecessary generic_fillattr in smb2_open
+    - ksmbd: don't open-code file_path()
+    - ksmbd: don't open-code %pD
+    - ksmbd: constify struct path
+    - ksmbd: remove generic_fillattr use in smb2_open()
+    - ksmbd: casefold utf-8 share names and fix ascii lowercase conversion
+    - ksmbd: change security id to the one samba used for posix extension
+    - ksmbd: set file permission mode to match Samba server posix extension
+      behavior
+    - ksmbd: fill sids in SMB_FIND_FILE_POSIX_INFO response
+    - ksmbd: fix encryption failure issue for session logoff response
+    - ksmbd: set NTLMSSP_NEGOTIATE_SEAL flag to challenge blob
+    - ksmbd: decrease the number of SMB3 smbdirect server SGEs
+    - ksmbd: reduce server smbdirect max send/receive segment sizes
+    - ksmbd: hide socket error message when ipv6 config is disable
+    - ksmbd: make utf-8 file name comparison work in __caseless_lookup()
+    - ksmbd: call ib_drain_qp when disconnected
+    - ksmbd: validate share name from share config response
+    - ksmbd: replace one-element arrays with flexible-array members
+    - ksmbd: set SMB2_SESSION_FLAG_ENCRYPT_DATA when enforcing data encryption for
+      this share
+    - ksmbd: use F_SETLK when unlocking a file
+    - ksmbd: Fix resource leak in smb2_lock()
+    - ksmbd: Convert to use sysfs_emit()/sysfs_emit_at() APIs
+    - ksmbd: send proper error response in smb2_tree_connect()
+    - ksmbd: Implements sess->rpc_handle_list as xarray
+    - ksmbd: fix typo, syncronous->synchronous
+    - ksmbd: Remove duplicated codes
+    - ksmbd: update Kconfig to note Kerberos support and fix indentation
+    - ksmbd: Fix spelling mistake "excceed" -> "exceeded"
+    - ksmbd: Fix parameter name and comment mismatch
+    - ksmbd: fix possible memory leak in smb2_lock()
+    - ksmbd: fix wrong signingkey creation when encryption is AES256
+    - ksmbd: remove unused is_char_allowed function
+    - ksmbd: delete asynchronous work from list
+    - ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
+    - ksmbd: avoid out of bounds access in decode_preauth_ctxt()
+    - ksmbd: set NegotiateContextCount once instead of every inc
+    - ksmbd: avoid duplicate negotiate ctx offset increments
+    - ksmbd: remove unused compression negotiate ctx packing
+    - fs: introduce lock_rename_child() helper
+    - ksmbd: fix racy issue from using ->d_parent and ->d_name
+    - ksmbd: destroy expired sessions
+    - ksmbd: block asynchronous requests when making a delay on session setup
+    - ksmbd: fix racy issue from smb2 close and logoff with multichannel
+    - ksmbd: fix racy issue under cocurrent smb2 tree disconnect
+    - ksmbd: fix uninitialized pointer read in ksmbd_vfs_rename()
+    - ksmbd: fix uninitialized pointer read in smb2_create_link()
+    - ksmbd: fix multiple out-of-bounds read during context decoding
+    - ksmbd: fix UAF issue from opinfo->conn
+    - ksmbd: call putname after using the last component
+    - ksmbd: fix out-of-bound read in deassemble_neg_contexts()
+    - ksmbd: fix out-of-bound read in parse_lease_state()
+    - ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
+    - ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
+    - ksmbd: validate smb request protocol id
+    - ksmbd: add mnt_want_write to ksmbd vfs functions
+    - ksmbd: remove unused ksmbd_tree_conn_share function
+    - ksmbd: use kzalloc() instead of __GFP_ZERO
+    - ksmbd: return a literal instead of 'err' in ksmbd_vfs_kern_path_locked()
+    - ksmbd: Change the return value of ksmbd_vfs_query_maximal_access to void
+    - ksmbd: use kvzalloc instead of kvmalloc
+    - ksmbd: Replace the ternary conditional operator with min()
+    - ksmbd: fix out of bounds read in smb2_sess_setup
+    - ksmbd: add missing compound request handing in some commands
+    - ksmbd: Use struct_size() helper in ksmbd_negotiate_smb_dialect()
+    - ksmbd: Replace one-element array with flexible-array member
+    - ksmbd: Fix unsigned expression compared with zero
+    - ksmbd: check if a mount point is crossed during path lookup
+    - ksmbd: validate session id and tree id in compound request
+    - ksmbd: fix out of bounds in init_smb2_rsp_hdr()
+    - ksmbd: switch to use kmemdup_nul() helper
+    - ksmbd: add support for read compound
+    - ksmbd: fix wrong interim response on compound
+    - ksmbd: fix `force create mode' and `force directory mode'
+    - ksmbd: reduce descriptor size if remaining bytes is less than request size
+    - ksmbd: Fix one kernel-doc comment
+    - ksmbd: fix slub overflow in ksmbd_decode_ntlmssp_auth_blob()
+    - ksmbd: add missing calling smb2_set_err_rsp() on error
+    - ksmbd: remove experimental warning
+    - ksmbd: remove unneeded mark_inode_dirty in set_info_sec()
+    - ksmbd: fix passing freed memory 'aux_payload_buf'
+    - ksmbd: return invalid parameter error response if smb2 request is invalid
+    - ksmbd: check iov vector index in ksmbd_conn_write()
+    - ksmbd: fix race condition between session lookup and expire
+    - ksmbd: fix race condition with fp
+    - ksmbd: fix race condition from parallel smb2 logoff requests
+    - ksmbd: fix race condition from parallel smb2 lock requests
+    - ksmbd: fix race condition between tree conn lookup and disconnect
+    - ksmbd: fix wrong error response status by using set_smb2_rsp_status()
+    - ksmbd: fix Null pointer dereferences in ksmbd_update_fstate()
+    - ksmbd: fix potential double free on smb2_read_pipe() error path
+    - ksmbd: Remove unused field in ksmbd_user struct
+    - ksmbd: reorganize ksmbd_iov_pin_rsp()
+    - ksmbd: fix kernel-doc comment of ksmbd_vfs_setxattr()
+    - ksmbd: fix recursive locking in vfs helpers
+    - ksmbd: fix missing RDMA-capable flag for IPoIB device in
+      ksmbd_rdma_capable_netdev()
+    - ksmbd: add support for surrogate pair conversion
+    - ksmbd: no need to wait for binded connection termination at logoff
+    - ksmbd: fix kernel-doc comment of ksmbd_vfs_kern_path_locked()
+    - ksmbd: handle malformed smb1 message
+    - ksmbd: prevent memory leak on error return
+    - ksmbd: fix possible deadlock in smb2_open
+    - ksmbd: separately allocate ci per dentry
+    - ksmbd: move oplock handling after unlock parent dir
+    - ksmbd: release interim response after sending status pending response
+    - ksmbd: move setting SMB2_FLAGS_ASYNC_COMMAND and AsyncId
+    - ksmbd: don't update ->op_state as OPLOCK_STATE_NONE on error
+    - tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols
+    - kasan: disable kasan_non_canonical_hook() for HW tags
+    - Linux 5.15.145
+  * Jammy update: v5.15.144 upstream stable release (LP: #2052404)
+    - r8152: add vendor/device ID pair for D-Link DUB-E250
+    - r8152: add vendor/device ID pair for ASUS USB-C2500
+    - netfilter: nf_tables: fix 'exist' matching on bigendian arches
+    - mm/memory_hotplug: handle memblock_add_node() failures in
+      add_memory_resource()
+    - memblock: allow to specify flags with memblock_add_node()
+    - MIPS: Loongson64: Handle more memory types passed from firmware
+    - ksmbd: fix memory leak in smb2_lock()
+    - afs: Fix refcount underflow from error handling race
+    - HID: lenovo: Restrict detection of patched firmware only to USB cptkbd
+    - net: ipv6: support reporting otherwise unknown prefix flags in RTM_NEWPREFIX
+    - qca_debug: Prevent crash on TX ring changes
+    - qca_debug: Fix ethtool -G iface tx behavior
+    - qca_spi: Fix reset behavior
+    - atm: solos-pci: Fix potential deadlock on &cli_queue_lock
+    - atm: solos-pci: Fix potential deadlock on &tx_queue_lock
+    - net: vlan: introduce skb_vlan_eth_hdr()
+    - net: fec: correct queue selection
+    - octeontx2-af: fix a use-after-free in rvu_nix_register_reporters
+    - octeontx2-pf: Fix promisc mcam entry action
+    - octeontx2-af: Update RSS algorithm index
+    - qed: Fix a potential use-after-free in qed_cxt_tables_alloc
+    - net: Remove acked SYN flag from packet in the transmit queue correctly
+    - net: ena: Destroy correct number of xdp queues upon failure
+    - net: ena: Fix xdp drops handling due to multibuf packets
+    - net: ena: Fix XDP redirection error
+    - stmmac: dwmac-loongson: Make sure MDIO is initialized before use
+    - sign-file: Fix incorrect return values check
+    - vsock/virtio: Fix unsigned integer wrap around in
+      virtio_transport_has_space()
+    - dpaa2-switch: fix size of the dma_unmap
+    - net: stmmac: use dev_err_probe() for reporting mdio bus registration failure
+    - net: stmmac: Handle disabled MDIO busses from devicetree
+    - net: atlantic: fix double free in ring reinit logic
+    - cred: switch to using atomic_long_t
+    - fuse: dax: set fc->dax to NULL in fuse_dax_conn_free()
+    - ALSA: hda/hdmi: add force-connect quirk for NUC5CPYB
+    - ALSA: hda/hdmi: add force-connect quirks for ASUSTeK Z170 variants
+    - ALSA: hda/realtek: Apply mute LED quirk for HP15-db
+    - PCI: loongson: Limit MRRS to 256
+    - drm/mediatek: Add spinlock for setting vblank event in atomic_begin
+    - usb: aqc111: check packet for fixup for true limit
+    - stmmac: dwmac-loongson: Add architecture dependency
+    - [Config] updateconfigs for CONFIG_DWMAC_LOONGSON
+    - blk-throttle: fix lockdep warning of "cgroup_mutex or RCU read lock
+      required!"
+    - blk-cgroup: bypass blkcg_deactivate_policy after destroying
+    - bcache: avoid oversize memory allocation by small stripe_size
+    - bcache: remove redundant assignment to variable cur_idx
+    - bcache: add code comments for bch_btree_node_get() and
+      __bch_btree_node_alloc()
+    - bcache: avoid NULL checking to c->root in run_cache_set()
+    - platform/x86: intel_telemetry: Fix kernel doc descriptions
+    - HID: glorious: fix Glorious Model I HID report
+    - HID: add ALWAYS_POLL quirk for Apple kb
+    - HID: hid-asus: reset the backlight brightness level on resume
+    - HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
+    - asm-generic: qspinlock: fix queued_spin_value_unlocked() implementation
+    - net: usb: qmi_wwan: claim interface 4 for ZTE MF290
+    - HID: hid-asus: add const to read-only outgoing usb buffer
+    - btrfs: do not allow non subvolume root targets for snapshot
+    - soundwire: stream: fix NULL pointer dereference for multi_link
+    - ext4: prevent the normalized size from exceeding EXT_MAX_BLOCKS
+    - arm64: mm: Always make sw-dirty PTEs hw-dirty in pte_modify
+    - team: Fix use-after-free when an option instance allocation fails
+    - drm/amdgpu/sdma5.2: add begin/end_use ring callbacks
+    - ring-buffer: Fix memory leak of free page
+    - tracing: Update snapshot buffer on resize if it is allocated
+    - ring-buffer: Do not update before stamp when switching sub-buffers
+    - ring-buffer: Have saved event hold the entire event
+    - ring-buffer: Fix writing to the buffer with max_data_size
+    - ring-buffer: Fix a race in rb_time_cmpxchg() for 32 bit archs
+    - ring-buffer: Do not try to put back write_stamp
+    - USB: gadget: core: adjust uevent timing on gadget unbind
+    - powerpc/ftrace: Create a dummy stackframe to fix stack unwind
+    - powerpc/ftrace: Fix stack teardown in ftrace_no_trace
+    - r8152: avoid to change cfg for all devices
+    - r8152: remove rtl_vendor_mode function
+    - r8152: fix the autosuspend doesn't work
+    - Linux 5.15.144
+  * CVE-2023-32247
+    - ksmbd: destroy expired sessions
+  * CVE-2024-22705
+    - ksmbd: fix slab-out-of-bounds in smb_strndup_from_utf16()
+
+  [ Ubuntu: 5.15.0-100.110 ]
+
+  * jammy/linux: 5.15.0-100.110 -proposed tracker (LP: #2052616)
+  * i915 regression introduced with 5.5 kernel (LP: #2044131)
+    - drm/i915: Skip some timing checks on BXT/GLK DSI transcoders
+  * Audio balancing setting doesn't work with the cirrus codec (LP: #2051050)
+    - ALSA: hda/cs8409: Suppress vmaster control for Dolphin models
+  * partproke is broken on empty loopback device (LP: #2049689)
+    - block: Move checking GENHD_FL_NO_PART to bdev_add_partition()
+  * CVE-2023-0340
+    - vhost: use kzalloc() instead of kmalloc() followed by memset()
+  * CVE-2023-51780
+    - atm: Fix Use-After-Free in do_vcc_ioctl
+  * CVE-2023-6915
+    - ida: Fix crash in ida_free when the bitmap is empty
+  * CVE-2024-0646
+    - net: tls, update curr on splice as well
+  * CVE-2024-0565
+    - smb: client: fix OOB in receive_encrypted_standard()
+  * CVE-2023-51781
+    - appletalk: Fix Use-After-Free in atalk_ioctl
+  * Jammy update: v5.15.143 upstream stable release (LP: #2050858)
+    - vdpa/mlx5: preserve CVQ vringh index
+    - hrtimers: Push pending hrtimers away from outgoing CPU earlier
+    - i2c: designware: Fix corrupted memory seen in the ISR
+    - netfilter: ipset: fix race condition between swap/destroy and kernel side
+      add/del/test
+    - tg3: Move the [rt]x_dropped counters to tg3_napi
+    - tg3: Increment tx_dropped in tg3_tso_bug()
+    - kconfig: fix memory leak from range properties
+    - drm/amdgpu: correct chunk_ptr to a pointer to chunk.
+    - platform/x86: asus-wmi: Adjust tablet/lidflip handling to use enum
+    - platform/x86: asus-wmi: Add support for ROG X13 tablet mode
+    - platform/x86: asus-wmi: Simplify tablet-mode-switch probing
+    - platform/x86: asus-wmi: Simplify tablet-mode-switch handling
+    - platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code
+    - of: dynamic: Fix of_reconfig_get_state_change() return value documentation
+    - platform/x86: wmi: Allow duplicate GUIDs for drivers that use struct
+      wmi_driver
+    - platform/x86: wmi: Skip blocks with zero instances
+    - ipv6: fix potential NULL deref in fib6_add()
+    - octeontx2-pf: Add missing mutex lock in otx2_get_pauseparam
+    - octeontx2-af: Check return value of nix_get_nixlf before using nixlf
+    - hv_netvsc: rndis_filter needs to select NLS
+    - r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
+    - r8152: Add RTL8152_INACCESSIBLE checks to more loops
+    - r8152: Add RTL8152_INACCESSIBLE to r8156b_wait_loading_flash()
+    - r8152: Add RTL8152_INACCESSIBLE to r8153_pre_firmware_1()
+    - r8152: Add RTL8152_INACCESSIBLE to r8153_aldps_en()
+    - mlxbf-bootctl: correctly identify secure boot with development keys
+    - platform/mellanox: Add null pointer checks for devm_kasprintf()
+    - platform/mellanox: Check devm_hwmon_device_register_with_groups() return
+      value
+    - arcnet: restoring support for multiple Sohard Arcnet cards
+    - net: stmmac: fix FPE events losing
+    - octeontx2-af: fix a use-after-free in rvu_npa_register_reporters
+    - i40e: Fix unexpected MFS warning message
+    - net: bnxt: fix a potential use-after-free in bnxt_init_tc
+    - ionic: fix snprintf format length warning
+    - ionic: Fix dim work handling in split interrupt mode
+    - ipv4: ip_gre: Avoid skb_pull() failure in ipgre_xmit()
+    - net: hns: fix fake link up on xge port
+    - octeontx2-af: Update Tx link register range
+    - netfilter: nf_tables: validate family when identifying table via handle
+    - netfilter: xt_owner: Fix for unsafe access of sk->sk_socket
+    - tcp: do not accept ACK of bytes we never sent
+    - bpf: sockmap, updating the sg structure should also update curr
+    - psample: Require 'CAP_NET_ADMIN' when joining "packets" group
+    - net: add missing kdoc for struct genl_multicast_group::flags
+    - drop_monitor: Require 'CAP_SYS_ADMIN' when joining "events" group
+    - tee: optee: Fix supplicant based device enumeration
+    - RDMA/hns: Fix unnecessary err return when using invalid congest control
+      algorithm
+    - RDMA/irdma: Do not modify to SQD on error
+    - RDMA/irdma: Add wait for suspend on SQD
+    - arm64: dts: rockchip: Expand reg size of vdec node for RK3399
+    - RDMA/rtrs-srv: Do not unconditionally enable irq
+    - RDMA/rtrs-clt: Start hb after path_up
+    - RDMA/rtrs-srv: Check return values while processing info request
+    - RDMA/rtrs-srv: Free srv_mr iu only when always_invalidate is true
+    - RDMA/rtrs-srv: Destroy path files after making sure no IOs in-flight
+    - RDMA/rtrs-clt: Fix the max_send_wr setting
+    - RDMA/rtrs-clt: Remove the warnings for req in_use check
+    - RDMA/bnxt_re: Correct module description string
+    - hwmon: (acpi_power_meter) Fix 4.29 MW bug
+    - hwmon: (nzxt-kraken2) Fix error handling path in kraken2_probe()
+    - ASoC: wm_adsp: fix memleak in wm_adsp_buffer_populate
+    - RDMA/core: Fix umem iterator when PAGE_SIZE is greater then HCA pgsz
+    - RDMA/irdma: Avoid free the non-cqp_request scratch
+    - arm64: dts: imx8mq: drop usb3-resume-missing-cas from usb
+    - arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
+    - ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
+    - tracing: Fix a warning when allocating buffered events fails
+    - scsi: be2iscsi: Fix a memleak in beiscsi_init_wrb_handle()
+    - ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
+    - ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
+    - ARM: dts: imx28-xea: Pass the 'model' property
+    - riscv: fix misaligned access handling of C.SWSP and C.SDSP
+    - md: introduce md_ro_state
+    - md: don't leave 'MD_RECOVERY_FROZEN' in error path of md_set_readonly()
+    - kprobes: consistent rcu api usage for kretprobe holder
+    - nvme-pci: Add sleep quirk for Kingston drives
+    - io_uring: fix mutex_unlock with unreferenced ctx
+    - ALSA: usb-audio: Add Pioneer DJM-450 mixer controls
+    - ALSA: pcm: fix out-of-bounds in snd_pcm_state_names
+    - nilfs2: fix missing error check for sb_set_blocksize call
+    - nilfs2: prevent WARNING in nilfs_sufile_set_segment_usage()
+    - checkstack: fix printed address
+    - tracing: Always update snapshot buffer size
+    - tracing: Disable snapshot buffer when stopping instance tracers
+    - tracing: Fix incomplete locking when disabling buffered events
+    - tracing: Fix a possible race when disabling buffered events
+    - packet: Move reference count in packet_sock to atomic_long_t
+    - regmap: fix bogus error on regcache_sync success
+    - platform/surface: aggregator: fix recv_buf() return value
+    - arm64: dts: mediatek: mt7622: fix memory node warning check
+    - arm64: dts: mediatek: mt8183-kukui-jacuzzi: fix dsi unnecessary cells
+      properties
+    - arm64: dts: mediatek: mt8173-evb: Fix regulator-fixed node names
+    - arm64: dts: mediatek: mt8183: Fix unit address for scp reserved memory
+    - binder: fix memory leaks of spam and pending work
+    - kallsyms: Make kallsyms_on_each_symbol generally available
+    - coresight: etm4x: Make etm4_remove_dev() return void
+    - coresight: etm4x: Remove bogous __exit annotation for some functions
+    - misc: mei: client.c: return negative error code in mei_cl_write
+    - misc: mei: client.c: fix problem of return '-EOVERFLOW' in mei_cl_write
+    - ring-buffer: Force absolute timestamp on discard of event
+    - tracing: Set actual size after ring buffer resize
+    - tracing: Stop current tracer when resizing buffer
+    - r8169: fix rtl8125b PAUSE frames blasting when suspended
+    - mm: fix oops when filemap_map_pmd() without prealloc_pte
+    - io_uring/af_unix: disable sending io_uring over sockets
+    - platform/x86: asus-wmi: Fix kbd_dock_devid tablet-switch reporting
+    - docs/process/howto: Replace C89 with C11
+    - tools headers UAPI: Sync linux/perf_event.h with the kernel sources
+    - arm64: dts: mediatek: align thermal zone node names with dtschema
+    - arm64: dts: mediatek: mt8183: Move thermal-zones to the root node
+    - arm64: dts: mediatek: add missing space before {
+    - arm64: dts: mt8183: kukui: Fix underscores in node names
+    - gpiolib: sysfs: Fix error handling on failed export
+    - drm/amd/amdgpu: Fix warnings in amdgpu/amdgpu_display.c
+    - drm/amdgpu: correct the amdgpu runtime dereference usage count
+    - usb: gadget: f_hid: fix report descriptor allocation
+    - parport: Add support for Brainboxes IX/UC/PX parallel cards
+    - usb: typec: class: fix typec_altmode_put_partner to put plugs
+    - ARM: PL011: Fix DMA support
+    - serial: sc16is7xx: address RX timeout interrupt errata
+    - serial: 8250: 8250_omap: Clear UART_HAS_RHR_IT_DIS bit
+    - serial: 8250: 8250_omap: Do not start RX DMA on THRI interrupt
+    - serial: 8250_omap: Add earlycon support for the AM654 UART controller
+    - x86/CPU/AMD: Check vendor in the AMD microcode callback
+    - KVM: s390/mm: Properly reset no-dat
+    - KVM: SVM: Update EFER software model on CR0 trap for SEV-ES
+    - MIPS: Loongson64: Reserve vgabios memory on boot
+    - MIPS: Loongson64: Enable DMA noncoherent support
+    - cifs: Fix non-availability of dedup breaking generic/304
+    - smb: client: fix potential NULL deref in parse_dfs_referrals()
+    - devcoredump : Serialize devcd_del work
+    - devcoredump: Send uevent once devcd is ready
+    - Linux 5.15.143
+  * Intel E810-XXV - NETDEV WATCHDOG: (ice): transmit queue timed out
+    (LP: #2036239)
+    - ice: Add feature bitmap, helpers and a check for DSCP
+    - ice: Add driver support for firmware changes for LAG
+    - ice: alter feature support check for SRIOV and LAG
+  * Don't WARN_ON_ONCE() for a broken discovery table (LP: #2048404)
+    - perf/x86/uncore: Don't WARN_ON_ONCE() for a broken discovery table
+  * Reject connection when malformed L2CAP signal packet is received
+    (LP: #2047634)
+    - Bluetooth: L2CAP: Send reject on command corrupted request
+  * Jammy update: v5.15.142 upstream stable release (LP: #2050849)
+    - pinctrl: avoid reload of p state in list iteration
+    - firewire: core: fix possible memory leak in create_units()
+    - mmc: cqhci: Increase recovery halt timeout
+    - mmc: cqhci: Warn of halt or task clear failure
+    - mmc: cqhci: Fix task clearing in CQE error recovery
+    - mmc: block: Retry commands in CQE error recovery
+    - mmc: block: Do not lose cache flush during CQE error recovery
+    - mmc: block: Be sure to wait while busy in CQE error recovery
+    - ALSA: hda: Disable power-save on KONTRON SinglePC
+    - ALSA: hda/realtek: Headset Mic VREF to 100%
+    - ALSA: hda/realtek: Add supported ALC257 for ChromeOS
+    - dm-verity: align struct dm_verity_fec_io properly
+    - dm verity: don't perform FEC for failed readahead IO
+    - bcache: revert replacing IS_ERR_OR_NULL with IS_ERR
+    - iommu/vt-d: Add MTL to quirk list to skip TE disabling
+    - powerpc: Don't clobber f0/vs0 during fp|altivec register save
+    - parisc: Drop the HP-UX ENOSYM and EREMOTERELEASE error codes
+    - btrfs: ref-verify: fix memory leaks in btrfs_ref_tree_mod()
+    - btrfs: fix off-by-one when checking chunk map includes logical address
+    - btrfs: send: ensure send_fd is writable
+    - btrfs: make error messages more clear when getting a chunk map
+    - Input: xpad - add HyperX Clutch Gladiate Support
+    - vlan: introduce vlan_dev_free_egress_priority
+    - vlan: move dev_put into vlan_dev_uninit
+    - rcu: Avoid tracing a few functions executed in stop machine
+    - hv_netvsc: fix race of netvsc and VF register_netdevice
+    - USB: core: Change configuration warnings to notices
+    - usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
+    - dpaa2-eth: increase the needed headroom to account for alignment
+    - uapi: propagate __struct_group() attributes to the container union
+    - selftests/net: ipsec: fix constant out of range
+    - octeontx2-af: Fix possible buffer overflow
+    - net: stmmac: xgmac: Disable FPE MMC interrupts
+    - octeontx2-pf: Fix adding mbox work queue entry when num_vfs > 64
+    - Revert "workqueue: remove unused cancel_work()"
+    - r8169: prevent potential deadlock in rtl8169_close
+    - ravb: Fix races between ravb_tx_timeout_work() and net related ops
+    - net: ravb: Check return value of reset_control_deassert()
+    - net: ravb: Use pm_runtime_resume_and_get()
+    - net: ravb: Start TX queues after HW initialization succeeded
+    - net: ravb: Stop DMA in case of failures on ravb_open()
+    - perf intel-pt: Fix async branch flags
+    - selftests/resctrl: Add missing SPDX license to Makefile
+    - selftests/resctrl: Move _GNU_SOURCE define into Makefile
+    - smb3: fix touch -h of symlink
+    - ASoC: Intel: Move soc_intel_is_foo() helpers to a generic header
+    - ASoC: SOF: sof-pci-dev: use community key on all Up boards
+    - ASoC: SOF: sof-pci-dev: add parameter to override topology filename
+    - ASoC: SOF: sof-pci-dev: don't use the community key on APL Chromebooks
+    - ASoC: SOF: sof-pci-dev: Fix community key quirk detection
+    - fbdev: stifb: Make the STI next font pointer a 32-bit signed offset
+    - fs: add ctime accessors infrastructure
+    - smb3: fix caching of ctime on setxattr
+    - cpufreq: imx6q: don't warn for disabling a non-existing frequency
+    - cpufreq: imx6q: Don't disable 792 Mhz OPP unnecessarily
+    - iommu/vt-d: Omit devTLB invalidation requests when TES=0
+    - iommu/vt-d: Make context clearing consistent with context mapping
+    - mmc: core: add helpers mmc_regulator_enable/disable_vqmmc
+    - mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled
+    - r8169: disable ASPM in case of tx timeout
+    - r8169: fix deadlock on RTL8125 in jumbo mtu mode
+    - iomap: update ki_pos a little later in iomap_dio_complete
+    - Linux 5.15.142
+  * Jammy update: v5.15.141 upstream stable release (LP: #2050044)
+    - afs: Fix afs_server_list to be cleaned up with RCU
+    - afs: Make error on cell lookup failure consistent with OpenAFS
+    - drm/panel: boe-tv101wum-nl6: Fine tune the panel power sequence
+    - drm/panel: auo,b101uan08.3: Fine tune the panel power sequence
+    - drm/panel: simple: Fix Innolux G101ICE-L01 bus flags
+    - drm/panel: simple: Fix Innolux G101ICE-L01 timings
+    - wireguard: use DEV_STATS_INC()
+    - octeontx2-pf: Fix memory leak during interface down
+    - ata: pata_isapnp: Add missing error check for devm_ioport_map()
+    - drm/rockchip: vop: Fix color for RGB888/BGR888 format on VOP full
+    - HID: core: store the unique system identifier in hid_device
+    - HID: fix HID device resource race between HID core and debugging support
+    - ipv4: Correct/silence an endian warning in __ip_do_redirect
+    - net: usb: ax88179_178a: fix failed operations during ax88179_reset
+    - net/smc: avoid data corruption caused by decline
+    - arm/xen: fix xen_vcpu_info allocation alignment
+    - octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx
+      queue than its PF
+    - amd-xgbe: handle corner-case during sfp hotplug
+    - amd-xgbe: handle the corner-case during tx completion
+    - amd-xgbe: propagate the correct speed and duplex status
+    - net: axienet: Fix check for partial TX checksum
+    - afs: Return ENOENT if no cell DNS record can be found
+    - afs: Fix file locking on R/O volumes to operate in local mode
+    - nvmet: nul-terminate the NQNs passed in the connect command
+    - USB: dwc3: qcom: fix resource leaks on probe deferral
+    - USB: dwc3: qcom: fix ACPI platform device leak
+    - lockdep: Fix block chain corruption
+    - MIPS: KVM: Fix a build warning about variable set but not used
+    - media: camss: Replace hard coded value with parameter
+    - media: camss: sm8250: Virtual channels for CSID
+    - media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3
+    - media: qcom: camss: Fix csid-gen2 for test pattern generator
+    - ext4: add a new helper to check if es must be kept
+    - ext4: factor out __es_alloc_extent() and __es_free_extent()
+    - ext4: use pre-allocated es in __es_insert_extent()
+    - ext4: use pre-allocated es in __es_remove_extent()
+    - ext4: using nofail preallocation in ext4_es_remove_extent()
+    - ext4: using nofail preallocation in ext4_es_insert_delayed_block()
+    - ext4: using nofail preallocation in ext4_es_insert_extent()
+    - ext4: fix slab-use-after-free in ext4_es_insert_extent()
+    - ext4: make sure allocate pending entry not fail
+    - proc: sysctl: prevent aliased sysctls from getting passed to init
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CVA
+    - swiotlb-xen: provide the "max_mapping_size" method
+    - bcache: replace a mistaken IS_ERR() by IS_ERR_OR_NULL() in
+      btree_gc_coalesce()
+    - md: fix bi_status reporting in md_end_clone_io
+    - bcache: fixup multi-threaded bch_sectors_dirty_init() wake-up race
+    - io_uring/fs: consider link->flags when getting path for LINKAT
+    - s390/dasd: protect device queue against concurrent access
+    - USB: serial: option: add Luat Air72*U series products
+    - hv_netvsc: Fix race of register_netdevice_notifier and VF register
+    - hv_netvsc: Mark VF as slave before exposing it to user-mode
+    - dm-delay: fix a race between delay_presuspend and delay_bio
+    - bcache: check return value from btree_node_alloc_replacement()
+    - bcache: prevent potential division by zero error
+    - bcache: fixup init dirty data errors
+    - bcache: fixup lock c->root error
+    - usb: cdnsp: Fix deadlock issue during using NCM gadget
+    - USB: serial: option: add Fibocom L7xx modules
+    - USB: serial: option: fix FM101R-GL defines
+    - USB: serial: option: don't claim interface 4 for ZTE MF290
+    - usb: typec: tcpm: Skip hard reset when in error recovery
+    - USB: dwc2: write HCINT with INTMASK applied
+    - usb: dwc3: Fix default mode initialization
+    - usb: dwc3: set the dma max_seg_size
+    - USB: dwc3: qcom: fix software node leak on probe errors
+    - USB: dwc3: qcom: fix wakeup after probe deferral
+    - io_uring: fix off-by one bvec index
+    - Linux 5.15.141
+  * Jammy update: v5.15.140 upstream stable release (LP: #2050038)
+    - locking/ww_mutex/test: Fix potential workqueue corruption
+    - perf/core: Bail out early if the request AUX area is out of bound
+    - clocksource/drivers/timer-imx-gpt: Fix potential memory leak
+    - clocksource/drivers/timer-atmel-tcb: Fix initialization on SAM9 hardware
+    - workqueue: Provide one lock class key per work_on_cpu() callsite
+    - x86/mm: Drop the 4 MB restriction on minimal NUMA node memory size
+    - wifi: mac80211_hwsim: fix clang-specific fortify warning
+    - wifi: mac80211: don't return unset power in ieee80211_get_tx_power()
+    - atl1c: Work around the DMA RX overflow issue
+    - bpf: Detect IP == ksym.end as part of BPF program
+    - wifi: ath9k: fix clang-specific fortify warnings
+    - wifi: ath10k: fix clang-specific fortify warning
+    - net: annotate data-races around sk->sk_tx_queue_mapping
+    - net: annotate data-races around sk->sk_dst_pending_confirm
+    - wifi: ath10k: Don't touch the CE interrupt registers after power up
+    - Bluetooth: btusb: Add date->evt_skb is NULL check
+    - Bluetooth: Fix double free in hci_conn_cleanup
+    - platform/x86: thinkpad_acpi: Add battery quirk for Thinkpad X120e
+    - drm/komeda: drop all currently held locks if deadlock happens
+    - drm/amdkfd: Fix a race condition of vram buffer unref in svm code
+    - drm/amd/display: use full update for clip size increase of large plane
+      source
+    - string.h: add array-wrappers for (v)memdup_user()
+    - kernel: kexec: copy user-array safely
+    - kernel: watch_queue: copy user-array safely
+    - drm: vmwgfx_surface.c: copy user-array safely
+    - drm/msm/dp: skip validity check for DP CTS EDID checksum
+    - drm/amd: Fix UBSAN array-index-out-of-bounds for SMU7
+    - drm/amd: Fix UBSAN array-index-out-of-bounds for Polaris and Tonga
+    - drm/amdgpu: Fix potential null pointer derefernce
+    - drm/panel: fix a possible null pointer dereference
+    - drm/panel/panel-tpo-tpg110: fix a possible null pointer dereference
+    - drm/amdgpu/vkms: fix a possible null pointer dereference
+    - drm/panel: st7703: Pick different reset sequence
+    - drm/amdkfd: Fix shift out-of-bounds issue
+    - drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL
+    - arm64: dts: ls208xa: use a pseudo-bus to constrain usb dma size
+    - selftests/efivarfs: create-read: fix a resource leak
+    - ASoC: soc-card: Add storage for PCI SSID
+    - crypto: pcrypt - Fix hungtask for PADATA_RESET
+    - RDMA/hfi1: Use FIELD_GET() to extract Link Width
+    - scsi: hisi_sas: Set debugfs_dir pointer to NULL after removing debugfs
+    - scsi: ibmvfc: Remove BUG_ON in the case of an empty event pool
+    - fs/jfs: Add check for negative db_l2nbperpage
+    - fs/jfs: Add validity check for db_maxag and db_agpref
+    - jfs: fix array-index-out-of-bounds in dbFindLeaf
+    - jfs: fix array-index-out-of-bounds in diAlloc
+    - HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround
+    - ARM: 9320/1: fix stack depot IRQ stack filter
+    - ALSA: hda: Fix possible null-ptr-deref when assigning a stream
+    - PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields
+    - atm: iphase: Do PCI error checks on own line
+    - scsi: libfc: Fix potential NULL pointer dereference in fc_lport_ptp_setup()
+    - PCI: Use FIELD_GET() to extract Link Width
+    - PCI: Extract ATS disabling to a helper function
+    - PCI: Disable ATS for specific Intel IPU E2000 devices
+    - misc: pci_endpoint_test: Add Device ID for R-Car S4-8 PCIe controller
+    - PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk
+    - HID: Add quirk for Dell Pro Wireless Keyboard and Mouse KM5221W
+    - exfat: support handle zero-size directory
+    - tty: vcc: Add check for kstrdup() in vcc_probe()
+    - usb: gadget: f_ncm: Always set current gadget in ncm_bind()
+    - 9p/trans_fd: Annotate data-racy writes to file::f_flags
+    - 9p: v9fs_listxattr: fix %s null argument warning
+    - i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
+    - i2c: sun6i-p2wi: Prevent potential division by zero
+    - virtio-blk: fix implicit overflow on virtio_max_dma_size
+    - i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
+    - media: gspca: cpia1: shift-out-of-bounds in set_flicker
+    - media: vivid: avoid integer overflow
+    - gfs2: ignore negated quota changes
+    - gfs2: fix an oops in gfs2_permission
+    - media: cobalt: Use FIELD_GET() to extract Link Width
+    - media: ccs: Fix driver quirk struct documentation
+    - media: imon: fix access to invalid resource for the second interface
+    - drm/amd/display: Avoid NULL dereference of timing generator
+    - kgdb: Flush console before entering kgdb on panic
+    - i2c: dev: copy userspace array safely
+    - ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
+    - drm/qxl: prevent memory leak
+    - drm/amdgpu: fix software pci_unplug on some chips
+    - pwm: Fix double shift bug
+    - wifi: iwlwifi: Use FW rate for non-data frames
+    - tracing: Reuse logic from perf's get_recursion_context()
+    - tracing/perf: Add interrupt_context_level() helper
+    - sched/core: Optimize in_task() and in_interrupt() a bit
+    - media: cadence: csi2rx: Unregister v4l2 async notifier
+    - media: cec: meson: always include meson sub-directory in Makefile
+    - SUNRPC: ECONNRESET might require a rebind
+    - SUNRPC: Add an IS_ERR() check back to where it was
+    - NFSv4.1: fix SP4_MACH_CRED protection for pnfs IO
+    - SUNRPC: Fix RPC client cleaned up the freed pipefs dentries
+    - gfs2: Silence "suspicious RCU usage in gfs2_permission" warning
+    - mptcp: diag: switch to context structure
+    - mptcp: listen diag dump support
+    - net: inet: Remove count from inet_listen_hashbucket
+    - net: inet: Open code inet_hash2 and inet_unhash2
+    - net: inet: Retire port only listening_hash
+    - net: set SOCK_RCU_FREE before inserting socket into hashtable
+    - ipvlan: add ipvlan_route_v6_outbound() helper
+    - tty: Fix uninit-value access in ppp_sync_receive()
+    - net: hns3: fix add VLAN fail issue
+    - net: hns3: refine the definition for struct hclge_pf_to_vf_msg
+    - net: hns3: add byte order conversion for PF to VF mailbox message
+    - net: hns3: add barrier in vf mailbox reply process
+    - net: hns3: fix incorrect capability bit display for copper port
+    - net: hns3: fix variable may not initialized problem in hns3_init_mac_addr()
+    - net: hns3: fix VF reset fail issue
+    - net: hns3: fix VF wrong speed and duplex issue
+    - tipc: Fix kernel-infoleak due to uninitialized TLV value
+    - ppp: limit MRU to 64K
+    - xen/events: fix delayed eoi list handling
+    - ptp: annotate data-race around q->head and q->tail
+    - bonding: stop the device in bond_setup_by_slave()
+    - net: ethernet: cortina: Fix max RX frame define
+    - net: ethernet: cortina: Handle large frames
+    - net: ethernet: cortina: Fix MTU max setting
+    - af_unix: fix use-after-free in unix_stream_read_actor()
+    - netfilter: nf_conntrack_bridge: initialize err to 0
+    - netfilter: nf_tables: use the correct get/put helpers
+    - netfilter: nf_tables: add and use BE register load-store helpers
+    - netfilter: nf_tables: fix pointer math issue in nft_byteorder_eval()
+    - net: stmmac: fix rx budget limit check
+    - net/mlx5e: Remove incorrect addition of action fwd flag
+    - net/mlx5e: Move mod hdr allocation to a single place
+    - net/mlx5e: Refactor mod header management API
+    - net/mlx5e: Fix pedit endianness
+    - net/mlx5e: Reduce the size of icosq_str
+    - net/mlx5e: Check return value of snprintf writing to fw_version buffer for
+      representors
+    - macvlan: Don't propagate promisc change to lower dev in passthru
+    - tools/power/turbostat: Fix a knl bug
+    - tools/power/turbostat: Enable the C-state Pre-wake printing
+    - cifs: spnego: add ';' in HOST_KEY_LEN
+    - cifs: fix check of rc in function generate_smb3signingkey
+    - xfs: refactor buffer cancellation table allocation
+    - xfs: don't leak xfs_buf_cancel structures when recovery fails
+    - xfs: convert buf_cancel_table allocation to kmalloc_array
+    - xfs: use invalidate_lock to check the state of mmap_lock
+    - xfs: prevent a UAF when log IO errors race with unmount
+    - xfs: flush inode gc workqueue before clearing agi bucket
+    - xfs: fix use-after-free in xattr node block inactivation
+    - xfs: don't leak memory when attr fork loading fails
+    - xfs: fix intermittent hang during quotacheck
+    - xfs: add missing cmap->br_state = XFS_EXT_NORM update
+    - xfs: Fix false ENOSPC when performing direct write on a delalloc extent in
+      cow fork
+    - xfs: fix inode reservation space for removing transaction
+    - xfs: avoid a UAF when log intent item recovery fails
+    - xfs: fix exception caused by unexpected illegal bestcount in leaf dir
+    - xfs: fix memory leak in xfs_errortag_init
+    - xfs: Fix unreferenced object reported by kmemleak in xfs_sysfs_init()
+    - i915/perf: Fix NULL deref bugs with drm_dbg() calls
+    - media: venus: hfi: add checks to perform sanity on queue pointers
+    - powerpc/perf: Fix disabling BHRB and instruction sampling
+    - randstruct: Fix gcc-plugin performance mode to stay in group
+    - bpf: Fix check_stack_write_fixed_off() to correctly spill imm
+    - bpf: Fix precision tracking for BPF_ALU | BPF_TO_BE | BPF_END
+    - scsi: mpt3sas: Fix loop logic
+    - scsi: megaraid_sas: Increase register read retry rount from 3 to 30 for
+      selected registers
+    - scsi: qla2xxx: Fix system crash due to bad pointer access
+    - crypto: x86/sha - load modules based on CPU features
+    - x86/cpu/hygon: Fix the CPU topology evaluation for real
+    - KVM: x86: hyper-v: Don't auto-enable stimer on write from user-space
+    - KVM: x86: Ignore MSR_AMD64_TW_CFG access
+    - audit: don't take task_lock() in audit_exe_compare() code path
+    - audit: don't WARN_ON_ONCE(!current->mm) in audit_exe_compare()
+    - tty/sysrq: replace smp_processor_id() with get_cpu()
+    - hvc/xen: fix console unplug
+    - hvc/xen: fix error path in xen_hvc_init() to always register frontend driver
+    - hvc/xen: fix event channel handling for secondary consoles
+    - PCI/sysfs: Protect driver's D3cold preference from user space
+    - watchdog: move softlockup_panic back to early_param
+    - ACPI: resource: Do IRQ override on TongFang GMxXGxx
+    - arm64: Restrict CPU_BIG_ENDIAN to GNU as or LLVM IAS 15.x or newer
+    - parisc/pdc: Add width field to struct pdc_model
+    - clk: socfpga: Fix undefined behavior bug in struct stratix10_clock_data
+    - clk: qcom: ipq8074: drop the CLK_SET_RATE_PARENT flag from PLL clocks
+    - clk: qcom: ipq6018: drop the CLK_SET_RATE_PARENT flag from PLL clocks
+    - mmc: vub300: fix an error code
+    - mmc: sdhci_am654: fix start loop index for TAP value parsing
+    - PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
+    - PCI: exynos: Don't discard .remove() callback
+    - wifi: wilc1000: use vmm_table as array in wilc struct
+    - svcrdma: Drop connection after an RDMA Read error
+    - rcu/tree: Defer setting of jiffies during stall reset
+    - arm64: dts: qcom: ipq6018: Fix hwlock index for SMEM
+    - PM: hibernate: Use __get_safe_page() rather than touching the list
+    - PM: hibernate: Clean up sync_read handling in snapshot_write_next()
+    - rcu: kmemleak: Ignore kmemleak false positives when RCU-freeing objects
+    - btrfs: don't arbitrarily slow down delalloc if we're committing
+    - firmware: qcom_scm: use 64-bit calling convention only when client is 64-bit
+    - ACPI: FPDT: properly handle invalid FPDT subtables
+    - ima: annotate iint mutex to avoid lockdep false positive warnings
+    - ima: detect changes to the backing overlay file
+    - wifi: ath11k: fix temperature event locking
+    - wifi: ath11k: fix dfs radar event locking
+    - wifi: ath11k: fix htt pktlog locking
+    - mmc: meson-gx: Remove setting of CMD_CFG_ERROR
+    - genirq/generic_chip: Make irq_remove_generic_chip() irqdomain aware
+    - KEYS: trusted: Rollback init_trusted() consistently
+    - PCI: keystone: Don't discard .remove() callback
+    - PCI: keystone: Don't discard .probe() callback
+    - netfilter: nf_tables: split async and sync catchall in two functions
+    - selftests/resctrl: Remove duplicate feature check from CMT test
+    - selftests/resctrl: Reduce failures due to outliers in MBA/MBM tests
+    - ASoC: codecs: wsa-macro: fix uninitialized stack variables with name prefix
+    - jbd2: fix potential data lost in recovering journal raced with synchronizing
+      fs bdev
+    - quota: explicitly forbid quota files from being encrypted
+    - kernel/reboot: emergency_restart: Set correct system_state
+    - i2c: core: Run atomic i2c xfer when !preemptible
+    - tracing: Have the user copy of synthetic event address use correct context
+    - mcb: fix error handling for different scenarios when parsing
+    - dmaengine: stm32-mdma: correct desc prep when channel running
+    - s390/cmma: fix detection of DAT pages
+    - mm/cma: use nth_page() in place of direct struct page manipulation
+    - mm/memory_hotplug: use pfn math in place of direct struct page manipulation
+    - mtd: cfi_cmdset_0001: Byte swap OTP info
+    - i3c: master: cdns: Fix reading status register
+    - i3c: master: svc: fix race condition in ibi work thread
+    - i3c: master: svc: fix wrong data return when IBI happen during start frame
+    - i3c: master: svc: fix ibi may not return mandatory data byte
+    - i3c: master: svc: fix check wrong status register in irq handler
+    - i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
+    - parisc: Prevent booting 64-bit kernels on PA1.x machines
+    - parisc/pgtable: Do not drop upper 5 address bits of physical address
+    - xhci: Enable RPM on controllers that support low-power states
+    - ALSA: info: Fix potential deadlock at disconnection
+    - ALSA: hda/realtek - Add Dell ALC295 to pin fall back table
+    - ALSA: hda/realtek - Enable internal speaker of ASUS K6500ZC
+    - serial: meson: Use platform_get_irq() to get the interrupt
+    - tty: serial: meson: fix hard LOCKUP on crtscts mode
+    - regmap: Ensure range selector registers are updated after cache sync
+    - cpufreq: stats: Fix buffer overflow detection in trans_stats()
+    - Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0cb8:0xc559
+    - bluetooth: Add device 0bda:887b to device tables
+    - bluetooth: Add device 13d3:3571 to device tables
+    - Bluetooth: btusb: Add RTW8852BE device 13d3:3570 to device tables
+    - Bluetooth: btusb: Add 0bda:b85b for Fn-Link RTL8852BE
+    - ksmbd: fix slab out of bounds write in smb_inherit_dacl()
+    - arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
+    - arm64: dts: qcom: ipq6018: Fix tcsr_mutex register size
+    - powerpc/pseries/ddw: simplify enable_ddw()
+    - Revert ncsi: Propagate carrier gain/loss events to the NCSI controller
+    - Revert "i2c: pxa: move to generic GPIO recovery"
+    - lsm: fix default return value for vm_enough_memory
+    - lsm: fix default return value for inode_getsecctx
+    - sbsa_gwdt: Calculate timeout with 64-bit math
+    - i2c: designware: Disable TX_EMPTY irq while waiting for block length byte
+    - s390/ap: fix AP bus crash on early config change callback invocation
+    - net: ethtool: Fix documentation of ethtool_sprintf()
+    - net: dsa: lan9303: consequently nested-lock physical MDIO
+    - net: phylink: initialize carrier state at creation
+    - i2c: i801: fix potential race in i801_block_transaction_byte_by_byte
+    - f2fs: avoid format-overflow warning
+    - media: lirc: drop trailing space from scancode transmit
+    - media: sharp: fix sharp encoding
+    - media: venus: hfi_parser: Add check to keep the number of codecs within
+      range
+    - media: venus: hfi: fix the check to handle session buffer requirement
+    - media: venus: hfi: add checks to handle capabilities from firmware
+    - media: ccs: Correctly initialise try compose rectangle
+    - nfsd: fix file memleak on client_opens_release
+    - riscv: kprobes: allow writing to x0
+    - mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2
+    - mm: kmem: drop __GFP_NOFAIL when allocating objcg vectors
+    - r8169: fix network lost after resume on DASH systems
+    - mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of AER
+    - media: qcom: camss: Fix pm_domain_on sequence in probe
+    - media: qcom: camss: Fix vfe_get() error jump
+    - media: qcom: camss: Fix VFE-17x vfe_disable_output()
+    - media: qcom: camss: Fix missing vfe_lite clocks check
+    - ext4: apply umask if ACL support is disabled
+    - ext4: correct offset of gdb backup in non meta_bg group to update_backups
+    - ext4: correct return value of ext4_convert_meta_bg
+    - ext4: correct the start block of counting reserved clusters
+    - ext4: remove gdb backup copy for meta bg in setup_new_flex_group_blocks
+    - ext4: add missed brelse in update_backups
+    - drm/amd/pm: Handle non-terminated overdrive commands.
+    - drm/i915: Fix potential spectre vulnerability
+    - drm/amdgpu: don't use ATRM for external devices
+    - drm/amdgpu: fix error handling in amdgpu_bo_list_get()
+    - drm/amd/display: Change the DMCUB mailbox memory location from FB to inbox
+    - powerpc/powernv: Fix fortify source warnings in opal-prd.c
+    - tracing: Have trace_event_file have ref counters
+    - Input: xpad - add VID for Turtle Beach controllers
+    - driver core: Release all resources during unbind before updating device
+      links
+    - Linux 5.15.140
+  * CVE-2023-46862
+    - io_uring/fdinfo: lock SQ thread while retrieving thread cpu/pid
+  * Jammy update: v5.15.139 upstream stable release (LP: #2049432)
+    - iov_iter, x86: Be consistent about the __user tag on copy_mc_to_user()
+    - sched/uclamp: Ignore (util == 0) optimization in feec() when p_util_max = 0
+    - sched: Fix stop_one_cpu_nowait() vs hotplug
+    - vfs: fix readahead(2) on block devices
+    - writeback, cgroup: switch inodes with dirty timestamps to release dying
+      cgwbs
+    - x86/srso: Fix SBPB enablement for (possible) future fixed HW
+    - futex: Don't include process MM in futex key on no-MMU
+    - x86: Share definition of __is_canonical_address()
+    - x86/sev-es: Allow copy_from_kernel_nofault() in earlier boot
+    - x86/boot: Fix incorrect startup_gdt_descr.size
+    - pstore/platform: Add check for kstrdup
+    - genirq/matrix: Exclude managed interrupts in irq_matrix_allocated()
+    - i40e: fix potential memory leaks in i40e_remove()
+    - selftests/bpf: Test tail call counting with bpf2bpf and data on stack
+    - selftests/bpf: Correct map_fd to data_fd in tailcalls
+    - udp: add missing WRITE_ONCE() around up->encap_rcv
+    - tcp: call tcp_try_undo_recovery when an RTOd TFO SYNACK is ACKed
+    - gve: Use size_add() in call to struct_size()
+    - mlxsw: Use size_mul() in call to struct_size()
+    - tipc: Use size_add() in calls to struct_size()
+    - net: spider_net: Use size_add() in call to struct_size()
+    - wifi: rtw88: debug: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
+    - wifi: mt76: mt7603: rework/fix rx pse hang check
+    - mt76: dma: use kzalloc instead of devm_kzalloc for txwi
+    - mt76: add support for overriding the device used for DMA mapping
+    - mt76: pass original queue id from __mt76_tx_queue_skb to the driver
+    - wifi: mt76: mt7603: improve stuck beacon handling
+    - tcp_metrics: add missing barriers on delete
+    - tcp_metrics: properly set tp->snd_ssthresh in tcp_init_metrics()
+    - tcp_metrics: do not create an entry from tcp_init_metrics()
+    - wifi: rtlwifi: fix EDCA limit set by BT coexistence
+    - can: dev: can_restart(): don't crash kernel if carrier is OK
+    - can: dev: can_restart(): fix race condition between controller restart and
+      netif_carrier_on()
+    - can: dev: can_put_echo_skb(): don't crash kernel if can_priv::echo_skb is
+      accessed out of bounds
+    - PM / devfreq: rockchip-dfi: Make pmu regmap mandatory
+    - netfilter: nf_tables: Drop pointless memset when dumping rules
+    - thermal: core: prevent potential string overflow
+    - r8169: use tp_to_dev instead of open code
+    - r8169: fix rare issue with broken rx after link-down on RTL8125
+    - chtls: fix tp->rcv_tstamp initialization
+    - tcp: fix cookie_init_timestamp() overflows
+    - iwlwifi: pcie: adjust to Bz completion descriptor
+    - wifi: iwlwifi: call napi_synchronize() before freeing rx/tx queues
+    - wifi: iwlwifi: pcie: synchronize IRQs before NAPI
+    - wifi: iwlwifi: empty overflow queue during flush
+    - ACPI: sysfs: Fix create_pnp_modalias() and create_of_modalias()
+    - ipv6: avoid atomic fragment on GSO packets
+    - net: add DEV_STATS_READ() helper
+    - ipvlan: properly track tx_errors
+    - regmap: debugfs: Fix a erroneous check after snprintf()
+    - spi: tegra: Fix missing IRQ check in tegra_slink_probe()
+    - clk: qcom: clk-rcg2: Fix clock rate overflow for high parent frequencies
+    - clk: qcom: mmcc-msm8998: Don't check halt bit on some branch clks
+    - clk: qcom: mmcc-msm8998: Fix the SMMU GDSC
+    - clk: qcom: gcc-sm8150: Fix gcc_sdcc2_apps_clk_src
+    - clk: imx: Select MXC_CLK for CLK_IMX8QXP
+    - clk: imx: imx8mq: correct error handling path
+    - clk: imx: imx8qxp: Fix elcdif_pll clock
+    - clk: renesas: rzg2l: Simplify multiplication/shift logic
+    - clk: renesas: rzg2l: Use FIELD_GET() for PLL register fields
+    - clk: renesas: rzg2l: Fix computation formula
+    - spi: nxp-fspi: use the correct ioremap function
+    - clk: keystone: pll: fix a couple NULL vs IS_ERR() checks
+    - clk: ti: Add ti_dt_clk_name() helper to use clock-output-names
+    - clk: ti: Update pll and clockdomain clocks to use ti_dt_clk_name()
+    - clk: ti: Update component clocks to use ti_dt_clk_name()
+    - clk: ti: change ti_clk_register[_omap_hw]() API
+    - clk: ti: fix double free in of_ti_divider_clk_setup()
+    - clk: npcm7xx: Fix incorrect kfree
+    - clk: mediatek: clk-mt6765: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt6797: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt7629-eth: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt7629: Add check for mtk_alloc_clk_data
+    - clk: mediatek: clk-mt2701: Add check for mtk_alloc_clk_data
+    - clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM
+    - platform/x86: wmi: Fix probe failure when failing to register WMI devices
+    - platform/x86: wmi: remove unnecessary initializations
+    - platform/x86: wmi: Fix opening of char device
+    - hwmon: (axi-fan-control) Fix possible NULL pointer dereference
+    - hwmon: (coretemp) Fix potentially truncated sysfs attribute name
+    - drm/rockchip: vop: Fix reset of state in duplicate state crtc funcs
+    - drm/rockchip: vop: Fix call to crtc reset helper
+    - drm/radeon: possible buffer overflow
+    - drm/mipi-dsi: Create devm device registration
+    - drm/mipi-dsi: Create devm device attachment
+    - drm/bridge: lt8912b: Switch to devm MIPI-DSI helpers
+    - drm/bridge: lt8912b: Register and attach our DSI device at probe
+    - drm/bridge: lt8912b: Add hot plug detection
+    - drm/bridge: lt8912b: Fix bridge_detach
+    - drm/bridge: lt8912b: Fix crash on bridge detach
+    - drm/bridge: lt8912b: Manually disable HPD only if it was enabled
+    - drm/bridge: lt8912b: Add missing drm_bridge_attach call
+    - drm/bridge: tc358768: Fix use of uninitialized variable
+    - drm/bridge: tc358768: Disable non-continuous clock mode
+    - drm/bridge: tc358768: Fix bit updates
+    - drm/amdkfd: fix some race conditions in vram buffer alloc/free of svm code
+    - drm/mediatek: Fix iommu fault by swapping FBs after updating plane state
+    - drm/mediatek: Fix iommu fault during crtc enabling
+    - drm/rockchip: cdn-dp: Fix some error handling paths in cdn_dp_probe()
+    - arm64/arm: xen: enlighten: Fix KPTI checks
+    - drm/rockchip: Fix type promotion bug in rockchip_gem_iommu_map()
+    - xen-pciback: Consider INTx disabled when MSI/MSI-X is enabled
+    - drm/msm/dsi: use msm_gem_kernel_put to free TX buffer
+    - drm: mediatek: mtk_dsi: Fix NO_EOT_PACKET settings/handling
+    - perf: hisi: Fix use-after-free when register pmu fails
+    - ARM: dts: renesas: blanche: Fix typo in GP_11_2 pin name
+    - arm64: dts: qcom: msm8916: Fix iommu local address range
+    - arm64: dts: qcom: msm8992-libra: drop duplicated reserved memory
+    - arm64: dts: qcom: sc7280: Add missing LMH interrupts
+    - arm64: dts: qcom: sdm845-mtp: fix WiFi configuration
+    - ARM64: dts: marvell: cn9310: Use appropriate label for spi1 pins
+    - arm64: dts: qcom: apq8016-sbc: Add missing ADV7533 regulators
+    - ARM: dts: qcom: mdm9615: populate vsdcc fixed regulator
+    - soc: qcom: llcc: Handle a second device without data corruption
+    - firmware: ti_sci: Mark driver as non removable
+    - firmware: arm_ffa: Assign the missing IDR allocation ID to the FFA device
+    - clk: scmi: Free scmi_clk allocated when the clocks with invalid info are
+      skipped
+    - arm64: dts: imx8qm-ss-img: Fix jpegenc compatible entry
+    - arm64: dts: imx8mm: Add sound-dai-cells to micfil node
+    - arm64: dts: imx8mn: Add sound-dai-cells to micfil node
+    - selftests/pidfd: Fix ksft print formats
+    - selftests/resctrl: Ensure the benchmark commands fits to its array
+    - crypto: hisilicon/hpre - Fix a erroneous check after snprintf()
+    - hwrng: geode - fix accessing registers
+    - RDMA/core: Use size_{add,sub,mul}() in calls to struct_size()
+    - scsi: ibmvfc: Fix erroneous use of rtas_busy_delay with hcall return code
+    - libnvdimm/of_pmem: Use devm_kstrdup instead of kstrdup and check its return
+      value
+    - nd_btt: Make BTT lanes preemptible
+    - crypto: caam/qi2 - fix Chacha20 + Poly1305 self test failure
+    - crypto: caam/jr - fix Chacha20 + Poly1305 self test failure
+    - crypto: qat - increase size of buffers
+    - hid: cp2112: Fix duplicate workqueue initialization
+    - ARM: 9321/1: memset: cast the constant byte to unsigned char
+    - ext4: move 'ix' sanity check to corrent position
+    - ASoC: fsl: mpc5200_dma.c: Fix warning of Function parameter or member not
+      described
+    - IB/mlx5: Fix rdma counter binding for RAW QP
+    - RDMA/hns: Fix uninitialized ucmd in hns_roce_create_qp_common()
+    - RDMA/hns: Fix signed-unsigned mixed comparisons
+    - RDMA/hns: The UD mode can only be configured with DCQCN
+    - ASoC: fsl: Fix PM disable depth imbalance in fsl_easrc_probe
+    - scsi: ufs: core: Leave space for '\0' in utf8 desc string
+    - RDMA/hfi1: Workaround truncation compilation error
+    - hid: cp2112: Fix IRQ shutdown stopping polling for all IRQs on chip
+    - sh: bios: Revive earlyprintk support
+    - Revert "HID: logitech-hidpp: add a module parameter to keep firmware
+      gestures"
+    - HID: logitech-hidpp: Remove HIDPP_QUIRK_NO_HIDINPUT quirk
+    - HID: logitech-hidpp: Don't restart IO, instead defer hid_connect() only
+    - HID: logitech-hidpp: Revert "Don't restart communication if not necessary"
+    - HID: logitech-hidpp: Move get_wireless_feature_index() check to
+      hidpp_connect_event()
+    - ASoC: Intel: Skylake: Fix mem leak when parsing UUIDs fails
+    - padata: Fix refcnt handling in padata_free_shell()
+    - crypto: qat - fix deadlock in backlog processing
+    - ASoC: ams-delta.c: use component after check
+    - mfd: core: Un-constify mfd_cell.of_reg
+    - mfd: core: Ensure disabled devices are skipped without aborting
+    - mfd: dln2: Fix double put in dln2_probe
+    - mfd: arizona-spi: Set pdata.hpdet_channel for ACPI enumerated devs
+    - leds: turris-omnia: Drop unnecessary mutex locking
+    - leds: turris-omnia: Do not use SMBUS calls
+    - leds: pwm: Don't disable the PWM when the LED should be off
+    - leds: trigger: ledtrig-cpu:: Fix 'output may be truncated' issue for 'cpu'
+    - f2fs: compress: fix to avoid use-after-free on dic
+    - f2fs: compress: fix to avoid redundant compress extension
+    - tty: tty_jobctrl: fix pid memleak in disassociate_ctty()
+    - livepatch: Fix missing newline character in klp_resolve_symbols()
+    - dmaengine: idxd: Register dsa_bus_type before registering idxd sub-drivers
+    - usb: dwc2: fix possible NULL pointer dereference caused by driver
+      concurrency
+    - usb: chipidea: Fix DMA overwrite for Tegra
+    - usb: chipidea: Simplify Tegra DMA alignment code
+    - dmaengine: ti: edma: handle irq_of_parse_and_map() errors
+    - misc: st_core: Do not call kfree_skb() under spin_lock_irqsave()
+    - tools: iio: iio_generic_buffer ensure alignment
+    - USB: usbip: fix stub_dev hub disconnect
+    - dmaengine: pxa_dma: Remove an erroneous BUG_ON() in pxad_free_desc()
+    - f2fs: fix to initialize map.m_pblk in f2fs_precache_extents()
+    - powerpc: Only define __parse_fpscr() when required
+    - modpost: fix tee MODULE_DEVICE_TABLE built on big-endian host
+    - powerpc/40x: Remove stale PTE_ATOMIC_UPDATES macro
+    - powerpc/xive: Fix endian conversion size
+    - powerpc/imc-pmu: Use the correct spinlock initializer.
+    - powerpc/pseries: fix potential memory leak in init_cpu_associativity()
+    - usb: host: xhci-plat: fix possible kernel oops while resuming
+    - perf machine: Avoid out of bounds LBR memory read
+    - perf hist: Add missing puts to hist__account_cycles
+    - 9p/net: fix possible memory leak in p9_check_errors()
+    - i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
+    - cxl/mem: Fix shutdown order
+    - rtc: pcf85363: fix wrong mask/val parameters in regmap_update_bits call
+    - pcmcia: cs: fix possible hung task and memory leak pccardd()
+    - pcmcia: ds: fix refcount leak in pcmcia_device_add()
+    - pcmcia: ds: fix possible name leak in error path in pcmcia_device_add()
+    - media: i2c: max9286: Fix some redundant of_node_put() calls
+    - media: bttv: fix use after free error due to btv->timeout timer
+    - media: s3c-camif: Avoid inappropriate kfree()
+    - media: vidtv: psi: Add check for kstrdup
+    - media: vidtv: mux: Add check and kfree for kstrdup
+    - media: cedrus: Fix clock/reset sequence
+    - media: dvb-usb-v2: af9035: fix missing unlock
+    - regmap: prevent noinc writes from clobbering cache
+    - pwm: sti: Reduce number of allocations and drop usage of chip_data
+    - pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
+    - Input: synaptics-rmi4 - fix use after free in rmi_unregister_function()
+    - llc: verify mac len before reading mac header
+    - hsr: Prevent use after free in prp_create_tagged_frame()
+    - tipc: Change nla_policy for bearer-related names to NLA_NUL_STRING
+    - bpf: Check map->usercnt after timer->timer is assigned
+    - inet: shrink struct flowi_common
+    - octeontx2-pf: Fix error codes
+    - octeontx2-pf: Fix holes in error code
+    - dccp: Call security_inet_conn_request() after setting IPv4 addresses.
+    - dccp/tcp: Call security_inet_conn_request() after setting IPv6 addresses.
+    - Fix termination state for idr_for_each_entry_ul()
+    - net: stmmac: xgmac: Enable support for multiple Flexible PPS outputs
+    - selftests: pmtu.sh: fix result checking
+    - net/smc: fix dangling sock under state SMC_APPFINCLOSEWAIT
+    - net/smc: allow cdc msg send rather than drop it with NULL sndbuf_desc
+    - net/smc: put sk reference if close work was canceled
+    - tg3: power down device only on SYSTEM_POWER_OFF
+    - block: remove unneeded return value of bio_check_ro()
+    - blk-core: use pr_warn_ratelimited() in bio_check_ro()
+    - r8169: respect userspace disabling IFF_MULTICAST
+    - i2c: iproc: handle invalid slave state
+    - netfilter: xt_recent: fix (increase) ipv6 literal buffer length
+    - netfilter: nft_redir: use `struct nf_nat_range2` throughout and deduplicate
+      eval call-backs
+    - netfilter: nat: fix ipv6 nat redirect with mapped and scoped addresses
+    - drm/syncobj: fix DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE
+    - ASoC: hdmi-codec: register hpd callback on component probe
+    - spi: spi-zynq-qspi: add spi-mem to driver kconfig dependencies
+    - fbdev: imsttfb: Fix error path of imsttfb_probe()
+    - fbdev: imsttfb: fix a resource leak in probe
+    - fbdev: fsl-diu-fb: mark wr_reg_wa() static
+    - tracing/kprobes: Fix the order of argument descriptions
+    - btrfs: use u64 for buffer sizes in the tree search ioctls
+    - Linux 5.15.139
+  * Jammy update: v5.15.138 upstream stable release (LP: #2049417)
+    - ASoC: codecs: wcd938x: fix resource leaks on bind errors
+    - ASoC: codecs: wcd938x: fix runtime PM imbalance on remove
+    - pinctrl: qcom: lpass-lpi: fix concurrent register updates
+    - tcp: remove dead code from tcp_sendmsg_locked()
+    - tcp: cleanup tcp_remove_empty_skb() use
+    - mptcp: more conservative check for zero probes
+    - mcb: Return actual parsed size when reading chameleon table
+    - mcb-lpc: Reallocate memory region to avoid memory overlapping
+    - virtio_balloon: Fix endless deflation and inflation on arm64
+    - virtio-mmio: fix memory leak of vm_dev
+    - vhost: Allow null msg.size on VHOST_IOTLB_INVALIDATE
+    - mm/page_alloc: correct start page when guard page debug is enabled
+    - mm/migrate: fix do_pages_move for compat pointers
+    - nfsd: lock_rename() needs both directories to live on the same fs
+    - drm/i915/pmu: Check if pmu is closed before stopping event
+    - vsock/virtio: factor our the code to initialize and delete VQs
+    - vsock/virtio: add support for device suspend/resume
+    - vsock/virtio: initialize the_virtio_vsock before using VQs
+    - drm/dp_mst: Fix NULL deref in get_mst_branch_device_by_guid_helper()
+    - firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels()
+    - r8169: fix the KCSAN reported data-race in rtl_tx() while reading tp->cur_tx
+    - r8169: fix the KCSAN reported data-race in rtl_tx while reading
+      TxDescArray[entry].opts1
+    - r8169: fix the KCSAN reported data race in rtl_rx while reading desc->opts1
+    - i40e: Fix I40E_FLAG_VF_VLAN_PRUNING value
+    - treewide: Spelling fix in comment
+    - igb: Fix potential memory leak in igb_add_ethtool_nfc_entry
+    - neighbour: fix various data-races
+    - igc: Fix ambiguity in the ethtool advertising
+    - net: ieee802154: adf7242: Fix some potential buffer overflow in
+      adf7242_stats_show()
+    - net: usb: smsc95xx: Fix uninit-value access in smsc95xx_read_reg
+    - r8152: Increase USB control msg timeout to 5000ms as per spec
+    - r8152: Run the unload routine if we have errors during probe
+    - r8152: Cancel hw_phy_work if we have an error in probe
+    - r8152: Release firmware if we have an error in probe
+    - tcp: fix wrong RTO timeout when received SACK reneging
+    - gtp: uapi: fix GTPA_MAX
+    - gtp: fix fragmentation needed check with gso
+    - i40e: Fix wrong check for I40E_TXR_FLAGS_WB_ON_ITR
+    - kasan: print the original fault addr when access invalid shadow
+    - iio: exynos-adc: request second interupt only when touchscreen mode is used
+    - iio: adc: xilinx-xadc: Don't clobber preset voltage/temperature thresholds
+    - iio: adc: xilinx-xadc: Correct temperature offset/scale for UltraScale
+    - i2c: muxes: i2c-mux-pinctrl: Use of_get_i2c_adapter_by_node()
+    - i2c: muxes: i2c-mux-gpmux: Use of_get_i2c_adapter_by_node()
+    - i2c: muxes: i2c-demux-pinctrl: Use of_get_i2c_adapter_by_node()
+    - i2c: stm32f7: Fix PEC handling in case of SMBUS transfers
+    - i2c: aspeed: Fix i2c bus hang in slave read
+    - tracing/kprobes: Fix the description of variable length arguments
+    - misc: fastrpc: Clean buffers on remote invocation failures
+    - nvmem: imx: correct nregs for i.MX6ULL
+    - nvmem: imx: correct nregs for i.MX6SLL
+    - nvmem: imx: correct nregs for i.MX6UL
+    - perf/core: Fix potential NULL deref
+    - sparc32: fix a braino in fault handling in csum_and_copy_..._user()
+    - clk: Sanitize possible_parent_show to Handle Return Value of
+      of_clk_get_parent_name
+    - iio: afe: rescale: reorder includes
+    - iio: afe: rescale: expose scale processing function
+    - iio: afe: rescale: add offset support
+    - iio: afe: rescale: Accept only offset channels
+    - gve: Fix GFP flags when allocing pages
+    - x86/i8259: Skip probing when ACPI/MADT advertises PCAT compatibility
+    - x86/mm: Simplify RESERVE_BRK()
+    - x86/mm: Fix RESERVE_BRK() for older binutils
+    - ext4: add two helper functions extent_logical_end() and pa_logical_end()
+    - ext4: fix BUG in ext4_mb_new_inode_pa() due to overflow
+    - ext4: avoid overlapping preallocations due to overflow
+    - objtool/x86: add missing embedded_insn check
+    - driver: platform: Add helper for safer setting of driver_override
+    - rpmsg: Constify local variable in field store macro
+    - rpmsg: Fix kfree() of static memory on setting driver_override
+    - rpmsg: Fix calling device_lock() on non-initialized device
+    - rpmsg: glink: Release driver_override
+    - rpmsg: Fix possible refcount leak in rpmsg_register_device_override()
+    - x86: Fix .brk attribute in linker script
+    - ASoC: simple-card: fixup asoc_simple_probe() error handling
+    - net: sched: cls_u32: Fix allocation size in u32_init()
+    - irqchip/riscv-intc: Mark all INTC nodes as initialized
+    - irqchip/stm32-exti: add missing DT IRQ flag translation
+    - dmaengine: ste_dma40: Fix PM disable depth imbalance in d40_probe
+    - powerpc/85xx: Fix math emulation exception
+    - Input: synaptics-rmi4 - handle reset delay when using SMBus trsnsport
+    - fbdev: atyfb: only use ioremap_uc() on i386 and ia64
+    - fs/ntfs3: Add ckeck in ni_update_parent()
+    - fs/ntfs3: Write immediately updated ntfs state
+    - fs/ntfs3: Use kvmalloc instead of kmalloc(... __GFP_NOWARN)
+    - fs/ntfs3: Fix possible NULL-ptr-deref in ni_readpage_cmpr()
+    - fs/ntfs3: Fix NULL pointer dereference on error in attr_allocate_frame()
+    - fs/ntfs3: Fix directory element type detection
+    - fs/ntfs3: Avoid possible memory leak
+    - spi: npcm-fiu: Fix UMA reads when dummy.nbytes == 0
+    - netfilter: nfnetlink_log: silence bogus compiler warning
+    - ASoC: rt5650: fix the wrong result of key button
+    - drm/ttm: Reorder sys manager cleanup step
+    - fbdev: uvesafb: Call cn_del_callback() at the end of uvesafb_exit()
+    - scsi: mpt3sas: Fix in error path
+    - platform/mellanox: mlxbf-tmfifo: Fix a warning message
+    - net: chelsio: cxgb4: add an error code check in t4_load_phy_fw
+    - r8152: Check for unplug in rtl_phy_patch_request()
+    - r8152: Check for unplug in r8153b_ups_en() / r8153c_ups_en()
+    - powerpc/mm: Fix boot crash with FLATMEM
+    - can: isotp: set max PDU size to 64 kByte
+    - can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
+    - can: isotp: check CAN address family in isotp_bind()
+    - can: isotp: handle wait_event_interruptible() return values
+    - can: isotp: add local echo tx processing and tx without FC
+    - can: isotp: isotp_bind(): do not validate unused address information
+    - can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior
+    - drm/amd: Move helper for dynamic speed switch check out of smu13
+    - drm/amd: Disable ASPM for VI w/ all Intel systems
+    - PCI: Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device
+    - usb: storage: set 1.50 as the lower bcdDevice for older "Super Top"
+      compatibility
+    - usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
+    - usb: raw-gadget: properly handle interrupted requests
+    - tty: n_gsm: fix race condition in status line change on dead connections
+    - tty: 8250: Remove UC-257 and UC-431
+    - tty: 8250: Add support for additional Brainboxes UC cards
+    - tty: 8250: Add support for Brainboxes UP cards
+    - tty: 8250: Add support for Intashield IS-100
+    - tty: 8250: Fix port count of PX-257
+    - tty: 8250: Fix up PX-803/PX-857
+    - tty: 8250: Add support for additional Brainboxes PX cards
+    - tty: 8250: Add support for Intashield IX cards
+    - tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
+    - misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
+    - ALSA: hda: intel-dsp-config: Fix JSL Chromebook quirk detection
+    - Linux 5.15.138
+  * Jammy update: v5.15.137 upstream stable release (LP: #2049350)
+    - lib/Kconfig.debug: do not enable DEBUG_PREEMPT by default
+    - Documentation: sysctl: align cells in second content column
+    - xfs: don't expose internal symlink metadata buffers to the vfs
+    - Bluetooth: hci_event: Ignore NULL link key
+    - Bluetooth: Reject connection with the device which has same BD_ADDR
+    - Bluetooth: Fix a refcnt underflow problem for hci_conn
+    - Bluetooth: vhci: Fix race when opening vhci device
+    - Bluetooth: hci_event: Fix coding style
+    - Bluetooth: avoid memcmp() out of bounds warning
+    - ice: fix over-shifted variable
+    - ice: reset first in crash dump kernels
+    - nfc: nci: fix possible NULL pointer dereference in send_acknowledge()
+    - regmap: fix NULL deref on lookup
+    - KVM: x86: Mask LVTPC when handling a PMI
+    - tcp: check mptcp-level constraints for backlog coalescing
+    - fs/ntfs3: Fix possible null-pointer dereference in hdr_find_e()
+    - fs/ntfs3: fix panic about slab-out-of-bounds caused by ntfs_list_ea()
+    - fs/ntfs3: fix deadlock in mark_as_free_ex
+    - netfilter: nft_payload: fix wrong mac header matching
+    - drm/i915: Retry gtt fault when out of fence registers
+    - ASoC: codecs: wcd938x-sdw: fix use after free on driver unbind
+    - ASoC: codecs: wcd938x-sdw: fix runtime PM imbalance on probe errors
+    - ASoC: codecs: wcd938x: drop bogus bind error handling
+    - ASoC: codecs: wcd938x: fix unbind tear down order
+    - qed: fix LL2 RX buffer allocation
+    - xfrm: fix a data-race in xfrm_gen_index()
+    - xfrm: interface: use DEV_STATS_INC()
+    - net: ipv4: fix return value check in esp_remove_trailer
+    - net: ipv6: fix return value check in esp_remove_trailer
+    - net: rfkill: gpio: prevent value glitch during probe
+    - tcp: fix excessive TLP and RACK timeouts from HZ rounding
+    - tcp: tsq: relax tcp_small_queue_check() when rtx queue contains a single skb
+    - tun: prevent negative ifindex
+    - ipv4: fib: annotate races around nh->nh_saddr_genid and nh->nh_saddr
+    - net: usb: smsc95xx: Fix an error code in smsc95xx_reset()
+    - i40e: prevent crash on probe if hw registers have invalid values
+    - net: dsa: bcm_sf2: Fix possible memory leak in bcm_sf2_mdio_register()
+    - bonding: Return pointer to data after pull on skb
+    - net/sched: sch_hfsc: upgrade 'rt' to 'sc' when it becomes a inner curve
+    - neighbor: tracing: Move pin6 inside CONFIG_IPV6=y section
+    - netfilter: nft_set_rbtree: .deactivate fails if element has expired
+    - netfilter: nf_tables: do not remove elements if set backend implements
+      .abort
+    - netfilter: nf_tables: revert do not remove elements if set backend
+      implements .abort
+    - net: pktgen: Fix interface flags printing
+    - selftests/mm: fix awk usage in charge_reserved_hugetlb.sh and
+      hugetlb_reparenting_test.sh that may cause error
+    - serial: 8250: omap: Fix imprecise external abort for omap_8250_pm()
+    - serial: 8250_omap: Fix errors with no_console_suspend
+    - iio: Un-inline iio_buffer_enabled()
+    - iio: core: Hide read accesses to iio_dev->currentmode
+    - iio: core: introduce iio_device_{claim|release}_buffer_mode() APIs
+    - iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
+    - iio: adc: ad7192: Correct reference voltage
+    - perf: Add irq and exception return branch types
+    - perf/x86: Move branch classifier
+    - perf/x86/lbr: Filter vsyscall addresses
+    - drm/atomic-helper: relax unregistered connector check
+    - powerpc/32s: Remove capability to disable KUEP at boottime
+    - powerpc/32s: Do kuep_lock() and kuep_unlock() in assembly
+    - powerpc/47x: Fix 47x syscall return crash
+    - mctp: Allow local delivery to the null EID
+    - mctp: perform route lookups under a RCU read-side lock
+    - nfp: flower: avoid rmmod nfp crash issues
+    - ksmbd: not allow to open file if delelete on close bit is set
+    - ARM: dts: ti: omap: Fix noisy serial with overrun-throttle-ms for mapphone
+    - fs-writeback: do not requeue a clean inode having skipped pages
+    - btrfs: return -EUCLEAN for delayed tree ref with a ref count not equals to 1
+    - btrfs: initialize start_slot in btrfs_log_prealloc_extents
+    - i2c: mux: Avoid potential false error message in i2c_mux_add_adapter
+    - overlayfs: set ctime when setting mtime and atime
+    - gpio: timberdale: Fix potential deadlock on &tgpio->lock
+    - ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
+    - ata: libata-eh: Fix compilation warning in ata_eh_link_report()
+    - tracing: relax trace_event_eval_update() execution with cond_resched()
+    - wifi: mwifiex: Sanity check tlv_len and tlv_bitmap_len
+    - wifi: iwlwifi: Ensure ack flag is properly cleared.
+    - HID: holtek: fix slab-out-of-bounds Write in holtek_kbd_input_event
+    - Bluetooth: btusb: add shutdown function for QCA6174
+    - Bluetooth: Avoid redundant authentication
+    - Bluetooth: hci_core: Fix build warnings
+    - wifi: cfg80211: Fix 6GHz scan configuration
+    - wifi: mac80211: allow transmitting EAPOL frames with tainted key
+    - wifi: cfg80211: avoid leaking stack data into trace
+    - regulator/core: Revert "fix kobject release warning and memory leak in
+      regulator_register()"
+    - sky2: Make sure there is at least one frag_addr available
+    - ipv4/fib: send notify when delete source address routes
+    - drm: panel-orientation-quirks: Add quirk for One Mix 2S
+    - btrfs: fix some -Wmaybe-uninitialized warnings in ioctl.c
+    - btrfs: error out when COWing block using a stale transaction
+    - btrfs: error when COWing block from a root that is being deleted
+    - btrfs: error out when reallocating block for defrag using a stale
+      transaction
+    - HID: multitouch: Add required quirk for Synaptics 0xcd7e device
+    - platform/x86: touchscreen_dmi: Add info for the Positivo C4128B
+    - net/mlx5: Handle fw tracer change ownership event based on MTRC
+    - Bluetooth: hci_event: Fix using memcmp when comparing keys
+    - net: introduce a function to check if a netdev name is in use
+    - net: move from strlcpy with unused retval to strscpy
+    - net: fix ifname in netlink ntf during netns move
+    - mtd: rawnand: qcom: Unmap the right resource upon probe failure
+    - mtd: rawnand: pl353: Ensure program page operations are successful
+    - mtd: rawnand: marvell: Ensure program page operations are successful
+    - mtd: rawnand: arasan: Ensure program page operations are successful
+    - mtd: spinand: micron: correct bitmask for ecc status
+    - mtd: physmap-core: Restore map_rom fallback
+    - mmc: mtk-sd: Use readl_poll_timeout_atomic in msdc_reset_hw
+    - mmc: core: sdio: hold retuning if sdio in 1-bit mode
+    - pNFS: Fix a hang in nfs4_evict_inode()
+    - NFSv4.1: fixup use EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - ACPI: irq: Fix incorrect return value in acpi_register_gsi()
+    - nvme-pci: add BOGUS_NID for Intel 0a54 device
+    - nvme-rdma: do not try to stop unallocated queues
+    - USB: serial: option: add Telit LE910C4-WWX 0x1035 composition
+    - USB: serial: option: add entry for Sierra EM9191 with new firmware
+    - USB: serial: option: add Fibocom to DELL custom modem FM101R-GL
+    - s390/pci: fix iommu bitmap allocation
+    - selftests/ftrace: Add new test case which checks non unique symbol
+    - s390/cio: fix a memleak in css_alloc_subchannel
+    - platform/surface: platform_profile: Propagate error if profile registration
+      fails
+    - platform/x86: asus-wmi: Change ASUS_WMI_BRN_DOWN code from 0x20 to 0x2e
+    - platform/x86: asus-wmi: Map 0x2a code, Ignore 0x2b and 0x2c events
+    - gpio: vf610: set value before the direction to avoid a glitch
+    - ASoC: pxa: fix a memory leak in probe()
+    - serial: 8250: omap: Move uart_write() inside PM section
+    - phy: mapphone-mdm6600: Fix runtime disable on probe
+    - phy: mapphone-mdm6600: Fix runtime PM for remove
+    - phy: mapphone-mdm6600: Fix pinctrl_pm handling for sleep pins
+    - Bluetooth: hci_sock: fix slab oob read in create_monitor_event
+    - Bluetooth: hci_sock: Correctly bounds check and pad HCI_MON_NEW_INDEX name
+    - xfrm6: fix inet6_dev refcount underflow problem
+    - Linux 5.15.137
+  * CVE-2023-51782
+    - net/rose: Fix Use-After-Free in rose_ioctl
+  * CVE-2023-51779
+    - Bluetooth: af_bluetooth: Fix Use-After-Free in bt_sock_recvmsg
+  * CVE-2023-22995
+    - usb: dwc3: dwc3-qcom: Add missing platform_device_put() in
+      dwc3_qcom_acpi_register_core
+  * CVE-2023-4134
+    - Input: cyttsp4_core - change del_timer_sync() to timer_shutdown_sync()
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 24 Apr 2024 12:58:05 +1000
+
+linux-xilinx-zynqmp (5.15.0-1027.31) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1027.31 -proposed tracker (LP: #2054500)
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/d2024.02.07)
+
+  * Fix backported kria device tree changes (LP: #2054366)
+    - SAUCE: zynqmp.dtsi fix incorrectly backported changes
+
+  [ Ubuntu: 5.15.0-94.104 ]
+
+  * jammy/linux: 5.15.0-94.104 -proposed tracker (LP: #2048777)
+  * [SRU] Duplicate Device_dax ids Created and hence Probing is Failing.
+    (LP: #2028158)
+    - device-dax: Fix duplicate 'hmem' device registration
+  * Add ODM driver f81604 usb-can (LP: #2045387)
+    - can: usb: f81604: add Fintek F81604 support
+    - [Config] updateconfigs for ODM drivers CONFIG_CAN_F81604
+  * Add ODM driver gpio-m058ssan (LP: #2045386)
+    - SAUCE: ODM: gpio: add M058SSAN gpio driver
+    - [Config] updateconfigs for ODM drivers CONFIG_GPIO_M058SSAN
+  * Add ODM driver rtc-pcf85263 (LP: #2045385)
+    - SAUCE: ODM: rtc: add PCF85263 RTC driver
+    - [Config] updateconfigs for ODM drivers CONFIG_RTC_DRV_PCF85263
+  * AppArmor patch for mq-posix interface is missing in jammy (LP: #2045384)
+    - SAUCE: (no-up) apparmor: reserve mediation classes
+    - SAUCE: (no-up) apparmor: Add fine grained mediation of posix mqueues
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update annotations scripts
+
+  [ Ubuntu: 5.15.0-93.103 ]
+
+  * jammy/linux: 5.15.0-93.103 -proposed tracker (LP: #2048330)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] remove helper scripts
+    - [Packaging] update annotations scripts
+    - debian/dkms-versions -- update from kernel-versions (main/2024.01.08)
+  * Hotplugging SCSI disk in QEMU VM fails (LP: #2047382)
+    - Revert "PCI: acpiphp: Reassign resources on bridge if necessary"
+  * CVE-2023-6622
+    - netfilter: nf_tables: bail out on mismatching dynset and set expressions
+  * CVE-2024-0193
+    - netfilter: nf_tables: skip set commit for deleted/destroyed sets
+  * CVE-2023-6040
+    - netfilter: nf_tables: Reject tables of unsupported family
+  * Patches needed for AmpereOne (arm64) (LP: #2044192)
+    - clocksource/arm_arch_timer: Add build-time guards for unhandled register
+      accesses
+    - clocksource/drivers/arm_arch_timer: Drop CNT*_TVAL read accessors
+    - clocksource/drivers/arm_arch_timer: Extend write side of timer register
+      accessors to u64
+    - clocksource/drivers/arm_arch_timer: Move system register timer programming
+      over to CVAL
+    - clocksource/drivers/arm_arch_timer: Move drop _tval from erratum function
+      names
+    - clocksource/drivers/arm_arch_timer: Fix MMIO base address vs callback
+      ordering issue
+    - clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL
+    - clocksource/drivers/arm_arch_timer: Advertise 56bit timer to the core code
+    - clocksource/drivers/arm_arch_timer: Work around broken CVAL implementations
+    - clocksource/drivers/arm_arch_timer: Remove any trace of the TVAL programming
+      interface
+    - clocksource/drivers/arm_arch_timer: Drop unnecessary ISB on CVAL programming
+    - clocksource/drivers/arm_arch_timer: Fix masking for high freq counters
+    - clocksource/drivers/arch_arm_timer: Move workaround synchronisation around
+  * Add quirk to disable i915 fastboot on B&R PC (LP: #2047630)
+    - SAUCE: i915: force disable fastboot quirk
+  * Some machines can't pass the pm-graph test (LP: #2046217)
+    - wifi: iwlwifi: pcie: rescan bus if no parent
+  * Sound: Add rtl quirk of M90-Gen5 (LP: #2046105)
+    - ALSA: hda/realtek: Enable headset on Lenovo M90 Gen5
+  * linux tools packages for derived kernels refuse to install simultaneously
+    due to libcpupower name collision (LP: #2035971)
+    - [Packaging] Statically link libcpupower into cpupower tool
+  * [Debian] autoreconstruct - Do not generate chmod -x for deleted  files
+    (LP: #2045562)
+    - [Debian] autoreconstruct - Do not generate chmod -x for deleted files
+  * CVE-2023-6931
+    - perf/core: Add a new read format to get a number of lost samples
+    - perf: Fix perf_event_validate_size()
+    - perf: Fix perf_event_validate_size() lockdep splat
+  * CVE-2023-6932
+    - ipv4: igmp: fix refcnt uaf issue when receiving igmp query packet
+  * CVE-2023-6606
+    - smb: client: fix OOB in smbCalcSize()
+  * CVE-2023-6817
+    - netfilter: nft_set_pipapo: skip inactive elements during set walk
+  * Jammy update: v5.15.136 upstream stable release (LP: #2046008)
+    - iommu/vt-d: Avoid memory allocation in iommu_suspend()
+    - scsi: core: Use a structure member to track the SCSI command submitter
+    - scsi: core: Rename scsi_mq_done() into scsi_done() and export it
+    - scsi: ib_srp: Call scsi_done() directly
+    - RDMA/srp: Do not call scsi_done() from srp_abort()
+    - RDMA/cxgb4: Check skb value for failure to allocate
+    - perf/arm-cmn: Fix the unhandled overflow status of counter 4 to 7
+    - of: overlay: Reorder struct fragment fields kerneldoc
+    - platform/x86: think-lmi: Fix reference leak
+    - platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section
+      mismatch warning
+    - lib/test_meminit: fix off-by-one error in test_pages()
+    - HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect
+    - quota: Fix slow quotaoff
+    - net: prevent address rewrite in kernel_bind()
+    - ALSA: usb-audio: Fix microphone sound on Opencomm2 Headset
+    - KEYS: trusted: allow use of kernel RNG for key material
+    - KEYS: trusted: Remove redundant static calls usage
+    - drm/msm/dp: do not reinitialize phy unless retry during link training
+    - drm/msm/dsi: skip the wait for video mode done if not applicable
+    - drm/msm/dsi: fix irq_of_parse_and_map() error checking
+    - drm/msm/dpu: change _dpu_plane_calc_bw() to use u64 to avoid overflow
+    - ravb: Fix up dma_free_coherent() call in ravb_remove()
+    - ravb: Fix use-after-free issue in ravb_tx_timeout_work()
+    - ieee802154: ca8210: Fix a potential UAF in ca8210_probe
+    - mlxsw: fix mlxsw_sp2_nve_vxlan_learning_set() return type
+    - eth: remove copies of the NAPI_POLL_WEIGHT define
+    - xen-netback: use default TX queue size for vifs
+    - riscv, bpf: Factor out emit_call for kernel and bpf context
+    - riscv, bpf: Sign-extend return values
+    - drm/vmwgfx: fix typo of sizeof argument
+    - bpf: Fix verifier log for async callback return values
+    - net: macsec: indicate next pn update when offloading
+    - net: phy: mscc: macsec: reject PN update requests
+    - ixgbe: fix crash with empty VF macvlan list
+    - net/mlx5e: Again mutually exclude RX-FCS and RX-port-timestamp
+    - net: nfc: fix races in nfc_llcp_sock_get() and nfc_llcp_sock_get_sn()
+    - pinctrl: renesas: rzn1: Enable missing PINMUX
+    - nfc: nci: assert requested protocol is valid
+    - workqueue: Override implicit ordered attribute in
+      workqueue_apply_unbound_cpumask()
+    - net: add sysctl accept_ra_min_rtr_lft
+    - net: change accept_ra_min_rtr_lft to affect all RA lifetimes
+    - net: release reference to inet6_dev pointer
+    - media: mtk-jpeg: Fix use after free bug due to uncanceled work
+    - dmaengine: stm32-mdma: abort resume if no ongoing transfer
+    - xhci: Keep interrupt disabled in initialization until host is running.
+    - usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
+    - net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read
+    - usb: dwc3: Soft reset phy on probe for host
+    - usb: cdns3: Modify the return value of cdns_set_active () to void when
+      CONFIG_PM_SLEEP is disabled
+    - usb: musb: Get the musb_qh poniter after musb_giveback
+    - usb: musb: Modify the "HWVers" register address
+    - iio: pressure: bmp280: Fix NULL pointer exception
+    - iio: pressure: dps310: Adjust Timeout Settings
+    - iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
+    - drm/amdgpu: add missing NULL check
+    - drm/amd/display: Don't set dpms_off for seamless boot
+    - ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA
+    - x86/cpu: Fix AMD erratum #1485 on Zen4-based CPUs
+    - mcb: remove is_added flag from mcb_device struct
+    - thunderbolt: Workaround an IOMMU fault on certain systems with Intel Maple
+      Ridge
+    - thunderbolt: Check that lane 1 is in CL0 before enabling lane bonding
+    - libceph: use kernel_connect()
+    - ceph: fix incorrect revoked caps assert in ceph_fill_file_size()
+    - ceph: fix type promotion bug on 32bit systems
+    - Input: powermate - fix use-after-free in powermate_config_complete
+    - Input: psmouse - fix fast_reconnect function for PS/2 mode
+    - Input: xpad - add PXN V900 support
+    - Input: i8042 - add Fujitsu Lifebook E5411 to i8042 quirk table
+    - Input: goodix - ensure int GPIO is in input for gpio_count == 1 &&
+      gpio_int_idx == 0 case
+    - tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
+    - cgroup: Remove duplicates in cgroup v1 tasks file
+    - counter: microchip-tcb-capture: Fix the use of internal GCLK logic
+    - usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
+    - usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
+    - usb: cdnsp: Fixes issue with dequeuing not queued requests
+    - x86/alternatives: Disable KASAN in apply_alternatives()
+    - dmaengine: idxd: use spin_lock_irqsave before wait_event_lock_irq
+    - dmaengine: mediatek: Fix deadlock caused by synchronize_irq()
+    - powerpc/8xx: Fix pte_access_permitted() for PAGE_NONE
+    - powerpc/64e: Fix wrong test in __ptep_test_and_clear_young()
+    - arm64: report EL1 UNDEFs better
+    - arm64: die(): pass 'err' as long
+    - arm64: consistently pass ESR_ELx to die()
+    - arm64: rework FPAC exception handling
+    - arm64: rework BTI exception handling
+    - arm64: allow kprobes on EL0 handlers
+    - arm64: split EL0/EL1 UNDEF handlers
+    - arm64: factor out EL1 SSBS emulation hook
+    - arm64: factor insn read out of call_undef_hook()
+    - arm64: rework EL0 MRS emulation
+    - arm64: armv8_deprecated: fold ops into insn_emulation
+    - arm64: armv8_deprecated move emulation functions
+    - arm64: armv8_deprecated: move aarch32 helper earlier
+    - arm64: armv8_deprecated: rework deprected instruction handling
+    - arm64: armv8_deprecated: fix unused-function error
+    - usb: hub: Guard against accesses to uninitialized BOS descriptors
+    - eth: remove remaining copies of the NAPI_POLL_WEIGHT define
+    - Linux 5.15.136
+  * Jammy update: v5.15.135 upstream stable release (LP: #2045809)
+    - spi: zynqmp-gqspi: Convert to platform remove callback returning void
+    - spi: zynqmp-gqspi: fix clock imbalance on probe failure
+    - ASoC: soc-utils: Export snd_soc_dai_is_dummy() symbol
+    - ASoC: tegra: Fix redundant PLLA and PLLA_OUT0 updates
+    - NFS: Cleanup unused rpc_clnt variable
+    - NFS: rename nfs_client_kset to nfs_kset
+    - NFSv4: Fix a state manager thread deadlock regression
+    - ring-buffer: remove obsolete comment for free_buffer_page()
+    - ring-buffer: Fix bytes info in per_cpu buffer stats
+    - arm64: Avoid repeated AA64MMFR1_EL1 register read on pagefault path
+    - iommu/arm-smmu-v3: Set TTL invalidation hint better
+    - iommu/arm-smmu-v3: Avoid constructing invalid range commands
+    - rbd: move rbd_dev_refresh() definition
+    - rbd: decouple header read-in from updating rbd_dev->header
+    - rbd: decouple parent info read-in from updating rbd_dev
+    - rbd: take header_rwsem in rbd_dev_refresh() only when updating
+    - block: fix use-after-free of q->q_usage_counter
+    - scsi: zfcp: Fix a double put in zfcp_port_enqueue()
+    - qed/red_ll2: Fix undefined behavior bug in struct qed_ll2_info
+    - wifi: mwifiex: Fix tlv_buf_left calculation
+    - net: replace calls to sock->ops->connect() with kernel_connect()
+    - net: prevent rewrite of msg_name in sock_sendmsg()
+    - drm/amd: Fix detection of _PR3 on the PCIe root port
+    - arm64: Add Cortex-A520 CPU part definition
+    - HID: sony: Fix a potential memory leak in sony_probe()
+    - ubi: Refuse attaching if mtd's erasesize is 0
+    - wifi: iwlwifi: dbg_ini: fix structure packing
+    - iwlwifi: avoid void pointer arithmetic
+    - wifi: iwlwifi: mvm: Fix a memory corruption issue
+    - wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
+    - bpf: Fix tr dereferencing
+    - drivers/net: process the result of hdlc_open() and add call of hdlc_close()
+      in uhdlc_close()
+    - wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
+    - regmap: rbtree: Fix wrong register marked as in-cache when creating new node
+    - ima: Finish deprecation of IMA_TRUSTED_KEYRING Kconfig
+    - [Config] updateconfigs for IMA_BLACKLIST_KEYRING
+    - scsi: target: core: Fix deadlock due to recursive locking
+    - ima: rework CONFIG_IMA dependency block
+    - NFSv4: Fix a nfs4_state_manager() race
+    - bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
+    - modpost: add missing else to the "of" check
+    - net: fix possible store tearing in neigh_periodic_work()
+    - ipv4, ipv6: Fix handling of transhdrlen in __ip{,6}_append_data()
+    - ptp: ocp: Fix error handling in ptp_ocp_device_init
+    - net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent
+    - net: usb: smsc75xx: Fix uninit-value access in __smsc75xx_read_reg
+    - net: nfc: llcp: Add lock when modifying device list
+    - net: ethernet: ti: am65-cpsw: Fix error code in
+      am65_cpsw_nuss_init_tx_chns()
+    - ibmveth: Remove condition to recompute TCP header checksum.
+    - netfilter: handle the connecting collision properly in
+      nf_conntrack_proto_sctp
+    - netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
+    - ipv4: Set offload_failed flag in fibmatch results
+    - net: stmmac: dwmac-stm32: fix resume on STM32 MCU
+    - tipc: fix a potential deadlock on &tx->lock
+    - tcp: fix quick-ack counting to count actual ACKs of new data
+    - tcp: fix delayed ACKs for MSS boundary condition
+    - sctp: update transport state when processing a dupcook packet
+    - sctp: update hb timer immediately after users change hb_interval
+    - HID: sony: remove duplicate NULL check before calling usb_free_urb()
+    - HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit
+    - dm zoned: free dmz->ddev array in dmz_put_zoned_devices
+    - RDMA/core: Require admin capabilities to set system parameters
+    - of: dynamic: Fix potential memory leak in of_changeset_action()
+    - IB/mlx4: Fix the size of a buffer in add_port_entries()
+    - gpio: aspeed: fix the GPIO number passed to pinctrl_gpio_set_config()
+    - gpio: pxa: disable pinctrl calls for MMP_GPIO
+    - RDMA/cma: Initialize ib_sa_multicast structure to 0 when join
+    - RDMA/cma: Fix truncation compilation warning in make_cma_ports
+    - RDMA/uverbs: Fix typo of sizeof argument
+    - RDMA/siw: Fix connection failure handling
+    - RDMA/mlx5: Fix NULL string error
+    - ksmbd: fix uaf in smb20_oplock_break_ack
+    - parisc: Restore __ldcw_align for PA-RISC 2.0 processors
+    - xen/events: replace evtchn_rwlock with RCU
+    - Linux 5.15.135
+  * CVE-2023-46813
+    - x86/sev: Disable MMIO emulation from user mode
+    - x86/sev: Check IOBM for IOIO exceptions from user-space
+    - x86/sev: Check for user-space IOIO pointing to kernel space
+  * CVE-2023-6111
+    - netfilter: nf_tables: remove catchall element in GC sync path
+  * Change in trace file leads to test timeout in ftrace tests on 5.15 ARM64
+    (LP: #2029405)
+    - selftests/ftrace: Stop tracing while reading the trace file by default
+  * Fix ADL: System enabled AHCI can't get into s0ix when attached ODD
+    (LP: #2037493)
+    - ata: ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list
+  * Kernel doesn't compile with CONFIG_IMA (LP: #2041842)
+    - SAUCE: LSM: Fix typo in ima_filter_rule_match struct argument
+  * CVE-2023-32252
+    - ksmbd: add smb-direct shutdown
+    - ksmbd: Implements sess->ksmbd_chann_list as xarray
+    - ksmbd: fix racy issue from session setup and logoff
+  * Jammy update: v5.15.134 upstream stable release (LP: #2044023)
+    - NFS: Use the correct commit info in nfs_join_page_group()
+    - NFS: More fixes for nfs_direct_write_reschedule_io()
+    - NFS/pNFS: Report EINVAL errors from connect() to the server
+    - SUNRPC: Mark the cred for revalidation if the server rejects it
+    - NFSv4.1: use EXCHGID4_FLAG_USE_PNFS_DS for DS server
+    - NFSv4.1: fix pnfs MDS=DS session trunking
+    - tracing: Make trace_marker{,_raw} stream-like
+    - tracing: Increase trace array ref count on enable and filter files
+    - ata: ahci: Drop pointless VPRINTK() calls and convert the remaining ones
+    - ata: libahci: clear pending interrupt status
+    - ext4: scope ret locally in ext4_try_to_trim_range()
+    - ext4: change s_last_trim_minblks type to unsigned long
+    - ext4: replace the traditional ternary conditional operator with with
+      max()/min()
+    - ext4: move setting of trimmed bit into ext4_try_to_trim_range()
+    - ext4: do not let fstrim block system suspend
+    - tracing: Have event inject files inc the trace array ref count
+    - netfilter: nft_set_rbtree: use read spinlock to avoid datapath contention
+    - netfilter: nft_set_pipapo: call nft_trans_gc_queue_sync() in catchall GC
+    - netfilter: nft_set_pipapo: stop GC iteration if GC transaction allocation
+      fails
+    - netfilter: nft_set_hash: try later when GC hits EAGAIN on iteration
+    - netfilter: nf_tables: fix memleak when more than 255 elements expired
+    - ASoC: meson: spdifin: start hw on dai probe
+    - netfilter: nf_tables: disallow element removal on anonymous sets
+    - bpf: Avoid deadlock when using queue and stack maps from NMI
+    - selftests: tls: swap the TX and RX sockets in some tests
+    - net/core: Fix ETH_P_1588 flow dissector
+    - ASoC: imx-audmix: Fix return error with devm_clk_get()
+    - iavf: do not process adminq tasks when __IAVF_IN_REMOVE_TASK is set
+    - i40e: Add VF VLAN pruning
+    - i40e: Fix VF VLAN offloading when port VLAN is configured
+    - ionic: fix 16bit math issue when PAGE_SIZE >= 64KB
+    - igc: Fix infinite initialization loop with early XDP redirect
+    - powerpc/perf/hv-24x7: Update domain value check
+    - dccp: fix dccp_v4_err()/dccp_v6_err() again
+    - platform/x86: intel_scu_ipc: Check status after timeout in busy_loop()
+    - platform/x86: intel_scu_ipc: Check status upon timeout in
+      ipc_wait_for_interrupt()
+    - platform/x86: intel_scu_ipc: Don't override scu in
+      intel_scu_ipc_dev_simple_command()
+    - platform/x86: intel_scu_ipc: Fail IPC send if still busy
+    - x86/srso: Fix srso_show_state() side effect
+    - x86/srso: Fix SBPB enablement for spec_rstack_overflow=off
+    - net: hns3: fix GRE checksum offload issue
+    - net: hns3: only enable unicast promisc when mac table full
+    - net: hns3: fix fail to delete tc flower rules during reset issue
+    - net: hns3: add 5ms delay before clear firmware reset irq source
+    - net: bridge: use DEV_STATS_INC()
+    - team: fix null-ptr-deref when team device type is changed
+    - net: rds: Fix possible NULL-pointer dereference
+    - netfilter: nf_tables: disable toggling dormant table state more than once
+    - locking/seqlock: Do the lockdep annotation before locking in
+      do_write_seqcount_begin_nested()
+    - net: ena: Flush XDP packets on error.
+    - bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
+    - igc: Expose tx-usecs coalesce setting to user
+    - Fix up backport of 136191703038 ("interconnect: Teach lockdep about
+      icc_bw_lock order")
+    - gpio: tb10x: Fix an error handling path in tb10x_gpio_probe()
+    - i2c: mux: demux-pinctrl: check the return value of devm_kstrdup()
+    - i2c: mux: gpio: Replace custom acpi_get_local_address()
+    - i2c: mux: gpio: Add missing fwnode_handle_put()
+    - xfs: bound maximum wait time for inodegc work
+    - xfs: introduce xfs_inodegc_push()
+    - xfs: explicitly specify cpu when forcing inodegc delayed work to run
+      immediately
+    - xfs: check that per-cpu inodegc workers actually run on that cpu
+    - xfs: disable reaping in fscounters scrub
+    - xfs: fix xfs_inodegc_stop racing with mod_delayed_work
+    - Input: i8042 - rename i8042-x86ia64io.h to i8042-acpipnpio.h
+    - Input: i8042 - add quirk for TUXEDO Gemini 17 Gen1/Clevo PD70PN
+    - netfilter: exthdr: add support for tcp option removal
+    - netfilter: nft_exthdr: Fix non-linear header modification
+    - ata: libata: Rename link flag ATA_LFLAG_NO_DB_DELAY
+    - ata: ahci: Add support for AMD A85 FCH (Hudson D4)
+    - ata: ahci: Rename board_ahci_mobile
+    - ata: ahci: Add Elkhart Lake AHCI controller
+    - scsi: qla2xxx: Select qpair depending on which CPU post_cmd() gets called
+    - scsi: qla2xxx: Use raw_smp_processor_id() instead of smp_processor_id()
+    - btrfs: reset destination buffer when read_extent_buffer() gets invalid range
+    - MIPS: Alchemy: only build mmc support helpers if au1xmmc is enabled
+    - drm/bridge: ti-sn65dsi83: Do not generate HFP/HBP/HSA and EOT packet
+    - bus: ti-sysc: Use fsleep() instead of usleep_range() in sysc_reset()
+    - bus: ti-sysc: Fix missing AM35xx SoC matching
+    - clk: tegra: fix error return case for recalc_rate
+    - treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_56.RULE
+      (part 1)
+    - ARM: dts: omap: correct indentation
+    - ARM: dts: ti: omap: Fix bandgap thermal cells addressing for omap3/4
+    - ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot
+    - bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up
+    - power: supply: ucs1002: fix error code in ucs1002_get_property()
+    - firmware: imx-dsp: Fix an error handling path in imx_dsp_setup_channels()
+    - xtensa: add default definition for XCHAL_HAVE_DIV32
+    - xtensa: iss/network: make functions static
+    - xtensa: boot: don't add include-dirs
+    - xtensa: boot/lib: fix function prototypes
+    - soc: imx8m: Enable OCOTP clock for imx8mm before reading registers
+    - gpio: pmic-eic-sprd: Add can_sleep flag for PMIC EIC chip
+    - i2c: npcm7xx: Fix callback completion ordering
+    - dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock
+    - spi: sun6i: reduce DMA RX transfer width to single byte
+    - spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
+    - parisc: sba: Fix compile warning wrt list of SBA devices
+    - parisc: iosapic.c: Fix sparse warnings
+    - parisc: drivers: Fix sparse warning
+    - parisc: irq: Make irq_stack_union static to avoid sparse warning
+    - scsi: qedf: Add synchronization between I/O completions and abort
+    - scsi: ufs: core: Move __ufshcd_send_uic_cmd() outside host_lock
+    - selftests/ftrace: Correctly enable event in instance-event.tc
+    - ring-buffer: Avoid softlockup in ring_buffer_resize()
+    - btrfs: improve error message after failure to add delayed dir index item
+    - selftests: fix dependency checker script
+    - ring-buffer: Do not attempt to read past "commit"
+    - platform/mellanox: mlxbf-bootctl: add NET dependency into Kconfig
+    - drm/amd/display: Don't check registers, if using AUX BL control
+    - drm/amdgpu: Handle null atom context in VBIOS info ioctl
+    - scsi: pm80xx: Use phy-specific SAS address when sending PHY_START command
+    - scsi: pm80xx: Avoid leaking tags when processing
+      OPC_INB_SET_CONTROLLER_CONFIG command
+    - smb3: correct places where ENOTSUPP is used instead of preferred EOPNOTSUPP
+    - ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()
+    - spi: nxp-fspi: reset the FLSHxCR1 registers
+    - spi: stm32: add a delay before SPI disable
+    - ASoC: fsl: imx-pcm-rpmsg: Add SNDRV_PCM_INFO_BATCH flag
+    - bpf: Clarify error expectations from bpf_clone_redirect
+    - ASoC: imx-rpmsg: Set ignore_pmdown_time for dai_link
+    - media: vb2: frame_vector.c: replace WARN_ONCE with a comment
+    - powerpc/watchpoints: Disable preemption in thread_change_pc()
+    - powerpc/watchpoint: Disable pagefaults when getting user instruction
+    - powerpc/watchpoints: Annotate atomic context in more places
+    - ncsi: Propagate carrier gain/loss events to the NCSI controller
+    - fbdev/sh7760fb: Depend on FB=y
+    - perf build: Define YYNOMEM as YYNOABORT for bison < 3.81
+    - sched/cpuacct: Optimize away RCU read lock
+    - cgroup: Fix suspicious rcu_dereference_check() usage warning
+    - nvme-pci: factor the iod mempool creation into a helper
+    - nvme-pci: factor out a nvme_pci_alloc_dev helper
+    - nvme-pci: do not set the NUMA node of device if it has none
+    - watchdog: iTCO_wdt: No need to stop the timer in probe
+    - watchdog: iTCO_wdt: Set NO_REBOOT if the watchdog is not already running
+    - i40e: fix potential NULL pointer dereferencing of pf->vf
+      i40e_sync_vsi_filters()
+    - scsi: qla2xxx: Fix NULL pointer dereference in target mode
+    - nvme-pci: always return an ERR_PTR from nvme_pci_alloc_dev
+    - smack: Record transmuting in smk_transmuted
+    - smack: Retrieve transmuting information in smack_inode_getsecurity()
+    - Smack:- Use overlay inode label in smack_inode_copy_up()
+    - iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range
+    - x86/srso: Add SRSO mitigation for Hygon processors
+    - Revert "tty: n_gsm: fix UAF in gsm_cleanup_mux"
+    - serial: 8250_port: Check IRQ data before use
+    - nilfs2: fix potential use after free in nilfs_gccache_submit_read_data()
+    - ALSA: hda: Disable power save for solving pop issue on Lenovo ThinkCentre
+      M70q
+    - ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
+    - i2c: i801: unregister tco_pdev in i801_probe() error path
+    - sched/rt: Fix live lock between select_fallback_rq() and RT push
+    - io_uring/fs: remove sqe->rw_flags checking from LINKAT
+    - Revert "SUNRPC dont update timeout value on connection reset"
+    - proc: nommu: /proc/<pid>/maps: release mmap read lock
+    - ring-buffer: Update "shortest_full" in polling
+    - btrfs: properly report 0 avail for very full file systems
+    - bpf: Fix BTF_ID symbol generation collision
+    - bpf: Fix BTF_ID symbol generation collision in tools/
+    - net: thunderbolt: Fix TCPv6 GSO checksum calculation
+    - ata: libata-core: Fix ata_port_request_pm() locking
+    - ata: libata-core: Fix port and device removal
+    - ata: libata-core: Do not register PM operations for SAS ports
+    - ata: libata-sata: increase PMP SRST timeout to 10s
+    - fs: binfmt_elf_efpic: fix personality for ELF-FDPIC
+    - drm/meson: fix memory leak on ->hpd_notify callback
+    - Linux 5.15.134
+  * Jammy update: v5.15.133 upstream stable release (LP: #2043422)
+    - autofs: fix memory leak of waitqueues in autofs_catatonic_mode
+    - btrfs: output extra debug info if we failed to find an inline backref
+    - locks: fix KASAN: use-after-free in trace_event_raw_event_filelock_lock
+    - ACPICA: Add AML_NO_OPERAND_RESOLVE flag to Timer
+    - kernel/fork: beware of __put_task_struct() calling context
+    - rcuscale: Move rcu_scale_writer() schedule_timeout_uninterruptible() to
+      _idle()
+    - scftorture: Forgive memory-allocation failure if KASAN
+    - ACPI: video: Add backlight=native DMI quirk for Lenovo Ideapad Z470
+    - perf/smmuv3: Enable HiSilicon Erratum 162001900 quirk for HIP08/09
+    - perf/imx_ddr: speed up overflow frequency of cycle
+    - hw_breakpoint: fix single-stepping when using bpf_overflow_handler
+    - ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
+    - devlink: remove reload failed checks in params get/set callbacks
+    - crypto: lrw,xts - Replace strlcpy with strscpy
+    - wifi: ath9k: fix fortify warnings
+    - wifi: ath9k: fix printk specifier
+    - wifi: mwifiex: fix fortify warning
+    - wifi: wil6210: fix fortify warnings
+    - crypto: lib/mpi - avoid null pointer deref in mpi_cmp_ui()
+    - tpm_tis: Resend command to recover from data transfer errors
+    - mmc: sdhci-esdhc-imx: improve ESDHC_FLAG_ERR010450
+    - alx: fix OOB-read compiler warning
+    - wifi: mac80211: check S1G action frame size
+    - netfilter: ebtables: fix fortify warnings in size_entry_mwt()
+    - wifi: mac80211_hwsim: drop short frames
+    - drm/bridge: tc358762: Instruct DSI host to generate HSE packets
+    - arm64: dts: qcom: sm6125-pdx201: correct ramoops pmsg-size
+    - arm64: dts: qcom: sm8150-kumano: correct ramoops pmsg-size
+    - arm64: dts: qcom: sm8250-edo: correct ramoops pmsg-size
+    - samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'
+    - ALSA: hda: intel-dsp-cfg: add LunarLake support
+    - drm/amd/display: Blocking invalid 420 modes on HDMI TMDS for DCN31
+    - drm/exynos: fix a possible null-pointer dereference due to data race in
+      exynos_drm_crtc_atomic_disable()
+    - bus: ti-sysc: Configure uart quirks for k3 SoC
+    - md: raid1: fix potential OOB in raid1_remove_disk()
+    - ext2: fix datatype of block number in ext2_xattr_set2()
+    - fs/jfs: prevent double-free in dbUnmount() after failed jfs_remount()
+    - jfs: fix invalid free of JFS_IP(ipimap)->i_imap in diUnmount
+    - ARM: 9317/1: kexec: Make smp stop calls asynchronous
+    - powerpc/pseries: fix possible memory leak in ibmebus_bus_init()
+    - PCI: fu740: Set the number of MSI vectors
+    - media: dvb-usb-v2: af9035: Fix null-ptr-deref in af9035_i2c_master_xfer
+    - media: dw2102: Fix null-ptr-deref in dw2102_i2c_transfer()
+    - media: af9005: Fix null-ptr-deref in af9005_i2c_xfer
+    - media: anysee: fix null-ptr-deref in anysee_master_xfer
+    - media: az6007: Fix null-ptr-deref in az6007_i2c_xfer()
+    - media: dvb-usb-v2: gl861: Fix null-ptr-deref in gl861_i2c_master_xfer
+    - media: tuners: qt1010: replace BUG_ON with a regular error
+    - media: pci: cx23885: replace BUG with error return
+    - usb: cdns3: Put the cdns set active part outside the spin lock
+    - usb: gadget: fsl_qe_udc: validate endpoint index for ch9 udc
+    - tools: iio: iio_generic_buffer: Fix some integer type and calculation
+    - scsi: target: iscsi: Fix buffer overflow in lio_target_nacl_info_show()
+    - serial: cpm_uart: Avoid suspicious locking
+    - usb: ehci: add workaround for chipidea PORTSC.PEC bug
+    - media: pci: ipu3-cio2: Initialise timing struct to avoid a compiler warning
+    - kobject: Add sanity check for kset->kobj.ktype in kset_register()
+    - interconnect: Fix locking for runpm vs reclaim
+    - printk: Consolidate console deferred printing
+    - jbd2: refactor wait logic for transaction updates into a common function
+    - jbd2: fix use-after-free of transaction_t race
+    - jbd2: kill t_handle_lock transaction spinlock
+    - jbd2: rename jbd_debug() to jbd2_debug()
+    - jbd2: correct the end of the journal recovery scan range
+    - mtd: rawnand: brcmnand: Allow SoC to provide I/O operations
+    - mtd: rawnand: brcmnand: Fix ECC level field setting for v7.2 controller
+    - MIPS: Use "grep -E" instead of "egrep"
+    - perf test: Remove bash construct from stat_bpf_counters.sh test
+    - perf test shell stat_bpf_counters: Fix test on Intel
+    - btrfs: move btrfs_pinned_by_swapfile prototype into volumes.h
+    - btrfs: add a helper to read the superblock metadata_uuid
+    - btrfs: compare the correct fsid/metadata_uuid in btrfs_validate_super
+    - drm: gm12u320: Fix the timeout usage for usb_bulk_msg()
+    - scsi: qla2xxx: Fix NULL vs IS_ERR() bug for debugfs_create_dir()
+    - selftests: tracing: Fix to unmount tracefs for recovering environment
+    - scsi: lpfc: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
+    - x86/boot/compressed: Reserve more memory for page tables
+    - x86/purgatory: Remove LTO flags
+    - samples/hw_breakpoint: fix building without module unloading
+    - md/raid1: fix error: ISO C90 forbids mixed declarations
+    - attr: block mode changes of symlinks
+    - ovl: fix failed copyup of fileattr on a symlink
+    - ovl: fix incorrect fdput() on aio completion
+    - btrfs: fix lockdep splat and potential deadlock after failure running
+      delayed items
+    - btrfs: release path before inode lookup during the ino lookup ioctl
+    - tracing: Have tracing_max_latency inc the trace array ref count
+    - tracing: Have current_trace inc the trace array ref count
+    - tracing: Have option files inc the trace array ref count
+    - nfsd: fix change_info in NFSv4 RENAME replies
+    - tracefs: Add missing lockdown check to tracefs_create_dir()
+    - i2c: aspeed: Reset the i2c controller when timeout occurs
+    - ata: libata: disallow dev-initiated LPM transitions to unsupported states
+    - scsi: megaraid_sas: Fix deadlock on firmware crashdump
+    - scsi: pm8001: Setup IRQs on resume
+    - ext4: fix rec_len verify error
+    - drm/amd/display: fix the white screen issue when >= 64GB DRAM
+    - drm/amdgpu: fix amdgpu_cs_p1_user_fence
+    - drm/amd/display: enable cursor degamma for DCN3+ DRM legacy gamma
+    - interconnect: Teach lockdep about icc_bw_lock order
+    - Linux 5.15.133
+  * Jammy update: v5.15.132 upstream stable release (LP: #2041702)
+    - ARM: dts: imx: update sdma node name format
+    - ARM: dts: imx7s: Drop dma-apb interrupt-names
+    - ARM: dts: imx: Adjust dma-apbh node name
+    - ARM: dts: imx: Set default tuning step for imx7d usdhc
+    - phy: qcom-snps-femto-v2: use qcom_snps_hsphy_suspend/resume error code
+    - media: pulse8-cec: handle possible ping error
+    - media: pci: cx23885: fix error handling for cx23885 ATSC boards
+    - 9p: virtio: make sure 'offs' is initialized in zc_request
+    - ksmbd: fix out of bounds in smb3_decrypt_req()
+    - ksmbd: no response from compound read
+    - ASoC: da7219: Flush pending AAD IRQ when suspending
+    - ASoC: da7219: Check for failure reading AAD IRQ events
+    - ethernet: atheros: fix return value check in atl1c_tso_csum()
+    - vxlan: generalize vxlan_parse_gpe_hdr and remove unused args
+    - m68k: Fix invalid .section syntax
+    - s390/dasd: use correct number of retries for ERP requests
+    - s390/dasd: fix hanging device after request requeue
+    - fs/nls: make load_nls() take a const parameter
+    - ASoC: rt5682-sdw: fix for JD event handling in ClockStop Mode0
+    - ASoc: codecs: ES8316: Fix DMIC config
+    - ASoC: rt711: fix for JD event handling in ClockStop Mode0
+    - ASoC: rt711-sdca: fix for JD event handling in ClockStop Mode0
+    - ASoC: atmel: Fix the 8K sample parameter in I2SC master
+    - platform/x86: intel: hid: Always call BTNL ACPI method
+    - platform/x86/intel/hid: Add HP Dragonfly G2 to VGBS DMI quirks
+    - platform/x86: huawei-wmi: Silence ambient light sensor
+    - drm/amd/display: Exit idle optimizations before attempt to access PHY
+    - ovl: Always reevaluate the file signature for IMA
+    - ata: pata_arasan_cf: Use dev_err_probe() instead dev_err() in data_xfer()
+    - security: keys: perform capable check only on privileged operations
+    - kprobes: Prohibit probing on CFI preamble symbol
+    - clk: fixed-mmio: make COMMON_CLK_FIXED_MMIO depend on HAS_IOMEM
+    - vmbus_testing: fix wrong python syntax for integer value comparison
+    - net: usb: qmi_wwan: add Quectel EM05GV2
+    - wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
+    - idmaengine: make FSL_EDMA and INTEL_IDMA64 depends on HAS_IOMEM
+    - scsi: lpfc: Remove reftag check in DIF paths
+    - scsi: qedi: Fix potential deadlock on &qedi_percpu->p_work_lock
+    - net: hns3: restore user pause configure when disable autoneg
+    - drm/amdgpu: Match against exact bootloader status
+    - netlabel: fix shift wrapping bug in netlbl_catmap_setlong()
+    - bnx2x: fix page fault following EEH recovery
+    - sctp: handle invalid error codes without calling BUG()
+    - scsi: storvsc: Always set no_report_opcodes
+    - scsi: lpfc: Fix incorrect big endian type assignment in bsg loopback path
+    - ALSA: seq: oss: Fix racy open/close of MIDI devices
+    - tracing: Introduce pipe_cpumask to avoid race on trace_pipes
+    - platform/mellanox: Fix mlxbf-tmfifo not handling all virtio CONSOLE
+      notifications
+    - arm64: lib: Import latest version of Arm Optimized Routines' strncmp
+    - of: kexec: Mark ima_{free,stable}_kexec_buffer() as __init
+    - udf: Check consistency of Space Bitmap Descriptor
+    - udf: Handle error when adding extent to a file
+    - Revert "net: macsec: preserve ingress frame ordering"
+    - reiserfs: Check the return value from __getblk()
+    - eventfd: prevent underflow for eventfd semaphores
+    - fs: Fix error checking for d_hash_and_lookup()
+    - tmpfs: verify {g,u}id mount options correctly
+    - selftests/harness: Actually report SKIP for signal tests
+    - ARM: ptrace: Restore syscall restart tracing
+    - ARM: ptrace: Restore syscall skipping for tracers
+    - refscale: Fix uninitalized use of wait_queue_head_t
+    - OPP: Fix passing 0 to PTR_ERR in _opp_attach_genpd()
+    - selftests/resctrl: Make resctrl_tests run using kselftest framework
+    - selftests/resctrl: Add resctrl.h into build deps
+    - selftests/resctrl: Don't leak buffer in fill_cache()
+    - selftests/resctrl: Unmount resctrl FS if child fails to run benchmark
+    - selftests/resctrl: Close perf value read fd on errors
+    - x86/decompressor: Don't rely on upper 32 bits of GPRs being preserved
+    - perf/imx_ddr: don't enable counter0 if none of 4 counters are used
+    - selftests/futex: Order calls to futex_lock_pi
+    - s390/pkey: fix/harmonize internal keyblob headers
+    - s390/paes: fix PKEY_TYPE_EP11_AES handling for secure keyblobs
+    - ACPI: x86: s2idle: Post-increment variables when getting constraints
+    - ACPI: x86: s2idle: Fix a logic error parsing AMD constraints table
+    - x86/efistub: Fix PCI ROM preservation in mixed mode
+    - cpufreq: powernow-k8: Use related_cpus instead of cpus in driver.exit()
+    - bpftool: Use a local bpf_perf_event_value to fix accessing its fields
+    - bpf: Clear the probe_addr for uprobe
+    - tcp: tcp_enter_quickack_mode() should be static
+    - hwrng: nomadik - keep clock enabled while hwrng is registered
+    - hwrng: pic32 - use devm_clk_get_enabled
+    - regmap: rbtree: Use alloc_flags for memory allocations
+    - udp: re-score reuseport groups when connected sockets are present
+    - bpf: reject unhashed sockets in bpf_sk_assign
+    - ipv6: Add reasons for skb drops to __udp6_lib_rcv
+    - wifi: mt76: testmode: add nla_policy for MT76_TM_ATTR_TX_LENGTH
+    - spi: tegra20-sflash: fix to check return value of platform_get_irq() in
+      tegra_sflash_probe()
+    - can: gs_usb: gs_usb_receive_bulk_callback(): count RX overflow errors also
+      in case of OOM
+    - wifi: mt76: mt7915: fix power-limits while chan_switch
+    - wifi: mwifiex: Fix OOB and integer underflow when rx packets
+    - wifi: mwifiex: fix error recovery in PCIE buffer descriptor management
+    - crypto: stm32 - Properly handle pm_runtime_get failing
+    - crypto: api - Use work queue in crypto_destroy_instance
+    - Bluetooth: nokia: fix value check in nokia_bluetooth_serdev_probe()
+    - Bluetooth: Fix potential use-after-free when clear keys
+    - net: tcp: fix unexcepted socket die when snd_wnd is 0
+    - selftests/bpf: Clean up fmod_ret in bench_rename test script
+    - net-memcg: Fix scope of sockmem pressure indicators
+    - ice: ice_aq_check_events: fix off-by-one check when filling buffer
+    - crypto: caam - fix unchecked return value error
+    - hwrng: iproc-rng200 - Implement suspend and resume calls
+    - lwt: Fix return values of BPF xmit ops
+    - lwt: Check LWTUNNEL_XMIT_CONTINUE strictly
+    - fs: ocfs2: namei: check return value of ocfs2_add_entry()
+    - wifi: mwifiex: fix memory leak in mwifiex_histogram_read()
+    - wifi: mwifiex: Fix missed return in oob checks failed path
+    - samples/bpf: fix broken map lookup probe
+    - wifi: ath9k: fix races between ath9k_wmi_cmd and ath9k_wmi_ctrl_rx
+    - wifi: ath9k: protect WMI command response buffer replacement with a lock
+    - wifi: nl80211/cfg80211: add forgotten nla_policy for BSS color attribute
+    - wifi: mwifiex: avoid possible NULL skb pointer dereference
+    - Bluetooth: btusb: Do not call kfree_skb() under spin_lock_irqsave()
+    - wifi: ath9k: use IS_ERR() with debugfs_create_dir()
+    - net: arcnet: Do not call kfree_skb() under local_irq_disable()
+    - mlxsw: i2c: Fix chunk size setting in output mailbox buffer
+    - mlxsw: i2c: Limit single transaction buffer size
+    - hwmon: (tmp513) Fix the channel number in tmp51x_is_visible()
+    - netrom: Deny concurrent connect().
+    - drm/bridge: tc358764: Fix debug print parameter order
+    - quota: factor out dquot_write_dquot()
+    - quota: rename dquot_active() to inode_quota_active()
+    - quota: add new helper dquot_active()
+    - quota: fix dqput() to follow the guarantees dquot_srcu should provide
+    - ASoC: stac9766: fix build errors with REGMAP_AC97
+    - soc: qcom: ocmem: Add OCMEM hardware version print
+    - soc: qcom: ocmem: Fix NUM_PORTS & NUM_MACROS macros
+    - arm64: dts: qcom: sm8250: correct dynamic power coefficients
+    - arm64: dts: qcom: sm8250-edo: Add gpio line names for TLMM
+    - arm64: dts: qcom: sm8250-edo: Add GPIO line names for PMIC GPIOs
+    - arm64: dts: qcom: sm8250-edo: Rectify gpio-keys
+    - arm64: dts: qcom: msm8996: Add missing interrupt to the USB2 controller
+    - arm64: dts: qcom: sm8350: Add missing LMH interrupts to cpufreq
+    - arm64: dts: qcom: sm8350: Use proper CPU compatibles
+    - arm64: dts: qcom: pmk8350: fix ADC-TM compatible string
+    - arm64: dts: qcom: sm8250: Mark PCIe hosts as DMA coherent
+    - drm/amdgpu: avoid integer overflow warning in amdgpu_device_resize_fb_bar()
+    - ARM: dts: BCM53573: Add cells sizes to PCIe node
+    - ARM: dts: BCM53573: Use updated "spi-gpio" binding properties
+    - arm64: dts: qcom: sm8250-sony-xperia: correct GPIO keys wakeup again
+    - arm64: dts: qcom: pmi8998: Add node for WLED
+    - arm64: dts: qcom: correct SPMI WLED register range encoding
+    - arm64: dts: qcom: pm660l: Add missing short interrupt
+    - arm64: dts: qcom: pmi8994: Remove hardcoded linear WLED enabled-strings
+    - arm64: dts: qcom: Move WLED num-strings from pmi8994 to sony-xperia-tone
+    - arm64: dts: qcom: pmi8994: Add missing OVP interrupt
+    - drm/etnaviv: fix dumping of active MMU context
+    - x86/mm: Fix PAT bit missing from page protection modify mask
+    - ARM: dts: s3c64xx: align pinctrl with dtschema
+    - ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)
+    - ARM: dts: s5pv210: add dummy 5V regulator for backlight on SMDKv210
+    - ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)
+    - drm: adv7511: Fix low refresh rate register for ADV7533/5
+    - ARM: dts: BCM53573: Fix Ethernet info for Luxul devices
+    - arm64: dts: qcom: sdm845: Add missing RPMh power domain to GCC
+    - arm64: dts: qcom: sdm845: Fix the min frequency of "ice_core_clk"
+    - drm/amdgpu: Update min() to min_t() in 'amdgpu_info_ioctl'
+    - md/raid10: factor out dereference_rdev_and_rrdev()
+    - md/raid10: use dereference_rdev_and_rrdev() to get devices
+    - md/bitmap: don't set max_write_behind if there is no write mostly device
+    - md/md-bitmap: hold 'reconfig_mutex' in backlog_store()
+    - drm/msm: Update dev core dump to not print backwards
+    - drm/tegra: dpaux: Fix incorrect return value of platform_get_irq
+    - of: unittest: fix null pointer dereferencing in
+      of_unittest_find_node_by_name()
+    - arm64: dts: qcom: sm8150: Fix the I2C7 interrupt
+    - drm/armada: Fix off-by-one error in armada_overlay_get_property()
+    - drm/panel: simple: Add missing connector type and pixel format for AUO
+      T215HVN01
+    - ima: Remove deprecated IMA_TRUSTED_KEYRING Kconfig
+    - [Config] updateconfigs for IMA_TRUSTED_KEYRING
+    - drm: xlnx: zynqmp_dpsub: Add missing check for dma_set_mask
+    - drm/msm/mdp5: Don't leak some plane state
+    - firmware: meson_sm: fix to avoid potential NULL pointer dereference
+    - smackfs: Prevent underflow in smk_set_cipso()
+    - drm/amd/pm: fix variable dereferenced issue in amdgpu_device_attr_create()
+    - drm/msm/a2xx: Call adreno_gpu_init() earlier
+    - audit: fix possible soft lockup in __audit_inode_child()
+    - io_uring: fix drain stalls by invalid SQE
+    - bus: ti-sysc: Fix build warning for 64-bit build
+    - drm/mediatek: Remove freeing not dynamic allocated memory
+    - drm/mediatek: Fix potential memory leak if vmap() fail
+    - arm64: dts: qcom: apq8016-sbc: Fix ov5640 regulator supply names
+    - bus: ti-sysc: Fix cast to enum warning
+    - md: Set MD_BROKEN for RAID1 and RAID10
+    - md: add error_handlers for raid0 and linear
+    - md/raid0: Factor out helper for mapping and submitting a bio
+    - md/raid0: Fix performance regression for large sequential writes
+    - md: raid0: account for split bio in iostat accounting
+    - of: overlay: Call of_changeset_init() early
+    - of: unittest: Fix overlay type in apply/revert check
+    - ALSA: ac97: Fix possible error value of *rac97
+    - ipmi:ssif: Add check for kstrdup
+    - ipmi:ssif: Fix a memory leak when scanning for an adapter
+    - drivers: clk: keystone: Fix parameter judgment in _of_pll_clk_init()
+    - clk: sunxi-ng: Modify mismatched function name
+    - clk: qcom: gcc-sc7180: Fix up gcc_sdcc2_apps_clk_src
+    - EDAC/igen6: Fix the issue of no error events
+    - ext4: correct grp validation in ext4_mb_good_group
+    - ext4: avoid potential data overflow in next_linear_group
+    - clk: qcom: gcc-sm8250: Fix gcc_sdcc2_apps_clk_src
+    - clk: qcom: reset: Use the correct type of sleep/delay based on length
+    - clk: qcom: gcc-sm6350: Fix gcc_sdcc2_apps_clk_src
+    - PCI: microchip: Correct the DED and SEC interrupt bit offsets
+    - PCI: Mark NVIDIA T4 GPUs to avoid bus reset
+    - pinctrl: mcp23s08: check return value of devm_kasprintf()
+    - PCI: pciehp: Use RMW accessors for changing LNKCTL
+    - PCI/ASPM: Use RMW accessors for changing LNKCTL
+    - clk: imx8mp: fix sai4 clock
+    - clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
+    - powerpc/radix: Move some functions into #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
+    - vfio/type1: fix cap_migration information leak
+    - powerpc/fadump: reset dump area size if fadump memory reserve fails
+    - powerpc/perf: Convert fsl_emb notifier to state machine callbacks
+    - drm/amdgpu: Use RMW accessors for changing LNKCTL
+    - drm/radeon: Use RMW accessors for changing LNKCTL
+    - net/mlx5: Use RMW accessors for changing LNKCTL
+    - wifi: ath11k: Use RMW accessors for changing LNKCTL
+    - wifi: ath10k: Use RMW accessors for changing LNKCTL
+    - PCI: dwc: Add start_link/stop_link inlines
+    - PCI: layerscape: Add the endpoint linkup notifier support
+    - PCI: layerscape: Add workaround for lost link capabilities during reset
+    - powerpc: Don't include lppaca.h in paca.h
+    - powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
+    - nfs/blocklayout: Use the passed in gfp flags
+    - powerpc/iommu: Fix notifiers being shared by PCI and VIO buses
+    - ext4: fix unttached inode after power cut with orphan file feature enabled
+    - jfs: validate max amount of blocks before allocation.
+    - fs: lockd: avoid possible wrong NULL parameter
+    - NFSD: da_addr_body field missing in some GETDEVICEINFO replies
+    - NFS: Guard against READDIR loop when entry names exceed MAXNAMELEN
+    - NFSv4.2: fix handling of COPY ERR_OFFLOAD_NO_REQ
+    - pNFS: Fix assignment of xprtdata.cred
+    - RDMA/qedr: Remove a duplicate assignment in irdma_query_ah()
+    - media: ad5820: Drop unsupported ad5823 from i2c_ and of_device_id tables
+    - media: i2c: tvp5150: check return value of devm_kasprintf()
+    - media: v4l2-core: Fix a potential resource leak in v4l2_fwnode_parse_link()
+    - iommu/amd/iommu_v2: Fix pasid_state refcount dec hit 0 warning on pasid
+      unbind
+    - iommu: rockchip: Fix directory table address encoding
+    - drivers: usb: smsusb: fix error handling code in smsusb_init_device
+    - media: dib7000p: Fix potential division by zero
+    - media: dvb-usb: m920x: Fix a potential memory leak in m920x_i2c_xfer()
+    - media: cx24120: Add retval check for cx24120_message_send()
+    - scsi: hisi_sas: Modify v3 HW SSP underflow error processing
+    - scsi: hisi_sas: Modify v3 HW SATA completion error processing
+    - scsi: hisi_sas: Fix warnings detected by sparse
+    - scsi: hisi_sas: Fix normally completed I/O analysed as failed
+    - media: rkvdec: increase max supported height for H.264
+    - media: mediatek: vcodec: Return NULL if no vdec_fb is found
+    - usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()
+    - scsi: RDMA/srp: Fix residual handling
+    - scsi: iscsi: Rename iscsi_set_param() to iscsi_if_set_param()
+    - scsi: iscsi: Add length check for nlattr payload
+    - scsi: iscsi: Add strlen() check in iscsi_if_set{_host}_param()
+    - scsi: be2iscsi: Add length check when parsing nlattrs
+    - scsi: qla4xxx: Add length check when parsing nlattrs
+    - serial: sprd: Assign sprd_port after initialized to avoid wrong access
+    - serial: sprd: Fix DMA buffer leak issue
+    - x86/APM: drop the duplicate APM_MINOR_DEV macro
+    - scsi: qedf: Do not touch __user pointer in
+      qedf_dbg_stop_io_on_error_cmd_read() directly
+    - scsi: qedf: Do not touch __user pointer in qedf_dbg_debug_cmd_read()
+      directly
+    - scsi: qedf: Do not touch __user pointer in qedf_dbg_fp_int_cmd_read()
+      directly
+    - RDMA/irdma: Replace one-element array with flexible-array member
+    - coresight: tmc: Explicit type conversions to prevent integer overflow
+    - dma-buf/sync_file: Fix docs syntax
+    - driver core: test_async: fix an error code
+    - iommu/sprd: Add missing force_aperture
+    - RDMA/hns: Fix port active speed
+    - RDMA/hns: Fix incorrect post-send with direct wqe of wr-list
+    - RDMA/hns: Fix CQ and QP cache affinity
+    - IB/uverbs: Fix an potential error pointer dereference
+    - fsi: aspeed: Reset master errors after CFAM reset
+    - iommu/qcom: Disable and reset context bank before programming
+    - iommu/vt-d: Fix to flush cache of PASID directory table
+    - platform/x86: dell-sysman: Fix reference leak
+    - media: go7007: Remove redundant if statement
+    - media: venus: hfi_venus: Only consider sys_idle_indicator on V1
+    - USB: gadget: f_mass_storage: Fix unused variable warning
+    - media: ov5640: Enable MIPI interface in ov5640_set_power_mipi()
+    - media: i2c: ov2680: Set V4L2_CTRL_FLAG_MODIFY_LAYOUT on flips
+    - media: ov2680: Remove auto-gain and auto-exposure controls
+    - media: ov2680: Fix ov2680_bayer_order()
+    - media: ov2680: Fix vflip / hflip set functions
+    - media: ov2680: Remove VIDEO_V4L2_SUBDEV_API ifdef-s
+    - media: ov2680: Don't take the lock for try_fmt calls
+    - media: ov2680: Add ov2680_fill_format() helper function
+    - media: ov2680: Fix ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY not
+      working
+    - media: ov2680: Fix regulators being left enabled on ov2680_power_on() errors
+    - media: i2c: rdacm21: Fix uninitialized value
+    - cgroup:namespace: Remove unused cgroup_namespaces_init()
+    - scsi: core: Use 32-bit hostnum in scsi_host_lookup()
+    - scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock
+    - serial: tegra: handle clk prepare error in tegra_uart_hw_init()
+    - amba: bus: fix refcount leak
+    - Revert "IB/isert: Fix incorrect release of isert connection"
+    - HID: logitech-dj: Fix error handling in logi_dj_recv_switch_to_dj_mode()
+    - HID: multitouch: Correct devm device reference for hidinput input_dev name
+    - x86/speculation: Mark all Skylake CPUs as vulnerable to GDS
+    - tracing: Remove extra space at the end of hwlat_detector/mode
+    - tracing: Fix race issue between cpu buffer write and swap
+    - mtd: rawnand: brcmnand: Fix mtd oobsize
+    - phy/rockchip: inno-hdmi: use correct vco_div_5 macro on rk3328
+    - phy/rockchip: inno-hdmi: round fractal pixclock in rk3328 recalc_rate
+    - phy/rockchip: inno-hdmi: do not power on rk3328 post pll on reg write
+    - rpmsg: glink: Add check for kstrdup
+    - leds: pwm: Fix error code in led_pwm_create_fwnode()
+    - leds: multicolor: Use rounded division when calculating color components
+    - leds: trigger: tty: Do not use LED_ON/OFF constants, use
+      led_blink_set_oneshot instead
+    - mtd: spi-nor: Check bus width while setting QE bit
+    - mtd: rawnand: fsmc: handle clk prepare error in fsmc_nand_resume()
+    - um: Fix hostaudio build errors
+    - dmaengine: ste_dma40: Add missing IRQ check in d40_probe
+    - cpufreq: Fix the race condition while updating the transition_task of policy
+    - virtio_ring: fix avail_wrap_counter in virtqueue_add_packed
+    - skbuff: skb_segment, Call zero copy functions before using skbuff frags
+    - PM / devfreq: Fix leak in devfreq_dev_release()
+    - ALSA: pcm: Fix missing fixup call in compat hw_refine ioctl
+    - rcu: dump vmalloc memory info safely
+    - printk: ringbuffer: Fix truncating buffer size min_t cast
+    - scsi: core: Fix the scsi_set_resid() documentation
+    - mm/vmalloc: add a safer version of find_vm_area() for debug
+    - media: i2c: ccs: Check rules is non-NULL
+    - PCI: rockchip: Use 64-bit mask on MSI 64-bit PCI address
+    - ipmi_si: fix a memleak in try_smi_init()
+    - ARM: OMAP2+: Fix -Warray-bounds warning in _pwrdm_state_switch()
+    - backlight/gpio_backlight: Compare against struct fb_info.device
+    - backlight/bd6107: Compare against struct fb_info.device
+    - backlight/lv5207lp: Compare against struct fb_info.device
+    - xtensa: PMU: fix base address for the newer hardware
+    - i3c: master: svc: fix probe failure when no i3c device exist
+    - arm64: csum: Fix OoB access in IP checksum code for negative lengths
+    - media: dvb: symbol fixup for dvb_attach()
+    - media: venus: hfi_venus: Write to VIDC_CTRL_INIT after unmasking interrupts
+    - Revert "scsi: qla2xxx: Fix buffer overrun"
+    - scsi: mpt3sas: Perform additional retries if doorbell read returns 0
+    - ntb: Drop packets when qp link is down
+    - ntb: Clean up tx tail index on link down
+    - ntb: Fix calculation ntb_transport_tx_free_entry()
+    - Revert "PCI: Mark NVIDIA T4 GPUs to avoid bus reset"
+    - procfs: block chmod on /proc/thread-self/comm
+    - parisc: Fix /proc/cpuinfo output for lscpu
+    - dlm: fix plock lookup when using multiple lockspaces
+    - dccp: Fix out of bounds access in DCCP error handler
+    - X.509: if signature is unsupported skip validation
+    - net: handle ARPHRD_PPP in dev_is_mac_header_xmit()
+    - fsverity: skip PKCS#7 parser when keyring is empty
+    - mmc: renesas_sdhi: register irqs before registering controller
+    - pstore/ram: Check start of empty przs during init
+    - arm64: sdei: abort running SDEI handlers during crash
+    - s390/ipl: add missing secure/has_secure file to ipl type 'unknown'
+    - crypto: stm32 - fix loop iterating through scatterlist for DMA
+    - cpufreq: brcmstb-avs-cpufreq: Fix -Warray-bounds bug
+    - usb: typec: tcpm: set initial svdm version based on pd revision
+    - usb: typec: bus: verify partner exists in typec_altmode_attention
+    - x86/sgx: Break up long non-preemptible delays in sgx_vepc_release()
+    - perf/x86/uncore: Correct the number of CHAs on EMR
+    - tracing: Zero the pipe cpumask on alloc to avoid spurious -EBUSY
+    - md/md-bitmap: remove unnecessary local variable in backlog_store()
+    - udf: initialize newblock to 0
+    - net/ipv6: SKB symmetric hash should incorporate transport ports
+    - io_uring: always lock in io_apoll_task_func
+    - io_uring: break out of iowq iopoll on teardown
+    - io_uring: break iopolling on signal
+    - scsi: qla2xxx: Adjust IOCB resource on qpair create
+    - scsi: qla2xxx: Limit TMF to 8 per function
+    - scsi: qla2xxx: Fix deletion race condition
+    - scsi: qla2xxx: fix inconsistent TMF timeout
+    - scsi: qla2xxx: Fix command flush during TMF
+    - scsi: qla2xxx: Fix erroneous link up failure
+    - scsi: qla2xxx: Turn off noisy message log
+    - scsi: qla2xxx: Fix session hang in gnl
+    - scsi: qla2xxx: Fix TMF leak through
+    - scsi: qla2xxx: Remove unsupported ql2xenabledif option
+    - scsi: qla2xxx: Flush mailbox commands on chip reset
+    - scsi: qla2xxx: Fix smatch warn for qla_init_iocb_limit()
+    - scsi: qla2xxx: Error code did not return to upper layer
+    - scsi: qla2xxx: Fix firmware resource tracking
+    - fbdev/ep93xx-fb: Do not assign to struct fb_info.dev
+    - clk: qcom: camcc-sc7180: fix async resume during probe
+    - drm/ast: Fix DRAM init on AST2200
+    - clk: qcom: turingcc-qcs404: fix missing resume during probe
+    - lib/test_meminit: allocate pages up to order MAX_ORDER
+    - parisc: led: Fix LAN receive and transmit LEDs
+    - parisc: led: Reduce CPU overhead for disk & lan LED computation
+    - pinctrl: cherryview: fix address_space_handler() argument
+    - dt-bindings: clock: xlnx,versal-clk: drop select:false
+    - clk: qcom: gcc-mdm9615: use proper parent for pll0_vote clock
+    - soc: qcom: qmi_encdec: Restrict string length in decode
+    - clk: qcom: q6sstop-qcs404: fix missing resume during probe
+    - clk: qcom: mss-sc7180: fix missing resume during probe
+    - NFS: Fix a potential data corruption
+    - NFSv4/pnfs: minor fix for cleanup path in nfs4_get_device_info
+    - bus: mhi: host: Skip MHI reset if device is in RDDM
+    - kbuild: do not run depmod for 'make modules_sign'
+    - gfs2: Switch to wait_event in gfs2_logd
+    - gfs2: low-memory forced flush fixes
+    - kconfig: fix possible buffer overflow
+    - perf trace: Use zfree() to reduce chances of use after free
+    - perf trace: Really free the evsel->priv area
+    - pwm: atmel-tcb: Convert to platform remove callback returning void
+    - pwm: atmel-tcb: Harmonize resource allocation order
+    - pwm: atmel-tcb: Fix resource freeing in error path and remove
+    - backlight: gpio_backlight: Drop output GPIO direction check for initial
+      power state
+    - Input: tca6416-keypad - always expect proper IRQ number in i2c client
+    - Input: tca6416-keypad - fix interrupt enable disbalance
+    - perf annotate bpf: Don't enclose non-debug code with an assert()
+    - x86/virt: Drop unnecessary check on extended CPUID level in cpu_has_svm()
+    - perf vendor events: Update the JSON/events descriptions for power10 platform
+    - perf vendor events: Drop some of the JSON/events for power10 platform
+    - perf top: Don't pass an ERR_PTR() directly to perf_session__delete()
+    - watchdog: intel-mid_wdt: add MODULE_ALIAS() to allow auto-load
+    - pwm: lpc32xx: Remove handling of PWM channels
+    - net/sched: fq_pie: avoid stalls in fq_pie_timer()
+    - sctp: annotate data-races around sk->sk_wmem_queued
+    - ipv4: annotate data-races around fi->fib_dead
+    - net: read sk->sk_family once in sk_mc_loop()
+    - net: fib: avoid warn splat in flow dissector
+    - xsk: Fix xsk_diag use-after-free error during socket cleanup
+    - drm/i915/gvt: Drop unused helper intel_vgpu_reset_gtt()
+    - ipv4: ignore dst hint for multipath routes
+    - igb: disable virtualization features on 82580
+    - veth: Fixing transmit return status for dropped packets
+    - net: ipv6/addrconf: avoid integer underflow in ipv6_create_tempaddr
+    - net: phy: micrel: Correct bit assignments for phy_device flags
+    - af_unix: Fix data-races around user->unix_inflight.
+    - af_unix: Fix data-race around unix_tot_inflight.
+    - af_unix: Fix data-races around sk->sk_shutdown.
+    - af_unix: Fix data race around sk->sk_err.
+    - kcm: Destroy mutex in kcm_exit_net()
+    - octeontx2-af: Fix truncation of smq in CN10K NIX AQ enqueue mbox handler
+    - igc: Change IGC_MIN to allow set rx/tx value between 64 and 80
+    - igbvf: Change IGBVF_MIN to allow set rx/tx value between 64 and 80
+    - igb: Change IGB_MIN to allow set rx/tx value between 64 and 80
+    - s390/zcrypt: don't leak memory if dev_set_name() fails
+    - idr: fix param name in idr_alloc_cyclic() doc
+    - ip_tunnels: use DEV_STATS_INC()
+    - net: dsa: sja1105: fix bandwidth discrepancy between tc-cbs software and
+      offload
+    - net: dsa: sja1105: fix -ENOSPC when replacing the same tc-cbs too many times
+    - net: dsa: sja1105: complete tc-cbs offload support on SJA1110
+    - net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
+    - net: hns3: fix debugfs concurrency issue between kfree buffer and read
+    - net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
+    - net: hns3: fix the port information display when sfp is absent
+    - net: hns3: remove GSO partial feature bit
+    - sh: boards: Fix CEU buffer size passed to dma_declare_coherent_memory()
+    - net/mlx5: Free IRQ rmap and notifier on kernel shutdown
+    - ARC: atomics: Add compiler barrier to atomic operations...
+    - dmaengine: sh: rz-dmac: Fix destination and source data size setting
+    - jbd2: fix checkpoint cleanup performance regression
+    - jbd2: check 'jh->b_transaction' before removing it from checkpoint
+    - ext4: add correct group descriptors and reserved GDT blocks to system zone
+    - lib: test_scanf: Add explicit type cast to result initialization in
+      test_number_prefix()
+    - ata: pata_falcon: fix IO base selection for Q40
+    - ata: sata_gemini: Add missing MODULE_DESCRIPTION
+    - ata: pata_ftide010: Add missing MODULE_DESCRIPTION
+    - fuse: nlookup missing decrement in fuse_direntplus_link
+    - btrfs: free qgroup rsv on io failure
+    - btrfs: don't start transaction when joining with TRANS_JOIN_NOSTART
+    - btrfs: use the correct superblock to compare fsid in btrfs_validate_super
+    - mtd: rawnand: brcmnand: Fix crash during the panic_write
+    - mtd: rawnand: brcmnand: Fix potential out-of-bounds access in oob write
+    - mtd: rawnand: brcmnand: Fix potential false time out warning
+    - drm/amd/display: prevent potential division by zero errors
+    - MIPS: Fix CONFIG_CPU_DADDI_WORKAROUNDS `modules_install' regression
+    - perf hists browser: Fix hierarchy mode header
+    - perf tools: Handle old data in PERF_RECORD_ATTR
+    - perf hists browser: Fix the number of entries for 'e' key
+    - pcd: move the identify buffer into pcd_identify
+    - pcd: cleanup initialization
+    - block: move GENHD_FL_NATIVE_CAPACITY to disk->state
+    - block: move GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE to disk->event_flags
+    - block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART
+    - block: don't add or resize partition on the disk with GENHD_FL_NO_PART
+    - ARM: dts: samsung: exynos4210-i9100: Fix LCD screen's physical size
+    - ARM: dts: BCM5301X: Extend RAM to full 256MB for Linksys EA6500 V2
+    - net: ipv4: fix one memleak in __inet_del_ifa()
+    - kselftest/runner.sh: Propagate SIGTERM to runner child
+    - net/smc: use smc_lgr_list.lock to protect smc_lgr_list.list iterate in
+      smcr_port_add
+    - net: ethernet: mvpp2_main: fix possible OOB write in
+      mvpp2_ethtool_get_rxnfc()
+    - net: ethernet: mtk_eth_soc: fix possible NULL pointer dereference in
+      mtk_hwlro_get_fdir_all()
+    - hsr: Fix uninit-value access in fill_frame_info()
+    - net: dsa: sja1105: hide all multicast addresses from "bridge fdb show"
+    - r8152: check budget for r8152_poll()
+    - kcm: Fix memory leak in error path of kcm_sendmsg()
+    - platform/mellanox: mlxbf-tmfifo: Drop the Rx packet if no more descriptors
+    - platform/mellanox: mlxbf-tmfifo: Drop jumbo frames
+    - platform/mellanox: mlxbf-pmc: Fix potential buffer overflows
+    - platform/mellanox: mlxbf-pmc: Fix reading of unprogrammed events
+    - ipv6: fix ip6_sock_set_addr_preferences() typo
+    - ixgbe: fix timestamp configuration code
+    - kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
+    - MIPS: Only fiddle with CHECKFLAGS if `need-compiler'
+    - drm/amd/display: Fix a bug when searching for insert_above_mpcc
+    - pcd: fix error codes in pcd_init_unit()
+    - Linux 5.15.132
+  * CVE-2023-6176
+    - net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
+  * CVE-2023-6039
+    - timers: Use del_timer_sync() even on UP
+    - timers: Update kernel-doc for various functions
+    - timers: Rename del_timer_sync() to timer_delete_sync()
+    - timers: Rename del_timer() to timer_delete()
+    - timers: Split [try_to_]del_timer[_sync]() to prepare for shutdown mode
+    - timers: Add shutdown mechanism to the internal functions
+    - timers: Provide timer_shutdown[_sync]()
+    - clocksource/drivers/arm_arch_timer: Do not use timer namespace for
+      timer_shutdown() function
+    - clocksource/drivers/sp804: Do not use timer namespace for timer_shutdown()
+      function
+    - ARM: spear: Do not use timer namespace for timer_shutdown() function
+    - net: usb: lan78xx: reorder cleanup operations to avoid UAF bugs
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 21 Feb 2024 13:19:46 +1000
+
+linux-xilinx-zynqmp (5.15.0-1026.30) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1026.30 -proposed tracker (LP: #2049802)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] remove helper scripts
+    - debian/dkms-versions -- update from kernel-versions (main/d2024.01.02)
+
+  * Enable symbols for all Xilinx device trees (LP: #2049442)
+    - SAUCE: arm64: dts: Enable symbols for all Xilinx device trees
+
+  * Turn off non-zynqmp arch support (LP: #2044554)
+    - [Config] Turn off non-zynqmp arch support
+    - [Packaging] Update new baseline abi checks
+
+  * Add support for KD240 platform (LP: #2046280)
+    - Sync KD240 DTS from xlnx_rebase_v6.1_LTS
+    - can: xilinx_can: Add support for controller reset
+
+  [ Ubuntu: 5.15.0-92.102 ]
+
+  * jammy/linux: 5.15.0-92.102 -proposed tracker (LP: #2048614)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+  * CVE-2024-0193
+    - netfilter: nf_tables: skip set commit for deleted/destroyed sets
+  * CVE-2023-6040
+    - netfilter: nf_tables: Reject tables of unsupported family
+  * CVE-2023-6606
+    - smb: client: fix OOB in smbCalcSize()
+  * CVE-2023-6817
+    - netfilter: nft_set_pipapo: skip inactive elements during set walk
+  * CVE-2023-6932
+    - ipv4: igmp: fix refcnt uaf issue when receiving igmp query packet
+  * CVE-2023-6931
+    - perf/core: Add a new read format to get a number of lost samples
+    - perf: Fix perf_event_validate_size()
+    - perf: Fix perf_event_validate_size() lockdep splat
+
+  [ Ubuntu: 5.15.0-91.101 ]
+
+  * jammy/linux: 5.15.0-91.101 -proposed tracker (LP: #2043452)
+  * USB bus error after upgrading to proposed kernel on lunar and jammy
+    (LP: #2043197)
+    - USB: core: Fix oversight in SuperSpeed initialization
+
+  [ Ubuntu: 5.15.0-90.100 ]
+
+  * jammy/linux: 5.15.0-90.100 -proposed tracker (LP: #2041603)
+  * CVE-2023-25775
+    - RDMA/irdma: Remove irdma_uk_mw_bind()
+    - RDMA/irdma: Remove irdma_sc_send_lsmm_nostag()
+    - RDMA/irdma: Remove irdma_cqp_up_map_cmd()
+    - RDMA/irdma: Remove irdma_get_hw_addr()
+    - RDMA/irdma: Make irdma_uk_cq_init() return a void
+    - RDMA/irdma: optimize rx path by removing unnecessary copy
+    - RDMA/irdma: Remove enum irdma_status_code
+    - RDMA/irdma: Remove excess error variables
+    - RDMA/irdma: Prevent zero-length STAG registration
+  * CVE-2023-39189
+    - netfilter: nfnetlink_osf: avoid OOB read
+  * SMC stats: Wrong bucket calculation for payload of exactly 4096 bytes
+    (LP: #2039575)
+    - net/smc: Fix pos miscalculation in statistics
+  * CVE-2023-45871
+    - igb: set max size RX buffer when store bad packet is enabled
+  * CVE-2023-39193
+    - netfilter: xt_sctp: validate the flag_info count
+  * CVE-2023-39192
+    - netfilter: xt_u32: validate user space input
+  * CVE-2023-31085
+    - ubi: Refuse attaching if mtd's erasesize is 0
+  * CVE-2023-5717
+    - perf: Disallow mis-matched inherited group reads
+  * CVE-2023-5178
+    - nvmet-tcp: Fix a possible UAF in queue intialization setup
+  * CVE-2023-5158
+    - vringh: don't use vringh_kiov_advance() in vringh_iov_xfer()
+  * [SRU][J/L/M] UBUNTU: [Packaging] Make WWAN driver a loadable module
+    (LP: #2033406)
+    - [Packaging] Make WWAN driver loadable modules
+  * HP ProBook 450 G8 Notebook fail to wifi test (LP: #2037513)
+    - iwlwifi: mvm: Don't fail if PPAG isn't supported
+    - wifi: iwlwifi: fw: skip PPAG for JF
+  * usbip: error: failed to open /usr/share/hwdata//usb.ids (LP: #2039439)
+    - [Packaging] Make linux-tools-common depend on hwdata
+  * scripts/pahole-flags.sh change return to exit 0 (LP: #2035123)
+    - SAUCE: scripts/pahole-flags.sh change return to exit 0
+  * Unable to use nvme drive to install Ubuntu 23.10 (LP: #2040157)
+    - misc: rtsx: Fix some platforms can not boot and move the l1ss judgment to
+      probe
+  * Jammy update: v5.15.131 upstream stable release (LP: #2039610)
+    - erofs: ensure that the post-EOF tails are all zeroed
+    - ksmbd: fix wrong DataOffset validation of create context
+    - ksmbd: replace one-element array with flex-array member in struct
+      smb2_ea_info
+    - ARM: pxa: remove use of symbol_get()
+    - mmc: au1xmmc: force non-modular build and remove symbol_get usage
+    - net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index
+    - rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff
+    - modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules
+    - USB: serial: option: add Quectel EM05G variant (0x030e)
+    - USB: serial: option: add FOXCONN T99W368/T99W373 product
+    - ALSA: usb-audio: Fix init call orders for UAC1
+    - usb: dwc3: meson-g12a: do post init to fix broken usb after resumption
+    - usb: chipidea: imx: improve logic if samsung,picophy-* parameter is 0
+    - HID: wacom: remove the battery when the EKR is off
+    - staging: rtl8712: fix race condition
+    - Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race
+      condition
+    - wifi: mt76: mt7921: do not support one stream on secondary antenna only
+    - serial: qcom-geni: fix opp vote on shutdown
+    - serial: sc16is7xx: fix broken port 0 uart init
+    - serial: sc16is7xx: fix bug when first setting GPIO direction
+    - firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe
+    - fsi: master-ast-cf: Add MODULE_FIRMWARE macro
+    - tcpm: Avoid soft reset when partner does not support get_status
+    - nilfs2: fix general protection fault in nilfs_lookup_dirty_data_buffers()
+    - nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
+    - pinctrl: amd: Don't show `Invalid config param` errors
+    - usb: typec: tcpci: move tcpci.h to include/linux/usb/
+    - usb: typec: tcpci: clear the fault status bit
+    - Linux 5.15.131
+  * Jammy update: v5.15.130 upstream stable release (LP: #2039608)
+    - ACPI: thermal: Drop nocrt parameter
+    - module: Expose module_init_layout_section()
+    - arm64: module-plts: inline linux/moduleloader.h
+    - arm64: module: Use module_init_layout_section() to spot init sections
+    - ARM: module: Use module_init_layout_section() to spot init sections
+    - rcu: Prevent expedited GP from enabling tick on offline CPU
+    - rcu-tasks: Fix IPI failure handling in trc_wait_for_one_reader
+    - rcu-tasks: Wait for trc_read_check_handler() IPIs
+    - rcu-tasks: Add trc_inspect_reader() checks for exiting critical section
+    - Linux 5.15.130
+  * CVE-2023-42754
+    - ipv4: fix null-deref in ipv4_link_failure
+  * Jammy update: v5.15.129 upstream stable release (LP: #2039227)
+    - NFSv4.2: fix error handling in nfs42_proc_getxattr
+    - NFSv4: fix out path in __nfs4_get_acl_uncached
+    - xprtrdma: Remap Receive buffers after a reconnect
+    - PCI: acpiphp: Reassign resources on bridge if necessary
+    - dlm: improve plock logging if interrupted
+    - dlm: replace usage of found with dedicated list iterator variable
+    - fs: dlm: add pid to debug log
+    - fs: dlm: change plock interrupted message to debug again
+    - fs: dlm: use dlm_plock_info for do_unlock_close
+    - fs: dlm: fix mismatch of plock results from userspace
+    - MIPS: cpu-features: Enable octeon_cache by cpu_type
+    - MIPS: cpu-features: Use boot_cpu_type for CPU type based features
+    - fbdev: Improve performance of sys_imageblit()
+    - fbdev: Fix sys_imageblit() for arbitrary image widths
+    - fbdev: fix potential OOB read in fast_imageblit()
+    - ALSA: pcm: Fix potential data race at PCM memory allocation helpers
+    - jbd2: remove t_checkpoint_io_list
+    - jbd2: remove journal_clean_one_cp_list()
+    - jbd2: fix a race when checking checkpoint buffer busy
+    - can: raw: fix receiver memory leak
+    - drm/amd/display: do not wait for mpc idle if tg is disabled
+    - drm/amd/display: check TG is non-null before checking if enabled
+    - can: raw: fix lockdep issue in raw_release()
+    - tracing: Fix cpu buffers unavailable due to 'record_disabled' missed
+    - tracing: Fix memleak due to race between current_tracer and trace
+    - octeontx2-af: SDP: fix receive link config
+    - sock: annotate data-races around prot->memory_pressure
+    - dccp: annotate data-races in dccp_poll()
+    - ipvlan: Fix a reference count leak warning in ipvlan_ns_exit()
+    - net: bgmac: Fix return value check for fixed_phy_register()
+    - net: bcmgenet: Fix return value check for fixed_phy_register()
+    - net: validate veth and vxcan peer ifindexes
+    - ice: fix receive buffer size miscalculation
+    - igb: Avoid starting unnecessary workqueues
+    - igc: Fix the typo in the PTM Control macro
+    - net/sched: fix a qdisc modification with ambiguous command request
+    - netfilter: nf_tables: flush pending destroy work before netlink notifier
+    - netfilter: nf_tables: fix out of memory error handling
+    - rtnetlink: return ENODEV when ifname does not exist and group is given
+    - rtnetlink: Reject negative ifindexes in RTM_NEWLINK
+    - net: remove bond_slave_has_mac_rcu()
+    - bonding: fix macvlan over alb bond support
+    - net/ncsi: make one oem_gma function for all mfr id
+    - net/ncsi: change from ndo_set_mac_address to dev_set_mac_address
+    - ibmveth: Use dcbf rather than dcbfl
+    - NFSv4: Fix dropped lock for racing OPEN and delegation return
+    - clk: Fix slab-out-of-bounds error in devm_clk_release()
+    - ALSA: ymfpci: Fix the missing snd_card_free() call at probe error
+    - mm: add a call to flush_cache_vmap() in vmap_pfn()
+    - NFS: Fix a use after free in nfs_direct_join_group()
+    - nfsd: Fix race to FREE_STATEID and cl_revoked
+    - selinux: set next pointer before attaching to list
+    - batman-adv: Trigger events for auto adjusted MTU
+    - batman-adv: Don't increase MTU when set by user
+    - batman-adv: Do not get eth header before batadv_check_management_packet
+    - batman-adv: Fix TT global entry leak when client roamed back
+    - batman-adv: Fix batadv_v_ogm_aggr_send memory leak
+    - batman-adv: Hold rtnl lock during MTU update via netlink
+    - lib/clz_ctz.c: Fix __clzdi2() and __ctzdi2() for 32-bit kernels
+    - radix tree: remove unused variable
+    - of: unittest: Fix EXPECT for parse_phandle_with_args_map() test
+    - of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock
+    - media: vcodec: Fix potential array out-of-bounds in encoder queue_setup
+    - PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root
+      bus
+    - drm/vmwgfx: Fix shader stage validation
+    - drm/display/dp: Fix the DP DSC Receiver cap size
+    - x86/fpu: Invalidate FPU state correctly on exec()
+    - nfs: use vfs setgid helper
+    - nfsd: use vfs setgid helper
+    - torture: Fix hang during kthread shutdown phase
+    - cgroup/cpuset: Rename functions dealing with DEADLINE accounting
+    - sched/cpuset: Bring back cpuset_mutex
+    - sched/cpuset: Keep track of SCHED_DEADLINE task in cpusets
+    - cgroup/cpuset: Iterate only if DEADLINE tasks are present
+    - sched/deadline: Create DL BW alloc, free & check overflow interface
+    - cgroup/cpuset: Free DL BW in case can_attach() fails
+    - drm/i915: Fix premature release of request's reusable memory
+    - can: raw: add missing refcount for memory leak fix
+    - scsi: snic: Fix double free in snic_tgt_create()
+    - scsi: core: raid_class: Remove raid_component_add()
+    - clk: Fix undefined reference to `clk_rate_exclusive_{get,put}'
+    - pinctrl: renesas: rza2: Add lock around
+      pinctrl_generic{{add,remove}_group,{add,remove}_function}
+    - dma-buf/sw_sync: Avoid recursive lock during fence signal
+    - mm: memory-failure: kill soft_offline_free_page()
+    - mm: memory-failure: fix unexpected return value in soft_offline_page()
+    - mm,ima,kexec,of: use memblock_free_late from ima_free_kexec_buffer
+    - Linux 5.15.129
+  * Jammy update: v5.15.128 upstream stable release (LP: #2038486)
+    - mmc: sdhci-f-sdh30: Replace with sdhci_pltfm
+    - selftests: forwarding: tc_actions: cleanup temporary files when test is
+      aborted
+    - selftests: forwarding: tc_actions: Use ncat instead of nc
+    - macsec: Fix traffic counters/statistics
+    - macsec: use DEV_STATS_INC()
+    - net/tls: Perform immediate device ctx cleanup when possible
+    - net/tls: Multi-threaded calls to TX tls_dev_del
+    - net: tls: avoid discarding data on record close
+    - PCI: tegra194: Fix possible array out of bounds access
+    - ARM: dts: imx6dl: prtrvt, prtvt7, prti6q, prtwd2: fix USB related warnings
+    - iopoll: Call cpu_relax() in busy loops
+    - ASoC: SOF: Intel: fix SoundWire/HDaudio mutual exclusion
+    - dma-remap: use kvmalloc_array/kvfree for larger dma memory remap
+    - HID: logitech-hidpp: Add USB and Bluetooth IDs for the Logitech G915 TKL
+      Keyboard
+    - HID: add quirk for 03f0:464a HP Elite Presenter Mouse
+    - RDMA/mlx5: Return the firmware result upon destroying QP/RQ
+    - ovl: check type and offset of struct vfsmount in ovl_entry
+    - smb: client: fix warning in cifs_smb3_do_mount()
+    - media: v4l2-mem2mem: add lock to protect parameter num_rdy
+    - usb: gadget: u_serial: Avoid spinlock recursion in __gs_console_push
+    - media: platform: mediatek: vpu: fix NULL ptr dereference
+    - thunderbolt: Read retimer NVM authentication status prior
+      tb_retimer_set_inbound_sbtx()
+    - usb: chipidea: imx: don't request QoS for imx8ulp
+    - usb: chipidea: imx: add missing USB PHY DPDM wakeup setting
+    - gfs2: Fix possible data races in gfs2_show_options()
+    - pcmcia: rsrc_nonstatic: Fix memory leak in nonstatic_release_resource_db()
+    - firewire: net: fix use after free in fwnet_finish_incoming_packet()
+    - watchdog: sp5100_tco: support Hygon FCH/SCH (Server Controller Hub)
+    - Bluetooth: L2CAP: Fix use-after-free
+    - Bluetooth: btusb: Add MT7922 bluetooth ID for the Asus Ally
+    - drm/amdgpu: Fix potential fence use-after-free v2
+    - fs/ntfs3: Enhance sanity check while generating attr_list
+    - fs: ntfs3: Fix possible null-pointer dereferences in mi_read()
+    - fs/ntfs3: Mark ntfs dirty when on-disk struct is corrupted
+    - ALSA: hda/realtek: Add quirks for Unis H3C Desktop B760 & Q760
+    - ALSA: hda: fix a possible null-pointer dereference due to data race in
+      snd_hdac_regmap_sync()
+    - powerpc/kasan: Disable KCOV in KASAN code
+    - ring-buffer: Do not swap cpu_buffer during resize process
+    - iio: add addac subdirectory
+    - iio: adc: stx104: Utilize iomap interface
+    - iio: adc: stx104: Implement and utilize register structures
+    - iio: stx104: Move to addac subdirectory
+    - iio: addac: stx104: Fix race condition for stx104_write_raw()
+    - iio: addac: stx104: Fix race condition when converting analog-to-digital
+    - igc: read before write to SRRCTL register
+    - ARM: dts: aspeed: asrock: Correct firmware flash SPI clocks
+    - drm/amd/display: save restore hdcp state when display is unplugged from mst
+      hub
+    - drm/amd/display: phase3 mst hdcp for multiple displays
+    - drm/amd/display: fix access hdcp_workqueue assert
+    - usb: dwc3: gadget: Synchronize IRQ between soft connect/disconnect
+    - usb: dwc3: Remove DWC3 locking during gadget suspend/resume
+    - usb: dwc3: Fix typos in gadget.c
+    - USB: dwc3: gadget: drop dead hibernation code
+    - usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()
+    - tty: serial: fsl_lpuart: Add i.MXRT1050 support
+    - tty: serial: fsl_lpuart: make rx_watermark configurable for different
+      platforms
+    - tty: serial: fsl_lpuart: reduce RX watermark to 0 on LS1028A
+    - USB: dwc3: qcom: fix NULL-deref on suspend
+    - USB: dwc3: fix use-after-free on core driver unbind
+    - mmc: bcm2835: fix deferred probing
+    - mmc: sunxi: fix deferred probing
+    - ARM: dts: imx6sll: fixup of operating points
+    - ARM: dts: nxp/imx6sll: fix wrong property name in usbphy node
+    - btrfs: move out now unused BG from the reclaim list
+    - virtio-mmio: don't break lifecycle of vm_dev
+    - vduse: Use proper spinlock for IRQ injection
+    - cifs: fix potential oops in cifs_oplock_break
+    - i2c: bcm-iproc: Fix bcm_iproc_i2c_isr deadlock issue
+    - i2c: hisi: Only handle the interrupt of the driver's transfer
+    - fbdev: mmp: fix value check in mmphw_probe()
+    - powerpc/rtas_flash: allow user copy to flash block cache objects
+    - tty: n_gsm: fix the UAF caused by race condition in gsm_cleanup_mux
+    - tty: serial: fsl_lpuart: Clear the error flags by writing 1 for lpuart32
+      platforms
+    - btrfs: fix BUG_ON condition in btrfs_cancel_balance
+    - i2c: designware: Correct length byte validation logic
+    - i2c: designware: Handle invalid SMBus block data response length value
+    - net: xfrm: Fix xfrm_address_filter OOB read
+    - net: af_key: fix sadb_x_filter validation
+    - net: xfrm: Amend XFRMA_SEC_CTX nla_policy structure
+    - xfrm: fix slab-use-after-free in decode_session6
+    - ip6_vti: fix slab-use-after-free in decode_session6
+    - ip_vti: fix potential slab-use-after-free in decode_session6
+    - xfrm: add forgotten nla_policy for XFRMA_MTIMER_THRESH
+    - net: phy: fix IRQ-based wake-on-lan over hibernate / power off
+    - selftests: mirror_gre_changes: Tighten up the TTL test match
+    - drm/panel: simple: Fix AUO G121EAN01 panel timings according to the docs
+    - netfilter: nf_tables: fix false-positive lockdep splat
+    - ipvs: fix racy memcpy in proc_do_sync_threshold
+    - net: phy: broadcom: stub c45 read/write for 54810
+    - team: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
+    - iavf: fix FDIR rule fields masks validation
+    - i40e: fix misleading debug logs
+    - net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset
+    - sock: Fix misuse of sk_under_memory_pressure()
+    - net: do not allow gso_size to be set to GSO_BY_FRAGS
+    - bus: ti-sysc: Flush posted write on enable before reset
+    - arm64: dts: qcom: qrb5165-rb5: fix thermal zone conflict
+    - ARM: dts: imx: Set default tuning step for imx6sx usdhc
+    - ASoC: rt5665: add missed regulator_bulk_disable
+    - ASoC: meson: axg-tdm-formatter: fix channel slot allocation
+    - soc: aspeed: socinfo: Add kfree for kstrdup
+    - ALSA: hda/realtek - Remodified 3k pull low procedure
+    - riscv: uaccess: Return the number of bytes effectively not copied
+    - serial: 8250: Fix oops for port->pm on uart_change_pm()
+    - ALSA: usb-audio: Add support for Mythware XA001AU capture and playback
+      interfaces.
+    - cifs: Release folio lock on fscache read hit.
+    - mmc: wbsd: fix double mmc_free_host() in wbsd_init()
+    - mmc: block: Fix in_flight[issue_type] value error
+    - drm/qxl: fix UAF on handle creation
+    - drm/amd: flush any delayed gfxoff on suspend entry
+    - netfilter: set default timeout to 3 secs for sctp shutdown send and recv
+      state
+    - arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4
+    - virtio-net: set queues after driver_ok
+    - net: fix the RTO timer retransmitting skb every 1ms if linear option is
+      enabled
+    - mmc: f-sdh30: fix order of function calls in sdhci_f_sdh30_remove
+    - Linux 5.15.128
+  * Jammy update: v5.15.127 upstream stable release (LP: #2038382)
+    - ksmbd: validate command request size
+    - ksmbd: fix wrong next length validation of ea buffer in smb2_set_ea()
+    - wireguard: allowedips: expand maximum node depth
+    - mmc: moxart: read scr register without changing byte order
+    - ipv6: adjust ndisc_is_useropt() to also return true for PIO
+    - dmaengine: pl330: Return DMA_PAUSED when transaction is paused
+    - riscv,mmio: Fix readX()-to-delay() ordering
+    - drm/nouveau/gr: enable memory loads on helper invocation on all channels
+    - drm/shmem-helper: Reset vma->vm_ops before calling dma_buf_mmap()
+    - drm/amd/display: check attr flag before set cursor degamma on DCN3+
+    - hwmon: (pmbus/bel-pfe) Enable PMBUS_SKIP_STATUS_CHECK for pfe1100
+    - radix tree test suite: fix incorrect allocation size for pthreads
+    - nilfs2: fix use-after-free of nilfs_root in dirtying inodes via iput
+    - bpf: allow precision tracking for programs with subprogs
+    - bpf: stop setting precise in current state
+    - bpf: aggressively forget precise markings during state checkpointing
+    - selftests/bpf: make test_align selftest more robust
+    - selftests/bpf: Workaround verification failure for
+      fexit_bpf2bpf/func_replace_return_code
+    - selftests/bpf: Fix sk_assign on s390x
+    - io_uring: correct check for O_TMPFILE
+    - iio: cros_ec: Fix the allocation size for cros_ec_command
+    - iio: adc: ina2xx: avoid NULL pointer dereference on OF device match
+    - binder: fix memory leak in binder_init()
+    - misc: rtsx: judge ASPM Mode to set PETXCFG Reg
+    - usb-storage: alauda: Fix uninit-value in alauda_check_media()
+    - usb: dwc3: Properly handle processing of pending events
+    - usb: common: usb-conn-gpio: Prevent bailing out if initial role is none
+    - usb: typec: tcpm: Fix response to vsafe0V event
+    - x86/cpu/amd: Enable Zenbleed fix for AMD Custom APU 0405
+    - x86/mm: Fix VDSO and VVAR placement on 5-level paging machines
+    - x86/speculation: Add cpu_show_gds() prototype
+    - x86: Move gds_ucode_mitigated() declaration to header
+    - drm/nouveau/disp: Revert a NULL check inside nouveau_connector_get_modes
+    - selftests/rseq: Fix build with undefined __weak
+    - selftests: forwarding: Add a helper to skip test when using veth pairs
+    - selftests: forwarding: ethtool: Skip when using veth pairs
+    - selftests: forwarding: ethtool_extended_state: Skip when using veth pairs
+    - selftests: forwarding: Skip test when no interfaces are specified
+    - selftests: forwarding: Switch off timeout
+    - selftests: forwarding: tc_flower: Relax success criterion
+    - net: core: remove unnecessary frame_sz check in bpf_xdp_adjust_tail()
+    - bpf, sockmap: Fix map type error in sock_map_del_link
+    - bpf, sockmap: Fix bug that strp_done cannot be called
+    - mISDN: Update parameter type of dsp_cmx_send()
+    - net/packet: annotate data-races around tp->status
+    - tunnels: fix kasan splat when generating ipv4 pmtu error
+    - xsk: fix refcount underflow in error path
+    - bonding: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
+    - dccp: fix data-race around dp->dccps_mss_cache
+    - drivers: net: prevent tun_build_skb() to exceed the packet size limit
+    - iavf: fix potential races for FDIR filters
+    - IB/hfi1: Fix possible panic during hotplug remove
+    - drm/rockchip: Don't spam logs in atomic check
+    - wifi: cfg80211: fix sband iftype data lookup for AP_VLAN
+    - RDMA/umem: Set iova in ODP flow
+    - net: phy: at803x: remove set/get wol callbacks for AR8032
+    - net: hns3: refactor hclge_mac_link_status_wait for interface reuse
+    - net: hns3: add wait until mac link down
+    - nexthop: Fix infinite nexthop dump when using maximum nexthop ID
+    - nexthop: Make nexthop bucket dump more efficient
+    - nexthop: Fix infinite nexthop bucket dump when using maximum nexthop ID
+    - dmaengine: mcf-edma: Fix a potential un-allocated memory access
+    - net/mlx5: Allow 0 for total host VFs
+    - net/mlx5: Skip clock update work when device is in error state
+    - ibmvnic: Enforce stronger sanity checks on login response
+    - ibmvnic: Unmap DMA login rsp buffer on send login fail
+    - ibmvnic: Handle DMA unmapping of login buffs in release functions
+    - btrfs: don't stop integrity writeback too early
+    - btrfs: exit gracefully if reloc roots don't match
+    - btrfs: reject invalid reloc tree root keys with stack dump
+    - btrfs: set cache_block_group_error if we find an error
+    - nvme-tcp: fix potential unbalanced freeze & unfreeze
+    - nvme-rdma: fix potential unbalanced freeze & unfreeze
+    - netfilter: nf_tables: report use refcount overflow
+    - scsi: core: Fix legacy /proc parsing buffer overflow
+    - scsi: storvsc: Fix handling of virtual Fibre Channel timeouts
+    - scsi: 53c700: Check that command slot is not NULL
+    - scsi: snic: Fix possible memory leak if device_add() fails
+    - scsi: core: Fix possible memory leak if device_add() fails
+    - scsi: fnic: Replace return codes in fnic_clean_pending_aborts()
+    - scsi: qedi: Fix firmware halt over suspend and resume
+    - scsi: qedf: Fix firmware halt over suspend and resume
+    - alpha: remove __init annotation from exported page_is_ram()
+    - sch_netem: fix issues in netem_change() vs get_dist_table()
+    - tick: Detect and fix jiffies update stall
+    - timers/nohz: Switch to ONESHOT_STOPPED in the low-res handler when the tick
+      is stopped
+    - timers/nohz: Last resort update jiffies on nohz_full IRQ entry
+    - Linux 5.15.127
+    - Upstream stable to v5.15.127
+  * CVE-2023-37453
+    - USB: core: Unite old scheme and new scheme descriptor reads
+    - USB: core: Change usb_get_device_descriptor() API
+    - USB: core: Fix race by not overwriting udev->descriptor in hub_port_init()
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 19 Jan 2024 12:03:51 +1000
+
+linux-xilinx-zynqmp (5.15.0-1025.29) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1025.29 -proposed tracker (LP: #2036376)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+    - debian/dkms-versions -- update from kernel-versions (main/d2023.10.10)
+
+  * Jammy update: v5.15.117 upstream stable release (LP: #2030107)
+    - [Config] updateconfigs for BLK_DEV_SX8
+
+  * Jammy update: v5.15.118 upstream stable release (LP: #2030239)
+    - [Config] updateconfigs for DECNET
+
+  * CVE-2023-42755
+    - [Config] remove NET_CLS_RSVP and NET_CLS_RSVP6
+
+  * Please enable Renesas RZ platform serial installer (LP: #2022361)
+    - [Config] Mark sh-sci as built-in
+
+  * Jammy update: v5.15.107 upstream stable release (LP: #2023320)
+    - [Config] updateconfigs for ns module merger
+
+  * Jammy update: v5.15.105 upstream stable release (LP: #2023230)
+    - [Config] updateconfigs for SERIAL_8250_ASPEED_VUART
+
+  * Add K24 device tree (LP: #2040354)
+    - SAUCE: arm64: zynqmp: Add K24 device trees
+    - SAUCE: arm64: dts: Build dtbs for k24 carrier board
+
+  * K26 QSPI MTD Definition Correction (LP: #2032972)
+    - arm64: zynqmp: Fix User MTD partition size
+
+  * Move experimental ubuntu drivers to staging (LP: #2036370)
+    - ubuntu/staging: Move out of tree Xilinx drivers into staging directory
+    - modpost: Add staging flag to drivers in ubuntu/staging
+
+  * [kr260] Kernel snap does not boot (LP: #2028505)
+    - Fix kernel snap to support KR260
+
+  [ Ubuntu: 5.15.0-88.98 ]
+
+  * jammy/linux: 5.15.0-88.98 -proposed tracker (LP: #2038055)
+  * CVE-2023-4244
+    - netfilter: nf_tables: don't skip expired elements during walk
+    - netfilter: nf_tables: adapt set backend to use GC transaction API
+    - netfilter: nft_set_hash: mark set element as dead when deleting from packet
+      path
+    - netfilter: nf_tables: GC transaction API to avoid race with control plane
+    - netfilter: nf_tables: remove busy mark and gc batch API
+    - netfilter: nf_tables: don't fail inserts if duplicate has expired
+    - netfilter: nf_tables: fix kdoc warnings after gc rework
+    - netfilter: nf_tables: fix GC transaction races with netns and netlink event
+      exit path
+    - netfilter: nf_tables: GC transaction race with netns dismantle
+    - netfilter: nf_tables: GC transaction race with abort path
+    - netfilter: nf_tables: use correct lock to protect gc_list
+    - netfilter: nf_tables: defer gc run if previous batch is still pending
+    - netfilter: nft_dynset: disallow object maps
+    - netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
+  * CVE-2023-42756
+    - netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
+  * CVE-2023-4623
+    - net/sched: sch_hfsc: Ensure inner classes have fsc curve
+  * PCI BARs larger than 128GB are disabled (LP: #2037403)
+    - PCI: Support BAR sizes up to 8TB
+  * Fix unstable audio at low levels on Thinkpad P1G4 (LP: #2037077)
+    - ALSA: hda/realtek - ALC287 I2S speaker platform support
+  * Check for changes relevant for security certifications (LP: #1945989)
+    - [Packaging] Add a new fips-checks script
+  * Jammy update: v5.15.126 upstream stable release (LP: #2037593)
+    - io_uring: gate iowait schedule on having pending requests
+    - perf: Fix function pointer case
+    - net/mlx5: Free irqs only on shutdown callback
+    - arm64: errata: Add workaround for TSB flush failures
+    - arm64: errata: Add detection for TRBE write to out-of-range
+    - [Config] updateconfigs for ARM64_ERRATUM_ and
+      ARM64_WORKAROUND_TSB_FLUSH_FAILURE
+    - iommu/arm-smmu-v3: Work around MMU-600 erratum 1076982
+    - iommu/arm-smmu-v3: Document MMU-700 erratum 2812531
+    - iommu/arm-smmu-v3: Add explicit feature for nesting
+    - iommu/arm-smmu-v3: Document nesting-related errata
+    - arm64: dts: imx8mn-var-som: add missing pull-up for onboard PHY reset pinmux
+    - word-at-a-time: use the same return type for has_zero regardless of
+      endianness
+    - KVM: s390: fix sthyi error handling
+    - wifi: cfg80211: Fix return value in scan logic
+    - net/mlx5: DR, fix memory leak in mlx5dr_cmd_create_reformat_ctx
+    - net/mlx5e: fix return value check in mlx5e_ipsec_remove_trailer()
+    - bpf: Add length check for SK_DIAG_BPF_STORAGE_REQ_MAP_FD parsing
+    - rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length
+    - net: dsa: fix value check in bcm_sf2_sw_probe()
+    - perf test uprobe_from_different_cu: Skip if there is no gcc
+    - net: sched: cls_u32: Fix match key mis-addressing
+    - mISDN: hfcpci: Fix potential deadlock on &hc->lock
+    - qed: Fix kernel-doc warnings
+    - qed: Fix scheduling in a tasklet while getting stats
+    - net: annotate data-races around sk->sk_max_pacing_rate
+    - net: add missing READ_ONCE(sk->sk_rcvlowat) annotation
+    - net: add missing READ_ONCE(sk->sk_sndbuf) annotation
+    - net: add missing READ_ONCE(sk->sk_rcvbuf) annotation
+    - net: add missing data-race annotations around sk->sk_peek_off
+    - net: add missing data-race annotation for sk_ll_usec
+    - net/sched: taprio: Limit TCA_TAPRIO_ATTR_SCHED_CYCLE_TIME to INT_MAX.
+    - bpf, cpumap: Handle skb as well when clean up ptr_ring
+    - bpf: sockmap: Remove preempt_disable in sock_map_sk_acquire
+    - net: ll_temac: Switch to use dev_err_probe() helper
+    - net: ll_temac: fix error checking of irq_of_parse_and_map()
+    - net: korina: handle clk prepare error in korina_probe()
+    - net: netsec: Ignore 'phy-mode' on SynQuacer in DT mode
+    - net: dcb: choose correct policy to parse DCB_ATTR_BCN
+    - s390/qeth: Don't call dev_close/dev_open (DOWN/UP)
+    - ip6mr: Fix skb_under_panic in ip6mr_cache_report()
+    - vxlan: Fix nexthop hash size
+    - net/mlx5: fs_core: Make find_closest_ft more generic
+    - net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio
+    - prestera: fix fallback to previous version on same major version
+    - tcp_metrics: fix addr_same() helper
+    - tcp_metrics: annotate data-races around tm->tcpm_stamp
+    - tcp_metrics: annotate data-races around tm->tcpm_lock
+    - tcp_metrics: annotate data-races around tm->tcpm_vals[]
+    - tcp_metrics: annotate data-races around tm->tcpm_net
+    - tcp_metrics: fix data-race in tcpm_suck_dst() vs fastopen
+    - scsi: zfcp: Defer fc_rport blocking until after ADISC response
+    - scsi: storvsc: Limit max_sectors for virtual Fibre Channel devices
+    - libceph: fix potential hang in ceph_osdc_notify()
+    - USB: zaurus: Add ID for A-300/B-500/C-700
+    - ceph: defer stopping mdsc delayed_work
+    - firmware: arm_scmi: Drop OF node reference in the transport channel setup
+    - exfat: use kvmalloc_array/kvfree instead of kmalloc_array/kfree
+    - exfat: release s_lock before calling dir_emit()
+    - mtd: spinand: toshiba: Fix ecc_get_status
+    - mtd: rawnand: meson: fix OOB available bytes for ECC
+    - arm64: dts: stratix10: fix incorrect I2C property for SCL signal
+    - wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
+    - rbd: prevent busy loop when requesting exclusive lock
+    - bpf: Disable preemption in bpf_event_output
+    - open: make RESOLVE_CACHED correctly test for O_TMPFILE
+    - drm/ttm: check null pointer before accessing when swapping
+    - bpf, cpumap: Make sure kthread is running before map update returns
+    - file: reinstate f_pos locking optimization for regular files
+    - fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_load_attr_list()
+    - fs/sysv: Null check to prevent null-ptr-deref bug
+    - net: usbnet: Fix WARNING in usbnet_start_xmit/usb_submit_urb
+    - fs: Protect reconfiguration of sb read-write from racing writes
+    - ext2: Drop fragment support
+    - mtd: rawnand: omap_elm: Fix incorrect type in assignment
+    - mtd: rawnand: rockchip: fix oobfree offset and description
+    - mtd: rawnand: rockchip: Align hwecc vs. raw page helper layouts
+    - mtd: rawnand: fsl_upm: Fix an off-by one test in fun_exec_op()
+    - powerpc/mm/altmap: Fix altmap boundary check
+    - drm/imx/ipuv3: Fix front porch adjustment upon hactive aligning
+    - selftests/rseq: check if libc rseq support is registered
+    - selftests/rseq: Play nice with binaries statically linked against glibc
+      2.35+
+    - soundwire: bus: pm_runtime_request_resume on peripheral attachment
+    - soundwire: fix enumeration completion
+    - PM / wakeirq: support enabling wake-up irq after runtime_suspend called
+    - PM: sleep: wakeirq: fix wake irq arming
+    - Linux 5.15.126
+  * Jammy update: v5.15.125 upstream stable release (LP: #2036843)
+    - ia64/cpu: Switch to arch_cpu_finalize_init()
+    - m68k/cpu: Switch to arch_cpu_finalize_init()
+    - mips/cpu: Switch to arch_cpu_finalize_init()
+    - sh/cpu: Switch to arch_cpu_finalize_init()
+    - Linux 5.15.125
+    - Upstream stable to v5.15.125
+  * CVE-2023-42755
+    - net/sched: Retire rsvp classifier
+    - [Config] remove NET_CLS_RSVP and NET_CLS_RSVP6
+  * CVE-2023-42753
+    - netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for
+      ip_set_hash_netportnet.c
+  * CVE-2023-34319
+    - xen/netback: Fix buffer overrun triggered by unusual packet
+  * CVE-2023-5197
+    - netfilter: nf_tables: disallow rule removal from chain binding
+  * CVE-2023-4921
+    - net: sched: sch_qfq: Fix UAF in qfq_dequeue()
+  * CVE-2023-42752
+    - igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
+  * Avoid address overwrite in kernel_connect (LP: #2035163)
+    - net: Avoid address overwrite in kernel_connect
+  * NULL Pointer Dereference During KVM MMU Page Invalidation (LP: #2035166)
+    - KVM: x86/mmu: Track the number of TDP MMU pages, but not the actual pages
+  * Fix suspend hang on Lenovo workstation (LP: #2034479)
+    - igb: Fix igb_down hung on surprise removal
+  * [regression] Unable to initialize SGX enclaves with XFRM other than 3
+    (LP: #2034745)
+    - x86/fpu: Set X86_FEATURE_OSXSAVE feature after enabling OSXSAVE in CR4
+  * CVE-2023-4881
+    - netfilter: nftables: exthdr: fix 4-byte stack OOB write
+  * CVE-2023-4622
+    - af_unix: Fix null-ptr-deref in unix_stream_sendpage().
+  * Jammy update: v5.15.124 upstream stable release (LP: #2035400)
+    - jbd2: Fix wrongly judgement for buffer head removing while doing checkpoint
+    - KVM: s390: pv: fix index value of replaced ASCE
+    - io_uring: don't audit the capability check in io_uring_create()
+    - gpio: tps68470: Make tps68470_gpio_output() always set the initial value
+    - pwm: Add a stub for devm_pwmchip_add()
+    - gpio: mvebu: Make use of devm_pwmchip_add
+    - gpio: mvebu: fix irq domain leak
+    - btrfs: fix race between quota disable and relocation
+    - i2c: Delete error messages for failed memory allocations
+    - i2c: Improve size determinations
+    - i2c: nomadik: Remove unnecessary goto label
+    - i2c: nomadik: Use devm_clk_get_enabled()
+    - i2c: nomadik: Remove a useless call in the remove function
+    - PCI/ASPM: Return 0 or -ETIMEDOUT from pcie_retrain_link()
+    - PCI/ASPM: Factor out pcie_wait_for_retrain()
+    - PCI/ASPM: Avoid link retraining race
+    - PCI: rockchip: Remove writes to unused registers
+    - PCI: rockchip: Fix window mapping and address translation for endpoint
+    - PCI: rockchip: Don't advertise MSI-X in PCIe capabilities
+    - dlm: cleanup plock_op vs plock_xop
+    - dlm: rearrange async condition return
+    - fs: dlm: interrupt posix locks only when process is killed
+    - drm/ttm: Don't print error message if eviction was interrupted
+    - drm/ttm: Don't leak a resource on eviction error
+    - n_tty: Rename tail to old_tail in n_tty_read()
+    - tty: fix hang on tty device with no_room set
+    - drm/ttm: never consider pinned BOs for eviction&swap
+    - cifs: missing directory in MAINTAINERS file
+    - cifs: use fs_context for automounts
+    - ksmbd: remove internal.h include
+    - cifs: if deferred close is disabled then close files immediately
+    - pwm: meson: Simplify duplicated per-channel tracking
+    - pwm: meson: fix handling of period/duty if greater than UINT_MAX
+    - tracing/probes: Add symstr type for dynamic events
+    - tracing/probes: Fix to avoid double count of the string length on the array
+    - tracing: Allow synthetic events to pass around stacktraces
+    - Revert "tracing: Add "(fault)" name injection to kernel probes"
+    - tracing/probes: Fix to record 0-length data_loc in fetch_store_string*() if
+      fails
+    - scsi: qla2xxx: Remove unused declarations for qla2xxx
+    - scsi: qla2xxx: Multi-que support for TMF
+    - scsi: qla2xxx: Fix task management cmd failure
+    - scsi: qla2xxx: Fix task management cmd fail due to unavailable resource
+    - scsi: qla2xxx: Add debug prints in the device remove path
+    - scsi: qla2xxx: Fix hang in task management
+    - drm/amdgpu: fix vkms crtc settings
+    - drm/amdgpu/vkms: relax timer deactivation by hrtimer_try_to_cancel
+    - phy: qcom-snps: Use dev_err_probe() to simplify code
+    - phy: qcom-snps: correct struct qcom_snps_hsphy kerneldoc
+    - phy: qcom-snps-femto-v2: keep cfg_ahb_clk enabled during runtime suspend
+    - phy: qcom-snps-femto-v2: properly enable ref clock
+    - soundwire: qcom: update status correctly with mask
+    - media: staging: atomisp: select V4L2_FWNODE
+    - i40e: Fix an NULL vs IS_ERR() bug for debugfs_create_dir()
+    - iavf: fix potential deadlock on allocation failure
+    - iavf: check for removal state before IAVF_FLAG_PF_COMMS_FAILED
+    - net: phy: marvell10g: fix 88x3310 power up
+    - net: hns3: fix wrong tc bandwidth weight data issue
+    - net: hns3: fix wrong bw weight of disabled tc issue
+    - vxlan: move to its own directory
+    - vxlan: calculate correct header length for GPE
+    - phy: hisilicon: Fix an out of bounds check in hisi_inno_phy_probe()
+    - ethernet: atheros: fix return value check in atl1e_tso_csum()
+    - ipv6 addrconf: fix bug where deleting a mngtmpaddr can create a new
+      temporary address
+    - ice: Fix memory management in ice_ethtool_fdir.c
+    - bonding: reset bond's flags when down link is P2P device
+    - team: reset team's flags when down link is P2P device
+    - net: stmmac: Apply redundant write work around on 4.xx too
+    - platform/x86: msi-laptop: Fix rfkill out-of-sync on MSI Wind U100
+    - igc: Fix Kernel Panic during ndo_tx_timeout callback
+    - netfilter: nft_set_rbtree: fix overlap expiration walk
+    - net/sched: mqprio: refactor nlattr parsing to a separate function
+    - net/sched: mqprio: add extack to mqprio_parse_nlattr()
+    - net/sched: mqprio: Add length check for TCA_MQPRIO_{MAX/MIN}_RATE64
+    - benet: fix return value check in be_lancer_xmit_workarounds()
+    - tipc: check return value of pskb_trim()
+    - tipc: stop tipc crypto on failure in tipc_node_create
+    - RDMA/mlx4: Make check for invalid flags stricter
+    - drm/msm/dpu: drop enum dpu_core_perf_data_bus_id
+    - drm/msm/adreno: Fix snapshot BINDLESS_DATA size
+    - RDMA/irdma: Add missing read barriers
+    - RDMA/irdma: Fix data race on CQP completion stats
+    - RDMA/irdma: Fix data race on CQP request done
+    - RDMA/mthca: Fix crash when polling CQ for shared QPs
+    - RDMA/bnxt_re: Prevent handling any completions after qp destroy
+    - drm/msm: Fix IS_ERR_OR_NULL() vs NULL check in a5xx_submit_in_rb()
+    - ASoC: fsl_spdif: Silence output on stop
+    - block: Fix a source code comment in include/uapi/linux/blkzoned.h
+    - dm raid: fix missing reconfig_mutex unlock in raid_ctr() error paths
+    - dm raid: clean up four equivalent goto tags in raid_ctr()
+    - dm raid: protect md_stop() with 'reconfig_mutex'
+    - drm/amd: Fix an error handling mistake in psp_sw_init()
+    - RDMA/irdma: Report correct WC error
+    - ata: pata_ns87415: mark ns87560_tf_read static
+    - ring-buffer: Fix wrong stat of cpu_buffer->read
+    - tracing: Fix warning in trace_buffered_event_disable()
+    - Revert "usb: gadget: tegra-xudc: Fix error check in
+      tegra_xudc_powerdomain_init()"
+    - usb: gadget: call usb_gadget_check_config() to verify UDC capability
+    - USB: gadget: Fix the memory leak in raw_gadget driver
+    - KVM: Grab a reference to KVM for VM and vCPU stats file descriptors
+    - KVM: VMX: Don't fudge CR0 and CR4 for restricted L2 guest
+    - serial: qcom-geni: drop bogus runtime pm state update
+    - serial: 8250_dw: Preserve original value of DLF register
+    - serial: sifive: Fix sifive_serial_console_setup() section
+    - USB: serial: option: support Quectel EM060K_128
+    - USB: serial: option: add Quectel EC200A module support
+    - USB: serial: simple: add Kaufmann RKS+CAN VCP
+    - USB: serial: simple: sort driver entries
+    - can: gs_usb: gs_can_close(): add missing set of CAN state to
+      CAN_STATE_STOPPED
+    - Revert "usb: dwc3: core: Enable AutoRetry feature in the controller"
+    - usb: dwc3: pci: skip BYT GPIO lookup table for hardwired phy
+    - usb: dwc3: don't reset device side if dwc3 was configured as host-only
+    - usb: ohci-at91: Fix the unhandle interrupt when resume
+    - USB: quirks: add quirk for Focusrite Scarlett
+    - usb: cdns3: fix incorrect calculation of ep_buf_size when more than one
+      config
+    - usb: xhci-mtk: set the dma max_seg_size
+    - Revert "usb: xhci: tegra: Fix error check"
+    - Documentation: security-bugs.rst: update preferences when dealing with the
+      linux-distros group
+    - Documentation: security-bugs.rst: clarify CVE handling
+    - staging: r8712: Fix memory leak in _r8712_init_xmit_priv()
+    - staging: ks7010: potential buffer overflow in ks_wlan_set_encode_ext()
+    - tty: n_gsm: fix UAF in gsm_cleanup_mux
+    - Revert "xhci: add quirk for host controllers that don't update endpoint DCS"
+    - ALSA: hda/relatek: Enable Mute LED on HP 250 G8
+    - hwmon: (k10temp) Enable AMD3255 Proc to show negative temperature
+    - hwmon: (nct7802) Fix for temp6 (PECI1) processed even if PECI1 disabled
+    - btrfs: check if the transaction was aborted at btrfs_wait_for_commit()
+    - btrfs: check for commit error at btrfs_attach_transaction_barrier()
+    - file: always lock position for FMODE_ATOMIC_POS
+    - nfsd: Remove incorrect check in nfsd4_validate_stateid
+    - tpm_tis: Explicitly check for error code
+    - irq-bcm6345-l1: Do not assume a fixed block to cpu mapping
+    - irqchip/gic-v4.1: Properly lock VPEs when doing a directLPI invalidation
+    - locking/rtmutex: Fix task->pi_waiters integrity
+    - KVM: x86: Disallow KVM_SET_SREGS{2} if incoming CR0 is invalid
+    - virtio-net: fix race between set queues and probe
+    - s390/dasd: fix hanging device after quiesce/resume
+    - ASoC: wm8904: Fill the cache for WM8904_ADC_TEST_0 register
+    - ceph: never send metrics if disable_send_metrics is set
+    - dm cache policy smq: ensure IO doesn't prevent cleaner policy progress
+    - rbd: make get_lock_owner_info() return a single locker or NULL
+    - rbd: harden get_lock_owner_info() a bit
+    - rbd: retrieve and check lock owner twice before blocklisting
+    - tracing: Fix trace_event_raw_event_synth() if else statement
+    - ACPI: processor: perflib: Use the "no limit" frequency QoS
+    - ACPI: processor: perflib: Avoid updating frequency QoS unnecessarily
+    - cpufreq: intel_pstate: Drop ACPI _PSS states table patching
+    - selftests: mptcp: sockopt: use 'iptables-legacy' if available
+    - io_uring: treat -EAGAIN for REQ_F_NOWAIT as final for io-wq
+    - ASoC: cs42l51: fix driver to properly autoload with automatic module loading
+    - selftests: mptcp: join: only check for ip6tables if needed
+    - Linux 5.15.124
+  * Jammy update: v5.15.123 upstream stable release (LP: #2034612)
+    - ALSA: hda/realtek - remove 3k pull low procedure
+    - ALSA: hda/realtek: Add quirk for Clevo NS70AU
+    - ALSA: hda/realtek: Enable Mute LED on HP Laptop 15s-eq2xxx
+    - keys: Fix linking a duplicate key to a keyring's assoc_array
+    - perf probe: Add test for regression introduced by switch to
+      die_get_decl_file()
+    - btrfs: fix warning when putting transaction with qgroups enabled after abort
+    - fuse: revalidate: don't invalidate if interrupted
+    - btrfs: zoned: fix memory leak after finding block group with super blocks
+    - fuse: ioctl: translate ENOSYS in outarg
+    - selftests: tc: set timeout to 15 minutes
+    - selftests: tc: add 'ct' action kconfig dep
+    - regmap: Drop initial version of maximum transfer length fixes
+    - regmap: Account for register length in SMBus I/O limits
+    - can: bcm: Fix UAF in bcm_proc_show()
+    - selftests: tc: add ConnTrack procfs kconfig
+    - drm/client: Fix memory leak in drm_client_target_cloned
+    - drm/client: Fix memory leak in drm_client_modeset_probe
+    - drm/amd/display: Disable MPC split by default on special asic
+    - drm/amd/display: Keep PHY active for DP displays on DCN31
+    - ASoC: fsl_sai: Disable bit clock with transmitter
+    - ASoC: codecs: wcd938x: fix missing clsh ctrl error handling
+    - ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix missing mbhc init error handling
+    - ASoC: codecs: wcd934x: fix resource leaks on component remove
+    - ASoC: codecs: wcd938x: fix codec initialisation race
+    - ASoC: codecs: wcd938x: fix soundwire initialisation race
+    - ext4: correct inline offset when handling xattrs in inode body
+    - drm/radeon: Fix integer overflow in radeon_cs_parser_init
+    - ALSA: emu10k1: roll up loops in DSP setup code for Audigy
+    - quota: Properly disable quotas when add_dquot_ref() fails
+    - quota: fix warning in dqgrab()
+    - udf: Fix uninitialized array access for some pathnames
+    - fs: jfs: Fix UBSAN: array-index-out-of-bounds in dbAllocDmapLev
+    - MIPS: dec: prom: Address -Warray-bounds warning
+    - FS: JFS: Fix null-ptr-deref Read in txBegin
+    - FS: JFS: Check for read-only mounted filesystem in txBegin
+    - spi: bcm63xx: fix max prepend length
+    - fbdev: imxfb: warn about invalid left/right margin
+    - perf build: Fix library not found error when using CSLIBS
+    - pinctrl: amd: Use amd_pinconf_set() for all config options
+    - net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()
+    - bridge: Add extack warning when enabling STP in netns.
+    - ethernet: use eth_hw_addr_set() instead of ether_addr_copy()
+    - of: net: add a helper for loading netdev->dev_addr
+    - ethernet: use of_get_ethdev_address()
+    - net: ethernet: mtk_eth_soc: handle probe deferral
+    - net: sched: cls_bpf: Undo tcf_bind_filter in case of an error
+    - iavf: Fix use-after-free in free_netdev
+    - iavf: Fix out-of-bounds when setting channels on remove
+    - security: keys: Modify mismatched function name
+    - octeontx2-pf: Dont allocate BPIDs for LBK interfaces
+    - bpf: Fix subprog idx logic in check_max_stack_depth
+    - igc: Prevent garbled TX queue with XDP ZEROCOPY
+    - tcp: annotate data-races around tcp_rsk(req)->ts_recent
+    - net: ipv4: Use kfree_sensitive instead of kfree
+    - net:ipv6: check return value of pskb_trim()
+    - Revert "tcp: avoid the lookup process failing to get sk in ehash table"
+    - fbdev: au1200fb: Fix missing IRQ check in au1200fb_drv_probe
+    - llc: Don't drop packet from non-root netns.
+    - netfilter: nf_tables: fix spurious set element insertion failure
+    - netfilter: nf_tables: skip bound chain in netns release path
+    - tcp: annotate data-races around tp->tcp_tx_delay
+    - tcp: annotate data-races around tp->keepalive_time
+    - tcp: annotate data-races around tp->keepalive_intvl
+    - tcp: annotate data-races around tp->keepalive_probes
+    - tcp: annotate data-races around icsk->icsk_syn_retries
+    - tcp: annotate data-races around tp->linger2
+    - tcp: annotate data-races around rskq_defer_accept
+    - tcp: annotate data-races around tp->notsent_lowat
+    - tcp: annotate data-races around icsk->icsk_user_timeout
+    - tcp: annotate data-races around fastopenq.max_qlen
+    - net: phy: prevent stale pointer dereference in phy_init()
+    - jbd2: recheck chechpointing non-dirty buffer
+    - tracing/histograms: Return an error if we fail to add histogram to hist_vars
+      list
+    - nixge: fix mac address error handling again
+    - Linux 5.15.123
+  * allow io_uring to be disabled in runtime (LP: #2035116)
+    - io_uring: add a sysctl to disable io_uring system-wide
+  * CVE-2023-31083
+    - Bluetooth: hci_ldisc: check HCI_UART_PROTO_READY flag in HCIUARTGETPROTO
+  * CVE-2023-3772
+    - xfrm: add NULL check in xfrm_update_ae_params
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  [ Ubuntu: 5.15.0-86.96 ]
+
+  * jammy/linux: 5.15.0-86.96 -proposed tracker (LP: #2036575)
+  * 5.15.0-85 live migration regression (LP: #2036675)
+    - Revert "KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES"
+    - Revert "x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0"
+  * Regression for ubuntu_bpf test build on Jammy 5.15.0-85.95 (LP: #2035181)
+    - selftests/bpf: fix static assert compilation issue for test_cls_*.c
+  * `refcount_t: underflow; use-after-free.` on hidon w/ 5.15.0-85-generic
+    (LP: #2034447)
+    - crypto: rsa-pkcs1pad - Use helper to set reqsize
+
+  [ Ubuntu: 5.15.0-85.95 ]
+
+  * jammy/linux: 5.15.0-85.95 -proposed tracker (LP: #2033821)
+  * Please enable Renesas RZ platform serial installer (LP: #2022361)
+    - [Config] enable hihope RZ/G2M serial console
+    - [Config] Mark sh-sci as built-in
+  * Request backport of xen timekeeping performance improvements (LP: #2033122)
+    - x86/xen/time: prefer tsc as clocksource when it is invariant
+  * kdump doesn't work with UEFI secure boot and kernel lockdown enabled on
+    ARM64 (LP: #2033007)
+    - [Config]: Enable CONFIG_KEXEC_IMAGE_VERIFY_SIG
+    - kexec, KEYS: make the code in bzImage64_verify_sig generic
+    - arm64: kexec_file: use more system keyrings to verify kernel image signature
+  * ubuntu_kernel_selftests:net:vrf-xfrm-tests.sh: 8 failed test cases on
+    jammy/fips (LP: #2019880)
+    - selftests: net: vrf-xfrm-tests: change authentication and encryption algos
+  * ubuntu_kernel_selftests:net:tls: 88 failed test cases on jammy/fips
+    (LP: #2019868)
+    - selftests/harness: allow tests to be skipped during setup
+    - selftests: net: tls: check if FIPS mode is enabled
+  * A general-proteciton exception during guest migration to unsupported PKRU
+    machine (LP: 2032164, reverted)
+    - x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0
+    - KVM: x86: Always enable legacy FP/SSE in allowed user XFEATURES
+  * CVE-2023-4569
+    - netfilter: nf_tables: deactivate catchall elements in next generation
+  * CVE-2023-20569
+    - x86/cpu, kvm: Add support for CPUID_80000021_EAX
+    - x86/srso: Add a Speculative RAS Overflow mitigation
+    - x86/srso: Add IBPB_BRTYPE support
+    - x86/srso: Add SRSO_NO support
+    - x86/srso: Add IBPB
+    - x86/srso: Add IBPB on VMEXIT
+    - x86/srso: Fix return thunks in generated code
+    - x86/srso: Tie SBPB bit setting to microcode patch detection
+    - x86: fix backwards merge of GDS/SRSO bit
+    - x86/srso: Fix build breakage with the LLVM linker
+    - x86/cpu: Fix __x86_return_thunk symbol type
+    - x86/cpu: Fix up srso_safe_ret() and __x86_return_thunk()
+    - x86/alternative: Make custom return thunk unconditional
+    - objtool: Add frame-pointer-specific function ignore
+    - x86/ibt: Add ANNOTATE_NOENDBR
+    - x86/cpu: Clean up SRSO return thunk mess
+    - x86/cpu: Rename original retbleed methods
+    - x86/cpu: Rename srso_(.*)_alias to srso_alias_\1
+    - x86/cpu: Cleanup the untrain mess
+    - x86/srso: Explain the untraining sequences a bit more
+    - x86/static_call: Fix __static_call_fixup()
+    - x86/retpoline: Don't clobber RFLAGS during srso_safe_ret()
+    - x86/srso: Disable the mitigation on unaffected configurations
+    - x86/retpoline,kprobes: Fix position of thunk sections with CONFIG_LTO_CLANG
+    - objtool/x86: Fixup frame-pointer vs rethunk
+    - x86/srso: Correct the mitigation status when SMT is disabled
+    - objtool/x86: Fix SRSO mess
+    - Ubuntu: [Config]: enable Speculative Return Stack Overflow mitigation
+  * Fix unreliable ethernet cable detection on I219 NIC (LP: #2028122)
+    - e1000e: Use PME poll to circumvent unreliable ACPI wake
+  * Need to get fine-grained control for FAN(TFN) Participant. (LP: #2031333)
+    - ACPI: fan: Separate file for attributes creation
+    - ACPI: fan: Optimize struct acpi_fan_fif
+    - ACPI: fan: Properly handle fine grain control
+    - ACPI: fan: Add additional attributes for fine grain control
+  * [SRU][Ubuntu 22.04.1] Unable to interpret the frequency values in
+    cpuinfo_min_freq and cpuino_max_freq sysfs files. (LP: #2030924)
+    - cpufreq: intel_pstate: Fix scaling for hybrid-capable
+  * CVE-2023-40283
+    - Bluetooth: L2CAP: Fix use-after-free in l2cap_sock_ready_cb
+  * CVE-2023-20588
+    - x86/bugs: Increase the x86 bugs vector size to two u32s
+    - x86/CPU/AMD: Do not leak quotient data after a division by 0
+    - x86/CPU/AMD: Fix the DIV(0) initial fix attempt
+  * CVE-2023-4194
+    - net: tun_chr_open(): set sk_uid from current_fsuid()
+    - net: tap_open(): set sk_uid from current_fsuid()
+  * CVE-2023-4155
+    - KVM: SEV: Refactor out sev_es_state struct
+    - KVM: SEV: Fall back to vmalloc for SEV-ES scratch area if necessary
+    - KVM: SVM: Do not terminate SEV-ES guests on GHCB validation failure
+    - KVM: SVM: Exit to userspace on ENOMEM/EFAULT GHCB errors
+    - KVM: SEV: snapshot the GHCB before accessing it
+    - KVM: SEV: only access GHCB fields once
+  * CVE-2023-1206
+    - tcp: Reduce chance of collisions in inet6_hashfn().
+  * Crashing with CPU soft lock on GA kernel 5.15.0.79.76 and HWE kernel
+    5.19.0-46.47-22.04.1 (LP: #2032176)
+    - Revert "KVM: x86: enable TDP MMU by default"
+  * Jammy update: v5.15.122 upstream stable release (LP: #2032690)
+    - Linux 5.15.122
+    - Upstream stable to v5.15.122
+  * Jammy update: v5.15.121 upstream stable release (LP: #2032689)
+    - netfilter: nf_tables: drop map element references from preparation phase
+    - fs: pipe: reveal missing function protoypes
+    - x86/resctrl: Only show tasks' pid in current pid namespace
+    - blk-iocost: use spin_lock_irqsave in adjust_inuse_and_calc_cost
+    - md/raid10: check slab-out-of-bounds in md_bitmap_get_counter
+    - md/raid10: fix overflow of md/safe_mode_delay
+    - md/raid10: fix wrong setting of max_corr_read_errors
+    - md/raid10: fix null-ptr-deref of mreplace in raid10_sync_request
+    - md/raid10: fix io loss while replacement replace rdev
+    - irqchip/jcore-aic: Fix missing allocation of IRQ descriptors
+    - svcrdma: Prevent page release when nothing was received
+    - posix-timers: Prevent RT livelock in itimer_delete()
+    - tracing/timer: Add missing hrtimer modes to decode_hrtimer_mode().
+    - clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe
+    - PM: domains: fix integer overflow issues in genpd_parse_state()
+    - perf/arm-cmn: Fix DTC reset
+    - powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
+    - ARM: 9303/1: kprobes: avoid missing-declaration warnings
+    - cpufreq: intel_pstate: Fix energy_performance_preference for passive
+    - thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()
+    - rcutorture: Correct name of use_softirq module parameter
+    - rcuscale: Always log error message
+    - rcuscale: Move shutdown from wait_event() to wait_event_idle()
+    - rcu/rcuscale: Move rcu_scale_*() after kfree_scale_cleanup()
+    - rcu/rcuscale: Stop kfree_scale_thread thread(s) after unloading rcuscale
+    - kselftest: vDSO: Fix accumulation of uninitialized ret when CLOCK_REALTIME
+      is undefined
+    - perf/ibs: Fix interface via core pmu events
+    - x86/mm: Fix __swp_entry_to_pte() for Xen PV guests
+    - locking/atomic: arm: fix sync ops
+    - evm: Complete description of evm_inode_setattr()
+    - evm: Fix build warnings
+    - ima: Fix build warnings
+    - pstore/ram: Add check for kstrdup
+    - igc: Enable and fix RX hash usage by netstack
+    - wifi: ath9k: fix AR9003 mac hardware hang check register offset calculation
+    - wifi: ath9k: avoid referencing uninit memory in ath9k_wmi_ctrl_rx
+    - libbpf: btf_dump_type_data_check_overflow needs to consider
+      BTF_MEMBER_BITFIELD_SIZE
+    - samples/bpf: Fix buffer overflow in tcp_basertt
+    - spi: spi-geni-qcom: Correct CS_TOGGLE bit in SPI_TRANS_CFG
+    - wifi: wilc1000: fix for absent RSN capabilities WFA testcase
+    - wifi: mwifiex: Fix the size of a memory allocation in
+      mwifiex_ret_802_11_scan()
+    - sctp: add bpf_bypass_getsockopt proto callback
+    - libbpf: fix offsetof() and container_of() to work with CO-RE
+    - bpf: Don't EFAULT for {g,s}setsockopt with wrong optlen
+    - spi: dw: Round of n_bytes to power of 2
+    - nfc: llcp: fix possible use of uninitialized variable in
+      nfc_llcp_send_connect()
+    - bpftool: JIT limited misreported as negative value on aarch64
+    - regulator: core: Fix more error checking for debugfs_create_dir()
+    - regulator: core: Streamline debugfs operations
+    - wifi: orinoco: Fix an error handling path in spectrum_cs_probe()
+    - wifi: orinoco: Fix an error handling path in orinoco_cs_probe()
+    - wifi: atmel: Fix an error handling path in atmel_probe()
+    - wl3501_cs: use eth_hw_addr_set()
+    - wifi: wl3501_cs: Fix an error handling path in wl3501_probe()
+    - wifi: ray_cs: Utilize strnlen() in parse_addr()
+    - wifi: ray_cs: Drop useless status variable in parse_addr()
+    - wifi: ray_cs: Fix an error handling path in ray_probe()
+    - wifi: ath9k: don't allow to overwrite ENDPOINT0 attributes
+    - selftests/bpf: Fix check_mtu using wrong variable type
+    - wifi: rsi: Do not configure WoWlan in shutdown hook if not enabled
+    - wifi: rsi: Do not set MMC_PM_KEEP_POWER in shutdown
+    - watchdog/perf: define dummy watchdog_update_hrtimer_threshold() on correct
+      config
+    - watchdog/perf: more properly prevent false positives with turbo modes
+    - kexec: fix a memory leak in crash_shrink_memory()
+    - memstick r592: make memstick_debug_get_tpc_name() static
+    - wifi: ath9k: Fix possible stall on ath9k_txq_list_has_key()
+    - rtnetlink: extend RTEXT_FILTER_SKIP_STATS to IFLA_VF_INFO
+    - wifi: iwlwifi: pull from TXQs with softirqs disabled
+    - iwlwifi: don't dump_stack() when we get an unexpected interrupt
+    - wifi: iwlwifi: pcie: fix NULL pointer dereference in
+      iwl_pcie_irq_rx_msix_handler()
+    - wifi: cfg80211: rewrite merging of inherited elements
+    - wifi: iwlwifi: mvm: indicate HW decrypt for beacon protection
+    - wifi: ath9k: convert msecs to jiffies where needed
+    - bpf: Omit superfluous address family check in __bpf_skc_lookup
+    - bpf: Factor out socket lookup functions for the TC hookpoint.
+    - bpf: Call __bpf_sk_lookup()/__bpf_skc_lookup() directly via TC hookpoint
+    - bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings
+    - can: length: fix bitstuffing count
+    - igc: Fix race condition in PTP tx code
+    - net: stmmac: fix double serdes powerdown
+    - netlink: fix potential deadlock in netlink_set_err()
+    - netlink: do not hard code device address lenth in fdb dumps
+    - bonding: do not assume skb mac_header is set
+    - selftests: rtnetlink: remove netdevsim device after ipsec offload test
+    - gtp: Fix use-after-free in __gtp_encap_destroy().
+    - net: axienet: Move reset before 64-bit DMA detection
+    - sfc: fix crash when reading stats while NIC is resetting
+    - lib/ts_bm: reset initial match offset for every block of text
+    - netfilter: conntrack: dccp: copy entire header to stack buffer, not just
+      basic one
+    - netfilter: nf_conntrack_sip: fix the ct_sip_parse_numerical_param() return
+      value.
+    - ipvlan: Fix return value of ipvlan_queue_xmit()
+    - netlink: Add __sock_i_ino() for __netlink_diag_dump().
+    - drm/amd/display: Add logging for display MALL refresh setting
+    - radeon: avoid double free in ci_dpm_init()
+    - drm/amd/display: Explicitly specify update type per plane info change
+    - Input: drv260x - sleep between polling GO bit
+    - drm/bridge: tc358768: always enable HS video mode
+    - drm/bridge: tc358768: fix PLL parameters computation
+    - drm/bridge: tc358768: fix PLL target frequency
+    - drm/bridge: tc358768: fix TCLK_ZEROCNT computation
+    - drm/bridge: tc358768: Add atomic_get_input_bus_fmts() implementation
+    - drm/bridge: tc358768: fix TCLK_TRAILCNT computation
+    - drm/bridge: tc358768: fix THS_ZEROCNT computation
+    - drm/bridge: tc358768: fix TXTAGOCNT computation
+    - drm/bridge: tc358768: fix THS_TRAILCNT computation
+    - drm/vram-helper: fix function names in vram helper doc
+    - ARM: dts: BCM5301X: Drop "clock-names" from the SPI node
+    - ARM: dts: meson8b: correct uart_B and uart_C clock references
+    - Input: adxl34x - do not hardcode interrupt trigger type
+    - drm: sun4i_tcon: use devm_clk_get_enabled in `sun4i_tcon_init_clocks`
+    - drm/panel: sharp-ls043t1le01: adjust mode settings
+    - ARM: dts: stm32: Move ethernet MAC EEPROM from SoM to carrier boards
+    - bus: ti-sysc: Fix dispc quirk masking bool variables
+    - arm64: dts: microchip: sparx5: do not use PSCI on reference boards
+    - clk: imx: scu: use _safe list iterator to avoid a use after free
+    - RDMA/bnxt_re: Disable/kill tasklet only if it is enabled
+    - RDMA/bnxt_re: Fix to remove unnecessary return labels
+    - RDMA/bnxt_re: Use unique names while registering interrupts
+    - RDMA/bnxt_re: Remove a redundant check inside bnxt_re_update_gid
+    - RDMA/bnxt_re: Fix to remove an unnecessary log
+    - drm/msm/dsi: don't allow enabling 14nm VCO with unprogrammed rate
+    - drm/msm/disp/dpu: get timing engine status from intf status register
+    - drm/msm/dpu: Set DPU_DATA_HCTL_EN for in INTF_SC7180_MASK
+    - ARM: dts: gta04: Move model property out of pinctrl node
+    - arm64: dts: qcom: msm8916: correct camss unit address
+    - arm64: dts: qcom: msm8994: correct SPMI unit address
+    - arm64: dts: qcom: msm8996: correct camss unit address
+    - arm64: dts: qcom: sdm630: correct camss unit address
+    - arm64: dts: qcom: sdm845: correct camss unit address
+    - arm64: dts: qcom: db820c: Move blsp1_uart2 pin states to msm8996.dtsi
+    - arm64: dts: qcom: apq8016-sbc: Update modem and WiFi firmware path
+    - arm64: dts: qcom: apq8016-sbc: Clarify firmware-names
+    - arm64: dts: qcom: apq8016-sbc: fix mpps state names
+    - arm64: dts: qcom: Drop unneeded extra device-specific includes
+    - arm64: dts: qcom: apq8016-sbc: Fix regulator constraints
+    - arm64: dts: qcom: apq8016-sbc: Fix 1.8V power rail on LS expansion
+    - drm/panel: simple: fix active size for Ampire AM-480272H3TMQW-T01H
+    - ARM: ep93xx: fix missing-prototype warnings
+    - ARM: omap2: fix missing tick_broadcast() prototype
+    - arm64: dts: qcom: apq8096: fix fixed regulator name property
+    - arm64: dts: mediatek: mt8183: Add mediatek,broken-save-restore-fw to kukui
+    - ARM: dts: stm32: Shorten the AV96 HDMI sound card name
+    - memory: brcmstb_dpfe: fix testing array offset after use
+    - ASoC: es8316: Increment max value for ALC Capture Target Volume control
+    - ASoC: es8316: Do not set rate constraints for unsupported MCLKs
+    - ARM: dts: meson8: correct uart_B and uart_C clock references
+    - soc/fsl/qe: fix usb.c build errors
+    - RDMA/irdma: avoid fortify-string warning in irdma_clr_wqes
+    - IB/hfi1: Use bitmap_zalloc() when applicable
+    - IB/hfi1: Fix wrong mmu_node used for user SDMA packet after invalidate
+    - RDMA/hns: Fix hns_roce_table_get return value
+    - ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier
+    - arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1
+    - fbdev: omapfb: lcd_mipid: Fix an error handling path in mipid_spi_probe()
+    - arm64: dts: ti: k3-j7200: Fix physical address of pin
+    - ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2
+    - ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx
+    - hwmon: (gsc-hwmon) fix fan pwm temperature scaling
+    - hwmon: (adm1275) Allow setting sample averaging
+    - hwmon: (pmbus/adm1275) Fix problems with temperature monitoring on ADM1272
+    - ARM: dts: BCM5301X: fix duplex-full => full-duplex
+    - drm/amdkfd: Fix potential deallocation of previously deallocated memory.
+    - drm/amd/display: Fix artifacting on eDP panels when engaging freesync video
+      mode
+    - drm/radeon: fix possible division-by-zero errors
+    - amdgpu: validate offset_in_bo of drm_amdgpu_gem_va
+    - drm/msm/a5xx: really check for A510 in a5xx_gpu_init
+    - RDMA/bnxt_re: wraparound mbox producer index
+    - RDMA/bnxt_re: Avoid calling wake_up threads from spin_lock context
+    - clk: imx: clk-imx8mn: fix memory leak in imx8mn_clocks_probe
+    - clk: imx: clk-imx8mp: improve error handling in imx8mp_clocks_probe()
+    - arm64: dts: qcom: sm8250-edo: Panel framebuffer is 2.5k instead of 4k
+    - clk: clocking-wizard: Fix Oops in clk_wzrd_register_divider()
+    - clk: tegra: tegra124-emc: Fix potential memory leak
+    - ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer
+    - drm/msm/dpu: do not enable color-management if DSPPs are not available
+    - drm/msm/dp: Free resources after unregistering them
+    - arm64: dts: mediatek: Add cpufreq nodes for MT8192
+    - arm64: dts: mediatek: mt8192: Fix CPUs capacity-dmips-mhz
+    - drm/msm/dpu: correct MERGE_3D length
+    - clk: vc5: check memory returned by kasprintf()
+    - clk: cdce925: check return value of kasprintf()
+    - clk: si5341: return error if one synth clock registration fails
+    - clk: si5341: check return value of {devm_}kasprintf()
+    - clk: si5341: free unused memory on probe failure
+    - clk: keystone: sci-clk: check return value of kasprintf()
+    - clk: ti: clkctrl: check return value of kasprintf()
+    - drivers: meson: secure-pwrc: always enable DMA domain
+    - ovl: update of dentry revalidate flags after copy up
+    - ASoC: imx-audmix: check return value of devm_kasprintf()
+    - clk: Fix memory leak in devm_clk_notifier_register()
+    - PCI: cadence: Fix Gen2 Link Retraining process
+    - PCI: vmd: Reset VMD config register between soft reboots
+    - scsi: qedf: Fix NULL dereference in error handling
+    - pinctrl: bcm2835: Handle gpiochip_add_pin_range() errors
+    - PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free
+    - scsi: 3w-xxxx: Add error handling for initialization failure in tw_probe()
+    - PCI: pciehp: Cancel bringup sequence if card is not present
+    - PCI: ftpci100: Release the clock resources
+    - PCI: Add pci_clear_master() stub for non-CONFIG_PCI
+    - perf bench: Use unbuffered output when pipe/tee'ing to a file
+    - perf bench: Add missing setlocale() call to allow usage of %'d style
+      formatting
+    - pinctrl: cherryview: Return correct value if pin in push-pull mode
+    - kcsan: Don't expect 64 bits atomic builtins from 32 bits architectures
+    - powerpc/interrupt: Don't read MSR from interrupt_exit_kernel_prepare()
+    - powerpc/signal32: Force inlining of __unsafe_save_user_regs() and
+      save_tm_user_regs_unsafe()
+    - perf script: Fix allocation of evsel->priv related to per-event dump files
+    - perf dwarf-aux: Fix off-by-one in die_get_varname()
+    - powerpc/64s: Fix VAS mm use after free
+    - pinctrl: microchip-sgpio: check return value of devm_kasprintf()
+    - pinctrl: at91-pio4: check return value of devm_kasprintf()
+    - powerpc/powernv/sriov: perform null check on iov before dereferencing iov
+    - powerpc: simplify ppc_save_regs
+    - powerpc: update ppc_save_regs to save current r1 in pt_regs
+    - riscv: uprobes: Restore thread.bad_cause
+    - powerpc/book3s64/mm: Fix DirectMap stats in /proc/meminfo
+    - powerpc/mm/dax: Fix the condition when checking if altmap vmemap can cross-
+      boundary
+    - hwrng: virtio - add an internal buffer
+    - hwrng: virtio - don't wait on cleanup
+    - hwrng: virtio - don't waste entropy
+    - hwrng: virtio - always add a pending request
+    - hwrng: virtio - Fix race on data_avail and actual data
+    - modpost: remove broken calculation of exception_table_entry size
+    - crypto: nx - fix build warnings when DEBUG_FS is not enabled
+    - modpost: fix section mismatch message for R_ARM_ABS32
+    - modpost: fix section mismatch message for R_ARM_{PC24,CALL,JUMP24}
+    - crypto: marvell/cesa - Fix type mismatch warning
+    - modpost: fix off by one in is_executable_section()
+    - ARC: define ASM_NL and __ALIGN(_STR) outside #ifdef __ASSEMBLY__ guard
+    - crypto: qat - honor CRYPTO_TFM_REQ_MAY_SLEEP flag
+    - crypto: qat - replace get_current_node() with numa_node_id()
+    - crypto: qat - use reference to structure in dma_map_single()
+    - crypto: kpp - Add helper to set reqsize
+    - crypto: qat - Use helper to set reqsize
+    - crypto: qat - unmap buffer before free for DH
+    - crypto: qat - unmap buffers before free for RSA
+    - NFSv4.1: freeze the session table upon receiving NFS4ERR_BADSESSION
+    - SMB3: Do not send lease break acknowledgment if all file handles have been
+      closed
+    - dax: Fix dax_mapping_release() use after free
+    - dax: Introduce alloc_dev_dax_id()
+    - dax/kmem: Pass valid argument to memory_group_register_static
+    - hwrng: st - keep clock enabled while hwrng is registered
+    - kbuild: Disable GCOV for *.mod.o
+    - efi/libstub: Disable PCI DMA before grabbing the EFI memory map
+    - ksmbd: avoid field overflow warning
+    - ACPI: utils: Fix acpi_evaluate_dsm_typed() redefinition error
+    - bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
+    - USB: serial: option: add LARA-R6 01B PIDs
+    - usb: dwc3: gadget: Propagate core init errors to UDC during pullup
+    - phy: tegra: xusb: Clear the driver reference in usb-phy dev
+    - iio: adc: ad7192: Fix null ad7192_state pointer access
+    - iio: adc: ad7192: Fix internal/external clock selection
+    - iio: accel: fxls8962af: errata bug only applicable for FXLS8962AF
+    - iio: accel: fxls8962af: fixup buffer scan element type
+    - ALSA: hda/realtek: Add quirk for Clevo NPx0SNx
+    - ALSA: jack: Fix mutex call in snd_jack_report()
+    - block: fix signed int overflow in Amiga partition support
+    - block: add overflow checks for Amiga partition support
+    - block: change all __u32 annotations to __be32 in affs_hardblocks.h
+    - block: increment diskseq on all media change events
+    - SUNRPC: Fix UAF in svc_tcp_listen_data_ready()
+    - w1: w1_therm: fix locking behavior in convert_t
+    - w1: fix loop in w1_fini()
+    - sh: j2: Use ioremap() to translate device tree address into kernel memory
+    - usb: dwc2: platform: Improve error reporting for problems during .remove()
+    - usb: dwc2: Fix some error handling paths
+    - serial: 8250: omap: Fix freeing of resources on failed register
+    - clk: qcom: camcc-sc7180: Add parent dependency to all camera GDSCs
+    - clk: qcom: gcc-ipq6018: Use floor ops for sdcc clocks
+    - media: usb: Check az6007_read() return value
+    - media: videodev2.h: Fix struct v4l2_input tuner index comment
+    - media: usb: siano: Fix warning due to null work_func_t function pointer
+    - media: i2c: Correct format propagation for st-mipid02
+    - clk: qcom: reset: Allow specifying custom reset delay
+    - clk: qcom: reset: support resetting multiple bits
+    - clk: qcom: ipq6018: fix networking resets
+    - usb: dwc3: qcom: Fix potential memory leak
+    - usb: gadget: u_serial: Add null pointer check in gserial_suspend
+    - extcon: Fix kernel doc of property fields to avoid warnings
+    - extcon: Fix kernel doc of property capability fields to avoid warnings
+    - usb: phy: phy-tahvo: fix memory leak in tahvo_usb_probe()
+    - usb: hide unused usbfs_notify_suspend/resume functions
+    - serial: 8250: lock port for stop_rx() in omap8250_irq()
+    - serial: 8250: lock port for UART_IER access in omap8250_irq()
+    - kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
+    - coresight: Fix loss of connection info when a module is unloaded
+    - mfd: rt5033: Drop rt5033-battery sub-device
+    - media: venus: helpers: Fix ALIGN() of non power of two
+    - media: atomisp: gmin_platform: fix out_len in gmin_get_config_dsm_var()
+    - KVM: s390: fix KVM_S390_GET_CMMA_BITS for GFNs in memslot holes
+    - usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()
+    - usb: dwc3: qcom: Fix an error handling path in dwc3_qcom_probe()
+    - usb: common: usb-conn-gpio: Set last role to unknown before initial
+      detection
+    - usb: dwc3-meson-g12a: Fix an error handling path in dwc3_meson_g12a_probe()
+    - mfd: intel-lpss: Add missing check for platform_get_resource
+    - Revert "usb: common: usb-conn-gpio: Set last role to unknown before initial
+      detection"
+    - serial: 8250_omap: Use force_suspend and resume for system suspend
+    - test_firmware: return ENOMEM instead of ENOSPC on failed memory allocation
+    - nvmem: rmem: Use NVMEM_DEVID_AUTO
+    - mfd: stmfx: Fix error path in stmfx_chip_init
+    - mfd: stmfx: Nullify stmfx->vdd in case of error
+    - KVM: s390: vsie: fix the length of APCB bitmap
+    - KVM: s390/diag: fix racy access of physical cpu number in diag 9c handler
+    - mfd: stmpe: Only disable the regulators if they are enabled
+    - phy: tegra: xusb: check return value of devm_kzalloc()
+    - pwm: imx-tpm: force 'real_period' to be zero in suspend
+    - pwm: sysfs: Do not apply state to already disabled PWMs
+    - pwm: ab8500: Fix error code in probe()
+    - pwm: mtk_disp: Fix the disable flow of disp_pwm
+    - md/raid10: fix the condition to call bio_end_io_acct()
+    - rtc: st-lpc: Release some resources in st_rtc_probe() in case of error
+    - drm/i915/psr: Use hw.adjusted mode when calculating io/fast wake times
+    - media: cec: i2c: ch7322: also select REGMAP
+    - sctp: fix potential deadlock on &net->sctp.addr_wq_lock
+    - net/sched: act_ipt: add sanity checks on table name and hook locations
+    - Add MODULE_FIRMWARE() for FIRMWARE_TG357766.
+    - ibmvnic: Do not reset dql stats on NON_FATAL err
+    - net: dsa: vsc73xx: fix MTU configuration
+    - spi: bcm-qspi: return error if neither hif_mspi nor mspi is available
+    - mailbox: ti-msgmgr: Fill non-message tx data fields with 0x0
+    - f2fs: fix error path handling in truncate_dnode()
+    - octeontx2-af: Fix mapping for NIX block from CGX connection
+    - octeontx2-af: Add validation before accessing cgx and lmac
+    - ntfs: Fix panic about slab-out-of-bounds caused by ntfs_listxattr()
+    - powerpc: allow PPC_EARLY_DEBUG_CPM only when SERIAL_CPM=y
+    - net: bridge: keep ports without IFF_UNICAST_FLT in BR_PROMISC mode
+    - tcp: annotate data races in __tcp_oow_rate_limited()
+    - xsk: Honor SO_BINDTODEVICE on bind
+    - net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
+    - riscv: move memblock_allow_resize() after linear mapping is ready
+    - pptp: Fix fib lookup calls.
+    - net: dsa: tag_sja1105: fix MAC DA patching from meta frames
+    - octeontx-af: fix hardware timestamp configuration
+    - s390/qeth: Fix vipa deletion
+    - sh: dma: Fix DMA channel offset calculation
+    - apparmor: fix missing error check for rhashtable_insert_fast
+    - i2c: xiic: Defer xiic_wakeup() and __xiic_start_xfer() in xiic_process()
+    - i2c: xiic: Don't try to handle more interrupt events after error
+    - extcon: usbc-tusb320: Convert to i2c's .probe_new()
+    - btrfs: do not BUG_ON() on tree mod log failure at balance_level()
+    - i2c: qup: Add missing unwind goto in qup_i2c_probe()
+    - NFSD: add encoding of op_recall flag for write delegation
+    - io_uring: wait interruptibly for request completions on exit
+    - mmc: core: disable TRIM on Kingston EMMC04G-M627
+    - mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M
+    - mmc: mmci: Set PROBE_PREFER_ASYNCHRONOUS
+    - mmc: sdhci: fix DMA configure compatibility issue when 64bit DMA mode is
+      used.
+    - bcache: fixup btree_cache_wait list damage
+    - bcache: Remove unnecessary NULL point check in node allocations
+    - bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent
+    - um: Use HOST_DIR for mrproper
+    - integrity: Fix possible multiple allocation in integrity_inode_get()
+    - autofs: use flexible array in ioctl structure
+    - shmem: use ramfs_kill_sb() for kill_sb method of ramfs-based tmpfs
+    - ext4: Remove ext4 locking of moved directory
+    - Revert "f2fs: fix potential corruption when moving a directory"
+    - fs: Establish locking order for unrelated directories
+    - fs: Lock moved directories
+    - ipvs: increase ip_vs_conn_tab_bits range for 64BIT
+    - jffs2: reduce stack usage in jffs2_build_xattr_subsystem()
+    - fs: avoid empty option when generating legacy mount string
+    - btrfs: add handling for RAID1C23/DUP to btrfs_reduce_alloc_profile
+    - btrfs: delete unused BGs while reclaiming BGs
+    - btrfs: bail out reclaim process if filesystem is read-only
+    - btrfs: reinsert BGs failed to reclaim
+    - btrfs: fix race when deleting quota root from the dirty cow roots list
+    - btrfs: fix extent buffer leak after tree mod log failure at split_node()
+    - btrfs: do not BUG_ON() on tree mod log failure at __btrfs_cow_block()
+    - ASoC: mediatek: mt8173: Fix irq error path
+    - ASoC: mediatek: mt8173: Fix snd_soc_component_initialize error path
+    - ARM: dts: qcom: ipq4019: fix broken NAND controller properties override
+    - ARM: orion5x: fix d2net gpio initialization
+    - leds: trigger: netdev: Recheck NETDEV_LED_MODE_LINKUP on dev rename
+    - fs: no need to check source
+    - ovl: fix null pointer dereference in ovl_get_acl_rcu()
+    - fanotify: disallow mount/sb marks on kernel internal pseudo fs
+    - netfilter: conntrack: Avoid nf_ct_helper_hash uses after free
+    - wireguard: queueing: use saner cpu selection wrapping
+    - wireguard: netlink: send staged packets when setting initial private key
+    - tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
+    - block/partition: fix signedness issue for Amiga partitions
+    - io_uring: Use io_schedule* in cqring wait
+    - io_uring: add reschedule point to handle_tw_list()
+    - net: lan743x: Don't sleep in atomic context
+    - workqueue: clean up WORK_* constant types, clarify masking
+    - ksmbd: use ksmbd_req_buf_next() in ksmbd_smb2_check_message()
+    - ksmbd: validate command payload size
+    - ksmbd: fix out-of-bound read in smb2_write
+    - ksmbd: validate session id and tree id in the compound request
+    - drm/panel: simple: Add connector_type for innolux_at043tn24
+    - drm/bridge: ti-sn65dsi86: Fix auxiliary bus lifetime
+    - drm/panel: simple: Add Powertip PH800480T013 drm_display_mode flags
+    - igc: Remove delay during TX ring configuration
+    - net/mlx5e: fix double free in mlx5e_destroy_flow_table
+    - net/mlx5e: fix memory leak in mlx5e_ptp_open
+    - net/mlx5e: Check for NOT_READY flag state after locking
+    - igc: set TP bit in 'supported' and 'advertising' fields of
+      ethtool_link_ksettings
+    - igc: Handle PPS start time programming for past time values
+    - scsi: qla2xxx: Fix error code in qla2x00_start_sp()
+    - bpf: Fix max stack depth check for async callbacks
+    - net: mvneta: fix txq_map in case of txq_number==1
+    - gve: Set default duplex configuration to full
+    - ionic: remove WARN_ON to prevent panic_on_warn
+    - net: bgmac: postpone turning IRQs off to avoid SoC hangs
+    - net: prevent skb corruption on frag list segmentation
+    - icmp6: Fix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev().
+    - udp6: fix udp6_ehashfn() typo
+    - ntb: idt: Fix error handling in idt_pci_driver_init()
+    - NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
+    - ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
+    - NTB: ntb_transport: fix possible memory leak while device_register() fails
+    - NTB: ntb_tool: Add check for devm_kcalloc
+    - ipv6/addrconf: fix a potential refcount underflow for idev
+    - platform/x86: wmi: remove unnecessary argument
+    - platform/x86: wmi: use guid_t and guid_equal()
+    - platform/x86: wmi: move variables
+    - platform/x86: wmi: Break possible infinite loop when parsing GUID
+    - kernel/trace: Fix cleanup logic of enable_trace_eprobe
+    - igc: Fix launchtime before start of cycle
+    - igc: Fix inserting of empty frame for launchtime
+    - bpf, riscv: Support riscv jit to provide bpf_line_info
+    - riscv, bpf: Fix inconsistent JIT image generation
+    - drm/i915: Fix one wrong caching mode enum usage
+    - octeontx2-pf: Add additional check for MCAM rules
+    - erofs: avoid infinite loop in z_erofs_do_read_page() when reading beyond EOF
+    - erofs: decouple basic mount options from fs_context
+    - erofs: fix fsdax unavailability for chunk-based regular files
+    - wifi: airo: avoid uninitialized warning in airo_get_rate()
+    - bpf: cpumap: Fix memory leak in cpu_map_update_elem
+    - net/sched: flower: Ensure both minimum and maximum ports are specified
+    - riscv: mm: fix truncation warning on RV32
+    - netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()
+    - net/sched: make psched_mtu() RTNL-less safe
+    - nvme-pci: remove nvme_queue from nvme_iod
+    - nvme-pci: fix DMA direction of unmapping integrity data
+    - pinctrl: amd: Fix mistake in handling clearing pins at startup
+    - pinctrl: amd: Detect internal GPIO0 debounce handling
+    - pinctrl: amd: Detect and mask spurious interrupts
+    - pinctrl: amd: Only use special debounce behavior for GPIO 0
+    - tpm: tpm_vtpm_proxy: fix a race condition in /dev/vtpmx creation
+    - mtd: rawnand: meson: fix unaligned DMA buffers handling
+    - net: bcmgenet: Ensure MDIO unregistration has clocks enabled
+    - mm/damon/ops-common: atomically test and clear young on ptes and pmds
+    - powerpc: Fail build if using recordmcount with binutils v2.37
+    - misc: fastrpc: Create fastrpc scalar with correct buffer count
+    - powerpc/security: Fix Speculation_Store_Bypass reporting on Power10
+    - arm64: errata: Add detection for TRBE overwrite in FILL mode
+    - erofs: fix compact 4B support for 16k block size
+    - MIPS: Loongson: Fix cpu_probe_loongson() again
+    - MIPS: KVM: Fix NULL pointer dereference
+    - ext4: Fix reusing stale buffer heads from last failed mounting
+    - ext4: fix wrong unit use in ext4_mb_clear_bb
+    - ext4: get block from bh in ext4_free_blocks for fast commit replay
+    - ext4: fix wrong unit use in ext4_mb_new_blocks
+    - ext4: fix to check return value of freeze_bdev() in ext4_shutdown()
+    - ext4: turn quotas off if mount failed after enabling quotas
+    - ext4: only update i_reserved_data_blocks on successful block allocation
+    - jfs: jfs_dmap: Validate db_l2nbperpage while mounting
+    - hwrng: imx-rngc - fix the timeout for init and self check
+    - dm integrity: reduce vmalloc space footprint on 32-bit architectures
+    - PCI/PM: Avoid putting EloPOS E2/S2/H2 PCIe Ports in D3cold
+    - PCI: Add function 1 DMA alias quirk for Marvell 88SE9235
+    - PCI: qcom: Disable write access to read only registers for IP v2.3.3
+    - PCI: rockchip: Assert PCI Configuration Enable bit after probe
+    - PCI: rockchip: Write PCI Device ID to correct register
+    - PCI: rockchip: Add poll and timeout to wait for PHY PLLs to be locked
+    - PCI: rockchip: Fix legacy IRQ generation for RK3399 PCIe endpoint core
+    - PCI: rockchip: Use u32 variable to access 32-bit registers
+    - PCI: rockchip: Set address alignment for endpoint mode
+    - misc: pci_endpoint_test: Free IRQs before removing the device
+    - misc: pci_endpoint_test: Re-init completion for every test
+    - mfd: pm8008: Fix module autoloading
+    - md/raid0: add discard support for the 'original' layout
+    - dm init: add dm-mod.waitfor to wait for asynchronously probed block devices
+    - fs: dlm: return positive pid value for F_GETLK
+    - drm/atomic: Allow vblank-enabled + self-refresh "disable"
+    - drm/rockchip: vop: Leave vblank enabled in self-refresh
+    - drm/amdgpu: fix clearing mappings for BOs that are always valid in VM
+    - drm/amd/display: Correct `DMUB_FW_VERSION` macro
+    - drm/amdgpu: avoid restore process run into dead loop.
+    - drm/ttm: Don't leak a resource on swapout move error
+    - serial: atmel: don't enable IRQs prematurely
+    - tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in
+      case of error
+    - tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when
+      iterating clk
+    - tty: serial: imx: fix rs485 rx after tx
+    - firmware: stratix10-svc: Fix a potential resource leak in
+      svc_create_memory_pool()
+    - libceph: harden msgr2.1 frame segment length checks
+    - ceph: don't let check_caps skip sending responses for revoke msgs
+    - xhci: Fix resume issue of some ZHAOXIN hosts
+    - xhci: Fix TRB prefetch issue of ZHAOXIN hosts
+    - xhci: Show ZHAOXIN xHCI root hub speed correctly
+    - meson saradc: fix clock divider mask length
+    - opp: Fix use-after-free in lazy_opp_tables after probe deferral
+    - soundwire: qcom: fix storing port config out-of-bounds
+    - Revert "8250: add support for ASIX devices with a FIFO bug"
+    - bus: ixp4xx: fix IXP4XX_EXP_T1_MASK
+    - s390/decompressor: fix misaligned symbol build error
+    - tracing/histograms: Add histograms to hist_vars if they have referenced
+      variables
+    - tracing: Fix memory leak of iter->temp when reading trace_pipe
+    - samples: ftrace: Save required argument registers in sample trampolines
+    - net: ena: fix shift-out-of-bounds in exponential backoff
+    - ring-buffer: Fix deadloop issue on reading trace_pipe
+    - ftrace: Fix possible warning on checking all pages used in
+      ftrace_process_locs()
+    - xtensa: ISS: fix call to split_if_spec
+    - tracing: Fix null pointer dereference in tracing_err_log_open()
+    - selftests: mptcp: sockopt: return error if wrong mark
+    - selftests: mptcp: depend on SYN_COOKIES
+    - tracing/probes: Fix not to count error code to total length
+    - tracing/probes: Fix to update dynamic data counter if fetcharg uses it
+    - scsi: qla2xxx: Wait for io return on terminate rport
+    - scsi: qla2xxx: Array index may go out of bound
+    - scsi: qla2xxx: Avoid fcport pointer dereference
+    - scsi: qla2xxx: Fix buffer overrun
+    - scsi: qla2xxx: Fix potential NULL pointer dereference
+    - scsi: qla2xxx: Check valid rport returned by fc_bsg_to_rport()
+    - scsi: qla2xxx: Correct the index of array
+    - scsi: qla2xxx: Pointer may be dereferenced
+    - scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue
+    - MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
+    - net/sched: sch_qfq: reintroduce lmax bound check for MTU
+    - drm/atomic: Fix potential use-after-free in nonblocking commits
+    - Linux 5.15.121
+  * Jammy update: v5.15.120 upstream stable release (LP: #2032688)
+    - mptcp: fix possible divide by zero in recvmsg()
+    - mptcp: consolidate fallback and non fallback state machine
+    - mm, hwpoison: try to recover from copy-on write faults
+    - mm, hwpoison: when copy-on-write hits poison, take page offline
+    - drm/amdgpu: Set vmbo destroy after pt bo is created
+    - x86/microcode/AMD: Load late on both threads too
+    - x86/smp: Use dedicated cache-line for mwait_play_dead()
+    - can: isotp: isotp_sendmsg(): fix return error fix on TX path
+    - bpf: ensure main program has an extable
+    - HID: wacom: Use ktime_t rather than int when dealing with timestamps
+    - HID: logitech-hidpp: add HIDPP_QUIRK_DELAYED_INIT for the T651.
+    - Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak
+      in mtk_thermal_probe"
+    - perf symbols: Symbol lookup with kcore can fail if multiple segments match
+      stext
+    - scripts/tags.sh: Resolve gtags empty index generation
+    - drm/amdgpu: Validate VM ioctl flags.
+    - parisc: Delete redundant register definitions in <asm/assembly.h>
+    - nubus: Partially revert proc_create_single_data() conversion
+    - Linux 5.15.120
+  * Jammy update: v5.15.119 upstream stable release (LP: #2032683)
+    - drm/amd/display: fix the system hang while disable PSR
+    - tracing: Add tracing_reset_all_online_cpus_unlocked() function
+    - tpm, tpm_tis: Claim locality in interrupt handler
+    - drm/amd/display: Add minimal pipe split transition state
+    - drm/amd/display: Use dc_update_planes_and_stream
+    - drm/amd/display: Add wrapper to call planes and stream update
+    - tick/common: Align tick period during sched_timer setup
+    - selftests: mptcp: lib: skip if missing symbol
+    - selftests: mptcp: lib: skip if not below kernel version
+    - selftests/mount_setattr: fix redefine struct mount_attr build error
+    - selftests: mptcp: pm nl: remove hardcoded default limits
+    - selftests: mptcp: join: use 'iptables-legacy' if available
+    - selftests: mptcp: join: skip check if MIB counter not supported
+    - nilfs2: fix buffer corruption due to concurrent device reads
+    - ACPI: sleep: Avoid breaking S3 wakeup due to might_sleep()
+    - KVM: Avoid illegal stage2 mapping on invalid memory slot
+    - Drivers: hv: vmbus: Call hv_synic_free() if hv_synic_alloc() fails
+    - Drivers: hv: vmbus: Fix vmbus_wait_for_unload() to scan present CPUs
+    - PCI: hv: Fix a race condition bug in hv_pci_query_relations()
+    - Revert "PCI: hv: Fix a timing issue which causes kdump to fail occasionally"
+    - PCI: hv: Remove the useless hv_pcichild_state from struct hv_pci_dev
+    - PCI: hv: Fix a race condition in hv_irq_unmask() that can cause panic
+    - PCI: hv: Add a per-bus mutex state_lock
+    - cgroup: Do not corrupt task iteration when rebinding subsystem
+    - mmc: sdhci-msm: Disable broken 64-bit DMA on MSM8916
+    - mmc: meson-gx: remove redundant mmc_request_done() call from irq context
+    - mmc: mmci: stm32: fix max busy timeout calculation
+    - ip_tunnels: allow VXLAN/GENEVE to inherit TOS/TTL from VLAN
+    - regulator: pca9450: Fix LDO3OUT and LDO4OUT MASK
+    - regmap: spi-avmm: Fix regmap_bus max_raw_write
+    - writeback: fix dereferencing NULL mapping->host on writeback_page_template
+    - io_uring/net: save msghdr->msg_control for retries
+    - io_uring/net: clear msg_controllen on partial sendmsg retry
+    - io_uring/net: disable partial retries for recvmsg with cmsg
+    - nilfs2: prevent general protection fault in nilfs_clear_dirty_page()
+    - x86/mm: Avoid using set_pgd() outside of real PGD pages
+    - memfd: check for non-NULL file_seals in memfd_create() syscall
+    - mmc: meson-gx: fix deferred probing
+    - ieee802154: hwsim: Fix possible memory leaks
+    - xfrm: Treat already-verified secpath entries as optional
+    - xfrm: interface: rename xfrm_interface.c to xfrm_interface_core.c
+    - xfrm: Ensure policies always checked on XFRM-I input path
+    - bpf: track immediate values written to stack by BPF_ST instruction
+    - bpf: Fix verifier id tracking of scalars on spill
+    - xfrm: fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
+    - selftests: net: fcnal-test: check if FIPS mode is enabled
+    - xfrm: Linearize the skb after offloading if needed.
+    - net: qca_spi: Avoid high load if QCA7000 is not available
+    - mmc: mtk-sd: fix deferred probing
+    - mmc: mvsdio: fix deferred probing
+    - mmc: omap: fix deferred probing
+    - mmc: omap_hsmmc: fix deferred probing
+    - mmc: owl: fix deferred probing
+    - mmc: sdhci-acpi: fix deferred probing
+    - mmc: sh_mmcif: fix deferred probing
+    - mmc: usdhi60rol0: fix deferred probing
+    - ipvs: align inner_mac_header for encapsulation
+    - net: dsa: mt7530: fix trapping frames on non-MT7621 SoC MT7530 switch
+    - net: dsa: mt7530: fix handling of BPDUs on MT7530 switch
+    - be2net: Extend xmit workaround to BE3 chip
+    - netfilter: nft_set_pipapo: .walk does not deal with generations
+    - netfilter: nf_tables: disallow element updates of bound anonymous sets
+    - netfilter: nf_tables: reject unbound anonymous set before commit phase
+    - netfilter: nf_tables: reject unbound chain set before commit phase
+    - netfilter: nf_tables: disallow updates of anonymous sets
+    - netfilter: nfnetlink_osf: fix module autoload
+    - Revert "net: phy: dp83867: perform soft reset and retain established link"
+    - bpf/btf: Accept function names that contain dots
+    - selftests: forwarding: Fix race condition in mirror installation
+    - sch_netem: acquire qdisc lock in netem_change()
+    - gpio: Allow per-parent interrupt data
+    - gpiolib: Fix GPIO chip IRQ initialization restriction
+    - gpio: sifive: add missing check for platform_get_irq
+    - scsi: target: iscsi: Prevent login threads from racing between each other
+    - HID: wacom: Add error check to wacom_parse_and_register()
+    - arm64: Add missing Set/Way CMO encodings
+    - media: cec: core: don't set last_initiator if tx in progress
+    - nfcsim.c: Fix error checking for debugfs_create_dir
+    - usb: gadget: udc: fix NULL dereference in remove()
+    - nvme: double KA polling frequency to avoid KATO with TBKAS on
+    - Input: soc_button_array - add invalid acpi_index DMI quirk handling
+    - s390/cio: unregister device when the only path is gone
+    - spi: lpspi: disable lpspi module irq in DMA mode
+    - ASoC: simple-card: Add missing of_node_put() in case of error
+    - soundwire: dmi-quirks: add new mapping for HP Spectre x360
+    - ASoC: nau8824: Add quirk to active-high jack-detect
+    - s390/purgatory: disable branch profiling
+    - ARM: dts: Fix erroneous ADS touchscreen polarities
+    - drm/exynos: vidi: fix a wrong error return
+    - drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl
+    - drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl
+    - vhost_net: revert upend_idx only on retriable error
+    - x86/apic: Fix kernel panic when booting with intremap=off and x2apic_phys
+    - i2c: imx-lpi2c: fix type char overflow issue when calculating the clock
+      cycle
+    - act_mirred: remove unneded merge conflict markers
+    - Linux 5.15.119
+  * Jammy update: v5.15.118 upstream stable release (LP: #2030239)
+    - test_firmware: Use kstrtobool() instead of strtobool()
+    - test_firmware: prevent race conditions by a correct implementation of
+      locking
+    - test_firmware: fix a memory leak with reqs buffer
+    - ksmbd: fix slab-out-of-bounds read in smb2_handle_negotiate
+    - drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram
+    - of: overlay: rename variables to be consistent
+    - of: overlay: rework overlay apply and remove kfree()s
+    - of: overlay: Fix missing of_node_put() in error case of
+      init_overlay_changeset()
+    - power: supply: ab8500: Fix external_power_changed race
+    - power: supply: sc27xx: Fix external_power_changed race
+    - power: supply: bq27xxx: Use mod_delayed_work() instead of cancel() +
+      schedule()
+    - ARM: dts: vexpress: add missing cache properties
+    - tools: gpio: fix debounce_period_us output of lsgpio
+    - power: supply: Ratelimit no data debug output
+    - platform/x86: asus-wmi: Ignore WMI events with codes 0x7B, 0xC0
+    - regulator: Fix error checking for debugfs_create_dir
+    - irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issues
+    - power: supply: Fix logic checking if system is running from battery
+    - btrfs: scrub: try harder to mark RAID56 block groups read-only
+    - btrfs: handle memory allocation failure in btrfs_csum_one_bio
+    - ASoC: soc-pcm: test if a BE can be prepared
+    - parisc: Improve cache flushing for PCXL in arch_sync_dma_for_cpu()
+    - parisc: Flush gatt writes and adjust gatt mask in parisc_agp_mask_memory()
+    - MIPS: unhide PATA_PLATFORM
+    - MIPS: Alchemy: fix dbdma2
+    - mips: Move initrd_start check after initrd address sanitisation.
+    - ASoC: dwc: move DMA init to snd_soc_dai_driver probe()
+    - xen/blkfront: Only check REQ_FUA for writes
+    - drm:amd:amdgpu: Fix missing buffer object unlock in failure path
+    - NVMe: Add MAXIO 1602 to bogus nid list.
+    - irqchip/gic: Correctly validate OF quirk descriptors
+    - wifi: cfg80211: fix locking in regulatory disconnect
+    - wifi: cfg80211: fix double lock bug in reg_wdev_chan_valid()
+    - epoll: ep_autoremove_wake_function should use list_del_init_careful
+    - ocfs2: fix use-after-free when unmounting read-only filesystem
+    - ocfs2: check new file size on fallocate call
+    - nios2: dts: Fix tse_mac "max-frame-size" property
+    - nilfs2: fix incomplete buffer cleanup in nilfs_btnode_abort_change_key()
+    - nilfs2: fix possible out-of-bounds segment allocation in resize ioctl
+    - kexec: support purgatories with .text.hot sections
+    - x86/purgatory: remove PGO flags
+    - powerpc/purgatory: remove PGO flags
+    - ALSA: usb-audio: Add quirk flag for HEM devices to enable native DSD
+      playback
+    - dm thin metadata: check fail_io before using data_sm
+    - nouveau: fix client work fence deletion race
+    - RDMA/uverbs: Restrict usage of privileged QKEYs
+    - net: usb: qmi_wwan: add support for Compal RXM-G1
+    - drm/amdgpu: add missing radeon secondary PCI ID
+    - ALSA: hda/realtek: Add a quirk for Compaq N14JP6
+    - Remove DECnet support from kernel
+    - [Config] updateconfigs for DECNET
+    - thunderbolt: dma_test: Use correct value for absent rings when creating
+      paths
+    - thunderbolt: Mask ring interrupt on Intel hardware as well
+    - USB: serial: option: add Quectel EM061KGL series
+    - serial: lantiq: add missing interrupt ack
+    - usb: dwc3: gadget: Reset num TRBs before giving back the request
+    - RDMA/rtrs: Fix the last iu->buf leak in err path
+    - RDMA/rtrs: Fix rxe_dealloc_pd warning
+    - RDMA/rxe: Fix packet length checks
+    - spi: fsl-dspi: avoid SCK glitches with continuous transfers
+    - netfilter: nf_tables: integrate pipapo into commit protocol
+    - netfilter: nfnetlink: skip error delivery on batch in case of ENOMEM
+    - net: enetc: correct the indexes of highest and 2nd highest TCs
+    - ping6: Fix send to link-local addresses with VRF.
+    - net/sched: simplify tcf_pedit_act
+    - net/sched: act_pedit: remove extra check for key type
+    - net/sched: act_pedit: Parse L3 Header for L4 offset
+    - RDMA/rxe: Remove the unused variable obj
+    - RDMA/rxe: Removed unused name from rxe_task struct
+    - RDMA/rxe: Fix the use-before-initialization error of resp_pkts
+    - iavf: remove mask from iavf_irq_enable_queues()
+    - octeontx2-af: fixed resource availability check
+    - octeontx2-af: fix lbk link credits on cn10k
+    - RDMA/mlx5: Initiate dropless RQ for RAW Ethernet functions
+    - RDMA/cma: Always set static rate to 0 for RoCE
+    - IB/uverbs: Fix to consider event queue closing also upon non-blocking mode
+    - IB/isert: Fix dead lock in ib_isert
+    - IB/isert: Fix possible list corruption in CMA handler
+    - IB/isert: Fix incorrect release of isert connection
+    - net: ethtool: correct MAX attribute value for stats
+    - ipvlan: fix bound dev checking for IPv6 l3s mode
+    - sctp: fix an error code in sctp_sf_eat_auth()
+    - igc: Clean the TX buffer and TX descriptor ring
+    - igb: fix nvm.ops.read() error handling
+    - drm/nouveau: don't detect DSM for non-NVIDIA device
+    - drm/nouveau/dp: check for NULL nv_connector->native_mode
+    - drm/nouveau: add nv_encoder pointer check for NULL
+    - cifs: fix lease break oops in xfstest generic/098
+    - ext4: drop the call to ext4_error() from ext4_get_group_info()
+    - net/sched: cls_api: Fix lockup on flushing explicitly created chain
+    - net: lapbether: only support ethernet devices
+    - dm: don't lock fs when the map is NULL during suspend or resume
+    - net: tipc: resize nlattr array to correct size
+    - selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
+    - afs: Fix vlserver probe RTT handling
+    - cgroup: always put cset in cgroup_css_set_put_fork
+    - rcu/kvfree: Avoid freeing new kfree_rcu() memory after old grace period
+    - neighbour: Remove unused inline function neigh_key_eq16()
+    - net: Remove unused inline function dst_hold_and_use()
+    - net: Remove DECnet leftovers from flow.h.
+    - neighbour: delete neigh_lookup_nodev as not used
+    - of: overlay: add entry to of_overlay_action_name[]
+    - mmc: block: ensure error propagation for non-blk
+    - nilfs2: reject devices with insufficient block count
+    - Linux 5.15.118
+  * Jammy update: v5.15.117 upstream stable release (LP: #2030107)
+    - ata: ahci: fix enum constants for gcc-13
+    - gcc-plugins: Reorganize gimple includes for GCC 13
+    - remove the sx8 block driver
+    - [Config] updateconfigs for BLK_DEV_SX8
+    - sfc (gcc13): synchronize ef100_enqueue_skb()'s return type
+    - i40e: Remove string printing for i40e_status
+    - i40e: use int for i40e_status
+    - i40e: fix build warning in ice_fltr_add_mac_to_list()
+    - bonding (gcc13): synchronize bond_{a,t}lb_xmit() types
+    - f2fs: fix iostat lock protection
+    - blk-iocost: avoid 64-bit division in ioc_timer_fn
+    - platform/surface: aggregator: Allow completion work-items to be executed in
+      parallel
+    - spi: qup: Request DMA before enabling clocks
+    - afs: Fix setting of mtime when creating a file/dir/symlink
+    - wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll
+    - neighbour: fix unaligned access to pneigh_entry
+    - net: dsa: lan9303: allow vid != 0 in port_fdb_{add|del} methods
+    - bpf: Fix UAF in task local storage
+    - net/ipv6: fix bool/int mismatch for skip_notify_on_dev_down
+    - net/smc: Avoid to access invalid RMBs' MRs in SMCRv1 ADD LINK CONT
+    - net: enetc: correct the statistics of rx bytes
+    - net/sched: fq_pie: ensure reasonable TCA_FQ_PIE_QUANTUM values
+    - drm/i915: Explain the magic numbers for AUX SYNC/precharge length
+    - drm/i915: Use 18 fast wake AUX sync len
+    - Bluetooth: Fix l2cap_disconnect_req deadlock
+    - Bluetooth: L2CAP: Add missing checks for invalid DCID
+    - qed/qede: Fix scheduling while atomic
+    - wifi: cfg80211: fix locking in sched scan stop work
+    - selftests/bpf: Verify optval=NULL case
+    - selftests/bpf: Fix sockopt_sk selftest
+    - netfilter: conntrack: fix NULL pointer dereference in nf_confirm_cthelper
+    - netfilter: ipset: Add schedule point in call_ad().
+    - ipv6: rpl: Fix Route of Death.
+    - rfs: annotate lockless accesses to sk->sk_rxhash
+    - rfs: annotate lockless accesses to RFS sock flow table
+    - drm/i915/selftests: Increase timeout for live_parallel_switch
+    - drm/i915/selftests: Stop using kthread_stop()
+    - drm/i915/selftests: Add some missing error propagation
+    - net: sched: move rtm_tca_policy declaration to include file
+    - net: sched: act_police: fix sparse errors in tcf_police_dump()
+    - net: sched: fix possible refcount leak in tc_chain_tmplt_add()
+    - bpf: Add extra path pointer check to d_path helper
+    - lib: cpu_rmap: Fix potential use-after-free in irq_cpu_rmap_release()
+    - bnxt_en: Don't issue AP reset during ethtool's reset operation
+    - bnxt_en: Query default VLAN before VNIC setup on a VF
+    - bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks
+    - batman-adv: Broken sync while rescheduling delayed work
+    - Input: xpad - delete a Razer DeathAdder mouse VID/PID entry
+    - Input: psmouse - fix OOB access in Elantech protocol
+    - Input: fix open count when closing inhibited device
+    - ALSA: hda/realtek: Add quirk for Clevo NS50AU
+    - ALSA: hda/realtek: Add a quirk for HP Slim Desktop S01
+    - drm/i915/gt: Use the correct error value when kernel_context() fails
+    - drm/amd/pm: conditionally disable pcie lane switching for some
+      sienna_cichlid SKUs
+    - drm/amdgpu: fix xclk freq on CHIP_STONEY
+    - drm/amd/pm: Fix power context allocation in SMU13
+    - can: j1939: j1939_sk_send_loop_abort(): improved error queue handling in
+      J1939 Socket
+    - can: j1939: change j1939_netdev_lock type to mutex
+    - can: j1939: avoid possible use-after-free when j1939_can_rx_register fails
+    - ceph: fix use-after-free bug for inodes when flushing capsnaps
+    - s390/dasd: Use correct lock while counting channel queue length
+    - Bluetooth: Fix use-after-free in hci_remove_ltk/hci_remove_irk
+    - Bluetooth: hci_qca: fix debugfs registration
+    - tee: amdtee: Add return_origin to 'struct tee_cmd_load_ta'
+    - rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting
+    - rbd: get snapshot context after exclusive lock is ensured to be held
+    - pinctrl: meson-axg: add missing GPIOA_18 gpio group
+    - usb: usbfs: Enforce page requirements for mmap
+    - usb: usbfs: Use consistent mmap functions
+    - ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
+    - ASoC: codecs: wsa881x: do not set can_multi_write flag
+    - arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite
+      boards
+    - arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
+    - arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
+    - ASoC: mediatek: mt8195-afe-pcm: Convert to platform remove callback
+      returning void
+    - ASoC: mediatek: mt8195: fix use-after-free in driver remove path
+    - arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
+    - i2c: mv64xxx: Fix reading invalid status value in atomic mode
+    - firmware: arm_ffa: Set handle field to zero in memory descriptor
+    - i2c: sprd: Delete i2c adapter in .remove's error path
+    - eeprom: at24: also select REGMAP
+    - riscv: fix kprobe __user string arg print fault issue
+    - vduse: avoid empty string for dev name
+    - vhost: support PACKED when setting-getting vring_base
+    - vhost_vdpa: support PACKED when setting-getting vring_base
+    - ext4: only check dquot_initialize_needed() when debugging
+    - Linux 5.15.117
+  * CVE-2023-4273
+    - exfat: check if filename entries exceeds max filename length
+  * CVE-2023-4128
+    - net/sched: cls_u32: No longer copy tcf_result on update to avoid use-after-
+      free
+    - net/sched: cls_fw: No longer copy tcf_result on update to avoid use-after-
+      free
+    - net/sched: cls_route: No longer copy tcf_result on update to avoid use-
+      after-free
+  * CVE-2023-3863
+    - nfc: llcp: simplify llcp_sock_connect() error paths
+    - net: nfc: Fix use-after-free caused by nfc_llcp_find_local
+
+  [ Ubuntu: 5.15.0-83.92 ]
+
+  * jammy/linux: 5.15.0-83.92 -proposed tracker (LP: #2031132)
+  * libgnutls report "trap invalid opcode" when trying to install packages over
+    https (LP: #2031093)
+    - [Config]: disable CONFIG_GDS_FORCE_MITIGATION
+
+  [ Ubuntu: 5.15.0-81.90 ]
+
+  * jammy/linux: 5.15.0-81.90 -proposed tracker (LP: #2030422)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] resync getabis
+    - debian/dkms-versions -- update from kernel-versions (main/2023.08.07)
+  * CVE-2022-40982
+    - x86/mm: Initialize text poking earlier
+    - x86/mm: fix poking_init() for Xen PV guests
+    - x86/mm: Use mm_alloc() in poking_init()
+    - mm: Move mm_cachep initialization to mm_init()
+    - init: Provide arch_cpu_finalize_init()
+    - x86/cpu: Switch to arch_cpu_finalize_init()
+    - ARM: cpu: Switch to arch_cpu_finalize_init()
+    - sparc/cpu: Switch to arch_cpu_finalize_init()
+    - um/cpu: Switch to arch_cpu_finalize_init()
+    - init: Remove check_bugs() leftovers
+    - init: Invoke arch_cpu_finalize_init() earlier
+    - init, x86: Move mem_encrypt_init() into arch_cpu_finalize_init()
+    - x86/init: Initialize signal frame size late
+    - x86/fpu: Remove cpuinfo argument from init functions
+    - x86/fpu: Mark init functions __init
+    - x86/fpu: Move FPU initialization into arch_cpu_finalize_init()
+    - x86/xen: Fix secondary processors' FPU initialization
+    - x86/speculation: Add Gather Data Sampling mitigation
+    - x86/speculation: Add force option to GDS mitigation
+    - x86/speculation: Add Kconfig option for GDS
+    - KVM: Add GDS_NO support to KVM
+    - Documentation/x86: Fix backwards on/off logic about YMM support
+    - [Config]: Enable CONFIG_ARCH_HAS_CPU_FINALIZE_INIT and
+      CONFIG_GDS_FORCE_MITIGATION
+  * CVE-2023-3609
+    - net/sched: cls_u32: Fix reference counter leak leading to overflow
+  * CVE-2023-21400
+    - io_uring: ensure IOPOLL locks around deferred work
+  * CVE-2023-4015
+    - netfilter: nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound
+      set/chain
+    - netfilter: nf_tables: unbind non-anonymous set if rule construction fails
+    - netfilter: nf_tables: skip immediate deactivate in _PREPARE_ERROR
+  * CVE-2023-3995
+    - netfilter: nf_tables: disallow rule addition to bound chain via
+      NFTA_RULE_CHAIN_ID
+  * CVE-2023-3777
+    - netfilter: nf_tables: skip bound chain on rule flush
+  * losetup with mknod fails on jammy with kernel 5.15.0-69-generic
+    (LP: #2015400)
+    - loop: do not enforce max_loop hard limit by (new) default
+  * Include the MAC address pass through function on RTL8153DD-CG (LP: #2020295)
+    - r8152: add USB device driver for config selection
+  * Jammy update: v5.15.116 upstream stable release (LP: #2029401)
+    - RDMA/bnxt_re: Fix the page_size used during the MR creation
+    - RDMA/efa: Fix unsupported page sizes in device
+    - RDMA/hns: Fix base address table allocation
+    - RDMA/hns: Modify the value of long message loopback slice
+    - dmaengine: at_xdmac: Move the free desc to the tail of the desc list
+    - dmaengine: at_xdmac: fix potential Oops in at_xdmac_prep_interleaved()
+    - RDMA/bnxt_re: Fix a possible memory leak
+    - RDMA/bnxt_re: Fix return value of bnxt_re_process_raw_qp_pkt_rx
+    - iommu/rockchip: Fix unwind goto issue
+    - iommu/amd: Don't block updates to GATag if guest mode is on
+    - dmaengine: pl330: rename _start to prevent build error
+    - riscv: Fix unused variable warning when BUILTIN_DTB is set
+    - net/mlx5: fw_tracer, Fix event handling
+    - net/mlx5e: Don't attach netdev profile while handling internal error
+    - net: mellanox: mlxbf_gige: Fix skb_panic splat under memory pressure
+    - netrom: fix info-leak in nr_write_internal()
+    - af_packet: Fix data-races of pkt_sk(sk)->num.
+    - amd-xgbe: fix the false linkup in xgbe_phy_status
+    - mtd: rawnand: ingenic: fix empty stub helper definitions
+    - RDMA/irdma: Add SW mechanism to generate completions on error
+    - RDMA/irdma: Prevent QP use after free
+    - RDMA/irdma: Fix Local Invalidate fencing
+    - af_packet: do not use READ_ONCE() in packet_bind()
+    - tcp: deny tcp_disconnect() when threads are waiting
+    - tcp: Return user_mss for TCP_MAXSEG in CLOSE/LISTEN state if user_mss set
+    - net/sched: sch_ingress: Only create under TC_H_INGRESS
+    - net/sched: sch_clsact: Only create under TC_H_CLSACT
+    - net/sched: Reserve TC_H_INGRESS (TC_H_CLSACT) for ingress (clsact) Qdiscs
+    - net/sched: Prohibit regrafting ingress or clsact Qdiscs
+    - net: sched: fix NULL pointer dereference in mq_attach
+    - net/netlink: fix NETLINK_LIST_MEMBERSHIPS length report
+    - udp6: Fix race condition in udp6_sendmsg & connect
+    - net/mlx5e: Fix error handling in mlx5e_refresh_tirs
+    - net/mlx5: Read embedded cpu after init bit cleared
+    - net: dsa: mv88e6xxx: Increase wait after reset deactivation
+    - mtd: rawnand: marvell: ensure timing values are written
+    - mtd: rawnand: marvell: don't set the NAND frequency select
+    - rtnetlink: call validate_linkmsg in rtnl_create_link
+    - drm/amdgpu: release gpu full access after "amdgpu_device_ip_late_init"
+    - watchdog: menz069_wdt: fix watchdog initialisation
+    - ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
+    - drm/amdgpu: Use the default reset when loading or reloading the driver
+    - mailbox: mailbox-test: Fix potential double-free in
+      mbox_test_message_write()
+    - drm/ast: Fix ARM compatibility
+    - btrfs: abort transaction when sibling keys check fails for leaves
+    - ARM: 9295/1: unwind:fix unwind abort for uleb128 case
+    - media: rcar-vin: Select correct interrupt mode for V4L2_FIELD_ALTERNATE
+    - platform/x86: intel_scu_pcidrv: Add back PCI ID for Medfield
+    - gfs2: Don't deref jdesc in evict
+    - fbdev: imsttfb: Fix use after free bug in imsttfb_probe
+    - fbdev: modedb: Add 1920x1080 at 60 Hz video mode
+    - fbdev: stifb: Fix info entry in sti_struct on error path
+    - nbd: Fix debugfs_create_dir error checking
+    - block/rnbd: replace REQ_OP_FLUSH with REQ_OP_WRITE
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for HS-SSD-FUTURE 2048G
+    - nvme-pci: add quirk for missing secondary temperature thresholds
+    - ASoC: dwc: limit the number of overrun messages
+    - um: harddog: fix modular build
+    - xfrm: Check if_id in inbound policy/secpath match
+    - ASoC: dt-bindings: Adjust #sound-dai-cells on TI's single-DAI codecs
+    - ASoC: ssm2602: Add workaround for playback distortions
+    - media: dvb_demux: fix a bug for the continuity counter
+    - media: dvb-usb: az6027: fix three null-ptr-deref in az6027_i2c_xfer()
+    - media: dvb-usb-v2: ec168: fix null-ptr-deref in ec168_i2c_xfer()
+    - media: dvb-usb-v2: ce6230: fix null-ptr-deref in ce6230_i2c_master_xfer()
+    - media: dvb-usb-v2: rtl28xxu: fix null-ptr-deref in rtl28xxu_i2c_xfer
+    - media: dvb-usb: digitv: fix null-ptr-deref in digitv_i2c_xfer()
+    - media: dvb-usb: dw2102: fix uninit-value in su3000_read_mac_address
+    - media: netup_unidvb: fix irq init by register it at the end of probe
+    - media: dvb_ca_en50221: fix a size write bug
+    - media: ttusb-dec: fix memory leak in ttusb_dec_exit_dvb()
+    - media: mn88443x: fix !CONFIG_OF error by drop of_match_ptr from ID table
+    - media: dvb-core: Fix use-after-free due on race condition at dvb_net
+    - media: dvb-core: Fix use-after-free due to race at dvb_register_device()
+    - media: dvb-core: Fix use-after-free due to race condition at dvb_ca_en50221
+    - s390/pkey: zeroize key blobs
+    - s390/topology: honour nr_cpu_ids when adding CPUs
+    - ACPI: resource: Add IRQ override quirk for LG UltraPC 17U70P
+    - wifi: rtl8xxxu: fix authentication timeout due to incorrect RCR value
+    - ARM: dts: stm32: add pin map for CAN controller on stm32f7
+    - arm64/mm: mark private VM_FAULT_X defines as vm_fault_t
+    - arm64: vdso: Pass (void *) to virt_to_page()
+    - wifi: mac80211: simplify chanctx allocation
+    - scsi: core: Decrease scsi_device's iorequest_cnt if dispatch failed
+    - wifi: b43: fix incorrect __packed annotation
+    - netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with
+      CONFIG_NF_NAT
+    - nvme-multipath: don't call blk_mark_disk_dead in nvme_mpath_remove_disk
+    - ALSA: oss: avoid missing-prototype warnings
+    - drm/msm: Be more shouty if per-process pgtables aren't working
+    - atm: hide unused procfs functions
+    - drm/amdgpu: skip disabling fence driver src_irqs when device is unplugged
+    - nvme-pci: Add quirk for Teamgroup MP33 SSD
+    - mailbox: mailbox-test: fix a locking issue in mbox_test_message_write()
+    - media: uvcvideo: Don't expose unsupported formats to userspace
+    - iio: accel: st_accel: Fix invalid mount_matrix on devices without ACPI _ONT
+      method
+    - iio: adc: mxs-lradc: fix the order of two cleanup operations
+    - HID: google: add jewel USB id
+    - HID: wacom: avoid integer overflow in wacom_intuos_inout()
+    - iio: imu: inv_icm42600: fix timestamp reset
+    - dt-bindings: iio: adc: renesas,rcar-gyroadc: Fix adi,ad7476 compatible value
+    - iio: light: vcnl4035: fixed chip ID check
+    - iio: adc: ad_sigma_delta: Fix IRQ issue by setting IRQ_DISABLE_UNLAZY flag
+    - iio: dac: mcp4725: Fix i2c_master_send() return value handling
+    - iio: adc: ad7192: Change "shorted" channels to differential
+    - iio: dac: build ad5758 driver when AD5758 is selected
+    - net: usb: qmi_wwan: Set DTR quirk for BroadMobi BM818
+    - dt-bindings: usb: snps,dwc3: Fix "snps,hsphy_interface" type
+    - usb: gadget: f_fs: Add unbind event before functionfs_unbind
+    - md/raid5: fix miscalculation of 'end_sector' in raid5_read_one_chunk()
+    - misc: fastrpc: return -EPIPE to invocations on device removal
+    - misc: fastrpc: reject new invocations during device removal
+    - scsi: stex: Fix gcc 13 warnings
+    - ata: libata-scsi: Use correct device no in ata_find_dev()
+    - drm/amd/pm: reverse mclk and fclk clocks levels for vangogh
+    - drm/amd/pm: reverse mclk and fclk clocks levels for yellow carp
+    - drm/amd/pm: reverse mclk and fclk clocks levels for renoir
+    - x86/boot: Wrap literal addresses in absolute_pointer()
+    - ath6kl: Use struct_group() to avoid size-mismatched casting
+    - block/blk-iocost (gcc13): keep large values in a new enum
+    - mmc: vub300: fix invalid response handling
+    - mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order
+    - tty: serial: fsl_lpuart: use UARTCTRL_TXINV to send break instead of
+      UARTCTRL_SBK
+    - btrfs: fix csum_tree_block page iteration to avoid tripping on
+      -Werror=array-bounds
+    - powerpc/iommu: Limit number of TCEs to 512 for H_STUFF_TCE hcall
+    - iommu/amd: Fix domain flush size when syncing iotlb
+    - usb: cdns3: allocate TX FIFO size according to composite EP number
+    - usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM
+    - block: fix revalidate performance regression
+    - selinux: don't use make's grouped targets feature yet
+    - tracing/probe: trace_probe_primary_from_call(): checked list_first_entry
+    - selftests: mptcp: connect: skip if MPTCP is not supported
+    - selftests: mptcp: pm nl: skip if MPTCP is not supported
+    - selftests: mptcp: sockopt: skip if MPTCP is not supported
+    - ext4: add EA_INODE checking to ext4_iget()
+    - ext4: set lockdep subclass for the ea_inode in ext4_xattr_inode_cache_find()
+    - ext4: disallow ea_inodes with extended attributes
+    - ext4: add lockdep annotations for i_data_sem for ea_inode's
+    - fbcon: Fix null-ptr-deref in soft_cursor
+    - serial: 8250_tegra: Fix an error handling path in tegra_uart_probe()
+    - test_firmware: fix the memory leak of the allocated firmware buffer
+    - KVM: x86: Account fastpath-only VM-Exits in vCPU stats
+    - ksmbd: fix credit count leakage
+    - ksmbd: fix incorrect AllocationSize set in smb2_get_info
+    - KEYS: asymmetric: Copy sig and digest in public_key_verify_signature()
+    - regmap: Account for register length when chunking
+    - tpm, tpm_tis: Request threaded interrupt handler
+    - drm/rcar: stop using 'imply' for dependencies
+    - [Config] updateconfigs for DRM_RCAR_LVDS
+    - scsi: dpt_i2o: Remove broken pass-through ioctl (I2OUSERCMD)
+    - scsi: dpt_i2o: Do not process completions with invalid addresses
+    - [Config] updateconfigs for SCSI_DPT_I2O
+    - drm/amdgpu/gfx10: Disable gfxoff before disabling powergating.
+    - selftests: mptcp: diag: skip if MPTCP is not supported
+    - selftests: mptcp: simult flows: skip if MPTCP is not supported
+    - selftests: mptcp: join: skip if MPTCP is not supported
+    - ext4: enable the lazy init thread when remounting read/write
+    - ARM: defconfig: drop CONFIG_DRM_RCAR_LVDS
+    - RDMA/irdma: Fix drain SQ hang with no completion
+    - RDMA/irdma: Do not generate SW completions for NOPs
+    - Linux 5.15.116
+  * CVE-2023-20593
+    - x86/cpu/amd: Move the errata checking functionality up
+    - x86/cpu/amd: Add a Zenbleed fix
+  * CVE-2023-4004
+    - netfilter: nft_set_pipapo: fix improper element removal
+  * CVE-2023-3611
+    - net/sched: sch_qfq: refactor parsing of netlink parameters
+    - net/sched: sch_qfq: account for stab overhead in qfq_enqueue
+  * CVE-2023-3610
+    - netfilter: nf_tables: fix chain binding transaction logic
+  * CVE-2023-2898
+    - f2fs: fix to avoid NULL pointer dereference f2fs_write_end_io()
+  * Backport support to tolerate ZSTD compressed firmware files (LP: #2028550)
+    - firmware_loader: EXTRA_FIRMWARE does not support compressed files
+    - firmware: Add the support for ZSTD-compressed firmware files
+    - [Config] Enable FW_LOADER_COMPRESS_ZSTD by default
+  * stacked overlay file system mounts that have chroot() called against them
+    appear to be getting locked (by the kernel most likely?) (LP: #2016398)
+    - SAUCE: overlayfs: fix reference count mismatch
+  * kdump fails on big arm64 systems when offset is not specified (LP: #2024479)
+    - arm64: mm: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
+    - arm64: kdump: Reimplement crashkernel=X
+    - docs: kdump: Update the crashkernel description for arm64
+    - arm64: kdump: Do not allocate crash low memory if not needed
+    - arm64/mm: Define defer_reserve_crashkernel()
+    - arm64: kdump: Provide default size when crashkernel=Y, low is not specified
+    - arm64: kdump: Support crashkernel=X fall back to reserve region above DMA
+      zones
+  * usbrtl sometimes doesn't reload firmware (LP: #2026028)
+    - Bluetooth: btrtl: Ask ic_info to drop firmware
+  * cifs: fix mid leak during reconnection after timeout threshold
+    (LP: #2029138)
+    - cifs: fix mid leak during reconnection after timeout threshold
+  * Jammy update: v5.15.115 upstream stable release (LP: #2028799)
+    - power: supply: bq27xxx: expose battery data when CI=1
+    - power: supply: bq27xxx: Move bq27xxx_battery_update() down
+    - power: supply: bq27xxx: Ensure power_supply_changed() is called on current
+      sign changes
+    - power: supply: bq27xxx: After charger plug in/out wait 0.5s for things to
+      stabilize
+    - power: supply: core: Refactor
+      power_supply_set_input_current_limit_from_supplier()
+    - power: supply: bq24190: Call power_supply_changed() after updating input
+      current
+    - bpf: fix a memory leak in the LRU and LRU_PERCPU hash maps
+    - net/mlx5: devcom only supports 2 ports
+    - net/mlx5e: Fix deadlock in tc route query code
+    - net/mlx5: Devcom, serialize devcom registration
+    - platform/x86: ISST: PUNIT device mapping with Sub-NUMA clustering
+    - platform/x86: ISST: Remove 8 socket limit
+    - net: phy: mscc: enable VSC8501/2 RGMII RX clock
+    - net: dsa: introduce helpers for iterating through ports using dp
+    - net: dsa: mt7530: rework mt753[01]_setup
+    - net: dsa: mt7530: split-off common parts from mt7531_setup
+    - net: dsa: mt7530: fix network connectivity with multiple CPU ports
+    - Bonding: add arp_missed_max option
+    - bonding: fix send_peer_notif overflow
+    - binder: fix UAF caused by faulty buffer cleanup
+    - irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()
+    - irqchip/mips-gic: Use raw spinlock for gic_lock
+    - net/mlx5e: Fix SQ wake logic in ptp napi_poll context
+    - xdp: Allow registering memory model without rxq reference
+    - net: page_pool: use in_softirq() instead
+    - page_pool: fix inconsistency for page_pool_ring_[un]lock()
+    - irqchip/mips-gic: Don't touch vl_map if a local interrupt is not routable
+    - xdp: xdp_mem_allocator can be NULL in trace_mem_connect().
+    - bluetooth: Add cmd validity checks at the start of hci_sock_ioctl()
+    - Revert "binder_alloc: add missing mmap_lock calls when using the VMA"
+    - Revert "android: binder: stop saving a pointer to the VMA"
+    - binder: add lockless binder_alloc_(set|get)_vma()
+    - binder: fix UAF of alloc->vma in race with munmap()
+    - ipv{4,6}/raw: fix output xfrm lookup wrt protocol
+    - netfilter: ctnetlink: Support offloaded conntrack entry deletion
+    - Linux 5.15.115
+  * Jammy update: v5.15.114 upstream stable release (LP: #2028701)
+    - usb: gadget: Properly configure the device for remote wakeup
+    - usb: dwc3: fix gadget mode suspend interrupt handler issue
+    - dt-bindings: ata: ahci-ceva: convert to yaml
+    - dt-bindings: ata: ahci-ceva: Cover all 4 iommus entries
+    - watchdog: sp5100_tco: Immediately trigger upon starting.
+    - ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
+    - spi: fsl-spi: Re-organise transfer bits_per_word adaptation
+    - spi: fsl-cpm: Use 16 bit mode for large transfers with even size
+    - ocfs2: Switch to security_inode_init_security()
+    - arm64: Also reset KASAN tag if page is not PG_mte_tagged
+    - ALSA: hda/ca0132: add quirk for EVGA X299 DARK
+    - ALSA: hda: Fix unhandled register update during auto-suspend period
+    - ALSA: hda/realtek: Enable headset onLenovo M70/M90
+    - mmc: sdhci-esdhc-imx: make "no-mmc-hs400" works
+    - ASoC: rt5682: Disable jack detection interrupt during suspend
+    - net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize
+    - m68k: Move signal frame following exception on 68020/030
+    - parisc: Handle kgdb breakpoints only in kernel context
+    - parisc: Allow to reboot machine after system halt
+    - gpio: mockup: Fix mode of debugfs files
+    - btrfs: use nofs when cleaning up aborted transactions
+    - dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size type
+    - selftests/memfd: Fix unknown type name build failure
+    - parisc: Fix flush_dcache_page() for usage from irq context
+    - perf/x86/uncore: Correct the number of CHAs on SPR
+    - x86/topology: Fix erroneous smp_num_siblings on Intel Hybrid platforms
+    - debugobjects: Don't wake up kswapd from fill_pool()
+    - fbdev: udlfb: Fix endpoint check
+    - net: fix stack overflow when LRO is disabled for virtual interfaces
+    - udplite: Fix NULL pointer dereference in __sk_mem_raise_allocated().
+    - USB: core: Add routines for endpoint checks in old drivers
+    - USB: sisusbvga: Add endpoint checks
+    - media: radio-shark: Add endpoint checks
+    - ASoC: lpass: Fix for KASAN use_after_free out of bounds
+    - net: fix skb leak in __skb_tstamp_tx()
+    - selftests: fib_tests: mute cleanup error message
+    - octeontx2-pf: Fix TSOv6 offload
+    - bpf: Fix mask generation for 32-bit narrow loads of 64-bit fields
+    - ipv6: Fix out-of-bounds access in ipv6_find_tlv()
+    - cifs: mapchars mount option ignored
+    - power: supply: leds: Fix blink to LED on transition
+    - power: supply: mt6360: add a check of devm_work_autocancel in
+      mt6360_charger_probe
+    - power: supply: bq27xxx: Fix bq27xxx_battery_update() race condition
+    - power: supply: bq27xxx: Fix I2C IRQ race on remove
+    - power: supply: bq27xxx: Fix poll_interval handling and races on remove
+    - power: supply: bq27xxx: Add cache parameter to
+      bq27xxx_battery_current_and_status()
+    - power: supply: sbs-charger: Fix INHIBITED bit for Status reg
+    - firmware: arm_ffa: Check if ffa_driver remove is present before executing
+    - firmware: arm_ffa: Fix FFA device names for logical partitions
+    - fs: fix undefined behavior in bit shift for SB_NOUSER
+    - regulator: pca9450: Fix BUCK2 enable_mask
+    - coresight: Fix signedness bug in tmc_etr_buf_insert_barrier_packet()
+    - xen/pvcalls-back: fix double frees with pvcalls_new_active_socket()
+    - x86/show_trace_log_lvl: Ensure stack pointer is aligned, again
+    - ASoC: Intel: Skylake: Fix declaration of enum skl_ch_cfg
+    - sctp: fix an issue that plpmtu can never go to complete state
+    - forcedeth: Fix an error handling path in nv_probe()
+    - platform/mellanox: mlxbf-pmc: fix sscanf() error checking
+    - net/mlx5e: do as little as possible in napi poll when budget is 0
+    - net/mlx5: DR, Fix crc32 calculation to work on big-endian (BE) CPUs
+    - net/mlx5: DR, Check force-loopback RC QP capability independently from RoCE
+    - net/mlx5: Fix error message when failing to allocate device memory
+    - net/mlx5: Devcom, fix error flow in mlx5_devcom_register_device
+    - arm64: dts: imx8mn-var-som: fix PHY detection bug by adding deassert delay
+    - firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors
+    - regulator: mt6359: add read check for PMIC MT6359
+    - 3c589_cs: Fix an error handling path in tc589_probe()
+    - net: phy: mscc: add VSC8502 to MODULE_DEVICE_TABLE
+    - Linux 5.15.114
+  * Jammy update: v5.15.113 upstream stable release (LP: #2028408)
+    - drm/mipi-dsi: Set the fwnode for mipi_dsi_device
+    - ARM: 9296/1: HP Jornada 7XX: fix kernel-doc warnings
+    - net: mdio: mvusb: Fix an error handling path in mvusb_mdio_probe()
+    - scsi: ufs: core: Fix I/O hang that occurs when BKOPS fails in W-LUN suspend
+    - tick/broadcast: Make broadcast device replacement work correctly
+    - linux/dim: Do nothing if no time delta between samples
+    - net: stmmac: switch to use interrupt for hw crosstimestamping
+    - net: stmmac: Initialize MAC_ONEUS_TIC_COUNTER register
+    - net: Fix load-tearing on sk->sk_stamp in sock_recv_cmsgs().
+    - netfilter: nf_tables: always release netdev hooks from notifier
+    - netfilter: conntrack: fix possible bug_on with enable_hooks=1
+    - netlink: annotate accesses to nlk->cb_running
+    - net: annotate sk->sk_err write from do_recvmmsg()
+    - net: deal with most data-races in sk_wait_event()
+    - net: add vlan_get_protocol_and_depth() helper
+    - tcp: add annotations around sk->sk_shutdown accesses
+    - gve: Remove the code of clearing PBA bit
+    - net: datagram: fix data-races in datagram_poll()
+    - af_unix: Fix a data race of sk->sk_receive_queue->qlen.
+    - af_unix: Fix data races around sk->sk_shutdown.
+    - drm/i915/dp: prevent potential div-by-zero
+    - fbdev: arcfb: Fix error handling in arcfb_probe()
+    - ext4: remove an unused variable warning with CONFIG_QUOTA=n
+    - ext4: reflect error codes from ext4_multi_mount_protect() to its callers
+    - ext4: fix lockdep warning when enabling MMP
+    - ext4: allow to find by goal if EXT4_MB_HINT_GOAL_ONLY is set
+    - ext4: allow ext4_get_group_info() to fail
+    - refscale: Move shutdown from wait_event() to wait_event_idle()
+    - rcu: Protect rcu_print_task_exp_stall() ->exp_tasks access
+    - fs: hfsplus: remove WARN_ON() from hfsplus_cat_{read,write}_inode()
+    - drm/displayid: add displayid_get_header() and check bounds better
+    - drm/amd/display: Use DC_LOG_DC in the trasform pixel function
+    - regmap: cache: Return error in cache sync operations for REGCACHE_NONE
+    - arm64: dts: qcom: msm8996: Add missing DWC3 quirks
+    - media: cx23885: Fix a null-ptr-deref bug in buffer_prepare() and
+      buffer_finish()
+    - media: pci: tw68: Fix null-ptr-deref bug in buf prepare and finish
+    - firmware: arm_sdei: Fix sleep from invalid context BUG
+    - ACPI: EC: Fix oops when removing custom query handlers
+    - remoteproc: stm32_rproc: Add mutex protection for workqueue
+    - drm/tegra: Avoid potential 32-bit integer overflow
+    - drm/msm/dp: Clean up handling of DP AUX interrupts
+    - ACPICA: Avoid undefined behavior: applying zero offset to null pointer
+    - ACPICA: ACPICA: check null return of ACPI_ALLOCATE_ZEROED in
+      acpi_db_display_objects
+    - drm/amd: Fix an out of bounds error in BIOS parser
+    - media: Prefer designated initializers over memset for subdev pad ops
+    - wifi: ath: Silence memcpy run-time false positive warning
+    - bpf: Annotate data races in bpf_local_storage
+    - wifi: brcmfmac: cfg80211: Pass the PMK in binary instead of hex
+    - ext2: Check block size validity during mount
+    - scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow
+    - bnxt: avoid overflow in bnxt_get_nvram_directory()
+    - net: pasemi: Fix return type of pasemi_mac_start_tx()
+    - net: Catch invalid index in XPS mapping
+    - scsi: target: iscsit: Free cmds before session free
+    - lib: cpu_rmap: Avoid use after free on rmap->obj array entries
+    - scsi: message: mptlan: Fix use after free bug in mptlan_remove() due to race
+      condition
+    - gfs2: Fix inode height consistency check
+    - scsi: ufs: ufs-pci: Add support for Intel Lunar Lake
+    - ext4: set goal start correctly in ext4_mb_normalize_request
+    - ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()
+    - f2fs: fix to drop all dirty pages during umount() if cp_error is set
+    - f2fs: fix to check readonly condition correctly
+    - samples/bpf: Fix fout leak in hbm's run_bpf_prog
+    - bpf: Add preempt_count_{sub,add} into btf id deny list
+    - wifi: iwlwifi: pcie: fix possible NULL pointer dereference
+    - wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf
+    - null_blk: Always check queue mode setting from configfs
+    - wifi: iwlwifi: dvm: Fix memcpy: detected field-spanning write backtrace
+    - wifi: ath11k: Fix SKB corruption in REO destination ring
+    - nbd: fix incomplete validation of ioctl arg
+    - ipvs: Update width of source for ip_vs_sync_conn_options
+    - Bluetooth: btintel: Add LE States quirk support
+    - Bluetooth: hci_bcm: Fall back to getting bdaddr from EFI if not set
+    - Bluetooth: L2CAP: fix "bad unlock balance" in l2cap_disconnect_rsp
+    - HID: logitech-hidpp: Don't use the USB serial for USB devices
+    - HID: logitech-hidpp: Reconcile USB and Unifying serials
+    - spi: spi-imx: fix MX51_ECSPI_* macros when cs > 3
+    - HID: wacom: generic: Set battery quirk only when we see battery data
+    - usb: typec: tcpm: fix multiple times discover svids error
+    - serial: 8250: Reinit port->pm on port specific driver unbind
+    - mcb-pci: Reallocate memory region to avoid memory overlapping
+    - sched: Fix KCSAN noinstr violation
+    - recordmcount: Fix memory leaks in the uwrite function
+    - RDMA/core: Fix multiple -Warray-bounds warnings
+    - iommu/arm-smmu-qcom: Limit the SMR groups to 128
+    - fs/ntfs3: Fix NULL pointer dereference in 'ni_write_inode'
+    - fs/ntfs3: Enhance the attribute size check
+    - fs/ntfs3: Fix NULL dereference in ni_write_inode
+    - fs/ntfs3: Validate MFT flags before replaying logs
+    - fs/ntfs3: Add length check in indx_get_root
+    - fs/ntfs3: Fix a possible null-pointer dereference in ni_clear()
+    - clk: tegra20: fix gcc-7 constant overflow warning
+    - iommu/arm-smmu-v3: Acknowledge pri/event queue overflow if any
+    - iommu/sprd: Release dma buffer to avoid memory leak
+    - Input: xpad - add constants for GIP interface numbers
+    - phy: st: miphy28lp: use _poll_timeout functions for waits
+    - soundwire: qcom: gracefully handle too many ports in DT
+    - mfd: dln2: Fix memory leak in dln2_probe()
+    - parisc: Replace regular spinlock with spin_trylock on panic path
+    - platform/x86: hp-wmi: Support touchpad on/off
+    - [Config] updateconfigs for X86_PLATFORM_DRIVERS_HP
+    - platform/x86: Move existing HP drivers to a new hp subdir
+    - platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct
+    - xfrm: don't check the default policy if the policy allows the packet
+    - Revert "Fix XFRM-I support for nested ESP tunnels"
+    - drm/msm/dp: unregister audio driver during unbind
+    - drm/msm/dpu: Add INTF_5 interrupts
+    - drm/msm/dpu: Move non-MDP_TOP INTF_INTR offsets out of hwio header
+    - drm/msm/dpu: Remove duplicate register defines from INTF
+    - dt-bindings: display/msm: dsi-controller-main: Document qcom, master-dsi and
+      qcom, sync-dual-dsi
+    - ASoC: fsl_micfil: Fix error handler with pm_runtime_enable
+    - cpupower: Make TSC read per CPU for Mperf monitor
+    - af_key: Reject optional tunnel/BEET mode templates in outbound policies
+    - selftests: seg6: disable DAD on IPv6 router cfg for srv6_end_dt4_l3vpn_test
+    - selftets: seg6: disable rp_filter by default in srv6_end_dt4_l3vpn_test
+    - net: fec: Better handle pm_runtime_get() failing in .remove()
+    - net: phy: dp83867: add w/a for packet errors seen with short cables
+    - ALSA: firewire-digi00x: prevent potential use after free
+    - ALSA: hda/realtek: Apply HP B&O top speaker profile to Pavilion 15
+    - vsock: avoid to close connected socket after the timeout
+    - tcp: fix possible sk_priority leak in tcp_v4_send_reset()
+    - serial: arc_uart: fix of_iomap leak in `arc_serial_probe`
+    - serial: 8250_bcm7271: balance clk_enable calls
+    - serial: 8250_bcm7271: fix leak in `brcmuart_probe`
+    - erspan: get the proto with the md version for collect_md
+    - net: hns3: fix output information incomplete for dumping tx queue info with
+      debugfs
+    - net: hns3: fix sending pfc frames after reset issue
+    - net: hns3: fix reset delay time to avoid configuration timeout
+    - media: netup_unidvb: fix use-after-free at del_timer()
+    - SUNRPC: double free xprt_ctxt while still in use
+    - tracing: Introduce helpers to safely handle dynamic-sized sockaddrs
+    - SUNRPC: Clean up svc_deferred_class trace events
+    - SUNRPC: Remove dead code in svc_tcp_release_rqst()
+    - SUNRPC: Remove svc_rqst::rq_xprt_hlen
+    - SUNRPC: always free ctxt when freeing deferred request
+    - SUNRPC: Fix trace_svc_register() call site
+    - drm/exynos: fix g2d_open/close helper function definitions
+    - net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
+    - virtio-net: Maintain reverse cleanup order
+    - virtio_net: Fix error unwinding of XDP initialization
+    - tipc: add tipc_bearer_min_mtu to calculate min mtu
+    - tipc: do not update mtu if msg_max is too small in mtu negotiation
+    - tipc: check the bearer min mtu properly when setting it by netlink
+    - s390/cio: include subchannels without devices also for evaluation
+    - net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()
+    - net: bcmgenet: Restore phy_stop() depending upon suspend/close
+    - wifi: mac80211: fix min center freq offset tracing
+    - wifi: iwlwifi: mvm: fix cancel_delayed_work_sync() deadlock
+    - wifi: iwlwifi: mvm: don't trust firmware n_channels
+    - scsi: storvsc: Don't pass unused PFNs to Hyper-V host
+    - cassini: Fix a memory leak in the error handling path of cas_init_one()
+    - net: dsa: mv88e6xxx: Fix mv88e6393x EPC write command offset
+    - igb: fix bit_shift to be in [1..8] range
+    - vlan: fix a potential uninit-value in vlan_dev_hard_start_xmit()
+    - netfilter: nf_tables: fix nft_trans type confusion
+    - netfilter: nft_set_rbtree: fix null deref on element insertion
+    - bridge: always declare tunnel functions
+    - ALSA: usb-audio: Add a sample rate workaround for Line6 Pod Go
+    - USB: usbtmc: Fix direction for 0-length ioctl control messages
+    - usb-storage: fix deadlock when a scsi command timeouts more than once
+    - USB: UHCI: adjust zhaoxin UHCI controllers OverCurrent bit value
+    - usb: dwc3: debugfs: Resume dwc3 before accessing registers
+    - usb: gadget: u_ether: Fix host MAC address case
+    - usb: typec: altmodes/displayport: fix pin_assignment_show
+    - xhci-pci: Only run d3cold avoidance quirk for s2idle
+    - xhci: Fix incorrect tracking of free space on transfer rings
+    - ALSA: hda: Fix Oops by 9.1 surround channel names
+    - ALSA: hda: Add NVIDIA codec IDs a3 through a7 to patch table
+    - ALSA: hda/realtek: Add quirk for Clevo L140AU
+    - ALSA: hda/realtek: Add a quirk for HP EliteDesk 805
+    - ALSA: hda/realtek: Add quirk for 2nd ASUS GU603
+    - can: j1939: recvmsg(): allow MSG_CMSG_COMPAT flag
+    - can: isotp: recvmsg(): allow MSG_CMSG_COMPAT flag
+    - can: kvaser_pciefd: Set CAN_STATE_STOPPED in kvaser_pciefd_stop()
+    - can: kvaser_pciefd: Call request_irq() before enabling interrupts
+    - can: kvaser_pciefd: Empty SRB buffer in probe
+    - can: kvaser_pciefd: Clear listen-only bit if not explicitly requested
+    - can: kvaser_pciefd: Do not send EFLUSH command on TFD interrupt
+    - can: kvaser_pciefd: Disable interrupts in probe error path
+    - SMB3: Close all deferred handles of inode in case of handle lease break
+    - SMB3: drop reference to cfile before sending oplock break
+    - ksmbd: smb2: Allow messages padded to 8byte boundary
+    - ksmbd: allocate one more byte for implied bcc[0]
+    - ksmbd: fix wrong UserName check in session_user
+    - ksmbd: fix global-out-of-bounds in smb2_find_context_vals
+    - statfs: enforce statfs[64] structure initialization
+    - serial: Add support for Advantech PCI-1611U card
+    - serial: 8250_exar: Add support for USR298x PCI Modems
+    - serial: qcom-geni: fix enabling deactivated interrupt
+    - thunderbolt: Clear registers properly when auto clear isn't in use
+    - vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF
+    - ceph: force updating the msg pointer in non-split case
+    - powerpc/iommu: Incorrect DDW Table is referenced for SR-IOV device
+    - tpm/tpm_tis: Disable interrupts for more Lenovo devices
+    - powerpc/64s/radix: Fix soft dirty tracking
+    - nilfs2: fix use-after-free bug of nilfs_root in nilfs_evict_inode()
+    - s390/qdio: fix do_sqbs() inline assembly constraint
+    - HID: wacom: Force pen out of prox if no events have been received in a while
+    - HID: wacom: Add new Intuos Pro Small (PTH-460) device IDs
+    - HID: wacom: add three styli to wacom_intuos_get_tool_type
+    - Linux 5.15.113
+  * Jammy update: v5.15.112 upstream stable release (LP: #2026607)
+    - ring-buffer: Ensure proper resetting of atomic variables in
+      ring_buffer_reset_online_cpus
+    - crypto: ccp - Clear PSP interrupt status register before calling handler
+    - ubifs: Fix AA deadlock when setting xattr for encrypted file
+    - ubifs: Fix memory leak in do_rename
+    - bus: mhi: Move host MHI code to "host" directory
+    - bus: mhi: host: Remove duplicate ee check for syserr
+    - bus: mhi: host: Use mhi_tryset_pm_state() for setting fw error state
+    - bus: mhi: host: Range check CHDBOFF and ERDBOFF
+    - mailbox: zynq: Switch to flexible array to simplify code
+    - mailbox: zynqmp: Fix counts of child nodes
+    - ASoC: soc-pcm: use GFP_ATOMIC for dpcm structure
+    - ASoC: soc-pcm: align BE 'atomicity' with that of the FE
+    - ASoC: soc-pcm: Fix and cleanup DPCM locking
+    - ASoC: soc-pcm: serialize BE triggers
+    - ASoC: soc-pcm: test refcount before triggering
+    - ASoC: soc-pcm: fix BE handling of PAUSE_RELEASE
+    - fs/ntfs3: Fix null-ptr-deref on inode->i_op in ntfs_lookup()
+    - drm/hyperv: Don't overwrite dirt_needed value set by host
+    - scsi: qedi: Fix use after free bug in qedi_remove()
+    - net/ncsi: clear Tx enable mode when handling a Config required AEN
+    - net/sched: cls_api: remove block_cb from driver_list before freeing
+    - sit: update dev->needed_headroom in ipip6_tunnel_bind_dev()
+    - selftests: srv6: make srv6_end_dt46_l3vpn_test more robust
+    - net: dsa: mv88e6xxx: add mv88e6321 rsvd2cpu
+    - writeback: fix call of incorrect macro
+    - watchdog: dw_wdt: Fix the error handling path of dw_wdt_drv_probe()
+    - RISC-V: mm: Enable huge page support to kernel_page_present() function
+    - net/sched: act_mirred: Add carrier check
+    - r8152: fix flow control issue of RTL8156A
+    - r8152: fix the poor throughput for 2.5G devices
+    - r8152: move setting r8153b_rx_agg_chg_indicate()
+    - sfc: Fix module EEPROM reporting for QSFP modules
+    - rxrpc: Fix hard call timeout units
+    - octeontx2-af: Secure APR table update with the lock
+    - octeontx2-af: Skip PFs if not enabled
+    - octeontx2-pf: Disable packet I/O for graceful exit
+    - octeontx2-vf: Detach LF resources on probe cleanup
+    - ionic: remove noise from ethtool rxnfc error msg
+    - ethtool: Fix uninitialized number of lanes
+    - ionic: catch failure from devlink_alloc
+    - af_packet: Don't send zero-byte data in packet_sendmsg_spkt().
+    - drm/amdgpu: add a missing lock for AMDGPU_SCHED
+    - ALSA: caiaq: input: Add error handling for unsupported input methods in
+      `snd_usb_caiaq_input_init`
+    - net: dsa: mt7530: fix corrupt frames using trgmii on 40 MHz XTAL MT7621
+    - virtio_net: split free_unused_bufs()
+    - virtio_net: suppress cpu stall when free_unused_bufs
+    - net: enetc: check the index of the SFI rather than the handle
+    - perf scripts intel-pt-events.py: Fix IPC output for Python 2
+    - perf vendor events power9: Remove UTF-8 characters from JSON files
+    - perf pmu: zfree() expects a pointer to a pointer to zero it after freeing
+      its contents
+    - perf map: Delete two variable initialisations before null pointer checks in
+      sort__sym_from_cmp()
+    - crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
+    - crypto: engine - check if BH is disabled during completion
+    - crypto: api - Add scaffolding to change completion function signature
+    - crypto: engine - Use crypto_request_complete
+    - crypto: engine - fix crypto_queue backlog handling
+    - perf symbols: Fix return incorrect build_id size in elf_read_build_id()
+    - perf evlist: Refactor evlist__for_each_cpu()
+    - perf stat: Separate bperf from bpf_profiler
+    - btrfs: fix btrfs_prev_leaf() to not return the same key twice
+    - btrfs: zoned: fix wrong use of bitops API in btrfs_ensure_empty_zones
+    - btrfs: fix encoded write i_size corruption with no-holes
+    - btrfs: don't free qgroup space unless specified
+    - btrfs: zero the buffer before marking it dirty in btrfs_redirty_list_add
+    - btrfs: print-tree: parent bytenr must be aligned to sector size
+    - btrfs: fix space cache inconsistency after error loading it from disk
+    - cifs: fix pcchunk length type in smb2_copychunk_range
+    - cifs: release leases for deferred close handles when freezing
+    - platform/x86: touchscreen_dmi: Add upside-down quirk for GDIX1002 ts on the
+      Juno Tablet
+    - platform/x86: touchscreen_dmi: Add info for the Dexp Ursus KX210i
+    - inotify: Avoid reporting event with invalid wd
+    - smb3: fix problem remounting a share after shutdown
+    - SMB3: force unmount was failing to close deferred close files
+    - sh: math-emu: fix macro redefined warning
+    - sh: mcount.S: fix build error when PRINTK is not enabled
+    - sh: init: use OF_EARLY_FLATTREE for early init
+    - sh: nmi_debug: fix return value of __setup handler
+    - remoteproc: stm32: Call of_node_put() on iteration error
+    - remoteproc: st: Call of_node_put() on iteration error
+    - remoteproc: imx_rproc: Call of_node_put() on iteration error
+    - ARM: dts: exynos: fix WM8960 clock name in Itop Elite
+    - ARM: dts: s5pv210: correct MIPI CSIS clock name
+    - drm/bridge: lt8912b: Fix DSI Video Mode
+    - drm/msm: fix NULL-deref on snapshot tear down
+    - drm/msm: fix NULL-deref on irq uninstall
+    - f2fs: fix potential corruption when moving a directory
+    - drm/panel: otm8009a: Set backlight parent to panel device
+    - drm/amd/display: fix flickering caused by S/G mode
+    - drm/amdgpu: fix an amdgpu_irq_put() issue in gmc_v9_0_hw_fini()
+    - drm/amdgpu/gfx: disable gfx9 cp_ecc_error_irq only when enabling legacy gfx
+      ras
+    - drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)
+    - drm/amdgpu: disable sdma ecc irq only when sdma RAS is enabled in suspend
+    - HID: wacom: Set a default resolution for older tablets
+    - HID: wacom: insert timestamp to packed Bluetooth (BT) events
+    - fs/ntfs3: Refactoring of various minor issues
+    - ASoC: soc-pcm: Fix DPCM lockdep warning due to nested stream locks
+    - ASoC: soc-compress: Inherit atomicity from DAI link for Compress FE
+    - ASoC: soc-pcm: Move debugfs removal out of spinlock
+    - ASoC: DPCM: Don't pick up BE without substream
+    - ASoC: soc-pcm.c: call __soc_pcm_close() in soc_pcm_close()
+    - drm/i915/dg2: Support 4k@30 on HDMI
+    - drm/i915/dg2: Add additional HDMI pixel clock frequencies
+    - drm/i915/dg2: Add HDMI pixel clock frequencies 267.30 and 319.89 MHz
+    - drm/msm: Remove struct_mutex usage
+    - drm/msm/adreno: fix runtime PM imbalance at gpu load
+    - drm/amd/display: Refine condition of cursor visibility for pipe-split
+    - drm/amd/display: Add NULL plane_state check for cursor disable logic
+    - wifi: rtw88: rtw8821c: Fix rfe_option field width
+    - ksmbd: set RSS capable in FSCTL_QUERY_NETWORK_INTERFACE_INFO
+    - ksmbd: fix multi session connection failure
+    - ksmbd: replace sessions list in connection with xarray
+    - ksmbd: add channel rwlock
+    - ksmbd: fix kernel oops from idr_remove()
+    - ksmbd: fix racy issue while destroying session on multichannel
+    - ksmbd: fix deadlock in ksmbd_find_crypto_ctx()
+    - ksmbd: not allow guest user on multichannel
+    - locking/rwsem: Add __always_inline annotation to __down_read_common() and
+      inlined callers
+    - ext4: fix WARNING in mb_find_extent
+    - ext4: avoid a potential slab-out-of-bounds in ext4_group_desc_csum
+    - ext4: fix data races when using cached status extents
+    - ext4: check iomap type only if ext4_iomap_begin() does not fail
+    - ext4: improve error recovery code paths in __ext4_remount()
+    - ext4: improve error handling from ext4_dirhash()
+    - ext4: fix deadlock when converting an inline directory in nojournal mode
+    - ext4: add bounds checking in get_max_inline_xattr_value_size()
+    - ext4: bail out of ext4_xattr_ibody_get() fails for any reason
+    - ext4: remove a BUG_ON in ext4_mb_release_group_pa()
+    - ext4: fix invalid free tracking in ext4_xattr_move_to_block()
+    - drm/msm/adreno: adreno_gpu: Use suspend() instead of idle() on load error
+    - serial: 8250: Fix serial8250_tx_empty() race with DMA Tx
+    - drbd: correctly submit flush bio on barrier
+    - RISC-V: Fix up a cherry-pick warning in setup_vm_final()
+    - drm/amd/display: Fix hang when skipping modeset
+    - Linux 5.15.112
+  * CVE-2023-31084 // CVE-2023-31084 was assigned to this bug.
+    - media: dvb-core: Fix kernel WARNING for blocking operation in wait_event*()
+  * CVE-2023-3776
+    - net/sched: cls_fw: Fix improper refcount update leads to use-after-free
+
+  [ Ubuntu: 5.15.0-79.86 ]
+
+  * jammy/linux: 5.15.0-79.86 -proposed tracker (LP: #2026531)
+  * Jammy update: v5.15.111 upstream stable release (LP: #2025095)
+    - ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15
+    - ASoC: soc-pcm: fix hw->formats cleared by soc_pcm_hw_init() for dpcm
+    - x86/hyperv: Block root partition functionality in a Confidential VM
+    - iio: adc: palmas_gpadc: fix NULL dereference on rmmod
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Acer Iconia One 7 B1-750
+    - selftests mount: Fix mount_setattr_test builds failed
+    - asm-generic/io.h: suppress endianness warnings for readq() and writeq()
+    - x86/cpu: Add model number for Intel Arrow Lake processor
+    - wireguard: timers: cast enum limits members to int in prints
+    - wifi: mt76: mt7921e: Set memory space enable in PCI_COMMAND if unset
+    - arm64: Always load shadow stack pointer directly from the task struct
+    - arm64: Stash shadow stack pointer in the task struct on interrupt
+    - PCI: pciehp: Fix AB-BA deadlock between reset_lock and device_lock
+    - PCI: qcom: Fix the incorrect register usage in v2.7.0 config
+    - IMA: allow/fix UML builds
+    - USB: dwc3: fix runtime pm imbalance on probe errors
+    - USB: dwc3: fix runtime pm imbalance on unbind
+    - hwmon: (k10temp) Check range scale when CUR_TEMP register is read-write
+    - hwmon: (adt7475) Use device_property APIs when configuring polarity
+    - posix-cpu-timers: Implement the missing timer_wait_running callback
+    - blk-mq: release crypto keyslot before reporting I/O complete
+    - blk-crypto: make blk_crypto_evict_key() return void
+    - blk-crypto: make blk_crypto_evict_key() more robust
+    - ext4: use ext4_journal_start/stop for fast commit transactions
+    - staging: iio: resolver: ads1210: fix config mode
+    - tty: Prevent writing chars during tcsetattr TCSADRAIN/FLUSH
+    - xhci: fix debugfs register accesses while suspended
+    - tick/nohz: Fix cpu_is_hotpluggable() by checking with nohz subsystem
+    - MIPS: fw: Allow firmware to pass a empty env
+    - ipmi:ssif: Add send_retries increment
+    - ipmi: fix SSIF not responding under certain cond.
+    - kheaders: Use array declaration instead of char
+    - wifi: mt76: add missing locking to protect against concurrent rx/status
+      calls
+    - pwm: meson: Fix axg ao mux parents
+    - pwm: meson: Fix g12a ao clk81 name
+    - soundwire: qcom: correct setting ignore bit on v1.5.1
+    - pinctrl: qcom: lpass-lpi: set output value before enabling output
+    - ring-buffer: Sync IRQ works before buffer destruction
+    - crypto: api - Demote BUG_ON() in crypto_unregister_alg() to a WARN_ON()
+    - crypto: safexcel - Cleanup ring IRQ workqueues on load failure
+    - rcu: Avoid stack overflow due to __rcu_irq_enter_check_tick() being kprobe-
+      ed
+    - reiserfs: Add security prefix to xattr name in reiserfs_security_write()
+    - KVM: nVMX: Emulate NOPs in L2, and PAUSE if it's not intercepted
+    - relayfs: fix out-of-bounds access in relay_file_read
+    - writeback, cgroup: fix null-ptr-deref write in bdi_split_work_to_wbs
+    - ksmbd: call rcu_barrier() in ksmbd_server_exit()
+    - ksmbd: fix NULL pointer dereference in smb2_get_info_filesystem()
+    - ksmbd: fix memleak in session setup
+    - i2c: omap: Fix standard mode false ACK readings
+    - riscv: mm: remove redundant parameter of create_fdt_early_page_table
+    - tracing: Fix permissions for the buffer_percent file
+    - iommu/amd: Fix "Guest Virtual APIC Table Root Pointer" configuration in IRTE
+    - ubifs: Fix memleak when insert_old_idx() failed
+    - ubi: Fix return value overwrite issue in try_write_vid_and_data()
+    - ubifs: Free memory for tmpfile name
+    - xfs: don't consider future format versions valid
+    - sound/oss/dmasound: fix build when drivers are mixed =y/=m
+    - rcu: Fix missing TICK_DEP_MASK_RCU_EXP dependency check
+    - selftests/resctrl: Return NULL if malloc_and_init_memory() did not alloc mem
+    - selftests/resctrl: Extend CPU vendor detection
+    - selftests/resctrl: Move ->setup() call outside of test specific branches
+    - selftests/resctrl: Allow ->setup() to return errors
+    - selftests/resctrl: Check for return value after write_schemata()
+    - selinux: fix Makefile dependencies of flask.h
+    - selinux: ensure av_permissions.h is built when needed
+    - tpm, tpm_tis: Do not skip reset of original interrupt vector
+    - tpm, tpm_tis: Claim locality before writing TPM_INT_ENABLE register
+    - tpm, tpm_tis: Disable interrupts if tpm_tis_probe_irq() failed
+    - tpm, tpm_tis: Claim locality before writing interrupt registers
+    - tpm, tpm: Implement usage counter for locality
+    - tpm, tpm_tis: Claim locality when interrupts are reenabled on resume
+    - erofs: stop parsing non-compact HEAD index if clusterofs is invalid
+    - erofs: fix potential overflow calculating xattr_isize
+    - drm/rockchip: Drop unbalanced obj unref
+    - drm/vgem: add missing mutex_destroy
+    - drm/probe-helper: Cancel previous job before starting new one
+    - tools/x86/kcpuid: Fix avx512bw and avx512lvl fields in Fn00000007
+    - soc: ti: pm33xx: Fix refcount leak in am33xx_pm_probe
+    - arm64: dts: renesas: r8a77990: Remove bogus voltages from OPP table
+    - arm64: dts: renesas: r8a774c0: Remove bogus voltages from OPP table
+    - drm/msm/disp/dpu: check for crtc enable rather than crtc active to release
+      shared resources
+    - EDAC/skx: Fix overflows on the DRAM row address mapping arrays
+    - regulator: core: Shorten off-on-delay-us for always-on/boot-on by time since
+      booted
+    - arm64: dts: ti: k3-j721e-main: Remove ti,strobe-sel property
+    - arm64: dts: broadcom: bcm4908: add DT for Netgear RAXE500
+    - arm64: dts: Add DTS files for bcmbca SoC BCM63158
+    - arm64: dts: Add DTS files for bcmbca SoC BCM4912
+    - ARM64: dts: Add DTS files for bcmbca SoC BCM6858
+    - arm64: dts: Add base DTS file for bcmbca device Asus GT-AX6000
+    - arm64: dts: Move BCM4908 dts to bcmbca folder
+    - arm64: dts: broadcom: bcmbca: bcm4908: fix NAND interrupt name
+    - arm64: dts: broadcom: bcmbca: bcm4908: fix procmon nodename
+    - arm64: dts: qcom: msm8998: Fix stm-stimulus-base reg name
+    - arm64: dts: qcom: sdm845: correct dynamic power coefficients
+    - arm64: dts: qcom: sdm845: Fix the PCI I/O port range
+    - arm64: dts: qcom: msm8998: Fix the PCI I/O port range
+    - arm64: dts: qcom: ipq8074: Fix the PCI I/O port range
+    - arm64: dts: qcom: ipq6018: Fix the PCI I/O port range
+    - arm64: dts: qcom: msm8996: Fix the PCI I/O port range
+    - arm64: dts: qcom: sm8250: Fix the PCI I/O port range
+    - ARM: dts: qcom: ipq4019: Fix the PCI I/O port range
+    - ARM: dts: qcom: ipq8064: reduce pci IO size to 64K
+    - ARM: dts: qcom: ipq8064: Fix the PCI I/O port range
+    - x86/MCE/AMD: Use an u64 for bank_map
+    - media: bdisp: Add missing check for create_workqueue
+    - media: av7110: prevent underflow in write_ts_to_decoder()
+    - firmware: qcom_scm: Clear download bit during reboot
+    - drm/bridge: adv7533: Fix adv7533_mode_valid for adv7533 and adv7535
+    - media: max9286: Free control handler
+    - drm/msm/adreno: Defer enabling runpm until hw_init()
+    - drm/msm/adreno: drop bogus pm_runtime_set_active()
+    - drm: msm: adreno: Disable preemption on Adreno 510
+    - drm/amd/display/dc/dce60/Makefile: Fix previous attempt to silence known
+      override-init warnings
+    - ACPI: processor: Fix evaluating _PDC method when running as Xen dom0
+    - mmc: sdhci-of-esdhc: fix quirk to ignore command inhibit for data
+    - drm: rcar-du: Fix a NULL vs IS_ERR() bug
+    - ARM: dts: gta04: fix excess dma channel usage
+    - firmware: arm_scmi: Fix xfers allocation on Rx channel
+    - ACPI: VIOT: Initialize the correct IOMMU fwspec
+    - drm/lima/lima_drv: Add missing unwind goto in lima_pdev_probe()
+    - mailbox: mpfs: switch to txdone_poll
+    - arm64: dts: qcom: sc7180-trogdor-lazor: correct trackpad supply
+    - arm64: dts: qcom: msm8994-kitakami: drop unit address from PMI8994 regulator
+    - arm64: dts: qcom: msm8994-msft-lumia-octagon: drop unit address from PMI8994
+      regulator
+    - drm/ttm: optimize pool allocations a bit v2
+    - drm/ttm/pool: Fix ttm_pool_alloc error path
+    - regulator: core: Consistently set mutex_owner when using
+      ww_mutex_lock_slow()
+    - regulator: core: Avoid lockdep reports when resolving supplies
+    - x86/apic: Fix atomic update of offset in reserve_eilvt_offset()
+    - media: rkvdec: fix use after free bug in rkvdec_remove
+    - media: dm1105: Fix use after free bug in dm1105_remove due to race condition
+    - media: saa7134: fix use after free bug in saa7134_finidev due to race
+      condition
+    - media: rcar_fdp1: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - media: rcar_fdp1: Fix the correct variable assignments
+    - platform: Provide a remove callback that returns no value
+    - media: rcar_fdp1: Convert to platform remove callback returning void
+    - media: rcar_fdp1: Fix refcount leak in probe and remove function
+    - drm/amd/display: Fix potential null dereference
+    - media: rc: gpio-ir-recv: Fix support for wake-up
+    - media: venus: dec: Fix handling of the start cmd
+    - regulator: stm32-pwr: fix of_iomap leak
+    - x86/ioapic: Don't return 0 from arch_dynirq_lower_bound()
+    - arm64: kgdb: Set PSTATE.SS to 1 to re-enable single-step
+    - debugobject: Prevent init race with static objects
+    - drm/i915: Make intel_get_crtc_new_encoder() less oopsy
+    - tick/common: Align tick period with the HZ tick.
+    - cpufreq: use correct unit when verify cur freq
+    - hwmon: (pmbus/fsp-3y) Fix functionality bitmask in FSP-3Y YM-2151E
+    - wifi: ath6kl: minor fix for allocation size
+    - wifi: ath9k: hif_usb: fix memory leak of remain_skbs
+    - wifi: ath5k: fix an off by one check in ath5k_eeprom_read_freq_list()
+    - wifi: brcmfmac: support CQM RSSI notification with older firmware
+    - wifi: ath6kl: reduce WARN to dev_dbg() in callback
+    - tools: bpftool: Remove invalid \' json escape
+    - wifi: rtw88: mac: Return the original error from rtw_pwr_seq_parser()
+    - wifi: rtw88: mac: Return the original error from rtw_mac_power_switch()
+    - bpf: take into account liveness when propagating precision
+    - bpf: fix precision propagation verbose logging
+    - scm: fix MSG_CTRUNC setting condition for SO_PASSSEC
+    - selftests/bpf: Fix a fd leak in an error path in network_helpers.c
+    - bpf: Remove misleading spec_v1 check on var-offset stack read
+    - net: pcs: xpcs: remove double-read of link state when using AN
+    - vlan: partially enable SIOCSHWTSTAMP in container
+    - net/packet: annotate accesses to po->xmit
+    - net/packet: convert po->origdev to an atomic flag
+    - net/packet: convert po->auxdata to an atomic flag
+    - scsi: target: Fix multiple LUN_RESET handling
+    - scsi: target: iscsit: Fix TAS handling during conn cleanup
+    - scsi: megaraid: Fix mega_cmd_done() CMDID_INT_CMDS
+    - f2fs: handle dqget error in f2fs_transfer_project_quota()
+    - f2fs: enforce single zone capacity
+    - f2fs: apply zone capacity to all zone type
+    - f2fs: compress: fix to call f2fs_wait_on_page_writeback() in
+      f2fs_write_raw_pages()
+    - crypto: caam - Clear some memory in instantiate_rng
+    - crypto: sa2ul - Select CRYPTO_DES
+    - wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_rfreg()
+    - wifi: rtlwifi: fix incorrect error codes in rtl_debugfs_set_write_reg()
+    - wifi: rt2x00: Fix memory leak when handling surveys
+    - net: qrtr: correct types of trace event parameters
+    - selftests: xsk: Disable IPv6 on VETH1
+    - selftests/bpf: Wait for receive in cg_storage_multi test
+    - bpftool: Fix bug for long instructions in program CFG dumps
+    - crypto: drbg - make drbg_prepare_hrng() handle jent instantiation errors
+    - crypto: drbg - Only fail when jent is unavailable in FIPS mode
+    - xsk: Fix unaligned descriptor validation
+    - f2fs: fix to avoid use-after-free for cached IPU bio
+    - scsi: lpfc: Fix ioremap issues in lpfc_sli4_pci_mem_setup()
+    - net: ethernet: stmmac: dwmac-rk: fix optional phy regulator handling
+    - bpf, sockmap: fix deadlocks in the sockhash and sockmap
+    - nvmet: use i_size_read() to set size for file-ns
+    - nvmet: move the call to nvmet_ns_changed out of nvmet_ns_revalidate
+    - nvmet: fix error handling in nvmet_execute_identify_cns_cs_ns()
+    - nvmet: fix Identify Namespace handling
+    - nvmet: fix Identify Controller handling
+    - nvmet: fix Identify Active Namespace ID list handling
+    - nvmet: fix I/O Command Set specific Identify Controller
+    - nvme: handle the persistent internal error AER
+    - nvme: fix async event trace event
+    - nvme-fcloop: fix "inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage"
+    - selftests/bpf: Fix leaked bpf_link in get_stackid_cannot_attach
+    - bpf, sockmap: Revert buggy deadlock fix in the sockhash and sockmap
+    - md: drop queue limitation for RAID1 and RAID10
+    - md: raid10 add nowait support
+    - md/raid10: factor out code from wait_barrier() to stop_waiting_barrier()
+    - md/raid10: fix task hung in raid10d
+    - md/raid10: fix leak of 'r10bio->remaining' for recovery
+    - md/raid10: fix memleak for 'conf->bio_split'
+    - md/raid10: fix memleak of md thread
+    - md/raid10: don't call bio_start_io_acct twice for bio which experienced read
+      error
+    - wifi: iwlwifi: yoyo: skip dump correctly on hw error
+    - wifi: iwlwifi: yoyo: Fix possible division by zero
+    - wifi: iwlwifi: mvm: initialize seq variable
+    - wifi: iwlwifi: fw: move memset before early return
+    - jdb2: Don't refuse invalidation of already invalidated buffers
+    - wifi: iwlwifi: make the loop for card preparation effective
+    - wifi: mt76: handle failure of vzalloc in mt7615_coredump_work
+    - wifi: mt76: add flexible polling wait-interval support
+    - wifi: mt76: mt7921e: fix probe timeout after reboot
+    - wifi: mt76: fix 6GHz high channel not be scanned
+    - wifi: mt76: mt7921e: improve reliability of dma reset
+    - wifi: iwlwifi: mvm: check firmware response size
+    - wifi: iwlwifi: fw: fix memory leak in debugfs
+    - ixgbe: Allow flow hash to be set via ethtool
+    - ixgbe: Enable setting RSS table to default values
+    - net/mlx5: E-switch, Don't destroy indirect table in split rule
+    - net: stmmac:fix system hang when setting up tag_8021q VLAN for DSA ports
+    - bpf: Don't EFAULT for getsockopt with optval=NULL
+    - netfilter: nf_tables: don't write table validation state without mutex
+    - net/sched: sch_fq: fix integer overflow of "credit"
+    - ipv4: Fix potential uninit variable access bug in __ip_make_skb()
+    - netlink: Use copy_to_user() for optval in netlink_getsockopt().
+    - net: amd: Fix link leak when verifying config failed
+    - tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
+    - ipmi: ASPEED_BT_IPMI_BMC: select REGMAP_MMIO instead of depending on it
+    - drivers: staging: rtl8723bs: Fix locking in _rtw_join_timeout_handler()
+    - drivers: staging: rtl8723bs: Fix locking in rtw_scan_timeout_handler()
+    - pstore: Revert pmsg_lock back to a normal mutex
+    - usb: host: xhci-rcar: remove leftover quirk handling
+    - usb: dwc3: gadget: Change condition for processing suspend event
+    - serial: stm32: re-introduce an irq flag condition in usart_receive_chars
+    - serial: stm32: Re-assert RTS/DE GPIO in RS485 mode only if more data are
+      transmitted
+    - fpga: bridge: fix kernel-doc parameter description
+    - iio: light: max44009: add missing OF device matching
+    - serial: 8250_bcm7271: Fix arbitration handling
+    - spi: spi-imx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
+    - spi: imx: Don't skip cleanup in remove's error path
+    - usb: gadget: udc: renesas_usb3: Fix use after free bug in
+      renesas_usb3_remove due to race condition
+    - PCI: imx6: Install the fault handler only on compatible match
+    - ASoC: es8316: Handle optional IRQ assignment
+    - linux/vt_buffer.h: allow either builtin or modular for macros
+    - spi: qup: Don't skip cleanup in remove's error path
+    - spi: fsl-spi: Fix CPM/QE mode Litte Endian
+    - vmci_host: fix a race condition in vmci_host_poll() causing GPF
+    - of: Fix modalias string generation
+    - PCI/EDR: Clear Device Status after EDR error recovery
+    - ia64: mm/contig: fix section mismatch warning/error
+    - ia64: salinfo: placate defined-but-not-used warning
+    - scripts/gdb: bail early if there are no clocks
+    - scripts/gdb: bail early if there are no generic PD
+    - HID: amd_sfh: Add support for shutdown operation
+    - coresight: etm_pmu: Set the module field
+    - ASoC: fsl_mqs: move of_node_put() to the correct location
+    - spi: cadence-quadspi: fix suspend-resume implementations
+    - i2c: cadence: cdns_i2c_master_xfer(): Fix runtime PM leak on error path
+    - scripts/gdb: raise error with reduced debugging information
+    - uapi/linux/const.h: prefer ISO-friendly __typeof__
+    - sh: sq: Fix incorrect element size for allocating bitmap buffer
+    - usb: gadget: tegra-xudc: Fix crash in vbus_draw
+    - usb: chipidea: fix missing goto in `ci_hdrc_probe`
+    - usb: mtu3: fix kernel panic at qmu transfer done irq handler
+    - firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe
+    - tty: serial: fsl_lpuart: adjust buffer length to the intended size
+    - serial: 8250: Add missing wakeup event reporting
+    - staging: rtl8192e: Fix W_DISABLE# does not work after stop/start
+    - spmi: Add a check for remove callback when removing a SPMI driver
+    - virtio_ring: don't update event idx on get_buf
+    - macintosh/windfarm_smu_sat: Add missing of_node_put()
+    - powerpc/mpc512x: fix resource printk format warning
+    - powerpc/wii: fix resource printk format warnings
+    - powerpc/sysdev/tsi108: fix resource printk format warnings
+    - macintosh: via-pmu-led: requires ATA to be set
+    - powerpc/rtas: use memmove for potentially overlapping buffer copy
+    - sched/fair: Use __schedstat_set() in set_next_entity()
+    - sched: Make struct sched_statistics independent of fair sched class
+    - sched/fair: Fix inaccurate tally of ttwu_move_affine
+    - perf/core: Fix hardlockup failure caused by perf throttle
+    - Revert "objtool: Support addition to set CFA base"
+    - sched/rt: Fix bad task migration for rt tasks
+    - clk: at91: clk-sam9x60-pll: fix return value check
+    - RDMA/siw: Fix potential page_array out of range access
+    - RDMA/rdmavt: Delete unnecessary NULL check
+    - workqueue: Introduce show_one_worker_pool and show_one_workqueue.
+    - workqueue: Fix hung time report of worker pools
+    - rtc: omap: include header for omap_rtc_power_off_program prototype
+    - RDMA/mlx4: Prevent shift wrapping in set_user_sq_size()
+    - rtc: meson-vrtc: Use ktime_get_real_ts64() to get the current time
+    - fs/ntfs3: Fix memory leak if ntfs_read_mft failed
+    - fs/ntfs3: Add check for kmemdup
+    - fs/ntfs3: Fix OOB read in indx_insert_into_buffer
+    - fs/ntfs3: Fix slab-out-of-bounds read in hdr_delete_de()
+    - power: supply: generic-adc-battery: fix unit scaling
+    - clk: add missing of_node_put() in "assigned-clocks" property parsing
+    - RDMA/siw: Remove namespace check from siw_netdev_event()
+    - clk: qcom: gcc-sm6115: Mark RCGs shared where applicable
+    - RDMA/cm: Trace icm_send_rej event before the cm state is reset
+    - RDMA/srpt: Add a check for valid 'mad_agent' pointer
+    - IB/hfi1: Fix SDMA mmu_rb_node not being evicted in LRU order
+    - IB/hfi1: Fix bugs with non-PAGE_SIZE-end multi-iovec user SDMA requests
+    - NFSv4.1: Always send a RECLAIM_COMPLETE after establishing lease
+    - clk: qcom: regmap: add PHY clock source implementation
+    - clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
+    - Input: raspberrypi-ts - fix refcount leak in rpi_ts_probe
+    - RDMA/mlx5: Fix flow counter query via DEVX
+    - SUNRPC: remove the maximum number of retries in call_bind_status
+    - RDMA/mlx5: Use correct device num_ports when modify DC
+    - clocksource/drivers/davinci: Fix memory leak in davinci_timer_register when
+      init fails
+    - openrisc: Properly store r31 to pt_regs on unhandled exceptions
+    - timekeeping: Fix references to nonexistent ktime_get_fast_ns()
+    - SMB3: Add missing locks to protect deferred close file list
+    - SMB3: Close deferred file handles in case of handle lease break
+    - ext4: fix i_disksize exceeding i_size problem in paritally written case
+    - ext4: fix use-after-free read in ext4_find_extent for bigalloc + inline
+    - pinctrl: renesas: r8a779a0: Remove incorrect AVB[01] pinmux configuration
+    - leds: TI_LMU_COMMON: select REGMAP instead of depending on it
+    - dmaengine: mv_xor_v2: Fix an error code.
+    - leds: tca6507: Fix error handling of using fwnode_property_read_string
+    - pwm: mtk-disp: Disable shadow registers before setting backlight values
+    - pwm: mtk-disp: Configure double buffering before reading in .get_state()
+    - phy: tegra: xusb: Add missing tegra_xusb_port_unregister for usb2_port and
+      ulpi_port
+    - dma: gpi: remove spurious unlock in gpi_ch_init
+    - dmaengine: dw-edma: Fix to change for continuous transfer
+    - dmaengine: dw-edma: Fix to enable to issue dma request on DMA processing
+    - dmaengine: at_xdmac: Fix concurrency over chan's completed_cookie
+    - dmaengine: at_xdmac: Fix race for the tx desc callback
+    - dmaengine: at_xdmac: do not enable all cyclic channels
+    - thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in
+      mtk_thermal_probe
+    - mfd: tqmx86: Do not access I2C_DETECT register through io_base
+    - mfd: tqmx86: Specify IO port register range more precisely
+    - mfd: tqmx86: Correct board names for TQMxE39x
+    - afs: Fix updating of i_size with dv jump from server
+    - parisc: Fix argument pointer in real64_call_asm()
+    - ALSA: usb-audio: Add quirk for Pioneer DDJ-800
+    - nilfs2: do not write dirty data after degenerating to read-only
+    - nilfs2: fix infinite loop in nilfs_mdt_get_block()
+    - md/raid10: fix null-ptr-deref in raid10_sync_request
+    - mtd: core: provide unique name for nvmem device, take two
+    - mtd: core: fix nvmem error reporting
+    - mtd: core: fix error path for nvmem provider
+    - mailbox: zynqmp: Fix IPI isr handling
+    - mailbox: zynqmp: Fix typo in IPI documentation
+    - wifi: rtl8xxxu: RTL8192EU always needs full init
+    - clk: rockchip: rk3399: allow clk_cifout to force clk_cifout_src to reparent
+    - scripts/gdb: fix lx-timerlist for Python3
+    - btrfs: scrub: reject unsupported scrub flags
+    - s390/dasd: fix hanging blockdevice after request requeue
+    - ia64: fix an addr to taddr in huge_pte_offset()
+    - dm verity: fix error handling for check_at_most_once on FEC
+    - dm clone: call kmem_cache_destroy() in dm_clone_init() error path
+    - dm integrity: call kmem_cache_destroy() in dm_integrity_init() error path
+    - dm flakey: fix a crash with invalid table line
+    - dm ioctl: fix nested locking in table_clear() to remove deadlock concern
+    - dm: don't lock fs when the map is NULL in process of resume
+    - perf auxtrace: Fix address filter entire kernel size
+    - perf intel-pt: Fix CYC timestamps after standalone CBR
+    - sound/oss/dmasound: fix 'dmasound_setup' defined but not used
+    - arm64: dts: qcom: sdm845: correct dynamic power coefficients - again
+    - sched: Fix DEBUG && !SCHEDSTATS warn
+    - Linux 5.15.111
+  * Jammy update: v5.15.110 upstream stable release (LP: #2025090)
+    - PCI/ASPM: Remove pcie_aspm_pm_state_change()
+    - selftests/kselftest/runner/run_one(): allow running non-executable files
+    - KVM: arm64: Retry fault if vma_lookup() results become invalid
+    - KVM: arm64: Fix buffer overflow in kvm_arm_set_fw_reg()
+    - drm/fb-helper: set x/yres_virtual in drm_fb_helper_check_var
+    - bluetooth: Perform careful capability checks in hci_sock_ioctl()
+    - USB: serial: option: add UNISOC vendor and TOZED LT70C product
+    - driver core: Don't require dynamic_debug for initcall_debug probe timing
+    - selftests: mptcp: join: fix "invalid address, ADD_ADDR timeout"
+    - riscv: Move early dtb mapping into the fixmap region
+    - riscv: Do not set initial_boot_params to the linear address of the dtb
+    - riscv: No need to relocate the dtb as it lies in the fixmap region
+    - Linux 5.15.110
+  * Jammy update: v5.15.109 upstream stable release (LP: #2024265)
+    - ARM: dts: rockchip: fix a typo error for rk3288 spdif node
+    - arm64: dts: qcom: ipq8074-hk01: enable QMP device, not the PHY node
+    - arm64: dts: meson-g12-common: specify full DMC range
+    - arm64: dts: imx8mm-evk: correct pmic clock source
+    - netfilter: br_netfilter: fix recent physdev match breakage
+    - regulator: fan53555: Explicitly include bits header
+    - regulator: fan53555: Fix wrong TCS_SLEW_MASK
+    - virtio_net: bugfix overflow inside xdp_linearize_page()
+    - sfc: Split STATE_READY in to STATE_NET_DOWN and STATE_NET_UP.
+    - sfc: Fix use-after-free due to selftest_work
+    - netfilter: nf_tables: fix ifdef to also consider nf_tables=m
+    - i40e: fix accessing vsi->active_filters without holding lock
+    - i40e: fix i40e_setup_misc_vector() error handling
+    - netfilter: nf_tables: validate catch-all set elements
+    - netfilter: nf_tables: tighten netlink attribute requirements for catch-all
+      elements
+    - bnxt_en: Do not initialize PTP on older P3/P4 chips
+    - mlxfw: fix null-ptr-deref in mlxfw_mfa2_tlv_next()
+    - bonding: Fix memory leak when changing bond type to Ethernet
+    - net: rpl: fix rpl header size calculation
+    - mlxsw: pci: Fix possible crash during initialization
+    - spi: spi-rockchip: Fix missing unwind goto in rockchip_sfc_probe()
+    - bpf: Fix incorrect verifier pruning due to missing register precision taints
+    - e1000e: Disable TSO on i219-LM card to increase speed
+    - f2fs: Fix f2fs_truncate_partial_nodes ftrace event
+    - Input: i8042 - add quirk for Fujitsu Lifebook A574/H
+    - platform/x86 (gigabyte-wmi): Add support for A320M-S2H V2
+    - selftests: sigaltstack: fix -Wuninitialized
+    - scsi: megaraid_sas: Fix fw_crash_buffer_show()
+    - scsi: core: Improve scsi_vpd_inquiry() checks
+    - net: dsa: b53: mmap: add phy ops
+    - s390/ptrace: fix PTRACE_GET_LAST_BREAK error handling
+    - nvme-tcp: fix a possible UAF when failing to allocate an io queue
+    - xen/netback: use same error messages for same errors
+    - platform/x86: gigabyte-wmi: add support for X570S AORUS ELITE
+    - rtmutex: Add acquire semantics for rtmutex lock acquisition slow path
+    - iio: light: tsl2772: fix reading proximity-diodes from device tree
+    - nilfs2: initialize unused bytes in segment summary blocks
+    - memstick: fix memory leak if card device is never registered
+    - kernel/sys.c: fix and improve control flow in __sys_setres[ug]id()
+    - mmc: sdhci_am654: Set HIGH_SPEED_ENA for SDR12 and SDR25
+    - drm/i915: Fix fast wake AUX sync len
+    - mm/khugepaged: check again on anon uffd-wp during isolation
+    - mm: page_alloc: skip regions with hugetlbfs pages when allocating 1G pages
+    - sched/uclamp: Fix fits_capacity() check in feec()
+    - sched/uclamp: Make cpu_overutilized() use util_fits_cpu()
+    - sched/uclamp: Cater for uclamp in find_energy_efficient_cpu()'s early exit
+      condition
+    - sched/fair: Detect capacity inversion
+    - sched/fair: Consider capacity inversion in util_fits_cpu()
+    - sched/uclamp: Fix a uninitialized variable warnings
+    - sched/fair: Fixes for capacity inversion detection
+    - MIPS: Define RUNTIME_DISCARD_EXIT in LD script
+    - docs: futex: Fix kernel-doc references after code split-up preparation
+    - purgatory: fix disabling debug info
+    - fuse: fix attr version comparison in fuse_read_update_size()
+    - fuse: always revalidate rename target dentry
+    - fuse: fix deadlock between atomic O_TRUNC and page invalidation
+    - udp: Call inet6_destroy_sock() in setsockopt(IPV6_ADDRFORM).
+    - tcp/udp: Call inet6_destroy_sock() in IPv6 sk->sk_destruct().
+    - inet6: Remove inet6_destroy_sock() in sk->sk_prot->destroy().
+    - dccp: Call inet6_destroy_sock() via sk->sk_destruct().
+    - sctp: Call inet6_destroy_sock() via sk->sk_destruct().
+    - pwm: meson: Explicitly set .polarity in .get_state()
+    - pwm: iqs620a: Explicitly set .polarity in .get_state()
+    - pwm: hibvt: Explicitly set .polarity in .get_state()
+    - counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
+    - iio: adc: at91-sama5d2_adc: fix an error code in at91_adc_allocate_trigger()
+    - mm/page_alloc: fix potential deadlock on zonelist_update_seq seqlock
+    - ASoC: fsl_asrc_dma: fix potential null-ptr-deref
+    - ASN.1: Fix check for strdup() success
+    - soc: sifive: l2_cache: fix missing iounmap() in error path in
+      sifive_l2_init()
+    - soc: sifive: l2_cache: fix missing free_irq() in error path in
+      sifive_l2_init()
+    - soc: sifive: l2_cache: fix missing of_node_put() in sifive_l2_init()
+    - Linux 5.15.109
+  * Disable hv-kvp-daemon if /dev/vmbus/hv_kvp is not present (LP: #2024900)
+    - [Packaging] disable hv-kvp-daemon if needed
+  * A deadlock issue in scsi rescan task while resuming from S3 (LP: #2018566)
+    - ata: libata-scsi: Avoid deadlock on rescan after device resume
+  * [SRU] Intel Sapphire Rapids HBM support needs CONFIG_NUMA_EMU (LP: #2008745)
+    - [Config] Intel Sapphire Rapids HBM support needs CONFIG_NUMA_EMU
+  * [22.04 FEAT] Enhanced Interpretation for PCI Functions on s390x - kernel
+    part (LP: #1853306)
+    - kvm: use kvfree() in kvm_arch_free_vm()
+    - s390/sclp: add detection of IPL-complete-control facility
+    - s390/pci: use phys_to_virt() for AIBVs/DIBVs
+    - s390/sclp: detect the zPCI load/store interpretation facility
+    - s390/sclp: detect the AISII facility
+    - s390/sclp: detect the AENI facility
+    - s390/sclp: detect the AISI facility
+    - s390/airq: pass more TPI info to airq handlers
+    - s390/airq: allow for airq structure that uses an input vector
+    - s390/pci: externalize the SIC operation controls and routine
+    - s390/pci: stash associated GISA designation
+    - s390/pci: stash dtsm and maxstbl
+    - vfio/pci: introduce CONFIG_VFIO_PCI_ZDEV_KVM
+    - KVM: s390: pci: add basic kvm_zdev structure
+    - KVM: s390: pci: do initial setup for AEN interpretation
+    - KVM: s390: pci: enable host forwarding of Adapter Event Notifications
+    - KVM: s390: mechanism to enable guest zPCI Interpretation
+    - KVM: s390: pci: provide routines for enabling/disabling interrupt forwarding
+    - KVM: s390: pci: add routines to start/stop interpretive execution
+    - vfio-pci/zdev: add open/close device hooks
+    - vfio-pci/zdev: add function handle to clp base capability
+    - vfio-pci/zdev: different maxstbl for interpreted devices
+    - KVM: s390: add KVM_S390_ZPCI_OP to manage guest zPCI devices
+    - MAINTAINERS: additional files related kvm s390 pci passthrough
+    - Documentation: kvm: extend KVM_S390_ZPCI_OP subheading underline
+    - KVM: s390: pci: Hook to access KVM lowlevel from VFIO
+    - KVM: s390: pci: fix plain integer as NULL pointer warnings
+    - KVM: s390: pci: fix GAIT physical vs virtual pointers usage
+    - KVM: s390: pci: register pci hooks without interpretation
+    - [Config] enable VFIO zPCI pass-through for s390x
+  * Undefined Behavior Sanitizer (UBSAN) causes failure to match symbols
+    (LP: #2003374)
+    - [Config] s390x: Re-adding UBSAN to configuration
+  * CVE-2023-35001
+    - netfilter: nf_tables: prevent OOB access in nft_byteorder_eval
+  * CVE-2023-31248
+    - netfilter: nf_tables: do not ignore genmask when looking up chain by id
+  * CVE-2023-3389
+    - io_uring: hold uring mutex around poll removal
+  * CVE-2023-3439
+    - mctp: Add refcounts to mctp_dev
+    - mctp: Allow MCTP on tun devices
+    - mctp: make __mctp_dev_get() take a refcount hold
+    - mctp: defer the kfree of object mdev->addrs
+  * CVE-2023-3390
+    - netfilter: nf_tables: incorrect error path handling with NFT_MSG_NEWRULE
+  * CVE-2023-3141
+    - memstick: r592: Fix UAF bug in r592_remove due to race condition
+  * CVE-2023-3090
+    - ipvlan:Fix out-of-bounds caused by unclear skb->cb
+  * CVE-2022-48502
+    - fs/ntfs3: Check fields while reading
+  * ftrace in ubuntu_kernel_selftests failed with "check if duplicate events are
+    caught" on J-5.15 P9 / J-kvm / L-kvm (LP: #1977827)
+    - SAUCE: selftests/ftrace: Add test dependency
+  * Add microphone support of the front headphone port on P3 Tower
+    (LP: #2023650)
+    - ALSA: hda/realtek: Add Lenovo P3 Tower platform
+  * Add audio support for ThinkPad P1 Gen 6 and Z16 Gen 2 (LP: #2023539)
+    - ALSA: hda/realtek: Add quirks for Lenovo Z13/Z16 Gen2
+    - ALSA: hda/realtek: Add quirk for ThinkPad P1 Gen 6
+  * Resolve synchronous exception on arm64 (LP: #2023311)
+    - arm64: efi: Recover from synchronous exceptions occurring in firmware
+  * Enable Tracing Configs for OSNOISE and TIMERLAT (LP: #2018591)
+    - [Config] Enable OSNOISE_TRACER and TIMERLAT_TRACER configs
+  * Severe NFS performance degradation after LP #2003053 (LP: #2022098)
+    - SAUCE: Make NFS file-access stale cache behaviour opt-in
+  * Encountering an issue with memcpy_fromio causing failed boot of SEV-enabled
+    guest (LP: #2020319)
+    - x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
+  * linux-*: please enable dm-verity kconfigs to allow MoK/db verified root
+    images (LP: #2019040)
+    - [Config] CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG_SECONDARY_KEYRING=y
+  * CVE-2023-2124
+    - xfs: verify buffer contents when we skip log replay
+  * CVE-2023-0597
+    - x86/kasan: Map shadow for percpu pages on demand
+    - x86/mm: Randomize per-cpu entry area
+    - x86/mm: Recompute physical address for every page of per-CPU CEA mapping
+    - x86/mm: Populate KASAN shadow for entire per-CPU range of CPU entry area
+    - x86/mm: Do not shuffle CPU entry areas without KASLR
+  * Jammy update: v5.15.108 upstream stable release (LP: #2023328)
+    - Revert "pinctrl: amd: Disable and mask interrupts on resume"
+    - ALSA: emu10k1: fix capture interrupt handler unlinking
+    - ALSA: hda/sigmatel: add pin overrides for Intel DP45SG motherboard
+    - ALSA: i2c/cs8427: fix iec958 mixer control deactivation
+    - ALSA: firewire-tascam: add missing unwind goto in
+      snd_tscm_stream_start_duplex()
+    - ALSA: emu10k1: don't create old pass-through playback device on Audigy
+    - ALSA: hda/sigmatel: fix S/PDIF out on Intel D*45* motherboards
+    - Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
+    - Bluetooth: Fix race condition in hidp_session_thread
+    - btrfs: print checksum type and implementation at mount time
+    - btrfs: fix fast csum implementation detection
+    - fbmem: Reject FB_ACTIVATE_KD_TEXT from userspace
+    - mtdblock: tolerate corrected bit-flips
+    - mtd: rawnand: meson: fix bitmask for length in command word
+    - mtd: rawnand: stm32_fmc2: remove unsupported EDO mode
+    - mtd: rawnand: stm32_fmc2: use timings.mode instead of checking tRC_min
+    - KVM: arm64: PMU: Restore the guest's EL0 event counting after migration
+    - drm/i915/dsi: fix DSS CTL register offsets for TGL+
+    - clk: sprd: set max_register according to mapping range
+    - RDMA/irdma: Fix memory leak of PBLE objects
+    - RDMA/irdma: Increase iWARP CM default rexmit count
+    - RDMA/irdma: Add ipv4 check to irdma_find_listener()
+    - IB/mlx5: Add support for 400G_8X lane speed
+    - RDMA/cma: Allow UD qp_type to join multicast only
+    - bpf: tcp: Use sock_gen_put instead of sock_put in bpf_iter_tcp
+    - niu: Fix missing unwind goto in niu_alloc_channels()
+    - tcp: restrict net.ipv4.tcp_app_win
+    - drm/armada: Fix a potential double free in an error handling path
+    - qlcnic: check pci_reset_function result
+    - net: qrtr: Fix an uninit variable access bug in qrtr_tx_resume()
+    - sctp: fix a potential overflow in sctp_ifwdtsn_skip
+    - RDMA/core: Fix GID entry ref leak when create_ah fails
+    - udp6: fix potential access to stale information
+    - net: macb: fix a memory corruption in extended buffer descriptor mode
+    - skbuff: Fix a race between coalescing and releasing SKBs
+    - libbpf: Fix single-line struct definition output in btf_dump
+    - ARM: 9290/1: uaccess: Fix KASAN false-positives
+    - power: supply: cros_usbpd: reclassify "default case!" as debug
+    - wifi: mwifiex: mark OF related data as maybe unused
+    - i2c: imx-lpi2c: clean rx/tx buffers upon new message
+    - i2c: hisi: Avoid redundant interrupts
+    - efi: sysfb_efi: Add quirk for Lenovo Yoga Book X91F/L
+    - drm: panel-orientation-quirks: Add quirk for Lenovo Yoga Book X90F
+    - verify_pefile: relax wrapper length check
+    - asymmetric_keys: log on fatal failures in PE/pkcs7
+    - wifi: iwlwifi: mvm: fix mvmtxq->stopped handling
+    - ACPI: resource: Add Medion S17413 to IRQ override quirk
+    - counter: stm32-lptimer-cnt: Provide defines for clock polarities
+    - counter: stm32-timer-cnt: Provide defines for slave mode selection
+    - counter: Internalize sysfs interface code
+    - counter: 104-quad-8: Fix Synapse action reported for Index signals
+    - tracing: Add trace_array_puts() to write into instance
+    - tracing: Have tracing_snapshot_instance_cond() write errors to the
+      appropriate instance
+    - i915/perf: Replace DRM_DEBUG with driver specific drm_dbg call
+    - drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
+    - riscv: add icache flush for nommu sigreturn trampoline
+    - net: sfp: initialize sfp->i2c_block_size at sfp allocation
+    - net: phy: nxp-c45-tja11xx: add remove callback
+    - net: phy: nxp-c45-tja11xx: fix unsigned long multiplication overflow
+    - scsi: ses: Handle enclosure with just a primary component gracefully
+    - x86/PCI: Add quirk for AMD XHCI controller that loses MSI-X state in D3hot
+    - cgroup/cpuset: Wake up cpuset_attach_wq tasks in cpuset_cancel_attach()
+    - mptcp: use mptcp_schedule_work instead of open-coding it
+    - mptcp: stricter state check in mptcp_worker
+    - ubi: Fix failure attaching when vid_hdr offset equals to (sub)page size
+    - ubi: Fix deadlock caused by recursively holding work_sem
+    - powerpc/papr_scm: Update the NUMA distance table for the target node
+    - sched/fair: Move calculate of avg_load to a better location
+    - sched/fair: Fix imbalance overflow
+    - x86/rtc: Remove __init for runtime functions
+    - i2c: ocores: generate stop condition after timeout in polling mode
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S50
+    - nvme-pci: avoid the deepest sleep state on ZHITAI TiPro7000 SSDs
+    - nvme-pci: Crucial P2 has bogus namespace ids
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM610
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM760
+    - nvme-pci: mark Lexar NM760 as IGNORE_DEV_SUBNQN
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD
+    - kexec: turn all kexec_mutex acquisitions into trylocks
+    - panic, kexec: make __crash_kexec() NMI safe
+    - counter: fix docum. build problems after filename change
+    - counter: Add the necessary colons and indents to the comments of
+      counter_compi
+    - nvme-pci: avoid the deepest sleep state on ZHITAI TiPro5000 SSDs
+    - Linux 5.15.108
+  * Jammy update: v5.15.107 upstream stable release (LP: #2023320)
+    - ocfs2: ocfs2_mount_volume does cleanup job before return error
+    - ocfs2: rewrite error handling of ocfs2_fill_super
+    - ocfs2: fix memory leak in ocfs2_mount_volume()
+    - NFSD: Fix sparse warning
+    - NFSD: pass range end to vfs_fsync_range() instead of count
+    - RDMA/irdma: Do not request 2-level PBLEs for CQ alloc
+    - platform/x86: int3472: Split into 2 drivers
+    - [Config] updateconfigs for Intel skl_int3472 driver split
+    - platform/x86: int3472/discrete: Ensure the clk/power enable pins are in
+      output mode
+    - iavf: return errno code instead of status code
+    - iavf/iavf_main: actually log ->src mask when talking about it
+    - serial: 8250_exar: derive nr_ports from PCI ID for Acces I/O cards
+    - serial: exar: Add support for Sealevel 7xxxC serial cards
+    - bpf: hash map, avoid deadlock with suitable hash mask
+    - gpio: GPIO_REGMAP: select REGMAP instead of depending on it
+    - Drivers: vmbus: Check for channel allocation before looking up relids
+    - pwm: cros-ec: Explicitly set .polarity in .get_state()
+    - pwm: sprd: Explicitly set .polarity in .get_state()
+    - KVM: s390: pv: fix external interruption loop not always detected
+    - wifi: mac80211: fix invalid drv_sta_pre_rcu_remove calls for non-uploaded
+      sta
+    - net: qrtr: combine nameservice into main module
+    - [Config] updateconfigs for ns module merger
+    - net: qrtr: Fix a refcount bug in qrtr_recvmsg()
+    - NFSD: Avoid calling OPDESC() with ops->opnum == OP_ILLEGAL
+    - icmp: guard against too small mtu
+    - net: don't let netpoll invoke NAPI if in xmit context
+    - net: dsa: mv88e6xxx: Reset mv88e6393x force WD event bit
+    - sctp: check send stream number after wait_for_sndbuf
+    - net: qrtr: Do not do DEL_SERVER broadcast after DEL_CLIENT
+    - ipv6: Fix an uninit variable access bug in __ip6_make_skb()
+    - platform/x86: think-lmi: Fix memory leak when showing current settings
+    - platform/x86: think-lmi: Fix memory leaks when parsing ThinkStation WMI
+      strings
+    - platform/x86: think-lmi: Clean up display of current_value on Thinkstation
+    - gpio: davinci: Add irq chip flag to skip set wake
+    - net: ethernet: ti: am65-cpsw: Fix mdio cleanup in probe
+    - net: stmmac: fix up RX flow hash indirection table when setting channels
+    - sunrpc: only free unix grouplist after RCU settles
+    - NFSD: callback request does not use correct credential for AUTH_SYS
+    - ice: fix wrong fallback logic for FDIR
+    - ice: Reset FDIR counter in FDIR init stage
+    - ethtool: reset #lanes when lanes is omitted
+    - gve: Secure enough bytes in the first TX desc for all TCP pkts
+    - kbuild: refactor single builds of *.ko
+    - usb: xhci: tegra: fix sleep in atomic call
+    - xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
+    - usb: cdnsp: Fixes error: uninitialized symbol 'len'
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-S
+    - USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs
+    - usb: typec: altmodes/displayport: Fix configure initial pin assignment
+    - USB: serial: option: add Telit FE990 compositions
+    - USB: serial: option: add Quectel RM500U-CN modem
+    - iio: adis16480: select CONFIG_CRC32
+    - iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
+    - iio: dac: cio-dac: Fix max DAC write value check for 12-bit
+    - iio: light: cm32181: Unregister second I2C client if present
+    - tty: serial: sh-sci: Fix transmit end interrupt handler
+    - tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
+    - tty: serial: fsl_lpuart: avoid checking for transfer complete when
+      UARTCTRL_SBK is asserted in lpuart32_tx_empty
+    - nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread()
+    - nilfs2: fix sysfs interface lifetime
+    - dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
+    - ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN
+    - ALSA: hda/realtek: Add quirk for Clevo X370SNW
+    - coresight: etm4x: Do not access TRCIDR1 for identification
+    - coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
+    - iio: adc: ad7791: fix IRQ flags
+    - scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
+    - scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
+    - smb3: allow deferred close timeout to be configurable
+    - smb3: lower default deferred close timeout to address perf regression
+    - cifs: sanitize paths in cifs_update_super_prepath.
+    - perf/core: Fix the same task check in perf_event_set_output
+    - ftrace: Mark get_lock_parent_ip() __always_inline
+    - ftrace: Fix issue that 'direct->addr' not restored in modify_ftrace_direct()
+    - fs: drop peer group ids under namespace lock
+    - can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
+    - can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
+    - tracing: Free error logs of tracing instances
+    - ASoC: hdac_hdmi: use set_stream() instead of set_tdm_slots()
+    - mm: vmalloc: avoid warn_alloc noise caused by fatal signal
+    - drm/panfrost: Fix the panfrost_mmu_map_fault_addr() error path
+    - drm/nouveau/disp: Support more modes by checking with lower bpc
+    - ring-buffer: Fix race while reader and writer are on the same page
+    - mm/swap: fix swap_info_struct race between swapoff and get_swap_pages()
+    - drm/bridge: lt9611: Fix PLL being unable to lock
+    - mm: take a page reference when removing device exclusive entries
+    - kbuild: fix single directory build
+    - ocfs2: fix freeing uninitialized resource on ocfs2_dlm_shutdown
+    - bpftool: Print newline before '}' for struct with padding only fields
+    - Linux 5.15.107
+  * Jammy update: v5.15.106 upstream stable release (LP: #2023233)
+    - fsverity: don't drop pagecache at end of FS_IOC_ENABLE_VERITY
+    - usb: dwc3: gadget: move cmd_endtransfer to extra function
+    - usb: dwc3: gadget: Add 1ms delay after end transfer command without IOC
+    - kernel: kcsan: kcsan_test: build without structleak plugin
+    - kcsan: avoid passing -g for test
+    - ksmbd: don't terminate inactive sessions after a few seconds
+    - bus: imx-weim: fix branch condition evaluates to a garbage value
+    - xfrm: Zero padding when dumping algos and encap
+    - ASoC: codecs: tx-macro: Fix for KASAN: slab-out-of-bounds
+    - md: avoid signed overflow in slot_store()
+    - x86/PVH: obtain VGA console info in Dom0
+    - net: hsr: Don't log netdev_err message on unknown prp dst node
+    - ALSA: asihpi: check pao in control_message()
+    - ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
+    - fbdev: tgafb: Fix potential divide by zero
+    - sched_getaffinity: don't assume 'cpumask_size()' is fully initialized
+    - fbdev: nvidia: Fix potential divide by zero
+    - fbdev: intelfb: Fix potential divide by zero
+    - fbdev: lxfb: Fix potential divide by zero
+    - fbdev: au1200fb: Fix potential divide by zero
+    - tools/power turbostat: Fix /dev/cpu_dma_latency warnings
+    - tools/power turbostat: fix decoding of HWP_STATUS
+    - tracing: Fix wrong return in kprobe_event_gen_test.c
+    - ca8210: Fix unsigned mac_len comparison with zero in ca8210_skb_tx()
+    - mips: bmips: BCM6358: disable RAC flush for TP1
+    - ALSA: usb-audio: Fix recursive locking at XRUN during syncing
+    - platform/x86: think-lmi: add missing type attribute
+    - platform/x86: think-lmi: use correct possible_values delimiters
+    - platform/x86: think-lmi: only display possible_values if available
+    - platform/x86: think-lmi: Add possible_values for ThinkStation
+    - mtd: rawnand: meson: invalidate cache on polling ECC bit
+    - SUNRPC: fix shutdown of NFS TCP client socket
+    - sfc: ef10: don't overwrite offload features at NIC reset
+    - scsi: megaraid_sas: Fix crash after a double completion
+    - scsi: mpt3sas: Don't print sense pool info twice
+    - ptp_qoriq: fix memory leak in probe()
+    - net: dsa: microchip: ksz8863_smi: fix bulk access
+    - r8169: fix RTL8168H and RTL8107E rx crc error
+    - regulator: Handle deferred clk
+    - net/net_failover: fix txq exceeding warning
+    - net: stmmac: don't reject VLANs when IFF_PROMISC is set
+    - drm/i915/tc: Fix the ICL PHY ownership check in TC-cold state
+    - platform/x86/intel/pmc: Alder Lake PCH slp_s0_residency fix
+    - can: bcm: bcm_tx_setup(): fix KMSAN uninit-value in vfs_write
+    - s390/vfio-ap: fix memory leak in vfio_ap device driver
+    - loop: suppress uevents while reconfiguring the device
+    - loop: LOOP_CONFIGURE: send uevents for partitions
+    - net: mvpp2: classifier flow fix fragmentation flags
+    - net: mvpp2: parser fix QinQ
+    - net: mvpp2: parser fix PPPoE
+    - smsc911x: avoid PHY being resumed when interface is not up
+    - ice: add profile conflict check for AVF FDIR
+    - ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
+    - ALSA: ymfpci: Create card with device-managed snd_devm_card_new()
+    - ALSA: ymfpci: Fix BUG_ON in probe function
+    - net: ipa: compute DMA pool size properly
+    - i40e: fix registers dump after run ethtool adapter self test
+    - bnxt_en: Fix reporting of test result in ethtool selftest
+    - bnxt_en: Fix typo in PCI id to device description string mapping
+    - bnxt_en: Add missing 200G link speed reporting
+    - net: dsa: mv88e6xxx: Enable IGMP snooping on user ports only
+    - net: ethernet: mtk_eth_soc: fix flow block refcounting logic
+    - pinctrl: ocelot: Fix alt mode for ocelot
+    - iommu/vt-d: Allow zero SAGAW if second-stage not supported
+    - Input: alps - fix compatibility with -funsigned-char
+    - Input: focaltech - use explicitly signed char type
+    - cifs: prevent infinite recursion in CIFSGetDFSRefer()
+    - cifs: fix DFS traversal oops without CONFIG_CIFS_DFS_UPCALL
+    - Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table
+    - btrfs: fix race between quota disable and quota assign ioctls
+    - btrfs: scan device in non-exclusive mode
+    - zonefs: Always invalidate last cached page on append write
+    - can: j1939: prevent deadlock by moving j1939_sk_errqueue()
+    - xen/netback: don't do grant copy across page boundary
+    - net: phy: dp83869: fix default value for tx-/rx-internal-delay
+    - pinctrl: amd: Disable and mask interrupts on resume
+    - pinctrl: at91-pio4: fix domain name assignment
+    - powerpc: Don't try to copy PPR for task with NULL pt_regs
+    - NFSv4: Fix hangs when recovering open state after a server reboot
+    - ALSA: hda/conexant: Partial revert of a quirk for Lenovo
+    - ALSA: usb-audio: Fix regression on detection of Roland VS-100
+    - ALSA: hda/realtek: Add quirks for some Clevo laptops
+    - ALSA: hda/realtek: Add quirk for Lenovo ZhaoYang CF4620Z
+    - xtensa: fix KASAN report for show_stack
+    - rcu: Fix rcu_torture_read ftrace event
+    - drm/etnaviv: fix reference leak when mmaping imported buffer
+    - drm/amd/display: Add DSC Support for Synaptics Cascaded MST Hub
+    - KVM: arm64: Disable interrupts while walking userspace PTs
+    - KVM: VMX: Move preemption timer <=> hrtimer dance to common x86
+    - KVM: x86: Inject #GP on x2APIC WRMSR that sets reserved bits 63:32
+    - KVM: x86: Purge "highest ISR" cache when updating APICv state
+    - zonefs: Fix error message in zonefs_file_dio_append()
+    - selftests/bpf: Test btf dump for struct with padding only fields
+    - libbpf: Fix BTF-to-C converter's padding logic
+    - selftests/bpf: Add few corner cases to test padding handling of btf_dump
+    - libbpf: Fix btf_dump's packed struct determination
+    - hsr: ratelimit only when errors are printed
+    - x86/PVH: avoid 32-bit build warning when obtaining VGA console info
+    - Linux 5.15.106
+  * Jammy update: v5.15.105 upstream stable release (LP: #2023230)
+    - interconnect: qcom: osm-l3: fix icc_onecell_data allocation
+    - perf/core: Fix perf_output_begin parameter is incorrectly invoked in
+      perf_event_bpf_output
+    - perf: fix perf_event_context->time
+    - tracing/hwlat: Replace sched_setaffinity with set_cpus_allowed_ptr
+    - serial: fsl_lpuart: Fix comment typo
+    - tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
+    - tty: serial: fsl_lpuart: fix race on RX DMA shutdown
+    - serial: 8250: SERIAL_8250_ASPEED_VUART should depend on ARCH_ASPEED
+    - [Config] updateconfigs for SERIAL_8250_ASPEED_VUART
+    - serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
+    - kthread: add the helper function kthread_run_on_cpu()
+    - trace/hwlat: make use of the helper function kthread_run_on_cpu()
+    - trace/hwlat: Do not start per-cpu thread if it is already running
+    - net: tls: fix possible race condition between do_tls_getsockopt_conf() and
+      do_tls_setsockopt_conf()
+    - power: supply: bq24190_charger: using pm_runtime_resume_and_get instead of
+      pm_runtime_get_sync
+    - power: supply: bq24190: Fix use after free bug in bq24190_remove due to race
+      condition
+    - power: supply: da9150: Fix use after free bug in da9150_charger_remove due
+      to race condition
+    - ARM: dts: imx6sll: e60k02: fix usbotg1 pinctrl
+    - ARM: dts: imx6sl: tolino-shine2hd: fix usbotg1 pinctrl
+    - arm64: dts: imx8mn: specify #sound-dai-cells for SAI nodes
+    - xsk: Add missing overflow check in xdp_umem_reg
+    - iavf: fix inverted Rx hash condition leading to disabled hash
+    - iavf: fix non-tunneled IPv6 UDP packet type and hashing
+    - intel/igbvf: free irq on the error path in igbvf_request_msix()
+    - igbvf: Regard vf reset nack as success
+    - igc: fix the validation logic for taprio's gate list
+    - i2c: imx-lpi2c: check only for enabled interrupt flags
+    - i2c: hisi: Only use the completion interrupt to finish the transfer
+    - scsi: scsi_dh_alua: Fix memleak for 'qdata' in alua_activate()
+    - net: dsa: b53: mmap: fix device tree support
+    - net: usb: smsc95xx: Limit packet length to skb->len
+    - qed/qed_sriov: guard against NULL derefs from qed_iov_get_vf_info
+    - net: phy: Ensure state transitions are processed from phy_stop()
+    - net: mdio: fix owner field for mdio buses registered using device-tree
+    - net: mdio: fix owner field for mdio buses registered using ACPI
+    - drm/i915/gt: perform uc late init after probe error injection
+    - net: qcom/emac: Fix use after free bug in emac_remove due to race condition
+    - net/ps3_gelic_net: Fix RX sk_buff length
+    - net/ps3_gelic_net: Use dma_mapping_error
+    - octeontx2-vf: Add missing free for alloc_percpu
+    - bootconfig: Fix testcase to increase max node
+    - keys: Do not cache key in task struct if key is requested from kernel thread
+    - iavf: fix hang on reboot with ice
+    - i40e: fix flow director packet filter programming
+    - bpf: Adjust insufficient default bpf_jit_limit
+    - net/mlx5e: Set uplink rep as NETNS_LOCAL
+    - net/mlx5: Fix steering rules cleanup
+    - net/mlx5: Read the TC mapping of all priorities on ETS query
+    - net/mlx5: E-Switch, Fix an Oops in error handling code
+    - net: dsa: tag_brcm: legacy: fix daisy-chained switches
+    - atm: idt77252: fix kmemleak when rmmod idt77252
+    - erspan: do not use skb_mac_header() in ndo_start_xmit()
+    - net/sonic: use dma_mapping_error() for error check
+    - nvme-tcp: fix nvme_tcp_term_pdu to match spec
+    - hvc/xen: prevent concurrent accesses to the shared ring
+    - ksmbd: add low bound validation to FSCTL_SET_ZERO_DATA
+    - ksmbd: add low bound validation to FSCTL_QUERY_ALLOCATED_RANGES
+    - ksmbd: fix possible refcount leak in smb2_open()
+    - gve: Cache link_speed value from device
+    - net: dsa: mt7530: move enabling disabling core clock to mt7530_pll_setup()
+    - net: dsa: mt7530: move lowering TRGMII driving to mt7530_setup()
+    - net: dsa: mt7530: move setting ssc_delta to PHY_INTERFACE_MODE_TRGMII case
+    - net: mdio: thunder: Add missing fwnode_handle_put()
+    - Bluetooth: btqcomsmd: Fix command timeout after setting BD address
+    - Bluetooth: L2CAP: Fix responding with wrong PDU type
+    - platform/chrome: cros_ec_chardev: fix kernel data leak from ioctl
+    - thread_info: Add helpers to snapshot thread flags
+    - entry: Snapshot thread flags
+    - entry/rcu: Check TIF_RESCHED _after_ delayed RCU wake-up
+    - hwmon: fix potential sensor registration fail if of_node is missing
+    - hwmon (it87): Fix voltage scaling for chips with 10.9mV ADCs
+    - scsi: qla2xxx: Synchronize the IOCB count to be in order
+    - scsi: qla2xxx: Perform lockless command completion in abort path
+    - uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS583Gen 2
+    - thunderbolt: Use scale field when allocating USB3 bandwidth
+    - thunderbolt: Call tb_check_quirks() after initializing adapters
+    - thunderbolt: Disable interrupt auto clear for rings
+    - thunderbolt: Add missing UNSET_INBOUND_SBTX for retimer access
+    - thunderbolt: Use const qualifier for `ring_interrupt_index`
+    - thunderbolt: Rename shadowed variables bit to interrupt_bit and
+      auto_clear_bit
+    - ACPI: x86: utils: Add Cezanne to the list for forcing StorageD3Enable
+    - riscv: Bump COMMAND_LINE_SIZE value to 1024
+    - drm/cirrus: NULL-check pipe->plane.state->fb in cirrus_pipe_update()
+    - HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
+    - ca8210: fix mac_len negative array access
+    - HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
+    - m68k: Only force 030 bus error if PC not in exception table
+    - selftests/bpf: check that modifier resolves after pointer
+    - scsi: target: iscsi: Fix an error message in iscsi_check_key()
+    - scsi: hisi_sas: Check devm_add_action() return value
+    - scsi: ufs: core: Add soft dependency on governor_simpleondemand
+    - scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read()
+    - scsi: lpfc: Avoid usage of list iterator variable after loop
+    - scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
+    - net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
+    - net: usb: qmi_wwan: add Telit 0x1080 composition
+    - sh: sanitize the flags on sigreturn
+    - net/sched: act_mirred: better wording on protection against excessive stack
+      growth
+    - act_mirred: use the backlog for nested calls to mirred ingress
+    - cifs: empty interface list when server doesn't support query interfaces
+    - cifs: print session id while listing open files
+    - scsi: core: Add BLIST_SKIP_VPD_PAGES for SKhynix H28U74301AMR
+    - usb: dwc2: fix a devres leak in hw_enable upon suspend resume
+    - usb: gadget: u_audio: don't let userspace block driver unbind
+    - efi: sysfb_efi: Fix DMI quirks not working for simpledrm
+    - mm/slab: Fix undefined init_cache_node_node() for NUMA and !SMP
+    - fscrypt: destroy keyring after security_sb_delete()
+    - fsverity: Remove WQ_UNBOUND from fsverity read workqueue
+    - lockd: set file_lock start and end when decoding nlm4 testargs
+    - arm64: dts: imx8mm-nitrogen-r2: fix WM8960 clock name
+    - igb: revert rtnl_lock() that causes deadlock
+    - dm thin: fix deadlock when swapping to thin device
+    - usb: typec: tcpm: fix warning when handle discover_identity message
+    - usb: cdns3: Fix issue with using incorrect PCI device function
+    - usb: cdnsp: Fixes issue with redundant Status Stage
+    - usb: cdnsp: changes PCI Device ID to fix conflict with CNDS3 driver
+    - usb: chipdea: core: fix return -EINVAL if request role is the same with
+      current role
+    - usb: chipidea: core: fix possible concurrent when switch role
+    - usb: ucsi: Fix NULL pointer deref in ucsi_connector_change()
+    - kfence: avoid passing -g for test
+    - KVM: x86: hyper-v: Avoid calling kvm_make_vcpus_request_mask() with
+      vcpu_mask==NULL
+    - ksmbd: set FILE_NAMED_STREAMS attribute in FS_ATTRIBUTE_INFORMATION
+    - ksmbd: return STATUS_NOT_SUPPORTED on unsupported smb2.0 dialect
+    - ksmbd: return unsupported error on smb1 mount
+    - wifi: mac80211: fix qos on mesh interfaces
+    - nilfs2: fix kernel-infoleak in nilfs_ioctl_wrap_copy()
+    - drm/bridge: lt8912b: return EPROBE_DEFER if bridge is not found
+    - drm/meson: fix missing component unbind on bind errors
+    - drm/amdgpu/nv: Apply ASPM quirk on Intel ADL + AMD Navi
+    - drm/i915/active: Fix missing debug object activation
+    - drm/i915: Preserve crtc_state->inherited during state clearing
+    - riscv: mm: Fix incorrect ASID argument when flushing TLB
+    - riscv: Handle zicsr/zifencei issues between clang and binutils
+    - tee: amdtee: fix race condition in amdtee_open_session
+    - firmware: arm_scmi: Fix device node validation for mailbox transport
+    - i2c: xgene-slimpro: Fix out-of-bounds bug in xgene_slimpro_i2c_xfer()
+    - dm stats: check for and propagate alloc_percpu failure
+    - dm crypt: add cond_resched() to dmcrypt_write()
+    - dm crypt: avoid accessing uninitialized tasklet
+    - sched/fair: sanitize vruntime of entity being placed
+    - sched/fair: Sanitize vruntime of entity being migrated
+    - mm: kfence: fix using kfence_metadata without initialization in
+      show_object()
+    - ocfs2: fix data corruption after failed write
+    - Linux 5.15.105
+  * Jammy update: v5.15.104 upstream stable release (LP: #2023225)
+    - xfrm: Allow transport-mode states with AF_UNSPEC selector
+    - drm/panfrost: Don't sync rpm suspension after mmu flushing
+    - cifs: Move the in_send statistic to __smb_send_rqst()
+    - drm/meson: fix 1px pink line on GXM when scaling video overlay
+    - clk: HI655X: select REGMAP instead of depending on it
+    - docs: Correct missing "d_" prefix for dentry_operations member
+      d_weak_revalidate
+    - scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add()
+    - ALSA: hda: Match only Intel devices with CONTROLLER_IN_GPU()
+    - netfilter: nft_nat: correct length for loading protocol registers
+    - netfilter: nft_masq: correct length for loading protocol registers
+    - netfilter: nft_redir: correct length for loading protocol registers
+    - netfilter: nft_redir: correct value of inet type `.maxattrs`
+    - scsi: core: Fix a procfs host directory removal regression
+    - tcp: tcp_make_synack() can be called from process context
+    - nfc: pn533: initialize struct pn533_out_arg properly
+    - ipvlan: Make skb->skb_iif track skb->dev for l3s mode
+    - i40e: Fix kernel crash during reboot when adapter is in recovery mode
+    - vdpa_sim: not reset state in vdpasim_queue_ready
+    - vdpa_sim: set last_used_idx as last_avail_idx in vdpasim_queue_ready
+    - PCI: s390: Fix use-after-free of PCI resources with per-function hotplug
+    - drm/i915/display: Workaround cursor left overs with PSR2 selective fetch
+      enabled
+    - drm/i915/display/psr: Use drm damage helpers to calculate plane damaged area
+    - drm/i915/display: clean up comments
+    - drm/i915/psr: Use calculated io and fast wake lines
+    - net/smc: fix NULL sndbuf_desc in smc_cdc_tx_handler()
+    - qed/qed_dev: guard against a possible division by zero
+    - net: dsa: mt7530: remove now incorrect comment regarding port 5
+    - net: dsa: mt7530: set PLL frequency and trgmii only when trgmii is used
+    - loop: Fix use-after-free issues
+    - net: tunnels: annotate lockless accesses to dev->needed_headroom
+    - net: phy: smsc: bail out in lan87xx_read_status if genphy_read_status fails
+    - nfc: st-nci: Fix use after free bug in ndlc_remove due to race condition
+    - net/smc: fix deadlock triggered by cancel_delayed_work_syn()
+    - net: usb: smsc75xx: Limit packet length to skb->len
+    - drm/bridge: Fix returned array size name for atomic_get_input_bus_fmts kdoc
+    - block: null_blk: Fix handling of fake timeout request
+    - nvme: fix handling single range discard request
+    - nvmet: avoid potential UAF in nvmet_req_complete()
+    - block: sunvdc: add check for mdesc_grab() returning NULL
+    - ice: xsk: disable txq irq before flushing hw
+    - net: dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
+    - ravb: avoid PHY being resumed when interface is not up
+    - sh_eth: avoid PHY being resumed when interface is not up
+    - ipv4: Fix incorrect table ID in IOCTL path
+    - net: usb: smsc75xx: Move packet length check to prevent kernel panic in
+      skb_pull
+    - net/iucv: Fix size of interrupt data
+    - qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
+    - ethernet: sun: add check for the mdesc_grab()
+    - bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
+    - bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
+    - hwmon: (adt7475) Display smoothing attributes in correct order
+    - hwmon: (adt7475) Fix masking of hysteresis registers
+    - hwmon: (xgene) Fix use after free bug in xgene_hwmon_remove due to race
+      condition
+    - hwmon: (ina3221) return prober error code
+    - hwmon: (ucd90320) Add minimum delay between bus accesses
+    - hwmon: tmp512: drop of_match_ptr for ID table
+    - kconfig: Update config changed flag before calling callback
+    - hwmon: (adm1266) Set `can_sleep` flag for GPIO chip
+    - hwmon: (ltc2992) Set `can_sleep` flag for GPIO chip
+    - media: m5mols: fix off-by-one loop termination error
+    - mmc: atmel-mci: fix race between stop command and start of next command
+    - jffs2: correct logic when creating a hole in jffs2_write_begin
+    - ext4: fail ext4_iget if special inode unallocated
+    - ext4: update s_journal_inum if it changes after journal replay
+    - ext4: fix task hung in ext4_xattr_delete_inode
+    - drm/amdkfd: Fix an illegal memory access
+    - net/9p: fix bug in client create for .L
+    - sh: intc: Avoid spurious sizeof-pointer-div warning
+    - drm/amd/display: fix shift-out-of-bounds in CalculateVMAndRowBytes
+    - ext4: fix possible double unlock when moving a directory
+    - tty: serial: fsl_lpuart: skip waiting for transmission complete when
+      UARTCTRL_SBK is asserted
+    - serial: 8250_em: Fix UART port type
+    - serial: 8250_fsl: fix handle_irq locking
+    - firmware: xilinx: don't make a sleepable memory allocation from an atomic
+      context
+    - s390/ipl: add missing intersection check to ipl_report handling
+    - interconnect: fix mem leak when freeing nodes
+    - interconnect: exynos: fix node leak in probe PM QoS error path
+    - tracing: Make splice_read available again
+    - tracing: Check field value in hist_field_name()
+    - tracing: Make tracepoint lockdep check actually test something
+    - cifs: Fix smb2_set_path_size()
+    - ALSA: hda: intel-dsp-config: add MTL PCI id
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro
+    - Revert "riscv: mm: notify remote harts about mmu cache updates"
+    - riscv: asid: Fixup stale TLB entry cause application crash
+    - drm/shmem-helper: Remove another errant put in error path
+    - drm/sun4i: fix missing component unbind on bind errors
+    - drm/amd/pm: Fix sienna cichlid incorrect OD volage after resume
+    - mptcp: fix possible deadlock in subflow_error_report
+    - mptcp: add ro_after_init for tcp{,v6}_prot_override
+    - mptcp: avoid setting TCP_CLOSE state twice
+    - mptcp: fix lockdep false positive in mptcp_pm_nl_create_listen_socket()
+    - ftrace: Fix invalid address access in lookup_rec() when index is 0
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV3000
+    - mm/userfaultfd: propagate uffd-wp bit when PTE-mapping the huge zeropage
+    - mmc: sdhci_am654: lower power-on failed message severity
+    - fbdev: stifb: Provide valid pixelclock and add fb_check_var() checks
+    - trace/hwlat: Do not wipe the contents of per-cpu thread data
+    - net: phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit
+    - cpuidle: psci: Iterate backwards over list in psci_pd_remove()
+    - x86/mce: Make sure logged MCEs are processed after sysfs update
+    - x86/mm: Fix use of uninitialized buffer in sme_enable()
+    - x86/resctrl: Clear staged_config[] before and after it is used
+    - drm/i915: Don't use stolen memory for ring buffers with LLC
+    - drm/i915/active: Fix misuse of non-idle barriers as fence trackers
+    - io_uring: avoid null-ptr-deref in io_arm_poll_handler
+    - PCI: Unify delay handling for reset and resume
+    - PCI/DPC: Await readiness of secondary bus after reset
+    - HID: core: Provide new max_buffer_size attribute to over-ride the default
+    - HID: uhid: Over-ride the default maximum data buffer value with our own
+    - perf: Fix check before add_event_to_groups() in perf_group_detach()
+    - Linux 5.15.104
+  * Jammy update: v5.15.103 upstream stable release (LP: #2023224)
+    - fs: prevent out-of-bounds array speculation when closing a file descriptor
+    - btrfs: fix percent calculation for bg reclaim message
+    - perf inject: Fix --buildid-all not to eat up MMAP2
+    - fork: allow CLONE_NEWTIME in clone3 flags
+    - x86/CPU/AMD: Disable XSAVES on AMD family 0x17
+    - drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc15
+    - drm/connector: print max_requested_bpc in state debugfs
+    - staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
+    - ext4: fix cgroup writeback accounting with fs-layer encryption
+    - ext4: fix RENAME_WHITEOUT handling for inline directories
+    - ext4: fix another off-by-one fsmap error on 1k block filesystems
+    - ext4: move where set the MAY_INLINE_DATA flag is set
+    - ext4: fix WARNING in ext4_update_inline_data
+    - ext4: zero i_disksize when initializing the bootloader inode
+    - nfc: change order inside nfc_se_io error path
+    - KVM: Optimize kvm_make_vcpus_request_mask() a bit
+    - KVM: Pre-allocate cpumasks for kvm_make_all_cpus_request_except()
+    - KVM: Register /dev/kvm as the _very_ last thing during initialization
+    - KVM: SVM: Don't rewrite guest ICR on AVIC IPI virtualization failure
+    - KVM: SVM: Process ICR on AVIC IPI delivery failure due to invalid target
+    - fs: dlm: fix log of lowcomms vs midcomms
+    - fs: dlm: add midcomms init/start functions
+    - fs: dlm: start midcomms before scand
+    - udf: Fix off-by-one error when discarding preallocation
+    - f2fs: avoid down_write on nat_tree_lock during checkpoint
+    - f2fs: do not bother checkpoint by f2fs_get_node_info
+    - f2fs: retry to update the inode page given data corruption
+    - ipmi:ssif: Increase the message retry time
+    - ipmi:ssif: Add a timer between request retries
+    - irqdomain: Refactor __irq_domain_alloc_irqs()
+    - iommu/vt-d: Fix PASID directory pointer coherency
+    - block/brd: add error handling support for add_disk()
+    - brd: mark as nowait compatible
+    - arm64: efi: Make efi_rt_lock a raw_spinlock
+    - RISC-V: Avoid dereferening NULL regs in die()
+    - riscv: Avoid enabling interrupts in die()
+    - riscv: Add header include guards to insn.h
+    - scsi: core: Remove the /proc/scsi/${proc_name} directory earlier
+    - regulator: Flag uncontrollable regulators as always_on
+    - regulator: core: Fix off-on-delay-us for always-on/boot-on regulators
+    - regulator: core: Use ktime_get_boottime() to determine how long a regulator
+      was off
+    - ext4: Fix possible corruption when moving a directory
+    - drm/nouveau/kms/nv50-: remove unused functions
+    - drm/nouveau/kms/nv50: fix nv50_wndw_new_ prototype
+    - drm/msm: Fix potential invalid ptr free
+    - drm/msm/a5xx: fix setting of the CP_PREEMPT_ENABLE_LOCAL register
+    - drm/msm/a5xx: fix highest bank bit for a530
+    - drm/msm/a5xx: fix the emptyness check in the preempt code
+    - drm/msm/a5xx: fix context faults during ring switch
+    - bgmac: fix *initial* chip reset to support BCM5358
+    - nfc: fdp: add null check of devm_kmalloc_array in
+      fdp_nci_i2c_read_device_properties
+    - powerpc: dts: t1040rdb: fix compatible string for Rev A boards
+    - ila: do not generate empty messages in ila_xlat_nl_cmd_get_mapping()
+    - selftests: nft_nat: ensuring the listening side is up before starting the
+      client
+    - perf stat: Fix counting when initial delay configured
+    - net: lan78xx: fix accessing the LAN7800's internal phy specific registers
+      from the MAC driver
+    - net: caif: Fix use-after-free in cfusbl_device_notify()
+    - ice: copy last block omitted in ice_get_module_eeprom()
+    - bpf, sockmap: Fix an infinite loop error when len is 0 in
+      tcp_bpf_recvmsg_parser()
+    - drm/msm/dpu: fix len of sc7180 ctl blocks
+    - net: stmmac: add to set device wake up flag when stmmac init phy
+    - net: phylib: get rid of unnecessary locking
+    - bnxt_en: Avoid order-5 memory allocation for TPA data
+    - netfilter: tproxy: fix deadlock due to missing BH disable
+    - btf: fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
+    - net: phy: smsc: Cache interrupt mask
+    - net: phy: smsc: fix link up detection in forced irq mode
+    - net: ethernet: mtk_eth_soc: fix RX data corruption issue
+    - scsi: megaraid_sas: Update max supported LD IDs to 240
+    - platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
+    - net/smc: fix fallback failed while sendmsg with fastopen
+    - octeontx2-af: Unlock contexts in the queue context cache in case of fault
+      detection
+    - SUNRPC: Fix a server shutdown leak
+    - net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
+    - af_unix: Remove unnecessary brackets around CONFIG_AF_UNIX_OOB.
+    - af_unix: fix struct pid leaks in OOB support
+    - riscv: Use READ_ONCE_NOCHECK in imprecise unwinding stack mode
+    - s390/ftrace: remove dead code
+    - RISC-V: Don't check text_mutex during stop_machine
+    - ext4: Fix deadlock during directory rename
+    - irqdomain: Fix mapping-creation race
+    - nbd: use the correct block_device in nbd_bdev_reset
+    - iommu/amd: Add PCI segment support for ivrs_[ioapic/hpet/acpihid] commands
+    - iommu/amd: Fix ill-formed ivrs_ioapic, ivrs_hpet and ivrs_acpihid options
+    - iommu/amd: Add a length limitation for the ivrs_acpihid command-line
+      parameter
+    - staging: rtl8723bs: clean up comparsions to NULL
+    - Staging: rtl8723bs: Placing opening { braces in previous line
+    - staging: rtl8723bs: fix placement of braces
+    - staging: rtl8723bs: Fix key-store index handling
+    - watch_queue: fix IOC_WATCH_QUEUE_SET_SIZE alloc error paths
+    - tpm/eventlog: Don't abort tpm_read_log on faulty ACPI address
+    - xfs: use setattr_copy to set vfs inode attributes
+    - xfs: remove XFS_PREALLOC_SYNC
+    - xfs: fallocate() should call file_modified()
+    - xfs: set prealloc flag in xfs_alloc_file_space()
+    - fs: add mode_strip_sgid() helper
+    - fs: move S_ISGID stripping into the vfs_*() helpers
+    - attr: add in_group_or_capable()
+    - fs: move should_remove_suid()
+    - attr: add setattr_should_drop_sgid()
+    - attr: use consistent sgid stripping checks
+    - fs: use consistent setgid checks in is_sxid()
+    - MIPS: Fix a compilation issue
+    - powerpc/iommu: fix memory leak with using debugfs_lookup()
+    - powerpc/kcsan: Exclude udelay to prevent recursive instrumentation
+    - alpha: fix R_ALPHA_LITERAL reloc for large modules
+    - macintosh: windfarm: Use unsigned type for 1-bit bitfields
+    - PCI: Add SolidRun vendor ID
+    - scripts: handle BrokenPipeError for python scripts
+    - media: ov5640: Fix analogue gain control
+    - media: rc: gpio-ir-recv: add remove function
+    - filelocks: use mount idmapping for setlease permission check
+    - ext4: refactor ext4_free_blocks() to pull out ext4_mb_clear_bb()
+    - ext4: add ext4_sb_block_valid() refactored out of ext4_inode_block_valid()
+    - ext4: add strict range checks while freeing blocks
+    - ext4: block range must be validated before use in ext4_mb_clear_bb()
+    - arch: fix broken BuildID for arm64 and riscv
+    - powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT
+    - powerpc/vmlinux.lds: Don't discard .rela* for relocatable builds
+    - s390: define RUNTIME_DISCARD_EXIT to fix link error with GNU ld < 2.36
+    - sh: define RUNTIME_DISCARD_EXIT
+    - tools build: Add feature test for init_disassemble_info API changes
+    - tools include: add dis-asm-compat.h to handle version differences
+    - tools perf: Fix compilation error with new binutils
+    - tools bpf_jit_disasm: Fix compilation error with new binutils
+    - tools bpftool: Fix compilation error with new binutils
+    - KVM: fix memoryleak in kvm_init()
+    - xfs: remove xfs_setattr_time() declaration
+    - UML: define RUNTIME_DISCARD_EXIT
+    - fs: hold writers when changing mount's idmapping
+    - KVM: nVMX: Don't use Enlightened MSR Bitmap for L3
+    - KVM: VMX: Introduce vmx_msr_bitmap_l01_changed() helper
+    - KVM: VMX: Fix crash due to uninitialized current_vmcs
+    - Makefile: use -gdwarf-{4|5} for assembler for DEBUG_INFO_DWARF{4|5}
+    - Linux 5.15.103
+  * Jammy update: v5.15.102 upstream stable release (LP: #2020393)
+    - staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
+    - staging: rtl8192e: Remove call_usermodehelper starting RadioPower.sh
+    - Linux 5.15.102
+  * Jammy update: v5.15.101 upstream stable release (LP: #2020391)
+    - Linux 5.15.101
+  * Jammy update: v5.15.100 upstream stable release (LP: #2020387)
+    - auxdisplay: hd44780: Fix potential memory leak in hd44780_remove()
+    - fs/jfs: fix shift exponent db_agl2size negative
+    - objtool: Fix memory leak in create_static_call_sections()
+    - pwm: sifive: Reduce time the controller lock is held
+    - pwm: sifive: Always let the first pwm_apply_state succeed
+    - pwm: stm32-lp: fix the check on arr and cmp registers update
+    - f2fs: use memcpy_{to,from}_page() where possible
+    - fs: f2fs: initialize fsdata in pagecache_write()
+    - f2fs: allow set compression option of files without blocks
+    - um: vector: Fix memory leak in vector_config
+    - ubi: ensure that VID header offset + VID header size <= alloc, size
+    - ubifs: Fix build errors as symbol undefined
+    - ubifs: Rectify space budget for ubifs_symlink() if symlink is encrypted
+    - ubifs: Rectify space budget for ubifs_xrename()
+    - ubifs: Fix wrong dirty space budget for dirty inode
+    - ubifs: do_rename: Fix wrong space budget when target inode's nlink > 1
+    - ubifs: Reserve one leb for each journal head while doing budget
+    - ubi: Fix use-after-free when volume resizing failed
+    - ubi: Fix unreferenced object reported by kmemleak in ubi_resize_volume()
+    - ubifs: Fix memory leak in alloc_wbufs()
+    - ubi: Fix possible null-ptr-deref in ubi_free_volume()
+    - ubifs: Re-statistic cleaned znode count if commit failed
+    - ubifs: ubifs_writepage: Mark page dirty after writing inode failed
+    - ubi: fastmap: Fix missed fm_anchor PEB in wear-leveling after disabling
+      fastmap
+    - ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
+    - ubi: ubi_wl_put_peb: Fix infinite loop when wear-leveling work failed
+    - f2fs: fix to avoid potential memory corruption in __update_iostat_latency()
+    - ext4: use ext4_fc_tl_mem in fast-commit replay path
+    - netfilter: nf_tables: allow to fetch set elements when table has an owner
+    - x86: um: vdso: Add '%rcx' and '%r11' to the syscall clobber list
+    - um: virtio_uml: free command if adding to virtqueue failed
+    - um: virtio_uml: mark device as unregistered when breaking it
+    - um: virtio_uml: move device breaking into workqueue
+    - um: virt-pci: properly remove PCI device from bus
+    - watchdog: at91sam9_wdt: use devm_request_irq to avoid missing free_irq() in
+      error path
+    - watchdog: Fix kmemleak in watchdog_cdev_register
+    - watchdog: pcwd_usb: Fix attempting to access uninitialized memory
+    - watchdog: sbsa_wdog: Make sure the timeout programming is within the limits
+    - netfilter: ctnetlink: fix possible refcount leak in
+      ctnetlink_create_conntrack()
+    - netfilter: ebtables: fix table blob use-after-free
+    - netfilter: x_tables: fix percpu counter block leak on error path when
+      creating new netns
+    - ipv6: Add lwtunnel encap size of all siblings in nexthop calculation
+    - sctp: add a refcnt in sctp_stream_priorities to avoid a nested loop
+    - octeontx2-pf: Use correct struct reference in test condition
+    - net: fix __dev_kfree_skb_any() vs drop monitor
+    - 9p/xen: fix version parsing
+    - 9p/xen: fix connection sequence
+    - 9p/rdma: unmap receive dma buffer in rdma_request()/post_recv()
+    - net/mlx5e: Verify flow_source cap before using it
+    - net/mlx5: Geneve, Fix handling of Geneve object id as error code
+    - nfc: fix memory leak of se_io context in nfc_genl_se_io
+    - net/sched: transition act_pedit to rcu and percpu stats
+    - net/sched: act_pedit: fix action bind logic
+    - net/sched: act_mpls: fix action bind logic
+    - net/sched: act_sample: fix action bind logic
+    - ARM: dts: spear320-hmi: correct STMPE GPIO compatible
+    - tcp: tcp_check_req() can be called from process context
+    - vc_screen: modify vcs_size() handling in vcs_read()
+    - rtc: sun6i: Always export the internal oscillator
+    - genirq: Refactor accessors to use irq_data_get_affinity_mask
+    - genirq: Add and use an irq_data_update_affinity helper
+    - scsi: ipr: Work around fortify-string warning
+    - rtc: allow rtc_read_alarm without read_alarm callback
+    - loop: loop_set_status_from_info() check before assignment
+    - ASoC: adau7118: don't disable regulators on device unbind
+    - ASoC: zl38060: Remove spurious gpiolib select
+    - ASoC: zl38060 add gpiolib dependency
+    - ASoC: mediatek: mt8195: add missing initialization
+    - thermal: intel: quark_dts: fix error pointer dereference
+    - thermal: intel: BXT_PMIC: select REGMAP instead of depending on it
+    - tracing: Add NULL checks for buffer in ring_buffer_free_read_page()
+    - kernel/printk/index.c: fix memory leak with using debugfs_lookup()
+    - firmware/efi sysfb_efi: Add quirk for Lenovo IdeaPad Duet 3
+    - bootconfig: Increase max nodes of bootconfig from 1024 to 8192 for DCC
+      support
+    - mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
+    - IB/hfi1: Update RMT size calculation
+    - iommu/amd: Fix error handling for pdev_pri_ats_enable()
+    - media: uvcvideo: Remove format descriptions
+    - media: uvcvideo: Handle cameras with invalid descriptors
+    - media: uvcvideo: Handle errors from calls to usb_string
+    - media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910
+    - media: uvcvideo: Silence memcpy() run-time false positive warnings
+    - USB: fix memory leak with using debugfs_lookup()
+    - staging: emxx_udc: Add checks for dma_alloc_coherent()
+    - tty: fix out-of-bounds access in tty_driver_lookup_tty()
+    - tty: serial: fsl_lpuart: disable the CTS when send break signal
+    - serial: sc16is7xx: setup GPIO controller later in probe
+    - mei: bus-fixup:upon error print return values of send and receive
+    - tools/iio/iio_utils:fix memory leak
+    - iio: accel: mma9551_core: Prevent uninitialized variable in
+      mma9551_read_status_word()
+    - iio: accel: mma9551_core: Prevent uninitialized variable in
+      mma9551_read_config_word()
+    - soundwire: bus_type: Avoid lockdep assert in sdw_drv_probe()
+    - PCI: loongson: Prevent LS7A MRRS increases
+    - USB: dwc3: fix memory leak with using debugfs_lookup()
+    - USB: chipidea: fix memory leak with using debugfs_lookup()
+    - USB: uhci: fix memory leak with using debugfs_lookup()
+    - USB: sl811: fix memory leak with using debugfs_lookup()
+    - USB: fotg210: fix memory leak with using debugfs_lookup()
+    - USB: isp116x: fix memory leak with using debugfs_lookup()
+    - USB: isp1362: fix memory leak with using debugfs_lookup()
+    - USB: gadget: gr_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: bcm63xx_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: lpc32xx_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: pxa25x_udc: fix memory leak with using debugfs_lookup()
+    - USB: gadget: pxa27x_udc: fix memory leak with using debugfs_lookup()
+    - usb: host: xhci: mvebu: Iterate over array indexes instead of using pointer
+      math
+    - USB: ene_usb6250: Allocate enough memory for full object
+    - usb: uvc: Enumerate valid values for color matching
+    - usb: gadget: uvc: Make bSourceID read/write
+    - PCI: Align extra resources for hotplug bridges properly
+    - PCI: Take other bus devices into account when distributing resources
+    - tty: pcn_uart: fix memory leak with using debugfs_lookup()
+    - misc: vmw_balloon: fix memory leak with using debugfs_lookup()
+    - drivers: base: component: fix memory leak with using debugfs_lookup()
+    - drivers: base: dd: fix memory leak with using debugfs_lookup()
+    - kernel/fail_function: fix memory leak with using debugfs_lookup()
+    - PCI: loongson: Add more devices that need MRRS quirk
+    - PCI: Add ACS quirk for Wangxun NICs
+    - phy: rockchip-typec: Fix unsigned comparison with less than zero
+    - soundwire: cadence: Remove wasted space in response_buf
+    - soundwire: cadence: Drain the RX FIFO after an IO timeout
+    - net: tls: avoid hanging tasks on the tx_lock
+    - x86/resctl: fix scheduler confusion with 'current'
+    - drm/display/dp_mst: Fix down/up message handling after sink disconnect
+    - drm/display/dp_mst: Fix down message handling after a packet reception error
+    - Bluetooth: hci_sock: purge socket queues in the destruct() callback
+    - media: uvcvideo: Fix race condition with usb_kill_urb
+    - drm/virtio: Fix error code in virtio_gpu_object_shmem_init()
+    - Revert "scsi: mpt3sas: Fix return value check of dma_get_required_mask()"
+    - scsi: mpt3sas: Don't change DMA mask while reallocating pools
+    - scsi: mpt3sas: re-do lost mpt3sas DMA mask fix
+    - scsi: mpt3sas: Remove usage of dma_get_required_mask() API
+    - malidp: Fix NULL vs IS_ERR() checking
+    - usb: gadget: uvc: fix missing mutex_unlock() if kstrtou8() fails
+    - Linux 5.15.100
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+    - [Packaging] update annotations scripts
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Tue, 31 Oct 2023 09:57:14 +1000
+
+linux-xilinx-zynqmp (5.15.0-1023.27) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1023.27 -proposed tracker (LP: #2025252)
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync update-dkms-versions helper
+
+  * Miscellaneous upstream changes
+    - drivers:media Ar1335: Add MODULE DEVICE TABLE entry
+
+  [ Ubuntu: 5.15.0-76.83 ]
+
+  * jammy/linux: 5.15.0-76.83 -proposed tracker (LP: #2023905)
+  * cls_flower: off-by-one in fl_set_geneve_opt (LP: #2023577)
+    - net/sched: flower: fix possible OOB write in fl_set_geneve_opt()
+  * Some INVLPG implementations can leave Global translations unflushed when
+    PCIDs are enabled (LP: #2023220)
+    - x86/mm: Avoid incomplete Global INVLPG flushes
+
+  [ Ubuntu: 5.15.0-75.82 ]
+
+  * jammy/linux: 5.15.0-75.82 -proposed tracker (LP: #2023065)
+  * Jammy update: v5.15.102 upstream stable release (LP: #2020393)
+    - wifi: cfg80211: Partial revert "wifi: cfg80211: Fix use after free for wext"
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync git-ubuntu-log
+    - [Packaging] resync getabis
+  * fix typo in config-checks invocation (LP: #2020413)
+    - [Packaging] fix typo when calling the old config-check
+    - [Packaging] fix typo in 4-checks.mk
+  * support python < 3.9 with annotations (LP: #2020531)
+    - [Packaging] kconfig/annotations.py: support older way of merging dicts
+
+ -- Wen-chien Jesse Sung <jesse.sung@canonical.com>  Wed, 28 Jun 2023 23:01:40 +0800
+
+linux-xilinx-zynqmp (5.15.0-1022.26) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1022.26 -proposed tracker (LP: #2019520)
+
+  * Use new annotations model (LP: #2019000)
+    - [Config] migrate zynqmp config into annotations
+
+  * Update k26 Linux device tree to pull in qspi partition layout changes
+    - arm64: zynqmp: Add mtd partition for secure OS storage area
+
+  * ap1302: add support for test pattern mode
+    - media: i2c: ap1302: Add test pattern control
+
+  * KR260 Device Tree Patch
+    - Added GEM TSU clock properties to KR260 PS GEMs
+
+  * KR260 PL eth ports causing kernel panic with kr07 image
+    - net: axienet: Remove repeated MDIO setup
+    - net: axienet: Remove repeated RX skb handling
+    - net: xilinx: Correct skb passed in error handling path
+
+  * mv-camera-sensor-module: Add support for Y10/Y12 formats
+    - mv-camera-sensor-module: Add support for Y10/Y12 formats
+
+  * Submit kernel patches for AR1335 driver
+    - media:i2c  AR1335 Camera sensor driver support
+    - media: dt-bindings: media: i2c: Add bindings for AR1335
+    - [Config] Enable AR1335 driver as a kernel module
+
+  * Update AMD TSN Preemption and minor bug fixes
+    - lib: add reference counting tracking infrastructure
+    - net: add net device refcount tracker infrastructure
+    - netlink: add net device refcount tracker to struct ethnl_req_info
+    - ethtool: use ethnl_parse_header_dev_put()
+    - net: ethtool: netlink: introduce ethnl_update_bool()
+    - net: ethtool: add support for MAC Merge layer
+    - docs: ethtool-netlink: document interface for MAC Merge layer
+    - net: ethtool: netlink: retrieve stats from multiple sources (eMAC, pMAC)
+    - docs: ethtool: document ETHTOOL_A_STATS_SRC and ETHTOOL_A_PAUSE_STATS_SRC
+    - net: ethtool: add helpers for aggregate statistics
+    - net: ethtool: add helpers for MM fragment size translation
+    - net: dsa: add plumbing for changing and getting MAC merge layer state
+    - net: ethtool: fix NULL pointer dereference in stats_prepare_data()
+    - net: ethtool: fix NULL pointer dereference in pause_prepare_data()
+    - net: ethtool: provide shims for stats aggregation helpers when
+      CONFIG_ETHTOOL_NETLINK=n
+    - ethtool: mm: fix get_mm() return code not propagating to user space
+    - net: ethtool: fix __ethtool_dev_mm_supported() implementation
+    - staging: xilinx-tsn: Add support to configure MAC merge parameters via
+      ethtool
+    - staging: xilinx-tsn: defer temac and switch probe when ep is not probed.
+    - staging: xilinx-tsn: don't exit probe when ep mac address is not found
+    - staging: xilinx-tsn: warn user when temac and ep mac address dont match
+
+  [ Ubuntu: 5.15.0-74.81 ]
+
+  * jammy/linux: 5.15.0-74.81 -proposed tracker (LP: #2019420)
+  * smartpqi: Update 22.04 driver to include recent bug fixes and support
+    current generation devices (LP: #1998643)
+    - scsi: smartpqi: Switch to attribute groups
+    - scsi: smartpqi: Fix rmmod stack trace
+    - scsi: smartpqi: Add PCI IDs
+    - scsi: smartpqi: Enable SATA NCQ priority in sysfs
+    - scsi: smartpqi: Eliminate drive spin down on warm boot
+    - scsi: smartpqi: Quickly propagate path failures to SCSI midlayer
+    - scsi: smartpqi: Fix a name typo and cleanup code
+    - scsi: smartpqi: Fix a typo in func pqi_aio_submit_io()
+    - scsi: smartpqi: Resolve delay issue with PQI_HZ value
+    - scsi: smartpqi: Avoid drive spin-down during suspend
+    - scsi: smartpqi: Update volume size after expansion
+    - scsi: smartpqi: Speed up RAID 10 sequential reads
+    - scsi: smartpqi: Expose SAS address for SATA drives
+    - scsi: smartpqi: Fix NUMA node not updated during init
+    - scsi: smartpqi: Fix BUILD_BUG_ON() statements
+    - scsi: smartpqi: Fix hibernate and suspend
+    - scsi: smartpqi: Fix lsscsi -t SAS addresses
+    - scsi: smartpqi: Update version to 2.1.14-035
+    - scsi: smartpqi: Fix unused variable pqi_pm_ops for clang
+    - scsi: smartpqi: Stop using the SCSI pointer
+    - scsi: smartpqi: Fix typo in comment
+    - scsi: smartpqi: Shorten drive visibility after removal
+    - scsi: smartpqi: Add controller fw version to console log
+    - scsi: smartpqi: Add PCI IDs for ramaxel controllers
+    - scsi: smartpqi: Close write read holes
+    - scsi: smartpqi: Add driver support for multi-LUN devices
+    - scsi: smartpqi: Fix PCI control linkdown system hang
+    - scsi: smartpqi: Add PCI ID for Adaptec SmartHBA 2100-8i
+    - scsi: smartpqi: Add PCI IDs for Lenovo controllers
+    - scsi: smartpqi: Stop logging spurious PQI reset failures
+    - scsi: smartpqi: Fix RAID map race condition
+    - scsi: smartpqi: Add module param to disable managed ints
+    - scsi: smartpqi: Update deleting a LUN via sysfs
+    - scsi: smartpqi: Add ctrl ready timeout module parameter
+    - scsi: smartpqi: Update copyright to current year
+    - scsi: smartpqi: Update version to 2.1.18-045
+    - scsi: smartpqi: Convert to host_tagset
+    - scsi: smartpqi: Add new controller PCI IDs
+    - scsi: smartpqi: Correct max LUN number
+    - scsi: smartpqi: Change sysfs raid_level attribute to N/A for controllers
+    - scsi: smartpqi: Correct device removal for multi-actuator devices
+    - scsi: smartpqi: Add controller cache flush during rmmod
+    - scsi: smartpqi: Initialize feature section info
+    - scsi: smartpqi: Change version to 2.1.20-035
+  * CVE-2023-32233
+    - netfilter: nf_tables: deactivate anonymous set from preparation phase
+  * CVE-2023-2612
+    - SAUCE: shiftfs: prevent lock unbalance in shiftfs_create_object()
+  * CVE-2023-31436
+    - net: sched: sch_qfq: prevent slab-out-of-bounds in qfq_activate_agg
+  * CVE-2023-1380
+    - wifi: brcmfmac: slab-out-of-bounds read in brcmf_get_assoc_ies()
+  * Add  PPIN support for Intel EMR cpu (LP: #2019131)
+    - x86/cpu: Merge Intel and AMD ppin_init() functions
+    - x86/cpu: Add Xeon Emerald Rapids to list of CPUs that support PPIN
+  * conntrack mark is not advertised via netlink (LP: #2016269)
+    - netfilter: ctnetlink: revert to dumping mark regardless of event type
+  * [SRU] Backport request for hpwdt from upstream 6.1 to Jammy (LP: #2008751)
+    - watchdog/hpwdt: Enable HP_WATCHDOG for ARM64 systems.
+    - watchdog/hpwdt: Include nmi.h only if CONFIG_HPWDT_NMI_DECODING
+    - [Config] Add arm64 option to CONFIG_HP_WATCHDOG
+  * Ubuntu 22.04 raise abnormal NIC MSI-X requests with larger CPU cores (256)
+    (LP: #2012335)
+    - ice: Allow operation with reduced device MSI-X
+  * Dell: Enable speaker mute hotkey LED indicator (LP: #2015972)
+    - platform/x86: dell-laptop: Register ctl-led for speaker-mute
+  * [SRU]With "Performance per Watt (DAPC)" enabled in the BIOS, Bootup time is
+    taking longer than expected (LP: #2008527)
+    - cpufreq: ACPI: Defer setting boost MSRs
+  * [SRU][Jammy] CONFIG_PCI_MESON is not enabled (LP: #2007745)
+    - [Config] arm64: Enable PCI_MESON module
+  * Jammy update: v5.15.99 upstream stable release (LP: #2018438)
+    - HID: asus: use spinlock to protect concurrent accesses
+    - HID: asus: use spinlock to safely schedule workers
+    - powerpc/mm: Rearrange if-else block to avoid clang warning
+    - ARM: OMAP2+: Fix memory leak in realtime_counter_init()
+    - arm64: dts: qcom: qcs404: use symbol names for PCIe resets
+    - arm64: dts: qcom: msm8996-tone: Fix USB taking 6 minutes to wake up
+    - arm64: dts: qcom: sm8150-kumano: Panel framebuffer is 2.5k instead of 4k
+    - arm64: dts: qcom: sm6125: Reorder HSUSB PHY clocks to match bindings
+    - arm64: dts: imx8m: Align SoC unique ID node unit address
+    - ARM: zynq: Fix refcount leak in zynq_early_slcr_init
+    - arm64: dts: mediatek: mt8183: Fix systimer 13 MHz clock description
+    - arm64: dts: qcom: sdm845-db845c: fix audio codec interrupt pin name
+    - arm64: dts: qcom: sc7180: correct SPMI bus address cells
+    - arm64: dts: qcom: sc7280: correct SPMI bus address cells
+    - arm64: dts: meson-gx: Fix Ethernet MAC address unit name
+    - arm64: dts: meson-g12a: Fix internal Ethernet PHY unit name
+    - arm64: dts: meson-gx: Fix the SCPI DVFS node name and unit address
+    - arm64: dts: msm8992-bullhead: add memory hole region
+    - arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem size
+    - arm64: dts: qcom: msm8992-bullhead: Disable dfps_data_mem
+    - arm64: dts: qcom: ipq8074: correct USB3 QMP PHY-s clock output names
+    - arm64: dts: qcom: Fix IPQ8074 PCIe PHY nodes
+    - arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
+    - arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY
+    - arm64: dts: qcom: ipq8074: correct Gen2 PCIe ranges
+    - arm64: dts: qcom: ipq8074: fix Gen3 PCIe node
+    - arm64: dts: qcom: ipq8074: correct PCIe QMP PHY output clock names
+    - arm64: dts: meson: remove CPU opps below 1GHz for G12A boards
+    - ARM: OMAP1: call platform_device_put() in error case in
+      omap1_dm_timer_init()
+    - ARM: bcm2835_defconfig: Enable the framebuffer
+    - ARM: s3c: fix s3c64xx_set_timer_source prototype
+    - arm64: dts: ti: k3-j7200: Fix wakeup pinmux range
+    - ARM: dts: exynos: correct wr-active property in Exynos3250 Rinato
+    - ARM: imx: Call ida_simple_remove() for ida_simple_get
+    - arm64: dts: amlogic: meson-gx: fix SCPI clock dvfs node name
+    - arm64: dts: amlogic: meson-axg: fix SCPI clock dvfs node name
+    - arm64: dts: amlogic: meson-gx: add missing SCPI sensors compatible
+    - arm64: dts: amlogic: meson-gxl-s905d-sml5442tw: drop invalid clock-names
+      property
+    - arm64: dts: amlogic: meson-gx: add missing unit address to rng node name
+    - arm64: dts: amlogic: meson-gxl: add missing unit address to eth-phy-mux node
+      name
+    - arm64: dts: amlogic: meson-gx-libretech-pc: fix update button name
+    - arm64: dts: amlogic: meson-sm1-bananapi-m5: fix adc keys node names
+    - arm64: dts: amlogic: meson-gxl-s905d-phicomm-n1: fix led node name
+    - arm64: dts: amlogic: meson-gxbb-kii-pro: fix led node name
+    - arm64: dts: amlogic: meson-sm1-odroid-hc4: fix active fan thermal trip
+    - locking/rwsem: Optimize down_read_trylock() under highly contended case
+    - locking/rwsem: Disable preemption in all down_read*() and up_read() code
+      paths
+    - arm64: dts: renesas: beacon-renesom: Fix gpio expander reference
+    - arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
+    - ARM: dts: sun8i: nanopi-duo2: Fix regulator GPIO reference
+    - ARM: dts: imx7s: correct iomuxc gpr mux controller cells
+    - arm64: dts: mt8192: Fix CPU map for single-cluster SoC
+    - arm64: dts: mediatek: mt7622: Add missing pwm-cells to pwm node
+    - blk-mq: avoid sleep in blk_mq_alloc_request_hctx
+    - blk-mq: remove stale comment for blk_mq_sched_mark_restart_hctx
+    - blk-mq: correct stale comment of .get_budget
+    - arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM
+      and MPSS memory regions
+    - s390/dasd: Fix potential memleak in dasd_eckd_init()
+    - sched/deadline,rt: Remove unused parameter from pick_next_[rt|dl]_entity()
+    - sched/rt: pick_next_rt_entity(): check list_entry
+    - x86/perf/zhaoxin: Add stepping check for ZXC
+    - KEYS: asymmetric: Fix ECDSA use via keyctl uapi
+    - arm64: dts: qcom: pmk8350: Specify PBS register for PON
+    - arm64: dts: qcom: pmk8350: Use the correct PON compatible
+    - block: bio-integrity: Copy flags when bio_integrity_payload is cloned
+    - wifi: rsi: Fix memory leak in rsi_coex_attach()
+    - wifi: rtlwifi: rtl8821ae: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: rtl8188ee: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: rtl8723be: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: iwlegacy: common: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: fix memory leak in lbs_init_adapter()
+    - wifi: rtl8xxxu: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: rtlwifi: Fix global-out-of-bounds bug in
+      _rtl8812ae_phy_set_txpower_limit()
+    - libbpf: Fix btf__align_of() by taking into account field offsets
+    - wifi: ipw2x00: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - wifi: ipw2200: fix memory leak in ipw_wdev_init()
+    - wifi: wilc1000: fix potential memory leak in wilc_mac_xmit()
+    - wifi: brcmfmac: fix potential memory leak in brcmf_netdev_start_xmit()
+    - wifi: brcmfmac: unmap dma buffer in brcmf_msgbuf_alloc_pktid()
+    - wifi: libertas_tf: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: if_usb: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: main: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: libertas: cmdresp: don't call kfree_skb() under spin_lock_irqsave()
+    - wifi: wl3501_cs: don't call kfree_skb() under spin_lock_irqsave()
+    - crypto: x86/ghash - fix unaligned access in ghash_setkey()
+    - ACPICA: Drop port I/O validation for some regions
+    - genirq: Fix the return type of kstat_cpu_irqs_sum()
+    - rcu-tasks: Improve comments explaining tasks_rcu_exit_srcu purpose
+    - rcu-tasks: Remove preemption disablement around srcu_read_[un]lock() calls
+    - rcu-tasks: Fix synchronize_rcu_tasks() VS zap_pid_ns_processes()
+    - lib/mpi: Fix buffer overrun when SG is too long
+    - crypto: ccp - Avoid page allocation failure warning for SEV_GET_ID2
+    - ACPICA: nsrepair: handle cases without a return value correctly
+    - thermal/drivers/tsens: Drop msm8976-specific defines
+    - thermal/drivers/tsens: Add compat string for the qcom,msm8960
+    - thermal/drivers/tsens: Sort out msm8976 vs msm8956 data
+    - thermal/drivers/tsens: fix slope values for msm8939
+    - thermal/drivers/tsens: limit num_sensors to 9 for msm8939
+    - wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
+    - wifi: orinoco: check return value of hermes_write_wordrec()
+    - wifi: ath9k: htc_hst: free skb in ath9k_htc_rx_msg() if there is no callback
+      function
+    - ath9k: hif_usb: simplify if-if to if-else
+    - ath9k: htc: clean up statistics macros
+    - wifi: ath9k: hif_usb: clean up skbs if ath9k_hif_usb_rx_stream() fails
+    - wifi: ath9k: Fix potential stack-out-of-bounds write in
+      ath9k_wmi_rsp_callback()
+    - wifi: ath11k: Fix memory leak in ath11k_peer_rx_frag_setup
+    - wifi: cfg80211: Fix extended KCK key length check in
+      nl80211_set_rekey_data()
+    - ACPI: battery: Fix missing NUL-termination with large strings
+    - crypto: ccp - Failure on re-initialization due to duplicate sysfs filename
+    - crypto: essiv - Handle EBUSY correctly
+    - crypto: seqiv - Handle EBUSY correctly
+    - powercap: fix possible name leak in powercap_register_zone()
+    - x86: Mark stop_this_cpu() __noreturn
+    - x86/microcode: Rip out the OLD_INTERFACE
+    - [Config] Drop MICROCODE_OLD_INTERFACE
+    - x86/microcode: Default-disable late loading
+    - x86/microcode: Print previous version of microcode after reload
+    - x86/microcode: Add a parameter to microcode_check() to store CPU
+      capabilities
+    - x86/microcode: Check CPU capabilities after late microcode update correctly
+    - x86/microcode: Adjust late loading result reporting message
+    - crypto: xts - Handle EBUSY correctly
+    - leds: led-class: Add missing put_device() to led_put()
+    - crypto: ccp - Refactor out sev_fw_alloc()
+    - crypto: ccp - Flush the SEV-ES TMR memory before giving it to firmware
+    - bpftool: profile online CPUs instead of possible
+    - mt76: mt7915: fix polling firmware-own status
+    - net/mlx5: Enhance debug print in page allocation failure
+    - irqchip: Fix refcount leak in platform_irqchip_probe
+    - irqchip/alpine-msi: Fix refcount leak in alpine_msix_init_domains
+    - irqchip/irq-mvebu-gicp: Fix refcount leak in mvebu_gicp_probe
+    - irqchip/ti-sci: Fix refcount leak in ti_sci_intr_irq_domain_probe
+    - s390/mem_detect: fix detect_memory() error handling
+    - s390/vmem: fix empty page tables cleanup under KASAN
+    - net: add sock_init_data_uid()
+    - tun: tun_chr_open(): correctly initialize socket uid
+    - tap: tap_open(): correctly initialize socket uid
+    - OPP: fix error checking in opp_migrate_dentry()
+    - Bluetooth: L2CAP: Fix potential user-after-free
+    - Bluetooth: hci_qca: get wakeup status from serdev device handle
+    - s390/ap: fix status returned by ap_aqic()
+    - s390/ap: fix status returned by ap_qact()
+    - libbpf: Fix alen calculation in libbpf_nla_dump_errormsg()
+    - rds: rds_rm_zerocopy_callback() correct order for list_add_tail()
+    - crypto: rsa-pkcs1pad - Use akcipher_request_complete
+    - m68k: /proc/hardware should depend on PROC_FS
+    - RISC-V: time: initialize hrtimer based broadcast clock event device
+    - wifi: iwl3945: Add missing check for create_singlethread_workqueue
+    - wifi: iwl4965: Add missing check for create_singlethread_workqueue()
+    - wifi: mwifiex: fix loop iterator in mwifiex_update_ampdu_txwinsize()
+    - selftests/bpf: Fix out-of-srctree build
+    - ACPI: resource: Add IRQ overrides for MAINGEAR Vector Pro 2 models
+    - ACPI: resource: Do IRQ override on all TongFang GMxRGxx
+    - crypto: crypto4xx - Call dma_unmap_page when done
+    - wifi: mac80211: make rate u32 in sta_set_rate_info_rx()
+    - thermal/drivers/hisi: Drop second sensor hi3660
+    - can: esd_usb: Move mislocated storage of SJA1000_ECC_SEG bits in case of a
+      bus error
+    - bpf: Fix global subprog context argument resolution logic
+    - irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts
+    - irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts
+    - selftests/net: Interpret UDP_GRO cmsg data as an int value
+    - l2tp: Avoid possible recursive deadlock in l2tp_tunnel_register()
+    - net: bcmgenet: fix MoCA LED control
+    - sefltests: netdevsim: wait for devlink instance after netns removal
+    - drm: Fix potential null-ptr-deref due to drmm_mode_config_init()
+    - drm/fourcc: Add missing big-endian XRGB1555 and RGB565 formats
+    - drm/bridge: ti-sn65dsi83: Fix delay after reset deassert to match spec
+    - drm: mxsfb: DRM_MXSFB should depend on ARCH_MXS || ARCH_MXC
+    - [Config] Drop DRM_MXSFB for armhf-generic-lpae
+    - drm/bridge: megachips: Fix error handling in i2c_register_driver()
+    - drm/vkms: Fix memory leak in vkms_init()
+    - drm/vkms: Fix null-ptr-deref in vkms_release()
+    - drm/vc4: dpi: Add option for inverting pixel clock and output enable
+    - drm/vc4: dpi: Fix format mapping for RGB565
+    - drm: tidss: Fix pixel format definition
+    - gpu: ipu-v3: common: Add of_node_put() for reference returned by
+      of_graph_get_port_by_id()
+    - hwmon: (ftsteutates) Fix scaling of measurements
+    - drm/msm/hdmi: Add missing check for alloc_ordered_workqueue
+    - pinctrl: qcom: pinctrl-msm8976: Correct function names for wcss pins
+    - pinctrl: stm32: Fix refcount leak in stm32_pctrl_get_irq_domain
+    - pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
+    - drm/vc4: hvs: Set AXI panic modes
+    - drm/vc4: hvs: Fix colour order for xRGB1555 on HVS5
+    - drm/vc4: hdmi: Correct interlaced timings again
+    - drm/msm: clean event_thread->worker in case of an error
+    - scsi: qla2xxx: edif: Fix I/O timeout due to over-subscription
+    - scsi: qla2xxx: Fix exchange oversubscription
+    - scsi: qla2xxx: Fix exchange oversubscription for management commands
+    - ASoC: fsl_sai: Update to modern clocking terminology
+    - ASoC: fsl_sai: initialize is_dsp_mode flag
+    - drm/msm/adreno: Fix null ptr access in adreno_gpu_cleanup()
+    - ALSA: hda/ca0132: minor fix for allocation size
+    - drm/msm/gem: Add check for kmalloc
+    - drm/msm/dpu: Disallow unallocated resources to be returned
+    - drm/bridge: lt9611: fix sleep mode setup
+    - drm/bridge: lt9611: fix HPD reenablement
+    - drm/bridge: lt9611: fix polarity programming
+    - drm/bridge: lt9611: fix programming of video modes
+    - drm/bridge: lt9611: fix clock calculation
+    - drm/bridge: lt9611: pass a pointer to the of node
+    - drm/mipi-dsi: Fix byte order of 16-bit DCS set/get brightness
+    - drm: exynos: dsi: Fix MIPI_DSI*_NO_* mode flags
+    - drm/msm/dsi: Allow 2 CTRLs on v2.5.0
+    - drm/msm: use strscpy instead of strncpy
+    - drm/msm/dpu: Add check for cstate
+    - drm/msm/dpu: Add check for pstates
+    - drm/msm/mdp5: Add check for kzalloc
+    - pinctrl: bcm2835: Remove of_node_put() in bcm2835_of_gpio_ranges_fallback()
+    - pinctrl: mediatek: fix coding style
+    - pinctrl: mediatek: Initialize variable pullen and pullup to zero
+    - pinctrl: mediatek: Initialize variable *buf to zero
+    - gpu: host1x: Don't skip assigning syncpoints to channels
+    - drm/tegra: firewall: Check for is_addr_reg existence in IMM check
+    - drm/msm/dpu: set pdpu->is_rt_pipe early in dpu_plane_sspp_atomic_update()
+    - drm/mediatek: dsi: Reduce the time of dsi from LP11 to sending cmd
+    - drm/mediatek: Use NULL instead of 0 for NULL pointer
+    - drm/mediatek: Drop unbalanced obj unref
+    - drm/mediatek: mtk_drm_crtc: Add checks for devm_kcalloc
+    - drm/mediatek: Clean dangling pointer on bind error path
+    - ASoC: soc-compress.c: fixup private_data on snd_soc_new_compress()
+    - gpio: vf610: connect GPIO label to dev name
+    - spi: dw_bt1: fix MUX_MMIO dependencies
+    - ASoC: mchp-spdifrx: fix controls which rely on rsr register
+    - ASoC: mchp-spdifrx: fix return value in case completion times out
+    - ASoC: mchp-spdifrx: fix controls that works with completion mechanism
+    - ASoC: mchp-spdifrx: disable all interrupts in mchp_spdifrx_dai_remove()
+    - ASoC: rsnd: fixup #endif position
+    - ASoC: mchp-spdifrx: Fix uninitialized use of mr in mchp_spdifrx_hw_params()
+    - ASoC: dt-bindings: meson: fix gx-card codec node regex
+    - hwmon: (ltc2945) Handle error case in ltc2945_value_store
+    - drm/amdgpu: fix enum odm_combine_mode mismatch
+    - scsi: mpt3sas: Fix a memory leak
+    - scsi: aic94xx: Add missing check for dma_map_single()
+    - HID: multitouch: Add quirks for flipped axes
+    - HID: retain initial quirks set up when creating HID devices
+    - ASoC: codecs: Change bulk clock voting to optional voting in digital codecs
+    - ASoC: codecs: rx-macro: move clk provider to managed variants
+    - ASoC: codecs: tx-macro: move clk provider to managed variants
+    - ASoC: codecs: rx-macro: move to individual clks from bulk
+    - ASoC: codecs: tx-macro: move to individual clks from bulk
+    - ASoC: codecs: lpass: fix incorrect mclk rate
+    - spi: bcm63xx-hsspi: Fix multi-bit mode setting
+    - hwmon: (mlxreg-fan) Return zero speed for broken fan
+    - ASoC: tlv320adcx140: fix 'ti,gpio-config' DT property init
+    - dm: remove flush_scheduled_work() during local_exit()
+    - NFSv4: keep state manager thread active if swap is enabled
+    - nfs4trace: fix state manager flag printing
+    - NFS: fix disabling of swap
+    - spi: synquacer: Fix timeout handling in synquacer_spi_transfer_one()
+    - ASoC: soc-dapm.h: fixup warning struct snd_pcm_substream not declared
+    - HID: bigben: use spinlock to protect concurrent accesses
+    - HID: bigben_worker() remove unneeded check on report_field
+    - HID: bigben: use spinlock to safely schedule workers
+    - hid: bigben_probe(): validate report count
+    - drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
+    - nfsd: fix race to check ls_layouts
+    - cifs: Fix lost destroy smbd connection when MR allocate failed
+    - cifs: Fix warning and UAF when destroy the MR list
+    - gfs2: jdata writepage fix
+    - perf llvm: Fix inadvertent file creation
+    - leds: led-core: Fix refcount leak in of_led_get()
+    - perf inject: Use perf_data__read() for auxtrace
+    - perf intel-pt: Add documentation for Event Trace and TNT disable
+    - perf intel-pt: Add link to the perf wiki's Intel PT page
+    - perf intel-pt: Add support for emulated ptwrite
+    - perf intel-pt: Do not try to queue auxtrace data on pipe
+    - perf tools: Fix auto-complete on aarch64
+    - sparc: allow PM configs for sparc32 COMPILE_TEST
+    - printf: fix errname.c list
+    - objtool: add UACCESS exceptions for __tsan_volatile_read/write
+    - mfd: cs5535: Don't build on UML
+    - mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
+    - dmaengine: idxd: Set traffic class values in GRPCFG on DSA 2.0
+    - dmaengine: HISI_DMA should depend on ARCH_HISI
+    - [Config] Add HISI_DMA=n for armhf
+    - iio: light: tsl2563: Do not hardcode interrupt trigger type
+    - usb: gadget: fusb300_udc: free irq on the error path in fusb300_probe()
+    - i2c: designware: fix i2c_dw_clk_rate() return size to be u32
+    - soundwire: cadence: Don't overflow the command FIFOs
+    - driver core: fix potential null-ptr-deref in device_add()
+    - kobject: modify kobject_get_path() to take a const *
+    - kobject: Fix slab-out-of-bounds in fill_kobj_path()
+    - alpha/boot/tools/objstrip: fix the check for ELF header
+    - media: uvcvideo: Do not check for V4L2_CTRL_WHICH_DEF_VAL
+    - media: uvcvideo: Remove s_ctrl and g_ctrl
+    - media: uvcvideo: refactor __uvc_ctrl_add_mapping
+    - media: uvcvideo: Add support for V4L2_CTRL_TYPE_CTRL_CLASS
+    - media: uvcvideo: Use control names from framework
+    - media: uvcvideo: Check controls flags before accessing them
+    - media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()
+    - coresight: etm4x: Fix accesses to TRCSEQRSTEVR and TRCSEQSTR
+    - coresight: cti: Prevent negative values of enable count
+    - coresight: cti: Add PM runtime call in enable_store
+    - ACPI: resource: Add helper function acpi_dev_get_memory_resources()
+    - usb: typec: intel_pmc_mux: Use the helper acpi_dev_get_memory_resources()
+    - usb: typec: intel_pmc_mux: Don't leak the ACPI device reference count
+    - PCI/IOV: Enlarge virtfn sysfs name buffer
+    - PCI: switchtec: Return -EFAULT for copy_to_user() errors
+    - tty: serial: fsl_lpuart: disable Rx/Tx DMA in lpuart32_shutdown()
+    - tty: serial: fsl_lpuart: clear LPUART Status Register in lpuart32_shutdown()
+    - serial: tegra: Add missing clk_disable_unprepare() in tegra_uart_hw_init()
+    - Revert "char: pcmcia: cm4000_cs: Replace mdelay with usleep_range in
+      set_protocol"
+    - eeprom: idt_89hpesx: Fix error handling in idt_init()
+    - applicom: Fix PCI device refcount leak in applicom_init()
+    - firmware: stratix10-svc: add missing gen_pool_destroy() in
+      stratix10_svc_drv_probe()
+    - VMCI: check context->notify_page after call to get_user_pages_fast() to
+      avoid GPF
+    - misc/mei/hdcp: Use correct macros to initialize uuid_le
+    - driver core: fix resource leak in device_add()
+    - drivers: base: transport_class: fix possible memory leak
+    - drivers: base: transport_class: fix resource leak when
+      transport_add_device() fails
+    - firmware: dmi-sysfs: Fix null-ptr-deref in dmi_sysfs_register_handle
+    - fotg210-udc: Add missing completion handler
+    - dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
+    - usb: early: xhci-dbc: Fix a potential out-of-bound memory access
+    - tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case
+    - RDMA/cxgb4: add null-ptr-check after ip_dev_find()
+    - usb: musb: mediatek: don't unregister something that wasn't registered
+    - usb: gadget: configfs: use to_config_usb_cfg() in os_desc_link()
+    - usb: gadget: configfs: use to_usb_function_instance() in cfg (un)link func
+    - usb: gadget: configfs: remove using list iterator after loop body as a ptr
+    - usb: gadget: configfs: Restrict symlink creation is UDC already binded
+    - iommu/vt-d: Set No Execute Enable bit in PASID table entry
+    - power: supply: remove faulty cooling logic
+    - RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish()
+    - usb: max-3421: Fix setting of I/O pins
+    - RDMA/irdma: Cap MSIX used to online CPUs + 1
+    - serial: fsl_lpuart: fix RS485 RTS polariy inverse issue
+    - tty: serial: imx: Handle RS485 DE signal active high
+    - tty: serial: imx: disable Ageing Timer interrupt request irq
+    - dmaengine: dw-edma: Fix readq_ch() return value truncation
+    - phy: rockchip-typec: fix tcphy_get_mode error case
+    - iw_cxgb4: Fix potential NULL dereference in c4iw_fill_res_cm_id_entry()
+    - iommu: Fix error unwind in iommu_group_alloc()
+    - dmaengine: sf-pdma: pdma_desc memory leak fix
+    - dmaengine: dw-axi-dmac: Do not dereference NULL structure
+    - iommu/vt-d: Fix error handling in sva enable/disable paths
+    - iommu/vt-d: Remove duplicate identity domain flag
+    - iommu/vt-d: Check FL and SL capability sanity in scalable mode
+    - iommu/vt-d: Use second level for GPA->HPA translation
+    - iommu/vt-d: Allow to use flush-queue when first level is default
+    - IB/hfi1: Fix math bugs in hfi1_can_pin_pages()
+    - IB/hfi1: Fix sdma.h tx->num_descs off-by-one errors
+    - remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headers
+    - media: ti: cal: fix possible memory leak in cal_ctx_create()
+    - media: platform: ti: Add missing check for devm_regulator_get
+    - powerpc: Remove linker flag from KBUILD_AFLAGS
+    - s390/vdso: remove -nostdlib compiler flag
+    - s390/vdso: Drop '-shared' from KBUILD_CFLAGS_64
+    - builddeb: clean generated package content
+    - media: max9286: Fix memleak in max9286_v4l2_register()
+    - media: ov2740: Fix memleak in ov2740_init_controls()
+    - media: ov5675: Fix memleak in ov5675_init_controls()
+    - media: i2c: ov772x: Fix memleak in ov772x_probe()
+    - media: i2c: imx219: Split common registers from mode tables
+    - media: i2c: imx219: Fix binning for RAW8 capture
+    - media: v4l2-jpeg: correct the skip count in jpeg_parse_app14_data
+    - media: v4l2-jpeg: ignore the unknown APP14 marker
+    - media: imx-jpeg: Apply clk_bulk api instead of operating specific clk
+    - media: i2c: ov7670: 0 instead of -EINVAL was returned
+    - media: usb: siano: Fix use after free bugs caused by do_submit_urb
+    - media: saa7134: Use video_unregister_device for radio_dev
+    - rpmsg: glink: Avoid infinite loop on intent for missing channel
+    - udf: Define EFSCORRUPTED error code
+    - ARM: dts: exynos: Use Exynos5420 compatible for the MIPI video phy
+    - blk-iocost: fix divide by 0 error in calc_lcoefs()
+    - trace/blktrace: fix memory leak with using debugfs_lookup()
+    - wifi: ath9k: Fix use-after-free in ath9k_hif_usb_disconnect()
+    - wifi: brcmfmac: Fix potential stack-out-of-bounds in brcmf_c_preinit_dcmds()
+    - rcu: Make RCU_LOCKDEP_WARN() avoid early lockdep checks
+    - rcu: Suppress smp_processor_id() complaint in
+      synchronize_rcu_expedited_wait()
+    - rcu-tasks: Make rude RCU-Tasks work well with CPU hotplug
+    - wifi: ath11k: debugfs: fix to work with multiple PCI devices
+    - thermal: intel: Fix unsigned comparison with less than zero
+    - timers: Prevent union confusion from unexpected restart_syscall()
+    - x86/bugs: Reset speculation control settings on init
+    - wifi: brcmfmac: ensure CLM version is null-terminated to prevent stack-out-
+      of-bounds
+    - wifi: mt7601u: fix an integer underflow
+    - inet: fix fast path in __inet_hash_connect()
+    - ice: restrict PTP HW clock freq adjustments to 100, 000, 000 PPB
+    - ice: add missing checks for PF vsi type
+    - ACPI: Don't build ACPICA with '-Os'
+    - thermal: intel: intel_pch: Add support for Wellsburg PCH
+    - clocksource: Suspend the watchdog temporarily when high read latency
+      detected
+    - crypto: hisilicon: Wipe entire pool on error
+    - net: bcmgenet: Add a check for oversized packets
+    - m68k: Check syscall_trace_enter() return code
+    - netfilter: nf_tables: NULL pointer dereference in nf_tables_updobj()
+    - wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
+    - ACPI: video: Fix Lenovo Ideapad Z570 DMI match
+    - net/mlx5: fw_tracer: Fix debug print
+    - coda: Avoid partial allocation of sig_inputArgs
+    - uaccess: Add minimum bounds check on kernel buffer size
+    - s390/idle: mark arch_cpu_idle() noinstr
+    - time/debug: Fix memory leak with using debugfs_lookup()
+    - PM: domains: fix memory leak with using debugfs_lookup()
+    - PM: EM: fix memory leak with using debugfs_lookup()
+    - Bluetooth: btusb: Add VID:PID 13d3:3529 for Realtek RTL8821CE
+    - hv_netvsc: Check status in SEND_RNDIS_PKT completion message
+    - scm: add user copy checks to put_cmsg()
+    - drm/amd/display: Revert Reduce delay when sink device not able to ACK 00340h
+      write
+    - drm/amd/display: Fix potential null-deref in dm_resume
+    - drm/omap: dsi: Fix excessive stack usage
+    - HID: Add Mapping for System Microphone Mute
+    - drm/tiny: ili9486: Do not assume 8-bit only SPI controllers
+    - drm/radeon: free iio for atombios when driver shutdown
+    - scsi: lpfc: Fix use-after-free KFENCE violation during sysfs firmware write
+    - Revert "fbcon: don't lose the console font across generic->chip driver
+      switch"
+    - drm: amd: display: Fix memory leakage
+    - drm/msm/dsi: Add missing check for alloc_ordered_workqueue
+    - docs/scripts/gdb: add necessary make scripts_gdb step
+    - ASoC: soc-compress: Reposition and add pcm_mutex
+    - ASoC: kirkwood: Iterate over array indexes instead of using pointer math
+    - regulator: max77802: Bounds check regulator id against opmode
+    - regulator: s5m8767: Bounds check id indexing into arrays
+    - gfs2: Improve gfs2_make_fs_rw error handling
+    - hwmon: (coretemp) Simplify platform device handling
+    - pinctrl: at91: use devm_kasprintf() to avoid potential leaks
+    - scsi: snic: Fix memory leak with using debugfs_lookup()
+    - HID: logitech-hidpp: Don't restart communication if not necessary
+    - drm: panel-orientation-quirks: Add quirk for Lenovo IdeaPad Duet 3 10IGL5
+    - dm thin: add cond_resched() to various workqueue loops
+    - dm cache: add cond_resched() to various workqueue loops
+    - nfsd: zero out pointers after putting nfsd_files on COPY setup error
+    - drm/shmem-helper: Revert accidental non-GPL export
+    - wifi: rtl8xxxu: fixing transmisison failure for rtl8192eu
+    - firmware: coreboot: framebuffer: Ignore reserved pixel color bits
+    - block: don't allow multiple bios for IOCB_NOWAIT issue
+    - rtc: pm8xxx: fix set-alarm race
+    - ipmi:ssif: resend_msg() cannot fail
+    - ipmi_ssif: Rename idle state and check
+    - s390/extmem: return correct segment type in __segment_load()
+    - s390: discard .interp section
+    - s390/kprobes: fix irq mask clobbering on kprobe reenter from post_handler
+    - s390/kprobes: fix current_kprobe never cleared after kprobes reenter
+    - cifs: Fix uninitialized memory read in smb3_qfs_tcon()
+    - btrfs: hold block group refcount during async discard
+    - locking/rwsem: Prevent non-first waiter from spinning in down_write()
+      slowpath
+    - ksmbd: fix wrong data area length for smb2 lock request
+    - ksmbd: do not allow the actual frame length to be smaller than the rfc1002
+      length
+    - ARM: dts: exynos: correct HDMI phy compatible in Exynos4
+    - hfs: fix missing hfs_bnode_get() in __hfs_bnode_create
+    - fs: hfsplus: fix UAF issue in hfsplus_put_super
+    - exfat: fix reporting fs error when reading dir beyond EOF
+    - exfat: fix unexpected EOF while reading dir
+    - exfat: redefine DIR_DELETED as the bad cluster number
+    - exfat: fix inode->i_blocks for non-512 byte sector size device
+    - fs: dlm: don't set stop rx flag after node reset
+    - fs: dlm: move sending fin message into state change handling
+    - fs: dlm: send FIN ack back in right cases
+    - f2fs: fix information leak in f2fs_move_inline_dirents()
+    - f2fs: fix cgroup writeback accounting with fs-layer encryption
+    - ocfs2: fix defrag path triggering jbd2 ASSERT
+    - ocfs2: fix non-auto defrag path not working issue
+    - selftests/landlock: Skip overlayfs tests when not supported
+    - selftests/landlock: Test ptrace as much as possible with Yama
+    - udf: Truncate added extents on failed expansion
+    - udf: Do not bother merging very long extents
+    - udf: Do not update file length for failed writes to inline files
+    - udf: Preserve link count of system files
+    - udf: Detect system inodes linked into directory hierarchy
+    - udf: Fix file corruption when appending just after end of preallocated
+      extent
+    - RDMA/siw: Fix user page pinning accounting
+    - KVM: Destroy target device if coalesced MMIO unregistration fails
+    - KVM: x86: Inject #GP if WRMSR sets reserved bits in APIC Self-IPI
+    - KVM: SVM: Fix potential overflow in SEV's send|receive_update_data()
+    - KVM: SVM: hyper-v: placate modpost section mismatch error
+    - KVM: s390: disable migration mode when dirty tracking is disabled
+    - x86/virt: Force GIF=1 prior to disabling SVM (for reboot flows)
+    - x86/crash: Disable virt in core NMI crash handler to avoid double shootdown
+    - x86/reboot: Disable virtualization in an emergency if SVM is supported
+    - x86/reboot: Disable SVM, not just VMX, when stopping CPUs
+    - x86/kprobes: Fix __recover_optprobed_insn check optimizing logic
+    - x86/kprobes: Fix arch_check_optimized_kprobe check within optimized_kprobe
+      range
+    - x86/microcode/amd: Remove load_microcode_amd()'s bsp parameter
+    - x86/microcode/AMD: Add a @cpu parameter to the reloading functions
+    - x86/microcode/AMD: Fix mixed steppings support
+    - x86/speculation: Allow enabling STIBP with legacy IBRS
+    - Documentation/hw-vuln: Document the interaction between IBRS and STIBP
+    - brd: return 0/-error from brd_insert_page()
+    - ima: Align ima_file_mmap() parameters with mmap_file LSM hook
+    - irqdomain: Fix association race
+    - irqdomain: Fix disassociation race
+    - irqdomain: Look for existing mapping only once
+    - irqdomain: Drop bogus fwspec-mapping error handling
+    - irqdomain: Fix domain registration race
+    - crypto: qat - fix out-of-bounds read
+    - io_uring: handle TIF_NOTIFY_RESUME when checking for task_work
+    - io_uring: mark task TASK_RUNNING before handling resume/task work
+    - io_uring: add a conditional reschedule to the IOPOLL cancelation loop
+    - io_uring/rsrc: disallow multi-source reg buffers
+    - io_uring: remove MSG_NOSIGNAL from recvmsg
+    - io_uring/poll: allow some retries for poll triggering spuriously
+    - ALSA: ice1712: Do not left ice->gpio_mutex locked in aureon_add_controls()
+    - ALSA: hda/realtek: Add quirk for HP EliteDesk 800 G6 Tower PC
+    - jbd2: fix data missing when reusing bh which is ready to be checkpointed
+    - ext4: optimize ea_inode block expansion
+    - ext4: refuse to create ea block when umounted
+    - mtd: spi-nor: sfdp: Fix index value for SCCR dwords
+    - mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
+    - mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
+    - dm: send just one event on resize, not two
+    - dm: add cond_resched() to dm_wq_work()
+    - wifi: rtl8xxxu: Use a longer retry limit of 48
+    - wifi: ath11k: allow system suspend to survive ath11k
+    - wifi: cfg80211: Fix use after free for wext
+    - qede: fix interrupt coalescing configuration
+    - thermal: intel: powerclamp: Fix cur_state for multi package system
+    - dm flakey: fix logic when corrupting a bio
+    - dm flakey: don't corrupt the zero page
+    - dm flakey: fix a bug with 32-bit highmem systems
+    - ARM: dts: qcom: sdx55: Add Qcom SMMU-500 as the fallback for IOMMU node
+    - ARM: dts: exynos: correct TMU phandle in Exynos4210
+    - ARM: dts: exynos: correct TMU phandle in Exynos4
+    - ARM: dts: exynos: correct TMU phandle in Odroid XU3 family
+    - ARM: dts: exynos: correct TMU phandle in Exynos5250
+    - ARM: dts: exynos: correct TMU phandle in Odroid XU
+    - ARM: dts: exynos: correct TMU phandle in Odroid HC1
+    - fuse: add inode/permission checks to fileattr_get/fileattr_set
+    - rbd: avoid use-after-free in do_rbd_add() when rbd_dev_create() fails
+    - ceph: update the time stamps and try to drop the suid/sgid
+    - alpha: fix FEN fault handling
+    - dax/kmem: Fix leak of memory-hotplug resources
+    - mips: fix syscall_get_nr
+    - media: ipu3-cio2: Fix PM runtime usage_count in driver unbind
+    - remoteproc/mtk_scp: Move clk ops outside send_lock
+    - docs: gdbmacros: print newest record
+    - mm: memcontrol: deprecate charge moving
+    - mm/thp: check and bail out if page in deferred queue already
+    - ktest.pl: Give back console on Ctrt^C on monitor
+    - ktest.pl: Fix missing "end_monitor" when machine check fails
+    - ktest.pl: Add RUN_TIMEOUT option with default unlimited
+    - ring-buffer: Handle race between rb_move_tail and rb_check_pages
+    - tools/bootconfig: fix single & used for logical condition
+    - scsi: qla2xxx: Fix link failure in NPIV environment
+    - scsi: qla2xxx: Check if port is online before sending ELS
+    - scsi: qla2xxx: Fix DMA-API call trace on NVMe LS requests
+    - scsi: qla2xxx: Remove unintended flag clearing
+    - scsi: qla2xxx: Fix erroneous link down
+    - scsi: qla2xxx: Remove increment of interface err cnt
+    - scsi: ses: Don't attach if enclosure has no components
+    - scsi: ses: Fix slab-out-of-bounds in ses_enclosure_data_process()
+    - scsi: ses: Fix possible addl_desc_ptr out-of-bounds accesses
+    - scsi: ses: Fix possible desc_ptr out-of-bounds accesses
+    - scsi: ses: Fix slab-out-of-bounds in ses_intf_remove()
+    - RISC-V: add a spin_shadow_stack declaration
+    - riscv: mm: fix regression due to update_mmu_cache change
+    - riscv: jump_label: Fixup unaligned arch_static_branch function
+    - riscv, mm: Perform BPF exhandler fixup on page fault
+    - riscv: ftrace: Remove wasted nops for !RISCV_ISA_C
+    - riscv: ftrace: Reduce the detour code size to half
+    - MIPS: DTS: CI20: fix otg power gpio
+    - PCI/PM: Observe reset delay irrespective of bridge_d3
+    - PCI: hotplug: Allow marking devices as disconnected during bind/unbind
+    - PCI: Avoid FLR for AMD FCH AHCI adapters
+    - iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
+    - vfio/type1: prevent underflow of locked_vm via exec()
+    - vfio/type1: track locked_vm per dma
+    - vfio/type1: restore locked_vm
+    - drm/i915/quirks: Add inverted backlight quirk for HP 14-r206nv
+    - drm/radeon: Fix eDP for single-display iMac11,2
+    - drm/edid: fix AVI infoframe aspect ratio handling
+    - perf intel-pt: pkt-decoder: Add CFE and EVD packets
+    - qede: avoid uninitialized entries in coal_entry array
+    - media: uvcvideo: Fix memory leak of object map on error exit path
+    - iommu/vt-d: Fix an unbalanced rcu_read_lock/rcu_read_unlock()
+    - arm64: dts: qcom: ipq8074: fix Gen2 PCIe QMP PHY
+    - wifi: ath9k: use proper statements in conditionals
+    - kbuild: Port silent mode detection to future gnu make.
+    - Linux 5.15.99
+    - [Config] Stop expecting mxsfb for ppc64el
+  * Use new annotations model (LP: #2019000)
+    - [Packaging] new annotations model infrastructure
+    - [Config] migrate all configs into annotations
+  * CVE-2023-30456
+    - KVM: nVMX: add missing consistency checks for CR0 and CR4
+  * CVE-2023-1859
+    - 9p/xen : Fix use after free bug in xen_9pfs_front_remove due to race
+      condition
+  * CVE-2023-1670
+    - xirc2ps_cs: Fix use after free bug in xirc2ps_detach
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  [ Ubuntu: 5.15.0-72.79 ]
+
+  * jammy/linux: 5.15.0-72.79 -proposed tracker (LP: #2016548)
+  * Add split lock detection for EMR (LP: #2015855)
+    - x86/split_lock: Enumerate architectural split lock disable bit
+  *  selftest: fib_tests: Always cleanup before exit  (LP: #2015956)
+    - selftest: fib_tests: Always cleanup before exit
+  * Add support for intel EMR cpu (LP: #2015372)
+    - platform/x86: intel-uncore-freq: add Emerald Rapids support
+    - perf/x86/intel/cstate: Add Emerald Rapids
+    - perf/x86/rapl: Add support for Intel Emerald Rapids
+    - intel_idle: add Emerald Rapids Xeon support
+    - tools/power/x86/intel-speed-select: Add Emerald Rapid quirk
+    - tools/power turbostat: Introduce support for EMR
+    - powercap: intel_rapl: add support for Emerald Rapids
+    - EDAC/i10nm: Add Intel Emerald Rapids server support
+  * Kernel livepatch ftrace graph fix (LP: #2013603)
+    - kprobes: treewide: Remove trampoline_address from
+      kretprobe_trampoline_handler()
+    - kprobes: treewide: Make it harder to refer kretprobe_trampoline directly
+    - kprobes: Add kretprobe_find_ret_addr() for searching return address
+    - s390/unwind: recover kretprobe modified return address in stacktrace
+    - s390/unwind: fix fgraph return address recovery
+  * Jammy update: v5.15.98 upstream stable release (LP: #2015600)
+    - Linux 5.15.98
+  * Jammy update: v5.15.97 upstream stable release (LP: #2015599)
+    - ionic: refactor use of ionic_rx_fill()
+    - Fix XFRM-I support for nested ESP tunnels
+    - arm64: dts: rockchip: drop unused LED mode property from rk3328-roc-cc
+    - ARM: dts: rockchip: add power-domains property to dp node on rk3288
+    - HID: elecom: add support for TrackBall 056E:011C
+    - ACPI: NFIT: fix a potential deadlock during NFIT teardown
+    - btrfs: send: limit number of clones and allocated memory size
+    - ASoC: rt715-sdca: fix clock stop prepare timeout issue
+    - IB/hfi1: Assign npages earlier
+    - neigh: make sure used and confirmed times are valid
+    - HID: core: Fix deadloop in hid_apply_multiplier.
+    - x86/cpu: Add Lunar Lake M
+    - staging: mt7621-dts: change palmbus address to lower case
+    - bpf: bpf_fib_lookup should not return neigh in NUD_FAILED state
+    - net: Remove WARN_ON_ONCE(sk->sk_forward_alloc) from sk_stream_kill_queues().
+    - vc_screen: don't clobber return value in vcs_read
+    - scripts/tags.sh: Invoke 'realpath' via 'xargs'
+    - scripts/tags.sh: fix incompatibility with PCRE2
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-M
+    - USB: serial: option: add support for VW/Skoda "Carstick LTE"
+    - usb: gadget: u_serial: Add null pointer check in gserial_resume
+    - USB: core: Don't hold device lock while reading the "descriptors" sysfs file
+    - Linux 5.15.97
+  * Jammy update: v5.15.96 upstream stable release (LP: #2015595)
+    - drm/etnaviv: don't truncate physical page address
+    - wifi: rtl8xxxu: gen2: Turn on the rate control
+    - drm/edid: Fix minimum bpc supported with DSC1.2 for HDMI sink
+    - clk: mxl: Switch from direct readl/writel based IO to regmap based IO
+    - clk: mxl: Remove redundant spinlocks
+    - clk: mxl: Add option to override gate clks
+    - clk: mxl: Fix a clk entry by adding relevant flags
+    - powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
+    - clk: mxl: syscon_node_to_regmap() returns error pointers
+    - random: always mix cycle counter in add_latent_entropy()
+    - KVM: x86: Fail emulation during EMULTYPE_SKIP on any exception
+    - KVM: SVM: Skip WRMSR fastpath on VM-Exit if next RIP isn't valid
+    - can: kvaser_usb: hydra: help gcc-13 to figure out cmd_len
+    - powerpc: dts: t208x: Disable 10G on MAC1 and MAC2
+    - powerpc: use generic version of arch_is_kernel_initmem_freed()
+    - powerpc/vmlinux.lds: Ensure STRICT_ALIGN_SIZE is at least page aligned
+    - powerpc/vmlinux.lds: Add an explicit symbol for the SRWX boundary
+    - powerpc/64s/radix: Fix crash with unaligned relocated kernel
+    - powerpc/64s/radix: Fix RWX mapping with relocated kernel
+    - drm/i915/gvt: fix double free bug in split_2MB_gtt_entry
+    - uaccess: Add speculation barrier to copy_from_user()
+    - binder: read pre-translated fds from sender buffer
+    - binder: defer copies of pre-patched txn data
+    - binder: fix pointer cast warning
+    - binder: Address corner cases in deferred copy and fixup
+    - binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0
+    - nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
+    - wifi: mwifiex: Add missing compatible string for SD8787
+    - audit: update the mailing list in MAINTAINERS
+    - ext4: Fix function prototype mismatch for ext4_feat_ktype
+    - bpf: add missing header file include
+    - Linux 5.15.96
+  * Debian autoreconstruct Fix restoration of execute permissions (LP: #2015498)
+    - [Debian] autoreconstruct - fix restoration of execute permissions
+  * kernel: fix __clear_user() inline assembly constraints (LP: #2013088)
+    - s390/uaccess: add missing earlyclobber annotations to __clear_user()
+  * Kernel crash during Mellanox performance testing (LP: #2015097)
+    - net/mlx5: fs, refactor software deletion rule
+  * expoline.o is packaged unconditionally for s390x (LP: #2013209)
+    - [Packaging] Copy expoline.o only when produced by the build
+  * Intel E810 NICs driver in causing hangs when booting and bonds configured
+    (LP: #2004262)
+    - ice: avoid bonding causing auxiliary plug/unplug under RTNL lock
+  * Jammy update: v5.15.95 upstream stable release (LP: #2013118)
+    - mptcp: fix locking for in-kernel listener creation
+    - kprobes: treewide: Cleanup the error messages for kprobes
+    - riscv: kprobe: Fixup misaligned load text
+    - ACPI / x86: Add support for LPS0 callback handler
+    - ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
+    - ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
+    - selftests/bpf: Verify copy_register_state() preserves parent/live fields
+    - ALSA: hda: Do not unset preset when cleaning up codec
+    - bpf, sockmap: Don't let sock_map_{close,destroy,unhash} call itself
+    - ASoC: cs42l56: fix DT probe
+    - tools/virtio: fix the vringh test for virtio ring changes
+    - net/rose: Fix to not accept on connected socket
+    - net: stmmac: do not stop RX_CLK in Rx LPI state for qcs404 SoC
+    - drm/nouveau/devinit/tu102-: wait for GFW_BOOT_PROGRESS == COMPLETED
+    - net: sched: sch: Bounds check priority
+    - s390/decompressor: specify __decompress() buf len to avoid overflow
+    - nvme-fc: fix a missing queue put in nvmet_fc_ls_create_association
+    - drm/amd/display: Properly handle additional cases where DCN is not supported
+    - platform/x86: touchscreen_dmi: Add Chuwi Vi8 (CWI501) DMI match
+    - nvmem: core: add error handling for dev_set_name
+    - nvmem: core: fix cleanup after dev_set_name()
+    - nvmem: core: fix registration vs use race
+    - nvmem: core: fix return value
+    - xfs: zero inode fork buffer at allocation
+    - xfs: fix potential log item leak
+    - xfs: detect self referencing btree sibling pointers
+    - xfs: set XFS_FEAT_NLINK correctly
+    - xfs: validate v5 feature fields
+    - xfs: avoid unnecessary runtime sibling pointer endian conversions
+    - xfs: don't assert fail on perag references on teardown
+    - xfs: assert in xfs_btree_del_cursor should take into account error
+    - xfs: purge dquots after inode walk fails during quotacheck
+    - xfs: don't leak btree cursor when insrec fails after a split
+    - mptcp: do not wait for bare sockets' timeout
+    - aio: fix mremap after fork null-deref
+    - drm/amd/display: Fail atomic_check early on normalize_zpos error
+    - platform/x86: amd-pmc: Fix compilation when CONFIG_DEBUGFS is disabled
+    - platform/x86: amd-pmc: Correct usage of SMU version
+    - platform/x86/amd: pmc: Disable IRQ1 wakeup for RN/CZN
+    - netfilter: nft_tproxy: restrict to prerouting hook
+    - tcp: Fix listen() regression in 5.15.88.
+    - mmc: jz4740: Work around bug on JZ4760(B)
+    - mmc: sdio: fix possible resource leaks in some error paths
+    - mmc: mmc_spi: fix error handling in mmc_spi_probe()
+    - ALSA: hda/conexant: add a new hda codec SN6180
+    - ALSA: hda/realtek - fixed wrong gpio assigned
+    - sched/psi: Fix use-after-free in ep_remove_wait_queue()
+    - hugetlb: check for undefined shift on 32 bit architectures
+    - of: reserved_mem: Have kmemleak ignore dynamically allocated reserved mem
+    - selftest/lkdtm: Skip stack-entropy test if lkdtm is not available
+    - net: Fix unwanted sign extension in netdev_stats_to_stats64()
+    - revert "squashfs: harden sanity check in squashfs_read_xattr_id_table"
+    - ixgbe: allow to increase MTU to 3K with XDP enabled
+    - i40e: add double of VLAN header when computing the max MTU
+    - net: bgmac: fix BCM5358 support by setting correct flags
+    - net: ethernet: ti: am65-cpsw: Add RX DMA Channel Teardown Quirk
+    - sctp: sctp_sock_filter(): avoid list_entry() on possibly empty list
+    - dccp/tcp: Avoid negative sk_forward_alloc by ipv6_pinfo.pktoptions.
+    - net/usb: kalmia: Don't pass act_len in usb_bulk_msg error path
+    - net: openvswitch: fix possible memory leak in ovs_meter_cmd_set()
+    - net: stmmac: fix order of dwmac5 FlexPPS parametrization sequence
+    - bnxt_en: Fix mqprio and XDP ring checking logic
+    - net: stmmac: Restrict warning on disabling DMA store and fwd mode
+    - ixgbe: add double of VLAN header when computing the max MTU
+    - ipv6: Fix datagram socket connection with DSCP.
+    - ipv6: Fix tcp socket connection with DSCP.
+    - nilfs2: fix underflow in second superblock position calculations
+    - mm/filemap: fix page end in filemap_get_read_batch
+    - drm/i915/gen11: Moving WAs to icl_gt_workarounds_init()
+    - drm/i915/gen11: Wa_1408615072/Wa_1407596294 should be on GT list
+    - flow_offload: fill flags to action structure
+    - net/sched: act_ctinfo: use percpu stats
+    - i40e: Add checking for null for nlmsg_find_attr()
+    - kvm: initialize all of the kvm_debugregs structure before sending it to
+      userspace
+    - alarmtimer: Prevent starvation by small intervals and SIG_IGN
+    - ASoC: SOF: Intel: hda-dai: fix possible stream_tag leak
+    - net: sched: sch: Fix off by one in htb_activate_prios()
+    - platform/x86/amd: pmc: add CONFIG_SERIO dependency
+    - Linux 5.15.95
+  * CVE-2023-1075
+    - net/tls: tls_is_tx_ready() checked list_entry
+  * devlink_port_split from ubuntu_kernel_selftests.net fails on hirsute
+    (KeyError: 'flavour') (LP: #1937133)
+    - selftests: net: devlink_port_split.py: skip test if no suitable device
+      available
+  * Connection timeout due to conntrack limits (LP: #2011616)
+    - netfilter: conntrack: adopt safer max chain length
+  * Jammy update: v5.15.94 upstream stable release (LP: #2012673)
+    - mm/migration: return errno when isolate_huge_page failed
+    - migrate: hugetlb: check for hugetlb shared PMD in node migration
+    - btrfs: limit device extents to the device size
+    - btrfs: zlib: zero-initialize zlib workspace
+    - ALSA: hda/realtek: Add Positivo N14KP6-TG
+    - ALSA: emux: Avoid potential array out-of-bound in snd_emux_xg_control()
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro 360
+    - ALSA: hda/realtek: Enable mute/micmute LEDs on HP Elitebook, 645 G9
+    - tracing: Fix poll() and select() do not work on per_cpu trace_pipe and
+      trace_pipe_raw
+    - of/address: Return an error when no valid dma-ranges are found
+    - can: j1939: do not wait 250 ms if the same addr was already claimed
+    - xfrm: compat: change expression for switch in xfrm_xlate64
+    - IB/hfi1: Restore allocated resources on failed copyout
+    - xfrm/compat: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
+    - IB/IPoIB: Fix legacy IPoIB due to wrong number of queues
+    - RDMA/irdma: Fix potential NULL-ptr-dereference
+    - RDMA/usnic: use iommu_map_atomic() under spin_lock()
+    - xfrm: fix bug with DSCP copy to v6 from v4 tunnel
+    - net: phylink: move phy_device_free() to correctly release phy device
+    - bonding: fix error checking in bond_debug_reregister()
+    - net: phy: meson-gxl: use MMD access dummy stubs for GXL, internal PHY
+    - ionic: clean interrupt before enabling queue to avoid credit race
+    - uapi: add missing ip/ipv6 header dependencies for linux/stddef.h
+    - ice: Do not use WQ_MEM_RECLAIM flag for workqueue
+    - net: dsa: mt7530: don't change PVC_EG_TAG when CPU port becomes VLAN-aware
+    - net: mscc: ocelot: fix VCAP filters not matching on MAC with "protocol
+      802.1Q"
+    - net/mlx5e: Move repeating clear_bit in mlx5e_rx_reporter_err_rq_cqe_recover
+    - net/mlx5e: Introduce the mlx5e_flush_rq function
+    - net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
+    - net/mlx5: Bridge, fix ageing of peer FDB entries
+    - net/mlx5e: IPoIB, Show unknown speed instead of error
+    - net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
+    - net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
+    - net/mlx5: Serialize module cleanup with reload and remove
+    - igc: Add ndo_tx_timeout support
+    - rds: rds_rm_zerocopy_callback() use list_first_entry()
+    - selftests: forwarding: lib: quote the sysctl values
+    - ALSA: pci: lx6464es: fix a debug loop
+    - riscv: stacktrace: Fix missing the first frame
+    - ASoC: topology: Return -ENOMEM on memory allocation failure
+    - pinctrl: mediatek: Fix the drive register definition of some Pins
+    - pinctrl: aspeed: Fix confusing types in return value
+    - pinctrl: single: fix potential NULL dereference
+    - spi: dw: Fix wrong FIFO level setting for long xfers
+    - pinctrl: intel: Restore the pins that used to be in Direct IRQ mode
+    - cifs: Fix use-after-free in rdata->read_into_pages()
+    - net: USB: Fix wrong-direction WARNING in plusb.c
+    - mptcp: be careful on subflow status propagation on errors
+    - btrfs: free device in btrfs_close_devices for a single device filesystem
+    - usb: core: add quirk for Alcor Link AK9563 smartcard reader
+    - usb: typec: altmodes/displayport: Fix probe pin assign check
+    - clk: ingenic: jz4760: Update M/N/OD calculation algorithm
+    - ceph: flush cap releases when the session is flushed
+    - riscv: Fixup race condition on PG_dcache_clean in flush_icache_pte
+    - powerpc/64s/interrupt: Fix interrupt exit race with security mitigation
+      switch
+    - rtmutex: Ensure that the top waiter is always woken up
+    - arm64: dts: meson-gx: Make mmc host controller interrupts level-sensitive
+    - arm64: dts: meson-g12-common: Make mmc host controller interrupts level-
+      sensitive
+    - arm64: dts: meson-axg: Make mmc host controller interrupts level-sensitive
+    - Fix page corruption caused by racy check in __free_pages
+    - drm/amdgpu/fence: Fix oops due to non-matching drm_sched init/fini
+    - drm/i915: Initialize the obj flags for shmem objects
+    - drm/i915: Fix VBT DSI DVO port handling
+    - x86/speculation: Identify processors vulnerable to SMT RSB predictions
+    - KVM: x86: Mitigate the cross-thread return address predictions bug
+    - Documentation/hw-vuln: Add documentation for Cross-Thread Return Predictions
+    - Linux 5.15.94
+  * Jammy update: v5.15.93 upstream stable release (LP: #2012665)
+    - firewire: fix memory leak for payload of request subaction to IEC 61883-1
+      FCP region
+    - bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()
+    - ASoC: Intel: boards: fix spelling in comments
+    - ASoC: Intel: bytcht_es8316: move comment to the right place
+    - ASoC: Intel: bytcht_es8316: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_rt5651: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_rt5640: Drop reference count of ACPI device after use
+    - ASoC: Intel: bytcr_wm5102: Drop reference count of ACPI device after use
+    - bpf: Fix a possible task gone issue with bpf_send_signal[_thread]() helpers
+    - ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
+    - bpf: Support <8-byte scalar spill and refill
+    - bpf: Fix to preserve reg parent/live fields when copying range info
+    - bpf, sockmap: Check for any of tcp_bpf_prots when cloning a listener
+    - arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
+    - drm/vc4: hdmi: make CEC adapter name unique
+    - scsi: Revert "scsi: core: map PQ=1, PDT=other values to
+      SCSI_SCAN_TARGET_PRESENT"
+    - vhost/net: Clear the pending messages when the backend is removed
+    - WRITE is "data source", not destination...
+    - READ is "data destination", not source...
+    - fix iov_iter_bvec() "direction" argument
+    - fix "direction" argument of iov_iter_kvec()
+    - ice: Prevent set_channel from changing queues while RDMA active
+    - qede: execute xdp_do_flush() before napi_complete_done()
+    - virtio-net: execute xdp_do_flush() before napi_complete_done()
+    - dpaa_eth: execute xdp_do_flush() before napi_complete_done()
+    - dpaa2-eth: execute xdp_do_flush() before napi_complete_done()
+    - sfc: correctly advertise tunneled IPv6 segmentation
+    - net: phy: dp83822: Fix null pointer access on DP83825/DP83826 devices
+    - block/bfq-iosched.c: use "false" rather than "BLK_RW_ASYNC"
+    - block, bfq: replace 0/1 with false/true in bic apis
+    - block, bfq: fix uaf for bfqq in bic_set_bfqq()
+    - netrom: Fix use-after-free caused by accept on already connected socket
+    - drm/i915/guc: Fix locking when searching for a hung request
+    - drm/i915/adlp: Fix typo for reference clock
+    - netfilter: br_netfilter: disable sabotage_in hook after first suppression
+    - squashfs: harden sanity check in squashfs_read_xattr_id_table
+    - net: phy: meson-gxl: Add generic dummy stubs for MMD register access
+    - ip/ip6_gre: Fix changing addr gen mode not generating IPv6 link local
+      address
+    - ip/ip6_gre: Fix non-point-to-point tunnel not generating IPv6 link local
+      address
+    - riscv: kprobe: Fixup kernel panic when probing an illegal position
+    - igc: return an error if the mac type is unknown in
+      igc_ptp_systim_to_hwtstamp()
+    - can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
+    - ata: libata: Fix sata_down_spd_limit() when no link speed is reported
+    - selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
+    - selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
+    - selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy
+      benchmarking
+    - virtio-net: Keep stop() to follow mirror sequence of open()
+    - net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
+    - efi: fix potential NULL deref in efi_mem_reserve_persistent
+    - i2c: designware-pci: Add new PCI IDs for AMD NAVI GPU
+    - i2c: mxs: suppress probe-deferral error message
+    - scsi: target: core: Fix warning on RT kernels
+    - perf/x86/intel: Add Emerald Rapids
+    - scsi: iscsi_tcp: Fix UAF during logout when accessing the shost ipaddress
+    - scsi: iscsi_tcp: Fix UAF during login when accessing the shost ipaddress
+    - i2c: rk3x: fix a bunch of kernel-doc warnings
+    - platform/x86: gigabyte-wmi: add support for B450M DS3H WIFI-CF
+    - net/x25: Fix to not accept on connected socket
+    - drm/amd/display: Fix timing not changning when freesync video is enabled
+    - iio: adc: stm32-dfsdm: fill module aliases
+    - usb: dwc3: qcom: enable vbus override when in OTG dr-mode
+    - usb: gadget: f_fs: Fix unbalanced spinlock in __ffs_ep0_queue_wait
+    - vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF
+    - Input: i8042 - add Clevo PCX0DX to i8042 quirk table
+    - fbcon: Check font dimension limits
+    - net: qrtr: free memory on error path in radix_tree_insert()
+    - watchdog: diag288_wdt: do not use stack buffers for hardware data
+    - watchdog: diag288_wdt: fix __diag288() inline assembly
+    - ALSA: hda/realtek: Add Acer Predator PH315-54
+    - efi: Accept version 2 of memory attributes table
+    - iio: hid: fix the retval in accel_3d_capture_sample
+    - iio: hid: fix the retval in gyro_3d_capture_sample
+    - iio: adc: berlin2-adc: Add missing of_node_put() in error path
+    - iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
+    - iio: imu: fxos8700: fix ACCEL measurement range selection
+    - iio: imu: fxos8700: fix incomplete ACCEL and MAGN channels readback
+    - iio: imu: fxos8700: fix IMU data bits returned to user space
+    - iio: imu: fxos8700: fix map label of channel type to MAGN sensor
+    - iio: imu: fxos8700: fix swapped ACCEL and MAGN channels readback
+    - iio: imu: fxos8700: fix incorrect ODR mode readback
+    - iio: imu: fxos8700: fix failed initialization ODR mode assignment
+    - iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
+    - iio: imu: fxos8700: fix MAGN sensor scale and unit
+    - nvmem: qcom-spmi-sdam: fix module autoloading
+    - parisc: Fix return code of pdc_iodc_print()
+    - parisc: Wire up PTRACE_GETREGS/PTRACE_SETREGS for compat case
+    - riscv: disable generation of unwind tables
+    - mm: hugetlb: proc: check for hugetlb shared PMD in /proc/PID/smaps
+    - usb: gadget: f_uac2: Fix incorrect increment of bNumEndpoints
+    - kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
+    - x86/debug: Fix stack recursion caused by wrongly ordered DR7 accesses
+    - fpga: stratix10-soc: Fix return value check in s10_ops_write_init()
+    - mm/swapfile: add cond_resched() in get_swap_pages()
+    - highmem: round down the address passed to kunmap_flush_on_unmap()
+    - Squashfs: fix handling and sanity checking of xattr_ids count
+    - drm/i915: Fix potential bit_17 double-free
+    - nvmem: core: initialise nvmem->id early
+    - nvmem: core: remove nvmem_config wp_gpio
+    - nvmem: core: fix cell removal on error
+    - serial: 8250_dma: Fix DMA Rx completion race
+    - serial: 8250_dma: Fix DMA Rx rearm race
+    - phy: qcom-qmp-combo: disable runtime PM on unbind
+    - phy: qcom-qmp-combo: fix memleak on probe deferral
+    - phy: qcom-qmp-usb: fix memleak on probe deferral
+    - phy: qcom-qmp-combo: fix broken power on
+    - phy: qcom-qmp-combo: fix runtime suspend
+    - bpf: Fix incorrect state pruning for <8B spill/fill
+    - bpf: Do not reject when the stack read size is different from the tracked
+      scalar size
+    - iio:adc:twl6030: Enable measurement of VAC
+    - powerpc/imc-pmu: Revert nest_init_lock to being a mutex
+    - fs/ntfs3: Validate attribute data and valid sizes
+    - ovl: Use "buf" flexible array for memcpy() destination
+    - fbdev: smscufx: fix error handling code in ufx_usb_probe
+    - f2fs: fix to do sanity check on i_extra_isize in is_alive()
+    - wifi: brcmfmac: Check the count value of channel spec to prevent out-of-
+      bounds reads
+    - gfs2: Cosmetic gfs2_dinode_{in,out} cleanup
+    - gfs2: Always check inode size of inline inodes
+    - bpf: Skip invalid kfunc call in backtrack_insn
+    - Linux 5.15.93
+  * CVE-2023-1118
+    - media: rc: Fix use-after-free bugs caused by ene_tx_irqsim()
+  * [SRU][Ubuntu 22.04.1]: Observed "Array Index out of bounds" Call Trace
+    multiple times on Ubuntu 22.04.1 OS during boot (LP: #2008157)
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_FW_RAID_MAP
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_FW_RAID_MAP_DYNAMIC
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_DRV_RAID_MAP
+    - scsi: megaraid_sas: Replace one-element array with flexible-array member in
+      MR_PD_CFG_SEQ_NUM_SYNC
+    - scsi: megaraid_sas: Use struct_size() in code related to struct
+      MR_FW_RAID_MAP
+    - scsi: megaraid_sas: Use struct_size() in code related to struct
+      MR_PD_CFG_SEQ_NUM_SYNC
+  * Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo
+    child qdiscs" (LP: #2011926)
+    - Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo
+      child qdiscs"
+
+  [ Ubuntu: 5.15.0-71.78 ]
+
+  * jammy/linux: 5.15.0-71.78 -proposed tracker (LP: #2016820)
+  * CVE-2023-1872
+    - io_uring: add missing lock in io_get_file_fixed
+    - io_uring: ensure that io_init_req() passes in the right issue_flags
+  * CVE-2023-1829
+    - net/sched: Retire tcindex classifier
+    - [Config]: Make sure CONFIG_NET_CLS_TCINDEX is not available
+
+ -- Masahiro Yamada <masahiro.yamada@canonical.com>  Fri, 19 May 2023 17:01:57 +0900
+
+linux-xilinx-zynqmp (5.15.0-1021.25) jammy; urgency=medium
+
+  * jammy/linux-xilinx-zynqmp: 5.15.0-1021.25 -proposed tracker (LP: #2008753)
+
+  * Jammy update: v5.15.81 upstream stable release (LP: #2003130)
+    - [Config] updateconfigs for CC_HAS_ASM_GOTO_TIED_OUTPUT
+    - [Config] updateconfigs for INET_TABLE_PERTURB_ORDER
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] remove unneeded packqages
+
+  [ Ubuntu: 5.15.0-70.77 ]
+
+  * jammy/linux: 5.15.0-70.77 -proposed tracker (LP: #2011918)
+  * CVE-2023-26545
+    - net: mpls: fix stale pointer if allocation fails during device rename
+  * CVE-2023-1281
+    - net/sched: tcindex: update imperfect hash filters respecting rcu
+  * [SRU][Ubuntu 22.04.1] mpi3mr: Add management application interface(BSG)
+    support (LP: #1971151)
+    - scsi: mpi3mr: Add bsg device support
+    - scsi: mpi3mr: Add support for driver commands
+    - scsi: mpi3mr: Move data structures/definitions from MPI headers to uapi
+      header
+    - scsi: mpi3mr: Add support for MPT commands
+    - scsi: mpi3mr: Add support for PEL commands
+    - scsi: mpi3mr: Expose adapter state to sysfs
+    - scsi: mpi3mr: Add support for NVMe passthrough
+    - scsi: mpi3mr: Update driver version to 8.0.0.69.0
+    - scsi: mpi3mr: Increase I/O timeout value to 60s
+    - scsi: mpi3mr: Hidden drives not removed during soft reset
+    - scsi: mpi3mr: Return I/Os to an unrecoverable HBA with DID_ERROR
+    - scsi: mpi3mr: Fix a NULL vs IS_ERR() bug in mpi3mr_bsg_init()
+    - scsi: mpi3mr: Return error if dma_alloc_coherent() fails
+    - scsi: mpi3mr: Add shost related sysfs attributes
+    - scsi: mpi3mr: Add target device related sysfs attributes
+    - scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
+    - scsi: mpi3mr: Fix kernel-doc
+  * cpufreq: intel_pstate: Update Balance performance EPP for Sapphire Rapids
+    (LP: #2008519)
+    - cpufreq: intel_pstate: Update EPP for AlderLake mobile
+    - cpufreq: intel_pstate: Adjust balance_performance EPP for Sapphire Rapids
+  * Fail to output sound to external monitor which connects via docking station
+    (LP: #2009024)
+    - [Config] Enable CONFIG_SND_HDA_INTEL_HDMI_SILENT_STREAM
+  * Fix mediatek wifi driver crash when loading wrong SAR table (LP: #2009118)
+    - wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
+  * Jammy update: v5.15.92 upstream stable release (LP: #2011472)
+    - ARM: dts: imx: Fix pca9547 i2c-mux node name
+    - ARM: dts: vf610: Fix pca9548 i2c-mux node names
+    - arm64: dts: freescale: Fix pca954x i2c-mux node names
+    - arm64: dts: imx8mq-thor96: fix no-mmc property for SDHCI
+    - firmware: arm_scmi: Clear stale xfer->hdr.status
+    - bpf: Skip task with pid=1 in send_signal_common()
+    - erofs/zmap.c: Fix incorrect offset calculation
+    - blk-cgroup: fix missing pd_online_fn() while activating policy
+    - HID: playstation: sanity check DualSense calibration data.
+    - dmaengine: imx-sdma: Fix a possible memory leak in sdma_transfer_init
+    - cifs: fix return of uninitialized rc in dfs_cache_update_tgthint()
+    - extcon: usbc-tusb320: fix kernel-doc warning
+    - Bluetooth: fix null ptr deref on hci_sync_conn_complete_evt
+    - tools: fix ARRAY_SIZE defines in tools and selftests hdrs
+    - selftests/vm: remove ARRAY_SIZE define from individual tests
+    - selftests: Provide local define of __cpuid_count()
+    - net: fix NULL pointer in skb_segment_list
+    - net: mctp: purge receive queues on sk destruction
+    - Linux 5.15.92
+  * Jammy update: v5.15.91 upstream stable release (LP: #2011467)
+    - memory: tegra: Remove clients SID override programming
+    - memory: atmel-sdramc: Fix missing clk_disable_unprepare in
+      atmel_ramc_probe()
+    - memory: mvebu-devbus: Fix missing clk_disable_unprepare in
+      mvebu_devbus_probe()
+    - dmaengine: ti: k3-udma: Do conditional decrement of
+      UDMA_CHAN_RT_PEER_BCNT_REG
+    - arm64: dts: imx8mp-phycore-som: Remove invalid PMIC property
+    - ARM: dts: imx6ul-pico-dwarf: Use 'clock-frequency'
+    - ARM: dts: imx7d-pico: Use 'clock-frequency'
+    - ARM: dts: imx6qdl-gw560x: Remove incorrect 'uart-has-rtscts'
+    - arm64: dts: imx8mm-beacon: Fix ecspi2 pinmux
+    - ARM: imx: add missing of_node_put()
+    - HID: intel_ish-hid: Add check for ishtp_dma_tx_map
+    - arm64: dts: imx8mm-venice-gw7901: fix USB2 controller OC polarity
+    - soc: imx8m: Fix incorrect check for of_clk_get_by_name()
+    - reset: uniphier-glue: Use reset_control_bulk API
+    - reset: uniphier-glue: Fix possible null-ptr-deref
+    - EDAC/highbank: Fix memory leak in highbank_mc_probe()
+    - firmware: arm_scmi: Harden shared memory access in fetch_response
+    - firmware: arm_scmi: Harden shared memory access in fetch_notification
+    - tomoyo: fix broken dependency on *.conf.default
+    - RDMA/core: Fix ib block iterator counter overflow
+    - IB/hfi1: Reject a zero-length user expected buffer
+    - IB/hfi1: Reserve user expected TIDs
+    - IB/hfi1: Fix expected receive setup error exit issues
+    - IB/hfi1: Immediately remove invalid memory from hardware
+    - IB/hfi1: Remove user expected buffer invalidate race
+    - affs: initialize fsdata in affs_truncate()
+    - PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
+    - arm64: dts: qcom: msm8992: Don't use sfpb mutex
+    - arm64: dts: qcom: msm8992-libra: Add CPU regulators
+    - arm64: dts: qcom: msm8992-libra: Fix the memory map
+    - phy: ti: fix Kconfig warning and operator precedence
+    - NFSD: fix use-after-free in nfsd4_ssc_setup_dul()
+    - ARM: dts: at91: sam9x60: fix the ddr clock for sam9x60
+    - amd-xgbe: TX Flow Ctrl Registers are h/w ver dependent
+    - amd-xgbe: Delay AN timeout during KR training
+    - bpf: Fix pointer-leak due to insufficient speculative store bypass
+      mitigation
+    - phy: rockchip-inno-usb2: Fix missing clk_disable_unprepare() in
+      rockchip_usb2phy_power_on()
+    - net: nfc: Fix use-after-free in local_cleanup()
+    - net: wan: Add checks for NULL for utdm in undo_uhdlc_init and unmap_si_regs
+    - net: enetc: avoid deadlock in enetc_tx_onestep_tstamp()
+    - sch_htb: Avoid grafting on htb_destroy_class_offload when destroying htb
+    - gpio: use raw spinlock for gpio chip shadowed data
+    - gpio: mxc: Protect GPIO irqchip RMW with bgpio spinlock
+    - gpio: mxc: Always set GPIOs used as interrupt source to INPUT mode
+    - pinctrl/rockchip: Use temporary variable for struct device
+    - pinctrl/rockchip: add error handling for pull/drive register getters
+    - pinctrl: rockchip: fix reading pull type on rk3568
+    - net: stmmac: Fix queue statistics reading
+    - net/sched: sch_taprio: fix possible use-after-free
+    - l2tp: Serialize access to sk_user_data with sk_callback_lock
+    - l2tp: Don't sleep and disable BH under writer-side sk_callback_lock
+    - l2tp: convert l2tp_tunnel_list to idr
+    - l2tp: close all race conditions in l2tp_tunnel_register()
+    - octeontx2-pf: Avoid use of GFP_KERNEL in atomic context
+    - net: usb: sr9700: Handle negative len
+    - net: mdio: validate parameter addr in mdiobus_get_phy()
+    - HID: check empty report_list in hid_validate_values()
+    - HID: check empty report_list in bigben_probe()
+    - net: stmmac: fix invalid call to mdiobus_get_phy()
+    - pinctrl: rockchip: fix mux route data for rk3568
+    - HID: revert CHERRY_MOUSE_000C quirk
+    - usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait
+    - usb: gadget: f_fs: Ensure ep0req is dequeued before free_request
+    - Bluetooth: Fix possible deadlock in rfcomm_sk_state_change
+    - net: ipa: disable ipa interrupt during suspend
+    - net/mlx5: E-switch, Fix setting of reserved fields on
+      MODIFY_SCHEDULING_ELEMENT
+    - net: mlx5: eliminate anonymous module_init & module_exit
+    - drm/panfrost: fix GENERIC_ATOMIC64 dependency
+    - dmaengine: Fix double increment of client_count in dma_chan_get()
+    - net: macb: fix PTP TX timestamp failure due to packet padding
+    - virtio-net: correctly enable callback during start_xmit
+    - l2tp: prevent lockdep issue in l2tp_tunnel_register()
+    - HID: betop: check shape of output reports
+    - cifs: fix potential deadlock in cache_refresh_path()
+    - dmaengine: xilinx_dma: call of_node_put() when breaking out of
+      for_each_child_of_node()
+    - phy: phy-can-transceiver: Skip warning if no "max-bitrate"
+    - drm/amd/display: fix issues with driver unload
+    - nvme-pci: fix timeout request state check
+    - tcp: avoid the lookup process failing to get sk in ehash table
+    - octeontx2-pf: Fix the use of GFP_KERNEL in atomic context on rt
+    - ptdma: pt_core_execute_cmd() should use spinlock
+    - device property: fix of node refcount leak in
+      fwnode_graph_get_next_endpoint()
+    - w1: fix deadloop in __w1_remove_master_device()
+    - w1: fix WARNING after calling w1_process()
+    - driver core: Fix test_async_probe_init saves device in wrong array
+    - selftests/net: toeplitz: fix race on tpacket_v3 block close
+    - net: dsa: microchip: ksz9477: port map correction in ALU table entry
+      register
+    - thermal/core: Remove duplicate information when an error occurs
+    - thermal/core: Rename 'trips' to 'num_trips'
+    - thermal: Validate new state in cur_state_store()
+    - thermal/core: fix error code in __thermal_cooling_device_register()
+    - thermal: core: call put_device() only after device_register() fails
+    - net: stmmac: enable all safety features by default
+    - tcp: fix rate_app_limited to default to 1
+    - scsi: iscsi: Fix multiple iSCSI session unbind events sent to userspace
+    - cpufreq: Add Tegra234 to cpufreq-dt-platdev blocklist
+    - kcsan: test: don't put the expect array on the stack
+    - cpufreq: Add SM6375 to cpufreq-dt-platdev blocklist
+    - ASoC: fsl_micfil: Correct the number of steps on SX controls
+    - net: usb: cdc_ether: add support for Thales Cinterion PLS62-W modem
+    - drm: Add orientation quirk for Lenovo ideapad D330-10IGL
+    - s390/debug: add _ASM_S390_ prefix to header guard
+    - s390: expicitly align _edata and _end symbols on page boundary
+    - perf/x86/msr: Add Emerald Rapids
+    - perf/x86/intel/uncore: Add Emerald Rapids
+    - cpufreq: armada-37xx: stop using 0 as NULL pointer
+    - ASoC: fsl_ssi: Rename AC'97 streams to avoid collisions with AC'97 CODEC
+    - ASoC: fsl-asoc-card: Fix naming of AC'97 CODEC widgets
+    - spi: spidev: remove debug messages that access spidev->spi without locking
+    - KVM: s390: interrupt: use READ_ONCE() before cmpxchg()
+    - scsi: hisi_sas: Set a port invalid only if there are no devices attached
+      when refreshing port id
+    - r8152: add vendor/device ID pair for Microsoft Devkit
+    - platform/x86: touchscreen_dmi: Add info for the CSL Panther Tab HD
+    - platform/x86: asus-nb-wmi: Add alternate mapping for KEY_SCREENLOCK
+    - lockref: stop doing cpu_relax in the cmpxchg loop
+    - firmware: coreboot: Check size of table entry and use flex-array
+    - drm/i915: Allow switching away via vga-switcheroo if uninitialized
+    - drm/i915: Remove unused variable
+    - x86: ACPI: cstate: Optimize C3 entry on AMD CPUs
+    - fs: reiserfs: remove useless new_opts in reiserfs_remount
+    - sysctl: add a new register_sysctl_init() interface
+    - kernel/panic: move panic sysctls to its own file
+    - panic: unset panic_on_warn inside panic()
+    - ubsan: no need to unset panic_on_warn in ubsan_epilogue()
+    - kasan: no need to unset panic_on_warn in end_report()
+    - exit: Add and use make_task_dead.
+    - objtool: Add a missing comma to avoid string concatenation
+    - hexagon: Fix function name in die()
+    - h8300: Fix build errors from do_exit() to make_task_dead() transition
+    - csky: Fix function name in csky_alignment() and die()
+    - ia64: make IA64_MCA_RECOVERY bool instead of tristate
+    - panic: Separate sysctl logic from CONFIG_SMP
+    - exit: Put an upper limit on how often we can oops
+    - exit: Expose "oops_count" to sysfs
+    - exit: Allow oops_limit to be disabled
+    - panic: Consolidate open-coded panic_on_warn checks
+    - panic: Introduce warn_limit
+    - panic: Expose "warn_count" to sysfs
+    - docs: Fix path paste-o for /sys/kernel/warn_count
+    - exit: Use READ_ONCE() for all oops/warn limit reads
+    - Bluetooth: hci_sync: cancel cmd_timer if hci_open failed
+    - drm/amdgpu: complete gfxoff allow signal during suspend without delay
+    - scsi: hpsa: Fix allocation size for scsi_host_alloc()
+    - KVM: SVM: fix tsc scaling cache logic
+    - module: Don't wait for GOING modules
+    - tracing: Make sure trace_printk() can output as soon as it can be used
+    - trace_events_hist: add check for return value of 'create_hist_field'
+    - ftrace/scripts: Update the instructions for ftrace-bisect.sh
+    - cifs: Fix oops due to uncleared server->smbd_conn in reconnect
+    - i2c: mv64xxx: Remove shutdown method from driver
+    - i2c: mv64xxx: Add atomic_xfer method to driver
+    - ksmbd: add smbd max io size parameter
+    - ksmbd: add max connections parameter
+    - ksmbd: do not sign response to session request for guest login
+    - ksmbd: downgrade ndr version error message to debug
+    - ksmbd: limit pdu length size according to connection status
+    - ovl: fail on invalid uid/gid mapping at copy up
+    - KVM: x86/vmx: Do not skip segment attributes if unusable bit is set
+    - KVM: arm64: GICv4.1: Fix race with doorbell on VPE activation/deactivation
+    - thermal: intel: int340x: Protect trip temperature from concurrent updates
+    - ipv6: fix reachability confirmation with proxy_ndp
+    - ARM: 9280/1: mm: fix warning on phys_addr_t to void pointer assignment
+    - EDAC/device: Respect any driver-supplied workqueue polling value
+    - EDAC/qcom: Do not pass llcc_driv_data as edac_device_ctl_info's pvt_info
+    - net: mana: Fix IRQ name - add PCI and queue number
+    - scsi: ufs: core: Fix devfreq deadlocks
+    - i2c: designware: use casting of u64 in clock multiplication to avoid
+      overflow
+    - netlink: prevent potential spectre v1 gadgets
+    - net: fix UaF in netns ops registration error path
+    - drm/i915/selftest: fix intel_selftest_modify_policy argument types
+    - netfilter: nft_set_rbtree: Switch to node list walk for overlap detection
+    - netfilter: nft_set_rbtree: skip elements in transaction from garbage
+      collection
+    - netlink: annotate data races around nlk->portid
+    - netlink: annotate data races around dst_portid and dst_group
+    - netlink: annotate data races around sk_state
+    - ipv4: prevent potential spectre v1 gadget in ip_metrics_convert()
+    - ipv4: prevent potential spectre v1 gadget in fib_metrics_match()
+    - netfilter: conntrack: fix vtag checks for ABORT/SHUTDOWN_COMPLETE
+    - netrom: Fix use-after-free of a listening socket.
+    - net/sched: sch_taprio: do not schedule in taprio_reset()
+    - sctp: fail if no bound addresses can be used for a given scope
+    - riscv/kprobe: Fix instruction simulation of JALR
+    - nvme: fix passthrough csi check
+    - gpio: mxc: Unlock on error path in mxc_flip_edge()
+    - ravb: Rename "no_ptp_cfg_active" and "ptp_cfg_active" variables
+    - net: ravb: Fix lack of register setting after system resumed for Gen3
+    - net: ravb: Fix possible hang if RIS2_QFF1 happen
+    - net: mctp: mark socks as dead on unhash, prevent re-add
+    - thermal: intel: int340x: Add locking to int340x_thermal_get_trip_type()
+    - net/tg3: resolve deadlock in tg3_reset_task() during EEH
+    - net: mdio-mux-meson-g12a: force internal PHY off on mux switch
+    - treewide: fix up files incorrectly marked executable
+    - tools: gpio: fix -c option of gpio-event-mon
+    - Revert "Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI
+      mode"
+    - cpufreq: Move to_gov_attr_set() to cpufreq.h
+    - cpufreq: governor: Use kobject release() method to free dbs_data
+    - kbuild: Allow kernel installation packaging to override pkg-config
+    - block: fix and cleanup bio_check_ro
+    - x86/i8259: Mark legacy PIC interrupts with IRQ_LEVEL
+    - netfilter: conntrack: unify established states for SCTP paths
+    - perf/x86/amd: fix potential integer overflow on shift of a int
+    - Linux 5.15.91
+  * Kernel livepatch support for for s390x (LP: #1639924)
+    - sched: Improve try_invoke_on_locked_down_task()
+    - sched,rcu: Rework try_invoke_on_locked_down_task()
+    - sched,livepatch: Use task_call_func()
+    - sched: Simplify wake_up_*idle*()
+    - sched,livepatch: Use wake_up_if_idle()
+    - sched: Improve wake_up_all_idle_cpus() take #2
+    - s390/entry: remove unused expoline thunk
+    - s390: remove unused expoline to BC instructions
+    - s390/nospec: generate single register thunks if possible
+    - s390/nospec: add an option to use thunk-extern
+    - s390/nospec: align and size extern thunks
+    - bug: Use normal relative pointers in 'struct bug_entry'
+    - s390/nospec: build expoline.o for modules_prepare target
+    - [Config] Enable EXPOLINE_EXTERN on s390x
+    - [Config] s390x: Removing UBSAN from configuration
+  * Do not sort the task scan result from /proc when synthesizing perf events
+    (LP: #2008971)
+    - perf synthetic-events: Don't sort the task scan result from /proc
+  * linux: Staging modules should be unsigned (LP: #1642368)
+    - [Packaging] Move and update signature inclusion list
+    - SAUCE: Add selective signing of staging modules
+    - [Packaging] Add module-signature-check
+    - [Packaging] module-signature-check: Check debian.<foo>/signature-inclusion
+    - [Packaging] Introduce debian/scripts/sign-module
+    - SAUCE: Switch to using debian/scripts/sign-module
+  * Jammy update: v5.15.90 upstream stable release (LP: #2008933)
+    - btrfs: fix trace event name typo for FLUSH_DELAYED_REFS
+    - pNFS/filelayout: Fix coalescing test for single DS
+    - tools/virtio: initialize spinlocks in vring_test.c
+    - virtio_pci: modify ENOENT to EINVAL
+    - vduse: Validate vq_num in vduse_validate_config()
+    - net/ethtool/ioctl: return -EOPNOTSUPP if we have no phy stats
+    - r8169: move rtl_wol_enable_rx() and rtl_prepare_power_down()
+    - RDMA/srp: Move large values to a new enum for gcc13
+    - btrfs: always report error in run_one_delayed_ref()
+    - x86/asm: Fix an assembler warning with current binutils
+    - f2fs: let's avoid panic if extent_tree is not created
+    - perf/x86/rapl: Treat Tigerlake like Icelake
+    - fbdev: omapfb: avoid stack overflow warning
+    - Bluetooth: hci_qca: Fix driver shutdown on closed serdev
+    - wifi: brcmfmac: fix regression for Broadcom PCIe wifi devices
+    - wifi: mac80211: sdata can be NULL during AMPDU start
+    - Add exception protection processing for vd in axi_chan_handle_err function
+    - zonefs: Detect append writes at invalid locations
+    - nilfs2: fix general protection fault in nilfs_btree_insert()
+    - efi: fix userspace infinite retry read efivars after EFI runtime services
+      page fault
+    - ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
+    - ALSA: hda/realtek: fix mute/micmute LEDs don't work for a HP platform
+    - drm/amdgpu: disable runtime pm on several sienna cichlid cards(v2)
+    - drm/amd: Delay removal of the firmware framebuffer
+    - hugetlb: unshare some PMDs when splitting VMAs
+    - io_uring: don't gate task_work run on TIF_NOTIFY_SIGNAL
+    - eventpoll: add EPOLL_URING_WAKE poll wakeup flag
+    - eventfd: provide a eventfd_signal_mask() helper
+    - io_uring: pass in EPOLL_URING_WAKE for eventfd signaling and wakeups
+    - io_uring: improve send/recv error handling
+    - io_uring: ensure recv and recvmsg handle MSG_WAITALL correctly
+    - io_uring: add flag for disabling provided buffer recycling
+    - io_uring: support MSG_WAITALL for IORING_OP_SEND(MSG)
+    - io_uring: allow re-poll if we made progress
+    - io_uring: fix async accept on O_NONBLOCK sockets
+    - io_uring: ensure that cached task references are always put on exit
+    - io_uring: remove duplicated calls to io_kiocb_ppos
+    - io_uring: update kiocb->ki_pos at execution time
+    - io_uring: do not recalculate ppos unnecessarily
+    - io_uring/rw: defer fsnotify calls to task context
+    - xhci-pci: set the dma max_seg_size
+    - usb: xhci: Check endpoint is valid before dereferencing it
+    - xhci: Fix null pointer dereference when host dies
+    - xhci: Add update_hub_device override for PCI xHCI hosts
+    - xhci: Add a flag to disable USB3 lpm on a xhci root port level.
+    - usb: acpi: add helper to check port lpm capability using acpi _DSM
+    - xhci: Detect lpm incapable xHC USB3 roothub ports from ACPI tables
+    - prlimit: do_prlimit needs to have a speculation check
+    - USB: serial: option: add Quectel EM05-G (GR) modem
+    - USB: serial: option: add Quectel EM05-G (CS) modem
+    - USB: serial: option: add Quectel EM05-G (RS) modem
+    - USB: serial: option: add Quectel EC200U modem
+    - USB: serial: option: add Quectel EM05CN (SG) modem
+    - USB: serial: option: add Quectel EM05CN modem
+    - staging: vchiq_arm: fix enum vchiq_status return types
+    - USB: misc: iowarrior: fix up header size for USB_DEVICE_ID_CODEMERCS_IOW100
+    - misc: fastrpc: Don't remove map on creater_process and device_release
+    - misc: fastrpc: Fix use-after-free race condition for maps
+    - usb: core: hub: disable autosuspend for TI TUSB8041
+    - comedi: adv_pci1760: Fix PWM instruction handling
+    - ACPI: PRM: Check whether EFI runtime is available
+    - mmc: sunxi-mmc: Fix clock refcount imbalance during unbind
+    - mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting
+    - btrfs: do not abort transaction on failure to write log tree when syncing
+      log
+    - btrfs: fix race between quota rescan and disable leading to NULL pointer
+      deref
+    - cifs: do not include page data when checking signature
+    - thunderbolt: Use correct function to calculate maximum USB3 link rate
+    - riscv: dts: sifive: fu740: fix size of pcie 32bit memory
+    - bpf: restore the ebpf program ID for BPF_AUDIT_UNLOAD and
+      PERF_BPF_EVENT_PROG_UNLOAD
+    - staging: mt7621-dts: change some node hex addresses to lower case
+    - tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
+    - tty: fix possible null-ptr-defer in spk_ttyio_release
+    - USB: serial: cp210x: add SCALANCE LPE-9000 device id
+    - usb: cdns3: remove fetched trb from cache before dequeuing
+    - usb: host: ehci-fsl: Fix module alias
+    - usb: typec: tcpm: Fix altmode re-registration causes sysfs create fail
+    - usb: typec: altmodes/displayport: Add pin assignment helper
+    - usb: typec: altmodes/displayport: Fix pin assignment calculation
+    - usb: gadget: g_webcam: Send color matching descriptor per frame
+    - usb: gadget: f_ncm: fix potential NULL ptr deref in ncm_bitrate()
+    - usb-storage: apply IGNORE_UAS only for HIKSEMI MD202 on RTL9210
+    - dt-bindings: phy: g12a-usb2-phy: fix compatible string documentation
+    - dt-bindings: phy: g12a-usb3-pcie-phy: fix compatible string documentation
+    - serial: pch_uart: Pass correct sg to dma_unmap_sg()
+    - dmaengine: lgm: Move DT parsing after initialization
+    - dmaengine: tegra210-adma: fix global intr clear
+    - dmaengine: idxd: Let probe fail when workqueue cannot be enabled
+    - serial: amba-pl011: fix high priority character transmission in rs486 mode
+    - serial: atmel: fix incorrect baudrate setup
+    - gsmi: fix null-deref in gsmi_get_variable
+    - mei: me: add meteor lake point M DID
+    - drm/i915: re-disable RC6p on Sandy Bridge
+    - drm/i915/display: Check source height is > 0
+    - drm/amd/display: Fix set scaling doesn's work
+    - drm/amd/display: Calculate output_color_space after pixel encoding
+      adjustment
+    - drm/amd/display: Fix COLOR_SPACE_YCBCR2020_TYPE matrix
+    - drm/amdgpu: drop experimental flag on aldebaran
+    - fs/ntfs3: Fix attr_punch_hole() null pointer derenference
+    - arm64: efi: Execute runtime services from a dedicated stack
+    - efi: rt-wrapper: Add missing include
+    - x86/fpu: Use _Alignof to avoid undefined behavior in TYPE_ALIGN
+    - tracing: Use alignof__(struct {type b;}) instead of offsetof()
+    - io_uring: io_kiocb_update_pos() should not touch file for non -1 offset
+    - io_uring/net: fix fast_iov assignment in io_setup_async_msg()
+    - net/mlx5: fix missing mutex_unlock in mlx5_fw_fatal_reporter_err_work()
+    - block: mq-deadline: Rename deadline_is_seq_writes()
+    - soc: qcom: apr: Make qcom,protection-domain optional again
+    - mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
+    - io_uring: Clean up a false-positive warning from GCC 9.3.0
+    - io_uring: fix double poll leak on repolling
+    - io_uring/rw: ensure kiocb_end_write() is always called
+    - io_uring/rw: remove leftover debug statement
+    - Linux 5.15.90
+  * Jammy update: v5.15.89 upstream stable release (LP: #2008929)
+    - ALSA: control-led: use strscpy in set_led_id()
+    - ALSA: hda/realtek - Turn on power early
+    - ALSA: hda/realtek: Enable mute/micmute LEDs on HP Spectre x360 13-aw0xxx
+    - KVM: arm64: Fix S1PTW handling on RO memslots
+    - KVM: arm64: nvhe: Fix build with profile optimization
+    - selftests: kvm: Fix a compile error in selftests/kvm/rseq_test.c
+    - efi: tpm: Avoid READ_ONCE() for accessing the event log
+    - docs: Fix the docs build with Sphinx 6.0
+    - net: stmmac: add aux timestamps fifo clearance wait
+    - perf auxtrace: Fix address filter duplicate symbol selection
+    - s390/kexec: fix ipl report address for kdump
+    - ASoC: qcom: lpass-cpu: Fix fallback SD line index handling
+    - s390/cpum_sf: add READ_ONCE() semantics to compare and swap loops
+    - s390/percpu: add READ_ONCE() to arch_this_cpu_to_op_simple()
+    - drm/virtio: Fix GEM handle creation UAF
+    - drm/i915/gt: Reset twice
+    - net/mlx5e: Set action fwd flag when parsing tc action goto
+    - cifs: Fix uninitialized memory read for smb311 posix symlink create
+    - platform/x86: dell-privacy: Only register SW_CAMERA_LENS_COVER if present
+    - platform/surface: aggregator: Ignore command messages not intended for us
+    - platform/x86: dell-privacy: Fix SW_CAMERA_LENS_COVER reporting
+    - dt-bindings: msm: dsi-controller-main: Fix operating-points-v2 constraint
+    - drm/msm/adreno: Make adreno quirks not overwrite each other
+    - dt-bindings: msm: dsi-controller-main: Fix power-domain constraint
+    - dt-bindings: msm: dsi-controller-main: Fix description of core clock
+    - dt-bindings: msm: dsi-phy-28nm: Add missing qcom, dsi-phy-regulator-ldo-mode
+    - platform/x86: ideapad-laptop: Add Legion 5 15ARH05 DMI id to
+      set_fn_lock_led_list[]
+    - drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux
+      transfer
+    - dt-bindings: msm/dsi: Don't require vdds-supply on 10nm PHY
+    - dt-bindings: msm/dsi: Don't require vcca-supply on 14nm PHY
+    - platform/x86: sony-laptop: Don't turn off 0x153 keyboard backlight during
+      probe
+    - ixgbe: fix pci device refcount leak
+    - ipv6: raw: Deduct extension header length in rawv6_push_pending_frames
+    - bus: mhi: host: Fix race between channel preparation and M0 event
+    - usb: ulpi: defer ulpi_register on ulpi_read_id timeout
+    - iommu/iova: Fix alloc iova overflows issue
+    - iommu/mediatek-v1: Fix an error handling path in mtk_iommu_v1_probe()
+    - sched/core: Fix use-after-free bug in dup_user_cpus_ptr()
+    - netfilter: ipset: Fix overflow before widen in the bitmap_ip_create()
+      function.
+    - powerpc/imc-pmu: Fix use of mutex in IRQs disabled section
+    - x86/boot: Avoid using Intel mnemonics in AT&T syntax asm
+    - EDAC/device: Fix period calculation in edac_device_reset_delay_period()
+    - x86/resctrl: Fix task CLOSID/RMID update race
+    - regulator: da9211: Use irq handler when ready
+    - scsi: mpi3mr: Refer CONFIG_SCSI_MPI3MR in Makefile
+    - scsi: ufs: Stop using the clock scaling lock in the error handler
+    - scsi: ufs: core: WLUN suspend SSU/enter hibern8 fail recovery
+    - ASoC: wm8904: fix wrong outputs volume after power reactivation
+    - ALSA: usb-audio: Make sure to stop endpoints before closing EPs
+    - ALSA: usb-audio: Relax hw constraints for implicit fb sync
+    - tipc: fix unexpected link reset due to discovery messages
+    - octeontx2-af: Fix LMAC config in cgx_lmac_rx_tx_enable
+    - hvc/xen: lock console list traversal
+    - nfc: pn533: Wait for out_urb's completion in pn533_usb_send_frame()
+    - af_unix: selftest: Fix the size of the parameter to connect()
+    - tools/nolibc: x86: Remove `r8`, `r9` and `r10` from the clobber list
+    - tools/nolibc: x86-64: Use `mov $60,%eax` instead of `mov $60,%rax`
+    - tools/nolibc: use pselect6 on RISCV
+    - tools/nolibc/std: move the standard type definitions to std.h
+    - tools/nolibc/types: split syscall-specific definitions into their own files
+    - tools/nolibc/arch: split arch-specific code into individual files
+    - tools/nolibc/arch: mark the _start symbol as weak
+    - tools/nolibc: Remove .global _start from the entry point code
+    - tools/nolibc: restore mips branch ordering in the _start block
+    - tools/nolibc: fix the O_* fcntl/open macro definitions for riscv
+    - net/sched: act_mpls: Fix warning during failed attribute validation
+    - net/mlx5: Fix ptp max frequency adjustment range
+    - net/mlx5e: Don't support encap rules with gbp option
+    - perf build: Properly guard libbpf includes
+    - igc: Fix PPS delta between two synchronized end-points
+    - platform/surface: aggregator: Add missing call to ssam_request_sync_free()
+    - Documentation: KVM: add API issues section
+    - KVM: x86: Do not return host topology information from
+      KVM_GET_SUPPORTED_CPUID
+    - io_uring: lock overflowing for IOPOLL
+    - arm64: atomics: format whitespace consistently
+    - arm64: atomics: remove LL/SC trampolines
+    - arm64: cmpxchg_double*: hazard against entire exchange variable
+    - efi: fix NULL-deref in init error path
+    - io_uring/io-wq: free worker if task_work creation is canceled
+    - io_uring/io-wq: only free worker if it was allocated for creation
+    - block: handle bio_split_to_limits() NULL return
+    - Revert "usb: ulpi: defer ulpi_register on ulpi_read_id timeout"
+    - pinctrl: amd: Add dynamic debugging for active GPIOs
+    - Linux 5.15.89
+  * Jammy update: v5.15.88 upstream stable release (LP: #2008927)
+    - parisc: Align parisc MADV_XXX constants with all other architectures
+    - serial: fixup backport of "serial: Deassert Transmit Enable on probe in
+      driver-specific way"
+    - net: sched: disallow noqueue for qdisc classes
+    - ALSA: hda/hdmi: Add a HP device 0x8715 to force connect list
+    - ALSA: hda - Enable headset mic on another Dell laptop with ALC3254
+    - Linux 5.15.88
+  * Fix selftests/ftracetests/Meta-selftests (LP: #2006453)
+    - selftests/ftrace: Fix bash specific "==" operator
+
+  [ Ubuntu: 5.15.0-69.76 ]
+
+  * jammy/linux: 5.15.0-69.76 -proposed tracker (LP: #2012092)
+  * NFS deathlock with last Kernel 5.4.0-144.161 and 5.15.0-67.74 (LP: #2009325)
+    - NFS: Correct timing for assigning access cache timestamp
+
+  [ Ubuntu: 5.15.0-68.75 ]
+
+  * jammy/linux: 5.15.0-68.75 -proposed tracker (LP: #2008349)
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2023.02.27)
+  * Ubuntu 22.04 kernel 5.15.0-46-generic leaks kernel memory in kmalloc-2k
+    slabs (LP: #1987430)
+    - SAUCE: audit: fix memory leak of audit_log_lsm()
+  * [EGS] Backport intel_idle support for Eagle Stream Ubuntu 22.04 release
+    (LP: #2003267)
+    - intel_idle: add SPR support
+    - intel_idle: add 'preferred_cstates' module argument
+    - intel_idle: add core C6 optimization for SPR
+    - cpuidle: intel_idle: Drop redundant backslash at line end
+    - intel_idle: Fix the 'preferred_cstates' module parameter
+    - intel_idle: Fix SPR C6 optimization
+    - intel_idle: make SPR C1 and C1E be independent
+  * Fix speaker mute hotkey doesn't work on Dell G16 series (LP: #2003161)
+    - platform/x86: dell-wmi: Add a keymap for KEY_MUTE in type 0x0010 table
+  * Fix the ACPI _CPC not found error from kernel dmesg on some dynamic SSDT
+    table loaded firmwares (LP: #2006077)
+    - ACPI: bus: Avoid using CPPC if not supported by firmware
+    - ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
+    - ACPI: CPPC: Only probe for _CPC if CPPC v2 is acked
+  * rtcpie in timers from ubuntu_kernel_selftests randomly failing
+    (LP: #1814234)
+    - SAUCE: selftest: rtcpie: Force passing unreliable subtest
+  * Jammy update: v5.15.87 upstream stable release (LP: #2007441)
+    - usb: dwc3: qcom: Fix memory leak in dwc3_qcom_interconnect_init
+    - cifs: fix oops during encryption
+    - nvme-pci: fix doorbell buffer value endianness
+    - nvme-pci: fix mempool alloc size
+    - nvme-pci: fix page size checks
+    - ACPI: resource: do IRQ override on LENOVO IdeaPad
+    - ACPI: resource: do IRQ override on XMG Core 15
+    - ACPI: resource: do IRQ override on Lenovo 14ALC7
+    - block, bfq: fix uaf for bfqq in bfq_exit_icq_bfqq
+    - ata: ahci: Fix PCS quirk application for suspend
+    - nvme: fix the NVME_CMD_EFFECTS_CSE_MASK definition
+    - nvmet: don't defer passthrough commands with trivial effects to the
+      workqueue
+    - fs/ntfs3: Validate BOOT record_size
+    - fs/ntfs3: Add overflow check for attribute size
+    - fs/ntfs3: Validate data run offset
+    - fs/ntfs3: Add null pointer check to attr_load_runs_vcn
+    - fs/ntfs3: Fix memory leak on ntfs_fill_super() error path
+    - fs/ntfs3: Add null pointer check for inode operations
+    - fs/ntfs3: Validate attribute name offset
+    - fs/ntfs3: Validate buffer length while parsing index
+    - fs/ntfs3: Validate resident attribute name
+    - fs/ntfs3: Fix slab-out-of-bounds read in run_unpack
+    - soundwire: dmi-quirks: add quirk variant for LAPBC710 NUC15
+    - fs/ntfs3: Validate index root when initialize NTFS security
+    - fs/ntfs3: Use __GFP_NOWARN allocation at wnd_init()
+    - fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_fill_super()
+    - fs/ntfs3: Delete duplicate condition in ntfs_read_mft()
+    - fs/ntfs3: Fix slab-out-of-bounds in r_page
+    - objtool: Fix SEGFAULT
+    - powerpc/rtas: avoid device tree lookups in rtas_os_term()
+    - powerpc/rtas: avoid scheduling in rtas_os_term()
+    - HID: multitouch: fix Asus ExpertBook P2 P2451FA trackpoint
+    - HID: plantronics: Additional PIDs for double volume key presses quirk
+    - pstore: Properly assign mem_type property
+    - pstore/zone: Use GFP_ATOMIC to allocate zone buffer
+    - hfsplus: fix bug causing custom uid and gid being unable to be assigned with
+      mount
+    - binfmt: Fix error return code in load_elf_fdpic_binary()
+    - ovl: Use ovl mounter's fsuid and fsgid in ovl_link()
+    - ALSA: line6: correct midi status byte when receiving data from podxt
+    - ALSA: line6: fix stack overflow in line6_midi_transmit
+    - pnode: terminate at peers of source
+    - mfd: mt6360: Add bounds checking in Regmap read/write call-backs
+    - md: fix a crash in mempool_free
+    - mm, compaction: fix fast_isolate_around() to stay within boundaries
+    - f2fs: should put a page when checking the summary info
+    - f2fs: allow to read node block after shutdown
+    - mmc: vub300: fix warning - do not call blocking ops when !TASK_RUNNING
+    - tpm: acpi: Call acpi_put_table() to fix memory leak
+    - tpm: tpm_crb: Add the missed acpi_put_table() to fix memory leak
+    - tpm: tpm_tis: Add the missed acpi_put_table() to fix memory leak
+    - SUNRPC: Don't leak netobj memory when gss_read_proxy_verf() fails
+    - kcsan: Instrument memcpy/memset/memmove with newer Clang
+    - ASoC: Intel/SOF: use set_stream() instead of set_tdm_slots() for HDAudio
+    - ASoC/SoundWire: dai: expand 'stream' concept beyond SoundWire
+    - rcu-tasks: Simplify trc_read_check_handler() atomic operations
+    - net/af_packet: add VLAN support for AF_PACKET SOCK_RAW GSO
+    - net/af_packet: make sure to pull mac header
+    - media: stv0288: use explicitly signed char
+    - soc: qcom: Select REMAP_MMIO for LLCC driver
+    - kest.pl: Fix grub2 menu handling for rebooting
+    - ktest.pl minconfig: Unset configs instead of just removing them
+    - jbd2: use the correct print format
+    - perf/x86/intel/uncore: Disable I/O stacks to PMU mapping on ICX-D
+    - perf/x86/intel/uncore: Clear attr_update properly
+    - arm64: dts: qcom: sdm845-db845c: correct SPI2 pins drive strength
+    - mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K
+    - btrfs: fix resolving backrefs for inline extent followed by prealloc
+    - ARM: ux500: do not directly dereference __iomem
+    - arm64: dts: qcom: sdm850-lenovo-yoga-c630: correct I2C12 pins drive strength
+    - selftests: Use optional USERCFLAGS and USERLDFLAGS
+    - PM/devfreq: governor: Add a private governor_data for governor
+    - cpufreq: Init completion before kobject_init_and_add()
+    - ALSA: patch_realtek: Fix Dell Inspiron Plus 16
+    - ALSA: hda/realtek: Apply dual codec fixup for Dell Latitude laptops
+    - fs: dlm: fix sock release if listen fails
+    - fs: dlm: retry accept() until -EAGAIN or error returns
+    - mptcp: mark ops structures as ro_after_init
+    - mptcp: remove MPTCP 'ifdef' in TCP SYN cookies
+    - dm cache: Fix ABBA deadlock between shrink_slab and dm_cache_metadata_abort
+    - dm thin: Fix ABBA deadlock between shrink_slab and dm_pool_abort_metadata
+    - dm thin: Use last transaction's pmd->root when commit failed
+    - dm thin: resume even if in FAIL mode
+    - dm thin: Fix UAF in run_timer_softirq()
+    - dm integrity: Fix UAF in dm_integrity_dtr()
+    - dm clone: Fix UAF in clone_dtr()
+    - dm cache: Fix UAF in destroy()
+    - dm cache: set needs_check flag after aborting metadata
+    - tracing/hist: Fix out-of-bound write on 'action_data.var_ref_idx'
+    - perf/core: Call LSM hook after copying perf_event_attr
+    - of/kexec: Fix reading 32-bit "linux,initrd-{start,end}" values
+    - KVM: VMX: Resume guest immediately when injecting #GP on ECREATE
+    - KVM: nVMX: Inject #GP, not #UD, if "generic" VMXON CR0/CR4 check fails
+    - KVM: nVMX: Properly expose ENABLE_USR_WAIT_PAUSE control to L1
+    - x86/microcode/intel: Do not retry microcode reloading on the APs
+    - ftrace/x86: Add back ftrace_expected for ftrace bug reports
+    - x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
+    - x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
+    - tracing: Fix race where eprobes can be called before the event
+    - tracing: Fix complicated dependency of CONFIG_TRACER_MAX_TRACE
+    - tracing/hist: Fix wrong return value in parse_action_params()
+    - tracing/probes: Handle system names with hyphens
+    - tracing: Fix infinite loop in tracing_read_pipe on overflowed
+      print_trace_line
+    - staging: media: tegra-video: fix chan->mipi value on error
+    - staging: media: tegra-video: fix device_node use after free
+    - ARM: 9256/1: NWFPE: avoid compiler-generated __aeabi_uldivmod
+    - media: dvb-core: Fix double free in dvb_register_device()
+    - cifs: fix confusing debug message
+    - cifs: fix missing display of three mount options
+    - rtc: ds1347: fix value written to century register
+    - block: mq-deadline: Do not break sequential write streams to zoned HDDs
+    - md/bitmap: Fix bitmap chunk size overflow issues
+    - efi: Add iMac Pro 2017 to uefi skip cert quirk
+    - wifi: wilc1000: sdio: fix module autoloading
+    - ASoC: jz4740-i2s: Handle independent FIFO flush bits
+    - ipu3-imgu: Fix NULL pointer dereference in imgu_subdev_set_selection()
+    - ipmi: fix long wait in unload when IPMI disconnect
+    - mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
+    - ima: Fix a potential NULL pointer access in ima_restore_measurement_list
+    - ipmi: fix use after free in _ipmi_destroy_user()
+    - PCI: Fix pci_device_is_present() for VFs by checking PF
+    - PCI/sysfs: Fix double free in error path
+    - riscv: stacktrace: Fixup ftrace_graph_ret_addr retp argument
+    - riscv: mm: notify remote harts about mmu cache updates
+    - crypto: n2 - add missing hash statesize
+    - driver core: Fix bus_type.match() error handling in __driver_attach()
+    - phy: qcom-qmp-combo: fix sc8180x reset
+    - iommu/amd: Fix ivrs_acpihid cmdline parsing code
+    - remoteproc: core: Do pm_relax when in RPROC_OFFLINE state
+    - parisc: led: Fix potential null-ptr-deref in start_task()
+    - device_cgroup: Roll back to original exceptions after copy failure
+    - drm/connector: send hotplug uevent on connector cleanup
+    - drm/vmwgfx: Validate the box size for the snooped cursor
+    - drm/i915/dsi: fix VBT send packet port selection for dual link DSI
+    - drm/ingenic: Fix missing platform_driver_unregister() call in
+      ingenic_drm_init()
+    - ext4: silence the warning when evicting inode with dioread_nolock
+    - ext4: add inode table check in __ext4_get_inode_loc to aovid possible
+      infinite loop
+    - ext4: remove trailing newline from ext4_msg() message
+    - fs: ext4: initialize fsdata in pagecache_write()
+    - ext4: fix use-after-free in ext4_orphan_cleanup
+    - ext4: fix undefined behavior in bit shift for ext4_check_flag_values
+    - ext4: add EXT4_IGET_BAD flag to prevent unexpected bad inode
+    - ext4: add helper to check quota inums
+    - ext4: fix bug_on in __es_tree_search caused by bad quota inode
+    - ext4: fix reserved cluster accounting in __es_remove_extent()
+    - ext4: check and assert if marking an no_delete evicting inode dirty
+    - ext4: fix bug_on in __es_tree_search caused by bad boot loader inode
+    - ext4: fix leaking uninitialized memory in fast-commit journal
+    - ext4: fix uninititialized value in 'ext4_evict_inode'
+    - ext4: init quota for 'old.inode' in 'ext4_rename'
+    - ext4: fix delayed allocation bug in ext4_clu_mapped for bigalloc + inline
+    - ext4: fix error code return to user-space in ext4_get_branch()
+    - ext4: avoid BUG_ON when creating xattrs
+    - ext4: fix kernel BUG in 'ext4_write_inline_data_end()'
+    - ext4: fix inode leak in ext4_xattr_inode_create() on an error path
+    - ext4: initialize quota before expanding inode in setproject ioctl
+    - ext4: avoid unaccounted block allocation when expanding inode
+    - ext4: allocate extended attribute value in vmalloc area
+    - drm/amdgpu: handle polaris10/11 overlap asics (v2)
+    - block: mq-deadline: Fix dd_finish_request() for zoned devices
+    - tracing: Fix issue of missing one synthetic field
+    - ext4: remove unused enum EXT4_FC_COMMIT_FAILED
+    - ext4: use ext4_debug() instead of jbd_debug()
+    - ext4: introduce EXT4_FC_TAG_BASE_LEN helper
+    - ext4: factor out ext4_fc_get_tl()
+    - ext4: fix potential out of bound read in ext4_fc_replay_scan()
+    - ext4: disable fast-commit of encrypted dir operations
+    - ext4: don't set up encryption key during jbd2 transaction
+    - ext4: add missing validation of fast-commit record lengths
+    - ext4: fix unaligned memory access in ext4_fc_reserve_space()
+    - ext4: fix off-by-one errors in fast-commit block filling
+    - ARM: renumber bits related to _TIF_WORK_MASK
+    - phy: qcom-qmp-combo: fix out-of-bounds clock access
+    - btrfs: replace strncpy() with strscpy()
+    - btrfs: move missing device handling in a dedicate function
+    - btrfs: fix extent map use-after-free when handling missing device in
+      read_one_chunk
+    - x86/mce: Get rid of msr_ops
+    - x86/MCE/AMD: Clear DFR errors found in THR handler
+    - media: s5p-mfc: Fix to handle reference queue during finishing
+    - media: s5p-mfc: Clear workbit to handle error condition
+    - media: s5p-mfc: Fix in register read and write for H264
+    - perf probe: Use dwarf_attr_integrate as generic DWARF attr accessor
+    - perf probe: Fix to get the DW_AT_decl_file and DW_AT_call_file as unsinged
+      data
+    - ravb: Fix "failed to switch device to config mode" message during unbind
+    - ext4: goto right label 'failed_mount3a'
+    - ext4: correct inconsistent error msg in nojournal mode
+    - mbcache: automatically delete entries from cache on freeing
+    - ext4: fix deadlock due to mbcache entry corruption
+    - drm/i915/migrate: don't check the scratch page
+    - drm/i915/migrate: fix offset calculation
+    - drm/i915/migrate: fix length calculation
+    - SUNRPC: ensure the matching upcall is in-flight upon downcall
+    - btrfs: fix an error handling path in btrfs_defrag_leaves()
+    - bpf: pull before calling skb_postpull_rcsum()
+    - drm/panfrost: Fix GEM handle creation ref-counting
+    - netfilter: nf_tables: consolidate set description
+    - netfilter: nf_tables: add function to create set stateful expressions
+    - netfilter: nf_tables: perform type checking for existing sets
+    - vmxnet3: correctly report csum_level for encapsulated packet
+    - netfilter: nf_tables: honor set timeout and garbage collection updates
+    - veth: Fix race with AF_XDP exposing old or uninitialized descriptors
+    - nfsd: shut down the NFSv4 state objects before the filecache
+    - net: hns3: add interrupts re-initialization while doing VF FLR
+    - net: hns3: refactor hns3_nic_reuse_page()
+    - net: hns3: extract macro to simplify ring stats update code
+    - net: hns3: fix miss L3E checking for rx packet
+    - net: hns3: fix VF promisc mode not update when mac table full
+    - net: sched: fix memory leak in tcindex_set_parms
+    - qlcnic: prevent ->dcb use-after-free on qlcnic_dcb_enable() failure
+    - net: dsa: mv88e6xxx: depend on PTP conditionally
+    - nfc: Fix potential resource leaks
+    - vdpa_sim: fix possible memory leak in vdpasim_net_init() and
+      vdpasim_blk_init()
+    - vhost/vsock: Fix error handling in vhost_vsock_init()
+    - vringh: fix range used in iotlb_translate()
+    - vhost: fix range used in translate_desc()
+    - vdpa_sim: fix vringh initialization in vdpasim_queue_ready()
+    - net/mlx5: E-Switch, properly handle ingress tagged packets on VST
+    - net/mlx5: Add forgotten cleanup calls into mlx5_init_once() error path
+    - net/mlx5: Avoid recovery in probe flows
+    - net/mlx5e: IPoIB, Don't allow CQE compression to be turned on by default
+    - net/mlx5e: TC, Refactor mlx5e_tc_add_flow_mod_hdr() to get flow attr
+    - net/mlx5e: Always clear dest encap in neigh-update-del
+    - net/mlx5e: Fix hw mtu initializing at XDP SQ allocation
+    - net: amd-xgbe: add missed tasklet_kill
+    - net: ena: Fix toeplitz initial hash value
+    - net: ena: Don't register memory info on XDP exchange
+    - net: ena: Account for the number of processed bytes in XDP
+    - net: ena: Use bitmask to indicate packet redirection
+    - net: ena: Fix rx_copybreak value update
+    - net: ena: Set default value for RX interrupt moderation
+    - net: ena: Update NUMA TPH hint register upon NUMA node update
+    - net: phy: xgmiitorgmii: Fix refcount leak in xgmiitorgmii_probe
+    - RDMA/mlx5: Fix mlx5_ib_get_hw_stats when used for device
+    - RDMA/mlx5: Fix validation of max_rd_atomic caps for DC
+    - drm/meson: Reduce the FIFO lines held when AFBC is not used
+    - filelock: new helper: vfs_inode_has_locks
+    - ceph: switch to vfs_inode_has_locks() to fix file lock bug
+    - gpio: sifive: Fix refcount leak in sifive_gpio_probe
+    - net: sched: atm: dont intepret cls results when asked to drop
+    - net: sched: cbq: dont intepret cls results when asked to drop
+    - net: sparx5: Fix reading of the MAC address
+    - netfilter: ipset: fix hash:net,port,net hang with /0 subnet
+    - netfilter: ipset: Rework long task execution when adding/deleting entries
+    - perf tools: Fix resources leak in perf_data__open_dir()
+    - drm/imx: ipuv3-plane: Fix overlay plane width
+    - fs/ntfs3: don't hold ni_lock when calling truncate_setsize()
+    - drivers/net/bonding/bond_3ad: return when there's no aggregator
+    - octeontx2-pf: Fix lmtst ID used in aura free
+    - usb: rndis_host: Secure rndis_query check against int overflow
+    - perf stat: Fix handling of --for-each-cgroup with --bpf-counters to match
+      non BPF mode
+    - drm/i915: unpin on error in intel_vgpu_shadow_mm_pin()
+    - caif: fix memory leak in cfctrl_linkup_request()
+    - udf: Fix extension of the last extent in the file
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
+    - nvme: fix multipath crash caused by flush request when blktrace is enabled
+    - io_uring: check for valid register opcode earlier
+    - nvmet: use NVME_CMD_EFFECTS_CSUPP instead of open coding it
+    - nvme: also return I/O command effects from nvme_command_effects
+    - btrfs: check superblock to ensure the fs was not modified at thaw time
+    - x86/kexec: Fix double-free of elf header buffer
+    - nfsd: fix handling of readdir in v4root vs. mount upcall timeout
+    - fbdev: matroxfb: G200eW: Increase max memory from 1 MB to 16 MB
+    - block: don't allow splitting of a REQ_NOWAIT bio
+    - io_uring: fix CQ waiting timeout handling
+    - thermal: int340x: Add missing attribute for data rate base
+    - riscv: uaccess: fix type of 0 variable on error in get_user()
+    - riscv, kprobes: Stricter c.jr/c.jalr decoding
+    - drm/i915/gvt: fix gvt debugfs destroy
+    - drm/i915/gvt: fix vgpu debugfs clean in remove
+    - hfs/hfsplus: use WARN_ON for sanity check
+    - hfs/hfsplus: avoid WARN_ON() for sanity check, use proper error handling
+    - ksmbd: fix infinite loop in ksmbd_conn_handler_loop()
+    - ksmbd: check nt_len to be at least CIFS_ENCPWD_SIZE in
+      ksmbd_decode_ntlmssp_auth_blob
+    - Revert "ACPI: PM: Add support for upcoming AMD uPEP HID AMDI007"
+    - mptcp: dedicated request sock for subflow in v6
+    - mptcp: use proper req destructor for IPv6
+    - ext4: don't allow journal inode to have encrypt flag
+    - selftests: set the BUILD variable to absolute path
+    - btrfs: make thaw time super block check to also verify checksum
+    - net: hns3: fix return value check bug of rx copybreak
+    - mbcache: Avoid nesting of cache->c_list_lock under bit locks
+    - efi: random: combine bootloader provided RNG seed with RNG protocol output
+    - io_uring: Fix unsigned 'res' comparison with zero in io_fixup_rw_res()
+    - drm/mgag200: Fix PLL setup for G200_SE_A rev >=4
+    - Linux 5.15.87
+  * Jammy update: v5.15.87 upstream stable release (LP: #2007441) //
+    CVE-2022-41218 is assigned to those bugs above.
+    - media: dvb-core: Fix UAF due to refcount races at releasing
+  * RaptorLake: Fix the Screen is shaking by onboard HDMI port in mirror mode
+    (LP: #1993561)
+    - drm/i915/display: Drop check for doublescan mode in modevalid
+    - drm/i915/display: Prune Interlace modes for Display >=12
+  * CVE-2023-0266 // CVE-2023-0266 was assigned for this issue.
+    - ALSA: pcm: Move rwsem lock inside snd_ctl_elem_read to prevent UAF
+  * CVE-2022-4382
+    - USB: gadgetfs: Fix race between mounting and unmounting
+  * CVE-2022-2196
+    - KVM: VMX: Execute IBPB on emulated VM-exit when guest has IBRS
+  * ubuntu_kernel_selftests: net:udpgso_bench.sh failed (LP: #1951447)
+    - selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
+  * net:fcnal-test.sh didn't return a non-zero value even with some sub-tests
+    failed (LP: #2006692)
+    - selftests: net/fcnal-test.sh: add exit code
+  * LXD containers using shiftfs on ZFS or TMPFS broken on 5.15.0-48.54
+    (LP: #1990849)
+    - SAUCE: shiftfs: always rely on init_user_ns
+    - [SAUCE] shiftfs: fix -EOVERFLOW inside the container
+  * Regression in ext4 during online resize (LP: #2003816)
+    - ext4: fix bad checksum after online resize
+    - ext4: fix corruption when online resizing a 1K bigalloc fs
+    - SAUCE: Export ext4_superblock_csum function
+    - ext4: fix corrupt backup group descriptors after online resize
+  * Jammy update: v5.15.86 upstream stable release (LP: #2005113)
+    - usb: musb: remove extra check in musb_gadget_vbus_draw
+    - arm64: dts: qcom: ipq6018-cp01-c1: use BLSPI1 pins
+    - arm64: dts: qcom: sm8250-sony-xperia-edo: fix touchscreen bias-disable
+    - arm64: dts: qcom: msm8996: Add MSM8996 Pro support
+    - arm64: dts: qcom: msm8996: fix supported-hw in cpufreq OPP tables
+    - arm64: dts: qcom: msm8996: fix GPU OPP table
+    - ARM: dts: qcom: apq8064: fix coresight compatible
+    - arm64: dts: qcom: sdm630: fix UART1 pin bias
+    - arm64: dts: qcom: sdm845-cheza: fix AP suspend pin bias
+    - arm64: dts: qcom: msm8916: Drop MSS fallback compatible
+    - objtool, kcsan: Add volatile read/write instrumentation to whitelist
+    - ARM: dts: stm32: Drop stm32mp15xc.dtsi from Avenger96
+    - ARM: dts: stm32: Fix AV96 WLAN regulator gpio property
+    - drivers: soc: ti: knav_qmss_queue: Mark knav_acc_firmwares as static
+    - arm64: dts: qcom: pm660: Use unique ADC5_VCOIN address in node name
+    - arm64: dts: qcom: sm8250: correct LPASS pin pull down
+    - soc: qcom: llcc: make irq truly optional
+    - arm64: dts: qcom: Correct QMP PHY child node name
+    - arm64: dts: qcom: sm8150: fix UFS PHY registers
+    - arm64: dts: qcom: sm8250: fix UFS PHY registers
+    - arm64: dts: qcom: sm8350: fix UFS PHY registers
+    - arm64: dts: qcom: sm8250: drop bogus DP PHY clock
+    - soc: qcom: apr: make code more reuseable
+    - soc: qcom: apr: Add check for idr_alloc and of_property_read_string_index
+    - arm64: dts: qcom: sm6125: fix SDHCI CQE reg names
+    - arm: dts: spear600: Fix clcd interrupt
+    - soc: ti: knav_qmss_queue: Use pm_runtime_resume_and_get instead of
+      pm_runtime_get_sync
+    - soc: ti: knav_qmss_queue: Fix PM disable depth imbalance in knav_queue_probe
+    - soc: ti: smartreflex: Fix PM disable depth imbalance in omap_sr_probe
+    - arm64: Treat ESR_ELx as a 64-bit register
+    - arm64: mm: kfence: only handle translation faults
+    - perf: arm_dsu: Fix hotplug callback leak in dsu_pmu_init()
+    - perf/arm_dmc620: Fix hotplug callback leak in dmc620_pmu_init()
+    - perf/smmuv3: Fix hotplug callback leak in arm_smmu_pmu_init()
+    - arm64: dts: ti: k3-am65-main: Drop dma-coherent in crypto node
+    - arm64: dts: ti: k3-j721e-main: Drop dma-coherent in crypto node
+    - ARM: dts: nuvoton: Remove bogus unit addresses from fixed-partition nodes
+    - arm64: dts: mt6779: Fix devicetree build warnings
+    - arm64: dts: mt2712e: Fix unit_address_vs_reg warning for oscillators
+    - arm64: dts: mt2712e: Fix unit address for pinctrl node
+    - arm64: dts: mt2712-evb: Fix vproc fixed regulators unit names
+    - arm64: dts: mt2712-evb: Fix usb vbus regulators unit names
+    - arm64: dts: mediatek: pumpkin-common: Fix devicetree warnings
+    - arm64: dts: mediatek: mt6797: Fix 26M oscillator unit name
+    - ARM: dts: dove: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-370: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-xp: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-375: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-38x: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: armada-39x: Fix assigned-addresses for every PCIe Root Port
+    - ARM: dts: turris-omnia: Add ethernet aliases
+    - ARM: dts: turris-omnia: Add switch port 6 node
+    - arm64: dts: armada-3720-turris-mox: Add missing interrupt for RTC
+    - seccomp: Move copy_seccomp() to no failure path.
+    - pstore/ram: Fix error return code in ramoops_probe()
+    - ARM: mmp: fix timer_read delay
+    - pstore: Avoid kcore oops by vmap()ing with VM_IOREMAP
+    - tpm/tpm_ftpm_tee: Fix error handling in ftpm_mod_init()
+    - tpm/tpm_crb: Fix error message in __crb_relinquish_locality()
+    - ovl: store lower path in ovl_inode
+    - ovl: use ovl_copy_{real,upper}attr() wrappers
+    - ovl: remove privs in ovl_copyfile()
+    - ovl: remove privs in ovl_fallocate()
+    - sched/fair: Cleanup task_util and capacity type
+    - sched/uclamp: Fix relationship between uclamp and migration margin
+    - sched/uclamp: Make task_fits_capacity() use util_fits_cpu()
+    - sched/uclamp: Make select_idle_capacity() use util_fits_cpu()
+    - sched/fair: Removed useless update of p->recent_used_cpu
+    - sched/core: Introduce sched_asym_cpucap_active()
+    - sched/uclamp: Make asym_fits_capacity() use util_fits_cpu()
+    - cpuidle: dt: Return the correct numbers of parsed idle states
+    - alpha: fix TIF_NOTIFY_SIGNAL handling
+    - alpha: fix syscall entry in !AUDUT_SYSCALL case
+    - x86/sgx: Reduce delay and interference of enclave release
+    - PM: hibernate: Fix mistake in kerneldoc comment
+    - fs: don't audit the capability check in simple_xattr_list()
+    - cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut()
+    - selftests/ftrace: event_triggers: wait longer for test_event_enable
+    - perf: Fix possible memleak in pmu_dev_alloc()
+    - lib/debugobjects: fix stat count and optimize debug_objects_mem_init
+    - platform/x86: huawei-wmi: fix return value calculation
+    - timerqueue: Use rb_entry_safe() in timerqueue_getnext()
+    - proc: fixup uptime selftest
+    - lib/fonts: fix undefined behavior in bit shift for get_default_font
+    - ocfs2: fix memory leak in ocfs2_stack_glue_init()
+    - MIPS: vpe-mt: fix possible memory leak while module exiting
+    - MIPS: vpe-cmp: fix possible memory leak while module exiting
+    - selftests/efivarfs: Add checking of the test return value
+    - PNP: fix name memory leak in pnp_alloc_dev()
+    - perf/x86/intel/uncore: Fix reference count leak in sad_cfg_iio_topology()
+    - perf/x86/intel/uncore: Fix reference count leak in hswep_has_limit_sbox()
+    - perf/x86/intel/uncore: Fix reference count leak in snr_uncore_mmio_map()
+    - perf/x86/intel/uncore: Fix reference count leak in __uncore_imc_init_box()
+    - platform/chrome: cros_usbpd_notify: Fix error handling in
+      cros_usbpd_notify_init()
+    - thermal: core: fix some possible name leaks in error paths
+    - irqchip: gic-pm: Use pm_runtime_resume_and_get() in gic_probe()
+    - irqchip/wpcm450: Fix memory leak in wpcm450_aic_of_init()
+    - EDAC/i10nm: fix refcount leak in pci_get_dev_wrapper()
+    - SUNRPC: Return true/false (not 1/0) from bool functions
+    - NFSD: Finish converting the NFSv2 GETACL result encoder
+    - nfsd: don't call nfsd_file_put from client states seqfile display
+    - genirq/irqdesc: Don't try to remove non-existing sysfs files
+    - cpufreq: amd_freq_sensitivity: Add missing pci_dev_put()
+    - libfs: add DEFINE_SIMPLE_ATTRIBUTE_SIGNED for signed value
+    - lib/notifier-error-inject: fix error when writing -errno to debugfs file
+    - debugfs: fix error when writing negative value to atomic_t debugfs file
+    - rapidio: fix possible name leaks when rio_add_device() fails
+    - rapidio: rio: fix possible name leak in rio_register_mport()
+    - clocksource/drivers/sh_cmt: Access registers according to spec
+    - mips: ralink: mt7621: define MT7621_SYSC_BASE with __iomem
+    - mips: ralink: mt7621: soc queries and tests as functions
+    - mips: ralink: mt7621: do not use kzalloc too early
+    - futex: Move to kernel/futex/
+    - futex: Resend potentially swallowed owner death notification
+    - cpu/hotplug: Make target_store() a nop when target == state
+    - cpu/hotplug: Do not bail-out in DYING/STARTING sections
+    - clocksource/drivers/timer-ti-dm: Fix missing clk_disable_unprepare in
+      dmtimer_systimer_init_clock()
+    - ACPICA: Fix use-after-free in acpi_ut_copy_ipackage_to_ipackage()
+    - uprobes/x86: Allow to probe a NOP instruction with 0x66 prefix
+    - x86/xen: Fix memory leak in xen_smp_intr_init{_pv}()
+    - x86/xen: Fix memory leak in xen_init_lock_cpu()
+    - xen/privcmd: Fix a possible warning in privcmd_ioctl_mmap_resource()
+    - PM: runtime: Do not call __rpm_callback() from rpm_idle()
+    - platform/chrome: cros_ec_typec: Cleanup switch handle return paths
+    - platform/chrome: cros_ec_typec: zero out stale pointers
+    - platform/x86: mxm-wmi: fix memleak in mxm_wmi_call_mx[ds|mx]()
+    - platform/x86: intel_scu_ipc: fix possible name leak in
+      __intel_scu_ipc_register()
+    - MIPS: BCM63xx: Add check for NULL for clk in clk_enable
+    - MIPS: OCTEON: warn only once if deprecated link status is being used
+    - lockd: set other missing fields when unlocking files
+    - fs: sysv: Fix sysv_nblocks() returns wrong value
+    - rapidio: fix possible UAF when kfifo_alloc() fails
+    - eventfd: change int to __u64 in eventfd_signal() ifndef CONFIG_EVENTFD
+    - relay: fix type mismatch when allocating memory in relay_create_buf()
+    - hfs: Fix OOB Write in hfs_asc2mac
+    - rapidio: devices: fix missing put_device in mport_cdev_open
+    - platform/mellanox: mlxbf-pmc: Fix event typo
+    - wifi: ath9k: hif_usb: fix memory leak of urbs in
+      ath9k_hif_usb_dealloc_tx_urbs()
+    - wifi: ath9k: hif_usb: Fix use-after-free in ath9k_hif_usb_reg_in_cb()
+    - wifi: rtl8xxxu: Fix reading the vendor of combo chips
+    - drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge
+    - libbpf: Fix use-after-free in btf_dump_name_dups
+    - libbpf: Fix null-pointer dereference in find_prog_by_sec_insn()
+    - ata: libata: move ata_{port,link,dev}_dbg to standard pr_XXX() macros
+    - ata: add/use ata_taskfile::{error|status} fields
+    - ata: libata: fix NCQ autosense logic
+    - ipmi: kcs: Poll OBF briefly to reduce OBE latency
+    - drm/amdgpu/powerplay/psm: Fix memory leak in power state init
+    - media: v4l2-ctrls: Fix off-by-one error in integer menu control check
+    - media: coda: jpeg: Add check for kmalloc
+    - media: adv748x: afe: Select input port when initializing AFE
+    - media: i2c: ad5820: Fix error path
+    - venus: pm_helpers: Fix error check in vcodec_domains_get()
+    - soreuseport: Fix socket selection for SO_INCOMING_CPU.
+    - media: exynos4-is: don't rely on the v4l2_async_subdev internals
+    - libbpf: Btf dedup identical struct test needs check for nested
+      structs/arrays
+    - can: kvaser_usb: do not increase tx statistics when sending error message
+      frames
+    - can: kvaser_usb: kvaser_usb_leaf: Get capabilities from device
+    - can: kvaser_usb: kvaser_usb_leaf: Rename {leaf,usbcan}_cmd_error_event to
+      {leaf,usbcan}_cmd_can_error_event
+    - can: kvaser_usb: kvaser_usb_leaf: Handle CMD_ERROR_EVENT
+    - can: kvaser_usb_leaf: Set Warning state even without bus errors
+    - can: kvaser_usb: make use of units.h in assignment of frequency
+    - can: kvaser_usb_leaf: Fix improved state not being reported
+    - can: kvaser_usb_leaf: Fix wrong CAN state after stopping
+    - can: kvaser_usb_leaf: Fix bogus restart events
+    - can: kvaser_usb: Add struct kvaser_usb_busparams
+    - can: kvaser_usb: Compare requested bittiming parameters with actual
+      parameters in do_set_{,data}_bittiming
+    - drm/rockchip: lvds: fix PM usage counter unbalance in poweron
+    - clk: renesas: r9a06g032: Repair grave increment error
+    - spi: Update reference to struct spi_controller
+    - drm/panel/panel-sitronix-st7701: Remove panel on DSI attach failure
+    - drm/msm/hdmi: drop unused GPIO support
+    - drm/msm/hdmi: use devres helper for runtime PM management
+    - bpf: Fix slot type check in check_stack_write_var_off
+    - media: vivid: fix compose size exceed boundary
+    - media: platform: exynos4-is: fix return value check in fimc_md_probe()
+    - bpf: propagate precision in ALU/ALU64 operations
+    - bpf: Check the other end of slot_type for STACK_SPILL
+    - bpf: propagate precision across all frames, not just the last one
+    - clk: qcom: gcc-sm8250: Use retention mode for USB GDSCs
+    - mtd: Fix device name leak when register device failed in add_mtd_device()
+    - Input: joystick - fix Kconfig warning for JOYSTICK_ADC
+    - wifi: rsi: Fix handling of 802.3 EAPOL frames sent via control port
+    - media: camss: Clean up received buffers on failed start of streaming
+    - net, proc: Provide PROC_FS=n fallback for proc_create_net_single_write()
+    - rxrpc: Fix ack.bufferSize to be 0 when generating an ack
+    - bfq: fix waker_bfqq inconsistency crash
+    - drm/radeon: Add the missed acpi_put_table() to fix memory leak
+    - drm/mediatek: Modify dpi power on/off sequence.
+    - ASoC: pxa: fix null-pointer dereference in filter()
+    - libbpf: Fix uninitialized warning in btf_dump_dump_type_data
+    - nvmet: only allocate a single slab for bvecs
+    - regulator: core: fix unbalanced of node refcount in regulator_dev_lookup()
+    - amdgpu/pm: prevent array underflow in vega20_odn_edit_dpm_table()
+    - nvme: return err on nvme_init_non_mdts_limits fail
+    - regulator: qcom-rpmh: Fix PMR735a S3 regulator spec
+    - drm/fourcc: Add packed 10bit YUV 4:2:0 format
+    - drm/fourcc: Fix vsub/hsub for Q410 and Q401
+    - integrity: Fix memory leakage in keyring allocation error path
+    - ima: Fix misuse of dereference of pointer in template_desc_init_fields()
+    - block: clear ->slave_dir when dropping the main slave_dir reference
+    - wifi: ath10k: Fix return value in ath10k_pci_init()
+    - drm/msm/a6xx: Fix speed-bin detection vs probe-defer
+    - mtd: lpddr2_nvm: Fix possible null-ptr-deref
+    - Input: elants_i2c - properly handle the reset GPIO when power is off
+    - media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init()
+    - media: solo6x10: fix possible memory leak in solo_sysfs_init()
+    - media: platform: exynos4-is: Fix error handling in fimc_md_init()
+    - media: videobuf-dma-contig: use dma_mmap_coherent
+    - inet: add READ_ONCE(sk->sk_bound_dev_if) in inet_csk_bind_conflict()
+    - mtd: spi-nor: hide jedec_id sysfs attribute if not present
+    - mtd: spi-nor: Fix the number of bytes for the dummy cycles
+    - bpf: Move skb->len == 0 checks into __bpf_redirect
+    - HID: hid-sensor-custom: set fixed size for custom attributes
+    - pinctrl: k210: call of_node_put()
+    - ALSA: pcm: fix undefined behavior in bit shift for SNDRV_PCM_RATE_KNOT
+    - ALSA: seq: fix undefined behavior in bit shift for
+      SNDRV_SEQ_FILTER_USE_EVENT
+    - regulator: core: use kfree_const() to free space conditionally
+    - clk: rockchip: Fix memory leak in rockchip_clk_register_pll()
+    - drm/amdgpu: fix pci device refcount leak
+    - bonding: fix link recovery in mode 2 when updelay is nonzero
+    - mtd: maps: pxa2xx-flash: fix memory leak in probe
+    - drbd: remove call to memset before free device/resource/connection
+    - drbd: destroy workqueue when drbd device was freed
+    - ASoC: qcom: Add checks for devm_kcalloc
+    - media: vimc: Fix wrong function called when vimc_init() fails
+    - media: imon: fix a race condition in send_packet()
+    - clk: imx8mn: rename vpu_pll to m7_alt_pll
+    - clk: imx: replace osc_hdmi with dummy
+    - clk: imx8mn: fix imx8mn_sai2_sels clocks list
+    - clk: imx8mn: fix imx8mn_enet_phy_sels clocks list
+    - pinctrl: pinconf-generic: add missing of_node_put()
+    - media: dvb-core: Fix ignored return value in dvb_register_frontend()
+    - media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()
+    - media: s5p-mfc: Add variant data for MFC v7 hardware for Exynos 3250 SoC
+    - drm/tegra: Add missing clk_disable_unprepare() in tegra_dc_probe()
+    - ASoC: dt-bindings: wcd9335: fix reset line polarity in example
+    - ASoC: mediatek: mtk-btcvsd: Add checks for write and read of mtk_btcvsd_snd
+    - NFSv4.2: Clear FATTR4_WORD2_SECURITY_LABEL when done decoding
+    - NFSv4.2: Fix a memory stomp in decode_attr_security_label
+    - NFSv4.2: Fix initialisation of struct nfs4_label
+    - NFSv4: Fix a credential leak in _nfs4_discover_trunking()
+    - NFSv4: Fix a deadlock between nfs4_open_recover_helper() and delegreturn
+    - NFS: Fix an Oops in nfs_d_automount()
+    - ALSA: asihpi: fix missing pci_disable_device()
+    - wifi: iwlwifi: mvm: fix double free on tx path.
+    - ASoC: mediatek: mt8173: Fix debugfs registration for components
+    - ASoC: mediatek: mt8173: Enable IRQ when pdata is ready
+    - drm/amd/pm/smu11: BACO is supported when it's in BACO state
+    - drm/radeon: Fix PCI device refcount leak in radeon_atrm_get_bios()
+    - drm/amdgpu: Fix PCI device refcount leak in amdgpu_atrm_get_bios()
+    - drm/amdkfd: Fix memory leakage
+    - ASoC: pcm512x: Fix PM disable depth imbalance in pcm512x_probe
+    - netfilter: conntrack: set icmpv6 redirects as RELATED
+    - Input: wistron_btns - disable on UML
+    - bpf, sockmap: Fix repeated calls to sock_put() when msg has more_data
+    - bpf, sockmap: Fix missing BPF_F_INGRESS flag when using apply_bytes
+    - bpf, sockmap: Fix data loss caused by using apply_bytes on ingress redirect
+    - bonding: uninitialized variable in bond_miimon_inspect()
+    - spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
+    - wifi: cfg80211: Fix not unregister reg_pdev when load_builtin_regdb_keys()
+      fails
+    - mt76: stop the radar detector after leaving dfs channel
+    - wifi: mt76: mt7921: fix reporting of TX AGGR histogram
+    - wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
+    - regulator: core: fix module refcount leak in set_supply()
+    - clk: qcom: lpass-sc7180: Fix pm_runtime usage
+    - clk: qcom: clk-krait: fix wrong div2 functions
+    - hsr: Add a rcu-read lock to hsr_forward_skb().
+    - hsr: Avoid double remove of a node.
+    - hsr: Disable netpoll.
+    - hsr: Synchronize sending frames to have always incremented outgoing seq nr.
+    - hsr: Synchronize sequence number updates.
+    - configfs: fix possible memory leak in configfs_create_dir()
+    - regulator: core: fix resource leak in regulator_register()
+    - hwmon: (jc42) Convert register access and caching to regmap/regcache
+    - hwmon: (jc42) Restore the min/max/critical temperatures on resume
+    - bpf, sockmap: fix race in sock_map_free()
+    - ALSA: pcm: Set missing stop_operating flag at undoing trigger start
+    - media: saa7164: fix missing pci_disable_device()
+    - ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
+    - xprtrdma: Fix regbuf data not freed in rpcrdma_req_create()
+    - SUNRPC: Fix missing release socket in rpc_sockname()
+    - NFSv4.x: Fail client initialisation if state manager thread can't run
+    - riscv, bpf: Emit fixed-length instructions for BPF_PSEUDO_FUNC
+    - mmc: alcor: fix return value check of mmc_add_host()
+    - mmc: moxart: fix return value check of mmc_add_host()
+    - mmc: mxcmmc: fix return value check of mmc_add_host()
+    - mmc: pxamci: fix return value check of mmc_add_host()
+    - mmc: rtsx_pci: fix return value check of mmc_add_host()
+    - mmc: rtsx_usb_sdmmc: fix return value check of mmc_add_host()
+    - mmc: toshsd: fix return value check of mmc_add_host()
+    - mmc: vub300: fix return value check of mmc_add_host()
+    - mmc: wmt-sdmmc: fix return value check of mmc_add_host()
+    - mmc: atmel-mci: fix return value check of mmc_add_host()
+    - mmc: omap_hsmmc: fix return value check of mmc_add_host()
+    - mmc: meson-gx: fix return value check of mmc_add_host()
+    - mmc: via-sdmmc: fix return value check of mmc_add_host()
+    - mmc: wbsd: fix return value check of mmc_add_host()
+    - mmc: mmci: fix return value check of mmc_add_host()
+    - mmc: renesas_sdhi: alway populate SCC pointer
+    - memstick: ms_block: Add error handling support for add_disk()
+    - memstick/ms_block: Add check for alloc_ordered_workqueue
+    - mmc: core: Normalize the error handling branch in sd_read_ext_regs()
+    - regulator: qcom-labibb: Fix missing of_node_put() in
+      qcom_labibb_regulator_probe()
+    - media: c8sectpfe: Add of_node_put() when breaking out of loop
+    - media: coda: Add check for dcoda_iram_alloc
+    - media: coda: Add check for kmalloc
+    - clk: samsung: Fix memory leak in _samsung_clk_register_pll()
+    - spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
+    - wifi: rtl8xxxu: Add __packed to struct rtl8723bu_c2h
+    - wifi: rtl8xxxu: Fix the channel width reporting
+    - wifi: brcmfmac: Fix error return code in brcmf_sdio_download_firmware()
+    - blktrace: Fix output non-blktrace event when blk_classic option enabled
+    - bpf: Do not zero-extend kfunc return values
+    - clk: socfpga: Fix memory leak in socfpga_gate_init()
+    - net: vmw_vsock: vmci: Check memcpy_from_msg()
+    - net: defxx: Fix missing err handling in dfx_init()
+    - net: stmmac: selftests: fix potential memleak in stmmac_test_arpoffload()
+    - net: stmmac: fix possible memory leak in stmmac_dvr_probe()
+    - drivers: net: qlcnic: Fix potential memory leak in qlcnic_sriov_init()
+    - of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry()
+      and find_dup_cset_prop()
+    - ethernet: s2io: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: farsync: Fix kmemleak when rmmods farsync
+    - net/tunnel: wait until all sk_user_data reader finish before releasing the
+      sock
+    - net: apple: mace: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: apple: bmac: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: emaclite: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: ethernet: dnet: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - hamradio: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - net: amd: lance: don't call dev_kfree_skb() under spin_lock_irqsave()
+    - af_unix: call proto_unregister() in the error path in af_unix_init()
+    - net: amd-xgbe: Fix logic around active and passive cables
+    - net: amd-xgbe: Check only the minimum speed for active/passive cables
+    - can: tcan4x5x: Remove invalid write in clear_interrupts
+    - can: m_can: Call the RAM init directly from m_can_chip_config
+    - can: tcan4x5x: Fix use of register error status mask
+    - net: lan9303: Fix read error execution path
+    - ntb_netdev: Use dev_kfree_skb_any() in interrupt context
+    - sctp: sysctl: make extra pointers netns aware
+    - Bluetooth: MGMT: Fix error report for ADD_EXT_ADV_PARAMS
+    - Bluetooth: btintel: Fix missing free skb in btintel_setup_combined()
+    - Bluetooth: btusb: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_qca: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_ll: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_h5: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_bcsp: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: hci_core: don't call kfree_skb() under spin_lock_irqsave()
+    - Bluetooth: RFCOMM: don't call kfree_skb() under spin_lock_irqsave()
+    - stmmac: fix potential division by 0
+    - i40e: Fix the inability to attach XDP program on downed interface
+    - net: dsa: tag_8021q: avoid leaking ctx on dsa_tag_8021q_register() error
+      path
+    - apparmor: fix a memleak in multi_transaction_new()
+    - apparmor: fix lockdep warning when removing a namespace
+    - apparmor: Fix abi check to include v8 abi
+    - crypto: hisilicon/qm - fix missing destroy qp_idr
+    - crypto: sun8i-ss - use dma_addr instead u32
+    - crypto: nitrox - avoid double free on error path in nitrox_sriov_init()
+    - scsi: core: Fix a race between scsi_done() and scsi_timeout()
+    - apparmor: Use pointer to struct aa_label for lbs_cred
+    - PCI: dwc: Fix n_fts[] array overrun
+    - RDMA/core: Fix order of nldev_exit call
+    - PCI: pci-epf-test: Register notifier if only core_init_notifier is enabled
+    - f2fs: Fix the race condition of resize flag between resizefs
+    - crypto: rockchip - do not do custom power management
+    - crypto: rockchip - do not store mode globally
+    - crypto: rockchip - add fallback for cipher
+    - crypto: rockchip - add fallback for ahash
+    - crypto: rockchip - better handle cipher key
+    - crypto: rockchip - remove non-aligned handling
+    - crypto: rockchip - rework by using crypto_engine
+    - apparmor: Fix memleak in alloc_ns()
+    - f2fs: fix to invalidate dcc->f2fs_issue_discard in error path
+    - f2fs: fix normal discard process
+    - f2fs: fix to destroy sbi->post_read_wq in error path of f2fs_fill_super()
+    - RDMA/irdma: Report the correct link speed
+    - scsi: qla2xxx: Fix set-but-not-used variable warnings
+    - RDMA/siw: Fix immediate work request flush to completion queue
+    - IB/mad: Don't call to function that might sleep while in atomic context
+    - RDMA/restrack: Release MR restrack when delete
+    - RDMA/core: Make sure "ib_port" is valid when access sysfs node
+    - RDMA/nldev: Return "-EAGAIN" if the cm_id isn't from expected port
+    - RDMA/siw: Set defined status for work completion with undefined status
+    - scsi: scsi_debug: Fix a warning in resp_write_scat()
+    - crypto: ccree - Remove debugfs when platform_driver_register failed
+    - crypto: cryptd - Use request context instead of stack for sub-request
+    - crypto: hisilicon/qm - add missing pci_dev_put() in q_num_set()
+    - RDMA/hns: Repacing 'dseg_len' by macros in fill_ext_sge_inl_data()
+    - RDMA/hns: Fix ext_sge num error when post send
+    - PCI: Check for alloc failure in pci_request_irq()
+    - RDMA/hfi: Decrease PCI device reference count in error path
+    - crypto: ccree - Make cc_debugfs_global_fini() available for module init
+      function
+    - RDMA/hns: fix memory leak in hns_roce_alloc_mr()
+    - RDMA/rxe: Fix NULL-ptr-deref in rxe_qp_do_cleanup() when socket create
+      failed
+    - dt-bindings: imx6q-pcie: Fix clock names for imx6sx and imx8mq
+    - dt-bindings: visconti-pcie: Fix interrupts array max constraints
+    - scsi: hpsa: Fix possible memory leak in hpsa_init_one()
+    - crypto: tcrypt - Fix multibuffer skcipher speed test mem leak
+    - padata: Always leave BHs disabled when running ->parallel()
+    - padata: Fix list iterator in padata_do_serial()
+    - scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add()
+    - scsi: hpsa: Fix error handling in hpsa_add_sas_host()
+    - scsi: hpsa: Fix possible memory leak in hpsa_add_sas_device()
+    - scsi: efct: Fix possible memleak in efct_device_init()
+    - scsi: scsi_debug: Fix a warning in resp_verify()
+    - scsi: scsi_debug: Fix a warning in resp_report_zones()
+    - scsi: fcoe: Fix possible name leak when device_register() fails
+    - scsi: scsi_debug: Fix possible name leak in sdebug_add_host_helper()
+    - scsi: ipr: Fix WARNING in ipr_init()
+    - scsi: fcoe: Fix transport not deattached when fcoe_if_init() fails
+    - scsi: snic: Fix possible UAF in snic_tgt_create()
+    - RDMA/nldev: Add checks for nla_nest_start() in fill_stat_counter_qps()
+    - f2fs: avoid victim selection from previous victim section
+    - RDMA/nldev: Fix failure to send large messages
+    - crypto: amlogic - Remove kcalloc without check
+    - crypto: omap-sham - Use pm_runtime_resume_and_get() in omap_sham_probe()
+    - riscv/mm: add arch hook arch_clear_hugepage_flags
+    - RDMA/hfi1: Fix error return code in parse_platform_config()
+    - RDMA/srp: Fix error return code in srp_parse_options()
+    - PCI: mt7621: Rename mt7621_pci_ to mt7621_pcie_
+    - PCI: mt7621: Add sentinel to quirks table
+    - orangefs: Fix sysfs not cleanup when dev init failed
+    - RDMA/hns: Fix AH attr queried by query_qp
+    - RDMA/hns: Fix PBL page MTR find
+    - RDMA/hns: Fix page size cap from firmware
+    - RDMA/hns: Fix error code of CMD
+    - crypto: img-hash - Fix variable dereferenced before check 'hdev->req'
+    - hwrng: amd - Fix PCI device refcount leak
+    - hwrng: geode - Fix PCI device refcount leak
+    - IB/IPoIB: Fix queue count inconsistency for PKEY child interfaces
+    - RISC-V: Align the shadow stack
+    - drivers: dio: fix possible memory leak in dio_init()
+    - serial: tegra: Read DMA status before terminating
+    - serial: 8250_bcm7271: Fix error handling in brcmuart_init()
+    - class: fix possible memory leak in __class_register()
+    - vfio: platform: Do not pass return buffer to ACPI _RST method
+    - uio: uio_dmem_genirq: Fix missing unlock in irq configuration
+    - uio: uio_dmem_genirq: Fix deadlock between irq config and handling
+    - usb: fotg210-udc: Fix ages old endianness issues
+    - staging: vme_user: Fix possible UAF in tsi148_dma_list_add
+    - usb: typec: Check for ops->exit instead of ops->enter in altmode_exit
+    - usb: typec: tcpci: fix of node refcount leak in tcpci_register_port()
+    - usb: typec: tipd: Cleanup resources if devm_tps6598_psy_register fails
+    - usb: typec: tipd: Fix spurious fwnode_handle_put in error path
+    - extcon: usbc-tusb320: Add support for mode setting and reset
+    - extcon: usbc-tusb320: Add support for TUSB320L
+    - usb: typec: Factor out non-PD fwnode properties
+    - extcon: usbc-tusb320: Factor out extcon into dedicated functions
+    - extcon: usbc-tusb320: Add USB TYPE-C support
+    - extcon: usbc-tusb320: Update state on probe even if no IRQ pending
+    - serial: amba-pl011: avoid SBSA UART accessing DMACR register
+    - serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
+    - serial: stm32: move dma_request_chan() before clk_prepare_enable()
+    - serial: pch: Fix PCI device refcount leak in pch_request_dma()
+    - tty: serial: clean up stop-tx part in altera_uart_tx_chars()
+    - tty: serial: altera_uart_{r,t}x_chars() need only uart_port
+    - serial: altera_uart: fix locking in polling mode
+    - serial: sunsab: Fix error handling in sunsab_init()
+    - test_firmware: fix memory leak in test_firmware_init()
+    - misc: ocxl: fix possible name leak in ocxl_file_register_afu()
+    - ocxl: fix pci device refcount leak when calling get_function_0()
+    - misc: tifm: fix possible memory leak in tifm_7xx1_switch_media()
+    - misc: sgi-gru: fix use-after-free error in gru_set_context_option, gru_fault
+      and gru_handle_user_call_os
+    - firmware: raspberrypi: fix possible memory leak in rpi_firmware_probe()
+    - cxl: fix possible null-ptr-deref in cxl_guest_init_afu|adapter()
+    - cxl: fix possible null-ptr-deref in cxl_pci_init_afu|adapter()
+    - iio: temperature: ltc2983: make bulk write buffer DMA-safe
+    - iio: adis: handle devices that cannot unmask the drdy pin
+    - iio: adis: stylistic changes
+    - iio:imu:adis: Move exports into IIO_ADISLIB namespace
+    - iio: adis: add '__adis_enable_irq()' implementation
+    - counter: stm32-lptimer-cnt: fix the check on arr and cmp registers update
+    - coresight: trbe: remove cpuhp instance node before remove cpuhp state
+    - usb: roles: fix of node refcount leak in usb_role_switch_is_parent()
+    - usb: gadget: f_hid: fix f_hidg lifetime vs cdev
+    - usb: gadget: f_hid: fix refcount leak on error path
+    - drivers: mcb: fix resource leak in mcb_probe()
+    - mcb: mcb-parse: fix error handing in chameleon_parse_gdd()
+    - chardev: fix error handling in cdev_device_add()
+    - i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
+    - staging: rtl8192u: Fix use after free in ieee80211_rx()
+    - staging: rtl8192e: Fix potential use-after-free in rtllib_rx_Monitor()
+    - vme: Fix error not catched in fake_init()
+    - gpiolib: Get rid of redundant 'else'
+    - gpiolib: cdev: fix NULL-pointer dereferences
+    - gpiolib: make struct comments into real kernel docs
+    - gpiolib: protect the GPIO device against being dropped while in use by user-
+      space
+    - i2c: mux: reg: check return value after calling platform_get_resource()
+    - i2c: ismt: Fix an out-of-bounds bug in ismt_access()
+    - usb: storage: Add check for kcalloc
+    - tracing/hist: Fix issue of losting command info in error_log
+    - ksmbd: Fix resource leak in ksmbd_session_rpc_open()
+    - samples: vfio-mdev: Fix missing pci_disable_device() in mdpy_fb_probe()
+    - thermal/drivers/imx8mm_thermal: Validate temperature range
+    - thermal/drivers/qcom/temp-alarm: Fix inaccurate warning for gen2
+    - thermal/drivers/qcom/lmh: Fix irq handler return value
+    - fbdev: ssd1307fb: Drop optional dependency
+    - fbdev: pm2fb: fix missing pci_disable_device()
+    - fbdev: via: Fix error in via_core_init()
+    - fbdev: vermilion: decrease reference count in error path
+    - fbdev: ep93xx-fb: Add missing clk_disable_unprepare in ep93xxfb_probe()
+    - fbdev: geode: don't build on UML
+    - fbdev: uvesafb: don't build on UML
+    - fbdev: uvesafb: Fixes an error handling path in uvesafb_probe()
+    - HSI: omap_ssi_core: fix unbalanced pm_runtime_disable()
+    - HSI: omap_ssi_core: fix possible memory leak in ssi_probe()
+    - power: supply: fix residue sysfs file in error handle route of
+      __power_supply_register()
+    - perf trace: Return error if a system call doesn't exist
+    - perf trace: Use macro RAW_SYSCALL_ARGS_NUM to replace number
+    - perf trace: Handle failure when trace point folder is missed
+    - perf symbol: correction while adjusting symbol
+    - power: supply: z2_battery: Fix possible memleak in z2_batt_probe()
+    - HSI: omap_ssi_core: Fix error handling in ssi_init()
+    - power: supply: ab8500: Fix error handling in ab8500_charger_init()
+    - power: supply: fix null pointer dereferencing in
+      power_supply_get_battery_info
+    - perf stat: Refactor __run_perf_stat() common code
+    - perf stat: Do not delay the workload with --delay
+    - RDMA/siw: Fix pointer cast warning
+    - fs/ntfs3: Avoid UBSAN error on true_sectors_per_clst()
+    - overflow: Implement size_t saturating arithmetic helpers
+    - fs/ntfs3: Harden against integer overflows
+    - iommu/sun50i: Fix reset release
+    - iommu/sun50i: Consider all fault sources for reset
+    - iommu/sun50i: Fix R/W permission check
+    - iommu/sun50i: Fix flush size
+    - iommu/rockchip: fix permission bits in page table entries v2
+    - phy: usb: s2 WoL wakeup_count not incremented for USB->Eth devices
+    - include/uapi/linux/swab: Fix potentially missing __always_inline
+    - pwm: tegra: Improve required rate calculation
+    - fs/ntfs3: Fix slab-out-of-bounds read in ntfs_trim_fs
+    - dmaengine: idxd: Fix crc_val field for completion record
+    - rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0
+    - rtc: cmos: Fix event handler registration ordering issue
+    - rtc: cmos: Fix wake alarm breakage
+    - rtc: cmos: fix build on non-ACPI platforms
+    - rtc: cmos: Call cmos_wake_setup() from cmos_do_probe()
+    - rtc: cmos: Call rtc_wake_setup() from cmos_do_probe()
+    - rtc: cmos: Eliminate forward declarations of some functions
+    - rtc: cmos: Rename ACPI-related functions
+    - rtc: cmos: Disable ACPI RTC event on removal
+    - rtc: snvs: Allow a time difference on clock register read
+    - rtc: pcf85063: Fix reading alarm
+    - iommu/amd: Fix pci device refcount leak in ppr_notifier()
+    - iommu/fsl_pamu: Fix resource leak in fsl_pamu_probe()
+    - macintosh: fix possible memory leak in macio_add_one_device()
+    - macintosh/macio-adb: check the return value of ioremap()
+    - powerpc/52xx: Fix a resource leak in an error handling path
+    - cxl: Fix refcount leak in cxl_calc_capp_routing
+    - powerpc/xmon: Fix -Wswitch-unreachable warning in bpt_cmds
+    - powerpc/xive: add missing iounmap() in error path in
+      xive_spapr_populate_irq_data()
+    - powerpc/perf: callchain validate kernel stack pointer bounds
+    - powerpc/83xx/mpc832x_rdb: call platform_device_put() in error case in
+      of_fsl_spi_probe()
+    - powerpc/hv-gpci: Fix hv_gpci event list
+    - selftests/powerpc: Fix resource leaks
+    - iommu/sun50i: Remove IOMMU_DOMAIN_IDENTITY
+    - pwm: sifive: Call pwm_sifive_update_clock() while mutex is held
+    - pwm: mtk-disp: Fix the parameters calculated by the enabled flag of disp_pwm
+    - pwm: mediatek: always use bus clock for PWM on MT7622
+    - remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()
+    - remoteproc: qcom: q6v5: Fix potential null-ptr-deref in
+      q6v5_wcss_init_mmio()
+    - remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove
+    - remoteproc: qcom_q6v5_pas: detach power domains on remove
+    - remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in
+      adsp_alloc_memory_region()
+    - remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in
+      q6v5_wcss_qcs404_power_on()
+    - powerpc/eeh: Drop redundant spinlock initialization
+    - powerpc/pseries/eeh: use correct API for error log size
+    - mfd: bd957x: Fix Kconfig dependency on REGMAP_IRQ
+    - mfd: qcom_rpm: Fix an error handling path in qcom_rpm_probe()
+    - mfd: pm8008: Remove driver data structure pm8008_data
+    - mfd: pm8008: Fix return value check in pm8008_probe()
+    - netfilter: flowtable: really fix NAT IPv6 offload
+    - rtc: st-lpc: Add missing clk_disable_unprepare in st_rtc_probe()
+    - rtc: pic32: Move devm_rtc_allocate_device earlier in pic32_rtc_probe()
+    - rtc: pcf85063: fix pcf85063_clkout_control
+    - nfsd: under NFSv4.1, fix double svc_xprt_put on rpc_create failure
+    - net: macsec: fix net device access prior to holding a lock
+    - mISDN: hfcsusb: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - mISDN: hfcpci: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - mISDN: hfcmulti: don't call dev_kfree_skb/kfree_skb() under
+      spin_lock_irqsave()
+    - block, bfq: fix possible uaf for 'bfqq->bic'
+    - net: enetc: avoid buffer leaks on xdp_do_redirect() failure
+    - nfc: pn533: Clear nfc_target before being used
+    - unix: Fix race in SOCK_SEQPACKET's unix_dgram_sendmsg()
+    - r6040: Fix kmemleak in probe and remove
+    - igc: Enhance Qbv scheduling by using first flag bit
+    - igc: Use strict cycles for Qbv scheduling
+    - igc: Add checking for basetime less than zero
+    - igc: allow BaseTime 0 enrollment for Qbv
+    - igc: recalculate Qbv end_time by considering cycle time
+    - igc: Lift TAPRIO schedule restriction
+    - igc: Set Qbv start_time and end_time to end_time if not being configured in
+      GCL
+    - rtc: mxc_v2: Add missing clk_disable_unprepare()
+    - selftests: devlink: fix the fd redirect in dummy_reporter_test
+    - openvswitch: Fix flow lookup to use unmasked key
+    - soc: mediatek: pm-domains: Fix the power glitch issue
+    - arm64: dts: mt8183: Fix Mali GPU clock
+    - skbuff: Account for tail adjustment during pull operations
+    - mailbox: mpfs: read the system controller's status
+    - mailbox: arm_mhuv2: Fix return value check in mhuv2_probe()
+    - mailbox: zynq-ipi: fix error handling while device_register() fails
+    - net_sched: reject TCF_EM_SIMPLE case for complex ematch module
+    - rxrpc: Fix missing unlock in rxrpc_do_sendmsg()
+    - myri10ge: Fix an error handling path in myri10ge_probe()
+    - net: stream: purge sk_error_queue in sk_stream_kill_queues()
+    - HID: amd_sfh: Add missing check for dma_alloc_coherent
+    - rcu: Fix __this_cpu_read() lockdep warning in rcu_force_quiescent_state()
+    - arm64: make is_ttbrX_addr() noinstr-safe
+    - video: hyperv_fb: Avoid taking busy spinlock on panic path
+    - x86/hyperv: Remove unregister syscore call from Hyper-V cleanup
+    - binfmt_misc: fix shift-out-of-bounds in check_special_flags
+    - fs: jfs: fix shift-out-of-bounds in dbAllocAG
+    - udf: Avoid double brelse() in udf_rename()
+    - jfs: Fix fortify moan in symlink
+    - fs: jfs: fix shift-out-of-bounds in dbDiscardAG
+    - ACPICA: Fix error code path in acpi_ds_call_control_method()
+    - nilfs2: fix shift-out-of-bounds/overflow in nilfs_sb2_bad_offset()
+    - nilfs2: fix shift-out-of-bounds due to too large exponent of block size
+    - acct: fix potential integer overflow in encode_comp_t()
+    - hfs: fix OOB Read in __hfs_brec_find
+    - drm/etnaviv: add missing quirks for GC300
+    - media: imx-jpeg: Disable useless interrupt to avoid kernel panic
+    - brcmfmac: return error when getting invalid max_flowrings from dongle
+    - wifi: ath9k: verify the expected usb_endpoints are present
+    - wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
+    - ASoC: codecs: rt298: Add quirk for KBL-R RVP platform
+    - ipmi: fix memleak when unload ipmi driver
+    - drm/amd/display: prevent memory leak
+    - Revert "drm/amd/display: Limit max DSC target bpp for specific monitors"
+    - qed (gcc13): use u16 for fid to be big enough
+    - bpf: make sure skb->len != 0 when redirecting to a tunneling device
+    - net: ethernet: ti: Fix return type of netcp_ndo_start_xmit()
+    - hamradio: baycom_epp: Fix return type of baycom_send_packet()
+    - wifi: brcmfmac: Fix potential shift-out-of-bounds in
+      brcmf_fw_alloc_request()
+    - igb: Do not free q_vector unless new one was allocated
+    - drm/amdgpu: Fix type of second parameter in trans_msg() callback
+    - drm/amdgpu: Fix type of second parameter in odn_edit_dpm_table() callback
+    - s390/ctcm: Fix return type of ctc{mp,}m_tx()
+    - s390/netiucv: Fix return type of netiucv_tx()
+    - s390/lcs: Fix return type of lcs_start_xmit()
+    - drm/msm: Use drm_mode_copy()
+    - drm/rockchip: Use drm_mode_copy()
+    - drm/sti: Use drm_mode_copy()
+    - drm/mediatek: Fix return type of mtk_hdmi_bridge_mode_valid()
+    - drivers/md/md-bitmap: check the return value of md_bitmap_get_counter()
+    - md/raid1: stop mdx_raid1 thread when raid1 array run failed
+    - drm/amd/display: fix array index out of bound error in bios parser
+    - net: add atomic_long_t to net_device_stats fields
+    - ipv6/sit: use DEV_STATS_INC() to avoid data-races
+    - mrp: introduce active flags to prevent UAF when applicant uninit
+    - ppp: associate skb with a device at tx
+    - bpf: Prevent decl_tag from being referenced in func_proto arg
+    - ethtool: avoiding integer overflow in ethtool_phys_id()
+    - media: dvb-frontends: fix leak of memory fw
+    - media: dvbdev: adopts refcnt to avoid UAF
+    - media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
+    - blk-mq: fix possible memleak when register 'hctx' failed
+    - drm/amd/display: Use the largest vready_offset in pipe group
+    - libbpf: Avoid enum forward-declarations in public API in C++ mode
+    - regulator: core: fix use_count leakage when handling boot-on
+    - wifi: mt76: do not run mt76u_status_worker if the device is not running
+    - mmc: f-sdh30: Add quirks for broken timeout clock capability
+    - mmc: renesas_sdhi: better reset from HS400 mode
+    - media: si470x: Fix use-after-free in si470x_int_in_callback()
+    - clk: st: Fix memory leak in st_of_quadfs_setup()
+    - crypto: hisilicon/hpre - fix resource leak in remove process
+    - scsi: lpfc: Fix hard lockup when reading the rx_monitor from debugfs
+    - scsi: ufs: Reduce the START STOP UNIT timeout
+    - scsi: elx: libefc: Fix second parameter type in state callbacks
+    - hugetlbfs: fix null-ptr-deref in hugetlbfs_parse_param()
+    - drm/fsl-dcu: Fix return type of fsl_dcu_drm_connector_mode_valid()
+    - drm/sti: Fix return type of sti_{dvo,hda,hdmi}_connector_mode_valid()
+    - orangefs: Fix kmemleak in orangefs_prepare_debugfs_help_string()
+    - orangefs: Fix kmemleak in orangefs_{kernel,client}_debug_init()
+    - tools/include: Add _RET_IP_ and math definitions to kernel.h
+    - KVM: selftests: Fix build regression by using accessor function
+    - hwmon: (jc42) Fix missing unlock on error in jc42_write()
+    - ALSA/ASoC: hda: move/rename snd_hdac_ext_stop_streams to hdac_stream.c
+    - ALSA: hda: add snd_hdac_stop_streams() helper
+    - ASoC: Intel: Skylake: Fix driver hang during shutdown
+    - ASoC: mediatek: mt8173-rt5650-rt5514: fix refcount leak in
+      mt8173_rt5650_rt5514_dev_probe()
+    - ASoC: audio-graph-card: fix refcount leak of cpu_ep in
+      __graph_for_each_link()
+    - ASoC: rockchip: pdm: Add missing clk_disable_unprepare() in
+      rockchip_pdm_runtime_resume()
+    - ASoC: mediatek: mt8183: fix refcount leak in
+      mt8183_mt6358_ts3a227_max98357_dev_probe()
+    - ASoC: wm8994: Fix potential deadlock
+    - ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in
+      rk_spdif_runtime_resume()
+    - ASoC: rt5670: Remove unbalanced pm_runtime_put()
+    - drm/i915/display: Don't disable DDI/Transcoder when setting phy test pattern
+    - LoadPin: Ignore the "contents" argument of the LSM hooks
+    - pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion
+    - perf debug: Set debug_peo_args and redirect_to_stderr variable to correct
+      values in perf_quiet_option()
+    - afs: Fix lost servers_outstanding count
+    - pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
+    - ALSA: usb-audio: add the quirk for KT0206 device
+    - ALSA: hda/realtek: Add quirk for Lenovo TianYi510Pro-14IOB
+    - ALSA: hda/hdmi: Add HP Device 0x8711 to force connect list
+    - usb: cdnsp: fix lack of ZLP for ep0
+    - usb: xhci-mtk: fix leakage of shared hcd when fail to set wakeup irq
+    - arm64: dts: qcom: sm8250: fix USB-DP PHY registers
+    - usb: dwc3: Fix race between dwc3_set_mode and __dwc3_set_mode
+    - usb: dwc3: core: defer probe on ulpi_read_id timeout
+    - xhci: Prevent infinite loop in transaction errors recovery for streams
+    - HID: wacom: Ensure bootloader PID is usable in hidraw mode
+    - HID: mcp2221: don't connect hidraw
+    - loop: Fix the max_loop commandline argument treatment when it is set to 0
+    - 9p: set req refcount to zero to avoid uninitialized usage
+    - security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
+    - reiserfs: Add missing calls to reiserfs_security_free()
+    - iio: fix memory leak in iio_device_register_eventset()
+    - iio: adc: ad_sigma_delta: do not use internal iio_dev lock
+    - iio: adc128s052: add proper .data members in adc128_of_match table
+    - regulator: core: fix deadlock on regulator enable
+    - floppy: Fix memory leak in do_floppy_init()
+    - gcov: add support for checksum field
+    - fbdev: fbcon: release buffer when fbcon_do_set_font() failed
+    - ovl: fix use inode directly in rcu-walk mode
+    - btrfs: do not BUG_ON() on ENOMEM when dropping extent items for a range
+    - scsi: qla2xxx: Fix crash when I/O abort times out
+    - net: stmmac: fix errno when create_singlethread_workqueue() fails
+    - media: dvbdev: fix build warning due to comments
+    - media: dvbdev: fix refcnt bug
+    - extcon: usbc-tusb320: Call the Type-C IRQ handler only if a port is
+      registered
+    - mfd: qcom_rpm: Use devm_of_platform_populate() to simplify code
+    - pwm: tegra: Fix 32 bit build
+    - Linux 5.15.86
+  * Screen freeze after resuming from suspend (nvme0: I/O timeout)
+    (LP: #1996048) // Jammy update: v5.15.86 upstream stable release
+    (LP: #2005113)
+    - PCI: vmd: Disable MSI remapping after suspend
+  * CVE-2023-23559
+    - wifi: rndis_wlan: Prevent buffer overflow in rndis_query_oid
+  * CVE-2023-0045
+    - x86/bugs: Flush IBP in ib_prctl_set()
+
+  [ Ubuntu: 5.15.0-67.74 ]
+
+  * jammy/linux: 5.15.0-67.74 -proposed tracker (LP: #2008074)
+  * [Inspiron 7590, Realtek ALC3254, Speaker, Internal] fails after a while
+    (LP: #2007798)
+    - Revert "ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()"
+
+  [ Ubuntu: 5.15.0-66.73 ]
+
+  * jammy/linux: 5.15.0-66.73 -proposed tracker (LP: #2004636)
+  * CVE-2023-0461
+    - SAUCE: Fix inet_csk_listen_start after CVE-2023-0461
+
+  [ Ubuntu: 5.15.0-65.72 ]
+
+  * jammy/linux: 5.15.0-65.72 -proposed tracker (LP: #2004344)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2023.01.30)
+  * NFS: client permission error after adding user to permissible group
+    (LP: #2003053)
+    - NFS: Clear the file access cache upon login
+    - NFS: Judge the file access cache's timestamp in rcu path
+    - NFS: Fix up a sparse warning
+  * Fix W6400 hang after resume of S3 stress (LP: #2000299)
+    - drm/amd/display: Manually adjust strobe for DCN303
+  * Rear Audio port sometimes has no audio output after reboot(Cirrus Logic)
+    (LP: #1998905)
+    - ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
+  * CVE-2022-20369
+    - NFSD: fix use-after-free in __nfs42_ssc_open()
+  * CVE-2023-0461
+    - net/ulp: prevent ULP without clone op from entering the LISTEN status
+    - net/ulp: use consistent error code when blocking ULP
+  * CVE-2023-0179
+    - netfilter: nft_payload: incorrect arithmetics when fetching VLAN header bits
+  * Jammy update: v5.15.85 upstream stable release (LP: #2003139)
+    - udf: Discard preallocation before extending file with a hole
+    - udf: Fix preallocation discarding at indirect extent boundary
+    - udf: Do not bother looking for prealloc extents if i_lenExtents matches
+      i_size
+    - udf: Fix extending file within last block
+    - usb: gadget: uvc: Prevent buffer overflow in setup handler
+    - USB: serial: option: add Quectel EM05-G modem
+    - USB: serial: cp210x: add Kamstrup RF sniffer PIDs
+    - USB: serial: f81232: fix division by zero on line-speed change
+    - USB: serial: f81534: fix division by zero on line-speed change
+    - xhci: Apply XHCI_RESET_TO_DEFAULT quirk to ADL-N
+    - igb: Initialize mailbox message for VF reset
+    - usb: dwc3: pci: Update PCIe device ID for USB3 controller on CPU sub-system
+      for Raptor Lake
+    - HID: uclogic: Add HID_QUIRK_HIDINPUT_FORCE quirk
+    - selftests: net: Use "grep -E" instead of "egrep"
+    - net: loopback: use NET_NAME_PREDICTABLE for name_assign_type
+    - Linux 5.15.85
+  * Jammy update: v5.15.84 upstream stable release (LP: #2003137)
+    - x86/vdso: Conditionally export __vdso_sgx_enter_enclave()
+    - vfs: fix copy_file_range() averts filesystem freeze protection
+    - ASoC: fsl_micfil: explicitly clear software reset bit
+    - ASoC: fsl_micfil: explicitly clear CHnF flags
+    - ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()
+    - libbpf: Use page size as max_entries when probing ring buffer map
+    - pinctrl: meditatek: Startup with the IRQs disabled
+    - can: sja1000: fix size of OCR_MODE_MASK define
+    - can: mcba_usb: Fix termination command argument
+    - net: fec: don't reset irq coalesce settings to defaults on "ip link up"
+    - ASoC: cs42l51: Correct PGA Volume minimum value
+    - perf: Fix perf_pending_task() UaF
+    - nvme-pci: clear the prp2 field when not used
+    - ASoC: ops: Correct bounds check for second channel on SX controls
+    - net: fec: properly guard irq coalesce setup
+    - Linux 5.15.84
+  * Jammy update: v5.15.83 upstream stable release (LP: #2003134)
+    - clk: generalize devm_clk_get() a bit
+    - clk: Provide new devm_clk helpers for prepared and enabled clocks
+    - mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()
+    - arm64: dts: rockchip: keep I2S1 disabled for GPIO function on ROCK Pi 4
+      series
+    - arm: dts: rockchip: fix node name for hym8563 rtc
+    - arm: dts: rockchip: remove clock-frequency from rtc
+    - ARM: dts: rockchip: fix ir-receiver node names
+    - arm64: dts: rockchip: fix ir-receiver node names
+    - ARM: dts: rockchip: rk3188: fix lcdc1-rgb24 node name
+    - fs: use acquire ordering in __fget_light()
+    - ARM: 9251/1: perf: Fix stacktraces for tracepoint events in THUMB2 kernels
+    - ARM: 9266/1: mm: fix no-MMU ZERO_PAGE() implementation
+    - ASoC: wm8962: Wait for updated value of WM8962_CLOCKING1 register
+    - spi: mediatek: Fix DEVAPC Violation at KO Remove
+    - ARM: dts: rockchip: disable arm_global_timer on rk3066 and rk3188
+    - ASoC: rt711-sdca: fix the latency time of clock stop prepare state machine
+      transitions
+    - 9p/fd: Use P9_HDRSZ for header size
+    - regulator: slg51000: Wait after asserting CS pin
+    - ALSA: seq: Fix function prototype mismatch in snd_seq_expand_var_event
+    - selftests/net: Find nettest in current directory
+    - btrfs: send: avoid unaligned encoded writes when attempting to clone range
+    - ASoC: soc-pcm: Add NULL check in BE reparenting
+    - regulator: twl6030: fix get status of twl6032 regulators
+    - fbcon: Use kzalloc() in fbcon_prepare_logo()
+    - usb: dwc3: gadget: Disable GUSB2PHYCFG.SUSPHY for End Transfer
+    - 9p/xen: check logical size for buffer size
+    - net: usb: qmi_wwan: add u-blox 0x1342 composition
+    - mm/khugepaged: take the right locks for page table retraction
+    - mm/khugepaged: fix GUP-fast interaction by sending IPI
+    - mm/khugepaged: invoke MMU notifiers in shmem/file collapse paths
+    - rtc: mc146818-lib: extract mc146818_avoid_UIP
+    - rtc: cmos: avoid UIP when writing alarm time
+    - rtc: cmos: avoid UIP when reading alarm time
+    - cifs: fix use-after-free caused by invalid pointer `hostname`
+    - drm/bridge: anx7625: Fix edid_read break case in sp_tx_edid_read()
+    - xen/netback: do some code cleanup
+    - xen/netback: don't call kfree_skb() with interrupts disabled
+    - media: videobuf2-core: take mmap_lock in vb2_get_unmapped_area()
+    - soundwire: intel: Initialize clock stop timeout
+    - media: v4l2-dv-timings.c: fix too strict blanking sanity checks
+    - memcg: fix possible use-after-free in memcg_write_event_control()
+    - mm/gup: fix gup_pud_range() for dax
+    - Bluetooth: btusb: Add debug message for CSR controllers
+    - Bluetooth: Fix crash when replugging CSR fake controllers
+    - net: mana: Fix race on per-CQ variable napi work_done
+    - KVM: s390: vsie: Fix the initialization of the epoch extension (epdx) field
+    - drm/vmwgfx: Don't use screen objects when SEV is active
+    - drm/amdgpu/sdma_v4_0: turn off SDMA ring buffer in the s2idle suspend
+    - drm/shmem-helper: Remove errant put in error path
+    - drm/shmem-helper: Avoid vm_open error paths
+    - net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
+    - HID: usbhid: Add ALWAYS_POLL quirk for some mice
+    - HID: hid-lg4ff: Add check for empty lbuf
+    - HID: core: fix shift-out-of-bounds in hid_report_raw_event
+    - HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10
+    - can: af_can: fix NULL pointer dereference in can_rcv_filter
+    - clk: Fix pointer casting to prevent oops in devm_clk_release()
+    - gpiolib: improve coding style for local variables
+    - gpiolib: check the 'ngpios' property in core gpiolib code
+    - gpiolib: fix memory leak in gpiochip_setup_dev()
+    - netfilter: nft_set_pipapo: Actually validate intervals in fields after the
+      first one
+    - drm/vmwgfx: Fix race issue calling pin_user_pages
+    - ieee802154: cc2520: Fix error return code in cc2520_hw_init()
+    - ca8210: Fix crash by zero initializing data
+    - netfilter: ctnetlink: fix compilation warning after data race fixes in ct
+      mark
+    - drm/bridge: ti-sn65dsi86: Fix output polarity setting bug
+    - gpio: amd8111: Fix PCI device reference count leak
+    - e1000e: Fix TX dispatch condition
+    - igb: Allocate MSI-X vector when testing
+    - net: broadcom: Add PTP_1588_CLOCK_OPTIONAL dependency for BCMGENET under
+      ARCH_BCM2835
+    - drm: bridge: dw_hdmi: fix preference of RGB modes over YUV420
+    - af_unix: Get user_ns from in_skb in unix_diag_get_exact().
+    - vmxnet3: correctly report encapsulated LRO packet
+    - vmxnet3: use correct intrConf reference when using extended queues
+    - Bluetooth: 6LoWPAN: add missing hci_dev_put() in get_l2cap_conn()
+    - Bluetooth: Fix not cleanup led when bt_init fails
+    - net: dsa: ksz: Check return value
+    - net: dsa: hellcreek: Check return value
+    - net: dsa: sja1105: Check return value
+    - selftests: rtnetlink: correct xfrm policy rule in kci_test_ipsec_offload
+    - mac802154: fix missing INIT_LIST_HEAD in ieee802154_if_add()
+    - net: encx24j600: Add parentheses to fix precedence
+    - net: encx24j600: Fix invalid logic in reading of MISTAT register
+    - net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
+    - net: mdiobus: fix double put fwnode in the error path
+    - octeontx2-pf: Fix potential memory leak in otx2_init_tc()
+    - xen-netfront: Fix NULL sring after live migration
+    - net: mvneta: Prevent out of bounds read in mvneta_config_rss()
+    - i40e: Fix not setting default xps_cpus after reset
+    - i40e: Fix for VF MAC address 0
+    - i40e: Disallow ip4 and ip6 l4_4_bytes
+    - NFC: nci: Bounds check struct nfc_target arrays
+    - nvme initialize core quirks before calling nvme_init_subsystem
+    - gpio/rockchip: fix refcount leak in rockchip_gpiolib_register()
+    - net: stmmac: fix "snps,axi-config" node property parsing
+    - ip_gre: do not report erspan version on GRE interface
+    - net: microchip: sparx5: Fix missing destroy_workqueue of mact_queue
+    - net: thunderx: Fix missing destroy_workqueue of nicvf_rx_mode_wq
+    - net: hisilicon: Fix potential use-after-free in hisi_femac_rx()
+    - net: mdio: fix unbalanced fwnode reference count in mdio_device_release()
+    - net: hisilicon: Fix potential use-after-free in hix5hd2_rx()
+    - tipc: Fix potential OOB in tipc_link_proto_rcv()
+    - ipv4: Fix incorrect route flushing when source address is deleted
+    - ipv4: Fix incorrect route flushing when table ID 0 is used
+    - net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()
+    - tipc: call tipc_lxc_xmit without holding node_read_lock
+    - ethernet: aeroflex: fix potential skb leak in greth_init_rings()
+    - dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and
+      dpaa2_switch_acl_entry_remove()
+    - net: phy: mxl-gpy: fix version reporting
+    - net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
+    - ipv6: avoid use-after-free in ip6_fragment()
+    - net: thunderbolt: fix memory leak in tbnet_open()
+    - net: mvneta: Fix an out of bounds check
+    - macsec: add missing attribute validation for offload
+    - s390/qeth: fix various format strings
+    - s390/qeth: fix use-after-free in hsci
+    - can: esd_usb: Allow REC and TEC to return to zero
+    - block: move CONFIG_BLOCK guard to top Makefile
+    - io_uring: move to separate directory
+    - io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()
+    - Linux 5.15.83
+  * 5.15.0-58.64 breaks xen bridge networking (pvh domU) (LP: #2002889) // Jammy
+    update: v5.15.83 upstream stable release (LP: #2003134)
+    - xen/netback: fix build warning
+  * Jammy update: v5.15.82 upstream stable release (LP: #2003132)
+    - arm64: mte: Avoid setting PG_mte_tagged if no tags cleared or restored
+    - drm/i915: Create a dummy object for gen6 ppgtt
+    - drm/i915/gt: Use i915_vm_put on ppgtt_create error paths
+    - erofs: fix order >= MAX_ORDER warning due to crafted negative i_size
+    - btrfs: sink iterator parameter to btrfs_ioctl_logical_to_ino
+    - btrfs: free btrfs_path before copying inodes to userspace
+    - spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock
+    - btrfs: move QUOTA_ENABLED check to rescan_should_stop from
+      btrfs_qgroup_rescan_worker
+    - btrfs: qgroup: fix sleep from invalid context bug in btrfs_qgroup_inherit()
+    - drm/display/dp_mst: Fix drm_dp_mst_add_affected_dsc_crtcs() return code
+    - drm/amdgpu: update drm_display_info correctly when the edid is read
+    - drm/amdgpu: Partially revert "drm/amdgpu: update drm_display_info correctly
+      when the edid is read"
+    - iio: health: afe4403: Fix oob read in afe4403_read_raw
+    - iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw
+    - iio: light: rpr0521: add missing Kconfig dependencies
+    - bpf, perf: Use subprog name when reporting subprog ksymbol
+    - scripts/faddr2line: Fix regression in name resolution on ppc64le
+    - ARM: at91: rm9200: fix usb device clock id
+    - libbpf: Handle size overflow for ringbuf mmap
+    - hwmon: (ltc2947) fix temperature scaling
+    - hwmon: (ina3221) Fix shunt sum critical calculation
+    - hwmon: (i5500_temp) fix missing pci_disable_device()
+    - hwmon: (ibmpex) Fix possible UAF when ibmpex_register_bmc() fails
+    - bpf: Do not copy spin lock field from user in bpf_selem_alloc
+    - nvmem: rmem: Fix return value check in rmem_read()
+    - of: property: decrement node refcount in of_fwnode_get_reference_args()
+    - ixgbevf: Fix resource leak in ixgbevf_init_module()
+    - i40e: Fix error handling in i40e_init_module()
+    - fm10k: Fix error handling in fm10k_init_module()
+    - iavf: remove redundant ret variable
+    - iavf: Fix error handling in iavf_init_module()
+    - e100: Fix possible use after free in e100_xmit_prepare
+    - net/mlx5: DR, Fix uninitialized var warning
+    - net/mlx5: Fix uninitialized variable bug in outlen_write()
+    - net/mlx5e: Fix use-after-free when reverting termination table
+    - can: sja1000_isa: sja1000_isa_probe(): add missing free_sja1000dev()
+    - can: cc770: cc770_isa_probe(): add missing free_cc770dev()
+    - can: etas_es58x: es58x_init_netdev(): free netdev when register_candev()
+    - can: m_can: pci: add missing m_can_class_free_dev() in probe/remove methods
+    - can: m_can: Add check for devm_clk_get
+    - qlcnic: fix sleep-in-atomic-context bugs caused by msleep
+    - aquantia: Do not purge addresses when setting the number of rings
+    - wifi: cfg80211: fix buffer overflow in elem comparison
+    - wifi: cfg80211: don't allow multi-BSSID in S1G
+    - wifi: mac8021: fix possible oob access in ieee80211_get_rate_duration
+    - net: phy: fix null-ptr-deref while probe() failed
+    - net: ethernet: ti: am65-cpsw: fix error handling in am65_cpsw_nuss_probe()
+    - net: net_netdev: Fix error handling in ntb_netdev_init_module()
+    - net/9p: Fix a potential socket leak in p9_socket_open
+    - net: ethernet: nixge: fix NULL dereference
+    - net: wwan: iosm: fix kernel test robot reported error
+    - net: wwan: iosm: fix dma_alloc_coherent incompatible pointer type
+    - dsa: lan9303: Correct stat name
+    - tipc: re-fetch skb cb after tipc_msg_validate
+    - net: hsr: Fix potential use-after-free
+    - net: mdiobus: fix unbalanced node reference count
+    - afs: Fix fileserver probe RTT handling
+    - net: tun: Fix use-after-free in tun_detach()
+    - packet: do not set TP_STATUS_CSUM_VALID on CHECKSUM_COMPLETE
+    - sctp: fix memory leak in sctp_stream_outq_migrate()
+    - net: ethernet: renesas: ravb: Fix promiscuous mode after system resumed
+    - hwmon: (coretemp) Check for null before removing sysfs attrs
+    - hwmon: (coretemp) fix pci device refcount leak in nv1a_ram_new()
+    - riscv: vdso: fix section overlapping under some conditions
+    - riscv: mm: Proper page permissions after initmem free
+    - ALSA: dice: fix regression for Lexicon I-ONIX FW810S
+    - error-injection: Add prompt for function error injection
+    - tools/vm/slabinfo-gnuplot: use "grep -E" instead of "egrep"
+    - nilfs2: fix NULL pointer dereference in nilfs_palloc_commit_free_entry()
+    - x86/bugs: Make sure MSR_SPEC_CTRL is updated properly upon resume from S3
+    - pinctrl: intel: Save and restore pins in "direct IRQ" mode
+    - v4l2: don't fall back to follow_pfn() if pin_user_pages_fast() fails
+    - net: stmmac: Set MAC's flow control register to reflect current settings
+    - mmc: mmc_test: Fix removal of debugfs file
+    - mmc: core: Fix ambiguous TRIM and DISCARD arg
+    - mmc: sdhci-esdhc-imx: correct CQHCI exit halt state check
+    - mmc: sdhci-sprd: Fix no reset data and command after voltage switch
+    - mmc: sdhci: Fix voltage switch delay
+    - drm/amdgpu: temporarily disable broken Clang builds due to blown stack-frame
+    - drm/amdgpu: enable Vangogh VCN indirect sram mode
+    - drm/i915: Fix negative value passed as remaining time
+    - drm/i915: Never return 0 if not all requests retired
+    - tracing/osnoise: Fix duration type
+    - tracing: Fix race where histograms can be called before the event
+    - tracing: Free buffers when a used dynamic event is removed
+    - io_uring: update res mask in io_poll_check_events
+    - io_uring: fix tw losing poll events
+    - io_uring: cmpxchg for poll arm refs release
+    - io_uring: make poll refs more robust
+    - io_uring/poll: fix poll_refs race with cancelation
+    - KVM: x86/mmu: Fix race condition in direct_page_fault
+    - ASoC: ops: Fix bounds check for _sx controls
+    - pinctrl: single: Fix potential division by zero
+    - riscv: Sync efi page table's kernel mappings before switching
+    - riscv: fix race when vmap stack overflow
+    - riscv: kexec: Fixup irq controller broken in kexec crash path
+    - nvme: fix SRCU protection of nvme_ns_head list
+    - iommu/vt-d: Fix PCI device refcount leak in has_external_pci()
+    - iommu/vt-d: Fix PCI device refcount leak in dmar_dev_scope_init()
+    - mm: __isolate_lru_page_prepare() in isolate_migratepages_block()
+    - mm: migrate: fix THP's mapcount on isolation
+    - parisc: Increase FRAME_WARN to 2048 bytes on parisc
+    - Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is
+      enabled
+    - selftests: net: add delete nexthop route warning test
+    - selftests: net: fix nexthop warning cleanup double ip typo
+    - ipv4: Handle attempt to delete multipath route when fib_info contains an nh
+      reference
+    - ipv4: Fix route deletion when nexthop info is not specified
+    - serial: stm32: Factor out GPIO RTS toggling into separate function
+    - serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode
+    - serial: stm32: Deassert Transmit Enable on ->rs485_config()
+    - i2c: npcm7xx: Fix error handling in npcm_i2c_init()
+    - i2c: imx: Only DMA messages with I2C_M_DMA_SAFE flag set
+    - ACPI: HMAT: remove unnecessary variable initialization
+    - ACPI: HMAT: Fix initiator registration for single-initiator systems
+    - Revert "clocksource/drivers/riscv: Events are stopped during CPU suspend"
+    - char: tpm: Protect tpm_pm_suspend with locks
+    - Input: raydium_ts_i2c - fix memory leak in raydium_i2c_send()
+    - ipc/sem: Fix dangling sem_array access in semtimedop race
+    - Linux 5.15.82
+  * Jammy update: v5.15.81 upstream stable release (LP: #2003130)
+    - ASoC: fsl_sai: use local device pointer
+    - ASoC: fsl_asrc fsl_esai fsl_sai: allow CONFIG_PM=N
+    - serial: Add rs485_supported to uart_port
+    - serial: fsl_lpuart: Fill in rs485_supported
+    - tty: serial: fsl_lpuart: don't break the on-going transfer when global reset
+    - sctp: remove the unnecessary sinfo_stream check in sctp_prsctp_prune_unsent
+    - sctp: clear out_curr if all frag chunks of current msg are pruned
+    - cifs: introduce new helper for cifs_reconnect()
+    - cifs: split out dfs code from cifs_reconnect()
+    - cifs: support nested dfs links over reconnect
+    - cifs: Fix connections leak when tlink setup failed
+    - ata: libata-scsi: simplify __ata_scsi_queuecmd()
+    - ata: libata-core: do not issue non-internal commands once EH is pending
+    - drm/display: Don't assume dual mode adaptors support i2c sub-addressing
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro
+    - nvme-pci: disable namespace identifiers for the MAXIO MAP1001
+    - nvme-pci: disable write zeroes on various Kingston SSD
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000
+    - iio: ms5611: Simplify IO callback parameters
+    - iio: pressure: ms5611: fixed value compensation bug
+    - ceph: do not update snapshot context when there is no new snapshot
+    - ceph: avoid putting the realm twice when decoding snaps fails
+    - x86/sgx: Create utility to validate user provided offset and length
+    - x86/sgx: Add overflow check in sgx_validate_offset_length()
+    - binder: validate alloc->mm in ->mmap() handler
+    - ceph: Use kcalloc for allocating multiple elements
+    - ceph: fix NULL pointer dereference for req->r_session
+    - wifi: mac80211: fix memory free error when registering wiphy fail
+    - wifi: mac80211_hwsim: fix debugfs attribute ps with rc table support
+    - riscv: dts: sifive unleashed: Add PWM controlled LEDs
+    - audit: fix undefined behavior in bit shift for AUDIT_BIT
+    - wifi: airo: do not assign -1 to unsigned char
+    - wifi: mac80211: Fix ack frame idr leak when mesh has no route
+    - wifi: ath11k: Fix QCN9074 firmware boot on x86
+    - spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
+    - selftests/bpf: Add verifier test for release_reference()
+    - Revert "net: macsec: report real_dev features when HW offloading is enabled"
+    - platform/x86: ideapad-laptop: Disable touchpad_switch
+    - platform/x86: touchscreen_dmi: Add info for the RCA Cambio W101 v2 2-in-1
+    - platform/x86/intel/pmt: Sapphire Rapids PMT errata fix
+    - platform/x86/intel/hid: Add some ACPI device IDs
+    - scsi: ibmvfc: Avoid path failures during live migration
+    - scsi: scsi_debug: Make the READ CAPACITY response compliant with ZBC
+    - drm: panel-orientation-quirks: Add quirk for Acer Switch V 10 (SW5-017)
+    - block, bfq: fix null pointer dereference in bfq_bio_bfqg()
+    - arm64/syscall: Include asm/ptrace.h in syscall_wrapper header.
+    - nvmet: fix memory leak in nvmet_subsys_attr_model_store_locked
+    - Revert "drm/amdgpu: Revert "drm/amdgpu: getting fan speed pwm for vega10
+      properly""
+    - ALSA: usb-audio: add quirk to fix Hamedal C20 disconnect issue
+    - RISC-V: vdso: Do not add missing symbols to version section in linker script
+    - MIPS: pic32: treat port as signed integer
+    - xfrm: fix "disable_policy" on ipv4 early demux
+    - xfrm: replay: Fix ESN wrap around for GSO
+    - af_key: Fix send_acquire race with pfkey_register
+    - ARM: dts: am335x-pcm-953: Define fixed regulators in root node
+    - ASoC: hdac_hda: fix hda pcm buffer overflow issue
+    - ASoC: sgtl5000: Reset the CHIP_CLK_CTRL reg on remove
+    - ASoC: soc-pcm: Don't zero TDM masks in __soc_pcm_open()
+    - x86/hyperv: Restore VP assist page after cpu offlining/onlining
+    - scsi: storvsc: Fix handling of srb_status and capacity change events
+    - ASoC: max98373: Add checks for devm_kcalloc
+    - regulator: core: fix kobject release warning and memory leak in
+      regulator_register()
+    - spi: dw-dma: decrease reference count in dw_spi_dma_init_mfld()
+    - regulator: core: fix UAF in destroy_regulator()
+    - bus: sunxi-rsb: Remove the shutdown callback
+    - bus: sunxi-rsb: Support atomic transfers
+    - tee: optee: fix possible memory leak in optee_register_device()
+    - ARM: dts: at91: sam9g20ek: enable udc vbus gpio pinctrl
+    - selftests: mptcp: more stable simult_flows tests
+    - selftests: mptcp: fix mibit vs mbit mix up
+    - net: liquidio: simplify if expression
+    - rxrpc: Allow list of in-use local UDP endpoints to be viewed in /proc
+    - rxrpc: Use refcount_t rather than atomic_t
+    - rxrpc: Fix race between conn bundle lookup and bundle removal [ZDI-
+      CAN-15975]
+    - net: dsa: sja1105: disallow C45 transactions on the BASE-TX MDIO bus
+    - nfc/nci: fix race with opening and closing
+    - net: pch_gbe: fix potential memleak in pch_gbe_tx_queue()
+    - 9p/fd: fix issue of list_del corruption in p9_fd_cancel()
+    - netfilter: conntrack: Fix data-races around ct mark
+    - netfilter: nf_tables: do not set up extensions for end interval
+    - iavf: Fix a crash during reset task
+    - iavf: Do not restart Tx queues after reset task failure
+    - iavf: Fix race condition between iavf_shutdown and iavf_remove
+    - ARM: mxs: fix memory leak in mxs_machine_init()
+    - ARM: dts: imx6q-prti6q: Fix ref/tcxo-clock-frequency properties
+    - net: ethernet: mtk_eth_soc: fix error handling in mtk_open()
+    - net/mlx4: Check retval of mlx4_bitmap_init
+    - net: mvpp2: fix possible invalid pointer dereference
+    - net/qla3xxx: fix potential memleak in ql3xxx_send()
+    - octeontx2-af: debugsfs: fix pci device refcount leak
+    - net: pch_gbe: fix pci device refcount leak while module exiting
+    - nfp: fill splittable of devlink_port_attrs correctly
+    - nfp: add port from netdev validation for EEPROM access
+    - macsec: Fix invalid error code set
+    - Drivers: hv: vmbus: fix double free in the error path of
+      vmbus_add_channel_work()
+    - Drivers: hv: vmbus: fix possible memory leak in vmbus_device_register()
+    - netfilter: ipset: regression in ip_set_hash_ip.c
+    - net/mlx5: Do not query pci info while pci disabled
+    - net/mlx5: Fix FW tracer timestamp calculation
+    - net/mlx5: Fix handling of entry refcount when command is not issued to FW
+    - tipc: set con sock in tipc_conn_alloc
+    - tipc: add an extra conn_get in tipc_conn_alloc
+    - tipc: check skb_linearize() return value in tipc_disc_rcv()
+    - xfrm: Fix oops in __xfrm_state_delete()
+    - xfrm: Fix ignored return value in xfrm6_init()
+    - net: wwan: iosm: use ACPI_FREE() but not kfree() in ipc_pcie_read_bios_cfg()
+    - sfc: fix potential memleak in __ef100_hard_start_xmit()
+    - net: sparx5: fix error handling in sparx5_port_open()
+    - net: sched: allow act_ct to be built without NF_NAT
+    - NFC: nci: fix memory leak in nci_rx_data_packet()
+    - regulator: twl6030: re-add TWL6032_SUBCLASS
+    - bnx2x: fix pci device refcount leak in bnx2x_vf_is_pcie_pending()
+    - dma-buf: fix racing conflict of dma_heap_add()
+    - netfilter: ipset: restore allowing 64 clashing elements in hash:net,iface
+    - netfilter: flowtable_offload: add missing locking
+    - fs: do not update freeing inode i_io_list
+    - dccp/tcp: Reset saddr on failure after inet6?_hash_connect().
+    - ipv4: Fix error return code in fib_table_insert()
+    - arcnet: fix potential memory leak in com20020_probe()
+    - s390/dasd: fix no record found for raw_track_access
+    - nfc: st-nci: fix incorrect validating logic in EVT_TRANSACTION
+    - nfc: st-nci: fix memory leaks in EVT_TRANSACTION
+    - nfc: st-nci: fix incorrect sizing calculations in EVT_TRANSACTION
+    - net: enetc: manage ENETC_F_QBV in priv->active_offloads only when enabled
+    - net: enetc: cache accesses to &priv->si->hw
+    - net: enetc: preserve TX ring priority across reconfiguration
+    - octeontx2-pf: Add check for devm_kcalloc
+    - octeontx2-af: Fix reference count issue in rvu_sdp_init()
+    - net: thunderx: Fix the ACPI memory leak
+    - s390/crashdump: fix TOD programmable field size
+    - lib/vdso: use "grep -E" instead of "egrep"
+    - [Config] updateconfigs for CC_HAS_ASM_GOTO_TIED_OUTPUT
+    - init/Kconfig: fix CC_HAS_ASM_GOTO_TIED_OUTPUT test with dash
+    - nios2: add FORCE for vmlinuz.gz
+    - mmc: sdhci-brcmstb: Re-organize flags
+    - mmc: sdhci-brcmstb: Enable Clock Gating to save power
+    - mmc: sdhci-brcmstb: Fix SDHCI_RESET_ALL for CQHCI
+    - KVM: arm64: pkvm: Fixup boot mode to reflect that the kernel resumes from
+      EL1
+    - usb: dwc3: exynos: Fix remove() function
+    - usb: cdnsp: Fix issue with Clear Feature Halt Endpoint
+    - usb: cdnsp: fix issue with ZLP - added TD_SIZE = 1
+    - ext4: fix use-after-free in ext4_ext_shift_extents
+    - arm64: dts: rockchip: lower rk3399-puma-haikou SD controller clock frequency
+    - iio: light: apds9960: fix wrong register for gesture gain
+    - iio: core: Fix entry not deleted when iio_register_sw_trigger_type() fails
+    - bus: ixp4xx: Don't touch bit 7 on IXP42x
+    - usb: dwc3: gadget: conditionally remove requests
+    - usb: dwc3: gadget: Return -ESHUTDOWN on ep disable
+    - usb: dwc3: gadget: Clear ep descriptor last
+    - nilfs2: fix nilfs_sufile_mark_dirty() not set segment usage as dirty
+    - gcov: clang: fix the buffer overflow issue
+    - mm: vmscan: fix extreme overreclaim and swap floods
+    - KVM: x86: nSVM: leave nested mode on vCPU free
+    - KVM: x86: forcibly leave nested mode on vCPU reset
+    - KVM: x86: nSVM: harden svm_free_nested against freeing vmcb02 while still in
+      use
+    - KVM: x86: add kvm_leave_nested
+    - KVM: x86: remove exit_int_info warning in svm_handle_exit
+    - x86/tsx: Add a feature bit for TSX control MSR support
+    - x86/pm: Add enumeration check before spec MSRs save/restore setup
+    - x86/ioremap: Fix page aligned size calculation in __ioremap_caller()
+    - Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode
+    - ASoC: Intel: bytcht_es8316: Add quirk for the Nanote UMPC-01
+    - tools: iio: iio_generic_buffer: Fix read size
+    - serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
+    - Input: goodix - try resetting the controller when no config is set
+    - Input: soc_button_array - add use_low_level_irq module parameter
+    - Input: soc_button_array - add Acer Switch V 10 to dmi_use_low_level_irq[]
+    - Input: i8042 - apply probe defer to more ASUS ZenBook models
+    - ASoC: stm32: dfsdm: manage cb buffers cleanup
+    - xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too
+    - xen/platform-pci: add missing free_irq() in error path
+    - platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
+    - platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)
+    - drm/amdgpu: disable BACO support on more cards
+    - zonefs: fix zone report size in __zonefs_io_error()
+    - platform/x86: hp-wmi: Ignore Smart Experience App event
+    - platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some
+      Yoga laptops
+    - [Config] updateconfigs for INET_TABLE_PERTURB_ORDER
+    - tcp: configurable source port perturb table size
+    - net: usb: qmi_wwan: add Telit 0x103a composition
+    - scsi: iscsi: Fix possible memory leak when device_register() failed
+    - gpu: host1x: Avoid trying to use GART on Tegra20
+    - dm integrity: flush the journal on suspend
+    - dm integrity: clear the journal on suspend
+    - fuse: lock inode unconditionally in fuse_fallocate()
+    - wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_OPER_CHANNEL attribute
+    - wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_CHANNEL_LIST attribute
+    - wifi: wilc1000: validate number of channels
+    - genirq/msi: Shutdown managed interrupts with unsatifiable affinities
+    - genirq: Always limit the affinity to online CPUs
+    - irqchip/gic-v3: Always trust the managed affinity provided by the core code
+    - genirq: Take the proposed affinity at face value if force==true
+    - btrfs: free btrfs_path before copying root refs to userspace
+    - btrfs: free btrfs_path before copying fspath to userspace
+    - btrfs: free btrfs_path before copying subvol info to userspace
+    - btrfs: zoned: fix missing endianness conversion in sb_write_pointer
+    - btrfs: use kvcalloc in btrfs_get_dev_zone_info
+    - btrfs: sysfs: normalize the error handling branch in btrfs_init_sysfs()
+    - drm/amd/dc/dce120: Fix audio register mapping, stop triggering KASAN
+    - drm/amd/display: No display after resume from WB/CB
+    - drm/amdgpu: Enable Aldebaran devices to report CU Occupancy
+    - drm/amdgpu: always register an MMU notifier for userptr
+    - cifs: fix missed refcounting of ipc tcon
+    - Linux 5.15.81
+  * Jammy update: v5.15.80 upstream stable release (LP: #2003122)
+    - mm: hwpoison: refactor refcount check handling
+    - mm: hwpoison: handle non-anonymous THP correctly
+    - mm: shmem: don't truncate page if memory failure happens
+    - ASoC: wm5102: Revert "ASoC: wm5102: Fix PM disable depth imbalance in
+      wm5102_probe"
+    - ASoC: wm5110: Revert "ASoC: wm5110: Fix PM disable depth imbalance in
+      wm5110_probe"
+    - ASoC: wm8997: Revert "ASoC: wm8997: Fix PM disable depth imbalance in
+      wm8997_probe"
+    - ASoC: mt6660: Keep the pm_runtime enables before component stuff in
+      mt6660_i2c_probe
+    - ASoC: rt1019: Fix the TDM settings
+    - ASoC: wm8962: Add an event handler for TEMP_HP and TEMP_SPK
+    - spi: intel: Fix the offset to get the 64K erase opcode
+    - ASoC: codecs: jz4725b: add missed Line In power control bit
+    - ASoC: codecs: jz4725b: fix reported volume for Master ctl
+    - ASoC: codecs: jz4725b: use right control for Capture Volume
+    - ASoC: codecs: jz4725b: fix capture selector naming
+    - ASoC: Intel: sof_sdw: add quirk variant for LAPBC710 NUC15
+    - selftests/futex: fix build for clang
+    - selftests/intel_pstate: fix build for ARCH=x86_64
+    - ASoC: rt1308-sdw: add the default value of some registers
+    - drm/amd/display: Remove wrong pipe control lock
+    - ACPI: scan: Add LATT2021 to acpi_ignore_dep_ids[]
+    - RDMA/efa: Add EFA 0xefa2 PCI ID
+    - btrfs: raid56: properly handle the error when unable to find the missing
+      stripe
+    - NFSv4: Retry LOCK on OLD_STATEID during delegation return
+    - ACPI: x86: Add another system to quirk list for forcing StorageD3Enable
+    - firmware: arm_scmi: Cleanup the core driver removal callback
+    - i2c: tegra: Allocate DMA memory for DMA engine
+    - i2c: i801: add lis3lv02d's I2C address for Vostro 5568
+    - drm/imx: imx-tve: Fix return type of imx_tve_connector_mode_valid
+    - btrfs: remove pointless and double ulist frees in error paths of qgroup
+      tests
+    - x86/cpu: Add several Intel server CPU model numbers
+    - ASoC: codecs: jz4725b: Fix spelling mistake "Sourc" -> "Source", "Routee" ->
+      "Route"
+    - mtd: spi-nor: intel-spi: Disable write protection only if asked
+    - spi: intel: Use correct mask for flash and protected regions
+    - KVM: x86/pmu: Do not speculatively query Intel GP PMCs that don't exist yet
+    - hugetlbfs: don't delete error page from pagecache
+    - arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8150-xperia-kumano: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8250-xperia-edo: Specify which LDO modes are allowed
+    - arm64: dts: qcom: sm8350-hdk: Specify which LDO modes are allowed
+    - spi: stm32: Print summary 'callbacks suppressed' message
+    - ARM: dts: at91: sama7g5: fix signal name of pin PB2
+    - ASoC: core: Fix use-after-free in snd_soc_exit()
+    - ASoC: tas2770: Fix set_tdm_slot in case of single slot
+    - ASoC: tas2764: Fix set_tdm_slot in case of single slot
+    - ARM: at91: pm: avoid soft resetting AC DLL
+    - serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl()
+    - serial: 8250_omap: remove wait loop from Errata i202 workaround
+    - serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()
+    - serial: 8250: omap: Flush PM QOS work on remove
+    - serial: imx: Add missing .thaw_noirq hook
+    - tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send
+    - bpf, test_run: Fix alignment problem in bpf_prog_test_run_skb()
+    - ASoC: soc-utils: Remove __exit for snd_soc_util_exit()
+    - pinctrl: rockchip: list all pins in a possible mux route for PX30
+    - scsi: scsi_transport_sas: Fix error handling in sas_phy_add()
+    - block: sed-opal: kmalloc the cmd/resp buffers
+    - bpf: Fix memory leaks in __check_func_call
+    - arm64: Fix bit-shifting UB in the MIDR_CPU_MODEL() macro
+    - siox: fix possible memory leak in siox_device_add()
+    - parport_pc: Avoid FIFO port location truncation
+    - pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
+    - drm/vc4: kms: Fix IS_ERR() vs NULL check for vc4_kms
+    - drm/panel: simple: set bpc field for logic technologies displays
+    - drm/drv: Fix potential memory leak in drm_dev_init()
+    - drm: Fix potential null-ptr-deref in drm_vblank_destroy_worker()
+    - arm64: dts: imx8mm: Fix NAND controller size-cells
+    - arm64: dts: imx8mn: Fix NAND controller size-cells
+    - ata: libata-transport: fix double ata_host_put() in ata_tport_add()
+    - ata: libata-transport: fix error handling in ata_tport_add()
+    - ata: libata-transport: fix error handling in ata_tlink_add()
+    - ata: libata-transport: fix error handling in ata_tdev_add()
+    - nfp: change eeprom length to max length enumerators
+    - MIPS: fix duplicate definitions for exported symbols
+    - MIPS: Loongson64: Add WARN_ON on kexec related kmalloc failed
+    - bpf: Initialize same number of free nodes for each pcpu_freelist
+    - net: bgmac: Drop free_netdev() from bgmac_enet_remove()
+    - mISDN: fix possible memory leak in mISDN_dsp_element_register()
+    - net: hinic: Fix error handling in hinic_module_init()
+    - net: stmmac: ensure tx function is not running in stmmac_xdp_release()
+    - soc: imx8m: Enable OCOTP clock before reading the register
+    - net: liquidio: release resources when liquidio driver open failed
+    - mISDN: fix misuse of put_device() in mISDN_register_device()
+    - net: macvlan: Use built-in RCU list checking
+    - net: caif: fix double disconnect client in chnl_net_open()
+    - bnxt_en: Remove debugfs when pci_register_driver failed
+    - net: mhi: Fix memory leak in mhi_net_dellink()
+    - net: dsa: make dsa_master_ioctl() see through port_hwtstamp_get() shims
+    - xen/pcpu: fix possible memory leak in register_pcpu()
+    - net: ionic: Fix error handling in ionic_init_module()
+    - net: ena: Fix error handling in ena_init()
+    - net: hns3: fix setting incorrect phy link ksettings for firmware in
+      resetting process
+    - bridge: switchdev: Fix memory leaks when changing VLAN protocol
+    - drbd: use after free in drbd_create_device()
+    - platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when
+      virtualized
+    - platform/surface: aggregator: Do not check for repeated unsequenced packets
+    - cifs: add check for returning value of SMB2_close_init
+    - net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in
+      ag71xx_open()
+    - net/x25: Fix skb leak in x25_lapb_receive_frame()
+    - cifs: Fix wrong return value checking when GETFLAGS
+    - net: microchip: sparx5: Fix potential null-ptr-deref in sparx_stats_init()
+      and sparx5_start()
+    - net: thunderbolt: Fix error handling in tbnet_init()
+    - cifs: add check for returning value of SMB2_set_info_init
+    - ftrace: Fix the possible incorrect kernel message
+    - ftrace: Optimize the allocation for mcount entries
+    - ftrace: Fix null pointer dereference in ftrace_add_mod()
+    - ring_buffer: Do not deactivate non-existant pages
+    - tracing: Fix memory leak in tracing_read_pipe()
+    - tracing/ring-buffer: Have polling block on watermark
+    - tracing: Fix memory leak in test_gen_synth_cmd() and
+      test_empty_synth_event()
+    - tracing: Fix wild-memory-access in register_synth_event()
+    - tracing: Fix race where eprobes can be called before the event
+    - tracing: kprobe: Fix potential null-ptr-deref on trace_event_file in
+      kprobe_event_gen_test_exit()
+    - tracing: kprobe: Fix potential null-ptr-deref on trace_array in
+      kprobe_event_gen_test_exit()
+    - drm/amd/display: Add HUBP surface flip interrupt handler
+    - ALSA: usb-audio: Drop snd_BUG_ON() from snd_usbmidi_output_open()
+    - ALSA: hda/realtek: fix speakers for Samsung Galaxy Book Pro
+    - ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
+    - Revert "usb: dwc3: disable USB core PHY management"
+    - slimbus: qcom-ngd: Fix build error when CONFIG_SLIM_QCOM_NGD_CTRL=y &&
+      CONFIG_QCOM_RPROC_COMMON=m
+    - slimbus: stream: correct presence rate frequencies
+    - speakup: fix a segfault caused by switching consoles
+    - USB: bcma: Make GPIO explicitly optional
+    - USB: serial: option: add Sierra Wireless EM9191
+    - USB: serial: option: remove old LARA-R6 PID
+    - USB: serial: option: add u-blox LARA-R6 00B modem
+    - USB: serial: option: add u-blox LARA-L6 modem
+    - USB: serial: option: add Fibocom FM160 0x0111 composition
+    - usb: add NO_LPM quirk for Realforce 87U Keyboard
+    - usb: chipidea: fix deadlock in ci_otg_del_timer
+    - usb: cdns3: host: fix endless superspeed hub port reset
+    - usb: typec: mux: Enter safe mode only when pins need to be reconfigured
+    - iio: adc: at91_adc: fix possible memory leak in at91_adc_allocate_trigger()
+    - iio: trigger: sysfs: fix possible memory leak in iio_sysfs_trig_init()
+    - iio: adc: mp2629: fix wrong comparison of channel
+    - iio: adc: mp2629: fix potential array out of bound access
+    - iio: pressure: ms5611: changed hardcoded SPI speed to value limited
+    - dm ioctl: fix misbehavior if list_versions races with module loading
+    - serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs
+    - serial: 8250: Flush DMA Rx on RLSI
+    - serial: 8250_lpss: Configure DMA also w/o DMA filter
+    - Input: iforce - invert valid length check when fetching device IDs
+    - maccess: Fix writing offset in case of fault in
+      strncpy_from_kernel_nofault()
+    - net: phy: marvell: add sleep time after enabling the loopback bit
+    - scsi: zfcp: Fix double free of FSF request when qdio send fails
+    - iommu/vt-d: Preset Access bit for IOVA in FL non-leaf paging entries
+    - iommu/vt-d: Set SRE bit only when hardware has SRS cap
+    - firmware: coreboot: Register bus in module init
+    - mmc: core: properly select voltage range without power cycle
+    - mmc: sdhci-pci-o2micro: fix card detect fail issue caused by CD# debounce
+      timeout
+    - mmc: sdhci-pci: Fix possible memory leak caused by missing pci_dev_put()
+    - docs: update mediator contact information in CoC doc
+    - misc/vmw_vmci: fix an infoleak in vmci_host_do_receive_datagram()
+    - perf/x86/intel/pt: Fix sampling using single range output
+    - nvme: restrict management ioctls to admin
+    - nvme: ensure subsystem reset is single threaded
+    - serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake
+    - perf: Improve missing SIGTRAP checking
+    - ring-buffer: Include dropped pages in counting dirty patches
+    - tracing: Fix warning on variable 'struct trace_array'
+    - net: use struct_group to copy ip/ipv6 header addresses
+    - scsi: target: tcm_loop: Fix possible name leak in tcm_loop_setup_hba_bus()
+    - scsi: scsi_debug: Fix possible UAF in sdebug_add_host_helper()
+    - kprobes: Skip clearing aggrprobe's post_handler in kprobe-on-ftrace case
+    - Input: i8042 - fix leaking of platform device on module removal
+    - macvlan: enforce a consistent minimal mtu
+    - tcp: cdg: allow tcp_cdg_release() to be called multiple times
+    - kcm: avoid potential race in kcm_tx_work
+    - kcm: close race conditions on sk_receive_queue
+    - 9p: trans_fd/p9_conn_cancel: drop client lock earlier
+    - gfs2: Check sb_bsize_shift after reading superblock
+    - gfs2: Switch from strlcpy to strscpy
+    - 9p/trans_fd: always use O_NONBLOCK read/write
+    - wifi: wext: use flex array destination for memcpy()
+    - mm: fs: initialize fsdata passed to write_begin/write_end interface
+    - net/9p: use a dedicated spinlock for trans_fd
+    - ntfs: fix use-after-free in ntfs_attr_find()
+    - ntfs: fix out-of-bounds read in ntfs_attr_find()
+    - ntfs: check overflow when iterating ATTR_RECORDs
+    - Linux 5.15.80
+  * CVE-2022-4139
+    - drm/i915: fix TLB invalidation for Gen12 video and compute engines
+  * Jammy update: v5.15.79 upstream stable release (LP: #2001570)
+    - fuse: fix readdir cache race
+    - drm/amdkfd: avoid recursive lock in migrations back to RAM
+    - drm/amdkfd: handle CPU fault on COW mapping
+    - drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()
+    - hwspinlock: qcom: correct MMIO max register for newer SoCs
+    - phy: stm32: fix an error code in probe
+    - wifi: cfg80211: silence a sparse RCU warning
+    - wifi: cfg80211: fix memory leak in query_regdb_file()
+    - soundwire: qcom: reinit broadcast completion
+    - soundwire: qcom: check for outanding writes before doing a read
+    - bpf, verifier: Fix memory leak in array reallocation for stack state
+    - bpf, sockmap: Fix the sk->sk_forward_alloc warning of sk_stream_kill_queues
+    - wifi: mac80211: Set TWT Information Frame Disabled bit as 1
+    - bpftool: Fix NULL pointer dereference when pin {PROG, MAP, LINK} without
+      FILE
+    - HID: hyperv: fix possible memory leak in mousevsc_probe()
+    - bpf, sockmap: Fix sk->sk_forward_alloc warn_on in sk_stream_kill_queues
+    - bpf: Fix sockmap calling sleepable function in teardown path
+    - bpf, sock_map: Move cancel_work_sync() out of sock lock
+    - bpf: Add helper macro bpf_for_each_reg_in_vstate
+    - bpf: Fix wrong reg type conversion in release_reference()
+    - net: gso: fix panic on frag_list with mixed head alloc types
+    - macsec: delete new rxsc when offload fails
+    - macsec: fix secy->n_rx_sc accounting
+    - macsec: fix detection of RXSCs when toggling offloading
+    - macsec: clear encryption keys from the stack after setting up offload
+    - octeontx2-pf: Use hardware register for CQE count
+    - octeontx2-pf: NIX TX overwrites SQ_CTX_HW_S[SQ_INT]
+    - net: tun: Fix memory leaks of napi_get_frags
+    - bnxt_en: Fix possible crash in bnxt_hwrm_set_coal()
+    - bnxt_en: fix potentially incorrect return value for ndo_rx_flow_steer
+    - net: fman: Unregister ethernet device on removal
+    - capabilities: fix undefined behavior in bit shift for CAP_TO_MASK
+    - phy: ralink: mt7621-pci: add sentinel to quirks table
+    - KVM: s390: pv: don't allow userspace to set the clock under PV
+    - net: lapbether: fix issue of dev reference count leakage in
+      lapbeth_device_event()
+    - hamradio: fix issue of dev reference count leakage in bpq_device_event()
+    - net: wwan: iosm: fix memory leak in ipc_wwan_dellink
+    - net: wwan: mhi: fix memory leak in mhi_mbim_dellink
+    - drm/vc4: Fix missing platform_unregister_drivers() call in
+      vc4_drm_register()
+    - tcp: prohibit TCP_REPAIR_OPTIONS if data was already sent
+    - ipv6: addrlabel: fix infoleak when sending struct ifaddrlblmsg to network
+    - can: af_can: fix NULL pointer dereference in can_rx_register()
+    - net: stmmac: dwmac-meson8b: fix meson8b_devm_clk_prepare_enable()
+    - net: broadcom: Fix BCMGENET Kconfig
+    - tipc: fix the msg->req tlv len check in
+      tipc_nl_compat_name_table_dump_header
+    - dmaengine: pxa_dma: use platform_get_irq_optional
+    - dmaengine: mv_xor_v2: Fix a resource leak in mv_xor_v2_remove()
+    - dmaengine: ti: k3-udma-glue: fix memory leak when register device fail
+    - net: lapbether: fix issue of invalid opcode in lapbeth_open()
+    - drivers: net: xgene: disable napi when register irq failed in
+      xgene_enet_open()
+    - perf stat: Fix printing os->prefix in CSV metrics output
+    - perf tools: Add the include/perf/ directory to .gitignore
+    - netfilter: nfnetlink: fix potential dead lock in nfnetlink_rcv_msg()
+    - netfilter: Cleanup nft_net->module_list from nf_tables_exit_net()
+    - net: marvell: prestera: fix memory leak in prestera_rxtx_switch_init()
+    - net: nixge: disable napi when enable interrupts failed in nixge_open()
+    - net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg
+    - net/mlx5: Bridge, verify LAG state when adding bond to bridge
+    - net/mlx5: Allow async trigger completion execution on single CPU systems
+    - net/mlx5e: E-Switch, Fix comparing termination table instance
+    - net: cpsw: disable napi in cpsw_ndo_open()
+    - net: cxgb3_main: disable napi when bind qsets failed in cxgb_up()
+    - stmmac: intel: Enable 2.5Gbps for Intel AlderLake-S
+    - stmmac: intel: Update PCH PTP clock rate from 200MHz to 204.8MHz
+    - mctp: Fix an error handling path in mctp_init()
+    - cxgb4vf: shut down the adapter when t4vf_update_port_info() failed in
+      cxgb4vf_open()
+    - stmmac: dwmac-loongson: fix missing pci_disable_msi() while module exiting
+    - stmmac: dwmac-loongson: fix missing pci_disable_device() in
+      loongson_dwmac_probe()
+    - stmmac: dwmac-loongson: fix missing of_node_put() while module exiting
+    - net: phy: mscc: macsec: clear encryption keys when freeing a flow
+    - net: atlantic: macsec: clear encryption keys from the stack
+    - ethernet: s2io: disable napi when start nic failed in s2io_card_up()
+    - net: mv643xx_eth: disable napi when init rxq or txq failed in
+      mv643xx_eth_open()
+    - ethernet: tundra: free irq when alloc ring failed in tsi108_open()
+    - net: macvlan: fix memory leaks of macvlan_common_newlink
+    - riscv: process: fix kernel info leakage
+    - riscv: vdso: fix build with llvm
+    - riscv: fix reserved memory setup
+    - arm64: efi: Fix handling of misaligned runtime regions and drop warning
+    - MIPS: jump_label: Fix compat branch range check
+    - mmc: cqhci: Provide helper for resetting both SDHCI and CQHCI
+    - mmc: sdhci-of-arasan: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci_am654: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci-tegra: Fix SDHCI_RESET_ALL for CQHCI
+    - mmc: sdhci-esdhc-imx: use the correct host caps for MMC_CAP_8_BIT_DATA
+    - ALSA: hda/hdmi - enable runtime pm for more AMD display audio
+    - ALSA: hda/ca0132: add quirk for EVGA Z390 DARK
+    - ALSA: hda: fix potential memleak in 'add_widget_node'
+    - ALSA: hda/realtek: Add Positivo C6300 model quirk
+    - ALSA: usb-audio: Yet more regression for for the delayed card registration
+    - ALSA: usb-audio: Add quirk entry for M-Audio Micro
+    - ALSA: usb-audio: Add DSD support for Accuphase DAC-60
+    - vmlinux.lds.h: Fix placement of '.data..decrypted' section
+    - ata: libata-scsi: fix SYNCHRONIZE CACHE (16) command failure
+    - nilfs2: fix deadlock in nilfs_count_free_blocks()
+    - nilfs2: fix use-after-free bug of ns_writer on remount
+    - drm/i915/dmabuf: fix sg_table handling in map_dma_buf
+    - drm/amdgpu: disable BACO on special BEIGE_GOBY card
+    - btrfs: fix match incorrectly in dev_args_match_device
+    - btrfs: selftests: fix wrong error check in btrfs_free_dummy_root()
+    - btrfs: zoned: initialize device's zone info for seeding
+    - mms: sdhci-esdhc-imx: Fix SDHCI_RESET_ALL for CQHCI
+    - udf: Fix a slab-out-of-bounds write bug in udf_find_entry()
+    - mm/damon/dbgfs: check if rm_contexts input is for a real context
+    - mm/memremap.c: map FS_DAX device memory as decrypted
+    - mm/shmem: use page_mapping() to detect page cache for uffd continue
+    - can: j1939: j1939_send_one(): fix missing CAN header initialization
+    - cert host tools: Stop complaining about deprecated OpenSSL functions
+    - dmaengine: at_hdmac: Fix at_lli struct definition
+    - dmaengine: at_hdmac: Don't start transactions at tx_submit level
+    - dmaengine: at_hdmac: Start transfer for cyclic channels in issue_pending
+    - dmaengine: at_hdmac: Fix premature completion of desc in issue_pending
+    - dmaengine: at_hdmac: Do not call the complete callback on
+      device_terminate_all
+    - dmaengine: at_hdmac: Protect atchan->status with the channel lock
+    - dmaengine: at_hdmac: Fix concurrency problems by removing atc_complete_all()
+    - dmaengine: at_hdmac: Fix concurrency over descriptor
+    - dmaengine: at_hdmac: Free the memset buf without holding the chan lock
+    - dmaengine: at_hdmac: Fix concurrency over the active list
+    - dmaengine: at_hdmac: Fix descriptor handling when issuing it to hardware
+    - dmaengine: at_hdmac: Fix completion of unissued descriptor in case of errors
+    - dmaengine: at_hdmac: Don't allow CPU to reorder channel enable
+    - dmaengine: at_hdmac: Fix impossible condition
+    - dmaengine: at_hdmac: Check return code of dma_async_device_register
+    - marvell: octeontx2: build error: unknown type name 'u64'
+    - drm/amdkfd: Migrate in CPU page fault use current mm
+    - net: tun: call napi_schedule_prep() to ensure we own a napi
+    - x86/cpu: Restore AMD's DE_CFG MSR after resume
+    - Linux 5.15.79
+  * CVE-2022-47520
+    - wifi: wilc1000: validate pairwise and authentication suite offsets
+  * CVE-2022-3545
+    - nfp: fix use-after-free in area_cache_get()
+
+  [ Ubuntu: 5.15.0-60.66 ]
+
+  * jammy/linux: 5.15.0-60.66 -proposed tracker (LP: #2003450)
+  * Revoke & rotate to new signing key (LP: #2002812)
+    - [Packaging] Revoke and rotate to new signing key
+
+ -- Masahiro Yamada <masahiro.yamada@canonical.com>  Tue, 25 Apr 2023 14:07:38 +0900
+
+linux-xilinx-zynqmp (5.15.0-1020.22) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+
+  * Miscellaneous upstream changes
+    - phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Thu, 23 Feb 2023 07:05:42 +0800
+
+linux-xilinx-zynqmp (5.15.0-1019.21) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - [Config] updateconfigs for IMA_TEMPLATE
+    - [Packaging] add python3-dev as build dependency
+    - [Packaging] add python3-dev as build dependency
+
+  * Jammy update: v5.15.61 upstream stable release (LP: #1990162)
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - [Config] updateconfigs for TRACE_IRQFLAGS_NMI_SUPPORT
+
+  * Fix iosm: WWAN cannot build the connection (DW5823e) (LP: #1998115)
+    - [Config] updateconfigs for CONFIG_IOSM
+
+  * Jammy update: v5.15.75 upstream stable release (LP: #1996825)
+    - [Config] updateconfigs for ARM64_ERRATUM_2441007
+    - [Config] updateconfigs for AS_HAS_NON_CONST_LEB128
+    - [Config] updateconfigs for MDIO_BITBANG
+
+  * Jammy update: v5.15.49 upstream stable release (LP: #1983149)
+    - [Config] updateconfigs for LIB_MEMNEQ
+
+  * Jammy update: v5.15.68 upstream stable release (LP: #1993003)
+    - [Config] updateconfigs for ARM64_BTI_KERNEL
+    - [Config] updateconfigs for ARM64_ERRATUM_2457168
+
+  * Jammy update: v5.15.65 upstream stable release (LP: #1991831)
+    - [Config] updateconfigs for ARM64_ERRATUM_2441009
+
+  * Jammy update: v5.15.76 upstream stable release (LP: #1997113)
+    - [Config] updateconfigs for ARM64_ERRATUM_1742098
+
+  * Create uc22 kernel snap
+    - Add uc22 kernel snap
+
+  * [vck190] IOMMU attach device failed message found in kernel log
+    - [Config] Disable ARM_SMMU and ARM_SMMU_V3
+
+  [ Ubuntu: 5.15.0-59.65 ]
+
+  * jammy/linux: 5.15.0-59.65 -proposed tracker (LP: #2001801)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update helper scripts
+  * CVE-2022-47940
+    - ksmbd: validate length in smb2_write()
+  * Fix iosm: WWAN cannot build the connection (DW5823e) (LP: #1998115)
+    - net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled
+    - [Config] CONFIG_IOSM update annotations on arm64 armhf ppc64el s390x
+  * support for same series backports versioning numbers (LP: #1993563)
+    - [Packaging] sameport -- add support for sameport versioning
+  * [DEP-8] Run ADT regression suite for lowlatency kernels Jammy and later
+    (LP: #1999528)
+    - [DEP-8] Fix regression suite to run on lowlatency
+  * Micron NVME storage failure [1344,5407] (LP: #1998883)
+    - nvme: add a bogus subsystem NQN quirk for Micron MTFDKBA2T0TFH
+  * Jammy update: v5.15.78 upstream stable release (LP: #1998843)
+    - scsi: lpfc: Rework MIB Rx Monitor debug info logic
+    - serial: ar933x: Deassert Transmit Enable on ->rs485_config()
+    - KVM: x86: Trace re-injected exceptions
+    - KVM: x86: Treat #DBs from the emulator as fault-like (code and DR7.GD=1)
+    - drm/amd/display: explicitly disable psr_feature_enable appropriately
+    - mm/hugetlb: fix races when looking up a CONT-PTE/PMD size hugetlb page
+    - HID: playstation: add initial DualSense Edge controller support
+    - KVM: x86: Protect the unused bits in MSR exiting flags
+    - KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
+    - KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
+    - RDMA/cma: Use output interface for net_dev check
+    - IB/hfi1: Correctly move list in sc_disable()
+    - RDMA/hns: Remove magic number
+    - RDMA/hns: Use hr_reg_xxx() instead of remaining roce_set_xxx()
+    - RDMA/hns: Disable local invalidate operation
+    - NFSv4: Fix a potential state reclaim deadlock
+    - NFSv4.1: Handle RECLAIM_COMPLETE trunking errors
+    - NFSv4.1: We must always send RECLAIM_COMPLETE after a reboot
+    - SUNRPC: Fix null-ptr-deref when xps sysfs alloc failed
+    - NFSv4.2: Fixup CLONE dest file size for zero-length count
+    - nfs4: Fix kmemleak when allocate slot failed
+    - net: dsa: Fix possible memory leaks in dsa_loop_init()
+    - RDMA/core: Fix null-ptr-deref in ib_core_cleanup()
+    - RDMA/qedr: clean up work queue on failure in qedr_alloc_resources()
+    - net: dsa: fall back to default tagger if we can't load the one from DT
+    - nfc: fdp: Fix potential memory leak in fdp_nci_send()
+    - nfc: nxp-nci: Fix potential memory leak in nxp_nci_send()
+    - nfc: s3fwrn5: Fix potential memory leak in s3fwrn5_nci_send()
+    - nfc: nfcmrvl: Fix potential memory leak in nfcmrvl_i2c_nci_send()
+    - net: fec: fix improper use of NETDEV_TX_BUSY
+    - ata: pata_legacy: fix pdc20230_set_piomode()
+    - net: sched: Fix use after free in red_enqueue()
+    - net: tun: fix bugs for oversize packet when napi frags enabled
+    - netfilter: nf_tables: netlink notifier might race to release objects
+    - netfilter: nf_tables: release flow rule object from commit path
+    - ipvs: use explicitly signed chars
+    - ipvs: fix WARNING in __ip_vs_cleanup_batch()
+    - ipvs: fix WARNING in ip_vs_app_net_cleanup()
+    - rose: Fix NULL pointer dereference in rose_send_frame()
+    - mISDN: fix possible memory leak in mISDN_register_device()
+    - isdn: mISDN: netjet: fix wrong check of device registration
+    - btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
+    - btrfs: fix inode list leak during backref walking at find_parent_nodes()
+    - btrfs: fix ulist leaks in error paths of qgroup self tests
+    - netfilter: ipset: enforce documented limit to prevent allocating huge memory
+    - Bluetooth: virtio_bt: Use skb_put to set length
+    - Bluetooth: L2CAP: fix use-after-free in l2cap_conn_del()
+    - Bluetooth: L2CAP: Fix memory leak in vhci_write
+    - net: mdio: fix undefined behavior in bit shift for __mdiobus_register
+    - ibmvnic: Free rwi on reset success
+    - stmmac: dwmac-loongson: fix invalid mdio_node
+    - net/smc: Fix possible leaked pernet namespace in smc_init()
+    - net, neigh: Fix null-ptr-deref in neigh_table_clear()
+    - ipv6: fix WARNING in ip6_route_net_exit_late()
+    - vsock: fix possible infinite sleep in vsock_connectible_wait_data()
+    - drm/msm/hdmi: Remove spurious IRQF_ONESHOT flag
+    - drm/msm/hdmi: fix IRQ lifetime
+    - video/fbdev/stifb: Implement the stifb_fillrect() function
+    - fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
+    - mtd: parsers: bcm47xxpart: print correct offset on read error
+    - mtd: parsers: bcm47xxpart: Fix halfblock reads
+    - s390/uaccess: add missing EX_TABLE entries to __clear_user()
+    - s390/cio: fix out-of-bounds access on cio_ignore free
+    - media: rkisp1: Don't pass the quantization to rkisp1_csm_config()
+    - media: rkisp1: Initialize color space on resizer sink and source pads
+    - media: rkisp1: Use correct macro for gradient registers
+    - media: rkisp1: Zero v4l2_subdev_format fields in when validating links
+    - media: s5p_cec: limit msg.len to CEC_MAX_MSG_SIZE
+    - media: cros-ec-cec: limit msg.len to CEC_MAX_MSG_SIZE
+    - media: dvb-frontends/drxk: initialize err to 0
+    - media: meson: vdec: fix possible refcount leak in vdec_probe()
+    - media: v4l: subdev: Fail graciously when getting try data for NULL state
+    - ACPI: APEI: Fix integer overflow in ghes_estatus_pool_init()
+    - scsi: core: Restrict legal sdev_state transitions via sysfs
+    - HID: saitek: add madcatz variant of MMO7 mouse device ID
+    - drm/amdgpu: set vm_update_mode=0 as default for Sienna Cichlid in SRIOV case
+    - i2c: xiic: Add platform module alias
+    - efi/tpm: Pass correct address to memblock_reserve
+    - clk: qcom: Update the force mem core bit for GPU clocks
+    - ARM: dts: imx6qdl-gw59{10,13}: fix user pushbutton GPIO offset
+    - arm64: dts: imx8: correct clock order
+    - arm64: dts: lx2160a: specify clock frequencies for the MDIO controllers
+    - arm64: dts: ls1088a: specify clock frequencies for the MDIO controllers
+    - arm64: dts: ls208xa: specify clock frequencies for the MDIO controllers
+    - block: Fix possible memory leak for rq_wb on add_disk failure
+    - firmware: arm_scmi: Suppress the driver's bind attributes
+    - firmware: arm_scmi: Make Rx chan_setup fail on memory errors
+    - firmware: arm_scmi: Fix devres allocation device in virtio transport
+    - arm64: dts: juno: Add thermal critical trip points
+    - i2c: piix4: Fix adapter not be removed in piix4_remove()
+    - Bluetooth: L2CAP: Fix attempting to access uninitialized memory
+    - block, bfq: protect 'bfqd->queued' by 'bfqd->lock'
+    - af_unix: Fix memory leaks of the whole sk due to OOB skb.
+    - fscrypt: stop using keyrings subsystem for fscrypt_master_key
+    - fscrypt: fix keyring memory leak on mount failure
+    - btrfs: fix lost file sync on direct IO write with nowait and dsync iocb
+    - btrfs: fix tree mod log mishandling of reallocated nodes
+    - btrfs: fix type of parameter generation in btrfs_get_dentry
+    - ftrace: Fix use-after-free for dynamic ftrace_ops
+    - tcp/udp: Make early_demux back namespacified.
+    - tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
+    - kprobe: reverse kp->flags when arm_kprobe failed
+    - ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()
+    - tools/nolibc/string: Fix memcmp() implementation
+    - tracing/histogram: Update document for KEYS_MAX size
+    - capabilities: fix potential memleak on error path from vfs_getxattr_alloc()
+    - fuse: add file_modified() to fallocate
+    - efi: random: reduce seed size to 32 bytes
+    - efi: random: Use 'ACPI reclaim' memory for random seed
+    - arm64: entry: avoid kprobe recursion
+    - perf/x86/intel: Fix pebs event constraints for ICL
+    - perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
+    - perf/x86/intel: Fix pebs event constraints for SPR
+    - parisc: Make 8250_gsc driver dependend on CONFIG_PARISC
+    - parisc: Export iosapic_serial_irq() symbol for serial port driver
+    - parisc: Avoid printing the hardware path twice
+    - ext4: fix warning in 'ext4_da_release_space'
+    - ext4: fix BUG_ON() when directory entry has invalid rec_len
+    - x86/syscall: Include asm/ptrace.h in syscall_wrapper header
+    - KVM: x86: Mask off reserved bits in CPUID.80000006H
+    - KVM: x86: Mask off reserved bits in CPUID.8000001AH
+    - KVM: x86: Mask off reserved bits in CPUID.80000008H
+    - KVM: x86: Mask off reserved bits in CPUID.80000001H
+    - KVM: x86: Mask off reserved bits in CPUID.8000001FH
+    - KVM: VMX: fully disable SGX if SECONDARY_EXEC_ENCLS_EXITING unavailable
+    - KVM: arm64: Fix bad dereference on MTE-enabled systems
+    - KVM: x86: emulator: em_sysexit should update ctxt->mode
+    - KVM: x86: emulator: introduce emulator_recalc_and_set_mode
+    - KVM: x86: emulator: update the emulation mode after rsm
+    - KVM: x86: emulator: update the emulation mode after CR0 write
+    - tee: Fix tee_shm_register() for kernel TEE drivers
+    - ext4,f2fs: fix readahead of verity data
+    - cifs: fix regression in very old smb1 mounts
+    - drm/rockchip: dsi: Clean up 'usage_mode' when failing to attach
+    - drm/rockchip: dsi: Force synchronous probe
+    - drm/i915/sdvo: Filter out invalid outputs more sensibly
+    - drm/i915/sdvo: Setup DDC fully before output init
+    - wifi: brcmfmac: Fix potential buffer overflow in brcmf_fweh_event_worker()
+    - Linux 5.15.78
+  * Fix AMD-PState driver for Genoa CPU (LP: #1998106)
+    - Documentation: amd-pstate: add tracer tool introduction
+    - Documentation: amd-pstate: grammar and sentence structure updates
+    - Documentation: amd-pstate: Add unit test introduction
+    - cpufreq: amd-pstate: cpufreq: amd-pstate: reset MSR_AMD_PERF_CTL register at
+      init
+    - cpufreq: amd-pstate: change amd-pstate driver to be built-in type
+    - cpufreq: amd-pstate: add amd-pstate driver parameter for mode selection
+    - Documentation: amd-pstate: add driver working mode introduction
+    - Documentation: add amd-pstate kernel command line options
+  * Mediatek WLAN RZ616(MT7922) SAR table control (LP: #1997200)
+    - mt76: mt7921: add .set_sar_specs support
+    - mt76: add 6 GHz band support in mt76_sar_freq_ranges
+    - mt76: mt7921: introduce ACPI SAR support
+    - mt76: connac: add support for limiting to maximum regulatory Tx power
+    - mt76: move sar utilities to mt76-core module
+    - mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in
+      mt7921_config
+    - mt76: mt7921: introduce ACPI SAR config in tx power
+    - wifi: mt76: mt7921: fix use after free in mt7921_acpi_read()
+  * [22.04/Jammy] Replace SAUCE AMD DP tunneling patch by upstream version
+    (LP: #1989944)
+    - Revert "UBUNTU: SAUCE: thunderbolt: Add DP out resource when DP tunnel is
+      discovered."
+    - thunderbolt: Add DP OUT resource when DP tunnel is discovered
+  * Jammy update: v5.15.77 upstream stable release (LP: #1997981)
+    - NFSv4: Fix free of uninitialized nfs4_label on referral lookup.
+    - NFSv4: Add an fattr allocation to _nfs4_discover_trunking()
+    - can: j1939: transport: j1939_session_skb_drop_old():
+      spin_unlock_irqrestore() before kfree_skb()
+    - can: kvaser_usb: Fix possible completions during init_completion
+    - ALSA: Use del_timer_sync() before freeing timer
+    - ALSA: usb-audio: Add quirks for M-Audio Fast Track C400/600
+    - ALSA: au88x0: use explicitly signed char
+    - ALSA: rme9652: use explicitly signed char
+    - USB: add RESET_RESUME quirk for NVIDIA Jetson devices in RCM
+    - usb: gadget: uvc: fix sg handling in error case
+    - usb: gadget: uvc: fix sg handling during video encode
+    - usb: dwc3: gadget: Stop processing more requests on IMI
+    - usb: dwc3: gadget: Don't set IMI for no_interrupt
+    - usb: bdc: change state when port disconnected
+    - usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96
+      controller
+    - mtd: rawnand: marvell: Use correct logic for nand-keep-config
+    - xhci: Add quirk to reset host back to default state at shutdown
+    - xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
+    - xhci: Remove device endpoints from bandwidth list when freeing the device
+    - tools: iio: iio_utils: fix digit calculation
+    - iio: light: tsl2583: Fix module unloading
+    - iio: temperature: ltc2983: allocate iio channels once
+    - iio: adxl372: Fix unsafe buffer attributes
+    - fbdev: smscufx: Fix several use-after-free bugs
+    - cpufreq: intel_pstate: Read all MSRs on the target CPU
+    - cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores
+    - fs/binfmt_elf: Fix memory leak in load_elf_binary()
+    - exec: Copy oldsighand->action under spin-lock
+    - mac802154: Fix LQI recording
+    - scsi: qla2xxx: Use transport-defined speed mask for supported_speeds
+    - drm/amdgpu: disallow gfxoff until GC IP blocks complete s2idle resume
+    - drm/msm/dsi: fix memory corruption with too many bridges
+    - drm/msm/hdmi: fix memory corruption with too many bridges
+    - drm/msm/dp: fix IRQ lifetime
+    - coresight: cti: Fix hang in cti_disable_hw()
+    - mmc: sdhci_am654: 'select', not 'depends' REGMAP_MMIO
+    - mmc: core: Fix kernel panic when remove non-standard SDIO card
+    - mmc: sdhci-pci-core: Disable ES for ASUS BIOS on Jasper Lake
+    - mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus
+    - counter: microchip-tcb-capture: Handle Signal1 read and Synapse
+    - kernfs: fix use-after-free in __kernfs_remove
+    - pinctrl: Ingenic: JZ4755 bug fixes
+    - ARC: mm: fix leakage of memory allocated for PTE
+    - perf auxtrace: Fix address filter symbol name match for modules
+    - s390/futex: add missing EX_TABLE entry to __futex_atomic_op()
+    - s390/pci: add missing EX_TABLE entries to
+      __pcistg_mio_inuser()/__pcilg_mio_inuser()
+    - Revert "scsi: lpfc: Resolve some cleanup issues following SLI path
+      refactoring"
+    - Revert "scsi: lpfc: Fix element offset in __lpfc_sli_release_iocbq_s4()"
+    - Revert "scsi: lpfc: Fix locking for lpfc_sli_iocbq_lookup()"
+    - Revert "scsi: lpfc: SLI path split: Refactor SCSI paths"
+    - Revert "scsi: lpfc: SLI path split: Refactor fast and slow paths to native
+      SLI4"
+    - Revert "scsi: lpfc: SLI path split: Refactor lpfc_iocbq"
+    - mmc: block: Remove error check of hw_reset on reset
+    - ethtool: eeprom: fix null-deref on genl_info in dump
+    - net: ieee802154: fix error return code in dgram_bind()
+    - media: v4l2: Fix v4l2_i2c_subdev_set_name function documentation
+    - media: atomisp: prevent integer overflow in sh_css_set_black_frame()
+    - drm/msm: Fix return type of mdp4_lvds_connector_mode_valid
+    - KVM: selftests: Fix number of pages for memory slot in
+      memslot_modification_stress_test
+    - ASoC: qcom: lpass-cpu: mark HDMI TX registers as volatile
+    - perf: Fix missing SIGTRAPs
+    - sched/core: Fix comparison in sched_group_cookie_match()
+    - arc: iounmap() arg is volatile
+    - mtd: rawnand: intel: Add missing of_node_put() in ebu_nand_probe()
+    - ASoC: qcom: lpass-cpu: Mark HDMI TX parity register as volatile
+    - ALSA: ac97: fix possible memory leak in snd_ac97_dev_register()
+    - perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
+    - tipc: fix a null-ptr-deref in tipc_topsrv_accept
+    - net: netsec: fix error handling in netsec_register_mdio()
+    - net: hinic: fix incorrect assignment issue in hinic_set_interrupt_cfg()
+    - net: hinic: fix memory leak when reading function table
+    - net: hinic: fix the issue of CMDQ memory leaks
+    - net: hinic: fix the issue of double release MBOX callback of VF
+    - net: macb: Specify PHY PM management done by MAC
+    - nfc: virtual_ncidev: Fix memory leak in virtual_nci_send()
+    - x86/unwind/orc: Fix unreliable stack dump with gcov
+    - amd-xgbe: fix the SFP compliance codes check for DAC cables
+    - amd-xgbe: add the bit rate quirk for Molex cables
+    - drm/i915/dp: Reset frl trained flag before restarting FRL training
+    - atlantic: fix deadlock at aq_nic_stop
+    - kcm: annotate data-races around kcm->rx_psock
+    - kcm: annotate data-races around kcm->rx_wait
+    - net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
+    - net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY
+    - tcp: minor optimization in tcp_add_backlog()
+    - tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
+    - tcp: fix indefinite deferral of RTO with SACK reneging
+    - net-memcg: avoid stalls when under memory pressure
+    - drm/amdkfd: Fix memory leak in kfd_mem_dmamap_userptr()
+    - can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error
+      path
+    - can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error
+      path
+    - PM: hibernate: Allow hybrid sleep to work with s2idle
+    - media: vivid: s_fbuf: add more sanity checks
+    - media: vivid: dev->bitmap_cap wasn't freed in all cases
+    - media: v4l2-dv-timings: add sanity checks for blanking values
+    - media: videodev2.h: V4L2_DV_BT_BLANKING_HEIGHT should check 'interlaced'
+    - media: vivid: set num_in/outputs to 0 if not supported
+    - perf vendor events power10: Fix hv-24x7 metric events
+    - ipv6: ensure sane device mtu in tunnels
+    - i40e: Fix ethtool rx-flow-hash setting for X722
+    - i40e: Fix VF hang when reset is triggered on another VF
+    - i40e: Fix flow-type by setting GL_HASH_INSET registers
+    - net: ksz884x: fix missing pci_disable_device() on error in pcidev_init()
+    - PM: domains: Fix handling of unavailable/disabled idle states
+    - perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
+    - net: fec: limit register access on i.MX6UL
+    - net: ethernet: ave: Fix MAC to be in charge of PHY PM
+    - ALSA: aoa: i2sbus: fix possible memory leak in i2sbus_add_dev()
+    - ALSA: aoa: Fix I2S device accounting
+    - openvswitch: switch from WARN to pr_warn
+    - net: ehea: fix possible memory leak in ehea_register_port()
+    - net: bcmsysport: Indicate MAC is in charge of PHY PM
+    - nh: fix scope used to find saddr when adding non gw nh
+    - net: broadcom: bcm4908enet: remove redundant variable bytes
+    - net: broadcom: bcm4908_enet: update TX stats after actual transmission
+    - netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir
+      failed
+    - net/mlx5e: Do not increment ESN when updating IPsec ESN state
+    - net/mlx5e: Extend SKB room check to include PTP-SQ
+    - net/mlx5: Fix possible use-after-free in async command interface
+    - net/mlx5: Print more info on pci error handlers
+    - net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
+    - net/mlx5: Fix crash during sync firmware reset
+    - net: do not sense pfmemalloc status in skb_append_pagefrags()
+    - kcm: do not sense pfmemalloc status in kcm_sendpage()
+    - net: enetc: survive memory pressure without crashing
+    - arm64: Add AMPERE1 to the Spectre-BHB affected list
+    - scsi: sd: Revert "scsi: sd: Remove a local variable"
+    - can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
+    - can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global
+      FIFO receive
+    - serial: core: move RS485 configuration tasks from drivers into core
+    - serial: Deassert Transmit Enable on probe in driver-specific way
+    - Linux 5.15.77
+  * RCU stalls (LP: #1991951)
+    - [Config] Harmonize RCU_CPU_STALL_TIMEOUT
+  * Jammy update: v5.15.76 upstream stable release (LP: #1997113)
+    - r8152: add PID for the Lenovo OneLink+ Dock
+    - arm64/mm: Consolidate TCR_EL1 fields
+    - usb: gadget: uvc: consistently use define for headerlen
+    - usb: gadget: uvc: use on returned header len in video_encode_isoc_sg
+    - usb: gadget: uvc: rework uvcg_queue_next_buffer to uvcg_complete_buffer
+    - usb: gadget: uvc: giveback vb2 buffer on req complete
+    - usb: gadget: uvc: improve sg exit condition
+    - [Config] updateconfigs for ARM64_ERRATUM_1742098
+    - arm64: errata: Remove AES hwcap for COMPAT tasks
+    - perf/x86/intel/pt: Relax address filter validation
+    - btrfs: enhance unsupported compat RO flags handling
+    - ocfs2: clear dinode links count in case of error
+    - ocfs2: fix BUG when iput after ocfs2_mknod fails
+    - selinux: enable use of both GFP_KERNEL and GFP_ATOMIC in convert_context()
+    - cpufreq: qcom: fix writes in read-only memory region
+    - i2c: qcom-cci: Fix ordering of pm_runtime_xx and i2c_add_adapter
+    - x86/microcode/AMD: Apply the patch early on every logical thread
+    - hwmon/coretemp: Handle large core ID value
+    - ata: ahci-imx: Fix MODULE_ALIAS
+    - x86/resctrl: Fix min_cbm_bits for AMD
+    - cpufreq: qcom: fix memory leak in error path
+    - drm/amdgpu: fix sdma doorbell init ordering on APUs
+    - mm,hugetlb: take hugetlb_lock before decrementing h->resv_huge_pages
+    - kvm: Add support for arch compat vm ioctls
+    - KVM: arm64: vgic: Fix exit condition in scan_its_table()
+    - media: ipu3-imgu: Fix NULL pointer dereference in active selection access
+    - media: mceusb: set timeout to at least timeout provided
+    - media: venus: dec: Handle the case where find_format fails
+    - x86/topology: Fix multiple packages shown on a single-package system
+    - x86/topology: Fix duplicated core ID within a package
+    - btrfs: fix processing of delayed data refs during backref walking
+    - btrfs: fix processing of delayed tree block refs during backref walking
+    - drm/vc4: Add module dependency on hdmi-codec
+    - ACPI: extlog: Handle multiple records
+    - tipc: Fix recognition of trial period
+    - tipc: fix an information leak in tipc_topsrv_kern_subscr
+    - i40e: Fix DMA mappings leak
+    - HID: magicmouse: Do not set BTN_MOUSE on double report
+    - sfc: Change VF mac via PF as first preference if available.
+    - net/atm: fix proc_mpc_write incorrect return value
+    - net: phy: dp83867: Extend RX strap quirk for SGMII mode
+    - net: phylink: add mac_managed_pm in phylink_config structure
+    - scsi: lpfc: Fix memory leak in lpfc_create_port()
+    - udp: Update reuse->has_conns under reuseport_lock.
+    - cifs: Fix xid leak in cifs_create()
+    - cifs: Fix xid leak in cifs_copy_file_range()
+    - cifs: Fix xid leak in cifs_flock()
+    - cifs: Fix xid leak in cifs_ses_add_channel()
+    - dm: remove unnecessary assignment statement in alloc_dev()
+    - net: hsr: avoid possible NULL deref in skb_clone()
+    - ionic: catch NULL pointer issue on reconfig
+    - netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
+    - nvme-hwmon: consistently ignore errors from nvme_hwmon_init
+    - nvme-hwmon: kmalloc the NVME SMART log buffer
+    - nvmet: fix workqueue MEM_RECLAIM flushing dependency
+    - net: sched: cake: fix null pointer access issue when cake_init() fails
+    - net: sched: delete duplicate cleanup of backlog and qlen
+    - net: sched: sfb: fix null pointer access issue when sfb_init() fails
+    - sfc: include vport_id in filter spec hash and equal()
+    - wwan_hwsim: fix possible memory leak in wwan_hwsim_dev_new()
+    - net: hns: fix possible memory leak in hnae_ae_register()
+    - net: sched: fix race condition in qdisc_graft()
+    - net: phy: dp83822: disable MDI crossover status change interrupt
+    - iommu/vt-d: Allow NVS regions in arch_rmrr_sanity_check()
+    - iommu/vt-d: Clean up si_domain in the init_dmars() error path
+    - fs: dlm: fix invalid derefence of sb_lvbptr
+    - arm64: mte: move register initialization to C
+    - ksmbd: handle smb2 query dir request for OutputBufferLength that is too
+      small
+    - ksmbd: fix incorrect handling of iterate_dir
+    - tracing: Simplify conditional compilation code in tracing_set_tracer()
+    - tracing: Do not free snapshot if tracer is on cmdline
+    - mmc: sdhci-tegra: Use actual clock rate for SW tuning correction
+    - perf: Skip and warn on unknown format 'configN' attrs
+    - ACPI: video: Force backlight native for more TongFang devices
+    - x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
+    - Makefile.debug: re-enable debug info for .S files
+    - mmc: core: Add SD card quirk for broken discard
+    - mm: /proc/pid/smaps_rollup: fix no vma's null-deref
+    - Linux 5.15.76
+  * UBSAN: array-index-out-of-bounds in
+    /build/linux-9H675w/linux-5.15.0/drivers/ata/libahci.c:968:41
+    (LP: #1970074) // Jammy update: v5.15.76 upstream stable release
+    (LP: #1997113)
+    - ata: ahci: Match EM_MAX_SLOTS with SATA_PMP_MAX_PORTS
+  * Jammy update: v5.15.75 upstream stable release (LP: #1996825)
+    - Revert "fs: check FMODE_LSEEK to control internal pipe splicing"
+    - ALSA: oss: Fix potential deadlock at unregistration
+    - ALSA: rawmidi: Drop register_mutex in snd_rawmidi_free()
+    - ALSA: usb-audio: Fix potential memory leaks
+    - ALSA: usb-audio: Fix NULL dererence at error path
+    - ALSA: hda/realtek: remove ALC289_FIXUP_DUAL_SPK for Dell 5530
+    - ALSA: hda/realtek: Correct pin configs for ASUS G533Z
+    - ALSA: hda/realtek: Add quirk for ASUS GV601R laptop
+    - ALSA: hda/realtek: Add Intel Reference SSID to support headset keys
+    - mtd: rawnand: atmel: Unmap streaming DMA mappings
+    - io_uring/net: don't update msg_name if not provided
+    - hv_netvsc: Fix race between VF offering and VF association message from host
+    - cifs: destage dirty pages before re-reading them for cache=none
+    - cifs: Fix the error length of VALIDATE_NEGOTIATE_INFO message
+    - iio: dac: ad5593r: Fix i2c read protocol requirements
+    - iio: ltc2497: Fix reading conversion results
+    - iio: adc: ad7923: fix channel readings for some variants
+    - iio: pressure: dps310: Refactor startup procedure
+    - iio: pressure: dps310: Reset chip after timeout
+    - xhci: dbc: Fix memory leak in xhci_alloc_dbc()
+    - usb: add quirks for Lenovo OneLink+ Dock
+    - can: kvaser_usb: Fix use of uninitialized completion
+    - can: kvaser_usb_leaf: Fix overread with an invalid command
+    - can: kvaser_usb_leaf: Fix TX queue out of sync after restart
+    - can: kvaser_usb_leaf: Fix CAN state after restart
+    - mmc: sdhci-sprd: Fix minimum clock limit
+    - i2c: designware: Fix handling of real but unexpected device interrupts
+    - fs: dlm: fix race between test_bit() and queue_work()
+    - fs: dlm: handle -EBUSY first in lock arg validation
+    - HID: multitouch: Add memory barriers
+    - quota: Check next/prev free block number after reading from quota file
+    - platform/chrome: cros_ec_proto: Update version on GET_NEXT_EVENT failure
+    - ASoC: wcd9335: fix order of Slimbus unprepare/disable
+    - ASoC: wcd934x: fix order of Slimbus unprepare/disable
+    - hwmon: (gsc-hwmon) Call of_node_get() before of_find_xxx API
+    - net: thunderbolt: Enable DMA paths only after rings are enabled
+    - regulator: qcom_rpm: Fix circular deferral regression
+    - arm64: topology: move store_cpu_topology() to shared code
+    - riscv: topology: fix default topology reporting
+    - RISC-V: Make port I/O string accessors actually work
+    - parisc: fbdev/stifb: Align graphics memory size to 4MB
+    - riscv: Make VM_WRITE imply VM_READ
+    - riscv: always honor the CONFIG_CMDLINE_FORCE when parsing dtb
+    - riscv: Pass -mno-relax only on lld < 15.0.0
+    - UM: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+    - nvmem: core: Fix memleak in nvmem_register()
+    - nvme-multipath: fix possible hang in live ns resize with ANA access
+    - nvme-pci: set min_align_mask before calculating max_hw_sectors
+    - dmaengine: mxs: use platform_driver_register
+    - drm/virtio: Check whether transferred 2D BO is shmem
+    - drm/virtio: Unlock reservations on virtio_gpu_object_shmem_init() error
+    - drm/virtio: Use appropriate atomic state in virtio_gpu_plane_cleanup_fb()
+    - drm/udl: Restore display mode on resume
+    - [Config] updateconfigs for ARM64_ERRATUM_2441007
+    - arm64: errata: Add Cortex-A55 to the repeat tlbi list
+    - mm/damon: validate if the pmd entry is present before accessing
+    - mm/mmap: undo ->mmap() when arch_validate_flags() fails
+    - xen/gntdev: Prevent leaking grants
+    - xen/gntdev: Accommodate VMA splitting
+    - PCI: Sanitise firmware BAR assignments behind a PCI-PCI bridge
+    - serial: 8250: Let drivers request full 16550A feature probing
+    - serial: 8250: Request full 16550A feature probing for OxSemi PCIe devices
+    - powercap: intel_rapl: Use standard Energy Unit for SPR Dram RAPL domain
+    - powerpc/boot: Explicitly disable usage of SPE instructions
+    - slimbus: qcom-ngd: use correct error in message of pdr_add_lookup() failure
+    - slimbus: qcom-ngd: cleanup in probe error path
+    - scsi: qedf: Populate sysfs attributes for vport
+    - gpio: rockchip: request GPIO mux to pinctrl when setting direction
+    - pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
+    - fbdev: smscufx: Fix use-after-free in ufx_ops_open()
+    - ksmbd: fix endless loop when encryption for response fails
+    - ksmbd: Fix wrong return value and message length check in smb2_ioctl()
+    - ksmbd: Fix user namespace mapping
+    - fs: record I_DIRTY_TIME even if inode already has I_DIRTY_INODE
+    - btrfs: fix race between quota enable and quota rescan ioctl
+    - btrfs: set generation before calling btrfs_clean_tree_block in
+      btrfs_init_new_buffer
+    - f2fs: complete checkpoints during remount
+    - f2fs: flush pending checkpoints when freezing super
+    - f2fs: increase the limit for reserve_root
+    - f2fs: fix to do sanity check on destination blkaddr during recovery
+    - f2fs: fix to do sanity check on summary info
+    - hardening: Avoid harmless Clang option under CONFIG_INIT_STACK_ALL_ZERO
+    - hardening: Remove Clang's enable flag for -ftrivial-auto-var-init=zero
+    - jbd2: wake up journal waiters in FIFO order, not LIFO
+    - jbd2: fix potential buffer head reference count leak
+    - jbd2: fix potential use-after-free in jbd2_fc_wait_bufs
+    - jbd2: add miss release buffer head in fc_do_one_pass()
+    - ext4: avoid crash when inline data creation follows DIO write
+    - ext4: fix null-ptr-deref in ext4_write_info
+    - ext4: make ext4_lazyinit_thread freezable
+    - ext4: fix check for block being out of directory size
+    - ext4: don't increase iversion counter for ea_inodes
+    - ext4: ext4_read_bh_lock() should submit IO if the buffer isn't uptodate
+    - ext4: place buffer head allocation before handle start
+    - ext4: fix dir corruption when ext4_dx_add_entry() fails
+    - ext4: fix miss release buffer head in ext4_fc_write_inode
+    - ext4: fix potential memory leak in ext4_fc_record_modified_inode()
+    - ext4: fix potential memory leak in ext4_fc_record_regions()
+    - ext4: update 'state->fc_regions_size' after successful memory allocation
+    - livepatch: fix race between fork and KLP transition
+    - ftrace: Properly unset FTRACE_HASH_FL_MOD
+    - ring-buffer: Allow splice to read previous partially read pages
+    - ring-buffer: Have the shortest_full queue be the shortest not longest
+    - ring-buffer: Check pending waiters when doing wake ups as well
+    - ring-buffer: Add ring_buffer_wake_waiters()
+    - ring-buffer: Fix race between reset page and reading page
+    - tracing: Disable interrupt or preemption before acquiring arch_spinlock_t
+    - tracing: Wake up ring buffer waiters on closing of the file
+    - tracing: Wake up waiters when tracing is disabled
+    - tracing: Add ioctl() to force ring buffer waiters to wake up
+    - tracing: Move duplicate code of trace_kprobe/eprobe.c into header
+    - tracing: Add "(fault)" name injection to kernel probes
+    - tracing: Fix reading strings from synthetic events
+    - thunderbolt: Explicitly enable lane adapter hotplug events at startup
+    - efi: libstub: drop pointless get_memory_map() call
+    - media: cedrus: Set the platform driver data earlier
+    - media: cedrus: Fix endless loop in cedrus_h265_skip_bits()
+    - blk-wbt: call rq_qos_add() after wb_normal is initialized
+    - KVM: x86/emulator: Fix handing of POP SS to correctly set interruptibility
+    - KVM: nVMX: Unconditionally purge queued/injected events on nested "exit"
+    - KVM: nVMX: Don't propagate vmcs12's PERF_GLOBAL_CTRL settings to vmcs02
+    - KVM: VMX: Drop bits 31:16 when shoving exception error code into VMCS
+    - staging: greybus: audio_helper: remove unused and wrong debugfs usage
+    - drm/nouveau/kms/nv140-: Disable interlacing
+    - drm/nouveau: fix a use-after-free in nouveau_gem_prime_import_sg_table()
+    - drm/i915: Fix watermark calculations for gen12+ RC CCS modifier
+    - drm/i915: Fix watermark calculations for gen12+ MC CCS modifier
+    - drm/i915: Fix watermark calculations for gen12+ CCS+CC modifier
+    - drm/amd/display: Fix vblank refcount in vrr transition
+    - smb3: must initialize two ACL struct fields to zero
+    - selinux: use "grep -E" instead of "egrep"
+    - ima: fix blocking of security.ima xattrs of unsupported algorithms
+    - userfaultfd: open userfaultfds with O_RDONLY
+    - ntfs3: rework xattr handlers and switch to POSIX ACL VFS helpers
+    - thermal: cpufreq_cooling: Check the policy first in
+      cpufreq_cooling_register()
+    - sh: machvec: Use char[] for section boundaries
+    - MIPS: SGI-IP27: Free some unused memory
+    - MIPS: SGI-IP27: Fix platform-device leak in bridge_platform_create()
+    - ARM: 9244/1: dump: Fix wrong pg_level in walk_pmd()
+    - ARM: 9247/1: mm: set readonly for MT_MEMORY_RO with ARM_LPAE
+    - objtool: Preserve special st_shndx indexes in elf_update_symbol
+    - nfsd: Fix a memory leak in an error handling path
+    - NFSD: Fix handling of oversized NFSv4 COMPOUND requests
+    - wifi: rtlwifi: 8192de: correct checking of IQK reload
+    - wifi: ath10k: add peer map clean up for peer delete in ath10k_sta_state()
+    - leds: lm3601x: Don't use mutex after it was destroyed
+    - bpf: Fix reference state management for synchronous callbacks
+    - wifi: mac80211: allow bw change during channel switch in mesh
+    - bpftool: Fix a wrong type cast in btf_dumper_int
+    - spi: mt7621: Fix an error message in mt7621_spi_probe()
+    - x86/resctrl: Fix to restore to original value when re-enabling hardware
+      prefetch register
+    - xsk: Fix backpressure mechanism on Tx
+    - bpf: Disable preemption when increasing per-cpu map_locked
+    - bpf: Propagate error from htab_lock_bucket() to userspace
+    - bpf: Use this_cpu_{inc|dec|inc_return} for bpf_task_storage_busy
+    - Bluetooth: btusb: mediatek: fix WMT failure during runtime suspend
+    - wifi: rtl8xxxu: tighten bounds checking in rtl8xxxu_read_efuse()
+    - wifi: rtw88: add missing destroy_workqueue() on error path in
+      rtw_core_init()
+    - selftests/xsk: Avoid use-after-free on ctx
+    - spi: qup: add missing clk_disable_unprepare on error in spi_qup_resume()
+    - spi: qup: add missing clk_disable_unprepare on error in
+      spi_qup_pm_resume_runtime()
+    - wifi: rtl8xxxu: Fix skb misuse in TX queue selection
+    - spi: meson-spicc: do not rely on busy flag in pow2 clk ops
+    - bpf: btf: fix truncated last_member_type_id in btf_struct_resolve
+    - wifi: rtl8xxxu: gen2: Fix mistake in path B IQ calibration
+    - wifi: rtl8xxxu: Remove copy-paste leftover in gen2_update_rate_mask
+    - wifi: mt76: sdio: fix transmitting packet hangs
+    - wifi: mt76: mt7615: add mt7615_mutex_acquire/release in
+      mt7615_sta_set_decap_offload
+    - wifi: mt76: mt7915: do not check state before configuring implicit beamform
+    - Bluetooth: RFCOMM: Fix possible deadlock on socket shutdown/release
+    - net: fs_enet: Fix wrong check in do_pd_setup
+    - bpf: Ensure correct locking around vulnerable function find_vpid()
+    - Bluetooth: hci_{ldisc,serdev}: check percpu_init_rwsem() failure
+    - netfilter: conntrack: fix the gc rescheduling delay
+    - netfilter: conntrack: revisit the gc initial rescheduling bias
+    - wifi: ath11k: fix number of VHT beamformee spatial streams
+    - x86/microcode/AMD: Track patch allocation size explicitly
+    - x86/cpu: Include the header of init_ia32_feat_ctl()'s prototype
+    - spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
+    - spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
+    - skmsg: Schedule psock work if the cached skb exists on the psock
+    - i2c: mlxbf: support lock mechanism
+    - Bluetooth: hci_core: Fix not handling link timeouts propertly
+    - xfrm: Reinject transport-mode packets through workqueue
+    - netfilter: nft_fib: Fix for rpath check with VRF devices
+    - spi: s3c64xx: Fix large transfers with DMA
+    - wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
+    - vhost/vsock: Use kvmalloc/kvfree for larger packets.
+    - eth: alx: take rtnl_lock on resume
+    - sctp: handle the error returned from sctp_auth_asoc_init_active_key
+    - tcp: fix tcp_cwnd_validate() to not forget is_cwnd_limited
+    - spi: Ensure that sg_table won't be used after being freed
+    - hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888
+      controller
+    - net: rds: don't hold sock lock when cancelling work from
+      rds_tcp_reset_callbacks()
+    - bnx2x: fix potential memory leak in bnx2x_tpa_stop()
+    - net: wwan: iosm: Call mutex_init before locking it
+    - net/ieee802154: reject zero-sized raw_sendmsg()
+    - once: add DO_ONCE_SLOW() for sleepable contexts
+    - net: mvpp2: fix mvpp2 debugfs leak
+    - drm: bridge: adv7511: fix CEC power down control register offset
+    - drm: bridge: adv7511: unregister cec i2c device after cec adapter
+    - drm/bridge: Avoid uninitialized variable warning
+    - drm/mipi-dsi: Detach devices when removing the host
+    - drm/virtio: Correct drm_gem_shmem_get_sg_table() error handling
+    - drm/bridge: parade-ps8640: Fix regulator supply order
+    - drm/dp_mst: fix drm_dp_dpcd_read return value checks
+    - drm:pl111: Add of_node_put() when breaking out of
+      for_each_available_child_of_node()
+    - ASoC: mt6359: fix tests for platform_get_irq() failure
+    - platform/chrome: fix double-free in chromeos_laptop_prepare()
+    - platform/chrome: fix memory corruption in ioctl
+    - ASoC: tas2764: Allow mono streams
+    - ASoC: tas2764: Drop conflicting set_bias_level power setting
+    - ASoC: tas2764: Fix mute/unmute
+    - platform/x86: msi-laptop: Fix old-ec check for backlight registering
+    - platform/x86: msi-laptop: Fix resource cleanup
+    - platform/chrome: cros_ec_typec: Correct alt mode index
+    - drm/amdgpu: add missing pci_disable_device() in
+      amdgpu_pmops_runtime_resume()
+    - drm/bridge: megachips: Fix a null pointer dereference bug
+    - ASoC: rsnd: Add check for rsnd_mod_power_on
+    - ALSA: hda: beep: Simplify keep-power-at-enable behavior
+    - drm/bochs: fix blanking
+    - drm/omap: dss: Fix refcount leak bugs
+    - drm/amdgpu: Fix memory leak in hpd_rx_irq_create_workqueue()
+    - mmc: au1xmmc: Fix an error handling path in au1xmmc_probe()
+    - ASoC: eureka-tlv320: Hold reference returned from of_find_xxx API
+    - drm/msm/dpu: index dpu_kms->hw_vbif using vbif_idx
+    - drm/msm/dp: correct 1.62G link rate at dp_catalog_ctrl_config_msa()
+    - drm/vmwgfx: Fix memory leak in vmw_mksstat_add_ioctl()
+    - ASoC: codecs: tx-macro: fix kcontrol put
+    - ASoC: da7219: Fix an error handling path in da7219_register_dai_clks()
+    - ALSA: dmaengine: increment buffer pointer atomically
+    - mmc: wmt-sdmmc: Fix an error handling path in wmt_mci_probe()
+    - ASoC: wm8997: Fix PM disable depth imbalance in wm8997_probe
+    - ASoC: wm5110: Fix PM disable depth imbalance in wm5110_probe
+    - ASoC: wm5102: Fix PM disable depth imbalance in wm5102_probe
+    - ASoC: mt6660: Fix PM disable depth imbalance in mt6660_i2c_probe
+    - ALSA: hda/hdmi: Don't skip notification handling during PM operation
+    - memory: pl353-smc: Fix refcount leak bug in pl353_smc_probe()
+    - memory: of: Fix refcount leak bug in of_get_ddr_timings()
+    - memory: of: Fix refcount leak bug in of_lpddr3_get_ddr_timings()
+    - locks: fix TOCTOU race when granting write lease
+    - soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
+    - soc: qcom: smem_state: Add refcounting for the 'state->of_node'
+    - ARM: dts: imx6qdl-kontron-samx6i: hook up DDC i2c bus
+    - ARM: dts: turris-omnia: Fix mpp26 pin name and comment
+    - ARM: dts: kirkwood: lsxl: fix serial line
+    - ARM: dts: kirkwood: lsxl: remove first ethernet port
+    - ia64: export memory_add_physaddr_to_nid to fix cxl build error
+    - soc/tegra: fuse: Drop Kconfig dependency on TEGRA20_APB_DMA
+    - arm64: dts: ti: k3-j7200: fix main pinmux range
+    - ARM: dts: exynos: correct s5k6a3 reset polarity on Midas family
+    - ARM: Drop CMDLINE_* dependency on ATAGS
+    - ext4: don't run ext4lazyinit for read-only filesystems
+    - arm64: ftrace: fix module PLTs with mcount
+    - ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
+    - iio: adc: at91-sama5d2_adc: fix AT91_SAMA5D2_MR_TRACKTIM_MAX
+    - iio: adc: at91-sama5d2_adc: check return status for pressure and touch
+    - iio: adc: at91-sama5d2_adc: lock around oversampling and sample freq
+    - iio: adc: at91-sama5d2_adc: disable/prepare buffer on suspend/resume
+    - iio: inkern: only release the device node when done with it
+    - iio: inkern: fix return value in devm_of_iio_channel_get_by_name()
+    - iio: ABI: Fix wrong format of differential capacitance channel ABI.
+    - iio: magnetometer: yas530: Change data type of hard_offsets to signed
+    - RDMA/mlx5: Don't compare mkey tags in DEVX indirect mkey
+    - usb: common: debug: Check non-standard control requests
+    - clk: meson: Hold reference returned by of_get_parent()
+    - clk: oxnas: Hold reference returned by of_get_parent()
+    - clk: qoriq: Hold reference returned by of_get_parent()
+    - clk: berlin: Add of_node_put() for of_get_parent()
+    - clk: sprd: Hold reference returned by of_get_parent()
+    - clk: tegra: Fix refcount leak in tegra210_clock_init
+    - clk: tegra: Fix refcount leak in tegra114_clock_init
+    - clk: tegra20: Fix refcount leak in tegra20_clock_init
+    - HSI: omap_ssi: Fix refcount leak in ssi_probe
+    - HSI: omap_ssi_port: Fix dma_map_sg error check
+    - media: exynos4-is: fimc-is: Add of_node_put() when breaking out of loop
+    - tty: xilinx_uartps: Fix the ignore_status
+    - media: meson: vdec: add missing clk_disable_unprepare on error in
+      vdec_hevc_start()
+    - media: uvcvideo: Fix memory leak in uvc_gpio_parse
+    - media: uvcvideo: Use entity get_cur in uvc_ctrl_set
+    - media: xilinx: vipp: Fix refcount leak in xvip_graph_dma_init
+    - RDMA/rxe: Fix "kernel NULL pointer dereference" error
+    - RDMA/rxe: Fix the error caused by qp->sk
+    - misc: ocxl: fix possible refcount leak in afu_ioctl()
+    - fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
+    - dmaengine: hisilicon: Disable channels when unregister hisi_dma
+    - dmaengine: hisilicon: Fix CQ head update
+    - dmaengine: hisilicon: Add multi-thread support for a DMA channel
+    - dyndbg: fix static_branch manipulation
+    - dyndbg: fix module.dyndbg handling
+    - dyndbg: let query-modname override actual module name
+    - dyndbg: drop EXPORTed dynamic_debug_exec_queries
+    - clk: qcom: sm6115: Select QCOM_GDSC
+    - mtd: devices: docg3: check the return value of devm_ioremap() in the probe
+    - phy: amlogic: phy-meson-axg-mipi-pcie-analog: Hold reference returned by
+      of_get_parent()
+    - phy: phy-mtk-tphy: fix the phy type setting issue
+    - mtd: rawnand: intel: Read the chip-select line from the correct OF node
+    - mtd: rawnand: intel: Remove undocumented compatible string
+    - mtd: rawnand: fsl_elbc: Fix none ECC mode
+    - RDMA/irdma: Align AE id codes to correct flush code and event
+    - RDMA/srp: Fix srp_abort()
+    - RDMA/siw: Always consume all skbuf data in sk_data_ready() upcall.
+    - RDMA/siw: Fix QP destroy to wait for all references dropped.
+    - ata: fix ata_id_sense_reporting_enabled() and ata_id_has_sense_reporting()
+    - ata: fix ata_id_has_devslp()
+    - ata: fix ata_id_has_ncq_autosense()
+    - ata: fix ata_id_has_dipm()
+    - mtd: rawnand: meson: fix bit map use in meson_nfc_ecc_correct()
+    - md/raid5: Ensure stripe_fill happens on non-read IO with journal
+    - md/raid5: Remove unnecessary bio_put() in raid5_read_one_chunk()
+    - RDMA/cm: Use SLID in the work completion as the DLID in responder side
+    - IB: Set IOVA/LENGTH on IB_MR in core/uverbs layers
+    - xhci: Don't show warning for reinit on known broken suspend
+    - usb: gadget: function: fix dangling pnp_string in f_printer.c
+    - drivers: serial: jsm: fix some leaks in probe
+    - serial: 8250: Toggle IER bits on only after irq has been set up
+    - tty: serial: fsl_lpuart: disable dma rx/tx use flags in lpuart_dma_shutdown
+    - phy: qualcomm: call clk_disable_unprepare in the error handling
+    - staging: vt6655: fix some erroneous memory clean-up loops
+    - slimbus: qcom-ngd-ctrl: allow compile testing without QCOM_RPROC_COMMON
+    - firmware: google: Test spinlock on panic path to avoid lockups
+    - serial: 8250: Fix restoring termios speed after suspend
+    - scsi: libsas: Fix use-after-free bug in smp_execute_task_sg()
+    - scsi: iscsi: Rename iscsi_conn_queue_work()
+    - scsi: iscsi: Add recv workqueue helpers
+    - scsi: iscsi: Run recv path from workqueue
+    - scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
+    - clk: qcom: apss-ipq6018: mark apcs_alias0_core_clk as critical
+    - clk: qcom: gcc-sm6115: Override default Alpha PLL regs
+    - RDMA/rxe: Fix resize_finish() in rxe_queue.c
+    - fsi: core: Check error number after calling ida_simple_get
+    - mfd: intel_soc_pmic: Fix an error handling path in
+      intel_soc_pmic_i2c_probe()
+    - mfd: fsl-imx25: Fix an error handling path in mx25_tsadc_setup_irq()
+    - mfd: lp8788: Fix an error handling path in lp8788_probe()
+    - mfd: lp8788: Fix an error handling path in lp8788_irq_init() and
+      lp8788_irq_init()
+    - mfd: fsl-imx25: Fix check for platform_get_irq() errors
+    - mfd: sm501: Add check for platform_driver_register()
+    - clk: mediatek: mt8183: mfgcfg: Propagate rate changes to parent
+    - dmaengine: ioat: stop mod_timer from resurrecting deleted timer in
+      __cleanup()
+    - usb: mtu3: fix failed runtime suspend in host only mode
+    - spmi: pmic-arb: correct duplicate APID to PPID mapping logic
+    - clk: vc5: Fix 5P49V6901 outputs disabling when enabling FOD
+    - clk: baikal-t1: Fix invalid xGMAC PTP clock divider
+    - clk: baikal-t1: Add shared xGMAC ref/ptp clocks internal parent
+    - clk: baikal-t1: Add SATA internal ref clock buffer
+    - clk: bcm2835: fix bcm2835_clock_rate_from_divisor declaration
+    - clk: imx: scu: fix memleak on platform_device_add() fails
+    - clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
+    - clk: ast2600: BCLK comes from EPLL
+    - mailbox: mpfs: fix handling of the reg property
+    - mailbox: mpfs: account for mbox offsets while sending
+    - mailbox: bcm-ferxrm-mailbox: Fix error check for dma_map_sg
+    - powerpc/configs: Properly enable PAPR_SCM in pseries_defconfig
+    - powerpc/math_emu/efp: Include module.h
+    - powerpc/sysdev/fsl_msi: Add missing of_node_put()
+    - powerpc/pci_dn: Add missing of_node_put()
+    - powerpc/powernv: add missing of_node_put() in opal_export_attrs()
+    - powerpc: Fix fallocate and fadvise64_64 compat parameter combination
+    - x86/hyperv: Fix 'struct hv_enlightened_vmcs' definition
+    - powerpc/64s: Fix GENERIC_CPU build flags for PPC970 / G5
+    - powerpc: Fix SPE Power ISA properties for e500v1 platforms
+    - powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
+    - powerpc/pseries/vas: Pass hw_cpu_id to node associativity HCALL
+    - crypto: sahara - don't sleep when in softirq
+    - crypto: hisilicon/zip - fix mismatch in get/set sgl_sge_nr
+    - hwrng: arm-smccc-trng - fix NO_ENTROPY handling
+    - cgroup: Honor caller's cgroup NS when resolving path
+    - hwrng: imx-rngc - Moving IRQ handler registering after
+      imx_rngc_irq_mask_clear()
+    - crypto: qat - fix default value of WDT timer
+    - crypto: hisilicon/qm - fix missing put dfx access
+    - cgroup/cpuset: Enable update_tasks_cpumask() on top_cpuset
+    - iommu/omap: Fix buffer overflow in debugfs
+    - crypto: akcipher - default implementation for setting a private key
+    - crypto: ccp - Release dma channels before dmaengine unrgister
+    - crypto: inside-secure - Change swab to swab32
+    - crypto: qat - fix DMA transfer direction
+    - cifs: return correct error in ->calc_signature()
+    - iommu/iova: Fix module config properly
+    - tracing: kprobe: Fix kprobe event gen test module on exit
+    - tracing: kprobe: Make gen test module work in arm and riscv
+    - tracing/osnoise: Fix possible recursive locking in stop_per_cpu_kthreads
+    - kbuild: remove the target in signal traps when interrupted
+    - kbuild: rpm-pkg: fix breakage when V=1 is used
+    - crypto: marvell/octeontx - prevent integer overflows
+    - crypto: cavium - prevent integer overflow loading firmware
+    - thermal/drivers/qcom/tsens-v0_1: Fix MSM8939 fourth sensor hw_id
+    - ACPI: APEI: do not add task_work to kernel thread to avoid memory leak
+    - f2fs: fix race condition on setting FI_NO_EXTENT flag
+    - f2fs: fix to account FS_CP_DATA_IO correctly
+    - selftest: tpm2: Add Client.__del__() to close /dev/tpm* handle
+    - fs: dlm: fix race in lowcomms
+    - rcu: Avoid triggering strict-GP irq-work when RCU is idle
+    - rcu: Back off upon fill_page_cache_func() allocation failure
+    - rcu-tasks: Convert RCU_LOCKDEP_WARN() to WARN_ONCE()
+    - ACPI: video: Add Toshiba Satellite/Portege Z830 quirk
+    - ACPI: tables: FPDT: Don't call acpi_os_map_memory() on invalid phys address
+    - cpufreq: intel_pstate: Add Tigerlake support in no-HWP mode
+    - MIPS: BCM47XX: Cast memcmp() of function to (void *)
+    - powercap: intel_rapl: fix UBSAN shift-out-of-bounds issue
+    - thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to
+      avoid crash
+    - ARM: decompressor: Include .data.rel.ro.local
+    - ACPI: x86: Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable
+    - x86/entry: Work around Clang __bdos() bug
+    - NFSD: Return nfserr_serverfault if splice_ok but buf->pages have data
+    - NFSD: fix use-after-free on source server when doing inter-server copy
+    - wifi: brcmfmac: fix invalid address access when enabling SCAN log level
+    - bpftool: Clear errno after libcap's checks
+    - ice: set tx_tstamps when creating new Tx rings via ethtool
+    - net: ethernet: ti: davinci_mdio: Add workaround for errata i2329
+    - openvswitch: Fix double reporting of drops in dropwatch
+    - openvswitch: Fix overreporting of drops in dropwatch
+    - tcp: annotate data-race around tcp_md5sig_pool_populated
+    - x86/mce: Retrieve poison range from hardware
+    - wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
+    - thunderbolt: Add back Intel Falcon Ridge end-to-end flow control workaround
+    - xfrm: Update ipcomp_scratches with NULL when freed
+    - iavf: Fix race between iavf_close and iavf_reset_task
+    - wifi: brcmfmac: fix use-after-free bug in brcmf_netdev_start_xmit()
+    - Bluetooth: btintel: Mark Intel controller to support LE_STATES quirk
+    - regulator: core: Prevent integer underflow
+    - wifi: mt76: mt7921: reset msta->airtime_ac while clearing up hw value
+    - Bluetooth: L2CAP: initialize delayed works at l2cap_chan_create()
+    - Bluetooth: hci_sysfs: Fix attempting to call device_add multiple times
+    - can: bcm: check the result of can_send() in bcm_can_tx()
+    - wifi: rt2x00: don't run Rt5592 IQ calibration on MT7620
+    - wifi: rt2x00: set correct TX_SW_CFG1 MAC register for MT7620
+    - wifi: rt2x00: set VGC gain for both chains of MT7620
+    - wifi: rt2x00: set SoC wmac clock register
+    - wifi: rt2x00: correctly set BBP register 86 for MT7620
+    - hwmon: (sht4x) do not overflow clamping operation on 32-bit platforms
+    - net: If sock is dead don't access sock's sk_wq in sk_stream_wait_memory
+    - Bluetooth: L2CAP: Fix user-after-free
+    - drm/nouveau/nouveau_bo: fix potential memory leak in nouveau_bo_alloc()
+    - drm: Use size_t type for len variable in drm_copy_field()
+    - drm: Prevent drm_copy_field() to attempt copying a NULL pointer
+    - drm/komeda: Fix handling of atomic commits in the atomic_commit_tail hook
+    - gpu: lontium-lt9611: Fix NULL pointer dereference in lt9611_connector_init()
+    - drm/amd/display: fix overflow on MIN_I64 definition
+    - udmabuf: Set ubuf->sg = NULL if the creation of sg table fails
+    - drm: bridge: dw_hdmi: only trigger hotplug event on link change
+    - ALSA: usb-audio: Register card at the last interface
+    - drm/vc4: vec: Fix timings for VEC modes
+    - drm: panel-orientation-quirks: Add quirk for Anbernic Win600
+    - platform/chrome: cros_ec: Notify the PM of wake events during resume
+    - platform/x86: msi-laptop: Change DMI match / alias strings to fix module
+      autoloading
+    - ASoC: SOF: pci: Change DMI match info to support all Chrome platforms
+    - drm/amdgpu: fix initial connector audio value
+    - drm/meson: reorder driver deinit sequence to fix use-after-free bug
+    - drm/meson: explicitly remove aggregate driver at module unload time
+    - mmc: sdhci-msm: add compatible string check for sdm670
+    - drm/dp: Don't rewrite link config when setting phy test pattern
+    - drm/amd/display: Remove interface for periodic interrupt 1
+    - ARM: dts: imx7d-sdb: config the max pressure for tsc2046
+    - ARM: dts: imx6q: add missing properties for sram
+    - ARM: dts: imx6dl: add missing properties for sram
+    - ARM: dts: imx6qp: add missing properties for sram
+    - ARM: dts: imx6sl: add missing properties for sram
+    - ARM: dts: imx6sll: add missing properties for sram
+    - ARM: dts: imx6sx: add missing properties for sram
+    - kselftest/arm64: Fix validatation termination record after EXTRA_CONTEXT
+    - arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply
+    - btrfs: dump extra info if one free space cache has more bitmaps than it
+      should
+    - btrfs: scrub: try to fix super block errors
+    - btrfs: don't print information about space cache or tree every remount
+    - ARM: 9242/1: kasan: Only map modules if CONFIG_KASAN_VMALLOC=n
+    - clk: zynqmp: Fix stack-out-of-bounds in strncpy`
+    - media: cx88: Fix a null-ptr-deref bug in buffer_prepare()
+    - media: platform: fix some double free in meson-ge2d and mtk-jpeg and s5p-mfc
+    - clk: zynqmp: pll: rectify rate rounding in zynqmp_pll_round_rate
+    - usb: host: xhci-plat: suspend and resume clocks
+    - usb: host: xhci-plat: suspend/resume clks for brcm
+    - dmaengine: ti: k3-udma: Reset UDMA_CHAN_RT byte counters to prevent overflow
+    - scsi: 3w-9xxx: Avoid disabling device if failing to enable it
+    - nbd: Fix hung when signal interrupts nbd_start_device_ioctl()
+    - iommu/arm-smmu-v3: Make default domain type of HiSilicon PTT device to
+      identity
+    - power: supply: adp5061: fix out-of-bounds read in adp5061_get_chg_type()
+    - staging: vt6655: fix potential memory leak
+    - blk-throttle: prevent overflow while calculating wait time
+    - ata: libahci_platform: Sanity check the DT child nodes number
+    - bcache: fix set_at_max_writeback_rate() for multiple attached devices
+    - soundwire: cadence: Don't overwrite msg->buf during write commands
+    - soundwire: intel: fix error handling on dai registration issues
+    - HID: roccat: Fix use-after-free in roccat_read()
+    - eventfd: guard wake_up in eventfd fs calls as well
+    - md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d
+    - usb: host: xhci: Fix potential memory leak in xhci_alloc_stream_info()
+    - usb: musb: Fix musb_gadget.c rxstate overflow bug
+    - arm64: dts: imx8mp: Add snps,gfladj-refclk-lpm-sel quirk to USB nodes
+    - usb: dwc3: core: Enable GUCTL1 bit 10 for fixing termination error after
+      resume bug
+    - Revert "usb: storage: Add quirk for Samsung Fit flash"
+    - staging: rtl8723bs: fix potential memory leak in rtw_init_drv_sw()
+    - staging: rtl8723bs: fix a potential memory leak in rtw_init_cmd_priv()
+    - scsi: tracing: Fix compile error in trace_array calls when TRACING is
+      disabled
+    - ext2: Use kvmalloc() for group descriptor array
+    - nvme: copy firmware_rev on each init
+    - nvmet-tcp: add bounds check on Transfer Tag
+    - usb: idmouse: fix an uninit-value in idmouse_open
+    - clk: bcm2835: Make peripheral PLLC critical
+    - clk: bcm2835: Round UART input clock up
+    - perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
+    - io_uring: correct pinned_vm accounting
+    - io_uring/rw: fix short rw error handling
+    - io_uring/rw: fix error'ed retry return values
+    - io_uring/rw: fix unexpected link breakage
+    - mm: hugetlb: fix UAF in hugetlb_handle_userfault
+    - net: ieee802154: return -EINVAL for unknown addr type
+    - ALSA: usb-audio: Fix last interface check for registration
+    - blk-wbt: fix that 'rwb->wc' is always set to 1 in wbt_init()
+    - [Config] updateconfigs for MDIO_BITBANG
+    - net: ethernet: ti: davinci_mdio: fix build for mdio bitbang uses
+    - Revert "net/ieee802154: reject zero-sized raw_sendmsg()"
+    - net/ieee802154: don't warn zero-sized raw_sendmsg()
+    - drm/amd/display: Fix build breakage with CONFIG_DEBUG_FS=n
+    - Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
+    - Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
+    - lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
+    - [Config] updateconfigs for AS_HAS_NON_CONST_LEB128
+    - ext4: continue to expand file system when the target size doesn't reach
+    - thermal: intel_powerclamp: Use first online CPU as control_cpu
+    - gcov: support GCC 12.1 and newer compilers
+    - io-wq: Fix memory leak in worker creation
+    - Linux 5.15.75
+  * [SRU] Ubuntu 22.04 - NVMe TCP - Host fails to reconnect to target after
+    link down/link up sequence (LP: #1989990)
+    - nvme-fabrics: parse nvme connect Linux error codes
+    - nvme-tcp: handle number of queue changes
+    - nvme-rdma: handle number of queue changes
+    - nvmet: expose max queues to configfs
+
+  [ Ubuntu: 5.15.0-58.64 ]
+
+  * jammy/linux: 5.15.0-58.64 -proposed tracker (LP: #2001670)
+  * CVE-2022-3643
+    - xen/netback: Ensure protocol headers don't fall in the non-linear area
+  * CVE-2022-4378
+    - proc: proc_skip_spaces() shouldn't think it is working on C strings
+    - proc: avoid integer type confusion in get_proc_long
+  * CVE-2022-45934
+    - Bluetooth: L2CAP: Fix u8 overflow
+  * CVE-2022-42896
+    - Bluetooth: L2CAP: Fix accepting connection request for invalid SPSM
+    - Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm
+
+  [ Ubuntu: 5.15.0-57.63 ]
+
+  * jammy/linux: 5.15.0-57.63 -proposed tracker (LP: #1997737)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2022.11.14)
+  * Expose built-in trusted and revoked certificates (LP: #1996892)
+    - [Packaging] Expose built-in trusted and revoked certificates
+  * TEE Support for CCP driver (LP: #1991608)
+    - crypto: ccp: Add support for TEE for PCI ID 0x14CA
+  * alsa: soc: the kernel print UBSAN calltrace on the machine with cs35l41
+    codec (LP: #1996121)
+    - ASoC: cs35l41: Add one more variable in the debug log
+    - ASoC: cs35l41: Fix an out-of-bounds access in otp_packed_element_t
+  * Fix ath11k deadlock on WCN6855 (LP: #1995041)
+    - wifi: ath11k: avoid deadlock during regulatory update in
+      ath11k_regd_update()
+  * [UBUNTU 20.04] boot: Add s390x secure boot trailer (LP: #1996071)
+    - s390/boot: add secure boot trailer
+  * Fix rfkill causing soft blocked wifi (LP: #1996198)
+    - platform/x86: hp_wmi: Fix rfkill causing soft blocked wifi
+  * Fix Thunderbolt device hotplug fail when connect via thunderbolt dock
+    (LP: #1991366)
+    - PCI: Fix used_buses calculation in pci_scan_child_bus_extend()
+    - PCI: Pass available buses even if the bridge is already configured
+    - PCI: Move pci_assign_unassigned_root_bus_resources()
+    - PCI: Distribute available resources for root buses, too
+    - PCI: Fix whitespace and indentation
+    - PCI: Fix typo in pci_scan_child_bus_extend()
+  * md: Replace snprintf with scnprintf (LP: #1993315)
+    - md: Replace snprintf with scnprintf
+  * input/keyboard: the keyboard on some Asus laptops can't work (LP: #1992266)
+    - ACPI: resource: Skip IRQ override on Asus Vivobook K3402ZA/K3502ZA
+    - ACPI: resource: Add ASUS model S5402ZA to quirks
+  * Fix Turbostat is not working for fam: 6 model: 191: stepping: 2 CPU
+    (LP: #1991365)
+    - tools/power turbostat: Add support for RPL-S
+  * pcieport 0000:00:1b.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal),
+    type=Transaction Layer, (Requester ID) (LP: #1988797)
+    - PCI/PTM: Cache PTM Capability offset
+    - PCI/PTM: Add pci_upstream_ptm() helper
+    - PCI/PTM: Separate configuration and enable
+    - PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
+    - PCI/PTM: Move pci_ptm_info() body into its only caller
+    - PCI/PTM: Preserve RsvdP bits in PTM Control register
+    - PCI/PTM: Reorder functions in logical order
+    - PCI/PTM: Consolidate PTM interface declarations
+    - PCI/PM: Always disable PTM for all devices during suspend
+    - PCI/PM: Simplify pci_pm_suspend_noirq()
+  * Fix RPL-S support on powercap/intel_rapl (LP: #1990161)
+    - x86/cpu: Drop spurious underscore from RAPTOR_LAKE #define
+    - x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
+    - x86/cpu: Add new Raptor Lake CPU model number
+    - powercap: intel_rapl: add support for RaptorLake
+    - powercap: intel_rapl: Add support for RAPTORLAKE_P
+    - powercap: intel_rapl: Add support for RAPTORLAKE_S
+  * AMD Yellow Carp system hang on HDMI plug in/out over HP hook2 docking
+    (LP: #1991974)
+    - drm/amd/display: Fix for link encoder access for MST.
+    - drm/amd/display: Fix MST link encoder availability check.
+    - drm/amd/display: FEC configuration for dpia links
+    - drm/amd/display: FEC configuration for dpia links in MST mode
+    - drm/amd/display: Add work around for tunneled MST.
+  * Jammy update: v5.15.74 upstream stable release (LP: #1995638)
+    - nilfs2: fix use-after-free bug of struct nilfs_root
+    - nilfs2: fix leak of nilfs_root in case of writer thread creation failure
+    - nilfs2: replace WARN_ONs by nilfs_error for checkpoint acquisition failure
+    - ceph: don't truncate file in atomic_open
+    - random: restore O_NONBLOCK support
+    - random: clamp credited irq bits to maximum mixed
+    - ALSA: hda: Fix position reporting on Poulsbo
+    - efi: Correct Macmini DMI match in uefi cert quirk
+    - USB: serial: qcserial: add new usb-id for Dell branded EM7455
+    - Revert "powerpc/rtas: Implement reentrant rtas call"
+    - Revert "crypto: qat - reduce size of mapped region"
+    - random: avoid reading two cache lines on irq randomness
+    - random: use expired timer rather than wq for mixing fast pool
+    - Input: xpad - add supported devices as contributed on github
+    - Input: xpad - fix wireless 360 controller breaking after suspend
+    - misc: pci_endpoint_test: Aggregate params checking for xfer
+    - misc: pci_endpoint_test: Fix pci_endpoint_test_{copy,write,read}() panic
+    - Linux 5.15.74
+  * Jammy update: v5.15.73 upstream stable release (LP: #1995637)
+    - Makefile.extrawarn: Move -Wcast-function-type-strict to W=1
+    - docs: update mediator information in CoC docs
+    - xsk: Inherit need_wakeup flag for shared sockets
+    - mm: gup: fix the fast GUP race against THP collapse
+    - powerpc/64s/radix: don't need to broadcast IPI for radix pmd collapse flush
+    - firmware: arm_scmi: Improve checks in the info_get operations
+    - firmware: arm_scmi: Harden accesses to the sensor domains
+    - firmware: arm_scmi: Add SCMI PM driver remove routine
+    - dmaengine: xilinx_dma: Fix devm_platform_ioremap_resource error handling
+    - dmaengine: xilinx_dma: cleanup for fetching xlnx,num-fstores property
+    - dmaengine: xilinx_dma: Report error in case of dma_set_mask_and_coherent API
+      failure
+    - ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
+    - scsi: qedf: Fix a UAF bug in __qedf_probe()
+    - net/ieee802154: fix uninit value bug in dgram_sendmsg
+    - net: marvell: prestera: add support for for Aldrin2
+    - ALSA: hda/hdmi: Fix the converter reuse for the silent stream
+    - um: Cleanup syscall_handler_t cast in syscalls_32.h
+    - um: Cleanup compiler warning in arch/x86/um/tls_32.c
+    - arch: um: Mark the stack non-executable to fix a binutils warning
+    - net: atlantic: fix potential memory leak in aq_ndev_close()
+    - drm/amd/display: Fix double cursor on non-video RGB MPO
+    - drm/amd/display: Assume an LTTPR is always present on fixed_vs links
+    - drm/amd/display: update gamut remap if plane has changed
+    - drm/amd/display: skip audio setup when audio stream is enabled
+    - mmc: core: Replace with already defined values for readability
+    - mmc: core: Terminate infinite loop in SD-UHS voltage switch
+    - perf parse-events: Identify broken modifiers
+    - mm/huge_memory: minor cleanup for split_huge_pages_all
+    - mm/huge_memory: use pfn_to_online_page() in split_huge_pages_all()
+    - wifi: cfg80211: fix MCS divisor value
+    - net/mlx5: Disable irq when locking lag_lock
+    - usb: mon: make mmapped memory read only
+    - USB: serial: ftdi_sio: fix 300 bps rate for SIO
+    - rpmsg: qcom: glink: replace strncpy() with strscpy_pad()
+    - Revert "clk: ti: Stop using legacy clkctrl names for omap4 and 5"
+    - Linux 5.15.73
+  * Jammy update: v5.15.72 upstream stable release (LP: #1995517)
+    - ALSA: hda: Do disconnect jacks at codec unbind
+    - ALSA: hda: Fix hang at HD-audio codec unbinding due to refcount saturation
+    - ALSA: hda: Fix Nvidia dp infoframe
+    - cgroup: reduce dependency on cgroup_mutex
+    - cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
+    - uas: add no-uas quirk for Hiksemi usb_disk
+    - usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS
+    - uas: ignore UAS for Thinkplus chips
+    - usb: typec: ucsi: Remove incorrect warning
+    - thunderbolt: Explicitly reset plug events delay back to USB4 spec value
+    - net: usb: qmi_wwan: Add new usb-id for Dell branded EM7455
+    - Input: snvs_pwrkey - fix SNVS_HPVIDR1 register address
+    - can: c_can: don't cache TX messages for C_CAN cores
+    - clk: ingenic-tcu: Properly enable registers before accessing timers
+    - x86/sgx: Do not fail on incomplete sanitization on premature stop of ksgxd
+    - ARM: dts: integrator: Tag PCI host with device_type
+    - ntfs: fix BUG_ON in ntfs_lookup_inode_by_name()
+    - mm/damon/dbgfs: fix memory leak when using debugfs_lookup()
+    - net: mt7531: only do PLL once after the reset
+    - Revert "firmware: arm_scmi: Add clock management to the SCMI power domain"
+    - drm/i915/gt: Restrict forced preemption to the active context
+    - drm/amdgpu: Add amdgpu suspend-resume code path under SRIOV
+    - vduse: prevent uninitialized memory accesses
+    - libata: add ATA_HORKAGE_NOLPM for Pioneer BDR-207M and BDR-205
+    - mmc: moxart: fix 4-bit bus width and remove 8-bit bus width
+    - mmc: hsq: Fix data stomping during mmc recovery
+    - mm/page_alloc: fix race condition between build_all_zonelists and page
+      allocation
+    - mm: prevent page_frag_alloc() from corrupting the memory
+    - mm: fix dereferencing possible ERR_PTR
+    - mm/migrate_device.c: flush TLB while holding PTL
+    - mm: fix madivse_pageout mishandling on non-LRU page
+    - mm,hwpoison: check mm when killing accessing process
+    - media: dvb_vb2: fix possible out of bound access
+    - media: rkvdec: Disable H.264 error detection
+    - media: v4l2-compat-ioctl32.c: zero buffer passed to
+      v4l2_compat_get_array_args()
+    - swiotlb: max mapping size takes min align mask into account
+    - ARM: dts: am33xx: Fix MMCHS0 dma properties
+    - reset: imx7: Fix the iMX8MP PCIe PHY PERST support
+    - ARM: dts: am5748: keep usb4_tm disabled
+    - soc: sunxi: sram: Actually claim SRAM regions
+    - soc: sunxi: sram: Prevent the driver from being unbound
+    - soc: sunxi_sram: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - soc: sunxi: sram: Fix probe function ordering issues
+    - soc: sunxi: sram: Fix debugfs info for A64 SRAM C
+    - ASoC: imx-card: Fix refcount issue with of_node_put
+    - arm64: dts: qcom: sm8350: fix UFS PHY serdes size
+    - ASoC: tas2770: Reinit regcache on reset
+    - drm/bridge: lt8912b: add vsync hsync
+    - drm/bridge: lt8912b: set hdmi or dvi mode
+    - drm/bridge: lt8912b: fix corrupted image output
+    - Revert "drm: bridge: analogix/dp: add panel prepare/unprepare in
+      suspend/resume time"
+    - Input: melfas_mip4 - fix return value check in mip4_probe()
+    - gpio: mvebu: Fix check for pwm support on non-A8K platforms
+    - usbnet: Fix memory leak in usbnet_disconnect()
+    - net: sched: act_ct: fix possible refcount leak in tcf_ct_init()
+    - cxgb4: fix missing unlock on ETHOFLD desc collect fail path
+    - net/mlxbf_gige: Fix an IS_ERR() vs NULL bug in mlxbf_gige_mdio_probe
+    - nvme: Fix IOC_PR_CLEAR and IOC_PR_RELEASE ioctls for nvme devices
+    - wifi: mac80211: fix regression with non-QoS drivers
+    - net: stmmac: power up/down serdes in stmmac_open/release
+    - net: phy: Don't WARN for PHY_UP state in mdio_bus_phy_resume()
+    - selftests: Fix the if conditions of in test_extra_filter()
+    - vdpa/ifcvf: fix the calculation of queuepair
+    - fs: split off setxattr_copy and do_setxattr function from setxattr
+    - clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks
+    - clk: iproc: Do not rely on node name for correct PLL setup
+    - KVM: x86: Hide IA32_PLATFORM_DCA_CAP[31:0] from the guest
+    - x86/alternative: Fix race in try_get_desc()
+    - drm/i915/gem: Really move i915_gem_context.link under ref protection
+    - Linux 5.15.72
+  * Jammy update: v5.15.71 upstream stable release (LP: #1995420)
+    - drm/amdgpu: Separate vf2pf work item init from virt data exchange
+    - drm/amdgpu: make sure to init common IP before gmc
+    - staging: r8188eu: Remove support for devices with 8188FU chipset (0bda:f179)
+    - staging: r8188eu: Add Rosewill USB-N150 Nano to device tables
+    - usb: dwc3: gadget: Avoid starting DWC3 gadget during UDC unbind
+    - usb: dwc3: Issue core soft reset before enabling run/stop
+    - usb: dwc3: gadget: Prevent repeat pullup()
+    - usb: dwc3: gadget: Refactor pullup()
+    - usb: dwc3: gadget: Don't modify GEVNTCOUNT in pullup()
+    - usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop
+    - usb: add quirks for Lenovo OneLink+ Dock
+    - usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
+    - Revert "usb: add quirks for Lenovo OneLink+ Dock"
+    - Revert "usb: gadget: udc-xilinx: replace memcpy with memcpy_toio"
+    - drivers/base: Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES
+    - USB: core: Fix RST error in hub.c
+    - USB: serial: option: add Quectel BG95 0x0203 composition
+    - USB: serial: option: add Quectel RM520N
+    - ALSA: core: Fix double-free at snd_card_new()
+    - ALSA: hda/tegra: set depop delay for tegra
+    - ALSA: hda: add Intel 5 Series / 3400 PCI DID
+    - ALSA: hda/realtek: Add quirk for Huawei WRT-WX9
+    - ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5570 laptop
+    - ALSA: hda/realtek: Re-arrange quirk table entries
+    - ALSA: hda/realtek: Add pincfg for ASUS G513 HP jack
+    - ALSA: hda/realtek: Add pincfg for ASUS G533Z HP jack
+    - ALSA: hda/realtek: Add quirk for ASUS GA503R laptop
+    - ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5530 laptop
+    - iommu/vt-d: Check correct capability for sagaw determination
+    - btrfs: fix hang during unmount when stopping block group reclaim worker
+    - btrfs: fix hang during unmount when stopping a space reclaim worker
+    - media: flexcop-usb: fix endpoint type check
+    - usb: dwc3: core: leave default DMA if the controller does not support 64-bit
+      DMA
+    - efi: x86: Wipe setup_data on pure EFI boot
+    - efi: libstub: check Shim mode using MokSBStateRT
+    - wifi: mt76: fix reading current per-tid starting sequence number for
+      aggregation
+    - gpio: mockup: fix NULL pointer dereference when removing debugfs
+    - gpio: mockup: Fix potential resource leakage when register a chip
+    - gpiolib: cdev: Set lineevent_state::irq after IRQ register successfully
+    - riscv: fix a nasty sigreturn bug...
+    - kasan: call kasan_malloc() from __kmalloc_*track_caller()
+    - can: flexcan: flexcan_mailbox_read() fix return value for drop = true
+    - net: mana: Add rmb after checking owner bits
+    - mm/slub: fix to return errno if kmalloc() fails
+    - mm: slub: fix flush_cpu_slab()/__free_slab() invocations in task context.
+    - KVM: x86: Inject #UD on emulated XSETBV if XSAVES isn't enabled
+    - arm64: topology: fix possible overflow in amu_fie_setup()
+    - vmlinux.lds.h: CFI: Reduce alignment of jump-table to function alignment
+    - xfs: reorder iunlink remove operation in xfs_ifree
+    - xfs: fix xfs_ifree() error handling to not leak perag ref
+    - xfs: validate inode fork size against fork format
+    - firmware: arm_scmi: Harden accesses to the reset domains
+    - firmware: arm_scmi: Fix the asynchronous reset requests
+    - arm64: dts: rockchip: Pull up wlan wake# on Gru-Bob
+    - arm64: dts: rockchip: Fix typo in lisense text for PX30.Core
+    - drm/mediatek: dsi: Add atomic {destroy,duplicate}_state, reset callbacks
+    - arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
+    - dmaengine: ti: k3-udma-private: Fix refcount leak bug in of_xudma_dev_get()
+    - arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
+    - netfilter: nf_conntrack_sip: fix ct_sip_walk_headers
+    - netfilter: nf_conntrack_irc: Tighten matching on DCC message
+    - netfilter: nfnetlink_osf: fix possible bogus match in nf_osf_find()
+    - ice: Don't double unplug aux on peer initiated reset
+    - iavf: Fix cached head and tail value for iavf_get_tx_pending
+    - ipvlan: Fix out-of-bound bugs caused by unset skb->mac_header
+    - net: core: fix flow symmetric hash
+    - net: phy: aquantia: wait for the suspend/resume operations to finish
+    - scsi: qla2xxx: Fix memory leak in __qlt_24xx_handle_abts()
+    - scsi: mpt3sas: Fix return value check of dma_get_required_mask()
+    - net: bonding: Share lacpdu_mcast_addr definition
+    - net: bonding: Unsync device addresses on ndo_stop
+    - net: team: Unsync device addresses on ndo_stop
+    - drm/panel: simple: Fix innolux_g121i1_l01 bus_format
+    - MIPS: lantiq: export clk_get_io() for lantiq_wdt.ko
+    - MIPS: Loongson32: Fix PHY-mode being left unspecified
+    - um: fix default console kernel parameter
+    - iavf: Fix bad page state
+    - mlxbf_gige: clear MDIO gateway lock after read
+    - i40e: Fix set max_tx_rate when it is lower than 1 Mbps
+    - sfc: fix TX channel offset when using legacy interrupts
+    - sfc: fix null pointer dereference in efx_hard_start_xmit
+    - drm/hisilicon/hibmc: Allow to be built if COMPILE_TEST is enabled
+    - drm/hisilicon: Add depends on MMU
+    - of: mdio: Add of_node_put() when breaking out of for_each_xx
+    - net: ipa: properly limit modem routing table use
+    - wireguard: ratelimiter: disable timings test by default
+    - wireguard: netlink: avoid variable-sized memcpy on sockaddr
+    - net: enetc: move enetc_set_psfp() out of the common enetc_set_features()
+    - net: enetc: deny offload of tc-based TSN features on VF interfaces
+    - net/sched: taprio: avoid disabling offload when it was never enabled
+    - net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo child
+      qdiscs
+    - netfilter: nf_tables: fix nft_counters_enabled underflow at
+      nf_tables_addchain()
+    - netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
+    - netfilter: ebtables: fix memory leak when blob is malformed
+    - net: ravb: Fix PHY state warning splat during system resume
+    - net: sh_eth: Fix PHY state warning splat during system resume
+    - can: gs_usb: gs_can_open(): fix race dev->can.state condition
+    - perf stat: Fix BPF program section name
+    - perf jit: Include program header in ELF files
+    - perf kcore_copy: Do not check /proc/modules is unchanged
+    - perf tools: Honor namespace when synthesizing build-ids
+    - drm/mediatek: dsi: Move mtk_dsi_stop() call back to mtk_dsi_poweroff()
+    - net/smc: Stop the CLC flow if no link to map buffers on
+    - bonding: fix NULL deref in bond_rr_gen_slave_id
+    - net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD
+    - net: sched: fix possible refcount leak in tc_new_tfilter()
+    - bnxt: prevent skb UAF after handing over to PTP worker
+    - selftests: forwarding: add shebang for sch_red.sh
+    - KVM: x86/mmu: Fold rmap_recycle into rmap_add
+    - serial: fsl_lpuart: Reset prior to registration
+    - serial: Create uart_xmit_advance()
+    - serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
+    - serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
+    - s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup
+    - drm/amd/amdgpu: fixing read wrong pf2vf data in SRIOV
+    - Drivers: hv: Never allocate anything besides framebuffer from framebuffer
+      memory region
+    - drm/gma500: Fix BUG: sleeping function called from invalid context errors
+    - drm/amd/pm: disable BACO entry/exit completely on several sienna cichlid
+      cards
+    - drm/amdgpu: use dirty framebuffer helper
+    - drm/amd/display: Limit user regamma to a valid value
+    - drm/amd/display: Reduce number of arguments of dml31's
+      CalculateWatermarksAndDRAMSpeedChangeSupport()
+    - drm/amd/display: Reduce number of arguments of dml31's
+      CalculateFlipSchedule()
+    - drm/amd/display: Mark dml30's UseMinimumDCFCLK() as noinline for stack usage
+    - drm/rockchip: Fix return type of cdn_dp_connector_mode_valid
+    - fsdax: Fix infinite loop in dax_iomap_rw()
+    - workqueue: don't skip lockdep work dependency in cancel_work_sync()
+    - i2c: imx: If pm_runtime_get_sync() returned 1 device access is possible
+    - i2c: mlxbf: incorrect base address passed during io write
+    - i2c: mlxbf: prevent stack overflow in mlxbf_i2c_smbus_start_transaction()
+    - i2c: mlxbf: Fix frequency calculation
+    - drm/amdgpu: don't register a dirty callback for non-atomic
+    - NFSv4: Fixes for nfs4_inode_return_delegation()
+    - devdax: Fix soft-reservation memory description
+    - ext4: make directory inode spreading reflect flexbg size
+    - ext4: fix bug in extents parsing when eh_entries == 0 and eh_depth > 0
+    - ext4: limit the number of retries after discarding preallocations blocks
+    - ext4: make mballoc try target group first even with mb_optimize_scan
+    - ext4: avoid unnecessary spreading of allocations among groups
+    - ext4: use locality group preallocation for small closed files
+    - Linux 5.15.71
+    - Revert "drm/amdgpu: use dirty framebuffer helper"
+  * Jammy update: v5.15.70 upstream stable release (LP: #1995415)
+    - drm/tegra: vic: Fix build warning when CONFIG_PM=n
+    - serial: atmel: remove redundant assignment in rs485_config
+    - tty: serial: atmel: Preserve previous USART mode if RS485 disabled
+    - of: fdt: fix off-by-one error in unflatten_dt_nodes()
+    - pinctrl: qcom: sc8180x: Fix gpio_wakeirq_map
+    - pinctrl: qcom: sc8180x: Fix wrong pin numbers
+    - pinctrl: rockchip: Enhance support for IRQ_TYPE_EDGE_BOTH
+    - pinctrl: sunxi: Fix name for A100 R_PIO
+    - NFSv4: Turn off open-by-filehandle and NFS re-export for NFSv4.0
+    - gpio: mpc8xxx: Fix support for IRQ_TYPE_LEVEL_LOW flow_type in mpc85xx
+    - drm/meson: Correct OSD1 global alpha value
+    - drm/meson: Fix OSD1 RGB to YCbCr coefficient
+    - block: blk_queue_enter() / __bio_queue_enter() must return -EAGAIN for
+      nowait
+    - parisc: ccio-dma: Add missing iounmap in error path in ccio_probe()
+    - of/device: Fix up of_dma_configure_id() stub
+    - cifs: revalidate mapping when doing direct writes
+    - cifs: don't send down the destination address to sendmsg for a SOCK_STREAM
+    - cifs: always initialize struct msghdr smb_msg completely
+    - parisc: Allow CONFIG_64BIT with ARCH=parisc
+    - tools/include/uapi: Fix <asm/errno.h> for parisc and xtensa
+    - drm/amdgpu: Don't enable LTR if not supported
+    - drm/amdgpu: move nbio ih_doorbell_range() into ih code for vega
+    - drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega
+    - binder: remove inaccurate mmap_assert_locked()
+    - arm64: dts: juno: Add missing MHU secure-irq
+    - ASoC: nau8824: Fix semaphore unbalance at error paths
+    - regulator: pfuze100: Fix the global-out-of-bounds access in
+      pfuze100_regulator_probe()
+    - scsi: lpfc: Return DID_TRANSPORT_DISRUPTED instead of DID_REQUEUE
+    - rxrpc: Fix local destruction being repeated
+    - rxrpc: Fix calc of resend age
+    - wifi: mac80211_hwsim: check length for virtio packets
+    - ALSA: hda/sigmatel: Keep power up while beep is enabled
+    - ALSA: hda/tegra: Align BDL entry to 4KB boundary
+    - net: usb: qmi_wwan: add Quectel RM520N
+    - afs: Return -EAGAIN, not -EREMOTEIO, when a file already locked
+    - MIPS: OCTEON: irq: Fix octeon_irq_force_ciu_mapping()
+    - drm/panfrost: devfreq: set opp to the recommended one to configure regulator
+    - mksysmap: Fix the mismatch of 'L0' symbols in System.map
+    - video: fbdev: pxa3xx-gcu: Fix integer overflow in pxa3xx_gcu_write
+    - net: Find dst with sk's xfrm policy not ctl_sk
+    - KVM: SEV: add cache flush to solve SEV cache incoherency issues
+    - cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all()
+    - ALSA: hda/sigmatel: Fix unused variable warning for beep power change
+    - Linux 5.15.70
+  * Jammy update: v5.15.69 upstream stable release (LP: #1993010)
+    - NFS: Fix WARN_ON due to unionization of nfs_inode.nrequests
+    - ACPI: resource: skip IRQ override on AMD Zen platforms
+    - ARM: dts: imx: align SPI NOR node name with dtschema
+    - ARM: dts: imx6qdl-kontron-samx6i: fix spi-flash compatible
+    - ARM: dts: at91: fix low limit for CPU regulator
+    - ARM: dts: at91: sama7g5ek: specify proper regulator output ranges
+    - lockdep: Fix -Wunused-parameter for _THIS_IP_
+    - x86/mm: Force-inline __phys_addr_nodebug()
+    - task_stack, x86/cea: Force-inline stack helpers
+    - tracing: hold caller_addr to hardirq_{enable,disable}_ip
+    - tracefs: Only clobber mode/uid/gid on remount if asked
+    - iommu/vt-d: Fix kdump kernels boot failure with scalable mode
+    - Input: goodix - add support for GT1158
+    - platform/surface: aggregator_registry: Add support for Surface Laptop Go 2
+    - drm/msm/rd: Fix FIFO-full deadlock
+    - dt-bindings: iio: gyroscope: bosch,bmg160: correct number of pins
+    - HID: ishtp-hid-clientHID: ishtp-hid-client: Fix comment typo
+    - hid: intel-ish-hid: ishtp: Fix ishtp client sending disordered message
+    - tg3: Disable tg3 device on system reboot to avoid triggering AER
+    - gpio: mockup: remove gpio debugfs when remove device
+    - ieee802154: cc2520: add rc code in cc2520_tx()
+    - Input: iforce - add support for Boeder Force Feedback Wheel
+    - nvmet-tcp: fix unhandled tcp states in nvmet_tcp_state_change()
+    - drm/amd/amdgpu: skip ucode loading if ucode_size == 0
+    - net: dsa: hellcreek: Print warning only once
+    - perf/arm_pmu_platform: fix tests for platform_get_irq() failure
+    - platform/x86: acer-wmi: Acer Aspire One AOD270/Packard Bell Dot keymap fixes
+    - usb: storage: Add ASUS <0x0b05:0x1932> to IGNORE_UAS
+    - mm: Fix TLB flush for not-first PFNMAP mappings in unmap_region()
+    - soc: fsl: select FSL_GUTS driver for DPIO
+    - usb: gadget: f_uac2: clean up some inconsistent indenting
+    - usb: gadget: f_uac2: fix superspeed transfer
+    - RDMA/irdma: Use s/g array in post send only when its valid
+    - Input: goodix - add compatible string for GT1158
+    - Linux 5.15.69
+  * Jammy update: v5.15.68 upstream stable release (LP: #1993003)
+    - net: wwan: iosm: remove pointless null check
+    - efi: libstub: Disable struct randomization
+    - efi: capsule-loader: Fix use-after-free in efi_capsule_write
+    - wifi: iwlegacy: 4965: corrected fix for potential off-by-one overflow in
+      il4965_rs_fill_link_cmd()
+    - fs: only do a memory barrier for the first set_buffer_uptodate()
+    - Revert "mm: kmemleak: take a full lowmem check in kmemleak_*_phys()"
+    - scsi: qla2xxx: Disable ATIO interrupt coalesce for quad port ISP27XX
+    - scsi: megaraid_sas: Fix double kfree()
+    - drm/gem: Fix GEM handle release errors
+    - drm/amdgpu: Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
+      psp_hw_fini
+    - drm/amdgpu: Check num_gfx_rings for gfx v9_0 rb setup.
+    - drm/radeon: add a force flush to delay work when radeon
+    - scsi: ufs: core: Reduce the power mode change timeout
+    - Revert "parisc: Show error if wrong 32/64-bit compiler is being used"
+    - parisc: ccio-dma: Handle kmalloc failure in ccio_init_resources()
+    - parisc: Add runtime check to prevent PA2.0 kernels on PA1.x machines
+    - arm64: cacheinfo: Fix incorrect assignment of signed error value to unsigned
+      fw_level
+    - netfilter: conntrack: work around exceeded receive window
+    - cpufreq: check only freq_table in __resolve_freq()
+    - net/core/skbuff: Check the return value of skb_copy_bits()
+    - md: Flush workqueue md_rdev_misc_wq in md_alloc()
+    - fbdev: fbcon: Destroy mutex on freeing struct fb_info
+    - fbdev: chipsfb: Add missing pci_disable_device() in chipsfb_pci_init()
+    - drm/amdgpu: mmVM_L2_CNTL3 register not initialized correctly
+    - ALSA: pcm: oss: Fix race at SNDCTL_DSP_SYNC
+    - ALSA: emu10k1: Fix out of bounds access in snd_emu10k1_pcm_channel_alloc()
+    - ALSA: aloop: Fix random zeros in capture data when using jiffies timer
+    - ALSA: usb-audio: Fix an out-of-bounds bug in
+      __snd_usb_parse_audio_interface()
+    - tracing: Fix to check event_mutex is held while accessing trigger list
+    - btrfs: zoned: set pseudo max append zone limit in zone emulation mode
+    - vfio/type1: Unpin zero pages
+    - kprobes: Prohibit probes in gate area
+    - debugfs: add debugfs_lookup_and_remove()
+    - sched/debug: fix dentry leak in update_sched_domain_debugfs
+    - drm/amd/display: fix memory leak when using debugfs_lookup()
+    - nvmet: fix a use-after-free
+    - scsi: mpt3sas: Fix use-after-free warning
+    - scsi: lpfc: Add missing destroy_workqueue() in error path
+    - NFS: Further optimisations for 'ls -l'
+    - NFS: Save some space in the inode
+    - NFS: Fix another fsync() issue after a server reboot
+    - cgroup: Elide write-locking threadgroup_rwsem when updating csses on an
+      empty subtree
+    - cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock
+    - ASoC: qcom: sm8250: add missing module owner
+    - RDMA/rtrs-clt: Use the right sg_cnt after ib_dma_map_sg
+    - RDMA/rtrs-srv: Pass the correct number of entries for dma mapped SGL
+    - ARM: dts: imx6qdl-kontron-samx6i: remove duplicated node
+    - soc: imx: gpcv2: Assert reset before ungating clock
+    - regulator: core: Clean up on enable failure
+    - tee: fix compiler warning in tee_shm_register()
+    - RDMA/cma: Fix arguments order in net device validation
+    - soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugs
+    - RDMA/hns: Fix supported page size
+    - RDMA/hns: Fix wrong fixed value of qp->rq.wqe_shift
+    - wifi: wilc1000: fix DMA on stack objects
+    - ARM: at91: pm: fix self-refresh for sama7g5
+    - ARM: at91: pm: fix DDR recalibration when resuming from backup and self-
+      refresh
+    - ARM: dts: at91: sama5d27_wlsom1: specify proper regulator output ranges
+    - ARM: dts: at91: sama5d2_icp: specify proper regulator output ranges
+    - ARM: dts: at91: sama5d27_wlsom1: don't keep ldo2 enabled all the time
+    - ARM: dts: at91: sama5d2_icp: don't keep vdd_other enabled all the time
+    - netfilter: br_netfilter: Drop dst references before setting.
+    - netfilter: nf_tables: clean up hook list when offload flags check fails
+    - RDMA/srp: Set scmnd->result only when scmnd is not NULL
+    - ALSA: usb-audio: Inform the delayed registration more properly
+    - ALSA: usb-audio: Register card again for iface over delayed_register option
+    - rxrpc: Fix ICMP/ICMP6 error handling
+    - rxrpc: Fix an insufficiently large sglist in rxkad_verify_packet_2()
+    - afs: Use the operation issue time instead of the reply time for callbacks
+    - Revert "net: phy: meson-gxl: improve link-up behavior"
+    - sch_sfb: Don't assume the skb is still around after enqueueing to child
+    - tipc: fix shift wrapping bug in map_get()
+    - net: introduce __skb_fill_page_desc_noacc
+    - tcp: TX zerocopy should not sense pfmemalloc status
+    - ice: use bitmap_free instead of devm_kfree
+    - i40e: Fix kernel crash during module removal
+    - iavf: Detach device during reset task
+    - xen-netback: only remove 'hotplug-status' when the vif is actually destroyed
+    - RDMA/siw: Pass a pointer to virt_to_page()
+    - ipv6: sr: fix out-of-bounds read when setting HMAC data.
+    - IB/core: Fix a nested dead lock as part of ODP flow
+    - RDMA/mlx5: Set local port to one when accessing counters
+    - erofs: fix pcluster use-after-free on UP platforms
+    - nvme-tcp: fix UAF when detecting digest errors
+    - nvme-tcp: fix regression that causes sporadic requests to time out
+    - tcp: fix early ETIMEDOUT after spurious non-SACK RTO
+    - nvmet: fix mar and mor off-by-one errors
+    - RDMA/irdma: Report the correct max cqes from query device
+    - RDMA/irdma: Return correct WC error for bind operation failure
+    - RDMA/irdma: Report RNR NAK generation in device caps
+    - sch_sfb: Also store skb len before calling child enqueue
+    - perf script: Fix Cannot print 'iregs' field for hybrid systems
+    - hwmon: (tps23861) fix byte order in resistance register
+    - ASoC: mchp-spdiftx: remove references to mchp_i2s_caps
+    - ASoC: mchp-spdiftx: Fix clang -Wbitfield-constant-conversion
+    - MIPS: loongson32: ls1c: Fix hang during startup
+    - kbuild: disable header exports for UML in a straightforward way
+    - i40e: Refactor tc mqprio checks
+    - i40e: Fix ADQ rate limiting for PF
+    - swiotlb: avoid potential left shift overflow
+    - iommu/amd: use full 64-bit value in build_completion_wait()
+    - s390/boot: fix absolute zero lowcore corruption on boot
+    - hwmon: (mr75203) fix VM sensor allocation when "intel,vm-map" not defined
+    - hwmon: (mr75203) update pvt->v_num and vm_num to the actual number of used
+      sensors
+    - hwmon: (mr75203) fix voltage equation for negative source input
+    - hwmon: (mr75203) fix multi-channel voltage reading
+    - hwmon: (mr75203) enable polling for all VM channels
+    - arm64/bti: Disable in kernel BTI when cross section thunks are broken
+    - [Config] updateconfigs for ARM64_BTI_KERNEL
+    - iommu/vt-d: Correctly calculate sagaw value of IOMMU
+    - [Config] updateconfigs for ARM64_ERRATUM_2457168
+    - arm64: errata: add detection for AMEVCNTR01 incrementing incorrectly
+    - drm/bridge: display-connector: implement bus fmts callbacks
+    - perf machine: Use path__join() to compose a path instead of snprintf(dir,
+      '/', filename)
+    - ARM: at91: ddr: remove CONFIG_SOC_SAMA7 dependency
+    - Linux 5.15.68
+  * Jammy update: v5.15.67 upstream stable release (LP: #1991841)
+    - Linux 5.15.67
+  * Jammy update: v5.15.66 upstream stable release (LP: #1991840)
+    - drm/msm/dsi: fix the inconsistent indenting
+    - drm/msm/dp: delete DP_RECOVERED_CLOCK_OUT_EN to fix tps4
+    - drm/msm/dsi: Fix number of regulators for msm8996_dsi_cfg
+    - drm/msm/dsi: Fix number of regulators for SDM660
+    - platform/x86: pmc_atom: Fix SLP_TYPx bitfield mask
+    - iio: adc: mcp3911: make use of the sign bit
+    - skmsg: Fix wrong last sg check in sk_msg_recvmsg()
+    - bpf: Restrict bpf_sys_bpf to CAP_PERFMON
+    - bpf, cgroup: Fix kernel BUG in purge_effective_progs
+    - ieee802154/adf7242: defer destroy_workqueue call
+    - drm/i915/backlight: extract backlight code to a separate file
+    - drm/i915/display: avoid warnings when registering dual panel backlight
+    - ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
+    - ALSA: hda: intel-nhlt: Correct the handling of fmt_config flexible array
+    - wifi: cfg80211: debugfs: fix return type in ht40allow_map_read()
+    - Revert "xhci: turn off port power in shutdown"
+    - net: sparx5: fix handling uneven length packets in manual extraction
+    - net: smsc911x: Stop and start PHY during suspend and resume
+    - openvswitch: fix memory leak at failed datapath creation
+    - net: dsa: xrs700x: Use irqsave variant for u64 stats update
+    - net: sched: tbf: don't call qdisc_put() while holding tree lock
+    - net/sched: fix netdevice reference leaks in attach_default_qdiscs()
+    - ethernet: rocker: fix sleep in atomic context bug in neigh_timer_handler
+    - mlxbf_gige: compute MDIO period based on i1clk
+    - kcm: fix strp_init() order and cleanup
+    - sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb
+    - tcp: annotate data-race around challenge_timestamp
+    - Revert "sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb"
+    - net/smc: Remove redundant refcount increase
+    - soundwire: qcom: fix device status array range
+    - serial: fsl_lpuart: RS485 RTS polariy is inverse
+    - staging: rtl8712: fix use after free bugs
+    - staging: r8188eu: add firmware dependency
+    - powerpc: align syscall table for ppc32
+    - vt: Clear selection before changing the font
+    - musb: fix USB_MUSB_TUSB6010 dependency
+    - tty: serial: lpuart: disable flow control while waiting for the transmit
+      engine to complete
+    - Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
+    - iio: ad7292: Prevent regulator double disable
+    - iio: adc: mcp3911: use correct formula for AD conversion
+    - misc: fastrpc: fix memory corruption on probe
+    - misc: fastrpc: fix memory corruption on open
+    - USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
+    - mmc: core: Fix UHS-I SD 1.8V workaround branch
+    - mmc: core: Fix inconsistent sd3_bus_mode at UHS-I SD voltage switch failure
+    - binder: fix UAF of ref->proc caused by race condition
+    - binder: fix alloc->vma_vm_mm null-ptr dereference
+    - cifs: fix small mempool leak in SMB2_negotiate()
+    - KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
+    - drm/i915/reg: Fix spelling mistake "Unsupport" -> "Unsupported"
+    - clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops
+    - Revert "clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops"
+    - clk: core: Fix runtime PM sequence in clk_core_unprepare()
+    - Input: rk805-pwrkey - fix module autoloading
+    - clk: bcm: rpi: Fix error handling of raspberrypi_fw_get_rate
+    - clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()
+    - clk: bcm: rpi: Prevent out-of-bounds access
+    - clk: bcm: rpi: Add missing newline
+    - hwmon: (gpio-fan) Fix array out of bounds access
+    - gpio: pca953x: Add mutex_lock for regcache sync in PM
+    - KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
+    - xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
+    - mm: pagewalk: Fix race between unmap and page walker
+    - xen-blkback: Advertise feature-persistent as user requested
+    - xen-blkfront: Advertise feature-persistent as user requested
+    - xen-blkfront: Cache feature_persistent value before advertisement
+    - thunderbolt: Use the actual buffer in tb_async_error()
+    - usb: dwc3: pci: Add support for Intel Raptor Lake
+    - media: mceusb: Use new usb_control_msg_*() routines
+    - xhci: Add grace period after xHC start to prevent premature runtime suspend.
+    - USB: serial: cp210x: add Decagon UCA device id
+    - USB: serial: option: add support for OPPO R11 diag port
+    - USB: serial: option: add Quectel EM060K modem
+    - USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
+    - usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles
+    - usb: typec: intel_pmc_mux: Add new ACPI ID for Meteor Lake IOM device
+    - usb: typec: tcpm: Return ENOTSUPP for power supply prop writes
+    - usb: dwc2: fix wrong order of phy_power_on and phy_init
+    - usb: cdns3: fix issue with rearming ISO OUT endpoint
+    - usb: cdns3: fix incorrect handling TRB_SMM flag for ISOC transfer
+    - USB: cdc-acm: Add Icom PMR F3400 support (0c26:0020)
+    - usb-storage: Add ignore-residue quirk for NXP PN7462AU
+    - s390/hugetlb: fix prepare_hugepage_range() check for 2 GB hugepages
+    - s390: fix nospec table alignments
+    - USB: core: Prevent nested device-reset calls
+    - usb: xhci-mtk: relax TT periodic bandwidth allocation
+    - usb: xhci-mtk: fix bandwidth release issue
+    - usb: gadget: mass_storage: Fix cdrom data transfers on MAC-OS
+    - driver core: Don't probe devices after bus_type.match() probe deferral
+    - wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected
+    - wifi: mac80211: Fix UAF in ieee80211_scan_rx()
+    - net: Use u64_stats_fetch_begin_irq() for stats fetch.
+    - net: mac802154: Fix a condition in the receive path
+    - ALSA: hda/realtek: Add speaker AMP init for Samsung laptops with ALC298
+    - ALSA: seq: oss: Fix data-race for max_midi_devs access
+    - ALSA: seq: Fix data-race at module auto-loading
+    - drm/i915/glk: ECS Liva Q2 needs GLK HDMI port timing quirk
+    - drm/i915: Skip wm/ddb readout for disabled pipes
+    - tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()
+    - kbuild: Add skip_encoding_btf_enum64 option to pahole
+    - usb: dwc3: fix PHY disable sequence
+    - usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup
+    - usb: dwc3: disable USB core PHY management
+    - USB: serial: ch341: fix lost character on LCR updates
+    - USB: serial: ch341: fix disabled rx timer on older devices
+    - Linux 5.15.66
+  * Jammy update: v5.15.65 upstream stable release (LP: #1991831)
+    - mm: Force TLB flush for PFNMAP mappings before unlink_file_vma()
+    - drm/bridge: Add stubs for devm_drm_of_get_bridge when OF is disabled
+    - ACPI: thermal: drop an always true check
+    - drm/vc4: hdmi: Rework power up
+    - drm/vc4: hdmi: Depends on CONFIG_PM
+    - firmware: tegra: bpmp: Do only aligned access to IPC memory area
+    - crypto: lib - remove unneeded selection of XOR_BLOCKS
+    - Drivers: hv: balloon: Support status report for larger page sizes
+    - mm/hugetlb: avoid corrupting page->mapping in hugetlb_mcopy_atomic_pte
+    - [Config] updateconfigs for ARM64_ERRATUM_2441009
+    - arm64: errata: Add Cortex-A510 to the repeat tlbi list
+    - io_uring: Remove unused function req_ref_put
+    - kbuild: Fix include path in scripts/Makefile.modpost
+    - Bluetooth: L2CAP: Fix build errors in some archs
+    - HID: steam: Prevent NULL pointer dereference in steam_{recv,send}_report
+    - udmabuf: Set the DMA mask for the udmabuf device (v2)
+    - media: pvrusb2: fix memory leak in pvr_probe
+    - HID: hidraw: fix memory leak in hidraw_release()
+    - net: fix refcount bug in sk_psock_get (2)
+    - fbdev: fb_pm2fb: Avoid potential divide by zero error
+    - ftrace: Fix NULL pointer dereference in is_ftrace_trampoline when ftrace is
+      dead
+    - bpf: Don't redirect packets with invalid pkt_len
+    - ALSA: usb-audio: Add quirk for LH Labs Geek Out HD Audio 1V5
+    - HID: add Lenovo Yoga C630 battery quirk
+    - HID: AMD_SFH: Add a DMI quirk entry for Chromebooks
+    - HID: asus: ROG NKey: Ignore portion of 0x5a report
+    - HID: thrustmaster: Add sparco wheel and fix array length
+    - drm/i915/gt: Skip TLB invalidations once wedged
+    - mmc: mtk-sd: Clear interrupts when cqe off/disable
+    - mmc: sdhci-of-dwcmshc: add reset call back for rockchip Socs
+    - mmc: sdhci-of-dwcmshc: rename rk3568 to rk35xx
+    - mmc: sdhci-of-dwcmshc: Re-enable support for the BlueField-3 SoC
+    - btrfs: remove root argument from btrfs_unlink_inode()
+    - btrfs: remove no longer needed logic for replaying directory deletes
+    - btrfs: add and use helper for unlinking inode during log replay
+    - btrfs: fix warning during log replay when bumping inode link count
+    - fs/ntfs3: Fix work with fragmented xattr
+    - ASoC: sh: rz-ssi: Improve error handling in rz_ssi_probe() error path
+    - drm/amd/display: Avoid MPC infinite loop
+    - drm/amd/display: Fix HDMI VSIF V3 incorrect issue
+    - drm/amd/display: For stereo keep "FLIP_ANY_FRAME"
+    - drm/amd/display: clear optc underflow before turn off odm clock
+    - ksmbd: return STATUS_BAD_NETWORK_NAME error status if share is not
+      configured
+    - neigh: fix possible DoS due to net iface start/stop loop
+    - s390/hypfs: avoid error message under KVM
+    - ksmbd: don't remove dos attribute xattr on O_TRUNC open
+    - drm/amd/pm: add missing ->fini_microcode interface for Sienna Cichlid
+    - drm/amd/display: Fix pixel clock programming
+    - drm/amdgpu: Increase tlb flush timeout for sriov
+    - drm/amd/display: avoid doing vm_init multiple time
+    - netfilter: conntrack: NF_CONNTRACK_PROCFS should no longer default to y
+    - testing: selftests: nft_flowtable.sh: use random netns names
+    - btrfs: move lockdep class helpers to locking.c
+    - btrfs: fix lockdep splat with reloc root extent buffers
+    - btrfs: tree-checker: check for overlapping extent items
+    - kprobes: don't call disarm_kprobe() for disabled kprobes
+    - btrfs: fix space cache corruption and potential double allocations
+    - android: binder: fix lockdep check on clearing vma
+    - net/af_packet: check len when min_header_len equals to 0
+    - net: neigh: don't call kfree_skb() under spin_lock_irqsave()
+    - Linux 5.15.65
+  * CVE-2022-2663
+    - netfilter: nf_conntrack_irc: Fix forged IP logic
+  * CVE-2022-3061
+    - video: fbdev: i740fb: Error out if 'pixclock' equals zero
+
+  [ Ubuntu: 5.15.0-56.62 ]
+
+  * jammy/linux: 5.15.0-56.62 -proposed tracker (LP: #1997079)
+  * CVE-2022-3566
+    - tcp: Fix data races around icsk->icsk_af_ops.
+  * CVE-2022-3567
+    - ipv6: annotate some data-races around sk->sk_prot
+    - ipv6: Fix data races around sk->sk_prot.
+  * CVE-2022-3621
+    - nilfs2: fix NULL pointer dereference at nilfs_bmap_lookup_at_level()
+  * CVE-2022-3564
+    - Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
+  * CVE-2022-3524
+    - tcp/udp: Fix memory leak in ipv6_renew_options().
+  * CVE-2022-3565
+    - mISDN: fix use-after-free bugs in l1oip timer handlers
+  * CVE-2022-3594
+    - r8152: Rate limit overflow messages
+  * CVE-2022-43945
+    - SUNRPC: Fix svcxdr_init_decode's end-of-buffer calculation
+    - SUNRPC: Fix svcxdr_init_encode's buflen calculation
+    - NFSD: Protect against send buffer overflow in NFSv2 READDIR
+    - NFSD: Protect against send buffer overflow in NFSv3 READDIR
+    - NFSD: Protect against send buffer overflow in NFSv2 READ
+    - NFSD: Protect against send buffer overflow in NFSv3 READ
+    - NFSD: Remove "inline" directives on op_rsize_bop helpers
+    - NFSD: Cap rsize_bop result based on send buffer size
+  * CVE-2022-42703
+    - mm/rmap: Fix anon_vma->degree ambiguity leading to double-reuse
+  * 5.15.0-53-generic no longer boots (LP: #1996740)
+    - drm/amd/display: Add helper for blanking all dp displays
+
+  [ Ubuntu: 5.15.0-53.59 ]
+
+  * Fix blank screen on Thinkpad ADL 4K+ panel (LP: #1980621)
+    - drm/i915: Implement WaEdpLinkRateDataReload
+  * Kernel regresses openjdk on riscv64 (LP: #1992484)
+    - SAUCE: Revert "riscv: mmap with PROT_WRITE but no PROT_READ is invalid"
+  * iavf: SR-IOV VFs error with no traffic flow when MTU greater than 1500
+    (LP: #1983656)
+    - iavf: Fix set max MTU size with port VLAN and jumbo frames
+    - i40e: Fix VF set max MTU size
+  * [Ubuntu 22.04] mpt3sas: Request to include latest bug fix patches
+    (LP: #1965927)
+    - scsi: mpt3sas: Remove scsi_dma_map() error messages
+    - scsi: mpt3sas: Update persistent trigger pages from sysfs interface
+  * ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel
+    systems (LP: #1990985)
+    - ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel
+      systems
+  * Fix resume on AMD platforms when TBT monitor is plugged (LP: #1990920)
+    - SAUCE: Revert "drm/amd/display: Add helper for blanking all dp displays"
+    - drm/amd/display: Detect dpcd_rev when hotplug mst monitor
+    - drm/amd/display: Release remote dc_sink under mst scenario
+  * LSM: Configuring Too Many LSMs Causes Kernel Panic on Boot (LP: #1987998)
+    - SAUCE: LSM: Change Landlock from LSMBLOB_NEEDED to LSMBLOB_NOT_NEEDED
+  * To support Intel Maple Ridge Thunderbolt [8086:1134] (LP: #1990240)
+    - thunderbolt: Add support for Intel Maple Ridge single port controller
+  * Intel graphic driver is not probing[8086:468b] (LP: #1990242)
+    - drm/i915/adl_s: Update ADL-S PCI IDs
+    - drm/i915: Add new ADL-S pci id
+  * Add HDMI codec ID for Intel Raptor Lake (LP: #1989578)
+    - ALSA: hda: Add PCI and HDMI IDs for Intel Raptor Lake
+  * Jammy update: v5.15.64 upstream stable release (LP: #1991717)
+    - wifi: rtlwifi: remove always-true condition pointed out by GCC 12
+    - eth: sun: cassini: remove dead code
+    - audit: fix potential double free on error path from fsnotify_add_inode_mark
+    - cgroup: Fix race condition at rebind_subsystems()
+    - parisc: Make CONFIG_64BIT available for ARCH=parisc64 only
+    - parisc: Fix exception handler for fldw and fstw instructions
+    - kernel/sys_ni: add compat entry for fadvise64_64
+    - x86/entry: Move CLD to the start of the idtentry macro
+    - block: add a bdev_max_zone_append_sectors helper
+    - block: add bdev_max_segments() helper
+    - btrfs: zoned: revive max_zone_append_bytes
+    - btrfs: replace BTRFS_MAX_EXTENT_SIZE with fs_info->max_extent_size
+    - btrfs: convert count_max_extents() to use fs_info->max_extent_size
+    - Input: i8042 - move __initconst to fix code styling warning
+    - Input: i8042 - merge quirk tables
+    - Input: i8042 - add TUXEDO devices to i8042 quirk tables
+    - Input: i8042 - add additional TUXEDO devices to i8042 quirk tables
+    - drivers/base: fix userspace break from using bin_attributes for cpumap and
+      cpulist
+    - scsi: qla2xxx: Fix response queue handler reading stale packets
+    - scsi: qla2xxx: edif: Fix dropped IKE message
+    - btrfs: put initial index value of a directory in a constant
+    - btrfs: pass the dentry to btrfs_log_new_name() instead of the inode
+    - btrfs: remove unnecessary parameter delalloc_start for writepage_delalloc()
+    - riscv: lib: uaccess: fold fixups into body
+    - riscv: lib: uaccess: fix CSR_STATUS SR_SUM bit
+    - xfrm: fix refcount leak in __xfrm_policy_check()
+    - xfrm: clone missing x->lastused in xfrm_do_migrate
+    - xfrm: policy: fix metadata dst->dev xmit null pointer dereference
+    - fs: require CAP_SYS_ADMIN in target namespace for idmapped mounts
+    - net: use eth_hw_addr_set() instead of ether_addr_copy()
+    - Revert "net: macsec: update SCI upon MAC address change."
+    - NFS: Don't allocate nfs_fattr on the stack in __nfs42_ssc_open()
+    - NFSv4.2 fix problems with __nfs42_ssc_open
+    - SUNRPC: RPC level errors should set task->tk_rpc_status
+    - mm/smaps: don't access young/dirty bit if pte unpresent
+    - ntfs: fix acl handling
+    - rose: check NULL rose_loopback_neigh->loopback
+    - r8152: fix the units of some registers for RTL8156A
+    - r8152: fix the RX FIFO settings when suspending
+    - nfc: pn533: Fix use-after-free bugs caused by pn532_cmd_timeout
+    - ice: xsk: Force rings to be sized to power of 2
+    - ice: xsk: prohibit usage of non-balanced queue id
+    - net/mlx5e: Properly disable vlan strip on non-UL reps
+    - net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
+    - net/mlx5e: Fix wrong application of the LRO state
+    - net/mlx5e: Fix wrong tc flag used when set hw-tc-offload off
+    - net: ipa: don't assume SMEM is page-aligned
+    - net: phy: Don't WARN for PHY_READY state in mdio_bus_phy_resume()
+    - net: moxa: get rid of asymmetry in DMA mapping/unmapping
+    - bonding: 802.3ad: fix no transmission of LACPDUs
+    - net: ipvtap - add __init/__exit annotations to module init/exit funcs
+    - netfilter: ebtables: reject blobs that don't provide all entry points
+    - bnxt_en: fix NQ resource accounting during vf creation on 57500 chips
+    - netfilter: nf_tables: disallow updates of implicit chain
+    - netfilter: nf_tables: make table handle allocation per-netns friendly
+    - netfilter: nft_payload: report ERANGE for too long offset and length
+    - netfilter: nft_payload: do not truncate csum_offset and csum_type
+    - netfilter: nf_tables: do not leave chain stats enabled on error
+    - netfilter: nft_osf: restrict osf to ipv4, ipv6 and inet families
+    - netfilter: nft_tunnel: restrict it to netdev family
+    - netfilter: nf_tables: consolidate rule verdict trace call
+    - netfilter: nft_cmp: optimize comparison for 16-bytes
+    - netfilter: bitwise: improve error goto labels
+    - netfilter: nf_tables: upfront validation of data via nft_data_init()
+    - netfilter: nf_tables: disallow jump to implicit chain from set element
+    - netfilter: nf_tables: disallow binding to already bound chain
+    - netfilter: flowtable: add function to invoke garbage collection immediately
+    - netfilter: flowtable: fix stuck flows on cleanup due to pending work
+    - net: Fix data-races around sysctl_[rw]mem_(max|default).
+    - net: Fix data-races around weight_p and dev_weight_[rt]x_bias.
+    - net: Fix data-races around netdev_max_backlog.
+    - net: Fix data-races around netdev_tstamp_prequeue.
+    - ratelimit: Fix data-races in ___ratelimit().
+    - net: Fix data-races around sysctl_optmem_max.
+    - net: Fix a data-race around sysctl_tstamp_allow_data.
+    - net: Fix a data-race around sysctl_net_busy_poll.
+    - net: Fix a data-race around sysctl_net_busy_read.
+    - net: Fix a data-race around netdev_budget.
+    - tcp: expose the tcp_mark_push() and tcp_skb_entail() helpers
+    - mptcp: stop relying on tcp_tx_skb_cache
+    - net: Fix data-races around sysctl_max_skb_frags.
+    - net: Fix a data-race around netdev_budget_usecs.
+    - net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
+    - net: Fix data-races around sysctl_devconf_inherit_init_net.
+    - net: Fix a data-race around sysctl_somaxconn.
+    - ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
+    - i40e: Fix incorrect address type for IPv6 flow rules
+    - rxrpc: Fix locking in rxrpc's sendmsg
+    - ionic: widen queue_lock use around lif init and deinit
+    - ionic: clear broken state on generation change
+    - ionic: fix up issues with handling EAGAIN on FW cmds
+    - ionic: VF initial random MAC address if no assigned mac
+    - net: stmmac: work around sporadic tx issue on link-up
+    - btrfs: fix silent failure when deleting root reference
+    - btrfs: replace: drop assert for suspended replace
+    - btrfs: add info when mount fails due to stale replace target
+    - btrfs: check if root is readonly while setting security xattr
+    - btrfs: fix possible memory leak in btrfs_get_dev_args_from_path()
+    - perf/x86/lbr: Enable the branch type for the Arch LBR by default
+    - x86/unwind/orc: Unwind ftrace trampolines with correct ORC entry
+    - x86/bugs: Add "unknown" reporting for MMIO Stale Data
+    - x86/nospec: Unwreck the RSB stuffing
+    - loop: Check for overflow while configuring loop
+    - writeback: avoid use-after-free after removing device
+    - asm-generic: sections: refactor memory_intersects
+    - mm/damon/dbgfs: avoid duplicate context directory creation
+    - s390/mm: do not trigger write fault when vma does not allow VM_WRITE
+    - bootmem: remove the vmemmap pages from kmemleak in put_page_bootmem
+    - s390: fix double free of GS and RI CBs on fork() failure
+    - fbdev: fbcon: Properly revert changes when vc_resize() failed
+    - Revert "memcg: cleanup racy sum avoidance code"
+    - ACPI: processor: Remove freq Qos request for all CPUs
+    - nouveau: explicitly wait on the fence in nouveau_bo_move_m2mf
+    - smb3: missing inode locks in punch hole
+    - xen/privcmd: fix error exit of privcmd_ioctl_dm_op()
+    - riscv: traps: add missing prototype
+    - io_uring: fix issue with io_write() not always undoing sb_start_write()
+    - mm/hugetlb: fix hugetlb not supporting softdirty tracking
+    - md: call __md_stop_writes in md_stop
+    - mptcp: Fix crash due to tcp_tsorted_anchor was initialized before release
+      skb
+    - arm64: Fix match_list for erratum 1286807 on Arm Cortex-A76
+    - binder_alloc: add missing mmap_lock calls when using the VMA
+    - x86/nospec: Fix i386 RSB stuffing
+    - Documentation/ABI: Mention retbleed vulnerability info file for sysfs
+    - blk-mq: fix io hung due to missing commit_rqs
+    - perf python: Fix build when PYTHON_CONFIG is user supplied
+    - perf/x86/intel/uncore: Fix broken read_counter() for SNB IMC PMU
+    - perf/x86/intel/ds: Fix precise store latency handling
+    - perf stat: Clear evsel->reset_group for each stat run
+    - scsi: ufs: core: Enable link lost interrupt
+    - scsi: storvsc: Remove WQ_MEM_RECLAIM from storvsc_error_wq
+    - bpf: Don't use tnum_range on array range checking for poke descriptors
+    - Linux 5.15.64
+  * Jammy update: v5.15.63 upstream stable release (LP: #1990564)
+    - ALSA: info: Fix llseek return value when using callback
+    - ALSA: hda/realtek: Add quirk for Clevo NS50PU, NS70PU
+    - KVM: Unconditionally get a ref to /dev/kvm module when creating a VM
+    - x86/mm: Use proper mask when setting PUD mapping
+    - rds: add missing barrier to release_refill
+    - locking/atomic: Make test_and_*_bit() ordered on failure
+    - drm/nouveau: recognise GA103
+    - drm/ttm: Fix dummy res NULL ptr deref bug
+    - drm/amd/display: Check correct bounds for stream encoder instances for
+      DCN303
+    - ata: libata-eh: Add missing command name
+    - mmc: pxamci: Fix another error handling path in pxamci_probe()
+    - mmc: pxamci: Fix an error handling path in pxamci_probe()
+    - mmc: meson-gx: Fix an error handling path in meson_mmc_probe()
+    - btrfs: unset reloc control if transaction commit fails in
+      prepare_to_relocate()
+    - btrfs: reset RO counter on block group if we fail to relocate
+    - btrfs: fix lost error handling when looking up extended ref on log replay
+    - cifs: Fix memory leak on the deferred close
+    - x86/kprobes: Fix JNG/JNLE emulation
+    - tracing/eprobes: Do not allow eprobes to use $stack, or % for regs
+    - tracing/eprobes: Do not hardcode $comm as a string
+    - tracing/eprobes: Have event probes be consistent with kprobes and uprobes
+    - tracing/probes: Have kprobes and uprobes use $COMM too
+    - tracing: Have filter accept "common_cpu" to be consistent
+    - ALSA: usb-audio: More comprehensive mixer map for ASUS ROG Zenith II
+    - dt-bindings: usb: mtk-xhci: Allow wakeup interrupt-names to be optional
+    - can: ems_usb: fix clang's -Wunaligned-access warning
+    - apparmor: fix quiet_denied for file rules
+    - Revert "UBUNTU: SAUCE: apparmor: drop prefixing abs root labels with '='"
+    - apparmor: fix absroot causing audited secids to begin with =
+    - apparmor: Fix failed mount permission check error message
+    - apparmor: fix aa_label_asxprint return check
+    - apparmor: fix setting unconfined mode on a loaded profile
+    - apparmor: fix overlapping attachment computation
+    - apparmor: fix reference count leak in aa_pivotroot()
+    - apparmor: Fix memleak in aa_simple_write_to_buffer()
+    - Documentation: ACPI: EINJ: Fix obsolete example
+    - NFSv4.1: Don't decrease the value of seq_nr_highest_sent
+    - NFSv4.1: Handle NFS4ERR_DELAY replies to OP_SEQUENCE correctly
+    - NFSv4: Fix races in the legacy idmapper upcall
+    - NFSv4.1: RECLAIM_COMPLETE must handle EACCES
+    - NFSv4/pnfs: Fix a use-after-free bug in open
+    - BPF: Fix potential bad pointer dereference in bpf_sys_bpf()
+    - bpf: Don't reinit map value in prealloc_lru_pop
+    - bpf: Acquire map uref in .init_seq_private for array map iterator
+    - bpf: Acquire map uref in .init_seq_private for hash map iterator
+    - bpf: Acquire map uref in .init_seq_private for sock local storage map
+      iterator
+    - bpf: Acquire map uref in .init_seq_private for sock{map,hash} iterator
+    - bpf: Check the validity of max_rdwr_access for sock local storage map
+      iterator
+    - can: mcp251x: Fix race condition on receive interrupt
+    - can: j1939: j1939_session_destroy(): fix memory leak of skbs
+    - net: atlantic: fix aq_vec index out of range error
+    - m68k: coldfire/device.c: protect FLEXCAN blocks
+    - sunrpc: fix expiry of auth creds
+    - SUNRPC: Fix xdr_encode_bool()
+    - SUNRPC: Reinitialise the backchannel request buffers before reuse
+    - virtio_net: fix memory leak inside XPD_TX with mergeable
+    - devlink: Fix use-after-free after a failed reload
+    - net: phy: Warn about incorrect mdio_bus_phy_resume() state
+    - net: bcmgenet: Indicate MAC is in charge of PHY PM
+    - net: bgmac: Fix a BUG triggered by wrong bytes_compl
+    - selftests: forwarding: Fix failing tests with old libnet
+    - dt-bindings: arm: qcom: fix Alcatel OneTouch Idol 3 compatibles
+    - pinctrl: nomadik: Fix refcount leak in nmk_pinctrl_dt_subnode_to_map
+    - pinctrl: qcom: msm8916: Allow CAMSS GP clocks to be muxed
+    - pinctrl: amd: Don't save/restore interrupt status and wake status bits
+    - pinctrl: sunxi: Add I/O bias setting for H6 R-PIO
+    - pinctrl: qcom: sm8250: Fix PDC map
+    - Input: exc3000 - fix return value check of wait_for_completion_timeout
+    - octeontx2-pf: Fix NIX_AF_TL3_TL2X_LINKX_CFG register configuration
+    - octeontx2-af: Apply tx nibble fixup always
+    - octeontx2-af: suppress external profile loading warning
+    - octeontx2-af: Fix mcam entry resource leak
+    - octeontx2-af: Fix key checking for source mac
+    - ACPI: property: Return type of acpi_add_nondev_subnodes() should be bool
+    - geneve: do not use RT_TOS for IPv6 flowlabel
+    - mlx5: do not use RT_TOS for IPv6 flowlabel
+    - ipv6: do not use RT_TOS for IPv6 flowlabel
+    - plip: avoid rcu debug splat
+    - vsock: Fix memory leak in vsock_connect()
+    - vsock: Set socket state back to SS_UNCONNECTED in vsock_connect_timeout()
+    - dt-bindings: gpio: zynq: Add missing compatible strings
+    - dt-bindings: arm: qcom: fix Longcheer L8150 compatibles
+    - dt-bindings: arm: qcom: fix MSM8916 MTP compatibles
+    - dt-bindings: arm: qcom: fix MSM8994 boards compatibles
+    - dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
+    - spi: dt-bindings: cadence: add missing 'required'
+    - spi: dt-bindings: zynqmp-qspi: add missing 'required'
+    - ceph: use correct index when encoding client supported features
+    - tools/vm/slabinfo: use alphabetic order when two values are equal
+    - ceph: don't leak snap_rwsem in handle_cap_grant
+    - kbuild: dummy-tools: avoid tmpdir leak in dummy gcc
+    - tools build: Switch to new openssl API for test-libcrypto
+    - NTB: ntb_tool: uninitialized heap data in tool_fn_write()
+    - nfp: ethtool: fix the display error of `ethtool -m DEVNAME`
+    - xen/xenbus: fix return type in xenbus_file_read()
+    - atm: idt77252: fix use-after-free bugs caused by tst_timer
+    - geneve: fix TOS inheriting for ipv4
+    - perf probe: Fix an error handling path in 'parse_perf_probe_command()'
+    - perf parse-events: Fix segfault when event parser gets an error
+    - perf tests: Fix Track with sched_switch test for hybrid case
+    - dpaa2-eth: trace the allocated address instead of page struct
+    - fs/ntfs3: Fix using uninitialized value n when calling indx_read
+    - fs/ntfs3: Fix NULL deref in ntfs_update_mftmirr
+    - fs/ntfs3: Don't clear upper bits accidentally in log_replay()
+    - fs/ntfs3: Fix double free on remount
+    - fs/ntfs3: Do not change mode if ntfs_set_ea failed
+    - fs/ntfs3: Fix missing i_op in ntfs_read_mft
+    - nios2: page fault et.al. are *not* restartable syscalls...
+    - nios2: don't leave NULLs in sys_call_table[]
+    - nios2: traced syscall does need to check the syscall number
+    - nios2: fix syscall restart checks
+    - nios2: restarts apply only to the first sigframe we build...
+    - nios2: add force_successful_syscall_return()
+    - iavf: Fix adminq error handling
+    - iavf: Fix reset error handling
+    - ASoC: SOF: debug: Fix potential buffer overflow by snprintf()
+    - ASoC: tas2770: Set correct FSYNC polarity
+    - ASoC: tas2770: Allow mono streams
+    - ASoC: tas2770: Drop conflicting set_bias_level power setting
+    - ASoC: tas2770: Fix handling of mute/unmute
+    - ASoC: codec: tlv320aic32x4: fix mono playback via I2S
+    - netfilter: nf_tables: use READ_ONCE and WRITE_ONCE for shared generation id
+      access
+    - fs/ntfs3: uninitialized variable in ntfs_set_acl_ex()
+    - netfilter: nf_tables: disallow NFTA_SET_ELEM_KEY_END with
+      NFT_SET_ELEM_INTERVAL_END flag
+    - netfilter: nf_tables: possible module reference underflow in error path
+    - netfilter: nf_tables: really skip inactive sets when allocating name
+    - netfilter: nf_tables: validate NFTA_SET_ELEM_OBJREF based on NFT_SET_OBJECT
+      flag
+    - netfilter: nf_tables: NFTA_SET_ELEM_KEY_END requires concat and interval
+      flags
+    - netfilter: nf_tables: disallow NFT_SET_ELEM_CATCHALL and
+      NFT_SET_ELEM_INTERVAL_END
+    - netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified
+    - powerpc/pci: Fix get_phb_number() locking
+    - spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
+    - net/sunrpc: fix potential memory leaks in rpc_sysfs_xprt_state_change()
+    - net: dsa: mv88e6060: prevent crash on an unused port
+    - mlxsw: spectrum: Clear PTP configuration after unregistering the netdevice
+    - net: moxa: pass pdev instead of ndev to DMA functions
+    - net: fix potential refcount leak in ndisc_router_discovery()
+    - net: dsa: microchip: ksz9477: fix fdb_dump last invalid entry
+    - net: dsa: felix: fix ethtool 256-511 and 512-1023 TX packet counters
+    - net: genl: fix error path memory leak in policy dumping
+    - net: dsa: don't warn in dsa_port_set_state_now() when driver doesn't support
+      it
+    - net: dsa: sja1105: fix buffer overflow in sja1105_setup_devlink_regions()
+    - ice: Ignore EEXIST when setting promisc mode
+    - i2c: imx: Make sure to unregister adapter on remove()
+    - regulator: pca9450: Remove restrictions for regulator-name
+    - i40e: Fix to stop tx_timeout recovery if GLOBR fails
+    - fec: Fix timer capture timing in `fec_ptp_enable_pps()`
+    - stmmac: intel: Add a missing clk_disable_unprepare() call in
+      intel_eth_pci_remove()
+    - igb: Add lock to avoid data race
+    - kbuild: fix the modules order between drivers and libs
+    - gcc-plugins: Undefine LATENT_ENTROPY_PLUGIN when plugin disabled for a file
+    - tracing/eprobes: Fix reading of string fields
+    - drm/imx/dcss: get rid of HPD warning message
+    - ASoC: SOF: Intel: hda: Define rom_status_reg in sof_intel_dsp_desc
+    - ASoC: SOF: Intel: hda: Fix potential buffer overflow by snprintf()
+    - drm/meson: Fix refcount bugs in meson_vpu_has_available_connectors()
+    - drm/sun4i: dsi: Prevent underflow when computing packet sizes
+    - net: qrtr: start MHI channel after endpoit creation
+    - KVM: arm64: Treat PMCR_EL1.LC as RES1 on asymmetric systems
+    - KVM: arm64: Reject 32bit user PSTATE on asymmetric systems
+    - HID: multitouch: new device class fix Lenovo X12 trackpad sticky
+    - PCI: Add ACS quirk for Broadcom BCM5750x NICs
+    - platform/chrome: cros_ec_proto: don't show MKBP version if unsupported
+    - usb: cdns3 fix use-after-free at workaround 2
+    - usb: cdns3: fix random warning message when driver load
+    - usb: gadget: uvc: calculate the number of request depending on framesize
+    - usb: gadget: uvc: call uvc uvcg_warn on completed status instead of
+      uvcg_info
+    - PCI: aardvark: Fix reporting Slot capabilities on emulated bridge
+    - irqchip/tegra: Fix overflow implicit truncation warnings
+    - drm/meson: Fix overflow implicit truncation warnings
+    - clk: ti: Stop using legacy clkctrl names for omap4 and 5
+    - scsi: ufs: ufs-mediatek: Fix the timing of configuring device regulators
+    - usb: host: ohci-ppc-of: Fix refcount leak bug
+    - usb: renesas: Fix refcount leak bug
+    - usb: dwc2: gadget: remove D+ pull-up while no vbus with usb-role-switch
+    - vboxguest: Do not use devm for irq
+    - clk: qcom: ipq8074: dont disable gcc_sleep_clk_src
+    - uacce: Handle parent device removal or parent driver module rmmod
+    - zram: do not lookup algorithm in backends table
+    - clk: qcom: clk-alpha-pll: fix clk_trion_pll_configure description
+    - scsi: lpfc: Prevent buffer overflow crashes in debugfs with malformed user
+      input
+    - scsi: lpfc: Fix possible memory leak when failing to issue CMF WQE
+    - gadgetfs: ep_io - wait until IRQ finishes
+    - coresight: etm4x: avoid build failure with unrolled loops
+    - habanalabs/gaudi: fix shift out of bounds
+    - habanalabs/gaudi: mask constant value before cast
+    - mmc: tmio: avoid glitches when resetting
+    - pinctrl: intel: Check against matching data instead of ACPI companion
+    - cxl: Fix a memory leak in an error handling path
+    - PCI/ACPI: Guard ARM64-specific mcfg_quirks
+    - um: add "noreboot" command line option for PANIC_TIMEOUT=-1 setups
+    - dmaengine: dw-axi-dmac: do not print NULL LLI during error
+    - dmaengine: dw-axi-dmac: ignore interrupt if no descriptor
+    - RDMA/rxe: Limit the number of calls to each tasklet
+    - csky/kprobe: reclaim insn_slot on kprobe unregistration
+    - selftests/kprobe: Do not test for GRP/ without event failures
+    - dmaengine: sprd: Cleanup in .remove() after pm_runtime_get_sync() failed
+    - openrisc: io: Define iounmap argument as volatile
+    - phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks
+    - md: Notify sysfs sync_completed in md_reap_sync_thread()
+    - nvmet-tcp: fix lockdep complaint on nvmet_tcp_wq flush during queue teardown
+    - drivers:md:fix a potential use-after-free bug
+    - ext4: avoid remove directory when directory is corrupted
+    - ext4: avoid resizing to a partial cluster size
+    - lib/list_debug.c: Detect uninitialized lists
+    - tty: serial: Fix refcount leak bug in ucc_uart.c
+    - KVM: PPC: Book3S HV: Fix "rm_exit" entry in debugfs timings
+    - vfio: Clear the caps->buf to NULL after free
+    - mips: cavium-octeon: Fix missing of_node_put() in octeon2_usb_clocks_start
+    - iommu/io-pgtable-arm-v7s: Add a quirk to allow pgtable PA up to 35bit
+    - modules: Ensure natural alignment for .altinstructions and __bug_table
+      sections
+    - ASoC: rsnd: care default case on rsnd_ssiu_busif_err_irq_ctrl()
+    - riscv: dts: sifive: Add fu740 topology information
+    - riscv: dts: canaan: Add k210 topology information
+    - riscv: mmap with PROT_WRITE but no PROT_READ is invalid
+    - RISC-V: Add fast call path of crash_kexec()
+    - watchdog: export lockup_detector_reconfigure
+    - powerpc/32: Set an IBAT covering up to _einittext during init
+    - powerpc/32: Don't always pass -mcpu=powerpc to the compiler
+    - ovl: warn if trusted xattr creation fails
+    - powerpc/ioda/iommu/debugfs: Generate unique debugfs entries
+    - ALSA: core: Add async signal helpers
+    - ALSA: timer: Use deferred fasync helper
+    - ALSA: control: Use deferred fasync helper
+    - f2fs: fix to avoid use f2fs_bug_on() in f2fs_new_node_page()
+    - f2fs: fix to do sanity check on segment type in build_sit_entries()
+    - smb3: check xattr value length earlier
+    - powerpc/64: Init jump labels before parse_early_param()
+    - venus: pm_helpers: Fix warning in OPP during probe
+    - video: fbdev: i740fb: Check the argument of i740_calc_vclk()
+    - MIPS: tlbex: Explicitly compare _PAGE_NO_EXEC against 0
+    - can: j1939: j1939_sk_queue_activate_next_locked(): replace WARN_ON_ONCE with
+      netdev_warn_once()
+    - scsi: ufs: ufs-mediatek: Fix build error and type mismatch
+    - xfs: flush inodegc workqueue tasks before cancel
+    - xfs: reserve quota for dir expansion when linking/unlinking files
+    - xfs: reserve quota for target dir expansion when renaming files
+    - xfs: remove infinite loop when reserving free block pool
+    - xfs: always succeed at setting the reserve pool size
+    - xfs: fix overfilling of reserve pool
+    - xfs: fix soft lockup via spinning in filestream ag selection loop
+    - xfs: revert "xfs: actually bump warning counts when we send warnings"
+    - xfs: reject crazy array sizes being fed to XFS_IOC_GETBMAP*
+    - Linux 5.15.63
+  * Jammy update: v5.15.62 upstream stable release (LP: #1990554)
+    - io_uring: use original request task for inflight tracking
+    - tee: add overflow check in register_shm_helper()
+    - net_sched: cls_route: disallow handle of 0
+    - ksmbd: prevent out of bound read for SMB2_WRITE
+    - ksmbd: fix heap-based overflow in set_ntacl_dacl()
+    - btrfs: only write the sectors in the vertical stripe which has data stripes
+    - btrfs: raid56: don't trust any cached sector in __raid56_parity_recover()
+    - Linux 5.15.62
+  * Jammy update: v5.15.61 upstream stable release (LP: #1990162)
+    - Makefile: link with -z noexecstack --no-warn-rwx-segments
+    - x86: link vdso and boot with -z noexecstack --no-warn-rwx-segments
+    - Revert "pNFS: nfs3_set_ds_client should set NFS_CS_NOPING"
+    - scsi: Revert "scsi: qla2xxx: Fix disk failure to rediscover"
+    - pNFS/flexfiles: Report RDMA connection errors to the server
+    - NFSD: Clean up the show_nf_flags() macro
+    - nfsd: eliminate the NFSD_FILE_BREAK_* flags
+    - ALSA: usb-audio: Add quirk for Behringer UMC202HD
+    - ALSA: bcd2000: Fix a UAF bug on the error path of probing
+    - ALSA: hda/realtek: Add quirk for Clevo NV45PZ
+    - ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
+    - wifi: mac80211_hwsim: fix race condition in pending packet
+    - wifi: mac80211_hwsim: add back erroneously removed cast
+    - wifi: mac80211_hwsim: use 32-bit skb cookie
+    - add barriers to buffer_uptodate and set_buffer_uptodate
+    - lockd: detect and reject lock arguments that overflow
+    - HID: hid-input: add Surface Go battery quirk
+    - HID: wacom: Only report rotation for art pen
+    - HID: wacom: Don't register pad_input for touch switch
+    - KVM: nVMX: Snapshot pre-VM-Enter BNDCFGS for !nested_run_pending case
+    - KVM: nVMX: Snapshot pre-VM-Enter DEBUGCTL for !nested_run_pending case
+    - KVM: SVM: Don't BUG if userspace injects an interrupt with GIF=0
+    - KVM: s390: pv: don't present the ecall interrupt twice
+    - KVM: x86: Split kvm_is_valid_cr4() and export only the non-vendor bits
+    - KVM: nVMX: Let userspace set nVMX MSR to any _host_ supported value
+    - KVM: nVMX: Account for KVM reserved CR4 bits in consistency checks
+    - KVM: nVMX: Inject #UD if VMXON is attempted with incompatible CR0/CR4
+    - KVM: x86: Mark TSS busy during LTR emulation _after_ all fault checks
+    - KVM: x86: Set error code to segment selector on LLDT/LTR non-canonical #GP
+    - KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
+    - KVM: x86: Tag kvm_mmu_x86_module_init() with __init
+    - KVM: x86: do not report preemption if the steal time cache is stale
+    - KVM: x86: revalidate steal time cache if MSR value changes
+    - riscv: set default pm_power_off to NULL
+    - ALSA: hda/conexant: Add quirk for LENOVO 20149 Notebook model
+    - ALSA: hda/cirrus - support for iMac 12,1 model
+    - ALSA: hda/realtek: Add quirk for another Asus K42JZ model
+    - ALSA: hda/realtek: Add a quirk for HP OMEN 15 (8786) mute LED
+    - tty: vt: initialize unicode screen buffer
+    - vfs: Check the truncate maximum size in inode_newsize_ok()
+    - fs: Add missing umask strip in vfs_tmpfile
+    - thermal: sysfs: Fix cooling_device_stats_setup() error code path
+    - fbcon: Fix boundary checks for fbcon=vc:n1-n2 parameters
+    - fbcon: Fix accelerated fbdev scrolling while logo is still shown
+    - usbnet: Fix linkwatch use-after-free on disconnect
+    - fix short copy handling in copy_mc_pipe_to_iter()
+    - crypto: ccp - Use kzalloc for sev ioctl interfaces to prevent kernel memory
+      leak
+    - ovl: drop WARN_ON() dentry is NULL in ovl_encode_fh()
+    - parisc: Fix device names in /proc/iomem
+    - parisc: Drop pa_swapper_pg_lock spinlock
+    - parisc: Check the return value of ioremap() in lba_driver_probe()
+    - parisc: io_pgetevents_time64() needs compat syscall in 32-bit compat mode
+    - riscv:uprobe fix SR_SPIE set/clear handling
+    - dt-bindings: riscv: fix SiFive l2-cache's cache-sets
+    - RISC-V: kexec: Fixup use of smp_processor_id() in preemptible context
+    - RISC-V: Fixup get incorrect user mode PC for kernel mode regs
+    - RISC-V: Fixup schedule out issue in machine_crash_shutdown()
+    - RISC-V: Add modules to virtual kernel memory layout dump
+    - rtc: rx8025: fix 12/24 hour mode detection on RX-8035
+    - drm/gem: Properly annotate WW context on drm_gem_lock_reservations() error
+    - drm/shmem-helper: Add missing vunmap on error
+    - drm/vc4: hdmi: Disable audio if dmas property is present but empty
+    - drm/hyperv-drm: Include framebuffer and EDID headers
+    - drm/nouveau: fix another off-by-one in nvbios_addr
+    - drm/nouveau: Don't pm_runtime_put_sync(), only pm_runtime_put_autosuspend()
+    - drm/nouveau/acpi: Don't print error when we get -EINPROGRESS from pm_runtime
+    - drm/nouveau/kms: Fix failure path for creating DP connectors
+    - drm/amdgpu: Check BO's requested pinning domains against its
+      preferred_domains
+    - bpf: Fix KASAN use-after-free Read in compute_effective_progs
+    - btrfs: reject log replay if there is unsupported RO compat flag
+    - mtd: rawnand: arasan: Fix clock rate in NV-DDR
+    - mtd: rawnand: arasan: Update NAND bus clock instead of system clock
+    - um: Remove straying parenthesis
+    - um: seed rng using host OS rng
+    - iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
+    - iio: light: isl29028: Fix the warning in isl29028_remove()
+    - scsi: sg: Allow waiting for commands to complete on removed device
+    - scsi: qla2xxx: Fix incorrect display of max frame size
+    - scsi: qla2xxx: Zero undefined mailbox IN registers
+    - soundwire: qcom: Check device status before reading devid
+    - ksmbd: fix memory leak in smb2_handle_negotiate
+    - ksmbd: prevent out of bound read for SMB2_TREE_CONNNECT
+    - ksmbd: fix use-after-free bug in smb2_tree_disconect
+    - fuse: limit nsec
+    - fuse: ioctl: translate ENOSYS
+    - serial: mvebu-uart: uart2 error bits clearing
+    - md-raid10: fix KASAN warning
+    - mbcache: don't reclaim used entries
+    - mbcache: add functions to delete entry if unused
+    - media: [PATCH] pci: atomisp_cmd: fix three missing checks on list iterator
+    - ia64, processor: fix -Wincompatible-pointer-types in ia64_get_irr()
+    - PCI: Add defines for normal and subtractive PCI bridges
+    - powerpc/fsl-pci: Fix Class Code of PCIe Root Port
+    - powerpc/ptdump: Fix display of RW pages on FSL_BOOK3E
+    - powerpc/powernv: Avoid crashing if rng is NULL
+    - MIPS: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
+    - coresight: Clear the connection field properly
+    - usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
+    - USB: HCD: Fix URB giveback issue in tasklet function
+    - ARM: dts: uniphier: Fix USB interrupts for PXs2 SoC
+    - arm64: dts: uniphier: Fix USB interrupts for PXs3 SoC
+    - usb: dwc3: gadget: refactor dwc3_repare_one_trb
+    - usb: dwc3: gadget: fix high speed multiplier setting
+    - netfilter: nf_tables: fix null deref due to zeroed list head
+    - epoll: autoremove wakers even more aggressively
+    - x86: Handle idle=nomwait cmdline properly for x86_idle
+    - arch: make TRACE_IRQFLAGS_NMI_SUPPORT generic
+    - arm64: Do not forget syscall when starting a new thread.
+    - arm64: fix oops in concurrently setting insn_emulation sysctls
+    - ext2: Add more validity checks for inode counts
+    - sched/fair: Introduce SIS_UTIL to search idle CPU based on sum of util_avg
+    - genirq: Don't return error on missing optional irq_request_resources()
+    - irqchip/mips-gic: Only register IPI domain when SMP is enabled
+    - genirq: GENERIC_IRQ_IPI depends on SMP
+    - sched/core: Always flush pending blk_plug
+    - irqchip/mips-gic: Check the return value of ioremap() in gic_of_init()
+    - wait: Fix __wait_event_hrtimeout for RT/DL tasks
+    - ARM: dts: imx6ul: add missing properties for sram
+    - ARM: dts: imx6ul: change operating-points to uint32-matrix
+    - ARM: dts: imx6ul: fix keypad compatible
+    - ARM: dts: imx6ul: fix csi node compatible
+    - ARM: dts: imx6ul: fix lcdif node compatible
+    - ARM: dts: imx6ul: fix qspi node compatible
+    - ARM: dts: BCM5301X: Add DT for Meraki MR26
+    - ARM: dts: ux500: Fix Codina accelerometer mounting matrix
+    - ARM: dts: ux500: Fix Gavini accelerometer mounting matrix
+    - spi: synquacer: Add missing clk_disable_unprepare()
+    - ARM: OMAP2+: display: Fix refcount leak bug
+    - ARM: OMAP2+: pdata-quirks: Fix refcount leak bug
+    - ACPI: EC: Remove duplicate ThinkPad X1 Carbon 6th entry from DMI quirks
+    - ACPI: EC: Drop the EC_FLAGS_IGNORE_DSDT_GPE quirk
+    - ACPI: PM: save NVS memory for Lenovo G40-45
+    - ACPI: LPSS: Fix missing check in register_device_clock()
+    - ARM: dts: qcom: sdx55: Fix the IRQ trigger type for UART
+    - arm64: dts: qcom: ipq8074: fix NAND node name
+    - arm64: dts: allwinner: a64: orangepi-win: Fix LED node name
+    - ARM: shmobile: rcar-gen2: Increase refcount for new reference
+    - firmware: tegra: Fix error check return value of debugfs_create_file()
+    - hwmon: (dell-smm) Add Dell XPS 13 7390 to fan control whitelist
+    - hwmon: (sht15) Fix wrong assumptions in device remove callback
+    - PM: hibernate: defer device probing when resuming from hibernation
+    - selinux: fix memleak in security_read_state_kernel()
+    - selinux: Add boundary check in put_entry()
+    - kasan: test: Silence GCC 12 warnings
+    - drm/amdgpu: Remove one duplicated ef removal
+    - powerpc/64s: Disable stack variable initialisation for prom_init
+    - spi: spi-rspi: Fix PIO fallback on RZ platforms
+    - ARM: findbit: fix overflowing offset
+    - meson-mx-socinfo: Fix refcount leak in meson_mx_socinfo_init
+    - arm64: dts: renesas: beacon: Fix regulator node names
+    - spi: spi-altera-dfl: Fix an error handling path
+    - ARM: bcm: Fix refcount leak in bcm_kona_smc_init
+    - ACPI: processor/idle: Annotate more functions to live in cpuidle section
+    - ARM: dts: imx7d-colibri-emmc: add cpu1 supply
+    - soc: renesas: r8a779a0-sysc: Fix A2DP1 and A2CV[2357] PDR values
+    - scsi: hisi_sas: Use managed PCI functions
+    - dt-bindings: iio: accel: Add DT binding doc for ADXL355
+    - soc: amlogic: Fix refcount leak in meson-secure-pwrc.c
+    - arm64: dts: renesas: Fix thermal-sensors on single-zone sensors
+    - x86/pmem: Fix platform-device leak in error path
+    - ARM: dts: ast2500-evb: fix board compatible
+    - ARM: dts: ast2600-evb: fix board compatible
+    - ARM: dts: ast2600-evb-a1: fix board compatible
+    - arm64: dts: mt8192: Fix idle-states nodes naming scheme
+    - arm64: dts: mt8192: Fix idle-states entry-method
+    - arm64: select TRACE_IRQFLAGS_NMI_SUPPORT
+    - arm64: cpufeature: Allow different PMU versions in ID_DFR0_EL1
+    - locking/lockdep: Fix lockdep_init_map_*() confusion
+    - arm64: dts: qcom: sc7180: Remove ipa_fw_mem node on trogdor
+    - soc: fsl: guts: machine variable might be unset
+    - block: fix infinite loop for invalid zone append
+    - ARM: dts: qcom: mdm9615: add missing PMIC GPIO reg
+    - ARM: OMAP2+: Fix refcount leak in omapdss_init_of
+    - ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
+    - arm64: dts: qcom: sdm630: disable GPU by default
+    - arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
+    - arm64: dts: qcom: sdm630: fix gpu's interconnect path
+    - arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf
+    - cpufreq: zynq: Fix refcount leak in zynq_get_revision
+    - regulator: qcom_smd: Fix pm8916_pldo range
+    - ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP
+    - ARM: dts: qcom-msm8974: fix irq type on blsp2_uart1
+    - soc: qcom: ocmem: Fix refcount leak in of_get_ocmem
+    - soc: qcom: aoss: Fix refcount leak in qmp_cooling_devices_register
+    - ARM: dts: qcom: pm8841: add required thermal-sensor-cells
+    - bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
+    - stack: Declare {randomize_,}kstack_offset to fix Sparse warnings
+    - arm64: dts: qcom: msm8916: Fix typo in pronto remoteproc node
+    - ACPI: APEI: explicit init of HEST and GHES in apci_init()
+    - drivers/iio: Remove all strcpy() uses
+    - ACPI: VIOT: Fix ACS setup
+    - arm64: dts: qcom: sm6125: Move sdc2 pinctrl from seine-pdx201 to sm6125
+    - arm64: dts: qcom: sm6125: Append -state suffix to pinctrl nodes
+    - arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
+    - arm64: dts: mt7622: fix BPI-R64 WPS button
+    - arm64: tegra: Fixup SYSRAM references
+    - arm64: tegra: Update Tegra234 BPMP channel addresses
+    - arm64: tegra: Mark BPMP channels as no-memory-wc
+    - arm64: tegra: Fix SDMMC1 CD on P2888
+    - erofs: avoid consecutive detection for Highmem memory
+    - blk-mq: don't create hctx debugfs dir until q->debugfs_dir is created
+    - spi: Fix simplification of devm_spi_register_controller
+    - spi: tegra20-slink: fix UAF in tegra_slink_remove()
+    - hwmon: (drivetemp) Add module alias
+    - blktrace: Trace remapped requests correctly
+    - PM: domains: Ensure genpd_debugfs_dir exists before remove
+    - dm writecache: return void from functions
+    - dm writecache: count number of blocks read, not number of read bios
+    - dm writecache: count number of blocks written, not number of write bios
+    - dm writecache: count number of blocks discarded, not number of discard bios
+    - regulator: of: Fix refcount leak bug in of_get_regulation_constraints()
+    - soc: qcom: Make QCOM_RPMPD depend on PM
+    - arm64: dts: qcom: qcs404: Fix incorrect USB2 PHYs assignment
+    - irqdomain: Report irq number for NOMAP domains
+    - drivers/perf: arm_spe: Fix consistency of SYS_PMSCR_EL1.CX
+    - nohz/full, sched/rt: Fix missed tick-reenabling bug in dequeue_task_rt()
+    - x86/extable: Fix ex_handler_msr() print condition
+    - selftests/seccomp: Fix compile warning when CC=clang
+    - thermal/tools/tmon: Include pthread and time headers in tmon.h
+    - dm: return early from dm_pr_call() if DM device is suspended
+    - pwm: sifive: Simplify offset calculation for PWMCMP registers
+    - pwm: sifive: Ensure the clk is enabled exactly once per running PWM
+    - pwm: sifive: Shut down hardware only after pwmchip_remove() completed
+    - pwm: lpc18xx-sct: Reduce number of devm memory allocations
+    - pwm: lpc18xx-sct: Simplify driver by not using pwm_[gs]et_chip_data()
+    - pwm: lpc18xx: Fix period handling
+    - drm/dp: Export symbol / kerneldoc fixes for DP AUX bus
+    - drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated
+      function
+    - ath10k: do not enforce interrupt trigger type
+    - drm/st7735r: Fix module autoloading for Okaya RH128128T
+    - drm/panel: Fix build error when CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y &&
+      CONFIG_DRM_DISPLAY_HELPER=m
+    - wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
+    - ath11k: fix netdev open race
+    - drm/mipi-dbi: align max_chunk to 2 in spi_transfer
+    - ath11k: Fix incorrect debug_mask mappings
+    - drm/radeon: fix potential buffer overflow in ni_set_mc_special_registers()
+    - drm/mediatek: Modify dsi funcs to atomic operations
+    - drm/mediatek: Separate poweron/poweroff from enable/disable and define new
+      funcs
+    - drm/mediatek: Add pull-down MIPI operation in mtk_dsi_poweroff function
+    - drm/meson: encoder_hdmi: switch to bridge DRM_BRIDGE_ATTACH_NO_CONNECTOR
+    - drm/meson: encoder_hdmi: Fix refcount leak in meson_encoder_hdmi_init
+    - drm/bridge: lt9611uxc: Cancel only driver's work
+    - i2c: npcm: Remove own slave addresses 2:10
+    - i2c: npcm: Correct slave role behavior
+    - i2c: mxs: Silence a clang warning
+    - virtio-gpu: fix a missing check to avoid NULL dereference
+    - drm/shmem-helper: Unexport drm_gem_shmem_create_with_handle()
+    - drm/shmem-helper: Export dedicated wrappers for GEM object functions
+    - drm/shmem-helper: Pass GEM shmem object in public interfaces
+    - drm/virtio: Fix NULL vs IS_ERR checking in virtio_gpu_object_shmem_init
+    - drm: adv7511: override i2c address of cec before accessing it
+    - crypto: sun8i-ss - do not allocate memory when handling hash requests
+    - crypto: sun8i-ss - fix error codes in allocate_flows()
+    - net: fix sk_wmem_schedule() and sk_rmem_schedule() errors
+    - can: netlink: allow configuring of fixed bit rates without need for
+      do_set_bittiming callback
+    - can: netlink: allow configuring of fixed data bit rates without need for
+      do_set_data_bittiming callback
+    - i2c: Fix a potential use after free
+    - crypto: sun8i-ss - fix infinite loop in sun8i_ss_setup_ivs()
+    - media: atmel: atmel-sama7g5-isc: fix warning in configs without OF
+    - media: tw686x: Register the irq at the end of probe
+    - media: imx-jpeg: Correct some definition according specification
+    - media: imx-jpeg: Leave a blank space before the configuration data
+    - media: imx-jpeg: Add pm-runtime support for imx-jpeg
+    - media: imx-jpeg: use NV12M to represent non contiguous NV12
+    - media: imx-jpeg: Set V4L2_BUF_FLAG_LAST at eos
+    - media: imx-jpeg: Refactor function mxc_jpeg_parse
+    - media: imx-jpeg: Identify and handle precision correctly
+    - media: imx-jpeg: Handle source change in a function
+    - media: imx-jpeg: Support dynamic resolution change
+    - media: imx-jpeg: Align upwards buffer size
+    - media: imx-jpeg: Implement drain using v4l2-mem2mem helpers
+    - wifi: iwlegacy: 4965: fix potential off-by-one overflow in
+      il4965_rs_fill_link_cmd()
+    - drm/radeon: fix incorrrect SPDX-License-Identifiers
+    - rcutorture: Warn on individual rcu_torture_init() error conditions
+    - rcutorture: Don't cpuhp_remove_state() if cpuhp_setup_state() failed
+    - rcutorture: Fix ksoftirqd boosting timing and iteration
+    - test_bpf: fix incorrect netdev features
+    - crypto: ccp - During shutdown, check SEV data pointer before using
+    - drm: bridge: adv7511: Add check for mipi_dsi_driver_register
+    - media: imx-jpeg: Disable slot interrupt when frame done
+    - drm/mcde: Fix refcount leak in mcde_dsi_bind
+    - media: hdpvr: fix error value returns in hdpvr_read
+    - media: v4l2-mem2mem: prevent pollerr when last_buffer_dequeued is set
+    - media: driver/nxp/imx-jpeg: fix a unexpected return value problem
+    - media: tw686x: Fix memory leak in tw686x_video_init
+    - drm/vc4: plane: Remove subpixel positioning check
+    - drm/vc4: plane: Fix margin calculations for the right/bottom edges
+    - drm/bridge: Add a function to abstract away panels
+    - drm/vc4: dsi: Switch to devm_drm_of_get_bridge
+    - drm/vc4: Use of_device_get_match_data()
+    - drm/vc4: dsi: Release workaround buffer and DMA
+    - drm/vc4: dsi: Correct DSI divider calculations
+    - drm/vc4: dsi: Correct pixel order for DSI0
+    - drm/vc4: dsi: Register dsi0 as the correct vc4 encoder type
+    - drm/vc4: dsi: Fix dsi0 interrupt support
+    - drm/vc4: dsi: Add correct stop condition to vc4_dsi_encoder_disable
+      iteration
+    - drm/vc4: hdmi: Fix HPD GPIO detection
+    - drm/vc4: hdmi: Avoid full hdmi audio fifo writes
+    - drm/vc4: hdmi: Reset HDMI MISC_CONTROL register
+    - drm/vc4: hdmi: Fix timings for interlaced modes
+    - drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes
+    - crypto: arm64/gcm - Select AEAD for GHASH_ARM64_CE
+    - selftests/xsk: Destroy BPF resources only when ctx refcount drops to 0
+    - drm/rockchip: vop: Don't crash for invalid duplicate_state()
+    - drm/rockchip: Fix an error handling path rockchip_dp_probe()
+    - drm/mediatek: dpi: Remove output format of YUV
+    - drm/mediatek: dpi: Only enable dpi after the bridge is enabled
+    - drm: bridge: sii8620: fix possible off-by-one
+    - hinic: Use the bitmap API when applicable
+    - net: hinic: fix bug that ethtool get wrong stats
+    - net: hinic: avoid kernel hung in hinic_get_stats64()
+    - drm/msm/mdp5: Fix global state lock backoff
+    - crypto: hisilicon/sec - don't sleep when in softirq
+    - crypto: hisilicon - Kunpeng916 crypto driver don't sleep when in softirq
+    - media: platform: mtk-mdp: Fix mdp_ipi_comm structure alignment
+    - drm/msm: Avoid dirtyfb stalls on video mode displays (v2)
+    - drm/msm/dpu: Fix for non-visible planes
+    - mt76: mt76x02u: fix possible memory leak in __mt76x02u_mcu_send_msg
+    - mt76: mt7615: do not update pm stats in case of error
+    - ieee80211: add EHT 1K aggregation definitions
+    - mt76: mt7921: fix aggregation subframes setting to HE max
+    - mt76: mt7921: enlarge maximum VHT MPDU length to 11454
+    - mediatek: mt76: mac80211: Fix missing of_node_put() in mt76_led_init()
+    - mediatek: mt76: eeprom: fix missing of_node_put() in
+      mt76_find_power_limits_node()
+    - skmsg: Fix invalid last sg check in sk_msg_recvmsg()
+    - drm/exynos/exynos7_drm_decon: free resources when clk_set_parent() failed.
+    - tcp: make retransmitted SKB fit into the send window
+    - libbpf: Fix the name of a reused map
+    - selftests: timers: valid-adjtimex: build fix for newer toolchains
+    - selftests: timers: clocksource-switch: fix passing errors from child
+    - bpf: Fix subprog names in stack traces.
+    - fs: check FMODE_LSEEK to control internal pipe splicing
+    - media: cedrus: h265: Fix flag name
+    - media: hantro: postproc: Fix motion vector space size
+    - media: hantro: Simplify postprocessor
+    - media: hevc: Embedded indexes in RPS
+    - media: staging: media: hantro: Fix typos
+    - wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()
+    - wifi: p54: Fix an error handling path in p54spi_probe()
+    - wifi: p54: add missing parentheses in p54_flush()
+    - selftests/bpf: fix a test for snprintf() overflow
+    - libbpf: fix an snprintf() overflow check
+    - can: pch_can: do not report txerr and rxerr during bus-off
+    - can: rcar_can: do not report txerr and rxerr during bus-off
+    - can: sja1000: do not report txerr and rxerr during bus-off
+    - can: hi311x: do not report txerr and rxerr during bus-off
+    - can: sun4i_can: do not report txerr and rxerr during bus-off
+    - can: kvaser_usb_hydra: do not report txerr and rxerr during bus-off
+    - can: kvaser_usb_leaf: do not report txerr and rxerr during bus-off
+    - can: usb_8dev: do not report txerr and rxerr during bus-off
+    - can: error: specify the values of data[5..7] of CAN error frames
+    - can: pch_can: pch_can_error(): initialize errc before using it
+    - Bluetooth: hci_intel: Add check for platform_driver_register
+    - i2c: cadence: Support PEC for SMBus block read
+    - i2c: mux-gpmux: Add of_node_put() when breaking out of loop
+    - wifi: wil6210: debugfs: fix uninitialized variable use in
+      `wil_write_file_wmi()`
+    - wifi: iwlwifi: mvm: fix double list_add at iwl_mvm_mac_wake_tx_queue
+    - wifi: libertas: Fix possible refcount leak in if_usb_probe()
+    - media: cedrus: hevc: Add check for invalid timestamp
+    - net/mlx5e: Remove WARN_ON when trying to offload an unsupported TLS
+      cipher/version
+    - net/mlx5e: Fix the value of MLX5E_MAX_RQ_NUM_MTTS
+    - net/mlx5: Adjust log_max_qp to be 18 at most
+    - crypto: hisilicon/hpre - don't use GFP_KERNEL to alloc mem during softirq
+    - crypto: inside-secure - Add missing MODULE_DEVICE_TABLE for of
+    - crypto: hisilicon/sec - fix auth key size error
+    - inet: add READ_ONCE(sk->sk_bound_dev_if) in INET_MATCH()
+    - ipv6: add READ_ONCE(sk->sk_bound_dev_if) in INET6_MATCH()
+    - net: allow unbound socket for packets in VRF when tcp_l3mdev_accept set
+    - netdevsim: fib: Fix reference count leak on route deletion failure
+    - wifi: rtw88: check the return value of alloc_workqueue()
+    - iavf: Fix max_rate limiting
+    - iavf: Fix 'tc qdisc show' listing too many queues
+    - netdevsim: Avoid allocation warnings triggered from user space
+    - net: rose: fix netdev reference changes
+    - net: ionic: fix error check for vlan flags in ionic_set_nic_features()
+    - dccp: put dccp_qpolicy_full() and dccp_qpolicy_push() in the same lock
+    - net: usb: make USB_RTL8153_ECM non user configurable
+    - wireguard: ratelimiter: use hrtimer in selftest
+    - wireguard: allowedips: don't corrupt stack when detecting overflow
+    - HID: amd_sfh: Don't show client init failed as error when discovery fails
+    - clk: renesas: r9a06g032: Fix UART clkgrp bitsel
+    - mtd: maps: Fix refcount leak in of_flash_probe_versatile
+    - mtd: maps: Fix refcount leak in ap_flash_init
+    - mtd: rawnand: meson: Fix a potential double free issue
+    - of: check previous kernel's ima-kexec-buffer against memory bounds
+    - scsi: qla2xxx: edif: Reduce Initiator-Initiator thrashing
+    - scsi: qla2xxx: edif: Fix potential stuck session in sa update
+    - scsi: qla2xxx: edif: Reduce connection thrash
+    - scsi: qla2xxx: edif: Fix inconsistent check of db_flags
+    - scsi: qla2xxx: edif: Synchronize NPIV deletion with authentication
+      application
+    - scsi: qla2xxx: edif: Add retry for ELS passthrough
+    - scsi: qla2xxx: edif: Fix n2n discovery issue with secure target
+    - scsi: qla2xxx: edif: Fix n2n login retry for secure device
+    - KVM: SVM: Unwind "speculative" RIP advancement if INTn injection "fails"
+    - KVM: SVM: Stuff next_rip on emulated INT3 injection if NRIPS is supported
+    - phy: samsung: exynosautov9-ufs: correct TSRV register configurations
+    - PCI: microchip: Fix refcount leak in mc_pcie_init_irq_domains()
+    - PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
+    - HID: cp2112: prevent a buffer overflow in cp2112_xfer()
+    - mtd: sm_ftl: Fix deadlock caused by cancel_work_sync in sm_release
+    - mtd: partitions: Fix refcount leak in parse_redboot_of
+    - mtd: parsers: ofpart: Fix refcount leak in bcm4908_partitions_fw_offset
+    - mtd: st_spi_fsm: Add a clk_disable_unprepare() in .probe()'s error path
+    - PCI: mediatek-gen3: Fix refcount leak in mtk_pcie_init_irq_domains()
+    - fpga: altera-pr-ip: fix unsigned comparison with less than zero
+    - usb: host: Fix refcount leak in ehci_hcd_ppc_of_probe
+    - usb: ohci-nxp: Fix refcount leak in ohci_hcd_nxp_probe
+    - usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()
+    - usb: xhci: tegra: Fix error check
+    - netfilter: xtables: Bring SPDX identifier back
+    - scsi: qla2xxx: edif: Send LOGO for unexpected IKE message
+    - scsi: qla2xxx: edif: Reduce disruption due to multiple app start
+    - scsi: qla2xxx: edif: Fix no login after app start
+    - scsi: qla2xxx: edif: Tear down session if keys have been removed
+    - scsi: qla2xxx: edif: Fix session thrash
+    - scsi: qla2xxx: edif: Fix no logout on delete for N2N
+    - iio: accel: bma400: Fix the scale min and max macro values
+    - platform/chrome: cros_ec: Always expose last resume result
+    - iio: accel: bma400: Reordering of header files
+    - clk: mediatek: reset: Fix written reset bit offset
+    - lib/test_hmm: avoid accessing uninitialized pages
+    - memremap: remove support for external pgmap refcounts
+    - mm/memremap: fix memunmap_pages() race with get_dev_pagemap()
+    - KVM: Don't set Accessed/Dirty bits for ZERO_PAGE
+    - mwifiex: Ignore BTCOEX events from the 88W8897 firmware
+    - mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv
+    - scsi: iscsi: Allow iscsi_if_stop_conn() to be called from kernel
+    - scsi: iscsi: Add helper to remove a session from the kernel
+    - scsi: iscsi: Fix session removal on shutdown
+    - dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics
+    - mtd: dataflash: Add SPI ID table
+    - clk: qcom: camcc-sm8250: Fix halt on boot by reducing driver's init level
+    - misc: rtsx: Fix an error handling path in rtsx_pci_probe()
+    - driver core: fix potential deadlock in __driver_attach
+    - clk: qcom: clk-krait: unlock spin after mux completion
+    - clk: qcom: gcc-msm8939: Add missing SYSTEM_MM_NOC_BFDCD_CLK_SRC
+    - clk: qcom: gcc-msm8939: Fix bimc_ddr_clk_src rcgr base address
+    - clk: qcom: gcc-msm8939: Add missing system_mm_noc_bfdcd_clk_src
+    - clk: qcom: gcc-msm8939: Point MM peripherals to system_mm_noc clock
+    - usb: host: xhci: use snprintf() in xhci_decode_trb()
+    - RDMA/rxe: Fix deadlock in rxe_do_local_ops()
+    - clk: qcom: ipq8074: fix NSS core PLL-s
+    - clk: qcom: ipq8074: SW workaround for UBI32 PLL lock
+    - clk: qcom: ipq8074: fix NSS port frequency tables
+    - clk: qcom: ipq8074: set BRANCH_HALT_DELAY flag for UBI clocks
+    - clk: qcom: camcc-sdm845: Fix topology around titan_top power domain
+    - clk: qcom: camcc-sm8250: Fix topology around titan_top power domain
+    - clk: qcom: clk-rcg2: Fail Duty-Cycle configuration if MND divider is not
+      enabled.
+    - clk: qcom: clk-rcg2: Make sure to not write d=0 to the NMD register
+    - mm/mempolicy: fix get_nodes out of bound access
+    - PCI: dwc: Stop link on host_init errors and de-initialization
+    - PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
+    - PCI: dwc: Disable outbound windows only for controllers using iATU
+    - PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
+    - PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
+    - PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
+    - soundwire: bus_type: fix remove and shutdown support
+    - soundwire: revisit driver bind/unbind and callbacks
+    - KVM: arm64: Don't return from void function
+    - dmaengine: sf-pdma: Add multithread support for a DMA channel
+    - PCI: endpoint: Don't stop controller when unbinding endpoint function
+    - scsi: qla2xxx: Check correct variable in qla24xx_async_gffid()
+    - intel_th: Fix a resource leak in an error handling path
+    - intel_th: msu-sink: Potential dereference of null pointer
+    - intel_th: msu: Fix vmalloced buffers
+    - binder: fix redefinition of seq_file attributes
+    - staging: rtl8192u: Fix sleep in atomic context bug in
+      dm_fsync_timer_callback
+    - mmc: sdhci-of-esdhc: Fix refcount leak in esdhc_signal_voltage_switch
+    - mmc: mxcmmc: Silence a clang warning
+    - mmc: renesas_sdhi: Get the reset handle early in the probe
+    - memstick/ms_block: Fix some incorrect memory allocation
+    - memstick/ms_block: Fix a memory leak
+    - mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
+    - of: device: Fix missing of_node_put() in of_dma_set_restricted_buffer
+    - mmc: block: Add single read for 4k sector cards
+    - KVM: s390: pv: leak the topmost page table when destroy fails
+    - PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
+    - scsi: smartpqi: Fix DMA direction for RAID requests
+    - xtensa: iss/network: provide release() callback
+    - xtensa: iss: fix handling error cases in iss_net_configure()
+    - usb: gadget: udc: amd5536 depends on HAS_DMA
+    - usb: aspeed-vhub: Fix refcount leak bug in ast_vhub_init_desc()
+    - usb: dwc3: core: Deprecate GCTL.CORESOFTRESET
+    - usb: dwc3: core: Do not perform GCTL_CORE_SOFTRESET during bootup
+    - usb: dwc3: qcom: fix missing optional irq warnings
+    - eeprom: idt_89hpesx: uninitialized data in idt_dbgfs_csr_write()
+    - phy: stm32: fix error return in stm32_usbphyc_phy_init
+    - interconnect: imx: fix max_node_id
+    - um: random: Don't initialise hwrng struct with zero
+    - RDMA/irdma: Fix a window for use-after-free
+    - RDMA/irdma: Fix VLAN connection with wildcard address
+    - RDMA/irdma: Fix setting of QP context err_rq_idx_valid field
+    - RDMA/rtrs-srv: Fix modinfo output for stringify
+    - RDMA/rtrs: Fix warning when use poll mode on client side.
+    - RDMA/rtrs: Replace duplicate check with is_pollqueue helper
+    - RDMA/rtrs: Introduce destroy_cq helper
+    - RDMA/rtrs: Do not allow sessname to contain special symbols / and .
+    - RDMA/rtrs: Rename rtrs_sess to rtrs_path
+    - RDMA/rtrs-srv: Rename rtrs_srv_sess to rtrs_srv_path
+    - RDMA/rtrs-clt: Rename rtrs_clt_sess to rtrs_clt_path
+    - RDMA/rtrs-clt: Replace list_next_or_null_rr_rcu with an inline function
+    - RDMA/qedr: Fix potential memory leak in __qedr_alloc_mr()
+    - RDMA/hns: Fix incorrect clearing of interrupt status register
+    - RDMA/siw: Fix duplicated reported IW_CM_EVENT_CONNECT_REPLY event
+    - iio: cros: Register FIFO callback after sensor is registered
+    - clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
+    - RDMA/hfi1: fix potential memory leak in setup_base_ctxt()
+    - gpio: gpiolib-of: Fix refcount bugs in of_mm_gpiochip_add_data()
+    - HID: mcp2221: prevent a buffer overflow in mcp_smbus_write()
+    - HID: amd_sfh: Add NULL check for hid device
+    - dmaengine: imx-dma: Cast of_device_get_match_data() with (uintptr_t)
+    - scripts/gdb: lx-dmesg: read records individually
+    - scripts/gdb: fix 'lx-dmesg' on 32 bits arch
+    - RDMA/rxe: Fix mw bind to allow any consumer key portion
+    - mmc: cavium-octeon: Add of_node_put() when breaking out of loop
+    - mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
+    - HID: alps: Declare U1_UNICORN_LEGACY support
+    - RDMA/rxe: For invalidate compare according to set keys in mr
+    - PCI: tegra194: Fix Root Port interrupt handling
+    - PCI: tegra194: Fix link up retry sequence
+    - HID: amd_sfh: Handle condition of "no sensors"
+    - USB: serial: fix tty-port initialized comments
+    - usb: cdns3: change place of 'priv_ep' assignment in
+      cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
+    - mtd: spi-nor: fix spi_nor_spimem_setup_op() call in
+      spi_nor_erase_{sector,chip}()
+    - KVM: nVMX: Set UMIP bit CR4_FIXED1 MSR when emulating UMIP
+    - platform/olpc: Fix uninitialized data in debugfs write
+    - RDMA/srpt: Duplicate port name members
+    - RDMA/srpt: Introduce a reference count in struct srpt_device
+    - RDMA/srpt: Fix a use-after-free
+    - android: binder: stop saving a pointer to the VMA
+    - mm/mmap.c: fix missing call to vm_unacct_memory in mmap_region
+    - selftests: kvm: set rax before vmcall
+    - of/fdt: declared return type does not match actual return type
+    - RDMA/mlx5: Add missing check for return value in get namespace flow
+    - RDMA/rxe: Add memory barriers to kernel queues
+    - RDMA/rxe: Remove the is_user members of struct rxe_sq/rxe_rq/rxe_srq
+    - RDMA/rxe: Fix error unwind in rxe_create_qp()
+    - block/rnbd-srv: Set keep_id to true after mutex_trylock
+    - null_blk: fix ida error handling in null_add_dev()
+    - nvme: use command_id instead of req->tag in trace_nvme_complete_rq()
+    - nvme: define compat_ioctl again to unbreak 32-bit userspace.
+    - nvme: disable namespace access for unsupported metadata
+    - nvme: don't return an error from nvme_configure_metadata
+    - nvme: catch -ENODEV from nvme_revalidate_zones again
+    - block/bio: remove duplicate append pages code
+    - block: ensure iov_iter advances for added pages
+    - jbd2: fix outstanding credits assert in jbd2_journal_commit_transaction()
+    - ext4: recover csum seed of tmp_inode after migrating to extents
+    - jbd2: fix assertion 'jh->b_frozen_data == NULL' failure when journal aborted
+    - usb: cdns3: Don't use priv_dev uninitialized in cdns3_gadget_ep_enable()
+    - opp: Fix error check in dev_pm_opp_attach_genpd()
+    - ASoC: cros_ec_codec: Fix refcount leak in cros_ec_codec_platform_probe
+    - ASoC: samsung: Fix error handling in aries_audio_probe
+    - ASoC: imx-audmux: Silence a clang warning
+    - ASoC: mediatek: mt8173: Fix refcount leak in mt8173_rt5650_rt5676_dev_probe
+    - ASoC: mt6797-mt6351: Fix refcount leak in mt6797_mt6351_dev_probe
+    - ASoC: codecs: da7210: add check for i2c_add_driver
+    - ASoC: mediatek: mt8173-rt5650: Fix refcount leak in mt8173_rt5650_dev_probe
+    - serial: 8250: Export ICR access helpers for internal use
+    - serial: 8250: dma: Allow driver operations before starting DMA transfers
+    - serial: 8250_dw: Store LSR into lsr_saved_flags in dw8250_tx_wait_empty()
+    - ASoC: codecs: msm8916-wcd-digital: move gains from SX_TLV to S8_TLV
+    - ASoC: codecs: wcd9335: move gains from SX_TLV to S8_TLV
+    - rpmsg: char: Add mutex protection for rpmsg_eptdev_open()
+    - rpmsg: mtk_rpmsg: Fix circular locking dependency
+    - remoteproc: k3-r5: Fix refcount leak in k3_r5_cluster_of_init
+    - selftests/livepatch: better synchronize test_klp_callbacks_busy
+    - profiling: fix shift too large makes kernel panic
+    - remoteproc: imx_rproc: Fix refcount leak in imx_rproc_addr_init
+    - ASoC: samsung: h1940_uda1380: include proepr GPIO consumer header
+    - powerpc/perf: Optimize clearing the pending PMI and remove WARN_ON for PMI
+      check in power_pmu_disable
+    - ASoC: samsung: change gpiod_speaker_power and rx1950_audio from global to
+      static variables
+    - tty: n_gsm: Delete gsmtty open SABM frame when config requester
+    - tty: n_gsm: fix user open not possible at responder until initiator open
+    - tty: n_gsm: fix tty registration before control channel open
+    - tty: n_gsm: fix wrong queuing behavior in gsm_dlci_data_output()
+    - tty: n_gsm: fix missing timer to handle stalled links
+    - tty: n_gsm: fix non flow control frames during mux flow off
+    - tty: n_gsm: fix packet re-transmission without open control channel
+    - tty: n_gsm: fix race condition in gsmld_write()
+    - tty: n_gsm: fix resource allocation order in gsm_activate_mux()
+    - ASoC: qcom: Fix missing of_node_put() in
+      asoc_qcom_lpass_cpu_platform_probe()
+    - ASoC: imx-card: Fix DSD/PDM mclk frequency
+    - remoteproc: qcom: wcnss: Fix handling of IRQs
+    - vfio/ccw: Do not change FSM state in subchannel event
+    - serial: 8250_fsl: Don't report FE, PE and OE twice
+    - tty: n_gsm: fix wrong T1 retry count handling
+    - tty: n_gsm: fix DM command
+    - tty: n_gsm: fix missing corner cases in gsmld_poll()
+    - MIPS: vdso: Utilize __pa() for gic_pfn
+    - swiotlb: fail map correctly with failed io_tlb_default_mem
+    - ASoC: mt6359: Fix refcount leak bug
+    - serial: 8250_bcm7271: Save/restore RTS in suspend/resume
+    - iommu/exynos: Handle failed IOMMU device registration properly
+    - 9p: fix a bunch of checkpatch warnings
+    - 9p: Drop kref usage
+    - 9p: Add client parameter to p9_req_put()
+    - net: 9p: fix refcount leak in p9_read_work() error handling
+    - MIPS: Fixed __debug_virt_addr_valid()
+    - rpmsg: qcom_smd: Fix refcount leak in qcom_smd_parse_edge
+    - kfifo: fix kfifo_to_user() return type
+    - lib/smp_processor_id: fix imbalanced instrumentation_end() call
+    - proc: fix a dentry lock race between release_task and lookup
+    - remoteproc: qcom: pas: Check if coredump is enabled
+    - remoteproc: sysmon: Wait for SSCTL service to come up
+    - mfd: t7l66xb: Drop platform disable callback
+    - mfd: max77620: Fix refcount leak in max77620_initialise_fps
+    - iommu/arm-smmu: qcom_iommu: Add of_node_put() when breaking out of loop
+    - perf tools: Fix dso_id inode generation comparison
+    - s390/dump: fix old lowcore virtual vs physical address confusion
+    - s390/maccess: fix semantics of memcpy_real() and its callers
+    - s390/crash: fix incorrect number of bytes to copy to user space
+    - s390/zcore: fix race when reading from hardware system area
+    - ASoC: fsl_asrc: force cast the asrc_format type
+    - ASoC: fsl-asoc-card: force cast the asrc_format type
+    - ASoC: fsl_easrc: use snd_pcm_format_t type for sample_format
+    - ASoC: imx-card: use snd_pcm_format_t type for asrc_format
+    - ASoC: qcom: q6dsp: Fix an off-by-one in q6adm_alloc_copp()
+    - fuse: Remove the control interface for virtio-fs
+    - ASoC: audio-graph-card: Add of_node_put() in fail path
+    - watchdog: sp5100_tco: Fix a memory leak of EFCH MMIO resource
+    - watchdog: armada_37xx_wdt: check the return value of devm_ioremap() in
+      armada_37xx_wdt_probe()
+    - video: fbdev: amba-clcd: Fix refcount leak bugs
+    - video: fbdev: sis: fix typos in SiS_GetModeID()
+    - ASoC: mchp-spdifrx: disable end of block interrupt on failures
+    - powerpc/32: Call mmu_mark_initmem_nx() regardless of data block mapping.
+    - powerpc/32: Do not allow selection of e5500 or e6500 CPUs on PPC32
+    - powerpc/iommu: Fix iommu_table_in_use for a small default DMA window case
+    - powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and
+      alias
+    - tty: serial: fsl_lpuart: correct the count of break characters
+    - s390/dump: fix os_info virtual vs physical address confusion
+    - s390/smp: cleanup target CPU callback starting
+    - s390/smp: cleanup control register update routines
+    - s390/maccess: rework absolute lowcore accessors
+    - s390/smp: enforce lowcore protection on CPU restart
+    - f2fs: fix to remove F2FS_COMPR_FL and tag F2FS_NOCOMP_FL at the same time
+    - powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
+    - powerpc/xive: Fix refcount leak in xive_get_max_prio
+    - powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
+    - perf symbol: Fail to read phdr workaround
+    - kprobes: Forbid probing on trampoline and BPF code areas
+    - x86/bus_lock: Don't assume the init value of DEBUGCTLMSR.BUS_LOCK_DETECT to
+      be zero
+    - powerpc/pci: Fix PHB numbering when using opal-phbid
+    - genelf: Use HAVE_LIBCRYPTO_SUPPORT, not the never defined HAVE_LIBCRYPTO
+    - scripts/faddr2line: Fix vmlinux detection on arm64
+    - sched/deadline: Merge dl_task_can_attach() and dl_cpu_busy()
+    - sched, cpuset: Fix dl_cpu_busy() panic due to empty cs->cpus_allowed
+    - x86/numa: Use cpumask_available instead of hardcoded NULL check
+    - video: fbdev: arkfb: Fix a divide-by-zero bug in ark_set_pixclock()
+    - tools/thermal: Fix possible path truncations
+    - sched: Fix the check of nr_running at queue wakelist
+    - sched: Remove the limitation of WF_ON_CPU on wakelist if wakee cpu is idle
+    - sched/core: Do not requeue task on CPU excluded from cpus_mask
+    - f2fs: allow compression for mmap files in compress_mode=user
+    - f2fs: do not allow to decompress files have FI_COMPRESS_RELEASED
+    - video: fbdev: vt8623fb: Check the size of screen before memset_io()
+    - video: fbdev: arkfb: Check the size of screen before memset_io()
+    - video: fbdev: s3fb: Check the size of screen before memset_io()
+    - scsi: ufs: core: Correct ufshcd_shutdown() flow
+    - scsi: zfcp: Fix missing auto port scan and thus missing target ports
+    - scsi: qla2xxx: Fix imbalance vha->vref_count
+    - scsi: qla2xxx: Fix discovery issues in FC-AL topology
+    - scsi: qla2xxx: Turn off multi-queue for 8G adapters
+    - scsi: qla2xxx: Fix crash due to stale SRB access around I/O timeouts
+    - scsi: qla2xxx: Fix excessive I/O error messages by default
+    - scsi: qla2xxx: Fix erroneous mailbox timeout after PCI error injection
+    - scsi: qla2xxx: Wind down adapter after PCIe error
+    - scsi: qla2xxx: Fix losing FCP-2 targets on long port disable with I/Os
+    - scsi: qla2xxx: Fix losing target when it reappears during delete
+    - scsi: qla2xxx: Fix losing FCP-2 targets during port perturbation tests
+    - x86/bugs: Enable STIBP for IBPB mitigated RETBleed
+    - ftrace/x86: Add back ftrace_expected assignment
+    - x86/kprobes: Update kcb status flag after singlestepping
+    - x86/olpc: fix 'logical not is only applied to the left hand side'
+    - SMB3: fix lease break timeout when multiple deferred close handles for the
+      same file.
+    - Input: gscps2 - check return value of ioremap() in gscps2_probe()
+    - __follow_mount_rcu(): verify that mount_lock remains unchanged
+    - spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
+    - drm/mediatek: Allow commands to be sent during video mode
+    - drm/mediatek: Keep dsi as LP00 before dcs cmds transfer
+    - crypto: blake2s - remove shash module
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component
+    - usbnet: smsc95xx: Don't clear read-only PHY interrupt
+    - usbnet: smsc95xx: Avoid link settings race on interrupt reception
+    - firmware: arm_scpi: Ensure scpi_info is not assigned if the probe fails
+    - scsi: lpfc: SLI path split: Refactor lpfc_iocbq
+    - scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
+    - scsi: lpfc: SLI path split: Refactor SCSI paths
+    - scsi: lpfc: Remove extra atomic_inc on cmd_pending in queuecommand after
+      VMID
+    - intel_th: pci: Add Meteor Lake-P support
+    - intel_th: pci: Add Raptor Lake-S PCH support
+    - intel_th: pci: Add Raptor Lake-S CPU support
+    - KVM: set_msr_mce: Permit guests to ignore single-bit ECC errors
+    - KVM: x86: Signal #GP, not -EPERM, on bad WRMSR(MCi_CTL/STATUS)
+    - iommu/vt-d: avoid invalid memory access via node_online(NUMA_NO_NODE)
+    - PCI/AER: Iterate over error counters instead of error strings
+    - PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
+    - serial: 8250_pci: Refactor the loop in pci_ite887x_init()
+    - serial: 8250_pci: Replace dev_*() by pci_*() macros
+    - serial: 8250: Fold EndRun device support into OxSemi Tornado code
+    - serial: 8250: Add proper clock handling for OxSemi PCIe devices
+    - tty: 8250: Add support for Brainboxes PX cards.
+    - dm writecache: set a default MAX_WRITEBACK_JOBS
+    - kexec, KEYS, s390: Make use of built-in and secondary keyring for signature
+      verification
+    - dm thin: fix use-after-free crash in dm_sm_register_threshold_callback
+    - net/9p: Initialize the iounit field during fid creation
+    - ARM: remove some dead code
+    - timekeeping: contribute wall clock to rng on time change
+    - locking/csd_lock: Change csdlock_debug from early_param to __setup
+    - block: remove the struct blk_queue_ctx forward declaration
+    - block: don't allow the same type rq_qos add more than once
+    - btrfs: ensure pages are unlocked on cow_file_range() failure
+    - btrfs: reset block group chunk force if we have to wait
+    - btrfs: properly flag filesystem with BTRFS_FEATURE_INCOMPAT_BIG_METADATA
+    - ACPI: CPPC: Do not prevent CPPC from working in the future
+    - powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
+    - KVM: x86/pmu: Introduce the ctrl_mask value for fixed counter
+    - KVM: VMX: Mark all PERF_GLOBAL_(OVF)_CTRL bits reserved if there's no vPMU
+    - KVM: x86/pmu: Ignore pmu->global_ctrl check if vPMU doesn't support
+      global_ctrl
+    - KVM: VMX: Add helper to check if the guest PMU has PERF_GLOBAL_CTRL
+    - KVM: nVMX: Attempt to load PERF_GLOBAL_CTRL on nVMX xfer iff it exists
+    - dm raid: fix address sanitizer warning in raid_status
+    - dm raid: fix address sanitizer warning in raid_resume
+    - tracing: Add '__rel_loc' using trace event macros
+    - tracing: Avoid -Warray-bounds warning for __rel_loc macro
+    - ext4: update s_overhead_clusters in the superblock during an on-line resize
+    - ext4: fix extent status tree race in writeback error recovery path
+    - ext4: add EXT4_INODE_HAS_XATTR_SPACE macro in xattr.h
+    - ext4: fix use-after-free in ext4_xattr_set_entry
+    - ext4: correct max_inline_xattr_value_size computing
+    - ext4: correct the misjudgment in ext4_iget_extra_inode
+    - ext4: fix warning in ext4_iomap_begin as race between bmap and write
+    - ext4: check if directory block is within i_size
+    - ext4: make sure ext4_append() always allocates new block
+    - ext4: remove EA inode entry from mbcache on inode eviction
+    - ext4: use kmemdup() to replace kmalloc + memcpy
+    - ext4: unindent codeblock in ext4_xattr_block_set()
+    - ext4: fix race when reusing xattr blocks
+    - KEYS: asymmetric: enforce SM2 signature use pkey algo
+    - tpm: eventlog: Fix section mismatch for DEBUG_SECTION_MISMATCH
+    - xen-blkback: fix persistent grants negotiation
+    - xen-blkback: Apply 'feature_persistent' parameter when connect
+    - xen-blkfront: Apply 'feature_persistent' parameter when connect
+    - powerpc: Fix eh field when calling lwarx on PPC32
+    - tracing: Use a struct alignof to determine trace event field alignment
+    - mac80211: fix a memory leak where sta_info is not freed
+    - tcp: fix over estimation in sk_forced_mem_schedule()
+    - crypto: lib/blake2s - reduce stack frame usage in self test
+    - Revert "mwifiex: fix sleep in atomic context bugs caused by dev_coredumpv"
+    - Revert "s390/smp: enforce lowcore protection on CPU restart"
+    - drm/bridge: tc358767: Fix (e)DP bridge endpoint parsing in dedicated
+      function
+    - net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
+    - drm/vc4: change vc4_dma_range_matches from a global to static
+    - tracing/perf: Avoid -Warray-bounds warning for __rel_loc macro
+    - drm/msm: Fix dirtyfb refcounting
+    - drm/meson: Fix refcount leak in meson_encoder_hdmi_init
+    - io_uring: mem-account pbuf buckets
+    - Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm regression
+    - drm/bridge: Move devm_drm_of_get_bridge to bridge/panel.c
+    - scsi: lpfc: Fix locking for lpfc_sli_iocbq_lookup()
+    - scsi: lpfc: Fix element offset in __lpfc_sli_release_iocbq_s4()
+    - scsi: lpfc: Resolve some cleanup issues following SLI path refactoring
+    - Linux 5.15.61
+  * CVE-2022-3028
+    - af_key: Do not call xfrm_probe_algs in parallel
+  * CVE-2022-2978
+    - fs: fix UAF/GPF bug in nilfs_mdt_destroy
+  * CVE-2022-40768
+    - scsi: stex: Properly zero out the passthrough command structure
+
+  [ Ubuntu: 5.15.0-52.58 ]
+
+  * CVE-2022-2602
+    - SAUCE: io_uring/af_unix: defer registered files gc to io_uring release
+    - SAUCE: io_uring/af_unix: fix memleak during unix GC
+  * CVE-2022-41674
+    - mac80211: move CRC into struct ieee802_11_elems
+    - mac80211: mlme: find auth challenge directly
+    - mac80211: mesh: clean up rx_bcn_presp API
+    - mac80211: always allocate struct ieee802_11_elems
+    - mac80211: fix memory leaks with element parsing
+    - SAUCE: wifi: cfg80211: fix u8 overflow in
+      cfg80211_update_notlisted_nontrans()
+    - SAUCE: wifi: cfg80211/mac80211: reject bad MBSSID elements
+    - SAUCE: wifi: cfg80211: ensure length byte is present before access
+    - SAUCE: wifi: mac80211_hwsim: avoid mac80211 warning on bad rate
+    - SAUCE: wifi: cfg80211: update hidden BSSes to avoid WARN_ON
+  * CVE-2022-42722
+    - SAUCE: wifi: mac80211: fix crash in beacon protection for P2P-device
+  * CVE-2022-42721
+    - SAUCE: wifi: cfg80211: avoid nontransmitted BSS list corruption
+  * CVE-2022-42720
+    - SAUCE: wifi: cfg80211: fix BSS refcounting bugs
+  * CVE-2022-42719
+    - SAUCE: wifi: mac80211: fix MBSSID parsing use-after-free
+
+  [ Ubuntu: 5.15.0-50.56 ]
+
+  * jammy/linux: 5.15.0-50.56 -proposed tracker (LP: #1990148)
+  * CVE-2022-3176
+    - io_uring: refactor poll update
+    - io_uring: move common poll bits
+    - io_uring: kill poll linking optimisation
+    - io_uring: inline io_poll_complete
+    - io_uring: correct fill events helpers types
+    - io_uring: clean cqe filling functions
+    - io_uring: poll rework
+    - io_uring: remove poll entry from list when canceling all
+    - io_uring: bump poll refs to full 31-bits
+    - io_uring: fail links when poll fails
+    - io_uring: fix wrong arm_poll error handling
+    - io_uring: fix UAF due to missing POLLFREE handling
+  * ip/nexthop: fix default address selection for connected nexthop
+    (LP: #1988809)
+    - selftests/net: test nexthop without gw
+  * ip/nexthop: fix default address selection for connected nexthop
+    (LP: #1988809) // icmp_redirect.sh in ubuntu_kernel_selftests failed on
+    Jammy 5.15.0-49.55 (LP: #1990124)
+    - ip: fix triggering of 'icmp redirect'
+
+  [ Ubuntu: 5.15.0-49.55 ]
+
+  * jammy/linux: 5.15.0-49.55 -proposed tracker (LP: #1989785)
+  * amdgpu module crash after 5.15 kernel update (LP: #1981883)
+    - drm/amdgpu: fix check in fbdev init
+  * scsi: hisi_sas: Increase debugfs_dump_index after dump is  completed
+    (LP: #1982070)
+    - scsi: hisi_sas: Increase debugfs_dump_index after dump is completed
+  * [UBUNTU 22.04] s390/qeth: cache link_info for ethtool (LP: #1984103)
+    - s390/qeth: cache link_info for ethtool
+  * WARN in trace_event_dyn_put_ref (LP: #1987232)
+    - tracing/perf: Fix double put of trace event when init fails
+  * Jammy update: v5.15.60 upstream stable release (LP: #1989221)
+    - x86/speculation: Make all RETbleed mitigations 64-bit only
+    - selftests/bpf: Extend verifier and bpf_sock tests for dst_port loads
+    - selftests/bpf: Check dst_port only on the client socket
+    - block: fix default IO priority handling again
+    - tools/vm/slabinfo: Handle files in debugfs
+    - ACPI: video: Force backlight native for some TongFang devices
+    - ACPI: video: Shortening quirk list by identifying Clevo by board_name only
+    - ACPI: APEI: Better fix to avoid spamming the console with old error logs
+    - crypto: arm64/poly1305 - fix a read out-of-bound
+    - KVM: x86: do not report a vCPU as preempted outside instruction boundaries
+    - KVM: x86: do not set st->preempted when going back to user space
+    - KVM: selftests: Make hyperv_clock selftest more stable
+    - tools/kvm_stat: fix display of error when multiple processes are found
+    - selftests: KVM: Handle compiler optimizations in ucall
+    - KVM: x86/svm: add __GFP_ACCOUNT to __sev_dbg_{en,de}crypt_user()
+    - arm64: set UXN on swapper page tables
+    - btrfs: zoned: prevent allocation from previous data relocation BG
+    - btrfs: zoned: fix critical section of relocation inode writeback
+    - Bluetooth: hci_bcm: Add BCM4349B1 variant
+    - Bluetooth: hci_bcm: Add DT compatible for CYW55572
+    - dt-bindings: bluetooth: broadcom: Add BCM4349B1 DT binding
+    - Bluetooth: btusb: Add support of IMC Networks PID 0x3568
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04CA:0x4007
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04C5:0x1675
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0CB8:0xC558
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3587
+    - Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3586
+    - macintosh/adb: fix oob read in do_adb_query() function
+    - x86/speculation: Add RSB VM Exit protections
+    - x86/speculation: Add LFENCE to RSB fill sequence
+    - Linux 5.15.60
+  * Jammy update: v5.15.59 upstream stable release (LP: #1989218)
+    - Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
+    - Revert "ocfs2: mount shared volume without ha stack"
+    - ntfs: fix use-after-free in ntfs_ucsncmp()
+    - fs: sendfile handles O_NONBLOCK of out_fd
+    - secretmem: fix unhandled fault in truncate
+    - mm: fix page leak with multiple threads mapping the same page
+    - hugetlb: fix memoryleak in hugetlb_mcopy_atomic_pte
+    - asm-generic: remove a broken and needless ifdef conditional
+    - s390/archrandom: prevent CPACF trng invocations in interrupt context
+    - nouveau/svm: Fix to migrate all requested pages
+    - drm/simpledrm: Fix return type of simpledrm_simple_display_pipe_mode_valid()
+    - watch_queue: Fix missing rcu annotation
+    - watch_queue: Fix missing locking in add_watch_to_object()
+    - tcp: Fix data-races around sysctl_tcp_dsack.
+    - tcp: Fix a data-race around sysctl_tcp_app_win.
+    - tcp: Fix a data-race around sysctl_tcp_adv_win_scale.
+    - tcp: Fix a data-race around sysctl_tcp_frto.
+    - tcp: Fix a data-race around sysctl_tcp_nometrics_save.
+    - tcp: Fix data-races around sysctl_tcp_no_ssthresh_metrics_save.
+    - ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
+    - ice: do not setup vlan for loopback VSI
+    - scsi: ufs: host: Hold reference returned by of_parse_phandle()
+    - Revert "tcp: change pingpong threshold to 3"
+    - octeontx2-pf: Fix UDP/TCP src and dst port tc filters
+    - tcp: Fix data-races around sysctl_tcp_moderate_rcvbuf.
+    - tcp: Fix a data-race around sysctl_tcp_limit_output_bytes.
+    - tcp: Fix a data-race around sysctl_tcp_challenge_ack_limit.
+    - scsi: core: Fix warning in scsi_alloc_sgtables()
+    - scsi: mpt3sas: Stop fw fault watchdog work item during system shutdown
+    - net: ping6: Fix memleak in ipv6_renew_options().
+    - ipv6/addrconf: fix a null-ptr-deref bug for ip6_ptr
+    - net/tls: Remove the context from the list in tls_device_down
+    - igmp: Fix data-races around sysctl_igmp_qrv.
+    - net: pcs: xpcs: propagate xpcs_read error to xpcs_get_state_c37_sgmii
+    - net: sungem_phy: Add of_node_put() for reference returned by of_get_parent()
+    - tcp: Fix a data-race around sysctl_tcp_min_tso_segs.
+    - tcp: Fix a data-race around sysctl_tcp_min_rtt_wlen.
+    - tcp: Fix a data-race around sysctl_tcp_autocorking.
+    - tcp: Fix a data-race around sysctl_tcp_invalid_ratelimit.
+    - Documentation: fix sctp_wmem in ip-sysctl.rst
+    - macsec: fix NULL deref in macsec_add_rxsa
+    - macsec: fix error message in macsec_add_rxsa and _txsa
+    - macsec: limit replay window size with XPN
+    - macsec: always read MACSEC_SA_ATTR_PN as a u64
+    - net: macsec: fix potential resource leak in macsec_add_rxsa() and
+      macsec_add_txsa()
+    - net: mld: fix reference count leak in mld_{query | report}_work()
+    - tcp: Fix data-races around sk_pacing_rate.
+    - net: Fix data-races around sysctl_[rw]mem(_offset)?.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_delay_ns.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_slack_ns.
+    - tcp: Fix a data-race around sysctl_tcp_comp_sack_nr.
+    - tcp: Fix data-races around sysctl_tcp_reflect_tos.
+    - ipv4: Fix data-races around sysctl_fib_notify_on_flag_change.
+    - i40e: Fix interface init with MSI interrupts (no MSI-X)
+    - sctp: fix sleep in atomic context bug in timer handlers
+    - octeontx2-pf: cn10k: Fix egress ratelimit configuration
+    - virtio-net: fix the race between refill work and close
+    - perf symbol: Correct address for bss symbols
+    - sfc: disable softirqs for ptp TX
+    - sctp: leave the err path free in sctp_stream_init to sctp_stream_free
+    - ARM: crypto: comment out gcc warning that breaks clang builds
+    - mm/hmm: fault non-owner device private entries
+    - page_alloc: fix invalid watermark check on a negative value
+    - ARM: 9216/1: Fix MAX_DMA_ADDRESS overflow
+    - EDAC/ghes: Set the DIMM label unconditionally
+    - docs/kernel-parameters: Update descriptions for "mitigations=" param with
+      retbleed
+    - locking/rwsem: Allow slowpath writer to ignore handoff bit if not set by
+      first waiter
+    - x86/bugs: Do not enable IBPB at firmware entry when IBPB is not available
+    - Linux 5.15.59
+  * Jammy update: v5.15.58 upstream stable release (LP: #1988479)
+    - pinctrl: stm32: fix optional IRQ support to gpios
+    - riscv: add as-options for modules with assembly compontents
+    - mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
+    - lockdown: Fix kexec lockdown bypass with ima policy
+    - drm/ttm: fix locking in vmap/vunmap TTM GEM helpers
+    - bus: mhi: host: pci_generic: add Telit FN980 v1 hardware revision
+    - bus: mhi: host: pci_generic: add Telit FN990
+    - Revert "selftest/vm: verify remap destination address in mremap_test"
+    - Revert "selftest/vm: verify mmap addr in mremap_test"
+    - PCI: hv: Fix multi-MSI to allow more than one MSI vector
+    - PCI: hv: Fix hv_arch_irq_unmask() for multi-MSI
+    - PCI: hv: Reuse existing IRTE allocation in compose_msi_msg()
+    - PCI: hv: Fix interrupt mapping for multi-MSI
+    - serial: mvebu-uart: correctly report configured baudrate value
+    - batman-adv: Use netif_rx_any_context() any.
+    - xfs: fix maxlevels comparisons in the btree staging code
+    - xfs: fold perag loop iteration logic into helper function
+    - xfs: rename the next_agno perag iteration variable
+    - xfs: terminate perag iteration reliably on agcount
+    - xfs: fix perag reference leak on iteration race with growfs
+    - xfs: prevent a WARN_ONCE() in xfs_ioc_attr_list()
+    - r8152: fix a WOL issue
+    - ip: Fix data-races around sysctl_ip_default_ttl.
+    - xfrm: xfrm_policy: fix a possible double xfrm_pols_put() in
+      xfrm_bundle_lookup()
+    - power/reset: arm-versatile: Fix refcount leak in versatile_reboot_probe
+    - RDMA/irdma: Do not advertise 1GB page size for x722
+    - RDMA/irdma: Fix sleep from invalid context BUG
+    - pinctrl: ralink: rename MT7628(an) functions to MT76X8
+    - pinctrl: ralink: rename pinctrl-rt2880 to pinctrl-ralink
+    - pinctrl: ralink: Check for null return of devm_kcalloc
+    - perf/core: Fix data race between perf_event_set_output() and
+      perf_mmap_close()
+    - ipv4/tcp: do not use per netns ctl sockets
+    - net: tun: split run_ebpf_filter() and pskb_trim() into different "if
+      statement"
+    - mm/pagealloc: sysctl: change watermark_scale_factor max limit to 30%
+    - sysctl: move some boundary constants from sysctl.c to sysctl_vals
+    - tcp: Fix data-races around sysctl_tcp_ecn.
+    - drm/amd/display: Add option to defer works of hpd_rx_irq
+    - drm/amd/display: Fork thread to offload work of hpd_rx_irq
+    - drm/amdgpu/display: add quirk handling for stutter mode
+    - drm/amd/display: Ignore First MST Sideband Message Return Error
+    - scsi: megaraid: Clear READ queue map's nr_queues
+    - scsi: ufs: core: Drop loglevel of WriteBoost message
+    - nvme: check for duplicate identifiers earlier
+    - nvme: fix block device naming collision
+    - igc: Reinstate IGC_REMOVED logic and implement it properly
+    - ip: Fix data-races around sysctl_ip_no_pmtu_disc.
+    - ip: Fix data-races around sysctl_ip_fwd_use_pmtu.
+    - ip: Fix data-races around sysctl_ip_fwd_update_priority.
+    - ip: Fix data-races around sysctl_ip_nonlocal_bind.
+    - ip: Fix a data-race around sysctl_ip_autobind_reuse.
+    - ip: Fix a data-race around sysctl_fwmark_reflect.
+    - tcp/dccp: Fix a data-race around sysctl_tcp_fwmark_accept.
+    - tcp: sk->sk_bound_dev_if once in inet_request_bound_dev_if()
+    - tcp: Fix data-races around sysctl_tcp_l3mdev_accept.
+    - tcp: Fix data-races around sysctl_tcp_mtu_probing.
+    - tcp: Fix data-races around sysctl_tcp_base_mss.
+    - tcp: Fix data-races around sysctl_tcp_min_snd_mss.
+    - tcp: Fix a data-race around sysctl_tcp_mtu_probe_floor.
+    - tcp: Fix a data-race around sysctl_tcp_probe_threshold.
+    - tcp: Fix a data-race around sysctl_tcp_probe_interval.
+    - net: stmmac: fix pm runtime issue in stmmac_dvr_remove()
+    - net: stmmac: fix unbalanced ptp clock issue in suspend/resume flow
+    - mtd: rawnand: gpmi: validate controller clock rate
+    - mtd: rawnand: gpmi: Set WAIT_FOR_READY timeout based on program/erase times
+    - net: dsa: microchip: ksz_common: Fix refcount leak bug
+    - net: skb: introduce kfree_skb_reason()
+    - net: skb: use kfree_skb_reason() in tcp_v4_rcv()
+    - net: skb: use kfree_skb_reason() in __udp4_lib_rcv()
+    - net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
+    - net: skb_drop_reason: add document for drop reasons
+    - net: netfilter: use kfree_drop_reason() for NF_DROP
+    - net: ipv4: use kfree_skb_reason() in ip_rcv_core()
+    - net: ipv4: use kfree_skb_reason() in ip_rcv_finish_core()
+    - i2c: mlxcpld: Fix register setting for 400KHz frequency
+    - i2c: cadence: Change large transfer count reset logic to be unconditional
+    - perf tests: Fix Convert perf time to TSC test for hybrid
+    - net: stmmac: fix dma queue left shift overflow issue
+    - net/tls: Fix race in TLS device down flow
+    - igmp: Fix data-races around sysctl_igmp_llm_reports.
+    - igmp: Fix a data-race around sysctl_igmp_max_memberships.
+    - igmp: Fix data-races around sysctl_igmp_max_msf.
+    - tcp: Fix data-races around keepalive sysctl knobs.
+    - tcp: Fix data-races around sysctl_tcp_syn(ack)?_retries.
+    - tcp: Fix data-races around sysctl_tcp_syncookies.
+    - tcp: Fix data-races around sysctl_tcp_migrate_req.
+    - tcp: Fix data-races around sysctl_tcp_reordering.
+    - tcp: Fix data-races around some timeout sysctl knobs.
+    - tcp: Fix a data-race around sysctl_tcp_notsent_lowat.
+    - tcp: Fix a data-race around sysctl_tcp_tw_reuse.
+    - tcp: Fix data-races around sysctl_max_syn_backlog.
+    - tcp: Fix data-races around sysctl_tcp_fastopen.
+    - tcp: Fix data-races around sysctl_tcp_fastopen_blackhole_timeout.
+    - iavf: Fix handling of dummy receive descriptors
+    - pinctrl: armada-37xx: Use temporary variable for struct device
+    - pinctrl: armada-37xx: Make use of the devm_platform_ioremap_resource()
+    - pinctrl: armada-37xx: Convert to use dev_err_probe()
+    - pinctrl: armada-37xx: use raw spinlocks for regmap to avoid invalid wait
+      context
+    - i40e: Fix erroneous adapter reinitialization during recovery process
+    - ixgbe: Add locking to prevent panic when setting sriov_numvfs to zero
+    - net: stmmac: remove redunctant disable xPCS EEE call
+    - gpio: pca953x: only use single read/write for No AI mode
+    - gpio: pca953x: use the correct range when do regmap sync
+    - gpio: pca953x: use the correct register address when regcache sync during
+      init
+    - be2net: Fix buffer overflow in be_get_module_eeprom
+    - net: dsa: sja1105: silent spi_device_id warnings
+    - net: dsa: vitesse-vsc73xx: silent spi_device_id warnings
+    - drm/imx/dcss: Add missing of_node_put() in fail path
+    - ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh.
+    - ipv4: Fix data-races around sysctl_fib_multipath_hash_policy.
+    - ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
+    - ip: Fix data-races around sysctl_ip_prot_sock.
+    - udp: Fix a data-race around sysctl_udp_l3mdev_accept.
+    - tcp: Fix data-races around sysctl knobs related to SYN option.
+    - tcp: Fix a data-race around sysctl_tcp_early_retrans.
+    - tcp: Fix data-races around sysctl_tcp_recovery.
+    - tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
+    - tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
+    - tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
+    - tcp: Fix a data-race around sysctl_tcp_stdurg.
+    - tcp: Fix a data-race around sysctl_tcp_rfc1337.
+    - tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
+    - tcp: Fix data-races around sysctl_tcp_max_reordering.
+    - gpio: gpio-xilinx: Fix integer overflow
+    - KVM: selftests: Fix target thread to be migrated in rseq_test
+    - spi: bcm2835: bcm2835_spi_handle_err(): fix NULL pointer deref for non DMA
+      transfers
+    - KVM: Don't null dereference ops->destroy
+    - mm/mempolicy: fix uninit-value in mpol_rebind_policy()
+    - bpf: Make sure mac_header was set before using it
+    - sched/deadline: Fix BUG_ON condition for deboosted tasks
+    - x86/bugs: Warn when "ibrs" mitigation is selected on Enhanced IBRS parts
+    - dlm: fix pending remove if msg allocation fails
+    - x86/uaccess: Implement macros for CMPXCHG on user addresses
+    - bitfield.h: Fix "type of reg too small for mask" test
+    - x86/entry_32: Remove .fixup usage
+    - x86/extable: Extend extable functionality
+    - x86/msr: Remove .fixup usage
+    - x86/futex: Remove .fixup usage
+    - KVM: x86: Use __try_cmpxchg_user() to emulate atomic accesses
+    - xhci: dbc: refactor xhci_dbc_init()
+    - xhci: dbc: create and remove dbc structure in dbgtty driver.
+    - xhci: dbc: Rename xhci_dbc_init and xhci_dbc_exit
+    - xhci: Set HCD flag to defer primary roothub registration
+    - mt76: fix use-after-free by removing a non-RCU wcid pointer
+    - iwlwifi: fw: uefi: add missing include guards
+    - crypto: qat - set to zero DH parameters before free
+    - crypto: qat - use pre-allocated buffers in datapath
+    - crypto: qat - refactor submission logic
+    - crypto: qat - add backlog mechanism
+    - crypto: qat - fix memory leak in RSA
+    - crypto: qat - remove dma_free_coherent() for RSA
+    - crypto: qat - remove dma_free_coherent() for DH
+    - crypto: qat - add param check for RSA
+    - crypto: qat - add param check for DH
+    - crypto: qat - re-enable registration of algorithms
+    - exfat: fix referencing wrong parent directory information after renaming
+    - tracing: Have event format check not flag %p* on __get_dynamic_array()
+    - tracing: Place trace_pid_list logic into abstract functions
+    - tracing: Fix return value of trace_pid_write()
+    - um: virtio_uml: Allow probing from devicetree
+    - um: virtio_uml: Fix broken device handling in time-travel
+    - Bluetooth: Add bt_skb_sendmsg helper
+    - Bluetooth: Add bt_skb_sendmmsg helper
+    - Bluetooth: SCO: Replace use of memcpy_from_msg with bt_skb_sendmsg
+    - Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg
+    - Bluetooth: Fix passing NULL to PTR_ERR
+    - Bluetooth: SCO: Fix sco_send_frame returning skb->len
+    - Bluetooth: Fix bt_skb_sendmmsg not allocating partial chunks
+    - exfat: use updated exfat_chain directly during renaming
+    - x86/amd: Use IBPB for firmware calls
+    - x86/alternative: Report missing return thunk details
+    - watchqueue: make sure to serialize 'wqueue->defunct' properly
+    - tty: drivers/tty/, stop using tty_schedule_flip()
+    - tty: the rest, stop using tty_schedule_flip()
+    - tty: drop tty_schedule_flip()
+    - tty: extract tty_flip_buffer_commit() from tty_flip_buffer_push()
+    - tty: use new tty_insert_flip_string_and_push_buffer() in pty_write()
+    - watch-queue: remove spurious double semicolon
+    - drm/amd/display: invalid parameter check in dmub_hpd_callback
+    - x86/extable: Prefer local labels in .set directives
+    - KVM: x86: fix typo in __try_cmpxchg_user causing non-atomicness
+    - x86: drop bogus "cc" clobber from __try_cmpxchg_user_asm()
+    - drm/amdgpu: Off by one in dm_dmub_outbox1_low_irq()
+    - x86/entry_32: Fix segment exceptions
+    - Linux 5.15.58
+  * Jammy update: v5.15.57 upstream stable release (LP: #1988353)
+    - x86/xen: Fix initialisation in hypercall_page after rethunk
+    - tools arch x86: Sync the msr-index.h copy with the kernel sources
+    - tools headers cpufeatures: Sync with the kernel sources
+    - um: Add missing apply_returns()
+    - x86: Use -mindirect-branch-cs-prefix for RETPOLINE builds
+    - Linux 5.15.57
+  * Jammy update: v5.15.56 upstream stable release (LP: #1988351)
+    - ALSA: hda - Add fixup for Dell Latitidue E5430
+    - ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
+    - ALSA: hda/realtek: Fix headset mic for Acer SF313-51
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
+    - ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
+    - xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
+    - fix race between exit_itimers() and /proc/pid/timers
+    - mm: userfaultfd: fix UFFDIO_CONTINUE on fallocated shmem pages
+    - mm: split huge PUD on wp_huge_pud fallback
+    - tracing/histograms: Fix memory leak problem
+    - net: sock: tracing: Fix sock_exceed_buf_limit not to dereference stale
+      pointer
+    - ip: fix dflt addr selection for connected nexthop
+    - ARM: 9213/1: Print message about disabled Spectre workarounds only once
+    - ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
+    - wifi: mac80211: fix queue selection for mesh/OCB interfaces
+    - cgroup: Use separate src/dst nodes when preloading css_sets for migration
+    - btrfs: return -EAGAIN for NOWAIT dio reads/writes on compressed and inline
+      extents
+    - drm/panfrost: Put mapping instead of shmem obj on
+      panfrost_mmu_map_fault_addr() error
+    - drm/panfrost: Fix shrinker list corruption by madvise IOCTL
+    - fs/remap: constrain dedupe of EOF blocks
+    - nilfs2: fix incorrect masking of permission flags for symlinks
+    - sh: convert nommu io{re,un}map() to static inline functions
+    - Revert "evm: Fix memleak in init_desc"
+    - xfs: only run COW extent recovery when there are no live extents
+    - xfs: don't include bnobt blocks when reserving free block pool
+    - xfs: run callbacks before waking waiters in xlog_state_shutdown_callbacks
+    - xfs: drop async cache flushes from CIL commits.
+    - reset: Fix devm bulk optional exclusive control getter
+    - ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
+    - spi: amd: Limit max transfer and message size
+    - ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
+    - ARM: 9210/1: Mark the FDT_FIXED sections as shareable
+    - net/mlx5e: kTLS, Fix build time constant test in TX
+    - net/mlx5e: kTLS, Fix build time constant test in RX
+    - net/mlx5e: Fix enabling sriov while tc nic rules are offloaded
+    - net/mlx5e: Fix capability check for updating vnic env counters
+    - net/mlx5e: Ring the TX doorbell on DMA errors
+    - drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
+    - ima: Fix a potential integer overflow in ima_appraise_measurement
+    - ASoC: sgtl5000: Fix noise on shutdown/remove
+    - ASoC: tas2764: Add post reset delays
+    - ASoC: tas2764: Fix and extend FSYNC polarity handling
+    - ASoC: tas2764: Correct playback volume range
+    - ASoC: tas2764: Fix amp gain register offset & default
+    - ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
+    - ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
+    - net: stmmac: dwc-qos: Disable split header for Tegra194
+    - net: ethernet: ti: am65-cpsw: Fix devlink port register sequence
+    - sysctl: Fix data races in proc_dointvec().
+    - sysctl: Fix data races in proc_douintvec().
+    - sysctl: Fix data races in proc_dointvec_minmax().
+    - sysctl: Fix data races in proc_douintvec_minmax().
+    - sysctl: Fix data races in proc_doulongvec_minmax().
+    - sysctl: Fix data races in proc_dointvec_jiffies().
+    - tcp: Fix a data-race around sysctl_tcp_max_orphans.
+    - inetpeer: Fix data-races around sysctl.
+    - net: Fix data-races around sysctl_mem.
+    - cipso: Fix data-races around sysctl.
+    - icmp: Fix data-races around sysctl.
+    - ipv4: Fix a data-race around sysctl_fib_sync_mem.
+    - ARM: dts: at91: sama5d2: Fix typo in i2s1 node
+    - ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
+    - arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
+    - arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
+    - netfilter: nf_log: incorrect offset to network header
+    - netfilter: nf_tables: replace BUG_ON by element length check
+    - drm/i915/gvt: IS_ERR() vs NULL bug in intel_gvt_update_reg_whitelist()
+    - xen/gntdev: Ignore failure to unmap INVALID_GRANT_HANDLE
+    - lockd: set fl_owner when unlocking files
+    - lockd: fix nlm_close_files
+    - tracing: Fix sleeping while atomic in kdb ftdump
+    - drm/i915/selftests: fix a couple IS_ERR() vs NULL tests
+    - drm/i915/dg2: Add Wa_22011100796
+    - drm/i915/gt: Serialize GRDOM access between multiple engine resets
+    - drm/i915/gt: Serialize TLB invalidates with GT resets
+    - drm/i915/uc: correctly track uc_fw init failure
+    - drm/i915: Require the vm mutex for i915_vma_bind()
+    - bnxt_en: Fix bnxt_reinit_after_abort() code path
+    - bnxt_en: Fix bnxt_refclk_read()
+    - sysctl: Fix data-races in proc_dou8vec_minmax().
+    - sysctl: Fix data-races in proc_dointvec_ms_jiffies().
+    - icmp: Fix data-races around sysctl_icmp_echo_enable_probe.
+    - icmp: Fix a data-race around sysctl_icmp_ignore_bogus_error_responses.
+    - icmp: Fix a data-race around sysctl_icmp_errors_use_inbound_ifaddr.
+    - icmp: Fix a data-race around sysctl_icmp_ratelimit.
+    - icmp: Fix a data-race around sysctl_icmp_ratemask.
+    - raw: Fix a data-race around sysctl_raw_l3mdev_accept.
+    - tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
+    - ipv4: Fix data-races around sysctl_ip_dynaddr.
+    - nexthop: Fix data-races around nexthop_compat_mode.
+    - net: ftgmac100: Hold reference returned by of_get_child_by_name()
+    - net: stmmac: fix leaks in probe
+    - ima: force signature verification when CONFIG_KEXEC_SIG is configured
+    - ima: Fix potential memory leak in ima_init_crypto()
+    - drm/amd/display: Only use depth 36 bpp linebuffers on DCN display engines.
+    - drm/amd/pm: Prevent divide by zero
+    - sfc: fix use after free when disabling sriov
+    - ceph: switch netfs read ops to use rreq->inode instead of
+      rreq->mapping->host
+    - seg6: fix skb checksum evaluation in SRH encapsulation/insertion
+    - seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
+    - seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
+    - sfc: fix kernel panic when creating VF
+    - KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
+    - net/tls: Check for errors in tls_device_init
+    - ACPI: video: Fix acpi_video_handles_brightness_key_presses()
+    - mm: sysctl: fix missing numa_stat when !CONFIG_HUGETLB_PAGE
+    - btrfs: rename btrfs_bio to btrfs_io_context
+    - btrfs: zoned: fix a leaked bioc in read_zone_info
+    - ksmbd: use SOCK_NONBLOCK type for kernel_accept()
+    - powerpc/xive/spapr: correct bitmap allocation size
+    - vdpa/mlx5: Initialize CVQ vringh only once
+    - vduse: Tie vduse mgmtdev and its device
+    - virtio_mmio: Add missing PM calls to freeze/restore
+    - virtio_mmio: Restore guest page size on resume
+    - netfilter: br_netfilter: do not skip all hooks with 0 priority
+    - scsi: hisi_sas: Limit max hw sectors for v3 HW
+    - cpufreq: pmac32-cpufreq: Fix refcount leak bug
+    - firmware: sysfb: Make sysfb_create_simplefb() return a pdev pointer
+    - firmware: sysfb: Add sysfb_disable() helper function
+    - fbdev: Disable sysfb device registration when removing conflicting FBs
+    - net: tipc: fix possible refcount leak in tipc_sk_create()
+    - NFC: nxp-nci: don't print header length mismatch on i2c error
+    - nvme-tcp: always fail a request when sending it failed
+    - nvme: fix regression when disconnect a recovering ctrl
+    - net: sfp: fix memory leak in sfp_probe()
+    - ASoC: ops: Fix off by one in range control validation
+    - pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux()
+    - ASoC: Realtek/Maxim SoundWire codecs: disable pm_runtime on remove
+    - ASoC: rt711-sdca-sdw: fix calibrate mutex initialization
+    - ASoC: Intel: sof_sdw: handle errors on card registration
+    - ASoC: rt711: fix calibrate mutex initialization
+    - ASoC: rt7*-sdw: harden jack_detect_handler
+    - ASoC: codecs: rt700/rt711/rt711-sdca: initialize workqueues in probe
+    - ASoC: SOF: Intel: hda-loader: Clarify the cl_dsp_init() flow
+    - ASoC: wcd938x: Fix event generation for some controls
+    - ASoC: Intel: bytcr_wm5102: Fix GPIO related probe-ordering problem
+    - ASoC: wm5110: Fix DRE control
+    - ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error
+    - ASoC: dapm: Initialise kcontrol data for mux/demux controls
+    - ASoC: cs47l15: Fix event generation for low power mux control
+    - ASoC: madera: Fix event generation for OUT1 demux
+    - ASoC: madera: Fix event generation for rate controls
+    - irqchip: or1k-pic: Undefine mask_ack for level triggered hardware
+    - x86: Clear .brk area at early boot
+    - soc: ixp4xx/npe: Fix unused match warning
+    - ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
+    - Revert "can: xilinx_can: Limit CANFD brp to 2"
+    - ALSA: usb-audio: Add quirks for MacroSilicon MS2100/MS2106 devices
+    - ALSA: usb-audio: Add quirk for Fiero SC-01
+    - ALSA: usb-audio: Add quirk for Fiero SC-01 (fw v1.0.0)
+    - nvme-pci: phison e16 has bogus namespace ids
+    - signal handling: don't use BUG_ON() for debugging
+    - USB: serial: ftdi_sio: add Belimo device ids
+    - usb: typec: add missing uevent when partner support PD
+    - usb: dwc3: gadget: Fix event pending check
+    - tty: serial: samsung_tty: set dma burst_size to 1
+    - vt: fix memory overlapping when deleting chars in the buffer
+    - serial: 8250: fix return error code in serial8250_request_std_resource()
+    - serial: stm32: Clear prev values before setting RTS delays
+    - serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle
+    - serial: 8250: Fix PM usage_count for console handover
+    - x86/pat: Fix x86_has_pat_wp()
+    - drm/aperture: Run fbdev removal before internal helpers
+    - Linux 5.15.56
+  * Jammy update: v5.15.55 upstream stable release (LP: #1988338)
+    - Linux 5.15.55
+  * Jammy update: v5.15.54 upstream stable release (LP: #1987451)
+    - mm/slub: add missing TID updates on slab deactivation
+    - mm/filemap: fix UAF in find_lock_entries
+    - Revert "selftests/bpf: Add test for bpf_timer overwriting crash"
+    - ALSA: usb-audio: Workarounds for Behringer UMC 204/404 HD
+    - ALSA: hda/realtek: Add quirk for Clevo L140PU
+    - ALSA: cs46xx: Fix missing snd_card_free() call at probe error
+    - can: bcm: use call_rcu() instead of costly synchronize_rcu()
+    - can: grcan: grcan_probe(): remove extra of_node_get()
+    - can: gs_usb: gs_usb_open/close(): fix memory leak
+    - can: m_can: m_can_chip_config(): actually enable internal timestamping
+    - can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32
+      bits
+    - can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for
+      mcp2517fd
+    - can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on
+      TBC register
+    - bpf: Fix incorrect verifier simulation around jmp32's jeq/jne
+    - bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
+    - usbnet: fix memory leak in error case
+    - net: rose: fix UAF bug caused by rose_t0timer_expiry
+    - netfilter: nft_set_pipapo: release elements in clone from abort path
+    - btrfs: rename btrfs_alloc_chunk to btrfs_create_chunk
+    - btrfs: add additional parameters to btrfs_init_tree_ref/btrfs_init_data_ref
+    - btrfs: fix invalid delayed ref after subvolume creation failure
+    - btrfs: fix warning when freeing leaf after subvolume creation failure
+    - Input: cpcap-pwrbutton - handle errors from platform_get_irq()
+    - Input: goodix - change goodix_i2c_write() len parameter type to int
+    - Input: goodix - add a goodix.h header file
+    - Input: goodix - refactor reset handling
+    - Input: goodix - try not to touch the reset-pin on x86/ACPI devices
+    - dma-buf/poll: Get a file reference for outstanding fence callbacks
+    - btrfs: fix deadlock between chunk allocation and chunk btree modifications
+    - drm/i915: Disable bonding on gen12+ platforms
+    - drm/i915/gt: Register the migrate contexts with their engines
+    - drm/i915: Replace the unconditional clflush with drm_clflush_virt_range()
+    - media: ir_toy: prevent device from hanging during transmit
+    - memory: renesas-rpc-if: Avoid unaligned bus access for HyperFlash
+    - ath11k: add hw_param for wakeup_mhi
+    - qed: Improve the stack space of filter_config()
+    - platform/x86: wmi: introduce helper to convert driver to WMI driver
+    - platform/x86: wmi: Replace read_takes_no_args with a flags field
+    - platform/x86: wmi: Fix driver->notify() vs ->probe() race
+    - mt76: mt7921: get rid of mt7921_mac_set_beacon_filter
+    - mt76: mt7921: introduce mt7921_mcu_set_beacon_filter utility routine
+    - mt76: mt7921: fix a possible race enabling/disabling runtime-pm
+    - bpf: Stop caching subprog index in the bpf_pseudo_func insn
+    - bpf, arm64: Use emit_addr_mov_i64() for BPF_PSEUDO_FUNC
+    - riscv: defconfig: enable DRM_NOUVEAU
+    - RISC-V: defconfigs: Set CONFIG_FB=y, for FB console
+    - net/mlx5e: Check action fwd/drop flag exists also for nic flows
+    - net/mlx5e: Split actions_match_supported() into a sub function
+    - net/mlx5e: TC, Reject rules with drop and modify hdr action
+    - net/mlx5e: TC, Reject rules with forward and drop actions
+    - ASoC: rt5682: Avoid the unexpected IRQ event during going to suspend
+    - ASoC: rt5682: Re-detect the combo jack after resuming
+    - ASoC: rt5682: Fix deadlock on resume
+    - netfilter: nf_tables: convert pktinfo->tprot_set to flags field
+    - netfilter: nft_payload: support for inner header matching / mangling
+    - netfilter: nft_payload: don't allow th access for fragments
+    - s390/boot: allocate amode31 section in decompressor
+    - s390/setup: use physical pointers for memblock_reserve()
+    - s390/setup: preserve memory at OLDMEM_BASE and OLDMEM_SIZE
+    - ibmvnic: init init_done_rc earlier
+    - ibmvnic: clear fop when retrying probe
+    - ibmvnic: Allow queueing resets during probe
+    - virtio-blk: avoid preallocating big SGL for data
+    - io_uring: ensure that fsnotify is always called
+    - block: use bdev_get_queue() in bio.c
+    - block: only mark bio as tracked if it really is tracked
+    - block: fix rq-qos breakage from skipping rq_qos_done_bio()
+    - stddef: Introduce struct_group() helper macro
+    - media: omap3isp: Use struct_group() for memcpy() region
+    - media: davinci: vpif: fix use-after-free on driver unbind
+    - mt76: mt76_connac: fix MCU_CE_CMD_SET_ROC definition error
+    - mt76: mt7921: do not always disable fw runtime-pm
+    - cxl/port: Hold port reference until decoder release
+    - clk: renesas: r9a07g044: Update multiplier and divider values for PLL2/3
+    - KVM: x86/mmu: Use yield-safe TDP MMU root iter in MMU notifier unmapping
+    - KVM: x86/mmu: Use common TDP MMU zap helper for MMU notifier unmap hook
+    - scsi: qla2xxx: Move heartbeat handling from DPC thread to workqueue
+    - scsi: qla2xxx: Fix laggy FC remote port session recovery
+    - scsi: qla2xxx: edif: Replace list_for_each_safe with
+      list_for_each_entry_safe
+    - scsi: qla2xxx: Fix crash during module load unload test
+    - gfs2: Fix gfs2_file_buffered_write endless loop workaround
+    - vdpa/mlx5: Avoid processing works if workqueue was destroyed
+    - btrfs: handle device lookup with btrfs_dev_lookup_args
+    - btrfs: add a btrfs_get_dev_args_from_path helper
+    - btrfs: use btrfs_get_dev_args_from_path in dev removal ioctls
+    - btrfs: remove device item and update super block in the same transaction
+    - drbd: add error handling support for add_disk()
+    - drbd: Fix double free problem in drbd_create_device
+    - drbd: fix an invalid memory access caused by incorrect use of list iterator
+    - drm/amd/display: Set min dcfclk if pipe count is 0
+    - drm/amd/display: Fix by adding FPU protection for dcn30_internal_validate_bw
+    - NFSD: De-duplicate net_generic(nf->nf_net, nfsd_net_id)
+    - NFSD: COMMIT operations must not return NFS?ERR_INVAL
+    - riscv/mm: Add XIP_FIXUP for riscv_pfn_base
+    - iio: accel: mma8452: use the correct logic to get mma8452_data
+    - batman-adv: Use netif_rx().
+    - mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
+    - Compiler Attributes: add __alloc_size() for better bounds checking
+    - mm: vmalloc: introduce array allocation functions
+    - KVM: use __vcalloc for very large allocations
+    - btrfs: don't access possibly stale fs_info data in device_list_add
+    - KVM: s390x: fix SCK locking
+    - scsi: qla2xxx: Fix loss of NVMe namespaces after driver reload test
+    - powerpc/32: Don't use lmw/stmw for saving/restoring non volatile regs
+    - powerpc: flexible GPR range save/restore macros
+    - powerpc/tm: Fix more userspace r13 corruption
+    - serial: sc16is7xx: Clear RS485 bits in the shutdown
+    - bus: mhi: core: Use correctly sized arguments for bit field
+    - bus: mhi: Fix pm_state conversion to string
+    - stddef: Introduce DECLARE_FLEX_ARRAY() helper
+    - uapi/linux/stddef.h: Add include guards
+    - ASoC: rt5682: move clk related code to rt5682_i2c_probe
+    - ASoC: rt5682: fix an incorrect NULL check on list iterator
+    - drm/amd/vcn: fix an error msg on vcn 3.0
+    - KVM: Don't create VM debugfs files outside of the VM directory
+    - tty: n_gsm: Modify CR,PF bit when config requester
+    - tty: n_gsm: Save dlci address open status when config requester
+    - tty: n_gsm: fix frame reception handling
+    - ALSA: usb-audio: add mapping for MSI MPG X570S Carbon Max Wifi.
+    - ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.
+    - tty: n_gsm: fix missing update of modem controls after DLCI open
+    - btrfs: zoned: encapsulate inode locking for zoned relocation
+    - btrfs: zoned: use dedicated lock for data relocation
+    - KVM: Initialize debugfs_dentry when a VM is created to avoid NULL deref
+    - mm/hwpoison: mf_mutex for soft offline and unpoison
+    - mm/hwpoison: avoid the impact of hwpoison_filter() return value on mce
+      handler
+    - mm/memory-failure.c: fix race with changing page compound again
+    - mm/hwpoison: fix race between hugetlb free/demotion and
+      memory_failure_hugetlb()
+    - tty: n_gsm: fix invalid use of MSC in advanced option
+    - tty: n_gsm: fix sometimes uninitialized warning in gsm_dlci_modem_output()
+    - serial: 8250_mtk: Make sure to select the right FEATURE_SEL
+    - tty: n_gsm: fix invalid gsmtty_write_room() result
+    - drm/i915: Fix a race between vma / object destruction and unbinding
+    - drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb
+    - drm/mediatek: Remove the pointer of struct cmdq_client
+    - drm/mediatek: Detect CMDQ execution timeout
+    - drm/mediatek: Add cmdq_handle in mtk_crtc
+    - drm/mediatek: Add vblank register/unregister callback functions
+    - Bluetooth: protect le accept and resolv lists with hdev->lock
+    - Bluetooth: btmtksdio: fix use-after-free at btmtksdio_recv_event
+    - io_uring: avoid io-wq -EAGAIN looping for !IOPOLL
+    - irqchip/gic-v3: Ensure pseudo-NMIs have an ISB between ack and handling
+    - irqchip/gic-v3: Refactor ISB + EOIR at ack time
+    - rxrpc: Fix locking issue
+    - dt-bindings: soc: qcom: smd-rpm: Add compatible for MSM8953 SoC
+    - dt-bindings: soc: qcom: smd-rpm: Fix missing MSM8936 compatible
+    - module: change to print useful messages from elf_validity_check()
+    - module: fix [e_shstrndx].sh_size=0 OOB access
+    - iommu/vt-d: Fix PCI bus rescan device hot add
+    - fbdev: fbmem: Fix logo center image dx issue
+    - PM: runtime: Redefine pm_runtime_release_supplier()
+    - memregion: Fix memregion_free() fallback definition
+    - video: of_display_timing.h: include errno.h
+    - powerpc/powernv: delay rng platform device creation until later in boot
+    - net: dsa: qca8k: reset cpu port on MTU change
+    - can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
+    - can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
+    - can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
+    - xfs: remove incorrect ASSERT in xfs_rename
+    - Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown"
+    - btrfs: fix error pointer dereference in btrfs_ioctl_rm_dev_v2()
+    - virtio-blk: modify the value type of num in virtio_queue_rq()
+    - btrfs: fix use of uninitialized variable at rm device ioctl
+    - tty: n_gsm: fix encoding of command/response bit
+    - ARM: meson: Fix refcount leak in meson_smp_prepare_cpus
+    - pinctrl: sunxi: a83t: Fix NAND function name for some pins
+    - ASoC: rt711: Add endianness flag in snd_soc_component_driver
+    - ASoC: rt711-sdca: Add endianness flag in snd_soc_component_driver
+    - ASoC: codecs: rt700/rt711/rt711-sdca: resume bus/codec in .set_jack_detect
+    - arm64: dts: qcom: msm8994: Fix CPU6/7 reg values
+    - arm64: dts: qcom: sdm845: use dispcc AHB clock for mdss node
+    - ARM: mxs_defconfig: Enable the framebuffer
+    - arm64: dts: imx8mp-evk: correct mmc pad settings
+    - arm64: dts: imx8mp-evk: correct the uart2 pinctl value
+    - arm64: dts: imx8mp-evk: correct gpio-led pad settings
+    - arm64: dts: imx8mp-evk: correct vbus pad settings
+    - arm64: dts: imx8mp-evk: correct eqos pad settings
+    - arm64: dts: imx8mp-evk: correct I2C1 pad settings
+    - arm64: dts: imx8mp-evk: correct I2C3 pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct uart pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct eqos pad settings
+    - arm64: dts: imx8mp-phyboard-pollux-rdk: correct i2c2 & mmc settings
+    - pinctrl: sunxi: sunxi_pconf_set: use correct offset
+    - arm64: dts: qcom: msm8992-*: Fix vdd_lvs1_2-supply typo
+    - ARM: at91: pm: use proper compatible for sama5d2's rtc
+    - ARM: at91: pm: use proper compatibles for sam9x60's rtc and rtt
+    - ARM: at91: pm: use proper compatibles for sama7g5's rtc and rtt
+    - ARM: dts: at91: sam9x60ek: fix eeprom compatible and size
+    - ARM: dts: at91: sama5d2_icp: fix eeprom compatibles
+    - ARM: at91: fix soc detection for SAM9X60 SiPs
+    - xsk: Clear page contiguity bit when unmapping pool
+    - i2c: piix4: Fix a memory leak in the EFCH MMIO support
+    - i40e: Fix dropped jumbo frames statistics
+    - i40e: Fix VF's MAC Address change on VM
+    - ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
+    - ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
+    - ibmvnic: Properly dispose of all skbs during a failover.
+    - selftests: forwarding: fix flood_unicast_test when h2 supports
+      IFF_UNICAST_FLT
+    - selftests: forwarding: fix learning_test when h1 supports IFF_UNICAST_FLT
+    - selftests: forwarding: fix error message in learning_test
+    - r8169: fix accessing unset transport header
+    - i2c: cadence: Unregister the clk notifier in error path
+    - dmaengine: imx-sdma: Allow imx8m for imx7 FW revs
+    - misc: rtsx_usb: fix use of dma mapped buffer for usb bulk transfer
+    - misc: rtsx_usb: use separate command and response buffers
+    - misc: rtsx_usb: set return value in rsp_buf alloc err path
+    - Revert "mm/memory-failure.c: fix race with changing page compound again"
+    - Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
+    - dt-bindings: dma: allwinner,sun50i-a64-dma: Fix min/max typo
+    - ida: don't use BUG_ON() for debugging
+    - dmaengine: pl330: Fix lockdep warning about non-static key
+    - dmaengine: lgm: Fix an error handling path in intel_ldma_probe()
+    - dmaengine: at_xdma: handle errors of at_xdmac_alloc_desc() correctly
+    - dmaengine: ti: Fix refcount leak in ti_dra7_xbar_route_allocate
+    - dmaengine: qcom: bam_dma: fix runtime PM underflow
+    - dmaengine: ti: Add missing put_device in ti_dra7_xbar_route_allocate
+    - dmaengine: idxd: force wq context cleanup on device disable path
+    - selftests/net: fix section name when using xdp_dummy.o
+    - Linux 5.15.54
+
+  [ Ubuntu: 5.15.0-48.54 ]
+
+  * jammy/linux: 5.15.0-48.54 -proposed tracker (LP: #1987775)
+  * System freeze after resuming from suspend due to PCI ASPM settings
+    (LP: #1980829)
+    - SAUCE: PCI/ASPM: Save/restore L1SS Capability for suspend/resume
+    - SAUCE: whitelist platforms that needs save/restore ASPM L1SS for
+      suspend/resume
+  * [SRU][J/OEM-5.17][PATCH 0/1] Fix oled brightness set above frame-average
+    luminance (LP: #1978986)
+    - SAUCE: drm: New function to get luminance range based on static hdr metadata
+    - SAUCE: drm/amdgpu_dm: Rely on split out luminance calculation function
+    - SAUCE: drm/i915: Use luminance range calculated during edid parsing
+  * Jammy: Add OVS Internal Port HW Offload to mlx5 driver (LP: #1983498)
+    - net/mlx5e: Refactor rx handler of represetor device
+    - net/mlx5e: Use generic name for the forwarding dev pointer
+    - net/mlx5: E-Switch, Add ovs internal port mapping to metadata support
+    - net/mlx5e: Support accept action
+    - net/mlx5e: Accept action skbedit in the tc actions list
+    - net/mlx5e: Offload tc rules that redirect to ovs internal port
+    - net/mlx5e: Offload internal port as encap route device
+    - net/mlx5e: Enable TC offload for ingress MACVLAN
+    - net/mlx5e: Add indirect tc offload of ovs internal port
+    - net/mlx5e: Term table handling of internal port rules
+    - net/mlx5: Support internal port as decap route device
+    - net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'
+    - net/mlx5e: TC, Fix memory leak with rules with internal port
+    - net/mlx5e: Fix skb memory leak when TC classifier action offloads are
+      disabled
+    - net/mlx5e: Fix nullptr on deleting mirroring rule
+    - net/mlx5e: Avoid implicit modify hdr for decap drop rule
+    - net/mlx5e: Fix wrong source vport matching on tunnel rule
+    - net/mlx5e: TC, fix decap fallback to uplink when int port not supported
+  * Remove unused variable from i915 psr (LP: #1986798)
+    - SAUCE: drm/i915/display/psr: Remove unused variable
+  * refactoring of overlayfs fix to properly support shiftfs (LP: #1983640)
+    - SAUCE: overlayfs: remove CONFIG_AUFS_FS dependency
+  * Jammy update: v5.15.53 upstream stable release (LP: #1986728)
+    - Revert "drm/amdgpu/display: set vblank_disable_immediate for DC"
+    - drm/amdgpu: To flush tlb for MMHUB of RAVEN series
+    - ksmbd: set the range of bytes to zero without extending file size in
+      FSCTL_ZERO_DATA
+    - ksmbd: check invalid FileOffset and BeyondFinalZero in FSCTL_ZERO_DATA
+    - ksmbd: use vfs_llseek instead of dereferencing NULL
+    - ipv6: take care of disable_policy when restoring routes
+    - net: phy: Don't trigger state machine while in suspend
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG SX6000LNP (AKA SPECTRIX
+      S40G)
+    - nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA IM2P33F8ABR1
+    - nvdimm: Fix badblocks clear off-by-one error
+    - powerpc/prom_init: Fix kernel config grep
+    - powerpc/book3e: Fix PUD allocation size in map_kernel_page()
+    - powerpc/bpf: Fix use of user_pt_regs in uapi
+    - dm raid: fix accesses beyond end of raid member array
+    - dm raid: fix KASAN warning in raid5_add_disks
+    - s390/archrandom: simplify back to earlier design and initialize earlier
+    - SUNRPC: Fix READ_PLUS crasher
+    - net: rose: fix UAF bugs caused by timer handler
+    - net: usb: ax88179_178a: Fix packet receiving
+    - virtio-net: fix race between ndo_open() and virtio_device_ready()
+    - selftests/net: pass ipv6_args to udpgso_bench's IPv6 TCP test
+    - net: dsa: bcm_sf2: force pause link settings
+    - net: tun: unlink NAPI from device on destruction
+    - net: tun: stop NAPI when detaching queues
+    - net: dp83822: disable false carrier interrupt
+    - net: dp83822: disable rx error interrupt
+    - RDMA/qedr: Fix reporting QP timeout attribute
+    - RDMA/cm: Fix memory leak in ib_cm_insert_listen
+    - linux/dim: Fix divide by 0 in RDMA DIM
+    - net: usb: asix: do not force pause frames support
+    - usbnet: fix memory allocation in helpers
+    - selftests: mptcp: more stable diag tests
+    - net: ipv6: unexport __init-annotated seg6_hmac_net_init()
+    - NFSD: restore EINVAL error translation in nfsd_commit()
+    - vfs: fix copy_file_range() regression in cross-fs copies
+    - caif_virtio: fix race between virtio_device_ready() and ndo_open()
+    - PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
+    - vdpa/mlx5: Update Control VQ callback information
+    - s390: remove unneeded 'select BUILD_BIN2C'
+    - netfilter: nft_dynset: restore set element counter when failing to update
+    - net/dsa/hirschmann: Add missing of_node_get() in hellcreek_led_setup()
+    - net/sched: act_api: Notify user space if any actions were flushed before
+      error
+    - net: asix: fix "can't send until first packet is send" issue
+    - net: bonding: fix possible NULL deref in rlb code
+    - net: phy: ax88772a: fix lost pause advertisement configuration
+    - net: bonding: fix use-after-free after 802.3ad slave unbind
+    - powerpc/memhotplug: Add add_pages override for PPC
+    - nfc: nfcmrvl: Fix irq_of_parse_and_map() return value
+    - NFC: nxp-nci: Don't issue a zero length i2c_master_read()
+    - tipc: move bc link creation back to tipc_node_create
+    - epic100: fix use after free on rmmod
+    - io_uring: ensure that send/sendmsg and recv/recvmsg check sqe->ioprio
+    - ACPI: video: Change how we determine if brightness key-presses are handled
+    - tunnels: do not assume mac header is set in skb_tunnel_check_pmtu()
+    - ipv6/sit: fix ipip6_tunnel_get_prl return value
+    - ipv6: fix lockdep splat in in6_dump_addrs()
+    - mlxsw: spectrum_router: Fix rollback in tunnel next hop init
+    - net: tun: avoid disabling NAPI twice
+    - MAINTAINERS: add Leah as xfs maintainer for 5.15.y
+    - tcp: add a missing nf_reset_ct() in 3WHS handling
+    - selftests/bpf: Add test_verifier support to fixup kfunc call insns
+    - selftests/rseq: remove ARRAY_SIZE define from individual tests
+    - selftests/rseq: introduce own copy of rseq uapi header
+    - selftests/rseq: Remove useless assignment to cpu variable
+    - selftests/rseq: Remove volatile from __rseq_abi
+    - selftests/rseq: Introduce rseq_get_abi() helper
+    - selftests/rseq: Introduce thread pointer getters
+    - selftests/rseq: Uplift rseq selftests for compatibility with glibc-2.35
+    - selftests/rseq: Fix ppc32: wrong rseq_cs 32-bit field pointer on big endian
+    - selftests/rseq: Fix ppc32 missing instruction selection "u" and "x" for
+      load/store
+    - selftests/rseq: Fix ppc32 offsets by using long rather than off_t
+    - selftests/rseq: Fix warnings about #if checks of undefined tokens
+    - selftests/rseq: Remove arm/mips asm goto compiler work-around
+    - selftests/rseq: Fix: work-around asm goto compiler bugs
+    - selftests/rseq: x86-64: use %fs segment selector for accessing rseq thread
+      area
+    - selftests/rseq: x86-32: use %gs segment selector for accessing rseq thread
+      area
+    - selftests/rseq: Change type of rseq_offset to ptrdiff_t
+    - xen/blkfront: fix leaking data in shared pages
+    - xen/netfront: fix leaking data in shared pages
+    - xen/netfront: force data bouncing when backend is untrusted
+    - xen/blkfront: force data bouncing when backend is untrusted
+    - xen-netfront: restore __skb_queue_tail() positioning in
+      xennet_get_responses()
+    - xen/arm: Fix race in RB-tree based P2M accounting
+    - net: usb: qmi_wwan: add Telit 0x1070 composition
+    - clocksource/drivers/ixp4xx: remove EXPORT_SYMBOL_GPL from
+      ixp4xx_timer_setup()
+    - fsi: occ: Force sequence numbering per OCC
+    - net: fix IFF_TX_SKB_NO_LINEAR definition
+    - drm/i915/gem: add missing else
+    - drm/msm/gem: Fix error return on fence id alloc fail
+    - drivers: cpufreq: Add missing of_node_put() in qoriq-cpufreq.c
+    - platform/x86: panasonic-laptop: de-obfuscate button codes
+    - platform/x86: panasonic-laptop: sort includes alphabetically
+    - platform/x86: panasonic-laptop: revert "Resolve hotkey double trigger bug"
+    - platform/x86: panasonic-laptop: don't report duplicate brightness key-
+      presses
+    - platform/x86: panasonic-laptop: filter out duplicate volume up/down/mute
+      keypresses
+    - drm/fourcc: fix integer type usage in uapi header
+    - hwmon: (occ) Remove sequence numbering and checksum calculation
+    - hwmon: (occ) Prevent power cap command overwriting poll response
+    - hwmon: (ibmaem) don't call platform_device_del() if platform_device_add()
+      fails
+    - Linux 5.15.53
+  * Jammy update: v5.15.52 upstream stable release (LP: #1986724)
+    - tick/nohz: unexport __init-annotated tick_nohz_full_setup()
+    - xfs: use kmem_cache_free() for kmem_cache objects
+    - xfs: punch out data fork delalloc blocks on COW writeback failure
+    - xfs: Fix the free logic of state in xfs_attr_node_hasname
+    - xfs: remove all COW fork extents when remounting readonly
+    - xfs: check sb_meta_uuid for dabuf buffer recovery
+    - xfs: prevent UAF in xfs_log_item_in_current_chkpt
+    - xfs: only bother with sync_filesystem during readonly remount
+    - powerpc/ftrace: Remove ftrace init tramp once kernel init is complete
+    - fs: add is_idmapped_mnt() helper
+    - fs: move mapping helpers
+    - fs: tweak fsuidgid_has_mapping()
+    - fs: account for filesystem mappings
+    - docs: update mapping documentation
+    - fs: use low-level mapping helpers
+    - fs: remove unused low-level mapping helpers
+    - fs: port higher-level mapping helpers
+    - fs: add i_user_ns() helper
+    - fs: support mapped mounts of mapped filesystems
+    - fs: fix acl translation
+    - fs: account for group membership
+    - rtw88: 8821c: support RFE type4 wifi NIC
+    - rtw88: rtw8821c: enable rfe 6 devices
+    - net: mscc: ocelot: allow unregistered IP multicast flooding to CPU
+    - io_uring: fix not locked access to fixed buf table
+    - Linux 5.15.52
+  * Jammy update: v5.15.51 upstream stable release (LP: #1986718)
+    - random: schedule mix_interrupt_randomness() less often
+    - random: quiet urandom warning ratelimit suppression message
+    - ALSA: hda/via: Fix missing beep setup
+    - ALSA: hda/conexant: Fix missing beep setup
+    - ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop
+    - ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
+    - ALSA: hda/realtek: Add quirk for Clevo PD70PNT
+    - ALSA: hda/realtek: Add quirk for Clevo NS50PU
+    - net: openvswitch: fix parsing of nw_proto for IPv6 fragments
+    - 9p: Fix refcounting during full path walks for fid lookups
+    - 9p: fix fid refcount leak in v9fs_vfs_atomic_open_dotl
+    - 9p: fix fid refcount leak in v9fs_vfs_get_link
+    - btrfs: fix hang during unmount when block group reclaim task is running
+    - btrfs: prevent remounting to v1 space cache for subpage mount
+    - btrfs: add error messages to all unrecognized mount options
+    - scsi: ibmvfc: Store vhost pointer during subcrq allocation
+    - scsi: ibmvfc: Allocate/free queue resource only during probe/remove
+    - mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing
+    - mmc: mediatek: wait dma stop bit reset to 0
+    - xen/gntdev: Avoid blocking in unmap_grant_pages()
+    - MAINTAINERS: Add new IOMMU development mailing list
+    - ata: libata: add qc->flags in ata_qc_complete_template tracepoint
+    - dm era: commit metadata in postsuspend after worker stops
+    - dm mirror log: clear log bits up to BITS_PER_LONG boundary
+    - tracing/kprobes: Check whether get_kretprobe() returns NULL in
+      kretprobe_dispatcher()
+    - drm/i915: Implement w/a 22010492432 for adl-s
+    - USB: serial: pl2303: add support for more HXN (G) types
+    - USB: serial: option: add Telit LE910Cx 0x1250 composition
+    - USB: serial: option: add Quectel EM05-G modem
+    - USB: serial: option: add Quectel RM500K module support
+    - drm/msm: Ensure mmap offset is initialized
+    - drm/msm: Fix double pm_runtime_disable() call
+    - netfilter: use get_random_u32 instead of prandom
+    - scsi: scsi_debug: Fix zone transition to full condition
+    - drm/msm: Switch ordering of runpm put vs devfreq_idle
+    - scsi: iscsi: Exclude zero from the endpoint ID range
+    - xsk: Fix generic transmit when completion queue reservation fails
+    - drm/msm: use for_each_sgtable_sg to iterate over scatterlist
+    - bpf: Fix request_sock leak in sk lookup helpers
+    - drm/sun4i: Fix crash during suspend after component bind failure
+    - bpf, x86: Fix tail call count offset calculation on bpf2bpf call
+    - scsi: storvsc: Correct reporting of Hyper-V I/O size limits
+    - phy: aquantia: Fix AN when higher speeds than 1G are not advertised
+    - KVM: arm64: Prevent kmemleak from accessing pKVM memory
+    - net: Write lock dev_base_lock without disabling bottom halves.
+    - net: fix data-race in dev_isalive()
+    - tipc: fix use-after-free Read in tipc_named_reinit
+    - igb: fix a use-after-free issue in igb_clean_tx_ring
+    - bonding: ARP monitor spams NETDEV_NOTIFY_PEERS notifiers
+    - ethtool: Fix get module eeprom fallback
+    - net/sched: sch_netem: Fix arithmetic in netem_dump() for 32-bit platforms
+    - drm/msm/mdp4: Fix refcount leak in mdp4_modeset_init_intf
+    - drm/msm/dp: check core_initialized before disable interrupts at
+      dp_display_unbind()
+    - drm/msm/dp: Drop now unused hpd_high member
+    - drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read failed
+    - drm/msm/dp: do not initialize phy until plugin interrupt received
+    - drm/msm/dp: force link training for display resolution change
+    - perf arm-spe: Don't set data source if it's not a memory operation
+    - erspan: do not assume transport header is always set
+    - net/tls: fix tls_sk_proto_close executed repeatedly
+    - udmabuf: add back sanity check
+    - selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
+    - xen-blkfront: Handle NULL gendisk
+    - x86/xen: Remove undefined behavior in setup_features()
+    - MIPS: Remove repetitive increase irq_err_count
+    - afs: Fix dynamic root getattr
+    - ice: ethtool: advertise 1000M speeds properly
+    - regmap-irq: Fix a bug in regmap_irq_enable() for type_in_mask chips
+    - regmap-irq: Fix offset/index mismatch in read_sub_irq_data()
+    - virtio_net: fix xdp_rxq_info bug after suspend/resume
+    - Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
+    - sock: redo the psock vs ULP protection check
+    - nvme-pci: add NO APST quirk for Kioxia device
+    - nvme: move the Samsung X5 quirk entry to the core quirks
+    - gpio: winbond: Fix error code in winbond_gpio_get()
+    - s390/cpumf: Handle events cycles and instructions identical
+    - iio: mma8452: fix probe fail when device tree compatible is used.
+    - iio: magnetometer: yas530: Fix memchr_inv() misuse
+    - iio: adc: vf610: fix conversion mode sysfs node name
+    - usb: typec: wcove: Drop wrong dependency to INTEL_SOC_PMIC
+    - xhci-pci: Allow host runtime PM as default for Intel Raptor Lake xHCI
+    - xhci-pci: Allow host runtime PM as default for Intel Meteor Lake xHCI
+    - usb: gadget: Fix non-unique driver names in raw-gadget driver
+    - USB: gadget: Fix double-free bug in raw_gadget driver
+    - usb: chipidea: udc: check request status before setting device address
+    - dt-bindings: usb: ohci: Increase the number of PHYs
+    - dt-bindings: usb: ehci: Increase the number of PHYs
+    - btrfs: don't set lock_owner when locking extent buffer for reading
+    - btrfs: fix deadlock with fsync+fiemap+transaction commit
+    - f2fs: attach inline_data after setting compression
+    - iio:humidity:hts221: rearrange iio trigger get and register
+    - iio:chemical:ccs811: rearrange iio trigger get and register
+    - iio:accel:kxcjk-1013: rearrange iio trigger get and register
+    - iio:accel:bma180: rearrange iio trigger get and register
+    - iio:accel:mxc4005: rearrange iio trigger get and register
+    - iio: accel: mma8452: ignore the return value of reset operation
+    - iio: gyro: mpu3050: Fix the error handling in mpu3050_power_up()
+    - iio: trigger: sysfs: fix use-after-free on remove
+    - iio: adc: stm32: fix maximum clock rate for stm32mp15x
+    - iio: imu: inv_icm42600: Fix broken icm42600 (chip id 0 value)
+    - iio: afe: rescale: Fix boolean logic bug
+    - iio: adc: stm32: Fix ADCs iteration in irq handler
+    - iio: adc: stm32: Fix IRQs on STM32F4 by removing custom spurious IRQs
+      message
+    - iio: adc: axp288: Override TS pin bias current for some models
+    - iio: adc: rzg2l_adc: add missing fwnode_handle_put() in
+      rzg2l_adc_parse_properties()
+    - iio: adc: adi-axi-adc: Fix refcount leak in adi_axi_adc_attach_client
+    - iio: adc: ti-ads131e08: add missing fwnode_handle_put() in
+      ads131e08_alloc_channels()
+    - xtensa: xtfpga: Fix refcount leak bug in setup
+    - xtensa: Fix refcount leak bug in time.c
+    - parisc/stifb: Fix fb_is_primary_device() only available with CONFIG_FB_STI
+    - parisc: Enable ARCH_HAS_STRICT_MODULE_RWX
+    - powerpc/microwatt: wire up rng during setup_arch()
+    - powerpc: Enable execve syscall exit tracepoint
+    - powerpc/rtas: Allow ibm,platform-dump RTAS call with null buffer address
+    - powerpc/powernv: wire up rng during setup_arch
+    - drm/msm/dp: Always clear mask bits to disable interrupts at
+      dp_ctrl_reset_irq_ctrl()
+    - ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node
+    - ARM: dts: imx6qdl: correct PU regulator ramp delay
+    - arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode
+    - ARM: exynos: Fix refcount leak in exynos_map_pmu
+    - soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe
+    - ARM: Fix refcount leak in axxia_boot_secondary
+    - memory: samsung: exynos5422-dmc: Fix refcount leak in of_get_dram_timings
+    - ARM: cns3xxx: Fix refcount leak in cns3xxx_init
+    - modpost: fix section mismatch check for exported init/exit sections
+    - ARM: dts: bcm2711-rpi-400: Fix GPIO line names
+    - random: update comment from copy_to_user() -> copy_to_iter()
+    - perf build-id: Fix caching files with a wrong build ID
+    - dma-direct: use the correct size for dma_set_encrypted()
+    - kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS (2nd attempt)
+    - powerpc/pseries: wire up rng during setup_arch()
+    - Linux 5.15.51
+  * Jammy update: v5.15.50 upstream stable release (LP: #1986715)
+    - net: mana: Add handling of CQE_RX_TRUNCATED
+    - zonefs: fix zonefs_iomap_begin() for reads
+    - usb: gadget: u_ether: fix regression in setting fixed MAC address
+    - bpf: Fix calling global functions from BPF_PROG_TYPE_EXT programs
+    - selftests/bpf: Add selftest for calling global functions from freplace
+    - serial: core: Initialize rs485 RTS polarity already on probe
+    - arm64: mm: Don't invalidate FROM_DEVICE buffers at start of DMA transfer
+    - Linux 5.15.50
+  * Jammy update: v5.15.49 upstream stable release (LP: #1983149)
+    - Revert "drm/amd/display: Fix DCN3 B0 DP Alt Mapping"
+    - nfsd: Replace use of rwsem with errseq_t
+    - arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3
+    - arm64: dts: imx8mn-beacon: Enable RTS-CTS on UART3
+    - powerpc/kasan: Silence KASAN warnings in __get_wchan()
+    - ASoC: nau8822: Add operation for internal PLL off and on
+    - drm/amd/display: Read Golden Settings Table from VBIOS
+    - drm/amdkfd: Use mmget_not_zero in MMU notifier
+    - dma-debug: make things less spammy under memory pressure
+    - ASoC: cs42l52: Fix TLV scales for mixer controls
+    - ASoC: cs35l36: Update digital volume TLV
+    - ASoC: cs53l30: Correct number of volume levels on SX controls
+    - ASoC: cs42l52: Correct TLV for Bypass Volume
+    - ASoC: cs42l56: Correct typo in minimum level for SX volume controls
+    - ASoC: cs42l51: Correct minimum value for SX volume control
+    - drm/amdkfd: add pinned BOs to kfd_bo_list
+    - ata: libata-core: fix NULL pointer deref in ata_host_alloc_pinfo()
+    - quota: Prevent memory allocation recursion while holding dq_lock
+    - ASoC: wm8962: Fix suspend while playing music
+    - ASoC: es8328: Fix event generation for deemphasis control
+    - ASoC: wm_adsp: Fix event generation for wm_adsp_fw_put()
+    - Input: soc_button_array - also add Lenovo Yoga Tablet2 1051F to
+      dmi_use_low_level_irq
+    - scsi: vmw_pvscsi: Expand vcpuHint to 16 bits
+    - scsi: lpfc: Resolve NULL ptr dereference after an ELS LOGO is aborted
+    - scsi: lpfc: Fix port stuck in bypassed state after LIP in PT2PT topology
+    - scsi: lpfc: Allow reduced polling rate for nvme_admin_async_event cmd
+      completion
+    - scsi: mpt3sas: Fix out-of-bounds compiler warning
+    - scsi: ipr: Fix missing/incorrect resource cleanup in error case
+    - scsi: pmcraid: Fix missing resource cleanup in error case
+    - ALSA: hda/realtek - Add HW8326 support
+    - virtio-mmio: fix missing put_device() when vm_cmdline_parent registration
+      failed
+    - nfc: nfcmrvl: Fix memory leak in nfcmrvl_play_deferred
+    - ipv6: Fix signed integer overflow in l2tp_ip6_sendmsg
+    - net: ethernet: mtk_eth_soc: fix misuse of mem alloc interface
+      netdev[napi]_alloc_frag
+    - gcc-12: disable '-Wdangling-pointer' warning for now
+    - mellanox: mlx5: avoid uninitialized variable warning with gcc-12
+    - MIPS: Loongson-3: fix compile mips cpu_hwmon as module build error.
+    - random: credit cpu and bootloader seeds by default
+    - gpio: dwapb: Don't print error on -EPROBE_DEFER
+    - platform/x86: gigabyte-wmi: Add Z690M AORUS ELITE AX DDR4 support
+    - platform/x86: gigabyte-wmi: Add support for B450M DS3H-CF
+    - platform/x86/intel: hid: Add Surface Go to VGBS allow list
+    - staging: r8188eu: fix rtw_alloc_hwxmits error detection for now
+    - staging: r8188eu: Use zeroing allocator in wpa_set_encryption()
+    - staging: r8188eu: Fix warning of array overflow in ioctl_linux.c
+    - pNFS: Don't keep retrying if the server replied NFS4ERR_LAYOUTUNAVAILABLE
+    - pNFS: Avoid a live lock condition in pnfs_update_layout()
+    - sunrpc: set cl_max_connect when cloning an rpc_clnt
+    - clocksource: hyper-v: unexport __init-annotated hv_init_clocksource()
+    - i40e: Fix adding ADQ filter to TC0
+    - i40e: Fix calculating the number of queue pairs
+    - i40e: Fix call trace in setup_tx_descriptors
+    - Drivers: hv: vmbus: Release cpu lock in error case
+    - tty: goldfish: Fix free_irq() on remove
+    - misc: atmel-ssc: Fix IRQ check in ssc_probe
+    - io_uring: fix races with file table unregister
+    - io_uring: fix races with buffer table unregister
+    - drm/i915/reset: Fix error_state_read ptr + offset use
+    - net: hns3: split function hclge_update_port_base_vlan_cfg()
+    - net: hns3: set port base vlan tbl_sta to false before removing old vlan
+    - net: hns3: don't push link state to VF if unalive
+    - net: hns3: fix tm port shapping of fibre port is incorrect after driver
+      initialization
+    - nvme: add device name to warning in uuid_show()
+    - mlxsw: spectrum_cnt: Reorder counter pools
+    - net: bgmac: Fix an erroneous kfree() in bgmac_remove()
+    - net: ax25: Fix deadlock caused by skb_recv_datagram in ax25_recvmsg
+    - arm64: ftrace: fix branch range checks
+    - arm64: ftrace: consistently handle PLTs.
+    - certs/blacklist_hashes.c: fix const confusion in certs blacklist
+    - init: Initialize noop_backing_dev_info early
+    - block: Fix handling of offline queues in blk_mq_alloc_request_hctx()
+    - faddr2line: Fix overlapping text section failures, the sequel
+    - i2c: npcm7xx: Add check for platform_driver_register
+    - irqchip/gic/realview: Fix refcount leak in realview_gic_of_init
+    - irqchip/gic-v3: Fix error handling in gic_populate_ppi_partitions
+    - irqchip/gic-v3: Fix refcount leak in gic_populate_ppi_partitions
+    - irqchip/realtek-rtl: Fix refcount leak in map_interrupts
+    - sched: Fix balance_push() vs __sched_setscheduler()
+    - i2c: designware: Use standard optional ref clock implementation
+    - mei: hbm: drop capability response on early shutdown
+    - mei: me: add raptor lake point S DID
+    - comedi: vmk80xx: fix expression for tx buffer size
+    - [Config] updateconfigs for LIB_MEMNEQ
+    - crypto: memneq - move into lib/
+    - USB: serial: option: add support for Cinterion MV31 with new baseline
+    - USB: serial: io_ti: add Agilent E5805A support
+    - usb: dwc2: Fix memory leak in dwc2_hcd_init
+    - usb: cdnsp: Fixed setting last_trb incorrectly
+    - usb: gadget: lpc32xx_udc: Fix refcount leak in lpc32xx_udc_probe
+    - usb: gadget: f_fs: change ep->status safe in ffs_epfile_io()
+    - usb: gadget: f_fs: change ep->ep safe in ffs_epfile_io()
+    - tty: n_gsm: Debug output allocation must use GFP_ATOMIC
+    - serial: 8250: Store to lsr_save_flags after lsr read
+    - bus: fsl-mc-bus: fix KASAN use-after-free in fsl_mc_bus_remove()
+    - dm mirror log: round up region bitmap size to BITS_PER_LONG
+    - drm/amd/display: Cap OLED brightness per max frame-average luminance
+    - cfi: Fix __cfi_slowpath_diag RCU usage with cpuidle
+    - ext4: fix super block checksum incorrect after mount
+    - ext4: fix bug_on ext4_mb_use_inode_pa
+    - ext4: make variable "count" signed
+    - ext4: add reserved GDT blocks check
+    - KVM: arm64: Don't read a HW interrupt pending state in user context
+    - virtio-pci: Remove wrong address verification in vp_del_vqs()
+    - powerpc/book3e: get rid of #include <generated/compile.h>
+    - clk: imx8mp: fix usb_root_clk parent
+    - Linux 5.15.49
+  * Jammy update: v5.15.48 upstream stable release (LP: #1983146)
+    - Linux 5.15.48
+    - Upstream stable to v5.15.48
+  * Jammy update: v5.15.47 upstream stable release (LP: #1982968)
+    - pcmcia: db1xxx_ss: restrict to MIPS_DB1XXX boards
+    - staging: greybus: codecs: fix type confusion of list iterator variable
+    - iio: adc: ad7124: Remove shift from scan_type
+    - lkdtm/bugs: Check for the NULL pointer after calling kmalloc
+    - lkdtm/bugs: Don't expect thread termination without CONFIG_UBSAN_TRAP
+    - tty: goldfish: Use tty_port_destroy() to destroy port
+    - tty: serial: owl: Fix missing clk_disable_unprepare() in owl_uart_probe
+    - tty: n_tty: Restore EOF push handling behavior
+    - serial: 8250_aspeed_vuart: Fix potential NULL dereference in
+      aspeed_vuart_probe
+    - tty: serial: fsl_lpuart: fix potential bug when using both of_alias_get_id
+      and ida_simple_get
+    - remoteproc: imx_rproc: Ignore create mem entry for resource table
+    - usb: usbip: fix a refcount leak in stub_probe()
+    - usb: usbip: add missing device lock on tweak configuration cmd
+    - USB: storage: karma: fix rio_karma_init return
+    - usb: musb: Fix missing of_node_put() in omap2430_probe
+    - staging: fieldbus: Fix the error handling path in
+      anybuss_host_common_probe()
+    - pwm: lp3943: Fix duty calculation in case period was clamped
+    - pwm: raspberrypi-poe: Fix endianness in firmware struct
+    - rpmsg: qcom_smd: Fix irq_of_parse_and_map() return value
+    - usb: dwc3: gadget: Replace list_for_each_entry_safe() if using giveback
+    - usb: dwc3: pci: Fix pm_runtime_get_sync() error checking
+    - misc: fastrpc: fix an incorrect NULL check on list iterator
+    - firmware: stratix10-svc: fix a missing check on list iterator
+    - usb: typec: mux: Check dev_set_name() return value
+    - rpmsg: virtio: Fix possible double free in rpmsg_probe()
+    - rpmsg: virtio: Fix possible double free in rpmsg_virtio_add_ctrl_dev()
+    - rpmsg: virtio: Fix the unregistration of the device rpmsg_ctrl
+    - iio: adc: stmpe-adc: Fix wait_for_completion_timeout return value check
+    - iio: proximity: vl53l0x: Fix return value check of
+      wait_for_completion_timeout
+    - iio: adc: sc27xx: fix read big scale voltage not right
+    - iio: adc: sc27xx: Fine tune the scale calibration values
+    - rpmsg: qcom_smd: Fix returning 0 if irq_of_parse_and_map() fails
+    - pvpanic: Fix typos in the comments
+    - misc/pvpanic: Convert regular spinlock into trylock on panic path
+    - phy: qcom-qmp: fix pipe-clock imbalance on power-on failure
+    - power: supply: axp288_fuel_gauge: Drop BIOS version check from "T3 MRD" DMI
+      quirk
+    - serial: sifive: Report actual baud base rather than fixed 115200
+    - export: fix string handling of namespace in EXPORT_SYMBOL_NS
+    - soundwire: intel: prevent pm_runtime resume prior to system suspend
+    - coresight: cpu-debug: Replace mutex with mutex_trylock on panic notifier
+    - ksmbd: fix reference count leak in smb_check_perm_dacl()
+    - extcon: ptn5150: Add queue work sync before driver release
+    - soc: rockchip: Fix refcount leak in rockchip_grf_init
+    - clocksource/drivers/riscv: Events are stopped during CPU suspend
+    - ARM: dts: aspeed: ast2600-evb: Enable RX delay for MAC0/MAC1
+    - rtc: mt6397: check return value after calling platform_get_resource()
+    - rtc: ftrtc010: Use platform_get_irq() to get the interrupt
+    - rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
+    - staging: r8188eu: add check for kzalloc
+    - tty: n_gsm: Don't ignore write return value in gsmld_output()
+    - tty: n_gsm: Fix packet data hex dump output
+    - serial: meson: acquire port->lock in startup()
+    - serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
+    - serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
+    - serial: digicolor-usart: Don't allow CS5-6
+    - serial: rda-uart: Don't allow CS5-6
+    - serial: txx9: Don't allow CS5-6
+    - serial: sh-sci: Don't allow CS5-6
+    - serial: sifive: Sanitize CSIZE and c_iflag
+    - serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
+    - serial: stm32-usart: Correct CSIZE, bits, and parity
+    - firmware: dmi-sysfs: Fix memory leak in dmi_sysfs_register_handle
+    - bus: ti-sysc: Fix warnings for unbind for serial
+    - driver: base: fix UAF when driver_attach failed
+    - driver core: fix deadlock in __device_attach
+    - watchdog: rti-wdt: Fix pm_runtime_get_sync() error checking
+    - watchdog: ts4800_wdt: Fix refcount leak in ts4800_wdt_probe
+    - blk-mq: don't touch ->tagset in blk_mq_get_sq_hctx
+    - ASoC: fsl_sai: Fix FSL_SAI_xDR/xFR definition
+    - clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
+    - s390/crypto: fix scatterwalk_unmap() callers in AES-GCM
+    - net: sched: fixed barrier to prevent skbuff sticking in qdisc backlog
+    - net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry()
+    - net: ethernet: ti: am65-cpsw-nuss: Fix some refcount leaks
+    - net: dsa: mv88e6xxx: Fix refcount leak in mv88e6xxx_mdios_register
+    - modpost: fix removing numeric suffixes
+    - jffs2: fix memory leak in jffs2_do_fill_super
+    - ubi: fastmap: Fix high cpu usage of ubi_bgt by making sure wl_pool not empty
+    - ubi: ubi_create_volume: Fix use-after-free when volume creation failed
+    - selftests/bpf: fix selftest after random: Urandom_read tracepoint removal
+    - selftests/bpf: fix stacktrace_build_id with missing kprobe/urandom_read
+    - bpf: Fix probe read error in ___bpf_prog_run()
+    - block: take destination bvec offsets into account in bio_copy_data_iter
+    - riscv: read-only pages should not be writable
+    - net/smc: fixes for converting from "struct smc_cdc_tx_pend **" to "struct
+      smc_wr_tx_pend_priv *"
+    - tcp: add accessors to read/set tp->snd_cwnd
+    - nfp: only report pause frame configuration for physical device
+    - sfc: fix considering that all channels have TX queues
+    - sfc: fix wrong tx channel offset with efx_separate_tx_channels
+    - block: make bioset_exit() fully resilient against being called twice
+    - vdpa: Fix error logic in vdpa_nl_cmd_dev_get_doit
+    - virtio: pci: Fix an error handling path in vp_modern_probe()
+    - net/mlx5: Don't use already freed action pointer
+    - net/mlx5: CT: Fix header-rewrite re-use for tupels
+    - net/mlx5: correct ECE offset in query qp output
+    - net/mlx5e: Update netdev features after changing XDP state
+    - net: sched: add barrier to fix packet stuck problem for lockless qdisc
+    - tcp: tcp_rtx_synack() can be called from process context
+    - vdpa: ifcvf: set pci driver data in probe
+    - octeontx2-af: fix error code in is_valid_offset()
+    - s390/mcck: isolate SIE instruction when setting CIF_MCCK_GUEST flag
+    - regulator: mt6315-regulator: fix invalid allowed mode
+    - gpio: pca953x: use the correct register address to do regcache sync
+    - afs: Fix infinite loop found by xfstest generic/676
+    - scsi: sd: Fix potential NULL pointer dereference
+    - tipc: check attribute length for bearer name
+    - driver core: Fix wait_for_device_probe() & deferred_probe_timeout
+      interaction
+    - perf c2c: Fix sorting in percent_rmt_hitm_cmp()
+    - dmaengine: idxd: set DMA_INTERRUPT cap bit
+    - mips: cpc: Fix refcount leak in mips_cpc_default_phys_base
+    - bootconfig: Make the bootconfig.o as a normal object file
+    - tracing: Make tp_printk work on syscall tracepoints
+    - tracing: Fix sleeping function called from invalid context on RT kernel
+    - tracing: Avoid adding tracer option before update_tracer_options
+    - iommu/arm-smmu: fix possible null-ptr-deref in arm_smmu_device_probe()
+    - iommu/arm-smmu-v3: check return value after calling platform_get_resource()
+    - f2fs: remove WARN_ON in f2fs_is_valid_blkaddr
+    - i2c: cadence: Increase timeout per message if necessary
+    - m68knommu: set ZERO_PAGE() to the allocated zeroed page
+    - m68knommu: fix undefined reference to `_init_sp'
+    - dmaengine: zynqmp_dma: In struct zynqmp_dma_chan fix desc_size data type
+    - NFSv4: Don't hold the layoutget locks across multiple RPC calls
+    - video: fbdev: hyperv_fb: Allow resolutions with size > 64 MB for Gen1
+    - video: fbdev: pxa3xx-gcu: release the resources correctly in
+      pxa3xx_gcu_probe/remove()
+    - RISC-V: use memcpy for kexec_file mode
+    - m68knommu: fix undefined reference to `mach_get_rtc_pll'
+    - f2fs: fix to tag gcing flag on page during file defragment
+    - xprtrdma: treat all calls not a bcall when bc_serv is NULL
+    - drm/bridge: sn65dsi83: Fix an error handling path in sn65dsi83_probe()
+    - drm/bridge: ti-sn65dsi83: Handle dsi_lanes == 0 as invalid
+    - netfilter: nat: really support inet nat without l3 address
+    - netfilter: nf_tables: use kfree_rcu(ptr, rcu) to release hooks in clean_net
+      path
+    - netfilter: nf_tables: delete flowtable hooks via transaction list
+    - powerpc/kasan: Force thread size increase with KASAN
+    - SUNRPC: Trap RDMA segment overflows
+    - netfilter: nf_tables: always initialize flowtable hook list in transaction
+    - ata: pata_octeon_cf: Fix refcount leak in octeon_cf_probe
+    - netfilter: nf_tables: release new hooks on unsupported flowtable flags
+    - netfilter: nf_tables: memleak flow rule from commit path
+    - netfilter: nf_tables: bail out early if hardware offload is not supported
+    - xen: unexport __init-annotated xen_xlate_map_ballooned_pages()
+    - stmmac: intel: Fix an error handling path in intel_eth_pci_probe()
+    - af_unix: Fix a data-race in unix_dgram_peer_wake_me().
+    - bpf, arm64: Clear prog->jited_len along prog->jited
+    - net: dsa: lantiq_gswip: Fix refcount leak in gswip_gphy_fw_list
+    - net/mlx4_en: Fix wrong return value on ioctl EEPROM query failure
+    - i40e: xsk: Move tmp desc array from driver to pool
+    - xsk: Fix handling of invalid descriptors in XSK TX batching API
+    - SUNRPC: Fix the calculation of xdr->end in xdr_get_next_encode_buffer()
+    - net: mdio: unexport __init-annotated mdio_bus_init()
+    - net: xfrm: unexport __init-annotated xfrm4_protocol_init()
+    - net: ipv6: unexport __init-annotated seg6_hmac_init()
+    - net/mlx5: Lag, filter non compatible devices
+    - net/mlx5: Fix mlx5_get_next_dev() peer device matching
+    - net/mlx5: Rearm the FW tracer after each tracer event
+    - net/mlx5: fs, fail conflicting actions
+    - ip_gre: test csum_start instead of transport header
+    - net: altera: Fix refcount leak in altera_tse_mdio_create
+    - net: dsa: mv88e6xxx: use BMSR_ANEGCOMPLETE bit for filling an_complete
+    - tcp: use alloc_large_system_hash() to allocate table_perturb
+    - drm: imx: fix compiler warning with gcc-12
+    - nfp: flower: restructure flow-key for gre+vlan combination
+    - iov_iter: Fix iter_xarray_get_pages{,_alloc}()
+    - iio: dummy: iio_simple_dummy: check the return value of kstrdup()
+    - staging: rtl8712: fix a potential memory leak in r871xu_drv_init()
+    - iio: st_sensors: Add a local lock for protecting odr
+    - lkdtm/usercopy: Expand size of "out of frame" object
+    - drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback()
+    - drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()
+    - tty: synclink_gt: Fix null-pointer-dereference in slgt_clean()
+    - tty: Fix a possible resource leak in icom_probe
+    - thunderbolt: Use different lane for second DisplayPort tunnel
+    - drivers: staging: rtl8192u: Fix deadlock in ieee80211_beacons_stop()
+    - drivers: staging: rtl8192e: Fix deadlock in rtllib_beacons_stop()
+    - USB: host: isp116x: check return value after calling platform_get_resource()
+    - drivers: tty: serial: Fix deadlock in sa1100_set_termios()
+    - drivers: usb: host: Fix deadlock in oxu_bus_suspend()
+    - USB: hcd-pci: Fully suspend across freeze/thaw cycle
+    - char: xillybus: fix a refcount leak in cleanup_dev()
+    - sysrq: do not omit current cpu when showing backtrace of all active CPUs
+    - usb: dwc2: gadget: don't reset gadget's driver->bus
+    - soundwire: qcom: adjust autoenumeration timeout
+    - misc: rtsx: set NULL intfdata when probe fails
+    - extcon: Fix extcon_get_extcon_dev() error handling
+    - extcon: Modify extcon device to be created after driver data is set
+    - clocksource/drivers/sp804: Avoid error on multiple instances
+    - staging: rtl8712: fix uninit-value in usb_read8() and friends
+    - staging: rtl8712: fix uninit-value in r871xu_drv_init()
+    - serial: msm_serial: disable interrupts in __msm_console_write()
+    - kernfs: Separate kernfs_pr_cont_buf and rename_lock.
+    - watchdog: wdat_wdt: Stop watchdog when rebooting the system
+    - md: protect md_unregister_thread from reentrancy
+    - scsi: myrb: Fix up null pointer access on myrb_cleanup()
+    - ceph: allow ceph.dir.rctime xattr to be updatable
+    - ceph: flush the mdlog for filesystem sync
+    - drm/amd/display: Check if modulo is 0 before dividing.
+    - drm/radeon: fix a possible null pointer dereference
+    - drm/amd/pm: Fix missing thermal throttler status
+    - um: line: Use separate IRQs per line
+    - modpost: fix undefined behavior of is_arm_mapping_symbol()
+    - x86/cpu: Elide KCSAN for cpu_has() and friends
+    - jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
+    - nbd: call genl_unregister_family() first in nbd_cleanup()
+    - nbd: fix race between nbd_alloc_config() and module removal
+    - cifs: version operations for smb20 unneeded when legacy support disabled
+    - drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
+    - nodemask: Fix return values to be unsigned
+    - vringh: Fix loop descriptors check in the indirect cases
+    - scripts/gdb: change kernel config dumping method
+    - ALSA: usb-audio: Skip generic sync EP parse for secondary EP
+    - ALSA: usb-audio: Set up (implicit) sync for Saffire 6
+    - ALSA: hda/conexant - Fix loopback issue with CX20632
+    - ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo Yoga
+      DuetITL 2021
+    - ALSA: hda/realtek: Add quirk for HP Dev One
+    - cifs: return errors during session setup during reconnects
+    - cifs: fix reconnect on smb3 mount types
+    - KEYS: trusted: tpm2: Fix migratable logic
+    - ata: libata-transport: fix {dma|pio|xfer}_mode sysfs files
+    - mmc: block: Fix CQE recovery reset success
+    - net: phy: dp83867: retrigger SGMII AN when link change
+    - writeback: Fix inode->i_io_list not be protected by inode->i_lock error
+    - nfc: st21nfca: fix incorrect validating logic in EVT_TRANSACTION
+    - nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
+    - nfc: st21nfca: fix incorrect sizing calculations in EVT_TRANSACTION
+    - ixgbe: fix bcast packets Rx on VF after promisc removal
+    - ixgbe: fix unexpected VLAN Rx in promisc mode on VF
+    - Input: bcm5974 - set missing URB_NO_TRANSFER_DMA_MAP urb flag
+    - vduse: Fix NULL pointer dereference on sysfs access
+    - powerpc: Don't select HAVE_IRQ_EXIT_ON_IRQ_STACK
+    - drm/bridge: analogix_dp: Support PSR-exit to disable transition
+    - drm/atomic: Force bridge self-refresh-exit on CRTC switch
+    - drm/amdgpu: update VCN codec support for Yellow Carp
+    - powerpc/32: Fix overread/overwrite of thread_struct via ptrace
+    - powerpc/mm: Switch obsolete dssall to .long
+    - drm/ast: Create threshold values for AST2600
+    - random: avoid checking crng_ready() twice in random_init()
+    - random: mark bootloader randomness code as __init
+    - random: account for arch randomness in bits
+    - md/raid0: Ignore RAID0 layout if the second zone has only one device
+    - net/sched: act_police: more accurate MTU policing
+    - PCI: qcom: Fix pipe clock imbalance
+    - zonefs: fix handling of explicit_open option on mount
+    - iov_iter: fix build issue due to possible type mis-match
+    - dmaengine: idxd: add missing callback function to support DMA_INTERRUPT
+    - tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd
+    - xsk: Fix possible crash when multiple sockets are created
+    - Linux 5.15.47
+  * CVE-2022-36946
+    - netfilter: nf_queue: do not allow packet truncation below transport header
+      offset
+  * CVE-2021-33655
+    - fbcon: Disallow setting font bigger than screen size
+    - fbcon: Prevent that screen size is smaller than font size
+    - fbmem: Check virtual screen sizes in fb_set_var()
+
+  [ Ubuntu: 5.15.0-47.51 ]
+
+  * jammy/linux: 5.15.0-47.51 -proposed tracker (LP: #1983903)
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - UBUNTU: [Packaging] Move python3-dev to build-depends
+  * touchpad and touchscreen doesn't work at all on ACER Spin 5 (SP513-54N)
+    (LP: #1884232)
+    - x86/PCI: Eliminate remove_e820_regions() common subexpressions
+    - x86: Log resource clipping for E820 regions
+    - x86/PCI: Clip only host bridge windows for E820 regions
+    - x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
+    - x86/PCI: Disable E820 reserved region clipping via quirks
+    - x86/PCI: Revert "x86/PCI: Clip only host bridge windows for E820 regions"
+  * [SRU][H/OEM-5.13/OEM-5.14/U][J/OEM-5.17/U] Fix invalid MAC address after
+    hotplug tbt dock (LP: #1942999)
+    - SAUCE: igc: wait for the MAC copy when enabled MAC passthrough
+  * Mass Storage Gadget driver truncates device >2TB (LP: #1981390)
+    - usb: gadget: storage: add support for media larger than 2T
+  * AMD Rembrandt: DP tunneling fails with Thunderbolt monitors (LP: #1983143)
+    - SAUCE: drm/amd: Fix DP Tunneling with Thunderbolt monitors
+    - drm/amd/display: Fix for dmub outbox notification enable
+    - Revert "drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset"
+    - drm/amd/display: Reset link encoder assignments for GPU reset
+    - drm/amd/display: Fix DPIA outbox timeout after S3/S4/reset
+    - drm/amd/display: Fix new dmub notification enabling in DM
+    - SAUCE: thunderbolt: Add DP out resource when DP tunnel is discovered.
+  * Fix sub-optimal I210 network speed (LP: #1976438)
+    - igb: Make DMA faster when CPU is active on the PCIe link
+  * e1000e report hardware hang (LP: #1973104)
+    - e1000e: Enable GPT clock before sending message to CSME
+    - Revert "e1000e: Fix possible HW unit hang after an s0ix exit"
+  * ioam6.sh in net from ubuntu_kernel_selftests fails with 5.15 kernels in
+    Focal (LP: #1982930)
+    - selftests: net: fix IOAM test skip return code
+  * Additional fix for TGL + AUO panel flickering (LP: #1983297)
+    - Revert "UBUNTU: SAUCE: drm/i915/display/psr: Fix flicker on TGL + AUO panel"
+    - drm/i915/display: Fix sel fetch plane offset calculation
+    - drm/i915: Nuke ORIGIN_GTT
+    - drm/i915/display: Drop PSR support from HSW and BDW
+    - drm/i915/display/psr: Handle plane and pipe restrictions at every page flip
+    - drm/i915/display/psr: Do full fetch when handling multi-planar formats
+    - drm/i915/display: Drop unnecessary frontbuffer flushes
+    - drm/i915/display: Handle frontbuffer rendering when PSR2 selective fetch is
+      enabled
+    - drm/i915/display: Fix glitches when moving cursor with PSR2 selective fetch
+      enabled
+    - SAUCE: drm/i915/display/psr: Reinstate fix for TGL + AUO panel flicker
+  * AMD Yellow Carp DMCUB fw update for s0i3 B0 fixes (LP: #1957026)
+    - drm/amd/display: Optimize bandwidth on following fast update
+    - drm/amd/display: Fix surface optimization regression on Carrizo
+    - drm/amd/display: Reset DMCUB before HW init
+  * GPIO character device v1 API not enabled in kernel (LP: #1953613)
+    - [Config] Enable CONFIG_GPIO_CDEV_V1
+  * intel_iommu: Fix  enable intel_iommu, Ubuntu 22.04 installation crashes
+    (LP: #1982104)
+    - iommu/vt-d: Fix RID2PASID setup/teardown failure
+  * Headset mic with Cirrus logic codec doesn't work (LP: #1972815)
+    - ASoC: cs42l42: Move CS42L42 register descriptions to general include
+    - ALSA: hda/cs8409: Use general cs42l42 include in cs8409 hda driver
+    - ALSA: hda/cs8409: Support manual mode detection for CS42L42
+  * Failed to resume from S3 blocked by atlantic driver[1d6a:94c0]
+    (LP: #1981950)
+    - net: atlantic: remove deep parameter on suspend/resume functions
+    - net: atlantic: remove aq_nic_deinit() when resume
+  * Make cm32181 sensor work after system suspend (LP: #1981773)
+    - iio: light: cm32181: Add PM support
+  * Clear PCI errors left from BIOS (LP: #1981173)
+    - PCI: Clear PCI_STATUS when setting up device
+  * Fix AMDGPU blank screen when Type-C DP alt is in use (LP: #1980060)
+    - drm/amd/display: Query DMCUB for dp alt status
+    - drm/amd/display: Add version check before using DP alt query interface
+  * Fix WD22TB4 suspend and resume, two external monitor can not output
+    (LP: #1979267)
+    - drm/dp/mst: Read the extended DPCD capabilities during system resume
+  * [SRU] bcache deadlock during read IO in writeback mode (LP: #1980925)
+    - bcache: memset on stack variables in bch_btree_check() and
+      bch_sectors_dirty_init()
+  * Audio mute key (f5) LED and Mic mute key (f8) LED are no function on HP
+    440/450/640/650 G9 (LP: #1982716)
+    - ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
+  * Enable WiFi hotspot feature for MediaTek MT7921 (LP: #1979173)
+    - mt76: mt7921: Add AP mode support
+    - mt76: mt7921: not support beacon offload disable command
+    - mt76: mt7921: fix command timeout in AP stop period
+  * Fix drm/amd/pm: enable ASPM by default (LP: #1966680)
+    - drm/amd: Refactor `amdgpu_aspm` to be evaluated per device
+    - drm/amd: Use amdgpu_device_should_use_aspm on navi umd pstate switching
+    - drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems
+  * Power cycle USB ports on shutdown/reboot (LP: #1976503)
+    - xhci: turn off port power in shutdown
+  * Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - binfmt_flat: do not stop relocating GOT entries prematurely on riscv
+    - parisc/stifb: Implement fb_is_primary_device()
+    - parisc/stifb: Keep track of hardware path of graphics card
+    - RISC-V: Mark IORESOURCE_EXCLUSIVE for reserved mem instead of
+      IORESOURCE_BUSY
+    - riscv: Initialize thread pointer before calling C functions
+    - riscv: Fix irq_work when SMP is disabled
+    - riscv: Wire up memfd_secret in UAPI header
+    - riscv: Move alternative length validation into subsection
+    - ALSA: hda/realtek - Add new type for ALC245
+    - ALSA: hda/realtek: Enable 4-speaker output for Dell XPS 15 9520 laptop
+    - ALSA: hda/realtek - Fix microphone noise on ASUS TUF B550M-PLUS
+    - ALSA: usb-audio: Cancel pending work at closing a MIDI substream
+    - USB: serial: option: add Quectel BG95 modem
+    - USB: new quirk for Dell Gen 2 devices
+    - usb: isp1760: Fix out-of-bounds array access
+    - usb: dwc3: gadget: Move null pinter check to proper place
+    - usb: core: hcd: Add support for deferring roothub registration
+    - fs/ntfs3: Update valid size if -EIOCBQUEUED
+    - fs/ntfs3: Fix fiemap + fix shrink file size (to remove preallocated space)
+    - fs/ntfs3: Keep preallocated only if option prealloc enabled
+    - fs/ntfs3: Check new size for limits
+    - fs/ntfs3: In function ntfs_set_acl_ex do not change inode->i_mode if called
+      from function ntfs_init_acl
+    - fs/ntfs3: Fix some memory leaks in an error handling path of 'log_replay()'
+    - fs/ntfs3: Update i_ctime when xattr is added
+    - fs/ntfs3: Restore ntfs_xattr_get_acl and ntfs_xattr_set_acl functions
+    - cifs: fix potential double free during failed mount
+    - cifs: when extending a file with falloc we should make files not-sparse
+    - xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
+    - platform/x86: intel-hid: fix _DSM function index handling
+    - x86/MCE/AMD: Fix memory leak when threshold_create_bank() fails
+    - perf/x86/intel: Fix event constraints for ICL
+    - x86/kexec: fix memory leak of elf header buffer
+    - x86/sgx: Set active memcg prior to shmem allocation
+    - ptrace/um: Replace PT_DTRACE with TIF_SINGLESTEP
+    - ptrace/xtensa: Replace PT_SINGLESTEP with TIF_SINGLESTEP
+    - ptrace: Reimplement PTRACE_KILL by always sending SIGKILL
+    - btrfs: add "0x" prefix for unsupported optional features
+    - btrfs: return correct error number for __extent_writepage_io()
+    - btrfs: repair super block num_devices automatically
+    - btrfs: fix the error handling for submit_extent_page() for
+      btrfs_do_readpage()
+    - iommu/vt-d: Add RPLS to quirk list to skip TE disabling
+    - drm/vmwgfx: validate the screen formats
+    - drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes
+    - selftests/bpf: Fix vfs_link kprobe definition
+    - selftests/bpf: Fix parsing of prog types in UAPI hdr for bpftool sync
+    - mwifiex: add mutex lock for call in mwifiex_dfs_chan_sw_work_queue
+    - b43legacy: Fix assigning negative value to unsigned variable
+    - b43: Fix assigning negative value to unsigned variable
+    - ipw2x00: Fix potential NULL dereference in libipw_xmit()
+    - ipv6: fix locking issues with loops over idev->addr_list
+    - fbcon: Consistently protect deferred_takeover with console_lock()
+    - x86/platform/uv: Update TSC sync state for UV5
+    - ACPICA: Avoid cache flush inside virtual machines
+    - mac80211: minstrel_ht: fix where rate stats are stored (fixes debugfs
+      output)
+    - drm/komeda: return early if drm_universal_plane_init() fails.
+    - drm/amd/display: Disabling Z10 on DCN31
+    - rcu-tasks: Fix race in schedule and flush work
+    - rcu: Make TASKS_RUDE_RCU select IRQ_WORK
+    - sfc: ef10: Fix assigning negative value to unsigned variable
+    - ALSA: jack: Access input_dev under mutex
+    - spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA
+      direction
+    - tools/power turbostat: fix ICX DRAM power numbers
+    - scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg()
+    - scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock
+    - scsi: lpfc: Fix call trace observed during I/O with CMF enabled
+    - cpuidle: PSCI: Improve support for suspend-to-RAM for PSCI OSI mode
+    - drm/amd/pm: fix double free in si_parse_power_table()
+    - ASoC: rsnd: care default case on rsnd_ssiu_busif_err_status_clear()
+    - ASoC: rsnd: care return value from rsnd_node_fixed_index()
+    - ath9k: fix QCA9561 PA bias level
+    - media: venus: hfi: avoid null dereference in deinit
+    - media: pci: cx23885: Fix the error handling in cx23885_initdev()
+    - media: cx25821: Fix the warning when removing the module
+    - md/bitmap: don't set sb values if can't pass sanity check
+    - mmc: jz4740: Apply DMA engine limits to maximum segment size
+    - drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit
+    - scsi: megaraid: Fix error check return value of register_chrdev()
+    - drm/amdgpu/sdma: Fix incorrect calculations of the wptr of the doorbells
+    - scsi: ufs: Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync()
+    - scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp()
+    - ath11k: disable spectral scan during spectral deinit
+    - ASoC: Intel: bytcr_rt5640: Add quirk for the HP Pro Tablet 408
+    - drm/plane: Move range check for format_count earlier
+    - drm/amd/pm: fix the compile warning
+    - ath10k: skip ath10k_halt during suspend for driver state RESTARTING
+    - arm64: compat: Do not treat syscall number as ESR_ELx for a bad syscall
+    - drm: msm: fix error check return value of irq_of_parse_and_map()
+    - scsi: target: tcmu: Fix possible data corruption
+    - ipv6: Don't send rs packets to the interface of ARPHRD_TUNNEL
+    - net/mlx5: fs, delete the FTE when there are no rules attached to it
+    - ASoC: dapm: Don't fold register value changes into notifications
+    - mlxsw: spectrum_dcb: Do not warn about priority changes
+    - mlxsw: Treat LLDP packets as control
+    - drm/amdgpu/psp: move PSP memory alloc from hw_init to sw_init
+    - drm/amdgpu/ucode: Remove firmware load type check in amdgpu_ucode_free_bo
+    - regulator: mt6315: Enforce regulator-compatible, not name
+    - HID: bigben: fix slab-out-of-bounds Write in bigben_probe
+    - of: Support more than one crash kernel regions for kexec -s
+    - ASoC: tscs454: Add endianness flag in snd_soc_component_driver
+    - scsi: lpfc: Alter FPIN stat accounting logic
+    - net: remove two BUG() from skb_checksum_help()
+    - s390/preempt: disable __preempt_count_add() optimization for
+      PROFILE_ALL_BRANCHES
+    - perf/amd/ibs: Cascade pmu init functions' return value
+    - sched/core: Avoid obvious double update_rq_clock warning
+    - spi: stm32-qspi: Fix wait_cmd timeout in APM mode
+    - dma-debug: change allocation mode from GFP_NOWAIT to GFP_ATIOMIC
+    - ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default
+    - ipmi:ssif: Check for NULL msg when handling events and messages
+    - ipmi: Fix pr_fmt to avoid compilation issues
+    - rtlwifi: Use pr_warn instead of WARN_ONCE
+    - mt76: mt7921: accept rx frames with non-standard VHT MCS10-11
+    - mt76: fix encap offload ethernet type check
+    - media: rga: fix possible memory leak in rga_probe
+    - media: coda: limit frame interval enumeration to supported encoder frame
+      sizes
+    - media: hantro: HEVC: unconditionnaly set pps_{cb/cr}_qp_offset values
+    - media: ccs-core.c: fix failure to call clk_disable_unprepare
+    - media: imon: reorganize serialization
+    - media: cec-adap.c: fix is_configuring state
+    - usbnet: Run unregister_netdev() before unbind() again
+    - openrisc: start CPU timer early in boot
+    - nvme-pci: fix a NULL pointer dereference in nvme_alloc_admin_tags
+    - ASoC: rt5645: Fix errorenous cleanup order
+    - nbd: Fix hung on disconnect request if socket is closed before
+    - drm/amd/pm: update smartshift powerboost calc for smu12
+    - drm/amd/pm: update smartshift powerboost calc for smu13
+    - net: phy: micrel: Allow probing without .driver_data
+    - media: exynos4-is: Fix compile warning
+    - media: hantro: Stop using H.264 parameter pic_num
+    - ASoC: max98357a: remove dependency on GPIOLIB
+    - ASoC: rt1015p: remove dependency on GPIOLIB
+    - ACPI: CPPC: Assume no transition latency if no PCCT
+    - nvme: set non-mdts limits in nvme_scan_work
+    - can: mcp251xfd: silence clang's -Wunaligned-access warning
+    - x86/microcode: Add explicit CPU vendor dependency
+    - net: ipa: ignore endianness if there is no header
+    - m68k: atari: Make Atari ROM port I/O write macros return void
+    - rxrpc: Return an error to sendmsg if call failed
+    - rxrpc, afs: Fix selection of abort codes
+    - afs: Adjust ACK interpretation to try and cope with NAT
+    - eth: tg3: silence the GCC 12 array-bounds warning
+    - char: tpm: cr50_i2c: Suppress duplicated error message in .remove()
+    - selftests/bpf: fix btf_dump/btf_dump due to recent clang change
+    - gfs2: use i_lock spin_lock for inode qadata
+    - scsi: target: tcmu: Avoid holding XArray lock when calling lock_page
+    - IB/rdmavt: add missing locks in rvt_ruc_loopback
+    - ARM: dts: ox820: align interrupt controller node name with dtschema
+    - ARM: dts: socfpga: align interrupt controller node name with dtschema
+    - ARM: dts: s5pv210: align DMA channels with dtschema
+    - arm64: dts: qcom: msm8994: Fix the cont_splash_mem address
+    - arm64: dts: qcom: msm8994: Fix BLSP[12]_DMA channels count
+    - PM / devfreq: rk3399_dmc: Disable edev on remove()
+    - crypto: ccree - use fine grained DMA mapping dir
+    - soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc
+    - fs: jfs: fix possible NULL pointer dereference in dbFree()
+    - arm64: dts: qcom: sdm845-xiaomi-beryllium: fix typo in panel's vddio-supply
+      property
+    - ALSA: usb-audio: Add quirk bits for enabling/disabling generic implicit fb
+    - ALSA: usb-audio: Move generic implicit fb quirk entries into quirks.c
+    - ARM: OMAP1: clock: Fix UART rate reporting algorithm
+    - powerpc/fadump: Fix fadump to work with a different endian capture kernel
+    - fat: add ratelimit to fat*_ent_bread()
+    - pinctrl: renesas: rzn1: Fix possible null-ptr-deref in
+      sh_pfc_map_resources()
+    - ARM: versatile: Add missing of_node_put in dcscb_init
+    - ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROM
+    - ARM: hisi: Add missing of_node_put after of_find_compatible_node
+    - cpufreq: Avoid unnecessary frequency updates due to mismatch
+    - powerpc/rtas: Keep MSR[RI] set when calling RTAS
+    - PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
+    - KVM: PPC: Book3S HV Nested: L2 LPCR should inherit L1 LPES setting
+    - alpha: fix alloc_zeroed_user_highpage_movable()
+    - tracing: incorrect isolate_mote_t cast in mm_vmscan_lru_isolate
+    - powerpc/powernv/vas: Assign real address to rx_fifo in vas_rx_win_attr
+    - powerpc/xics: fix refcount leak in icp_opal_init()
+    - powerpc/powernv: fix missing of_node_put in uv_init()
+    - macintosh/via-pmu: Fix build failure when CONFIG_INPUT is disabled
+    - powerpc/iommu: Add missing of_node_put in iommu_init_early_dart
+    - smb3: check for null tcon
+    - RDMA/hfi1: Prevent panic when SDMA is disabled
+    - Input: gpio-keys - cancel delayed work only in case of GPIO
+    - drm: fix EDID struct for old ARM OABI format
+    - drm/bridge_connector: enable HPD by default if supported
+    - dt-bindings: display: sitronix, st7735r: Fix backlight in example
+    - drm/vmwgfx: Fix an invalid read
+    - ath11k: acquire ab->base_lock in unassign when finding the peer by addr
+    - drm: bridge: it66121: Fix the register page length
+    - ath9k: fix ar9003_get_eepmisc
+    - drm/edid: fix invalid EDID extension block filtering
+    - drm/bridge: adv7511: clean up CEC adapter when probe fails
+    - drm: bridge: icn6211: Fix register layout
+    - drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling
+    - mtd: spinand: gigadevice: fix Quad IO for GD5F1GQ5UExxG
+    - spi: qcom-qspi: Add minItems to interconnect-names
+    - ASoC: mediatek: Fix error handling in mt8173_max98090_dev_probe
+    - ASoC: mediatek: Fix missing of_node_put in mt2701_wm8960_machine_probe
+    - x86/delay: Fix the wrong asm constraint in delay_loop()
+    - drm/vc4: hvs: Fix frame count register readout
+    - drm/mediatek: Fix mtk_cec_mask()
+    - drm/vc4: hvs: Reset muxes at probe time
+    - drm/vc4: txp: Don't set TXP_VSTART_AT_EOF
+    - drm/vc4: txp: Force alpha to be 0xff if it's disabled
+    - libbpf: Don't error out on CO-RE relos for overriden weak subprogs
+    - x86/PCI: Fix ALi M1487 (IBC) PIRQ router link value interpretation
+    - mptcp: reset the packet scheduler on PRIO change
+    - nl80211: show SSID for P2P_GO interfaces
+    - drm/komeda: Fix an undefined behavior bug in komeda_plane_add()
+    - drm: mali-dp: potential dereference of null pointer
+    - spi: spi-ti-qspi: Fix return value handling of wait_for_completion_timeout
+    - scftorture: Fix distribution of short handler delays
+    - net: dsa: mt7530: 1G can also support 1000BASE-X link mode
+    - ixp4xx_eth: fix error check return value of platform_get_irq()
+    - NFC: NULL out the dev->rfkill to prevent UAF
+    - efi: Add missing prototype for efi_capsule_setup_info
+    - device property: Check fwnode->secondary when finding properties
+    - device property: Allow error pointer to be passed to fwnode APIs
+    - target: remove an incorrect unmap zeroes data deduction
+    - drbd: fix duplicate array initializer
+    - EDAC/dmc520: Don't print an error for each unconfigured interrupt line
+    - mtd: rawnand: denali: Use managed device resources
+    - HID: hid-led: fix maximum brightness for Dream Cheeky
+    - HID: elan: Fix potential double free in elan_input_configured
+    - drm/bridge: Fix error handling in analogix_dp_probe
+    - regulator: da9121: Fix uninit-value in da9121_assign_chip_model()
+    - drm/mediatek: dpi: Use mt8183 output formats for mt8192
+    - signal: Deliver SIGTRAP on perf event asynchronously if blocked
+    - sched/fair: Fix cfs_rq_clock_pelt() for throttled cfs_rq
+    - sched/psi: report zeroes for CPU full at the system level
+    - spi: img-spfi: Fix pm_runtime_get_sync() error checking
+    - cpufreq: Fix possible race in cpufreq online error path
+    - printk: use atomic updates for klogd work
+    - printk: add missing memory barrier to wake_up_klogd()
+    - printk: wake waiters for safe and NMI contexts
+    - ath9k_htc: fix potential out of bounds access with invalid
+      rxstatus->rs_keyix
+    - media: i2c: max9286: Use dev_err_probe() helper
+    - media: i2c: max9286: Use "maxim,gpio-poc" property
+    - media: i2c: max9286: fix kernel oops when removing module
+    - media: hantro: Empty encoder capture buffers by default
+    - drm/panel: simple: Add missing bus flags for Innolux G070Y2-L01
+    - ALSA: pcm: Check for null pointer of pointer substream before dereferencing
+      it
+    - mtdblock: warn if opened on NAND
+    - inotify: show inotify mask flags in proc fdinfo
+    - fsnotify: fix wrong lockdep annotations
+    - spi: rockchip: Stop spi slave dma receiver when cs inactive
+    - spi: rockchip: Preset cs-high and clk polarity in setup progress
+    - spi: rockchip: fix missing error on unsupported SPI_CS_HIGH
+    - of: overlay: do not break notify on NOTIFY_{OK|STOP}
+    - selftests/damon: add damon to selftests root Makefile
+    - drm/msm/dp: Modify prototype of encoder based API
+    - drm/msm/hdmi: switch to drm_bridge_connector
+    - drm/msm/dpu: adjust display_v_end for eDP and DP
+    - scsi: iscsi: Fix harmless double shift bug
+    - scsi: ufs: qcom: Fix ufs_qcom_resume()
+    - scsi: ufs: core: Exclude UECxx from SFR dump list
+    - drm/v3d: Fix null pointer dereference of pointer perfmon
+    - selftests/resctrl: Fix null pointer dereference on open failed
+    - libbpf: Fix logic for finding matching program for CO-RE relocation
+    - mtd: spi-nor: core: Check written SR value in
+      spi_nor_write_16bit_sr_and_check()
+    - x86/pm: Fix false positive kmemleak report in msr_build_context()
+    - mtd: rawnand: cadence: fix possible null-ptr-deref in
+      cadence_nand_dt_probe()
+    - mtd: rawnand: intel: fix possible null-ptr-deref in ebu_nand_probe()
+    - x86/speculation: Add missing prototype for unpriv_ebpf_notify()
+    - ASoC: rk3328: fix disabling mclk on pclk probe failure
+    - perf tools: Add missing headers needed by util/data.h
+    - drm/msm/disp/dpu1: set vbif hw config to NULL to avoid use after memory free
+      during pm runtime resume
+    - drm/msm/dp: stop event kernel thread when DP unbind
+    - drm/msm/dp: fix error check return value of irq_of_parse_and_map()
+    - drm/msm/dp: reset DP controller before transmit phy test pattern
+    - drm/msm/dp: do not stop transmitting phy test pattern during DP phy
+      compliance test
+    - drm/msm/dsi: fix error checks and return values for DSI xmit functions
+    - drm/msm/hdmi: check return value after calling
+      platform_get_resource_byname()
+    - drm/msm/hdmi: fix error check return value of irq_of_parse_and_map()
+    - drm/msm: add missing include to msm_drv.c
+    - drm/panel: panel-simple: Fix proper bpc for AM-1280800N3TZQW-T00H
+    - kunit: fix debugfs code to use enum kunit_status, not bool
+    - drm/rockchip: vop: fix possible null-ptr-deref in vop_bind()
+    - spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA
+    - [Packaging] add python3-dev as build dependency
+    - perf tools: Use Python devtools for version autodetection rather than
+      runtime
+    - virtio_blk: fix the discard_granularity and discard_alignment queue limits
+    - nl80211: don't hold RTNL in color change request
+    - x86: Fix return value of __setup handlers
+    - irqchip/exiu: Fix acknowledgment of edge triggered interrupts
+    - irqchip/aspeed-i2c-ic: Fix irq_of_parse_and_map() return value
+    - irqchip/aspeed-scu-ic: Fix irq_of_parse_and_map() return value
+    - x86/mm: Cleanup the control_va_addr_alignment() __setup handler
+    - arm64: fix types in copy_highpage()
+    - regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
+    - drm/msm/dsi: fix address for second DSI PHY on SDM660
+    - drm/msm/dp: fix event thread stuck in wait_event after kthread_stop()
+    - drm/msm/mdp5: Return error code in mdp5_pipe_release when deadlock is
+      detected
+    - drm/msm/mdp5: Return error code in mdp5_mixer_release when deadlock is
+      detected
+    - drm/msm: return an error pointer in msm_gem_prime_get_sg_table()
+    - media: uvcvideo: Fix missing check to determine if element is found in list
+    - arm64: stackleak: fix current_top_of_stack()
+    - iomap: iomap_write_failed fix
+    - spi: spi-fsl-qspi: check return value after calling
+      platform_get_resource_byname()
+    - Revert "cpufreq: Fix possible race in cpufreq online error path"
+    - regulator: qcom_smd: Fix up PM8950 regulator configuration
+    - samples: bpf: Don't fail for a missing VMLINUX_BTF when VMLINUX_H is
+      provided
+    - perf/amd/ibs: Use interrupt regs ip for stack unwinding
+    - ath11k: Don't check arvif->is_started before sending management frames
+    - wilc1000: fix crash observed in AP mode with cfg80211_register_netdevice()
+    - HID: amd_sfh: Modify the bus name
+    - HID: amd_sfh: Modify the hid name
+    - ASoC: fsl: Use dev_err_probe() helper
+    - ASoC: fsl: Fix refcount leak in imx_sgtl5000_probe
+    - ASoC: imx-hdmi: Fix refcount leak in imx_hdmi_probe
+    - ASoC: mxs-saif: Fix refcount leak in mxs_saif_probe
+    - regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
+    - dma-direct: factor out a helper for DMA_ATTR_NO_KERNEL_MAPPING allocations
+    - dma-direct: don't fail on highmem CMA pages in dma_direct_alloc_pages
+    - ASoC: samsung: Use dev_err_probe() helper
+    - ASoC: samsung: Fix refcount leak in aries_audio_probe
+    - block: Fix the bio.bi_opf comment
+    - kselftest/cgroup: fix test_stress.sh to use OUTPUT dir
+    - scripts/faddr2line: Fix overlapping text section failures
+    - media: aspeed: Fix an error handling path in aspeed_video_probe()
+    - media: exynos4-is: Fix PM disable depth imbalance in fimc_is_probe
+    - mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
+    - mt76: do not attempt to reorder received 802.3 packets without agg session
+    - media: st-delta: Fix PM disable depth imbalance in delta_probe
+    - media: atmel: atmel-isc: Fix PM disable depth imbalance in atmel_isc_probe
+    - media: i2c: rdacm2x: properly set subdev entity function
+    - media: exynos4-is: Change clk_disable to clk_disable_unprepare
+    - media: pvrusb2: fix array-index-out-of-bounds in pvr2_i2c_core_init
+    - media: vsp1: Fix offset calculation for plane cropping
+    - media: atmel: atmel-sama5d2-isc: fix wrong mask in YUYV format check
+    - media: hantro: HEVC: Fix tile info buffer value computation
+    - Bluetooth: fix dangling sco_conn and use-after-free in sco_sock_timeout
+    - Bluetooth: use hdev lock in activate_scan for hci_is_adv_monitoring
+    - Bluetooth: use hdev lock for accept_list and reject_list in conn req
+    - nvme: set dma alignment to dword
+    - m68k: math-emu: Fix dependencies of math emulation support
+    - sctp: read sk->sk_bound_dev_if once in sctp_rcv()
+    - net: hinic: add missing destroy_workqueue in hinic_pf_to_mgmt_init
+    - ASoC: ti: j721e-evm: Fix refcount leak in j721e_soc_probe_*
+    - kselftest/arm64: bti: force static linking
+    - media: ov7670: remove ov7670_power_off from ov7670_remove
+    - media: i2c: ov5648: fix wrong pointer passed to IS_ERR() and PTR_ERR()
+    - media: staging: media: rkvdec: Make use of the helper function
+      devm_platform_ioremap_resource()
+    - media: rkvdec: h264: Fix dpb_valid implementation
+    - media: rkvdec: h264: Fix bit depth wrap in pps packet
+    - regulator: scmi: Fix refcount leak in scmi_regulator_probe
+    - ext4: reject the 'commit' option on ext2 filesystems
+    - drm/msm/a6xx: Fix refcount leak in a6xx_gpu_init
+    - drm: msm: fix possible memory leak in mdp5_crtc_cursor_set()
+    - x86/sev: Annotate stack change in the #VC handler
+    - drm/msm: don't free the IRQ if it was not requested
+    - selftests/bpf: Add missed ima_setup.sh in Makefile
+    - drm/msm/dpu: handle pm_runtime_get_sync() errors in bind path
+    - drm/i915: Fix CFI violation with show_dynamic_id()
+    - thermal/drivers/bcm2711: Don't clamp temperature at zero
+    - thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe
+    - thermal/core: Fix memory leak in __thermal_cooling_device_register()
+    - thermal/drivers/imx_sc_thermal: Fix refcount leak in imx_sc_thermal_probe
+    - bfq: Relax waker detection for shared queues
+    - bfq: Allow current waker to defend against a tentative one
+    - ASoC: wm2000: fix missing clk_disable_unprepare() on error in
+      wm2000_anc_transition()
+    - PM: domains: Fix initialization of genpd's next_wakeup
+    - net: macb: Fix PTP one step sync support
+    - NFC: hci: fix sleep in atomic context bugs in nfc_hci_hcp_message_tx
+    - ASoC: max98090: Move check for invalid values before casting in
+      max98090_put_enab_tlv()
+    - net: stmmac: selftests: Use kcalloc() instead of kzalloc()
+    - net: stmmac: fix out-of-bounds access in a selftest
+    - hv_netvsc: Fix potential dereference of NULL pointer
+    - hwmon: (pmbus) Check PEC support before reading other registers
+    - rxrpc: Fix listen() setting the bar too high for the prealloc rings
+    - rxrpc: Don't try to resend the request if we're receiving the reply
+    - rxrpc: Fix overlapping ACK accounting
+    - rxrpc: Don't let ack.previousPacket regress
+    - rxrpc: Fix decision on when to generate an IDLE ACK
+    - net: huawei: hinic: Use devm_kcalloc() instead of devm_kzalloc()
+    - hinic: Avoid some over memory allocation
+    - net: dsa: restrict SMSC_LAN9303_I2C kconfig
+    - net/smc: postpone sk_refcnt increment in connect()
+    - dma-direct: factor out dma_set_{de,en}crypted helpers
+    - dma-direct: don't call dma_set_decrypted for remapped allocations
+    - dma-direct: always leak memory that can't be re-encrypted
+    - dma-direct: don't over-decrypt memory
+    - arm64: dts: rockchip: Move drive-impedance-ohm to emmc phy on rk3399
+    - arm64: dts: mt8192: Fix nor_flash status disable typo
+    - memory: samsung: exynos5422-dmc: Avoid some over memory allocation
+    - ARM: dts: BCM5301X: update CRU block description
+    - ARM: dts: BCM5301X: Update pin controller node name
+    - ARM: dts: suniv: F1C100: fix watchdog compatible
+    - soc: qcom: smp2p: Fix missing of_node_put() in smp2p_parse_ipc
+    - soc: qcom: smsm: Fix missing of_node_put() in smsm_parse_ipc
+    - PCI: cadence: Fix find_first_zero_bit() limit
+    - PCI: rockchip: Fix find_first_zero_bit() limit
+    - PCI: mediatek: Fix refcount leak in mtk_pcie_subsys_powerup()
+    - PCI: dwc: Fix setting error return on MSI DMA mapping failure
+    - ARM: dts: ci4x10: Adapt to changes in imx6qdl.dtsi regarding fec clocks
+    - soc: qcom: llcc: Add MODULE_DEVICE_TABLE()
+    - KVM: nVMX: Leave most VM-Exit info fields unmodified on failed VM-Entry
+    - KVM: nVMX: Clear IDT vectoring on nested VM-Exit for double/triple fault
+    - crypto: qat - set CIPHER capability for QAT GEN2
+    - crypto: qat - set COMPRESSION capability for QAT GEN2
+    - crypto: qat - set CIPHER capability for DH895XCC
+    - crypto: qat - set COMPRESSION capability for DH895XCC
+    - platform/chrome: cros_ec: fix error handling in cros_ec_register()
+    - ARM: dts: imx6dl-colibri: Fix I2C pinmuxing
+    - platform/chrome: Re-introduce cros_ec_cmd_xfer and use it for ioctls
+    - can: xilinx_can: mark bit timing constants as const
+    - ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
+    - ARM: dts: bcm2835-rpi-zero-w: Fix GPIO line name for Wifi/BT
+    - ARM: dts: bcm2837-rpi-cm3-io3: Fix GPIO line names for SMPS I2C
+    - ARM: dts: bcm2837-rpi-3-b-plus: Fix GPIO line name of power LED
+    - ARM: dts: bcm2835-rpi-b: Fix GPIO line names
+    - misc: ocxl: fix possible double free in ocxl_file_register_afu
+    - crypto: marvell/cesa - ECB does not IV
+    - gpiolib: of: Introduce hook for missing gpio-ranges
+    - pinctrl: bcm2835: implement hook for missing gpio-ranges
+    - arm: mediatek: select arch timer for mt7629
+    - pinctrl/rockchip: support deferring other gpio params
+    - pinctrl: mediatek: mt8195: enable driver on mtk platforms
+    - arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
+    - Drivers: hv: vmbus: Fix handling of messages with transaction ID of zero
+    - powerpc/fadump: fix PT_LOAD segment for boot memory area
+    - mfd: ipaq-micro: Fix error check return value of platform_get_irq()
+    - scsi: fcoe: Fix Wstringop-overflow warnings in fcoe_wwn_from_mac()
+    - soc: bcm: Check for NULL return of devm_kzalloc()
+    - arm64: dts: ti: k3-am64-mcu: remove incorrect UART base clock rates
+    - ASoC: sh: rz-ssi: Check return value of pm_runtime_resume_and_get()
+    - ASoC: sh: rz-ssi: Propagate error codes returned from
+      platform_get_irq_byname()
+    - ASoC: sh: rz-ssi: Release the DMA channels in rz_ssi_probe() error path
+    - firmware: arm_scmi: Fix list protocols enumeration in the base protocol
+    - nvdimm: Fix firmware activation deadlock scenarios
+    - nvdimm: Allow overwrite in the presence of disabled dimms
+    - pinctrl: mvebu: Fix irq_of_parse_and_map() return value
+    - drivers/base/node.c: fix compaction sysfs file leak
+    - dax: fix cache flush on PMD-mapped pages
+    - drivers/base/memory: fix an unlikely reference counting issue in
+      __add_memory_block()
+    - firmware: arm_ffa: Fix uuid parameter to ffa_partition_probe
+    - firmware: arm_ffa: Remove incorrect assignment of driver_data
+    - list: introduce list_is_head() helper and re-use it in list.h
+    - list: fix a data-race around ep->rdllist
+    - drm/msm/dpu: fix error check return value of irq_of_parse_and_map()
+    - powerpc/8xx: export 'cpm_setbrg' for modules
+    - pinctrl: renesas: r8a779a0: Fix GPIO function on I2C-capable pins
+    - pinctrl: renesas: core: Fix possible null-ptr-deref in
+      sh_pfc_map_resources()
+    - powerpc/idle: Fix return value of __setup() handler
+    - powerpc/4xx/cpm: Fix return value of __setup() handler
+    - RDMA/hns: Add the detection for CMDQ status in the device initialization
+      process
+    - arm64: dts: marvell: espressobin-ultra: fix SPI-NOR config
+    - arm64: dts: marvell: espressobin-ultra: enable front USB3 port
+    - ASoC: atmel-pdmic: Remove endianness flag on pdmic component
+    - ASoC: atmel-classd: Remove endianness flag on class d component
+    - proc: fix dentry/inode overinstantiating under /proc/${pid}/net
+    - ipc/mqueue: use get_tree_nodev() in mqueue_get_tree()
+    - PCI: imx6: Fix PERST# start-up sequence
+    - tty: fix deadlock caused by calling printk() under tty_port->lock
+    - crypto: sun8i-ss - rework handling of IV
+    - crypto: sun8i-ss - handle zero sized sg
+    - crypto: cryptd - Protect per-CPU resource by disabling BH.
+    - ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
+    - hugetlbfs: fix hugetlbfs_statfs() locking
+    - Input: sparcspkr - fix refcount leak in bbc_beep_probe
+    - PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
+    - PCI: microchip: Fix potential race in interrupt handling
+    - hwrng: omap3-rom - fix using wrong clk_disable() in
+      omap_rom_rng_runtime_resume()
+    - powerpc/64: Only WARN if __pa()/__va() called with bad addresses
+    - powerpc/perf: Fix the threshold compare group constraint for power10
+    - powerpc/perf: Fix the threshold compare group constraint for power9
+    - macintosh: via-pmu and via-cuda need RTC_LIB
+    - powerpc/xive: Add some error handling code to 'xive_spapr_init()'
+    - powerpc/xive: Fix refcount leak in xive_spapr_init
+    - powerpc/fsl_rio: Fix refcount leak in fsl_rio_setup
+    - mfd: davinci_voicecodec: Fix possible null-ptr-deref davinci_vc_probe()
+    - nfsd: destroy percpu stats counters after reply cache shutdown
+    - mailbox: forward the hrtimer if not queued and under a lock
+    - RDMA/hfi1: Prevent use of lock before it is initialized
+    - KVM: LAPIC: Drop pending LAPIC timer injection when canceling the timer
+    - Input: stmfts - do not leave device disabled in stmfts_input_open
+    - OPP: call of_node_put() on error path in _bandwidth_supported()
+    - f2fs: support fault injection for dquot_initialize()
+    - f2fs: fix to do sanity check on inline_dots inode
+    - f2fs: fix dereference of stale list iterator after loop body
+    - iommu/amd: Enable swiotlb in all cases
+    - iommu/mediatek: Fix 2 HW sharing pgtable issue
+    - iommu/mediatek: Add list_del in mtk_iommu_remove
+    - iommu/mediatek: Remove clk_disable in mtk_iommu_remove
+    - iommu/mediatek: Add mutex for m4u_group and m4u_dom in data
+    - i2c: at91: use dma safe buffers
+    - cpufreq: mediatek: Use module_init and add module_exit
+    - cpufreq: mediatek: Unregister platform device on exit
+    - iommu/arm-smmu-v3-sva: Fix mm use-after-free
+    - MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
+    - iommu/mediatek: Fix NULL pointer dereference when printing dev_name
+    - i2c: at91: Initialize dma_buf in at91_twi_xfer()
+    - dmaengine: idxd: Fix the error handling path in idxd_cdev_register()
+    - NFS: Do not report EINTR/ERESTARTSYS as mapping errors
+    - NFS: fsync() should report filesystem errors over EINTR/ERESTARTSYS
+    - NFS: Don't report ENOSPC write errors twice
+    - NFS: Do not report flush errors in nfs_write_end()
+    - NFS: Don't report errors from nfs_pageio_complete() more than once
+    - NFSv4/pNFS: Do not fail I/O when we fail to allocate the pNFS layout
+    - NFS: Further fixes to the writeback error handling
+    - video: fbdev: clcdfb: Fix refcount leak in clcdfb_of_vram_setup
+    - dmaengine: stm32-mdma: remove GISR1 register
+    - dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
+    - iommu/amd: Increase timeout waiting for GA log enablement
+    - i2c: npcm: Fix timeout calculation
+    - i2c: npcm: Correct register access width
+    - i2c: npcm: Handle spurious interrupts
+    - i2c: rcar: fix PM ref counts in probe error paths
+    - perf build: Fix btf__load_from_kernel_by_id() feature check
+    - perf c2c: Use stdio interface if slang is not supported
+    - perf jevents: Fix event syntax error caused by ExtSel
+    - video: fbdev: vesafb: Fix a use-after-free due early fb_info cleanup
+    - NFS: Always initialise fattr->label in nfs_fattr_alloc()
+    - NFS: Create a new nfs_alloc_fattr_with_label() function
+    - NFS: Convert GFP_NOFS to GFP_KERNEL
+    - NFSv4.1 mark qualified async operations as MOVEABLE tasks
+    - f2fs: fix to avoid f2fs_bug_on() in dec_valid_node_count()
+    - f2fs: fix to do sanity check on block address in f2fs_do_zero_range()
+    - f2fs: fix to clear dirty inode in f2fs_evict_inode()
+    - f2fs: fix deadloop in foreground GC
+    - f2fs: don't need inode lock for system hidden quota
+    - f2fs: fix to do sanity check on total_data_blocks
+    - f2fs: don't use casefolded comparison for "." and ".."
+    - f2fs: fix fallocate to use file_modified to update permissions consistently
+    - f2fs: fix to do sanity check for inline inode
+    - wifi: mac80211: fix use-after-free in chanctx code
+    - iwlwifi: mvm: fix assert 1F04 upon reconfig
+    - fs-writeback: writeback_sb_inodes：Recalculate 'wrote' according skipped
+      pages
+    - efi: Do not import certificates from UEFI Secure Boot for T2 Macs
+    - bfq: Avoid false marking of bic as stably merged
+    - bfq: Avoid merging queues with different parents
+    - bfq: Split shared queues on move between cgroups
+    - bfq: Update cgroup information before merging bio
+    - bfq: Drop pointless unlock-lock pair
+    - bfq: Remove pointless bfq_init_rq() calls
+    - bfq: Track whether bfq_group is still online
+    - bfq: Get rid of __bio_blkcg() usage
+    - bfq: Make sure bfqg for which we are queueing requests is online
+    - ext4: mark group as trimmed only if it was fully scanned
+    - ext4: fix use-after-free in ext4_rename_dir_prepare
+    - ext4: fix race condition between ext4_write and ext4_convert_inline_data
+    - ext4: fix warning in ext4_handle_inode_extension
+    - ext4: fix bug_on in ext4_writepages
+    - ext4: filter out EXT4_FC_REPLAY from on-disk superblock field s_state
+    - ext4: fix bug_on in __es_tree_search
+    - ext4: verify dir block before splitting it
+    - ext4: avoid cycles in directory h-tree
+    - ACPI: property: Release subnode properties with data nodes
+    - tty: goldfish: Introduce gf_ioread32()/gf_iowrite32()
+    - tracing: Fix potential double free in create_var_ref()
+    - tracing: Initialize integer variable to prevent garbage return value
+    - drm/amdgpu: add beige goby PCI ID
+    - PCI/PM: Fix bridge_d3_blacklist[] Elo i2 overwrite of Gigabyte X299
+    - PCI: qcom: Fix runtime PM imbalance on probe errors
+    - PCI: qcom: Fix unbalanced PHY init on probe errors
+    - staging: r8188eu: prevent ->Ssid overflow in rtw_wx_set_scan()
+    - mm, compaction: fast_find_migrateblock() should return pfn in the target
+      zone
+    - s390/perf: obtain sie_block from the right address
+    - s390/stp: clock_delta should be signed
+    - dlm: fix plock invalid read
+    - dlm: uninitialized variable on error in dlm_listen_for_all()
+    - dlm: fix missing lkb refcount handling
+    - ocfs2: dlmfs: fix error handling of user_dlm_destroy_lock
+    - scsi: dc395x: Fix a missing check on list iterator
+    - scsi: ufs: qcom: Add a readl() to make sure ref_clk gets enabled
+    - landlock: Add clang-format exceptions
+    - landlock: Format with clang-format
+    - selftests/landlock: Add clang-format exceptions
+    - selftests/landlock: Normalize array assignment
+    - selftests/landlock: Format with clang-format
+    - samples/landlock: Add clang-format exceptions
+    - samples/landlock: Format with clang-format
+    - landlock: Fix landlock_add_rule(2) documentation
+    - selftests/landlock: Make tests build with old libc
+    - selftests/landlock: Extend tests for minimal valid attribute size
+    - selftests/landlock: Add tests for unknown access rights
+    - selftests/landlock: Extend access right tests to directories
+    - selftests/landlock: Fully test file rename with "remove" access
+    - selftests/landlock: Add tests for O_PATH
+    - landlock: Change landlock_add_rule(2) argument check ordering
+    - landlock: Change landlock_restrict_self(2) check ordering
+    - selftests/landlock: Test landlock_create_ruleset(2) argument check ordering
+    - landlock: Define access_mask_t to enforce a consistent access mask size
+    - landlock: Reduce the maximum number of layers to 16
+    - landlock: Create find_rule() from unmask_layers()
+    - landlock: Fix same-layer rule unions
+    - drm/amdgpu/cs: make commands with 0 chunks illegal behaviour.
+    - drm/nouveau/subdev/bus: Ratelimit logging for fault errors
+    - drm/etnaviv: check for reaped mapping in etnaviv_iommu_unmap_gem
+    - drm/nouveau/clk: Fix an incorrect NULL check on list iterator
+    - drm/nouveau/kms/nv50-: atom: fix an incorrect NULL check on list iterator
+    - drm/bridge: analogix_dp: Grab runtime PM reference for DP-AUX
+    - drm/i915/dsi: fix VBT send packet port selection for ICL+
+    - md: fix an incorrect NULL check in does_sb_need_changing
+    - md: fix an incorrect NULL check in md_reload_sb
+    - mtd: cfi_cmdset_0002: Move and rename
+      chip_check/chip_ready/chip_good_for_write
+    - mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
+    - media: coda: Fix reported H264 profile
+    - media: coda: Add more H264 levels for CODA960
+    - ima: remove the IMA_TEMPLATE Kconfig option
+    - [Config] updateconfigs for IMA_TEMPLATE
+    - Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug
+    - RDMA/hfi1: Fix potential integer multiplication overflow errors
+    - mmc: core: Allows to override the timeout value for ioctl() path
+    - csky: patch_text: Fixup last cpu should be master
+    - irqchip/armada-370-xp: Do not touch Performance Counter Overflow on A375,
+      A38x, A39x
+    - irqchip: irq-xtensa-mx: fix initial IRQ affinity
+    - thermal: devfreq_cooling: use local ops instead of global ops
+    - cfg80211: declare MODULE_FIRMWARE for regulatory.db
+    - mac80211: upgrade passive scan to active scan on DFS channels after beacon
+      rx
+    - um: Use asm-generic/dma-mapping.h
+    - um: chan_user: Fix winch_tramp() return value
+    - um: Fix out-of-bounds read in LDT setup
+    - kexec_file: drop weak attribute from arch_kexec_apply_relocations[_add]
+    - ftrace: Clean up hash direct_functions on register failures
+    - ksmbd: fix outstanding credits related bugs
+    - iommu/msm: Fix an incorrect NULL check on list iterator
+    - iommu/dma: Fix iova map result check bug
+    - Revert "mm/cma.c: remove redundant cma_mutex lock"
+    - mm/page_alloc: always attempt to allocate at least one page during bulk
+      allocation
+    - nodemask.h: fix compilation error with GCC12
+    - hugetlb: fix huge_pmd_unshare address update
+    - mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
+    - xtensa/simdisk: fix proc_read_simdisk()
+    - rtl818x: Prevent using not initialized queues
+    - ASoC: rt5514: Fix event generation for "DSP Voice Wake Up" control
+    - carl9170: tx: fix an incorrect use of list iterator
+    - stm: ltdc: fix two incorrect NULL checks on list iterator
+    - bcache: remove incremental dirty sector counting for
+      bch_sectors_dirty_init()
+    - bcache: avoid journal no-space deadlock by reserving 1 journal bucket
+    - serial: pch: don't overwrite xmit->buf[0] by x_char
+    - tilcdc: tilcdc_external: fix an incorrect NULL check on list iterator
+    - gma500: fix an incorrect NULL check on list iterator
+    - arm64: dts: qcom: ipq8074: fix the sleep clock frequency
+    - arm64: tegra: Add missing DFLL reset on Tegra210
+    - clk: tegra: Add missing reset deassertion
+    - phy: qcom-qmp: fix struct clk leak on probe errors
+    - ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
+    - ARM: pxa: maybe fix gpio lookup tables
+    - SMB3: EBADF/EIO errors in rename/open caused by race condition in
+      smb2_compound_op
+    - docs/conf.py: Cope with removal of language=None in Sphinx 5.0.0
+    - dt-bindings: gpio: altera: correct interrupt-cells
+    - vdpasim: allow to enable a vq repeatedly
+    - blk-iolatency: Fix inflight count imbalances and IO hangs on offline
+    - coresight: core: Fix coresight device probe failure issue
+    - phy: qcom-qmp: fix reset-controller leak on probe errors
+    - net: ipa: fix page free in ipa_endpoint_trans_release()
+    - net: ipa: fix page free in ipa_endpoint_replenish_one()
+    - kseltest/cgroup: Make test_stress.sh work if run interactively
+    - list: test: Add a test for list_is_head()
+    - staging: r8188eu: delete rtw_wx_read/write32()
+    - RDMA/hns: Remove the num_cqc_timer variable
+    - RDMA/rxe: Generate a completion for unsupported/invalid opcode
+    - MIPS: IP27: Remove incorrect `cpu_has_fpu' override
+    - MIPS: IP30: Remove incorrect `cpu_has_fpu' override
+    - ext4: only allow test_dummy_encryption when supported
+    - interconnect: qcom: sc7180: Drop IP0 interconnects
+    - interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate
+    - fs: add two trivial lookup helpers
+    - exportfs: support idmapped mounts
+    - fs/ntfs3: Fix invalid free in log_replay
+    - md: Don't set mddev private to NULL in raid0 pers->free
+    - md: fix double free of io_acct_set bioset
+    - md: bcache: check the return value of kzalloc() in detached_dev_do_request()
+    - pinctrl/rockchip: support setting input-enable param
+    - block: fix bio_clone_blkg_association() to associate with proper blkcg_gq
+    - Linux 5.15.46
+  * [SRU] bcache deadlock during read IO in writeback mode (LP: #1980925) //
+    Jammy update: v5.15.46 upstream stable release (LP: #1981864)
+    - bcache: improve multithreaded bch_btree_check()
+    - bcache: improve multithreaded bch_sectors_dirty_init()
+  * Jammy update: v5.15.45 upstream stable release (LP: #1981862)
+    - ALSA: usb-audio: Don't get sample rate for MCT Trigger 5 USB-to-HDMI
+    - pinctrl: sunxi: fix f1c100s uart2 function
+    - KVM: arm64: Don't hypercall before EL2 init
+    - percpu_ref_init(): clean ->percpu_count_ref on failure
+    - net: af_key: check encryption module availability consistency
+    - nfc: pn533: Fix buggy cleanup order
+    - net: ftgmac100: Disable hardware checksum on AST2600
+    - i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging
+    - drivers: i2c: thunderx: Allow driver to work with ACPI defined TWSI
+      controllers
+    - i2c: ismt: prevent memory corruption in ismt_access()
+    - assoc_array: Fix BUG_ON during garbage collect
+    - pipe: make poll_usage boolean and annotate its access
+    - pipe: Fix missing lock in pipe_resize_ring()
+    - net: ipa: compute proper aggregation limit
+    - drm/i915: Fix -Wstringop-overflow warning in call to intel_read_wm_latency()
+    - exfat: check if cluster num is valid
+    - lib/crypto: add prompts back to crypto libraries
+    - crypto: drbg - prepare for more fine-grained tracking of seeding state
+    - crypto: drbg - track whether DRBG was seeded with !rng_is_initialized()
+    - crypto: drbg - move dynamic ->reseed_threshold adjustments to __drbg_seed()
+    - crypto: drbg - make reseeding from get_random_bytes() synchronous
+    - netfilter: nf_tables: hold mutex on netns pre_exit path
+    - netfilter: nf_tables: double hook unregistration in netns path
+    - netfilter: conntrack: re-fetch conntrack after insertion
+    - KVM: PPC: Book3S HV: fix incorrect NULL check on list iterator
+    - x86/kvm: Alloc dummy async #PF token outside of raw spinlock
+    - x86, kvm: use correct GFP flags for preemption disabled
+    - KVM: x86: avoid calling x86 emulator without a decoded instruction
+    - KVM: x86: Drop WARNs that assert a triple fault never "escapes" from L2
+    - KVM: SVM: Use kzalloc for sev ioctl interfaces to prevent kernel data leak
+    - crypto: caam - fix i.MX6SX entropy delay value
+    - crypto: ecrdsa - Fix incorrect use of vli_cmp
+    - zsmalloc: fix races between asynchronous zspage free and page migration
+    - ALSA: usb-audio: Workaround for clock setup on TEAC devices
+    - ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
+    - ALSA: usb-audio: Configure sync endpoints before data
+    - Bluetooth: hci_qca: Use del_timer_sync() before freeing
+    - ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
+    - dm integrity: fix error code in dm_integrity_ctr()
+    - dm crypt: make printing of the key constant-time
+    - dm stats: add cond_resched when looping over entries
+    - dm verity: set DM_TARGET_IMMUTABLE feature flag
+    - raid5: introduce MD_BROKEN
+    - fs/ntfs3: validate BOOT sectors_per_clusters
+    - HID: multitouch: Add support for Google Whiskers Touchpad
+    - HID: multitouch: add quirks to enable Lenovo X12 trackpoint
+    - x86/sgx: Disconnect backing page references from dirty status
+    - x86/sgx: Mark PCMD page as dirty when modifying contents
+    - x86/sgx: Obtain backing storage page with enclave mutex held
+    - x86/sgx: Fix race between reclaimer and page fault handler
+    - x86/sgx: Ensure no data in PCMD page after truncate
+    - media: i2c: imx412: Fix reset GPIO polarity
+    - media: i2c: imx412: Fix power_off ordering
+    - tpm: Fix buffer access in tpm2_get_tpm_pt()
+    - tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()
+    - docs: submitting-patches: Fix crossref to 'The canonical patch format'
+    - NFS: Memory allocation failures are not server fatal errors
+    - NFSD: Fix possible sleep during nfsd4_release_lockowner()
+    - bpf: Fix potential array overflow in bpf_trampoline_get_progs()
+    - bpf: Enlarge offset check value to INT_MAX in bpf_skb_{load,store}_bytes
+    - bpf: Fix excessive memory allocation in stack_map_alloc()
+    - bpf: Reject writes for PTR_TO_MAP_KEY in check_helper_mem_access
+    - bpf: Check PTR_TO_MEM | MEM_RDONLY in check_helper_mem_access
+    - ALSA: usb-audio: Optimize TEAC clock quirk
+    - Linux 5.15.45
+  * Jammy update: v5.15.44 upstream stable release (LP: #1981649)
+    - Revert "UBUNTU: SAUCE: random: Make getrandom() ready earlier"
+    - ice: fix crash at allocation failure
+    - ACPI: sysfs: Fix BERT error region memory mapping
+    - MAINTAINERS: co-maintain random.c
+    - MAINTAINERS: add git tree for random.c
+    - lib/crypto: blake2s: include as built-in
+    - [Config] updateconfigs for CRYPTO_LIB_BLAKE2S
+    - lib/crypto: blake2s: move hmac construction into wireguard
+    - lib/crypto: sha1: re-roll loops to reduce code size
+    - lib/crypto: blake2s: avoid indirect calls to compression function for Clang
+      CFI
+    - random: document add_hwgenerator_randomness() with other input functions
+    - random: remove unused irq_flags argument from add_interrupt_randomness()
+    - random: use BLAKE2s instead of SHA1 in extraction
+    - random: do not sign extend bytes for rotation when mixing
+    - random: do not re-init if crng_reseed completes before primary init
+    - random: mix bootloader randomness into pool
+    - random: harmonize "crng init done" messages
+    - random: use IS_ENABLED(CONFIG_NUMA) instead of ifdefs
+    - random: early initialization of ChaCha constants
+    - random: avoid superfluous call to RDRAND in CRNG extraction
+    - random: don't reset crng_init_cnt on urandom_read()
+    - random: fix typo in comments
+    - random: cleanup poolinfo abstraction
+    - random: cleanup integer types
+    - random: remove incomplete last_data logic
+    - random: remove unused extract_entropy() reserved argument
+    - random: rather than entropy_store abstraction, use global
+    - random: remove unused OUTPUT_POOL constants
+    - random: de-duplicate INPUT_POOL constants
+    - random: prepend remaining pool constants with POOL_
+    - random: cleanup fractional entropy shift constants
+    - random: access input_pool_data directly rather than through pointer
+    - random: selectively clang-format where it makes sense
+    - random: simplify arithmetic function flow in account()
+    - random: continually use hwgenerator randomness
+    - random: access primary_pool directly rather than through pointer
+    - random: only call crng_finalize_init() for primary_crng
+    - random: use computational hash for entropy extraction
+    - random: simplify entropy debiting
+    - random: use linear min-entropy accumulation crediting
+    - random: always wake up entropy writers after extraction
+    - random: make credit_entropy_bits() always safe
+    - random: remove use_input_pool parameter from crng_reseed()
+    - random: remove batched entropy locking
+    - random: fix locking in crng_fast_load()
+    - random: use RDSEED instead of RDRAND in entropy extraction
+    - random: get rid of secondary crngs
+    - random: inline leaves of rand_initialize()
+    - random: ensure early RDSEED goes through mixer on init
+    - random: do not xor RDRAND when writing into /dev/random
+    - random: absorb fast pool into input pool after fast load
+    - random: use simpler fast key erasure flow on per-cpu keys
+    - random: use hash function for crng_slow_load()
+    - random: make more consistent use of integer types
+    - random: remove outdated INT_MAX >> 6 check in urandom_read()
+    - random: zero buffer after reading entropy from userspace
+    - random: fix locking for crng_init in crng_reseed()
+    - random: tie batched entropy generation to base_crng generation
+    - random: remove ifdef'd out interrupt bench
+    - random: remove unused tracepoints
+    - random: add proper SPDX header
+    - random: deobfuscate irq u32/u64 contributions
+    - random: introduce drain_entropy() helper to declutter crng_reseed()
+    - random: remove useless header comment
+    - random: remove whitespace and reorder includes
+    - random: group initialization wait functions
+    - random: group crng functions
+    - random: group entropy extraction functions
+    - random: group entropy collection functions
+    - random: group userspace read/write functions
+    - random: group sysctl functions
+    - random: rewrite header introductory comment
+    - random: defer fast pool mixing to worker
+    - random: do not take pool spinlock at boot
+    - random: unify early init crng load accounting
+    - random: check for crng_init == 0 in add_device_randomness()
+    - random: pull add_hwgenerator_randomness() declaration into random.h
+    - random: clear fast pool, crng, and batches in cpuhp bring up
+    - random: round-robin registers as ulong, not u32
+    - random: only wake up writers after zap if threshold was passed
+    - random: cleanup UUID handling
+    - random: unify cycles_t and jiffies usage and types
+    - random: do crng pre-init loading in worker rather than irq
+    - random: give sysctl_random_min_urandom_seed a more sensible value
+    - random: don't let 644 read-only sysctls be written to
+    - random: replace custom notifier chain with standard one
+    - random: use SipHash as interrupt entropy accumulator
+    - random: make consistent usage of crng_ready()
+    - random: reseed more often immediately after booting
+    - random: check for signal and try earlier when generating entropy
+    - random: skip fast_init if hwrng provides large chunk of entropy
+    - random: treat bootloader trust toggle the same way as cpu trust toggle
+    - random: re-add removed comment about get_random_{u32,u64} reseeding
+    - random: mix build-time latent entropy into pool at init
+    - random: do not split fast init input in add_hwgenerator_randomness()
+    - random: do not allow user to keep crng key around on stack
+    - random: check for signal_pending() outside of need_resched() check
+    - random: check for signals every PAGE_SIZE chunk of /dev/[u]random
+    - random: allow partial reads if later user copies fail
+    - random: make random_get_entropy() return an unsigned long
+    - random: document crng_fast_key_erasure() destination possibility
+    - random: fix sysctl documentation nits
+    - init: call time_init() before rand_initialize()
+    - ia64: define get_cycles macro for arch-override
+    - s390: define get_cycles macro for arch-override
+    - parisc: define get_cycles macro for arch-override
+    - alpha: define get_cycles macro for arch-override
+    - powerpc: define get_cycles macro for arch-override
+    - timekeeping: Add raw clock fallback for random_get_entropy()
+    - m68k: use fallback for random_get_entropy() instead of zero
+    - riscv: use fallback for random_get_entropy() instead of zero
+    - mips: use fallback for random_get_entropy() instead of just c0 random
+    - arm: use fallback for random_get_entropy() instead of zero
+    - nios2: use fallback for random_get_entropy() instead of zero
+    - x86/tsc: Use fallback for random_get_entropy() instead of zero
+    - um: use fallback for random_get_entropy() instead of zero
+    - sparc: use fallback for random_get_entropy() instead of zero
+    - xtensa: use fallback for random_get_entropy() instead of zero
+    - random: insist on random_get_entropy() existing in order to simplify
+    - random: do not use batches when !crng_ready()
+    - random: use first 128 bits of input as fast init
+    - random: do not pretend to handle premature next security model
+    - random: order timer entropy functions below interrupt functions
+    - random: do not use input pool from hard IRQs
+    - random: help compiler out with fast_mix() by using simpler arguments
+    - siphash: use one source of truth for siphash permutations
+    - random: use symbolic constants for crng_init states
+    - random: avoid initializing twice in credit race
+    - random: move initialization out of reseeding hot path
+    - random: remove ratelimiting for in-kernel unseeded randomness
+    - random: use proper jiffies comparison macro
+    - random: handle latent entropy and command line from random_init()
+    - random: credit architectural init the exact amount
+    - random: use static branch for crng_ready()
+    - random: remove extern from functions in header
+    - random: use proper return types on get_random_{int,long}_wait()
+    - random: make consistent use of buf and len
+    - random: move initialization functions out of hot pages
+    - random: move randomize_page() into mm where it belongs
+    - random: unify batched entropy implementations
+    - random: convert to using fops->read_iter()
+    - random: convert to using fops->write_iter()
+    - random: wire up fops->splice_{read,write}_iter()
+    - random: check for signals after page of pool writes
+    - ALSA: ctxfi: Add SB046x PCI ID
+    - Linux 5.15.44
+    - Revert "random: use static branch for crng_ready()"
+  * Jammy update: v5.15.43 upstream stable release (LP: #1981468)
+    - mptcp: Do TCP fallback on early DSS checksum failure
+    - Linux 5.15.43
+  * Jammy update: v5.15.42 upstream stable release (LP: #1981375)
+    - usb: gadget: fix race when gadget driver register via ioctl
+    - io_uring: arm poll for non-nowait files
+    - kernel/resource: Introduce request_mem_region_muxed()
+    - i2c: piix4: Replace hardcoded memory map size with a #define
+    - i2c: piix4: Move port I/O region request/release code into functions
+    - i2c: piix4: Move SMBus controller base address detect into function
+    - i2c: piix4: Move SMBus port selection into function
+    - i2c: piix4: Add EFCH MMIO support to region request and release
+    - i2c: piix4: Add EFCH MMIO support to SMBus base address detect
+    - i2c: piix4: Add EFCH MMIO support for SMBus port select
+    - i2c: piix4: Enable EFCH MMIO for Family 17h+
+    - Watchdog: sp5100_tco: Move timer initialization into function
+    - Watchdog: sp5100_tco: Refactor MMIO base address initialization
+    - Watchdog: sp5100_tco: Add initialization using EFCH MMIO
+    - Watchdog: sp5100_tco: Enable Family 17h+ CPUs
+    - mm/kfence: reset PG_slab and memcg_data before freeing __kfence_pool
+    - Revert "drm/i915/opregion: check port number bounds for SWSCI display power
+      state"
+    - rtc: fix use-after-free on device removal
+    - rtc: pcf2127: fix bug when reading alarm registers
+    - um: Cleanup syscall_handler_t definition/cast, fix warning
+    - Input: add bounds checking to input_set_capability()
+    - Input: stmfts - fix reference leak in stmfts_input_open
+    - nvme-pci: add quirks for Samsung X5 SSDs
+    - gfs2: Disable page faults during lockless buffered reads
+    - rtc: sun6i: Fix time overflow handling
+    - crypto: stm32 - fix reference leak in stm32_crc_remove
+    - crypto: x86/chacha20 - Avoid spurious jumps to other functions
+    - s390/traps: improve panic message for translation-specification exception
+    - s390/pci: improve zpci_dev reference counting
+    - vhost_vdpa: don't setup irq offloading when irq_num < 0
+    - tools/virtio: compile with -pthread
+    - nvmet: use a private workqueue instead of the system workqueue
+    - nvme-multipath: fix hang when disk goes live over reconnect
+    - rtc: mc146818-lib: Fix the AltCentury for AMD platforms
+    - fs: fix an infinite loop in iomap_fiemap
+    - MIPS: lantiq: check the return value of kzalloc()
+    - drbd: remove usage of list iterator variable after loop
+    - platform/chrome: cros_ec_debugfs: detach log reader wq from devm
+    - ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
+    - nilfs2: fix lockdep warnings in page operations for btree nodes
+    - nilfs2: fix lockdep warnings during disk space reclamation
+    - ALSA: usb-audio: Restore Rane SL-1 quirk
+    - ALSA: wavefront: Proper check of get_user() error
+    - ALSA: hda/realtek: Add quirk for TongFang devices with pop noise
+    - perf: Fix sys_perf_event_open() race against self
+    - selinux: fix bad cleanup on error in hashtab_duplicate()
+    - Fix double fget() in vhost_net_set_backend()
+    - PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
+    - Revert "can: m_can: pci: use custom bit timings for Elkhart Lake"
+    - KVM: x86/mmu: Update number of zapped pages even if page list is stable
+    - arm64: paravirt: Use RCU read locks to guard stolen_time
+    - arm64: mte: Ensure the cleared tags are visible before setting the PTE
+    - crypto: qcom-rng - fix infinite loop on requests not multiple of WORD_SZ
+    - libceph: fix potential use-after-free on linger ping and resends
+    - drm/i915/dmc: Add MMIO range restrictions
+    - drm/dp/mst: fix a possible memory leak in fetch_monitor_name()
+    - dma-buf: fix use of DMA_BUF_SET_NAME_{A,B} in userspace
+    - dma-buf: ensure unique directory name for dmabuf stats
+    - ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi
+    - pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl
+    - ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group
+    - ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
+    - ARM: dts: aspeed: Add secure boot controller node
+    - ARM: dts: aspeed: Add video engine to g6
+    - pinctrl: mediatek: mt8365: fix IES control pins
+    - ALSA: hda - fix unused Realtek function when PM is not enabled
+    - net: ipa: record proper RX transaction count
+    - net: macb: Increment rx bd head after allocating skb and buffer
+    - xfrm: rework default policy structure
+    - xfrm: fix "disable_policy" flag use when arriving from different devices
+    - net/sched: act_pedit: sanitize shift argument before usage
+    - netfilter: flowtable: fix excessive hw offload attempts after failure
+    - netfilter: nft_flow_offload: skip dst neigh lookup for ppp devices
+    - net: fix dev_fill_forward_path with pppoe + bridge
+    - netfilter: nft_flow_offload: fix offload with pppoe + vlan
+    - net: systemport: Fix an error handling path in bcm_sysport_probe()
+    - net: vmxnet3: fix possible use-after-free bugs in vmxnet3_rq_alloc_rx_buf()
+    - net: vmxnet3: fix possible NULL pointer dereference in vmxnet3_rq_cleanup()
+    - ice: fix crash when writing timestamp on RX rings
+    - ice: fix possible under reporting of ethtool Tx and Rx statistics
+    - ice: move ice_container_type onto ice_ring_container
+    - ice: Fix interrupt moderation settings getting cleared
+    - clk: at91: generated: consider range when calculating best rate
+    - net/qla3xxx: Fix a test in ql_reset_work()
+    - NFC: nci: fix sleep in atomic context bugs caused by nci_skb_alloc
+    - net/mlx5: DR, Fix missing flow_source when creating multi-destination FW
+      table
+    - net/mlx5e: Properly block LRO when XDP is enabled
+    - ARM: 9196/1: spectre-bhb: enable for Cortex-A15
+    - ARM: 9197/1: spectre-bhb: fix loop8 sequence for Thumb2
+    - mptcp: change the parameter of __mptcp_make_csum
+    - mptcp: reuse __mptcp_make_csum in validate_data_csum
+    - mptcp: fix checksum byte order
+    - igb: skip phy status check where unavailable
+    - netfilter: flowtable: fix TCP flow teardown
+    - netfilter: flowtable: pass flowtable to nf_flow_table_iterate()
+    - netfilter: flowtable: move dst_check to packet path
+    - net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
+    - riscv: dts: sifive: fu540-c000: align dma node name with dtschema
+    - scsi: ufs: core: Fix referencing invalid rsp field
+    - perf build: Fix check for btf__load_from_kernel_by_id() in libbpf
+    - gpio: gpio-vf610: do not touch other bits when set the target bit
+    - gpio: mvebu/pwm: Refuse requests with inverted polarity
+    - perf regs x86: Fix arch__intr_reg_mask() for the hybrid platform
+    - perf bench numa: Address compiler error on s390
+    - scsi: scsi_dh_alua: Properly handle the ALUA transitioning state
+    - scsi: qla2xxx: Fix missed DMA unmap for aborted commands
+    - mac80211: fix rx reordering with non explicit / psmp ack policy
+    - nl80211: validate S1G channel width
+    - selftests: add ping test with ping_group_range tuned
+    - fbdev: Prevent possible use-after-free in fb_release()
+    - net: fix wrong network header length
+    - nl80211: fix locking in nl80211_set_tx_bitrate_mask()
+    - ethernet: tulip: fix missing pci_disable_device() on error in
+      tulip_init_one()
+    - net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()
+    - net: atlantic: fix "frag[0] not initialized"
+    - net: atlantic: reduce scope of is_rsc_complete
+    - net: atlantic: add check for MAX_SKB_FRAGS
+    - net: atlantic: verify hw_head_ lies within TX buffer ring
+    - arm64: Enable repeat tlbi workaround on KRYO4XX gold CPUs
+    - Input: ili210x - fix reset timing
+    - dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group
+    - i2c: mt7621: fix missing clk_disable_unprepare() on error in mtk_i2c_probe()
+    - afs: Fix afs_getattr() to refetch file status if callback break occurred
+    - Linux 5.15.42
+  * CVE-2021-33061
+    - ixgbe: add the ability for the PF to disable VF link state
+    - ixgbe: add improvement for MDD response functionality
+    - ixgbevf: add disable link state
+  * Fix PSR flickers on Intel TGL laptops + AUO panel (LP: #1980087)
+    - SAUCE: drm/i915/display/psr: Fix flicker on TGL + AUO panel
+  * Fix audio on Zbook Studio G9  (LP: #1966010)
+    - ALSA: hda/realtek: Fix LED on Zbook Studio G9
+  * Support Cirrus audio codec configurations for Odin platform (LP: #1968861)
+    - ALSA: hda/cs8409: Support new Odin Variants
+    - ALSA: hda/cs8409: Add Speaker Playback Switch for Cyborg
+  * Fix beacon loss for rtl8821ce on certain platforms (LP: #1969771)
+    - rtw88: pci: 8821c: Disable 21ce completion timeout
+  * Suppress harmless warning from hp-wmi (LP: #1980307)
+    - platform/x86: hp-wmi: Ignore Sanitization Mode event
+  * Fix headset mic no sound on an HP desktop (LP: #1978925)
+    - ALSA: hda/realtek - ALC897 headset MIC no sound
+  * alsa/hda: mute led can't work on the lenovo machine with cs35l41 s-codec
+    (LP: #1978915)
+    - ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec
+  * Jammy update: v5.15.41 upstream stable release (LP: #1980278)
+    - batman-adv: Don't skb_split skbuffs with frag_list
+    - iwlwifi: iwl-dbg: Use del_timer_sync() before freeing
+    - hwmon: (tmp401) Add OF device ID table
+    - mac80211: Reset MBSSID parameters upon connection
+    - net: Fix features skip in for_each_netdev_feature()
+    - net: mscc: ocelot: fix last VCAP IS1/IS2 filter persisting in hardware when
+      deleted
+    - net: mscc: ocelot: fix VCAP IS2 filters matching on both lookups
+    - net: mscc: ocelot: restrict tc-trap actions to VCAP IS2 lookup 0
+    - net: mscc: ocelot: avoid corrupting hardware counters when moving VCAP
+      filters
+    - fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
+    - fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
+    - fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
+    - platform/surface: aggregator: Fix initialization order when compiling as
+      builtin module
+    - ice: Fix race during aux device (un)plugging
+    - ice: fix PTP stale Tx timestamps cleanup
+    - ipv4: drop dst in multicast routing path
+    - drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
+    - netlink: do not reset transport header in netlink_recvmsg()
+    - net: chelsio: cxgb4: Avoid potential negative array offset
+    - fbdev: efifb: Fix a use-after-free due early fb_info cleanup
+    - sfc: Use swap() instead of open coding it
+    - net: sfc: fix memory leak due to ptp channel
+    - mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protection
+    - nfs: fix broken handling of the softreval mount option
+    - ionic: fix missing pci_release_regions() on error in ionic_probe()
+    - dim: initialize all struct fields
+    - hwmon: (ltq-cputemp) restrict it to SOC_XWAY
+    - procfs: prevent unprivileged processes accessing fdinfo dir
+    - selftests: vm: Makefile: rename TARGETS to VMTARGETS
+    - arm64: vdso: fix makefile dependency on vdso.so
+    - virtio: fix virtio transitional ids
+    - s390/ctcm: fix variable dereferenced before check
+    - s390/ctcm: fix potential memory leak
+    - s390/lcs: fix variable dereferenced before check
+    - net/sched: act_pedit: really ensure the skb is writable
+    - net: ethernet: mediatek: ppe: fix wrong size passed to memset()
+    - net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral
+    - drm/vc4: hdmi: Fix build error for implicit function declaration
+    - net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
+    - net/smc: non blocking recvmsg() return -EAGAIN when no data and
+      signal_pending
+    - net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
+    - tls: Fix context leak on tls_device_down
+    - drm/vmwgfx: Fix fencing on SVGAv3
+    - gfs2: Fix filesystem block deallocation for short writes
+    - hwmon: (f71882fg) Fix negative temperature
+    - RDMA/irdma: Fix deadlock in irdma_cleanup_cm_core()
+    - iommu: arm-smmu: disable large page mappings for Nvidia arm-smmu
+    - ASoC: max98090: Reject invalid values in custom control put()
+    - ASoC: max98090: Generate notifications on changes for custom control
+    - ASoC: ops: Validate input values in snd_soc_put_volsw_range()
+    - s390: disable -Warray-bounds
+    - ASoC: SOF: Fix NULL pointer exception in sof_pci_probe callback
+    - net: emaclite: Don't advertise 1000BASE-T and do auto negotiation
+    - net: sfp: Add tx-fault workaround for Huawei MA5671A SFP ONT
+    - secure_seq: use the 64 bits of the siphash for port offset calculation
+    - tcp: use different parts of the port_offset for index and offset
+    - tcp: resalt the secret every 10 seconds
+    - tcp: add small random increments to the source port
+    - tcp: dynamically allocate the perturb table used by source ports
+    - tcp: increase source port perturb table to 2^16
+    - tcp: drop the hash_32() part from the index calculation
+    - interconnect: Restore sync state by ignoring ipa-virt in provider count
+    - firmware_loader: use kernel credentials when reading firmware
+    - KVM: PPC: Book3S PR: Enable MSR_DR for switch_mmu_context()
+    - usb: xhci-mtk: fix fs isoc's transfer error
+    - x86/mm: Fix marking of unused sub-pmd ranges
+    - tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
+    - tty: n_gsm: fix buffer over-read in gsm_dlci_data()
+    - tty: n_gsm: fix mux activation issues in gsm_config()
+    - usb: cdc-wdm: fix reading stuck on device close
+    - usb: typec: tcpci: Don't skip cleanup in .remove() on error
+    - usb: typec: tcpci_mt6360: Update for BMC PHY setting
+    - USB: serial: pl2303: add device id for HP LM930 Display
+    - USB: serial: qcserial: add support for Sierra Wireless EM7590
+    - USB: serial: option: add Fibocom L610 modem
+    - USB: serial: option: add Fibocom MA510 modem
+    - slimbus: qcom: Fix IRQ check in qcom_slim_probe
+    - fsl_lpuart: Don't enable interrupts too early
+    - serial: 8250_mtk: Fix UART_EFR register address
+    - serial: 8250_mtk: Fix register address for XON/XOFF character
+    - ceph: fix setting of xattrs on async created inodes
+    - Revert "mm/memory-failure.c: skip huge_zero_page in memory_failure()"
+    - mm/huge_memory: do not overkill when splitting huge_zero_page
+    - drm/vmwgfx: Disable command buffers on svga3 without gbobjects
+    - drm/nouveau/tegra: Stop using iommu_present()
+    - i40e: i40e_main: fix a missing check on list iterator
+    - net: atlantic: always deep reset on pm op, fixing up my null deref
+      regression
+    - net: phy: Fix race condition on link status change
+    - writeback: Avoid skipping inode writeback
+    - cgroup/cpuset: Remove cpus_allowed/mems_allowed setup in cpuset_init_smp()
+    - arm[64]/memremap: don't abuse pfn_valid() to ensure presence of linear map
+    - net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061
+    - net: phy: micrel: Pass .probe for KS8737
+    - SUNRPC: Ensure that the gssproxy client can start in a connected state
+    - drm/vmwgfx: Initialize drm_mode_fb_cmd2
+    - dma-buf: call dma_buf_stats_setup after dmabuf is in valid list
+    - mm/hwpoison: use pr_err() instead of dump_page() in get_any_page()
+    - ping: fix address binding wrt vrf
+    - usb: gadget: uvc: rename function to be more consistent
+    - usb: gadget: uvc: allow for application to cleanly shutdown
+    - Linux 5.15.41
+  * Jammy update: v5.15.40 upstream stable release (LP: #1980277)
+    - tools arch: Update arch/x86/lib/mem{cpy,set}_64.S copies used in 'perf bench
+      mem memcpy'
+    - Bluetooth: Fix the creation of hdev->name
+    - udf: Avoid using stale lengthOfImpUse
+    - mm: fix missing cache flush for all tail pages of compound page
+    - mm: hugetlb: fix missing cache flush in copy_huge_page_from_user()
+    - mm: shmem: fix missing cache flush in shmem_mfill_atomic_pte()
+    - mm: userfaultfd: fix missing cache flush in mcopy_atomic_pte() and
+      __mcopy_atomic()
+    - mm/hwpoison: fix error page recovered but reported "not recovered"
+    - mm/mlock: fix potential imbalanced rlimit ucounts adjustment
+    - mm: fix invalid page pointer returned with FOLL_PIN gups
+    - Linux 5.15.40
+
+  [ Ubuntu: 5.15.0-46.49 ]
+
+  * CVE-2022-2585
+    - SAUCE: posix-cpu-timers: Cleanup CPU timers before freeing them during exec
+  * CVE-2022-2586
+    - SAUCE: netfilter: nf_tables: do not allow SET_ID to refer to another table
+    - SAUCE: netfilter: nf_tables: do not allow CHAIN_ID to refer to another table
+    - SAUCE: netfilter: nf_tables: do not allow RULE_ID to refer to another chain
+  * CVE-2022-2588
+    - SAUCE: net_sched: cls_route: remove from list when handle is 0
+
+  [ Ubuntu: 5.15.0-45.48 ]
+
+  * CVE-2022-29900 // CVE-2022-29901
+    - x86/lib/atomic64_386_32: Rename things
+    - x86: Prepare asm files for straight-line-speculation
+    - x86: Prepare inline-asm for straight-line-speculation
+    - x86/alternative: Relax text_poke_bp() constraint
+    - kbuild: move objtool_args back to scripts/Makefile.build
+    - x86: Add straight-line-speculation mitigation
+    - kvm/emulate: Fix SETcc emulation function offsets with SLS
+    - crypto: x86/poly1305 - Fixup SLS
+    - objtool: Add straight-line-speculation validation
+    - objtool: Fix SLS validation for kcov tail-call replacement
+    - objtool: Fix objtool regression on x32 systems
+    - objtool: Fix symbol creation
+    - objtool: Introduce CFI hash
+    - objtool: Default ignore INT3 for unreachable
+    - x86, kvm: use proper ASM macros for kvm_vcpu_is_preempted
+    - x86/traps: Use pt_regs directly in fixup_bad_iret()
+    - x86/entry: Switch the stack after error_entry() returns
+    - x86/entry: Move PUSH_AND_CLEAR_REGS out of error_entry()
+    - x86/entry: Don't call error_entry() for XENPV
+    - x86/entry: Remove skip_r11rcx
+    - x86/realmode: build with -D__DISABLE_EXPORTS
+    - x86/ibt,ftrace: Make function-graph play nice
+    - x86/kvm/vmx: Make noinstr clean
+    - x86/cpufeatures: Move RETPOLINE flags to word 11
+    - x86/retpoline: Cleanup some #ifdefery
+    - x86/retpoline: Swizzle retpoline thunk
+    - x86/retpoline: Use -mfunction-return
+    - x86: Undo return-thunk damage
+    - x86,objtool: Create .return_sites
+    - objtool: skip non-text sections when adding return-thunk sites
+    - x86,static_call: Use alternative RET encoding
+    - x86/ftrace: Use alternative RET encoding
+    - x86/bpf: Use alternative RET encoding
+    - x86/kvm: Fix SETcc emulation for return thunks
+    - x86/vsyscall_emu/64: Don't use RET in vsyscall emulation
+    - x86/sev: Avoid using __x86_return_thunk
+    - x86: Use return-thunk in asm code
+    - x86/entry: Avoid very early RET
+    - objtool: Treat .text.__x86.* as noinstr
+    - x86: Add magic AMD return-thunk
+    - x86/bugs: Report AMD retbleed vulnerability
+    - x86/bugs: Add AMD retbleed= boot parameter
+    - x86/bugs: Enable STIBP for JMP2RET
+    - x86/bugs: Keep a per-CPU IA32_SPEC_CTRL value
+    - x86/entry: Add kernel IBRS implementation
+    - x86/bugs: Optimize SPEC_CTRL MSR writes
+    - x86/speculation: Add spectre_v2=ibrs option to support Kernel IBRS
+    - x86/bugs: Split spectre_v2_select_mitigation() and
+      spectre_v2_user_select_mitigation()
+    - x86/bugs: Report Intel retbleed vulnerability
+    - intel_idle: Disable IBRS during long idle
+    - objtool: Update Retpoline validation
+    - x86/xen: Rename SYS* entry points
+    - x86/xen: Add UNTRAIN_RET
+    - x86/bugs: Add retbleed=ibpb
+    - x86/bugs: Do IBPB fallback check only once
+    - objtool: Add entry UNRET validation
+    - x86/cpu/amd: Add Spectral Chicken
+    - x86/speculation: Fix RSB filling with CONFIG_RETPOLINE=n
+    - x86/speculation: Fix firmware entry SPEC_CTRL handling
+    - x86/speculation: Fix SPEC_CTRL write on SMT state change
+    - x86/speculation: Use cached host SPEC_CTRL value for guest entry/exit
+    - x86/speculation: Remove x86_spec_ctrl_mask
+    - objtool: Re-add UNWIND_HINT_{SAVE_RESTORE}
+    - KVM: VMX: Flatten __vmx_vcpu_run()
+    - KVM: VMX: Convert launched argument to flags
+    - KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS
+    - KVM: VMX: Fix IBRS handling after vmexit
+    - x86/speculation: Fill RSB on vmexit for IBRS
+    - KVM: VMX: Prevent RSB underflow before vmenter
+    - x86/common: Stamp out the stepping madness
+    - x86/cpu/amd: Enumerate BTC_NO
+    - x86/retbleed: Add fine grained Kconfig knobs
+    - x86/bugs: Add Cannon lake to RETBleed affected CPU list
+    - x86/entry: Move PUSH_AND_CLEAR_REGS() back into error_entry
+    - x86/bugs: Do not enable IBPB-on-entry when IBPB is not supported
+    - x86/kexec: Disable RET on kexec
+    - x86/speculation: Disable RRSBA behavior
+    - [Config]: Enable speculation mitigations
+    - x86/static_call: Serialize __static_call_fixup() properly
+    - x86/asm/32: Fix ANNOTATE_UNRET_SAFE use on 32-bit
+    - x86/bugs: Mark retbleed_strings static
+    - x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
+    - x86/kvm: fix FASTOP_SIZE when return thunks are enabled
+    - x86/speculation: Use DECLARE_PER_CPU for x86_spec_ctrl_current
+    - KVM: emulate: do not adjust size of fastop and setcc subroutines
+    - x86/bugs: Remove apostrophe typo
+    - efi/x86: use naked RET on mixed mode call wrapper
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 19 Jan 2023 11:15:52 +1000
+
+linux-xilinx-zynqmp (5.15.0-1018.20) jammy; urgency=medium
+
+  * ProvenCore TEE driver causes process stall on systems without secure-OS
+    - Revert "Import ProveCore TEE driver"
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 15 Dec 2022 21:24:04 +1000
+
+linux-xilinx-zynqmp (5.15.0-1017.18) jammy; urgency=medium
+
+  * mv-camera-sensor-module updated driver
+    - Update Xilinx mv-camera-sensor-module kernel module
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 15 Dec 2022 09:10:24 +1000
+
+linux-xilinx-zynqmp (5.15.0-1016.17) jammy; urgency=medium
+
+  * Integrate ProvenCore TEE kernel driver
+    - Import ProveCore TEE driver
+
+  * Miscellaneous upstream changes
+    - arm64: zynqmp: Skip frequency resetting of si570 clocks during probe
+    - net: macb: In ZynqMP resume always configure PS GTR for non-wakeup source
+    - spi: spi-zynqmp-gqspi: Fix call trace during QSPI suspend
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Wed, 30 Nov 2022 09:04:53 +1000
+
+linux-xilinx-zynqmp (5.15.0-1015.16) jammy; urgency=medium
+
+  * Enable new version of XRT kernel driver
+    - Update XRT 2022.1 kernel modules
+
+  * Failed to edit jammy kernel configuration with custom build flow
+    - [Config] upgrade debug symbols from DWARF4 to DWARF5
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update annotation to remove unnecessary settings
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 29 Sep 2022 09:58:53 +1000
+
+linux-xilinx-zynqmp (5.15.0-1014.15) jammy; urgency=medium
+
+  * Miscellaneous upstream changes
+    - clk: versalclock7: Use index to output mapping to reference banks
+    - dt-bindings: usb: dwc3: Add snps,xhci-reset-on-resume quirk
+    - usb: add quirk for xhci reinit warning on resume
+    - arm: dts: zynqmp: add snps,xhci-reset-on-resume quirk
+    - clk: versaclock7: Use a property to differentiate between nodes
+    - net: macb: In shared MDIO usecase make MDIO producer ethernet node to probe
+      first
+    - net: macb: Fix macb mdiobus handing for DT nodes without phy-handle
+    - net: macb: Fix ZynqMP SGMII non-wakeup source resume failure
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Tue, 30 Aug 2022 07:56:52 +0200
+
+linux-xilinx-zynqmp (5.15.0-1013.14) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1983604)
+    - Enable xilinx-isp-module kernel module
+
+  * INVALID or PRIVATE BUG (LP: #1983577)
+    - [Config] Enable CONFIG_VIDEO_XILINX_AXI4S_SUBSETCONV
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 11 Aug 2022 10:02:38 +1000
+
+linux-xilinx-zynqmp (5.15.0-1012.13) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enable do_enforce_all and update annotations
+    - [Config] Update configs
+
+  * Miscellaneous upstream changes
+    - arm64: zynqmp: Enable DP for kv260-revA board
+    - arm64: zynqmp: Fix usb node drive strength and slew rate
+    - dt-bindings: Renesas versaclock7 device tree bindings
+    - clk: versalclock7: Add Renesas versaclock7 ccf device driver
+    - xilinx: Enable renesas,versaclock7 driver
+    - drm: xlnx: mixer: Correct the fourcc string copy
+
+  [ Ubuntu: 5.15.0-43.46 ]
+
+  * jammy/linux: 5.15.0-43.46 -proposed tracker (LP: #1981243)
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2022.07.11)
+  * nbd: requests can become stuck when disconnecting from server with qemu-nbd
+    (LP: #1896350)
+    - nbd: don't handle response without a corresponding request message
+    - nbd: make sure request completion won't concurrent
+    - nbd: don't clear 'NBD_CMD_INFLIGHT' flag if request is not completed
+    - nbd: fix io hung while disconnecting device
+  * Ubuntu 22.04 and 20.04 DPC Fixes for Failure Cases of DownPort Containment
+    events (LP: #1965241)
+    - PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
+    - PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
+    - [Config] Enable config option CONFIG_PCIE_EDR
+  * [SRU] Ubuntu 22.04 Feature Request-Add support for a NVMe-oF-TCP CDC Client
+    - TP 8010 (LP: #1948626)
+    - nvme: add CNTRLTYPE definitions for 'identify controller'
+    - nvme: send uevent on connection up
+    - nvme: expose cntrltype and dctype through sysfs
+  * [UBUNTU 22.04] Kernel oops while removing device from cio_ignore list
+    (LP: #1980951)
+    - s390/cio: derive cdev information only for IO-subchannels
+  * Jammy Charmed OpenStack deployment fails over connectivity issues when using
+    converged OVS bridge for control and data planes (LP: #1978820)
+    - net/mlx5e: TC NIC mode, fix tc chains miss table
+  * Hairpin traffic does not work with centralized NAT gw (LP: #1967856)
+    - net: openvswitch: fix misuse of the cached connection on tuple changes
+  * alsa: asoc: amd: the internal mic can't be dedected on yellow carp machines
+    (LP: #1980700)
+    - ASoC: amd: Add driver data to acp6x machine driver
+    - ASoC: amd: Add support for enabling DMIC on acp6x via _DSD
+  * AMD ACP 6.x DMIC Supports (LP: #1949245)
+    - ASoC: amd: add Yellow Carp ACP6x IP register header
+    - ASoC: amd: add Yellow Carp ACP PCI driver
+    - ASoC: amd: add acp6x init/de-init functions
+    - ASoC: amd: add platform devices for acp6x pdm driver and dmic driver
+    - ASoC: amd: add acp6x pdm platform driver
+    - ASoC: amd: add acp6x irq handler
+    - ASoC: amd: add acp6x pdm driver dma ops
+    - ASoC: amd: add acp6x pci driver pm ops
+    - ASoC: amd: add acp6x pdm driver pm ops
+    - ASoC: amd: enable Yellow carp acp6x drivers build
+    - ASoC: amd: create platform device for acp6x machine driver
+    - ASoC: amd: add YC machine driver using dmic
+    - ASoC: amd: enable Yellow Carp platform machine driver build
+    - ASoC: amd: fix uninitialized variable in snd_acp6x_probe()
+    - [Config] Enable AMD ACP 6 DMIC Support
+  * [UBUNTU 20.04] Include patches to avoid self-detected stall with Secure
+    Execution (LP: #1979296)
+    - KVM: s390: pv: add macros for UVC CC values
+    - KVM: s390: pv: avoid stalls when making pages secure
+  * [22.04 FEAT] KVM: Attestation support for Secure Execution (crypto)
+    (LP: #1959973)
+    - drivers/s390/char: Add Ultravisor io device
+    - s390/uv_uapi: depend on CONFIG_S390
+    - [Config] CONFIG_S390_UV_UAPI=y for s390x
+  * CVE-2022-1679
+    - SAUCE: ath9k: fix use-after-free in ath9k_hif_usb_rx_cb
+  * CVE-2022-28893
+    - SUNRPC: Ensure we flush any closed sockets before xs_xprt_free()
+    - SUNRPC: Don't leak sockets in xs_local_connect()
+  * CVE-2022-34918
+    - netfilter: nf_tables: stricter validation of element data
+  * CVE-2022-1652
+    - floppy: use a statically allocated error counter
+
+  [ Ubuntu: 5.15.0-41.44 ]
+
+  * jammy/linux: 5.15.0-41.44 -proposed tracker (LP: #1979448)
+  * Fix can't boot up after change to vmd  (LP: #1976587)
+    - PCI: vmd: Assign VMD IRQ domain before enumeration
+    - PCI: vmd: Revert 2565e5b69c44 ("PCI: vmd: Do not disable MSI-X remapping if
+      interrupt remapping is enabled by IOMMU.")
+  * [SRU][Jammy/OEM-5.17][PATCH 0/1] Fix calltrace in mac80211 (LP: #1978297)
+    - mac80211: fix struct ieee80211_tx_info size
+  * [SRU][Jammy][PATCH 0/1] Fix amd display corruption on s2idle resume
+    (LP: #1978244)
+    - drm/amd/display: Don't reinitialize DMCUB on s0ix resume
+  * pl2303 serial adapter not recognized (LP: #1967493)
+    - USB: serial: pl2303: fix type detection for odd device
+  * Remove SAUCE patches from test_vxlan_under_vrf.sh in net of
+    ubuntu_kernel_selftests (LP: #1975691)
+    - Revert "UBUNTU: SAUCE: selftests: net: Don't fail test_vxlan_under_vrf on
+      xfail"
+    - Revert "UBUNTU: SAUCE: selftests: net: Make test for VXLAN underlay in non-
+      default VRF an expected failure"
+  * Fix hp_wmi_read_int() reporting error (0x05) (LP: #1979051)
+    - platform/x86: hp-wmi: Fix hp_wmi_read_int() reporting error (0x05)
+  * Request to back port vmci patches to Ubuntu kernel (LP: #1978145)
+    - VMCI: dma dg: whitespace formatting change for vmci register defines
+    - VMCI: dma dg: add MMIO access to registers
+    - VMCI: dma dg: detect DMA datagram capability
+    - VMCI: dma dg: set OS page size
+    - VMCI: dma dg: register dummy IRQ handlers for DMA datagrams
+    - VMCI: dma dg: allocate send and receive buffers for DMA datagrams
+    - VMCI: dma dg: add support for DMA datagrams sends
+    - VMCI: dma dg: add support for DMA datagrams receive
+    - VMCI: Fix some error handling paths in vmci_guest_probe_device()
+    - VMCI: Release notification_bitmap in error path
+    - VMCI: Check exclusive_vectors when freeing interrupt 1
+    - VMCI: Add support for ARM64
+    - [Config] Update policies for VMWARE_VMCI and VMWARE_VMCI_VSOCKETS
+  * [UBUNTU 20.04] rcu stalls with many storage key guests (LP: #1975582)
+    - s390/gmap: voluntarily schedule during key setting
+    - s390/mm: use non-quiescing sske for KVM switch to keyed guest
+  * [SRU][OEM-5.14/OEM-5.17/Jammy][PATCH 0/1] Fix i915 calltrace on new ADL BIOS
+    (LP: #1976214)
+    - drm/i915: update new TMDS clock setting defined by VBT
+  * Revert PPC get_user workaround (LP: #1976248)
+    - powerpc: Export mmu_feature_keys[] as non-GPL
+  * Jammy update: v5.15.39 upstream stable release (LP: #1978240)
+    - MIPS: Fix CP0 counter erratum detection for R4k CPUs
+    - parisc: Merge model and model name into one line in /proc/cpuinfo
+    - ALSA: hda/realtek: Add quirk for Yoga Duet 7 13ITL6 speakers
+    - ALSA: fireworks: fix wrong return count shorter than expected by 4 bytes
+    - mmc: sdhci-msm: Reset GCC_SDCC_BCR register for SDHC
+    - mmc: sunxi-mmc: Fix DMA descriptors allocated above 32 bits
+    - mmc: core: Set HS clock speed before sending HS CMD13
+    - gpiolib: of: fix bounds check for 'gpio-reserved-ranges'
+    - x86/fpu: Prevent FPU state corruption
+    - KVM: x86/svm: Account for family 17h event renumberings in
+      amd_pmc_perf_hw_id
+    - iommu/vt-d: Calculate mask for non-aligned flushes
+    - iommu/arm-smmu-v3: Fix size calculation in arm_smmu_mm_invalidate_range()
+    - drm/amd/display: Avoid reading audio pattern past AUDIO_CHANNELS_COUNT
+    - drm/amdgpu: do not use passthrough mode in Xen dom0
+    - RISC-V: relocate DTB if it's outside memory region
+    - Revert "SUNRPC: attempt AF_LOCAL connect on setup"
+    - timekeeping: Mark NMI safe time accessors as notrace
+    - firewire: fix potential uaf in outbound_phy_packet_callback()
+    - firewire: remove check of list iterator against head past the loop body
+    - firewire: core: extend card->lock in fw_core_handle_bus_reset
+    - net: stmmac: disable Split Header (SPH) for Intel platforms
+    - genirq: Synchronize interrupt thread startup
+    - ASoC: da7219: Fix change notifications for tone generator frequency
+    - ASoC: wm8958: Fix change notifications for DSP controls
+    - ASoC: meson: Fix event generation for AUI ACODEC mux
+    - ASoC: meson: Fix event generation for G12A tohdmi mux
+    - ASoC: meson: Fix event generation for AUI CODEC mux
+    - s390/dasd: fix data corruption for ESE devices
+    - s390/dasd: prevent double format of tracks for ESE devices
+    - s390/dasd: Fix read for ESE with blksize < 4k
+    - s390/dasd: Fix read inconsistency for ESE DASD devices
+    - can: grcan: grcan_close(): fix deadlock
+    - can: isotp: remove re-binding of bound socket
+    - can: grcan: use ofdev->dev when allocating DMA memory
+    - can: grcan: grcan_probe(): fix broken system id check for errata workaround
+      needs
+    - can: grcan: only use the NAPI poll budget for RX
+    - nfc: replace improper check device_is_registered() in netlink related
+      functions
+    - nfc: nfcmrvl: main: reorder destructive operations in
+      nfcmrvl_nci_unregister_dev to avoid bugs
+    - NFC: netlink: fix sleep in atomic bug when firmware download timeout
+    - gpio: visconti: Fix fwnode of GPIO IRQ
+    - gpio: pca953x: fix irq_stat not updated when irq is disabled (irq_mask not
+      set)
+    - hwmon: (adt7470) Fix warning on module removal
+    - hwmon: (pmbus) disable PEC if not enabled
+    - ASoC: dmaengine: Restore NULL prepare_slave_config() callback
+    - ASoC: soc-ops: fix error handling
+    - iommu/vt-d: Drop stop marker messages
+    - iommu/dart: check return value after calling platform_get_resource()
+    - net/mlx5e: Fix trust state reset in reload
+    - net/mlx5e: Don't match double-vlan packets if cvlan is not set
+    - net/mlx5e: CT: Fix queued up restore put() executing after relevant ft
+      release
+    - net/mlx5e: Fix the calling of update_buffer_lossy() API
+    - net/mlx5: Avoid double clear or set of sync reset requested
+    - net/mlx5: Fix deadlock in sync reset flow
+    - selftests/seccomp: Don't call read() on TTY from background pgrp
+    - SUNRPC release the transport of a relocated task with an assigned transport
+    - RDMA/siw: Fix a condition race issue in MPA request processing
+    - RDMA/irdma: Flush iWARP QP if modified to ERR from RTR state
+    - RDMA/irdma: Reduce iWARP QP destroy time
+    - RDMA/irdma: Fix possible crash due to NULL netdev in notifier
+    - NFSv4: Don't invalidate inode attributes on delegation return
+    - net: ethernet: mediatek: add missing of_node_put() in mtk_sgmii_init()
+    - net: dsa: mt7530: add missing of_node_put() in mt7530_setup()
+    - net: stmmac: dwmac-sun8i: add missing of_node_put() in
+      sun8i_dwmac_register_mdio_mux()
+    - net: mdio: Fix ENOMEM return value in BCM6368 mux bus controller
+    - net: cpsw: add missing of_node_put() in cpsw_probe_dt()
+    - net: igmp: respect RCU rules in ip_mc_source() and ip_mc_msfilter()
+    - net: emaclite: Add error handling for of_address_to_resource()
+    - selftests/net: so_txtime: fix parsing of start time stamp on 32 bit systems
+    - selftests/net: so_txtime: usage(): fix documentation of default clock
+    - drm/msm/dp: remove fail safe mode related code
+    - btrfs: do not BUG_ON() on failure to update inode when setting xattr
+    - hinic: fix bug of wq out of bound access
+    - mld: respect RCU rules in ip6_mc_source() and ip6_mc_msfilter()
+    - rxrpc: Enable IPv6 checksums on transport socket
+    - selftests: mirror_gre_bridge_1q: Avoid changing PVID while interface is
+      operational
+    - bnxt_en: Fix possible bnxt_open() failure caused by wrong RFS flag
+    - bnxt_en: Fix unnecessary dropping of RX packets
+    - selftests: ocelot: tc_flower_chains: specify conform-exceed action for
+      policer
+    - smsc911x: allow using IRQ0
+    - btrfs: force v2 space cache usage for subpage mount
+    - btrfs: always log symlinks in full mode
+    - gpio: mvebu: drop pwm base assignment
+    - kvm: x86/cpuid: Only provide CPUID leaf 0xA if host has architectural PMU
+    - net/mlx5: Fix slab-out-of-bounds while reading resource dump menu
+    - net/mlx5e: Lag, Fix use-after-free in fib event handler
+    - net/mlx5e: Lag, Fix fib_info pointer assignment
+    - net/mlx5e: Lag, Don't skip fib events on current dst
+    - iommu/dart: Add missing module owner to ops structure
+    - kvm: selftests: do not use bitfields larger than 32-bits for PTEs
+    - KVM: selftests: Silence compiler warning in the kvm_page_table_test
+    - x86/kvm: Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
+    - KVM: x86: Do not change ICR on write to APIC_SELF_IPI
+    - KVM: x86/mmu: avoid NULL-pointer dereference on page freeing bugs
+    - KVM: LAPIC: Enable timer posted-interrupt only when mwait/hlt is advertised
+    - selftest/vm: verify mmap addr in mremap_test
+    - selftest/vm: verify remap destination address in mremap_test
+    - Revert "parisc: Mark sched_clock unstable only if clocks are not
+      syncronized"
+    - rcu: Fix callbacks processing time limit retaining cond_resched()
+    - rcu: Apply callbacks processing time limit only on softirq
+    - PCI: pci-bridge-emul: Add description for class_revision field
+    - PCI: pci-bridge-emul: Add definitions for missing capabilities registers
+    - PCI: aardvark: Add support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
+      registers on emulated bridge
+    - PCI: aardvark: Clear all MSIs at setup
+    - PCI: aardvark: Comment actions in driver remove method
+    - PCI: aardvark: Disable bus mastering when unbinding driver
+    - PCI: aardvark: Mask all interrupts when unbinding driver
+    - PCI: aardvark: Fix memory leak in driver unbind
+    - PCI: aardvark: Assert PERST# when unbinding driver
+    - PCI: aardvark: Disable link training when unbinding driver
+    - PCI: aardvark: Disable common PHY when unbinding driver
+    - PCI: aardvark: Replace custom PCIE_CORE_INT_* macros with PCI_INTERRUPT_*
+    - PCI: aardvark: Check return value of generic_handle_domain_irq() when
+      processing INTx IRQ
+    - PCI: aardvark: Make MSI irq_chip structures static driver structures
+    - PCI: aardvark: Make msi_domain_info structure a static driver structure
+    - PCI: aardvark: Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node)
+    - PCI: aardvark: Refactor unmasking summary MSI interrupt
+    - PCI: aardvark: Add support for masking MSI interrupts
+    - PCI: aardvark: Fix setting MSI address
+    - PCI: aardvark: Enable MSI-X support
+    - PCI: aardvark: Add support for ERR interrupt on emulated bridge
+    - PCI: aardvark: Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on
+      emulated bridge
+    - PCI: aardvark: Add support for PME interrupts
+    - PCI: aardvark: Fix support for PME requester on emulated bridge
+    - PCI: aardvark: Use separate INTA interrupt for emulated root bridge
+    - PCI: aardvark: Remove irq_mask_ack() callback for INTx interrupts
+    - PCI: aardvark: Don't mask irq when mapping
+    - PCI: aardvark: Drop __maybe_unused from advk_pcie_disable_phy()
+    - PCI: aardvark: Update comment about link going down after link-up
+    - Linux 5.15.39
+  * Jammy update: v5.15.38 upstream stable release (LP: #1978234)
+    - usb: mtu3: fix USB 3.0 dual-role-switch from device to host
+    - USB: quirks: add a Realtek card reader
+    - USB: quirks: add STRING quirk for VCOM device
+    - USB: serial: whiteheat: fix heap overflow in WHITEHEAT_GET_DTR_RTS
+    - USB: serial: cp210x: add PIDs for Kamstrup USB Meter Reader
+    - USB: serial: option: add support for Cinterion MV32-WA/MV32-WB
+    - USB: serial: option: add Telit 0x1057, 0x1058, 0x1075 compositions
+    - usb: xhci: tegra:Fix PM usage reference leak of
+      tegra_xusb_unpowergate_partitions
+    - xhci: Enable runtime PM on second Alderlake controller
+    - xhci: stop polling roothubs after shutdown
+    - xhci: increase usb U3 -> U0 link resume timeout from 100ms to 500ms
+    - iio: dac: ad5592r: Fix the missing return value.
+    - iio: dac: ad5446: Fix read_raw not returning set value
+    - iio: magnetometer: ak8975: Fix the error handling in ak8975_power_on()
+    - iio: imu: inv_icm42600: Fix I2C init possible nack
+    - usb: misc: fix improper handling of refcount in uss720_probe()
+    - usb: core: Don't hold the device lock while sleeping in do_proc_control()
+    - usb: typec: ucsi: Fix reuse of completion structure
+    - usb: typec: ucsi: Fix role swapping
+    - usb: gadget: uvc: Fix crash when encoding data for usb request
+    - usb: gadget: configfs: clear deactivation flag in
+      configfs_composite_unbind()
+    - usb: dwc3: Try usb-role-switch first in dwc3_drd_init
+    - usb: dwc3: core: Fix tx/rx threshold settings
+    - usb: dwc3: core: Only handle soft-reset in DCTL
+    - usb: dwc3: gadget: Return proper request status
+    - usb: dwc3: pci: add support for the Intel Meteor Lake-P
+    - usb: cdns3: Fix issue for clear halt endpoint
+    - usb: phy: generic: Get the vbus supply
+    - serial: imx: fix overrun interrupts in DMA mode
+    - serial: amba-pl011: do not time out prematurely when draining tx fifo
+    - serial: 8250: Also set sticky MCR bits in console restoration
+    - serial: 8250: Correct the clock for EndRun PTP/1588 PCIe device
+    - arch_topology: Do not set llc_sibling if llc_id is invalid
+    - ceph: fix possible NULL pointer dereference for req->r_session
+    - bus: mhi: host: pci_generic: Add missing poweroff() PM callback
+    - bus: mhi: host: pci_generic: Flush recovery worker during freeze
+    - arm64: dts: imx8mm-venice: fix spi2 pin configuration
+    - pinctrl: samsung: fix missing GPIOLIB on ARM64 Exynos config
+    - hex2bin: make the function hex_to_bin constant-time
+    - hex2bin: fix access beyond string end
+    - riscv: patch_text: Fixup last cpu should be master
+    - x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
+    - iocost: don't reset the inuse weight of under-weighted debtors
+    - virtio_net: fix wrong buf address calculation when using xdp
+    - cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
+    - cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
+    - video: fbdev: udlfb: properly check endpoint type
+    - arm64: dts: meson: remove CPU opps below 1GHz for G12B boards
+    - arm64: dts: meson: remove CPU opps below 1GHz for SM1 boards
+    - iio:imu:bmi160: disable regulator in error path
+    - mtd: rawnand: fix ecc parameters for mt7622
+    - xsk: Fix l2fwd for copy mode + busy poll combo
+    - arm64: dts: imx8qm: Correct SCU clock controller's compatible property
+    - USB: Fix xhci event ring dequeue pointer ERDP update issue
+    - ARM: dts: imx6qdl-apalis: Fix sgtl5000 detection issue
+    - arm64: dts: imx8mn: Fix SAI nodes
+    - arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO pin labeling for CON1
+    - phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe
+    - phy: samsung: exynos5250-sata: fix missing device put in probe error paths
+    - ARM: OMAP2+: Fix refcount leak in omap_gic_of_init
+    - bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific
+    - ARM: dts: dra7: Fix suspend warning for vpe powerdomain
+    - phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks
+    - ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
+    - ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
+    - ARM: dts: at91: fix pinctrl phandles
+    - phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe
+    - phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe
+    - interconnect: qcom: sdx55: Drop IP0 interconnects
+    - ARM: dts: Fix mmc order for omap3-gta04
+    - ARM: dts: am3517-evm: Fix misc pinmuxing
+    - ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
+    - ipvs: correctly print the memory size of ip_vs_conn_tab
+    - phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe()
+    - pinctrl: mediatek: moore: Fix build error
+    - mtd: rawnand: Fix return value check of wait_for_completion_timeout
+    - mtd: fix 'part' field data corruption in mtd_info
+    - pinctrl: stm32: Do not call stm32_gpio_get() for edge triggered IRQs in EOI
+    - memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
+    - net: dsa: Add missing of_node_put() in dsa_port_link_register_of
+    - netfilter: nft_set_rbtree: overlap detection with element re-addition after
+      deletion
+    - bpf, lwt: Fix crash when using bpf_skb_set_tunnel_key() from bpf_xmit lwt
+      hook
+    - pinctrl: rockchip: fix RK3308 pinmux bits
+    - tcp: md5: incorrect tcp_header_len for incoming connections
+    - pinctrl: stm32: Keep pinctrl block clock enabled when LEVEL IRQ requested
+    - tcp: ensure to use the most recently sent skb when filling the rate sample
+    - wireguard: device: check for metadata_dst with skb_valid_dst()
+    - sctp: check asoc strreset_chunk in sctp_generate_reconf_event
+    - ARM: dts: imx6ull-colibri: fix vqmmc regulator
+    - arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
+    - pinctrl: pistachio: fix use of irq_of_parse_and_map()
+    - cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
+    - net: hns3: clear inited state and stop client after failed to register
+      netdev
+    - net: hns3: modify the return code of hclge_get_ring_chain_from_mbx
+    - net: hns3: add validity check for message data length
+    - net: hns3: add return value for mailbox handling in PF
+    - net/smc: sync err code when tcp connection was refused
+    - ip_gre: Make o_seqno start from 0 in native mode
+    - ip6_gre: Make o_seqno start from 0 in native mode
+    - ip_gre, ip6_gre: Fix race condition on o_seqno in collect_md mode
+    - tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT
+    - tcp: make sure treq->af_specific is initialized
+    - bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
+    - clk: sunxi: sun9i-mmc: check return value after calling
+      platform_get_resource()
+    - cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
+    - net: bcmgenet: hide status block before TX timestamping
+    - net: phy: marvell10g: fix return value on error
+    - net: dsa: mv88e6xxx: Fix port_hidden_wait to account for port_base_addr
+    - drm/sun4i: Remove obsolete references to PHYS_OFFSET
+    - net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK
+    - io_uring: check reserved fields for send/sendmsg
+    - io_uring: check reserved fields for recv/recvmsg
+    - netfilter: conntrack: fix udp offload timeout sysctl
+    - drm/amdkfd: Fix GWS queue count
+    - drm/amd/display: Fix memory leak in dcn21_clock_source_create
+    - tls: Skip tls_append_frag on zero copy size
+    - bnx2x: fix napi API usage sequence
+    - net: fec: add missing of_node_put() in fec_enet_init_stop_mode()
+    - gfs2: Prevent endless loops in gfs2_file_buffered_write
+    - gfs2: Minor retry logic cleanup
+    - gfs2: Make sure not to return short direct writes
+    - gfs2: No short reads or writes upon glock contention
+    - perf arm-spe: Fix addresses of synthesized SPE events
+    - ixgbe: ensure IPsec VF<->PF compatibility
+    - Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"
+    - tcp: fix F-RTO may not work correctly when receiving DSACK
+    - ASoC: Intel: soc-acpi: correct device endpoints for max98373
+    - ASoC: wm8731: Disable the regulator when probing fails
+    - ext4: fix bug_on in start_this_handle during umount filesystem
+    - arch: xtensa: platforms: Fix deadlock in rs_close()
+    - ksmbd: increment reference count of parent fp
+    - ksmbd: set fixed sector size to FS_SECTOR_SIZE_INFORMATION
+    - bonding: do not discard lowest hash bit for non layer3+4 hashing
+    - x86: __memcpy_flushcache: fix wrong alignment if size > 2^32
+    - cifs: destage any unwritten data to the server before calling
+      copychunk_write
+    - drivers: net: hippi: Fix deadlock in rr_close()
+    - powerpc/perf: Fix 32bit compile
+    - selftest/vm: verify mmap addr in mremap_test
+    - selftest/vm: verify remap destination address in mremap_test
+    - Revert "ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40"
+    - zonefs: Fix management of open zones
+    - zonefs: Clear inode information flags on inode creation
+    - kasan: prevent cpu_quarantine corruption when CPU offline and cache shrink
+      occur at same time
+    - mtd: rawnand: qcom: fix memory corruption that causes panic
+    - netfilter: Update ip6_route_me_harder to consider L3 domain
+    - drm/i915: Check EDID for HDR static metadata when choosing blc
+    - drm/i915: Fix SEL_FETCH_PLANE_*(PIPE_B+) register addresses
+    - net: ethernet: stmmac: fix write to sgmii_adapter_base
+    - ACPI: processor: idle: Avoid falling back to C3 type C-states
+    - thermal: int340x: Fix attr.show callback prototype
+    - btrfs: fix leaked plug after failure syncing log on zoned filesystems
+    - ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
+    - ARM: dts: imx8mm-venice-gw{71xx,72xx,73xx}: fix OTG controller OC mode
+    - x86/cpu: Load microcode during restore_processor_state()
+    - perf symbol: Pass is_kallsyms to symbols__fixup_end()
+    - perf symbol: Update symbols__fixup_end()
+    - tty: n_gsm: fix restart handling via CLD command
+    - tty: n_gsm: fix decoupled mux resource
+    - tty: n_gsm: fix mux cleanup after unregister tty device
+    - tty: n_gsm: fix wrong signal octet encoding in convergence layer type 2
+    - tty: n_gsm: fix malformed counter for out of frame data
+    - netfilter: nft_socket: only do sk lookups when indev is available
+    - tty: n_gsm: fix insufficient txframe size
+    - tty: n_gsm: fix wrong DLCI release order
+    - tty: n_gsm: fix missing explicit ldisc flush
+    - tty: n_gsm: fix wrong command retry handling
+    - tty: n_gsm: fix wrong command frame length field encoding
+    - tty: n_gsm: fix wrong signal octets encoding in MSC
+    - tty: n_gsm: fix missing tty wakeup in convergence layer type 2
+    - tty: n_gsm: fix reset fifo race condition
+    - tty: n_gsm: fix incorrect UA handling
+    - tty: n_gsm: fix software flow control handling
+    - perf symbol: Remove arch__symbols__fixup_end()
+    - eeprom: at25: Use DMA safe buffers
+    - objtool: Fix code relocs vs weak symbols
+    - objtool: Fix type of reloc::addend
+    - powerpc/64: Add UADDR64 relocation support
+    - Linux 5.15.38
+  * Jammy update: v5.15.37 upstream stable release (LP: #1976135)
+    - floppy: disable FDRAWCMD by default
+    - [Config] updateconfigs for BLK_DEV_FD_RAWCMD
+    - bpf: Introduce composable reg, ret and arg types.
+    - bpf: Replace ARG_XXX_OR_NULL with ARG_XXX | PTR_MAYBE_NULL
+    - bpf: Replace RET_XXX_OR_NULL with RET_XXX | PTR_MAYBE_NULL
+    - bpf: Replace PTR_TO_XXX_OR_NULL with PTR_TO_XXX | PTR_MAYBE_NULL
+    - bpf: Introduce MEM_RDONLY flag
+    - bpf: Convert PTR_TO_MEM_OR_NULL to composable types.
+    - bpf: Make per_cpu_ptr return rdonly PTR_TO_MEM.
+    - bpf: Add MEM_RDONLY for helper args that are pointers to rdonly mem.
+    - bpf/selftests: Test PTR_TO_RDONLY_MEM
+    - bpf: Fix crash due to out of bounds access into reg2btf_ids.
+    - spi: cadence-quadspi: fix write completion support
+    - ARM: dts: socfpga: change qspi to "intel,socfpga-qspi"
+    - mm: kfence: fix objcgs vector allocation
+    - gup: Turn fault_in_pages_{readable,writeable} into
+      fault_in_{readable,writeable}
+    - iov_iter: Turn iov_iter_fault_in_readable into fault_in_iov_iter_readable
+    - iov_iter: Introduce fault_in_iov_iter_writeable
+    - gfs2: Add wrapper for iomap_file_buffered_write
+    - gfs2: Clean up function may_grant
+    - gfs2: Introduce flag for glock holder auto-demotion
+    - gfs2: Move the inode glock locking to gfs2_file_buffered_write
+    - gfs2: Eliminate ip->i_gh
+    - gfs2: Fix mmap + page fault deadlocks for buffered I/O
+    - iomap: Fix iomap_dio_rw return value for user copies
+    - iomap: Support partial direct I/O on user copy failures
+    - iomap: Add done_before argument to iomap_dio_rw
+    - gup: Introduce FOLL_NOFAULT flag to disable page faults
+    - iov_iter: Introduce nofault flag to disable page faults
+    - gfs2: Fix mmap + page fault deadlocks for direct I/O
+    - btrfs: fix deadlock due to page faults during direct IO reads and writes
+    - btrfs: fallback to blocking mode when doing async dio over multiple extents
+    - mm: gup: make fault_in_safe_writeable() use fixup_user_fault()
+    - selftests/bpf: Add test for reg2btf_ids out of bounds access
+    - Linux 5.15.37
+  * CVE-2022-1789
+    - KVM: x86/mmu: fix NULL pointer dereference on guest INVPCID
+  * Jammy update: v5.15.36 upstream stable release (LP: #1972905)
+    - block: simplify the block device syncing code
+    - xfs: return errors in xfs_fs_sync_fs
+    - dma-mapping: remove bogus test for pfn_valid from dma_map_resource
+    - arm64/mm: drop HAVE_ARCH_PFN_VALID
+    - etherdevice: Adjust ether_addr* prototypes to silence -Wstringop-overead
+    - mm: page_alloc: fix building error on -Werror=array-compare
+    - perf tools: Fix segfault accessing sample_id xyarray
+    - mm, kfence: support kmem_dump_obj() for KFENCE objects
+    - gfs2: assign rgrp glock before compute_bitstructs
+    - scsi: ufs: core: scsi_get_lba() error fix
+    - ALSA: usb-audio: Clear MIDI port active flag after draining
+    - ALSA: hda/realtek: Add quirk for Clevo NP70PNP
+    - ASoC: atmel: Remove system clock tree configuration for at91sam9g20ek
+    - ASoC: topology: Correct error handling in soc_tplg_dapm_widget_create()
+    - ASoC: rk817: Use devm_clk_get() in rk817_platform_probe
+    - ASoC: msm8916-wcd-digital: Check failure for devm_snd_soc_register_component
+    - ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use
+    - dmaengine: idxd: fix device cleanup on disable
+    - dmaengine: imx-sdma: Fix error checking in sdma_event_remap
+    - dmaengine: mediatek:Fix PM usage reference leak of
+      mtk_uart_apdma_alloc_chan_resources
+    - dmaengine: dw-edma: Fix unaligned 64bit access
+    - spi: spi-mtk-nor: initialize spi controller after resume
+    - esp: limit skb_page_frag_refill use to a single page
+    - spi: cadence-quadspi: fix incorrect supports_op() return value
+    - igc: Fix infinite loop in release_swfw_sync
+    - igc: Fix BUG: scheduling while atomic
+    - igc: Fix suspending when PTM is active
+    - ALSA: hda/hdmi: fix warning about PCM count when used with SOF
+    - rxrpc: Restore removed timer deletion
+    - net/smc: Fix sock leak when release after smc_shutdown()
+    - net/packet: fix packet_sock xmit return value checking
+    - ip6_gre: Avoid updating tunnel->tun_hlen in __gre6_xmit()
+    - ip6_gre: Fix skb_under_panic in __gre6_xmit()
+    - net: restore alpha order to Ethernet devices in config
+    - net/sched: cls_u32: fix possible leak in u32_init_knode()
+    - l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using
+      netdev_master_upper_dev_get_rcu
+    - ipv6: make ip6_rt_gc_expire an atomic_t
+    - can: isotp: stop timeout monitoring when no first frame was sent
+    - net: dsa: hellcreek: Calculate checksums in tagger
+    - net: mscc: ocelot: fix broken IP multicast flooding
+    - netlink: reset network and mac headers in netlink_dump()
+    - drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in
+      intel_psr2_config_valid() fails
+    - net: stmmac: Use readl_poll_timeout_atomic() in atomic state
+    - dmaengine: idxd: add RO check for wq max_batch_size write
+    - dmaengine: idxd: add RO check for wq max_transfer_size write
+    - dmaengine: idxd: skip clearing device context when device is read-only
+    - selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
+    - arm64: mm: fix p?d_leaf()
+    - ARM: vexpress/spc: Avoid negative array index when !SMP
+    - reset: renesas: Check return value of reset_control_deassert()
+    - reset: tegra-bpmp: Restore Handle errors in BPMP response
+    - platform/x86: samsung-laptop: Fix an unsigned comparison which can never be
+      negative
+    - ALSA: usb-audio: Fix undefined behavior due to shift overflowing the
+      constant
+    - drm/msm/disp: check the return value of kzalloc()
+    - arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
+    - vxlan: fix error return code in vxlan_fdb_append
+    - cifs: Check the IOCB_DIRECT flag, not O_DIRECT
+    - mt76: Fix undefined behavior due to shift overflowing the constant
+    - brcmfmac: sdio: Fix undefined behavior due to shift overflowing the constant
+    - dpaa_eth: Fix missing of_node_put in dpaa_get_ts_info()
+    - drm/msm/mdp5: check the return of kzalloc()
+    - net: macb: Restart tx only if queue pointer is lagging
+    - scsi: iscsi: Release endpoint ID when its freed
+    - scsi: iscsi: Merge suspend fields
+    - scsi: iscsi: Fix NOP handling during conn recovery
+    - scsi: qedi: Fix failed disconnect handling
+    - stat: fix inconsistency between struct stat and struct compat_stat
+    - VFS: filename_create(): fix incorrect intent.
+    - nvme: add a quirk to disable namespace identifiers
+    - nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
+    - nvme-pci: disable namespace identifiers for Qemu controllers
+    - EDAC/synopsys: Read the error count from the correct register
+    - mm/memory-failure.c: skip huge_zero_page in memory_failure()
+    - memcg: sync flush only if periodic flush is delayed
+    - mm, hugetlb: allow for "high" userspace addresses
+    - oom_kill.c: futex: delay the OOM reaper to allow time for proper futex
+      cleanup
+    - mm/mmu_notifier.c: fix race in mmu_interval_notifier_remove()
+    - ata: pata_marvell: Check the 'bmdma_addr' beforing reading
+    - dma: at_xdmac: fix a missing check on list iterator
+    - dmaengine: imx-sdma: fix init of uart scripts
+    - net: atlantic: invert deep par in pm functions, preventing null derefs
+    - Input: omap4-keypad - fix pm_runtime_get_sync() error checking
+    - scsi: sr: Do not leak information in ioctl
+    - sched/pelt: Fix attach_entity_load_avg() corner case
+    - perf/core: Fix perf_mmap fail when CONFIG_PERF_USE_VMALLOC enabled
+    - drm/panel/raspberrypi-touchscreen: Avoid NULL deref if not initialised
+    - drm/panel/raspberrypi-touchscreen: Initialise the bridge in prepare
+    - KVM: PPC: Fix TCE handling for VFIO
+    - drm/vc4: Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
+    - powerpc/perf: Fix power9 event alternatives
+    - powerpc/perf: Fix power10 event alternatives
+    - perf script: Always allow field 'data_src' for auxtrace
+    - perf report: Set PERF_SAMPLE_DATA_SRC bit for Arm SPE event
+    - xtensa: patch_text: Fixup last cpu should be master
+    - xtensa: fix a7 clobbering in coprocessor context load/store
+    - openvswitch: fix OOB access in reserve_sfa_size()
+    - ASoC: soc-dapm: fix two incorrect uses of list iterator
+    - e1000e: Fix possible overflow in LTR decoding
+    - ARC: entry: fix syscall_trace_exit argument
+    - arm_pmu: Validate single/group leader events
+    - KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
+    - KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
+    - KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
+    - KVM: SVM: Flush when freeing encrypted pages even on SME_COHERENT CPUs
+    - netfilter: conntrack: convert to refcount_t api
+    - netfilter: conntrack: avoid useless indirection during conntrack destruction
+    - ext4: fix fallocate to use file_modified to update permissions consistently
+    - ext4: fix symlink file size not match to file content
+    - ext4: fix use-after-free in ext4_search_dir
+    - ext4, doc: fix incorrect h_reserved size
+    - ext4: fix overhead calculation to account for the reserved gdt blocks
+    - ext4: force overhead calculation if the s_overhead_cluster makes no sense
+    - netfilter: nft_ct: fix use after free when attaching zone template
+    - jbd2: fix a potential race while discarding reserved buffers after an abort
+    - spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and
+      controller
+    - block/compat_ioctl: fix range check in BLKGETSIZE
+    - arm64: dts: qcom: add IPA qcom,qmp property
+    - Linux 5.15.36
+  * Aquantia GbE LAN driver causes UBSAN error during kernel boot
+    (LP: #1958770) // Jammy update: v5.15.36 upstream stable release
+    (LP: #1972905)
+    - net: atlantic: Avoid out-of-bounds indexing
+
+  [ Ubuntu: 5.15.0-40.43 ]
+
+  * jammy/linux: 5.15.0-40.43 -proposed tracker (LP: #1978610)
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/2022.05.30)
+  * [SRU][OEM-5.14/OEM-5.17/J][PATCH 0/2] Fix system hangs after s2idle on AMD
+    A+A GPU (LP: #1975804)
+    - Revert "drm/amd/pm: keep the BACO feature enabled for suspend"
+    - drm/amd: Don't reset dGPUs if the system is going to s2idle
+  * [SRU][OEM-5.14/OEM-5.17/J][PATCH 0/1] Read the discovery registers for
+    AMD_SFH (LP: #1975798)
+    - HID: amd_sfh: Add support for sensor discovery
+  * [UBUNTU 20.04] CPU-MF: add extended counter set definitions for new IBM z16
+    (LP: #1974433)
+    - s390/cpumf: add new extended counter set for IBM z16
+  * [UBUNTU 20.04] KVM nesting support leaks too much memory, might result in
+    stalls during cleanup (LP: #1974017)
+    - KVM: s390: vsie/gmap: reduce gmap_rmap overhead
+  * [UBUNTU 20.04] Null Pointer issue in nfs code running Ubuntu on IBM Z
+    (LP: #1968096)
+    - NFS: Fix up nfs_ctx_key_to_expire()
+  * Fix REG_WAIT timeout for Yellow Carp (LP: #1971417)
+    - drm/amd/display: Clear encoder assignments when state cleared.
+    - drm/amd/display: fix stale info in link encoder assignment
+    - drm/amd/display: Query all entries in assignment table during updates.
+    - drm/amd/display: Initialise encoder assignment when initialising dc_state
+  * Enable hotspot feature for Realtek 8821CE (LP: #1969326)
+    - rtw88: Add update beacon flow for AP mode
+    - rtw88: 8821c: Enable TX report for management frames
+    - rtw88: do PHY calibration while starting AP
+    - rtw88: 8821c: fix debugfs rssi value
+    - rtw88: add ieee80211:sta_rc_update ops
+  * prevent kernel panic with overlayfs + shiftfs (LP: #1973620)
+    - SAUCE: overlayfs: prevent dereferencing struct file in ovl_vm_prfile_set()
+  * disable Intel DMA remapping by default (LP: #1971699)
+    - Revert "UBUNTU: [Config] enable Intel DMA remapping options by default"
+  * Mute/mic LEDs no function on Elitebook 630 (LP: #1974111)
+    - ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machine
+  * [Regression] Real-time Kernel Build Failure (LP: #1972899)
+    - x86/mm: Include spinlock_t definition in pgtable.
+  * build backport-iwlwifi-dkms as linux-modules-iwlwifi-ABI (LP: #1969434)
+    - [Packaging] support standalone dkms module builds
+    - [Packaging] drop do_<mod> arch specific configs
+  * IPU6 camera has no function on Andrews MLK (LP: #1964983)
+    - SAUCE: IPU6: 2022-03-11 alpha release for Andrews MLK
+    - [Config] IPU6: enable OV02C10 sensor
+    - SAUCE: IPU6: 2022-04-01 Andrews MLK PV release
+    - SAUCE: spi: ljca: return when a sub-transaction first failed
+    - SACUE: ljca: disable parallelly stub write
+    - SAUCE: ljca: fix race condition issue in runtime PM
+    - SAUCE: i2c-ljca: fix a null pointer access issue on tgl
+    - SAUCE: ljca: fix a typo issue
+    - SAUCE: ljca: assume stub enum failed as a warning
+    - SAUCE: mei: cleanup header file including
+    - SAUCE: intel_ulpss: Replaced by LJCA and remove
+    - [Config] drop intel_ulpss in favor of by LJCA
+  * multiple UBSAN warnings in Intel IPU6 camera driver at boot (LP: #1958006)
+    - SAUCE: media: pci: intel: Avoid UBSAN warnings of index bound and shift
+  * Support Intel IPU6 MIPI camera on Alder Lake platforms (LP: #1955383)
+    - SAUCE: intel ipu drivers first release
+    - SAUCE: IPU driver release WW48
+    - SAUCE: IPU driver release WW48 with MCU
+    - SAUCE: IPU driver release WW52
+    - SAUCE: IPU driver release WW04
+    - SAUCE: IPU driver release WW14
+    - SAUCE: Fix ov01a1s output mirror issue
+    - SAUCE: integrate IPU6 builds
+    - [Config] updateconfigs for IPU6 driver
+    - SAUCE: Fix ov01a1s IQ issues
+    - SAUCE: intel/ipu6: Remove unnecessary video devices
+    - SAUCE: change power control driver to acpi driver
+    - SAUCE: IPU6 driver release for kernel 5.13
+    - SAUCE: sensor HM11b1 brightness bugfix
+    - SAUCE: Fix build error on Kernel 5.13
+    - SAUCE: IPU6 driver release for kernel 5.14 on 2021-11-01
+    - [Config] IPU6: enable OV01A10 sensor
+    - SAUCE: Fix build error for kernel 5.15
+    - SAUCE: intel visual sensing controller(VSC) driver first release
+    - [Config] ivsc: enable Intel VSC drivers
+    - SAUCE: ivsc: return error when device not ready
+    - SAUCE: ivsc: add soft dependencies for intel_vsc module
+    - SAUCE: ljca: switch wait event to uninterruptible
+    - SAUCE: mei-vsc: switch wait event to uninterruptible
+    - SAUCE: mei_vsc: add ACPI HID for ADL
+    - SAUCE: ljca: add multi ACPI HID support
+    - SAUCE: ivsc: add delay for acquire camera to wait firmware ready
+    - SAUCE: mei_vsc: distinguish platform with different camera sensor
+    - SAUCE: i2c-ljca: fix a potential issue
+    - SAUCE: ljca: disable autosuspend by default
+    - [Config] make Intel IPU6 modules amd64 only
+    - SAUCE: IPU6: drop unnecessary cflags manipulation
+
+  [ Ubuntu: 5.15.0-39.42 ]
+
+  * CVE-2022-21123 // CVE-2022-21125 // CVE-2022-21166
+    - Documentation: Add documentation for Processor MMIO Stale Data
+    - x86/speculation/mmio: Enumerate Processor MMIO Stale Data bug
+    - x86/speculation: Add a common function for MD_CLEAR mitigation update
+    - x86/speculation/mmio: Add mitigation for Processor MMIO Stale Data
+    - x86/bugs: Group MDS, TAA & Processor MMIO Stale Data mitigations
+    - x86/speculation/mmio: Enable CPU Fill buffer clearing on idle
+    - x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data
+    - x86/speculation/srbds: Update SRBDS mitigation selection
+    - x86/speculation/mmio: Reuse SRBDS mitigation for SBDS
+    - KVM: x86/speculation: Disable Fill buffer clear within guests
+    - x86/speculation/mmio: Print SMT warning
+
+  [ Ubuntu: 5.15.0-37.39 ]
+
+  * netfilter newset OOB write (LP: #1976363)
+    - netfilter: nf_tables: sanitize nft_set_desc_concat_parse()
+  * CVE-2022-1966
+    - netfilter: nf_tables: disallow non-stateful expression in sets earlier
+
+  [ Ubuntu: 5.15.0-35.36 ]
+
+  * CVE-2022-21499
+    - SAUCE: debug: Lock down kgdb
+
+  [ Ubuntu: 5.15.0-34.35 ]
+
+  * jammy/linux: 5.15.0-34.35 -proposed tracker (LP: #1974322)
+  * AMD APU s2idle is broken after the ASIC reset fix (LP: #1972134)
+    - drm/amdgpu: unify BO evicting method in amdgpu_ttm
+    - drm/amdgpu: explicitly check for s0ix when evicting resources
+  * amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517
+    (LP: #1971597)
+    - gpio: Request interrupts after IRQ is initialized
+  * config CONFIG_HISI_PMU for  kunpeng920 (LP: #1956086)
+    - [Config] CONFIG_HISI_PMU=m
+  * Mute/mic LEDs no function on EliteBook G9 platfroms (LP: #1970552)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs support for HP Laptops
+  * network-manager/1.36.4-2ubuntu1 ADT test failure with linux/5.15.0-28.29
+    (LP: #1971418)
+    - Revert "rfkill: make new event layout opt-in"
+  * PCIE LnkCtl ASPM not enabled under VMD mode for Alder Lake platforms
+    (LP: #1942160)
+    - SAUCE: vmd: fixup bridge ASPM by driver name instead
+  * Mute/mic LEDs no function on HP EliteBook 845/865 G9 (LP: #1970178)
+    - ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook
+      845/865 G9
+  * Enable headset mic on Lenovo P360 (LP: #1967069)
+    - ALSA: hda/realtek: Enable headset mic on Lenovo P360
+  * WCN6856 BT keep in OFF state after coldboot system (LP: #1967067)
+    - Bluetooth: btusb: Improve stability for QCA devices
+  * Screen sometimes can't update [Failed to post KMS update: CRTC property
+    (GAMMA_LUT) not found] (LP: #1967274)
+    - drm/i915/xelpd: Enable Pipe color support for D13 platform
+    - drm/i915: Use unlocked register accesses for LUT loads
+    - drm/i915/xelpd: Enable Pipe Degamma
+    - drm/i915/xelpd: Add Pipe Color Lut caps to platform config
+  * Jammy update: v5.15.35 upstream stable release (LP: #1969857)
+    - drm/amd/display: Add pstate verification and recovery for DCN31
+    - drm/amd/display: Fix p-state allow debug index on dcn31
+    - hamradio: defer 6pack kfree after unregister_netdev
+    - hamradio: remove needs_free_netdev to avoid UAF
+    - cpuidle: PSCI: Move the `has_lpi` check to the beginning of the function
+    - ACPI: processor idle: Check for architectural support for LPI
+    - ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40
+    - btrfs: remove unused parameter nr_pages in add_ra_bio_pages()
+    - btrfs: remove no longer used counter when reading data page
+    - btrfs: remove unused variable in btrfs_{start,write}_dirty_block_groups()
+    - soc: qcom: aoss: Expose send for generic usecase
+    - dt-bindings: net: qcom,ipa: add optional qcom,qmp property
+    - net: ipa: request IPA register values be retained
+    - btrfs: release correct delalloc amount in direct IO write path
+    - ALSA: core: Add snd_card_free_on_error() helper
+    - ALSA: sis7019: Fix the missing error handling
+    - ALSA: ali5451: Fix the missing snd_card_free() call at probe error
+    - ALSA: als300: Fix the missing snd_card_free() call at probe error
+    - ALSA: als4000: Fix the missing snd_card_free() call at probe error
+    - ALSA: atiixp: Fix the missing snd_card_free() call at probe error
+    - ALSA: au88x0: Fix the missing snd_card_free() call at probe error
+    - ALSA: aw2: Fix the missing snd_card_free() call at probe error
+    - ALSA: azt3328: Fix the missing snd_card_free() call at probe error
+    - ALSA: bt87x: Fix the missing snd_card_free() call at probe error
+    - ALSA: ca0106: Fix the missing snd_card_free() call at probe error
+    - ALSA: cmipci: Fix the missing snd_card_free() call at probe error
+    - ALSA: cs4281: Fix the missing snd_card_free() call at probe error
+    - ALSA: cs5535audio: Fix the missing snd_card_free() call at probe error
+    - ALSA: echoaudio: Fix the missing snd_card_free() call at probe error
+    - ALSA: emu10k1x: Fix the missing snd_card_free() call at probe error
+    - ALSA: ens137x: Fix the missing snd_card_free() call at probe error
+    - ALSA: es1938: Fix the missing snd_card_free() call at probe error
+    - ALSA: es1968: Fix the missing snd_card_free() call at probe error
+    - ALSA: fm801: Fix the missing snd_card_free() call at probe error
+    - ALSA: galaxy: Fix the missing snd_card_free() call at probe error
+    - ALSA: hdsp: Fix the missing snd_card_free() call at probe error
+    - ALSA: hdspm: Fix the missing snd_card_free() call at probe error
+    - ALSA: ice1724: Fix the missing snd_card_free() call at probe error
+    - ALSA: intel8x0: Fix the missing snd_card_free() call at probe error
+    - ALSA: intel_hdmi: Fix the missing snd_card_free() call at probe error
+    - ALSA: korg1212: Fix the missing snd_card_free() call at probe error
+    - ALSA: lola: Fix the missing snd_card_free() call at probe error
+    - ALSA: lx6464es: Fix the missing snd_card_free() call at probe error
+    - ALSA: maestro3: Fix the missing snd_card_free() call at probe error
+    - ALSA: oxygen: Fix the missing snd_card_free() call at probe error
+    - ALSA: riptide: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme32: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme9652: Fix the missing snd_card_free() call at probe error
+    - ALSA: rme96: Fix the missing snd_card_free() call at probe error
+    - ALSA: sc6000: Fix the missing snd_card_free() call at probe error
+    - ALSA: sonicvibes: Fix the missing snd_card_free() call at probe error
+    - ALSA: via82xx: Fix the missing snd_card_free() call at probe error
+    - ALSA: usb-audio: Cap upper limits of buffer/period bytes for implicit fb
+    - ALSA: nm256: Don't call card private_free at probe error path
+    - drm/msm: Add missing put_task_struct() in debugfs path
+    - firmware: arm_scmi: Remove clear channel call on the TX channel
+    - memory: atmel-ebi: Fix missing of_node_put in atmel_ebi_probe
+    - Revert "ath11k: mesh: add support for 256 bitmap in blockack frames in 11ax"
+    - firmware: arm_scmi: Fix sorting of retrieved clock rates
+    - media: rockchip/rga: do proper error checking in probe
+    - SUNRPC: Fix the svc_deferred_event trace class
+    - net/sched: flower: fix parsing of ethertype following VLAN header
+    - veth: Ensure eth header is in skb's linear part
+    - gpiolib: acpi: use correct format characters
+    - cifs: release cached dentries only if mount is complete
+    - net: mdio: don't defer probe forever if PHY IRQ provider is missing
+    - mlxsw: i2c: Fix initialization error flow
+    - net/sched: fix initialization order when updating chain 0 head
+    - net: dsa: felix: suppress -EPROBE_DEFER errors
+    - net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link
+    - net/sched: taprio: Check if socket flags are valid
+    - cfg80211: hold bss_lock while updating nontrans_list
+    - netfilter: nft_socket: make cgroup match work in input too
+    - drm/msm: Fix range size vs end confusion
+    - drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()
+    - drm/msm/dp: add fail safe mode outside of event_mutex context
+    - net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
+    - scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
+    - scsi: pm80xx: Enable upper inbound, outbound queues
+    - scsi: iscsi: Move iscsi_ep_disconnect()
+    - scsi: iscsi: Fix offload conn cleanup when iscsid restarts
+    - scsi: iscsi: Fix endpoint reuse regression
+    - scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
+    - scsi: iscsi: Fix unbound endpoint error handling
+    - sctp: Initialize daddr on peeled off socket
+    - netfilter: nf_tables: nft_parse_register can return a negative value
+    - ALSA: ad1889: Fix the missing snd_card_free() call at probe error
+    - ALSA: mtpav: Don't call card private_free at probe error path
+    - io_uring: move io_uring_rsrc_update2 validation
+    - io_uring: verify that resv2 is 0 in io_uring_rsrc_update2
+    - io_uring: verify pad field is 0 in io_get_ext_arg
+    - testing/selftests/mqueue: Fix mq_perf_tests to free the allocated cpu set
+    - ALSA: usb-audio: Increase max buffer size
+    - ALSA: usb-audio: Limit max buffer and period sizes per time
+    - perf tools: Fix misleading add event PMU debug message
+    - macvlan: Fix leaking skb in source mode with nodst option
+    - net: ftgmac100: access hardware register after clock ready
+    - nfc: nci: add flush_workqueue to prevent uaf
+    - cifs: potential buffer overflow in handling symlinks
+    - dm mpath: only use ktime_get_ns() in historical selector
+    - vfio/pci: Fix vf_token mechanism when device-specific VF drivers are used
+    - net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
+    - block: fix offset/size check in bio_trim()
+    - drm/amd: Add USBC connector ID
+    - btrfs: fix fallocate to use file_modified to update permissions consistently
+    - btrfs: do not warn for free space inode in cow_file_range
+    - drm/amdgpu: conduct a proper cleanup of PDB bo
+    - drm/amdgpu/gmc: use PCI BARs for APUs in passthrough
+    - drm/amd/display: fix audio format not updated after edid updated
+    - drm/amd/display: FEC check in timing validation
+    - drm/amd/display: Update VTEM Infopacket definition
+    - drm/amdkfd: Fix Incorrect VMIDs passed to HWS
+    - drm/amdgpu/vcn: improve vcn dpg stop procedure
+    - drm/amdkfd: Check for potential null return of kmalloc_array()
+    - Drivers: hv: vmbus: Deactivate sysctl_record_panic_msg by default in
+      isolated guests
+    - PCI: hv: Propagate coherence from VMbus device to PCI device
+    - Drivers: hv: vmbus: Prevent load re-ordering when reading ring buffer
+    - scsi: target: tcmu: Fix possible page UAF
+    - scsi: lpfc: Fix queue failures when recovering from PCI parity error
+    - scsi: ibmvscsis: Increase INITIAL_SRP_LIMIT to 1024
+    - net: micrel: fix KS8851_MLL Kconfig
+    - ata: libata-core: Disable READ LOG DMA EXT for Samsung 840 EVOs
+    - gpu: ipu-v3: Fix dev_dbg frequency output
+    - regulator: wm8994: Add an off-on delay for WM8994 variant
+    - arm64: alternatives: mark patch_alternative() as `noinstr`
+    - tlb: hugetlb: Add more sizes to tlb_remove_huge_tlb_entry
+    - net: axienet: setup mdio unconditionally
+    - Drivers: hv: balloon: Disable balloon and hot-add accordingly
+    - net: usb: aqc111: Fix out-of-bounds accesses in RX fixup
+    - myri10ge: fix an incorrect free for skb in myri10ge_sw_tso
+    - spi: cadence-quadspi: fix protocol setup for non-1-1-X operations
+    - drm/amd/display: Enable power gating before init_pipes
+    - drm/amd/display: Revert FEC check in validation
+    - drm/amd/display: Fix allocate_mst_payload assert on resume
+    - drbd: set QUEUE_FLAG_STABLE_WRITES
+    - scsi: mpt3sas: Fail reset operation if config request timed out
+    - scsi: mvsas: Add PCI ID of RocketRaid 2640
+    - scsi: megaraid_sas: Target with invalid LUN ID is deleted during scan
+    - drivers: net: slip: fix NPD bug in sl_tx_timeout()
+    - io_uring: zero tag on rsrc removal
+    - io_uring: use nospec annotation for more indexes
+    - perf/imx_ddr: Fix undefined behavior due to shift overflowing the constant
+    - mm/secretmem: fix panic when growing a memfd_secret
+    - mm, page_alloc: fix build_zonerefs_node()
+    - mm: fix unexpected zeroed page mapping with zram swap
+    - mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
+    - KVM: x86/mmu: Resolve nx_huge_pages when kvm.ko is loaded
+    - SUNRPC: Fix NFSD's request deferral on RDMA transports
+    - memory: renesas-rpc-if: fix platform-device leak in error path
+    - gcc-plugins: latent_entropy: use /dev/urandom
+    - cifs: verify that tcon is valid before dereference in cifs_kill_sb
+    - ath9k: Properly clear TX status area before reporting to mac80211
+    - ath9k: Fix usage of driver-private space in tx_info
+    - btrfs: fix root ref counts in error handling in btrfs_get_root_ref
+    - btrfs: mark resumed async balance as writing
+    - ALSA: hda/realtek: Add quirk for Clevo PD50PNT
+    - ALSA: hda/realtek: add quirk for Lenovo Thinkpad X12 speakers
+    - ALSA: pcm: Test for "silence" field in struct "pcm_format_data"
+    - nl80211: correctly check NL80211_ATTR_REG_ALPHA2 size
+    - ipv6: fix panic when forwarding a pkt with no in6 dev
+    - drm/amd/display: don't ignore alpha property on pre-multiplied mode
+    - drm/amdgpu: Enable gfxoff quirk on MacBook Pro
+    - x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits
+    - x86/tsx: Disable TSX development mode at boot
+    - genirq/affinity: Consider that CPUs on nodes can be unbalanced
+    - tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
+    - ARM: davinci: da850-evm: Avoid NULL pointer dereference
+    - dm integrity: fix memory corruption when tag_size is less than digest size
+    - i2c: dev: check return value when calling dev_set_name()
+    - smp: Fix offline cpu check in flush_smp_call_function_queue()
+    - i2c: pasemi: Wait for write xfers to finish
+    - dt-bindings: net: snps: remove duplicate name
+    - timers: Fix warning condition in __run_timers()
+    - dma-direct: avoid redundant memory sync for swiotlb
+    - drm/i915: Sunset igpu legacy mmap support based on GRAPHICS_VER_FULL
+    - cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
+    - soc: qcom: aoss: Fix missing put_device call in qmp_get
+    - net: ipa: fix a build dependency
+    - cpufreq: intel_pstate: ITMT support for overclocked system
+    - ax25: add refcount in ax25_dev to avoid UAF bugs
+    - ax25: fix reference count leaks of ax25_dev
+    - ax25: fix UAF bugs of net_device caused by rebinding operation
+    - ax25: Fix refcount leaks caused by ax25_cb_del()
+    - ax25: fix UAF bug in ax25_send_control()
+    - ax25: fix NPD bug in ax25_disconnect
+    - ax25: Fix NULL pointer dereferences in ax25 timers
+    - ax25: Fix UAF bugs in ax25 timers
+    - Linux 5.15.35
+  * CONFIG_SND_COMPRESS_OFFLOAD missing in jammy/ppc64el kernel config
+    (LP: #1969807)
+    - [Config] updateconfigs for SND_COMPRESS_OFFLOAD (ppc64el)
+  * Micmute LED support for Zbook Fury 16 G9 (LP: #1968892)
+    - ALSA: hda/realtek: Add mute and micmut LED support for Zbook Fury 17 G9
+  * Fix broken HDMI audio on AMD PRO VII after S3 (LP: #1968475)
+    - drm/amdgpu: don't set s3 and s0ix at the same time
+    - drm/amdgpu: Ensure HDA function is suspended before ASIC reset
+  * [Ubuntu 22.04] mpi3mr: Request to include latest bug fixes (LP: #1967116)
+    - scsi: mpi3mr: Clean up mpi3mr_print_ioc_info()
+    - scsi: mpi3mr: Use scnprintf() instead of snprintf()
+    - scsi: mpi3mr: Add debug APIs based on logging_level bits
+    - scsi: mpi3mr: Replace spin_lock() with spin_lock_irqsave()
+    - scsi: mpi3mr: Don't reset IOC if cmnds flush with reset status
+    - scsi: mpi3mr: Update MPI3 headers - part1
+    - scsi: mpi3mr: Update MPI3 headers - part2
+    - scsi: mpi3mr: Add support for PCIe Managed Switch SES device
+    - scsi: mpi3mr: Do access status validation before adding devices
+    - scsi: mpi3mr: Increase internal cmnds timeout to 60s
+    - scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
+    - scsi: mpi3mr: Display IOC firmware package version
+    - scsi: mpi3mr: Fault IOC when internal command gets timeout
+    - scsi: mpi3mr: Code refactor of IOC init - part1
+    - scsi: mpi3mr: Code refactor of IOC init - part2
+    - scsi: mpi3mr: Handle offline FW activation in graceful manner
+    - scsi: mpi3mr: Add IOC reinit function
+    - scsi: mpi3mr: Detect async reset that occurred in firmware
+    - scsi: mpi3mr: Gracefully handle online FW update operation
+    - scsi: mpi3mr: Add Event acknowledgment logic
+    - scsi: mpi3mr: Support Prepare for Reset event
+    - scsi: mpi3mr: Print cable mngnt and temp threshold events
+    - scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
+    - scsi: mpi3mr: Use TM response codes from MPI3 headers
+    - scsi: mpi3mr: Enhanced Task Management Support Reply handling
+    - scsi: mpi3mr: Bump driver version to 8.0.0.61.0
+    - scsi: mpi3mr: Fix some spelling mistakes
+    - scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
+    - scsi: mpi3mr: Fix deadlock while canceling the fw event
+    - scsi: mpi3mr: Fix printing of pending I/O count
+    - scsi: mpi3mr: Update MPI3 headers
+    - scsi: mpi3mr: Fix hibernation issue
+    - scsi: mpi3mr: Fix cmnd getting marked as in use forever
+    - scsi: mpi3mr: Update the copyright year
+    - scsi: mpi3mr: Bump driver version to 8.0.0.68.0
+    - scsi: mpi3mr: Fix flushing !WQ_MEM_RECLAIM events warning
+  * Support AMD P-State cpufreq control mechanism (LP: #1956509)
+    - x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature
+      flag
+    - x86/msr: Add AMD CPPC MSR definitions
+    - ACPI: CPPC: Implement support for SystemIO registers
+    - ACPI: CPPC: Add CPPC enable register function
+    - cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future
+      processors
+    - cpufreq: amd-pstate: Add fast switch function for AMD P-State
+    - cpufreq: amd-pstate: Introduce the support for the processors with shared
+      memory solution
+    - cpufreq: amd-pstate: Add trace for AMD P-State module
+    - cpufreq: amd-pstate: Add boost mode support for AMD P-State
+    - cpufreq: amd-pstate: Add AMD P-State frequencies attributes
+    - cpufreq: amd-pstate: Add AMD P-State performance attributes
+    - Documentation: amd-pstate: Add AMD P-State driver introduction
+    - MAINTAINERS: Add AMD P-State driver maintainer entry
+    - cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
+    - cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
+    - [Config] enable X86_AMD_PSTATE as built-in on amd64
+  * Bolt doesn't work with native USB4 hosts (LP: #1962349)
+    - thunderbolt: Retry DROM reads for more failure scenarios
+    - thunderbolt: Do not resume routers if UID is not set
+    - thunderbolt: Do not make DROM read success compulsory
+    - PCI/ACPI: Allow D3 only if Root Port can signal and wake from D3
+  * linux-image-5.0.0-35-generic breaks checkpointing of container
+    (LP: #1857257) // re-apply missing overlayfs SAUCE patch (LP: #1967924)
+    - SAUCE: overlayfs: fix incorrect mnt_id of files opened from map_files
+  * [Jammy, mlx5, ConnectX-7] add CX7 support for software steering
+    (LP: #1966194)
+    - net/mlx5: DR, Fix vport number data type to u16
+    - net/mlx5: DR, Replace local WIRE_PORT macro with the existing
+      MLX5_VPORT_UPLINK
+    - net/mlx5: DR, Add missing query for vport 0
+    - net/mlx5: DR, Align error messages for failure to obtain vport caps
+    - net/mlx5: DR, Support csum recalculation flow table on SFs
+    - net/mlx5: DR, Add support for SF vports
+    - net/mlx5: DR, Increase supported num of actions to 32
+    - net/mlx5: DR, Fix typo 'offeset' to 'offset'
+    - net/mlx5: DR, init_next_match only if needed
+    - net/mlx5: DR, Add missing string for action type SAMPLER
+    - net/mlx5: DR, Add check for unsupported fields in match param
+    - net/mlx5: Introduce new uplink destination type
+    - net/mlx5: DR, Handle eswitch manager and uplink vports separately
+    - net/mlx5: DR, Fix querying eswitch manager vport for ECPF
+    - net/mlx5: DR, Fix check for unsupported fields in match param
+    - net/mlx5: DR, Fix error flow in creating matcher
+    - net/mlx5: DR, Fix lower case macro prefix "mlx5_" to "MLX5_"
+    - net/mlx5: DR, Remove unused struct member in matcher
+    - net/mlx5: DR, Rename list field in matcher struct to list_node
+    - net/mlx5: DR, Add check for flex parser ID value
+    - net/mlx5: DR, Add missing reserved fields to dr_match_param
+    - net/mlx5: DR, Add support for dumping steering info
+    - net/mlx5: DR, Add support for UPLINK destination type
+    - net/mlx5: DR, Warn on failure to destroy objects due to refcount
+    - net/mlx5: Add misc5 flow table match parameters
+    - net/mlx5: DR, Add misc5 to match_param structs
+    - net/mlx5: DR, Support matching on tunnel headers 0 and 1
+    - net/mlx5: DR, Add support for matching on geneve_tlv_option_0_exist field
+    - net/mlx5: DR, Improve steering for empty or RX/TX-only matchers
+    - net/mlx5: DR, Ignore modify TTL if device doesn't support it
+    - net/mlx5: Set SMFS as a default steering mode if device supports it
+    - net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
+    - net/mlx5: DR, Add support for matching on Internet Header Length (IHL)
+    - net/mlx5: DR, Remove unneeded comments
+    - net/mlx5: DR, Fix handling of different actions on the same STE in STEv1
+    - net/mlx5: DR, Rename action modify fields to reflect naming in HW spec
+    - net/mlx5: DR, Refactor ste_ctx handling for STE v0/1
+    - net/mlx5: Introduce software defined steering capabilities
+    - net/mlx5: DR, Add support for ConnectX-7 steering
+  * alsa: enable the cirrus-logic side-codec to make the speaker output sound
+    (LP: #1965496)
+    - ASoC: cs35l41: CS35L41 Boosted Smart Amplifier
+    - ASoC: cs35l41: Fix use of an uninitialised variable
+    - ASoC: cs35l41: Use regmap_read_poll_timeout to wait for OTP boot
+    - ASoC: cs35l41: Combine adjacent register writes
+    - ASoC: cs35l41: Don't overwrite returned error code
+    - ASoC: cs35l41: Fixup the error messages
+    - ASoC: cs35l41: Fix a bunch of trivial code formating/style issues
+    - misc: cs35l41: Remove unused pdn variable
+    - ASoC: cs35l41: Make cs35l41_remove() return void
+    - ASoC: cs35l41: Change monitor widgets to siggens
+    - ASoC: cs35l41: DSP Support
+    - ASoC: cs35l41: Set the max SPI speed for the whole device
+    - ASoC: cs35l41: Fix link problem
+    - ASoC: cs35l41: Fix undefined reference to core functions
+    - ASoC: cs35l41: Convert tables to shared source code
+    - ASoC: cs35l41: Move cs35l41_otp_unpack to shared code
+    - ASoC: cs35l41: Move power initializations to reg_sequence
+    - ASoC: cs35l41: Create shared function for errata patches
+    - ASoC: cs35l41: Create shared function for setting channels
+    - ASoC: cs35l41: Create shared function for boost configuration
+    - ASoC: cs35l41: Add cs35l51/53 IDs
+    - ASoC: cs35l41: Remove incorrect comment
+    - ASoC: cs35l41: Correct DSP power down
+    - ASoC: cs35l41: Correct handling of some registers in the cache
+    - ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems
+    - ASoC: cs35l41: Update handling of test key registers
+    - ASoC: cs35l41: Add support for hibernate memory retention mode
+    - ALSA: hda: cs35l41: fix double free on error in probe()
+    - ALSA: hda: cs35l41: Avoid overwriting register patch
+    - ALSA: hda: cs35l41: Add calls to newly added test key function
+    - ALSA: hda: cs35l41: Move cs35l41* calls to its own symbol namespace
+    - ALSA: hda: cs35l41: Add missing default cases
+    - ALSA: hda: cs35l41: Make use of the helper function dev_err_probe()
+    - ALSA: hda: cs35l41: Tidyup code
+    - ALSA: hda: cs35l41: Make cs35l41_hda_remove() return void
+    - ALSA: hda/realtek: Add support for Legion 7 16ACHg6 laptop
+    - ALSA: hda/realtek: Add CS35L41 support for Thinkpad laptops
+    - ALSA: hda/realtek: fix speakers and micmute on HP 855 G8
+    - Revert "platform/x86: i2c-multi-instantiate: Don't create platform device
+      for INT3515 ACPI nodes"
+    - spi: Create helper API to lookup ACPI info for spi device
+    - spi: Support selection of the index of the ACPI Spi Resource before alloc
+    - spi: Add API to count spi acpi resources
+    - platform/x86: i2c-multi-instantiate: Rename it for a generic serial driver
+      name
+    - platform/x86: serial-multi-instantiate: Reorganize I2C functions
+    - platform/x86: serial-multi-instantiate: Add SPI support
+    - ALSA: hda/realtek: Add support for HP Laptops
+    - ACPI / scan: Create platform device for CS35L41
+    - [Config] Add cirruslogic side codec support
+  * Use kernel-testing repo from launchpad for ADT tests (LP: #1968016)
+    - [Debian] Use kernel-testing repo from launchpad
+  * Fix ADL, WD22TB4,Dual monitors display resolution can't reach 4K 60hz
+    (LP: #1967986)
+    - drm/i915/display: Remove check for low voltage sku for max dp source rate
+    - drm/i915/intel_combo_phy: Print I/O voltage info
+  * Support different Cirrus audio codec configurations on Dell laptops
+    (LP: #1967988)
+    - ALSA: hda/cs8409: Fix Warlock to use mono mic configuration
+    - ALSA: hda/cs8409: Re-order quirk table into ascending order
+    - ALSA: hda/cs8409: Fix Full Scale Volume setting for all variants
+    - ALSA: hda/cs8409: Support new Warlock MLK Variants
+    - ALSA: hda/cs8409: Disable HSBIAS_SENSE_EN for Cyborg
+    - ALSA: hda/cs8409: Add new Dolphin HW variants
+  * Enable speakup kernel modules to allow the speakup screen reader to function
+    (LP: #1967702)
+    - [Config] CONFIG_SPEAKUP=m
+  * linux: CONFIG_SERIAL_8250_MID=y (LP: #1967338)
+    - [Config] amd64 CONFIG_SERIAL_8250_MID=y
+  * alsa/sdw: Fix the audio issue on a Dell machine without internal mic
+    (LP: #1966841)
+    - ASoC: Intel: soc-acpi: add entries in ADL match table
+  * Jammy update: v5.15.34 upstream stable release (LP: #1969107)
+    - Revert "UBUNTU: SAUCE: Revert "scsi: core: Reallocate device's budget map on
+      queue depth change""
+    - lib/logic_iomem: correct fallback config references
+    - um: fix and optimize xor select template for CONFIG64 and timetravel mode
+    - rtc: wm8350: Handle error for wm8350_register_irq
+    - nbd: add error handling support for add_disk()
+    - nbd: Fix incorrect error handle when first_minor is illegal in nbd_dev_add
+    - nbd: Fix hungtask when nbd_config_put
+    - nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
+    - kfence: count unexpectedly skipped allocations
+    - kfence: move saving stack trace of allocations into __kfence_alloc()
+    - kfence: limit currently covered allocations when pool nearly full
+    - KVM: x86/pmu: Use different raw event masks for AMD and Intel
+    - KVM: SVM: Fix kvm_cache_regs.h inclusions for is_guest_mode()
+    - KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
+    - KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
+    - KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
+    - drm: Add orientation quirk for GPD Win Max
+    - ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111
+    - drm/amd/display: Add signal type check when verify stream backends same
+    - drm/amd/amdgpu/amdgpu_cs: fix refcount leak of a dma_fence obj
+    - drm/amd/display: Fix memory leak
+    - drm/amd/display: Use PSR version selected during set_psr_caps
+    - usb: gadget: tegra-xudc: Do not program SPARAM
+    - usb: gadget: tegra-xudc: Fix control endpoint's definitions
+    - usb: cdnsp: fix cdnsp_decode_trb function to properly handle ret value
+    - ptp: replace snprintf with sysfs_emit
+    - drm/amdkfd: Don't take process mutex for svm ioctls
+    - powerpc: dts: t104xrdb: fix phy type for FMAN 4/5
+    - ath11k: fix kernel panic during unload/load ath11k modules
+    - ath11k: pci: fix crash on suspend if board file is not found
+    - ath11k: mhi: use mhi_sync_power_up()
+    - net/smc: Send directly when TCP_CORK is cleared
+    - drm/bridge: Add missing pm_runtime_put_sync
+    - bpf: Make dst_port field in struct bpf_sock 16-bit wide
+    - scsi: mvsas: Replace snprintf() with sysfs_emit()
+    - scsi: bfa: Replace snprintf() with sysfs_emit()
+    - drm/v3d: fix missing unlock
+    - power: supply: axp20x_battery: properly report current when discharging
+    - mt76: mt7921: fix crash when startup fails.
+    - mt76: dma: initialize skip_unmap in mt76_dma_rx_fill
+    - cfg80211: don't add non transmitted BSS to 6GHz scanned channels
+    - libbpf: Fix build issue with llvm-readelf
+    - ipv6: make mc_forwarding atomic
+    - net: initialize init_net earlier
+    - powerpc: Set crashkernel offset to mid of RMA region
+    - drm/amdgpu: Fix recursive locking warning
+    - scsi: smartpqi: Fix kdump issue when controller is locked up
+    - PCI: aardvark: Fix support for MSI interrupts
+    - iommu/arm-smmu-v3: fix event handling soft lockup
+    - usb: ehci: add pci device support for Aspeed platforms
+    - PCI: endpoint: Fix alignment fault error in copy tests
+    - tcp: Don't acquire inet_listen_hashbucket::lock with disabled BH.
+    - PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
+    - scsi: mpi3mr: Fix reporting of actual data transfer size
+    - scsi: mpi3mr: Fix memory leaks
+    - powerpc/set_memory: Avoid spinlock recursion in change_page_attr()
+    - power: supply: axp288-charger: Set Vhold to 4.4V
+    - net/mlx5e: Disable TX queues before registering the netdev
+    - usb: dwc3: pci: Set the swnode from inside dwc3_pci_quirks()
+    - iwlwifi: mvm: Correctly set fragmented EBS
+    - iwlwifi: mvm: move only to an enabled channel
+    - drm/msm/dsi: Remove spurious IRQF_ONESHOT flag
+    - ipv4: Invalidate neighbour for broadcast address upon address addition
+    - dm ioctl: prevent potential spectre v1 gadget
+    - dm: requeue IO if mapping table not yet available
+    - drm/amdkfd: make CRAT table missing message informational only
+    - vfio/pci: Stub vfio_pci_vga_rw when !CONFIG_VFIO_PCI_VGA
+    - scsi: pm8001: Fix pm80xx_pci_mem_copy() interface
+    - scsi: pm8001: Fix pm8001_mpi_task_abort_resp()
+    - scsi: pm8001: Fix task leak in pm8001_send_abort_all()
+    - scsi: pm8001: Fix tag leaks on error
+    - scsi: pm8001: Fix memory leak in pm8001_chip_fw_flash_update_req()
+    - mt76: mt7915: fix injected MPDU transmission to not use HW A-MSDU
+    - powerpc/64s/hash: Make hash faults work in NMI context
+    - mt76: mt7615: Fix assigning negative values to unsigned variable
+    - scsi: aha152x: Fix aha152x_setup() __setup handler return value
+    - scsi: hisi_sas: Free irq vectors in order for v3 HW
+    - scsi: hisi_sas: Limit users changing debugfs BIST count value
+    - net/smc: correct settings of RMB window update limit
+    - mips: ralink: fix a refcount leak in ill_acc_of_setup()
+    - macvtap: advertise link netns via netlink
+    - tuntap: add sanity checks about msg_controllen in sendmsg
+    - Bluetooth: Fix not checking for valid hdev on bt_dev_{info,warn,err,dbg}
+    - Bluetooth: use memset avoid memory leaks
+    - bnxt_en: Eliminate unintended link toggle during FW reset
+    - PCI: endpoint: Fix misused goto label
+    - MIPS: fix fortify panic when copying asm exception handlers
+    - powerpc/64e: Tie PPC_BOOK3E_64 to PPC_FSL_BOOK3E
+    - powerpc/secvar: fix refcount leak in format_show()
+    - scsi: libfc: Fix use after free in fc_exch_abts_resp()
+    - can: isotp: set default value for N_As to 50 micro seconds
+    - can: etas_es58x: es58x_fd_rx_event_msg(): initialize rx_event_msg before
+      calling es58x_check_msg_len()
+    - riscv: Fixed misaligned memory access. Fixed pointer comparison.
+    - net: account alternate interface name memory
+    - net: limit altnames to 64k total
+    - net/mlx5e: Remove overzealous validations in netlink EEPROM query
+    - net: sfp: add 2500base-X quirk for Lantech SFP module
+    - usb: dwc3: omap: fix "unbalanced disables for smps10_out1" on omap5evm
+    - mt76: fix monitor mode crash with sdio driver
+    - xtensa: fix DTC warning unit_address_format
+    - MIPS: ingenic: correct unit node address
+    - Bluetooth: Fix use after free in hci_send_acl
+    - netfilter: conntrack: revisit gc autotuning
+    - netlabel: fix out-of-bounds memory accesses
+    - ceph: fix inode reference leakage in ceph_get_snapdir()
+    - ceph: fix memory leak in ceph_readdir when note_last_dentry returns error
+    - lib/Kconfig.debug: add ARCH dependency for FUNCTION_ALIGN option
+    - init/main.c: return 1 from handled __setup() functions
+    - minix: fix bug when opening a file with O_DIRECT
+    - clk: si5341: fix reported clk_rate when output divider is 2
+    - staging: vchiq_arm: Avoid NULL ptr deref in vchiq_dump_platform_instances
+    - staging: vchiq_core: handle NULL result of find_service_by_handle
+    - phy: amlogic: phy-meson-gxl-usb2: fix shared reset controller use
+    - phy: amlogic: meson8b-usb2: Use dev_err_probe()
+    - phy: amlogic: meson8b-usb2: fix shared reset control use
+    - clk: rockchip: drop CLK_SET_RATE_PARENT from dclk_vop* on rk3568
+    - cpufreq: CPPC: Fix performance/frequency conversion
+    - opp: Expose of-node's name in debugfs
+    - staging: wfx: fix an error handling in wfx_init_common()
+    - w1: w1_therm: fixes w1_seq for ds28ea00 sensors
+    - NFSv4.2: fix reference count leaks in _nfs42_proc_copy_notify()
+    - NFSv4: Protect the state recovery thread against direct reclaim
+    - habanalabs: fix possible memory leak in MMU DR fini
+    - xen: delay xen_hvm_init_time_ops() if kdump is boot on vcpu>=32
+    - clk: ti: Preserve node in ti_dt_clocks_register()
+    - clk: Enforce that disjoints limits are invalid
+    - SUNRPC/call_alloc: async tasks mustn't block waiting for memory
+    - SUNRPC/xprt: async tasks mustn't block waiting for memory
+    - SUNRPC: remove scheduling boost for "SWAPPER" tasks.
+    - NFS: swap IO handling is slightly different for O_DIRECT IO
+    - NFS: swap-out must always use STABLE writes.
+    - x86: Annotate call_on_stack()
+    - x86/Kconfig: Do not allow CONFIG_X86_X32_ABI=y with llvm-objcopy
+    - serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
+    - virtio_console: eliminate anonymous module_init & module_exit
+    - jfs: prevent NULL deref in diFree
+    - SUNRPC: Fix socket waits for write buffer space
+    - NFS: nfsiod should not block forever in mempool_alloc()
+    - NFS: Avoid writeback threads getting stuck in mempool_alloc()
+    - selftests: net: Add tls config dependency for tls selftests
+    - parisc: Fix CPU affinity for Lasi, WAX and Dino chips
+    - parisc: Fix patch code locking and flushing
+    - mm: fix race between MADV_FREE reclaim and blkdev direct IO read
+    - rtc: mc146818-lib: change return values of mc146818_get_time()
+    - rtc: Check return value from mc146818_get_time()
+    - rtc: mc146818-lib: fix RTC presence check
+    - drm/amdgpu: fix off by one in amdgpu_gfx_kiq_acquire()
+    - Drivers: hv: vmbus: Fix potential crash on module unload
+    - Revert "NFSv4: Handle the special Linux file open access mode"
+    - NFSv4: fix open failure with O_ACCMODE flag
+    - scsi: sr: Fix typo in CDROM(CLOSETRAY|EJECT) handling
+    - scsi: core: Fix sbitmap depth in scsi_realloc_sdev_budget_map()
+    - scsi: zorro7xx: Fix a resource leak in zorro7xx_remove_one()
+    - vdpa/mlx5: Rename control VQ workqueue to vdpa wq
+    - vdpa/mlx5: Propagate link status from device to vdpa driver
+    - vdpa: mlx5: prevent cvq work from hogging CPU
+    - net: sfc: add missing xdp queue reinitialization
+    - net/tls: fix slab-out-of-bounds bug in decrypt_internal
+    - vrf: fix packet sniffing for traffic originating from ip tunnels
+    - skbuff: fix coalescing for page_pool fragment recycling
+    - ice: Clear default forwarding VSI during VSI release
+    - mctp: Fix check for dev_hard_header() result
+    - net: ipv4: fix route with nexthop object delete warning
+    - net: stmmac: Fix unset max_speed difference between DT and non-DT platforms
+    - drm/imx: imx-ldb: Check for null pointer after calling kmemdup
+    - drm/imx: Fix memory leak in imx_pd_connector_get_modes
+    - drm/imx: dw_hdmi-imx: Fix bailout in error cases of probe
+    - regulator: rtq2134: Fix missing active_discharge_on setting
+    - regulator: atc260x: Fix missing active_discharge_on setting
+    - arch/arm64: Fix topology initialization for core scheduling
+    - bnxt_en: Synchronize tx when xdp redirects happen on same ring
+    - bnxt_en: reserve space inside receive page for skb_shared_info
+    - bnxt_en: Prevent XDP redirect from running when stopping TX queue
+    - sfc: Do not free an empty page_ring
+    - RDMA/mlx5: Don't remove cache MRs when a delay is needed
+    - RDMA/mlx5: Add a missing update of cache->last_add
+    - IB/cm: Cancel mad on the DREQ event when the state is MRA_REP_RCVD
+    - IB/rdmavt: add lock to call to rvt_error_qp to prevent a race condition
+    - sctp: count singleton chunks in assoc user stats
+    - dpaa2-ptp: Fix refcount leak in dpaa2_ptp_probe
+    - ice: Set txq_teid to ICE_INVAL_TEID on ring creation
+    - ice: Do not skip not enabled queues in ice_vc_dis_qs_msg
+    - ipv6: Fix stats accounting in ip6_pkt_drop
+    - ice: synchronize_rcu() when terminating rings
+    - ice: xsk: fix VSI state check in ice_xsk_wakeup()
+    - net: openvswitch: don't send internal clone attribute to the userspace.
+    - net: ethernet: mv643xx: Fix over zealous checking of_get_mac_address()
+    - net: openvswitch: fix leak of nested actions
+    - rxrpc: fix a race in rxrpc_exit_net()
+    - net: sfc: fix using uninitialized xdp tx_queue
+    - net: phy: mscc-miim: reject clause 45 register accesses
+    - qede: confirm skb is allocated before using
+    - spi: bcm-qspi: fix MSPI only access with bcm_qspi_exec_mem_op()
+    - bpf: Support dual-stack sockets in bpf_tcp_check_syncookie
+    - drbd: Fix five use after free bugs in get_initial_state
+    - scsi: ufs: ufshpb: Fix a NULL check on list iterator
+    - io_uring: nospec index for tags on files update
+    - io_uring: don't touch scm_fp_list after queueing skb
+    - SUNRPC: Handle ENOMEM in call_transmit_status()
+    - SUNRPC: Handle low memory situations in call_status()
+    - SUNRPC: svc_tcp_sendmsg() should handle errors from xdr_alloc_bvec()
+    - iommu/omap: Fix regression in probe for NULL pointer dereference
+    - perf: arm-spe: Fix perf report --mem-mode
+    - perf tools: Fix perf's libperf_print callback
+    - perf session: Remap buf if there is no space for event
+    - arm64: Add part number for Arm Cortex-A78AE
+    - scsi: mpt3sas: Fix use after free in _scsih_expander_node_remove()
+    - scsi: ufs: ufs-pci: Add support for Intel MTL
+    - Revert "mmc: sdhci-xenon: fix annoying 1.8V regulator warning"
+    - mmc: block: Check for errors after write on SPI
+    - mmc: mmci: stm32: correctly check all elements of sg list
+    - mmc: renesas_sdhi: don't overwrite TAP settings when HS400 tuning is
+      complete
+    - mmc: core: Fixup support for writeback-cache for eMMC and SD
+    - lz4: fix LZ4_decompress_safe_partial read out of bound
+    - highmem: fix checks in __kmap_local_sched_{in,out}
+    - mmmremap.c: avoid pointless invalidate_range_start/end on mremap(old_size=0)
+    - mm/mempolicy: fix mpol_new leak in shared_policy_replace
+    - io_uring: don't check req->file in io_fsync_prep()
+    - io_uring: defer splice/tee file validity check until command issue
+    - io_uring: implement compat handling for IORING_REGISTER_IOWQ_AFF
+    - io_uring: fix race between timeout flush and removal
+    - x86/pm: Save the MSR validity status at context setup
+    - x86/speculation: Restore speculation related MSRs during S3 resume
+    - perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
+    - btrfs: fix qgroup reserve overflow the qgroup limit
+    - btrfs: prevent subvol with swapfile from being deleted
+    - spi: core: add dma_map_dev for __spi_unmap_msg()
+    - arm64: patch_text: Fixup last cpu should be master
+    - RDMA/hfi1: Fix use-after-free bug for mm struct
+    - gpio: Restrict usage of GPIO chip irq members before initialization
+    - x86/msi: Fix msi message data shadow struct
+    - x86/mm/tlb: Revert retpoline avoidance approach
+    - perf/x86/intel: Don't extend the pseudo-encoding to GP counters
+    - ata: sata_dwc_460ex: Fix crash due to OOB write
+    - perf: qcom_l2_pmu: fix an incorrect NULL check on list iterator
+    - perf/core: Inherit event_caps
+    - irqchip/gic-v3: Fix GICR_CTLR.RWP polling
+    - fbdev: Fix unregistering of framebuffers without device
+    - amd/display: set backlight only if required
+    - SUNRPC: Prevent immediate close+reconnect
+    - drm/panel: ili9341: fix optional regulator handling
+    - drm/amdgpu/display: change pipe policy for DCN 2.1
+    - drm/amdgpu/smu10: fix SoC/fclk units in auto mode
+    - drm/amdgpu/vcn: Fix the register setting for vcn1
+    - drm/nouveau/pmu: Add missing callbacks for Tegra devices
+    - drm/amdkfd: Create file descriptor after client is added to smi_clients list
+    - drm/amdgpu: don't use BACO for reset in S3
+    - KVM: SVM: Allow AVIC support on system w/ physical APIC ID > 255
+    - net/smc: send directly on setting TCP_NODELAY
+    - Revert "selftests: net: Add tls config dependency for tls selftests"
+    - bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
+    - selftests/bpf: Fix u8 narrow load checks for bpf_sk_lookup remote_port
+    - rtc: mc146818-lib: fix signedness bug in mc146818_get_time()
+    - SUNRPC: Don't call connect() more than once on a TCP socket
+    - Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"
+    - perf build: Don't use -ffat-lto-objects in the python feature test when
+      building with clang-13
+    - perf python: Fix probing for some clang command line options
+    - tools build: Filter out options and warnings not supported by clang
+    - tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
+    - dmaengine: Revert "dmaengine: shdma: Fix runtime PM imbalance on error"
+    - KVM: avoid NULL pointer dereference in kvm_dirty_ring_push
+    - Revert "net/mlx5: Accept devlink user input after driver initialization
+      complete"
+    - ubsan: remove CONFIG_UBSAN_OBJECT_SIZE
+    - selftests: cgroup: Make cg_create() use 0755 for permission instead of 0644
+    - selftests: cgroup: Test open-time credential usage for migration checks
+    - selftests: cgroup: Test open-time cgroup namespace usage for migration
+      checks
+    - mm: don't skip swap entry even if zap_details specified
+    - Drivers: hv: vmbus: Replace smp_store_mb() with virt_store_mb()
+    - x86/bug: Prevent shadowing in __WARN_FLAGS
+    - sched: Teach the forced-newidle balancer about CPU affinity limitation.
+    - x86,static_call: Fix __static_call_return0 for i386
+    - irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
+    - powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
+    - irqchip/gic, gic-v3: Prevent GSI to SGI translations
+    - mm/sparsemem: fix 'mem_section' will never be NULL gcc 12 warning
+    - static_call: Don't make __static_call_return0 static
+    - powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
+    - stacktrace: move filter_irq_stacks() to kernel/stacktrace.c
+    - Linux 5.15.34
+    - [Config] armhf, s390x: update annotations following
+      DEBUG_FORCE_FUNCTION_ALIGN_64B support removal in v5.15.34
+  * Jammy update: v5.15.33 upstream stable release (LP: #1969110)
+    - Revert "swiotlb: rework "fix info leak with DMA_FROM_DEVICE""
+    - USB: serial: pl2303: add IBM device IDs
+    - dt-bindings: usb: hcd: correct usb-device path
+    - USB: serial: pl2303: fix GS type detection
+    - USB: serial: simple: add Nokia phone driver
+    - mm: kfence: fix missing objcg housekeeping for SLAB
+    - hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
+    - HID: logitech-dj: add new lightspeed receiver id
+    - HID: Add support for open wheel and no attachment to T300
+    - xfrm: fix tunnel model fragmentation behavior
+    - ARM: mstar: Select HAVE_ARM_ARCH_TIMER
+    - virtio_console: break out of buf poll on remove
+    - vdpa/mlx5: should verify CTRL_VQ feature exists for MQ
+    - tools/virtio: fix virtio_test execution
+    - ethernet: sun: Free the coherent when failing in probing
+    - gpio: Revert regression in sysfs-gpio (gpiolib.c)
+    - spi: Fix invalid sgs value
+    - net:mcf8390: Use platform_get_irq() to get the interrupt
+    - Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"
+    - spi: Fix erroneous sgs value with min_t()
+    - Input: zinitix - do not report shadow fingers
+    - af_key: add __GFP_ZERO flag for compose_sadb_supported in function
+      pfkey_register
+    - net: dsa: microchip: add spi_device_id tables
+    - selftests: vm: fix clang build error multiple output files
+    - locking/lockdep: Avoid potential access of invalid memory in lock_class
+    - drm/amdgpu: move PX checking into amdgpu_device_ip_early_init
+    - drm/amdgpu: only check for _PR3 on dGPUs
+    - iommu/iova: Improve 32-bit free space estimate
+    - virtio-blk: Use blk_validate_block_size() to validate block size
+    - tpm: fix reference counting for struct tpm_chip
+    - usb: typec: tipd: Forward plug orientation to typec subsystem
+    - USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
+    - xhci: fix garbage USBSTS being logged in some cases
+    - xhci: fix runtime PM imbalance in USB2 resume
+    - xhci: make xhci_handshake timeout for xhci_reset() adjustable
+    - xhci: fix uninitialized string returned by xhci_decode_ctrl_ctx()
+    - mei: me: disable driver on the ign firmware
+    - mei: me: add Alder Lake N device id.
+    - mei: avoid iterator usage outside of list_for_each_entry
+    - bus: mhi: pci_generic: Add mru_default for Quectel EM1xx series
+    - bus: mhi: Fix MHI DMA structure endianness
+    - docs: sphinx/requirements: Limit jinja2<3.1
+    - coresight: Fix TRCCONFIGR.QE sysfs interface
+    - coresight: syscfg: Fix memleak on registration failure in
+      cscfg_create_device
+    - iio: afe: rescale: use s64 for temporary scale calculations
+    - iio: inkern: apply consumer scale on IIO_VAL_INT cases
+    - iio: inkern: apply consumer scale when no channel scale is available
+    - iio: inkern: make a best effort on offset calculation
+    - greybus: svc: fix an error handling bug in gb_svc_hello()
+    - clk: rockchip: re-add rational best approximation algorithm to the
+      fractional divider
+    - clk: uniphier: Fix fixed-rate initialization
+    - cifs: fix handlecache and multiuser
+    - cifs: we do not need a spinlock around the tree access during umount
+    - KEYS: fix length validation in keyctl_pkey_params_get_2()
+    - KEYS: asymmetric: enforce that sig algo matches key algo
+    - KEYS: asymmetric: properly validate hash_algo and encoding
+    - Documentation: add link to stable release candidate tree
+    - Documentation: update stable tree link
+    - firmware: stratix10-svc: add missing callback parameter on RSU
+    - firmware: sysfb: fix platform-device leak in error path
+    - HID: intel-ish-hid: Use dma_alloc_coherent for firmware update
+    - SUNRPC: avoid race between mod_timer() and del_timer_sync()
+    - NFS: NFSv2/v3 clients should never be setting NFS_CAP_XATTR
+    - NFSD: prevent underflow in nfssvc_decode_writeargs()
+    - NFSD: prevent integer overflow on 32 bit systems
+    - f2fs: fix to unlock page correctly in error path of is_alive()
+    - f2fs: quota: fix loop condition at f2fs_quota_sync()
+    - f2fs: fix to do sanity check on .cp_pack_total_block_count
+    - remoteproc: Fix count check in rproc_coredump_write()
+    - mm/mlock: fix two bugs in user_shm_lock()
+    - pinctrl: ingenic: Fix regmap on X series SoCs
+    - pinctrl: samsung: drop pin banks references on error paths
+    - net: bnxt_ptp: fix compilation error
+    - spi: mxic: Fix the transmit path
+    - mtd: rawnand: protect access to rawnand devices while in suspend
+    - can: ems_usb: ems_usb_start_xmit(): fix double dev_kfree_skb() in error path
+    - can: m_can: m_can_tx_handler(): fix use after free of skb
+    - can: usb_8dev: usb_8dev_start_xmit(): fix double dev_kfree_skb() in error
+      path
+    - jffs2: fix use-after-free in jffs2_clear_xattr_subsystem
+    - jffs2: fix memory leak in jffs2_do_mount_fs
+    - jffs2: fix memory leak in jffs2_scan_medium
+    - mm: fs: fix lru_cache_disabled race in bh_lru
+    - mm/pages_alloc.c: don't create ZONE_MOVABLE beyond the end of a node
+    - mm: invalidate hwpoison page cache page in fault path
+    - mempolicy: mbind_range() set_policy() after vma_merge()
+    - scsi: core: sd: Add silence_suspend flag to suppress some PM messages
+    - scsi: ufs: Fix runtime PM messages never-ending cycle
+    - scsi: scsi_transport_fc: Fix FPIN Link Integrity statistics counters
+    - scsi: libsas: Fix sas_ata_qc_issue() handling of NCQ NON DATA commands
+    - qed: display VF trust config
+    - qed: validate and restrict untrusted VFs vlan promisc mode
+    - riscv: dts: canaan: Fix SPI3 bus width
+    - riscv: Fix fill_callchain return value
+    - riscv: Increase stack size under KASAN
+    - Revert "Input: clear BTN_RIGHT/MIDDLE on buttonpads"
+    - cifs: prevent bad output lengths in smb2_ioctl_query_info()
+    - cifs: fix NULL ptr dereference in smb2_ioctl_query_info()
+    - ALSA: cs4236: fix an incorrect NULL check on list iterator
+    - ALSA: hda: Avoid unsol event during RPM suspending
+    - ALSA: pcm: Fix potential AB/BA lock with buffer_mutex and mmap_lock
+    - ALSA: hda/realtek: Fix audio regression on Mi Notebook Pro 2020
+    - rtc: mc146818-lib: fix locking in mc146818_set_time
+    - rtc: pl031: fix rtc features null pointer dereference
+    - ocfs2: fix crash when mount with quota enabled
+    - drm/simpledrm: Add "panel orientation" property on non-upright mounted LCD
+      panels
+    - mm: madvise: skip unmapped vma holes passed to process_madvise
+    - mm: madvise: return correct bytes advised with process_madvise
+    - Revert "mm: madvise: skip unmapped vma holes passed to process_madvise"
+    - mm,hwpoison: unmap poisoned page before invalidation
+    - mm/kmemleak: reset tag when compare object pointer
+    - dm stats: fix too short end duration_ns when using precise_timestamps
+    - dm: fix use-after-free in dm_cleanup_zoned_dev()
+    - dm: interlock pending dm_io and dm_wait_for_bios_completion
+    - dm: fix double accounting of flush with data
+    - dm integrity: set journal entry unused when shrinking device
+    - tracing: Have trace event string test handle zero length strings
+    - drbd: fix potential silent data corruption
+    - powerpc/kvm: Fix kvm_use_magic_page
+    - PCI: fu740: Force 2.5GT/s for initial device probe
+    - arm64: signal: nofpsimd: Do not allocate fp/simd context when not available
+    - arm64: Do not defer reserve_crashkernel() for platforms with no DMA memory
+      zones
+    - arm64: dts: qcom: sm8250: Fix MSI IRQ for PCIe1 and PCIe2
+    - arm64: dts: ti: k3-am65: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-j721e: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-j7200: Fix gic-v3 compatible regs
+    - arm64: dts: ti: k3-am64: Fix gic-v3 compatible regs
+    - ASoC: SOF: Intel: Fix NULL ptr dereference when ENOMEM
+    - Revert "ACPI: Pass the same capabilities to the _OSC regardless of the query
+      flag"
+    - ACPI: properties: Consistently return -ENOENT if there are no more
+      references
+    - coredump: Also dump first pages of non-executable ELF libraries
+    - ext4: fix ext4_fc_stats trace point
+    - ext4: fix fs corruption when tring to remove a non-empty directory with IO
+      error
+    - ext4: make mb_optimize_scan performance mount option work with extents
+    - drivers: hamradio: 6pack: fix UAF bug caused by mod_timer()
+    - samples/landlock: Fix path_list memory leak
+    - landlock: Use square brackets around "landlock-ruleset"
+    - mailbox: tegra-hsp: Flush whole channel
+    - block: limit request dispatch loop duration
+    - block: don't merge across cgroup boundaries if blkcg is enabled
+    - drm/edid: check basic audio support on CEA extension block
+    - fbdev: Hot-unplug firmware fb devices on forced removal
+    - video: fbdev: sm712fb: Fix crash in smtcfb_read()
+    - video: fbdev: atari: Atari 2 bpp (STe) palette bugfix
+    - rfkill: make new event layout opt-in
+    - ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
+    - ARM: dts: at91: sama5d2: Fix PMERRLOC resource size
+    - ARM: dts: exynos: fix UART3 pins configuration in Exynos5250
+    - ARM: dts: exynos: add missing HDMI supplies on SMDK5250
+    - ARM: dts: exynos: add missing HDMI supplies on SMDK5420
+    - mgag200 fix memmapsl configuration in GCTL6 register
+    - carl9170: fix missing bit-wise or operator for tx_params
+    - pstore: Don't use semaphores in always-atomic-context code
+    - thermal: int340x: Increase bitmap size
+    - lib/raid6/test: fix multiple definition linking error
+    - exec: Force single empty string when argv is empty
+    - crypto: rsa-pkcs1pad - only allow with rsa
+    - crypto: rsa-pkcs1pad - correctly get hash from source scatterlist
+    - crypto: rsa-pkcs1pad - restore signature length check
+    - crypto: rsa-pkcs1pad - fix buffer overread in pkcs1pad_verify_complete()
+    - bcache: fixup multiple threads crash
+    - PM: domains: Fix sleep-in-atomic bug caused by genpd_debug_remove()
+    - DEC: Limit PMAX memory probing to R3k systems
+    - media: gpio-ir-tx: fix transmit with long spaces on Orange Pi PC
+    - media: venus: hfi_cmds: List HDR10 property as unsupported for v1 and v3
+    - media: venus: venc: Fix h264 8x8 transform control
+    - media: davinci: vpif: fix unbalanced runtime PM get
+    - media: davinci: vpif: fix unbalanced runtime PM enable
+    - btrfs: zoned: mark relocation as writing
+    - btrfs: extend locking to all space_info members accesses
+    - btrfs: verify the tranisd of the to-be-written dirty extent buffer
+    - xtensa: define update_mmu_tlb function
+    - xtensa: fix stop_machine_cpuslocked call in patch_text
+    - xtensa: fix xtensa_wsr always writing 0
+    - drm/syncobj: flatten dma_fence_chains on transfer
+    - drm/nouveau/backlight: Fix LVDS backlight detection on some laptops
+    - drm/nouveau/backlight: Just set all backlight types as RAW
+    - drm/fb-helper: Mark screen buffers in system memory with FBINFO_VIRTFB
+    - brcmfmac: firmware: Allocate space for default boardrev in nvram
+    - brcmfmac: pcie: Release firmwares in the brcmf_pcie_setup error path
+    - brcmfmac: pcie: Declare missing firmware files in pcie.c
+    - brcmfmac: pcie: Replace brcmf_pcie_copy_mem_todev with memcpy_toio
+    - brcmfmac: pcie: Fix crashes due to early IRQs
+    - drm/i915/opregion: check port number bounds for SWSCI display power state
+    - drm/i915/gem: add missing boundary check in vm_access
+    - PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
+    - PCI: pciehp: Clear cmd_busy bit in polling mode
+    - PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
+    - regulator: qcom_smd: fix for_each_child.cocci warnings
+    - selinux: access superblock_security_struct in LSM blob way
+    - selinux: check return value of sel_make_avc_files
+    - crypto: ccp - Ensure psp_ret is always init'd in
+      __sev_platform_init_locked()
+    - hwrng: cavium - Check health status while reading random data
+    - hwrng: cavium - HW_RANDOM_CAVIUM should depend on ARCH_THUNDER
+    - crypto: sun8i-ss - really disable hash on A80
+    - crypto: authenc - Fix sleep in atomic context in decrypt_tail
+    - crypto: mxs-dcp - Fix scatterlist processing
+    - selinux: Fix selinux_sb_mnt_opts_compat()
+    - thermal: int340x: Check for NULL after calling kmemdup()
+    - crypto: octeontx2 - remove CONFIG_DM_CRYPT check
+    - spi: tegra114: Add missing IRQ check in tegra_spi_probe
+    - spi: tegra210-quad: Fix missin IRQ check in tegra_qspi_probe
+    - stack: Constrain and fix stack offset randomization with Clang builds
+    - arm64/mm: avoid fixmap race condition when create pud mapping
+    - blk-cgroup: set blkg iostat after percpu stat aggregation
+    - selftests/x86: Add validity check and allow field splitting
+    - selftests/sgx: Treat CC as one argument
+    - crypto: rockchip - ECB does not need IV
+    - audit: log AUDIT_TIME_* records only from rules
+    - EVM: fix the evm= __setup handler return value
+    - crypto: ccree - don't attempt 0 len DMA mappings
+    - crypto: hisilicon/sec - fix the aead software fallback for engine
+    - spi: pxa2xx-pci: Balance reference count for PCI DMA device
+    - hwmon: (pmbus) Add mutex to regulator ops
+    - hwmon: (sch56xx-common) Replace WDOG_ACTIVE with WDOG_HW_RUNNING
+    - nvme: cleanup __nvme_check_ids
+    - nvme: fix the check for duplicate unique identifiers
+    - block: don't delete queue kobject before its children
+    - PM: hibernate: fix __setup handler error handling
+    - PM: suspend: fix return value of __setup handler
+    - spi: spi-zynqmp-gqspi: Handle error for dma_set_mask
+    - hwrng: atmel - disable trng on failure path
+    - crypto: sun8i-ss - call finalize with bh disabled
+    - crypto: sun8i-ce - call finalize with bh disabled
+    - crypto: amlogic - call finalize with bh disabled
+    - crypto: gemini - call finalize with bh disabled
+    - crypto: vmx - add missing dependencies
+    - clocksource/drivers/timer-ti-dm: Fix regression from errata i940 fix
+    - clocksource/drivers/exynos_mct: Refactor resources allocation
+    - clocksource/drivers/exynos_mct: Handle DTS with higher number of interrupts
+    - clocksource/drivers/timer-microchip-pit64b: Use notrace
+    - clocksource/drivers/timer-of: Check return value of of_iomap in
+      timer_of_base_init()
+    - arm64: prevent instrumentation of bp hardening callbacks
+    - KEYS: trusted: Fix trusted key backends when building as module
+    - KEYS: trusted: Avoid calling null function trusted_key_exit
+    - ACPI: APEI: fix return value of __setup handlers
+    - crypto: ccp - ccp_dmaengine_unregister release dma channels
+    - crypto: ccree - Fix use after free in cc_cipher_exit()
+    - hwrng: nomadik - Change clk_disable to clk_disable_unprepare
+    - hwmon: (pmbus) Add Vin unit off handling
+    - clocksource: acpi_pm: fix return value of __setup handler
+    - io_uring: don't check unrelated req->open.how in accept request
+    - io_uring: terminate manual loop iterator loop correctly for non-vecs
+    - watch_queue: Fix NULL dereference in error cleanup
+    - watch_queue: Actually free the watch
+    - f2fs: fix to enable ATGC correctly via gc_idle sysfs interface
+    - sched/debug: Remove mpol_get/put and task_lock/unlock from sched_show_numa
+    - sched/core: Export pelt_thermal_tp
+    - sched/uclamp: Fix iowait boost escaping uclamp restriction
+    - rseq: Remove broken uapi field layout on 32-bit little endian
+    - perf/core: Fix address filter parser for multiple filters
+    - perf/x86/intel/pt: Fix address filter config for 32-bit kernel
+    - sched/fair: Improve consistency of allowed NUMA balance calculations
+    - f2fs: fix missing free nid in f2fs_handle_failed_inode
+    - nfsd: more robust allocation failure handling in nfsd_file_cache_init
+    - sched/cpuacct: Fix charge percpu cpuusage
+    - sched/rt: Plug rt_mutex_setprio() vs push_rt_task() race
+    - f2fs: fix to avoid potential deadlock
+    - btrfs: fix unexpected error path when reflinking an inline extent
+    - f2fs: fix compressed file start atomic write may cause data corruption
+    - selftests, x86: fix how check_cc.sh is being invoked
+    - drivers/base/memory: add memory block to memory group after registration
+      succeeded
+    - kunit: make kunit_test_timeout compatible with comment
+    - pinctrl: samsung: Remove EINT handler for Exynos850 ALIVE and CMGP gpios
+    - media: staging: media: zoran: fix usage of vb2_dma_contig_set_max_seg_size
+    - media: camss: csid-170: fix non-10bit formats
+    - media: camss: csid-170: don't enable unused irqs
+    - media: camss: csid-170: set the right HALT_CMD when disabled
+    - media: camss: vfe-170: fix "VFE halt timeout" error
+    - media: staging: media: imx: imx7-mipi-csis: Make subdev name unique
+    - media: v4l2-mem2mem: Apply DST_QUEUE_OFF_BASE on MMAP buffers across ioctls
+    - media: mtk-vcodec: potential dereference of null pointer
+    - media: imx: imx8mq-mipi-csi2: remove wrong irq config write operation
+    - media: imx: imx8mq-mipi_csi2: fix system resume
+    - media: bttv: fix WARNING regression on tunerless devices
+    - media: atmel: atmel-sama7g5-isc: fix ispck leftover
+    - ASoC: sh: rz-ssi: Drop calling rz_ssi_pio_recv() recursively
+    - ASoC: codecs: Check for error pointer after calling devm_regmap_init_mmio
+    - ASoC: xilinx: xlnx_formatter_pcm: Handle sysclk setting
+    - ASoC: simple-card-utils: Set sysclk on all components
+    - media: coda: Fix missing put_device() call in coda_get_vdoa_data
+    - media: meson: vdec: potential dereference of null pointer
+    - media: hantro: Fix overfill bottom register field name
+    - media: ov6650: Fix set format try processing path
+    - media: v4l: Avoid unaligned access warnings when printing 4cc modifiers
+    - media: ov5648: Don't pack controls struct
+    - media: aspeed: Correct value for h-total-pixels
+    - video: fbdev: matroxfb: set maxvram of vbG200eW to the same as vbG200 to
+      avoid black screen
+    - video: fbdev: controlfb: Fix COMPILE_TEST build
+    - video: fbdev: smscufx: Fix null-ptr-deref in ufx_usb_probe()
+    - video: fbdev: atmel_lcdfb: fix an error code in atmel_lcdfb_probe()
+    - video: fbdev: fbcvt.c: fix printing in fb_cvt_print_name()
+    - ARM: dts: Fix OpenBMC flash layout label addresses
+    - firmware: qcom: scm: Remove reassignment to desc following initializer
+    - ARM: dts: qcom: ipq4019: fix sleep clock
+    - soc: qcom: rpmpd: Check for null return of devm_kcalloc
+    - soc: qcom: ocmem: Fix missing put_device() call in of_get_ocmem
+    - soc: qcom: aoss: remove spurious IRQF_ONESHOT flags
+    - arm64: dts: qcom: sdm845: fix microphone bias properties and values
+    - arm64: dts: qcom: sm8250: fix PCIe bindings to follow schema
+    - arm64: dts: broadcom: bcm4908: use proper TWD binding
+    - arm64: dts: qcom: sm8150: Correct TCS configuration for apps rsc
+    - arm64: dts: qcom: sm8350: Correct TCS configuration for apps rsc
+    - firmware: ti_sci: Fix compilation failure when CONFIG_TI_SCI_PROTOCOL is not
+      defined
+    - soc: ti: wkup_m3_ipc: Fix IRQ check in wkup_m3_ipc_probe
+    - ARM: dts: sun8i: v3s: Move the csi1 block to follow address order
+    - vsprintf: Fix potential unaligned access
+    - ARM: dts: imx: Add missing LVDS decoder on M53Menlo
+    - media: mexon-ge2d: fixup frames size in registers
+    - media: video/hdmi: handle short reads of hdmi info frame.
+    - media: ti-vpe: cal: Fix a NULL pointer dereference in
+      cal_ctx_v4l2_init_formats()
+    - media: em28xx: initialize refcount before kref_get
+    - media: usb: go7007: s2250-board: fix leak in probe()
+    - media: cedrus: H265: Fix neighbour info buffer size
+    - media: cedrus: h264: Fix neighbour info buffer size
+    - ASoC: codecs: rx-macro: fix accessing compander for aux
+    - ASoC: codecs: rx-macro: fix accessing array out of bounds for enum type
+    - ASoC: codecs: va-macro: fix accessing array out of bounds for enum type
+    - ASoC: codecs: wc938x: fix accessing array out of bounds for enum type
+    - ASoC: codecs: wcd938x: fix kcontrol max values
+    - ASoC: codecs: wcd934x: fix kcontrol max values
+    - ASoC: codecs: wcd934x: fix return value of wcd934x_rx_hph_mode_put
+    - media: v4l2-core: Initialize h264 scaling matrix
+    - media: ov5640: Fix set format, v4l2_mbus_pixelcode not updated
+    - selftests/lkdtm: Add UBSAN config
+    - lib: uninline simple_strntoull() as well
+    - vsprintf: Fix %pK with kptr_restrict == 0
+    - uaccess: fix nios2 and microblaze get_user_8()
+    - ASoC: rt5663: check the return value of devm_kzalloc() in rt5663_parse_dp()
+    - soc: mediatek: pm-domains: Add wakeup capacity support in power domain
+    - mmc: sdhci_am654: Fix the driver data of AM64 SoC
+    - ASoC: ti: davinci-i2s: Add check for clk_enable()
+    - ALSA: spi: Add check for clk_enable()
+    - arm64: dts: ns2: Fix spi-cpol and spi-cpha property
+    - arm64: dts: broadcom: Fix sata nodename
+    - printk: fix return value of printk.devkmsg __setup handler
+    - ASoC: mxs-saif: Handle errors for clk_enable
+    - ASoC: atmel_ssc_dai: Handle errors for clk_enable
+    - ASoC: dwc-i2s: Handle errors for clk_enable
+    - ASoC: soc-compress: prevent the potentially use of null pointer
+    - memory: emif: Add check for setup_interrupts
+    - memory: emif: check the pointer temp in get_device_details()
+    - ALSA: firewire-lib: fix uninitialized flag for AV/C deferred transaction
+    - arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
+    - m68k: coldfire/device.c: only build for MCF_EDMA when h/w macros are defined
+    - media: stk1160: If start stream fails, return buffers with
+      VB2_BUF_STATE_QUEUED
+    - media: vidtv: Check for null return of vzalloc
+    - ASoC: atmel: Add missing of_node_put() in at91sam9g20ek_audio_probe
+    - ASoC: wm8350: Handle error for wm8350_register_irq
+    - ASoC: fsi: Add check for clk_enable
+    - video: fbdev: omapfb: Add missing of_node_put() in dvic_probe_of
+    - media: saa7134: fix incorrect use to determine if list is empty
+    - ivtv: fix incorrect device_caps for ivtvfb
+    - ASoC: atmel: Fix error handling in snd_proto_probe
+    - ASoC: rockchip: i2s: Fix missing clk_disable_unprepare() in
+      rockchip_i2s_probe
+    - ASoC: SOF: Add missing of_node_put() in imx8m_probe
+    - ASoC: mediatek: use of_device_get_match_data()
+    - ASoC: mediatek: mt8192-mt6359: Fix error handling in mt8192_mt6359_dev_probe
+    - ASoC: rk817: Fix missing clk_disable_unprepare() in rk817_platform_probe
+    - ASoC: dmaengine: do not use a NULL prepare_slave_config() callback
+    - ASoC: mxs: Fix error handling in mxs_sgtl5000_probe
+    - ASoC: fsl_spdif: Disable TX clock when stop
+    - ASoC: imx-es8328: Fix error return code in imx_es8328_probe()
+    - ASoC: SOF: Intel: enable DMI L1 for playback streams
+    - ASoC: msm8916-wcd-digital: Fix missing clk_disable_unprepare() in
+      msm8916_wcd_digital_probe
+    - mmc: davinci_mmc: Handle error for clk_enable
+    - ASoC: atmel: Fix error handling in sam9x5_wm8731_driver_probe
+    - ASoC: msm8916-wcd-analog: Fix error handling in pm8916_wcd_analog_spmi_probe
+    - ASoC: codecs: wcd934x: Add missing of_node_put() in wcd934x_codec_parse_data
+    - ASoC: amd: Fix reference to PCM buffer address
+    - ARM: configs: multi_v5_defconfig: re-enable CONFIG_V4L_PLATFORM_DRIVERS
+    - ARM: configs: multi_v5_defconfig: re-enable DRM_PANEL and FB_xxx
+    - drm/meson: osd_afbcd: Add an exit callback to struct meson_afbcd_ops
+    - drm/meson: Make use of the helper function
+      devm_platform_ioremap_resourcexxx()
+    - drm/meson: split out encoder from meson_dw_hdmi
+    - drm/meson: Fix error handling when afbcd.ops->init fails
+    - drm/bridge: Fix free wrong object in sii8620_init_rcp_input_dev
+    - drm/bridge: Add missing pm_runtime_disable() in __dw_mipi_dsi_probe
+    - drm/bridge: nwl-dsi: Fix PM disable depth imbalance in nwl_dsi_probe
+    - drm: bridge: adv7511: Fix ADV7535 HPD enablement
+    - ath10k: fix memory overwrite of the WoWLAN wakeup packet pattern
+    - drm/v3d/v3d_drv: Check for error num after setting mask
+    - drm/panfrost: Check for error num after setting mask
+    - libbpf: Fix possible NULL pointer dereference when destroying skeleton
+    - bpftool: Only set obj->skeleton on complete success
+    - udmabuf: validate ubuf->pagecount
+    - bpf: Fix UAF due to race between btf_try_get_module and load_module
+    - drm/selftests/test-drm_dp_mst_helper: Fix memory leak in
+      sideband_msg_req_encode_decode
+    - selftests: bpf: Fix bind on used port
+    - Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
+    - Bluetooth: hci_serdev: call init_rwsem() before p->open()
+    - mtd: onenand: Check for error irq
+    - mtd: rawnand: gpmi: fix controller timings setting
+    - drm/edid: Don't clear formats if using deep color
+    - drm/edid: Split deep color modes between RGB and YUV444
+    - ionic: fix type complaint in ionic_dev_cmd_clean()
+    - ionic: start watchdog after all is setup
+    - ionic: Don't send reset commands if FW isn't running
+    - drm/nouveau/acr: Fix undefined behavior in nvkm_acr_hsfw_load_bl()
+    - drm/amd/display: Fix a NULL pointer dereference in
+      amdgpu_dm_connector_add_common_modes()
+    - drm/amd/pm: return -ENOTSUPP if there is no get_dpm_ultimate_freq function
+    - net: phy: at803x: move page selection fix to config_init
+    - selftests/bpf: Normalize XDP section names in selftests
+    - selftests/bpf/test_xdp_redirect_multi: use temp netns for testing
+    - ath9k_htc: fix uninit value bugs
+    - RDMA/core: Set MR type in ib_reg_user_mr
+    - KVM: PPC: Fix vmx/vsx mixup in mmio emulation
+    - selftests/net: timestamping: Fix bind_phc check
+    - i40e: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - i40e: respect metadata on XSK Rx to skb
+    - igc: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - ixgbe: pass bi->xdp to ixgbe_construct_skb_zc() directly
+    - ixgbe: don't reserve excessive XDP_PACKET_HEADROOM on XSK Rx to skb
+    - ixgbe: respect metadata on XSK Rx to skb
+    - power: reset: gemini-poweroff: Fix IRQ check in gemini_poweroff_probe
+    - ray_cs: Check ioremap return value
+    - powerpc: dts: t1040rdb: fix ports names for Seville Ethernet switch
+    - KVM: PPC: Book3S HV: Check return value of kvmppc_radix_init
+    - powerpc/perf: Don't use perf_hw_context for trace IMC PMU
+    - mt76: connac: fix sta_rec_wtbl tag len
+    - mt76: mt7915: use proper aid value in mt7915_mcu_wtbl_generic_tlv in sta
+      mode
+    - mt76: mt7915: use proper aid value in mt7915_mcu_sta_basic_tlv
+    - mt76: mt7921: fix a leftover race in runtime-pm
+    - mt76: mt7615: fix a leftover race in runtime-pm
+    - mt76: mt7603: check sta_rates pointer in mt7603_sta_rate_tbl_update
+    - mt76: mt7615: check sta_rates pointer in mt7615_sta_rate_tbl_update
+    - ptp: unregister virtual clocks when unregistering physical clock.
+    - net: dsa: mv88e6xxx: Enable port policy support on 6097
+    - mac80211: Remove a couple of obsolete TODO
+    - mac80211: limit bandwidth in HE capabilities
+    - scripts/dtc: Call pkg-config POSIXly correct
+    - livepatch: Fix build failure on 32 bits processors
+    - net: asix: add proper error handling of usb read errors
+    - i2c: bcm2835: Use platform_get_irq() to get the interrupt
+    - i2c: bcm2835: Fix the error handling in 'bcm2835_i2c_probe()'
+    - mtd: mchp23k256: Add SPI ID table
+    - mtd: mchp48l640: Add SPI ID table
+    - igc: avoid kernel warning when changing RX ring parameters
+    - igb: refactor XDP registration
+    - PCI: aardvark: Fix reading MSI interrupt number
+    - PCI: aardvark: Fix reading PCI_EXP_RTSTA_PME bit on emulated bridge
+    - RDMA/rxe: Check the last packet by RXE_END_MASK
+    - libbpf: Fix signedness bug in btf_dump_array_data()
+    - cxl/core: Fix cxl_probe_component_regs() error message
+    - cxl/regs: Fix size of CXL Capability Header Register
+    - net:enetc: allocate CBD ring data memory using DMA coherent methods
+    - libbpf: Fix compilation warning due to mismatched printf format
+    - drm/bridge: dw-hdmi: use safe format when first in bridge chain
+    - libbpf: Use dynamically allocated buffer when receiving netlink messages
+    - power: supply: ab8500: Fix memory leak in ab8500_fg_sysfs_init
+    - HID: i2c-hid: fix GET/SET_REPORT for unnumbered reports
+    - iommu/ipmmu-vmsa: Check for error num after setting mask
+    - drm/bridge: anx7625: Fix overflow issue on reading EDID
+    - bpftool: Fix the error when lookup in no-btf maps
+    - drm/amd/pm: enable pm sysfs write for one VF mode
+    - drm/amd/display: Add affected crtcs to atomic state for dsc mst unplug
+    - libbpf: Fix memleak in libbpf_netlink_recv()
+    - IB/cma: Allow XRC INI QPs to set their local ACK timeout
+    - dax: make sure inodes are flushed before destroy cache
+    - selftests: mptcp: add csum mib check for mptcp_connect
+    - iwlwifi: mvm: Don't call iwl_mvm_sta_from_mac80211() with NULL sta
+    - iwlwifi: mvm: don't iterate unadded vifs when handling FW SMPS req
+    - iwlwifi: mvm: align locking in D3 test debugfs
+    - iwlwifi: yoyo: remove DBGI_SRAM address reset writing
+    - iwlwifi: Fix -EIO error code that is never returned
+    - iwlwifi: mvm: Fix an error code in iwl_mvm_up()
+    - mtd: rawnand: pl353: Set the nand chip node as the flash node
+    - drm/msm/dp: populate connector of struct dp_panel
+    - drm/msm/dp: stop link training after link training 2 failed
+    - drm/msm/dp: always add fail-safe mode into connector mode list
+    - drm/msm/dsi: Use "ref" fw clock instead of global name for VCO parent
+    - drm/msm/dsi/phy: fix 7nm v4.0 settings for C-PHY mode
+    - drm/msm/dpu: add DSPP blocks teardown
+    - drm/msm/dpu: fix dp audio condition
+    - dm crypt: fix get_key_size compiler warning if !CONFIG_KEYS
+    - vfio/pci: fix memory leak during D3hot to D0 transition
+    - vfio/pci: wake-up devices around reset functions
+    - scsi: fnic: Fix a tracing statement
+    - scsi: pm8001: Fix command initialization in pm80XX_send_read_log()
+    - scsi: pm8001: Fix command initialization in pm8001_chip_ssp_tm_req()
+    - scsi: pm8001: Fix payload initialization in pm80xx_set_thermal_config()
+    - scsi: pm8001: Fix le32 values handling in
+      pm80xx_set_sas_protocol_timer_config()
+    - scsi: pm8001: Fix payload initialization in pm80xx_encrypt_update()
+    - scsi: pm8001: Fix le32 values handling in pm80xx_chip_ssp_io_req()
+    - scsi: pm8001: Fix le32 values handling in pm80xx_chip_sata_req()
+    - scsi: pm8001: Fix NCQ NON DATA command task initialization
+    - scsi: pm8001: Fix NCQ NON DATA command completion handling
+    - scsi: pm8001: Fix abort all task initialization
+    - RDMA/mlx5: Fix the flow of a miss in the allocation of a cache ODP MR
+    - drm/amd/display: Remove vupdate_int_entry definition
+    - TOMOYO: fix __setup handlers return values
+    - power: supply: sbs-charger: Don't cancel work that is not initialized
+    - ext2: correct max file size computing
+    - drm/tegra: Fix reference leak in tegra_dsi_ganged_probe
+    - power: supply: bq24190_charger: Fix bq24190_vbus_is_enabled() wrong false
+      return
+    - scsi: hisi_sas: Change permission of parameter prot_mask
+    - drm/bridge: cdns-dsi: Make sure to to create proper aliases for dt
+    - bpf, arm64: Call build_prologue() first in first JIT pass
+    - bpf, arm64: Feed byte-offset into bpf line info
+    - xsk: Fix race at socket teardown
+    - RDMA/irdma: Fix netdev notifications for vlan's
+    - RDMA/irdma: Fix Passthrough mode in VM
+    - RDMA/irdma: Remove incorrect masking of PD
+    - gpu: host1x: Fix a memory leak in 'host1x_remove()'
+    - libbpf: Skip forward declaration when counting duplicated type names
+    - powerpc/mm/numa: skip NUMA_NO_NODE onlining in parse_numa_properties()
+    - powerpc/Makefile: Don't pass -mcpu=powerpc64 when building 32-bit
+    - KVM: x86: Fix emulation in writing cr8
+    - KVM: x86/emulator: Defer not-present segment check in
+      __load_segment_descriptor()
+    - hv_balloon: rate-limit "Unhandled message" warning
+    - i2c: xiic: Make bus names unique
+    - power: supply: wm8350-power: Handle error for wm8350_register_irq
+    - power: supply: wm8350-power: Add missing free in free_charger_irq
+    - IB/hfi1: Allow larger MTU without AIP
+    - RDMA/core: Fix ib_qp_usecnt_dec() called when error
+    - PCI: Reduce warnings on possible RW1C corruption
+    - net: axienet: fix RX ring refill allocation failure handling
+    - drm/msm/a6xx: Fix missing ARRAY_SIZE() check
+    - mips: DEC: honor CONFIG_MIPS_FP_SUPPORT=n
+    - MIPS: Sanitise Cavium switch cases in TLB handler synthesizers
+    - powerpc/sysdev: fix incorrect use to determine if list is empty
+    - powerpc/64s: Don't use DSISR for SLB faults
+    - mfd: mc13xxx: Add check for mc13xxx_irq_request
+    - libbpf: Unmap rings when umem deleted
+    - selftests/bpf: Make test_lwt_ip_encap more stable and faster
+    - platform/x86: huawei-wmi: check the return value of device_create_file()
+    - scsi: mpt3sas: Fix incorrect 4GB boundary check
+    - powerpc: 8xx: fix a return value error in mpc8xx_pic_init
+    - vxcan: enable local echo for sent CAN frames
+    - ath10k: Fix error handling in ath10k_setup_msa_resources
+    - mips: cdmm: Fix refcount leak in mips_cdmm_phys_base
+    - MIPS: RB532: fix return value of __setup handler
+    - MIPS: pgalloc: fix memory leak caused by pgd_free()
+    - mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
+    - power: ab8500_chargalg: Use CLOCK_MONOTONIC
+    - RDMA/irdma: Prevent some integer underflows
+    - Revert "RDMA/core: Fix ib_qp_usecnt_dec() called when error"
+    - RDMA/mlx5: Fix memory leak in error flow for subscribe event routine
+    - bpf, sockmap: Fix memleak in sk_psock_queue_msg
+    - bpf, sockmap: Fix memleak in tcp_bpf_sendmsg while sk msg is full
+    - bpf, sockmap: Fix more uncharged while msg has more_data
+    - bpf, sockmap: Fix double uncharge the mem of sk_msg
+    - samples/bpf, xdpsock: Fix race when running for fix duration of time
+    - USB: storage: ums-realtek: fix error code in rts51x_read_mem()
+    - drm/i915/display: Fix HPD short pulse handling for eDP
+    - netfilter: flowtable: Fix QinQ and pppoe support for inet table
+    - mt76: mt7921: fix mt7921_queues_acq implementation
+    - can: isotp: sanitize CAN ID checks in isotp_bind()
+    - can: isotp: return -EADDRNOTAVAIL when reading from unbound socket
+    - can: isotp: support MSG_TRUNC flag when reading from socket
+    - bareudp: use ipv6_mod_enabled to check if IPv6 enabled
+    - ibmvnic: fix race between xmit and reset
+    - af_unix: Fix some data-races around unix_sk(sk)->oob_skb.
+    - selftests/bpf: Fix error reporting from sock_fields programs
+    - Bluetooth: hci_uart: add missing NULL check in h5_enqueue
+    - Bluetooth: call hci_le_conn_failed with hdev lock in hci_le_conn_failed
+    - Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interrupt
+    - ipv4: Fix route lookups when handling ICMP redirects and PMTU updates
+    - af_netlink: Fix shift out of bounds in group mask calculation
+    - i2c: meson: Fix wrong speed use from probe
+    - netfilter: conntrack: Add and use nf_ct_set_auto_assign_helper_warned()
+    - i2c: mux: demux-pinctrl: do not deactivate a master that is not active
+    - powerpc/pseries: Fix use after free in remove_phb_dynamic()
+    - selftests/bpf/test_lirc_mode2.sh: Exit with proper code
+    - PCI: Avoid broken MSI on SB600 USB devices
+    - net: bcmgenet: Use stronger register read/writes to assure ordering
+    - tcp: ensure PMTU updates are processed during fastopen
+    - openvswitch: always update flow key after nat
+    - net: dsa: fix panic on shutdown if multi-chip tree failed to probe
+    - tipc: fix the timer expires after interval 100ms
+    - mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
+    - ice: fix 'scheduling while atomic' on aux critical err interrupt
+    - ice: don't allow to run ice_send_event_to_aux() in atomic ctx
+    - drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via
+      ethtool
+    - kernel/resource: fix kfree() of bootmem memory again
+    - staging: r8188eu: convert DBG_88E_LEVEL call in hal/rtl8188e_hal_init.c
+    - staging: r8188eu: release_firmware is not called if allocation fails
+    - mxser: fix xmit_buf leak in activate when LSR == 0xff
+    - fsi: scom: Fix error handling
+    - fsi: scom: Remove retries in indirect scoms
+    - pwm: lpc18xx-sct: Initialize driver data and hardware before pwmchip_add()
+    - pps: clients: gpio: Propagate return value from pps_gpio_probe
+    - fsi: Aspeed: Fix a potential double free
+    - misc: alcor_pci: Fix an error handling path
+    - cpufreq: qcom-cpufreq-nvmem: fix reading of PVS Valid fuse
+    - soundwire: intel: fix wrong register name in intel_shim_wake
+    - clk: qcom: ipq8074: fix PCI-E clock oops
+    - dmaengine: idxd: check GENCAP config support for gencfg register
+    - dmaengine: idxd: change bandwidth token to read buffers
+    - dmaengine: idxd: restore traffic class defaults after wq reset
+    - iio: mma8452: Fix probe failing when an i2c_device_id is used
+    - serial: 8250_aspeed_vuart: add PORT_ASPEED_VUART port type
+    - staging:iio:adc:ad7280a: Fix handing of device address bit reversing.
+    - pinctrl: renesas: r8a77470: Reduce size for narrow VIN1 channel
+    - pinctrl: renesas: checker: Fix miscalculation of number of states
+    - clk: qcom: ipq8074: Use floor ops for SDCC1 clock
+    - phy: dphy: Correct lpx parameter and its derivatives(ta_{get,go,sure})
+    - phy: phy-brcm-usb: fixup BCM4908 support
+    - serial: 8250_mid: Balance reference count for PCI DMA device
+    - serial: 8250_lpss: Balance reference count for PCI DMA device
+    - NFS: Use of mapping_set_error() results in spurious errors
+    - serial: 8250: Fix race condition in RTS-after-send handling
+    - iio: adc: Add check for devm_request_threaded_irq
+    - habanalabs: Add check for pci_enable_device
+    - NFS: Return valid errors from nfs2/3_decode_dirent()
+    - staging: r8188eu: fix endless loop in recv_func
+    - dma-debug: fix return value of __setup handlers
+    - clk: imx7d: Remove audio_mclk_root_clk
+    - clk: imx: off by one in imx_lpcg_parse_clks_from_dt()
+    - clk: at91: sama7g5: fix parents of PDMCs' GCLK
+    - clk: qcom: clk-rcg2: Update logic to calculate D value for RCG
+    - clk: qcom: clk-rcg2: Update the frac table for pixel clock
+    - dmaengine: hisi_dma: fix MSI allocate fail when reload hisi_dma
+    - remoteproc: qcom: Fix missing of_node_put in adsp_alloc_memory_region
+    - remoteproc: qcom_wcnss: Add missing of_node_put() in
+      wcnss_alloc_memory_region
+    - remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_region
+    - nvdimm/region: Fix default alignment for small regions
+    - clk: actions: Terminate clk_div_table with sentinel element
+    - clk: loongson1: Terminate clk_div_table with sentinel element
+    - clk: hisilicon: Terminate clk_div_table with sentinel element
+    - clk: clps711x: Terminate clk_div_table with sentinel element
+    - clk: Fix clk_hw_get_clk() when dev is NULL
+    - clk: tegra: tegra124-emc: Fix missing put_device() call in
+      emc_ensure_emc_driver
+    - mailbox: imx: fix crash in resume on i.mx8ulp
+    - NFS: remove unneeded check in decode_devicenotify_args()
+    - staging: mt7621-dts: fix LEDs and pinctrl on GB-PC1 devicetree
+    - staging: mt7621-dts: fix formatting
+    - staging: mt7621-dts: fix pinctrl properties for ethernet
+    - staging: mt7621-dts: fix GB-PC2 devicetree
+    - pinctrl: mediatek: Fix missing of_node_put() in mtk_pctrl_init
+    - pinctrl: mediatek: paris: Fix PIN_CONFIG_BIAS_* readback
+    - pinctrl: mediatek: paris: Fix "argument" argument type for mtk_pinconf_get()
+    - pinctrl: mediatek: paris: Fix pingroup pin config state readback
+    - pinctrl: mediatek: paris: Skip custom extra pin config dump for virtual
+      GPIOs
+    - pinctrl: microchip sgpio: use reset driver
+    - pinctrl: microchip-sgpio: lock RMW access
+    - pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
+    - pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
+    - tty: hvc: fix return value of __setup handler
+    - kgdboc: fix return value of __setup handler
+    - serial: 8250: fix XOFF/XON sending when DMA is used
+    - virt: acrn: obtain pa from VMA with PFNMAP flag
+    - virt: acrn: fix a memory leak in acrn_dev_ioctl()
+    - kgdbts: fix return value of __setup handler
+    - firmware: google: Properly state IOMEM dependency
+    - driver core: dd: fix return value of __setup handler
+    - jfs: fix divide error in dbNextAG
+    - netfilter: nf_conntrack_tcp: preserve liberal flag in tcp options
+    - SUNRPC don't resend a task on an offlined transport
+    - NFSv4.1: don't retry BIND_CONN_TO_SESSION on session error
+    - kdb: Fix the putarea helper function
+    - perf stat: Fix forked applications enablement of counters
+    - clk: qcom: gcc-msm8994: Fix gpll4 width
+    - vsock/virtio: initialize vdev->priv before using VQs
+    - vsock/virtio: read the negotiated features before using VQs
+    - vsock/virtio: enable VQs early on probe
+    - clk: Initialize orphan req_rate
+    - xen: fix is_xen_pmu()
+    - net: enetc: report software timestamping via SO_TIMESTAMPING
+    - net: hns3: fix bug when PF set the duplicate MAC address for VFs
+    - net: hns3: fix port base vlan add fail when concurrent with reset
+    - net: hns3: add vlan list lock to protect vlan list
+    - net: hns3: format the output of the MAC address
+    - net: hns3: refine the process when PF set VF VLAN
+    - net: phy: broadcom: Fix brcm_fet_config_init()
+    - selftests: test_vxlan_under_vrf: Fix broken test case
+    - NFS: Don't loop forever in nfs_do_recoalesce()
+    - net: hns3: clean residual vf config after disable sriov
+    - net: sparx5: depends on PTP_1588_CLOCK_OPTIONAL
+    - qlcnic: dcb: default to returning -EOPNOTSUPP
+    - net/x25: Fix null-ptr-deref caused by x25_disconnect
+    - net: sparx5: switchdev: fix possible NULL pointer dereference
+    - octeontx2-af: initialize action variable
+    - net: prefer nf_ct_put instead of nf_conntrack_put
+    - net/sched: act_ct: fix ref leak when switching zones
+    - NFSv4/pNFS: Fix another issue with a list iterator pointing to the head
+    - net: dsa: bcm_sf2_cfp: fix an incorrect NULL check on list iterator
+    - fs: fd tables have to be multiples of BITS_PER_LONG
+    - lib/test: use after free in register_test_dev_kmod()
+    - fs: fix fd table size alignment properly
+    - LSM: general protection fault in legacy_parse_param
+    - regulator: rpi-panel: Handle I2C errors/timing to the Atmel
+    - crypto: hisilicon/qm - cleanup warning in qm_vf_read_qos
+    - gcc-plugins/stackleak: Exactly match strings instead of prefixes
+    - pinctrl: npcm: Fix broken references to chip->parent_device
+    - rcu: Mark writes to the rcu_segcblist structure's ->flags field
+    - block/bfq_wf2q: correct weight to ioprio
+    - crypto: xts - Add softdep on ecb
+    - crypto: hisilicon/sec - not need to enable sm4 extra mode at HW V3
+    - block, bfq: don't move oom_bfqq
+    - selinux: use correct type for context length
+    - arm64: module: remove (NOLOAD) from linker script
+    - selinux: allow FIOCLEX and FIONCLEX with policy capability
+    - loop: use sysfs_emit() in the sysfs xxx show()
+    - Fix incorrect type in assignment of ipv6 port for audit
+    - irqchip/qcom-pdc: Fix broken locking
+    - irqchip/nvic: Release nvic_base upon failure
+    - fs/binfmt_elf: Fix AT_PHDR for unusual ELF files
+    - bfq: fix use-after-free in bfq_dispatch_request
+    - ACPICA: Avoid walking the ACPI Namespace if it is not there
+    - lib/raid6/test/Makefile: Use $(pound) instead of \# for Make 4.3
+    - Revert "Revert "block, bfq: honor already-setup queue merges""
+    - ACPI/APEI: Limit printable size of BERT table data
+    - PM: core: keep irq flags in device_pm_check_callbacks()
+    - parisc: Fix handling off probe non-access faults
+    - nvme-tcp: lockdep: annotate in-kernel sockets
+    - spi: tegra20: Use of_device_get_match_data()
+    - atomics: Fix atomic64_{read_acquire,set_release} fallbacks
+    - locking/lockdep: Iterate lock_classes directly when reading lockdep files
+    - ext4: correct cluster len and clusters changed accounting in ext4_mb_mark_bb
+    - ext4: fix ext4_mb_mark_bb() with flex_bg with fast_commit
+    - sched/tracing: Report TASK_RTLOCK_WAIT tasks as TASK_UNINTERRUPTIBLE
+    - ext4: don't BUG if someone dirty pages without asking ext4 first
+    - f2fs: fix to do sanity check on curseg->alloc_type
+    - NFSD: Fix nfsd_breaker_owns_lease() return values
+    - f2fs: don't get FREEZE lock in f2fs_evict_inode in frozen fs
+    - btrfs: harden identification of a stale device
+    - btrfs: make search_csum_tree return 0 if we get -EFBIG
+    - f2fs: use spin_lock to avoid hang
+    - f2fs: compress: fix to print raw data size in error path of lz4
+      decompression
+    - Adjust cifssb maximum read size
+    - ntfs: add sanity check on allocation size
+    - media: staging: media: zoran: move videodev alloc
+    - media: staging: media: zoran: calculate the right buffer number for
+      zoran_reap_stat_com
+    - media: staging: media: zoran: fix various V4L2 compliance errors
+    - media: atmel: atmel-isc-base: report frame sizes as full supported range
+    - media: ir_toy: free before error exiting
+    - ASoC: sh: rz-ssi: Make the data structures available before registering the
+      handlers
+    - ASoC: SOF: Intel: match sdw version on link_slaves_found
+    - media: imx-jpeg: Prevent decoding NV12M jpegs into single-planar buffers
+    - media: iommu/mediatek-v1: Free the existed fwspec if the master dev already
+      has
+    - media: iommu/mediatek: Return ENODEV if the device is NULL
+    - media: iommu/mediatek: Add device_link between the consumer and the larb
+      devices
+    - video: fbdev: nvidiafb: Use strscpy() to prevent buffer overflow
+    - video: fbdev: w100fb: Reset global state
+    - video: fbdev: cirrusfb: check pixclock to avoid divide by zero
+    - video: fbdev: omapfb: acx565akm: replace snprintf with sysfs_emit
+    - ARM: dts: qcom: fix gic_irq_domain_translate warnings for msm8960
+    - ARM: dts: bcm2837: Add the missing L1/L2 cache information
+    - ASoC: madera: Add dependencies on MFD
+    - media: atomisp_gmin_platform: Add DMI quirk to not turn AXP ELDO2 regulator
+      off on some boards
+    - media: atomisp: fix dummy_ptr check to avoid duplicate active_bo
+    - ARM: ftrace: avoid redundant loads or clobbering IP
+    - ARM: dts: imx7: Use audio_mclk_post_div instead audio_mclk_root_clk
+    - arm64: defconfig: build imx-sdma as a module
+    - video: fbdev: omapfb: panel-dsi-cm: Use sysfs_emit() instead of snprintf()
+    - video: fbdev: omapfb: panel-tpo-td043mtea1: Use sysfs_emit() instead of
+      snprintf()
+    - video: fbdev: udlfb: replace snprintf in show functions with sysfs_emit
+    - ARM: dts: bcm2711: Add the missing L1/L2 cache information
+    - ASoC: soc-core: skip zero num_dai component in searching dai name
+    - media: imx-jpeg: fix a bug of accessing array out of bounds
+    - media: cx88-mpeg: clear interrupt status register before streaming video
+    - uaccess: fix type mismatch warnings from access_ok()
+    - lib/test_lockup: fix kernel pointer check for separate address spaces
+    - ARM: tegra: tamonten: Fix I2C3 pad setting
+    - ARM: mmp: Fix failure to remove sram device
+    - ASoC: amd: vg: fix for pm resume callback sequence
+    - video: fbdev: sm712fb: Fix crash in smtcfb_write()
+    - media: i2c: ov5648: Fix lockdep error
+    - media: Revert "media: em28xx: add missing em28xx_close_extension"
+    - media: hdpvr: initialize dev->worker at hdpvr_register_videodev
+    - ASoC: Intel: sof_sdw: fix quirks for 2022 HP Spectre x360 13"
+    - tracing: Have TRACE_DEFINE_ENUM affect trace event types as well
+    - mmc: host: Return an error when ->enable_sdio_irq() ops is missing
+    - media: atomisp: fix bad usage at error handling logic
+    - ALSA: hda/realtek: Add alc256-samsung-headphone fixup
+    - KVM: x86: Reinitialize context if host userspace toggles EFER.LME
+    - KVM: x86/mmu: Move "invalid" check out of kvm_tdp_mmu_get_root()
+    - KVM: x86/mmu: Zap _all_ roots when unmapping gfn range in TDP MMU
+    - KVM: x86/mmu: Check for present SPTE when clearing dirty bit in TDP MMU
+    - KVM: x86: hyper-v: Drop redundant 'ex' parameter from kvm_hv_send_ipi()
+    - KVM: x86: hyper-v: Drop redundant 'ex' parameter from kvm_hv_flush_tlb()
+    - KVM: x86: hyper-v: Fix the maximum number of sparse banks for XMM fast TLB
+      flush hypercalls
+    - KVM: x86: hyper-v: HVCALL_SEND_IPI_EX is an XMM fast hypercall
+    - powerpc/kasan: Fix early region not updated correctly
+    - powerpc/lib/sstep: Fix 'sthcx' instruction
+    - powerpc/lib/sstep: Fix build errors with newer binutils
+    - powerpc: Add set_memory_{p/np}() and remove set_memory_attr()
+    - powerpc: Fix build errors with newer binutils
+    - drm/dp: Fix off-by-one in register cache size
+    - drm/i915: Treat SAGV block time 0 as SAGV disabled
+    - drm/i915: Fix PSF GV point mask when SAGV is not possible
+    - drm/i915: Reject unsupported TMDS rates on ICL+
+    - scsi: qla2xxx: Refactor asynchronous command initialization
+    - scsi: qla2xxx: Implement ref count for SRB
+    - scsi: qla2xxx: Fix stuck session in gpdb
+    - scsi: qla2xxx: Fix warning message due to adisc being flushed
+    - scsi: qla2xxx: Fix scheduling while atomic
+    - scsi: qla2xxx: Fix premature hw access after PCI error
+    - scsi: qla2xxx: Fix wrong FDMI data for 64G adapter
+    - scsi: qla2xxx: Fix warning for missing error code
+    - scsi: qla2xxx: Fix device reconnect in loop topology
+    - scsi: qla2xxx: edif: Fix clang warning
+    - scsi: qla2xxx: Fix T10 PI tag escape and IP guard options for 28XX adapters
+    - scsi: qla2xxx: Add devids and conditionals for 28xx
+    - scsi: qla2xxx: Check for firmware dump already collected
+    - scsi: qla2xxx: Suppress a kernel complaint in qla_create_qpair()
+    - scsi: qla2xxx: Fix disk failure to rediscover
+    - scsi: qla2xxx: Fix incorrect reporting of task management failure
+    - scsi: qla2xxx: Fix hang due to session stuck
+    - scsi: qla2xxx: Fix missed DMA unmap for NVMe ls requests
+    - scsi: qla2xxx: Fix N2N inconsistent PLOGI
+    - scsi: qla2xxx: Fix stuck session of PRLI reject
+    - scsi: qla2xxx: Reduce false trigger to login
+    - scsi: qla2xxx: Use correct feature type field during RFF_ID processing
+    - platform: chrome: Split trace include file
+    - KVM: x86: Check lapic_in_kernel() before attempting to set a SynIC irq
+    - KVM: x86: Avoid theoretical NULL pointer dereference in
+      kvm_irq_delivery_to_apic_fast()
+    - KVM: x86: Forbid VMM to set SYNIC/STIMER MSRs when SynIC wasn't activated
+    - KVM: Prevent module exit until all VMs are freed
+    - KVM: x86: fix sending PV IPI
+    - KVM: SVM: fix panic on out-of-bounds guest IRQ
+    - ubifs: rename_whiteout: Fix double free for whiteout_ui->data
+    - ubifs: Fix deadlock in concurrent rename whiteout and inode writeback
+    - ubifs: Add missing iput if do_tmpfile() failed in rename whiteout
+    - ubifs: Rename whiteout atomically
+    - ubifs: Fix 'ui->dirty' race between do_tmpfile() and writeback work
+    - ubifs: Rectify space amount budget for mkdir/tmpfile operations
+    - ubifs: setflags: Make dirtied_ino_d 8 bytes aligned
+    - ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock()
+    - ubifs: Fix to add refcount once page is set private
+    - ubifs: rename_whiteout: correct old_dir size computing
+    - nvme: allow duplicate NSIDs for private namespaces
+    - nvme: fix the read-only state for zoned namespaces with unsupposed features
+    - wireguard: queueing: use CFI-safe ptr_ring cleanup function
+    - wireguard: socket: free skb in send6 when ipv6 is disabled
+    - wireguard: socket: ignore v6 endpoints when ipv6 is disabled
+    - XArray: Fix xas_create_range() when multi-order entry present
+    - can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path
+    - can: mcba_usb: properly check endpoint type
+    - can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix return of error value
+    - XArray: Update the LRU list in xas_split()
+    - modpost: restore the warning message for missing symbol versions
+    - rtc: check if __rtc_read_time was successful
+    - gfs2: gfs2_setattr_size error path fix
+    - gfs2: Make sure FITRIM minlen is rounded up to fs block size
+    - net: hns3: fix the concurrency between functions reading debugfs
+    - net: hns3: fix software vlan talbe of vlan 0 inconsistent with hardware
+    - rxrpc: fix some null-ptr-deref bugs in server_key.c
+    - rxrpc: Fix call timer start racing with call destruction
+    - mailbox: imx: fix wakeup failure from freeze mode
+    - crypto: arm/aes-neonbs-cbc - Select generic cbc and aes
+    - watch_queue: Free the page array when watch_queue is dismantled
+    - pinctrl: pinconf-generic: Print arguments for bias-pull-*
+    - watchdog: rti-wdt: Add missing pm_runtime_disable() in probe function
+    - net: sparx5: uses, depends on BRIDGE or !BRIDGE
+    - pinctrl: nuvoton: npcm7xx: Rename DS() macro to DSTR()
+    - pinctrl: nuvoton: npcm7xx: Use %zu printk format for ARRAY_SIZE()
+    - ASoC: mediatek: mt6358: add missing EXPORT_SYMBOLs
+    - ubi: Fix race condition between ctrl_cdev_ioctl and ubi_cdev_ioctl
+    - ARM: iop32x: offset IRQ numbers by 1
+    - block: Fix the maximum minor value is blk_alloc_ext_minor()
+    - io_uring: fix memory leak of uid in files registration
+    - riscv module: remove (NOLOAD)
+    - ACPI: CPPC: Avoid out of bounds access when parsing _CPC data
+    - vhost: handle error while adding split ranges to iotlb
+    - spi: Fix Tegra QSPI example
+    - platform/chrome: cros_ec_typec: Check for EC device
+    - can: isotp: restore accidentally removed MSG_PEEK feature
+    - proc: bootconfig: Add null pointer check
+    - drm/connector: Fix typo in documentation
+    - scsi: qla2xxx: Add qla2x00_async_done() for async routines
+    - staging: mt7621-dts: fix pinctrl-0 items to be size-1 items on ethernet
+    - arm64: mm: Drop 'const' from conditional arm64_dma_phys_limit definition
+    - ASoC: soc-compress: Change the check for codec_dai
+    - Reinstate some of "swiotlb: rework "fix info leak with DMA_FROM_DEVICE""
+    - tracing: Have type enum modifications copy the strings
+    - net: add skb_set_end_offset() helper
+    - net: preserve skb_end_offset() in skb_unclone_keeptruesize()
+    - mm/mmap: return 1 from stack_guard_gap __setup() handler
+    - ARM: 9187/1: JIVE: fix return value of __setup handler
+    - mm/memcontrol: return 1 from cgroup.memory __setup() handler
+    - mm/usercopy: return 1 from hardened_usercopy __setup() handler
+    - af_unix: Support POLLPRI for OOB.
+    - bpf: Adjust BPF stack helper functions to accommodate skip > 0
+    - bpf: Fix comment for helper bpf_current_task_under_cgroup()
+    - mmc: rtsx: Use pm_runtime_{get,put}() to handle runtime PM
+    - dt-bindings: mtd: nand-controller: Fix the reg property description
+    - dt-bindings: mtd: nand-controller: Fix a comment in the examples
+    - dt-bindings: spi: mxic: The interrupt property is not mandatory
+    - dt-bindings: memory: mtk-smi: No need mediatek,larb-id for mt8167
+    - dt-bindings: pinctrl: pinctrl-microchip-sgpio: Fix example
+    - ubi: fastmap: Return error code if memory allocation fails in add_aeb()
+    - ASoC: SOF: Intel: Fix build error without SND_SOC_SOF_PCI_DEV
+    - ASoC: topology: Allow TLV control to be either read or write
+    - perf vendor events: Update metrics for SkyLake Server
+    - media: ov6650: Add try support to selection API operations
+    - media: ov6650: Fix crop rectangle affected by set format
+    - spi: mediatek: support tick_delay without enhance_timing
+    - ARM: dts: spear1340: Update serial node properties
+    - ARM: dts: spear13xx: Update SPI dma properties
+    - arm64: dts: ls1043a: Update i2c dma properties
+    - arm64: dts: ls1046a: Update i2c node dma properties
+    - um: Fix uml_mconsole stop/go
+    - docs: sysctl/kernel: add missing bit to panic_print
+    - openvswitch: Fixed nd target mask field in the flow dump.
+    - torture: Make torture.sh help message match reality
+    - n64cart: convert bi_disk to bi_bdev->bd_disk fix build
+    - mmc: rtsx: Let MMC core handle runtime PM
+    - mmc: rtsx: Fix build errors/warnings for unused variable
+    - KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
+    - iommu/dma: Skip extra sync during unmap w/swiotlb
+    - iommu/dma: Fold _swiotlb helpers into callers
+    - iommu/dma: Check CONFIG_SWIOTLB more broadly
+    - swiotlb: Support aligned swiotlb buffers
+    - iommu/dma: Account for min_align_mask w/swiotlb
+    - coredump: Snapshot the vmas in do_coredump
+    - coredump: Remove the WARN_ON in dump_vma_snapshot
+    - coredump/elf: Pass coredump_params into fill_note_info
+    - coredump: Use the vma snapshot in fill_files_note
+    - PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
+    - Linux 5.15.33
+  * Jammy update: v5.15.32 upstream stable release (LP: #1969106)
+    - net: ipv6: fix skb_over_panic in __ip6_append_data
+    - tpm: Fix error handling in async work
+    - Bluetooth: btusb: Add another Realtek 8761BU
+    - llc: fix netdevice reference leaks in llc_ui_bind()
+    - ASoC: sti: Fix deadlock via snd_pcm_stop_xrun() call
+    - ALSA: oss: Fix PCM OSS buffer allocation overflow
+    - ALSA: usb-audio: add mapping for new Corsair Virtuoso SE
+    - ALSA: hda/realtek: Add quirk for Clevo NP70PNJ
+    - ALSA: hda/realtek: Add quirk for Clevo NP50PNJ
+    - ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
+    - ALSA: hda/realtek: Add quirk for ASUS GA402
+    - ALSA: pcm: Fix races among concurrent hw_params and hw_free calls
+    - ALSA: pcm: Fix races among concurrent read/write and buffer changes
+    - ALSA: pcm: Fix races among concurrent prepare and hw_params/hw_free calls
+    - ALSA: pcm: Fix races among concurrent prealloc proc writes
+    - ALSA: pcm: Add stream lock during PCM reset ioctl operations
+    - ALSA: usb-audio: Add mute TLV for playback volumes on RODE NT-USB
+    - ALSA: cmipci: Restore aux vol on suspend/resume
+    - ALSA: pci: fix reading of swapped values from pcmreg in AC97 codec
+    - drivers: net: xgene: Fix regression in CRC stripping
+    - ACPI / x86: Work around broken XSDT on Advantech DAC-BJ01 board
+    - ACPI: battery: Add device HID and quirk for Microsoft Surface Go 3
+    - ACPI: video: Force backlight native for Clevo NL5xRU and NL5xNU
+    - crypto: qat - disable registration of algorithms
+    - Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
+    - Revert "ath: add support for special 0x0 regulatory domain"
+    - drm/virtio: Ensure that objs is not NULL in virtio_gpu_array_put_free()
+    - rcu: Don't deboost before reporting expedited quiescent state
+    - uaccess: fix integer overflow on access_ok()
+    - mac80211: fix potential double free on mesh join
+    - tpm: use try_get_ops() in tpm-space.c
+    - wcn36xx: Differentiate wcn3660 from wcn3620
+    - m68k: fix access_ok for coldfire
+    - nds32: fix access_ok() checks in get/put_user
+    - llc: only change llc->dev when bind() succeeds
+    - Linux 5.15.32
+  * Jammy update: v5.15.31 upstream stable release (LP: #1969105)
+    - crypto: qcom-rng - ensure buffer for generate is completely filled
+    - ocfs2: fix crash when initialize filecheck kobj fails
+    - mm: swap: get rid of livelock in swapin readahead
+    - block: release rq qos structures for queue without disk
+    - drm/mgag200: Fix PLL setup for g200wb and g200ew
+    - efi: fix return value of __setup handlers
+    - alx: acquire mutex for alx_reinit in alx_change_mtu
+    - vsock: each transport cycles only on its own sockets
+    - esp6: fix check on ipv6_skip_exthdr's return value
+    - net: phy: marvell: Fix invalid comparison in the resume and suspend
+      functions
+    - net/packet: fix slab-out-of-bounds access in packet_recvmsg()
+    - atm: eni: Add check for dma_map_single
+    - iavf: Fix double free in iavf_reset_task
+    - hv_netvsc: Add check for kvmalloc_array
+    - drm/imx: parallel-display: Remove bus flags check in
+      imx_pd_bridge_atomic_check()
+    - drm/panel: simple: Fix Innolux G070Y2-L01 BPP settings
+    - net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
+    - drm: Don't make DRM_PANEL_BRIDGE dependent on DRM_KMS_HELPERS
+    - net: dsa: Add missing of_node_put() in dsa_port_parse_of
+    - net: phy: mscc: Add MODULE_FIRMWARE macros
+    - bnx2x: fix built-in kernel driver load failure
+    - net: bcmgenet: skip invalid partial checksums
+    - net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower
+      offload
+    - iavf: Fix hang during reboot/shutdown
+    - arm64: fix clang warning about TRAMP_VALIAS
+    - usb: gadget: rndis: prevent integer overflow in rndis_set_response()
+    - usb: gadget: Fix use-after-free bug by not setting udc->dev.driver
+    - usb: usbtmc: Fix bug in pipe direction for control transfers
+    - scsi: mpt3sas: Page fault in reply q processing
+    - Input: aiptek - properly check endpoint type
+    - perf symbols: Fix symbol size calculation condition
+    - btrfs: skip reserved bytes warning on unmount after log cleanup failure
+    - Linux 5.15.31
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Fri, 29 Jul 2022 09:57:21 +1000
+
+linux-xilinx-zynqmp (5.15.0-1011.12) jammy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Enable imx219 kernel module
+
+  * Miscellaneous upstream changes
+    - xilinx: Enable imx219 for SOM rpi apps
+    - drm: xlnx: zynqmp_dp: Fix kernel dump messages when the DP cable is
+      disconnected
+    - staging: xilinx-tsn: initialize timer_priv struct in axienet_local
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Thu, 16 Jun 2022 09:20:28 +1000
+
+linux-xilinx-zynqmp (5.15.0-1010.11) jammy; urgency=medium
+
+  * Miscellaneous upstream changes
+    - net: macb: Use device_link framework to specify suspend/resume dependency
+    - arm64: zynqmp: Add linux,code for fwuen button
+    - usb: dwc3: xilinx: Fix error handling when getting USB3 PHY
+    - usb: dwc3: Added remote wake-up in xilinx glue driver
+    - usb: xhci-plat: Add remote wakeup support for xilinx
+    - usb: dwc3: xilinx: fix usb3 non-wakeup source resume failure
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Tue, 07 Jun 2022 20:36:56 +0800
+
+linux-xilinx-zynqmp (5.15.0-1009.10) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+
+  * INVALID or PRIVATE BUG (LP: #1975694)
+    - Enable Xilinx mv-camera-10gige-module kernel module
+    - [Config] Enable xilinx-mv-camera-10gige-module
+
+  * INVALID or PRIVATE BUG (LP: #1975695)
+    - Enable Xilinx mv-camera-sensor-module kernel module
+
+  [ Ubuntu: 5.15.0-33.34 ]
+
+  * jammy/linux: 5.15.0-33.34 -proposed tracker (LP: #1973924)
+  * CVE-2022-29581
+    - net/sched: cls_u32: fix netns refcount changes in u32_change()
+  * ext4: limit length to bitmap_maxbytes (LP: #1972281)
+    - ext4: limit length to bitmap_maxbytes - blocksize in punch_hole
+  * Unprivileged users may use PTRACE_SEIZE to set PTRACE_O_SUSPEND_SECCOMP
+    option (LP: #1972740)
+    - ptrace: Check PTRACE_O_SUSPEND_SECCOMP permission on PTRACE_SEIZE
+
+  [ Ubuntu: 5.15.0-30.31 ]
+
+  * jammy/linux: 5.15.0-30.31 -proposed tracker (LP: #1971685)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - debian/dkms-versions -- update from kernel-versions (main/2022.04.18)
+  * Intel: enable x86 AMX (LP: #1967750)
+    - x86/extable: Tidy up redundant handler functions
+    - x86/extable: Get rid of redundant macros
+    - x86/mce: Deduplicate exception handling
+    - x86/mce: Get rid of stray semicolons
+    - x86/extable: Rework the exception table mechanics
+    - x86/extable: Provide EX_TYPE_DEFAULT_MCE_SAFE and EX_TYPE_FAULT_MCE_SAFE
+    - x86/copy_mc: Use EX_TYPE_DEFAULT_MCE_SAFE for exception fixups
+    - x86/fpu: Use EX_TYPE_FAULT_MCE_SAFE for exception fixups
+    - x86/extable: Remove EX_TYPE_FAULT from MCE safe fixups
+    - x86/fpu/signal: Clarify exception handling in restore_fpregs_from_user()
+    - x86/fpu/signal: Move header zeroing out of xsave_to_user_sigframe()
+    - x86/fpu/signal: Move xstate clearing out of copy_fpregs_to_sigframe()
+    - x86/fpu/signal: Change return type of copy_fpstate_to_sigframe() to boolean
+    - x86/fpu/signal: Change return type of copy_fpregs_to_sigframe() helpers to
+      boolean
+    - x86/signal: Change return type of restore_sigcontext() to boolean
+    - x86/fpu/signal: Change return type of fpu__restore_sig() to boolean
+    - x86/fpu/signal: Change return type of __fpu_restore_sig() to boolean
+    - x86/fpu/signal: Change return code of check_xstate_in_sigframe() to boolean
+    - x86/fpu/signal: Change return code of restore_fpregs_from_user() to boolean
+    - x86/fpu/signal: Fix missed conversion to correct boolean retval in
+      save_xstate_epilog()
+    - x86/fpu: Remove pointless argument from switch_fpu_finish()
+    - x86/fpu: Update stale comments
+    - x86/pkru: Remove useless include
+    - x86/fpu: Restrict xsaves()/xrstors() to independent states
+    - x86/fpu: Cleanup the on_boot_cpu clutter
+    - x86/fpu: Remove pointless memset in fpu_clone()
+    - x86/process: Clone FPU in copy_thread()
+    - x86/fpu: Do not inherit FPU context for kernel and IO worker threads
+    - x86/fpu: Cleanup xstate xcomp_bv initialization
+    - x86/fpu/xstate: Provide and use for_each_xfeature()
+    - x86/fpu/xstate: Mark all init only functions __init
+    - x86/fpu: Move KVMs FPU swapping to FPU core
+    - x86/fpu: Replace KVMs home brewed FPU copy from user
+    - x86/fpu: Rework copy_xstate_to_uabi_buf()
+    - x86/fpu: Mark fpu__init_prepare_fx_sw_frame() as __init
+    - x86/fpu: Move context switch and exit to user inlines into sched.h
+    - x86/fpu: Clean up CPU feature tests
+    - x86/fpu: Make os_xrstor_booting() private
+    - x86/fpu: Move os_xsave() and os_xrstor() to core
+    - x86/fpu: Move legacy ASM wrappers to core
+    - x86/fpu: Make WARN_ON_FPU() private
+    - x86/fpu: Move fpregs_restore_userregs() to core
+    - x86/fpu: Move mxcsr related code to core
+    - x86/fpu: Move fpstate functions to api.h
+    - x86/fpu: Remove internal.h dependency from fpu/signal.h
+    - x86/sev: Include fpu/xcr.h
+    - x86/fpu: Mop up the internal.h leftovers
+    - x86/fpu: Replace the includes of fpu/internal.h
+    - x86/fpu: Provide a proper function for ex_handler_fprestore()
+    - x86/fpu: Replace KVMs home brewed FPU copy to user
+    - x86/fpu: Provide struct fpstate
+    - x86/fpu: Convert fpstate_init() to struct fpstate
+    - x86/fpu: Convert restore_fpregs_from_fpstate() to struct fpstate
+    - x86/fpu: Replace KVMs xstate component clearing
+    - x86/KVM: Convert to fpstate
+    - x86/fpu: Convert tracing to fpstate
+    - x86/fpu/regset: Convert to fpstate
+    - x86/fpu/signal: Convert to fpstate
+    - x86/fpu/core: Convert to fpstate
+    - x86/math-emu: Convert to fpstate
+    - x86/fpu: Remove fpu::state
+    - x86/fpu: Do not leak fpstate pointer on fork
+    - x86/process: Move arch_thread_struct_whitelist() out of line
+    - x86/fpu: Add size and mask information to fpstate
+    - x86/fpu: Use fpstate::size
+    - x86/fpu/xstate: Use fpstate for os_xsave()
+    - x86/fpu/xstate: Use fpstate for xsave_to_user_sigframe()
+    - x86/fpu: Use fpstate in fpu_copy_kvm_uabi_to_fpstate()
+    - x86/fpu: Use fpstate in __copy_xstate_to_uabi_buf()
+    - x86/fpu/xstate: Use fpstate for copy_uabi_to_xstate()
+    - x86/fpu/signal: Use fpstate for size and features
+    - x86/fpu: Provide struct fpu_config
+    - x86/fpu: Cleanup fpu__init_system_xstate_size_legacy()
+    - x86/fpu/xstate: Cleanup size calculations
+    - x86/fpu: Move xstate size to fpu_*_cfg
+    - x86/fpu: Move xstate feature masks to fpu_*_cfg
+    - x86/fpu: Mop up xfeatures_mask_uabi()
+    - x86/fpu: Rework restore_regs_from_fpstate()
+    - x86/fpu/xstate: Move remaining xfeature helpers to core
+    - x86/fpu: Prepare for sanitizing KVM FPU code
+    - x86/fpu: Provide infrastructure for KVM FPU cleanup
+    - x86/kvm: Convert FPU handling to a single swap buffer
+    - x86/fpu: Remove old KVM FPU interface
+    - signal: Add an optional check for altstack size
+    - x86/signal: Implement sigaltstack size validation
+    - x86/fpu/xstate: Provide xstate_calculate_size()
+    - x86/fpu: Add members to struct fpu to cache permission information
+    - x86/fpu: Add fpu_state_config::legacy_features
+    - x86/arch_prctl: Add controls for dynamic XSTATE components
+    - x86/fpu: Add basic helpers for dynamically enabled features
+    - x86/signal: Use fpu::__state_user_size for sigalt stack validation
+    - x86/fpu/signal: Prepare for variable sigframe length
+    - x86/fpu: Prepare fpu_clone() for dynamically enabled features
+    - x86/fpu: Reset permission and fpstate on exec()
+    - x86/cpufeatures: Add eXtended Feature Disabling (XFD) feature bit
+    - x86/msr-index: Add MSRs for XFD
+    - x86/fpu: Add XFD state to fpstate
+    - x86/fpu: Add sanity checks for XFD
+    - x86/fpu: Update XFD state where required
+    - x86/fpu/xstate: Add XFD #NM handler
+    - x86/fpu/xstate: Add fpstate_realloc()/free()
+    - x86/fpu/xstate: Prepare XSAVE feature table for gaps in state component
+      numbers
+    - x86/fpu/amx: Define AMX state components and have it used for boot-time
+      checks
+    - x86/fpu: Calculate the default sizes independently
+    - x86/fpu: Add XFD handling for dynamic states
+    - x86/fpu/amx: Enable the AMX feature in 64-bit mode
+    - selftests/x86/amx: Add test cases for AMX state management
+    - selftests/x86/amx: Add context switch test
+    - Documentation/x86: Add documentation for using dynamic XSTATE features
+    - x86/fpu/signal: Initialize sw_bytes in save_xstate_epilog()
+    - signal: Skip the altstack update when not needed
+    - x86/cpufeatures: Put the AMX macros in the word 18 block
+    - x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
+    - selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
+    - [Config] updateconfigs after AMX patchset
+
+ -- Portia Stephens <portia.stephens@canonical.com>  Mon, 06 Jun 2022 11:41:00 +1000
+
+linux-xilinx-zynqmp (5.15.0-1008.9) jammy; urgency=medium
+
+  * Miscellaneous upstream changes
+    - mtd: spi-nor: For erase size equal to 0 set erase size_shift to 0
+    - xilinx-ams: Fix UBSan Warning
+    - net: macb: Fix ethtool WOL helper
+    - dt-bindings: fpga: Add property "resets" to xilinx-afi driver
+    - fpga: Add ps-pl reset handling through xilinx afi driver
+    - staging: xilinx-tsn: Fix axienet_tsn ioctl
+    - staging: xilinx-tsn: Add ethtool hook to read phc associated with ep
+    - staging: xilinx-tsn: Remove hardcoded interface names
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Thu, 26 May 2022 21:43:48 +0800
+
+linux-xilinx-zynqmp (5.15.0-1007.8) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1966941) // INVALID or PRIVATE BUG
+    (LP: #1968270)
+    - [Config] Disable CONFIG_UBSAN
+
+  * INVALID or PRIVATE BUG (LP: #1970466)
+    - [Config] Enable fancontrol
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Sat, 07 May 2022 19:26:24 +0800
+
+linux-xilinx-zynqmp (5.15.0-1006.7) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1967068)
+    - arm64: dts: zynqmp: Add is-dual for qspi
+    - [Config] Disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
+
+  * INVALID or PRIVATE BUG (LP: #1968978)
+    - [Config] Update configs for TSN
+
+  * Miscellaneous upstream changes
+    - Import Xilinx VCU kernel modules
+    - Enable VCU kernel modules as default
+    - Disable CONFIG_VIDEO_ALLEGRO_DVT
+    - Enable Xilinx HDMI kernel modules
+    - Fix build error for HDMI kernel modules
+    - Import XRT 2022.1 kernel modules
+    - Add DRM_ZOCL option for XRT driver
+
+  [ Ubuntu: 5.15.0-27.28 ]
+
+  * jammy/linux: 5.15.0-27.28 -proposed tracker (LP: #1968954)
+
+  [ Ubuntu: 5.15.0-26.27 ]
+
+  * jammy/linux: 5.15.0-26.27 -proposed tracker (LP: #1968850)
+  * CVE-2022-1016
+    - netfilter: nf_tables: initialize registers in nft_do_chain()
+  * CVE-2022-1015
+    - netfilter: nf_tables: validate registers coming from userspace.
+  * CVE-2022-26490
+    - nfc: st21nfca: Fix potential buffer overflows in EVT_TRANSACTION
+  * harden indirect calls against BHI attacks (LP: #1967579)
+    - objtool: Classify symbols
+    - objtool: Explicitly avoid self modifying code in .altinstr_replacement
+    - objtool: Shrink struct instruction
+    - objtool,x86: Replace alternatives with .retpoline_sites
+    - x86/retpoline: Remove unused replacement symbols
+    - x86/asm: Fix register order
+    - x86/asm: Fixup odd GEN-for-each-reg.h usage
+    - x86/retpoline: Move the retpoline thunk declarations to nospec-branch.h
+    - x86/retpoline: Create a retpoline thunk array
+    - x86/alternative: Implement .retpoline_sites support
+    - x86/alternative: Handle Jcc __x86_indirect_thunk_\reg
+    - x86/alternative: Try inline spectre_v2=retpoline,amd
+    - x86/alternative: Add debug prints to apply_retpolines()
+    - bpf,x86: Simplify computing label offsets
+    - bpf,x86: Respect X86_FEATURE_RETPOLINE*
+
+  [ Ubuntu: 5.15.0-25.25 ]
+
+  * jammy/linux: 5.15.0-25.25 -proposed tracker (LP: #1967146)
+  * Miscellaneous Ubuntu changes
+    - SAUCE: Revert "scsi: core: Reallocate device's budget map on queue depth
+      change"
+
+  [ Ubuntu: 5.15.0-24.24 ]
+
+  * jammy/linux: 5.15.0-24.24 -proposed tracker (LP: #1966305)
+  * Update OS policy capability handshake (LP: #1966089)
+    - thermal: int340x: Update OS policy capability handshake
+  * Jammy update: v5.15.30 upstream stable release (LP: #1966057)
+    - Revert "xfrm: state and policy should fail if XFRMA_IF_ID 0"
+    - arm64: dts: rockchip: fix rk3399-puma-haikou USB OTG mode
+    - xfrm: Check if_id in xfrm_migrate
+    - xfrm: Fix xfrm migrate issues when address family changes
+    - arm64: dts: rockchip: fix rk3399-puma eMMC HS400 signal integrity
+    - arm64: dts: rockchip: align pl330 node name with dtschema
+    - arm64: dts: rockchip: reorder rk3399 hdmi clocks
+    - arm64: dts: agilex: use the compatible "intel,socfpga-agilex-hsotg"
+    - ARM: dts: rockchip: reorder rk322x hmdi clocks
+    - ARM: dts: rockchip: fix a typo on rk3288 crypto-controller
+    - mac80211: refuse aggregations sessions before authorized
+    - MIPS: smp: fill in sibling and core maps earlier
+    - ARM: 9178/1: fix unmet dependency on BITREVERSE for HAVE_ARCH_BITREVERSE
+    - Bluetooth: hci_core: Fix leaking sent_cmd skb
+    - can: rcar_canfd: rcar_canfd_channel_probe(): register the CAN device when
+      fully ready
+    - atm: firestream: check the return value of ioremap() in fs_init()
+    - iwlwifi: don't advertise TWT support
+    - drm/vrr: Set VRR capable prop only if it is attached to connector
+    - nl80211: Update bss channel on channel switch for P2P_CLIENT
+    - tcp: make tcp_read_sock() more robust
+    - sfc: extend the locking on mcdi->seqno
+    - bnx2: Fix an error message
+    - kselftest/vm: fix tests build with old libc
+    - x86/module: Fix the paravirt vs alternative order
+    - ice: Fix race condition during interface enslave
+    - Linux 5.15.30
+  * Jammy update: v5.15.29 upstream stable release (LP: #1966056)
+    - arm64: dts: qcom: sm8350: Describe GCC dependency clocks
+    - arm64: dts: qcom: sm8350: Correct UFS symbol clocks
+    - HID: elo: Revert USB reference counting
+    - HID: hid-thrustmaster: fix OOB read in thrustmaster_interrupts
+    - ARM: boot: dts: bcm2711: Fix HVS register range
+    - clk: qcom: gdsc: Add support to update GDSC transition delay
+    - clk: qcom: dispcc: Update the transition delay for MDSS GDSC
+    - HID: vivaldi: fix sysfs attributes leak
+    - arm64: dts: armada-3720-turris-mox: Add missing ethernet0 alias
+    - tipc: fix kernel panic when enabling bearer
+    - vdpa/mlx5: add validation for VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET command
+    - vduse: Fix returning wrong type in vduse_domain_alloc_iova()
+    - net: phy: meson-gxl: fix interrupt handling in forced mode
+    - mISDN: Fix memory leak in dsp_pipeline_build()
+    - vhost: fix hung thread due to erroneous iotlb entries
+    - virtio-blk: Don't use MAX_DISCARD_SEGMENTS if max_discard_seg is zero
+    - vdpa: fix use-after-free on vp_vdpa_remove
+    - isdn: hfcpci: check the return value of dma_set_mask() in setup_hw()
+    - net: qlogic: check the return value of dma_alloc_coherent() in
+      qed_vf_hw_prepare()
+    - esp: Fix possible buffer overflow in ESP transformation
+    - esp: Fix BEET mode inter address family tunneling on GSO
+    - qed: return status of qed_iov_get_link
+    - smsc95xx: Ignore -ENODEV errors when device is unplugged
+    - gpiolib: acpi: Convert ACPI value of debounce to microseconds
+    - drm/sun4i: mixer: Fix P010 and P210 format numbers
+    - net: dsa: mt7530: fix incorrect test in mt753x_phylink_validate()
+    - ARM: dts: aspeed: Fix AST2600 quad spi group
+    - iavf: Fix handling of vlan strip virtual channel messages
+    - i40e: stop disabling VFs due to PF error responses
+    - ice: stop disabling VFs due to PF error responses
+    - ice: Fix error with handling of bonding MTU
+    - ice: Don't use GFP_KERNEL in atomic context
+    - ice: Fix curr_link_speed advertised speed
+    - ethernet: Fix error handling in xemaclite_of_probe
+    - tipc: fix incorrect order of state message data sanity check
+    - net: ethernet: ti: cpts: Handle error for clk_enable
+    - net: ethernet: lpc_eth: Handle error for clk_enable
+    - net: marvell: prestera: Add missing of_node_put() in
+      prestera_switch_set_base_mac_addr
+    - ax25: Fix NULL pointer dereference in ax25_kill_by_device
+    - net/mlx5: Fix size field in bufferx_reg struct
+    - net/mlx5: Fix a race on command flush flow
+    - net/mlx5e: Lag, Only handle events from highest priority multipath entry
+    - NFC: port100: fix use-after-free in port100_send_complete
+    - selftests: pmtu.sh: Kill tcpdump processes launched by subshell.
+    - selftests: pmtu.sh: Kill nettest processes launched in subshell.
+    - gpio: ts4900: Do not set DAT and OE together
+    - gianfar: ethtool: Fix refcount leak in gfar_get_ts_info
+    - net: phy: DP83822: clear MISR2 register to disable interrupts
+    - sctp: fix kernel-infoleak for SCTP sockets
+    - net: bcmgenet: Don't claim WOL when its not available
+    - net: phy: meson-gxl: improve link-up behavior
+    - selftests/bpf: Add test for bpf_timer overwriting crash
+    - swiotlb: fix info leak with DMA_FROM_DEVICE
+    - usb: dwc3: pci: add support for the Intel Raptor Lake-S
+    - pinctrl: tigerlake: Revert "Add Alder Lake-M ACPI ID"
+    - KVM: Fix lockdep false negative during host resume
+    - kvm: x86: Disable KVM_HC_CLOCK_PAIRING if tsc is in always catchup mode
+    - spi: rockchip: Fix error in getting num-cs property
+    - spi: rockchip: terminate dma transmission when slave abort
+    - drm/vc4: hdmi: Unregister codec device on unbind
+    - x86/kvm: Don't use pv tlb/ipi/sched_yield if on 1 vCPU
+    - net-sysfs: add check for netdevice being present to speed_show
+    - hwmon: (pmbus) Clear pmbus fault/warning bits after read
+    - PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
+    - gpio: Return EPROBE_DEFER if gc->to_irq is NULL
+    - drm/amdgpu: bypass tiling flag check in virtual display case (v2)
+    - Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
+    - Revert "xen-netback: Check for hotplug-status existence before watching"
+    - ipv6: prevent a possible race condition with lifetimes
+    - tracing: Ensure trace buffer is at least 4096 bytes large
+    - tracing/osnoise: Make osnoise_main to sleep for microseconds
+    - selftest/vm: fix map_fixed_noreplace test failure
+    - selftests/memfd: clean up mapping in mfd_fail_write
+    - ARM: Spectre-BHB: provide empty stub for non-config
+    - fuse: fix fileattr op failure
+    - fuse: fix pipe buffer lifetime for direct_io
+    - staging: rtl8723bs: Fix access-point mode deadlock
+    - staging: gdm724x: fix use after free in gdm_lte_rx()
+    - net: macb: Fix lost RX packet wakeup race in NAPI receive
+    - riscv: alternative only works on !XIP_KERNEL
+    - mmc: meson: Fix usage of meson_mmc_post_req()
+    - riscv: Fix auipc+jalr relocation range checks
+    - tracing/osnoise: Force quiescent states while tracing
+    - arm64: dts: marvell: armada-37xx: Remap IO space to bus address 0x0
+    - arm64: Ensure execute-only permissions are not allowed without EPAN
+    - arm64: kasan: fix include error in MTE functions
+    - swiotlb: rework "fix info leak with DMA_FROM_DEVICE"
+    - KVM: x86/mmu: kvm_faultin_pfn has to return false if pfh is returned
+    - virtio: unexport virtio_finalize_features
+    - virtio: acknowledge all features before access
+    - net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
+    - ARM: fix Thumb2 regression with Spectre BHB
+    - watch_queue: Fix filter limit check
+    - watch_queue, pipe: Free watchqueue state after clearing pipe ring
+    - watch_queue: Fix to release page in ->release()
+    - watch_queue: Fix to always request a pow-of-2 pipe ring size
+    - watch_queue: Fix the alloc bitmap size to reflect notes allocated
+    - watch_queue: Free the alloc bitmap when the watch_queue is torn down
+    - watch_queue: Fix lack of barrier/sync/lock between post and read
+    - watch_queue: Make comment about setting ->defunct more accurate
+    - x86/boot: Fix memremap of setup_indirect structures
+    - x86/boot: Add setup_indirect support in early_memremap_is_setup_data()
+    - x86/sgx: Free backing memory after faulting the enclave page
+    - x86/traps: Mark do_int3() NOKPROBE_SYMBOL
+    - drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP
+    - btrfs: make send work with concurrent block group relocation
+    - drm/i915: Workaround broken BIOS DBUF configuration on TGL/RKL
+    - riscv: dts: k210: fix broken IRQs on hart1
+    - block: drop unused includes in <linux/genhd.h>
+    - Revert "net: dsa: mv88e6xxx: flush switchdev FDB workqueue before removing
+      VLAN"
+    - vhost: allow batching hint without size
+    - Linux 5.15.29
+  * Jammy update: v5.15.28 upstream stable release (LP: #1966055)
+    - slip: fix macro redefine warning
+    - ARM: fix co-processor register typo
+    - ARM: Do not use NOCROSSREFS directive with ld.lld
+    - arm64: Do not include __READ_ONCE() block in assembly files
+    - ARM: fix build warning in proc-v7-bugs.c
+    - xen/xenbus: don't let xenbus_grant_ring() remove grants in error case
+    - xen/grant-table: add gnttab_try_end_foreign_access()
+    - xen/blkfront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/netfront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/scsifront: don't use gnttab_query_foreign_access() for mapped status
+    - xen/gntalloc: don't use gnttab_query_foreign_access()
+    - xen: remove gnttab_query_foreign_access()
+    - xen/9p: use alloc/free_pages_exact()
+    - xen/pvcalls: use alloc/free_pages_exact()
+    - xen/gnttab: fix gnttab_end_foreign_access() without page specified
+    - xen/netfront: react properly to failing gnttab_end_foreign_access_ref()
+    - Revert "ACPI: PM: s2idle: Cancel wakeup before dispatching EC GPE"
+    - Linux 5.15.28
+  * zfcpdump-kernel update to v5.15 (LP: #1965766)
+    - SAUCE: Audit: Fix incorrect static inline function declration.
+  * [22.04 FEAT] SMC-R v2 Support (LP: #1929035)
+    - net/smc: save stack space and allocate smc_init_info
+    - net/smc: prepare for SMC-Rv2 connection
+    - net/smc: add SMC-Rv2 connection establishment
+    - net/smc: add listen processing for SMC-Rv2
+    - net/smc: add v2 format of CLC decline message
+    - net/smc: retrieve v2 gid from IB device
+    - net/smc: add v2 support to the work request layer
+    - net/smc: extend LLC layer for SMC-Rv2
+    - net/smc: add netlink support for SMC-Rv2
+    - net/smc: stop links when their GID is removed
+    - net/smc: fix kernel panic caused by race of smc_sock
+    - net/smc: Fix hung_task when removing SMC-R devices
+  * [22.04 FEAT] Transparent PCI device recovery (LP: #1959532)
+    - s390/pci: tolerate inconsistent handle in recover
+    - s390/pci: add simpler s390dbf traces for events
+    - s390/pci: refresh function handle in iomap
+    - s390/pci: implement reset_slot for hotplug slot
+    - PCI: Export pci_dev_lock()
+    - s390/pci: implement minimal PCI error recovery
+  * Mute/mic LEDs no function on some HP platfroms (LP: #1965080)
+    - ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machines
+  * [22.04 FEAT] smc: Add User-defined EID (Enterprise ID) Support - kernel
+    (LP: #1929060)
+    - net/smc: add support for user defined EIDs
+    - net/smc: keep static copy of system EID
+    - net/smc: add generic netlink support for system EID
+  * Rotate to 2021v1 signing key (LP: #1964990)
+    - [Packaging] Rotate to 2021v1 signing key
+  * [22.04 FEAT] zcrypt DD: Exploitation Support of new IBM Z Crypto Hardware
+    (kernel part) (LP: #1959547)
+    - s390/zcrypt: rework of debug feature messages
+    - s390/ap/zcrypt: debug feature improvements
+    - s390/zcrypt: CEX8S exploitation support
+    - s390/zcrypt: handle checkstopped cards with new state
+    - s390/zcrypt: Support CPRB minor version T7
+    - s390/zcrypt: change reply buffer size offering
+    - s390/zcrypt: Provide target domain for EP11 cprbs to scheduling function
+    - s390/airq: use DMA memory for summary indicators
+  * [22.04 FEAT] [VS2103] Set KVM_CAP_S390_MEM_OP_EXTENSION capability to 211
+    (LP: #1963901)
+    - SAUCE: Set KVM_CAP_S390_MEM_OP_EXTENSION capability to 211
+  * dependency on crda obsolete according to Debian (LP: #1958918)
+    - [Packaging] switch dependency from crda to wireless-regdb
+  * Cirrus audio support [1028:0BB5] & [1028:0BB6] (LP: #1964748)
+    - ALSA: hda/cs8409: Add new Warlock SKUs to patch_cs8409
+  * Miscellaneous Ubuntu changes
+    - [Packaging] mark dkms-build-configure--zfs executable
+    - [Packaging] Fix bashism in dkms-build script
+    - [Packaging] Always catch errors in dkms-build scripts
+    - [Config] toolchain version update
+  * Miscellaneous upstream changes
+    - Ubuntu: remove leftover reference to ubuntu/hio driver
+    - Reverting commits 61005756c824 and cdb0f8e66513 due to a conflict with
+      LP#1929035. Re-pick them afterwards, which will establish the upstream
+      commit content and order again.
+    - Revert "UBUNTU: [Packaging] Rotate to 2021v1 signing key"
+
+  [ Ubuntu: 5.15.0-23.23 ]
+
+  * jammy/linux: 5.15.0-23.23 -proposed tracker (LP: #1964573)
+  * Packaging resync (LP: #1786013)
+    - [Packaging] resync dkms-build{,--nvidia-N} from LRMv5
+    - debian/dkms-versions -- update from kernel-versions (main/master)
+  * [22.04 FEAT] KVM: Enable GISA support for Secure Execution guests
+    (LP: #1959977)
+    - KVM: s390: pv: make use of ultravisor AIV support
+  * intel_iommu breaks Intel IPU6 camera: isys port open ready failed -16
+    (LP: #1958004)
+    - SAUCE: iommu: intel-ipu: use IOMMU passthrough mode for Intel IPUs
+  * CVE-2022-23960
+    - ARM: report Spectre v2 status through sysfs
+    - ARM: early traps initialisation
+    - ARM: use LOADADDR() to get load address of sections
+    - ARM: Spectre-BHB workaround
+    - ARM: include unprivileged BPF status in Spectre V2 reporting
+    - arm64: Add Neoverse-N2, Cortex-A710 CPU part definition
+    - arm64: Add HWCAP for self-synchronising virtual counter
+    - arm64: Add Cortex-X2 CPU part definition
+    - arm64: add ID_AA64ISAR2_EL1 sys register
+    - arm64: cpufeature: add HWCAP for FEAT_AFP
+    - arm64: cpufeature: add HWCAP for FEAT_RPRES
+    - arm64: entry.S: Add ventry overflow sanity checks
+    - arm64: spectre: Rename spectre_v4_patch_fw_mitigation_conduit
+    - KVM: arm64: Allow indirect vectors to be used without SPECTRE_V3A
+    - arm64: entry: Make the trampoline cleanup optional
+    - arm64: entry: Free up another register on kpti's tramp_exit path
+    - arm64: entry: Move the trampoline data page before the text page
+    - arm64: entry: Allow tramp_alias to access symbols after the 4K boundary
+    - arm64: entry: Don't assume tramp_vectors is the start of the vectors
+    - arm64: entry: Move trampoline macros out of ifdef'd section
+    - arm64: entry: Make the kpti trampoline's kpti sequence optional
+    - arm64: entry: Allow the trampoline text to occupy multiple pages
+    - arm64: entry: Add non-kpti __bp_harden_el1_vectors for mitigations
+    - arm64: entry: Add vectors that have the bhb mitigation sequences
+    - arm64: entry: Add macro for reading symbol addresses from the trampoline
+    - arm64: Add percpu vectors for EL1
+    - arm64: proton-pack: Report Spectre-BHB vulnerabilities as part of Spectre-v2
+    - arm64: Mitigate spectre style branch history side channels
+    - KVM: arm64: Allow SMCCC_ARCH_WORKAROUND_3 to be discovered and migrated
+    - arm64: Use the clearbhb instruction in mitigations
+    - arm64: proton-pack: Include unprivileged eBPF status in Spectre v2
+      mitigation reporting
+    - ARM: fix build error when BPF_SYSCALL is disabled
+  * CVE-2021-26401
+    - x86/speculation: Use generic retpoline by default on AMD
+    - x86/speculation: Update link to AMD speculation whitepaper
+    - x86/speculation: Warn about Spectre v2 LFENCE mitigation
+    - x86/speculation: Warn about eIBRS + LFENCE + Unprivileged eBPF + SMT
+  * CVE-2022-0001
+    - x86,bugs: Unconditionally allow spectre_v2=retpoline,amd
+    - x86/speculation: Rename RETPOLINE_AMD to RETPOLINE_LFENCE
+    - x86/speculation: Add eIBRS + Retpoline options
+    - Documentation/hw-vuln: Update spectre doc
+    - x86/speculation: Include unprivileged eBPF status in Spectre v2 mitigation
+      reporting
+  * Jammy update: v5.15.27 upstream stable release (LP: #1964361)
+    - mac80211_hwsim: report NOACK frames in tx_status
+    - mac80211_hwsim: initialize ieee80211_tx_info at hw_scan_work
+    - i2c: bcm2835: Avoid clock stretching timeouts
+    - ASoC: rt5668: do not block workqueue if card is unbound
+    - ASoC: rt5682: do not block workqueue if card is unbound
+    - regulator: core: fix false positive in regulator_late_cleanup()
+    - Input: clear BTN_RIGHT/MIDDLE on buttonpads
+    - btrfs: get rid of warning on transaction commit when using flushoncommit
+    - KVM: arm64: vgic: Read HW interrupt pending state from the HW
+    - block: loop:use kstatfs.f_bsize of backing file to set discard granularity
+    - tipc: fix a bit overflow in tipc_crypto_key_rcv()
+    - cifs: do not use uninitialized data in the owner/group sid
+    - cifs: fix double free race when mount fails in cifs_get_root()
+    - cifs: modefromsids must add an ACE for authenticated users
+    - selftests/seccomp: Fix seccomp failure by adding missing headers
+    - drm/amd/pm: correct UMD pstate clocks for Dimgrey Cavefish and Beige Goby
+    - dmaengine: shdma: Fix runtime PM imbalance on error
+    - i2c: cadence: allow COMPILE_TEST
+    - i2c: imx: allow COMPILE_TEST
+    - i2c: qup: allow COMPILE_TEST
+    - net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
+    - block-map: add __GFP_ZERO flag for alloc_page in function bio_copy_kern
+    - usb: gadget: don't release an existing dev->buf
+    - usb: gadget: clear related members when goto fail
+    - exfat: reuse exfat_inode_info variable instead of calling EXFAT_I()
+    - exfat: fix i_blocks for files truncated over 4 GiB
+    - tracing: Add test for user space strings when filtering on string pointers
+    - arm64: Mark start_backtrace() notrace and NOKPROBE_SYMBOL
+    - serial: stm32: prevent TDR register overwrite when sending x_char
+    - ext4: drop ineligible txn start stop APIs
+    - ext4: simplify updating of fast commit stats
+    - ext4: fast commit may not fallback for ineligible commit
+    - ext4: fast commit may miss file actions
+    - sched/fair: Fix fault in reweight_entity
+    - ata: pata_hpt37x: fix PCI clock detection
+    - drm/amdgpu: check vm ready by amdgpu_vm->evicting flag
+    - tracing: Add ustring operation to filtering string pointers
+    - ipv6: fix skb drops in igmp6_event_query() and igmp6_event_report()
+    - NFSD: Have legacy NFSD WRITE decoders use xdr_stream_subsegment()
+    - NFSD: Fix zero-length NFSv3 WRITEs
+    - io_uring: fix no lock protection for ctx->cq_extra
+    - tools/resolve_btf_ids: Close ELF file on error
+    - mtd: spi-nor: Fix mtd size for s3an flashes
+    - MIPS: fix local_{add,sub}_return on MIPS64
+    - signal: In get_signal test for signal_group_exit every time through the loop
+    - PCI: mediatek-gen3: Disable DVFSRC voltage request
+    - PCI: rcar: Check if device is runtime suspended instead of
+      __clk_is_enabled()
+    - PCI: dwc: Do not remap invalid res
+    - PCI: aardvark: Fix checking for MEM resource type
+    - KVM: VMX: Don't unblock vCPU w/ Posted IRQ if IRQs are disabled in guest
+    - KVM: s390: Ensure kvm_arch_no_poll() is read once when blocking vCPU
+    - KVM: VMX: Read Posted Interrupt "control" exactly once per loop iteration
+    - KVM: X86: Ensure that dirty PDPTRs are loaded
+    - KVM: x86: Handle 32-bit wrap of EIP for EMULTYPE_SKIP with flat code seg
+    - KVM: x86: Exit to userspace if emulation prepared a completion callback
+    - i3c: fix incorrect address slot lookup on 64-bit
+    - i3c/master/mipi-i3c-hci: Fix a potentially infinite loop in
+      'hci_dat_v1_get_index()'
+    - tracing: Do not let synth_events block other dyn_event systems during create
+    - Input: ti_am335x_tsc - set ADCREFM for X configuration
+    - Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2
+    - PCI: mvebu: Check for errors from pci_bridge_emul_init() call
+    - PCI: mvebu: Do not modify PCI IO type bits in conf_write
+    - PCI: mvebu: Fix support for bus mastering and PCI_COMMAND on emulated bridge
+    - PCI: mvebu: Fix configuring secondary bus of PCIe Root Port via emulated
+      bridge
+    - PCI: mvebu: Setup PCIe controller to Root Complex mode
+    - PCI: mvebu: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
+    - PCI: mvebu: Fix support for PCI_EXP_DEVCTL on emulated bridge
+    - PCI: mvebu: Fix support for PCI_EXP_RTSTA on emulated bridge
+    - PCI: mvebu: Fix support for DEVCAP2, DEVCTL2 and LNKCTL2 registers on
+      emulated bridge
+    - NFSD: Fix verifier returned in stable WRITEs
+    - Revert "nfsd: skip some unnecessary stats in the v4 case"
+    - nfsd: fix crash on COPY_NOTIFY with special stateid
+    - x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
+    - drm/i915: don't call free_mmap_offset when purging
+    - SUNRPC: Fix sockaddr handling in the svc_xprt_create_error trace point
+    - SUNRPC: Fix sockaddr handling in svcsock_accept_class trace points
+    - drm/sun4i: dw-hdmi: Fix missing put_device() call in sun8i_hdmi_phy_get
+    - drm/atomic: Check new_crtc_state->active to determine if CRTC needs disable
+      in self refresh mode
+    - ntb_hw_switchtec: Fix pff ioread to read into mmio_part_cfg_all
+    - ntb_hw_switchtec: Fix bug with more than 32 partitions
+    - drm/amdkfd: Check for null pointer after calling kmemdup
+    - drm/amdgpu: use spin_lock_irqsave to avoid deadlock by local interrupt
+    - i3c: master: dw: check return of dw_i3c_master_get_free_pos()
+    - dma-buf: cma_heap: Fix mutex locking section
+    - tracing/uprobes: Check the return value of kstrdup() for tu->filename
+    - tracing/probes: check the return value of kstrndup() for pbuf
+    - mm: defer kmemleak object creation of module_alloc()
+    - kasan: fix quarantine conflicting with init_on_free
+    - selftests/vm: make charge_reserved_hugetlb.sh work with existing cgroup
+      setting
+    - hugetlbfs: fix off-by-one error in hugetlb_vmdelete_list()
+    - drm/amdgpu/display: Only set vblank_disable_immediate when PSR is not
+      enabled
+    - drm/amdgpu: filter out radeon PCI device IDs
+    - drm/amdgpu: filter out radeon secondary ids as well
+    - drm/amd/display: Use adjusted DCN301 watermarks
+    - drm/amd/display: move FPU associated DSC code to DML folder
+    - ethtool: Fix link extended state for big endian
+    - octeontx2-af: Optimize KPU1 processing for variable-length headers
+    - octeontx2-af: Reset PTP config in FLR handler
+    - octeontx2-af: cn10k: RPM hardware timestamp configuration
+    - octeontx2-af: cn10k: Use appropriate register for LMAC enable
+    - octeontx2-af: Adjust LA pointer for cpt parse header
+    - octeontx2-af: Add KPU changes to parse NGIO as separate layer
+    - net/mlx5e: IPsec: Refactor checksum code in tx data path
+    - net/mlx5e: IPsec: Fix crypto offload for non TCP/UDP encapsulated traffic
+    - bpf: Use u64_stats_t in struct bpf_prog_stats
+    - bpf: Fix possible race in inc_misses_counter
+    - drm/amd/display: Update watermark values for DCN301
+    - drm: mxsfb: Set fallback bus format when the bridge doesn't provide one
+    - drm: mxsfb: Fix NULL pointer dereference
+    - riscv/mm: Add XIP_FIXUP for phys_ram_base
+    - drm/i915/display: split out dpt out of intel_display.c
+    - drm/i915/display: Move DRRS code its own file
+    - drm/i915: Disable DRRS on IVB/HSW port != A
+    - gve: Recording rx queue before sending to napi
+    - net: dsa: ocelot: seville: utilize of_mdiobus_register
+    - net: dsa: seville: register the mdiobus under devres
+    - ibmvnic: don't release napi in __ibmvnic_open()
+    - of: net: move of_net under net/
+    - net: ethernet: litex: Add the dependency on HAS_IOMEM
+    - drm/mediatek: mtk_dsi: Reset the dsi0 hardware
+    - cifs: protect session channel fields with chan_lock
+    - cifs: fix confusing unneeded warning message on smb2.1 and earlier
+    - drm/amd/display: Fix stream->link_enc unassigned during stream removal
+    - bnxt_en: Fix occasional ethtool -t loopback test failures
+    - drm/amd/display: For vblank_disable_immediate, check PSR is really used
+    - PCI: mvebu: Fix device enumeration regression
+    - net: of: fix stub of_net helpers for CONFIG_NET=n
+    - ALSA: intel_hdmi: Fix reference to PCM buffer address
+    - ucounts: Fix systemd LimitNPROC with private users regression
+    - riscv/efi_stub: Fix get_boot_hartid_from_fdt() return value
+    - riscv: Fix config KASAN && SPARSEMEM && !SPARSE_VMEMMAP
+    - riscv: Fix config KASAN && DEBUG_VIRTUAL
+    - iwlwifi: mvm: check debugfs_dir ptr before use
+    - ASoC: ops: Shift tested values in snd_soc_put_volsw() by +min
+    - iommu/vt-d: Fix double list_add when enabling VMD in scalable mode
+    - iommu/amd: Recover from event log overflow
+    - drm/i915: s/JSP2/ICP2/ PCH
+    - drm/amd/display: Reduce dmesg error to a debug print
+    - xen/netfront: destroy queues before real_num_tx_queues is zeroed
+    - thermal: core: Fix TZ_GET_TRIP NULL pointer dereference
+    - mac80211: fix EAPoL rekey fail in 802.3 rx path
+    - blktrace: fix use after free for struct blk_trace
+    - ntb: intel: fix port config status offset for SPR
+    - mm: Consider __GFP_NOWARN flag for oversized kvmalloc() calls
+    - xfrm: fix MTU regression
+    - netfilter: fix use-after-free in __nf_register_net_hook()
+    - bpf, sockmap: Do not ignore orig_len parameter
+    - xfrm: fix the if_id check in changelink
+    - xfrm: enforce validity of offload input flags
+    - e1000e: Correct NVM checksum verification flow
+    - net: fix up skbs delta_truesize in UDP GRO frag_list
+    - netfilter: nf_queue: don't assume sk is full socket
+    - netfilter: nf_queue: fix possible use-after-free
+    - netfilter: nf_queue: handle socket prefetch
+    - batman-adv: Request iflink once in batadv-on-batadv check
+    - batman-adv: Request iflink once in batadv_get_real_netdevice
+    - batman-adv: Don't expect inter-netns unique iflink indices
+    - net: ipv6: ensure we call ipv6_mc_down() at most once
+    - net: dcb: flush lingering app table entries for unregistered devices
+    - net: ipa: add an interconnect dependency
+    - net/smc: fix connection leak
+    - net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error generated by client
+    - net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error cause by server
+    - btrfs: fix ENOSPC failure when attempting direct IO write into NOCOW range
+    - mac80211: fix forwarded mesh frames AC & queue selection
+    - net: stmmac: fix return value of __setup handler
+    - mac80211: treat some SAE auth steps as final
+    - iavf: Fix missing check for running netdev
+    - net: sxgbe: fix return value of __setup handler
+    - ibmvnic: register netdev after init of adapter
+    - net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe()
+    - ixgbe: xsk: change !netif_carrier_ok() handling in ixgbe_xmit_zc()
+    - iavf: Fix deadlock in iavf_reset_task
+    - efivars: Respect "block" flag in efivar_entry_set_safe()
+    - auxdisplay: lcd2s: Fix lcd2s_redefine_char() feature
+    - firmware: arm_scmi: Remove space in MODULE_ALIAS name
+    - ASoC: cs4265: Fix the duplicated control name
+    - auxdisplay: lcd2s: Fix memory leak in ->remove()
+    - auxdisplay: lcd2s: Use proper API to free the instance of charlcd object
+    - can: gs_usb: change active_channels's type from atomic_t to u8
+    - iommu/tegra-smmu: Fix missing put_device() call in tegra_smmu_find
+    - arm64: dts: rockchip: Switch RK3399-Gru DP to SPDIF output
+    - igc: igc_read_phy_reg_gpy: drop premature return
+    - ARM: Fix kgdb breakpoint for Thumb2
+    - mips: setup: fix setnocoherentio() boolean setting
+    - ARM: 9182/1: mmu: fix returns from early_param() and __setup() functions
+    - mptcp: Correctly set DATA_FIN timeout when number of retransmits is large
+    - selftests: mlxsw: tc_police_scale: Make test more robust
+    - pinctrl: sunxi: Use unique lockdep classes for IRQs
+    - igc: igc_write_phy_reg_gpy: drop premature return
+    - ibmvnic: free reset-work-item when flushing
+    - memfd: fix F_SEAL_WRITE after shmem huge page allocated
+    - s390/extable: fix exception table sorting
+    - sched: Fix yet more sched_fork() races
+    - arm64: dts: juno: Remove GICv2m dma-range
+    - iommu/amd: Fix I/O page table memory leak
+    - MIPS: ralink: mt7621: do memory detection on KSEG1
+    - ARM: dts: switch timer config to common devkit8000 devicetree
+    - ARM: dts: Use 32KiHz oscillator on devkit8000
+    - soc: fsl: guts: Revert commit 3c0d64e867ed
+    - soc: fsl: guts: Add a missing memory allocation failure check
+    - soc: fsl: qe: Check of ioremap return value
+    - netfilter: nf_tables: prefer kfree_rcu(ptr, rcu) variant
+    - ARM: tegra: Move panels to AUX bus
+    - can: etas_es58x: change opened_channel_cnt's type from atomic_t to u8
+    - net: stmmac: enhance XDP ZC driver level switching performance
+    - net: stmmac: only enable DMA interrupts when ready
+    - ibmvnic: initialize rc before completing wait
+    - ibmvnic: define flush_reset_queue helper
+    - ibmvnic: complete init_done on transport events
+    - net: chelsio: cxgb3: check the return value of pci_find_capability()
+    - net: sparx5: Fix add vlan when invalid operation
+    - iavf: Refactor iavf state machine tracking
+    - iavf: Add __IAVF_INIT_FAILED state
+    - iavf: Combine init and watchdog state machines
+    - iavf: Add trace while removing device
+    - iavf: Rework mutexes for better synchronisation
+    - iavf: Add helper function to go from pci_dev to adapter
+    - iavf: Fix kernel BUG in free_msi_irqs
+    - iavf: Add waiting so the port is initialized in remove
+    - iavf: Fix init state closure on remove
+    - iavf: Fix locking for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS
+    - iavf: Fix race in init state
+    - iavf: Fix __IAVF_RESETTING state usage
+    - drm/i915/guc/slpc: Correct the param count for unset param
+    - drm/bridge: ti-sn65dsi86: Properly undo autosuspend
+    - e1000e: Fix possible HW unit hang after an s0ix exit
+    - MIPS: ralink: mt7621: use bitwise NOT instead of logical
+    - nl80211: Handle nla_memdup failures in handle_nan_filter
+    - drm/amdgpu: fix suspend/resume hang regression
+    - net: dcb: disable softirqs in dcbnl_flush_dev()
+    - selftests: mlxsw: resource_scale: Fix return value
+    - net: stmmac: perserve TX and RX coalesce value during XDP setup
+    - iavf: do not override the adapter state in the watchdog task (again)
+    - iavf: missing unlocks in iavf_watchdog_task()
+    - MAINTAINERS: adjust file entry for of_net.c after movement
+    - Input: elan_i2c - move regulator_[en|dis]able() out of
+      elan_[en|dis]able_power()
+    - Input: elan_i2c - fix regulator enable count imbalance after suspend/resume
+    - Input: samsung-keypad - properly state IOMEM dependency
+    - HID: add mapping for KEY_DICTATE
+    - HID: add mapping for KEY_ALL_APPLICATIONS
+    - tracing/histogram: Fix sorting on old "cpu" value
+    - tracing: Fix return value of __setup handlers
+    - btrfs: fix lost prealloc extents beyond eof after full fsync
+    - btrfs: fix relocation crash due to premature return from
+      btrfs_commit_transaction()
+    - btrfs: do not WARN_ON() if we have PageError set
+    - btrfs: qgroup: fix deadlock between rescan worker and remove qgroup
+    - btrfs: add missing run of delayed items after unlink during log replay
+    - btrfs: do not start relocation until in progress drops are done
+    - Revert "xfrm: xfrm_state_mtu should return at least 1280 for ipv6"
+    - proc: fix documentation and description of pagemap
+    - KVM: x86/mmu: Passing up the error state of mmu_alloc_shadow_roots()
+    - hamradio: fix macro redefine warning
+    - Linux 5.15.27
+    - [Config] updateconfigs
+  * devices on thunderbolt dock are not recognized on adl-p platform
+    (LP: #1955016)
+    - thunderbolt: Tear down existing tunnels when resuming from hibernate
+    - thunderbolt: Runtime resume USB4 port when retimers are scanned
+    - thunderbolt: Do not allow subtracting more NFC credits than configured
+    - thunderbolt: Do not program path HopIDs for USB4 routers
+    - thunderbolt: Add debug logging of DisplayPort resource allocation
+  * MT7921[14c3:7961] ASPM is disabled and it affects power consumption
+    (LP: #1955882)
+    - mt76: mt7921: enable aspm by default
+  * Add proper runtime PM support to Realtek PCIe cardreader (LP: #1963615)
+    - mmc: rtsx: Use pm_runtime_{get, put}() to handle runtime PM
+    - misc: rtsx: Rework runtime power management flow
+    - misc: rtsx: Cleanup power management ops
+    - misc: rtsx: Quiesce rts5249 on system suspend
+    - mmc: rtsx: Let MMC core handle runtime PM
+    - misc: rtsx: conditionally build rtsx_pm_power_saving()
+    - misc: rtsx: rts522a rts5228 rts5261 support Runtime PM
+    - mmc: rtsx: Fix build errors/warnings for unused variable
+    - mmc: rtsx: add 74 Clocks in power on flow
+  * [22.04 FEAT] In-kernel crypto: SIMD implementation of chacha20
+    (LP: #1853152)
+    - s390/crypto: add SIMD implementation for ChaCha20
+    - s390/crypto: fix compile error for ChaCha20 module
+  * Add ConnectX7 support and bug fixes  to Jammy (LP: #1962185)
+    - IB/mlx5: Expose NDR speed through MAD
+  * INVALID or PRIVATE BUG (LP: #1959890)
+    - [Config] Deactivate CONFIG_QETH_OSX kernel config option
+  * Move virtual graphics drivers from linux-modules-extra to linux-modules
+    (LP: #1960633)
+    - [Packaging] Move VM DRM drivers into modules
+  * Not able to enter s2idle state on AMD platforms (LP: #1961121)
+    - HID: amd_sfh: Handle amd_sfh work buffer in PM ops
+    - HID: amd_sfh: Disable the interrupt for all command
+    - HID: amd_sfh: Add functionality to clear interrupts
+    - HID: amd_sfh: Add interrupt handler to process interrupts
+  * INVALID or PRIVATE BUG (LP: #1960580)
+    - s390/kexec_file: move kernel image size check
+    - s390: support command lines longer than 896 bytes
+  * [UBUNTU 20.04] kernel: Add support for CPU-MF counter second version 7
+    (LP: #1960182)
+    - s390/cpumf: Support for CPU Measurement Facility CSVN 7
+    - s390/cpumf: Support for CPU Measurement Sampling Facility LS bit
+  * [SRU]PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is
+    enabled by IOMMU (LP: #1937295)
+    - PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled
+      by IOMMU
+  * Jammy update: v5.15.26 upstream stable release (LP: #1963891)
+    - mm/filemap: Fix handling of THPs in generic_file_buffered_read()
+    - cgroup/cpuset: Fix a race between cpuset_attach() and cpu hotplug
+    - cgroup-v1: Correct privileges check in release_agent writes
+    - x86/ptrace: Fix xfpregs_set()'s incorrect xmm clearing
+    - btrfs: tree-checker: check item_size for inode_item
+    - btrfs: tree-checker: check item_size for dev_item
+    - clk: jz4725b: fix mmc0 clock gating
+    - io_uring: don't convert to jiffies for waiting on timeouts
+    - io_uring: disallow modification of rsrc_data during quiesce
+    - selinux: fix misuse of mutex_is_locked()
+    - vhost/vsock: don't check owner in vhost_vsock_stop() while releasing
+    - parisc/unaligned: Fix fldd and fstd unaligned handlers on 32-bit kernel
+    - parisc/unaligned: Fix ldw() and stw() unalignment handlers
+    - KVM: x86/mmu: make apf token non-zero to fix bug
+    - drm/amd/display: Protect update_bw_bounding_box FPU code.
+    - drm/amd/pm: fix some OEM SKU specific stability issues
+    - drm/amd: Check if ASPM is enabled from PCIe subsystem
+    - drm/amdgpu: disable MMHUB PG for Picasso
+    - drm/amdgpu: do not enable asic reset for raven2
+    - drm/i915: Widen the QGV point mask
+    - drm/i915: Correctly populate use_sagv_wm for all pipes
+    - drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV
+    - sr9700: sanity check for packet length
+    - USB: zaurus: support another broken Zaurus
+    - CDC-NCM: avoid overflow in sanity checking
+    - netfilter: xt_socket: fix a typo in socket_mt_destroy()
+    - netfilter: xt_socket: missing ifdef CONFIG_IP6_NF_IPTABLES dependency
+    - tee: export teedev_open() and teedev_close_context()
+    - optee: use driver internal tee_context for some rpc
+    - ping: remove pr_err from ping_lookup
+    - Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
+    - gpu: host1x: Always return syncpoint value when waiting
+    - perf evlist: Fix failed to use cpu list for uncore events
+    - perf data: Fix double free in perf_session__delete()
+    - mptcp: fix race in incoming ADD_ADDR option processing
+    - mptcp: add mibs counter for ignored incoming options
+    - selftests: mptcp: fix diag instability
+    - selftests: mptcp: be more conservative with cookie MPJ limits
+    - bnx2x: fix driver load from initrd
+    - bnxt_en: Fix active FEC reporting to ethtool
+    - bnxt_en: Fix offline ethtool selftest with RDMA enabled
+    - bnxt_en: Fix incorrect multicast rx mask setting when not requested
+    - hwmon: Handle failure to register sensor with thermal zone correctly
+    - net/mlx5: Fix tc max supported prio for nic mode
+    - ice: check the return of ice_ptp_gettimex64
+    - ice: initialize local variable 'tlv'
+    - net/mlx5: Update the list of the PCI supported devices
+    - bpf: Fix crash due to incorrect copy_map_value
+    - bpf: Do not try bpf_msg_push_data with len 0
+    - selftests: bpf: Check bpf_msg_push_data return value
+    - bpf: Fix a bpf_timer initialization issue
+    - bpf: Add schedule points in batch ops
+    - io_uring: add a schedule point in io_add_buffers()
+    - net: __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor friends
+    - nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
+    - tipc: Fix end of loop tests for list_for_each_entry()
+    - gso: do not skip outer ip header in case of ipip and net_failover
+    - net: mv643xx_eth: process retval from of_get_mac_address
+    - openvswitch: Fix setting ipv6 fields causing hw csum failure
+    - drm/edid: Always set RGB444
+    - net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
+    - drm/vc4: crtc: Fix runtime_pm reference counting
+    - drm/i915/dg2: Print PHY name properly on calibration error
+    - net/sched: act_ct: Fix flow table lookup after ct clear or switching zones
+    - net: ll_temac: check the return value of devm_kmalloc()
+    - net: Force inlining of checksum functions in net/checksum.h
+    - netfilter: nf_tables: unregister flowtable hooks on netns exit
+    - nfp: flower: Fix a potential leak in nfp_tunnel_add_shared_mac()
+    - net: mdio-ipq4019: add delay after clock enable
+    - netfilter: nf_tables: fix memory leak during stateful obj update
+    - net/smc: Use a mutex for locking "struct smc_pnettable"
+    - surface: surface3_power: Fix battery readings on batteries without a serial
+      number
+    - udp_tunnel: Fix end of loop test in udp_tunnel_nic_unregister()
+    - net/mlx5: DR, Cache STE shadow memory
+    - ibmvnic: schedule failover only if vioctl fails
+    - net/mlx5: DR, Don't allow match on IP w/o matching on full
+      ethertype/ip_version
+    - net/mlx5: Fix possible deadlock on rule deletion
+    - net/mlx5: Fix wrong limitation of metadata match on ecpf
+    - net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
+    - net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
+    - net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
+    - net/mlx5: Update log_max_qp value to be 17 at most
+    - spi: spi-zynq-qspi: Fix a NULL pointer dereference in
+      zynq_qspi_exec_mem_op()
+    - gpio: rockchip: Reset int_bothedge when changing trigger
+    - regmap-irq: Update interrupt clear register for proper reset
+    - net-timestamp: convert sk->sk_tskey to atomic_t
+    - RDMA/rtrs-clt: Fix possible double free in error case
+    - RDMA/rtrs-clt: Move free_permit from free_clt to rtrs_clt_close
+    - bnxt_en: Increase firmware message response DMA wait time
+    - configfs: fix a race in configfs_{,un}register_subsystem()
+    - RDMA/ib_srp: Fix a deadlock
+    - tracing: Dump stacktrace trigger to the corresponding instance
+    - tracing: Have traceon and traceoff trigger honor the instance
+    - iio:imu:adis16480: fix buffering for devices with no burst mode
+    - iio: adc: men_z188_adc: Fix a resource leak in an error handling path
+    - iio: adc: tsc2046: fix memory corruption by preventing array overflow
+    - iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
+    - iio: accel: fxls8962af: add padding to regmap for SPI
+    - iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
+    - iio: Fix error handling for PM
+    - sc16is7xx: Fix for incorrect data being transmitted
+    - ata: pata_hpt37x: disable primary channel on HPT371
+    - Revert "USB: serial: ch341: add new Product ID for CH341A"
+    - usb: gadget: rndis: add spinlock for rndis response list
+    - USB: gadget: validate endpoint index for xilinx udc
+    - tracefs: Set the group ownership in apply_options() not parse_options()
+    - USB: serial: option: add support for DW5829e
+    - USB: serial: option: add Telit LE910R1 compositions
+    - usb: dwc2: drd: fix soft connect when gadget is unconfigured
+    - usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail
+    - usb: dwc3: pci: Fix Bay Trail phy GPIO mappings
+    - usb: dwc3: gadget: Let the interrupt handler disable bottom halves.
+    - xhci: re-initialize the HC during resume if HCE was set
+    - xhci: Prevent futile URB re-submissions due to incorrect return value.
+    - nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
+    - mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
+    - driver core: Free DMA range map when device is released
+    - btrfs: prevent copying too big compressed lzo segment
+    - RDMA/cma: Do not change route.addr.src_addr outside state checks
+    - thermal: int340x: fix memory leak in int3400_notify()
+    - staging: fbtft: fb_st7789v: reset display before initialization
+    - tps6598x: clear int mask on probe failure
+    - IB/qib: Fix duplicate sysfs directory name
+    - riscv: fix nommu_k210_sdcard_defconfig
+    - riscv: fix oops caused by irqsoff latency tracer
+    - tty: n_gsm: fix encoding of control signal octet bit DV
+    - tty: n_gsm: fix proper link termination after failed open
+    - tty: n_gsm: fix NULL pointer access due to DLCI release
+    - tty: n_gsm: fix wrong tty control line for flow control
+    - tty: n_gsm: fix wrong modem processing in convergence layer type 2
+    - tty: n_gsm: fix deadlock in gsmtty_open()
+    - pinctrl: fix loop in k210_pinconf_get_drive()
+    - pinctrl: k210: Fix bias-pull-up
+    - gpio: tegra186: Fix chip_data type confusion
+    - memblock: use kfree() to release kmalloced memblock regions
+    - ice: Fix race conditions between virtchnl handling and VF ndo ops
+    - ice: fix concurrent reset and removal of VFs
+    - Linux 5.15.26
+  * Jammy update: v5.15.25 upstream stable release (LP: #1963890)
+    - drm/nouveau/pmu/gm200-: use alternate falcon reset sequence
+    - fs/proc: task_mmu.c: don't read mapcount for migration entry
+    - btrfs: zoned: cache reported zone during mount
+    - HID:Add support for UGTABLET WP5540
+    - Revert "svm: Add warning message for AVIC IPI invalid target"
+    - parisc: Show error if wrong 32/64-bit compiler is being used
+    - serial: parisc: GSC: fix build when IOSAPIC is not set
+    - parisc: Drop __init from map_pages declaration
+    - parisc: Fix data TLB miss in sba_unmap_sg
+    - parisc: Fix sglist access in ccio-dma.c
+    - mmc: block: fix read single on recovery logic
+    - mm: don't try to NUMA-migrate COW pages that have other uses
+    - HID: amd_sfh: Add illuminance mask to limit ALS max value
+    - HID: i2c-hid: goodix: Fix a lockdep splat
+    - HID: amd_sfh: Increase sensor command timeout
+    - HID: amd_sfh: Correct the structure field name
+    - PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA
+      topology
+    - parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()
+    - btrfs: send: in case of IO error log it
+    - platform/x86: touchscreen_dmi: Add info for the RWC NANOTE P8 AY07J 2-in-1
+    - platform/x86: ISST: Fix possible circular locking dependency detected
+    - kunit: tool: Import missing importlib.abc
+    - selftests: rtc: Increase test timeout so that all tests run
+    - kselftest: signal all child processes
+    - net: ieee802154: at86rf230: Stop leaking skb's
+    - selftests/zram: Skip max_comp_streams interface on newer kernel
+    - selftests/zram01.sh: Fix compression ratio calculation
+    - selftests/zram: Adapt the situation that /dev/zram0 is being used
+    - selftests: openat2: Print also errno in failure messages
+    - selftests: openat2: Add missing dependency in Makefile
+    - selftests: openat2: Skip testcases that fail with EOPNOTSUPP
+    - selftests: skip mincore.check_file_mmap when fs lacks needed support
+    - ax25: improve the incomplete fix to avoid UAF and NPD bugs
+    - pinctrl: bcm63xx: fix unmet dependency on REGMAP for GPIO_REGMAP
+    - vfs: make freeze_super abort when sync_filesystem returns error
+    - quota: make dquot_quota_sync return errors from ->sync_fs
+    - scsi: pm80xx: Fix double completion for SATA devices
+    - kselftest: Fix vdso_test_abi return status
+    - scsi: core: Reallocate device's budget map on queue depth change
+    - scsi: pm8001: Fix use-after-free for aborted TMF sas_task
+    - scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task
+    - drm/amd: Warn users about potential s0ix problems
+    - nvme: fix a possible use-after-free in controller reset during load
+    - nvme-tcp: fix possible use-after-free in transport error_recovery work
+    - nvme-rdma: fix possible use-after-free in transport error_recovery work
+    - net: sparx5: do not refer to skb after passing it on
+    - drm/amd: add support to check whether the system is set to s3
+    - drm/amd: Only run s3 or s0ix if system is configured properly
+    - drm/amdgpu: fix logic inversion in check
+    - x86/Xen: streamline (and fix) PV CPU enumeration
+    - Revert "module, async: async_synchronize_full() on module init iff async is
+      used"
+    - gcc-plugins/stackleak: Use noinstr in favor of notrace
+    - random: wake up /dev/random writers after zap
+    - KVM: x86/xen: Fix runstate updates to be atomic when preempting vCPU
+    - KVM: x86: nSVM/nVMX: set nested_run_pending on VM entry which is a result of
+      RSM
+    - KVM: x86: SVM: don't passthrough SMAP/SMEP/PKE bits in !NPT && !gCR0.PG case
+    - KVM: x86: nSVM: fix potential NULL derefernce on nested migration
+    - KVM: x86: nSVM: mark vmcb01 as dirty when restoring SMM saved state
+    - iwlwifi: fix use-after-free
+    - drm/radeon: Fix backlight control on iMac 12,1
+    - drm/atomic: Don't pollute crtc_state->mode_blob with error pointers
+    - drm/amd/pm: correct the sequence of sending gpu reset msg
+    - drm/amdgpu: skipping SDMA hw_init and hw_fini for S0ix.
+    - drm/i915/opregion: check port number bounds for SWSCI display power state
+    - drm/i915: Fix dbuf slice config lookup
+    - drm/i915: Fix mbus join config lookup
+    - vsock: remove vsock from connected table when connect is interrupted by a
+      signal
+    - drm/cma-helper: Set VM_DONTEXPAND for mmap
+    - drm/i915/gvt: Make DRM_I915_GVT depend on X86
+    - drm/i915/ttm: tweak priority hint selection
+    - iwlwifi: pcie: fix locking when "HW not ready"
+    - iwlwifi: pcie: gen2: fix locking when "HW not ready"
+    - iwlwifi: mvm: don't send SAR GEO command for 3160 devices
+    - selftests: netfilter: fix exit value for nft_concat_range
+    - netfilter: nft_synproxy: unregister hooks on init error path
+    - selftests: netfilter: disable rp_filter on router
+    - ipv4: fix data races in fib_alias_hw_flags_set
+    - ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
+    - ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
+    - ipv6: per-netns exclusive flowlabel checks
+    - Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
+    - mac80211: mlme: check for null after calling kmemdup
+    - brcmfmac: firmware: Fix crash in brcm_alt_fw_path
+    - cfg80211: fix race in netlink owner interface destruction
+    - net: dsa: lan9303: fix reset on probe
+    - net: dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
+    - net: dsa: lantiq_gswip: fix use after free in gswip_remove()
+    - net: dsa: lan9303: handle hwaccel VLAN tags
+    - net: dsa: lan9303: add VLAN IDs to master device
+    - net: ieee802154: ca8210: Fix lifs/sifs periods
+    - ping: fix the dif and sdif check in ping_lookup
+    - bonding: force carrier update when releasing slave
+    - drop_monitor: fix data-race in dropmon_net_event / trace_napi_poll_hit
+    - net_sched: add __rcu annotation to netdev->qdisc
+    - bonding: fix data-races around agg_select_timer
+    - libsubcmd: Fix use-after-free for realloc(..., 0)
+    - net/smc: Avoid overwriting the copies of clcsock callback functions
+    - net: phy: mediatek: remove PHY mode check on MT7531
+    - atl1c: fix tx timeout after link flap on Mikrotik 10/25G NIC
+    - tipc: fix wrong publisher node address in link publications
+    - dpaa2-switch: fix default return of dpaa2_switch_flower_parse_mirror_key
+    - dpaa2-eth: Initialize mutex used in one step timestamping path
+    - net: bridge: multicast: notify switchdev driver whenever MC processing gets
+      disabled
+    - perf bpf: Defer freeing string after possible strlen() on it
+    - selftests/exec: Add non-regular to TEST_GEN_PROGS
+    - arm64: Correct wrong label in macro __init_el2_gicv3
+    - ALSA: usb-audio: revert to IMPLICIT_FB_FIXED_DEV for M-Audio FastTrack Ultra
+    - ALSA: hda/realtek: Add quirk for Legion Y9000X 2019
+    - ALSA: hda/realtek: Fix deadlock by COEF mutex
+    - ALSA: hda: Fix regression on forced probe mask option
+    - ALSA: hda: Fix missing codec probe on Shenker Dock 15
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_range()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_sx()
+    - ASoC: ops: Fix stereo change notifications in snd_soc_put_xr_sx()
+    - cifs: fix set of group SID via NTSD xattrs
+    - powerpc/603: Fix boot failure with DEBUG_PAGEALLOC and KFENCE
+    - powerpc/lib/sstep: fix 'ptesync' build error
+    - mtd: rawnand: gpmi: don't leak PM reference in error path
+    - smb3: fix snapshot mount option
+    - tipc: fix wrong notification node addresses
+    - scsi: ufs: Remove dead code
+    - scsi: ufs: Fix a deadlock in the error handler
+    - ASoC: tas2770: Insert post reset delay
+    - ASoC: qcom: Actually clear DMA interrupt register for HDMI
+    - block/wbt: fix negative inflight counter when remove scsi device
+    - NFS: Remove an incorrect revalidation in nfs4_update_changeattr_locked()
+    - NFS: LOOKUP_DIRECTORY is also ok with symlinks
+    - NFS: Do not report writeback errors in nfs_getattr()
+    - tty: n_tty: do not look ahead for EOL character past the end of the buffer
+    - block: fix surprise removal for drivers calling blk_set_queue_dying
+    - mtd: rawnand: qcom: Fix clock sequencing in qcom_nandc_probe()
+    - mtd: parsers: qcom: Fix kernel panic on skipped partition
+    - mtd: parsers: qcom: Fix missing free for pparts in cleanup
+    - mtd: phram: Prevent divide by zero bug in phram_setup()
+    - mtd: rawnand: brcmnand: Fixed incorrect sub-page ECC status
+    - HID: elo: fix memory leak in elo_probe
+    - mtd: rawnand: ingenic: Fix missing put_device in ingenic_ecc_get
+    - Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj
+    - KVM: x86/pmu: Refactoring find_arch_event() to pmc_perf_hw_id()
+    - KVM: x86/pmu: Don't truncate the PerfEvtSeln MSR when creating a perf event
+    - KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW
+    - ARM: OMAP2+: hwmod: Add of_node_put() before break
+    - ARM: OMAP2+: adjust the location of put_device() call in omapdss_init_of
+    - phy: usb: Leave some clocks running during suspend
+    - staging: vc04_services: Fix RCU dereference check
+    - phy: phy-mtk-tphy: Fix duplicated argument in phy-mtk-tphy
+    - irqchip/sifive-plic: Add missing thead,c900-plic match string
+    - x86/bug: Merge annotate_reachable() into _BUG_FLAGS() asm
+    - netfilter: conntrack: don't refresh sctp entries in closed state
+    - ksmbd: fix same UniqueId for dot and dotdot entries
+    - ksmbd: don't align last entry offset in smb2 query directory
+    - arm64: dts: meson-gx: add ATF BL32 reserved-memory region
+    - arm64: dts: meson-g12: add ATF BL32 reserved-memory region
+    - arm64: dts: meson-g12: drop BL32 region from SEI510/SEI610
+    - pidfd: fix test failure due to stack overflow on some arches
+    - selftests: fixup build warnings in pidfd / clone3 tests
+    - mm: io_uring: allow oom-killer from io_uring_setup
+    - kconfig: let 'shell' return enough output for deep path names
+    - ata: libata-core: Disable TRIM on M88V29
+    - soc: aspeed: lpc-ctrl: Block error printing on probe defer cases
+    - xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create
+    - drm/rockchip: dw_hdmi: Do not leave clock enabled in error case
+    - tracing: Fix tp_printk option related with tp_printk_stop_on_boot
+    - display/amd: decrease message verbosity about watermarks table failure
+    - drm/amd/display: Cap pflip irqs per max otg number
+    - drm/amd/display: fix yellow carp wm clamping
+    - net: usb: qmi_wwan: Add support for Dell DW5829e
+    - net: macb: Align the dma and coherent dma masks
+    - kconfig: fix failing to generate auto.conf
+    - scsi: lpfc: Fix pt2pt NVMe PRLI reject LOGO loop
+    - EDAC: Fix calculation of returned address and next offset in
+      edac_align_ptr()
+    - ucounts: Handle wrapping in is_ucounts_overlimit
+    - ucounts: In set_cred_ucounts assume new->ucounts is non-NULL
+    - ucounts: Base set_cred_ucounts changes on the real user
+    - ucounts: Enforce RLIMIT_NPROC not RLIMIT_NPROC+1
+    - lib/iov_iter: initialize "flags" in new pipe_buffer
+    - rlimit: Fix RLIMIT_NPROC enforcement failure caused by capability calls in
+      set_user
+    - ucounts: Move RLIMIT_NPROC handling after set_user
+    - net: sched: limit TC_ACT_REPEAT loops
+    - dmaengine: sh: rcar-dmac: Check for error num after setting mask
+    - dmaengine: stm32-dmamux: Fix PM disable depth imbalance in
+      stm32_dmamux_probe
+    - dmaengine: sh: rcar-dmac: Check for error num after dma_set_max_seg_size
+    - tests: fix idmapped mount_setattr test
+    - i2c: qcom-cci: don't delete an unregistered adapter
+    - i2c: qcom-cci: don't put a device tree node before i2c_add_adapter()
+    - dmaengine: ptdma: Fix the error handling path in pt_core_init()
+    - copy_process(): Move fd_install() out of sighand->siglock critical section
+    - scsi: qedi: Fix ABBA deadlock in qedi_process_tmf_resp() and
+      qedi_process_cmd_cleanup_resp()
+    - ice: enable parsing IPSEC SPI headers for RSS
+    - i2c: brcmstb: fix support for DSL and CM variants
+    - lockdep: Correct lock_classes index mapping
+    - Linux 5.15.25
+  * Jammy update: v5.15.24 upstream stable release (LP: #1963889)
+    - integrity: check the return value of audit_log_start()
+    - ima: fix reference leak in asymmetric_verify()
+    - ima: Remove ima_policy file before directory
+    - ima: Allow template selection with ima_template[_fmt]= after ima_hash=
+    - ima: Do not print policy rule with inactive LSM labels
+    - mmc: sdhci-of-esdhc: Check for error num after setting mask
+    - mmc: core: Wait for command setting 'Power Off Notification' bit to complete
+    - can: isotp: fix potential CAN frame reception race in isotp_rcv()
+    - can: isotp: fix error path in isotp_sendmsg() to unlock wait queue
+    - net: phy: marvell: Fix RGMII Tx/Rx delays setting in 88e1121-compatible PHYs
+    - net: phy: marvell: Fix MDI-x polarity setting in 88e1118-compatible PHYs
+    - NFS: Fix initialisation of nfs_client cl_flags field
+    - NFSD: Fix NFSv3 SETATTR/CREATE's handling of large file sizes
+    - NFSD: Fix ia_size underflow
+    - NFSD: Clamp WRITE offsets
+    - NFSD: Fix offset type in I/O trace points
+    - NFSD: Fix the behavior of READ near OFFSET_MAX
+    - thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume
+    - thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses
+    - thermal: int340x: Limit Kconfig to 64-bit
+    - thermal/drivers/int340x: Fix RFIM mailbox write commands
+    - tracing: Propagate is_signed to expression
+    - NFS: change nfs_access_get_cached to only report the mask
+    - NFSv4 only print the label when its queried
+    - nfs: nfs4clinet: check the return value of kstrdup()
+    - NFSv4.1: Fix uninitialised variable in devicenotify
+    - NFSv4 remove zero number of fs_locations entries error check
+    - NFSv4 store server support for fs_location attribute
+    - NFSv4.1 query for fs_location attr on a new file system
+    - NFSv4 expose nfs_parse_server_name function
+    - NFSv4 handle port presence in fs_location server string
+    - SUNRPC allow for unspecified transport time in rpc_clnt_add_xprt
+    - net/sunrpc: fix reference count leaks in rpc_sysfs_xprt_state_change
+    - sunrpc: Fix potential race conditions in rpc_sysfs_xprt_state_change()
+    - irqchip/realtek-rtl: Service all pending interrupts
+    - perf/x86/rapl: fix AMD event handling
+    - x86/perf: Avoid warning for Arch LBR without XSAVE
+    - sched: Avoid double preemption in __cond_resched_*lock*()
+    - drm/vc4: Fix deadlock on DSI device attach error
+    - drm: panel-orientation-quirks: Add quirk for the 1Netbook OneXPlayer
+    - net: sched: Clarify error message when qdisc kind is unknown
+    - powerpc/fixmap: Fix VM debug warning on unmap
+    - scsi: target: iscsi: Make sure the np under each tpg is unique
+    - scsi: ufs: ufshcd-pltfrm: Check the return value of devm_kstrdup()
+    - scsi: qedf: Add stag_work to all the vports
+    - scsi: qedf: Fix refcount issue when LOGO is received during TMF
+    - scsi: qedf: Change context reset messages to ratelimited
+    - scsi: pm8001: Fix bogus FW crash for maxcpus=1
+    - scsi: ufs: Use generic error code in ufshcd_set_dev_pwr_mode()
+    - scsi: ufs: Treat link loss as fatal error
+    - scsi: myrs: Fix crash in error case
+    - net: stmmac: reduce unnecessary wakeups from eee sw timer
+    - PM: hibernate: Remove register_nosave_region_late()
+    - drm/amd/display: Correct MPC split policy for DCN301
+    - usb: dwc2: gadget: don't try to disable ep0 in dwc2_hsotg_suspend
+    - perf: Always wake the parent event
+    - nvme-pci: add the IGNORE_DEV_SUBNQN quirk for Intel P4500/P4600 SSDs
+    - MIPS: Fix build error due to PTR used in more places
+    - net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
+    - KVM: eventfd: Fix false positive RCU usage warning
+    - KVM: nVMX: eVMCS: Filter out VM_EXIT_SAVE_VMX_PREEMPTION_TIMER
+    - KVM: nVMX: Also filter MSR_IA32_VMX_TRUE_PINBASED_CTLS when eVMCS
+    - KVM: SVM: Don't kill SEV guest if SMAP erratum triggers in usermode
+    - KVM: VMX: Set vmcs.PENDING_DBG.BS on #DB in STI/MOVSS blocking shadow
+    - KVM: x86: Report deprecated x87 features in supported CPUID
+    - riscv: fix build with binutils 2.38
+    - riscv: cpu-hotplug: clear cpu from numa map when teardown
+    - riscv: eliminate unreliable __builtin_frame_address(1)
+    - gfs2: Fix gfs2_release for non-writers regression
+    - ARM: dts: imx23-evk: Remove MX23_PAD_SSP1_DETECT from hog group
+    - ARM: dts: Fix boot regression on Skomer
+    - ARM: socfpga: fix missing RESET_CONTROLLER
+    - nvme-tcp: fix bogus request completion when failing to send AER
+    - ACPI/IORT: Check node revision for PMCG resources
+    - PM: s2idle: ACPI: Fix wakeup interrupts handling
+    - drm/amdgpu/display: change pipe policy for DCN 2.0
+    - drm/rockchip: vop: Correct RK3399 VOP register fields
+    - drm/i915: Allow !join_mbus cases for adlp+ dbuf configuration
+    - drm/i915: Populate pipe dbuf slices more accurately during readout
+    - ARM: dts: Fix timer regression for beagleboard revision c
+    - ARM: dts: meson: Fix the UART compatible strings
+    - ARM: dts: meson8: Fix the UART device-tree schema validation
+    - ARM: dts: meson8b: Fix the UART device-tree schema validation
+    - phy: broadcom: Kconfig: Fix PHY_BRCM_USB config option
+    - staging: fbtft: Fix error path in fbtft_driver_module_init()
+    - ARM: dts: imx6qdl-udoo: Properly describe the SD card detect
+    - phy: xilinx: zynqmp: Fix bus width setting for SGMII
+    - phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable()
+    - ARM: dts: imx7ulp: Fix 'assigned-clocks-parents' typo
+    - arm64: dts: imx8mq: fix mipi_csi bidirectional port numbers
+    - usb: f_fs: Fix use-after-free for epfile
+    - phy: dphy: Correct clk_pre parameter
+    - gpio: aggregator: Fix calling into sleeping GPIO controllers
+    - NFS: Don't overfill uncached readdir pages
+    - NFS: Don't skip directory entries when doing uncached readdir
+    - drm/vc4: hdmi: Allow DBLCLK modes even if horz timing is odd.
+    - misc: fastrpc: avoid double fput() on failed usercopy
+    - net: sparx5: Fix get_stat64 crash in tcpdump
+    - netfilter: ctnetlink: disable helper autoassign
+    - arm64: dts: meson-g12b-odroid-n2: fix typo 'dio2133'
+    - arm64: dts: meson-sm1-odroid: use correct enable-gpio pin for tf-io
+      regulator
+    - arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO domain for GPIOE_2
+    - arm64: dts: meson-sm1-odroid: fix boot loop after reboot
+    - ixgbevf: Require large buffers for build_skb on 82599VF
+    - drm/panel: simple: Assign data from panel_dpi_probe() correctly
+    - ACPI: PM: s2idle: Cancel wakeup before dispatching EC GPE
+    - gpiolib: Never return internal error codes to user space
+    - gpio: sifive: use the correct register to read output values
+    - fbcon: Avoid 'cap' set but not used warning
+    - bonding: pair enable_port with slave_arr_updates
+    - net: dsa: mv88e6xxx: don't use devres for mdiobus
+    - net: dsa: ar9331: register the mdiobus under devres
+    - net: dsa: bcm_sf2: don't use devres for mdiobus
+    - net: dsa: felix: don't use devres for mdiobus
+    - net: dsa: mt7530: fix kernel bug in mdiobus_free() when unbinding
+    - net: dsa: lantiq_gswip: don't use devres for mdiobus
+    - ipmr,ip6mr: acquire RTNL before calling ip[6]mr_free_table() on failure path
+    - nfp: flower: fix ida_idx not being released
+    - net: do not keep the dst cache when uncloning an skb dst and its metadata
+    - net: fix a memleak when uncloning an skb dst and its metadata
+    - veth: fix races around rq->rx_notify_masked
+    - net: mdio: aspeed: Add missing MODULE_DEVICE_TABLE
+    - tipc: rate limit warning for received illegal binding update
+    - net: amd-xgbe: disable interrupts during pci removal
+    - drm/amd/pm: fix hwmon node of power1_label create issue
+    - mptcp: netlink: process IPv6 addrs in creating listening sockets
+    - dpaa2-eth: unregister the netdev before disconnecting from the PHY
+    - ice: fix an error code in ice_cfg_phy_fec()
+    - ice: fix IPIP and SIT TSO offload
+    - ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
+    - ice: Avoid RTNL lock when re-creating auxiliary device
+    - net: mscc: ocelot: fix mutex lock error during ethtool stats read
+    - net: dsa: mv88e6xxx: fix use-after-free in mv88e6xxx_mdios_unregister
+    - vt_ioctl: fix array_index_nospec in vt_setactivate
+    - vt_ioctl: add array_index_nospec to VT_ACTIVATE
+    - n_tty: wake up poll(POLLRDNORM) on receiving data
+    - eeprom: ee1004: limit i2c reads to I2C_SMBUS_BLOCK_MAX
+    - usb: dwc2: drd: fix soft connect when gadget is unconfigured
+    - Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
+    - net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
+    - usb: ulpi: Move of_node_put to ulpi_dev_release
+    - usb: ulpi: Call of_node_put correctly
+    - usb: dwc3: gadget: Prevent core from processing stale TRBs
+    - usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
+    - USB: gadget: validate interface OS descriptor requests
+    - usb: gadget: rndis: check size of RNDIS_MSG_SET command
+    - usb: gadget: f_uac2: Define specific wTerminalType
+    - usb: raw-gadget: fix handling of dual-direction-capable endpoints
+    - USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
+    - USB: serial: option: add ZTE MF286D modem
+    - USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
+    - USB: serial: cp210x: add NCR Retail IO box id
+    - USB: serial: cp210x: add CPI Bulk Coin Recycler id
+    - speakup-dectlk: Restore pitch setting
+    - phy: ti: Fix missing sentinel for clk_div_table
+    - iio: buffer: Fix file related error handling in IIO_BUFFER_GET_FD_IOCTL
+    - mm: memcg: synchronize objcg lists with a dedicated spinlock
+    - seccomp: Invalidate seccomp mode to catch death failures
+    - signal: HANDLER_EXIT should clear SIGNAL_UNKILLABLE
+    - s390/cio: verify the driver availability for path_event call
+    - bus: mhi: pci_generic: Add mru_default for Foxconn SDX55
+    - bus: mhi: pci_generic: Add mru_default for Cinterion MV31-W
+    - hwmon: (dell-smm) Speed up setting of fan speed
+    - x86/sgx: Silence softlockup detection when releasing large enclaves
+    - Makefile.extrawarn: Move -Wunaligned-access to W=1
+    - scsi: lpfc: Remove NVMe support if kernel has NVME_FC disabled
+    - scsi: lpfc: Reduce log messages seen after firmware download
+    - MIPS: octeon: Fix missed PTR->PTR_WD conversion
+    - arm64: dts: imx8mq: fix lcdif port node
+    - perf: Fix list corruption in perf_cgroup_switch()
+    - iommu: Fix potential use-after-free during probe
+    - Linux 5.15.24
+  * Jammy update: v5.15.23 upstream stable release (LP: #1963888)
+    - moxart: fix potential use-after-free on remove path
+    - arm64: Add Cortex-A510 CPU part definition
+    - ksmbd: fix SMB 3.11 posix extension mount failure
+    - crypto: api - Move cryptomgr soft dependency into algapi
+    - Linux 5.15.23
+  * [22.04 FEAT] KVM: Enable storage key checking for intercepted instruction
+    handled by userspace (LP: #1933179)
+    - KVM: s390: gaccess: Refactor gpa and length calculation
+    - KVM: s390: gaccess: Refactor access address range check
+    - KVM: s390: gaccess: Cleanup access to guest pages
+    - s390/uaccess: introduce bit field for OAC specifier
+    - s390/uaccess: fix compile error
+    - s390/uaccess: Add copy_from/to_user_key functions
+    - KVM: s390: Honor storage keys when accessing guest memory
+    - KVM: s390: handle_tprot: Honor storage keys
+    - KVM: s390: selftests: Test TEST PROTECTION emulation
+    - KVM: s390: Add optional storage key checking to MEMOP IOCTL
+    - KVM: s390: Add vm IOCTL for key checked guest absolute memory access
+    - KVM: s390: Rename existing vcpu memop functions
+    - KVM: s390: Add capability for storage key extension of MEM_OP IOCTL
+    - KVM: s390: Update api documentation for memop ioctl
+    - KVM: s390: Clarify key argument for MEM_OP in api docs
+    - KVM: s390: Add missing vm MEM_OP size check
+  * CVE-2022-25636
+    - netfilter: nf_tables_offload: incorrect flow offload action array size
+  * ubuntu_kernel_selftests / ftrace:ftracetest do_softirq failure on Jammy
+    realtime (LP: #1959610)
+    - selftests/ftrace: Do not trace do_softirq because of PREEMPT_RT
+  * CVE-2022-0435
+    - tipc: improve size validations for received domain records
+  * CVE-2022-0516
+    - KVM: s390: Return error on SIDA memop on normal guest
+  * EDAC update for AMD Genoa support in 22.04 (LP: #1960362)
+    - EDAC: Add RDDR5 and LRDDR5 memory types
+    - EDAC/amd64: Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
+  * hwmon: k10temp updates for AMD Genoa in 22.04 (LP: #1960361)
+    - x86/amd_nb: Add AMD Family 19h Models (10h-1Fh) and (A0h-AFh) PCI IDs
+    - hwmon: (k10temp) Remove unused definitions
+    - hwmon: (k10temp) Support up to 12 CCDs on AMD Family of processors
+    - hwmon: (k10temp) Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
+  * [SRU][I/J/OEM-5.13/OEM-5.14] Add basic support of MT7922 (LP: #1958151)
+    - mt76: mt7921: Add mt7922 support
+    - mt76: mt7921: add support for PCIe ID 0x0608/0x0616
+    - mt76: mt7921: introduce 160 MHz channel bandwidth support
+  * Use EC GPE for s2idle wakeup on AMD platforms (LP: #1960771)
+    - ACPI: PM: Revert "Only mark EC GPE for wakeup on Intel systems"
+  * Update Broadcom Emulex FC HBA lpfc driver to 14.0.0.4 for Ubuntu 22.04
+    (LP: #1956982)
+    - scsi: lpfc: Change return code on I/Os received during link bounce
+    - scsi: lpfc: Fix NPIV port deletion crash
+    - scsi: lpfc: Adjust CMF total bytes and rxmonitor
+    - scsi: lpfc: Cap CMF read bytes to MBPI
+    - scsi: lpfc: Add additional debugfs support for CMF
+    - scsi: lpfc: Update lpfc version to 14.0.0.4
+  * Forward-port drm/i915 commits from oem-5.14 for Alder Lake S & P
+    (LP: #1960298)
+    - drm/i915/dmc: Update to DMC v2.12
+    - drm/i915/adlp/tc: Fix PHY connected check for Thunderbolt mode
+    - drm/i915/tc: Remove waiting for PHY complete during releasing ownership
+    - drm/i915/tc: Check for DP-alt, legacy sinks before taking PHY ownership
+    - drm/i915/tc: Add/use helpers to retrieve TypeC port properties
+    - drm/i915/tc: Don't keep legacy TypeC ports in connected state w/o a sink
+    - drm/i915/tc: Add a mode for the TypeC PHY's disconnected state
+    - drm/i915/tc: Refactor TC-cold block/unblock helpers
+    - drm/i915/tc: Avoid using legacy AUX PW in TBT mode
+    - drm/i915/icl/tc: Remove the ICL special casing during TC-cold blocking
+    - drm/i915/tc: Fix TypeC PHY connect/disconnect logic on ADL-P
+    - drm/i915/tc: Drop extra TC cold blocking from intel_tc_port_connected()
+    - drm/i915/tc: Fix system hang on ADL-P during TypeC PHY disconnect
+    - drm/i915/display/adlp: Disable underrun recovery
+    - drm/i915/adl_s: Remove require_force_probe protection
+    - drm/i915/adlp: Remove require_force_probe protection
+  * INVALID or PRIVATE BUG (LP: #1959735)
+    - KVM: s390: Simplify SIGP Set Arch handling
+    - KVM: s390: Add a routine for setting userspace CPU state
+  * Include the QCA WCN 6856 v2.1 support (LP: #1954938)
+    - SAUCE: ath11k: shrink TCSR read mask for WCN6855 hw2.1
+  * Jammy update: v5.15.22 upstream stable release (LP: #1960516)
+    - drm/i915: Disable DSB usage for now
+    - selinux: fix double free of cond_list on error paths
+    - audit: improve audit queue handling when "audit=1" on cmdline
+    - ipc/sem: do not sleep with a spin lock held
+    - spi: stm32-qspi: Update spi registering
+    - ASoC: hdmi-codec: Fix OOB memory accesses
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_volsw()
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_volsw_sx()
+    - ASoC: ops: Reject out of bounds values in snd_soc_put_xr_sx()
+    - ALSA: usb-audio: Correct quirk for VF0770
+    - ALSA: hda: Fix UAF of leds class devs at unbinding
+    - ALSA: hda: realtek: Fix race at concurrent COEF updates
+    - ALSA: hda/realtek: Add quirk for ASUS GU603
+    - ALSA: hda/realtek: Add missing fixup-model entry for Gigabyte X570 ALC1220
+      quirks
+    - ALSA: hda/realtek: Fix silent output on Gigabyte X570S Aorus Master (newer
+      chipset)
+    - ALSA: hda/realtek: Fix silent output on Gigabyte X570 Aorus Xtreme after
+      reboot from Windows
+    - btrfs: don't start transaction for scrub if the fs is mounted read-only
+    - btrfs: fix deadlock between quota disable and qgroup rescan worker
+    - btrfs: fix use-after-free after failure to create a snapshot
+    - Revert "fs/9p: search open fids first"
+    - drm/nouveau: fix off by one in BIOS boundary checking
+    - drm/i915/adlp: Fix TypeC PHY-ready status readout
+    - drm/amd/pm: correct the MGpuFanBoost support for Beige Goby
+    - drm/amd/display: watermark latencies is not enough on DCN31
+    - drm/amd/display: Force link_rate as LINK_RATE_RBR2 for 2018 15" Apple Retina
+      panels
+    - nvme-fabrics: fix state check in nvmf_ctlr_matches_baseopts()
+    - mm/debug_vm_pgtable: remove pte entry from the page table
+    - mm/pgtable: define pte_index so that preprocessor could recognize it
+    - mm/kmemleak: avoid scanning potential huge holes
+    - block: bio-integrity: Advance seed correctly for larger interval sizes
+    - dma-buf: heaps: Fix potential spectre v1 gadget
+    - IB/hfi1: Fix AIP early init panic
+    - Revert "fbcon: Disable accelerated scrolling"
+    - fbcon: Add option to enable legacy hardware acceleration
+    - mptcp: fix msk traversal in mptcp_nl_cmd_set_flags()
+    - Revert "ASoC: mediatek: Check for error clk pointer"
+    - KVM: arm64: Avoid consuming a stale esr value when SError occur
+    - KVM: arm64: Stop handle_exit() from handling HVC twice when an SError occurs
+    - RDMA/cma: Use correct address when leaving multicast group
+    - RDMA/ucma: Protect mc during concurrent multicast leaves
+    - RDMA/siw: Fix refcounting leak in siw_create_qp()
+    - IB/rdmavt: Validate remote_addr during loopback atomic tests
+    - RDMA/siw: Fix broken RDMA Read Fence/Resume logic.
+    - RDMA/mlx4: Don't continue event handler after memory allocation failure
+    - ALSA: usb-audio: initialize variables that could ignore errors
+    - ALSA: hda: Fix signedness of sscanf() arguments
+    - ALSA: hda: Skip codec shutdown in case the codec is not registered
+    - iommu/vt-d: Fix potential memory leak in intel_setup_irq_remapping()
+    - iommu/amd: Fix loop timeout issue in iommu_ga_log_enable()
+    - spi: bcm-qspi: check for valid cs before applying chip select
+    - spi: mediatek: Avoid NULL pointer crash in interrupt
+    - spi: meson-spicc: add IRQ check in meson_spicc_probe
+    - spi: uniphier: fix reference count leak in uniphier_spi_probe()
+    - IB/hfi1: Fix tstats alloc and dealloc
+    - IB/cm: Release previously acquired reference counter in the cm_id_priv
+    - net: ieee802154: hwsim: Ensure proper channel selection at probe time
+    - net: ieee802154: mcr20a: Fix lifs/sifs periods
+    - net: ieee802154: ca8210: Stop leaking skb's
+    - netfilter: nft_reject_bridge: Fix for missing reply from prerouting
+    - net: ieee802154: Return meaningful error codes from the netlink helpers
+    - net/smc: Forward wakeup to smc socket waitqueue after fallback
+    - net: stmmac: dwmac-visconti: No change to ETHER_CLOCK_SEL for unexpected
+      speed request.
+    - net: stmmac: properly handle with runtime pm in stmmac_dvr_remove()
+    - net: macsec: Fix offload support for NETDEV_UNREGISTER event
+    - net: macsec: Verify that send_sci is on when setting Tx sci explicitly
+    - net: stmmac: dump gmac4 DMA registers correctly
+    - net: stmmac: ensure PTP time register reads are consistent
+    - drm/kmb: Fix for build errors with Warray-bounds
+    - drm/i915/overlay: Prevent divide by zero bugs in scaling
+    - drm/amd: avoid suspend on dGPUs w/ s2idle support when runtime PM enabled
+    - ASoC: fsl: Add missing error handling in pcm030_fabric_probe
+    - ASoC: xilinx: xlnx_formatter_pcm: Make buffer bytes multiple of period bytes
+    - ASoC: simple-card: fix probe failure on platform component
+    - ASoC: cpcap: Check for NULL pointer after calling of_get_child_by_name
+    - ASoC: max9759: fix underflow in speaker_gain_control_put()
+    - ASoC: codecs: wcd938x: fix incorrect used of portid
+    - ASoC: codecs: lpass-rx-macro: fix sidetone register offsets
+    - ASoC: codecs: wcd938x: fix return value of mixer put function
+    - pinctrl: sunxi: Fix H616 I2S3 pin data
+    - pinctrl: intel: Fix a glitch when updating IRQ flags on a preconfigured line
+    - pinctrl: intel: fix unexpected interrupt
+    - pinctrl: bcm2835: Fix a few error paths
+    - scsi: bnx2fc: Make bnx2fc_recv_frame() mp safe
+    - nfsd: nfsd4_setclientid_confirm mistakenly expires confirmed client.
+    - gve: fix the wrong AdminQ buffer queue index check
+    - bpf: Use VM_MAP instead of VM_ALLOC for ringbuf
+    - selftests/exec: Remove pipe from TEST_GEN_FILES
+    - selftests: futex: Use variable MAKE instead of make
+    - tools/resolve_btfids: Do not print any commands when building silently
+    - e1000e: Separate ADP board type from TGP
+    - rtc: cmos: Evaluate century appropriate
+    - kvm: add guest_state_{enter,exit}_irqoff()
+    - kvm/arm64: rework guest entry logic
+    - perf: Copy perf_event_attr::sig_data on modification
+    - perf stat: Fix display of grouped aliased events
+    - perf/x86/intel/pt: Fix crash with stop filters in single-range mode
+    - x86/perf: Default set FREEZE_ON_SMI for all
+    - EDAC/altera: Fix deferred probing
+    - EDAC/xgene: Fix deferred probing
+    - ext4: prevent used blocks from being allocated during fast commit replay
+    - ext4: modify the logic of ext4_mb_new_blocks_simple
+    - ext4: fix error handling in ext4_restore_inline_data()
+    - ext4: fix error handling in ext4_fc_record_modified_inode()
+    - ext4: fix incorrect type issue during replay_del_range
+    - net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY
+    - cgroup/cpuset: Fix "suspicious RCU usage" lockdep warning
+    - tools include UAPI: Sync sound/asound.h copy with the kernel sources
+    - gpio: idt3243x: Fix an ignored error return from platform_get_irq()
+    - gpio: mpc8xxx: Fix an ignored error return from platform_get_irq()
+    - selftests: nft_concat_range: add test for reload with no element add/del
+    - selftests: netfilter: check stateless nat udp checksum fixup
+    - Linux 5.15.22
+    - [Config] disable FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+  * Jammy update: v5.15.21 upstream stable release (LP: #1960515)
+    - Revert "drm/vc4: hdmi: Make sure the device is powered with CEC"
+    - Revert "drm/vc4: hdmi: Make sure the device is powered with CEC" again
+    - Linux 5.15.21
+  * Jammy update: v5.15.20 upstream stable release (LP: #1960509)
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Add handshake with the CSME to
+      support S0ix""
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Add polling mechanism to indicate
+      CSME DPG exit""
+    - Revert "UBUNTU: SAUCE: Revert "e1000e: Additional PHY power saving in S0ix""
+    - PCI: pciehp: Fix infinite loop in IRQ handler upon power fault
+    - selftests: mptcp: fix ipv6 routing setup
+    - net: ipa: use a bitmap for endpoint replenish_enabled
+    - net: ipa: prevent concurrent replenish
+    - drm/vc4: hdmi: Make sure the device is powered with CEC
+    - cgroup-v1: Require capabilities to set release_agent
+    - Revert "mm/gup: small refactoring: simplify try_grab_page()"
+    - ovl: don't fail copy up if no fileattr support on upper
+    - lockd: fix server crash on reboot of client holding lock
+    - lockd: fix failure to cleanup client locks
+    - net/mlx5e: IPsec: Fix tunnel mode crypto offload for non TCP/UDP traffic
+    - net/mlx5: Bridge, take rtnl lock in init error handler
+    - net/mlx5: Bridge, ensure dev_name is null-terminated
+    - net/mlx5e: Fix handling of wrong devices during bond netevent
+    - net/mlx5: Use del_timer_sync in fw reset flow of halting poll
+    - net/mlx5e: Fix module EEPROM query
+    - net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
+    - net/mlx5e: Don't treat small ceil values as unlimited in HTB offload
+    - net/mlx5: Bridge, Fix devlink deadlock on net namespace deletion
+    - net/mlx5: E-Switch, Fix uninitialized variable modact
+    - ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback
+    - i40e: Fix reset bw limit when DCB enabled with 1 TC
+    - i40e: Fix reset path while removing the driver
+    - net: amd-xgbe: ensure to reset the tx_timer_active flag
+    - net: amd-xgbe: Fix skb data length underflow
+    - fanotify: Fix stale file descriptor in copy_event_to_user()
+    - net: sched: fix use-after-free in tc_new_tfilter()
+    - rtnetlink: make sure to refresh master_dev/m_ops in __rtnl_newlink()
+    - cpuset: Fix the bug that subpart_cpus updated wrongly in update_cpumask()
+    - e1000e: Handshake with CSME starts from ADL platforms
+    - af_packet: fix data-race in packet_setsockopt / packet_setsockopt
+    - tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data()
+    - ovl: fix NULL pointer dereference in copy up warning
+    - Linux 5.15.20
+  * Miscellaneous Ubuntu changes
+    - [Packaging] use default zstd compression
+    - [Packaging] do not use compression for image packages
+    - [Packaging] use xz compression for ddebs
+    - [Config] upgrade debug symbols from DWARF4 to DWARF5
+    - SAUCE: Makefile: Remove inclusion of lbm header files
+    - SAUCE: Makefile: Fix compiler warnings
+    - SAUCE: AUFS
+    - SAUCE: aufs: switch to 64-bit ino_t for s390x
+    - [Config] set AUFS as disabled
+    - SAUCE: mt76: mt7921e: fix possible probe failure after reboot
+    - Remove ubuntu/hio driver
+    - SAUCE: ima_policy: fix test for empty rule set
+    - SAUCE: sfc: The size of the RX recycle ring should be more flexible
+    - [Config] MITIGATE_SPECTRE_BRANCH_HISTORY=y && HARDEN_BRANCH_HISTORY=y
+  * Miscellaneous upstream changes
+    - kbuild: Unify options for BTF generation for vmlinux and modules
+    - MAINTAINERS: Add scripts/pahole-flags.sh to BPF section
+    - kbuild: Add CONFIG_PAHOLE_VERSION
+    - scripts/pahole-flags.sh: Use pahole-version.sh
+    - lib/Kconfig.debug: Use CONFIG_PAHOLE_VERSION
+    - lib/Kconfig.debug: Allow BTF + DWARF5 with pahole 1.21+
+    - x86/sched: Decrease further the priorities of SMT siblings
+    - sched/topology: Introduce sched_group::flags
+    - sched/fair: Optimize checking for group_asym_packing
+    - sched/fair: Provide update_sg_lb_stats() with sched domain statistics
+    - sched/fair: Carve out logic to mark a group for asymmetric packing
+    - sched/fair: Consider SMT in ASYM_PACKING load balance
+    - Revert "UBUNTU: [Config] x86-64: SYSFB_SIMPLEFB=y"
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Thu, 21 Apr 2022 17:20:52 +0800
+
+linux-xilinx-zynqmp (5.15.0-1005.6) jammy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs from Analysis_14_APR_2022
+
+  * Miscellaneous upstream changes
+    - net: xilinx: TSN endpoint extension support
+    - dt-bindings: Add EP MCDMA related bindings
+    - net: xilinx: EP only data path change
+    - net: xilinx: Change TADMA from discrete to continuous
+    - net: xilinx: Add barriers to fix bootup, switch cam entry and qci issues
+    - net: xilinx: Add support for dynamic configuration of Layer 2 stream
+      identification
+    - net: xilinx: Simplify device reset sequence
+    - net: xilinx: Pass phy interface to of_phy_connect()
+    - net: xilinx: Fix ep ioctl
+    - net: xilinx: Move Xilinx TSN to staging
+    - xilinx: Add TSN configuration options to kernel defconfig
+    - xilinx: Enable ethernet configs relevant to SOM TSN apps.
+    - misc: xilinx-ai-engine: Null terminate local event sysfs buffer
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Fri, 15 Apr 2022 12:03:29 +0800
+
+linux-xilinx-zynqmp (5.15.0-1004.5) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1966944)
+    - [Config] Disable CONFIG_ASYNC_TX_DMA
+
+  * INVALID or PRIVATE BUG (LP: #1964909)
+    - [Config] Enable Mali kernel driver
+
+  * Miscellaneous upstream changes
+    - Import Mali source code
+    - Change Makefile to be compatible with Yocto
+    - staging: mali: r8p0-01rel0: Add the ZYNQ/ZYNQMP platform
+    - staging: mali: r8p0-01rel0: Remove unused trace macros
+    - staging: mali: r8p0-01rel0: Don't include mali_read_phys() for zynq/zynqmp
+    - linux/mali_kernel_linux.c: Handle clock when probed and removed
+    - arm.c: global variable dma_ops is removed from the kernel 4.7
+    - common/mali_pm.c: Add PM runtime barrier after removing suspend
+    - linux/mali_kernel_linux.c: Enable/disable clock for runtime resume/suspend
+    - linux: mali_memory_os_alloc: Remove __GFP_COLD
+    - linux: mali_memory_secure: Add header file dma-direct.h
+    - linux: mali_*timer: Get rid of init_timer
+    - fix-driver-failed-to-check-map-error
+    - mali_memory_secure: Kernel 5.0 onwards 'access_ok' API does not take 'type'
+      as input parameter
+    - Support for vm_insert_pfn deprecated from kernel 4.20
+    - Change return type to vm_fault_t for fault handler
+    - "get_monotonic_boottime(&ts)" deprecated from kernel 4.20 onwards
+    - Fix ioremap_nocache() deprecation in kernel 5.6
+    - Use updated timekeeping functions in kernel 5.6
+    - Set HAVE_UNLOCKED_IOCTL default to true
+    - Use PTR_ERR_OR_ZERO instead of PTR_RET
+
+  [ Ubuntu: 5.15.0-22.22 ]
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Wed, 13 Apr 2022 16:16:17 +0800
+
+linux-xilinx-zynqmp (5.15.0-1003.4) jammy; urgency=medium
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs from Analysis_29_MAR_200
+
+  * Miscellaneous upstream changes
+    - microblaze: Use simple memmove/memcpy implementation from lib/string.c
+    - microblaze: Do loop unrolling for optimized memset implemenation
+    - microblaze: Wire memblock_dump_all()
+    - microblaze: Add support for reserved memory defined by DT
+    - net: macb: In ZynqMP initialization make SGMII phy configuration optional
+    - drm: xlnx: sdi: Add extra check to get the correct timing table index
+    - net: xilinx: axiethernet: Change the link up sequence from Block lock to Rx
+      status and valid Rx code.
+    - v4l: xilinx: dprx: Add unplug handler function in work queue
+    - arm64: zynqmp: Add PHY description for SGMII on vck190 SC
+    - dt-bindings: display: xlnx: extract zynqmp dpaud setting to separate binding
+    - arm64: xilinx: dts: Move DP audio registers to separate node
+    - sound: soc: xilinx: Added 44.1k & 48k sample rate support for DP
+    - Revert "ARM: zynq: Fix nand partitions for zc770-xm011"
+    - misc: xilinx-ai-engine: log additional hardware info
+    - dma: xlnx: drv: Added failsafe code for mem2mem DMA channels init-deinit
+    - xlnx: drv: m2m: Fix SPDX license coding style
+    - mtd: spi-nor: Avoid updating the flash_info struct in dual and stacked modes
+    - media: v4l: Support 3 planar YUV444P 8bpc pixel format in contiguous memory
+    - v4l: xilinx: vip: Support for 3 planar YUV444 8bpc format in contiguous
+      memory
+    - dt-bindings: dma: xilinx_frmbuf: Add support for 3 planar YUV444P 8bpc
+    - dmaengine: xilinx: frmbuf: Add support for 3 planar YUV444P 8bpc
+    - media: v4l2-tpg: add support for new pixelformat V4L2_PIX_FMT_YUV444P
+    - dt-bindings: xilinx: Fix issues with dprxss dt binding yaml
+    - xilinx: Enabled framebuffer configurations in default configuration
+    - media: i2c: ap1302: Update the min values for ap1302 controls
+    - dt-bindings: remoteproc: Update lockstep/split R5 configuration values
+    - net: axienet: Fix warnings related to function prototype
+    - net: axienet: Fix missing kernel description warnings
+    - net: axienet: Add coding style related fixes
+    - net: macb: Fix lost RX packet wakeup race in NAPI receive
+    - clk: xilinx: vcu: don't set pll_ref as parent of VCU(enc/dec) clocks
+    - pwm: pwm-cadence: Handle pwm-cells through of_xlate
+    - dt-bindings: timer: Update pwm-cells value ranges
+    - drm: xlnx: dptx: Add audio codec driver support
+    - sound: soc: xilinx: Remove using hdmi_codec_driver
+    - dt-bindings: misc: xlnx_dpu: Add DPUCZDX8G v3.4 documentation
+    - misc: xlnx_dpu: Add Xilinx DPU IP driver for Vivado tool flow
+    - misc: xlnx_dpu: add helper function to dump all registers
+    - misc: xlnx_dpu: Add debugfs interface to export memory and regs
+    - lib/iov_iter: initialize "flags" in new pipe_buffer
+    - tipc: improve size validations for received domain records
+    - drm: xlnx: hdmi: Get maximum link rate and number of lanes supported by sink
+    - drm: xlnx: hdmi: Correct DDC write field logic
+    - drm: xlnx: hdmi: Update pixel max rate to support higher resolutions
+    - ASoC: xlnx: Remove unnecessary dependency
+    - drm: xlnx: Update DPTX kconfig setting
+    - spi: spi-cadence-quadspi: Fix ospi resume failures
+    - fpga: select FPGA_BRIDGE for 'Xilinx LogiCORE PR Decoupler' helper
+    - dt-bindings: can: xilinx_can: Convert Xilinx CAN binding to YAML
+    - dt: bindings: media: xilinx: Add device tree bindings for subset conv
+    - v4l: xilinx: axis-subsetconv: Add driver for axis subset converter
+    - arm64: xilinx: Enable Xilinx axi4s subset converter driver
+    - arm64: xilinx: Enable IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+    - arm64: xilinx: Enable PWM support
+    - arm64: versal: Enable SND drivers by default for versal
+    - drm: xlnx: Move SND_PCM_ELD selection under DRM_XLNX
+    - drm: xlnx: Update DSI-Tx Kconfig
+    - staging: uartlite-rs485: Initial commit to add drv
+    - staging: uartlite-rs485: Advertise RS485 CAP
+    - arm64: xilinx: Enable Uartlite Rs485
+    - misc: xilinx-ai-engine: Query AIE clock by name ID
+    - misc: xilinx-ai-engine: Fix clock frequency to QoS conversion
+    - can: xilinx_can: Add Transmitter delay compensation (TDC) feature support
+    - microblaze: Remove user exception calling
+    - drivers: misc: xilinx_tmr_manager.c: Add api for reset handler
+    - microblaze: add support for TMR MB manager recovery
+    - edac: xilinx: make event manager registration configurable
+    - mmc: sdhci-of-arasan: Fix SDx_BASECLK configuration issue
+    - mmc: sdhci-of-arasan: Add delay to reach card stable state
+    - drivers: soc: xilinx: Fix error message on SGI registration failure
+    - misc: xilinx-ai-engine: fix return for overlay use case
+    - sound: soc: xilinx: Correct channel status register value for 48k sampled
+      audio
+    - arm64: defconfig: Update kernel configuration to support dma-buf heaps
+    - dmaengine: xilinx: ps_pcie: Remove ZynqMP PS-PCIe End Point Driver
+    - firmware: xilinx: Used lower_32_bits and upper_32_bits
+    - crypto: xilinx: Add upstreamed SHA driver
+    - arm64: xilinx: Enable ARM_PMU by default
+    - net: macb: Add ethtool support to advertise WOL
+    - net: macb: Use pm_runtime_force_resume/suspend APIs in MDIO helper functions
+    - arm64: configs: xilinx: Enable PWM support
+    - Revert "net: macb: Use pm_runtime_force_resume/suspend APIs in MDIO helper
+      functions"
+    - dmaengine: xilinx: frmbuf: Corrected error checking condition in fid_err and
+      fid_out getter functions
+    - arm64: zynqmp: Comment sata phy setting for zcu102
+    - arm64: zynqmp: Add pwm-fan node and fix ttc0 pwm-cells property
+    - arm64: zynqmp: Add pwm-fan node and ttc0 pwm-cells property
+    - arm64: versal: Add support for sysmon SSIT
+    - arm64: versal: Update USB node handle from dwc3 to usb
+    - drivers: crypto: Return error code if data size is out of bounds
+    - arm64: zynqmp: Add power domain description for PL
+    - arm64: zynqmp: Add dmas, gpu, rtc, watchdogs and opp nodes for SOM
+    - net: xilinx: Correct register write values for cam read/write
+    - net: xilinx: Fix HW hang issue for accesses to KEY2 and TV1 registers
+    - net: xilinx: Add switch learning support in TSN driver
+    - net: xilinx: Add switch port state change support
+    - net: xilinx: Add port vlan membership support in PL TSN driver
+    - net: xilinx: Add per vlan HW learning support
+    - net: xilinx: Add native vlan support in PL TSN driver
+    - net: xilinx: Add support to read switch CAM entries
+    - net: xilinx: Change the name of cam add/del function
+    - net: xilinx: Enable ipv when qci isn't enabled.
+    - net: xilinx: Add support for tag/untag options in switch cam
+    - net: xilinx: Set default pcp value for egress queue 1
+    - dt-bindings: Add TADMA specific properties
+    - net: xilinx: Add TADMA driver support
+    - net: xilinx: Add a separate function to set mac address for ep
+    - net: xilinx: Access qbv registers only when Qbv is enabled
+    - net: xilinx: Free the reference to ep, when register_netdevice fails
+    - net: xilinx: Add switch device support
+    - dt-bindings: xilinx_tsn_switch: Document number of ports
+    - net: xilinx: Add default cam entries for Management queue
+    - net: xilinx: Change irq name with details
+    - net: xilinx: Modify CB and QCI ioctl api
+    - net: xilinx: TSN queue numbers
+    - net: xilinx: Add PTPv2 support
+    - net: xilinx: Add support for enabling preemption
+    - net: xilinx: Compile time pcp mapping
+    - net: xilinx: Add check for minimum number of MCDMA Rx queues
+    - dt-bindings: net: Add Xilinx TSN extended endpoint bindings
+    - USB: gadget: validate endpoint index for xilinx udc
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Wed, 06 Apr 2022 22:43:53 +0800
+
+linux-xilinx-zynqmp (5.15.0-1002.3) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1964056)
+    - [Config] Update configs
+
+  * Miscellaneous upstream changes
+    - mtd: tests: Fix eraseblock read speed miscalculation for lower partition
+      sizes
+    - net: axienet: Fix DMA memory error handling during initialization
+    - net: axienet: Handle dma mapping errors in TX datapath
+    - net: axienet: Handle dma mapping errors in RX datapath
+    - spi: spi-zynqmp-gqspi: direct read made word aligned
+    - drm: xlnx: pl_disp: Add condition check for VTC bridge
+    - spi: spi-zynqmp-gqspi: Update driver dependencies
+    - spi: spi-zynq-qspi: Add spi-mem to driver dependencies
+    - mtd: spi-nor: Enable 4byte opcode for Winbond w25h02jvt flash
+    - firmware: xilinx: fix build warnings
+    - v4l: xilinx: hdmirx: Fix reference clock based on TMDS clock ratio
+    - v4l: xilinx: hdmirx: Fix incorrect framerate size for pixel repeat cases
+    - firmware: xilinx: fix backward compatibility
+    - misc: xilinx-ai-engine: release lock before return
+    - misc: xilinx-ai-engine: add dev_gen description
+    - misc: xilinx-ai-engine: balance braces
+    - drm: xlnx: zynqmp_dpsub: Add 3 planar YUV444 10bpc format in contiguous
+      memory
+    - media: v4l: Support 3 planar YUV 444 10bpc pixel format in contiguous memory
+    - v4l: xilinx: vip: Support for 3 planar YUV444 10bpc format in contiguous
+      memory
+    - dmaengine: xilinx: Handle IRQ mapping errors
+    - dt-bindings: dma: xilinx_frmbuf: Add support for 3 planar YUV444 10bpc
+    - dmaengine: xilinx: frmbuf: Add support for 3 planar YUV444 10bpc
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Tue, 08 Mar 2022 14:42:09 +0800
+
+linux-xilinx-zynqmp (5.15.0-1001.2) jammy; urgency=medium
+
+  * INVALID or PRIVATE BUG (LP: #1960990)
+    - [Config] Update configs
+
+  * Miscellaneous Ubuntu changes
+    - [Packaging] use a private PPA for getabis
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Mon, 07 Mar 2022 20:26:07 +0800
+
+linux-xilinx-zynqmp (5.15.0-1000.1) jammy; urgency=medium
+
+  * Packaging resync (LP: #1786013)
+    - [Packaging] update variants
+    - [Packaging] update Ubuntu.md
+    - [Packaging] update update.conf
+
+  * Miscellaneous Ubuntu changes
+    - [Config] Update configs
+
+  * Miscellaneous upstream changes
+    - Add package
+    - firmware: xilinx: add register notifier in zynqmp firmware
+    - firmware: xilinx: export the feature check of zynqmp firmware
+    - firmware: xilinx: move supported api callback ids
+    - include: linux: firmware: Add header file with error events details
+    - drivers: soc: xilinx: add xilinx event management driver
+    - firmware: xilinx: instantiate xilinx event manager driver
+    - driver: soc: xilinx: register for power events in zynqmp power driver
+    - firmware: xilinx: Add shutdown/wakeup APIs
+    - firmware: xilinx: check return value of zynqmp_pm_get_api_version()
+    - firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration.
+    - firmware: xilinx: Add IOCTL support for AIE ISR Clear
+    - firmware: xilinx: provides support to access efuse
+    - firmware: xilinx: Added pm api functions for RSA and SHA
+    - firmware: xilinx: Adds new eemi call for reg access
+    - firmware: xilinx: Enable PM_IOCTL in debugfs
+    - firmware: xilinx: Add missing debug firmware interfaces
+    - firmware: xilinx: Add pm api function for PL readback
+    - firmware: xilinx: Add AFI ioctl support
+    - firmware: xilinx: Add ULPI reset support
+    - firmware: xilinx: Add zynqmp SGMII firmware support
+    - firmware: xilinx: Add qspi firmware interface
+    - firmware: xilinx: xilinx: Add IOCTL ids for probe counter
+    - firmware: xilinx: Add IOCTL for handling usb power requests
+    - firmware: xilinx: Add support for GET_LAST_RESET_REASON IOCTL
+    - xilinx: firmware: Add sysfs to get last reset reason
+    - firmware: xilinx: Use u32 for reset ID in reset APIs
+    - firmware: zynqmp: Use DEVICE_ATTR_* to create sysfs entry
+    - usb: dwc3: Add power management support in DWC3 Xilinx driver
+    - firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
+    - firmware: xilinx: Open MMIO read/write interface via debugfs
+    - firmware: xilinx: Add support for runtime features
+    - firmware: xilinx: Add sysfs support for feature config
+    - firmware: xilinx: Add support to get the image uid info
+    - firmware: xilinx: Add support to access BBRAM and volatile user keys
+    - firmware: xilinx: Update firmware call interface to support additional arg
+    - xilinx: Fix alignment issues
+    - firmware: xilinx: Add support for secure read/write ioctl interface
+    - firmware: xilinx: add support for sd/usb/gem config
+    - firmware: xilinx: Add OSPI Mux selection support
+    - phy: xilinx: zynqmp: Fix bus width setting for SGMII
+    - mtd: rawnand: Add jedec_id to struct onfi_params
+    - mtd: rawnand: pl353: Set the nand chip node as the flash node
+    - dt-bindings: gpio: Add gpio-slg7xl45106.yaml
+    - drivers: gpio: Add support for SLG7XL45106 I2C GPO expander
+    - microblaze: Use simple memset implemenation from lib/string.c
+    - clocksource: timer-cadence-ttc: Do not probe TTC device configured as PWM
+    - dt-bindings: timer: Update device tree bindings for cadence TTC PWM
+    - pwm: pwm-cadence: Add support for TTC PWM
+    - xen/pvcalls: frontend enable
+    - xen/pvcalls: change CONFIG_XEN_PVCALLS_FRONTEND to bool
+    - drivers: soc: xilinx: Call InitFinalize from late_initcall_sync instead of
+      probe
+    - net: macb: add support for mdio phy nodes
+    - dt-bindings: net: macb: update for partial store and forward
+    - net: macb: Add support for partial store and forward
+    - net: macb: PTP fixes
+    - net: macb: Add provision for queue tie off
+    - net: macb: Use WOL via ARP
+    - net: macb: Increment rx bd head after allocating skb and buffer
+    - net: macb: Process tx timestamp only on ptp packets
+    - net: macb: Disable macb pad and fcs for fragmented packets
+    - net: macb: Optimize reading HW timestamp
+    - dt-bindings: net: macb: Add GEM versal compatible string
+    - net: macb: Update tsu clk usage in runtime suspend/resume for Versal
+    - net: macb: Use queue disable instead of tieoff in Versal suspend
+    - net: macb: Increase halt timeout to accommodate 10Mbps link
+    - net: macb: Reset TX when TX halt times out
+    - net: macb: Reorder probe and fix exit path
+    - net: macb: Handle phy reset for PCS PMA IP
+    - net: macb: Align the dma and coherent dma masks
+    - net: macb: Kernel gives call trace during resume from Wake on Lan
+    - net: macb: Handle phy reset for PCS PMA IP
+    - net: macb: Move the phy re-init to phylink function instead of open
+    - dt-bindings: spi: cadence-quadspi: Add support for Xilinx Versal OSPI
+    - spi: cadence-quadspi: Add OSPI support for Xilinx Versal SoC
+    - spi: cadence-quadspi: Add Xilinx Versal external DMA support
+    - spi: cadence-quadspi: fix dma_unmap_single() call
+    - firmware: xilinx: Add tristate configurations
+    - spi: spi-cadence-quadspi: Add support for OSPI device reset
+    - spi: spi-cadence-quadspi: Add support for DDR PHY mode
+    - spi: spi-cadence-quadspi: Add support for odd byte count read/write in DDR
+      mode
+    - mtd: spi-nor: issi: Add support for is25wx256
+    - mtd: spi-nor: gigadevice: Add support for GD25LX256E
+    - mtd: spi-nor: micron-st: Add support for mt35xu01g flash
+    - spi: spi-cadence-quadspi: Add support for OSPI Macronix
+    - spi: spi-cadence-quadspi: Add Rx periodic Tuning support
+    - OF: DT-Overlay configfs interface (v8)
+    - OF: overlay: Perform RCU callback barrier before releasing overlay memory
+      resources
+    - fpga: Add firmware store function
+    - fpga: mgr: Adopted Encrypted BitStream loading support for Xilinx zynqmp
+    - fpga: fpga-mgr: Add readback support
+    - fpga: zynqmp-fpga: Add support for pl configuration readback
+    - fpga: mgr: Update the status for fpga-manager
+    - fpga: zynqmp-fpga: Adds status interface
+    - fpga: Adopted Authenticated BitStream loading support for Xilinx
+    - fpga: doc: Add binding doc for the afi config driver
+    - fpga: Add xilinx AFI config driver
+    - fpga: doc: Add binding doc for the afi config driver
+    - fpga: zynq: Add AFI config driver
+    - fpga: fpga-bridge: Add manual set option via sysfs
+    - fpga: support loading from a pre-allocated buffer
+    - fpga: add bindings document for secure flags
+    - fpga: mgr: Adds secure BitStream loading support
+    - fpga: versal: Use the scatterlist interface
+    - fpga: zynqmp: Use the scatterlist interface
+    - fpga: zynq: Fix incorrect variable type
+    - fpga: zynqmp: Initialized variables before using it
+    - fpga: region: Add fpga-region property 'power-domains'
+    - fpga: region: Adds runtime PM support
+    - fpga: mgr: Update the state to provide the exact error code
+    - fpga: fpga-mgr: fix for coding style issues
+    - fpga: fpga-mgr: Add missing kernel-doc description
+    - fpga: versal: Use tab instead of spaces for indentation
+    - firmware: xilinx: Update the zynqmp_pm_fpga_load() API
+    - firmware: xilinx: Add support to get the image meta-header info
+    - firmware: xilinx: Add TF_A_PM_REGISTER_SGI SMC call
+    - firmware: xilinx: Add IOCTL support for the AIE run time operations
+    - firmware: xilinx: Implemented pm API functions to get the xilfpga component
+      info
+    - firmware: xilinx: Add IOCTL support to query QoS
+    - firmware: zynqmp: Add support for secure_image
+    - firmware: xilinx: Add support for IOCTL and QUERY ID feature check
+    - firmware: xilinx: add new function for do_feature_check_call
+    - firmware: xilinx: always check API version for IOCTL/QUERY
+    - firmware: xilinx: Use proper indentation in kernel-doc
+    - fpga: zynqmp: Add feature-list validation check
+    - dt-bindings: Add dt bindings for flex noc Performance Monitor
+    - misc: xilinx_flex: Add support for the flex noc Performance Monitor
+    - Documentation: short descriptions for Flexnoc Performance Monitor driver
+    - dt-bindings: misc: Add dt bindings for traffic generator
+    - trafgen: xilinx: add axi traffic generator driver
+    - trafgen: Document sysfs entries
+    - i2c: cadence: Recover bus after controller reset
+    - i2c-cadence: Check the return value of pin-ctrl
+    - i2c: cadence: Handling Slave monitor mode
+    - dt-bindings: add documentation of xilinx clocking wizard
+    - clk: clocking-wizard: Add the clockwizard to clk directory
+    - clk: clocking-wizard: Rename nr-outputs to xlnx,nr-outputs
+    - clk: clocking-wizard: Fix the reconfig for 5.2
+    - clk: clocking-wizard: Update the compatible
+    - clocking-wizard: Support higher frequency accuracy
+    - clk: clocking-wizard: Fix coding style violations
+    - dt-binding: apm: Add the binding document for APM
+    - uio: uio_xilinx_apm: Add Xilinx AXI performance monitor driver
+    - clk: zynq: pll: Fix kernel-doc warnings
+    - clk: zynq: trivial warning fix
+    - clk: zynq: Update the parameters to zynq_clk_register_periph_clk
+    - arm: zynq: Suspend support
+    - rtc: zynqmp: Add calibration set and get support
+    - rtc: zynqmp: fix linking failure for ARCH arm
+    - i2c: xiic: Fix Tx Interrupt path for grouped messages
+    - i2c: xiic: Add standard mode support for > 255 byte read transfers
+    - i2c: xiic: Fix coding style issues
+    - i2c: xiic: Enter standard mode only for > 255 byte read transfers
+    - i2c: xiic: Correct the datatype for rx_watermark
+    - i2c: xiic: Fix Rx and Tx paths in standard mode repeated start
+    - i2c: xiic: Add wait for FIFO empty in send_tx
+    - i2c: xiic: Use 'nmsgs' variable instead of repeated_start
+    - i2c: xiic: Add smbus_block_read functionality
+    - i2c-xiic: return value of xiic_reinit
+    - i2c-xiic: Fix the type check for xiic_wakeup
+    - i2c: xiic: Switch to Xiic standard mode for i2c-read
+    - i2c: xiic: Remove interrupt enable/disable in Rx path
+    - i2c: xiic: Update compatible with new IP version
+    - i2c: xiic: Add SCL frequency configuration support
+    - dt-bindings: i2c: xiic: Add 'xlnx,axi-iic-2.1' to compatible
+    - dt-bindings: i2c: xiic: Add 'clock-frequency' property
+    - i2c: xiic: Correct the BNB interrupt enable sequence
+    - dt-bindings: edac: Add bindings for Xilinx ZynqMP OCM binding
+    - edac: zynqmp: Add EDAC support for ZynqMP OCM Controller
+    - serial-uartlite: Remove an un-necessary read of control register
+    - dmaengine: xilinx_dma: Fix kernel-doc warnings
+    - dmaengine: xilinx_dma: Implement error handling in xilinx_dma_child_probe()
+      API
+    - dt-bindings: dmaengine: Add binding for xilinx axidma test client
+    - dmaengine: xilinx: Add axidmatest test client code
+    - dt-bindings: dmaengine: Add binding for vdmatest client
+    - dmaengine: xilinx: Add vdmatest test client code
+    - dma: zynqmp_dma: Initialize descriptor list after freeing during reset
+    - dmaengine: zynqmp_dma: Typecast the variable to handle overflow
+    - dmaengine: zynqmp_dma: Typecast the variable with dma_addr_t to handle
+      overflow
+    - dmaengine: zynqmp_dma: Typecast with enum to fix the coverity warning
+    - dmaengine: zynqmp_dma: Add conditions for return value check
+    - microblaze: timer: Don't use cpu timer setting
+    - microblaze: timer: Separate clocksource timer from clockevent one
+    - microblaze: timer: Pass timer freq via parameter
+    - microblaze: timer: Squash clocksource code together
+    - microblaze: timer: Covert timer to use cpu hotplug
+    - microblaze: timer: Move irq code to clockevent function
+    - microblaze: timer: Create per cpu clockevent device
+    - microblaze: timer: Remove global variables
+    - microblaze: timer: Make sure that clockevent timer is initialized properly
+    - microblaze: timer: Group clockevent setting together
+    - microblaze: timer: Detect cpu_id from DT
+    - microblaze: timer: Change timer initialization setting
+    - microblaze: timer: Make timer SMP aware
+    - microblaze: timer: Add condition to check return value
+    - microblaze: timer: Fix incompatible parameters passed to the function
+    - dt-bindings: net: Add bindings documentation for Xilinx PCS/PMA PHY
+    - net: phy: Add support for xilinx SGMII and 1000BASE-X phys
+    - net: xilinx_phy: Add flag to reset after clock enable
+    - dt-bindings: net: Add binding documentation for axi emaclite
+    - net: emaclite: Fix coding style
+    - net: emaclite: Add variable and conditions to check the return value
+    - net: emaclite: Remove custom BUFFER_ALIGN macro
+    - net: emaclite: Remove advertising of 1G speed and auto negotiation
+    - xilinx: Update copyright text to correct format
+    - Revert "net: axienet: document axistream-connected attribute"
+    - dt-bindings: net: axienet: Add binding for 2.5G, 10G and usxgmii mac
+      variants
+    - dt-bindings: net: axienet: Update binding doc for 10G/25G MAC 1588
+    - dt-bindings: net: axienet: Add clock support
+    - dt-bindings: net: axienet: Add support for mcdma
+    - dt-bindings: Add devicetree documentation for TSN
+    - dt-bindings: Add devicetree documentation for ep
+    - dt-bindings: net: Add devicetree documentation for MRMAC
+    - Revert "net: axienet: make use of axistream-connected attribute optional"
+    - net: axienet: Add NAPI support
+    - net: axienet: Use barriers at relevant places
+    - net: axienet: Fix lost wake-up scenario in xmit
+    - net: axienet: Add support for non-processor mode
+    - net: axienet: Add support for config structure
+    - net: axienet: Add support for 2.5G MAC
+    - net: axienet: Add support for 10G MAC
+    - net: axienet: Add support for 10G/25G MAC
+    - net: axienet: Add support for 1588
+    - net: axienet: Add support for ZynqMP
+    - net: axienet: Adding highmem support
+    - net: axienet: Remove unnecessary phy defines
+    - net: axienet: Allow unaligned transfers
+    - net: axienet: Use ether_addr_copy()
+    - net: axienet: Fix coding style issues
+    - net: axienet: Fix issues when DRE is not enabled in the h/w
+    - net: axienet: Add clock support
+    - net: axienet: added multichannel DMA support
+    - net: xilinx: axiethernet: Add USXGMII support
+    - net: xilinx: axiethernet: Check for queue full in transmit path
+    - net: xilinx: axiethernet: Fix axiethernet register description
+    - net: xilinx: axiethernet: Fix crash in axienet_recv
+    - Revert "net: axienet: convert to phylink API"
+    - net: xilinx: Add support for PL TSN IP features
+    - net: xilinx: Add support for PL TSN endpoint interface
+    - net: xilinx: Add Qci support to the PL TSN IP driver
+    - net: xilinx: Add Support for CB/FRER feature of PL TSN IP
+    - net: xilinx: Add support for Qbu/br feature of PL TSN IP
+    - net: xilinx: axiethernet: Fix swiotlb buffer full error
+    - net: xilinx: axiethernet: Pass phy interface to of_phy_connect()
+    - net: xilinx: Use prandom with range to avoid corner cases
+    - net: xilinx: XXV Ethernet HW timestamp fixes
+    - net: xilinx: Add MRMAC support
+    - net: xilinx: Add HW timestamping support for MRMAC
+    - net: xilinx: Add missing kernel-doc descriptions
+    - net: xilinx: Fix indentation issues
+    - net: xilinx: axiethernet: Add check for transmit data FIFO vacancy
+    - net: xilinx: Check if dma_map_single returned a valid address.
+    - net: xilinx: Refactor TSN functions into xilinx_tsn_ip.c
+    - net: xilinx: Add a separate mcdma probe function for TSN IP
+    - net: xilinx: Add a master xmit function for TSN packets.
+    - net: xilinx: Add MCDMA management channel support
+    - net: xilinx: Access qdv address and associated properties separately
+    - net: xilinx: Cleanup xilinx_tsn_shaper.* files
+    - net: xilinx: axiethernet: Remove the NULL assigning to a pointer
+    - net: xilinx: axiethernet: Fix the use of uninitialized variable
+    - net: xilinx: axiethernet: Add check to overcome NULL dereference warning
+    - net: xilinx: axiethernet: Fix indentation warnings
+    - net: xilinx: axiethernet: Replace the value with enum
+    - net: xilinx: axiethernet: Add condition to check the return value
+    - net: xilinx: axiethernet: Add variables and conditions to check return value
+    - net: xilinx: axiethernet: Reduce the width of variable to handle overflow
+    - net: xilinx: axiethernet: Enable dynamic MDIO MDC
+    - net: xilinx: GT reset updates for 2020.2
+    - net: xilinx: Add supported_coalesce_params to fix axienet on 5.10
+    - net: xilinx: Update MRMAC config structure with PTP command length
+    - net: xilinx: Handle TX TS FIFO timeout error
+    - net: xilinx: MRMAC TX CMD FIFO update
+    - net: xilinx: Add one step 1588 support for MRMAC
+    - net: axienet: Add one step PDelay support
+    - net: axienet: MRMAC reset sequence fixes
+    - net: xilinx: axiethernet: Fix compilation error when HW timestamp is enabled
+    - net: xilinx: Ethtool statistics support
+    - net: xilinx: axiethernet: Correct phy-mode comparison logic in _probe()
+    - net: xilinx: In MCMDA designs fix crash on ifconfig up
+    - net: xilinx: fix compile warning due to typecheck
+    - net: xilinx: axiethernet: Pass correct phy interface to of_phy_connect()
+    - net: axienet: Add GT reset status check for XXV new IP version
+    - dt-bindings: nvmem: Added efuse nodes
+    - nvmem: zynqmp: Added support to access efuse
+    - nvmem: zynqmp: Removed \r format specifier for prints.
+    - nvmem: zynqmp: Add support to PUF eFuses programming for User data
+    - nvmem: zynqmp: Replace ENOTSUPP by EOPNOTSUPP
+    - nvmem: zynqmp-nvmem: Fix passing incompatible parameters
+    - nvmem: zynqmp_nvmem: Fix zynqmp_nvmem_read() parameter alignment
+    - dt-bindings: Convert Xilinx watchdog bindings to json-schema
+    - watchdog: of_xilinx_wdt: Initialize watchdog via data structure
+    - watchdog: of_xilinx_wdt: Introduce wdttype enum for identification
+    - watchdog: of_xilinx_wdt: Add Versal support
+    - watchdog: of_xilinx_wdt: Wire setting up timeout via module parameter/DT
+    - watchdog: of_xilinx_wdt: Use a proper variable to handle overflow
+    - watchdog: of_xilinx_wdt: Add Versal Window watchdog support
+    - dt-bindings: serial: pl011: Add 'arm,xlnx-uart'
+    - serial: pl011: Add support for Xilinx Uart
+    - pinctrl: zynq: use module_platform_driver to simplify the code
+    - can: xilinx_can: Add check for NAPI Poll function
+    - can: xilinx_can: Remove repeated work the from kernel-doc
+    - clk: zynqmp: Add a check for NULL pointer
+    - clk: zynqmp: make bestdiv unsigned
+    - clk: zynqmp: Fix stack-out-of-bounds in strncpy`
+    - xilinx: Update copyright text to correct format
+    - tty: xilinx_uartps: Check the clk_enable return value
+    - tty: xilinx_uartps: Add check for runtime_get_sync calls
+    - tty: xilinx_uartps: Check clk_enable return type
+    - tty: xilinx_uartps: Make the timeout unsigned
+    - serial: uartps: Change uart ID port allocation
+    - serial: uartps: Fix the ignore_status
+    - serial: uartps: Prevent writes when the controller is disabled
+    - serial: uartps: Fix stuck ISR if RX disabled with non-empty FIFO
+    - PCI: xilinx-nwl: Fix coding style violations
+    - PCI: XDMA PL PCIe: Adding device tree binding for XDMA PL PCIe
+    - PCI: XDMA PL PCIe: Adding XDMA PL PCIe Root Port
+    - dt-bindings: irqchip: Add Xilinx Interrupt Controller bindings
+    - irqchip: xilinx: Make per cpu primary controller entries
+    - irqchip: xilinx: Enable generic irq multi handler
+    - irqchip: xilinx: Use handle_domain_irq()
+    - irqchip: xilinx: Move early initialization to own function
+    - irqchip: xilinx: Add support for sw interrupts
+    - irqchip: xilinx: Support only LE/BE irqc by the same driver
+    - irqchip: xilinx: Rename root_domain just to domain
+    - irqchip: xilinx: Add support for cpu hotplug
+    - irqchip: xilinx: Add support for Microblaze SMP
+    - irqchip: xilinx: Change level for cpu-id warning
+    - irqchip: xilinx: Avoid __init macro usage for xilinx_intc_of_init
+    - irqchip: xilinx: Add support to remove Xilinx INTC irqchip driver module
+    - irqchip: xilinx: Add support to remove the Xilinx INTC driver module
+    - synopsys: edac: Fix the issue in reporting of the error count
+    - dt-bindings: usb: Add clock support for udc-xilinx
+    - dt-bindings: udc-xilinx: Fix coding style in binding doc
+    - usb: gadget: udc-xilinx: Add clock support
+    - usb: xilinx: Add suspend resume support
+    - usb: phy: Add platform driver support for ULPI phys
+    - usb: gadget: udc: udc-xilinx: Add identifier to read_fn function arg
+    - usb: host: ehci-xilinx: modified driver to resolve formatting warnings
+    - usb: host: ehci-xilinx: Resolve kernel-doc Warnings
+    - usb: host: xhci: plat: add support for otg_set_host() call
+    - usb: host: xhci: add support for Light Reset for DWC3 DRD
+    - usb: xhci: Add workaround for fixing ep stream ring hang issue
+    - usb: uas: Add workaround for DATA IN urb's returned with status -EAGAIN
+    - uas: Add US_FL_NO_ATA_1X for linux tcm_usb_gadget
+    - usb: gadget: f_tcm: adjust write length with max packet size
+    - usb: gadget: f_tcm: comp_descriptor workaround during SS gadget
+    - usb: gadget: f_tcm: queue multiple commands request
+    - usb: gadget: f_tcm: add TARGET_SCF_ACK_KREF flag in BOT
+    - usb: gadget: f_tcm: support to set maxburst through configfs
+    - usb: function: f_tcm: Add support for getting alt interface number
+    - usb: xhci-plat: Add remote wakeup support
+    - usb: gadget: uvc_video: unlock before submitting a request to ep
+    - usb: xhci: wait for atleast 1ms after exiting U3
+    - usb: host: xhci: Add xhci_hcd to xhci_ring for use in
+      stream_timeout_function
+    - usb: gadget: send usb_gadget as an argument in get_config_params
+    - usb: chipidea: Add support for VBUS control with PHY
+    - usb: chipidea: Use usb2 phy for Zynq platform
+    - usb: chipidea: Check usb_phy exists before using it
+    - usb: gadget: udc: Remove useless variable assignment in xudc_read_fifo()
+    - usb: gadget: udc: Add return value error handling of function
+    - usb: chipidea: Fix return value handling
+    - usb: chipidea: core: Add return value function check
+    - usb: dwc3: gadget: Add hibernation support when operating in gadget mode
+    - usb: dwc3: core: Add regulator calls for communicating with dwc3 PMU
+    - usb: dwc3: gadget: add support for OTG in gadget framework
+    - usb: dwc3: hibernation: fix scratch buffer allocation
+    - dwc3: core: Enable GUCTL1 chicken bit 10 for fixing crc error after resume
+      bug
+    - dwc3: core: Enable GUCTL1 chicken bit 9 for correcting Inter Packet
+      Delay(IPD)
+    - usb: Add quirk for enabling workaround for BULK IN streams
+    - usb: dwc3: of-simple: Enable CCI support in dwc3 driver
+    - usb: dwc3: update GFLADJ_REFCLK_FLADJ in dwc3_frame_length_adjustment
+    - usb: dwc3: don't setup event buffers when operating in host mode
+    - usb: dwc3: Fix the logic for allocating and setting scratchpad buffers
+    - usb: dwc3: add support for enabling/disabling hibernation dynamically
+    - usb: dwc3: Fix the broken suspend/resume functionality in dwc3
+    - usb: dwc3: Correct usb dma mask for making SMMU work in device mode
+    - usb: dwc3: gadget: ISOC transfers should be stopped before starting a
+      transfer
+    - usb: dwc3: otg: fix broken OTG HNP feature
+    - usb: dwc3: Check for IOC/LST bit in both event->status and TRB->ctrl fields
+    - usb: dwc3: gadget: Don't kick transfer if LST or SHORT bits are set
+    - usb: dwc3: otg: Update Kconfig and Makefile for enabling OTG
+    - usb: dwc3: otg: add support for OTG in DWC3 host driver
+    - usb: dwc3: retain resource index for unforced stops
+    - usb: dwc3: otg: fix the function call used to get otg descriptor
+    - usb: dwc3: otg: remove otg static export warning
+    - usb: dwc3: use proper typecast to handle overflow
+    - usb: dwc3: Initialized variable with a proper value
+    - usb: dwc3: otg: Enable OTG support in dwc3-core driver
+    - usb: dwc3: use PROPERTY_ENTRY_BOOL to initialize property entries
+    - usb: dwc3: Implement stream transfer timeout
+    - usb: dwc3: Enable Xilinx platform only when Regulator is enabled
+    - dt-bindings: gpio: zynqmp: Add binding documentation for modepin
+    - gpio: modepin: Add driver support for modepin GPIO controller
+    - usb: dwc3: xilinx: Add gpio-reset support
+    - usb: dwc3: xilinx: Register drvdata before registering regulator
+    - usb: dwc3: xilinx: Add support for controller power state for host mode
+    - usb: dwc3: xilinx: fixed dwc3-xilinx driver warnings
+    - usb: chipidea: udc: Add xilinx revision support
+    - usb: dwc3: xilinx: Handle dr_mode setting from DT properly
+    - usb: dwc3: gadget: Add new platform_data.h file
+    - usb: dwc3: Fix OTG driver to work with v5.10 kernel
+    - usb: gadget: webcam: Add support for Full HD and 4K UHD Raw Video Formats
+    - usb: dwc3: xilinx: Handle USB3 PHY initialization properly
+    - usb: dwc3: xilinx: enable D3 power state entry feature
+    - usb: dwc3: core: scratchpad buffers allocation handling in host mode
+    - Revert "usb: function: f_tcm: Add support for getting alt interface number"
+    - usb: dwc3: handle usb2.0 gadget mode early hibernation event occurrence
+    - usb: chipidea: udc: make controller hardware endpoint primed
+    - usb: dwc3: Fixed common regulator for multiple controller instance
+    - usb: dwc3: xilinx: fix error handling for reset-gpio
+    - usb: dwc3: xilinx: fix reset-gpio logic
+    - usb: dwc3: core: Update REFCLK_FLADJ for frame length adjustment
+    - usb: dwc3: core: add PM_SLEEP kernel config check
+    - usb: dwc3: gadget: disable hibernation interrupt on gadget enumeration
+    - usb: dwc3: gadget: Increase timeout for CmdAct cleared by device controller
+    - dt-bindings: usb: dwc3: Add interrupt-names to include hibernation interrupt
+    - dt-bindings: usb: dwc3-xilinx: Convert USB DWC3 bindings
+    - Bluetooth: hci_ll: Extend timeout between start and communication
+    - uio: Add dma-buf import ioctls
+    - apf: Add kernel modules to the kernel
+    - uio: rename uio.c -> uio_core.c & unify into uio.ko
+    - microblaze: Swap location of bss and INIT_RAM_FS
+    - microblaze: Change TLB mapping and free space allocation
+    - microblaze: Fix message about compiled-in FDT location
+    - microblaze: Permit pcibios_set_master override
+    - microblaze: pci: Support generic Xilinx AXI PCIe Host Bridge IP driver
+    - dt-bindings: ARM: zynq: Add DT binding for eFuse controller
+    - ARM: zynq: Add support for Zynq-7000S devices
+    - ARM: zynq: Fix prefetch option
+    - zynq: slcr: Introduce new get_ocm_config()
+    - zynq: Add OCM driver
+    - Xilinx: ARM: Devcfg and SLCR drivers updated to support reconfiguration.
+    - dt-bindings: Add doc for xilinx fclk
+    - staging: fclk: Enable pl clock with sysfs entry for set_rate
+    - irqchip: gic: Add remoteproc changes to the driver
+    - watchdog: of_xilinx_wdt: Used dev_dbg()
+    - i2c: mux: pca954x: write to mux channel always
+    - dt-bindings: Add binding for IDT 8T49N24x UFT
+    - clk: Add ccf driver for IDT 8T49N24x UFT
+    - zynqmp: firmware: Adds a driver for loading secure partition from Linux
+    - dt-bindings: pmbus: Add tps544 bindings
+    - pmbus: Add new tps544 power regulator driver
+    - dt-bindings: crypto: Added binding docs for Xilinx ZynqMP SHA3 H/W
+      accelerator
+    - crypto: zynqmp-sha: Adopted SHA3 support for ZynqMP Soc
+    - dt-bindings: crypto: Added binding docs for Xilinx ZynqMP RSA H/W
+      accelerator
+    - crypto: zynqmp-rsa: Adopted RSA support for ZynqMP SoC
+    - phy: dp83867: Add support for SGMII
+    - include: dt-bindings: Add mscc-vsc8531 RGMII clock delay definitions
+    - dt-bindings: mscc: Add RGMII RX and TX delay tuning
+    - phy: mscc: Add support for VSC8531_02 with RGMII tuning
+    - dt-bindings: clock: Adding si5324 bindings
+    - clk: Adding Silicon labs si5324 clock driver
+    - edac: add support for ARM PL310 L2 cache parity
+    - dt-bindings: edac: Add bindings for ZynqMP OCM Controller
+    - edac: zynqmp: Add EDAC support for ZynqMP OCM Controller
+    - dt-bindings: edac: Add bindings for cortex_arm64
+    - EDAC: Add ARM64 EDAC
+    - edac: Add documentation for cortexa53 edac sysfs
+    - edac: Add sysfs entries for cortex arm64
+    - arm64: zynqmp: Change Kconfig dependency for cortexa53 edac
+    - drivers: ata: Add CCI support for SATA if CCI is enabled
+    - samples: xilinx_apm: Add sample application for xilinx_apm
+    - xilinx: Update MAINTAINERS fragment
+    - staging: Add xroeframer driver
+    - staging: xroetrafficgen: initial commit of roe traffic generator driver
+    - mtd: Expand the ecc placement locations to 1260
+    - dt-bindings: power: Add versal power domain bindings
+    - dt-bindings: pci: ZYNQMP PS PCIe Driver Root DMA dt bindings
+    - PCI: ZYNQMP EP driver: Adding support for ZynqMP ep driver
+    - PCI: ZYNQMP EP client driver: Adding support for ZynqMP dma test client
+    - dt-bindings: misc: Add documentation for jesd204b
+    - dt-bindings: misc: Add bindings for JESD phy
+    - misc: jesd204b: Add driver for Xilinx jesd204b
+    - mtd: fixing CFI for Numonyx CFI bug
+    - microblaze: Define SMP safe bit operations
+    - microblaze: Make cpuinfo structure SMP aware
+    - microblaze: Add SMP implementation of xchg and cmpxchg
+    - microblaze: Remove disabling IRQ while pte_update() run
+    - microblaze: Implement architecture spinlock
+    - microblaze: Do atomic operations by using exclusive
+    - microblaze: Prepare entry.S for SMP implementation
+    - microblaze: Rework mmu context management to prepare
+    - microblaze: Enable experimental SMP functionality
+    - dt-bindings: xilinx: Document new evaluation boards
+    - clk: idt: Fix i2cwritebulk() failure
+    - dt-bindings: Add versal clocking wizard
+    - clocking-wizard: Add versal clocking wizard support
+    - Revert "net: phy: ensure phylib state machine is stopped after calling
+      phy_stop"
+    - Revert "net: phy: call state machine synchronously in phy_stop"
+    - dt-bindings: usb: host: ehci-xilinx: Add binding doc
+    - xilinx: Add a github template telling people to not use pull requests there
+    - dt-binding: soc: xilinx: ai-engine: Add new AI engine binding
+    - dt-bindings: soc: xilinx: ai-engine-npi: Add the binding for AIE NPI
+    - misc: ai-engine: Move AI engine reg access to kernel
+    - ARM: zynq: Fix spurious BUG with old DT
+    - spi: spi-cadence: Fix mixed_enum_type coverity warning
+    - spi: spi-cadence: Fix uninit_use coverity warning
+    - dt-bindings: edac: Add bindings for Xilinx Versal EDAC for DDRMC
+    - edac: xilinx: Added EDAC support for Xilinx DDR controller
+    - dt-bindings: Add devicetree documentation for Xilinx PTP timer
+    - ptp: Add Xilinx PTP timer driver
+    - dt-bindings: serial: Add xilinx compatible
+    - i2c-cadence: Replace the value with enum
+    - dmaengine: pl330: Typecast with enum to fix the coverity warning
+    - arm: zynq: delete AFLAGS_suspend.o to fix compile warning
+    - dt-bindings: soc: xilinx: Add the dt binding for AI engine
+    - uio: Add the UIO driver for AI engine
+    - irqchip: gic: Add changes to handle SGI for Zynq Remoteproc driver
+    - pmbus: tps544: adapt for updated pmbus interfaces
+    - crypto: xilinx: zynqmp-aes: Add skcipher based AES driver
+    - dt-bindings: ptp: xilinx: Update new compatible string
+    - ptp: Add support for port offset registers
+    - crypto: xilinx: Drop COMPILE_TEST for CRYPTO_DEV_ZYNQMP_SHA3
+    - clk: si5324: fix linking failure for ARCH arm
+    - include: xilinx_phy: Add Copyright and License
+    - xen: add support for initializing xenstore later as HVM domain
+    - uartlite: Update the default for the parameter
+    - firmware: xilinx: Remove kernel-doc marking instead of regular comment
+    - firmware: xilinx: sync firmware pm_query_id entries with PLM query id
+      entries
+    - firmware: zynqmp: Add Node IDs in xlnx-zynqmp.h
+    - soc: xilinx: vcu: Export functions to obtain logicore settings
+    - clk: xilinx: vcu: Update vcu init/reset sequence
+    - clk: xilinx: vcu: disable aclk incase of probe failure
+    - clk: xilinx: vcu: Populate children node
+    - watchdog: of_xilinx_wdt: use wdd->parent in print
+    - dt-bindings: serial: uartlite: Convert uartlite to json-schema
+    - dt-bindings: clk: xlnx: move xlnx_vcu dt-binding to clk from soc
+    - dt-bindings: clk: xlnx: Update VCU bindings for vcu reset pin
+    - dt-bindings: clock: versal: Remove alt_ref_clk from clock source
+    - arm64: zynqmp: Add Xilinx SHA3 node
+    - arm64: zynqmp: Add support for ZynqMP RSA H/W accelerator
+    - dt-bindings: zynqmp: add RPU nodes
+    - dt-bindings: zynqmp: Add new PD_PL macro
+    - mtd: cfi: Add macro for Winbond NOR flashes
+    - firmware: zynqmp: Add sysfs entry for runtime features
+    - arm: zynq: add "-march=armv7-a" to AFLAGS
+    - arm: zynq: don't remove -march=armv6k from KBUILD_AFLAGS
+    - dt-bindings: usb: misc: Add binding for Microchip usb5744 hub
+    - usb: misc: usb5744: add support for USB hub controller
+    - dt-bindings: usb: misc: Add binding for Microchip usb2244 Controller
+    - usb: misc: usb2244: add support for USB2 ultra fast sd controller
+    - dt-bindings: Add Xilinx AMS binding documentation
+    - iio: adc: Add Xilinx AMS driver
+    - dt-bindings: iio: xilinx: Add Documentation for Sysmon
+    - iio: versal-sysmon: add driver for Versal Sysmon
+    - dt-bindings: gpio: zynq: Add all the supported compatibles
+    - dt-bindings: iio: adc: Add ti,ina260.yaml
+    - drivers: iio: Add support for TI INA260 power monitors
+    - iio: adc: versal-sysmon: Add runtime resume function for sysmon
+    - dt-bindings: nvmem: Added nodes for BBRAM and volatile user keys
+    - nvmem: Add driver for BBRAM and volatile user keys access
+    - remoteproc: Add support for peek from remote and acking kick from remote
+    - dt-bindings: Add Zynq remoteproc binding
+    - remoteproc: Add support for AMP on Zynq platform
+    - dt-bindings: remoteproc: Add documentation for ZynqMP R5 rproc bindings
+    - remoteproc: Add initial zynqmp R5 remoteproc driver
+    - dt: bindings: sound: Add DT bindings for Xilinx ZynqMP DP audio
+    - sound: soc: xilinx: Add ZynqMP DP subsystem audio drivers
+    - dt-bindings: ASoC: xlnx-v-uhdsdi-audio: document sdi audio bindings
+    - AsoC: xlnx: add platform driver to support SDI audio
+    - dt-bindings: ASoC: Document audio formatter bindings for xlnx,audio-
+      formatter
+    - ASoC: xlnx: add pcm formatter platform driver
+    - ASoC: xlnx: add PL sound card support
+    - dt-bindings: ASoC: xlnx,spdif: Document spdif bindings
+    - ASoC: xlnx: add SPDIF audio driver
+    - ASoC: xlnx,i2s: dt-bindings: add reference to audio formatter
+    - ASoC: xlnx: change I2S driver data
+    - drm: drm_fourcc: Introduce macro-pixel info to drm_format_info
+    - drm: fourcc: Add drm_format_plane_width_bytes()
+    - drm: drm_fourcc: Add new formats for Xilinx IPs
+    - drm: fourcc: Add new formats needed by Xilinx IP
+    - drm: drm_fourcc: Correct the DRM YUV444 10bpc
+    - uapi: drm: Add AVUY fourcc
+    - drm: Add new flags for interlaced alternate fields
+    - uapi: media: New fourcc codes needed by Xilinx Video IP
+    - media: Add documentation for YUV420 bus format
+    - dt-bindings: dmaengine: xilinx_frmbuf: Video Framebuffer IP
+    - dmaengine: xilinx_frmbuf: New driver for Video Framebuffer IP
+    - drm: panel: Added timing for AUO B101UAN01 display panel
+    - media: entity: Add has_route entity operation
+    - media: entity: Add media_entity_has_route() function
+    - v4l: subdev: Add [GS]_ROUTING subdev ioctls and operations
+    - v4l: Add RGB 8:8:8 media bus format on 24 and 32 bit busses
+    - v4l: Add VUY8 24 bits bus format
+    - uvcvideo: Xilinx: Bump up URBS and MAX_PACKETS
+    - v4l: xilinx: Kconfig: Add missing DMADEVICES dependencies
+    - media: xilinx: Ensure Video Framebuffer selected by Kconfig
+    - v4l: xilinx: Add Video Remapper driver
+    - media: xilinx: Add Color Filter Array (CFA) driver
+    - media: xilinx: Add Chroma Resampler (CRESAMPLE) driver
+    - media: xilinx: Add RGB to YUV (RGB2YUV) driver
+    - media: xilinx: Add Scaler driver (SCALER) driver
+    - media: xilinx: Add AXI4 stream switch driver
+    - media: xilinx: Add HLS core driver
+    - media: xilinx: Integrate TPG v7 support
+    - media: xilinx: tpg: Block comments
+    - media: xilinx: Refactor VTC configuration code
+    - media: xilinx: vip: Add the pixel format for RGB24
+    - v4l: xilinx: dma: Terminate DMA when stream on fails
+    - media: xilinx: dma: Enable use of Framebuffer Write IP in V4L2 Driver
+    - v4l: xilinx: dma: Remove colorspace check in xvip_dma_verify_format
+    - media: xilinx: Improve pipeline management code
+    - media: v4l: Group Xilinx downstream formats
+    - documentation: dt: add bindings documentation for xilinx video demosaic
+      driver
+    - v4l: xilinx-demosaic: driver support for xilinx video demosaic
+    - documentation: dt: add bindings documentation for vpss scaler
+    - v4l: xilinx-vpss-scaler: driver support for xilinx vpss scaler
+    - media: v4l: Add HDR support through compound controls
+    - media: v4l2-core: Update V4L2 framework with new fourcc codes
+    - v4l2-core: Update entries for XV15 and XV20 contiguous formats
+    - media: v4l2-ioctl: Add 12 and 16 bpc RGB pixel formats
+    - media: v4l2-ioctl: Add YUV 12bit and 16bit pixel formats
+    - media: v4l2-ioctl: Use correct fourcc for YUV444 10bit format
+    - media: v4l2-ioctl: Add YUV444 12bit and 16bit pixel formats
+    - media: v4l2-ioctl: Add description for new pixel formats
+    - media: videodev2.h: add Hybrid Log Gamma transfer function define
+    - media: videodev2.h: Add control type for HDR
+    - dt: bindings: media: xilinx: Documentation for Xilinx UHDSDI Rx driver
+    - v4l: xilinx: Driver support for Xilinx UHDSDI Rx subsystem
+    - documentation: dt: add bindings documentation for gamma lut ip
+    - v4l: xilinx-gamma: initial driver support for xilinx video gamma lut ip
+    - Documentation: DT: Add bindings documentation for VPSS CSC
+    - v4l: xilinx-vpss-csc: driver support for xilinx vpss csc
+    - drivers: media: Customized adv7511 for Xylon LogiCVC (deprecated)
+    - drm: mipi: Bring DT format description closer to the hardware
+    - drm: xlnx: Xilinx DRM KMS driver
+    - dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings
+    - dt-bindings: display: xlnx: Add bridge bindings
+    - drm: xlnx: drv: Add Xilinx bridge support
+    - dt-bindings: display: xlnx: Adding dsi bindings
+    - drm: xlnx: dsi: Adding dsi driver to new framework
+    - drm: xlnx: adding cursor width / height support
+    - dt-bindings: display: xlnx: Adding mixer bindings
+    - drm: xlnx: mixer: Initial video mixer driver
+    - drm: Add generic HDR support
+    - dt-bindings: display: xlnx: Adding sdi bindings
+    - drm: xlnx: sdi: Adding sdi-tx driver
+    - dt-bindings: dma: xilinx_frmbuf: Add support for 12 and 16 bpc RGB formats
+    - dma: xilinx: Support early callback modes
+    - dt-bindings: display: xlnx: Adding pl_disp bindings
+    - drm: xlnx: DRM KMS driver for xilinx display pipeline
+    - dt: bindings: display: xlnx: Adding csc bindings
+    - drm: xlnx: csc: Adding vpss-color space converter driver
+    - dt: bindings: display: xlnx: Adding scaler bindings
+    - drm: xlnx: scaler: Adding vpss-scaler driver
+    - dt-bindings: display: xlnx: Added vpss bridge phandle as optional property
+    - dt: bindings: display: xlnx: Adding gpio reset entry
+    - drm: xlnx: scaler: Adding vpss-scaler reset through gpio
+    - drm: xlnx: scaler: Adding Zero out H-phase array before changing resolution
+    - drm: xlnx: correcting data type for cursor with and height
+    - media: Add new dt-bindings/vf_codes for supported formats
+    - v4l: xilinx: dma: Update video format descriptor
+    - v4l: xilinx: dma: Add multi-planar support
+    - v4l: xilinx: dma: Fix v4l2 enumeration callback for multiplanar
+    - v4l: xilinx: dma: Add scaling and padding factor functions
+    - v4l: xilinx: dma: Get scaling and padding factor to calculate DMA params
+    - drm: xlnx: scaler: Add YUV420 support
+    - drm: xlnx: csc: Add YUV420 support
+    - Documentation: media: Correct dt-bindings doc for Gamma LUT IP
+    - dt-bindings: display: xlnx: Modifing mixer compatible string
+    - v4l: xilinx-tpg: Add YUV 420 media bus format support to TPG driver
+    - v4l: xilinx: dma: Fix sizeimage calculation
+    - v4l: xilinx: dma: Handle 10 bit format calucations for XV20
+    - v4l: xilinx: dma: Fix bytes per line calculation
+    - v4l: xilinx: Add BGR color format support.
+    - media: xilinx: vip: Correct the fourcc code for BGRX8 format.
+    - dt: bindings: media: xilinx: Remove unimplemented TPG compatible string
+    - v4l: xilinx: dma: Add XV15 and XV20 contiguous format support
+    - uvcvideo: Prevent new URBs being processed at stream stop
+    - dt: bindings: display: xlnx: Updated gpio reset entry
+    - drm: xlnx: scaler: Updating vpss-scaler reset logic
+    - dt: bindings: display: xlnx: Adding gpio reset entry
+    - drm: xlnx: csc: Adding vpss-csc reset through gpio
+    - xilinx: v4l2: dma: Bug fix in single plane support
+    - bindings: display: xlnx: Fixing device tree documentation
+    - dt-bindings: display: xlnx: mixer: Add supported formats table
+    - dt-bindings: display: xlnx: mixer: Update example to fix format strings
+    - v4l: xilinx: dma: Add interlaced support
+    - v4l: xilinx: dma: Terminate DMA when media pipeline fails to start
+    - xilinx: v4l2: dma: Add multiple output support
+    - dt-bindings: display: xlnx: mixer: Added xlnx,num-layers description
+    - dt-bindings: display: xlnx: mixer: Adding xlnx,layer-primary property
+    - dt-bindings: display: xlnx: Add VTC bindings
+    - drm: xlnx: Add a Video Timing Controller(VTC) driver
+    - dt-bindings: display: xlnx: mixer: Adding xlnx vtc bridge support
+    - dt-bindings: display: xlnx: Add VTC bridge support to PL display
+    - xilinx: v4l: dma: Multi-threading issue
+    - xilinx: v4l: dma: Fix bug in calculating interlaced height
+    - dt: bindings: media: xilinx: Doc for Xilinx AXI4-Stream Switch driver
+    - v4l: xilinx: Driver support for Xilinx AXI4-Stream Switch
+    - media: platform: xilinx: Fix Kconfig indentation
+    - xilinx: v4l: dma: Add ioctl operations for v4l2 output device
+    - xilinx: v4l: dma: Add DMA input direction support
+    - xilinx: v4l: dma: Add format enumeration for output
+    - v4l: xilinx: scd: Add v4l2 custom events
+    - documentation: dt: add bindings documentation for Scene Change Detection
+    - v4l: xilinx: scd: New Scene Change Detection driver
+    - documentation: dt: add bindings documentation for multi-scaler
+    - platform: xilinx: Add mem to mem Multi-Scaler driver (XM2MSC)
+    - dt: bindings: media: xilinx: Documentation for mem2mem driver
+    - xilinx: v4l: mem2mem: Initial version of driver
+    - v4l: dma: Use media graph traversal to stream on/off subdevs
+    - drm: fb: Modify check to ensure correctness of flags
+    - documentation: dt: vtpg: Add support for max width and height
+    - v4l: xilinx: tpg: Add check for max width and height
+    - documentation: dt: demosaic: add support for max width and height
+    - documentation: dt: gamma: Add support for max width and height
+    - drm: xlnx: scaler: Fix array out of bound access
+    - xilinx: v4l: dma: Remove unused function definition
+    - dt-bindings: media: xilinx: demosaic: Make max width, height mandatory
+    - dt-bindings: media: xilinx: vpss-csc: Make max width, height mandatory
+    - xilinx: v4l: dma: In case of error xvip_pipeline_start_stop should return
+      gracefully
+    - xilinx: v4l: vipp: Avoid decrementing refcount of a node twice
+    - xilinx: v4l: dma: Invoke s_power function of subdevice
+    - drm: xlnx: Select VIDEOMODE_HELPERS when DRM_XLNX_PL_DISP is selected
+    - media: ov5640: fix get_light_freq on auto
+    - media: ov5640: Don't access ctrl regs when off
+    - xilinx: v4l: dma: Stop subdevs in reverse order of starting
+    - documentation: dt: Add bindings documentation for Streaming SCD
+    - drm: xlnx: crtc: Fix max width and height overflow
+    - dt-bindings: display: xlnx: mixer: Correct DRM fourcc for BGR8 and RGB8
+    - dt: bindings: media: xilinx: Add clock support to AXI4 Stream switch
+    - dt-bindings: display: xlnx: Add device tree binding for xlnx control drivers
+    - media: xilinx: tpg: Add pixel per clock dt support
+    - dt: bindings: media: xilinx: tpg: Add ppc dt bindings.
+    - media: xilinx: tpg: v4l subdevice controls to set fps
+    - media: xilinx: vtc: Dynamically calculate pixel clock
+    - documentation: dt: multi-scaler: Add properties for pixels per clock
+    - documentation: dt: multi-scaler: Add clock framework support
+    - dt-bindings: display: xlnx: Add clock framework support to DSI Tx
+    - dt-bindings: display: xlnx: Add clock framework support to VPSS CSC bridge
+      driver
+    - drm: xlnx: csc: Add clock framework support
+    - dt-bindings: display: xlnx: Add clock framework support to VPSS Scaler
+      bridge driver
+    - drm: xlnx: scaler: Add support for clock framework
+    - dt-bindings: display: xlnx: Add clock framework support to VTC bridge driver
+    - media: xilinx: tpg: dt pixel per clock validate.
+    - v4l: xilinx: dma: Add control for low latency
+    - v4l: xilinx: dma: Add s_ctrl ioctl for low latency capture
+    - v4l: xilinx: vip: Add 12 and 16 bpc RAW and RGB color formats
+    - dt-bindings: media: xilinx: tpg: Update for v8.0
+    - media: xilinx: tpg: Add support for v8.0
+    - dt-bindings: display: xlnx: vpss-csc: Add max width and height properties
+    - drm: xlnx: csc: Add max width and height dt properties
+    - dt-bindings: display: xlnx: Add max width and height as mandatory properties
+    - drm: xlnx: scaler: Add max width and height properties
+    - v4l: xilinx: tpg: Use 10bit media bus codes
+    - v4l: xilinx: vip: Add YUV 10bit media bus formats
+    - v4l: xilinx: vip: Add scaling and padding factor for XY10
+    - v4l: xilinx: vip: Use correct media bus code for RGB 10bit format
+    - v4l: xilinx: vip: Fix stride calculation
+    - v4l: xilinx: vip: Add YUV444 12bit and 16bit formats
+    - dt-bindings: display: xlnx: mixer: Updated compatible string
+    - v4l: xilinx: vip: Keep NV16 first in vip table
+    - v4l: xilinx: vip: Use the right media code for 422 16bit formats
+    - dt-bindings: display: xlnx: dsi: Add command mode support
+    - dt-bindings: display: xlnx: Add support for vpss ip version 2.2
+    - drm: xlnx: scaler: Add support for ip version 2.2
+    - dma: xilinx: Disable low latency capture in file ops open
+    - staging: dt-bindings: xlnxsync: Add initial bindings for Xilinx Synchronizer
+    - staging: xlnxsync: Add driver for Xilinx Synchronizer
+    - dt-bindings: Add device tree binding for xilinx mpeg2tsmux driver
+    - staging: xlnx_tsmux: Initial version of xlnx mpeg2tsmux driver
+    - drm: xlnx: scaler: Improve quality by adding more coefficients
+    - drm/fb_helper: Enable drm_leak_fbdev_smem by default for zynqmp
+    - dt-bindings: display: xlnx: mixer: Add rev 5.0 to compatible string
+    - v4l: xilinx: dma: Prevent divide by zero error
+    - v4l: xilinx: vipp: move xvip_entity_start_stop() to xilinx-vipp
+    - v4l: xilinx: vipp: use async list for start and stop
+    - v4l: xilinx: vipp: do enabling in the dependency check
+    - v4l: xilinx: vipp: remove a loop for graph start / stop
+    - v4l: xilinx: vipp: Change xvip_entity_start/stop to take graph entity
+    - v4l: xilinx: vipp: Remove set streaming on subdev
+    - drm: xlnx: fix some typos in the Kconfig help texts
+    - v4l: xilinx: sdi: Fix the uapi header license
+    - v4l: xilinx: hls: Fix the uapi header license
+    - v4l: xilinx: events: Fix the uapi header license
+    - v4l: xilinx: tpg: Don't read version if HLS IP
+    - v4l: xilinx: dma: Add control handler to v4l2 device
+    - dt: bindings: media: xilinx: Documentation for Xilinx DP Rx subsystem
+    - v4l: xilinx: Driver support for Xilinx DP Rx subsystem
+    - dt-bindings: display: xlnx: mixer: Updated layer max height and width ranges
+    - v4l: xilinx: vipp: Perform stream start/stop at pipeline level
+    - v4l: xilinx: vipp: remove unused variable
+    - v4l: xilinx: dma: Remove struct xventity_list
+    - dt-bindings: display: xlnx: Add DisplayPort Tx bindings
+    - drm: xlnx: dptx: Add DisplayPort tx driver
+    - v4l: xilinx: vip: Fix V4L2_PIX_FMT_XY10 bpl_factor
+    - v4l: xilinx: vip: Fix CHECKED_RETURN warnings
+    - v4l: xilinx: vip: Fix UNINIT warnings
+    - v4l: xilinx: dma: Fix OVERFLOW_BEFORE_WIDEN warnings
+    - media: xilinx: vtc: Fix warning for OVERFLOW_BEFORE_WIDEN
+    - v4l: xilinx: tpg: Fix warnings for NULL_RETURNS
+    - v4l: xilinx: tpg: Fix warnings for CHECKED_RETURN
+    - drm: xlnx: zynqmp_dp: Fix UNINIT type warning
+    - media: dt-bindings: media: i2c: Add bindings for AP1302
+    - media: i2c: Add ON Semiconductor AP1302 ISP driver
+    - dt: bindings: media: xilinx: Doc for Xilinx AXI4-Stream Broadcaster driver
+    - v4l: xilinx: Driver support for Xilinx AXI4-Stream Broadcaster
+    - drm: xlnx: Update DP subsystem with downstream version
+    - drm: xlnx: add a new member extra_name for xlnx_bridge structure
+    - drm: xlnx: bridge: Fix xlnx_bridge_unregister issue
+    - drm: xlnx: zynqmp: remove layer sub node based on DP DT change
+    - dt-bindings: media: xilinx: Add reserved memory usage information
+    - v4l2: xilinx: vipp: Allow reserving memory and DMA using 64bit addresses
+    - dt-bindings: display: xlnx: mixer: Add example for reserved memory usage
+    - dmaengine: xilinx: dpdma: Add support for cyclic dma mode
+    - drm: fourcc: Mark XV20 and XV15 formats as YUV based
+    - phy: Add HDMI PHY configuration options
+    - dt-bindings: media: xilinx: xcsi2rxss: Add YUV420 8b support
+    - v4l: xilinx: xcsi2rxss: Add support for YUV 420 8bpc
+    - v4l: xilinx: csi2rxss: Remove downstream controls
+    - v4l: xilinx: xcsi2rxss: Fix warnings for NULL_RETURNS
+    - v4l2: xilinx: dma: Align width as per underlying DMA prerequisite
+    - v4l: xilinx: vip: Fix bpl_factor values for Bayer formats
+    - v4l: xilinx: vip: Fix incorrect media bus format code
+    - v4l: xilinx: vip: Add 10-bpp Bayer formats support
+    - phy: xilinx: hdmi: Add linerate, nchannels and reset_gt
+    - dt-bindings: media: xilinx: Add HDMI 2.1 Rx subsystem documentation
+    - v4l: xilinx: hdmirx: Add HDMI 2.1 Rx subsystem driver
+    - drm: xlnx: drv: initialize vblank for all crtcs
+    - dt-bindings: display: xlnx: Add HDMI 2.1 Tx subsystem documentation
+    - drm: xlnx: hdmi: Add HDMI 2.1 Tx subsystem driver
+    - dt-bindings: dmaengine: xilinx_dma: Add MCMDA channel ID index description
+    - drm: xlnx: bridge: check bridge->debugfs_file->status when calling strlen
+    - drm: xlnx: zynqmp: tpg should use swap_coeffs as csc matrix
+    - media: vivid: Fix the check of frame interval index
+    - kbuild: add xilinx-sdirxss.h/xilinx-hls.h/xilinx-v4l2-events.h to no-header-
+      test
+    - dt-bindings: media: xilinx: Add xlnx,atomic_streamon documentation
+    - v4l: xilinx: vip: Allow media pipeline enable with single dma start
+    - dt: bindings: phy: Documentation for Xilinx HDMI PHY controller
+    - phy: xilinx-xhdmiphy: initial driver support for xilinx HDMI PHY 2.1 IP
+    - v4l: xilinx: vip: Add support for 3 planar YUV444 8bpc
+    - v4l: xilinx: dma: Add support for 3 planar YUV444 8bpc format
+    - v4l: xilinx: vip: Fix alignment to match open parenthesis
+    - dt-bindings: dmaengine: zynqmp_dma: Convert zynqmp dma bindings to yaml
+    - dt: bindings: phy: Documentation for Xilinx GT QUAD BASE PHY controller for
+      DP
+    - phy: Add driver for GTQUAD BASE for Displayport
+    - dmaengine: xilinx: dpdma: Fix race condition in vsync IRQ
+    - gpio: xilinx: Trivial patch
+    - mmc: sdhci-of-arasan: Add support for dynamic configuration
+    - spi: spi-cadence: Fix SPI CS gets toggling sporadically
+    - mtd: spi-nor: Add dual parallel and stacked mode support
+    - spi: spi-zynqmp-gqspi: Remove txfifo empty check during chip select/deselect
+    - spi: spi-zynqmp-gqspi: Increase timeout interval during data transfer
+    - spi: spi-zynqmp-gqspi: Update driver to support both IO and dma modes
+    - dt-bindings: spi: spi-zynqmp-gqspi: Add support for Xilinx Versal QSPI
+    - spi: spi-zynq-gqspi: Set appropriate tapdelay values
+    - mtd: spi-nor: Update flash lock/unlock feature
+    - mtd: spi-nor: Add EAR support in spi-nor framework
+    - spi: spi-zynqmp-gqspi: Add dual parallel and stacked mode support in driver
+    - spi: spi-zynq-qspi: Add dual parallal and stacked support
+    - spi: spi-zynq-qspi: Fixed buffer overflow in zynq_qspi_exec_mem_op
+    - mtd: spi-nor: Don't parse 4BAIT via Zynq QSPI
+    - mtd: spi-nor: Fix call trace when qspi driver built as module
+    - spi: spi-cadence: Fix kernel-doc format for resume/suspend
+    - spi: spi-cadence: Align function name s/cnds/cdns/g
+    - spi: spi-zynqmp-gqspi: Fix chipselect timeout issue
+    - spi: spi-zynqmp-gqspi: Fix the zynqmp qspi driver call to get the spi
+      controller devdata
+    - spi: spi-zynqmp-gqspi: Fix suspend/resume
+    - spi: spi-zynqmp-gqspi: Fix erase failure when tx buswidth is 4
+    - mtd: spi-nor: Update flash properties in flash_info table
+    - spi: spi-cadence-quadspi: Add support for Stacked mode
+    - spi: spi-xilinx: Updated axi-qspi controller driver
+    - fpga: region: Update runtime PM handling logic
+    - fpga: fpga-region: Add missing kernel-doc description
+    - v4l: xilinx: dprx: Add MMCM configuration for rx_dec_clk for versal systems
+    - firmware: xilinx: Fix incorrect return val in zynqmp_pm_sec_read_reg()
+    - ARM: zynq: Add/Update/Sync DTs for xilinx platforms
+    - arm64: zynqmp: Add/Update/Sync DTs for xilinx platforms
+    - ARM: xilinx: Add zynq defconfig
+    - arm64: xilinx: Add defconfig fragments
+    - microblaze: defconfig: Enable the Marvell phy driver
+    - microblaze: Defconfig sync
+    - microblaze: Add defconfig and DT for SMP design
+    - phy: xilinx-xhdmiphy: Set connector linerate in HDMI-RX TMDS mode
+    - phy: xilinx-xhdmiphy: Fix connector linerate setting in FRL mode
+    - misc: xilinx_flex: Prevent exiting with mutex
+    - dt-bindings: net: cdns,macb: Convert to json-schema
+    - dt-bindings: net: cdns,macb: Add versal compatible string
+    - dt-bindings: net: cdns,macb: added generic PHY and reset mappings for ZynqMP
+    - net: macb: Added ZynqMP-specific initialization
+    - net: macb: Add zynqmp SGMII dynamic configuration support
+    - iio: adc: versal-sysmon: Add macros for delayed work
+    - arm64: configs: xilinx: Enable default usb ethernet and serial gadget
+    - xilinx: Sync defconfig with current Kconfig layout
+    - net: xilinx: Update Kconfig to select XILINX_AXI_EMAC for XILINX_TSN
+    - staging: xlnxsync: Added IOCTL to reset the current syncIp slot
+    - usb: dwc3: gadget: Ignore Update Transfer cmd params
+    - usb: dwc3: gadget: Skip checking Update Transfer status
+    - usb: dwc3: gadget: Handle pending stream transfer bit
+    - misc: xilinx-ai-engine: add device tree overlay support
+    - misc: xilinx-ai-engine: Add frequency scaling kernel APIs
+    - misc: xilinx-ai-engine: Fix QoS and frequency calculations as defined by PLM
+    - misc: xilinx-ai-engine: Remove get/set frequency IOCTLs
+    - misc: xilinx-ai-engine: Add get partition current freq sysfs entry
+    - dt-bindings: media: xilinx: hdmirxss: Add v1.2 compatible string
+    - v4l: xilinx: hdmirxss: Add v1.2 compatible string
+    - v4l: xilinx: hdmirxss: Fix DDC writes for 0xFF field mask
+    - v4l: xilinx: hdmirxss: Correctly disable timers while initializing
+    - microblaze: Add xmb_manager_register function
+    - dt-bindings: misc: tmr-manager: Add device-tree binding for TMR Manager
+    - drivers: misc: Add Support for TMR Manager
+    - microblaze: Add custom break vector handler for mb manager
+    - microblaze: Add support for error injection
+    - dt-bindings: misc: tmr-inject: Add device-tree binding for TMR Inject
+    - drivers: misc: Add Support for TMR Inject IP
+    - usb: misc: Fix gcc warnings for usb2244 and usb5744 driver
+    - v4l: xilinx: hdmirxss: Fix kernel-doc warnings
+    - dt-bindings: soc: xilinx: ai-engine: add aie gen and mem rows
+    - misc: xilinx-ai-engine: move mem clear to dev ops
+    - misc: xilinx-ai-engine: device struct for tile type
+    - misc: xilinx-ai-engine: get device properties from device tree
+    - misc: xilinx-ai-engine: remove hard coded row attributes
+    - misc: xilinx-ai-engine: issue privilege ops to firmware
+    - misc: xilinx-ai-engine: add support for aieml
+    - misc: xilinx-ai-engine: enable aieml device support
+    - misc: xilinx-ai-engine: disable rsc mgr for aieml
+    - misc: xilinx-ai-engine: disable sysfs nodes for aieml
+    - misc: xilinx-ai-engine: disable interrupts for aieml
+    - firmware: xilinx: Move FIRMWARE_VERSION_MASK to xlnx-zynqmp.h
+    - iio: adc: versal-sysmon: Add support for secure access
+    - iio: adc: versal-sysmon: Add support for events on slave SLRs
+    - drm: xlnx: Update dependency for DRM PL display driver
+    - drm: xlnx: Update dependency for ZynqMP DP driver
+    - xilinx: zynq: enabling UEVENT_HELPER
+    - arm64: zynqmp: Add resets property to sdhci nodes
+    - arm64: zynqmp: Add support for zcu102-rev1.1 board
+    - arm64: zynqmp: Add support for Xilinx Kria SOM board
+    - arm64: xilinx: Fix dtb filename for smk-k26 board
+    - arm64: zynqmp: Add the latest changes for SOM boards
+    - arm64: zynqmp: Add all missing dt files for Xilinx boards
+    - arm64: versal: Add all missing dt files for Xilinx boards
+    - dt-bindings: ptp: xilinx: Add additionalProperties
+    - ASoC: xlnx: Set dai_fmt for hdmi and dp sound cards
+    - firmware: xilinx: enable feature check for ZU+
+    - usb: gadget: tcm: error handling for each command allocation
+    - arm64: zynqmp: Fix bias setting for gem1
+    - v4l: xilinx: hls: remove from the UAPI header kernel specific __user macro
+    - usb: dwc3: xilinx: Update GPIO access api with sleep
+    - serial: pl011: Add missing request/release functions
+
+ -- Hsuan-Yu Lin <shane.lin@canonical.com>  Wed, 02 Mar 2022 16:00:34 +0800
+
+linux-xilinx-zynqmp (5.15.0-1000.0) jammy; urgency=medium
+
+  * empty entry
+
+ -- Wen-chien Jesse Sung <jesse.sung@canonical.com>  Sun, 16 Aug 2020 15:59:56 +0800
--- linux-xilinx-zynqmp-5.15.0.orig/debian/cloud-tools/hv_get_dhcp_info
+++ linux-xilinx-zynqmp-5.15.0/debian/cloud-tools/hv_get_dhcp_info
@@ -0,0 +1,55 @@
+#!/bin/bash
+
+# This example script retrieves the DHCP state of a given interface.
+# In the interest of keeping the KVP daemon code free of distro specific
+# information; the kvp daemon code invokes this external script to gather
+# DHCP setting for the specific interface.
+#
+# Input: Name of the interface
+#
+# Output: The script prints the string "Enabled" to stdout to indicate
+#	that DHCP is enabled on the interface. If DHCP is not enabled,
+#	the script prints the string "Disabled" to stdout.
+#
+# Each Distro is expected to implement this script in a distro specific
+# fashion. 
+
+#set -x
+
+IF_FILE="/etc/network/interfaces"
+NMCMD="nmcli"
+
+function checknetworkmanager {
+	#Assumes if $NMCMD exists, inteface exists and interface is not
+	#  in $IF_FILE then dhcp is being used by NM
+        if  hash $NMCMD >/dev/null 2>&1  ; then
+                if  $NMCMD  dev status |grep -q $1  ; then
+                        echo "Enabled"
+                else
+                        echo "Disabled"
+                fi
+        else
+                #Give up
+                echo "Disabled"
+        fi
+}
+
+if [ -z $1 ]  ; then echo "Disabled"; exit; fi
+
+if [ -e $IF_FILE ]; then
+	if grep -v -e "^#" $IF_FILE|grep -q $1 ; then
+		#interface exists so
+		if grep -q -e $1\.\*dhcp $IF_FILE; then 
+			echo "Enabled"; exit;
+		else
+			echo "Disabled"; exit;
+		fi
+	else
+		checknetworkmanager $1
+		exit
+	fi
+else
+	checknetworkmanager $1
+	exit
+fi
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/cloud-tools/hv_get_dns_info
+++ linux-xilinx-zynqmp-5.15.0/debian/cloud-tools/hv_get_dns_info
@@ -0,0 +1,13 @@
+#!/bin/bash
+
+# This example script parses /etc/resolv.conf to retrive DNS information.
+# In the interest of keeping the KVP daemon code free of distro specific
+# information; the kvp daemon code invokes this external script to gather
+# DNS information.
+# This script is expected to print the nameserver values to stdout.
+# Each Distro is expected to implement this script in a distro specific
+# fashion. For instance on Distros that ship with Network Manager enabled,
+# this script can be based on the Network Manager APIs for retrieving DNS
+# entries.
+
+cat /etc/resolv.conf 2>/dev/null | awk '/^nameserver/ { print $2 }'
--- linux-xilinx-zynqmp-5.15.0.orig/debian/cloud-tools/hv_set_ifconfig
+++ linux-xilinx-zynqmp-5.15.0/debian/cloud-tools/hv_set_ifconfig
@@ -0,0 +1,288 @@
+#!/usr/bin/python3
+#
+# hv_set_ifconfig <config> -- take the hv_kvp_daemon generated configuration
+#                             file and apply it to the Ubuntu configuration.
+#
+
+# CONFIG example:
+# HWADDR=11:22:33:44:55:66
+# DEVICE=foo1
+# DHCP=yes
+
+# CONFIG example:
+# HWADDR=11:22:33:44:55:66
+# DEVICE=foo1
+# IPADDR=192.168.99.10
+# GATEWAY=192.168.99.1
+# DNS1=192.168.88.250
+# IPADDR2=192.168.99.11
+# IPV6ADDR=2001:DB8:99::10
+# IPV6NETMASK=64
+# IPV6_DEFAULTGW=2001:DB8:99::10
+
+# set interfaces in hv_kvp_daemon style
+import fileinput
+import sys
+import errno
+import os
+import shutil
+import tempfile
+import subprocess
+
+if_filename="/etc/network/interfaces"
+
+# Drop our output (XXX?)
+sys.stdout = open(os.devnull, 'w')
+sys.stderr = open(os.devnull, 'w')
+
+# Confirm we can open the network configuration.
+try:
+    if_file=open(if_filename,"r+")
+except IOError as e:
+    exit(e.errno)
+else:
+    if_file.close()
+
+# Usage: hv_set_ifconfig <config>
+if len(sys.argv) != 2 :
+    exit(errno.EINVAL)
+
+#
+# Here is the format of the ip configuration file:
+#
+# HWADDR=macaddr
+# DEVICE=interface name
+# BOOTPROTO=<protocol> (where <protocol> is "dhcp" if DHCP is configured
+#                       or "none" if no boot-time protocol should be used)
+#
+# IPADDR0=ipaddr1
+# IPADDR1=ipaddr2
+# IPADDRx=ipaddry (where y = x + 1)
+#
+# NETMASK0=netmask1
+# NETMASKx=netmasky (where y = x + 1)
+#
+# GATEWAY=ipaddr1
+# GATEWAYx=ipaddry (where y = x + 1)
+#
+# DNSx=ipaddrx (where first DNS address is tagged as DNS1 etc)
+#
+# IPV6 addresses will be tagged as IPV6ADDR, IPV6 gateway will be
+# tagged as IPV6_DEFAULTGW and IPV6 NETMASK will be tagged as
+# IPV6NETMASK.
+#
+
+kvp=dict(line.strip().split("=") for line in fileinput.input())
+
+# Setting the hwaddress to something azure is not expecting is fatal
+# to networking.
+if not "HWADDR" in kvp :
+    exit(errno.EPROTO)
+
+# Confirm we have a device specified.
+if not "DEVICE" in kvp :
+    exit(1)
+
+autolist = []
+output=[]
+basename=kvp["DEVICE"]
+
+# DNS entries will go with the first interface and there can be a max
+# of three.  These will be emitted with the first interface.
+dns = []
+for count in (1, 2, 3):
+    key = "DNS" + str(count)
+    if key in kvp:
+        dns += [kvp[key]]
+dns_emitted = False
+
+# IPV4 may either be dhcp or static.
+if ("DHCP" in kvp and kvp["DHCP"] == "yes") or \
+   ("BOOTPROTO" in kvp and kvp["BOOTPROTO"] == "dhcp"):
+    autolist.append(basename)
+    output += ["iface " + basename  + " inet dhcp"]
+    output += [""]
+else:
+    # Matchup the interface specific lines
+
+    # No real max for the number of interface + aliases ...
+    # only required is the address (but mate everything up that comes in.
+
+    # IPv4 -- ensure we sort by numeric suffixes.
+    v4names = [ int(name[6:]) for name in kvp.keys() if name.startswith("IPADDR") ]
+    v4names.sort()
+
+    for if_count in v4names:
+        ifname = basename
+        which = str(if_count)
+
+        if if_count:
+            ifname += ":" + str(if_count)
+            which_gw = which
+        else:
+            which_gw = ""
+
+        if not ifname in autolist:
+            autolist += [ifname]
+
+        output += [ "iface " + ifname + " inet static" ]
+        output += [ "\t" + "address " + kvp["IPADDR" + which] ]
+        if "NETMASK" + which in kvp:
+            output += [ "\tnetmask " + kvp["NETMASK" + which] ]
+        if "GATEWAY" + which_gw in kvp:
+            output += ["\tgateway " + kvp["GATEWAY" + which_gw]]
+
+        if not dns_emitted:
+            dns_emitted = True
+            output += ["\tdns-nameservers " + ' '.join(dns)]
+        output += [""]
+
+# IPv6 requires a netmask
+# If an ipv6 exists, you'll want to turn off /proc/sys/net/ipv6/conf/all/autoconf with
+# echo 0 > /proc/sys/net/ipv6/conf/all/autoconf
+v6names = [ int(name[8:]) for name in kvp.keys() if name.startswith("IPV6ADDR") ]
+v6names.sort()
+
+for if6_count in v6names:
+    ifname = basename
+    which = str(if6_count)
+
+    if if6_count:
+        ifname += ":" + str(if6_count)
+        which_gw = which
+    else:
+        which_gw = ""
+
+    if not ifname in autolist:
+        autolist += [ifname]
+
+    if "IPV6NETMASK" + which in kvp:
+        output += [ "iface " + ifname + " inet6 static"]
+        output += [ "\taddress " + kvp["IPV6ADDR" + which]]
+        output += [ "\tnetmask " + kvp["IPV6NETMASK" + which]]
+        if "IPV6_DEFAULTGW" + which_gw in kvp:
+            output += [ "\tgateway " + kvp["IPV6_DEFAULTGW" + which_gw] ]
+        if not dns_emitted:
+            dns_emitted = True
+            output += ["\tdns-nameservers " + ' '.join(dns)]
+        output += [""]
+
+# Mark this new interface for automatic up.
+if len(autolist):
+    output = ["auto "+" ".join(autolist)] + output
+
+print("===================================")
+print(output)
+print("===================================")
+
+
+# Time to clean out the existing interface file
+
+# Markers.
+start_mark = "# The following stanza(s) added by hv_set_ifconfig"
+end_mark = "#End of hv_set_ifconfig stanzas"
+
+f=open(if_filename,"r")
+flines=f.readlines()
+f.close()
+newfile=[]
+pitchstanza=0
+inastanza=0
+stanza=[]
+prev_line=None
+for line in flines:
+    if line.startswith("auto"):
+        if inastanza:
+            if not pitchstanza:
+                newfile.extend(stanza)
+            stanza=[]
+        inastanza=0
+        newline=""
+        autoline=line.strip().split(" ")
+        for word in autoline:
+            if (not word == basename) and (not word.startswith(basename+":")):
+                newline+=word + " "
+        newline = newline.strip()
+        if not newline == "auto":
+            newfile += [newline.strip()]
+    elif line.startswith(("iface","mapping","source")):
+        '''Read a stanza'''
+        '''A Stanza can also start with allow- ie allow-hotplug'''
+        if inastanza:
+            if not pitchstanza:
+                newfile.extend(stanza)
+            stanza=[]
+        inastanza=1
+        pitchstanza=0
+        autoline=line.strip().split(" ")
+        for word in autoline:
+            if (word == basename) or (word.startswith(basename+":")):
+                pitchstanza=1
+        if not pitchstanza:
+            stanza+=[line.strip()]
+    elif line.strip() in (start_mark, end_mark):
+        if inastanza:
+            if not pitchstanza:
+                newfile.extend(stanza)
+            stanza=[]
+        inastanza = 0
+        pitchstanza = 0
+        # Deduplicate markers.
+        if line != prev_line:
+            newfile += [line.strip()]
+    else:
+        if inastanza:
+            if not pitchstanza:
+                stanza+=[line.strip()]
+        else:
+            if not pitchstanza:
+                newfile += [line.strip()]
+    prev_line=line
+
+# Include pending stanza if any.
+if inastanza and not pitchstanza:
+    newfile.extend(stanza)
+
+
+def emit(line):
+    print(line)
+    output = line + "\n"
+    os.write(fd, output.encode('utf-8'))
+
+# Insert the new output at the end and inside the existing markers if found.
+emitted = False
+fd, path = tempfile.mkstemp()
+for line in newfile:
+    if line == end_mark:
+        emit("\n".join(output))
+        emitted = True
+    emit(line)
+if not emitted:
+    emit(start_mark)
+    emit("\n".join(output))
+    emit(end_mark)
+os.close(fd)
+
+shutil.copy(path,if_filename)
+os.chmod(if_filename,0o644)
+
+#print("TMPFILE is at: " + path)
+#print("Copied file is at: " + if_filename)
+
+try:
+    retcode = subprocess.call("ifdown "+basename , shell=True)
+    if retcode < 0:
+        print("Child was terminated by signal", -retcode, file=sys.stderr)
+    else:
+        print("Child returned", retcode, file=sys.stderr)
+except OSError as e:
+    print("Execution failed:", e, file=sys.stderr)
+
+try:
+    retcode = subprocess.call("ifup "+basename , shell=True)
+    if retcode < 0:
+        print("Child was terminated by signal", -retcode, file=sys.stderr)
+    else:
+        print("Child returned", retcode, file=sys.stderr)
+except OSError as e:
+    print("Execution failed:", e, file=sys.stderr)
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/bumpabi
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/bumpabi
@@ -0,0 +1,3 @@
+UBUNTU: Bump ABI
+
+Ignore: yes
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/config-updates
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/config-updates
@@ -0,0 +1,15 @@
+#
+# This template is used for commit messages that don't need to
+# show up in debian/changelog. Administrative stuff like config
+# updates, ABI bumps, etc. Setting 'Ignore: yes' prevents
+# 'debian/rules insertchanges' from inserting this commit meesage
+# as a changelog entry.
+#
+# Please give a one-line description of the config change followed
+# by a detailed explanation if necessary
+
+UBUNTU: [Config] XXXX
+
+# BugLink: http://bugs.launchpad.net/bugs/<enter bug# here>
+# Ignore: yes
+# Other text below here.
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/external-driver
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/external-driver
@@ -0,0 +1,20 @@
+# Ubuntu external driver commit.
+#
+# NOTE: This gets reformatted for README.Ubuntu-External-Drivers and
+# debian/changelog.
+#
+# This is only needed when a driver is added, updated or removed. It is
+# not needed when patches or fixes are applied to the driver. If the
+# driver is being removed, add the line:
+#
+# Removing: yes
+#
+# to the commit, and you can remove all other tags (except UBUNTU:).
+#
+UBUNTU: 
+
+ExternalDriver: 
+Description:
+Url:
+Mask:
+Version:
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/missing-modules
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/missing-modules
@@ -0,0 +1,3 @@
+UBUNTU: build/modules: Add modules that have intentionally gone missing
+
+Ignore: yes
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/newrelease
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/newrelease
@@ -0,0 +1,3 @@
+UBUNTU: Start new release
+
+Ignore: yes
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/sauce-patch
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/sauce-patch
@@ -0,0 +1,40 @@
+# Ubuntu commit template.
+#
+# NOTE: This gets reformatted for debian/changelog
+#
+#
+# SAUCE refers to the fact that this patch might not go upstream, but we need to
+# carry it to successive releases. In most cases you DONOT want to use this
+# template. 
+#
+# An example of a SAUCE patch is the ACPI DSDT-in-initramfs patch which has been
+# refused upstream, but still provides useful functionality to users with broken
+# BIOSes.
+#
+#-------------------------------------------------------------------------
+#
+# The initial UBUNTU is a flag that this is an Ubuntu commit. It will be
+# referenced to the Author in the debian/changelog entry.
+#
+# The text following is the short message that will be placed in the
+# changelog. Extra text on the following lines will be ignored, but left
+# in the git commit. Lines with # will be ignored in the commit.
+#
+# OriginalAuthor allows for alternate attribution.
+#
+# OriginalLocation allows for a URL or description of where the patch came
+# from.
+#
+# BugLink is a URL to a Malone bug.
+#
+# Ignore: yes will keep this commit from showing up in the changelog.
+#
+UBUNTU: SAUCE: 
+
+<Why is this patch not going upstream?>
+
+# OriginalAuthor: 
+# OriginalLocation: 
+# BugLink: http://bugs.launchpad.net/bugs/<enter bug# here>
+# Ignore: yes
+# Other text below here.
--- linux-xilinx-zynqmp-5.15.0.orig/debian/commit-templates/upstream-patch
+++ linux-xilinx-zynqmp-5.15.0/debian/commit-templates/upstream-patch
@@ -0,0 +1,27 @@
+# Ubuntu commit template.
+#
+# NOTE: This gets reformatted for debian/changelog
+#
+# The initial UBUNTU is a flag that this is an Ubuntu commit. It will be
+# referenced to the Author in the debian/changelog entry.
+#
+# The text following is the short message that will be placed in the
+# changelog. Extra text on the following lines will be ignored, but left
+# in the git commit. Lines with # will be ignored in the commit.
+#
+# OriginalAuthor allows for alternate attribution.
+#
+# OriginalLocation allows for a URL or description of where the patch came
+# from.
+#
+# BugLink is a URL to a Malone bug.
+#
+# Ignore: yes will keep this commit from showing up in the changelog.
+#
+UBUNTU: [Upstream]
+
+# OriginalAuthor: 
+# OriginalLocation: 
+# BugLink: http://bugs.launchpad.net/bugs/<enter bug# here>
+# Ignore: yes
+# Other text below here.
--- linux-xilinx-zynqmp-5.15.0.orig/debian/control
+++ linux-xilinx-zynqmp-5.15.0/debian/control
@@ -0,0 +1,246 @@
+Source: linux-xilinx-zynqmp
+Section: devel
+Priority: optional
+Maintainer: Ubuntu Kernel Team <kernel-team@lists.ubuntu.com>
+XSC-Ubuntu-Compatible-Signing: ubuntu/4 pro/3
+Standards-Version: 3.9.4.0
+Build-Depends:
+ debhelper-compat (= 10),
+ cpio,
+ kmod <!stage1>,
+ makedumpfile [amd64] <!stage1>,
+ libcap-dev <!stage1>,
+ libelf-dev <!stage1>,
+ libnewt-dev <!stage1>,
+ libiberty-dev <!stage1>,
+ default-jdk-headless <!stage1>,
+ java-common <!stage1>,
+ rsync <!stage1>,
+ libdw-dev <!stage1>,
+ libpci-dev <!stage1>,
+ pkg-config <!stage1>,
+ python3-dev <!stage1>,
+ flex <!stage1>,
+ bison <!stage1>,
+ libunwind8-dev [amd64 arm64 armhf ppc64el] <!stage1>,
+ liblzma-dev <!stage1>,
+ openssl <!stage1>,
+ libssl-dev <!stage1>,
+ libaudit-dev <!stage1>,
+ bc <!stage1>,
+ gawk <!stage1>,
+ libudev-dev <!stage1>,
+ autoconf <!stage1>,
+ automake <!stage1>,
+ libtool <!stage1>,
+ uuid-dev <!stage1>,
+ libnuma-dev [amd64 arm64 ppc64el s390x] <!stage1>,
+ dkms <!stage1>,
+ dwarfdump <!stage1>,
+ curl <!stage1>,
+ zstd [amd64 s390x] <!stage1>,
+ pahole [amd64 arm64 armhf ppc64el s390x riscv64] | dwarves (>= 1.21) [amd64 arm64 armhf ppc64el s390x riscv64] <!stage1>,
+Build-Depends-Indep:
+ xmlto <!stage1>,
+ docbook-utils <!stage1>,
+ ghostscript <!stage1>,
+ fig2dev <!stage1>,
+ bzip2 <!stage1>,
+ sharutils <!stage1>,
+ asciidoc <!stage1>,
+ python3-sphinx <!stage1>,
+ python3-sphinx-rtd-theme <!stage1>,
+ fontconfig <!stage1>,
+ python3-docutils <!stage1>,
+ imagemagick <!stage1>,
+ graphviz <!stage1>,
+ dvipng <!stage1>,
+ fonts-noto-cjk <!stage1>,
+ latexmk <!stage1>,
+ librsvg2-bin <!stage1>,
+Vcs-Git: git://git.launchpad.net/~canonical-kernel/ubuntu/+source/linux-xilinx-zynqmp/+git/jammy
+XS-Testsuite: autopkgtest
+#XS-Testsuite-Depends: gcc-4.7 binutils
+
+Package: linux-xilinx-zynqmp-headers-5.15.0-1050
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, coreutils
+Description: Header files related to Linux kernel version 5.15.0
+ This package provides kernel header files for version 5.15.0, for sites
+ that want the latest kernel headers. Please read
+ /usr/share/doc/linux-xilinx-zynqmp-headers-5.15.0-1050/debian.README.gz for details
+
+Package: linux-xilinx-zynqmp-tools-common
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, lsb-release
+Description: Linux kernel version specific tools for version 5.15.0
+ This package provides the architecture independent parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version 5.15.0.
+
+Package: linux-xilinx-zynqmp-tools-5.15.0-1050
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-tools-common
+Description: Linux kernel version specific tools for version 5.15.0-1050
+ This package provides the architecture dependant parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version 5.15.0-1050 on
+ .
+ You probably want to install linux-tools-5.15.0-1050-<flavour>.
+
+Package: linux-xilinx-zynqmp-tools-host
+Build-Profiles: <!stage1>
+Architecture: all
+Multi-Arch: foreign
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, python3
+Description: Linux kernel VM host tools
+ This package provides kernel tools useful for VM hosts.
+
+
+
+Package: linux-image-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: kernel
+Priority: optional
+Provides: linux-image, fuse-module, kvm-api-4, redhat-cluster-modules, ivtv-modules, virtualbox-guest-modules [amd64], ${linux:rprovides}
+Depends: ${misc:Depends}, ${shlibs:Depends}, kmod, linux-base (>= 4.5ubuntu1~16.04.1), linux-modules-5.15.0-1050-xilinx-zynqmp
+Recommends: grub-pc [amd64] | grub-efi-amd64 [amd64] | grub-efi-ia32 [amd64] | grub [amd64] | lilo [amd64] | flash-kernel [armhf arm64] | grub-efi-arm64 [arm64] | grub-efi-arm [armhf] | grub-ieee1275 [ppc64el], initramfs-tools | linux-initramfs-tool
+Breaks: flash-kernel (<< 3.104ubuntu20) [arm64 armhf], s390-tools (<< 2.3.0-0ubuntu3) [s390x]
+Conflicts: linux-image-unsigned-5.15.0-1050-xilinx-zynqmp
+Suggests: fdutils, linux-doc | linux-xilinx-zynqmp-source-5.15.0, linux-xilinx-zynqmp-tools, linux-headers-5.15.0-1050-xilinx-zynqmp, linux-modules-extra-5.15.0-1050-xilinx-zynqmp
+Description: Linux kernel image for version 5.15.0 on  SMP
+ This package contains the Linux kernel image for version 5.15.0 on
+  SMP.
+ .
+ Supports Xilinx ZYNQ Ultrascale+ processors.
+ .
+ Geared toward desktop and server systems.
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-xilinx-zynqmp meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-modules-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-image-5.15.0-1050-xilinx-zynqmp | linux-image-unsigned-5.15.0-1050-xilinx-zynqmp
+Built-Using: ${linux:BuiltUsing}
+Description: Linux kernel extra modules for version 5.15.0 on  SMP
+ Contains the corresponding System.map file, the modules built by the
+ packager, and scripts that try to ensure that the system is not left in an
+ unbootable state after an update.
+ .
+ Supports Xilinx ZYNQ Ultrascale+ processors.
+ .
+ Geared toward desktop and server systems.
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-xilinx-zynqmp meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-modules-extra-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}, linux-image-5.15.0-1050-xilinx-zynqmp | linux-image-unsigned-5.15.0-1050-xilinx-zynqmp, crda | wireless-crda
+Description: Linux kernel extra modules for version 5.15.0 on  SMP
+ This package contains the Linux kernel extra modules for version 5.15.0 on
+  SMP.
+ .
+ Also includes the corresponding System.map file, the modules built by the
+ packager, and scripts that try to ensure that the system is not left in an
+ unbootable state after an update.
+ .
+ Supports Xilinx ZYNQ Ultrascale+ processors.
+ .
+ Geared toward desktop and server systems.
+ .
+ You likely do not want to install this package directly. Instead, install
+ the linux-xilinx-zynqmp meta-package, which will ensure that upgrades work
+ correctly, and that supporting packages are also installed.
+
+Package: linux-headers-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, linux-xilinx-zynqmp-headers-5.15.0-1050, ${shlibs:Depends}
+Provides: linux-headers, linux-headers-3.0
+Description: Linux kernel headers for version 5.15.0 on  SMP
+ This package provides kernel header files for version 5.15.0 on
+  SMP.
+ .
+ This is for sites that want the latest kernel headers.  Please read
+ /usr/share/doc/linux-headers-5.15.0-1050/debian.README.gz for details.
+
+Package: linux-image-5.15.0-1050-xilinx-zynqmp-dbgsym
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}
+Provides: linux-debug
+Description: Linux kernel debug image for version 5.15.0 on  SMP
+ This package provides the kernel debug image for version 5.15.0 on
+  SMP.
+ .
+ This is for sites that wish to debug the kernel.
+ .
+ The kernel image contained in this package is NOT meant to boot from. It
+ is uncompressed, and unstripped. This package also includes the
+ unstripped modules.
+
+Package: linux-tools-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, linux-xilinx-zynqmp-tools-5.15.0-1050
+Description: Linux kernel version specific tools for version 5.15.0-1050
+ This package provides the architecture dependant parts for kernel
+ version locked tools (such as perf and x86_energy_perf_policy) for
+ version 5.15.0-1050 on
+ .
+
+Package: linux-cloud-tools-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: devel
+Priority: optional
+Depends: ${misc:Depends}, linux-xilinx-zynqmp-cloud-tools-5.15.0-1050
+Description: Linux kernel version specific cloud tools for version 5.15.0-1050
+ This package provides the architecture dependant parts for kernel
+ version locked tools for cloud for version 5.15.0-1050 on
+ .
+
+
+Package: linux-buildinfo-5.15.0-1050-xilinx-zynqmp
+Build-Profiles: <!stage1>
+Architecture: arm64
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}
+Built-Using: ${linux:BuiltUsing}
+Description: Linux kernel buildinfo for version 5.15.0 on  SMP
+ This package contains the Linux kernel buildinfo for version 5.15.0 on
+  SMP.
+ .
+ You likely do not want to install this package.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/control.d/flavour-buildinfo.stub
+++ linux-xilinx-zynqmp-5.15.0/debian/control.d/flavour-buildinfo.stub
@@ -0,0 +1,14 @@
+
+Package: linux-buildinfo-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Depends: ${misc:Depends}, ${shlibs:Depends}
+Built-Using: ${linux:BuiltUsing}
+Description: Linux kernel buildinfo for version PKGVER on DESC
+ This package contains the Linux kernel buildinfo for version PKGVER on
+ DESC.
+ .
+ You likely do not want to install this package.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/control.d/flavour-module.stub
+++ linux-xilinx-zynqmp-5.15.0/debian/control.d/flavour-module.stub
@@ -0,0 +1,19 @@
+
+Package: linux-modules-MODULE-PKGVER-ABINUM-FLAVOUR
+Build-Profiles: <!stage1>
+Architecture: ARCH
+Section: kernel
+Priority: optional
+Depends:
+ ${misc:Depends},
+ linux-image-PKGVER-ABINUM-FLAVOUR | linux-image-unsigned-PKGVER-ABINUM-FLAVOUR,
+Built-Using: ${linux:BuiltUsing}
+Description: Linux kernel MODULE modules for version PKGVER-ABINUM
+ This package provides the Linux kernel MODULE modules for version
+ PKGVER-ABINUM.
+ .
+ You likely do not want to install this package directly. Instead, install the
+ one of the linux-modules-MODULE-FLAVOUR* meta-packages,
+ which will ensure that upgrades work correctly, and that supporting packages are
+ also installed.
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/copyright
+++ linux-xilinx-zynqmp-5.15.0/debian/copyright
@@ -0,0 +1,29 @@
+This is the Ubuntu prepackaged version of the Linux kernel.
+Linux was written by Linus Torvalds <Linus.Torvalds@cs.Helsinki.FI>
+and others.
+
+This package was put together by the Ubuntu Kernel Team, from
+sources retrieved from upstream linux git.
+The sources may be found at most Linux ftp sites, including 
+ftp://ftp.kernel.org/pub/linux/kernel/
+
+This package is currently maintained by the
+Ubuntu Kernel Team <ubuntu-kernel@lists.ubuntu.com>
+
+Linux is copyrighted by Linus Torvalds and others.
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; version 2 dated June, 1991.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program; if not, write to the Free Software
+   Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+On Ubuntu Linux systems, the complete text of the GNU General
+Public License v2 can be found in `/usr/share/common-licenses/GPL-2'.
--- linux-xilinx-zynqmp-5.15.0.orig/debian/debian.env
+++ linux-xilinx-zynqmp-5.15.0/debian/debian.env
@@ -0,0 +1 @@
+DEBIAN=debian.zynqmp
--- linux-xilinx-zynqmp-5.15.0.orig/debian/docs/README.inclusion-list
+++ linux-xilinx-zynqmp-5.15.0/debian/docs/README.inclusion-list
@@ -0,0 +1,51 @@
+This README describes the reason for, and the use of, module
+inclusion lists.
+
+The original Hardy release had the notion of sub-flavours,
+e.g., a flavour that was constructed as a subset of an existing flavour.
+For example, the virtual flavour was extracted from the server flavour using
+a subset of the server flavour modules. However, there were some difficult
+mainteneance issues with regard to packaging, make rules, and scripts. This
+re-implementation of the sub-flavours philosophy is hopefully simpler,
+and retrofitable to all releases.
+
+A module inclusion list looks at the problem of of constructing a package
+from the perspective of what modules do we _want_ in the package, as opposed
+to what modules we _don't_ want. As the kernel matures, more and more devices are added
+which makes the problem of configuration maintenance a real pain in the ass.
+If we took the approach of disabling all of the config options that we don't want,
+then the differences between flavours will quickly become quite large, making
+it difficult to quickly compare the individual flavour configs.  Each time a
+new config option is added then we also have to make a decision about disabling in
+order to continue to keep the minimal number of modules.
+
+A module inclusion list is applied on a per-flavour basis. For example,
+debian.<BRANCH>/control.d/${flavour}.inclusion-list. For example, the
+config for virtual is very close to server and generic, but the inclusion list
+causes the virtual package to be constructed with _only_ the modules described 
+in the inclusion list.
+
+The inclusion list format is a simple bash regular expression list of files. For example,
+
+arch/*/{crypto,kernel,oprofile}
+drivers/acpi/*
+drivers/ata/ahci.ko
+
+These 3 regular expression forms are suitable for expansion by bash and as inputs to 'find'.
+See debian/scripts/module-inclusion for details.
+
+There are 2 log files created as a side effect of the application of the module
+inclusion list; $(flavour).inclusion-list.log and $(flavour).depmod.log.
+
+$(flavour).inclusion-list.log : This log is created while the inclusion list
+modules are being copied. If any are missing, then those warnings go in this log.
+While its not considered a fatal error, you should endevour to correct your inclusion
+list such that there are no missing modules.
+
+$(flavour).depmod.log : The log is created as a result of running depmod on the
+resulting set of modules. If there are missing symbols then you'll find that information
+here. Again, you should modify your inclusion list such that there are no missing
+symbols.
+
+Tim Gardner <tim.gardner@canonical.com>
+June 2, 2010
--- linux-xilinx-zynqmp-5.15.0.orig/debian/gbp.conf
+++ linux-xilinx-zynqmp-5.15.0/debian/gbp.conf
@@ -0,0 +1,2 @@
+[buildpackage]
+debian-tag = Ubuntu-%(version)s
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-fcopy-daemon.service
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-fcopy-daemon.service
@@ -0,0 +1,14 @@
+# On Azure/Hyper-V systems start the hv_fcopy_daemon
+#
+# author "Andy Whitcroft <apw@canonical.com>"
+[Unit]
+Description=Hyper-V File Copy Protocol Daemon
+ConditionVirtualization=microsoft
+ConditionPathExists=/dev/vmbus/hv_fcopy
+BindsTo=sys-devices-virtual-misc-vmbus\x21hv_fcopy.device
+
+[Service]
+ExecStart=/usr/sbin/hv_fcopy_daemon -n
+
+[Install]
+WantedBy=multi-user.target
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-fcopy-daemon.udev
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-fcopy-daemon.udev
@@ -0,0 +1 @@
+SUBSYSTEM=="misc", KERNEL=="vmbus/hv_fcopy", TAG+="systemd", ENV{SYSTEMD_WANTS}+="hv-fcopy-daemon.service"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-fcopy-daemon.upstart
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-fcopy-daemon.upstart
@@ -0,0 +1,22 @@
+# On Azure/Hyper-V systems start the hv_fcopy_daemon
+#
+description "Hyper-V File Copy Protocol Daemon"
+author "Andy Whitcroft <apw@canonical.com>"
+
+start on runlevel [2345]
+stop on runlevel [!2345]
+console log
+
+pre-start script
+        if [ -e "/etc/default/hv-kvp-daemon-init" ]; then
+                . /etc/default/hv-kvp-daemon-init
+        fi
+        [ "$RUN_FCOPY_DAEMON" -eq 0 ] && { stop; exit 0; }
+	if [ -d /sys/class/dmi/id/. ]; then
+		read company </sys/class/dmi/id/sys_vendor
+		read product </sys/class/dmi/id/product_name
+		[ "$company:$product" = 'Microsoft Corporation:Virtual Machine' ] || { stop; exit 0; }
+	fi
+end script
+
+exec /usr/sbin/hv_fcopy_daemon -n
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-kvp-daemon.service
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-kvp-daemon.service
@@ -0,0 +1,20 @@
+# On Azure/Hyper-V systems start the hv_kvp_daemon
+#
+# author "Andy Whitcroft <apw@canonical.com>"
+[Unit]
+Description=Hyper-V KVP Protocol Daemon
+ConditionVirtualization=microsoft
+ConditionKernelCommandLine=!snapd_recovery_mode
+DefaultDependencies=no
+BindsTo=sys-devices-virtual-misc-vmbus\x21hv_kvp.device
+After=sys-devices-virtual-misc-vmbus\x21hv_kvp.device systemd-remount-fs.service
+Before=shutdown.target cloud-init-local.service walinuxagent.service
+Conflicts=shutdown.target
+RequiresMountsFor=/var/lib/hyperv
+ConditionPathExists=/dev/vmbus/hv_kvp
+
+[Service]
+ExecStart=/usr/sbin/hv_kvp_daemon -n
+
+[Install]
+WantedBy=multi-user.target
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-kvp-daemon.udev
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-kvp-daemon.udev
@@ -0,0 +1 @@
+SUBSYSTEM=="misc", KERNEL=="vmbus/hv_kvp", TAG+="systemd", ENV{SYSTEMD_WANTS}+="hv-kvp-daemon.service"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-kvp-daemon.upstart
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-kvp-daemon.upstart
@@ -0,0 +1,22 @@
+# On Azure/Hyper-V systems start the hv_kvp_daemon
+#
+description "Hyper-V KVP Protocol Daemon"
+author "Adam Conrad <adconrad@canonical.com>"
+
+start on runlevel [2345]
+stop on runlevel [!2345]
+console log
+
+pre-start script
+        if [ -e "/etc/default/hv-kvp-daemon-init" ]; then
+                . /etc/default/hv-kvp-daemon-init
+        fi
+        [ "$RUN_KVP_DAEMON" = 0 ] && { stop; exit 0; }
+	if [ -d /sys/class/dmi/id/. ]; then
+		read company </sys/class/dmi/id/sys_vendor
+		read product </sys/class/dmi/id/product_name
+		[ "$company:$product" = 'Microsoft Corporation:Virtual Machine' ] || { stop; exit 0; }
+	fi
+end script
+
+exec /usr/sbin/hv_kvp_daemon -n
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-vss-daemon.service
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-vss-daemon.service
@@ -0,0 +1,14 @@
+# On Azure/Hyper-V systems start the hv_vss_daemon
+#
+# author "Andy Whitcroft <apw@canonical.com>"
+[Unit]
+Description=Hyper-V VSS Protocol Daemon
+ConditionVirtualization=microsoft
+ConditionPathExists=/dev/vmbus/hv_vss
+BindsTo=sys-devices-virtual-misc-vmbus\x21hv_vss.device
+
+[Service]
+ExecStart=/usr/sbin/hv_vss_daemon -n
+
+[Install]
+WantedBy=multi-user.target
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-vss-daemon.udev
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-vss-daemon.udev
@@ -0,0 +1 @@
+SUBSYSTEM=="misc", KERNEL=="vmbus/hv_vss", TAG+="systemd", ENV{SYSTEMD_WANTS}+="hv-vss-daemon.service"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.hv-vss-daemon.upstart
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.hv-vss-daemon.upstart
@@ -0,0 +1,22 @@
+# On Azure/Hyper-V systems start the hv_vss_daemon
+#
+description "Hyper-V VSS Protocol Daemon"
+author "Ben Howard <ben.howard@canonical.com>"
+
+start on runlevel [2345]
+stop on runlevel [!2345]
+console log
+
+pre-start script
+        if [ -e "/etc/default/hv-kvp-daemon-init" ]; then
+                . /etc/default/hv-kvp-daemon-init
+        fi
+        [ "$RUN_VSS_DAEMON" -eq 0 ] && { stop; exit 0; }
+	if [ -d /sys/class/dmi/id/. ]; then
+		read company </sys/class/dmi/id/sys_vendor
+		read product </sys/class/dmi/id/product_name
+		[ "$company:$product" = 'Microsoft Corporation:Virtual Machine' ] || { stop; exit 0; }
+	fi
+end script
+
+exec /usr/sbin/hv_vss_daemon -n
--- linux-xilinx-zynqmp-5.15.0.orig/debian/linux-cloud-tools-common.intel-sgx-load-module.service
+++ linux-xilinx-zynqmp-5.15.0/debian/linux-cloud-tools-common.intel-sgx-load-module.service
@@ -0,0 +1,13 @@
+[Unit]
+Description=Install SGX kernel module
+DefaultDependencies=false
+ConditionVirtualization=microsoft
+
+[Service]
+Type=oneshot
+RemainAfterExit=true
+ExecStart=/sbin/modprobe intel_sgx
+ExecStop=/sbin/modprobe -r intel_sgx
+
+[Install]
+WantedBy=multi-user.target
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2012-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2012-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 1 (0x1)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Apr 12 11:39:08 2012 GMT
+            Not After : Apr 11 11:39:08 2042 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:c9:5f:9b:62:8f:0b:b0:64:82:ac:be:c9:e2:62:
+                    e3:4b:d2:9f:1e:8a:d5:61:1a:2b:5d:38:f4:b7:ce:
+                    b9:9a:b8:43:b8:43:97:77:ab:4f:7f:0c:70:46:0b:
+                    fc:7f:6d:c6:6d:ea:80:5e:01:d2:b7:66:1e:87:de:
+                    0d:6d:d0:41:97:a8:a5:af:0c:63:4f:f7:7c:c2:52:
+                    cc:a0:31:a9:bb:89:5d:99:1e:46:6f:55:73:b9:76:
+                    69:ec:d7:c1:fc:21:d6:c6:07:e7:4f:bd:22:de:e4:
+                    a8:5b:2d:db:95:34:19:97:d6:28:4b:21:4c:ca:bb:
+                    1d:79:a6:17:7f:5a:f9:67:e6:5c:78:45:3d:10:6d:
+                    b0:17:59:26:11:c5:57:e3:7f:4e:82:ba:f6:2c:4e:
+                    c8:37:4d:ff:85:15:84:47:e0:ed:3b:7c:7f:bc:af:
+                    e9:01:05:a7:0c:6f:c3:e9:8d:a3:ce:be:a6:e3:cd:
+                    3c:b5:58:2c:9e:c2:03:1c:60:22:37:39:ff:41:02:
+                    c1:29:a4:65:51:ff:33:34:aa:42:15:f9:95:78:fc:
+                    2d:f5:da:8a:85:7c:82:9d:fb:37:2c:6b:a5:a8:df:
+                    7c:55:0b:80:2e:3c:b0:63:e1:cd:38:48:89:e8:14:
+                    06:0b:82:bc:fd:d4:07:68:1b:0f:3e:d9:15:dd:94:
+                    11:1b
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                61:48:2A:A2:83:0D:0A:B2:AD:5A:F1:0B:72:50:DA:90:33:DD:CE:F0
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        8f:8a:a1:06:1f:29:b7:0a:4a:d5:c5:fd:81:ab:25:ea:c0:7d:
+        e2:fc:6a:96:a0:79:93:67:ee:05:0e:25:12:25:e4:5a:f6:aa:
+        1a:f1:12:f3:05:8d:87:5e:f1:5a:5c:cb:8d:23:73:65:1d:15:
+        b9:de:22:6b:d6:49:67:c9:a3:c6:d7:62:4e:5c:b5:f9:03:83:
+        40:81:dc:87:9c:3c:3f:1c:0d:51:9f:94:65:0a:84:48:67:e4:
+        a2:f8:a6:4a:f0:e7:cd:cd:bd:94:e3:09:d2:5d:2d:16:1b:05:
+        15:0b:cb:44:b4:3e:61:42:22:c4:2a:5c:4e:c5:1d:a3:e2:e0:
+        52:b2:eb:f4:8b:2b:dc:38:39:5d:fb:88:a1:56:65:5f:2b:4f:
+        26:ff:06:78:10:12:eb:8c:5d:32:e3:c6:45:af:25:9b:a0:ff:
+        8e:ef:47:09:a3:e9:8b:37:92:92:69:76:7e:34:3b:92:05:67:
+        4e:b0:25:ed:bc:5e:5f:8f:b4:d6:ca:40:ff:e4:e2:31:23:0c:
+        85:25:ae:0c:55:01:ec:e5:47:5e:df:5b:bc:14:33:e3:c6:f5:
+        18:b6:d9:f7:dd:b3:b4:a1:31:d3:5a:5c:5d:7d:3e:bf:0a:e4:
+        e4:e8:b4:59:7d:3b:b4:8c:a3:1b:b5:20:a3:b9:3e:84:6f:8c:
+        21:00:c3:39
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2017-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2017-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 2 (0x2)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 26 21:52:11 2017 GMT
+            Not After : Sep 25 21:52:11 2047 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2017)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:ef:9f:fa:9f:19:3a:9d:38:23:91:cc:c4:f9:42:
+                    e0:f8:54:12:82:dc:97:2c:d6:5b:c1:35:eb:ff:4a:
+                    74:06:b5:9d:32:aa:7b:f3:fc:31:5a:34:3e:a1:a4:
+                    44:db:7b:6d:16:af:35:76:e0:9b:99:ad:21:11:c6:
+                    12:4b:ae:24:8f:bb:d3:b2:00:fe:c5:1d:9b:3a:1a:
+                    4a:6c:ca:fa:16:37:85:22:f9:ff:22:fc:40:e0:58:
+                    35:c1:39:27:b4:c6:42:1a:96:d8:a5:c5:95:2e:f7:
+                    c5:1e:21:6e:36:84:f7:a9:a1:e1:f1:03:08:96:65:
+                    71:f8:eb:83:cf:82:f7:9a:44:58:72:00:14:39:29:
+                    4b:e9:78:2f:65:20:b3:80:76:3b:ba:0d:2d:46:f6:
+                    37:05:e7:05:fe:bd:6c:c7:a2:65:b5:06:6e:07:24:
+                    99:a1:c1:cf:e1:0e:5e:49:41:71:17:a8:50:e7:38:
+                    99:e5:6e:b6:db:9f:63:db:56:f4:9c:7d:89:f6:d2:
+                    03:6c:99:83:e0:99:23:39:36:bd:cb:b5:26:7c:7d:
+                    b0:c6:fe:82:7c:52:ed:f9:2c:8f:79:71:3d:a9:2f:
+                    b5:aa:7e:77:a0:fd:69:f9:97:10:a8:b2:c6:7d:88:
+                    9e:a2:19:bd:31:b8:02:2d:34:4d:9d:98:60:82:ad:
+                    04:ff
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                24:2A:DE:75:AC:4A:15:E5:0D:50:C8:4B:0D:45:FF:3E:AE:70:7A:03
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        00:b2:b7:57:b5:2b:5d:16:d3:04:88:6a:d7:77:d5:0d:89:f1:
+        d2:6e:11:d1:8e:f5:62:05:c4:6a:57:df:eb:d2:86:68:f2:fd:
+        a7:37:11:3c:f4:ce:5d:fe:32:5f:31:a2:6b:3a:da:28:c2:88:
+        fa:7f:70:b5:25:99:ea:27:9a:56:6a:9d:b2:0f:14:99:e2:b7:
+        c6:39:1e:8e:a7:76:31:d9:ed:c5:05:8d:48:ae:1b:68:18:14:
+        51:a1:7d:f6:c7:df:cb:9d:eb:a4:3b:0b:ff:c2:07:c5:42:bc:
+        0d:b2:11:fa:37:17:2b:1c:b5:84:48:2d:f9:31:4a:57:49:8e:
+        61:a6:82:11:06:4c:34:ea:9c:2a:47:4d:eb:e0:26:af:da:d2:
+        c2:08:a0:37:35:7b:73:71:de:0b:c4:ba:c8:34:de:20:04:03:
+        6f:46:26:0d:b9:91:02:5b:71:76:cc:45:e4:08:d0:a6:dd:a4:
+        50:d3:d9:04:91:2b:d9:5c:34:88:fc:c2:37:fd:c6:d4:3e:57:
+        f7:6b:ba:7b:d7:02:7a:84:0c:c8:c1:19:cc:bc:fa:52:d5:7f:
+        b3:35:c4:53:5d:70:0a:f6:44:60:8d:a9:11:7a:1b:7d:ae:7b:
+        20:5a:4c:8d:44:f6:c1:a9:61:cb:dc:cb:90:37:d5:28:24:73:
+        87:d0:e0:d8
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2018-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2018-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 3 (0x3)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Oct 26 18:31:14 2018 GMT
+            Not After : Oct 24 18:31:14 2048 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (ESM 2018)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:bf:6a:e5:6d:55:7a:ec:7a:11:37:45:9c:4c:8f:
+                    6b:2d:56:d3:74:2b:32:ac:84:2d:ba:cb:cc:ec:8d:
+                    92:22:69:48:a5:d4:f6:75:11:66:2f:cb:b2:fd:9e:
+                    56:ab:e6:f1:52:8e:75:3e:50:bd:25:b3:50:fc:ef:
+                    3d:76:f3:3f:7f:03:f6:e2:a1:25:69:5c:14:98:54:
+                    bd:11:bf:e9:a5:ac:46:91:4b:1d:de:b7:18:2b:c8:
+                    22:83:15:a7:4a:00:8d:9d:e4:c0:da:f7:41:02:fd:
+                    9f:5f:79:93:56:cc:86:e1:b5:e0:39:0e:3c:a2:5b:
+                    fe:c0:56:f0:92:50:5a:2b:67:67:93:56:d7:7a:75:
+                    99:6a:25:b4:63:a8:5f:69:7e:3a:49:58:2a:a7:80:
+                    f6:5a:b4:be:b2:be:a8:8c:45:41:c9:f2:fc:76:a8:
+                    65:ef:99:29:0d:c9:9c:54:6b:0a:f0:4a:0e:61:0d:
+                    ed:99:32:af:12:e2:12:7b:9f:7b:ec:05:c4:e0:b6:
+                    d5:c3:71:28:ae:dd:0b:ba:97:ad:68:0b:76:e9:bf:
+                    e7:01:7e:64:54:39:23:85:36:c8:9d:dd:27:a1:ff:
+                    df:46:36:14:7e:cb:cc:a1:cd:49:0b:6d:c2:0c:45:
+                    99:56:58:7c:87:0d:59:9a:dc:4a:39:3b:1d:d9:15:
+                    2e:b5
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                36:51:88:C1:D3:74:D6:B0:7C:3C:8F:24:0F:8E:F7:22:43:3D:6A:8B
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        4c:0f:cd:77:60:b4:6f:53:87:f3:3c:4f:e6:81:5f:a7:1c:cc:
+        60:29:b6:34:6c:4d:08:9b:e2:d2:bd:f6:17:1a:62:79:b8:17:
+        bc:a2:60:59:fd:03:51:c3:b7:6b:de:73:b3:48:95:f5:0b:aa:
+        b6:3c:b4:34:dc:1d:0b:c4:97:62:87:e7:48:d5:8f:c9:ea:e8:
+        91:8f:2a:40:cd:b7:b3:ee:b2:98:9e:fb:37:31:29:e6:8e:2f:
+        0a:39:99:1e:c6:aa:b8:05:62:85:d3:a8:3e:60:38:98:0f:f0:
+        fe:c7:ab:01:a5:6a:a5:7f:70:a6:26:94:76:23:2f:08:89:74:
+        97:c2:2a:ca:22:3e:7a:ea:22:22:08:07:f4:bb:f6:bc:69:9c:
+        4e:44:33:e2:8e:70:17:b0:9b:cb:33:94:66:6d:ff:9a:7d:e9:
+        50:b2:e8:90:14:e4:2b:91:cb:a0:c5:2e:0e:cf:19:ef:44:ef:
+        84:f0:bd:57:9e:26:c2:63:3d:df:fc:a1:84:de:5c:d7:5f:3b:
+        fb:94:61:f0:93:89:1f:cf:c3:b2:d1:90:97:35:7d:b9:8a:ad:
+        e6:05:f0:e8:3b:a1:7c:af:2b:c4:af:18:33:2e:5e:87:db:9d:
+        80:b5:04:fd:00:d0:60:ab:ff:85:77:0f:cb:47:22:c9:b2:85:
+        a8:48:16:e2
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2019-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2019-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 4 (0x4)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 18 16:10:17 2019 GMT
+            Not After : Sep 16 16:10:17 2049 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2019)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:e6:47:d8:75:e5:87:59:26:87:83:7d:5b:7a:b8:
+                    58:3d:7c:ef:36:f8:a0:7a:b7:14:56:58:7d:01:f1:
+                    1c:3b:8c:e6:5b:03:77:7d:a0:ed:47:0a:45:e6:75:
+                    5c:de:95:38:0d:38:fa:41:79:89:56:31:87:e7:a3:
+                    9a:36:70:b6:cf:24:2f:99:26:89:08:39:0e:14:c3:
+                    35:be:02:8b:52:e1:8e:7b:0c:a6:9d:78:ff:01:60:
+                    d7:f5:c3:d5:f0:5e:dc:e4:23:09:59:72:93:d3:b5:
+                    22:af:7c:cd:e0:84:0f:af:11:2d:bc:c6:72:42:af:
+                    ea:67:63:c4:10:41:78:02:80:62:0d:43:74:b4:1c:
+                    ed:50:d7:94:f1:b0:bb:f9:57:80:e4:69:0f:83:4b:
+                    a2:e6:2c:4a:9a:e1:7d:7c:62:19:29:27:97:1f:4c:
+                    f1:85:f0:39:f5:31:9f:3a:39:0e:d4:4d:07:3a:40:
+                    55:4b:a6:6c:9d:04:89:51:2d:7c:b0:ef:40:b5:42:
+                    29:16:cc:65:73:38:62:21:f6:e3:2c:17:50:9d:74:
+                    34:4e:df:7c:4a:33:a4:bb:40:cf:d5:e5:ed:05:07:
+                    cd:4c:f9:af:7f:a6:5c:b9:f7:c5:16:45:4e:44:40:
+                    d7:85:32:de:ac:e5:75:ad:9b:d7:c0:26:33:1f:77:
+                    a5:37
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                C0:74:6F:D6:C5:DA:3A:E8:27:86:46:51:AD:66:AE:47:FE:24:B3:E8
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        aa:12:6c:d1:9d:6a:da:f0:ec:7c:17:46:3b:57:b8:d6:76:5f:
+        24:e6:06:a2:0a:55:1f:2f:d3:5e:8f:de:cf:02:f2:ff:e0:dd:
+        d3:c7:bd:75:59:aa:cd:34:f3:28:80:73:cc:28:69:e7:a2:70:
+        88:a2:c7:dc:66:f0:92:0e:ff:64:bf:30:04:54:01:1b:96:ad:
+        15:c5:61:fd:32:61:d7:5e:b5:ba:91:fd:31:fc:6b:15:df:ee:
+        22:d9:e4:1f:f3:cc:8b:0c:9f:f5:e8:f7:e2:62:3f:40:52:c9:
+        f0:f1:1c:63:fc:6c:90:e1:5b:74:03:b9:df:d1:3e:a8:ec:db:
+        2b:6e:83:6f:9f:7f:ba:b4:79:fc:3d:e7:12:2f:4a:e7:17:8c:
+        2b:77:a5:90:74:3c:bd:cf:75:83:0d:1a:95:d5:56:ef:07:9b:
+        a6:b3:31:e3:8c:97:ce:68:11:b5:7b:25:03:72:1c:ea:67:e9:
+        7c:3e:73:c7:7c:3e:fc:f5:ae:8a:b2:07:0d:15:6a:66:09:d7:
+        23:b9:5d:80:7a:26:d6:b6:22:30:aa:84:af:c0:42:e9:75:c3:
+        59:ab:a3:84:87:6b:0c:b7:ab:4e:92:69:ae:2c:82:6f:ab:01:
+        24:ab:ff:78:6d:59:85:c2:3b:23:c0:bd:0d:d8:6e:3a:29:82:
+        e1:c4:5f:db
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2021v1-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2021v1-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 6 (0x6)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 23 19:29:32 2021 GMT
+            Not After : Sep 22 19:29:32 2051 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v1)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:aa:b8:34:5b:b6:ae:44:bf:41:e1:78:11:b9:7a:
+                    c8:88:b3:b0:26:50:10:9c:98:d1:f3:98:9f:23:50:
+                    64:f6:39:dd:50:3a:23:44:53:65:fc:f3:9f:f5:a5:
+                    8b:ae:8b:df:47:9f:e9:d5:a0:92:19:f1:21:ea:cc:
+                    59:3a:74:df:45:71:bc:de:64:15:a5:f6:db:ca:71:
+                    fa:19:d4:44:0d:12:ec:47:3a:43:e2:f2:dd:8b:fe:
+                    0d:7b:dc:4d:db:53:06:22:61:e5:8b:35:49:b6:33:
+                    c4:0a:69:5f:5b:81:09:84:6b:42:33:18:09:9d:a0:
+                    35:f7:9c:1e:de:6e:de:90:69:1a:e8:32:e4:49:ad:
+                    c3:31:e9:f8:4a:a2:28:1d:db:0d:29:b6:48:0a:44:
+                    93:86:41:62:8f:73:97:60:10:8a:74:46:66:55:fe:
+                    a0:95:35:9e:ef:9f:af:11:fa:5b:a3:7c:c2:35:64:
+                    11:67:28:1e:14:0a:7d:68:61:9c:cd:c7:46:39:30:
+                    31:79:94:56:b3:45:16:9a:b5:77:66:fe:41:43:0f:
+                    00:48:6e:99:dd:0c:d4:47:2c:86:8c:50:04:61:20:
+                    dd:aa:8e:73:4f:21:b4:ee:09:4d:d3:40:01:d0:f2:
+                    a7:5b:7d:05:3d:c1:e7:65:26:aa:8c:9a:58:5a:7c:
+                    6d:6f
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                A8:D5:4B:BB:38:25:CF:B9:4F:A1:3C:9F:8A:59:4A:19:5C:10:7B:8D
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        24:25:25:7e:01:a5:c8:3d:54:8c:1b:05:73:d1:06:d8:db:d4:
+        3a:71:d5:19:9d:97:1c:85:3c:ca:38:5a:0c:25:25:39:1a:67:
+        bc:6c:9d:98:6c:f3:7d:5f:b7:40:f9:73:a0:f5:7b:40:a8:66:
+        a5:f1:53:b1:78:80:24:3f:19:50:2f:02:09:ec:a1:8a:e6:0d:
+        df:c4:ae:24:9e:69:0d:5c:dc:44:4c:38:3a:53:4e:4b:a1:4b:
+        92:9f:43:a4:9d:1e:76:33:18:1b:bf:62:e5:f5:bc:93:3c:4e:
+        21:d5:5b:20:69:11:28:c1:c5:93:b5:8e:96:1d:1b:ca:72:79:
+        24:de:67:2a:50:9d:ce:8b:41:dd:3e:82:dd:a5:04:75:54:fb:
+        35:70:98:87:b4:f3:ea:41:23:23:80:0e:99:d7:03:16:ee:7e:
+        11:e2:c8:29:ab:73:c5:6d:5c:a8:2f:32:03:9f:8e:66:d6:cb:
+        54:84:55:75:ab:9a:dd:95:fd:05:1e:11:85:37:1e:63:d2:f4:
+        7f:34:64:32:a1:63:91:91:50:39:14:1a:ea:54:78:e6:0d:04:
+        23:c7:83:51:c5:25:27:07:6c:f8:65:b7:da:95:89:76:83:cc:
+        f3:7e:06:74:d3:6c:ef:e9:17:de:29:1e:ab:5c:d7:ec:df:f1:
+        98:b8:e9:66
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2021v2-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2021v2-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 7 (0x7)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 23 19:29:42 2021 GMT
+            Not After : Sep 22 19:29:42 2051 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v2)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:ba:06:8b:ee:58:b7:8b:49:7b:53:7a:d1:df:02:
+                    e3:f2:d8:b0:8c:03:5c:f4:2d:0b:d8:18:3b:23:fa:
+                    68:b0:e8:e9:9d:dc:a2:eb:5e:d3:06:a9:28:d4:9f:
+                    14:b6:1e:1c:1d:ef:69:0e:7f:44:f2:cc:4a:f1:b1:
+                    d0:71:30:6a:50:1e:b0:d3:f8:a4:19:d0:4a:f1:e3:
+                    eb:7a:e5:57:4c:a1:fb:d1:87:b9:48:e0:55:37:52:
+                    f9:de:99:2e:95:85:36:ce:d3:1d:67:2f:14:cb:7f:
+                    05:82:75:21:b6:aa:a5:14:ac:da:4a:f4:fe:fa:5c:
+                    33:49:3d:6f:de:fd:9d:75:ba:e2:c4:02:38:b5:69:
+                    f5:ff:a8:67:4b:3a:e0:34:f6:3b:07:03:a5:7e:59:
+                    6f:3a:d2:28:a4:2f:25:ac:d8:a9:1f:59:52:5d:24:
+                    36:58:51:b5:f0:12:a8:d3:78:56:57:b1:e0:a9:df:
+                    14:05:65:7c:b5:a5:00:f0:88:39:14:44:18:85:2d:
+                    0c:28:69:7b:b9:b4:1c:47:6f:43:66:4c:22:ad:f7:
+                    f6:19:75:e1:14:2c:0d:33:3f:c1:3f:fc:73:56:b2:
+                    68:05:b5:92:03:9b:65:6b:81:80:92:35:03:9b:66:
+                    68:58:c5:66:11:b6:8c:7f:05:09:9a:45:a6:0e:5e:
+                    5f:bf
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                4C:F0:46:89:2D:6F:D3:C9:A5:B0:3F:98:D8:45:F9:08:51:DC:6A:8C
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        93:9d:49:7d:9f:3e:3e:27:79:97:d9:c2:fc:0b:f7:30:b7:f4:
+        78:b2:c9:e4:5e:42:d3:27:26:70:cf:88:96:d1:f2:ea:a0:75:
+        7e:3c:f6:b7:d2:e7:95:30:e3:a6:67:a7:ee:b9:53:8f:fd:b2:
+        cb:db:e1:98:32:be:98:79:09:46:c6:63:6a:57:87:4d:b2:26:
+        46:f6:34:5e:18:75:ca:82:80:8e:33:c2:1d:c7:76:d7:14:57:
+        ef:2e:0e:9e:58:5c:81:8e:ed:53:2c:07:46:0a:8a:fc:2f:f5:
+        b2:c8:58:f5:fa:fa:bb:f9:7d:47:13:39:f0:f2:1c:15:9c:75:
+        90:40:bd:08:04:b3:6a:de:c2:cd:34:21:7e:ba:31:48:bc:a1:
+        23:bc:ee:93:b2:62:96:27:30:86:c2:d4:f7:b4:e6:3c:71:47:
+        37:84:ff:3d:0c:1e:ec:f3:0e:da:6b:dc:64:7a:b8:c0:7e:45:
+        13:09:bf:02:b3:b7:5b:6d:09:2d:6a:4e:0b:93:94:29:4c:a6:
+        c3:c7:05:fa:69:08:04:53:3c:4c:64:c0:7e:89:00:91:1b:a6:
+        c2:d7:ea:c4:db:86:38:fe:66:03:85:7b:fc:39:24:99:4c:2a:
+        3e:10:8b:91:c3:6e:20:9d:0c:ee:51:70:b5:98:58:f3:5c:ac:
+        16:98:7b:ce
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-2021v3-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-2021v3-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 8 (0x8)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Sep 23 19:30:02 2021 GMT
+            Not After : Sep 22 19:30:02 2051 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v3)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:d6:29:96:87:ae:07:42:45:bb:65:09:b2:9b:de:
+                    5d:8e:78:61:10:d5:6d:ae:ae:26:08:6a:06:ec:4a:
+                    dd:2b:e7:1a:a9:ad:78:e3:fc:cf:8f:d1:47:bd:1e:
+                    33:d8:7a:e3:66:9b:e9:73:c1:5f:42:e2:fe:bc:c3:
+                    41:f7:cd:d7:85:d7:42:c9:ea:31:e5:47:b1:93:5b:
+                    43:2b:07:51:b8:75:08:ad:0f:e7:0d:81:38:5a:21:
+                    df:b1:43:5b:db:37:c5:ac:aa:14:3a:33:19:6a:26:
+                    e0:05:fe:cd:41:31:af:5d:a8:ab:31:77:44:fc:da:
+                    00:e2:7a:44:33:c3:a7:ed:13:54:9f:19:5d:c9:98:
+                    a2:3b:af:4d:0d:87:29:9c:90:9e:42:9e:9a:06:6a:
+                    70:27:c5:aa:f7:a2:f2:88:e0:b9:66:9a:72:a0:f6:
+                    61:7e:30:8f:14:9f:44:0d:dd:54:ae:47:c8:82:ba:
+                    d2:b2:db:6f:24:c1:f4:0a:81:07:90:47:49:5f:57:
+                    d6:3f:bf:2a:73:98:f2:f6:24:1a:74:03:d7:35:f0:
+                    42:d8:14:c5:94:27:5d:3c:49:0c:b0:f0:7a:61:1b:
+                    d7:5a:e3:a3:40:57:e9:a4:07:ee:02:a3:32:27:94:
+                    bb:f3:36:c5:5f:ef:d3:07:04:3a:80:4c:9c:0a:b7:
+                    88:9f
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                10:04:37:BB:6D:E6:E4:69:B5:81:E6:1C:D6:6B:CE:3E:F4:ED:53:AF
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        3b:37:d6:a8:8d:cd:d2:df:13:35:ac:8c:92:d6:b0:ac:d1:38:
+        a8:00:97:47:59:b8:4a:84:8c:80:a5:1d:c7:29:bf:00:66:e5:
+        10:40:26:2e:31:f5:e1:13:c0:1b:29:f3:0b:7e:2d:71:d8:db:
+        e1:32:8f:79:8e:e3:97:0c:40:a9:a0:12:c1:fc:c2:50:88:72:
+        44:c5:bc:8b:45:6e:28:fd:d2:37:d6:db:17:cf:4e:61:33:08:
+        5a:5d:08:94:73:44:e2:76:00:44:1b:b8:00:a1:86:00:64:8a:
+        f1:42:32:3c:28:11:67:7c:8b:aa:06:34:74:58:e8:b3:3a:36:
+        8d:f6:04:5d:37:f5:66:52:c9:48:b0:a7:6f:34:09:dd:60:2a:
+        86:b9:14:f1:09:f6:06:16:56:e0:51:b1:e8:75:7f:fa:37:dc:
+        e0:98:a7:69:ae:7b:1a:73:89:0d:06:67:cc:01:ef:80:31:45:
+        9e:bb:03:2a:eb:89:70:d6:19:b2:c7:ce:bc:81:df:da:c8:6f:
+        a9:4b:2d:d7:a7:e1:af:c6:e8:fb:f0:61:c9:cd:d2:91:cd:8b:
+        c2:6c:ef:e0:b6:7f:f1:c4:81:f9:bb:76:9c:26:e3:fa:a1:a0:
+        cd:5e:05:de:ee:f9:1b:5b:50:0a:8b:0f:47:e3:90:32:ac:2a:
+        e7:65:02:80
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/revoked-certs/canonical-uefi-uc2019-all.pem
+++ linux-xilinx-zynqmp-5.15.0/debian/revoked-certs/canonical-uefi-uc2019-all.pem
@@ -0,0 +1,86 @@
+Certificate:
+    Data:
+        Version: 3 (0x2)
+        Serial Number: 3 (0x3)
+        Signature Algorithm: sha256WithRSAEncryption
+        Issuer: C = GB, ST = Isle of Man, L = Douglas, O = Canonical Ltd., CN = Canonical Ltd. Master Certificate Authority
+        Validity
+            Not Before: Mar  4 10:27:14 2020 GMT
+            Not After : Mar  3 10:27:14 2050 GMT
+        Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (Ubuntu Core 2019)
+        Subject Public Key Info:
+            Public Key Algorithm: rsaEncryption
+                Public-Key: (2048 bit)
+                Modulus:
+                    00:b9:10:47:2e:75:5d:f3:10:23:bb:a0:75:d2:fa:
+                    02:2d:ff:22:df:c1:e6:cd:38:7c:36:0f:ae:74:15:
+                    6e:a5:34:52:2b:c3:a4:3a:60:d7:06:ee:1d:99:93:
+                    ff:66:91:a3:18:52:2c:8c:58:e6:b4:2f:4b:c5:fb:
+                    83:e6:f3:19:bd:1b:ca:23:ec:97:1f:d8:f1:9a:f1:
+                    04:da:da:10:04:53:4b:ec:1d:b6:26:47:7c:bb:8f:
+                    a7:0a:6e:2e:e8:91:e6:c4:bb:64:34:78:3c:fa:09:
+                    15:1c:8f:9e:eb:04:99:36:22:c6:8d:07:15:0f:b9:
+                    69:08:fa:ff:4b:45:bd:ba:2b:cd:01:0e:e7:01:23:
+                    c9:e5:7a:39:3b:91:b0:45:3c:d5:77:ba:ca:f9:29:
+                    3d:11:3f:1c:6b:5b:8e:6c:4b:3f:c9:29:05:cb:59:
+                    d6:b1:c1:c0:2d:56:88:70:27:fa:73:05:5c:c2:11:
+                    d4:27:11:f7:0b:c2:d5:68:d3:1a:cd:ed:d0:e4:10:
+                    ff:34:cb:b7:45:70:34:2c:23:53:b6:9c:30:70:b4:
+                    5c:d1:e2:64:18:82:8f:62:b1:5e:aa:0b:d4:89:f2:
+                    1c:53:c4:32:7d:ef:53:ee:9b:6e:02:ab:78:bd:25:
+                    67:8b:39:36:d8:84:3b:06:99:02:d6:75:73:4e:f2:
+                    f6:b9
+                Exponent: 65537 (0x10001)
+        X509v3 extensions:
+            X509v3 Basic Constraints: critical
+                CA:FALSE
+            X509v3 Extended Key Usage: 
+                Code Signing, 1.3.6.1.4.1.311.10.3.6
+            Netscape Comment: 
+                OpenSSL Generated Certificate
+            X509v3 Subject Key Identifier: 
+                C1:D5:7B:8F:6B:74:3F:23:EE:41:F4:F7:EE:29:2F:06:EE:CA:DF:B9
+            X509v3 Authority Key Identifier: 
+                AD:91:99:0B:C2:2A:B1:F5:17:04:8C:23:B6:65:5A:26:8E:34:5A:63
+    Signature Algorithm: sha256WithRSAEncryption
+    Signature Value:
+        2d:b5:11:a8:d2:a0:af:81:a0:18:22:18:2c:08:d0:f4:63:e8:
+        8f:9a:f4:f5:20:dd:eb:22:77:19:9a:1a:09:3d:7f:aa:7d:c9:
+        81:bc:26:98:65:94:46:30:4b:c2:51:7c:f7:21:41:63:87:31:
+        fc:a4:c9:41:28:c7:2e:2a:2e:d8:a8:75:7a:72:77:3b:1b:9f:
+        72:15:0d:0c:96:8d:8b:51:f3:ce:37:b6:ca:9f:ca:59:40:4a:
+        fc:73:7a:94:12:99:aa:c2:8d:52:ce:91:19:2e:b4:da:ff:e5:
+        2c:67:74:d9:58:47:38:2f:61:88:c5:cf:a7:48:e1:08:ba:bc:
+        ec:d5:3a:47:d9:8c:dc:c3:bc:cb:98:2b:79:7a:02:46:ef:85:
+        19:2f:03:4b:05:84:eb:56:98:5f:6d:cf:a5:8b:a2:b6:e5:50:
+        51:7c:33:44:bd:7a:94:2e:0d:90:39:39:3e:62:60:ae:3a:e2:
+        f5:17:fa:f1:94:06:1d:ae:a3:f8:19:20:7f:4b:4c:07:c4:e6:
+        2d:0d:e5:94:84:51:6d:6f:0f:c4:c6:79:1d:f0:e8:0e:23:9e:
+        fd:f9:46:2c:b9:ec:97:38:56:7e:b8:13:f6:d2:e1:8e:a5:93:
+        02:7b:6e:dd:33:9a:bf:10:a8:1b:3d:fa:c4:f2:15:f0:27:73:
+        26:a6:94:d1
+-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
--- linux-xilinx-zynqmp-5.15.0.orig/debian/rules
+++ linux-xilinx-zynqmp-5.15.0/debian/rules
@@ -0,0 +1,231 @@
+#!/usr/bin/make -f
+#
+# $(DEBIAN)/rules for Ubuntu linux
+#
+# Use this however you want, just give credit where credit is due.
+#
+# Copyright (c) 2007 Ben Collins <bcollins@ubuntu.com>
+#
+
+DEBIAN=$(shell awk -F= '($$1 == "DEBIAN") { print $$2 }' <debian/debian.env)
+
+# dpkg-buildpackage passes options that are incomptatible
+# with the kernel build.
+unexport CFLAGS
+unexport LDFLAGS
+
+export LC_ALL=C
+export SHELL=/bin/bash -e
+
+# Where do we find the common configuration.
+export DROOT=debian
+
+# Common variables for all architectures
+include $(DROOT)/rules.d/0-common-vars.mk
+
+# Pull in some arch specific stuff
+-include $(DEBIAN)/rules.d/$(arch).mk
+
+# Pull in some branch specific stuff. Used by LTS backport
+# branches to override master branch settings such as do_tools_common.
+-include $(DEBIAN)/rules.d/hooks.mk
+
+# Maintainer targets
+include $(DROOT)/rules.d/1-maintainer.mk
+
+do_linux_tools=$(sort $(filter-out false,$(do_tools_usbip) $(do_tools_cpupower) $(do_tools_perf) $(do_tools_bpftool) $(do_tools_x86)))
+do_cloud_tools=$(sort $(filter-out false,$(do_tools_hyperv)))
+do_tools_common?=true
+do_tools_host?=false
+do_tools_perf_jvmti?=false
+do_enforce_all?=false
+
+# Default settings for DKMS modules.
+$(foreach _m,$(all_dkms_modules), \
+  $(eval do_$(_m) ?= $(if $(filter $(_m),$(filter-out $(dkms_exclude),$(dkms_include) $(subst any,$(_m),$(subst $(arch),$(_m),$(dkms_$(_m)_archs))))),true,false)) \
+)
+
+# Don't build tools in a cross compile environment.
+ifneq ($(DEB_HOST_ARCH),$(DEB_BUILD_ARCH))
+	do_tools=false
+$(foreach _m,$(all_dkms_modules),$(eval do_$(_m) = false))
+endif
+
+# Are any of the kernel signing options enabled.
+any_signed=$(sort $(filter-out false,$(uefi_signed) $(opal_signed) $(sipl_signed)))
+ifeq ($(any_signed),true)
+bin_pkg_name=$(bin_pkg_name_unsigned)
+else
+bin_pkg_name=$(bin_pkg_name_signed)
+endif
+
+# Stages -- support both DEB_STAGE=stage1 and DEB_BUILD_PROFILE=bootstrap
+ifeq ($(DEB_STAGE),stage1)
+    DEB_BUILD_PROFILES=stage1
+endif
+ifneq ($(DEB_BUILD_PROFILE),)
+    DEB_BUILD_PROFILES=$(DEB_BUILD_PROFILE)
+endif
+ifneq ($(filter stage1,$(DEB_BUILD_PROFILES)),)
+    do_tools=false
+    do_doc_package=false
+    do_source_package=false
+    do_flavour_image_package=false
+    do_flavour_header_package=false
+endif
+
+# autopkgtest -- rebuild support
+#  - only build the first flavour on the assumption it is representative
+#  - disable dkms builds as the versions used may have been deleted
+ifneq ($(filter autopkgtest,$(DEB_BUILD_PROFILES)),)
+	flavours := $(firstword $(flavours))
+$(foreach _m,$(all_dkms_modules),$(eval do_$(_m) = false))
+endif
+
+# Being used to build a mainline build -- turn off things which do not work.
+ifeq ($(do_mainline_build),true)
+	do_extras_package=false
+	do_tools=false
+	no_dumpfile=1
+$(foreach _m,$(all_dkms_modules),$(eval do_$(_m) = false))
+	skipabi=true
+	skipmodule=true
+	skipretpoline=true
+endif
+
+# Disable tools build and packaging if do_tools != true
+ifneq ($(do_tools),true)
+	do_linux_tools=
+	do_cloud_tools=
+	do_tools_common=
+	do_tools_host=
+endif
+
+ifeq ($(do_dkms_wireguard),false)
+	do_wireguard_disable:=$(shell for m in $$(cat $(DROOT)/wireguard-modules.ignore); do grep -qxF $$m $(prev_abidir)/../modules.ignore 2>/dev/null || echo $$m >> $(prev_abidir)/../modules.ignore; done)
+endif
+
+# Either tools package needs the common source preparation
+do_any_tools=$(sort $(filter-out false,$(do_linux_tools) $(do_cloud_tools)))
+
+# NVIDIA DKMS package gross series split into desktop and server.
+nvidia_desktop_series=$(shell sed -n -e 's/^nvidia-graphics-drivers-\([0-9][0-9]*\) .*/\1/p' $(DEBIAN)/dkms-versions)
+nvidia_server_series=$(shell sed -n -e 's/^nvidia-graphics-drivers-\([0-9][0-9]*-server\) .*/\1/p' $(DEBIAN)/dkms-versions)
+
+# Debian Build System targets
+binary: binary-indep binary-arch
+
+build: build-arch build-indep
+
+clean: debian/control debian/canonical-certs.pem debian/canonical-revoked-certs.pem
+	dh_testdir
+	dh_testroot
+	dh_clean
+
+	# normal build junk
+	rm -rf $(DEBIAN)/abi
+	rm -rf $(builddir)
+	rm -f $(stampdir)/stamp-*
+	rm -rf $(DEBIAN)/linux-*
+
+	cp $(DEBIAN)/changelog debian/changelog
+
+	# Install the copyright information.
+	cp $(DEBIAN)/copyright debian/copyright
+
+	# Install the retpoline extractor.
+	cp $(DROOT)/scripts/retpoline-extract-one scripts/ubuntu-retpoline-extract-one
+
+	# If we have a reconstruct script use it.
+	[ -f $(DEBIAN)/reconstruct ] && bash $(DEBIAN)/reconstruct || true
+
+	# Remove generated intermediate files
+	rm -f $(DROOT)/control.stub $(DEBIAN)/control.stub
+	rm -f $(DROOT)/scripts/fix-filenames
+
+distclean: clean
+	rm -rf $(DROOT)/control debian/changelog \
+		debian/control debian/control.stub debian/copyright \
+		scripts/ubuntu-retpoline-extract-one
+
+# Builds the image, arch headers and debug packages
+include $(DROOT)/rules.d/2-binary-arch.mk
+
+# Builds the source, doc and linux-headers indep packages
+include $(DROOT)/rules.d/3-binary-indep.mk
+
+# Various checks to be performed on builds
+include $(DROOT)/rules.d/4-checks.mk
+
+control_files := $(DEBIAN)/control.stub.in
+ifeq ($(do_libc_dev_package),true)
+ifneq (,$(wildcard $(DEBIAN)/control.d/linux-libc-dev.stub))
+	control_files += $(DEBIAN)/control.d/linux-libc-dev.stub
+endif
+endif
+ifeq ($(do_doc_package),true)
+ifneq (,$(wildcard $(DEBIAN)/control.d/linux-doc.stub))
+	control_files += $(DEBIAN)/control.d/linux-doc.stub
+endif
+endif
+
+# Calculate Ubuntu Compatible Signing levels
+UBUNTU_COMPATIBLE_SIGNING=$(shell grep -qx ' *Subject: C = GB, ST = Isle of Man, O = Canonical Ltd., OU = Secure Boot, CN = Canonical Ltd. Secure Boot Signing (2021 v3)' debian/canonical-revoked-certs.pem && echo ubuntu/4 pro/3)
+
+# Misc stuff
+.PHONY: $(DEBIAN)/control.stub
+$(DEBIAN)/control.stub: 				\
+		$(DROOT)/scripts/control-create		\
+		$(control_files)			\
+		debian/canonical-revoked-certs.pem	\
+		$(DROOT)/control.d/flavour-module.stub	\
+		$(DEBIAN)/changelog			\
+		$(wildcard $(DEBIAN)/control.d/* $(DEBIAN)/sub-flavours/*.vars)
+	for i in $(control_files); do                                           \
+	  cat $$i;                                                              \
+	  echo "";                                                              \
+	done | sed -e 's/PKGVER/$(release)/g'                                   \
+	        -e 's/ABINUM/$(abinum)/g'                                       \
+		-e 's/SRCPKGNAME/$(src_pkg_name)/g'                             \
+		-e 's/=HUMAN=/$(human_arch)/g'                                  \
+		-e 's/=SERIES=/$(series)/g'                                     \
+		-e 's|\(^Maintainer:.*\)|\1\nXSC-Ubuntu-Compatible-Signing: $(UBUNTU_COMPATIBLE_SIGNING)|g' \
+	  > $(DEBIAN)/control.stub;
+	flavours="$(sort $(wildcard $(DEBIAN)/control.d/vars.* $(DEBIAN)/sub-flavours/*.vars))";\
+	for i in $$flavours; do							\
+	  $(SHELL) $(DROOT)/scripts/control-create $$i "$(any_signed)" |	\
+		sed -e 's/PKGVER/$(release)/g'                                  \
+		-e 's/ABINUM/$(abinum)/g'                                       \
+		-e 's/SRCPKGNAME/$(src_pkg_name)/g'                             \
+		-e 's/=HUMAN=/$(human_arch)/g'                                  \
+		-e 's/=SERIES=/$(series)/g'                                     \
+		>> $(DEBIAN)/control.stub;                                      \
+	done
+
+.PHONY: debian/control
+debian/control: $(DEBIAN)/control.stub
+	cp $(DEBIAN)/control.stub debian/control
+
+debian/canonical-certs.pem: $(wildcard $(DROOT)/certs/*-all.pem) $(wildcard $(DROOT)/certs/*-$(arch).pem) $(wildcard $(DEBIAN)/certs/*-all.pem) $(wildcard $(DEBIAN)/certs/*-$(arch).pem)
+	for cert in $(sort $(notdir $^));					\
+	do									\
+		for dir in $(DEBIAN) $(DROOT);					\
+		do								\
+			if [ -f "$$dir/certs/$$cert" ]; then			\
+				cat "$$dir/certs/$$cert";			\
+				break;						\
+			fi;							\
+		done;								\
+	done >"$@"
+
+debian/canonical-revoked-certs.pem: $(wildcard $(DROOT)/revoked-certs/*-all.pem) $(wildcard $(DROOT)/revoked-certs/*-$(arch).pem) $(wildcard $(DEBIAN)/revoked-certs/*-all.pem) $(wildcard $(DEBIAN)/revoked-certs/*-$(arch).pem)
+	for cert in $(sort $(notdir $^));					\
+	do									\
+		for dir in $(DEBIAN) $(DROOT);					\
+		do								\
+			if [ -f "$$dir/revoked-certs/$$cert" ]; then		\
+				cat "$$dir/revoked-certs/$$cert";		\
+				break;						\
+			fi;							\
+		done;								\
+	done >"$@"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/rules.d/0-common-vars.mk
+++ linux-xilinx-zynqmp-5.15.0/debian/rules.d/0-common-vars.mk
@@ -0,0 +1,330 @@
+# Used when you need to 'escape' a comma.
+comma = ,
+
+#
+# The source package name will be the first token from $(DEBIAN)/changelog
+#
+src_pkg_name=$(shell sed -n '1s/^\(.*\) (.*).*$$/\1/p' $(DEBIAN)/changelog)
+
+# Get the series
+series=$(shell dpkg-parsechangelog -l$(DEBIAN)/changelog | sed -ne 's/^Distribution: *//p' | sed -e 's/-\(security\|updates\|proposed\)$$//')
+
+# Get some version info
+release := $(shell sed -n '1s/^$(src_pkg_name).*(\(.*\)-.*).*$$/\1/p' $(DEBIAN)/changelog)
+revisions := $(shell sed -n 's/^$(src_pkg_name)\ .*($(release)-\(.*\)).*$$/\1/p' $(DEBIAN)/changelog | tac)
+revision ?= $(word $(words $(revisions)),$(revisions))
+prev_revisions := $(filter-out $(revision),0.0 $(revisions))
+ifneq (,$(prev_revisions))
+prev_revision := $(word $(words $(prev_revisions)),$(prev_revisions))
+endif
+
+prev_fullver ?= $(shell dpkg-parsechangelog -l$(DEBIAN)/changelog -o1 -c1 | sed -ne 's/^Version: *//p')
+
+# Get variants. Assume primary if debian/variants is not present.
+variants = --
+ifneq (,$(wildcard $(DEBIAN)/variants))
+	variants := $(shell cat $(DEBIAN)/variants)
+endif
+
+# Get upstream version info
+upstream_version := $(shell sed -n 's/^VERSION = \(.*\)$$/\1/p' Makefile)
+upstream_patchlevel := $(shell sed -n 's/^PATCHLEVEL = \(.*\)$$/\1/p' Makefile)
+upstream_tag := "v$(upstream_version).$(upstream_patchlevel)"
+
+family=ubuntu
+
+# This is an internally used mechanism for the daily kernel builds. It
+# creates packages whose ABI is suffixed with a minimal representation of
+# the current git HEAD sha. If .git/HEAD is not present, then it uses the
+# uuidgen program,
+#
+# AUTOBUILD can also be used by anyone wanting to build a custom kernel
+# image, or rebuild the entire set of Ubuntu packages using custom patches
+# or configs.
+AUTOBUILD=
+
+ifneq ($(AUTOBUILD),)
+skipabi		= true
+skipmodule	= true
+skipretpoline	= true
+skipdbg		= true
+gitver=$(shell if test -f .git/HEAD; then cat .git/HEAD; else uuidgen; fi)
+gitverpre=$(shell echo $(gitver) | cut -b -3)
+gitverpost=$(shell echo $(gitver) | cut -b 38-40)
+abi_suffix = -$(gitverpre)$(gitverpost)
+endif
+
+ifneq ($(NOKERNLOG),)
+ubuntu_log_opts += --no-kern-log
+endif
+ifneq ($(PRINTSHAS),)
+ubuntu_log_opts += --print-shas
+endif
+
+# Get the kernels own extra version to be added to the release signature.
+raw_kernelversion=$(shell make kernelversion)
+
+#
+# full_build -- are we doing a full buildd style build
+#
+ifeq ($(wildcard /CurrentlyBuilding),)
+full_build?=false
+else
+full_build?=true
+endif
+
+#
+# The debug packages are ginormous, so you probably want to skip
+# building them (as a developer).
+#
+ifeq ($(full_build),false)
+skipdbg=true
+endif
+
+abinum		:= $(shell echo $(revision) | sed -r -e 's/([^\+~]*)\.[^\.]+(~.*)?(\+.*)?$$/\1/')$(abi_suffix)
+prev_abinum	:= $(shell echo $(prev_revision) | sed -r -e 's/([^\+~]*)\.[^\.]+(~.*)?(\+.*)?$$/\1/')$(abi_suffix)
+abi_release	:= $(release)-$(abinum)
+
+uploadnum	:= $(shell echo $(revision) | sed -r -e 's/[^\+~]*\.([^\.~]+(~.*)?(\+.*)?$$)/\1/')
+ifneq ($(full_build),false)
+  uploadnum	:= $(uploadnum)-Ubuntu
+endif
+
+# XXX: linux-libc-dev got bumped to -803.N inadvertantly by a ti-omap4 upload
+#      shift our version higher for this package only.  Ensure this only
+#      occurs for the v2.6.35 kernel so that we do not propogate this into
+#      any other series.
+raw_uploadnum	:= $(shell echo $(revision) | sed -e 's/.*\.//')
+libc_dev_version :=
+ifeq ($(DEBIAN),debian.master)
+ifeq ($(release),2.6.35)
+libc_dev_version := -v$(release)-$(shell expr "$(abinum)" + 1000).$(raw_uploadnum)
+endif
+endif
+
+DEB_HOST_MULTIARCH = $(shell dpkg-architecture -qDEB_HOST_MULTIARCH)
+DEB_HOST_GNU_TYPE  = $(shell dpkg-architecture -qDEB_HOST_GNU_TYPE)
+DEB_BUILD_GNU_TYPE = $(shell dpkg-architecture -qDEB_BUILD_GNU_TYPE)
+DEB_HOST_ARCH = $(shell dpkg-architecture -qDEB_HOST_ARCH)
+DEB_BUILD_ARCH = $(shell dpkg-architecture -qDEB_BUILD_ARCH)
+
+#
+# Detect invocations of the form 'fakeroot debian/rules binary arch=armhf'
+# within an x86'en schroot. This only gets you part of the way since the
+# packaging phase fails, but you can at least compile the kernel quickly.
+#
+arch := $(DEB_HOST_ARCH)
+ifneq ($(arch),$(DEB_HOST_ARCH))
+	CROSS_COMPILE ?= $(shell dpkg-architecture -a$(arch) -qDEB_HOST_GNU_TYPE -f 2>/dev/null)-
+endif
+
+#
+# Detect invocations of the form 'dpkg-buildpackage -B -aarmhf' within
+# an x86'en schroot. This is the only way to build all of the packages
+# (except for tools).
+#
+ifneq ($(DEB_BUILD_GNU_TYPE),$(DEB_HOST_GNU_TYPE))
+	CROSS_COMPILE ?= $(DEB_HOST_GNU_TYPE)-
+endif
+
+abidir		:= $(CURDIR)/$(DEBIAN)/__abi.current/$(arch)
+commonconfdir	:= $(CURDIR)/$(DEBIAN)/config
+archconfdir	:= $(CURDIR)/$(DEBIAN)/config/$(arch)
+sharedconfdir	:= $(CURDIR)/debian.master/config
+builddir	:= $(CURDIR)/debian/build
+stampdir	:= $(CURDIR)/debian/stamps
+
+#
+# The binary package name always starts with linux-image-$KVER-$ABI.$UPLOAD_NUM. There
+# are places that you'll find linux-image hard coded, but I guess thats OK since the
+# assumption that the binary package always starts with linux-image will never change.
+#
+bin_pkg_name_signed=linux-image-$(abi_release)
+bin_pkg_name_unsigned=linux-image-unsigned-$(abi_release)
+mods_pkg_name=linux-modules-$(abi_release)
+mods_extra_pkg_name=linux-modules-extra-$(abi_release)
+bldinfo_pkg_name=linux-buildinfo-$(abi_release)
+hdrs_pkg_name=linux-headers-$(abi_release)
+indep_hdrs_pkg_name=$(src_pkg_name)-headers-$(abi_release)
+
+#
+# The generation of content in the doc package depends on both 'AUTOBUILD=' and
+# 'do_doc_package_content=true'. There are usually build errors during the development
+# cycle, so its OK to leave 'do_doc_package_content=false' until those build
+# failures get sorted out. Finally, the doc package doesn't really need to be built
+# for developer testing (its kind of slow), so only do it if on a buildd.
+ifneq ($(filter --,$(variants)),)
+do_doc_package=true
+else
+do_doc_package=false
+endif
+do_doc_package_content=false
+ifeq ($(full_build),false)
+do_doc_package_content=false
+endif
+doc_pkg_name=$(src_pkg_name)-doc
+
+#
+# Similarly with the linux-source package, you need not build it as a developer. Its
+# somewhat I/O intensive and utterly useless.
+#
+do_source_package=true
+do_source_package_content=true
+ifeq ($(full_build),false)
+do_source_package_content=false
+endif
+
+# linux-libc-dev may not be needed, default to building it only for the
+# primary variant
+ifneq ($(filter --,$(variants)),)
+do_libc_dev_package=true
+else
+do_libc_dev_package=false
+endif
+
+# common headers normally is built as an indep package, but may be arch
+do_common_headers_indep=true
+
+# add a 'full source' mode
+do_full_source=false
+
+# Add an option to enable special drivers which should only be build when
+# explicitly enabled.
+do_odm_drivers=false
+
+# build tools
+ifneq ($(wildcard $(CURDIR)/tools),)
+	ifeq ($(do_tools),)
+		ifneq ($(DEB_BUILD_GNU_TYPE),$(DEB_HOST_GNU_TYPE))
+			do_tools=false
+		endif
+	endif
+	do_tools?=true
+else
+	do_tools?=false
+endif
+tools_pkg_name=$(src_pkg_name)-tools-$(abi_release)
+tools_common_pkg_name=$(src_pkg_name)-tools-common
+tools_flavour_pkg_name=linux-tools-$(abi_release)
+cloud_pkg_name=$(src_pkg_name)-cloud-tools-$(abi_release)
+cloud_common_pkg_name=$(src_pkg_name)-cloud-tools-common
+cloud_flavour_pkg_name=linux-cloud-tools-$(abi_release)
+hosttools_pkg_name=$(src_pkg_name)-tools-host
+
+# The general flavour specific image package.
+do_flavour_image_package=true
+
+# The general flavour specific header package.
+do_flavour_header_package=true
+
+# DTBs
+do_dtbs=false
+
+# Support parallel=<n> in DEB_BUILD_OPTIONS (see #209008)
+#
+# These 2 environment variables set the -j value of the kernel build. For example,
+# CONCURRENCY_LEVEL=16 fakeroot $(DEBIAN)/rules binary-debs
+# or
+# DEB_BUILD_OPTIONS=parallel=16 fakeroot $(DEBIAN)/rules binary-debs
+#
+# The default is to use the number of CPUs.
+#
+COMMA=,
+DEB_BUILD_OPTIONS_PARA = $(subst parallel=,,$(filter parallel=%,$(subst $(COMMA), ,$(DEB_BUILD_OPTIONS))))
+ifneq (,$(DEB_BUILD_OPTIONS_PARA))
+  CONCURRENCY_LEVEL := $(DEB_BUILD_OPTIONS_PARA)
+endif
+
+ifeq ($(CONCURRENCY_LEVEL),)
+  # Check the environment
+  CONCURRENCY_LEVEL := $(shell echo $$CONCURRENCY_LEVEL)
+  # No? Then build with the number of CPUs on the host.
+  ifeq ($(CONCURRENCY_LEVEL),)
+      CONCURRENCY_LEVEL := $(shell expr `getconf _NPROCESSORS_ONLN` \* 1)
+  endif
+  # Oh hell, give 'em one
+  ifeq ($(CONCURRENCY_LEVEL),)
+    CONCURRENCY_LEVEL := 1
+  endif
+endif
+
+conc_level		= -j$(CONCURRENCY_LEVEL)
+
+PYTHON ?= $(firstword $(wildcard /usr/bin/python3) $(wildcard /usr/bin/python2) $(wildcard /usr/bin/python))
+
+# target_flavour is filled in for each step
+kmake = make ARCH=$(build_arch) \
+	CROSS_COMPILE=$(CROSS_COMPILE) \
+	KERNELVERSION=$(abi_release)-$(target_flavour) \
+	CONFIG_DEBUG_SECTION_MISMATCH=y \
+	KBUILD_BUILD_VERSION="$(uploadnum)" \
+	LOCALVERSION= localver-extra= \
+	CFLAGS_MODULE="-DPKG_ABI=$(abinum)" \
+	PYTHON=$(PYTHON)
+ifneq ($(LOCAL_ENV_CC),)
+kmake += CC="$(LOCAL_ENV_CC)" DISTCC_HOSTS="$(LOCAL_ENV_DISTCC_HOSTS)"
+endif
+
+# Locking is required in parallel builds to prevent loss of contents
+# of the debian/files.
+lockme_file = $(CURDIR)/debian/.LOCK
+lockme_cmd = flock -w 60
+lockme = $(lockme_cmd) $(lockme_file)
+
+# Don't fail if a link already exists.
+LN = ln -sf
+
+# Checks if a var is overriden by the custom rules. Called with var and
+# flavour as arguments.
+custom_override = \
+ $(shell if [ -n "$($(1)_$(2))" ]; then echo "$($(1)_$(2))"; else echo "$($(1))"; fi)
+
+# selftests that Ubuntu cares about
+ubuntu_selftests = breakpoints cpu-hotplug efivarfs memfd memory-hotplug mount net ptrace seccomp timers powerpc user ftrace
+
+# DKMS
+all_dkms_modules =
+
+subst_paired = $(subst $(firstword $(subst =, ,$(1))),$(lastword $(subst =, ,$(1))),$(2))
+recursive_call = $(if $(2),$(call recursive_call,$(1),$(wordlist 2,$(words $(2)),$(2)),$(call $(1),$(firstword $(2)),$(3))),$(3))
+
+$(foreach _line,$(shell gawk '{ OFS = "!"; $$1 = $$1; print }' $(DEBIAN)/dkms-versions), \
+  $(eval _params = $(subst !, ,$(_line))) \
+  $(eval _deb_pkgname = $(firstword $(_params))) \
+  $(eval _deb_version = $(word 2,$(_params))) \
+  $(if $(filter modulename=%,$(_params)), \
+    $(eval _m = $(word 2,$(subst =, ,$(filter modulename=%,$(_params))))) \
+    , \
+    $(info modulename for $(_deb_pkgname) not specified in dkms-versions. Assume $(_deb_pkgname).) \
+    $(eval _m = $(_deb_pkgname)) \
+  ) \
+  $(eval all_dkms_modules += $(_m)) \
+  $(eval dkms_$(_m)_version = $(_deb_version)) \
+  $(foreach _p,$(patsubst debpath=%,%,$(filter debpath=%,$(_params))), \
+    $(eval dkms_$(_m)_debpath += $(strip \
+      $(call recursive_call,subst_paired, \
+        %module%=$(_m) \
+        %package%=$(_deb_pkgname) \
+        %version%=$(lastword $(subst :, ,$(_deb_version))) \
+        , \
+        $(_p) \
+      ) \
+    )) \
+  ) \
+  $(if $(dkms_$(_m)_debpath),,$(error debpath for $(_deb_pkgname) not specified.)) \
+  $(if $(filter arch=%,$(_params)), \
+    $(eval dkms_$(_m)_archs = $(patsubst arch=%,%,$(filter arch=%,$(_params)))) \
+    , \
+    $(eval dkms_$(_m)_archs = any) \
+  ) \
+  $(eval dkms_$(_m)_rprovides = $(patsubst rprovides=%,%,$(filter rprovides=%,$(_params)))) \
+  $(eval dkms_$(_m)_type = $(word 1,$(patsubst type=%,%,$(filter type=%,$(_params))) built-in)) \
+  $(eval all_$(dkms_$(_m)_type)_dkms_modules += $(_m)) \
+  $(if $(filter standalone,$(dkms_$(_m)_type)), \
+    $(eval dkms_$(_m)_pkg_name = linux-modules-$(_m)-$(abi_release)) \
+    $(eval dkms_$(_m)_subdir = ubuntu) \
+    , \
+    $(eval dkms_$(_m)_pkg_name = $(mods_pkg_name)) \
+    $(eval dkms_$(_m)_subdir = kernel) \
+  ) \
+)
--- linux-xilinx-zynqmp-5.15.0.orig/debian/rules.d/1-maintainer.mk
+++ linux-xilinx-zynqmp-5.15.0/debian/rules.d/1-maintainer.mk
@@ -0,0 +1,192 @@
+# The following targets are for the maintainer only! do not run if you don't
+# know what they do.
+
+.PHONY: printenv updateconfigs migrateconfigs printchanges insertchanges startnewrelease diffupstream help autoreconstruct finalchecks
+
+help:
+	@echo "These are the targets in addition to the normal $(DEBIAN) ones:"
+	@echo
+	@echo "  printenv        : Print some variables used in the build"
+	@echo
+	@echo "  updateconfigs        : Update core arch configs"
+	@echo
+	@echo "  editconfigs          : Update core arch configs interractively"
+	@echo "  migrateconfigs       : Automatically import old configs into annotations"
+	@echo "  genconfigs           : Generate core arch configs in CONFIGS/*"
+	@echo
+	@echo "  printchanges    : Print the current changelog entries (from git)"
+	@echo
+	@echo "  insertchanges   : Insert current changelog entries (from git)"
+	@echo
+	@echo "  startnewrelease : Start a new changelog set"
+	@echo
+	@echo "  diffupstream    : Diff stock kernel code against upstream (git)"
+	@echo
+	@echo "  compileselftests : Only compile the selftests listed on ubuntu_selftests variable"
+	@echo
+	@echo "  runselftests    : Run the selftests listed on ubuntu_selftests variable"
+	@echo
+	@echo "  help            : If you are kernel hacking, you need the professional"
+	@echo "                    version of this"
+	@echo
+	@echo "Environment variables:"
+	@echo
+	@echo "  NOKERNLOG       : Do not add upstream kernel commits to changelog"
+	@echo "  CONCURRENCY_LEVEL=X"
+	@echo "                  : Use -jX for kernel compile"
+	@echo "  PRINTSHAS       : Include SHAs for commits in changelog"
+
+printdebian:
+	@echo "$(DEBIAN)"
+
+updateconfigs defaultconfigs editconfigs genconfigs dumpconfigs:
+	dh_testdir;
+ifneq ($(wildcard $(DEBIAN)/config/config.common.ubuntu),)
+	$(SHELL) $(DROOT)/scripts/misc/old-kernelconfig $@ "$(do_enforce_all)"
+else
+	kmake='$(kmake)' skip_checks=$(do_skip_checks) conc_level=$(conc_level) \
+		$(SHELL) $(DROOT)/scripts/misc/kernelconfig $@
+	@rm -rf build
+endif
+
+migrateconfigs:
+ifneq ($(wildcard $(DEBIAN)/config/config.common.ubuntu),)
+	dh_testdir
+	conc_level=$(conc_level) $(SHELL) $(DROOT)/scripts/misc/old-kernelconfig genconfigs
+	rm -rf build
+	mkdir build
+	mv $(DEBIAN)/config/annotations build/.annotations
+	mv $(DEBIAN)/config/README.rst build/.README.rst 2>/dev/null || true
+	rm -rf $(DEBIAN)/config
+	mkdir -p $(DEBIAN)/config
+	debian/scripts/misc/migrate-annotations < build/.annotations > $(DEBIAN)/config/annotations
+	mv build/.README.rst $(DEBIAN)/config/README.rst 2>/dev/null || true
+	rm -rf build
+	kmake='$(kmake)' conc_level=$(conc_level) $(SHELL) $(DROOT)/scripts/misc/kernelconfig updateconfigs
+endif
+
+printenv:
+	dh_testdir
+	@echo "src package name  = $(src_pkg_name)"
+	@echo "series            = $(series)"
+	@echo "release           = $(release)"
+	@echo "revisions         = $(revisions)"
+	@echo "revision          = $(revision)"
+	@echo "uploadnum         = $(uploadnum)"
+	@echo "prev_revisions    = $(prev_revisions)"
+	@echo "prev_revision     = $(prev_revision)"
+	@echo "abinum            = $(abinum)"
+	@echo "upstream_tag      = $(upstream_tag)"
+	@echo "gitver            = $(gitver)"
+	@echo "variants          = $(variants)"
+	@echo "flavours          = $(flavours)"
+	@echo "skipabi           = $(skipabi)"
+	@echo "skipmodule        = $(skipmodule)"
+	@echo "skipdbg           = $(skipdbg)"
+	@echo "ubuntu_log_opts   = $(ubuntu_log_opts)"
+	@echo "CONCURRENCY_LEVEL = $(CONCURRENCY_LEVEL)"
+	@echo "ubuntu_selftests  = $(ubuntu_selftests)"
+	@echo "bin package name  = $(bin_pkg_name)"
+	@echo "hdr package name  = $(hdrs_pkg_name)"
+	@echo "doc package name  = $(doc_pkg_name)"
+	@echo "do_doc_package            = $(do_doc_package)"
+	@echo "do_doc_package_content    = $(do_doc_package_content)"
+	@echo "do_source_package         = $(do_source_package)"
+	@echo "do_source_package_content = $(do_source_package_content)"
+	@echo "do_libc_dev_package       = $(do_libc_dev_package)"
+	@echo "do_flavour_image_package  = $(do_flavour_image_package)"
+	@echo "do_flavour_header_package = $(do_flavour_header_package)"
+	@echo "do_common_headers_indep   = $(do_common_headers_indep)"
+	@echo "do_full_source            = $(do_full_source)"
+	@echo "do_odm_drivers            = $(do_odm_drivers)"
+	@echo "do_tools                  = $(do_tools)"
+	@echo "do_any_tools              = $(do_any_tools)"
+	@echo "do_linux_tools            = $(do_linux_tools)"
+	@echo " do_tools_cpupower         = $(do_tools_cpupower)"
+	@echo " do_tools_perf             = $(do_tools_perf)"
+	@echo " do_tools_bpftool          = $(do_tools_bpftool)"
+	@echo " do_tools_x86              = $(do_tools_x86)"
+	@echo " do_tools_host             = $(do_tools_host)"
+	@echo "do_cloud_tools            = $(do_cloud_tools)"
+	@echo " do_tools_hyperv           = $(do_tools_hyperv)"
+	@echo "any_signed                = $(any_signed)"
+	@echo " uefi_signed               = $(uefi_signed)"
+	@echo " opal_signed               = $(opal_signed)"
+	@echo " sipl_signed               = $(sipl_signed)"
+	@echo "full_build                = $(full_build)"
+	@echo "libc_dev_version          = $(libc_dev_version)"
+	@echo "DEB_HOST_GNU_TYPE         = $(DEB_HOST_GNU_TYPE)"
+	@echo "DEB_BUILD_GNU_TYPE        = $(DEB_BUILD_GNU_TYPE)"
+	@echo "DEB_HOST_ARCH             = $(DEB_HOST_ARCH)"
+	@echo "DEB_BUILD_ARCH            = $(DEB_BUILD_ARCH)"
+	@echo "arch                      = $(arch)"
+	@echo "kmake                     = $(kmake)"
+
+printchanges:
+	@baseCommit=$$(git log --pretty=format:'%H %s' | \
+		gawk '/UBUNTU: '".*Ubuntu-.*`echo $(prev_fullver) | sed 's/+/\\\\+/'`"'(~.*)?$$/ { print $$1; exit }'); \
+	if [ -z "$$baseCommit" ]; then \
+		echo "WARNING: couldn't find a commit for the previous version. Using the lastest one." >&2; \
+		baseCommit=$$(git log --pretty=format:'%H %s' | \
+			gawk '/UBUNTU:\s*Ubuntu-.*$$/ { print $$1; exit }'); \
+	fi; \
+	git log "$$baseCommit"..HEAD | \
+	$(DROOT)/scripts/misc/git-ubuntu-log $(ubuntu_log_opts)
+
+insertchanges: autoreconstruct finalchecks
+	$(DROOT)/scripts/misc/insert-changes $(DROOT) $(DEBIAN)
+
+autoreconstruct:
+	# No need for reconstruct for -rc kernels since we don't upload an
+	# orig tarball, so just remove it.
+	if grep -q "^EXTRAVERSION = -rc[0-9]\+$$" Makefile; then \
+		echo "exit 0" >$(DEBIAN)/reconstruct; \
+	else \
+		$(DROOT)/scripts/misc/gen-auto-reconstruct $(upstream_tag) $(DEBIAN)/reconstruct $(DROOT)/source/options; \
+	fi
+
+finalchecks: debian/control
+	$(DROOT)/scripts/misc/final-checks "$(DEBIAN)" "$(prev_fullver)"
+
+diffupstream:
+	@git diff-tree -p refs/remotes/linux-2.6/master..HEAD $(shell ls | grep -vE '^(ubuntu|$(DEBIAN)|\.git.*)')
+
+startnewrelease:
+	dh_testdir
+	@[ -f "$(DEBIAN)/etc/update.conf" ] && . "$(DEBIAN)/etc/update.conf"; \
+	if [ -n "$$BACKPORT_SUFFIX" ]; then \
+		ver="$$(dpkg-parsechangelog -l"$$DEBIAN_MASTER/changelog" -SVersion)$${BACKPORT_SUFFIX/--/}.1"; \
+		prev_ver="$$(dpkg-parsechangelog -l"$(DEBIAN)/changelog" -SVersion)"; \
+		if [ "$${ver%.*}" = "$${prev_ver%.*}" ]; then \
+			ver="$${ver%.*}.$$(( $${prev_ver##*.} +1 ))"; \
+		fi; \
+	else \
+		rev=$(revision); \
+		suffix=$$(echo "$${rev}" | sed 's/^[0-9]*\.[0-9]*//'); \
+		abi=$${rev%%.*}; \
+		upload=$${rev#*.}; \
+		upload=$${upload%$${suffix}}; \
+		ver=$(release)-$$((abi + 1)).$$((upload + 1))$${suffix}; \
+	fi; \
+	now="$(shell date -R)"; \
+	echo "Creating new changelog set for $$ver..."; \
+	echo -e "$(src_pkg_name) ($$ver) UNRELEASED; urgency=medium\n" > $(DEBIAN)/changelog.new; \
+	echo "  CHANGELOG: Do not edit directly. Autogenerated at release." >> \
+		$(DEBIAN)/changelog.new; \
+	echo "  CHANGELOG: Use the printchanges target to see the curent changes." \
+		>> $(DEBIAN)/changelog.new; \
+	echo "  CHANGELOG: Use the insertchanges target to create the final log." \
+		>> $(DEBIAN)/changelog.new; \
+	echo -e "\n -- $$DEBFULLNAME <$$DEBEMAIL>  $$now\n" >> \
+		$(DEBIAN)/changelog.new ; \
+	cat $(DEBIAN)/changelog >> $(DEBIAN)/changelog.new; \
+	mv $(DEBIAN)/changelog.new $(DEBIAN)/changelog
+
+compileselftests:
+	# a loop is needed here to fail on errors
+	for test in $(ubuntu_selftests); do \
+		$(kmake) -C tools/testing/selftests TARGETS="$$test"; \
+	done;
+
+runselftests:
+	$(kmake) -C tools/testing/selftests TARGETS="$(ubuntu_selftests)" run_tests
--- linux-xilinx-zynqmp-5.15.0.orig/debian/rules.d/2-binary-arch.mk
+++ linux-xilinx-zynqmp-5.15.0/debian/rules.d/2-binary-arch.mk
@@ -0,0 +1,866 @@
+# We don't want make removing intermediary stamps
+.SECONDARY :
+
+# Prepare the out-of-tree build directory
+ifeq ($(do_full_source),true)
+build_cd = cd $(builddir)/build-$*; #
+build_O  =
+else
+build_cd =
+build_O  = O=$(builddir)/build-$*
+endif
+
+# Typically supplied from the arch makefile, e.g., debian.master/control.d/armhf.mk
+ifneq ($(gcc),)
+kmake += CC=$(CROSS_COMPILE)$(gcc)
+endif
+
+shlibdeps_opts = $(if $(CROSS_COMPILE),-- -l$(CROSS_COMPILE:%-=/usr/%)/lib)
+
+debian/scripts/fix-filenames: debian/scripts/fix-filenames.c
+	$(CC) -o $@ $^
+
+$(stampdir)/stamp-prepare-%: config-prepare-check-%
+	@echo Debug: $@
+	@touch $@
+$(stampdir)/stamp-prepare-tree-%: target_flavour = $*
+$(stampdir)/stamp-prepare-tree-%: debian/scripts/fix-filenames
+	@echo Debug: $@
+	install -d $(builddir)/build-$*
+	touch $(builddir)/build-$*/ubuntu-build
+	[ "$(do_full_source)" != 'true' ] && true || \
+		rsync -a --exclude debian --exclude debian.master --exclude $(DEBIAN) * $(builddir)/build-$*
+	if [ -e $(commonconfdir)/config.common.ubuntu ]; then \
+		cat $(commonconfdir)/config.common.ubuntu $(archconfdir)/config.common.$(arch) $(archconfdir)/config.flavour.$(target_flavour) > $(builddir)/build-$*/.config; \
+	else \
+		python3 debian/scripts/misc/annotations --export --arch $(arch) --flavour $(target_flavour) | sed -e 's/.*CONFIG_VERSION_SIGNATURE.*/CONFIG_VERSION_SIGNATURE="Ubuntu $(release)-$(revision)-$* $(raw_kernelversion)"/' > $(builddir)/build-$*/.config; \
+	fi
+	sed -i 's/.*CONFIG_VERSION_SIGNATURE.*/CONFIG_VERSION_SIGNATURE="Ubuntu $(release)-$(revision)-$* $(raw_kernelversion)"/' $(builddir)/build-$*/.config
+	[ "$(do_odm_drivers)" = 'true' ] && true || \
+		sed -ie 's/.*CONFIG_UBUNTU_ODM_DRIVERS.*/# CONFIG_UBUNTU_ODM_DRIVERS is not set/' \
+		    $(builddir)/build-$*/.config
+	find $(builddir)/build-$* -name "*.ko" | xargs rm -f
+	$(build_cd) $(kmake) $(build_O) -j1 syncconfig prepare scripts
+	touch $@
+
+# Used by developers as a shortcut to prepare a tree for compilation.
+prepare-%: $(stampdir)/stamp-prepare-%
+	@echo Debug: $@
+# Used by developers to allow efficient pre-building without fakeroot.
+build-%: $(stampdir)/stamp-install-%
+	@echo Debug: $@
+
+# Do the actual build, including image and modules
+$(stampdir)/stamp-build-%: target_flavour = $*
+$(stampdir)/stamp-build-%: bldimg = $(call custom_override,build_image,$*)
+$(stampdir)/stamp-build-%: $(stampdir)/stamp-prepare-%
+	@echo Debug: $@ build_image $(build_image) bldimg $(bldimg)
+	$(build_cd) $(kmake) $(build_O) $(conc_level) $(bldimg) modules $(if $(filter true,$(do_dtbs)),dtbs)
+
+ifneq ($(skipdbg),true)
+	# The target scripts_gdb is part of "all", so we need to call it manually
+	if grep -q CONFIG_GDB_SCRIPTS=y $(builddir)/build-$*/.config; then \
+		$(build_cd) $(kmake) $(build_O) $(conc_level) scripts_gdb ; \
+	fi
+endif
+
+	# Collect the list of kernel source files used for this build. Need to do this early
+	# before modules are stripped. Fail if the resulting file is empty.
+	find $(builddir)/build-$* -name vmlinux -o -name \*.ko -exec dwarfdump -i {} \; | \
+		grep -E 'DW_AT_(call|decl)_file' | sed -n 's|.*\s/|/|p' | sort -u > \
+		$(builddir)/build-$*/sources.list
+	test -s $(builddir)/build-$*/sources.list
+
+	@touch $@
+
+define build_dkms_sign =
+	$(shell set -x; if grep -q CONFIG_MODULE_SIG=y $(1)/.config; then
+			echo $(1)/scripts/sign-file $(MODHASHALGO) $(MODSECKEY) $(MODPUBKEY);
+		else
+			echo "-";
+		fi
+	)
+endef
+define build_dkms =
+	CROSS_COMPILE=$(CROSS_COMPILE) $(SHELL) $(DROOT)/scripts/dkms-build $(dkms_dir) $(abi_release)-$* '$(call build_dkms_sign,$(builddir)/build-$*)' $(1) $(2) $(3) $(4) $(5)
+endef
+
+define install_control =
+	for which in $(3);							\
+	do									\
+		template="$(DROOT)/templates/$(2).$$which.in";			\
+		script="$(DROOT)/$(1).$$which";					\
+		sed -e 's/@abiname@/$(abi_release)/g'				\
+		    -e 's/@localversion@/-$*/g'					\
+		    -e 's/@image-stem@/$(instfile)/g'				\
+			<"$$template" >"$$script";				\
+	done
+endef
+
+# Ensure the directory prefix is exactly 100 characters long so pathnames are the
+# exact same length in any binary files produced by the builds.  These will be
+# commonised later.
+dkms_20d=....................
+dkms_100d=$(dkms_20d)$(dkms_20d)$(dkms_20d)$(dkms_20d)$(dkms_20d)
+dkms_100c=$(shell echo '$(dkms_100d)' | sed -e 's/\./_/g')
+define dkms_dir_prefix =
+$(shell echo $(1)/$(dkms_100c) | \
+	sed -e 's/\($(dkms_100d)\).*/\1/' -e 's/^\(.*\)....$$/\1dkms/')
+endef
+
+# Install the finished build
+$(stampdir)/stamp-install-%: pkgdir_bin = $(CURDIR)/debian/$(bin_pkg_name)-$*
+$(stampdir)/stamp-install-%: pkgdir = $(CURDIR)/debian/$(mods_pkg_name)-$*
+$(stampdir)/stamp-install-%: pkgdir_ex = $(CURDIR)/debian/$(mods_extra_pkg_name)-$*
+$(stampdir)/stamp-install-%: pkgdir_bldinfo = $(CURDIR)/debian/$(bldinfo_pkg_name)-$*
+$(stampdir)/stamp-install-%: bindoc = $(pkgdir)/usr/share/doc/$(bin_pkg_name)-$*
+$(stampdir)/stamp-install-%: dbgpkgdir = $(CURDIR)/debian/$(bin_pkg_name)-$*-dbgsym
+$(stampdir)/stamp-install-%: signingv = $(CURDIR)/debian/$(bin_pkg_name)-signing/$(release)-$(revision)
+$(stampdir)/stamp-install-%: toolspkgdir = $(CURDIR)/debian/$(tools_flavour_pkg_name)-$*
+$(stampdir)/stamp-install-%: cloudpkgdir = $(CURDIR)/debian/$(cloud_flavour_pkg_name)-$*
+$(stampdir)/stamp-install-%: basepkg = $(hdrs_pkg_name)
+$(stampdir)/stamp-install-%: indeppkg = $(indep_hdrs_pkg_name)
+$(stampdir)/stamp-install-%: kernfile = $(call custom_override,kernel_file,$*)
+$(stampdir)/stamp-install-%: instfile = $(call custom_override,install_file,$*)
+$(stampdir)/stamp-install-%: hdrdir = $(CURDIR)/debian/$(basepkg)-$*/usr/src/$(basepkg)-$*
+$(stampdir)/stamp-install-%: target_flavour = $*
+$(stampdir)/stamp-install-%: MODHASHALGO=sha512
+$(stampdir)/stamp-install-%: MODSECKEY=$(builddir)/build-$*/certs/signing_key.pem
+$(stampdir)/stamp-install-%: MODPUBKEY=$(builddir)/build-$*/certs/signing_key.x509
+$(stampdir)/stamp-install-%: build_dir=$(builddir)/build-$*
+$(stampdir)/stamp-install-%: dkms_dir=$(call dkms_dir_prefix,$(builddir)/build-$*)
+$(foreach _m,$(all_dkms_modules), \
+  $(eval $$(stampdir)/stamp-install-%: enable_$(_m) = $$(filter true,$$(call custom_override,do_$(_m),$$*))) \
+  $(eval $$(stampdir)/stamp-install-%: dkms_$(_m)_pkgdir = $$(CURDIR)/debian/$(dkms_$(_m)_pkg_name)-$$*) \
+)
+$(stampdir)/stamp-install-%: dbgpkgdir_dkms = $(if $(filter true,$(skipdbg)),"",$(dbgpkgdir)/usr/lib/debug/lib/modules/$(abi_release)-$*/kernel)
+$(stampdir)/stamp-install-%: $(stampdir)/stamp-build-% $(stampdir)/stamp-install-headers
+	@echo Debug: $@ kernel_file $(kernel_file) kernfile $(kernfile) install_file $(install_file) instfile $(instfile)
+	dh_testdir
+	dh_prep -p$(bin_pkg_name)-$*
+	dh_prep -p$(mods_pkg_name)-$*
+	dh_prep -p$(hdrs_pkg_name)-$*
+	$(foreach _m,$(all_standalone_dkms_modules), \
+	  $(if $(enable_$(_m)),dh_prep -p$(dkms_$(_m)_pkg_name)-$*;)\
+	)
+ifneq ($(skipdbg),true)
+	dh_prep -p$(bin_pkg_name)-$*-dbgsym
+endif
+
+	# The main image
+	# compress_file logic required because not all architectures
+	# generate a zImage automatically out of the box
+ifeq ($(compress_file),)
+	install -m600 -D $(builddir)/build-$*/$(kernfile) \
+		$(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$*
+else
+	install -d $(pkgdir_bin)/boot
+	gzip -c9v $(builddir)/build-$*/$(kernfile) > \
+		$(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$*
+	chmod 600 $(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$*
+endif
+
+ifeq ($(uefi_signed),true)
+	install -d $(signingv)
+	# gzipped kernel images must be decompressed for signing
+	if [[ "$(kernfile)" =~ \.gz$$ ]]; then \
+		< $(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$* \
+			gunzip -cv > $(signingv)/$(instfile)-$(abi_release)-$*.efi; \
+		cp -p --attributes-only $(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$* \
+			$(signingv)/$(instfile)-$(abi_release)-$*.efi; \
+		echo "GZIP=1" >> $(signingv)/$(instfile)-$(abi_release)-$*.efi.vars; \
+	else \
+		cp -p $(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$* \
+			$(signingv)/$(instfile)-$(abi_release)-$*.efi; \
+	fi
+endif
+ifeq ($(opal_signed),true)
+	install -d $(signingv)
+	cp -p $(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$* \
+		$(signingv)/$(instfile)-$(abi_release)-$*.opal;
+endif
+ifeq ($(sipl_signed),true)
+	install -d $(signingv)
+	cp -p $(pkgdir_bin)/boot/$(instfile)-$(abi_release)-$* \
+		$(signingv)/$(instfile)-$(abi_release)-$*.sipl;
+endif
+
+	install -d $(pkgdir)/boot
+	install -m644 $(builddir)/build-$*/.config \
+		$(pkgdir)/boot/config-$(abi_release)-$*
+	install -m600 $(builddir)/build-$*/System.map \
+		$(pkgdir)/boot/System.map-$(abi_release)-$*
+
+ifeq ($(do_dtbs),true)
+	$(build_cd) $(kmake) $(build_O) $(conc_level) dtbs_install \
+		INSTALL_DTBS_PATH=$(pkgdir)/lib/firmware/$(abi_release)-$*/device-tree
+endif
+
+ifeq ($(no_dumpfile),)
+	makedumpfile -g $(pkgdir)/boot/vmcoreinfo-$(abi_release)-$* \
+		-x $(builddir)/build-$*/vmlinux
+	chmod 0600 $(pkgdir)/boot/vmcoreinfo-$(abi_release)-$*
+endif
+
+	$(build_cd) $(kmake) $(build_O) $(conc_level) modules_install $(vdso) \
+		INSTALL_MOD_STRIP=1 INSTALL_MOD_PATH=$(pkgdir)/ \
+		INSTALL_FW_PATH=$(pkgdir)/lib/firmware/$(abi_release)-$*
+
+	#
+	# Build module blacklists:
+	#  - blacklist all watchdog drivers (LP:1432837)
+	#
+	install -d $(pkgdir)/lib/modprobe.d
+	echo "# Kernel supplied blacklist for $(src_pkg_name) $(abi_release)-$* $(arch)" \
+		>$(pkgdir)/lib/modprobe.d/blacklist_$(src_pkg_name)_$(abi_release)-$*.conf
+	for conf in $(arch)-$* $(arch) common.conf; do \
+		if [ -f $(DEBIAN)/modprobe.d/$$conf ]; then \
+			echo "# modprobe.d/$$conf"; \
+			cat $(DEBIAN)/modprobe.d/$$conf; \
+		fi; \
+	done >>$(pkgdir)/lib/modprobe.d/blacklist_$(src_pkg_name)_$(abi_release)-$*.conf
+	echo "# Autogenerated watchdog blacklist" \
+		>>$(pkgdir)/lib/modprobe.d/blacklist_$(src_pkg_name)_$(abi_release)-$*.conf
+	ls -1 $(pkgdir)/lib/modules/$(abi_release)-$*/kernel/drivers/watchdog/ | \
+		grep -v '^bcm2835_wdt$$' | \
+		sed -e 's/^/blacklist /' -e 's/.ko$$//' | \
+		sort -u \
+		>>$(pkgdir)/lib/modprobe.d/blacklist_$(src_pkg_name)_$(abi_release)-$*.conf
+
+ifeq ($(do_extras_package),true)
+	#
+	# Remove all modules not in the inclusion list.
+	#
+	if [ -f $(DEBIAN)/control.d/$(target_flavour).inclusion-list ] ; then \
+		/sbin/depmod -v -b $(pkgdir) $(abi_release)-$* | \
+			sed -e "s@$(pkgdir)/lib/modules/$(abi_release)-$*/kernel/@@g" | \
+			awk '{ print $$1 " " $$NF}' >$(build_dir)/module-inclusion.depmap; \
+		mkdir -p $(pkgdir_ex)/lib/modules/$(abi_release)-$*; \
+		mv $(pkgdir)/lib/modules/$(abi_release)-$*/kernel \
+			$(pkgdir_ex)/lib/modules/$(abi_release)-$*/kernel; \
+		$(SHELL) $(DROOT)/scripts/module-inclusion --master \
+			$(pkgdir_ex)/lib/modules/$(abi_release)-$*/kernel \
+			$(pkgdir)/lib/modules/$(abi_release)-$*/kernel \
+			$(DEBIAN)/control.d/$(target_flavour).inclusion-list \
+			$(build_dir)/module-inclusion.depmap 2>&1 | \
+				tee $(target_flavour).inclusion-list.log; \
+		/sbin/depmod -b $(pkgdir) -ea -F $(pkgdir)/boot/System.map-$(abi_release)-$* \
+			$(abi_release)-$* 2>&1 |tee $(target_flavour).depmod.log; \
+		if [ `grep -c 'unknown symbol' $(target_flavour).depmod.log` -gt 0 ]; then \
+			echo "EE: Unresolved module dependencies in base package!"; \
+			exit 1; \
+		fi \
+	fi
+endif
+
+ifeq ($(no_dumpfile),)
+	makedumpfile -g $(pkgdir)/boot/vmcoreinfo-$(abi_release)-$* \
+		-x $(builddir)/build-$*/vmlinux
+	chmod 0600 $(pkgdir)/boot/vmcoreinfo-$(abi_release)-$*
+endif
+	rm -f $(pkgdir)/lib/modules/$(abi_release)-$*/build
+	rm -f $(pkgdir)/lib/modules/$(abi_release)-$*/source
+
+	# Some initramfs-tools specific modules
+	install -d $(pkgdir)/lib/modules/$(abi_release)-$*/initrd
+	if [ -f $(pkgdir)/lib/modules/$(abi_release)-$*/kernel/drivers/video/vesafb.ko ]; then\
+	  $(LN) $(pkgdir)/lib/modules/$(abi_release)-$*/kernel/drivers/video/vesafb.ko \
+		$(pkgdir)/lib/modules/$(abi_release)-$*/initrd/; \
+	fi
+
+	echo "interest linux-update-$(abi_release)-$*" >"$(DROOT)/$(bin_pkg_name)-$*.triggers"
+	install -d $(pkgdir_bin)/usr/lib/linux/triggers
+	$(call install_control,$(bin_pkg_name)-$*,image,postinst postrm preinst prerm)
+	install -d $(pkgdir)/usr/lib/linux/triggers
+	$(call install_control,$(mods_pkg_name)-$*,extra,postinst postrm)
+ifeq ($(do_extras_package),true)
+	# Install the postinit/postrm scripts in the extras package.
+	if [ -f $(DEBIAN)/control.d/$(target_flavour).inclusion-list ] ; then	\
+		install -d $(pkgdir_ex)/usr/lib/linux/triggers; \
+		$(call install_control,$(mods_extra_pkg_name)-$*,extra,postinst postrm); \
+	fi
+endif
+	$(foreach _m,$(all_standalone_dkms_modules), \
+	  $(if $(enable_$(_m)), \
+	    install -d $(dkms_$(_m)_pkgdir)/usr/lib/linux/triggers; \
+	    $(call install_control,$(dkms_$(_m)_pkg_name)-$*,extra,postinst postrm); \
+	  ) \
+	)
+
+	# Install the full changelog.
+ifeq ($(do_doc_package),true)
+	install -d $(bindoc)
+	cat $(DEBIAN)/changelog $(DEBIAN)/changelog.historical | \
+		gzip -9 >$(bindoc)/changelog.Debian.old.gz
+	chmod 644 $(bindoc)/changelog.Debian.old.gz
+endif
+
+ifneq ($(skipsub),true)
+	for sub in $($(*)_sub); do					\
+		if ! (TO=$$sub FROM=$* ABI_RELEASE=$(abi_release) $(SHELL)		\
+			$(DROOT)/scripts/sub-flavour); then exit 1; fi;		\
+		/sbin/depmod -b debian/$(bin_pkg_name)-$$sub		\
+			-ea -F debian/$(bin_pkg_name)-$$sub/boot/System.map-$(abi_release)-$* \
+			$(abi_release)-$*;					\
+		$(call install_control,$(bin_pkg_name)--$$sub,image,postinst postrm preinst prerm); \
+	done
+endif
+
+ifneq ($(skipdbg),true)
+	# Debug image is simple
+	install -m644 -D $(builddir)/build-$*/vmlinux \
+		$(dbgpkgdir)/usr/lib/debug/boot/vmlinux-$(abi_release)-$*
+	if [ -d $(builddir)/build-$*/scripts/gdb/linux ]; then \
+		install -m644 -D $(builddir)/build-$*/vmlinux-gdb.py \
+			$(dbgpkgdir)/usr/share/gdb/auto-load/boot/vmlinux-$(abi_release)-$*/vmlinuz-$(abi_release)-$*-gdb.py; \
+		install -m644 -D $(builddir)/build-$*/scripts/gdb/linux/* \
+			--target-directory=$(dbgpkgdir)/usr/share/gdb/auto-load/boot/vmlinux-$(abi_release)-$*/scripts/gdb/linux; \
+	fi
+	$(build_cd) $(kmake) $(build_O) modules_install $(vdso) \
+		INSTALL_MOD_PATH=$(dbgpkgdir)/usr/lib/debug
+	# Add .gnu_debuglink sections only after all/DKMS modules are built.
+	rm -f $(dbgpkgdir)/usr/lib/debug/lib/modules/$(abi_release)-$*/build
+	rm -f $(dbgpkgdir)/usr/lib/debug/lib/modules/$(abi_release)-$*/source
+	rm -f $(dbgpkgdir)/usr/lib/debug/lib/modules/$(abi_release)-$*/modules.*
+	rm -fr $(dbgpkgdir)/usr/lib/debug/lib/firmware
+endif
+
+	# The flavour specific headers image
+	# TODO: Would be nice if we didn't have to dupe the original builddir
+	install -d -m755 $(hdrdir)
+	cp $(builddir)/build-$*/.config $(hdrdir)
+	chmod 644 $(hdrdir)/.config
+	$(kmake) O=$(hdrdir) -j1 syncconfig prepare scripts
+	# We'll symlink this stuff
+	rm -f $(hdrdir)/Makefile
+	rm -rf $(hdrdir)/include2 $(hdrdir)/source
+	# We do not need the retpoline information.
+	find $(hdrdir) -name \*.o.ur-\* | xargs rm -f
+	# Copy over the compilation version.
+	cp "$(builddir)/build-$*/include/generated/compile.h" \
+		"$(hdrdir)/include/generated/compile.h"
+	# Add UTS_UBUNTU_RELEASE_ABI since UTS_RELEASE is difficult to parse.
+	echo "#define UTS_UBUNTU_RELEASE_ABI $(abinum)" >> $(hdrdir)/include/generated/utsrelease.h
+	# powerpc kernel arch seems to need some .o files for external module linking. Add them in.
+ifeq ($(build_arch),powerpc)
+	mkdir -p $(hdrdir)/arch/powerpc/lib
+	cp $(builddir)/build-$*/arch/powerpc/lib/*.o $(hdrdir)/arch/powerpc/lib
+endif
+ifeq ($(build_arch),s390)
+	if [ -n "$$(find $(builddir)/build-$*/arch/s390/lib/expoline -maxdepth 1 -name '*.o' -print -quit)" ]; then \
+		mkdir -p $(hdrdir)/arch/s390/lib/expoline/; \
+		cp $(builddir)/build-$*/arch/s390/lib/expoline/*.o $(hdrdir)/arch/s390/lib/expoline/; \
+	fi
+endif
+	# Copy over scripts/module.lds for building external modules
+	cp $(builddir)/build-$*/scripts/module.lds $(hdrdir)/scripts
+	# Copy over the new retpoline extractor.
+	cp scripts/ubuntu-retpoline-extract-one $(hdrdir)/scripts
+	# Script to symlink everything up
+	$(SHELL) $(DROOT)/scripts/link-headers "$(hdrdir)" "$(indeppkg)" "$*"
+	# The build symlink
+	install -d debian/$(basepkg)-$*/lib/modules/$(abi_release)-$*
+	$(LN) /usr/src/$(basepkg)-$* \
+		debian/$(basepkg)-$*/lib/modules/$(abi_release)-$*/build
+	# And finally the symvers
+	install -m644 $(builddir)/build-$*/Module.symvers \
+		$(hdrdir)/Module.symvers
+
+	# Now the header scripts
+	$(call install_control,$(hdrs_pkg_name)-$*,headers,postinst)
+
+	# At the end of the package prep, call the tests
+	DPKG_ARCH="$(arch)" KERN_ARCH="$(build_arch)" FLAVOUR="$*"	\
+	 VERSION="$(abi_release)" REVISION="$(revision)"		\
+	 PREV_REVISION="$(prev_revision)" ABI_NUM="$(abinum)"		\
+	 PREV_ABI_NUM="$(prev_abinum)" BUILD_DIR="$(builddir)/build-$*"	\
+	 INSTALL_DIR="$(pkgdir)" SOURCE_DIR="$(CURDIR)"			\
+	 run-parts -v $(DROOT)/tests-build
+
+	#
+	# Remove files which are generated at installation by postinst,
+	# except for modules.order and modules.builtin
+	# 
+	# NOTE: need to keep this list in sync with postrm
+	#
+	mkdir $(pkgdir)/lib/modules/$(abi_release)-$*/_
+	mv $(pkgdir)/lib/modules/$(abi_release)-$*/modules.order \
+		$(pkgdir)/lib/modules/$(abi_release)-$*/_
+	if [ -f $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin ] ; then \
+	    mv $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin \
+		$(pkgdir)/lib/modules/$(abi_release)-$*/_; \
+	fi
+	if [ -f $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin.modinfo ] ; then \
+	    mv $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin.modinfo \
+		$(pkgdir)/lib/modules/$(abi_release)-$*/_; \
+	fi
+	rm -f $(pkgdir)/lib/modules/$(abi_release)-$*/modules.*
+	mv $(pkgdir)/lib/modules/$(abi_release)-$*/_/* \
+		$(pkgdir)/lib/modules/$(abi_release)-$*
+	rmdir $(pkgdir)/lib/modules/$(abi_release)-$*/_
+
+ifeq ($(do_linux_tools),true)
+	# Create the linux-tools tool links
+	install -d $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+ifeq ($(do_tools_usbip),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/usbip $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/usbipd $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+ifeq ($(do_tools_acpidbg),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/acpidbg $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+ifeq ($(do_tools_cpupower),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/cpupower $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+ifeq ($(do_tools_perf),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/perf $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+ifeq ($(do_tools_perf_jvmti),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/libperf-jvmti.so $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+endif
+ifeq ($(do_tools_bpftool),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/bpftool $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+ifeq ($(do_tools_x86),true)
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/x86_energy_perf_policy $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/turbostat $(toolspkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+endif
+ifeq ($(do_cloud_tools),true)
+ifeq ($(do_tools_hyperv),true)
+	# Create the linux-hyperv tool links
+	install -d $(cloudpkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/hv_kvp_daemon $(cloudpkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/hv_vss_daemon $(cloudpkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/hv_fcopy_daemon $(cloudpkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+	$(LN) ../../$(src_pkg_name)-tools-$(abi_release)/lsvmbus $(cloudpkgdir)/usr/lib/linux-tools/$(abi_release)-$*
+endif
+endif
+
+	# Build a temporary "installed headers" directory.
+	install -d $(dkms_dir) $(dkms_dir)/headers $(dkms_dir)/build $(dkms_dir)/source
+	cp -rp "$(hdrdir)" "$(indep_hdrdir)" "$(dkms_dir)/headers"
+
+	$(foreach _m,$(all_dkms_modules), \
+	  $(if $(enable_$(_m)), \
+	    $(call build_dkms,$(dkms_$(_m)_pkg_name)-$*,$(dkms_$(_m)_pkgdir)/lib/modules/$(abi_release)-$*/$(dkms_$(_m)_subdir),$(dbgpkgdir_dkms),$(_m),$(dkms_$(_m)_debpath)); \
+	  ) \
+	)
+
+
+ifneq ($(skipdbg),true)
+	# Add .gnu_debuglink sections to each stripped .ko
+	# pointing to unstripped verson
+	find $(pkgdir) \
+	  $(if $(filter true,$(do_extras_package)),$(pkgdir_ex)) \
+	  -name '*.ko' | while read path_module ; do \
+		module="/lib/modules/$${path_module#*/lib/modules/}"; \
+		if [[ -f "$(dbgpkgdir)/usr/lib/debug/$$module" ]] ; then \
+			while IFS= read -r -d '' signature < <(tail -c 28 "$$path_module"); do \
+				break; \
+			done; \
+			$(CROSS_COMPILE)objcopy \
+				--add-gnu-debuglink=$(dbgpkgdir)/usr/lib/debug/$$module \
+				$$path_module; \
+			if grep -q CONFIG_MODULE_SIG=y $(builddir)/build-$*/.config && \
+			   [ "$$signature" = $$'~Module signature appended~\n' ]; then \
+				$(builddir)/build-$*/scripts/sign-file $(MODHASHALGO) \
+					$(MODSECKEY) \
+					$(MODPUBKEY) \
+					$$path_module; \
+			fi; \
+		else \
+			echo "WARNING: Missing debug symbols for module '$$module'."; \
+		fi; \
+	done
+endif
+
+	# Build the final ABI information.
+	install -d $(abidir)
+	sed -e 's/^\(.\+\)[[:space:]]\+\(.\+\)[[:space:]]\(.\+\)$$/\3 \2 \1/'	\
+		$(builddir)/build-$*/Module.symvers | sort > $(abidir)/$*
+
+	# Build the final ABI modules information.
+	find $(pkgdir_bin) $(pkgdir) $(pkgdir_ex) -name \*.ko | \
+		sed -e 's/.*\/\([^\/]*\)\.ko/\1/' | sort > $(abidir)/$*.modules
+
+	# Build the final ABI built-in modules information.
+	if [ -f $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin ] ; then \
+		sed -e 's/.*\/\([^\/]*\)\.ko/\1/' $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin | \
+			sort > $(abidir)/$*.modules.builtin; \
+	fi
+
+	# Build the final ABI firmware information.
+	find $(pkgdir_bin) $(pkgdir) $(pkgdir_ex) -name \*.ko | \
+	while read ko; do \
+		/sbin/modinfo $$ko | grep ^firmware || true; \
+	done | sort -u >$(abidir)/$*.fwinfo
+
+	# Build the final ABI built-in firmware information.
+	if [ -f $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin.modinfo ] ; then \
+		cat $(pkgdir)/lib/modules/$(abi_release)-$*/modules.builtin.modinfo | \
+			tr '\0' '\n' | sed -n 's/^.*firmware=/firmware: /p' | \
+			sort -u > $(abidir)/$*.fwinfo.builtin; \
+	fi
+
+	# Build the final ABI compiler information.
+	ko=$$(find $(pkgdir_bin) $(pkgdir) $(pkgdir_ex) -name \*.ko | head -1); \
+	readelf -p .comment "$$ko" | gawk ' \
+		($$1 == "[") { \
+			printf("%s", $$3); \
+			for (n=4; n<=NF; n++) { \
+				printf(" %s", $$n); \
+			} \
+			print "" \
+		}' | sort -u >$(abidir)/$*.compiler
+
+	# Build the final ABI retpoline information.
+	if grep -q CONFIG_RETPOLINE=y $(builddir)/build-$*/.config; then \
+		echo "# retpoline v1.0" >$(abidir)/$*.retpoline; \
+		$(SHELL) $(DROOT)/scripts/retpoline-extract $(builddir)/build-$* $(CURDIR) | \
+			sort >>$(abidir)/$*.retpoline; \
+	else \
+		echo "# RETPOLINE NOT ENABLED" >$(abidir)/$*.retpoline; \
+	fi
+
+	# Build the buildinfo package content.
+	install -d $(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*
+	install -m644 $(builddir)/build-$*/.config \
+		$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/config
+	install -m644 $(abidir)/$* \
+		$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/abi
+	install -m644 $(abidir)/$*.modules \
+		$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/modules
+	install -m644 $(abidir)/$*.fwinfo \
+		$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/fwinfo
+	install -m644 $(abidir)/$*.retpoline \
+		$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/retpoline
+	install -m644 $(abidir)/$*.compiler \
+		$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/compiler
+	if [ -f $(abidir)/$*.modules.builtin ] ; then \
+		install -m644 $(abidir)/$*.modules.builtin \
+			$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/modules.builtin; \
+	fi
+	if [ -f $(abidir)/$*.fwinfo.builtin ] ; then \
+		install -m644 $(abidir)/$*.fwinfo.builtin \
+			$(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/fwinfo.builtin; \
+	fi
+	install -m644 $(DROOT)/canonical-certs.pem $(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/canonical-certs.pem
+	install -m644 $(DROOT)/canonical-revoked-certs.pem $(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/canonical-revoked-certs.pem
+	# List of source files used for this build
+	install -m644 $(builddir)/build-$*/sources.list $(pkgdir_bldinfo)/usr/lib/linux/$(abi_release)-$*/sources
+
+ifneq ($(full_build),false)
+	# Clean out this flavours build directory.
+	rm -rf $(builddir)/build-$*
+endif
+	@touch $@
+
+headers_tmp := $(CURDIR)/debian/tmp-headers
+headers_dir := $(CURDIR)/debian/linux-libc-dev
+
+hmake := $(MAKE) -C $(CURDIR) O=$(headers_tmp) \
+	KERNELVERSION=$(abi_release) INSTALL_HDR_PATH=$(headers_tmp)/install \
+	SHELL="$(SHELL)" ARCH=$(header_arch)
+
+install-arch-headers:
+	@echo Debug: $@
+	dh_testdir
+	dh_testroot
+ifeq ($(do_libc_dev_package),true)
+	dh_prep -plinux-libc-dev
+endif
+
+	rm -rf $(headers_tmp)
+	install -d $(headers_tmp) $(headers_dir)/usr/include/
+
+	$(hmake) $(defconfig)
+	mv $(headers_tmp)/.config $(headers_tmp)/.config.old
+	sed -e 's/^# \(CONFIG_MODVERSIONS\) is not set$$/\1=y/' \
+	  -e 's/.*CONFIG_LOCALVERSION_AUTO.*/# CONFIG_LOCALVERSION_AUTO is not set/' \
+	  $(headers_tmp)/.config.old > $(headers_tmp)/.config
+	$(hmake) syncconfig
+	$(hmake) headers_install
+
+	( cd $(headers_tmp)/install/include/ && \
+		find . -name '.' -o -name '.*' -prune -o -print | \
+                cpio -pvd --preserve-modification-time \
+			$(headers_dir)/usr/include/ )
+	mkdir $(headers_dir)/usr/include/$(DEB_HOST_MULTIARCH)
+	mv $(headers_dir)/usr/include/asm $(headers_dir)/usr/include/$(DEB_HOST_MULTIARCH)/
+
+	rm -rf $(headers_tmp)
+
+define dh_all
+	dh_installchangelogs -p$(1)
+	dh_installdocs -p$(1)
+	dh_compress -p$(1)
+	dh_fixperms -p$(1) -X/boot/
+	dh_shlibdeps -p$(1) $(shlibdeps_opts)
+	dh_installdeb -p$(1)
+	dh_installdebconf -p$(1)
+	$(lockme) dh_gencontrol -p$(1) -- -Vlinux:rprovides='$(rprovides)' $(2)
+	dh_md5sums -p$(1)
+	dh_builddeb -p$(1)
+endef
+define newline
+
+
+endef
+define dh_all_inline
+        $(subst ${newline},; \${newline},$(call dh_all,$(1),$(2)))
+endef
+
+binary-arch-headers: install-arch-headers
+	@echo Debug: $@
+	dh_testdir
+	dh_testroot
+ifeq ($(do_libc_dev_package),true)
+ifeq ($(filter debian.master%,$(DEBIAN)),)
+	echo "non-master branch building linux-libc-dev, aborting"
+	exit 1
+endif
+	$(call dh_all,linux-libc-dev)
+endif
+
+binary-%: pkgimg = $(bin_pkg_name)-$*
+binary-%: pkgimg_mods = $(mods_pkg_name)-$*
+binary-%: pkgimg_ex = $(mods_extra_pkg_name)-$*
+binary-%: pkgdir_ex = $(CURDIR)/debian/$(extra_pkg_name)-$*
+binary-%: pkgbldinfo = $(bldinfo_pkg_name)-$*
+binary-%: pkghdr = $(hdrs_pkg_name)-$*
+binary-%: dbgpkg = $(bin_pkg_name)-$*-dbgsym
+binary-%: dbgpkgdir = $(CURDIR)/debian/$(bin_pkg_name)-$*-dbgsym
+binary-%: pkgtools = $(tools_flavour_pkg_name)-$*
+binary-%: pkgcloud = $(cloud_flavour_pkg_name)-$*
+$(foreach _m,$(all_dkms_modules), \
+  $(eval binary-%: enable_$(_m) = $$(filter true,$$(call custom_override,do_$(_m),$$*))) \
+)
+binary-%: rprovides = $(foreach _m,$(all_built-in_dkms_modules),$(if $(enable_$(_m)),$(foreach _r,$(dkms_$(_m)_rprovides),$(_r)$(comma) )))
+binary-%: target_flavour = $*
+binary-%: checks-%
+	@echo Debug: $@
+	dh_testdir
+	dh_testroot
+
+	$(call dh_all,$(pkgimg)) -- -Znone
+	$(call dh_all,$(pkgimg_mods))
+
+ifeq ($(do_extras_package),true)
+  ifeq ($(ship_extras_package),false)
+	# If $(ship_extras_package) is explicitly set to false, then do not
+	# construct the linux-image-extra package; instead just log all of the
+	# "extra" modules which were pointlessly built yet won't be shipped.
+	find $(pkgdir_ex) -name '*.ko' | sort \
+		| sed 's|^$(pkgdir_ex)/|NOT-SHIPPED |' \
+		| tee -a $(target_flavour).not-shipped.log;
+  else
+	if [ -f $(DEBIAN)/control.d/$(target_flavour).inclusion-list ] ; then \
+		$(call dh_all_inline,$(pkgimg_ex)); \
+	fi
+  endif
+endif
+
+	$(foreach _m,$(all_standalone_dkms_modules), \
+	  $(if $(enable_$(_m)),$(call dh_all,$(dkms_$(_m)_pkg_name)-$*);)\
+	)
+
+	$(call dh_all,$(pkgbldinfo))
+	$(call dh_all,$(pkghdr))
+
+ifneq ($(skipsub),true)
+	@set -e; for sub in $($(*)_sub); do		\
+		pkg=$(bin_pkg_name)-$$sub;		\
+		$(call dh_all_inline,$$pkg);		\
+	done
+endif
+
+ifneq ($(skipdbg),true)
+	$(call dh_all,$(dbgpkg)) -- -Zxz
+
+	# Hokay...here's where we do a little twiddling...
+	# Renaming the debug package prevents it from getting into
+	# the primary archive, and therefore prevents this very large
+	# package from being mirrored. It is instead, through some
+	# archive admin hackery, copied to http://ddebs.ubuntu.com.
+	#
+	mv ../$(dbgpkg)_$(release)-$(revision)_$(arch).deb \
+		../$(dbgpkg)_$(release)-$(revision)_$(arch).ddeb
+	set -e; \
+	( \
+		$(lockme_cmd) 9 || exit 1; \
+		if grep -qs '^Build-Debug-Symbols: yes$$' /CurrentlyBuilding; then \
+			sed -i '/^$(dbgpkg)_/s/\.deb /.ddeb /' debian/files; \
+		else \
+			grep -v '^$(dbgpkg)_.*$$' debian/files > debian/files.new; \
+			mv debian/files.new debian/files; \
+		fi; \
+	) 9>$(lockme_file)
+	# Now, the package wont get into the archive, but it will get put
+	# into the debug system.
+endif
+
+ifeq ($(do_linux_tools),true)
+	$(call dh_all,$(pkgtools))
+endif
+ifeq ($(do_cloud_tools),true)
+	$(call dh_all,$(pkgcloud))
+endif
+
+ifneq ($(full_build),false)
+	# Clean out the debugging package source directory.
+	rm -rf $(dbgpkgdir)
+endif
+
+#
+# per-architecture packages
+#
+builddirpa = $(builddir)/tools-perarch
+
+$(stampdir)/stamp-prepare-perarch:
+	@echo Debug: $@
+ifeq ($(do_any_tools),true)
+	rm -rf $(builddirpa)
+	install -d $(builddirpa)
+	rsync -a --exclude debian --exclude debian.master --exclude $(DEBIAN) --exclude .git -a ./ $(builddirpa)/
+endif
+	touch $@
+
+$(stampdir)/stamp-build-perarch: $(stampdir)/stamp-prepare-perarch install-arch-headers
+	@echo Debug: $@
+ifeq ($(do_linux_tools),true)
+ifeq ($(do_tools_usbip),true)
+	chmod 755 $(builddirpa)/tools/usb/usbip/autogen.sh
+	cd $(builddirpa)/tools/usb/usbip && ./autogen.sh
+	chmod 755 $(builddirpa)/tools/usb/usbip/configure
+	cd $(builddirpa)/tools/usb/usbip && ./configure --prefix=$(builddirpa)/tools/usb/usbip/bin
+	cd $(builddirpa)/tools/usb/usbip && make install CFLAGS="-g -O2 -static" CROSS_COMPILE=$(CROSS_COMPILE)
+endif
+ifeq ($(do_tools_acpidbg),true)
+	cd $(builddirpa)/tools/power/acpi && make clean && make CFLAGS="-g -O2 -static -I$(builddirpa)/include" CROSS_COMPILE=$(CROSS_COMPILE) acpidbg
+endif
+ifeq ($(do_tools_cpupower),true)
+	make -C $(builddirpa)/tools/power/cpupower \
+		CROSS_COMPILE=$(CROSS_COMPILE) \
+		CROSS=$(CROSS_COMPILE) \
+		STATIC=true \
+		CPUFREQ_BENCH=false
+endif
+ifeq ($(do_tools_perf),true)
+	cd $(builddirpa) && $(kmake) $(defconfig)
+	mv $(builddirpa)/.config $(builddirpa)/.config.old
+	sed -e 's/^# \(CONFIG_MODVERSIONS\) is not set$$/\1=y/' \
+	  -e 's/.*CONFIG_LOCALVERSION_AUTO.*/# CONFIG_LOCALVERSION_AUTO is not set/' \
+	  $(builddirpa)/.config.old > $(builddirpa)/.config
+	cd $(builddirpa) && $(kmake) syncconfig
+	cd $(builddirpa) && $(kmake) prepare
+	cd $(builddirpa)/tools/perf && \
+		$(kmake) prefix=/usr HAVE_NO_LIBBFD=1 HAVE_CPLUS_DEMANGLE_SUPPORT=1 CROSS_COMPILE=$(CROSS_COMPILE) NO_LIBPYTHON=1 NO_LIBPERL=1 WERROR=0
+endif
+ifeq ($(do_tools_bpftool),true)
+	$(kmake) CROSS_COMPILE=$(CROSS_COMPILE) -C $(builddirpa)/tools/bpf/bpftool
+endif
+ifeq ($(do_tools_x86),true)
+	cd $(builddirpa)/tools/power/x86/x86_energy_perf_policy && make CROSS_COMPILE=$(CROSS_COMPILE)
+	cd $(builddirpa)/tools/power/x86/turbostat && make CROSS_COMPILE=$(CROSS_COMPILE)
+endif
+endif
+ifeq ($(do_cloud_tools),true)
+ifeq ($(do_tools_hyperv),true)
+	cd $(builddirpa)/tools/hv && make CFLAGS="-I$(headers_dir)/usr/include -I$(headers_dir)/usr/include/$(DEB_HOST_MULTIARCH)" CROSS_COMPILE=$(CROSS_COMPILE) hv_kvp_daemon hv_vss_daemon hv_fcopy_daemon
+endif
+endif
+	@touch $@
+
+install-perarch: toolspkgdir = $(CURDIR)/debian/$(tools_pkg_name)
+install-perarch: cloudpkgdir = $(CURDIR)/debian/$(cloud_pkg_name)
+install-perarch: $(stampdir)/stamp-build-perarch
+	@echo Debug: $@
+	# Add the tools.
+ifeq ($(do_linux_tools),true)
+	install -d $(toolspkgdir)/usr/lib
+	install -d $(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+ifeq ($(do_tools_usbip),true)
+	install -m755 $(builddirpa)/tools/usb/usbip/bin/sbin/usbip \
+		$(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+	install -m755 $(builddirpa)/tools/usb/usbip/bin/sbin/usbipd \
+		$(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+ifeq ($(do_tools_acpidbg),true)
+	install -m755 $(builddirpa)/tools/power/acpi/acpidbg \
+		$(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+ifeq ($(do_tools_cpupower),true)
+	install -m755 $(builddirpa)/tools/power/cpupower/cpupower \
+		$(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+ifeq ($(do_tools_perf),true)
+	install -m755 $(builddirpa)/tools/perf/perf $(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+ifeq ($(do_tools_perf_jvmti),true)
+	install -m755 $(builddirpa)/tools/perf/libperf-jvmti.so $(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+endif
+ifeq ($(do_tools_bpftool),true)
+	install -m755 $(builddirpa)/tools/bpf/bpftool/bpftool $(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+ifeq ($(do_tools_x86),true)
+	install -m755 $(builddirpa)/tools/power/x86/x86_energy_perf_policy/x86_energy_perf_policy \
+		$(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+	install -m755 $(builddirpa)/tools/power/x86/turbostat/turbostat \
+		$(toolspkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+endif
+ifeq ($(do_cloud_tools),true)
+ifeq ($(do_tools_hyperv),true)
+	install -d $(cloudpkgdir)/usr/lib
+	install -d $(cloudpkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+	install -m755 $(builddirpa)/tools/hv/hv_kvp_daemon \
+		$(cloudpkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+	install -m755 $(builddirpa)/tools/hv/hv_vss_daemon \
+		$(cloudpkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+	install -m755 $(builddirpa)/tools/hv/hv_fcopy_daemon \
+		$(cloudpkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+	install -m755 $(builddirpa)/tools/hv/lsvmbus \
+		$(cloudpkgdir)/usr/lib/$(src_pkg_name)-tools-$(abi_release)
+endif
+endif
+
+binary-perarch: toolspkg = $(tools_pkg_name)
+binary-perarch: cloudpkg = $(cloud_pkg_name)
+binary-perarch: install-perarch
+	@echo Debug: $@
+ifeq ($(do_linux_tools),true)
+	$(call dh_all,$(toolspkg))
+endif
+ifeq ($(do_cloud_tools),true)
+	$(call dh_all,$(cloudpkg))
+endif
+
+binary-debs: signing = $(CURDIR)/debian/$(bin_pkg_name)-signing
+binary-debs: signingv = $(CURDIR)/debian/$(bin_pkg_name)-signing/$(release)-$(revision)
+binary-debs: signing_tar = $(src_pkg_name)_$(release)-$(revision)_$(arch).tar.gz
+binary-debs: binary-perarch $(addprefix binary-,$(flavours))
+	@echo Debug: $@
+ifeq ($(any_signed),true)
+	install -d $(signingv)/control
+	{ echo "tarball"; } >$(signingv)/control/options
+	cd $(signing) && tar czvf ../../../$(signing_tar) .
+	dpkg-distaddfile $(signing_tar) raw-signing -
+endif
+
+build-arch-deps-$(do_flavour_image_package) += $(addprefix $(stampdir)/stamp-install-,$(flavours))
+build-arch: $(build-arch-deps-true)
+	@echo Debug: $@
+
+ifeq ($(AUTOBUILD),)
+binary-arch-deps-$(do_flavour_image_package) += binary-debs
+else
+binary-arch-deps-$(do_flavour_image_package) = binary-debs
+endif
+binary-arch-deps-$(do_libc_dev_package) += binary-arch-headers
+ifneq ($(do_common_headers_indep),true)
+binary-arch-deps-$(do_flavour_header_package) += binary-headers
+endif
+binary-arch: $(binary-arch-deps-true)
+	@echo Debug: $@
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/rules.d/3-binary-indep.mk
+++ linux-xilinx-zynqmp-5.15.0/debian/rules.d/3-binary-indep.mk
@@ -0,0 +1,232 @@
+build-indep:
+	@echo Debug: $@
+
+# The binary-indep dependency chain is:
+#
+# install-headers <- install-doc <- install-source <- install-tools <- install-indep <- binary-indep
+# install-headers <- binary-headers
+#
+indep_hdrpkg = $(indep_hdrs_pkg_name)
+indep_hdrdir = $(CURDIR)/debian/$(indep_hdrpkg)/usr/src/$(indep_hdrpkg)
+$(stampdir)/stamp-install-headers: $(stampdir)/stamp-prepare-indep
+	@echo Debug: $@
+	dh_testdir
+
+ifeq ($(do_flavour_header_package),true)
+	install -d $(indep_hdrdir)
+	find . -path './debian' -prune -o -path './$(DEBIAN)' -prune \
+	  -o -path './include/*' -prune \
+	  -o -path './scripts/*' -prune -o -type f \
+	  \( -name 'Makefile*' -o -name 'Kconfig*' -o -name 'Kbuild*' -o \
+	     -name '*.sh' -o -name '*.pl' -o -name '*.lds' \) \
+	  -print | cpio -pd --preserve-modification-time $(indep_hdrdir)
+	cp -a scripts include $(indep_hdrdir)
+	(find arch -name include -type d -print | \
+		xargs -n1 -i: find : -type f) | \
+		cpio -pd --preserve-modification-time $(indep_hdrdir)
+endif
+	@touch $@
+
+docpkg = $(doc_pkg_name)
+docdir = $(CURDIR)/debian/$(docpkg)/usr/share/doc/$(docpkg)
+install-doc: $(stampdir)/stamp-prepare-indep
+	@echo Debug: $@
+ifeq ($(do_doc_package),true)
+	dh_testdir
+	dh_testroot
+
+	install -d $(docdir)
+ifeq ($(do_doc_package_content),true)
+	# First the html docs. We skip these for autobuilds
+	if [ -z "$(AUTOBUILD)" ]; then \
+		install -d $(docdir)/$(doc_pkg_name)-tmp; \
+		$(kmake) O=$(docdir)/$(doc_pkg_name)-tmp htmldocs; \
+		install -d $(docdir)/html; \
+		rsync -aL $(docdir)/$(doc_pkg_name)-tmp/Documentation/output/ \
+			$(docdir)/html/; \
+		rm -rf $(docdir)/$(doc_pkg_name)-tmp; \
+	fi
+endif
+	# Copy the rest
+	cp -a Documentation/* $(docdir)
+	find $(docdir) -name .gitignore | xargs rm -f
+endif
+
+srcpkg = linux-source-$(release)
+srcdir = $(CURDIR)/debian/$(srcpkg)/usr/src/$(srcpkg)
+balldir = $(CURDIR)/debian/$(srcpkg)/usr/src/$(srcpkg)/$(srcpkg)
+install-source: $(stampdir)/stamp-prepare-indep
+	@echo Debug: $@
+ifeq ($(do_source_package),true)
+
+	install -d $(srcdir)
+ifeq ($(do_source_package_content),true)
+	find . -path './debian' -prune -o -path './$(DEBIAN)' -prune -o \
+		-path './.*' -prune -o -print | \
+		cpio -pd --preserve-modification-time $(balldir)
+	(cd $(srcdir); tar cf - $(srcpkg)) | bzip2 -9c > \
+		$(srcdir)/$(srcpkg).tar.bz2
+	rm -rf $(balldir)
+	find './debian' './$(DEBIAN)' \
+		-path './debian/linux-*' -prune -o \
+		-path './debian/$(src_pkg_name)-*' -prune -o \
+		-path './debian/build' -prune -o \
+		-path './debian/files' -prune -o \
+		-path './debian/stamps' -prune -o \
+		-path './debian/tmp' -prune -o \
+		-path './$(DEBIAN)/__abi.current' -prune -o \
+		-print | \
+		cpio -pd --preserve-modification-time $(srcdir)
+	$(LN) $(srcpkg)/$(srcpkg).tar.bz2 $(srcdir)/..
+endif
+endif
+
+install-tools: toolspkg = $(tools_common_pkg_name)
+install-tools: toolsbin = $(CURDIR)/debian/$(toolspkg)/usr/bin
+install-tools: toolssbin = $(CURDIR)/debian/$(toolspkg)/usr/sbin
+install-tools: toolsman = $(CURDIR)/debian/$(toolspkg)/usr/share/man
+install-tools: toolsbashcomp = $(CURDIR)/debian/$(toolspkg)/usr/share/bash-completion/completions
+install-tools: hosttoolspkg = $(hosttools_pkg_name)
+install-tools: hosttoolsbin = $(CURDIR)/debian/$(hosttoolspkg)/usr/bin
+install-tools: hosttoolsman = $(CURDIR)/debian/$(hosttoolspkg)/usr/share/man
+install-tools: hosttoolssystemd = $(CURDIR)/debian/$(hosttoolspkg)/lib/systemd/system
+install-tools: cloudpkg = $(cloud_common_pkg_name)
+install-tools: cloudbin = $(CURDIR)/debian/$(cloudpkg)/usr/bin
+install-tools: cloudsbin = $(CURDIR)/debian/$(cloudpkg)/usr/sbin
+install-tools: cloudman = $(CURDIR)/debian/$(cloudpkg)/usr/share/man
+install-tools: $(stampdir)/stamp-prepare-indep $(stampdir)/stamp-build-perarch
+	@echo Debug: $@
+
+ifeq ($(do_tools_common),true)
+	rm -rf $(builddir)/tools
+	install -d $(builddir)/tools
+	for i in *; do $(LN) $(CURDIR)/$$i $(builddir)/tools/; done
+	rm $(builddir)/tools/tools
+	rsync -a tools/ $(builddir)/tools/tools/
+
+	install -d $(toolsbin)
+	install -d $(toolssbin)
+	install -d $(toolsman)/man1
+	install -d $(toolsman)/man8
+	install -d $(toolsbashcomp)
+
+	install -m755 debian/tools/generic $(toolsbin)/usbip
+	install -m755 debian/tools/generic $(toolsbin)/usbipd
+	install -m644 $(CURDIR)/tools/usb/usbip/doc/*.8 $(toolsman)/man8/
+
+	install -m755 debian/tools/generic $(toolsbin)/cpupower
+	install -m644 $(CURDIR)/tools/power/cpupower/man/*.1 $(toolsman)/man1/
+
+	install -m755 debian/tools/generic $(toolsbin)/perf
+
+	install -m755 debian/tools/generic $(toolssbin)/bpftool
+	make -C $(builddir)/tools/tools/bpf/bpftool doc
+	install -m644 $(builddir)/tools/tools/bpf/bpftool/Documentation/*.8 \
+		$(toolsman)/man8
+	install -m644 $(builddir)/tools/tools/bpf/bpftool/bash-completion/bpftool \
+		$(toolsbashcomp)
+
+	install -m755 debian/tools/generic $(toolsbin)/x86_energy_perf_policy
+	install -m755 debian/tools/generic $(toolsbin)/turbostat
+
+	cd $(builddir)/tools/tools/perf && make man
+	install -m644 $(builddir)/tools/tools/perf/Documentation/*.1 \
+		$(toolsman)/man1
+
+	install -m644 $(CURDIR)/tools/power/x86/x86_energy_perf_policy/*.8 $(toolsman)/man8
+	install -m644 $(CURDIR)/tools/power/x86/turbostat/*.8 $(toolsman)/man8
+
+ifeq ($(do_cloud_tools),true)
+ifeq ($(do_tools_hyperv),true)
+	install -d $(cloudsbin)
+	install -m755 debian/tools/generic $(cloudsbin)/hv_kvp_daemon
+	install -m755 debian/tools/generic $(cloudsbin)/hv_vss_daemon
+	install -m755 debian/tools/generic $(cloudsbin)/hv_fcopy_daemon
+	install -m755 debian/tools/generic $(cloudsbin)/lsvmbus
+	install -m755 debian/cloud-tools/hv_get_dhcp_info $(cloudsbin)
+	install -m755 debian/cloud-tools/hv_get_dns_info $(cloudsbin)
+	install -m755 debian/cloud-tools/hv_set_ifconfig $(cloudsbin)
+
+	install -d $(cloudman)/man8
+	install -m644 $(CURDIR)/tools/hv/*.8 $(cloudman)/man8
+endif
+endif
+
+ifeq ($(do_tools_acpidbg),true)
+	install -m755 debian/tools/generic $(toolsbin)/acpidbg
+endif
+
+endif
+
+ifeq ($(do_tools_host),true)
+	install -d $(hosttoolsbin)
+	install -d $(hosttoolsman)/man1
+	install -d $(hosttoolssystemd)
+
+	install -m 755 $(CURDIR)/tools/kvm/kvm_stat/kvm_stat $(hosttoolsbin)/
+	install -m 644 $(CURDIR)/tools/kvm/kvm_stat/kvm_stat.service \
+		$(hosttoolssystemd)/
+
+	cd $(builddir)/tools/tools/kvm/kvm_stat && make man
+	install -m644 $(builddir)/tools/tools/kvm/kvm_stat/*.1 \
+		$(hosttoolsman)/man1
+endif
+
+$(stampdir)/stamp-prepare-indep:
+	@echo Debug: $@
+	dh_prep -i
+	@touch $@
+
+install-indep: $(stampdir)/stamp-install-headers install-doc install-source install-tools
+	@echo Debug: $@
+
+# This is just to make it easy to call manually. Normally done in
+# binary-indep target during builds.
+binary-headers: $(stampdir)/stamp-prepare-indep $(stampdir)/stamp-install-headers
+	@echo Debug: $@
+	dh_installchangelogs -p$(indep_hdrpkg)
+	dh_installdocs -p$(indep_hdrpkg)
+	dh_compress -p$(indep_hdrpkg)
+	dh_fixperms -p$(indep_hdrpkg)
+	dh_installdeb -p$(indep_hdrpkg)
+	$(lockme) dh_gencontrol -p$(indep_hdrpkg)
+	dh_md5sums -p$(indep_hdrpkg)
+	dh_builddeb -p$(indep_hdrpkg)
+
+binary-indep: cloudpkg = $(cloud_common_pkg_name)
+binary-indep: hosttoolspkg = $(hosttools_pkg_name)
+binary-indep: install-indep
+	@echo Debug: $@
+	dh_installchangelogs -i
+	dh_installdocs -i
+	dh_compress -i
+	dh_fixperms -i
+ifeq ($(do_tools_common),true)
+ifeq ($(do_cloud_tools),true)
+ifeq ($(do_tools_hyperv),true)
+	dh_installinit -p$(cloudpkg) -n --name hv-kvp-daemon
+	dh_installinit -p$(cloudpkg) -n --name hv-vss-daemon
+	dh_installinit -p$(cloudpkg) -n --name hv-fcopy-daemon
+	dh_installudev -p$(cloudpkg) -n --name hv-kvp-daemon
+	dh_installudev -p$(cloudpkg) -n --name hv-vss-daemon
+	dh_installudev -p$(cloudpkg) -n --name hv-fcopy-daemon
+	dh_systemd_enable -p$(cloudpkg)
+	dh_installinit -p$(cloudpkg) -o --name hv-kvp-daemon
+	dh_installinit -p$(cloudpkg) -o --name hv-vss-daemon
+	dh_installinit -p$(cloudpkg) -o --name hv-fcopy-daemon
+	dh_systemd_start -p$(cloudpkg)
+endif
+	# Keep intel_sgx service disabled by default, so add it after dh_systemd_enable
+	# and dh_systemd_start are called:
+	dh_installinit -p$(cloudpkg) --no-start --no-enable --name intel-sgx-load-module
+endif
+endif
+ifeq ($(do_tools_host),true)
+	# Keep kvm_stat.service disabled by default (after dh_systemd_enable
+	# and dh_systemd_start:
+	dh_installinit -p$(hosttoolspkg) --no-enable --no-start --name kvm_stat
+endif
+	dh_installdeb -i
+	$(lockme) dh_gencontrol -i
+	dh_md5sums -i
+	dh_builddeb -i
--- linux-xilinx-zynqmp-5.15.0.orig/debian/rules.d/4-checks.mk
+++ linux-xilinx-zynqmp-5.15.0/debian/rules.d/4-checks.mk
@@ -0,0 +1,21 @@
+# Check the signature of staging modules
+module-signature-check-%: $(stampdir)/stamp-install-%
+	@echo Debug: $@
+	$(DROOT)/scripts/module-signature-check "$*" \
+		"$(DROOT)/$(mods_pkg_name)-$*" \
+		"$(DROOT)/$(mods_extra_pkg_name)-$*"
+
+checks-%: module-signature-check-%
+	@echo Debug: $@
+
+# Check the config against the known options list.
+config-prepare-check-%: $(stampdir)/stamp-prepare-tree-%
+	@echo Debug: $@
+	if [ -e $(commonconfdir)/config.common.ubuntu ]; then \
+		perl -f $(DROOT)/scripts/config-check \
+			$(builddir)/build-$*/.config "$(arch)" "$*" "$(commonconfdir)" \
+			"$(skipconfig)" "$(do_enforce_all)"; \
+	else \
+		python3 $(DROOT)/scripts/misc/annotations -f $(commonconfdir)/annotations \
+			--arch $(arch) --flavour $* --check $(builddir)/build-$*/.config; \
+	fi
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/config-check
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/config-check
@@ -0,0 +1,163 @@
+#!/usr/bin/perl
+#
+# check-config -- check the current config for issues
+#
+use strict;
+use File::Basename;
+use File::Spec;
+
+my $P = 'check-config';
+
+my $test = -1;
+if ($ARGV[0] eq '--test') {
+	$test = $ARGV[1] + 0;
+} elsif ($#ARGV != 5) {
+	die "Usage: $P <config> <arch> <flavour> <commonconfig> <warn-only> <enforce-all>\n";
+}
+
+my ($configfile, $arch, $flavour, $commonconfig, $warn_only, $enforce_all) = @ARGV;
+
+my %values = ();
+
+# If we are in overridden then still perform the checks and emit the messages
+# but do not return failure.  Those items marked FATAL will alway trigger
+# failure.
+my $fail_exit = 1;
+$fail_exit = 0 if ($warn_only eq 'true' || $warn_only eq '1');
+my $exit_val = 0;
+
+$enforce_all = 0 if $enforce_all eq "no" or $enforce_all eq "false";
+
+# Load up the current configuration values -- FATAL if this fails
+print "$P: $configfile: loading config\n";
+open(CONFIG, "<$configfile") || die "$P: $configfile: open failed -- $! -- aborting\n";
+while (<CONFIG>) {
+	# Pull out values.
+	/^#*\s*(CONFIG_\w+)[\s=](.*)$/ or next;
+	if ($2 eq 'is not set') {
+		$values{$1} = 'n';
+	} else {
+		$values{$1} = $2;
+	}
+}
+close(CONFIG);
+
+sub read_annotations {
+    my ($filename) = @_;
+    my %annot;
+    my $form = 1;
+    my ($config, $value, $options);
+
+    # Keep track of the configs that shouldn't be appended because
+    # they were include_annot from another annotations file.
+    # That's a hash of undefs, aka a set.
+    my %noappend;
+
+    print "$P: $filename loading annotations\n";
+    open(my $fd, "<$filename") ||
+	die "$P: $filename: open failed -- $! -- aborting\n";
+    while (<$fd>) {
+	if (/^# FORMAT: (\S+)/) {
+	    die "$P: $1: unknown annotations format\n" if ($1 < 2 || $1 > 4);
+	    $form = $1;
+	}
+
+	# Format #3 and #4 add the include directive on top of format #2:
+	if ($form >= 3 && /^\s*include(\s|$)/) {
+	    # Include quoted or unquoted files:
+	    if (/^\s*include\s+"(.*)"\s*$/ || /^\s*include\s+(.*)$/) {
+		# The include is relative to the current file
+		my $include_filename = File::Spec->join(dirname($filename), $1);
+		# Append the include files
+		my %include_annot = read_annotations($include_filename);
+		%annot = ( %annot, %include_annot );
+		# And marked them to not be appended:
+		my %included_noappend;
+		# Discard the values and keep only the keys
+		@included_noappend{keys %include_annot} = ();
+		%noappend = ( %noappend, %included_noappend );
+		next;
+	    } else {
+		die "$P: Invalid include: $_";
+	    }
+	}
+
+	/^#/ && next;
+	chomp;
+	/^$/ && next;
+	/^CONFIG_/ || next;
+
+	if ($form == 1) {
+	    ($config, $value, $options) = split(' ', $_, 3);
+	} elsif ($form >= 2) {
+	    ($config, $options) = split(' ', $_, 2);
+	}
+
+	if (exists $noappend{$config}) {
+	    delete $annot{$config};
+	    delete $noappend{$config};
+	}
+	$annot{$config} = $annot{$config} . ' ' . $options;
+    }
+    close($fd);
+    return %annot;
+}
+
+# ANNOTATIONS: check any annotations marked for enforcement
+my $annotations = "$commonconfig/annotations";
+my %annot = read_annotations($annotations);
+
+my $pass = 0;
+my $total = 0;
+my ($config, $value, $options, $option, $check, $policy);
+for $config (keys %annot) {
+	$check = $enforce_all;
+	$options = $annot{$config};
+
+	$policy = undef;
+	while ($options =~ /\s*([^\s<]+)<(.*?)?>/g) {
+		($option, $value) = ($1, $2);
+
+		if ($option eq 'mark' && $value eq 'ENFORCED') {
+			$check = 1;
+
+		} elsif ($option eq 'policy') {
+			if ($value =~ /^{/) {
+				$value =~ s/:/=>/g;
+				$policy = eval($value);
+				warn "$config: $@" if ($@);
+			} else {
+				$policy = undef;
+			}
+		}
+	}
+	if ($check == 1 && !defined($policy)) {
+		print "$P: INVALID POLICY (use policy<{...}>) $config$options\n";
+		$total++;
+		$check = 0;
+	}
+	if ($check) {
+		# CONFIG_VERSION_SIGNATURE is dynamically set during the build
+		next if ($config eq "CONFIG_VERSION_SIGNATURE");
+		my $is = '-';
+		$is = $values{$config} if (defined $values{$config});
+
+		my $value = '-';
+		for my $which ("$arch-$flavour", "$arch-*", "*-$flavour", "$arch", "*") {
+			if (defined $policy->{$which}) {
+				$value = $policy->{$which};
+				last;
+			}
+		}
+		if ($is eq $value) {
+			$pass++;
+		} else {
+			print "$P: FAIL ($is != $value): $config$options\n";
+			$exit_val = $fail_exit;
+		}
+		$total++;
+	}
+}
+
+print "$P: $pass/$total checks passed -- exit $exit_val\n";
+exit $exit_val;
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/control-create
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/control-create
@@ -0,0 +1,67 @@
+#!/bin/bash
+
+. debian/debian.env
+
+vars=$1
+any_signed=$2
+
+. $vars
+
+[ "$provides" != '' ] && provides="$provides, "
+
+if [ "$is_sub" = "" ]; then
+	flavour=$(basename $vars | sed 's/.*\.//')
+	stub="${DEBIAN}/control.d/flavour-control.stub debian/control.d/flavour-buildinfo.stub"
+	if [ "$any_signed" = 'true' ]; then
+		sign_me_pkg="-unsigned"
+		sign_me_txt=" unsigned"
+		sign_peer_pkg=""
+	else
+		sign_me_pkg=""
+		sign_me_txt=""
+		sign_peer_pkg="-unsigned"
+	fi
+else
+	flavour=$(basename $vars .vars)
+	stub=${DEBIAN}/sub-flavours/control.stub
+fi
+
+cat $stub | grep -v '^#' | sed \
+	-e "s#FLAVOUR#$flavour#g"		\
+	-e "s#DESC#$desc#g"			\
+	-e "s#ARCH#$arch#g"			\
+	-e "s#SUPPORTED#$supported#g"		\
+	-e "s#TARGET#$target#g"			\
+	-e "s#BOOTLOADER#$bootloader#g" 	\
+	-e "s#=PROVIDES=#$provides#g"		\
+	-e "s#=CONFLICTS=#$conflicts#g"		\
+	-e "s#=SIGN-ME-PKG=#$sign_me_pkg#g"	\
+	-e "s#=SIGN-ME-TXT=#$sign_me_txt#g"	\
+	-e "s#=SIGN-PEER-PKG=#$sign_peer_pkg#g"
+
+while read package version extras
+do
+	module="$package"
+	module_type=
+
+	# Module arch parameters are skipped here, so a package section will
+	# be generated for each flavour, and its Architecture will be set to
+	# all architectures with that flavour. Even that is being generated,
+	# it doesn't follow all of them will be built. That's to work-around
+	# dkms_exclude/dkms_include that manipulates supported architectures
+	# in $(DEBIAN)/rules.d/$(arch).mk.
+	for param in $extras; do
+		case "$param" in
+		modulename=*) module="${param#modulename=}" ;;
+		type=*) module_type="${param#type=}" ;;
+		*) continue ;;
+		esac
+	done
+
+	[ "$module_type" = "standalone" ] || continue
+
+	cat debian/control.d/flavour-module.stub | grep -v '^#' | sed	\
+		-e "s#ARCH#$arch#g"		\
+		-e "s#MODULE#$module#g"		\
+		-e "s#FLAVOUR#$flavour#g"
+done <"${DEBIAN}/dkms-versions"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/dkms-build
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/dkms-build
@@ -0,0 +1,261 @@
+#!/bin/sh
+set -e
+
+dkms_dir="$1"
+abi_flavour="$2"
+sign="$3"
+pkgname="$4"
+pkgdir="$5"
+dbgpkgdir="$6"
+package="$7"
+shift 7
+
+here=$(dirname "$(readlink -f "${0}")")
+
+srcdir=$(pwd)
+cd "$dkms_dir" || exit 1
+
+built_using_record()
+{
+	local subst="$1"
+	local built_using="$2"
+	if [ ! -f "$subst" ]; then
+		touch "$subst"
+	fi
+	if ! grep -q -s "^linux:BuiltUsing=" "$subst"; then
+		echo "linux:BuiltUsing=" >>"$subst"
+	fi
+	sed -i -e "s/^\(linux:BuiltUsing=.*\)/\1$built_using, /" "$subst"
+}
+
+# ABI: returns present in $? and located path in lpackage_path when found.
+package_present()
+{
+	for lpackage_path in "$1"_*.deb
+	do
+		break
+	done
+	[ -f "$lpackage_path" ]
+}
+
+# Download and extract the DKMS package -- note there may be more
+# than one package to install.
+for package_path in "$@"
+do
+	package_file=$(basename "$package_path")
+	echo "II: dkms-build downloading $package ($package_file)"
+	rpackage=$( echo "$package_path" | sed -e 's@.*/@@' -e 's@_.*@@' )
+	lpackage=$( echo "$rpackage" | sed -e 's@=.*@@' )
+
+	while true
+	do
+		if package_present "$lpackage"; then
+			break
+		fi
+		case "$package_path" in
+		pool/*)
+			# Attempt download from the launchpad librarian first.
+			"$here/file-downloader" "https://launchpad.net/ubuntu/+archive/primary/+files/$package_file" || true
+			if package_present "$lpackage"; then
+				break
+			fi
+
+			# Download from the available pools.
+			for pool in $( grep -h '^deb ' /etc/apt/sources.list /etc/apt/sources.list.d/*.list | awk '{print $2}' | sort -u )
+			do
+				if package_present "$lpackage"; then
+					break
+				fi
+				url="$pool/$package_path"
+				"$here/file-downloader" "$url" && break || true
+				# No components in PPAs.
+				url=$(echo "$url" | sed -e 's@/pool/[^/]*/@/pool/main/@')
+				"$here/file-downloader" "$url" && break || true
+			done
+			;;
+		http*:*)
+			"$here/file-downloader" "$package_path"
+			;;
+		*/*)
+			cp -p "$package_path" .
+			;;
+		*)
+			apt-get download "$rpackage"
+			;;
+		esac
+		break
+	done
+	if ! package_present "$lpackage"; then
+		echo "EE: $lpackage not found"
+		exit 1
+	fi
+
+	dpkg -x "$lpackage"_*.deb "$package"
+
+	lversion=$( echo "$lpackage_path" | sed -e 's@.*/@@' -e 's@_[^_]*$@@' -e 's@.*_@@')
+	#built_using_record "$srcdir/debian/$pkgname.substvars" "$built_using$lpackage (= $lversion)"
+done
+
+# Pick out the package/version from the dkms.conf.
+for dkms_conf in "$package/usr/src"/*/"dkms.conf"
+do
+	break
+done
+
+# It seems some packages have a # in the name which works fine if the
+# package is installed directly, but not so much if we build it out
+# of the normal location.
+sed -i -e '/^PACKAGE_NAME=/ s/#//g' "$dkms_conf"
+
+# Run any dkms-package specfic configuration steps
+dkms_config_specific="$srcdir/$0-configure--$package"
+dkms_config_generic=$(echo "$dkms_config_specific" | sed -e 's/-[0-9][0-9]*$/-N/')
+for dkms_config in "$dkms_config_specific" "$dkms_config_generic"
+do
+	if [ -z "$dkms_config" -o ! -e "$dkms_config" ]; then
+		continue
+	fi
+	echo "II: dkms-build-configure $(basename "$dkms_config") found, executing"
+	"$dkms_config" \
+		"$srcdir" \
+		"$dkms_conf" \
+		"$dkms_dir" \
+		"$abi_flavour" \
+		"$sign" \
+		"$pkgname" \
+		"$pkgdir" \
+		"$dbgpkgdir" \
+		"$package" \
+		"$@" || exit 1
+	break
+done
+
+cat - <<'EOF' >>"$dkms_conf"
+POST_BUILD="ubuntu-save-objects ${dkms_tree}/${PACKAGE_NAME}/${PACKAGE_VERSION}/build ${dkms_tree}/${PACKAGE_NAME}/${PACKAGE_VERSION}/objects $POST_BUILD"
+EOF
+ubuntu_script="$(dirname "$dkms_conf")/ubuntu-save-objects"
+cat - <<'EOF' >"$ubuntu_script"
+#!/bin/sh
+from="$1"
+to="$2"
+script="$3"
+shift 2
+
+# Copy the objects.
+echo "II: copying objects to '$to'"
+mkdir -p "$to"
+(cd "$from" && find -name \*.o -o -name \*.o.ur-\* | cpio -Lpd "$to")
+
+# Call the original post_install script if there is one.
+[ "$script" = '' ] && exit 0
+
+shift
+exec "$(dirname "$0")/$script" "$@"
+EOF
+chmod +x "$ubuntu_script"
+dkms_package=$( sed -ne 's/PACKAGE_NAME="\(.*\)"/\1/p' "$dkms_conf" )
+dkms_version=$( sed -ne 's/PACKAGE_VERSION="\(.*\)"/\1/p' "$dkms_conf" )
+
+# Build the DKMS binaries.
+echo "II: dkms-build building $package"
+fakeroot=""
+[ $(id -u) -ne 0 ] && fakeroot="/usr/bin/fakeroot"
+rc=0
+$fakeroot /usr/sbin/dkms build --no-prepare-kernel --no-clean-kernel \
+	-k "$abi_flavour" \
+	--sourcetree "$dkms_dir/source" \
+	--dkmstree "$dkms_dir/build" \
+	--kernelsourcedir "$dkms_dir/headers/linux-headers-$abi_flavour" \
+	"$dkms_conf" || rc=1
+
+# Find the log and add it to our own.
+for log in "$dkms_dir/build/$dkms_package/$dkms_version/$abi_flavour"/*/"log/make.log" "$dkms_dir/build/$dkms_package/$dkms_version/build/make.log"
+do
+	[ -f "$log" ] && break
+done
+sed -e "s@$dkms_dir@<<DKMSDIR>>@g" <"$log"
+
+# If this build failed then exit here.
+[ "$rc" != 0 ] && exit "$rc"
+
+# Install the modules with debug symbols we possibly built,
+# and strip the original modules for the next install step.
+if [ -n "$dbgpkgdir" ]; then
+	dbgpkgdir="$dbgpkgdir/$package"
+	echo "II: dkms-build installing $package into $dbgpkgdir (debug symbols)"
+	install -d "$dbgpkgdir"
+	find "$dkms_dir/build/$dkms_package/$dkms_version/$abi_version" -name \*.ko |
+	while read module; do
+		vmodule=$( basename "$module" )
+
+		# Check for '.debug_info' section in order to copy module.
+		# Useful if debug symbols are requested but not built for
+		# any reason (including not yet supported by DKMS package).
+		# Strip module just in case even if section isn't present.
+		if ${CROSS_COMPILE}objdump -h -j '.debug_info' "$module" >/dev/null 2>&1
+		then
+			echo "copying $vmodule"
+			cp "$module" "$dbgpkgdir"
+		else
+			echo "ignoring $vmodule (missing debug symbols)"
+		fi
+
+		# Just 'strip -g' as '/usr/sbin/dkms' does.
+		echo "stripping $vmodule"
+		strip -g "$module"
+	done
+fi
+
+# Install and optionally sign the modules we have built.
+pkgdir="$pkgdir/$package"
+echo "II: dkms-build installing $package into $pkgdir"
+install -d "$pkgdir"
+find "$dkms_dir/build/$dkms_package/$dkms_version/$abi_version" -name \*.ko |
+while read module; do
+	vmodule=$( basename "$module" )
+	case "$sign" in
+	--*)
+		echo "copying $vmodule"
+		cp "$module" "$pkgdir"
+		;;
+	*)
+		echo "signing $vmodule"
+		$sign "$module" "$pkgdir/$vmodule"
+		;;
+	esac
+done
+
+find "$dkms_dir/build/$dkms_package/$dkms_version/objects" -name \*.o -print | \
+while read object
+do
+	"$srcdir/debian/scripts/fix-filenames" "$object" "$dkms_dir"
+done
+
+# Finally see if there is a dkms-package specific post processor present.  Hand
+# it the original source directory, destination package directory, the objects
+# as squirreled away, and the log in case it is useful.  Finally pass a formed
+# signing command line in case we need to do that.
+dkms_build_specific="$srcdir/$0--$package"
+dkms_build_generic=$(echo "$dkms_build_specific" | sed -n -e 's/-[0-9][0-9]*[a-z]*$/-N/p')
+for dkms_build in "$dkms_build_specific" "$dkms_build_generic"
+do
+	if [ -z "$dkms_build" -o ! -e "$dkms_build" ]; then
+		continue
+	fi
+	echo "II: dkms-build override $(basename "$dkms_build") found, executing"
+	"$dkms_build" \
+		"$srcdir" \
+		"$dkms_dir/build/$dkms_package/$dkms_version/objects" \
+		"$log" \
+		"$dkms_dir" \
+		"$abi_flavour" \
+		"$sign" \
+		"$pkgname" \
+		"$pkgdir" \
+		"$dbgpkgdir" \
+		"$package" \
+		"$@" || exit 1
+	break
+done
+
+echo "II: dkms-build build $package complete"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/dkms-build--nvidia-N
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/dkms-build--nvidia-N
@@ -0,0 +1,113 @@
+#!/bin/sh
+set -e
+
+srcdir="$1"
+objects="$2"
+log="$3"
+shift 3
+
+dkms_dir="$1"
+abi_flavour="$2"
+sign="$3"
+pkgname="$4"
+pkgdir="$5"
+dbgpkgdir="$6"
+package="$7"
+shift 7
+
+build="$( dirname "$objects" )/build"
+
+# Copy over the objects ready for reconstruction.  The objects copy contains
+# the *.o files and the *.o-ur* retpoline files to allow the kernel to track
+# any retpoline sequences therein.  For our purposes we only want the *.o
+# files, elide the rest.
+mkdir -p "$pkgdir/bits/scripts"
+(
+	gcc_variant1=$(gcc --version | head -1 | sed -e 's/^gcc/GCC:/')
+	gcc_variant2=$(gcc --version | head -1 | sed -e 's/^\(gcc\) \((.*)\) \(.*\)$/\1 version \3 \2/')
+	cd "$objects" || exit 1
+	find -name \*.o | \
+	while read file
+	do
+		cp --parents "$file" "$pkgdir/bits"
+		"$srcdir/debian/scripts/fix-filenames" "$pkgdir/bits/$file" "$gcc_variant1"
+		"$srcdir/debian/scripts/fix-filenames" "$pkgdir/bits/$file" "$gcc_variant2"
+	done
+)
+
+# Install the support files we need.
+echo "II: copying support files ..."
+for lds_src in \
+	"$dkms_dir/headers/linux-headers-$abi_flavour/scripts/module.lds" \
+	"/usr/src/linux-headers-$abi_flavour/scripts/module.lds" \
+	"$dkms_dir/headers/linux-headers-$abi_flavour/scripts/module-common.lds" \
+	"/usr/src/linux-headers-$abi_flavour/scripts/module-common.lds"
+do
+	[ ! -f "$lds_src" ] && continue
+	echo "II: copying support files ... found $lds_src"
+	cp "$lds_src" "$pkgdir/bits/scripts"
+	break
+done
+
+# Build helper scripts.
+cat - <<'EOL' >"$pkgdir/bits/BUILD"
+[ "$1" = "unsigned" ] && { signed_only=:; shift; }
+[ "$1" = "nocheck" ] && { check_only=:; shift; }
+EOL
+grep /usr/bin/ld.bfd "$log" | grep -v scripts/genksyms/genksyms | sed -e "s@$build/@@g" >>"$pkgdir/bits/BUILD"
+sed -e 's/.*-o  *\([^ ]*\) .*/rm -f \1/g' <"$pkgdir/bits/BUILD" >"$pkgdir/bits/CLEAN"
+
+# As the builds contain the absolute filenames as used.  Use RECONSTRUCT to
+# rebuild the .ko's, sign them, pull off the signatures and then finally clean
+# up again.
+(
+	cd "$pkgdir/bits" || exit 1
+
+	# Add checksum check.
+	echo "\$check_only sha256sum -c SHA256SUMS || exit 1" >>"$pkgdir/bits/BUILD"
+
+	# Add .ko handling to the CLEAN/BUILD dance.
+	for ko in "$pkgdir"/*.ko
+	do
+		ko=$(basename "$ko")
+		echo "\$signed_only cat '$ko' '$ko.sig' >'../$ko'" >>"$pkgdir/bits/BUILD"
+		echo "\$signed_only rm -f '$ko'" >>"$pkgdir/bits/BUILD"
+		echo "rm -f '../$ko'" >>"$pkgdir/bits/CLEAN"
+	done
+
+	# Clear out anything we are not going to distribute and build unsigned .kos.
+	sh ./CLEAN
+	sh ./BUILD unsigned nocheck
+
+	if [ "$sign" = "--custom" ]; then
+		# We are building for and archive custom signing upload.  Keep everything.
+		:
+	elif [ "$sign" = "--lrm" ]; then
+		# We are in the LRM build; grab sha256 checksums and clean up.
+		sha256sum -b *.ko >"SHA256SUMS"
+		sh ./CLEAN
+
+	else
+		# We are in the main kernel, put the .kos together as we will
+		# on the users machine, sign them, and keep just the signature.
+		: >"SHA256SUMS"
+		for ko in *.ko
+		do
+			echo "detached-signature $ko"
+			$sign "$ko" "$ko.signed"
+			length=$( stat --format %s "$ko" )
+			dd if="$ko.signed" of="$ko.sig" bs=1 skip="$length" 2>/dev/null
+
+			rm -f "$ko.signed"
+			# Keep a checksum of the pre-signed object so we can check it is
+			# built correctly in LRM.
+			sha256sum -b "$ko" >>"SHA256SUMS"
+		done
+
+		# Clean out anything which not a signature.
+		mv "$pkgdir/bits/"*.sig "$pkgdir"
+		mv "$pkgdir/bits/SHA256SUMS" "$pkgdir"
+		find "$pkgdir" -name \*.sig -prune -o -name SHA256SUMS -prune -o -type f -print | xargs rm -f
+		find "$pkgdir" -depth -type d -print | xargs rmdir --ignore-fail-on-non-empty
+	fi
+) || exit "$?"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/dkms-build-configure--zfs
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/dkms-build-configure--zfs
@@ -0,0 +1,24 @@
+#!/bin/sh
+set -e
+
+srcdir="$1"
+dkms_conf="$2"
+shift 2
+
+dkms_dir="$1"
+abi_flavour="$2"
+sign="$3"
+pkgname="$4"
+pkgdir="$5"
+dbgpkgdir="$6"
+package="$7"
+shift 7
+
+# ZFS debug symbols are enabled in dkms.conf via PACKAGE_CONFIG file.
+if [ -n "$dbgpkgdir" ]; then
+	echo "enable zfs debug symbols"
+	pkg_cfg="$(dirname "$dkms_conf")/pkg_cfg"
+	echo 'ZFS_DKMS_ENABLE_DEBUGINFO=yes' >"$pkg_cfg"
+	echo 'ZFS_DKMS_DISABLE_STRIP=yes'   >>"$pkg_cfg"
+	sed -i "s,^\(PACKAGE_CONFIG=\).*,\1$pkg_cfg," $dkms_conf
+fi
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/file-downloader
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/file-downloader
@@ -0,0 +1,34 @@
+#!/bin/sh
+
+if [ "$#" -ne 1 ]; then
+	echo "Usage: $0 <url>" 1>&2
+	exit 1
+fi
+url="$1"
+
+to=$(basename "$url")
+
+count=0
+what='fetching'
+while :
+do
+	if [ "$count" -eq 20 ]; then
+		echo "EE: excessive redirects" 1>&2
+		exit 1
+	fi
+	count=$(($count+1))
+
+	echo "II: $what $url"
+
+	curl --silent --fail --show-error "$url" -o "$to" -D "$to.hdr" || exit 1
+	redirect=$(awk '/^Location: / {gsub(/^[[:space:]]+|[[:space:]]+$/,"",$2); print $2;}' "$to.hdr")
+	[ -z "$redirect" ] && break
+	what='  following'
+
+	url=$(echo "$redirect" | sed -e 's@https://launchpadlibrarian.net/@http://launchpadlibrarian.net/@')
+	if [ "$redirect" != "$url" ]; then
+		echo "II:   fixing $redirect"
+	fi
+done
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/fix-filenames.c
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/fix-filenames.c
@@ -0,0 +1,80 @@
+/*
+ * fix-filenames: find a specified pathname prefix and remove it from
+ *                C strings.
+ *
+ * Copyright (C) 2018 Canonical Ltd.
+ * Author: Andy Whitcroft <apw@canonical.com>
+ */
+#include <stdlib.h>
+#include <stdio.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <string.h>
+#include <sys/mman.h>
+#include <sys/types.h>
+#include <sys/stat.h>
+#include <unistd.h>
+
+int
+main(int argc, char *argv[])
+{
+	int rc;
+	char *in_name;
+	char *prefix;
+	int prefix_len;
+	int in_fd;
+	struct stat in_info;
+	char *in;
+	off_t size;
+	int length;
+
+	if (argc != 3) {
+		fprintf(stderr, "Usage: %s <file> <prefix>\n", argv[0]);
+		exit(1);
+	}
+	in_name    = argv[1];
+	prefix     = argv[2];
+	prefix_len = strlen(prefix);
+
+	in_fd = open(in_name, O_RDWR);
+	if (in_fd < 0) {
+		perror("open input failed");
+		exit(1);
+	}
+
+	rc = fstat(in_fd, &in_info);
+	if (rc < 0) {
+		perror("fstat input failed");
+		exit(1);
+	}
+	size = in_info.st_size;
+
+	in = mmap((void *)0, size, PROT_READ|PROT_WRITE, MAP_SHARED, in_fd, (off_t)0);
+	if (!in) {
+		perror("mmap failed");
+		exit(1);
+	}
+
+	for (; size > 0; size--, in++) {
+		if (*in != *prefix)
+			continue;
+		if (strncmp(in, prefix, prefix_len) != 0)
+			continue;
+		/* In the case of an exact match there there is nothing to move. */
+		if (in[prefix_len] == '\0')
+			length = 0;
+		/* If this is a filename, strip the leading slash. */
+		else if (in[prefix_len] == '/')
+			length = strlen(in + prefix_len + 1) + 1;
+		/* Otherwise just keep the suffix. */
+		else
+			length = strlen(in + prefix_len) + 1;
+
+		/*
+		 * Copy the suffix portion down to the start and clear
+		 * the remainder of the space to 0.
+		 */
+		memmove(in, in + prefix_len + 1, length);
+		memset(in + length, '\0', prefix_len);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/link-headers
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/link-headers
@@ -0,0 +1,42 @@
+#!/bin/bash -e
+
+. debian/debian.env
+
+hdrdir="$1"
+symdir="$2"
+flavour="$3"
+
+echo "Symlinking and copying headers for $flavour..."
+
+excludes="( -path ./debian -prune -o -path ./${DEBIAN} -prune -o -path ./.git ) -prune -o"
+
+(
+find . $excludes  -type f \
+	\( -name 'Makefile*' -o -name 'Kconfig*' -o -name 'Kbuild*' -o \
+	-name '*.sh' -o -name '*.pl' -o -name '*.lds' \) -print
+find ./include ./scripts -name .gitignore -prune -o -type f -print
+find ./include -mindepth 1 -maxdepth 1 $excludes -type d -print
+) | (
+while read file; do
+	dir=$file
+	lastdir=$file
+
+	if [ -e "$hdrdir/$file" -o -L "$hdrdir/$file" ]; then
+		continue
+	fi
+
+	while [ ! -e "$hdrdir/$dir" -a ! -L "$hdrdir/$dir" ]; do
+		lastdir=$dir
+		dir=`dirname $dir`
+	done
+	# If the last item to exist is a symlink we assume all is good
+	if [ ! -L "$hdrdir/$dir" ]; then
+		# Turns things like "./foo" into "../"
+		deref="`echo -n $lastdir | sed -e 's/^\.//' -e's,/[^/]*,../,g'`"
+		item="`echo -n $lastdir | sed -e 's/^\.\///'`"
+		ln -s $deref$symdir/$item $hdrdir/$item
+	fi
+done
+)
+
+exit
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/annotations
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/annotations
@@ -0,0 +1,34 @@
+#!/usr/bin/env python3
+# -*- mode: python -*-
+
+# This file is not installed; it's just to run annotations from inside a source
+# distribution without installing it in the system.
+
+import sys
+
+# Prevent generating .pyc files on import
+#
+# We may end up adding these files to our git repos by mistake, so simply
+# prevent generating them in advance.
+#
+# There's a tiny performance penalty with this, because python needs to
+# re-generate the bytecode on-the-fly every time the script is executed, but
+# this overhead is absolutely negligible compared the rest of the kernel build
+# time.
+sys.dont_write_bytecode = True
+
+import os  # noqa: E402 Import not at top of file
+from kconfig import run  # noqa: E402 Import not at top of file
+
+
+# Update PATH to make sure that annotations can be executed directly from the
+# source directory.
+def update_path():
+    script_dir = os.path.dirname(os.path.abspath(__file__))
+    current_path = os.environ.get("PATH", "")
+    new_path = f"{script_dir}:{current_path}"
+    os.environ["PATH"] = new_path
+
+
+update_path()
+exit(run.main())
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/arch-has-odm-enabled.sh
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/arch-has-odm-enabled.sh
@@ -0,0 +1,30 @@
+#!/bin/sh
+# Evaluate whether arch ($1) will be built with do_odm_drivers set to true.
+set -e
+
+if [ "$1" = "" ]; then
+	# This would be set doing the actual kernel build
+	if [ "$KBUILD_VERBOSE" = "" ]; then
+		return 1
+	fi
+	case $ARCH in
+	x86)	ARCH=amd64;;
+	*)	;;
+	esac
+else
+	ARCH=$1
+fi
+
+TOPDIR=$(dirname $0)/../../..
+. $TOPDIR/debian/debian.env
+RULESDIR=$TOPDIR/$DEBIAN/rules.d
+
+do_odm_drivers=false
+for f in $ARCH.mk hooks.mk; do
+	eval $(cat $RULESDIR/$f | sed -n -e '/do_odm_drivers/s/ \+//gp')
+done
+if [ "$do_odm_drivers" != "true" ]; then
+	return 1
+fi
+
+return 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/final-checks
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/final-checks
@@ -0,0 +1,31 @@
+#!/bin/bash
+
+debian="$1"
+abi="$2"
+
+. "$debian/etc/kernelconfig"
+archs=$( awk '/^Architecture:/ { $1=""; for (i=1; i<=NF; i++) { if ($i != "all") { print $i }}}' debian/control | sort -u)
+
+fail=0
+
+failure()
+{
+	echo "EE: $@" 1>&2
+	fail=1
+}
+
+if [ -e $debian/config/config.common.ubuntu ]; then
+    if [ -d debian/certs ]; then
+        if ! grep -q '^CONFIG_SYSTEM_TRUSTED_KEYS="debian/canonical-certs.pem"$' $debian/config/config.common.ubuntu; then
+	    failure "'CONFIG_SYSTEM_TRUSTED_KEYS="debian/canonical-certs.pem"' is required"
+        fi
+    fi
+
+    if [ -d debian/revoked-certs ]; then
+        if ! grep -q '^CONFIG_SYSTEM_REVOCATION_KEYS="debian/canonical-revoked-certs.pem"$' $debian/config/config.common.ubuntu; then
+	    failure "'CONFIG_SYSTEM_REVOCATION_KEYS="debian/canonical-revoked-certs.pem"' is required"
+        fi
+    fi
+fi
+
+exit "$fail"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/find-missing-sauce.sh
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/find-missing-sauce.sh
@@ -0,0 +1,15 @@
+#!/bin/bash
+#
+# Find the 'UBUNTU: SAUCE:' patches that have been dropped from
+# the previous release.
+#
+PREV_REL=focal
+PREV_REPO=git://kernel.ubuntu.com/ubuntu/ubuntu-${PREV_REL}.git
+
+git fetch ${PREV_REPO} master-next
+git log --pretty=oneline FETCH_HEAD|grep SAUCE|while read c m;do echo $m;done |sort > $$.prev-rel
+git log --pretty=oneline |grep SAUCE|while read c m;do echo $m;done |sort > $$.curr-rel
+
+diff -u $$.prev-rel $$.curr-rel |grep "^-"
+rm -f $$.prev-rel $$.curr-rel
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/fw-to-ihex.sh
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/fw-to-ihex.sh
@@ -0,0 +1,18 @@
+#!/bin/bash
+
+F=$1
+if [ "$F" = "" ]
+then
+	echo You must supply a firmware file.
+	exit 1
+fi
+
+echo "unsigned char d[] = {" > $F.c
+hexdump -v -e '"\t" 8/1 "0x%02x, " "\n"' $F >> $F.c
+echo "};" >> $F.c
+sed -i 's/0x .*$//' $F.c
+
+O="`dirname $F`/`basename $F`.o"
+gcc -o $O -c $F.c
+objcopy -Oihex $F.o $F.ihex
+
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/gen-auto-reconstruct
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/gen-auto-reconstruct
@@ -0,0 +1,89 @@
+#!/bin/bash
+
+if [ "$#" -ne 3 ]; then
+	echo "Usage: $0 <orig tag>|<base release> <reconstruct> <options>" 1>&2
+	exit 1
+fi
+tag="$1"
+reconstruct="$2"
+options="$3"
+
+case "$tag" in
+v*)	;;
+*)	tag="v${tag%.*}" ;;
+esac
+
+# Validate the tag.
+count=$( git tag -l "$tag" | wc -l )
+if [ "$count" != 1 ]; then
+	echo "$0: $tag: tag invalid" 1>&2
+	exit 1
+fi
+
+#git ls-tree -r --full-tree HEAD | grep ^120 | \
+#while read mode type blobid name
+
+(
+	# Identify all new symlinks since the proffered tag.
+	echo "# Recreate any symlinks created since the orig."
+	git diff "$tag.." --raw --no-renames | awk '(/^:000000 120000/ && $5 == "A") { print $NF }' | \
+	while read name
+	do
+		link=$( readlink "$name" )
+
+		echo "[ ! -L '$name' ] && ln -sf '$link' '$name'"
+	done
+
+	# Identify files with execute permissions added since the proffered tag.
+	git diff "$tag.." --raw --no-renames | awk -F '[: \t]' '{print $2, $3, $NF }' | \
+	while IFS=" " read old new name
+	do
+		old=$( printf "0%s" $old )
+		new=$( printf "0%s" $new )
+		changed=$(( (old ^ new) & 0111 ))
+		if [ "$changed" -ne 0 ]; then
+			added=$(( new & 0111 ))
+			if [ "$added" -ne 0 ]; then
+				echo "chmod +x '$name'"
+                       elif [ "$new" -ne 0 ]; then
+				echo "chmod -x '$name'"
+			fi
+		fi
+	done
+
+       # Identify all removed files since the proffered tag.
+	echo "# Remove any files deleted from the orig."
+	git diff "$tag.." --raw --no-renames | awk '(/^:/ && $5 == "D") { print $NF }' | \
+	while read name
+	do
+		echo "rm -f '$name'"
+	done
+
+	# All done, make sure this does not complete in error.
+	echo "exit 0"
+) >"$reconstruct"
+
+(
+	# Identify all new symlinks since the proffered tag.
+	echo "# Ignore any symlinks created since the orig which are rebuilt by reconstruct."
+	git diff "$tag.." --raw --no-renames | awk '(/^:000000 120000/ && $5 == "A") { print $NF }' | \
+	while read name
+	do
+		echo "extend-diff-ignore=^$name\$"
+	done
+) >"$options.update"
+
+
+head='^## autoreconstruct -- begin$'
+foot='^## autoreconstruct -- end$'
+sed -i -e "
+	/$head/,/$foot/{
+		/$head/{
+			p;
+			r $options.update
+		};
+		/$foot/p;
+		d
+	}
+" "$options"
+rm -f "$options.update"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/git-ubuntu-log
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/git-ubuntu-log
@@ -0,0 +1,165 @@
+#!/usr/bin/env python3
+
+import sys
+
+import codecs
+import urllib.request
+import json
+
+import textwrap
+
+sys.stdin = codecs.getreader("utf-8")(sys.stdin.detach())
+sys.stdout = codecs.getwriter("utf-8")(sys.stdout.detach())
+
+entries = []
+
+
+def add_entry(entry):
+    global tracking_bug
+
+    if entry and 'ignore' not in entry:
+        combo = []
+        for bug in set(entry.get('bugs', [])):
+            combo.append(bug)
+        for cve in set(entry.get('cves', [])):
+            combo.append(cve)
+        combo = sorted(combo)
+
+        if len(combo) == 0:
+            if entry.get('subject', "").startswith('UBUNTU'):
+                combo = '__packaging__'
+            else:
+                combo = '__mainline__'
+        else:
+            if entry.get('subject', "") == 'UBUNTU: link-to-tracker: update tracking bug':
+                tracking_bug = combo
+            if combo not in keys:
+                keys.append(combo)
+
+        entry['key'] = combo
+        entries.append(entry)
+
+
+# Suck up the git log output and extract the information we need.
+keys = []
+tracking_bug = None
+entry = None
+subject_wait = False
+for line in sys.stdin:
+    if line.startswith('commit '):
+        add_entry(entry)
+        entry = {}
+        subject_wait = True
+
+    elif line.startswith('Author: '):
+        bits = line.strip().split(maxsplit=1)
+        entry['author'] = bits[1]
+
+    elif subject_wait and line.startswith('    '):
+        subject_wait = False
+        entry['subject'] = line.strip()
+
+    elif line.startswith('    BugLink: '):
+        bits = line.strip().split(maxsplit=2)
+        if len(bits) > 2:
+            # There is text after the URL, so use that (after stripping the
+            # enclosing characters)
+            entry.setdefault('bugs', []).append(bits[2][1:-1])
+        elif 'launchpad.net' in bits[1]:
+            # Extract the bug number from the launchpad URL
+            bits = bits[1].split('/')
+            entry.setdefault('bugs', []).append(bits[-1])
+
+    elif line.startswith('    CVE-'):
+        entry.setdefault('cves', []).append(line.strip())
+
+    elif line.startswith('    Ignore:'):
+        entry['ignore'] = True
+
+    elif line.startswith('    Properties:'):
+        for prop in line.strip().split()[1:]:
+            if prop in ('ignore', 'no-changelog'):
+                entry['ignore'] = True
+
+add_entry(entry)
+
+entries.reverse()
+
+# Go through the entries and clear out authors for upstream commits.
+for entry in entries:
+    if entry['subject'].startswith('UBUNTU:'):
+        entry['subject'] = entry['subject'][7:].strip()
+    else:
+        del entry['author']
+
+# Lump everything without a bug at the bottom.
+keys.append('__packaging__')
+keys.append('__mainline__')
+
+# Ensure we list the tracking bug updates first.
+if tracking_bug is not None:
+    keys.remove(tracking_bug)
+    keys.insert(0, tracking_bug)
+
+emit_nl = False
+for key in keys:
+    if key == '__packaging__':
+        title_set = ['Miscellaneous Ubuntu changes']
+    elif key == '__mainline__':
+        title_set = ['Miscellaneous upstream changes']
+    else:
+        title_set = []
+        for bug in key:
+            if bug.startswith('CVE-'):
+                title_set.append(bug)
+            elif bug.isdigit():
+                # Assume that it is an LP bug number if 'bug' contains only digits
+                bug_info = None
+
+                try:
+                    # urllib.request.urlcleanup()
+                    request = urllib.request.Request('https://api.launchpad.net/devel/bugs/' + bug)
+                    request.add_header('Cache-Control', 'no-cache')
+                    with urllib.request.urlopen(request) as response:
+                        data = response.read()
+                        bug_info = json.loads(data.decode('utf-8'))
+
+                    title = bug_info['title']
+                    if 'description' in bug_info:
+                        for line in bug_info['description'].split('\n'):
+                            if line.startswith('Kernel-Description:'):
+                                title = line.split(' ', 1)[1]
+
+                except urllib.error.HTTPError:
+                    title = 'INVALID or PRIVATE BUG'
+
+                title += ' (LP###' + bug + ')'
+                title_set.append(title)
+            else:
+                # Finally treat 'bug' itself as the title
+                title_set.append(bug)
+
+    emit_title = True
+    for entry in entries:
+        if entry['key'] != key:
+            continue
+
+        if emit_title:
+            if emit_nl:
+                print('')
+            emit_nl = True
+
+            title_lines = textwrap.wrap('#// '.join(title_set), 76)
+            print('  * ' + title_lines[0].replace('LP###', 'LP: #').replace('#//', ' //'))
+            for line in title_lines[1:]:
+                line = line.replace('LP###', 'LP: #').replace('#//', ' //')
+                print('    ' + line)
+
+            emit_title = False
+
+        if key != tracking_bug or (key == tracking_bug and entry['subject'] != "link-to-tracker: update tracking bug"):
+            title_lines = textwrap.wrap(entry['subject'], 76)
+            print('    - ' + title_lines[0])
+            for line in title_lines[1:]:
+                line = line.replace('LP###', 'LP: #')
+                print('      ' + line)
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/insert-changes
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/insert-changes
@@ -0,0 +1,42 @@
+#!/usr/bin/python3
+
+import os
+import sys
+
+from subprocess import check_output
+
+droot = 'debian'
+if len(sys.argv) > 1:
+    droot = sys.argv[1]
+
+debian = 'debian.master'
+if len(sys.argv) > 2:
+    debian = sys.argv[2]
+
+rules = os.path.join(droot, 'rules')
+changelog = os.path.join(debian, 'changelog')
+changelog_new = os.path.join(debian, 'changelog.new')
+
+# Generate the list of new changes
+changes = check_output(['make', '-s', '-f', rules, 'printchanges']).decode('UTF-8')
+
+# Insert the new changes into the changelog
+with open(changelog) as orig, open(changelog_new, 'w') as new:
+    printed = False
+    skip_newline = False
+    for line in orig:
+        if line.startswith('  CHANGELOG: '):
+            if not printed:
+                printed = True
+                if changes == '':
+                    skip_newline = True
+                    continue
+                new.write(changes)
+        else:
+            if skip_newline and line.strip() == '':
+                skip_newline = False
+                continue
+            new.write(line)
+
+# Replace the original changelog with the new one
+os.rename(changelog_new, changelog)
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/insert-mainline-changes
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/insert-mainline-changes
@@ -0,0 +1,42 @@
+#!/usr/bin/perl
+
+if ($#ARGV != 2) {
+	warn "Usage: $0 <changelog> <to> <range>\n";
+	die  "       $0 debian.master/changelog v3.2.3 v3.2.2..v3.2.3\n";
+}
+my ($changelog, $to, $range) = @ARGV;
+
+my @changes = ();
+
+push(@changes, "\n");
+push(@changes, "  [ Upstream Kernel Changes ]\n\n");
+push(@changes, "  * rebase to $to\n");
+
+open(LOG, "git log '$range'|") || die "$0: git log failed: - $!\n";
+while (<LOG>) {
+	if (m@BugLink: .*launchpad.net/.*/([0-9]+)\s$@) {
+		push(@changes, "    - LP: #$1\n");
+	}
+}
+close(LOG);
+
+open(CHANGELOG, "< $changelog") or die "Cannot open changelog";
+open(NEW, "> $changelog.new") or die "Cannot open new changelog";
+
+$printed = 3;
+while (<CHANGELOG>) {
+	if (/^  CHANGELOG: /) {
+		$printed--;
+		print NEW;
+		if ($printed == 0) {
+			print NEW @changes;
+		}
+		next;
+	}
+	print NEW;
+}
+
+close(NEW);
+close(CHANGELOG);
+
+rename("$changelog.new", "$changelog");
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/insert-ubuntu-changes
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/insert-ubuntu-changes
@@ -0,0 +1,83 @@
+#!/usr/bin/perl
+
+if ($#ARGV != 2 && $#ARGV != 3) {
+	die "Usage: $0 <changelog> <stop at> <start at> [<source changelog>]\n";
+}
+if ($#ARGV == 2) {
+	push(@ARGV, "debian.master/changelog")
+}
+my ($changelog, $end, $start, $source_changelog) = @ARGV;
+
+$end =~ s/^\D+//;
+$start =~ s/^\D+//;
+
+sub version_cmp($$) {
+	my @a = split(/[\.-]+/, $_[0]);
+	my @b = split(/[\.-]+/, $_[1]);
+	for (my $i = 1;; $i++) {
+		if (!defined $a[$i]) {
+			if (!defined $b[$i]) {
+				return 0;
+			}
+			return -1;
+		}
+		if (!defined $b[$i]) {
+			return 1;
+		}
+		if ($a[$i] < $b[$i]) {
+			return -1;
+		}
+		if ($a[$i] > $b[$i]) {
+			return 1;
+		}
+	}
+}
+
+my @changes = ();
+my $output = 0;
+open(CHG, "<$source_changelog") ||
+	open(CHG, "<debian/changelog") ||
+	die "$0: debian/changelog: open failed - $!\n";
+while (<CHG>) {
+	if (/^\S+\s+\((.*)\)/) {
+		if (version_cmp($1, $end) <= 0) {
+			last;
+		}
+		if ($1 eq $start) {
+			$output = 1;
+		}
+		if ($output) {
+			push(@changes, "\n  [ Ubuntu: $1 ]\n\n");
+			next;
+		}
+	}
+	next if ($output == 0);
+
+	next if (/^\s*$/);
+	next if (/^\s--/);
+	next if (/^\s\s[^\*\s]/);
+
+	push(@changes, $_);
+}
+close(CHG);
+
+open(CHANGELOG, "< $changelog") or die "Cannot open changelog";
+open(NEW, "> $changelog.new") or die "Cannot open new changelog";
+
+$printed = 3;
+while (<CHANGELOG>) {
+	if (/^  CHANGELOG: /) {
+		$printed--;
+		print NEW;
+		if ($printed == 0) {
+			print NEW @changes;
+		}
+		next;
+	}
+	print NEW;
+}
+
+close(NEW);
+close(CHANGELOG);
+
+rename("$changelog.new", "$changelog");
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/kconfig/annotations.py
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/kconfig/annotations.py
@@ -0,0 +1,522 @@
+# -*- mode: python -*-
+# python module to manage Ubuntu kernel .config and annotations
+# Copyright © 2022 Canonical Ltd.
+
+import json
+import re
+import shutil
+import tempfile
+
+from abc import abstractmethod
+from ast import literal_eval
+from os.path import dirname, abspath
+
+from kconfig.version import ANNOTATIONS_FORMAT_VERSION
+
+
+class Config:
+    def __init__(self, fname, do_include=True):
+        """
+        Basic configuration file object
+        """
+        self.fname = fname
+        self.config = {}
+        self.do_include = do_include
+
+        raw_data = self._load(fname)
+        self._parse(raw_data)
+
+    @staticmethod
+    def _load(fname: str) -> str:
+        with open(fname, "rt", encoding="utf-8") as fd:
+            data = fd.read()
+        return data.rstrip()
+
+    def __str__(self):
+        """Return a JSON representation of the config"""
+        return json.dumps(self.config, indent=4)
+
+    @abstractmethod
+    def _parse(self, data: str):
+        pass
+
+
+class KConfig(Config):
+    """
+    Parse a .config file, individual config options can be accessed via
+    .config[<CONFIG_OPTION>]
+    """
+
+    def _parse(self, data: str):
+        self.config = {}
+        for line in data.splitlines():
+            m = re.match(r"^# (CONFIG_.*) is not set$", line)
+            if m:
+                self.config[m.group(1)] = literal_eval("'n'")
+                continue
+            m = re.match(r"^(CONFIG_[A-Za-z0-9_]+)=(.*)$", line)
+            if m:
+                self.config[m.group(1)] = literal_eval("'" + m.group(2) + "'")
+                continue
+
+
+class Annotation(Config):
+    """
+    Parse body of annotations file
+    """
+
+    def __init__(self, fname, do_include=True, do_json=False):
+        self.do_json = do_json
+        super().__init__(fname, do_include=True)
+
+    def _parse_body(self, data: str, parent=True):
+        for line in data.splitlines():
+            # Replace tabs with spaces, squeeze multiple into singles and
+            # remove leading and trailing spaces
+            line = line.replace("\t", " ")
+            line = re.sub(r" +", " ", line)
+            line = line.strip()
+
+            # Ignore empty lines
+            if not line:
+                continue
+
+            # Catpure flavors of included files
+            if line.startswith("# FLAVOUR: "):
+                self.include_flavour += line.split(" ")[2:]
+                continue
+
+            # Ignore comments
+            if line.startswith("#"):
+                continue
+
+            # Handle includes (recursively)
+            m = re.match(r'^include\s+"?([^"]*)"?', line)
+            if m:
+                if parent:
+                    self.include.append(m.group(1))
+                if self.do_include:
+                    include_fname = dirname(abspath(self.fname)) + "/" + m.group(1)
+                    include_data = self._load(include_fname)
+                    self._parse_body(include_data, parent=False)
+                continue
+
+            # Handle policy and note lines
+            if re.match(r".* (policy|note)<", line):
+                try:
+                    conf = line.split(" ")[0]
+                    if conf in self.config:
+                        entry = self.config[conf]
+                    else:
+                        entry = {"policy": {}}
+
+                    match = False
+                    m = re.match(r".* policy<(.*?)>", line)
+                    if m:
+                        match = True
+                        # Update the previous entry considering potential overrides:
+                        #  - if the new entry is adding a rule for a new
+                        #    arch/flavour, simply add that
+                        #  - if the new entry is overriding a previous
+                        #    arch-flavour item, then overwrite that item
+                        #  - if the new entry is overriding a whole arch, then
+                        #    remove all the previous flavour rules of that arch
+                        new_entry = literal_eval(m.group(1))
+                        for key in new_entry:
+                            if key in self.arch:
+                                for flavour_key in list(entry["policy"].keys()):
+                                    if flavour_key.startswith(key):
+                                        del entry["policy"][flavour_key]
+                                entry["policy"][key] = new_entry[key]
+                            else:
+                                entry["policy"][key] = new_entry[key]
+
+                    m = re.match(r".* note<(.*?)>", line)
+                    if m:
+                        entry["oneline"] = match
+                        match = True
+                        entry["note"] = "'" + m.group(1).replace("'", "") + "'"
+
+                    if not match:
+                        raise SyntaxError("syntax error")
+                    self.config[conf] = entry
+                except Exception as e:
+                    raise SyntaxError(str(e) + f", line = {line}") from e
+                continue
+
+            # Invalid line
+            raise SyntaxError(f"invalid line: {line}")
+
+    def _legacy_parse(self, data: str):
+        """
+        Parse main annotations file, individual config options can be accessed
+        via self.config[<CONFIG_OPTION>]
+        """
+        self.config = {}
+        self.arch = []
+        self.flavour = []
+        self.flavour_dep = {}
+        self.include = []
+        self.header = ""
+        self.include_flavour = []
+
+        # Parse header (only main header will considered, headers in includes
+        # will be treated as comments)
+        for line in data.splitlines():
+            if re.match(r"^#.*", line):
+                m = re.match(r"^# ARCH: (.*)", line)
+                if m:
+                    self.arch = list(m.group(1).split(" "))
+                m = re.match(r"^# FLAVOUR: (.*)", line)
+                if m:
+                    self.flavour = list(m.group(1).split(" "))
+                m = re.match(r"^# FLAVOUR_DEP: (.*)", line)
+                if m:
+                    self.flavour_dep = literal_eval(m.group(1))
+                self.header += line + "\n"
+            else:
+                break
+
+        # Return an error if architectures are not defined
+        if not self.arch:
+            raise SyntaxError("ARCH not defined in annotations")
+        # Return an error if flavours are not defined
+        if not self.flavour:
+            raise SyntaxError("FLAVOUR not defined in annotations")
+
+        # Parse body
+        self._parse_body(data)
+
+        # Sanity check: Verify that all FLAVOUR_DEP flavors are valid
+        if self.do_include:
+            for src, tgt in self.flavour_dep.items():
+                if src not in self.flavour:
+                    raise SyntaxError(f"Invalid source flavour in FLAVOUR_DEP: {src}")
+                if tgt not in self.include_flavour:
+                    raise SyntaxError(f"Invalid target flavour in FLAVOUR_DEP: {tgt}")
+
+    def _json_parse(self, data, is_included=False):
+        data = json.loads(data)
+
+        # Check if version is supported
+        version = data["attributes"]["_version"]
+        if version > ANNOTATIONS_FORMAT_VERSION:
+            raise SyntaxError(f"annotations format version {version} not supported")
+
+        # Check for top-level annotations vs imported annotations
+        if not is_included:
+            self.config = data["config"]
+            self.arch = data["attributes"]["arch"]
+            self.flavour = data["attributes"]["flavour"]
+            self.flavour_dep = data["attributes"]["flavour_dep"]
+            self.include = data["attributes"]["include"]
+            self.include_flavour = []
+        else:
+            # We are procesing an imported annotations, so merge all the
+            # configs and attributes.
+            try:
+                self.config = data["config"] | self.config
+            except TypeError:
+                self.config = {**self.config, **data["config"]}
+            self.arch = list(set(self.arch) | set(data["attributes"]["arch"]))
+            self.flavour = list(set(self.flavour) | set(data["attributes"]["flavour"]))
+            self.include_flavour = list(set(self.include_flavour) | set(data["attributes"]["flavour"]))
+            self.flavour_dep = self.flavour_dep | data["attributes"]["flavour_dep"]
+
+        # Handle recursive inclusions
+        if self.do_include:
+            for f in data["attributes"]["include"]:
+                include_fname = dirname(abspath(self.fname)) + "/" + f
+                data = self._load(include_fname)
+                self._json_parse(data, is_included=True)
+
+    def _parse(self, data: str):
+        if self.do_json:
+            self._json_parse(data, is_included=False)
+        else:
+            self._legacy_parse(data)
+
+    def _remove_entry(self, config: str):
+        if self.config[config]:
+            del self.config[config]
+
+    def remove(self, config: str, arch: str = None, flavour: str = None):
+        if config not in self.config:
+            return
+        if arch is not None:
+            if flavour is not None:
+                flavour = f"{arch}-{flavour}"
+            else:
+                flavour = arch
+            del self.config[config]["policy"][flavour]
+            if not self.config[config]["policy"]:
+                self._remove_entry(config)
+        else:
+            self._remove_entry(config)
+
+    def set(
+        self,
+        config: str,
+        arch: str = None,
+        flavour: str = None,
+        value: str = None,
+        note: str = None,
+    ):
+        if value is not None:
+            if config not in self.config:
+                self.config[config] = {"policy": {}}
+            if arch is not None:
+                if flavour is not None:
+                    flavour = f"{arch}-{flavour}"
+                else:
+                    flavour = arch
+                self.config[config]["policy"][flavour] = value
+            else:
+                for a in self.arch:
+                    self.config[config]["policy"][a] = value
+        if note is not None:
+            self.config[config]["note"] = "'" + note.replace("'", "") + "'"
+
+    def update(self, c: KConfig, arch: str, flavour: str = None, configs: list = None):
+        """Merge configs from a Kconfig object into Annotation object"""
+
+        # Determine if we need to import all configs or a single config
+        if not configs:
+            configs = c.config.keys()
+            try:
+                configs |= self.search_config(arch=arch, flavour=flavour).keys()
+            except TypeError:
+                configs = {
+                    **configs,
+                    **self.search_config(arch=arch, flavour=flavour).keys(),
+                }
+
+        # Import configs from the Kconfig object into Annotations
+        flavour_arg = flavour
+        if flavour is not None:
+            flavour = arch + f"-{flavour}"
+        else:
+            flavour = arch
+        for conf in configs:
+            if conf in c.config:
+                val = c.config[conf]
+            else:
+                val = "-"
+            if conf in self.config:
+                if "policy" in self.config[conf]:
+                    # Add a TODO if a config with a note is changing and print
+                    # a warning
+                    old_val = self.search_config(config=conf, arch=arch, flavour=flavour_arg)
+                    if old_val:
+                        old_val = old_val[conf]
+                    if val != old_val and "note" in self.config[conf]:
+                        self.config[conf]["note"] = "TODO: update note"
+                        print(f"WARNING: {conf} changed from {old_val} to {val}, updating note")
+                    self.config[conf]["policy"][flavour] = val
+                else:
+                    self.config[conf]["policy"] = {flavour: val}
+            else:
+                self.config[conf] = {"policy": {flavour: val}}
+
+    def _compact(self):
+        # Try to remove redundant settings: if the config value of a flavour is
+        # the same as the one of the main arch simply drop it.
+        for conf in self.config.copy():
+            if "policy" not in self.config[conf]:
+                continue
+            for flavour in self.flavour:
+                if flavour not in self.config[conf]["policy"]:
+                    continue
+                m = re.match(r"^(.*?)-(.*)$", flavour)
+                if not m:
+                    continue
+                arch = m.group(1)
+                if arch in self.config[conf]["policy"]:
+                    if self.config[conf]["policy"][flavour] == self.config[conf]["policy"][arch]:
+                        del self.config[conf]["policy"][flavour]
+                        continue
+                if flavour not in self.flavour_dep:
+                    continue
+                generic = self.flavour_dep[flavour]
+                if generic in self.config[conf]["policy"]:
+                    if self.config[conf]["policy"][flavour] == self.config[conf]["policy"][generic]:
+                        del self.config[conf]["policy"][flavour]
+                        continue
+            # Remove rules for flavours / arches that are not supported (not
+            # listed in the annotations header).
+            for flavour in self.config[conf]["policy"].copy():
+                if flavour not in list(set(self.arch + self.flavour)):
+                    del self.config[conf]["policy"][flavour]
+            # Remove configs that are all undefined across all arches/flavours
+            # (unless we have includes)
+            if not self.include:
+                if "policy" in self.config[conf]:
+                    if list(set(self.config[conf]["policy"].values())) == ["-"]:
+                        self.config[conf]["policy"] = {}
+            # Drop empty rules
+            if not self.config[conf]["policy"]:
+                del self.config[conf]
+            else:
+                # Compact same value across all flavour within the same arch
+                for arch in self.arch:
+                    arch_flavours = [i for i in self.flavour if i.startswith(arch)]
+                    value = None
+                    for flavour in arch_flavours:
+                        if flavour not in self.config[conf]["policy"]:
+                            break
+                        if value is None:
+                            value = self.config[conf]["policy"][flavour]
+                        elif value != self.config[conf]["policy"][flavour]:
+                            break
+                    else:
+                        for flavour in arch_flavours:
+                            del self.config[conf]["policy"][flavour]
+                        self.config[conf]["policy"][arch] = value
+        # After the first round of compaction we may end up having configs that
+        # are undefined across all arches, so do another round of compaction to
+        # drop these settings that are not needed anymore
+        # (unless we have includes).
+        if not self.include:
+            for conf in self.config.copy():
+                # Remove configs that are all undefined across all arches/flavours
+                if "policy" in self.config[conf]:
+                    if list(set(self.config[conf]["policy"].values())) == ["-"]:
+                        self.config[conf]["policy"] = {}
+                # Drop empty rules
+                if not self.config[conf]["policy"]:
+                    del self.config[conf]
+
+    @staticmethod
+    def _sorted(config):
+        """Sort configs alphabetically but return configs with a note first"""
+        w_note = []
+        wo_note = []
+        for c in sorted(config):
+            if "note" in config[c]:
+                w_note.append(c)
+            else:
+                wo_note.append(c)
+        return w_note + wo_note
+
+    def save(self, fname: str):
+        """Save annotations data to the annotation file"""
+        # Compact annotations structure
+        self._compact()
+
+        # Save annotations to disk
+        with tempfile.NamedTemporaryFile(mode="w+t", delete=False) as tmp:
+            # Write header
+            tmp.write(self.header + "\n")
+
+            # Write includes
+            for i in self.include:
+                tmp.write(f'include "{i}"\n')
+            if self.include:
+                tmp.write("\n")
+
+            # Write config annotations and notes
+            tmp.flush()
+            shutil.copy(tmp.name, fname)
+            tmp_a = Annotation(fname)
+
+            # Only save local differences (preserve includes)
+            marker = False
+            for conf in self._sorted(self.config):
+                new_val = self.config[conf]
+                if "policy" not in new_val:
+                    continue
+
+                # If new_val is a subset of old_val, skip it unless there are
+                # new notes that are different than the old ones.
+                old_val = tmp_a.config.get(conf)
+                if old_val and "policy" in old_val:
+                    try:
+                        can_skip = old_val["policy"] == old_val["policy"] | new_val["policy"]
+                    except TypeError:
+                        can_skip = old_val["policy"] == {
+                            **old_val["policy"],
+                            **new_val["policy"],
+                        }
+                    if can_skip:
+                        if "note" not in new_val:
+                            continue
+                        if "note" in old_val and "note" in new_val:
+                            if old_val["note"] == new_val["note"]:
+                                continue
+
+                # Write out the policy (and note) line(s)
+                val = dict(sorted(new_val["policy"].items()))
+                line = f"{conf: <47} policy<{val}>"
+                if "note" in new_val:
+                    val = new_val["note"]
+                    if new_val.get("oneline", False):
+                        # Single line
+                        line += f" note<{val}>"
+                    else:
+                        # Separate policy and note lines,
+                        # followed by an empty line
+                        line += f"\n{conf: <47} note<{val}>\n"
+                elif not marker:
+                    # Write out a marker indicating the start of annotations
+                    # without notes
+                    tmp.write("\n# ---- Annotations without notes ----\n\n")
+                    marker = True
+                tmp.write(line + "\n")
+
+            # Replace annotations with the updated version
+            tmp.flush()
+            shutil.move(tmp.name, fname)
+
+    def search_config(self, config: str = None, arch: str = None, flavour: str = None) -> dict:
+        """Return config value of a specific config option or architecture"""
+        if flavour is None:
+            flavour = "generic"
+        flavour = f"{arch}-{flavour}"
+        if flavour in self.flavour_dep:
+            generic = self.flavour_dep[flavour]
+        else:
+            generic = flavour
+        if config is None and arch is None:
+            # Get all config options for all architectures
+            return self.config
+        if config is None and arch is not None:
+            # Get config options of a specific architecture
+            ret = {}
+            for c, val in self.config.items():
+                if "policy" not in val:
+                    continue
+                if flavour in val["policy"]:
+                    ret[c] = val["policy"][flavour]
+                elif generic != flavour and generic in val["policy"]:
+                    ret[c] = val["policy"][generic]
+                elif arch in val["policy"]:
+                    ret[c] = val["policy"][arch]
+            return ret
+        if config is not None and arch is None:
+            # Get a specific config option for all architectures
+            return self.config[config] if config in self.config else None
+        if config is not None and arch is not None:
+            # Get a specific config option for a specific architecture
+            if config in self.config:
+                if "policy" in self.config[config]:
+                    if flavour in self.config[config]["policy"]:
+                        return {config: self.config[config]["policy"][flavour]}
+                    if generic != flavour and generic in self.config[config]["policy"]:
+                        return {config: self.config[config]["policy"][generic]}
+                    if arch in self.config[config]["policy"]:
+                        return {config: self.config[config]["policy"][arch]}
+        return None
+
+    @staticmethod
+    def to_config(data: dict) -> str:
+        """Convert annotations data to .config format"""
+        s = ""
+        for c in data:
+            v = data[c]
+            if v == "n":
+                s += f"# {c} is not set\n"
+            elif v == "-":
+                pass
+            else:
+                s += f"{c}={v}\n"
+        return s.rstrip()
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/kconfig/run.py
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/kconfig/run.py
@@ -0,0 +1,370 @@
+# -*- mode: python -*-
+# Manage Ubuntu kernel .config and annotations
+# Copyright © 2022 Canonical Ltd.
+
+import sys
+import os
+import argparse
+import json
+from signal import signal, SIGPIPE, SIG_DFL
+
+try:
+    from argcomplete import autocomplete
+except ModuleNotFoundError:
+    # Allow to run this program also when argcomplete is not available
+    def autocomplete(_unused):
+        pass
+
+
+from kconfig.annotations import Annotation, KConfig  # noqa: E402 Import not at top of file
+from kconfig.utils import autodetect_annotations, arg_fail  # noqa: E402 Import not at top of file
+from kconfig.version import VERSION, ANNOTATIONS_FORMAT_VERSION  # noqa: E402 Import not at top of file
+
+
+SKIP_CONFIGS = (
+    # CONFIG_VERSION_SIGNATURE is dynamically set during the build
+    "CONFIG_VERSION_SIGNATURE",
+    # Allow to use a different versions of toolchain tools
+    "CONFIG_GCC_VERSION",
+    "CONFIG_CC_VERSION_TEXT",
+    "CONFIG_AS_VERSION",
+    "CONFIG_LD_VERSION",
+    "CONFIG_LLD_VERSION",
+    "CONFIG_CLANG_VERSION",
+    "CONFIG_PAHOLE_VERSION",
+    "CONFIG_RUSTC_VERSION_TEXT",
+    "CONFIG_BINDGEN_VERSION_TEXT",
+)
+
+
+def make_parser():
+    parser = argparse.ArgumentParser(
+        description="Manage Ubuntu kernel .config and annotations",
+    )
+    parser.add_argument("--version", "-v", action="version", version=f"%(prog)s {VERSION}")
+
+    parser.add_argument(
+        "--file",
+        "-f",
+        action="store",
+        help="Pass annotations or .config file to be parsed",
+    )
+    parser.add_argument("--arch", "-a", action="store", help="Select architecture")
+    parser.add_argument("--flavour", "-l", action="store", help='Select flavour (default is "generic")')
+    parser.add_argument("--config", "-c", action="store", help="Select a specific config option")
+    parser.add_argument("--query", "-q", action="store_true", help="Query annotations")
+    parser.add_argument(
+        "--note",
+        "-n",
+        action="store",
+        help="Write a specific note to a config option in annotations",
+    )
+    parser.add_argument(
+        "--autocomplete",
+        action="store_true",
+        help="Enable config bash autocomplete: `source <(annotations --autocomplete)`",
+    )
+    parser.add_argument(
+        "--source",
+        "-t",
+        action="store_true",
+        help="Jump to a config definition in the kernel source code",
+    )
+    parser.add_argument(
+        "--no-include",
+        action="store_true",
+        help="Do not process included annotations (stop at the main file)",
+    )
+    parser.add_argument(
+        "--json",
+        action="store_true",
+        help="Try to parse annotations file in pure JSON format",
+    )
+
+    ga = parser.add_argument_group(title="Action").add_mutually_exclusive_group(required=False)
+    ga.add_argument(
+        "--write",
+        "-w",
+        action="store",
+        metavar="VALUE",
+        dest="value",
+        help="Set a specific config value in annotations (use 'null' to remove)",
+    )
+    ga.add_argument(
+        "--export",
+        "-e",
+        action="store_true",
+        help="Convert annotations to .config format",
+    )
+    ga.add_argument(
+        "--import",
+        "-i",
+        action="store",
+        metavar="FILE",
+        dest="import_file",
+        help="Import a full .config for a specific arch and flavour into annotations",
+    )
+    ga.add_argument(
+        "--update",
+        "-u",
+        action="store",
+        metavar="FILE",
+        dest="update_file",
+        help="Import a partial .config into annotations (only resync configs specified in FILE)",
+    )
+    ga.add_argument(
+        "--check",
+        "-k",
+        action="store",
+        metavar="FILE",
+        dest="check_file",
+        help="Validate kernel .config with annotations",
+    )
+    return parser
+
+
+_ARGPARSER = make_parser()
+
+
+def export_result(data):
+    # Dump metadata / attributes first
+    out = '{\n  "attributes": {\n'
+    for key, value in sorted(data["attributes"].items()):
+        out += f'     "{key}": {json.dumps(value)},\n'
+    out = out.rstrip(",\n")
+    out += "\n  },"
+    print(out)
+
+    configs_with_note = {key: value for key, value in data["config"].items() if "note" in value}
+    configs_without_note = {key: value for key, value in data["config"].items() if "note" not in value}
+
+    # Dump configs, sorted alphabetically, showing items with a note first
+    out = '  "config": {\n'
+    for key in sorted(configs_with_note) + sorted(configs_without_note):
+        policy = data["config"][key]["policy"]
+        if "note" in data["config"][key]:
+            note = data["config"][key]["note"]
+            out += f'    "{key}": {{"policy": {json.dumps(policy)}, "note": {json.dumps(note)}}},\n'
+        else:
+            out += f'    "{key}": {{"policy": {json.dumps(policy)}}},\n'
+    out = out.rstrip(",\n")
+    out += "\n  }\n}"
+    print(out)
+
+
+def print_result(config, data):
+    if data is not None and config is not None and config not in data:
+        data = {config: data}
+    print(json.dumps(data, sort_keys=True, indent=2))
+
+
+def do_query(args):
+    if args.arch is None and args.flavour is not None:
+        arg_fail(_ARGPARSER, "error: --flavour requires --arch")
+    a = Annotation(args.file, do_include=(not args.no_include), do_json=args.json)
+    res = a.search_config(config=args.config, arch=args.arch, flavour=args.flavour)
+    # If no arguments are specified dump the whole annotations structure
+    if args.config is None and args.arch is None and args.flavour is None:
+        res = {
+            "attributes": {
+                "arch": a.arch,
+                "flavour": a.flavour,
+                "flavour_dep": a.flavour_dep,
+                "include": a.include,
+                "_version": ANNOTATIONS_FORMAT_VERSION,
+            },
+            "config": res,
+        }
+        export_result(res)
+    else:
+        print_result(args.config, res)
+
+
+def do_autocomplete(args):
+    a = Annotation(args.file)
+    res = (c.removeprefix("CONFIG_") for c in a.search_config())
+    res_str = " ".join(res)
+    print(f'complete -W "{res_str}" annotations')
+
+
+def do_source(args):
+    if args.config is None:
+        arg_fail(_ARGPARSER, "error: --source requires --config")
+    if not os.path.exists("tags"):
+        print("tags not found in the current directory, try: `make tags`")
+        sys.exit(1)
+    os.system(f"vim -t {args.config}")
+
+
+def do_note(args):
+    if args.config is None:
+        arg_fail(_ARGPARSER, "error: --note requires --config")
+
+    # Set the note in annotations
+    a = Annotation(args.file)
+    a.set(args.config, note=args.note)
+
+    # Save back to annotations
+    a.save(args.file)
+
+    # Query and print back the value
+    a = Annotation(args.file)
+    res = a.search_config(config=args.config)
+    print_result(args.config, res)
+
+
+def do_write(args):
+    if args.config is None:
+        arg_fail(_ARGPARSER, "error: --write requires --config")
+
+    # Set the value in annotations ('null' means remove)
+    a = Annotation(args.file)
+    if args.value == "null":
+        a.remove(args.config, arch=args.arch, flavour=args.flavour)
+    else:
+        a.set(
+            args.config,
+            arch=args.arch,
+            flavour=args.flavour,
+            value=args.value,
+            note=args.note,
+        )
+
+    # Save back to annotations
+    a.save(args.file)
+
+    # Query and print back the value
+    a = Annotation(args.file)
+    res = a.search_config(config=args.config)
+    print_result(args.config, res)
+
+
+def do_export(args):
+    if args.arch is None:
+        arg_fail(_ARGPARSER, "error: --export requires --arch")
+    a = Annotation(args.file)
+    conf = a.search_config(config=args.config, arch=args.arch, flavour=args.flavour)
+    if conf:
+        print(a.to_config(conf))
+
+
+def do_import(args):
+    if args.arch is None:
+        arg_fail(_ARGPARSER, "error: --arch is required with --import")
+    if args.flavour is None:
+        arg_fail(_ARGPARSER, "error: --flavour is required with --import")
+    if args.config is not None:
+        arg_fail(_ARGPARSER, "error: --config cannot be used with --import (try --update)")
+
+    # Merge with the current annotations
+    a = Annotation(args.file)
+    c = KConfig(args.import_file)
+    a.update(c, arch=args.arch, flavour=args.flavour)
+
+    # Save back to annotations
+    a.save(args.file)
+
+
+def do_update(args):
+    if args.arch is None:
+        arg_fail(_ARGPARSER, "error: --arch is required with --update")
+
+    # Merge with the current annotations
+    a = Annotation(args.file)
+    c = KConfig(args.update_file)
+    if args.config is None:
+        configs = list(set(c.config.keys()) - set(SKIP_CONFIGS))
+    if configs:
+        a.update(c, arch=args.arch, flavour=args.flavour, configs=configs)
+
+    # Save back to annotations
+    a.save(args.file)
+
+
+def do_check(args):
+    # Determine arch and flavour
+    if args.arch is None:
+        arg_fail(_ARGPARSER, "error: --arch is required with --check")
+
+    print(f"check-config: loading annotations from {args.file}")
+    total = good = ret = 0
+
+    # Load annotations settings
+    a = Annotation(args.file)
+    a_configs = a.search_config(arch=args.arch, flavour=args.flavour).keys()
+
+    # Parse target .config
+    c = KConfig(args.check_file)
+    c_configs = c.config.keys()
+
+    # Validate .config against annotations
+    for conf in sorted(a_configs | c_configs):
+        if conf in SKIP_CONFIGS:
+            continue
+        entry = a.search_config(config=conf, arch=args.arch, flavour=args.flavour)
+        expected = entry[conf] if entry else "-"
+        value = c.config[conf] if conf in c.config else "-"
+        if value != expected:
+            policy = a.config[conf] if conf in a.config else "undefined"
+            if "policy" in policy:
+                policy = f"policy<{policy['policy']}>"
+            print(f"check-config: {conf} changed from {expected} to {value}: {policy})")
+            ret = 1
+        else:
+            good += 1
+        total += 1
+
+    num = total - good
+    if ret:
+        if os.path.exists(".git"):
+            print(f"check-config: {num} config options have been changed, review them with `git diff`")
+        else:
+            print(f"check-config: {num} config options have changed")
+    else:
+        print("check-config: all good")
+    sys.exit(ret)
+
+
+def main():
+    # Prevent broken pipe errors when showing output in pipe to other tools
+    # (less for example)
+    signal(SIGPIPE, SIG_DFL)
+
+    # Main annotations program
+    autocomplete(_ARGPARSER)
+    args = _ARGPARSER.parse_args()
+
+    if args.file is None:
+        args.file = autodetect_annotations()
+        if args.file is None:
+            arg_fail(
+                _ARGPARSER,
+                "error: could not determine DEBDIR, try using: --file/-f",
+                show_usage=False,
+            )
+
+    if args.config and not args.config.startswith("CONFIG_"):
+        args.config = "CONFIG_" + args.config
+
+    if args.value:
+        do_write(args)
+    elif args.note:
+        do_note(args)
+    elif args.export:
+        do_export(args)
+    elif args.import_file:
+        do_import(args)
+    elif args.update_file:
+        do_update(args)
+    elif args.check_file:
+        do_check(args)
+    elif args.autocomplete:
+        do_autocomplete(args)
+    elif args.source:
+        do_source(args)
+    else:
+        do_query(args)
+
+
+if __name__ == "__main__":
+    main()
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/kconfig/utils.py
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/kconfig/utils.py
@@ -0,0 +1,20 @@
+# -*- mode: python -*-
+# Misc helpers for Kconfig and annotations
+# Copyright © 2023 Canonical Ltd.
+
+import sys
+
+
+def autodetect_annotations():
+    try:
+        with open("debian/debian.env", "rt", encoding="utf-8") as fd:
+            return fd.read().rstrip().split("=")[1] + "/config/annotations"
+    except (FileNotFoundError, IndexError):
+        return None
+
+
+def arg_fail(parser, message, show_usage=True):
+    print(message)
+    if show_usage:
+        parser.print_usage()
+    sys.exit(1)
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/kconfig/version.py
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/kconfig/version.py
@@ -0,0 +1,10 @@
+# -*- mode: python -*-
+# version of annotations module
+# Copyright © 2022 Canonical Ltd.
+
+VERSION = "0.1"
+
+ANNOTATIONS_FORMAT_VERSION = 5
+
+if __name__ == "__main__":
+    print(VERSION)
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/kernelconfig
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/kernelconfig
@@ -0,0 +1,177 @@
+#!/bin/bash -u
+#
+# Manage kernel config annotations
+#
+# Supported environment variales:
+#   conc_level  : Concurrency level for upstream make (-jX)
+#   skip_checks : Skip config checks if set to 'true'
+#   gcc         : Default gcc to use (mandatory)
+#
+
+function cleanup()
+{
+	rm -rf build "${TMP_DIR}"
+}
+
+# We have to be in the top level Ubuntu kernel source directory
+if ! [ -e debian/debian.env ] ; then
+	echo "ERROR: This is not an Ubuntu kernel source directory" >&2
+	exit 1
+fi
+
+if [ -z "${gcc:-}" ] ; then
+	gcc=gcc
+fi
+
+if [ ${#} -ne 1 ] ; then
+	echo "Usage: $0 updateconfigs|defaultconfigs|genconfigs|editconfigs"
+	exit 2
+fi
+
+mode=${1}
+
+case "${mode}" in
+	updateconfigs)  target="syncconfig" ;;
+	defaultconfigs) target="olddefconfig" ;;
+	genconfigs)     target="oldconfig" ;;
+	editconfigs)    ;;  # Target is set later based on user input
+	*) echo "ERROR: Invalid mode: ${1}" >&2
+	   exit 1 ;;
+esac
+
+. debian/debian.env
+
+annotations_file=${DEBIAN}/config/annotations
+warning_partial=()
+
+TMP_DIR=$(mktemp -d)
+trap cleanup EXIT
+
+# Use annotations to generate configs
+FLAVOURS=$(sed -ne 's/^# FLAVOUR: //p' "${annotations_file}")
+
+for arch_flavour in ${FLAVOURS} ; do
+	arch=${arch_flavour%%-*}
+	flavour=${arch_flavour#*-}
+	tmp_conf_file=${TMP_DIR}/${arch}-config.flavour.${flavour}
+
+	# Map debian archs to kernel archs
+	case "${arch}" in
+		amd64)   kern_arch="x86_64" ;;
+		arm64)   kern_arch="arm64" ;;
+		armhf)   kern_arch="arm" ;;
+		ppc64el) kern_arch="powerpc" ;;
+		riscv64) kern_arch="riscv" ;;
+		s390x)   kern_arch="s390" ;;
+		*)       echo "WARNING: Unsupported architecture: ${arch}"
+		         warning_partial+=("${arch}")
+		         continue ;;
+	esac
+
+	# Determine cross toolchain to use for Kconfig compiler tests
+	cross_compile="$(dpkg-architecture -qDEB_HOST_GNU_TYPE -a"${arch}" 2>/dev/null)-"
+
+	# Arch-specific compiler, if any
+	arch_gcc=$(cat <<EOF | make -s -f - all
+include ${DEBIAN}/rules.d/${arch}.mk
+all:
+	@echo \$(if \$(gcc),\$(gcc),${gcc})
+EOF
+			)
+	gcc_path=$(which "${cross_compile}${arch_gcc}" || true)
+	if [ -z "${gcc_path}" ] ; then
+		echo "WARNING: ${cross_compile}${arch_gcc} not installed"
+		warning_partial+=("${arch}")
+		continue
+	fi
+
+	if [ "${mode}" = "editconfigs" ] ; then
+		while true ; do
+			echo -n "Do you want to edit configs for ${arch}-${flavour}? [Y/n] "
+			read -r choice
+			case "${choice,,}" in
+				y|"") target="menuconfig" ; break ;;
+				n)    target="syncconfig" ; break ;;
+			esac
+		done
+	fi
+
+	rm -rf build
+	mkdir build
+
+	# Generate .config from annotations
+	python3 debian/scripts/misc/annotations -f "${annotations_file}" \
+			--arch "${arch}" --flavour "${flavour}" --export > build/.config
+
+	# Environment variables for 'make *config'
+	env=(ARCH="${kern_arch}"
+		 DEB_ARCH="${arch}"
+		 CROSS_COMPILE="${cross_compile}"
+		 CC="${gcc_path}")
+
+	# Concurrency level
+	if [ -n "${conc_level:-}" ] ; then
+		env+=("${conc_level}")
+	fi
+
+	# Call config target
+	echo
+	echo "* Run ${target} on ${arch}/${flavour} ..."
+	${kmake} O=build "${env[@]}" "${target}"
+
+	# Move config for further processing
+	mv build/.config "${tmp_conf_file}"
+done
+
+rc=0
+
+if [ "${skip_checks:-}" = "true" ] ; then
+	echo
+	echo "Skipping config-check (skip_checks=${skip_checks}) ..."
+else
+	echo
+	echo "Running config-check for all configurations ..."
+	fail=0
+	for arch_flavour in ${FLAVOURS} ; do
+		arch=${arch_flavour%%-*}
+		flavour=${arch_flavour#*-}
+		tmp_conf_file=${TMP_DIR}/${arch}-config.flavour.${flavour}
+
+		echo
+		echo "* Run config-check for ${arch}-${flavour} ..."
+		python3 debian/scripts/misc/annotations -f "${annotations_file}" \
+				--arch "${arch}" --flavour "${flavour}" --check "${tmp_conf_file}" || \
+			fail=$((fail + 1))
+	done
+
+	if [ ${fail} -gt 0 ] ; then
+		rc=1
+		echo "ERROR: ${fail} config-check failures detected" >&2
+	fi
+fi
+
+if [ ${#warning_partial[@]} -gt 0 ] ; then
+	rc=1
+	echo "ERROR: Config operation not applied to all architectures (skipped ${warning_partial[*]})" >&2
+fi
+
+# Recreate the annotations file
+if [ "${mode}" = "genconfigs" ] ; then
+	rm -rf CONFIGS
+	mv "${TMP_DIR}" CONFIGS
+else
+	echo
+	echo "Importing all configurations ..."
+	echo
+	for arch_flavour in ${FLAVOURS} ; do
+		arch=${arch_flavour%%-*}
+		flavour=${arch_flavour#*-}
+		tmp_conf_file=${TMP_DIR}/${arch}-config.flavour.${flavour}
+
+		echo "* Import configs for ${arch}-${flavour} ..."
+		python3 debian/scripts/misc/annotations -f "${annotations_file}" \
+				--arch "${arch}" --flavour "${flavour}" --import "${tmp_conf_file}"
+	done
+fi
+
+exit "${rc}"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/migrate-annotations
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/migrate-annotations
@@ -0,0 +1,35 @@
+#!/bin/bash
+
+. debian/debian.env
+
+# We have to be in the top level kernel source directory
+if [ ! -f MAINTAINERS ] || [ ! -f Makefile ]; then
+	echo "This does not appear to be the kernel source directory." 1>&2
+	exit 1
+fi
+
+. ${DEBIAN}/etc/kernelconfig
+
+ARCH=$(echo $archs | tr " " "\n" | sort -u)
+FLAVOUR=$(for arch in ${ARCH}; do
+	flavours=$(sed -ne 's/^flavours\s*=\s*\(.*\)$/\1/p' ${DEBIAN}/rules.d/${arch}.mk)
+	for flavour in ${flavours}; do
+		echo ${arch}-${flavour}
+	done
+done | tr " " "\n" | sort -u)
+
+while read line; do
+	(echo $line | grep -q '^#') || break
+done
+
+cat << EOF
+# Menu: HEADER
+# FORMAT: 4
+# ARCH: $(echo ${ARCH})
+# FLAVOUR: $(echo ${FLAVOUR})
+
+EOF
+
+while read line; do
+	echo ${line}
+done
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/old-kernelconfig
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/old-kernelconfig
@@ -0,0 +1,207 @@
+#!/bin/bash
+
+. debian/debian.env
+
+# Script to merge all configs and run 'make syncconfig' on it to wade out bad juju.
+# Then split the configs into distro-commmon and flavour-specific parts
+
+# We have to be in the top level kernel source directory
+if [ ! -f MAINTAINERS ] || [ ! -f Makefile ]; then
+	echo "This does not appear to be the kernel source directory." 1>&2
+	exit 1
+fi
+
+mode=${1:?"Usage: $0 (oldconfig|editconfig) [do_enforce_all]"}
+do_enforce_all=${2:-0}
+yes=0
+case "$mode" in
+    update*configs)  mode='syncconfig' ;;
+    default*configs) mode='oldconfig'; yes=1 ;;
+    edit*configs)    ;; # All is good
+    gen*configs)     mode='genconfigs' ;; # All is good
+    dump*configs)    mode='config'; yes=1 ;;
+    *) echo "$0 called with invalid mode" 1>&2
+       exit 1 ;;
+esac
+kerneldir="`pwd`"
+confdir="$kerneldir/${DEBIAN}/config"
+variant="$2"
+
+. $DEBIAN/etc/kernelconfig
+
+bindir="`pwd`/${DROOT}/scripts/misc"
+common_conf="$confdir/config.common.$family"
+tmpdir=`mktemp -d`
+mkdir "$tmpdir/CONFIGS"
+
+if [ "$mode" = "genconfigs" ]; then
+	keep=1
+	mode="oldconfig"
+	test -d CONFIGS || mkdir CONFIGS
+fi
+
+warning_partial=
+
+for arch in $archs; do
+	rm -rf build
+	mkdir build
+
+	# Map debian archs to kernel archs
+	case "$arch" in
+		ppc64|ppc64el)	kernarch="powerpc"	;;
+		amd64)		kernarch="x86_64"	;;
+		lpia)		kernarch="x86" 		;;
+		sparc)		kernarch="sparc64"	;;
+		armel|armhf)	kernarch="arm"		;;
+		s390x)		kernarch="s390"		;;
+		riscv64)	kernarch="riscv"	;;
+		*)		kernarch="$arch"	;;
+	esac
+
+	# Determine cross toolchain to use for Kconfig compiler tests
+	cross_compile=""
+	deb_build_arch=$(dpkg-architecture -qDEB_BUILD_ARCH -a$arch 2>/dev/null)
+	deb_host_arch=$(dpkg-architecture -qDEB_HOST_ARCH -a$arch 2>/dev/null)
+	[ $deb_build_arch != $deb_host_arch ] && cross_compile="$(dpkg-architecture -qDEB_HOST_GNU_TYPE -a$arch 2>/dev/null)-"
+
+	# Environment variables for 'make *config'. We omit CROSS_COMPILE
+	# for i386 since it is no longer supported after 19.04, however
+	# we maintain the configs for hwe.
+	modify_config=true
+	env="ARCH=$kernarch DEB_ARCH=$arch"
+	compiler_path=$(which "${cross_compile}gcc" || true)
+	if [ "$compiler_path" != '' ]; then
+		env="$env CROSS_COMPILE=$cross_compile"
+	else
+		echo "WARNING: ${cross_compile}gcc not installed"
+		modify_config=
+		warning_partial="$warning_partial $arch"
+	fi
+
+	archconfdir=$confdir/$arch
+	flavourconfigs=$(cd $archconfdir && ls config.flavour.*)
+
+	# Merge configs
+	# We merge config.common.ubuntu + config.common.<arch> +
+	# config.flavour.<flavour>
+
+	for config in $flavourconfigs; do
+		fullconf="$tmpdir/$arch-$config-full"
+		case $config in
+		*)
+			: >"$fullconf"
+			if [ -f $common_conf ]; then
+				cat $common_conf >> "$fullconf"
+			fi
+			if [ -f $archconfdir/config.common.$arch ]; then
+				cat $archconfdir/config.common.$arch >> "$fullconf"
+			fi
+			cat "$archconfdir/$config" >>"$fullconf"
+			if [ -f $confdir/OVERRIDES ]; then
+				cat $confdir/OVERRIDES >> "$fullconf"
+			fi
+			;;
+		esac
+	done
+
+	for config in $flavourconfigs; do
+		if [ -f $archconfdir/$config ]; then
+			fullconf="$tmpdir/$arch-$config-full"
+			cat "$fullconf" > build/.config
+			# Call oldconfig or menuconfig
+			if [ "$modify_config" ]; then
+				case "$mode" in
+				    editconfigs)
+					# Interactively edit config parameters
+					while : ; do
+						echo -n "Do you want to edit config: $arch/$config? [Y/n] "
+						read choice
+						case "$choice" in
+						y* | Y* | "" )
+							make O=`pwd`/build $env menuconfig
+							break ;;
+						n* | N* )
+							# 'syncconfig' prevents
+							# errors for '-' options set
+							# in common config fragments
+							make O=`pwd`/build $env syncconfig
+							break ;;
+						*)
+							echo "Entry not valid"
+						esac
+					done
+					;;
+				    *)
+					echo "* Run $mode (yes=$yes) on $arch/$config ..."
+					if [ "$yes" -eq 1 ]; then
+						yes "" | make O=`pwd`/build $env "$mode"
+					else
+						make O=`pwd`/build $env "$mode"
+					fi ;;
+				esac
+			fi
+			cat build/.config > $archconfdir/$config
+			[ "$modify_config" ] && cat build/.config >"$tmpdir/CONFIGS/$arch-$config"
+			if [ "$keep" = "1" ]; then
+				cat build/.config > CONFIGS/$arch-$config
+			fi
+		else
+			echo "!! Config not found $archconfdir/$config..."
+		fi
+	done
+
+	echo "Running splitconfig.pl for $arch"
+	echo
+
+	# Can we make this more robust by avoiding $tmpdir completely?
+	# This approach was used for now because I didn't want to change
+	# splitconfig.pl
+	(cd $archconfdir; $bindir/splitconfig.pl config.flavour.*; mv config.common \
+	 config.common.$arch; cp config.common.$arch $tmpdir)
+done
+
+rm -f $common_conf
+
+# Now run splitconfig.pl on all the config.common.<arch> copied to
+# $tmpdir
+(cd $tmpdir; $bindir/splitconfig.pl *)
+(
+	cd $confdir;
+	rm -f *-full
+	grep -v 'is UNMERGABLE' <$tmpdir/config.common >$common_conf
+	for arch in $archs; do
+		grep -v 'is UNMERGABLE' <$tmpdir/config.common.$arch \
+			>$arch/config.common.$arch
+	done
+)
+
+echo ""
+echo "Running config-check for all configurations ..."
+echo ""
+fail=0
+for arch in $archs; do
+	archconfdir=$confdir/$arch
+	flavourconfigs=$(cd $archconfdir && ls config.flavour.*)
+	for config in $flavourconfigs; do
+		flavour="${config##*.}"
+		if [ -f $archconfdir/$config ]; then
+			fullconf="$tmpdir/CONFIGS/$arch-$config"
+			[ ! -f "$fullconf" ] && continue
+			"$bindir/../config-check" "$fullconf" "$arch" "$flavour" "$confdir" "0" "$do_enforce_all" || let "fail=$fail+1"
+		fi
+	done
+done
+
+if [ "$fail" != 0 ]; then
+	echo ""
+	echo "*** ERROR: $fail config-check failures detected"
+	echo ""
+fi
+
+rm -rf build
+
+if [ "$warning_partial" ]; then
+	echo ""
+	echo "WARNING: configuration operation applied only to a subset of architectures (skipped$warning_partial)" 1>&2
+	echo ""
+fi
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/retag
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/retag
@@ -0,0 +1,34 @@
+#!/usr/bin/perl -w
+
+open(TAGS, "git tag -l |") or die "Could not get list of tags";
+@tags = <TAGS>;
+close(TAGS);
+
+open(LOGS, "git log --pretty=short |") or die "ERROR: Calling git log";
+my $commit = "";
+
+while (<LOGS>) {
+	my $origtag;
+
+	if (m|^commit (.*)$|) {
+		$commit = $1;
+		next;
+	}
+
+	m|\s*UBUNTU: (Ubuntu-2\.6\..*)| or next;
+
+	$tag = $1;
+
+	($origtag) = grep(/^$tag.orig$/, @tags);
+
+	if (!defined($origtag)) {
+		print "I: Adding original tag for $tag\n";
+		system("git tag -m $tag $tag.orig $tag");
+	}
+
+	print "I: Tagging $tag => $commit\n";
+
+	system("git tag -f -m $tag $tag $commit");
+}
+
+close(LOGS);
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/splitconfig.pl
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/splitconfig.pl
@@ -0,0 +1,107 @@
+#!/usr/bin/perl -w
+
+%allconfigs = ();
+%common = ();
+
+print "Reading config's ...\n";
+
+for $config (@ARGV) {
+	# Only config.*
+	next if $config !~ /^config\..*/;
+	# Nothing that is disabled, or remnant
+	next if $config =~ /.*\.(default|disabled|stub)$/;
+
+	%{$allconfigs{$config}} = ();
+
+	print "  processing $config ... ";
+
+	open(CONFIG, "< $config");
+
+	while (<CONFIG>) {
+		# Skip comments
+		/^#*\s*CONFIG_(\w+)[\s=](.*)$/ or next;
+
+		${$allconfigs{$config}}{$1} = $2;
+
+		$common{$1} = $2;
+	}
+
+	close(CONFIG);
+
+	print "done.\n";
+}
+
+print "\n";
+
+print "Merging lists ... \n";
+
+# %options - pointer to flavour config inside the allconfigs array
+for $config (keys(%allconfigs)) {
+	my %options = %{$allconfigs{$config}};
+
+	print "   processing $config ... ";
+
+	for $key (keys(%common)) {
+		next if not defined $common{$key};
+
+		# If we don't have the common option, then it isn't
+		# common. If we do have that option, it must have the same
+		# value.  EXCEPT where this file does not have a value at all
+		# which may safely be merged with any other value; the value
+		# will be elided during recombination of the parts.
+		if (!defined($options{$key})) {
+			# Its ok really ... let it merge
+		} elsif (not defined($options{$key})) {
+			undef $common{$key};
+		} elsif ($common{$key} ne $options{$key}) {
+			undef $common{$key};
+		}
+	}
+
+	print "done.\n";
+}
+
+print "\n";
+
+print "Creating common config ... ";
+
+open(COMMON, "> config.common");
+print COMMON "#\n# Common config options automatically generated by splitconfig.pl\n#\n";
+
+for $key (sort(keys(%common))) {
+	if (not defined $common{$key}) {
+		print COMMON "# CONFIG_$key is UNMERGABLE\n";
+	} elsif ($common{$key} eq "is not set") {
+		print COMMON "# CONFIG_$key is not set\n";
+	} else {
+		print COMMON "CONFIG_$key=$common{$key}\n";
+	}
+}
+close(COMMON);
+
+print "done.\n\n";
+
+print "Creating stub configs ...\n";
+
+for $config (keys(%allconfigs)) {
+	my %options = %{$allconfigs{$config}};
+
+	print "  processing $config ... ";
+
+	open(STUB, "> $config");
+	print STUB "#\n# Config options for $config automatically generated by splitconfig.pl\n#\n";
+
+	for $key (sort(keys(%options))) {
+		next if defined $common{$key};
+
+		if ($options{$key} =~ /^is /) {
+			print STUB "# CONFIG_$key $options{$key}\n";
+		} else {
+			print STUB "CONFIG_$key=$options{$key}\n";
+		}
+	}
+
+	close(STUB);
+
+	print "done.\n";
+}
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/tristate.sh
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/tristate.sh
@@ -0,0 +1,26 @@
+#!/bin/bash
+
+#
+# Find config variables that might be able to transition from =y to =m
+#
+# Example: debian/scripts/misc/tristate.sh debian.master/config/config.common.ubuntu
+#
+
+KC=Kconfig.tmp
+rm -f ${KC}
+find .|grep Kconfig | while read f
+do
+	cat $f >> ${KC}
+done
+
+grep =y $1 | sed -e 's/CONFIG_//' -e 's/=y//' | while read c
+do
+	cat <<EOF > tristate.awk
+BEGIN { tristate=0; }
+/^config ${c}\$/ { tristate=1; next; }
+/tristate/ { if (tristate == 1) printf("CONFIG_%s=m\n","${c}"); next; }
+{ if (tristate == 1) exit; }
+EOF
+
+	gawk -f tristate.awk ${KC}
+done
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/misc/update-aufs.sh
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/misc/update-aufs.sh
@@ -0,0 +1,50 @@
+#!/bin/bash
+
+AUFS=aufs4-standalone
+
+#
+# Before you run this be sure you've removed or reverted the 'UBUNTU: SAUCE: AUFS" patch.
+#
+#
+# Make sure the current working directory is at the top of the
+# linux tree.
+#
+if ! grep PATCHLEVEL Makefile
+then
+	echo "You must run this script from the top of the linux tree"
+	exit 1
+fi
+
+clean=0
+if [ "$#" = 1 ]; then
+	AUFS="$1"
+else
+	clean=1
+	rm -rf ${AUFS}
+	git clone https://github.com/sfjro/aufs5-standalone.git ${AUFS}
+	(cd ${AUFS}; git checkout -b aufs5.x-rcN remotes/origin/aufs5.x-rcN)
+fi
+
+cp ${AUFS}/include/uapi/linux/aufs_type.h include/uapi/linux
+rsync -av ${AUFS}/fs/ fs/
+rsync -av ${AUFS}/Documentation/ Documentation/
+
+PATCHES="${PATCHES} aufs5-kbuild.patch"
+PATCHES="${PATCHES} aufs5-base.patch"
+PATCHES="${PATCHES} aufs5-mmap.patch"
+PATCHES="${PATCHES} aufs5-standalone.patch"
+PATCHES="${PATCHES} aufs5-loopback.patch"
+#PATCHES="${PATCHES} vfs-ino.patch"
+#PATCHES="${PATCHES} tmpfs-idr.patch"
+
+for i in ${PATCHES}
+do
+	patch -p1 < ${AUFS}/$i
+done
+
+[ "$clean" = 1 ] && rm -rf ${AUFS}
+git add mm/prfile.c
+git add -u
+find . -name "*.orig" | xargs rm
+find . |grep aufs | xargs git add
+git commit -s -m"UBUNTU: SAUCE: AUFS"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/module-inclusion
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/module-inclusion
@@ -0,0 +1,104 @@
+#!/bin/bash
+
+#
+# Build a new directory of modules based on an inclusion list.
+# The includsion list format must be a bash regular expression.
+#
+# usage: $0 ROOT INCLUSION_LIST
+# example: $0 \
+#       debian/build/build-virtual-ALL debian/build/build-virtual \
+#	debian.master/control.d/virtual.inclusion-list \
+#	virtual.depmap
+master=0
+if [ "$1" = "--master" ]; then
+	master=1
+	shift
+fi
+
+ROOT=$1
+NROOT=$2
+ILIST=$3
+DEPMAP=$4
+
+tmp="/tmp/module-inclusion.$$"
+
+#
+# Prep a destination directory.
+#
+mkdir -p ${NROOT}
+
+{
+	# Copy over the framework into the master package.
+	if  [ "$master" -eq 1 ]; then
+		(cd ${ROOT}; find . ! -name "*.ko" -type f)
+	fi
+
+	# Copy over modules by name or pattern.
+	while read -r i
+	do
+		#
+		# 'find' blurts a warning if it cannot find any ko files.
+		#
+		case "$i" in
+		\!*)
+			(cd ${ROOT}; ${i#!} || true)
+			;;
+		*\**)
+			(cd ${ROOT}; eval find "${i}" -name "*.ko" || true)
+			;;
+		*)
+			echo "$i"
+			;;
+		esac
+	done <"${ILIST}"
+} >"$tmp"
+
+# Copy over the listed modules.
+while read i
+do
+	# If this is already moved over, all is good.
+	if [ -f "${NROOT}/$i" ]; then
+		:
+
+	# If present in the source, moved it over.
+	elif [ -f "${ROOT}/$i" ]; then
+		mkdir -p "${NROOT}/`dirname $i`"
+		mv "${ROOT}/$i" "${NROOT}/$i"
+
+	# Otherwise, it is missing.
+	else
+		echo "Warning: Could not find ${ROOT}/$i" 1>&2
+	fi
+done <"$tmp"
+
+# Copy over any dependancies, note if those are missing
+# we know they are in a pre-requisite package as they must
+# have existed at depmap generation time, and can only have
+# moved into a package.
+let n=0 || true
+while [ -s "$tmp" ]
+do
+	let n="$n+1" || true
+	[ "$n" = "20" ] && break || true
+
+	echo "NOTE: pass $n: dependency scan" 1>&2
+
+	while read i
+	do
+		grep "^$i " "$DEPMAP" | \
+		while read m d
+		do
+			if [ -f "${ROOT}/$d" ]; then
+				echo "NOTE: pass $n: ${i} pulls in ${d}" 1>&2
+				echo "$d"
+				mkdir -p "${NROOT}/`dirname $d`"
+				mv "${ROOT}/$d" "${NROOT}/$d"
+			fi
+		done
+	done <"$tmp" >"$tmp.new"
+	mv -f "$tmp.new" "$tmp"
+done
+
+rm -f "$tmp"
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/module-signature-check
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/module-signature-check
@@ -0,0 +1,76 @@
+#!/bin/bash -eu
+
+flavor="${1}"
+mods_dir="${2}"
+mods_extra_dir="${3}"
+
+echo "II: Checking signature of staging modules for ${flavor}..."
+
+root=$(dirname "$(realpath -e "${0}")")/../..
+. "${root}"/debian/debian.env
+
+# Collect the signature-inclusion files
+sig_incs=()
+for d in debian "${DEBIAN}" ; do
+	if [ -f "${root}"/"${d}"/signature-inclusion ] ; then
+		sig_incs+=("${root}"/"${d}"/signature-inclusion)
+	fi
+done
+
+if [ "${#sig_incs[@]}" -gt 0 ] ; then
+	echo "II: Use signature inclusion file(s):"
+	printf "    %s\n" "${sig_incs[@]}"
+	sig_all=0
+else
+	echo "WW: Signature inclusion file(s) missing"
+	echo "II: All modules must be signed"
+	sig_all=1
+fi
+
+if ! [ -d "${mods_dir}" ] ; then
+	echo "EE: Modules directory missing:"
+	echo "    ${mods_dir}"
+	exit 1
+fi
+
+echo "II: Checking modules directory:"
+echo "    ${mods_dir}"
+mods_dirs=("${mods_dir}")
+
+if [ -d "${mods_extra_dir}" ] ; then
+	echo "    ${mods_extra_dir}"
+	mods_dirs+=("${mods_extra_dir}")
+fi
+
+pass=0
+fail=0
+while IFS= read -r mod ; do
+	is=0
+	if /sbin/modinfo "${mod}" | grep -q "^signature:" ; then
+		# Module is signed
+		is=1
+	fi
+
+	must=0
+	if [ ${sig_all} -eq 1 ] || grep -qFx "${mod##*/}" "${sig_incs[@]}" ; then
+		# Module must be signed
+		must=1
+	fi
+
+	case "${is}${must}" in
+		00) echo "    PASS (unsigned) : ${mod##*/}" ; pass=$((pass + 1)) ;;
+		01) echo "    FAIL (unsigned) : ${mod##*/}" ; fail=$((fail + 1)) ;;
+		10) echo "    FAIL (signed)   : ${mod##*/}" ; fail=$((fail + 1)) ;;
+		11) echo "    PASS (signed)   : ${mod##*/}" ; pass=$((pass + 1)) ;;
+	esac
+done < <(find "${mods_dirs[@]}" -path '*/drivers/staging/*.ko' | sort)
+
+echo "II: Checked $((pass + fail)) modules : ${pass} PASS, ${fail} FAIL"
+
+if [ ${fail} -eq 0 ] ; then
+	echo "II: Done"
+	exit 0
+else
+	echo "EE: Modules signature failures"
+	exit 1
+fi
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/retpoline-extract
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/retpoline-extract
@@ -0,0 +1,23 @@
+#!/bin/bash
+
+cd "$1" || exit 1
+
+# Find all valid retpoline information, collate the detected and
+# safe information together.  Join the result to find the detected
+# but non-safe elements.  These are our concern.
+ur_detected=$(mktemp --tmpdir "retpoline-check-XXXXXX.ur-detected")
+ur_safe=$(mktemp --tmpdir "retpoline-check-XXXXXX.ur-safe")
+
+find "." -path './drivers/firmware/efi/libstub' -prune -o \
+	 -path './arch/x86/boot' -prune -o \
+	 -path './arch/x86/purgatory' -prune -o \
+	 -name \*.ur-detected -print0 | xargs -0 cat | \
+	sed -e "s@^$1@@" -e "s@ $2/@ @" -e "s@^/@@" | \
+	sort -k 1b,1 >"$ur_detected"
+find "." -name \*.ur-safe -print0 | xargs -0 cat | \
+	sed -e "s@^$1@@" -e "s@^/@@" | \
+	sort -k 1b,1 >"$ur_safe"
+
+join -v 1 -j 1 "$ur_detected" "$ur_safe" | sed -s 's/[^ ]*  *//'
+
+rm -f "$ur_detected" "$ur_safe"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/retpoline-extract-one
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/retpoline-extract-one
@@ -0,0 +1,270 @@
+#!/bin/bash
+
+exec </dev/null
+
+object="$1"
+src="$2"
+bit16="$3"
+
+SECTION=".discard.retpoline_safe"
+
+# Form an associative lookup for the symbol numbers in the ELF symbol table.
+# Uses 8 character 0 expanded hexadecimal key for ease of consumption.
+__symbolmap_init()
+{
+	readelf -W --syms "$1" |
+		awk '($4 == "SECTION" && $1 ~ /^[0-9]*:/) { printf("%08x %08x\n", int($1), int($7)); }' | \
+	while read symbol_num section_num
+	do
+		echo "symbolmap_$symbol_num='$section_num'"
+	done
+}
+symbolmap_init()
+{
+	eval $(__symbolmap_init "$1")
+}
+symbolmap()
+{
+	eval RET="\$symbolmap_$1"
+	if [ "$RET" = '' ]; then
+		echo "symbolmap: $1: invalid section" 1>&2
+		exit 1
+	fi
+}
+
+# Form an associative lookup for the section numbers in the ELF symbol table.
+# Uses 8 character 0 expanded hexadecimal key for ease of consumption.
+__sectionmap_init()
+{
+	readelf -W --headers "$1" | \
+		awk '
+						{ sub("\\[", ""); sub("\\]", ""); }
+                        ($1 ~ /^[0-9][0-9]*/)   { printf("%08x %s %s %s\n", int($1), $2, $3, $4); }
+		' | \
+	{
+		while read section_num section_name section_type section_vma
+		do
+			echo "sectionmap_$section_num='$section_name'"
+			echo "sectionvma_$section_num='$section_vma'"
+			case "$section_type" in
+			REL|RELA) section_relocation="$section_type" ;;
+			esac
+		done
+		echo "section_relocation='$section_relocation'"
+	}
+}
+sectionmap_init()
+{
+	eval $(__sectionmap_init "$1")
+}
+sectionmap()
+{
+	eval RET="\$sectionmap_$1"
+	if [ "$RET" = '' ]; then
+		echo "sectionmap: $1: invalid section" 1>&2
+		exit 1
+	fi
+}
+sectionvma()
+{
+	eval RET="\$sectionvma_$1"
+	if [ "$RET" = '' ]; then
+		echo "sectionvma: $1: invalid section" 1>&2
+		exit 1
+	fi
+}
+
+# Read and parse the hex-dump output.
+hex="[0-9a-f]"
+hex_8="$hex$hex$hex$hex$hex$hex$hex$hex"
+hexspc="[0-9a-f ]"
+hexspc_8="$hexspc$hexspc$hexspc$hexspc$hexspc$hexspc$hexspc$hexspc"
+
+raw32()
+{
+	readelf --hex-dump "$2" "$1" 2>/dev/null |
+	sed \
+		-e '/^Hex/d' -e '/^$/d' -e '/^ *NOTE/d' \
+		-e 's/  *[^ ][^ ]*  *\('"$hex_8"'\) \('"$hexspc_8"'\) \('"$hexspc_8"'\) \('"$hexspc_8"'\) .*/\1 \2 \3 \4 /' \
+		-e 's/\('"$hex$hex"'\)\('"$hex$hex"'\)\('"$hex$hex"'\)\('"$hex$hex"'\) /\4\3\2\1 /g' \
+		-e 's/ $//g' -e 's/ /\n/g'
+}
+#-e 's/\([^ ][^ ][^ ][^ ][^ ][^ ][^ ][^ ]\) \([^ ][^ ][^ ][^ ][^ ][^ ][^ ][^ ]\) /\2\1 /g' \
+
+rela()
+{
+	#file="$(basename "$1")"
+	file="$1"
+
+	# Read relocation information for a 64bit binary.  Each relocation entry
+	# is 3 long longs so we collect 6 quads here.  Note that the dump is in
+	# listed in increasing byte order not withstanding the quad split.
+	#
+	# The record says to take the value of <symbol> add <symbol offset> and
+	# shove that into <write offset> in the segment of the <symbol>.
+	#
+	# Format:
+	#  <write offset>	64 bits
+	#  <symbol number>	32 bits
+	#  <relocation type>	32 bits
+	#  <symbol offset>	64 bits
+	raw32 "$1" ".rela$SECTION" | \
+	{
+		a1=''; a2=''; a3=''; a4=''; a5=''
+		while read a6
+		do
+			[ "$a1" = '' ] && { a1="$a6"; continue; }
+			[ "$a2" = '' ] && { a2="$a6"; continue; }
+			[ "$a3" = '' ] && { a3="$a6"; continue; }
+			[ "$a4" = '' ] && { a4="$a6"; continue; }
+			[ "$a5" = '' ] && { a5="$a6"; continue; }
+
+			#echo ">$a1< >$a2< >$a3< >$a4< >$a5< >$a6<" 1>&2
+			#echo "type<$a3> symbol<$a4> offset<$a2$a1> addr<$a6a5>" 1>&2
+
+			symbolmap "$a4"; section_num="$RET"
+			#echo "section_num<$section_num>" 1>&2
+
+			sectionmap "$section_num"; section="$RET"
+			sectionvma "$section_num"; vma="$RET"
+			#echo "section<$section> vma<$vma>" 1>&2
+
+			# Adjust the segment addressing by the segment offset.
+			printf -v addr "%u" "0x$a6$a5"
+			printf -v vma "%u" "0x$vma"
+			let offset="$addr + $vma"
+			printf -v offset "%x" "$offset"
+
+			echo "$file-$section-$offset"
+
+			a1=''; a2=''; a3=''; a4=''; a5=''
+		done
+	} | sed -e 's/-00*\([0-9a-f]\)/-\1/'
+}
+
+# Form an associative lookup for the raw contents for an ELF section.
+# Uses 8 character 0 expanded hexadecimal key for ease of consumption.
+contentmap_init()
+{
+	raw32 "$1" "$2" >"$tmp"
+	let offset=0
+	while read value
+	do
+		printf -v offset_hex "%08x" $offset
+		eval contentmap_$offset_hex=\'$value\'
+
+		let offset="$offset + 4"
+	done <"$tmp"
+	rm -f "$tmp"
+}
+contentmap()
+{
+	eval RET="\$contentmap_$1"
+	if [ "$RET" = '' ]; then
+		echo "contentmap: $1: invalid offset" 1>&2
+		exit 1
+	fi
+}
+
+rel()
+{
+	# Load up the current contents of the $SECTION segment
+	# as the offsets (see below) are recorded there and we will need
+	# those to calculate the actuall address.
+	contentmap_init "$1" "$SECTION"
+
+	#file="$(basename "$1")"
+	file="$1"
+
+	# Read relocation information for a 32bit binary.  Each relocation entry
+	# is 3 longs so we collect 3 quads here.  Note that the dump is in
+	# listed in increasing byte order not withstanding the quad split.
+	#
+	# The record says to take the value of <symbol> and add that to the
+	# existing contents of <write offset> in the segment of the <symbol>.
+	#
+	# Format:
+	#  <write offset>	32 bits
+	#  <symbol number>	24 bits
+	#  <relocation type>	 8 bits
+	raw32 "$1" ".rel$SECTION" | \
+	{
+		a1=''
+		while read a2
+		do
+			[ "$a1" = '' ] && { a1="$a2"; continue; }
+
+			#echo ">$a1< >$a2<"
+			contentmap "$a1"; offset="$RET"
+			symbolmap "00${a2%??}"; section_num="$RET"
+
+			sectionmap "$section_num"; section="$RET"
+			sectionvma "$section_num"; vma="$RET"
+			#echo ">$a1< >$a2< >$offset< >$section<"
+
+			echo "$file-$section-$offset"
+
+			a1=''
+		done
+	} | sed -e 's/-00*\([0-9a-f]\)/-\1/'
+}
+
+tmp=$(mktemp --tmpdir "retpoline-extract-XXXXXX")
+
+disassemble()
+{
+	local object="$1"
+	local src="$2"
+	local options="$3"
+	local selector="$4"
+
+	objdump $options --disassemble --no-show-raw-insn "$object" | \
+	awk -F' ' '
+		BEGIN				{ file="'"$object"'"; src="'"$src"'"; }
+		/Disassembly of section/        { segment=$4; sub(":", "", segment); }
+		/^[0-9a-f][0-9a-f]* <.*>:/      { tag=$0; sub(".*<", "", tag); sub(">.*", "", tag); }
+		$0 ~ /(call|jmp)q?  *\*0x[0-9a-f]*\(%rip\)/ {
+			next
+		}
+		$0 ~ /(call|jmp)q?  *\*.*%/ {
+			sub(":", "", $1);
+			if ('"$selector"') {
+				offset=$1
+				$1=tag
+				print(file "-" segment "-" offset " " src " " segment " " $0);
+			}
+		}
+	'
+}
+
+# Accumulate potentially vunerable indirect call/jmp sequences.  We do this
+# by examining the raw disassembly for affected forms, recording the location
+# of each.
+case "$bit16" in
+'')	disassemble "$object" "$src" '' 'segment != ".init.text"' ;;
+*)	disassemble "$object" "$src" '--disassembler-options=i8086' 'segment != ".init.text" && segment != ".text32" && segment != ".text64"'
+	disassemble "$object" "$src" '--disassembler-options=i386' 'segment == ".text32"'
+	disassemble "$object" "$src" '--disassembler-options=x86-64' 'segment == ".text64"'
+	;;
+esac | sort -k 1b,1 >"$object.ur-detected"
+[ ! -s "$object.ur-detected" ] && rm -f "$object.ur-detected"
+
+# Load up the symbol table and section mappings.
+symbolmap_init "$object"
+sectionmap_init "$object"
+
+# Accumulate annotated safe indirect call/jmp sequences.  We do this by examining
+# the $SECTION sections (and their associated relocation information),
+# each entry represents the address of an instruction which has been marked
+# as ok.
+case "$section_relocation" in
+REL)	rel "$object" ;;
+RELA)	rela "$object" ;;
+esac | sort -k 1b,1 >"$object.ur-safe"
+[ ! -s "$object.ur-safe" ] && rm -f "$object.ur-safe"
+
+# We will perform the below join on the summarised and sorted fragments
+# formed above.  This is performed in retpoline-check.
+#join -v 1 -j 1 "$tmp.extracted" "$tmp.safe" | sed -s 's/[^ ]*  *//'
+
+rm -f "$tmp"
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/sign-module
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/sign-module
@@ -0,0 +1,40 @@
+#!/bin/bash -eu
+#
+# Staging drivers must not be signed if they are not listed in a
+# signature-inclusion file to prevent loading of 'unsafe' drivers in a
+# Secure Boot environment.
+#
+# Exit with status 0 if the provided module needs to be signed, 1 otherwise
+#
+
+mod=${1}
+
+# Sign the module if not a staging driver
+if [ "${mod/\/drivers\/staging\//}" = "${mod}" ] ; then
+	exit 0
+fi
+
+root=$(dirname "$(realpath -e "${0}")")/../..
+. "${root}"/debian/debian.env
+
+# Collect the signature-inclusion files
+sig_incls=()
+for d in debian "${DEBIAN}" ; do
+	if [ -f "${root}"/"${d}"/signature-inclusion ] ; then
+		sig_incls+=("${root}"/"${d}"/signature-inclusion)
+	fi
+done
+
+# Sign the module if no signature-inclusion files
+if [ ${#sig_incls[@]} -eq 0 ] ; then
+	exit 0
+fi
+
+# Sign the module if listed in signature-inclusion files
+if grep -qFx "${mod##*/}" "${sig_incls[@]}" ; then
+	exit 0
+fi
+
+# Don't sign the module
+echo "UBUNTU: Not signing ${1}"
+exit 1
--- linux-xilinx-zynqmp-5.15.0.orig/debian/scripts/sub-flavour
+++ linux-xilinx-zynqmp-5.15.0/debian/scripts/sub-flavour
@@ -0,0 +1,69 @@
+#!/bin/bash
+
+. debian/debian.env
+
+echo "SUB_PROCESS $FROM => $TO"
+
+export from_pkg="linux-image-$ABI_RELEASE-$FROM"
+export to_pkg="linux-image-$ABI_RELEASE-$TO"
+
+from_moddir="debian/$from_pkg/lib/modules/$ABI_RELEASE-$FROM"
+to_moddir="debian/$to_pkg/lib/modules/$ABI_RELEASE-$FROM"
+
+install -d "debian/$to_pkg/boot"
+install -m644 debian/$from_pkg/boot/config-$ABI_RELEASE-$FROM \
+	debian/$to_pkg/boot/
+install -m600 debian/$from_pkg/boot/{vmlinuz,System.map}-$ABI_RELEASE-$FROM \
+	debian/$to_pkg/boot/
+
+#
+# Print some warnings if there are files in the sub-flavours list
+# that do not actually exist.
+#
+cat ${DEBIAN}/sub-flavours/$TO.list | while read line
+do
+(
+	cd debian/$from_pkg/lib/modules/$ABI_RELEASE-$FROM/kernel;
+	#
+	# If its a wildcard, then check that there are files that match.
+	#
+	if echo "$line" | grep '\*' > /dev/null
+	then
+		if [ `eval find "$line" -name '*.ko' 2>/dev/null|wc -l` -lt 1 ]
+		then
+			echo SUB_INST Warning - No files in $line
+		fi
+	#
+	# Else it should be a single file reference.
+	#
+	elif [ ! -f "$line" ]
+	then
+		echo SUB_INST Warning - could not find "$line"
+	fi
+)
+done
+
+cat ${DEBIAN}/sub-flavours/$TO.list | while read line; do
+	(
+	cd debian/$from_pkg/lib/modules/$ABI_RELEASE-$FROM/kernel;
+	if echo "$line" | grep '\*' > /dev/null
+	then
+		eval find "$line" -name '*.ko' 2>/dev/null || true
+	elif [ -f "$line" ]
+	then
+		echo "$line"
+	fi
+	);
+done | while read mod; do
+	echo "SUB_INST checking: $mod"
+	fromdir="/lib/modules/$ABI_RELEASE-$FROM/"
+	egrep "^($fromdir)?kernel/$mod:" \
+		$from_moddir/modules.dep | sed -e "s|^$fromdir||" -e 's/://' -e 's/ /\n/g' | \
+	while read m; do
+		m="${fromdir}$m"
+		test -f debian/$to_pkg/$m && continue
+		echo "SUB_INST installing: $m"
+		install -D -m644 debian/$from_pkg/$m \
+			debian/$to_pkg/$m
+	done
+done
--- linux-xilinx-zynqmp-5.15.0.orig/debian/signature-inclusion
+++ linux-xilinx-zynqmp-5.15.0/debian/signature-inclusion
@@ -0,0 +1,12 @@
+#
+# This file lists the staging drivers that are safe for signing
+# and loading in a secure boot environment with signed module enforcement.
+#
+r8188eu.ko
+r8192e_pci.ko
+r8192u_usb.ko
+r8712u.ko
+rtllib_crypt_ccmp.ko
+rtllib_crypt_tkip.ko
+rtllib_crypt_wep.ko
+rtllib.ko
--- linux-xilinx-zynqmp-5.15.0.orig/debian/snapcraft.mk
+++ linux-xilinx-zynqmp-5.15.0/debian/snapcraft.mk
@@ -0,0 +1,15 @@
+ifeq ($(ARCH),)
+  arch := $(shell uname -m | sed -e s/i.86/i386/ -e s/x86_64/amd64/ \
+            -e s/arm.*/armhf/ -e s/s390/s390x/ -e s/ppc.*/powerpc/ \
+            -e s/aarch64.*/arm64/ )
+else ifeq ($(ARCH),arm)
+  arch := armhf
+else
+  arch := $(ARCH)
+endif
+config:
+	if [ -e debian/config/config.common.ubuntu ]; then \
+	    cat debian.$(branch)/config/config.common.ubuntu debian.$(branch)/config/$(arch)/config.common.$(arch) debian.$(branch)/config/$(arch)/config.flavour.$(flavour) >.config; \
+	else \
+	    python3 debian/scripts/misc/annotations --export --arch $(arch) --flavour $(flavour) >.config; \
+	fi
--- linux-xilinx-zynqmp-5.15.0.orig/debian/source/format
+++ linux-xilinx-zynqmp-5.15.0/debian/source/format
@@ -0,0 +1 @@
+1.0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/source/options
+++ linux-xilinx-zynqmp-5.15.0/debian/source/options
@@ -0,0 +1,8 @@
+# Ignore vbox symlinks, we will regenerate these at clean (LP:1426113)
+## autoreconstruct -- begin
+# Ignore any symlinks created since the orig which are rebuilt by reconstruct.
+## autoreconstruct -- end
+
+# force "dpkg-source -I -i" behavior
+diff-ignore
+tar-ignore
--- linux-xilinx-zynqmp-5.15.0.orig/debian/stamps/keep-dir
+++ linux-xilinx-zynqmp-5.15.0/debian/stamps/keep-dir
@@ -0,0 +1 @@
+Place holder
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/extra.postinst.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/extra.postinst.in
@@ -0,0 +1,20 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+image_path=/boot/@image-stem@-$version
+
+if [ "$1" != configure ]; then
+    exit 0
+fi
+
+depmod -a -F /boot/System.map-$version $version || true
+if [ -d /etc/kernel/postinst.d ]; then
+    cat - >/usr/lib/linux/triggers/$version <<EOF
+DEB_MAINT_PARAMS="$*" run-parts --report --exit-on-error --arg=$version \
+	    --arg="$image_path" /etc/kernel/postinst.d
+EOF
+    dpkg-trigger --no-await linux-update-$version
+fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/extra.postrm.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/extra.postrm.in
@@ -0,0 +1,31 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+image_path=/boot/@image-stem@-$version
+
+if [ "$1" != remove ]; then
+    exit 0
+fi
+
+depmod -a -F /boot/System.map-$version $version 2>/dev/null || true
+#
+# We should be rebuilding the initramfs here on removal to pare down the
+# initramfs if it contains any of the objects we just removed.  But people
+# commonly remove kernels in order to free space in /boot, and rebuilding the
+# initramfs now risks ENOSPC when we are trying to make space.  The files we
+# leave lying about could be confusing, but we trade that against safety on
+# removal.
+#
+#if [ -d /etc/kernel/postinst.d ]; then
+#    # We want to behave as if linux-image (without us) was installed, therefore
+#    # we do not want the postinst support to know we are being removed, claim
+#    # this is an installation event.
+#    cat - >/usr/lib/linux/triggers/$version <<EOF
+#DEB_MAINT_PARAMS="configure" run-parts --report --exit-on-error --arg=$version \
+#	--arg="$image_path" /etc/kernel/postinst.d
+#EOF
+#    dpkg-trigger --no-await linux-update-$version
+#fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/headers.postinst.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/headers.postinst.in
@@ -0,0 +1,15 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+
+if [ "$1" != configure ]; then
+    exit 0
+fi
+
+if [ -d /etc/kernel/header_postinst.d ]; then
+    DEB_MAINT_PARAMS="$*" run-parts --report --exit-on-error --arg=$version \
+		/etc/kernel/header_postinst.d
+fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/image.postinst.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/image.postinst.in
@@ -0,0 +1,62 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+image_path=/boot/@image-stem@-$version
+
+#
+# When we install linux-image we have to run kernel postinst.d support to
+# generate the initramfs, create links etc.  Should it have an associated
+# linux-image-extra package and we install that we also need to run kernel
+# postinst.d, to regenerate the initramfs.  If we are installing both at the
+# same time, we necessarily trigger kernel postinst.d twice. As this includes
+# rebuilding the initramfs and reconfiguring the boot loader this is very time
+# consuming.
+#
+# Similarly for removal when we remove the linux-image-extra package we need to
+# run kernel postinst.d handling in order to pare down the initramfs to
+# linux-image contents only.  When we remove the linux-image need to remove the
+# now redundant initramfs.  If we are removing both at the same time, then
+# we will rebuilt the initramfs and then immediatly remove it.
+#
+# Switches to using a trigger against the linux-image package for all
+# postinst.d and postrm.d handling.  On installation postinst.d gets triggered
+# twice once by linux-image and once by linux-image-extra.  As triggers are
+# non-cumulative we will only run this processing once.  When removing both
+# packages we will trigger postinst.d from linux-image-extra and then in
+# linux-image postrm.d we effectivly ignore the pending trigger and simply run
+# the postrm.d.  This prevents us from rebuilding the initramfs.
+#
+if [ "$1" = triggered ]; then
+    trigger=/usr/lib/linux/triggers/$version
+    if [ -f "$trigger" ]; then
+	sh "$trigger"
+	rm -f "$trigger"
+    fi
+    exit 0
+fi
+
+if [ "$1" != configure ]; then
+    exit 0
+fi
+
+depmod $version
+
+if [ -f /lib/modules/$version/.fresh-install ]; then
+    change=install
+else
+    change=upgrade
+fi
+linux-update-symlinks $change $version $image_path
+rm -f /lib/modules/$version/.fresh-install
+
+if [ -d /etc/kernel/postinst.d ]; then
+    mkdir -p /usr/lib/linux/triggers
+    cat - >/usr/lib/linux/triggers/$version <<EOF
+DEB_MAINT_PARAMS="$*" run-parts --report --exit-on-error --arg=$version \
+      --arg=$image_path /etc/kernel/postinst.d
+EOF
+    dpkg-trigger --no-await linux-update-$version
+fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/image.postrm.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/image.postrm.in
@@ -0,0 +1,40 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+image_path=/boot/@image-stem@-$version
+
+rm -f /lib/modules/$version/.fresh-install
+
+if [ "$1" != upgrade ] && command -v linux-update-symlinks >/dev/null; then
+    linux-update-symlinks remove $version $image_path
+fi
+
+if [ -d /etc/kernel/postrm.d ]; then
+    # We cannot trigger ourselves as at the end of this we will no longer
+    # exist and can no longer respond to the trigger.  The trigger would
+    # then become lost.  Therefore we clear any pending trigger and apply
+    # postrm directly.
+    if [ -f /usr/lib/linux/triggers/$version ]; then
+	echo "$0 ... removing pending trigger"
+	rm -f /usr/lib/linux/triggers/$version
+    fi
+    DEB_MAINT_PARAMS="$*" run-parts --report --exit-on-error --arg=$version \
+	      --arg=$image_path /etc/kernel/postrm.d
+fi
+
+if [ "$1" = purge ]; then
+    for extra_file in modules.dep modules.isapnpmap modules.pcimap \
+                      modules.usbmap modules.parportmap \
+                      modules.generic_string modules.ieee1394map \
+                      modules.ieee1394map modules.pnpbiosmap \
+                      modules.alias modules.ccwmap modules.inputmap \
+                      modules.symbols modules.ofmap \
+                      modules.seriomap modules.\*.bin \
+		      modules.softdep modules.devname; do
+	eval rm -f /lib/modules/$version/$extra_file
+    done
+    rmdir /lib/modules/$version || true
+fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/image.preinst.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/image.preinst.in
@@ -0,0 +1,22 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+image_path=/boot/@image-stem@-$version
+
+if [ "$1" = abort-upgrade ]; then
+    exit 0
+fi
+
+if [ "$1" = install ]; then
+    # Create a flag file for postinst
+    mkdir -p /lib/modules/$version
+    touch /lib/modules/$version/.fresh-install
+fi
+
+if [ -d /etc/kernel/preinst.d ]; then
+    DEB_MAINT_PARAMS="$*" run-parts --report --exit-on-error --arg=$version \
+	      --arg=$image_path /etc/kernel/preinst.d
+fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/templates/image.prerm.in
+++ linux-xilinx-zynqmp-5.15.0/debian/templates/image.prerm.in
@@ -0,0 +1,18 @@
+#!/bin/sh
+set -e
+
+version=@abiname@@localversion@
+image_path=/boot/@image-stem@-$version
+
+if [ "$1" != remove ]; then
+    exit 0
+fi
+
+linux-check-removal $version
+
+if [ -d /etc/kernel/prerm.d ]; then
+    DEB_MAINT_PARAMS="$*" run-parts --report --exit-on-error --arg=$version \
+	      --arg=$image_path /etc/kernel/prerm.d
+fi
+
+exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/debian/tests-build/README
+++ linux-xilinx-zynqmp-5.15.0/debian/tests-build/README
@@ -0,0 +1,21 @@
+Scripts placed in this directory get called one at a time by run-parts(8).
+The scripts are expected to perform some sort of sanity checks on the
+finished build. Scripts will be called once for each flavour.
+
+Some environment variables are exported to make life a little easier:
+
+DPKG_ARCH     : The dpkg architecture (e.g. "amd64")
+KERN_ARCH     : The kernel architecture (e.g. "x86_64")
+FLAVOUR       : The specific flavour for this run (e.g. "generic")
+VERSION       : The full version of this build (e.g. 2.6.22-1)
+REVISION      : The exact revision of this build (e.g. 1.3)
+PREV_REVISION : The revision prior to this one
+ABI_NUM       : The specific ABI number for this build (e.g. 2)
+PREV_ABI_NUM  : The previous ABI number. Can be the same as ABI_NUM.
+BUILD_DIR     : The directory where this build took place
+INSTALL_DIR   : The directory where the package is prepared
+SOURCE_DIR    : Where the main kernel source is
+
+Scripts are expected to have a zero exit status when no problems occur,
+and non-zero when an error occurs that should stop the build. Scripts
+should print whatever info they deem needed to deduce the problem.
--- linux-xilinx-zynqmp-5.15.0.orig/debian/tests-build/check-aliases
+++ linux-xilinx-zynqmp-5.15.0/debian/tests-build/check-aliases
@@ -0,0 +1,26 @@
+#!/usr/bin/perl -w
+
+my %map;
+
+print "Checking for dupe aliases in $ENV{'FLAVOUR'}...\n";
+
+$aliases =
+  "$ENV{'INSTALL_DIR'}/lib/modules/$ENV{'VERSION'}-$ENV{'FLAVOUR'}/modules.alias";
+
+exit 0 unless (-e $aliases);
+
+open(ALIASES, "< $aliases") or die "Could not open $aliases";
+
+while (<ALIASES>) {
+	chomp;
+	my ($junk, $alias, $module) = split;
+
+	if (defined($map{$alias})) {
+		printf("%s %20s / %-20s : %s \n", ("$map{$alias}" eq "$module")
+			? "INT" : "   ", $map{$alias}, $module, $alias);
+	} else {
+		$map{$alias} = $module;
+	}
+}
+
+exit(0);
--- linux-xilinx-zynqmp-5.15.0.orig/debian/tests/control
+++ linux-xilinx-zynqmp-5.15.0/debian/tests/control
@@ -0,0 +1,7 @@
+Tests: rebuild
+Depends: @builddeps@, fakeroot
+Restrictions: allow-stderr, skippable
+
+Tests: ubuntu-regression-suite
+Depends: build-essential, gcc-multilib [amd64 armhf i386], gdb, git, python2 | python, bzr
+Restrictions: allow-stderr, isolation-machine, breaks-testbed, skippable
--- linux-xilinx-zynqmp-5.15.0.orig/debian/tests/rebuild
+++ linux-xilinx-zynqmp-5.15.0/debian/tests/rebuild
@@ -0,0 +1,20 @@
+#!/bin/sh
+
+# If we are triggering for just linux or linux-meta we know we have
+# just built the kernel and there is no point in repeating that
+# build, it just wastes time.  (LP: #1498862)
+build_needed=0
+for trigger in ${ADT_TEST_TRIGGERS:-force}
+do
+	case "$trigger" in
+	linux/*|linux-lts-*/*|linux-meta*/*|linux-oem*/*|fakeroot/*|gdb/*|git/*|bzr/*|gcc-multilib/*)	;;
+	*)						build_needed=1 ;;
+	esac
+done
+if [ "$build_needed" -eq 0 ]; then
+	echo "rebuild: short circuiting build for '${ADT_TEST_TRIGGERS}'"
+	exit 77
+fi
+
+set -e
+dpkg-buildpackage -rfakeroot -us -uc -b -Pautopkgtest
--- linux-xilinx-zynqmp-5.15.0.orig/debian/tests/ubuntu-regression-suite
+++ linux-xilinx-zynqmp-5.15.0/debian/tests/ubuntu-regression-suite
@@ -0,0 +1,45 @@
+#!/bin/sh
+set -e
+
+# Only run regression-suite on kernels we can boot in canonistack
+source=`dpkg-parsechangelog -SSource`
+case $source in
+    linux|linux-unstable|linux-hwe*|linux-lowlatency*|linux-kvm|linux-oem)
+	;;
+    *)
+	echo "ubuntu-regression-suite is pointless, if one cannot boot the kernel"
+	exit 77
+	;;
+esac
+
+# Only run regression-suite if we were requested to
+have_meta=0
+for trigger in ${ADT_TEST_TRIGGERS}
+do
+    case "$trigger" in
+	linux-meta/*|linux-meta-*/*)
+	    have_meta=1
+	    ;;
+    esac
+done
+if [ -n "$ADT_TEST_TRIGGERS" ] && [ "$have_meta" -eq 0 ]; then
+    echo "ubuntu-regression-suite is not requested, as there is no linux-meta trigger"
+    exit 77
+fi
+
+sver=`dpkg-parsechangelog -SVersion`
+read x rver x </proc/version_signature
+
+flavour=${rver#*-*-}
+rver=${rver%-$flavour}
+
+echo "Source Package Version: $sver"
+echo "Running Kernel Version: $rver"
+
+if [ "$sver" != "$rver" ]; then
+    echo "ERROR: running version does not match source package" 1>&2
+    exit 1
+fi
+
+git clone --depth=1 git://git.launchpad.net/~canonical-kernel-team/+git/kernel-testing
+kernel-testing/run-dep8-tests
--- linux-xilinx-zynqmp-5.15.0.orig/debian/tools/generic
+++ linux-xilinx-zynqmp-5.15.0/debian/tools/generic
@@ -0,0 +1,60 @@
+#!/bin/bash
+full_version=`uname -r`
+
+# First check for a fully qualified version.
+this="/usr/lib/linux-tools/$full_version/`basename $0`"
+if [ -f "$this" ]; then
+	exec "$this" "$@"
+fi
+
+# Removing flavour from version i.e. generic or server.
+flavour_abi=${full_version#*-}
+flavour=${flavour_abi#*-}
+version=${full_version%-$flavour}
+this="$0_$version"
+if [ -f "$this" ]; then
+	exec "$this" "$@"
+fi
+
+# Before saucy kernels we had no flavour linkage.
+if dpkg --compare-versions "$version" lt "3.11.0"; then
+	flavour=''
+else
+	flavour="-$flavour"
+fi
+# Hint at the cloud tools if they exist (trusty and later)
+if dpkg --compare-versions "$version" ge "3.13.0"; then
+	cld=""
+else
+	cld=":"
+fi
+# Work out if this is an LTS backport or not.
+codename=`lsb_release -cs`
+case "$codename" in
+precise)	base='3.2.0-9999' ;;
+trusty)		base='3.13.0-9999' ;;
+*)		base='' ;;
+esac
+std=""
+lts=":"
+if [ "$base" != "" ]; then
+	if dpkg --compare-versions "$version" gt "$base"; then
+		std=":"
+		lts=""
+	fi
+fi
+
+# Give them a hint as to what to install.
+		echo "WARNING: `basename $0` not found for kernel $version" >&2
+		echo "" >&2
+		echo "  You may need to install the following packages for this specific kernel:" >&2
+		echo "    linux-tools-$version$flavour" >&2
+$cld		echo "    linux-cloud-tools-$version$flavour" >&2
+		echo "" >&2
+		echo "  You may also want to install one of the following packages to keep up to date:" >&2
+$std		echo "    linux-tools$flavour" >&2
+$std $cld	echo "    linux-cloud-tools$flavour" >&2
+$lts		echo "    linux-tools$flavour-lts-<series>" >&2
+$lts $cld	echo "    linux-cloud-tools$flavour-lts-<series>" >&2
+
+exit 2
--- linux-xilinx-zynqmp-5.15.0.orig/debian/v4l2loopback-modules.ignore
+++ linux-xilinx-zynqmp-5.15.0/debian/v4l2loopback-modules.ignore
@@ -0,0 +1 @@
+v4l2loopback
--- linux-xilinx-zynqmp-5.15.0.orig/debian/wireguard-modules.ignore
+++ linux-xilinx-zynqmp-5.15.0/debian/wireguard-modules.ignore
@@ -0,0 +1 @@
+wireguard
--- linux-xilinx-zynqmp-5.15.0.orig/debian/zfs-modules.ignore
+++ linux-xilinx-zynqmp-5.15.0/debian/zfs-modules.ignore
@@ -0,0 +1,11 @@
+icp
+spl
+splat
+zavl
+zcommon
+zfs
+zlua
+znvpair
+zpios
+zunicode
+zzstd
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/Makefile
@@ -41,8 +41,7 @@
 # SOC specific infrastructure drivers.
 obj-y				+= soc/
 
-obj-$(CONFIG_VIRTIO)		+= virtio/
-obj-$(CONFIG_VIRTIO_PCI_LIB)	+= virtio/
+obj-y				+= virtio/
 obj-$(CONFIG_VDPA)		+= vdpa/
 obj-$(CONFIG_XEN)		+= xen/
 
@@ -60,14 +59,9 @@
 # iommu/ comes before gpu as gpu are using iommu controllers
 obj-y				+= iommu/
 
-# gpu/ comes after char for AGP vs DRM startup and after iommu
-obj-y				+= gpu/
 
 obj-$(CONFIG_CONNECTOR)		+= connector/
 
-# i810fb and intelfb depend on char/agp/
-obj-$(CONFIG_FB_I810)           += video/fbdev/i810/
-obj-$(CONFIG_FB_INTEL)          += video/fbdev/intelfb/
 
 obj-$(CONFIG_PARPORT)		+= parport/
 obj-y				+= base/ block/ misc/ mfd/ nfc/
@@ -80,6 +74,12 @@
 obj-y				+= scsi/
 obj-y				+= nvme/
 obj-$(CONFIG_ATA)		+= ata/
+
+# gpu/ comes after char for AGP vs DRM startup and after iommu
+obj-y				+= gpu/
+# i810fb and intelfb depend on char/agp/
+obj-$(CONFIG_FB_I810)           += video/fbdev/i810/
+obj-$(CONFIG_FB_INTEL)          += video/fbdev/intelfb/
 obj-$(CONFIG_TARGET_CORE)	+= target/
 obj-$(CONFIG_MTD)		+= mtd/
 obj-$(CONFIG_SPI)		+= spi/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/accessibility/speakup/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/accessibility/speakup/main.c
@@ -573,7 +573,7 @@
 	}
 	attr_ch = get_char(vc, (u_short *)tmp_pos, &spk_attr);
 	buf[cnt++] = attr_ch;
-	while (tmpx < vc->vc_cols - 1) {
+	while (tmpx < vc->vc_cols - 1 && cnt < ARRAY_SIZE(buf) - 1) {
 		tmp_pos += 2;
 		tmpx++;
 		ch = get_char(vc, (u_short *)tmp_pos, &temp);
@@ -1778,7 +1778,7 @@
 {
 	unsigned long flags;
 
-	if (!speakup_console[vc->vc_num] || spk_parked)
+	if (!speakup_console[vc->vc_num] || spk_parked || !synth)
 		return;
 	if (!spin_trylock_irqsave(&speakup_info.spinlock, flags))
 		/* Speakup output, discard */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/accessibility/speakup/speakup_dectlk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/accessibility/speakup/speakup_dectlk.c
@@ -44,6 +44,7 @@
 	{ CAPS_START, .u.s = {"[:dv ap 160] " } },
 	{ CAPS_STOP, .u.s = {"[:dv ap 100 ] " } },
 	{ RATE, .u.n = {"[:ra %d] ", 180, 75, 650, 0, 0, NULL } },
+	{ PITCH, .u.n = {"[:dv ap %d] ", 122, 50, 350, 0, 0, NULL } },
 	{ INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
 	{ VOL, .u.n = {"[:dv g5 %d] ", 86, 60, 86, 0, 0, NULL } },
 	{ PUNCT, .u.n = {"[:pu %c] ", 0, 0, 2, 0, 0, "nsa" } },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/accessibility/speakup/spk_ttyio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/accessibility/speakup/spk_ttyio.c
@@ -88,7 +88,7 @@
 	}
 
 	if (!ldisc_data->buf_free)
-		/* ttyio_in will tty_schedule_flip */
+		/* ttyio_in will tty_flip_buffer_push */
 		return 0;
 
 	/* Make sure the consumer has read buf before we have seen
@@ -312,7 +312,7 @@
 	mb();
 	ldisc_data->buf_free = true;
 	/* Let TTY push more characters */
-	tty_schedule_flip(tty->port);
+	tty_flip_buffer_push(tty->port);
 
 	return rv;
 }
@@ -354,6 +354,9 @@
 {
 	struct tty_struct *tty = in_synth->dev;
 
+	if (tty == NULL)
+		return;
+
 	tty_lock(tty);
 
 	if (tty->ops->close)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/accessibility/speakup/synth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/accessibility/speakup/synth.c
@@ -208,8 +208,10 @@
 	wake_up_process(speakup_task);
 }
 
-void synth_write(const char *buf, size_t count)
+void synth_write(const char *_buf, size_t count)
 {
+	const unsigned char *buf = (const unsigned char *) _buf;
+
 	while (count--)
 		synth_buffer_add(*buf++);
 	synth_start();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/Makefile
@@ -80,6 +80,9 @@
 obj-$(CONFIG_ACPI_BUTTON)	+= button.o
 obj-$(CONFIG_ACPI_TINY_POWER_BUTTON)	+= tiny-power-button.o
 obj-$(CONFIG_ACPI_FAN)		+= fan.o
+fan-objs			:= fan_core.o
+fan-objs			+= fan_attr.o
+
 obj-$(CONFIG_ACPI_VIDEO)	+= video.o
 obj-$(CONFIG_ACPI_TAD)		+= acpi_tad.o
 obj-$(CONFIG_ACPI_PCI_SLOT)	+= pci_slot.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/ac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/ac.c
@@ -61,6 +61,7 @@
 
 static int ac_sleep_before_get_state_ms;
 static int ac_check_pmic = 1;
+static int ac_only;
 
 static struct acpi_driver acpi_ac_driver = {
 	.name = "ac",
@@ -93,6 +94,11 @@
 	if (!ac)
 		return -EINVAL;
 
+	if (ac_only) {
+		ac->state = 1;
+		return 0;
+	}
+
 	status = acpi_evaluate_integer(ac->device->handle, "_PSR", NULL,
 				       &ac->state);
 	if (ACPI_FAILURE(status)) {
@@ -200,6 +206,12 @@
 	return 0;
 }
 
+static int __init ac_only_quirk(const struct dmi_system_id *d)
+{
+	ac_only = 1;
+	return 0;
+}
+
 /* Please keep this list alphabetically sorted */
 static const struct dmi_system_id ac_dmi_table[]  __initconst = {
 	{
@@ -210,6 +222,13 @@
 		},
 	},
 	{
+		/* Kodlix GK45 returning incorrect state */
+		.callback = ac_only_quirk,
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "GK45"),
+		},
+	},
+	{
 		/* Lenovo Ideapad Miix 320, AXP288 PMIC, separate fuel-gauge */
 		.callback = ac_do_not_check_pmic_quirk,
 		.matches = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_extlog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_extlog.c
@@ -12,6 +12,7 @@
 #include <linux/ratelimit.h>
 #include <linux/edac.h>
 #include <linux/ras.h>
+#include <acpi/ghes.h>
 #include <asm/cpu.h>
 #include <asm/mce.h>
 
@@ -138,15 +139,20 @@
 	int	cpu = mce->extcpu;
 	struct acpi_hest_generic_status *estatus, *tmp;
 	struct acpi_hest_generic_data *gdata;
-	const guid_t *fru_id = &guid_null;
-	char *fru_text = "";
+	const guid_t *fru_id;
+	char *fru_text;
 	guid_t *sec_type;
 	static u32 err_seq;
 
 	estatus = extlog_elog_entry_check(cpu, bank);
-	if (estatus == NULL || (mce->kflags & MCE_HANDLED_CEC))
+	if (!estatus)
 		return NOTIFY_DONE;
 
+	if (mce->kflags & MCE_HANDLED_CEC) {
+		estatus->block_status = 0;
+		return NOTIFY_DONE;
+	}
+
 	memcpy(elog_buf, (void *)estatus, ELOG_ENTRY_LEN);
 	/* clear record status to enable BIOS to update it again */
 	estatus->block_status = 0;
@@ -160,17 +166,23 @@
 
 	/* log event via trace */
 	err_seq++;
-	gdata = (struct acpi_hest_generic_data *)(tmp + 1);
-	if (gdata->validation_bits & CPER_SEC_VALID_FRU_ID)
-		fru_id = (guid_t *)gdata->fru_id;
-	if (gdata->validation_bits & CPER_SEC_VALID_FRU_TEXT)
-		fru_text = gdata->fru_text;
-	sec_type = (guid_t *)gdata->section_type;
-	if (guid_equal(sec_type, &CPER_SEC_PLATFORM_MEM)) {
-		struct cper_sec_mem_err *mem = (void *)(gdata + 1);
-		if (gdata->error_data_length >= sizeof(*mem))
-			trace_extlog_mem_event(mem, err_seq, fru_id, fru_text,
-					       (u8)gdata->error_severity);
+	apei_estatus_for_each_section(tmp, gdata) {
+		if (gdata->validation_bits & CPER_SEC_VALID_FRU_ID)
+			fru_id = (guid_t *)gdata->fru_id;
+		else
+			fru_id = &guid_null;
+		if (gdata->validation_bits & CPER_SEC_VALID_FRU_TEXT)
+			fru_text = gdata->fru_text;
+		else
+			fru_text = "";
+		sec_type = (guid_t *)gdata->section_type;
+		if (guid_equal(sec_type, &CPER_SEC_PLATFORM_MEM)) {
+			struct cper_sec_mem_err *mem = (void *)(gdata + 1);
+
+			if (gdata->error_data_length >= sizeof(*mem))
+				trace_extlog_mem_event(mem, err_seq, fru_id, fru_text,
+						       (u8)gdata->error_severity);
+		}
 	}
 
 out:
@@ -296,9 +308,10 @@
 static void __exit extlog_exit(void)
 {
 	mce_unregister_decode_chain(&extlog_mce_dec);
-	((struct extlog_l1_head *)extlog_l1_addr)->flags &= ~FLAG_OS_OPTIN;
-	if (extlog_l1_addr)
+	if (extlog_l1_addr) {
+		((struct extlog_l1_head *)extlog_l1_addr)->flags &= ~FLAG_OS_OPTIN;
 		acpi_os_unmap_iomem(extlog_l1_addr, l1_size);
+	}
 	if (elog_addr)
 		acpi_os_unmap_iomem(elog_addr, elog_size);
 	release_mem_region(elog_base, elog_size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_fpdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_fpdt.c
@@ -143,6 +143,23 @@
 
 static struct kobject *fpdt_kobj;
 
+#if defined CONFIG_X86 && defined CONFIG_PHYS_ADDR_T_64BIT
+#include <linux/processor.h>
+static bool fpdt_address_valid(u64 address)
+{
+	/*
+	 * On some systems the table contains invalid addresses
+	 * with unsuppored high address bits set, check for this.
+	 */
+	return !(address >> boot_cpu_data.x86_phys_bits);
+}
+#else
+static bool fpdt_address_valid(u64 address)
+{
+	return true;
+}
+#endif
+
 static int fpdt_process_subtable(u64 address, u32 subtable_type)
 {
 	struct fpdt_subtable_header *subtable_header;
@@ -151,6 +168,11 @@
 	u32 length, offset;
 	int result;
 
+	if (!fpdt_address_valid(address)) {
+		pr_info(FW_BUG "invalid physical address: 0x%llx!\n", address);
+		return -EINVAL;
+	}
+
 	subtable_header = acpi_os_map_memory(address, sizeof(*subtable_header));
 	if (!subtable_header)
 		return -ENOMEM;
@@ -172,12 +194,19 @@
 		record_header = (void *)subtable_header + offset;
 		offset += record_header->length;
 
+		if (!record_header->length) {
+			pr_err(FW_BUG "Zero-length record found in FPTD.\n");
+			result = -EINVAL;
+			goto err;
+		}
+
 		switch (record_header->type) {
 		case RECORD_S3_RESUME:
 			if (subtable_type != SUBTABLE_S3PT) {
 				pr_err(FW_BUG "Invalid record %d for subtable %s\n",
 				     record_header->type, signature);
-				return -EINVAL;
+				result = -EINVAL;
+				goto err;
 			}
 			if (record_resume) {
 				pr_err("Duplicate resume performance record found.\n");
@@ -186,7 +215,7 @@
 			record_resume = (struct resume_performance_record *)record_header;
 			result = sysfs_create_group(fpdt_kobj, &resume_attr_group);
 			if (result)
-				return result;
+				goto err;
 			break;
 		case RECORD_S3_SUSPEND:
 			if (subtable_type != SUBTABLE_S3PT) {
@@ -201,13 +230,14 @@
 			record_suspend = (struct suspend_performance_record *)record_header;
 			result = sysfs_create_group(fpdt_kobj, &suspend_attr_group);
 			if (result)
-				return result;
+				goto err;
 			break;
 		case RECORD_BOOT:
 			if (subtable_type != SUBTABLE_FBPT) {
 				pr_err(FW_BUG "Invalid %d for subtable %s\n",
 				     record_header->type, signature);
-				return -EINVAL;
+				result = -EINVAL;
+				goto err;
 			}
 			if (record_boot) {
 				pr_err("Duplicate boot performance record found.\n");
@@ -216,7 +246,7 @@
 			record_boot = (struct boot_performance_record *)record_header;
 			result = sysfs_create_group(fpdt_kobj, &boot_attr_group);
 			if (result)
-				return result;
+				goto err;
 			break;
 
 		default:
@@ -225,6 +255,18 @@
 		}
 	}
 	return 0;
+
+err:
+	if (record_boot)
+		sysfs_remove_group(fpdt_kobj, &boot_attr_group);
+
+	if (record_suspend)
+		sysfs_remove_group(fpdt_kobj, &suspend_attr_group);
+
+	if (record_resume)
+		sysfs_remove_group(fpdt_kobj, &resume_attr_group);
+
+	return result;
 }
 
 static int __init acpi_init_fpdt(void)
@@ -233,6 +275,7 @@
 	struct acpi_table_header *header;
 	struct fpdt_subtable_entry *subtable;
 	u32 offset = sizeof(*header);
+	int result;
 
 	status = acpi_get_table(ACPI_SIG_FPDT, 0, &header);
 
@@ -241,8 +284,8 @@
 
 	fpdt_kobj = kobject_create_and_add("fpdt", acpi_kobj);
 	if (!fpdt_kobj) {
-		acpi_put_table(header);
-		return -ENOMEM;
+		result = -ENOMEM;
+		goto err_nomem;
 	}
 
 	while (offset < header->length) {
@@ -250,8 +293,10 @@
 		switch (subtable->type) {
 		case SUBTABLE_FBPT:
 		case SUBTABLE_S3PT:
-			fpdt_process_subtable(subtable->address,
+			result = fpdt_process_subtable(subtable->address,
 					      subtable->type);
+			if (result)
+				goto err_subtable;
 			break;
 		default:
 			/* Other types are reserved in ACPI 6.4 spec. */
@@ -260,6 +305,12 @@
 		offset += sizeof(*subtable);
 	}
 	return 0;
+err_subtable:
+	kobject_put(fpdt_kobj);
+
+err_nomem:
+	acpi_put_table(header);
+	return result;
 }
 
 fs_initcall(acpi_init_fpdt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_lpit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_lpit.c
@@ -98,7 +98,7 @@
 				 struct acpi_lpit_native *lpit_native)
 {
 	info->frequency = lpit_native->counter_frequency ?
-				lpit_native->counter_frequency : tsc_khz * 1000;
+				lpit_native->counter_frequency : mul_u32_u32(tsc_khz, 1000U);
 	if (!info->frequency)
 		info->frequency = 1;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_lpss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_lpss.c
@@ -403,6 +403,9 @@
 	if (!lpss_clk_dev)
 		lpt_register_clock_device();
 
+	if (IS_ERR(lpss_clk_dev))
+		return PTR_ERR(lpss_clk_dev);
+
 	clk_data = platform_get_drvdata(lpss_clk_dev);
 	if (!clk_data)
 		return -ENODEV;
@@ -436,8 +439,9 @@
 		if (!clk_name)
 			return -ENOMEM;
 		clk = clk_register_fractional_divider(NULL, clk_name, parent,
+						      0, prv_base, 1, 15, 16, 15,
 						      CLK_FRAC_DIVIDER_POWER_OF_TWO_PS,
-						      prv_base, 1, 15, 16, 15, 0, NULL);
+						      NULL);
 		parent = clk_name;
 
 		clk_name = kasprintf(GFP_KERNEL, "%s-update", devname);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_pad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_pad.c
@@ -129,8 +129,10 @@
 {
 	struct cpumask *pad_busy_cpus = to_cpumask(pad_busy_cpus_bits);
 
-	cpumask_clear_cpu(tsk_in_cpu[tsk_index], pad_busy_cpus);
-	tsk_in_cpu[tsk_index] = -1;
+	if (tsk_in_cpu[tsk_index] != -1) {
+		cpumask_clear_cpu(tsk_in_cpu[tsk_index], pad_busy_cpus);
+		tsk_in_cpu[tsk_index] = -1;
+	}
 }
 
 static unsigned int idle_pct = 5; /* percentage */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_processor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_processor.c
@@ -373,7 +373,7 @@
 
 	result = acpi_processor_get_info(device);
 	if (result) /* Processor is not physically present or unavailable */
-		return 0;
+		goto err_clear_driver_data;
 
 	BUG_ON(pr->id >= nr_cpu_ids);
 
@@ -388,7 +388,7 @@
 			"BIOS reported wrong ACPI id %d for the processor\n",
 			pr->id);
 		/* Give up, but do not abort the namespace scan. */
-		goto err;
+		goto err_clear_driver_data;
 	}
 	/*
 	 * processor_device_array is not cleared on errors to allow buggy BIOS
@@ -400,12 +400,12 @@
 	dev = get_cpu_device(pr->id);
 	if (!dev) {
 		result = -ENODEV;
-		goto err;
+		goto err_clear_per_cpu;
 	}
 
 	result = acpi_bind_one(dev, device);
 	if (result)
-		goto err;
+		goto err_clear_per_cpu;
 
 	pr->dev = dev;
 
@@ -416,10 +416,11 @@
 	dev_err(dev, "Processor driver could not be attached\n");
 	acpi_unbind_one(dev);
 
- err:
-	free_cpumask_var(pr->throttling.shared_cpu_map);
-	device->driver_data = NULL;
+ err_clear_per_cpu:
 	per_cpu(processors, pr->id) = NULL;
+ err_clear_driver_data:
+	device->driver_data = NULL;
+	free_cpumask_var(pr->throttling.shared_cpu_map);
  err_free_pr:
 	kfree(pr);
 	return result;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpi_video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpi_video.c
@@ -73,6 +73,7 @@
 static int only_lcd = -1;
 module_param(only_lcd, int, 0444);
 
+static bool may_report_brightness_keys;
 static int register_count;
 static DEFINE_MUTEX(register_count_mutex);
 static DEFINE_MUTEX(video_list_lock);
@@ -495,6 +496,22 @@
 		DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE R830"),
 		},
 	},
+	{
+	 .callback = video_disable_backlight_sysfs_if,
+	 .ident = "Toshiba Satellite Z830",
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE Z830"),
+		},
+	},
+	{
+	 .callback = video_disable_backlight_sysfs_if,
+	 .ident = "Toshiba Portege Z830",
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE Z830"),
+		},
+	},
 	/*
 	 * Some machine's _DOD IDs don't have bit 31(Device ID Scheme) set
 	 * but the IDs actually follow the Device ID Scheme.
@@ -549,6 +566,15 @@
 		DMI_MATCH(DMI_PRODUCT_NAME, "Vostro 3350"),
 		},
 	},
+	{
+	 .callback = video_set_report_key_events,
+	 .driver_data = (void *)((uintptr_t)REPORT_BRIGHTNESS_KEY_EVENTS),
+	 .ident = "COLORFUL X15 AT 23",
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "COLORFUL"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "X15 AT 23"),
+		},
+	},
 	/*
 	 * Some machines change the brightness themselves when a brightness
 	 * hotkey gets pressed, despite us telling them not to. In this case
@@ -1222,6 +1248,9 @@
 	acpi_video_device_bind(video, data);
 	acpi_video_device_find_cap(data);
 
+	if (data->cap._BCM && data->cap._BCL)
+		may_report_brightness_keys = true;
+
 	mutex_lock(&video->device_list_lock);
 	list_add_tail(&data->entry, &video->video_device_list);
 	mutex_unlock(&video->device_list_lock);
@@ -1689,6 +1718,9 @@
 		break;
 	}
 
+	if (keycode)
+		may_report_brightness_keys = true;
+
 	acpi_notifier_call_chain(device, event, 0);
 
 	if (keycode && (report_key_events & REPORT_BRIGHTNESS_KEY_EVENTS)) {
@@ -1770,12 +1802,12 @@
 		return;
 	count++;
 
-	acpi_get_parent(device->dev->handle, &acpi_parent);
-
-	pdev = acpi_get_pci_dev(acpi_parent);
-	if (pdev) {
-		parent = &pdev->dev;
-		pci_dev_put(pdev);
+	if (ACPI_SUCCESS(acpi_get_parent(device->dev->handle, &acpi_parent))) {
+		pdev = acpi_get_pci_dev(acpi_parent);
+		if (pdev) {
+			parent = &pdev->dev;
+			pci_dev_put(pdev);
+		}
 	}
 
 	memset(&props, 0, sizeof(struct backlight_properties));
@@ -2251,6 +2283,7 @@
 	if (register_count) {
 		acpi_bus_unregister_driver(&acpi_video_bus);
 		register_count = 0;
+		may_report_brightness_keys = false;
 	}
 	mutex_unlock(&register_count_mutex);
 }
@@ -2272,13 +2305,7 @@
 
 bool acpi_video_handles_brightness_key_presses(void)
 {
-	bool have_video_busses;
-
-	mutex_lock(&video_list_lock);
-	have_video_busses = !list_empty(&video_bus_head);
-	mutex_unlock(&video_list_lock);
-
-	return have_video_busses &&
+	return may_report_brightness_keys &&
 	       (report_key_events & REPORT_BRIGHTNESS_KEY_EVENTS);
 }
 EXPORT_SYMBOL(acpi_video_handles_brightness_key_presses);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/Makefile
@@ -3,8 +3,9 @@
 # Makefile for ACPICA Core interpreter
 #
 
-ccflags-y			:= -Os -D_LINUX -DBUILDING_ACPICA
+ccflags-y			:= -D_LINUX -DBUILDING_ACPICA
 ccflags-$(CONFIG_ACPI_DEBUG)	+= -DACPI_DEBUG_OUTPUT
+CFLAGS_tbfind.o 		+= $(call cc-disable-warning, stringop-truncation)
 
 # use acpi.o to put all files here into acpi.o modparam namespace
 obj-y	+= acpi.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/acglobal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/acglobal.h
@@ -226,6 +226,8 @@
     acpi_gbl_bit_register_info[ACPI_NUM_BITREG];
 ACPI_GLOBAL(u8, acpi_gbl_sleep_type_a);
 ACPI_GLOBAL(u8, acpi_gbl_sleep_type_b);
+ACPI_GLOBAL(u8, acpi_gbl_sleep_type_a_s0);
+ACPI_GLOBAL(u8, acpi_gbl_sleep_type_b_s0);
 
 /*****************************************************************************
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/achware.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/achware.h
@@ -101,8 +101,6 @@
 acpi_hw_get_gpe_status(struct acpi_gpe_event_info *gpe_event_info,
 		       acpi_event_status *event_status);
 
-acpi_status acpi_hw_disable_all_gpes(void);
-
 acpi_status acpi_hw_enable_all_runtime_gpes(void);
 
 acpi_status acpi_hw_enable_all_wakeup_gpes(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/dbconvert.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/dbconvert.c
@@ -174,6 +174,8 @@
 	elements =
 	    ACPI_ALLOCATE_ZEROED(DB_DEFAULT_PKG_ELEMENTS *
 				 sizeof(union acpi_object));
+	if (!elements)
+		return (AE_NO_MEMORY);
 
 	this = string;
 	for (i = 0; i < (DB_DEFAULT_PKG_ELEMENTS - 1); i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/dbnames.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/dbnames.c
@@ -550,8 +550,12 @@
 	ACPI_FREE(buffer.pointer);
 
 	buffer.length = ACPI_ALLOCATE_LOCAL_BUFFER;
-	acpi_evaluate_object(obj_handle, NULL, NULL, &buffer);
-
+	status = acpi_evaluate_object(obj_handle, NULL, NULL, &buffer);
+	if (ACPI_FAILURE(status)) {
+		acpi_os_printf("Could Not evaluate object %p\n",
+			       obj_handle);
+		return (AE_OK);
+	}
 	/*
 	 * Since this is a field unit, surround the output in braces
 	 */
@@ -652,6 +656,9 @@
 		object_info =
 		    ACPI_ALLOCATE_ZEROED(sizeof(struct acpi_object_info));
 
+		if (!object_info)
+			return (AE_NO_MEMORY);
+
 		/* Walk the namespace from the root */
 
 		(void)acpi_walk_namespace(ACPI_TYPE_ANY, ACPI_ROOT_OBJECT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/dsmethod.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/dsmethod.c
@@ -517,7 +517,7 @@
 	info = ACPI_ALLOCATE_ZEROED(sizeof(struct acpi_evaluate_info));
 	if (!info) {
 		status = AE_NO_MEMORY;
-		goto cleanup;
+		goto pop_walk_state;
 	}
 
 	info->parameters = &this_walk_state->operands[0];
@@ -529,7 +529,7 @@
 
 	ACPI_FREE(info);
 	if (ACPI_FAILURE(status)) {
-		goto cleanup;
+		goto pop_walk_state;
 	}
 
 	next_walk_state->method_nesting_depth =
@@ -575,6 +575,12 @@
 
 	return_ACPI_STATUS(status);
 
+pop_walk_state:
+
+	/* On error, pop the walk state to be deleted from thread */
+
+	acpi_ds_pop_walk_state(thread);
+
 cleanup:
 
 	/* On error, we must terminate the method properly */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/dswexec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/dswexec.c
@@ -395,11 +395,11 @@
 
 			/* Resolve all operands */
 
+			union acpi_operand_object **stack_ptr = NULL;
+			if (walk_state->num_operands > 0)
+				stack_ptr = ACPI_WALK_OPERANDS;
 			status = acpi_ex_resolve_operands(walk_state->opcode,
-							  &(walk_state->
-							    operands
-							    [walk_state->
-							     num_operands - 1]),
+							  stack_ptr,
 							  walk_state);
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/dswstate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/dswstate.c
@@ -576,9 +576,14 @@
 	ACPI_FUNCTION_TRACE(ds_init_aml_walk);
 
 	walk_state->parser_state.aml =
-	    walk_state->parser_state.aml_start = aml_start;
-	walk_state->parser_state.aml_end =
-	    walk_state->parser_state.pkg_end = aml_start + aml_length;
+	    walk_state->parser_state.aml_start =
+	    walk_state->parser_state.aml_end =
+	    walk_state->parser_state.pkg_end = aml_start;
+	/* Avoid undefined behavior: applying zero offset to null pointer */
+	if (aml_length != 0) {
+		walk_state->parser_state.aml_end += aml_length;
+		walk_state->parser_state.pkg_end += aml_length;
+	}
 
 	/* The next_op of the next_walk will be the beginning of the method */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/evxfregn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/evxfregn.c
@@ -201,8 +201,6 @@
 
 			/* Now we can delete the handler object */
 
-			acpi_os_release_mutex(handler_obj->address_space.
-					      context_mutex);
 			acpi_ut_remove_reference(handler_obj);
 			goto unlock_and_exit;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/exfield.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/exfield.c
@@ -330,12 +330,7 @@
 		       obj_desc->field.base_byte_offset,
 		       source_desc->buffer.pointer, data_length);
 
-		if ((obj_desc->field.region_obj->region.address ==
-		     PCC_MASTER_SUBSPACE
-		     && MASTER_SUBSPACE_COMMAND(obj_desc->field.
-						base_byte_offset))
-		    || GENERIC_SUBSPACE_COMMAND(obj_desc->field.
-						base_byte_offset)) {
+		if (MASTER_SUBSPACE_COMMAND(obj_desc->field.base_byte_offset)) {
 
 			/* Perform the write */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/exoparg1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/exoparg1.c
@@ -1007,7 +1007,8 @@
 						    (walk_state, return_desc,
 						     &temp_desc);
 						if (ACPI_FAILURE(status)) {
-							goto cleanup;
+							return_ACPI_STATUS
+							    (status);
 						}
 
 						return_desc = temp_desc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/exprep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/exprep.c
@@ -437,6 +437,9 @@
 
 		if (info->connection_node) {
 			second_desc = info->connection_node->object;
+			if (second_desc == NULL) {
+				break;
+			}
 			if (!(second_desc->common.flags & AOPOBJ_DATA_VALID)) {
 				status =
 				    acpi_ds_get_buffer_arguments(second_desc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/exregion.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/exregion.c
@@ -44,7 +44,6 @@
 	struct acpi_mem_mapping *mm = mem_info->cur_mm;
 	u32 length;
 	acpi_size map_length;
-	acpi_size page_boundary_map_length;
 #ifdef ACPI_MISALIGNMENT_NOT_SUPPORTED
 	u32 remainder;
 #endif
@@ -138,26 +137,8 @@
 		map_length = (acpi_size)
 		    ((mem_info->address + mem_info->length) - address);
 
-		/*
-		 * If mapping the entire remaining portion of the region will cross
-		 * a page boundary, just map up to the page boundary, do not cross.
-		 * On some systems, crossing a page boundary while mapping regions
-		 * can cause warnings if the pages have different attributes
-		 * due to resource management.
-		 *
-		 * This has the added benefit of constraining a single mapping to
-		 * one page, which is similar to the original code that used a 4k
-		 * maximum window.
-		 */
-		page_boundary_map_length = (acpi_size)
-		    (ACPI_ROUND_UP(address, ACPI_DEFAULT_PAGE_SIZE) - address);
-		if (page_boundary_map_length == 0) {
-			page_boundary_map_length = ACPI_DEFAULT_PAGE_SIZE;
-		}
-
-		if (map_length > page_boundary_map_length) {
-			map_length = page_boundary_map_length;
-		}
+		if (map_length > ACPI_DEFAULT_PAGE_SIZE)
+			map_length = ACPI_DEFAULT_PAGE_SIZE;
 
 		/* Create a new mapping starting at the address given */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/hwesleep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/hwesleep.c
@@ -104,7 +104,9 @@
 
 	/* Flush caches, as per ACPI specification */
 
-	ACPI_FLUSH_CPU_CACHE();
+	if (sleep_state < ACPI_STATE_S4) {
+		ACPI_FLUSH_CPU_CACHE();
+	}
 
 	status = acpi_os_enter_sleep(sleep_state, sleep_control, 0);
 	if (status == AE_CTRL_TERMINATE) {
@@ -147,17 +149,13 @@
 
 acpi_status acpi_hw_extended_wake_prep(u8 sleep_state)
 {
-	acpi_status status;
 	u8 sleep_type_value;
 
 	ACPI_FUNCTION_TRACE(hw_extended_wake_prep);
 
-	status = acpi_get_sleep_type_data(ACPI_STATE_S0,
-					  &acpi_gbl_sleep_type_a,
-					  &acpi_gbl_sleep_type_b);
-	if (ACPI_SUCCESS(status)) {
+	if (acpi_gbl_sleep_type_a_s0 != ACPI_SLEEP_TYPE_INVALID) {
 		sleep_type_value =
-		    ((acpi_gbl_sleep_type_a << ACPI_X_SLEEP_TYPE_POSITION) &
+		    ((acpi_gbl_sleep_type_a_s0 << ACPI_X_SLEEP_TYPE_POSITION) &
 		     ACPI_X_SLEEP_TYPE_MASK);
 
 		(void)acpi_write((u64)(sleep_type_value | ACPI_X_SLEEP_ENABLE),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/hwsleep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/hwsleep.c
@@ -110,7 +110,9 @@
 
 	/* Flush caches, as per ACPI specification */
 
-	ACPI_FLUSH_CPU_CACHE();
+	if (sleep_state < ACPI_STATE_S4) {
+		ACPI_FLUSH_CPU_CACHE();
+	}
 
 	status = acpi_os_enter_sleep(sleep_state, pm1a_control, pm1b_control);
 	if (status == AE_CTRL_TERMINATE) {
@@ -179,7 +181,7 @@
 
 acpi_status acpi_hw_legacy_wake_prep(u8 sleep_state)
 {
-	acpi_status status;
+	acpi_status status = AE_OK;
 	struct acpi_bit_register_info *sleep_type_reg_info;
 	struct acpi_bit_register_info *sleep_enable_reg_info;
 	u32 pm1a_control;
@@ -192,10 +194,7 @@
 	 * This is unclear from the ACPI Spec, but it is required
 	 * by some machines.
 	 */
-	status = acpi_get_sleep_type_data(ACPI_STATE_S0,
-					  &acpi_gbl_sleep_type_a,
-					  &acpi_gbl_sleep_type_b);
-	if (ACPI_SUCCESS(status)) {
+	if (acpi_gbl_sleep_type_a_s0 != ACPI_SLEEP_TYPE_INVALID) {
 		sleep_type_reg_info =
 		    acpi_hw_get_bit_register_info(ACPI_BITREG_SLEEP_TYPE);
 		sleep_enable_reg_info =
@@ -216,9 +215,9 @@
 
 			/* Insert the SLP_TYP bits */
 
-			pm1a_control |= (acpi_gbl_sleep_type_a <<
+			pm1a_control |= (acpi_gbl_sleep_type_a_s0 <<
 					 sleep_type_reg_info->bit_position);
-			pm1b_control |= (acpi_gbl_sleep_type_b <<
+			pm1b_control |= (acpi_gbl_sleep_type_b_s0 <<
 					 sleep_type_reg_info->bit_position);
 
 			/* Write the control registers and ignore any errors */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/hwvalid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/hwvalid.c
@@ -23,8 +23,8 @@
  *
  * The table is used to implement the Microsoft port access rules that
  * first appeared in Windows XP. Some ports are always illegal, and some
- * ports are only illegal if the BIOS calls _OSI with a win_XP string or
- * later (meaning that the BIOS itelf is post-XP.)
+ * ports are only illegal if the BIOS calls _OSI with nothing newer than
+ * the specific _OSI strings.
  *
  * This provides ACPICA with the desired port protections and
  * Microsoft compatibility.
@@ -145,7 +145,8 @@
 
 			/* Port illegality may depend on the _OSI calls made by the BIOS */
 
-			if (acpi_gbl_osi_data >= port_info->osi_dependency) {
+			if (port_info->osi_dependency == ACPI_ALWAYS_ILLEGAL ||
+			    acpi_gbl_osi_data == port_info->osi_dependency) {
 				ACPI_DEBUG_PRINT((ACPI_DB_VALUES,
 						  "Denied AML access to port 0x%8.8X%8.8X/%X (%s 0x%.4X-0x%.4X)\n",
 						  ACPI_FORMAT_UINT64(address),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/hwxfsleep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/hwxfsleep.c
@@ -162,8 +162,6 @@
 		return_ACPI_STATUS(status);
 	}
 
-	ACPI_FLUSH_CPU_CACHE();
-
 	status = acpi_hw_write_port(acpi_gbl_FADT.smi_command,
 				    (u32)acpi_gbl_FADT.s4_bios_request, 8);
 	if (ACPI_FAILURE(status)) {
@@ -217,6 +215,13 @@
 		return_ACPI_STATUS(status);
 	}
 
+	status = acpi_get_sleep_type_data(ACPI_STATE_S0,
+					  &acpi_gbl_sleep_type_a_s0,
+					  &acpi_gbl_sleep_type_b_s0);
+	if (ACPI_FAILURE(status)) {
+		acpi_gbl_sleep_type_a_s0 = ACPI_SLEEP_TYPE_INVALID;
+	}
+
 	/* Execute the _PTS method (Prepare To Sleep) */
 
 	arg_list.count = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/nsrepair.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/nsrepair.c
@@ -181,8 +181,9 @@
 	 * Try to fix if there was no return object. Warning if failed to fix.
 	 */
 	if (!return_object) {
-		if (expected_btypes && (!(expected_btypes & ACPI_RTYPE_NONE))) {
-			if (package_index != ACPI_NOT_PACKAGE_ELEMENT) {
+		if (expected_btypes) {
+			if (!(expected_btypes & ACPI_RTYPE_NONE) &&
+			    package_index != ACPI_NOT_PACKAGE_ELEMENT) {
 				ACPI_WARN_PREDEFINED((AE_INFO,
 						      info->full_pathname,
 						      ACPI_WARN_ALWAYS,
@@ -196,14 +197,15 @@
 				if (ACPI_SUCCESS(status)) {
 					return (AE_OK);	/* Repair was successful */
 				}
-			} else {
+			}
+
+			if (expected_btypes != ACPI_RTYPE_NONE) {
 				ACPI_WARN_PREDEFINED((AE_INFO,
 						      info->full_pathname,
 						      ACPI_WARN_ALWAYS,
 						      "Missing expected return value"));
+				return (AE_AML_NO_RETURN_VALUE);
 			}
-
-			return (AE_AML_NO_RETURN_VALUE);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/nswalk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/nswalk.c
@@ -169,6 +169,9 @@
 
 	if (start_node == ACPI_ROOT_OBJECT) {
 		start_node = acpi_gbl_root_node;
+		if (!start_node) {
+			return_ACPI_STATUS(AE_NO_NAMESPACE);
+		}
 	}
 
 	/* Null child means "get first node" */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/psargs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/psargs.c
@@ -25,6 +25,8 @@
 static union acpi_parse_object *acpi_ps_get_next_field(struct acpi_parse_state
 						       *parser_state);
 
+static void acpi_ps_free_field_list(union acpi_parse_object *start);
+
 /*******************************************************************************
  *
  * FUNCTION:    acpi_ps_get_next_package_length
@@ -685,6 +687,39 @@
 
 /*******************************************************************************
  *
+ * FUNCTION:    acpi_ps_free_field_list
+ *
+ * PARAMETERS:  start               - First Op in field list
+ *
+ * RETURN:      None.
+ *
+ * DESCRIPTION: Free all Op objects inside a field list.
+ *
+ ******************************************************************************/
+
+static void acpi_ps_free_field_list(union acpi_parse_object *start)
+{
+	union acpi_parse_object *cur = start;
+	union acpi_parse_object *next;
+	union acpi_parse_object *arg;
+
+	while (cur) {
+		next = cur->common.next;
+
+		/* AML_INT_CONNECTION_OP can have a single argument */
+
+		arg = acpi_ps_get_arg(cur, 0);
+		if (arg) {
+			acpi_ps_free_op(arg);
+		}
+
+		acpi_ps_free_op(cur);
+		cur = next;
+	}
+}
+
+/*******************************************************************************
+ *
  * FUNCTION:    acpi_ps_get_next_arg
  *
  * PARAMETERS:  walk_state          - Current state
@@ -751,6 +786,10 @@
 			while (parser_state->aml < parser_state->pkg_end) {
 				field = acpi_ps_get_next_field(parser_state);
 				if (!field) {
+					if (arg) {
+						acpi_ps_free_field_list(arg);
+					}
+
 					return_ACPI_STATUS(AE_NO_MEMORY);
 				}
 
@@ -820,6 +859,10 @@
 			    acpi_ps_get_next_namepath(walk_state, parser_state,
 						      arg,
 						      ACPI_NOT_METHOD_CALL);
+			if (ACPI_FAILURE(status)) {
+				acpi_ps_free_op(arg);
+				return_ACPI_STATUS(status);
+			}
 		} else {
 			/* Single complex argument, nothing returned */
 
@@ -854,6 +897,10 @@
 			    acpi_ps_get_next_namepath(walk_state, parser_state,
 						      arg,
 						      ACPI_POSSIBLE_METHOD_CALL);
+			if (ACPI_FAILURE(status)) {
+				acpi_ps_free_op(arg);
+				return_ACPI_STATUS(status);
+			}
 
 			if (arg->common.aml_opcode == AML_INT_METHODCALL_OP) {
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/psopcode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/psopcode.c
@@ -603,7 +603,7 @@
 
 /* 7E */ ACPI_OP("Timer", ARGP_TIMER_OP, ARGI_TIMER_OP, ACPI_TYPE_ANY,
 			 AML_CLASS_EXECUTE, AML_TYPE_EXEC_0A_0T_1R,
-			 AML_FLAGS_EXEC_0A_0T_1R),
+			 AML_FLAGS_EXEC_0A_0T_1R | AML_NO_OPERAND_RESOLVE),
 
 /* ACPI 5.0 opcodes */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/utcopy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/utcopy.c
@@ -916,13 +916,6 @@
 	status = acpi_ut_walk_package_tree(source_obj, dest_obj,
 					   acpi_ut_copy_ielement_to_ielement,
 					   walk_state);
-	if (ACPI_FAILURE(status)) {
-
-		/* On failure, delete the destination package object */
-
-		acpi_ut_remove_reference(dest_obj);
-	}
-
 	return_ACPI_STATUS(status);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/acpica/utdelete.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/acpica/utdelete.c
@@ -422,6 +422,7 @@
 			ACPI_WARNING((AE_INFO,
 				      "Obj %p, Reference Count is already zero, cannot decrement\n",
 				      object));
+			return;
 		}
 
 		ACPI_DEBUG_PRINT_RAW((ACPI_DB_ALLOCATIONS,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/apei/bert.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/apei/bert.c
@@ -30,14 +30,25 @@
 #undef pr_fmt
 #define pr_fmt(fmt) "BERT: " fmt
 
+#define ACPI_BERT_PRINT_MAX_RECORDS 5
+#define ACPI_BERT_PRINT_MAX_LEN 1024
+
 static int bert_disable;
 
+/*
+ * Print "all" the error records in the BERT table, but avoid huge spam to
+ * the console if the BIOS included oversize records, or too many records.
+ * Skipping some records here does not lose anything because the full
+ * data is available to user tools in:
+ *	/sys/firmware/acpi/tables/data/BERT
+ */
 static void __init bert_print_all(struct acpi_bert_region *region,
 				  unsigned int region_len)
 {
 	struct acpi_hest_generic_status *estatus =
 		(struct acpi_hest_generic_status *)region;
 	int remain = region_len;
+	int printed = 0, skipped = 0;
 	u32 estatus_len;
 
 	while (remain >= sizeof(struct acpi_bert_region)) {
@@ -45,21 +56,26 @@
 		if (remain < estatus_len) {
 			pr_err(FW_BUG "Truncated status block (length: %u).\n",
 			       estatus_len);
-			return;
+			break;
 		}
 
 		/* No more error records. */
 		if (!estatus->block_status)
-			return;
+			break;
 
 		if (cper_estatus_check(estatus)) {
 			pr_err(FW_BUG "Invalid error record.\n");
-			return;
+			break;
 		}
 
-		pr_info_once("Error records from previous boot:\n");
-
-		cper_estatus_print(KERN_INFO HW_ERR, estatus);
+		if (estatus_len < ACPI_BERT_PRINT_MAX_LEN &&
+		    printed < ACPI_BERT_PRINT_MAX_RECORDS) {
+			pr_info_once("Error records from previous boot:\n");
+			cper_estatus_print(KERN_INFO HW_ERR, estatus);
+			printed++;
+		} else {
+			skipped++;
+		}
 
 		/*
 		 * Because the boot error source is "one-time polled" type,
@@ -71,13 +87,16 @@
 		estatus = (void *)estatus + estatus_len;
 		remain -= estatus_len;
 	}
+
+	if (skipped)
+		pr_info(HW_ERR "Skipped %d error records\n", skipped);
 }
 
 static int __init setup_bert_disable(char *str)
 {
 	bert_disable = 1;
 
-	return 0;
+	return 1;
 }
 __setup("bert_disable", setup_bert_disable);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/apei/einj.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/apei/einj.c
@@ -544,6 +544,8 @@
 	    ((region_intersects(base_addr, size, IORESOURCE_SYSTEM_RAM, IORES_DESC_NONE)
 				!= REGION_INTERSECTS) &&
 	     (region_intersects(base_addr, size, IORESOURCE_MEM, IORES_DESC_PERSISTENT_MEMORY)
+				!= REGION_INTERSECTS) &&
+	     (region_intersects(base_addr, size, IORESOURCE_MEM, IORES_DESC_SOFT_RESERVED)
 				!= REGION_INTERSECTS)))
 		return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/apei/erst.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/apei/erst.c
@@ -891,7 +891,7 @@
 static int __init setup_erst_disable(char *str)
 {
 	erst_disable = 1;
-	return 0;
+	return 1;
 }
 
 __setup("erst_disable", setup_erst_disable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/apei/ghes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/apei/ghes.c
@@ -100,6 +100,20 @@
 }
 
 /*
+ * A platform may describe one error source for the handling of synchronous
+ * errors (e.g. MCE or SEA), or for handling asynchronous errors (e.g. SCI
+ * or External Interrupt). On x86, the HEST notifications are always
+ * asynchronous, so only SEA on ARM is delivered as a synchronous
+ * notification.
+ */
+static inline bool is_hest_sync_notify(struct ghes *ghes)
+{
+	u8 notify_type = ghes->generic->notify.type;
+
+	return notify_type == ACPI_HEST_NOTIFY_SEA;
+}
+
+/*
  * This driver isn't really modular, however for the time being,
  * continuing to use module_param is the easiest way to remain
  * compatible with existing boot arg use cases.
@@ -141,8 +155,6 @@
 static struct ghes_estatus_cache *ghes_estatus_caches[GHES_ESTATUS_CACHES_SIZE];
 static atomic_t ghes_estatus_cache_alloced;
 
-static int ghes_panic_timeout __read_mostly = 30;
-
 static void __iomem *ghes_map(u64 pfn, enum fixed_addresses fixmap_idx)
 {
 	phys_addr_t paddr;
@@ -163,7 +175,7 @@
 	clear_fixmap(fixmap_idx);
 }
 
-int ghes_estatus_pool_init(int num_ghes)
+int ghes_estatus_pool_init(unsigned int num_ghes)
 {
 	unsigned long addr, len;
 	int rc;
@@ -461,7 +473,7 @@
 }
 
 static bool ghes_handle_memory_failure(struct acpi_hest_generic_data *gdata,
-				       int sev)
+				       int sev, bool sync)
 {
 	int flags = -1;
 	int sec_sev = ghes_severity(gdata->error_severity);
@@ -475,7 +487,7 @@
 	    (gdata->flags & CPER_SEC_ERROR_THRESHOLD_EXCEEDED))
 		flags = MF_SOFT_OFFLINE;
 	if (sev == GHES_SEV_RECOVERABLE && sec_sev == GHES_SEV_RECOVERABLE)
-		flags = 0;
+		flags = sync ? MF_ACTION_REQUIRED : 0;
 
 	if (flags != -1)
 		return ghes_do_memory_failure(mem_err->physical_addr, flags);
@@ -483,9 +495,11 @@
 	return false;
 }
 
-static bool ghes_handle_arm_hw_error(struct acpi_hest_generic_data *gdata, int sev)
+static bool ghes_handle_arm_hw_error(struct acpi_hest_generic_data *gdata,
+				       int sev, bool sync)
 {
 	struct cper_sec_proc_arm *err = acpi_hest_get_payload(gdata);
+	int flags = sync ? MF_ACTION_REQUIRED : 0;
 	bool queued = false;
 	int sec_sev, i;
 	char *p;
@@ -510,7 +524,7 @@
 		 * and don't filter out 'corrected' error here.
 		 */
 		if (is_cache && has_pa) {
-			queued = ghes_do_memory_failure(err_info->physical_fault_addr, 0);
+			queued = ghes_do_memory_failure(err_info->physical_fault_addr, flags);
 			p += err_info->length;
 			continue;
 		}
@@ -631,6 +645,7 @@
 	const guid_t *fru_id = &guid_null;
 	char *fru_text = "";
 	bool queued = false;
+	bool sync = is_hest_sync_notify(ghes);
 
 	sev = ghes_severity(estatus->error_severity);
 	apei_estatus_for_each_section(estatus, gdata) {
@@ -648,13 +663,13 @@
 			ghes_edac_report_mem_error(sev, mem_err);
 
 			arch_apei_report_mem_error(sev, mem_err);
-			queued = ghes_handle_memory_failure(gdata, sev);
+			queued = ghes_handle_memory_failure(gdata, sev, sync);
 		}
 		else if (guid_equal(sec_type, &CPER_SEC_PCIE)) {
 			ghes_handle_aer(gdata);
 		}
 		else if (guid_equal(sec_type, &CPER_SEC_PROC_ARM)) {
-			queued = ghes_handle_arm_hw_error(gdata, sev);
+			queued = ghes_handle_arm_hw_error(gdata, sev, sync);
 		} else {
 			void *err = acpi_hest_get_payload(gdata);
 
@@ -841,14 +856,16 @@
 			 struct acpi_hest_generic_status *estatus,
 			 u64 buf_paddr, enum fixed_addresses fixmap_idx)
 {
+	const char *msg = GHES_PFX "Fatal hardware error";
+
 	__ghes_print_estatus(KERN_EMERG, ghes->generic, estatus);
 
 	ghes_clear_estatus(ghes, estatus, buf_paddr, fixmap_idx);
 
-	/* reboot to log the error! */
 	if (!panic_timeout)
-		panic_timeout = ghes_panic_timeout;
-	panic("Fatal hardware error!");
+		pr_emerg("%s but panic disabled\n", msg);
+
+	panic(msg);
 }
 
 static int ghes_proc(struct ghes *ghes)
@@ -985,7 +1002,7 @@
 				ghes_estatus_cache_add(generic, estatus);
 		}
 
-		if (task_work_pending && current->mm != &init_mm) {
+		if (task_work_pending && current->mm) {
 			estatus_node->task_work.func = ghes_kick_task_work;
 			estatus_node->task_work_cpu = smp_processor_id();
 			ret = task_work_add(current, &estatus_node->task_work,
@@ -1457,33 +1474,35 @@
 	.remove		= ghes_remove,
 };
 
-static int __init ghes_init(void)
+void __init ghes_init(void)
 {
 	int rc;
 
+	sdei_init();
+
 	if (acpi_disabled)
-		return -ENODEV;
+		return;
 
 	switch (hest_disable) {
 	case HEST_NOT_FOUND:
-		return -ENODEV;
+		return;
 	case HEST_DISABLED:
 		pr_info(GHES_PFX "HEST is not enabled!\n");
-		return -EINVAL;
+		return;
 	default:
 		break;
 	}
 
 	if (ghes_disable) {
 		pr_info(GHES_PFX "GHES is not enabled!\n");
-		return -EINVAL;
+		return;
 	}
 
 	ghes_nmi_init_cxt();
 
 	rc = platform_driver_register(&ghes_platform_driver);
 	if (rc)
-		goto err;
+		return;
 
 	rc = apei_osc_setup();
 	if (rc == 0 && osc_sb_apei_support_acked)
@@ -1494,9 +1513,4 @@
 		pr_info(GHES_PFX "APEI firmware first mode is enabled by APEI bit.\n");
 	else
 		pr_info(GHES_PFX "Failed to enable APEI firmware first mode.\n");
-
-	return 0;
-err:
-	return rc;
 }
-device_initcall(ghes_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/apei/hest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/apei/hest.c
@@ -223,7 +223,7 @@
 static int __init setup_hest_disable(char *str)
 {
 	hest_disable = HEST_DISABLED;
-	return 0;
+	return 1;
 }
 
 __setup("hest_disable", setup_hest_disable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/arm64/gtdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/arm64/gtdt.c
@@ -283,7 +283,7 @@
 		if (frame->virt_irq > 0)
 			acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
 		frame->virt_irq = 0;
-	} while (i-- >= 0 && gtdt_frame--);
+	} while (i-- > 0 && gtdt_frame--);
 
 	return -EINVAL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/arm64/iort.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/arm64/iort.c
@@ -1361,9 +1361,17 @@
 	res[0].start = pmcg->page0_base_address;
 	res[0].end = pmcg->page0_base_address + SZ_4K - 1;
 	res[0].flags = IORESOURCE_MEM;
-	res[1].start = pmcg->page1_base_address;
-	res[1].end = pmcg->page1_base_address + SZ_4K - 1;
-	res[1].flags = IORESOURCE_MEM;
+	/*
+	 * The initial version in DEN0049C lacked a way to describe register
+	 * page 1, which makes it broken for most PMCG implementations; in
+	 * that case, just let the driver fail gracefully if it expects to
+	 * find a second memory resource.
+	 */
+	if (node->revision > 0) {
+		res[1].start = pmcg->page1_base_address;
+		res[1].end = pmcg->page1_base_address + SZ_4K - 1;
+		res[1].flags = IORESOURCE_MEM;
+	}
 
 	if (pmcg->overflow_gsiv)
 		acpi_iort_register_irq(pmcg->overflow_gsiv, "overflow",
@@ -1373,7 +1381,10 @@
 static struct acpi_platform_list pmcg_plat_info[] __initdata = {
 	/* HiSilicon Hip08 Platform */
 	{"HISI  ", "HIP08   ", 0, ACPI_SIG_IORT, greater_than_or_equal,
-	 "Erratum #162001800", IORT_SMMU_V3_PMCG_HISI_HIP08},
+	 "Erratum #162001800, Erratum #162001900", IORT_SMMU_V3_PMCG_HISI_HIP08},
+	/* HiSilicon Hip09 Platform */
+	{"HISI  ", "HIP09   ", 0, ACPI_SIG_IORT, greater_than_or_equal,
+	 "Erratum #162001900", IORT_SMMU_V3_PMCG_HISI_HIP09},
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/battery.c
@@ -53,12 +53,17 @@
 static int battery_notification_delay_ms;
 static int battery_ac_is_broken;
 static int battery_check_pmic = 1;
+static int battery_quirk_notcharging;
 static unsigned int cache_time = 1000;
 module_param(cache_time, uint, 0644);
 MODULE_PARM_DESC(cache_time, "cache time in milliseconds");
 
 static const struct acpi_device_id battery_device_ids[] = {
 	{"PNP0C0A", 0},
+
+	/* Microsoft Surface Go 3 */
+	{"MSHW0146", 0},
+
 	{"", 0},
 };
 
@@ -169,7 +174,7 @@
 		return 1;
 
 	/* fallback to using design values for broken batteries */
-	if (battery->design_capacity == battery->capacity_now)
+	if (battery->design_capacity <= battery->capacity_now)
 		return 1;
 
 	/* we don't do any sort of metric based on percentages */
@@ -217,6 +222,8 @@
 			val->intval = POWER_SUPPLY_STATUS_CHARGING;
 		else if (acpi_battery_is_charged(battery))
 			val->intval = POWER_SUPPLY_STATUS_FULL;
+		else if (battery_quirk_notcharging)
+			val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
 		else
 			val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
 		break;
@@ -442,7 +449,7 @@
 
 			if (element->type == ACPI_TYPE_STRING ||
 			    element->type == ACPI_TYPE_BUFFER)
-				strncpy(ptr, element->string.pointer, 32);
+				strscpy(ptr, element->string.pointer, 32);
 			else if (element->type == ACPI_TYPE_INTEGER) {
 				strncpy(ptr, (u8 *)&element->integer.value,
 					sizeof(u64));
@@ -669,12 +676,18 @@
 	return count;
 }
 
-static const struct device_attribute alarm_attr = {
+static struct device_attribute alarm_attr = {
 	.attr = {.name = "alarm", .mode = 0644},
 	.show = acpi_battery_alarm_show,
 	.store = acpi_battery_alarm_store,
 };
 
+static struct attribute *acpi_battery_attrs[] = {
+	&alarm_attr.attr,
+	NULL
+};
+ATTRIBUTE_GROUPS(acpi_battery);
+
 /*
  * The Battery Hooking API
  *
@@ -688,27 +701,34 @@
 static LIST_HEAD(battery_hook_list);
 static DEFINE_MUTEX(hook_mutex);
 
-static void __battery_hook_unregister(struct acpi_battery_hook *hook, int lock)
+static void battery_hook_unregister_unlocked(struct acpi_battery_hook *hook)
 {
 	struct acpi_battery *battery;
+
 	/*
 	 * In order to remove a hook, we first need to
 	 * de-register all the batteries that are registered.
 	 */
-	if (lock)
-		mutex_lock(&hook_mutex);
 	list_for_each_entry(battery, &acpi_battery_list, list) {
 		hook->remove_battery(battery->bat);
 	}
-	list_del(&hook->list);
-	if (lock)
-		mutex_unlock(&hook_mutex);
+	list_del_init(&hook->list);
+
 	pr_info("extension unregistered: %s\n", hook->name);
 }
 
 void battery_hook_unregister(struct acpi_battery_hook *hook)
 {
-	__battery_hook_unregister(hook, 1);
+	mutex_lock(&hook_mutex);
+	/*
+	 * Ignore already unregistered battery hooks. This might happen
+	 * if a battery hook was previously unloaded due to an error when
+	 * adding a new battery.
+	 */
+	if (!list_empty(&hook->list))
+		battery_hook_unregister_unlocked(hook);
+
+	mutex_unlock(&hook_mutex);
 }
 EXPORT_SYMBOL_GPL(battery_hook_unregister);
 
@@ -717,7 +737,6 @@
 	struct acpi_battery *battery;
 
 	mutex_lock(&hook_mutex);
-	INIT_LIST_HEAD(&hook->list);
 	list_add(&hook->list, &battery_hook_list);
 	/*
 	 * Now that the driver is registered, we need
@@ -734,7 +753,7 @@
 			 * hooks.
 			 */
 			pr_err("extension failed to load: %s", hook->name);
-			__battery_hook_unregister(hook, 0);
+			battery_hook_unregister_unlocked(hook);
 			goto end;
 		}
 	}
@@ -771,7 +790,7 @@
 			 */
 			pr_err("error in extension, unloading: %s",
 					hook_node->name);
-			__battery_hook_unregister(hook_node, 0);
+			battery_hook_unregister_unlocked(hook_node);
 		}
 	}
 	mutex_unlock(&hook_mutex);
@@ -804,14 +823,17 @@
 	 * need to remove the hooks.
 	 */
 	list_for_each_entry_safe(hook, ptr, &battery_hook_list, list) {
-		__battery_hook_unregister(hook, 1);
+		battery_hook_unregister(hook);
 	}
 	mutex_destroy(&hook_mutex);
 }
 
 static int sysfs_add_battery(struct acpi_battery *battery)
 {
-	struct power_supply_config psy_cfg = { .drv_data = battery, };
+	struct power_supply_config psy_cfg = {
+		.drv_data = battery,
+		.attr_grp = acpi_battery_groups,
+	};
 	bool full_cap_broken = false;
 
 	if (!ACPI_BATTERY_CAPACITY_VALID(battery->full_charge_capacity) &&
@@ -856,7 +878,7 @@
 		return result;
 	}
 	battery_hook_add_battery(battery);
-	return device_create_file(&battery->bat->dev, &alarm_attr);
+	return 0;
 }
 
 static void sysfs_remove_battery(struct acpi_battery *battery)
@@ -867,7 +889,6 @@
 		return;
 	}
 	battery_hook_remove_battery(battery);
-	device_remove_file(&battery->bat->dev, &alarm_attr);
 	power_supply_unregister(battery->bat);
 	battery->bat = NULL;
 	mutex_unlock(&battery->sysfs_lock);
@@ -1111,6 +1132,12 @@
 	return 0;
 }
 
+static int __init battery_quirk_not_charging(const struct dmi_system_id *d)
+{
+	battery_quirk_notcharging = 1;
+	return 0;
+}
+
 static const struct dmi_system_id bat_dmi_table[] __initconst = {
 	{
 		/* NEC LZ750/LS */
@@ -1155,6 +1182,27 @@
 			DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo MIIX 320-10ICR"),
 		},
 	},
+	{
+		/*
+		 * On Lenovo ThinkPads the BIOS specification defines
+		 * a state when the bits for charging and discharging
+		 * are both set to 0. That state is "Not Charging".
+		 */
+		.callback = battery_quirk_not_charging,
+		.ident = "Lenovo ThinkPad",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad"),
+		},
+	},
+	{
+		/* Microsoft Surface Go 3 */
+		.callback = battery_notification_delay_quirk,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go 3"),
+		},
+	},
 	{},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/bus.c
@@ -98,8 +98,8 @@
 	acpi_status status;
 	unsigned long long sta;
 
-	if (acpi_device_always_present(device)) {
-		acpi_set_device_status(device, ACPI_STA_DEFAULT);
+	if (acpi_device_override_status(device, &sta)) {
+		acpi_set_device_status(device, sta);
 		return 0;
 	}
 
@@ -283,6 +283,8 @@
 bool osc_sb_native_usb4_support_confirmed;
 EXPORT_SYMBOL_GPL(osc_sb_native_usb4_support_confirmed);
 
+bool osc_sb_cppc2_support_acked;
+
 static u8 sb_uuid_str[] = "0811B06E-4A27-44F9-8D60-3CBBC22E7B48";
 static void acpi_bus_osc_negotiate_platform_control(void)
 {
@@ -312,10 +314,11 @@
 #endif
 #ifdef CONFIG_X86
 	capbuf[OSC_SUPPORT_DWORD] |= OSC_SB_GENERIC_INITIATOR_SUPPORT;
-	if (boot_cpu_has(X86_FEATURE_HWP)) {
-		capbuf[OSC_SUPPORT_DWORD] |= OSC_SB_CPC_SUPPORT;
-		capbuf[OSC_SUPPORT_DWORD] |= OSC_SB_CPCV2_SUPPORT;
-	}
+#endif
+
+#ifdef CONFIG_ACPI_CPPC_LIB
+	capbuf[OSC_SUPPORT_DWORD] |= OSC_SB_CPC_SUPPORT;
+	capbuf[OSC_SUPPORT_DWORD] |= OSC_SB_CPCV2_SUPPORT;
 #endif
 
 	if (IS_ENABLED(CONFIG_SCHED_MC_PRIO))
@@ -332,21 +335,36 @@
 	if (ACPI_FAILURE(acpi_run_osc(handle, &context)))
 		return;
 
-	kfree(context.ret.pointer);
+	capbuf_ret = context.ret.pointer;
+	if (context.ret.length <= OSC_SUPPORT_DWORD) {
+		kfree(context.ret.pointer);
+		return;
+	}
 
-	/* Now run _OSC again with query flag clear */
+	/*
+	 * Now run _OSC again with query flag clear and with the caps
+	 * supported by both the OS and the platform.
+	 */
 	capbuf[OSC_QUERY_DWORD] = 0;
+	capbuf[OSC_SUPPORT_DWORD] = capbuf_ret[OSC_SUPPORT_DWORD];
+	kfree(context.ret.pointer);
 
 	if (ACPI_FAILURE(acpi_run_osc(handle, &context)))
 		return;
 
 	capbuf_ret = context.ret.pointer;
-	osc_sb_apei_support_acked =
-		capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_APEI_SUPPORT;
-	osc_pc_lpi_support_confirmed =
-		capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_PCLPI_SUPPORT;
-	osc_sb_native_usb4_support_confirmed =
-		capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_NATIVE_USB4_SUPPORT;
+	if (context.ret.length > OSC_SUPPORT_DWORD) {
+#ifdef CONFIG_ACPI_CPPC_LIB
+		osc_sb_cppc2_support_acked = capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_CPCV2_SUPPORT;
+#endif
+
+		osc_sb_apei_support_acked =
+			capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_APEI_SUPPORT;
+		osc_pc_lpi_support_confirmed =
+			capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_PCLPI_SUPPORT;
+		osc_sb_native_usb4_support_confirmed =
+			capbuf_ret[OSC_SUPPORT_DWORD] & OSC_SB_NATIVE_USB4_SUPPORT;
+	}
 
 	kfree(context.ret.pointer);
 }
@@ -1329,6 +1347,9 @@
 
 	pci_mmcfg_late_init();
 	acpi_iort_init();
+	acpi_viot_early_init();
+	acpi_hest_init();
+	ghes_init();
 	acpi_scan_init();
 	acpi_ec_init();
 	acpi_debugfs_init();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/button.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/button.c
@@ -78,6 +78,15 @@
 		.driver_data = (void *)(long)ACPI_BUTTON_LID_INIT_DISABLED,
 	},
 	{
+		/* Nextbook Ares 8A tablet, _LID device always reports lid closed */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Insyde"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "CherryTrail"),
+			DMI_MATCH(DMI_BIOS_VERSION, "M882"),
+		},
+		.driver_data = (void *)(long)ACPI_BUTTON_LID_INIT_DISABLED,
+	},
+	{
 		/*
 		 * Lenovo Yoga 9 14ITL5, initial notification of the LID device
 		 * never happens.
@@ -121,6 +130,17 @@
 		},
 		.driver_data = (void *)(long)ACPI_BUTTON_LID_INIT_OPEN,
 	},
+	{
+		/*
+		 * Samsung galaxybook2 ,initial _LID device notification returns
+		 * lid closed.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "SAMSUNG ELECTRONICS CO., LTD."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "750XED"),
+		},
+		.driver_data = (void *)(long)ACPI_BUTTON_LID_INIT_OPEN,
+	},
 	{}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/cppc_acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/cppc_acpi.c
@@ -100,6 +100,16 @@
 				(cpc)->cpc_entry.reg.space_id ==	\
 				ACPI_ADR_SPACE_PLATFORM_COMM)
 
+/* Check if a CPC register is in SystemMemory */
+#define CPC_IN_SYSTEM_MEMORY(cpc) ((cpc)->type == ACPI_TYPE_BUFFER &&	\
+				(cpc)->cpc_entry.reg.space_id ==	\
+				ACPI_ADR_SPACE_SYSTEM_MEMORY)
+
+/* Check if a CPC register is in SystemIo */
+#define CPC_IN_SYSTEM_IO(cpc) ((cpc)->type == ACPI_TYPE_BUFFER &&	\
+				(cpc)->cpc_entry.reg.space_id ==	\
+				ACPI_ADR_SPACE_SYSTEM_IO)
+
 /* Evaluates to True if reg is a NULL register descriptor */
 #define IS_NULL_REG(reg) ((reg)->space_id ==  ACPI_ADR_SPACE_SYSTEM_MEMORY && \
 				(reg)->address == 0 &&			\
@@ -118,6 +128,8 @@
  */
 #define NUM_RETRIES 500ULL
 
+#define OVER_16BTS_MASK ~0xFFFFULL
+
 #define define_one_cppc_ro(_name)		\
 static struct kobj_attribute _name =		\
 __ATTR(_name, 0444, show_##_name, NULL)
@@ -151,6 +163,16 @@
 show_cppc_data(cppc_get_perf_ctrs, cppc_perf_fb_ctrs, reference_perf);
 show_cppc_data(cppc_get_perf_ctrs, cppc_perf_fb_ctrs, wraparound_time);
 
+/* Check for valid access_width, otherwise, fallback to using bit_width */
+#define GET_BIT_WIDTH(reg) ((reg)->access_width ? (8 << ((reg)->access_width - 1)) : (reg)->bit_width)
+
+/* Shift and apply the mask for CPC reads/writes */
+#define MASK_VAL_READ(reg, val) (((val) >> (reg)->bit_offset) &				\
+					GENMASK(((reg)->bit_width) - 1, 0))
+#define MASK_VAL_WRITE(reg, prev_val, val)						\
+	((((val) & GENMASK(((reg)->bit_width) - 1, 0)) << (reg)->bit_offset) |		\
+	((prev_val) & ~(GENMASK(((reg)->bit_width) - 1, 0) << (reg)->bit_offset)))	\
+
 static ssize_t show_feedback_ctrs(struct kobject *kobj,
 		struct kobj_attribute *attr, char *buf)
 {
@@ -411,7 +433,7 @@
 	struct cpc_desc *cpc_ptr;
 	int cpu;
 
-	for_each_possible_cpu(cpu) {
+	for_each_present_cpu(cpu) {
 		cpc_ptr = per_cpu(cpc_desc_ptr, cpu);
 		if (!cpc_ptr)
 			return false;
@@ -587,33 +609,6 @@
 	return 0;
 }
 
-/* Check if CPPC revision + num_ent combination is supported */
-static bool is_cppc_supported(int revision, int num_ent)
-{
-	int expected_num_ent;
-
-	switch (revision) {
-	case CPPC_V2_REV:
-		expected_num_ent = CPPC_V2_NUM_ENT;
-		break;
-	case CPPC_V3_REV:
-		expected_num_ent = CPPC_V3_NUM_ENT;
-		break;
-	default:
-		pr_debug("Firmware exports unsupported CPPC revision: %d\n",
-			revision);
-		return false;
-	}
-
-	if (expected_num_ent != num_ent) {
-		pr_debug("Firmware exports %d entries. Expected: %d for CPPC rev:%d\n",
-			num_ent, expected_num_ent, revision);
-		return false;
-	}
-
-	return true;
-}
-
 /*
  * An example CPC table looks like the following.
  *
@@ -683,6 +678,11 @@
 	acpi_status status;
 	int ret = -EFAULT;
 
+	if (!osc_sb_cppc2_support_acked) {
+		pr_debug("CPPC v2 _OSC not acked\n");
+		return -ENODEV;
+	}
+
 	/* Parse the ACPI _CPC table for this CPU. */
 	status = acpi_evaluate_object_typed(handle, "_CPC", NULL, &output,
 			ACPI_TYPE_PACKAGE);
@@ -703,12 +703,16 @@
 	cpc_obj = &out_obj->package.elements[0];
 	if (cpc_obj->type == ACPI_TYPE_INTEGER)	{
 		num_ent = cpc_obj->integer.value;
+		if (num_ent <= 1) {
+			pr_debug("Unexpected _CPC NumEntries value (%d) for CPU:%d\n",
+				 num_ent, pr->id);
+			goto out_free;
+		}
 	} else {
 		pr_debug("Unexpected entry type(%d) for NumEntries\n",
 				cpc_obj->type);
 		goto out_free;
 	}
-	cpc_ptr->num_entries = num_ent;
 
 	/* Second entry should be revision. */
 	cpc_obj = &out_obj->package.elements[1];
@@ -719,10 +723,32 @@
 				cpc_obj->type);
 		goto out_free;
 	}
-	cpc_ptr->version = cpc_rev;
 
-	if (!is_cppc_supported(cpc_rev, num_ent))
+	if (cpc_rev < CPPC_V2_REV) {
+		pr_debug("Unsupported _CPC Revision (%d) for CPU:%d\n", cpc_rev,
+			 pr->id);
 		goto out_free;
+	}
+
+	/*
+	 * Disregard _CPC if the number of entries in the return pachage is not
+	 * as expected, but support future revisions being proper supersets of
+	 * the v3 and only causing more entries to be returned by _CPC.
+	 */
+	if ((cpc_rev == CPPC_V2_REV && num_ent != CPPC_V2_NUM_ENT) ||
+	    (cpc_rev == CPPC_V3_REV && num_ent != CPPC_V3_NUM_ENT) ||
+	    (cpc_rev > CPPC_V3_REV && num_ent <= CPPC_V3_NUM_ENT)) {
+		pr_debug("Unexpected number of _CPC return package entries (%d) for CPU:%d\n",
+			 num_ent, pr->id);
+		goto out_free;
+	}
+	if (cpc_rev > CPPC_V3_REV) {
+		num_ent = CPPC_V3_NUM_ENT;
+		cpc_rev = CPPC_V3_REV;
+	}
+
+	cpc_ptr->num_entries = num_ent;
+	cpc_ptr->version = cpc_rev;
 
 	/* Iterate through remaining entries in _CPC */
 	for (i = 2; i < num_ent; i++) {
@@ -753,15 +779,34 @@
 			} else if (gas_t->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) {
 				if (gas_t->address) {
 					void __iomem *addr;
+					size_t access_width;
 
-					addr = ioremap(gas_t->address, gas_t->bit_width/8);
+					access_width = GET_BIT_WIDTH(gas_t) / 8;
+					addr = ioremap(gas_t->address, access_width);
 					if (!addr)
 						goto out_free;
 					cpc_ptr->cpc_regs[i-2].sys_mem_vaddr = addr;
 				}
+			} else if (gas_t->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+				if (gas_t->access_width < 1 || gas_t->access_width > 3) {
+					/*
+					 * 1 = 8-bit, 2 = 16-bit, and 3 = 32-bit.
+					 * SystemIO doesn't implement 64-bit
+					 * registers.
+					 */
+					pr_debug("Invalid access width %d for SystemIO register\n",
+						gas_t->access_width);
+					goto out_free;
+				}
+				if (gas_t->address & OVER_16BTS_MASK) {
+					/* SystemIO registers use 16-bit integer addresses */
+					pr_debug("Invalid IO port %llu for SystemIO register\n",
+						gas_t->address);
+					goto out_free;
+				}
 			} else {
 				if (gas_t->space_id != ACPI_ADR_SPACE_FIXED_HARDWARE || !cpc_ffh_supported()) {
-					/* Support only PCC ,SYS MEM and FFH type regs */
+					/* Support only PCC, SystemMemory, SystemIO, and FFH type regs. */
 					pr_debug("Unsupported register type: %d\n", gas_t->space_id);
 					goto out_free;
 				}
@@ -789,6 +834,7 @@
 
 	/* Store CPU Logical ID */
 	cpc_ptr->cpu_id = pr->id;
+	raw_spin_lock_init(&cpc_ptr->rmw_lock);
 
 	/* Parse PSD data for this CPU */
 	ret = acpi_get_psd(cpc_ptr, handle);
@@ -927,6 +973,7 @@
 {
 	int ret_val = 0;
 	void __iomem *vaddr = NULL;
+	int size;
 	int pcc_ss_id = per_cpu(cpu_pcc_subspace_idx, cpu);
 	struct cpc_reg *reg = &reg_res->cpc_entry.reg;
 
@@ -936,17 +983,38 @@
 	}
 
 	*val = 0;
-	if (reg->space_id == ACPI_ADR_SPACE_PLATFORM_COMM && pcc_ss_id >= 0)
+	size = GET_BIT_WIDTH(reg);
+
+	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+		acpi_status status;
+
+		status = acpi_os_read_port((acpi_io_address)reg->address,
+					   (u32 *)val, size);
+		if (ACPI_FAILURE(status)) {
+			pr_debug("Error: Failed to read SystemIO port %llx\n",
+				 reg->address);
+			return -EFAULT;
+		}
+
+		return 0;
+	} else if (reg->space_id == ACPI_ADR_SPACE_PLATFORM_COMM && pcc_ss_id >= 0) {
+		/*
+		 * For registers in PCC space, the register size is determined
+		 * by the bit width field; the access size is used to indicate
+		 * the PCC subspace id.
+		 */
+		size = reg->bit_width;
 		vaddr = GET_PCC_VADDR(reg->address, pcc_ss_id);
+	}
 	else if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY)
 		vaddr = reg_res->sys_mem_vaddr;
 	else if (reg->space_id == ACPI_ADR_SPACE_FIXED_HARDWARE)
 		return cpc_read_ffh(cpu, reg, val);
 	else
 		return acpi_os_read_memory((acpi_physical_address)reg->address,
-				val, reg->bit_width);
+				val, size);
 
-	switch (reg->bit_width) {
+	switch (size) {
 	case 8:
 		*val = readb_relaxed(vaddr);
 		break;
@@ -960,32 +1028,93 @@
 		*val = readq_relaxed(vaddr);
 		break;
 	default:
-		pr_debug("Error: Cannot read %u bit width from PCC for ss: %d\n",
-			 reg->bit_width, pcc_ss_id);
+		if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) {
+			pr_debug("Error: Cannot read %u bit width from system memory: 0x%llx\n",
+				size, reg->address);
+		} else if (reg->space_id == ACPI_ADR_SPACE_PLATFORM_COMM) {
+			pr_debug("Error: Cannot read %u bit width from PCC for ss: %d\n",
+				size, pcc_ss_id);
+		}
 		ret_val = -EFAULT;
 	}
 
+	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY)
+		*val = MASK_VAL_READ(reg, *val);
+
 	return ret_val;
 }
 
 static int cpc_write(int cpu, struct cpc_register_resource *reg_res, u64 val)
 {
 	int ret_val = 0;
+	int size;
+	u64 prev_val;
 	void __iomem *vaddr = NULL;
 	int pcc_ss_id = per_cpu(cpu_pcc_subspace_idx, cpu);
 	struct cpc_reg *reg = &reg_res->cpc_entry.reg;
+	struct cpc_desc *cpc_desc;
+	unsigned long flags;
+
+	size = GET_BIT_WIDTH(reg);
 
-	if (reg->space_id == ACPI_ADR_SPACE_PLATFORM_COMM && pcc_ss_id >= 0)
+	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+		acpi_status status;
+
+		status = acpi_os_write_port((acpi_io_address)reg->address,
+					    (u32)val, size);
+		if (ACPI_FAILURE(status)) {
+			pr_debug("Error: Failed to write SystemIO port %llx\n",
+				 reg->address);
+			return -EFAULT;
+		}
+
+		return 0;
+	} else if (reg->space_id == ACPI_ADR_SPACE_PLATFORM_COMM && pcc_ss_id >= 0) {
+		/*
+		 * For registers in PCC space, the register size is determined
+		 * by the bit width field; the access size is used to indicate
+		 * the PCC subspace id.
+		 */
+		size = reg->bit_width;
 		vaddr = GET_PCC_VADDR(reg->address, pcc_ss_id);
+	}
 	else if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY)
 		vaddr = reg_res->sys_mem_vaddr;
 	else if (reg->space_id == ACPI_ADR_SPACE_FIXED_HARDWARE)
 		return cpc_write_ffh(cpu, reg, val);
 	else
 		return acpi_os_write_memory((acpi_physical_address)reg->address,
-				val, reg->bit_width);
+				val, size);
+
+	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) {
+		cpc_desc = per_cpu(cpc_desc_ptr, cpu);
+		if (!cpc_desc) {
+			pr_debug("No CPC descriptor for CPU:%d\n", cpu);
+			return -ENODEV;
+		}
+
+		raw_spin_lock_irqsave(&cpc_desc->rmw_lock, flags);
+		switch (size) {
+		case 8:
+			prev_val = readb_relaxed(vaddr);
+			break;
+		case 16:
+			prev_val = readw_relaxed(vaddr);
+			break;
+		case 32:
+			prev_val = readl_relaxed(vaddr);
+			break;
+		case 64:
+			prev_val = readq_relaxed(vaddr);
+			break;
+		default:
+			raw_spin_unlock_irqrestore(&cpc_desc->rmw_lock, flags);
+			return -EFAULT;
+		}
+		val = MASK_VAL_WRITE(reg, prev_val, val);
+	}
 
-	switch (reg->bit_width) {
+	switch (size) {
 	case 8:
 		writeb_relaxed(val, vaddr);
 		break;
@@ -999,19 +1128,34 @@
 		writeq_relaxed(val, vaddr);
 		break;
 	default:
-		pr_debug("Error: Cannot write %u bit width to PCC for ss: %d\n",
-			 reg->bit_width, pcc_ss_id);
+		if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) {
+			pr_debug("Error: Cannot write %u bit width to system memory: 0x%llx\n",
+				size, reg->address);
+		} else if (reg->space_id == ACPI_ADR_SPACE_PLATFORM_COMM) {
+			pr_debug("Error: Cannot write %u bit width to PCC for ss: %d\n",
+				size, pcc_ss_id);
+		}
 		ret_val = -EFAULT;
 		break;
 	}
 
+	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY)
+		raw_spin_unlock_irqrestore(&cpc_desc->rmw_lock, flags);
+
 	return ret_val;
 }
 
 static int cppc_get_perf(int cpunum, enum cppc_regs reg_idx, u64 *perf)
 {
 	struct cpc_desc *cpc_desc = per_cpu(cpc_desc_ptr, cpunum);
-	struct cpc_register_resource *reg = &cpc_desc->cpc_regs[reg_idx];
+	struct cpc_register_resource *reg;
+
+	if (!cpc_desc) {
+		pr_debug("No CPC descriptor for CPU:%d\n", cpunum);
+		return -ENODEV;
+	}
+
+	reg = &cpc_desc->cpc_regs[reg_idx];
 
 	if (CPC_IN_PCC(reg)) {
 		int pcc_ss_id = per_cpu(cpu_pcc_subspace_idx, cpunum);
@@ -1236,6 +1380,51 @@
 EXPORT_SYMBOL_GPL(cppc_get_perf_ctrs);
 
 /**
+ * cppc_set_enable - Set to enable CPPC on the processor by writing the
+ * Continuous Performance Control package EnableRegister field.
+ * @cpu: CPU for which to enable CPPC register.
+ * @enable: 0 - disable, 1 - enable CPPC feature on the processor.
+ *
+ * Return: 0 for success, -ERRNO or -EIO otherwise.
+ */
+int cppc_set_enable(int cpu, bool enable)
+{
+	int pcc_ss_id = per_cpu(cpu_pcc_subspace_idx, cpu);
+	struct cpc_register_resource *enable_reg;
+	struct cpc_desc *cpc_desc = per_cpu(cpc_desc_ptr, cpu);
+	struct cppc_pcc_data *pcc_ss_data = NULL;
+	int ret = -EINVAL;
+
+	if (!cpc_desc) {
+		pr_debug("No CPC descriptor for CPU:%d\n", cpu);
+		return -EINVAL;
+	}
+
+	enable_reg = &cpc_desc->cpc_regs[ENABLE];
+
+	if (CPC_IN_PCC(enable_reg)) {
+
+		if (pcc_ss_id < 0)
+			return -EIO;
+
+		ret = cpc_write(cpu, enable_reg, enable);
+		if (ret)
+			return ret;
+
+		pcc_ss_data = pcc_data[pcc_ss_id];
+
+		down_write(&pcc_ss_data->pcc_lock);
+		/* after writing CPC, transfer the ownership of PCC to platfrom */
+		ret = send_pcc_cmd(pcc_ss_id, CMD_WRITE);
+		up_write(&pcc_ss_data->pcc_lock);
+		return ret;
+	}
+
+	return cpc_write(cpu, enable_reg, enable);
+}
+EXPORT_SYMBOL_GPL(cppc_set_enable);
+
+/**
  * cppc_set_perf - Set a CPU's performance controls.
  * @cpu: CPU for which to set performance controls.
  * @perf_ctrls: ptr to cppc_perf_ctrls. See cppc_acpi.h
@@ -1366,6 +1555,9 @@
  * transition latency for performance change requests. The closest we have
  * is the timing information from the PCCT tables which provides the info
  * on the number and frequency of PCC commands the platform can handle.
+ *
+ * If desired_reg is in the SystemMemory or SystemIo ACPI address space,
+ * then assume there is no latency.
  */
 unsigned int cppc_get_transition_latency(int cpu_num)
 {
@@ -1391,7 +1583,9 @@
 		return CPUFREQ_ETERNAL;
 
 	desired_reg = &cpc_desc->cpc_regs[DESIRED_PERF];
-	if (!CPC_IN_PCC(desired_reg))
+	if (CPC_IN_SYSTEM_MEMORY(desired_reg) || CPC_IN_SYSTEM_IO(desired_reg))
+		return 0;
+	else if (!CPC_IN_PCC(desired_reg))
 		return CPUFREQ_ETERNAL;
 
 	if (pcc_ss_id < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/device_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/device_sysfs.c
@@ -157,8 +157,8 @@
 		return 0;
 
 	len = snprintf(modalias, size, "acpi:");
-	if (len <= 0)
-		return len;
+	if (len >= size)
+		return -ENOMEM;
 
 	size -= len;
 
@@ -211,8 +211,10 @@
 	len = snprintf(modalias, size, "of:N%sT", (char *)buf.pointer);
 	ACPI_FREE(buf.pointer);
 
-	if (len <= 0)
-		return len;
+	if (len >= size)
+		return -ENOMEM;
+
+	size -= len;
 
 	of_compatible = acpi_dev->data.of_compatible;
 	if (of_compatible->type == ACPI_TYPE_PACKAGE) {
@@ -541,8 +543,9 @@
 	 * If device has _STR, 'description' file is created
 	 */
 	if (acpi_has_method(dev->handle, "_STR")) {
-		status = acpi_evaluate_object(dev->handle, "_STR",
-					NULL, &buffer);
+		status = acpi_evaluate_object_typed(dev->handle, "_STR",
+						    NULL, &buffer,
+						    ACPI_TYPE_BUFFER);
 		if (ACPI_FAILURE(status))
 			buffer.pointer = NULL;
 		dev->pnp.str_obj = buffer.pointer;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/ec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/ec.c
@@ -166,6 +166,7 @@
 	struct transaction transaction;
 	struct work_struct work;
 	struct acpi_ec_query_handler *handler;
+	struct acpi_ec *ec;
 };
 
 static int acpi_ec_query(struct acpi_ec *ec, u8 *data);
@@ -182,7 +183,6 @@
 static struct workqueue_struct *ec_query_wq;
 
 static int EC_FLAGS_CORRECT_ECDT; /* Needs ECDT port address correction */
-static int EC_FLAGS_IGNORE_DSDT_GPE; /* Needs ECDT GPE as correction setting */
 static int EC_FLAGS_TRUST_DSDT_GPE; /* Needs DSDT GPE as correction setting */
 static int EC_FLAGS_CLEAR_ON_RESUME; /* Needs acpi_ec_clear() on boot/resume */
 
@@ -452,6 +452,7 @@
 		ec_dbg_evt("Command(%s) submitted/blocked",
 			   acpi_ec_cmd_string(ACPI_EC_COMMAND_QUERY));
 		ec->nr_pending_queries++;
+		ec->events_in_progress++;
 		queue_work(ec_wq, &ec->work);
 	}
 }
@@ -518,7 +519,7 @@
 #ifdef CONFIG_PM_SLEEP
 static void __acpi_ec_flush_work(void)
 {
-	drain_workqueue(ec_wq); /* flush ec->work */
+	flush_workqueue(ec_wq); /* flush ec->work */
 	flush_workqueue(ec_query_wq); /* flush queries */
 }
 
@@ -772,6 +773,9 @@
 	unsigned long tmp;
 	int ret = 0;
 
+	if (t->rdata)
+		memset(t->rdata, 0, t->rlen);
+
 	/* start transaction */
 	spin_lock_irqsave(&ec->lock, tmp);
 	/* Enable GPE for command processing (IBF=0/OBF=1) */
@@ -808,8 +812,6 @@
 
 	if (!ec || (!t) || (t->wlen && !t->wdata) || (t->rlen && !t->rdata))
 		return -EINVAL;
-	if (t->rdata)
-		memset(t->rdata, 0, t->rlen);
 
 	mutex_lock(&ec->mutex);
 	if (ec->global_lock) {
@@ -836,7 +838,7 @@
 				.wdata = NULL, .rdata = &d,
 				.wlen = 0, .rlen = 1};
 
-	return acpi_ec_transaction(ec, &t);
+	return acpi_ec_transaction_unlocked(ec, &t);
 }
 
 static int acpi_ec_burst_disable(struct acpi_ec *ec)
@@ -846,7 +848,7 @@
 				.wlen = 0, .rlen = 0};
 
 	return (acpi_ec_read_status(ec) & ACPI_EC_FLAG_BURST) ?
-				acpi_ec_transaction(ec, &t) : 0;
+				acpi_ec_transaction_unlocked(ec, &t) : 0;
 }
 
 static int acpi_ec_read(struct acpi_ec *ec, u8 address, u8 *data)
@@ -862,6 +864,19 @@
 	return result;
 }
 
+static int acpi_ec_read_unlocked(struct acpi_ec *ec, u8 address, u8 *data)
+{
+	int result;
+	u8 d;
+	struct transaction t = {.command = ACPI_EC_COMMAND_READ,
+				.wdata = &address, .rdata = &d,
+				.wlen = 1, .rlen = 1};
+
+	result = acpi_ec_transaction_unlocked(ec, &t);
+	*data = d;
+	return result;
+}
+
 static int acpi_ec_write(struct acpi_ec *ec, u8 address, u8 data)
 {
 	u8 wdata[2] = { address, data };
@@ -872,6 +887,16 @@
 	return acpi_ec_transaction(ec, &t);
 }
 
+static int acpi_ec_write_unlocked(struct acpi_ec *ec, u8 address, u8 data)
+{
+	u8 wdata[2] = { address, data };
+	struct transaction t = {.command = ACPI_EC_COMMAND_WRITE,
+				.wdata = wdata, .rdata = NULL,
+				.wlen = 2, .rlen = 0};
+
+	return acpi_ec_transaction_unlocked(ec, &t);
+}
+
 int ec_read(u8 addr, u8 *val)
 {
 	int err;
@@ -1100,10 +1125,11 @@
 void acpi_ec_remove_query_handler(struct acpi_ec *ec, u8 query_bit)
 {
 	acpi_ec_remove_query_handlers(ec, false, query_bit);
+	flush_workqueue(ec_query_wq);
 }
 EXPORT_SYMBOL_GPL(acpi_ec_remove_query_handler);
 
-static struct acpi_ec_query *acpi_ec_create_query(u8 *pval)
+static struct acpi_ec_query *acpi_ec_create_query(struct acpi_ec *ec, u8 *pval)
 {
 	struct acpi_ec_query *q;
 	struct transaction *t;
@@ -1111,11 +1137,13 @@
 	q = kzalloc(sizeof (struct acpi_ec_query), GFP_KERNEL);
 	if (!q)
 		return NULL;
+
 	INIT_WORK(&q->work, acpi_ec_event_processor);
 	t = &q->transaction;
 	t->command = ACPI_EC_COMMAND_QUERY;
 	t->rdata = pval;
 	t->rlen = 1;
+	q->ec = ec;
 	return q;
 }
 
@@ -1132,13 +1160,21 @@
 {
 	struct acpi_ec_query *q = container_of(work, struct acpi_ec_query, work);
 	struct acpi_ec_query_handler *handler = q->handler;
+	struct acpi_ec *ec = q->ec;
 
 	ec_dbg_evt("Query(0x%02x) started", handler->query_bit);
+
 	if (handler->func)
 		handler->func(handler->data);
 	else if (handler->handle)
 		acpi_evaluate_object(handler->handle, NULL, NULL, NULL);
+
 	ec_dbg_evt("Query(0x%02x) stopped", handler->query_bit);
+
+	spin_lock_irq(&ec->lock);
+	ec->queries_in_progress--;
+	spin_unlock_irq(&ec->lock);
+
 	acpi_ec_delete_query(q);
 }
 
@@ -1148,7 +1184,7 @@
 	int result;
 	struct acpi_ec_query *q;
 
-	q = acpi_ec_create_query(&value);
+	q = acpi_ec_create_query(ec, &value);
 	if (!q)
 		return -ENOMEM;
 
@@ -1170,19 +1206,20 @@
 	}
 
 	/*
-	 * It is reported that _Qxx are evaluated in a parallel way on
-	 * Windows:
+	 * It is reported that _Qxx are evaluated in a parallel way on Windows:
 	 * https://bugzilla.kernel.org/show_bug.cgi?id=94411
 	 *
-	 * Put this log entry before schedule_work() in order to make
-	 * it appearing before any other log entries occurred during the
-	 * work queue execution.
+	 * Put this log entry before queue_work() to make it appear in the log
+	 * before any other messages emitted during workqueue handling.
 	 */
 	ec_dbg_evt("Query(0x%02x) scheduled", value);
-	if (!queue_work(ec_query_wq, &q->work)) {
-		ec_dbg_evt("Query(0x%02x) overlapped", value);
-		result = -EBUSY;
-	}
+
+	spin_lock_irq(&ec->lock);
+
+	ec->queries_in_progress++;
+	queue_work(ec_query_wq, &q->work);
+
+	spin_unlock_irq(&ec->lock);
 
 err_exit:
 	if (result)
@@ -1240,6 +1277,10 @@
 	ec_dbg_evt("Event stopped");
 
 	acpi_ec_check_event(ec);
+
+	spin_lock_irqsave(&ec->lock, flags);
+	ec->events_in_progress--;
+	spin_unlock_irqrestore(&ec->lock, flags);
 }
 
 static void acpi_ec_handle_interrupt(struct acpi_ec *ec)
@@ -1276,6 +1317,7 @@
 	struct acpi_ec *ec = handler_context;
 	int result = 0, i, bytes = bits / 8;
 	u8 *value = (u8 *)value64;
+	u32 glk;
 
 	if ((address > 0xFF) || !value || !handler_context)
 		return AE_BAD_PARAMETER;
@@ -1283,17 +1325,38 @@
 	if (function != ACPI_READ && function != ACPI_WRITE)
 		return AE_BAD_PARAMETER;
 
+	mutex_lock(&ec->mutex);
+
+	if (ec->global_lock) {
+		acpi_status status;
+
+		status = acpi_acquire_global_lock(ACPI_EC_UDELAY_GLK, &glk);
+		if (ACPI_FAILURE(status)) {
+			result = -ENODEV;
+			goto unlock;
+		}
+	}
+
 	if (ec->busy_polling || bits > 8)
 		acpi_ec_burst_enable(ec);
 
-	for (i = 0; i < bytes; ++i, ++address, ++value)
+	for (i = 0; i < bytes; ++i, ++address, ++value) {
 		result = (function == ACPI_READ) ?
-			acpi_ec_read(ec, address, value) :
-			acpi_ec_write(ec, address, *value);
+			acpi_ec_read_unlocked(ec, address, value) :
+			acpi_ec_write_unlocked(ec, address, *value);
+		if (result < 0)
+			break;
+	}
 
 	if (ec->busy_polling || bits > 8)
 		acpi_ec_burst_disable(ec);
 
+	if (ec->global_lock)
+		acpi_release_global_lock(glk);
+
+unlock:
+	mutex_unlock(&ec->mutex);
+
 	switch (result) {
 	case -EINVAL:
 		return AE_BAD_PARAMETER;
@@ -1301,8 +1364,10 @@
 		return AE_NOT_FOUND;
 	case -ETIME:
 		return AE_TIME;
-	default:
+	case 0:
 		return AE_OK;
+	default:
+		return AE_ERROR;
 	}
 }
 
@@ -1375,24 +1440,16 @@
 	if (ec->data_addr == 0 || ec->command_addr == 0)
 		return AE_OK;
 
-	if (boot_ec && boot_ec_is_ecdt && EC_FLAGS_IGNORE_DSDT_GPE) {
-		/*
-		 * Always inherit the GPE number setting from the ECDT
-		 * EC.
-		 */
-		ec->gpe = boot_ec->gpe;
-	} else {
-		/* Get GPE bit assignment (EC events). */
-		/* TODO: Add support for _GPE returning a package */
-		status = acpi_evaluate_integer(handle, "_GPE", NULL, &tmp);
-		if (ACPI_SUCCESS(status))
-			ec->gpe = tmp;
+	/* Get GPE bit assignment (EC events). */
+	/* TODO: Add support for _GPE returning a package */
+	status = acpi_evaluate_integer(handle, "_GPE", NULL, &tmp);
+	if (ACPI_SUCCESS(status))
+		ec->gpe = tmp;
+	/*
+	 * Errors are non-fatal, allowing for ACPI Reduced Hardware
+	 * platforms which use GpioInt instead of GPE.
+	 */
 
-		/*
-		 * Errors are non-fatal, allowing for ACPI Reduced Hardware
-		 * platforms which use GpioInt instead of GPE.
-		 */
-	}
 	/* Use the global lock for all EC transactions? */
 	tmp = 0;
 	acpi_evaluate_integer(handle, "_GLK", NULL, &tmp);
@@ -1830,60 +1887,12 @@
 	return 0;
 }
 
-/*
- * Some DSDTs contain wrong GPE setting.
- * Asus FX502VD/VE, GL702VMK, X550VXK, X580VD
- * https://bugzilla.kernel.org/show_bug.cgi?id=195651
- */
-static int ec_honor_ecdt_gpe(const struct dmi_system_id *id)
-{
-	pr_debug("Detected system needing ignore DSDT GPE setting.\n");
-	EC_FLAGS_IGNORE_DSDT_GPE = 1;
-	return 0;
-}
-
 static const struct dmi_system_id ec_dmi_table[] __initconst = {
 	{
 	ec_correct_ecdt, "MSI MS-171F", {
 	DMI_MATCH(DMI_SYS_VENDOR, "Micro-Star"),
 	DMI_MATCH(DMI_PRODUCT_NAME, "MS-171F"),}, NULL},
 	{
-	ec_honor_ecdt_gpe, "ASUS FX502VD", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "FX502VD"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUS FX502VE", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "FX502VE"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUS GL702VMK", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "GL702VMK"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUSTeK COMPUTER INC. X505BA", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "X505BA"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUSTeK COMPUTER INC. X505BP", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "X505BP"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUSTeK COMPUTER INC. X542BA", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "X542BA"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUSTeK COMPUTER INC. X542BP", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "X542BP"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUS X550VXK", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "X550VXK"),}, NULL},
-	{
-	ec_honor_ecdt_gpe, "ASUS X580VD", {
-	DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
-	DMI_MATCH(DMI_PRODUCT_NAME, "X580VD"),}, NULL},
-	{
 	/* https://bugzilla.kernel.org/show_bug.cgi?id=209989 */
 	ec_honor_dsdt_gpe, "HP Pavilion Gaming Laptop 15-cx0xxx", {
 	DMI_MATCH(DMI_SYS_VENDOR, "HP"),
@@ -2021,6 +2030,7 @@
 
 bool acpi_ec_dispatch_gpe(void)
 {
+	bool work_in_progress;
 	u32 ret;
 
 	if (!first_ec)
@@ -2041,8 +2051,19 @@
 	if (ret == ACPI_INTERRUPT_HANDLED)
 		pm_pr_dbg("ACPI EC GPE dispatched\n");
 
-	/* Flush the event and query workqueues. */
-	acpi_ec_flush_work();
+	/* Drain EC work. */
+	do {
+		acpi_ec_flush_work();
+
+		pm_pr_dbg("ACPI EC work flushed\n");
+
+		spin_lock_irq(&first_ec->lock);
+
+		work_in_progress = first_ec->events_in_progress +
+			first_ec->queries_in_progress > 0;
+
+		spin_unlock_irq(&first_ec->lock);
+	} while (work_in_progress && !pm_wakeup_pending());
 
 	return false;
 }
@@ -2139,13 +2160,6 @@
 		},
 	},
 	{
-		.ident = "ThinkPad X1 Carbon 6th",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
-			DMI_MATCH(DMI_PRODUCT_FAMILY, "ThinkPad X1 Carbon 6th"),
-		},
-	},
-	{
 		.ident = "ThinkPad X1 Yoga 3rd",
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/fan.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/fan.h
@@ -6,8 +6,52 @@
  *
  * Add new device IDs before the generic ACPI fan one.
  */
+
+#ifndef _ACPI_FAN_H_
+#define _ACPI_FAN_H_
+
 #define ACPI_FAN_DEVICE_IDS	\
 	{"INT3404", }, /* Fan */ \
 	{"INTC1044", }, /* Fan for Tiger Lake generation */ \
 	{"INTC1048", }, /* Fan for Alder Lake generation */ \
 	{"PNP0C0B", } /* Generic ACPI fan */
+
+#define ACPI_FPS_NAME_LEN	20
+
+struct acpi_fan_fps {
+	u64 control;
+	u64 trip_point;
+	u64 speed;
+	u64 noise_level;
+	u64 power;
+	char name[ACPI_FPS_NAME_LEN];
+	struct device_attribute dev_attr;
+};
+
+struct acpi_fan_fif {
+	u8 revision;
+	u8 fine_grain_ctrl;
+	u8 step_size;
+	u8 low_speed_notification;
+};
+
+struct acpi_fan_fst {
+	u64 revision;
+	u64 control;
+	u64 speed;
+};
+
+struct acpi_fan {
+	bool acpi4;
+	struct acpi_fan_fif fif;
+	struct acpi_fan_fps *fps;
+	int fps_count;
+	struct thermal_cooling_device *cdev;
+	struct device_attribute fst_speed;
+	struct device_attribute fine_grain_control;
+};
+
+int acpi_fan_get_fst(struct acpi_device *device, struct acpi_fan_fst *fst);
+int acpi_fan_create_attributes(struct acpi_device *device);
+void acpi_fan_delete_attributes(struct acpi_device *device);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/fan_attr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/fan_attr.c
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  fan_attr.c - Create extra attributes for ACPI Fan driver
+ *
+ *  Copyright (C) 2001, 2002 Andy Grover <andrew.grover@intel.com>
+ *  Copyright (C) 2001, 2002 Paul Diefenbaugh <paul.s.diefenbaugh@intel.com>
+ *  Copyright (C) 2022 Intel Corporation. All rights reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/acpi.h>
+
+#include "fan.h"
+
+MODULE_LICENSE("GPL");
+
+static ssize_t show_state(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct acpi_fan_fps *fps = container_of(attr, struct acpi_fan_fps, dev_attr);
+	int count;
+
+	if (fps->control == 0xFFFFFFFF || fps->control > 100)
+		count = scnprintf(buf, PAGE_SIZE, "not-defined:");
+	else
+		count = scnprintf(buf, PAGE_SIZE, "%lld:", fps->control);
+
+	if (fps->trip_point == 0xFFFFFFFF || fps->trip_point > 9)
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "not-defined:");
+	else
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "%lld:", fps->trip_point);
+
+	if (fps->speed == 0xFFFFFFFF)
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "not-defined:");
+	else
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "%lld:", fps->speed);
+
+	if (fps->noise_level == 0xFFFFFFFF)
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "not-defined:");
+	else
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "%lld:", fps->noise_level * 100);
+
+	if (fps->power == 0xFFFFFFFF)
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "not-defined\n");
+	else
+		count += scnprintf(&buf[count], PAGE_SIZE - count, "%lld\n", fps->power);
+
+	return count;
+}
+
+static ssize_t show_fan_speed(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct acpi_device *acpi_dev = container_of(dev, struct acpi_device, dev);
+	struct acpi_fan_fst fst;
+	int status;
+
+	status = acpi_fan_get_fst(acpi_dev, &fst);
+	if (status)
+		return status;
+
+	return sprintf(buf, "%lld\n", fst.speed);
+}
+
+static ssize_t show_fine_grain_control(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct acpi_device *acpi_dev = container_of(dev, struct acpi_device, dev);
+	struct acpi_fan *fan = acpi_driver_data(acpi_dev);
+
+	return sprintf(buf, "%d\n", fan->fif.fine_grain_ctrl);
+}
+
+int acpi_fan_create_attributes(struct acpi_device *device)
+{
+	struct acpi_fan *fan = acpi_driver_data(device);
+	int i, status;
+
+	sysfs_attr_init(&fan->fine_grain_control.attr);
+	fan->fine_grain_control.show = show_fine_grain_control;
+	fan->fine_grain_control.store = NULL;
+	fan->fine_grain_control.attr.name = "fine_grain_control";
+	fan->fine_grain_control.attr.mode = 0444;
+	status = sysfs_create_file(&device->dev.kobj, &fan->fine_grain_control.attr);
+	if (status)
+		return status;
+
+	/* _FST is present if we are here */
+	sysfs_attr_init(&fan->fst_speed.attr);
+	fan->fst_speed.show = show_fan_speed;
+	fan->fst_speed.store = NULL;
+	fan->fst_speed.attr.name = "fan_speed_rpm";
+	fan->fst_speed.attr.mode = 0444;
+	status = sysfs_create_file(&device->dev.kobj, &fan->fst_speed.attr);
+	if (status)
+		goto rem_fine_grain_attr;
+
+	for (i = 0; i < fan->fps_count; ++i) {
+		struct acpi_fan_fps *fps = &fan->fps[i];
+
+		snprintf(fps->name, ACPI_FPS_NAME_LEN, "state%d", i);
+		sysfs_attr_init(&fps->dev_attr.attr);
+		fps->dev_attr.show = show_state;
+		fps->dev_attr.store = NULL;
+		fps->dev_attr.attr.name = fps->name;
+		fps->dev_attr.attr.mode = 0444;
+		status = sysfs_create_file(&device->dev.kobj, &fps->dev_attr.attr);
+		if (status) {
+			int j;
+
+			for (j = 0; j < i; ++j)
+				sysfs_remove_file(&device->dev.kobj, &fan->fps[j].dev_attr.attr);
+			goto rem_fst_attr;
+		}
+	}
+
+	return 0;
+
+rem_fst_attr:
+	sysfs_remove_file(&device->dev.kobj, &fan->fst_speed.attr);
+
+rem_fine_grain_attr:
+	sysfs_remove_file(&device->dev.kobj, &fan->fine_grain_control.attr);
+
+	return status;
+}
+
+void acpi_fan_delete_attributes(struct acpi_device *device)
+{
+	struct acpi_fan *fan = acpi_driver_data(device);
+	int i;
+
+	for (i = 0; i < fan->fps_count; ++i)
+		sysfs_remove_file(&device->dev.kobj, &fan->fps[i].dev_attr.attr);
+
+	sysfs_remove_file(&device->dev.kobj, &fan->fst_speed.attr);
+	sysfs_remove_file(&device->dev.kobj, &fan->fine_grain_control.attr);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/fan_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/fan_core.c
@@ -0,0 +1,470 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  fan_core.c - ACPI Fan core Driver
+ *
+ *  Copyright (C) 2001, 2002 Andy Grover <andrew.grover@intel.com>
+ *  Copyright (C) 2001, 2002 Paul Diefenbaugh <paul.s.diefenbaugh@intel.com>
+ *  Copyright (C) 2022 Intel Corporation. All rights reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+#include <linux/thermal.h>
+#include <linux/acpi.h>
+#include <linux/platform_device.h>
+#include <linux/sort.h>
+
+#include "fan.h"
+
+MODULE_AUTHOR("Paul Diefenbaugh");
+MODULE_DESCRIPTION("ACPI Fan Driver");
+MODULE_LICENSE("GPL");
+
+static int acpi_fan_probe(struct platform_device *pdev);
+static int acpi_fan_remove(struct platform_device *pdev);
+
+static const struct acpi_device_id fan_device_ids[] = {
+	ACPI_FAN_DEVICE_IDS,
+	{"", 0},
+};
+MODULE_DEVICE_TABLE(acpi, fan_device_ids);
+
+#ifdef CONFIG_PM_SLEEP
+static int acpi_fan_suspend(struct device *dev);
+static int acpi_fan_resume(struct device *dev);
+static const struct dev_pm_ops acpi_fan_pm = {
+	.resume = acpi_fan_resume,
+	.freeze = acpi_fan_suspend,
+	.thaw = acpi_fan_resume,
+	.restore = acpi_fan_resume,
+};
+#define FAN_PM_OPS_PTR (&acpi_fan_pm)
+#else
+#define FAN_PM_OPS_PTR NULL
+#endif
+
+static struct platform_driver acpi_fan_driver = {
+	.probe = acpi_fan_probe,
+	.remove = acpi_fan_remove,
+	.driver = {
+		.name = "acpi-fan",
+		.acpi_match_table = fan_device_ids,
+		.pm = FAN_PM_OPS_PTR,
+	},
+};
+
+/* thermal cooling device callbacks */
+static int fan_get_max_state(struct thermal_cooling_device *cdev, unsigned long
+			     *state)
+{
+	struct acpi_device *device = cdev->devdata;
+	struct acpi_fan *fan = acpi_driver_data(device);
+
+	if (fan->acpi4) {
+		if (fan->fif.fine_grain_ctrl)
+			*state = 100 / fan->fif.step_size;
+		else
+			*state = fan->fps_count - 1;
+	} else {
+		*state = 1;
+	}
+
+	return 0;
+}
+
+int acpi_fan_get_fst(struct acpi_device *device, struct acpi_fan_fst *fst)
+{
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *obj;
+	acpi_status status;
+	int ret = 0;
+
+	status = acpi_evaluate_object(device->handle, "_FST", NULL, &buffer);
+	if (ACPI_FAILURE(status)) {
+		dev_err(&device->dev, "Get fan state failed\n");
+		return status;
+	}
+
+	obj = buffer.pointer;
+	if (!obj || obj->type != ACPI_TYPE_PACKAGE ||
+	    obj->package.count != 3 ||
+	    obj->package.elements[1].type != ACPI_TYPE_INTEGER) {
+		dev_err(&device->dev, "Invalid _FST data\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	fst->revision = obj->package.elements[0].integer.value;
+	fst->control = obj->package.elements[1].integer.value;
+	fst->speed = obj->package.elements[2].integer.value;
+
+err:
+	kfree(obj);
+	return ret;
+}
+
+static int fan_get_state_acpi4(struct acpi_device *device, unsigned long *state)
+{
+	struct acpi_fan *fan = acpi_driver_data(device);
+	struct acpi_fan_fst fst;
+	int status, i;
+
+	status = acpi_fan_get_fst(device, &fst);
+	if (status)
+		return status;
+
+	if (fan->fif.fine_grain_ctrl) {
+		/* This control should be same what we set using _FSL by spec */
+		if (fst.control > 100) {
+			dev_dbg(&device->dev, "Invalid control value returned\n");
+			goto match_fps;
+		}
+
+		*state = (int) fst.control / fan->fif.step_size;
+		return 0;
+	}
+
+match_fps:
+	for (i = 0; i < fan->fps_count; i++) {
+		if (fst.control == fan->fps[i].control)
+			break;
+	}
+	if (i == fan->fps_count) {
+		dev_dbg(&device->dev, "Invalid control value returned\n");
+		return -EINVAL;
+	}
+
+	*state = i;
+
+	return status;
+}
+
+static int fan_get_state(struct acpi_device *device, unsigned long *state)
+{
+	int result;
+	int acpi_state = ACPI_STATE_D0;
+
+	result = acpi_device_update_power(device, &acpi_state);
+	if (result)
+		return result;
+
+	*state = acpi_state == ACPI_STATE_D3_COLD
+			|| acpi_state == ACPI_STATE_D3_HOT ?
+		0 : (acpi_state == ACPI_STATE_D0 ? 1 : -1);
+	return 0;
+}
+
+static int fan_get_cur_state(struct thermal_cooling_device *cdev, unsigned long
+			     *state)
+{
+	struct acpi_device *device = cdev->devdata;
+	struct acpi_fan *fan = acpi_driver_data(device);
+
+	if (fan->acpi4)
+		return fan_get_state_acpi4(device, state);
+	else
+		return fan_get_state(device, state);
+}
+
+static int fan_set_state(struct acpi_device *device, unsigned long state)
+{
+	if (state != 0 && state != 1)
+		return -EINVAL;
+
+	return acpi_device_set_power(device,
+				     state ? ACPI_STATE_D0 : ACPI_STATE_D3_COLD);
+}
+
+static int fan_set_state_acpi4(struct acpi_device *device, unsigned long state)
+{
+	struct acpi_fan *fan = acpi_driver_data(device);
+	acpi_status status;
+	u64 value = state;
+	int max_state;
+
+	if (fan->fif.fine_grain_ctrl)
+		max_state = 100 / fan->fif.step_size;
+	else
+		max_state = fan->fps_count - 1;
+
+	if (state > max_state)
+		return -EINVAL;
+
+	if (fan->fif.fine_grain_ctrl) {
+		value *= fan->fif.step_size;
+		/* Spec allows compensate the last step only */
+		if (value + fan->fif.step_size > 100)
+			value = 100;
+	} else {
+		value = fan->fps[state].control;
+	}
+
+	status = acpi_execute_simple_method(device->handle, "_FSL", value);
+	if (ACPI_FAILURE(status)) {
+		dev_dbg(&device->dev, "Failed to set state by _FSL\n");
+		return status;
+	}
+
+	return 0;
+}
+
+static int
+fan_set_cur_state(struct thermal_cooling_device *cdev, unsigned long state)
+{
+	struct acpi_device *device = cdev->devdata;
+	struct acpi_fan *fan = acpi_driver_data(device);
+
+	if (fan->acpi4)
+		return fan_set_state_acpi4(device, state);
+	else
+		return fan_set_state(device, state);
+}
+
+static const struct thermal_cooling_device_ops fan_cooling_ops = {
+	.get_max_state = fan_get_max_state,
+	.get_cur_state = fan_get_cur_state,
+	.set_cur_state = fan_set_cur_state,
+};
+
+/* --------------------------------------------------------------------------
+ *                               Driver Interface
+ * --------------------------------------------------------------------------
+*/
+
+static bool acpi_fan_is_acpi4(struct acpi_device *device)
+{
+	return acpi_has_method(device->handle, "_FIF") &&
+	       acpi_has_method(device->handle, "_FPS") &&
+	       acpi_has_method(device->handle, "_FSL") &&
+	       acpi_has_method(device->handle, "_FST");
+}
+
+static int acpi_fan_get_fif(struct acpi_device *device)
+{
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	struct acpi_fan *fan = acpi_driver_data(device);
+	struct acpi_buffer format = { sizeof("NNNN"), "NNNN" };
+	u64 fields[4];
+	struct acpi_buffer fif = { sizeof(fields), fields };
+	union acpi_object *obj;
+	acpi_status status;
+
+	status = acpi_evaluate_object(device->handle, "_FIF", NULL, &buffer);
+	if (ACPI_FAILURE(status))
+		return status;
+
+	obj = buffer.pointer;
+	if (!obj || obj->type != ACPI_TYPE_PACKAGE) {
+		dev_err(&device->dev, "Invalid _FIF data\n");
+		status = -EINVAL;
+		goto err;
+	}
+
+	status = acpi_extract_package(obj, &format, &fif);
+	if (ACPI_FAILURE(status)) {
+		dev_err(&device->dev, "Invalid _FIF element\n");
+		status = -EINVAL;
+	}
+
+	fan->fif.revision = fields[0];
+	fan->fif.fine_grain_ctrl = fields[1];
+	fan->fif.step_size = fields[2];
+	fan->fif.low_speed_notification = fields[3];
+
+	/* If there is a bug in step size and set as 0, change to 1 */
+	if (!fan->fif.step_size)
+		fan->fif.step_size = 1;
+	/* If step size > 9, change to 9 (by spec valid values 1-9) */
+	else if (fan->fif.step_size > 9)
+		fan->fif.step_size = 9;
+err:
+	kfree(obj);
+	return status;
+}
+
+static int acpi_fan_speed_cmp(const void *a, const void *b)
+{
+	const struct acpi_fan_fps *fps1 = a;
+	const struct acpi_fan_fps *fps2 = b;
+	return fps1->speed - fps2->speed;
+}
+
+static int acpi_fan_get_fps(struct acpi_device *device)
+{
+	struct acpi_fan *fan = acpi_driver_data(device);
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *obj;
+	acpi_status status;
+	int i;
+
+	status = acpi_evaluate_object(device->handle, "_FPS", NULL, &buffer);
+	if (ACPI_FAILURE(status))
+		return status;
+
+	obj = buffer.pointer;
+	if (!obj || obj->type != ACPI_TYPE_PACKAGE || obj->package.count < 2) {
+		dev_err(&device->dev, "Invalid _FPS data\n");
+		status = -EINVAL;
+		goto err;
+	}
+
+	fan->fps_count = obj->package.count - 1; /* minus revision field */
+	fan->fps = devm_kcalloc(&device->dev,
+				fan->fps_count, sizeof(struct acpi_fan_fps),
+				GFP_KERNEL);
+	if (!fan->fps) {
+		dev_err(&device->dev, "Not enough memory\n");
+		status = -ENOMEM;
+		goto err;
+	}
+	for (i = 0; i < fan->fps_count; i++) {
+		struct acpi_buffer format = { sizeof("NNNNN"), "NNNNN" };
+		struct acpi_buffer fps = { offsetof(struct acpi_fan_fps, name),
+						&fan->fps[i] };
+		status = acpi_extract_package(&obj->package.elements[i + 1],
+					      &format, &fps);
+		if (ACPI_FAILURE(status)) {
+			dev_err(&device->dev, "Invalid _FPS element\n");
+			goto err;
+		}
+	}
+
+	/* sort the state array according to fan speed in increase order */
+	sort(fan->fps, fan->fps_count, sizeof(*fan->fps),
+	     acpi_fan_speed_cmp, NULL);
+
+err:
+	kfree(obj);
+	return status;
+}
+
+static int acpi_fan_probe(struct platform_device *pdev)
+{
+	int result = 0;
+	struct thermal_cooling_device *cdev;
+	struct acpi_fan *fan;
+	struct acpi_device *device = ACPI_COMPANION(&pdev->dev);
+	char *name;
+
+	fan = devm_kzalloc(&pdev->dev, sizeof(*fan), GFP_KERNEL);
+	if (!fan) {
+		dev_err(&device->dev, "No memory for fan\n");
+		return -ENOMEM;
+	}
+	device->driver_data = fan;
+	platform_set_drvdata(pdev, fan);
+
+	if (acpi_fan_is_acpi4(device)) {
+		result = acpi_fan_get_fif(device);
+		if (result)
+			return result;
+
+		result = acpi_fan_get_fps(device);
+		if (result)
+			return result;
+
+		result = acpi_fan_create_attributes(device);
+		if (result)
+			return result;
+
+		fan->acpi4 = true;
+	} else {
+		result = acpi_device_update_power(device, NULL);
+		if (result) {
+			dev_err(&device->dev, "Failed to set initial power state\n");
+			goto err_end;
+		}
+	}
+
+	if (!strncmp(pdev->name, "PNP0C0B", strlen("PNP0C0B")))
+		name = "Fan";
+	else
+		name = acpi_device_bid(device);
+
+	cdev = thermal_cooling_device_register(name, device,
+						&fan_cooling_ops);
+	if (IS_ERR(cdev)) {
+		result = PTR_ERR(cdev);
+		goto err_end;
+	}
+
+	dev_dbg(&pdev->dev, "registered as cooling_device%d\n", cdev->id);
+
+	fan->cdev = cdev;
+	result = sysfs_create_link(&pdev->dev.kobj,
+				   &cdev->device.kobj,
+				   "thermal_cooling");
+	if (result) {
+		dev_err(&pdev->dev, "Failed to create sysfs link 'thermal_cooling'\n");
+		goto err_unregister;
+	}
+
+	result = sysfs_create_link(&cdev->device.kobj,
+				   &pdev->dev.kobj,
+				   "device");
+	if (result) {
+		dev_err(&pdev->dev, "Failed to create sysfs link 'device'\n");
+		goto err_remove_link;
+	}
+
+	return 0;
+
+err_remove_link:
+	sysfs_remove_link(&pdev->dev.kobj, "thermal_cooling");
+err_unregister:
+	thermal_cooling_device_unregister(cdev);
+err_end:
+	if (fan->acpi4)
+		acpi_fan_delete_attributes(device);
+
+	return result;
+}
+
+static int acpi_fan_remove(struct platform_device *pdev)
+{
+	struct acpi_fan *fan = platform_get_drvdata(pdev);
+
+	if (fan->acpi4) {
+		struct acpi_device *device = ACPI_COMPANION(&pdev->dev);
+
+		acpi_fan_delete_attributes(device);
+	}
+	sysfs_remove_link(&pdev->dev.kobj, "thermal_cooling");
+	sysfs_remove_link(&fan->cdev->device.kobj, "device");
+	thermal_cooling_device_unregister(fan->cdev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int acpi_fan_suspend(struct device *dev)
+{
+	struct acpi_fan *fan = dev_get_drvdata(dev);
+	if (fan->acpi4)
+		return 0;
+
+	acpi_device_set_power(ACPI_COMPANION(dev), ACPI_STATE_D0);
+
+	return AE_OK;
+}
+
+static int acpi_fan_resume(struct device *dev)
+{
+	int result;
+	struct acpi_fan *fan = dev_get_drvdata(dev);
+
+	if (fan->acpi4)
+		return 0;
+
+	result = acpi_device_update_power(ACPI_COMPANION(dev), NULL);
+	if (result)
+		dev_err(dev, "Error updating fan power state\n");
+
+	return result;
+}
+#endif
+
+module_platform_driver(acpi_fan_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/internal.h
@@ -183,6 +183,8 @@
 	struct work_struct work;
 	unsigned long timestamp;
 	unsigned long nr_pending_queries;
+	unsigned int events_in_progress;
+	unsigned int queries_in_progress;
 	bool busy_polling;
 	unsigned int polling_guard;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/irq.c
@@ -52,6 +52,7 @@
 		      int polarity)
 {
 	struct irq_fwspec fwspec;
+	unsigned int irq;
 
 	if (WARN_ON(!acpi_gsi_domain_id)) {
 		pr_warn("GSI: No registered irqchip, giving up\n");
@@ -63,7 +64,11 @@
 	fwspec.param[1] = acpi_dev_get_irq_type(trigger, polarity);
 	fwspec.param_count = 2;
 
-	return irq_create_fwspec_mapping(&fwspec);
+	irq = irq_create_fwspec_mapping(&fwspec);
+	if (!irq)
+		return -EINVAL;
+
+	return irq;
 }
 EXPORT_SYMBOL_GPL(acpi_register_gsi);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/nfit/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/nfit/core.c
@@ -454,8 +454,13 @@
 	if (cmd_rc)
 		*cmd_rc = -EINVAL;
 
-	if (cmd == ND_CMD_CALL)
+	if (cmd == ND_CMD_CALL) {
+		if (!buf || buf_len < sizeof(*call_pkg))
+			return -EINVAL;
+
 		call_pkg = buf;
+	}
+
 	func = cmd_to_func(nfit_mem, cmd, call_pkg, &family);
 	if (func < 0)
 		return func;
@@ -480,7 +485,7 @@
 		cmd_mask = nd_desc->cmd_mask;
 		if (cmd == ND_CMD_CALL && call_pkg->nd_family) {
 			family = call_pkg->nd_family;
-			if (family > NVDIMM_BUS_FAMILY_MAX ||
+			if (call_pkg->nd_family > NVDIMM_BUS_FAMILY_MAX ||
 			    !test_bit(family, &nd_desc->bus_family_mask))
 				return -EINVAL;
 			family = array_index_nospec(family,
@@ -3676,8 +3681,8 @@
 
 	mutex_lock(&acpi_desc->init_mutex);
 	set_bit(ARS_CANCEL, &acpi_desc->scrub_flags);
-	cancel_delayed_work_sync(&acpi_desc->dwork);
 	mutex_unlock(&acpi_desc->init_mutex);
+	cancel_delayed_work_sync(&acpi_desc->dwork);
 
 	/*
 	 * Bounce the nvdimm bus lock to make sure any in-flight
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/numa/hmat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/numa/hmat.c
@@ -563,17 +563,26 @@
 {
 	struct memory_initiator *ia;
 	struct memory_initiator *ib;
-	unsigned long *p_nodes = priv;
 
 	ia = list_entry(a, struct memory_initiator, node);
 	ib = list_entry(b, struct memory_initiator, node);
 
-	set_bit(ia->processor_pxm, p_nodes);
-	set_bit(ib->processor_pxm, p_nodes);
-
 	return ia->processor_pxm - ib->processor_pxm;
 }
 
+static int initiators_to_nodemask(unsigned long *p_nodes)
+{
+	struct memory_initiator *initiator;
+
+	if (list_empty(&initiators))
+		return -ENXIO;
+
+	list_for_each_entry(initiator, &initiators, node)
+		set_bit(initiator->processor_pxm, p_nodes);
+
+	return 0;
+}
+
 static void hmat_register_target_initiators(struct memory_target *target)
 {
 	static DECLARE_BITMAP(p_nodes, MAX_NUMNODES);
@@ -610,7 +619,10 @@
 	 * initiators.
 	 */
 	bitmap_zero(p_nodes, MAX_NUMNODES);
-	list_sort(p_nodes, &initiators, initiator_cmp);
+	list_sort(NULL, &initiators, initiator_cmp);
+	if (initiators_to_nodemask(p_nodes) < 0)
+		return;
+
 	if (!access0done) {
 		for (i = WRITE_LATENCY; i <= READ_BANDWIDTH; i++) {
 			loc = localities_types[i];
@@ -644,8 +656,9 @@
 
 	/* Access 1 ignores Generic Initiators */
 	bitmap_zero(p_nodes, MAX_NUMNODES);
-	list_sort(p_nodes, &initiators, initiator_cmp);
-	best = 0;
+	if (initiators_to_nodemask(p_nodes) < 0)
+		return;
+
 	for (i = WRITE_LATENCY; i <= READ_BANDWIDTH; i++) {
 		loc = localities_types[i];
 		if (!loc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/osi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/osi.c
@@ -468,6 +468,77 @@
 	},
 
 	/*
+	 * The following Lenovo models have a broken workaround in the
+	 * acpi_video backlight implementation to meet the Windows 8
+	 * requirement of 101 backlight levels. Reverting to pre-Win8
+	 * behavior fixes the problem.
+	 */
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad L430",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad L430"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad T430",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad T430"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad T430s",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad T430s"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad T530",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad T530"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad W530",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad W530"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad X1 Carbon",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad X1 Carbon"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad X230",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad X230"),
+		},
+	},
+	{
+	.callback = dmi_disable_osi_win8,
+	.ident = "Lenovo ThinkPad Edge E330",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		     DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad Edge E330"),
+		},
+	},
+
+	/*
 	 * BIOS invocation of _OSI(Linux) is almost always a BIOS bug.
 	 * Linux ignores it, except for the machines enumerated below.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/pci_mcfg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/pci_mcfg.c
@@ -41,6 +41,8 @@
 static struct mcfg_fixup mcfg_quirks[] = {
 /*	{ OEM_ID, OEM_TABLE_ID, REV, SEGMENT, BUS_RANGE, ops, cfgres }, */
 
+#ifdef CONFIG_ARM64
+
 #define AL_ECAM(table_id, rev, seg, ops) \
 	{ "AMAZON", table_id, rev, seg, MCFG_BUS_ANY, ops }
 
@@ -169,6 +171,7 @@
 	ALTRA_ECAM_QUIRK(1, 13),
 	ALTRA_ECAM_QUIRK(1, 14),
 	ALTRA_ECAM_QUIRK(1, 15),
+#endif /* ARM64 */
 };
 
 static char mcfg_oem_id[ACPI_OEM_ID_SIZE];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/pci_root.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/pci_root.c
@@ -22,8 +22,6 @@
 #include <linux/slab.h>
 #include <linux/dmi.h>
 #include <linux/platform_data/x86/apple.h>
-#include <acpi/apei.h>	/* for acpi_hest_init() */
-
 #include "internal.h"
 
 #define ACPI_PCI_ROOT_CLASS		"pci_bridge"
@@ -938,7 +936,6 @@
 
 void __init acpi_pci_root_init(void)
 {
-	acpi_hest_init();
 	if (acpi_pci_disabled)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/pmic/intel_pmic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/pmic/intel_pmic.c
@@ -211,31 +211,36 @@
 		void *handler_context, void *region_context)
 {
 	struct intel_pmic_opregion *opregion = region_context;
-	int result = 0;
+	int result = -EINVAL;
 
-	switch (address) {
-	case 0:
-		return AE_OK;
-	case 1:
-		opregion->ctx.addr |= (*value64 & 0xff) << 8;
-		return AE_OK;
-	case 2:
-		opregion->ctx.addr |= *value64 & 0xff;
-		return AE_OK;
-	case 3:
-		opregion->ctx.val = *value64 & 0xff;
-		return AE_OK;
-	case 4:
-		if (*value64) {
-			result = regmap_write(opregion->regmap, opregion->ctx.addr,
-					      opregion->ctx.val);
-		} else {
-			result = regmap_read(opregion->regmap, opregion->ctx.addr,
-					     &opregion->ctx.val);
-			if (result == 0)
-				*value64 = opregion->ctx.val;
+	if (function == ACPI_WRITE) {
+		switch (address) {
+		case 0:
+			return AE_OK;
+		case 1:
+			opregion->ctx.addr |= (*value64 & 0xff) << 8;
+			return AE_OK;
+		case 2:
+			opregion->ctx.addr |= *value64 & 0xff;
+			return AE_OK;
+		case 3:
+			opregion->ctx.val = *value64 & 0xff;
+			return AE_OK;
+		case 4:
+			if (*value64) {
+				result = regmap_write(opregion->regmap, opregion->ctx.addr,
+						      opregion->ctx.val);
+			} else {
+				result = regmap_read(opregion->regmap, opregion->ctx.addr,
+						     &opregion->ctx.val);
+			}
+			opregion->ctx.addr = 0;
 		}
-		memset(&opregion->ctx, 0x00, sizeof(opregion->ctx));
+	}
+
+	if (function == ACPI_READ && address == 3) {
+		*value64 = opregion->ctx.val;
+		return AE_OK;
 	}
 
 	if (result < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/pmic/tps68470_pmic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/pmic/tps68470_pmic.c
@@ -376,10 +376,8 @@
 	struct tps68470_pmic_opregion *opregion;
 	acpi_status status;
 
-	if (!dev || !tps68470_regmap) {
-		dev_warn(dev, "dev or regmap is NULL\n");
-		return -EINVAL;
-	}
+	if (!tps68470_regmap)
+		return dev_err_probe(dev, -EINVAL, "regmap is missing\n");
 
 	if (!handle) {
 		dev_warn(dev, "acpi handle is NULL\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/power.c
@@ -52,7 +52,6 @@
 	u32 order;
 	unsigned int ref_count;
 	u8 state;
-	bool wakeup_enabled;
 	struct mutex resource_lock;
 	struct list_head dependents;
 };
@@ -615,20 +614,19 @@
 
 	list_for_each_entry(entry, list, node) {
 		struct acpi_power_resource *resource = entry->resource;
-		int result;
 		u8 state;
 
 		mutex_lock(&resource->resource_lock);
 
-		result = acpi_power_get_state(resource, &state);
-		if (result) {
-			mutex_unlock(&resource->resource_lock);
-			return result;
-		}
-		if (state == ACPI_POWER_RESOURCE_STATE_ON) {
-			resource->ref_count++;
-			resource->wakeup_enabled = true;
-		}
+		/*
+		 * Make sure that the power resource state and its reference
+		 * counter value are consistent with each other.
+		 */
+		if (!resource->ref_count &&
+		    !acpi_power_get_state(resource, &state) &&
+		    state == ACPI_POWER_RESOURCE_STATE_ON)
+			__acpi_power_off(resource);
+
 		if (system_level > resource->system_level)
 			system_level = resource->system_level;
 
@@ -711,7 +709,6 @@
  */
 int acpi_enable_wakeup_device_power(struct acpi_device *dev, int sleep_state)
 {
-	struct acpi_power_resource_entry *entry;
 	int err = 0;
 
 	if (!dev || !dev->wakeup.flags.valid)
@@ -722,26 +719,13 @@
 	if (dev->wakeup.prepare_count++)
 		goto out;
 
-	list_for_each_entry(entry, &dev->wakeup.resources, node) {
-		struct acpi_power_resource *resource = entry->resource;
-
-		mutex_lock(&resource->resource_lock);
-
-		if (!resource->wakeup_enabled) {
-			err = acpi_power_on_unlocked(resource);
-			if (!err)
-				resource->wakeup_enabled = true;
-		}
-
-		mutex_unlock(&resource->resource_lock);
-
-		if (err) {
-			dev_err(&dev->dev,
-				"Cannot turn wakeup power resources on\n");
-			dev->wakeup.flags.valid = 0;
-			goto out;
-		}
+	err = acpi_power_on_list(&dev->wakeup.resources);
+	if (err) {
+		dev_err(&dev->dev, "Cannot turn on wakeup power resources\n");
+		dev->wakeup.flags.valid = 0;
+		goto out;
 	}
+
 	/*
 	 * Passing 3 as the third argument below means the device may be
 	 * put into arbitrary power state afterward.
@@ -771,39 +755,31 @@
 
 	mutex_lock(&acpi_device_lock);
 
-	if (--dev->wakeup.prepare_count > 0)
+	/* Do nothing if wakeup power has not been enabled for this device. */
+	if (dev->wakeup.prepare_count <= 0)
 		goto out;
 
-	/*
-	 * Executing the code below even if prepare_count is already zero when
-	 * the function is called may be useful, for example for initialisation.
-	 */
-	if (dev->wakeup.prepare_count < 0)
-		dev->wakeup.prepare_count = 0;
+	if (--dev->wakeup.prepare_count > 0)
+		goto out;
 
 	err = acpi_device_sleep_wake(dev, 0, 0, 0);
 	if (err)
 		goto out;
 
+	/*
+	 * All of the power resources in the list need to be turned off even if
+	 * there are errors.
+	 */
 	list_for_each_entry(entry, &dev->wakeup.resources, node) {
-		struct acpi_power_resource *resource = entry->resource;
-
-		mutex_lock(&resource->resource_lock);
-
-		if (resource->wakeup_enabled) {
-			err = acpi_power_off_unlocked(resource);
-			if (!err)
-				resource->wakeup_enabled = false;
-		}
-
-		mutex_unlock(&resource->resource_lock);
+		int ret;
 
-		if (err) {
-			dev_err(&dev->dev,
-				"Cannot turn wakeup power resources off\n");
-			dev->wakeup.flags.valid = 0;
-			break;
-		}
+		ret = acpi_power_off(entry->resource);
+		if (ret && !err)
+			err = ret;
+	}
+	if (err) {
+		dev_err(&dev->dev, "Cannot turn off wakeup power resources\n");
+		dev->wakeup.flags.valid = 0;
 	}
 
  out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/prmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/prmt.c
@@ -49,12 +49,11 @@
 };
 #pragma pack()
 
-
 static LIST_HEAD(prm_module_list);
 
 struct prm_handler_info {
-	guid_t guid;
-	u64 handler_addr;
+	efi_guid_t guid;
+	void *handler_addr;
 	u64 static_data_buffer_addr;
 	u64 acpi_param_buffer_addr;
 
@@ -73,22 +72,24 @@
 	struct prm_handler_info handlers[];
 };
 
-
-static u64 efi_pa_va_lookup(u64 pa)
+static u64 efi_pa_va_lookup(efi_guid_t *guid, u64 pa)
 {
 	efi_memory_desc_t *md;
 	u64 pa_offset = pa & ~PAGE_MASK;
 	u64 page = pa & PAGE_MASK;
 
 	for_each_efi_memory_desc(md) {
-		if (md->phys_addr < pa && pa < md->phys_addr + PAGE_SIZE * md->num_pages)
+		if ((md->attribute & EFI_MEMORY_RUNTIME) &&
+		    (md->phys_addr < pa && pa < md->phys_addr + PAGE_SIZE * md->num_pages)) {
 			return pa_offset + md->virt_addr + page - md->phys_addr;
+		}
 	}
 
+	pr_warn("Failed to find VA for GUID: %pUL, PA: 0x%llx", guid, pa);
+
 	return 0;
 }
 
-
 #define get_first_handler(a) ((struct acpi_prmt_handler_info *) ((char *) (a) + a->handler_info_offset))
 #define get_next_handler(a) ((struct acpi_prmt_handler_info *) (sizeof(struct acpi_prmt_handler_info) + (char *) a))
 
@@ -139,9 +140,15 @@
 		th = &tm->handlers[cur_handler];
 
 		guid_copy(&th->guid, (guid_t *)handler_info->handler_guid);
-		th->handler_addr = efi_pa_va_lookup(handler_info->handler_address);
-		th->static_data_buffer_addr = efi_pa_va_lookup(handler_info->static_data_buffer_address);
-		th->acpi_param_buffer_addr = efi_pa_va_lookup(handler_info->acpi_param_buffer_address);
+		th->handler_addr =
+			(void *)efi_pa_va_lookup(&th->guid, handler_info->handler_address);
+
+		th->static_data_buffer_addr =
+			efi_pa_va_lookup(&th->guid, handler_info->static_data_buffer_address);
+
+		th->acpi_param_buffer_addr =
+			efi_pa_va_lookup(&th->guid, handler_info->acpi_param_buffer_address);
+
 	} while (++cur_handler < tm->handler_count && (handler_info = get_next_handler(handler_info)));
 
 	return 0;
@@ -171,7 +178,6 @@
 	return NULL;
 }
 
-
 static struct prm_module_info *find_prm_module(const guid_t *guid)
 {
 	return (struct prm_module_info *)find_guid_info(guid, GET_MODULE);
@@ -219,6 +225,11 @@
 	efi_status_t status;
 	struct prm_context_buffer context;
 
+	if (!efi_enabled(EFI_RUNTIME_SERVICES)) {
+		pr_err_ratelimited("PRM: EFI runtime services no longer available\n");
+		return AE_NO_HANDLER;
+	}
+
 	/*
 	 * The returned acpi_status will always be AE_OK. Error values will be
 	 * saved in the first byte of the PRM message buffer to be used by ASL.
@@ -231,6 +242,13 @@
 		if (!handler || !module)
 			goto invalid_guid;
 
+		if (!handler->handler_addr ||
+		    !handler->static_data_buffer_addr ||
+		    !handler->acpi_param_buffer_addr) {
+			buffer->prm_status = PRM_HANDLER_ERROR;
+			return AE_OK;
+		}
+
 		ACPI_COPY_NAMESEG(context.signature, "PRMC");
 		context.revision = 0x0;
 		context.reserved = 0x0;
@@ -308,6 +326,11 @@
 
 	pr_info("PRM: found %u modules\n", mc);
 
+	if (!efi_enabled(EFI_RUNTIME_SERVICES)) {
+		pr_err("PRM: EFI runtime services unavailable\n");
+		return;
+	}
+
 	status = acpi_install_address_space_handler(ACPI_ROOT_OBJECT,
 						    ACPI_ADR_SPACE_PLATFORM_RT,
 						    &acpi_platformrt_space_handler,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/processor_idle.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/processor_idle.c
@@ -16,7 +16,6 @@
 #include <linux/acpi.h>
 #include <linux/dmi.h>
 #include <linux/sched.h>       /* need_resched() */
-#include <linux/sort.h>
 #include <linux/tick.h>
 #include <linux/cpuidle.h>
 #include <linux/cpu.h>
@@ -266,6 +265,10 @@
 			 ACPI_CX_DESC_LEN, "ACPI P_LVL3 IOPORT 0x%x",
 			 pr->power.states[ACPI_STATE_C3].address);
 
+	if (!pr->power.states[ACPI_STATE_C2].address &&
+	    !pr->power.states[ACPI_STATE_C3].address)
+		return -ENODEV;
+
 	return 0;
 }
 
@@ -385,28 +388,24 @@
 	return;
 }
 
-static int acpi_cst_latency_cmp(const void *a, const void *b)
+static void acpi_cst_latency_sort(struct acpi_processor_cx *states, size_t length)
 {
-	const struct acpi_processor_cx *x = a, *y = b;
+	int i, j, k;
 
-	if (!(x->valid && y->valid))
-		return 0;
-	if (x->latency > y->latency)
-		return 1;
-	if (x->latency < y->latency)
-		return -1;
-	return 0;
-}
-static void acpi_cst_latency_swap(void *a, void *b, int n)
-{
-	struct acpi_processor_cx *x = a, *y = b;
-	u32 tmp;
+	for (i = 1; i < length; i++) {
+		if (!states[i].valid)
+			continue;
 
-	if (!(x->valid && y->valid))
-		return;
-	tmp = x->latency;
-	x->latency = y->latency;
-	y->latency = tmp;
+		for (j = i - 1, k = i; j >= 0; j--) {
+			if (!states[j].valid)
+				continue;
+
+			if (states[j].latency > states[k].latency)
+				swap(states[j].latency, states[k].latency);
+
+			k = j;
+		}
+	}
 }
 
 static int acpi_processor_power_verify(struct acpi_processor *pr)
@@ -451,10 +450,7 @@
 
 	if (buggy_latency) {
 		pr_notice("FW issue: working around C-state latencies out of order\n");
-		sort(&pr->power.states[1], max_cstate,
-		     sizeof(struct acpi_processor_cx),
-		     acpi_cst_latency_cmp,
-		     acpi_cst_latency_swap);
+		acpi_cst_latency_sort(&pr->power.states[1], max_cstate);
 	}
 
 	lapic_timer_propagate_broadcast(pr);
@@ -531,10 +527,27 @@
 	/* No delay is needed if we are in guest */
 	if (boot_cpu_has(X86_FEATURE_HYPERVISOR))
 		return;
+	/*
+	 * Modern (>=Nehalem) Intel systems use ACPI via intel_idle,
+	 * not this code.  Assume that any Intel systems using this
+	 * are ancient and may need the dummy wait.  This also assumes
+	 * that the motivating chipset issue was Intel-only.
+	 */
+	if (boot_cpu_data.x86_vendor != X86_VENDOR_INTEL)
+		return;
 #endif
-	/* Dummy wait op - must do something useless after P_LVL2 read
-	   because chipsets cannot guarantee that STPCLK# signal
-	   gets asserted in time to freeze execution properly. */
+	/*
+	 * Dummy wait op - must do something useless after P_LVL2 read
+	 * because chipsets cannot guarantee that STPCLK# signal gets
+	 * asserted in time to freeze execution properly
+	 *
+	 * This workaround has been in place since the original ACPI
+	 * implementation was merged, circa 2002.
+	 *
+	 * If a profile is pointing to this instruction, please first
+	 * consider moving your system to a more modern idle
+	 * mechanism.
+	 */
 	inl(acpi_gbl_FADT.xpm_timer_block.address);
 }
 
@@ -604,7 +617,7 @@
  * @cx: Target state context
  * @index: index of target state
  */
-static int acpi_idle_enter_bm(struct cpuidle_driver *drv,
+static int __cpuidle acpi_idle_enter_bm(struct cpuidle_driver *drv,
 			       struct acpi_processor *pr,
 			       struct acpi_processor_cx *cx,
 			       int index)
@@ -661,7 +674,7 @@
 	return index;
 }
 
-static int acpi_idle_enter(struct cpuidle_device *dev,
+static int __cpuidle acpi_idle_enter(struct cpuidle_device *dev,
 			   struct cpuidle_driver *drv, int index)
 {
 	struct acpi_processor_cx *cx = per_cpu(acpi_cstate[index], dev->cpu);
@@ -690,7 +703,7 @@
 	return index;
 }
 
-static int acpi_idle_enter_s2idle(struct cpuidle_device *dev,
+static int __cpuidle acpi_idle_enter_s2idle(struct cpuidle_device *dev,
 				  struct cpuidle_driver *drv, int index)
 {
 	struct acpi_processor_cx *cx = per_cpu(acpi_cstate[index], dev->cpu);
@@ -789,9 +802,11 @@
 		state->enter = acpi_idle_enter;
 
 		state->flags = 0;
-		if (cx->type == ACPI_STATE_C1 || cx->type == ACPI_STATE_C2) {
+		if (cx->type == ACPI_STATE_C1 || cx->type == ACPI_STATE_C2 ||
+		    cx->type == ACPI_STATE_C3) {
 			state->enter_dead = acpi_idle_play_dead;
-			drv->safe_state_index = count;
+			if (cx->type != ACPI_STATE_C3)
+				drv->safe_state_index = count;
 		}
 		/*
 		 * Halt-induced C1 is not good for ->enter_s2idle, because it
@@ -1075,6 +1090,11 @@
 	return 0;
 }
 
+int __weak acpi_processor_ffh_lpi_probe(unsigned int cpu)
+{
+	return -EOPNOTSUPP;
+}
+
 static int acpi_processor_get_lpi_info(struct acpi_processor *pr)
 {
 	int ret, i;
@@ -1083,6 +1103,11 @@
 	struct acpi_device *d = NULL;
 	struct acpi_lpi_states_array info[2], *tmp, *prev, *curr;
 
+	/* make sure our architecture has support */
+	ret = acpi_processor_ffh_lpi_probe(pr->id);
+	if (ret == -EOPNOTSUPP)
+		return ret;
+
 	if (!osc_pc_lpi_support_confirmed)
 		return -EOPNOTSUPP;
 
@@ -1134,11 +1159,6 @@
 	return 0;
 }
 
-int __weak acpi_processor_ffh_lpi_probe(unsigned int cpu)
-{
-	return -ENODEV;
-}
-
 int __weak acpi_processor_ffh_lpi_enter(struct acpi_lpi_state *lpi)
 {
 	return -ENODEV;
@@ -1400,6 +1420,8 @@
 		acpi_processor_registered--;
 		if (acpi_processor_registered == 0)
 			cpuidle_unregister_driver(&acpi_idle_driver);
+
+		kfree(dev);
 	}
 
 	pr->flags.power_setup_done = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/processor_pdc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/processor_pdc.c
@@ -14,6 +14,8 @@
 #include <linux/acpi.h>
 #include <acpi/processor.h>
 
+#include <xen/xen.h>
+
 #include "internal.h"
 
 static bool __init processor_physically_present(acpi_handle handle)
@@ -47,6 +49,15 @@
 		return false;
 	}
 
+	if (xen_initial_domain())
+		/*
+		 * When running as a Xen dom0 the number of processors Linux
+		 * sees can be different from the real number of processors on
+		 * the system, and we still need to execute _PDC for all of
+		 * them.
+		 */
+		return xen_processor_present(acpi_id);
+
 	type = (acpi_type == ACPI_TYPE_DEVICE) ? 1 : 0;
 	cpuid = acpi_get_cpuid(handle, type, acpi_id);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/processor_perflib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/processor_perflib.c
@@ -53,6 +53,8 @@
 {
 	acpi_status status = 0;
 	unsigned long long ppc = 0;
+	s32 qos_value;
+	int index;
 	int ret;
 
 	if (!pr)
@@ -72,17 +74,30 @@
 		}
 	}
 
+	index = ppc;
+
+	if (pr->performance_platform_limit == index ||
+	    ppc >= pr->performance->state_count)
+		return 0;
+
 	pr_debug("CPU %d: _PPC is %d - frequency %s limited\n", pr->id,
-		       (int)ppc, ppc ? "" : "not");
+		 index, index ? "is" : "is not");
 
-	pr->performance_platform_limit = (int)ppc;
+	pr->performance_platform_limit = index;
 
-	if (ppc >= pr->performance->state_count ||
-	    unlikely(!freq_qos_request_active(&pr->perflib_req)))
+	if (unlikely(!freq_qos_request_active(&pr->perflib_req)))
 		return 0;
 
-	ret = freq_qos_update_request(&pr->perflib_req,
-			pr->performance->states[ppc].core_frequency * 1000);
+	/*
+	 * If _PPC returns 0, it means that all of the available states can be
+	 * used ("no limit").
+	 */
+	if (index == 0)
+		qos_value = FREQ_QOS_MAX_DEFAULT_VALUE;
+	else
+		qos_value = pr->performance->states[index].core_frequency * 1000;
+
+	ret = freq_qos_update_request(&pr->perflib_req, qos_value);
 	if (ret < 0) {
 		pr_warn("Failed to update perflib freq constraint: CPU%d (%d)\n",
 			pr->id, ret);
@@ -165,9 +180,16 @@
 		if (!pr)
 			continue;
 
+		/*
+		 * Reset performance_platform_limit in case there is a stale
+		 * value in it, so as to make it match the "no limit" QoS value
+		 * below.
+		 */
+		pr->performance_platform_limit = 0;
+
 		ret = freq_qos_add_request(&policy->constraints,
-					   &pr->perflib_req,
-					   FREQ_QOS_MAX, INT_MAX);
+					   &pr->perflib_req, FREQ_QOS_MAX,
+					   FREQ_QOS_MAX_DEFAULT_VALUE);
 		if (ret < 0)
 			pr_err("Failed to add freq constraint for CPU%d (%d)\n",
 			       cpu, ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/processor_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/processor_thermal.c
@@ -144,7 +144,7 @@
 	unsigned int cpu;
 
 	for_each_cpu(cpu, policy->related_cpus) {
-		struct acpi_processor *pr = per_cpu(processors, policy->cpu);
+		struct acpi_processor *pr = per_cpu(processors, cpu);
 
 		if (pr)
 			freq_qos_remove_request(&pr->thermal_req);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/property.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/property.c
@@ -155,10 +155,10 @@
 	return acpi_nondev_subnode_data_ok(handle, link, list, parent);
 }
 
-static int acpi_add_nondev_subnodes(acpi_handle scope,
-				    const union acpi_object *links,
-				    struct list_head *list,
-				    struct fwnode_handle *parent)
+static bool acpi_add_nondev_subnodes(acpi_handle scope,
+				     const union acpi_object *links,
+				     struct list_head *list,
+				     struct fwnode_handle *parent)
 {
 	bool ret = false;
 	int i;
@@ -433,6 +433,16 @@
 		acpi_extract_apple_properties(adev);
 }
 
+static void acpi_free_device_properties(struct list_head *list)
+{
+	struct acpi_device_properties *props, *tmp;
+
+	list_for_each_entry_safe(props, tmp, list, list) {
+		list_del(&props->list);
+		kfree(props);
+	}
+}
+
 static void acpi_destroy_nondev_subnodes(struct list_head *list)
 {
 	struct acpi_data_node *dn, *next;
@@ -445,22 +455,18 @@
 		wait_for_completion(&dn->kobj_done);
 		list_del(&dn->sibling);
 		ACPI_FREE((void *)dn->data.pointer);
+		acpi_free_device_properties(&dn->data.properties);
 		kfree(dn);
 	}
 }
 
 void acpi_free_properties(struct acpi_device *adev)
 {
-	struct acpi_device_properties *props, *tmp;
-
 	acpi_destroy_nondev_subnodes(&adev->data.subnodes);
 	ACPI_FREE((void *)adev->data.pointer);
 	adev->data.of_compatible = NULL;
 	adev->data.pointer = NULL;
-	list_for_each_entry_safe(props, tmp, &adev->data.properties, list) {
-		list_del(&props->list);
-		kfree(props);
-	}
+	acpi_free_device_properties(&adev->data.properties);
 }
 
 /**
@@ -633,6 +639,7 @@
  * @index: Index of the reference to return
  * @num_args: Maximum number of arguments after each reference
  * @args: Location to store the returned reference with optional arguments
+ *	  (may be NULL)
  *
  * Find property with @name, verifify that it is a package containing at least
  * one object reference and if so, store the ACPI device object pointer to the
@@ -685,12 +692,15 @@
 	 */
 	if (obj->type == ACPI_TYPE_LOCAL_REFERENCE) {
 		if (index)
-			return -EINVAL;
+			return -ENOENT;
 
 		ret = acpi_bus_get_device(obj->reference.handle, &device);
 		if (ret)
 			return ret == -ENODEV ? -EINVAL : ret;
 
+		if (!args)
+			return 0;
+
 		args->fwnode = acpi_fwnode_handle(device);
 		args->nargs = 0;
 		return 0;
@@ -1090,15 +1100,10 @@
 		/* All data nodes have parent pointer so just return that */
 		return to_acpi_data_node(fwnode)->parent;
 	} else if (is_acpi_device_node(fwnode)) {
-		acpi_handle handle, parent_handle;
+		struct device *dev = to_acpi_device_node(fwnode)->dev.parent;
 
-		handle = to_acpi_device_node(fwnode)->handle;
-		if (ACPI_SUCCESS(acpi_get_parent(handle, &parent_handle))) {
-			struct acpi_device *adev;
-
-			if (!acpi_bus_get_device(parent_handle, &adev))
-				return acpi_fwnode_handle(adev);
-		}
+		if (dev)
+			return acpi_fwnode_handle(to_acpi_device(dev));
 	}
 
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/resource.c
@@ -16,6 +16,7 @@
 #include <linux/ioport.h>
 #include <linux/slab.h>
 #include <linux/irq.h>
+#include <linux/dmi.h>
 
 #ifdef CONFIG_X86
 #define valid_IRQ(i) (((i) != 0) && ((i) != 2))
@@ -249,6 +250,9 @@
 	switch (addr->resource_type) {
 	case ACPI_MEMORY_RANGE:
 		acpi_dev_memresource_flags(res, len, wp);
+
+		if (addr->info.mem.caching == ACPI_PREFETCHABLE_MEMORY)
+			res->flags |= IORESOURCE_PREFETCH;
 		break;
 	case ACPI_IO_RANGE:
 		acpi_dev_ioresource_flags(res, len, iodec,
@@ -264,9 +268,6 @@
 	if (addr->producer_consumer == ACPI_PRODUCER)
 		res->flags |= IORESOURCE_WINDOW;
 
-	if (addr->info.mem.caching == ACPI_PREFETCHABLE_MEMORY)
-		res->flags |= IORESOURCE_PREFETCH;
-
 	return !(res->flags & IORESOURCE_DISABLED);
 }
 
@@ -380,9 +381,328 @@
 }
 EXPORT_SYMBOL_GPL(acpi_dev_get_irq_type);
 
+static const struct dmi_system_id medion_laptop[] = {
+	{
+		.ident = "MEDION P15651",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "MEDION"),
+			DMI_MATCH(DMI_BOARD_NAME, "M15T"),
+		},
+	},
+	{
+		.ident = "MEDION S17405",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "MEDION"),
+			DMI_MATCH(DMI_BOARD_NAME, "M17T"),
+		},
+	},
+	{
+		.ident = "MEDION S17413",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "MEDION"),
+			DMI_MATCH(DMI_BOARD_NAME, "M1xA"),
+		},
+	},
+	{ }
+};
+
+static const struct dmi_system_id asus_laptop[] = {
+	{
+		.ident = "Asus Vivobook K3402ZA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "K3402ZA"),
+		},
+	},
+	{
+		.ident = "Asus Vivobook K3502ZA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "K3502ZA"),
+		},
+	},
+	{
+		.ident = "Asus Vivobook S5402ZA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "S5402ZA"),
+		},
+	},
+	{
+		.ident = "Asus Vivobook S5602ZA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "S5602ZA"),
+		},
+	},
+	{
+		.ident = "Asus ExpertBook B1502CBA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "B1502CBA"),
+		},
+	},
+	{
+		/* Asus Vivobook X1404VAP */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "X1404VAP"),
+		},
+	},
+	{
+		/* Asus Vivobook X1504VAP */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "X1504VAP"),
+		},
+	},
+	{
+		/* Asus Vivobook X1704VAP */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "X1704VAP"),
+		},
+	},
+	{
+		.ident = "Asus ExpertBook B2402CBA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "B2402CBA"),
+		},
+	},
+	{
+		.ident = "Asus ExpertBook B2502",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "B2502CBA"),
+		},
+	},
+	{ }
+};
+
+static const struct dmi_system_id lenovo_laptop[] = {
+	{
+		.ident = "LENOVO IdeaPad Flex 5 14ALC7",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "82R9"),
+		},
+	},
+	{
+		.ident = "Asus ExpertBook B1402CBA",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "B1402CBA"),
+		},
+	},
+	{
+		/* Asus ExpertBook B1402CVA */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "B1402CVA"),
+		},
+	},
+	{
+		.ident = "LENOVO IdeaPad Flex 5 16ALC7",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "82RA"),
+		},
+	},
+	{ }
+};
+
+static const struct dmi_system_id tongfang_gm_rg[] = {
+	{
+		.ident = "TongFang GMxRGxx/XMG CORE 15 (M22)/TUXEDO Stellaris 15 Gen4 AMD",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxRGxx"),
+		},
+	},
+	{
+		/* LG Electronics 16T90SP */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LG Electronics"),
+			DMI_MATCH(DMI_BOARD_NAME, "16T90SP"),
+		},
+	},
+	{ }
+};
+
+static const struct dmi_system_id maingear_laptop[] = {
+	{
+		.ident = "MAINGEAR Vector Pro 2 15",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Micro Electronics Inc"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MG-VCP2-15A3070T"),
+		}
+	},
+	{
+		/* Asus ExpertBook B2502CVA */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "B2502CVA"),
+		},
+	},
+	{
+		/* TongFang GMxXGxx/TUXEDO Polaris 15 Gen5 AMD */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxXGxx"),
+		},
+	},
+	{
+		/* TongFang GMxXGxX/TUXEDO Polaris 15 Gen5 AMD */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxXGxX"),
+		},
+	},
+	{
+		/* TongFang GMxXGxx sold as Eluktronics Inc. RP-15 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Eluktronics Inc."),
+			DMI_MATCH(DMI_BOARD_NAME, "RP-15"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Eluktronics Inc."),
+			DMI_MATCH(DMI_BOARD_NAME, "MECH-17"),
+		},
+	},
+	{
+		/* TongFang GM6XGxX/TUXEDO Stellaris 16 Gen5 AMD */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GM6XGxX"),
+		},
+	},
+	{
+		.ident = "MAINGEAR Vector Pro 2 17",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Micro Electronics Inc"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MG-VCP2-17A3070T"),
+		},
+	},
+	{ }
+};
+
+static const struct dmi_system_id lg_laptop[] = {
+	{
+		.ident = "LG Electronics 17U70P",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LG Electronics"),
+			DMI_MATCH(DMI_BOARD_NAME, "17U70P"),
+		},
+	},
+	{
+		/* Infinity E15-5A165-BM */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GM5RG1E0009COM"),
+		},
+	},
+	{
+		/* Infinity E15-5A305-1M */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GM5RGEE0016COM"),
+		},
+	},
+	{
+		/* Lunnen Ground 15 / AMD Ryzen 5 5500U */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Lunnen"),
+			DMI_MATCH(DMI_BOARD_NAME, "LLL5DAW"),
+		},
+	},
+	{
+		/* Lunnen Ground 16 / AMD Ryzen 7 5800U */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Lunnen"),
+			DMI_MATCH(DMI_BOARD_NAME, "LL6FA"),
+		},
+	},
+	{
+		/* MAIBENBEN X577 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "MAIBENBEN"),
+			DMI_MATCH(DMI_BOARD_NAME, "X577"),
+		},
+	},
+	{
+		/* TongFang GXxHRXx/TUXEDO InfinityBook Pro Gen9 AMD */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GXxHRXx"),
+		},
+	},
+	{
+		/* TongFang GMxHGxx/TUXEDO Stellaris Slim Gen1 AMD */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxHGxx"),
+		},
+	},
+	{
+		/*
+		 * TongFang GM5HG0A in case of the SKIKK Vanaheim relabel the
+		 * board-name is changed, so check OEM strings instead. Note
+		 * OEM string matches are always exact matches.
+		 * https://bugzilla.kernel.org/show_bug.cgi?id=219614
+		 */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_OEM_STRING, "GM5HG0A"),
+		},
+	},
+	{ }
+};
+
+struct irq_override_cmp {
+	const struct dmi_system_id *system;
+	unsigned char irq;
+	unsigned char triggering;
+	unsigned char polarity;
+	unsigned char shareable;
+	bool override;
+};
+
+static const struct irq_override_cmp override_table[] = {
+	{ medion_laptop, 1, ACPI_LEVEL_SENSITIVE, ACPI_ACTIVE_LOW, 0, false },
+	{ asus_laptop, 1, ACPI_LEVEL_SENSITIVE, ACPI_ACTIVE_LOW, 0, false },
+	{ lenovo_laptop, 6, ACPI_LEVEL_SENSITIVE, ACPI_ACTIVE_LOW, 0, true },
+	{ lenovo_laptop, 10, ACPI_LEVEL_SENSITIVE, ACPI_ACTIVE_LOW, 0, true },
+	{ tongfang_gm_rg, 1, ACPI_EDGE_SENSITIVE, ACPI_ACTIVE_LOW, 1, true },
+	{ maingear_laptop, 1, ACPI_EDGE_SENSITIVE, ACPI_ACTIVE_LOW, 1, true },
+	{ lg_laptop, 1, ACPI_LEVEL_SENSITIVE, ACPI_ACTIVE_LOW, 0, false },
+};
+
+static bool acpi_dev_irq_override(u32 gsi, u8 triggering, u8 polarity,
+				  u8 shareable)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(override_table); i++) {
+		const struct irq_override_cmp *entry = &override_table[i];
+
+		if (entry->irq == gsi &&
+		    entry->triggering == triggering &&
+		    entry->polarity == polarity &&
+		    entry->shareable == shareable &&
+		    dmi_check_system(entry->system))
+			return entry->override;
+	}
+
+#ifdef CONFIG_X86
+	/*
+	 * IRQ override isn't needed on modern AMD Zen systems and
+	 * this override breaks active low IRQs on AMD Ryzen 6000 and
+	 * newer systems. Skip it.
+	 */
+	if (boot_cpu_has(X86_FEATURE_ZEN))
+		return false;
+#endif
+
+	return true;
+}
+
 static void acpi_dev_get_irqresource(struct resource *res, u32 gsi,
 				     u8 triggering, u8 polarity, u8 shareable,
-				     bool legacy)
+				     bool check_override)
 {
 	int irq, p, t;
 
@@ -401,7 +721,9 @@
 	 * using extended IRQ descriptors we take the IRQ configuration
 	 * from _CRS directly.
 	 */
-	if (legacy && !acpi_get_override_irq(gsi, &t, &p)) {
+	if (check_override &&
+	    acpi_dev_irq_override(gsi, triggering, polarity, shareable) &&
+	    !acpi_get_override_irq(gsi, &t, &p)) {
 		u8 trig = t ? ACPI_LEVEL_SENSITIVE : ACPI_EDGE_SENSITIVE;
 		u8 pol = p ? ACPI_ACTIVE_LOW : ACPI_ACTIVE_HIGH;
 
@@ -657,6 +979,23 @@
 EXPORT_SYMBOL_GPL(acpi_dev_get_dma_resources);
 
 /**
+ * acpi_dev_get_memory_resources - Get current memory resources of a device.
+ * @adev: ACPI device node to get the resources for.
+ * @list: Head of the resultant list of resources (must be empty).
+ *
+ * This is a helper function that locates all memory type resources of @adev
+ * with acpi_dev_get_resources().
+ *
+ * The number of resources in the output list is returned on success, an error
+ * code reflecting the error condition is returned otherwise.
+ */
+int acpi_dev_get_memory_resources(struct acpi_device *adev, struct list_head *list)
+{
+	return acpi_dev_get_resources(adev, list, is_memory, NULL);
+}
+EXPORT_SYMBOL_GPL(acpi_dev_get_memory_resources);
+
+/**
  * acpi_dev_filter_resource_type - Filter ACPI resource according to resource
  *				   types
  * @ares: Input ACPI resource object.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/sbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/sbs.c
@@ -77,7 +77,6 @@
 	u16 spec;
 	u8 id;
 	u8 present:1;
-	u8 have_sysfs_alarm:1;
 };
 
 #define to_acpi_battery(x) power_supply_get_drvdata(x)
@@ -462,12 +461,18 @@
 	return count;
 }
 
-static const struct device_attribute alarm_attr = {
+static struct device_attribute alarm_attr = {
 	.attr = {.name = "alarm", .mode = 0644},
 	.show = acpi_battery_alarm_show,
 	.store = acpi_battery_alarm_store,
 };
 
+static struct attribute *acpi_battery_attrs[] = {
+	&alarm_attr.attr,
+	NULL
+};
+ATTRIBUTE_GROUPS(acpi_battery);
+
 /* --------------------------------------------------------------------------
                                  Driver Interface
    -------------------------------------------------------------------------- */
@@ -509,7 +514,10 @@
 static int acpi_battery_add(struct acpi_sbs *sbs, int id)
 {
 	struct acpi_battery *battery = &sbs->battery[id];
-	struct power_supply_config psy_cfg = { .drv_data = battery, };
+	struct power_supply_config psy_cfg = {
+		.drv_data = battery,
+		.attr_grp = acpi_battery_groups,
+	};
 	int result;
 
 	battery->id = id;
@@ -539,10 +547,6 @@
 		goto end;
 	}
 
-	result = device_create_file(&battery->bat->dev, &alarm_attr);
-	if (result)
-		goto end;
-	battery->have_sysfs_alarm = 1;
       end:
 	pr_info("%s [%s]: Battery Slot [%s] (battery %s)\n",
 	       ACPI_SBS_DEVICE_NAME, acpi_device_bid(sbs->device),
@@ -554,11 +558,8 @@
 {
 	struct acpi_battery *battery = &sbs->battery[id];
 
-	if (battery->bat) {
-		if (battery->have_sysfs_alarm)
-			device_remove_file(&battery->bat->dev, &alarm_attr);
+	if (battery->bat)
 		power_supply_unregister(battery->bat);
-	}
 }
 
 static int acpi_charger_add(struct acpi_sbs *sbs)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/scan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/scan.c
@@ -315,18 +315,14 @@
 		 * again).
 		 */
 		if (adev->handler) {
-			dev_warn(&adev->dev, "Already enumerated\n");
-			return -EALREADY;
+			dev_dbg(&adev->dev, "Already enumerated\n");
+			return 0;
 		}
 		error = acpi_bus_scan(adev->handle);
 		if (error) {
 			dev_warn(&adev->dev, "Namespace scan failure\n");
 			return error;
 		}
-		if (!adev->handler) {
-			dev_warn(&adev->dev, "Enumeration failure\n");
-			error = -ENODEV;
-		}
 	} else {
 		error = acpi_scan_device_not_present(adev);
 	}
@@ -793,6 +789,7 @@
 static const char * const acpi_ignore_dep_ids[] = {
 	"PNP0D80", /* Windows-compatible System Power Management Controller */
 	"INT33BD", /* Intel Baytrail Mailbox Device */
+	"LATT2021", /* Lattice FW Update Client Driver */
 	NULL
 };
 
@@ -1690,19 +1687,31 @@
 {
 	struct list_head resource_list;
 	bool is_serial_bus_slave = false;
+	static const struct acpi_device_id ignore_serial_bus_ids[] = {
 	/*
-	 * These devices have multiple I2cSerialBus resources and an i2c-client
-	 * must be instantiated for each, each with its own i2c_device_id.
-	 * Normally we only instantiate an i2c-client for the first resource,
-	 * using the ACPI HID as id. These special cases are handled by the
-	 * drivers/platform/x86/i2c-multi-instantiate.c driver, which knows
-	 * which i2c_device_id to use for each resource.
+	 * These devices have multiple SerialBus resources and a client
+	 * device must be instantiated for each of them, each with
+	 * its own device id.
+	 * Normally we only instantiate one client device for the first
+	 * resource, using the ACPI HID as id. These special cases are handled
+	 * by the drivers/platform/x86/serial-multi-instantiate.c driver, which
+	 * knows which client device id to use for each resource.
 	 */
-	static const struct acpi_device_id i2c_multi_instantiate_ids[] = {
 		{"BSG1160", },
 		{"BSG2150", },
+		{"CSC3551", },
 		{"INT33FE", },
 		{"INT3515", },
+		/* Non-conforming _HID for Cirrus Logic already released */
+		{"CLSA0100", },
+	/*
+	 * HIDs of device with an UartSerialBusV2 resource for which userspace
+	 * expects a regular tty cdev to be created (instead of the in kernel
+	 * serdev) and which have a kernel driver which expects a platform_dev
+	 * such as the rfkill-gpio driver.
+	 */
+		{"BCM4752", },
+		{"LNV4752", },
 		{}
 	};
 
@@ -1716,8 +1725,7 @@
 	     fwnode_property_present(&device->fwnode, "baud")))
 		return true;
 
-	/* Instantiate a pdev for the i2c-multi-instantiate drv to bind to */
-	if (!acpi_match_device_ids(device, i2c_multi_instantiate_ids))
+	if (!acpi_match_device_ids(device, ignore_serial_bus_ids))
 		return false;
 
 	INIT_LIST_HEAD(&resource_list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/sleep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/sleep.c
@@ -361,6 +361,14 @@
 		DMI_MATCH(DMI_PRODUCT_NAME, "80E3"),
 		},
 	},
+	{
+	.callback = init_nvs_save_s3,
+	.ident = "Lenovo G40-45",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "80E1"),
+		},
+	},
 	/*
 	 * ThinkPad X1 Tablet(2016) cannot do suspend-to-idle using
 	 * the Low Power S0 Idle firmware interface (see
@@ -615,11 +623,19 @@
 	}
 
 	/*
-	 * Disable and clear GPE status before interrupt is enabled. Some GPEs
-	 * (like wakeup GPE) haven't handler, this can avoid such GPE misfire.
-	 * acpi_leave_sleep_state will reenable specific GPEs later
+	 * Disable all GPE and clear their status bits before interrupts are
+	 * enabled. Some GPEs (like wakeup GPEs) have no handlers and this can
+	 * prevent them from producing spurious interrups.
+	 *
+	 * acpi_leave_sleep_state() will reenable specific GPEs later.
+	 *
+	 * Because this code runs on one CPU with disabled interrupts (all of
+	 * the other CPUs are offline at this time), it need not acquire any
+	 * sleeping locks which may trigger an implicit preemption point even
+	 * if there is no contention, so avoid doing that by using a low-level
+	 * library routine here.
 	 */
-	acpi_disable_all_gpes();
+	acpi_hw_disable_all_gpes();
 	/* Allow EC transactions to happen. */
 	acpi_ec_unblock_transactions();
 
@@ -767,6 +783,7 @@
 			return true;
 		}
 
+		pm_wakeup_clear(acpi_sci_irq);
 		rearm_wake_irq(acpi_sci_irq);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/sysfs.c
@@ -415,19 +415,30 @@
 			      loff_t offset, size_t count)
 {
 	struct acpi_data_attr *data_attr;
-	void *base;
-	ssize_t rc;
+	void __iomem *base;
+	ssize_t size;
 
 	data_attr = container_of(bin_attr, struct acpi_data_attr, attr);
+	size = data_attr->attr.size;
 
-	base = acpi_os_map_memory(data_attr->addr, data_attr->attr.size);
+	if (offset < 0)
+		return -EINVAL;
+
+	if (offset >= size)
+		return 0;
+
+	if (count > size - offset)
+		count = size - offset;
+
+	base = acpi_os_map_iomem(data_attr->addr, size);
 	if (!base)
 		return -ENOMEM;
-	rc = memory_read_from_buffer(buf, count, &offset, base,
-				     data_attr->attr.size);
-	acpi_os_unmap_memory(base, data_attr->attr.size);
 
-	return rc;
+	memcpy_fromio(buf, base + offset, count);
+
+	acpi_os_unmap_iomem(base, size);
+
+	return count;
 }
 
 static int acpi_bert_data_init(void *th, struct acpi_data_attr *data_attr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/thermal.c
@@ -59,10 +59,6 @@
 module_param(tzp, int, 0444);
 MODULE_PARM_DESC(tzp, "Thermal zone polling frequency, in 1/10 seconds.");
 
-static int nocrt;
-module_param(nocrt, int, 0);
-MODULE_PARM_DESC(nocrt, "Set to take no action upon ACPI thermal zone critical trips points.");
-
 static int off;
 module_param(off, int, 0);
 MODULE_PARM_DESC(off, "Set to disable ACPI thermal support.");
@@ -1098,8 +1094,6 @@
 		return -EINVAL;
 
 	for (i = 0; i < ACPI_THERMAL_MAX_ACTIVE; i++) {
-		if (!(&tz->trips.active[i]))
-			break;
 		if (!tz->trips.active[i].flags.valid)
 			break;
 		tz->trips.active[i].flags.enabled = 1;
@@ -1134,7 +1128,7 @@
 
 	pr_notice("%s detected: disabling all critical thermal trip point actions.\n",
 		  d->ident);
-	nocrt = 1;
+	crt = -1;
 	return 0;
 }
 static int thermal_tzp(const struct dmi_system_id *d) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/video_detect.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/video_detect.c
@@ -308,12 +308,21 @@
 		},
 	},
 	{
+	 /* https://bugzilla.suse.com/show_bug.cgi?id=1208724 */
+	 .callback = video_detect_force_native,
+	 /* Lenovo Ideapad Z470 */
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		DMI_MATCH(DMI_PRODUCT_VERSION, "IdeaPad Z470"),
+		},
+	},
+	{
 	 /* https://bugzilla.redhat.com/show_bug.cgi?id=1187004 */
 	 .callback = video_detect_force_native,
 	 .ident = "Lenovo Ideapad Z570",
 	 .matches = {
 		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
-		DMI_MATCH(DMI_PRODUCT_NAME, "102434U"),
+		DMI_MATCH(DMI_PRODUCT_VERSION, "Ideapad Z570"),
 		},
 	},
 	{
@@ -333,6 +342,48 @@
 		},
 	},
 	{
+	 .callback = video_detect_force_native,
+	 /* Lenovo Slim 7 16ARH7 */
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "82UX"),
+		},
+	},
+	{
+	 .callback = video_detect_force_native,
+	 /* Lenovo ThinkPad X131e (3371 AMD version) */
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "3371"),
+		},
+	},
+	{
+	 .callback = video_detect_force_native,
+	 /* Apple iMac11,3 */
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+		DMI_MATCH(DMI_PRODUCT_NAME, "iMac11,3"),
+		},
+	},
+	{
+	 /* https://gitlab.freedesktop.org/drm/amd/-/issues/1838 */
+	 .callback = video_detect_force_native,
+	 /* Apple iMac12,1 */
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+		DMI_MATCH(DMI_PRODUCT_NAME, "iMac12,1"),
+		},
+	},
+	{
+	 /* https://gitlab.freedesktop.org/drm/amd/-/issues/2753 */
+	 .callback = video_detect_force_native,
+	 /* Apple iMac12,2 */
+	 .matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+		DMI_MATCH(DMI_PRODUCT_NAME, "iMac12,2"),
+		},
+	},
+	{
 	 /* https://bugzilla.redhat.com/show_bug.cgi?id=1217249 */
 	 .callback = video_detect_force_native,
 	 .ident = "Apple MacBook Pro 12,1",
@@ -409,7 +460,161 @@
 		DMI_MATCH(DMI_PRODUCT_NAME, "GA503"),
 		},
 	},
-
+	/*
+	 * Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a
+	 * working native and video interface. However the default detection
+	 * mechanism first registers the video interface before unregistering
+	 * it again and switching to the native interface during boot. This
+	 * results in a dangling SBIOS request for backlight change for some
+	 * reason, causing the backlight to switch to ~2% once per boot on the
+	 * first power cord connect or disconnect event. Setting the native
+	 * interface explicitly circumvents this buggy behaviour, by avoiding
+	 * the unregistering process.
+	 */
+	{
+	.callback = video_detect_force_native,
+	.ident = "Clevo NL5xRU",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "NL5xRU"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "Clevo NL5xRU",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "AURA1501"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "Clevo NL5xRU",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "EDUBOOK1502"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "Clevo NL5xNU",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "NL5xNU"),
+		},
+	},
+	/*
+	 * The TongFang PF5PU1G, PF4NU1F, PF5NU1G, and PF5LUXG/TUXEDO BA15 Gen10,
+	 * Pulse 14/15 Gen1, and Pulse 15 Gen2 have the same problem as the Clevo
+	 * NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2. See the description
+	 * above.
+	 */
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang PF5PU1G",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "PF5PU1G"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang PF4NU1F",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "PF4NU1F"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang PF4NU1F",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "PULSE1401"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang PF5NU1G",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "PF5NU1G"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang PF5NU1G",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "PULSE1501"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang PF5LUXG",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "PF5LUXG"),
+		},
+	},
+	/*
+	 * More Tongfang devices with the same issue as the Clevo NL5xRU and
+	 * NL5xNU/TUXEDO Aura 15 Gen1 and Gen2. See the description above.
+	 */
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GKxNRxx",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "GKxNRxx"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GKxNRxx",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "POLARIS1501A1650TI"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GKxNRxx",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "POLARIS1501A2060"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GKxNRxx",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "POLARIS1701A1650TI"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GKxNRxx",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "TUXEDO"),
+		DMI_MATCH(DMI_BOARD_NAME, "POLARIS1701A2060"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GMxNGxx",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "GMxNGxx"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GMxZGxx",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "GMxZGxx"),
+		},
+	},
+	{
+	.callback = video_detect_force_native,
+	.ident = "TongFang GMxRGxx",
+	.matches = {
+		DMI_MATCH(DMI_BOARD_NAME, "GMxRGxx"),
+		},
+	},
 	/*
 	 * Desktops which falsely report a backlight and which our heuristics
 	 * for this do not catch.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/viot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/viot.c
@@ -249,6 +249,26 @@
 }
 
 /**
+ * acpi_viot_early_init - Test the presence of VIOT and enable ACS
+ *
+ * If the VIOT does exist, ACS must be enabled. This cannot be
+ * done in acpi_viot_init() which is called after the bus scan
+ */
+void __init acpi_viot_early_init(void)
+{
+#ifdef CONFIG_PCI
+	acpi_status status;
+	struct acpi_table_header *hdr;
+
+	status = acpi_get_table(ACPI_SIG_VIOT, 0, &hdr);
+	if (ACPI_FAILURE(status))
+		return;
+	pci_request_acs();
+	acpi_put_table(hdr);
+#endif
+}
+
+/**
  * acpi_viot_init - Parse the VIOT table
  *
  * Parse the VIOT table, prepare the list of endpoints to be used during DMA
@@ -309,6 +329,7 @@
 {
 	u32 epid;
 	struct viot_endpoint *ep;
+	struct device *aliased_dev = data;
 	u32 domain_nr = pci_domain_nr(pdev->bus);
 
 	list_for_each_entry(ep, &viot_pci_ranges, list) {
@@ -319,13 +340,7 @@
 			epid = ((domain_nr - ep->segment_start) << 16) +
 				dev_id - ep->bdf_start + ep->endpoint_id;
 
-			/*
-			 * If we found a PCI range managed by the viommu, we're
-			 * the one that has to request ACS.
-			 */
-			pci_request_acs();
-
-			return viot_dev_iommu_init(&pdev->dev, ep->viommu,
+			return viot_dev_iommu_init(aliased_dev, ep->viommu,
 						   epid);
 		}
 	}
@@ -359,7 +374,7 @@
 {
 	if (dev_is_pci(dev))
 		return pci_for_each_dma_alias(to_pci_dev(dev),
-					      viot_pci_dev_iommu_init, NULL);
+					      viot_pci_dev_iommu_init, dev);
 	else if (dev_is_platform(dev))
 		return viot_mmio_dev_iommu_init(to_platform_device(dev));
 	return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/x86/s2idle.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/x86/s2idle.c
@@ -86,6 +86,8 @@
 	int min_dstate;
 };
 
+static LIST_HEAD(lps0_s2idle_devops_head);
+
 static struct lpi_constraints *lpi_constraints_table;
 static int lpi_constraints_table_size;
 static int rev_id;
@@ -109,6 +111,12 @@
 		union acpi_object *package = &out_obj->package.elements[i];
 
 		if (package->type == ACPI_TYPE_PACKAGE) {
+			if (lpi_constraints_table) {
+				acpi_handle_err(lps0_device_handle,
+						"Duplicate constraints list\n");
+				goto free_acpi_buffer;
+			}
+
 			lpi_constraints_table = kcalloc(package->package.count,
 							sizeof(*lpi_constraints_table),
 							GFP_KERNEL);
@@ -119,17 +127,16 @@
 			acpi_handle_debug(lps0_device_handle,
 					  "LPI: constraints list begin:\n");
 
-			for (j = 0; j < package->package.count; ++j) {
+			for (j = 0; j < package->package.count; j++) {
 				union acpi_object *info_obj = &package->package.elements[j];
 				struct lpi_device_constraint_amd dev_info = {};
 				struct lpi_constraints *list;
 				acpi_status status;
 
-				for (k = 0; k < info_obj->package.count; ++k) {
-					union acpi_object *obj = &info_obj->package.elements[k];
+				list = &lpi_constraints_table[lpi_constraints_table_size];
 
-					list = &lpi_constraints_table[lpi_constraints_table_size];
-					list->min_dstate = -1;
+				for (k = 0; k < info_obj->package.count; k++) {
+					union acpi_object *obj = &info_obj->package.elements[k];
 
 					switch (k) {
 					case 0:
@@ -145,27 +152,21 @@
 						dev_info.min_dstate = obj->integer.value;
 						break;
 					}
-
-					if (!dev_info.enabled || !dev_info.name ||
-					    !dev_info.min_dstate)
-						continue;
-
-					status = acpi_get_handle(NULL, dev_info.name,
-								 &list->handle);
-					if (ACPI_FAILURE(status))
-						continue;
-
-					acpi_handle_debug(lps0_device_handle,
-							  "Name:%s\n", dev_info.name);
-
-					list->min_dstate = dev_info.min_dstate;
-
-					if (list->min_dstate < 0) {
-						acpi_handle_debug(lps0_device_handle,
-								  "Incomplete constraint defined\n");
-						continue;
-					}
 				}
+
+				if (!dev_info.enabled || !dev_info.name ||
+				    !dev_info.min_dstate)
+					continue;
+
+				status = acpi_get_handle(NULL, dev_info.name, &list->handle);
+				if (ACPI_FAILURE(status))
+					continue;
+
+				acpi_handle_debug(lps0_device_handle,
+						  "Name:%s\n", dev_info.name);
+
+				list->min_dstate = dev_info.min_dstate;
+
 				lpi_constraints_table_size++;
 			}
 		}
@@ -210,7 +211,7 @@
 		if (!package)
 			continue;
 
-		for (j = 0; j < package->package.count; ++j) {
+		for (j = 0; j < package->package.count; j++) {
 			union acpi_object *element =
 					&(package->package.elements[j]);
 
@@ -242,7 +243,7 @@
 
 		constraint->min_dstate = -1;
 
-		for (j = 0; j < package_count; ++j) {
+		for (j = 0; j < package_count; j++) {
 			union acpi_object *info_obj = &info.package[j];
 			union acpi_object *cnstr_pkg;
 			union acpi_object *obj;
@@ -378,16 +379,13 @@
 		 * AMDI0006:
 		 * - should use rev_id 0x0
 		 * - function mask = 0x3: Should use Microsoft method
-		 * AMDI0007:
-		 * - Should use rev_id 0x2
-		 * - Should only use AMD method
 		 */
 		const char *hid = acpi_device_hid(adev);
-		rev_id = strcmp(hid, "AMDI0007") ? 0 : 2;
+		rev_id = 0;
 		lps0_dsm_func_mask = validate_dsm(adev->handle,
 					ACPI_LPS0_DSM_UUID_AMD, rev_id, &lps0_dsm_guid);
 		lps0_dsm_func_mask_microsoft = validate_dsm(adev->handle,
-					ACPI_LPS0_DSM_UUID_MICROSOFT, 0,
+					ACPI_LPS0_DSM_UUID_MICROSOFT, rev_id,
 					&lps0_dsm_guid_microsoft);
 		if (lps0_dsm_func_mask > 0x3 && (!strcmp(hid, "AMD0004") ||
 						 !strcmp(hid, "AMD0005") ||
@@ -395,9 +393,6 @@
 			lps0_dsm_func_mask = (lps0_dsm_func_mask << 1) | 0x1;
 			acpi_handle_debug(adev->handle, "_DSM UUID %s: Adjusted function mask: 0x%x\n",
 					  ACPI_LPS0_DSM_UUID_AMD, lps0_dsm_func_mask);
-		} else if (lps0_dsm_func_mask_microsoft > 0 && !strcmp(hid, "AMDI0007")) {
-			lps0_dsm_func_mask_microsoft = -EINVAL;
-			acpi_handle_debug(adev->handle, "_DSM Using AMD method\n");
 		}
 	} else {
 		rev_id = 1;
@@ -424,15 +419,11 @@
 		mem_sleep_current = PM_SUSPEND_TO_IDLE;
 
 	/*
-	 * Some Intel based LPS0 systems, like ASUS Zenbook UX430UNR/i7-8550U don't
-	 * use intel-hid or intel-vbtn but require the EC GPE to be enabled while
-	 * suspended for certain wakeup devices to work, so mark it as wakeup-capable.
-	 *
-	 * Only enable on !AMD as enabling this universally causes problems for a number
-	 * of AMD based systems.
+	 * Some LPS0 systems, like ASUS Zenbook UX430UNR/i7-8550U, require the
+	 * EC GPE to be enabled while suspended for certain wakeup devices to
+	 * work, so mark it as wakeup-capable.
 	 */
-	if (!acpi_s2idle_vendor_amd())
-		acpi_ec_mark_gpe_for_wake();
+	acpi_ec_mark_gpe_for_wake();
 
 	return 0;
 }
@@ -444,6 +435,8 @@
 
 int acpi_s2idle_prepare_late(void)
 {
+	struct acpi_s2idle_dev_ops *handler;
+
 	if (!lps0_device_handle || sleep_no_lps0)
 		return 0;
 
@@ -474,14 +467,26 @@
 		acpi_sleep_run_lps0_dsm(ACPI_LPS0_MS_ENTRY,
 				lps0_dsm_func_mask_microsoft, lps0_dsm_guid_microsoft);
 	}
+
+	list_for_each_entry(handler, &lps0_s2idle_devops_head, list_node) {
+		if (handler->prepare)
+			handler->prepare();
+	}
+
 	return 0;
 }
 
 void acpi_s2idle_restore_early(void)
 {
+	struct acpi_s2idle_dev_ops *handler;
+
 	if (!lps0_device_handle || sleep_no_lps0)
 		return;
 
+	list_for_each_entry(handler, &lps0_s2idle_devops_head, list_node)
+		if (handler->restore)
+			handler->restore();
+
 	/* Modern standby exit */
 	if (lps0_dsm_func_mask_microsoft > 0)
 		acpi_sleep_run_lps0_dsm(ACPI_LPS0_MS_EXIT,
@@ -524,4 +529,28 @@
 	s2idle_set_ops(&acpi_s2idle_ops_lps0);
 }
 
+int acpi_register_lps0_dev(struct acpi_s2idle_dev_ops *arg)
+{
+	if (!lps0_device_handle || sleep_no_lps0)
+		return -ENODEV;
+
+	lock_system_sleep();
+	list_add(&arg->list_node, &lps0_s2idle_devops_head);
+	unlock_system_sleep();
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(acpi_register_lps0_dev);
+
+void acpi_unregister_lps0_dev(struct acpi_s2idle_dev_ops *arg)
+{
+	if (!lps0_device_handle || sleep_no_lps0)
+		return;
+
+	lock_system_sleep();
+	list_del(&arg->list_node);
+	unlock_system_sleep();
+}
+EXPORT_SYMBOL_GPL(acpi_unregister_lps0_dev);
+
 #endif /* CONFIG_SUSPEND */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/acpi/x86/utils.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/acpi/x86/utils.c
@@ -22,58 +22,71 @@
  * Some BIOS-es (temporarily) hide specific APCI devices to work around Windows
  * driver bugs. We use DMI matching to match known cases of this.
  *
- * We work around this by always reporting ACPI_STA_DEFAULT for these
- * devices. Note this MUST only be done for devices where this is safe.
+ * Likewise sometimes some not-actually present devices are sometimes
+ * reported as present, which may cause issues.
  *
- * This forcing of devices to be present is limited to specific CPU (SoC)
- * models both to avoid potentially causing trouble on other models and
- * because some HIDs are re-used on different SoCs for completely
- * different devices.
+ * We work around this by using the below quirk list to override the status
+ * reported by the _STA method with a fixed value (ACPI_STA_DEFAULT or 0).
+ * Note this MUST only be done for devices where this is safe.
+ *
+ * This status overriding is limited to specific CPU (SoC) models both to
+ * avoid potentially causing trouble on other models and because some HIDs
+ * are re-used on different SoCs for completely different devices.
  */
-struct always_present_id {
+struct override_status_id {
 	struct acpi_device_id hid[2];
 	struct x86_cpu_id cpu_ids[2];
 	struct dmi_system_id dmi_ids[2]; /* Optional */
 	const char *uid;
+	const char *path;
+	unsigned long long status;
 };
 
-#define X86_MATCH(model)	X86_MATCH_INTEL_FAM6_MODEL(model, NULL)
-
-#define ENTRY(hid, uid, cpu_models, dmi...) {				\
+#define ENTRY(status, hid, uid, path, cpu_model, dmi...) {		\
 	{ { hid, }, {} },						\
-	{ cpu_models, {} },						\
+	{ X86_MATCH_INTEL_FAM6_MODEL(cpu_model, NULL), {} },		\
 	{ { .matches = dmi }, {} },					\
 	uid,								\
+	path,								\
+	status,								\
 }
 
-static const struct always_present_id always_present_ids[] = {
+#define PRESENT_ENTRY_HID(hid, uid, cpu_model, dmi...) \
+	ENTRY(ACPI_STA_DEFAULT, hid, uid, NULL, cpu_model, dmi)
+
+#define NOT_PRESENT_ENTRY_HID(hid, uid, cpu_model, dmi...) \
+	ENTRY(0, hid, uid, NULL, cpu_model, dmi)
+
+#define PRESENT_ENTRY_PATH(path, cpu_model, dmi...) \
+	ENTRY(ACPI_STA_DEFAULT, "", NULL, path, cpu_model, dmi)
+
+#define NOT_PRESENT_ENTRY_PATH(path, cpu_model, dmi...) \
+	ENTRY(0, "", NULL, path, cpu_model, dmi)
+
+static const struct override_status_id override_status_ids[] = {
 	/*
 	 * Bay / Cherry Trail PWM directly poked by GPU driver in win10,
 	 * but Linux uses a separate PWM driver, harmless if not used.
 	 */
-	ENTRY("80860F09", "1", X86_MATCH(ATOM_SILVERMONT), {}),
-	ENTRY("80862288", "1", X86_MATCH(ATOM_AIRMONT), {}),
+	PRESENT_ENTRY_HID("80860F09", "1", ATOM_SILVERMONT, {}),
+	PRESENT_ENTRY_HID("80862288", "1", ATOM_AIRMONT, {}),
 
-	/* Lenovo Yoga Book uses PWM2 for keyboard backlight control */
-	ENTRY("80862289", "2", X86_MATCH(ATOM_AIRMONT), {
-			DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X9"),
-		}),
 	/*
 	 * The INT0002 device is necessary to clear wakeup interrupt sources
 	 * on Cherry Trail devices, without it we get nobody cared IRQ msgs.
 	 */
-	ENTRY("INT0002", "1", X86_MATCH(ATOM_AIRMONT), {}),
+	PRESENT_ENTRY_HID("INT0002", "1", ATOM_AIRMONT, {}),
 	/*
 	 * On the Dell Venue 11 Pro 7130 and 7139, the DSDT hides
 	 * the touchscreen ACPI device until a certain time
 	 * after _SB.PCI0.GFX0.LCD.LCD1._ON gets called has passed
 	 * *and* _STA has been called at least 3 times since.
 	 */
-	ENTRY("SYNA7500", "1", X86_MATCH(HASWELL_L), {
+	PRESENT_ENTRY_HID("SYNA7500", "1", HASWELL_L, {
 		DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
 		DMI_MATCH(DMI_PRODUCT_NAME, "Venue 11 Pro 7130"),
 	      }),
-	ENTRY("SYNA7500", "1", X86_MATCH(HASWELL_L), {
+	PRESENT_ENTRY_HID("SYNA7500", "1", HASWELL_L, {
 		DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
 		DMI_MATCH(DMI_PRODUCT_NAME, "Venue 11 Pro 7139"),
 	      }),
@@ -81,54 +94,83 @@
 	/*
 	 * The GPD win BIOS dated 20170221 has disabled the accelerometer, the
 	 * drivers sometimes cause crashes under Windows and this is how the
-	 * manufacturer has solved this :| Note that the the DMI data is less
-	 * generic then it seems, a board_vendor of "AMI Corporation" is quite
-	 * rare and a board_name of "Default String" also is rare.
+	 * manufacturer has solved this :|  The DMI match may not seem unique,
+	 * but it is. In the 67000+ DMI decode dumps from linux-hardware.org
+	 * only 116 have board_vendor set to "AMI Corporation" and of those 116
+	 * only the GPD win and pocket entries' board_name is "Default string".
 	 *
 	 * Unfortunately the GPD pocket also uses these strings and its BIOS
 	 * was copy-pasted from the GPD win, so it has a disabled KIOX000A
 	 * node which we should not enable, thus we also check the BIOS date.
 	 */
-	ENTRY("KIOX000A", "1", X86_MATCH(ATOM_AIRMONT), {
+	PRESENT_ENTRY_HID("KIOX000A", "1", ATOM_AIRMONT, {
 		DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
 		DMI_MATCH(DMI_BOARD_NAME, "Default string"),
 		DMI_MATCH(DMI_PRODUCT_NAME, "Default string"),
 		DMI_MATCH(DMI_BIOS_DATE, "02/21/2017")
 	      }),
-	ENTRY("KIOX000A", "1", X86_MATCH(ATOM_AIRMONT), {
+	PRESENT_ENTRY_HID("KIOX000A", "1", ATOM_AIRMONT, {
 		DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
 		DMI_MATCH(DMI_BOARD_NAME, "Default string"),
 		DMI_MATCH(DMI_PRODUCT_NAME, "Default string"),
 		DMI_MATCH(DMI_BIOS_DATE, "03/20/2017")
 	      }),
-	ENTRY("KIOX000A", "1", X86_MATCH(ATOM_AIRMONT), {
+	PRESENT_ENTRY_HID("KIOX000A", "1", ATOM_AIRMONT, {
 		DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
 		DMI_MATCH(DMI_BOARD_NAME, "Default string"),
 		DMI_MATCH(DMI_PRODUCT_NAME, "Default string"),
 		DMI_MATCH(DMI_BIOS_DATE, "05/25/2017")
 	      }),
+
+	/*
+	 * The GPD win/pocket have a PCI wifi card, but its DSDT has the SDIO
+	 * mmc controller enabled and that has a child-device which _PS3
+	 * method sets a GPIO causing the PCI wifi card to turn off.
+	 * See above remark about uniqueness of the DMI match.
+	 */
+	NOT_PRESENT_ENTRY_PATH("\\_SB_.PCI0.SDHB.BRC1", ATOM_AIRMONT, {
+		DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
+		DMI_EXACT_MATCH(DMI_BOARD_NAME, "Default string"),
+		DMI_EXACT_MATCH(DMI_BOARD_SERIAL, "Default string"),
+		DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Default string"),
+	      }),
 };
 
-bool acpi_device_always_present(struct acpi_device *adev)
+bool acpi_device_override_status(struct acpi_device *adev, unsigned long long *status)
 {
 	bool ret = false;
 	unsigned int i;
 
-	for (i = 0; i < ARRAY_SIZE(always_present_ids); i++) {
-		if (acpi_match_device_ids(adev, always_present_ids[i].hid))
-			continue;
-
-		if (!adev->pnp.unique_id ||
-		    strcmp(adev->pnp.unique_id, always_present_ids[i].uid))
+	for (i = 0; i < ARRAY_SIZE(override_status_ids); i++) {
+		if (!x86_match_cpu(override_status_ids[i].cpu_ids))
 			continue;
 
-		if (!x86_match_cpu(always_present_ids[i].cpu_ids))
+		if (override_status_ids[i].dmi_ids[0].matches[0].slot &&
+		    !dmi_check_system(override_status_ids[i].dmi_ids))
 			continue;
 
-		if (always_present_ids[i].dmi_ids[0].matches[0].slot &&
-		    !dmi_check_system(always_present_ids[i].dmi_ids))
-			continue;
+		if (override_status_ids[i].path) {
+			struct acpi_buffer path = { ACPI_ALLOCATE_BUFFER, NULL };
+			bool match;
+
+			if (acpi_get_name(adev->handle, ACPI_FULL_PATHNAME, &path))
+				continue;
+
+			match = strcmp((char *)path.pointer, override_status_ids[i].path) == 0;
+			kfree(path.pointer);
+
+			if (!match)
+				continue;
+		} else {
+			if (acpi_match_device_ids(adev, override_status_ids[i].hid))
+				continue;
+
+			if (!adev->pnp.unique_id ||
+			    strcmp(adev->pnp.unique_id, override_status_ids[i].uid))
+				continue;
+		}
 
+		*status = override_status_ids[i].status;
 		ret = true;
 		break;
 	}
@@ -137,26 +179,35 @@
 }
 
 /*
- * AMD systems from Renoir and Lucienne *require* that the NVME controller
+ * AMD systems from Renoir onwards *require* that the NVME controller
  * is put into D3 over a Modern Standby / suspend-to-idle cycle.
  *
  * This is "typically" accomplished using the `StorageD3Enable`
  * property in the _DSD that is checked via the `acpi_storage_d3` function
- * but this property was introduced after many of these systems launched
- * and most OEM systems don't have it in their BIOS.
+ * but some OEM systems still don't have it in their BIOS.
  *
  * The Microsoft documentation for StorageD3Enable mentioned that Windows has
- * a hardcoded allowlist for D3 support, which was used for these platforms.
+ * a hardcoded allowlist for D3 support as well as a registry key to override
+ * the BIOS, which has been used for these cases.
  *
  * This allows quirking on Linux in a similar fashion.
+ *
+ * Cezanne systems shouldn't *normally* need this as the BIOS includes
+ * StorageD3Enable.  But for two reasons we have added it.
+ * 1) The BIOS on a number of Dell systems have ambiguity
+ *    between the same value used for _ADR on ACPI nodes GPP1.DEV0 and GPP1.NVME.
+ *    GPP1.NVME is needed to get StorageD3Enable node set properly.
+ *    https://bugzilla.kernel.org/show_bug.cgi?id=216440
+ *    https://bugzilla.kernel.org/show_bug.cgi?id=216773
+ *    https://bugzilla.kernel.org/show_bug.cgi?id=217003
+ * 2) On at least one HP system StorageD3Enable is missing on the second NVME
+ *    disk in the system.
+ * 3) On at least one HP Rembrandt system StorageD3Enable is missing on the only
+ *    NVME device.
  */
-static const struct x86_cpu_id storage_d3_cpu_ids[] = {
-	X86_MATCH_VENDOR_FAM_MODEL(AMD, 23, 96, NULL),	/* Renoir */
-	X86_MATCH_VENDOR_FAM_MODEL(AMD, 23, 104, NULL),	/* Lucienne */
-	{}
-};
-
 bool force_storage_d3(void)
 {
-	return x86_match_cpu(storage_d3_cpu_ids);
+	if (!cpu_feature_enabled(X86_FEATURE_ZEN))
+		return false;
+	return acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/amba/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/amba/bus.c
@@ -366,6 +366,7 @@
 {
 	struct amba_device *d = to_amba_device(dev);
 
+	of_node_put(d->dev.of_node);
 	if (d->res.parent)
 		release_resource(&d->res);
 	kfree(d);
@@ -377,9 +378,6 @@
 	void __iomem *tmp;
 	int i, ret;
 
-	WARN_ON(dev->irq[0] == (unsigned int)-1);
-	WARN_ON(dev->irq[1] == (unsigned int)-1);
-
 	ret = request_resource(parent, &dev->res);
 	if (ret)
 		goto err_out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/Kconfig
@@ -9,7 +9,7 @@
 if ANDROID
 
 config ANDROID_BINDER_IPC
-	bool "Android Binder IPC Driver"
+	tristate "Android Binder IPC Driver"
 	depends on MMU
 	default n
 	help
@@ -21,8 +21,8 @@
 	  between said processes.
 
 config ANDROID_BINDERFS
-	bool "Android Binderfs filesystem"
-	depends on ANDROID_BINDER_IPC
+	tristate "Android Binderfs filesystem"
+	depends on (ANDROID_BINDER_IPC=y) || (ANDROID_BINDER_IPC=m && m)
 	default n
 	help
 	  Binderfs is a pseudo-filesystem for the Android Binder IPC driver
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/Makefile
@@ -1,6 +1,10 @@
 # SPDX-License-Identifier: GPL-2.0-only
 ccflags-y += -I$(src)			# needed for trace events
 
-obj-$(CONFIG_ANDROID_BINDERFS)		+= binderfs.o
-obj-$(CONFIG_ANDROID_BINDER_IPC)	+= binder.o binder_alloc.o
-obj-$(CONFIG_ANDROID_BINDER_IPC_SELFTEST) += binder_alloc_selftest.o
+binder_linux-y := binder.o binder_alloc.o
+obj-$(CONFIG_ANDROID_BINDER_IPC) += binder_linux.o
+binder_linux-$(CONFIG_ANDROID_BINDERFS) += binderfs.o
+binder_linux-$(CONFIG_ANDROID_BINDER_IPC_SELFTEST) += binder_alloc_selftest.o
+
+# binder-$(CONFIG_ANDROID_BINDER_IPC) := binder.o binder_alloc.o
+# binder-$(CONFIG_ANDROID_BINDERFS) += binderfs.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/binder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/binder.c
@@ -170,8 +170,32 @@
 	atomic_inc(&binder_stats.obj_created[type]);
 }
 
-struct binder_transaction_log binder_transaction_log;
-struct binder_transaction_log binder_transaction_log_failed;
+struct binder_transaction_log_entry {
+	int debug_id;
+	int debug_id_done;
+	int call_type;
+	int from_proc;
+	int from_thread;
+	int target_handle;
+	int to_proc;
+	int to_thread;
+	int to_node;
+	int data_size;
+	int offsets_size;
+	int return_error_line;
+	uint32_t return_error;
+	uint32_t return_error_param;
+	char context_name[BINDERFS_MAX_NAME + 1];
+};
+
+struct binder_transaction_log {
+	atomic_t cur;
+	bool full;
+	struct binder_transaction_log_entry entry[32];
+};
+
+static struct binder_transaction_log binder_transaction_log;
+static struct binder_transaction_log binder_transaction_log_failed;
 
 static struct binder_transaction_log_entry *binder_transaction_log_add(
 	struct binder_transaction_log *log)
@@ -426,6 +450,16 @@
 {
 	WARN_ON(!list_empty(&thread->waiting_thread_node));
 	binder_enqueue_work_ilocked(work, &thread->todo);
+
+	/* (e)poll-based threads require an explicit wakeup signal when
+	 * queuing their own work; they rely on these events to consume
+	 * messages without I/O block. Without it, threads risk waiting
+	 * indefinitely without handling the work.
+	 */
+	if (thread->looper & BINDER_LOOPER_STATE_POLL &&
+	    thread->pid == current->pid && !thread->process_todo)
+		wake_up_interruptible_sync(&thread->wait);
+
 	thread->process_todo = true;
 }
 
@@ -508,9 +542,7 @@
 static bool binder_available_for_proc_work_ilocked(struct binder_thread *thread)
 {
 	return !thread->transaction_stack &&
-		binder_worklist_empty_ilocked(&thread->todo) &&
-		(thread->looper & (BINDER_LOOPER_STATE_ENTERED |
-				   BINDER_LOOPER_STATE_REGISTERED));
+		binder_worklist_empty_ilocked(&thread->todo);
 }
 
 static void binder_wakeup_poll_threads_ilocked(struct binder_proc *proc,
@@ -1334,6 +1366,18 @@
 	}
 	ret = binder_inc_ref_olocked(ref, strong, target_list);
 	*rdata = ref->data;
+	if (ret && ref == new_ref) {
+		/*
+		 * Cleanup the failed reference here as the target
+		 * could now be dead and have already released its
+		 * references by now. Calling on the new reference
+		 * with strong=0 and a tmp_refs will not decrement
+		 * the node. The new_ref gets kfree'd below.
+		 */
+		binder_cleanup_ref_olocked(new_ref);
+		ref = NULL;
+	}
+
 	binder_proc_unlock(proc);
 	if (new_ref && ref != new_ref)
 		/*
@@ -1608,15 +1652,21 @@
 /**
  * binder_get_object() - gets object and checks for valid metadata
  * @proc:	binder_proc owning the buffer
+ * @u:		sender's user pointer to base of buffer
  * @buffer:	binder_buffer that we're parsing.
  * @offset:	offset in the @buffer at which to validate an object.
  * @object:	struct binder_object to read into
  *
- * Return:	If there's a valid metadata object at @offset in @buffer, the
+ * Copy the binder object at the given offset into @object. If @u is
+ * provided then the copy is from the sender's buffer. If not, then
+ * it is copied from the target's @buffer.
+ *
+ * Return:	If there's a valid metadata object at @offset, the
  *		size of that object. Otherwise, it returns zero. The object
  *		is read into the struct binder_object pointed to by @object.
  */
 static size_t binder_get_object(struct binder_proc *proc,
+				const void __user *u,
 				struct binder_buffer *buffer,
 				unsigned long offset,
 				struct binder_object *object)
@@ -1627,10 +1677,18 @@
 
 	read_size = min_t(size_t, sizeof(*object), buffer->data_size - offset);
 	if (offset > buffer->data_size || read_size < sizeof(*hdr) ||
-	    binder_alloc_copy_from_buffer(&proc->alloc, object, buffer,
-					  offset, read_size))
+	    !IS_ALIGNED(offset, sizeof(u32)))
 		return 0;
 
+	if (u) {
+		if (copy_from_user(object, u + offset, read_size))
+			return 0;
+	} else {
+		if (binder_alloc_copy_from_buffer(&proc->alloc, object, buffer,
+						  offset, read_size))
+			return 0;
+	}
+
 	/* Ok, now see if we read a complete object. */
 	hdr = &object->hdr;
 	switch (hdr->type) {
@@ -1702,7 +1760,7 @@
 					  b, buffer_offset,
 					  sizeof(object_offset)))
 		return NULL;
-	object_size = binder_get_object(proc, b, object_offset, object);
+	object_size = binder_get_object(proc, NULL, b, object_offset, object);
 	if (!object_size || object->hdr.type != BINDER_TYPE_PTR)
 		return NULL;
 	if (object_offsetp)
@@ -1767,7 +1825,8 @@
 		unsigned long buffer_offset;
 		struct binder_object last_object;
 		struct binder_buffer_object *last_bbo;
-		size_t object_size = binder_get_object(proc, b, last_obj_offset,
+		size_t object_size = binder_get_object(proc, NULL, b,
+						       last_obj_offset,
 						       &last_object);
 		if (object_size != sizeof(*last_bbo))
 			return false;
@@ -1854,24 +1913,23 @@
 static void binder_transaction_buffer_release(struct binder_proc *proc,
 					      struct binder_thread *thread,
 					      struct binder_buffer *buffer,
-					      binder_size_t failed_at,
+					      binder_size_t off_end_offset,
 					      bool is_failure)
 {
 	int debug_id = buffer->debug_id;
-	binder_size_t off_start_offset, buffer_offset, off_end_offset;
+	binder_size_t off_start_offset, buffer_offset;
 
 	binder_debug(BINDER_DEBUG_TRANSACTION,
 		     "%d buffer release %d, size %zd-%zd, failed at %llx\n",
 		     proc->pid, buffer->debug_id,
 		     buffer->data_size, buffer->offsets_size,
-		     (unsigned long long)failed_at);
+		     (unsigned long long)off_end_offset);
 
 	if (buffer->target_node)
 		binder_dec_node(buffer->target_node, 1, 0);
 
 	off_start_offset = ALIGN(buffer->data_size, sizeof(void *));
-	off_end_offset = is_failure ? failed_at :
-				off_start_offset + buffer->offsets_size;
+
 	for (buffer_offset = off_start_offset; buffer_offset < off_end_offset;
 	     buffer_offset += sizeof(binder_size_t)) {
 		struct binder_object_header *hdr;
@@ -1882,7 +1940,7 @@
 		if (!binder_alloc_copy_from_buffer(&proc->alloc, &object_offset,
 						   buffer, buffer_offset,
 						   sizeof(object_offset)))
-			object_size = binder_get_object(proc, buffer,
+			object_size = binder_get_object(proc, NULL, buffer,
 							object_offset, &object);
 		if (object_size == 0) {
 			pr_err("transaction release %d bad object at offset %lld, size %zd\n",
@@ -1956,9 +2014,8 @@
 			binder_size_t fd_buf_size;
 			binder_size_t num_valid;
 
-			if (proc->tsk != current->group_leader) {
+			if (is_failure) {
 				/*
-				 * Nothing to do if running in sender context
 				 * The fd fixups have not been applied so no
 				 * fds need to be closed.
 				 */
@@ -2032,6 +2089,21 @@
 	}
 }
 
+/* Clean up all the objects in the buffer */
+static inline void binder_release_entire_buffer(struct binder_proc *proc,
+						struct binder_thread *thread,
+						struct binder_buffer *buffer,
+						bool is_failure)
+{
+	binder_size_t off_end_offset;
+
+	off_end_offset = ALIGN(buffer->data_size, sizeof(void *));
+	off_end_offset += buffer->offsets_size;
+
+	binder_transaction_buffer_release(proc, thread, buffer,
+					  off_end_offset, is_failure);
+}
+
 static int binder_translate_binder(struct flat_binder_object *fp,
 				   struct binder_transaction *t,
 				   struct binder_thread *thread)
@@ -2056,7 +2128,7 @@
 		ret = -EINVAL;
 		goto done;
 	}
-	if (security_binder_transfer_binder(proc->tsk, target_proc->tsk)) {
+	if (security_binder_transfer_binder(proc->cred, target_proc->cred)) {
 		ret = -EPERM;
 		goto done;
 	}
@@ -2102,7 +2174,7 @@
 				  proc->pid, thread->pid, fp->handle);
 		return -EINVAL;
 	}
-	if (security_binder_transfer_binder(proc->tsk, target_proc->tsk)) {
+	if (security_binder_transfer_binder(proc->cred, target_proc->cred)) {
 		ret = -EPERM;
 		goto done;
 	}
@@ -2190,7 +2262,7 @@
 		ret = -EBADF;
 		goto err_fget;
 	}
-	ret = security_binder_transfer_file(proc->tsk, target_proc->tsk, file);
+	ret = security_binder_transfer_file(proc->cred, target_proc->cred, file);
 	if (ret < 0) {
 		ret = -EPERM;
 		goto err_security;
@@ -2221,16 +2293,266 @@
 	return ret;
 }
 
-static int binder_translate_fd_array(struct binder_fd_array_object *fda,
+/**
+ * struct binder_ptr_fixup - data to be fixed-up in target buffer
+ * @offset	offset in target buffer to fixup
+ * @skip_size	bytes to skip in copy (fixup will be written later)
+ * @fixup_data	data to write at fixup offset
+ * @node	list node
+ *
+ * This is used for the pointer fixup list (pf) which is created and consumed
+ * during binder_transaction() and is only accessed locally. No
+ * locking is necessary.
+ *
+ * The list is ordered by @offset.
+ */
+struct binder_ptr_fixup {
+	binder_size_t offset;
+	size_t skip_size;
+	binder_uintptr_t fixup_data;
+	struct list_head node;
+};
+
+/**
+ * struct binder_sg_copy - scatter-gather data to be copied
+ * @offset		offset in target buffer
+ * @sender_uaddr	user address in source buffer
+ * @length		bytes to copy
+ * @node		list node
+ *
+ * This is used for the sg copy list (sgc) which is created and consumed
+ * during binder_transaction() and is only accessed locally. No
+ * locking is necessary.
+ *
+ * The list is ordered by @offset.
+ */
+struct binder_sg_copy {
+	binder_size_t offset;
+	const void __user *sender_uaddr;
+	size_t length;
+	struct list_head node;
+};
+
+/**
+ * binder_do_deferred_txn_copies() - copy and fixup scatter-gather data
+ * @alloc:	binder_alloc associated with @buffer
+ * @buffer:	binder buffer in target process
+ * @sgc_head:	list_head of scatter-gather copy list
+ * @pf_head:	list_head of pointer fixup list
+ *
+ * Processes all elements of @sgc_head, applying fixups from @pf_head
+ * and copying the scatter-gather data from the source process' user
+ * buffer to the target's buffer. It is expected that the list creation
+ * and processing all occurs during binder_transaction() so these lists
+ * are only accessed in local context.
+ *
+ * Return: 0=success, else -errno
+ */
+static int binder_do_deferred_txn_copies(struct binder_alloc *alloc,
+					 struct binder_buffer *buffer,
+					 struct list_head *sgc_head,
+					 struct list_head *pf_head)
+{
+	int ret = 0;
+	struct binder_sg_copy *sgc, *tmpsgc;
+	struct binder_ptr_fixup *tmppf;
+	struct binder_ptr_fixup *pf =
+		list_first_entry_or_null(pf_head, struct binder_ptr_fixup,
+					 node);
+
+	list_for_each_entry_safe(sgc, tmpsgc, sgc_head, node) {
+		size_t bytes_copied = 0;
+
+		while (bytes_copied < sgc->length) {
+			size_t copy_size;
+			size_t bytes_left = sgc->length - bytes_copied;
+			size_t offset = sgc->offset + bytes_copied;
+
+			/*
+			 * We copy up to the fixup (pointed to by pf)
+			 */
+			copy_size = pf ? min(bytes_left, (size_t)pf->offset - offset)
+				       : bytes_left;
+			if (!ret && copy_size)
+				ret = binder_alloc_copy_user_to_buffer(
+						alloc, buffer,
+						offset,
+						sgc->sender_uaddr + bytes_copied,
+						copy_size);
+			bytes_copied += copy_size;
+			if (copy_size != bytes_left) {
+				BUG_ON(!pf);
+				/* we stopped at a fixup offset */
+				if (pf->skip_size) {
+					/*
+					 * we are just skipping. This is for
+					 * BINDER_TYPE_FDA where the translated
+					 * fds will be fixed up when we get
+					 * to target context.
+					 */
+					bytes_copied += pf->skip_size;
+				} else {
+					/* apply the fixup indicated by pf */
+					if (!ret)
+						ret = binder_alloc_copy_to_buffer(
+							alloc, buffer,
+							pf->offset,
+							&pf->fixup_data,
+							sizeof(pf->fixup_data));
+					bytes_copied += sizeof(pf->fixup_data);
+				}
+				list_del(&pf->node);
+				kfree(pf);
+				pf = list_first_entry_or_null(pf_head,
+						struct binder_ptr_fixup, node);
+			}
+		}
+		list_del(&sgc->node);
+		kfree(sgc);
+	}
+	list_for_each_entry_safe(pf, tmppf, pf_head, node) {
+		BUG_ON(pf->skip_size == 0);
+		list_del(&pf->node);
+		kfree(pf);
+	}
+	BUG_ON(!list_empty(sgc_head));
+
+	return ret > 0 ? -EINVAL : ret;
+}
+
+/**
+ * binder_cleanup_deferred_txn_lists() - free specified lists
+ * @sgc_head:	list_head of scatter-gather copy list
+ * @pf_head:	list_head of pointer fixup list
+ *
+ * Called to clean up @sgc_head and @pf_head if there is an
+ * error.
+ */
+static void binder_cleanup_deferred_txn_lists(struct list_head *sgc_head,
+					      struct list_head *pf_head)
+{
+	struct binder_sg_copy *sgc, *tmpsgc;
+	struct binder_ptr_fixup *pf, *tmppf;
+
+	list_for_each_entry_safe(sgc, tmpsgc, sgc_head, node) {
+		list_del(&sgc->node);
+		kfree(sgc);
+	}
+	list_for_each_entry_safe(pf, tmppf, pf_head, node) {
+		list_del(&pf->node);
+		kfree(pf);
+	}
+}
+
+/**
+ * binder_defer_copy() - queue a scatter-gather buffer for copy
+ * @sgc_head:		list_head of scatter-gather copy list
+ * @offset:		binder buffer offset in target process
+ * @sender_uaddr:	user address in source process
+ * @length:		bytes to copy
+ *
+ * Specify a scatter-gather block to be copied. The actual copy must
+ * be deferred until all the needed fixups are identified and queued.
+ * Then the copy and fixups are done together so un-translated values
+ * from the source are never visible in the target buffer.
+ *
+ * We are guaranteed that repeated calls to this function will have
+ * monotonically increasing @offset values so the list will naturally
+ * be ordered.
+ *
+ * Return: 0=success, else -errno
+ */
+static int binder_defer_copy(struct list_head *sgc_head, binder_size_t offset,
+			     const void __user *sender_uaddr, size_t length)
+{
+	struct binder_sg_copy *bc = kzalloc(sizeof(*bc), GFP_KERNEL);
+
+	if (!bc)
+		return -ENOMEM;
+
+	bc->offset = offset;
+	bc->sender_uaddr = sender_uaddr;
+	bc->length = length;
+	INIT_LIST_HEAD(&bc->node);
+
+	/*
+	 * We are guaranteed that the deferred copies are in-order
+	 * so just add to the tail.
+	 */
+	list_add_tail(&bc->node, sgc_head);
+
+	return 0;
+}
+
+/**
+ * binder_add_fixup() - queue a fixup to be applied to sg copy
+ * @pf_head:	list_head of binder ptr fixup list
+ * @offset:	binder buffer offset in target process
+ * @fixup:	bytes to be copied for fixup
+ * @skip_size:	bytes to skip when copying (fixup will be applied later)
+ *
+ * Add the specified fixup to a list ordered by @offset. When copying
+ * the scatter-gather buffers, the fixup will be copied instead of
+ * data from the source buffer. For BINDER_TYPE_FDA fixups, the fixup
+ * will be applied later (in target process context), so we just skip
+ * the bytes specified by @skip_size. If @skip_size is 0, we copy the
+ * value in @fixup.
+ *
+ * This function is called *mostly* in @offset order, but there are
+ * exceptions. Since out-of-order inserts are relatively uncommon,
+ * we insert the new element by searching backward from the tail of
+ * the list.
+ *
+ * Return: 0=success, else -errno
+ */
+static int binder_add_fixup(struct list_head *pf_head, binder_size_t offset,
+			    binder_uintptr_t fixup, size_t skip_size)
+{
+	struct binder_ptr_fixup *pf = kzalloc(sizeof(*pf), GFP_KERNEL);
+	struct binder_ptr_fixup *tmppf;
+
+	if (!pf)
+		return -ENOMEM;
+
+	pf->offset = offset;
+	pf->fixup_data = fixup;
+	pf->skip_size = skip_size;
+	INIT_LIST_HEAD(&pf->node);
+
+	/* Fixups are *mostly* added in-order, but there are some
+	 * exceptions. Look backwards through list for insertion point.
+	 */
+	list_for_each_entry_reverse(tmppf, pf_head, node) {
+		if (tmppf->offset < pf->offset) {
+			list_add(&pf->node, &tmppf->node);
+			return 0;
+		}
+	}
+	/*
+	 * if we get here, then the new offset is the lowest so
+	 * insert at the head
+	 */
+	list_add(&pf->node, pf_head);
+	return 0;
+}
+
+static int binder_translate_fd_array(struct list_head *pf_head,
+				     struct binder_fd_array_object *fda,
+				     const void __user *sender_ubuffer,
 				     struct binder_buffer_object *parent,
+				     struct binder_buffer_object *sender_uparent,
 				     struct binder_transaction *t,
 				     struct binder_thread *thread,
 				     struct binder_transaction *in_reply_to)
 {
 	binder_size_t fdi, fd_buf_size;
 	binder_size_t fda_offset;
+	const void __user *sender_ufda_base;
 	struct binder_proc *proc = thread->proc;
-	struct binder_proc *target_proc = t->to_proc;
+	int ret;
+
+	if (fda->num_fds == 0)
+		return 0;
 
 	fd_buf_size = sizeof(u32) * fda->num_fds;
 	if (fda->num_fds >= SIZE_MAX / sizeof(u32)) {
@@ -2254,29 +2576,36 @@
 	 */
 	fda_offset = (parent->buffer - (uintptr_t)t->buffer->user_data) +
 		fda->parent_offset;
-	if (!IS_ALIGNED((unsigned long)fda_offset, sizeof(u32))) {
+	sender_ufda_base = (void __user *)(uintptr_t)sender_uparent->buffer +
+				fda->parent_offset;
+
+	if (!IS_ALIGNED((unsigned long)fda_offset, sizeof(u32)) ||
+	    !IS_ALIGNED((unsigned long)sender_ufda_base, sizeof(u32))) {
 		binder_user_error("%d:%d parent offset not aligned correctly.\n",
 				  proc->pid, thread->pid);
 		return -EINVAL;
 	}
+	ret = binder_add_fixup(pf_head, fda_offset, 0, fda->num_fds * sizeof(u32));
+	if (ret)
+		return ret;
+
 	for (fdi = 0; fdi < fda->num_fds; fdi++) {
 		u32 fd;
-		int ret;
 		binder_size_t offset = fda_offset + fdi * sizeof(fd);
+		binder_size_t sender_uoffset = fdi * sizeof(fd);
 
-		ret = binder_alloc_copy_from_buffer(&target_proc->alloc,
-						    &fd, t->buffer,
-						    offset, sizeof(fd));
+		ret = copy_from_user(&fd, sender_ufda_base + sender_uoffset, sizeof(fd));
 		if (!ret)
 			ret = binder_translate_fd(fd, offset, t, thread,
 						  in_reply_to);
-		if (ret < 0)
-			return ret;
+		if (ret)
+			return ret > 0 ? -EINVAL : ret;
 	}
 	return 0;
 }
 
-static int binder_fixup_parent(struct binder_transaction *t,
+static int binder_fixup_parent(struct list_head *pf_head,
+			       struct binder_transaction *t,
 			       struct binder_thread *thread,
 			       struct binder_buffer_object *bp,
 			       binder_size_t off_start_offset,
@@ -2322,14 +2651,7 @@
 	}
 	buffer_offset = bp->parent_offset +
 			(uintptr_t)parent->buffer - (uintptr_t)b->user_data;
-	if (binder_alloc_copy_to_buffer(&target_proc->alloc, b, buffer_offset,
-					&bp->buffer, sizeof(bp->buffer))) {
-		binder_user_error("%d:%d got transaction with invalid parent offset\n",
-				  proc->pid, thread->pid);
-		return -EINVAL;
-	}
-
-	return 0;
+	return binder_add_fixup(pf_head, buffer_offset, bp->buffer, 0);
 }
 
 /**
@@ -2456,6 +2778,7 @@
 	binder_size_t off_start_offset, off_end_offset;
 	binder_size_t off_min;
 	binder_size_t sg_buf_offset, sg_buf_end_offset;
+	binder_size_t user_offset = 0;
 	struct binder_proc *target_proc = NULL;
 	struct binder_thread *target_thread = NULL;
 	struct binder_node *target_node = NULL;
@@ -2468,8 +2791,13 @@
 	binder_size_t last_fixup_min_off = 0;
 	struct binder_context *context = proc->context;
 	int t_debug_id = atomic_inc_return(&binder_last_id);
-	char *secctx = NULL;
-	u32 secctx_sz = 0;
+	struct lsmcontext lsmctx = { };
+	struct list_head sgc_head;
+	struct list_head pf_head;
+	const void __user *user_buffer = (const void __user *)
+				(uintptr_t)tr->data.ptr.buffer;
+	INIT_LIST_HEAD(&sgc_head);
+	INIT_LIST_HEAD(&pf_head);
 
 	e = binder_transaction_log_add(&binder_transaction_log);
 	e->debug_id = t_debug_id;
@@ -2595,8 +2923,8 @@
 			return_error_line = __LINE__;
 			goto err_invalid_target_handle;
 		}
-		if (security_binder_transaction(proc->tsk,
-						target_proc->tsk) < 0) {
+		if (security_binder_transaction(proc->cred,
+						target_proc->cred) < 0) {
 			return_error = BR_FAILED_REPLY;
 			return_error_param = -EPERM;
 			return_error_line = __LINE__;
@@ -2719,7 +3047,7 @@
 	t->priority = task_nice(current);
 
 	if (target_node && target_node->txn_security_ctx) {
-		u32 secid;
+		struct lsmblob blob;
 		size_t added_size;
 
 		/*
@@ -2731,15 +3059,15 @@
 		 * here; however, it isn't clear that binder would handle that
 		 * case well anyway.
 		 */
-		security_task_getsecid_obj(proc->tsk, &secid);
-		ret = security_secid_to_secctx(secid, &secctx, &secctx_sz);
+		security_cred_getsecid(proc->cred, &blob);
+		ret = security_secid_to_secctx(&blob, &lsmctx, LSMBLOB_DISPLAY);
 		if (ret) {
 			return_error = BR_FAILED_REPLY;
 			return_error_param = ret;
 			return_error_line = __LINE__;
 			goto err_get_secctx_failed;
 		}
-		added_size = ALIGN(secctx_sz, sizeof(u64));
+		added_size = ALIGN(lsmctx.len, sizeof(u64));
 		extra_buffers_size += added_size;
 		if (extra_buffers_size < added_size) {
 			/* integer overflow of extra_buffers_size */
@@ -2766,23 +3094,22 @@
 		t->buffer = NULL;
 		goto err_binder_alloc_buf_failed;
 	}
-	if (secctx) {
+	if (lsmctx.context) {
 		int err;
 		size_t buf_offset = ALIGN(tr->data_size, sizeof(void *)) +
 				    ALIGN(tr->offsets_size, sizeof(void *)) +
 				    ALIGN(extra_buffers_size, sizeof(void *)) -
-				    ALIGN(secctx_sz, sizeof(u64));
+				    ALIGN(lsmctx.len, sizeof(u64));
 
 		t->security_ctx = (uintptr_t)t->buffer->user_data + buf_offset;
 		err = binder_alloc_copy_to_buffer(&target_proc->alloc,
 						  t->buffer, buf_offset,
-						  secctx, secctx_sz);
+						  lsmctx.context, lsmctx.len);
 		if (err) {
 			t->security_ctx = 0;
 			WARN_ON(1);
 		}
-		security_release_secctx(secctx, secctx_sz);
-		secctx = NULL;
+		security_release_secctx(&lsmctx);
 	}
 	t->buffer->debug_id = t->debug_id;
 	t->buffer->transaction = t;
@@ -2792,19 +3119,6 @@
 
 	if (binder_alloc_copy_user_to_buffer(
 				&target_proc->alloc,
-				t->buffer, 0,
-				(const void __user *)
-					(uintptr_t)tr->data.ptr.buffer,
-				tr->data_size)) {
-		binder_user_error("%d:%d got transaction with invalid data ptr\n",
-				proc->pid, thread->pid);
-		return_error = BR_FAILED_REPLY;
-		return_error_param = -EFAULT;
-		return_error_line = __LINE__;
-		goto err_copy_data_failed;
-	}
-	if (binder_alloc_copy_user_to_buffer(
-				&target_proc->alloc,
 				t->buffer,
 				ALIGN(tr->data_size, sizeof(void *)),
 				(const void __user *)
@@ -2839,7 +3153,7 @@
 	off_end_offset = off_start_offset + tr->offsets_size;
 	sg_buf_offset = ALIGN(off_end_offset, sizeof(void *));
 	sg_buf_end_offset = sg_buf_offset + extra_buffers_size -
-		ALIGN(secctx_sz, sizeof(u64));
+		ALIGN(lsmctx.len, sizeof(u64));
 	off_min = 0;
 	for (buffer_offset = off_start_offset; buffer_offset < off_end_offset;
 	     buffer_offset += sizeof(binder_size_t)) {
@@ -2847,6 +3161,7 @@
 		size_t object_size;
 		struct binder_object object;
 		binder_size_t object_offset;
+		binder_size_t copy_size;
 
 		if (binder_alloc_copy_from_buffer(&target_proc->alloc,
 						  &object_offset,
@@ -2858,8 +3173,28 @@
 			return_error_line = __LINE__;
 			goto err_bad_offset;
 		}
-		object_size = binder_get_object(target_proc, t->buffer,
-						object_offset, &object);
+
+		/*
+		 * Copy the source user buffer up to the next object
+		 * that will be processed.
+		 */
+		copy_size = object_offset - user_offset;
+		if (copy_size && (user_offset > object_offset ||
+				object_offset > tr->data_size ||
+				binder_alloc_copy_user_to_buffer(
+					&target_proc->alloc,
+					t->buffer, user_offset,
+					user_buffer + user_offset,
+					copy_size))) {
+			binder_user_error("%d:%d got transaction with invalid data ptr\n",
+					proc->pid, thread->pid);
+			return_error = BR_FAILED_REPLY;
+			return_error_param = -EFAULT;
+			return_error_line = __LINE__;
+			goto err_copy_data_failed;
+		}
+		object_size = binder_get_object(target_proc, user_buffer,
+				t->buffer, object_offset, &object);
 		if (object_size == 0 || object_offset < off_min) {
 			binder_user_error("%d:%d got transaction with invalid offset (%lld, min %lld max %lld) or object.\n",
 					  proc->pid, thread->pid,
@@ -2871,6 +3206,11 @@
 			return_error_line = __LINE__;
 			goto err_bad_offset;
 		}
+		/*
+		 * Set offset to the next buffer fragment to be
+		 * copied
+		 */
+		user_offset = object_offset + object_size;
 
 		hdr = &object.hdr;
 		off_min = object_offset + object_size;
@@ -2933,6 +3273,8 @@
 		case BINDER_TYPE_FDA: {
 			struct binder_object ptr_object;
 			binder_size_t parent_offset;
+			struct binder_object user_object;
+			size_t user_parent_size;
 			struct binder_fd_array_object *fda =
 				to_binder_fd_array_object(hdr);
 			size_t num_valid = (buffer_offset - off_start_offset) /
@@ -2964,11 +3306,35 @@
 				return_error_line = __LINE__;
 				goto err_bad_parent;
 			}
-			ret = binder_translate_fd_array(fda, parent, t, thread,
-							in_reply_to);
-			if (ret < 0) {
+			/*
+			 * We need to read the user version of the parent
+			 * object to get the original user offset
+			 */
+			user_parent_size =
+				binder_get_object(proc, user_buffer, t->buffer,
+						  parent_offset, &user_object);
+			if (user_parent_size != sizeof(user_object.bbo)) {
+				binder_user_error("%d:%d invalid ptr object size: %zd vs %zd\n",
+						  proc->pid, thread->pid,
+						  user_parent_size,
+						  sizeof(user_object.bbo));
 				return_error = BR_FAILED_REPLY;
-				return_error_param = ret;
+				return_error_param = -EINVAL;
+				return_error_line = __LINE__;
+				goto err_bad_parent;
+			}
+			ret = binder_translate_fd_array(&pf_head, fda,
+							user_buffer, parent,
+							&user_object.bbo, t,
+							thread, in_reply_to);
+			if (!ret)
+				ret = binder_alloc_copy_to_buffer(&target_proc->alloc,
+								  t->buffer,
+								  object_offset,
+								  fda, sizeof(*fda));
+			if (ret) {
+				return_error = BR_FAILED_REPLY;
+				return_error_param = ret > 0 ? -EINVAL : ret;
 				return_error_line = __LINE__;
 				goto err_translate_failed;
 			}
@@ -2990,19 +3356,14 @@
 				return_error_line = __LINE__;
 				goto err_bad_offset;
 			}
-			if (binder_alloc_copy_user_to_buffer(
-						&target_proc->alloc,
-						t->buffer,
-						sg_buf_offset,
-						(const void __user *)
-							(uintptr_t)bp->buffer,
-						bp->length)) {
-				binder_user_error("%d:%d got transaction with invalid offsets ptr\n",
-						  proc->pid, thread->pid);
-				return_error_param = -EFAULT;
+			ret = binder_defer_copy(&sgc_head, sg_buf_offset,
+				(const void __user *)(uintptr_t)bp->buffer,
+				bp->length);
+			if (ret) {
 				return_error = BR_FAILED_REPLY;
+				return_error_param = ret;
 				return_error_line = __LINE__;
-				goto err_copy_data_failed;
+				goto err_translate_failed;
 			}
 			/* Fixup buffer pointer to target proc address space */
 			bp->buffer = (uintptr_t)
@@ -3011,7 +3372,8 @@
 
 			num_valid = (buffer_offset - off_start_offset) /
 					sizeof(binder_size_t);
-			ret = binder_fixup_parent(t, thread, bp,
+			ret = binder_fixup_parent(&pf_head, t,
+						  thread, bp,
 						  off_start_offset,
 						  num_valid,
 						  last_fixup_obj_off,
@@ -3038,6 +3400,30 @@
 			goto err_bad_object_type;
 		}
 	}
+	/* Done processing objects, copy the rest of the buffer */
+	if (binder_alloc_copy_user_to_buffer(
+				&target_proc->alloc,
+				t->buffer, user_offset,
+				user_buffer + user_offset,
+				tr->data_size - user_offset)) {
+		binder_user_error("%d:%d got transaction with invalid data ptr\n",
+				proc->pid, thread->pid);
+		return_error = BR_FAILED_REPLY;
+		return_error_param = -EFAULT;
+		return_error_line = __LINE__;
+		goto err_copy_data_failed;
+	}
+
+	ret = binder_do_deferred_txn_copies(&target_proc->alloc, t->buffer,
+					    &sgc_head, &pf_head);
+	if (ret) {
+		binder_user_error("%d:%d got transaction with invalid offsets ptr\n",
+				  proc->pid, thread->pid);
+		return_error = BR_FAILED_REPLY;
+		return_error_param = ret;
+		return_error_line = __LINE__;
+		goto err_copy_data_failed;
+	}
 	if (t->buffer->oneway_spam_suspect)
 		tcomplete->type = BINDER_WORK_TRANSACTION_ONEWAY_SPAM_SUSPECT;
 	else
@@ -3111,6 +3497,7 @@
 err_bad_offset:
 err_bad_parent:
 err_copy_data_failed:
+	binder_cleanup_deferred_txn_lists(&sgc_head, &pf_head);
 	binder_free_txn_fixups(t);
 	trace_binder_transaction_failed_buffer_release(t->buffer);
 	binder_transaction_buffer_release(target_proc, NULL, t->buffer,
@@ -3122,8 +3509,8 @@
 	binder_alloc_free_buf(&target_proc->alloc, t->buffer);
 err_binder_alloc_buf_failed:
 err_bad_extra_size:
-	if (secctx)
-		security_release_secctx(secctx, secctx_sz);
+	if (lsmctx.context)
+		security_release_secctx(&lsmctx);
 err_get_secctx_failed:
 	kfree(tcomplete);
 	binder_stats_deleted(BINDER_STAT_TRANSACTION_COMPLETE);
@@ -3185,6 +3572,7 @@
  * binder_free_buf() - free the specified buffer
  * @proc:	binder proc that owns buffer
  * @buffer:	buffer to be freed
+ * @is_failure:	failed to send transaction
  *
  * If buffer for an async transaction, enqueue the next async
  * transaction from the node.
@@ -3194,7 +3582,7 @@
 static void
 binder_free_buf(struct binder_proc *proc,
 		struct binder_thread *thread,
-		struct binder_buffer *buffer)
+		struct binder_buffer *buffer, bool is_failure)
 {
 	binder_inner_proc_lock(proc);
 	if (buffer->transaction) {
@@ -3222,7 +3610,7 @@
 		binder_node_inner_unlock(buf_node);
 	}
 	trace_binder_transaction_buffer_release(buffer);
-	binder_transaction_buffer_release(proc, thread, buffer, 0, false);
+	binder_release_entire_buffer(proc, thread, buffer, is_failure);
 	binder_alloc_free_buf(&proc->alloc, buffer);
 }
 
@@ -3424,7 +3812,7 @@
 				     proc->pid, thread->pid, (u64)data_ptr,
 				     buffer->debug_id,
 				     buffer->transaction ? "active" : "finished");
-			binder_free_buf(proc, thread, buffer);
+			binder_free_buf(proc, thread, buffer, false);
 			break;
 		}
 
@@ -4117,7 +4505,7 @@
 			buffer->transaction = NULL;
 			binder_cleanup_transaction(t, "fd fixups failed",
 						   BR_FAILED_REPLY);
-			binder_free_buf(proc, thread, buffer);
+			binder_free_buf(proc, thread, buffer, true);
 			binder_debug(BINDER_DEBUG_FAILED_TRANSACTION,
 				     "%d:%d %stransaction %d fd fixups failed %d/%d, line %d\n",
 				     proc->pid, thread->pid,
@@ -4250,6 +4638,7 @@
 				"undelivered TRANSACTION_ERROR: %u\n",
 				e->cmd);
 		} break;
+		case BINDER_WORK_TRANSACTION_ONEWAY_SPAM_SUSPECT:
 		case BINDER_WORK_TRANSACTION_COMPLETE: {
 			binder_debug(BINDER_DEBUG_DEAD_TRANSACTION,
 				"undelivered TRANSACTION_COMPLETE\n");
@@ -4353,6 +4742,7 @@
 	}
 	binder_alloc_deferred_release(&proc->alloc);
 	put_task_struct(proc->tsk);
+	put_cred(proc->cred);
 	binder_stats_deleted(BINDER_STAT_PROC);
 	kfree(proc);
 }
@@ -4430,23 +4820,20 @@
 	__release(&t->lock);
 
 	/*
-	 * If this thread used poll, make sure we remove the waitqueue
-	 * from any epoll data structures holding it with POLLFREE.
-	 * waitqueue_active() is safe to use here because we're holding
-	 * the inner lock.
+	 * If this thread used poll, make sure we remove the waitqueue from any
+	 * poll data structures holding it.
 	 */
-	if ((thread->looper & BINDER_LOOPER_STATE_POLL) &&
-	    waitqueue_active(&thread->wait)) {
-		wake_up_poll(&thread->wait, EPOLLHUP | POLLFREE);
-	}
+	if (thread->looper & BINDER_LOOPER_STATE_POLL)
+		wake_up_pollfree(&thread->wait);
 
 	binder_inner_proc_unlock(thread->proc);
 
 	/*
-	 * This is needed to avoid races between wake_up_poll() above and
-	 * and ep_remove_waitqueue() called for other reasons (eg the epoll file
-	 * descriptor being closed); ep_remove_waitqueue() holds an RCU read
-	 * lock, so we can be sure it's done after calling synchronize_rcu().
+	 * This is needed to avoid races between wake_up_pollfree() above and
+	 * someone else removing the last entry from the queue for other reasons
+	 * (e.g. ep_remove_wait_queue() being called due to an epoll file
+	 * descriptor being closed).  Such other users hold an RCU read lock, so
+	 * we can be sure they're done after we call synchronize_rcu().
 	 */
 	if (thread->looper & BINDER_LOOPER_STATE_POLL)
 		synchronize_rcu();
@@ -4467,7 +4854,7 @@
 
 	thread = binder_get_thread(proc);
 	if (!thread)
-		return POLLERR;
+		return EPOLLERR;
 
 	binder_inner_proc_lock(thread->proc);
 	thread->looper |= BINDER_LOOPER_STATE_POLL;
@@ -4564,7 +4951,7 @@
 		ret = -EBUSY;
 		goto out;
 	}
-	ret = security_binder_set_context_mgr(proc->tsk);
+	ret = security_binder_set_context_mgr(proc->cred);
 	if (ret < 0)
 		goto out;
 	if (uid_valid(context->binder_context_mgr_uid)) {
@@ -4784,7 +5171,7 @@
 			goto err;
 		break;
 	case BINDER_SET_MAX_THREADS: {
-		int max_threads;
+		u32 max_threads;
 
 		if (copy_from_user(&max_threads, ubuf,
 				   sizeof(max_threads))) {
@@ -5055,6 +5442,7 @@
 	spin_lock_init(&proc->outer_lock);
 	get_task_struct(current->group_leader);
 	proc->tsk = current->group_leader;
+	proc->cred = get_cred(filp->f_cred);
 	INIT_LIST_HEAD(&proc->todo);
 	init_waitqueue_head(&proc->freeze_wait);
 	proc->default_priority = task_nice(current);
@@ -5765,8 +6153,7 @@
 	print_binder_stats(m, "  ", &proc->stats);
 }
 
-
-int binder_state_show(struct seq_file *m, void *unused)
+static int state_show(struct seq_file *m, void *unused)
 {
 	struct binder_proc *proc;
 	struct binder_node *node;
@@ -5805,7 +6192,7 @@
 	return 0;
 }
 
-int binder_stats_show(struct seq_file *m, void *unused)
+static int stats_show(struct seq_file *m, void *unused)
 {
 	struct binder_proc *proc;
 
@@ -5821,7 +6208,7 @@
 	return 0;
 }
 
-int binder_transactions_show(struct seq_file *m, void *unused)
+static int transactions_show(struct seq_file *m, void *unused)
 {
 	struct binder_proc *proc;
 
@@ -5877,7 +6264,7 @@
 			"\n" : " (incomplete)\n");
 }
 
-int binder_transaction_log_show(struct seq_file *m, void *unused)
+static int transaction_log_show(struct seq_file *m, void *unused)
 {
 	struct binder_transaction_log *log = m->private;
 	unsigned int log_cur = atomic_read(&log->cur);
@@ -5909,6 +6296,45 @@
 	.release = binder_release,
 };
 
+DEFINE_SHOW_ATTRIBUTE(state);
+DEFINE_SHOW_ATTRIBUTE(stats);
+DEFINE_SHOW_ATTRIBUTE(transactions);
+DEFINE_SHOW_ATTRIBUTE(transaction_log);
+
+const struct binder_debugfs_entry binder_debugfs_entries[] = {
+	{
+		.name = "state",
+		.mode = 0444,
+		.fops = &state_fops,
+		.data = NULL,
+	},
+	{
+		.name = "stats",
+		.mode = 0444,
+		.fops = &stats_fops,
+		.data = NULL,
+	},
+	{
+		.name = "transactions",
+		.mode = 0444,
+		.fops = &transactions_fops,
+		.data = NULL,
+	},
+	{
+		.name = "transaction_log",
+		.mode = 0444,
+		.fops = &transaction_log_fops,
+		.data = &binder_transaction_log,
+	},
+	{
+		.name = "failed_transaction_log",
+		.mode = 0444,
+		.fops = &transaction_log_fops,
+		.data = &binder_transaction_log_failed,
+	},
+	{} /* terminator */
+};
+
 static int __init init_binder_device(const char *name)
 {
 	int ret;
@@ -5954,36 +6380,18 @@
 	atomic_set(&binder_transaction_log_failed.cur, ~0U);
 
 	binder_debugfs_dir_entry_root = debugfs_create_dir("binder", NULL);
-	if (binder_debugfs_dir_entry_root)
+	if (binder_debugfs_dir_entry_root) {
+		const struct binder_debugfs_entry *db_entry;
+
+		binder_for_each_debugfs_entry(db_entry)
+			debugfs_create_file(db_entry->name,
+					    db_entry->mode,
+					    binder_debugfs_dir_entry_root,
+					    db_entry->data,
+					    db_entry->fops);
+
 		binder_debugfs_dir_entry_proc = debugfs_create_dir("proc",
 						 binder_debugfs_dir_entry_root);
-
-	if (binder_debugfs_dir_entry_root) {
-		debugfs_create_file("state",
-				    0444,
-				    binder_debugfs_dir_entry_root,
-				    NULL,
-				    &binder_state_fops);
-		debugfs_create_file("stats",
-				    0444,
-				    binder_debugfs_dir_entry_root,
-				    NULL,
-				    &binder_stats_fops);
-		debugfs_create_file("transactions",
-				    0444,
-				    binder_debugfs_dir_entry_root,
-				    NULL,
-				    &binder_transactions_fops);
-		debugfs_create_file("transaction_log",
-				    0444,
-				    binder_debugfs_dir_entry_root,
-				    &binder_transaction_log,
-				    &binder_transaction_log_fops);
-		debugfs_create_file("failed_transaction_log",
-				    0444,
-				    binder_debugfs_dir_entry_root,
-				    &binder_transaction_log_failed,
-				    &binder_transaction_log_fops);
 	}
 
 	if (!IS_ENABLED(CONFIG_ANDROID_BINDERFS) &&
@@ -6023,13 +6431,25 @@
 
 err_alloc_device_names_failed:
 	debugfs_remove_recursive(binder_debugfs_dir_entry_root);
+	binder_alloc_shrinker_exit();
 
 	return ret;
 }
 
-device_initcall(binder_init);
+module_init(binder_init);
+/*
+ * binder will have no exit function since binderfs instances can be mounted
+ * multiple times and also in user namespaces finding and destroying them all
+ * is not feasible without introducing insane locking. Just ignoring existing
+ * instances on module unload also wouldn't work since we would loose track of
+ * what major numer was dynamically allocated and also what minor numbers are
+ * already given out. So this would get us into all kinds of issues with device
+ * number reuse. So simply don't allow unloading unless we are forced to do so.
+ */
+
+MODULE_AUTHOR("Google, Inc.");
+MODULE_DESCRIPTION("Driver for Android binder device");
+MODULE_LICENSE("GPL v2");
 
 #define CREATE_TRACE_POINTS
 #include "binder_trace.h"
-
-MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/binder_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/binder_alloc.c
@@ -38,8 +38,7 @@
 };
 static uint32_t binder_alloc_debug_mask = BINDER_DEBUG_USER_ERROR;
 
-module_param_named(debug_mask, binder_alloc_debug_mask,
-		   uint, 0644);
+module_param_named(alloc_debug_mask, binder_alloc_debug_mask, uint, 0644);
 
 #define binder_alloc_debug(mask, x...) \
 	do { \
@@ -212,7 +211,7 @@
 		mm = alloc->vma_vm_mm;
 
 	if (mm) {
-		mmap_read_lock(mm);
+		mmap_write_lock(mm);
 		vma = alloc->vma;
 	}
 
@@ -270,8 +269,8 @@
 		trace_binder_alloc_page_end(alloc, index);
 	}
 	if (mm) {
-		mmap_read_unlock(mm);
-		mmput(mm);
+		mmap_write_unlock(mm);
+		mmput_async(mm);
 	}
 	return 0;
 
@@ -303,39 +302,24 @@
 	}
 err_no_vma:
 	if (mm) {
-		mmap_read_unlock(mm);
-		mmput(mm);
+		mmap_write_unlock(mm);
+		mmput_async(mm);
 	}
 	return vma ? -ENOMEM : -ESRCH;
 }
 
-
 static inline void binder_alloc_set_vma(struct binder_alloc *alloc,
 		struct vm_area_struct *vma)
 {
-	if (vma)
-		alloc->vma_vm_mm = vma->vm_mm;
-	/*
-	 * If we see alloc->vma is not NULL, buffer data structures set up
-	 * completely. Look at smp_rmb side binder_alloc_get_vma.
-	 * We also want to guarantee new alloc->vma_vm_mm is always visible
-	 * if alloc->vma is set.
-	 */
-	smp_wmb();
-	alloc->vma = vma;
+	/* pairs with smp_load_acquire in binder_alloc_get_vma() */
+	smp_store_release(&alloc->vma, vma);
 }
 
 static inline struct vm_area_struct *binder_alloc_get_vma(
 		struct binder_alloc *alloc)
 {
-	struct vm_area_struct *vma = NULL;
-
-	if (alloc->vma) {
-		/* Look at description in binder_alloc_set_vma */
-		smp_rmb();
-		vma = alloc->vma;
-	}
-	return vma;
+	/* pairs with smp_store_release in binder_alloc_set_vma() */
+	return smp_load_acquire(&alloc->vma);
 }
 
 static bool debug_low_async_space_locked(struct binder_alloc *alloc, int pid)
@@ -359,8 +343,7 @@
 			continue;
 		if (!buffer->async_transaction)
 			continue;
-		total_alloc_size += binder_alloc_buffer_size(alloc, buffer)
-			+ sizeof(struct binder_buffer);
+		total_alloc_size += binder_alloc_buffer_size(alloc, buffer);
 		num_buffers++;
 	}
 
@@ -398,6 +381,7 @@
 	size_t size, data_offsets_size;
 	int ret;
 
+	/* Check binder_alloc is fully initialized */
 	if (!binder_alloc_get_vma(alloc)) {
 		binder_alloc_debug(BINDER_DEBUG_USER_ERROR,
 				   "%d: binder_alloc_buf, no vma\n",
@@ -421,17 +405,17 @@
 				alloc->pid, extra_buffers_size);
 		return ERR_PTR(-EINVAL);
 	}
-	if (is_async &&
-	    alloc->free_async_space < size + sizeof(struct binder_buffer)) {
+
+	/* Pad 0-size buffers so they get assigned unique addresses */
+	size = max(size, sizeof(void *));
+
+	if (is_async && alloc->free_async_space < size) {
 		binder_alloc_debug(BINDER_DEBUG_BUFFER_ALLOC,
 			     "%d: binder_alloc_buf size %zd failed, no async space left\n",
 			      alloc->pid, size);
 		return ERR_PTR(-ENOSPC);
 	}
 
-	/* Pad 0-size buffers so they get assigned unique addresses */
-	size = max(size, sizeof(void *));
-
 	while (n) {
 		buffer = rb_entry(n, struct binder_buffer, rb_node);
 		BUG_ON(!buffer->free);
@@ -533,7 +517,7 @@
 	buffer->pid = pid;
 	buffer->oneway_spam_suspect = false;
 	if (is_async) {
-		alloc->free_async_space -= size + sizeof(struct binder_buffer);
+		alloc->free_async_space -= size;
 		binder_alloc_debug(BINDER_DEBUG_BUFFER_ALLOC_ASYNC,
 			     "%d: binder_alloc_buf size %zd async free %zd\n",
 			      alloc->pid, size, alloc->free_async_space);
@@ -571,7 +555,7 @@
  * is the sum of the three given sizes (each rounded up to
  * pointer-sized boundary)
  *
- * Return:	The allocated buffer or %NULL if error
+ * Return:	The allocated buffer or %ERR_PTR(-errno) if error
  */
 struct binder_buffer *binder_alloc_new_buf(struct binder_alloc *alloc,
 					   size_t data_size,
@@ -671,8 +655,7 @@
 	BUG_ON(buffer->user_data > alloc->buffer + alloc->buffer_size);
 
 	if (buffer->async_transaction) {
-		alloc->free_async_space += size + sizeof(struct binder_buffer);
-
+		alloc->free_async_space += buffer_size;
 		binder_alloc_debug(BINDER_DEBUG_BUFFER_ALLOC_ASYNC,
 			     "%d: binder_free_buf size %zd async free %zd\n",
 			      alloc->pid, size, alloc->free_async_space);
@@ -720,7 +703,7 @@
 	/*
 	 * We could eliminate the call to binder_alloc_clear_buf()
 	 * from binder_alloc_deferred_release() by moving this to
-	 * binder_alloc_free_buf_locked(). However, that could
+	 * binder_free_buf_locked(). However, that could
 	 * increase contention for the alloc mutex if clear_on_free
 	 * is used frequently for large buffers. The mutex is not
 	 * needed for correctness here.
@@ -754,6 +737,12 @@
 	const char *failure_string;
 	struct binder_buffer *buffer;
 
+	if (unlikely(vma->vm_mm != alloc->vma_vm_mm)) {
+		ret = -EINVAL;
+		failure_string = "invalid vma->vm_mm";
+		goto err_invalid_mm;
+	}
+
 	mutex_lock(&binder_alloc_mmap_lock);
 	if (alloc->buffer_size) {
 		ret = -EBUSY;
@@ -787,8 +776,9 @@
 	buffer->free = 1;
 	binder_insert_free_buffer(alloc, buffer);
 	alloc->free_async_space = alloc->buffer_size / 2;
+
+	/* Signal binder_alloc is fully initialized */
 	binder_alloc_set_vma(alloc, vma);
-	mmgrab(alloc->vma_vm_mm);
 
 	return 0;
 
@@ -801,6 +791,7 @@
 	alloc->buffer_size = 0;
 err_already_mapped:
 	mutex_unlock(&binder_alloc_mmap_lock);
+err_invalid_mm:
 	binder_alloc_debug(BINDER_DEBUG_USER_ERROR,
 			   "%s: %d %lx-%lx %s failed %d\n", __func__,
 			   alloc->pid, vma->vm_start, vma->vm_end,
@@ -1011,7 +1002,9 @@
 		goto err_mmget;
 	if (!mmap_read_trylock(mm))
 		goto err_mmap_read_lock_failed;
-	vma = binder_alloc_get_vma(alloc);
+	vma = vma_lookup(mm, page_addr);
+	if (vma && vma != binder_alloc_get_vma(alloc))
+		goto err_invalid_vma;
 
 	list_lru_isolate(lru, item);
 	spin_unlock(lock);
@@ -1037,6 +1030,8 @@
 	mutex_unlock(&alloc->mutex);
 	return LRU_REMOVED_RETRY;
 
+err_invalid_vma:
+	mmap_read_unlock(mm);
 err_mmap_read_lock_failed:
 	mmput_async(mm);
 err_mmget:
@@ -1079,6 +1074,8 @@
 void binder_alloc_init(struct binder_alloc *alloc)
 {
 	alloc->pid = current->group_leader->pid;
+	alloc->vma_vm_mm = current->mm;
+	mmgrab(alloc->vma_vm_mm);
 	mutex_init(&alloc->mutex);
 	INIT_LIST_HEAD(&alloc->buffers);
 }
@@ -1095,6 +1092,12 @@
 	return ret;
 }
 
+void binder_alloc_shrinker_exit(void)
+{
+	unregister_shrinker(&binder_shrinker);
+	list_lru_destroy(&binder_alloc_lru);
+}
+
 /**
  * check_buffer() - verify that buffer/offset is safe to access
  * @alloc: binder_alloc for this proc
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/binder_alloc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/binder_alloc.h
@@ -6,6 +6,7 @@
 #ifndef _LINUX_BINDER_ALLOC_H
 #define _LINUX_BINDER_ALLOC_H
 
+#include <linux/kconfig.h>
 #include <linux/rbtree.h>
 #include <linux/list.h>
 #include <linux/mm.h>
@@ -115,7 +116,7 @@
 	bool oneway_spam_detected;
 };
 
-#ifdef CONFIG_ANDROID_BINDER_IPC_SELFTEST
+#if IS_ENABLED(CONFIG_ANDROID_BINDER_IPC_SELFTEST)
 void binder_selftest_alloc(struct binder_alloc *alloc);
 #else
 static inline void binder_selftest_alloc(struct binder_alloc *alloc) {}
@@ -131,6 +132,7 @@
 						  int pid);
 extern void binder_alloc_init(struct binder_alloc *alloc);
 extern int binder_alloc_shrinker_init(void);
+extern void binder_alloc_shrinker_exit(void);
 extern void binder_alloc_vma_close(struct binder_alloc *alloc);
 extern struct binder_buffer *
 binder_alloc_prepare_to_free(struct binder_alloc *alloc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/binder_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/binder_internal.h
@@ -5,6 +5,7 @@
 
 #include <linux/export.h>
 #include <linux/fs.h>
+#include <linux/kconfig.h>
 #include <linux/list.h>
 #include <linux/miscdevice.h>
 #include <linux/mutex.h>
@@ -77,7 +78,7 @@
 
 extern char *binder_devices_param;
 
-#ifdef CONFIG_ANDROID_BINDERFS
+#if IS_ENABLED(CONFIG_ANDROID_BINDERFS)
 extern bool is_binderfs_device(const struct inode *inode);
 extern struct dentry *binderfs_create_file(struct dentry *dir, const char *name,
 					   const struct file_operations *fops,
@@ -98,7 +99,7 @@
 static inline void binderfs_remove_file(struct dentry *dentry) {}
 #endif
 
-#ifdef CONFIG_ANDROID_BINDERFS
+#if IS_ENABLED(CONFIG_ANDROID_BINDERFS)
 extern int __init init_binderfs(void);
 #else
 static inline int __init init_binderfs(void)
@@ -107,41 +108,19 @@
 }
 #endif
 
-int binder_stats_show(struct seq_file *m, void *unused);
-DEFINE_SHOW_ATTRIBUTE(binder_stats);
-
-int binder_state_show(struct seq_file *m, void *unused);
-DEFINE_SHOW_ATTRIBUTE(binder_state);
+struct binder_debugfs_entry {
+	const char *name;
+	umode_t mode;
+	const struct file_operations *fops;
+	void *data;
+};
 
-int binder_transactions_show(struct seq_file *m, void *unused);
-DEFINE_SHOW_ATTRIBUTE(binder_transactions);
+extern const struct binder_debugfs_entry binder_debugfs_entries[];
 
-int binder_transaction_log_show(struct seq_file *m, void *unused);
-DEFINE_SHOW_ATTRIBUTE(binder_transaction_log);
-
-struct binder_transaction_log_entry {
-	int debug_id;
-	int debug_id_done;
-	int call_type;
-	int from_proc;
-	int from_thread;
-	int target_handle;
-	int to_proc;
-	int to_thread;
-	int to_node;
-	int data_size;
-	int offsets_size;
-	int return_error_line;
-	uint32_t return_error;
-	uint32_t return_error_param;
-	char context_name[BINDERFS_MAX_NAME + 1];
-};
-
-struct binder_transaction_log {
-	atomic_t cur;
-	bool full;
-	struct binder_transaction_log_entry entry[32];
-};
+#define binder_for_each_debugfs_entry(entry)	\
+	for ((entry) = binder_debugfs_entries;	\
+	     (entry)->name;			\
+	     (entry)++)
 
 enum binder_stat_types {
 	BINDER_STAT_PROC,
@@ -364,6 +343,9 @@
  *                        (invariant after initialized)
  * @tsk                   task_struct for group_leader of process
  *                        (invariant after initialized)
+ * @cred                  struct cred associated with the `struct file`
+ *                        in binder_open()
+ *                        (invariant after initialized)
  * @deferred_work_node:   element for binder_deferred_list
  *                        (protected by binder_deferred_lock)
  * @deferred_work:        bitmap of deferred work to perform
@@ -426,6 +408,7 @@
 	struct list_head waiting_threads;
 	int pid;
 	struct task_struct *tsk;
+	const struct cred *cred;
 	struct hlist_node deferred_work_node;
 	int deferred_work;
 	int outstanding_txns;
@@ -438,7 +421,7 @@
 	struct list_head todo;
 	struct binder_stats stats;
 	struct list_head delivered_death;
-	int max_threads;
+	u32 max_threads;
 	int requested_threads;
 	int requested_threads_started;
 	int tmp_ref;
@@ -571,6 +554,4 @@
 	};
 };
 
-extern struct binder_transaction_log binder_transaction_log;
-extern struct binder_transaction_log binder_transaction_log_failed;
 #endif /* _LINUX_BINDER_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/android/binderfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/android/binderfs.c
@@ -121,7 +121,7 @@
 	struct super_block *sb = ref_inode->i_sb;
 	struct binderfs_info *info = sb->s_fs_info;
 #if defined(CONFIG_IPC_NS)
-	bool use_reserve = (info->ipc_ns == &init_ipc_ns);
+	bool use_reserve = (info->ipc_ns == show_init_ipc_ns());
 #else
 	bool use_reserve = true;
 #endif
@@ -410,7 +410,7 @@
 	struct dentry *root = sb->s_root;
 	struct binderfs_info *info = sb->s_fs_info;
 #if defined(CONFIG_IPC_NS)
-	bool use_reserve = (info->ipc_ns == &init_ipc_ns);
+	bool use_reserve = (info->ipc_ns == show_init_ipc_ns());
 #else
 	bool use_reserve = true;
 #endif
@@ -621,6 +621,7 @@
 static int init_binder_logs(struct super_block *sb)
 {
 	struct dentry *binder_logs_root_dir, *dentry, *proc_log_dir;
+	const struct binder_debugfs_entry *db_entry;
 	struct binderfs_info *info;
 	int ret = 0;
 
@@ -631,43 +632,15 @@
 		goto out;
 	}
 
-	dentry = binderfs_create_file(binder_logs_root_dir, "stats",
-				      &binder_stats_fops, NULL);
-	if (IS_ERR(dentry)) {
-		ret = PTR_ERR(dentry);
-		goto out;
-	}
-
-	dentry = binderfs_create_file(binder_logs_root_dir, "state",
-				      &binder_state_fops, NULL);
-	if (IS_ERR(dentry)) {
-		ret = PTR_ERR(dentry);
-		goto out;
-	}
-
-	dentry = binderfs_create_file(binder_logs_root_dir, "transactions",
-				      &binder_transactions_fops, NULL);
-	if (IS_ERR(dentry)) {
-		ret = PTR_ERR(dentry);
-		goto out;
-	}
-
-	dentry = binderfs_create_file(binder_logs_root_dir,
-				      "transaction_log",
-				      &binder_transaction_log_fops,
-				      &binder_transaction_log);
-	if (IS_ERR(dentry)) {
-		ret = PTR_ERR(dentry);
-		goto out;
-	}
-
-	dentry = binderfs_create_file(binder_logs_root_dir,
-				      "failed_transaction_log",
-				      &binder_transaction_log_fops,
-				      &binder_transaction_log_failed);
-	if (IS_ERR(dentry)) {
-		ret = PTR_ERR(dentry);
-		goto out;
+	binder_for_each_debugfs_entry(db_entry) {
+		dentry = binderfs_create_file(binder_logs_root_dir,
+					      db_entry->name,
+					      db_entry->fops,
+					      db_entry->data);
+		if (IS_ERR(dentry)) {
+			ret = PTR_ERR(dentry);
+			goto out;
+		}
 	}
 
 	proc_log_dir = binderfs_create_dir(binder_logs_root_dir, "proc");
@@ -717,7 +690,7 @@
 		return -ENOMEM;
 	info = sb->s_fs_info;
 
-	info->ipc_ns = get_ipc_ns(current->nsproxy->ipc_ns);
+	info->ipc_ns = get_ipc_ns_exported(current->nsproxy->ipc_ns);
 
 	info->root_gid = make_kgid(sb->s_user_ns, 0);
 	if (!gid_valid(info->root_gid))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/acard-ahci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/acard-ahci.c
@@ -267,7 +267,7 @@
 	if (qc->tf.protocol == ATA_PROT_PIO && qc->dma_dir == DMA_FROM_DEVICE &&
 	    !(qc->flags & ATA_QCFLAG_FAILED)) {
 		ata_tf_from_fis(rx_fis + RX_FIS_PIO_SETUP, &qc->result_tf);
-		qc->result_tf.command = (rx_fis + RX_FIS_PIO_SETUP)[15];
+		qc->result_tf.status = (rx_fis + RX_FIS_PIO_SETUP)[15];
 	} else
 		ata_tf_from_fis(rx_fis + RX_FIS_D2H_REG, &qc->result_tf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci.c
@@ -49,8 +49,10 @@
 enum board_ids {
 	/* board IDs by feature in alphabetical order */
 	board_ahci,
+	board_ahci_43bit_dma,
 	board_ahci_ign_iferr,
-	board_ahci_mobile,
+	board_ahci_low_power,
+	board_ahci_no_debounce_delay,
 	board_ahci_nomsi,
 	board_ahci_noncq,
 	board_ahci_nosntf,
@@ -83,6 +85,7 @@
 static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
 static void ahci_remove_one(struct pci_dev *dev);
 static void ahci_shutdown_one(struct pci_dev *dev);
+static void ahci_intel_pcs_quirk(struct pci_dev *pdev, struct ahci_host_priv *hpriv);
 static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
 				 unsigned long deadline);
 static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
@@ -127,6 +130,13 @@
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_ops,
 	},
+	[board_ahci_43bit_dma] = {
+		AHCI_HFLAGS	(AHCI_HFLAG_43BIT_ONLY),
+		.flags		= AHCI_FLAG_COMMON,
+		.pio_mask	= ATA_PIO4,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &ahci_ops,
+	},
 	[board_ahci_ign_iferr] = {
 		AHCI_HFLAGS	(AHCI_HFLAG_IGN_IRQ_IF_ERR),
 		.flags		= AHCI_FLAG_COMMON,
@@ -134,13 +144,20 @@
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_ops,
 	},
-	[board_ahci_mobile] = {
+	[board_ahci_low_power] = {
 		AHCI_HFLAGS	(AHCI_HFLAG_IS_MOBILE),
 		.flags		= AHCI_FLAG_COMMON,
 		.pio_mask	= ATA_PIO4,
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_ops,
 	},
+	[board_ahci_no_debounce_delay] = {
+		.flags		= AHCI_FLAG_COMMON,
+		.link_flags	= ATA_LFLAG_NO_DEBOUNCE_DELAY,
+		.pio_mask	= ATA_PIO4,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &ahci_ops,
+	},
 	[board_ahci_nomsi] = {
 		AHCI_HFLAGS	(AHCI_HFLAG_NO_MSI),
 		.flags		= AHCI_FLAG_COMMON,
@@ -267,13 +284,13 @@
 	{ PCI_VDEVICE(INTEL, 0x2924), board_ahci }, /* ICH9 */
 	{ PCI_VDEVICE(INTEL, 0x2925), board_ahci }, /* ICH9 */
 	{ PCI_VDEVICE(INTEL, 0x2927), board_ahci }, /* ICH9 */
-	{ PCI_VDEVICE(INTEL, 0x2929), board_ahci_mobile }, /* ICH9M */
-	{ PCI_VDEVICE(INTEL, 0x292a), board_ahci_mobile }, /* ICH9M */
-	{ PCI_VDEVICE(INTEL, 0x292b), board_ahci_mobile }, /* ICH9M */
-	{ PCI_VDEVICE(INTEL, 0x292c), board_ahci_mobile }, /* ICH9M */
-	{ PCI_VDEVICE(INTEL, 0x292f), board_ahci_mobile }, /* ICH9M */
+	{ PCI_VDEVICE(INTEL, 0x2929), board_ahci_low_power }, /* ICH9M */
+	{ PCI_VDEVICE(INTEL, 0x292a), board_ahci_low_power }, /* ICH9M */
+	{ PCI_VDEVICE(INTEL, 0x292b), board_ahci_low_power }, /* ICH9M */
+	{ PCI_VDEVICE(INTEL, 0x292c), board_ahci_low_power }, /* ICH9M */
+	{ PCI_VDEVICE(INTEL, 0x292f), board_ahci_low_power }, /* ICH9M */
 	{ PCI_VDEVICE(INTEL, 0x294d), board_ahci }, /* ICH9 */
-	{ PCI_VDEVICE(INTEL, 0x294e), board_ahci_mobile }, /* ICH9M */
+	{ PCI_VDEVICE(INTEL, 0x294e), board_ahci_low_power }, /* ICH9M */
 	{ PCI_VDEVICE(INTEL, 0x502a), board_ahci }, /* Tolapai */
 	{ PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */
 	{ PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */
@@ -283,9 +300,9 @@
 	{ PCI_VDEVICE(INTEL, 0x3b23), board_ahci }, /* PCH AHCI */
 	{ PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */
 	{ PCI_VDEVICE(INTEL, 0x3b25), board_ahci }, /* PCH RAID */
-	{ PCI_VDEVICE(INTEL, 0x3b29), board_ahci_mobile }, /* PCH M AHCI */
+	{ PCI_VDEVICE(INTEL, 0x3b29), board_ahci_low_power }, /* PCH M AHCI */
 	{ PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */
-	{ PCI_VDEVICE(INTEL, 0x3b2c), board_ahci_mobile }, /* PCH M RAID */
+	{ PCI_VDEVICE(INTEL, 0x3b2c), board_ahci_low_power }, /* PCH M RAID */
 	{ PCI_VDEVICE(INTEL, 0x3b2f), board_ahci }, /* PCH AHCI */
 	{ PCI_VDEVICE(INTEL, 0x19b0), board_ahci_pcs7 }, /* DNV AHCI */
 	{ PCI_VDEVICE(INTEL, 0x19b1), board_ahci_pcs7 }, /* DNV AHCI */
@@ -308,9 +325,9 @@
 	{ PCI_VDEVICE(INTEL, 0x19cE), board_ahci_pcs7 }, /* DNV AHCI */
 	{ PCI_VDEVICE(INTEL, 0x19cF), board_ahci_pcs7 }, /* DNV AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1c02), board_ahci }, /* CPT AHCI */
-	{ PCI_VDEVICE(INTEL, 0x1c03), board_ahci_mobile }, /* CPT M AHCI */
+	{ PCI_VDEVICE(INTEL, 0x1c03), board_ahci_low_power }, /* CPT M AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1c04), board_ahci }, /* CPT RAID */
-	{ PCI_VDEVICE(INTEL, 0x1c05), board_ahci_mobile }, /* CPT M RAID */
+	{ PCI_VDEVICE(INTEL, 0x1c05), board_ahci_low_power }, /* CPT M RAID */
 	{ PCI_VDEVICE(INTEL, 0x1c06), board_ahci }, /* CPT RAID */
 	{ PCI_VDEVICE(INTEL, 0x1c07), board_ahci }, /* CPT RAID */
 	{ PCI_VDEVICE(INTEL, 0x1d02), board_ahci }, /* PBG AHCI */
@@ -319,29 +336,29 @@
 	{ PCI_VDEVICE(INTEL, 0x2826), board_ahci }, /* PBG RAID */
 	{ PCI_VDEVICE(INTEL, 0x2323), board_ahci }, /* DH89xxCC AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1e02), board_ahci }, /* Panther Point AHCI */
-	{ PCI_VDEVICE(INTEL, 0x1e03), board_ahci_mobile }, /* Panther M AHCI */
+	{ PCI_VDEVICE(INTEL, 0x1e03), board_ahci_low_power }, /* Panther M AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1e04), board_ahci }, /* Panther Point RAID */
 	{ PCI_VDEVICE(INTEL, 0x1e05), board_ahci }, /* Panther Point RAID */
 	{ PCI_VDEVICE(INTEL, 0x1e06), board_ahci }, /* Panther Point RAID */
-	{ PCI_VDEVICE(INTEL, 0x1e07), board_ahci_mobile }, /* Panther M RAID */
+	{ PCI_VDEVICE(INTEL, 0x1e07), board_ahci_low_power }, /* Panther M RAID */
 	{ PCI_VDEVICE(INTEL, 0x1e0e), board_ahci }, /* Panther Point RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c02), board_ahci }, /* Lynx Point AHCI */
-	{ PCI_VDEVICE(INTEL, 0x8c03), board_ahci_mobile }, /* Lynx M AHCI */
+	{ PCI_VDEVICE(INTEL, 0x8c03), board_ahci_low_power }, /* Lynx M AHCI */
 	{ PCI_VDEVICE(INTEL, 0x8c04), board_ahci }, /* Lynx Point RAID */
-	{ PCI_VDEVICE(INTEL, 0x8c05), board_ahci_mobile }, /* Lynx M RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c05), board_ahci_low_power }, /* Lynx M RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c06), board_ahci }, /* Lynx Point RAID */
-	{ PCI_VDEVICE(INTEL, 0x8c07), board_ahci_mobile }, /* Lynx M RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c07), board_ahci_low_power }, /* Lynx M RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c0e), board_ahci }, /* Lynx Point RAID */
-	{ PCI_VDEVICE(INTEL, 0x8c0f), board_ahci_mobile }, /* Lynx M RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c02), board_ahci_mobile }, /* Lynx LP AHCI */
-	{ PCI_VDEVICE(INTEL, 0x9c03), board_ahci_mobile }, /* Lynx LP AHCI */
-	{ PCI_VDEVICE(INTEL, 0x9c04), board_ahci_mobile }, /* Lynx LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c05), board_ahci_mobile }, /* Lynx LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c06), board_ahci_mobile }, /* Lynx LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c07), board_ahci_mobile }, /* Lynx LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c0e), board_ahci_mobile }, /* Lynx LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c0f), board_ahci_mobile }, /* Lynx LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9dd3), board_ahci_mobile }, /* Cannon Lake PCH-LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x8c0f), board_ahci_low_power }, /* Lynx M RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c02), board_ahci_low_power }, /* Lynx LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9c03), board_ahci_low_power }, /* Lynx LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9c04), board_ahci_low_power }, /* Lynx LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c05), board_ahci_low_power }, /* Lynx LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c06), board_ahci_low_power }, /* Lynx LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c07), board_ahci_low_power }, /* Lynx LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c0e), board_ahci_low_power }, /* Lynx LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c0f), board_ahci_low_power }, /* Lynx LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9dd3), board_ahci_low_power }, /* Cannon Lake PCH-LP AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1f22), board_ahci }, /* Avoton AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1f23), board_ahci }, /* Avoton AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1f24), board_ahci }, /* Avoton RAID */
@@ -373,26 +390,26 @@
 	{ PCI_VDEVICE(INTEL, 0x8d66), board_ahci }, /* Wellsburg RAID */
 	{ PCI_VDEVICE(INTEL, 0x8d6e), board_ahci }, /* Wellsburg RAID */
 	{ PCI_VDEVICE(INTEL, 0x23a3), board_ahci }, /* Coleto Creek AHCI */
-	{ PCI_VDEVICE(INTEL, 0x9c83), board_ahci_mobile }, /* Wildcat LP AHCI */
-	{ PCI_VDEVICE(INTEL, 0x9c85), board_ahci_mobile }, /* Wildcat LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c87), board_ahci_mobile }, /* Wildcat LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9c8f), board_ahci_mobile }, /* Wildcat LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c83), board_ahci_low_power }, /* Wildcat LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9c85), board_ahci_low_power }, /* Wildcat LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c87), board_ahci_low_power }, /* Wildcat LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c8f), board_ahci_low_power }, /* Wildcat LP RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c82), board_ahci }, /* 9 Series AHCI */
-	{ PCI_VDEVICE(INTEL, 0x8c83), board_ahci_mobile }, /* 9 Series M AHCI */
+	{ PCI_VDEVICE(INTEL, 0x8c83), board_ahci_low_power }, /* 9 Series M AHCI */
 	{ PCI_VDEVICE(INTEL, 0x8c84), board_ahci }, /* 9 Series RAID */
-	{ PCI_VDEVICE(INTEL, 0x8c85), board_ahci_mobile }, /* 9 Series M RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c85), board_ahci_low_power }, /* 9 Series M RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c86), board_ahci }, /* 9 Series RAID */
-	{ PCI_VDEVICE(INTEL, 0x8c87), board_ahci_mobile }, /* 9 Series M RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c87), board_ahci_low_power }, /* 9 Series M RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c8e), board_ahci }, /* 9 Series RAID */
-	{ PCI_VDEVICE(INTEL, 0x8c8f), board_ahci_mobile }, /* 9 Series M RAID */
-	{ PCI_VDEVICE(INTEL, 0x9d03), board_ahci_mobile }, /* Sunrise LP AHCI */
-	{ PCI_VDEVICE(INTEL, 0x9d05), board_ahci_mobile }, /* Sunrise LP RAID */
-	{ PCI_VDEVICE(INTEL, 0x9d07), board_ahci_mobile }, /* Sunrise LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c8f), board_ahci_low_power }, /* 9 Series M RAID */
+	{ PCI_VDEVICE(INTEL, 0x9d03), board_ahci_low_power }, /* Sunrise LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9d05), board_ahci_low_power }, /* Sunrise LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9d07), board_ahci_low_power }, /* Sunrise LP RAID */
 	{ PCI_VDEVICE(INTEL, 0xa102), board_ahci }, /* Sunrise Point-H AHCI */
-	{ PCI_VDEVICE(INTEL, 0xa103), board_ahci_mobile }, /* Sunrise M AHCI */
+	{ PCI_VDEVICE(INTEL, 0xa103), board_ahci_low_power }, /* Sunrise M AHCI */
 	{ PCI_VDEVICE(INTEL, 0xa105), board_ahci }, /* Sunrise Point-H RAID */
 	{ PCI_VDEVICE(INTEL, 0xa106), board_ahci }, /* Sunrise Point-H RAID */
-	{ PCI_VDEVICE(INTEL, 0xa107), board_ahci_mobile }, /* Sunrise M RAID */
+	{ PCI_VDEVICE(INTEL, 0xa107), board_ahci_low_power }, /* Sunrise M RAID */
 	{ PCI_VDEVICE(INTEL, 0xa10f), board_ahci }, /* Sunrise Point-H RAID */
 	{ PCI_VDEVICE(INTEL, 0x2822), board_ahci }, /* Lewisburg RAID*/
 	{ PCI_VDEVICE(INTEL, 0x2823), board_ahci }, /* Lewisburg AHCI*/
@@ -409,13 +426,16 @@
 	{ PCI_VDEVICE(INTEL, 0xa356), board_ahci }, /* Cannon Lake PCH-H RAID */
 	{ PCI_VDEVICE(INTEL, 0x06d7), board_ahci }, /* Comet Lake-H RAID */
 	{ PCI_VDEVICE(INTEL, 0xa386), board_ahci }, /* Comet Lake PCH-V RAID */
-	{ PCI_VDEVICE(INTEL, 0x0f22), board_ahci_mobile }, /* Bay Trail AHCI */
-	{ PCI_VDEVICE(INTEL, 0x0f23), board_ahci_mobile }, /* Bay Trail AHCI */
-	{ PCI_VDEVICE(INTEL, 0x22a3), board_ahci_mobile }, /* Cherry Tr. AHCI */
-	{ PCI_VDEVICE(INTEL, 0x5ae3), board_ahci_mobile }, /* ApolloLake AHCI */
-	{ PCI_VDEVICE(INTEL, 0x34d3), board_ahci_mobile }, /* Ice Lake LP AHCI */
-	{ PCI_VDEVICE(INTEL, 0x02d3), board_ahci_mobile }, /* Comet Lake PCH-U AHCI */
-	{ PCI_VDEVICE(INTEL, 0x02d7), board_ahci_mobile }, /* Comet Lake PCH RAID */
+	{ PCI_VDEVICE(INTEL, 0x0f22), board_ahci_low_power }, /* Bay Trail AHCI */
+	{ PCI_VDEVICE(INTEL, 0x0f23), board_ahci_low_power }, /* Bay Trail AHCI */
+	{ PCI_VDEVICE(INTEL, 0x22a3), board_ahci_low_power }, /* Cherry Tr. AHCI */
+	{ PCI_VDEVICE(INTEL, 0x5ae3), board_ahci_low_power }, /* ApolloLake AHCI */
+	{ PCI_VDEVICE(INTEL, 0x34d3), board_ahci_low_power }, /* Ice Lake LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x02d3), board_ahci_low_power }, /* Comet Lake PCH-U AHCI */
+	{ PCI_VDEVICE(INTEL, 0x02d7), board_ahci_low_power }, /* Comet Lake PCH RAID */
+	/* Elkhart Lake IDs 0x4b60 & 0x4b62 https://sata-io.org/product/8803 not tested yet */
+	{ PCI_VDEVICE(INTEL, 0x4b63), board_ahci_low_power }, /* Elkhart Lake AHCI */
+	{ PCI_VDEVICE(INTEL, 0x7ae2), board_ahci_low_power }, /* Alder Lake-P AHCI */
 
 	/* JMicron 360/1/3/5/6, match class to avoid IDE function */
 	{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -441,7 +461,9 @@
 		board_ahci_al },
 	/* AMD */
 	{ PCI_VDEVICE(AMD, 0x7800), board_ahci }, /* AMD Hudson-2 */
+	{ PCI_VDEVICE(AMD, 0x7801), board_ahci_no_debounce_delay }, /* AMD Hudson-2 (AHCI mode) */
 	{ PCI_VDEVICE(AMD, 0x7900), board_ahci }, /* AMD CZ */
+	{ PCI_VDEVICE(AMD, 0x7901), board_ahci_low_power }, /* AMD Green Sardine */
 	/* AMD is using RAID class only for ahci controllers */
 	{ PCI_VENDOR_ID_AMD, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
 	  PCI_CLASS_STORAGE_RAID << 8, 0xffffff, board_ahci },
@@ -585,11 +607,11 @@
 	{ PCI_VDEVICE(PROMISE, 0x3f20), board_ahci },	/* PDC42819 */
 	{ PCI_VDEVICE(PROMISE, 0x3781), board_ahci },   /* FastTrak TX8660 ahci-mode */
 
-	/* Asmedia */
+	/* ASMedia */
 	{ PCI_VDEVICE(ASMEDIA, 0x0601), board_ahci },	/* ASM1060 */
 	{ PCI_VDEVICE(ASMEDIA, 0x0602), board_ahci },	/* ASM1060 */
-	{ PCI_VDEVICE(ASMEDIA, 0x0611), board_ahci },	/* ASM1061 */
-	{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci },	/* ASM1062 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0611), board_ahci_43bit_dma },	/* ASM1061 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci_43bit_dma },	/* ASM1061/1062 */
 	{ PCI_VDEVICE(ASMEDIA, 0x0621), board_ahci },   /* ASM1061R */
 	{ PCI_VDEVICE(ASMEDIA, 0x0622), board_ahci },   /* ASM1062R */
 
@@ -667,6 +689,25 @@
 	ahci_save_initial_config(&pdev->dev, hpriv);
 }
 
+static int ahci_pci_reset_controller(struct ata_host *host)
+{
+	struct pci_dev *pdev = to_pci_dev(host->dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_reset_controller(host);
+	if (rc)
+		return rc;
+
+	/*
+	 * If platform firmware failed to enable ports, try to enable
+	 * them here.
+	 */
+	ahci_intel_pcs_quirk(pdev, hpriv);
+
+	return 0;
+}
+
 static void ahci_pci_init_controller(struct ata_host *host)
 {
 	struct ahci_host_priv *hpriv = host->private_data;
@@ -686,7 +727,7 @@
 
 		/* clear port IRQ */
 		tmp = readl(port_mmio + PORT_IRQ_STAT);
-		VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
+		dev_dbg(&pdev->dev, "PORT_IRQ_STAT 0x%x\n", tmp);
 		if (tmp)
 			writel(tmp, port_mmio + PORT_IRQ_STAT);
 	}
@@ -734,7 +775,7 @@
 
 	/* clear D2H reception area to properly wait for D2H FIS */
 	ata_tf_init(link->device, &tf);
-	tf.command = ATA_BUSY;
+	tf.status = ATA_BUSY;
 	ata_tf_to_fis(&tf, 0, 0, d2h_fis);
 
 	rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
@@ -805,7 +846,7 @@
 
 		/* clear D2H reception area to properly wait for D2H FIS */
 		ata_tf_init(link->device, &tf);
-		tf.command = ATA_BUSY;
+		tf.status = ATA_BUSY;
 		ata_tf_to_fis(&tf, 0, 0, d2h_fis);
 
 		rc = sata_link_hardreset(link, timing, deadline, &online,
@@ -868,7 +909,7 @@
 	struct ata_host *host = pci_get_drvdata(pdev);
 	int rc;
 
-	rc = ahci_reset_controller(host);
+	rc = ahci_pci_reset_controller(host);
 	if (rc)
 		return rc;
 	ahci_pci_init_controller(host);
@@ -903,7 +944,7 @@
 		ahci_mcp89_apple_enable(pdev);
 
 	if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
-		rc = ahci_reset_controller(host);
+		rc = ahci_pci_reset_controller(host);
 		if (rc)
 			return rc;
 
@@ -918,11 +959,20 @@
 
 #endif /* CONFIG_PM */
 
-static int ahci_configure_dma_masks(struct pci_dev *pdev, int using_dac)
+static int ahci_configure_dma_masks(struct pci_dev *pdev,
+				    struct ahci_host_priv *hpriv)
 {
-	const int dma_bits = using_dac ? 64 : 32;
+	int dma_bits;
 	int rc;
 
+	if (hpriv->cap & HOST_CAP_64) {
+		dma_bits = 64;
+		if (hpriv->flags & AHCI_HFLAG_43BIT_ONLY)
+			dma_bits = 43;
+	} else {
+		dma_bits = 32;
+	}
+
 	/*
 	 * If the device fixup already set the dma_mask to some non-standard
 	 * value, don't extend it here. This happens on STA2X11, for example.
@@ -1478,7 +1528,6 @@
 	u32 irq_stat, irq_masked;
 	unsigned int handled = 1;
 
-	VPRINTK("ENTER\n");
 	hpriv = host->private_data;
 	mmio = hpriv->mmio;
 	irq_stat = readl(mmio + HOST_IRQ_STAT);
@@ -1495,7 +1544,6 @@
 		irq_stat = readl(mmio + HOST_IRQ_STAT);
 		spin_unlock(&host->lock);
 	} while (irq_stat);
-	VPRINTK("EXIT\n");
 
 	return IRQ_RETVAL(handled);
 }
@@ -1788,12 +1836,6 @@
 	/* save initial config */
 	ahci_pci_save_initial_config(pdev, hpriv);
 
-	/*
-	 * If platform firmware failed to enable ports, try to enable
-	 * them here.
-	 */
-	ahci_intel_pcs_quirk(pdev, hpriv);
-
 	/* prepare host */
 	if (hpriv->cap & HOST_CAP_NCQ) {
 		pi.flags |= ATA_FLAG_NCQ;
@@ -1856,8 +1898,10 @@
 	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
 
 	host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
-	if (!host)
-		return -ENOMEM;
+	if (!host) {
+		rc = -ENOMEM;
+		goto err_rm_sysfs_file;
+	}
 	host->private_data = hpriv;
 
 	if (ahci_init_msi(pdev, n_ports, hpriv) < 0) {
@@ -1871,6 +1915,15 @@
 	else
 		dev_info(&pdev->dev, "SSS flag set, parallel bus scan disabled\n");
 
+	if (!(hpriv->cap & HOST_CAP_PART))
+		host->flags |= ATA_HOST_NO_PART;
+
+	if (!(hpriv->cap & HOST_CAP_SSC))
+		host->flags |= ATA_HOST_NO_SSC;
+
+	if (!(hpriv->cap2 & HOST_CAP2_SDS))
+		host->flags |= ATA_HOST_NO_DEVSLP;
+
 	if (pi.flags & ATA_FLAG_EM)
 		ahci_reset_em(host);
 
@@ -1899,13 +1952,13 @@
 	ahci_gtf_filter_workaround(host);
 
 	/* initialize adapter */
-	rc = ahci_configure_dma_masks(pdev, hpriv->cap & HOST_CAP_64);
+	rc = ahci_configure_dma_masks(pdev, hpriv);
 	if (rc)
-		return rc;
+		goto err_rm_sysfs_file;
 
-	rc = ahci_reset_controller(host);
+	rc = ahci_pci_reset_controller(host);
 	if (rc)
-		return rc;
+		goto err_rm_sysfs_file;
 
 	ahci_pci_init_controller(host);
 	ahci_pci_print_info(host);
@@ -1914,10 +1967,15 @@
 
 	rc = ahci_host_activate(host, &ahci_sht);
 	if (rc)
-		return rc;
+		goto err_rm_sysfs_file;
 
 	pm_runtime_put_noidle(&pdev->dev);
 	return 0;
+
+err_rm_sysfs_file:
+	sysfs_remove_file_from_group(&pdev->dev.kobj,
+				     &dev_attr_remapped_nvme.attr, NULL);
+	return rc;
 }
 
 static void ahci_shutdown_one(struct pci_dev *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci.h
@@ -24,6 +24,7 @@
 #include <linux/libata.h>
 #include <linux/phy/phy.h>
 #include <linux/regulator/consumer.h>
+#include <linux/bits.h>
 
 /* Enclosure Management Control */
 #define EM_CTRL_MSG_TYPE              0x000f0000
@@ -38,7 +39,6 @@
 
 enum {
 	AHCI_MAX_PORTS		= 32,
-	AHCI_MAX_CLKS		= 5,
 	AHCI_MAX_SG		= 168, /* hardware max is 64K */
 	AHCI_DMA_BOUNDARY	= 0xffffffff,
 	AHCI_MAX_CMDS		= 32,
@@ -54,12 +54,12 @@
 	AHCI_PORT_PRIV_FBS_DMA_SZ	= AHCI_CMD_SLOT_SZ +
 					  AHCI_CMD_TBL_AR_SZ +
 					  (AHCI_RX_FIS_SZ * 16),
-	AHCI_IRQ_ON_SG		= (1 << 31),
-	AHCI_CMD_ATAPI		= (1 << 5),
-	AHCI_CMD_WRITE		= (1 << 6),
-	AHCI_CMD_PREFETCH	= (1 << 7),
-	AHCI_CMD_RESET		= (1 << 8),
-	AHCI_CMD_CLR_BUSY	= (1 << 10),
+	AHCI_IRQ_ON_SG		= BIT(31),
+	AHCI_CMD_ATAPI		= BIT(5),
+	AHCI_CMD_WRITE		= BIT(6),
+	AHCI_CMD_PREFETCH	= BIT(7),
+	AHCI_CMD_RESET		= BIT(8),
+	AHCI_CMD_CLR_BUSY	= BIT(10),
 
 	RX_FIS_PIO_SETUP	= 0x20,	/* offset of PIO Setup FIS data */
 	RX_FIS_D2H_REG		= 0x40,	/* offset of D2H Register FIS data */
@@ -77,37 +77,37 @@
 	HOST_CAP2		= 0x24, /* host capabilities, extended */
 
 	/* HOST_CTL bits */
-	HOST_RESET		= (1 << 0),  /* reset controller; self-clear */
-	HOST_IRQ_EN		= (1 << 1),  /* global IRQ enable */
-	HOST_MRSM		= (1 << 2),  /* MSI Revert to Single Message */
-	HOST_AHCI_EN		= (1 << 31), /* AHCI enabled */
+	HOST_RESET		= BIT(0),  /* reset controller; self-clear */
+	HOST_IRQ_EN		= BIT(1),  /* global IRQ enable */
+	HOST_MRSM		= BIT(2),  /* MSI Revert to Single Message */
+	HOST_AHCI_EN		= BIT(31), /* AHCI enabled */
 
 	/* HOST_CAP bits */
-	HOST_CAP_SXS		= (1 << 5),  /* Supports External SATA */
-	HOST_CAP_EMS		= (1 << 6),  /* Enclosure Management support */
-	HOST_CAP_CCC		= (1 << 7),  /* Command Completion Coalescing */
-	HOST_CAP_PART		= (1 << 13), /* Partial state capable */
-	HOST_CAP_SSC		= (1 << 14), /* Slumber state capable */
-	HOST_CAP_PIO_MULTI	= (1 << 15), /* PIO multiple DRQ support */
-	HOST_CAP_FBS		= (1 << 16), /* FIS-based switching support */
-	HOST_CAP_PMP		= (1 << 17), /* Port Multiplier support */
-	HOST_CAP_ONLY		= (1 << 18), /* Supports AHCI mode only */
-	HOST_CAP_CLO		= (1 << 24), /* Command List Override support */
-	HOST_CAP_LED		= (1 << 25), /* Supports activity LED */
-	HOST_CAP_ALPM		= (1 << 26), /* Aggressive Link PM support */
-	HOST_CAP_SSS		= (1 << 27), /* Staggered Spin-up */
-	HOST_CAP_MPS		= (1 << 28), /* Mechanical presence switch */
-	HOST_CAP_SNTF		= (1 << 29), /* SNotification register */
-	HOST_CAP_NCQ		= (1 << 30), /* Native Command Queueing */
-	HOST_CAP_64		= (1 << 31), /* PCI DAC (64-bit DMA) support */
+	HOST_CAP_SXS		= BIT(5),  /* Supports External SATA */
+	HOST_CAP_EMS		= BIT(6),  /* Enclosure Management support */
+	HOST_CAP_CCC		= BIT(7),  /* Command Completion Coalescing */
+	HOST_CAP_PART		= BIT(13), /* Partial state capable */
+	HOST_CAP_SSC		= BIT(14), /* Slumber state capable */
+	HOST_CAP_PIO_MULTI	= BIT(15), /* PIO multiple DRQ support */
+	HOST_CAP_FBS		= BIT(16), /* FIS-based switching support */
+	HOST_CAP_PMP		= BIT(17), /* Port Multiplier support */
+	HOST_CAP_ONLY		= BIT(18), /* Supports AHCI mode only */
+	HOST_CAP_CLO		= BIT(24), /* Command List Override support */
+	HOST_CAP_LED		= BIT(25), /* Supports activity LED */
+	HOST_CAP_ALPM		= BIT(26), /* Aggressive Link PM support */
+	HOST_CAP_SSS		= BIT(27), /* Staggered Spin-up */
+	HOST_CAP_MPS		= BIT(28), /* Mechanical presence switch */
+	HOST_CAP_SNTF		= BIT(29), /* SNotification register */
+	HOST_CAP_NCQ		= BIT(30), /* Native Command Queueing */
+	HOST_CAP_64		= BIT(31), /* PCI DAC (64-bit DMA) support */
 
 	/* HOST_CAP2 bits */
-	HOST_CAP2_BOH		= (1 << 0),  /* BIOS/OS handoff supported */
-	HOST_CAP2_NVMHCI	= (1 << 1),  /* NVMHCI supported */
-	HOST_CAP2_APST		= (1 << 2),  /* Automatic partial to slumber */
-	HOST_CAP2_SDS		= (1 << 3),  /* Support device sleep */
-	HOST_CAP2_SADM		= (1 << 4),  /* Support aggressive DevSlp */
-	HOST_CAP2_DESO		= (1 << 5),  /* DevSlp from slumber only */
+	HOST_CAP2_BOH		= BIT(0),  /* BIOS/OS handoff supported */
+	HOST_CAP2_NVMHCI	= BIT(1),  /* NVMHCI supported */
+	HOST_CAP2_APST		= BIT(2),  /* Automatic partial to slumber */
+	HOST_CAP2_SDS		= BIT(3),  /* Support device sleep */
+	HOST_CAP2_SADM		= BIT(4),  /* Support aggressive DevSlp */
+	HOST_CAP2_DESO		= BIT(5),  /* DevSlp from slumber only */
 
 	/* registers for each SATA port */
 	PORT_LST_ADDR		= 0x00, /* command list DMA addr */
@@ -129,24 +129,24 @@
 	PORT_DEVSLP		= 0x44, /* device sleep */
 
 	/* PORT_IRQ_{STAT,MASK} bits */
-	PORT_IRQ_COLD_PRES	= (1 << 31), /* cold presence detect */
-	PORT_IRQ_TF_ERR		= (1 << 30), /* task file error */
-	PORT_IRQ_HBUS_ERR	= (1 << 29), /* host bus fatal error */
-	PORT_IRQ_HBUS_DATA_ERR	= (1 << 28), /* host bus data error */
-	PORT_IRQ_IF_ERR		= (1 << 27), /* interface fatal error */
-	PORT_IRQ_IF_NONFATAL	= (1 << 26), /* interface non-fatal error */
-	PORT_IRQ_OVERFLOW	= (1 << 24), /* xfer exhausted available S/G */
-	PORT_IRQ_BAD_PMP	= (1 << 23), /* incorrect port multiplier */
-
-	PORT_IRQ_PHYRDY		= (1 << 22), /* PhyRdy changed */
-	PORT_IRQ_DEV_ILCK	= (1 << 7), /* device interlock */
-	PORT_IRQ_CONNECT	= (1 << 6), /* port connect change status */
-	PORT_IRQ_SG_DONE	= (1 << 5), /* descriptor processed */
-	PORT_IRQ_UNK_FIS	= (1 << 4), /* unknown FIS rx'd */
-	PORT_IRQ_SDB_FIS	= (1 << 3), /* Set Device Bits FIS rx'd */
-	PORT_IRQ_DMAS_FIS	= (1 << 2), /* DMA Setup FIS rx'd */
-	PORT_IRQ_PIOS_FIS	= (1 << 1), /* PIO Setup FIS rx'd */
-	PORT_IRQ_D2H_REG_FIS	= (1 << 0), /* D2H Register FIS rx'd */
+	PORT_IRQ_COLD_PRES	= BIT(31), /* cold presence detect */
+	PORT_IRQ_TF_ERR		= BIT(30), /* task file error */
+	PORT_IRQ_HBUS_ERR	= BIT(29), /* host bus fatal error */
+	PORT_IRQ_HBUS_DATA_ERR	= BIT(28), /* host bus data error */
+	PORT_IRQ_IF_ERR		= BIT(27), /* interface fatal error */
+	PORT_IRQ_IF_NONFATAL	= BIT(26), /* interface non-fatal error */
+	PORT_IRQ_OVERFLOW	= BIT(24), /* xfer exhausted available S/G */
+	PORT_IRQ_BAD_PMP	= BIT(23), /* incorrect port multiplier */
+
+	PORT_IRQ_PHYRDY		= BIT(22), /* PhyRdy changed */
+	PORT_IRQ_DEV_ILCK	= BIT(7),  /* device interlock */
+	PORT_IRQ_CONNECT	= BIT(6),  /* port connect change status */
+	PORT_IRQ_SG_DONE	= BIT(5),  /* descriptor processed */
+	PORT_IRQ_UNK_FIS	= BIT(4),  /* unknown FIS rx'd */
+	PORT_IRQ_SDB_FIS	= BIT(3),  /* Set Device Bits FIS rx'd */
+	PORT_IRQ_DMAS_FIS	= BIT(2),  /* DMA Setup FIS rx'd */
+	PORT_IRQ_PIOS_FIS	= BIT(1),  /* PIO Setup FIS rx'd */
+	PORT_IRQ_D2H_REG_FIS	= BIT(0),  /* D2H Register FIS rx'd */
 
 	PORT_IRQ_FREEZE		= PORT_IRQ_HBUS_ERR |
 				  PORT_IRQ_IF_ERR |
@@ -162,34 +162,34 @@
 				  PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
 
 	/* PORT_CMD bits */
-	PORT_CMD_ASP		= (1 << 27), /* Aggressive Slumber/Partial */
-	PORT_CMD_ALPE		= (1 << 26), /* Aggressive Link PM enable */
-	PORT_CMD_ATAPI		= (1 << 24), /* Device is ATAPI */
-	PORT_CMD_FBSCP		= (1 << 22), /* FBS Capable Port */
-	PORT_CMD_ESP		= (1 << 21), /* External Sata Port */
-	PORT_CMD_HPCP		= (1 << 18), /* HotPlug Capable Port */
-	PORT_CMD_PMP		= (1 << 17), /* PMP attached */
-	PORT_CMD_LIST_ON	= (1 << 15), /* cmd list DMA engine running */
-	PORT_CMD_FIS_ON		= (1 << 14), /* FIS DMA engine running */
-	PORT_CMD_FIS_RX		= (1 << 4), /* Enable FIS receive DMA engine */
-	PORT_CMD_CLO		= (1 << 3), /* Command list override */
-	PORT_CMD_POWER_ON	= (1 << 2), /* Power up device */
-	PORT_CMD_SPIN_UP	= (1 << 1), /* Spin up device */
-	PORT_CMD_START		= (1 << 0), /* Enable port DMA engine */
-
-	PORT_CMD_ICC_MASK	= (0xf << 28), /* i/f ICC state mask */
-	PORT_CMD_ICC_ACTIVE	= (0x1 << 28), /* Put i/f in active state */
-	PORT_CMD_ICC_PARTIAL	= (0x2 << 28), /* Put i/f in partial state */
-	PORT_CMD_ICC_SLUMBER	= (0x6 << 28), /* Put i/f in slumber state */
+	PORT_CMD_ASP		= BIT(27), /* Aggressive Slumber/Partial */
+	PORT_CMD_ALPE		= BIT(26), /* Aggressive Link PM enable */
+	PORT_CMD_ATAPI		= BIT(24), /* Device is ATAPI */
+	PORT_CMD_FBSCP		= BIT(22), /* FBS Capable Port */
+	PORT_CMD_ESP		= BIT(21), /* External Sata Port */
+	PORT_CMD_HPCP		= BIT(18), /* HotPlug Capable Port */
+	PORT_CMD_PMP		= BIT(17), /* PMP attached */
+	PORT_CMD_LIST_ON	= BIT(15), /* cmd list DMA engine running */
+	PORT_CMD_FIS_ON		= BIT(14), /* FIS DMA engine running */
+	PORT_CMD_FIS_RX		= BIT(4),  /* Enable FIS receive DMA engine */
+	PORT_CMD_CLO		= BIT(3),  /* Command list override */
+	PORT_CMD_POWER_ON	= BIT(2),  /* Power up device */
+	PORT_CMD_SPIN_UP	= BIT(1),  /* Spin up device */
+	PORT_CMD_START		= BIT(0),  /* Enable port DMA engine */
+
+	PORT_CMD_ICC_MASK	= (0xfu << 28), /* i/f ICC state mask */
+	PORT_CMD_ICC_ACTIVE	= (0x1u << 28), /* Put i/f in active state */
+	PORT_CMD_ICC_PARTIAL	= (0x2u << 28), /* Put i/f in partial state */
+	PORT_CMD_ICC_SLUMBER	= (0x6u << 28), /* Put i/f in slumber state */
 
 	/* PORT_FBS bits */
 	PORT_FBS_DWE_OFFSET	= 16, /* FBS device with error offset */
 	PORT_FBS_ADO_OFFSET	= 12, /* FBS active dev optimization offset */
 	PORT_FBS_DEV_OFFSET	= 8,  /* FBS device to issue offset */
 	PORT_FBS_DEV_MASK	= (0xf << PORT_FBS_DEV_OFFSET),  /* FBS.DEV */
-	PORT_FBS_SDE		= (1 << 2), /* FBS single device error */
-	PORT_FBS_DEC		= (1 << 1), /* FBS device error clear */
-	PORT_FBS_EN		= (1 << 0), /* Enable FBS */
+	PORT_FBS_SDE		= BIT(2), /* FBS single device error */
+	PORT_FBS_DEC		= BIT(1), /* FBS device error clear */
+	PORT_FBS_EN		= BIT(0), /* Enable FBS */
 
 	/* PORT_DEVSLP bits */
 	PORT_DEVSLP_DM_OFFSET	= 25,             /* DITO multiplier offset */
@@ -197,52 +197,53 @@
 	PORT_DEVSLP_DITO_OFFSET	= 15,             /* DITO offset */
 	PORT_DEVSLP_MDAT_OFFSET	= 10,             /* Minimum assertion time */
 	PORT_DEVSLP_DETO_OFFSET	= 2,              /* DevSlp exit timeout */
-	PORT_DEVSLP_DSP		= (1 << 1),       /* DevSlp present */
-	PORT_DEVSLP_ADSE	= (1 << 0),       /* Aggressive DevSlp enable */
+	PORT_DEVSLP_DSP		= BIT(1),         /* DevSlp present */
+	PORT_DEVSLP_ADSE	= BIT(0),         /* Aggressive DevSlp enable */
 
 	/* hpriv->flags bits */
 
 #define AHCI_HFLAGS(flags)		.private_data	= (void *)(flags)
 
-	AHCI_HFLAG_NO_NCQ		= (1 << 0),
-	AHCI_HFLAG_IGN_IRQ_IF_ERR	= (1 << 1), /* ignore IRQ_IF_ERR */
-	AHCI_HFLAG_IGN_SERR_INTERNAL	= (1 << 2), /* ignore SERR_INTERNAL */
-	AHCI_HFLAG_32BIT_ONLY		= (1 << 3), /* force 32bit */
-	AHCI_HFLAG_MV_PATA		= (1 << 4), /* PATA port */
-	AHCI_HFLAG_NO_MSI		= (1 << 5), /* no PCI MSI */
-	AHCI_HFLAG_NO_PMP		= (1 << 6), /* no PMP */
-	AHCI_HFLAG_SECT255		= (1 << 8), /* max 255 sectors */
-	AHCI_HFLAG_YES_NCQ		= (1 << 9), /* force NCQ cap on */
-	AHCI_HFLAG_NO_SUSPEND		= (1 << 10), /* don't suspend */
-	AHCI_HFLAG_SRST_TOUT_IS_OFFLINE	= (1 << 11), /* treat SRST timeout as
-							link offline */
-	AHCI_HFLAG_NO_SNTF		= (1 << 12), /* no sntf */
-	AHCI_HFLAG_NO_FPDMA_AA		= (1 << 13), /* no FPDMA AA */
-	AHCI_HFLAG_YES_FBS		= (1 << 14), /* force FBS cap on */
-	AHCI_HFLAG_DELAY_ENGINE		= (1 << 15), /* do not start engine on
-						        port start (wait until
-						        error-handling stage) */
-	AHCI_HFLAG_NO_DEVSLP		= (1 << 17), /* no device sleep */
-	AHCI_HFLAG_NO_FBS		= (1 << 18), /* no FBS */
+	AHCI_HFLAG_NO_NCQ		= BIT(0),
+	AHCI_HFLAG_IGN_IRQ_IF_ERR	= BIT(1), /* ignore IRQ_IF_ERR */
+	AHCI_HFLAG_IGN_SERR_INTERNAL	= BIT(2), /* ignore SERR_INTERNAL */
+	AHCI_HFLAG_32BIT_ONLY		= BIT(3), /* force 32bit */
+	AHCI_HFLAG_MV_PATA		= BIT(4), /* PATA port */
+	AHCI_HFLAG_NO_MSI		= BIT(5), /* no PCI MSI */
+	AHCI_HFLAG_NO_PMP		= BIT(6), /* no PMP */
+	AHCI_HFLAG_SECT255		= BIT(8), /* max 255 sectors */
+	AHCI_HFLAG_YES_NCQ		= BIT(9), /* force NCQ cap on */
+	AHCI_HFLAG_NO_SUSPEND		= BIT(10), /* don't suspend */
+	AHCI_HFLAG_SRST_TOUT_IS_OFFLINE	= BIT(11), /* treat SRST timeout as
+						      link offline */
+	AHCI_HFLAG_NO_SNTF		= BIT(12), /* no sntf */
+	AHCI_HFLAG_NO_FPDMA_AA		= BIT(13), /* no FPDMA AA */
+	AHCI_HFLAG_YES_FBS		= BIT(14), /* force FBS cap on */
+	AHCI_HFLAG_DELAY_ENGINE		= BIT(15), /* do not start engine on
+						      port start (wait until
+						      error-handling stage) */
+	AHCI_HFLAG_NO_DEVSLP		= BIT(17), /* no device sleep */
+	AHCI_HFLAG_NO_FBS		= BIT(18), /* no FBS */
 
 #ifdef CONFIG_PCI_MSI
-	AHCI_HFLAG_MULTI_MSI		= (1 << 20), /* per-port MSI(-X) */
+	AHCI_HFLAG_MULTI_MSI		= BIT(20), /* per-port MSI(-X) */
 #else
 	/* compile out MSI infrastructure */
 	AHCI_HFLAG_MULTI_MSI		= 0,
 #endif
-	AHCI_HFLAG_WAKE_BEFORE_STOP	= (1 << 22), /* wake before DMA stop */
-	AHCI_HFLAG_YES_ALPM		= (1 << 23), /* force ALPM cap on */
-	AHCI_HFLAG_NO_WRITE_TO_RO	= (1 << 24), /* don't write to read
-							only registers */
-	AHCI_HFLAG_IS_MOBILE		= (1 << 25), /* mobile chipset, use
-							SATA_MOBILE_LPM_POLICY
-							as default lpm_policy */
-	AHCI_HFLAG_SUSPEND_PHYS		= (1 << 26), /* handle PHYs during
-							suspend/resume */
-	AHCI_HFLAG_IGN_NOTSUPP_POWER_ON	= (1 << 27), /* ignore -EOPNOTSUPP
-							from phy_power_on() */
-	AHCI_HFLAG_NO_SXS		= (1 << 28), /* SXS not supported */
+	AHCI_HFLAG_WAKE_BEFORE_STOP	= BIT(22), /* wake before DMA stop */
+	AHCI_HFLAG_YES_ALPM		= BIT(23), /* force ALPM cap on */
+	AHCI_HFLAG_NO_WRITE_TO_RO	= BIT(24), /* don't write to read
+						      only registers */
+	AHCI_HFLAG_IS_MOBILE            = BIT(25), /* mobile chipset, use
+						      SATA_MOBILE_LPM_POLICY
+						      as default lpm_policy */
+	AHCI_HFLAG_SUSPEND_PHYS		= BIT(26), /* handle PHYs during
+						      suspend/resume */
+	AHCI_HFLAG_IGN_NOTSUPP_POWER_ON	= BIT(27), /* ignore -EOPNOTSUPP
+						      from phy_power_on() */
+	AHCI_HFLAG_NO_SXS		= BIT(28), /* SXS not supported */
+	AHCI_HFLAG_43BIT_ONLY		= BIT(29), /* 43bit DMA addr limit */
 
 	/* ap->flags bits */
 
@@ -254,26 +255,26 @@
 	PCS_7				= 0x94, /* 7+ port PCS (Denverton) */
 
 	/* em constants */
-	EM_MAX_SLOTS			= 8,
+	EM_MAX_SLOTS			= SATA_PMP_MAX_PORTS,
 	EM_MAX_RETRY			= 5,
 
 	/* em_ctl bits */
-	EM_CTL_RST		= (1 << 9), /* Reset */
-	EM_CTL_TM		= (1 << 8), /* Transmit Message */
-	EM_CTL_MR		= (1 << 0), /* Message Received */
-	EM_CTL_ALHD		= (1 << 26), /* Activity LED */
-	EM_CTL_XMT		= (1 << 25), /* Transmit Only */
-	EM_CTL_SMB		= (1 << 24), /* Single Message Buffer */
-	EM_CTL_SGPIO		= (1 << 19), /* SGPIO messages supported */
-	EM_CTL_SES		= (1 << 18), /* SES-2 messages supported */
-	EM_CTL_SAFTE		= (1 << 17), /* SAF-TE messages supported */
-	EM_CTL_LED		= (1 << 16), /* LED messages supported */
+	EM_CTL_RST		= BIT(9), /* Reset */
+	EM_CTL_TM		= BIT(8), /* Transmit Message */
+	EM_CTL_MR		= BIT(0), /* Message Received */
+	EM_CTL_ALHD		= BIT(26), /* Activity LED */
+	EM_CTL_XMT		= BIT(25), /* Transmit Only */
+	EM_CTL_SMB		= BIT(24), /* Single Message Buffer */
+	EM_CTL_SGPIO		= BIT(19), /* SGPIO messages supported */
+	EM_CTL_SES		= BIT(18), /* SES-2 messages supported */
+	EM_CTL_SAFTE		= BIT(17), /* SAF-TE messages supported */
+	EM_CTL_LED		= BIT(16), /* LED messages supported */
 
 	/* em message type */
-	EM_MSG_TYPE_LED		= (1 << 0), /* LED */
-	EM_MSG_TYPE_SAFTE	= (1 << 1), /* SAF-TE */
-	EM_MSG_TYPE_SES2	= (1 << 2), /* SES-2 */
-	EM_MSG_TYPE_SGPIO	= (1 << 3), /* SGPIO */
+	EM_MSG_TYPE_LED		= BIT(0), /* LED */
+	EM_MSG_TYPE_SAFTE	= BIT(1), /* SAF-TE */
+	EM_MSG_TYPE_SES2	= BIT(2), /* SES-2 */
+	EM_MSG_TYPE_SGPIO	= BIT(3), /* SGPIO */
 };
 
 struct ahci_cmd_hdr {
@@ -341,7 +342,9 @@
 	u32			em_msg_type;	/* EM message type */
 	u32			remapped_nvme;	/* NVMe remapped device count */
 	bool			got_runtime_pm; /* Did we do pm_runtime_get? */
-	struct clk		*clks[AHCI_MAX_CLKS]; /* Optional */
+	unsigned int		n_clks;
+	struct clk_bulk_data	*clks;		/* Optional */
+	unsigned int		f_rsts;
 	struct reset_control	*rsts;		/* Optional */
 	struct regulator	**target_pwrs;	/* Optional */
 	struct regulator	*ahci_regulator;/* Optional */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_brcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_brcm.c
@@ -333,7 +333,7 @@
 
 static const struct ata_port_info ahci_brcm_port_info = {
 	.flags		= AHCI_FLAG_COMMON | ATA_FLAG_NO_DIPM,
-	.link_flags	= ATA_LFLAG_NO_DB_DELAY,
+	.link_flags	= ATA_LFLAG_NO_DEBOUNCE_DELAY,
 	.pio_mask	= ATA_PIO4,
 	.udma_mask	= ATA_UDMA6,
 	.port_ops	= &ahci_brcm_platform_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_ceva.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_ceva.c
@@ -88,7 +88,6 @@
 	u32 axicc;
 	bool is_cci_enabled;
 	int flags;
-	struct reset_control *rst;
 };
 
 static unsigned int ceva_ahci_read_id(struct ata_device *dev,
@@ -189,6 +188,60 @@
 	AHCI_SHT(DRV_NAME),
 };
 
+static int ceva_ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
+{
+	int rc, i;
+
+	rc = ahci_platform_enable_regulators(hpriv);
+	if (rc)
+		return rc;
+
+	rc = ahci_platform_enable_clks(hpriv);
+	if (rc)
+		goto disable_regulator;
+
+	/* Assert the controller reset */
+	rc = ahci_platform_assert_rsts(hpriv);
+	if (rc)
+		goto disable_clks;
+
+	for (i = 0; i < hpriv->nports; i++) {
+		rc = phy_init(hpriv->phys[i]);
+		if (rc)
+			goto disable_rsts;
+	}
+
+	/* De-assert the controller reset */
+	ahci_platform_deassert_rsts(hpriv);
+
+	for (i = 0; i < hpriv->nports; i++) {
+		rc = phy_power_on(hpriv->phys[i]);
+		if (rc) {
+			phy_exit(hpriv->phys[i]);
+			goto disable_phys;
+		}
+	}
+
+	return 0;
+
+disable_rsts:
+	ahci_platform_deassert_rsts(hpriv);
+
+disable_phys:
+	while (--i >= 0) {
+		phy_power_off(hpriv->phys[i]);
+		phy_exit(hpriv->phys[i]);
+	}
+
+disable_clks:
+	ahci_platform_disable_clks(hpriv);
+
+disable_regulator:
+	ahci_platform_disable_regulators(hpriv);
+
+	return rc;
+}
+
 static int ceva_ahci_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
@@ -203,47 +256,19 @@
 		return -ENOMEM;
 
 	cevapriv->ahci_pdev = pdev;
-
-	cevapriv->rst = devm_reset_control_get_optional_exclusive(&pdev->dev,
-								  NULL);
-	if (IS_ERR(cevapriv->rst))
-		dev_err_probe(&pdev->dev, PTR_ERR(cevapriv->rst),
-			      "failed to get reset\n");
-
 	hpriv = ahci_platform_get_resources(pdev, 0);
 	if (IS_ERR(hpriv))
 		return PTR_ERR(hpriv);
 
-	if (!cevapriv->rst) {
-		rc = ahci_platform_enable_resources(hpriv);
-		if (rc)
-			return rc;
-	} else {
-		int i;
+	hpriv->rsts = devm_reset_control_get_optional_exclusive(&pdev->dev,
+								NULL);
+	if (IS_ERR(hpriv->rsts))
+		return dev_err_probe(&pdev->dev, PTR_ERR(hpriv->rsts),
+				     "failed to get reset\n");
 
-		rc = ahci_platform_enable_clks(hpriv);
-		if (rc)
-			return rc;
-		/* Assert the controller reset */
-		reset_control_assert(cevapriv->rst);
-
-		for (i = 0; i < hpriv->nports; i++) {
-			rc = phy_init(hpriv->phys[i]);
-			if (rc)
-				return rc;
-		}
-
-		/* De-assert the controller reset */
-		reset_control_deassert(cevapriv->rst);
-
-		for (i = 0; i < hpriv->nports; i++) {
-			rc = phy_power_on(hpriv->phys[i]);
-			if (rc) {
-				phy_exit(hpriv->phys[i]);
-				return rc;
-			}
-		}
-	}
+	rc = ceva_ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
 
 	if (of_property_read_bool(np, "ceva,broken-gen2"))
 		cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
@@ -252,52 +277,60 @@
 	if (of_property_read_u8_array(np, "ceva,p0-cominit-params",
 					(u8 *)&cevapriv->pp2c[0], 4) < 0) {
 		dev_warn(dev, "ceva,p0-cominit-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	if (of_property_read_u8_array(np, "ceva,p1-cominit-params",
 					(u8 *)&cevapriv->pp2c[1], 4) < 0) {
 		dev_warn(dev, "ceva,p1-cominit-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	/* Read OOB timing value for COMWAKE from device-tree*/
 	if (of_property_read_u8_array(np, "ceva,p0-comwake-params",
 					(u8 *)&cevapriv->pp3c[0], 4) < 0) {
 		dev_warn(dev, "ceva,p0-comwake-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	if (of_property_read_u8_array(np, "ceva,p1-comwake-params",
 					(u8 *)&cevapriv->pp3c[1], 4) < 0) {
 		dev_warn(dev, "ceva,p1-comwake-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	/* Read phy BURST timing value from device-tree */
 	if (of_property_read_u8_array(np, "ceva,p0-burst-params",
 					(u8 *)&cevapriv->pp4c[0], 4) < 0) {
 		dev_warn(dev, "ceva,p0-burst-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	if (of_property_read_u8_array(np, "ceva,p1-burst-params",
 					(u8 *)&cevapriv->pp4c[1], 4) < 0) {
 		dev_warn(dev, "ceva,p1-burst-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	/* Read phy RETRY interval timing value from device-tree */
 	if (of_property_read_u16_array(np, "ceva,p0-retry-params",
 					(u16 *)&cevapriv->pp5c[0], 2) < 0) {
 		dev_warn(dev, "ceva,p0-retry-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	if (of_property_read_u16_array(np, "ceva,p1-retry-params",
 					(u16 *)&cevapriv->pp5c[1], 2) < 0) {
 		dev_warn(dev, "ceva,p1-retry-params property not defined\n");
-		return -EINVAL;
+		rc = -EINVAL;
+		goto disable_resources;
 	}
 
 	/*
@@ -335,7 +368,7 @@
 	struct ahci_host_priv *hpriv = host->private_data;
 	int rc;
 
-	rc = ahci_platform_enable_resources(hpriv);
+	rc = ceva_ahci_platform_enable_resources(hpriv);
 	if (rc)
 		return rc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_da850.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_da850.c
@@ -163,7 +163,6 @@
 	struct ahci_host_priv *hpriv;
 	void __iomem *pwrdn_reg;
 	struct resource *res;
-	struct clk *clk;
 	u32 mpy;
 	int rc;
 
@@ -172,36 +171,28 @@
 		return PTR_ERR(hpriv);
 
 	/*
-	 * Internally ahci_platform_get_resources() calls clk_get(dev, NULL)
-	 * when trying to obtain the functional clock. This SATA controller
-	 * uses two clocks for which we specify two connection ids. If we don't
-	 * have the functional clock at this point - call clk_get() again with
-	 * con_id = "fck".
+	 * Internally ahci_platform_get_resources() calls the bulk clocks
+	 * get method or falls back to using a single clk_get_optional().
+	 * This AHCI SATA controller uses two clocks: functional clock
+	 * with "fck" connection id and external reference clock with
+	 * "refclk" id. If we haven't got all of them re-try the clocks
+	 * getting procedure with the explicitly specified ids.
 	 */
-	if (!hpriv->clks[0]) {
-		clk = clk_get(dev, "fck");
-		if (IS_ERR(clk))
-			return PTR_ERR(clk);
-
-		hpriv->clks[0] = clk;
-	}
-
-	/*
-	 * The second clock used by ahci-da850 is the external REFCLK. If we
-	 * didn't get it from ahci_platform_get_resources(), let's try to
-	 * specify the con_id in clk_get().
-	 */
-	if (!hpriv->clks[1]) {
-		clk = clk_get(dev, "refclk");
-		if (IS_ERR(clk)) {
-			dev_err(dev, "unable to obtain the reference clock");
-			return -ENODEV;
-		}
-
-		hpriv->clks[1] = clk;
+	if (hpriv->n_clks < 2) {
+		hpriv->clks = devm_kcalloc(dev, 2, sizeof(*hpriv->clks), GFP_KERNEL);
+		if (!hpriv->clks)
+			return -ENOMEM;
+
+		hpriv->clks[0].id = "fck";
+		hpriv->clks[1].id = "refclk";
+		hpriv->n_clks = 2;
+
+		rc = devm_clk_bulk_get(dev, hpriv->n_clks, hpriv->clks);
+		if (rc)
+			return rc;
 	}
 
-	mpy = ahci_da850_calculate_mpy(clk_get_rate(hpriv->clks[1]));
+	mpy = ahci_da850_calculate_mpy(clk_get_rate(hpriv->clks[1].clk));
 	if (mpy == 0) {
 		dev_err(dev, "invalid REFCLK multiplier value: 0x%x", mpy);
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_dm816.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_dm816.c
@@ -69,12 +69,12 @@
 	 * keep-alive clock and the external reference clock. We need the
 	 * rate of the latter to calculate the correct value of MPY bits.
 	 */
-	if (!hpriv->clks[1]) {
+	if (hpriv->n_clks < 2) {
 		dev_err(dev, "reference clock not supplied\n");
 		return -EINVAL;
 	}
 
-	refclk_rate = clk_get_rate(hpriv->clks[1]);
+	refclk_rate = clk_get_rate(hpriv->clks[1].clk);
 	if ((refclk_rate % 100) != 0) {
 		dev_err(dev, "reference clock rate must be divisible by 100\n");
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_imx.c
@@ -1230,4 +1230,4 @@
 MODULE_DESCRIPTION("Freescale i.MX AHCI SATA platform driver");
 MODULE_AUTHOR("Richard Zhu <Hong-Xing.Zhu@freescale.com>");
 MODULE_LICENSE("GPL");
-MODULE_ALIAS("ahci:imx");
+MODULE_ALIAS("platform:" DRV_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_qoriq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_qoriq.c
@@ -125,7 +125,7 @@
 
 	/* clear D2H reception area to properly wait for D2H FIS */
 	ata_tf_init(link->device, &tf);
-	tf.command = ATA_BUSY;
+	tf.status = ATA_BUSY;
 	ata_tf_to_fis(&tf, 0, 0, d2h_fis);
 
 	rc = sata_link_hardreset(link, timing, deadline, &online,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/ahci_xgene.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/ahci_xgene.c
@@ -365,7 +365,7 @@
 	do {
 		/* clear D2H reception area to properly wait for D2H FIS */
 		ata_tf_init(link->device, &tf);
-		tf.command = ATA_BUSY;
+		tf.status = ATA_BUSY;
 		ata_tf_to_fis(&tf, 0, 0, d2h_fis);
 		rc = sata_link_hardreset(link, timing, deadline, online,
 				 ahci_check_ready);
@@ -588,8 +588,6 @@
 	void __iomem *mmio;
 	u32 irq_stat, irq_masked;
 
-	VPRINTK("ENTER\n");
-
 	hpriv = host->private_data;
 	mmio = hpriv->mmio;
 
@@ -612,8 +610,6 @@
 
 	spin_unlock(&host->lock);
 
-	VPRINTK("EXIT\n");
-
 	return IRQ_RETVAL(rc);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libahci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libahci.c
@@ -1200,6 +1200,26 @@
 	return sprintf(buf, "%d\n", emp->blink_policy);
 }
 
+static void ahci_port_clear_pending_irq(struct ata_port *ap)
+{
+	struct ahci_host_priv *hpriv = ap->host->private_data;
+	void __iomem *port_mmio = ahci_port_base(ap);
+	u32 tmp;
+
+	/* clear SError */
+	tmp = readl(port_mmio + PORT_SCR_ERR);
+	dev_dbg(ap->host->dev, "PORT_SCR_ERR 0x%x\n", tmp);
+	writel(tmp, port_mmio + PORT_SCR_ERR);
+
+	/* clear port IRQ */
+	tmp = readl(port_mmio + PORT_IRQ_STAT);
+	dev_dbg(ap->host->dev, "PORT_IRQ_STAT 0x%x\n", tmp);
+	if (tmp)
+		writel(tmp, port_mmio + PORT_IRQ_STAT);
+
+	writel(1 << ap->port_no, hpriv->mmio + HOST_IRQ_STAT);
+}
+
 static void ahci_port_init(struct device *dev, struct ata_port *ap,
 			   int port_no, void __iomem *mmio,
 			   void __iomem *port_mmio)
@@ -1214,18 +1234,7 @@
 	if (rc)
 		dev_warn(dev, "%s (%d)\n", emsg, rc);
 
-	/* clear SError */
-	tmp = readl(port_mmio + PORT_SCR_ERR);
-	VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
-	writel(tmp, port_mmio + PORT_SCR_ERR);
-
-	/* clear port IRQ */
-	tmp = readl(port_mmio + PORT_IRQ_STAT);
-	VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
-	if (tmp)
-		writel(tmp, port_mmio + PORT_IRQ_STAT);
-
-	writel(1 << port_no, mmio + HOST_IRQ_STAT);
+	ahci_port_clear_pending_irq(ap);
 
 	/* mark esata ports */
 	tmp = readl(port_mmio + PORT_CMD);
@@ -1252,10 +1261,10 @@
 	}
 
 	tmp = readl(mmio + HOST_CTL);
-	VPRINTK("HOST_CTL 0x%x\n", tmp);
+	dev_dbg(host->dev, "HOST_CTL 0x%x\n", tmp);
 	writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
 	tmp = readl(mmio + HOST_CTL);
-	VPRINTK("HOST_CTL 0x%x\n", tmp);
+	dev_dbg(host->dev, "HOST_CTL 0x%x\n", tmp);
 }
 EXPORT_SYMBOL_GPL(ahci_init_controller);
 
@@ -1552,9 +1561,11 @@
 
 	/* clear D2H reception area to properly wait for D2H FIS */
 	ata_tf_init(link->device, &tf);
-	tf.command = ATA_BUSY;
+	tf.status = ATA_BUSY;
 	ata_tf_to_fis(&tf, 0, 0, d2h_fis);
 
+	ahci_port_clear_pending_irq(ap);
+
 	rc = sata_link_hardreset(link, timing, deadline, online,
 				 ahci_check_ready);
 
@@ -1906,8 +1917,6 @@
 	void __iomem *port_mmio = ahci_port_base(ap);
 	u32 status;
 
-	VPRINTK("ENTER\n");
-
 	status = readl(port_mmio + PORT_IRQ_STAT);
 	writel(status, port_mmio + PORT_IRQ_STAT);
 
@@ -1915,8 +1924,6 @@
 	ahci_handle_port_interrupt(ap, port_mmio, status);
 	spin_unlock(ap->lock);
 
-	VPRINTK("EXIT\n");
-
 	return IRQ_HANDLED;
 }
 
@@ -1933,9 +1940,7 @@
 		ap = host->ports[i];
 		if (ap) {
 			ahci_port_intr(ap);
-			VPRINTK("port %u\n", i);
 		} else {
-			VPRINTK("port %u (no irq)\n", i);
 			if (ata_ratelimit())
 				dev_warn(host->dev,
 					 "interrupt on disabled port %u\n", i);
@@ -1956,8 +1961,6 @@
 	void __iomem *mmio;
 	u32 irq_stat, irq_masked;
 
-	VPRINTK("ENTER\n");
-
 	hpriv = host->private_data;
 	mmio = hpriv->mmio;
 
@@ -1985,8 +1988,6 @@
 
 	spin_unlock(&host->lock);
 
-	VPRINTK("EXIT\n");
-
 	return IRQ_RETVAL(rc);
 }
 
@@ -2038,7 +2039,7 @@
 	if (qc->tf.protocol == ATA_PROT_PIO && qc->dma_dir == DMA_FROM_DEVICE &&
 	    !(qc->flags & ATA_QCFLAG_FAILED)) {
 		ata_tf_from_fis(rx_fis + RX_FIS_PIO_SETUP, &qc->result_tf);
-		qc->result_tf.command = (rx_fis + RX_FIS_PIO_SETUP)[15];
+		qc->result_tf.status = (rx_fis + RX_FIS_PIO_SETUP)[15];
 	} else
 		ata_tf_from_fis(rx_fis + RX_FIS_D2H_REG, &qc->result_tf);
 
@@ -2305,6 +2306,18 @@
 EXPORT_SYMBOL_GPL(ahci_port_resume);
 
 #ifdef CONFIG_PM
+static void ahci_handle_s2idle(struct ata_port *ap)
+{
+	void __iomem *port_mmio = ahci_port_base(ap);
+	u32 devslp;
+
+	if (pm_suspend_via_firmware())
+		return;
+	devslp = readl(port_mmio + PORT_DEVSLP);
+	if ((devslp & PORT_DEVSLP_ADSE))
+		ata_msleep(ap, devslp_idle_timeout);
+}
+
 static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
 {
 	const char *emsg = NULL;
@@ -2318,6 +2331,9 @@
 		ata_port_freeze(ap);
 	}
 
+	if (acpi_storage_d3(ap->host->dev))
+		ahci_handle_s2idle(ap);
+
 	ahci_rpm_put_port(ap);
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libahci_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libahci_platform.c
@@ -97,28 +97,14 @@
  * ahci_platform_enable_clks - Enable platform clocks
  * @hpriv: host private area to store config values
  *
- * This function enables all the clks found in hpriv->clks, starting at
- * index 0. If any clk fails to enable it disables all the clks already
- * enabled in reverse order, and then returns an error.
+ * This function enables all the clks found for the AHCI device.
  *
  * RETURNS:
  * 0 on success otherwise a negative error code
  */
 int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
 {
-	int c, rc;
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
-		rc = clk_prepare_enable(hpriv->clks[c]);
-		if (rc)
-			goto disable_unprepare_clk;
-	}
-	return 0;
-
-disable_unprepare_clk:
-	while (--c >= 0)
-		clk_disable_unprepare(hpriv->clks[c]);
-	return rc;
+	return clk_bulk_prepare_enable(hpriv->n_clks, hpriv->clks);
 }
 EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
 
@@ -126,20 +112,55 @@
  * ahci_platform_disable_clks - Disable platform clocks
  * @hpriv: host private area to store config values
  *
- * This function disables all the clks found in hpriv->clks, in reverse
- * order of ahci_platform_enable_clks (starting at the end of the array).
+ * This function disables all the clocks enabled before
+ * (bulk-clocks-disable function is supposed to do that in reverse
+ * from the enabling procedure order).
  */
 void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
 {
-	int c;
-
-	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
-		if (hpriv->clks[c])
-			clk_disable_unprepare(hpriv->clks[c]);
+	clk_bulk_disable_unprepare(hpriv->n_clks, hpriv->clks);
 }
 EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
 
 /**
+ * ahci_platform_deassert_rsts - Deassert/trigger platform resets
+ * @hpriv: host private area to store config values
+ *
+ * This function deasserts or triggers all the reset lines found for
+ * the AHCI device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_deassert_rsts(struct ahci_host_priv *hpriv)
+{
+	if (hpriv->f_rsts & AHCI_PLATFORM_RST_TRIGGER)
+		return reset_control_reset(hpriv->rsts);
+
+	return reset_control_deassert(hpriv->rsts);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_deassert_rsts);
+
+/**
+ * ahci_platform_assert_rsts - Assert/rearm platform resets
+ * @hpriv: host private area to store config values
+ *
+ * This function asserts or rearms (for self-deasserting resets) all
+ * the reset controls found for the AHCI device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_assert_rsts(struct ahci_host_priv *hpriv)
+{
+	if (hpriv->f_rsts & AHCI_PLATFORM_RST_TRIGGER)
+		return reset_control_rearm(hpriv->rsts);
+
+	return reset_control_assert(hpriv->rsts);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_assert_rsts);
+
+/**
  * ahci_platform_enable_regulators - Enable regulators
  * @hpriv: host private area to store config values
  *
@@ -236,18 +257,18 @@
 	if (rc)
 		goto disable_regulator;
 
-	rc = reset_control_deassert(hpriv->rsts);
+	rc = ahci_platform_deassert_rsts(hpriv);
 	if (rc)
 		goto disable_clks;
 
 	rc = ahci_platform_enable_phys(hpriv);
 	if (rc)
-		goto disable_resets;
+		goto disable_rsts;
 
 	return 0;
 
-disable_resets:
-	reset_control_assert(hpriv->rsts);
+disable_rsts:
+	ahci_platform_assert_rsts(hpriv);
 
 disable_clks:
 	ahci_platform_disable_clks(hpriv);
@@ -274,7 +295,7 @@
 {
 	ahci_platform_disable_phys(hpriv);
 
-	reset_control_assert(hpriv->rsts);
+	ahci_platform_assert_rsts(hpriv);
 
 	ahci_platform_disable_clks(hpriv);
 
@@ -292,8 +313,6 @@
 		pm_runtime_disable(dev);
 	}
 
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
-		clk_put(hpriv->clks[c]);
 	/*
 	 * The regulators are tied to child node device and not to the
 	 * SATA device itself. So we can't use devm for automatically
@@ -374,8 +393,8 @@
  * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
  * 2) regulator for controlling the targets power (optional)
  *    regulator for controlling the AHCI controller (optional)
- * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
- *    or for non devicetree enabled platforms a single clock
+ * 3) all clocks specified in the devicetree node, or a single
+ *    clock for non-OF platforms (optional)
  * 4) resets, if flags has AHCI_PLATFORM_GET_RESETS (optional)
  * 5) phys (optional)
  *
@@ -385,11 +404,10 @@
 struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev,
 						   unsigned int flags)
 {
+	int child_nodes, rc = -ENOMEM, enabled_ports = 0;
 	struct device *dev = &pdev->dev;
 	struct ahci_host_priv *hpriv;
-	struct clk *clk;
 	struct device_node *child;
-	int i, enabled_ports = 0, rc = -ENOMEM, child_nodes;
 	u32 mask_port_map = 0;
 
 	if (!devres_open_group(dev, NULL, GFP_KERNEL))
@@ -409,25 +427,38 @@
 		goto err_out;
 	}
 
-	for (i = 0; i < AHCI_MAX_CLKS; i++) {
+	/*
+	 * Bulk clocks getting procedure can fail to find any clock due to
+	 * running on a non-OF platform or due to the clocks being defined in
+	 * bypass of the DT firmware (like da850, spear13xx). In that case we
+	 * fallback to getting a single clock source right from the dev clocks
+	 * list.
+	 */
+	rc = devm_clk_bulk_get_all(dev, &hpriv->clks);
+	if (rc < 0)
+		goto err_out;
+
+	if (rc > 0) {
+		/* Got clocks in bulk */
+		hpriv->n_clks = rc;
+	} else {
 		/*
-		 * For now we must use clk_get(dev, NULL) for the first clock,
-		 * because some platforms (da850, spear13xx) are not yet
-		 * converted to use devicetree for clocks.  For new platforms
-		 * this is equivalent to of_clk_get(dev->of_node, 0).
+		 * No clock bulk found: fallback to manually getting
+		 * the optional clock.
 		 */
-		if (i == 0)
-			clk = clk_get(dev, NULL);
-		else
-			clk = of_clk_get(dev->of_node, i);
-
-		if (IS_ERR(clk)) {
-			rc = PTR_ERR(clk);
-			if (rc == -EPROBE_DEFER)
-				goto err_out;
-			break;
+		hpriv->clks = devm_kzalloc(dev, sizeof(*hpriv->clks), GFP_KERNEL);
+		if (!hpriv->clks) {
+			rc = -ENOMEM;
+			goto err_out;
+		}
+		hpriv->clks->clk = devm_clk_get_optional(dev, NULL);
+		if (IS_ERR(hpriv->clks->clk)) {
+			rc = PTR_ERR(hpriv->clks->clk);
+			goto err_out;
+		} else if (hpriv->clks->clk) {
+			hpriv->clks->id = "ahci";
+			hpriv->n_clks = 1;
 		}
-		hpriv->clks[i] = clk;
 	}
 
 	hpriv->ahci_regulator = devm_regulator_get(dev, "ahci");
@@ -449,16 +480,28 @@
 			rc = PTR_ERR(hpriv->rsts);
 			goto err_out;
 		}
+
+		hpriv->f_rsts = flags & AHCI_PLATFORM_RST_TRIGGER;
 	}
 
-	hpriv->nports = child_nodes = of_get_child_count(dev->of_node);
+	/*
+	 * Too many sub-nodes most likely means having something wrong with
+	 * the firmware.
+	 */
+	child_nodes = of_get_child_count(dev->of_node);
+	if (child_nodes > AHCI_MAX_PORTS) {
+		rc = -EINVAL;
+		goto err_out;
+	}
 
 	/*
 	 * If no sub-node was found, we still need to set nports to
 	 * one in order to be able to use the
 	 * ahci_platform_[en|dis]able_[phys|regulators] functions.
 	 */
-	if (!child_nodes)
+	if (child_nodes)
+		hpriv->nports = child_nodes;
+	else
 		hpriv->nports = 1;
 
 	hpriv->phys = devm_kcalloc(dev, hpriv->nports, sizeof(*hpriv->phys), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-acpi.c
@@ -554,13 +554,13 @@
 
 	tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
 	tf->protocol = ATA_PROT_NODATA;
-	tf->feature = gtf->tf[0];	/* 0x1f1 */
+	tf->error   = gtf->tf[0];	/* 0x1f1 */
 	tf->nsect   = gtf->tf[1];	/* 0x1f2 */
 	tf->lbal    = gtf->tf[2];	/* 0x1f3 */
 	tf->lbam    = gtf->tf[3];	/* 0x1f4 */
 	tf->lbah    = gtf->tf[4];	/* 0x1f5 */
 	tf->device  = gtf->tf[5];	/* 0x1f6 */
-	tf->command = gtf->tf[6];	/* 0x1f7 */
+	tf->status  = gtf->tf[6];	/* 0x1f7 */
 }
 
 static int ata_acpi_filter_tf(struct ata_device *dev,
@@ -650,9 +650,7 @@
 	struct ata_taskfile *pptf = NULL;
 	struct ata_taskfile tf, ptf, rtf;
 	unsigned int err_mask;
-	const char *level;
 	const char *descr;
-	char msg[60];
 	int rc;
 
 	if ((gtf->tf[0] == 0) && (gtf->tf[1] == 0) && (gtf->tf[2] == 0)
@@ -666,6 +664,10 @@
 		pptf = &ptf;
 	}
 
+	descr = ata_get_cmd_descript(tf.command);
+	if (!descr)
+		descr = "unknown";
+
 	if (!ata_acpi_filter_tf(dev, &tf, pptf)) {
 		rtf = tf;
 		err_mask = ata_exec_internal(dev, &rtf, NULL,
@@ -673,40 +675,42 @@
 
 		switch (err_mask) {
 		case 0:
-			level = KERN_DEBUG;
-			snprintf(msg, sizeof(msg), "succeeded");
+			ata_dev_dbg(dev,
+				"ACPI cmd %02x/%02x:%02x:%02x:%02x:%02x:%02x"
+				"(%s) succeeded\n",
+				tf.command, tf.feature, tf.nsect, tf.lbal,
+				tf.lbam, tf.lbah, tf.device, descr);
 			rc = 1;
 			break;
 
 		case AC_ERR_DEV:
-			level = KERN_INFO;
-			snprintf(msg, sizeof(msg),
-				 "rejected by device (Stat=0x%02x Err=0x%02x)",
-				 rtf.command, rtf.feature);
+			ata_dev_info(dev,
+				"ACPI cmd %02x/%02x:%02x:%02x:%02x:%02x:%02x"
+				"(%s) rejected by device (Stat=0x%02x Err=0x%02x)",
+				tf.command, tf.feature, tf.nsect, tf.lbal,
+				tf.lbam, tf.lbah, tf.device, descr,
+				rtf.status, rtf.error);
 			rc = 0;
 			break;
 
 		default:
-			level = KERN_ERR;
-			snprintf(msg, sizeof(msg),
-				 "failed (Emask=0x%x Stat=0x%02x Err=0x%02x)",
-				 err_mask, rtf.command, rtf.feature);
+			ata_dev_err(dev,
+				"ACPI cmd %02x/%02x:%02x:%02x:%02x:%02x:%02x"
+				"(%s) failed (Emask=0x%x Stat=0x%02x Err=0x%02x)",
+				tf.command, tf.feature, tf.nsect, tf.lbal,
+				tf.lbam, tf.lbah, tf.device, descr,
+				err_mask, rtf.status, rtf.error);
 			rc = -EIO;
 			break;
 		}
 	} else {
-		level = KERN_INFO;
-		snprintf(msg, sizeof(msg), "filtered out");
+		ata_dev_info(dev,
+			"ACPI cmd %02x/%02x:%02x:%02x:%02x:%02x:%02x"
+			"(%s) filtered out\n",
+			tf.command, tf.feature, tf.nsect, tf.lbal,
+			tf.lbam, tf.lbah, tf.device, descr);
 		rc = 0;
 	}
-	descr = ata_get_cmd_descript(tf.command);
-
-	ata_dev_printk(dev, level,
-		       "ACPI cmd %02x/%02x:%02x:%02x:%02x:%02x:%02x (%s) %s\n",
-		       tf.command, tf.feature, tf.nsect, tf.lbal,
-		       tf.lbam, tf.lbah, tf.device,
-		       (descr ? descr : "unknown"), msg);
-
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-core.c
@@ -1185,7 +1185,7 @@
 		ata_dev_warn(dev,
 			     "failed to read native max address (err_mask=0x%x)\n",
 			     err_mask);
-		if (err_mask == AC_ERR_DEV && (tf.feature & ATA_ABORTED))
+		if (err_mask == AC_ERR_DEV && (tf.error & ATA_ABORTED))
 			return -EACCES;
 		return -EIO;
 	}
@@ -1249,7 +1249,7 @@
 			     "failed to set max address (err_mask=0x%x)\n",
 			     err_mask);
 		if (err_mask == AC_ERR_DEV &&
-		    (tf.feature & (ATA_ABORTED | ATA_IDNF)))
+		    (tf.error & (ATA_ABORTED | ATA_IDNF)))
 			return -EACCES;
 		return -EIO;
 	}
@@ -1616,7 +1616,7 @@
 
 	/* perform minimal error analysis */
 	if (qc->flags & ATA_QCFLAG_FAILED) {
-		if (qc->result_tf.command & (ATA_ERR | ATA_DF))
+		if (qc->result_tf.status & (ATA_ERR | ATA_DF))
 			qc->err_mask |= AC_ERR_DEV;
 
 		if (!qc->err_mask)
@@ -1625,7 +1625,7 @@
 		if (qc->err_mask & ~AC_ERR_OTHER)
 			qc->err_mask &= ~AC_ERR_OTHER;
 	} else if (qc->tf.command == ATA_CMD_REQ_SENSE_DATA) {
-		qc->result_tf.command |= ATA_SENSE;
+		qc->result_tf.status |= ATA_SENSE;
 	}
 
 	/* finish up */
@@ -1848,7 +1848,7 @@
 			return 0;
 		}
 
-		if ((err_mask == AC_ERR_DEV) && (tf.feature & ATA_ABORTED)) {
+		if ((err_mask == AC_ERR_DEV) && (tf.error & ATA_ABORTED)) {
 			/* Device or controller might have reported
 			 * the wrong device class.  Give a shot at the
 			 * other IDENTIFY if the current one is
@@ -2007,7 +2007,7 @@
 
 retry:
 	ata_tf_init(dev, &tf);
-	if (dev->dma_mode && ata_id_has_read_log_dma_ext(dev->id) &&
+	if (ata_dma_enabled(dev) && ata_id_has_read_log_dma_ext(dev->id) &&
 	    !(dev->horkage & ATA_HORKAGE_NO_DMA_LOG)) {
 		tf.command = ATA_CMD_READ_LOG_DMA_EXT;
 		tf.protocol = ATA_PROT_DMA;
@@ -2031,8 +2031,9 @@
 			dev->horkage |= ATA_HORKAGE_NO_DMA_LOG;
 			goto retry;
 		}
-		ata_dev_err(dev, "Read log page 0x%02x failed, Emask 0x%x\n",
-			    (unsigned int)page, err_mask);
+		ata_dev_err(dev,
+			    "Read log 0x%02x page 0x%02x failed, Emask 0x%x\n",
+			    (unsigned int)log, (unsigned int)page, err_mask);
 	}
 
 	return err_mask;
@@ -2166,6 +2167,9 @@
 	struct ata_port *ap = dev->link->ap;
 	unsigned int err_mask;
 
+	if (!ata_identify_page_supported(dev, ATA_LOG_SATA_SETTINGS))
+		return;
+
 	err_mask = ata_read_log_page(dev,
 				     ATA_LOG_IDENTIFY_DEVICE,
 				     ATA_LOG_SATA_SETTINGS,
@@ -2378,7 +2382,7 @@
 	struct ata_port *ap = dev->link->ap;
 	const u16 *id = dev->id;
 	const char *lba_desc;
-	char ncq_desc[24];
+	char ncq_desc[32];
 	int ret;
 
 	dev->flags |= ATA_DFLAG_LBA;
@@ -2442,7 +2446,8 @@
 	 * Check device sleep capability. Get DevSlp timing variables
 	 * from SATA Settings page of Identify Device Data Log.
 	 */
-	if (!ata_id_has_devslp(dev->id))
+	if (!ata_id_has_devslp(dev->id) ||
+	    !ata_identify_page_supported(dev, ATA_LOG_SATA_SETTINGS))
 		return;
 
 	err_mask = ata_read_log_page(dev,
@@ -3071,7 +3076,7 @@
 	 */
 	if (spd > 1)
 		mask &= (1 << (spd - 1)) - 1;
-	else
+	else if (link->sata_spd)
 		return -EINVAL;
 
 	/* were we already at the bottom? */
@@ -3851,6 +3856,8 @@
 	{ "VRFDFC22048UCHC-TE*", NULL,		ATA_HORKAGE_NODMA },
 	/* Odd clown on sil3726/4726 PMPs */
 	{ "Config  Disk",	NULL,		ATA_HORKAGE_DISABLE },
+	/* Similar story with ASMedia 1092 */
+	{ "ASMT109x- Config",	NULL,		ATA_HORKAGE_DISABLE },
 
 	/* Weird ATAPI devices */
 	{ "TORiSAN DVD-ROM DRD-N216", NULL,	ATA_HORKAGE_MAX_SEC_128 },
@@ -3954,6 +3961,10 @@
 	{ "PIONEER DVD-RW  DVR-212D",	NULL,	ATA_HORKAGE_NOSETXFER },
 	{ "PIONEER DVD-RW  DVR-216D",	NULL,	ATA_HORKAGE_NOSETXFER },
 
+	/* These specific Pioneer models have LPM issues */
+	{ "PIONEER BD-RW   BDR-207M",	NULL,	ATA_HORKAGE_NOLPM },
+	{ "PIONEER BD-RW   BDR-205",	NULL,	ATA_HORKAGE_NOLPM },
+
 	/* Crucial BX100 SSD 500GB has broken LPM support */
 	{ "CT500BX100SSD1",		NULL,	ATA_HORKAGE_NOLPM },
 
@@ -3992,6 +4003,9 @@
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "Crucial_CT*MX100*",		"MU01",	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
+	{ "Samsung SSD 840 EVO*",	NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+						ATA_HORKAGE_NO_DMA_LOG |
+						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "Samsung SSD 840*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "Samsung SSD 850*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
@@ -4007,6 +4021,7 @@
 
 	/* devices that don't properly handle TRIM commands */
 	{ "SuperSSpeed S238*",		NULL,	ATA_HORKAGE_NOTRIM, },
+	{ "M88V29*",			NULL,	ATA_HORKAGE_NOTRIM, },
 
 	/*
 	 * As defined, the DRAT (Deterministic Read After Trim) and RZAT
@@ -4356,7 +4371,7 @@
 	/* A clean abort indicates an original or just out of spec drive
 	   and we should continue as we issue the setup based on the
 	   drive reported working geometry */
-	if (err_mask == AC_ERR_DEV && (tf.feature & ATA_ABORTED))
+	if (err_mask == AC_ERR_DEV && (tf.error & ATA_ABORTED))
 		err_mask = 0;
 
 	DPRINTK("EXIT, err_mask=%x\n", err_mask);
@@ -4984,17 +4999,19 @@
 	struct ata_link *link;
 	unsigned long flags;
 
-	/* Previous resume operation might still be in
-	 * progress.  Wait for PM_PENDING to clear.
+	spin_lock_irqsave(ap->lock, flags);
+
+	/*
+	 * A previous PM operation might still be in progress. Wait for
+	 * ATA_PFLAG_PM_PENDING to clear.
 	 */
 	if (ap->pflags & ATA_PFLAG_PM_PENDING) {
+		spin_unlock_irqrestore(ap->lock, flags);
 		ata_port_wait_eh(ap);
-		WARN_ON(ap->pflags & ATA_PFLAG_PM_PENDING);
+		spin_lock_irqsave(ap->lock, flags);
 	}
 
-	/* request PM ops to EH */
-	spin_lock_irqsave(ap->lock, flags);
-
+	/* Request PM operation to EH */
 	ap->pm_mesg = mesg;
 	ap->pflags |= ATA_PFLAG_PM_PENDING;
 	ata_for_each_link(link, ap, HOST_FIRST) {
@@ -5006,10 +5023,8 @@
 
 	spin_unlock_irqrestore(ap->lock, flags);
 
-	if (!async) {
+	if (!async)
 		ata_port_wait_eh(ap);
-		WARN_ON(ap->pflags & ATA_PFLAG_PM_PENDING);
-	}
 }
 
 /*
@@ -5177,7 +5192,7 @@
 #endif
 
 const struct device_type ata_port_type = {
-	.name = "ata_port",
+	.name = ATA_PORT_TYPE_NAME,
 #ifdef CONFIG_PM
 	.pm = &ata_port_pm_ops,
 #endif
@@ -5328,7 +5343,7 @@
 
 	mutex_init(&ap->scsi_scan_mutex);
 	INIT_DELAYED_WORK(&ap->hotplug_task, ata_scsi_hotplug);
-	INIT_WORK(&ap->scsi_rescan_task, ata_scsi_dev_rescan);
+	INIT_DELAYED_WORK(&ap->scsi_rescan_task, ata_scsi_dev_rescan);
 	INIT_LIST_HEAD(&ap->eh_done_q);
 	init_waitqueue_head(&ap->eh_wait_q);
 	init_completion(&ap->park_req_pending);
@@ -5376,6 +5391,9 @@
 	for (i = 0; i < host->n_ports; i++) {
 		struct ata_port *ap = host->ports[i];
 
+		if (!ap)
+			continue;
+
 		kfree(ap->pmp_link);
 		kfree(ap->slave_link);
 		kfree(ap);
@@ -5430,12 +5448,16 @@
 	if (!host)
 		return NULL;
 
-	if (!devres_open_group(dev, NULL, GFP_KERNEL))
-		goto err_free;
+	if (!devres_open_group(dev, NULL, GFP_KERNEL)) {
+		kfree(host);
+		return NULL;
+	}
 
 	dr = devres_alloc(ata_devres_release, 0, GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		kfree(host);
 		goto err_out;
+	}
 
 	devres_add(dev, dr);
 	dev_set_drvdata(dev, host);
@@ -5463,8 +5485,6 @@
 
  err_out:
 	devres_release_group(dev, NULL);
- err_free:
-	kfree(host);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(ata_host_alloc);
@@ -5489,7 +5509,7 @@
 				      const struct ata_port_info * const * ppi,
 				      int n_ports)
 {
-	const struct ata_port_info *pi;
+	const struct ata_port_info *pi = &ata_dummy_port_info;
 	struct ata_host *host;
 	int i, j;
 
@@ -5497,7 +5517,7 @@
 	if (!host)
 		return NULL;
 
-	for (i = 0, j = 0, pi = NULL; i < host->n_ports; i++) {
+	for (i = 0, j = 0; i < host->n_ports; i++) {
 		struct ata_port *ap = host->ports[i];
 
 		if (ppi[j])
@@ -5925,11 +5945,30 @@
 	if (!ap->ops->error_handler)
 		goto skip_eh;
 
-	/* tell EH we're leaving & flush EH */
+	/* Wait for any ongoing EH */
+	ata_port_wait_eh(ap);
+
+	mutex_lock(&ap->scsi_scan_mutex);
 	spin_lock_irqsave(ap->lock, flags);
+
+	/* Remove scsi devices */
+	ata_for_each_link(link, ap, HOST_FIRST) {
+		ata_for_each_dev(dev, link, ALL) {
+			if (dev->sdev) {
+				spin_unlock_irqrestore(ap->lock, flags);
+				scsi_remove_device(dev->sdev);
+				spin_lock_irqsave(ap->lock, flags);
+				dev->sdev = NULL;
+			}
+		}
+	}
+
+	/* Tell EH to disable all devices */
 	ap->pflags |= ATA_PFLAG_UNLOADING;
 	ata_port_schedule_eh(ap);
+
 	spin_unlock_irqrestore(ap->lock, flags);
+	mutex_unlock(&ap->scsi_scan_mutex);
 
 	/* wait till EH commits suicide */
 	ata_port_wait_eh(ap);
@@ -5938,6 +5977,7 @@
 	WARN_ON(!(ap->pflags & ATA_PFLAG_UNLOADED));
 
 	cancel_delayed_work_sync(&ap->hotplug_task);
+	cancel_delayed_work_sync(&ap->scsi_rescan_task);
 
  skip_eh:
 	/* clean up zpodd on port removal */
@@ -6482,67 +6522,6 @@
 };
 EXPORT_SYMBOL_GPL(ata_dummy_port_info);
 
-/*
- * Utility print functions
- */
-void ata_port_printk(const struct ata_port *ap, const char *level,
-		     const char *fmt, ...)
-{
-	struct va_format vaf;
-	va_list args;
-
-	va_start(args, fmt);
-
-	vaf.fmt = fmt;
-	vaf.va = &args;
-
-	printk("%sata%u: %pV", level, ap->print_id, &vaf);
-
-	va_end(args);
-}
-EXPORT_SYMBOL(ata_port_printk);
-
-void ata_link_printk(const struct ata_link *link, const char *level,
-		     const char *fmt, ...)
-{
-	struct va_format vaf;
-	va_list args;
-
-	va_start(args, fmt);
-
-	vaf.fmt = fmt;
-	vaf.va = &args;
-
-	if (sata_pmp_attached(link->ap) || link->ap->slave_link)
-		printk("%sata%u.%02u: %pV",
-		       level, link->ap->print_id, link->pmp, &vaf);
-	else
-		printk("%sata%u: %pV",
-		       level, link->ap->print_id, &vaf);
-
-	va_end(args);
-}
-EXPORT_SYMBOL(ata_link_printk);
-
-void ata_dev_printk(const struct ata_device *dev, const char *level,
-		    const char *fmt, ...)
-{
-	struct va_format vaf;
-	va_list args;
-
-	va_start(args, fmt);
-
-	vaf.fmt = fmt;
-	vaf.va = &args;
-
-	printk("%sata%u.%02u: %pV",
-	       level, dev->link->ap->print_id, dev->link->pmp + dev->devno,
-	       &vaf);
-
-	va_end(args);
-}
-EXPORT_SYMBOL(ata_dev_printk);
-
 void ata_print_version(const struct device *dev, const char *version)
 {
 	dev_printk(KERN_DEBUG, dev, "version %s\n", version);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-eh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-eh.c
@@ -93,6 +93,12 @@
 	ULONG_MAX,
 };
 
+static const unsigned long ata_eh_revalidate_timeouts[] = {
+	15000,	/* Some drives are slow to read log pages when waking-up */
+	15000,  /* combined time till here is enough even for media access */
+	ULONG_MAX,
+};
+
 static const unsigned long ata_eh_flush_timeouts[] = {
 	15000,	/* be generous with flush */
 	15000,  /* ditto */
@@ -129,6 +135,8 @@
 ata_eh_cmd_timeout_table[ATA_EH_CMD_TIMEOUT_TABLE_SIZE] = {
 	{ .commands = CMDS(ATA_CMD_ID_ATA, ATA_CMD_ID_ATAPI),
 	  .timeouts = ata_eh_identify_timeouts, },
+	{ .commands = CMDS(ATA_CMD_READ_LOG_EXT, ATA_CMD_READ_LOG_DMA_EXT),
+	  .timeouts = ata_eh_revalidate_timeouts, },
 	{ .commands = CMDS(ATA_CMD_READ_NATIVE_MAX, ATA_CMD_READ_NATIVE_MAX_EXT),
 	  .timeouts = ata_eh_other_timeouts, },
 	{ .commands = CMDS(ATA_CMD_SET_MAX, ATA_CMD_SET_MAX_EXT),
@@ -1378,7 +1386,7 @@
 
 	err_mask = ata_exec_internal(dev, &tf, cdb, DMA_NONE, NULL, 0, 0);
 	if (err_mask == AC_ERR_DEV)
-		*r_sense_key = tf.feature >> 4;
+		*r_sense_key = tf.error >> 4;
 	return err_mask;
 }
 
@@ -1423,12 +1431,12 @@
 
 	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
 	/* Ignore err_mask; ATA_ERR might be set */
-	if (tf.command & ATA_SENSE) {
+	if (tf.status & ATA_SENSE) {
 		ata_scsi_set_sense(dev, cmd, tf.lbah, tf.lbam, tf.lbal);
 		qc->flags |= ATA_QCFLAG_SENSE_VALID;
 	} else {
 		ata_dev_warn(dev, "request sense failed stat %02x emask %x\n",
-			     tf.command, err_mask);
+			     tf.status, err_mask);
 	}
 }
 
@@ -1553,7 +1561,7 @@
 				      const struct ata_taskfile *tf)
 {
 	unsigned int tmp, action = 0;
-	u8 stat = tf->command, err = tf->feature;
+	u8 stat = tf->status, err = tf->error;
 
 	if ((stat & (ATA_BUSY | ATA_DRQ | ATA_DRDY)) != ATA_DRDY) {
 		qc->err_mask |= AC_ERR_HSM;
@@ -1590,7 +1598,7 @@
 		if (!(qc->ap->pflags & ATA_PFLAG_FROZEN)) {
 			tmp = atapi_eh_request_sense(qc->dev,
 						qc->scsicmd->sense_buffer,
-						qc->result_tf.feature >> 4);
+						qc->result_tf.error >> 4);
 			if (!tmp)
 				qc->flags |= ATA_QCFLAG_SENSE_VALID;
 			else
@@ -2122,6 +2130,7 @@
 		{ ATA_CMD_WRITE_QUEUED_FUA_EXT, "WRITE DMA QUEUED FUA EXT" },
 		{ ATA_CMD_FPDMA_READ,		"READ FPDMA QUEUED" },
 		{ ATA_CMD_FPDMA_WRITE,		"WRITE FPDMA QUEUED" },
+		{ ATA_CMD_NCQ_NON_DATA,		"NCQ NON-DATA" },
 		{ ATA_CMD_FPDMA_SEND,		"SEND FPDMA QUEUED" },
 		{ ATA_CMD_FPDMA_RECV,		"RECEIVE FPDMA QUEUED" },
 		{ ATA_CMD_PIO_READ,		"READ SECTOR(S)" },
@@ -2214,7 +2223,7 @@
 	struct ata_eh_context *ehc = &link->eh_context;
 	struct ata_queued_cmd *qc;
 	const char *frozen, *desc;
-	char tries_buf[6] = "";
+	char tries_buf[16] = "";
 	int tag, nr_failed = 0;
 
 	if (ehc->i.flags & ATA_EHI_QUIET)
@@ -2363,7 +2372,7 @@
 			cmd->hob_feature, cmd->hob_nsect,
 			cmd->hob_lbal, cmd->hob_lbam, cmd->hob_lbah,
 			cmd->device, qc->tag, data_buf, cdb_buf,
-			res->command, res->feature, res->nsect,
+			res->status, res->error, res->nsect,
 			res->lbal, res->lbam, res->lbah,
 			res->hob_feature, res->hob_nsect,
 			res->hob_lbal, res->hob_lbam, res->hob_lbah,
@@ -2371,28 +2380,28 @@
 			qc->err_mask & AC_ERR_NCQ ? " <F>" : "");
 
 #ifdef CONFIG_ATA_VERBOSE_ERROR
-		if (res->command & (ATA_BUSY | ATA_DRDY | ATA_DF | ATA_DRQ |
-				    ATA_SENSE | ATA_ERR)) {
-			if (res->command & ATA_BUSY)
+		if (res->status & (ATA_BUSY | ATA_DRDY | ATA_DF | ATA_DRQ |
+				   ATA_SENSE | ATA_ERR)) {
+			if (res->status & ATA_BUSY)
 				ata_dev_err(qc->dev, "status: { Busy }\n");
 			else
 				ata_dev_err(qc->dev, "status: { %s%s%s%s%s}\n",
-				  res->command & ATA_DRDY ? "DRDY " : "",
-				  res->command & ATA_DF ? "DF " : "",
-				  res->command & ATA_DRQ ? "DRQ " : "",
-				  res->command & ATA_SENSE ? "SENSE " : "",
-				  res->command & ATA_ERR ? "ERR " : "");
+				  res->status & ATA_DRDY ? "DRDY " : "",
+				  res->status & ATA_DF ? "DF " : "",
+				  res->status & ATA_DRQ ? "DRQ " : "",
+				  res->status & ATA_SENSE ? "SENSE " : "",
+				  res->status & ATA_ERR ? "ERR " : "");
 		}
 
 		if (cmd->command != ATA_CMD_PACKET &&
-		    (res->feature & (ATA_ICRC | ATA_UNC | ATA_AMNF |
-				     ATA_IDNF | ATA_ABORTED)))
+		    (res->error & (ATA_ICRC | ATA_UNC | ATA_AMNF | ATA_IDNF |
+				   ATA_ABORTED)))
 			ata_dev_err(qc->dev, "error: { %s%s%s%s%s}\n",
-			  res->feature & ATA_ICRC ? "ICRC " : "",
-			  res->feature & ATA_UNC ? "UNC " : "",
-			  res->feature & ATA_AMNF ? "AMNF " : "",
-			  res->feature & ATA_IDNF ? "IDNF " : "",
-			  res->feature & ATA_ABORTED ? "ABRT " : "");
+				    res->error & ATA_ICRC ? "ICRC " : "",
+				    res->error & ATA_UNC ? "UNC " : "",
+				    res->error & ATA_AMNF ? "AMNF " : "",
+				    res->error & ATA_IDNF ? "IDNF " : "",
+				    res->error & ATA_ABORTED ? "ABRT " : "");
 #endif
 	}
 }
@@ -2694,18 +2703,11 @@
 			postreset(slave, classes);
 	}
 
-	/*
-	 * Some controllers can't be frozen very well and may set spurious
-	 * error conditions during reset.  Clear accumulated error
-	 * information and re-thaw the port if frozen.  As reset is the
-	 * final recovery action and we cross check link onlineness against
-	 * device classification later, no hotplug event is lost by this.
-	 */
+	/* clear cached SError */
 	spin_lock_irqsave(link->ap->lock, flags);
-	memset(&link->eh_info, 0, sizeof(link->eh_info));
+	link->eh_info.serror = 0;
 	if (slave)
-		memset(&slave->eh_info, 0, sizeof(link->eh_info));
-	ap->pflags &= ~ATA_PFLAG_EH_PENDING;
+		slave->eh_info.serror = 0;
 	spin_unlock_irqrestore(link->ap->lock, flags);
 
 	if (ap->pflags & ATA_PFLAG_FROZEN)
@@ -2948,7 +2950,7 @@
 			ehc->i.flags |= ATA_EHI_SETMODE;
 
 			/* schedule the scsi_rescan_device() here */
-			schedule_work(&(ap->scsi_rescan_task));
+			schedule_delayed_work(&ap->scsi_rescan_task, 0);
 		} else if (dev->class == ATA_DEV_UNKNOWN &&
 			   ehc->tries[dev->devno] &&
 			   ata_class_enabled(ehc->classes[dev->devno])) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-sata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-sata.c
@@ -191,8 +191,8 @@
 
 void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf)
 {
-	tf->command	= fis[2];	/* status */
-	tf->feature	= fis[3];	/* error */
+	tf->status	= fis[2];
+	tf->error	= fis[3];
 
 	tf->lbal	= fis[4];
 	tf->lbam	= fis[5];
@@ -317,7 +317,7 @@
 		 * immediately after resuming.  Delay 200ms before
 		 * debouncing.
 		 */
-		if (!(link->flags & ATA_LFLAG_NO_DB_DELAY))
+		if (!(link->flags & ATA_LFLAG_NO_DEBOUNCE_DELAY))
 			ata_msleep(link->ap, 200);
 
 		/* is SControl restored correctly? */
@@ -394,10 +394,23 @@
 	case ATA_LPM_MED_POWER_WITH_DIPM:
 	case ATA_LPM_MIN_POWER_WITH_PARTIAL:
 	case ATA_LPM_MIN_POWER:
-		if (ata_link_nr_enabled(link) > 0)
-			/* no restrictions on LPM transitions */
+		if (ata_link_nr_enabled(link) > 0) {
+			/* assume no restrictions on LPM transitions */
 			scontrol &= ~(0x7 << 8);
-		else {
+
+			/*
+			 * If the controller does not support partial, slumber,
+			 * or devsleep, then disallow these transitions.
+			 */
+			if (link->ap->host->flags & ATA_HOST_NO_PART)
+				scontrol |= (0x1 << 8);
+
+			if (link->ap->host->flags & ATA_HOST_NO_SSC)
+				scontrol |= (0x2 << 8);
+
+			if (link->ap->host->flags & ATA_HOST_NO_DEVSLP)
+				scontrol |= (0x4 << 8);
+		} else {
 			/* empty port, power off */
 			scontrol &= ~0xf;
 			scontrol |= (0x1 << 2);
@@ -1402,8 +1415,8 @@
 
 	*tag = buf[0] & 0x1f;
 
-	tf->command = buf[2];
-	tf->feature = buf[3];
+	tf->status = buf[2];
+	tf->error = buf[3];
 	tf->lbal = buf[4];
 	tf->lbam = buf[5];
 	tf->lbah = buf[6];
@@ -1413,7 +1426,8 @@
 	tf->hob_lbah = buf[10];
 	tf->nsect = buf[12];
 	tf->hob_nsect = buf[13];
-	if (dev->class == ATA_DEV_ZAC && ata_id_has_ncq_autosense(dev->id))
+	if (dev->class == ATA_DEV_ZAC && ata_id_has_ncq_autosense(dev->id) &&
+	    (tf->status & ATA_SENSE))
 		tf->auxiliary = buf[14] << 16 | buf[15] << 8 | buf[16];
 
 	return 0;
@@ -1477,8 +1491,12 @@
 	memcpy(&qc->result_tf, &tf, sizeof(tf));
 	qc->result_tf.flags = ATA_TFLAG_ISADDR | ATA_TFLAG_LBA | ATA_TFLAG_LBA48;
 	qc->err_mask |= AC_ERR_DEV | AC_ERR_NCQ;
-	if (dev->class == ATA_DEV_ZAC &&
-	    ((qc->result_tf.command & ATA_SENSE) || qc->result_tf.auxiliary)) {
+
+	/*
+	 * If the device supports NCQ autosense, ata_eh_read_log_10h() will have
+	 * stored the sense data in qc->result_tf.auxiliary.
+	 */
+	if (qc->result_tf.auxiliary) {
 		char sense_key, asc, ascq;
 
 		sense_key = (qc->result_tf.auxiliary >> 16) & 0xff;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-scsi.c
@@ -671,7 +671,7 @@
  */
 static void ata_dump_status(unsigned id, struct ata_taskfile *tf)
 {
-	u8 stat = tf->command, err = tf->feature;
+	u8 stat = tf->status, err = tf->error;
 
 	pr_warn("ata%u: status=0x%02x { ", id, stat);
 	if (stat & ATA_BUSY) {
@@ -867,14 +867,22 @@
 	 * onto sense key, asc & ascq.
 	 */
 	if (qc->err_mask ||
-	    tf->command & (ATA_BUSY | ATA_DF | ATA_ERR | ATA_DRQ)) {
-		ata_to_sense_error(qc->ap->print_id, tf->command, tf->feature,
+	    tf->status & (ATA_BUSY | ATA_DF | ATA_ERR | ATA_DRQ)) {
+		ata_to_sense_error(qc->ap->print_id, tf->status, tf->error,
 				   &sense_key, &asc, &ascq, verbose);
 		ata_scsi_set_sense(qc->dev, cmd, sense_key, asc, ascq);
 	} else {
 		/*
 		 * ATA PASS-THROUGH INFORMATION AVAILABLE
-		 * Always in descriptor format sense.
+		 *
+		 * Note: we are supposed to call ata_scsi_set_sense(), which
+		 * respects the D_SENSE bit, instead of unconditionally
+		 * generating the sense data in descriptor format. However,
+		 * because hdparm, hddtemp, and udisks incorrectly assume sense
+		 * data in descriptor format, without even looking at the
+		 * RESPONSE CODE field in the returned sense data (to see which
+		 * format the returned sense data is in), we are stuck with
+		 * being bug compatible with older kernels.
 		 */
 		scsi_build_sense(cmd, 1, RECOVERED_ERROR, 0, 0x1D);
 	}
@@ -897,13 +905,13 @@
 		 * Copy registers into sense buffer.
 		 */
 		desc[2] = 0x00;
-		desc[3] = tf->feature;	/* == error reg */
+		desc[3] = tf->error;
 		desc[5] = tf->nsect;
 		desc[7] = tf->lbal;
 		desc[9] = tf->lbam;
 		desc[11] = tf->lbah;
 		desc[12] = tf->device;
-		desc[13] = tf->command; /* == status reg */
+		desc[13] = tf->status;
 
 		/*
 		 * Fill in Extend bit, and the high order bytes
@@ -918,8 +926,8 @@
 		}
 	} else {
 		/* Fixed sense format */
-		desc[0] = tf->feature;
-		desc[1] = tf->command; /* status */
+		desc[0] = tf->error;
+		desc[1] = tf->status;
 		desc[2] = tf->device;
 		desc[3] = tf->nsect;
 		desc[7] = 0;
@@ -968,14 +976,14 @@
 	 * onto sense key, asc & ascq.
 	 */
 	if (qc->err_mask ||
-	    tf->command & (ATA_BUSY | ATA_DF | ATA_ERR | ATA_DRQ)) {
-		ata_to_sense_error(qc->ap->print_id, tf->command, tf->feature,
+	    tf->status & (ATA_BUSY | ATA_DF | ATA_ERR | ATA_DRQ)) {
+		ata_to_sense_error(qc->ap->print_id, tf->status, tf->error,
 				   &sense_key, &asc, &ascq, verbose);
 		ata_scsi_set_sense(dev, cmd, sense_key, asc, ascq);
 	} else {
 		/* Could not decode error */
 		ata_dev_warn(dev, "could not decode error status 0x%x err_mask 0x%x\n",
-			     tf->command, qc->err_mask);
+			     tf->status, qc->err_mask);
 		ata_scsi_set_sense(dev, cmd, ABORTED_COMMAND, 0, 0);
 		return;
 	}
@@ -2490,7 +2498,7 @@
 
 	/* fill these in, for the case where they are -not- overwritten */
 	cmd->sense_buffer[0] = 0x70;
-	cmd->sense_buffer[2] = qc->tf.feature >> 4;
+	cmd->sense_buffer[2] = qc->tf.error >> 4;
 
 	ata_qc_reinit(qc);
 
@@ -2698,18 +2706,36 @@
 	return 0;
 }
 
-static struct ata_device *ata_find_dev(struct ata_port *ap, int devno)
+static struct ata_device *ata_find_dev(struct ata_port *ap, unsigned int devno)
 {
-	if (!sata_pmp_attached(ap)) {
-		if (likely(devno >= 0 &&
-			   devno < ata_link_max_devices(&ap->link)))
+	/*
+	 * For the non-PMP case, ata_link_max_devices() returns 1 (SATA case),
+	 * or 2 (IDE master + slave case). However, the former case includes
+	 * libsas hosted devices which are numbered per scsi host, leading
+	 * to devno potentially being larger than 0 but with each struct
+	 * ata_device having its own struct ata_port and struct ata_link.
+	 * To accommodate these, ignore devno and always use device number 0.
+	 */
+	if (likely(!sata_pmp_attached(ap))) {
+		int link_max_devices = ata_link_max_devices(&ap->link);
+
+		if (link_max_devices == 1)
+			return &ap->link.device[0];
+
+		if (devno < link_max_devices)
 			return &ap->link.device[devno];
-	} else {
-		if (likely(devno >= 0 &&
-			   devno < ap->nr_pmp_links))
-			return &ap->pmp_link[devno].device[0];
+
+		return NULL;
 	}
 
+	/*
+	 * For PMP-attached devices, the device number corresponds to C
+	 * (channel) of SCSI [H:C:I:L], indicating the port pmp link
+	 * for the device.
+	 */
+	if (devno < ap->nr_pmp_links)
+		return &ap->pmp_link[devno].device[0];
+
 	return NULL;
 }
 
@@ -2826,8 +2852,19 @@
 		goto invalid_fld;
 	}
 
-	if (ata_is_ncq(tf->protocol) && (cdb[2 + cdb_offset] & 0x3) == 0)
-		tf->protocol = ATA_PROT_NCQ_NODATA;
+	if ((cdb[2 + cdb_offset] & 0x3) == 0) {
+		/*
+		 * When T_LENGTH is zero (No data is transferred), dir should
+		 * be DMA_NONE.
+		 */
+		if (scmd->sc_data_direction != DMA_NONE) {
+			fp = 2 + cdb_offset;
+			goto invalid_fld;
+		}
+
+		if (ata_is_ncq(tf->protocol))
+			tf->protocol = ATA_PROT_NCQ_NODATA;
+	}
 
 	/* enable LBA */
 	tf->flags |= ATA_TFLAG_LBA;
@@ -3248,6 +3285,7 @@
 	case REPORT_LUNS:
 	case REQUEST_SENSE:
 	case SYNCHRONIZE_CACHE:
+	case SYNCHRONIZE_CACHE_16:
 	case REZERO_UNIT:
 	case SEEK_6:
 	case SEEK_10:
@@ -3914,6 +3952,7 @@
 		return ata_scsi_write_same_xlat;
 
 	case SYNCHRONIZE_CACHE:
+	case SYNCHRONIZE_CACHE_16:
 		if (ata_try_flush_cache(dev))
 			return ata_scsi_flush_xlat;
 		break;
@@ -3975,44 +4014,51 @@
 
 int __ata_scsi_queuecmd(struct scsi_cmnd *scmd, struct ata_device *dev)
 {
+	struct ata_port *ap = dev->link->ap;
 	u8 scsi_op = scmd->cmnd[0];
 	ata_xlat_func_t xlat_func;
-	int rc = 0;
+
+	/*
+	 * scsi_queue_rq() will defer commands if scsi_host_in_recovery().
+	 * However, this check is done without holding the ap->lock (a libata
+	 * specific lock), so we can have received an error irq since then,
+	 * therefore we must check if EH is pending, while holding ap->lock.
+	 */
+	if (ap->pflags & (ATA_PFLAG_EH_PENDING | ATA_PFLAG_EH_IN_PROGRESS))
+		return SCSI_MLQUEUE_DEVICE_BUSY;
+
+	if (unlikely(!scmd->cmd_len))
+		goto bad_cdb_len;
 
 	if (dev->class == ATA_DEV_ATA || dev->class == ATA_DEV_ZAC) {
-		if (unlikely(!scmd->cmd_len || scmd->cmd_len > dev->cdb_len))
+		if (unlikely(scmd->cmd_len > dev->cdb_len))
 			goto bad_cdb_len;
 
 		xlat_func = ata_get_xlat_func(dev, scsi_op);
-	} else {
-		if (unlikely(!scmd->cmd_len))
+	} else if (likely((scsi_op != ATA_16) || !atapi_passthru16)) {
+		/* relay SCSI command to ATAPI device */
+		int len = COMMAND_SIZE(scsi_op);
+
+		if (unlikely(len > scmd->cmd_len ||
+			     len > dev->cdb_len ||
+			     scmd->cmd_len > ATAPI_CDB_LEN))
 			goto bad_cdb_len;
 
-		xlat_func = NULL;
-		if (likely((scsi_op != ATA_16) || !atapi_passthru16)) {
-			/* relay SCSI command to ATAPI device */
-			int len = COMMAND_SIZE(scsi_op);
-			if (unlikely(len > scmd->cmd_len ||
-				     len > dev->cdb_len ||
-				     scmd->cmd_len > ATAPI_CDB_LEN))
-				goto bad_cdb_len;
-
-			xlat_func = atapi_xlat;
-		} else {
-			/* ATA_16 passthru, treat as an ATA command */
-			if (unlikely(scmd->cmd_len > 16))
-				goto bad_cdb_len;
+		xlat_func = atapi_xlat;
+	} else {
+		/* ATA_16 passthru, treat as an ATA command */
+		if (unlikely(scmd->cmd_len > 16))
+			goto bad_cdb_len;
 
-			xlat_func = ata_get_xlat_func(dev, scsi_op);
-		}
+		xlat_func = ata_get_xlat_func(dev, scsi_op);
 	}
 
 	if (xlat_func)
-		rc = ata_scsi_translate(dev, scmd, xlat_func);
-	else
-		ata_scsi_simulate(dev, scmd);
+		return ata_scsi_translate(dev, scmd, xlat_func);
 
-	return rc;
+	ata_scsi_simulate(dev, scmd);
+
+	return 0;
 
  bad_cdb_len:
 	DPRINTK("bad CDB len=%u, scsi_op=0x%02x, max=%u\n",
@@ -4159,6 +4205,7 @@
 	 * turning this into a no-op.
 	 */
 	case SYNCHRONIZE_CACHE:
+	case SYNCHRONIZE_CACHE_16:
 		fallthrough;
 
 	/* no-op's, complete with success */
@@ -4175,7 +4222,7 @@
 		break;
 
 	case MAINTENANCE_IN:
-		if (scsicmd[1] == MI_REPORT_SUPPORTED_OPERATION_CODES)
+		if ((scsicmd[1] & 0x1f) == MI_REPORT_SUPPORTED_OPERATION_CODES)
 			ata_scsi_rbuf_fill(&args, ata_scsiop_maint_in);
 		else
 			ata_scsi_set_invalid_field(dev, cmd, 1, 0xff);
@@ -4588,10 +4635,11 @@
 void ata_scsi_dev_rescan(struct work_struct *work)
 {
 	struct ata_port *ap =
-		container_of(work, struct ata_port, scsi_rescan_task);
+		container_of(work, struct ata_port, scsi_rescan_task.work);
 	struct ata_link *link;
 	struct ata_device *dev;
 	unsigned long flags;
+	bool delay_rescan = false;
 
 	mutex_lock(&ap->scsi_scan_mutex);
 	spin_lock_irqsave(ap->lock, flags);
@@ -4605,6 +4653,21 @@
 			if (scsi_device_get(sdev))
 				continue;
 
+			/*
+			 * If the rescan work was scheduled because of a resume
+			 * event, the port is already fully resumed, but the
+			 * SCSI device may not yet be fully resumed. In such
+			 * case, executing scsi_rescan_device() may cause a
+			 * deadlock with the PM code on device_lock(). Prevent
+			 * this by giving up and retrying rescan after a short
+			 * delay.
+			 */
+			delay_rescan = sdev->sdev_gendev.power.is_suspended;
+			if (delay_rescan) {
+				scsi_device_put(sdev);
+				break;
+			}
+
 			spin_unlock_irqrestore(ap->lock, flags);
 			scsi_rescan_device(&(sdev->sdev_gendev));
 			scsi_device_put(sdev);
@@ -4614,4 +4677,8 @@
 
 	spin_unlock_irqrestore(ap->lock, flags);
 	mutex_unlock(&ap->scsi_scan_mutex);
+
+	if (delay_rescan)
+		schedule_delayed_work(&ap->scsi_rescan_task,
+				      msecs_to_jiffies(5));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-sff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-sff.c
@@ -457,8 +457,8 @@
 {
 	struct ata_ioports *ioaddr = &ap->ioaddr;
 
-	tf->command = ata_sff_check_status(ap);
-	tf->feature = ioread8(ioaddr->error_addr);
+	tf->status = ata_sff_check_status(ap);
+	tf->error = ioread8(ioaddr->error_addr);
 	tf->nsect = ioread8(ioaddr->nsect_addr);
 	tf->lbal = ioread8(ioaddr->lbal_addr);
 	tf->lbam = ioread8(ioaddr->lbam_addr);
@@ -1837,7 +1837,7 @@
 	memset(&tf, 0, sizeof(tf));
 
 	ap->ops->sff_tf_read(ap, &tf);
-	err = tf.feature;
+	err = tf.error;
 	if (r_err)
 		*r_err = err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata-transport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata-transport.c
@@ -196,7 +196,7 @@
 	{ XFER_PIO_0,			"XFER_PIO_0" },
 	{ XFER_PIO_SLOW,		"XFER_PIO_SLOW" }
 };
-ata_bitfield_name_match(xfer,ata_xfer_names)
+ata_bitfield_name_search(xfer, ata_xfer_names)
 
 /*
  * ATA Port attributes
@@ -266,6 +266,10 @@
 	put_device(dev);
 }
 
+static const struct device_type ata_port_sas_type = {
+	.name = ATA_PORT_TYPE_NAME,
+};
+
 /** ata_tport_add - initialize a transport ATA port structure
  *
  * @parent:	parent device
@@ -283,7 +287,10 @@
 	struct device *dev = &ap->tdev;
 
 	device_initialize(dev);
-	dev->type = &ata_port_type;
+	if (ap->flags & ATA_FLAG_SAS_HOST)
+		dev->type = &ata_port_sas_type;
+	else
+		dev->type = &ata_port_type;
 
 	dev->parent = parent;
 	ata_host_get(ap->host);
@@ -301,7 +308,9 @@
 	pm_runtime_enable(dev);
 	pm_runtime_forbid(dev);
 
-	transport_add_device(dev);
+	error = transport_add_device(dev);
+	if (error)
+		goto tport_transport_add_err;
 	transport_configure_device(dev);
 
 	error = ata_tlink_add(&ap->link);
@@ -312,12 +321,12 @@
 
  tport_link_err:
 	transport_remove_device(dev);
+ tport_transport_add_err:
 	device_del(dev);
 
  tport_err:
 	transport_destroy_device(dev);
 	put_device(dev);
-	ata_host_put(ap->host);
 	return error;
 }
 
@@ -426,7 +435,9 @@
 		goto tlink_err;
 	}
 
-	transport_add_device(dev);
+	error = transport_add_device(dev);
+	if (error)
+		goto tlink_transport_err;
 	transport_configure_device(dev);
 
 	ata_for_each_dev(ata_dev, link, ALL) {
@@ -441,6 +452,7 @@
 		ata_tdev_delete(ata_dev);
 	}
 	transport_remove_device(dev);
+  tlink_transport_err:
 	device_del(dev);
   tlink_err:
 	transport_destroy_device(dev);
@@ -678,7 +690,13 @@
 		return error;
 	}
 
-	transport_add_device(dev);
+	error = transport_add_device(dev);
+	if (error) {
+		device_del(dev);
+		ata_tdev_free(ata_dev);
+		return error;
+	}
+
 	transport_configure_device(dev);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/libata.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/libata.h
@@ -30,6 +30,8 @@
 	ATA_DNXFER_QUIET	= (1 << 31),
 };
 
+#define ATA_PORT_TYPE_NAME	"ata_port"
+
 extern atomic_t ata_print_id;
 extern int atapi_passthru16;
 extern int libata_fua;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_arasan_cf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_arasan_cf.c
@@ -528,7 +528,8 @@
 	/* dma_request_channel may sleep, so calling from process context */
 	acdev->dma_chan = dma_request_chan(acdev->host->dev, "data");
 	if (IS_ERR(acdev->dma_chan)) {
-		dev_err(acdev->host->dev, "Unable to get dma_chan\n");
+		dev_err_probe(acdev->host->dev, PTR_ERR(acdev->dma_chan),
+			      "Unable to get dma_chan\n");
 		acdev->dma_chan = NULL;
 		goto chan_request_fail;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_ep93xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_ep93xx.c
@@ -416,8 +416,8 @@
 {
 	struct ep93xx_pata_data *drv_data = ap->host->private_data;
 
-	tf->command = ep93xx_pata_check_status(ap);
-	tf->feature = ep93xx_pata_read_reg(drv_data, IDECTRL_ADDR_FEATURE);
+	tf->status = ep93xx_pata_check_status(ap);
+	tf->error = ep93xx_pata_read_reg(drv_data, IDECTRL_ADDR_FEATURE);
 	tf->nsect = ep93xx_pata_read_reg(drv_data, IDECTRL_ADDR_NSECT);
 	tf->lbal = ep93xx_pata_read_reg(drv_data, IDECTRL_ADDR_LBAL);
 	tf->lbam = ep93xx_pata_read_reg(drv_data, IDECTRL_ADDR_LBAM);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_falcon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_falcon.c
@@ -123,8 +123,8 @@
 	struct resource *base_res, *ctl_res, *irq_res;
 	struct ata_host *host;
 	struct ata_port *ap;
-	void __iomem *base;
-	int irq = 0;
+	void __iomem *base, *ctl_base;
+	int irq = 0, io_offset = 1, reg_shift = 2; /* Falcon defaults */
 
 	dev_info(&pdev->dev, "Atari Falcon and Q40/Q60 PATA controller\n");
 
@@ -165,26 +165,34 @@
 	ap->pio_mask = ATA_PIO4;
 	ap->flags |= ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_IORDY;
 
-	base = (void __iomem *)base_mem_res->start;
 	/* N.B. this assumes data_addr will be used for word-sized I/O only */
-	ap->ioaddr.data_addr		= base + 0 + 0 * 4;
-	ap->ioaddr.error_addr		= base + 1 + 1 * 4;
-	ap->ioaddr.feature_addr		= base + 1 + 1 * 4;
-	ap->ioaddr.nsect_addr		= base + 1 + 2 * 4;
-	ap->ioaddr.lbal_addr		= base + 1 + 3 * 4;
-	ap->ioaddr.lbam_addr		= base + 1 + 4 * 4;
-	ap->ioaddr.lbah_addr		= base + 1 + 5 * 4;
-	ap->ioaddr.device_addr		= base + 1 + 6 * 4;
-	ap->ioaddr.status_addr		= base + 1 + 7 * 4;
-	ap->ioaddr.command_addr		= base + 1 + 7 * 4;
-
-	base = (void __iomem *)ctl_mem_res->start;
-	ap->ioaddr.altstatus_addr	= base + 1;
-	ap->ioaddr.ctl_addr		= base + 1;
-
-	ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
-		      (unsigned long)base_mem_res->start,
-		      (unsigned long)ctl_mem_res->start);
+	ap->ioaddr.data_addr = (void __iomem *)base_mem_res->start;
+
+	if (base_res) {		/* only Q40 has IO resources */
+		io_offset = 0x10000;
+		reg_shift = 0;
+		base = (void __iomem *)base_res->start;
+		ctl_base = (void __iomem *)ctl_res->start;
+	} else {
+		base = (void __iomem *)base_mem_res->start;
+		ctl_base = (void __iomem *)ctl_mem_res->start;
+	}
+
+	ap->ioaddr.error_addr	= base + io_offset + (1 << reg_shift);
+	ap->ioaddr.feature_addr	= base + io_offset + (1 << reg_shift);
+	ap->ioaddr.nsect_addr	= base + io_offset + (2 << reg_shift);
+	ap->ioaddr.lbal_addr	= base + io_offset + (3 << reg_shift);
+	ap->ioaddr.lbam_addr	= base + io_offset + (4 << reg_shift);
+	ap->ioaddr.lbah_addr	= base + io_offset + (5 << reg_shift);
+	ap->ioaddr.device_addr	= base + io_offset + (6 << reg_shift);
+	ap->ioaddr.status_addr	= base + io_offset + (7 << reg_shift);
+	ap->ioaddr.command_addr	= base + io_offset + (7 << reg_shift);
+
+	ap->ioaddr.altstatus_addr	= ctl_base + io_offset;
+	ap->ioaddr.ctl_addr		= ctl_base + io_offset;
+
+	ata_port_desc(ap, "cmd %px ctl %px data %px",
+		      base, ctl_base, ap->ioaddr.data_addr);
 
 	irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (irq_res && irq_res->start > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_ftide010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_ftide010.c
@@ -570,6 +570,7 @@
 };
 module_platform_driver(pata_ftide010_driver);
 
+MODULE_DESCRIPTION("low level driver for Faraday Technology FTIDE010");
 MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:" DRV_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_hpt37x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_hpt37x.c
@@ -920,6 +920,20 @@
 	pci_write_config_byte(dev, 0x5a, irqmask);
 
 	/*
+	 * HPT371 chips physically have only one channel, the secondary one,
+	 * but the primary channel registers do exist!  Go figure...
+	 * So,  we manually disable the non-existing channel here
+	 * (if the BIOS hasn't done this already).
+	 */
+	if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
+		u8 mcr1;
+
+		pci_read_config_byte(dev, 0x50, &mcr1);
+		mcr1 &= ~0x04;
+		pci_write_config_byte(dev, 0x50, mcr1);
+	}
+
+	/*
 	 * default to pci clock. make sure MA15/16 are set to output
 	 * to prevent drives having problems with 40-pin cables. Needed
 	 * for some drives such as IBM-DTLA which will not enter ready
@@ -950,14 +964,14 @@
 
 	if ((freq >> 12) != 0xABCDE) {
 		int i;
-		u8 sr;
+		u16 sr;
 		u32 total = 0;
 
 		pr_warn("BIOS has not set timing clocks\n");
 
 		/* This is the process the HPT371 BIOS is reported to use */
 		for (i = 0; i < 128; i++) {
-			pci_read_config_byte(dev, 0x78, &sr);
+			pci_read_config_word(dev, 0x78, &sr);
 			total += sr & 0x1FF;
 			udelay(15);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_isapnp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_isapnp.c
@@ -82,6 +82,9 @@
 	if (pnp_port_valid(idev, 1)) {
 		ctl_addr = devm_ioport_map(&idev->dev,
 					   pnp_port_start(idev, 1), 1);
+		if (!ctl_addr)
+			return -ENOMEM;
+
 		ap->ioaddr.altstatus_addr = ctl_addr;
 		ap->ioaddr.ctl_addr = ctl_addr;
 		ap->ops = &isapnp_port_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_ixp4xx_cf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_ixp4xx_cf.c
@@ -114,7 +114,7 @@
 {
 	struct ixp4xx_pata *ixpp = ap->host->private_data;
 
-	ata_dev_printk(adev, KERN_INFO, "configured for PIO%d 8bit\n",
+	ata_dev_info(adev, "configured for PIO%d 8bit\n",
 		       adev->pio_mode - XFER_PIO_0);
 	ixp4xx_set_8bit_timing(ixpp, adev->pio_mode);
 }
@@ -132,8 +132,8 @@
 	struct ixp4xx_pata *ixpp = ap->host->private_data;
 	unsigned long flags;
 
-	ata_dev_printk(adev, KERN_DEBUG, "%s %d bytes\n", (rw == READ) ? "READ" : "WRITE",
-		       buflen);
+	ata_dev_dbg(adev, "%s %d bytes\n", (rw == READ) ? "READ" : "WRITE",
+		    buflen);
 	spin_lock_irqsave(ap->lock, flags);
 
 	/* set the expansion bus in 16bit mode and restore
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_legacy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_legacy.c
@@ -173,8 +173,6 @@
 static struct legacy_probe probe_list[NR_HOST];
 static struct legacy_data legacy_data[NR_HOST];
 static struct ata_host *legacy_host[NR_HOST];
-static int nr_legacy_host;
-
 
 /**
  *	legacy_probe_add	-	Add interface to probe list
@@ -315,9 +313,10 @@
 	outb(inb(0x1F4) & 0x07, 0x1F4);
 
 	rt = inb(0x1F3);
-	rt &= 0x07 << (3 * adev->devno);
+	rt &= ~(0x07 << (3 * !adev->devno));
 	if (pio)
-		rt |= (1 + 3 * pio) << (3 * adev->devno);
+		rt |= (1 + 3 * pio) << (3 * !adev->devno);
+	outb(rt, 0x1F3);
 
 	udelay(100);
 	outb(inb(0x1F2) | 0x01, 0x1F2);
@@ -1275,9 +1274,11 @@
 {
 	int i;
 
-	for (i = 0; i < nr_legacy_host; i++) {
+	for (i = 0; i < NR_HOST; i++) {
 		struct legacy_data *ld = &legacy_data[i];
-		ata_host_detach(legacy_host[i]);
+
+		if (legacy_host[i])
+			ata_host_detach(legacy_host[i]);
 		platform_device_unregister(ld->platform_dev);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_macio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_macio.c
@@ -540,7 +540,8 @@
 
 		while (sg_len) {
 			/* table overflow should never happen */
-			BUG_ON (pi++ >= MAX_DCMDS);
+			if (WARN_ON_ONCE(pi >= MAX_DCMDS))
+				return AC_ERR_SYSTEM;
 
 			len = (sg_len < MAX_DBDMA_SEG) ? sg_len : MAX_DBDMA_SEG;
 			table->command = cpu_to_le16(write ? OUTPUT_MORE: INPUT_MORE);
@@ -552,11 +553,13 @@
 			addr += len;
 			sg_len -= len;
 			++table;
+			++pi;
 		}
 	}
 
 	/* Should never happen according to Tejun */
-	BUG_ON(!pi);
+	if (WARN_ON_ONCE(!pi))
+		return AC_ERR_SYSTEM;
 
 	/* Convert the last command to an input/output */
 	table--;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_marvell.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_marvell.c
@@ -83,6 +83,8 @@
 	switch(ap->port_no)
 	{
 	case 0:
+		if (!ap->ioaddr.bmdma_addr)
+			return ATA_CBL_PATA_UNK;
 		if (ioread8(ap->ioaddr.bmdma_addr + 1) & 1)
 			return ATA_CBL_PATA40;
 		return ATA_CBL_PATA80;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_ns87415.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_ns87415.c
@@ -260,12 +260,12 @@
  *	LOCKING:
  *	Inherited from caller.
  */
-void ns87560_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+static void ns87560_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
 {
 	struct ata_ioports *ioaddr = &ap->ioaddr;
 
-	tf->command = ns87560_check_status(ap);
-	tf->feature = ioread8(ioaddr->error_addr);
+	tf->status = ns87560_check_status(ap);
+	tf->error = ioread8(ioaddr->error_addr);
 	tf->nsect = ioread8(ioaddr->nsect_addr);
 	tf->lbal = ioread8(ioaddr->lbal_addr);
 	tf->lbam = ioread8(ioaddr->lbam_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_octeon_cf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_octeon_cf.c
@@ -386,7 +386,7 @@
 	void __iomem *base = ap->ioaddr.data_addr;
 
 	blob = __raw_readw(base + 0xc);
-	tf->feature = blob >> 8;
+	tf->error = blob >> 8;
 
 	blob = __raw_readw(base + 2);
 	tf->nsect = blob & 0xff;
@@ -398,7 +398,7 @@
 
 	blob = __raw_readw(base + 6);
 	tf->device = blob & 0xff;
-	tf->command = blob >> 8;
+	tf->status = blob >> 8;
 
 	if (tf->flags & ATA_TFLAG_LBA48) {
 		if (likely(ap->ioaddr.ctl_addr)) {
@@ -888,12 +888,14 @@
 				int i;
 				res_dma = platform_get_resource(dma_dev, IORESOURCE_MEM, 0);
 				if (!res_dma) {
+					put_device(&dma_dev->dev);
 					of_node_put(dma_node);
 					return -EINVAL;
 				}
 				cf_port->dma_base = (u64)devm_ioremap(&pdev->dev, res_dma->start,
 									 resource_size(res_dma));
 				if (!cf_port->dma_base) {
+					put_device(&dma_dev->dev);
 					of_node_put(dma_node);
 					return -EINVAL;
 				}
@@ -903,6 +905,7 @@
 					irq = i;
 					irq_handler = octeon_cf_interrupt;
 				}
+				put_device(&dma_dev->dev);
 			}
 			of_node_put(dma_node);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/pata_samsung_cf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/pata_samsung_cf.c
@@ -213,7 +213,7 @@
 {
 	struct ata_ioports *ioaddr = &ap->ioaddr;
 
-	tf->feature = ata_inb(ap->host, ioaddr->error_addr);
+	tf->error = ata_inb(ap->host, ioaddr->error_addr);
 	tf->nsect = ata_inb(ap->host, ioaddr->nsect_addr);
 	tf->lbal = ata_inb(ap->host, ioaddr->lbal_addr);
 	tf->lbam = ata_inb(ap->host, ioaddr->lbam_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_dwc_460ex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_dwc_460ex.c
@@ -145,7 +145,11 @@
 #endif
 };
 
-#define SATA_DWC_QCMD_MAX	32
+/*
+ * Allow one extra special slot for commands and DMA management
+ * to account for libata internal commands.
+ */
+#define SATA_DWC_QCMD_MAX	(ATA_MAX_QUEUE + 1)
 
 struct sata_dwc_device_port {
 	struct sata_dwc_device	*hsdev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_fsl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_fsl.c
@@ -1394,6 +1394,14 @@
 	return 0;
 }
 
+static void sata_fsl_host_stop(struct ata_host *host)
+{
+        struct sata_fsl_host_priv *host_priv = host->private_data;
+
+        iounmap(host_priv->hcr_base);
+        kfree(host_priv);
+}
+
 /*
  * scsi mid-layer and libata interface structures
  */
@@ -1426,6 +1434,8 @@
 	.port_start = sata_fsl_port_start,
 	.port_stop = sata_fsl_port_stop,
 
+	.host_stop      = sata_fsl_host_stop,
+
 	.pmp_attach = sata_fsl_pmp_attach,
 	.pmp_detach = sata_fsl_pmp_detach,
 };
@@ -1480,9 +1490,9 @@
 	host_priv->ssr_base = ssr_base;
 	host_priv->csr_base = csr_base;
 
-	irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
-	if (!irq) {
-		dev_err(&ofdev->dev, "invalid irq from platform\n");
+	irq = platform_get_irq(ofdev, 0);
+	if (irq < 0) {
+		retval = irq;
 		goto error_exit_with_cleanup;
 	}
 	host_priv->irq = irq;
@@ -1557,10 +1567,6 @@
 
 	ata_host_detach(host);
 
-	irq_dispose_mapping(host_priv->irq);
-	iounmap(host_priv->hcr_base);
-	kfree(host_priv);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_gemini.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_gemini.c
@@ -201,7 +201,10 @@
 		pclk = sg->sata0_pclk;
 	else
 		pclk = sg->sata1_pclk;
-	clk_enable(pclk);
+	ret = clk_enable(pclk);
+	if (ret)
+		return ret;
+
 	msleep(10);
 
 	/* Do not keep clocking a bridge that is not online */
@@ -435,6 +438,7 @@
 };
 module_platform_driver(gemini_sata_driver);
 
+MODULE_DESCRIPTION("low level driver for Cortina Systems Gemini SATA bridge");
 MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:" DRV_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_highbank.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_highbank.c
@@ -348,6 +348,7 @@
 			phy_nodes[phy] = phy_data.np;
 			cphy_base[phy] = of_iomap(phy_nodes[phy], 0);
 			if (cphy_base[phy] == NULL) {
+				of_node_put(phy_data.np);
 				return 0;
 			}
 			phy_count += 1;
@@ -400,7 +401,7 @@
 
 	/* clear D2H reception area to properly wait for D2H FIS */
 	ata_tf_init(link->device, &tf);
-	tf.command = ATA_BUSY;
+	tf.status = ATA_BUSY;
 	ata_tf_to_fis(&tf, 0, 0, d2h_fis);
 
 	do {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_inic162x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_inic162x.c
@@ -559,13 +559,13 @@
 {
 	void __iomem *port_base = inic_port_base(ap);
 
-	tf->feature	= readb(port_base + PORT_TF_FEATURE);
+	tf->error	= readb(port_base + PORT_TF_FEATURE);
 	tf->nsect	= readb(port_base + PORT_TF_NSECT);
 	tf->lbal	= readb(port_base + PORT_TF_LBAL);
 	tf->lbam	= readb(port_base + PORT_TF_LBAM);
 	tf->lbah	= readb(port_base + PORT_TF_LBAH);
 	tf->device	= readb(port_base + PORT_TF_DEVICE);
-	tf->command	= readb(port_base + PORT_TF_COMMAND);
+	tf->status	= readb(port_base + PORT_TF_COMMAND);
 }
 
 static bool inic_qc_fill_rtf(struct ata_queued_cmd *qc)
@@ -582,11 +582,11 @@
 	 */
 	inic_tf_read(qc->ap, &tf);
 
-	if (!(tf.command & ATA_ERR))
+	if (!(tf.status & ATA_ERR))
 		return false;
 
-	rtf->command = tf.command;
-	rtf->feature = tf.feature;
+	rtf->status = tf.status;
+	rtf->error = tf.error;
 	return true;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_mv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_mv.c
@@ -787,37 +787,6 @@
 	},
 };
 
-static const struct pci_device_id mv_pci_tbl[] = {
-	{ PCI_VDEVICE(MARVELL, 0x5040), chip_504x },
-	{ PCI_VDEVICE(MARVELL, 0x5041), chip_504x },
-	{ PCI_VDEVICE(MARVELL, 0x5080), chip_5080 },
-	{ PCI_VDEVICE(MARVELL, 0x5081), chip_508x },
-	/* RocketRAID 1720/174x have different identifiers */
-	{ PCI_VDEVICE(TTI, 0x1720), chip_6042 },
-	{ PCI_VDEVICE(TTI, 0x1740), chip_6042 },
-	{ PCI_VDEVICE(TTI, 0x1742), chip_6042 },
-
-	{ PCI_VDEVICE(MARVELL, 0x6040), chip_604x },
-	{ PCI_VDEVICE(MARVELL, 0x6041), chip_604x },
-	{ PCI_VDEVICE(MARVELL, 0x6042), chip_6042 },
-	{ PCI_VDEVICE(MARVELL, 0x6080), chip_608x },
-	{ PCI_VDEVICE(MARVELL, 0x6081), chip_608x },
-
-	{ PCI_VDEVICE(ADAPTEC2, 0x0241), chip_604x },
-
-	/* Adaptec 1430SA */
-	{ PCI_VDEVICE(ADAPTEC2, 0x0243), chip_7042 },
-
-	/* Marvell 7042 support */
-	{ PCI_VDEVICE(MARVELL, 0x7042), chip_7042 },
-
-	/* Highpoint RocketRAID PCIe series */
-	{ PCI_VDEVICE(TTI, 0x2300), chip_7042 },
-	{ PCI_VDEVICE(TTI, 0x2310), chip_7042 },
-
-	{ }			/* terminate list */
-};
-
 static const struct mv_hw_ops mv5xxx_ops = {
 	.phy_errata		= mv5_phy_errata,
 	.enable_leds		= mv5_enable_leds,
@@ -4311,6 +4280,36 @@
 static int mv_pci_device_resume(struct pci_dev *pdev);
 #endif
 
+static const struct pci_device_id mv_pci_tbl[] = {
+	{ PCI_VDEVICE(MARVELL, 0x5040), chip_504x },
+	{ PCI_VDEVICE(MARVELL, 0x5041), chip_504x },
+	{ PCI_VDEVICE(MARVELL, 0x5080), chip_5080 },
+	{ PCI_VDEVICE(MARVELL, 0x5081), chip_508x },
+	/* RocketRAID 1720/174x have different identifiers */
+	{ PCI_VDEVICE(TTI, 0x1720), chip_6042 },
+	{ PCI_VDEVICE(TTI, 0x1740), chip_6042 },
+	{ PCI_VDEVICE(TTI, 0x1742), chip_6042 },
+
+	{ PCI_VDEVICE(MARVELL, 0x6040), chip_604x },
+	{ PCI_VDEVICE(MARVELL, 0x6041), chip_604x },
+	{ PCI_VDEVICE(MARVELL, 0x6042), chip_6042 },
+	{ PCI_VDEVICE(MARVELL, 0x6080), chip_608x },
+	{ PCI_VDEVICE(MARVELL, 0x6081), chip_608x },
+
+	{ PCI_VDEVICE(ADAPTEC2, 0x0241), chip_604x },
+
+	/* Adaptec 1430SA */
+	{ PCI_VDEVICE(ADAPTEC2, 0x0243), chip_7042 },
+
+	/* Marvell 7042 support */
+	{ PCI_VDEVICE(MARVELL, 0x7042), chip_7042 },
+
+	/* Highpoint RocketRAID PCIe series */
+	{ PCI_VDEVICE(TTI, 0x2300), chip_7042 },
+	{ PCI_VDEVICE(TTI, 0x2310), chip_7042 },
+
+	{ }			/* terminate list */
+};
 
 static struct pci_driver mv_pci_driver = {
 	.name			= DRV_NAME,
@@ -4323,6 +4322,7 @@
 #endif
 
 };
+MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
 
 /**
  *      mv_print_info - Dump key info to kernel log for perusal.
@@ -4495,7 +4495,6 @@
 MODULE_AUTHOR("Brett Russ");
 MODULE_DESCRIPTION("SCSI low-level driver for Marvell SATA controllers");
 MODULE_LICENSE("GPL v2");
-MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
 MODULE_VERSION(DRV_VERSION);
 MODULE_ALIAS("platform:" DRV_NAME);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_rcar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_rcar.c
@@ -417,8 +417,8 @@
 {
 	struct ata_ioports *ioaddr = &ap->ioaddr;
 
-	tf->command = sata_rcar_check_status(ap);
-	tf->feature = ioread32(ioaddr->error_addr);
+	tf->status = sata_rcar_check_status(ap);
+	tf->error = ioread32(ioaddr->error_addr);
 	tf->nsect = ioread32(ioaddr->nsect_addr);
 	tf->lbal = ioread32(ioaddr->lbal_addr);
 	tf->lbam = ioread32(ioaddr->lbam_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_sil.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_sil.c
@@ -128,7 +128,7 @@
 static const struct sil_drivelist {
 	const char *product;
 	unsigned int quirk;
-} sil_blacklist [] = {
+} sil_quirks[] = {
 	{ "ST320012AS",		SIL_QUIRK_MOD15WRITE },
 	{ "ST330013AS",		SIL_QUIRK_MOD15WRITE },
 	{ "ST340017AS",		SIL_QUIRK_MOD15WRITE },
@@ -601,8 +601,8 @@
  *	list, and apply the fixups to only the specific
  *	devices/hosts/firmwares that need it.
  *
- *	20040111 - Seagate drives affected by the Mod15Write bug are blacklisted
- *	The Maxtor quirk is in the blacklist, but I'm keeping the original
+ *	20040111 - Seagate drives affected by the Mod15Write bug are quirked
+ *	The Maxtor quirk is in sil_quirks, but I'm keeping the original
  *	pessimistic fix for the following reasons...
  *	- There seems to be less info on it, only one device gleaned off the
  *	Windows	driver, maybe only one is affected.  More info would be greatly
@@ -621,9 +621,9 @@
 
 	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
 
-	for (n = 0; sil_blacklist[n].product; n++)
-		if (!strcmp(sil_blacklist[n].product, model_num)) {
-			quirks = sil_blacklist[n].quirk;
+	for (n = 0; sil_quirks[n].product; n++)
+		if (!strcmp(sil_quirks[n].product, model_num)) {
+			quirks = sil_quirks[n].quirk;
 			break;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_svw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_svw.c
@@ -194,24 +194,24 @@
 static void k2_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
 {
 	struct ata_ioports *ioaddr = &ap->ioaddr;
-	u16 nsect, lbal, lbam, lbah, feature;
+	u16 nsect, lbal, lbam, lbah, error;
 
-	tf->command = k2_stat_check_status(ap);
+	tf->status = k2_stat_check_status(ap);
 	tf->device = readw(ioaddr->device_addr);
-	feature = readw(ioaddr->error_addr);
+	error = readw(ioaddr->error_addr);
 	nsect = readw(ioaddr->nsect_addr);
 	lbal = readw(ioaddr->lbal_addr);
 	lbam = readw(ioaddr->lbam_addr);
 	lbah = readw(ioaddr->lbah_addr);
 
-	tf->feature = feature;
+	tf->error = error;
 	tf->nsect = nsect;
 	tf->lbal = lbal;
 	tf->lbam = lbam;
 	tf->lbah = lbah;
 
 	if (tf->flags & ATA_TFLAG_LBA48) {
-		tf->hob_feature = feature >> 8;
+		tf->hob_feature = error >> 8;
 		tf->hob_nsect = nsect >> 8;
 		tf->hob_lbal = lbal >> 8;
 		tf->hob_lbam = lbam >> 8;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_sx4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_sx4.c
@@ -1004,8 +1004,7 @@
 
 	offset -= (idx * window_size);
 	idx++;
-	dist = ((long) (window_size - (offset + size))) >= 0 ? size :
-		(long) (window_size - offset);
+	dist = min(size, window_size - offset);
 	memcpy_fromio(psource, dimm_mmio + offset / 4, dist);
 
 	psource += dist;
@@ -1053,8 +1052,7 @@
 	readl(mmio + PDC_DIMM_WINDOW_CTLR);
 	offset -= (idx * window_size);
 	idx++;
-	dist = ((long)(s32)(window_size - (offset + size))) >= 0 ? size :
-		(long) (window_size - offset);
+	dist = min(size, window_size - offset);
 	memcpy_toio(dimm_mmio + offset / 4, psource, dist);
 	writel(0x01, mmio + PDC_GENERAL_CTLR);
 	readl(mmio + PDC_GENERAL_CTLR);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ata/sata_vsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ata/sata_vsc.c
@@ -183,24 +183,24 @@
 static void vsc_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
 {
 	struct ata_ioports *ioaddr = &ap->ioaddr;
-	u16 nsect, lbal, lbam, lbah, feature;
+	u16 nsect, lbal, lbam, lbah, error;
 
-	tf->command = ata_sff_check_status(ap);
+	tf->status = ata_sff_check_status(ap);
 	tf->device = readw(ioaddr->device_addr);
-	feature = readw(ioaddr->error_addr);
+	error = readw(ioaddr->error_addr);
 	nsect = readw(ioaddr->nsect_addr);
 	lbal = readw(ioaddr->lbal_addr);
 	lbam = readw(ioaddr->lbam_addr);
 	lbah = readw(ioaddr->lbah_addr);
 
-	tf->feature = feature;
+	tf->error = error;
 	tf->nsect = nsect;
 	tf->lbal = lbal;
 	tf->lbam = lbam;
 	tf->lbah = lbah;
 
 	if (tf->flags & ATA_TFLAG_LBA48) {
-		tf->hob_feature = feature >> 8;
+		tf->hob_feature = error >> 8;
 		tf->hob_nsect = nsect >> 8;
 		tf->hob_lbal = lbal >> 8;
 		tf->hob_lbam = lbam >> 8;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/atm/eni.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/atm/eni.c
@@ -1112,6 +1112,8 @@
 	skb_data3 = skb->data[3];
 	paddr = dma_map_single(&eni_dev->pci_dev->dev,skb->data,skb->len,
 			       DMA_TO_DEVICE);
+	if (dma_mapping_error(&eni_dev->pci_dev->dev, paddr))
+		return enq_next;
 	ENI_PRV_PADDR(skb) = paddr;
 	/* prepare DMA queue entries */
 	j = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/atm/firestream.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/atm/firestream.c
@@ -1676,6 +1676,8 @@
 	dev->hw_base = pci_resource_start(pci_dev, 0);
 
 	dev->base = ioremap(dev->hw_base, 0x1000);
+	if (!dev->base)
+		return 1;
 
 	reset_chip (dev);
   
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/atm/idt77252.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/atm/idt77252.c
@@ -1118,8 +1118,8 @@
 	rpp->len += skb->len;
 
 	if (stat & SAR_RSQE_EPDU) {
+		unsigned int len, truesize;
 		unsigned char *l1l2;
-		unsigned int len;
 
 		l1l2 = (unsigned char *) ((unsigned long) skb->data + skb->len - 6);
 
@@ -1189,14 +1189,15 @@
 		ATM_SKB(skb)->vcc = vcc;
 		__net_timestamp(skb);
 
+		truesize = skb->truesize;
 		vcc->push(vcc, skb);
 		atomic_inc(&vcc->stats->rx);
 
-		if (skb->truesize > SAR_FB_SIZE_3)
+		if (truesize > SAR_FB_SIZE_3)
 			add_rx_skb(card, 3, SAR_FB_SIZE_3, 1);
-		else if (skb->truesize > SAR_FB_SIZE_2)
+		else if (truesize > SAR_FB_SIZE_2)
 			add_rx_skb(card, 2, SAR_FB_SIZE_2, 1);
-		else if (skb->truesize > SAR_FB_SIZE_1)
+		else if (truesize > SAR_FB_SIZE_1)
 			add_rx_skb(card, 1, SAR_FB_SIZE_1, 1);
 		else
 			add_rx_skb(card, 0, SAR_FB_SIZE_0, 1);
@@ -2909,6 +2910,7 @@
 
 				recycle_rx_pool_skb(card, &vc->rcv.rx_pool);
 			}
+			kfree(vc);
 		}
 	}
 }
@@ -2929,6 +2931,8 @@
 	vc->scq = alloc_scq(card, vc->class);
 	if (!vc->scq) {
 		printk("%s: can't get SCQ.\n", card->name);
+		kfree(card->vcs[0]);
+		card->vcs[0] = NULL;
 		return -ENOMEM;
 	}
 
@@ -2952,6 +2956,15 @@
 	return 0;
 }
 
+static void
+close_card_ubr0(struct idt77252_dev *card)
+{
+	struct vc_map *vc = card->vcs[0];
+
+	free_scq(card, vc->scq);
+	kfree(vc);
+}
+
 static int
 idt77252_dev_open(struct idt77252_dev *card)
 {
@@ -3001,6 +3014,7 @@
 	struct idt77252_dev *card = dev->dev_data;
 	u32 conf;
 
+	close_card_ubr0(card);
 	close_card_oam(card);
 
 	conf = SAR_CFG_RXPTH |	/* enable receive path           */
@@ -3752,6 +3766,7 @@
 		card = idt77252_chain;
 		dev = card->atmdev;
 		idt77252_chain = card->next;
+		del_timer_sync(&card->tst_timer);
 
 		if (dev->phy->stop)
 			dev->phy->stop(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/atm/iphase.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/atm/iphase.c
@@ -2293,19 +2293,21 @@
 static int reset_sar(struct atm_dev *dev)  
 {  
 	IADEV *iadev;  
-	int i, error = 1;  
+	int i, error;
 	unsigned int pci[64];  
 	  
 	iadev = INPH_IA_DEV(dev);  
-	for(i=0; i<64; i++)  
-	  if ((error = pci_read_config_dword(iadev->pci,  
-				i*4, &pci[i])) != PCIBIOS_SUCCESSFUL)  
-  	      return error;  
+	for (i = 0; i < 64; i++) {
+		error = pci_read_config_dword(iadev->pci, i * 4, &pci[i]);
+		if (error != PCIBIOS_SUCCESSFUL)
+			return error;
+	}
 	writel(0, iadev->reg+IPHASE5575_EXT_RESET);  
-	for(i=0; i<64; i++)  
-	  if ((error = pci_write_config_dword(iadev->pci,  
-					i*4, pci[i])) != PCIBIOS_SUCCESSFUL)  
-	    return error;  
+	for (i = 0; i < 64; i++) {
+		error = pci_write_config_dword(iadev->pci, i * 4, pci[i]);
+		if (error != PCIBIOS_SUCCESSFUL)
+			return error;
+	}
 	udelay(5);  
 	return 0;  
 }  
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/atm/solos-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/atm/solos-pci.c
@@ -449,9 +449,9 @@
 	struct sk_buff *skb;
 	unsigned int len;
 
-	spin_lock(&card->cli_queue_lock);
+	spin_lock_bh(&card->cli_queue_lock);
 	skb = skb_dequeue(&card->cli_queue[SOLOS_CHAN(atmdev)]);
-	spin_unlock(&card->cli_queue_lock);
+	spin_unlock_bh(&card->cli_queue_lock);
 	if(skb == NULL)
 		return sprintf(buf, "No data.\n");
 
@@ -956,14 +956,14 @@
 	struct pkt_hdr *header;
 
 	/* Remove any yet-to-be-transmitted packets from the pending queue */
-	spin_lock(&card->tx_queue_lock);
+	spin_lock_bh(&card->tx_queue_lock);
 	skb_queue_walk_safe(&card->tx_queue[port], skb, tmpskb) {
 		if (SKB_CB(skb)->vcc == vcc) {
 			skb_unlink(skb, &card->tx_queue[port]);
 			solos_pop(vcc, skb);
 		}
 	}
-	spin_unlock(&card->tx_queue_lock);
+	spin_unlock_bh(&card->tx_queue_lock);
 
 	skb = alloc_skb(sizeof(*header), GFP_KERNEL);
 	if (!skb) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/auxdisplay/charlcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/auxdisplay/charlcd.c
@@ -578,6 +578,9 @@
 	 * Since charlcd_init_display() needs to write data, we have to
 	 * enable mark the LCD initialized just before.
 	 */
+	if (WARN_ON(!lcd->ops->init_display))
+		return -EINVAL;
+
 	ret = lcd->ops->init_display(lcd);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/auxdisplay/hd44780.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/auxdisplay/hd44780.c
@@ -322,8 +322,10 @@
 static int hd44780_remove(struct platform_device *pdev)
 {
 	struct charlcd *lcd = platform_get_drvdata(pdev);
+	struct hd44780_common *hdc = lcd->drvdata;
 
 	charlcd_unregister(lcd);
+	kfree(hdc->hd44780);
 	kfree(lcd->drvdata);
 
 	kfree(lcd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/auxdisplay/ht16k33.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/auxdisplay/ht16k33.c
@@ -219,6 +219,15 @@
 	.check_fb	= ht16k33_bl_check_fb,
 };
 
+/*
+ * Blank events will be passed to the actual device handling the backlight when
+ * we return zero here.
+ */
+static int ht16k33_blank(int blank, struct fb_info *info)
+{
+	return 0;
+}
+
 static int ht16k33_mmap(struct fb_info *info, struct vm_area_struct *vma)
 {
 	struct ht16k33_priv *priv = info->par;
@@ -231,6 +240,7 @@
 	.owner = THIS_MODULE,
 	.fb_read = fb_sys_read,
 	.fb_write = fb_sys_write,
+	.fb_blank = ht16k33_blank,
 	.fb_fillrect = sys_fillrect,
 	.fb_copyarea = sys_copyarea,
 	.fb_imageblit = sys_imageblit,
@@ -413,6 +423,33 @@
 	if (err)
 		return err;
 
+	/* Backlight */
+	memset(&bl_props, 0, sizeof(struct backlight_properties));
+	bl_props.type = BACKLIGHT_RAW;
+	bl_props.max_brightness = MAX_BRIGHTNESS;
+
+	bl = devm_backlight_device_register(&client->dev, DRIVER_NAME"-bl",
+					    &client->dev, priv,
+					    &ht16k33_bl_ops, &bl_props);
+	if (IS_ERR(bl)) {
+		dev_err(&client->dev, "failed to register backlight\n");
+		return PTR_ERR(bl);
+	}
+
+	err = of_property_read_u32(node, "default-brightness-level",
+				   &dft_brightness);
+	if (err) {
+		dft_brightness = MAX_BRIGHTNESS;
+	} else if (dft_brightness > MAX_BRIGHTNESS) {
+		dev_warn(&client->dev,
+			 "invalid default brightness level: %u, using %u\n",
+			 dft_brightness, MAX_BRIGHTNESS);
+		dft_brightness = MAX_BRIGHTNESS;
+	}
+
+	bl->props.brightness = dft_brightness;
+	ht16k33_bl_update_status(bl);
+
 	/* Framebuffer (2 bytes per column) */
 	BUILD_BUG_ON(PAGE_SIZE < HT16K33_FB_SIZE);
 	fbdev->buffer = (unsigned char *) get_zeroed_page(GFP_KERNEL);
@@ -445,6 +482,7 @@
 	fbdev->info->screen_size = HT16K33_FB_SIZE;
 	fbdev->info->fix = ht16k33_fb_fix;
 	fbdev->info->var = ht16k33_fb_var;
+	fbdev->info->bl_dev = bl;
 	fbdev->info->pseudo_palette = NULL;
 	fbdev->info->flags = FBINFO_FLAG_DEFAULT;
 	fbdev->info->par = priv;
@@ -460,34 +498,6 @@
 			goto err_fbdev_unregister;
 	}
 
-	/* Backlight */
-	memset(&bl_props, 0, sizeof(struct backlight_properties));
-	bl_props.type = BACKLIGHT_RAW;
-	bl_props.max_brightness = MAX_BRIGHTNESS;
-
-	bl = devm_backlight_device_register(&client->dev, DRIVER_NAME"-bl",
-					    &client->dev, priv,
-					    &ht16k33_bl_ops, &bl_props);
-	if (IS_ERR(bl)) {
-		dev_err(&client->dev, "failed to register backlight\n");
-		err = PTR_ERR(bl);
-		goto err_fbdev_unregister;
-	}
-
-	err = of_property_read_u32(node, "default-brightness-level",
-				   &dft_brightness);
-	if (err) {
-		dft_brightness = MAX_BRIGHTNESS;
-	} else if (dft_brightness > MAX_BRIGHTNESS) {
-		dev_warn(&client->dev,
-			 "invalid default brightness level: %u, using %u\n",
-			 dft_brightness, MAX_BRIGHTNESS);
-		dft_brightness = MAX_BRIGHTNESS;
-	}
-
-	bl->props.brightness = dft_brightness;
-	ht16k33_bl_update_status(bl);
-
 	ht16k33_fb_queue(priv);
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/auxdisplay/img-ascii-lcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/auxdisplay/img-ascii-lcd.c
@@ -280,6 +280,16 @@
 	if (msg[count - 1] == '\n')
 		count--;
 
+	if (!count) {
+		/* clear the LCD */
+		devm_kfree(&ctx->pdev->dev, ctx->message);
+		ctx->message = NULL;
+		ctx->message_len = 0;
+		memset(ctx->curr, ' ', ctx->cfg->num_chars);
+		ctx->cfg->update(ctx);
+		return 0;
+	}
+
 	new_msg = devm_kmalloc(&ctx->pdev->dev, count + 1, GFP_KERNEL);
 	if (!new_msg)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/auxdisplay/lcd2s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/auxdisplay/lcd2s.c
@@ -238,7 +238,7 @@
 	if (buf[1] > 7)
 		return 1;
 
-	i = 0;
+	i = 2;
 	shift = 0;
 	value = 0;
 	while (*esc && i < LCD2S_CHARACTER_SIZE + 2) {
@@ -298,6 +298,10 @@
 			I2C_FUNC_SMBUS_WRITE_BLOCK_DATA))
 		return -EIO;
 
+	lcd2s = devm_kzalloc(&i2c->dev, sizeof(*lcd2s), GFP_KERNEL);
+	if (!lcd2s)
+		return -ENOMEM;
+
 	/* Test, if the display is responding */
 	err = lcd2s_i2c_smbus_write_byte(i2c, LCD2S_CMD_DISPLAY_OFF);
 	if (err < 0)
@@ -307,12 +311,6 @@
 	if (!lcd)
 		return -ENOMEM;
 
-	lcd2s = kzalloc(sizeof(struct lcd2s_data), GFP_KERNEL);
-	if (!lcd2s) {
-		err = -ENOMEM;
-		goto fail1;
-	}
-
 	lcd->drvdata = lcd2s;
 	lcd2s->i2c = i2c;
 	lcd2s->charlcd = lcd;
@@ -321,26 +319,24 @@
 	err = device_property_read_u32(&i2c->dev, "display-height-chars",
 			&lcd->height);
 	if (err)
-		goto fail2;
+		goto fail1;
 
 	err = device_property_read_u32(&i2c->dev, "display-width-chars",
 			&lcd->width);
 	if (err)
-		goto fail2;
+		goto fail1;
 
 	lcd->ops = &lcd2s_ops;
 
 	err = charlcd_register(lcd2s->charlcd);
 	if (err)
-		goto fail2;
+		goto fail1;
 
 	i2c_set_clientdata(i2c, lcd2s);
 	return 0;
 
-fail2:
-	kfree(lcd2s);
 fail1:
-	kfree(lcd);
+	charlcd_free(lcd2s->charlcd);
 	return err;
 }
 
@@ -349,7 +345,7 @@
 	struct lcd2s_data *lcd2s = i2c_get_clientdata(i2c);
 
 	charlcd_unregister(lcd2s->charlcd);
-	kfree(lcd2s->charlcd);
+	charlcd_free(lcd2s->charlcd);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/arch_numa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/arch_numa.c
@@ -144,7 +144,7 @@
 unsigned long __per_cpu_offset[NR_CPUS] __read_mostly;
 EXPORT_SYMBOL(__per_cpu_offset);
 
-static int __init early_cpu_to_node(int cpu)
+int __init early_cpu_to_node(int cpu)
 {
 	return cpu_to_node_map[cpu];
 }
@@ -165,7 +165,7 @@
 
 static void __init pcpu_fc_free(void *ptr, size_t size)
 {
-	memblock_free_early(__pa(ptr), size);
+	memblock_free(__pa(ptr), size);
 }
 
 void __init setup_per_cpu_areas(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/arch_topology.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/arch_topology.c
@@ -609,7 +609,7 @@
 	for_each_online_cpu(cpu) {
 		cpu_topo = &cpu_topology[cpu];
 
-		if (cpuid_topo->llc_id == cpu_topo->llc_id) {
+		if (cpu_topo->llc_id != -1 && cpuid_topo->llc_id == cpu_topo->llc_id) {
 			cpumask_set_cpu(cpu, &cpuid_topo->llc_sibling);
 			cpumask_set_cpu(cpuid, &cpu_topo->llc_sibling);
 		}
@@ -690,4 +690,23 @@
 	else if (of_have_populated_dt() && parse_dt_topology())
 		reset_cpu_topology();
 }
+
+void store_cpu_topology(unsigned int cpuid)
+{
+	struct cpu_topology *cpuid_topo = &cpu_topology[cpuid];
+
+	if (cpuid_topo->package_id != -1)
+		goto topology_populated;
+
+	cpuid_topo->thread_id = -1;
+	cpuid_topo->core_id = cpuid;
+	cpuid_topo->package_id = cpu_to_node(cpuid);
+
+	pr_debug("CPU%u: package %d core %d thread %d\n",
+		 cpuid, cpuid_topo->package_id, cpuid_topo->core_id,
+		 cpuid_topo->thread_id);
+
+topology_populated:
+	update_siblings_masks(cpuid);
+}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/bus.c
@@ -104,7 +104,8 @@
 {
 	struct bus_attribute *bus_attr = to_bus_attr(attr);
 	struct subsys_private *subsys_priv = to_subsys_private(kobj);
-	ssize_t ret = 0;
+	/* return -EIO for reading a bus attribute without show() */
+	ssize_t ret = -EIO;
 
 	if (bus_attr->show)
 		ret = bus_attr->show(subsys_priv->bus, buf);
@@ -116,7 +117,8 @@
 {
 	struct bus_attribute *bus_attr = to_bus_attr(attr);
 	struct subsys_private *subsys_priv = to_subsys_private(kobj);
-	ssize_t ret = 0;
+	/* return -EIO for writing a bus attribute without store() */
+	ssize_t ret = -EIO;
 
 	if (bus_attr->store)
 		ret = bus_attr->store(subsys_priv->bus, buf, count);
@@ -617,7 +619,7 @@
 	if (drv->bus->p->drivers_autoprobe) {
 		error = driver_attach(drv);
 		if (error)
-			goto out_unregister;
+			goto out_del_list;
 	}
 	module_add_driver(drv->owner, drv);
 
@@ -644,6 +646,8 @@
 
 	return 0;
 
+out_del_list:
+	klist_del(&priv->knode_bus);
 out_unregister:
 	kobject_put(&priv->kobj);
 	/* drv->p is freed in driver_release()  */
@@ -849,6 +853,8 @@
 	bus_remove_file(bus, &bus_attr_uevent);
 bus_uevent_fail:
 	kset_unregister(&bus->p->subsys);
+	/* Above kset_unregister() will kfree @bus->p */
+	bus->p = NULL;
 out:
 	kfree(bus->p);
 	bus->p = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/class.c
@@ -192,6 +192,11 @@
 	}
 	error = class_add_groups(class_get(cls), cls->class_groups);
 	class_put(cls);
+	if (error) {
+		kobject_del(&cp->subsys.kobj);
+		kfree_const(cp->subsys.kobj.name);
+		kfree(cp);
+	}
 	return error;
 }
 EXPORT_SYMBOL_GPL(__class_register);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/component.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/component.c
@@ -130,7 +130,7 @@
 
 static void component_master_debugfs_del(struct master *m)
 {
-	debugfs_remove(debugfs_lookup(dev_name(m->parent), component_debugfs_dir));
+	debugfs_lookup_and_remove(dev_name(m->parent), component_debugfs_dir);
 }
 
 #else
@@ -246,7 +246,7 @@
 		return 0;
 	}
 
-	if (!devres_open_group(master->parent, NULL, GFP_KERNEL))
+	if (!devres_open_group(master->parent, master, GFP_KERNEL))
 		return -ENOMEM;
 
 	/* Found all components */
@@ -258,6 +258,7 @@
 		return ret;
 	}
 
+	devres_close_group(master->parent, NULL);
 	master->bound = true;
 	return 1;
 }
@@ -282,7 +283,7 @@
 {
 	if (master->bound) {
 		master->ops->unbind(master->parent);
-		devres_release_group(master->parent, NULL);
+		devres_release_group(master->parent, master);
 		master->bound = false;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/core.c
@@ -53,6 +53,7 @@
 static DEFINE_MUTEX(fwnode_link_lock);
 static bool fw_devlink_is_permissive(void);
 static bool fw_devlink_drv_reg_done;
+static struct workqueue_struct *device_link_wq;
 
 /**
  * fwnode_link_add - Create a link between two fwnode_handles.
@@ -485,8 +486,8 @@
 	/* Ensure that all references to the link object have been dropped. */
 	device_link_synchronize_removal();
 
-	while (refcount_dec_not_one(&link->rpm_active))
-		pm_runtime_put(link->supplier);
+	pm_runtime_release_supplier(link);
+	pm_request_idle(link->supplier);
 
 	put_device(link->consumer);
 	put_device(link->supplier);
@@ -501,12 +502,26 @@
 	/*
 	 * It may take a while to complete this work because of the SRCU
 	 * synchronization in device_link_release_fn() and if the consumer or
-	 * supplier devices get deleted when it runs, so put it into the "long"
-	 * workqueue.
+	 * supplier devices get deleted when it runs, so put it into the
+	 * dedicated workqueue.
 	 */
-	queue_work(system_long_wq, &link->rm_work);
+	queue_work(device_link_wq, &link->rm_work);
 }
 
+/**
+ * device_link_wait_removal - Wait for ongoing devlink removal jobs to terminate
+ */
+void device_link_wait_removal(void)
+{
+	/*
+	 * devlink removal jobs are queued in the dedicated work queue.
+	 * To be sure that all removal jobs are terminated, ensure that any
+	 * scheduled work has run to completion.
+	 */
+	flush_workqueue(device_link_wq);
+}
+EXPORT_SYMBOL_GPL(device_link_wait_removal);
+
 static struct class devlink_class = {
 	.name = "devlink",
 	.owner = THIS_MODULE,
@@ -821,9 +836,7 @@
 		     dev_bus_name(supplier), dev_name(supplier),
 		     dev_bus_name(consumer), dev_name(consumer));
 	if (device_register(&link->link_dev)) {
-		put_device(consumer);
-		put_device(supplier);
-		kfree(link);
+		put_device(&link->link_dev);
 		link = NULL;
 		goto out;
 	}
@@ -2391,8 +2404,11 @@
 	if (!env)
 		return -ENOMEM;
 
+	/* Synchronize with really_probe() */
+	device_lock(dev);
 	/* let the kset specific function add its keys */
 	retval = kset->uevent_ops->uevent(kset, &dev->kobj, env);
+	device_unlock(dev);
 	if (retval)
 		goto out;
 
@@ -3330,7 +3346,7 @@
 	/* we require the name to be set before, and pass NULL */
 	error = kobject_add(&dev->kobj, dev->kobj.parent, NULL);
 	if (error) {
-		glue_dir = get_glue_dir(dev);
+		glue_dir = kobj;
 		goto Error;
 	}
 
@@ -3430,6 +3446,7 @@
 	device_pm_remove(dev);
 	dpm_sysfs_remove(dev);
  DPMError:
+	dev->driver = NULL;
 	bus_remove_device(dev);
  BusError:
 	device_remove_attrs(dev);
@@ -3812,6 +3829,26 @@
 }
 EXPORT_SYMBOL_GPL(device_find_child_by_name);
 
+static int match_any(struct device *dev, void *unused)
+{
+	return 1;
+}
+
+/**
+ * device_find_any_child - device iterator for locating a child device, if any.
+ * @parent: parent struct device
+ *
+ * This is similar to the device_find_child() function above, but it
+ * returns a reference to a child device, if any.
+ *
+ * NOTE: you will need to drop the reference with put_device() after use.
+ */
+struct device *device_find_any_child(struct device *parent)
+{
+	return device_find_child(parent, NULL, match_any);
+}
+EXPORT_SYMBOL_GPL(device_find_any_child);
+
 int __init devices_init(void)
 {
 	devices_kset = kset_create_and_add("devices", &device_uevent_ops, NULL);
@@ -3826,9 +3863,14 @@
 	sysfs_dev_char_kobj = kobject_create_and_add("char", dev_kobj);
 	if (!sysfs_dev_char_kobj)
 		goto char_kobj_err;
+	device_link_wq = alloc_workqueue("device_link_wq", 0, 0);
+	if (!device_link_wq)
+		goto wq_err;
 
 	return 0;
 
+ wq_err:
+	kobject_put(sysfs_dev_char_kobj);
  char_kobj_err:
 	kobject_put(sysfs_dev_block_kobj);
  block_kobj_err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/cpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/cpu.c
@@ -487,7 +487,8 @@
 bool cpu_is_hotpluggable(unsigned int cpu)
 {
 	struct device *dev = get_cpu_device(cpu);
-	return dev && container_of(dev, struct cpu, dev)->hotpluggable;
+	return dev && container_of(dev, struct cpu, dev)->hotpluggable
+		&& tick_nohz_cpu_hotpluggable(cpu);
 }
 EXPORT_SYMBOL_GPL(cpu_is_hotpluggable);
 
@@ -564,6 +565,36 @@
 	return sysfs_emit(buf, "Not affected\n");
 }
 
+ssize_t __weak cpu_show_mmio_stale_data(struct device *dev,
+					struct device_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "Not affected\n");
+}
+
+ssize_t __weak cpu_show_retbleed(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "Not affected\n");
+}
+
+ssize_t __weak cpu_show_gds(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "Not affected\n");
+}
+
+ssize_t __weak cpu_show_spec_rstack_overflow(struct device *dev,
+					     struct device_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "Not affected\n");
+}
+
+ssize_t __weak cpu_show_reg_file_data_sampling(struct device *dev,
+					       struct device_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "Not affected\n");
+}
+
 static DEVICE_ATTR(meltdown, 0444, cpu_show_meltdown, NULL);
 static DEVICE_ATTR(spectre_v1, 0444, cpu_show_spectre_v1, NULL);
 static DEVICE_ATTR(spectre_v2, 0444, cpu_show_spectre_v2, NULL);
@@ -573,6 +604,11 @@
 static DEVICE_ATTR(tsx_async_abort, 0444, cpu_show_tsx_async_abort, NULL);
 static DEVICE_ATTR(itlb_multihit, 0444, cpu_show_itlb_multihit, NULL);
 static DEVICE_ATTR(srbds, 0444, cpu_show_srbds, NULL);
+static DEVICE_ATTR(mmio_stale_data, 0444, cpu_show_mmio_stale_data, NULL);
+static DEVICE_ATTR(retbleed, 0444, cpu_show_retbleed, NULL);
+static DEVICE_ATTR(gather_data_sampling, 0444, cpu_show_gds, NULL);
+static DEVICE_ATTR(spec_rstack_overflow, 0444, cpu_show_spec_rstack_overflow, NULL);
+static DEVICE_ATTR(reg_file_data_sampling, 0444, cpu_show_reg_file_data_sampling, NULL);
 
 static struct attribute *cpu_root_vulnerabilities_attrs[] = {
 	&dev_attr_meltdown.attr,
@@ -584,6 +620,11 @@
 	&dev_attr_tsx_async_abort.attr,
 	&dev_attr_itlb_multihit.attr,
 	&dev_attr_srbds.attr,
+	&dev_attr_mmio_stale_data.attr,
+	&dev_attr_retbleed.attr,
+	&dev_attr_gather_data_sampling.attr,
+	&dev_attr_spec_rstack_overflow.attr,
+	&dev_attr_reg_file_data_sampling.attr,
 	NULL
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/dd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/dd.c
@@ -257,7 +257,6 @@
 
 int driver_deferred_probe_timeout;
 EXPORT_SYMBOL_GPL(driver_deferred_probe_timeout);
-static DECLARE_WAIT_QUEUE_HEAD(probe_timeout_waitqueue);
 
 static int __init deferred_probe_timeout_setup(char *str)
 {
@@ -296,6 +295,7 @@
 
 	return -EPROBE_DEFER;
 }
+EXPORT_SYMBOL_GPL(driver_deferred_probe_check_state);
 
 static void deferred_probe_timeout_work_func(struct work_struct *work)
 {
@@ -311,7 +311,6 @@
 	list_for_each_entry(p, &deferred_probe_pending_list, deferred_probe)
 		dev_info(p->device, "deferred probe pending\n");
 	mutex_unlock(&deferred_probe_mutex);
-	wake_up_all(&probe_timeout_waitqueue);
 }
 static DECLARE_DELAYED_WORK(deferred_probe_timeout_work, deferred_probe_timeout_work_func);
 
@@ -353,7 +352,7 @@
 
 static void __exit deferred_probe_exit(void)
 {
-	debugfs_remove_recursive(debugfs_lookup("devices_deferred", NULL));
+	debugfs_lookup_and_remove("devices_deferred", NULL);
 }
 __exitcall(deferred_probe_exit);
 
@@ -629,6 +628,9 @@
 			drv->remove(dev);
 
 		devres_release_all(dev);
+		arch_teardown_dma_ops(dev);
+		kfree(dev->dma_range_map);
+		dev->dma_range_map = NULL;
 		driver_sysfs_remove(dev);
 		dev->driver = NULL;
 		dev_set_drvdata(dev, NULL);
@@ -688,7 +690,12 @@
 	calltime = ktime_get();
 	ret = really_probe(dev, drv);
 	rettime = ktime_get();
-	pr_debug("probe of %s returned %d after %lld usecs\n",
+	/*
+	 * Don't change this to pr_debug() because that requires
+	 * CONFIG_DYNAMIC_DEBUG and we want a simple 'initcall_debug' on the
+	 * kernel commandline to print this all the time at the debug level.
+	 */
+	printk(KERN_DEBUG "probe of %s returned %d after %lld usecs\n",
 		 dev_name(dev), ret, ktime_us_delta(rettime, calltime));
 	return ret;
 }
@@ -715,9 +722,6 @@
  */
 void wait_for_device_probe(void)
 {
-	/* wait for probe timeout */
-	wait_event(probe_timeout_waitqueue, !driver_deferred_probe_timeout);
-
 	/* wait for the deferred probe workqueue to finish */
 	flush_work(&deferred_probe_work);
 
@@ -806,7 +810,7 @@
 		pr_warn("Too long list of driver names for 'driver_async_probe'!\n");
 
 	strlcpy(async_probe_drv_names, buf, ASYNC_DRV_NAMES_MAX_LEN);
-	return 0;
+	return 1;
 }
 __setup("driver_async_probe=", save_async_options);
 
@@ -878,6 +882,11 @@
 		dev_dbg(dev, "Device match requests probe deferral\n");
 		dev->can_match = true;
 		driver_deferred_probe_add(dev);
+		/*
+		 * Device can't match with a driver right now, so don't attempt
+		 * to match or bind with other drivers on the bus.
+		 */
+		return ret;
 	} else if (ret < 0) {
 		dev_dbg(dev, "Bus failed to match device: %d\n", ret);
 		return ret;
@@ -940,6 +949,7 @@
 static int __device_attach(struct device *dev, bool allow_async)
 {
 	int ret = 0;
+	bool async = false;
 
 	device_lock(dev);
 	if (dev->p->dead) {
@@ -978,7 +988,7 @@
 			 */
 			dev_dbg(dev, "scheduling asynchronous probe\n");
 			get_device(dev);
-			async_schedule_dev(__device_attach_async_helper, dev);
+			async = true;
 		} else {
 			pm_request_idle(dev);
 		}
@@ -988,6 +998,8 @@
 	}
 out_unlock:
 	device_unlock(dev);
+	if (async)
+		async_schedule_dev(__device_attach_async_helper, dev);
 	return ret;
 }
 
@@ -1092,6 +1104,7 @@
 static int __driver_attach(struct device *dev, void *data)
 {
 	struct device_driver *drv = data;
+	bool async = false;
 	int ret;
 
 	/*
@@ -1112,9 +1125,18 @@
 		dev_dbg(dev, "Device match requests probe deferral\n");
 		dev->can_match = true;
 		driver_deferred_probe_add(dev);
+		/*
+		 * Driver could not match with device, but may match with
+		 * another device on the bus.
+		 */
+		return 0;
 	} else if (ret < 0) {
 		dev_dbg(dev, "Bus failed to match device: %d\n", ret);
-		return ret;
+		/*
+		 * Driver could not match with device, but may match with
+		 * another device on the bus.
+		 */
+		return 0;
 	} /* ret > 0 means positive match */
 
 	if (driver_allows_async_probing(drv)) {
@@ -1130,9 +1152,11 @@
 		if (!dev->driver) {
 			get_device(dev);
 			dev->p->async_driver = drv;
-			async_schedule_dev(__driver_attach_async_helper, dev);
+			async = true;
 		}
 		device_unlock(dev);
+		if (async)
+			async_schedule_dev(__driver_attach_async_helper, dev);
 		return 0;
 	}
 
@@ -1204,10 +1228,10 @@
 		else if (drv->remove)
 			drv->remove(dev);
 
-		device_links_driver_cleanup(dev);
-
 		devres_release_all(dev);
 		arch_teardown_dma_ops(dev);
+		kfree(dev->dma_range_map);
+		dev->dma_range_map = NULL;
 		dev->driver = NULL;
 		dev_set_drvdata(dev, NULL);
 		if (dev->pm_domain && dev->pm_domain->dismiss)
@@ -1215,6 +1239,8 @@
 		pm_runtime_reinit(dev);
 		dev_pm_set_driver_flags(dev, 0);
 
+		device_links_driver_cleanup(dev);
+
 		klist_remove(&dev->p->knode_driver);
 		device_pm_check_callbacks(dev);
 		if (dev->bus)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/devcoredump.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/devcoredump.c
@@ -25,6 +25,47 @@
 	struct device devcd_dev;
 	void *data;
 	size_t datalen;
+	/*
+	 * Here, mutex is required to serialize the calls to del_wk work between
+	 * user/kernel space which happens when devcd is added with device_add()
+	 * and that sends uevent to user space. User space reads the uevents,
+	 * and calls to devcd_data_write() which try to modify the work which is
+	 * not even initialized/queued from devcoredump.
+	 *
+	 *
+	 *
+	 *        cpu0(X)                                 cpu1(Y)
+	 *
+	 *        dev_coredump() uevent sent to user space
+	 *        device_add()  ======================> user space process Y reads the
+	 *                                              uevents writes to devcd fd
+	 *                                              which results into writes to
+	 *
+	 *                                             devcd_data_write()
+	 *                                               mod_delayed_work()
+	 *                                                 try_to_grab_pending()
+	 *                                                   del_timer()
+	 *                                                     debug_assert_init()
+	 *       INIT_DELAYED_WORK()
+	 *       schedule_delayed_work()
+	 *
+	 *
+	 * Also, mutex alone would not be enough to avoid scheduling of
+	 * del_wk work after it get flush from a call to devcd_free()
+	 * mentioned as below.
+	 *
+	 *	disabled_store()
+	 *        devcd_free()
+	 *          mutex_lock()             devcd_data_write()
+	 *          flush_delayed_work()
+	 *          mutex_unlock()
+	 *                                   mutex_lock()
+	 *                                   mod_delayed_work()
+	 *                                   mutex_unlock()
+	 * So, delete_work flag is required.
+	 */
+	struct mutex mutex;
+	bool delete_work;
 	struct module *owner;
 	ssize_t (*read)(char *buffer, loff_t offset, size_t count,
 			void *data, size_t datalen);
@@ -84,7 +125,12 @@
 	struct device *dev = kobj_to_dev(kobj);
 	struct devcd_entry *devcd = dev_to_devcd(dev);
 
-	mod_delayed_work(system_wq, &devcd->del_wk, 0);
+	mutex_lock(&devcd->mutex);
+	if (!devcd->delete_work) {
+		devcd->delete_work = true;
+		mod_delayed_work(system_wq, &devcd->del_wk, 0);
+	}
+	mutex_unlock(&devcd->mutex);
 
 	return count;
 }
@@ -112,7 +158,12 @@
 {
 	struct devcd_entry *devcd = dev_to_devcd(dev);
 
+	mutex_lock(&devcd->mutex);
+	if (!devcd->delete_work)
+		devcd->delete_work = true;
+
 	flush_delayed_work(&devcd->del_wk);
+	mutex_unlock(&devcd->mutex);
 	return 0;
 }
 
@@ -122,6 +173,30 @@
 	return sysfs_emit(buf, "%d\n", devcd_disabled);
 }
 
+/*
+ *
+ *	disabled_store()                                	worker()
+ *	 class_for_each_device(&devcd_class,
+ *		NULL, NULL, devcd_free)
+ *         ...
+ *         ...
+ *	   while ((dev = class_dev_iter_next(&iter))
+ *                                                             devcd_del()
+ *                                                               device_del()
+ *                                                                 put_device() <- last reference
+ *             error = fn(dev, data)                           devcd_dev_release()
+ *             devcd_free(dev, data)                           kfree(devcd)
+ *             mutex_lock(&devcd->mutex);
+ *
+ *
+ * In the above diagram, It looks like disabled_store() would be racing with parallely
+ * running devcd_del() and result in memory abort while acquiring devcd->mutex which
+ * is called after kfree of devcd memory  after dropping its last reference with
+ * put_device(). However, this will not happens as fn(dev, data) runs
+ * with its own reference to device via klist_node so it is not its last reference.
+ * so, above situation would not occur.
+ */
+
 static ssize_t disabled_store(struct class *class, struct class_attribute *attr,
 			      const char *buf, size_t count)
 {
@@ -278,13 +353,17 @@
 	devcd->read = read;
 	devcd->free = free;
 	devcd->failing_dev = get_device(dev);
+	devcd->delete_work = false;
 
+	mutex_init(&devcd->mutex);
 	device_initialize(&devcd->devcd_dev);
 
 	dev_set_name(&devcd->devcd_dev, "devcd%d",
 		     atomic_inc_return(&devcd_count));
 	devcd->devcd_dev.class = &devcd_class;
 
+	mutex_lock(&devcd->mutex);
+	dev_set_uevent_suppress(&devcd->devcd_dev, true);
 	if (device_add(&devcd->devcd_dev))
 		goto put_device;
 
@@ -299,12 +378,15 @@
 		              "devcoredump"))
 		dev_warn(dev, "devcoredump create_link failed\n");
 
+	dev_set_uevent_suppress(&devcd->devcd_dev, false);
+	kobject_uevent(&devcd->devcd_dev.kobj, KOBJ_ADD);
 	INIT_DELAYED_WORK(&devcd->del_wk, devcd_del);
 	schedule_delayed_work(&devcd->del_wk, DEVCD_TIMEOUT);
-
+	mutex_unlock(&devcd->mutex);
 	return;
  put_device:
 	put_device(&devcd->devcd_dev);
+	mutex_unlock(&devcd->mutex);
  put_module:
 	module_put(owner);
  free:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/devres.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/devres.c
@@ -562,6 +562,7 @@
 	grp->id = grp;
 	if (id)
 		grp->id = id;
+	grp->color = 0;
 
 	spin_lock_irqsave(&dev->devres_lock, flags);
 	add_dr(dev, &grp->node[0]);
@@ -890,9 +891,12 @@
 	/*
 	 * Otherwise: allocate new, larger chunk. We need to allocate before
 	 * taking the lock as most probably the caller uses GFP_KERNEL.
+	 * alloc_dr() will call check_dr_size() to reserve extra memory
+	 * for struct devres automatically, so size @new_size user request
+	 * is delivered to it directly as devm_kmalloc() does.
 	 */
 	new_dr = alloc_dr(devm_kmalloc_release,
-			  total_new_size, gfp, dev_to_node(dev));
+			  new_size, gfp, dev_to_node(dev));
 	if (!new_dr)
 		return NULL;
 
@@ -1216,7 +1220,11 @@
  */
 void devm_free_percpu(struct device *dev, void __percpu *pdata)
 {
-	WARN_ON(devres_destroy(dev, devm_percpu_release, devm_percpu_match,
+	/*
+	 * Use devres_release() to prevent memory leakage as
+	 * devm_free_pages() does.
+	 */
+	WARN_ON(devres_release(dev, devm_percpu_release, devm_percpu_match,
 			       (__force void *)pdata));
 }
 EXPORT_SYMBOL_GPL(devm_free_percpu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/devtmpfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/devtmpfs.c
@@ -59,8 +59,15 @@
 		      const char *dev_name, void *data)
 {
 	struct super_block *s = mnt->mnt_sb;
+	int err;
+
 	atomic_inc(&s->s_active);
 	down_write(&s->s_umount);
+	err = reconfigure_single(s, flags, data);
+	if (err < 0) {
+		deactivate_locked_super(s);
+		return ERR_PTR(err);
+	}
 	return dget(s->s_root);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/driver.c
@@ -31,6 +31,75 @@
 }
 
 /**
+ * driver_set_override() - Helper to set or clear driver override.
+ * @dev: Device to change
+ * @override: Address of string to change (e.g. &device->driver_override);
+ *            The contents will be freed and hold newly allocated override.
+ * @s: NUL-terminated string, new driver name to force a match, pass empty
+ *     string to clear it ("" or "\n", where the latter is only for sysfs
+ *     interface).
+ * @len: length of @s
+ *
+ * Helper to set or clear driver override in a device, intended for the cases
+ * when the driver_override field is allocated by driver/bus code.
+ *
+ * Returns: 0 on success or a negative error code on failure.
+ */
+int driver_set_override(struct device *dev, const char **override,
+			const char *s, size_t len)
+{
+	const char *new, *old;
+	char *cp;
+
+	if (!override || !s)
+		return -EINVAL;
+
+	/*
+	 * The stored value will be used in sysfs show callback (sysfs_emit()),
+	 * which has a length limit of PAGE_SIZE and adds a trailing newline.
+	 * Thus we can store one character less to avoid truncation during sysfs
+	 * show.
+	 */
+	if (len >= (PAGE_SIZE - 1))
+		return -EINVAL;
+
+	if (!len) {
+		/* Empty string passed - clear override */
+		device_lock(dev);
+		old = *override;
+		*override = NULL;
+		device_unlock(dev);
+		kfree(old);
+
+		return 0;
+	}
+
+	cp = strnchr(s, len, '\n');
+	if (cp)
+		len = cp - s;
+
+	new = kstrndup(s, len, GFP_KERNEL);
+	if (!new)
+		return -ENOMEM;
+
+	device_lock(dev);
+	old = *override;
+	if (cp != s) {
+		*override = new;
+	} else {
+		/* "\n" passed - clear override */
+		kfree(new);
+		*override = NULL;
+	}
+	device_unlock(dev);
+
+	kfree(old);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(driver_set_override);
+
+/**
  * driver_for_each_device - Iterator for devices bound to a driver.
  * @drv: Driver we're iterating.
  * @start: Device to begin with
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/firmware_loader/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/firmware_loader/Kconfig
@@ -60,6 +60,8 @@
 	  image since it combines both GPL and non-GPL work. You should
 	  consult a lawyer of your own before distributing such an image.
 
+	  NOTE: Compressed files are not supported in EXTRA_FIRMWARE.
+
 config EXTRA_FIRMWARE_DIR
 	string "Firmware blobs root directory"
 	depends on EXTRA_FIRMWARE != ""
@@ -157,17 +159,32 @@
 
 config FW_LOADER_COMPRESS
 	bool "Enable compressed firmware support"
-	select FW_LOADER_PAGED_BUF
-	select XZ_DEC
 	help
 	  This option enables the support for loading compressed firmware
 	  files. The caller of firmware API receives the decompressed file
 	  content. The compressed file is loaded as a fallback, only after
 	  loading the raw file failed at first.
 
-	  Currently only XZ-compressed files are supported, and they have to
-	  be compressed with either none or crc32 integrity check type (pass
-	  "-C crc32" option to xz command).
+	  Compressed firmware support does not apply to firmware images
+	  that are built into the kernel image (CONFIG_EXTRA_FIRMWARE).
+
+if FW_LOADER_COMPRESS
+config FW_LOADER_COMPRESS_XZ
+	bool "Enable XZ-compressed firmware support"
+	select FW_LOADER_PAGED_BUF
+	select XZ_DEC
+	help
+	  This option adds the support for XZ-compressed files.
+	  The files have to be compressed with either none or crc32
+	  integrity check type (pass "-C crc32" option to xz command).
+
+config FW_LOADER_COMPRESS_ZSTD
+	bool "Enable ZSTD-compressed firmware support"
+	select ZSTD_DECOMPRESS
+	help
+	  This option adds the support for ZSTD-compressed files.
+
+endif # FW_LOADER_COMPRESS
 
 config FW_CACHE
 	bool "Enable firmware caching during suspend"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/firmware_loader/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/firmware_loader/main.c
@@ -35,6 +35,7 @@
 #include <linux/syscore_ops.h>
 #include <linux/reboot.h>
 #include <linux/security.h>
+#include <linux/zstd.h>
 #include <linux/xz.h>
 
 #include <generated/utsrelease.h>
@@ -100,12 +101,15 @@
 extern struct builtin_fw __start_builtin_fw[];
 extern struct builtin_fw __end_builtin_fw[];
 
-static void fw_copy_to_prealloc_buf(struct firmware *fw,
+static bool fw_copy_to_prealloc_buf(struct firmware *fw,
 				    void *buf, size_t size)
 {
-	if (!buf || size < fw->size)
-		return;
+	if (!buf)
+		return true;
+	if (size < fw->size)
+		return false;
 	memcpy(buf, fw->data, fw->size);
+	return true;
 }
 
 static bool fw_get_builtin_firmware(struct firmware *fw, const char *name,
@@ -117,9 +121,7 @@
 		if (strcmp(name, b_fw->name) == 0) {
 			fw->size = b_fw->size;
 			fw->data = b_fw->data;
-			fw_copy_to_prealloc_buf(fw, buf, size);
-
-			return true;
+			return fw_copy_to_prealloc_buf(fw, buf, size);
 		}
 	}
 
@@ -364,9 +366,73 @@
 #endif
 
 /*
+ * ZSTD-compressed firmware support
+ */
+#ifdef CONFIG_FW_LOADER_COMPRESS_ZSTD
+static int fw_decompress_zstd(struct device *dev, struct fw_priv *fw_priv,
+			      size_t in_size, const void *in_buffer)
+{
+	size_t len, out_size, workspace_size;
+	void *workspace, *out_buf;
+	ZSTD_DCtx *ctx;
+	int err;
+
+	if (fw_priv->allocated_size) {
+		out_size = fw_priv->allocated_size;
+		out_buf = fw_priv->data;
+	} else {
+		ZSTD_frameParams params;
+
+		if (ZSTD_getFrameParams(&params, in_buffer, in_size) ||
+		    params.frameContentSize == ZSTD_CONTENTSIZE_UNKNOWN) {
+			dev_dbg(dev, "%s: invalid zstd header\n", __func__);
+			return -EINVAL;
+		}
+		out_size = params.frameContentSize;
+		out_buf = vzalloc(out_size);
+		if (!out_buf)
+			return -ENOMEM;
+	}
+
+	workspace_size = ZSTD_DCtxWorkspaceBound();
+	workspace = kvzalloc(workspace_size, GFP_KERNEL);
+	if (!workspace) {
+		err = -ENOMEM;
+		goto error;
+	}
+
+	ctx = ZSTD_initDCtx(workspace, workspace_size);
+	if (!ctx) {
+		dev_dbg(dev, "%s: failed to initialize context\n", __func__);
+		err = -EINVAL;
+		goto error;
+	}
+
+	len = ZSTD_decompressDCtx(ctx, out_buf, out_size, in_buffer, in_size);
+	if (ZSTD_isError(len)) {
+		dev_dbg(dev, "%s: failed to decompress: %d\n", __func__,
+			ZSTD_getErrorCode(len));
+		err = -EINVAL;
+		goto error;
+	}
+
+	if (!fw_priv->allocated_size)
+		fw_priv->data = out_buf;
+	fw_priv->size = len;
+	err = 0;
+
+ error:
+	kvfree(workspace);
+	if (err && !fw_priv->allocated_size)
+		vfree(out_buf);
+	return err;
+}
+#endif /* CONFIG_FW_LOADER_COMPRESS_ZSTD */
+
+/*
  * XZ-compressed firmware support
  */
-#ifdef CONFIG_FW_LOADER_COMPRESS
+#ifdef CONFIG_FW_LOADER_COMPRESS_XZ
 /* show an error and return the standard error code */
 static int fw_decompress_xz_error(struct device *dev, enum xz_ret xz_ret)
 {
@@ -460,7 +526,7 @@
 	else
 		return fw_decompress_xz_pages(dev, fw_priv, in_size, in_buffer);
 }
-#endif /* CONFIG_FW_LOADER_COMPRESS */
+#endif /* CONFIG_FW_LOADER_COMPRESS_XZ */
 
 /* direct firmware loading support */
 static char fw_path_para[256];
@@ -787,6 +853,26 @@
 	mutex_unlock(&fw_lock);
 }
 
+/*
+ * Reject firmware file names with ".." path components.
+ * There are drivers that construct firmware file names from device-supplied
+ * strings, and we don't want some device to be able to tell us "I would like to
+ * be sent my firmware from ../../../etc/shadow, please".
+ *
+ * Search for ".." surrounded by either '/' or start/end of string.
+ *
+ * This intentionally only looks at the firmware name, not at the firmware base
+ * directory or at symlink contents.
+ */
+static bool name_contains_dotdot(const char *name)
+{
+	size_t name_len = strlen(name);
+
+	return strcmp(name, "..") == 0 || strncmp(name, "../", 3) == 0 ||
+	       strstr(name, "/../") != NULL ||
+	       (name_len >= 3 && strcmp(name+name_len-3, "/..") == 0);
+}
+
 /* called from request_firmware() and request_firmware_work_func() */
 static int
 _request_firmware(const struct firmware **firmware_p, const char *name,
@@ -794,6 +880,8 @@
 		  size_t offset, u32 opt_flags)
 {
 	struct firmware *fw = NULL;
+	struct cred *kern_cred = NULL;
+	const struct cred *old_cred;
 	bool nondirect = false;
 	int ret;
 
@@ -805,18 +893,43 @@
 		goto out;
 	}
 
+	if (name_contains_dotdot(name)) {
+		dev_warn(device,
+			 "Firmware load for '%s' refused, path contains '..' component\n",
+			 name);
+		ret = -EINVAL;
+		goto out;
+	}
+
 	ret = _request_firmware_prepare(&fw, name, device, buf, size,
 					offset, opt_flags);
 	if (ret <= 0) /* error or already assigned */
 		goto out;
 
+	/*
+	 * We are about to try to access the firmware file. Because we may have been
+	 * called by a driver when serving an unrelated request from userland, we use
+	 * the kernel credentials to read the file.
+	 */
+	kern_cred = prepare_kernel_cred(NULL);
+	if (!kern_cred) {
+		ret = -ENOMEM;
+		goto out;
+	}
+	old_cred = override_creds(kern_cred);
+
 	ret = fw_get_filesystem_firmware(device, fw->priv, "", NULL);
 
 	/* Only full reads can support decompression, platform, and sysfs. */
 	if (!(opt_flags & FW_OPT_PARTIAL))
 		nondirect = true;
 
-#ifdef CONFIG_FW_LOADER_COMPRESS
+#ifdef CONFIG_FW_LOADER_COMPRESS_ZSTD
+	if (ret == -ENOENT && nondirect)
+		ret = fw_get_filesystem_firmware(device, fw->priv, ".zst",
+						 fw_decompress_zstd);
+#endif
+#ifdef CONFIG_FW_LOADER_COMPRESS_XZ
 	if (ret == -ENOENT && nondirect)
 		ret = fw_get_filesystem_firmware(device, fw->priv, ".xz",
 						 fw_decompress_xz);
@@ -835,6 +948,9 @@
 	} else
 		ret = assign_fw(fw, device);
 
+	revert_creds(old_cred);
+	put_cred(kern_cred);
+
  out:
 	if (ret < 0) {
 		fw_abort_batch_reqs(fw);
@@ -860,6 +976,8 @@
  *      @name will be used as $FIRMWARE in the uevent environment and
  *      should be distinctive enough not to be confused with any other
  *      firmware image for this or any other device.
+ *	It must not contain any ".." path components - "foo/bar..bin" is
+ *	allowed, but "foo/../bar.bin" is not.
  *
  *	Caller must hold the reference count of @device.
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/init.c
@@ -8,6 +8,7 @@
 #include <linux/init.h>
 #include <linux/memory.h>
 #include <linux/of.h>
+#include <linux/backing-dev.h>
 
 #include "base.h"
 
@@ -20,6 +21,7 @@
 void __init driver_init(void)
 {
 	/* These are the core pieces */
+	bdi_init(&noop_backing_dev_info);
 	devtmpfs_init();
 	devices_init();
 	buses_init();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/memory.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/memory.c
@@ -555,6 +555,8 @@
 		return -EINVAL;
 	pfn >>= PAGE_SHIFT;
 	ret = memory_failure(pfn, 0);
+	if (ret == -EOPNOTSUPP)
+		ret = 0;
 	return ret ? ret : count;
 }
 
@@ -634,10 +636,9 @@
 	}
 	ret = xa_err(xa_store(&memory_blocks, memory->dev.id, memory,
 			      GFP_KERNEL));
-	if (ret) {
-		put_device(&memory->dev);
+	if (ret)
 		device_unregister(&memory->dev);
-	}
+
 	return ret;
 }
 
@@ -663,14 +664,16 @@
 	mem->nr_vmemmap_pages = nr_vmemmap_pages;
 	INIT_LIST_HEAD(&mem->group_next);
 
+	ret = register_memory(mem);
+	if (ret)
+		return ret;
+
 	if (group) {
 		mem->group = group;
 		list_add(&mem->group_next, &group->memory_blocks);
 	}
 
-	ret = register_memory(mem);
-
-	return ret;
+	return 0;
 }
 
 static int add_memory_block(unsigned long base_section_nr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/node.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/node.c
@@ -45,7 +45,7 @@
 	return n;
 }
 
-static BIN_ATTR_RO(cpumap, 0);
+static BIN_ATTR_RO(cpumap, CPUMAP_FILE_MAX_BYTES);
 
 static inline ssize_t cpulist_read(struct file *file, struct kobject *kobj,
 				   struct bin_attribute *attr, char *buf,
@@ -66,7 +66,7 @@
 	return n;
 }
 
-static BIN_ATTR_RO(cpulist, 0);
+static BIN_ATTR_RO(cpulist, CPULIST_FILE_MAX_BYTES);
 
 /**
  * struct node_access_nodes - Access class device to hold user visible
@@ -679,6 +679,7 @@
  */
 void unregister_node(struct node *node)
 {
+	compaction_unregister_node(node);
 	hugetlb_unregister_node(node);		/* no-op, if memoryless node */
 	node_remove_accesses(node);
 	node_remove_caches(node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/platform.c
@@ -1270,31 +1270,11 @@
 				     const char *buf, size_t count)
 {
 	struct platform_device *pdev = to_platform_device(dev);
-	char *driver_override, *old, *cp;
-
-	/* We need to keep extra room for a newline */
-	if (count >= (PAGE_SIZE - 1))
-		return -EINVAL;
-
-	driver_override = kstrndup(buf, count, GFP_KERNEL);
-	if (!driver_override)
-		return -ENOMEM;
-
-	cp = strchr(driver_override, '\n');
-	if (cp)
-		*cp = '\0';
-
-	device_lock(dev);
-	old = pdev->driver_override;
-	if (strlen(driver_override)) {
-		pdev->driver_override = driver_override;
-	} else {
-		kfree(driver_override);
-		pdev->driver_override = NULL;
-	}
-	device_unlock(dev);
+	int ret;
 
-	kfree(old);
+	ret = driver_set_override(dev, &pdev->driver_override, buf, count);
+	if (ret)
+		return ret;
 
 	return count;
 }
@@ -1427,7 +1407,9 @@
 	struct platform_driver *drv = to_platform_driver(_dev->driver);
 	struct platform_device *dev = to_platform_device(_dev);
 
-	if (drv->remove) {
+	if (drv->remove_new) {
+		drv->remove_new(dev);
+	} else if (drv->remove) {
 		int ret = drv->remove(dev);
 
 		if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/domain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/domain.c
@@ -217,10 +217,10 @@
 
 static void genpd_debug_remove(struct generic_pm_domain *genpd)
 {
-	struct dentry *d;
+	if (!genpd_debugfs_dir)
+		return;
 
-	d = debugfs_lookup(genpd->name, genpd_debugfs_dir);
-	debugfs_remove(d);
+	debugfs_lookup_and_remove(genpd->name, genpd_debugfs_dir);
 }
 
 static void genpd_update_accounting(struct generic_pm_domain *genpd)
@@ -1044,7 +1044,7 @@
 
 	return 0;
 }
-late_initcall(genpd_power_off_unused);
+late_initcall_sync(genpd_power_off_unused);
 
 #ifdef CONFIG_PM_SLEEP
 
@@ -1978,6 +1978,7 @@
 	genpd->device_count = 0;
 	genpd->max_off_time_ns = -1;
 	genpd->max_off_time_changed = true;
+	genpd->next_wakeup = KTIME_MAX;
 	genpd->provider = NULL;
 	genpd->has_provider = false;
 	genpd->accounting_time = ktime_get();
@@ -2058,9 +2059,9 @@
 		kfree(link);
 	}
 
-	genpd_debug_remove(genpd);
 	list_del(&genpd->gpd_list_node);
 	genpd_unlock(genpd);
+	genpd_debug_remove(genpd);
 	cancel_work_sync(&genpd->power_off_work);
 	if (genpd_is_cpu_domain(genpd))
 		free_cpumask_var(genpd->cpus);
@@ -2859,10 +2860,10 @@
 
 	err = of_property_read_u32(state_node, "min-residency-us", &residency);
 	if (!err)
-		genpd_state->residency_ns = 1000 * residency;
+		genpd_state->residency_ns = 1000LL * residency;
 
-	genpd_state->power_on_latency_ns = 1000 * exit_latency;
-	genpd_state->power_off_latency_ns = 1000 * entry_latency;
+	genpd_state->power_on_latency_ns = 1000LL * exit_latency;
+	genpd_state->power_off_latency_ns = 1000LL * entry_latency;
 	genpd_state->fwnode = &state_node->fwnode;
 
 	return 0;
@@ -2885,6 +2886,10 @@
 		np = it.node;
 		if (!of_match_node(idle_state_match, np))
 			continue;
+
+		if (!of_device_is_available(np))
+			continue;
+
 		if (states) {
 			ret = genpd_parse_state(&states[i], np);
 			if (ret) {
@@ -3048,7 +3053,7 @@
 	else
 		snprintf(state, sizeof(state), "%s",
 			 status_lookup[genpd->status]);
-	seq_printf(s, "%-30s  %-50s %u", genpd->name, state, genpd->performance_state);
+	seq_printf(s, "%-30s  %-49s  %u", genpd->name, state, genpd->performance_state);
 
 	/*
 	 * Modifications on the list require holding locks on both
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/main.c
@@ -580,7 +580,7 @@
 }
 
 /**
- * device_resume_noirq - Execute a "noirq resume" callback for given device.
+ * __device_resume_noirq - Execute a "noirq resume" callback for given device.
  * @dev: Device to handle.
  * @state: PM transition of the system being carried out.
  * @async: If true, the device is being resumed asynchronously.
@@ -588,7 +588,7 @@
  * The driver of @dev will not receive interrupts while this function is being
  * executed.
  */
-static int device_resume_noirq(struct device *dev, pm_message_t state, bool async)
+static void __device_resume_noirq(struct device *dev, pm_message_t state, bool async)
 {
 	pm_callback_t callback = NULL;
 	const char *info = NULL;
@@ -656,7 +656,13 @@
 Out:
 	complete_all(&dev->power.completion);
 	TRACE_RESUME(error);
-	return error;
+
+	if (error) {
+		suspend_stats.failed_resume_noirq++;
+		dpm_save_failed_step(SUSPEND_RESUME_NOIRQ);
+		dpm_save_failed_dev(dev_name(dev));
+		pm_dev_err(dev, state, async ? " async noirq" : " noirq", error);
+	}
 }
 
 static bool is_async(struct device *dev)
@@ -669,27 +675,35 @@
 {
 	reinit_completion(&dev->power.completion);
 
-	if (is_async(dev)) {
-		get_device(dev);
-		async_schedule_dev(func, dev);
+	if (!is_async(dev))
+		return false;
+
+	get_device(dev);
+
+	if (async_schedule_dev_nocall(func, dev))
 		return true;
-	}
+
+	put_device(dev);
 
 	return false;
 }
 
 static void async_resume_noirq(void *data, async_cookie_t cookie)
 {
-	struct device *dev = (struct device *)data;
-	int error;
-
-	error = device_resume_noirq(dev, pm_transition, true);
-	if (error)
-		pm_dev_err(dev, pm_transition, " async", error);
+	struct device *dev = data;
 
+	__device_resume_noirq(dev, pm_transition, true);
 	put_device(dev);
 }
 
+static void device_resume_noirq(struct device *dev)
+{
+	if (dpm_async_fn(dev, async_resume_noirq))
+		return;
+
+	__device_resume_noirq(dev, pm_transition, false);
+}
+
 static void dpm_noirq_resume_devices(pm_message_t state)
 {
 	struct device *dev;
@@ -699,34 +713,18 @@
 	mutex_lock(&dpm_list_mtx);
 	pm_transition = state;
 
-	/*
-	 * Advanced the async threads upfront,
-	 * in case the starting of async threads is
-	 * delayed by non-async resuming devices.
-	 */
-	list_for_each_entry(dev, &dpm_noirq_list, power.entry)
-		dpm_async_fn(dev, async_resume_noirq);
-
 	while (!list_empty(&dpm_noirq_list)) {
 		dev = to_device(dpm_noirq_list.next);
 		get_device(dev);
 		list_move_tail(&dev->power.entry, &dpm_late_early_list);
+
 		mutex_unlock(&dpm_list_mtx);
 
-		if (!is_async(dev)) {
-			int error;
+		device_resume_noirq(dev);
 
-			error = device_resume_noirq(dev, state, false);
-			if (error) {
-				suspend_stats.failed_resume_noirq++;
-				dpm_save_failed_step(SUSPEND_RESUME_NOIRQ);
-				dpm_save_failed_dev(dev_name(dev));
-				pm_dev_err(dev, state, " noirq", error);
-			}
-		}
+		put_device(dev);
 
 		mutex_lock(&dpm_list_mtx);
-		put_device(dev);
 	}
 	mutex_unlock(&dpm_list_mtx);
 	async_synchronize_full();
@@ -752,14 +750,14 @@
 }
 
 /**
- * device_resume_early - Execute an "early resume" callback for given device.
+ * __device_resume_early - Execute an "early resume" callback for given device.
  * @dev: Device to handle.
  * @state: PM transition of the system being carried out.
  * @async: If true, the device is being resumed asynchronously.
  *
  * Runtime PM is disabled for @dev while this function is being executed.
  */
-static int device_resume_early(struct device *dev, pm_message_t state, bool async)
+static void __device_resume_early(struct device *dev, pm_message_t state, bool async)
 {
 	pm_callback_t callback = NULL;
 	const char *info = NULL;
@@ -812,21 +810,31 @@
 
 	pm_runtime_enable(dev);
 	complete_all(&dev->power.completion);
-	return error;
+
+	if (error) {
+		suspend_stats.failed_resume_early++;
+		dpm_save_failed_step(SUSPEND_RESUME_EARLY);
+		dpm_save_failed_dev(dev_name(dev));
+		pm_dev_err(dev, state, async ? " async early" : " early", error);
+	}
 }
 
 static void async_resume_early(void *data, async_cookie_t cookie)
 {
-	struct device *dev = (struct device *)data;
-	int error;
-
-	error = device_resume_early(dev, pm_transition, true);
-	if (error)
-		pm_dev_err(dev, pm_transition, " async", error);
+	struct device *dev = data;
 
+	__device_resume_early(dev, pm_transition, true);
 	put_device(dev);
 }
 
+static void device_resume_early(struct device *dev)
+{
+	if (dpm_async_fn(dev, async_resume_early))
+		return;
+
+	__device_resume_early(dev, pm_transition, false);
+}
+
 /**
  * dpm_resume_early - Execute "early resume" callbacks for all devices.
  * @state: PM transition of the system being carried out.
@@ -840,33 +848,18 @@
 	mutex_lock(&dpm_list_mtx);
 	pm_transition = state;
 
-	/*
-	 * Advanced the async threads upfront,
-	 * in case the starting of async threads is
-	 * delayed by non-async resuming devices.
-	 */
-	list_for_each_entry(dev, &dpm_late_early_list, power.entry)
-		dpm_async_fn(dev, async_resume_early);
-
 	while (!list_empty(&dpm_late_early_list)) {
 		dev = to_device(dpm_late_early_list.next);
 		get_device(dev);
 		list_move_tail(&dev->power.entry, &dpm_suspended_list);
+
 		mutex_unlock(&dpm_list_mtx);
 
-		if (!is_async(dev)) {
-			int error;
+		device_resume_early(dev);
 
-			error = device_resume_early(dev, state, false);
-			if (error) {
-				suspend_stats.failed_resume_early++;
-				dpm_save_failed_step(SUSPEND_RESUME_EARLY);
-				dpm_save_failed_dev(dev_name(dev));
-				pm_dev_err(dev, state, " early", error);
-			}
-		}
-		mutex_lock(&dpm_list_mtx);
 		put_device(dev);
+
+		mutex_lock(&dpm_list_mtx);
 	}
 	mutex_unlock(&dpm_list_mtx);
 	async_synchronize_full();
@@ -886,12 +879,12 @@
 EXPORT_SYMBOL_GPL(dpm_resume_start);
 
 /**
- * device_resume - Execute "resume" callbacks for given device.
+ * __device_resume - Execute "resume" callbacks for given device.
  * @dev: Device to handle.
  * @state: PM transition of the system being carried out.
  * @async: If true, the device is being resumed asynchronously.
  */
-static int device_resume(struct device *dev, pm_message_t state, bool async)
+static void __device_resume(struct device *dev, pm_message_t state, bool async)
 {
 	pm_callback_t callback = NULL;
 	const char *info = NULL;
@@ -904,6 +897,9 @@
 	if (dev->power.syscore)
 		goto Complete;
 
+	if (!dev->power.is_suspended)
+		goto Complete;
+
 	if (dev->power.direct_complete) {
 		/* Match the pm_runtime_disable() in __device_suspend(). */
 		pm_runtime_enable(dev);
@@ -922,9 +918,6 @@
 	 */
 	dev->power.is_prepared = false;
 
-	if (!dev->power.is_suspended)
-		goto Unlock;
-
 	if (dev->pm_domain) {
 		info = "power domain ";
 		callback = pm_op(&dev->pm_domain->ops, state);
@@ -964,7 +957,6 @@
 	error = dpm_run_callback(callback, dev, state, info);
 	dev->power.is_suspended = false;
 
- Unlock:
 	device_unlock(dev);
 	dpm_watchdog_clear(&wd);
 
@@ -973,20 +965,30 @@
 
 	TRACE_RESUME(error);
 
-	return error;
+	if (error) {
+		suspend_stats.failed_resume++;
+		dpm_save_failed_step(SUSPEND_RESUME);
+		dpm_save_failed_dev(dev_name(dev));
+		pm_dev_err(dev, state, async ? " async" : "", error);
+	}
 }
 
 static void async_resume(void *data, async_cookie_t cookie)
 {
-	struct device *dev = (struct device *)data;
-	int error;
+	struct device *dev = data;
 
-	error = device_resume(dev, pm_transition, true);
-	if (error)
-		pm_dev_err(dev, pm_transition, " async", error);
+	__device_resume(dev, pm_transition, true);
 	put_device(dev);
 }
 
+static void device_resume(struct device *dev)
+{
+	if (dpm_async_fn(dev, async_resume))
+		return;
+
+	__device_resume(dev, pm_transition, false);
+}
+
 /**
  * dpm_resume - Execute "resume" callbacks for non-sysdev devices.
  * @state: PM transition of the system being carried out.
@@ -1006,30 +1008,25 @@
 	pm_transition = state;
 	async_error = 0;
 
-	list_for_each_entry(dev, &dpm_suspended_list, power.entry)
-		dpm_async_fn(dev, async_resume);
-
 	while (!list_empty(&dpm_suspended_list)) {
 		dev = to_device(dpm_suspended_list.next);
+
 		get_device(dev);
-		if (!is_async(dev)) {
-			int error;
 
-			mutex_unlock(&dpm_list_mtx);
+		mutex_unlock(&dpm_list_mtx);
 
-			error = device_resume(dev, state, false);
-			if (error) {
-				suspend_stats.failed_resume++;
-				dpm_save_failed_step(SUSPEND_RESUME);
-				dpm_save_failed_dev(dev_name(dev));
-				pm_dev_err(dev, state, "", error);
-			}
+		device_resume(dev);
+
+		mutex_lock(&dpm_list_mtx);
 
-			mutex_lock(&dpm_list_mtx);
-		}
 		if (!list_empty(&dev->power.entry))
 			list_move_tail(&dev->power.entry, &dpm_prepared_list);
+
+		mutex_unlock(&dpm_list_mtx);
+
 		put_device(dev);
+
+		mutex_lock(&dpm_list_mtx);
 	}
 	mutex_unlock(&dpm_list_mtx);
 	async_synchronize_full();
@@ -1051,7 +1048,7 @@
 	const char *info = NULL;
 
 	if (dev->power.syscore)
-		return;
+		goto out;
 
 	device_lock(dev);
 
@@ -1081,6 +1078,7 @@
 
 	device_unlock(dev);
 
+out:
 	pm_runtime_put(dev);
 }
 
@@ -1106,14 +1104,16 @@
 		get_device(dev);
 		dev->power.is_prepared = false;
 		list_move(&dev->power.entry, &list);
+
 		mutex_unlock(&dpm_list_mtx);
 
 		trace_device_pm_callback_start(dev, "", state.event);
 		device_complete(dev, state);
 		trace_device_pm_callback_end(dev, 0);
 
-		mutex_lock(&dpm_list_mtx);
 		put_device(dev);
+
+		mutex_lock(&dpm_list_mtx);
 	}
 	list_splice(&list, &dpm_list);
 	mutex_unlock(&dpm_list_mtx);
@@ -1238,14 +1238,13 @@
 	dev->power.is_noirq_suspended = true;
 
 	/*
-	 * Skipping the resume of devices that were in use right before the
-	 * system suspend (as indicated by their PM-runtime usage counters)
-	 * would be suboptimal.  Also resume them if doing that is not allowed
-	 * to be skipped.
+	 * Devices must be resumed unless they are explicitly allowed to be left
+	 * in suspend, but even in that case skipping the resume of devices that
+	 * were in use right before the system suspend (as indicated by their
+	 * runtime PM usage counters and child counters) would be suboptimal.
 	 */
-	if (atomic_read(&dev->power.usage_count) > 1 ||
-	    !(dev_pm_test_driver_flags(dev, DPM_FLAG_MAY_SKIP_RESUME) &&
-	      dev->power.may_skip_resume))
+	if (!(dev_pm_test_driver_flags(dev, DPM_FLAG_MAY_SKIP_RESUME) &&
+	      dev->power.may_skip_resume) || !pm_runtime_need_not_resume(dev))
 		dev->power.must_resume = true;
 
 	if (dev->power.must_resume)
@@ -1259,7 +1258,7 @@
 
 static void async_suspend_noirq(void *data, async_cookie_t cookie)
 {
-	struct device *dev = (struct device *)data;
+	struct device *dev = data;
 	int error;
 
 	error = __device_suspend_noirq(dev, pm_transition, true);
@@ -1298,17 +1297,21 @@
 		error = device_suspend_noirq(dev);
 
 		mutex_lock(&dpm_list_mtx);
+
 		if (error) {
 			pm_dev_err(dev, state, " noirq", error);
 			dpm_save_failed_dev(dev_name(dev));
-			put_device(dev);
-			break;
-		}
-		if (!list_empty(&dev->power.entry))
+		} else if (!list_empty(&dev->power.entry)) {
 			list_move(&dev->power.entry, &dpm_noirq_list);
+		}
+
+		mutex_unlock(&dpm_list_mtx);
+
 		put_device(dev);
 
-		if (async_error)
+		mutex_lock(&dpm_list_mtx);
+
+		if (error || async_error)
 			break;
 	}
 	mutex_unlock(&dpm_list_mtx);
@@ -1438,7 +1441,7 @@
 
 static void async_suspend_late(void *data, async_cookie_t cookie)
 {
-	struct device *dev = (struct device *)data;
+	struct device *dev = data;
 	int error;
 
 	error = __device_suspend_late(dev, pm_transition, true);
@@ -1475,23 +1478,28 @@
 		struct device *dev = to_device(dpm_suspended_list.prev);
 
 		get_device(dev);
+
 		mutex_unlock(&dpm_list_mtx);
 
 		error = device_suspend_late(dev);
 
 		mutex_lock(&dpm_list_mtx);
+
 		if (!list_empty(&dev->power.entry))
 			list_move(&dev->power.entry, &dpm_late_early_list);
 
 		if (error) {
 			pm_dev_err(dev, state, " late", error);
 			dpm_save_failed_dev(dev_name(dev));
-			put_device(dev);
-			break;
 		}
+
+		mutex_unlock(&dpm_list_mtx);
+
 		put_device(dev);
 
-		if (async_error)
+		mutex_lock(&dpm_list_mtx);
+
+		if (error || async_error)
 			break;
 	}
 	mutex_unlock(&dpm_list_mtx);
@@ -1633,6 +1641,7 @@
 			pm_runtime_disable(dev);
 			if (pm_runtime_status_suspended(dev)) {
 				pm_dev_dbg(dev, state, "direct-complete ");
+				dev->power.is_suspended = true;
 				goto Complete;
 			}
 
@@ -1709,7 +1718,7 @@
 
 static void async_suspend(void *data, async_cookie_t cookie)
 {
-	struct device *dev = (struct device *)data;
+	struct device *dev = data;
 	int error;
 
 	error = __device_suspend(dev, pm_transition, true);
@@ -1751,21 +1760,27 @@
 		struct device *dev = to_device(dpm_prepared_list.prev);
 
 		get_device(dev);
+
 		mutex_unlock(&dpm_list_mtx);
 
 		error = device_suspend(dev);
 
 		mutex_lock(&dpm_list_mtx);
+
 		if (error) {
 			pm_dev_err(dev, state, "", error);
 			dpm_save_failed_dev(dev_name(dev));
-			put_device(dev);
-			break;
-		}
-		if (!list_empty(&dev->power.entry))
+		} else if (!list_empty(&dev->power.entry)) {
 			list_move(&dev->power.entry, &dpm_suspended_list);
+		}
+
+		mutex_unlock(&dpm_list_mtx);
+
 		put_device(dev);
-		if (async_error)
+
+		mutex_lock(&dpm_list_mtx);
+
+		if (error || async_error)
 			break;
 	}
 	mutex_unlock(&dpm_list_mtx);
@@ -1794,9 +1809,6 @@
 	int (*callback)(struct device *) = NULL;
 	int ret = 0;
 
-	if (dev->power.syscore)
-		return 0;
-
 	/*
 	 * If a device's parent goes into runtime suspend at the wrong time,
 	 * it won't be possible to resume the device.  To prevent this we
@@ -1805,6 +1817,9 @@
 	 */
 	pm_runtime_get_noresume(dev);
 
+	if (dev->power.syscore)
+		return 0;
+
 	device_lock(dev);
 
 	dev->power.wakeup_path = false;
@@ -1878,10 +1893,11 @@
 	device_block_probing();
 
 	mutex_lock(&dpm_list_mtx);
-	while (!list_empty(&dpm_list)) {
+	while (!list_empty(&dpm_list) && !error) {
 		struct device *dev = to_device(dpm_list.next);
 
 		get_device(dev);
+
 		mutex_unlock(&dpm_list_mtx);
 
 		trace_device_pm_callback_start(dev, "", state.event);
@@ -1889,21 +1905,23 @@
 		trace_device_pm_callback_end(dev, error);
 
 		mutex_lock(&dpm_list_mtx);
-		if (error) {
-			if (error == -EAGAIN) {
-				put_device(dev);
-				error = 0;
-				continue;
-			}
+
+		if (!error) {
+			dev->power.is_prepared = true;
+			if (!list_empty(&dev->power.entry))
+				list_move_tail(&dev->power.entry, &dpm_prepared_list);
+		} else if (error == -EAGAIN) {
+			error = 0;
+		} else {
 			dev_info(dev, "not prepared for power transition: code %d\n",
 				 error);
-			put_device(dev);
-			break;
 		}
-		dev->power.is_prepared = true;
-		if (!list_empty(&dev->power.entry))
-			list_move_tail(&dev->power.entry, &dpm_prepared_list);
+
+		mutex_unlock(&dpm_list_mtx);
+
 		put_device(dev);
+
+		mutex_lock(&dpm_list_mtx);
 	}
 	mutex_unlock(&dpm_list_mtx);
 	trace_suspend_resume(TPS("dpm_prepare"), state.event, false);
@@ -1991,7 +2009,9 @@
 
 void device_pm_check_callbacks(struct device *dev)
 {
-	spin_lock_irq(&dev->power.lock);
+	unsigned long flags;
+
+	spin_lock_irqsave(&dev->power.lock, flags);
 	dev->power.no_pm_callbacks =
 		(!dev->bus || (pm_ops_is_empty(dev->bus->pm) &&
 		 !dev->bus->suspend && !dev->bus->resume)) &&
@@ -2000,7 +2020,7 @@
 		(!dev->pm_domain || pm_ops_is_empty(&dev->pm_domain->ops)) &&
 		(!dev->driver || (pm_ops_is_empty(dev->driver->pm) &&
 		 !dev->driver->suspend && !dev->driver->resume));
-	spin_unlock_irq(&dev->power.lock);
+	spin_unlock_irqrestore(&dev->power.lock, flags);
 }
 
 bool dev_pm_skip_suspend(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/power.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/power.h
@@ -25,8 +25,11 @@
 
 #define WAKE_IRQ_DEDICATED_ALLOCATED	BIT(0)
 #define WAKE_IRQ_DEDICATED_MANAGED	BIT(1)
+#define WAKE_IRQ_DEDICATED_REVERSE	BIT(2)
 #define WAKE_IRQ_DEDICATED_MASK		(WAKE_IRQ_DEDICATED_ALLOCATED | \
-					 WAKE_IRQ_DEDICATED_MANAGED)
+					 WAKE_IRQ_DEDICATED_MANAGED | \
+					 WAKE_IRQ_DEDICATED_REVERSE)
+#define WAKE_IRQ_DEDICATED_ENABLED	BIT(3)
 
 struct wake_irq {
 	struct device *dev;
@@ -39,7 +42,8 @@
 extern void dev_pm_disarm_wake_irq(struct wake_irq *wirq);
 extern void dev_pm_enable_wake_irq_check(struct device *dev,
 					 bool can_change_status);
-extern void dev_pm_disable_wake_irq_check(struct device *dev);
+extern void dev_pm_disable_wake_irq_check(struct device *dev, bool cond_disable);
+extern void dev_pm_enable_wake_irq_complete(struct device *dev);
 
 #ifdef CONFIG_PM_SLEEP
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/runtime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/runtime.c
@@ -305,16 +305,34 @@
 	return 0;
 }
 
+/**
+ * pm_runtime_release_supplier - Drop references to device link's supplier.
+ * @link: Target device link.
+ *
+ * Drop all runtime PM references associated with @link to its supplier device.
+ */
+void pm_runtime_release_supplier(struct device_link *link)
+{
+	struct device *supplier = link->supplier;
+
+	/*
+	 * The additional power.usage_count check is a safety net in case
+	 * the rpm_active refcount becomes saturated, in which case
+	 * refcount_dec_not_one() would return true forever, but it is not
+	 * strictly necessary.
+	 */
+	while (refcount_dec_not_one(&link->rpm_active) &&
+	       atomic_read(&supplier->power.usage_count) > 0)
+		pm_runtime_put_noidle(supplier);
+}
+
 static void __rpm_put_suppliers(struct device *dev, bool try_to_suspend)
 {
 	struct device_link *link;
 
 	list_for_each_entry_rcu(link, &dev->links.suppliers, c_node,
 				device_links_read_lock_held()) {
-
-		while (refcount_dec_not_one(&link->rpm_active))
-			pm_runtime_put_noidle(link->supplier);
-
+		pm_runtime_release_supplier(link);
 		if (try_to_suspend)
 			pm_request_idle(link->supplier);
 	}
@@ -466,7 +484,17 @@
 
 	dev->power.idle_notification = true;
 
-	retval = __rpm_callback(callback, dev);
+	if (dev->power.irq_safe)
+		spin_unlock(&dev->power.lock);
+	else
+		spin_unlock_irq(&dev->power.lock);
+
+	retval = callback(dev);
+
+	if (dev->power.irq_safe)
+		spin_lock(&dev->power.lock);
+	else
+		spin_lock_irq(&dev->power.lock);
 
 	dev->power.idle_notification = false;
 	wake_up_all(&dev->power.wait_queue);
@@ -645,6 +673,8 @@
 	if (retval)
 		goto fail;
 
+	dev_pm_enable_wake_irq_complete(dev);
+
  no_callback:
 	__update_runtime_status(dev, RPM_SUSPENDED);
 	pm_runtime_deactivate_timer(dev);
@@ -690,7 +720,7 @@
 	return retval;
 
  fail:
-	dev_pm_disable_wake_irq_check(dev);
+	dev_pm_disable_wake_irq_check(dev, true);
 	__update_runtime_status(dev, RPM_ACTIVE);
 	dev->power.deferred_resume = false;
 	wake_up_all(&dev->power.wait_queue);
@@ -873,7 +903,7 @@
 
 	callback = RPM_GET_CALLBACK(dev, runtime_resume);
 
-	dev_pm_disable_wake_irq_check(dev);
+	dev_pm_disable_wake_irq_check(dev, false);
 	retval = rpm_callback(callback, dev);
 	if (retval) {
 		__update_runtime_status(dev, RPM_SUSPENDED);
@@ -1449,11 +1479,16 @@
 
 static void pm_runtime_disable_action(void *data)
 {
+	pm_runtime_dont_use_autosuspend(data);
 	pm_runtime_disable(data);
 }
 
 /**
  * devm_pm_runtime_enable - devres-enabled version of pm_runtime_enable.
+ *
+ * NOTE: this will also handle calling pm_runtime_dont_use_autosuspend() for
+ * you at driver exit time if needed.
+ *
  * @dev: Device to handle.
  */
 int devm_pm_runtime_enable(struct device *dev)
@@ -1770,12 +1805,11 @@
 		return;
 
 	pm_runtime_drop_link_count(link->consumer);
-
-	while (refcount_dec_not_one(&link->rpm_active))
-		pm_runtime_put(link->supplier);
+	pm_runtime_release_supplier(link);
+	pm_request_idle(link->supplier);
 }
 
-static bool pm_runtime_need_not_resume(struct device *dev)
+bool pm_runtime_need_not_resume(struct device *dev)
 {
 	return atomic_read(&dev->power.usage_count) <= 1 &&
 		(atomic_read(&dev->power.child_count) == 0 ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/trace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/trace.c
@@ -120,7 +120,11 @@
 	struct rtc_time time;
 	unsigned int val;
 
-	mc146818_get_time(&time);
+	if (mc146818_get_time(&time) < 0) {
+		pr_err("Unable to read current time from RTC\n");
+		return 0;
+	}
+
 	pr_info("RTC time: %ptRt, date: %ptRd\n", &time, &time);
 	val = time.tm_year;				/* 100 years */
 	if (val > 100)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/wakeirq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/wakeirq.c
@@ -142,24 +142,7 @@
 	return IRQ_HANDLED;
 }
 
-/**
- * dev_pm_set_dedicated_wake_irq - Request a dedicated wake-up interrupt
- * @dev: Device entry
- * @irq: Device wake-up interrupt
- *
- * Unless your hardware has separate wake-up interrupts in addition
- * to the device IO interrupts, you don't need this.
- *
- * Sets up a threaded interrupt handler for a device that has
- * a dedicated wake-up interrupt in addition to the device IO
- * interrupt.
- *
- * The interrupt starts disabled, and needs to be managed for
- * the device by the bus code or the device driver using
- * dev_pm_enable_wake_irq() and dev_pm_disable_wake_irq()
- * functions.
- */
-int dev_pm_set_dedicated_wake_irq(struct device *dev, int irq)
+static int __dev_pm_set_dedicated_wake_irq(struct device *dev, int irq, unsigned int flag)
 {
 	struct wake_irq *wirq;
 	int err;
@@ -197,7 +180,7 @@
 	if (err)
 		goto err_free_irq;
 
-	wirq->status = WAKE_IRQ_DEDICATED_ALLOCATED;
+	wirq->status = WAKE_IRQ_DEDICATED_ALLOCATED | flag;
 
 	return err;
 
@@ -210,9 +193,58 @@
 
 	return err;
 }
+
+
+/**
+ * dev_pm_set_dedicated_wake_irq - Request a dedicated wake-up interrupt
+ * @dev: Device entry
+ * @irq: Device wake-up interrupt
+ *
+ * Unless your hardware has separate wake-up interrupts in addition
+ * to the device IO interrupts, you don't need this.
+ *
+ * Sets up a threaded interrupt handler for a device that has
+ * a dedicated wake-up interrupt in addition to the device IO
+ * interrupt.
+ *
+ * The interrupt starts disabled, and needs to be managed for
+ * the device by the bus code or the device driver using
+ * dev_pm_enable_wake_irq*() and dev_pm_disable_wake_irq*()
+ * functions.
+ */
+int dev_pm_set_dedicated_wake_irq(struct device *dev, int irq)
+{
+	return __dev_pm_set_dedicated_wake_irq(dev, irq, 0);
+}
 EXPORT_SYMBOL_GPL(dev_pm_set_dedicated_wake_irq);
 
 /**
+ * dev_pm_set_dedicated_wake_irq_reverse - Request a dedicated wake-up interrupt
+ *                                         with reverse enable ordering
+ * @dev: Device entry
+ * @irq: Device wake-up interrupt
+ *
+ * Unless your hardware has separate wake-up interrupts in addition
+ * to the device IO interrupts, you don't need this.
+ *
+ * Sets up a threaded interrupt handler for a device that has a dedicated
+ * wake-up interrupt in addition to the device IO interrupt. It sets
+ * the status of WAKE_IRQ_DEDICATED_REVERSE to tell rpm_suspend()
+ * to enable dedicated wake-up interrupt after running the runtime suspend
+ * callback for @dev.
+ *
+ * The interrupt starts disabled, and needs to be managed for
+ * the device by the bus code or the device driver using
+ * dev_pm_enable_wake_irq*() and dev_pm_disable_wake_irq*()
+ * functions.
+ */
+int dev_pm_set_dedicated_wake_irq_reverse(struct device *dev, int irq)
+{
+	return __dev_pm_set_dedicated_wake_irq(dev, irq, WAKE_IRQ_DEDICATED_REVERSE);
+}
+EXPORT_SYMBOL_GPL(dev_pm_set_dedicated_wake_irq_reverse);
+
+/**
  * dev_pm_enable_wake_irq - Enable device wake-up interrupt
  * @dev: Device
  *
@@ -282,25 +314,58 @@
 	return;
 
 enable:
-	enable_irq(wirq->irq);
+	if (!can_change_status || !(wirq->status & WAKE_IRQ_DEDICATED_REVERSE)) {
+		enable_irq(wirq->irq);
+		wirq->status |= WAKE_IRQ_DEDICATED_ENABLED;
+	}
 }
 
 /**
  * dev_pm_disable_wake_irq_check - Checks and disables wake-up interrupt
  * @dev: Device
+ * @cond_disable: if set, also check WAKE_IRQ_DEDICATED_REVERSE
  *
  * Disables wake-up interrupt conditionally based on status.
  * Should be only called from rpm_suspend() and rpm_resume() path.
  */
-void dev_pm_disable_wake_irq_check(struct device *dev)
+void dev_pm_disable_wake_irq_check(struct device *dev, bool cond_disable)
 {
 	struct wake_irq *wirq = dev->power.wakeirq;
 
 	if (!wirq || !(wirq->status & WAKE_IRQ_DEDICATED_MASK))
 		return;
 
-	if (wirq->status & WAKE_IRQ_DEDICATED_MANAGED)
+	if (cond_disable && (wirq->status & WAKE_IRQ_DEDICATED_REVERSE))
+		return;
+
+	if (wirq->status & WAKE_IRQ_DEDICATED_MANAGED) {
+		wirq->status &= ~WAKE_IRQ_DEDICATED_ENABLED;
 		disable_irq_nosync(wirq->irq);
+	}
+}
+
+/**
+ * dev_pm_enable_wake_irq_complete - enable wake IRQ not enabled before
+ * @dev: Device using the wake IRQ
+ *
+ * Enable wake IRQ conditionally based on status, mainly used if want to
+ * enable wake IRQ after running ->runtime_suspend() which depends on
+ * WAKE_IRQ_DEDICATED_REVERSE.
+ *
+ * Should be only called from rpm_suspend() path.
+ */
+void dev_pm_enable_wake_irq_complete(struct device *dev)
+{
+	struct wake_irq *wirq = dev->power.wakeirq;
+
+	if (!wirq || !(wirq->status & WAKE_IRQ_DEDICATED_MASK))
+		return;
+
+	if (wirq->status & WAKE_IRQ_DEDICATED_MANAGED &&
+	    wirq->status & WAKE_IRQ_DEDICATED_REVERSE) {
+		enable_irq(wirq->irq);
+		wirq->status |= WAKE_IRQ_DEDICATED_ENABLED;
+	}
 }
 
 /**
@@ -317,7 +382,7 @@
 
 	if (device_may_wakeup(wirq->dev)) {
 		if (wirq->status & WAKE_IRQ_DEDICATED_ALLOCATED &&
-		    !pm_runtime_status_suspended(wirq->dev))
+		    !(wirq->status & WAKE_IRQ_DEDICATED_ENABLED))
 			enable_irq(wirq->irq);
 
 		enable_irq_wake(wirq->irq);
@@ -340,7 +405,7 @@
 		disable_irq_wake(wirq->irq);
 
 		if (wirq->status & WAKE_IRQ_DEDICATED_ALLOCATED &&
-		    !pm_runtime_status_suspended(wirq->dev))
+		    !(wirq->status & WAKE_IRQ_DEDICATED_ENABLED))
 			disable_irq_nosync(wirq->irq);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/power/wakeup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/power/wakeup.c
@@ -34,7 +34,8 @@
 bool events_check_enabled __read_mostly;
 
 /* First wakeup IRQ seen by the kernel in the last cycle. */
-unsigned int pm_wakeup_irq __read_mostly;
+static unsigned int wakeup_irq[2] __read_mostly;
+static DEFINE_RAW_SPINLOCK(wakeup_irq_lock);
 
 /* If greater than 0 and the system is suspending, terminate the suspend. */
 static atomic_t pm_abort_suspend __read_mostly;
@@ -942,19 +943,45 @@
 	atomic_dec_if_positive(&pm_abort_suspend);
 }
 
-void pm_wakeup_clear(bool reset)
+void pm_wakeup_clear(unsigned int irq_number)
 {
-	pm_wakeup_irq = 0;
-	if (reset)
+	raw_spin_lock_irq(&wakeup_irq_lock);
+
+	if (irq_number && wakeup_irq[0] == irq_number)
+		wakeup_irq[0] = wakeup_irq[1];
+	else
+		wakeup_irq[0] = 0;
+
+	wakeup_irq[1] = 0;
+
+	raw_spin_unlock_irq(&wakeup_irq_lock);
+
+	if (!irq_number)
 		atomic_set(&pm_abort_suspend, 0);
 }
 
 void pm_system_irq_wakeup(unsigned int irq_number)
 {
-	if (pm_wakeup_irq == 0) {
-		pm_wakeup_irq = irq_number;
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&wakeup_irq_lock, flags);
+
+	if (wakeup_irq[0] == 0)
+		wakeup_irq[0] = irq_number;
+	else if (wakeup_irq[1] == 0)
+		wakeup_irq[1] = irq_number;
+	else
+		irq_number = 0;
+
+	raw_spin_unlock_irqrestore(&wakeup_irq_lock, flags);
+
+	if (irq_number)
 		pm_system_wakeup();
-	}
+}
+
+unsigned int pm_wakeup_irq(void)
+{
+	return wakeup_irq[0];
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/property.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/property.c
@@ -18,12 +18,19 @@
 #include <linux/etherdevice.h>
 #include <linux/phy.h>
 
-struct fwnode_handle *dev_fwnode(struct device *dev)
+struct fwnode_handle *__dev_fwnode(struct device *dev)
 {
 	return IS_ENABLED(CONFIG_OF) && dev->of_node ?
 		of_fwnode_handle(dev->of_node) : dev->fwnode;
 }
-EXPORT_SYMBOL_GPL(dev_fwnode);
+EXPORT_SYMBOL_GPL(__dev_fwnode);
+
+const struct fwnode_handle *__dev_fwnode_const(const struct device *dev)
+{
+	return IS_ENABLED(CONFIG_OF) && dev->of_node ?
+		of_fwnode_handle(dev->of_node) : dev->fwnode;
+}
+EXPORT_SYMBOL_GPL(__dev_fwnode_const);
 
 /**
  * device_property_present - check if a property of a device is present
@@ -48,12 +55,14 @@
 {
 	bool ret;
 
+	if (IS_ERR_OR_NULL(fwnode))
+		return false;
+
 	ret = fwnode_call_bool_op(fwnode, property_present, propname);
-	if (ret == false && !IS_ERR_OR_NULL(fwnode) &&
-	    !IS_ERR_OR_NULL(fwnode->secondary))
-		ret = fwnode_call_bool_op(fwnode->secondary, property_present,
-					 propname);
-	return ret;
+	if (ret)
+		return ret;
+
+	return fwnode_call_bool_op(fwnode->secondary, property_present, propname);
 }
 EXPORT_SYMBOL_GPL(fwnode_property_present);
 
@@ -233,15 +242,16 @@
 {
 	int ret;
 
+	if (IS_ERR_OR_NULL(fwnode))
+		return -EINVAL;
+
 	ret = fwnode_call_int_op(fwnode, property_read_int_array, propname,
 				 elem_size, val, nval);
-	if (ret == -EINVAL && !IS_ERR_OR_NULL(fwnode) &&
-	    !IS_ERR_OR_NULL(fwnode->secondary))
-		ret = fwnode_call_int_op(
-			fwnode->secondary, property_read_int_array, propname,
-			elem_size, val, nval);
+	if (ret != -EINVAL)
+		return ret;
 
-	return ret;
+	return fwnode_call_int_op(fwnode->secondary, property_read_int_array, propname,
+				  elem_size, val, nval);
 }
 
 /**
@@ -372,14 +382,16 @@
 {
 	int ret;
 
+	if (IS_ERR_OR_NULL(fwnode))
+		return -EINVAL;
+
 	ret = fwnode_call_int_op(fwnode, property_read_string_array, propname,
 				 val, nval);
-	if (ret == -EINVAL && !IS_ERR_OR_NULL(fwnode) &&
-	    !IS_ERR_OR_NULL(fwnode->secondary))
-		ret = fwnode_call_int_op(fwnode->secondary,
-					 property_read_string_array, propname,
-					 val, nval);
-	return ret;
+	if (ret != -EINVAL)
+		return ret;
+
+	return fwnode_call_int_op(fwnode->secondary, property_read_string_array, propname,
+				  val, nval);
 }
 EXPORT_SYMBOL_GPL(fwnode_property_read_string_array);
 
@@ -479,7 +491,20 @@
 				       unsigned int nargs, unsigned int index,
 				       struct fwnode_reference_args *args)
 {
-	return fwnode_call_int_op(fwnode, get_reference_args, prop, nargs_prop,
+	int ret;
+
+	if (IS_ERR_OR_NULL(fwnode))
+		return -ENOENT;
+
+	ret = fwnode_call_int_op(fwnode, get_reference_args, prop, nargs_prop,
+				 nargs, index, args);
+	if (ret == 0)
+		return ret;
+
+	if (IS_ERR_OR_NULL(fwnode->secondary))
+		return ret;
+
+	return fwnode_call_int_op(fwnode->secondary, get_reference_args, prop, nargs_prop,
 				  nargs, index, args);
 }
 EXPORT_SYMBOL_GPL(fwnode_property_get_reference_args);
@@ -675,12 +700,13 @@
 struct fwnode_handle *fwnode_get_nth_parent(struct fwnode_handle *fwnode,
 					    unsigned int depth)
 {
-	unsigned int i;
-
 	fwnode_handle_get(fwnode);
 
-	for (i = 0; i < depth && fwnode; i++)
+	do {
+		if (depth-- == 0)
+			break;
 		fwnode = fwnode_get_next_parent(fwnode);
+	} while (fwnode);
 
 	return fwnode;
 }
@@ -699,17 +725,17 @@
 bool fwnode_is_ancestor_of(struct fwnode_handle *test_ancestor,
 				  struct fwnode_handle *test_child)
 {
-	if (!test_ancestor)
+	if (IS_ERR_OR_NULL(test_ancestor))
 		return false;
 
 	fwnode_handle_get(test_child);
-	while (test_child) {
+	do {
 		if (test_child == test_ancestor) {
 			fwnode_handle_put(test_child);
 			return true;
 		}
 		test_child = fwnode_get_next_parent(test_child);
-	}
+	} while (test_child);
 	return false;
 }
 
@@ -738,7 +764,7 @@
 {
 	struct fwnode_handle *next_child = child;
 
-	if (!fwnode)
+	if (IS_ERR_OR_NULL(fwnode))
 		return NULL;
 
 	do {
@@ -762,16 +788,16 @@
 	const struct fwnode_handle *fwnode = dev_fwnode(dev);
 	struct fwnode_handle *next;
 
+	if (IS_ERR_OR_NULL(fwnode))
+		return NULL;
+
 	/* Try to find a child in primary fwnode */
 	next = fwnode_get_next_child_node(fwnode, child);
 	if (next)
 		return next;
 
 	/* When no more children in primary, continue with secondary */
-	if (fwnode && !IS_ERR_OR_NULL(fwnode->secondary))
-		next = fwnode_get_next_child_node(fwnode->secondary, child);
-
-	return next;
+	return fwnode_get_next_child_node(fwnode->secondary, child);
 }
 EXPORT_SYMBOL_GPL(device_get_next_child_node);
 
@@ -838,6 +864,9 @@
  */
 bool fwnode_device_is_available(const struct fwnode_handle *fwnode)
 {
+	if (IS_ERR_OR_NULL(fwnode))
+		return false;
+
 	if (!fwnode_has_op(fwnode, device_is_available))
 		return true;
 
@@ -1022,6 +1051,51 @@
 EXPORT_SYMBOL(fwnode_irq_get);
 
 /**
+ * fwnode_iomap - Maps the memory mapped IO for a given fwnode
+ * @fwnode:	Pointer to the firmware node
+ * @index:	Index of the IO range
+ *
+ * Returns a pointer to the mapped memory.
+ */
+void __iomem *fwnode_iomap(struct fwnode_handle *fwnode, int index)
+{
+	if (IS_ENABLED(CONFIG_OF_ADDRESS) && is_of_node(fwnode))
+		return of_iomap(to_of_node(fwnode), index);
+
+	return NULL;
+}
+EXPORT_SYMBOL(fwnode_iomap);
+
+/**
+ * fwnode_irq_get_byname - Get IRQ from a fwnode using its name
+ * @fwnode:	Pointer to the firmware node
+ * @name:	IRQ name
+ *
+ * Description:
+ * Find a match to the string @name in the 'interrupt-names' string array
+ * in _DSD for ACPI, or of_node for Device Tree. Then get the Linux IRQ
+ * number of the IRQ resource corresponding to the index of the matched
+ * string.
+ *
+ * Return:
+ * Linux IRQ number on success, or negative errno otherwise.
+ */
+int fwnode_irq_get_byname(const struct fwnode_handle *fwnode, const char *name)
+{
+	int index;
+
+	if (!name)
+		return -EINVAL;
+
+	index = fwnode_property_match_string(fwnode, "interrupt-names",  name);
+	if (index < 0)
+		return index;
+
+	return fwnode_irq_get(fwnode, index);
+}
+EXPORT_SYMBOL(fwnode_irq_get_byname);
+
+/**
  * fwnode_graph_get_next_endpoint - Get next endpoint firmware node
  * @fwnode: Pointer to the parent firmware node
  * @prev: Previous endpoint node or %NULL to get the first
@@ -1033,25 +1107,31 @@
 fwnode_graph_get_next_endpoint(const struct fwnode_handle *fwnode,
 			       struct fwnode_handle *prev)
 {
+	struct fwnode_handle *ep, *port_parent = NULL;
 	const struct fwnode_handle *parent;
-	struct fwnode_handle *ep;
 
 	/*
 	 * If this function is in a loop and the previous iteration returned
 	 * an endpoint from fwnode->secondary, then we need to use the secondary
 	 * as parent rather than @fwnode.
 	 */
-	if (prev)
-		parent = fwnode_graph_get_port_parent(prev);
-	else
+	if (prev) {
+		port_parent = fwnode_graph_get_port_parent(prev);
+		parent = port_parent;
+	} else {
 		parent = fwnode;
+	}
+	if (IS_ERR_OR_NULL(parent))
+		return NULL;
 
 	ep = fwnode_call_ptr_op(parent, graph_get_next_endpoint, prev);
+	if (ep)
+		goto out_put_port_parent;
 
-	if (IS_ERR_OR_NULL(ep) &&
-	    !IS_ERR_OR_NULL(parent) && !IS_ERR_OR_NULL(parent->secondary))
-		ep = fwnode_graph_get_next_endpoint(parent->secondary, NULL);
+	ep = fwnode_graph_get_next_endpoint(parent->secondary, NULL);
 
+out_put_port_parent:
+	fwnode_handle_put(port_parent);
 	return ep;
 }
 EXPORT_SYMBOL_GPL(fwnode_graph_get_next_endpoint);
@@ -1253,7 +1333,7 @@
 }
 EXPORT_SYMBOL(fwnode_graph_parse_endpoint);
 
-const void *device_get_match_data(struct device *dev)
+const void *device_get_match_data(const struct device *dev)
 {
 	return fwnode_call_ptr_op(dev_fwnode(dev), device_get_match_data, dev);
 }
@@ -1269,8 +1349,10 @@
 
 	fwnode_graph_for_each_endpoint(fwnode, ep) {
 		node = fwnode_graph_get_remote_port_parent(ep);
-		if (!fwnode_device_is_available(node))
+		if (!fwnode_device_is_available(node)) {
+			fwnode_handle_put(node);
 			continue;
+		}
 
 		ret = match(node, con_id, data);
 		fwnode_handle_put(node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/internal.h
@@ -108,6 +108,10 @@
 	int (*reg_write)(void *context, unsigned int reg, unsigned int val);
 	int (*reg_update_bits)(void *context, unsigned int reg,
 			       unsigned int mask, unsigned int val);
+	/* Bulk read/write */
+	int (*read)(void *context, const void *reg_buf, size_t reg_size,
+		    void *val_buf, size_t val_size);
+	int (*write)(void *context, const void *data, size_t count);
 
 	bool defer_caching;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/regcache-rbtree.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/regcache-rbtree.c
@@ -277,7 +277,7 @@
 
 	blk = krealloc(rbnode->block,
 		       blklen * map->cache_word_size,
-		       GFP_KERNEL);
+		       map->alloc_flags);
 	if (!blk)
 		return -ENOMEM;
 
@@ -286,7 +286,7 @@
 	if (BITS_TO_LONGS(blklen) > BITS_TO_LONGS(rbnode->blklen)) {
 		present = krealloc(rbnode->cache_present,
 				   BITS_TO_LONGS(blklen) * sizeof(*present),
-				   GFP_KERNEL);
+				   map->alloc_flags);
 		if (!present)
 			return -ENOMEM;
 
@@ -320,7 +320,7 @@
 	const struct regmap_range *range;
 	int i;
 
-	rbnode = kzalloc(sizeof(*rbnode), GFP_KERNEL);
+	rbnode = kzalloc(sizeof(*rbnode), map->alloc_flags);
 	if (!rbnode)
 		return NULL;
 
@@ -346,13 +346,13 @@
 	}
 
 	rbnode->block = kmalloc_array(rbnode->blklen, map->cache_word_size,
-				      GFP_KERNEL);
+				      map->alloc_flags);
 	if (!rbnode->block)
 		goto err_free;
 
 	rbnode->cache_present = kcalloc(BITS_TO_LONGS(rbnode->blklen),
 					sizeof(*rbnode->cache_present),
-					GFP_KERNEL);
+					map->alloc_flags);
 	if (!rbnode->cache_present)
 		goto err_free_block;
 
@@ -453,7 +453,8 @@
 		if (!rbnode)
 			return -ENOMEM;
 		regcache_rbtree_set_register(map, rbnode,
-					     reg - rbnode->base_reg, value);
+					     (reg - rbnode->base_reg) / map->reg_stride,
+					     value);
 		regcache_rbtree_insert(map, &rbtree_ctx->root, rbnode);
 		rbtree_ctx->cached_rbnode = rbnode;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/regcache.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/regcache.c
@@ -325,6 +325,11 @@
 	return 0;
 }
 
+static int rbtree_all(const void *key, const struct rb_node *node)
+{
+	return 0;
+}
+
 /**
  * regcache_sync - Sync the register cache with the hardware.
  *
@@ -342,6 +347,10 @@
 	unsigned int i;
 	const char *name;
 	bool bypass;
+	struct rb_node *node;
+
+	if (WARN_ON(map->cache_type == REGCACHE_NONE))
+		return -EINVAL;
 
 	BUG_ON(!map->cache_ops);
 
@@ -383,6 +392,29 @@
 	map->async = false;
 	map->cache_bypass = bypass;
 	map->no_sync_defaults = false;
+
+	/*
+	 * If we did any paging with cache bypassed and a cached
+	 * paging register then the register and cache state might
+	 * have gone out of sync, force writes of all the paging
+	 * registers.
+	 */
+	rb_for_each(node, 0, &map->range_tree, rbtree_all) {
+		struct regmap_range_node *this =
+			rb_entry(node, struct regmap_range_node, node);
+
+		/* If there's nothing in the cache there's nothing to sync */
+		if (regcache_read(map, this->selector_reg, &i) != 0)
+			continue;
+
+		ret = _regmap_write(map, this->selector_reg, i);
+		if (ret != 0) {
+			dev_err(map->dev, "Failed to write %x = %x: %d\n",
+				this->selector_reg, i, ret);
+			break;
+		}
+	}
+
 	map->unlock(map->lock_arg);
 
 	regmap_async_complete(map);
@@ -412,6 +444,9 @@
 	const char *name;
 	bool bypass;
 
+	if (WARN_ON(map->cache_type == REGCACHE_NONE))
+		return -EINVAL;
+
 	BUG_ON(!map->cache_ops);
 
 	map->lock(map->lock_arg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/regmap-debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/regmap-debugfs.c
@@ -48,7 +48,7 @@
 		name = map->dev->driver->name;
 
 	ret = snprintf(buf, PAGE_SIZE, "%s\n", name);
-	if (ret < 0) {
+	if (ret >= PAGE_SIZE) {
 		kfree(buf);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/regmap-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/regmap-i2c.c
@@ -242,8 +242,8 @@
 static const struct regmap_bus regmap_i2c_smbus_i2c_block = {
 	.write = regmap_i2c_smbus_i2c_write,
 	.read = regmap_i2c_smbus_i2c_read,
-	.max_raw_read = I2C_SMBUS_BLOCK_MAX,
-	.max_raw_write = I2C_SMBUS_BLOCK_MAX,
+	.max_raw_read = I2C_SMBUS_BLOCK_MAX - 1,
+	.max_raw_write = I2C_SMBUS_BLOCK_MAX - 1,
 };
 
 static int regmap_i2c_smbus_i2c_write_reg16(void *context, const void *data,
@@ -299,8 +299,8 @@
 static const struct regmap_bus regmap_i2c_smbus_i2c_block_reg16 = {
 	.write = regmap_i2c_smbus_i2c_write_reg16,
 	.read = regmap_i2c_smbus_i2c_read_reg16,
-	.max_raw_read = I2C_SMBUS_BLOCK_MAX,
-	.max_raw_write = I2C_SMBUS_BLOCK_MAX,
+	.max_raw_read = I2C_SMBUS_BLOCK_MAX - 2,
+	.max_raw_write = I2C_SMBUS_BLOCK_MAX - 2,
 };
 
 static const struct regmap_bus *regmap_get_i2c_bus(struct i2c_client *i2c,
@@ -350,7 +350,8 @@
 
 		if (quirks->max_write_len &&
 		    (bus->max_raw_write == 0 || bus->max_raw_write > quirks->max_write_len))
-			max_write = quirks->max_write_len;
+			max_write = quirks->max_write_len -
+				(config->reg_bits + config->pad_bits) / BITS_PER_BYTE;
 
 		if (max_read || max_write) {
 			ret_bus = kmemdup(bus, sizeof(*bus), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/regmap-irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/regmap-irq.c
@@ -189,11 +189,9 @@
 				ret = regmap_write(map, reg, d->mask_buf[i]);
 			if (d->chip->clear_ack) {
 				if (d->chip->ack_invert && !ret)
-					ret = regmap_write(map, reg,
-							   d->mask_buf[i]);
+					ret = regmap_write(map, reg, UINT_MAX);
 				else if (!ret)
-					ret = regmap_write(map, reg,
-							   ~d->mask_buf[i]);
+					ret = regmap_write(map, reg, 0);
 			}
 			if (ret != 0)
 				dev_err(d->map->dev, "Failed to ack 0x%x: %d\n",
@@ -254,6 +252,7 @@
 	struct regmap_irq_chip_data *d = irq_data_get_irq_chip_data(data);
 	struct regmap *map = d->map;
 	const struct regmap_irq *irq_data = irq_to_regmap_irq(d, data->hwirq);
+	unsigned int reg = irq_data->reg_offset / map->reg_stride;
 	unsigned int mask, type;
 
 	type = irq_data->type.type_falling_val | irq_data->type.type_rising_val;
@@ -270,14 +269,14 @@
 	 * at the corresponding offset in regmap_irq_set_type().
 	 */
 	if (d->chip->type_in_mask && type)
-		mask = d->type_buf[irq_data->reg_offset / map->reg_stride];
+		mask = d->type_buf[reg] & irq_data->mask;
 	else
 		mask = irq_data->mask;
 
 	if (d->chip->clear_on_unmask)
 		d->clear_status = true;
 
-	d->mask_buf[irq_data->reg_offset / map->reg_stride] &= ~mask;
+	d->mask_buf[reg] &= ~mask;
 }
 
 static void regmap_irq_disable(struct irq_data *data)
@@ -388,6 +387,7 @@
 		subreg = &chip->sub_reg_offsets[b];
 		for (i = 0; i < subreg->num_regs; i++) {
 			unsigned int offset = subreg->offset[i];
+			unsigned int index = offset / map->reg_stride;
 
 			if (chip->not_fixed_stride)
 				ret = regmap_read(map,
@@ -396,7 +396,7 @@
 			else
 				ret = regmap_read(map,
 						chip->status_base + offset,
-						&data->status_buf[offset]);
+						&data->status_buf[index]);
 
 			if (ret)
 				break;
@@ -556,11 +556,9 @@
 						data->status_buf[i]);
 			if (chip->clear_ack) {
 				if (chip->ack_invert && !ret)
-					ret = regmap_write(map, reg,
-							data->status_buf[i]);
+					ret = regmap_write(map, reg, UINT_MAX);
 				else if (!ret)
-					ret = regmap_write(map, reg,
-							~data->status_buf[i]);
+					ret = regmap_write(map, reg, 0);
 			}
 			if (ret != 0)
 				dev_err(map->dev, "Failed to ack 0x%x: %d\n",
@@ -589,12 +587,16 @@
 		return IRQ_NONE;
 }
 
+static struct lock_class_key regmap_irq_lock_class;
+static struct lock_class_key regmap_irq_request_class;
+
 static int regmap_irq_map(struct irq_domain *h, unsigned int virq,
 			  irq_hw_number_t hw)
 {
 	struct regmap_irq_chip_data *data = h->host_data;
 
 	irq_set_chip_data(virq, data);
+	irq_set_lockdep_class(virq, &regmap_irq_lock_class, &regmap_irq_request_class);
 	irq_set_chip(virq, &data->irq_chip);
 	irq_set_nested_thread(virq, 1);
 	irq_set_parent(virq, data->irq);
@@ -817,13 +819,9 @@
 					d->status_buf[i] & d->mask_buf[i]);
 			if (chip->clear_ack) {
 				if (chip->ack_invert && !ret)
-					ret = regmap_write(map, reg,
-						(d->status_buf[i] &
-						 d->mask_buf[i]));
+					ret = regmap_write(map, reg, UINT_MAX);
 				else if (!ret)
-					ret = regmap_write(map, reg,
-						~(d->status_buf[i] &
-						  d->mask_buf[i]));
+					ret = regmap_write(map, reg, 0);
 			}
 			if (ret != 0) {
 				dev_err(map->dev, "Failed to ack 0x%x: %d\n",
@@ -906,6 +904,7 @@
 	kfree(d->wake_buf);
 	kfree(d->mask_buf_def);
 	kfree(d->mask_buf);
+	kfree(d->main_status_buf);
 	kfree(d->status_buf);
 	kfree(d->status_reg_buf);
 	if (d->virt_buf) {
@@ -981,6 +980,7 @@
 	kfree(d->wake_buf);
 	kfree(d->mask_buf_def);
 	kfree(d->mask_buf);
+	kfree(d->main_status_buf);
 	kfree(d->status_reg_buf);
 	kfree(d->status_buf);
 	kfree(d);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/regmap/regmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/regmap/regmap.c
@@ -647,6 +647,7 @@
 	if (ret)
 		return ret;
 
+	regmap_debugfs_exit(map);
 	regmap_debugfs_init(map);
 
 	/* Add a devres resource for dev_get_regmap() */
@@ -662,6 +663,17 @@
 }
 EXPORT_SYMBOL_GPL(regmap_attach_dev);
 
+static int dev_get_regmap_match(struct device *dev, void *res, void *data);
+
+static int regmap_detach_dev(struct device *dev, struct regmap *map)
+{
+	if (!dev)
+		return 0;
+
+	return devres_release(dev, dev_get_regmap_release,
+			      dev_get_regmap_match, (void *)map->name);
+}
+
 static enum regmap_endian regmap_get_reg_endian(const struct regmap_bus *bus,
 					const struct regmap_config *config)
 {
@@ -834,12 +846,15 @@
 		map->reg_stride_order = ilog2(map->reg_stride);
 	else
 		map->reg_stride_order = -1;
-	map->use_single_read = config->use_single_read || !bus || !bus->read;
-	map->use_single_write = config->use_single_write || !bus || !bus->write;
-	map->can_multi_write = config->can_multi_write && bus && bus->write;
+	map->use_single_read = config->use_single_read || !(config->read || (bus && bus->read));
+	map->use_single_write = config->use_single_write || !(config->write || (bus && bus->write));
+	map->can_multi_write = config->can_multi_write && (config->write || (bus && bus->write));
 	if (bus) {
 		map->max_raw_read = bus->max_raw_read;
 		map->max_raw_write = bus->max_raw_write;
+	} else if (config->max_raw_read && config->max_raw_write) {
+		map->max_raw_read = config->max_raw_read;
+		map->max_raw_write = config->max_raw_write;
 	}
 	map->dev = dev;
 	map->bus = bus;
@@ -873,9 +888,19 @@
 		map->read_flag_mask = bus->read_flag_mask;
 	}
 
-	if (!bus) {
+	if (config && config->read && config->write) {
+		map->reg_read  = _regmap_bus_read;
+
+		/* Bulk read/write */
+		map->read = config->read;
+		map->write = config->write;
+
+		reg_endian = REGMAP_ENDIAN_NATIVE;
+		val_endian = REGMAP_ENDIAN_NATIVE;
+	} else if (!bus) {
 		map->reg_read  = config->reg_read;
 		map->reg_write = config->reg_write;
+		map->reg_update_bits = config->reg_update_bits;
 
 		map->defer_caching = false;
 		goto skip_format_initialization;
@@ -889,10 +914,13 @@
 	} else {
 		map->reg_read  = _regmap_bus_read;
 		map->reg_update_bits = bus->reg_update_bits;
-	}
+		/* Bulk read/write */
+		map->read = bus->read;
+		map->write = bus->write;
 
-	reg_endian = regmap_get_reg_endian(bus, config);
-	val_endian = regmap_get_val_endian(dev, bus, config);
+		reg_endian = regmap_get_reg_endian(bus, config);
+		val_endian = regmap_get_val_endian(dev, bus, config);
+	}
 
 	switch (config->reg_bits + map->reg_shift) {
 	case 2:
@@ -1125,13 +1153,13 @@
 
 		/* Sanity check */
 		if (range_cfg->range_max < range_cfg->range_min) {
-			dev_err(map->dev, "Invalid range %d: %d < %d\n", i,
+			dev_err(map->dev, "Invalid range %d: %u < %u\n", i,
 				range_cfg->range_max, range_cfg->range_min);
 			goto err_range;
 		}
 
 		if (range_cfg->range_max > map->max_register) {
-			dev_err(map->dev, "Invalid range %d: %d > %d\n", i,
+			dev_err(map->dev, "Invalid range %d: %u > %u\n", i,
 				range_cfg->range_max, map->max_register);
 			goto err_range;
 		}
@@ -1514,6 +1542,7 @@
 {
 	struct regmap_async *async;
 
+	regmap_detach_dev(map->dev, map);
 	regcache_exit(map);
 	regmap_debugfs_exit(map);
 	regmap_range_exit(map);
@@ -1550,7 +1579,7 @@
 
 	/* If the user didn't specify a name match any */
 	if (data)
-		return !strcmp((*r)->name, data);
+		return (*r)->name && !strcmp((*r)->name, data);
 	else
 		return 1;
 }
@@ -1666,8 +1695,6 @@
 	size_t len;
 	int i;
 
-	WARN_ON(!map->bus);
-
 	/* Check for unwritable or noinc registers in range
 	 * before we start
 	 */
@@ -1682,17 +1709,19 @@
 	}
 
 	if (!map->cache_bypass && map->format.parse_val) {
-		unsigned int ival;
+		unsigned int ival, offset;
 		int val_bytes = map->format.val_bytes;
-		for (i = 0; i < val_len / val_bytes; i++) {
-			ival = map->format.parse_val(val + (i * val_bytes));
-			ret = regcache_write(map,
-					     reg + regmap_get_offset(map, i),
-					     ival);
+
+		/* Cache the last written value for noinc writes */
+		i = noinc ? val_len - val_bytes : 0;
+		for (; i < val_len; i += val_bytes) {
+			ival = map->format.parse_val(val + i);
+			offset = noinc ? 0 : regmap_get_offset(map, i / val_bytes);
+			ret = regcache_write(map, reg + offset, ival);
 			if (ret) {
 				dev_err(map->dev,
 					"Error in caching of register: %x ret: %d\n",
-					reg + regmap_get_offset(map, i), ret);
+					reg + offset, ret);
 				return ret;
 			}
 		}
@@ -1747,7 +1776,7 @@
 		val = work_val;
 	}
 
-	if (map->async && map->bus->async_write) {
+	if (map->async && map->bus && map->bus->async_write) {
 		struct regmap_async *async;
 
 		trace_regmap_async_write_start(map, reg, val_len);
@@ -1815,11 +1844,11 @@
 	 * write.
 	 */
 	if (val == work_val)
-		ret = map->bus->write(map->bus_context, map->work_buf,
-				      map->format.reg_bytes +
-				      map->format.pad_bytes +
-				      val_len);
-	else if (map->bus->gather_write)
+		ret = map->write(map->bus_context, map->work_buf,
+				 map->format.reg_bytes +
+				 map->format.pad_bytes +
+				 val_len);
+	else if (map->bus && map->bus->gather_write)
 		ret = map->bus->gather_write(map->bus_context, map->work_buf,
 					     map->format.reg_bytes +
 					     map->format.pad_bytes,
@@ -1837,7 +1866,7 @@
 		memcpy(buf, map->work_buf, map->format.reg_bytes);
 		memcpy(buf + map->format.reg_bytes + map->format.pad_bytes,
 		       val, val_len);
-		ret = map->bus->write(map->bus_context, buf, len);
+		ret = map->write(map->bus_context, buf, len);
 
 		kfree(buf);
 	} else if (ret != 0 && !map->cache_bypass && map->format.parse_val) {
@@ -1894,7 +1923,7 @@
 	struct regmap_range_node *range;
 	struct regmap *map = context;
 
-	WARN_ON(!map->bus || !map->format.format_write);
+	WARN_ON(!map->format.format_write);
 
 	range = _regmap_range_lookup(map, reg);
 	if (range) {
@@ -1907,8 +1936,7 @@
 
 	trace_regmap_hw_write_start(map, reg, 1);
 
-	ret = map->bus->write(map->bus_context, map->work_buf,
-			      map->format.buf_size);
+	ret = map->write(map->bus_context, map->work_buf, map->format.buf_size);
 
 	trace_regmap_hw_write_done(map, reg, 1);
 
@@ -1928,7 +1956,7 @@
 {
 	struct regmap *map = context;
 
-	WARN_ON(!map->bus || !map->format.format_val);
+	WARN_ON(!map->format.format_val);
 
 	map->format.format_val(map->work_buf + map->format.reg_bytes
 			       + map->format.pad_bytes, val, 0);
@@ -1942,7 +1970,7 @@
 
 static inline void *_regmap_map_get_context(struct regmap *map)
 {
-	return (map->bus) ? map : map->bus_context;
+	return (map->bus || (!map->bus && map->read)) ? map : map->bus_context;
 }
 
 int _regmap_write(struct regmap *map, unsigned int reg,
@@ -2352,7 +2380,7 @@
 	u8 = buf;
 	*u8 |= map->write_flag_mask;
 
-	ret = map->bus->write(map->bus_context, buf, len);
+	ret = map->write(map->bus_context, buf, len);
 
 	kfree(buf);
 
@@ -2658,9 +2686,7 @@
 	struct regmap_range_node *range;
 	int ret;
 
-	WARN_ON(!map->bus);
-
-	if (!map->bus || !map->bus->read)
+	if (!map->read)
 		return -EINVAL;
 
 	range = _regmap_range_lookup(map, reg);
@@ -2676,9 +2702,9 @@
 				      map->read_flag_mask);
 	trace_regmap_hw_read_start(map, reg, val_len / map->format.val_bytes);
 
-	ret = map->bus->read(map->bus_context, map->work_buf,
-			     map->format.reg_bytes + map->format.pad_bytes,
-			     val, val_len);
+	ret = map->read(map->bus_context, map->work_buf,
+			map->format.reg_bytes + map->format.pad_bytes,
+			val, val_len);
 
 	trace_regmap_hw_read_done(map, reg, val_len / map->format.val_bytes);
 
@@ -2789,8 +2815,6 @@
 	unsigned int v;
 	int ret, i;
 
-	if (!map->bus)
-		return -EINVAL;
 	if (val_len % map->format.val_bytes)
 		return -EINVAL;
 	if (!IS_ALIGNED(reg, map->reg_stride))
@@ -2805,7 +2829,7 @@
 		size_t chunk_count, chunk_bytes;
 		size_t chunk_regs = val_count;
 
-		if (!map->bus->read) {
+		if (!map->read) {
 			ret = -ENOTSUPP;
 			goto out;
 		}
@@ -2865,7 +2889,7 @@
  * @val: Pointer to data buffer
  * @val_len: Length of output buffer in bytes.
  *
- * The regmap API usually assumes that bulk bus read operations will read a
+ * The regmap API usually assumes that bulk read operations will read a
  * range of registers. Some devices have certain registers for which a read
  * operation read will read from an internal FIFO.
  *
@@ -2883,10 +2907,6 @@
 	size_t read_len;
 	int ret;
 
-	if (!map->bus)
-		return -EINVAL;
-	if (!map->bus->read)
-		return -ENOTSUPP;
 	if (val_len % map->format.val_bytes)
 		return -EINVAL;
 	if (!IS_ALIGNED(reg, map->reg_stride))
@@ -3000,7 +3020,7 @@
 	if (val_count == 0)
 		return -EINVAL;
 
-	if (map->bus && map->format.parse_inplace && (vol || map->cache_type == REGCACHE_NONE)) {
+	if (map->format.parse_inplace && (vol || map->cache_type == REGCACHE_NONE)) {
 		ret = regmap_raw_read(map, reg, val, val_bytes * val_count);
 		if (ret != 0)
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/swnode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/swnode.c
@@ -535,7 +535,7 @@
 		return -ENOENT;
 
 	if (nargs_prop) {
-		error = property_entry_read_int_array(swnode->node->properties,
+		error = property_entry_read_int_array(ref->node->properties,
 						      nargs_prop, sizeof(u32),
 						      &nargs_prop_val, 1);
 		if (error)
@@ -547,6 +547,9 @@
 	if (nargs > NR_FWNODE_REFERENCE_ARGS)
 		return -EINVAL;
 
+	if (!args)
+		return 0;
+
 	args->fwnode = software_node_get(refnode);
 	args->nargs = nargs;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/test/test_async_driver_probe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/test/test_async_driver_probe.c
@@ -84,7 +84,7 @@
 
 	pdev = platform_device_alloc(name, id);
 	if (!pdev)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	if (nid != NUMA_NO_NODE)
 		set_dev_node(&pdev->dev, nid);
@@ -146,7 +146,7 @@
 	calltime = ktime_get();
 	for_each_online_cpu(cpu) {
 		nid = cpu_to_node(cpu);
-		pdev = &sync_dev[sync_id];
+		pdev = &async_dev[async_id];
 
 		*pdev = test_platform_device_register_node("test_async_driver",
 							   async_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/topology.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/topology.c
@@ -27,9 +27,17 @@
 			   loff_t off, size_t count)				\
 {										\
 	struct device *dev = kobj_to_dev(kobj);                                 \
+	cpumask_var_t mask;							\
+	ssize_t n;								\
 										\
-	return cpumap_print_bitmask_to_buf(buf, topology_##mask(dev->id),	\
-					   off, count);                         \
+	if (!alloc_cpumask_var(&mask, GFP_KERNEL))				\
+		return -ENOMEM;							\
+										\
+	cpumask_copy(mask, topology_##mask(dev->id));				\
+	n = cpumap_print_bitmask_to_buf(buf, mask, off, count);			\
+	free_cpumask_var(mask);							\
+										\
+	return n;								\
 }										\
 										\
 static ssize_t name##_list_read(struct file *file, struct kobject *kobj,	\
@@ -37,9 +45,17 @@
 				loff_t off, size_t count)			\
 {										\
 	struct device *dev = kobj_to_dev(kobj);					\
+	cpumask_var_t mask;							\
+	ssize_t n;								\
+										\
+	if (!alloc_cpumask_var(&mask, GFP_KERNEL))				\
+		return -ENOMEM;							\
+										\
+	cpumask_copy(mask, topology_##mask(dev->id));				\
+	n = cpumap_print_list_to_buf(buf, mask, off, count);			\
+	free_cpumask_var(mask);							\
 										\
-	return cpumap_print_list_to_buf(buf, topology_##mask(dev->id),		\
-					off, count);				\
+	return n;								\
 }
 
 define_id_show_func(physical_package_id);
@@ -52,39 +68,39 @@
 static DEVICE_ATTR_RO(core_id);
 
 define_siblings_read_func(thread_siblings, sibling_cpumask);
-static BIN_ATTR_RO(thread_siblings, 0);
-static BIN_ATTR_RO(thread_siblings_list, 0);
+static BIN_ATTR_RO(thread_siblings, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(thread_siblings_list, CPULIST_FILE_MAX_BYTES);
 
 define_siblings_read_func(core_cpus, sibling_cpumask);
-static BIN_ATTR_RO(core_cpus, 0);
-static BIN_ATTR_RO(core_cpus_list, 0);
+static BIN_ATTR_RO(core_cpus, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(core_cpus_list, CPULIST_FILE_MAX_BYTES);
 
 define_siblings_read_func(core_siblings, core_cpumask);
-static BIN_ATTR_RO(core_siblings, 0);
-static BIN_ATTR_RO(core_siblings_list, 0);
+static BIN_ATTR_RO(core_siblings, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(core_siblings_list, CPULIST_FILE_MAX_BYTES);
 
 define_siblings_read_func(die_cpus, die_cpumask);
-static BIN_ATTR_RO(die_cpus, 0);
-static BIN_ATTR_RO(die_cpus_list, 0);
+static BIN_ATTR_RO(die_cpus, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(die_cpus_list, CPULIST_FILE_MAX_BYTES);
 
 define_siblings_read_func(package_cpus, core_cpumask);
-static BIN_ATTR_RO(package_cpus, 0);
-static BIN_ATTR_RO(package_cpus_list, 0);
+static BIN_ATTR_RO(package_cpus, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(package_cpus_list, CPULIST_FILE_MAX_BYTES);
 
 #ifdef CONFIG_SCHED_BOOK
 define_id_show_func(book_id);
 static DEVICE_ATTR_RO(book_id);
 define_siblings_read_func(book_siblings, book_cpumask);
-static BIN_ATTR_RO(book_siblings, 0);
-static BIN_ATTR_RO(book_siblings_list, 0);
+static BIN_ATTR_RO(book_siblings, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(book_siblings_list, CPULIST_FILE_MAX_BYTES);
 #endif
 
 #ifdef CONFIG_SCHED_DRAWER
 define_id_show_func(drawer_id);
 static DEVICE_ATTR_RO(drawer_id);
 define_siblings_read_func(drawer_siblings, drawer_cpumask);
-static BIN_ATTR_RO(drawer_siblings, 0);
-static BIN_ATTR_RO(drawer_siblings_list, 0);
+static BIN_ATTR_RO(drawer_siblings, CPUMAP_FILE_MAX_BYTES);
+static BIN_ATTR_RO(drawer_siblings_list, CPULIST_FILE_MAX_BYTES);
 #endif
 
 static struct bin_attribute *bin_attrs[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/base/transport_class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/base/transport_class.c
@@ -155,12 +155,27 @@
 				      struct device *dev,
 				      struct device *classdev)
 {
+	struct transport_class *tclass = class_to_transport_class(cont->class);
 	int error = attribute_container_add_class_device(classdev);
 	struct transport_container *tcont = 
 		attribute_container_to_transport_container(cont);
 
-	if (!error && tcont->statistics)
+	if (error)
+		goto err_remove;
+
+	if (tcont->statistics) {
 		error = sysfs_create_group(&classdev->kobj, tcont->statistics);
+		if (error)
+			goto err_del;
+	}
+
+	return 0;
+
+err_del:
+	attribute_container_class_device_del(classdev);
+err_remove:
+	if (tclass->remove)
+		tclass->remove(tcont, dev, classdev);
 
 	return error;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/Kconfig
@@ -33,6 +33,22 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called floppy.
 
+config BLK_DEV_FD_RAWCMD
+	bool "Support for raw floppy disk commands (DEPRECATED)"
+	depends on BLK_DEV_FD
+	help
+	  If you want to use actual physical floppies and expect to do
+	  special low-level hardware accesses to them (access and use
+	  non-standard formats, for example), then enable this.
+
+	  Note that the code enabled by this option is rarely used and
+	  might be unstable or insecure, and distros should not enable it.
+
+	  Note: FDRAWCMD is deprecated and will be removed from the kernel
+	  in the near future.
+
+	  If unsure, say N.
+
 config AMIGA_FLOPPY
 	tristate "Amiga floppy support"
 	depends on AMIGA
@@ -255,15 +271,6 @@
 
 	  If unsure, say N.
 
-config BLK_DEV_SX8
-	tristate "Promise SATA SX8 support"
-	depends on PCI
-	help
-	  Saying Y or M here will enable support for the 
-	  Promise SATA SX8 controllers.
-
-	  Use devices /dev/sx8/$N and /dev/sx8/$Np$M.
-
 config BLK_DEV_RAM
 	tristate "RAM block device support"
 	help
@@ -394,6 +401,7 @@
 config VIRTIO_BLK
 	tristate "Virtio block driver"
 	depends on VIRTIO
+	select SG_POOL
 	help
 	  This is the virtual block driver for virtio.  It can be used with
           QEMU based VMMs (like KVM or Xen).  Say Y or M.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/Makefile
@@ -27,8 +27,6 @@
 obj-$(CONFIG_BLK_DEV_CRYPTOLOOP) += cryptoloop.o
 obj-$(CONFIG_VIRTIO_BLK)	+= virtio_blk.o
 
-obj-$(CONFIG_BLK_DEV_SX8)	+= sx8.o
-
 obj-$(CONFIG_XEN_BLKDEV_FRONTEND)	+= xen-blkfront.o
 obj-$(CONFIG_XEN_BLKDEV_BACKEND)	+= xen-blkback/
 obj-$(CONFIG_BLK_DEV_DRBD)     += drbd/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/amiflop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/amiflop.c
@@ -61,6 +61,7 @@
 #include <linux/hdreg.h>
 #include <linux/delay.h>
 #include <linux/init.h>
+#include <linux/major.h>
 #include <linux/mutex.h>
 #include <linux/fs.h>
 #include <linux/blk-mq.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/aoe/aoecmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/aoe/aoecmd.c
@@ -362,6 +362,7 @@
 	}
 
 	ah->cmdstat = ATA_CMD_PIO_READ | writebit | extbit;
+	dev_hold(t->ifp->nd);
 	skb->dev = t->ifp->nd;
 }
 
@@ -402,6 +403,8 @@
 		__skb_queue_head_init(&queue);
 		__skb_queue_tail(&queue, skb);
 		aoenet_xmit(&queue);
+	} else {
+		dev_put(f->t->ifp->nd);
 	}
 	return 1;
 }
@@ -420,13 +423,16 @@
 	rcu_read_lock();
 	for_each_netdev_rcu(&init_net, ifp) {
 		dev_hold(ifp);
-		if (!is_aoe_netif(ifp))
-			goto cont;
+		if (!is_aoe_netif(ifp)) {
+			dev_put(ifp);
+			continue;
+		}
 
 		skb = new_skb(sizeof *h + sizeof *ch);
 		if (skb == NULL) {
 			printk(KERN_INFO "aoe: skb alloc failure\n");
-			goto cont;
+			dev_put(ifp);
+			continue;
 		}
 		skb_put(skb, sizeof *h + sizeof *ch);
 		skb->dev = ifp;
@@ -441,9 +447,6 @@
 		h->major = cpu_to_be16(aoemajor);
 		h->minor = aoeminor;
 		h->cmd = AOECMD_CFG;
-
-cont:
-		dev_put(ifp);
 	}
 	rcu_read_unlock();
 }
@@ -484,10 +487,13 @@
 	memcpy(h->dst, t->addr, sizeof h->dst);
 	memcpy(h->src, t->ifp->nd->dev_addr, sizeof h->src);
 
+	dev_hold(t->ifp->nd);
 	skb->dev = t->ifp->nd;
 	skb = skb_clone(skb, GFP_ATOMIC);
-	if (skb == NULL)
+	if (skb == NULL) {
+		dev_put(t->ifp->nd);
 		return;
+	}
 	f->sent = ktime_get();
 	__skb_queue_head_init(&queue);
 	__skb_queue_tail(&queue, skb);
@@ -618,6 +624,8 @@
 		__skb_queue_head_init(&queue);
 		__skb_queue_tail(&queue, skb);
 		aoenet_xmit(&queue);
+	} else {
+		dev_put(f->t->ifp->nd);
 	}
 }
 
@@ -1396,6 +1404,7 @@
 	ah->cmdstat = ATA_CMD_ID_ATA;
 	ah->lba3 = 0xa0;
 
+	dev_hold(t->ifp->nd);
 	skb->dev = t->ifp->nd;
 
 	d->rttavg = RTTAVG_INIT;
@@ -1405,6 +1414,8 @@
 	skb = skb_clone(skb, GFP_ATOMIC);
 	if (skb)
 		f->sent = ktime_get();
+	else
+		dev_put(t->ifp->nd);
 
 	return skb;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/aoe/aoenet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/aoe/aoenet.c
@@ -64,6 +64,7 @@
 			pr_warn("aoe: packet could not be sent on %s.  %s\n",
 				ifp ? ifp->name : "netif",
 				"consider increasing tx_queue_len");
+		dev_put(ifp);
 		spin_lock_irq(&txlock);
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/ataflop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/ataflop.c
@@ -68,6 +68,7 @@
 #include <linux/delay.h>
 #include <linux/init.h>
 #include <linux/blk-mq.h>
+#include <linux/major.h>
 #include <linux/mutex.h>
 #include <linux/completion.h>
 #include <linux/wait.h>
@@ -298,6 +299,7 @@
 				   disk change detection) */
 	int flags;		/* flags */
 	struct gendisk *disk[NUM_DISK_MINORS];
+	bool registered[NUM_DISK_MINORS];
 	int ref;
 	int type;
 	struct blk_mq_tag_set tag_set;
@@ -456,10 +458,20 @@
 	
 static void fd_end_request_cur(blk_status_t err)
 {
+	DPRINT(("fd_end_request_cur(), bytes %d of %d\n",
+		blk_rq_cur_bytes(fd_request),
+		blk_rq_bytes(fd_request)));
+
 	if (!blk_update_request(fd_request, err,
 				blk_rq_cur_bytes(fd_request))) {
+		DPRINT(("calling __blk_mq_end_request()\n"));
 		__blk_mq_end_request(fd_request, err);
 		fd_request = NULL;
+	} else {
+		/* requeue rest of request */
+		DPRINT(("calling blk_mq_requeue_request()\n"));
+		blk_mq_requeue_request(fd_request, true);
+		fd_request = NULL;
 	}
 }
 
@@ -653,9 +665,6 @@
 		*p2++ = *p1++;
 }
 
-  
-  
-
 /* General Interrupt Handling */
 
 static void (*FloppyIRQHandler)( int status ) = NULL;
@@ -700,12 +709,21 @@
 	if (fd_request->error_count >= MAX_ERRORS) {
 		printk(KERN_ERR "fd%d: too many errors.\n", SelectedDrive );
 		fd_end_request_cur(BLK_STS_IOERR);
+		finish_fdc();
+		return;
 	}
 	else if (fd_request->error_count == RECALIBRATE_ERRORS) {
 		printk(KERN_WARNING "fd%d: recalibrating\n", SelectedDrive );
 		if (SelectedDrive != -1)
 			SUD.track = -1;
 	}
+	/* need to re-run request to recalibrate */
+	atari_disable_irq( IRQ_MFP_FDC );
+
+	setup_req_params( SelectedDrive );
+	do_fd_action( SelectedDrive );
+
+	atari_enable_irq( IRQ_MFP_FDC );
 }
 
 
@@ -732,8 +750,10 @@
 	if (type) {
 		type--;
 		if (type >= NUM_DISK_MINORS ||
-		    minor2disktype[type].drive_types > DriveType)
+		    minor2disktype[type].drive_types > DriveType) {
+			finish_fdc();
 			return -EINVAL;
+		}
 	}
 
 	q = unit[drive].disk[type]->queue;
@@ -751,6 +771,7 @@
 	}
 
 	if (!UDT || desc->track >= UDT->blocks/UDT->spt/2 || desc->head >= 2) {
+		finish_fdc();
 		ret = -EINVAL;
 		goto out;
 	}
@@ -791,6 +812,7 @@
 
 	wait_for_completion(&format_wait);
 
+	finish_fdc();
 	ret = FormatError ? -EIO : 0;
 out:
 	blk_mq_unquiesce_queue(q);
@@ -825,6 +847,7 @@
 		    else {
 			/* all sectors finished */
 			fd_end_request_cur(BLK_STS_OK);
+			finish_fdc();
 			return;
 		    }
 		}
@@ -1229,6 +1252,7 @@
 	else {
 		/* all sectors finished */
 		fd_end_request_cur(BLK_STS_OK);
+		finish_fdc();
 	}
 	return;
   
@@ -1350,7 +1374,7 @@
 
 static void finish_fdc( void )
 {
-	if (!NeedSeek) {
+	if (!NeedSeek || !stdma_is_locked_by(floppy_irq)) {
 		finish_fdc_done( 0 );
 	}
 	else {
@@ -1385,7 +1409,8 @@
 	start_motor_off_timer();
 
 	local_irq_save(flags);
-	stdma_release();
+	if (stdma_is_locked_by(floppy_irq))
+		stdma_release();
 	local_irq_restore(flags);
 
 	DPRINT(("finish_fdc() finished\n"));
@@ -1475,15 +1500,6 @@
 			ReqTrack, ReqSector, (unsigned long)ReqData ));
 }
 
-static void ataflop_commit_rqs(struct blk_mq_hw_ctx *hctx)
-{
-	spin_lock_irq(&ataflop_lock);
-	atari_disable_irq(IRQ_MFP_FDC);
-	finish_fdc();
-	atari_enable_irq(IRQ_MFP_FDC);
-	spin_unlock_irq(&ataflop_lock);
-}
-
 static blk_status_t ataflop_queue_rq(struct blk_mq_hw_ctx *hctx,
 				     const struct blk_mq_queue_data *bd)
 {
@@ -1491,6 +1507,10 @@
 	int drive = floppy - unit;
 	int type = floppy->type;
 
+	DPRINT(("Queue request: drive %d type %d sectors %d of %d last %d\n",
+		drive, type, blk_rq_cur_sectors(bd->rq),
+		blk_rq_sectors(bd->rq), bd->last));
+
 	spin_lock_irq(&ataflop_lock);
 	if (fd_request) {
 		spin_unlock_irq(&ataflop_lock);
@@ -1511,6 +1531,7 @@
 		/* drive not connected */
 		printk(KERN_ERR "Unknown Device: fd%d\n", drive );
 		fd_end_request_cur(BLK_STS_IOERR);
+		stdma_release();
 		goto out;
 	}
 		
@@ -1527,11 +1548,13 @@
 		if (--type >= NUM_DISK_MINORS) {
 			printk(KERN_WARNING "fd%d: invalid disk format", drive );
 			fd_end_request_cur(BLK_STS_IOERR);
+			stdma_release();
 			goto out;
 		}
 		if (minor2disktype[type].drive_types > DriveType)  {
 			printk(KERN_WARNING "fd%d: unsupported disk format", drive );
 			fd_end_request_cur(BLK_STS_IOERR);
+			stdma_release();
 			goto out;
 		}
 		type = minor2disktype[type].index;
@@ -1550,8 +1573,6 @@
 	setup_req_params( drive );
 	do_fd_action( drive );
 
-	if (bd->last)
-		finish_fdc();
 	atari_enable_irq( IRQ_MFP_FDC );
 
 out:
@@ -1634,6 +1655,7 @@
 		/* what if type > 0 here? Overwrite specified entry ? */
 		if (type) {
 		        /* refuse to re-set a predefined type for now */
+			finish_fdc();
 			return -EINVAL;
 		}
 
@@ -1701,8 +1723,10 @@
 
 		/* sanity check */
 		if (setprm.track != dtp->blocks/dtp->spt/2 ||
-		    setprm.head != 2)
+		    setprm.head != 2) {
+			finish_fdc();
 			return -EINVAL;
+		}
 
 		UDT = dtp;
 		set_capacity(disk, UDT->blocks);
@@ -1962,7 +1986,6 @@
 
 static const struct blk_mq_ops ataflop_mq_ops = {
 	.queue_rq = ataflop_queue_rq,
-	.commit_rqs = ataflop_commit_rqs,
 };
 
 static int ataflop_alloc_disk(unsigned int drive, unsigned int type)
@@ -1986,8 +2009,6 @@
 	return 0;
 }
 
-static DEFINE_MUTEX(ataflop_probe_lock);
-
 static void ataflop_probe(dev_t dev)
 {
 	int drive = MINOR(dev) & 3;
@@ -1998,12 +2019,46 @@
 
 	if (drive >= FD_MAX_UNITS || type >= NUM_DISK_MINORS)
 		return;
-	mutex_lock(&ataflop_probe_lock);
 	if (!unit[drive].disk[type]) {
-		if (ataflop_alloc_disk(drive, type) == 0)
+		if (ataflop_alloc_disk(drive, type) == 0) {
 			add_disk(unit[drive].disk[type]);
+			unit[drive].registered[type] = true;
+		}
+	}
+}
+
+static void atari_floppy_cleanup(void)
+{
+	int i;
+	int type;
+
+	for (i = 0; i < FD_MAX_UNITS; i++) {
+		for (type = 0; type < NUM_DISK_MINORS; type++) {
+			if (!unit[i].disk[type])
+				continue;
+			del_gendisk(unit[i].disk[type]);
+			blk_cleanup_queue(unit[i].disk[type]->queue);
+			put_disk(unit[i].disk[type]);
+		}
+		blk_mq_free_tag_set(&unit[i].tag_set);
+	}
+
+	del_timer_sync(&fd_timer);
+	atari_stram_free(DMABuffer);
+}
+
+static void atari_cleanup_floppy_disk(struct atari_floppy_struct *fs)
+{
+	int type;
+
+	for (type = 0; type < NUM_DISK_MINORS; type++) {
+		if (!fs->disk[type])
+			continue;
+		if (fs->registered[type])
+			del_gendisk(fs->disk[type]);
+		blk_cleanup_disk(fs->disk[type]);
 	}
-	mutex_unlock(&ataflop_probe_lock);
+	blk_mq_free_tag_set(&fs->tag_set);
 }
 
 static int __init atari_floppy_init (void)
@@ -2015,11 +2070,6 @@
 		/* Amiga, Mac, ... don't have Atari-compatible floppy :-) */
 		return -ENODEV;
 
-	mutex_lock(&ataflop_probe_lock);
-	ret = __register_blkdev(FLOPPY_MAJOR, "fd", ataflop_probe);
-	if (ret)
-		goto out_unlock;
-
 	for (i = 0; i < FD_MAX_UNITS; i++) {
 		memset(&unit[i].tag_set, 0, sizeof(unit[i].tag_set));
 		unit[i].tag_set.ops = &ataflop_mq_ops;
@@ -2065,6 +2115,7 @@
 		unit[i].track = -1;
 		unit[i].flags = 0;
 		add_disk(unit[i].disk[0]);
+		unit[i].registered[0] = true;
 	}
 
 	printk(KERN_INFO "Atari floppy driver: max. %cD, %strack buffering\n",
@@ -2072,18 +2123,17 @@
 	       UseTrackbuffer ? "" : "no ");
 	config_types();
 
-	return 0;
+	ret = __register_blkdev(FLOPPY_MAJOR, "fd", ataflop_probe);
+	if (ret) {
+		printk(KERN_ERR "atari_floppy_init: cannot register block device\n");
+		atari_floppy_cleanup();
+	}
+	return ret;
 
 err:
-	while (--i >= 0) {
-		blk_cleanup_queue(unit[i].disk[0]->queue);
-		put_disk(unit[i].disk[0]);
-		blk_mq_free_tag_set(&unit[i].tag_set);
-	}
+	while (--i >= 0)
+		atari_cleanup_floppy_disk(&unit[i]);
 
-	unregister_blkdev(FLOPPY_MAJOR, "fd");
-out_unlock:
-	mutex_unlock(&ataflop_probe_lock);
 	return ret;
 }
 
@@ -2128,22 +2178,8 @@
 
 static void __exit atari_floppy_exit(void)
 {
-	int i, type;
-
-	for (i = 0; i < FD_MAX_UNITS; i++) {
-		for (type = 0; type < NUM_DISK_MINORS; type++) {
-			if (!unit[i].disk[type])
-				continue;
-			del_gendisk(unit[i].disk[type]);
-			blk_cleanup_queue(unit[i].disk[type]->queue);
-			put_disk(unit[i].disk[type]);
-		}
-		blk_mq_free_tag_set(&unit[i].tag_set);
-	}
 	unregister_blkdev(FLOPPY_MAJOR, "fd");
-
-	del_timer_sync(&fd_timer);
-	atari_stram_free( DMABuffer );
+	atari_floppy_cleanup();
 }
 
 module_init(atari_floppy_init)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/brd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/brd.c
@@ -78,11 +78,9 @@
 }
 
 /*
- * Look up and return a brd's page for a given sector.
- * If one does not exist, allocate an empty page, and insert that. Then
- * return it.
+ * Insert a new page for a given sector, if one does not already exist.
  */
-static struct page *brd_insert_page(struct brd_device *brd, sector_t sector)
+static int brd_insert_page(struct brd_device *brd, sector_t sector)
 {
 	pgoff_t idx;
 	struct page *page;
@@ -90,7 +88,7 @@
 
 	page = brd_lookup_page(brd, sector);
 	if (page)
-		return page;
+		return 0;
 
 	/*
 	 * Must use NOIO because we don't want to recurse back into the
@@ -99,11 +97,11 @@
 	gfp_flags = GFP_NOIO | __GFP_ZERO | __GFP_HIGHMEM;
 	page = alloc_page(gfp_flags);
 	if (!page)
-		return NULL;
+		return -ENOMEM;
 
 	if (radix_tree_preload(GFP_NOIO)) {
 		__free_page(page);
-		return NULL;
+		return -ENOMEM;
 	}
 
 	spin_lock(&brd->brd_lock);
@@ -120,8 +118,7 @@
 	spin_unlock(&brd->brd_lock);
 
 	radix_tree_preload_end();
-
-	return page;
+	return 0;
 }
 
 /*
@@ -174,16 +171,17 @@
 {
 	unsigned int offset = (sector & (PAGE_SECTORS-1)) << SECTOR_SHIFT;
 	size_t copy;
+	int ret;
 
 	copy = min_t(size_t, n, PAGE_SIZE - offset);
-	if (!brd_insert_page(brd, sector))
-		return -ENOSPC;
+	ret = brd_insert_page(brd, sector);
+	if (ret)
+		return ret;
 	if (copy < n) {
 		sector += copy >> SECTOR_SHIFT;
-		if (!brd_insert_page(brd, sector))
-			return -ENOSPC;
+		ret = brd_insert_page(brd, sector);
 	}
-	return 0;
+	return ret;
 }
 
 /*
@@ -367,27 +365,47 @@
 static DEFINE_MUTEX(brd_devices_mutex);
 static struct dentry *brd_debugfs_dir;
 
-static int brd_alloc(int i)
+static struct brd_device *brd_find_or_alloc_device(int i)
 {
 	struct brd_device *brd;
-	struct gendisk *disk;
-	char buf[DISK_NAME_LEN];
 
 	mutex_lock(&brd_devices_mutex);
 	list_for_each_entry(brd, &brd_devices, brd_list) {
 		if (brd->brd_number == i) {
 			mutex_unlock(&brd_devices_mutex);
-			return -EEXIST;
+			return ERR_PTR(-EEXIST);
 		}
 	}
+
 	brd = kzalloc(sizeof(*brd), GFP_KERNEL);
 	if (!brd) {
 		mutex_unlock(&brd_devices_mutex);
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
 	}
-	brd->brd_number		= i;
+	brd->brd_number	= i;
 	list_add_tail(&brd->brd_list, &brd_devices);
 	mutex_unlock(&brd_devices_mutex);
+	return brd;
+}
+
+static void brd_free_device(struct brd_device *brd)
+{
+	mutex_lock(&brd_devices_mutex);
+	list_del(&brd->brd_list);
+	mutex_unlock(&brd_devices_mutex);
+	kfree(brd);
+}
+
+static int brd_alloc(int i)
+{
+	struct brd_device *brd;
+	struct gendisk *disk;
+	char buf[DISK_NAME_LEN];
+	int err = -ENOMEM;
+
+	brd = brd_find_or_alloc_device(i);
+	if (IS_ERR(brd))
+		return PTR_ERR(brd);
 
 	spin_lock_init(&brd->brd_lock);
 	INIT_RADIX_TREE(&brd->brd_pages, GFP_ATOMIC);
@@ -422,16 +440,18 @@
 	/* Tell the block layer that this is not a rotational device */
 	blk_queue_flag_set(QUEUE_FLAG_NONROT, disk->queue);
 	blk_queue_flag_clear(QUEUE_FLAG_ADD_RANDOM, disk->queue);
-	add_disk(disk);
+	blk_queue_flag_set(QUEUE_FLAG_NOWAIT, disk->queue);
+	err = add_disk(disk);
+	if (err)
+		goto out_cleanup_disk;
 
 	return 0;
 
+out_cleanup_disk:
+	blk_cleanup_disk(disk);
 out_free_dev:
-	mutex_lock(&brd_devices_mutex);
-	list_del(&brd->brd_list);
-	mutex_unlock(&brd_devices_mutex);
-	kfree(brd);
-	return -ENOMEM;
+	brd_free_device(brd);
+	return err;
 }
 
 static void brd_probe(dev_t dev)
@@ -439,15 +459,18 @@
 	brd_alloc(MINOR(dev) / max_part);
 }
 
-static void brd_del_one(struct brd_device *brd)
+static void brd_cleanup(void)
 {
-	del_gendisk(brd->brd_disk);
-	blk_cleanup_disk(brd->brd_disk);
-	brd_free_pages(brd);
-	mutex_lock(&brd_devices_mutex);
-	list_del(&brd->brd_list);
-	mutex_unlock(&brd_devices_mutex);
-	kfree(brd);
+	struct brd_device *brd, *next;
+
+	debugfs_remove_recursive(brd_debugfs_dir);
+
+	list_for_each_entry_safe(brd, next, &brd_devices, brd_list) {
+		del_gendisk(brd->brd_disk);
+		blk_cleanup_disk(brd->brd_disk);
+		brd_free_pages(brd);
+		brd_free_device(brd);
+	}
 }
 
 static inline void brd_check_and_reset_par(void)
@@ -471,7 +494,6 @@
 
 static int __init brd_init(void)
 {
-	struct brd_device *brd, *next;
 	int err, i;
 
 	/*
@@ -489,28 +511,23 @@
 	 *	dynamically.
 	 */
 
-	if (__register_blkdev(RAMDISK_MAJOR, "ramdisk", brd_probe))
-		return -EIO;
-
 	brd_check_and_reset_par();
 
 	brd_debugfs_dir = debugfs_create_dir("ramdisk_pages", NULL);
 
-	for (i = 0; i < rd_nr; i++) {
-		err = brd_alloc(i);
-		if (err)
-			goto out_free;
+	if (__register_blkdev(RAMDISK_MAJOR, "ramdisk", brd_probe)) {
+		err = -EIO;
+		goto out_free;
 	}
 
+	for (i = 0; i < rd_nr; i++)
+		brd_alloc(i);
+
 	pr_info("brd: module loaded\n");
 	return 0;
 
 out_free:
-	unregister_blkdev(RAMDISK_MAJOR, "ramdisk");
-	debugfs_remove_recursive(brd_debugfs_dir);
-
-	list_for_each_entry_safe(brd, next, &brd_devices, brd_list)
-		brd_del_one(brd);
+	brd_cleanup();
 
 	pr_info("brd: module NOT loaded !!!\n");
 	return err;
@@ -518,13 +535,9 @@
 
 static void __exit brd_exit(void)
 {
-	struct brd_device *brd, *next;
 
 	unregister_blkdev(RAMDISK_MAJOR, "ramdisk");
-	debugfs_remove_recursive(brd_debugfs_dir);
-
-	list_for_each_entry_safe(brd, next, &brd_devices, brd_list)
-		brd_del_one(brd);
+	brd_cleanup();
 
 	pr_info("brd: module unloaded\n");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_int.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_int.h
@@ -1642,22 +1642,22 @@
 };
 void drbd_bcast_event(struct drbd_device *device, const struct sib_info *sib);
 
-extern void notify_resource_state(struct sk_buff *,
+extern int notify_resource_state(struct sk_buff *,
 				  unsigned int,
 				  struct drbd_resource *,
 				  struct resource_info *,
 				  enum drbd_notification_type);
-extern void notify_device_state(struct sk_buff *,
+extern int notify_device_state(struct sk_buff *,
 				unsigned int,
 				struct drbd_device *,
 				struct device_info *,
 				enum drbd_notification_type);
-extern void notify_connection_state(struct sk_buff *,
+extern int notify_connection_state(struct sk_buff *,
 				    unsigned int,
 				    struct drbd_connection *,
 				    struct connection_info *,
 				    enum drbd_notification_type);
-extern void notify_peer_device_state(struct sk_buff *,
+extern int notify_peer_device_state(struct sk_buff *,
 				     unsigned int,
 				     struct drbd_peer_device *,
 				     struct peer_device_info *,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_main.c
@@ -171,7 +171,7 @@
 		unsigned int set_size)
 {
 	struct drbd_request *r;
-	struct drbd_request *req = NULL;
+	struct drbd_request *req = NULL, *tmp = NULL;
 	int expect_epoch = 0;
 	int expect_size = 0;
 
@@ -225,8 +225,11 @@
 	 * to catch requests being barrier-acked "unexpectedly".
 	 * It usually should find the same req again, or some READ preceding it. */
 	list_for_each_entry(req, &connection->transfer_log, tl_requests)
-		if (req->epoch == expect_epoch)
+		if (req->epoch == expect_epoch) {
+			tmp = req;
 			break;
+		}
+	req = list_prepare_entry(tmp, &connection->transfer_log, tl_requests);
 	list_for_each_entry_safe_from(req, r, &connection->transfer_log, tl_requests) {
 		if (req->epoch != expect_epoch)
 			break;
@@ -2241,7 +2244,8 @@
 		kref_put(&peer_device->connection->kref, drbd_destroy_connection);
 		kfree(peer_device);
 	}
-	memset(device, 0xfd, sizeof(*device));
+	if (device->submit.wq)
+		destroy_workqueue(device->submit.wq);
 	kfree(device);
 	kref_put(&resource->kref, drbd_destroy_resource);
 }
@@ -2333,7 +2337,6 @@
 	idr_destroy(&resource->devices);
 	free_cpumask_var(resource->cpu_mask);
 	kfree(resource->name);
-	memset(resource, 0xf2, sizeof(*resource));
 	kfree(resource);
 }
 
@@ -2674,7 +2677,6 @@
 	drbd_free_socket(&connection->data);
 	kfree(connection->int_dig_in);
 	kfree(connection->int_dig_vv);
-	memset(connection, 0xfc, sizeof(*connection));
 	kfree(connection);
 	kref_put(&resource->kref, drbd_destroy_resource);
 }
@@ -2696,7 +2698,7 @@
 enum drbd_ret_code drbd_create_device(struct drbd_config_context *adm_ctx, unsigned int minor)
 {
 	struct drbd_resource *resource = adm_ctx->resource;
-	struct drbd_connection *connection;
+	struct drbd_connection *connection, *n;
 	struct drbd_device *device;
 	struct drbd_peer_device *peer_device, *tmp_peer_device;
 	struct gendisk *disk;
@@ -2737,6 +2739,7 @@
 	sprintf(disk->disk_name, "drbd%d", minor);
 	disk->private_data = device;
 
+	blk_queue_flag_set(QUEUE_FLAG_STABLE_WRITES, disk->queue);
 	blk_queue_write_cache(disk->queue, true, true);
 	/* Setting the max_hw_sectors to an odd value of 8kibyte here
 	   This triggers a max_bio_size message upon first attach or connect */
@@ -2791,10 +2794,12 @@
 
 	if (init_submitter(device)) {
 		err = ERR_NOMEM;
-		goto out_idr_remove_vol;
+		goto out_idr_remove_from_resource;
 	}
 
-	add_disk(disk);
+	err = add_disk(disk);
+	if (err)
+		goto out_destroy_workqueue;
 
 	/* inherit the connection state */
 	device->state.conn = first_connection(resource)->cstate;
@@ -2808,10 +2813,10 @@
 	drbd_debugfs_device_add(device);
 	return NO_ERROR;
 
-out_idr_remove_vol:
-	idr_remove(&connection->peer_devices, vnr);
+out_destroy_workqueue:
+	destroy_workqueue(device->submit.wq);
 out_idr_remove_from_resource:
-	for_each_connection(connection, resource) {
+	for_each_connection_safe(connection, n, resource) {
 		peer_device = idr_remove(&connection->peer_devices, vnr);
 		if (peer_device)
 			kref_put(&connection->kref, drbd_destroy_connection);
@@ -3401,10 +3406,12 @@
 void drbd_uuid_set_bm(struct drbd_device *device, u64 val) __must_hold(local)
 {
 	unsigned long flags;
-	if (device->ldev->md.uuid[UI_BITMAP] == 0 && val == 0)
+	spin_lock_irqsave(&device->ldev->md.uuid_lock, flags);
+	if (device->ldev->md.uuid[UI_BITMAP] == 0 && val == 0) {
+		spin_unlock_irqrestore(&device->ldev->md.uuid_lock, flags);
 		return;
+	}
 
-	spin_lock_irqsave(&device->ldev->md.uuid_lock, flags);
 	if (val == 0) {
 		drbd_uuid_move_history(device);
 		device->ldev->md.uuid[UI_HISTORY_START] = device->ldev->md.uuid[UI_BITMAP];
@@ -3603,9 +3610,8 @@
 	 * when we want to support more than
 	 * one PRO_VERSION */
 	static const char *cmdnames[] = {
+
 		[P_DATA]	        = "Data",
-		[P_WSAME]	        = "WriteSame",
-		[P_TRIM]	        = "Trim",
 		[P_DATA_REPLY]	        = "DataReply",
 		[P_RS_DATA_REPLY]	= "RSDataReply",
 		[P_BARRIER]	        = "Barrier",
@@ -3616,7 +3622,6 @@
 		[P_DATA_REQUEST]	= "DataRequest",
 		[P_RS_DATA_REQUEST]     = "RSDataRequest",
 		[P_SYNC_PARAM]	        = "SyncParam",
-		[P_SYNC_PARAM89]	= "SyncParam89",
 		[P_PROTOCOL]            = "ReportProtocol",
 		[P_UUIDS]	        = "ReportUUIDs",
 		[P_SIZES]	        = "ReportSizes",
@@ -3624,6 +3629,7 @@
 		[P_SYNC_UUID]           = "ReportSyncUUID",
 		[P_AUTH_CHALLENGE]      = "AuthChallenge",
 		[P_AUTH_RESPONSE]	= "AuthResponse",
+		[P_STATE_CHG_REQ]       = "StateChgRequest",
 		[P_PING]		= "Ping",
 		[P_PING_ACK]	        = "PingAck",
 		[P_RECV_ACK]	        = "RecvAck",
@@ -3634,23 +3640,25 @@
 		[P_NEG_DREPLY]	        = "NegDReply",
 		[P_NEG_RS_DREPLY]	= "NegRSDReply",
 		[P_BARRIER_ACK]	        = "BarrierAck",
-		[P_STATE_CHG_REQ]       = "StateChgRequest",
 		[P_STATE_CHG_REPLY]     = "StateChgReply",
 		[P_OV_REQUEST]          = "OVRequest",
 		[P_OV_REPLY]            = "OVReply",
 		[P_OV_RESULT]           = "OVResult",
 		[P_CSUM_RS_REQUEST]     = "CsumRSRequest",
 		[P_RS_IS_IN_SYNC]	= "CsumRSIsInSync",
+		[P_SYNC_PARAM89]	= "SyncParam89",
 		[P_COMPRESSED_BITMAP]   = "CBitmap",
 		[P_DELAY_PROBE]         = "DelayProbe",
 		[P_OUT_OF_SYNC]		= "OutOfSync",
-		[P_RETRY_WRITE]		= "RetryWrite",
 		[P_RS_CANCEL]		= "RSCancel",
 		[P_CONN_ST_CHG_REQ]	= "conn_st_chg_req",
 		[P_CONN_ST_CHG_REPLY]	= "conn_st_chg_reply",
 		[P_PROTOCOL_UPDATE]	= "protocol_update",
+		[P_TRIM]	        = "Trim",
 		[P_RS_THIN_REQ]         = "rs_thin_req",
 		[P_RS_DEALLOCATED]      = "rs_deallocated",
+		[P_WSAME]	        = "WriteSame",
+		[P_ZEROES]		= "Zeroes",
 
 		/* enum drbd_packet, but not commands - obsoleted flags:
 		 *	P_MAY_IGNORE
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_nl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_nl.c
@@ -4617,7 +4617,7 @@
 	return drbd_notification_header_to_skb(msg, &nh, true);
 }
 
-void notify_resource_state(struct sk_buff *skb,
+int notify_resource_state(struct sk_buff *skb,
 			   unsigned int seq,
 			   struct drbd_resource *resource,
 			   struct resource_info *resource_info,
@@ -4659,16 +4659,17 @@
 		if (err && err != -ESRCH)
 			goto failed;
 	}
-	return;
+	return 0;
 
 nla_put_failure:
 	nlmsg_free(skb);
 failed:
 	drbd_err(resource, "Error %d while broadcasting event. Event seq:%u\n",
 			err, seq);
+	return err;
 }
 
-void notify_device_state(struct sk_buff *skb,
+int notify_device_state(struct sk_buff *skb,
 			 unsigned int seq,
 			 struct drbd_device *device,
 			 struct device_info *device_info,
@@ -4708,16 +4709,17 @@
 		if (err && err != -ESRCH)
 			goto failed;
 	}
-	return;
+	return 0;
 
 nla_put_failure:
 	nlmsg_free(skb);
 failed:
 	drbd_err(device, "Error %d while broadcasting event. Event seq:%u\n",
 		 err, seq);
+	return err;
 }
 
-void notify_connection_state(struct sk_buff *skb,
+int notify_connection_state(struct sk_buff *skb,
 			     unsigned int seq,
 			     struct drbd_connection *connection,
 			     struct connection_info *connection_info,
@@ -4757,16 +4759,17 @@
 		if (err && err != -ESRCH)
 			goto failed;
 	}
-	return;
+	return 0;
 
 nla_put_failure:
 	nlmsg_free(skb);
 failed:
 	drbd_err(connection, "Error %d while broadcasting event. Event seq:%u\n",
 		 err, seq);
+	return err;
 }
 
-void notify_peer_device_state(struct sk_buff *skb,
+int notify_peer_device_state(struct sk_buff *skb,
 			      unsigned int seq,
 			      struct drbd_peer_device *peer_device,
 			      struct peer_device_info *peer_device_info,
@@ -4807,13 +4810,14 @@
 		if (err && err != -ESRCH)
 			goto failed;
 	}
-	return;
+	return 0;
 
 nla_put_failure:
 	nlmsg_free(skb);
 failed:
 	drbd_err(peer_device, "Error %d while broadcasting event. Event seq:%u\n",
 		 err, seq);
+	return err;
 }
 
 void notify_helper(enum drbd_notification_type type,
@@ -4864,7 +4868,7 @@
 		 err, seq);
 }
 
-static void notify_initial_state_done(struct sk_buff *skb, unsigned int seq)
+static int notify_initial_state_done(struct sk_buff *skb, unsigned int seq)
 {
 	struct drbd_genlmsghdr *dh;
 	int err;
@@ -4878,11 +4882,12 @@
 	if (nla_put_notification_header(skb, NOTIFY_EXISTS))
 		goto nla_put_failure;
 	genlmsg_end(skb, dh);
-	return;
+	return 0;
 
 nla_put_failure:
 	nlmsg_free(skb);
 	pr_err("Error %d sending event. Event seq:%u\n", err, seq);
+	return err;
 }
 
 static void free_state_changes(struct list_head *list)
@@ -4909,6 +4914,7 @@
 	unsigned int seq = cb->args[2];
 	unsigned int n;
 	enum drbd_notification_type flags = 0;
+	int err = 0;
 
 	/* There is no need for taking notification_mutex here: it doesn't
 	   matter if the initial state events mix with later state chage
@@ -4917,32 +4923,32 @@
 
 	cb->args[5]--;
 	if (cb->args[5] == 1) {
-		notify_initial_state_done(skb, seq);
+		err = notify_initial_state_done(skb, seq);
 		goto out;
 	}
 	n = cb->args[4]++;
 	if (cb->args[4] < cb->args[3])
 		flags |= NOTIFY_CONTINUES;
 	if (n < 1) {
-		notify_resource_state_change(skb, seq, state_change->resource,
+		err = notify_resource_state_change(skb, seq, state_change->resource,
 					     NOTIFY_EXISTS | flags);
 		goto next;
 	}
 	n--;
 	if (n < state_change->n_connections) {
-		notify_connection_state_change(skb, seq, &state_change->connections[n],
+		err = notify_connection_state_change(skb, seq, &state_change->connections[n],
 					       NOTIFY_EXISTS | flags);
 		goto next;
 	}
 	n -= state_change->n_connections;
 	if (n < state_change->n_devices) {
-		notify_device_state_change(skb, seq, &state_change->devices[n],
+		err = notify_device_state_change(skb, seq, &state_change->devices[n],
 					   NOTIFY_EXISTS | flags);
 		goto next;
 	}
 	n -= state_change->n_devices;
 	if (n < state_change->n_devices * state_change->n_connections) {
-		notify_peer_device_state_change(skb, seq, &state_change->peer_devices[n],
+		err = notify_peer_device_state_change(skb, seq, &state_change->peer_devices[n],
 						NOTIFY_EXISTS | flags);
 		goto next;
 	}
@@ -4957,7 +4963,10 @@
 		cb->args[4] = 0;
 	}
 out:
-	return skb->len;
+	if (err)
+		return err;
+	else
+		return skb->len;
 }
 
 int drbd_adm_get_initial_state(struct sk_buff *skb, struct netlink_callback *cb)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_receiver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_receiver.c
@@ -1301,7 +1301,7 @@
 	bio_set_dev(bio, device->ldev->backing_bdev);
 	bio->bi_private = octx;
 	bio->bi_end_io = one_flush_endio;
-	bio->bi_opf = REQ_OP_FLUSH | REQ_PREFLUSH;
+	bio->bi_opf = REQ_OP_WRITE | REQ_PREFLUSH;
 
 	device->flush_jif = jiffies;
 	set_bit(FLUSH_PENDING, &device->flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_req.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_req.c
@@ -180,7 +180,8 @@
 void complete_master_bio(struct drbd_device *device,
 		struct bio_and_error *m)
 {
-	m->bio->bi_status = errno_to_blk_status(m->error);
+	if (unlikely(m->error))
+		m->bio->bi_status = errno_to_blk_status(m->error);
 	bio_endio(m->bio);
 	dec_ap_bio(device);
 }
@@ -1601,6 +1602,8 @@
 	struct drbd_device *device = bio->bi_bdev->bd_disk->private_data;
 
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
 	/*
 	 * what we "blindly" assume:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_state.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_state.c
@@ -876,7 +876,7 @@
 		  ns.disk == D_OUTDATED)
 		rv = SS_CONNECTED_OUTDATES;
 
-	else if ((ns.conn == C_VERIFY_S || ns.conn == C_VERIFY_T) &&
+	else if (nc && (ns.conn == C_VERIFY_S || ns.conn == C_VERIFY_T) &&
 		 (nc->verify_alg[0] == 0))
 		rv = SS_NO_VERIFY_ALG;
 
@@ -1537,7 +1537,7 @@
 	return rv;
 }
 
-void notify_resource_state_change(struct sk_buff *skb,
+int notify_resource_state_change(struct sk_buff *skb,
 				  unsigned int seq,
 				  struct drbd_resource_state_change *resource_state_change,
 				  enum drbd_notification_type type)
@@ -1550,10 +1550,10 @@
 		.res_susp_fen = resource_state_change->susp_fen[NEW],
 	};
 
-	notify_resource_state(skb, seq, resource, &resource_info, type);
+	return notify_resource_state(skb, seq, resource, &resource_info, type);
 }
 
-void notify_connection_state_change(struct sk_buff *skb,
+int notify_connection_state_change(struct sk_buff *skb,
 				    unsigned int seq,
 				    struct drbd_connection_state_change *connection_state_change,
 				    enum drbd_notification_type type)
@@ -1564,10 +1564,10 @@
 		.conn_role = connection_state_change->peer_role[NEW],
 	};
 
-	notify_connection_state(skb, seq, connection, &connection_info, type);
+	return notify_connection_state(skb, seq, connection, &connection_info, type);
 }
 
-void notify_device_state_change(struct sk_buff *skb,
+int notify_device_state_change(struct sk_buff *skb,
 				unsigned int seq,
 				struct drbd_device_state_change *device_state_change,
 				enum drbd_notification_type type)
@@ -1577,10 +1577,10 @@
 		.dev_disk_state = device_state_change->disk_state[NEW],
 	};
 
-	notify_device_state(skb, seq, device, &device_info, type);
+	return notify_device_state(skb, seq, device, &device_info, type);
 }
 
-void notify_peer_device_state_change(struct sk_buff *skb,
+int notify_peer_device_state_change(struct sk_buff *skb,
 				     unsigned int seq,
 				     struct drbd_peer_device_state_change *p,
 				     enum drbd_notification_type type)
@@ -1594,7 +1594,7 @@
 		.peer_resync_susp_dependency = p->resync_susp_dependency[NEW],
 	};
 
-	notify_peer_device_state(skb, seq, peer_device, &peer_device_info, type);
+	return notify_peer_device_state(skb, seq, peer_device, &peer_device_info, type);
 }
 
 static void broadcast_state_change(struct drbd_state_change *state_change)
@@ -1602,7 +1602,7 @@
 	struct drbd_resource_state_change *resource_state_change = &state_change->resource[0];
 	bool resource_state_has_changed;
 	unsigned int n_device, n_connection, n_peer_device, n_peer_devices;
-	void (*last_func)(struct sk_buff *, unsigned int, void *,
+	int (*last_func)(struct sk_buff *, unsigned int, void *,
 			  enum drbd_notification_type) = NULL;
 	void *last_arg = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/drbd/drbd_state_change.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/drbd/drbd_state_change.h
@@ -44,19 +44,19 @@
 extern void copy_old_to_new_state_change(struct drbd_state_change *);
 extern void forget_state_change(struct drbd_state_change *);
 
-extern void notify_resource_state_change(struct sk_buff *,
+extern int notify_resource_state_change(struct sk_buff *,
 					 unsigned int,
 					 struct drbd_resource_state_change *,
 					 enum drbd_notification_type type);
-extern void notify_connection_state_change(struct sk_buff *,
+extern int notify_connection_state_change(struct sk_buff *,
 					   unsigned int,
 					   struct drbd_connection_state_change *,
 					   enum drbd_notification_type type);
-extern void notify_device_state_change(struct sk_buff *,
+extern int notify_device_state_change(struct sk_buff *,
 				       unsigned int,
 				       struct drbd_device_state_change *,
 				       enum drbd_notification_type type);
-extern void notify_peer_device_state_change(struct sk_buff *,
+extern int notify_peer_device_state_change(struct sk_buff *,
 					    unsigned int,
 					    struct drbd_peer_device_state_change *,
 					    enum drbd_notification_type type);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/floppy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/floppy.c
@@ -184,6 +184,7 @@
 #include <linux/ioport.h>
 #include <linux/interrupt.h>
 #include <linux/init.h>
+#include <linux/major.h>
 #include <linux/platform_device.h>
 #include <linux/mod_devicetable.h>
 #include <linux/mutex.h>
@@ -508,8 +509,8 @@
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -529,7 +530,6 @@
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1014,7 +1014,7 @@
 static void cancel_activity(void)
 {
 	do_floppy = NULL;
-	cancel_delayed_work_sync(&fd_timer);
+	cancel_delayed_work(&fd_timer);
 	cancel_work_sync(&floppy_work);
 }
 
@@ -1454,7 +1454,7 @@
 			if (drive_params[current_drive].flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= drive_params[current_drive].max_errors.reporting) {
+		} else if (floppy_errors >= drive_params[current_drive].max_errors.reporting) {
 			print_errors();
 		}
 		if (reply_buffer[ST2] & ST2_WC || reply_buffer[ST2] & ST2_BC)
@@ -2094,7 +2094,7 @@
 		if (!next_valid_format(current_drive))
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(write_errors[current_drive].badness, err_count);
 	if (err_count > drive_params[current_drive].max_errors.abort)
 		cont->done(0);
@@ -2240,9 +2240,8 @@
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2760,10 +2759,11 @@
 	current_req = list_first_entry_or_null(&floppy_reqs, struct request,
 					       queuelist);
 	if (current_req) {
-		current_req->error_count = 0;
+		floppy_errors = 0;
 		list_del_init(&current_req->queuelist);
+		return 1;
 	}
-	return current_req != NULL;
+	return 0;
 }
 
 /* Starts or continues processing request. Will automatically unlock the
@@ -2822,7 +2822,6 @@
 		_floppy = floppy_type + drive_params[current_drive].autodetect[drive_state[current_drive].probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->error_count);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
@@ -2983,6 +2982,8 @@
 		return "(null)";
 }
 
+#ifdef CONFIG_BLK_DEV_FD_RAWCMD
+
 /* raw commands */
 static void raw_cmd_done(int flag)
 {
@@ -3080,6 +3081,8 @@
 	}
 }
 
+#define MAX_LEN (1UL << MAX_ORDER << PAGE_SHIFT)
+
 static int raw_cmd_copyin(int cmd, void __user *param,
 				 struct floppy_raw_cmd **rcmd)
 {
@@ -3107,7 +3110,7 @@
 	ptr->resultcode = 0;
 
 	if (ptr->flags & (FD_RAW_READ | FD_RAW_WRITE)) {
-		if (ptr->length <= 0)
+		if (ptr->length <= 0 || ptr->length >= MAX_LEN)
 			return -EINVAL;
 		ptr->kernel_data = (char *)fd_dma_mem_alloc(ptr->length);
 		fallback_on_nodma_alloc(&ptr->kernel_data, ptr->length);
@@ -3180,6 +3183,35 @@
 	return ret;
 }
 
+static int floppy_raw_cmd_ioctl(int type, int drive, int cmd,
+				void __user *param)
+{
+	int ret;
+
+	pr_warn_once("Note: FDRAWCMD is deprecated and will be removed from the kernel in the near future.\n");
+
+	if (type)
+		return -EINVAL;
+	if (lock_fdc(drive))
+		return -EINTR;
+	set_floppy(drive);
+	ret = raw_cmd_ioctl(cmd, param);
+	if (ret == -EINTR)
+		return -EINTR;
+	process_fd_request();
+	return ret;
+}
+
+#else /* CONFIG_BLK_DEV_FD_RAWCMD */
+
+static int floppy_raw_cmd_ioctl(int type, int drive, int cmd,
+				void __user *param)
+{
+	return -EOPNOTSUPP;
+}
+
+#endif
+
 static int invalidate_drive(struct block_device *bdev)
 {
 	/* invalidate the buffer track to force a reread */
@@ -3368,7 +3400,6 @@
 {
 	int drive = (long)bdev->bd_disk->private_data;
 	int type = ITYPE(drive_state[drive].fd_device);
-	int i;
 	int ret;
 	int size;
 	union inparam {
@@ -3519,16 +3550,7 @@
 		outparam = &write_errors[drive];
 		break;
 	case FDRAWCMD:
-		if (type)
-			return -EINVAL;
-		if (lock_fdc(drive))
-			return -EINTR;
-		set_floppy(drive);
-		i = raw_cmd_ioctl(cmd, (void __user *)param);
-		if (i == -EINTR)
-			return -EINTR;
-		process_fd_request();
-		return i;
+		return floppy_raw_cmd_ioctl(type, drive, cmd, (void __user *)param);
 	case FDTWADDLE:
 		if (lock_fdc(drive))
 			return -EINTR;
@@ -4478,6 +4500,7 @@
 };
 
 static struct platform_device floppy_device[N_DRIVE];
+static bool registered[N_DRIVE];
 
 static bool floppy_available(int drive)
 {
@@ -4564,8 +4587,10 @@
 			goto out_put_disk;
 
 		err = floppy_alloc_disk(drive, 0);
-		if (err)
+		if (err) {
+			blk_mq_free_tag_set(&tag_sets[drive]);
 			goto out_put_disk;
+		}
 
 		timer_setup(&motor_off_timer[drive], motor_off_callback, 0);
 	}
@@ -4693,6 +4718,8 @@
 		if (err)
 			goto out_remove_drives;
 
+		registered[drive] = true;
+
 		device_add_disk(&floppy_device[drive].dev, disks[drive][0],
 				NULL);
 	}
@@ -4703,7 +4730,8 @@
 	while (drive--) {
 		if (floppy_available(drive)) {
 			del_gendisk(disks[drive][0]);
-			platform_device_unregister(&floppy_device[drive]);
+			if (registered[drive])
+				platform_device_unregister(&floppy_device[drive]);
 		}
 	}
 out_release_dma:
@@ -4946,26 +4974,14 @@
 				if (disks[drive][i])
 					del_gendisk(disks[drive][i]);
 			}
-			platform_device_unregister(&floppy_device[drive]);
+			if (registered[drive])
+				platform_device_unregister(&floppy_device[drive]);
 		}
 		for (i = 0; i < ARRAY_SIZE(floppy_type); i++) {
 			if (disks[drive][i])
 				blk_cleanup_queue(disks[drive][i]->queue);
 		}
 		blk_mq_free_tag_set(&tag_sets[drive]);
-
-		/*
-		 * These disks have not called add_disk().  Don't put down
-		 * queue reference in put_disk().
-		 */
-		if (!(allowed_drive_mask & (1 << drive)) ||
-		    fdc_state[FDC(drive)].version == FDC_NONE) {
-			for (i = 0; i < ARRAY_SIZE(floppy_type); i++) {
-				if (disks[drive][i])
-					disks[drive][i]->queue = NULL;
-			}
-		}
-
 		for (i = 0; i < ARRAY_SIZE(floppy_type); i++) {
 			if (disks[drive][i])
 				put_disk(disks[drive][i]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/loop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/loop.c
@@ -79,6 +79,7 @@
 #include <linux/ioprio.h>
 #include <linux/blk-cgroup.h>
 #include <linux/sched/mm.h>
+#include <linux/statfs.h>
 
 #include "loop.h"
 
@@ -273,19 +274,6 @@
 }
 
 /**
- * loop_validate_block_size() - validates the passed in block size
- * @bsize: size to validate
- */
-static int
-loop_validate_block_size(unsigned short bsize)
-{
-	if (bsize < 512 || bsize > PAGE_SIZE || !is_power_of_2(bsize))
-		return -EINVAL;
-
-	return 0;
-}
-
-/**
  * loop_set_size() - sets device size and notifies userspace
  * @lo: struct loop_device to set the size for
  * @size: new size of the loop device
@@ -685,6 +673,15 @@
 				lo->use_dio);
 }
 
+static struct file *loop_real_file(struct file *file)
+{
+	struct file *f = NULL;
+
+	if (file->f_path.dentry->d_sb->s_op->real_loop)
+		f = file->f_path.dentry->d_sb->s_op->real_loop(file);
+	return f;
+}
+
 static void loop_reread_partitions(struct loop_device *lo)
 {
 	int rc;
@@ -742,12 +739,17 @@
 {
 	struct file *file = fget(arg);
 	struct file *old_file;
+	struct file *f, *virt_file = NULL, *old_virt_file;
 	int error;
 	bool partscan;
 	bool is_loop;
 
 	if (!file)
 		return -EBADF;
+
+	/* suppress uevents while reconfiguring the device */
+	dev_set_uevent_suppress(disk_to_dev(lo->lo_disk), 1);
+
 	is_loop = is_loop_device(file);
 	error = loop_global_lock_killable(lo, is_loop);
 	if (error)
@@ -761,11 +763,19 @@
 	if (!(lo->lo_flags & LO_FLAGS_READ_ONLY))
 		goto out_err;
 
+	f = loop_real_file(file);
+	if (f) {
+		virt_file = file;
+		file = f;
+		get_file(file);
+	}
+
 	error = loop_validate_file(file, bdev);
 	if (error)
 		goto out_err;
 
 	old_file = lo->lo_backing_file;
+	old_virt_file = lo->lo_backing_virt_file;
 
 	error = -EINVAL;
 
@@ -778,6 +788,7 @@
 	blk_mq_freeze_queue(lo->lo_queue);
 	mapping_set_gfp_mask(old_file->f_mapping, lo->old_gfp_mask);
 	lo->lo_backing_file = file;
+	lo->lo_backing_virt_file = virt_file;
 	lo->old_gfp_mask = mapping_gfp_mask(file->f_mapping);
 	mapping_set_gfp_mask(file->f_mapping,
 			     lo->old_gfp_mask & ~(__GFP_IO|__GFP_FS));
@@ -800,17 +811,44 @@
 	 * dependency.
 	 */
 	fput(old_file);
+	if (old_virt_file)
+		fput(old_virt_file);
 	if (partscan)
 		loop_reread_partitions(lo);
-	return 0;
+
+	error = 0;
+done:
+	/* enable and uncork uevent now that we are done */
+	dev_set_uevent_suppress(disk_to_dev(lo->lo_disk), 0);
+	return error;
 
 out_err:
 	loop_global_unlock(lo, is_loop);
 out_putf:
 	fput(file);
-	return error;
+	if (virt_file)
+		fput(virt_file);
+	goto done;
 }
 
+/*
+ * for AUFS
+ * no get/put for file.
+ */
+struct file *loop_backing_file(struct super_block *sb)
+{
+	struct file *ret;
+	struct loop_device *l;
+
+	ret = NULL;
+	if (MAJOR(sb->s_dev) == LOOP_MAJOR) {
+		l = sb->s_bdev->bd_disk->private_data;
+		ret = l->lo_backing_file;
+	}
+	return ret;
+}
+EXPORT_SYMBOL_GPL(loop_backing_file);
+
 /* loop sysfs attributes */
 
 static ssize_t loop_attr_show(struct device *dev, char *page,
@@ -856,33 +894,33 @@
 
 static ssize_t loop_attr_offset_show(struct loop_device *lo, char *buf)
 {
-	return sprintf(buf, "%llu\n", (unsigned long long)lo->lo_offset);
+	return sysfs_emit(buf, "%llu\n", (unsigned long long)lo->lo_offset);
 }
 
 static ssize_t loop_attr_sizelimit_show(struct loop_device *lo, char *buf)
 {
-	return sprintf(buf, "%llu\n", (unsigned long long)lo->lo_sizelimit);
+	return sysfs_emit(buf, "%llu\n", (unsigned long long)lo->lo_sizelimit);
 }
 
 static ssize_t loop_attr_autoclear_show(struct loop_device *lo, char *buf)
 {
 	int autoclear = (lo->lo_flags & LO_FLAGS_AUTOCLEAR);
 
-	return sprintf(buf, "%s\n", autoclear ? "1" : "0");
+	return sysfs_emit(buf, "%s\n", autoclear ? "1" : "0");
 }
 
 static ssize_t loop_attr_partscan_show(struct loop_device *lo, char *buf)
 {
 	int partscan = (lo->lo_flags & LO_FLAGS_PARTSCAN);
 
-	return sprintf(buf, "%s\n", partscan ? "1" : "0");
+	return sysfs_emit(buf, "%s\n", partscan ? "1" : "0");
 }
 
 static ssize_t loop_attr_dio_show(struct loop_device *lo, char *buf)
 {
 	int dio = (lo->lo_flags & LO_FLAGS_DIRECT_IO);
 
-	return sprintf(buf, "%s\n", dio ? "1" : "0");
+	return sysfs_emit(buf, "%s\n", dio ? "1" : "0");
 }
 
 LOOP_ATTR_RO(backing_file);
@@ -952,8 +990,13 @@
 		granularity = 0;
 
 	} else {
+		struct kstatfs sbuf;
+
 		max_discard_sectors = UINT_MAX >> 9;
-		granularity = inode->i_sb->s_blocksize;
+		if (!vfs_statfs(&file->f_path, &sbuf))
+			granularity = sbuf.f_bsize;
+		else
+			max_discard_sectors = 0;
 	}
 
 	if (max_discard_sectors) {
@@ -1159,8 +1202,13 @@
 	if (err)
 		return err;
 
+	/* Avoid assigning overflow values */
+	if (info->lo_offset > LLONG_MAX || info->lo_sizelimit > LLONG_MAX)
+		return -EOVERFLOW;
+
 	lo->lo_offset = info->lo_offset;
 	lo->lo_sizelimit = info->lo_sizelimit;
+
 	memcpy(lo->lo_file_name, info->lo_file_name, LO_NAME_SIZE);
 	memcpy(lo->lo_crypt_name, info->lo_crypt_name, LO_NAME_SIZE);
 	lo->lo_file_name[LO_NAME_SIZE-1] = 0;
@@ -1190,6 +1238,7 @@
 			  const struct loop_config *config)
 {
 	struct file *file = fget(config->fd);
+	struct file *f, *virt_file = NULL;
 	struct inode *inode;
 	struct address_space *mapping;
 	int error;
@@ -1205,6 +1254,13 @@
 	/* This is safe, since we have a reference from open(). */
 	__module_get(THIS_MODULE);
 
+	f = loop_real_file(file);
+	if (f) {
+		virt_file = file;
+		file = f;
+		get_file(file);
+	}
+
 	/*
 	 * If we don't hold exclusive handle for the device, upgrade to it
 	 * here to avoid changing device under exclusive owner.
@@ -1236,7 +1292,7 @@
 	}
 
 	if (config->block_size) {
-		error = loop_validate_block_size(config->block_size);
+		error = blk_validate_block_size(config->block_size);
 		if (error)
 			goto out_unlock;
 	}
@@ -1258,6 +1314,9 @@
 		goto out_unlock;
 	}
 
+	/* suppress uevents while reconfiguring the device */
+	dev_set_uevent_suppress(disk_to_dev(lo->lo_disk), 1);
+
 	disk_force_media_change(lo->lo_disk, DISK_EVENT_MEDIA_CHANGE);
 	set_disk_ro(lo->lo_disk, (lo->lo_flags & LO_FLAGS_READ_ONLY) != 0);
 
@@ -1270,6 +1329,7 @@
 	lo->use_dio = lo->lo_flags & LO_FLAGS_DIRECT_IO;
 	lo->lo_device = bdev;
 	lo->lo_backing_file = file;
+	lo->lo_backing_virt_file = virt_file;
 	lo->old_gfp_mask = mapping_gfp_mask(mapping);
 	mapping_set_gfp_mask(mapping, lo->old_gfp_mask & ~(__GFP_IO|__GFP_FS));
 
@@ -1304,13 +1364,18 @@
 		lo->lo_flags |= LO_FLAGS_PARTSCAN;
 	partscan = lo->lo_flags & LO_FLAGS_PARTSCAN;
 	if (partscan)
-		lo->lo_disk->flags &= ~GENHD_FL_NO_PART_SCAN;
+		clear_bit(GD_SUPPRESS_PART_SCAN, &lo->lo_disk->state);
+
+	/* enable and uncork uevent now that we are done */
+	dev_set_uevent_suppress(disk_to_dev(lo->lo_disk), 0);
 
 	loop_global_unlock(lo, is_loop);
 	if (partscan)
 		loop_reread_partitions(lo);
+
 	if (!(mode & FMODE_EXCL))
 		bd_abort_claiming(bdev, loop_configure);
+
 	return 0;
 
 out_unlock:
@@ -1320,6 +1385,8 @@
 		bd_abort_claiming(bdev, loop_configure);
 out_putf:
 	fput(file);
+	if (virt_file)
+		fput(virt_file);
 	/* This is safe: open() is still holding a reference. */
 	module_put(THIS_MODULE);
 	return error;
@@ -1328,6 +1395,7 @@
 static int __loop_clr_fd(struct loop_device *lo, bool release)
 {
 	struct file *filp = NULL;
+	struct file *virt_filp = lo->lo_backing_virt_file;
 	gfp_t gfp = lo->old_gfp_mask;
 	struct block_device *bdev = lo->lo_device;
 	int err = 0;
@@ -1379,6 +1447,7 @@
 
 	spin_lock_irq(&lo->lo_lock);
 	lo->lo_backing_file = NULL;
+	lo->lo_backing_virt_file = NULL;
 	spin_unlock_irq(&lo->lo_lock);
 
 	loop_release_xfer(lo);
@@ -1448,7 +1517,7 @@
 	mutex_lock(&lo->lo_mutex);
 	lo->lo_flags = 0;
 	if (!part_shift)
-		lo->lo_disk->flags |= GENHD_FL_NO_PART_SCAN;
+		set_bit(GD_SUPPRESS_PART_SCAN, &lo->lo_disk->state);
 	lo->lo_state = Lo_unbound;
 	mutex_unlock(&lo->lo_mutex);
 
@@ -1459,6 +1528,8 @@
 	 */
 	if (filp)
 		fput(filp);
+	if (virt_filp)
+		fput(virt_filp);
 	return err;
 }
 
@@ -1565,7 +1636,7 @@
 
 	if (!err && (lo->lo_flags & LO_FLAGS_PARTSCAN) &&
 	     !(prev_lo_flags & LO_FLAGS_PARTSCAN)) {
-		lo->lo_disk->flags &= ~GENHD_FL_NO_PART_SCAN;
+		clear_bit(GD_SUPPRESS_PART_SCAN, &lo->lo_disk->state);
 		partscan = true;
 	}
 out_unlock:
@@ -1759,7 +1830,7 @@
 	if (lo->lo_state != Lo_bound)
 		return -ENXIO;
 
-	err = loop_validate_block_size(arg);
+	err = blk_validate_block_size(arg);
 	if (err)
 		return err;
 
@@ -2093,8 +2164,40 @@
 /*
  * And now the modules code and kernel interface.
  */
-static int max_loop;
-module_param(max_loop, int, 0444);
+
+/*
+ * If max_loop is specified, create that many devices upfront.
+ * This also becomes a hard limit. If max_loop is not specified,
+ * the default isn't a hard limit (as before commit 85c50197716c
+ * changed the default value from 0 for max_loop=0 reasons), just
+ * create CONFIG_BLK_DEV_LOOP_MIN_COUNT loop devices at module
+ * init time. Loop devices can be requested on-demand with the
+ * /dev/loop-control interface, or be instantiated by accessing
+ * a 'dead' device node.
+ */
+static int max_loop = CONFIG_BLK_DEV_LOOP_MIN_COUNT;
+
+static bool max_loop_specified;
+
+static int max_loop_param_set_int(const char *val,
+				  const struct kernel_param *kp)
+{
+	int ret;
+
+	ret = param_set_int(val, kp);
+	if (ret < 0)
+		return ret;
+
+	max_loop_specified = true;
+	return 0;
+}
+
+static const struct kernel_param_ops max_loop_param_ops = {
+	.set = max_loop_param_set_int,
+	.get = param_get_int,
+};
+
+module_param_cb(max_loop, &max_loop_param_ops, &max_loop, 0444);
 MODULE_PARM_DESC(max_loop, "Maximum number of loop devices");
 module_param(max_part, int, 0444);
 MODULE_PARM_DESC(max_part, "Maximum number of partitions per loop device");
@@ -2181,35 +2284,44 @@
 
 static void loop_handle_cmd(struct loop_cmd *cmd)
 {
+	struct cgroup_subsys_state *cmd_blkcg_css = cmd->blkcg_css;
+	struct cgroup_subsys_state *cmd_memcg_css = cmd->memcg_css;
 	struct request *rq = blk_mq_rq_from_pdu(cmd);
 	const bool write = op_is_write(req_op(rq));
 	struct loop_device *lo = rq->q->queuedata;
 	int ret = 0;
 	struct mem_cgroup *old_memcg = NULL;
+	const bool use_aio = cmd->use_aio;
 
 	if (write && (lo->lo_flags & LO_FLAGS_READ_ONLY)) {
 		ret = -EIO;
 		goto failed;
 	}
 
-	if (cmd->blkcg_css)
-		kthread_associate_blkcg(cmd->blkcg_css);
-	if (cmd->memcg_css)
+	if (cmd_blkcg_css)
+		kthread_associate_blkcg(cmd_blkcg_css);
+	if (cmd_memcg_css)
 		old_memcg = set_active_memcg(
-			mem_cgroup_from_css(cmd->memcg_css));
+			mem_cgroup_from_css(cmd_memcg_css));
 
+	/*
+	 * do_req_filebacked() may call blk_mq_complete_request() synchronously
+	 * or asynchronously if using aio. Hence, do not touch 'cmd' after
+	 * do_req_filebacked() has returned unless we are sure that 'cmd' has
+	 * not yet been completed.
+	 */
 	ret = do_req_filebacked(lo, rq);
 
-	if (cmd->blkcg_css)
+	if (cmd_blkcg_css)
 		kthread_associate_blkcg(NULL);
 
-	if (cmd->memcg_css) {
+	if (cmd_memcg_css) {
 		set_active_memcg(old_memcg);
-		css_put(cmd->memcg_css);
+		css_put(cmd_memcg_css);
 	}
  failed:
 	/* complete non-aio request */
-	if (!cmd->use_aio || ret) {
+	if (!use_aio || ret) {
 		if (ret == -EOPNOTSUPP)
 			cmd->ret = ret;
 		else
@@ -2377,7 +2489,7 @@
 	 * userspace tools. Parameters like this in general should be avoided.
 	 */
 	if (!part_shift)
-		disk->flags |= GENHD_FL_NO_PART_SCAN;
+		set_bit(GD_SUPPRESS_PART_SCAN, &disk->state);
 	disk->flags |= GENHD_FL_EXT_DEVT;
 	atomic_set(&lo->lo_refcnt, 0);
 	mutex_init(&lo->lo_mutex);
@@ -2431,7 +2543,7 @@
 {
 	int idx = MINOR(dev) >> part_shift;
 
-	if (max_loop && idx >= max_loop)
+	if (max_loop_specified && max_loop && idx >= max_loop)
 		return;
 	loop_add(idx);
 }
@@ -2442,7 +2554,7 @@
 	int ret;
 
 	if (idx < 0) {
-		pr_warn("deleting an unspecified loop device is not supported.\n");
+		pr_warn_once("deleting an unspecified loop device is not supported.\n");
 		return -EINVAL;
 	}
 		
@@ -2538,7 +2650,7 @@
 
 static int __init loop_init(void)
 {
-	int i, nr;
+	int i;
 	int err;
 
 	part_shift = 0;
@@ -2566,19 +2678,6 @@
 		goto err_out;
 	}
 
-	/*
-	 * If max_loop is specified, create that many devices upfront.
-	 * This also becomes a hard limit. If max_loop is not specified,
-	 * create CONFIG_BLK_DEV_LOOP_MIN_COUNT loop devices at module
-	 * init time. Loop devices can be requested on-demand with the
-	 * /dev/loop-control interface, or be instantiated by accessing
-	 * a 'dead' device node.
-	 */
-	if (max_loop)
-		nr = max_loop;
-	else
-		nr = CONFIG_BLK_DEV_LOOP_MIN_COUNT;
-
 	err = misc_register(&loop_misc);
 	if (err < 0)
 		goto err_out;
@@ -2590,7 +2689,7 @@
 	}
 
 	/* pre-create number of devices given by config or max_loop */
-	for (i = 0; i < nr; i++)
+	for (i = 0; i < max_loop; i++)
 		loop_add(i);
 
 	printk(KERN_INFO "loop: module loaded\n");
@@ -2629,6 +2728,7 @@
 static int __init max_loop_setup(char *str)
 {
 	max_loop = simple_strtol(str, NULL, 0);
+	max_loop_specified = true;
 	return 1;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/loop.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/loop.h
@@ -46,7 +46,7 @@
 	int		(*ioctl)(struct loop_device *, int cmd, 
 				 unsigned long arg); 
 
-	struct file *	lo_backing_file;
+	struct file	*lo_backing_file, *lo_backing_virt_file;
 	struct block_device *lo_device;
 	void		*key_data; 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/mtip32xx/mtip32xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/mtip32xx/mtip32xx.c
@@ -4112,7 +4112,7 @@
 			"Completion workers still active!\n");
 	}
 
-	blk_set_queue_dying(dd->queue);
+	blk_mark_disk_dead(dd->disk);
 	set_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag);
 
 	/* Clean up the block layer. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/n64cart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/n64cart.c
@@ -88,7 +88,7 @@
 {
 	struct bio_vec bvec;
 	struct bvec_iter iter;
-	struct device *dev = bio->bi_disk->private_data;
+	struct device *dev = bio->bi_bdev->bd_disk->private_data;
 	u32 pos = bio->bi_iter.bi_sector << SECTOR_SHIFT;
 
 	bio_for_each_segment(bvec, bio, iter) {
@@ -137,7 +137,7 @@
 		return -ENOMEM;
 
 	disk->first_minor = 0;
-	disk->flags = GENHD_FL_NO_PART_SCAN;
+	disk->flags = GENHD_FL_NO_PART;
 	disk->fops = &n64cart_fops;
 	disk->private_data = &pdev->dev;
 	strcpy(disk->disk_name, "n64cart");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/nbd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/nbd.c
@@ -122,15 +122,21 @@
 	struct work_struct remove_work;
 
 	struct list_head list;
-	struct task_struct *task_recv;
 	struct task_struct *task_setup;
 
 	unsigned long flags;
+	pid_t pid; /* pid of nbd-client, if attached */
 
 	char *backend;
 };
 
 #define NBD_CMD_REQUEUED	1
+/*
+ * This flag will be set if nbd_queue_rq() succeed, and will be checked and
+ * cleared in completion. Both setting and clearing of the flag are protected
+ * by cmd->lock.
+ */
+#define NBD_CMD_INFLIGHT	2
 
 struct nbd_cmd {
 	struct nbd_device *nbd;
@@ -217,7 +223,7 @@
 	struct gendisk *disk = dev_to_disk(dev);
 	struct nbd_device *nbd = (struct nbd_device *)disk->private_data;
 
-	return sprintf(buf, "%d\n", task_pid_nr(nbd->task_recv));
+	return sprintf(buf, "%d\n", nbd->pid);
 }
 
 static const struct device_attribute pid_attr = {
@@ -254,7 +260,7 @@
 	mutex_lock(&nbd_index_mutex);
 	idr_remove(&nbd_index_idr, nbd->index);
 	mutex_unlock(&nbd_index_mutex);
-
+	destroy_workqueue(nbd->recv_workq);
 	kfree(nbd);
 }
 
@@ -326,10 +332,13 @@
 	if (blksize < 512 || blksize > PAGE_SIZE || !is_power_of_2(blksize))
 		return -EINVAL;
 
+	if (bytesize < 0)
+		return -EINVAL;
+
 	nbd->config->bytesize = bytesize;
 	nbd->config->blksize_bits = __ffs(blksize);
 
-	if (!nbd->task_recv)
+	if (!nbd->pid)
 		return 0;
 
 	if (nbd->config->flags & NBD_FLAG_SEND_TRIM) {
@@ -405,8 +414,14 @@
 	if (!mutex_trylock(&cmd->lock))
 		return BLK_EH_RESET_TIMER;
 
+	if (!test_bit(NBD_CMD_INFLIGHT, &cmd->flags)) {
+		mutex_unlock(&cmd->lock);
+		return BLK_EH_DONE;
+	}
+
 	if (!refcount_inc_not_zero(&nbd->config_refs)) {
 		cmd->status = BLK_STS_TIMEOUT;
+		__clear_bit(NBD_CMD_INFLIGHT, &cmd->flags);
 		mutex_unlock(&cmd->lock);
 		goto done;
 	}
@@ -475,6 +490,7 @@
 	dev_err_ratelimited(nbd_to_dev(nbd), "Connection timed out\n");
 	set_bit(NBD_RT_TIMEDOUT, &config->runtime_flags);
 	cmd->status = BLK_STS_IOERR;
+	__clear_bit(NBD_CMD_INFLIGHT, &cmd->flags);
 	mutex_unlock(&cmd->lock);
 	sock_shutdown(nbd);
 	nbd_config_put(nbd);
@@ -734,6 +750,12 @@
 	cmd = blk_mq_rq_to_pdu(req);
 
 	mutex_lock(&cmd->lock);
+	if (!test_bit(NBD_CMD_INFLIGHT, &cmd->flags)) {
+		dev_err(disk_to_dev(nbd->disk), "Suspicious reply %d (status %u flags %lu)",
+			tag, cmd->status, cmd->flags);
+		ret = -ENOENT;
+		goto out;
+	}
 	if (cmd->cmd_cookie != nbd_handle_to_cookie(handle)) {
 		dev_err(disk_to_dev(nbd->disk), "Double reply on req %p, cmd_cookie %u, handle cookie %u\n",
 			req, cmd->cmd_cookie, nbd_handle_to_cookie(handle));
@@ -815,8 +837,16 @@
 		}
 
 		rq = blk_mq_rq_from_pdu(cmd);
-		if (likely(!blk_should_fake_timeout(rq->q)))
-			blk_mq_complete_request(rq);
+		if (likely(!blk_should_fake_timeout(rq->q))) {
+			bool complete;
+
+			mutex_lock(&cmd->lock);
+			complete = __test_and_clear_bit(NBD_CMD_INFLIGHT,
+							&cmd->flags);
+			mutex_unlock(&cmd->lock);
+			if (complete)
+				blk_mq_complete_request(rq);
+		}
 	}
 	nbd_config_put(nbd);
 	atomic_dec(&config->recv_threads);
@@ -833,6 +863,10 @@
 		return true;
 
 	mutex_lock(&cmd->lock);
+	if (!__test_and_clear_bit(NBD_CMD_INFLIGHT, &cmd->flags)) {
+		mutex_unlock(&cmd->lock);
+		return true;
+	}
 	cmd->status = BLK_STS_IOERR;
 	mutex_unlock(&cmd->lock);
 
@@ -896,11 +930,15 @@
 	struct nbd_config *config = nbd->config;
 	if (!config->dead_conn_timeout)
 		return 0;
-	if (test_bit(NBD_RT_DISCONNECTED, &config->runtime_flags))
+
+	if (!wait_event_timeout(config->conn_wait,
+				test_bit(NBD_RT_DISCONNECTED,
+					 &config->runtime_flags) ||
+				atomic_read(&config->live_connections) > 0,
+				config->dead_conn_timeout))
 		return 0;
-	return wait_event_timeout(config->conn_wait,
-				  atomic_read(&config->live_connections) > 0,
-				  config->dead_conn_timeout) > 0;
+
+	return !test_bit(NBD_RT_DISCONNECTED, &config->runtime_flags);
 }
 
 static int nbd_handle_cmd(struct nbd_cmd *cmd, int index)
@@ -969,7 +1007,13 @@
 	 * returns EAGAIN can be retried on a different socket.
 	 */
 	ret = nbd_send_cmd(nbd, cmd, index);
-	if (ret == -EAGAIN) {
+	/*
+	 * Access to this flag is protected by cmd->lock, thus it's safe to set
+	 * the flag after nbd_send_cmd() succeed to send request to server.
+	 */
+	if (!ret)
+		__set_bit(NBD_CMD_INFLIGHT, &cmd->flags);
+	else if (ret == -EAGAIN) {
 		dev_err_ratelimited(disk_to_dev(nbd->disk),
 				    "Request send failed, requeueing\n");
 		nbd_mark_nsock_dead(nbd, nsock, 1);
@@ -1044,6 +1088,9 @@
 	struct nbd_sock *nsock;
 	int err;
 
+	/* Arg will be cast to int, check it to avoid overflow */
+	if (arg > INT_MAX)
+		return -EINVAL;
 	sock = nbd_get_socket(nbd, arg, &err);
 	if (!sock)
 		return err;
@@ -1163,11 +1210,11 @@
 	return -ENOSPC;
 }
 
-static void nbd_bdev_reset(struct block_device *bdev)
+static void nbd_bdev_reset(struct nbd_device *nbd)
 {
-	if (bdev->bd_openers > 1)
+	if (nbd->disk->part0->bd_openers > 1)
 		return;
-	set_capacity(bdev->bd_disk, 0);
+	set_capacity(nbd->disk, 0);
 }
 
 static void nbd_parse_flags(struct nbd_device *nbd)
@@ -1241,7 +1288,7 @@
 		if (test_and_clear_bit(NBD_RT_HAS_PID_FILE,
 				       &config->runtime_flags))
 			device_remove_file(disk_to_dev(nbd->disk), &pid_attr);
-		nbd->task_recv = NULL;
+		nbd->pid = 0;
 		if (test_and_clear_bit(NBD_RT_HAS_BACKEND_FILE,
 				       &config->runtime_flags)) {
 			device_remove_file(disk_to_dev(nbd->disk), &backend_attr);
@@ -1260,10 +1307,6 @@
 		kfree(nbd->config);
 		nbd->config = NULL;
 
-		if (nbd->recv_workq)
-			destroy_workqueue(nbd->recv_workq);
-		nbd->recv_workq = NULL;
-
 		nbd->tag_set.timeout = 0;
 		nbd->disk->queue->limits.discard_granularity = 0;
 		nbd->disk->queue->limits.discard_alignment = 0;
@@ -1282,7 +1325,7 @@
 	int num_connections = config->num_connections;
 	int error = 0, i;
 
-	if (nbd->task_recv)
+	if (nbd->pid)
 		return -EBUSY;
 	if (!config->socks)
 		return -EINVAL;
@@ -1292,16 +1335,8 @@
 		return -EINVAL;
 	}
 
-	nbd->recv_workq = alloc_workqueue("knbd%d-recv",
-					  WQ_MEM_RECLAIM | WQ_HIGHPRI |
-					  WQ_UNBOUND, 0, nbd->index);
-	if (!nbd->recv_workq) {
-		dev_err(disk_to_dev(nbd->disk), "Could not allocate knbd recv work queue.\n");
-		return -ENOMEM;
-	}
-
 	blk_mq_update_nr_hw_queues(&nbd->tag_set, config->num_connections);
-	nbd->task_recv = current;
+	nbd->pid = task_pid_nr(current);
 
 	nbd_parse_flags(nbd);
 
@@ -1345,7 +1380,7 @@
 	return nbd_set_size(nbd, config->bytesize, nbd_blksize(config));
 }
 
-static int nbd_start_device_ioctl(struct nbd_device *nbd, struct block_device *bdev)
+static int nbd_start_device_ioctl(struct nbd_device *nbd)
 {
 	struct nbd_config *config = nbd->config;
 	int ret;
@@ -1359,12 +1394,14 @@
 	mutex_unlock(&nbd->config_lock);
 	ret = wait_event_interruptible(config->recv_wq,
 					 atomic_read(&config->recv_threads) == 0);
-	if (ret)
+	if (ret) {
 		sock_shutdown(nbd);
-	flush_workqueue(nbd->recv_workq);
+		nbd_clear_que(nbd);
+	}
 
+	flush_workqueue(nbd->recv_workq);
 	mutex_lock(&nbd->config_lock);
-	nbd_bdev_reset(bdev);
+	nbd_bdev_reset(nbd);
 	/* user requested, ignore socket errors */
 	if (test_bit(NBD_RT_DISCONNECT_REQUESTED, &config->runtime_flags))
 		ret = 0;
@@ -1376,9 +1413,9 @@
 static void nbd_clear_sock_ioctl(struct nbd_device *nbd,
 				 struct block_device *bdev)
 {
-	sock_shutdown(nbd);
+	nbd_clear_sock(nbd);
 	__invalidate_device(bdev, true);
-	nbd_bdev_reset(bdev);
+	nbd_bdev_reset(nbd);
 	if (test_and_clear_bit(NBD_RT_HAS_CONFIG_REF,
 			       &nbd->config->runtime_flags))
 		nbd_config_put(nbd);
@@ -1424,7 +1461,7 @@
 		config->flags = arg;
 		return 0;
 	case NBD_DO_IT:
-		return nbd_start_device_ioctl(nbd, bdev);
+		return nbd_start_device_ioctl(nbd);
 	case NBD_CLEAR_QUE:
 		/*
 		 * This is for compatibility only.  The queue is always cleared
@@ -1475,15 +1512,20 @@
 {
 	struct nbd_config *config;
 
+	if (!try_module_get(THIS_MODULE))
+		return ERR_PTR(-ENODEV);
+
 	config = kzalloc(sizeof(struct nbd_config), GFP_NOFS);
-	if (!config)
-		return NULL;
+	if (!config) {
+		module_put(THIS_MODULE);
+		return ERR_PTR(-ENOMEM);
+	}
+
 	atomic_set(&config->recv_threads, 0);
 	init_waitqueue_head(&config->recv_wq);
 	init_waitqueue_head(&config->conn_wait);
 	config->blksize_bits = NBD_DEF_BLKSIZE_BITS;
 	atomic_set(&config->live_connections, 0);
-	try_module_get(THIS_MODULE);
 	return config;
 }
 
@@ -1510,12 +1552,13 @@
 			mutex_unlock(&nbd->config_lock);
 			goto out;
 		}
-		config = nbd->config = nbd_alloc_config();
-		if (!config) {
-			ret = -ENOMEM;
+		config = nbd_alloc_config();
+		if (IS_ERR(config)) {
+			ret = PTR_ERR(config);
 			mutex_unlock(&nbd->config_lock);
 			goto out;
 		}
+		nbd->config = config;
 		refcount_set(&nbd->config_refs, 1);
 		refcount_inc(&nbd->refs);
 		mutex_unlock(&nbd->config_lock);
@@ -1557,8 +1600,8 @@
 {
 	struct nbd_device *nbd = s->private;
 
-	if (nbd->task_recv)
-		seq_printf(s, "recv: %d\n", task_pid_nr(nbd->task_recv));
+	if (nbd->pid)
+		seq_printf(s, "recv: %d\n", nbd->pid);
 
 	return 0;
 }
@@ -1599,7 +1642,7 @@
 		return -EIO;
 
 	dir = debugfs_create_dir(nbd_name(nbd), nbd_dbg_dir);
-	if (!dir) {
+	if (IS_ERR(dir)) {
 		dev_err(nbd_to_dev(nbd), "Failed to create debugfs dir for '%s'\n",
 			nbd_name(nbd));
 		return -EIO;
@@ -1625,7 +1668,7 @@
 	struct dentry *dbg_dir;
 
 	dbg_dir = debugfs_create_dir("nbd", NULL);
-	if (!dbg_dir)
+	if (IS_ERR(dbg_dir))
 		return -EIO;
 
 	nbd_dbg_dir = dbg_dir;
@@ -1709,7 +1752,8 @@
 		if (err == -ENOSPC)
 			err = -EEXIST;
 	} else {
-		err = idr_alloc(&nbd_index_idr, nbd, 0, 0, GFP_KERNEL);
+		err = idr_alloc(&nbd_index_idr, nbd, 0,
+				(MINORMASK >> part_shift) + 1, GFP_KERNEL);
 		if (err >= 0)
 			index = err;
 	}
@@ -1725,6 +1769,15 @@
 	}
 	nbd->disk = disk;
 
+	nbd->recv_workq = alloc_workqueue("nbd%d-recv",
+					  WQ_MEM_RECLAIM | WQ_HIGHPRI |
+					  WQ_UNBOUND, 0, nbd->index);
+	if (!nbd->recv_workq) {
+		dev_err(disk_to_dev(nbd->disk), "Could not allocate knbd recv work queue.\n");
+		err = -ENOMEM;
+		goto out_err_disk;
+	}
+
 	/*
 	 * Tell the block layer that we are not a rotational device
 	 */
@@ -1747,22 +1800,14 @@
 	refcount_set(&nbd->refs, 0);
 	INIT_LIST_HEAD(&nbd->list);
 	disk->major = NBD_MAJOR;
-
-	/* Too big first_minor can cause duplicate creation of
-	 * sysfs files/links, since first_minor will be truncated to
-	 * byte in __device_add_disk().
-	 */
 	disk->first_minor = index << part_shift;
-	if (disk->first_minor > 0xff) {
-		err = -EINVAL;
-		goto out_free_idr;
-	}
-
 	disk->minors = 1 << part_shift;
 	disk->fops = &nbd_fops;
 	disk->private_data = nbd;
 	sprintf(disk->disk_name, "nbd%d", index);
-	add_disk(disk);
+	err = add_disk(disk);
+	if (err)
+		goto out_free_work;
 
 	/*
 	 * Now publish the device.
@@ -1771,6 +1816,10 @@
 	nbd_total_devices++;
 	return nbd;
 
+out_free_work:
+	destroy_workqueue(nbd->recv_workq);
+out_err_disk:
+	blk_cleanup_disk(disk);
 out_free_idr:
 	mutex_lock(&nbd_index_mutex);
 	idr_remove(&nbd_index_idr, index);
@@ -1856,8 +1905,19 @@
 	if (!netlink_capable(skb, CAP_SYS_ADMIN))
 		return -EPERM;
 
-	if (info->attrs[NBD_ATTR_INDEX])
+	if (info->attrs[NBD_ATTR_INDEX]) {
 		index = nla_get_u32(info->attrs[NBD_ATTR_INDEX]);
+
+		/*
+		 * Too big first_minor can cause duplicate creation of
+		 * sysfs files/links, since index << part_shift might overflow, or
+		 * MKDEV() expect that the max bits of first_minor is 20.
+		 */
+		if (index < 0 || index > MINORMASK >> part_shift) {
+			printk(KERN_ERR "nbd: illegal input index %d\n", index);
+			return -EINVAL;
+		}
+	}
 	if (!info->attrs[NBD_ATTR_SOCKETS]) {
 		printk(KERN_ERR "nbd: must specify at least one socket\n");
 		return -EINVAL;
@@ -1907,13 +1967,14 @@
 		nbd_put(nbd);
 		return -EINVAL;
 	}
-	config = nbd->config = nbd_alloc_config();
-	if (!nbd->config) {
+	config = nbd_alloc_config();
+	if (IS_ERR(config)) {
 		mutex_unlock(&nbd->config_lock);
 		nbd_put(nbd);
 		printk(KERN_ERR "nbd: couldn't allocate config\n");
-		return -ENOMEM;
+		return PTR_ERR(config);
 	}
+	nbd->config = config;
 	refcount_set(&nbd->config_refs, 1);
 	set_bit(NBD_RT_BOUND, &config->runtime_flags);
 
@@ -2023,16 +2084,15 @@
 	mutex_lock(&nbd->config_lock);
 	nbd_disconnect(nbd);
 	sock_shutdown(nbd);
+	wake_up(&nbd->config->conn_wait);
 	/*
-	 * Make sure recv thread has finished, so it does not drop the last
-	 * config ref and try to destroy the workqueue from inside the work
-	 * queue. And this also ensure that we can safely call nbd_clear_que()
+	 * Make sure recv thread has finished, we can safely call nbd_clear_que()
 	 * to cancel the inflight I/Os.
 	 */
-	if (nbd->recv_workq)
-		flush_workqueue(nbd->recv_workq);
+	flush_workqueue(nbd->recv_workq);
 	nbd_clear_que(nbd);
 	nbd->task_setup = NULL;
+	clear_bit(NBD_RT_BOUND, &nbd->config->runtime_flags);
 	mutex_unlock(&nbd->config_lock);
 
 	if (test_and_clear_bit(NBD_RT_HAS_CONFIG_REF,
@@ -2135,7 +2195,7 @@
 	mutex_lock(&nbd->config_lock);
 	config = nbd->config;
 	if (!test_bit(NBD_RT_BOUND, &config->runtime_flags) ||
-	    !nbd->task_recv) {
+	    !nbd->pid) {
 		dev_err(nbd_to_dev(nbd),
 			"not configured, cannot reconfigure\n");
 		ret = -EINVAL;
@@ -2322,6 +2382,12 @@
 	}
 
 	dev_list = nla_nest_start_noflag(reply, NBD_ATTR_DEVICE_LIST);
+	if (!dev_list) {
+		nlmsg_free(reply);
+		ret = -EMSGSIZE;
+		goto out;
+	}
+
 	if (index == -1) {
 		ret = idr_for_each(&nbd_index_idr, &status_cb, reply);
 		if (ret) {
@@ -2473,6 +2539,12 @@
 	struct nbd_device *nbd;
 	LIST_HEAD(del_list);
 
+	/*
+	 * Unregister netlink interface prior to waiting
+	 * for the completion of netlink commands.
+	 */
+	genl_unregister_family(&nbd_genl_family);
+
 	nbd_dbg_close();
 
 	mutex_lock(&nbd_index_mutex);
@@ -2482,6 +2554,9 @@
 	while (!list_empty(&del_list)) {
 		nbd = list_first_entry(&del_list, struct nbd_device, list);
 		list_del_init(&nbd->list);
+		if (refcount_read(&nbd->config_refs))
+			printk(KERN_ERR "nbd: possibly leaking nbd_config (ref %d)\n",
+					refcount_read(&nbd->config_refs));
 		if (refcount_read(&nbd->refs) != 1)
 			printk(KERN_ERR "nbd: possibly leaking a device\n");
 		nbd_put(nbd);
@@ -2491,7 +2566,6 @@
 	destroy_workqueue(nbd_del_wq);
 
 	idr_destroy(&nbd_index_idr);
-	genl_unregister_family(&nbd_genl_family);
 	unregister_blkdev(NBD_MAJOR, "nbd");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/null_blk/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/null_blk/main.c
@@ -1314,8 +1314,7 @@
 	case NULL_IRQ_SOFTIRQ:
 		switch (cmd->nq->dev->queue_mode) {
 		case NULL_Q_MQ:
-			if (likely(!blk_should_fake_timeout(cmd->rq->q)))
-				blk_mq_complete_request(cmd->rq);
+			blk_mq_complete_request(cmd->rq);
 			break;
 		case NULL_Q_BIO:
 			/*
@@ -1491,7 +1490,8 @@
 	cmd->rq = bd->rq;
 	cmd->error = BLK_STS_OK;
 	cmd->nq = nq;
-	cmd->fake_timeout = should_timeout_request(bd->rq);
+	cmd->fake_timeout = should_timeout_request(bd->rq) ||
+		blk_should_fake_timeout(bd->rq->q);
 
 	blk_mq_start_request(bd->rq);
 
@@ -1744,8 +1744,13 @@
 
 static int null_validate_conf(struct nullb_device *dev)
 {
-	dev->blocksize = round_down(dev->blocksize, 512);
-	dev->blocksize = clamp_t(unsigned int, dev->blocksize, 512, 4096);
+	if (dev->queue_mode == NULL_Q_RQ) {
+		pr_err("legacy IO path is no longer available\n");
+		return -EINVAL;
+	}
+
+	if (blk_validate_block_size(dev->blocksize))
+		return -EINVAL;
 
 	if (dev->queue_mode == NULL_Q_MQ && dev->use_per_node_hctx) {
 		if (dev->submit_queues != nr_online_nodes)
@@ -1884,17 +1889,19 @@
 	blk_queue_flag_clear(QUEUE_FLAG_ADD_RANDOM, nullb->q);
 
 	mutex_lock(&lock);
-	nullb->index = ida_simple_get(&nullb_indexes, 0, 0, GFP_KERNEL);
-	dev->index = nullb->index;
+	rv = ida_simple_get(&nullb_indexes, 0, 0, GFP_KERNEL);
+	if (rv < 0) {
+		mutex_unlock(&lock);
+		goto out_cleanup_zone;
+	}
+	nullb->index = rv;
+	dev->index = rv;
 	mutex_unlock(&lock);
 
 	blk_queue_logical_block_size(nullb->q, dev->blocksize);
 	blk_queue_physical_block_size(nullb->q, dev->blocksize);
-	if (!dev->max_sectors)
-		dev->max_sectors = queue_max_hw_sectors(nullb->q);
-	dev->max_sectors = min_t(unsigned int, dev->max_sectors,
-				 BLK_DEF_MAX_SECTORS);
-	blk_queue_max_hw_sectors(nullb->q, dev->max_sectors);
+	if (dev->max_sectors)
+		blk_queue_max_hw_sectors(nullb->q, dev->max_sectors);
 
 	if (dev->virt_boundary)
 		blk_queue_virt_boundary(nullb->q, PAGE_SIZE - 1);
@@ -1905,13 +1912,16 @@
 
 	rv = null_gendisk_register(nullb);
 	if (rv)
-		goto out_cleanup_zone;
+		goto out_ida_free;
 
 	mutex_lock(&lock);
 	list_add_tail(&nullb->list, &nullb_list);
 	mutex_unlock(&lock);
 
 	return 0;
+
+out_ida_free:
+	ida_free(&nullb_indexes, nullb->index);
 out_cleanup_zone:
 	null_free_zoned_dev(dev);
 out_cleanup_disk:
@@ -1941,12 +1951,6 @@
 		g_bs = PAGE_SIZE;
 	}
 
-	if (g_max_sectors > BLK_DEF_MAX_SECTORS) {
-		pr_warn("invalid max sectors\n");
-		pr_warn("defaults max sectors to %u\n", BLK_DEF_MAX_SECTORS);
-		g_max_sectors = BLK_DEF_MAX_SECTORS;
-	}
-
 	if (g_home_node != NUMA_NO_NODE && g_home_node >= nr_online_nodes) {
 		pr_err("invalid home_node value\n");
 		g_home_node = NUMA_NO_NODE;
@@ -2041,10 +2045,13 @@
 
 	if (g_queue_mode == NULL_Q_MQ && shared_tags)
 		blk_mq_free_tag_set(&tag_set);
+
+	mutex_destroy(&lock);
 }
 
 module_init(null_init);
 module_exit(null_exit);
 
 MODULE_AUTHOR("Jens Axboe <axboe@kernel.dk>");
+MODULE_DESCRIPTION("multi queue aware block test driver");
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/null_blk/zoned.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/null_blk/zoned.c
@@ -80,6 +80,17 @@
 		return -EINVAL;
 	}
 
+	/*
+	 * If a smaller zone capacity was requested, do not allow a smaller last
+	 * zone at the same time as such zone configuration does not correspond
+	 * to any real zoned device.
+	 */
+	if (dev->zone_capacity != dev->zone_size &&
+	    dev->size & (dev->zone_size - 1)) {
+		pr_err("A smaller last zone is not allowed with zone capacity smaller than zone size.\n");
+		return -EINVAL;
+	}
+
 	zone_capacity_sects = mb_to_sects(dev->zone_capacity);
 	dev_capacity_sects = mb_to_sects(dev->size);
 	dev->zone_size_sects = mb_to_sects(dev->zone_size);
@@ -109,7 +120,7 @@
 	if (dev->zone_max_active && dev->zone_max_open > dev->zone_max_active) {
 		dev->zone_max_open = dev->zone_max_active;
 		pr_info("changed the maximum number of open zones to %u\n",
-			dev->nr_zones);
+			dev->zone_max_open);
 	} else if (dev->zone_max_open >= dev->nr_zones - dev->zone_nr_conv) {
 		dev->zone_max_open = 0;
 		pr_info("zone_max_open limit disabled, limit >= zone count\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/paride/pcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/paride/pcd.c
@@ -183,8 +183,6 @@
 static int pcd_packet(struct cdrom_device_info *cdi,
 		      struct packet_command *cgc);
 
-static int pcd_detect(void);
-static void pcd_probe_capabilities(void);
 static void do_pcd_read_drq(void);
 static blk_status_t pcd_queue_rq(struct blk_mq_hw_ctx *hctx,
 				 const struct blk_mq_queue_data *bd);
@@ -302,53 +300,6 @@
 	.queue_rq	= pcd_queue_rq,
 };
 
-static void pcd_init_units(void)
-{
-	struct pcd_unit *cd;
-	int unit;
-
-	pcd_drive_count = 0;
-	for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-		struct gendisk *disk;
-
-		if (blk_mq_alloc_sq_tag_set(&cd->tag_set, &pcd_mq_ops, 1,
-				BLK_MQ_F_SHOULD_MERGE))
-			continue;
-
-		disk = blk_mq_alloc_disk(&cd->tag_set, cd);
-		if (IS_ERR(disk)) {
-			blk_mq_free_tag_set(&cd->tag_set);
-			continue;
-		}
-
-		INIT_LIST_HEAD(&cd->rq_list);
-		blk_queue_bounce_limit(disk->queue, BLK_BOUNCE_HIGH);
-		cd->disk = disk;
-		cd->pi = &cd->pia;
-		cd->present = 0;
-		cd->last_sense = 0;
-		cd->changed = 1;
-		cd->drive = (*drives[unit])[D_SLV];
-		if ((*drives[unit])[D_PRT])
-			pcd_drive_count++;
-
-		cd->name = &cd->info.name[0];
-		snprintf(cd->name, sizeof(cd->info.name), "%s%d", name, unit);
-		cd->info.ops = &pcd_dops;
-		cd->info.handle = cd;
-		cd->info.speed = 0;
-		cd->info.capacity = 1;
-		cd->info.mask = 0;
-		disk->major = major;
-		disk->first_minor = unit;
-		disk->minors = 1;
-		strcpy(disk->disk_name, cd->name);	/* umm... */
-		disk->fops = &pcd_bdops;
-		disk->flags = GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE;
-		disk->events = DISK_EVENT_MEDIA_CHANGE;
-	}
-}
-
 static int pcd_open(struct cdrom_device_info *cdi, int purpose)
 {
 	struct pcd_unit *cd = cdi->handle;
@@ -630,10 +581,11 @@
 	return CDS_DISC_OK;
 }
 
-static int pcd_identify(struct pcd_unit *cd, char *id)
+static int pcd_identify(struct pcd_unit *cd)
 {
-	int k, s;
 	char id_cmd[12] = { 0x12, 0, 0, 0, 36, 0, 0, 0, 0, 0, 0, 0 };
+	char id[18];
+	int k, s;
 
 	pcd_bufblk = -1;
 
@@ -661,108 +613,47 @@
 }
 
 /*
- * returns  0, with id set if drive is detected
- *	    -1, if drive detection failed
+ * returns 0, with id set if drive is detected, otherwise an error code.
  */
-static int pcd_probe(struct pcd_unit *cd, int ms, char *id)
+static int pcd_probe(struct pcd_unit *cd, int ms)
 {
 	if (ms == -1) {
 		for (cd->drive = 0; cd->drive <= 1; cd->drive++)
-			if (!pcd_reset(cd) && !pcd_identify(cd, id))
+			if (!pcd_reset(cd) && !pcd_identify(cd))
 				return 0;
 	} else {
 		cd->drive = ms;
-		if (!pcd_reset(cd) && !pcd_identify(cd, id))
+		if (!pcd_reset(cd) && !pcd_identify(cd))
 			return 0;
 	}
-	return -1;
+	return -ENODEV;
 }
 
-static void pcd_probe_capabilities(void)
+static int pcd_probe_capabilities(struct pcd_unit *cd)
 {
-	int unit, r;
-	char buffer[32];
 	char cmd[12] = { 0x5a, 1 << 3, 0x2a, 0, 0, 0, 0, 18, 0, 0, 0, 0 };
-	struct pcd_unit *cd;
-
-	for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-		if (!cd->present)
-			continue;
-		r = pcd_atapi(cd, cmd, 18, buffer, "mode sense capabilities");
-		if (r)
-			continue;
-		/* we should now have the cap page */
-		if ((buffer[11] & 1) == 0)
-			cd->info.mask |= CDC_CD_R;
-		if ((buffer[11] & 2) == 0)
-			cd->info.mask |= CDC_CD_RW;
-		if ((buffer[12] & 1) == 0)
-			cd->info.mask |= CDC_PLAY_AUDIO;
-		if ((buffer[14] & 1) == 0)
-			cd->info.mask |= CDC_LOCK;
-		if ((buffer[14] & 8) == 0)
-			cd->info.mask |= CDC_OPEN_TRAY;
-		if ((buffer[14] >> 6) == 0)
-			cd->info.mask |= CDC_CLOSE_TRAY;
-	}
-}
-
-static int pcd_detect(void)
-{
-	char id[18];
-	int k, unit;
-	struct pcd_unit *cd;
-
-	printk("%s: %s version %s, major %d, nice %d\n",
-	       name, name, PCD_VERSION, major, nice);
+	char buffer[32];
+	int ret;
 
-	par_drv = pi_register_driver(name);
-	if (!par_drv) {
-		pr_err("failed to register %s driver\n", name);
-		return -1;
-	}
+	ret = pcd_atapi(cd, cmd, 18, buffer, "mode sense capabilities");
+	if (ret)
+		return ret;
+
+	/* we should now have the cap page */
+	if ((buffer[11] & 1) == 0)
+		cd->info.mask |= CDC_CD_R;
+	if ((buffer[11] & 2) == 0)
+		cd->info.mask |= CDC_CD_RW;
+	if ((buffer[12] & 1) == 0)
+		cd->info.mask |= CDC_PLAY_AUDIO;
+	if ((buffer[14] & 1) == 0)
+		cd->info.mask |= CDC_LOCK;
+	if ((buffer[14] & 8) == 0)
+		cd->info.mask |= CDC_OPEN_TRAY;
+	if ((buffer[14] >> 6) == 0)
+		cd->info.mask |= CDC_CLOSE_TRAY;
 
-	k = 0;
-	if (pcd_drive_count == 0) { /* nothing spec'd - so autoprobe for 1 */
-		cd = pcd;
-		if (cd->disk && pi_init(cd->pi, 1, -1, -1, -1, -1, -1,
-			    pcd_buffer, PI_PCD, verbose, cd->name)) {
-			if (!pcd_probe(cd, -1, id)) {
-				cd->present = 1;
-				k++;
-			} else
-				pi_release(cd->pi);
-		}
-	} else {
-		for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-			int *conf = *drives[unit];
-			if (!conf[D_PRT])
-				continue;
-			if (!cd->disk)
-				continue;
-			if (!pi_init(cd->pi, 0, conf[D_PRT], conf[D_MOD],
-				     conf[D_UNI], conf[D_PRO], conf[D_DLY],
-				     pcd_buffer, PI_PCD, verbose, cd->name)) 
-				continue;
-			if (!pcd_probe(cd, conf[D_SLV], id)) {
-				cd->present = 1;
-				k++;
-			} else
-				pi_release(cd->pi);
-		}
-	}
-	if (k)
-		return 0;
-
-	printk("%s: No CD-ROM drive found\n", name);
-	for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-		if (!cd->disk)
-			continue;
-		blk_cleanup_disk(cd->disk);
-		blk_mq_free_tag_set(&cd->tag_set);
-	}
-	pi_unregister_driver(par_drv);
-	return -1;
+	return 0;
 }
 
 /* I/O request processing */
@@ -999,43 +890,124 @@
 	return 0;
 }
 
+static int pcd_init_unit(struct pcd_unit *cd, bool autoprobe, int port,
+		int mode, int unit, int protocol, int delay, int ms)
+{
+	struct gendisk *disk;
+	int ret;
+
+	ret = blk_mq_alloc_sq_tag_set(&cd->tag_set, &pcd_mq_ops, 1,
+				      BLK_MQ_F_SHOULD_MERGE);
+	if (ret)
+		return ret;
+
+	disk = blk_mq_alloc_disk(&cd->tag_set, cd);
+	if (IS_ERR(disk)) {
+		ret = PTR_ERR(disk);
+		goto out_free_tag_set;
+	}
+
+	INIT_LIST_HEAD(&cd->rq_list);
+	blk_queue_bounce_limit(disk->queue, BLK_BOUNCE_HIGH);
+	cd->disk = disk;
+	cd->pi = &cd->pia;
+	cd->present = 0;
+	cd->last_sense = 0;
+	cd->changed = 1;
+	cd->drive = (*drives[cd - pcd])[D_SLV];
+
+	cd->name = &cd->info.name[0];
+	snprintf(cd->name, sizeof(cd->info.name), "%s%d", name, unit);
+	cd->info.ops = &pcd_dops;
+	cd->info.handle = cd;
+	cd->info.speed = 0;
+	cd->info.capacity = 1;
+	cd->info.mask = 0;
+	disk->major = major;
+	disk->first_minor = unit;
+	disk->minors = 1;
+	strcpy(disk->disk_name, cd->name);	/* umm... */
+	disk->fops = &pcd_bdops;
+	disk->events = DISK_EVENT_MEDIA_CHANGE;
+	disk->event_flags = DISK_EVENT_FLAG_BLOCK_ON_EXCL_WRITE;
+
+	if (!pi_init(cd->pi, autoprobe, port, mode, unit, protocol, delay,
+			pcd_buffer, PI_PCD, verbose, cd->name)) {
+		ret = -ENODEV;
+		goto out_free_disk;
+	}
+	ret = pcd_probe(cd, ms);
+	if (ret)
+		goto out_pi_release;
+
+	cd->present = 1;
+	pcd_probe_capabilities(cd);
+	register_cdrom(cd->disk, &cd->info);
+	add_disk(cd->disk);
+	return 0;
+
+out_pi_release:
+	pi_release(cd->pi);
+out_free_disk:
+	blk_cleanup_disk(cd->disk);
+out_free_tag_set:
+	blk_mq_free_tag_set(&cd->tag_set);
+	return ret;
+}
+
 static int __init pcd_init(void)
 {
-	struct pcd_unit *cd;
-	int unit;
+	int found = 0, unit;
 
 	if (disable)
 		return -EINVAL;
 
-	pcd_init_units();
+	if (register_blkdev(major, name))
+		return -EBUSY;
 
-	if (pcd_detect())
-		return -ENODEV;
+	pr_info("%s: %s version %s, major %d, nice %d\n",
+		name, name, PCD_VERSION, major, nice);
 
-	/* get the atapi capabilities page */
-	pcd_probe_capabilities();
+	par_drv = pi_register_driver(name);
+	if (!par_drv) {
+		pr_err("failed to register %s driver\n", name);
+		goto out_unregister_blkdev;
+	}
 
-	if (register_blkdev(major, name)) {
-		for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-			if (!cd->disk)
-				continue;
+	for (unit = 0; unit < PCD_UNITS; unit++) {
+		if ((*drives[unit])[D_PRT])
+			pcd_drive_count++;
+	}
 
-			blk_cleanup_queue(cd->disk->queue);
-			blk_mq_free_tag_set(&cd->tag_set);
-			put_disk(cd->disk);
+	if (pcd_drive_count == 0) { /* nothing spec'd - so autoprobe for 1 */
+		if (!pcd_init_unit(pcd, 1, -1, -1, -1, -1, -1, -1))
+			found++;
+	} else {
+		for (unit = 0; unit < PCD_UNITS; unit++) {
+			struct pcd_unit *cd = &pcd[unit];
+			int *conf = *drives[unit];
+
+			if (!conf[D_PRT])
+				continue;
+			if (!pcd_init_unit(cd, 0, conf[D_PRT], conf[D_MOD],
+					conf[D_UNI], conf[D_PRO], conf[D_DLY],
+					conf[D_SLV]))
+				found++;
 		}
-		return -EBUSY;
 	}
 
-	for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-		if (cd->present) {
-			register_cdrom(cd->disk, &cd->info);
-			cd->disk->private_data = cd;
-			add_disk(cd->disk);
-		}
+	if (!found) {
+		pr_info("%s: No CD-ROM drive found\n", name);
+		goto out_unregister_pi_driver;
 	}
 
 	return 0;
+
+out_unregister_pi_driver:
+	pi_unregister_driver(par_drv);
+out_unregister_blkdev:
+	unregister_blkdev(major, name);
+	return -ENODEV;
 }
 
 static void __exit pcd_exit(void)
@@ -1044,20 +1016,18 @@
 	int unit;
 
 	for (unit = 0, cd = pcd; unit < PCD_UNITS; unit++, cd++) {
-		if (!cd->disk)
+		if (!cd->present)
 			continue;
 
-		if (cd->present) {
-			del_gendisk(cd->disk);
-			pi_release(cd->pi);
-			unregister_cdrom(&cd->info);
-		}
-		blk_cleanup_queue(cd->disk->queue);
+		del_gendisk(cd->disk);
+		pi_release(cd->pi);
+		unregister_cdrom(&cd->info);
+		blk_cleanup_disk(cd->disk);
+
 		blk_mq_free_tag_set(&cd->tag_set);
-		put_disk(cd->disk);
 	}
-	unregister_blkdev(major, name);
 	pi_unregister_driver(par_drv);
+	unregister_blkdev(major, name);
 }
 
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/pktcdvd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/pktcdvd.c
@@ -2407,6 +2407,8 @@
 	struct bio *split;
 
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
 	pd = bio->bi_bdev->bd_disk->queue->queuedata;
 	if (!pd) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/ps3vram.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/ps3vram.c
@@ -587,6 +587,8 @@
 	dev_dbg(&dev->core, "%s\n", __func__);
 
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
 	spin_lock_irq(&priv->lock);
 	busy = !bio_list_empty(&priv->list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/rbd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/rbd.c
@@ -362,7 +362,7 @@
 enum rbd_lock_state {
 	RBD_LOCK_STATE_UNLOCKED,
 	RBD_LOCK_STATE_LOCKED,
-	RBD_LOCK_STATE_RELEASING,
+	RBD_LOCK_STATE_QUIESCING,
 };
 
 /* WatchNotify::ClientId */
@@ -422,7 +422,7 @@
 	struct list_head	running_list;
 	struct completion	acquire_wait;
 	int			acquire_err;
-	struct completion	releasing_wait;
+	struct completion	quiescing_wait;
 
 	spinlock_t		object_map_lock;
 	u8			*object_map;
@@ -525,7 +525,7 @@
 	lockdep_assert_held(&rbd_dev->lock_rwsem);
 
 	return rbd_dev->lock_state == RBD_LOCK_STATE_LOCKED ||
-	       rbd_dev->lock_state == RBD_LOCK_STATE_RELEASING;
+	       rbd_dev->lock_state == RBD_LOCK_STATE_QUIESCING;
 }
 
 static bool rbd_is_lock_owner(struct rbd_device *rbd_dev)
@@ -632,9 +632,8 @@
 static void rbd_dev_remove_parent(struct rbd_device *rbd_dev);
 
 static int rbd_dev_refresh(struct rbd_device *rbd_dev);
-static int rbd_dev_v2_header_onetime(struct rbd_device *rbd_dev);
-static int rbd_dev_header_info(struct rbd_device *rbd_dev);
-static int rbd_dev_v2_parent_info(struct rbd_device *rbd_dev);
+static int rbd_dev_v2_header_onetime(struct rbd_device *rbd_dev,
+				     struct rbd_image_header *header);
 static const char *rbd_dev_v2_snap_name(struct rbd_device *rbd_dev,
 					u64 snap_id);
 static int _rbd_dev_v2_snap_size(struct rbd_device *rbd_dev, u64 snap_id,
@@ -996,15 +995,24 @@
 	RCU_INIT_POINTER(rbd_dev->layout.pool_ns, NULL);
 }
 
+static void rbd_image_header_cleanup(struct rbd_image_header *header)
+{
+	kfree(header->object_prefix);
+	ceph_put_snap_context(header->snapc);
+	kfree(header->snap_sizes);
+	kfree(header->snap_names);
+
+	memset(header, 0, sizeof(*header));
+}
+
 /*
  * Fill an rbd image header with information from the given format 1
  * on-disk header.
  */
-static int rbd_header_from_disk(struct rbd_device *rbd_dev,
-				 struct rbd_image_header_ondisk *ondisk)
+static int rbd_header_from_disk(struct rbd_image_header *header,
+				struct rbd_image_header_ondisk *ondisk,
+				bool first_time)
 {
-	struct rbd_image_header *header = &rbd_dev->header;
-	bool first_time = header->object_prefix == NULL;
 	struct ceph_snap_context *snapc;
 	char *object_prefix = NULL;
 	char *snap_names = NULL;
@@ -1071,11 +1079,6 @@
 	if (first_time) {
 		header->object_prefix = object_prefix;
 		header->obj_order = ondisk->options.order;
-		rbd_init_layout(rbd_dev);
-	} else {
-		ceph_put_snap_context(header->snapc);
-		kfree(header->snap_names);
-		kfree(header->snap_sizes);
 	}
 
 	/* The remaining fields always get updated (when we refresh) */
@@ -1335,14 +1338,30 @@
 /*
  * Must be called after rbd_obj_calc_img_extents().
  */
-static bool rbd_obj_copyup_enabled(struct rbd_obj_request *obj_req)
+static void rbd_obj_set_copyup_enabled(struct rbd_obj_request *obj_req)
 {
-	if (!obj_req->num_img_extents ||
-	    (rbd_obj_is_entire(obj_req) &&
-	     !obj_req->img_request->snapc->num_snaps))
-		return false;
+	rbd_assert(obj_req->img_request->snapc);
 
-	return true;
+	if (obj_req->img_request->op_type == OBJ_OP_DISCARD) {
+		dout("%s %p objno %llu discard\n", __func__, obj_req,
+		     obj_req->ex.oe_objno);
+		return;
+	}
+
+	if (!obj_req->num_img_extents) {
+		dout("%s %p objno %llu not overlapping\n", __func__, obj_req,
+		     obj_req->ex.oe_objno);
+		return;
+	}
+
+	if (rbd_obj_is_entire(obj_req) &&
+	    !obj_req->img_request->snapc->num_snaps) {
+		dout("%s %p objno %llu entire\n", __func__, obj_req,
+		     obj_req->ex.oe_objno);
+		return;
+	}
+
+	obj_req->flags |= RBD_OBJ_FLAG_COPYUP_ENABLED;
 }
 
 static u64 rbd_obj_img_extents_bytes(struct rbd_obj_request *obj_req)
@@ -1443,6 +1462,7 @@
 static struct ceph_osd_request *
 rbd_obj_add_osd_request(struct rbd_obj_request *obj_req, int num_ops)
 {
+	rbd_assert(obj_req->img_request->snapc);
 	return __rbd_obj_add_osd_request(obj_req, obj_req->img_request->snapc,
 					 num_ops);
 }
@@ -1579,15 +1599,18 @@
 	mutex_init(&img_request->state_mutex);
 }
 
+/*
+ * Only snap_id is captured here, for reads.  For writes, snapshot
+ * context is captured in rbd_img_object_requests() after exclusive
+ * lock is ensured to be held.
+ */
 static void rbd_img_capture_header(struct rbd_img_request *img_req)
 {
 	struct rbd_device *rbd_dev = img_req->rbd_dev;
 
 	lockdep_assert_held(&rbd_dev->header_rwsem);
 
-	if (rbd_img_is_write(img_req))
-		img_req->snapc = ceph_get_snap_context(rbd_dev->header.snapc);
-	else
+	if (!rbd_img_is_write(img_req))
 		img_req->snap_id = rbd_dev->spec->snap_id;
 
 	if (rbd_dev_parent_get(rbd_dev))
@@ -2234,9 +2257,6 @@
 	if (ret)
 		return ret;
 
-	if (rbd_obj_copyup_enabled(obj_req))
-		obj_req->flags |= RBD_OBJ_FLAG_COPYUP_ENABLED;
-
 	obj_req->write_state = RBD_OBJ_WRITE_START;
 	return 0;
 }
@@ -2342,8 +2362,6 @@
 	if (ret)
 		return ret;
 
-	if (rbd_obj_copyup_enabled(obj_req))
-		obj_req->flags |= RBD_OBJ_FLAG_COPYUP_ENABLED;
 	if (!obj_req->num_img_extents) {
 		obj_req->flags |= RBD_OBJ_FLAG_NOOP_FOR_NONEXISTENT;
 		if (rbd_obj_is_entire(obj_req))
@@ -3288,6 +3306,7 @@
 	case RBD_OBJ_WRITE_START:
 		rbd_assert(!*result);
 
+		rbd_obj_set_copyup_enabled(obj_req);
 		if (rbd_obj_write_is_noop(obj_req))
 			return true;
 
@@ -3435,17 +3454,19 @@
 static void rbd_lock_del_request(struct rbd_img_request *img_req)
 {
 	struct rbd_device *rbd_dev = img_req->rbd_dev;
-	bool need_wakeup;
+	bool need_wakeup = false;
 
 	lockdep_assert_held(&rbd_dev->lock_rwsem);
 	spin_lock(&rbd_dev->lock_lists_lock);
-	rbd_assert(!list_empty(&img_req->lock_item));
-	list_del_init(&img_req->lock_item);
-	need_wakeup = (rbd_dev->lock_state == RBD_LOCK_STATE_RELEASING &&
-		       list_empty(&rbd_dev->running_list));
+	if (!list_empty(&img_req->lock_item)) {
+		rbd_assert(!list_empty(&rbd_dev->running_list));
+		list_del_init(&img_req->lock_item);
+		need_wakeup = (rbd_dev->lock_state == RBD_LOCK_STATE_QUIESCING &&
+			       list_empty(&rbd_dev->running_list));
+	}
 	spin_unlock(&rbd_dev->lock_lists_lock);
 	if (need_wakeup)
-		complete(&rbd_dev->releasing_wait);
+		complete(&rbd_dev->quiescing_wait);
 }
 
 static int rbd_img_exclusive_lock(struct rbd_img_request *img_req)
@@ -3458,11 +3479,6 @@
 	if (rbd_lock_add_request(img_req))
 		return 1;
 
-	if (rbd_dev->opts->exclusive) {
-		WARN_ON(1); /* lock got released? */
-		return -EROFS;
-	}
-
 	/*
 	 * Note the use of mod_delayed_work() in rbd_acquire_lock()
 	 * and cancel_delayed_work() in wake_lock_waiters().
@@ -3474,9 +3490,19 @@
 
 static void rbd_img_object_requests(struct rbd_img_request *img_req)
 {
+	struct rbd_device *rbd_dev = img_req->rbd_dev;
 	struct rbd_obj_request *obj_req;
 
 	rbd_assert(!img_req->pending.result && !img_req->pending.num_pending);
+	rbd_assert(!need_exclusive_lock(img_req) ||
+		   __rbd_is_lock_owner(rbd_dev));
+
+	if (rbd_img_is_write(img_req)) {
+		rbd_assert(!img_req->snapc);
+		down_read(&rbd_dev->header_rwsem);
+		img_req->snapc = ceph_get_snap_context(rbd_dev->header.snapc);
+		up_read(&rbd_dev->header_rwsem);
+	}
 
 	for_each_obj_request(img_req, obj_req) {
 		int result = 0;
@@ -3494,7 +3520,6 @@
 
 static bool rbd_img_advance(struct rbd_img_request *img_req, int *result)
 {
-	struct rbd_device *rbd_dev = img_req->rbd_dev;
 	int ret;
 
 again:
@@ -3515,9 +3540,6 @@
 		if (*result)
 			return true;
 
-		rbd_assert(!need_exclusive_lock(img_req) ||
-			   __rbd_is_lock_owner(rbd_dev));
-
 		rbd_img_object_requests(img_req);
 		if (!img_req->pending.num_pending) {
 			*result = img_req->pending.result;
@@ -3655,7 +3677,7 @@
 	ret = ceph_cls_lock(osdc, &rbd_dev->header_oid, &rbd_dev->header_oloc,
 			    RBD_LOCK_NAME, CEPH_CLS_LOCK_EXCLUSIVE, cookie,
 			    RBD_LOCK_TAG, "", 0);
-	if (ret)
+	if (ret && ret != -EEXIST)
 		return ret;
 
 	__rbd_lock(rbd_dev, cookie);
@@ -3819,61 +3841,97 @@
 		return;
 	}
 
-	list_for_each_entry(img_req, &rbd_dev->acquiring_list, lock_item) {
+	while (!list_empty(&rbd_dev->acquiring_list)) {
+		img_req = list_first_entry(&rbd_dev->acquiring_list,
+					   struct rbd_img_request, lock_item);
 		mutex_lock(&img_req->state_mutex);
 		rbd_assert(img_req->state == RBD_IMG_EXCLUSIVE_LOCK);
+		if (!result)
+			list_move_tail(&img_req->lock_item,
+				       &rbd_dev->running_list);
+		else
+			list_del_init(&img_req->lock_item);
 		rbd_img_schedule(img_req, result);
 		mutex_unlock(&img_req->state_mutex);
 	}
+}
 
-	list_splice_tail_init(&rbd_dev->acquiring_list, &rbd_dev->running_list);
+static bool locker_equal(const struct ceph_locker *lhs,
+			 const struct ceph_locker *rhs)
+{
+	return lhs->id.name.type == rhs->id.name.type &&
+	       lhs->id.name.num == rhs->id.name.num &&
+	       !strcmp(lhs->id.cookie, rhs->id.cookie) &&
+	       ceph_addr_equal_no_type(&lhs->info.addr, &rhs->info.addr);
+}
+
+static void free_locker(struct ceph_locker *locker)
+{
+	if (locker)
+		ceph_free_lockers(locker, 1);
 }
 
-static int get_lock_owner_info(struct rbd_device *rbd_dev,
-			       struct ceph_locker **lockers, u32 *num_lockers)
+static struct ceph_locker *get_lock_owner_info(struct rbd_device *rbd_dev)
 {
 	struct ceph_osd_client *osdc = &rbd_dev->rbd_client->client->osdc;
+	struct ceph_locker *lockers;
+	u32 num_lockers;
 	u8 lock_type;
 	char *lock_tag;
+	u64 handle;
 	int ret;
 
-	dout("%s rbd_dev %p\n", __func__, rbd_dev);
-
 	ret = ceph_cls_lock_info(osdc, &rbd_dev->header_oid,
 				 &rbd_dev->header_oloc, RBD_LOCK_NAME,
-				 &lock_type, &lock_tag, lockers, num_lockers);
-	if (ret)
-		return ret;
+				 &lock_type, &lock_tag, &lockers, &num_lockers);
+	if (ret) {
+		rbd_warn(rbd_dev, "failed to get header lockers: %d", ret);
+		return ERR_PTR(ret);
+	}
 
-	if (*num_lockers == 0) {
+	if (num_lockers == 0) {
 		dout("%s rbd_dev %p no lockers detected\n", __func__, rbd_dev);
+		lockers = NULL;
 		goto out;
 	}
 
 	if (strcmp(lock_tag, RBD_LOCK_TAG)) {
 		rbd_warn(rbd_dev, "locked by external mechanism, tag %s",
 			 lock_tag);
-		ret = -EBUSY;
-		goto out;
+		goto err_busy;
 	}
 
-	if (lock_type == CEPH_CLS_LOCK_SHARED) {
-		rbd_warn(rbd_dev, "shared lock type detected");
-		ret = -EBUSY;
-		goto out;
+	if (lock_type != CEPH_CLS_LOCK_EXCLUSIVE) {
+		rbd_warn(rbd_dev, "incompatible lock type detected");
+		goto err_busy;
 	}
 
-	if (strncmp((*lockers)[0].id.cookie, RBD_LOCK_COOKIE_PREFIX,
-		    strlen(RBD_LOCK_COOKIE_PREFIX))) {
+	WARN_ON(num_lockers != 1);
+	ret = sscanf(lockers[0].id.cookie, RBD_LOCK_COOKIE_PREFIX " %llu",
+		     &handle);
+	if (ret != 1) {
 		rbd_warn(rbd_dev, "locked by external mechanism, cookie %s",
-			 (*lockers)[0].id.cookie);
-		ret = -EBUSY;
-		goto out;
+			 lockers[0].id.cookie);
+		goto err_busy;
+	}
+	if (ceph_addr_is_blank(&lockers[0].info.addr)) {
+		rbd_warn(rbd_dev, "locker has a blank address");
+		goto err_busy;
 	}
 
+	dout("%s rbd_dev %p got locker %s%llu@%pISpc/%u handle %llu\n",
+	     __func__, rbd_dev, ENTITY_NAME(lockers[0].id.name),
+	     &lockers[0].info.addr.in_addr,
+	     le32_to_cpu(lockers[0].info.addr.nonce), handle);
+
 out:
 	kfree(lock_tag);
-	return ret;
+	return lockers;
+
+err_busy:
+	kfree(lock_tag);
+	ceph_free_lockers(lockers, num_lockers);
+	return ERR_PTR(-EBUSY);
 }
 
 static int find_watcher(struct rbd_device *rbd_dev,
@@ -3889,8 +3947,10 @@
 	ret = ceph_osdc_list_watchers(osdc, &rbd_dev->header_oid,
 				      &rbd_dev->header_oloc, &watchers,
 				      &num_watchers);
-	if (ret)
+	if (ret) {
+		rbd_warn(rbd_dev, "failed to get watchers: %d", ret);
 		return ret;
+	}
 
 	sscanf(locker->id.cookie, RBD_LOCK_COOKIE_PREFIX " %llu", &cookie);
 	for (i = 0; i < num_watchers; i++) {
@@ -3927,51 +3987,72 @@
 static int rbd_try_lock(struct rbd_device *rbd_dev)
 {
 	struct ceph_client *client = rbd_dev->rbd_client->client;
-	struct ceph_locker *lockers;
-	u32 num_lockers;
+	struct ceph_locker *locker, *refreshed_locker;
 	int ret;
 
 	for (;;) {
+		locker = refreshed_locker = NULL;
+
 		ret = rbd_lock(rbd_dev);
-		if (ret != -EBUSY)
-			return ret;
+		if (!ret)
+			goto out;
+		if (ret != -EBUSY) {
+			rbd_warn(rbd_dev, "failed to lock header: %d", ret);
+			goto out;
+		}
 
 		/* determine if the current lock holder is still alive */
-		ret = get_lock_owner_info(rbd_dev, &lockers, &num_lockers);
-		if (ret)
-			return ret;
-
-		if (num_lockers == 0)
+		locker = get_lock_owner_info(rbd_dev);
+		if (IS_ERR(locker)) {
+			ret = PTR_ERR(locker);
+			locker = NULL;
+			goto out;
+		}
+		if (!locker)
 			goto again;
 
-		ret = find_watcher(rbd_dev, lockers);
+		ret = find_watcher(rbd_dev, locker);
 		if (ret)
 			goto out; /* request lock or error */
 
+		refreshed_locker = get_lock_owner_info(rbd_dev);
+		if (IS_ERR(refreshed_locker)) {
+			ret = PTR_ERR(refreshed_locker);
+			refreshed_locker = NULL;
+			goto out;
+		}
+		if (!refreshed_locker ||
+		    !locker_equal(locker, refreshed_locker))
+			goto again;
+
 		rbd_warn(rbd_dev, "breaking header lock owned by %s%llu",
-			 ENTITY_NAME(lockers[0].id.name));
+			 ENTITY_NAME(locker->id.name));
 
 		ret = ceph_monc_blocklist_add(&client->monc,
-					      &lockers[0].info.addr);
+					      &locker->info.addr);
 		if (ret) {
-			rbd_warn(rbd_dev, "blocklist of %s%llu failed: %d",
-				 ENTITY_NAME(lockers[0].id.name), ret);
+			rbd_warn(rbd_dev, "failed to blocklist %s%llu: %d",
+				 ENTITY_NAME(locker->id.name), ret);
 			goto out;
 		}
 
 		ret = ceph_cls_break_lock(&client->osdc, &rbd_dev->header_oid,
 					  &rbd_dev->header_oloc, RBD_LOCK_NAME,
-					  lockers[0].id.cookie,
-					  &lockers[0].id.name);
-		if (ret && ret != -ENOENT)
+					  locker->id.cookie, &locker->id.name);
+		if (ret && ret != -ENOENT) {
+			rbd_warn(rbd_dev, "failed to break header lock: %d",
+				 ret);
 			goto out;
+		}
 
 again:
-		ceph_free_lockers(lockers, num_lockers);
+		free_locker(refreshed_locker);
+		free_locker(locker);
 	}
 
 out:
-	ceph_free_lockers(lockers, num_lockers);
+	free_locker(refreshed_locker);
+	free_locker(locker);
 	return ret;
 }
 
@@ -3979,6 +4060,10 @@
 {
 	int ret;
 
+	ret = rbd_dev_refresh(rbd_dev);
+	if (ret)
+		return ret;
+
 	if (rbd_dev->header.features & RBD_FEATURE_OBJECT_MAP) {
 		ret = rbd_object_map_open(rbd_dev);
 		if (ret)
@@ -4017,11 +4102,8 @@
 
 	ret = rbd_try_lock(rbd_dev);
 	if (ret < 0) {
-		rbd_warn(rbd_dev, "failed to lock header: %d", ret);
-		if (ret == -EBLOCKLISTED)
-			goto out;
-
-		ret = 1; /* request lock anyway */
+		rbd_warn(rbd_dev, "failed to acquire lock: %d", ret);
+		goto out;
 	}
 	if (ret > 0) {
 		up_write(&rbd_dev->lock_rwsem);
@@ -4097,16 +4179,16 @@
 	/*
 	 * Ensure that all in-flight IO is flushed.
 	 */
-	rbd_dev->lock_state = RBD_LOCK_STATE_RELEASING;
-	rbd_assert(!completion_done(&rbd_dev->releasing_wait));
+	rbd_dev->lock_state = RBD_LOCK_STATE_QUIESCING;
+	rbd_assert(!completion_done(&rbd_dev->quiescing_wait));
 	if (list_empty(&rbd_dev->running_list))
 		return true;
 
 	up_write(&rbd_dev->lock_rwsem);
-	wait_for_completion(&rbd_dev->releasing_wait);
+	wait_for_completion(&rbd_dev->quiescing_wait);
 
 	down_write(&rbd_dev->lock_rwsem);
-	if (rbd_dev->lock_state != RBD_LOCK_STATE_RELEASING)
+	if (rbd_dev->lock_state != RBD_LOCK_STATE_QUIESCING)
 		return false;
 
 	rbd_assert(list_empty(&rbd_dev->running_list));
@@ -4517,6 +4599,10 @@
 			rbd_warn(rbd_dev, "failed to update lock cookie: %d",
 				 ret);
 
+		if (rbd_dev->opts->exclusive)
+			rbd_warn(rbd_dev,
+			     "temporarily releasing lock on exclusive mapping");
+
 		/*
 		 * Lock cookie cannot be updated on older OSDs, so do
 		 * a manual release and queue an acquire.
@@ -4784,7 +4870,9 @@
  * return, the rbd_dev->header field will contain up-to-date
  * information about the image.
  */
-static int rbd_dev_v1_header_info(struct rbd_device *rbd_dev)
+static int rbd_dev_v1_header_info(struct rbd_device *rbd_dev,
+				  struct rbd_image_header *header,
+				  bool first_time)
 {
 	struct rbd_image_header_ondisk *ondisk = NULL;
 	u32 snap_count = 0;
@@ -4832,7 +4920,7 @@
 		snap_count = le32_to_cpu(ondisk->snap_count);
 	} while (snap_count != want_count);
 
-	ret = rbd_header_from_disk(rbd_dev, ondisk);
+	ret = rbd_header_from_disk(header, ondisk, first_time);
 out:
 	kfree(ondisk);
 
@@ -4856,39 +4944,6 @@
 	}
 }
 
-static int rbd_dev_refresh(struct rbd_device *rbd_dev)
-{
-	u64 mapping_size;
-	int ret;
-
-	down_write(&rbd_dev->header_rwsem);
-	mapping_size = rbd_dev->mapping.size;
-
-	ret = rbd_dev_header_info(rbd_dev);
-	if (ret)
-		goto out;
-
-	/*
-	 * If there is a parent, see if it has disappeared due to the
-	 * mapped image getting flattened.
-	 */
-	if (rbd_dev->parent) {
-		ret = rbd_dev_v2_parent_info(rbd_dev);
-		if (ret)
-			goto out;
-	}
-
-	rbd_assert(!rbd_is_snap(rbd_dev));
-	rbd_dev->mapping.size = rbd_dev->header.image_size;
-
-out:
-	up_write(&rbd_dev->header_rwsem);
-	if (!ret && mapping_size != rbd_dev->mapping.size)
-		rbd_dev_update_size(rbd_dev);
-
-	return ret;
-}
-
 static const struct blk_mq_ops rbd_mq_ops = {
 	.queue_rq	= rbd_queue_rq,
 };
@@ -5296,8 +5351,7 @@
 		module_put(THIS_MODULE);
 }
 
-static struct rbd_device *__rbd_dev_create(struct rbd_client *rbdc,
-					   struct rbd_spec *spec)
+static struct rbd_device *__rbd_dev_create(struct rbd_spec *spec)
 {
 	struct rbd_device *rbd_dev;
 
@@ -5333,7 +5387,7 @@
 	INIT_LIST_HEAD(&rbd_dev->acquiring_list);
 	INIT_LIST_HEAD(&rbd_dev->running_list);
 	init_completion(&rbd_dev->acquire_wait);
-	init_completion(&rbd_dev->releasing_wait);
+	init_completion(&rbd_dev->quiescing_wait);
 
 	spin_lock_init(&rbd_dev->object_map_lock);
 
@@ -5342,9 +5396,6 @@
 	rbd_dev->dev.parent = &rbd_root_dev;
 	device_initialize(&rbd_dev->dev);
 
-	rbd_dev->rbd_client = rbdc;
-	rbd_dev->spec = spec;
-
 	return rbd_dev;
 }
 
@@ -5357,12 +5408,10 @@
 {
 	struct rbd_device *rbd_dev;
 
-	rbd_dev = __rbd_dev_create(rbdc, spec);
+	rbd_dev = __rbd_dev_create(spec);
 	if (!rbd_dev)
 		return NULL;
 
-	rbd_dev->opts = opts;
-
 	/* get an id and fill in device name */
 	rbd_dev->dev_id = ida_simple_get(&rbd_dev_id_ida, 0,
 					 minor_to_rbd_dev_id(1 << MINORBITS),
@@ -5379,6 +5428,10 @@
 	/* we have a ref from do_rbd_add() */
 	__module_get(THIS_MODULE);
 
+	rbd_dev->rbd_client = rbdc;
+	rbd_dev->spec = spec;
+	rbd_dev->opts = opts;
+
 	dout("%s rbd_dev %p dev_id %d\n", __func__, rbd_dev, rbd_dev->dev_id);
 	return rbd_dev;
 
@@ -5433,17 +5486,12 @@
 	return 0;
 }
 
-static int rbd_dev_v2_image_size(struct rbd_device *rbd_dev)
-{
-	return _rbd_dev_v2_snap_size(rbd_dev, CEPH_NOSNAP,
-					&rbd_dev->header.obj_order,
-					&rbd_dev->header.image_size);
-}
-
-static int rbd_dev_v2_object_prefix(struct rbd_device *rbd_dev)
+static int rbd_dev_v2_object_prefix(struct rbd_device *rbd_dev,
+				    char **pobject_prefix)
 {
 	size_t size;
 	void *reply_buf;
+	char *object_prefix;
 	int ret;
 	void *p;
 
@@ -5461,16 +5509,16 @@
 		goto out;
 
 	p = reply_buf;
-	rbd_dev->header.object_prefix = ceph_extract_encoded_string(&p,
-						p + ret, NULL, GFP_NOIO);
+	object_prefix = ceph_extract_encoded_string(&p, p + ret, NULL,
+						    GFP_NOIO);
+	if (IS_ERR(object_prefix)) {
+		ret = PTR_ERR(object_prefix);
+		goto out;
+	}
 	ret = 0;
 
-	if (IS_ERR(rbd_dev->header.object_prefix)) {
-		ret = PTR_ERR(rbd_dev->header.object_prefix);
-		rbd_dev->header.object_prefix = NULL;
-	} else {
-		dout("  object_prefix = %s\n", rbd_dev->header.object_prefix);
-	}
+	*pobject_prefix = object_prefix;
+	dout("  object_prefix = %s\n", object_prefix);
 out:
 	kfree(reply_buf);
 
@@ -5521,13 +5569,6 @@
 	return 0;
 }
 
-static int rbd_dev_v2_features(struct rbd_device *rbd_dev)
-{
-	return _rbd_dev_v2_snap_features(rbd_dev, CEPH_NOSNAP,
-					 rbd_is_ro(rbd_dev),
-					 &rbd_dev->header.features);
-}
-
 /*
  * These are generic image flags, but since they are used only for
  * object map, store them in rbd_dev->object_map_flags.
@@ -5564,6 +5605,14 @@
 	u64		overlap;
 };
 
+static void rbd_parent_info_cleanup(struct parent_image_info *pii)
+{
+	kfree(pii->pool_ns);
+	kfree(pii->image_id);
+
+	memset(pii, 0, sizeof(*pii));
+}
+
 /*
  * The caller is responsible for @pii.
  */
@@ -5633,6 +5682,9 @@
 	if (pii->has_overlap)
 		ceph_decode_64_safe(&p, end, pii->overlap, e_inval);
 
+	dout("%s pool_id %llu pool_ns %s image_id %s snap_id %llu has_overlap %d overlap %llu\n",
+	     __func__, pii->pool_id, pii->pool_ns, pii->image_id, pii->snap_id,
+	     pii->has_overlap, pii->overlap);
 	return 0;
 
 e_inval:
@@ -5671,14 +5723,17 @@
 	pii->has_overlap = true;
 	ceph_decode_64_safe(&p, end, pii->overlap, e_inval);
 
+	dout("%s pool_id %llu pool_ns %s image_id %s snap_id %llu has_overlap %d overlap %llu\n",
+	     __func__, pii->pool_id, pii->pool_ns, pii->image_id, pii->snap_id,
+	     pii->has_overlap, pii->overlap);
 	return 0;
 
 e_inval:
 	return -EINVAL;
 }
 
-static int get_parent_info(struct rbd_device *rbd_dev,
-			   struct parent_image_info *pii)
+static int rbd_dev_v2_parent_info(struct rbd_device *rbd_dev,
+				  struct parent_image_info *pii)
 {
 	struct page *req_page, *reply_page;
 	void *p;
@@ -5706,7 +5761,7 @@
 	return ret;
 }
 
-static int rbd_dev_v2_parent_info(struct rbd_device *rbd_dev)
+static int rbd_dev_setup_parent(struct rbd_device *rbd_dev)
 {
 	struct rbd_spec *parent_spec;
 	struct parent_image_info pii = { 0 };
@@ -5716,37 +5771,12 @@
 	if (!parent_spec)
 		return -ENOMEM;
 
-	ret = get_parent_info(rbd_dev, &pii);
+	ret = rbd_dev_v2_parent_info(rbd_dev, &pii);
 	if (ret)
 		goto out_err;
 
-	dout("%s pool_id %llu pool_ns %s image_id %s snap_id %llu has_overlap %d overlap %llu\n",
-	     __func__, pii.pool_id, pii.pool_ns, pii.image_id, pii.snap_id,
-	     pii.has_overlap, pii.overlap);
-
-	if (pii.pool_id == CEPH_NOPOOL || !pii.has_overlap) {
-		/*
-		 * Either the parent never existed, or we have
-		 * record of it but the image got flattened so it no
-		 * longer has a parent.  When the parent of a
-		 * layered image disappears we immediately set the
-		 * overlap to 0.  The effect of this is that all new
-		 * requests will be treated as if the image had no
-		 * parent.
-		 *
-		 * If !pii.has_overlap, the parent image spec is not
-		 * applicable.  It's there to avoid duplication in each
-		 * snapshot record.
-		 */
-		if (rbd_dev->parent_overlap) {
-			rbd_dev->parent_overlap = 0;
-			rbd_dev_parent_put(rbd_dev);
-			pr_info("%s: clone image has been flattened\n",
-				rbd_dev->disk->disk_name);
-		}
-
+	if (pii.pool_id == CEPH_NOPOOL || !pii.has_overlap)
 		goto out;	/* No parent?  No problem. */
-	}
 
 	/* The ceph file layout needs to fit pool id in 32 bits */
 
@@ -5758,58 +5788,46 @@
 	}
 
 	/*
-	 * The parent won't change (except when the clone is
-	 * flattened, already handled that).  So we only need to
-	 * record the parent spec we have not already done so.
+	 * The parent won't change except when the clone is flattened,
+	 * so we only need to record the parent image spec once.
 	 */
-	if (!rbd_dev->parent_spec) {
-		parent_spec->pool_id = pii.pool_id;
-		if (pii.pool_ns && *pii.pool_ns) {
-			parent_spec->pool_ns = pii.pool_ns;
-			pii.pool_ns = NULL;
-		}
-		parent_spec->image_id = pii.image_id;
-		pii.image_id = NULL;
-		parent_spec->snap_id = pii.snap_id;
-
-		rbd_dev->parent_spec = parent_spec;
-		parent_spec = NULL;	/* rbd_dev now owns this */
-	}
+	parent_spec->pool_id = pii.pool_id;
+	if (pii.pool_ns && *pii.pool_ns) {
+		parent_spec->pool_ns = pii.pool_ns;
+		pii.pool_ns = NULL;
+	}
+	parent_spec->image_id = pii.image_id;
+	pii.image_id = NULL;
+	parent_spec->snap_id = pii.snap_id;
+
+	rbd_assert(!rbd_dev->parent_spec);
+	rbd_dev->parent_spec = parent_spec;
+	parent_spec = NULL;	/* rbd_dev now owns this */
 
 	/*
-	 * We always update the parent overlap.  If it's zero we issue
-	 * a warning, as we will proceed as if there was no parent.
+	 * Record the parent overlap.  If it's zero, issue a warning as
+	 * we will proceed as if there is no parent.
 	 */
-	if (!pii.overlap) {
-		if (parent_spec) {
-			/* refresh, careful to warn just once */
-			if (rbd_dev->parent_overlap)
-				rbd_warn(rbd_dev,
-				    "clone now standalone (overlap became 0)");
-		} else {
-			/* initial probe */
-			rbd_warn(rbd_dev, "clone is standalone (overlap 0)");
-		}
-	}
+	if (!pii.overlap)
+		rbd_warn(rbd_dev, "clone is standalone (overlap 0)");
 	rbd_dev->parent_overlap = pii.overlap;
 
 out:
 	ret = 0;
 out_err:
-	kfree(pii.pool_ns);
-	kfree(pii.image_id);
+	rbd_parent_info_cleanup(&pii);
 	rbd_spec_put(parent_spec);
 	return ret;
 }
 
-static int rbd_dev_v2_striping_info(struct rbd_device *rbd_dev)
+static int rbd_dev_v2_striping_info(struct rbd_device *rbd_dev,
+				    u64 *stripe_unit, u64 *stripe_count)
 {
 	struct {
 		__le64 stripe_unit;
 		__le64 stripe_count;
 	} __attribute__ ((packed)) striping_info_buf = { 0 };
 	size_t size = sizeof (striping_info_buf);
-	void *p;
 	int ret;
 
 	ret = rbd_obj_method_sync(rbd_dev, &rbd_dev->header_oid,
@@ -5821,27 +5839,33 @@
 	if (ret < size)
 		return -ERANGE;
 
-	p = &striping_info_buf;
-	rbd_dev->header.stripe_unit = ceph_decode_64(&p);
-	rbd_dev->header.stripe_count = ceph_decode_64(&p);
+	*stripe_unit = le64_to_cpu(striping_info_buf.stripe_unit);
+	*stripe_count = le64_to_cpu(striping_info_buf.stripe_count);
+	dout("  stripe_unit = %llu stripe_count = %llu\n", *stripe_unit,
+	     *stripe_count);
+
 	return 0;
 }
 
-static int rbd_dev_v2_data_pool(struct rbd_device *rbd_dev)
+static int rbd_dev_v2_data_pool(struct rbd_device *rbd_dev, s64 *data_pool_id)
 {
-	__le64 data_pool_id;
+	__le64 data_pool_buf;
 	int ret;
 
 	ret = rbd_obj_method_sync(rbd_dev, &rbd_dev->header_oid,
 				  &rbd_dev->header_oloc, "get_data_pool",
-				  NULL, 0, &data_pool_id, sizeof(data_pool_id));
+				  NULL, 0, &data_pool_buf,
+				  sizeof(data_pool_buf));
+	dout("%s: rbd_obj_method_sync returned %d\n", __func__, ret);
 	if (ret < 0)
 		return ret;
-	if (ret < sizeof(data_pool_id))
+	if (ret < sizeof(data_pool_buf))
 		return -EBADMSG;
 
-	rbd_dev->header.data_pool_id = le64_to_cpu(data_pool_id);
-	WARN_ON(rbd_dev->header.data_pool_id == CEPH_NOPOOL);
+	*data_pool_id = le64_to_cpu(data_pool_buf);
+	dout("  data_pool_id = %lld\n", *data_pool_id);
+	WARN_ON(*data_pool_id == CEPH_NOPOOL);
+
 	return 0;
 }
 
@@ -6033,7 +6057,8 @@
 	return ret;
 }
 
-static int rbd_dev_v2_snap_context(struct rbd_device *rbd_dev)
+static int rbd_dev_v2_snap_context(struct rbd_device *rbd_dev,
+				   struct ceph_snap_context **psnapc)
 {
 	size_t size;
 	int ret;
@@ -6094,9 +6119,7 @@
 	for (i = 0; i < snap_count; i++)
 		snapc->snaps[i] = ceph_decode_64(&p);
 
-	ceph_put_snap_context(rbd_dev->header.snapc);
-	rbd_dev->header.snapc = snapc;
-
+	*psnapc = snapc;
 	dout("  snap context seq = %llu, snap_count = %u\n",
 		(unsigned long long)seq, (unsigned int)snap_count);
 out:
@@ -6145,38 +6168,42 @@
 	return snap_name;
 }
 
-static int rbd_dev_v2_header_info(struct rbd_device *rbd_dev)
+static int rbd_dev_v2_header_info(struct rbd_device *rbd_dev,
+				  struct rbd_image_header *header,
+				  bool first_time)
 {
-	bool first_time = rbd_dev->header.object_prefix == NULL;
 	int ret;
 
-	ret = rbd_dev_v2_image_size(rbd_dev);
+	ret = _rbd_dev_v2_snap_size(rbd_dev, CEPH_NOSNAP,
+				    first_time ? &header->obj_order : NULL,
+				    &header->image_size);
 	if (ret)
 		return ret;
 
 	if (first_time) {
-		ret = rbd_dev_v2_header_onetime(rbd_dev);
+		ret = rbd_dev_v2_header_onetime(rbd_dev, header);
 		if (ret)
 			return ret;
 	}
 
-	ret = rbd_dev_v2_snap_context(rbd_dev);
-	if (ret && first_time) {
-		kfree(rbd_dev->header.object_prefix);
-		rbd_dev->header.object_prefix = NULL;
-	}
+	ret = rbd_dev_v2_snap_context(rbd_dev, &header->snapc);
+	if (ret)
+		return ret;
 
-	return ret;
+	return 0;
 }
 
-static int rbd_dev_header_info(struct rbd_device *rbd_dev)
+static int rbd_dev_header_info(struct rbd_device *rbd_dev,
+			       struct rbd_image_header *header,
+			       bool first_time)
 {
 	rbd_assert(rbd_image_format_valid(rbd_dev->image_format));
+	rbd_assert(!header->object_prefix && !header->snapc);
 
 	if (rbd_dev->image_format == 1)
-		return rbd_dev_v1_header_info(rbd_dev);
+		return rbd_dev_v1_header_info(rbd_dev, header, first_time);
 
-	return rbd_dev_v2_header_info(rbd_dev);
+	return rbd_dev_v2_header_info(rbd_dev, header, first_time);
 }
 
 /*
@@ -6559,18 +6586,12 @@
 		cancel_delayed_work_sync(&rbd_dev->lock_dwork);
 		if (!ret)
 			ret = -ETIMEDOUT;
-	}
 
-	if (ret) {
-		rbd_warn(rbd_dev, "failed to acquire exclusive lock: %ld", ret);
-		return ret;
+		rbd_warn(rbd_dev, "failed to acquire lock: %ld", ret);
 	}
+	if (ret)
+		return ret;
 
-	/*
-	 * The lock may have been released by now, unless automatic lock
-	 * transitions are disabled.
-	 */
-	rbd_assert(!rbd_dev->opts->exclusive || rbd_is_lock_owner(rbd_dev));
 	return 0;
 }
 
@@ -6664,60 +6685,49 @@
  */
 static void rbd_dev_unprobe(struct rbd_device *rbd_dev)
 {
-	struct rbd_image_header	*header;
-
 	rbd_dev_parent_put(rbd_dev);
 	rbd_object_map_free(rbd_dev);
 	rbd_dev_mapping_clear(rbd_dev);
 
 	/* Free dynamic fields from the header, then zero it out */
 
-	header = &rbd_dev->header;
-	ceph_put_snap_context(header->snapc);
-	kfree(header->snap_sizes);
-	kfree(header->snap_names);
-	kfree(header->object_prefix);
-	memset(header, 0, sizeof (*header));
+	rbd_image_header_cleanup(&rbd_dev->header);
 }
 
-static int rbd_dev_v2_header_onetime(struct rbd_device *rbd_dev)
+static int rbd_dev_v2_header_onetime(struct rbd_device *rbd_dev,
+				     struct rbd_image_header *header)
 {
 	int ret;
 
-	ret = rbd_dev_v2_object_prefix(rbd_dev);
+	ret = rbd_dev_v2_object_prefix(rbd_dev, &header->object_prefix);
 	if (ret)
-		goto out_err;
+		return ret;
 
 	/*
 	 * Get the and check features for the image.  Currently the
 	 * features are assumed to never change.
 	 */
-	ret = rbd_dev_v2_features(rbd_dev);
+	ret = _rbd_dev_v2_snap_features(rbd_dev, CEPH_NOSNAP,
+					rbd_is_ro(rbd_dev), &header->features);
 	if (ret)
-		goto out_err;
+		return ret;
 
 	/* If the image supports fancy striping, get its parameters */
 
-	if (rbd_dev->header.features & RBD_FEATURE_STRIPINGV2) {
-		ret = rbd_dev_v2_striping_info(rbd_dev);
-		if (ret < 0)
-			goto out_err;
+	if (header->features & RBD_FEATURE_STRIPINGV2) {
+		ret = rbd_dev_v2_striping_info(rbd_dev, &header->stripe_unit,
+					       &header->stripe_count);
+		if (ret)
+			return ret;
 	}
 
-	if (rbd_dev->header.features & RBD_FEATURE_DATA_POOL) {
-		ret = rbd_dev_v2_data_pool(rbd_dev);
+	if (header->features & RBD_FEATURE_DATA_POOL) {
+		ret = rbd_dev_v2_data_pool(rbd_dev, &header->data_pool_id);
 		if (ret)
-			goto out_err;
+			return ret;
 	}
 
-	rbd_init_layout(rbd_dev);
 	return 0;
-
-out_err:
-	rbd_dev->header.features = 0;
-	kfree(rbd_dev->header.object_prefix);
-	rbd_dev->header.object_prefix = NULL;
-	return ret;
 }
 
 /*
@@ -6739,7 +6749,7 @@
 		goto out_err;
 	}
 
-	parent = __rbd_dev_create(rbd_dev->rbd_client, rbd_dev->parent_spec);
+	parent = __rbd_dev_create(rbd_dev->parent_spec);
 	if (!parent) {
 		ret = -ENOMEM;
 		goto out_err;
@@ -6749,8 +6759,8 @@
 	 * Images related by parent/child relationships always share
 	 * rbd_client and spec/parent_spec, so bump their refcounts.
 	 */
-	__rbd_get_client(rbd_dev->rbd_client);
-	rbd_spec_get(rbd_dev->parent_spec);
+	parent->rbd_client = __rbd_get_client(rbd_dev->rbd_client);
+	parent->spec = rbd_spec_get(rbd_dev->parent_spec);
 
 	__set_bit(RBD_DEV_FLAG_READONLY, &parent->flags);
 
@@ -6912,13 +6922,15 @@
 	if (!depth)
 		down_write(&rbd_dev->header_rwsem);
 
-	ret = rbd_dev_header_info(rbd_dev);
+	ret = rbd_dev_header_info(rbd_dev, &rbd_dev->header, true);
 	if (ret) {
 		if (ret == -ENOENT && !need_watch)
 			rbd_print_dne(rbd_dev, false);
 		goto err_out_probe;
 	}
 
+	rbd_init_layout(rbd_dev);
+
 	/*
 	 * If this image is the one being mapped, we have pool name and
 	 * id, image name and id, and snap name - need to fill snap id.
@@ -6947,7 +6959,7 @@
 	}
 
 	if (rbd_dev->header.features & RBD_FEATURE_LAYERING) {
-		ret = rbd_dev_v2_parent_info(rbd_dev);
+		ret = rbd_dev_setup_parent(rbd_dev);
 		if (ret)
 			goto err_out_probe;
 	}
@@ -6973,6 +6985,107 @@
 	return ret;
 }
 
+static void rbd_dev_update_header(struct rbd_device *rbd_dev,
+				  struct rbd_image_header *header)
+{
+	rbd_assert(rbd_image_format_valid(rbd_dev->image_format));
+	rbd_assert(rbd_dev->header.object_prefix); /* !first_time */
+
+	if (rbd_dev->header.image_size != header->image_size) {
+		rbd_dev->header.image_size = header->image_size;
+
+		if (!rbd_is_snap(rbd_dev)) {
+			rbd_dev->mapping.size = header->image_size;
+			rbd_dev_update_size(rbd_dev);
+		}
+	}
+
+	ceph_put_snap_context(rbd_dev->header.snapc);
+	rbd_dev->header.snapc = header->snapc;
+	header->snapc = NULL;
+
+	if (rbd_dev->image_format == 1) {
+		kfree(rbd_dev->header.snap_names);
+		rbd_dev->header.snap_names = header->snap_names;
+		header->snap_names = NULL;
+
+		kfree(rbd_dev->header.snap_sizes);
+		rbd_dev->header.snap_sizes = header->snap_sizes;
+		header->snap_sizes = NULL;
+	}
+}
+
+static void rbd_dev_update_parent(struct rbd_device *rbd_dev,
+				  struct parent_image_info *pii)
+{
+	if (pii->pool_id == CEPH_NOPOOL || !pii->has_overlap) {
+		/*
+		 * Either the parent never existed, or we have
+		 * record of it but the image got flattened so it no
+		 * longer has a parent.  When the parent of a
+		 * layered image disappears we immediately set the
+		 * overlap to 0.  The effect of this is that all new
+		 * requests will be treated as if the image had no
+		 * parent.
+		 *
+		 * If !pii.has_overlap, the parent image spec is not
+		 * applicable.  It's there to avoid duplication in each
+		 * snapshot record.
+		 */
+		if (rbd_dev->parent_overlap) {
+			rbd_dev->parent_overlap = 0;
+			rbd_dev_parent_put(rbd_dev);
+			pr_info("%s: clone has been flattened\n",
+				rbd_dev->disk->disk_name);
+		}
+	} else {
+		rbd_assert(rbd_dev->parent_spec);
+
+		/*
+		 * Update the parent overlap.  If it became zero, issue
+		 * a warning as we will proceed as if there is no parent.
+		 */
+		if (!pii->overlap && rbd_dev->parent_overlap)
+			rbd_warn(rbd_dev,
+				 "clone has become standalone (overlap 0)");
+		rbd_dev->parent_overlap = pii->overlap;
+	}
+}
+
+static int rbd_dev_refresh(struct rbd_device *rbd_dev)
+{
+	struct rbd_image_header	header = { 0 };
+	struct parent_image_info pii = { 0 };
+	int ret;
+
+	dout("%s rbd_dev %p\n", __func__, rbd_dev);
+
+	ret = rbd_dev_header_info(rbd_dev, &header, false);
+	if (ret)
+		goto out;
+
+	/*
+	 * If there is a parent, see if it has disappeared due to the
+	 * mapped image getting flattened.
+	 */
+	if (rbd_dev->parent) {
+		ret = rbd_dev_v2_parent_info(rbd_dev, &pii);
+		if (ret)
+			goto out;
+	}
+
+	down_write(&rbd_dev->header_rwsem);
+	rbd_dev_update_header(rbd_dev, &header);
+	if (rbd_dev->parent)
+		rbd_dev_update_parent(rbd_dev, &pii);
+	up_write(&rbd_dev->header_rwsem);
+
+out:
+	rbd_parent_info_cleanup(&pii);
+	rbd_image_header_cleanup(&header);
+	return ret;
+}
+
 static ssize_t do_rbd_add(struct bus_type *bus,
 			  const char *buf,
 			  size_t count)
@@ -7182,7 +7295,7 @@
 		 * IO to complete/fail.
 		 */
 		blk_mq_freeze_queue(rbd_dev->disk->queue);
-		blk_set_queue_dying(rbd_dev->disk->queue);
+		blk_mark_disk_dead(rbd_dev->disk);
 	}
 
 	del_gendisk(rbd_dev->disk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/rnbd/rnbd-proto.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/rnbd/rnbd-proto.h
@@ -241,7 +241,7 @@
 		bio_opf = REQ_OP_WRITE;
 		break;
 	case RNBD_OP_FLUSH:
-		bio_opf = REQ_OP_FLUSH | REQ_PREFLUSH;
+		bio_opf = REQ_OP_WRITE | REQ_PREFLUSH;
 		break;
 	case RNBD_OP_DISCARD:
 		bio_opf = REQ_OP_DISCARD;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/rnbd/rnbd-srv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/rnbd/rnbd-srv.c
@@ -266,12 +266,12 @@
 static int create_sess(struct rtrs_srv *rtrs)
 {
 	struct rnbd_srv_session *srv_sess;
-	char sessname[NAME_MAX];
+	char pathname[NAME_MAX];
 	int err;
 
-	err = rtrs_srv_get_sess_name(rtrs, sessname, sizeof(sessname));
+	err = rtrs_srv_get_path_name(rtrs, pathname, sizeof(pathname));
 	if (err) {
-		pr_err("rtrs_srv_get_sess_name(%s): %d\n", sessname, err);
+		pr_err("rtrs_srv_get_path_name(%s): %d\n", pathname, err);
 
 		return err;
 	}
@@ -284,8 +284,8 @@
 			  offsetof(struct rnbd_dev_blk_io, bio),
 			  BIOSET_NEED_BVECS);
 	if (err) {
-		pr_err("Allocating srv_session for session %s failed\n",
-		       sessname);
+		pr_err("Allocating srv_session for path %s failed\n",
+		       pathname);
 		kfree(srv_sess);
 		return err;
 	}
@@ -298,7 +298,7 @@
 	mutex_unlock(&sess_lock);
 
 	srv_sess->rtrs = rtrs;
-	strscpy(srv_sess->sessname, sessname, sizeof(srv_sess->sessname));
+	strscpy(srv_sess->sessname, pathname, sizeof(srv_sess->sessname));
 
 	rtrs_srv_set_sess_priv(rtrs, srv_sess);
 
@@ -333,10 +333,11 @@
 {
 	struct rnbd_srv_session	*sess = sess_dev->sess;
 
-	sess_dev->keep_id = true;
 	/* It is already started to close by client's close message. */
 	if (!mutex_trylock(&sess->lock))
 		return;
+
+	sess_dev->keep_id = true;
 	/* first remove sysfs itself to avoid deadlock */
 	sysfs_remove_file_self(&sess_dev->kobj, &attr->attr);
 	rnbd_srv_destroy_dev_session_sysfs(sess_dev);
@@ -605,6 +606,7 @@
 {
 	char *full_path;
 	char *a, *b;
+	int len;
 
 	full_path = kmalloc(PATH_MAX, GFP_KERNEL);
 	if (!full_path)
@@ -616,19 +618,19 @@
 	 */
 	a = strnstr(dev_search_path, "%SESSNAME%", sizeof(dev_search_path));
 	if (a) {
-		int len = a - dev_search_path;
+		len = a - dev_search_path;
 
 		len = snprintf(full_path, PATH_MAX, "%.*s/%s/%s", len,
 			       dev_search_path, srv_sess->sessname, dev_name);
-		if (len >= PATH_MAX) {
-			pr_err("Too long path: %s, %s, %s\n",
-			       dev_search_path, srv_sess->sessname, dev_name);
-			kfree(full_path);
-			return ERR_PTR(-EINVAL);
-		}
 	} else {
-		snprintf(full_path, PATH_MAX, "%s/%s",
-			 dev_search_path, dev_name);
+		len = snprintf(full_path, PATH_MAX, "%s/%s",
+			       dev_search_path, dev_name);
+	}
+	if (len >= PATH_MAX) {
+		pr_err("Too long path: %s, %s, %s\n",
+		       dev_search_path, srv_sess->sessname, dev_name);
+		kfree(full_path);
+		return ERR_PTR(-EINVAL);
 	}
 
 	/* eliminitate duplicated slashes */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/rsxx/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/rsxx/dev.c
@@ -127,6 +127,8 @@
 	blk_status_t st = BLK_STS_IOERR;
 
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
 	might_sleep();
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/sunvdc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/sunvdc.c
@@ -964,6 +964,8 @@
 	print_version();
 
 	hp = mdesc_grab();
+	if (!hp)
+		return -ENODEV;
 
 	err = -ENODEV;
 	if ((vdev->dev_no << PARTITION_SHIFT) & ~(u64)MINORMASK) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/swim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/swim.c
@@ -16,6 +16,7 @@
 #include <linux/fd.h>
 #include <linux/slab.h>
 #include <linux/blk-mq.h>
+#include <linux/major.h>
 #include <linux/mutex.h>
 #include <linux/hdreg.h>
 #include <linux/kernel.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/virtio_blk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/virtio_blk.c
@@ -24,6 +24,12 @@
 /* The maximum number of sg elements that fit into a virtqueue */
 #define VIRTIO_BLK_MAX_SG_ELEMS 32768
 
+#ifdef CONFIG_ARCH_NO_SG_CHAIN
+#define VIRTIO_BLK_INLINE_SG_CNT	0
+#else
+#define VIRTIO_BLK_INLINE_SG_CNT	2
+#endif
+
 static int major;
 static DEFINE_IDA(vd_index_ida);
 
@@ -77,6 +83,7 @@
 struct virtblk_req {
 	struct virtio_blk_outhdr out_hdr;
 	u8 status;
+	struct sg_table sg_table;
 	struct scatterlist sg[];
 };
 
@@ -162,12 +169,92 @@
 	return 0;
 }
 
-static inline void virtblk_request_done(struct request *req)
+static void virtblk_unmap_data(struct request *req, struct virtblk_req *vbr)
 {
-	struct virtblk_req *vbr = blk_mq_rq_to_pdu(req);
+	if (blk_rq_nr_phys_segments(req))
+		sg_free_table_chained(&vbr->sg_table,
+				      VIRTIO_BLK_INLINE_SG_CNT);
+}
+
+static int virtblk_map_data(struct blk_mq_hw_ctx *hctx, struct request *req,
+		struct virtblk_req *vbr)
+{
+	int err;
+
+	if (!blk_rq_nr_phys_segments(req))
+		return 0;
+
+	vbr->sg_table.sgl = vbr->sg;
+	err = sg_alloc_table_chained(&vbr->sg_table,
+				     blk_rq_nr_phys_segments(req),
+				     vbr->sg_table.sgl,
+				     VIRTIO_BLK_INLINE_SG_CNT);
+	if (unlikely(err))
+		return -ENOMEM;
+
+	return blk_rq_map_sg(hctx->queue, req, vbr->sg_table.sgl);
+}
 
+static void virtblk_cleanup_cmd(struct request *req)
+{
 	if (req->rq_flags & RQF_SPECIAL_PAYLOAD)
 		kfree(bvec_virt(&req->special_vec));
+}
+
+static int virtblk_setup_cmd(struct virtio_device *vdev, struct request *req,
+		struct virtblk_req *vbr)
+{
+	bool unmap = false;
+	u32 type;
+
+	vbr->out_hdr.sector = 0;
+
+	switch (req_op(req)) {
+	case REQ_OP_READ:
+		type = VIRTIO_BLK_T_IN;
+		vbr->out_hdr.sector = cpu_to_virtio64(vdev,
+						      blk_rq_pos(req));
+		break;
+	case REQ_OP_WRITE:
+		type = VIRTIO_BLK_T_OUT;
+		vbr->out_hdr.sector = cpu_to_virtio64(vdev,
+						      blk_rq_pos(req));
+		break;
+	case REQ_OP_FLUSH:
+		type = VIRTIO_BLK_T_FLUSH;
+		break;
+	case REQ_OP_DISCARD:
+		type = VIRTIO_BLK_T_DISCARD;
+		break;
+	case REQ_OP_WRITE_ZEROES:
+		type = VIRTIO_BLK_T_WRITE_ZEROES;
+		unmap = !(req->cmd_flags & REQ_NOUNMAP);
+		break;
+	case REQ_OP_DRV_IN:
+		type = VIRTIO_BLK_T_GET_ID;
+		break;
+	default:
+		WARN_ON_ONCE(1);
+		return BLK_STS_IOERR;
+	}
+
+	vbr->out_hdr.type = cpu_to_virtio32(vdev, type);
+	vbr->out_hdr.ioprio = cpu_to_virtio32(vdev, req_get_ioprio(req));
+
+	if (type == VIRTIO_BLK_T_DISCARD || type == VIRTIO_BLK_T_WRITE_ZEROES) {
+		if (virtblk_setup_discard_write_zeroes(req, unmap))
+			return BLK_STS_RESOURCE;
+	}
+
+	return 0;
+}
+
+static inline void virtblk_request_done(struct request *req)
+{
+	struct virtblk_req *vbr = blk_mq_rq_to_pdu(req);
+
+	virtblk_unmap_data(req, vbr);
+	virtblk_cleanup_cmd(req);
 	blk_mq_end_request(req, virtblk_result(vbr));
 }
 
@@ -221,61 +308,27 @@
 	struct request *req = bd->rq;
 	struct virtblk_req *vbr = blk_mq_rq_to_pdu(req);
 	unsigned long flags;
-	unsigned int num;
+	int num;
 	int qid = hctx->queue_num;
 	int err;
 	bool notify = false;
-	bool unmap = false;
-	u32 type;
 
 	BUG_ON(req->nr_phys_segments + 2 > vblk->sg_elems);
 
-	switch (req_op(req)) {
-	case REQ_OP_READ:
-	case REQ_OP_WRITE:
-		type = 0;
-		break;
-	case REQ_OP_FLUSH:
-		type = VIRTIO_BLK_T_FLUSH;
-		break;
-	case REQ_OP_DISCARD:
-		type = VIRTIO_BLK_T_DISCARD;
-		break;
-	case REQ_OP_WRITE_ZEROES:
-		type = VIRTIO_BLK_T_WRITE_ZEROES;
-		unmap = !(req->cmd_flags & REQ_NOUNMAP);
-		break;
-	case REQ_OP_DRV_IN:
-		type = VIRTIO_BLK_T_GET_ID;
-		break;
-	default:
-		WARN_ON_ONCE(1);
-		return BLK_STS_IOERR;
-	}
-
-	vbr->out_hdr.type = cpu_to_virtio32(vblk->vdev, type);
-	vbr->out_hdr.sector = type ?
-		0 : cpu_to_virtio64(vblk->vdev, blk_rq_pos(req));
-	vbr->out_hdr.ioprio = cpu_to_virtio32(vblk->vdev, req_get_ioprio(req));
+	err = virtblk_setup_cmd(vblk->vdev, req, vbr);
+	if (unlikely(err))
+		return err;
 
 	blk_mq_start_request(req);
 
-	if (type == VIRTIO_BLK_T_DISCARD || type == VIRTIO_BLK_T_WRITE_ZEROES) {
-		err = virtblk_setup_discard_write_zeroes(req, unmap);
-		if (err)
-			return BLK_STS_RESOURCE;
-	}
-
-	num = blk_rq_map_sg(hctx->queue, req, vbr->sg);
-	if (num) {
-		if (rq_data_dir(req) == WRITE)
-			vbr->out_hdr.type |= cpu_to_virtio32(vblk->vdev, VIRTIO_BLK_T_OUT);
-		else
-			vbr->out_hdr.type |= cpu_to_virtio32(vblk->vdev, VIRTIO_BLK_T_IN);
+	num = virtblk_map_data(hctx, req, vbr);
+	if (unlikely(num < 0)) {
+		virtblk_cleanup_cmd(req);
+		return BLK_STS_RESOURCE;
 	}
 
 	spin_lock_irqsave(&vblk->vqs[qid].lock, flags);
-	err = virtblk_add_req(vblk->vqs[qid].vq, vbr, vbr->sg, num);
+	err = virtblk_add_req(vblk->vqs[qid].vq, vbr, vbr->sg_table.sgl, num);
 	if (err) {
 		virtqueue_kick(vblk->vqs[qid].vq);
 		/* Don't stop the queue if -ENOMEM: we may have failed to
@@ -284,6 +337,8 @@
 		if (err == -ENOSPC)
 			blk_mq_stop_hw_queue(hctx);
 		spin_unlock_irqrestore(&vblk->vqs[qid].lock, flags);
+		virtblk_unmap_data(req, vbr);
+		virtblk_cleanup_cmd(req);
 		switch (err) {
 		case -ENOSPC:
 			return BLK_STS_DEV_RESOURCE;
@@ -660,16 +715,6 @@
 	NULL,
 };
 
-static int virtblk_init_request(struct blk_mq_tag_set *set, struct request *rq,
-		unsigned int hctx_idx, unsigned int numa_node)
-{
-	struct virtio_blk *vblk = set->driver_data;
-	struct virtblk_req *vbr = blk_mq_rq_to_pdu(rq);
-
-	sg_init_table(vbr->sg, vblk->sg_elems);
-	return 0;
-}
-
 static int virtblk_map_queues(struct blk_mq_tag_set *set)
 {
 	struct virtio_blk *vblk = set->driver_data;
@@ -682,7 +727,6 @@
 	.queue_rq	= virtio_queue_rq,
 	.commit_rqs	= virtio_commit_rqs,
 	.complete	= virtblk_request_done,
-	.init_request	= virtblk_init_request,
 	.map_queues	= virtblk_map_queues,
 };
 
@@ -699,6 +743,7 @@
 	u16 min_io_size;
 	u8 physical_block_exp, alignment_offset;
 	unsigned int queue_depth;
+	size_t max_dma_size;
 
 	if (!vdev->config->get) {
 		dev_err(&vdev->dev, "%s failure: config access disabled\n",
@@ -762,7 +807,7 @@
 	vblk->tag_set.flags = BLK_MQ_F_SHOULD_MERGE;
 	vblk->tag_set.cmd_size =
 		sizeof(struct virtblk_req) +
-		sizeof(struct scatterlist) * sg_elems;
+		sizeof(struct scatterlist) * VIRTIO_BLK_INLINE_SG_CNT;
 	vblk->tag_set.driver_data = vblk;
 	vblk->tag_set.nr_hw_queues = vblk->num_vqs;
 
@@ -800,7 +845,8 @@
 	/* No real sector limit. */
 	blk_queue_max_hw_sectors(q, -1U);
 
-	max_size = virtio_max_dma_size(vdev);
+	max_dma_size = virtio_max_dma_size(vdev);
+	max_size = max_dma_size > U32_MAX ? U32_MAX : max_dma_size;
 
 	/* Host can optionally specify maximum segment size and number of
 	 * segments. */
@@ -815,9 +861,17 @@
 	err = virtio_cread_feature(vdev, VIRTIO_BLK_F_BLK_SIZE,
 				   struct virtio_blk_config, blk_size,
 				   &blk_size);
-	if (!err)
+	if (!err) {
+		err = blk_validate_block_size(blk_size);
+		if (err) {
+			dev_err(&vdev->dev,
+				"virtio_blk: invalid block size: 0x%x\n",
+				blk_size);
+			goto out_cleanup_disk;
+		}
+
 		blk_queue_logical_block_size(q, blk_size);
-	else
+	} else
 		blk_size = queue_logical_block_size(q);
 
 	/* Use topology information if available */
@@ -847,11 +901,12 @@
 		blk_queue_io_opt(q, blk_size * opt_io_size);
 
 	if (virtio_has_feature(vdev, VIRTIO_BLK_F_DISCARD)) {
-		q->limits.discard_granularity = blk_size;
-
 		virtio_cread(vdev, struct virtio_blk_config,
 			     discard_sector_alignment, &v);
-		q->limits.discard_alignment = v ? v << SECTOR_SHIFT : 0;
+		if (v)
+			q->limits.discard_granularity = v << SECTOR_SHIFT;
+		else
+			q->limits.discard_granularity = blk_size;
 
 		virtio_cread(vdev, struct virtio_blk_config,
 			     max_discard_sectors, &v);
@@ -859,9 +914,15 @@
 
 		virtio_cread(vdev, struct virtio_blk_config, max_discard_seg,
 			     &v);
+
+		/*
+		 * max_discard_seg == 0 is out of spec but we always
+		 * handled it.
+		 */
+		if (!v)
+			v = sg_elems - 2;
 		blk_queue_max_discard_segments(q,
-					       min_not_zero(v,
-							    MAX_DISCARD_SEGMENTS));
+					       min(v, MAX_DISCARD_SEGMENTS));
 
 		blk_queue_flag_set(QUEUE_FLAG_DISCARD, q);
 	}
@@ -927,6 +988,12 @@
 static int virtblk_freeze(struct virtio_device *vdev)
 {
 	struct virtio_blk *vblk = vdev->priv;
+	struct request_queue *q = vblk->disk->queue;
+
+	/* Ensure no requests in virtqueues before deleting vqs. */
+	blk_mq_freeze_queue(q);
+	blk_mq_quiesce_queue_nowait(q);
+	blk_mq_unfreeze_queue(q);
 
 	/* Ensure we don't receive any more interrupts */
 	vdev->config->reset(vdev);
@@ -934,8 +1001,6 @@
 	/* Make sure no work handler is accessing the device. */
 	flush_work(&vblk->config_work);
 
-	blk_mq_quiesce_queue(vblk->disk->queue);
-
 	vdev->config->del_vqs(vdev);
 	kfree(vblk->vqs);
 
@@ -952,8 +1017,8 @@
 		return ret;
 
 	virtio_device_ready(vdev);
-
 	blk_mq_unquiesce_queue(vblk->disk->queue);
+
 	return 0;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/xen-blkback/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/xen-blkback/common.h
@@ -226,6 +226,9 @@
 	sector_t		size;
 	unsigned int		flush_support:1;
 	unsigned int		discard_secure:1;
+	/* Connect-time cached feature_persistent parameter value */
+	unsigned int		feature_gnt_persistent_parm:1;
+	/* Persistent grants feature negotiation result */
 	unsigned int		feature_gnt_persistent:1;
 	unsigned int		overflow_max_grants:1;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/xen-blkback/xenbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/xen-blkback/xenbus.c
@@ -156,6 +156,11 @@
 	return 0;
 }
 
+/* Enable the persistent grants feature. */
+static bool feature_persistent = true;
+module_param(feature_persistent, bool, 0644);
+MODULE_PARM_DESC(feature_persistent, "Enables the persistent grants feature");
+
 static struct xen_blkif *xen_blkif_alloc(domid_t domid)
 {
 	struct xen_blkif *blkif;
@@ -471,12 +476,6 @@
 	vbd->bdev = NULL;
 }
 
-/* Enable the persistent grants feature. */
-static bool feature_persistent = true;
-module_param(feature_persistent, bool, 0644);
-MODULE_PARM_DESC(feature_persistent,
-		"Enables the persistent grants feature");
-
 static int xen_vbd_create(struct xen_blkif *blkif, blkif_vdev_t handle,
 			  unsigned major, unsigned minor, int readonly,
 			  int cdrom)
@@ -522,8 +521,6 @@
 	if (q && blk_queue_secure_erase(q))
 		vbd->discard_secure = true;
 
-	vbd->feature_gnt_persistent = feature_persistent;
-
 	pr_debug("Successful creation of handle=%04x (dom=%u)\n",
 		handle, blkif->domid);
 	return 0;
@@ -913,7 +910,7 @@
 	xen_blkbk_barrier(xbt, be, be->blkif->vbd.flush_support);
 
 	err = xenbus_printf(xbt, dev->nodename, "feature-persistent", "%u",
-			be->blkif->vbd.feature_gnt_persistent);
+			be->blkif->vbd.feature_gnt_persistent_parm);
 	if (err) {
 		xenbus_dev_fatal(dev, err, "writing %s/feature-persistent",
 				 dev->nodename);
@@ -1090,10 +1087,11 @@
 		xenbus_dev_fatal(dev, err, "unknown fe protocol %s", protocol);
 		return -ENOSYS;
 	}
-	if (blkif->vbd.feature_gnt_persistent)
-		blkif->vbd.feature_gnt_persistent =
-			xenbus_read_unsigned(dev->otherend,
-					"feature-persistent", 0);
+
+	blkif->vbd.feature_gnt_persistent_parm = feature_persistent;
+	blkif->vbd.feature_gnt_persistent =
+		blkif->vbd.feature_gnt_persistent_parm &&
+		xenbus_read_unsigned(dev->otherend, "feature-persistent", 0);
 
 	blkif->vbd.overflow_max_grants = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/xen-blkfront.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/xen-blkfront.c
@@ -42,6 +42,7 @@
 #include <linux/cdrom.h>
 #include <linux/module.h>
 #include <linux/slab.h>
+#include <linux/major.h>
 #include <linux/mutex.h>
 #include <linux/scatterlist.h>
 #include <linux/bitmap.h>
@@ -151,6 +152,10 @@
 module_param_named(max_ring_page_order, xen_blkif_max_ring_order, int, 0444);
 MODULE_PARM_DESC(max_ring_page_order, "Maximum order of pages to be used for the shared ring");
 
+static bool __read_mostly xen_blkif_trusted = true;
+module_param_named(trusted, xen_blkif_trusted, bool, 0644);
+MODULE_PARM_DESC(trusted, "Is the backend trusted");
+
 #define BLK_RING_SIZE(info)	\
 	__CONST_RING_SIZE(blkif, XEN_PAGE_SIZE * (info)->nr_ring_pages)
 
@@ -207,7 +212,11 @@
 	unsigned int feature_fua:1;
 	unsigned int feature_discard:1;
 	unsigned int feature_secdiscard:1;
+	/* Connect-time cached feature_persistent parameter */
+	unsigned int feature_persistent_parm:1;
+	/* Persistent grants feature negotiation result */
 	unsigned int feature_persistent:1;
+	unsigned int bounce:1;
 	unsigned int discard_granularity;
 	unsigned int discard_alignment;
 	/* Number of 4KB segments handled */
@@ -310,8 +319,8 @@
 		if (!gnt_list_entry)
 			goto out_of_memory;
 
-		if (info->feature_persistent) {
-			granted_page = alloc_page(GFP_NOIO);
+		if (info->bounce) {
+			granted_page = alloc_page(GFP_NOIO | __GFP_ZERO);
 			if (!granted_page) {
 				kfree(gnt_list_entry);
 				goto out_of_memory;
@@ -330,7 +339,7 @@
 	list_for_each_entry_safe(gnt_list_entry, n,
 	                         &rinfo->grants, node) {
 		list_del(&gnt_list_entry->node);
-		if (info->feature_persistent)
+		if (info->bounce)
 			__free_page(gnt_list_entry->page);
 		kfree(gnt_list_entry);
 		i--;
@@ -376,7 +385,7 @@
 	/* Assign a gref to this page */
 	gnt_list_entry->gref = gnttab_claim_grant_reference(gref_head);
 	BUG_ON(gnt_list_entry->gref == -ENOSPC);
-	if (info->feature_persistent)
+	if (info->bounce)
 		grant_foreign_access(gnt_list_entry, info);
 	else {
 		/* Grant access to the GFN passed by the caller */
@@ -400,7 +409,7 @@
 	/* Assign a gref to this page */
 	gnt_list_entry->gref = gnttab_claim_grant_reference(gref_head);
 	BUG_ON(gnt_list_entry->gref == -ENOSPC);
-	if (!info->feature_persistent) {
+	if (!info->bounce) {
 		struct page *indirect_page;
 
 		/* Fetch a pre-allocated page to use for indirect grefs */
@@ -702,7 +711,7 @@
 		.grant_idx = 0,
 		.segments = NULL,
 		.rinfo = rinfo,
-		.need_copy = rq_data_dir(req) && info->feature_persistent,
+		.need_copy = rq_data_dir(req) && info->bounce,
 	};
 
 	/*
@@ -771,7 +780,8 @@
 		ring_req->u.rw.handle = info->handle;
 		ring_req->operation = rq_data_dir(req) ?
 			BLKIF_OP_WRITE : BLKIF_OP_READ;
-		if (req_op(req) == REQ_OP_FLUSH || req->cmd_flags & REQ_FUA) {
+		if (req_op(req) == REQ_OP_FLUSH ||
+		    (req_op(req) == REQ_OP_WRITE && (req->cmd_flags & REQ_FUA))) {
 			/*
 			 * Ideally we can do an unordered flush-to-disk.
 			 * In case the backend onlysupports barriers, use that.
@@ -980,11 +990,12 @@
 {
 	blk_queue_write_cache(info->rq, info->feature_flush ? true : false,
 			      info->feature_fua ? true : false);
-	pr_info("blkfront: %s: %s %s %s %s %s\n",
+	pr_info("blkfront: %s: %s %s %s %s %s %s %s\n",
 		info->gd->disk_name, flush_info(info),
 		"persistent grants:", info->feature_persistent ?
 		"enabled;" : "disabled;", "indirect descriptors:",
-		info->max_indirect_segments ? "enabled;" : "disabled;");
+		info->max_indirect_segments ? "enabled;" : "disabled;",
+		"bounce buffer:", info->bounce ? "enabled" : "disabled;");
 }
 
 static int xen_translate_vdev(int vdevice, int *minor, unsigned int *offset)
@@ -1211,7 +1222,7 @@
 	if (!list_empty(&rinfo->indirect_pages)) {
 		struct page *indirect_page, *n;
 
-		BUG_ON(info->feature_persistent);
+		BUG_ON(info->bounce);
 		list_for_each_entry_safe(indirect_page, n, &rinfo->indirect_pages, lru) {
 			list_del(&indirect_page->lru);
 			__free_page(indirect_page);
@@ -1228,7 +1239,7 @@
 							  0, 0UL);
 				rinfo->persistent_gnts_c--;
 			}
-			if (info->feature_persistent)
+			if (info->bounce)
 				__free_page(persistent_gnt->page);
 			kfree(persistent_gnt);
 		}
@@ -1249,7 +1260,7 @@
 		for (j = 0; j < segs; j++) {
 			persistent_gnt = rinfo->shadow[i].grants_used[j];
 			gnttab_end_foreign_access(persistent_gnt->gref, 0, 0UL);
-			if (info->feature_persistent)
+			if (info->bounce)
 				__free_page(persistent_gnt->page);
 			kfree(persistent_gnt);
 		}
@@ -1290,7 +1301,8 @@
 			rinfo->ring_ref[i] = GRANT_INVALID_REF;
 		}
 	}
-	free_pages((unsigned long)rinfo->ring.sring, get_order(info->nr_ring_pages * XEN_PAGE_SIZE));
+	free_pages_exact(rinfo->ring.sring,
+			 info->nr_ring_pages * XEN_PAGE_SIZE);
 	rinfo->ring.sring = NULL;
 
 	if (rinfo->irq)
@@ -1374,9 +1386,15 @@
 	return BLKIF_RSP_OKAY;
 }
 
-static bool blkif_completion(unsigned long *id,
-			     struct blkfront_ring_info *rinfo,
-			     struct blkif_response *bret)
+/*
+ * Return values:
+ *  1 response processed.
+ *  0 missing further responses.
+ * -1 error while processing.
+ */
+static int blkif_completion(unsigned long *id,
+			    struct blkfront_ring_info *rinfo,
+			    struct blkif_response *bret)
 {
 	int i = 0;
 	struct scatterlist *sg;
@@ -1399,7 +1417,7 @@
 
 		/* Wait the second response if not yet here. */
 		if (s2->status < REQ_DONE)
-			return false;
+			return 0;
 
 		bret->status = blkif_get_final_status(s->status,
 						      s2->status);
@@ -1432,7 +1450,7 @@
 	data.s = s;
 	num_sg = s->num_sg;
 
-	if (bret->operation == BLKIF_OP_READ && info->feature_persistent) {
+	if (bret->operation == BLKIF_OP_READ && info->bounce) {
 		for_each_sg(s->sg, sg, num_sg, i) {
 			BUG_ON(sg->offset + sg->length > PAGE_SIZE);
 
@@ -1450,47 +1468,48 @@
 	}
 	/* Add the persistent grant into the list of free grants */
 	for (i = 0; i < num_grant; i++) {
-		if (gnttab_query_foreign_access(s->grants_used[i]->gref)) {
+		if (!gnttab_try_end_foreign_access(s->grants_used[i]->gref)) {
 			/*
 			 * If the grant is still mapped by the backend (the
 			 * backend has chosen to make this grant persistent)
 			 * we add it at the head of the list, so it will be
 			 * reused first.
 			 */
-			if (!info->feature_persistent)
-				pr_alert_ratelimited("backed has not unmapped grant: %u\n",
-						     s->grants_used[i]->gref);
+			if (!info->feature_persistent) {
+				pr_alert("backed has not unmapped grant: %u\n",
+					 s->grants_used[i]->gref);
+				return -1;
+			}
 			list_add(&s->grants_used[i]->node, &rinfo->grants);
 			rinfo->persistent_gnts_c++;
 		} else {
 			/*
-			 * If the grant is not mapped by the backend we end the
-			 * foreign access and add it to the tail of the list,
-			 * so it will not be picked again unless we run out of
-			 * persistent grants.
+			 * If the grant is not mapped by the backend we add it
+			 * to the tail of the list, so it will not be picked
+			 * again unless we run out of persistent grants.
 			 */
-			gnttab_end_foreign_access(s->grants_used[i]->gref, 0, 0UL);
 			s->grants_used[i]->gref = GRANT_INVALID_REF;
 			list_add_tail(&s->grants_used[i]->node, &rinfo->grants);
 		}
 	}
 	if (s->req.operation == BLKIF_OP_INDIRECT) {
 		for (i = 0; i < INDIRECT_GREFS(num_grant); i++) {
-			if (gnttab_query_foreign_access(s->indirect_grants[i]->gref)) {
-				if (!info->feature_persistent)
-					pr_alert_ratelimited("backed has not unmapped grant: %u\n",
-							     s->indirect_grants[i]->gref);
+			if (!gnttab_try_end_foreign_access(s->indirect_grants[i]->gref)) {
+				if (!info->feature_persistent) {
+					pr_alert("backed has not unmapped grant: %u\n",
+						 s->indirect_grants[i]->gref);
+					return -1;
+				}
 				list_add(&s->indirect_grants[i]->node, &rinfo->grants);
 				rinfo->persistent_gnts_c++;
 			} else {
 				struct page *indirect_page;
 
-				gnttab_end_foreign_access(s->indirect_grants[i]->gref, 0, 0UL);
 				/*
 				 * Add the used indirect page back to the list of
 				 * available pages for indirect grefs.
 				 */
-				if (!info->feature_persistent) {
+				if (!info->bounce) {
 					indirect_page = s->indirect_grants[i]->page;
 					list_add(&indirect_page->lru, &rinfo->indirect_pages);
 				}
@@ -1500,7 +1519,7 @@
 		}
 	}
 
-	return true;
+	return 1;
 }
 
 static irqreturn_t blkif_interrupt(int irq, void *dev_id)
@@ -1511,9 +1530,12 @@
 	unsigned long flags;
 	struct blkfront_ring_info *rinfo = (struct blkfront_ring_info *)dev_id;
 	struct blkfront_info *info = rinfo->dev_info;
+	unsigned int eoiflag = XEN_EOI_FLAG_SPURIOUS;
 
-	if (unlikely(info->connected != BLKIF_STATE_CONNECTED))
+	if (unlikely(info->connected != BLKIF_STATE_CONNECTED)) {
+		xen_irq_lateeoi(irq, XEN_EOI_FLAG_SPURIOUS);
 		return IRQ_HANDLED;
+	}
 
 	spin_lock_irqsave(&rinfo->ring_lock, flags);
  again:
@@ -1529,6 +1551,8 @@
 		unsigned long id;
 		unsigned int op;
 
+		eoiflag = 0;
+
 		RING_COPY_RESPONSE(&rinfo->ring, i, &bret);
 		id = bret.id;
 
@@ -1561,12 +1585,17 @@
 		}
 
 		if (bret.operation != BLKIF_OP_DISCARD) {
+			int ret;
+
 			/*
 			 * We may need to wait for an extra response if the
 			 * I/O request is split in 2
 			 */
-			if (!blkif_completion(&id, rinfo, &bret))
+			ret = blkif_completion(&id, rinfo, &bret);
+			if (!ret)
 				continue;
+			if (unlikely(ret < 0))
+				goto err;
 		}
 
 		if (add_id_to_freelist(rinfo, id)) {
@@ -1645,6 +1674,8 @@
 
 	spin_unlock_irqrestore(&rinfo->ring_lock, flags);
 
+	xen_irq_lateeoi(irq, eoiflag);
+
 	return IRQ_HANDLED;
 
  err:
@@ -1652,6 +1683,8 @@
 
 	spin_unlock_irqrestore(&rinfo->ring_lock, flags);
 
+	/* No EOI in order to avoid further interrupts. */
+
 	pr_alert("%s disabled for further use\n", info->gd->disk_name);
 	return IRQ_HANDLED;
 }
@@ -1669,8 +1702,7 @@
 	for (i = 0; i < info->nr_ring_pages; i++)
 		rinfo->ring_ref[i] = GRANT_INVALID_REF;
 
-	sring = (struct blkif_sring *)__get_free_pages(GFP_NOIO | __GFP_HIGH,
-						       get_order(ring_size));
+	sring = alloc_pages_exact(ring_size, GFP_NOIO | __GFP_ZERO);
 	if (!sring) {
 		xenbus_dev_fatal(dev, -ENOMEM, "allocating shared ring");
 		return -ENOMEM;
@@ -1680,7 +1712,7 @@
 
 	err = xenbus_grant_ring(dev, rinfo->ring.sring, info->nr_ring_pages, gref);
 	if (err < 0) {
-		free_pages((unsigned long)sring, get_order(ring_size));
+		free_pages_exact(sring, ring_size);
 		rinfo->ring.sring = NULL;
 		goto fail;
 	}
@@ -1691,8 +1723,8 @@
 	if (err)
 		goto fail;
 
-	err = bind_evtchn_to_irqhandler(rinfo->evtchn, blkif_interrupt, 0,
-					"blkif", rinfo);
+	err = bind_evtchn_to_irqhandler_lateeoi(rinfo->evtchn, blkif_interrupt,
+						0, "blkif", rinfo);
 	if (err <= 0) {
 		xenbus_dev_fatal(dev, err,
 				 "bind_evtchn_to_irqhandler failed");
@@ -1754,6 +1786,12 @@
 	return err;
 }
 
+/* Enable the persistent grants feature. */
+static bool feature_persistent = true;
+module_param(feature_persistent, bool, 0644);
+MODULE_PARM_DESC(feature_persistent,
+		"Enables the persistent grants feature");
+
 /* Common code used when first setting up, and when resuming. */
 static int talk_to_blkback(struct xenbus_device *dev,
 			   struct blkfront_info *info)
@@ -1768,6 +1806,10 @@
 	if (!info)
 		return -ENODEV;
 
+	/* Check if backend is trusted. */
+	info->bounce = !xen_blkif_trusted ||
+		       !xenbus_read_unsigned(dev->nodename, "trusted", 1);
+
 	max_page_order = xenbus_read_unsigned(info->xbdev->otherend,
 					      "max-ring-page-order", 0);
 	ring_page_order = min(xen_blkif_max_ring_order, max_page_order);
@@ -1841,8 +1883,9 @@
 		message = "writing protocol";
 		goto abort_transaction;
 	}
+	info->feature_persistent_parm = feature_persistent;
 	err = xenbus_printf(xbt, dev->nodename, "feature-persistent", "%u",
-			info->feature_persistent);
+			info->feature_persistent_parm);
 	if (err)
 		dev_warn(&dev->dev,
 			 "writing persistent grants feature to xenbus");
@@ -1910,12 +1953,6 @@
 	return 0;
 }
 
-/* Enable the persistent grants feature. */
-static bool feature_persistent = true;
-module_param(feature_persistent, bool, 0644);
-MODULE_PARM_DESC(feature_persistent,
-		"Enables the persistent grants feature");
-
 /*
  * Entry point to this code when a new device is created.  Allocate the basic
  * structures and the ring buffer for communication with the backend, and
@@ -1982,8 +2019,6 @@
 	info->vdevice = vdevice;
 	info->connected = BLKIF_STATE_DISCONNECTED;
 
-	info->feature_persistent = feature_persistent;
-
 	/* Front end dir is a number, which is used as the id. */
 	info->handle = simple_strtoul(strrchr(dev->nodename, '/')+1, NULL, 0);
 	dev_set_drvdata(&dev->dev, info);
@@ -2118,9 +2153,11 @@
 		return;
 
 	/* No more blkif_request(). */
-	blk_mq_stop_hw_queues(info->rq);
-	blk_set_queue_dying(info->rq);
-	set_capacity(info->gd, 0);
+	if (info->rq && info->gd) {
+		blk_mq_stop_hw_queues(info->rq);
+		blk_mark_disk_dead(info->gd);
+		set_capacity(info->gd, 0);
+	}
 
 	for_each_rinfo(info, rinfo, i) {
 		/* No more gnttab callback work. */
@@ -2175,17 +2212,18 @@
 	if (err)
 		goto out_of_memory;
 
-	if (!info->feature_persistent && info->max_indirect_segments) {
+	if (!info->bounce && info->max_indirect_segments) {
 		/*
-		 * We are using indirect descriptors but not persistent
-		 * grants, we need to allocate a set of pages that can be
+		 * We are using indirect descriptors but don't have a bounce
+		 * buffer, we need to allocate a set of pages that can be
 		 * used for mapping indirect grefs
 		 */
 		int num = INDIRECT_GREFS(grants) * BLK_RING_SIZE(info);
 
 		BUG_ON(!list_empty(&rinfo->indirect_pages));
 		for (i = 0; i < num; i++) {
-			struct page *indirect_page = alloc_page(GFP_KERNEL);
+			struct page *indirect_page = alloc_page(GFP_KERNEL |
+			                                        __GFP_ZERO);
 			if (!indirect_page)
 				goto out_of_memory;
 			list_add(&indirect_page->lru, &rinfo->indirect_pages);
@@ -2274,10 +2312,12 @@
 	if (xenbus_read_unsigned(info->xbdev->otherend, "feature-discard", 0))
 		blkfront_setup_discard(info);
 
-	if (info->feature_persistent)
+	if (info->feature_persistent_parm)
 		info->feature_persistent =
 			!!xenbus_read_unsigned(info->xbdev->otherend,
 					       "feature-persistent", 0);
+	if (info->feature_persistent)
+		info->bounce = true;
 
 	indirect_segments = xenbus_read_unsigned(info->xbdev->otherend,
 					"feature-max-indirect-segments", 0);
@@ -2456,16 +2496,19 @@
 
 	dev_dbg(&xbdev->dev, "%s removed", xbdev->nodename);
 
-	del_gendisk(info->gd);
+	if (info->gd)
+		del_gendisk(info->gd);
 
 	mutex_lock(&blkfront_mutex);
 	list_del(&info->info_list);
 	mutex_unlock(&blkfront_mutex);
 
 	blkif_free(info, 0);
-	xlbd_release_minors(info->gd->first_minor, info->gd->minors);
-	blk_cleanup_disk(info->gd);
-	blk_mq_free_tag_set(&info->tag_set);
+	if (info->gd) {
+		xlbd_release_minors(info->gd->first_minor, info->gd->minors);
+		blk_cleanup_disk(info->gd);
+		blk_mq_free_tag_set(&info->tag_set);
+	}
 
 	kfree(info);
 	return 0;
@@ -2520,11 +2563,10 @@
 		list_for_each_entry_safe(gnt_list_entry, tmp, &rinfo->grants,
 					 node) {
 			if (gnt_list_entry->gref == GRANT_INVALID_REF ||
-			    gnttab_query_foreign_access(gnt_list_entry->gref))
+			    !gnttab_try_end_foreign_access(gnt_list_entry->gref))
 				continue;
 
 			list_del(&gnt_list_entry->node);
-			gnttab_end_foreign_access(gnt_list_entry->gref, 0, 0UL);
 			rinfo->persistent_gnts_c--;
 			gnt_list_entry->gref = GRANT_INVALID_REF;
 			list_add_tail(&gnt_list_entry->node, &rinfo->grants);
@@ -2539,6 +2581,13 @@
 	struct blkfront_info *info;
 	bool need_schedule_work = false;
 
+	/*
+	 * Note that when using bounce buffers but not persistent grants
+	 * there's no need to run blkfront_delay_work because grants are
+	 * revoked in blkif_completion or else an error is reported and the
+	 * connection is closed.
+	 */
+
 	mutex_lock(&blkfront_mutex);
 
 	list_for_each_entry(info, &info_list, info_list) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/zram/zcomp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/zram/zcomp.c
@@ -63,12 +63,6 @@
 
 bool zcomp_available_algorithm(const char *comp)
 {
-	int i;
-
-	i = sysfs_match_string(backends, comp);
-	if (i >= 0)
-		return true;
-
 	/*
 	 * Crypto does not ignore a trailing new line symbol,
 	 * so make sure you don't supply a string containing
@@ -217,6 +211,11 @@
 	struct zcomp *comp;
 	int error;
 
+	/*
+	 * Crypto API will execute /sbin/modprobe if the compression module
+	 * is not loaded yet. We must do it here, otherwise we are about to
+	 * call /sbin/modprobe under CPU hot-plug lock.
+	 */
 	if (!zcomp_available_algorithm(compress))
 		return ERR_PTR(-EINVAL);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/block/zram/zram_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/block/zram/zram_drv.c
@@ -499,6 +499,12 @@
 	}
 
 	nr_pages = i_size_read(inode) >> PAGE_SHIFT;
+	/* Refuse to use zero sized device (also prevents self reference) */
+	if (!nr_pages) {
+		err = -EINVAL;
+		goto out;
+	}
+
 	bitmap_sz = BITS_TO_LONGS(nr_pages) * sizeof(long);
 	bitmap = kvzalloc(bitmap_sz, GFP_KERNEL);
 	if (!bitmap) {
@@ -910,7 +916,7 @@
 			zram_test_flag(zram, index, ZRAM_HUGE) ? 'h' : '.',
 			zram_test_flag(zram, index, ZRAM_IDLE) ? 'i' : '.');
 
-		if (count < copied) {
+		if (count <= copied) {
 			zram_slot_unlock(zram, index);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/ath3k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/ath3k.c
@@ -3,7 +3,6 @@
  * Copyright (c) 2008-2009 Atheros Communications Inc.
  */
 
-
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -129,7 +128,6 @@
  * for AR3012
  */
 static const struct usb_device_id ath3k_blist_tbl[] = {
-
 	/* Atheros AR3012 with sflash firmware*/
 	{ USB_DEVICE(0x0489, 0xe04e), .driver_info = BTUSB_ATH3012 },
 	{ USB_DEVICE(0x0489, 0xe04d), .driver_info = BTUSB_ATH3012 },
@@ -203,7 +201,7 @@
 #define TIMEGAP_USEC_MAX	100
 
 static int ath3k_load_firmware(struct usb_device *udev,
-				const struct firmware *firmware)
+			       const struct firmware *firmware)
 {
 	u8 *send_buf;
 	int len = 0;
@@ -238,9 +236,9 @@
 		memcpy(send_buf, firmware->data + sent, size);
 
 		err = usb_bulk_msg(udev, pipe, send_buf, size,
-					&len, 3000);
+				   &len, 3000);
 
-		if (err || (len != size)) {
+		if (err || len != size) {
 			ath3k_log_failed_loading(err, len, size, count);
 			goto error;
 		}
@@ -263,7 +261,7 @@
 }
 
 static int ath3k_get_version(struct usb_device *udev,
-			struct ath3k_version *version)
+			     struct ath3k_version *version)
 {
 	return usb_control_msg_recv(udev, 0, ATH3K_GETVERSION,
 				    USB_TYPE_VENDOR | USB_DIR_IN, 0, 0,
@@ -272,7 +270,7 @@
 }
 
 static int ath3k_load_fwfile(struct usb_device *udev,
-		const struct firmware *firmware)
+			     const struct firmware *firmware)
 {
 	u8 *send_buf;
 	int len = 0;
@@ -311,8 +309,8 @@
 		memcpy(send_buf, firmware->data + sent, size);
 
 		err = usb_bulk_msg(udev, pipe, send_buf, size,
-					&len, 3000);
-		if (err || (len != size)) {
+				   &len, 3000);
+		if (err || len != size) {
 			ath3k_log_failed_loading(err, len, size, count);
 			kfree(send_buf);
 			return err;
@@ -426,7 +424,6 @@
 	}
 
 	switch (fw_version.ref_clock) {
-
 	case ATH3K_XTAL_FREQ_26M:
 		clk_value = 26;
 		break;
@@ -442,7 +439,7 @@
 	}
 
 	snprintf(filename, ATH3K_NAME_LEN, "ar3k/ramps_0x%08x_%d%s",
-		le32_to_cpu(fw_version.rom_version), clk_value, ".dfu");
+		 le32_to_cpu(fw_version.rom_version), clk_value, ".dfu");
 
 	ret = request_firmware(&firmware, filename, &udev->dev);
 	if (ret < 0) {
@@ -457,7 +454,7 @@
 }
 
 static int ath3k_probe(struct usb_interface *intf,
-			const struct usb_device_id *id)
+		       const struct usb_device_id *id)
 {
 	const struct firmware *firmware;
 	struct usb_device *udev = interface_to_usbdev(intf);
@@ -506,10 +503,10 @@
 	if (ret < 0) {
 		if (ret == -ENOENT)
 			BT_ERR("Firmware file \"%s\" not found",
-							ATH3K_FIRMWARE);
+			       ATH3K_FIRMWARE);
 		else
 			BT_ERR("Firmware file \"%s\" request failed (err=%d)",
-							ATH3K_FIRMWARE, ret);
+			       ATH3K_FIRMWARE, ret);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/bfusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/bfusb.c
@@ -628,6 +628,9 @@
 	data->bulk_out_ep   = bulk_out_ep->desc.bEndpointAddress;
 	data->bulk_pkt_size = le16_to_cpu(bulk_out_ep->desc.wMaxPacketSize);
 
+	if (!data->bulk_pkt_size)
+		goto done;
+
 	rwlock_init(&data->lock);
 
 	data->reassembly = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btbcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btbcm.c
@@ -6,8 +6,10 @@
  *  Copyright (C) 2015  Intel Corporation
  */
 
+#include <linux/efi.h>
 #include <linux/module.h>
 #include <linux/firmware.h>
+#include <linux/dmi.h>
 #include <asm/unaligned.h>
 
 #include <net/bluetooth/bluetooth.h>
@@ -32,6 +34,43 @@
 /* For kmalloc-ing the fw-name array instead of putting it on the stack */
 typedef char bcm_fw_name[BCM_FW_NAME_LEN];
 
+#ifdef CONFIG_EFI
+static int btbcm_set_bdaddr_from_efi(struct hci_dev *hdev)
+{
+	efi_guid_t guid = EFI_GUID(0x74b00bd9, 0x805a, 0x4d61, 0xb5, 0x1f,
+				   0x43, 0x26, 0x81, 0x23, 0xd1, 0x13);
+	bdaddr_t efi_bdaddr, bdaddr;
+	efi_status_t status;
+	unsigned long len;
+	int ret;
+
+	if (!efi_rt_services_supported(EFI_RT_SUPPORTED_GET_VARIABLE))
+		return -EOPNOTSUPP;
+
+	len = sizeof(efi_bdaddr);
+	status = efi.get_variable(L"BDADDR", &guid, NULL, &len, &efi_bdaddr);
+	if (status != EFI_SUCCESS)
+		return -ENXIO;
+
+	if (len != sizeof(efi_bdaddr))
+		return -EIO;
+
+	baswap(&bdaddr, &efi_bdaddr);
+
+	ret = btbcm_set_bdaddr(hdev, &bdaddr);
+	if (ret)
+		return ret;
+
+	bt_dev_info(hdev, "BCM: Using EFI device address (%pMR)", &bdaddr);
+	return 0;
+}
+#else
+static int btbcm_set_bdaddr_from_efi(struct hci_dev *hdev)
+{
+	return -EOPNOTSUPP;
+}
+#endif
+
 int btbcm_check_bdaddr(struct hci_dev *hdev)
 {
 	struct hci_rp_read_bd_addr *bda;
@@ -85,9 +124,12 @@
 	    !bacmp(&bda->bdaddr, BDADDR_BCM4345C5) ||
 	    !bacmp(&bda->bdaddr, BDADDR_BCM43430A0) ||
 	    !bacmp(&bda->bdaddr, BDADDR_BCM43341B)) {
-		bt_dev_info(hdev, "BCM: Using default device address (%pMR)",
-			    &bda->bdaddr);
-		set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
+		/* Try falling back to BDADDR EFI variable */
+		if (btbcm_set_bdaddr_from_efi(hdev) != 0) {
+			bt_dev_info(hdev, "BCM: Using default device address (%pMR)",
+				    &bda->bdaddr);
+			set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
+		}
 	}
 
 	kfree_skb(skb);
@@ -343,6 +385,52 @@
 	return skb;
 }
 
+static const struct dmi_system_id disable_broken_read_transmit_power[] = {
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro16,1"),
+		},
+	},
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro16,2"),
+		},
+	},
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro16,4"),
+		},
+	},
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookAir8,1"),
+		},
+	},
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookAir8,2"),
+		},
+	},
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "iMac20,1"),
+		},
+	},
+	{
+		 .matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "iMac20,2"),
+		},
+	},
+	{ }
+};
+
 static int btbcm_read_info(struct hci_dev *hdev)
 {
 	struct sk_buff *skb;
@@ -363,6 +451,10 @@
 	bt_dev_info(hdev, "BCM: features 0x%2.2x", skb->data[1]);
 	kfree_skb(skb);
 
+	/* Read DMI and disable broken Read LE Min/Max Tx Power */
+	if (dmi_first_match(disable_broken_read_transmit_power))
+		set_bit(HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, &hdev->quirks);
+
 	return 0;
 }
 
@@ -402,6 +494,8 @@
 	{ 0x6606, "BCM4345C5"	},	/* 003.006.006 */
 	{ 0x230f, "BCM4356A2"	},	/* 001.003.015 */
 	{ 0x220e, "BCM20702A1"  },	/* 001.002.014 */
+	{ 0x420d, "BCM4349B1"	},	/* 002.002.013 */
+	{ 0x420e, "BCM4349B1"	},	/* 002.002.014 */
 	{ 0x4217, "BCM4329B1"   },	/* 002.002.023 */
 	{ 0x6106, "BCM4359C0"	},	/* 003.001.006 */
 	{ 0x4106, "BCM4335A0"	},	/* 002.001.006 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btintel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btintel.c
@@ -411,7 +411,7 @@
 		return PTR_ERR(skb);
 	}
 
-	if (skb->len != sizeof(*ver)) {
+	if (!skb || skb->len != sizeof(*ver)) {
 		bt_dev_err(hdev, "Intel version event size mismatch");
 		kfree_skb(skb);
 		return -EILSEQ;
@@ -2193,8 +2193,15 @@
 	 * As a workaround, send HCI Reset command first which will reset the
 	 * number of completed commands and allow normal command processing
 	 * from now on.
+	 *
+	 * Regarding the INTEL_BROKEN_SHUTDOWN_LED flag, these devices maybe
+	 * in the SW_RFKILL ON state as a workaround of fixing LED issue during
+	 * the shutdown() procedure, and once the device is in SW_RFKILL ON
+	 * state, the only way to exit out of it is sending the HCI_Reset
+	 * command.
 	 */
-	if (btintel_test_flag(hdev, INTEL_BROKEN_INITIAL_NCMD)) {
+	if (btintel_test_flag(hdev, INTEL_BROKEN_INITIAL_NCMD) ||
+	    btintel_test_flag(hdev, INTEL_BROKEN_SHUTDOWN_LED)) {
 		skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL,
 				     HCI_INIT_TIMEOUT);
 		if (IS_ERR(skb)) {
@@ -2256,27 +2263,31 @@
 
 			/* Apply the device specific HCI quirks
 			 *
-			 * WBS for SdP - SdP and Stp have a same hw_varaint but
-			 * different fw_variant
+			 * WBS for SdP - For the Legacy ROM products, only SdP
+			 * supports the WBS. But the version information is not
+			 * enough to use here because the StP2 and SdP have same
+			 * hw_variant and fw_variant. So, this flag is set by
+			 * the transport driver (btusb) based on the HW info
+			 * (idProduct)
 			 */
-			if (ver.hw_variant == 0x08 && ver.fw_variant == 0x22)
+			if (!btintel_test_flag(hdev,
+					       INTEL_ROM_LEGACY_NO_WBS_SUPPORT))
 				set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED,
 					&hdev->quirks);
-
-			/* These devices have an issue with LED which doesn't
-			 * go off immediately during shutdown. Set the flag
-			 * here to send the LED OFF command during shutdown.
-			 */
-			btintel_set_flag(hdev, INTEL_BROKEN_LED);
+			if (ver.hw_variant == 0x08 && ver.fw_variant == 0x22)
+				set_bit(HCI_QUIRK_VALID_LE_STATES,
+					&hdev->quirks);
 
 			err = btintel_legacy_rom_setup(hdev, &ver);
 			break;
 		case 0x0b:      /* SfP */
-		case 0x0c:      /* WsP */
 		case 0x11:      /* JfP */
 		case 0x12:      /* ThP */
 		case 0x13:      /* HrP */
 		case 0x14:      /* CcP */
+			set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
+			fallthrough;
+		case 0x0c:	/* WsP */
 			/* Apply the device specific HCI quirks
 			 *
 			 * All Legacy bootloader devices support WBS
@@ -2284,11 +2295,6 @@
 			set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED,
 				&hdev->quirks);
 
-			/* Valid LE States quirk for JfP/ThP familiy */
-			if (ver.hw_variant == 0x11 || ver.hw_variant == 0x12)
-				set_bit(HCI_QUIRK_VALID_LE_STATES,
-					&hdev->quirks);
-
 			/* Setup MSFT Extension support */
 			btintel_set_msft_opcode(hdev, ver.hw_variant);
 
@@ -2329,10 +2335,14 @@
 	case 0x12:      /* ThP */
 	case 0x13:      /* HrP */
 	case 0x14:      /* CcP */
-		/* Some legacy bootloader devices from JfP supports both old
-		 * and TLV based HCI_Intel_Read_Version command. But we don't
-		 * want to use the TLV based setup routines for those legacy
-		 * bootloader device.
+		/* Some legacy bootloader devices starting from JfP,
+		 * the operational firmware supports both old and TLV based
+		 * HCI_Intel_Read_Version command based on the command
+		 * parameter.
+		 *
+		 * For upgrading firmware case, the TLV based version cannot
+		 * be used because the firmware filename for legacy bootloader
+		 * is based on the old format.
 		 *
 		 * Also, it is not easy to convert TLV based version from the
 		 * legacy version format.
@@ -2343,7 +2353,20 @@
 		 */
 		err = btintel_read_version(hdev, &ver);
 		if (err)
-			return err;
+			break;
+
+		/* Apply the device specific HCI quirks
+		 *
+		 * All Legacy bootloader devices support WBS
+		 */
+		set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
+
+		/* Set Valid LE States quirk */
+		set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
+
+		/* Setup MSFT Extension support */
+		btintel_set_msft_opcode(hdev, ver.hw_variant);
+
 		err = btintel_bootloader_setup(hdev, &ver);
 		break;
 	case 0x17:
@@ -2358,9 +2381,8 @@
 		 */
 		set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
 
-		/* Valid LE States quirk for GfP */
-		if (INTEL_HW_VARIANT(ver_tlv.cnvi_bt) == 0x18)
-			set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
+		/* Apply LE States quirk from solar onwards */
+		set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
 
 		/* Setup MSFT Extension support */
 		btintel_set_msft_opcode(hdev,
@@ -2371,7 +2393,8 @@
 	default:
 		bt_dev_err(hdev, "Unsupported Intel hw variant (%u)",
 			   INTEL_HW_VARIANT(ver_tlv.cnvi_bt));
-		return -EINVAL;
+		err = -EINVAL;
+		break;
 	}
 
 exit_error:
@@ -2399,9 +2422,10 @@
 
 	/* Some platforms have an issue with BT LED when the interface is
 	 * down or BT radio is turned off, which takes 5 seconds to BT LED
-	 * goes off. This command turns off the BT LED immediately.
+	 * goes off. As a workaround, sends HCI_Intel_SW_RFKILL to put the
+	 * device in the RFKILL ON state which turns off the BT LED immediately.
 	 */
-	if (btintel_test_flag(hdev, INTEL_BROKEN_LED)) {
+	if (btintel_test_flag(hdev, INTEL_BROKEN_SHUTDOWN_LED)) {
 		skb = __hci_cmd_sync(hdev, 0xfc3f, 0, NULL, HCI_INIT_TIMEOUT);
 		if (IS_ERR(skb)) {
 			ret = PTR_ERR(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btintel.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btintel.h
@@ -145,8 +145,9 @@
 	INTEL_FIRMWARE_FAILED,
 	INTEL_BOOTING,
 	INTEL_BROKEN_INITIAL_NCMD,
-	INTEL_BROKEN_LED,
+	INTEL_BROKEN_SHUTDOWN_LED,
 	INTEL_ROM_LEGACY,
+	INTEL_ROM_LEGACY_NO_WBS_SUPPORT,
 
 	__INTEL_NUM_FLAGS,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btmrvl_sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btmrvl_sdio.c
@@ -105,7 +105,7 @@
 		} else {
 			ret = devm_request_irq(dev, cfg->irq_bt,
 					       btmrvl_wake_irq_bt,
-					       0, "bt_wake", card);
+					       IRQF_NO_AUTOEN, "bt_wake", card);
 			if (ret) {
 				dev_err(dev,
 					"Failed to request irq_bt %d (%d)\n",
@@ -114,7 +114,6 @@
 
 			/* Configure wakeup (enabled by default) */
 			device_init_wakeup(dev, true);
-			disable_irq(cfg->irq_bt);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btmtksdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btmtksdio.c
@@ -331,6 +331,7 @@
 {
 	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
 	struct hci_event_hdr *hdr = (void *)skb->data;
+	u8 evt = hdr->evt;
 	int err;
 
 	/* Fix up the vendor event id with 0xff for vendor specific instead
@@ -355,7 +356,7 @@
 	if (err < 0)
 		goto err_free_skb;
 
-	if (hdr->evt == HCI_EV_VENDOR) {
+	if (evt == HCI_EV_VENDOR) {
 		if (test_and_clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT,
 				       &bdev->tx_state)) {
 			/* Barrier to sync with other CPUs */
@@ -981,6 +982,8 @@
 	hdev->manufacturer = 70;
 	set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
 
+	sdio_set_drvdata(func, bdev);
+
 	err = hci_register_dev(hdev);
 	if (err < 0) {
 		dev_err(&func->dev, "Can't register HCI device\n");
@@ -988,8 +991,6 @@
 		return err;
 	}
 
-	sdio_set_drvdata(func, bdev);
-
 	/* pm_runtime_enable would be done after the firmware is being
 	 * downloaded because the core layer probably already enables
 	 * runtime PM for this func such as the case host->caps &
@@ -1042,6 +1043,8 @@
 	if (!bdev)
 		return 0;
 
+	sdio_set_host_pm_flags(func, MMC_PM_KEEP_POWER);
+
 	sdio_claim_host(bdev->func);
 
 	sdio_writel(bdev->func, C_FW_OWN_REQ_SET, MTK_REG_CHLPCR, &err);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btmtkuart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btmtkuart.c
@@ -158,8 +158,10 @@
 	int err;
 
 	hlen = sizeof(*hdr) + wmt_params->dlen;
-	if (hlen > 255)
-		return -EINVAL;
+	if (hlen > 255) {
+		err = -EINVAL;
+		goto err_free_skb;
+	}
 
 	hdr = (struct mtk_wmt_hdr *)&wc;
 	hdr->dir = 1;
@@ -173,7 +175,7 @@
 	err = __hci_cmd_send(hdev, 0xfc6f, hlen, &wc);
 	if (err < 0) {
 		clear_bit(BTMTKUART_TX_WAIT_VND_EVT, &bdev->tx_state);
-		return err;
+		goto err_free_skb;
 	}
 
 	/* The vendor specific WMT commands are all answered by a vendor
@@ -190,13 +192,14 @@
 	if (err == -EINTR) {
 		bt_dev_err(hdev, "Execution of wmt command interrupted");
 		clear_bit(BTMTKUART_TX_WAIT_VND_EVT, &bdev->tx_state);
-		return err;
+		goto err_free_skb;
 	}
 
 	if (err) {
 		bt_dev_err(hdev, "Execution of wmt command timed out");
 		clear_bit(BTMTKUART_TX_WAIT_VND_EVT, &bdev->tx_state);
-		return -ETIMEDOUT;
+		err = -ETIMEDOUT;
+		goto err_free_skb;
 	}
 
 	/* Parse and handle the return WMT event */
@@ -468,7 +471,7 @@
 	return data;
 }
 
-static int btmtkuart_recv(struct hci_dev *hdev, const u8 *data, size_t count)
+static void btmtkuart_recv(struct hci_dev *hdev, const u8 *data, size_t count)
 {
 	struct btmtkuart_dev *bdev = hci_get_drvdata(hdev);
 	const unsigned char *p_left = data, *p_h4;
@@ -507,25 +510,20 @@
 			bt_dev_err(bdev->hdev,
 				   "Frame reassembly failed (%d)", err);
 			bdev->rx_skb = NULL;
-			return err;
+			return;
 		}
 
 		sz_left -= sz_h4;
 		p_left += sz_h4;
 	}
-
-	return 0;
 }
 
 static int btmtkuart_receive_buf(struct serdev_device *serdev, const u8 *data,
 				 size_t count)
 {
 	struct btmtkuart_dev *bdev = serdev_device_get_drvdata(serdev);
-	int err;
 
-	err = btmtkuart_recv(bdev->hdev, data, count);
-	if (err < 0)
-		return err;
+	btmtkuart_recv(bdev->hdev, data, count);
 
 	bdev->hdev->stat.byte_rx += count;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btqca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btqca.c
@@ -98,7 +98,8 @@
 {
 	struct sk_buff *skb;
 	struct edl_event_hdr *edl;
-	char cmd, build_label[QCA_FW_BUILD_VER_LEN];
+	char *build_label;
+	char cmd;
 	int build_lbl_len, err = 0;
 
 	bt_dev_dbg(hdev, "QCA read fw build info");
@@ -113,6 +114,11 @@
 		return err;
 	}
 
+	if (skb->len < sizeof(*edl)) {
+		err = -EILSEQ;
+		goto out;
+	}
+
 	edl = (struct edl_event_hdr *)(skb->data);
 	if (!edl) {
 		bt_dev_err(hdev, "QCA read fw build info with no header");
@@ -128,14 +134,27 @@
 		goto out;
 	}
 
+	if (skb->len < sizeof(*edl) + 1) {
+		err = -EILSEQ;
+		goto out;
+	}
+
 	build_lbl_len = edl->data[0];
-	if (build_lbl_len <= QCA_FW_BUILD_VER_LEN - 1) {
-		memcpy(build_label, edl->data + 1, build_lbl_len);
-		*(build_label + build_lbl_len) = '\0';
+
+	if (skb->len < sizeof(*edl) + 1 + build_lbl_len) {
+		err = -EILSEQ;
+		goto out;
+	}
+
+	build_label = kstrndup(&edl->data[1], build_lbl_len, GFP_KERNEL);
+	if (!build_label) {
+		err = -ENOMEM;
+		goto out;
 	}
 
 	hci_set_fw_info(hdev, "%s", build_label);
 
+	kfree(build_label);
 out:
 	kfree_skb(skb);
 	return err;
@@ -160,6 +179,49 @@
 	return 0;
 }
 
+static int qca_read_fw_board_id(struct hci_dev *hdev, u16 *bid)
+{
+	u8 cmd;
+	struct sk_buff *skb;
+	struct edl_event_hdr *edl;
+	int err = 0;
+
+	cmd = EDL_GET_BID_REQ_CMD;
+	skb = __hci_cmd_sync_ev(hdev, EDL_PATCH_CMD_OPCODE, EDL_PATCH_CMD_LEN,
+				&cmd, 0, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		err = PTR_ERR(skb);
+		bt_dev_err(hdev, "Reading QCA board ID failed (%d)", err);
+		return err;
+	}
+
+	edl = skb_pull_data(skb, sizeof(*edl));
+	if (!edl) {
+		bt_dev_err(hdev, "QCA read board ID with no header");
+		err = -EILSEQ;
+		goto out;
+	}
+
+	if (edl->cresp != EDL_CMD_REQ_RES_EVT ||
+	    edl->rtype != EDL_GET_BID_REQ_CMD) {
+		bt_dev_err(hdev, "QCA Wrong packet: %d %d", edl->cresp, edl->rtype);
+		err = -EIO;
+		goto out;
+	}
+
+	if (skb->len < 3) {
+		err = -EILSEQ;
+		goto out;
+	}
+
+	*bid = (edl->data[1] << 8) + edl->data[2];
+	bt_dev_dbg(hdev, "%s: bid = %x", __func__, *bid);
+
+out:
+	kfree_skb(skb);
+	return err;
+}
+
 int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
 {
 	struct sk_buff *skb;
@@ -182,9 +244,10 @@
 }
 EXPORT_SYMBOL_GPL(qca_send_pre_shutdown_cmd);
 
-static void qca_tlv_check_data(struct hci_dev *hdev,
+static int qca_tlv_check_data(struct hci_dev *hdev,
 			       struct qca_fw_config *config,
-		u8 *fw_data, enum qca_btsoc_type soc_type)
+			       u8 *fw_data, size_t fw_size,
+			       enum qca_btsoc_type soc_type)
 {
 	const u8 *data;
 	u32 type_len;
@@ -194,12 +257,16 @@
 	struct tlv_type_patch *tlv_patch;
 	struct tlv_type_nvm *tlv_nvm;
 	uint8_t nvm_baud_rate = config->user_baud_rate;
+	u8 type;
 
 	config->dnld_mode = QCA_SKIP_EVT_NONE;
 	config->dnld_type = QCA_SKIP_EVT_NONE;
 
 	switch (config->type) {
 	case ELF_TYPE_PATCH:
+		if (fw_size < 7)
+			return -EINVAL;
+
 		config->dnld_mode = QCA_SKIP_EVT_VSE_CC;
 		config->dnld_type = QCA_SKIP_EVT_VSE_CC;
 
@@ -208,6 +275,9 @@
 		bt_dev_dbg(hdev, "File version      : 0x%x", fw_data[6]);
 		break;
 	case TLV_TYPE_PATCH:
+		if (fw_size < sizeof(struct tlv_type_hdr) + sizeof(struct tlv_type_patch))
+			return -EINVAL;
+
 		tlv = (struct tlv_type_hdr *)fw_data;
 		type_len = le32_to_cpu(tlv->type_len);
 		tlv_patch = (struct tlv_type_patch *)tlv->data;
@@ -247,25 +317,56 @@
 		break;
 
 	case TLV_TYPE_NVM:
+		if (fw_size < sizeof(struct tlv_type_hdr))
+			return -EINVAL;
+
 		tlv = (struct tlv_type_hdr *)fw_data;
 
 		type_len = le32_to_cpu(tlv->type_len);
-		length = (type_len >> 8) & 0x00ffffff;
+		length = type_len >> 8;
+		type = type_len & 0xff;
 
-		BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
+		/* Some NVM files have more than one set of tags, only parse
+		 * the first set when it has type 2 for now. When there is
+		 * more than one set there is an enclosing header of type 4.
+		 */
+		if (type == 4) {
+			if (fw_size < 2 * sizeof(struct tlv_type_hdr))
+				return -EINVAL;
+
+			tlv++;
+
+			type_len = le32_to_cpu(tlv->type_len);
+			length = type_len >> 8;
+			type = type_len & 0xff;
+		}
+
+		BT_DBG("TLV Type\t\t : 0x%x", type);
 		BT_DBG("Length\t\t : %d bytes", length);
 
+		if (type != 2)
+			break;
+
+		if (fw_size < length + (tlv->data - fw_data))
+			return -EINVAL;
+
 		idx = 0;
 		data = tlv->data;
-		while (idx < length) {
+		while (idx < length - sizeof(struct tlv_type_nvm)) {
 			tlv_nvm = (struct tlv_type_nvm *)(data + idx);
 
 			tag_id = le16_to_cpu(tlv_nvm->tag_id);
 			tag_len = le16_to_cpu(tlv_nvm->tag_len);
 
+			if (length < idx + sizeof(struct tlv_type_nvm) + tag_len)
+				return -EINVAL;
+
 			/* Update NVM tags as needed */
 			switch (tag_id) {
 			case EDL_TAG_ID_HCI:
+				if (tag_len < 3)
+					return -EINVAL;
+
 				/* HCI transport layer parameters
 				 * enabling software inband sleep
 				 * onto controller side.
@@ -281,6 +382,9 @@
 				break;
 
 			case EDL_TAG_ID_DEEP_SLEEP:
+				if (tag_len < 1)
+					return -EINVAL;
+
 				/* Sleep enable mask
 				 * enabling deep sleep feature on controller.
 				 */
@@ -289,14 +393,16 @@
 				break;
 			}
 
-			idx += (sizeof(u16) + sizeof(u16) + 8 + tag_len);
+			idx += sizeof(struct tlv_type_nvm) + tag_len;
 		}
 		break;
 
 	default:
 		BT_ERR("Unknown TLV type %d", config->type);
-		break;
+		return -EINVAL;
 	}
+
+	return 0;
 }
 
 static int qca_tlv_send_segment(struct hci_dev *hdev, int seg_size,
@@ -446,7 +552,9 @@
 	memcpy(data, fw->data, size);
 	release_firmware(fw);
 
-	qca_tlv_check_data(hdev, config, data, soc_type);
+	ret = qca_tlv_check_data(hdev, config, data, size, soc_type);
+	if (ret)
+		goto out;
 
 	segment = data;
 	remain = size;
@@ -529,6 +637,23 @@
 }
 EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
 
+static void qca_generate_hsp_nvm_name(char *fwname, size_t max_size,
+		struct qca_btsoc_version ver, u8 rom_ver, u16 bid)
+{
+	const char *variant;
+
+	/* hsp gf chip */
+	if ((le32_to_cpu(ver.soc_id) & QCA_HSP_GF_SOC_MASK) == QCA_HSP_GF_SOC_ID)
+		variant = "g";
+	else
+		variant = "";
+
+	if (bid == 0x0)
+		snprintf(fwname, max_size, "qca/hpnv%02x%s.bin", rom_ver, variant);
+	else
+		snprintf(fwname, max_size, "qca/hpnv%02x%s.%x", rom_ver, variant, bid);
+}
+
 int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		   enum qca_btsoc_type soc_type, struct qca_btsoc_version ver,
 		   const char *firmware_name)
@@ -537,6 +662,7 @@
 	int err;
 	u8 rom_ver = 0;
 	u32 soc_ver;
+	u16 boardid = 0;
 
 	bt_dev_dbg(hdev, "QCA setup on UART");
 
@@ -549,24 +675,45 @@
 	/* Firmware files to download are based on ROM version.
 	 * ROM version is derived from last two bytes of soc_ver.
 	 */
-	rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
+	if (soc_type == QCA_WCN3988)
+		rom_ver = ((soc_ver & 0x00000f00) >> 0x05) | (soc_ver & 0x0000000f);
+	else
+		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
 
 	/* Download rampatch file */
 	config.type = TLV_TYPE_PATCH;
-	if (qca_is_wcn399x(soc_type)) {
+	switch (soc_type) {
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/crbtfw%02x.tlv", rom_ver);
-	} else if (soc_type == QCA_QCA6390) {
+		break;
+	case QCA_WCN3988:
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/apbtfw%02x.tlv", rom_ver);
+		break;
+	case QCA_QCA2066:
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/hpbtfw%02x.tlv", rom_ver);
+		break;
+	case QCA_QCA6390:
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/htbtfw%02x.tlv", rom_ver);
-	} else if (soc_type == QCA_WCN6750) {
+		break;
+	case QCA_WCN6750:
 		/* Choose mbn file by default.If mbn file is not found
 		 * then choose tlv file
 		 */
 		config.type = ELF_TYPE_PATCH;
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/msbtfw%02x.mbn", rom_ver);
-	} else {
+		break;
+	case QCA_WCN6855:
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/hpbtfw%02x.tlv", rom_ver);
+		break;
+	default:
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/rampatch_%08x.bin", soc_ver);
 	}
@@ -580,29 +727,53 @@
 	/* Give the controller some time to get ready to receive the NVM */
 	msleep(10);
 
+	if (soc_type == QCA_QCA2066)
+		qca_read_fw_board_id(hdev, &boardid);
+
 	/* Download NVM configuration */
 	config.type = TLV_TYPE_NVM;
-	if (firmware_name)
+	if (firmware_name) {
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/%s", firmware_name);
-	else if (qca_is_wcn399x(soc_type)) {
-		if (ver.soc_id == QCA_WCN3991_SOC_ID) {
+	} else {
+		switch (soc_type) {
+		case QCA_WCN3990:
+		case QCA_WCN3991:
+		case QCA_WCN3998:
+			if (le32_to_cpu(ver.soc_id) == QCA_WCN3991_SOC_ID) {
+				snprintf(config.fwname, sizeof(config.fwname),
+					 "qca/crnv%02xu.bin", rom_ver);
+			} else {
+				snprintf(config.fwname, sizeof(config.fwname),
+					 "qca/crnv%02x.bin", rom_ver);
+			}
+			break;
+		case QCA_WCN3988:
 			snprintf(config.fwname, sizeof(config.fwname),
-				 "qca/crnv%02xu.bin", rom_ver);
-		} else {
+				 "qca/apnv%02x.bin", rom_ver);
+			break;
+		case QCA_QCA2066:
+			qca_generate_hsp_nvm_name(config.fwname,
+				sizeof(config.fwname), ver, rom_ver, boardid);
+			break;
+		case QCA_QCA6390:
+			snprintf(config.fwname, sizeof(config.fwname),
+				 "qca/htnv%02x.bin", rom_ver);
+			break;
+		case QCA_WCN6750:
 			snprintf(config.fwname, sizeof(config.fwname),
-				 "qca/crnv%02x.bin", rom_ver);
+				 "qca/msnv%02x.bin", rom_ver);
+			break;
+		case QCA_WCN6855:
+			snprintf(config.fwname, sizeof(config.fwname),
+				 "qca/hpnv%02x.bin", rom_ver);
+			break;
+
+		default:
+			snprintf(config.fwname, sizeof(config.fwname),
+				 "qca/nvm_%08x.bin", soc_ver);
 		}
 	}
-	else if (soc_type == QCA_QCA6390)
-		snprintf(config.fwname, sizeof(config.fwname),
-			 "qca/htnv%02x.bin", rom_ver);
-	else if (soc_type == QCA_WCN6750)
-		snprintf(config.fwname, sizeof(config.fwname),
-			 "qca/msnv%02x.bin", rom_ver);
-	else
-		snprintf(config.fwname, sizeof(config.fwname),
-			 "qca/nvm_%08x.bin", soc_ver);
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
 	if (err < 0) {
@@ -610,16 +781,25 @@
 		return err;
 	}
 
-	if (soc_type >= QCA_WCN3991) {
+	switch (soc_type) {
+	case QCA_WCN3991:
+	case QCA_QCA2066:
+	case QCA_QCA6390:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		err = qca_disable_soc_logging(hdev);
 		if (err < 0)
 			return err;
+		break;
+	default:
+		break;
 	}
 
 	/* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the
 	 * VsMsftOpCode.
 	 */
 	switch (soc_type) {
+	case QCA_WCN3988:
 	case QCA_WCN3990:
 	case QCA_WCN3991:
 	case QCA_WCN3998:
@@ -637,11 +817,17 @@
 		return err;
 	}
 
-	if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750) {
+	switch (soc_type) {
+	case QCA_WCN3991:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		/* get fw build info */
 		err = qca_read_fw_build_info(hdev);
 		if (err < 0)
 			return err;
+		break;
+	default:
+		break;
 	}
 
 	bt_dev_info(hdev, "QCA setup on UART is completed");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btqca.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btqca.h
@@ -12,6 +12,7 @@
 #define EDL_PATCH_VER_REQ_CMD		(0x19)
 #define EDL_PATCH_TLV_REQ_CMD		(0x1E)
 #define EDL_GET_BUILD_INFO_CMD		(0x20)
+#define EDL_GET_BID_REQ_CMD			(0x23)
 #define EDL_NVM_ACCESS_SET_REQ_CMD	(0x01)
 #define MAX_SIZE_PER_TLV_SEGMENT	(243)
 #define QCA_PRE_SHUTDOWN_CMD		(0xFC08)
@@ -44,8 +45,8 @@
 #define get_soc_ver(soc_id, rom_ver)	\
 	((le32_to_cpu(soc_id) << 16) | (le16_to_cpu(rom_ver)))
 
-#define QCA_FW_BUILD_VER_LEN		255
-
+#define QCA_HSP_GF_SOC_ID			0x1200
+#define QCA_HSP_GF_SOC_MASK			0x0000ff00
 
 enum qca_baudrate {
 	QCA_BAUDRATE_115200 	= 0,
@@ -140,11 +141,14 @@
 	QCA_INVALID = -1,
 	QCA_AR3002,
 	QCA_ROME,
+	QCA_WCN3988,
 	QCA_WCN3990,
 	QCA_WCN3998,
 	QCA_WCN3991,
+	QCA_QCA2066,
 	QCA_QCA6390,
 	QCA_WCN6750,
+	QCA_WCN6855,
 };
 
 #if IS_ENABLED(CONFIG_BT_QCA)
@@ -157,16 +161,6 @@
 			 enum qca_btsoc_type);
 int qca_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr);
 int qca_send_pre_shutdown_cmd(struct hci_dev *hdev);
-static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
-{
-	return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
-	       soc_type == QCA_WCN3998;
-}
-static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
-{
-	return soc_type == QCA_WCN6750;
-}
-
 #else
 
 static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
@@ -194,16 +188,6 @@
 	return -EOPNOTSUPP;
 }
 
-static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
-{
-	return false;
-}
-
-static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
-{
-	return false;
-}
-
 static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
 {
 	return -EOPNOTSUPP;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btqcomsmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btqcomsmd.c
@@ -122,6 +122,21 @@
 	return 0;
 }
 
+static int btqcomsmd_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr)
+{
+	int ret;
+
+	ret = qca_set_bdaddr_rome(hdev, bdaddr);
+	if (ret)
+		return ret;
+
+	/* The firmware stops responding for a while after setting the bdaddr,
+	 * causing timeouts for subsequent commands. Sleep a bit to avoid this.
+	 */
+	usleep_range(1000, 10000);
+	return 0;
+}
+
 static int btqcomsmd_probe(struct platform_device *pdev)
 {
 	struct btqcomsmd *btq;
@@ -162,7 +177,7 @@
 	hdev->close = btqcomsmd_close;
 	hdev->send = btqcomsmd_send;
 	hdev->setup = btqcomsmd_setup;
-	hdev->set_bdaddr = qca_set_bdaddr_rome;
+	hdev->set_bdaddr = btqcomsmd_set_bdaddr;
 
 	ret = hci_register_dev(hdev);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btrtl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btrtl.c
@@ -594,8 +594,10 @@
 	hci_rev = le16_to_cpu(resp->hci_rev);
 	lmp_subver = le16_to_cpu(resp->lmp_subver);
 
-	if (resp->hci_ver == 0x8 && le16_to_cpu(resp->hci_rev) == 0x826c &&
-	    resp->lmp_ver == 0x8 && le16_to_cpu(resp->lmp_subver) == 0xa99e)
+	btrtl_dev->ic_info = btrtl_match_ic(lmp_subver, hci_rev, hci_ver,
+					    hdev->bus);
+
+	if (!btrtl_dev->ic_info)
 		btrtl_dev->drop_fw = true;
 
 	if (btrtl_dev->drop_fw) {
@@ -634,13 +636,13 @@
 		hci_ver = resp->hci_ver;
 		hci_rev = le16_to_cpu(resp->hci_rev);
 		lmp_subver = le16_to_cpu(resp->lmp_subver);
+
+		btrtl_dev->ic_info = btrtl_match_ic(lmp_subver, hci_rev, hci_ver,
+						    hdev->bus);
 	}
 out_free:
 	kfree_skb(skb);
 
-	btrtl_dev->ic_info = btrtl_match_ic(lmp_subver, hci_rev, hci_ver,
-					    hdev->bus);
-
 	if (!btrtl_dev->ic_info) {
 		rtl_dev_info(hdev, "unknown IC info, lmp subver %04x, hci rev %04x, hci ver %04x",
 			    lmp_subver, hci_rev, hci_ver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btsdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btsdio.c
@@ -355,6 +355,7 @@
 	if (!data)
 		return;
 
+	cancel_work_sync(&data->work);
 	hdev = data->hdev;
 
 	sdio_set_drvdata(func, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/btusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/btusb.c
@@ -14,6 +14,7 @@
 #include <linux/iopoll.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
+#include <linux/pci.h>
 #include <linux/suspend.h>
 #include <linux/gpio/consumer.h>
 #include <asm/unaligned.h>
@@ -59,7 +60,9 @@
 #define BTUSB_WIDEBAND_SPEECH	0x400000
 #define BTUSB_VALID_LE_STATES   0x800000
 #define BTUSB_QCA_WCN6855	0x1000000
+#define BTUSB_INTEL_BROKEN_SHUTDOWN_LED	0x2000000
 #define BTUSB_INTEL_BROKEN_INITIAL_NCMD 0x4000000
+#define BTUSB_INTEL_NO_WBS_SUPPORT	0x8000000
 
 static const struct usb_device_id btusb_table[] = {
 	/* Generic Bluetooth USB device */
@@ -295,6 +298,24 @@
 	{ USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 |
 						     BTUSB_WIDEBAND_SPEECH |
 						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0cc), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0d6), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0e3), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x10ab, 0x9309), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x10ab, 0x9409), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0d0), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
 
 	/* Broadcom BCM2035 */
 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
@@ -365,16 +386,25 @@
 	{ USB_DEVICE(0x8087, 0x0033), .driver_info = BTUSB_INTEL_COMBINED },
 	{ USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
 	{ USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL_COMBINED |
-						     BTUSB_INTEL_BROKEN_INITIAL_NCMD },
-	{ USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL_COMBINED },
+						     BTUSB_INTEL_NO_WBS_SUPPORT |
+						     BTUSB_INTEL_BROKEN_INITIAL_NCMD |
+						     BTUSB_INTEL_BROKEN_SHUTDOWN_LED },
+	{ USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL_COMBINED |
+						     BTUSB_INTEL_NO_WBS_SUPPORT |
+						     BTUSB_INTEL_BROKEN_SHUTDOWN_LED },
 	{ USB_DEVICE(0x8087, 0x0a2b), .driver_info = BTUSB_INTEL_COMBINED },
-	{ USB_DEVICE(0x8087, 0x0aa7), .driver_info = BTUSB_INTEL_COMBINED },
+	{ USB_DEVICE(0x8087, 0x0aa7), .driver_info = BTUSB_INTEL_COMBINED |
+						     BTUSB_INTEL_BROKEN_SHUTDOWN_LED },
 	{ USB_DEVICE(0x8087, 0x0aaa), .driver_info = BTUSB_INTEL_COMBINED },
 
 	/* Other Intel Bluetooth devices */
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
 	  .driver_info = BTUSB_IGNORE },
 
+	/* Realtek 8821CE Bluetooth devices */
+	{ USB_DEVICE(0x13d3, 0x3529), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+
 	/* Realtek 8822CE Bluetooth devices */
 	{ USB_DEVICE(0x0bda, 0xb00c), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
@@ -382,8 +412,44 @@
 						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Realtek 8852AE Bluetooth devices */
+	{ USB_DEVICE(0x0bda, 0x2852), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0bda, 0xc852), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0bda, 0x385a), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0bda, 0x4852), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x04c5, 0x165c), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x04ca, 0x4006), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+
+	/* Realtek 8852CE Bluetooth devices */
+	{ USB_DEVICE(0x04ca, 0x4007), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x04c5, 0x1675), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0cb8, 0xc558), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3587), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3586), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+
+	/* Realtek 8852BE Bluetooth devices */
+	{ USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0bda, 0x4853), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0bda, 0x887b), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0bda, 0xb85b), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3570), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3571), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Realtek Bluetooth devices */
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
@@ -404,16 +470,42 @@
 						     BTUSB_VALID_LE_STATES },
 
 	/* Additional MediaTek MT7921 Bluetooth devices */
+	{ USB_DEVICE(0x0489, 0xe0c8), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0cd), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
 	{ USB_DEVICE(0x04ca, 0x3802), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH |
 						     BTUSB_VALID_LE_STATES },
 	{ USB_DEVICE(0x13d3, 0x3563), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH |
 						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x13d3, 0x3564), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x13d3, 0x3567), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
 	{ USB_DEVICE(0x0489, 0xe0cd), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH |
 						     BTUSB_VALID_LE_STATES },
 
+	/* MediaTek MT7922A Bluetooth devices */
+	{ USB_DEVICE(0x0489, 0xe0d8), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0d9), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x0489, 0xe0f5), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+	{ USB_DEVICE(0x13d3, 0x3568), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+
 	/* Additional Realtek 8723AE Bluetooth devices */
 	{ USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
 	{ USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },
@@ -433,9 +525,15 @@
 	{ USB_DEVICE(0x0bda, 0xb009), .driver_info = BTUSB_REALTEK },
 	{ USB_DEVICE(0x2ff8, 0xb011), .driver_info = BTUSB_REALTEK },
 
+	/* Additional Realtek 8761B Bluetooth devices */
+	{ USB_DEVICE(0x2357, 0x0604), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+
 	/* Additional Realtek 8761BU Bluetooth devices */
 	{ USB_DEVICE(0x0b05, 0x190e), .driver_info = BTUSB_REALTEK |
 	  					     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x2550, 0x8761), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Additional Realtek 8821AE Bluetooth devices */
 	{ USB_DEVICE(0x0b05, 0x17dc), .driver_info = BTUSB_REALTEK },
@@ -451,10 +549,6 @@
 	/* Additional Realtek 8822CE Bluetooth devices */
 	{ USB_DEVICE(0x04ca, 0x4005), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
-	/* Bluetooth component of Realtek 8852AE device */
-	{ USB_DEVICE(0x04ca, 0x4006), .driver_info = BTUSB_REALTEK |
-						     BTUSB_WIDEBAND_SPEECH },
-
 	{ USB_DEVICE(0x04c5, 0x161f), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0b05, 0x18ef), .driver_info = BTUSB_REALTEK |
@@ -475,6 +569,10 @@
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0cb5, 0xc547), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3591), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe125), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Silicon Wave based devices */
 	{ USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_SWAVE },
@@ -672,13 +770,13 @@
 
 	spin_lock_irqsave(&data->rxlock, flags);
 
-	kfree_skb(data->evt_skb);
+	dev_kfree_skb_irq(data->evt_skb);
 	data->evt_skb = NULL;
 
-	kfree_skb(data->acl_skb);
+	dev_kfree_skb_irq(data->acl_skb);
 	data->acl_skb = NULL;
 
-	kfree_skb(data->sco_skb);
+	dev_kfree_skb_irq(data->sco_skb);
 	data->sco_skb = NULL;
 
 	spin_unlock_irqrestore(&data->rxlock, flags);
@@ -914,7 +1012,15 @@
 	if (!urb)
 		return -ENOMEM;
 
-	size = le16_to_cpu(data->intr_ep->wMaxPacketSize);
+	if (le16_to_cpu(data->udev->descriptor.idVendor)  == 0x0a12 &&
+	    le16_to_cpu(data->udev->descriptor.idProduct) == 0x0001)
+		/* Fake CSR devices don't seem to support sort-transter */
+		size = le16_to_cpu(data->intr_ep->wMaxPacketSize);
+	else
+		/* Use maximum HCI Event size so the USB stack handles
+		 * ZPL/short-transfer automatically.
+		 */
+		size = HCI_MAX_EVENT_SIZE;
 
 	buf = kmalloc(size, mem_flags);
 	if (!buf) {
@@ -1686,7 +1792,7 @@
 		 * alternate setting.
 		 */
 		spin_lock_irqsave(&data->rxlock, flags);
-		kfree_skb(data->sco_skb);
+		dev_kfree_skb_irq(data->sco_skb);
 		data->sco_skb = NULL;
 		spin_unlock_irqrestore(&data->rxlock, flags);
 
@@ -1838,6 +1944,11 @@
 
 	rp = (struct hci_rp_read_local_version *)skb->data;
 
+	bt_dev_info(hdev, "CSR: Setting up dongle with HCI ver=%u rev=%04x; LMP ver=%u subver=%04x; manufacturer=%u",
+		le16_to_cpu(rp->hci_ver), le16_to_cpu(rp->hci_rev),
+		le16_to_cpu(rp->lmp_ver), le16_to_cpu(rp->lmp_subver),
+		le16_to_cpu(rp->manufacturer));
+
 	/* Detect a wide host of Chinese controllers that aren't CSR.
 	 *
 	 * Known fake bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
@@ -2217,6 +2328,7 @@
 		skb = bt_skb_alloc(HCI_WMT_MAX_EVENT_SIZE, GFP_ATOMIC);
 		if (!skb) {
 			hdev->stat.err_rx++;
+			kfree(urb->setup_packet);
 			return;
 		}
 
@@ -2237,6 +2349,7 @@
 			data->evt_skb = skb_clone(skb, GFP_ATOMIC);
 			if (!data->evt_skb) {
 				kfree_skb(skb);
+				kfree(urb->setup_packet);
 				return;
 			}
 		}
@@ -2245,6 +2358,7 @@
 		if (err < 0) {
 			kfree_skb(data->evt_skb);
 			data->evt_skb = NULL;
+			kfree(urb->setup_packet);
 			return;
 		}
 
@@ -2255,6 +2369,7 @@
 			wake_up_bit(&data->flags,
 				    BTUSB_TX_WAIT_VND_EVT);
 		}
+		kfree(urb->setup_packet);
 		return;
 	} else if (urb->status == -ENOENT) {
 		/* Avoid suspend failed when usb_kill_urb */
@@ -2275,6 +2390,7 @@
 	usb_anchor_urb(urb, &data->ctrl_anchor);
 	err = usb_submit_urb(urb, GFP_ATOMIC);
 	if (err < 0) {
+		kfree(urb->setup_packet);
 		/* -EPERM: urb is being killed;
 		 * -ENODEV: device got disconnected
 		 */
@@ -2367,15 +2483,29 @@
 
 	set_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
 
+	/* WMT cmd/event doesn't follow up the generic HCI cmd/event handling,
+	 * it needs constantly polling control pipe until the host received the
+	 * WMT event, thus, we should require to specifically acquire PM counter
+	 * on the USB to prevent the interface from entering auto suspended
+	 * while WMT cmd/event in progress.
+	 */
+	err = usb_autopm_get_interface(data->intf);
+	if (err < 0)
+		goto err_free_wc;
+
 	err = __hci_cmd_send(hdev, 0xfc6f, hlen, wc);
 
 	if (err < 0) {
 		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
+		usb_autopm_put_interface(data->intf);
 		goto err_free_wc;
 	}
 
 	/* Submit control IN URB on demand to process the WMT event */
 	err = btusb_mtk_submit_wmt_recv_urb(hdev);
+
+	usb_autopm_put_interface(data->intf);
+
 	if (err < 0)
 		goto err_free_wc;
 
@@ -2403,6 +2533,9 @@
 		goto err_free_wc;
 	}
 
+	if (data->evt_skb == NULL)
+		goto err_free_wc;
+
 	/* Parse and handle the return WMT event */
 	wmt_evt = (struct btmtk_hci_wmt_evt *)data->evt_skb->data;
 	if (wmt_evt->whdr.op != hdr->op) {
@@ -2515,6 +2648,7 @@
 				} else {
 					bt_dev_err(hdev, "Failed wmt patch dwnld status (%d)",
 						   status);
+					err = -EIO;
 					goto err_release_fw;
 				}
 			}
@@ -2804,11 +2938,16 @@
 	case 0x7668:
 		fwname = FIRMWARE_MT7668;
 		break;
+	case 0x7922:
 	case 0x7961:
 		snprintf(fw_bin_name, sizeof(fw_bin_name),
 			"mediatek/BT_RAM_CODE_MT%04x_1_%x_hdr.bin",
 			 dev_id & 0xffff, (fw_version & 0xff) + 1);
 		err = btusb_mtk_setup_firmware_79xx(hdev, fw_bin_name);
+		if (err < 0) {
+			bt_dev_err(hdev, "Failed to set up firmware (%d)", err);
+			return err;
+		}
 
 		/* It's Device EndPoint Reset Option Register */
 		btusb_mtk_uhw_reg_write(data, MTK_EP_RST_OPT, MTK_EP_RST_IN_OUT_OPT);
@@ -2828,6 +2967,7 @@
 		}
 
 		hci_set_msft_opcode(hdev, 0xFD30);
+		hci_set_aosp_capable(hdev);
 		goto done;
 	default:
 		bt_dev_err(hdev, "Unsupported hardware variant (%08x)",
@@ -3085,6 +3225,35 @@
 	return 0;
 }
 
+#define BTUSB_EDGE_LED_COMMAND		0xfc77
+
+static void btusb_edge_set_led(struct hci_dev *hdev, bool state)
+{
+	struct sk_buff *skb;
+	u8 config_led[] = { 0x09, 0x00, 0x01, 0x01 };
+
+	if (state)
+		config_led[1] = 0x01;
+
+	skb = __hci_cmd_sync(hdev, BTUSB_EDGE_LED_COMMAND, sizeof(config_led), config_led, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb))
+		BT_ERR("%s fail to set LED (%ld)", hdev->name, PTR_ERR(skb));
+	else
+		kfree_skb(skb);
+}
+
+static int btusb_edge_post_init(struct hci_dev *hdev)
+{
+	btusb_edge_set_led(hdev, true);
+	return 0;
+}
+
+static int btusb_edge_shutdown(struct hci_dev *hdev)
+{
+	btusb_edge_set_led(hdev, false);
+	return 0;
+}
+
 static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev,
 				    const bdaddr_t *bdaddr)
 {
@@ -3140,12 +3309,17 @@
 #define QCA_PATCH_UPDATED	0x80
 #define QCA_DFU_TIMEOUT		3000
 #define QCA_FLAG_MULTI_NVM      0x80
+#define QCA_BT_RESET_WAIT_MS    100
+
+#define WCN6855_2_0_RAM_VERSION_GF 0x400c1200
+#define WCN6855_2_1_RAM_VERSION_GF 0x400c1211
 
 struct qca_version {
 	__le32	rom_version;
 	__le32	patch_version;
 	__le32	ram_version;
-	__le16	board_id;
+	__u8	chip_id;
+	__u8	platform_id;
 	__le16	flag;
 	__u8	reserved[4];
 } __packed;
@@ -3172,6 +3346,7 @@
 	{ 0x00000302, 28, 4, 16 }, /* Rome 3.2 */
 	{ 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
 	{ 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
+	{ 0x00130201, 40, 4, 16 }, /* WCN6855 2.1 */
 };
 
 static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
@@ -3326,6 +3501,50 @@
 	return err;
 }
 
+static void btusb_generate_qca_nvm_name(char *fwname, size_t max_size,
+					const struct qca_version *ver)
+{
+	u32 rom_version = le32_to_cpu(ver->rom_version);
+	u16 flag = le16_to_cpu(ver->flag);
+
+	if (((flag >> 8) & 0xff) == QCA_FLAG_MULTI_NVM) {
+		/* The board_id should be split into two bytes
+		 * The 1st byte is chip ID, and the 2nd byte is platform ID
+		 * For example, board ID 0x010A, 0x01 is platform ID. 0x0A is chip ID
+		 * we have several platforms, and platform IDs are continuously added
+		 * Platform ID:
+		 * 0x00 is for Mobile
+		 * 0x01 is for X86
+		 * 0x02 is for Automotive
+		 * 0x03 is for Consumer electronic
+		 */
+		u16 board_id = (ver->chip_id << 8) + ver->platform_id;
+		const char *variant;
+
+		switch (le32_to_cpu(ver->ram_version)) {
+		case WCN6855_2_0_RAM_VERSION_GF:
+		case WCN6855_2_1_RAM_VERSION_GF:
+			variant = "_gf";
+			break;
+		default:
+			variant = "";
+			break;
+		}
+
+		if (board_id == 0) {
+			snprintf(fwname, max_size, "qca/nvm_usb_%08x%s.bin",
+				rom_version, variant);
+		} else {
+			snprintf(fwname, max_size, "qca/nvm_usb_%08x%s_%04x.bin",
+				rom_version, variant, board_id);
+		}
+	} else {
+		snprintf(fwname, max_size, "qca/nvm_usb_%08x.bin",
+			rom_version);
+	}
+
+}
+
 static int btusb_setup_qca_load_nvm(struct hci_dev *hdev,
 				    struct qca_version *ver,
 				    const struct qca_device_info *info)
@@ -3334,20 +3553,7 @@
 	char fwname[64];
 	int err;
 
-	if (((ver->flag >> 8) & 0xff) == QCA_FLAG_MULTI_NVM) {
-		/* if boardid equal 0, use default nvm without surfix */
-		if (le16_to_cpu(ver->board_id) == 0x0) {
-			snprintf(fwname, sizeof(fwname), "qca/nvm_usb_%08x.bin",
-				 le32_to_cpu(ver->rom_version));
-		} else {
-			snprintf(fwname, sizeof(fwname), "qca/nvm_usb_%08x_%04x.bin",
-				le32_to_cpu(ver->rom_version),
-				le16_to_cpu(ver->board_id));
-		}
-	} else {
-		snprintf(fwname, sizeof(fwname), "qca/nvm_usb_%08x.bin",
-			 le32_to_cpu(ver->rom_version));
-	}
+	btusb_generate_qca_nvm_name(fwname, sizeof(fwname), ver);
 
 	err = request_firmware(&fw, fwname, &hdev->dev);
 	if (err) {
@@ -3430,6 +3636,13 @@
 		err = btusb_setup_qca_load_nvm(hdev, &ver, info);
 		if (err < 0)
 			return err;
+
+		/* WCN6855 2.1 will reset to apply firmware downloaded here, so
+		 * wait ~100ms for reset Done then go ahead, otherwise, it maybe
+		 * cause potential enable failure.
+		 */
+		if (info->rom_version == 0x00130201)
+			msleep(QCA_BT_RESET_WAIT_MS);
 	}
 
 	return 0;
@@ -3806,12 +4019,28 @@
 		hdev->send = btusb_send_frame_intel;
 		hdev->cmd_timeout = btusb_intel_cmd_timeout;
 
+		if (id->driver_info & BTUSB_INTEL_NO_WBS_SUPPORT)
+			btintel_set_flag(hdev, INTEL_ROM_LEGACY_NO_WBS_SUPPORT);
+
 		if (id->driver_info & BTUSB_INTEL_BROKEN_INITIAL_NCMD)
 			btintel_set_flag(hdev, INTEL_BROKEN_INITIAL_NCMD);
+
+		if (id->driver_info & BTUSB_INTEL_BROKEN_SHUTDOWN_LED)
+			btintel_set_flag(hdev, INTEL_BROKEN_SHUTDOWN_LED);
 	}
 
-	if (id->driver_info & BTUSB_MARVELL)
+	if (id->driver_info & BTUSB_MARVELL) {
+		struct pci_dev *pdev;
 		hdev->set_bdaddr = btusb_set_bdaddr_marvell;
+		pdev = pci_get_subsys(PCI_ANY_ID, PCI_ANY_ID, 0x1028, 0x0720, NULL);
+		if (!pdev)
+			pdev = pci_get_subsys(PCI_ANY_ID, PCI_ANY_ID, 0x1028, 0x0733, NULL);
+		if (pdev) {
+			pci_dev_put(pdev);
+			hdev->post_init = btusb_edge_post_init;
+			hdev->shutdown = btusb_edge_shutdown;
+		}
+	}
 
 	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_MTK) &&
 	    (id->driver_info & BTUSB_MEDIATEK)) {
@@ -3842,6 +4071,7 @@
 
 	if (id->driver_info & BTUSB_QCA_ROME) {
 		data->setup_on_usb = btusb_setup_qca;
+		hdev->shutdown = btusb_shutdown_qca;
 		hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
 		hdev->cmd_timeout = btusb_qca_cmd_timeout;
 		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_bcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_bcm.c
@@ -1188,7 +1188,12 @@
 		return -ENOMEM;
 
 	dev->dev = &pdev->dev;
-	dev->irq = platform_get_irq(pdev, 0);
+
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0)
+		return ret;
+
+	dev->irq = ret;
 
 	/* Initialize routing field to an unused value */
 	dev->pcm_int_params[0] = 0xff;
@@ -1510,8 +1515,10 @@
 	{ .compatible = "brcm,bcm4345c5" },
 	{ .compatible = "brcm,bcm4330-bt" },
 	{ .compatible = "brcm,bcm43438-bt", .data = &bcm43438_device_data },
+	{ .compatible = "brcm,bcm4349-bt", .data = &bcm43438_device_data },
 	{ .compatible = "brcm,bcm43540-bt", .data = &bcm4354_device_data },
 	{ .compatible = "brcm,bcm4335a0" },
+	{ .compatible = "infineon,cyw55572-bt" },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, bcm_bluetooth_of_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_bcsp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_bcsp.c
@@ -378,7 +378,7 @@
 		i++;
 
 		__skb_unlink(skb, &bcsp->unack);
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 	}
 
 	if (skb_queue_empty(&bcsp->unack))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_h5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_h5.c
@@ -313,7 +313,7 @@
 			break;
 
 		__skb_unlink(skb, &h5->unack);
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 	}
 
 	if (skb_queue_empty(&h5->unack))
@@ -587,9 +587,11 @@
 		count -= processed;
 	}
 
-	pm_runtime_get(&hu->serdev->dev);
-	pm_runtime_mark_last_busy(&hu->serdev->dev);
-	pm_runtime_put_autosuspend(&hu->serdev->dev);
+	if (hu->serdev) {
+		pm_runtime_get(&hu->serdev->dev);
+		pm_runtime_mark_last_busy(&hu->serdev->dev);
+		pm_runtime_put_autosuspend(&hu->serdev->dev);
+	}
 
 	return 0;
 }
@@ -627,9 +629,11 @@
 		break;
 	}
 
-	pm_runtime_get_sync(&hu->serdev->dev);
-	pm_runtime_mark_last_busy(&hu->serdev->dev);
-	pm_runtime_put_autosuspend(&hu->serdev->dev);
+	if (hu->serdev) {
+		pm_runtime_get_sync(&hu->serdev->dev);
+		pm_runtime_mark_last_busy(&hu->serdev->dev);
+		pm_runtime_put_autosuspend(&hu->serdev->dev);
+	}
 
 	return 0;
 }
@@ -846,6 +850,8 @@
 		h5->vnd = data->vnd;
 	}
 
+	if (data->driver_info & H5_INFO_WAKEUP_DISABLE)
+		set_bit(H5_WAKEUP_DISABLE, &h5->flags);
 
 	h5->enable_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW);
 	if (IS_ERR(h5->enable_gpio))
@@ -860,9 +866,6 @@
 	if (err)
 		return err;
 
-	if (data->driver_info & H5_INFO_WAKEUP_DISABLE)
-		set_bit(H5_WAKEUP_DISABLE, &h5->flags);
-
 	return 0;
 }
 
@@ -962,11 +965,13 @@
 	serdev_device_set_parity(h5->hu->serdev, SERDEV_PARITY_EVEN);
 	serdev_device_set_baudrate(h5->hu->serdev, 115200);
 
-	pm_runtime_set_active(&h5->hu->serdev->dev);
-	pm_runtime_use_autosuspend(&h5->hu->serdev->dev);
-	pm_runtime_set_autosuspend_delay(&h5->hu->serdev->dev,
-					 SUSPEND_TIMEOUT_MS);
-	pm_runtime_enable(&h5->hu->serdev->dev);
+	if (!test_bit(H5_WAKEUP_DISABLE, &h5->flags)) {
+		pm_runtime_set_active(&h5->hu->serdev->dev);
+		pm_runtime_use_autosuspend(&h5->hu->serdev->dev);
+		pm_runtime_set_autosuspend_delay(&h5->hu->serdev->dev,
+						 SUSPEND_TIMEOUT_MS);
+		pm_runtime_enable(&h5->hu->serdev->dev);
+	}
 
 	/* The controller needs up to 500ms to wakeup */
 	gpiod_set_value_cansleep(h5->enable_gpio, 1);
@@ -976,7 +981,8 @@
 
 static void h5_btrtl_close(struct h5 *h5)
 {
-	pm_runtime_disable(&h5->hu->serdev->dev);
+	if (!test_bit(H5_WAKEUP_DISABLE, &h5->flags))
+		pm_runtime_disable(&h5->hu->serdev->dev);
 
 	gpiod_set_value_cansleep(h5->device_wake_gpio, 0);
 	gpiod_set_value_cansleep(h5->enable_gpio, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_intel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_intel.c
@@ -1217,7 +1217,11 @@
 
 int __init intel_init(void)
 {
-	platform_driver_register(&intel_driver);
+	int err;
+
+	err = platform_driver_register(&intel_driver);
+	if (err)
+		return err;
 
 	return hci_uart_register_proto(&intel_proto);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_ldisc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_ldisc.c
@@ -479,6 +479,9 @@
 
 	BT_DBG("tty %p", tty);
 
+	if (!capable(CAP_NET_ADMIN))
+		return -EPERM;
+
 	/* Error if the tty has no write op instead of leaving an exploitable
 	 * hole
 	 */
@@ -490,6 +493,11 @@
 		BT_ERR("Can't allocate control structure");
 		return -ENFILE;
 	}
+	if (percpu_init_rwsem(&hu->proto_lock)) {
+		BT_ERR("Can't allocate semaphore structure");
+		kfree(hu);
+		return -ENOMEM;
+	}
 
 	tty->disc_data = hu;
 	hu->tty = tty;
@@ -502,8 +510,6 @@
 	INIT_WORK(&hu->init_ready, hci_uart_init_work);
 	INIT_WORK(&hu->write_work, hci_uart_write_work);
 
-	percpu_init_rwsem(&hu->proto_lock);
-
 	/* Flush any pending characters in the driver */
 	tty_driver_flush_buffer(tty);
 
@@ -765,7 +771,8 @@
 		break;
 
 	case HCIUARTGETPROTO:
-		if (test_bit(HCI_UART_PROTO_SET, &hu->flags))
+		if (test_bit(HCI_UART_PROTO_SET, &hu->flags) &&
+		    test_bit(HCI_UART_PROTO_READY, &hu->flags))
 			err = hu->proto->id;
 		else
 			err = -EUNATCH;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_ll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_ll.c
@@ -345,7 +345,7 @@
 	default:
 		BT_ERR("illegal hcill state: %ld (losing packet)",
 		       ll->hcill_state);
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 		break;
 	}
 
@@ -626,7 +626,7 @@
 		gpiod_set_value_cansleep(lldev->enable_gpio, 0);
 		msleep(5);
 		gpiod_set_value_cansleep(lldev->enable_gpio, 1);
-		mdelay(100);
+		msleep(500);
 		err = serdev_device_wait_for_cts(serdev, true, 200);
 		if (err) {
 			bt_dev_err(hu->hdev, "Failed to get CTS");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_nokia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_nokia.c
@@ -734,7 +734,11 @@
 		return err;
 	}
 
-	clk_prepare_enable(sysclk);
+	err = clk_prepare_enable(sysclk);
+	if (err) {
+		dev_err(dev, "could not enable sysclk: %d", err);
+		return err;
+	}
 	btdev->sysclk_speed = clk_get_rate(sysclk);
 	clk_disable_unprepare(sysclk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_qca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_qca.c
@@ -78,7 +78,8 @@
 	QCA_HW_ERROR_EVENT,
 	QCA_SSR_TRIGGERED,
 	QCA_BT_OFF,
-	QCA_ROM_FW
+	QCA_ROM_FW,
+	QCA_DEBUGFS_CREATED,
 };
 
 enum qca_capabilities {
@@ -605,9 +606,18 @@
 	if (hu->serdev) {
 		qcadev = serdev_device_get_drvdata(hu->serdev);
 
-		if (qca_is_wcn399x(qcadev->btsoc_type) ||
-		    qca_is_wcn6750(qcadev->btsoc_type))
+		switch (qcadev->btsoc_type) {
+		case QCA_WCN3988:
+		case QCA_WCN3990:
+		case QCA_WCN3991:
+		case QCA_WCN3998:
+		case QCA_WCN6750:
 			hu->init_speed = qcadev->init_speed;
+			break;
+
+		default:
+			break;
+		}
 
 		if (qcadev->oper_speed)
 			hu->oper_speed = qcadev->oper_speed;
@@ -635,6 +645,9 @@
 	if (!hdev->debugfs)
 		return;
 
+	if (test_and_set_bit(QCA_DEBUGFS_CREATED, &qca->flags))
+		return;
+
 	ibs_dir = debugfs_create_dir("ibs", hdev->debugfs);
 
 	/* read only */
@@ -696,9 +709,9 @@
 	skb_queue_purge(&qca->tx_wait_q);
 	skb_queue_purge(&qca->txq);
 	skb_queue_purge(&qca->rx_memdump_q);
-	del_timer(&qca->tx_idle_timer);
-	del_timer(&qca->wake_retrans_timer);
 	destroy_workqueue(qca->workqueue);
+	del_timer_sync(&qca->tx_idle_timer);
+	del_timer_sync(&qca->wake_retrans_timer);
 	qca->hu = NULL;
 
 	kfree_skb(qca->rx_skb);
@@ -912,7 +925,7 @@
 	default:
 		BT_ERR("Illegal tx state: %d (losing packet)",
 		       qca->tx_ibs_state);
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 		break;
 	}
 
@@ -1310,11 +1323,19 @@
 		      msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));
 
 	/* Give the controller time to process the request */
-	if (qca_is_wcn399x(qca_soc_type(hu)) ||
-	    qca_is_wcn6750(qca_soc_type(hu)))
+	switch (qca_soc_type(hu)) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		usleep_range(1000, 10000);
-	else
+		break;
+
+	default:
 		msleep(300);
+	}
 
 	return 0;
 }
@@ -1387,12 +1408,19 @@
 
 static int qca_check_speeds(struct hci_uart *hu)
 {
-	if (qca_is_wcn399x(qca_soc_type(hu)) ||
-	    qca_is_wcn6750(qca_soc_type(hu))) {
+	switch (qca_soc_type(hu)) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
 		    !qca_get_speed(hu, QCA_OPER_SPEED))
 			return -EINVAL;
-	} else {
+		break;
+
+	default:
 		if (!qca_get_speed(hu, QCA_INIT_SPEED) ||
 		    !qca_get_speed(hu, QCA_OPER_SPEED))
 			return -EINVAL;
@@ -1421,13 +1449,28 @@
 		/* Disable flow control for wcn3990 to deassert RTS while
 		 * changing the baudrate of chip and host.
 		 */
-		if (qca_is_wcn399x(soc_type) ||
-		    qca_is_wcn6750(soc_type))
+		switch (soc_type) {
+		case QCA_WCN3988:
+		case QCA_WCN3990:
+		case QCA_WCN3991:
+		case QCA_WCN3998:
+		case QCA_WCN6750:
+		case QCA_WCN6855:
 			hci_uart_set_flow_control(hu, true);
+			break;
 
-		if (soc_type == QCA_WCN3990) {
+		default:
+			break;
+		}
+
+		switch (soc_type) {
+		case QCA_WCN3990:
 			reinit_completion(&qca->drop_ev_comp);
 			set_bit(QCA_DROP_VENDOR_EVENT, &qca->flags);
+			break;
+
+		default:
+			break;
 		}
 
 		qca_baudrate = qca_get_baudrate_value(speed);
@@ -1439,11 +1482,22 @@
 		host_set_baudrate(hu, speed);
 
 error:
-		if (qca_is_wcn399x(soc_type) ||
-		    qca_is_wcn6750(soc_type))
+		switch (soc_type) {
+		case QCA_WCN3988:
+		case QCA_WCN3990:
+		case QCA_WCN3991:
+		case QCA_WCN3998:
+		case QCA_WCN6750:
+		case QCA_WCN6855:
 			hci_uart_set_flow_control(hu, false);
+			break;
 
-		if (soc_type == QCA_WCN3990) {
+		default:
+			break;
+		}
+
+		switch (soc_type) {
+		case QCA_WCN3990:
 			/* Wait for the controller to send the vendor event
 			 * for the baudrate change command.
 			 */
@@ -1455,6 +1509,10 @@
 			}
 
 			clear_bit(QCA_DROP_VENDOR_EVENT, &qca->flags);
+			break;
+
+		default:
+			break;
 		}
 	}
 
@@ -1582,10 +1640,14 @@
 	struct hci_uart *hu = hci_get_drvdata(hdev);
 	bool wakeup;
 
-	/* UART driver handles the interrupt from BT SoC.So we need to use
-	 * device handle of UART driver to get the status of device may wakeup.
+	if (!hu->serdev)
+		return true;
+
+	/* BT SoC attached through the serial bus is handled by the serdev driver.
+	 * So we need to use the device handle of the serdev driver to get the
+	 * status of device may wakeup.
 	 */
-	wakeup = device_may_wakeup(hu->serdev->ctrl->dev.parent);
+	wakeup = device_may_wakeup(&hu->serdev->ctrl->dev);
 	bt_dev_dbg(hu->hdev, "wakeup status : %d", wakeup);
 
 	return !wakeup;
@@ -1615,12 +1677,20 @@
 		}
 	}
 
-	if (qca_is_wcn399x(soc_type)) {
+	switch (soc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
 		/* Forcefully enable wcn399x to enter in to boot mode. */
 		host_set_baudrate(hu, 2400);
 		ret = qca_send_power_pulse(hu, false);
 		if (ret)
 			return ret;
+		break;
+
+	default:
+		break;
 	}
 
 	/* For wcn6750 need to enable gpio bt_en */
@@ -1637,10 +1707,18 @@
 
 	qca_set_speed(hu, QCA_INIT_SPEED);
 
-	if (qca_is_wcn399x(soc_type)) {
+	switch (soc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
 		ret = qca_send_power_pulse(hu, true);
 		if (ret)
 			return ret;
+		break;
+
+	default:
+		break;
 	}
 
 	/* Now the device is in ready state to communicate with host.
@@ -1674,10 +1752,17 @@
 	if (!hu->serdev)
 		return 0;
 
-	if (qca_is_wcn399x(soc_type) ||
-	    qca_is_wcn6750(soc_type)) {
+	switch (soc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		ret = qca_regulator_init(hu);
-	} else {
+		break;
+
+	default:
 		qcadev = serdev_device_get_drvdata(hu->serdev);
 		if (qcadev->bt_en) {
 			gpiod_set_value_cansleep(qcadev->bt_en, 1);
@@ -1700,6 +1785,7 @@
 	const char *firmware_name = qca_get_firmware_name(hu);
 	int ret;
 	struct qca_btsoc_version ver;
+	const char *soc_name;
 
 	ret = qca_check_speeds(hu);
 	if (ret)
@@ -1714,9 +1800,30 @@
 	 */
 	set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
 
-	bt_dev_info(hdev, "setting up %s",
-		qca_is_wcn399x(soc_type) ? "wcn399x" :
-		(soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
+	switch (soc_type) {
+	case QCA_QCA2066:
+		soc_name = "qca2066";
+		break;
+
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+		soc_name = "wcn399x";
+		break;
+
+	case QCA_WCN6750:
+		soc_name = "wcn6750";
+		break;
+
+	case QCA_WCN6855:
+		soc_name = "wcn6855";
+		break;
+
+	default:
+		soc_name = "ROME/QCA6390";
+	}
+	bt_dev_info(hdev, "setting up %s", soc_name);
 
 	qca->memdump_state = QCA_MEMDUMP_IDLE;
 
@@ -1727,14 +1834,21 @@
 
 	clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
 
-	if (qca_is_wcn399x(soc_type) ||
-	    qca_is_wcn6750(soc_type)) {
+	switch (soc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
 
 		ret = qca_read_soc_version(hdev, &ver, soc_type);
 		if (ret)
 			goto out;
-	} else {
+		break;
+
+	default:
 		qca_set_speed(hu, QCA_INIT_SPEED);
 	}
 
@@ -1748,8 +1862,16 @@
 		qca_baudrate = qca_get_baudrate_value(speed);
 	}
 
-	if (!(qca_is_wcn399x(soc_type) ||
-	     qca_is_wcn6750(soc_type))) {
+	switch (soc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
+		break;
+
+	default:
 		/* Get QCA version information */
 		ret = qca_read_soc_version(hdev, &ver, soc_type);
 		if (ret)
@@ -1818,7 +1940,18 @@
 	.dequeue	= qca_dequeue,
 };
 
-static const struct qca_device_data qca_soc_data_wcn3990 = {
+static const struct qca_device_data qca_soc_data_wcn3988 __maybe_unused = {
+	.soc_type = QCA_WCN3988,
+	.vregs = (struct qca_vreg []) {
+		{ "vddio", 15000  },
+		{ "vddxo", 80000  },
+		{ "vddrf", 300000 },
+		{ "vddch0", 450000 },
+	},
+	.num_vregs = 4,
+};
+
+static const struct qca_device_data qca_soc_data_wcn3990 __maybe_unused = {
 	.soc_type = QCA_WCN3990,
 	.vregs = (struct qca_vreg []) {
 		{ "vddio", 15000  },
@@ -1829,7 +1962,7 @@
 	.num_vregs = 4,
 };
 
-static const struct qca_device_data qca_soc_data_wcn3991 = {
+static const struct qca_device_data qca_soc_data_wcn3991 __maybe_unused = {
 	.soc_type = QCA_WCN3991,
 	.vregs = (struct qca_vreg []) {
 		{ "vddio", 15000  },
@@ -1841,7 +1974,7 @@
 	.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
 };
 
-static const struct qca_device_data qca_soc_data_wcn3998 = {
+static const struct qca_device_data qca_soc_data_wcn3998 __maybe_unused = {
 	.soc_type = QCA_WCN3998,
 	.vregs = (struct qca_vreg []) {
 		{ "vddio", 10000  },
@@ -1852,12 +1985,18 @@
 	.num_vregs = 4,
 };
 
-static const struct qca_device_data qca_soc_data_qca6390 = {
+static const struct qca_device_data qca_soc_data_qca2066 __maybe_unused = {
+	.soc_type = QCA_QCA2066,
+	.num_vregs = 0,
+};
+
+static const struct qca_device_data qca_soc_data_qca6390 __maybe_unused = {
 	.soc_type = QCA_QCA6390,
 	.num_vregs = 0,
+	.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
 };
 
-static const struct qca_device_data qca_soc_data_wcn6750 = {
+static const struct qca_device_data qca_soc_data_wcn6750 __maybe_unused = {
 	.soc_type = QCA_WCN6750,
 	.vregs = (struct qca_vreg []) {
 		{ "vddio", 5000 },
@@ -1874,6 +2013,20 @@
 	.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
 };
 
+static const struct qca_device_data qca_soc_data_wcn6855 = {
+	.soc_type = QCA_WCN6855,
+	.vregs = (struct qca_vreg []) {
+		{ "vddio", 5000 },
+		{ "vddbtcxmx", 126000 },
+		{ "vddrfacmn", 12500 },
+		{ "vddrfa0p8", 102000 },
+		{ "vddrfa1p7", 302000 },
+		{ "vddrfa1p2", 257000 },
+	},
+	.num_vregs = 6,
+	.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
+};
+
 static void qca_power_shutdown(struct hci_uart *hu)
 {
 	struct qca_serdev *qcadev;
@@ -1899,11 +2052,18 @@
 
 	qcadev = serdev_device_get_drvdata(hu->serdev);
 
-	if (qca_is_wcn399x(soc_type)) {
+	switch (soc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
 		host_set_baudrate(hu, 2400);
 		qca_send_power_pulse(hu, false);
 		qca_regulator_disable(qcadev);
-	} else if (soc_type == QCA_WCN6750) {
+		break;
+
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		gpiod_set_value_cansleep(qcadev->bt_en, 0);
 		msleep(100);
 		qca_regulator_disable(qcadev);
@@ -1911,7 +2071,9 @@
 			sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
 			bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
 		}
-	} else if (qcadev->bt_en) {
+		break;
+
+	default:
 		gpiod_set_value_cansleep(qcadev->bt_en, 0);
 	}
 
@@ -1927,6 +2089,9 @@
 	hu->hdev->hw_error = NULL;
 	hu->hdev->cmd_timeout = NULL;
 
+	del_timer_sync(&qca->wake_retrans_timer);
+	del_timer_sync(&qca->tx_idle_timer);
+
 	/* Stop sending shutdown command if soc crashes. */
 	if (soc_type != QCA_ROME
 		&& qca->memdump_state == QCA_MEMDUMP_IDLE) {
@@ -2033,10 +2198,18 @@
 	if (!qcadev->oper_speed)
 		BT_DBG("UART will pick default operating speed");
 
-	if (data &&
-	    (qca_is_wcn399x(data->soc_type) ||
-	    qca_is_wcn6750(data->soc_type))) {
+	if (data)
 		qcadev->btsoc_type = data->soc_type;
+	else
+		qcadev->btsoc_type = QCA_ROME;
+
+	switch (qcadev->btsoc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
 		qcadev->bt_power = devm_kzalloc(&serdev->dev,
 						sizeof(struct qca_power),
 						GFP_KERNEL);
@@ -2055,14 +2228,18 @@
 
 		qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
 					       GPIOD_OUT_LOW);
-		if (!qcadev->bt_en && data->soc_type == QCA_WCN6750) {
+		if (IS_ERR(qcadev->bt_en) &&
+		    (data->soc_type == QCA_WCN6750 ||
+		     data->soc_type == QCA_WCN6855)) {
 			dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
 			power_ctrl_enabled = false;
 		}
 
 		qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
 					       GPIOD_IN);
-		if (!qcadev->sw_ctrl && data->soc_type == QCA_WCN6750)
+		if (IS_ERR(qcadev->sw_ctrl) &&
+		    (data->soc_type == QCA_WCN6750 ||
+		     data->soc_type == QCA_WCN6855))
 			dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
 
 		qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
@@ -2076,15 +2253,12 @@
 			BT_ERR("wcn3990 serdev registration failed");
 			return err;
 		}
-	} else {
-		if (data)
-			qcadev->btsoc_type = data->soc_type;
-		else
-			qcadev->btsoc_type = QCA_ROME;
+		break;
 
+	default:
 		qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
 					       GPIOD_OUT_LOW);
-		if (!qcadev->bt_en) {
+		if (IS_ERR(qcadev->bt_en)) {
 			dev_warn(&serdev->dev, "failed to acquire enable gpio\n");
 			power_ctrl_enabled = false;
 		}
@@ -2137,12 +2311,23 @@
 	struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
 	struct qca_power *power = qcadev->bt_power;
 
-	if ((qca_is_wcn399x(qcadev->btsoc_type) ||
-	     qca_is_wcn6750(qcadev->btsoc_type)) &&
-	     power->vregs_on)
-		qca_power_shutdown(&qcadev->serdev_hu);
-	else if (qcadev->susclk)
-		clk_disable_unprepare(qcadev->susclk);
+	switch (qcadev->btsoc_type) {
+	case QCA_WCN3988:
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+	case QCA_WCN6750:
+	case QCA_WCN6855:
+		if (power->vregs_on) {
+			qca_power_shutdown(&qcadev->serdev_hu);
+			break;
+		}
+		fallthrough;
+
+	default:
+		if (qcadev->susclk)
+			clk_disable_unprepare(qcadev->susclk);
+	}
 
 	hci_uart_unregister_device(&qcadev->serdev_hu);
 }
@@ -2153,10 +2338,29 @@
 	int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS);
 	struct serdev_device *serdev = to_serdev_device(dev);
 	struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
+	struct hci_uart *hu = &qcadev->serdev_hu;
+	struct hci_dev *hdev = hu->hdev;
 	const u8 ibs_wake_cmd[] = { 0xFD };
 	const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 };
 
 	if (qcadev->btsoc_type == QCA_QCA6390) {
+		/* The purpose of sending the VSC is to reset SOC into a initial
+		 * state and the state will ensure next hdev->setup() success.
+		 * if HCI_QUIRK_NON_PERSISTENT_SETUP is set, it means that
+		 * hdev->setup() can do its job regardless of SoC state, so
+		 * don't need to send the VSC.
+		 * if HCI_SETUP is set, it means that hdev->setup() was never
+		 * invoked and the SOC is already in the initial state, so
+		 * don't also need to send the VSC.
+		 */
+		if (test_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks) ||
+		    hci_dev_test_flag(hdev, HCI_SETUP))
+			return;
+
+		/* The serdev must be in open state when conrol logic arrives
+		 * here, so also fix the use-after-free issue caused by that
+		 * the serdev is flushed or wrote after it is closed.
+		 */
 		serdev_device_write_flush(serdev);
 		ret = serdev_device_write_buf(serdev, ibs_wake_cmd,
 					      sizeof(ibs_wake_cmd));
@@ -2309,13 +2513,16 @@
 
 #ifdef CONFIG_OF
 static const struct of_device_id qca_bluetooth_of_match[] = {
+	{ .compatible = "qcom,qca2066-bt", .data = &qca_soc_data_qca2066},
 	{ .compatible = "qcom,qca6174-bt" },
 	{ .compatible = "qcom,qca6390-bt", .data = &qca_soc_data_qca6390},
 	{ .compatible = "qcom,qca9377-bt" },
+	{ .compatible = "qcom,wcn3988-bt", .data = &qca_soc_data_wcn3988},
 	{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990},
 	{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
 	{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
 	{ .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
+	{ .compatible = "qcom,wcn6855-bt", .data = &qca_soc_data_wcn6855},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
@@ -2323,6 +2530,7 @@
 
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id qca_bluetooth_acpi_match[] = {
+	{ "QCOM2066", (kernel_ulong_t)&qca_soc_data_qca2066 },
 	{ "QCOM6390", (kernel_ulong_t)&qca_soc_data_qca6390 },
 	{ "DLA16390", (kernel_ulong_t)&qca_soc_data_qca6390 },
 	{ "DLB16390", (kernel_ulong_t)&qca_soc_data_qca6390 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_serdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_serdev.c
@@ -301,9 +301,12 @@
 
 	serdev_device_set_client_ops(hu->serdev, &hci_serdev_client_ops);
 
+	if (percpu_init_rwsem(&hu->proto_lock))
+		return -ENOMEM;
+
 	err = serdev_device_open(hu->serdev);
 	if (err)
-		return err;
+		goto err_rwsem;
 
 	err = p->open(hu);
 	if (err)
@@ -327,7 +330,6 @@
 
 	INIT_WORK(&hu->init_ready, hci_uart_init_work);
 	INIT_WORK(&hu->write_work, hci_uart_write_work);
-	percpu_init_rwsem(&hu->proto_lock);
 
 	/* Only when vendor specific setup callback is provided, consider
 	 * the manufacturer information valid. This avoids filling in the
@@ -377,6 +379,8 @@
 	p->close(hu);
 err_open:
 	serdev_device_close(hu->serdev);
+err_rwsem:
+	percpu_free_rwsem(&hu->proto_lock);
 	return err;
 }
 EXPORT_SYMBOL_GPL(hci_uart_register_device);
@@ -398,5 +402,6 @@
 		clear_bit(HCI_UART_PROTO_READY, &hu->flags);
 		serdev_device_close(hu->serdev);
 	}
+	percpu_free_rwsem(&hu->proto_lock);
 }
 EXPORT_SYMBOL_GPL(hci_uart_unregister_device);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/hci_vhci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/hci_vhci.c
@@ -67,7 +67,10 @@
 	struct vhci_data *data = hci_get_drvdata(hdev);
 
 	memcpy(skb_push(skb, 1), &hci_skb_pkt_type(skb), 1);
+
+	mutex_lock(&data->open_mutex);
 	skb_queue_tail(&data->readq, skb);
+	mutex_unlock(&data->open_mutex);
 
 	wake_up_interruptible(&data->read_wait);
 	return 0;
@@ -121,6 +124,8 @@
 	if (opcode & 0x80)
 		set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
 
+	set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
+
 	if (hci_register_dev(hdev) < 0) {
 		BT_ERR("Can't register HCI device");
 		hci_free_dev(hdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bluetooth/virtio_bt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bluetooth/virtio_bt.c
@@ -202,6 +202,9 @@
 		hci_skb_pkt_type(skb) = pkt_type;
 		hci_recv_frame(vbt->hdev, skb);
 		break;
+	default:
+		kfree_skb(skb);
+		break;
 	}
 }
 
@@ -216,7 +219,7 @@
 	if (!skb)
 		return;
 
-	skb->len = len;
+	skb_put(skb, len);
 	virtbt_rx_handle(vbt, skb);
 
 	if (virtbt_add_inbuf(vbt) < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/Kconfig
@@ -175,11 +175,12 @@
 
 config TEGRA_ACONNECT
 	tristate "Tegra ACONNECT Bus Driver"
-	depends on ARCH_TEGRA_210_SOC
+	depends on ARCH_TEGRA
 	depends on OF && PM
 	help
 	  Driver for the Tegra ACONNECT bus which is used to interface with
-	  the devices inside the Audio Processing Engine (APE) for Tegra210.
+	  the devices inside the Audio Processing Engine (APE) for
+	  Tegra210 and later.
 
 config TEGRA_GMI
 	tristate "Tegra Generic Memory Interface bus driver"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/Makefile
@@ -39,4 +39,4 @@
 obj-$(CONFIG_DA8XX_MSTPRI)	+= da8xx-mstpri.o
 
 # MHI
-obj-$(CONFIG_MHI_BUS)		+= mhi/
+obj-y				+= mhi/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/arm-integrator-lm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/arm-integrator-lm.c
@@ -85,6 +85,7 @@
 		return -ENODEV;
 	}
 	map = syscon_node_to_regmap(syscon);
+	of_node_put(syscon);
 	if (IS_ERR(map)) {
 		dev_err(dev,
 			"could not find Integrator/AP system controller\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -1236,14 +1236,14 @@
 static int fsl_mc_bus_remove(struct platform_device *pdev)
 {
 	struct fsl_mc *mc = platform_get_drvdata(pdev);
+	struct fsl_mc_io *mc_io;
 
 	if (!fsl_mc_is_root_dprc(&mc->root_mc_bus_dev->dev))
 		return -EINVAL;
 
+	mc_io = mc->root_mc_bus_dev->mc_io;
 	fsl_mc_device_remove(mc->root_mc_bus_dev);
-
-	fsl_destroy_mc_io(mc->root_mc_bus_dev->mc_io);
-	mc->root_mc_bus_dev->mc_io = NULL;
+	fsl_destroy_mc_io(mc_io);
 
 	bus_unregister_notifier(&fsl_mc_bus_type, &fsl_mc_nb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/hisi_lpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/hisi_lpc.c
@@ -503,13 +503,13 @@
 {
 	struct acpi_device *adev = ACPI_COMPANION(hostdev);
 	struct acpi_device *child;
+	struct platform_device *pdev;
 	int ret;
 
 	/* Only consider the children of the host */
 	list_for_each_entry(child, &adev->children, node) {
 		const char *hid = acpi_device_hid(child);
 		const struct hisi_lpc_acpi_cell *cell;
-		struct platform_device *pdev;
 		const struct resource *res;
 		bool found = false;
 		int num_res;
@@ -571,22 +571,24 @@
 
 		ret = platform_device_add_resources(pdev, res, num_res);
 		if (ret)
-			goto fail;
+			goto fail_put_device;
 
 		ret = platform_device_add_data(pdev, cell->pdata,
 					       cell->pdata_size);
 		if (ret)
-			goto fail;
+			goto fail_put_device;
 
 		ret = platform_device_add(pdev);
 		if (ret)
-			goto fail;
+			goto fail_put_device;
 
 		acpi_device_set_enumerated(child);
 	}
 
 	return 0;
 
+fail_put_device:
+	platform_device_put(pdev);
 fail:
 	hisi_lpc_acpi_remove(hostdev);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/imx-weim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/imx-weim.c
@@ -192,8 +192,8 @@
 	const struct of_device_id *of_id = of_match_device(weim_id_table,
 							   &pdev->dev);
 	const struct imx_weim_devtype *devtype = of_id->data;
+	int ret = 0, have_child = 0;
 	struct device_node *child;
-	int ret, have_child = 0;
 	struct cs_timing_state ts = {};
 	u32 reg;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/intel-ixp4xx-eb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/intel-ixp4xx-eb.c
@@ -33,7 +33,7 @@
 #define IXP4XX_EXP_TIMING_STRIDE	0x04
 #define IXP4XX_EXP_CS_EN		BIT(31)
 #define IXP456_EXP_PAR_EN		BIT(30) /* Only on IXP45x and IXP46x */
-#define IXP4XX_EXP_T1_MASK		GENMASK(28, 27)
+#define IXP4XX_EXP_T1_MASK		GENMASK(29, 28)
 #define IXP4XX_EXP_T1_SHIFT		28
 #define IXP4XX_EXP_T2_MASK		GENMASK(27, 26)
 #define IXP4XX_EXP_T2_SHIFT		26
@@ -49,7 +49,7 @@
 #define IXP4XX_EXP_SIZE_SHIFT		10
 #define IXP4XX_EXP_CNFG_0		BIT(9) /* Always zero */
 #define IXP43X_EXP_SYNC_INTEL		BIT(8) /* Only on IXP43x */
-#define IXP43X_EXP_EXP_CHIP		BIT(7) /* Only on IXP43x */
+#define IXP43X_EXP_EXP_CHIP		BIT(7) /* Only on IXP43x, dangerous to touch on IXP42x */
 #define IXP4XX_EXP_BYTE_RD16		BIT(6)
 #define IXP4XX_EXP_HRDY_POL		BIT(5) /* Only on IXP42x */
 #define IXP4XX_EXP_MUX_EN		BIT(4)
@@ -57,8 +57,6 @@
 #define IXP4XX_EXP_WORD			BIT(2) /* Always zero */
 #define IXP4XX_EXP_WR_EN		BIT(1)
 #define IXP4XX_EXP_BYTE_EN		BIT(0)
-#define IXP42X_RESERVED			(BIT(30)|IXP4XX_EXP_CNFG_0|BIT(8)|BIT(7)|IXP4XX_EXP_WORD)
-#define IXP43X_RESERVED			(BIT(30)|IXP4XX_EXP_CNFG_0|BIT(5)|IXP4XX_EXP_WORD)
 
 #define IXP4XX_EXP_CNFG0		0x20
 #define IXP4XX_EXP_CNFG0_MEM_MAP	BIT(31)
@@ -252,10 +250,9 @@
 		cs_cfg |= val << IXP4XX_EXP_CYC_TYPE_SHIFT;
 	}
 
-	if (eb->is_42x)
-		cs_cfg &= ~IXP42X_RESERVED;
 	if (eb->is_43x) {
-		cs_cfg &= ~IXP43X_RESERVED;
+		/* Should always be zero */
+		cs_cfg &= ~IXP4XX_EXP_WORD;
 		/*
 		 * This bit for Intel strata flash is currently unused, but let's
 		 * report it if we find one.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/Kconfig
@@ -2,30 +2,7 @@
 #
 # MHI bus
 #
-# Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+# Copyright (c) 2021, Linaro Ltd.
 #
 
-config MHI_BUS
-	tristate "Modem Host Interface (MHI) bus"
-	help
-	  Bus driver for MHI protocol. Modem Host Interface (MHI) is a
-	  communication protocol used by the host processors to control
-	  and communicate with modem devices over a high speed peripheral
-	  bus or shared memory.
-
-config MHI_BUS_DEBUG
-	bool "Debugfs support for the MHI bus"
-	depends on MHI_BUS && DEBUG_FS
-	help
-	  Enable debugfs support for use with the MHI transport. Allows
-	  reading and/or modifying some values within the MHI controller
-	  for debug and test purposes.
-
-config MHI_BUS_PCI_GENERIC
-	tristate "MHI PCI controller driver"
-	depends on MHI_BUS
-	depends on PCI
-	help
-	  This driver provides MHI PCI controller driver for devices such as
-	  Qualcomm SDX55 based PCIe modems.
-
+source "drivers/bus/mhi/host/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/Makefile
@@ -1,6 +1,2 @@
-# core layer
-obj-y += core/
-
-obj-$(CONFIG_MHI_BUS_PCI_GENERIC) += mhi_pci_generic.o
-mhi_pci_generic-y += pci_generic.o
-
+# Host MHI stack
+obj-y += host/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/Kconfig
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# MHI bus
+#
+# Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+#
+
+config MHI_BUS
+	tristate "Modem Host Interface (MHI) bus"
+	help
+	  Bus driver for MHI protocol. Modem Host Interface (MHI) is a
+	  communication protocol used by the host processors to control
+	  and communicate with modem devices over a high speed peripheral
+	  bus or shared memory.
+
+config MHI_BUS_DEBUG
+	bool "Debugfs support for the MHI bus"
+	depends on MHI_BUS && DEBUG_FS
+	help
+	  Enable debugfs support for use with the MHI transport. Allows
+	  reading and/or modifying some values within the MHI controller
+	  for debug and test purposes.
+
+config MHI_BUS_PCI_GENERIC
+	tristate "MHI PCI controller driver"
+	depends on MHI_BUS
+	depends on PCI
+	help
+	  This driver provides MHI PCI controller driver for devices such as
+	  Qualcomm SDX55 based PCIe modems.
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/Makefile
@@ -0,0 +1,6 @@
+obj-$(CONFIG_MHI_BUS) += mhi.o
+mhi-y := init.o main.o pm.o boot.o
+mhi-$(CONFIG_MHI_BUS_DEBUG) += debugfs.o
+
+obj-$(CONFIG_MHI_BUS_PCI_GENERIC) += mhi_pci_generic.o
+mhi_pci_generic-y += pci_generic.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/boot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/boot.c
@@ -0,0 +1,541 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-direction.h>
+#include <linux/dma-mapping.h>
+#include <linux/firmware.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/mhi.h>
+#include <linux/module.h>
+#include <linux/random.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+#include "internal.h"
+
+/* Setup RDDM vector table for RDDM transfer and program RXVEC */
+void mhi_rddm_prepare(struct mhi_controller *mhi_cntrl,
+		      struct image_info *img_info)
+{
+	struct mhi_buf *mhi_buf = img_info->mhi_buf;
+	struct bhi_vec_entry *bhi_vec = img_info->bhi_vec;
+	void __iomem *base = mhi_cntrl->bhie;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	u32 sequence_id;
+	unsigned int i;
+
+	for (i = 0; i < img_info->entries - 1; i++, mhi_buf++, bhi_vec++) {
+		bhi_vec->dma_addr = mhi_buf->dma_addr;
+		bhi_vec->size = mhi_buf->len;
+	}
+
+	dev_dbg(dev, "BHIe programming for RDDM\n");
+
+	mhi_write_reg(mhi_cntrl, base, BHIE_RXVECADDR_HIGH_OFFS,
+		      upper_32_bits(mhi_buf->dma_addr));
+
+	mhi_write_reg(mhi_cntrl, base, BHIE_RXVECADDR_LOW_OFFS,
+		      lower_32_bits(mhi_buf->dma_addr));
+
+	mhi_write_reg(mhi_cntrl, base, BHIE_RXVECSIZE_OFFS, mhi_buf->len);
+	sequence_id = MHI_RANDOM_U32_NONZERO(BHIE_RXVECSTATUS_SEQNUM_BMSK);
+
+	mhi_write_reg_field(mhi_cntrl, base, BHIE_RXVECDB_OFFS,
+			    BHIE_RXVECDB_SEQNUM_BMSK, BHIE_RXVECDB_SEQNUM_SHFT,
+			    sequence_id);
+
+	dev_dbg(dev, "Address: %p and len: 0x%zx sequence: %u\n",
+		&mhi_buf->dma_addr, mhi_buf->len, sequence_id);
+}
+
+/* Collect RDDM buffer during kernel panic */
+static int __mhi_download_rddm_in_panic(struct mhi_controller *mhi_cntrl)
+{
+	int ret;
+	u32 rx_status;
+	enum mhi_ee_type ee;
+	const u32 delayus = 2000;
+	u32 retry = (mhi_cntrl->timeout_ms * 1000) / delayus;
+	const u32 rddm_timeout_us = 200000;
+	int rddm_retry = rddm_timeout_us / delayus;
+	void __iomem *base = mhi_cntrl->bhie;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+
+	dev_dbg(dev, "Entered with pm_state:%s dev_state:%s ee:%s\n",
+		to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		TO_MHI_STATE_STR(mhi_cntrl->dev_state),
+		TO_MHI_EXEC_STR(mhi_cntrl->ee));
+
+	/*
+	 * This should only be executing during a kernel panic, we expect all
+	 * other cores to shutdown while we're collecting RDDM buffer. After
+	 * returning from this function, we expect the device to reset.
+	 *
+	 * Normaly, we read/write pm_state only after grabbing the
+	 * pm_lock, since we're in a panic, skipping it. Also there is no
+	 * gurantee that this state change would take effect since
+	 * we're setting it w/o grabbing pm_lock
+	 */
+	mhi_cntrl->pm_state = MHI_PM_LD_ERR_FATAL_DETECT;
+	/* update should take the effect immediately */
+	smp_wmb();
+
+	/*
+	 * Make sure device is not already in RDDM. In case the device asserts
+	 * and a kernel panic follows, device will already be in RDDM.
+	 * Do not trigger SYS ERR again and proceed with waiting for
+	 * image download completion.
+	 */
+	ee = mhi_get_exec_env(mhi_cntrl);
+	if (ee == MHI_EE_MAX)
+		goto error_exit_rddm;
+
+	if (ee != MHI_EE_RDDM) {
+		dev_dbg(dev, "Trigger device into RDDM mode using SYS ERR\n");
+		mhi_set_mhi_state(mhi_cntrl, MHI_STATE_SYS_ERR);
+
+		dev_dbg(dev, "Waiting for device to enter RDDM\n");
+		while (rddm_retry--) {
+			ee = mhi_get_exec_env(mhi_cntrl);
+			if (ee == MHI_EE_RDDM)
+				break;
+
+			udelay(delayus);
+		}
+
+		if (rddm_retry <= 0) {
+			/* Hardware reset so force device to enter RDDM */
+			dev_dbg(dev,
+				"Did not enter RDDM, do a host req reset\n");
+			mhi_write_reg(mhi_cntrl, mhi_cntrl->regs,
+				      MHI_SOC_RESET_REQ_OFFSET,
+				      MHI_SOC_RESET_REQ);
+			udelay(delayus);
+		}
+
+		ee = mhi_get_exec_env(mhi_cntrl);
+	}
+
+	dev_dbg(dev,
+		"Waiting for RDDM image download via BHIe, current EE:%s\n",
+		TO_MHI_EXEC_STR(ee));
+
+	while (retry--) {
+		ret = mhi_read_reg_field(mhi_cntrl, base, BHIE_RXVECSTATUS_OFFS,
+					 BHIE_RXVECSTATUS_STATUS_BMSK,
+					 BHIE_RXVECSTATUS_STATUS_SHFT,
+					 &rx_status);
+		if (ret)
+			return -EIO;
+
+		if (rx_status == BHIE_RXVECSTATUS_STATUS_XFER_COMPL)
+			return 0;
+
+		udelay(delayus);
+	}
+
+	ee = mhi_get_exec_env(mhi_cntrl);
+	ret = mhi_read_reg(mhi_cntrl, base, BHIE_RXVECSTATUS_OFFS, &rx_status);
+
+	dev_err(dev, "RXVEC_STATUS: 0x%x\n", rx_status);
+
+error_exit_rddm:
+	dev_err(dev, "RDDM transfer failed. Current EE: %s\n",
+		TO_MHI_EXEC_STR(ee));
+
+	return -EIO;
+}
+
+/* Download RDDM image from device */
+int mhi_download_rddm_image(struct mhi_controller *mhi_cntrl, bool in_panic)
+{
+	void __iomem *base = mhi_cntrl->bhie;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	u32 rx_status;
+
+	if (in_panic)
+		return __mhi_download_rddm_in_panic(mhi_cntrl);
+
+	dev_dbg(dev, "Waiting for RDDM image download via BHIe\n");
+
+	/* Wait for the image download to complete */
+	wait_event_timeout(mhi_cntrl->state_event,
+			   mhi_read_reg_field(mhi_cntrl, base,
+					      BHIE_RXVECSTATUS_OFFS,
+					      BHIE_RXVECSTATUS_STATUS_BMSK,
+					      BHIE_RXVECSTATUS_STATUS_SHFT,
+					      &rx_status) || rx_status,
+			   msecs_to_jiffies(mhi_cntrl->timeout_ms));
+
+	return (rx_status == BHIE_RXVECSTATUS_STATUS_XFER_COMPL) ? 0 : -EIO;
+}
+EXPORT_SYMBOL_GPL(mhi_download_rddm_image);
+
+static int mhi_fw_load_bhie(struct mhi_controller *mhi_cntrl,
+			    const struct mhi_buf *mhi_buf)
+{
+	void __iomem *base = mhi_cntrl->bhie;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	rwlock_t *pm_lock = &mhi_cntrl->pm_lock;
+	u32 tx_status, sequence_id;
+	int ret;
+
+	read_lock_bh(pm_lock);
+	if (!MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state)) {
+		read_unlock_bh(pm_lock);
+		return -EIO;
+	}
+
+	sequence_id = MHI_RANDOM_U32_NONZERO(BHIE_TXVECSTATUS_SEQNUM_BMSK);
+	dev_dbg(dev, "Starting image download via BHIe. Sequence ID: %u\n",
+		sequence_id);
+	mhi_write_reg(mhi_cntrl, base, BHIE_TXVECADDR_HIGH_OFFS,
+		      upper_32_bits(mhi_buf->dma_addr));
+
+	mhi_write_reg(mhi_cntrl, base, BHIE_TXVECADDR_LOW_OFFS,
+		      lower_32_bits(mhi_buf->dma_addr));
+
+	mhi_write_reg(mhi_cntrl, base, BHIE_TXVECSIZE_OFFS, mhi_buf->len);
+
+	mhi_write_reg_field(mhi_cntrl, base, BHIE_TXVECDB_OFFS,
+			    BHIE_TXVECDB_SEQNUM_BMSK, BHIE_TXVECDB_SEQNUM_SHFT,
+			    sequence_id);
+	read_unlock_bh(pm_lock);
+
+	/* Wait for the image download to complete */
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+				 MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state) ||
+				 mhi_read_reg_field(mhi_cntrl, base,
+						   BHIE_TXVECSTATUS_OFFS,
+						   BHIE_TXVECSTATUS_STATUS_BMSK,
+						   BHIE_TXVECSTATUS_STATUS_SHFT,
+						   &tx_status) || tx_status,
+				 msecs_to_jiffies(mhi_cntrl->timeout_ms));
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state) ||
+	    tx_status != BHIE_TXVECSTATUS_STATUS_XFER_COMPL)
+		return -EIO;
+
+	return (!ret) ? -ETIMEDOUT : 0;
+}
+
+static int mhi_fw_load_bhi(struct mhi_controller *mhi_cntrl,
+			   dma_addr_t dma_addr,
+			   size_t size)
+{
+	u32 tx_status, val, session_id;
+	int i, ret;
+	void __iomem *base = mhi_cntrl->bhi;
+	rwlock_t *pm_lock = &mhi_cntrl->pm_lock;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	struct {
+		char *name;
+		u32 offset;
+	} error_reg[] = {
+		{ "ERROR_CODE", BHI_ERRCODE },
+		{ "ERROR_DBG1", BHI_ERRDBG1 },
+		{ "ERROR_DBG2", BHI_ERRDBG2 },
+		{ "ERROR_DBG3", BHI_ERRDBG3 },
+		{ NULL },
+	};
+
+	read_lock_bh(pm_lock);
+	if (!MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state)) {
+		read_unlock_bh(pm_lock);
+		goto invalid_pm_state;
+	}
+
+	session_id = MHI_RANDOM_U32_NONZERO(BHI_TXDB_SEQNUM_BMSK);
+	dev_dbg(dev, "Starting image download via BHI. Session ID: %u\n",
+		session_id);
+	mhi_write_reg(mhi_cntrl, base, BHI_STATUS, 0);
+	mhi_write_reg(mhi_cntrl, base, BHI_IMGADDR_HIGH,
+		      upper_32_bits(dma_addr));
+	mhi_write_reg(mhi_cntrl, base, BHI_IMGADDR_LOW,
+		      lower_32_bits(dma_addr));
+	mhi_write_reg(mhi_cntrl, base, BHI_IMGSIZE, size);
+	mhi_write_reg(mhi_cntrl, base, BHI_IMGTXDB, session_id);
+	read_unlock_bh(pm_lock);
+
+	/* Wait for the image download to complete */
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+			   MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state) ||
+			   mhi_read_reg_field(mhi_cntrl, base, BHI_STATUS,
+					      BHI_STATUS_MASK, BHI_STATUS_SHIFT,
+					      &tx_status) || tx_status,
+			   msecs_to_jiffies(mhi_cntrl->timeout_ms));
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state))
+		goto invalid_pm_state;
+
+	if (tx_status == BHI_STATUS_ERROR) {
+		dev_err(dev, "Image transfer failed\n");
+		read_lock_bh(pm_lock);
+		if (MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state)) {
+			for (i = 0; error_reg[i].name; i++) {
+				ret = mhi_read_reg(mhi_cntrl, base,
+						   error_reg[i].offset, &val);
+				if (ret)
+					break;
+				dev_err(dev, "Reg: %s value: 0x%x\n",
+					error_reg[i].name, val);
+			}
+		}
+		read_unlock_bh(pm_lock);
+		goto invalid_pm_state;
+	}
+
+	return (!ret) ? -ETIMEDOUT : 0;
+
+invalid_pm_state:
+
+	return -EIO;
+}
+
+void mhi_free_bhie_table(struct mhi_controller *mhi_cntrl,
+			 struct image_info *image_info)
+{
+	int i;
+	struct mhi_buf *mhi_buf = image_info->mhi_buf;
+
+	for (i = 0; i < image_info->entries; i++, mhi_buf++)
+		dma_free_coherent(mhi_cntrl->cntrl_dev, mhi_buf->len,
+				  mhi_buf->buf, mhi_buf->dma_addr);
+
+	kfree(image_info->mhi_buf);
+	kfree(image_info);
+}
+
+int mhi_alloc_bhie_table(struct mhi_controller *mhi_cntrl,
+			 struct image_info **image_info,
+			 size_t alloc_size)
+{
+	size_t seg_size = mhi_cntrl->seg_len;
+	int segments = DIV_ROUND_UP(alloc_size, seg_size) + 1;
+	int i;
+	struct image_info *img_info;
+	struct mhi_buf *mhi_buf;
+
+	img_info = kzalloc(sizeof(*img_info), GFP_KERNEL);
+	if (!img_info)
+		return -ENOMEM;
+
+	/* Allocate memory for entries */
+	img_info->mhi_buf = kcalloc(segments, sizeof(*img_info->mhi_buf),
+				    GFP_KERNEL);
+	if (!img_info->mhi_buf)
+		goto error_alloc_mhi_buf;
+
+	/* Allocate and populate vector table */
+	mhi_buf = img_info->mhi_buf;
+	for (i = 0; i < segments; i++, mhi_buf++) {
+		size_t vec_size = seg_size;
+
+		/* Vector table is the last entry */
+		if (i == segments - 1)
+			vec_size = sizeof(struct bhi_vec_entry) * i;
+
+		mhi_buf->len = vec_size;
+		mhi_buf->buf = dma_alloc_coherent(mhi_cntrl->cntrl_dev,
+						  vec_size, &mhi_buf->dma_addr,
+						  GFP_KERNEL);
+		if (!mhi_buf->buf)
+			goto error_alloc_segment;
+	}
+
+	img_info->bhi_vec = img_info->mhi_buf[segments - 1].buf;
+	img_info->entries = segments;
+	*image_info = img_info;
+
+	return 0;
+
+error_alloc_segment:
+	for (--i, --mhi_buf; i >= 0; i--, mhi_buf--)
+		dma_free_coherent(mhi_cntrl->cntrl_dev, mhi_buf->len,
+				  mhi_buf->buf, mhi_buf->dma_addr);
+
+error_alloc_mhi_buf:
+	kfree(img_info);
+
+	return -ENOMEM;
+}
+
+static void mhi_firmware_copy(struct mhi_controller *mhi_cntrl,
+			      const struct firmware *firmware,
+			      struct image_info *img_info)
+{
+	size_t remainder = firmware->size;
+	size_t to_cpy;
+	const u8 *buf = firmware->data;
+	struct mhi_buf *mhi_buf = img_info->mhi_buf;
+	struct bhi_vec_entry *bhi_vec = img_info->bhi_vec;
+
+	while (remainder) {
+		to_cpy = min(remainder, mhi_buf->len);
+		memcpy(mhi_buf->buf, buf, to_cpy);
+		bhi_vec->dma_addr = mhi_buf->dma_addr;
+		bhi_vec->size = to_cpy;
+
+		buf += to_cpy;
+		remainder -= to_cpy;
+		bhi_vec++;
+		mhi_buf++;
+	}
+}
+
+void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
+{
+	const struct firmware *firmware = NULL;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_pm_state new_state;
+	const char *fw_name;
+	void *buf;
+	dma_addr_t dma_addr;
+	size_t size;
+	int i, ret;
+
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		dev_err(dev, "Device MHI is not in valid state\n");
+		return;
+	}
+
+	/* save hardware info from BHI */
+	ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_SERIALNU,
+			   &mhi_cntrl->serial_number);
+	if (ret)
+		dev_err(dev, "Could not capture serial number via BHI\n");
+
+	for (i = 0; i < ARRAY_SIZE(mhi_cntrl->oem_pk_hash); i++) {
+		ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_OEMPKHASH(i),
+				   &mhi_cntrl->oem_pk_hash[i]);
+		if (ret) {
+			dev_err(dev, "Could not capture OEM PK HASH via BHI\n");
+			break;
+		}
+	}
+
+	/* wait for ready on pass through or any other execution environment */
+	if (mhi_cntrl->ee != MHI_EE_EDL && mhi_cntrl->ee != MHI_EE_PBL)
+		goto fw_load_ready_state;
+
+	fw_name = (mhi_cntrl->ee == MHI_EE_EDL) ?
+		mhi_cntrl->edl_image : mhi_cntrl->fw_image;
+
+	if (!fw_name || (mhi_cntrl->fbc_download && (!mhi_cntrl->sbl_size ||
+						     !mhi_cntrl->seg_len))) {
+		dev_err(dev,
+			"No firmware image defined or !sbl_size || !seg_len\n");
+		goto error_fw_load;
+	}
+
+	ret = request_firmware(&firmware, fw_name, dev);
+	if (ret) {
+		dev_err(dev, "Error loading firmware: %d\n", ret);
+		goto error_fw_load;
+	}
+
+	size = (mhi_cntrl->fbc_download) ? mhi_cntrl->sbl_size : firmware->size;
+
+	/* SBL size provided is maximum size, not necessarily the image size */
+	if (size > firmware->size)
+		size = firmware->size;
+
+	buf = dma_alloc_coherent(mhi_cntrl->cntrl_dev, size, &dma_addr,
+				 GFP_KERNEL);
+	if (!buf) {
+		release_firmware(firmware);
+		goto error_fw_load;
+	}
+
+	/* Download image using BHI */
+	memcpy(buf, firmware->data, size);
+	ret = mhi_fw_load_bhi(mhi_cntrl, dma_addr, size);
+	dma_free_coherent(mhi_cntrl->cntrl_dev, size, buf, dma_addr);
+
+	/* Error or in EDL mode, we're done */
+	if (ret) {
+		dev_err(dev, "MHI did not load image over BHI, ret: %d\n", ret);
+		release_firmware(firmware);
+		goto error_fw_load;
+	}
+
+	/* Wait for ready since EDL image was loaded */
+	if (fw_name == mhi_cntrl->edl_image) {
+		release_firmware(firmware);
+		goto fw_load_ready_state;
+	}
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	mhi_cntrl->dev_state = MHI_STATE_RESET;
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	/*
+	 * If we're doing fbc, populate vector tables while
+	 * device transitioning into MHI READY state
+	 */
+	if (mhi_cntrl->fbc_download) {
+		ret = mhi_alloc_bhie_table(mhi_cntrl, &mhi_cntrl->fbc_image,
+					   firmware->size);
+		if (ret) {
+			release_firmware(firmware);
+			goto error_fw_load;
+		}
+
+		/* Load the firmware into BHIE vec table */
+		mhi_firmware_copy(mhi_cntrl, firmware, mhi_cntrl->fbc_image);
+	}
+
+	release_firmware(firmware);
+
+fw_load_ready_state:
+	/* Transitioning into MHI RESET->READY state */
+	ret = mhi_ready_state_transition(mhi_cntrl);
+	if (ret) {
+		dev_err(dev, "MHI did not enter READY state\n");
+		goto error_ready_state;
+	}
+
+	dev_info(dev, "Wait for device to enter SBL or Mission mode\n");
+	return;
+
+error_ready_state:
+	if (mhi_cntrl->fbc_download) {
+		mhi_free_bhie_table(mhi_cntrl, mhi_cntrl->fbc_image);
+		mhi_cntrl->fbc_image = NULL;
+	}
+
+error_fw_load:
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	new_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_FW_DL_ERR);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+	if (new_state == MHI_PM_FW_DL_ERR)
+		wake_up_all(&mhi_cntrl->state_event);
+}
+
+int mhi_download_amss_image(struct mhi_controller *mhi_cntrl)
+{
+	struct image_info *image_info = mhi_cntrl->fbc_image;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_pm_state new_state;
+	int ret;
+
+	if (!image_info)
+		return -EIO;
+
+	ret = mhi_fw_load_bhie(mhi_cntrl,
+			       /* Vector table is the last entry */
+			       &image_info->mhi_buf[image_info->entries - 1]);
+	if (ret) {
+		dev_err(dev, "MHI did not load AMSS, ret:%d\n", ret);
+		write_lock_irq(&mhi_cntrl->pm_lock);
+		new_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_FW_DL_ERR);
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		if (new_state == MHI_PM_FW_DL_ERR)
+			wake_up_all(&mhi_cntrl->state_event);
+	}
+
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/debugfs.c
@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/mhi.h>
+#include <linux/module.h>
+#include "internal.h"
+
+static int mhi_debugfs_states_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+
+	/* states */
+	seq_printf(m, "PM state: %s Device: %s MHI state: %s EE: %s wake: %s\n",
+		   to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		   mhi_is_active(mhi_cntrl) ? "Active" : "Inactive",
+		   TO_MHI_STATE_STR(mhi_cntrl->dev_state),
+		   TO_MHI_EXEC_STR(mhi_cntrl->ee),
+		   mhi_cntrl->wake_set ? "true" : "false");
+
+	/* counters */
+	seq_printf(m, "M0: %u M2: %u M3: %u", mhi_cntrl->M0, mhi_cntrl->M2,
+		   mhi_cntrl->M3);
+
+	seq_printf(m, " device wake: %u pending packets: %u\n",
+		   atomic_read(&mhi_cntrl->dev_wake),
+		   atomic_read(&mhi_cntrl->pending_pkts));
+
+	return 0;
+}
+
+static int mhi_debugfs_events_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+	struct mhi_event *mhi_event;
+	struct mhi_event_ctxt *er_ctxt;
+	int i;
+
+	if (!mhi_is_active(mhi_cntrl)) {
+		seq_puts(m, "Device not ready\n");
+		return -ENODEV;
+	}
+
+	er_ctxt = mhi_cntrl->mhi_ctxt->er_ctxt;
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings;
+						i++, er_ctxt++, mhi_event++) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		if (mhi_event->offload_ev) {
+			seq_printf(m, "Index: %d is an offload event ring\n",
+				   i);
+			continue;
+		}
+
+		seq_printf(m, "Index: %d intmod count: %lu time: %lu",
+			   i, (le32_to_cpu(er_ctxt->intmod) & EV_CTX_INTMODC_MASK) >>
+			   EV_CTX_INTMODC_SHIFT,
+			   (le32_to_cpu(er_ctxt->intmod) & EV_CTX_INTMODT_MASK) >>
+			   EV_CTX_INTMODT_SHIFT);
+
+		seq_printf(m, " base: 0x%0llx len: 0x%llx", le64_to_cpu(er_ctxt->rbase),
+			   le64_to_cpu(er_ctxt->rlen));
+
+		seq_printf(m, " rp: 0x%llx wp: 0x%llx", le64_to_cpu(er_ctxt->rp),
+			   le64_to_cpu(er_ctxt->wp));
+
+		seq_printf(m, " local rp: 0x%pK db: 0x%pad\n", ring->rp,
+			   &mhi_event->db_cfg.db_val);
+	}
+
+	return 0;
+}
+
+static int mhi_debugfs_channels_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+	struct mhi_chan *mhi_chan;
+	struct mhi_chan_ctxt *chan_ctxt;
+	int i;
+
+	if (!mhi_is_active(mhi_cntrl)) {
+		seq_puts(m, "Device not ready\n");
+		return -ENODEV;
+	}
+
+	mhi_chan = mhi_cntrl->mhi_chan;
+	chan_ctxt = mhi_cntrl->mhi_ctxt->chan_ctxt;
+	for (i = 0; i < mhi_cntrl->max_chan; i++, chan_ctxt++, mhi_chan++) {
+		struct mhi_ring *ring = &mhi_chan->tre_ring;
+
+		if (mhi_chan->offload_ch) {
+			seq_printf(m, "%s(%u) is an offload channel\n",
+				   mhi_chan->name, mhi_chan->chan);
+			continue;
+		}
+
+		if (!mhi_chan->mhi_dev)
+			continue;
+
+		seq_printf(m,
+			   "%s(%u) state: 0x%lx brstmode: 0x%lx pollcfg: 0x%lx",
+			   mhi_chan->name, mhi_chan->chan, (le32_to_cpu(chan_ctxt->chcfg) &
+			   CHAN_CTX_CHSTATE_MASK) >> CHAN_CTX_CHSTATE_SHIFT,
+			   (le32_to_cpu(chan_ctxt->chcfg) & CHAN_CTX_BRSTMODE_MASK) >>
+			   CHAN_CTX_BRSTMODE_SHIFT, (le32_to_cpu(chan_ctxt->chcfg) &
+			   CHAN_CTX_POLLCFG_MASK) >> CHAN_CTX_POLLCFG_SHIFT);
+
+		seq_printf(m, " type: 0x%x event ring: %u", le32_to_cpu(chan_ctxt->chtype),
+			   le32_to_cpu(chan_ctxt->erindex));
+
+		seq_printf(m, " base: 0x%llx len: 0x%llx rp: 0x%llx wp: 0x%llx",
+			   le64_to_cpu(chan_ctxt->rbase), le64_to_cpu(chan_ctxt->rlen),
+			   le64_to_cpu(chan_ctxt->rp), le64_to_cpu(chan_ctxt->wp));
+
+		seq_printf(m, " local rp: 0x%pK local wp: 0x%pK db: 0x%pad\n",
+			   ring->rp, ring->wp,
+			   &mhi_chan->db_cfg.db_val);
+	}
+
+	return 0;
+}
+
+static int mhi_device_info_show(struct device *dev, void *data)
+{
+	struct mhi_device *mhi_dev;
+
+	if (dev->bus != &mhi_bus_type)
+		return 0;
+
+	mhi_dev = to_mhi_device(dev);
+
+	seq_printf((struct seq_file *)data, "%s: type: %s dev_wake: %u",
+		   mhi_dev->name, mhi_dev->dev_type ? "Controller" : "Transfer",
+		   mhi_dev->dev_wake);
+
+	/* for transfer device types only */
+	if (mhi_dev->dev_type == MHI_DEVICE_XFER)
+		seq_printf((struct seq_file *)data, " channels: %u(UL)/%u(DL)",
+			   mhi_dev->ul_chan_id, mhi_dev->dl_chan_id);
+
+	seq_puts((struct seq_file *)data, "\n");
+
+	return 0;
+}
+
+static int mhi_debugfs_devices_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+
+	if (!mhi_is_active(mhi_cntrl)) {
+		seq_puts(m, "Device not ready\n");
+		return -ENODEV;
+	}
+
+	/* Show controller and client(s) info */
+	mhi_device_info_show(&mhi_cntrl->mhi_dev->dev, m);
+	device_for_each_child(&mhi_cntrl->mhi_dev->dev, m, mhi_device_info_show);
+
+	return 0;
+}
+
+static int mhi_debugfs_regdump_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+	enum mhi_state state;
+	enum mhi_ee_type ee;
+	int i, ret = -EIO;
+	u32 val;
+	void __iomem *mhi_base = mhi_cntrl->regs;
+	void __iomem *bhi_base = mhi_cntrl->bhi;
+	void __iomem *bhie_base = mhi_cntrl->bhie;
+	void __iomem *wake_db = mhi_cntrl->wake_db;
+	struct {
+		const char *name;
+		int offset;
+		void __iomem *base;
+	} regs[] = {
+		{ "MHI_REGLEN", MHIREGLEN, mhi_base},
+		{ "MHI_VER", MHIVER, mhi_base},
+		{ "MHI_CFG", MHICFG, mhi_base},
+		{ "MHI_CTRL", MHICTRL, mhi_base},
+		{ "MHI_STATUS", MHISTATUS, mhi_base},
+		{ "MHI_WAKE_DB", 0, wake_db},
+		{ "BHI_EXECENV", BHI_EXECENV, bhi_base},
+		{ "BHI_STATUS", BHI_STATUS, bhi_base},
+		{ "BHI_ERRCODE", BHI_ERRCODE, bhi_base},
+		{ "BHI_ERRDBG1", BHI_ERRDBG1, bhi_base},
+		{ "BHI_ERRDBG2", BHI_ERRDBG2, bhi_base},
+		{ "BHI_ERRDBG3", BHI_ERRDBG3, bhi_base},
+		{ "BHIE_TXVEC_DB", BHIE_TXVECDB_OFFS, bhie_base},
+		{ "BHIE_TXVEC_STATUS", BHIE_TXVECSTATUS_OFFS, bhie_base},
+		{ "BHIE_RXVEC_DB", BHIE_RXVECDB_OFFS, bhie_base},
+		{ "BHIE_RXVEC_STATUS", BHIE_RXVECSTATUS_OFFS, bhie_base},
+		{ NULL },
+	};
+
+	if (!MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state))
+		return ret;
+
+	seq_printf(m, "Host PM state: %s Device state: %s EE: %s\n",
+		   to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		   TO_MHI_STATE_STR(mhi_cntrl->dev_state),
+		   TO_MHI_EXEC_STR(mhi_cntrl->ee));
+
+	state = mhi_get_mhi_state(mhi_cntrl);
+	ee = mhi_get_exec_env(mhi_cntrl);
+	seq_printf(m, "Device EE: %s state: %s\n", TO_MHI_EXEC_STR(ee),
+		   TO_MHI_STATE_STR(state));
+
+	for (i = 0; regs[i].name; i++) {
+		if (!regs[i].base)
+			continue;
+		ret = mhi_read_reg(mhi_cntrl, regs[i].base, regs[i].offset,
+				   &val);
+		if (ret)
+			continue;
+
+		seq_printf(m, "%s: 0x%x\n", regs[i].name, val);
+	}
+
+	return 0;
+}
+
+static int mhi_debugfs_device_wake_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+	struct mhi_device *mhi_dev = mhi_cntrl->mhi_dev;
+
+	if (!mhi_is_active(mhi_cntrl)) {
+		seq_puts(m, "Device not ready\n");
+		return -ENODEV;
+	}
+
+	seq_printf(m,
+		   "Wake count: %d\n%s\n", mhi_dev->dev_wake,
+		   "Usage: echo get/put > device_wake to vote/unvote for M0");
+
+	return 0;
+}
+
+static ssize_t mhi_debugfs_device_wake_write(struct file *file,
+					     const char __user *ubuf,
+					     size_t count, loff_t *ppos)
+{
+	struct seq_file	*m = file->private_data;
+	struct mhi_controller *mhi_cntrl = m->private;
+	struct mhi_device *mhi_dev = mhi_cntrl->mhi_dev;
+	char buf[16];
+	int ret = -EINVAL;
+
+	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
+		return -EFAULT;
+
+	if (!strncmp(buf, "get", 3)) {
+		ret = mhi_device_get_sync(mhi_dev);
+	} else if (!strncmp(buf, "put", 3)) {
+		mhi_device_put(mhi_dev);
+		ret = 0;
+	}
+
+	return ret ? ret : count;
+}
+
+static int mhi_debugfs_timeout_ms_show(struct seq_file *m, void *d)
+{
+	struct mhi_controller *mhi_cntrl = m->private;
+
+	seq_printf(m, "%u ms\n", mhi_cntrl->timeout_ms);
+
+	return 0;
+}
+
+static ssize_t mhi_debugfs_timeout_ms_write(struct file *file,
+					    const char __user *ubuf,
+					    size_t count, loff_t *ppos)
+{
+	struct seq_file	*m = file->private_data;
+	struct mhi_controller *mhi_cntrl = m->private;
+	u32 timeout_ms;
+
+	if (kstrtou32_from_user(ubuf, count, 0, &timeout_ms))
+		return -EINVAL;
+
+	mhi_cntrl->timeout_ms = timeout_ms;
+
+	return count;
+}
+
+static int mhi_debugfs_states_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_states_show, inode->i_private);
+}
+
+static int mhi_debugfs_events_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_events_show, inode->i_private);
+}
+
+static int mhi_debugfs_channels_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_channels_show, inode->i_private);
+}
+
+static int mhi_debugfs_devices_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_devices_show, inode->i_private);
+}
+
+static int mhi_debugfs_regdump_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_regdump_show, inode->i_private);
+}
+
+static int mhi_debugfs_device_wake_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_device_wake_show, inode->i_private);
+}
+
+static int mhi_debugfs_timeout_ms_open(struct inode *inode, struct file *fp)
+{
+	return single_open(fp, mhi_debugfs_timeout_ms_show, inode->i_private);
+}
+
+static const struct file_operations debugfs_states_fops = {
+	.open = mhi_debugfs_states_open,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static const struct file_operations debugfs_events_fops = {
+	.open = mhi_debugfs_events_open,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static const struct file_operations debugfs_channels_fops = {
+	.open = mhi_debugfs_channels_open,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static const struct file_operations debugfs_devices_fops = {
+	.open = mhi_debugfs_devices_open,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static const struct file_operations debugfs_regdump_fops = {
+	.open = mhi_debugfs_regdump_open,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static const struct file_operations debugfs_device_wake_fops = {
+	.open = mhi_debugfs_device_wake_open,
+	.write = mhi_debugfs_device_wake_write,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static const struct file_operations debugfs_timeout_ms_fops = {
+	.open = mhi_debugfs_timeout_ms_open,
+	.write = mhi_debugfs_timeout_ms_write,
+	.release = single_release,
+	.read = seq_read,
+};
+
+static struct dentry *mhi_debugfs_root;
+
+void mhi_create_debugfs(struct mhi_controller *mhi_cntrl)
+{
+	mhi_cntrl->debugfs_dentry =
+			debugfs_create_dir(dev_name(&mhi_cntrl->mhi_dev->dev),
+					   mhi_debugfs_root);
+
+	debugfs_create_file("states", 0444, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_states_fops);
+	debugfs_create_file("events", 0444, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_events_fops);
+	debugfs_create_file("channels", 0444, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_channels_fops);
+	debugfs_create_file("devices", 0444, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_devices_fops);
+	debugfs_create_file("regdump", 0444, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_regdump_fops);
+	debugfs_create_file("device_wake", 0644, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_device_wake_fops);
+	debugfs_create_file("timeout_ms", 0644, mhi_cntrl->debugfs_dentry,
+			    mhi_cntrl, &debugfs_timeout_ms_fops);
+}
+
+void mhi_destroy_debugfs(struct mhi_controller *mhi_cntrl)
+{
+	debugfs_remove_recursive(mhi_cntrl->debugfs_dentry);
+	mhi_cntrl->debugfs_dentry = NULL;
+}
+
+void mhi_debugfs_init(void)
+{
+	mhi_debugfs_root = debugfs_create_dir(mhi_bus_type.name, NULL);
+}
+
+void mhi_debugfs_exit(void)
+{
+	debugfs_remove_recursive(mhi_debugfs_root);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/init.c
@@ -0,0 +1,1443 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/dma-direction.h>
+#include <linux/dma-mapping.h>
+#include <linux/idr.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/mhi.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/wait.h>
+#include "internal.h"
+
+static DEFINE_IDA(mhi_controller_ida);
+
+const char * const mhi_ee_str[MHI_EE_MAX] = {
+	[MHI_EE_PBL] = "PRIMARY BOOTLOADER",
+	[MHI_EE_SBL] = "SECONDARY BOOTLOADER",
+	[MHI_EE_AMSS] = "MISSION MODE",
+	[MHI_EE_RDDM] = "RAMDUMP DOWNLOAD MODE",
+	[MHI_EE_WFW] = "WLAN FIRMWARE",
+	[MHI_EE_PTHRU] = "PASS THROUGH",
+	[MHI_EE_EDL] = "EMERGENCY DOWNLOAD",
+	[MHI_EE_FP] = "FLASH PROGRAMMER",
+	[MHI_EE_DISABLE_TRANSITION] = "DISABLE",
+	[MHI_EE_NOT_SUPPORTED] = "NOT SUPPORTED",
+};
+
+const char * const dev_state_tran_str[DEV_ST_TRANSITION_MAX] = {
+	[DEV_ST_TRANSITION_PBL] = "PBL",
+	[DEV_ST_TRANSITION_READY] = "READY",
+	[DEV_ST_TRANSITION_SBL] = "SBL",
+	[DEV_ST_TRANSITION_MISSION_MODE] = "MISSION MODE",
+	[DEV_ST_TRANSITION_FP] = "FLASH PROGRAMMER",
+	[DEV_ST_TRANSITION_SYS_ERR] = "SYS ERROR",
+	[DEV_ST_TRANSITION_DISABLE] = "DISABLE",
+};
+
+const char * const mhi_state_str[MHI_STATE_MAX] = {
+	[MHI_STATE_RESET] = "RESET",
+	[MHI_STATE_READY] = "READY",
+	[MHI_STATE_M0] = "M0",
+	[MHI_STATE_M1] = "M1",
+	[MHI_STATE_M2] = "M2",
+	[MHI_STATE_M3] = "M3",
+	[MHI_STATE_M3_FAST] = "M3 FAST",
+	[MHI_STATE_BHI] = "BHI",
+	[MHI_STATE_SYS_ERR] = "SYS ERROR",
+};
+
+const char * const mhi_ch_state_type_str[MHI_CH_STATE_TYPE_MAX] = {
+	[MHI_CH_STATE_TYPE_RESET] = "RESET",
+	[MHI_CH_STATE_TYPE_STOP] = "STOP",
+	[MHI_CH_STATE_TYPE_START] = "START",
+};
+
+static const char * const mhi_pm_state_str[] = {
+	[MHI_PM_STATE_DISABLE] = "DISABLE",
+	[MHI_PM_STATE_POR] = "POWER ON RESET",
+	[MHI_PM_STATE_M0] = "M0",
+	[MHI_PM_STATE_M2] = "M2",
+	[MHI_PM_STATE_M3_ENTER] = "M?->M3",
+	[MHI_PM_STATE_M3] = "M3",
+	[MHI_PM_STATE_M3_EXIT] = "M3->M0",
+	[MHI_PM_STATE_FW_DL_ERR] = "Firmware Download Error",
+	[MHI_PM_STATE_SYS_ERR_DETECT] = "SYS ERROR Detect",
+	[MHI_PM_STATE_SYS_ERR_PROCESS] = "SYS ERROR Process",
+	[MHI_PM_STATE_SHUTDOWN_PROCESS] = "SHUTDOWN Process",
+	[MHI_PM_STATE_LD_ERR_FATAL_DETECT] = "Linkdown or Error Fatal Detect",
+};
+
+const char *to_mhi_pm_state_str(u32 state)
+{
+	int index;
+
+	if (state)
+		index = __fls(state);
+
+	if (!state || index >= ARRAY_SIZE(mhi_pm_state_str))
+		return "Invalid State";
+
+	return mhi_pm_state_str[index];
+}
+
+static ssize_t serial_number_show(struct device *dev,
+				  struct device_attribute *attr,
+				  char *buf)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+
+	return snprintf(buf, PAGE_SIZE, "Serial Number: %u\n",
+			mhi_cntrl->serial_number);
+}
+static DEVICE_ATTR_RO(serial_number);
+
+static ssize_t oem_pk_hash_show(struct device *dev,
+				struct device_attribute *attr,
+				char *buf)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	int i, cnt = 0;
+
+	for (i = 0; i < ARRAY_SIZE(mhi_cntrl->oem_pk_hash); i++)
+		cnt += snprintf(buf + cnt, PAGE_SIZE - cnt,
+				"OEMPKHASH[%d]: 0x%x\n", i,
+				mhi_cntrl->oem_pk_hash[i]);
+
+	return cnt;
+}
+static DEVICE_ATTR_RO(oem_pk_hash);
+
+static struct attribute *mhi_dev_attrs[] = {
+	&dev_attr_serial_number.attr,
+	&dev_attr_oem_pk_hash.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(mhi_dev);
+
+/* MHI protocol requires the transfer ring to be aligned with ring length */
+static int mhi_alloc_aligned_ring(struct mhi_controller *mhi_cntrl,
+				  struct mhi_ring *ring,
+				  u64 len)
+{
+	ring->alloc_size = len + (len - 1);
+	ring->pre_aligned = dma_alloc_coherent(mhi_cntrl->cntrl_dev, ring->alloc_size,
+					       &ring->dma_handle, GFP_KERNEL);
+	if (!ring->pre_aligned)
+		return -ENOMEM;
+
+	ring->iommu_base = (ring->dma_handle + (len - 1)) & ~(len - 1);
+	ring->base = ring->pre_aligned + (ring->iommu_base - ring->dma_handle);
+
+	return 0;
+}
+
+void mhi_deinit_free_irq(struct mhi_controller *mhi_cntrl)
+{
+	int i;
+	struct mhi_event *mhi_event = mhi_cntrl->mhi_event;
+
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		if (mhi_event->offload_ev)
+			continue;
+
+		free_irq(mhi_cntrl->irq[mhi_event->irq], mhi_event);
+	}
+
+	free_irq(mhi_cntrl->irq[0], mhi_cntrl);
+}
+
+int mhi_init_irq_setup(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_event *mhi_event = mhi_cntrl->mhi_event;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	unsigned long irq_flags = IRQF_SHARED | IRQF_NO_SUSPEND;
+	int i, ret;
+
+	/* if controller driver has set irq_flags, use it */
+	if (mhi_cntrl->irq_flags)
+		irq_flags = mhi_cntrl->irq_flags;
+
+	/* Setup BHI_INTVEC IRQ */
+	ret = request_threaded_irq(mhi_cntrl->irq[0], mhi_intvec_handler,
+				   mhi_intvec_threaded_handler,
+				   irq_flags,
+				   "bhi", mhi_cntrl);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		if (mhi_event->offload_ev)
+			continue;
+
+		if (mhi_event->irq >= mhi_cntrl->nr_irqs) {
+			dev_err(dev, "irq %d not available for event ring\n",
+				mhi_event->irq);
+			ret = -EINVAL;
+			goto error_request;
+		}
+
+		ret = request_irq(mhi_cntrl->irq[mhi_event->irq],
+				  mhi_irq_handler,
+				  irq_flags,
+				  "mhi", mhi_event);
+		if (ret) {
+			dev_err(dev, "Error requesting irq:%d for ev:%d\n",
+				mhi_cntrl->irq[mhi_event->irq], i);
+			goto error_request;
+		}
+	}
+
+	return 0;
+
+error_request:
+	for (--i, --mhi_event; i >= 0; i--, mhi_event--) {
+		if (mhi_event->offload_ev)
+			continue;
+
+		free_irq(mhi_cntrl->irq[mhi_event->irq], mhi_event);
+	}
+	free_irq(mhi_cntrl->irq[0], mhi_cntrl);
+
+	return ret;
+}
+
+void mhi_deinit_dev_ctxt(struct mhi_controller *mhi_cntrl)
+{
+	int i;
+	struct mhi_ctxt *mhi_ctxt = mhi_cntrl->mhi_ctxt;
+	struct mhi_cmd *mhi_cmd;
+	struct mhi_event *mhi_event;
+	struct mhi_ring *ring;
+
+	mhi_cmd = mhi_cntrl->mhi_cmd;
+	for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++) {
+		ring = &mhi_cmd->ring;
+		dma_free_coherent(mhi_cntrl->cntrl_dev, ring->alloc_size,
+				  ring->pre_aligned, ring->dma_handle);
+		ring->base = NULL;
+		ring->iommu_base = 0;
+	}
+
+	dma_free_coherent(mhi_cntrl->cntrl_dev,
+			  sizeof(*mhi_ctxt->cmd_ctxt) * NR_OF_CMD_RINGS,
+			  mhi_ctxt->cmd_ctxt, mhi_ctxt->cmd_ctxt_addr);
+
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		if (mhi_event->offload_ev)
+			continue;
+
+		ring = &mhi_event->ring;
+		dma_free_coherent(mhi_cntrl->cntrl_dev, ring->alloc_size,
+				  ring->pre_aligned, ring->dma_handle);
+		ring->base = NULL;
+		ring->iommu_base = 0;
+	}
+
+	dma_free_coherent(mhi_cntrl->cntrl_dev, sizeof(*mhi_ctxt->er_ctxt) *
+			  mhi_cntrl->total_ev_rings, mhi_ctxt->er_ctxt,
+			  mhi_ctxt->er_ctxt_addr);
+
+	dma_free_coherent(mhi_cntrl->cntrl_dev, sizeof(*mhi_ctxt->chan_ctxt) *
+			  mhi_cntrl->max_chan, mhi_ctxt->chan_ctxt,
+			  mhi_ctxt->chan_ctxt_addr);
+
+	kfree(mhi_ctxt);
+	mhi_cntrl->mhi_ctxt = NULL;
+}
+
+int mhi_init_dev_ctxt(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_ctxt *mhi_ctxt;
+	struct mhi_chan_ctxt *chan_ctxt;
+	struct mhi_event_ctxt *er_ctxt;
+	struct mhi_cmd_ctxt *cmd_ctxt;
+	struct mhi_chan *mhi_chan;
+	struct mhi_event *mhi_event;
+	struct mhi_cmd *mhi_cmd;
+	u32 tmp;
+	int ret = -ENOMEM, i;
+
+	atomic_set(&mhi_cntrl->dev_wake, 0);
+	atomic_set(&mhi_cntrl->pending_pkts, 0);
+
+	mhi_ctxt = kzalloc(sizeof(*mhi_ctxt), GFP_KERNEL);
+	if (!mhi_ctxt)
+		return -ENOMEM;
+
+	/* Setup channel ctxt */
+	mhi_ctxt->chan_ctxt = dma_alloc_coherent(mhi_cntrl->cntrl_dev,
+						 sizeof(*mhi_ctxt->chan_ctxt) *
+						 mhi_cntrl->max_chan,
+						 &mhi_ctxt->chan_ctxt_addr,
+						 GFP_KERNEL);
+	if (!mhi_ctxt->chan_ctxt)
+		goto error_alloc_chan_ctxt;
+
+	mhi_chan = mhi_cntrl->mhi_chan;
+	chan_ctxt = mhi_ctxt->chan_ctxt;
+	for (i = 0; i < mhi_cntrl->max_chan; i++, chan_ctxt++, mhi_chan++) {
+		/* Skip if it is an offload channel */
+		if (mhi_chan->offload_ch)
+			continue;
+
+		tmp = le32_to_cpu(chan_ctxt->chcfg);
+		tmp &= ~CHAN_CTX_CHSTATE_MASK;
+		tmp |= (MHI_CH_STATE_DISABLED << CHAN_CTX_CHSTATE_SHIFT);
+		tmp &= ~CHAN_CTX_BRSTMODE_MASK;
+		tmp |= (mhi_chan->db_cfg.brstmode << CHAN_CTX_BRSTMODE_SHIFT);
+		tmp &= ~CHAN_CTX_POLLCFG_MASK;
+		tmp |= (mhi_chan->db_cfg.pollcfg << CHAN_CTX_POLLCFG_SHIFT);
+		chan_ctxt->chcfg = cpu_to_le32(tmp);
+
+		chan_ctxt->chtype = cpu_to_le32(mhi_chan->type);
+		chan_ctxt->erindex = cpu_to_le32(mhi_chan->er_index);
+
+		mhi_chan->ch_state = MHI_CH_STATE_DISABLED;
+		mhi_chan->tre_ring.db_addr = (void __iomem *)&chan_ctxt->wp;
+	}
+
+	/* Setup event context */
+	mhi_ctxt->er_ctxt = dma_alloc_coherent(mhi_cntrl->cntrl_dev,
+					       sizeof(*mhi_ctxt->er_ctxt) *
+					       mhi_cntrl->total_ev_rings,
+					       &mhi_ctxt->er_ctxt_addr,
+					       GFP_KERNEL);
+	if (!mhi_ctxt->er_ctxt)
+		goto error_alloc_er_ctxt;
+
+	er_ctxt = mhi_ctxt->er_ctxt;
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, er_ctxt++,
+		     mhi_event++) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		/* Skip if it is an offload event */
+		if (mhi_event->offload_ev)
+			continue;
+
+		tmp = le32_to_cpu(er_ctxt->intmod);
+		tmp &= ~EV_CTX_INTMODC_MASK;
+		tmp &= ~EV_CTX_INTMODT_MASK;
+		tmp |= (mhi_event->intmod << EV_CTX_INTMODT_SHIFT);
+		er_ctxt->intmod = cpu_to_le32(tmp);
+
+		er_ctxt->ertype = cpu_to_le32(MHI_ER_TYPE_VALID);
+		er_ctxt->msivec = cpu_to_le32(mhi_event->irq);
+		mhi_event->db_cfg.db_mode = true;
+
+		ring->el_size = sizeof(struct mhi_ring_element);
+		ring->len = ring->el_size * ring->elements;
+		ret = mhi_alloc_aligned_ring(mhi_cntrl, ring, ring->len);
+		if (ret)
+			goto error_alloc_er;
+
+		/*
+		 * If the read pointer equals to the write pointer, then the
+		 * ring is empty
+		 */
+		ring->rp = ring->wp = ring->base;
+		er_ctxt->rbase = cpu_to_le64(ring->iommu_base);
+		er_ctxt->rp = er_ctxt->wp = er_ctxt->rbase;
+		er_ctxt->rlen = cpu_to_le64(ring->len);
+		ring->ctxt_wp = &er_ctxt->wp;
+	}
+
+	/* Setup cmd context */
+	ret = -ENOMEM;
+	mhi_ctxt->cmd_ctxt = dma_alloc_coherent(mhi_cntrl->cntrl_dev,
+						sizeof(*mhi_ctxt->cmd_ctxt) *
+						NR_OF_CMD_RINGS,
+						&mhi_ctxt->cmd_ctxt_addr,
+						GFP_KERNEL);
+	if (!mhi_ctxt->cmd_ctxt)
+		goto error_alloc_er;
+
+	mhi_cmd = mhi_cntrl->mhi_cmd;
+	cmd_ctxt = mhi_ctxt->cmd_ctxt;
+	for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++, cmd_ctxt++) {
+		struct mhi_ring *ring = &mhi_cmd->ring;
+
+		ring->el_size = sizeof(struct mhi_ring_element);
+		ring->elements = CMD_EL_PER_RING;
+		ring->len = ring->el_size * ring->elements;
+		ret = mhi_alloc_aligned_ring(mhi_cntrl, ring, ring->len);
+		if (ret)
+			goto error_alloc_cmd;
+
+		ring->rp = ring->wp = ring->base;
+		cmd_ctxt->rbase = cpu_to_le64(ring->iommu_base);
+		cmd_ctxt->rp = cmd_ctxt->wp = cmd_ctxt->rbase;
+		cmd_ctxt->rlen = cpu_to_le64(ring->len);
+		ring->ctxt_wp = &cmd_ctxt->wp;
+	}
+
+	mhi_cntrl->mhi_ctxt = mhi_ctxt;
+
+	return 0;
+
+error_alloc_cmd:
+	for (--i, --mhi_cmd; i >= 0; i--, mhi_cmd--) {
+		struct mhi_ring *ring = &mhi_cmd->ring;
+
+		dma_free_coherent(mhi_cntrl->cntrl_dev, ring->alloc_size,
+				  ring->pre_aligned, ring->dma_handle);
+	}
+	dma_free_coherent(mhi_cntrl->cntrl_dev,
+			  sizeof(*mhi_ctxt->cmd_ctxt) * NR_OF_CMD_RINGS,
+			  mhi_ctxt->cmd_ctxt, mhi_ctxt->cmd_ctxt_addr);
+	i = mhi_cntrl->total_ev_rings;
+	mhi_event = mhi_cntrl->mhi_event + i;
+
+error_alloc_er:
+	for (--i, --mhi_event; i >= 0; i--, mhi_event--) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		if (mhi_event->offload_ev)
+			continue;
+
+		dma_free_coherent(mhi_cntrl->cntrl_dev, ring->alloc_size,
+				  ring->pre_aligned, ring->dma_handle);
+	}
+	dma_free_coherent(mhi_cntrl->cntrl_dev, sizeof(*mhi_ctxt->er_ctxt) *
+			  mhi_cntrl->total_ev_rings, mhi_ctxt->er_ctxt,
+			  mhi_ctxt->er_ctxt_addr);
+
+error_alloc_er_ctxt:
+	dma_free_coherent(mhi_cntrl->cntrl_dev, sizeof(*mhi_ctxt->chan_ctxt) *
+			  mhi_cntrl->max_chan, mhi_ctxt->chan_ctxt,
+			  mhi_ctxt->chan_ctxt_addr);
+
+error_alloc_chan_ctxt:
+	kfree(mhi_ctxt);
+
+	return ret;
+}
+
+int mhi_init_mmio(struct mhi_controller *mhi_cntrl)
+{
+	u32 val;
+	int i, ret;
+	struct mhi_chan *mhi_chan;
+	struct mhi_event *mhi_event;
+	void __iomem *base = mhi_cntrl->regs;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	struct {
+		u32 offset;
+		u32 mask;
+		u32 shift;
+		u32 val;
+	} reg_info[] = {
+		{
+			CCABAP_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->mhi_ctxt->chan_ctxt_addr),
+		},
+		{
+			CCABAP_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->mhi_ctxt->chan_ctxt_addr),
+		},
+		{
+			ECABAP_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->mhi_ctxt->er_ctxt_addr),
+		},
+		{
+			ECABAP_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->mhi_ctxt->er_ctxt_addr),
+		},
+		{
+			CRCBAP_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->mhi_ctxt->cmd_ctxt_addr),
+		},
+		{
+			CRCBAP_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->mhi_ctxt->cmd_ctxt_addr),
+		},
+		{
+			MHICFG, MHICFG_NER_MASK, MHICFG_NER_SHIFT,
+			mhi_cntrl->total_ev_rings,
+		},
+		{
+			MHICFG, MHICFG_NHWER_MASK, MHICFG_NHWER_SHIFT,
+			mhi_cntrl->hw_ev_rings,
+		},
+		{
+			MHICTRLBASE_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->iova_start),
+		},
+		{
+			MHICTRLBASE_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->iova_start),
+		},
+		{
+			MHIDATABASE_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->iova_start),
+		},
+		{
+			MHIDATABASE_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->iova_start),
+		},
+		{
+			MHICTRLLIMIT_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->iova_stop),
+		},
+		{
+			MHICTRLLIMIT_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->iova_stop),
+		},
+		{
+			MHIDATALIMIT_HIGHER, U32_MAX, 0,
+			upper_32_bits(mhi_cntrl->iova_stop),
+		},
+		{
+			MHIDATALIMIT_LOWER, U32_MAX, 0,
+			lower_32_bits(mhi_cntrl->iova_stop),
+		},
+		{ 0, 0, 0 }
+	};
+
+	dev_dbg(dev, "Initializing MHI registers\n");
+
+	/* Read channel db offset */
+	ret = mhi_read_reg_field(mhi_cntrl, base, CHDBOFF, CHDBOFF_CHDBOFF_MASK,
+				 CHDBOFF_CHDBOFF_SHIFT, &val);
+	if (ret) {
+		dev_err(dev, "Unable to read CHDBOFF register\n");
+		return -EIO;
+	}
+
+	if (val >= mhi_cntrl->reg_len - (8 * MHI_DEV_WAKE_DB)) {
+		dev_err(dev, "CHDB offset: 0x%x is out of range: 0x%zx\n",
+			val, mhi_cntrl->reg_len - (8 * MHI_DEV_WAKE_DB));
+		return -ERANGE;
+	}
+
+	/* Setup wake db */
+	mhi_cntrl->wake_db = base + val + (8 * MHI_DEV_WAKE_DB);
+	mhi_cntrl->wake_set = false;
+
+	/* Setup channel db address for each channel in tre_ring */
+	mhi_chan = mhi_cntrl->mhi_chan;
+	for (i = 0; i < mhi_cntrl->max_chan; i++, val += 8, mhi_chan++)
+		mhi_chan->tre_ring.db_addr = base + val;
+
+	/* Read event ring db offset */
+	ret = mhi_read_reg_field(mhi_cntrl, base, ERDBOFF, ERDBOFF_ERDBOFF_MASK,
+				 ERDBOFF_ERDBOFF_SHIFT, &val);
+	if (ret) {
+		dev_err(dev, "Unable to read ERDBOFF register\n");
+		return -EIO;
+	}
+
+	if (val >= mhi_cntrl->reg_len - (8 * mhi_cntrl->total_ev_rings)) {
+		dev_err(dev, "ERDB offset: 0x%x is out of range: 0x%zx\n",
+			val, mhi_cntrl->reg_len - (8 * mhi_cntrl->total_ev_rings));
+		return -ERANGE;
+	}
+
+	/* Setup event db address for each ev_ring */
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, val += 8, mhi_event++) {
+		if (mhi_event->offload_ev)
+			continue;
+
+		mhi_event->ring.db_addr = base + val;
+	}
+
+	/* Setup DB register for primary CMD rings */
+	mhi_cntrl->mhi_cmd[PRIMARY_CMD_RING].ring.db_addr = base + CRDB_LOWER;
+
+	/* Write to MMIO registers */
+	for (i = 0; reg_info[i].offset; i++)
+		mhi_write_reg_field(mhi_cntrl, base, reg_info[i].offset,
+				    reg_info[i].mask, reg_info[i].shift,
+				    reg_info[i].val);
+
+	return 0;
+}
+
+void mhi_deinit_chan_ctxt(struct mhi_controller *mhi_cntrl,
+			  struct mhi_chan *mhi_chan)
+{
+	struct mhi_ring *buf_ring;
+	struct mhi_ring *tre_ring;
+	struct mhi_chan_ctxt *chan_ctxt;
+	u32 tmp;
+
+	buf_ring = &mhi_chan->buf_ring;
+	tre_ring = &mhi_chan->tre_ring;
+	chan_ctxt = &mhi_cntrl->mhi_ctxt->chan_ctxt[mhi_chan->chan];
+
+	if (!chan_ctxt->rbase) /* Already uninitialized */
+		return;
+
+	dma_free_coherent(mhi_cntrl->cntrl_dev, tre_ring->alloc_size,
+			  tre_ring->pre_aligned, tre_ring->dma_handle);
+	vfree(buf_ring->base);
+
+	buf_ring->base = tre_ring->base = NULL;
+	tre_ring->ctxt_wp = NULL;
+	chan_ctxt->rbase = 0;
+	chan_ctxt->rlen = 0;
+	chan_ctxt->rp = 0;
+	chan_ctxt->wp = 0;
+
+	tmp = le32_to_cpu(chan_ctxt->chcfg);
+	tmp &= ~CHAN_CTX_CHSTATE_MASK;
+	tmp |= (MHI_CH_STATE_DISABLED << CHAN_CTX_CHSTATE_SHIFT);
+	chan_ctxt->chcfg = cpu_to_le32(tmp);
+
+	/* Update to all cores */
+	smp_wmb();
+}
+
+int mhi_init_chan_ctxt(struct mhi_controller *mhi_cntrl,
+		       struct mhi_chan *mhi_chan)
+{
+	struct mhi_ring *buf_ring;
+	struct mhi_ring *tre_ring;
+	struct mhi_chan_ctxt *chan_ctxt;
+	u32 tmp;
+	int ret;
+
+	buf_ring = &mhi_chan->buf_ring;
+	tre_ring = &mhi_chan->tre_ring;
+	tre_ring->el_size = sizeof(struct mhi_ring_element);
+	tre_ring->len = tre_ring->el_size * tre_ring->elements;
+	chan_ctxt = &mhi_cntrl->mhi_ctxt->chan_ctxt[mhi_chan->chan];
+	ret = mhi_alloc_aligned_ring(mhi_cntrl, tre_ring, tre_ring->len);
+	if (ret)
+		return -ENOMEM;
+
+	buf_ring->el_size = sizeof(struct mhi_buf_info);
+	buf_ring->len = buf_ring->el_size * buf_ring->elements;
+	buf_ring->base = vzalloc(buf_ring->len);
+
+	if (!buf_ring->base) {
+		dma_free_coherent(mhi_cntrl->cntrl_dev, tre_ring->alloc_size,
+				  tre_ring->pre_aligned, tre_ring->dma_handle);
+		return -ENOMEM;
+	}
+
+	tmp = le32_to_cpu(chan_ctxt->chcfg);
+	tmp &= ~CHAN_CTX_CHSTATE_MASK;
+	tmp |= (MHI_CH_STATE_ENABLED << CHAN_CTX_CHSTATE_SHIFT);
+	chan_ctxt->chcfg = cpu_to_le32(tmp);
+
+	chan_ctxt->rbase = cpu_to_le64(tre_ring->iommu_base);
+	chan_ctxt->rp = chan_ctxt->wp = chan_ctxt->rbase;
+	chan_ctxt->rlen = cpu_to_le64(tre_ring->len);
+	tre_ring->ctxt_wp = &chan_ctxt->wp;
+
+	tre_ring->rp = tre_ring->wp = tre_ring->base;
+	buf_ring->rp = buf_ring->wp = buf_ring->base;
+	mhi_chan->db_cfg.db_mode = 1;
+
+	/* Update to all cores */
+	smp_wmb();
+
+	return 0;
+}
+
+static int parse_ev_cfg(struct mhi_controller *mhi_cntrl,
+			const struct mhi_controller_config *config)
+{
+	struct mhi_event *mhi_event;
+	const struct mhi_event_config *event_cfg;
+	struct device *dev = mhi_cntrl->cntrl_dev;
+	int i, num;
+
+	num = config->num_events;
+	mhi_cntrl->total_ev_rings = num;
+	mhi_cntrl->mhi_event = kcalloc(num, sizeof(*mhi_cntrl->mhi_event),
+				       GFP_KERNEL);
+	if (!mhi_cntrl->mhi_event)
+		return -ENOMEM;
+
+	/* Populate event ring */
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < num; i++) {
+		event_cfg = &config->event_cfg[i];
+
+		mhi_event->er_index = i;
+		mhi_event->ring.elements = event_cfg->num_elements;
+		mhi_event->intmod = event_cfg->irq_moderation_ms;
+		mhi_event->irq = event_cfg->irq;
+
+		if (event_cfg->channel != U32_MAX) {
+			/* This event ring has a dedicated channel */
+			mhi_event->chan = event_cfg->channel;
+			if (mhi_event->chan >= mhi_cntrl->max_chan) {
+				dev_err(dev,
+					"Event Ring channel not available\n");
+				goto error_ev_cfg;
+			}
+
+			mhi_event->mhi_chan =
+				&mhi_cntrl->mhi_chan[mhi_event->chan];
+		}
+
+		/* Priority is fixed to 1 for now */
+		mhi_event->priority = 1;
+
+		mhi_event->db_cfg.brstmode = event_cfg->mode;
+		if (MHI_INVALID_BRSTMODE(mhi_event->db_cfg.brstmode))
+			goto error_ev_cfg;
+
+		if (mhi_event->db_cfg.brstmode == MHI_DB_BRST_ENABLE)
+			mhi_event->db_cfg.process_db = mhi_db_brstmode;
+		else
+			mhi_event->db_cfg.process_db = mhi_db_brstmode_disable;
+
+		mhi_event->data_type = event_cfg->data_type;
+
+		switch (mhi_event->data_type) {
+		case MHI_ER_DATA:
+			mhi_event->process_event = mhi_process_data_event_ring;
+			break;
+		case MHI_ER_CTRL:
+			mhi_event->process_event = mhi_process_ctrl_ev_ring;
+			break;
+		default:
+			dev_err(dev, "Event Ring type not supported\n");
+			goto error_ev_cfg;
+		}
+
+		mhi_event->hw_ring = event_cfg->hardware_event;
+		if (mhi_event->hw_ring)
+			mhi_cntrl->hw_ev_rings++;
+		else
+			mhi_cntrl->sw_ev_rings++;
+
+		mhi_event->cl_manage = event_cfg->client_managed;
+		mhi_event->offload_ev = event_cfg->offload_channel;
+		mhi_event++;
+	}
+
+	return 0;
+
+error_ev_cfg:
+
+	kfree(mhi_cntrl->mhi_event);
+	return -EINVAL;
+}
+
+static int parse_ch_cfg(struct mhi_controller *mhi_cntrl,
+			const struct mhi_controller_config *config)
+{
+	const struct mhi_channel_config *ch_cfg;
+	struct device *dev = mhi_cntrl->cntrl_dev;
+	int i;
+	u32 chan;
+
+	mhi_cntrl->max_chan = config->max_channels;
+
+	/*
+	 * The allocation of MHI channels can exceed 32KB in some scenarios,
+	 * so to avoid any memory possible allocation failures, vzalloc is
+	 * used here
+	 */
+	mhi_cntrl->mhi_chan = vzalloc(mhi_cntrl->max_chan *
+				      sizeof(*mhi_cntrl->mhi_chan));
+	if (!mhi_cntrl->mhi_chan)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&mhi_cntrl->lpm_chans);
+
+	/* Populate channel configurations */
+	for (i = 0; i < config->num_channels; i++) {
+		struct mhi_chan *mhi_chan;
+
+		ch_cfg = &config->ch_cfg[i];
+
+		chan = ch_cfg->num;
+		if (chan >= mhi_cntrl->max_chan) {
+			dev_err(dev, "Channel %d not available\n", chan);
+			goto error_chan_cfg;
+		}
+
+		mhi_chan = &mhi_cntrl->mhi_chan[chan];
+		mhi_chan->name = ch_cfg->name;
+		mhi_chan->chan = chan;
+
+		mhi_chan->tre_ring.elements = ch_cfg->num_elements;
+		if (!mhi_chan->tre_ring.elements)
+			goto error_chan_cfg;
+
+		/*
+		 * For some channels, local ring length should be bigger than
+		 * the transfer ring length due to internal logical channels
+		 * in device. So host can queue much more buffers than transfer
+		 * ring length. Example, RSC channels should have a larger local
+		 * channel length than transfer ring length.
+		 */
+		mhi_chan->buf_ring.elements = ch_cfg->local_elements;
+		if (!mhi_chan->buf_ring.elements)
+			mhi_chan->buf_ring.elements = mhi_chan->tre_ring.elements;
+		mhi_chan->er_index = ch_cfg->event_ring;
+		mhi_chan->dir = ch_cfg->dir;
+
+		/*
+		 * For most channels, chtype is identical to channel directions.
+		 * So, if it is not defined then assign channel direction to
+		 * chtype
+		 */
+		mhi_chan->type = ch_cfg->type;
+		if (!mhi_chan->type)
+			mhi_chan->type = (enum mhi_ch_type)mhi_chan->dir;
+
+		mhi_chan->ee_mask = ch_cfg->ee_mask;
+		mhi_chan->db_cfg.pollcfg = ch_cfg->pollcfg;
+		mhi_chan->lpm_notify = ch_cfg->lpm_notify;
+		mhi_chan->offload_ch = ch_cfg->offload_channel;
+		mhi_chan->db_cfg.reset_req = ch_cfg->doorbell_mode_switch;
+		mhi_chan->pre_alloc = ch_cfg->auto_queue;
+		mhi_chan->wake_capable = ch_cfg->wake_capable;
+
+		/*
+		 * If MHI host allocates buffers, then the channel direction
+		 * should be DMA_FROM_DEVICE
+		 */
+		if (mhi_chan->pre_alloc && mhi_chan->dir != DMA_FROM_DEVICE) {
+			dev_err(dev, "Invalid channel configuration\n");
+			goto error_chan_cfg;
+		}
+
+		/*
+		 * Bi-directional and direction less channel must be an
+		 * offload channel
+		 */
+		if ((mhi_chan->dir == DMA_BIDIRECTIONAL ||
+		     mhi_chan->dir == DMA_NONE) && !mhi_chan->offload_ch) {
+			dev_err(dev, "Invalid channel configuration\n");
+			goto error_chan_cfg;
+		}
+
+		if (!mhi_chan->offload_ch) {
+			mhi_chan->db_cfg.brstmode = ch_cfg->doorbell;
+			if (MHI_INVALID_BRSTMODE(mhi_chan->db_cfg.brstmode)) {
+				dev_err(dev, "Invalid Door bell mode\n");
+				goto error_chan_cfg;
+			}
+		}
+
+		if (mhi_chan->db_cfg.brstmode == MHI_DB_BRST_ENABLE)
+			mhi_chan->db_cfg.process_db = mhi_db_brstmode;
+		else
+			mhi_chan->db_cfg.process_db = mhi_db_brstmode_disable;
+
+		mhi_chan->configured = true;
+
+		if (mhi_chan->lpm_notify)
+			list_add_tail(&mhi_chan->node, &mhi_cntrl->lpm_chans);
+	}
+
+	return 0;
+
+error_chan_cfg:
+	vfree(mhi_cntrl->mhi_chan);
+
+	return -EINVAL;
+}
+
+static int parse_config(struct mhi_controller *mhi_cntrl,
+			const struct mhi_controller_config *config)
+{
+	int ret;
+
+	/* Parse MHI channel configuration */
+	ret = parse_ch_cfg(mhi_cntrl, config);
+	if (ret)
+		return ret;
+
+	/* Parse MHI event configuration */
+	ret = parse_ev_cfg(mhi_cntrl, config);
+	if (ret)
+		goto error_ev_cfg;
+
+	mhi_cntrl->timeout_ms = config->timeout_ms;
+	if (!mhi_cntrl->timeout_ms)
+		mhi_cntrl->timeout_ms = MHI_TIMEOUT_MS;
+
+	mhi_cntrl->bounce_buf = config->use_bounce_buf;
+	mhi_cntrl->buffer_len = config->buf_len;
+	if (!mhi_cntrl->buffer_len)
+		mhi_cntrl->buffer_len = MHI_MAX_MTU;
+
+	/* By default, host is allowed to ring DB in both M0 and M2 states */
+	mhi_cntrl->db_access = MHI_PM_M0 | MHI_PM_M2;
+	if (config->m2_no_db)
+		mhi_cntrl->db_access &= ~MHI_PM_M2;
+
+	return 0;
+
+error_ev_cfg:
+	vfree(mhi_cntrl->mhi_chan);
+
+	return ret;
+}
+
+int mhi_register_controller(struct mhi_controller *mhi_cntrl,
+			    const struct mhi_controller_config *config)
+{
+	struct mhi_event *mhi_event;
+	struct mhi_chan *mhi_chan;
+	struct mhi_cmd *mhi_cmd;
+	struct mhi_device *mhi_dev;
+	u32 soc_info;
+	int ret, i;
+
+	if (!mhi_cntrl || !mhi_cntrl->cntrl_dev || !mhi_cntrl->regs ||
+	    !mhi_cntrl->runtime_get || !mhi_cntrl->runtime_put ||
+	    !mhi_cntrl->status_cb || !mhi_cntrl->read_reg ||
+	    !mhi_cntrl->write_reg || !mhi_cntrl->nr_irqs ||
+	    !mhi_cntrl->irq || !mhi_cntrl->reg_len)
+		return -EINVAL;
+
+	ret = parse_config(mhi_cntrl, config);
+	if (ret)
+		return -EINVAL;
+
+	mhi_cntrl->mhi_cmd = kcalloc(NR_OF_CMD_RINGS,
+				     sizeof(*mhi_cntrl->mhi_cmd), GFP_KERNEL);
+	if (!mhi_cntrl->mhi_cmd) {
+		ret = -ENOMEM;
+		goto err_free_event;
+	}
+
+	INIT_LIST_HEAD(&mhi_cntrl->transition_list);
+	mutex_init(&mhi_cntrl->pm_mutex);
+	rwlock_init(&mhi_cntrl->pm_lock);
+	spin_lock_init(&mhi_cntrl->transition_lock);
+	spin_lock_init(&mhi_cntrl->wlock);
+	INIT_WORK(&mhi_cntrl->st_worker, mhi_pm_st_worker);
+	init_waitqueue_head(&mhi_cntrl->state_event);
+
+	mhi_cntrl->hiprio_wq = alloc_ordered_workqueue("mhi_hiprio_wq", WQ_HIGHPRI);
+	if (!mhi_cntrl->hiprio_wq) {
+		dev_err(mhi_cntrl->cntrl_dev, "Failed to allocate workqueue\n");
+		ret = -ENOMEM;
+		goto err_free_cmd;
+	}
+
+	mhi_cmd = mhi_cntrl->mhi_cmd;
+	for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++)
+		spin_lock_init(&mhi_cmd->lock);
+
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		/* Skip for offload events */
+		if (mhi_event->offload_ev)
+			continue;
+
+		mhi_event->mhi_cntrl = mhi_cntrl;
+		spin_lock_init(&mhi_event->lock);
+		if (mhi_event->data_type == MHI_ER_CTRL)
+			tasklet_init(&mhi_event->task, mhi_ctrl_ev_task,
+				     (ulong)mhi_event);
+		else
+			tasklet_init(&mhi_event->task, mhi_ev_task,
+				     (ulong)mhi_event);
+	}
+
+	mhi_chan = mhi_cntrl->mhi_chan;
+	for (i = 0; i < mhi_cntrl->max_chan; i++, mhi_chan++) {
+		mutex_init(&mhi_chan->mutex);
+		init_completion(&mhi_chan->completion);
+		rwlock_init(&mhi_chan->lock);
+
+		/* used in setting bei field of TRE */
+		mhi_event = &mhi_cntrl->mhi_event[mhi_chan->er_index];
+		mhi_chan->intmod = mhi_event->intmod;
+	}
+
+	if (mhi_cntrl->bounce_buf) {
+		mhi_cntrl->map_single = mhi_map_single_use_bb;
+		mhi_cntrl->unmap_single = mhi_unmap_single_use_bb;
+	} else {
+		mhi_cntrl->map_single = mhi_map_single_no_bb;
+		mhi_cntrl->unmap_single = mhi_unmap_single_no_bb;
+	}
+
+	/* Read the MHI device info */
+	ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->regs,
+			   SOC_HW_VERSION_OFFS, &soc_info);
+	if (ret)
+		goto err_destroy_wq;
+
+	mhi_cntrl->family_number = (soc_info & SOC_HW_VERSION_FAM_NUM_BMSK) >>
+					SOC_HW_VERSION_FAM_NUM_SHFT;
+	mhi_cntrl->device_number = (soc_info & SOC_HW_VERSION_DEV_NUM_BMSK) >>
+					SOC_HW_VERSION_DEV_NUM_SHFT;
+	mhi_cntrl->major_version = (soc_info & SOC_HW_VERSION_MAJOR_VER_BMSK) >>
+					SOC_HW_VERSION_MAJOR_VER_SHFT;
+	mhi_cntrl->minor_version = (soc_info & SOC_HW_VERSION_MINOR_VER_BMSK) >>
+					SOC_HW_VERSION_MINOR_VER_SHFT;
+
+	mhi_cntrl->index = ida_alloc(&mhi_controller_ida, GFP_KERNEL);
+	if (mhi_cntrl->index < 0) {
+		ret = mhi_cntrl->index;
+		goto err_destroy_wq;
+	}
+
+	/* Register controller with MHI bus */
+	mhi_dev = mhi_alloc_device(mhi_cntrl);
+	if (IS_ERR(mhi_dev)) {
+		dev_err(mhi_cntrl->cntrl_dev, "Failed to allocate MHI device\n");
+		ret = PTR_ERR(mhi_dev);
+		goto err_ida_free;
+	}
+
+	mhi_dev->dev_type = MHI_DEVICE_CONTROLLER;
+	mhi_dev->mhi_cntrl = mhi_cntrl;
+	dev_set_name(&mhi_dev->dev, "mhi%d", mhi_cntrl->index);
+	mhi_dev->name = dev_name(&mhi_dev->dev);
+
+	/* Init wakeup source */
+	device_init_wakeup(&mhi_dev->dev, true);
+
+	ret = device_add(&mhi_dev->dev);
+	if (ret)
+		goto err_release_dev;
+
+	mhi_cntrl->mhi_dev = mhi_dev;
+
+	mhi_create_debugfs(mhi_cntrl);
+
+	return 0;
+
+err_release_dev:
+	put_device(&mhi_dev->dev);
+err_ida_free:
+	ida_free(&mhi_controller_ida, mhi_cntrl->index);
+err_destroy_wq:
+	destroy_workqueue(mhi_cntrl->hiprio_wq);
+err_free_cmd:
+	kfree(mhi_cntrl->mhi_cmd);
+err_free_event:
+	kfree(mhi_cntrl->mhi_event);
+	vfree(mhi_cntrl->mhi_chan);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_register_controller);
+
+void mhi_unregister_controller(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_device *mhi_dev = mhi_cntrl->mhi_dev;
+	struct mhi_chan *mhi_chan = mhi_cntrl->mhi_chan;
+	unsigned int i;
+
+	mhi_destroy_debugfs(mhi_cntrl);
+
+	destroy_workqueue(mhi_cntrl->hiprio_wq);
+	kfree(mhi_cntrl->mhi_cmd);
+	kfree(mhi_cntrl->mhi_event);
+
+	/* Drop the references to MHI devices created for channels */
+	for (i = 0; i < mhi_cntrl->max_chan; i++, mhi_chan++) {
+		if (!mhi_chan->mhi_dev)
+			continue;
+
+		put_device(&mhi_chan->mhi_dev->dev);
+	}
+	vfree(mhi_cntrl->mhi_chan);
+
+	device_del(&mhi_dev->dev);
+	put_device(&mhi_dev->dev);
+
+	ida_free(&mhi_controller_ida, mhi_cntrl->index);
+}
+EXPORT_SYMBOL_GPL(mhi_unregister_controller);
+
+struct mhi_controller *mhi_alloc_controller(void)
+{
+	struct mhi_controller *mhi_cntrl;
+
+	mhi_cntrl = kzalloc(sizeof(*mhi_cntrl), GFP_KERNEL);
+
+	return mhi_cntrl;
+}
+EXPORT_SYMBOL_GPL(mhi_alloc_controller);
+
+void mhi_free_controller(struct mhi_controller *mhi_cntrl)
+{
+	kfree(mhi_cntrl);
+}
+EXPORT_SYMBOL_GPL(mhi_free_controller);
+
+int mhi_prepare_for_power_up(struct mhi_controller *mhi_cntrl)
+{
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	u32 bhi_off, bhie_off;
+	int ret;
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+
+	ret = mhi_init_dev_ctxt(mhi_cntrl);
+	if (ret)
+		goto error_dev_ctxt;
+
+	ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->regs, BHIOFF, &bhi_off);
+	if (ret) {
+		dev_err(dev, "Error getting BHI offset\n");
+		goto error_reg_offset;
+	}
+
+	if (bhi_off >= mhi_cntrl->reg_len) {
+		dev_err(dev, "BHI offset: 0x%x is out of range: 0x%zx\n",
+			bhi_off, mhi_cntrl->reg_len);
+		ret = -EINVAL;
+		goto error_reg_offset;
+	}
+	mhi_cntrl->bhi = mhi_cntrl->regs + bhi_off;
+
+	if (mhi_cntrl->fbc_download || mhi_cntrl->rddm_size) {
+		ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->regs, BHIEOFF,
+				   &bhie_off);
+		if (ret) {
+			dev_err(dev, "Error getting BHIE offset\n");
+			goto error_reg_offset;
+		}
+
+		if (bhie_off >= mhi_cntrl->reg_len) {
+			dev_err(dev,
+				"BHIe offset: 0x%x is out of range: 0x%zx\n",
+				bhie_off, mhi_cntrl->reg_len);
+			ret = -EINVAL;
+			goto error_reg_offset;
+		}
+		mhi_cntrl->bhie = mhi_cntrl->regs + bhie_off;
+	}
+
+	if (mhi_cntrl->rddm_size) {
+		/*
+		 * This controller supports RDDM, so we need to manually clear
+		 * BHIE RX registers since POR values are undefined.
+		 */
+		memset_io(mhi_cntrl->bhie + BHIE_RXVECADDR_LOW_OFFS,
+			  0, BHIE_RXVECSTATUS_OFFS - BHIE_RXVECADDR_LOW_OFFS +
+			  4);
+		/*
+		 * Allocate RDDM table for debugging purpose if specified
+		 */
+		mhi_alloc_bhie_table(mhi_cntrl, &mhi_cntrl->rddm_image,
+				     mhi_cntrl->rddm_size);
+		if (mhi_cntrl->rddm_image)
+			mhi_rddm_prepare(mhi_cntrl, mhi_cntrl->rddm_image);
+	}
+
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+
+	return 0;
+
+error_reg_offset:
+	mhi_deinit_dev_ctxt(mhi_cntrl);
+
+error_dev_ctxt:
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_prepare_for_power_up);
+
+void mhi_unprepare_after_power_down(struct mhi_controller *mhi_cntrl)
+{
+	if (mhi_cntrl->fbc_image) {
+		mhi_free_bhie_table(mhi_cntrl, mhi_cntrl->fbc_image);
+		mhi_cntrl->fbc_image = NULL;
+	}
+
+	if (mhi_cntrl->rddm_image) {
+		mhi_free_bhie_table(mhi_cntrl, mhi_cntrl->rddm_image);
+		mhi_cntrl->rddm_image = NULL;
+	}
+
+	mhi_cntrl->bhi = NULL;
+	mhi_cntrl->bhie = NULL;
+
+	mhi_deinit_dev_ctxt(mhi_cntrl);
+}
+EXPORT_SYMBOL_GPL(mhi_unprepare_after_power_down);
+
+static void mhi_release_device(struct device *dev)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+
+	/*
+	 * We need to set the mhi_chan->mhi_dev to NULL here since the MHI
+	 * devices for the channels will only get created if the mhi_dev
+	 * associated with it is NULL. This scenario will happen during the
+	 * controller suspend and resume.
+	 */
+	if (mhi_dev->ul_chan)
+		mhi_dev->ul_chan->mhi_dev = NULL;
+
+	if (mhi_dev->dl_chan)
+		mhi_dev->dl_chan->mhi_dev = NULL;
+
+	kfree(mhi_dev);
+}
+
+struct mhi_device *mhi_alloc_device(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_device *mhi_dev;
+	struct device *dev;
+
+	mhi_dev = kzalloc(sizeof(*mhi_dev), GFP_KERNEL);
+	if (!mhi_dev)
+		return ERR_PTR(-ENOMEM);
+
+	dev = &mhi_dev->dev;
+	device_initialize(dev);
+	dev->bus = &mhi_bus_type;
+	dev->release = mhi_release_device;
+
+	if (mhi_cntrl->mhi_dev) {
+		/* for MHI client devices, parent is the MHI controller device */
+		dev->parent = &mhi_cntrl->mhi_dev->dev;
+	} else {
+		/* for MHI controller device, parent is the bus device (e.g. pci device) */
+		dev->parent = mhi_cntrl->cntrl_dev;
+	}
+
+	mhi_dev->mhi_cntrl = mhi_cntrl;
+	mhi_dev->dev_wake = 0;
+
+	return mhi_dev;
+}
+
+static int mhi_driver_probe(struct device *dev)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct device_driver *drv = dev->driver;
+	struct mhi_driver *mhi_drv = to_mhi_driver(drv);
+	struct mhi_event *mhi_event;
+	struct mhi_chan *ul_chan = mhi_dev->ul_chan;
+	struct mhi_chan *dl_chan = mhi_dev->dl_chan;
+	int ret;
+
+	/* Bring device out of LPM */
+	ret = mhi_device_get_sync(mhi_dev);
+	if (ret)
+		return ret;
+
+	ret = -EINVAL;
+
+	if (ul_chan) {
+		/*
+		 * If channel supports LPM notifications then status_cb should
+		 * be provided
+		 */
+		if (ul_chan->lpm_notify && !mhi_drv->status_cb)
+			goto exit_probe;
+
+		/* For non-offload channels then xfer_cb should be provided */
+		if (!ul_chan->offload_ch && !mhi_drv->ul_xfer_cb)
+			goto exit_probe;
+
+		ul_chan->xfer_cb = mhi_drv->ul_xfer_cb;
+	}
+
+	ret = -EINVAL;
+	if (dl_chan) {
+		/*
+		 * If channel supports LPM notifications then status_cb should
+		 * be provided
+		 */
+		if (dl_chan->lpm_notify && !mhi_drv->status_cb)
+			goto exit_probe;
+
+		/* For non-offload channels then xfer_cb should be provided */
+		if (!dl_chan->offload_ch && !mhi_drv->dl_xfer_cb)
+			goto exit_probe;
+
+		mhi_event = &mhi_cntrl->mhi_event[dl_chan->er_index];
+
+		/*
+		 * If the channel event ring is managed by client, then
+		 * status_cb must be provided so that the framework can
+		 * notify pending data
+		 */
+		if (mhi_event->cl_manage && !mhi_drv->status_cb)
+			goto exit_probe;
+
+		dl_chan->xfer_cb = mhi_drv->dl_xfer_cb;
+	}
+
+	/* Call the user provided probe function */
+	ret = mhi_drv->probe(mhi_dev, mhi_dev->id);
+	if (ret)
+		goto exit_probe;
+
+	mhi_device_put(mhi_dev);
+
+	return ret;
+
+exit_probe:
+	mhi_unprepare_from_transfer(mhi_dev);
+
+	mhi_device_put(mhi_dev);
+
+	return ret;
+}
+
+static int mhi_driver_remove(struct device *dev)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+	struct mhi_driver *mhi_drv = to_mhi_driver(dev->driver);
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan;
+	enum mhi_ch_state ch_state[] = {
+		MHI_CH_STATE_DISABLED,
+		MHI_CH_STATE_DISABLED
+	};
+	int dir;
+
+	/* Skip if it is a controller device */
+	if (mhi_dev->dev_type == MHI_DEVICE_CONTROLLER)
+		return 0;
+
+	/* Reset both channels */
+	for (dir = 0; dir < 2; dir++) {
+		mhi_chan = dir ? mhi_dev->ul_chan : mhi_dev->dl_chan;
+
+		if (!mhi_chan)
+			continue;
+
+		/* Wake all threads waiting for completion */
+		write_lock_irq(&mhi_chan->lock);
+		mhi_chan->ccs = MHI_EV_CC_INVALID;
+		complete_all(&mhi_chan->completion);
+		write_unlock_irq(&mhi_chan->lock);
+
+		/* Set the channel state to disabled */
+		mutex_lock(&mhi_chan->mutex);
+		write_lock_irq(&mhi_chan->lock);
+		ch_state[dir] = mhi_chan->ch_state;
+		mhi_chan->ch_state = MHI_CH_STATE_SUSPENDED;
+		write_unlock_irq(&mhi_chan->lock);
+
+		/* Reset the non-offload channel */
+		if (!mhi_chan->offload_ch)
+			mhi_reset_chan(mhi_cntrl, mhi_chan);
+
+		mutex_unlock(&mhi_chan->mutex);
+	}
+
+	mhi_drv->remove(mhi_dev);
+
+	/* De-init channel if it was enabled */
+	for (dir = 0; dir < 2; dir++) {
+		mhi_chan = dir ? mhi_dev->ul_chan : mhi_dev->dl_chan;
+
+		if (!mhi_chan)
+			continue;
+
+		mutex_lock(&mhi_chan->mutex);
+
+		if ((ch_state[dir] == MHI_CH_STATE_ENABLED ||
+		     ch_state[dir] == MHI_CH_STATE_STOP) &&
+		    !mhi_chan->offload_ch)
+			mhi_deinit_chan_ctxt(mhi_cntrl, mhi_chan);
+
+		mhi_chan->ch_state = MHI_CH_STATE_DISABLED;
+
+		mutex_unlock(&mhi_chan->mutex);
+	}
+
+	while (mhi_dev->dev_wake)
+		mhi_device_put(mhi_dev);
+
+	return 0;
+}
+
+int __mhi_driver_register(struct mhi_driver *mhi_drv, struct module *owner)
+{
+	struct device_driver *driver = &mhi_drv->driver;
+
+	if (!mhi_drv->probe || !mhi_drv->remove)
+		return -EINVAL;
+
+	driver->bus = &mhi_bus_type;
+	driver->owner = owner;
+	driver->probe = mhi_driver_probe;
+	driver->remove = mhi_driver_remove;
+
+	return driver_register(driver);
+}
+EXPORT_SYMBOL_GPL(__mhi_driver_register);
+
+void mhi_driver_unregister(struct mhi_driver *mhi_drv)
+{
+	driver_unregister(&mhi_drv->driver);
+}
+EXPORT_SYMBOL_GPL(mhi_driver_unregister);
+
+static int mhi_uevent(struct device *dev, struct kobj_uevent_env *env)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+
+	return add_uevent_var(env, "MODALIAS=" MHI_DEVICE_MODALIAS_FMT,
+					mhi_dev->name);
+}
+
+static int mhi_match(struct device *dev, struct device_driver *drv)
+{
+	struct mhi_device *mhi_dev = to_mhi_device(dev);
+	struct mhi_driver *mhi_drv = to_mhi_driver(drv);
+	const struct mhi_device_id *id;
+
+	/*
+	 * If the device is a controller type then there is no client driver
+	 * associated with it
+	 */
+	if (mhi_dev->dev_type == MHI_DEVICE_CONTROLLER)
+		return 0;
+
+	for (id = mhi_drv->id_table; id->chan[0]; id++)
+		if (!strcmp(mhi_dev->name, id->chan)) {
+			mhi_dev->id = id;
+			return 1;
+		}
+
+	return 0;
+};
+
+struct bus_type mhi_bus_type = {
+	.name = "mhi",
+	.dev_name = "mhi",
+	.match = mhi_match,
+	.uevent = mhi_uevent,
+	.dev_groups = mhi_dev_groups,
+};
+
+static int __init mhi_init(void)
+{
+	mhi_debugfs_init();
+	return bus_register(&mhi_bus_type);
+}
+
+static void __exit mhi_exit(void)
+{
+	mhi_debugfs_exit();
+	bus_unregister(&mhi_bus_type);
+}
+
+postcore_initcall(mhi_init);
+module_exit(mhi_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("MHI Host Interface");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/internal.h
@@ -0,0 +1,718 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#ifndef _MHI_INT_H
+#define _MHI_INT_H
+
+#include <linux/mhi.h>
+
+extern struct bus_type mhi_bus_type;
+
+#define MHIREGLEN (0x0)
+#define MHIREGLEN_MHIREGLEN_MASK (0xFFFFFFFF)
+#define MHIREGLEN_MHIREGLEN_SHIFT (0)
+
+#define MHIVER (0x8)
+#define MHIVER_MHIVER_MASK (0xFFFFFFFF)
+#define MHIVER_MHIVER_SHIFT (0)
+
+#define MHICFG (0x10)
+#define MHICFG_NHWER_MASK (0xFF000000)
+#define MHICFG_NHWER_SHIFT (24)
+#define MHICFG_NER_MASK (0xFF0000)
+#define MHICFG_NER_SHIFT (16)
+#define MHICFG_NHWCH_MASK (0xFF00)
+#define MHICFG_NHWCH_SHIFT (8)
+#define MHICFG_NCH_MASK (0xFF)
+#define MHICFG_NCH_SHIFT (0)
+
+#define CHDBOFF (0x18)
+#define CHDBOFF_CHDBOFF_MASK (0xFFFFFFFF)
+#define CHDBOFF_CHDBOFF_SHIFT (0)
+
+#define ERDBOFF (0x20)
+#define ERDBOFF_ERDBOFF_MASK (0xFFFFFFFF)
+#define ERDBOFF_ERDBOFF_SHIFT (0)
+
+#define BHIOFF (0x28)
+#define BHIOFF_BHIOFF_MASK (0xFFFFFFFF)
+#define BHIOFF_BHIOFF_SHIFT (0)
+
+#define BHIEOFF (0x2C)
+#define BHIEOFF_BHIEOFF_MASK (0xFFFFFFFF)
+#define BHIEOFF_BHIEOFF_SHIFT (0)
+
+#define DEBUGOFF (0x30)
+#define DEBUGOFF_DEBUGOFF_MASK (0xFFFFFFFF)
+#define DEBUGOFF_DEBUGOFF_SHIFT (0)
+
+#define MHICTRL (0x38)
+#define MHICTRL_MHISTATE_MASK (0x0000FF00)
+#define MHICTRL_MHISTATE_SHIFT (8)
+#define MHICTRL_RESET_MASK (0x2)
+#define MHICTRL_RESET_SHIFT (1)
+
+#define MHISTATUS (0x48)
+#define MHISTATUS_MHISTATE_MASK (0x0000FF00)
+#define MHISTATUS_MHISTATE_SHIFT (8)
+#define MHISTATUS_SYSERR_MASK (0x4)
+#define MHISTATUS_SYSERR_SHIFT (2)
+#define MHISTATUS_READY_MASK (0x1)
+#define MHISTATUS_READY_SHIFT (0)
+
+#define CCABAP_LOWER (0x58)
+#define CCABAP_LOWER_CCABAP_LOWER_MASK (0xFFFFFFFF)
+#define CCABAP_LOWER_CCABAP_LOWER_SHIFT (0)
+
+#define CCABAP_HIGHER (0x5C)
+#define CCABAP_HIGHER_CCABAP_HIGHER_MASK (0xFFFFFFFF)
+#define CCABAP_HIGHER_CCABAP_HIGHER_SHIFT (0)
+
+#define ECABAP_LOWER (0x60)
+#define ECABAP_LOWER_ECABAP_LOWER_MASK (0xFFFFFFFF)
+#define ECABAP_LOWER_ECABAP_LOWER_SHIFT (0)
+
+#define ECABAP_HIGHER (0x64)
+#define ECABAP_HIGHER_ECABAP_HIGHER_MASK (0xFFFFFFFF)
+#define ECABAP_HIGHER_ECABAP_HIGHER_SHIFT (0)
+
+#define CRCBAP_LOWER (0x68)
+#define CRCBAP_LOWER_CRCBAP_LOWER_MASK (0xFFFFFFFF)
+#define CRCBAP_LOWER_CRCBAP_LOWER_SHIFT (0)
+
+#define CRCBAP_HIGHER (0x6C)
+#define CRCBAP_HIGHER_CRCBAP_HIGHER_MASK (0xFFFFFFFF)
+#define CRCBAP_HIGHER_CRCBAP_HIGHER_SHIFT (0)
+
+#define CRDB_LOWER (0x70)
+#define CRDB_LOWER_CRDB_LOWER_MASK (0xFFFFFFFF)
+#define CRDB_LOWER_CRDB_LOWER_SHIFT (0)
+
+#define CRDB_HIGHER (0x74)
+#define CRDB_HIGHER_CRDB_HIGHER_MASK (0xFFFFFFFF)
+#define CRDB_HIGHER_CRDB_HIGHER_SHIFT (0)
+
+#define MHICTRLBASE_LOWER (0x80)
+#define MHICTRLBASE_LOWER_MHICTRLBASE_LOWER_MASK (0xFFFFFFFF)
+#define MHICTRLBASE_LOWER_MHICTRLBASE_LOWER_SHIFT (0)
+
+#define MHICTRLBASE_HIGHER (0x84)
+#define MHICTRLBASE_HIGHER_MHICTRLBASE_HIGHER_MASK (0xFFFFFFFF)
+#define MHICTRLBASE_HIGHER_MHICTRLBASE_HIGHER_SHIFT (0)
+
+#define MHICTRLLIMIT_LOWER (0x88)
+#define MHICTRLLIMIT_LOWER_MHICTRLLIMIT_LOWER_MASK (0xFFFFFFFF)
+#define MHICTRLLIMIT_LOWER_MHICTRLLIMIT_LOWER_SHIFT (0)
+
+#define MHICTRLLIMIT_HIGHER (0x8C)
+#define MHICTRLLIMIT_HIGHER_MHICTRLLIMIT_HIGHER_MASK (0xFFFFFFFF)
+#define MHICTRLLIMIT_HIGHER_MHICTRLLIMIT_HIGHER_SHIFT (0)
+
+#define MHIDATABASE_LOWER (0x98)
+#define MHIDATABASE_LOWER_MHIDATABASE_LOWER_MASK (0xFFFFFFFF)
+#define MHIDATABASE_LOWER_MHIDATABASE_LOWER_SHIFT (0)
+
+#define MHIDATABASE_HIGHER (0x9C)
+#define MHIDATABASE_HIGHER_MHIDATABASE_HIGHER_MASK (0xFFFFFFFF)
+#define MHIDATABASE_HIGHER_MHIDATABASE_HIGHER_SHIFT (0)
+
+#define MHIDATALIMIT_LOWER (0xA0)
+#define MHIDATALIMIT_LOWER_MHIDATALIMIT_LOWER_MASK (0xFFFFFFFF)
+#define MHIDATALIMIT_LOWER_MHIDATALIMIT_LOWER_SHIFT (0)
+
+#define MHIDATALIMIT_HIGHER (0xA4)
+#define MHIDATALIMIT_HIGHER_MHIDATALIMIT_HIGHER_MASK (0xFFFFFFFF)
+#define MHIDATALIMIT_HIGHER_MHIDATALIMIT_HIGHER_SHIFT (0)
+
+/* Host request register */
+#define MHI_SOC_RESET_REQ_OFFSET (0xB0)
+#define MHI_SOC_RESET_REQ BIT(0)
+
+/* MHI BHI offfsets */
+#define BHI_BHIVERSION_MINOR (0x00)
+#define BHI_BHIVERSION_MAJOR (0x04)
+#define BHI_IMGADDR_LOW (0x08)
+#define BHI_IMGADDR_HIGH (0x0C)
+#define BHI_IMGSIZE (0x10)
+#define BHI_RSVD1 (0x14)
+#define BHI_IMGTXDB (0x18)
+#define BHI_TXDB_SEQNUM_BMSK (0x3FFFFFFF)
+#define BHI_TXDB_SEQNUM_SHFT (0)
+#define BHI_RSVD2 (0x1C)
+#define BHI_INTVEC (0x20)
+#define BHI_RSVD3 (0x24)
+#define BHI_EXECENV (0x28)
+#define BHI_STATUS (0x2C)
+#define BHI_ERRCODE (0x30)
+#define BHI_ERRDBG1 (0x34)
+#define BHI_ERRDBG2 (0x38)
+#define BHI_ERRDBG3 (0x3C)
+#define BHI_SERIALNU (0x40)
+#define BHI_SBLANTIROLLVER (0x44)
+#define BHI_NUMSEG (0x48)
+#define BHI_MSMHWID(n) (0x4C + (0x4 * (n)))
+#define BHI_OEMPKHASH(n) (0x64 + (0x4 * (n)))
+#define BHI_RSVD5 (0xC4)
+#define BHI_STATUS_MASK (0xC0000000)
+#define BHI_STATUS_SHIFT (30)
+#define BHI_STATUS_ERROR (3)
+#define BHI_STATUS_SUCCESS (2)
+#define BHI_STATUS_RESET (0)
+
+/* MHI BHIE offsets */
+#define BHIE_MSMSOCID_OFFS (0x0000)
+#define BHIE_TXVECADDR_LOW_OFFS (0x002C)
+#define BHIE_TXVECADDR_HIGH_OFFS (0x0030)
+#define BHIE_TXVECSIZE_OFFS (0x0034)
+#define BHIE_TXVECDB_OFFS (0x003C)
+#define BHIE_TXVECDB_SEQNUM_BMSK (0x3FFFFFFF)
+#define BHIE_TXVECDB_SEQNUM_SHFT (0)
+#define BHIE_TXVECSTATUS_OFFS (0x0044)
+#define BHIE_TXVECSTATUS_SEQNUM_BMSK (0x3FFFFFFF)
+#define BHIE_TXVECSTATUS_SEQNUM_SHFT (0)
+#define BHIE_TXVECSTATUS_STATUS_BMSK (0xC0000000)
+#define BHIE_TXVECSTATUS_STATUS_SHFT (30)
+#define BHIE_TXVECSTATUS_STATUS_RESET (0x00)
+#define BHIE_TXVECSTATUS_STATUS_XFER_COMPL (0x02)
+#define BHIE_TXVECSTATUS_STATUS_ERROR (0x03)
+#define BHIE_RXVECADDR_LOW_OFFS (0x0060)
+#define BHIE_RXVECADDR_HIGH_OFFS (0x0064)
+#define BHIE_RXVECSIZE_OFFS (0x0068)
+#define BHIE_RXVECDB_OFFS (0x0070)
+#define BHIE_RXVECDB_SEQNUM_BMSK (0x3FFFFFFF)
+#define BHIE_RXVECDB_SEQNUM_SHFT (0)
+#define BHIE_RXVECSTATUS_OFFS (0x0078)
+#define BHIE_RXVECSTATUS_SEQNUM_BMSK (0x3FFFFFFF)
+#define BHIE_RXVECSTATUS_SEQNUM_SHFT (0)
+#define BHIE_RXVECSTATUS_STATUS_BMSK (0xC0000000)
+#define BHIE_RXVECSTATUS_STATUS_SHFT (30)
+#define BHIE_RXVECSTATUS_STATUS_RESET (0x00)
+#define BHIE_RXVECSTATUS_STATUS_XFER_COMPL (0x02)
+#define BHIE_RXVECSTATUS_STATUS_ERROR (0x03)
+
+#define SOC_HW_VERSION_OFFS (0x224)
+#define SOC_HW_VERSION_FAM_NUM_BMSK (0xF0000000)
+#define SOC_HW_VERSION_FAM_NUM_SHFT (28)
+#define SOC_HW_VERSION_DEV_NUM_BMSK (0x0FFF0000)
+#define SOC_HW_VERSION_DEV_NUM_SHFT (16)
+#define SOC_HW_VERSION_MAJOR_VER_BMSK (0x0000FF00)
+#define SOC_HW_VERSION_MAJOR_VER_SHFT (8)
+#define SOC_HW_VERSION_MINOR_VER_BMSK (0x000000FF)
+#define SOC_HW_VERSION_MINOR_VER_SHFT (0)
+
+#define EV_CTX_RESERVED_MASK GENMASK(7, 0)
+#define EV_CTX_INTMODC_MASK GENMASK(15, 8)
+#define EV_CTX_INTMODC_SHIFT 8
+#define EV_CTX_INTMODT_MASK GENMASK(31, 16)
+#define EV_CTX_INTMODT_SHIFT 16
+struct mhi_event_ctxt {
+	__le32 intmod;
+	__le32 ertype;
+	__le32 msivec;
+
+	__le64 rbase __packed __aligned(4);
+	__le64 rlen __packed __aligned(4);
+	__le64 rp __packed __aligned(4);
+	__le64 wp __packed __aligned(4);
+};
+
+#define CHAN_CTX_CHSTATE_MASK GENMASK(7, 0)
+#define CHAN_CTX_CHSTATE_SHIFT 0
+#define CHAN_CTX_BRSTMODE_MASK GENMASK(9, 8)
+#define CHAN_CTX_BRSTMODE_SHIFT 8
+#define CHAN_CTX_POLLCFG_MASK GENMASK(15, 10)
+#define CHAN_CTX_POLLCFG_SHIFT 10
+#define CHAN_CTX_RESERVED_MASK GENMASK(31, 16)
+struct mhi_chan_ctxt {
+	__le32 chcfg;
+	__le32 chtype;
+	__le32 erindex;
+
+	__le64 rbase __packed __aligned(4);
+	__le64 rlen __packed __aligned(4);
+	__le64 rp __packed __aligned(4);
+	__le64 wp __packed __aligned(4);
+};
+
+struct mhi_cmd_ctxt {
+	__le32 reserved0;
+	__le32 reserved1;
+	__le32 reserved2;
+
+	__le64 rbase __packed __aligned(4);
+	__le64 rlen __packed __aligned(4);
+	__le64 rp __packed __aligned(4);
+	__le64 wp __packed __aligned(4);
+};
+
+struct mhi_ctxt {
+	struct mhi_event_ctxt *er_ctxt;
+	struct mhi_chan_ctxt *chan_ctxt;
+	struct mhi_cmd_ctxt *cmd_ctxt;
+	dma_addr_t er_ctxt_addr;
+	dma_addr_t chan_ctxt_addr;
+	dma_addr_t cmd_ctxt_addr;
+};
+
+struct mhi_ring_element {
+	__le64 ptr;
+	__le32 dword[2];
+};
+
+struct bhi_vec_entry {
+	u64 dma_addr;
+	u64 size;
+};
+
+enum mhi_cmd_type {
+	MHI_CMD_NOP = 1,
+	MHI_CMD_RESET_CHAN = 16,
+	MHI_CMD_STOP_CHAN = 17,
+	MHI_CMD_START_CHAN = 18,
+};
+
+/* No operation command */
+#define MHI_TRE_CMD_NOOP_PTR (0)
+#define MHI_TRE_CMD_NOOP_DWORD0 (0)
+#define MHI_TRE_CMD_NOOP_DWORD1 (cpu_to_le32(MHI_CMD_NOP << 16))
+
+/* Channel reset command */
+#define MHI_TRE_CMD_RESET_PTR (0)
+#define MHI_TRE_CMD_RESET_DWORD0 (0)
+#define MHI_TRE_CMD_RESET_DWORD1(chid) (cpu_to_le32((chid << 24) | \
+					(MHI_CMD_RESET_CHAN << 16)))
+
+/* Channel stop command */
+#define MHI_TRE_CMD_STOP_PTR (0)
+#define MHI_TRE_CMD_STOP_DWORD0 (0)
+#define MHI_TRE_CMD_STOP_DWORD1(chid) (cpu_to_le32((chid << 24) | \
+				       (MHI_CMD_STOP_CHAN << 16)))
+
+/* Channel start command */
+#define MHI_TRE_CMD_START_PTR (0)
+#define MHI_TRE_CMD_START_DWORD0 (0)
+#define MHI_TRE_CMD_START_DWORD1(chid) (cpu_to_le32((chid << 24) | \
+					(MHI_CMD_START_CHAN << 16)))
+
+#define MHI_TRE_GET_DWORD(tre, word) (le32_to_cpu((tre)->dword[(word)]))
+#define MHI_TRE_GET_CMD_CHID(tre) ((MHI_TRE_GET_DWORD(tre, 1) >> 24) & 0xFF)
+#define MHI_TRE_GET_CMD_TYPE(tre) ((MHI_TRE_GET_DWORD(tre, 1) >> 16) & 0xFF)
+
+/* Event descriptor macros */
+#define MHI_TRE_EV_PTR(ptr) (cpu_to_le64(ptr))
+#define MHI_TRE_EV_DWORD0(code, len) (cpu_to_le32((code << 24) | len))
+#define MHI_TRE_EV_DWORD1(chid, type) (cpu_to_le32((chid << 24) | (type << 16)))
+#define MHI_TRE_GET_EV_PTR(tre) (le64_to_cpu((tre)->ptr))
+#define MHI_TRE_GET_EV_CODE(tre) ((MHI_TRE_GET_DWORD(tre, 0) >> 24) & 0xFF)
+#define MHI_TRE_GET_EV_LEN(tre) (MHI_TRE_GET_DWORD(tre, 0) & 0xFFFF)
+#define MHI_TRE_GET_EV_CHID(tre) ((MHI_TRE_GET_DWORD(tre, 1) >> 24) & 0xFF)
+#define MHI_TRE_GET_EV_TYPE(tre) ((MHI_TRE_GET_DWORD(tre, 1) >> 16) & 0xFF)
+#define MHI_TRE_GET_EV_STATE(tre) ((MHI_TRE_GET_DWORD(tre, 0) >> 24) & 0xFF)
+#define MHI_TRE_GET_EV_EXECENV(tre) ((MHI_TRE_GET_DWORD(tre, 0) >> 24) & 0xFF)
+#define MHI_TRE_GET_EV_SEQ(tre) MHI_TRE_GET_DWORD(tre, 0)
+#define MHI_TRE_GET_EV_TIME(tre) (MHI_TRE_GET_EV_PTR(tre))
+#define MHI_TRE_GET_EV_COOKIE(tre) lower_32_bits(MHI_TRE_GET_EV_PTR(tre))
+#define MHI_TRE_GET_EV_VEID(tre) ((MHI_TRE_GET_DWORD(tre, 0) >> 16) & 0xFF)
+#define MHI_TRE_GET_EV_LINKSPEED(tre) ((MHI_TRE_GET_DWORD(tre, 1) >> 24) & 0xFF)
+#define MHI_TRE_GET_EV_LINKWIDTH(tre) (MHI_TRE_GET_DWORD(tre, 0) & 0xFF)
+
+/* Transfer descriptor macros */
+#define MHI_TRE_DATA_PTR(ptr) (cpu_to_le64(ptr))
+#define MHI_TRE_DATA_DWORD0(len) (cpu_to_le32(len & MHI_MAX_MTU))
+#define MHI_TRE_DATA_DWORD1(bei, ieot, ieob, chain) (cpu_to_le32((2 << 16) | (bei << 10) \
+	| (ieot << 9) | (ieob << 8) | chain))
+
+/* RSC transfer descriptor macros */
+#define MHI_RSCTRE_DATA_PTR(ptr, len) (cpu_to_le64(((u64)len << 48) | ptr))
+#define MHI_RSCTRE_DATA_DWORD0(cookie) (cpu_to_le32(cookie))
+#define MHI_RSCTRE_DATA_DWORD1 (cpu_to_le32(MHI_PKT_TYPE_COALESCING << 16))
+
+enum mhi_pkt_type {
+	MHI_PKT_TYPE_INVALID = 0x0,
+	MHI_PKT_TYPE_NOOP_CMD = 0x1,
+	MHI_PKT_TYPE_TRANSFER = 0x2,
+	MHI_PKT_TYPE_COALESCING = 0x8,
+	MHI_PKT_TYPE_RESET_CHAN_CMD = 0x10,
+	MHI_PKT_TYPE_STOP_CHAN_CMD = 0x11,
+	MHI_PKT_TYPE_START_CHAN_CMD = 0x12,
+	MHI_PKT_TYPE_STATE_CHANGE_EVENT = 0x20,
+	MHI_PKT_TYPE_CMD_COMPLETION_EVENT = 0x21,
+	MHI_PKT_TYPE_TX_EVENT = 0x22,
+	MHI_PKT_TYPE_RSC_TX_EVENT = 0x28,
+	MHI_PKT_TYPE_EE_EVENT = 0x40,
+	MHI_PKT_TYPE_TSYNC_EVENT = 0x48,
+	MHI_PKT_TYPE_BW_REQ_EVENT = 0x50,
+	MHI_PKT_TYPE_STALE_EVENT, /* internal event */
+};
+
+/* MHI transfer completion events */
+enum mhi_ev_ccs {
+	MHI_EV_CC_INVALID = 0x0,
+	MHI_EV_CC_SUCCESS = 0x1,
+	MHI_EV_CC_EOT = 0x2, /* End of transfer event */
+	MHI_EV_CC_OVERFLOW = 0x3,
+	MHI_EV_CC_EOB = 0x4, /* End of block event */
+	MHI_EV_CC_OOB = 0x5, /* Out of block event */
+	MHI_EV_CC_DB_MODE = 0x6,
+	MHI_EV_CC_UNDEFINED_ERR = 0x10,
+	MHI_EV_CC_BAD_TRE = 0x11,
+};
+
+enum mhi_ch_state {
+	MHI_CH_STATE_DISABLED = 0x0,
+	MHI_CH_STATE_ENABLED = 0x1,
+	MHI_CH_STATE_RUNNING = 0x2,
+	MHI_CH_STATE_SUSPENDED = 0x3,
+	MHI_CH_STATE_STOP = 0x4,
+	MHI_CH_STATE_ERROR = 0x5,
+};
+
+enum mhi_ch_state_type {
+	MHI_CH_STATE_TYPE_RESET,
+	MHI_CH_STATE_TYPE_STOP,
+	MHI_CH_STATE_TYPE_START,
+	MHI_CH_STATE_TYPE_MAX,
+};
+
+extern const char * const mhi_ch_state_type_str[MHI_CH_STATE_TYPE_MAX];
+#define TO_CH_STATE_TYPE_STR(state) (((state) >= MHI_CH_STATE_TYPE_MAX) ? \
+				     "INVALID_STATE" : \
+				     mhi_ch_state_type_str[(state)])
+
+#define MHI_INVALID_BRSTMODE(mode) (mode != MHI_DB_BRST_DISABLE && \
+				    mode != MHI_DB_BRST_ENABLE)
+
+extern const char * const mhi_ee_str[MHI_EE_MAX];
+#define TO_MHI_EXEC_STR(ee) (((ee) >= MHI_EE_MAX) ? \
+			     "INVALID_EE" : mhi_ee_str[ee])
+
+#define MHI_IN_PBL(ee) (ee == MHI_EE_PBL || ee == MHI_EE_PTHRU || \
+			ee == MHI_EE_EDL)
+
+#define MHI_IN_MISSION_MODE(ee) (ee == MHI_EE_AMSS || ee == MHI_EE_WFW || \
+				 ee == MHI_EE_FP)
+
+enum dev_st_transition {
+	DEV_ST_TRANSITION_PBL,
+	DEV_ST_TRANSITION_READY,
+	DEV_ST_TRANSITION_SBL,
+	DEV_ST_TRANSITION_MISSION_MODE,
+	DEV_ST_TRANSITION_FP,
+	DEV_ST_TRANSITION_SYS_ERR,
+	DEV_ST_TRANSITION_DISABLE,
+	DEV_ST_TRANSITION_MAX,
+};
+
+extern const char * const dev_state_tran_str[DEV_ST_TRANSITION_MAX];
+#define TO_DEV_STATE_TRANS_STR(state) (((state) >= DEV_ST_TRANSITION_MAX) ? \
+				"INVALID_STATE" : dev_state_tran_str[state])
+
+extern const char * const mhi_state_str[MHI_STATE_MAX];
+#define TO_MHI_STATE_STR(state) ((state >= MHI_STATE_MAX || \
+				  !mhi_state_str[state]) ? \
+				"INVALID_STATE" : mhi_state_str[state])
+
+/* internal power states */
+enum mhi_pm_state {
+	MHI_PM_STATE_DISABLE,
+	MHI_PM_STATE_POR,
+	MHI_PM_STATE_M0,
+	MHI_PM_STATE_M2,
+	MHI_PM_STATE_M3_ENTER,
+	MHI_PM_STATE_M3,
+	MHI_PM_STATE_M3_EXIT,
+	MHI_PM_STATE_FW_DL_ERR,
+	MHI_PM_STATE_SYS_ERR_DETECT,
+	MHI_PM_STATE_SYS_ERR_PROCESS,
+	MHI_PM_STATE_SHUTDOWN_PROCESS,
+	MHI_PM_STATE_LD_ERR_FATAL_DETECT,
+	MHI_PM_STATE_MAX
+};
+
+#define MHI_PM_DISABLE			BIT(0)
+#define MHI_PM_POR			BIT(1)
+#define MHI_PM_M0			BIT(2)
+#define MHI_PM_M2			BIT(3)
+#define MHI_PM_M3_ENTER			BIT(4)
+#define MHI_PM_M3			BIT(5)
+#define MHI_PM_M3_EXIT			BIT(6)
+/* firmware download failure state */
+#define MHI_PM_FW_DL_ERR		BIT(7)
+#define MHI_PM_SYS_ERR_DETECT		BIT(8)
+#define MHI_PM_SYS_ERR_PROCESS		BIT(9)
+#define MHI_PM_SHUTDOWN_PROCESS		BIT(10)
+/* link not accessible */
+#define MHI_PM_LD_ERR_FATAL_DETECT	BIT(11)
+
+#define MHI_REG_ACCESS_VALID(pm_state) ((pm_state & (MHI_PM_POR | MHI_PM_M0 | \
+		MHI_PM_M2 | MHI_PM_M3_ENTER | MHI_PM_M3_EXIT | \
+		MHI_PM_SYS_ERR_DETECT | MHI_PM_SYS_ERR_PROCESS | \
+		MHI_PM_SHUTDOWN_PROCESS | MHI_PM_FW_DL_ERR)))
+#define MHI_PM_IN_ERROR_STATE(pm_state) (pm_state >= MHI_PM_FW_DL_ERR)
+#define MHI_PM_IN_FATAL_STATE(pm_state) (pm_state == MHI_PM_LD_ERR_FATAL_DETECT)
+#define MHI_DB_ACCESS_VALID(mhi_cntrl) (mhi_cntrl->pm_state & \
+					mhi_cntrl->db_access)
+#define MHI_WAKE_DB_CLEAR_VALID(pm_state) (pm_state & (MHI_PM_M0 | \
+						MHI_PM_M2 | MHI_PM_M3_EXIT))
+#define MHI_WAKE_DB_SET_VALID(pm_state) (pm_state & MHI_PM_M2)
+#define MHI_WAKE_DB_FORCE_SET_VALID(pm_state) MHI_WAKE_DB_CLEAR_VALID(pm_state)
+#define MHI_EVENT_ACCESS_INVALID(pm_state) (pm_state == MHI_PM_DISABLE || \
+					    MHI_PM_IN_ERROR_STATE(pm_state))
+#define MHI_PM_IN_SUSPEND_STATE(pm_state) (pm_state & \
+					   (MHI_PM_M3_ENTER | MHI_PM_M3))
+
+#define NR_OF_CMD_RINGS			1
+#define CMD_EL_PER_RING			128
+#define PRIMARY_CMD_RING		0
+#define MHI_DEV_WAKE_DB			127
+#define MHI_MAX_MTU			0xffff
+#define MHI_RANDOM_U32_NONZERO(bmsk)	(prandom_u32_max(bmsk) + 1)
+
+enum mhi_er_type {
+	MHI_ER_TYPE_INVALID = 0x0,
+	MHI_ER_TYPE_VALID = 0x1,
+};
+
+struct db_cfg {
+	bool reset_req;
+	bool db_mode;
+	u32 pollcfg;
+	enum mhi_db_brst_mode brstmode;
+	dma_addr_t db_val;
+	void (*process_db)(struct mhi_controller *mhi_cntrl,
+			   struct db_cfg *db_cfg, void __iomem *io_addr,
+			   dma_addr_t db_val);
+};
+
+struct mhi_pm_transitions {
+	enum mhi_pm_state from_state;
+	u32 to_states;
+};
+
+struct state_transition {
+	struct list_head node;
+	enum dev_st_transition state;
+};
+
+struct mhi_ring {
+	dma_addr_t dma_handle;
+	dma_addr_t iommu_base;
+	__le64 *ctxt_wp; /* point to ctxt wp */
+	void *pre_aligned;
+	void *base;
+	void *rp;
+	void *wp;
+	size_t el_size;
+	size_t len;
+	size_t elements;
+	size_t alloc_size;
+	void __iomem *db_addr;
+};
+
+struct mhi_cmd {
+	struct mhi_ring ring;
+	spinlock_t lock;
+};
+
+struct mhi_buf_info {
+	void *v_addr;
+	void *bb_addr;
+	void *wp;
+	void *cb_buf;
+	dma_addr_t p_addr;
+	size_t len;
+	enum dma_data_direction dir;
+	bool used; /* Indicates whether the buffer is used or not */
+	bool pre_mapped; /* Already pre-mapped by client */
+};
+
+struct mhi_event {
+	struct mhi_controller *mhi_cntrl;
+	struct mhi_chan *mhi_chan; /* dedicated to channel */
+	u32 er_index;
+	u32 intmod;
+	u32 irq;
+	int chan; /* this event ring is dedicated to a channel (optional) */
+	u32 priority;
+	enum mhi_er_data_type data_type;
+	struct mhi_ring ring;
+	struct db_cfg db_cfg;
+	struct tasklet_struct task;
+	spinlock_t lock;
+	int (*process_event)(struct mhi_controller *mhi_cntrl,
+			     struct mhi_event *mhi_event,
+			     u32 event_quota);
+	bool hw_ring;
+	bool cl_manage;
+	bool offload_ev; /* managed by a device driver */
+};
+
+struct mhi_chan {
+	const char *name;
+	/*
+	 * Important: When consuming, increment tre_ring first and when
+	 * releasing, decrement buf_ring first. If tre_ring has space, buf_ring
+	 * is guranteed to have space so we do not need to check both rings.
+	 */
+	struct mhi_ring buf_ring;
+	struct mhi_ring tre_ring;
+	u32 chan;
+	u32 er_index;
+	u32 intmod;
+	enum mhi_ch_type type;
+	enum dma_data_direction dir;
+	struct db_cfg db_cfg;
+	enum mhi_ch_ee_mask ee_mask;
+	enum mhi_ch_state ch_state;
+	enum mhi_ev_ccs ccs;
+	struct mhi_device *mhi_dev;
+	void (*xfer_cb)(struct mhi_device *mhi_dev, struct mhi_result *result);
+	struct mutex mutex;
+	struct completion completion;
+	rwlock_t lock;
+	struct list_head node;
+	bool lpm_notify;
+	bool configured;
+	bool offload_ch;
+	bool pre_alloc;
+	bool wake_capable;
+};
+
+/* Default MHI timeout */
+#define MHI_TIMEOUT_MS (1000)
+
+/* debugfs related functions */
+#ifdef CONFIG_MHI_BUS_DEBUG
+void mhi_create_debugfs(struct mhi_controller *mhi_cntrl);
+void mhi_destroy_debugfs(struct mhi_controller *mhi_cntrl);
+void mhi_debugfs_init(void);
+void mhi_debugfs_exit(void);
+#else
+static inline void mhi_create_debugfs(struct mhi_controller *mhi_cntrl)
+{
+}
+
+static inline void mhi_destroy_debugfs(struct mhi_controller *mhi_cntrl)
+{
+}
+
+static inline void mhi_debugfs_init(void)
+{
+}
+
+static inline void mhi_debugfs_exit(void)
+{
+}
+#endif
+
+struct mhi_device *mhi_alloc_device(struct mhi_controller *mhi_cntrl);
+
+int mhi_destroy_device(struct device *dev, void *data);
+void mhi_create_devices(struct mhi_controller *mhi_cntrl);
+
+int mhi_alloc_bhie_table(struct mhi_controller *mhi_cntrl,
+			 struct image_info **image_info, size_t alloc_size);
+void mhi_free_bhie_table(struct mhi_controller *mhi_cntrl,
+			 struct image_info *image_info);
+
+/* Power management APIs */
+enum mhi_pm_state __must_check mhi_tryset_pm_state(
+					struct mhi_controller *mhi_cntrl,
+					enum mhi_pm_state state);
+const char *to_mhi_pm_state_str(u32 state);
+int mhi_queue_state_transition(struct mhi_controller *mhi_cntrl,
+			       enum dev_st_transition state);
+void mhi_pm_st_worker(struct work_struct *work);
+void mhi_pm_sys_err_handler(struct mhi_controller *mhi_cntrl);
+int mhi_ready_state_transition(struct mhi_controller *mhi_cntrl);
+int mhi_pm_m0_transition(struct mhi_controller *mhi_cntrl);
+void mhi_pm_m1_transition(struct mhi_controller *mhi_cntrl);
+int mhi_pm_m3_transition(struct mhi_controller *mhi_cntrl);
+int __mhi_device_get_sync(struct mhi_controller *mhi_cntrl);
+int mhi_send_cmd(struct mhi_controller *mhi_cntrl, struct mhi_chan *mhi_chan,
+		 enum mhi_cmd_type cmd);
+int mhi_download_amss_image(struct mhi_controller *mhi_cntrl);
+static inline bool mhi_is_active(struct mhi_controller *mhi_cntrl)
+{
+	return (mhi_cntrl->dev_state >= MHI_STATE_M0 &&
+		mhi_cntrl->dev_state <= MHI_STATE_M3_FAST);
+}
+
+static inline void mhi_trigger_resume(struct mhi_controller *mhi_cntrl)
+{
+	pm_wakeup_event(&mhi_cntrl->mhi_dev->dev, 0);
+	mhi_cntrl->runtime_get(mhi_cntrl);
+	mhi_cntrl->runtime_put(mhi_cntrl);
+}
+
+/* Register access methods */
+void mhi_db_brstmode(struct mhi_controller *mhi_cntrl, struct db_cfg *db_cfg,
+		     void __iomem *db_addr, dma_addr_t db_val);
+void mhi_db_brstmode_disable(struct mhi_controller *mhi_cntrl,
+			     struct db_cfg *db_mode, void __iomem *db_addr,
+			     dma_addr_t db_val);
+int __must_check mhi_read_reg(struct mhi_controller *mhi_cntrl,
+			      void __iomem *base, u32 offset, u32 *out);
+int __must_check mhi_read_reg_field(struct mhi_controller *mhi_cntrl,
+				    void __iomem *base, u32 offset, u32 mask,
+				    u32 shift, u32 *out);
+int __must_check mhi_poll_reg_field(struct mhi_controller *mhi_cntrl,
+				    void __iomem *base, u32 offset, u32 mask,
+				    u32 shift, u32 val, u32 delayus);
+void mhi_write_reg(struct mhi_controller *mhi_cntrl, void __iomem *base,
+		   u32 offset, u32 val);
+void mhi_write_reg_field(struct mhi_controller *mhi_cntrl, void __iomem *base,
+			 u32 offset, u32 mask, u32 shift, u32 val);
+void mhi_ring_er_db(struct mhi_event *mhi_event);
+void mhi_write_db(struct mhi_controller *mhi_cntrl, void __iomem *db_addr,
+		  dma_addr_t db_val);
+void mhi_ring_cmd_db(struct mhi_controller *mhi_cntrl, struct mhi_cmd *mhi_cmd);
+void mhi_ring_chan_db(struct mhi_controller *mhi_cntrl,
+		      struct mhi_chan *mhi_chan);
+
+/* Initialization methods */
+int mhi_init_mmio(struct mhi_controller *mhi_cntrl);
+int mhi_init_dev_ctxt(struct mhi_controller *mhi_cntrl);
+void mhi_deinit_dev_ctxt(struct mhi_controller *mhi_cntrl);
+int mhi_init_irq_setup(struct mhi_controller *mhi_cntrl);
+void mhi_deinit_free_irq(struct mhi_controller *mhi_cntrl);
+void mhi_rddm_prepare(struct mhi_controller *mhi_cntrl,
+		      struct image_info *img_info);
+void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl);
+int mhi_prepare_channel(struct mhi_controller *mhi_cntrl,
+			struct mhi_chan *mhi_chan);
+int mhi_init_chan_ctxt(struct mhi_controller *mhi_cntrl,
+		       struct mhi_chan *mhi_chan);
+void mhi_deinit_chan_ctxt(struct mhi_controller *mhi_cntrl,
+			  struct mhi_chan *mhi_chan);
+void mhi_reset_chan(struct mhi_controller *mhi_cntrl,
+		    struct mhi_chan *mhi_chan);
+
+/* Event processing methods */
+void mhi_ctrl_ev_task(unsigned long data);
+void mhi_ev_task(unsigned long data);
+int mhi_process_data_event_ring(struct mhi_controller *mhi_cntrl,
+				struct mhi_event *mhi_event, u32 event_quota);
+int mhi_process_ctrl_ev_ring(struct mhi_controller *mhi_cntrl,
+			     struct mhi_event *mhi_event, u32 event_quota);
+
+/* ISR handlers */
+irqreturn_t mhi_irq_handler(int irq_number, void *dev);
+irqreturn_t mhi_intvec_threaded_handler(int irq_number, void *dev);
+irqreturn_t mhi_intvec_handler(int irq_number, void *dev);
+
+int mhi_gen_tre(struct mhi_controller *mhi_cntrl, struct mhi_chan *mhi_chan,
+		struct mhi_buf_info *info, enum mhi_flags flags);
+int mhi_map_single_no_bb(struct mhi_controller *mhi_cntrl,
+			 struct mhi_buf_info *buf_info);
+int mhi_map_single_use_bb(struct mhi_controller *mhi_cntrl,
+			  struct mhi_buf_info *buf_info);
+void mhi_unmap_single_no_bb(struct mhi_controller *mhi_cntrl,
+			    struct mhi_buf_info *buf_info);
+void mhi_unmap_single_use_bb(struct mhi_controller *mhi_cntrl,
+			     struct mhi_buf_info *buf_info);
+
+#endif /* _MHI_INT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/main.c
@@ -0,0 +1,1682 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-direction.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/mhi.h>
+#include <linux/module.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
+#include "internal.h"
+
+int __must_check mhi_read_reg(struct mhi_controller *mhi_cntrl,
+			      void __iomem *base, u32 offset, u32 *out)
+{
+	return mhi_cntrl->read_reg(mhi_cntrl, base + offset, out);
+}
+
+int __must_check mhi_read_reg_field(struct mhi_controller *mhi_cntrl,
+				    void __iomem *base, u32 offset,
+				    u32 mask, u32 shift, u32 *out)
+{
+	u32 tmp;
+	int ret;
+
+	ret = mhi_read_reg(mhi_cntrl, base, offset, &tmp);
+	if (ret)
+		return ret;
+
+	*out = (tmp & mask) >> shift;
+
+	return 0;
+}
+
+int __must_check mhi_poll_reg_field(struct mhi_controller *mhi_cntrl,
+				    void __iomem *base, u32 offset,
+				    u32 mask, u32 shift, u32 val, u32 delayus)
+{
+	int ret;
+	u32 out, retry = (mhi_cntrl->timeout_ms * 1000) / delayus;
+
+	while (retry--) {
+		ret = mhi_read_reg_field(mhi_cntrl, base, offset, mask, shift,
+					 &out);
+		if (ret)
+			return ret;
+
+		if (out == val)
+			return 0;
+
+		fsleep(delayus);
+	}
+
+	return -ETIMEDOUT;
+}
+
+void mhi_write_reg(struct mhi_controller *mhi_cntrl, void __iomem *base,
+		   u32 offset, u32 val)
+{
+	mhi_cntrl->write_reg(mhi_cntrl, base + offset, val);
+}
+
+void mhi_write_reg_field(struct mhi_controller *mhi_cntrl, void __iomem *base,
+			 u32 offset, u32 mask, u32 shift, u32 val)
+{
+	int ret;
+	u32 tmp;
+
+	ret = mhi_read_reg(mhi_cntrl, base, offset, &tmp);
+	if (ret)
+		return;
+
+	tmp &= ~mask;
+	tmp |= (val << shift);
+	mhi_write_reg(mhi_cntrl, base, offset, tmp);
+}
+
+void mhi_write_db(struct mhi_controller *mhi_cntrl, void __iomem *db_addr,
+		  dma_addr_t db_val)
+{
+	mhi_write_reg(mhi_cntrl, db_addr, 4, upper_32_bits(db_val));
+	mhi_write_reg(mhi_cntrl, db_addr, 0, lower_32_bits(db_val));
+}
+
+void mhi_db_brstmode(struct mhi_controller *mhi_cntrl,
+		     struct db_cfg *db_cfg,
+		     void __iomem *db_addr,
+		     dma_addr_t db_val)
+{
+	if (db_cfg->db_mode) {
+		db_cfg->db_val = db_val;
+		mhi_write_db(mhi_cntrl, db_addr, db_val);
+		db_cfg->db_mode = 0;
+	}
+}
+
+void mhi_db_brstmode_disable(struct mhi_controller *mhi_cntrl,
+			     struct db_cfg *db_cfg,
+			     void __iomem *db_addr,
+			     dma_addr_t db_val)
+{
+	db_cfg->db_val = db_val;
+	mhi_write_db(mhi_cntrl, db_addr, db_val);
+}
+
+void mhi_ring_er_db(struct mhi_event *mhi_event)
+{
+	struct mhi_ring *ring = &mhi_event->ring;
+
+	mhi_event->db_cfg.process_db(mhi_event->mhi_cntrl, &mhi_event->db_cfg,
+				     ring->db_addr, le64_to_cpu(*ring->ctxt_wp));
+}
+
+void mhi_ring_cmd_db(struct mhi_controller *mhi_cntrl, struct mhi_cmd *mhi_cmd)
+{
+	dma_addr_t db;
+	struct mhi_ring *ring = &mhi_cmd->ring;
+
+	db = ring->iommu_base + (ring->wp - ring->base);
+	*ring->ctxt_wp = cpu_to_le64(db);
+	mhi_write_db(mhi_cntrl, ring->db_addr, db);
+}
+
+void mhi_ring_chan_db(struct mhi_controller *mhi_cntrl,
+		      struct mhi_chan *mhi_chan)
+{
+	struct mhi_ring *ring = &mhi_chan->tre_ring;
+	dma_addr_t db;
+
+	db = ring->iommu_base + (ring->wp - ring->base);
+
+	/*
+	 * Writes to the new ring element must be visible to the hardware
+	 * before letting h/w know there is new element to fetch.
+	 */
+	dma_wmb();
+	*ring->ctxt_wp = cpu_to_le64(db);
+
+	mhi_chan->db_cfg.process_db(mhi_cntrl, &mhi_chan->db_cfg,
+				    ring->db_addr, db);
+}
+
+enum mhi_ee_type mhi_get_exec_env(struct mhi_controller *mhi_cntrl)
+{
+	u32 exec;
+	int ret = mhi_read_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_EXECENV, &exec);
+
+	return (ret) ? MHI_EE_MAX : exec;
+}
+EXPORT_SYMBOL_GPL(mhi_get_exec_env);
+
+enum mhi_state mhi_get_mhi_state(struct mhi_controller *mhi_cntrl)
+{
+	u32 state;
+	int ret = mhi_read_reg_field(mhi_cntrl, mhi_cntrl->regs, MHISTATUS,
+				     MHISTATUS_MHISTATE_MASK,
+				     MHISTATUS_MHISTATE_SHIFT, &state);
+	return ret ? MHI_STATE_MAX : state;
+}
+EXPORT_SYMBOL_GPL(mhi_get_mhi_state);
+
+void mhi_soc_reset(struct mhi_controller *mhi_cntrl)
+{
+	if (mhi_cntrl->reset) {
+		mhi_cntrl->reset(mhi_cntrl);
+		return;
+	}
+
+	/* Generic MHI SoC reset */
+	mhi_write_reg(mhi_cntrl, mhi_cntrl->regs, MHI_SOC_RESET_REQ_OFFSET,
+		      MHI_SOC_RESET_REQ);
+}
+EXPORT_SYMBOL_GPL(mhi_soc_reset);
+
+int mhi_map_single_no_bb(struct mhi_controller *mhi_cntrl,
+			 struct mhi_buf_info *buf_info)
+{
+	buf_info->p_addr = dma_map_single(mhi_cntrl->cntrl_dev,
+					  buf_info->v_addr, buf_info->len,
+					  buf_info->dir);
+	if (dma_mapping_error(mhi_cntrl->cntrl_dev, buf_info->p_addr))
+		return -ENOMEM;
+
+	return 0;
+}
+
+int mhi_map_single_use_bb(struct mhi_controller *mhi_cntrl,
+			  struct mhi_buf_info *buf_info)
+{
+	void *buf = dma_alloc_coherent(mhi_cntrl->cntrl_dev, buf_info->len,
+				       &buf_info->p_addr, GFP_ATOMIC);
+
+	if (!buf)
+		return -ENOMEM;
+
+	if (buf_info->dir == DMA_TO_DEVICE)
+		memcpy(buf, buf_info->v_addr, buf_info->len);
+
+	buf_info->bb_addr = buf;
+
+	return 0;
+}
+
+void mhi_unmap_single_no_bb(struct mhi_controller *mhi_cntrl,
+			    struct mhi_buf_info *buf_info)
+{
+	dma_unmap_single(mhi_cntrl->cntrl_dev, buf_info->p_addr, buf_info->len,
+			 buf_info->dir);
+}
+
+void mhi_unmap_single_use_bb(struct mhi_controller *mhi_cntrl,
+			     struct mhi_buf_info *buf_info)
+{
+	if (buf_info->dir == DMA_FROM_DEVICE)
+		memcpy(buf_info->v_addr, buf_info->bb_addr, buf_info->len);
+
+	dma_free_coherent(mhi_cntrl->cntrl_dev, buf_info->len,
+			  buf_info->bb_addr, buf_info->p_addr);
+}
+
+static int get_nr_avail_ring_elements(struct mhi_controller *mhi_cntrl,
+				      struct mhi_ring *ring)
+{
+	int nr_el;
+
+	if (ring->wp < ring->rp) {
+		nr_el = ((ring->rp - ring->wp) / ring->el_size) - 1;
+	} else {
+		nr_el = (ring->rp - ring->base) / ring->el_size;
+		nr_el += ((ring->base + ring->len - ring->wp) /
+			  ring->el_size) - 1;
+	}
+
+	return nr_el;
+}
+
+static void *mhi_to_virtual(struct mhi_ring *ring, dma_addr_t addr)
+{
+	return (addr - ring->iommu_base) + ring->base;
+}
+
+static void mhi_add_ring_element(struct mhi_controller *mhi_cntrl,
+				 struct mhi_ring *ring)
+{
+	ring->wp += ring->el_size;
+	if (ring->wp >= (ring->base + ring->len))
+		ring->wp = ring->base;
+	/* smp update */
+	smp_wmb();
+}
+
+static void mhi_del_ring_element(struct mhi_controller *mhi_cntrl,
+				 struct mhi_ring *ring)
+{
+	ring->rp += ring->el_size;
+	if (ring->rp >= (ring->base + ring->len))
+		ring->rp = ring->base;
+	/* smp update */
+	smp_wmb();
+}
+
+static bool is_valid_ring_ptr(struct mhi_ring *ring, dma_addr_t addr)
+{
+	return addr >= ring->iommu_base && addr < ring->iommu_base + ring->len &&
+			!(addr & (sizeof(struct mhi_ring_element) - 1));
+}
+
+int mhi_destroy_device(struct device *dev, void *data)
+{
+	struct mhi_chan *ul_chan, *dl_chan;
+	struct mhi_device *mhi_dev;
+	struct mhi_controller *mhi_cntrl;
+	enum mhi_ee_type ee = MHI_EE_MAX;
+
+	if (dev->bus != &mhi_bus_type)
+		return 0;
+
+	mhi_dev = to_mhi_device(dev);
+	mhi_cntrl = mhi_dev->mhi_cntrl;
+
+	/* Only destroy virtual devices thats attached to bus */
+	if (mhi_dev->dev_type == MHI_DEVICE_CONTROLLER)
+		return 0;
+
+	ul_chan = mhi_dev->ul_chan;
+	dl_chan = mhi_dev->dl_chan;
+
+	/*
+	 * If execution environment is specified, remove only those devices that
+	 * started in them based on ee_mask for the channels as we move on to a
+	 * different execution environment
+	 */
+	if (data)
+		ee = *(enum mhi_ee_type *)data;
+
+	/*
+	 * For the suspend and resume case, this function will get called
+	 * without mhi_unregister_controller(). Hence, we need to drop the
+	 * references to mhi_dev created for ul and dl channels. We can
+	 * be sure that there will be no instances of mhi_dev left after
+	 * this.
+	 */
+	if (ul_chan) {
+		if (ee != MHI_EE_MAX && !(ul_chan->ee_mask & BIT(ee)))
+			return 0;
+
+		put_device(&ul_chan->mhi_dev->dev);
+	}
+
+	if (dl_chan) {
+		if (ee != MHI_EE_MAX && !(dl_chan->ee_mask & BIT(ee)))
+			return 0;
+
+		put_device(&dl_chan->mhi_dev->dev);
+	}
+
+	dev_dbg(&mhi_cntrl->mhi_dev->dev, "destroy device for chan:%s\n",
+		 mhi_dev->name);
+
+	/* Notify the client and remove the device from MHI bus */
+	device_del(dev);
+	put_device(dev);
+
+	return 0;
+}
+
+int mhi_get_free_desc_count(struct mhi_device *mhi_dev,
+				enum dma_data_direction dir)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan = (dir == DMA_TO_DEVICE) ?
+		mhi_dev->ul_chan : mhi_dev->dl_chan;
+	struct mhi_ring *tre_ring = &mhi_chan->tre_ring;
+
+	return get_nr_avail_ring_elements(mhi_cntrl, tre_ring);
+}
+EXPORT_SYMBOL_GPL(mhi_get_free_desc_count);
+
+void mhi_notify(struct mhi_device *mhi_dev, enum mhi_callback cb_reason)
+{
+	struct mhi_driver *mhi_drv;
+
+	if (!mhi_dev->dev.driver)
+		return;
+
+	mhi_drv = to_mhi_driver(mhi_dev->dev.driver);
+
+	if (mhi_drv->status_cb)
+		mhi_drv->status_cb(mhi_dev, cb_reason);
+}
+EXPORT_SYMBOL_GPL(mhi_notify);
+
+/* Bind MHI channels to MHI devices */
+void mhi_create_devices(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_chan *mhi_chan;
+	struct mhi_device *mhi_dev;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	int i, ret;
+
+	mhi_chan = mhi_cntrl->mhi_chan;
+	for (i = 0; i < mhi_cntrl->max_chan; i++, mhi_chan++) {
+		if (!mhi_chan->configured || mhi_chan->mhi_dev ||
+		    !(mhi_chan->ee_mask & BIT(mhi_cntrl->ee)))
+			continue;
+		mhi_dev = mhi_alloc_device(mhi_cntrl);
+		if (IS_ERR(mhi_dev))
+			return;
+
+		mhi_dev->dev_type = MHI_DEVICE_XFER;
+		switch (mhi_chan->dir) {
+		case DMA_TO_DEVICE:
+			mhi_dev->ul_chan = mhi_chan;
+			mhi_dev->ul_chan_id = mhi_chan->chan;
+			break;
+		case DMA_FROM_DEVICE:
+			/* We use dl_chan as offload channels */
+			mhi_dev->dl_chan = mhi_chan;
+			mhi_dev->dl_chan_id = mhi_chan->chan;
+			break;
+		default:
+			dev_err(dev, "Direction not supported\n");
+			put_device(&mhi_dev->dev);
+			return;
+		}
+
+		get_device(&mhi_dev->dev);
+		mhi_chan->mhi_dev = mhi_dev;
+
+		/* Check next channel if it matches */
+		if ((i + 1) < mhi_cntrl->max_chan && mhi_chan[1].configured) {
+			if (!strcmp(mhi_chan[1].name, mhi_chan->name)) {
+				i++;
+				mhi_chan++;
+				if (mhi_chan->dir == DMA_TO_DEVICE) {
+					mhi_dev->ul_chan = mhi_chan;
+					mhi_dev->ul_chan_id = mhi_chan->chan;
+				} else {
+					mhi_dev->dl_chan = mhi_chan;
+					mhi_dev->dl_chan_id = mhi_chan->chan;
+				}
+				get_device(&mhi_dev->dev);
+				mhi_chan->mhi_dev = mhi_dev;
+			}
+		}
+
+		/* Channel name is same for both UL and DL */
+		mhi_dev->name = mhi_chan->name;
+		dev_set_name(&mhi_dev->dev, "%s_%s",
+			     dev_name(&mhi_cntrl->mhi_dev->dev),
+			     mhi_dev->name);
+
+		/* Init wakeup source if available */
+		if (mhi_dev->dl_chan && mhi_dev->dl_chan->wake_capable)
+			device_init_wakeup(&mhi_dev->dev, true);
+
+		ret = device_add(&mhi_dev->dev);
+		if (ret)
+			put_device(&mhi_dev->dev);
+	}
+}
+
+irqreturn_t mhi_irq_handler(int irq_number, void *dev)
+{
+	struct mhi_event *mhi_event = dev;
+	struct mhi_controller *mhi_cntrl = mhi_event->mhi_cntrl;
+	struct mhi_event_ctxt *er_ctxt =
+		&mhi_cntrl->mhi_ctxt->er_ctxt[mhi_event->er_index];
+	struct mhi_ring *ev_ring = &mhi_event->ring;
+	dma_addr_t ptr = le64_to_cpu(er_ctxt->rp);
+	void *dev_rp;
+
+	if (!is_valid_ring_ptr(ev_ring, ptr)) {
+		dev_err(&mhi_cntrl->mhi_dev->dev,
+			"Event ring rp points outside of the event ring\n");
+		return IRQ_HANDLED;
+	}
+
+	dev_rp = mhi_to_virtual(ev_ring, ptr);
+
+	/* Only proceed if event ring has pending events */
+	if (ev_ring->rp == dev_rp)
+		return IRQ_HANDLED;
+
+	/* For client managed event ring, notify pending data */
+	if (mhi_event->cl_manage) {
+		struct mhi_chan *mhi_chan = mhi_event->mhi_chan;
+		struct mhi_device *mhi_dev = mhi_chan->mhi_dev;
+
+		if (mhi_dev)
+			mhi_notify(mhi_dev, MHI_CB_PENDING_DATA);
+	} else {
+		tasklet_schedule(&mhi_event->task);
+	}
+
+	return IRQ_HANDLED;
+}
+
+irqreturn_t mhi_intvec_threaded_handler(int irq_number, void *priv)
+{
+	struct mhi_controller *mhi_cntrl = priv;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_state state;
+	enum mhi_pm_state pm_state = 0;
+	enum mhi_ee_type ee;
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	if (!MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state)) {
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		goto exit_intvec;
+	}
+
+	state = mhi_get_mhi_state(mhi_cntrl);
+	ee = mhi_get_exec_env(mhi_cntrl);
+	dev_dbg(dev, "local ee: %s state: %s device ee: %s state: %s\n",
+		TO_MHI_EXEC_STR(mhi_cntrl->ee),
+		TO_MHI_STATE_STR(mhi_cntrl->dev_state),
+		TO_MHI_EXEC_STR(ee), TO_MHI_STATE_STR(state));
+
+	if (state == MHI_STATE_SYS_ERR) {
+		dev_dbg(dev, "System error detected\n");
+		pm_state = mhi_tryset_pm_state(mhi_cntrl,
+					       MHI_PM_SYS_ERR_DETECT);
+	}
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	if (pm_state != MHI_PM_SYS_ERR_DETECT)
+		goto exit_intvec;
+
+	switch (ee) {
+	case MHI_EE_RDDM:
+		/* proceed if power down is not already in progress */
+		if (mhi_cntrl->rddm_image && mhi_is_active(mhi_cntrl)) {
+			mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_RDDM);
+			mhi_cntrl->ee = ee;
+			wake_up_all(&mhi_cntrl->state_event);
+		}
+		break;
+	case MHI_EE_PBL:
+	case MHI_EE_EDL:
+	case MHI_EE_PTHRU:
+		mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_FATAL_ERROR);
+		mhi_cntrl->ee = ee;
+		wake_up_all(&mhi_cntrl->state_event);
+		mhi_pm_sys_err_handler(mhi_cntrl);
+		break;
+	default:
+		wake_up_all(&mhi_cntrl->state_event);
+		mhi_pm_sys_err_handler(mhi_cntrl);
+		break;
+	}
+
+exit_intvec:
+
+	return IRQ_HANDLED;
+}
+
+irqreturn_t mhi_intvec_handler(int irq_number, void *dev)
+{
+	struct mhi_controller *mhi_cntrl = dev;
+
+	/* Wake up events waiting for state change */
+	wake_up_all(&mhi_cntrl->state_event);
+
+	return IRQ_WAKE_THREAD;
+}
+
+static void mhi_recycle_ev_ring_element(struct mhi_controller *mhi_cntrl,
+					struct mhi_ring *ring)
+{
+	dma_addr_t ctxt_wp;
+
+	/* Update the WP */
+	ring->wp += ring->el_size;
+	ctxt_wp = le64_to_cpu(*ring->ctxt_wp) + ring->el_size;
+
+	if (ring->wp >= (ring->base + ring->len)) {
+		ring->wp = ring->base;
+		ctxt_wp = ring->iommu_base;
+	}
+
+	*ring->ctxt_wp = cpu_to_le64(ctxt_wp);
+
+	/* Update the RP */
+	ring->rp += ring->el_size;
+	if (ring->rp >= (ring->base + ring->len))
+		ring->rp = ring->base;
+
+	/* Update to all cores */
+	smp_wmb();
+}
+
+static int parse_xfer_event(struct mhi_controller *mhi_cntrl,
+			    struct mhi_ring_element *event,
+			    struct mhi_chan *mhi_chan)
+{
+	struct mhi_ring *buf_ring, *tre_ring;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	struct mhi_result result;
+	unsigned long flags = 0;
+	u32 ev_code;
+
+	ev_code = MHI_TRE_GET_EV_CODE(event);
+	buf_ring = &mhi_chan->buf_ring;
+	tre_ring = &mhi_chan->tre_ring;
+
+	result.transaction_status = (ev_code == MHI_EV_CC_OVERFLOW) ?
+		-EOVERFLOW : 0;
+
+	/*
+	 * If it's a DB Event then we need to grab the lock
+	 * with preemption disabled and as a write because we
+	 * have to update db register and there are chances that
+	 * another thread could be doing the same.
+	 */
+	if (ev_code >= MHI_EV_CC_OOB)
+		write_lock_irqsave(&mhi_chan->lock, flags);
+	else
+		read_lock_bh(&mhi_chan->lock);
+
+	if (mhi_chan->ch_state != MHI_CH_STATE_ENABLED)
+		goto end_process_tx_event;
+
+	switch (ev_code) {
+	case MHI_EV_CC_OVERFLOW:
+	case MHI_EV_CC_EOB:
+	case MHI_EV_CC_EOT:
+	{
+		dma_addr_t ptr = MHI_TRE_GET_EV_PTR(event);
+		struct mhi_ring_element *local_rp, *ev_tre;
+		void *dev_rp;
+		struct mhi_buf_info *buf_info;
+		u16 xfer_len;
+
+		if (!is_valid_ring_ptr(tre_ring, ptr)) {
+			dev_err(&mhi_cntrl->mhi_dev->dev,
+				"Event element points outside of the tre ring\n");
+			break;
+		}
+		/* Get the TRB this event points to */
+		ev_tre = mhi_to_virtual(tre_ring, ptr);
+
+		dev_rp = ev_tre + 1;
+		if (dev_rp >= (tre_ring->base + tre_ring->len))
+			dev_rp = tre_ring->base;
+
+		result.dir = mhi_chan->dir;
+
+		local_rp = tre_ring->rp;
+		while (local_rp != dev_rp) {
+			buf_info = buf_ring->rp;
+			/* If it's the last TRE, get length from the event */
+			if (local_rp == ev_tre)
+				xfer_len = MHI_TRE_GET_EV_LEN(event);
+			else
+				xfer_len = buf_info->len;
+
+			/* Unmap if it's not pre-mapped by client */
+			if (likely(!buf_info->pre_mapped))
+				mhi_cntrl->unmap_single(mhi_cntrl, buf_info);
+
+			result.buf_addr = buf_info->cb_buf;
+
+			/* truncate to buf len if xfer_len is larger */
+			result.bytes_xferd =
+				min_t(u16, xfer_len, buf_info->len);
+			mhi_del_ring_element(mhi_cntrl, buf_ring);
+			mhi_del_ring_element(mhi_cntrl, tre_ring);
+			local_rp = tre_ring->rp;
+
+			read_unlock_bh(&mhi_chan->lock);
+
+			/* notify client */
+			mhi_chan->xfer_cb(mhi_chan->mhi_dev, &result);
+
+			if (mhi_chan->dir == DMA_TO_DEVICE) {
+				atomic_dec(&mhi_cntrl->pending_pkts);
+				/* Release the reference got from mhi_queue() */
+				mhi_cntrl->runtime_put(mhi_cntrl);
+			}
+
+			/*
+			 * Recycle the buffer if buffer is pre-allocated,
+			 * if there is an error, not much we can do apart
+			 * from dropping the packet
+			 */
+			if (mhi_chan->pre_alloc) {
+				if (mhi_queue_buf(mhi_chan->mhi_dev,
+						  mhi_chan->dir,
+						  buf_info->cb_buf,
+						  buf_info->len, MHI_EOT)) {
+					dev_err(dev,
+						"Error recycling buffer for chan:%d\n",
+						mhi_chan->chan);
+					kfree(buf_info->cb_buf);
+				}
+			}
+
+			read_lock_bh(&mhi_chan->lock);
+		}
+		break;
+	} /* CC_EOT */
+	case MHI_EV_CC_OOB:
+	case MHI_EV_CC_DB_MODE:
+	{
+		unsigned long pm_lock_flags;
+
+		mhi_chan->db_cfg.db_mode = 1;
+		read_lock_irqsave(&mhi_cntrl->pm_lock, pm_lock_flags);
+		if (tre_ring->wp != tre_ring->rp &&
+		    MHI_DB_ACCESS_VALID(mhi_cntrl)) {
+			mhi_ring_chan_db(mhi_cntrl, mhi_chan);
+		}
+		read_unlock_irqrestore(&mhi_cntrl->pm_lock, pm_lock_flags);
+		break;
+	}
+	case MHI_EV_CC_BAD_TRE:
+	default:
+		dev_err(dev, "Unknown event 0x%x\n", ev_code);
+		break;
+	} /* switch(MHI_EV_READ_CODE(EV_TRB_CODE,event)) */
+
+end_process_tx_event:
+	if (ev_code >= MHI_EV_CC_OOB)
+		write_unlock_irqrestore(&mhi_chan->lock, flags);
+	else
+		read_unlock_bh(&mhi_chan->lock);
+
+	return 0;
+}
+
+static int parse_rsc_event(struct mhi_controller *mhi_cntrl,
+			   struct mhi_ring_element *event,
+			   struct mhi_chan *mhi_chan)
+{
+	struct mhi_ring *buf_ring, *tre_ring;
+	struct mhi_buf_info *buf_info;
+	struct mhi_result result;
+	int ev_code;
+	u32 cookie; /* offset to local descriptor */
+	u16 xfer_len;
+
+	buf_ring = &mhi_chan->buf_ring;
+	tre_ring = &mhi_chan->tre_ring;
+
+	ev_code = MHI_TRE_GET_EV_CODE(event);
+	cookie = MHI_TRE_GET_EV_COOKIE(event);
+	xfer_len = MHI_TRE_GET_EV_LEN(event);
+
+	/* Received out of bound cookie */
+	WARN_ON(cookie >= buf_ring->len);
+
+	buf_info = buf_ring->base + cookie;
+
+	result.transaction_status = (ev_code == MHI_EV_CC_OVERFLOW) ?
+		-EOVERFLOW : 0;
+
+	/* truncate to buf len if xfer_len is larger */
+	result.bytes_xferd = min_t(u16, xfer_len, buf_info->len);
+	result.buf_addr = buf_info->cb_buf;
+	result.dir = mhi_chan->dir;
+
+	read_lock_bh(&mhi_chan->lock);
+
+	if (mhi_chan->ch_state != MHI_CH_STATE_ENABLED)
+		goto end_process_rsc_event;
+
+	WARN_ON(!buf_info->used);
+
+	/* notify the client */
+	mhi_chan->xfer_cb(mhi_chan->mhi_dev, &result);
+
+	/*
+	 * Note: We're arbitrarily incrementing RP even though, completion
+	 * packet we processed might not be the same one, reason we can do this
+	 * is because device guaranteed to cache descriptors in order it
+	 * receive, so even though completion event is different we can re-use
+	 * all descriptors in between.
+	 * Example:
+	 * Transfer Ring has descriptors: A, B, C, D
+	 * Last descriptor host queue is D (WP) and first descriptor
+	 * host queue is A (RP).
+	 * The completion event we just serviced is descriptor C.
+	 * Then we can safely queue descriptors to replace A, B, and C
+	 * even though host did not receive any completions.
+	 */
+	mhi_del_ring_element(mhi_cntrl, tre_ring);
+	buf_info->used = false;
+
+end_process_rsc_event:
+	read_unlock_bh(&mhi_chan->lock);
+
+	return 0;
+}
+
+static void mhi_process_cmd_completion(struct mhi_controller *mhi_cntrl,
+				       struct mhi_ring_element *tre)
+{
+	dma_addr_t ptr = MHI_TRE_GET_EV_PTR(tre);
+	struct mhi_cmd *cmd_ring = &mhi_cntrl->mhi_cmd[PRIMARY_CMD_RING];
+	struct mhi_ring *mhi_ring = &cmd_ring->ring;
+	struct mhi_ring_element *cmd_pkt;
+	struct mhi_chan *mhi_chan;
+	u32 chan;
+
+	if (!is_valid_ring_ptr(mhi_ring, ptr)) {
+		dev_err(&mhi_cntrl->mhi_dev->dev,
+			"Event element points outside of the cmd ring\n");
+		return;
+	}
+
+	cmd_pkt = mhi_to_virtual(mhi_ring, ptr);
+
+	chan = MHI_TRE_GET_CMD_CHID(cmd_pkt);
+
+	if (chan < mhi_cntrl->max_chan &&
+	    mhi_cntrl->mhi_chan[chan].configured) {
+		mhi_chan = &mhi_cntrl->mhi_chan[chan];
+		write_lock_bh(&mhi_chan->lock);
+		mhi_chan->ccs = MHI_TRE_GET_EV_CODE(tre);
+		complete(&mhi_chan->completion);
+		write_unlock_bh(&mhi_chan->lock);
+	} else {
+		dev_err(&mhi_cntrl->mhi_dev->dev,
+			"Completion packet for invalid channel ID: %d\n", chan);
+	}
+
+	mhi_del_ring_element(mhi_cntrl, mhi_ring);
+}
+
+int mhi_process_ctrl_ev_ring(struct mhi_controller *mhi_cntrl,
+			     struct mhi_event *mhi_event,
+			     u32 event_quota)
+{
+	struct mhi_ring_element *dev_rp, *local_rp;
+	struct mhi_ring *ev_ring = &mhi_event->ring;
+	struct mhi_event_ctxt *er_ctxt =
+		&mhi_cntrl->mhi_ctxt->er_ctxt[mhi_event->er_index];
+	struct mhi_chan *mhi_chan;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	u32 chan;
+	int count = 0;
+	dma_addr_t ptr = le64_to_cpu(er_ctxt->rp);
+
+	/*
+	 * This is a quick check to avoid unnecessary event processing
+	 * in case MHI is already in error state, but it's still possible
+	 * to transition to error state while processing events
+	 */
+	if (unlikely(MHI_EVENT_ACCESS_INVALID(mhi_cntrl->pm_state)))
+		return -EIO;
+
+	if (!is_valid_ring_ptr(ev_ring, ptr)) {
+		dev_err(&mhi_cntrl->mhi_dev->dev,
+			"Event ring rp points outside of the event ring\n");
+		return -EIO;
+	}
+
+	dev_rp = mhi_to_virtual(ev_ring, ptr);
+	local_rp = ev_ring->rp;
+
+	while (dev_rp != local_rp) {
+		enum mhi_pkt_type type = MHI_TRE_GET_EV_TYPE(local_rp);
+
+		switch (type) {
+		case MHI_PKT_TYPE_BW_REQ_EVENT:
+		{
+			struct mhi_link_info *link_info;
+
+			link_info = &mhi_cntrl->mhi_link_info;
+			write_lock_irq(&mhi_cntrl->pm_lock);
+			link_info->target_link_speed =
+				MHI_TRE_GET_EV_LINKSPEED(local_rp);
+			link_info->target_link_width =
+				MHI_TRE_GET_EV_LINKWIDTH(local_rp);
+			write_unlock_irq(&mhi_cntrl->pm_lock);
+			dev_dbg(dev, "Received BW_REQ event\n");
+			mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_BW_REQ);
+			break;
+		}
+		case MHI_PKT_TYPE_STATE_CHANGE_EVENT:
+		{
+			enum mhi_state new_state;
+
+			new_state = MHI_TRE_GET_EV_STATE(local_rp);
+
+			dev_dbg(dev, "State change event to state: %s\n",
+				TO_MHI_STATE_STR(new_state));
+
+			switch (new_state) {
+			case MHI_STATE_M0:
+				mhi_pm_m0_transition(mhi_cntrl);
+				break;
+			case MHI_STATE_M1:
+				mhi_pm_m1_transition(mhi_cntrl);
+				break;
+			case MHI_STATE_M3:
+				mhi_pm_m3_transition(mhi_cntrl);
+				break;
+			case MHI_STATE_SYS_ERR:
+			{
+				enum mhi_pm_state pm_state;
+
+				dev_dbg(dev, "System error detected\n");
+				write_lock_irq(&mhi_cntrl->pm_lock);
+				pm_state = mhi_tryset_pm_state(mhi_cntrl,
+							MHI_PM_SYS_ERR_DETECT);
+				write_unlock_irq(&mhi_cntrl->pm_lock);
+				if (pm_state == MHI_PM_SYS_ERR_DETECT)
+					mhi_pm_sys_err_handler(mhi_cntrl);
+				break;
+			}
+			default:
+				dev_err(dev, "Invalid state: %s\n",
+					TO_MHI_STATE_STR(new_state));
+			}
+
+			break;
+		}
+		case MHI_PKT_TYPE_CMD_COMPLETION_EVENT:
+			mhi_process_cmd_completion(mhi_cntrl, local_rp);
+			break;
+		case MHI_PKT_TYPE_EE_EVENT:
+		{
+			enum dev_st_transition st = DEV_ST_TRANSITION_MAX;
+			enum mhi_ee_type event = MHI_TRE_GET_EV_EXECENV(local_rp);
+
+			dev_dbg(dev, "Received EE event: %s\n",
+				TO_MHI_EXEC_STR(event));
+			switch (event) {
+			case MHI_EE_SBL:
+				st = DEV_ST_TRANSITION_SBL;
+				break;
+			case MHI_EE_WFW:
+			case MHI_EE_AMSS:
+				st = DEV_ST_TRANSITION_MISSION_MODE;
+				break;
+			case MHI_EE_FP:
+				st = DEV_ST_TRANSITION_FP;
+				break;
+			case MHI_EE_RDDM:
+				mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_RDDM);
+				write_lock_irq(&mhi_cntrl->pm_lock);
+				mhi_cntrl->ee = event;
+				write_unlock_irq(&mhi_cntrl->pm_lock);
+				wake_up_all(&mhi_cntrl->state_event);
+				break;
+			default:
+				dev_err(dev,
+					"Unhandled EE event: 0x%x\n", type);
+			}
+			if (st != DEV_ST_TRANSITION_MAX)
+				mhi_queue_state_transition(mhi_cntrl, st);
+
+			break;
+		}
+		case MHI_PKT_TYPE_TX_EVENT:
+			chan = MHI_TRE_GET_EV_CHID(local_rp);
+
+			WARN_ON(chan >= mhi_cntrl->max_chan);
+
+			/*
+			 * Only process the event ring elements whose channel
+			 * ID is within the maximum supported range.
+			 */
+			if (chan < mhi_cntrl->max_chan) {
+				mhi_chan = &mhi_cntrl->mhi_chan[chan];
+				if (!mhi_chan->configured)
+					break;
+				parse_xfer_event(mhi_cntrl, local_rp, mhi_chan);
+				event_quota--;
+			}
+			break;
+		default:
+			dev_err(dev, "Unhandled event type: %d\n", type);
+			break;
+		}
+
+		mhi_recycle_ev_ring_element(mhi_cntrl, ev_ring);
+		local_rp = ev_ring->rp;
+
+		ptr = le64_to_cpu(er_ctxt->rp);
+		if (!is_valid_ring_ptr(ev_ring, ptr)) {
+			dev_err(&mhi_cntrl->mhi_dev->dev,
+				"Event ring rp points outside of the event ring\n");
+			return -EIO;
+		}
+
+		dev_rp = mhi_to_virtual(ev_ring, ptr);
+		count++;
+	}
+
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (likely(MHI_DB_ACCESS_VALID(mhi_cntrl)))
+		mhi_ring_er_db(mhi_event);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	return count;
+}
+
+int mhi_process_data_event_ring(struct mhi_controller *mhi_cntrl,
+				struct mhi_event *mhi_event,
+				u32 event_quota)
+{
+	struct mhi_ring_element *dev_rp, *local_rp;
+	struct mhi_ring *ev_ring = &mhi_event->ring;
+	struct mhi_event_ctxt *er_ctxt =
+		&mhi_cntrl->mhi_ctxt->er_ctxt[mhi_event->er_index];
+	int count = 0;
+	u32 chan;
+	struct mhi_chan *mhi_chan;
+	dma_addr_t ptr = le64_to_cpu(er_ctxt->rp);
+
+	if (unlikely(MHI_EVENT_ACCESS_INVALID(mhi_cntrl->pm_state)))
+		return -EIO;
+
+	if (!is_valid_ring_ptr(ev_ring, ptr)) {
+		dev_err(&mhi_cntrl->mhi_dev->dev,
+			"Event ring rp points outside of the event ring\n");
+		return -EIO;
+	}
+
+	dev_rp = mhi_to_virtual(ev_ring, ptr);
+	local_rp = ev_ring->rp;
+
+	while (dev_rp != local_rp && event_quota > 0) {
+		enum mhi_pkt_type type = MHI_TRE_GET_EV_TYPE(local_rp);
+
+		chan = MHI_TRE_GET_EV_CHID(local_rp);
+
+		WARN_ON(chan >= mhi_cntrl->max_chan);
+
+		/*
+		 * Only process the event ring elements whose channel
+		 * ID is within the maximum supported range.
+		 */
+		if (chan < mhi_cntrl->max_chan &&
+		    mhi_cntrl->mhi_chan[chan].configured) {
+			mhi_chan = &mhi_cntrl->mhi_chan[chan];
+
+			if (likely(type == MHI_PKT_TYPE_TX_EVENT)) {
+				parse_xfer_event(mhi_cntrl, local_rp, mhi_chan);
+				event_quota--;
+			} else if (type == MHI_PKT_TYPE_RSC_TX_EVENT) {
+				parse_rsc_event(mhi_cntrl, local_rp, mhi_chan);
+				event_quota--;
+			}
+		}
+
+		mhi_recycle_ev_ring_element(mhi_cntrl, ev_ring);
+		local_rp = ev_ring->rp;
+
+		ptr = le64_to_cpu(er_ctxt->rp);
+		if (!is_valid_ring_ptr(ev_ring, ptr)) {
+			dev_err(&mhi_cntrl->mhi_dev->dev,
+				"Event ring rp points outside of the event ring\n");
+			return -EIO;
+		}
+
+		dev_rp = mhi_to_virtual(ev_ring, ptr);
+		count++;
+	}
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (likely(MHI_DB_ACCESS_VALID(mhi_cntrl)))
+		mhi_ring_er_db(mhi_event);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	return count;
+}
+
+void mhi_ev_task(unsigned long data)
+{
+	struct mhi_event *mhi_event = (struct mhi_event *)data;
+	struct mhi_controller *mhi_cntrl = mhi_event->mhi_cntrl;
+
+	/* process all pending events */
+	spin_lock_bh(&mhi_event->lock);
+	mhi_event->process_event(mhi_cntrl, mhi_event, U32_MAX);
+	spin_unlock_bh(&mhi_event->lock);
+}
+
+void mhi_ctrl_ev_task(unsigned long data)
+{
+	struct mhi_event *mhi_event = (struct mhi_event *)data;
+	struct mhi_controller *mhi_cntrl = mhi_event->mhi_cntrl;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_state state;
+	enum mhi_pm_state pm_state = 0;
+	int ret;
+
+	/*
+	 * We can check PM state w/o a lock here because there is no way
+	 * PM state can change from reg access valid to no access while this
+	 * thread being executed.
+	 */
+	if (!MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state)) {
+		/*
+		 * We may have a pending event but not allowed to
+		 * process it since we are probably in a suspended state,
+		 * so trigger a resume.
+		 */
+		mhi_trigger_resume(mhi_cntrl);
+
+		return;
+	}
+
+	/* Process ctrl events events */
+	ret = mhi_event->process_event(mhi_cntrl, mhi_event, U32_MAX);
+
+	/*
+	 * We received an IRQ but no events to process, maybe device went to
+	 * SYS_ERR state? Check the state to confirm.
+	 */
+	if (!ret) {
+		write_lock_irq(&mhi_cntrl->pm_lock);
+		state = mhi_get_mhi_state(mhi_cntrl);
+		if (state == MHI_STATE_SYS_ERR) {
+			dev_dbg(dev, "System error detected\n");
+			pm_state = mhi_tryset_pm_state(mhi_cntrl,
+						       MHI_PM_SYS_ERR_DETECT);
+		}
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		if (pm_state == MHI_PM_SYS_ERR_DETECT)
+			mhi_pm_sys_err_handler(mhi_cntrl);
+	}
+}
+
+static bool mhi_is_ring_full(struct mhi_controller *mhi_cntrl,
+			     struct mhi_ring *ring)
+{
+	void *tmp = ring->wp + ring->el_size;
+
+	if (tmp >= (ring->base + ring->len))
+		tmp = ring->base;
+
+	return (tmp == ring->rp);
+}
+
+static int mhi_queue(struct mhi_device *mhi_dev, struct mhi_buf_info *buf_info,
+		     enum dma_data_direction dir, enum mhi_flags mflags)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan = (dir == DMA_TO_DEVICE) ? mhi_dev->ul_chan :
+							     mhi_dev->dl_chan;
+	struct mhi_ring *tre_ring = &mhi_chan->tre_ring;
+	unsigned long flags;
+	int ret;
+
+	if (unlikely(MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)))
+		return -EIO;
+
+	ret = mhi_is_ring_full(mhi_cntrl, tre_ring);
+	if (unlikely(ret))
+		return -EAGAIN;
+
+	ret = mhi_gen_tre(mhi_cntrl, mhi_chan, buf_info, mflags);
+	if (unlikely(ret))
+		return ret;
+
+	read_lock_irqsave(&mhi_cntrl->pm_lock, flags);
+
+	/* Packet is queued, take a usage ref to exit M3 if necessary
+	 * for host->device buffer, balanced put is done on buffer completion
+	 * for device->host buffer, balanced put is after ringing the DB
+	 */
+	mhi_cntrl->runtime_get(mhi_cntrl);
+
+	/* Assert dev_wake (to exit/prevent M1/M2)*/
+	mhi_cntrl->wake_toggle(mhi_cntrl);
+
+	if (mhi_chan->dir == DMA_TO_DEVICE)
+		atomic_inc(&mhi_cntrl->pending_pkts);
+
+	if (likely(MHI_DB_ACCESS_VALID(mhi_cntrl)))
+		mhi_ring_chan_db(mhi_cntrl, mhi_chan);
+
+	if (dir == DMA_FROM_DEVICE)
+		mhi_cntrl->runtime_put(mhi_cntrl);
+
+	read_unlock_irqrestore(&mhi_cntrl->pm_lock, flags);
+
+	return ret;
+}
+
+int mhi_queue_skb(struct mhi_device *mhi_dev, enum dma_data_direction dir,
+		  struct sk_buff *skb, size_t len, enum mhi_flags mflags)
+{
+	struct mhi_chan *mhi_chan = (dir == DMA_TO_DEVICE) ? mhi_dev->ul_chan :
+							     mhi_dev->dl_chan;
+	struct mhi_buf_info buf_info = { };
+
+	buf_info.v_addr = skb->data;
+	buf_info.cb_buf = skb;
+	buf_info.len = len;
+
+	if (unlikely(mhi_chan->pre_alloc))
+		return -EINVAL;
+
+	return mhi_queue(mhi_dev, &buf_info, dir, mflags);
+}
+EXPORT_SYMBOL_GPL(mhi_queue_skb);
+
+int mhi_queue_dma(struct mhi_device *mhi_dev, enum dma_data_direction dir,
+		  struct mhi_buf *mhi_buf, size_t len, enum mhi_flags mflags)
+{
+	struct mhi_chan *mhi_chan = (dir == DMA_TO_DEVICE) ? mhi_dev->ul_chan :
+							     mhi_dev->dl_chan;
+	struct mhi_buf_info buf_info = { };
+
+	buf_info.p_addr = mhi_buf->dma_addr;
+	buf_info.cb_buf = mhi_buf;
+	buf_info.pre_mapped = true;
+	buf_info.len = len;
+
+	if (unlikely(mhi_chan->pre_alloc))
+		return -EINVAL;
+
+	return mhi_queue(mhi_dev, &buf_info, dir, mflags);
+}
+EXPORT_SYMBOL_GPL(mhi_queue_dma);
+
+int mhi_gen_tre(struct mhi_controller *mhi_cntrl, struct mhi_chan *mhi_chan,
+			struct mhi_buf_info *info, enum mhi_flags flags)
+{
+	struct mhi_ring *buf_ring, *tre_ring;
+	struct mhi_ring_element *mhi_tre;
+	struct mhi_buf_info *buf_info;
+	int eot, eob, chain, bei;
+	int ret;
+
+	/* Protect accesses for reading and incrementing WP */
+	write_lock_bh(&mhi_chan->lock);
+
+	buf_ring = &mhi_chan->buf_ring;
+	tre_ring = &mhi_chan->tre_ring;
+
+	buf_info = buf_ring->wp;
+	WARN_ON(buf_info->used);
+	buf_info->pre_mapped = info->pre_mapped;
+	if (info->pre_mapped)
+		buf_info->p_addr = info->p_addr;
+	else
+		buf_info->v_addr = info->v_addr;
+	buf_info->cb_buf = info->cb_buf;
+	buf_info->wp = tre_ring->wp;
+	buf_info->dir = mhi_chan->dir;
+	buf_info->len = info->len;
+
+	if (!info->pre_mapped) {
+		ret = mhi_cntrl->map_single(mhi_cntrl, buf_info);
+		if (ret) {
+			write_unlock_bh(&mhi_chan->lock);
+			return ret;
+		}
+	}
+
+	eob = !!(flags & MHI_EOB);
+	eot = !!(flags & MHI_EOT);
+	chain = !!(flags & MHI_CHAIN);
+	bei = !!(mhi_chan->intmod);
+
+	mhi_tre = tre_ring->wp;
+	mhi_tre->ptr = MHI_TRE_DATA_PTR(buf_info->p_addr);
+	mhi_tre->dword[0] = MHI_TRE_DATA_DWORD0(info->len);
+	mhi_tre->dword[1] = MHI_TRE_DATA_DWORD1(bei, eot, eob, chain);
+
+	/* increment WP */
+	mhi_add_ring_element(mhi_cntrl, tre_ring);
+	mhi_add_ring_element(mhi_cntrl, buf_ring);
+
+	write_unlock_bh(&mhi_chan->lock);
+
+	return 0;
+}
+
+int mhi_queue_buf(struct mhi_device *mhi_dev, enum dma_data_direction dir,
+		  void *buf, size_t len, enum mhi_flags mflags)
+{
+	struct mhi_buf_info buf_info = { };
+
+	buf_info.v_addr = buf;
+	buf_info.cb_buf = buf;
+	buf_info.len = len;
+
+	return mhi_queue(mhi_dev, &buf_info, dir, mflags);
+}
+EXPORT_SYMBOL_GPL(mhi_queue_buf);
+
+bool mhi_queue_is_full(struct mhi_device *mhi_dev, enum dma_data_direction dir)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan = (dir == DMA_TO_DEVICE) ?
+					mhi_dev->ul_chan : mhi_dev->dl_chan;
+	struct mhi_ring *tre_ring = &mhi_chan->tre_ring;
+
+	return mhi_is_ring_full(mhi_cntrl, tre_ring);
+}
+EXPORT_SYMBOL_GPL(mhi_queue_is_full);
+
+int mhi_send_cmd(struct mhi_controller *mhi_cntrl,
+		 struct mhi_chan *mhi_chan,
+		 enum mhi_cmd_type cmd)
+{
+	struct mhi_ring_element *cmd_tre = NULL;
+	struct mhi_cmd *mhi_cmd = &mhi_cntrl->mhi_cmd[PRIMARY_CMD_RING];
+	struct mhi_ring *ring = &mhi_cmd->ring;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	int chan = 0;
+
+	if (mhi_chan)
+		chan = mhi_chan->chan;
+
+	spin_lock_bh(&mhi_cmd->lock);
+	if (!get_nr_avail_ring_elements(mhi_cntrl, ring)) {
+		spin_unlock_bh(&mhi_cmd->lock);
+		return -ENOMEM;
+	}
+
+	/* prepare the cmd tre */
+	cmd_tre = ring->wp;
+	switch (cmd) {
+	case MHI_CMD_RESET_CHAN:
+		cmd_tre->ptr = MHI_TRE_CMD_RESET_PTR;
+		cmd_tre->dword[0] = MHI_TRE_CMD_RESET_DWORD0;
+		cmd_tre->dword[1] = MHI_TRE_CMD_RESET_DWORD1(chan);
+		break;
+	case MHI_CMD_STOP_CHAN:
+		cmd_tre->ptr = MHI_TRE_CMD_STOP_PTR;
+		cmd_tre->dword[0] = MHI_TRE_CMD_STOP_DWORD0;
+		cmd_tre->dword[1] = MHI_TRE_CMD_STOP_DWORD1(chan);
+		break;
+	case MHI_CMD_START_CHAN:
+		cmd_tre->ptr = MHI_TRE_CMD_START_PTR;
+		cmd_tre->dword[0] = MHI_TRE_CMD_START_DWORD0;
+		cmd_tre->dword[1] = MHI_TRE_CMD_START_DWORD1(chan);
+		break;
+	default:
+		dev_err(dev, "Command not supported\n");
+		break;
+	}
+
+	/* queue to hardware */
+	mhi_add_ring_element(mhi_cntrl, ring);
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (likely(MHI_DB_ACCESS_VALID(mhi_cntrl)))
+		mhi_ring_cmd_db(mhi_cntrl, mhi_cmd);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+	spin_unlock_bh(&mhi_cmd->lock);
+
+	return 0;
+}
+
+static int mhi_update_channel_state(struct mhi_controller *mhi_cntrl,
+				    struct mhi_chan *mhi_chan,
+				    enum mhi_ch_state_type to_state)
+{
+	struct device *dev = &mhi_chan->mhi_dev->dev;
+	enum mhi_cmd_type cmd = MHI_CMD_NOP;
+	int ret;
+
+	dev_dbg(dev, "%d: Updating channel state to: %s\n", mhi_chan->chan,
+		TO_CH_STATE_TYPE_STR(to_state));
+
+	switch (to_state) {
+	case MHI_CH_STATE_TYPE_RESET:
+		write_lock_irq(&mhi_chan->lock);
+		if (mhi_chan->ch_state != MHI_CH_STATE_STOP &&
+		    mhi_chan->ch_state != MHI_CH_STATE_ENABLED &&
+		    mhi_chan->ch_state != MHI_CH_STATE_SUSPENDED) {
+			write_unlock_irq(&mhi_chan->lock);
+			return -EINVAL;
+		}
+		mhi_chan->ch_state = MHI_CH_STATE_DISABLED;
+		write_unlock_irq(&mhi_chan->lock);
+
+		cmd = MHI_CMD_RESET_CHAN;
+		break;
+	case MHI_CH_STATE_TYPE_STOP:
+		if (mhi_chan->ch_state != MHI_CH_STATE_ENABLED)
+			return -EINVAL;
+
+		cmd = MHI_CMD_STOP_CHAN;
+		break;
+	case MHI_CH_STATE_TYPE_START:
+		if (mhi_chan->ch_state != MHI_CH_STATE_STOP &&
+		    mhi_chan->ch_state != MHI_CH_STATE_DISABLED)
+			return -EINVAL;
+
+		cmd = MHI_CMD_START_CHAN;
+		break;
+	default:
+		dev_err(dev, "%d: Channel state update to %s not allowed\n",
+			mhi_chan->chan, TO_CH_STATE_TYPE_STR(to_state));
+		return -EINVAL;
+	}
+
+	/* bring host and device out of suspended states */
+	ret = mhi_device_get_sync(mhi_cntrl->mhi_dev);
+	if (ret)
+		return ret;
+	mhi_cntrl->runtime_get(mhi_cntrl);
+
+	reinit_completion(&mhi_chan->completion);
+	ret = mhi_send_cmd(mhi_cntrl, mhi_chan, cmd);
+	if (ret) {
+		dev_err(dev, "%d: Failed to send %s channel command\n",
+			mhi_chan->chan, TO_CH_STATE_TYPE_STR(to_state));
+		goto exit_channel_update;
+	}
+
+	ret = wait_for_completion_timeout(&mhi_chan->completion,
+				       msecs_to_jiffies(mhi_cntrl->timeout_ms));
+	if (!ret || mhi_chan->ccs != MHI_EV_CC_SUCCESS) {
+		dev_err(dev,
+			"%d: Failed to receive %s channel command completion\n",
+			mhi_chan->chan, TO_CH_STATE_TYPE_STR(to_state));
+		ret = -EIO;
+		goto exit_channel_update;
+	}
+
+	ret = 0;
+
+	if (to_state != MHI_CH_STATE_TYPE_RESET) {
+		write_lock_irq(&mhi_chan->lock);
+		mhi_chan->ch_state = (to_state == MHI_CH_STATE_TYPE_START) ?
+				      MHI_CH_STATE_ENABLED : MHI_CH_STATE_STOP;
+		write_unlock_irq(&mhi_chan->lock);
+	}
+
+	dev_dbg(dev, "%d: Channel state change to %s successful\n",
+		mhi_chan->chan, TO_CH_STATE_TYPE_STR(to_state));
+
+exit_channel_update:
+	mhi_cntrl->runtime_put(mhi_cntrl);
+	mhi_device_put(mhi_cntrl->mhi_dev);
+
+	return ret;
+}
+
+static void mhi_unprepare_channel(struct mhi_controller *mhi_cntrl,
+				  struct mhi_chan *mhi_chan)
+{
+	int ret;
+	struct device *dev = &mhi_chan->mhi_dev->dev;
+
+	mutex_lock(&mhi_chan->mutex);
+
+	if (!(BIT(mhi_cntrl->ee) & mhi_chan->ee_mask)) {
+		dev_dbg(dev, "Current EE: %s Required EE Mask: 0x%x\n",
+			TO_MHI_EXEC_STR(mhi_cntrl->ee), mhi_chan->ee_mask);
+		goto exit_unprepare_channel;
+	}
+
+	/* no more processing events for this channel */
+	ret = mhi_update_channel_state(mhi_cntrl, mhi_chan,
+				       MHI_CH_STATE_TYPE_RESET);
+	if (ret)
+		dev_err(dev, "%d: Failed to reset channel, still resetting\n",
+			mhi_chan->chan);
+
+exit_unprepare_channel:
+	write_lock_irq(&mhi_chan->lock);
+	mhi_chan->ch_state = MHI_CH_STATE_DISABLED;
+	write_unlock_irq(&mhi_chan->lock);
+
+	if (!mhi_chan->offload_ch) {
+		mhi_reset_chan(mhi_cntrl, mhi_chan);
+		mhi_deinit_chan_ctxt(mhi_cntrl, mhi_chan);
+	}
+	dev_dbg(dev, "%d: successfully reset\n", mhi_chan->chan);
+
+	mutex_unlock(&mhi_chan->mutex);
+}
+
+int mhi_prepare_channel(struct mhi_controller *mhi_cntrl,
+			struct mhi_chan *mhi_chan)
+{
+	int ret = 0;
+	struct device *dev = &mhi_chan->mhi_dev->dev;
+
+	if (!(BIT(mhi_cntrl->ee) & mhi_chan->ee_mask)) {
+		dev_err(dev, "Current EE: %s Required EE Mask: 0x%x\n",
+			TO_MHI_EXEC_STR(mhi_cntrl->ee), mhi_chan->ee_mask);
+		return -ENOTCONN;
+	}
+
+	mutex_lock(&mhi_chan->mutex);
+
+	/* Check of client manages channel context for offload channels */
+	if (!mhi_chan->offload_ch) {
+		ret = mhi_init_chan_ctxt(mhi_cntrl, mhi_chan);
+		if (ret)
+			goto error_init_chan;
+	}
+
+	ret = mhi_update_channel_state(mhi_cntrl, mhi_chan,
+				       MHI_CH_STATE_TYPE_START);
+	if (ret)
+		goto error_pm_state;
+
+	/* Pre-allocate buffer for xfer ring */
+	if (mhi_chan->pre_alloc) {
+		int nr_el = get_nr_avail_ring_elements(mhi_cntrl,
+						       &mhi_chan->tre_ring);
+		size_t len = mhi_cntrl->buffer_len;
+
+		while (nr_el--) {
+			void *buf;
+			struct mhi_buf_info info = { };
+			buf = kmalloc(len, GFP_KERNEL);
+			if (!buf) {
+				ret = -ENOMEM;
+				goto error_pre_alloc;
+			}
+
+			/* Prepare transfer descriptors */
+			info.v_addr = buf;
+			info.cb_buf = buf;
+			info.len = len;
+			ret = mhi_gen_tre(mhi_cntrl, mhi_chan, &info, MHI_EOT);
+			if (ret) {
+				kfree(buf);
+				goto error_pre_alloc;
+			}
+		}
+
+		read_lock_bh(&mhi_cntrl->pm_lock);
+		if (MHI_DB_ACCESS_VALID(mhi_cntrl)) {
+			read_lock_irq(&mhi_chan->lock);
+			mhi_ring_chan_db(mhi_cntrl, mhi_chan);
+			read_unlock_irq(&mhi_chan->lock);
+		}
+		read_unlock_bh(&mhi_cntrl->pm_lock);
+	}
+
+	mutex_unlock(&mhi_chan->mutex);
+
+	return 0;
+
+error_pm_state:
+	if (!mhi_chan->offload_ch)
+		mhi_deinit_chan_ctxt(mhi_cntrl, mhi_chan);
+
+error_init_chan:
+	mutex_unlock(&mhi_chan->mutex);
+
+	return ret;
+
+error_pre_alloc:
+	mutex_unlock(&mhi_chan->mutex);
+	mhi_unprepare_channel(mhi_cntrl, mhi_chan);
+
+	return ret;
+}
+
+static void mhi_mark_stale_events(struct mhi_controller *mhi_cntrl,
+				  struct mhi_event *mhi_event,
+				  struct mhi_event_ctxt *er_ctxt,
+				  int chan)
+
+{
+	struct mhi_ring_element *dev_rp, *local_rp;
+	struct mhi_ring *ev_ring;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	unsigned long flags;
+	dma_addr_t ptr;
+
+	dev_dbg(dev, "Marking all events for chan: %d as stale\n", chan);
+
+	ev_ring = &mhi_event->ring;
+
+	/* mark all stale events related to channel as STALE event */
+	spin_lock_irqsave(&mhi_event->lock, flags);
+
+	ptr = le64_to_cpu(er_ctxt->rp);
+	if (!is_valid_ring_ptr(ev_ring, ptr)) {
+		dev_err(&mhi_cntrl->mhi_dev->dev,
+			"Event ring rp points outside of the event ring\n");
+		dev_rp = ev_ring->rp;
+	} else {
+		dev_rp = mhi_to_virtual(ev_ring, ptr);
+	}
+
+	local_rp = ev_ring->rp;
+	while (dev_rp != local_rp) {
+		if (MHI_TRE_GET_EV_TYPE(local_rp) == MHI_PKT_TYPE_TX_EVENT &&
+		    chan == MHI_TRE_GET_EV_CHID(local_rp))
+			local_rp->dword[1] = MHI_TRE_EV_DWORD1(chan,
+					MHI_PKT_TYPE_STALE_EVENT);
+		local_rp++;
+		if (local_rp == (ev_ring->base + ev_ring->len))
+			local_rp = ev_ring->base;
+	}
+
+	dev_dbg(dev, "Finished marking events as stale events\n");
+	spin_unlock_irqrestore(&mhi_event->lock, flags);
+}
+
+static void mhi_reset_data_chan(struct mhi_controller *mhi_cntrl,
+				struct mhi_chan *mhi_chan)
+{
+	struct mhi_ring *buf_ring, *tre_ring;
+	struct mhi_result result;
+
+	/* Reset any pending buffers */
+	buf_ring = &mhi_chan->buf_ring;
+	tre_ring = &mhi_chan->tre_ring;
+	result.transaction_status = -ENOTCONN;
+	result.bytes_xferd = 0;
+	while (tre_ring->rp != tre_ring->wp) {
+		struct mhi_buf_info *buf_info = buf_ring->rp;
+
+		if (mhi_chan->dir == DMA_TO_DEVICE) {
+			atomic_dec(&mhi_cntrl->pending_pkts);
+			/* Release the reference got from mhi_queue() */
+			mhi_cntrl->runtime_put(mhi_cntrl);
+		}
+
+		if (!buf_info->pre_mapped)
+			mhi_cntrl->unmap_single(mhi_cntrl, buf_info);
+
+		mhi_del_ring_element(mhi_cntrl, buf_ring);
+		mhi_del_ring_element(mhi_cntrl, tre_ring);
+
+		if (mhi_chan->pre_alloc) {
+			kfree(buf_info->cb_buf);
+		} else {
+			result.buf_addr = buf_info->cb_buf;
+			mhi_chan->xfer_cb(mhi_chan->mhi_dev, &result);
+		}
+	}
+}
+
+void mhi_reset_chan(struct mhi_controller *mhi_cntrl, struct mhi_chan *mhi_chan)
+{
+	struct mhi_event *mhi_event;
+	struct mhi_event_ctxt *er_ctxt;
+	int chan = mhi_chan->chan;
+
+	/* Nothing to reset, client doesn't queue buffers */
+	if (mhi_chan->offload_ch)
+		return;
+
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	mhi_event = &mhi_cntrl->mhi_event[mhi_chan->er_index];
+	er_ctxt = &mhi_cntrl->mhi_ctxt->er_ctxt[mhi_chan->er_index];
+
+	mhi_mark_stale_events(mhi_cntrl, mhi_event, er_ctxt, chan);
+
+	mhi_reset_data_chan(mhi_cntrl, mhi_chan);
+
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+}
+
+/* Move channel to start state */
+int mhi_prepare_for_transfer(struct mhi_device *mhi_dev)
+{
+	int ret, dir;
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan;
+
+	for (dir = 0; dir < 2; dir++) {
+		mhi_chan = dir ? mhi_dev->dl_chan : mhi_dev->ul_chan;
+		if (!mhi_chan)
+			continue;
+
+		ret = mhi_prepare_channel(mhi_cntrl, mhi_chan);
+		if (ret)
+			goto error_open_chan;
+	}
+
+	return 0;
+
+error_open_chan:
+	for (--dir; dir >= 0; dir--) {
+		mhi_chan = dir ? mhi_dev->dl_chan : mhi_dev->ul_chan;
+		if (!mhi_chan)
+			continue;
+
+		mhi_unprepare_channel(mhi_cntrl, mhi_chan);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_prepare_for_transfer);
+
+void mhi_unprepare_from_transfer(struct mhi_device *mhi_dev)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan;
+	int dir;
+
+	for (dir = 0; dir < 2; dir++) {
+		mhi_chan = dir ? mhi_dev->ul_chan : mhi_dev->dl_chan;
+		if (!mhi_chan)
+			continue;
+
+		mhi_unprepare_channel(mhi_cntrl, mhi_chan);
+	}
+}
+EXPORT_SYMBOL_GPL(mhi_unprepare_from_transfer);
+
+int mhi_poll(struct mhi_device *mhi_dev, u32 budget)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_chan *mhi_chan = mhi_dev->dl_chan;
+	struct mhi_event *mhi_event = &mhi_cntrl->mhi_event[mhi_chan->er_index];
+	int ret;
+
+	spin_lock_bh(&mhi_event->lock);
+	ret = mhi_event->process_event(mhi_cntrl, mhi_event, budget);
+	spin_unlock_bh(&mhi_event->lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_poll);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/pci_generic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/pci_generic.c
@@ -0,0 +1,1147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MHI PCI driver - MHI over PCI controller driver
+ *
+ * This module is a generic driver for registering MHI-over-PCI devices,
+ * such as PCIe QCOM modems.
+ *
+ * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
+ */
+
+#include <linux/aer.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/mhi.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/pm_runtime.h>
+#include <linux/timer.h>
+#include <linux/workqueue.h>
+
+#define MHI_PCI_DEFAULT_BAR_NUM 0
+
+#define MHI_POST_RESET_DELAY_MS 2000
+
+#define HEALTH_CHECK_PERIOD (HZ * 2)
+
+/**
+ * struct mhi_pci_dev_info - MHI PCI device specific information
+ * @config: MHI controller configuration
+ * @name: name of the PCI module
+ * @fw: firmware path (if any)
+ * @edl: emergency download mode firmware path (if any)
+ * @bar_num: PCI base address register to use for MHI MMIO register space
+ * @dma_data_width: DMA transfer word size (32 or 64 bits)
+ * @mru_default: default MRU size for MBIM network packets
+ * @sideband_wake: Devices using dedicated sideband GPIO for wakeup instead
+ *		   of inband wake support (such as sdx24)
+ */
+struct mhi_pci_dev_info {
+	const struct mhi_controller_config *config;
+	const char *name;
+	const char *fw;
+	const char *edl;
+	unsigned int bar_num;
+	unsigned int dma_data_width;
+	unsigned int mru_default;
+	bool sideband_wake;
+};
+
+#define MHI_CHANNEL_CONFIG_UL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_TO_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+	}						\
+
+#define MHI_CHANNEL_CONFIG_DL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_FROM_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+	}
+
+#define MHI_CHANNEL_CONFIG_DL_AUTOQUEUE(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_FROM_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+		.auto_queue = true,			\
+	}
+
+#define MHI_EVENT_CONFIG_CTRL(ev_ring, el_count) \
+	{					\
+		.num_elements = el_count,	\
+		.irq_moderation_ms = 0,		\
+		.irq = (ev_ring) + 1,		\
+		.priority = 1,			\
+		.mode = MHI_DB_BRST_DISABLE,	\
+		.data_type = MHI_ER_CTRL,	\
+		.hardware_event = false,	\
+		.client_managed = false,	\
+		.offload_channel = false,	\
+	}
+
+#define MHI_CHANNEL_CONFIG_HW_UL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_TO_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_ENABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = true,		\
+	}						\
+
+#define MHI_CHANNEL_CONFIG_HW_DL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_FROM_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_ENABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = true,		\
+	}
+
+#define MHI_CHANNEL_CONFIG_UL_SBL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_TO_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_SBL),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+	}						\
+
+#define MHI_CHANNEL_CONFIG_DL_SBL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_FROM_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_SBL),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+	}
+
+#define MHI_CHANNEL_CONFIG_UL_FP(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_TO_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_FP),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+	}						\
+
+#define MHI_CHANNEL_CONFIG_DL_FP(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_FROM_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_FP),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_DISABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = false,		\
+	}
+
+#define MHI_EVENT_CONFIG_DATA(ev_ring, el_count) \
+	{					\
+		.num_elements = el_count,	\
+		.irq_moderation_ms = 5,		\
+		.irq = (ev_ring) + 1,		\
+		.priority = 1,			\
+		.mode = MHI_DB_BRST_DISABLE,	\
+		.data_type = MHI_ER_DATA,	\
+		.hardware_event = false,	\
+		.client_managed = false,	\
+		.offload_channel = false,	\
+	}
+
+#define MHI_EVENT_CONFIG_HW_DATA(ev_ring, el_count, ch_num) \
+	{					\
+		.num_elements = el_count,	\
+		.irq_moderation_ms = 1,		\
+		.irq = (ev_ring) + 1,		\
+		.priority = 1,			\
+		.mode = MHI_DB_BRST_DISABLE,	\
+		.data_type = MHI_ER_DATA,	\
+		.hardware_event = true,		\
+		.client_managed = false,	\
+		.offload_channel = false,	\
+		.channel = ch_num,		\
+	}
+
+static const struct mhi_channel_config modem_qcom_v1_mhi_channels[] = {
+	MHI_CHANNEL_CONFIG_UL(4, "DIAG", 16, 1),
+	MHI_CHANNEL_CONFIG_DL(5, "DIAG", 16, 1),
+	MHI_CHANNEL_CONFIG_UL(12, "MBIM", 4, 0),
+	MHI_CHANNEL_CONFIG_DL(13, "MBIM", 4, 0),
+	MHI_CHANNEL_CONFIG_UL(14, "QMI", 4, 0),
+	MHI_CHANNEL_CONFIG_DL(15, "QMI", 4, 0),
+	MHI_CHANNEL_CONFIG_UL(20, "IPCR", 8, 0),
+	MHI_CHANNEL_CONFIG_DL_AUTOQUEUE(21, "IPCR", 8, 0),
+	MHI_CHANNEL_CONFIG_UL_FP(34, "FIREHOSE", 32, 0),
+	MHI_CHANNEL_CONFIG_DL_FP(35, "FIREHOSE", 32, 0),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0", 128, 3),
+};
+
+static struct mhi_event_config modem_qcom_v1_mhi_events[] = {
+	/* first ring is control+data ring */
+	MHI_EVENT_CONFIG_CTRL(0, 64),
+	/* DIAG dedicated event ring */
+	MHI_EVENT_CONFIG_DATA(1, 128),
+	/* Hardware channels request dedicated hardware event rings */
+	MHI_EVENT_CONFIG_HW_DATA(2, 1024, 100),
+	MHI_EVENT_CONFIG_HW_DATA(3, 2048, 101)
+};
+
+static const struct mhi_controller_config modem_qcom_v1_mhiv_config = {
+	.max_channels = 128,
+	.timeout_ms = 8000,
+	.num_channels = ARRAY_SIZE(modem_qcom_v1_mhi_channels),
+	.ch_cfg = modem_qcom_v1_mhi_channels,
+	.num_events = ARRAY_SIZE(modem_qcom_v1_mhi_events),
+	.event_cfg = modem_qcom_v1_mhi_events,
+};
+
+static const struct mhi_pci_dev_info mhi_qcom_sdx65_info = {
+	.name = "qcom-sdx65m",
+	.fw = "qcom/sdx65m/xbl.elf",
+	.edl = "qcom/sdx65m/edl.mbn",
+	.config = &modem_qcom_v1_mhiv_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.sideband_wake = false,
+};
+
+static const struct mhi_pci_dev_info mhi_qcom_sdx55_info = {
+	.name = "qcom-sdx55m",
+	.fw = "qcom/sdx55m/sbl1.mbn",
+	.edl = "qcom/sdx55m/edl.mbn",
+	.config = &modem_qcom_v1_mhiv_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.mru_default = 32768,
+	.sideband_wake = false,
+};
+
+static const struct mhi_pci_dev_info mhi_qcom_sdx24_info = {
+	.name = "qcom-sdx24",
+	.edl = "qcom/prog_firehose_sdx24.mbn",
+	.config = &modem_qcom_v1_mhiv_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.sideband_wake = true,
+};
+
+static const struct mhi_channel_config mhi_quectel_em1xx_channels[] = {
+	MHI_CHANNEL_CONFIG_UL(0, "NMEA", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(1, "NMEA", 32, 0),
+	MHI_CHANNEL_CONFIG_UL_SBL(2, "SAHARA", 32, 0),
+	MHI_CHANNEL_CONFIG_DL_SBL(3, "SAHARA", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(4, "DIAG", 32, 1),
+	MHI_CHANNEL_CONFIG_DL(5, "DIAG", 32, 1),
+	MHI_CHANNEL_CONFIG_UL(12, "MBIM", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(13, "MBIM", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(32, "DUN", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(33, "DUN", 32, 0),
+	/* The EDL firmware is a flash-programmer exposing firehose protocol */
+	MHI_CHANNEL_CONFIG_UL_FP(34, "FIREHOSE", 32, 0),
+	MHI_CHANNEL_CONFIG_DL_FP(35, "FIREHOSE", 32, 0),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0_MBIM", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0_MBIM", 128, 3),
+};
+
+static struct mhi_event_config mhi_quectel_em1xx_events[] = {
+	MHI_EVENT_CONFIG_CTRL(0, 128),
+	MHI_EVENT_CONFIG_DATA(1, 128),
+	MHI_EVENT_CONFIG_HW_DATA(2, 1024, 100),
+	MHI_EVENT_CONFIG_HW_DATA(3, 1024, 101)
+};
+
+static const struct mhi_controller_config modem_quectel_em1xx_config = {
+	.max_channels = 128,
+	.timeout_ms = 20000,
+	.num_channels = ARRAY_SIZE(mhi_quectel_em1xx_channels),
+	.ch_cfg = mhi_quectel_em1xx_channels,
+	.num_events = ARRAY_SIZE(mhi_quectel_em1xx_events),
+	.event_cfg = mhi_quectel_em1xx_events,
+};
+
+static const struct mhi_pci_dev_info mhi_quectel_em1xx_info = {
+	.name = "quectel-em1xx",
+	.edl = "qcom/prog_firehose_sdx24.mbn",
+	.config = &modem_quectel_em1xx_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.mru_default = 32768,
+	.sideband_wake = true,
+};
+
+static const struct mhi_channel_config mhi_foxconn_sdx55_channels[] = {
+	MHI_CHANNEL_CONFIG_UL(0, "LOOPBACK", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(1, "LOOPBACK", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(4, "DIAG", 32, 1),
+	MHI_CHANNEL_CONFIG_DL(5, "DIAG", 32, 1),
+	MHI_CHANNEL_CONFIG_UL(12, "MBIM", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(13, "MBIM", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(32, "DUN", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(33, "DUN", 32, 0),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0_MBIM", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0_MBIM", 128, 3),
+};
+
+static struct mhi_event_config mhi_foxconn_sdx55_events[] = {
+	MHI_EVENT_CONFIG_CTRL(0, 128),
+	MHI_EVENT_CONFIG_DATA(1, 128),
+	MHI_EVENT_CONFIG_HW_DATA(2, 1024, 100),
+	MHI_EVENT_CONFIG_HW_DATA(3, 1024, 101)
+};
+
+static const struct mhi_controller_config modem_foxconn_sdx55_config = {
+	.max_channels = 128,
+	.timeout_ms = 20000,
+	.num_channels = ARRAY_SIZE(mhi_foxconn_sdx55_channels),
+	.ch_cfg = mhi_foxconn_sdx55_channels,
+	.num_events = ARRAY_SIZE(mhi_foxconn_sdx55_events),
+	.event_cfg = mhi_foxconn_sdx55_events,
+};
+
+static const struct mhi_pci_dev_info mhi_foxconn_sdx55_info = {
+	.name = "foxconn-sdx55",
+	.fw = "qcom/sdx55m/sbl1.mbn",
+	.edl = "qcom/sdx55m/edl.mbn",
+	.config = &modem_foxconn_sdx55_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.mru_default = 32768,
+	.sideband_wake = false,
+};
+
+static const struct mhi_channel_config mhi_mv31_channels[] = {
+	MHI_CHANNEL_CONFIG_UL(0, "LOOPBACK", 64, 0),
+	MHI_CHANNEL_CONFIG_DL(1, "LOOPBACK", 64, 0),
+	/* MBIM Control Channel */
+	MHI_CHANNEL_CONFIG_UL(12, "MBIM", 64, 0),
+	MHI_CHANNEL_CONFIG_DL(13, "MBIM", 64, 0),
+	/* MBIM Data Channel */
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0_MBIM", 512, 2),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0_MBIM", 512, 3),
+};
+
+static struct mhi_event_config mhi_mv31_events[] = {
+	MHI_EVENT_CONFIG_CTRL(0, 256),
+	MHI_EVENT_CONFIG_DATA(1, 256),
+	MHI_EVENT_CONFIG_HW_DATA(2, 1024, 100),
+	MHI_EVENT_CONFIG_HW_DATA(3, 1024, 101),
+};
+
+static const struct mhi_controller_config modem_mv31_config = {
+	.max_channels = 128,
+	.timeout_ms = 20000,
+	.num_channels = ARRAY_SIZE(mhi_mv31_channels),
+	.ch_cfg = mhi_mv31_channels,
+	.num_events = ARRAY_SIZE(mhi_mv31_events),
+	.event_cfg = mhi_mv31_events,
+};
+
+static const struct mhi_pci_dev_info mhi_mv31_info = {
+	.name = "cinterion-mv31",
+	.config = &modem_mv31_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.mru_default = 32768,
+};
+
+static const struct mhi_channel_config mhi_telit_fn980_hw_v1_channels[] = {
+	MHI_CHANNEL_CONFIG_UL(14, "QMI", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(15, "QMI", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(20, "IPCR", 16, 0),
+	MHI_CHANNEL_CONFIG_DL_AUTOQUEUE(21, "IPCR", 16, 0),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0", 128, 1),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0", 128, 2),
+};
+
+static struct mhi_event_config mhi_telit_fn980_hw_v1_events[] = {
+	MHI_EVENT_CONFIG_CTRL(0, 128),
+	MHI_EVENT_CONFIG_HW_DATA(1, 1024, 100),
+	MHI_EVENT_CONFIG_HW_DATA(2, 2048, 101)
+};
+
+static struct mhi_controller_config modem_telit_fn980_hw_v1_config = {
+	.max_channels = 128,
+	.timeout_ms = 20000,
+	.num_channels = ARRAY_SIZE(mhi_telit_fn980_hw_v1_channels),
+	.ch_cfg = mhi_telit_fn980_hw_v1_channels,
+	.num_events = ARRAY_SIZE(mhi_telit_fn980_hw_v1_events),
+	.event_cfg = mhi_telit_fn980_hw_v1_events,
+};
+
+static const struct mhi_pci_dev_info mhi_telit_fn980_hw_v1_info = {
+	.name = "telit-fn980-hwv1",
+	.fw = "qcom/sdx55m/sbl1.mbn",
+	.edl = "qcom/sdx55m/edl.mbn",
+	.config = &modem_telit_fn980_hw_v1_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.mru_default = 32768,
+	.sideband_wake = false,
+};
+
+static const struct mhi_channel_config mhi_telit_fn990_channels[] = {
+	MHI_CHANNEL_CONFIG_UL_SBL(2, "SAHARA", 32, 0),
+	MHI_CHANNEL_CONFIG_DL_SBL(3, "SAHARA", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(4, "DIAG", 64, 1),
+	MHI_CHANNEL_CONFIG_DL(5, "DIAG", 64, 1),
+	MHI_CHANNEL_CONFIG_UL(12, "MBIM", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(13, "MBIM", 32, 0),
+	MHI_CHANNEL_CONFIG_UL(32, "DUN", 32, 0),
+	MHI_CHANNEL_CONFIG_DL(33, "DUN", 32, 0),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0_MBIM", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0_MBIM", 128, 3),
+};
+
+static struct mhi_event_config mhi_telit_fn990_events[] = {
+	MHI_EVENT_CONFIG_CTRL(0, 128),
+	MHI_EVENT_CONFIG_DATA(1, 128),
+	MHI_EVENT_CONFIG_HW_DATA(2, 1024, 100),
+	MHI_EVENT_CONFIG_HW_DATA(3, 2048, 101)
+};
+
+static const struct mhi_controller_config modem_telit_fn990_config = {
+	.max_channels = 128,
+	.timeout_ms = 20000,
+	.num_channels = ARRAY_SIZE(mhi_telit_fn990_channels),
+	.ch_cfg = mhi_telit_fn990_channels,
+	.num_events = ARRAY_SIZE(mhi_telit_fn990_events),
+	.event_cfg = mhi_telit_fn990_events,
+};
+
+static const struct mhi_pci_dev_info mhi_telit_fn990_info = {
+	.name = "telit-fn990",
+	.config = &modem_telit_fn990_config,
+	.bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+	.dma_data_width = 32,
+	.sideband_wake = false,
+	.mru_default = 32768,
+};
+
+static const struct pci_device_id mhi_pci_id_table[] = {
+	/* Telit FN980 hardware revision v1 */
+	{ PCI_DEVICE_SUB(PCI_VENDOR_ID_QCOM, 0x0306, 0x1C5D, 0x2000),
+		.driver_data = (kernel_ulong_t) &mhi_telit_fn980_hw_v1_info },
+	{ PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x0306),
+		.driver_data = (kernel_ulong_t) &mhi_qcom_sdx55_info },
+	{ PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x0304),
+		.driver_data = (kernel_ulong_t) &mhi_qcom_sdx24_info },
+	/* Telit FN990 */
+	{ PCI_DEVICE_SUB(PCI_VENDOR_ID_QCOM, 0x0308, 0x1c5d, 0x2010),
+		.driver_data = (kernel_ulong_t) &mhi_telit_fn990_info },
+	{ PCI_DEVICE(0x1eac, 0x1001), /* EM120R-GL (sdx24) */
+		.driver_data = (kernel_ulong_t) &mhi_quectel_em1xx_info },
+	{ PCI_DEVICE(0x1eac, 0x1002), /* EM160R-GL (sdx24) */
+		.driver_data = (kernel_ulong_t) &mhi_quectel_em1xx_info },
+	{ PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x0308),
+		.driver_data = (kernel_ulong_t) &mhi_qcom_sdx65_info },
+	/* T99W175 (sdx55), Both for eSIM and Non-eSIM */
+	{ PCI_DEVICE(PCI_VENDOR_ID_FOXCONN, 0xe0ab),
+		.driver_data = (kernel_ulong_t) &mhi_foxconn_sdx55_info },
+	/* DW5930e (sdx55), With eSIM, It's also T99W175 */
+	{ PCI_DEVICE(PCI_VENDOR_ID_FOXCONN, 0xe0b0),
+		.driver_data = (kernel_ulong_t) &mhi_foxconn_sdx55_info },
+	/* DW5930e (sdx55), Non-eSIM, It's also T99W175 */
+	{ PCI_DEVICE(PCI_VENDOR_ID_FOXCONN, 0xe0b1),
+		.driver_data = (kernel_ulong_t) &mhi_foxconn_sdx55_info },
+	/* MV31-W (Cinterion) */
+	{ PCI_DEVICE(0x1269, 0x00b3),
+		.driver_data = (kernel_ulong_t) &mhi_mv31_info },
+	{  }
+};
+MODULE_DEVICE_TABLE(pci, mhi_pci_id_table);
+
+enum mhi_pci_device_status {
+	MHI_PCI_DEV_STARTED,
+	MHI_PCI_DEV_SUSPENDED,
+};
+
+struct mhi_pci_device {
+	struct mhi_controller mhi_cntrl;
+	struct pci_saved_state *pci_state;
+	struct work_struct recovery_work;
+	struct timer_list health_check_timer;
+	unsigned long status;
+};
+
+static int mhi_pci_read_reg(struct mhi_controller *mhi_cntrl,
+			    void __iomem *addr, u32 *out)
+{
+	*out = readl(addr);
+	return 0;
+}
+
+static void mhi_pci_write_reg(struct mhi_controller *mhi_cntrl,
+			      void __iomem *addr, u32 val)
+{
+	writel(val, addr);
+}
+
+static void mhi_pci_status_cb(struct mhi_controller *mhi_cntrl,
+			      enum mhi_callback cb)
+{
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+
+	/* Nothing to do for now */
+	switch (cb) {
+	case MHI_CB_FATAL_ERROR:
+	case MHI_CB_SYS_ERROR:
+		dev_warn(&pdev->dev, "firmware crashed (%u)\n", cb);
+		pm_runtime_forbid(&pdev->dev);
+		break;
+	case MHI_CB_EE_MISSION_MODE:
+		pm_runtime_allow(&pdev->dev);
+		break;
+	default:
+		break;
+	}
+}
+
+static void mhi_pci_wake_get_nop(struct mhi_controller *mhi_cntrl, bool force)
+{
+	/* no-op */
+}
+
+static void mhi_pci_wake_put_nop(struct mhi_controller *mhi_cntrl, bool override)
+{
+	/* no-op */
+}
+
+static void mhi_pci_wake_toggle_nop(struct mhi_controller *mhi_cntrl)
+{
+	/* no-op */
+}
+
+static bool mhi_pci_is_alive(struct mhi_controller *mhi_cntrl)
+{
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	u16 vendor = 0;
+
+	if (pci_read_config_word(pdev, PCI_VENDOR_ID, &vendor))
+		return false;
+
+	if (vendor == (u16) ~0 || vendor == 0)
+		return false;
+
+	return true;
+}
+
+static int mhi_pci_claim(struct mhi_controller *mhi_cntrl,
+			 unsigned int bar_num, u64 dma_mask)
+{
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	int err;
+
+	err = pci_assign_resource(pdev, bar_num);
+	if (err)
+		return err;
+
+	err = pcim_enable_device(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable pci device: %d\n", err);
+		return err;
+	}
+
+	err = pcim_iomap_regions(pdev, 1 << bar_num, pci_name(pdev));
+	if (err) {
+		dev_err(&pdev->dev, "failed to map pci region: %d\n", err);
+		return err;
+	}
+	mhi_cntrl->regs = pcim_iomap_table(pdev)[bar_num];
+	mhi_cntrl->reg_len = pci_resource_len(pdev, bar_num);
+
+	err = pci_set_dma_mask(pdev, dma_mask);
+	if (err) {
+		dev_err(&pdev->dev, "Cannot set proper DMA mask\n");
+		return err;
+	}
+
+	err = pci_set_consistent_dma_mask(pdev, dma_mask);
+	if (err) {
+		dev_err(&pdev->dev, "set consistent dma mask failed\n");
+		return err;
+	}
+
+	pci_set_master(pdev);
+
+	return 0;
+}
+
+static int mhi_pci_get_irqs(struct mhi_controller *mhi_cntrl,
+			    const struct mhi_controller_config *mhi_cntrl_config)
+{
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	int nr_vectors, i;
+	int *irq;
+
+	/*
+	 * Alloc one MSI vector for BHI + one vector per event ring, ideally...
+	 * No explicit pci_free_irq_vectors required, done by pcim_release.
+	 */
+	mhi_cntrl->nr_irqs = 1 + mhi_cntrl_config->num_events;
+
+	nr_vectors = pci_alloc_irq_vectors(pdev, 1, mhi_cntrl->nr_irqs, PCI_IRQ_MSI);
+	if (nr_vectors < 0) {
+		dev_err(&pdev->dev, "Error allocating MSI vectors %d\n",
+			nr_vectors);
+		return nr_vectors;
+	}
+
+	if (nr_vectors < mhi_cntrl->nr_irqs) {
+		dev_warn(&pdev->dev, "using shared MSI\n");
+
+		/* Patch msi vectors, use only one (shared) */
+		for (i = 0; i < mhi_cntrl_config->num_events; i++)
+			mhi_cntrl_config->event_cfg[i].irq = 0;
+		mhi_cntrl->nr_irqs = 1;
+	}
+
+	irq = devm_kcalloc(&pdev->dev, mhi_cntrl->nr_irqs, sizeof(int), GFP_KERNEL);
+	if (!irq)
+		return -ENOMEM;
+
+	for (i = 0; i < mhi_cntrl->nr_irqs; i++) {
+		int vector = i >= nr_vectors ? (nr_vectors - 1) : i;
+
+		irq[i] = pci_irq_vector(pdev, vector);
+	}
+
+	mhi_cntrl->irq = irq;
+
+	return 0;
+}
+
+static int mhi_pci_runtime_get(struct mhi_controller *mhi_cntrl)
+{
+	/* The runtime_get() MHI callback means:
+	 *    Do whatever is requested to leave M3.
+	 */
+	return pm_runtime_get(mhi_cntrl->cntrl_dev);
+}
+
+static void mhi_pci_runtime_put(struct mhi_controller *mhi_cntrl)
+{
+	/* The runtime_put() MHI callback means:
+	 *    Device can be moved in M3 state.
+	 */
+	pm_runtime_mark_last_busy(mhi_cntrl->cntrl_dev);
+	pm_runtime_put(mhi_cntrl->cntrl_dev);
+}
+
+static void mhi_pci_recovery_work(struct work_struct *work)
+{
+	struct mhi_pci_device *mhi_pdev = container_of(work, struct mhi_pci_device,
+						       recovery_work);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	int err;
+
+	dev_warn(&pdev->dev, "device recovery started\n");
+
+	del_timer(&mhi_pdev->health_check_timer);
+	pm_runtime_forbid(&pdev->dev);
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_load_saved_state(pdev, mhi_pdev->pci_state);
+	pci_restore_state(pdev);
+
+	if (!mhi_pci_is_alive(mhi_cntrl))
+		goto err_try_reset;
+
+	err = mhi_prepare_for_power_up(mhi_cntrl);
+	if (err)
+		goto err_try_reset;
+
+	err = mhi_sync_power_up(mhi_cntrl);
+	if (err)
+		goto err_unprepare;
+
+	dev_dbg(&pdev->dev, "Recovery completed\n");
+
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+	return;
+
+err_unprepare:
+	mhi_unprepare_after_power_down(mhi_cntrl);
+err_try_reset:
+	err = pci_try_reset_function(pdev);
+	if (err)
+		dev_err(&pdev->dev, "Recovery failed: %d\n", err);
+}
+
+static void health_check(struct timer_list *t)
+{
+	struct mhi_pci_device *mhi_pdev = from_timer(mhi_pdev, t, health_check_timer);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	if (!test_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status) ||
+			test_bit(MHI_PCI_DEV_SUSPENDED, &mhi_pdev->status))
+		return;
+
+	if (!mhi_pci_is_alive(mhi_cntrl)) {
+		dev_err(mhi_cntrl->cntrl_dev, "Device died\n");
+		queue_work(system_long_wq, &mhi_pdev->recovery_work);
+		return;
+	}
+
+	/* reschedule in two seconds */
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+}
+
+static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
+	const struct mhi_controller_config *mhi_cntrl_config;
+	struct mhi_pci_device *mhi_pdev;
+	struct mhi_controller *mhi_cntrl;
+	int err;
+
+	dev_dbg(&pdev->dev, "MHI PCI device found: %s\n", info->name);
+
+	/* mhi_pdev.mhi_cntrl must be zero-initialized */
+	mhi_pdev = devm_kzalloc(&pdev->dev, sizeof(*mhi_pdev), GFP_KERNEL);
+	if (!mhi_pdev)
+		return -ENOMEM;
+
+	INIT_WORK(&mhi_pdev->recovery_work, mhi_pci_recovery_work);
+	timer_setup(&mhi_pdev->health_check_timer, health_check, 0);
+
+	mhi_cntrl_config = info->config;
+	mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	mhi_cntrl->cntrl_dev = &pdev->dev;
+	mhi_cntrl->iova_start = 0;
+	mhi_cntrl->iova_stop = (dma_addr_t)DMA_BIT_MASK(info->dma_data_width);
+	mhi_cntrl->fw_image = info->fw;
+	mhi_cntrl->edl_image = info->edl;
+
+	mhi_cntrl->read_reg = mhi_pci_read_reg;
+	mhi_cntrl->write_reg = mhi_pci_write_reg;
+	mhi_cntrl->status_cb = mhi_pci_status_cb;
+	mhi_cntrl->runtime_get = mhi_pci_runtime_get;
+	mhi_cntrl->runtime_put = mhi_pci_runtime_put;
+	mhi_cntrl->mru = info->mru_default;
+
+	if (info->sideband_wake) {
+		mhi_cntrl->wake_get = mhi_pci_wake_get_nop;
+		mhi_cntrl->wake_put = mhi_pci_wake_put_nop;
+		mhi_cntrl->wake_toggle = mhi_pci_wake_toggle_nop;
+	}
+
+	err = mhi_pci_claim(mhi_cntrl, info->bar_num, DMA_BIT_MASK(info->dma_data_width));
+	if (err)
+		return err;
+
+	err = mhi_pci_get_irqs(mhi_cntrl, mhi_cntrl_config);
+	if (err)
+		return err;
+
+	pci_set_drvdata(pdev, mhi_pdev);
+
+	/* Have stored pci confspace at hand for restore in sudden PCI error.
+	 * cache the state locally and discard the PCI core one.
+	 */
+	pci_save_state(pdev);
+	mhi_pdev->pci_state = pci_store_saved_state(pdev);
+	pci_load_saved_state(pdev, NULL);
+
+	pci_enable_pcie_error_reporting(pdev);
+
+	err = mhi_register_controller(mhi_cntrl, mhi_cntrl_config);
+	if (err)
+		goto err_disable_reporting;
+
+	/* MHI bus does not power up the controller by default */
+	err = mhi_prepare_for_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to prepare MHI controller\n");
+		goto err_unregister;
+	}
+
+	err = mhi_sync_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to power up MHI controller\n");
+		goto err_unprepare;
+	}
+
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+
+	/* start health check */
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+
+	/* Only allow runtime-suspend if PME capable (for wakeup) */
+	if (pci_pme_capable(pdev, PCI_D3hot)) {
+		pm_runtime_set_autosuspend_delay(&pdev->dev, 2000);
+		pm_runtime_use_autosuspend(&pdev->dev);
+		pm_runtime_mark_last_busy(&pdev->dev);
+		pm_runtime_put_noidle(&pdev->dev);
+	}
+
+	return 0;
+
+err_unprepare:
+	mhi_unprepare_after_power_down(mhi_cntrl);
+err_unregister:
+	mhi_unregister_controller(mhi_cntrl);
+err_disable_reporting:
+	pci_disable_pcie_error_reporting(pdev);
+
+	return err;
+}
+
+static void mhi_pci_remove(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	del_timer_sync(&mhi_pdev->health_check_timer);
+	cancel_work_sync(&mhi_pdev->recovery_work);
+
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, true);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	/* balancing probe put_noidle */
+	if (pci_pme_capable(pdev, PCI_D3hot))
+		pm_runtime_get_noresume(&pdev->dev);
+
+	mhi_unregister_controller(mhi_cntrl);
+	pci_disable_pcie_error_reporting(pdev);
+}
+
+static void mhi_pci_shutdown(struct pci_dev *pdev)
+{
+	mhi_pci_remove(pdev);
+	pci_set_power_state(pdev, PCI_D3hot);
+}
+
+static void mhi_pci_reset_prepare(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	dev_info(&pdev->dev, "reset\n");
+
+	del_timer(&mhi_pdev->health_check_timer);
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	/* cause internal device reset */
+	mhi_soc_reset(mhi_cntrl);
+
+	/* Be sure device reset has been executed */
+	msleep(MHI_POST_RESET_DELAY_MS);
+}
+
+static void mhi_pci_reset_done(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	int err;
+
+	/* Restore initial known working PCI state */
+	pci_load_saved_state(pdev, mhi_pdev->pci_state);
+	pci_restore_state(pdev);
+
+	/* Is device status available ? */
+	if (!mhi_pci_is_alive(mhi_cntrl)) {
+		dev_err(&pdev->dev, "reset failed\n");
+		return;
+	}
+
+	err = mhi_prepare_for_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to prepare MHI controller\n");
+		return;
+	}
+
+	err = mhi_sync_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to power up MHI controller\n");
+		mhi_unprepare_after_power_down(mhi_cntrl);
+		return;
+	}
+
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+}
+
+static pci_ers_result_t mhi_pci_error_detected(struct pci_dev *pdev,
+					       pci_channel_state_t state)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	dev_err(&pdev->dev, "PCI error detected, state = %u\n", state);
+
+	if (state == pci_channel_io_perm_failure)
+		return PCI_ERS_RESULT_DISCONNECT;
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	} else {
+		/* Nothing to do */
+		return PCI_ERS_RESULT_RECOVERED;
+	}
+
+	pci_disable_device(pdev);
+
+	return PCI_ERS_RESULT_NEED_RESET;
+}
+
+static pci_ers_result_t mhi_pci_slot_reset(struct pci_dev *pdev)
+{
+	if (pci_enable_device(pdev)) {
+		dev_err(&pdev->dev, "Cannot re-enable PCI device after reset.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+
+	return PCI_ERS_RESULT_RECOVERED;
+}
+
+static void mhi_pci_io_resume(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+
+	dev_err(&pdev->dev, "PCI slot reset done\n");
+
+	queue_work(system_long_wq, &mhi_pdev->recovery_work);
+}
+
+static const struct pci_error_handlers mhi_pci_err_handler = {
+	.error_detected = mhi_pci_error_detected,
+	.slot_reset = mhi_pci_slot_reset,
+	.resume = mhi_pci_io_resume,
+	.reset_prepare = mhi_pci_reset_prepare,
+	.reset_done = mhi_pci_reset_done,
+};
+
+static int  __maybe_unused mhi_pci_runtime_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	int err;
+
+	if (test_and_set_bit(MHI_PCI_DEV_SUSPENDED, &mhi_pdev->status))
+		return 0;
+
+	del_timer(&mhi_pdev->health_check_timer);
+	cancel_work_sync(&mhi_pdev->recovery_work);
+
+	if (!test_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status) ||
+			mhi_cntrl->ee != MHI_EE_AMSS)
+		goto pci_suspend; /* Nothing to do at MHI level */
+
+	/* Transition to M3 state */
+	err = mhi_pm_suspend(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to suspend device: %d\n", err);
+		clear_bit(MHI_PCI_DEV_SUSPENDED, &mhi_pdev->status);
+		return -EBUSY;
+	}
+
+pci_suspend:
+	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, true);
+
+	return 0;
+}
+
+static int __maybe_unused mhi_pci_runtime_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	int err;
+
+	if (!test_and_clear_bit(MHI_PCI_DEV_SUSPENDED, &mhi_pdev->status))
+		return 0;
+
+	err = pci_enable_device(pdev);
+	if (err)
+		goto err_recovery;
+
+	pci_set_master(pdev);
+	pci_wake_from_d3(pdev, false);
+
+	if (!test_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status) ||
+			mhi_cntrl->ee != MHI_EE_AMSS)
+		return 0; /* Nothing to do at MHI level */
+
+	/* Exit M3, transition to M0 state */
+	err = mhi_pm_resume(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to resume device: %d\n", err);
+		goto err_recovery;
+	}
+
+	/* Resume health check */
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+
+	/* It can be a remote wakeup (no mhi runtime_get), update access time */
+	pm_runtime_mark_last_busy(dev);
+
+	return 0;
+
+err_recovery:
+	/* Do not fail to not mess up our PCI device state, the device likely
+	 * lost power (d3cold) and we simply need to reset it from the recovery
+	 * procedure, trigger the recovery asynchronously to prevent system
+	 * suspend exit delaying.
+	 */
+	queue_work(system_long_wq, &mhi_pdev->recovery_work);
+	pm_runtime_mark_last_busy(dev);
+
+	return 0;
+}
+
+static int  __maybe_unused mhi_pci_suspend(struct device *dev)
+{
+	pm_runtime_disable(dev);
+	return mhi_pci_runtime_suspend(dev);
+}
+
+static int __maybe_unused mhi_pci_resume(struct device *dev)
+{
+	int ret;
+
+	/* Depending the platform, device may have lost power (d3cold), we need
+	 * to resume it now to check its state and recover when necessary.
+	 */
+	ret = mhi_pci_runtime_resume(dev);
+	pm_runtime_enable(dev);
+
+	return ret;
+}
+
+static int __maybe_unused mhi_pci_freeze(struct device *dev)
+{
+	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	/* We want to stop all operations, hibernation does not guarantee that
+	 * device will be in the same state as before freezing, especially if
+	 * the intermediate restore kernel reinitializes MHI device with new
+	 * context.
+	 */
+	flush_work(&mhi_pdev->recovery_work);
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, true);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	return 0;
+}
+
+static int __maybe_unused mhi_pci_restore(struct device *dev)
+{
+	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
+
+	/* Reinitialize the device */
+	queue_work(system_long_wq, &mhi_pdev->recovery_work);
+
+	return 0;
+}
+
+static const struct dev_pm_ops mhi_pci_pm_ops = {
+	SET_RUNTIME_PM_OPS(mhi_pci_runtime_suspend, mhi_pci_runtime_resume, NULL)
+#ifdef CONFIG_PM_SLEEP
+	.suspend = mhi_pci_suspend,
+	.resume = mhi_pci_resume,
+	.freeze = mhi_pci_freeze,
+	.thaw = mhi_pci_restore,
+	.poweroff = mhi_pci_freeze,
+	.restore = mhi_pci_restore,
+#endif
+};
+
+static struct pci_driver mhi_pci_driver = {
+	.name		= "mhi-pci-generic",
+	.id_table	= mhi_pci_id_table,
+	.probe		= mhi_pci_probe,
+	.remove		= mhi_pci_remove,
+	.shutdown	= mhi_pci_shutdown,
+	.err_handler	= &mhi_pci_err_handler,
+	.driver.pm	= &mhi_pci_pm_ops
+};
+module_pci_driver(mhi_pci_driver);
+
+MODULE_AUTHOR("Loic Poulain <loic.poulain@linaro.org>");
+MODULE_DESCRIPTION("Modem Host Interface (MHI) PCI controller driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mhi/host/pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mhi/host/pm.c
@@ -0,0 +1,1266 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-direction.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/mhi.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+#include "internal.h"
+
+/*
+ * Not all MHI state transitions are synchronous. Transitions like Linkdown,
+ * SYS_ERR, and shutdown can happen anytime asynchronously. This function will
+ * transition to a new state only if we're allowed to.
+ *
+ * Priority increases as we go down. For instance, from any state in L0, the
+ * transition can be made to states in L1, L2 and L3. A notable exception to
+ * this rule is state DISABLE.  From DISABLE state we can only transition to
+ * POR state. Also, while in L2 state, user cannot jump back to previous
+ * L1 or L0 states.
+ *
+ * Valid transitions:
+ * L0: DISABLE <--> POR
+ *     POR <--> POR
+ *     POR -> M0 -> M2 --> M0
+ *     POR -> FW_DL_ERR
+ *     FW_DL_ERR <--> FW_DL_ERR
+ *     M0 <--> M0
+ *     M0 -> FW_DL_ERR
+ *     M0 -> M3_ENTER -> M3 -> M3_EXIT --> M0
+ * L1: SYS_ERR_DETECT -> SYS_ERR_PROCESS --> POR
+ * L2: SHUTDOWN_PROCESS -> LD_ERR_FATAL_DETECT
+ *     SHUTDOWN_PROCESS -> DISABLE
+ * L3: LD_ERR_FATAL_DETECT <--> LD_ERR_FATAL_DETECT
+ *     LD_ERR_FATAL_DETECT -> DISABLE
+ */
+static struct mhi_pm_transitions const dev_state_transitions[] = {
+	/* L0 States */
+	{
+		MHI_PM_DISABLE,
+		MHI_PM_POR
+	},
+	{
+		MHI_PM_POR,
+		MHI_PM_POR | MHI_PM_DISABLE | MHI_PM_M0 |
+		MHI_PM_SYS_ERR_DETECT | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT | MHI_PM_FW_DL_ERR
+	},
+	{
+		MHI_PM_M0,
+		MHI_PM_M0 | MHI_PM_M2 | MHI_PM_M3_ENTER |
+		MHI_PM_SYS_ERR_DETECT | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT | MHI_PM_FW_DL_ERR
+	},
+	{
+		MHI_PM_M2,
+		MHI_PM_M0 | MHI_PM_SYS_ERR_DETECT | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	{
+		MHI_PM_M3_ENTER,
+		MHI_PM_M3 | MHI_PM_SYS_ERR_DETECT | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	{
+		MHI_PM_M3,
+		MHI_PM_M3_EXIT | MHI_PM_SYS_ERR_DETECT |
+		MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	{
+		MHI_PM_M3_EXIT,
+		MHI_PM_M0 | MHI_PM_SYS_ERR_DETECT | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	{
+		MHI_PM_FW_DL_ERR,
+		MHI_PM_FW_DL_ERR | MHI_PM_SYS_ERR_DETECT |
+		MHI_PM_SHUTDOWN_PROCESS | MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	/* L1 States */
+	{
+		MHI_PM_SYS_ERR_DETECT,
+		MHI_PM_SYS_ERR_PROCESS | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	{
+		MHI_PM_SYS_ERR_PROCESS,
+		MHI_PM_POR | MHI_PM_SHUTDOWN_PROCESS |
+		MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	/* L2 States */
+	{
+		MHI_PM_SHUTDOWN_PROCESS,
+		MHI_PM_DISABLE | MHI_PM_LD_ERR_FATAL_DETECT
+	},
+	/* L3 States */
+	{
+		MHI_PM_LD_ERR_FATAL_DETECT,
+		MHI_PM_LD_ERR_FATAL_DETECT | MHI_PM_DISABLE
+	},
+};
+
+enum mhi_pm_state __must_check mhi_tryset_pm_state(struct mhi_controller *mhi_cntrl,
+						   enum mhi_pm_state state)
+{
+	unsigned long cur_state = mhi_cntrl->pm_state;
+	int index = find_last_bit(&cur_state, 32);
+
+	if (unlikely(index >= ARRAY_SIZE(dev_state_transitions)))
+		return cur_state;
+
+	if (unlikely(dev_state_transitions[index].from_state != cur_state))
+		return cur_state;
+
+	if (unlikely(!(dev_state_transitions[index].to_states & state)))
+		return cur_state;
+
+	mhi_cntrl->pm_state = state;
+	return mhi_cntrl->pm_state;
+}
+
+void mhi_set_mhi_state(struct mhi_controller *mhi_cntrl, enum mhi_state state)
+{
+	if (state == MHI_STATE_RESET) {
+		mhi_write_reg_field(mhi_cntrl, mhi_cntrl->regs, MHICTRL,
+				    MHICTRL_RESET_MASK, MHICTRL_RESET_SHIFT, 1);
+	} else {
+		mhi_write_reg_field(mhi_cntrl, mhi_cntrl->regs, MHICTRL,
+				    MHICTRL_MHISTATE_MASK,
+				    MHICTRL_MHISTATE_SHIFT, state);
+	}
+}
+
+/* NOP for backward compatibility, host allowed to ring DB in M2 state */
+static void mhi_toggle_dev_wake_nop(struct mhi_controller *mhi_cntrl)
+{
+}
+
+static void mhi_toggle_dev_wake(struct mhi_controller *mhi_cntrl)
+{
+	mhi_cntrl->wake_get(mhi_cntrl, false);
+	mhi_cntrl->wake_put(mhi_cntrl, true);
+}
+
+/* Handle device ready state transition */
+int mhi_ready_state_transition(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_event *mhi_event;
+	enum mhi_pm_state cur_state;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	u32 interval_us = 25000; /* poll register field every 25 milliseconds */
+	int ret, i;
+
+	/* Check if device entered error state */
+	if (MHI_PM_IN_FATAL_STATE(mhi_cntrl->pm_state)) {
+		dev_err(dev, "Device link is not accessible\n");
+		return -EIO;
+	}
+
+	/* Wait for RESET to be cleared and READY bit to be set by the device */
+	ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs, MHICTRL,
+				 MHICTRL_RESET_MASK, MHICTRL_RESET_SHIFT, 0,
+				 interval_us);
+	if (ret) {
+		dev_err(dev, "Device failed to clear MHI Reset\n");
+		return ret;
+	}
+
+	ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs, MHISTATUS,
+				 MHISTATUS_READY_MASK, MHISTATUS_READY_SHIFT, 1,
+				 interval_us);
+	if (ret) {
+		dev_err(dev, "Device failed to enter MHI Ready\n");
+		return ret;
+	}
+
+	dev_dbg(dev, "Device in READY State\n");
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_POR);
+	mhi_cntrl->dev_state = MHI_STATE_READY;
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	if (cur_state != MHI_PM_POR) {
+		dev_err(dev, "Error moving to state %s from %s\n",
+			to_mhi_pm_state_str(MHI_PM_POR),
+			to_mhi_pm_state_str(cur_state));
+		return -EIO;
+	}
+
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (!MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state)) {
+		dev_err(dev, "Device registers not accessible\n");
+		goto error_mmio;
+	}
+
+	/* Configure MMIO registers */
+	ret = mhi_init_mmio(mhi_cntrl);
+	if (ret) {
+		dev_err(dev, "Error configuring MMIO registers\n");
+		goto error_mmio;
+	}
+
+	/* Add elements to all SW event rings */
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		/* Skip if this is an offload or HW event */
+		if (mhi_event->offload_ev || mhi_event->hw_ring)
+			continue;
+
+		ring->wp = ring->base + ring->len - ring->el_size;
+		*ring->ctxt_wp = cpu_to_le64(ring->iommu_base + ring->len - ring->el_size);
+		/* Update all cores */
+		smp_wmb();
+
+		/* Ring the event ring db */
+		spin_lock_irq(&mhi_event->lock);
+		mhi_ring_er_db(mhi_event);
+		spin_unlock_irq(&mhi_event->lock);
+	}
+
+	/* Set MHI to M0 state */
+	mhi_set_mhi_state(mhi_cntrl, MHI_STATE_M0);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	return 0;
+
+error_mmio:
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	return -EIO;
+}
+
+int mhi_pm_m0_transition(struct mhi_controller *mhi_cntrl)
+{
+	enum mhi_pm_state cur_state;
+	struct mhi_chan *mhi_chan;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	int i;
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	mhi_cntrl->dev_state = MHI_STATE_M0;
+	cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_M0);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+	if (unlikely(cur_state != MHI_PM_M0)) {
+		dev_err(dev, "Unable to transition to M0 state\n");
+		return -EIO;
+	}
+	mhi_cntrl->M0++;
+
+	/* Wake up the device */
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	mhi_cntrl->wake_get(mhi_cntrl, true);
+
+	/* Ring all event rings and CMD ring only if we're in mission mode */
+	if (MHI_IN_MISSION_MODE(mhi_cntrl->ee)) {
+		struct mhi_event *mhi_event = mhi_cntrl->mhi_event;
+		struct mhi_cmd *mhi_cmd =
+			&mhi_cntrl->mhi_cmd[PRIMARY_CMD_RING];
+
+		for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+			if (mhi_event->offload_ev)
+				continue;
+
+			spin_lock_irq(&mhi_event->lock);
+			mhi_ring_er_db(mhi_event);
+			spin_unlock_irq(&mhi_event->lock);
+		}
+
+		/* Only ring primary cmd ring if ring is not empty */
+		spin_lock_irq(&mhi_cmd->lock);
+		if (mhi_cmd->ring.rp != mhi_cmd->ring.wp)
+			mhi_ring_cmd_db(mhi_cntrl, mhi_cmd);
+		spin_unlock_irq(&mhi_cmd->lock);
+	}
+
+	/* Ring channel DB registers */
+	mhi_chan = mhi_cntrl->mhi_chan;
+	for (i = 0; i < mhi_cntrl->max_chan; i++, mhi_chan++) {
+		struct mhi_ring *tre_ring = &mhi_chan->tre_ring;
+
+		if (mhi_chan->db_cfg.reset_req) {
+			write_lock_irq(&mhi_chan->lock);
+			mhi_chan->db_cfg.db_mode = true;
+			write_unlock_irq(&mhi_chan->lock);
+		}
+
+		read_lock_irq(&mhi_chan->lock);
+
+		/* Only ring DB if ring is not empty */
+		if (tre_ring->base && tre_ring->wp  != tre_ring->rp &&
+		    mhi_chan->ch_state == MHI_CH_STATE_ENABLED)
+			mhi_ring_chan_db(mhi_cntrl, mhi_chan);
+		read_unlock_irq(&mhi_chan->lock);
+	}
+
+	mhi_cntrl->wake_put(mhi_cntrl, false);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+	wake_up_all(&mhi_cntrl->state_event);
+
+	return 0;
+}
+
+/*
+ * After receiving the MHI state change event from the device indicating the
+ * transition to M1 state, the host can transition the device to M2 state
+ * for keeping it in low power state.
+ */
+void mhi_pm_m1_transition(struct mhi_controller *mhi_cntrl)
+{
+	enum mhi_pm_state state;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_M2);
+	if (state == MHI_PM_M2) {
+		mhi_set_mhi_state(mhi_cntrl, MHI_STATE_M2);
+		mhi_cntrl->dev_state = MHI_STATE_M2;
+
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+
+		mhi_cntrl->M2++;
+		wake_up_all(&mhi_cntrl->state_event);
+
+		/* If there are any pending resources, exit M2 immediately */
+		if (unlikely(atomic_read(&mhi_cntrl->pending_pkts) ||
+			     atomic_read(&mhi_cntrl->dev_wake))) {
+			dev_dbg(dev,
+				"Exiting M2, pending_pkts: %d dev_wake: %d\n",
+				atomic_read(&mhi_cntrl->pending_pkts),
+				atomic_read(&mhi_cntrl->dev_wake));
+			read_lock_bh(&mhi_cntrl->pm_lock);
+			mhi_cntrl->wake_get(mhi_cntrl, true);
+			mhi_cntrl->wake_put(mhi_cntrl, true);
+			read_unlock_bh(&mhi_cntrl->pm_lock);
+		} else {
+			mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_IDLE);
+		}
+	} else {
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+	}
+}
+
+/* MHI M3 completion handler */
+int mhi_pm_m3_transition(struct mhi_controller *mhi_cntrl)
+{
+	enum mhi_pm_state state;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	mhi_cntrl->dev_state = MHI_STATE_M3;
+	state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_M3);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+	if (state != MHI_PM_M3) {
+		dev_err(dev, "Unable to transition to M3 state\n");
+		return -EIO;
+	}
+
+	mhi_cntrl->M3++;
+	wake_up_all(&mhi_cntrl->state_event);
+
+	return 0;
+}
+
+/* Handle device Mission Mode transition */
+static int mhi_pm_mission_mode_transition(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_event *mhi_event;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_ee_type ee = MHI_EE_MAX, current_ee = mhi_cntrl->ee;
+	int i, ret;
+
+	dev_dbg(dev, "Processing Mission Mode transition\n");
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	if (MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state))
+		ee = mhi_get_exec_env(mhi_cntrl);
+
+	if (!MHI_IN_MISSION_MODE(ee)) {
+		mhi_cntrl->pm_state = MHI_PM_LD_ERR_FATAL_DETECT;
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		wake_up_all(&mhi_cntrl->state_event);
+		return -EIO;
+	}
+	mhi_cntrl->ee = ee;
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	wake_up_all(&mhi_cntrl->state_event);
+
+	device_for_each_child(&mhi_cntrl->mhi_dev->dev, &current_ee,
+			      mhi_destroy_device);
+	mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_MISSION_MODE);
+
+	/* Force MHI to be in M0 state before continuing */
+	ret = __mhi_device_get_sync(mhi_cntrl);
+	if (ret)
+		return ret;
+
+	read_lock_bh(&mhi_cntrl->pm_lock);
+
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		ret = -EIO;
+		goto error_mission_mode;
+	}
+
+	/* Add elements to all HW event rings */
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		if (mhi_event->offload_ev || !mhi_event->hw_ring)
+			continue;
+
+		ring->wp = ring->base + ring->len - ring->el_size;
+		*ring->ctxt_wp = cpu_to_le64(ring->iommu_base + ring->len - ring->el_size);
+		/* Update to all cores */
+		smp_wmb();
+
+		spin_lock_irq(&mhi_event->lock);
+		if (MHI_DB_ACCESS_VALID(mhi_cntrl))
+			mhi_ring_er_db(mhi_event);
+		spin_unlock_irq(&mhi_event->lock);
+	}
+
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	/*
+	 * The MHI devices are only created when the client device switches its
+	 * Execution Environment (EE) to either SBL or AMSS states
+	 */
+	mhi_create_devices(mhi_cntrl);
+
+	read_lock_bh(&mhi_cntrl->pm_lock);
+
+error_mission_mode:
+	mhi_cntrl->wake_put(mhi_cntrl, false);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	return ret;
+}
+
+/* Handle shutdown transitions */
+static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl)
+{
+	enum mhi_pm_state cur_state;
+	struct mhi_event *mhi_event;
+	struct mhi_cmd_ctxt *cmd_ctxt;
+	struct mhi_cmd *mhi_cmd;
+	struct mhi_event_ctxt *er_ctxt;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	int ret, i;
+
+	dev_dbg(dev, "Processing disable transition with PM state: %s\n",
+		to_mhi_pm_state_str(mhi_cntrl->pm_state));
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+
+	/* Trigger MHI RESET so that the device will not access host memory */
+	if (!MHI_PM_IN_FATAL_STATE(mhi_cntrl->pm_state)) {
+		/* Skip MHI RESET if in RDDM state */
+		if (mhi_cntrl->rddm_image && mhi_get_exec_env(mhi_cntrl) == MHI_EE_RDDM)
+			goto skip_mhi_reset;
+
+		dev_dbg(dev, "Triggering MHI Reset in device\n");
+		mhi_set_mhi_state(mhi_cntrl, MHI_STATE_RESET);
+
+		/* Wait for the reset bit to be cleared by the device */
+		ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs, MHICTRL,
+				 MHICTRL_RESET_MASK, MHICTRL_RESET_SHIFT, 0,
+				 25000);
+		if (ret)
+			dev_err(dev, "Device failed to clear MHI Reset\n");
+
+		/*
+		 * Device will clear BHI_INTVEC as a part of RESET processing,
+		 * hence re-program it
+		 */
+		mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
+	}
+
+skip_mhi_reset:
+	dev_dbg(dev,
+		 "Waiting for all pending event ring processing to complete\n");
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		if (mhi_event->offload_ev)
+			continue;
+		free_irq(mhi_cntrl->irq[mhi_event->irq], mhi_event);
+		tasklet_kill(&mhi_event->task);
+	}
+
+	/* Release lock and wait for all pending threads to complete */
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+	dev_dbg(dev, "Waiting for all pending threads to complete\n");
+	wake_up_all(&mhi_cntrl->state_event);
+
+	dev_dbg(dev, "Reset all active channels and remove MHI devices\n");
+	device_for_each_child(&mhi_cntrl->mhi_dev->dev, NULL, mhi_destroy_device);
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+
+	WARN_ON(atomic_read(&mhi_cntrl->dev_wake));
+	WARN_ON(atomic_read(&mhi_cntrl->pending_pkts));
+
+	/* Reset the ev rings and cmd rings */
+	dev_dbg(dev, "Resetting EV CTXT and CMD CTXT\n");
+	mhi_cmd = mhi_cntrl->mhi_cmd;
+	cmd_ctxt = mhi_cntrl->mhi_ctxt->cmd_ctxt;
+	for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++, cmd_ctxt++) {
+		struct mhi_ring *ring = &mhi_cmd->ring;
+
+		ring->rp = ring->base;
+		ring->wp = ring->base;
+		cmd_ctxt->rp = cmd_ctxt->rbase;
+		cmd_ctxt->wp = cmd_ctxt->rbase;
+	}
+
+	mhi_event = mhi_cntrl->mhi_event;
+	er_ctxt = mhi_cntrl->mhi_ctxt->er_ctxt;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, er_ctxt++,
+		     mhi_event++) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		/* Skip offload events */
+		if (mhi_event->offload_ev)
+			continue;
+
+		ring->rp = ring->base;
+		ring->wp = ring->base;
+		er_ctxt->rp = er_ctxt->rbase;
+		er_ctxt->wp = er_ctxt->rbase;
+	}
+
+	/* Move to disable state */
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_DISABLE);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+	if (unlikely(cur_state != MHI_PM_DISABLE))
+		dev_err(dev, "Error moving from PM state: %s to: %s\n",
+			to_mhi_pm_state_str(cur_state),
+			to_mhi_pm_state_str(MHI_PM_DISABLE));
+
+	dev_dbg(dev, "Exiting with PM state: %s, MHI state: %s\n",
+		to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		TO_MHI_STATE_STR(mhi_cntrl->dev_state));
+
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+}
+
+/* Handle system error transitions */
+static void mhi_pm_sys_error_transition(struct mhi_controller *mhi_cntrl)
+{
+	enum mhi_pm_state cur_state, prev_state;
+	enum dev_st_transition next_state;
+	struct mhi_event *mhi_event;
+	struct mhi_cmd_ctxt *cmd_ctxt;
+	struct mhi_cmd *mhi_cmd;
+	struct mhi_event_ctxt *er_ctxt;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	int ret, i;
+
+	dev_dbg(dev, "Transitioning from PM state: %s to: %s\n",
+		to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		to_mhi_pm_state_str(MHI_PM_SYS_ERR_PROCESS));
+
+	/* We must notify MHI control driver so it can clean up first */
+	mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_SYS_ERROR);
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	prev_state = mhi_cntrl->pm_state;
+	cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_SYS_ERR_PROCESS);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	if (cur_state != MHI_PM_SYS_ERR_PROCESS) {
+		dev_err(dev, "Failed to transition from PM state: %s to: %s\n",
+			to_mhi_pm_state_str(cur_state),
+			to_mhi_pm_state_str(MHI_PM_SYS_ERR_PROCESS));
+		goto exit_sys_error_transition;
+	}
+
+	mhi_cntrl->ee = MHI_EE_DISABLE_TRANSITION;
+	mhi_cntrl->dev_state = MHI_STATE_RESET;
+
+	/* Wake up threads waiting for state transition */
+	wake_up_all(&mhi_cntrl->state_event);
+
+	/* Trigger MHI RESET so that the device will not access host memory */
+	if (MHI_REG_ACCESS_VALID(prev_state)) {
+		u32 in_reset = -1;
+		unsigned long timeout = msecs_to_jiffies(mhi_cntrl->timeout_ms);
+
+		dev_dbg(dev, "Triggering MHI Reset in device\n");
+		mhi_set_mhi_state(mhi_cntrl, MHI_STATE_RESET);
+
+		/* Wait for the reset bit to be cleared by the device */
+		ret = wait_event_timeout(mhi_cntrl->state_event,
+					 mhi_read_reg_field(mhi_cntrl,
+							    mhi_cntrl->regs,
+							    MHICTRL,
+							    MHICTRL_RESET_MASK,
+							    MHICTRL_RESET_SHIFT,
+							    &in_reset) ||
+					!in_reset, timeout);
+		if (!ret || in_reset) {
+			dev_err(dev, "Device failed to exit MHI Reset state\n");
+			goto exit_sys_error_transition;
+		}
+
+		/*
+		 * Device will clear BHI_INTVEC as a part of RESET processing,
+		 * hence re-program it
+		 */
+		mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
+	}
+
+	dev_dbg(dev,
+		"Waiting for all pending event ring processing to complete\n");
+	mhi_event = mhi_cntrl->mhi_event;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+		if (mhi_event->offload_ev)
+			continue;
+		tasklet_kill(&mhi_event->task);
+	}
+
+	/* Release lock and wait for all pending threads to complete */
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+	dev_dbg(dev, "Waiting for all pending threads to complete\n");
+	wake_up_all(&mhi_cntrl->state_event);
+
+	dev_dbg(dev, "Reset all active channels and remove MHI devices\n");
+	device_for_each_child(&mhi_cntrl->mhi_dev->dev, NULL, mhi_destroy_device);
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+
+	WARN_ON(atomic_read(&mhi_cntrl->dev_wake));
+	WARN_ON(atomic_read(&mhi_cntrl->pending_pkts));
+
+	/* Reset the ev rings and cmd rings */
+	dev_dbg(dev, "Resetting EV CTXT and CMD CTXT\n");
+	mhi_cmd = mhi_cntrl->mhi_cmd;
+	cmd_ctxt = mhi_cntrl->mhi_ctxt->cmd_ctxt;
+	for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++, cmd_ctxt++) {
+		struct mhi_ring *ring = &mhi_cmd->ring;
+
+		ring->rp = ring->base;
+		ring->wp = ring->base;
+		cmd_ctxt->rp = cmd_ctxt->rbase;
+		cmd_ctxt->wp = cmd_ctxt->rbase;
+	}
+
+	mhi_event = mhi_cntrl->mhi_event;
+	er_ctxt = mhi_cntrl->mhi_ctxt->er_ctxt;
+	for (i = 0; i < mhi_cntrl->total_ev_rings; i++, er_ctxt++,
+	     mhi_event++) {
+		struct mhi_ring *ring = &mhi_event->ring;
+
+		/* Skip offload events */
+		if (mhi_event->offload_ev)
+			continue;
+
+		ring->rp = ring->base;
+		ring->wp = ring->base;
+		er_ctxt->rp = er_ctxt->rbase;
+		er_ctxt->wp = er_ctxt->rbase;
+	}
+
+	/* Transition to next state */
+	if (MHI_IN_PBL(mhi_get_exec_env(mhi_cntrl))) {
+		write_lock_irq(&mhi_cntrl->pm_lock);
+		cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_POR);
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		if (cur_state != MHI_PM_POR) {
+			dev_err(dev, "Error moving to state %s from %s\n",
+				to_mhi_pm_state_str(MHI_PM_POR),
+				to_mhi_pm_state_str(cur_state));
+			goto exit_sys_error_transition;
+		}
+		next_state = DEV_ST_TRANSITION_PBL;
+	} else {
+		next_state = DEV_ST_TRANSITION_READY;
+	}
+
+	mhi_queue_state_transition(mhi_cntrl, next_state);
+
+exit_sys_error_transition:
+	dev_dbg(dev, "Exiting with PM state: %s, MHI state: %s\n",
+		to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		TO_MHI_STATE_STR(mhi_cntrl->dev_state));
+
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+}
+
+/* Queue a new work item and schedule work */
+int mhi_queue_state_transition(struct mhi_controller *mhi_cntrl,
+			       enum dev_st_transition state)
+{
+	struct state_transition *item = kmalloc(sizeof(*item), GFP_ATOMIC);
+	unsigned long flags;
+
+	if (!item)
+		return -ENOMEM;
+
+	item->state = state;
+	spin_lock_irqsave(&mhi_cntrl->transition_lock, flags);
+	list_add_tail(&item->node, &mhi_cntrl->transition_list);
+	spin_unlock_irqrestore(&mhi_cntrl->transition_lock, flags);
+
+	queue_work(mhi_cntrl->hiprio_wq, &mhi_cntrl->st_worker);
+
+	return 0;
+}
+
+/* SYS_ERR worker */
+void mhi_pm_sys_err_handler(struct mhi_controller *mhi_cntrl)
+{
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+
+	/* skip if controller supports RDDM */
+	if (mhi_cntrl->rddm_image) {
+		dev_dbg(dev, "Controller supports RDDM, skip SYS_ERROR\n");
+		return;
+	}
+
+	mhi_queue_state_transition(mhi_cntrl, DEV_ST_TRANSITION_SYS_ERR);
+}
+
+/* Device State Transition worker */
+void mhi_pm_st_worker(struct work_struct *work)
+{
+	struct state_transition *itr, *tmp;
+	LIST_HEAD(head);
+	struct mhi_controller *mhi_cntrl = container_of(work,
+							struct mhi_controller,
+							st_worker);
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+
+	spin_lock_irq(&mhi_cntrl->transition_lock);
+	list_splice_tail_init(&mhi_cntrl->transition_list, &head);
+	spin_unlock_irq(&mhi_cntrl->transition_lock);
+
+	list_for_each_entry_safe(itr, tmp, &head, node) {
+		list_del(&itr->node);
+		dev_dbg(dev, "Handling state transition: %s\n",
+			TO_DEV_STATE_TRANS_STR(itr->state));
+
+		switch (itr->state) {
+		case DEV_ST_TRANSITION_PBL:
+			write_lock_irq(&mhi_cntrl->pm_lock);
+			if (MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state))
+				mhi_cntrl->ee = mhi_get_exec_env(mhi_cntrl);
+			write_unlock_irq(&mhi_cntrl->pm_lock);
+			mhi_fw_load_handler(mhi_cntrl);
+			break;
+		case DEV_ST_TRANSITION_SBL:
+			write_lock_irq(&mhi_cntrl->pm_lock);
+			mhi_cntrl->ee = MHI_EE_SBL;
+			write_unlock_irq(&mhi_cntrl->pm_lock);
+			/*
+			 * The MHI devices are only created when the client
+			 * device switches its Execution Environment (EE) to
+			 * either SBL or AMSS states
+			 */
+			mhi_create_devices(mhi_cntrl);
+			if (mhi_cntrl->fbc_download)
+				mhi_download_amss_image(mhi_cntrl);
+			break;
+		case DEV_ST_TRANSITION_MISSION_MODE:
+			mhi_pm_mission_mode_transition(mhi_cntrl);
+			break;
+		case DEV_ST_TRANSITION_FP:
+			write_lock_irq(&mhi_cntrl->pm_lock);
+			mhi_cntrl->ee = MHI_EE_FP;
+			write_unlock_irq(&mhi_cntrl->pm_lock);
+			mhi_create_devices(mhi_cntrl);
+			break;
+		case DEV_ST_TRANSITION_READY:
+			mhi_ready_state_transition(mhi_cntrl);
+			break;
+		case DEV_ST_TRANSITION_SYS_ERR:
+			mhi_pm_sys_error_transition(mhi_cntrl);
+			break;
+		case DEV_ST_TRANSITION_DISABLE:
+			mhi_pm_disable_transition(mhi_cntrl);
+			break;
+		default:
+			break;
+		}
+		kfree(itr);
+	}
+}
+
+int mhi_pm_suspend(struct mhi_controller *mhi_cntrl)
+{
+	struct mhi_chan *itr, *tmp;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_pm_state new_state;
+	int ret;
+
+	if (mhi_cntrl->pm_state == MHI_PM_DISABLE)
+		return -EINVAL;
+
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state))
+		return -EIO;
+
+	/* Return busy if there are any pending resources */
+	if (atomic_read(&mhi_cntrl->dev_wake) ||
+	    atomic_read(&mhi_cntrl->pending_pkts))
+		return -EBUSY;
+
+	/* Take MHI out of M2 state */
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	mhi_cntrl->wake_get(mhi_cntrl, false);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+				 mhi_cntrl->dev_state == MHI_STATE_M0 ||
+				 mhi_cntrl->dev_state == MHI_STATE_M1 ||
+				 MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state),
+				 msecs_to_jiffies(mhi_cntrl->timeout_ms));
+
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	mhi_cntrl->wake_put(mhi_cntrl, false);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	if (!ret || MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		dev_err(dev,
+			"Could not enter M0/M1 state");
+		return -EIO;
+	}
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+
+	if (atomic_read(&mhi_cntrl->dev_wake) ||
+	    atomic_read(&mhi_cntrl->pending_pkts)) {
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		return -EBUSY;
+	}
+
+	dev_dbg(dev, "Allowing M3 transition\n");
+	new_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_M3_ENTER);
+	if (new_state != MHI_PM_M3_ENTER) {
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		dev_err(dev,
+			"Error setting to PM state: %s from: %s\n",
+			to_mhi_pm_state_str(MHI_PM_M3_ENTER),
+			to_mhi_pm_state_str(mhi_cntrl->pm_state));
+		return -EIO;
+	}
+
+	/* Set MHI to M3 and wait for completion */
+	mhi_set_mhi_state(mhi_cntrl, MHI_STATE_M3);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+	dev_dbg(dev, "Waiting for M3 completion\n");
+
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+				 mhi_cntrl->dev_state == MHI_STATE_M3 ||
+				 MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state),
+				 msecs_to_jiffies(mhi_cntrl->timeout_ms));
+
+	if (!ret || MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		dev_err(dev,
+			"Did not enter M3 state, MHI state: %s, PM state: %s\n",
+			TO_MHI_STATE_STR(mhi_cntrl->dev_state),
+			to_mhi_pm_state_str(mhi_cntrl->pm_state));
+		return -EIO;
+	}
+
+	/* Notify clients about entering LPM */
+	list_for_each_entry_safe(itr, tmp, &mhi_cntrl->lpm_chans, node) {
+		mutex_lock(&itr->mutex);
+		if (itr->mhi_dev)
+			mhi_notify(itr->mhi_dev, MHI_CB_LPM_ENTER);
+		mutex_unlock(&itr->mutex);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(mhi_pm_suspend);
+
+static int __mhi_pm_resume(struct mhi_controller *mhi_cntrl, bool force)
+{
+	struct mhi_chan *itr, *tmp;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	enum mhi_pm_state cur_state;
+	int ret;
+
+	dev_dbg(dev, "Entered with PM state: %s, MHI state: %s\n",
+		to_mhi_pm_state_str(mhi_cntrl->pm_state),
+		TO_MHI_STATE_STR(mhi_cntrl->dev_state));
+
+	if (mhi_cntrl->pm_state == MHI_PM_DISABLE)
+		return 0;
+
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state))
+		return -EIO;
+
+	if (mhi_get_mhi_state(mhi_cntrl) != MHI_STATE_M3) {
+		dev_warn(dev, "Resuming from non M3 state (%s)\n",
+			 TO_MHI_STATE_STR(mhi_get_mhi_state(mhi_cntrl)));
+		if (!force)
+			return -EINVAL;
+	}
+
+	/* Notify clients about exiting LPM */
+	list_for_each_entry_safe(itr, tmp, &mhi_cntrl->lpm_chans, node) {
+		mutex_lock(&itr->mutex);
+		if (itr->mhi_dev)
+			mhi_notify(itr->mhi_dev, MHI_CB_LPM_EXIT);
+		mutex_unlock(&itr->mutex);
+	}
+
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_M3_EXIT);
+	if (cur_state != MHI_PM_M3_EXIT) {
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		dev_info(dev,
+			 "Error setting to PM state: %s from: %s\n",
+			 to_mhi_pm_state_str(MHI_PM_M3_EXIT),
+			 to_mhi_pm_state_str(mhi_cntrl->pm_state));
+		return -EIO;
+	}
+
+	/* Set MHI to M0 and wait for completion */
+	mhi_set_mhi_state(mhi_cntrl, MHI_STATE_M0);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+				 mhi_cntrl->dev_state == MHI_STATE_M0 ||
+				 mhi_cntrl->dev_state == MHI_STATE_M2 ||
+				 MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state),
+				 msecs_to_jiffies(mhi_cntrl->timeout_ms));
+
+	if (!ret || MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		dev_err(dev,
+			"Did not enter M0 state, MHI state: %s, PM state: %s\n",
+			TO_MHI_STATE_STR(mhi_cntrl->dev_state),
+			to_mhi_pm_state_str(mhi_cntrl->pm_state));
+		return -EIO;
+	}
+
+	return 0;
+}
+
+int mhi_pm_resume(struct mhi_controller *mhi_cntrl)
+{
+	return __mhi_pm_resume(mhi_cntrl, false);
+}
+EXPORT_SYMBOL_GPL(mhi_pm_resume);
+
+int mhi_pm_resume_force(struct mhi_controller *mhi_cntrl)
+{
+	return __mhi_pm_resume(mhi_cntrl, true);
+}
+EXPORT_SYMBOL_GPL(mhi_pm_resume_force);
+
+int __mhi_device_get_sync(struct mhi_controller *mhi_cntrl)
+{
+	int ret;
+
+	/* Wake up the device */
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		read_unlock_bh(&mhi_cntrl->pm_lock);
+		return -EIO;
+	}
+	mhi_cntrl->wake_get(mhi_cntrl, true);
+	if (MHI_PM_IN_SUSPEND_STATE(mhi_cntrl->pm_state))
+		mhi_trigger_resume(mhi_cntrl);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+				 mhi_cntrl->pm_state == MHI_PM_M0 ||
+				 MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state),
+				 msecs_to_jiffies(mhi_cntrl->timeout_ms));
+
+	if (!ret || MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+		read_lock_bh(&mhi_cntrl->pm_lock);
+		mhi_cntrl->wake_put(mhi_cntrl, false);
+		read_unlock_bh(&mhi_cntrl->pm_lock);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+/* Assert device wake db */
+static void mhi_assert_dev_wake(struct mhi_controller *mhi_cntrl, bool force)
+{
+	unsigned long flags;
+
+	/*
+	 * If force flag is set, then increment the wake count value and
+	 * ring wake db
+	 */
+	if (unlikely(force)) {
+		spin_lock_irqsave(&mhi_cntrl->wlock, flags);
+		atomic_inc(&mhi_cntrl->dev_wake);
+		if (MHI_WAKE_DB_FORCE_SET_VALID(mhi_cntrl->pm_state) &&
+		    !mhi_cntrl->wake_set) {
+			mhi_write_db(mhi_cntrl, mhi_cntrl->wake_db, 1);
+			mhi_cntrl->wake_set = true;
+		}
+		spin_unlock_irqrestore(&mhi_cntrl->wlock, flags);
+	} else {
+		/*
+		 * If resources are already requested, then just increment
+		 * the wake count value and return
+		 */
+		if (likely(atomic_add_unless(&mhi_cntrl->dev_wake, 1, 0)))
+			return;
+
+		spin_lock_irqsave(&mhi_cntrl->wlock, flags);
+		if ((atomic_inc_return(&mhi_cntrl->dev_wake) == 1) &&
+		    MHI_WAKE_DB_SET_VALID(mhi_cntrl->pm_state) &&
+		    !mhi_cntrl->wake_set) {
+			mhi_write_db(mhi_cntrl, mhi_cntrl->wake_db, 1);
+			mhi_cntrl->wake_set = true;
+		}
+		spin_unlock_irqrestore(&mhi_cntrl->wlock, flags);
+	}
+}
+
+/* De-assert device wake db */
+static void mhi_deassert_dev_wake(struct mhi_controller *mhi_cntrl,
+				  bool override)
+{
+	unsigned long flags;
+
+	/*
+	 * Only continue if there is a single resource, else just decrement
+	 * and return
+	 */
+	if (likely(atomic_add_unless(&mhi_cntrl->dev_wake, -1, 1)))
+		return;
+
+	spin_lock_irqsave(&mhi_cntrl->wlock, flags);
+	if ((atomic_dec_return(&mhi_cntrl->dev_wake) == 0) &&
+	    MHI_WAKE_DB_CLEAR_VALID(mhi_cntrl->pm_state) && !override &&
+	    mhi_cntrl->wake_set) {
+		mhi_write_db(mhi_cntrl, mhi_cntrl->wake_db, 0);
+		mhi_cntrl->wake_set = false;
+	}
+	spin_unlock_irqrestore(&mhi_cntrl->wlock, flags);
+}
+
+int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
+{
+	enum mhi_state state;
+	enum mhi_ee_type current_ee;
+	enum dev_st_transition next_state;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	u32 interval_us = 25000; /* poll register field every 25 milliseconds */
+	int ret;
+
+	dev_info(dev, "Requested to power ON\n");
+
+	/* Supply default wake routines if not provided by controller driver */
+	if (!mhi_cntrl->wake_get || !mhi_cntrl->wake_put ||
+	    !mhi_cntrl->wake_toggle) {
+		mhi_cntrl->wake_get = mhi_assert_dev_wake;
+		mhi_cntrl->wake_put = mhi_deassert_dev_wake;
+		mhi_cntrl->wake_toggle = (mhi_cntrl->db_access & MHI_PM_M2) ?
+			mhi_toggle_dev_wake_nop : mhi_toggle_dev_wake;
+	}
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+	mhi_cntrl->pm_state = MHI_PM_DISABLE;
+
+	/* Setup BHI INTVEC */
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
+	mhi_cntrl->pm_state = MHI_PM_POR;
+	mhi_cntrl->ee = MHI_EE_MAX;
+	current_ee = mhi_get_exec_env(mhi_cntrl);
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+
+	/* Confirm that the device is in valid exec env */
+	if (!MHI_IN_PBL(current_ee) && current_ee != MHI_EE_AMSS) {
+		dev_err(dev, "%s is not a valid EE for power on\n",
+			TO_MHI_EXEC_STR(current_ee));
+		ret = -EIO;
+		goto error_exit;
+	}
+
+	state = mhi_get_mhi_state(mhi_cntrl);
+	dev_dbg(dev, "Attempting power on with EE: %s, state: %s\n",
+		TO_MHI_EXEC_STR(current_ee), TO_MHI_STATE_STR(state));
+
+	if (state == MHI_STATE_SYS_ERR) {
+		mhi_set_mhi_state(mhi_cntrl, MHI_STATE_RESET);
+		ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs, MHICTRL,
+				 MHICTRL_RESET_MASK, MHICTRL_RESET_SHIFT, 0,
+				 interval_us);
+		if (ret) {
+			dev_info(dev, "Failed to reset MHI due to syserr state\n");
+			goto error_exit;
+		}
+
+		/*
+		 * device cleares INTVEC as part of RESET processing,
+		 * re-program it
+		 */
+		mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
+	}
+
+	ret = mhi_init_irq_setup(mhi_cntrl);
+	if (ret)
+		goto error_exit;
+
+	/* Transition to next state */
+	next_state = MHI_IN_PBL(current_ee) ?
+		DEV_ST_TRANSITION_PBL : DEV_ST_TRANSITION_READY;
+
+	mhi_queue_state_transition(mhi_cntrl, next_state);
+
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+
+	dev_info(dev, "Power on setup success\n");
+
+	return 0;
+
+error_exit:
+	mhi_cntrl->pm_state = MHI_PM_DISABLE;
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_async_power_up);
+
+void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful)
+{
+	enum mhi_pm_state cur_state, transition_state;
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+
+	mutex_lock(&mhi_cntrl->pm_mutex);
+	write_lock_irq(&mhi_cntrl->pm_lock);
+	cur_state = mhi_cntrl->pm_state;
+	if (cur_state == MHI_PM_DISABLE) {
+		write_unlock_irq(&mhi_cntrl->pm_lock);
+		mutex_unlock(&mhi_cntrl->pm_mutex);
+		return; /* Already powered down */
+	}
+
+	/* If it's not a graceful shutdown, force MHI to linkdown state */
+	transition_state = (graceful) ? MHI_PM_SHUTDOWN_PROCESS :
+			   MHI_PM_LD_ERR_FATAL_DETECT;
+
+	cur_state = mhi_tryset_pm_state(mhi_cntrl, transition_state);
+	if (cur_state != transition_state) {
+		dev_err(dev, "Failed to move to state: %s from: %s\n",
+			to_mhi_pm_state_str(transition_state),
+			to_mhi_pm_state_str(mhi_cntrl->pm_state));
+		/* Force link down or error fatal detected state */
+		mhi_cntrl->pm_state = MHI_PM_LD_ERR_FATAL_DETECT;
+	}
+
+	/* mark device inactive to avoid any further host processing */
+	mhi_cntrl->ee = MHI_EE_DISABLE_TRANSITION;
+	mhi_cntrl->dev_state = MHI_STATE_RESET;
+
+	wake_up_all(&mhi_cntrl->state_event);
+
+	write_unlock_irq(&mhi_cntrl->pm_lock);
+	mutex_unlock(&mhi_cntrl->pm_mutex);
+
+	mhi_queue_state_transition(mhi_cntrl, DEV_ST_TRANSITION_DISABLE);
+
+	/* Wait for shutdown to complete */
+	flush_work(&mhi_cntrl->st_worker);
+
+	free_irq(mhi_cntrl->irq[0], mhi_cntrl);
+}
+EXPORT_SYMBOL_GPL(mhi_power_down);
+
+int mhi_sync_power_up(struct mhi_controller *mhi_cntrl)
+{
+	int ret = mhi_async_power_up(mhi_cntrl);
+
+	if (ret)
+		return ret;
+
+	wait_event_timeout(mhi_cntrl->state_event,
+			   MHI_IN_MISSION_MODE(mhi_cntrl->ee) ||
+			   MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state),
+			   msecs_to_jiffies(mhi_cntrl->timeout_ms));
+
+	ret = (MHI_IN_MISSION_MODE(mhi_cntrl->ee)) ? 0 : -ETIMEDOUT;
+	if (ret)
+		mhi_power_down(mhi_cntrl, false);
+
+	return ret;
+}
+EXPORT_SYMBOL(mhi_sync_power_up);
+
+int mhi_force_rddm_mode(struct mhi_controller *mhi_cntrl)
+{
+	struct device *dev = &mhi_cntrl->mhi_dev->dev;
+	int ret;
+
+	/* Check if device is already in RDDM */
+	if (mhi_cntrl->ee == MHI_EE_RDDM)
+		return 0;
+
+	dev_dbg(dev, "Triggering SYS_ERR to force RDDM state\n");
+	mhi_set_mhi_state(mhi_cntrl, MHI_STATE_SYS_ERR);
+
+	/* Wait for RDDM event */
+	ret = wait_event_timeout(mhi_cntrl->state_event,
+				 mhi_cntrl->ee == MHI_EE_RDDM,
+				 msecs_to_jiffies(mhi_cntrl->timeout_ms));
+	ret = ret ? 0 : -EIO;
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_force_rddm_mode);
+
+void mhi_device_get(struct mhi_device *mhi_dev)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+
+	mhi_dev->dev_wake++;
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (MHI_PM_IN_SUSPEND_STATE(mhi_cntrl->pm_state))
+		mhi_trigger_resume(mhi_cntrl);
+
+	mhi_cntrl->wake_get(mhi_cntrl, true);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+}
+EXPORT_SYMBOL_GPL(mhi_device_get);
+
+int mhi_device_get_sync(struct mhi_device *mhi_dev)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+	int ret;
+
+	ret = __mhi_device_get_sync(mhi_cntrl);
+	if (!ret)
+		mhi_dev->dev_wake++;
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mhi_device_get_sync);
+
+void mhi_device_put(struct mhi_device *mhi_dev)
+{
+	struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
+
+	mhi_dev->dev_wake--;
+	read_lock_bh(&mhi_cntrl->pm_lock);
+	if (MHI_PM_IN_SUSPEND_STATE(mhi_cntrl->pm_state))
+		mhi_trigger_resume(mhi_cntrl);
+
+	mhi_cntrl->wake_put(mhi_cntrl, false);
+	read_unlock_bh(&mhi_cntrl->pm_lock);
+}
+EXPORT_SYMBOL_GPL(mhi_device_put);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/mips_cdmm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/mips_cdmm.c
@@ -351,6 +351,7 @@
 	np = of_find_compatible_node(NULL, NULL, "mti,mips-cdmm");
 	if (np) {
 		err = of_address_to_resource(np, 0, &res);
+		of_node_put(np);
 		if (!err)
 			return res.start;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/moxtet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/moxtet.c
@@ -832,6 +832,12 @@
 	return 0;
 }
 
+static const struct spi_device_id moxtet_spi_ids[] = {
+	{ "moxtet" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, moxtet_spi_ids);
+
 static const struct of_device_id moxtet_dt_ids[] = {
 	{ .compatible = "cznic,moxtet" },
 	{},
@@ -843,6 +849,7 @@
 		.name		= "moxtet",
 		.of_match_table = moxtet_dt_ids,
 	},
+	.id_table	= moxtet_spi_ids,
 	.probe		= moxtet_probe,
 	.remove		= moxtet_remove,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/sunxi-rsb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/sunxi-rsb.c
@@ -227,6 +227,8 @@
 
 	dev_dbg(&rdev->dev, "device %s registered\n", dev_name(&rdev->dev));
 
+	return rdev;
+
 err_device_add:
 	put_device(&rdev->dev);
 
@@ -269,6 +271,9 @@
 /* common code that starts a transfer */
 static int _sunxi_rsb_run_xfer(struct sunxi_rsb *rsb)
 {
+	u32 int_mask, status;
+	bool timeout;
+
 	if (readl(rsb->regs + RSB_CTRL) & RSB_CTRL_START_TRANS) {
 		dev_dbg(rsb->dev, "RSB transfer still in progress\n");
 		return -EBUSY;
@@ -276,13 +281,23 @@
 
 	reinit_completion(&rsb->complete);
 
-	writel(RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR | RSB_INTS_TRANS_OVER,
-	       rsb->regs + RSB_INTE);
+	int_mask = RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR | RSB_INTS_TRANS_OVER;
+	writel(int_mask, rsb->regs + RSB_INTE);
 	writel(RSB_CTRL_START_TRANS | RSB_CTRL_GLOBAL_INT_ENB,
 	       rsb->regs + RSB_CTRL);
 
-	if (!wait_for_completion_io_timeout(&rsb->complete,
-					    msecs_to_jiffies(100))) {
+	if (irqs_disabled()) {
+		timeout = readl_poll_timeout_atomic(rsb->regs + RSB_INTS,
+						    status, (status & int_mask),
+						    10, 100000);
+		writel(status, rsb->regs + RSB_INTS);
+	} else {
+		timeout = !wait_for_completion_io_timeout(&rsb->complete,
+							  msecs_to_jiffies(100));
+		status = rsb->status;
+	}
+
+	if (timeout) {
 		dev_dbg(rsb->dev, "RSB timeout\n");
 
 		/* abort the transfer */
@@ -294,18 +309,18 @@
 		return -ETIMEDOUT;
 	}
 
-	if (rsb->status & RSB_INTS_LOAD_BSY) {
+	if (status & RSB_INTS_LOAD_BSY) {
 		dev_dbg(rsb->dev, "RSB busy\n");
 		return -EBUSY;
 	}
 
-	if (rsb->status & RSB_INTS_TRANS_ERR) {
-		if (rsb->status & RSB_INTS_TRANS_ERR_ACK) {
+	if (status & RSB_INTS_TRANS_ERR) {
+		if (status & RSB_INTS_TRANS_ERR_ACK) {
 			dev_dbg(rsb->dev, "RSB slave nack\n");
 			return -EINVAL;
 		}
 
-		if (rsb->status & RSB_INTS_TRANS_ERR_DATA) {
+		if (status & RSB_INTS_TRANS_ERR_DATA) {
 			dev_dbg(rsb->dev, "RSB transfer data error\n");
 			return -EIO;
 		}
@@ -687,11 +702,11 @@
 
 static void sunxi_rsb_hw_exit(struct sunxi_rsb *rsb)
 {
-	/* Keep the clock and PM reference counts consistent. */
-	if (pm_runtime_status_suspended(rsb->dev))
-		pm_runtime_resume(rsb->dev);
 	reset_control_assert(rsb->rstc);
-	clk_disable_unprepare(rsb->clk);
+
+	/* Keep the clock and PM reference counts consistent. */
+	if (!pm_runtime_status_suspended(rsb->dev))
+		clk_disable_unprepare(rsb->clk);
 }
 
 static int __maybe_unused sunxi_rsb_runtime_suspend(struct device *dev)
@@ -814,14 +829,6 @@
 	return 0;
 }
 
-static void sunxi_rsb_shutdown(struct platform_device *pdev)
-{
-	struct sunxi_rsb *rsb = platform_get_drvdata(pdev);
-
-	pm_runtime_disable(&pdev->dev);
-	sunxi_rsb_hw_exit(rsb);
-}
-
 static const struct dev_pm_ops sunxi_rsb_dev_pm_ops = {
 	SET_RUNTIME_PM_OPS(sunxi_rsb_runtime_suspend,
 			   sunxi_rsb_runtime_resume, NULL)
@@ -837,7 +844,6 @@
 static struct platform_driver sunxi_rsb_driver = {
 	.probe = sunxi_rsb_probe,
 	.remove	= sunxi_rsb_remove,
-	.shutdown = sunxi_rsb_shutdown,
 	.driver	= {
 		.name = RSB_CTRL_NAME,
 		.of_match_table = sunxi_rsb_of_match_table,
@@ -855,7 +861,13 @@
 		return ret;
 	}
 
-	return platform_driver_register(&sunxi_rsb_driver);
+	ret = platform_driver_register(&sunxi_rsb_driver);
+	if (ret) {
+		bus_unregister(&sunxi_rsb_bus);
+		return ret;
+	}
+
+	return 0;
 }
 module_init(sunxi_rsb_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/bus/ti-sysc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/bus/ti-sysc.c
@@ -6,6 +6,7 @@
 #include <linux/io.h>
 #include <linux/clk.h>
 #include <linux/clkdev.h>
+#include <linux/cpu_pm.h>
 #include <linux/delay.h>
 #include <linux/list.h>
 #include <linux/module.h>
@@ -17,6 +18,7 @@
 #include <linux/of_platform.h>
 #include <linux/slab.h>
 #include <linux/sys_soc.h>
+#include <linux/timekeeping.h>
 #include <linux/iopoll.h>
 
 #include <linux/platform_data/ti-sysc.h>
@@ -36,6 +38,7 @@
 	SOC_2420,
 	SOC_2430,
 	SOC_3430,
+	SOC_AM35,
 	SOC_3630,
 	SOC_4430,
 	SOC_4460,
@@ -51,11 +54,18 @@
 	struct list_head node;
 };
 
+struct sysc_module {
+	struct sysc *ddata;
+	struct list_head node;
+};
+
 struct sysc_soc_info {
 	unsigned long general_purpose:1;
 	enum sysc_soc soc;
-	struct mutex list_lock;			/* disabled modules list lock */
+	struct mutex list_lock;	/* disabled and restored modules list lock */
 	struct list_head disabled_modules;
+	struct list_head restored_modules;
+	struct notifier_block nb;
 };
 
 enum sysc_clocks {
@@ -223,37 +233,77 @@
 	return sysc_read(ddata, offset);
 }
 
-/* Poll on reset status */
-static int sysc_wait_softreset(struct sysc *ddata)
+static int sysc_poll_reset_sysstatus(struct sysc *ddata)
 {
-	u32 sysc_mask, syss_done, rstval;
-	int syss_offset, error = 0;
-
-	if (ddata->cap->regbits->srst_shift < 0)
-		return 0;
-
-	syss_offset = ddata->offsets[SYSC_SYSSTATUS];
-	sysc_mask = BIT(ddata->cap->regbits->srst_shift);
+	int error, retries;
+	u32 syss_done, rstval;
 
 	if (ddata->cfg.quirks & SYSS_QUIRK_RESETDONE_INVERTED)
 		syss_done = 0;
 	else
 		syss_done = ddata->cfg.syss_mask;
 
-	if (syss_offset >= 0) {
+	if (likely(!timekeeping_suspended)) {
 		error = readx_poll_timeout_atomic(sysc_read_sysstatus, ddata,
 				rstval, (rstval & ddata->cfg.syss_mask) ==
 				syss_done, 100, MAX_MODULE_SOFTRESET_WAIT);
+	} else {
+		retries = MAX_MODULE_SOFTRESET_WAIT;
+		while (retries--) {
+			rstval = sysc_read_sysstatus(ddata);
+			if ((rstval & ddata->cfg.syss_mask) == syss_done)
+				return 0;
+			udelay(2); /* Account for udelay flakeyness */
+		}
+		error = -ETIMEDOUT;
+	}
+
+	return error;
+}
 
-	} else if (ddata->cfg.quirks & SYSC_QUIRK_RESET_STATUS) {
+static int sysc_poll_reset_sysconfig(struct sysc *ddata)
+{
+	int error, retries;
+	u32 sysc_mask, rstval;
+
+	sysc_mask = BIT(ddata->cap->regbits->srst_shift);
+
+	if (likely(!timekeeping_suspended)) {
 		error = readx_poll_timeout_atomic(sysc_read_sysconfig, ddata,
 				rstval, !(rstval & sysc_mask),
 				100, MAX_MODULE_SOFTRESET_WAIT);
+	} else {
+		retries = MAX_MODULE_SOFTRESET_WAIT;
+		while (retries--) {
+			rstval = sysc_read_sysconfig(ddata);
+			if (!(rstval & sysc_mask))
+				return 0;
+			udelay(2); /* Account for udelay flakeyness */
+		}
+		error = -ETIMEDOUT;
 	}
 
 	return error;
 }
 
+/* Poll on reset status */
+static int sysc_wait_softreset(struct sysc *ddata)
+{
+	int syss_offset, error = 0;
+
+	if (ddata->cap->regbits->srst_shift < 0)
+		return 0;
+
+	syss_offset = ddata->offsets[SYSC_SYSSTATUS];
+
+	if (syss_offset >= 0)
+		error = sysc_poll_reset_sysstatus(ddata);
+	else if (ddata->cfg.quirks & SYSC_QUIRK_RESET_STATUS)
+		error = sysc_poll_reset_sysconfig(ddata);
+
+	return error;
+}
+
 static int sysc_add_named_clock_from_child(struct sysc *ddata,
 					   const char *name,
 					   const char *optfck_name)
@@ -1068,6 +1118,11 @@
 	if (ddata->cfg.quirks & (SYSC_QUIRK_SWSUP_SIDLE |
 				 SYSC_QUIRK_SWSUP_SIDLE_ACT)) {
 		best_mode = SYSC_IDLE_NO;
+
+		/* Clear WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg &= ~BIT(regbits->enwkup_shift);
 	} else {
 		best_mode = fls(ddata->cfg.sidlemodes) - 1;
 		if (best_mode > SYSC_IDLE_MASK) {
@@ -1188,6 +1243,13 @@
 		}
 	}
 
+	if (ddata->cfg.quirks & SYSC_QUIRK_SWSUP_SIDLE_ACT) {
+		/* Set WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg |= BIT(regbits->enwkup_shift);
+	}
+
 	reg &= ~(SYSC_IDLE_MASK << regbits->sidle_shift);
 	reg |= best_mode << regbits->sidle_shift;
 	if (regbits->autoidle_shift >= 0 &&
@@ -1447,14 +1509,16 @@
 	SYSC_QUIRK("sham", 0, 0x100, 0x110, 0x114, 0x40000c03, 0xffffffff,
 		   SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000046, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000052, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	/* Uarts on omap4 and later */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x50411e03, 0xffff00ff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
+	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47424e03, 0xffffffff,
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 
 	/* Quirks that need to be set based on the module address */
 	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -ENODEV, 0x50000800, 0xffffffff,
@@ -1518,7 +1582,7 @@
 		   0xffffffff, SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY),
 	SYSC_QUIRK("usb_otg_hs", 0, 0, 0x10, -ENODEV, 0x4ea2080d, 0xffffffff,
 		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY |
-		   SYSC_QUIRK_REINIT_ON_RESUME),
+		   SYSC_QUIRK_REINIT_ON_CTX_LOST),
 	SYSC_QUIRK("wdt", 0, 0, 0x10, 0x14, 0x502a0500, 0xfffff0f0,
 		   SYSC_MODULE_QUIRK_WDT),
 	/* PRUSS on am3, am4 and am5 */
@@ -1710,7 +1774,7 @@
 	if (!ddata->module_va)
 		return -EIO;
 
-	/* DISP_CONTROL */
+	/* DISP_CONTROL, shut down lcd and digit on disable if enabled */
 	val = sysc_read(ddata, dispc_offset + 0x40);
 	lcd_en = val & lcd_en_mask;
 	digit_en = val & digit_en_mask;
@@ -1722,7 +1786,7 @@
 		else
 			irq_mask |= BIT(2) | BIT(3);	/* EVSYNC bits */
 	}
-	if (disable & (lcd_en | digit_en))
+	if (disable && (lcd_en || digit_en))
 		sysc_write(ddata, dispc_offset + 0x40,
 			   val & ~(lcd_en_mask | digit_en_mask));
 
@@ -1778,7 +1842,7 @@
 		dev_warn(ddata->dev, "%s: timed out %08x !+ %08x\n",
 			 __func__, val, irq_mask);
 
-	if (sysc_soc->soc == SOC_3430) {
+	if (sysc_soc->soc == SOC_3430 || sysc_soc->soc == SOC_AM35) {
 		/* Clear DSS_SDI_CONTROL */
 		sysc_write(ddata, 0x44, 0);
 
@@ -2040,11 +2104,22 @@
 		sysc_val = sysc_read_sysconfig(ddata);
 		sysc_val |= sysc_mask;
 		sysc_write(ddata, sysc_offset, sysc_val);
-	}
 
-	if (ddata->cfg.srst_udelay)
-		usleep_range(ddata->cfg.srst_udelay,
-			     ddata->cfg.srst_udelay * 2);
+		/*
+		 * Some devices need a delay before reading registers
+		 * after reset. Presumably a srst_udelay is not needed
+		 * for devices that use a rstctrl register reset.
+		 */
+		if (ddata->cfg.srst_udelay)
+			fsleep(ddata->cfg.srst_udelay);
+
+		/*
+		 * Flush posted write. For devices needing srst_udelay
+		 * this should trigger an interconnect error if the
+		 * srst_udelay value is needed but not configured.
+		 */
+		sysc_val = sysc_read_sysconfig(ddata);
+	}
 
 	if (ddata->post_reset_quirk)
 		ddata->post_reset_quirk(ddata);
@@ -2401,6 +2476,78 @@
 	}
 };
 
+/* Caller needs to take list_lock if ever used outside of cpu_pm */
+static void sysc_reinit_modules(struct sysc_soc_info *soc)
+{
+	struct sysc_module *module;
+	struct list_head *pos;
+	struct sysc *ddata;
+
+	list_for_each(pos, &sysc_soc->restored_modules) {
+		module = list_entry(pos, struct sysc_module, node);
+		ddata = module->ddata;
+		sysc_reinit_module(ddata, ddata->enabled);
+	}
+}
+
+/**
+ * sysc_context_notifier - optionally reset and restore module after idle
+ * @nb: notifier block
+ * @cmd: unused
+ * @v: unused
+ *
+ * Some interconnect target modules need to be restored, or reset and restored
+ * on CPU_PM CPU_PM_CLUSTER_EXIT notifier. This is needed at least for am335x
+ * OTG and GPMC target modules even if the modules are unused.
+ */
+static int sysc_context_notifier(struct notifier_block *nb, unsigned long cmd,
+				 void *v)
+{
+	struct sysc_soc_info *soc;
+
+	soc = container_of(nb, struct sysc_soc_info, nb);
+
+	switch (cmd) {
+	case CPU_CLUSTER_PM_ENTER:
+		break;
+	case CPU_CLUSTER_PM_ENTER_FAILED:	/* No need to restore context */
+		break;
+	case CPU_CLUSTER_PM_EXIT:
+		sysc_reinit_modules(soc);
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+/**
+ * sysc_add_restored - optionally add reset and restore quirk hanlling
+ * @ddata: device data
+ */
+static void sysc_add_restored(struct sysc *ddata)
+{
+	struct sysc_module *restored_module;
+
+	restored_module = kzalloc(sizeof(*restored_module), GFP_KERNEL);
+	if (!restored_module)
+		return;
+
+	restored_module->ddata = ddata;
+
+	mutex_lock(&sysc_soc->list_lock);
+
+	list_add(&restored_module->node, &sysc_soc->restored_modules);
+
+	if (sysc_soc->nb.notifier_call)
+		goto out_unlock;
+
+	sysc_soc->nb.notifier_call = sysc_context_notifier;
+	cpu_pm_register_notifier(&sysc_soc->nb);
+
+out_unlock:
+	mutex_unlock(&sysc_soc->list_lock);
+}
+
 /**
  * sysc_legacy_idle_quirk - handle children in omap_device compatible way
  * @ddata: device driver data
@@ -2848,6 +2995,7 @@
 static const struct soc_device_attribute sysc_soc_match[] = {
 	SOC_FLAG("OMAP242*", SOC_2420),
 	SOC_FLAG("OMAP243*", SOC_2430),
+	SOC_FLAG("AM35*", SOC_AM35),
 	SOC_FLAG("OMAP3[45]*", SOC_3430),
 	SOC_FLAG("OMAP3[67]*", SOC_3630),
 	SOC_FLAG("OMAP443*", SOC_4430),
@@ -2900,12 +3048,14 @@
 }
 
 /*
- * One time init to detect the booted SoC and disable unavailable features.
+ * One time init to detect the booted SoC, disable unavailable features
+ * and initialize list for optional cpu_pm notifier.
+ *
  * Note that we initialize static data shared across all ti-sysc instances
  * so ddata is only used for SoC type. This can be called from module_init
  * once we no longer need to rely on platform data.
  */
-static int sysc_init_soc(struct sysc *ddata)
+static int sysc_init_static_data(struct sysc *ddata)
 {
 	const struct soc_device_attribute *match;
 	struct ti_sysc_platform_data *pdata;
@@ -2921,6 +3071,7 @@
 
 	mutex_init(&sysc_soc->list_lock);
 	INIT_LIST_HEAD(&sysc_soc->disabled_modules);
+	INIT_LIST_HEAD(&sysc_soc->restored_modules);
 	sysc_soc->general_purpose = true;
 
 	pdata = dev_get_platdata(ddata->dev);
@@ -2929,7 +3080,7 @@
 
 	match = soc_device_match(sysc_soc_match);
 	if (match && match->data)
-		sysc_soc->soc = (int)match->data;
+		sysc_soc->soc = (enum sysc_soc)(uintptr_t)match->data;
 
 	/*
 	 * Check and warn about possible old incomplete dtb. We now want to see
@@ -2985,15 +3136,24 @@
 	return 0;
 }
 
-static void sysc_cleanup_soc(void)
+static void sysc_cleanup_static_data(void)
 {
+	struct sysc_module *restored_module;
 	struct sysc_address *disabled_module;
 	struct list_head *pos, *tmp;
 
 	if (!sysc_soc)
 		return;
 
+	if (sysc_soc->nb.notifier_call)
+		cpu_pm_unregister_notifier(&sysc_soc->nb);
+
 	mutex_lock(&sysc_soc->list_lock);
+	list_for_each_safe(pos, tmp, &sysc_soc->restored_modules) {
+		restored_module = list_entry(pos, struct sysc_module, node);
+		list_del(pos);
+		kfree(restored_module);
+	}
 	list_for_each_safe(pos, tmp, &sysc_soc->disabled_modules) {
 		disabled_module = list_entry(pos, struct sysc_address, node);
 		list_del(pos);
@@ -3029,13 +3189,27 @@
  */
 static int sysc_check_active_timer(struct sysc *ddata)
 {
+	int error;
+
 	if (ddata->cap->type != TI_SYSC_OMAP2_TIMER &&
 	    ddata->cap->type != TI_SYSC_OMAP4_TIMER)
 		return 0;
 
+	/*
+	 * Quirk for omap3 beagleboard revision A to B4 to use gpt12.
+	 * Revision C and later are fixed with commit 23885389dbbb ("ARM:
+	 * dts: Fix timer regression for beagleboard revision c"). This all
+	 * can be dropped if we stop supporting old beagleboard revisions
+	 * A to B4 at some point.
+	 */
+	if (sysc_soc->soc == SOC_3430 || sysc_soc->soc == SOC_AM35)
+		error = -ENXIO;
+	else
+		error = -EBUSY;
+
 	if ((ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT) &&
 	    (ddata->cfg.quirks & SYSC_QUIRK_NO_IDLE))
-		return -ENXIO;
+		return error;
 
 	return 0;
 }
@@ -3061,7 +3235,7 @@
 	ddata->dev = &pdev->dev;
 	platform_set_drvdata(pdev, ddata);
 
-	error = sysc_init_soc(ddata);
+	error = sysc_init_static_data(ddata);
 	if (error)
 		return error;
 
@@ -3159,6 +3333,9 @@
 		pm_runtime_put(&pdev->dev);
 	}
 
+	if (ddata->cfg.quirks & SYSC_QUIRK_REINIT_ON_CTX_LOST)
+		sysc_add_restored(ddata);
+
 	return 0;
 
 err:
@@ -3175,7 +3352,9 @@
 	struct sysc *ddata = platform_get_drvdata(pdev);
 	int error;
 
-	cancel_delayed_work_sync(&ddata->idle_work);
+	/* Device can still be enabled, see deferred idle quirk in probe */
+	if (cancel_delayed_work_sync(&ddata->idle_work))
+		ti_sysc_idle(&ddata->idle_work.work);
 
 	error = pm_runtime_resume_and_get(ddata->dev);
 	if (error < 0) {
@@ -3240,7 +3419,7 @@
 {
 	bus_unregister_notifier(&platform_bus_type, &sysc_nb);
 	platform_driver_unregister(&sysc_driver);
-	sysc_cleanup_soc();
+	sysc_cleanup_static_data();
 }
 module_exit(sysc_exit);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cdrom/cdrom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cdrom/cdrom.c
@@ -291,7 +291,7 @@
 /* default compatibility mode */
 static bool autoclose=1;
 static bool autoeject;
-static bool lockdoor = 1;
+static bool lockdoor = 0;
 /* will we ever get to use this... sigh. */
 static bool check_media_type;
 /* automatically restart mrw format */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/Kconfig
@@ -428,27 +428,40 @@
 	  driver include crash and makedumpfile.
 
 config RANDOM_TRUST_CPU
-	bool "Trust the CPU manufacturer to initialize Linux's CRNG"
+	bool "Initialize RNG using CPU RNG instructions"
+	default y
 	depends on ARCH_RANDOM
-	default n
 	help
-	Assume that CPU manufacturer (e.g., Intel or AMD for RDSEED or
-	RDRAND, IBM for the S390 and Power PC architectures) is trustworthy
-	for the purposes of initializing Linux's CRNG.  Since this is not
-	something that can be independently audited, this amounts to trusting
-	that CPU manufacturer (perhaps with the insistence or mandate
-	of a Nation State's intelligence or law enforcement agencies)
-	has not installed a hidden back door to compromise the CPU's
-	random number generation facilities. This can also be configured
-	at boot with "random.trust_cpu=on/off".
+	  Initialize the RNG using random numbers supplied by the CPU's
+	  RNG instructions (e.g. RDRAND), if supported and available. These
+	  random numbers are never used directly, but are rather hashed into
+	  the main input pool, and this happens regardless of whether or not
+	  this option is enabled. Instead, this option controls whether the
+	  they are credited and hence can initialize the RNG. Additionally,
+	  other sources of randomness are always used, regardless of this
+	  setting.  Enabling this implies trusting that the CPU can supply high
+	  quality and non-backdoored random numbers.
+
+	  Say Y here unless you have reason to mistrust your CPU or believe
+	  its RNG facilities may be faulty. This may also be configured at
+	  boot time with "random.trust_cpu=on/off".
 
 config RANDOM_TRUST_BOOTLOADER
-	bool "Trust the bootloader to initialize Linux's CRNG"
+	bool "Initialize RNG using bootloader-supplied seed"
+	default y
 	help
-	Some bootloaders can provide entropy to increase the kernel's initial
-	device randomness. Say Y here to assume the entropy provided by the
-	booloader is trustworthy so it will be added to the kernel's entropy
-	pool. Otherwise, say N here so it will be regarded as device input that
-	only mixes the entropy pool.
+	  Initialize the RNG using a seed supplied by the bootloader or boot
+	  environment (e.g. EFI or a bootloader-generated device tree). This
+	  seed is not used directly, but is rather hashed into the main input
+	  pool, and this happens regardless of whether or not this option is
+	  enabled. Instead, this option controls whether the seed is credited
+	  and hence can initialize the RNG. Additionally, other sources of
+	  randomness are always used, regardless of this setting. Enabling
+	  this implies trusting that the bootloader can supply high quality and
+	  non-backdoored seeds.
+
+	  Say Y here unless you have reason to mistrust your bootloader or
+	  believe its RNG facilities may be faulty. This may also be configured
+	  at boot time with "random.trust_bootloader=on/off".
 
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/agp/parisc-agp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/agp/parisc-agp.c
@@ -90,6 +90,9 @@
 {
 	struct _parisc_agp_info *info = &parisc_agp_info;
 
+	/* force fdc ops to be visible to IOMMU */
+	asm_io_sync();
+
 	writeq(info->gart_base | ilog2(info->gart_size), info->ioc_regs+IOC_PCOM);
 	readq(info->ioc_regs+IOC_PCOM);	/* flush */
 }
@@ -158,6 +161,7 @@
 			info->gatt[j] =
 				parisc_agp_mask_memory(agp_bridge,
 					paddr, type);
+			asm_io_fdc(&info->gatt[j]);
 		}
 	}
 
@@ -191,7 +195,16 @@
 parisc_agp_mask_memory(struct agp_bridge_data *bridge, dma_addr_t addr,
 		       int type)
 {
-	return SBA_PDIR_VALID_BIT | addr;
+	unsigned ci;			/* coherent index */
+	dma_addr_t pa;
+
+	pa = addr & IOVP_MASK;
+	asm("lci 0(%1), %0" : "=r" (ci) : "r" (phys_to_virt(pa)));
+
+	pa |= (ci >> PAGE_SHIFT) & 0xff;/* move CI (8 bits) into lowest byte */
+	pa |= SBA_PDIR_VALID_BIT;	/* set "valid" bit */
+
+	return cpu_to_le64(pa);
 }
 
 static void
@@ -281,7 +294,7 @@
         return 0;
 }
 
-static int
+static int __init
 lba_find_capability(int cap)
 {
 	struct _parisc_agp_info *info = &parisc_agp_info;
@@ -366,7 +379,7 @@
 	return error;
 }
 
-static int
+static int __init
 find_quicksilver(struct device *dev, void *data)
 {
 	struct parisc_device **lba = data;
@@ -378,11 +391,9 @@
 	return 0;
 }
 
-static int
+static int __init
 parisc_agp_init(void)
 {
-	extern struct sba_device *sba_list;
-
 	int err = -1;
 	struct parisc_device *sba = NULL, *lba = NULL;
 	struct lba_device *lbadev = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/applicom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/applicom.c
@@ -197,8 +197,10 @@
 		if (!pci_match_id(applicom_pci_tbl, dev))
 			continue;
 		
-		if (pci_enable_device(dev))
+		if (pci_enable_device(dev)) {
+			pci_dev_put(dev);
 			return -EIO;
+		}
 
 		RamIO = ioremap(pci_resource_start(dev, 0), LEN_RAM_IO);
 
@@ -207,6 +209,7 @@
 				"space at 0x%llx\n",
 				(unsigned long long)pci_resource_start(dev, 0));
 			pci_disable_device(dev);
+			pci_dev_put(dev);
 			return -EIO;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hpet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hpet.c
@@ -304,8 +304,13 @@
 	if (!devp->hd_ireqfreq)
 		return -EIO;
 
-	if (count < sizeof(unsigned long))
-		return -EINVAL;
+	if (in_compat_syscall()) {
+		if (count < sizeof(compat_ulong_t))
+			return -EINVAL;
+	} else {
+		if (count < sizeof(unsigned long))
+			return -EINVAL;
+	}
 
 	add_wait_queue(&devp->hd_waitqueue, &wait);
 
@@ -329,9 +334,16 @@
 		schedule();
 	}
 
-	retval = put_user(data, (unsigned long __user *)buf);
-	if (!retval)
-		retval = sizeof(unsigned long);
+	if (in_compat_syscall()) {
+		retval = put_user(data, (compat_ulong_t __user *)buf);
+		if (!retval)
+			retval = sizeof(compat_ulong_t);
+	} else {
+		retval = put_user(data, (unsigned long __user *)buf);
+		if (!retval)
+			retval = sizeof(unsigned long);
+	}
+
 out:
 	__set_current_state(TASK_RUNNING);
 	remove_wait_queue(&devp->hd_waitqueue, &wait);
@@ -686,12 +698,24 @@
 	unsigned short hi_timer;
 };
 
+/* 32-bit types would lead to different command codes which should be
+ * translated into 64-bit ones before passed to hpet_ioctl_common
+ */
+#define COMPAT_HPET_INFO       _IOR('h', 0x03, struct compat_hpet_info)
+#define COMPAT_HPET_IRQFREQ    _IOW('h', 0x6, compat_ulong_t)
+
 static long
 hpet_compat_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 {
 	struct hpet_info info;
 	int err;
 
+	if (cmd == COMPAT_HPET_INFO)
+		cmd = HPET_INFO;
+
+	if (cmd == COMPAT_HPET_IRQFREQ)
+		cmd = HPET_IRQFREQ;
+
 	mutex_lock(&hpet_mutex);
 	err = hpet_ioctl_common(file->private_data, cmd, arg, &info);
 	mutex_unlock(&hpet_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/Kconfig
@@ -414,7 +414,7 @@
 
 config HW_RANDOM_CAVIUM
 	tristate "Cavium ThunderX Random Number Generator support"
-	depends on HW_RANDOM && PCI && (ARM64 || (COMPILE_TEST && 64BIT))
+	depends on HW_RANDOM && PCI && ARCH_THUNDER
 	default HW_RANDOM
 	help
 	  This driver provides kernel-side support for the Random Number
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/amd-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/amd-rng.c
@@ -142,16 +142,22 @@
 
 found:
 	err = pci_read_config_dword(pdev, 0x58, &pmbase);
-	if (err)
-		return err;
+	if (err) {
+		err = pcibios_err_to_errno(err);
+		goto put_dev;
+	}
 
 	pmbase &= 0x0000FF00;
-	if (pmbase == 0)
-		return -EIO;
+	if (pmbase == 0) {
+		err = -EIO;
+		goto put_dev;
+	}
 
 	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
+	if (!priv) {
+		err = -ENOMEM;
+		goto put_dev;
+	}
 
 	if (!request_region(pmbase + PMBASE_OFFSET, PMBASE_SIZE, DRV_NAME)) {
 		dev_err(&pdev->dev, DRV_NAME " region 0x%x already in use!\n",
@@ -185,6 +191,8 @@
 	release_region(pmbase + PMBASE_OFFSET, PMBASE_SIZE);
 out:
 	kfree(priv);
+put_dev:
+	pci_dev_put(pdev);
 	return err;
 }
 
@@ -200,6 +208,8 @@
 
 	release_region(priv->pmbase + PMBASE_OFFSET, PMBASE_SIZE);
 
+	pci_dev_put(priv->pcidev);
+
 	kfree(priv);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/arm_smccc_trng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/arm_smccc_trng.c
@@ -71,8 +71,6 @@
 				  MAX_BITS_PER_CALL);
 
 		arm_smccc_1_1_invoke(ARM_SMCCC_TRNG_RND, bits, &res);
-		if ((int)res.a0 < 0)
-			return (int)res.a0;
 
 		switch ((int)res.a0) {
 		case SMCCC_RET_SUCCESS:
@@ -88,6 +86,8 @@
 				return copied;
 			cond_resched();
 			break;
+		default:
+			return -EIO;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/atmel-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/atmel-rng.c
@@ -114,6 +114,7 @@
 
 err_register:
 	clk_disable_unprepare(trng->clk);
+	atmel_trng_disable(trng);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/bcm2835-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/bcm2835-rng.c
@@ -95,8 +95,10 @@
 		return ret;
 
 	ret = reset_control_reset(priv->reset);
-	if (ret)
+	if (ret) {
+		clk_disable_unprepare(priv->clk);
 		return ret;
+	}
 
 	if (priv->mask_interrupts) {
 		/* mask the interrupt */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/cavium-rng-vf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/cavium-rng-vf.c
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
- * Hardware Random Number Generator support for Cavium, Inc.
- * Thunder processor family.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
+ * Hardware Random Number Generator support.
+ * Cavium Thunder, Marvell OcteonTx/Tx2 processor families.
  *
  * Copyright (C) 2016 Cavium, Inc.
  */
@@ -15,16 +12,146 @@
 #include <linux/pci.h>
 #include <linux/pci_ids.h>
 
+#include <asm/arch_timer.h>
+
+/* PCI device IDs */
+#define	PCI_DEVID_CAVIUM_RNG_PF		0xA018
+#define	PCI_DEVID_CAVIUM_RNG_VF		0xA033
+
+#define HEALTH_STATUS_REG		0x38
+
+/* RST device info */
+#define PCI_DEVICE_ID_RST_OTX2		0xA085
+#define RST_BOOT_REG			0x1600ULL
+#define CLOCK_BASE_RATE			50000000ULL
+#define MSEC_TO_NSEC(x)			(x * 1000000)
+
 struct cavium_rng {
 	struct hwrng ops;
 	void __iomem *result;
+	void __iomem *pf_regbase;
+	struct pci_dev *pdev;
+	u64  clock_rate;
+	u64  prev_error;
+	u64  prev_time;
 };
 
+static inline bool is_octeontx(struct pci_dev *pdev)
+{
+	if (midr_is_cpu_model_range(read_cpuid_id(), MIDR_THUNDERX_83XX,
+				    MIDR_CPU_VAR_REV(0, 0),
+				    MIDR_CPU_VAR_REV(3, 0)) ||
+	    midr_is_cpu_model_range(read_cpuid_id(), MIDR_THUNDERX_81XX,
+				    MIDR_CPU_VAR_REV(0, 0),
+				    MIDR_CPU_VAR_REV(3, 0)) ||
+	    midr_is_cpu_model_range(read_cpuid_id(), MIDR_THUNDERX,
+				    MIDR_CPU_VAR_REV(0, 0),
+				    MIDR_CPU_VAR_REV(3, 0)))
+		return true;
+
+	return false;
+}
+
+static u64 rng_get_coprocessor_clkrate(void)
+{
+	u64 ret = CLOCK_BASE_RATE * 16; /* Assume 800Mhz as default */
+	struct pci_dev *pdev;
+	void __iomem *base;
+
+	pdev = pci_get_device(PCI_VENDOR_ID_CAVIUM,
+			      PCI_DEVICE_ID_RST_OTX2, NULL);
+	if (!pdev)
+		goto error;
+
+	base = pci_ioremap_bar(pdev, 0);
+	if (!base)
+		goto error_put_pdev;
+
+	/* RST: PNR_MUL * 50Mhz gives clockrate */
+	ret = CLOCK_BASE_RATE * ((readq(base + RST_BOOT_REG) >> 33) & 0x3F);
+
+	iounmap(base);
+
+error_put_pdev:
+	pci_dev_put(pdev);
+
+error:
+	return ret;
+}
+
+static int check_rng_health(struct cavium_rng *rng)
+{
+	u64 cur_err, cur_time;
+	u64 status, cycles;
+	u64 time_elapsed;
+
+
+	/* Skip checking health for OcteonTx */
+	if (!rng->pf_regbase)
+		return 0;
+
+	status = readq(rng->pf_regbase + HEALTH_STATUS_REG);
+	if (status & BIT_ULL(0)) {
+		dev_err(&rng->pdev->dev, "HWRNG: Startup health test failed\n");
+		return -EIO;
+	}
+
+	cycles = status >> 1;
+	if (!cycles)
+		return 0;
+
+	cur_time = arch_timer_read_counter();
+
+	/* RNM_HEALTH_STATUS[CYCLES_SINCE_HEALTH_FAILURE]
+	 * Number of coprocessor cycles times 2 since the last failure.
+	 * This field doesn't get cleared/updated until another failure.
+	 */
+	cycles = cycles / 2;
+	cur_err = (cycles * 1000000000) / rng->clock_rate; /* In nanosec */
+
+	/* Ignore errors that happenned a long time ago, these
+	 * are most likely false positive errors.
+	 */
+	if (cur_err > MSEC_TO_NSEC(10)) {
+		rng->prev_error = 0;
+		rng->prev_time = 0;
+		return 0;
+	}
+
+	if (rng->prev_error) {
+		/* Calculate time elapsed since last error
+		 * '1' tick of CNTVCT is 10ns, since it runs at 100Mhz.
+		 */
+		time_elapsed = (cur_time - rng->prev_time) * 10;
+		time_elapsed += rng->prev_error;
+
+		/* Check if current error is a new one or the old one itself.
+		 * If error is a new one then consider there is a persistent
+		 * issue with entropy, declare hardware failure.
+		 */
+		if (cur_err < time_elapsed) {
+			dev_err(&rng->pdev->dev, "HWRNG failure detected\n");
+			rng->prev_error = cur_err;
+			rng->prev_time = cur_time;
+			return -EIO;
+		}
+	}
+
+	rng->prev_error = cur_err;
+	rng->prev_time = cur_time;
+	return 0;
+}
+
 /* Read data from the RNG unit */
 static int cavium_rng_read(struct hwrng *rng, void *dat, size_t max, bool wait)
 {
 	struct cavium_rng *p = container_of(rng, struct cavium_rng, ops);
 	unsigned int size = max;
+	int err = 0;
+
+	err = check_rng_health(p);
+	if (err)
+		return err;
 
 	while (size >= 8) {
 		*((u64 *)dat) = readq(p->result);
@@ -39,6 +166,39 @@
 	return max;
 }
 
+static int cavium_map_pf_regs(struct cavium_rng *rng)
+{
+	struct pci_dev *pdev;
+
+	/* Health status is not supported on 83xx, skip mapping PF CSRs */
+	if (is_octeontx(rng->pdev)) {
+		rng->pf_regbase = NULL;
+		return 0;
+	}
+
+	pdev = pci_get_device(PCI_VENDOR_ID_CAVIUM,
+			      PCI_DEVID_CAVIUM_RNG_PF, NULL);
+	if (!pdev) {
+		dev_err(&pdev->dev, "Cannot find RNG PF device\n");
+		return -EIO;
+	}
+
+	rng->pf_regbase = ioremap(pci_resource_start(pdev, 0),
+				  pci_resource_len(pdev, 0));
+	if (!rng->pf_regbase) {
+		dev_err(&pdev->dev, "Failed to map PF CSR region\n");
+		pci_dev_put(pdev);
+		return -ENOMEM;
+	}
+
+	pci_dev_put(pdev);
+
+	/* Get co-processor clock rate */
+	rng->clock_rate = rng_get_coprocessor_clkrate();
+
+	return 0;
+}
+
 /* Map Cavium RNG to an HWRNG object */
 static int cavium_rng_probe_vf(struct	pci_dev		*pdev,
 			 const struct	pci_device_id	*id)
@@ -50,6 +210,8 @@
 	if (!rng)
 		return -ENOMEM;
 
+	rng->pdev = pdev;
+
 	/* Map the RNG result */
 	rng->result = pcim_iomap(pdev, 0, 0);
 	if (!rng->result) {
@@ -67,6 +229,11 @@
 
 	pci_set_drvdata(pdev, rng);
 
+	/* Health status is available only at PF, hence map PF registers. */
+	ret = cavium_map_pf_regs(rng);
+	if (ret)
+		return ret;
+
 	ret = devm_hwrng_register(&pdev->dev, &rng->ops);
 	if (ret) {
 		dev_err(&pdev->dev, "Error registering device as HWRNG.\n");
@@ -76,10 +243,18 @@
 	return 0;
 }
 
+/* Remove the VF */
+static void cavium_rng_remove_vf(struct pci_dev *pdev)
+{
+	struct cavium_rng *rng;
+
+	rng = pci_get_drvdata(pdev);
+	iounmap(rng->pf_regbase);
+}
 
 static const struct pci_device_id cavium_rng_vf_id_table[] = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_CAVIUM, 0xa033), 0, 0, 0},
-	{0,},
+	{ PCI_DEVICE(PCI_VENDOR_ID_CAVIUM, PCI_DEVID_CAVIUM_RNG_VF) },
+	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, cavium_rng_vf_id_table);
 
@@ -87,8 +262,9 @@
 	.name		= "cavium_rng_vf",
 	.id_table	= cavium_rng_vf_id_table,
 	.probe		= cavium_rng_probe_vf,
+	.remove		= cavium_rng_remove_vf,
 };
 module_pci_driver(cavium_rng_vf_driver);
 
 MODULE_AUTHOR("Omer Khaliq <okhaliq@caviumnetworks.com>");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/cavium-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/cavium-rng.c
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
- * Hardware Random Number Generator support for Cavium Inc.
- * Thunder processor family.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
+ * Hardware Random Number Generator support.
+ * Cavium Thunder, Marvell OcteonTx/Tx2 processor families.
  *
  * Copyright (C) 2016 Cavium, Inc.
  */
@@ -91,4 +88,4 @@
 
 module_pci_driver(cavium_rng_pf_driver);
 MODULE_AUTHOR("Omer Khaliq <okhaliq@caviumnetworks.com>");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/cctrng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/cctrng.c
@@ -665,6 +665,7 @@
 	/* wait for Cryptocell reset completion */
 	if (!cctrng_wait_for_reset_completion(drvdata)) {
 		dev_err(dev, "Cryptocell reset not completed");
+		clk_disable_unprepare(drvdata->clk);
 		return -EBUSY;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/core.c
@@ -15,6 +15,7 @@
 #include <linux/err.h>
 #include <linux/fs.h>
 #include <linux/hw_random.h>
+#include <linux/random.h>
 #include <linux/kernel.h>
 #include <linux/kthread.h>
 #include <linux/sched/signal.h>
@@ -23,10 +24,13 @@
 #include <linux/random.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
+#include <linux/string.h>
 #include <linux/uaccess.h>
 
 #define RNG_MODULE_NAME		"hw_random"
 
+#define RNG_BUFFER_SIZE (SMP_CACHE_BYTES < 32 ? 32 : SMP_CACHE_BYTES)
+
 static struct hwrng *current_rng;
 /* the current rng has been explicitly chosen by user via sysfs */
 static int cur_rng_set_by_user;
@@ -58,7 +62,7 @@
 
 static size_t rng_buffer_size(void)
 {
-	return SMP_CACHE_BYTES < 32 ? 32 : SMP_CACHE_BYTES;
+	return RNG_BUFFER_SIZE;
 }
 
 static void add_early_randomness(struct hwrng *rng)
@@ -205,6 +209,7 @@
 static ssize_t rng_dev_read(struct file *filp, char __user *buf,
 			    size_t size, loff_t *offp)
 {
+	u8 buffer[RNG_BUFFER_SIZE];
 	ssize_t ret = 0;
 	int err = 0;
 	int bytes_read, len;
@@ -232,34 +237,37 @@
 			if (bytes_read < 0) {
 				err = bytes_read;
 				goto out_unlock_reading;
+			} else if (bytes_read == 0 &&
+				   (filp->f_flags & O_NONBLOCK)) {
+				err = -EAGAIN;
+				goto out_unlock_reading;
 			}
+
 			data_avail = bytes_read;
 		}
 
-		if (!data_avail) {
-			if (filp->f_flags & O_NONBLOCK) {
-				err = -EAGAIN;
-				goto out_unlock_reading;
-			}
-		} else {
-			len = data_avail;
+		len = data_avail;
+		if (len) {
 			if (len > size)
 				len = size;
 
 			data_avail -= len;
 
-			if (copy_to_user(buf + ret, rng_buffer + data_avail,
-								len)) {
+			memcpy(buffer, rng_buffer + data_avail, len);
+		}
+		mutex_unlock(&reading_mutex);
+		put_rng(rng);
+
+		if (len) {
+			if (copy_to_user(buf + ret, buffer, len)) {
 				err = -EFAULT;
-				goto out_unlock_reading;
+				goto out;
 			}
 
 			size -= len;
 			ret += len;
 		}
 
-		mutex_unlock(&reading_mutex);
-		put_rng(rng);
 
 		if (need_resched())
 			schedule_timeout_interruptible(1);
@@ -270,6 +278,7 @@
 		}
 	}
 out:
+	memzero_explicit(buffer, sizeof(buffer));
 	return ret ? : err;
 
 out_unlock_reading:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/geode-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/geode-rng.c
@@ -51,10 +51,15 @@
 };
 MODULE_DEVICE_TABLE(pci, pci_tbl);
 
+struct amd_geode_priv {
+	struct pci_dev *pcidev;
+	void __iomem *membase;
+};
 
 static int geode_rng_data_read(struct hwrng *rng, u32 *data)
 {
-	void __iomem *mem = (void __iomem *)rng->priv;
+	struct amd_geode_priv *priv = (struct amd_geode_priv *)rng->priv;
+	void __iomem *mem = priv->membase;
 
 	*data = readl(mem + GEODE_RNG_DATA_REG);
 
@@ -63,7 +68,8 @@
 
 static int geode_rng_data_present(struct hwrng *rng, int wait)
 {
-	void __iomem *mem = (void __iomem *)rng->priv;
+	struct amd_geode_priv *priv = (struct amd_geode_priv *)rng->priv;
+	void __iomem *mem = priv->membase;
 	int data, i;
 
 	for (i = 0; i < 20; i++) {
@@ -90,6 +96,7 @@
 	const struct pci_device_id *ent;
 	void __iomem *mem;
 	unsigned long rng_base;
+	struct amd_geode_priv *priv;
 
 	for_each_pci_dev(pdev) {
 		ent = pci_match_id(pci_tbl, pdev);
@@ -97,17 +104,26 @@
 			goto found;
 	}
 	/* Device not found. */
-	goto out;
+	return err;
 
 found:
+	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+	if (!priv) {
+		err = -ENOMEM;
+		goto put_dev;
+	}
+
 	rng_base = pci_resource_start(pdev, 0);
 	if (rng_base == 0)
-		goto out;
+		goto free_priv;
 	err = -ENOMEM;
 	mem = ioremap(rng_base, 0x58);
 	if (!mem)
-		goto out;
-	geode_rng.priv = (unsigned long)mem;
+		goto free_priv;
+
+	geode_rng.priv = (unsigned long)priv;
+	priv->membase = mem;
+	priv->pcidev = pdev;
 
 	pr_info("AMD Geode RNG detected\n");
 	err = hwrng_register(&geode_rng);
@@ -116,20 +132,26 @@
 		       err);
 		goto err_unmap;
 	}
-out:
 	return err;
 
 err_unmap:
 	iounmap(mem);
-	goto out;
+free_priv:
+	kfree(priv);
+put_dev:
+	pci_dev_put(pdev);
+	return err;
 }
 
 static void __exit geode_rng_exit(void)
 {
-	void __iomem *mem = (void __iomem *)geode_rng.priv;
+	struct amd_geode_priv *priv;
 
+	priv = (struct amd_geode_priv *)geode_rng.priv;
 	hwrng_unregister(&geode_rng);
-	iounmap(mem);
+	iounmap(priv->membase);
+	pci_dev_put(priv->pcidev);
+	kfree(priv);
 }
 
 module_init(geode_rng_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/imx-rngc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/imx-rngc.c
@@ -110,7 +110,7 @@
 	cmd = readl(rngc->base + RNGC_COMMAND);
 	writel(cmd | RNGC_CMD_SELF_TEST, rngc->base + RNGC_COMMAND);
 
-	ret = wait_for_completion_timeout(&rngc->rng_op_done, RNGC_TIMEOUT);
+	ret = wait_for_completion_timeout(&rngc->rng_op_done, msecs_to_jiffies(RNGC_TIMEOUT));
 	imx_rngc_irq_mask_clear(rngc);
 	if (!ret)
 		return -ETIMEDOUT;
@@ -187,9 +187,7 @@
 		cmd = readl(rngc->base + RNGC_COMMAND);
 		writel(cmd | RNGC_CMD_SEED, rngc->base + RNGC_COMMAND);
 
-		ret = wait_for_completion_timeout(&rngc->rng_op_done,
-				RNGC_TIMEOUT);
-
+		ret = wait_for_completion_timeout(&rngc->rng_op_done, msecs_to_jiffies(RNGC_TIMEOUT));
 		if (!ret) {
 			ret = -ETIMEDOUT;
 			goto err;
@@ -270,13 +268,6 @@
 		goto err;
 	}
 
-	ret = devm_request_irq(&pdev->dev,
-			irq, imx_rngc_irq, 0, pdev->name, (void *)rngc);
-	if (ret) {
-		dev_err(rngc->dev, "Can't get interrupt working.\n");
-		goto err;
-	}
-
 	init_completion(&rngc->rng_op_done);
 
 	rngc->rng.name = pdev->name;
@@ -290,6 +281,13 @@
 
 	imx_rngc_irq_mask_clear(rngc);
 
+	ret = devm_request_irq(&pdev->dev,
+			irq, imx_rngc_irq, 0, pdev->name, (void *)rngc);
+	if (ret) {
+		dev_err(rngc->dev, "Can't get interrupt working.\n");
+		return ret;
+	}
+
 	if (self_test) {
 		ret = imx_rngc_self_test(rngc);
 		if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/iproc-rng200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/iproc-rng200.c
@@ -189,6 +189,8 @@
 		return PTR_ERR(priv->base);
 	}
 
+	dev_set_drvdata(dev, priv);
+
 	priv->rng.name = "iproc-rng200";
 	priv->rng.read = iproc_rng200_read;
 	priv->rng.init = iproc_rng200_init;
@@ -206,6 +208,28 @@
 	return 0;
 }
 
+static int __maybe_unused iproc_rng200_suspend(struct device *dev)
+{
+	struct iproc_rng200_dev *priv = dev_get_drvdata(dev);
+
+	iproc_rng200_cleanup(&priv->rng);
+
+	return 0;
+}
+
+static int __maybe_unused iproc_rng200_resume(struct device *dev)
+{
+	struct iproc_rng200_dev *priv =  dev_get_drvdata(dev);
+
+	iproc_rng200_init(&priv->rng);
+
+	return 0;
+}
+
+static const struct dev_pm_ops iproc_rng200_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(iproc_rng200_suspend, iproc_rng200_resume)
+};
+
 static const struct of_device_id iproc_rng200_of_match[] = {
 	{ .compatible = "brcm,bcm2711-rng200", },
 	{ .compatible = "brcm,bcm7211-rng200", },
@@ -219,6 +243,7 @@
 	.driver = {
 		.name		= "iproc-rng200",
 		.of_match_table = iproc_rng200_of_match,
+		.pm		= &iproc_rng200_pm_ops,
 	},
 	.probe		= iproc_rng200_probe,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/mtk-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/mtk-rng.c
@@ -142,7 +142,7 @@
 	dev_set_drvdata(&pdev->dev, priv);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, RNG_AUTOSUSPEND_TIMEOUT);
 	pm_runtime_use_autosuspend(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
+	devm_pm_runtime_enable(&pdev->dev);
 
 	dev_info(&pdev->dev, "registered RNG driver\n");
 
@@ -166,8 +166,13 @@
 	return mtk_rng_init(&priv->rng);
 }
 
-static UNIVERSAL_DEV_PM_OPS(mtk_rng_pm_ops, mtk_rng_runtime_suspend,
-			    mtk_rng_runtime_resume, NULL);
+static const struct dev_pm_ops mtk_rng_pm_ops = {
+	SET_RUNTIME_PM_OPS(mtk_rng_runtime_suspend,
+			   mtk_rng_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+};
+
 #define MTK_RNG_PM_OPS (&mtk_rng_pm_ops)
 #else	/* CONFIG_PM */
 #define MTK_RNG_PM_OPS NULL
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/nomadik-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/nomadik-rng.c
@@ -13,8 +13,6 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 
-static struct clk *rng_clk;
-
 static int nmk_rng_read(struct hwrng *rng, void *data, size_t max, bool wait)
 {
 	void __iomem *base = (void __iomem *)rng->priv;
@@ -36,21 +34,20 @@
 
 static int nmk_rng_probe(struct amba_device *dev, const struct amba_id *id)
 {
+	struct clk *rng_clk;
 	void __iomem *base;
 	int ret;
 
-	rng_clk = devm_clk_get(&dev->dev, NULL);
+	rng_clk = devm_clk_get_enabled(&dev->dev, NULL);
 	if (IS_ERR(rng_clk)) {
 		dev_err(&dev->dev, "could not get rng clock\n");
 		ret = PTR_ERR(rng_clk);
 		return ret;
 	}
 
-	clk_prepare_enable(rng_clk);
-
 	ret = amba_request_regions(dev, dev->dev.init_name);
 	if (ret)
-		goto out_clk;
+		return ret;
 	ret = -ENOMEM;
 	base = devm_ioremap(&dev->dev, dev->res.start,
 			    resource_size(&dev->res));
@@ -64,15 +61,12 @@
 
 out_release:
 	amba_release_regions(dev);
-out_clk:
-	clk_disable(rng_clk);
 	return ret;
 }
 
 static void nmk_rng_remove(struct amba_device *dev)
 {
 	amba_release_regions(dev);
-	clk_disable(rng_clk);
 }
 
 static const struct amba_id nmk_rng_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/omap3-rom-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/omap3-rom-rng.c
@@ -92,7 +92,7 @@
 
 	r = ddata->rom_rng_call(0, 0, RNG_GEN_PRNG_HW_INIT);
 	if (r != 0) {
-		clk_disable(ddata->clk);
+		clk_disable_unprepare(ddata->clk);
 		dev_err(dev, "HW init failed: %d\n", r);
 
 		return -EIO;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/pic32-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/pic32-rng.c
@@ -36,7 +36,6 @@
 struct pic32_rng {
 	void __iomem	*base;
 	struct hwrng	rng;
-	struct clk	*clk;
 };
 
 /*
@@ -70,6 +69,7 @@
 static int pic32_rng_probe(struct platform_device *pdev)
 {
 	struct pic32_rng *priv;
+	struct clk *clk;
 	u32 v;
 	int ret;
 
@@ -81,13 +81,9 @@
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-	priv->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(priv->clk))
-		return PTR_ERR(priv->clk);
-
-	ret = clk_prepare_enable(priv->clk);
-	if (ret)
-		return ret;
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
 
 	/* enable TRNG in enhanced mode */
 	v = TRNGEN | TRNGMOD;
@@ -98,15 +94,11 @@
 
 	ret = devm_hwrng_register(&pdev->dev, &priv->rng);
 	if (ret)
-		goto err_register;
+		return ret;
 
 	platform_set_drvdata(pdev, priv);
 
 	return 0;
-
-err_register:
-	clk_disable_unprepare(priv->clk);
-	return ret;
 }
 
 static int pic32_rng_remove(struct platform_device *pdev)
@@ -114,7 +106,6 @@
 	struct pic32_rng *rng = platform_get_drvdata(pdev);
 
 	writel(0, rng->base + RNGCON);
-	clk_disable_unprepare(rng->clk);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/st-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/st-rng.c
@@ -42,7 +42,6 @@
 
 struct st_rng_data {
 	void __iomem	*base;
-	struct clk	*clk;
 	struct hwrng	ops;
 };
 
@@ -85,26 +84,18 @@
 	if (IS_ERR(base))
 		return PTR_ERR(base);
 
-	clk = devm_clk_get(&pdev->dev, NULL);
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
 
-	ret = clk_prepare_enable(clk);
-	if (ret)
-		return ret;
-
 	ddata->ops.priv	= (unsigned long)ddata;
 	ddata->ops.read	= st_rng_read;
 	ddata->ops.name	= pdev->name;
 	ddata->base	= base;
-	ddata->clk	= clk;
-
-	dev_set_drvdata(&pdev->dev, ddata);
 
 	ret = devm_hwrng_register(&pdev->dev, &ddata->ops);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to register HW RNG\n");
-		clk_disable_unprepare(clk);
 		return ret;
 	}
 
@@ -113,15 +104,6 @@
 	return 0;
 }
 
-static int st_rng_remove(struct platform_device *pdev)
-{
-	struct st_rng_data *ddata = dev_get_drvdata(&pdev->dev);
-
-	clk_disable_unprepare(ddata->clk);
-
-	return 0;
-}
-
 static const struct of_device_id st_rng_match[] __maybe_unused = {
 	{ .compatible = "st,rng" },
 	{},
@@ -134,7 +116,6 @@
 		.of_match_table = of_match_ptr(st_rng_match),
 	},
 	.probe = st_rng_probe,
-	.remove = st_rng_remove
 };
 
 module_platform_driver(st_rng_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/hw_random/virtio-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/hw_random/virtio-rng.c
@@ -4,6 +4,7 @@
  *  Copyright (C) 2007, 2008 Rusty Russell IBM Corporation
  */
 
+#include <asm/barrier.h>
 #include <linux/err.h>
 #include <linux/hw_random.h>
 #include <linux/scatterlist.h>
@@ -18,71 +19,111 @@
 struct virtrng_info {
 	struct hwrng hwrng;
 	struct virtqueue *vq;
-	struct completion have_data;
 	char name[25];
-	unsigned int data_avail;
 	int index;
-	bool busy;
 	bool hwrng_register_done;
 	bool hwrng_removed;
+	/* data transfer */
+	struct completion have_data;
+	unsigned int data_avail;
+	unsigned int data_idx;
+	/* minimal size returned by rng_buffer_size() */
+#if SMP_CACHE_BYTES < 32
+	u8 data[32];
+#else
+	u8 data[SMP_CACHE_BYTES];
+#endif
 };
 
 static void random_recv_done(struct virtqueue *vq)
 {
 	struct virtrng_info *vi = vq->vdev->priv;
+	unsigned int len;
 
 	/* We can get spurious callbacks, e.g. shared IRQs + virtio_pci. */
-	if (!virtqueue_get_buf(vi->vq, &vi->data_avail))
+	if (!virtqueue_get_buf(vi->vq, &len))
 		return;
 
+	smp_store_release(&vi->data_avail, len);
 	complete(&vi->have_data);
 }
 
-/* The host will fill any buffer we give it with sweet, sweet randomness. */
-static void register_buffer(struct virtrng_info *vi, u8 *buf, size_t size)
+static void request_entropy(struct virtrng_info *vi)
 {
 	struct scatterlist sg;
 
-	sg_init_one(&sg, buf, size);
+	reinit_completion(&vi->have_data);
+	vi->data_idx = 0;
+
+	sg_init_one(&sg, vi->data, sizeof(vi->data));
 
 	/* There should always be room for one buffer. */
-	virtqueue_add_inbuf(vi->vq, &sg, 1, buf, GFP_KERNEL);
+	virtqueue_add_inbuf(vi->vq, &sg, 1, vi->data, GFP_KERNEL);
 
 	virtqueue_kick(vi->vq);
 }
 
+static unsigned int copy_data(struct virtrng_info *vi, void *buf,
+			      unsigned int size)
+{
+	size = min_t(unsigned int, size, vi->data_avail);
+	memcpy(buf, vi->data + vi->data_idx, size);
+	vi->data_idx += size;
+	vi->data_avail -= size;
+	if (vi->data_avail == 0)
+		request_entropy(vi);
+	return size;
+}
+
 static int virtio_read(struct hwrng *rng, void *buf, size_t size, bool wait)
 {
 	int ret;
 	struct virtrng_info *vi = (struct virtrng_info *)rng->priv;
+	unsigned int chunk;
+	size_t read;
 
 	if (vi->hwrng_removed)
 		return -ENODEV;
 
-	if (!vi->busy) {
-		vi->busy = true;
-		reinit_completion(&vi->have_data);
-		register_buffer(vi, buf, size);
+	read = 0;
+
+	/* copy available data */
+	if (smp_load_acquire(&vi->data_avail)) {
+		chunk = copy_data(vi, buf, size);
+		size -= chunk;
+		read += chunk;
 	}
 
 	if (!wait)
-		return 0;
-
-	ret = wait_for_completion_killable(&vi->have_data);
-	if (ret < 0)
-		return ret;
+		return read;
 
-	vi->busy = false;
+	/* We have already copied available entropy,
+	 * so either size is 0 or data_avail is 0
+	 */
+	while (size != 0) {
+		/* data_avail is 0 but a request is pending */
+		ret = wait_for_completion_killable(&vi->have_data);
+		if (ret < 0)
+			return ret;
+		/* if vi->data_avail is 0, we have been interrupted
+		 * by a cleanup, but buffer stays in the queue
+		 */
+		if (vi->data_avail == 0)
+			return read;
+
+		chunk = copy_data(vi, buf + read, size);
+		size -= chunk;
+		read += chunk;
+	}
 
-	return vi->data_avail;
+	return read;
 }
 
 static void virtio_cleanup(struct hwrng *rng)
 {
 	struct virtrng_info *vi = (struct virtrng_info *)rng->priv;
 
-	if (vi->busy)
-		wait_for_completion(&vi->have_data);
+	complete(&vi->have_data);
 }
 
 static int probe_common(struct virtio_device *vdev)
@@ -118,6 +159,9 @@
 		goto err_find;
 	}
 
+	/* we always have a pending entropy request */
+	request_entropy(vi);
+
 	return 0;
 
 err_find:
@@ -133,9 +177,9 @@
 
 	vi->hwrng_removed = true;
 	vi->data_avail = 0;
+	vi->data_idx = 0;
 	complete(&vi->have_data);
 	vdev->config->reset(vdev);
-	vi->busy = false;
 	if (vi->hwrng_register_done)
 		hwrng_unregister(&vi->hwrng);
 	vdev->config->del_vqs(vdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/Kconfig
@@ -153,7 +153,8 @@
 
 config ASPEED_BT_IPMI_BMC
 	depends on ARCH_ASPEED || COMPILE_TEST
-	depends on REGMAP && REGMAP_MMIO && MFD_SYSCON
+	depends on MFD_SYSCON
+	select REGMAP_MMIO
 	tristate "BT IPMI bmc driver"
 	help
 	  Provides a driver for the BT (Block Transfer) IPMI interface
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/ipmb_dev_int.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/ipmb_dev_int.c
@@ -322,6 +322,9 @@
 	ipmb_dev->miscdev.name = devm_kasprintf(&client->dev, GFP_KERNEL,
 						"%s%d", "ipmb-",
 						client->adapter->nr);
+	if (!ipmb_dev->miscdev.name)
+		return -ENOMEM;
+
 	ipmb_dev->miscdev.fops = &ipmb_fops;
 	ipmb_dev->miscdev.parent = &client->dev;
 	ret = misc_register(&ipmb_dev->miscdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/ipmi_msghandler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/ipmi_msghandler.c
@@ -11,8 +11,8 @@
  * Copyright 2002 MontaVista Software Inc.
  */
 
-#define pr_fmt(fmt) "%s" fmt, "IPMI message handler: "
-#define dev_fmt pr_fmt
+#define pr_fmt(fmt) "IPMI message handler: " fmt
+#define dev_fmt(fmt) pr_fmt(fmt)
 
 #include <linux/module.h>
 #include <linux/errno.h>
@@ -191,6 +191,8 @@
 	struct work_struct remove_work;
 };
 
+static struct workqueue_struct *remove_work_wq;
+
 static struct ipmi_user *acquire_ipmi_user(struct ipmi_user *user, int *index)
 	__acquires(user->release_barrier)
 {
@@ -1261,7 +1263,7 @@
 	struct ipmi_user *user = container_of(ref, struct ipmi_user, refcount);
 
 	/* SRCU cleanup must happen in task context. */
-	schedule_work(&user->remove_work);
+	queue_work(remove_work_wq, &user->remove_work);
 }
 
 static void _ipmi_destroy_user(struct ipmi_user *user)
@@ -1271,6 +1273,7 @@
 	unsigned long    flags;
 	struct cmd_rcvr  *rcvr;
 	struct cmd_rcvr  *rcvrs = NULL;
+	struct module    *owner;
 
 	if (!acquire_ipmi_user(user, &i)) {
 		/*
@@ -1332,8 +1335,9 @@
 		kfree(rcvr);
 	}
 
+	owner = intf->owner;
 	kref_put(&intf->refcount, intf_free);
-	module_put(intf->owner);
+	module_put(owner);
 }
 
 int ipmi_destroy_user(struct ipmi_user *user)
@@ -2930,7 +2934,7 @@
 	 * with removing the device attributes while reading a device
 	 * attribute.
 	 */
-	schedule_work(&bmc->remove_work);
+	queue_work(remove_work_wq, &bmc->remove_work);
 }
 
 /*
@@ -3525,12 +3529,16 @@
 				     struct ipmi_smi_msg *msg,
 				     unsigned char err)
 {
+	int rv;
 	msg->rsp[0] = msg->data[0] | 4;
 	msg->rsp[1] = msg->data[1];
 	msg->rsp[2] = err;
 	msg->rsp_size = 3;
-	/* It's an error, so it will never requeue, no need to check return. */
-	handle_one_recv_msg(intf, msg);
+
+	/* This will never requeue, but it may ask us to free the message. */
+	rv = handle_one_recv_msg(intf, msg);
+	if (rv == 0)
+		ipmi_free_smi_msg(msg);
 }
 
 static void cleanup_smi_msgs(struct ipmi_smi *intf)
@@ -4789,7 +4797,9 @@
 static void free_smi_msg(struct ipmi_smi_msg *msg)
 {
 	atomic_dec(&smi_msg_inuse_count);
-	kfree(msg);
+	/* Try to keep as much stuff out of the panic path as possible. */
+	if (!oops_in_progress)
+		kfree(msg);
 }
 
 struct ipmi_smi_msg *ipmi_alloc_smi_msg(void)
@@ -4808,7 +4818,9 @@
 static void free_recv_msg(struct ipmi_recv_msg *msg)
 {
 	atomic_dec(&recv_msg_inuse_count);
-	kfree(msg);
+	/* Try to keep as much stuff out of the panic path as possible. */
+	if (!oops_in_progress)
+		kfree(msg);
 }
 
 static struct ipmi_recv_msg *ipmi_alloc_recv_msg(void)
@@ -4826,7 +4838,7 @@
 
 void ipmi_free_recv_msg(struct ipmi_recv_msg *msg)
 {
-	if (msg->user)
+	if (msg->user && !oops_in_progress)
 		kref_put(&msg->user->refcount, free_user);
 	msg->done(msg);
 }
@@ -5142,7 +5154,16 @@
 	if (initialized)
 		goto out;
 
-	init_srcu_struct(&ipmi_interfaces_srcu);
+	rv = init_srcu_struct(&ipmi_interfaces_srcu);
+	if (rv)
+		goto out;
+
+	remove_work_wq = create_singlethread_workqueue("ipmi-msghandler-remove-wq");
+	if (!remove_work_wq) {
+		pr_err("unable to create ipmi-msghandler-remove-wq workqueue");
+		rv = -ENOMEM;
+		goto out_wq;
+	}
 
 	timer_setup(&ipmi_timer, ipmi_timeout, 0);
 	mod_timer(&ipmi_timer, jiffies + IPMI_TIMEOUT_JIFFIES);
@@ -5151,6 +5172,9 @@
 
 	initialized = true;
 
+out_wq:
+	if (rv)
+		cleanup_srcu_struct(&ipmi_interfaces_srcu);
 out:
 	mutex_unlock(&ipmi_interfaces_mutex);
 	return rv;
@@ -5174,6 +5198,8 @@
 	int count;
 
 	if (initialized) {
+		destroy_workqueue(remove_work_wq);
+
 		atomic_notifier_chain_unregister(&panic_notifier_list,
 						 &panic_block);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/ipmi_si_intf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/ipmi_si_intf.c
@@ -2081,6 +2081,11 @@
 		new_smi->io.io_cleanup = NULL;
 	}
 
+	if (rv && new_smi->si_sm) {
+		kfree(new_smi->si_sm);
+		new_smi->si_sm = NULL;
+	}
+
 	return rv;
 }
 
@@ -2152,6 +2157,20 @@
 }
 module_init(init_ipmi_si);
 
+static void wait_msg_processed(struct smi_info *smi_info)
+{
+	unsigned long jiffies_now;
+	long time_diff;
+
+	while (smi_info->curr_msg || (smi_info->si_state != SI_NORMAL)) {
+		jiffies_now = jiffies;
+		time_diff = (((long)jiffies_now - (long)smi_info->last_timeout_jiffies)
+		     * SI_USEC_PER_JIFFY);
+		smi_event_handler(smi_info, time_diff);
+		schedule_timeout_uninterruptible(1);
+	}
+}
+
 static void shutdown_smi(void *send_info)
 {
 	struct smi_info *smi_info = send_info;
@@ -2186,16 +2205,13 @@
 	 * in the BMC.  Note that timers and CPU interrupts are off,
 	 * so no need for locks.
 	 */
-	while (smi_info->curr_msg || (smi_info->si_state != SI_NORMAL)) {
-		poll(smi_info);
-		schedule_timeout_uninterruptible(1);
-	}
+	wait_msg_processed(smi_info);
+
 	if (smi_info->handlers)
 		disable_si_irq(smi_info);
-	while (smi_info->curr_msg || (smi_info->si_state != SI_NORMAL)) {
-		poll(smi_info);
-		schedule_timeout_uninterruptible(1);
-	}
+
+	wait_msg_processed(smi_info);
+
 	if (smi_info->handlers)
 		smi_info->handlers->cleanup(smi_info->si_sm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/ipmi_ssif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/ipmi_ssif.c
@@ -74,7 +74,8 @@
 /*
  * Timer values
  */
-#define SSIF_MSG_USEC		20000	/* 20ms between message tries. */
+#define SSIF_MSG_USEC		60000	/* 60ms between message tries (T3). */
+#define SSIF_REQ_RETRY_USEC	60000	/* 60ms between send retries (T6). */
 #define SSIF_MSG_PART_USEC	5000	/* 5ms for a message part */
 
 /* How many times to we retry sending/receiving the message. */
@@ -82,7 +83,9 @@
 #define	SSIF_RECV_RETRIES	250
 
 #define SSIF_MSG_MSEC		(SSIF_MSG_USEC / 1000)
+#define SSIF_REQ_RETRY_MSEC	(SSIF_REQ_RETRY_USEC / 1000)
 #define SSIF_MSG_JIFFIES	((SSIF_MSG_USEC * 1000) / TICK_NSEC)
+#define SSIF_REQ_RETRY_JIFFIES	((SSIF_REQ_RETRY_USEC * 1000) / TICK_NSEC)
 #define SSIF_MSG_PART_JIFFIES	((SSIF_MSG_PART_USEC * 1000) / TICK_NSEC)
 
 /*
@@ -92,7 +95,7 @@
 #define SSIF_WATCH_WATCHDOG_TIMEOUT	msecs_to_jiffies(250)
 
 enum ssif_intf_state {
-	SSIF_NORMAL,
+	SSIF_IDLE,
 	SSIF_GETTING_FLAGS,
 	SSIF_GETTING_EVENTS,
 	SSIF_CLEARING_FLAGS,
@@ -100,8 +103,8 @@
 	/* FIXME - add watchdog stuff. */
 };
 
-#define SSIF_IDLE(ssif)	 ((ssif)->ssif_state == SSIF_NORMAL \
-			  && (ssif)->curr_msg == NULL)
+#define IS_SSIF_IDLE(ssif) ((ssif)->ssif_state == SSIF_IDLE \
+			    && (ssif)->curr_msg == NULL)
 
 /*
  * Indexes into stats[] in ssif_info below.
@@ -229,6 +232,9 @@
 	bool		    got_alert;
 	bool		    waiting_alert;
 
+	/* Used to inform the timeout that it should do a resend. */
+	bool		    do_resend;
+
 	/*
 	 * If set to true, this will request events the next time the
 	 * state machine is idle.
@@ -348,9 +354,9 @@
 
 /*
  * Must be called with the message lock held.  This will release the
- * message lock.  Note that the caller will check SSIF_IDLE and start a
- * new operation, so there is no need to check for new messages to
- * start in here.
+ * message lock.  Note that the caller will check IS_SSIF_IDLE and
+ * start a new operation, so there is no need to check for new
+ * messages to start in here.
  */
 static void start_clear_flags(struct ssif_info *ssif_info, unsigned long *flags)
 {
@@ -367,7 +373,7 @@
 
 	if (start_send(ssif_info, msg, 3) != 0) {
 		/* Error, just go to normal state. */
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 	}
 }
 
@@ -382,7 +388,7 @@
 	mb[0] = (IPMI_NETFN_APP_REQUEST << 2);
 	mb[1] = IPMI_GET_MSG_FLAGS_CMD;
 	if (start_send(ssif_info, mb, 2) != 0)
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 }
 
 static void check_start_send(struct ssif_info *ssif_info, unsigned long *flags,
@@ -393,7 +399,7 @@
 
 		flags = ipmi_ssif_lock_cond(ssif_info, &oflags);
 		ssif_info->curr_msg = NULL;
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 		ipmi_free_smi_msg(msg);
 	}
@@ -407,7 +413,7 @@
 
 	msg = ipmi_alloc_smi_msg();
 	if (!msg) {
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 		return;
 	}
@@ -430,7 +436,7 @@
 
 	msg = ipmi_alloc_smi_msg();
 	if (!msg) {
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 		return;
 	}
@@ -448,9 +454,9 @@
 
 /*
  * Must be called with the message lock held.  This will release the
- * message lock.  Note that the caller will check SSIF_IDLE and start a
- * new operation, so there is no need to check for new messages to
- * start in here.
+ * message lock.  Note that the caller will check IS_SSIF_IDLE and
+ * start a new operation, so there is no need to check for new
+ * messages to start in here.
  */
 static void handle_flags(struct ssif_info *ssif_info, unsigned long *flags)
 {
@@ -466,7 +472,7 @@
 		/* Events available. */
 		start_event_fetch(ssif_info, flags);
 	else {
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 	}
 }
@@ -538,22 +544,30 @@
 		  ssif_info->recv, I2C_SMBUS_BLOCK_DATA);
 }
 
+static void start_resend(struct ssif_info *ssif_info);
+
 static void retry_timeout(struct timer_list *t)
 {
 	struct ssif_info *ssif_info = from_timer(ssif_info, t, retry_timer);
 	unsigned long oflags, *flags;
-	bool waiting;
+	bool waiting, resend;
 
 	if (ssif_info->stopping)
 		return;
 
 	flags = ipmi_ssif_lock_cond(ssif_info, &oflags);
+	resend = ssif_info->do_resend;
+	ssif_info->do_resend = false;
 	waiting = ssif_info->waiting_alert;
 	ssif_info->waiting_alert = false;
 	ipmi_ssif_unlock_cond(ssif_info, flags);
 
 	if (waiting)
 		start_get(ssif_info);
+	if (resend) {
+		start_resend(ssif_info);
+		ssif_inc_stat(ssif_info, send_retries);
+	}
 }
 
 static void watch_timeout(struct timer_list *t)
@@ -568,7 +582,7 @@
 	if (ssif_info->watch_timeout) {
 		mod_timer(&ssif_info->watch_timer,
 			  jiffies + ssif_info->watch_timeout);
-		if (SSIF_IDLE(ssif_info)) {
+		if (IS_SSIF_IDLE(ssif_info)) {
 			start_flag_fetch(ssif_info, flags); /* Releases lock */
 			return;
 		}
@@ -602,8 +616,6 @@
 		start_get(ssif_info);
 }
 
-static int start_resend(struct ssif_info *ssif_info);
-
 static void msg_done_handler(struct ssif_info *ssif_info, int result,
 			     unsigned char *data, unsigned int len)
 {
@@ -756,7 +768,7 @@
 	}
 
 	switch (ssif_info->ssif_state) {
-	case SSIF_NORMAL:
+	case SSIF_IDLE:
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 		if (!msg)
 			break;
@@ -774,7 +786,7 @@
 			 * Error fetching flags, or invalid length,
 			 * just give up for now.
 			 */
-			ssif_info->ssif_state = SSIF_NORMAL;
+			ssif_info->ssif_state = SSIF_IDLE;
 			ipmi_ssif_unlock_cond(ssif_info, flags);
 			dev_warn(&ssif_info->client->dev,
 				 "Error getting flags: %d %d, %x\n",
@@ -782,9 +794,9 @@
 		} else if (data[0] != (IPMI_NETFN_APP_REQUEST | 1) << 2
 			   || data[1] != IPMI_GET_MSG_FLAGS_CMD) {
 			/*
-			 * Don't abort here, maybe it was a queued
-			 * response to a previous command.
+			 * Recv error response, give up.
 			 */
+			ssif_info->ssif_state = SSIF_IDLE;
 			ipmi_ssif_unlock_cond(ssif_info, flags);
 			dev_warn(&ssif_info->client->dev,
 				 "Invalid response getting flags: %x %x\n",
@@ -809,11 +821,19 @@
 				 "Invalid response clearing flags: %x %x\n",
 				 data[0], data[1]);
 		}
-		ssif_info->ssif_state = SSIF_NORMAL;
+		ssif_info->ssif_state = SSIF_IDLE;
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 		break;
 
 	case SSIF_GETTING_EVENTS:
+		if (!msg) {
+			/* Should never happen, but just in case. */
+			dev_warn(&ssif_info->client->dev,
+				 "No message set while getting events\n");
+			ipmi_ssif_unlock_cond(ssif_info, flags);
+			break;
+		}
+
 		if ((result < 0) || (len < 3) || (msg->rsp[2] != 0)) {
 			/* Error getting event, probably done. */
 			msg->done(msg);
@@ -838,6 +858,14 @@
 		break;
 
 	case SSIF_GETTING_MESSAGES:
+		if (!msg) {
+			/* Should never happen, but just in case. */
+			dev_warn(&ssif_info->client->dev,
+				 "No message set while getting messages\n");
+			ipmi_ssif_unlock_cond(ssif_info, flags);
+			break;
+		}
+
 		if ((result < 0) || (len < 3) || (msg->rsp[2] != 0)) {
 			/* Error getting event, probably done. */
 			msg->done(msg);
@@ -861,10 +889,17 @@
 			deliver_recv_msg(ssif_info, msg);
 		}
 		break;
+
+	default:
+		/* Should never happen, but just in case. */
+		dev_warn(&ssif_info->client->dev,
+			 "Invalid state in message done handling: %d\n",
+			 ssif_info->ssif_state);
+		ipmi_ssif_unlock_cond(ssif_info, flags);
 	}
 
 	flags = ipmi_ssif_lock_cond(ssif_info, &oflags);
-	if (SSIF_IDLE(ssif_info) && !ssif_info->stopping) {
+	if (IS_SSIF_IDLE(ssif_info) && !ssif_info->stopping) {
 		if (ssif_info->req_events)
 			start_event_fetch(ssif_info, flags);
 		else if (ssif_info->req_flags)
@@ -886,31 +921,23 @@
 	if (result < 0) {
 		ssif_info->retries_left--;
 		if (ssif_info->retries_left > 0) {
-			if (!start_resend(ssif_info)) {
-				ssif_inc_stat(ssif_info, send_retries);
-				return;
-			}
-			/* request failed, just return the error. */
-			ssif_inc_stat(ssif_info, send_errors);
-
-			if (ssif_info->ssif_debug & SSIF_DEBUG_MSG)
-				dev_dbg(&ssif_info->client->dev,
-					"%s: Out of retries\n", __func__);
-			msg_done_handler(ssif_info, -EIO, NULL, 0);
+			/*
+			 * Wait the retry timeout time per the spec,
+			 * then redo the send.
+			 */
+			ssif_info->do_resend = true;
+			mod_timer(&ssif_info->retry_timer,
+				  jiffies + SSIF_REQ_RETRY_JIFFIES);
 			return;
 		}
 
 		ssif_inc_stat(ssif_info, send_errors);
 
-		/*
-		 * Got an error on transmit, let the done routine
-		 * handle it.
-		 */
 		if (ssif_info->ssif_debug & SSIF_DEBUG_MSG)
 			dev_dbg(&ssif_info->client->dev,
-				"%s: Error  %d\n", __func__, result);
+				"%s: Out of retries\n", __func__);
 
-		msg_done_handler(ssif_info, result, NULL, 0);
+		msg_done_handler(ssif_info, -EIO, NULL, 0);
 		return;
 	}
 
@@ -973,7 +1000,7 @@
 	}
 }
 
-static int start_resend(struct ssif_info *ssif_info)
+static void start_resend(struct ssif_info *ssif_info)
 {
 	int command;
 
@@ -998,7 +1025,6 @@
 
 	ssif_i2c_send(ssif_info, msg_written_handler, I2C_SMBUS_WRITE,
 		   command, ssif_info->data, I2C_SMBUS_BLOCK_DATA);
-	return 0;
 }
 
 static int start_send(struct ssif_info *ssif_info,
@@ -1013,7 +1039,8 @@
 	ssif_info->retries_left = SSIF_SEND_RETRIES;
 	memcpy(ssif_info->data + 1, data, len);
 	ssif_info->data_len = len;
-	return start_resend(ssif_info);
+	start_resend(ssif_info);
+	return 0;
 }
 
 /* Must be called with the message lock held. */
@@ -1023,7 +1050,7 @@
 	unsigned long oflags;
 
  restart:
-	if (!SSIF_IDLE(ssif_info)) {
+	if (!IS_SSIF_IDLE(ssif_info)) {
 		ipmi_ssif_unlock_cond(ssif_info, flags);
 		return;
 	}
@@ -1246,7 +1273,7 @@
 	dev_set_drvdata(&ssif_info->client->dev, NULL);
 
 	/* make sure the driver is not looking for flags any more. */
-	while (ssif_info->ssif_state != SSIF_NORMAL)
+	while (ssif_info->ssif_state != SSIF_IDLE)
 		schedule_timeout(1);
 
 	ssif_info->stopping = true;
@@ -1313,8 +1340,10 @@
 	ret = i2c_smbus_write_block_data(client, SSIF_IPMI_REQUEST, len, msg);
 	if (ret) {
 		retry_cnt--;
-		if (retry_cnt > 0)
+		if (retry_cnt > 0) {
+			msleep(SSIF_REQ_RETRY_MSEC);
 			goto retry1;
+		}
 		return -ENODEV;
 	}
 
@@ -1385,7 +1414,7 @@
 restart:
 	list_for_each_entry(info, &ssif_infos, link) {
 		if (info->binfo.addr == addr) {
-			if (info->addr_src == SI_SMBIOS)
+			if (info->addr_src == SI_SMBIOS && !info->adapter_name)
 				info->adapter_name = kstrdup(adapter_name,
 							     GFP_KERNEL);
 
@@ -1455,8 +1484,10 @@
 					 32, msg);
 	if (ret) {
 		retry_cnt--;
-		if (retry_cnt > 0)
+		if (retry_cnt > 0) {
+			msleep(SSIF_REQ_RETRY_MSEC);
 			goto retry_write;
+		}
 		dev_err(&client->dev, "Could not write multi-part start, though the BMC said it could handle it.  Just limit sends to one part.\n");
 		return ret;
 	}
@@ -1583,6 +1614,11 @@
 	info->addr_src = SI_ACPI;
 	info->client = client;
 	info->adapter_name = kstrdup(client->adapter->name, GFP_KERNEL);
+	if (!info->adapter_name) {
+		kfree(info);
+		return -ENOMEM;
+	}
+
 	info->binfo.addr = client->addr;
 	list_add_tail(&info->link, &ssif_infos);
 	return 0;
@@ -1659,6 +1695,9 @@
 		}
 	}
 
+	ssif_info->client = client;
+	i2c_set_clientdata(client, ssif_info);
+
 	rv = ssif_check_and_remove(client, ssif_info);
 	/* If rv is 0 and addr source is not SI_ACPI, continue probing */
 	if (!rv && ssif_info->addr_source == SI_ACPI) {
@@ -1679,9 +1718,6 @@
 		ipmi_addr_src_to_str(ssif_info->addr_source),
 		client->addr, client->adapter->name, slave_addr);
 
-	ssif_info->client = client;
-	i2c_set_clientdata(client, ssif_info);
-
 	/* Now check for system interface capabilities */
 	msg[0] = IPMI_NETFN_APP_REQUEST << 2;
 	msg[1] = IPMI_GET_SYSTEM_INTERFACE_CAPABILITIES_CMD;
@@ -1818,7 +1854,7 @@
 	}
 
 	spin_lock_init(&ssif_info->lock);
-	ssif_info->ssif_state = SSIF_NORMAL;
+	ssif_info->ssif_state = SSIF_IDLE;
 	timer_setup(&ssif_info->retry_timer, retry_timeout, 0);
 	timer_setup(&ssif_info->watch_timer, watch_timeout, 0);
 
@@ -1881,6 +1917,7 @@
 
 		dev_err(&ssif_info->client->dev,
 			"Unable to start IPMI SSIF: %d\n", rv);
+		i2c_set_clientdata(client, NULL);
 		kfree(ssif_info);
 	}
 	kfree(resp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/ipmi_watchdog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/ipmi_watchdog.c
@@ -342,13 +342,17 @@
 static DECLARE_COMPLETION(msg_wait);
 static void msg_free_smi(struct ipmi_smi_msg *msg)
 {
-	if (atomic_dec_and_test(&msg_tofree))
-		complete(&msg_wait);
+	if (atomic_dec_and_test(&msg_tofree)) {
+		if (!oops_in_progress)
+			complete(&msg_wait);
+	}
 }
 static void msg_free_recv(struct ipmi_recv_msg *msg)
 {
-	if (atomic_dec_and_test(&msg_tofree))
-		complete(&msg_wait);
+	if (atomic_dec_and_test(&msg_tofree)) {
+		if (!oops_in_progress)
+			complete(&msg_wait);
+	}
 }
 static struct ipmi_smi_msg smi_msg = {
 	.done = msg_free_smi
@@ -434,8 +438,10 @@
 	rv = __ipmi_set_timeout(&smi_msg,
 				&recv_msg,
 				&send_heartbeat_now);
-	if (rv)
+	if (rv) {
+		atomic_set(&msg_tofree, 0);
 		return rv;
+	}
 
 	wait_for_completion(&msg_wait);
 
@@ -497,7 +503,7 @@
 	msg.cmd = IPMI_WDOG_RESET_TIMER;
 	msg.data = NULL;
 	msg.data_len = 0;
-	atomic_inc(&panic_done_count);
+	atomic_add(2, &panic_done_count);
 	rv = ipmi_request_supply_msgs(watchdog_user,
 				      (struct ipmi_addr *) &addr,
 				      0,
@@ -507,7 +513,7 @@
 				      &panic_halt_heartbeat_recv_msg,
 				      1);
 	if (rv)
-		atomic_dec(&panic_done_count);
+		atomic_sub(2, &panic_done_count);
 }
 
 static struct ipmi_smi_msg panic_halt_smi_msg = {
@@ -531,12 +537,12 @@
 	/* Wait for the messages to be free. */
 	while (atomic_read(&panic_done_count) != 0)
 		ipmi_poll_interface(watchdog_user);
-	atomic_inc(&panic_done_count);
+	atomic_add(2, &panic_done_count);
 	rv = __ipmi_set_timeout(&panic_halt_smi_msg,
 				&panic_halt_recv_msg,
 				&send_heartbeat_now);
 	if (rv) {
-		atomic_dec(&panic_done_count);
+		atomic_sub(2, &panic_done_count);
 		pr_warn("Unable to extend the watchdog timeout\n");
 	} else {
 		if (send_heartbeat_now)
@@ -580,6 +586,7 @@
 				      &recv_msg,
 				      1);
 	if (rv) {
+		atomic_set(&msg_tofree, 0);
 		pr_warn("heartbeat send failure: %d\n", rv);
 		return rv;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/kcs_bmc_aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/kcs_bmc_aspeed.c
@@ -404,13 +404,31 @@
 static void aspeed_kcs_irq_mask_update(struct kcs_bmc_device *kcs_bmc, u8 mask, u8 state)
 {
 	struct aspeed_kcs_bmc *priv = to_aspeed_kcs_bmc(kcs_bmc);
+	int rc;
+	u8 str;
 
 	/* We don't have an OBE IRQ, emulate it */
 	if (mask & KCS_BMC_EVENT_TYPE_OBE) {
-		if (KCS_BMC_EVENT_TYPE_OBE & state)
-			mod_timer(&priv->obe.timer, jiffies + OBE_POLL_PERIOD);
-		else
+		if (KCS_BMC_EVENT_TYPE_OBE & state) {
+			/*
+			 * Given we don't have an OBE IRQ, delay by polling briefly to see if we can
+			 * observe such an event before returning to the caller. This is not
+			 * incorrect because OBF may have already become clear before enabling the
+			 * IRQ if we had one, under which circumstance no event will be propagated
+			 * anyway.
+			 *
+			 * The onus is on the client to perform a race-free check that it hasn't
+			 * missed the event.
+			 */
+			rc = read_poll_timeout_atomic(aspeed_kcs_inb, str,
+						      !(str & KCS_BMC_STR_OBF), 1, 100, false,
+						      &priv->kcs_bmc, priv->kcs_bmc.ioreg.str);
+			/* Time for the slow path? */
+			if (rc == -ETIMEDOUT)
+				mod_timer(&priv->obe.timer, jiffies + OBE_POLL_PERIOD);
+		} else {
 			del_timer(&priv->obe.timer);
+		}
 	}
 
 	if (mask & KCS_BMC_EVENT_TYPE_IBF) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ipmi/kcs_bmc_serio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ipmi/kcs_bmc_serio.c
@@ -73,10 +73,12 @@
 	struct serio *port;
 
 	priv = devm_kzalloc(kcs_bmc->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
 
 	/* Use kzalloc() as the allocation is cleaned up with kfree() via serio_unregister_port() */
 	port = kzalloc(sizeof(*port), GFP_KERNEL);
-	if (!(priv && port))
+	if (!port)
 		return -ENOMEM;
 
 	port->id.type = SERIO_8042;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/mem.c
@@ -702,8 +702,8 @@
 #endif
 	 [5] = { "zero", 0666, &zero_fops, 0 },
 	 [7] = { "full", 0666, &full_fops, 0 },
-	 [8] = { "random", 0666, &random_fops, 0 },
-	 [9] = { "urandom", 0666, &urandom_fops, 0 },
+	 [8] = { "random", 0666, &random_fops, FMODE_NOWAIT },
+	 [9] = { "urandom", 0666, &urandom_fops, FMODE_NOWAIT },
 #ifdef CONFIG_PRINTK
 	[11] = { "kmsg", 0644, &kmsg_fops, 0 },
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/mwave/3780i.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/mwave/3780i.h
@@ -68,7 +68,7 @@
 	unsigned char ClockControl:1;	/* RW: Clock control: 0=normal, 1=stop 3780i clocks */
 	unsigned char SoftReset:1;	/* RW: Soft reset 0=normal, 1=soft reset active */
 	unsigned char ConfigMode:1;	/* RW: Configuration mode, 0=normal, 1=config mode */
-	unsigned char Reserved:5;	/* 0: Reserved */
+	unsigned short Reserved:13;	/* 0: Reserved */
 } DSP_ISA_SLAVE_CONTROL;
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/pcmcia/cm4000_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/pcmcia/cm4000_cs.c
@@ -530,7 +530,8 @@
 			DEBUGP(5, dev, "NumRecBytes is valid\n");
 			break;
 		}
-		usleep_range(10000, 11000);
+		/* can not sleep as this is in atomic context */
+		mdelay(10);
 	}
 	if (i == 100) {
 		DEBUGP(5, dev, "Timeout waiting for NumRecBytes getting "
@@ -550,7 +551,8 @@
 			}
 			break;
 		}
-		usleep_range(10000, 11000);
+		/* can not sleep as this is in atomic context */
+		mdelay(10);
 	}
 
 	/* check whether it is a short PTS reply? */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/ppdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/ppdev.c
@@ -296,28 +296,35 @@
 	if (!port) {
 		pr_warn("%s: no associated port!\n", name);
 		rc = -ENXIO;
-		goto err;
+		goto err_free_name;
+	}
+
+	index = ida_alloc(&ida_index, GFP_KERNEL);
+	if (index < 0) {
+		pr_warn("%s: failed to get index!\n", name);
+		rc = index;
+		goto err_put_port;
 	}
 
-	index = ida_simple_get(&ida_index, 0, 0, GFP_KERNEL);
 	memset(&ppdev_cb, 0, sizeof(ppdev_cb));
 	ppdev_cb.irq_func = pp_irq;
 	ppdev_cb.flags = (pp->flags & PP_EXCL) ? PARPORT_FLAG_EXCL : 0;
 	ppdev_cb.private = pp;
 	pdev = parport_register_dev_model(port, name, &ppdev_cb, index);
-	parport_put_port(port);
 
 	if (!pdev) {
 		pr_warn("%s: failed to register device!\n", name);
 		rc = -ENXIO;
-		ida_simple_remove(&ida_index, index);
-		goto err;
+		ida_free(&ida_index, index);
+		goto err_put_port;
 	}
 
 	pp->pdev = pdev;
 	pp->index = index;
 	dev_dbg(&pdev->dev, "registered pardevice\n");
-err:
+err_put_port:
+	parport_put_port(port);
+err_free_name:
 	kfree(name);
 	return rc;
 }
@@ -750,7 +757,7 @@
 
 	if (pp->pdev) {
 		parport_unregister_device(pp->pdev);
-		ida_simple_remove(&ida_index, pp->index);
+		ida_free(&ida_index, pp->index);
 		pp->pdev = NULL;
 		pr_debug(CHRDEV "%x: unregistered pardevice\n", minor);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/random.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/random.c
@@ -1,310 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
 /*
- * random.c -- A strong random number generator
- *
- * Copyright (C) 2017 Jason A. Donenfeld <Jason@zx2c4.com>. All
- * Rights Reserved.
- *
+ * Copyright (C) 2017-2022 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
  * Copyright Matt Mackall <mpm@selenic.com>, 2003, 2004, 2005
+ * Copyright Theodore Ts'o, 1994, 1995, 1996, 1997, 1998, 1999. All rights reserved.
  *
- * Copyright Theodore Ts'o, 1994, 1995, 1996, 1997, 1998, 1999.  All
- * rights reserved.
+ * This driver produces cryptographically secure pseudorandom data. It is divided
+ * into roughly six sections, each with a section header:
  *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- *    notice, and the entire permission notice in its entirety,
- *    including the disclaimer of warranties.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in the
- *    documentation and/or other materials provided with the distribution.
- * 3. The name of the author may not be used to endorse or promote
- *    products derived from this software without specific prior
- *    written permission.
- *
- * ALTERNATIVELY, this product may be distributed under the terms of
- * the GNU General Public License, in which case the provisions of the GPL are
- * required INSTEAD OF the above restrictions.  (This clause is
- * necessary due to a potential bad interaction between the GPL and
- * the restrictions contained in a BSD-style copyright.)
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
- * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ALL OF
- * WHICH ARE HEREBY DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE
- * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
- * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
- * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
- * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
- * USE OF THIS SOFTWARE, EVEN IF NOT ADVISED OF THE POSSIBILITY OF SUCH
- * DAMAGE.
- */
-
-/*
- * (now, with legal B.S. out of the way.....)
- *
- * This routine gathers environmental noise from device drivers, etc.,
- * and returns good random numbers, suitable for cryptographic use.
- * Besides the obvious cryptographic uses, these numbers are also good
- * for seeding TCP sequence numbers, and other places where it is
- * desirable to have numbers which are not only random, but hard to
- * predict by an attacker.
- *
- * Theory of operation
- * ===================
- *
- * Computers are very predictable devices.  Hence it is extremely hard
- * to produce truly random numbers on a computer --- as opposed to
- * pseudo-random numbers, which can easily generated by using a
- * algorithm.  Unfortunately, it is very easy for attackers to guess
- * the sequence of pseudo-random number generators, and for some
- * applications this is not acceptable.  So instead, we must try to
- * gather "environmental noise" from the computer's environment, which
- * must be hard for outside attackers to observe, and use that to
- * generate random numbers.  In a Unix environment, this is best done
- * from inside the kernel.
- *
- * Sources of randomness from the environment include inter-keyboard
- * timings, inter-interrupt timings from some interrupts, and other
- * events which are both (a) non-deterministic and (b) hard for an
- * outside observer to measure.  Randomness from these sources are
- * added to an "entropy pool", which is mixed using a CRC-like function.
- * This is not cryptographically strong, but it is adequate assuming
- * the randomness is not chosen maliciously, and it is fast enough that
- * the overhead of doing it on every interrupt is very reasonable.
- * As random bytes are mixed into the entropy pool, the routines keep
- * an *estimate* of how many bits of randomness have been stored into
- * the random number generator's internal state.
- *
- * When random bytes are desired, they are obtained by taking the SHA
- * hash of the contents of the "entropy pool".  The SHA hash avoids
- * exposing the internal state of the entropy pool.  It is believed to
- * be computationally infeasible to derive any useful information
- * about the input of SHA from its output.  Even if it is possible to
- * analyze SHA in some clever way, as long as the amount of data
- * returned from the generator is less than the inherent entropy in
- * the pool, the output data is totally unpredictable.  For this
- * reason, the routine decreases its internal estimate of how many
- * bits of "true randomness" are contained in the entropy pool as it
- * outputs random numbers.
- *
- * If this estimate goes to zero, the routine can still generate
- * random numbers; however, an attacker may (at least in theory) be
- * able to infer the future output of the generator from prior
- * outputs.  This requires successful cryptanalysis of SHA, which is
- * not believed to be feasible, but there is a remote possibility.
- * Nonetheless, these numbers should be useful for the vast majority
- * of purposes.
- *
- * Exported interfaces ---- output
- * ===============================
- *
- * There are four exported interfaces; two for use within the kernel,
- * and two or use from userspace.
- *
- * Exported interfaces ---- userspace output
- * -----------------------------------------
- *
- * The userspace interfaces are two character devices /dev/random and
- * /dev/urandom.  /dev/random is suitable for use when very high
- * quality randomness is desired (for example, for key generation or
- * one-time pads), as it will only return a maximum of the number of
- * bits of randomness (as estimated by the random number generator)
- * contained in the entropy pool.
- *
- * The /dev/urandom device does not have this limit, and will return
- * as many bytes as are requested.  As more and more random bytes are
- * requested without giving time for the entropy pool to recharge,
- * this will result in random numbers that are merely cryptographically
- * strong.  For many applications, however, this is acceptable.
- *
- * Exported interfaces ---- kernel output
- * --------------------------------------
- *
- * The primary kernel interface is
- *
- * 	void get_random_bytes(void *buf, int nbytes);
- *
- * This interface will return the requested number of random bytes,
- * and place it in the requested buffer.  This is equivalent to a
- * read from /dev/urandom.
- *
- * For less critical applications, there are the functions:
- *
- * 	u32 get_random_u32()
- * 	u64 get_random_u64()
- * 	unsigned int get_random_int()
- * 	unsigned long get_random_long()
- *
- * These are produced by a cryptographic RNG seeded from get_random_bytes,
- * and so do not deplete the entropy pool as much.  These are recommended
- * for most in-kernel operations *if the result is going to be stored in
- * the kernel*.
- *
- * Specifically, the get_random_int() family do not attempt to do
- * "anti-backtracking".  If you capture the state of the kernel (e.g.
- * by snapshotting the VM), you can figure out previous get_random_int()
- * return values.  But if the value is stored in the kernel anyway,
- * this is not a problem.
- *
- * It *is* safe to expose get_random_int() output to attackers (e.g. as
- * network cookies); given outputs 1..n, it's not feasible to predict
- * outputs 0 or n+1.  The only concern is an attacker who breaks into
- * the kernel later; the get_random_int() engine is not reseeded as
- * often as the get_random_bytes() one.
- *
- * get_random_bytes() is needed for keys that need to stay secret after
- * they are erased from the kernel.  For example, any key that will
- * be wrapped and stored encrypted.  And session encryption keys: we'd
- * like to know that after the session is closed and the keys erased,
- * the plaintext is unrecoverable to someone who recorded the ciphertext.
- *
- * But for network ports/cookies, stack canaries, PRNG seeds, address
- * space layout randomization, session *authentication* keys, or other
- * applications where the sensitive data is stored in the kernel in
- * plaintext for as long as it's sensitive, the get_random_int() family
- * is just fine.
- *
- * Consider ASLR.  We want to keep the address space secret from an
- * outside attacker while the process is running, but once the address
- * space is torn down, it's of no use to an attacker any more.  And it's
- * stored in kernel data structures as long as it's alive, so worrying
- * about an attacker's ability to extrapolate it from the get_random_int()
- * CRNG is silly.
- *
- * Even some cryptographic keys are safe to generate with get_random_int().
- * In particular, keys for SipHash are generally fine.  Here, knowledge
- * of the key authorizes you to do something to a kernel object (inject
- * packets to a network connection, or flood a hash table), and the
- * key is stored with the object being protected.  Once it goes away,
- * we no longer care if anyone knows the key.
- *
- * prandom_u32()
- * -------------
- *
- * For even weaker applications, see the pseudorandom generator
- * prandom_u32(), prandom_max(), and prandom_bytes().  If the random
- * numbers aren't security-critical at all, these are *far* cheaper.
- * Useful for self-tests, random error simulation, randomized backoffs,
- * and any other application where you trust that nobody is trying to
- * maliciously mess with you by guessing the "random" numbers.
- *
- * Exported interfaces ---- input
- * ==============================
- *
- * The current exported interfaces for gathering environmental noise
- * from the devices are:
- *
- *	void add_device_randomness(const void *buf, unsigned int size);
- * 	void add_input_randomness(unsigned int type, unsigned int code,
- *                                unsigned int value);
- *	void add_interrupt_randomness(int irq, int irq_flags);
- * 	void add_disk_randomness(struct gendisk *disk);
- *
- * add_device_randomness() is for adding data to the random pool that
- * is likely to differ between two devices (or possibly even per boot).
- * This would be things like MAC addresses or serial numbers, or the
- * read-out of the RTC. This does *not* add any actual entropy to the
- * pool, but it initializes the pool to different values for devices
- * that might otherwise be identical and have very little entropy
- * available to them (particularly common in the embedded world).
- *
- * add_input_randomness() uses the input layer interrupt timing, as well as
- * the event type information from the hardware.
- *
- * add_interrupt_randomness() uses the interrupt timing as random
- * inputs to the entropy pool. Using the cycle counters and the irq source
- * as inputs, it feeds the randomness roughly once a second.
- *
- * add_disk_randomness() uses what amounts to the seek time of block
- * layer request events, on a per-disk_devt basis, as input to the
- * entropy pool. Note that high-speed solid state drives with very low
- * seek times do not make for good sources of entropy, as their seek
- * times are usually fairly consistent.
- *
- * All of these routines try to estimate how many bits of randomness a
- * particular randomness source.  They do this by keeping track of the
- * first and second order deltas of the event timings.
- *
- * Ensuring unpredictability at system startup
- * ============================================
- *
- * When any operating system starts up, it will go through a sequence
- * of actions that are fairly predictable by an adversary, especially
- * if the start-up does not involve interaction with a human operator.
- * This reduces the actual number of bits of unpredictability in the
- * entropy pool below the value in entropy_count.  In order to
- * counteract this effect, it helps to carry information in the
- * entropy pool across shut-downs and start-ups.  To do this, put the
- * following lines an appropriate script which is run during the boot
- * sequence:
- *
- *	echo "Initializing random number generator..."
- *	random_seed=/var/run/random-seed
- *	# Carry a random seed from start-up to start-up
- *	# Load and then save the whole entropy pool
- *	if [ -f $random_seed ]; then
- *		cat $random_seed >/dev/urandom
- *	else
- *		touch $random_seed
- *	fi
- *	chmod 600 $random_seed
- *	dd if=/dev/urandom of=$random_seed count=1 bs=512
- *
- * and the following lines in an appropriate script which is run as
- * the system is shutdown:
- *
- *	# Carry a random seed from shut-down to start-up
- *	# Save the whole entropy pool
- *	echo "Saving random seed..."
- *	random_seed=/var/run/random-seed
- *	touch $random_seed
- *	chmod 600 $random_seed
- *	dd if=/dev/urandom of=$random_seed count=1 bs=512
- *
- * For example, on most modern systems using the System V init
- * scripts, such code fragments would be found in
- * /etc/rc.d/init.d/random.  On older Linux systems, the correct script
- * location might be in /etc/rcb.d/rc.local or /etc/rc.d/rc.0.
- *
- * Effectively, these commands cause the contents of the entropy pool
- * to be saved at shut-down time and reloaded into the entropy pool at
- * start-up.  (The 'dd' in the addition to the bootup script is to
- * make sure that /etc/random-seed is different for every start-up,
- * even if the system crashes without executing rc.0.)  Even with
- * complete knowledge of the start-up activities, predicting the state
- * of the entropy pool requires knowledge of the previous history of
- * the system.
- *
- * Configuring the /dev/random driver under Linux
- * ==============================================
- *
- * The /dev/random driver under Linux uses minor numbers 8 and 9 of
- * the /dev/mem major number (#1).  So if your system does not have
- * /dev/random and /dev/urandom created already, they can be created
- * by using the commands:
- *
- * 	mknod /dev/random c 1 8
- * 	mknod /dev/urandom c 1 9
- *
- * Acknowledgements:
- * =================
- *
- * Ideas for constructing this random number generator were derived
- * from Pretty Good Privacy's random number generator, and from private
- * discussions with Phil Karn.  Colin Plumb provided a faster random
- * number generator, which speed up the mixing function of the entropy
- * pool, taken from PGPfone.  Dale Worley has also contributed many
- * useful ideas and suggestions to improve this driver.
- *
- * Any flaws in the design are solely my responsibility, and should
- * not be attributed to the Phil, Colin, or any of authors of PGP.
- *
- * Further background information on this topic may be obtained from
- * RFC 1750, "Randomness Recommendations for Security", by Donald
- * Eastlake, Steve Crocker, and Jeff Schiller.
+ *   - Initialization and readiness waiting.
+ *   - Fast key erasure RNG, the "crng".
+ *   - Entropy accumulation and extraction routines.
+ *   - Entropy collection routines.
+ *   - Userspace reader/writer interfaces.
+ *   - Sysctl interface.
+ *
+ * The high level overview is that there is one input pool, into which
+ * various pieces of data are hashed. Prior to initialization, some of that
+ * data is then "credited" as having a certain number of bits of entropy.
+ * When enough bits of entropy are available, the hash is finalized and
+ * handed as a key to a stream cipher that expands it indefinitely for
+ * various consumers. This key is periodically refreshed as the various
+ * entropy collectors, described below, add data to the input pool.
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
@@ -327,7 +43,6 @@
 #include <linux/spinlock.h>
 #include <linux/kthread.h>
 #include <linux/percpu.h>
-#include <linux/fips.h>
 #include <linux/ptrace.h>
 #include <linux/workqueue.h>
 #include <linux/irq.h>
@@ -335,1223 +50,1089 @@
 #include <linux/syscalls.h>
 #include <linux/completion.h>
 #include <linux/uuid.h>
+#include <linux/uaccess.h>
+#include <linux/siphash.h>
+#include <linux/uio.h>
 #include <crypto/chacha.h>
-#include <crypto/sha1.h>
-
+#include <crypto/blake2s.h>
 #include <asm/processor.h>
-#include <linux/uaccess.h>
 #include <asm/irq.h>
 #include <asm/irq_regs.h>
 #include <asm/io.h>
 
-#define CREATE_TRACE_POINTS
-#include <trace/events/random.h>
-
-/* #define ADD_INTERRUPT_BENCH */
-
-/*
- * Configuration information
- */
-#define INPUT_POOL_SHIFT	12
-#define INPUT_POOL_WORDS	(1 << (INPUT_POOL_SHIFT-5))
-#define OUTPUT_POOL_SHIFT	10
-#define OUTPUT_POOL_WORDS	(1 << (OUTPUT_POOL_SHIFT-5))
-#define EXTRACT_SIZE		10
-
-
-#define LONGS(x) (((x) + sizeof(unsigned long) - 1)/sizeof(unsigned long))
-
-/*
- * To allow fractional bits to be tracked, the entropy_count field is
- * denominated in units of 1/8th bits.
- *
- * 2*(ENTROPY_SHIFT + poolbitshift) must <= 31, or the multiply in
- * credit_entropy_bits() needs to be 64 bits wide.
- */
-#define ENTROPY_SHIFT 3
-#define ENTROPY_BITS(r) ((r)->entropy_count >> ENTROPY_SHIFT)
-
-/*
- * If the entropy count falls under this number of bits, then we
- * should wake up processes which are selecting or polling on write
- * access to /dev/random.
- */
-static int random_write_wakeup_bits = 28 * OUTPUT_POOL_WORDS;
-
-/*
- * Originally, we used a primitive polynomial of degree .poolwords
- * over GF(2).  The taps for various sizes are defined below.  They
- * were chosen to be evenly spaced except for the last tap, which is 1
- * to get the twisting happening as fast as possible.
- *
- * For the purposes of better mixing, we use the CRC-32 polynomial as
- * well to make a (modified) twisted Generalized Feedback Shift
- * Register.  (See M. Matsumoto & Y. Kurita, 1992.  Twisted GFSR
- * generators.  ACM Transactions on Modeling and Computer Simulation
- * 2(3):179-194.  Also see M. Matsumoto & Y. Kurita, 1994.  Twisted
- * GFSR generators II.  ACM Transactions on Modeling and Computer
- * Simulation 4:254-266)
- *
- * Thanks to Colin Plumb for suggesting this.
- *
- * The mixing operation is much less sensitive than the output hash,
- * where we use SHA-1.  All that we want of mixing operation is that
- * it be a good non-cryptographic hash; i.e. it not produce collisions
- * when fed "random" data of the sort we expect to see.  As long as
- * the pool state differs for different inputs, we have preserved the
- * input entropy and done a good job.  The fact that an intelligent
- * attacker can construct inputs that will produce controlled
- * alterations to the pool's state is not important because we don't
- * consider such inputs to contribute any randomness.  The only
- * property we need with respect to them is that the attacker can't
- * increase his/her knowledge of the pool's state.  Since all
- * additions are reversible (knowing the final state and the input,
- * you can reconstruct the initial state), if an attacker has any
- * uncertainty about the initial state, he/she can only shuffle that
- * uncertainty about, but never cause any collisions (which would
- * decrease the uncertainty).
- *
- * Our mixing functions were analyzed by Lacharme, Roeck, Strubel, and
- * Videau in their paper, "The Linux Pseudorandom Number Generator
- * Revisited" (see: http://eprint.iacr.org/2012/251.pdf).  In their
- * paper, they point out that we are not using a true Twisted GFSR,
- * since Matsumoto & Kurita used a trinomial feedback polynomial (that
- * is, with only three taps, instead of the six that we are using).
- * As a result, the resulting polynomial is neither primitive nor
- * irreducible, and hence does not have a maximal period over
- * GF(2**32).  They suggest a slight change to the generator
- * polynomial which improves the resulting TGFSR polynomial to be
- * irreducible, which we have made here.
- */
-static const struct poolinfo {
-	int poolbitshift, poolwords, poolbytes, poolfracbits;
-#define S(x) ilog2(x)+5, (x), (x)*4, (x) << (ENTROPY_SHIFT+5)
-	int tap1, tap2, tap3, tap4, tap5;
-} poolinfo_table[] = {
-	/* was: x^128 + x^103 + x^76 + x^51 +x^25 + x + 1 */
-	/* x^128 + x^104 + x^76 + x^51 +x^25 + x + 1 */
-	{ S(128),	104,	76,	51,	25,	1 },
-};
+/*********************************************************************
+ *
+ * Initialization and readiness waiting.
+ *
+ * Much of the RNG infrastructure is devoted to various dependencies
+ * being able to wait until the RNG has collected enough entropy and
+ * is ready for safe consumption.
+ *
+ *********************************************************************/
 
 /*
- * Static global variables
+ * crng_init is protected by base_crng->lock, and only increases
+ * its value (from empty->early->ready).
  */
-static DECLARE_WAIT_QUEUE_HEAD(random_write_wait);
+static enum {
+	CRNG_EMPTY = 0, /* Little to no entropy collected */
+	CRNG_EARLY = 1, /* At least POOL_EARLY_BITS collected */
+	CRNG_READY = 2  /* Fully initialized with POOL_READY_BITS collected */
+} crng_init __read_mostly = CRNG_EMPTY;
+#define crng_ready() (likely(crng_init >= CRNG_READY))
+/* Various types of waiters for crng_init->CRNG_READY transition. */
+static DECLARE_WAIT_QUEUE_HEAD(crng_init_wait);
 static struct fasync_struct *fasync;
+static DEFINE_SPINLOCK(random_ready_chain_lock);
+static RAW_NOTIFIER_HEAD(random_ready_chain);
 
-static DEFINE_SPINLOCK(random_ready_list_lock);
-static LIST_HEAD(random_ready_list);
-
-struct crng_state {
-	__u32		state[16];
-	unsigned long	init_time;
-	spinlock_t	lock;
-};
-
-static struct crng_state primary_crng = {
-	.lock = __SPIN_LOCK_UNLOCKED(primary_crng.lock),
-};
-
-/*
- * crng_init =  0 --> Uninitialized
- *		1 --> Initialized
- *		2 --> Initialized from input_pool
- *
- * crng_init is protected by primary_crng->lock, and only increases
- * its value (from 0->1->2).
- */
-static int crng_init = 0;
-#define crng_ready() (likely(crng_init > 1))
-static int crng_init_cnt = 0;
-static unsigned long crng_global_init_time = 0;
-#define CRNG_INIT_CNT_THRESH (2*CHACHA_KEY_SIZE)
-static void _extract_crng(struct crng_state *crng, __u8 out[CHACHA_BLOCK_SIZE]);
-static void _crng_backtrack_protect(struct crng_state *crng,
-				    __u8 tmp[CHACHA_BLOCK_SIZE], int used);
-static void process_random_ready_list(void);
-static void _get_random_bytes(void *buf, int nbytes);
-
-static struct ratelimit_state unseeded_warning =
-	RATELIMIT_STATE_INIT("warn_unseeded_randomness", HZ, 3);
+/* Control how we warn userspace. */
 static struct ratelimit_state urandom_warning =
-	RATELIMIT_STATE_INIT("warn_urandom_randomness", HZ, 3);
-
-static int ratelimit_disable __read_mostly;
-
+	RATELIMIT_STATE_INIT_FLAGS("urandom_warning", HZ, 3, RATELIMIT_MSG_ON_RELEASE);
+static int ratelimit_disable __read_mostly =
+	IS_ENABLED(CONFIG_WARN_ALL_UNSEEDED_RANDOM);
 module_param_named(ratelimit_disable, ratelimit_disable, int, 0644);
 MODULE_PARM_DESC(ratelimit_disable, "Disable random ratelimit suppression");
 
-/**********************************************************************
- *
- * OS independent entropy store.   Here are the functions which handle
- * storing entropy in an entropy pool.
+/*
+ * Returns whether or not the input pool has been seeded and thus guaranteed
+ * to supply cryptographically secure random numbers. This applies to: the
+ * /dev/urandom device, the get_random_bytes function, and the get_random_{u32,
+ * ,u64,int,long} family of functions.
  *
- **********************************************************************/
-
-struct entropy_store;
-struct entropy_store {
-	/* read-only data: */
-	const struct poolinfo *poolinfo;
-	__u32 *pool;
-	const char *name;
-
-	/* read-write data: */
-	spinlock_t lock;
-	unsigned short add_ptr;
-	unsigned short input_rotate;
-	int entropy_count;
-	unsigned int last_data_init:1;
-	__u8 last_data[EXTRACT_SIZE];
-};
-
-static ssize_t extract_entropy(struct entropy_store *r, void *buf,
-			       size_t nbytes, int min, int rsvd);
-static ssize_t _extract_entropy(struct entropy_store *r, void *buf,
-				size_t nbytes, int fips);
-
-static void crng_reseed(struct crng_state *crng, struct entropy_store *r);
-static __u32 input_pool_data[INPUT_POOL_WORDS] __latent_entropy;
-
-static struct entropy_store input_pool = {
-	.poolinfo = &poolinfo_table[0],
-	.name = "input",
-	.lock = __SPIN_LOCK_UNLOCKED(input_pool.lock),
-	.pool = input_pool_data
-};
+ * Returns: true if the input pool has been seeded.
+ *          false if the input pool has not been seeded.
+ */
+bool rng_is_initialized(void)
+{
+	return crng_ready();
+}
+EXPORT_SYMBOL(rng_is_initialized);
 
-static __u32 const twist_table[8] = {
-	0x00000000, 0x3b6e20c8, 0x76dc4190, 0x4db26158,
-	0xedb88320, 0xd6d6a3e8, 0x9b64c2b0, 0xa00ae278 };
+/* Used by wait_for_random_bytes(), and considered an entropy collector, below. */
+static void try_to_generate_entropy(void);
 
 /*
- * This function adds bytes into the entropy "pool".  It does not
- * update the entropy estimate.  The caller should call
- * credit_entropy_bits if this is appropriate.
+ * Wait for the input pool to be seeded and thus guaranteed to supply
+ * cryptographically secure random numbers. This applies to: the /dev/urandom
+ * device, the get_random_bytes function, and the get_random_{u32,u64,int,long}
+ * family of functions. Using any of these functions without first calling
+ * this function forfeits the guarantee of security.
  *
- * The pool is stirred with a primitive polynomial of the appropriate
- * degree, and then twisted.  We twist by three bits at a time because
- * it's cheap to do so and helps slightly in the expected case where
- * the entropy is concentrated in the low-order bits.
+ * Returns: 0 if the input pool has been seeded.
+ *          -ERESTARTSYS if the function was interrupted by a signal.
  */
-static void _mix_pool_bytes(struct entropy_store *r, const void *in,
-			    int nbytes)
+int wait_for_random_bytes(void)
 {
-	unsigned long i, tap1, tap2, tap3, tap4, tap5;
-	int input_rotate;
-	int wordmask = r->poolinfo->poolwords - 1;
-	const char *bytes = in;
-	__u32 w;
-
-	tap1 = r->poolinfo->tap1;
-	tap2 = r->poolinfo->tap2;
-	tap3 = r->poolinfo->tap3;
-	tap4 = r->poolinfo->tap4;
-	tap5 = r->poolinfo->tap5;
-
-	input_rotate = r->input_rotate;
-	i = r->add_ptr;
-
-	/* mix one byte at a time to simplify size handling and churn faster */
-	while (nbytes--) {
-		w = rol32(*bytes++, input_rotate);
-		i = (i - 1) & wordmask;
+	while (!crng_ready()) {
+		int ret;
 
-		/* XOR in the various taps */
-		w ^= r->pool[i];
-		w ^= r->pool[(i + tap1) & wordmask];
-		w ^= r->pool[(i + tap2) & wordmask];
-		w ^= r->pool[(i + tap3) & wordmask];
-		w ^= r->pool[(i + tap4) & wordmask];
-		w ^= r->pool[(i + tap5) & wordmask];
+		try_to_generate_entropy();
+		ret = wait_event_interruptible_timeout(crng_init_wait, crng_ready(), HZ);
+		if (ret)
+			return ret > 0 ? 0 : ret;
+	}
+	return 0;
+}
+EXPORT_SYMBOL(wait_for_random_bytes);
 
-		/* Mix the result back in with a twist */
-		r->pool[i] = (w >> 3) ^ twist_table[w & 7];
+/*
+ * Add a callback function that will be invoked when the input
+ * pool is initialised.
+ *
+ * returns: 0 if callback is successfully added
+ *	    -EALREADY if pool is already initialised (callback not called)
+ */
+int __cold register_random_ready_notifier(struct notifier_block *nb)
+{
+	unsigned long flags;
+	int ret = -EALREADY;
 
-		/*
-		 * Normally, we add 7 bits of rotation to the pool.
-		 * At the beginning of the pool, add an extra 7 bits
-		 * rotation, so that successive passes spread the
-		 * input bits across the pool evenly.
-		 */
-		input_rotate = (input_rotate + (i ? 7 : 14)) & 31;
-	}
+	if (crng_ready())
+		return ret;
 
-	r->input_rotate = input_rotate;
-	r->add_ptr = i;
+	spin_lock_irqsave(&random_ready_chain_lock, flags);
+	if (!crng_ready())
+		ret = raw_notifier_chain_register(&random_ready_chain, nb);
+	spin_unlock_irqrestore(&random_ready_chain_lock, flags);
+	return ret;
 }
 
-static void __mix_pool_bytes(struct entropy_store *r, const void *in,
-			     int nbytes)
+/*
+ * Delete a previously registered readiness callback function.
+ */
+int __cold unregister_random_ready_notifier(struct notifier_block *nb)
 {
-	trace_mix_pool_bytes_nolock(r->name, nbytes, _RET_IP_);
-	_mix_pool_bytes(r, in, nbytes);
+	unsigned long flags;
+	int ret;
+
+	spin_lock_irqsave(&random_ready_chain_lock, flags);
+	ret = raw_notifier_chain_unregister(&random_ready_chain, nb);
+	spin_unlock_irqrestore(&random_ready_chain_lock, flags);
+	return ret;
 }
 
-static void mix_pool_bytes(struct entropy_store *r, const void *in,
-			   int nbytes)
+static void __cold process_random_ready_list(void)
 {
 	unsigned long flags;
 
-	trace_mix_pool_bytes(r->name, nbytes, _RET_IP_);
-	spin_lock_irqsave(&r->lock, flags);
-	_mix_pool_bytes(r, in, nbytes);
-	spin_unlock_irqrestore(&r->lock, flags);
+	spin_lock_irqsave(&random_ready_chain_lock, flags);
+	raw_notifier_call_chain(&random_ready_chain, 0, NULL);
+	spin_unlock_irqrestore(&random_ready_chain_lock, flags);
 }
 
-struct fast_pool {
-	__u32		pool[4];
-	unsigned long	last;
-	unsigned short	reg_idx;
-	unsigned char	count;
-};
+#define warn_unseeded_randomness() \
+	if (IS_ENABLED(CONFIG_WARN_ALL_UNSEEDED_RANDOM) && !crng_ready()) \
+		printk_deferred(KERN_NOTICE "random: %s called from %pS with crng_init=%d\n", \
+				__func__, (void *)_RET_IP_, crng_init)
 
-/*
- * This is a fast mixing routine used by the interrupt randomness
- * collector.  It's hardcoded for an 128 bit pool and assumes that any
- * locks that might be needed are taken by the caller.
- */
-static void fast_mix(struct fast_pool *f)
-{
-	__u32 a = f->pool[0],	b = f->pool[1];
-	__u32 c = f->pool[2],	d = f->pool[3];
 
-	a += b;			c += d;
-	b = rol32(b, 6);	d = rol32(d, 27);
-	d ^= a;			b ^= c;
+/*********************************************************************
+ *
+ * Fast key erasure RNG, the "crng".
+ *
+ * These functions expand entropy from the entropy extractor into
+ * long streams for external consumption using the "fast key erasure"
+ * RNG described at <https://blog.cr.yp.to/20170723-random.html>.
+ *
+ * There are a few exported interfaces for use by other drivers:
+ *
+ *	void get_random_bytes(void *buf, size_t len)
+ *	u32 get_random_u32()
+ *	u64 get_random_u64()
+ *	unsigned int get_random_int()
+ *	unsigned long get_random_long()
+ *
+ * These interfaces will return the requested number of random bytes
+ * into the given buffer or as a return value. This is equivalent to
+ * a read from /dev/urandom. The u32, u64, int, and long family of
+ * functions may be higher performance for one-off random integers,
+ * because they do a bit of buffering and do not invoke reseeding
+ * until the buffer is emptied.
+ *
+ *********************************************************************/
 
-	a += b;			c += d;
-	b = rol32(b, 16);	d = rol32(d, 14);
-	d ^= a;			b ^= c;
+enum {
+	CRNG_RESEED_START_INTERVAL = HZ,
+	CRNG_RESEED_INTERVAL = 60 * HZ
+};
 
-	a += b;			c += d;
-	b = rol32(b, 6);	d = rol32(d, 27);
-	d ^= a;			b ^= c;
+static struct {
+	u8 key[CHACHA_KEY_SIZE] __aligned(__alignof__(long));
+	unsigned long birth;
+	unsigned long generation;
+	spinlock_t lock;
+} base_crng = {
+	.lock = __SPIN_LOCK_UNLOCKED(base_crng.lock)
+};
 
-	a += b;			c += d;
-	b = rol32(b, 16);	d = rol32(d, 14);
-	d ^= a;			b ^= c;
+struct crng {
+	u8 key[CHACHA_KEY_SIZE];
+	unsigned long generation;
+	local_lock_t lock;
+};
 
-	f->pool[0] = a;  f->pool[1] = b;
-	f->pool[2] = c;  f->pool[3] = d;
-	f->count++;
-}
+static DEFINE_PER_CPU(struct crng, crngs) = {
+	.generation = ULONG_MAX,
+	.lock = INIT_LOCAL_LOCK(crngs.lock),
+};
 
-static void process_random_ready_list(void)
+/* Used by crng_reseed() and crng_make_state() to extract a new seed from the input pool. */
+static void extract_entropy(void *buf, size_t len);
+
+/* This extracts a new crng key from the input pool. */
+static void crng_reseed(void)
 {
 	unsigned long flags;
-	struct random_ready_callback *rdy, *tmp;
+	unsigned long next_gen;
+	u8 key[CHACHA_KEY_SIZE];
 
-	spin_lock_irqsave(&random_ready_list_lock, flags);
-	list_for_each_entry_safe(rdy, tmp, &random_ready_list, list) {
-		struct module *owner = rdy->owner;
+	extract_entropy(key, sizeof(key));
 
-		list_del_init(&rdy->list);
-		rdy->func(rdy);
-		module_put(owner);
-	}
-	spin_unlock_irqrestore(&random_ready_list_lock, flags);
+	/*
+	 * We copy the new key into the base_crng, overwriting the old one,
+	 * and update the generation counter. We avoid hitting ULONG_MAX,
+	 * because the per-cpu crngs are initialized to ULONG_MAX, so this
+	 * forces new CPUs that come online to always initialize.
+	 */
+	spin_lock_irqsave(&base_crng.lock, flags);
+	memcpy(base_crng.key, key, sizeof(base_crng.key));
+	next_gen = base_crng.generation + 1;
+	if (next_gen == ULONG_MAX)
+		++next_gen;
+	WRITE_ONCE(base_crng.generation, next_gen);
+	WRITE_ONCE(base_crng.birth, jiffies);
+	if (!crng_ready())
+		crng_init = CRNG_READY;
+	spin_unlock_irqrestore(&base_crng.lock, flags);
+	memzero_explicit(key, sizeof(key));
 }
 
 /*
- * Credit (or debit) the entropy store with n bits of entropy.
- * Use credit_entropy_bits_safe() if the value comes from userspace
- * or otherwise should be checked for extreme values.
+ * This generates a ChaCha block using the provided key, and then
+ * immediately overwites that key with half the block. It returns
+ * the resultant ChaCha state to the user, along with the second
+ * half of the block containing 32 bytes of random data that may
+ * be used; random_data_len may not be greater than 32.
+ *
+ * The returned ChaCha state contains within it a copy of the old
+ * key value, at index 4, so the state should always be zeroed out
+ * immediately after using in order to maintain forward secrecy.
+ * If the state cannot be erased in a timely manner, then it is
+ * safer to set the random_data parameter to &chacha_state[4] so
+ * that this function overwrites it before returning.
  */
-static void credit_entropy_bits(struct entropy_store *r, int nbits)
+static void crng_fast_key_erasure(u8 key[CHACHA_KEY_SIZE],
+				  u32 chacha_state[CHACHA_STATE_WORDS],
+				  u8 *random_data, size_t random_data_len)
 {
-	int entropy_count, orig;
-	const int pool_size = r->poolinfo->poolfracbits;
-	int nfrac = nbits << ENTROPY_SHIFT;
+	u8 first_block[CHACHA_BLOCK_SIZE];
 
-	if (!nbits)
-		return;
+	BUG_ON(random_data_len > 32);
 
-retry:
-	entropy_count = orig = READ_ONCE(r->entropy_count);
-	if (nfrac < 0) {
-		/* Debit */
-		entropy_count += nfrac;
-	} else {
-		/*
-		 * Credit: we have to account for the possibility of
-		 * overwriting already present entropy.	 Even in the
-		 * ideal case of pure Shannon entropy, new contributions
-		 * approach the full value asymptotically:
-		 *
-		 * entropy <- entropy + (pool_size - entropy) *
-		 *	(1 - exp(-add_entropy/pool_size))
-		 *
-		 * For add_entropy <= pool_size/2 then
-		 * (1 - exp(-add_entropy/pool_size)) >=
-		 *    (add_entropy/pool_size)*0.7869...
-		 * so we can approximate the exponential with
-		 * 3/4*add_entropy/pool_size and still be on the
-		 * safe side by adding at most pool_size/2 at a time.
-		 *
-		 * The use of pool_size-2 in the while statement is to
-		 * prevent rounding artifacts from making the loop
-		 * arbitrarily long; this limits the loop to log2(pool_size)*2
-		 * turns no matter how large nbits is.
-		 */
-		int pnfrac = nfrac;
-		const int s = r->poolinfo->poolbitshift + ENTROPY_SHIFT + 2;
-		/* The +2 corresponds to the /4 in the denominator */
-
-		do {
-			unsigned int anfrac = min(pnfrac, pool_size/2);
-			unsigned int add =
-				((pool_size - entropy_count)*anfrac*3) >> s;
-
-			entropy_count += add;
-			pnfrac -= anfrac;
-		} while (unlikely(entropy_count < pool_size-2 && pnfrac));
-	}
-
-	if (WARN_ON(entropy_count < 0)) {
-		pr_warn("negative entropy/overflow: pool %s count %d\n",
-			r->name, entropy_count);
-		entropy_count = 0;
-	} else if (entropy_count > pool_size)
-		entropy_count = pool_size;
-	if (cmpxchg(&r->entropy_count, orig, entropy_count) != orig)
-		goto retry;
-
-	trace_credit_entropy_bits(r->name, nbits,
-				  entropy_count >> ENTROPY_SHIFT, _RET_IP_);
-
-	if (r == &input_pool) {
-		int entropy_bits = entropy_count >> ENTROPY_SHIFT;
-
-		if (crng_init < 2 && entropy_bits >= 128)
-			crng_reseed(&primary_crng, r);
-	}
+	chacha_init_consts(chacha_state);
+	memcpy(&chacha_state[4], key, CHACHA_KEY_SIZE);
+	memset(&chacha_state[12], 0, sizeof(u32) * 4);
+	chacha20_block(chacha_state, first_block);
+
+	memcpy(key, first_block, CHACHA_KEY_SIZE);
+	memcpy(random_data, first_block + CHACHA_KEY_SIZE, random_data_len);
+	memzero_explicit(first_block, sizeof(first_block));
 }
 
-static int credit_entropy_bits_safe(struct entropy_store *r, int nbits)
+/*
+ * Return whether the crng seed is considered to be sufficiently old
+ * that a reseeding is needed. This happens if the last reseeding
+ * was CRNG_RESEED_INTERVAL ago, or during early boot, at an interval
+ * proportional to the uptime.
+ */
+static bool crng_has_old_seed(void)
 {
-	const int nbits_max = r->poolinfo->poolwords * 32;
-
-	if (nbits < 0)
-		return -EINVAL;
-
-	/* Cap the value to avoid overflows */
-	nbits = min(nbits,  nbits_max);
+	static bool early_boot = true;
+	unsigned long interval = CRNG_RESEED_INTERVAL;
 
-	credit_entropy_bits(r, nbits);
-	return 0;
+	if (unlikely(READ_ONCE(early_boot))) {
+		time64_t uptime = ktime_get_seconds();
+		if (uptime >= CRNG_RESEED_INTERVAL / HZ * 2)
+			WRITE_ONCE(early_boot, false);
+		else
+			interval = max_t(unsigned int, CRNG_RESEED_START_INTERVAL,
+					 (unsigned int)uptime / 2 * HZ);
+	}
+	return time_is_before_jiffies(READ_ONCE(base_crng.birth) + interval);
 }
 
-/*********************************************************************
- *
- * CRNG using CHACHA20
- *
- *********************************************************************/
-
-#define CRNG_RESEED_INTERVAL (300*HZ)
-
-static DECLARE_WAIT_QUEUE_HEAD(crng_init_wait);
-
-#ifdef CONFIG_NUMA
 /*
- * Hack to deal with crazy userspace progams when they are all trying
- * to access /dev/urandom in parallel.  The programs are almost
- * certainly doing something terribly wrong, but we'll work around
- * their brain damage.
+ * This function returns a ChaCha state that you may use for generating
+ * random data. It also returns up to 32 bytes on its own of random data
+ * that may be used; random_data_len may not be greater than 32.
  */
-static struct crng_state **crng_node_pool __read_mostly;
-#endif
+static void crng_make_state(u32 chacha_state[CHACHA_STATE_WORDS],
+			    u8 *random_data, size_t random_data_len)
+{
+	unsigned long flags;
+	struct crng *crng;
 
-static void invalidate_batched_entropy(void);
-static void numa_crng_init(void);
+	BUG_ON(random_data_len > 32);
 
-static bool trust_cpu __ro_after_init = IS_ENABLED(CONFIG_RANDOM_TRUST_CPU);
-static int __init parse_trust_cpu(char *arg)
-{
-	return kstrtobool(arg, &trust_cpu);
-}
-early_param("random.trust_cpu", parse_trust_cpu);
+	/*
+	 * For the fast path, we check whether we're ready, unlocked first, and
+	 * then re-check once locked later. In the case where we're really not
+	 * ready, we do fast key erasure with the base_crng directly, extracting
+	 * when crng_init is CRNG_EMPTY.
+	 */
+	if (!crng_ready()) {
+		bool ready;
 
-static bool crng_init_try_arch(struct crng_state *crng)
-{
-	int		i;
-	bool		arch_init = true;
-	unsigned long	rv;
-
-	for (i = 4; i < 16; i++) {
-		if (!arch_get_random_seed_long(&rv) &&
-		    !arch_get_random_long(&rv)) {
-			rv = random_get_entropy();
-			arch_init = false;
+		spin_lock_irqsave(&base_crng.lock, flags);
+		ready = crng_ready();
+		if (!ready) {
+			if (crng_init == CRNG_EMPTY)
+				extract_entropy(base_crng.key, sizeof(base_crng.key));
+			crng_fast_key_erasure(base_crng.key, chacha_state,
+					      random_data, random_data_len);
 		}
-		crng->state[i] ^= rv;
+		spin_unlock_irqrestore(&base_crng.lock, flags);
+		if (!ready)
+			return;
 	}
 
-	return arch_init;
-}
+	/*
+	 * If the base_crng is old enough, we reseed, which in turn bumps the
+	 * generation counter that we check below.
+	 */
+	if (unlikely(crng_has_old_seed()))
+		crng_reseed();
 
-static bool __init crng_init_try_arch_early(struct crng_state *crng)
-{
-	int		i;
-	bool		arch_init = true;
-	unsigned long	rv;
+	local_lock_irqsave(&crngs.lock, flags);
+	crng = raw_cpu_ptr(&crngs);
 
-	for (i = 4; i < 16; i++) {
-		if (!arch_get_random_seed_long_early(&rv) &&
-		    !arch_get_random_long_early(&rv)) {
-			rv = random_get_entropy();
-			arch_init = false;
-		}
-		crng->state[i] ^= rv;
+	/*
+	 * If our per-cpu crng is older than the base_crng, then it means
+	 * somebody reseeded the base_crng. In that case, we do fast key
+	 * erasure on the base_crng, and use its output as the new key
+	 * for our per-cpu crng. This brings us up to date with base_crng.
+	 */
+	if (unlikely(crng->generation != READ_ONCE(base_crng.generation))) {
+		spin_lock(&base_crng.lock);
+		crng_fast_key_erasure(base_crng.key, chacha_state,
+				      crng->key, sizeof(crng->key));
+		crng->generation = base_crng.generation;
+		spin_unlock(&base_crng.lock);
 	}
 
-	return arch_init;
+	/*
+	 * Finally, when we've made it this far, our per-cpu crng has an up
+	 * to date key, and we can do fast key erasure with it to produce
+	 * some random data and a ChaCha state for the caller. All other
+	 * branches of this function are "unlikely", so most of the time we
+	 * should wind up here immediately.
+	 */
+	crng_fast_key_erasure(crng->key, chacha_state, random_data, random_data_len);
+	local_unlock_irqrestore(&crngs.lock, flags);
 }
 
-static void __maybe_unused crng_initialize_secondary(struct crng_state *crng)
+static void _get_random_bytes(void *buf, size_t len)
 {
-	chacha_init_consts(crng->state);
-	_get_random_bytes(&crng->state[4], sizeof(__u32) * 12);
-	crng_init_try_arch(crng);
-	crng->init_time = jiffies - CRNG_RESEED_INTERVAL - 1;
-}
+	u32 chacha_state[CHACHA_STATE_WORDS];
+	u8 tmp[CHACHA_BLOCK_SIZE];
+	size_t first_block_len;
 
-static void __init crng_initialize_primary(struct crng_state *crng)
-{
-	chacha_init_consts(crng->state);
-	_extract_entropy(&input_pool, &crng->state[4], sizeof(__u32) * 12, 0);
-	if (crng_init_try_arch_early(crng) && trust_cpu) {
-		invalidate_batched_entropy();
-		numa_crng_init();
-		crng_init = 2;
-		pr_notice("crng done (trusting CPU's manufacturer)\n");
-	}
-	crng->init_time = jiffies - CRNG_RESEED_INTERVAL - 1;
-}
+	if (!len)
+		return;
 
-#ifdef CONFIG_NUMA
-static void do_numa_crng_init(struct work_struct *work)
-{
-	int i;
-	struct crng_state *crng;
-	struct crng_state **pool;
+	first_block_len = min_t(size_t, 32, len);
+	crng_make_state(chacha_state, buf, first_block_len);
+	len -= first_block_len;
+	buf += first_block_len;
+
+	while (len) {
+		if (len < CHACHA_BLOCK_SIZE) {
+			chacha20_block(chacha_state, tmp);
+			memcpy(buf, tmp, len);
+			memzero_explicit(tmp, sizeof(tmp));
+			break;
+		}
 
-	pool = kcalloc(nr_node_ids, sizeof(*pool), GFP_KERNEL|__GFP_NOFAIL);
-	for_each_online_node(i) {
-		crng = kmalloc_node(sizeof(struct crng_state),
-				    GFP_KERNEL | __GFP_NOFAIL, i);
-		spin_lock_init(&crng->lock);
-		crng_initialize_secondary(crng);
-		pool[i] = crng;
-	}
-	mb();
-	if (cmpxchg(&crng_node_pool, NULL, pool)) {
-		for_each_node(i)
-			kfree(pool[i]);
-		kfree(pool);
+		chacha20_block(chacha_state, buf);
+		if (unlikely(chacha_state[12] == 0))
+			++chacha_state[13];
+		len -= CHACHA_BLOCK_SIZE;
+		buf += CHACHA_BLOCK_SIZE;
 	}
-}
-
-static DECLARE_WORK(numa_crng_init_work, do_numa_crng_init);
 
-static void numa_crng_init(void)
-{
-	schedule_work(&numa_crng_init_work);
+	memzero_explicit(chacha_state, sizeof(chacha_state));
 }
-#else
-static void numa_crng_init(void) {}
-#endif
 
 /*
- * crng_fast_load() can be called by code in the interrupt service
- * path.  So we can't afford to dilly-dally.
+ * This function is the exported kernel interface.  It returns some
+ * number of good random numbers, suitable for key generation, seeding
+ * TCP sequence numbers, etc.  It does not rely on the hardware random
+ * number generator.  For random bytes direct from the hardware RNG
+ * (when available), use get_random_bytes_arch(). In order to ensure
+ * that the randomness provided by this function is okay, the function
+ * wait_for_random_bytes() should be called and return 0 at least once
+ * at any point prior.
  */
-static int crng_fast_load(const char *cp, size_t len)
+void get_random_bytes(void *buf, size_t len)
 {
-	unsigned long flags;
-	char *p;
-
-	if (!spin_trylock_irqsave(&primary_crng.lock, flags))
-		return 0;
-	if (crng_init != 0) {
-		spin_unlock_irqrestore(&primary_crng.lock, flags);
-		return 0;
-	}
-	p = (unsigned char *) &primary_crng.state[4];
-	while (len > 0 && crng_init_cnt < CRNG_INIT_CNT_THRESH) {
-		p[crng_init_cnt % CHACHA_KEY_SIZE] ^= *cp;
-		cp++; crng_init_cnt++; len--;
-	}
-	spin_unlock_irqrestore(&primary_crng.lock, flags);
-	if (crng_init_cnt >= CRNG_INIT_CNT_THRESH) {
-		invalidate_batched_entropy();
-		crng_init = 1;
-		pr_notice("fast init done\n");
-	}
-	return 1;
+	warn_unseeded_randomness();
+	_get_random_bytes(buf, len);
 }
+EXPORT_SYMBOL(get_random_bytes);
 
-/*
- * crng_slow_load() is called by add_device_randomness, which has two
- * attributes.  (1) We can't trust the buffer passed to it is
- * guaranteed to be unpredictable (so it might not have any entropy at
- * all), and (2) it doesn't have the performance constraints of
- * crng_fast_load().
- *
- * So we do something more comprehensive which is guaranteed to touch
- * all of the primary_crng's state, and which uses a LFSR with a
- * period of 255 as part of the mixing algorithm.  Finally, we do
- * *not* advance crng_init_cnt since buffer we may get may be something
- * like a fixed DMI table (for example), which might very well be
- * unique to the machine, but is otherwise unvarying.
- */
-static int crng_slow_load(const char *cp, size_t len)
-{
-	unsigned long		flags;
-	static unsigned char	lfsr = 1;
-	unsigned char		tmp;
-	unsigned		i, max = CHACHA_KEY_SIZE;
-	const char *		src_buf = cp;
-	char *			dest_buf = (char *) &primary_crng.state[4];
+static ssize_t get_random_bytes_user(struct iov_iter *iter)
+{
+	u32 chacha_state[CHACHA_STATE_WORDS];
+	u8 block[CHACHA_BLOCK_SIZE];
+	size_t ret = 0, copied;
 
-	if (!spin_trylock_irqsave(&primary_crng.lock, flags))
-		return 0;
-	if (crng_init != 0) {
-		spin_unlock_irqrestore(&primary_crng.lock, flags);
+	if (unlikely(!iov_iter_count(iter)))
 		return 0;
+
+	/*
+	 * Immediately overwrite the ChaCha key at index 4 with random
+	 * bytes, in case userspace causes copy_to_iter() below to sleep
+	 * forever, so that we still retain forward secrecy in that case.
+	 */
+	crng_make_state(chacha_state, (u8 *)&chacha_state[4], CHACHA_KEY_SIZE);
+	/*
+	 * However, if we're doing a read of len <= 32, we don't need to
+	 * use chacha_state after, so we can simply return those bytes to
+	 * the user directly.
+	 */
+	if (iov_iter_count(iter) <= CHACHA_KEY_SIZE) {
+		ret = copy_to_iter(&chacha_state[4], CHACHA_KEY_SIZE, iter);
+		goto out_zero_chacha;
 	}
-	if (len > max)
-		max = len;
 
-	for (i = 0; i < max ; i++) {
-		tmp = lfsr;
-		lfsr >>= 1;
-		if (tmp & 1)
-			lfsr ^= 0xE1;
-		tmp = dest_buf[i % CHACHA_KEY_SIZE];
-		dest_buf[i % CHACHA_KEY_SIZE] ^= src_buf[i % len] ^ lfsr;
-		lfsr += (tmp << 3) | (tmp >> 5);
-	}
-	spin_unlock_irqrestore(&primary_crng.lock, flags);
-	return 1;
-}
-
-static void crng_reseed(struct crng_state *crng, struct entropy_store *r)
-{
-	unsigned long	flags;
-	int		i, num;
-	union {
-		__u8	block[CHACHA_BLOCK_SIZE];
-		__u32	key[8];
-	} buf;
-
-	if (r) {
-		num = extract_entropy(r, &buf, 32, 16, 0);
-		if (num == 0)
-			return;
-	} else {
-		_extract_crng(&primary_crng, buf.block);
-		_crng_backtrack_protect(&primary_crng, buf.block,
-					CHACHA_KEY_SIZE);
-	}
-	spin_lock_irqsave(&crng->lock, flags);
-	for (i = 0; i < 8; i++) {
-		unsigned long	rv;
-		if (!arch_get_random_seed_long(&rv) &&
-		    !arch_get_random_long(&rv))
-			rv = random_get_entropy();
-		crng->state[i+4] ^= buf.key[i] ^ rv;
-	}
-	memzero_explicit(&buf, sizeof(buf));
-	crng->init_time = jiffies;
-	spin_unlock_irqrestore(&crng->lock, flags);
-	if (crng == &primary_crng && crng_init < 2) {
-		invalidate_batched_entropy();
-		numa_crng_init();
-		crng_init = 2;
-		process_random_ready_list();
-		wake_up_interruptible(&crng_init_wait);
-		kill_fasync(&fasync, SIGIO, POLL_IN);
-		pr_notice("crng init done\n");
-		if (unseeded_warning.missed) {
-			pr_notice("%d get_random_xx warning(s) missed due to ratelimiting\n",
-				  unseeded_warning.missed);
-			unseeded_warning.missed = 0;
-		}
-		if (urandom_warning.missed) {
-			pr_notice("%d urandom warning(s) missed due to ratelimiting\n",
-				  urandom_warning.missed);
-			urandom_warning.missed = 0;
+	for (;;) {
+		chacha20_block(chacha_state, block);
+		if (unlikely(chacha_state[12] == 0))
+			++chacha_state[13];
+
+		copied = copy_to_iter(block, sizeof(block), iter);
+		ret += copied;
+		if (!iov_iter_count(iter) || copied != sizeof(block))
+			break;
+
+		BUILD_BUG_ON(PAGE_SIZE % sizeof(block) != 0);
+		if (ret % PAGE_SIZE == 0) {
+			if (signal_pending(current))
+				break;
+			cond_resched();
 		}
 	}
-}
 
-static void _extract_crng(struct crng_state *crng,
-			  __u8 out[CHACHA_BLOCK_SIZE])
-{
-	unsigned long v, flags;
-
-	if (crng_ready() &&
-	    (time_after(crng_global_init_time, crng->init_time) ||
-	     time_after(jiffies, crng->init_time + CRNG_RESEED_INTERVAL)))
-		crng_reseed(crng, crng == &primary_crng ? &input_pool : NULL);
-	spin_lock_irqsave(&crng->lock, flags);
-	if (arch_get_random_long(&v))
-		crng->state[14] ^= v;
-	chacha20_block(&crng->state[0], out);
-	if (crng->state[12] == 0)
-		crng->state[13]++;
-	spin_unlock_irqrestore(&crng->lock, flags);
-}
-
-static void extract_crng(__u8 out[CHACHA_BLOCK_SIZE])
-{
-	struct crng_state *crng = NULL;
-
-#ifdef CONFIG_NUMA
-	if (crng_node_pool)
-		crng = crng_node_pool[numa_node_id()];
-	if (crng == NULL)
-#endif
-		crng = &primary_crng;
-	_extract_crng(crng, out);
-}
+	memzero_explicit(block, sizeof(block));
+out_zero_chacha:
+	memzero_explicit(chacha_state, sizeof(chacha_state));
+	return ret ? ret : -EFAULT;
+}
+
+/*
+ * Batched entropy returns random integers. The quality of the random
+ * number is good as /dev/urandom. In order to ensure that the randomness
+ * provided by this function is okay, the function wait_for_random_bytes()
+ * should be called and return 0 at least once at any point prior.
+ */
+
+#define DEFINE_BATCHED_ENTROPY(type)						\
+struct batch_ ##type {								\
+	/*									\
+	 * We make this 1.5x a ChaCha block, so that we get the			\
+	 * remaining 32 bytes from fast key erasure, plus one full		\
+	 * block from the detached ChaCha state. We can increase		\
+	 * the size of this later if needed so long as we keep the		\
+	 * formula of (integer_blocks + 0.5) * CHACHA_BLOCK_SIZE.		\
+	 */									\
+	type entropy[CHACHA_BLOCK_SIZE * 3 / (2 * sizeof(type))];		\
+	local_lock_t lock;							\
+	unsigned long generation;						\
+	unsigned int position;							\
+};										\
+										\
+static DEFINE_PER_CPU(struct batch_ ##type, batched_entropy_ ##type) = {	\
+	.lock = INIT_LOCAL_LOCK(batched_entropy_ ##type.lock),			\
+	.position = UINT_MAX							\
+};										\
+										\
+type get_random_ ##type(void)							\
+{										\
+	type ret;								\
+	unsigned long flags;							\
+	struct batch_ ##type *batch;						\
+	unsigned long next_gen;							\
+										\
+	warn_unseeded_randomness();						\
+										\
+	if  (!crng_ready()) {							\
+		_get_random_bytes(&ret, sizeof(ret));				\
+		return ret;							\
+	}									\
+										\
+	local_lock_irqsave(&batched_entropy_ ##type.lock, flags);		\
+	batch = raw_cpu_ptr(&batched_entropy_##type);				\
+										\
+	next_gen = READ_ONCE(base_crng.generation);				\
+	if (batch->position >= ARRAY_SIZE(batch->entropy) ||			\
+	    next_gen != batch->generation) {					\
+		_get_random_bytes(batch->entropy, sizeof(batch->entropy));	\
+		batch->position = 0;						\
+		batch->generation = next_gen;					\
+	}									\
+										\
+	ret = batch->entropy[batch->position];					\
+	batch->entropy[batch->position] = 0;					\
+	++batch->position;							\
+	local_unlock_irqrestore(&batched_entropy_ ##type.lock, flags);		\
+	return ret;								\
+}										\
+EXPORT_SYMBOL(get_random_ ##type);
+
+DEFINE_BATCHED_ENTROPY(u64)
+DEFINE_BATCHED_ENTROPY(u32)
 
+#ifdef CONFIG_SMP
 /*
- * Use the leftover bytes from the CRNG block output (if there is
- * enough) to mutate the CRNG key to provide backtracking protection.
+ * This function is called when the CPU is coming up, with entry
+ * CPUHP_RANDOM_PREPARE, which comes before CPUHP_WORKQUEUE_PREP.
  */
-static void _crng_backtrack_protect(struct crng_state *crng,
-				    __u8 tmp[CHACHA_BLOCK_SIZE], int used)
+int __cold random_prepare_cpu(unsigned int cpu)
 {
-	unsigned long	flags;
-	__u32		*s, *d;
-	int		i;
-
-	used = round_up(used, sizeof(__u32));
-	if (used + CHACHA_KEY_SIZE > CHACHA_BLOCK_SIZE) {
-		extract_crng(tmp);
-		used = 0;
-	}
-	spin_lock_irqsave(&crng->lock, flags);
-	s = (__u32 *) &tmp[used];
-	d = &crng->state[4];
-	for (i=0; i < 8; i++)
-		*d++ ^= *s++;
-	spin_unlock_irqrestore(&crng->lock, flags);
+	/*
+	 * When the cpu comes back online, immediately invalidate both
+	 * the per-cpu crng and all batches, so that we serve fresh
+	 * randomness.
+	 */
+	per_cpu_ptr(&crngs, cpu)->generation = ULONG_MAX;
+	per_cpu_ptr(&batched_entropy_u32, cpu)->position = UINT_MAX;
+	per_cpu_ptr(&batched_entropy_u64, cpu)->position = UINT_MAX;
+	return 0;
 }
-
-static void crng_backtrack_protect(__u8 tmp[CHACHA_BLOCK_SIZE], int used)
-{
-	struct crng_state *crng = NULL;
-
-#ifdef CONFIG_NUMA
-	if (crng_node_pool)
-		crng = crng_node_pool[numa_node_id()];
-	if (crng == NULL)
 #endif
-		crng = &primary_crng;
-	_crng_backtrack_protect(crng, tmp, used);
-}
 
-static ssize_t extract_crng_user(void __user *buf, size_t nbytes)
+/*
+ * This function will use the architecture-specific hardware random
+ * number generator if it is available. It is not recommended for
+ * use. Use get_random_bytes() instead. It returns the number of
+ * bytes filled in.
+ */
+size_t __must_check get_random_bytes_arch(void *buf, size_t len)
 {
-	ssize_t ret = 0, i = CHACHA_BLOCK_SIZE;
-	__u8 tmp[CHACHA_BLOCK_SIZE] __aligned(4);
-	int large_request = (nbytes > 256);
+	size_t left = len;
+	u8 *p = buf;
 
-	while (nbytes) {
-		if (large_request && need_resched()) {
-			if (signal_pending(current)) {
-				if (ret == 0)
-					ret = -ERESTARTSYS;
-				break;
-			}
-			schedule();
-		}
+	while (left) {
+		unsigned long v;
+		size_t block_len = min_t(size_t, left, sizeof(unsigned long));
 
-		extract_crng(tmp);
-		i = min_t(int, nbytes, CHACHA_BLOCK_SIZE);
-		if (copy_to_user(buf, tmp, i)) {
-			ret = -EFAULT;
+		if (!arch_get_random_long(&v))
 			break;
-		}
 
-		nbytes -= i;
-		buf += i;
-		ret += i;
+		memcpy(p, &v, block_len);
+		p += block_len;
+		left -= block_len;
 	}
-	crng_backtrack_protect(tmp, i);
-
-	/* Wipe data just written to memory */
-	memzero_explicit(tmp, sizeof(tmp));
 
-	return ret;
+	return len - left;
 }
+EXPORT_SYMBOL(get_random_bytes_arch);
 
 
-/*********************************************************************
+/**********************************************************************
  *
- * Entropy input management
+ * Entropy accumulation and extraction routines.
  *
- *********************************************************************/
+ * Callers may add entropy via:
+ *
+ *     static void mix_pool_bytes(const void *buf, size_t len)
+ *
+ * After which, if added entropy should be credited:
+ *
+ *     static void credit_init_bits(size_t bits)
+ *
+ * Finally, extract entropy via:
+ *
+ *     static void extract_entropy(void *buf, size_t len)
+ *
+ **********************************************************************/
 
-/* There is one of these per entropy source */
-struct timer_rand_state {
-	cycles_t last_time;
-	long last_delta, last_delta2;
+enum {
+	POOL_BITS = BLAKE2S_HASH_SIZE * 8,
+	POOL_READY_BITS = POOL_BITS, /* When crng_init->CRNG_READY */
+	POOL_EARLY_BITS = POOL_READY_BITS / 2 /* When crng_init->CRNG_EARLY */
 };
 
-#define INIT_TIMER_RAND_STATE { INITIAL_JIFFIES, };
+static struct {
+	struct blake2s_state hash;
+	spinlock_t lock;
+	unsigned int init_bits;
+} input_pool = {
+	.hash.h = { BLAKE2S_IV0 ^ (0x01010000 | BLAKE2S_HASH_SIZE),
+		    BLAKE2S_IV1, BLAKE2S_IV2, BLAKE2S_IV3, BLAKE2S_IV4,
+		    BLAKE2S_IV5, BLAKE2S_IV6, BLAKE2S_IV7 },
+	.hash.outlen = BLAKE2S_HASH_SIZE,
+	.lock = __SPIN_LOCK_UNLOCKED(input_pool.lock),
+};
+
+static void _mix_pool_bytes(const void *buf, size_t len)
+{
+	blake2s_update(&input_pool.hash, buf, len);
+}
 
 /*
- * Add device- or boot-specific data to the input pool to help
- * initialize it.
- *
- * None of this adds any entropy; it is meant to avoid the problem of
- * the entropy pool having similar initial state across largely
- * identical devices.
+ * This function adds bytes into the input pool. It does not
+ * update the initialization bit counter; the caller should call
+ * credit_init_bits if this is appropriate.
  */
-void add_device_randomness(const void *buf, unsigned int size)
+static void mix_pool_bytes(const void *buf, size_t len)
 {
-	unsigned long time = random_get_entropy() ^ jiffies;
 	unsigned long flags;
 
-	if (!crng_ready() && size)
-		crng_slow_load(buf, size);
-
-	trace_add_device_randomness(size, _RET_IP_);
 	spin_lock_irqsave(&input_pool.lock, flags);
-	_mix_pool_bytes(&input_pool, buf, size);
-	_mix_pool_bytes(&input_pool, &time, sizeof(time));
+	_mix_pool_bytes(buf, len);
 	spin_unlock_irqrestore(&input_pool.lock, flags);
 }
-EXPORT_SYMBOL(add_device_randomness);
-
-static struct timer_rand_state input_timer_state = INIT_TIMER_RAND_STATE;
 
 /*
- * This function adds entropy to the entropy "pool" by using timing
- * delays.  It uses the timer_rand_state structure to make an estimate
- * of how many bits of entropy this call has added to the pool.
- *
- * The number "num" is also added to the pool - it should somehow describe
- * the type of event which just happened.  This is currently 0-255 for
- * keyboard scan codes, and 256 upwards for interrupts.
- *
+ * This is an HKDF-like construction for using the hashed collected entropy
+ * as a PRF key, that's then expanded block-by-block.
  */
-static void add_timer_randomness(struct timer_rand_state *state, unsigned num)
+static void extract_entropy(void *buf, size_t len)
 {
-	struct entropy_store	*r;
+	unsigned long flags;
+	u8 seed[BLAKE2S_HASH_SIZE], next_key[BLAKE2S_HASH_SIZE];
 	struct {
-		long jiffies;
-		unsigned cycles;
-		unsigned num;
-	} sample;
-	long delta, delta2, delta3;
+		unsigned long rdseed[32 / sizeof(long)];
+		size_t counter;
+	} block;
+	size_t i;
+
+	for (i = 0; i < ARRAY_SIZE(block.rdseed); ++i) {
+		if (!arch_get_random_seed_long(&block.rdseed[i]) &&
+		    !arch_get_random_long(&block.rdseed[i]))
+			block.rdseed[i] = random_get_entropy();
+	}
 
-	sample.jiffies = jiffies;
-	sample.cycles = random_get_entropy();
-	sample.num = num;
-	r = &input_pool;
-	mix_pool_bytes(r, &sample, sizeof(sample));
+	spin_lock_irqsave(&input_pool.lock, flags);
 
-	/*
-	 * Calculate number of bits of randomness we probably added.
-	 * We take into account the first, second and third-order deltas
-	 * in order to make our estimate.
-	 */
-	delta = sample.jiffies - READ_ONCE(state->last_time);
-	WRITE_ONCE(state->last_time, sample.jiffies);
+	/* seed = HASHPRF(last_key, entropy_input) */
+	blake2s_final(&input_pool.hash, seed);
 
-	delta2 = delta - READ_ONCE(state->last_delta);
-	WRITE_ONCE(state->last_delta, delta);
+	/* next_key = HASHPRF(seed, RDSEED || 0) */
+	block.counter = 0;
+	blake2s(next_key, (u8 *)&block, seed, sizeof(next_key), sizeof(block), sizeof(seed));
+	blake2s_init_key(&input_pool.hash, BLAKE2S_HASH_SIZE, next_key, sizeof(next_key));
 
-	delta3 = delta2 - READ_ONCE(state->last_delta2);
-	WRITE_ONCE(state->last_delta2, delta2);
+	spin_unlock_irqrestore(&input_pool.lock, flags);
+	memzero_explicit(next_key, sizeof(next_key));
 
-	if (delta < 0)
-		delta = -delta;
-	if (delta2 < 0)
-		delta2 = -delta2;
-	if (delta3 < 0)
-		delta3 = -delta3;
-	if (delta > delta2)
-		delta = delta2;
-	if (delta > delta3)
-		delta = delta3;
+	while (len) {
+		i = min_t(size_t, len, BLAKE2S_HASH_SIZE);
+		/* output = HASHPRF(seed, RDSEED || ++counter) */
+		++block.counter;
+		blake2s(buf, (u8 *)&block, seed, i, sizeof(block), sizeof(seed));
+		len -= i;
+		buf += i;
+	}
 
-	/*
-	 * delta is now minimum absolute delta.
-	 * Round down by 1 bit on general principles,
-	 * and limit entropy estimate to 12 bits.
-	 */
-	credit_entropy_bits(r, min_t(int, fls(delta>>1), 11));
+	memzero_explicit(seed, sizeof(seed));
+	memzero_explicit(&block, sizeof(block));
 }
 
-void add_input_randomness(unsigned int type, unsigned int code,
-				 unsigned int value)
+#define credit_init_bits(bits) if (!crng_ready()) _credit_init_bits(bits)
+
+static void __cold _credit_init_bits(size_t bits)
 {
-	static unsigned char last_value;
+	unsigned int new, orig, add;
+	unsigned long flags;
 
-	/* ignore autorepeat and the like */
-	if (value == last_value)
+	if (!bits)
 		return;
 
-	last_value = value;
-	add_timer_randomness(&input_timer_state,
-			     (type << 4) ^ code ^ (code >> 4) ^ value);
-	trace_add_input_randomness(ENTROPY_BITS(&input_pool));
-}
-EXPORT_SYMBOL_GPL(add_input_randomness);
+	add = min_t(size_t, bits, POOL_BITS);
 
-static DEFINE_PER_CPU(struct fast_pool, irq_randomness);
+	do {
+		orig = READ_ONCE(input_pool.init_bits);
+		new = min_t(unsigned int, POOL_BITS, orig + add);
+	} while (cmpxchg(&input_pool.init_bits, orig, new) != orig);
 
-#ifdef ADD_INTERRUPT_BENCH
-static unsigned long avg_cycles, avg_deviation;
+	if (orig < POOL_READY_BITS && new >= POOL_READY_BITS) {
+		crng_reseed(); /* Sets crng_init to CRNG_READY under base_crng.lock. */
+		process_random_ready_list();
+		wake_up_interruptible(&crng_init_wait);
+		kill_fasync(&fasync, SIGIO, POLL_IN);
+		pr_notice("crng init done\n");
+		if (urandom_warning.missed)
+			pr_notice("%d urandom warning(s) missed due to ratelimiting\n",
+				  urandom_warning.missed);
+	} else if (orig < POOL_EARLY_BITS && new >= POOL_EARLY_BITS) {
+		spin_lock_irqsave(&base_crng.lock, flags);
+		/* Check if crng_init is CRNG_EMPTY, to avoid race with crng_reseed(). */
+		if (crng_init == CRNG_EMPTY) {
+			extract_entropy(base_crng.key, sizeof(base_crng.key));
+			crng_init = CRNG_EARLY;
+		}
+		spin_unlock_irqrestore(&base_crng.lock, flags);
+	}
+}
 
-#define AVG_SHIFT 8     /* Exponential average factor k=1/256 */
-#define FIXED_1_2 (1 << (AVG_SHIFT-1))
 
-static void add_interrupt_bench(cycles_t start)
-{
-        long delta = random_get_entropy() - start;
+/**********************************************************************
+ *
+ * Entropy collection routines.
+ *
+ * The following exported functions are used for pushing entropy into
+ * the above entropy accumulation routines:
+ *
+ *	void add_device_randomness(const void *buf, size_t len);
+ *	void add_hwgenerator_randomness(const void *buf, size_t len, size_t entropy);
+ *	void add_bootloader_randomness(const void *buf, size_t len);
+ *	void add_interrupt_randomness(int irq);
+ *	void add_input_randomness(unsigned int type, unsigned int code, unsigned int value);
+ *	void add_disk_randomness(struct gendisk *disk);
+ *
+ * add_device_randomness() adds data to the input pool that
+ * is likely to differ between two devices (or possibly even per boot).
+ * This would be things like MAC addresses or serial numbers, or the
+ * read-out of the RTC. This does *not* credit any actual entropy to
+ * the pool, but it initializes the pool to different values for devices
+ * that might otherwise be identical and have very little entropy
+ * available to them (particularly common in the embedded world).
+ *
+ * add_hwgenerator_randomness() is for true hardware RNGs, and will credit
+ * entropy as specified by the caller. If the entropy pool is full it will
+ * block until more entropy is needed.
+ *
+ * add_bootloader_randomness() is called by bootloader drivers, such as EFI
+ * and device tree, and credits its input depending on whether or not the
+ * configuration option CONFIG_RANDOM_TRUST_BOOTLOADER is set.
+ *
+ * add_interrupt_randomness() uses the interrupt timing as random
+ * inputs to the entropy pool. Using the cycle counters and the irq source
+ * as inputs, it feeds the input pool roughly once a second or after 64
+ * interrupts, crediting 1 bit of entropy for whichever comes first.
+ *
+ * add_input_randomness() uses the input layer interrupt timing, as well
+ * as the event type information from the hardware.
+ *
+ * add_disk_randomness() uses what amounts to the seek time of block
+ * layer request events, on a per-disk_devt basis, as input to the
+ * entropy pool. Note that high-speed solid state drives with very low
+ * seek times do not make for good sources of entropy, as their seek
+ * times are usually fairly consistent.
+ *
+ * The last two routines try to estimate how many bits of entropy
+ * to credit. They do this by keeping track of the first and second
+ * order deltas of the event timings.
+ *
+ **********************************************************************/
 
-        /* Use a weighted moving average */
-        delta = delta - ((avg_cycles + FIXED_1_2) >> AVG_SHIFT);
-        avg_cycles += delta;
-        /* And average deviation */
-        delta = abs(delta) - ((avg_deviation + FIXED_1_2) >> AVG_SHIFT);
-        avg_deviation += delta;
+static bool trust_cpu __initdata = IS_ENABLED(CONFIG_RANDOM_TRUST_CPU);
+static bool trust_bootloader __initdata = IS_ENABLED(CONFIG_RANDOM_TRUST_BOOTLOADER);
+static int __init parse_trust_cpu(char *arg)
+{
+	return kstrtobool(arg, &trust_cpu);
 }
-#else
-#define add_interrupt_bench(x)
-#endif
+static int __init parse_trust_bootloader(char *arg)
+{
+	return kstrtobool(arg, &trust_bootloader);
+}
+early_param("random.trust_cpu", parse_trust_cpu);
+early_param("random.trust_bootloader", parse_trust_bootloader);
 
-static __u32 get_reg(struct fast_pool *f, struct pt_regs *regs)
+/*
+ * The first collection of entropy occurs at system boot while interrupts
+ * are still turned off. Here we push in latent entropy, RDSEED, a timestamp,
+ * utsname(), and the command line. Depending on the above configuration knob,
+ * RDSEED may be considered sufficient for initialization. Note that much
+ * earlier setup may already have pushed entropy into the input pool by the
+ * time we get here.
+ */
+int __init random_init(const char *command_line)
 {
-	__u32 *ptr = (__u32 *) regs;
-	unsigned int idx;
+	ktime_t now = ktime_get_real();
+	unsigned int i, arch_bits;
+	unsigned long entropy;
 
-	if (regs == NULL)
-		return 0;
-	idx = READ_ONCE(f->reg_idx);
-	if (idx >= sizeof(struct pt_regs) / sizeof(__u32))
-		idx = 0;
-	ptr += idx++;
-	WRITE_ONCE(f->reg_idx, idx);
-	return *ptr;
-}
-
-void add_interrupt_randomness(int irq, int irq_flags)
-{
-	struct entropy_store	*r;
-	struct fast_pool	*fast_pool = this_cpu_ptr(&irq_randomness);
-	struct pt_regs		*regs = get_irq_regs();
-	unsigned long		now = jiffies;
-	cycles_t		cycles = random_get_entropy();
-	__u32			c_high, j_high;
-	__u64			ip;
-
-	if (cycles == 0)
-		cycles = get_reg(fast_pool, regs);
-	c_high = (sizeof(cycles) > 4) ? cycles >> 32 : 0;
-	j_high = (sizeof(now) > 4) ? now >> 32 : 0;
-	fast_pool->pool[0] ^= cycles ^ j_high ^ irq;
-	fast_pool->pool[1] ^= now ^ c_high;
-	ip = regs ? instruction_pointer(regs) : _RET_IP_;
-	fast_pool->pool[2] ^= ip;
-	fast_pool->pool[3] ^= (sizeof(ip) > 4) ? ip >> 32 :
-		get_reg(fast_pool, regs);
-
-	fast_mix(fast_pool);
-	add_interrupt_bench(cycles);
-
-	if (unlikely(crng_init == 0)) {
-		if ((fast_pool->count >= 64) &&
-		    crng_fast_load((char *) fast_pool->pool,
-				   sizeof(fast_pool->pool))) {
-			fast_pool->count = 0;
-			fast_pool->last = now;
+#if defined(LATENT_ENTROPY_PLUGIN)
+	static const u8 compiletime_seed[BLAKE2S_BLOCK_SIZE] __initconst __latent_entropy;
+	_mix_pool_bytes(compiletime_seed, sizeof(compiletime_seed));
+#endif
+
+	for (i = 0, arch_bits = BLAKE2S_BLOCK_SIZE * 8;
+	     i < BLAKE2S_BLOCK_SIZE; i += sizeof(entropy)) {
+		if (!arch_get_random_seed_long_early(&entropy) &&
+		    !arch_get_random_long_early(&entropy)) {
+			entropy = random_get_entropy();
+			arch_bits -= sizeof(entropy) * 8;
 		}
-		return;
+		_mix_pool_bytes(&entropy, sizeof(entropy));
 	}
+	_mix_pool_bytes(&now, sizeof(now));
+	_mix_pool_bytes(utsname(), sizeof(*(utsname())));
+	_mix_pool_bytes(command_line, strlen(command_line));
+	add_latent_entropy();
 
-	if ((fast_pool->count < 64) &&
-	    !time_after(now, fast_pool->last + HZ))
-		return;
-
-	r = &input_pool;
-	if (!spin_trylock(&r->lock))
-		return;
+	if (crng_ready())
+		crng_reseed();
+	else if (trust_cpu)
+		_credit_init_bits(arch_bits);
 
-	fast_pool->last = now;
-	__mix_pool_bytes(r, &fast_pool->pool, sizeof(fast_pool->pool));
-	spin_unlock(&r->lock);
+	return 0;
+}
 
-	fast_pool->count = 0;
+/*
+ * Add device- or boot-specific data to the input pool to help
+ * initialize it.
+ *
+ * None of this adds any entropy; it is meant to avoid the problem of
+ * the entropy pool having similar initial state across largely
+ * identical devices.
+ */
+void add_device_randomness(const void *buf, size_t len)
+{
+	unsigned long entropy = random_get_entropy();
+	unsigned long flags;
 
-	/* award one bit for the contents of the fast pool */
-	credit_entropy_bits(r, 1);
+	spin_lock_irqsave(&input_pool.lock, flags);
+	_mix_pool_bytes(&entropy, sizeof(entropy));
+	_mix_pool_bytes(buf, len);
+	spin_unlock_irqrestore(&input_pool.lock, flags);
 }
-EXPORT_SYMBOL_GPL(add_interrupt_randomness);
+EXPORT_SYMBOL(add_device_randomness);
 
-#ifdef CONFIG_BLOCK
-void add_disk_randomness(struct gendisk *disk)
+/*
+ * Interface for in-kernel drivers of true hardware RNGs.
+ * Those devices may produce endless random bits and will be throttled
+ * when our pool is full.
+ */
+void add_hwgenerator_randomness(const void *buf, size_t len, size_t entropy)
 {
-	if (!disk || !disk->random)
-		return;
-	/* first major is 1, so we get >= 0x200 here */
-	add_timer_randomness(disk->random, 0x100 + disk_devt(disk));
-	trace_add_disk_randomness(disk_devt(disk), ENTROPY_BITS(&input_pool));
-}
-EXPORT_SYMBOL_GPL(add_disk_randomness);
-#endif
+	mix_pool_bytes(buf, len);
+	credit_init_bits(entropy);
 
-/*********************************************************************
- *
- * Entropy extraction routines
- *
- *********************************************************************/
+	/*
+	 * Throttle writing to once every CRNG_RESEED_INTERVAL, unless
+	 * we're not yet initialized.
+	 */
+	if (!kthread_should_stop() && crng_ready())
+		schedule_timeout_interruptible(CRNG_RESEED_INTERVAL);
+}
+EXPORT_SYMBOL_GPL(add_hwgenerator_randomness);
 
 /*
- * This function decides how many bytes to actually take from the
- * given pool, and also debits the entropy count accordingly.
+ * Handle random seed passed by bootloader, and credit it if
+ * CONFIG_RANDOM_TRUST_BOOTLOADER is set.
  */
-static size_t account(struct entropy_store *r, size_t nbytes, int min,
-		      int reserved)
+void __init add_bootloader_randomness(const void *buf, size_t len)
 {
-	int entropy_count, orig, have_bytes;
-	size_t ibytes, nfrac;
+	mix_pool_bytes(buf, len);
+	if (trust_bootloader)
+		credit_init_bits(len * 8);
+}
 
-	BUG_ON(r->entropy_count > r->poolinfo->poolfracbits);
-
-	/* Can we pull enough? */
-retry:
-	entropy_count = orig = READ_ONCE(r->entropy_count);
-	ibytes = nbytes;
-	/* never pull more than available */
-	have_bytes = entropy_count >> (ENTROPY_SHIFT + 3);
-
-	if ((have_bytes -= reserved) < 0)
-		have_bytes = 0;
-	ibytes = min_t(size_t, ibytes, have_bytes);
-	if (ibytes < min)
-		ibytes = 0;
-
-	if (WARN_ON(entropy_count < 0)) {
-		pr_warn("negative entropy count: pool %s count %d\n",
-			r->name, entropy_count);
-		entropy_count = 0;
-	}
-	nfrac = ibytes << (ENTROPY_SHIFT + 3);
-	if ((size_t) entropy_count > nfrac)
-		entropy_count -= nfrac;
-	else
-		entropy_count = 0;
+struct fast_pool {
+	unsigned long pool[4];
+	unsigned long last;
+	unsigned int count;
+	struct timer_list mix;
+};
 
-	if (cmpxchg(&r->entropy_count, orig, entropy_count) != orig)
-		goto retry;
+static void mix_interrupt_randomness(struct timer_list *work);
 
-	trace_debit_entropy(r->name, 8 * ibytes);
-	if (ibytes && ENTROPY_BITS(r) < random_write_wakeup_bits) {
-		wake_up_interruptible(&random_write_wait);
-		kill_fasync(&fasync, SIGIO, POLL_OUT);
-	}
+static DEFINE_PER_CPU(struct fast_pool, irq_randomness) = {
+#ifdef CONFIG_64BIT
+#define FASTMIX_PERM SIPHASH_PERMUTATION
+	.pool = { SIPHASH_CONST_0, SIPHASH_CONST_1, SIPHASH_CONST_2, SIPHASH_CONST_3 },
+#else
+#define FASTMIX_PERM HSIPHASH_PERMUTATION
+	.pool = { HSIPHASH_CONST_0, HSIPHASH_CONST_1, HSIPHASH_CONST_2, HSIPHASH_CONST_3 },
+#endif
+	.mix = __TIMER_INITIALIZER(mix_interrupt_randomness, 0)
+};
 
-	return ibytes;
+/*
+ * This is [Half]SipHash-1-x, starting from an empty key. Because
+ * the key is fixed, it assumes that its inputs are non-malicious,
+ * and therefore this has no security on its own. s represents the
+ * four-word SipHash state, while v represents a two-word input.
+ */
+static void fast_mix(unsigned long s[4], unsigned long v1, unsigned long v2)
+{
+	s[3] ^= v1;
+	FASTMIX_PERM(s[0], s[1], s[2], s[3]);
+	s[0] ^= v1;
+	s[3] ^= v2;
+	FASTMIX_PERM(s[0], s[1], s[2], s[3]);
+	s[0] ^= v2;
 }
 
+#ifdef CONFIG_SMP
 /*
- * This function does the actual extraction for extract_entropy.
- *
- * Note: we assume that .poolwords is a multiple of 16 words.
+ * This function is called when the CPU has just come online, with
+ * entry CPUHP_AP_RANDOM_ONLINE, just after CPUHP_AP_WORKQUEUE_ONLINE.
  */
-static void extract_buf(struct entropy_store *r, __u8 *out)
+int __cold random_online_cpu(unsigned int cpu)
 {
-	int i;
-	union {
-		__u32 w[5];
-		unsigned long l[LONGS(20)];
-	} hash;
-	__u32 workspace[SHA1_WORKSPACE_WORDS];
-	unsigned long flags;
-
 	/*
-	 * If we have an architectural hardware random number
-	 * generator, use it for SHA's initial vector
+	 * During CPU shutdown and before CPU onlining, add_interrupt_
+	 * randomness() may schedule mix_interrupt_randomness(), and
+	 * set the MIX_INFLIGHT flag. However, because the worker can
+	 * be scheduled on a different CPU during this period, that
+	 * flag will never be cleared. For that reason, we zero out
+	 * the flag here, which runs just after workqueues are onlined
+	 * for the CPU again. This also has the effect of setting the
+	 * irq randomness count to zero so that new accumulated irqs
+	 * are fresh.
 	 */
-	sha1_init(hash.w);
-	for (i = 0; i < LONGS(20); i++) {
-		unsigned long v;
-		if (!arch_get_random_long(&v))
-			break;
-		hash.l[i] = v;
-	}
-
-	/* Generate a hash across the pool, 16 words (512 bits) at a time */
-	spin_lock_irqsave(&r->lock, flags);
-	for (i = 0; i < r->poolinfo->poolwords; i += 16)
-		sha1_transform(hash.w, (__u8 *)(r->pool + i), workspace);
+	per_cpu_ptr(&irq_randomness, cpu)->count = 0;
+	return 0;
+}
+#endif
 
+static void mix_interrupt_randomness(struct timer_list *work)
+{
+	struct fast_pool *fast_pool = container_of(work, struct fast_pool, mix);
 	/*
-	 * We mix the hash back into the pool to prevent backtracking
-	 * attacks (where the attacker knows the state of the pool
-	 * plus the current outputs, and attempts to find previous
-	 * ouputs), unless the hash function can be inverted. By
-	 * mixing at least a SHA1 worth of hash data back, we make
-	 * brute-forcing the feedback as hard as brute-forcing the
-	 * hash.
+	 * The size of the copied stack pool is explicitly 2 longs so that we
+	 * only ever ingest half of the siphash output each time, retaining
+	 * the other half as the next "key" that carries over. The entropy is
+	 * supposed to be sufficiently dispersed between bits so on average
+	 * we don't wind up "losing" some.
 	 */
-	__mix_pool_bytes(r, hash.w, sizeof(hash.w));
-	spin_unlock_irqrestore(&r->lock, flags);
+	unsigned long pool[2];
+	unsigned int count;
 
-	memzero_explicit(workspace, sizeof(workspace));
+	/* Check to see if we're running on the wrong CPU due to hotplug. */
+	local_irq_disable();
+	if (fast_pool != this_cpu_ptr(&irq_randomness)) {
+		local_irq_enable();
+		return;
+	}
 
 	/*
-	 * In case the hash function has some recognizable output
-	 * pattern, we fold it in half. Thus, we always feed back
-	 * twice as much data as we output.
+	 * Copy the pool to the stack so that the mixer always has a
+	 * consistent view, before we reenable irqs again.
 	 */
-	hash.w[0] ^= hash.w[3];
-	hash.w[1] ^= hash.w[4];
-	hash.w[2] ^= rol32(hash.w[2], 16);
+	memcpy(pool, fast_pool->pool, sizeof(pool));
+	count = fast_pool->count;
+	fast_pool->count = 0;
+	fast_pool->last = jiffies;
+	local_irq_enable();
+
+	mix_pool_bytes(pool, sizeof(pool));
+	credit_init_bits(clamp_t(unsigned int, (count & U16_MAX) / 64, 1, sizeof(pool) * 8));
 
-	memcpy(out, &hash, EXTRACT_SIZE);
-	memzero_explicit(&hash, sizeof(hash));
+	memzero_explicit(pool, sizeof(pool));
 }
 
-static ssize_t _extract_entropy(struct entropy_store *r, void *buf,
-				size_t nbytes, int fips)
+void add_interrupt_randomness(int irq)
 {
-	ssize_t ret = 0, i;
-	__u8 tmp[EXTRACT_SIZE];
-	unsigned long flags;
+	enum { MIX_INFLIGHT = 1U << 31 };
+	unsigned long entropy = random_get_entropy();
+	struct fast_pool *fast_pool = this_cpu_ptr(&irq_randomness);
+	struct pt_regs *regs = get_irq_regs();
+	unsigned int new_count;
 
-	while (nbytes) {
-		extract_buf(r, tmp);
+	fast_mix(fast_pool->pool, entropy,
+		 (regs ? instruction_pointer(regs) : _RET_IP_) ^ swab(irq));
+	new_count = ++fast_pool->count;
 
-		if (fips) {
-			spin_lock_irqsave(&r->lock, flags);
-			if (!memcmp(tmp, r->last_data, EXTRACT_SIZE))
-				panic("Hardware RNG duplicated output!\n");
-			memcpy(r->last_data, tmp, EXTRACT_SIZE);
-			spin_unlock_irqrestore(&r->lock, flags);
-		}
-		i = min_t(int, nbytes, EXTRACT_SIZE);
-		memcpy(buf, tmp, i);
-		nbytes -= i;
-		buf += i;
-		ret += i;
-	}
+	if (new_count & MIX_INFLIGHT)
+		return;
 
-	/* Wipe data just returned from memory */
-	memzero_explicit(tmp, sizeof(tmp));
+	if (new_count < 1024 && !time_is_before_jiffies(fast_pool->last + HZ))
+		return;
 
-	return ret;
+	fast_pool->count |= MIX_INFLIGHT;
+	if (!timer_pending(&fast_pool->mix)) {
+		fast_pool->mix.expires = jiffies;
+		add_timer_on(&fast_pool->mix, raw_smp_processor_id());
+	}
 }
+EXPORT_SYMBOL_GPL(add_interrupt_randomness);
+
+/* There is one of these per entropy source */
+struct timer_rand_state {
+	unsigned long last_time;
+	long last_delta, last_delta2;
+};
 
 /*
- * This function extracts randomness from the "entropy pool", and
- * returns it in a buffer.
- *
- * The min parameter specifies the minimum amount we can pull before
- * failing to avoid races that defeat catastrophic reseeding while the
- * reserved parameter indicates how much entropy we must leave in the
- * pool after each pull to avoid starving other readers.
+ * This function adds entropy to the entropy "pool" by using timing
+ * delays. It uses the timer_rand_state structure to make an estimate
+ * of how many bits of entropy this call has added to the pool. The
+ * value "num" is also added to the pool; it should somehow describe
+ * the type of event that just happened.
  */
-static ssize_t extract_entropy(struct entropy_store *r, void *buf,
-				 size_t nbytes, int min, int reserved)
+static void add_timer_randomness(struct timer_rand_state *state, unsigned int num)
 {
-	__u8 tmp[EXTRACT_SIZE];
-	unsigned long flags;
+	unsigned long entropy = random_get_entropy(), now = jiffies, flags;
+	long delta, delta2, delta3;
+	unsigned int bits;
 
-	/* if last_data isn't primed, we need EXTRACT_SIZE extra bytes */
-	if (fips_enabled) {
-		spin_lock_irqsave(&r->lock, flags);
-		if (!r->last_data_init) {
-			r->last_data_init = 1;
-			spin_unlock_irqrestore(&r->lock, flags);
-			trace_extract_entropy(r->name, EXTRACT_SIZE,
-					      ENTROPY_BITS(r), _RET_IP_);
-			extract_buf(r, tmp);
-			spin_lock_irqsave(&r->lock, flags);
-			memcpy(r->last_data, tmp, EXTRACT_SIZE);
-		}
-		spin_unlock_irqrestore(&r->lock, flags);
+	/*
+	 * If we're in a hard IRQ, add_interrupt_randomness() will be called
+	 * sometime after, so mix into the fast pool.
+	 */
+	if (in_hardirq()) {
+		fast_mix(this_cpu_ptr(&irq_randomness)->pool, entropy, num);
+	} else {
+		spin_lock_irqsave(&input_pool.lock, flags);
+		_mix_pool_bytes(&entropy, sizeof(entropy));
+		_mix_pool_bytes(&num, sizeof(num));
+		spin_unlock_irqrestore(&input_pool.lock, flags);
 	}
 
-	trace_extract_entropy(r->name, nbytes, ENTROPY_BITS(r), _RET_IP_);
-	nbytes = account(r, nbytes, min, reserved);
+	if (crng_ready())
+		return;
 
-	return _extract_entropy(r, buf, nbytes, fips_enabled);
-}
+	/*
+	 * Calculate number of bits of randomness we probably added.
+	 * We take into account the first, second and third-order deltas
+	 * in order to make our estimate.
+	 */
+	delta = now - READ_ONCE(state->last_time);
+	WRITE_ONCE(state->last_time, now);
 
-#define warn_unseeded_randomness(previous) \
-	_warn_unseeded_randomness(__func__, (void *) _RET_IP_, (previous))
+	delta2 = delta - READ_ONCE(state->last_delta);
+	WRITE_ONCE(state->last_delta, delta);
 
-static void _warn_unseeded_randomness(const char *func_name, void *caller,
-				      void **previous)
-{
-#ifdef CONFIG_WARN_ALL_UNSEEDED_RANDOM
-	const bool print_once = false;
-#else
-	static bool print_once __read_mostly;
-#endif
+	delta3 = delta2 - READ_ONCE(state->last_delta2);
+	WRITE_ONCE(state->last_delta2, delta2);
 
-	if (print_once ||
-	    crng_ready() ||
-	    (previous && (caller == READ_ONCE(*previous))))
-		return;
-	WRITE_ONCE(*previous, caller);
-#ifndef CONFIG_WARN_ALL_UNSEEDED_RANDOM
-	print_once = true;
-#endif
-	if (__ratelimit(&unseeded_warning))
-		printk_deferred(KERN_NOTICE "random: %s called from %pS "
-				"with crng_init=%d\n", func_name, caller,
-				crng_init);
+	if (delta < 0)
+		delta = -delta;
+	if (delta2 < 0)
+		delta2 = -delta2;
+	if (delta3 < 0)
+		delta3 = -delta3;
+	if (delta > delta2)
+		delta = delta2;
+	if (delta > delta3)
+		delta = delta3;
+
+	/*
+	 * delta is now minimum absolute delta. Round down by 1 bit
+	 * on general principles, and limit entropy estimate to 11 bits.
+	 */
+	bits = min(fls(delta >> 1), 11);
+
+	/*
+	 * As mentioned above, if we're in a hard IRQ, add_interrupt_randomness()
+	 * will run after this, which uses a different crediting scheme of 1 bit
+	 * per every 64 interrupts. In order to let that function do accounting
+	 * close to the one in this function, we credit a full 64/64 bit per bit,
+	 * and then subtract one to account for the extra one added.
+	 */
+	if (in_hardirq())
+		this_cpu_ptr(&irq_randomness)->count += max(1u, bits * 64) - 1;
+	else
+		_credit_init_bits(bits);
 }
 
-/*
- * This function is the exported kernel interface.  It returns some
- * number of good random numbers, suitable for key generation, seeding
- * TCP sequence numbers, etc.  It does not rely on the hardware random
- * number generator.  For random bytes direct from the hardware RNG
- * (when available), use get_random_bytes_arch(). In order to ensure
- * that the randomness provided by this function is okay, the function
- * wait_for_random_bytes() should be called and return 0 at least once
- * at any point prior.
- */
-static void _get_random_bytes(void *buf, int nbytes)
+void add_input_randomness(unsigned int type, unsigned int code, unsigned int value)
 {
-	__u8 tmp[CHACHA_BLOCK_SIZE] __aligned(4);
+	static unsigned char last_value;
+	static struct timer_rand_state input_timer_state = { INITIAL_JIFFIES };
 
-	trace_get_random_bytes(nbytes, _RET_IP_);
+	/* Ignore autorepeat and the like. */
+	if (value == last_value)
+		return;
 
-	while (nbytes >= CHACHA_BLOCK_SIZE) {
-		extract_crng(buf);
-		buf += CHACHA_BLOCK_SIZE;
-		nbytes -= CHACHA_BLOCK_SIZE;
-	}
+	last_value = value;
+	add_timer_randomness(&input_timer_state,
+			     (type << 4) ^ code ^ (code >> 4) ^ value);
+}
+EXPORT_SYMBOL_GPL(add_input_randomness);
 
-	if (nbytes > 0) {
-		extract_crng(tmp);
-		memcpy(buf, tmp, nbytes);
-		crng_backtrack_protect(tmp, nbytes);
-	} else
-		crng_backtrack_protect(tmp, CHACHA_BLOCK_SIZE);
-	memzero_explicit(tmp, sizeof(tmp));
+#ifdef CONFIG_BLOCK
+void add_disk_randomness(struct gendisk *disk)
+{
+	if (!disk || !disk->random)
+		return;
+	/* First major is 1, so we get >= 0x200 here. */
+	add_timer_randomness(disk->random, 0x100 + disk_devt(disk));
 }
+EXPORT_SYMBOL_GPL(add_disk_randomness);
 
-void get_random_bytes(void *buf, int nbytes)
+void __cold rand_initialize_disk(struct gendisk *disk)
 {
-	static void *previous;
+	struct timer_rand_state *state;
 
-	warn_unseeded_randomness(&previous);
-	_get_random_bytes(buf, nbytes);
+	/*
+	 * If kzalloc returns null, we just won't use that entropy
+	 * source.
+	 */
+	state = kzalloc(sizeof(struct timer_rand_state), GFP_KERNEL);
+	if (state) {
+		state->last_time = INITIAL_JIFFIES;
+		disk->random = state;
+	}
 }
-EXPORT_SYMBOL(get_random_bytes);
-
+#endif
 
 /*
  * Each time the timer fires, we expect that we got an unpredictable
@@ -1566,351 +1147,181 @@
  *
  * So the re-arming always happens in the entropy loop itself.
  */
-static void entropy_timer(struct timer_list *t)
+static void __cold entropy_timer(struct timer_list *t)
 {
-	credit_entropy_bits(&input_pool, 1);
+	credit_init_bits(1);
 }
 
 /*
  * If we have an actual cycle counter, see if we can
  * generate enough entropy with timing noise
  */
-static void try_to_generate_entropy(void)
+static void __cold try_to_generate_entropy(void)
 {
 	struct {
-		unsigned long now;
+		unsigned long entropy;
 		struct timer_list timer;
 	} stack;
 
-	stack.now = random_get_entropy();
+	stack.entropy = random_get_entropy();
 
 	/* Slow counter - or none. Don't even bother */
-	if (stack.now == random_get_entropy())
+	if (stack.entropy == random_get_entropy())
 		return;
 
 	timer_setup_on_stack(&stack.timer, entropy_timer, 0);
-	while (!crng_ready()) {
+	while (!crng_ready() && !signal_pending(current)) {
 		if (!timer_pending(&stack.timer))
-			mod_timer(&stack.timer, jiffies+1);
-		mix_pool_bytes(&input_pool, &stack.now, sizeof(stack.now));
+			mod_timer(&stack.timer, jiffies + 1);
+		mix_pool_bytes(&stack.entropy, sizeof(stack.entropy));
 		schedule();
-		stack.now = random_get_entropy();
+		stack.entropy = random_get_entropy();
 	}
 
 	del_timer_sync(&stack.timer);
 	destroy_timer_on_stack(&stack.timer);
-	mix_pool_bytes(&input_pool, &stack.now, sizeof(stack.now));
+	mix_pool_bytes(&stack.entropy, sizeof(stack.entropy));
 }
 
-/*
- * Wait for the urandom pool to be seeded and thus guaranteed to supply
- * cryptographically secure random numbers. This applies to: the /dev/urandom
- * device, the get_random_bytes function, and the get_random_{u32,u64,int,long}
- * family of functions. Using any of these functions without first calling
- * this function forfeits the guarantee of security.
- *
- * Returns: 0 if the urandom pool has been seeded.
- *          -ERESTARTSYS if the function was interrupted by a signal.
- */
-int wait_for_random_bytes(void)
-{
-	if (likely(crng_ready()))
-		return 0;
-
-	do {
-		int ret;
-		ret = wait_event_interruptible_timeout(crng_init_wait, crng_ready(), HZ);
-		if (ret)
-			return ret > 0 ? 0 : ret;
-
-		try_to_generate_entropy();
-	} while (!crng_ready());
-
-	return 0;
-}
-EXPORT_SYMBOL(wait_for_random_bytes);
 
-/*
- * Returns whether or not the urandom pool has been seeded and thus guaranteed
- * to supply cryptographically secure random numbers. This applies to: the
- * /dev/urandom device, the get_random_bytes function, and the get_random_{u32,
- * ,u64,int,long} family of functions.
+/**********************************************************************
  *
- * Returns: true if the urandom pool has been seeded.
- *          false if the urandom pool has not been seeded.
- */
-bool rng_is_initialized(void)
-{
-	return crng_ready();
-}
-EXPORT_SYMBOL(rng_is_initialized);
-
-/*
- * Add a callback function that will be invoked when the nonblocking
- * pool is initialised.
+ * Userspace reader/writer interfaces.
  *
- * returns: 0 if callback is successfully added
- *	    -EALREADY if pool is already initialised (callback not called)
- *	    -ENOENT if module for callback is not alive
- */
-int add_random_ready_callback(struct random_ready_callback *rdy)
-{
-	struct module *owner;
-	unsigned long flags;
-	int err = -EALREADY;
-
-	if (crng_ready())
-		return err;
-
-	owner = rdy->owner;
-	if (!try_module_get(owner))
-		return -ENOENT;
-
-	spin_lock_irqsave(&random_ready_list_lock, flags);
-	if (crng_ready())
-		goto out;
+ * getrandom(2) is the primary modern interface into the RNG and should
+ * be used in preference to anything else.
+ *
+ * Reading from /dev/random has the same functionality as calling
+ * getrandom(2) with flags=0. In earlier versions, however, it had
+ * vastly different semantics and should therefore be avoided, to
+ * prevent backwards compatibility issues.
+ *
+ * Reading from /dev/urandom has the same functionality as calling
+ * getrandom(2) with flags=GRND_INSECURE. Because it does not block
+ * waiting for the RNG to be ready, it should not be used.
+ *
+ * Writing to either /dev/random or /dev/urandom adds entropy to
+ * the input pool but does not credit it.
+ *
+ * Polling on /dev/random indicates when the RNG is initialized, on
+ * the read side, and when it wants new entropy, on the write side.
+ *
+ * Both /dev/random and /dev/urandom have the same set of ioctls for
+ * adding entropy, getting the entropy count, zeroing the count, and
+ * reseeding the crng.
+ *
+ **********************************************************************/
 
-	owner = NULL;
+SYSCALL_DEFINE3(getrandom, char __user *, ubuf, size_t, len, unsigned int, flags)
+{
+	struct iov_iter iter;
+	struct iovec iov;
+	int ret;
 
-	list_add(&rdy->list, &random_ready_list);
-	err = 0;
+	if (flags & ~(GRND_NONBLOCK | GRND_RANDOM | GRND_INSECURE))
+		return -EINVAL;
 
-out:
-	spin_unlock_irqrestore(&random_ready_list_lock, flags);
+	/*
+	 * Requesting insecure and blocking randomness at the same time makes
+	 * no sense.
+	 */
+	if ((flags & (GRND_INSECURE | GRND_RANDOM)) == (GRND_INSECURE | GRND_RANDOM))
+		return -EINVAL;
 
-	module_put(owner);
+	if (!crng_ready() && !(flags & GRND_INSECURE)) {
+		if (flags & GRND_NONBLOCK)
+			return -EAGAIN;
+		ret = wait_for_random_bytes();
+		if (unlikely(ret))
+			return ret;
+	}
 
-	return err;
+	ret = import_single_range(READ, ubuf, len, &iov, &iter);
+	if (unlikely(ret))
+		return ret;
+	return get_random_bytes_user(&iter);
 }
-EXPORT_SYMBOL(add_random_ready_callback);
 
-/*
- * Delete a previously registered readiness callback function.
- */
-void del_random_ready_callback(struct random_ready_callback *rdy)
+static __poll_t random_poll(struct file *file, poll_table *wait)
 {
-	unsigned long flags;
-	struct module *owner = NULL;
-
-	spin_lock_irqsave(&random_ready_list_lock, flags);
-	if (!list_empty(&rdy->list)) {
-		list_del_init(&rdy->list);
-		owner = rdy->owner;
-	}
-	spin_unlock_irqrestore(&random_ready_list_lock, flags);
-
-	module_put(owner);
+	poll_wait(file, &crng_init_wait, wait);
+	return crng_ready() ? EPOLLIN | EPOLLRDNORM : EPOLLOUT | EPOLLWRNORM;
 }
-EXPORT_SYMBOL(del_random_ready_callback);
 
-/*
- * This function will use the architecture-specific hardware random
- * number generator if it is available.  The arch-specific hw RNG will
- * almost certainly be faster than what we can do in software, but it
- * is impossible to verify that it is implemented securely (as
- * opposed, to, say, the AES encryption of a sequence number using a
- * key known by the NSA).  So it's useful if we need the speed, but
- * only if we're willing to trust the hardware manufacturer not to
- * have put in a back door.
- *
- * Return number of bytes filled in.
- */
-int __must_check get_random_bytes_arch(void *buf, int nbytes)
+static ssize_t write_pool_user(struct iov_iter *iter)
 {
-	int left = nbytes;
-	char *p = buf;
+	u8 block[BLAKE2S_BLOCK_SIZE];
+	ssize_t ret = 0;
+	size_t copied;
 
-	trace_get_random_bytes_arch(left, _RET_IP_);
-	while (left) {
-		unsigned long v;
-		int chunk = min_t(int, left, sizeof(unsigned long));
+	if (unlikely(!iov_iter_count(iter)))
+		return 0;
 
-		if (!arch_get_random_long(&v))
+	for (;;) {
+		copied = copy_from_iter(block, sizeof(block), iter);
+		ret += copied;
+		mix_pool_bytes(block, copied);
+		if (!iov_iter_count(iter) || copied != sizeof(block))
 			break;
 
-		memcpy(p, &v, chunk);
-		p += chunk;
-		left -= chunk;
-	}
-
-	return nbytes - left;
-}
-EXPORT_SYMBOL(get_random_bytes_arch);
-
-/*
- * init_std_data - initialize pool with system data
- *
- * @r: pool to initialize
- *
- * This function clears the pool's entropy count and mixes some system
- * data into the pool to prepare it for use. The pool is not cleared
- * as that can only decrease the entropy in the pool.
- */
-static void __init init_std_data(struct entropy_store *r)
-{
-	int i;
-	ktime_t now = ktime_get_real();
-	unsigned long rv;
-
-	mix_pool_bytes(r, &now, sizeof(now));
-	for (i = r->poolinfo->poolbytes; i > 0; i -= sizeof(rv)) {
-		if (!arch_get_random_seed_long(&rv) &&
-		    !arch_get_random_long(&rv))
-			rv = random_get_entropy();
-		mix_pool_bytes(r, &rv, sizeof(rv));
-	}
-	mix_pool_bytes(r, utsname(), sizeof(*(utsname())));
-}
-
-/*
- * Note that setup_arch() may call add_device_randomness()
- * long before we get here. This allows seeding of the pools
- * with some platform dependent data very early in the boot
- * process. But it limits our options here. We must use
- * statically allocated structures that already have all
- * initializations complete at compile time. We should also
- * take care not to overwrite the precious per platform data
- * we were given.
- */
-int __init rand_initialize(void)
-{
-	init_std_data(&input_pool);
-	crng_initialize_primary(&primary_crng);
-	crng_global_init_time = jiffies;
-	if (ratelimit_disable) {
-		urandom_warning.interval = 0;
-		unseeded_warning.interval = 0;
+		BUILD_BUG_ON(PAGE_SIZE % sizeof(block) != 0);
+		if (ret % PAGE_SIZE == 0) {
+			if (signal_pending(current))
+				break;
+			cond_resched();
+		}
 	}
-	return 0;
-}
-
-#ifdef CONFIG_BLOCK
-void rand_initialize_disk(struct gendisk *disk)
-{
-	struct timer_rand_state *state;
 
-	/*
-	 * If kzalloc returns null, we just won't use that entropy
-	 * source.
-	 */
-	state = kzalloc(sizeof(struct timer_rand_state), GFP_KERNEL);
-	if (state) {
-		state->last_time = INITIAL_JIFFIES;
-		disk->random = state;
-	}
+	memzero_explicit(block, sizeof(block));
+	return ret ? ret : -EFAULT;
 }
-#endif
 
-static ssize_t
-urandom_read_nowarn(struct file *file, char __user *buf, size_t nbytes,
-		    loff_t *ppos)
+static ssize_t random_write_iter(struct kiocb *kiocb, struct iov_iter *iter)
 {
-	int ret;
-
-	nbytes = min_t(size_t, nbytes, INT_MAX >> (ENTROPY_SHIFT + 3));
-	ret = extract_crng_user(buf, nbytes);
-	trace_urandom_read(8 * nbytes, 0, ENTROPY_BITS(&input_pool));
-	return ret;
+	return write_pool_user(iter);
 }
 
-static ssize_t
-urandom_read(struct file *file, char __user *buf, size_t nbytes, loff_t *ppos)
+static ssize_t urandom_read_iter(struct kiocb *kiocb, struct iov_iter *iter)
 {
-	unsigned long flags;
 	static int maxwarn = 10;
 
-	if (!crng_ready() && maxwarn > 0) {
-		maxwarn--;
-		if (__ratelimit(&urandom_warning))
-			pr_notice("%s: uninitialized urandom read (%zd bytes read)\n",
-				  current->comm, nbytes);
-		spin_lock_irqsave(&primary_crng.lock, flags);
-		crng_init_cnt = 0;
-		spin_unlock_irqrestore(&primary_crng.lock, flags);
+	if (!crng_ready()) {
+		if (!ratelimit_disable && maxwarn <= 0)
+			++urandom_warning.missed;
+		else if (ratelimit_disable || __ratelimit(&urandom_warning)) {
+			--maxwarn;
+			pr_notice("%s: uninitialized urandom read (%zu bytes read)\n",
+				  current->comm, iov_iter_count(iter));
+		}
 	}
 
-	return urandom_read_nowarn(file, buf, nbytes, ppos);
+	return get_random_bytes_user(iter);
 }
 
-static ssize_t
-random_read(struct file *file, char __user *buf, size_t nbytes, loff_t *ppos)
+static ssize_t random_read_iter(struct kiocb *kiocb, struct iov_iter *iter)
 {
 	int ret;
 
+	if (!crng_ready() &&
+	    ((kiocb->ki_flags & (IOCB_NOWAIT | IOCB_NOIO)) ||
+	     (kiocb->ki_filp->f_flags & O_NONBLOCK)))
+		return -EAGAIN;
+
 	ret = wait_for_random_bytes();
 	if (ret != 0)
 		return ret;
-	return urandom_read_nowarn(file, buf, nbytes, ppos);
-}
-
-static __poll_t
-random_poll(struct file *file, poll_table * wait)
-{
-	__poll_t mask;
-
-	poll_wait(file, &crng_init_wait, wait);
-	poll_wait(file, &random_write_wait, wait);
-	mask = 0;
-	if (crng_ready())
-		mask |= EPOLLIN | EPOLLRDNORM;
-	if (ENTROPY_BITS(&input_pool) < random_write_wakeup_bits)
-		mask |= EPOLLOUT | EPOLLWRNORM;
-	return mask;
-}
-
-static int
-write_pool(struct entropy_store *r, const char __user *buffer, size_t count)
-{
-	size_t bytes;
-	__u32 t, buf[16];
-	const char __user *p = buffer;
-
-	while (count > 0) {
-		int b, i = 0;
-
-		bytes = min(count, sizeof(buf));
-		if (copy_from_user(&buf, p, bytes))
-			return -EFAULT;
-
-		for (b = bytes ; b > 0 ; b -= sizeof(__u32), i++) {
-			if (!arch_get_random_int(&t))
-				break;
-			buf[i] ^= t;
-		}
-
-		count -= bytes;
-		p += bytes;
-
-		mix_pool_bytes(r, buf, bytes);
-		cond_resched();
-	}
-
-	return 0;
-}
-
-static ssize_t random_write(struct file *file, const char __user *buffer,
-			    size_t count, loff_t *ppos)
-{
-	size_t ret;
-
-	ret = write_pool(&input_pool, buffer, count);
-	if (ret)
-		return ret;
-
-	return (ssize_t)count;
+	return get_random_bytes_user(iter);
 }
 
 static long random_ioctl(struct file *f, unsigned int cmd, unsigned long arg)
 {
-	int size, ent_count;
 	int __user *p = (int __user *)arg;
-	int retval;
+	int ent_count;
 
 	switch (cmd) {
 	case RNDGETENTCNT:
-		/* inherently racy, no point locking */
-		ent_count = ENTROPY_BITS(&input_pool);
-		if (put_user(ent_count, p))
+		/* Inherently racy, no point locking. */
+		if (put_user(input_pool.init_bits, p))
 			return -EFAULT;
 		return 0;
 	case RNDADDTOENTCNT:
@@ -1918,38 +1329,48 @@
 			return -EPERM;
 		if (get_user(ent_count, p))
 			return -EFAULT;
-		return credit_entropy_bits_safe(&input_pool, ent_count);
-	case RNDADDENTROPY:
+		if (ent_count < 0)
+			return -EINVAL;
+		credit_init_bits(ent_count);
+		return 0;
+	case RNDADDENTROPY: {
+		struct iov_iter iter;
+		struct iovec iov;
+		ssize_t ret;
+		int len;
+
 		if (!capable(CAP_SYS_ADMIN))
 			return -EPERM;
 		if (get_user(ent_count, p++))
 			return -EFAULT;
 		if (ent_count < 0)
 			return -EINVAL;
-		if (get_user(size, p++))
+		if (get_user(len, p++))
+			return -EFAULT;
+		ret = import_single_range(WRITE, p, len, &iov, &iter);
+		if (unlikely(ret))
+			return ret;
+		ret = write_pool_user(&iter);
+		if (unlikely(ret < 0))
+			return ret;
+		/* Since we're crediting, enforce that it was all written into the pool. */
+		if (unlikely(ret != len))
 			return -EFAULT;
-		retval = write_pool(&input_pool, (const char __user *)p,
-				    size);
-		if (retval < 0)
-			return retval;
-		return credit_entropy_bits_safe(&input_pool, ent_count);
+		credit_init_bits(ent_count);
+		return 0;
+	}
 	case RNDZAPENTCNT:
 	case RNDCLEARPOOL:
-		/*
-		 * Clear the entropy pool counters. We no longer clear
-		 * the entropy pool, as that's silly.
-		 */
+		/* No longer has any effect. */
 		if (!capable(CAP_SYS_ADMIN))
 			return -EPERM;
-		input_pool.entropy_count = 0;
 		return 0;
 	case RNDRESEEDCRNG:
 		if (!capable(CAP_SYS_ADMIN))
 			return -EPERM;
-		if (crng_init < 2)
+		if (!crng_ready())
 			return -ENODATA;
-		crng_reseed(&primary_crng, &input_pool);
-		crng_global_init_time = jiffies - 1;
+		crng_reseed();
 		return 0;
 	default:
 		return -EINVAL;
@@ -1962,55 +1383,56 @@
 }
 
 const struct file_operations random_fops = {
-	.read  = random_read,
-	.write = random_write,
-	.poll  = random_poll,
+	.read_iter = random_read_iter,
+	.write_iter = random_write_iter,
+	.poll = random_poll,
 	.unlocked_ioctl = random_ioctl,
 	.compat_ioctl = compat_ptr_ioctl,
 	.fasync = random_fasync,
 	.llseek = noop_llseek,
+	.splice_read = generic_file_splice_read,
+	.splice_write = iter_file_splice_write,
 };
 
 const struct file_operations urandom_fops = {
-	.read  = urandom_read,
-	.write = random_write,
+	.read_iter = urandom_read_iter,
+	.write_iter = random_write_iter,
 	.unlocked_ioctl = random_ioctl,
 	.compat_ioctl = compat_ptr_ioctl,
 	.fasync = random_fasync,
 	.llseek = noop_llseek,
+	.splice_read = generic_file_splice_read,
+	.splice_write = iter_file_splice_write,
 };
 
-SYSCALL_DEFINE3(getrandom, char __user *, buf, size_t, count,
-		unsigned int, flags)
-{
-	int ret;
-
-	if (flags & ~(GRND_NONBLOCK|GRND_RANDOM|GRND_INSECURE))
-		return -EINVAL;
-
-	/*
-	 * Requesting insecure and blocking randomness at the same time makes
-	 * no sense.
-	 */
-	if ((flags & (GRND_INSECURE|GRND_RANDOM)) == (GRND_INSECURE|GRND_RANDOM))
-		return -EINVAL;
-
-	if (count > INT_MAX)
-		count = INT_MAX;
-
-	if (!(flags & GRND_INSECURE) && !crng_ready()) {
-		if (flags & GRND_NONBLOCK)
-			return -EAGAIN;
-		ret = wait_for_random_bytes();
-		if (unlikely(ret))
-			return ret;
-	}
-	return urandom_read_nowarn(NULL, buf, count, NULL);
-}
 
 /********************************************************************
  *
- * Sysctl interface
+ * Sysctl interface.
+ *
+ * These are partly unused legacy knobs with dummy values to not break
+ * userspace and partly still useful things. They are usually accessible
+ * in /proc/sys/kernel/random/ and are as follows:
+ *
+ * - boot_id - a UUID representing the current boot.
+ *
+ * - uuid - a random UUID, different each time the file is read.
+ *
+ * - poolsize - the number of bits of entropy that the input pool can
+ *   hold, tied to the POOL_BITS constant.
+ *
+ * - entropy_avail - the number of bits of entropy currently in the
+ *   input pool. Always <= poolsize.
+ *
+ * - write_wakeup_threshold - the amount of entropy in the input pool
+ *   below which write polls to /dev/random will unblock, requesting
+ *   more entropy, tied to the POOL_READY_BITS constant. It is writable
+ *   to avoid breaking old userspaces, but writing to it does not
+ *   change any behavior of the RNG.
+ *
+ * - urandom_min_reseed_secs - fixed to the value CRNG_RESEED_INTERVAL.
+ *   It is writable to avoid breaking old userspaces, but writing
+ *   to it does not change any behavior of the RNG.
  *
  ********************************************************************/
 
@@ -2018,25 +1440,28 @@
 
 #include <linux/sysctl.h>
 
-static int min_write_thresh;
-static int max_write_thresh = INPUT_POOL_WORDS * 32;
-static int random_min_urandom_seed = 60;
-static char sysctl_bootid[16];
+static int sysctl_random_min_urandom_seed = CRNG_RESEED_INTERVAL / HZ;
+static int sysctl_random_write_wakeup_bits = POOL_READY_BITS;
+static int sysctl_poolsize = POOL_BITS;
+static u8 sysctl_bootid[UUID_SIZE];
 
 /*
  * This function is used to return both the bootid UUID, and random
- * UUID.  The difference is in whether table->data is NULL; if it is,
+ * UUID. The difference is in whether table->data is NULL; if it is,
  * then a new UUID is generated and returned to the user.
- *
- * If the user accesses this via the proc interface, the UUID will be
- * returned as an ASCII string in the standard UUID format; if via the
- * sysctl system call, as 16 bytes of binary data.
  */
-static int proc_do_uuid(struct ctl_table *table, int write,
-			void *buffer, size_t *lenp, loff_t *ppos)
+static int proc_do_uuid(struct ctl_table *table, int write, void *buf,
+			size_t *lenp, loff_t *ppos)
 {
-	struct ctl_table fake_table;
-	unsigned char buf[64], tmp_uuid[16], *uuid;
+	u8 tmp_uuid[UUID_SIZE], *uuid;
+	char uuid_string[UUID_STRING_LEN + 1];
+	struct ctl_table fake_table = {
+		.data = uuid_string,
+		.maxlen = UUID_STRING_LEN
+	};
+
+	if (write)
+		return -EPERM;
 
 	uuid = table->data;
 	if (!uuid) {
@@ -2051,32 +1476,17 @@
 		spin_unlock(&bootid_spinlock);
 	}
 
-	sprintf(buf, "%pU", uuid);
-
-	fake_table.data = buf;
-	fake_table.maxlen = sizeof(buf);
-
-	return proc_dostring(&fake_table, write, buffer, lenp, ppos);
+	snprintf(uuid_string, sizeof(uuid_string), "%pU", uuid);
+	return proc_dostring(&fake_table, 0, buf, lenp, ppos);
 }
 
-/*
- * Return entropy available scaled to integral bits
- */
-static int proc_do_entropy(struct ctl_table *table, int write,
-			   void *buffer, size_t *lenp, loff_t *ppos)
+/* The same as proc_dointvec, but writes don't change anything. */
+static int proc_do_rointvec(struct ctl_table *table, int write, void *buf,
+			    size_t *lenp, loff_t *ppos)
 {
-	struct ctl_table fake_table;
-	int entropy_count;
-
-	entropy_count = *(int *)table->data >> ENTROPY_SHIFT;
-
-	fake_table.data = &entropy_count;
-	fake_table.maxlen = sizeof(entropy_count);
-
-	return proc_dointvec(&fake_table, write, buffer, lenp, ppos);
+	return write ? 0 : proc_dointvec(table, 0, buf, lenp, ppos);
 }
 
-static int sysctl_poolsize = INPUT_POOL_WORDS * 32;
 extern struct ctl_table random_table[];
 struct ctl_table random_table[] = {
 	{
@@ -2088,218 +1498,36 @@
 	},
 	{
 		.procname	= "entropy_avail",
+		.data		= &input_pool.init_bits,
 		.maxlen		= sizeof(int),
 		.mode		= 0444,
-		.proc_handler	= proc_do_entropy,
-		.data		= &input_pool.entropy_count,
+		.proc_handler	= proc_dointvec,
 	},
 	{
 		.procname	= "write_wakeup_threshold",
-		.data		= &random_write_wakeup_bits,
+		.data		= &sysctl_random_write_wakeup_bits,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &min_write_thresh,
-		.extra2		= &max_write_thresh,
+		.proc_handler	= proc_do_rointvec,
 	},
 	{
 		.procname	= "urandom_min_reseed_secs",
-		.data		= &random_min_urandom_seed,
+		.data		= &sysctl_random_min_urandom_seed,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_dointvec,
+		.proc_handler	= proc_do_rointvec,
 	},
 	{
 		.procname	= "boot_id",
 		.data		= &sysctl_bootid,
-		.maxlen		= 16,
 		.mode		= 0444,
 		.proc_handler	= proc_do_uuid,
 	},
 	{
 		.procname	= "uuid",
-		.maxlen		= 16,
 		.mode		= 0444,
 		.proc_handler	= proc_do_uuid,
 	},
-#ifdef ADD_INTERRUPT_BENCH
-	{
-		.procname	= "add_interrupt_avg_cycles",
-		.data		= &avg_cycles,
-		.maxlen		= sizeof(avg_cycles),
-		.mode		= 0444,
-		.proc_handler	= proc_doulongvec_minmax,
-	},
-	{
-		.procname	= "add_interrupt_avg_deviation",
-		.data		= &avg_deviation,
-		.maxlen		= sizeof(avg_deviation),
-		.mode		= 0444,
-		.proc_handler	= proc_doulongvec_minmax,
-	},
-#endif
 	{ }
 };
-#endif 	/* CONFIG_SYSCTL */
-
-struct batched_entropy {
-	union {
-		u64 entropy_u64[CHACHA_BLOCK_SIZE / sizeof(u64)];
-		u32 entropy_u32[CHACHA_BLOCK_SIZE / sizeof(u32)];
-	};
-	unsigned int position;
-	spinlock_t batch_lock;
-};
-
-/*
- * Get a random word for internal kernel use only. The quality of the random
- * number is good as /dev/urandom, but there is no backtrack protection, with
- * the goal of being quite fast and not depleting entropy. In order to ensure
- * that the randomness provided by this function is okay, the function
- * wait_for_random_bytes() should be called and return 0 at least once at any
- * point prior.
- */
-static DEFINE_PER_CPU(struct batched_entropy, batched_entropy_u64) = {
-	.batch_lock	= __SPIN_LOCK_UNLOCKED(batched_entropy_u64.lock),
-};
-
-u64 get_random_u64(void)
-{
-	u64 ret;
-	unsigned long flags;
-	struct batched_entropy *batch;
-	static void *previous;
-
-	warn_unseeded_randomness(&previous);
-
-	batch = raw_cpu_ptr(&batched_entropy_u64);
-	spin_lock_irqsave(&batch->batch_lock, flags);
-	if (batch->position % ARRAY_SIZE(batch->entropy_u64) == 0) {
-		extract_crng((u8 *)batch->entropy_u64);
-		batch->position = 0;
-	}
-	ret = batch->entropy_u64[batch->position++];
-	spin_unlock_irqrestore(&batch->batch_lock, flags);
-	return ret;
-}
-EXPORT_SYMBOL(get_random_u64);
-
-static DEFINE_PER_CPU(struct batched_entropy, batched_entropy_u32) = {
-	.batch_lock	= __SPIN_LOCK_UNLOCKED(batched_entropy_u32.lock),
-};
-u32 get_random_u32(void)
-{
-	u32 ret;
-	unsigned long flags;
-	struct batched_entropy *batch;
-	static void *previous;
-
-	warn_unseeded_randomness(&previous);
-
-	batch = raw_cpu_ptr(&batched_entropy_u32);
-	spin_lock_irqsave(&batch->batch_lock, flags);
-	if (batch->position % ARRAY_SIZE(batch->entropy_u32) == 0) {
-		extract_crng((u8 *)batch->entropy_u32);
-		batch->position = 0;
-	}
-	ret = batch->entropy_u32[batch->position++];
-	spin_unlock_irqrestore(&batch->batch_lock, flags);
-	return ret;
-}
-EXPORT_SYMBOL(get_random_u32);
-
-/* It's important to invalidate all potential batched entropy that might
- * be stored before the crng is initialized, which we can do lazily by
- * simply resetting the counter to zero so that it's re-extracted on the
- * next usage. */
-static void invalidate_batched_entropy(void)
-{
-	int cpu;
-	unsigned long flags;
-
-	for_each_possible_cpu (cpu) {
-		struct batched_entropy *batched_entropy;
-
-		batched_entropy = per_cpu_ptr(&batched_entropy_u32, cpu);
-		spin_lock_irqsave(&batched_entropy->batch_lock, flags);
-		batched_entropy->position = 0;
-		spin_unlock(&batched_entropy->batch_lock);
-
-		batched_entropy = per_cpu_ptr(&batched_entropy_u64, cpu);
-		spin_lock(&batched_entropy->batch_lock);
-		batched_entropy->position = 0;
-		spin_unlock_irqrestore(&batched_entropy->batch_lock, flags);
-	}
-}
-
-/**
- * randomize_page - Generate a random, page aligned address
- * @start:	The smallest acceptable address the caller will take.
- * @range:	The size of the area, starting at @start, within which the
- *		random address must fall.
- *
- * If @start + @range would overflow, @range is capped.
- *
- * NOTE: Historical use of randomize_range, which this replaces, presumed that
- * @start was already page aligned.  We now align it regardless.
- *
- * Return: A page aligned address within [start, start + range).  On error,
- * @start is returned.
- */
-unsigned long
-randomize_page(unsigned long start, unsigned long range)
-{
-	if (!PAGE_ALIGNED(start)) {
-		range -= PAGE_ALIGN(start) - start;
-		start = PAGE_ALIGN(start);
-	}
-
-	if (start > ULONG_MAX - range)
-		range = ULONG_MAX - start;
-
-	range >>= PAGE_SHIFT;
-
-	if (range == 0)
-		return start;
-
-	return start + (get_random_long() % range << PAGE_SHIFT);
-}
-
-/* Interface for in-kernel drivers of true hardware RNGs.
- * Those devices may produce endless random bits and will be throttled
- * when our pool is full.
- */
-void add_hwgenerator_randomness(const char *buffer, size_t count,
-				size_t entropy)
-{
-	struct entropy_store *poolp = &input_pool;
-
-	if (unlikely(crng_init == 0)) {
-		crng_fast_load(buffer, count);
-		return;
-	}
-
-	/* Suspend writing if we're above the trickle threshold.
-	 * We'll be woken up again once below random_write_wakeup_thresh,
-	 * or when the calling thread is about to terminate.
-	 */
-	wait_event_interruptible(random_write_wait, kthread_should_stop() ||
-			ENTROPY_BITS(&input_pool) <= random_write_wakeup_bits);
-	mix_pool_bytes(poolp, buffer, count);
-	credit_entropy_bits(poolp, entropy);
-}
-EXPORT_SYMBOL_GPL(add_hwgenerator_randomness);
-
-/* Handle random seed passed by bootloader.
- * If the seed is trustworthy, it would be regarded as hardware RNGs. Otherwise
- * it would be regarded as device data.
- * The decision is controlled by CONFIG_RANDOM_TRUST_BOOTLOADER.
- */
-void add_bootloader_randomness(const void *buf, unsigned int size)
-{
-	if (IS_ENABLED(CONFIG_RANDOM_TRUST_BOOTLOADER))
-		add_hwgenerator_randomness(buf, size, size * 8);
-	else
-		add_device_randomness(buf, size);
-}
-EXPORT_SYMBOL_GPL(add_bootloader_randomness);
+#endif	/* CONFIG_SYSCTL */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/eventlog/acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/eventlog/acpi.c
@@ -14,6 +14,7 @@
  * Access to the event log extended by the TCG BIOS of PC platform
  */
 
+#include <linux/device.h>
 #include <linux/seq_file.h>
 #include <linux/fs.h>
 #include <linux/security.h>
@@ -62,6 +63,11 @@
 	return n == 0;
 }
 
+static void tpm_bios_log_free(void *data)
+{
+	kvfree(data);
+}
+
 /* read binary bios log */
 int tpm_read_log_acpi(struct tpm_chip *chip)
 {
@@ -90,16 +96,21 @@
 			return -ENODEV;
 
 		if (tbl->header.length <
-				sizeof(*tbl) + sizeof(struct acpi_tpm2_phy))
+				sizeof(*tbl) + sizeof(struct acpi_tpm2_phy)) {
+			acpi_put_table((struct acpi_table_header *)tbl);
 			return -ENODEV;
+		}
 
 		tpm2_phy = (void *)tbl + sizeof(*tbl);
 		len = tpm2_phy->log_area_minimum_length;
 
 		start = tpm2_phy->log_area_start_address;
-		if (!start || !len)
+		if (!start || !len) {
+			acpi_put_table((struct acpi_table_header *)tbl);
 			return -ENODEV;
+		}
 
+		acpi_put_table((struct acpi_table_header *)tbl);
 		format = EFI_TCG2_EVENT_LOG_FORMAT_TCG_2;
 	} else {
 		/* Find TCPA entry in RSDT (ACPI_LOGICAL_ADDRESSING) */
@@ -120,15 +131,17 @@
 			break;
 		}
 
+		acpi_put_table((struct acpi_table_header *)buff);
 		format = EFI_TCG2_EVENT_LOG_FORMAT_TCG_1_2;
 	}
+
 	if (!len) {
 		dev_warn(&chip->dev, "%s: TCPA log area empty\n", __func__);
 		return -EIO;
 	}
 
 	/* malloc EventLog space */
-	log->bios_event_log = kmalloc(len, GFP_KERNEL);
+	log->bios_event_log = kvmalloc(len, GFP_KERNEL);
 	if (!log->bios_event_log)
 		return -ENOMEM;
 
@@ -136,8 +149,12 @@
 
 	ret = -EIO;
 	virt = acpi_os_map_iomem(start, len);
-	if (!virt)
+	if (!virt) {
+		dev_warn(&chip->dev, "%s: Failed to map ACPI memory\n", __func__);
+		/* try EFI log next */
+		ret = -ENODEV;
 		goto err;
+	}
 
 	memcpy_fromio(log->bios_event_log, virt, len);
 
@@ -150,11 +167,16 @@
 		goto err;
 	}
 
+	ret = devm_add_action(&chip->dev, tpm_bios_log_free, log->bios_event_log);
+	if (ret) {
+		log->bios_event_log = NULL;
+		goto err;
+	}
+
 	return format;
 
 err:
-	kfree(log->bios_event_log);
+	tpm_bios_log_free(log->bios_event_log);
 	log->bios_event_log = NULL;
 	return ret;
-
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/eventlog/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/eventlog/common.c
@@ -47,6 +47,8 @@
 	if (!err) {
 		seq = file->private_data;
 		seq->private = chip;
+	} else {
+		put_device(&chip->dev);
 	}
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/eventlog/efi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/eventlog/efi.c
@@ -6,6 +6,7 @@
  *      Thiebaud Weksteen <tweek@google.com>
  */
 
+#include <linux/device.h>
 #include <linux/efi.h>
 #include <linux/tpm_eventlog.h>
 
@@ -55,7 +56,7 @@
 	}
 
 	/* malloc EventLog space */
-	log->bios_event_log = kmemdup(log_tbl->log, log_size, GFP_KERNEL);
+	log->bios_event_log = devm_kmemdup(&chip->dev, log_tbl->log, log_size, GFP_KERNEL);
 	if (!log->bios_event_log) {
 		ret = -ENOMEM;
 		goto out;
@@ -76,7 +77,7 @@
 			     MEMREMAP_WB);
 	if (!final_tbl) {
 		pr_err("Could not map UEFI TPM final log\n");
-		kfree(log->bios_event_log);
+		devm_kfree(&chip->dev, log->bios_event_log);
 		ret = -ENOMEM;
 		goto out;
 	}
@@ -91,11 +92,11 @@
 	 * Allocate memory for the 'combined log' where we will append the
 	 * 'final events log' to.
 	 */
-	tmp = krealloc(log->bios_event_log,
-		       log_size + final_events_log_size,
-		       GFP_KERNEL);
+	tmp = devm_krealloc(&chip->dev, log->bios_event_log,
+			    log_size + final_events_log_size,
+			    GFP_KERNEL);
 	if (!tmp) {
-		kfree(log->bios_event_log);
+		devm_kfree(&chip->dev, log->bios_event_log);
 		ret = -ENOMEM;
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/eventlog/of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/eventlog/of.c
@@ -10,6 +10,7 @@
  * Read the event log created by the firmware on PPC64
  */
 
+#include <linux/device.h>
 #include <linux/slab.h>
 #include <linux/of.h>
 #include <linux/tpm_eventlog.h>
@@ -65,7 +66,7 @@
 		return -EIO;
 	}
 
-	log->bios_event_log = kmemdup(__va(base), size, GFP_KERNEL);
+	log->bios_event_log = devm_kmemdup(&chip->dev, __va(base), size, GFP_KERNEL);
 	if (!log->bios_event_log)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm-chip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm-chip.c
@@ -267,21 +267,12 @@
 	idr_remove(&dev_nums_idr, chip->dev_num);
 	mutex_unlock(&idr_lock);
 
-	kfree(chip->log.bios_event_log);
 	kfree(chip->work_space.context_buf);
 	kfree(chip->work_space.session_buf);
 	kfree(chip->allocated_banks);
 	kfree(chip);
 }
 
-static void tpm_devs_release(struct device *dev)
-{
-	struct tpm_chip *chip = container_of(dev, struct tpm_chip, devs);
-
-	/* release the master device reference */
-	put_device(&chip->dev);
-}
-
 /**
  * tpm_class_shutdown() - prepare the TPM device for loss of power.
  * @dev: device to which the chip is associated.
@@ -344,7 +335,6 @@
 	chip->dev_num = rc;
 
 	device_initialize(&chip->dev);
-	device_initialize(&chip->devs);
 
 	chip->dev.class = tpm_class;
 	chip->dev.class->shutdown_pre = tpm_class_shutdown;
@@ -352,39 +342,20 @@
 	chip->dev.parent = pdev;
 	chip->dev.groups = chip->groups;
 
-	chip->devs.parent = pdev;
-	chip->devs.class = tpmrm_class;
-	chip->devs.release = tpm_devs_release;
-	/* get extra reference on main device to hold on
-	 * behalf of devs.  This holds the chip structure
-	 * while cdevs is in use.  The corresponding put
-	 * is in the tpm_devs_release (TPM2 only)
-	 */
-	if (chip->flags & TPM_CHIP_FLAG_TPM2)
-		get_device(&chip->dev);
-
 	if (chip->dev_num == 0)
 		chip->dev.devt = MKDEV(MISC_MAJOR, TPM_MINOR);
 	else
 		chip->dev.devt = MKDEV(MAJOR(tpm_devt), chip->dev_num);
 
-	chip->devs.devt =
-		MKDEV(MAJOR(tpm_devt), chip->dev_num + TPM_NUM_DEVICES);
-
 	rc = dev_set_name(&chip->dev, "tpm%d", chip->dev_num);
 	if (rc)
 		goto out;
-	rc = dev_set_name(&chip->devs, "tpmrm%d", chip->dev_num);
-	if (rc)
-		goto out;
 
 	if (!pdev)
 		chip->flags |= TPM_CHIP_FLAG_VIRTUAL;
 
 	cdev_init(&chip->cdev, &tpm_fops);
-	cdev_init(&chip->cdevs, &tpmrm_fops);
 	chip->cdev.owner = THIS_MODULE;
-	chip->cdevs.owner = THIS_MODULE;
 
 	rc = tpm2_init_space(&chip->work_space, TPM2_SPACE_BUFFER_SIZE);
 	if (rc) {
@@ -396,7 +367,6 @@
 	return chip;
 
 out:
-	put_device(&chip->devs);
 	put_device(&chip->dev);
 	return ERR_PTR(rc);
 }
@@ -445,14 +415,9 @@
 	}
 
 	if (chip->flags & TPM_CHIP_FLAG_TPM2) {
-		rc = cdev_device_add(&chip->cdevs, &chip->devs);
-		if (rc) {
-			dev_err(&chip->devs,
-				"unable to cdev_device_add() %s, major %d, minor %d, err=%d\n",
-				dev_name(&chip->devs), MAJOR(chip->devs.devt),
-				MINOR(chip->devs.devt), rc);
-			return rc;
-		}
+		rc = tpm_devs_add(chip);
+		if (rc)
+			goto err_del_cdev;
 	}
 
 	/* Make the chip available. */
@@ -460,6 +425,10 @@
 	idr_replace(&dev_nums_idr, chip, chip->dev_num);
 	mutex_unlock(&idr_lock);
 
+	return 0;
+
+err_del_cdev:
+	cdev_device_del(&chip->cdev, &chip->dev);
 	return rc;
 }
 
@@ -474,13 +443,21 @@
 
 	/* Make the driver uncallable. */
 	down_write(&chip->ops_sem);
-	if (chip->flags & TPM_CHIP_FLAG_TPM2) {
-		if (!tpm_chip_start(chip)) {
-			tpm2_shutdown(chip, TPM2_SU_CLEAR);
-			tpm_chip_stop(chip);
+
+	/*
+	 * Check if chip->ops is still valid: In case that the controller
+	 * drivers shutdown handler unregisters the controller in its
+	 * shutdown handler we are called twice and chip->ops to NULL.
+	 */
+	if (chip->ops) {
+		if (chip->flags & TPM_CHIP_FLAG_TPM2) {
+			if (!tpm_chip_start(chip)) {
+				tpm2_shutdown(chip, TPM2_SU_CLEAR);
+				tpm_chip_stop(chip);
+			}
 		}
+		chip->ops = NULL;
 	}
-	chip->ops = NULL;
 	up_write(&chip->ops_sem);
 }
 
@@ -641,7 +618,7 @@
 		hwrng_unregister(&chip->hwrng);
 	tpm_bios_log_teardown(chip);
 	if (chip->flags & TPM_CHIP_FLAG_TPM2)
-		cdev_device_del(&chip->cdevs, &chip->devs);
+		tpm_devs_remove(chip);
 	tpm_del_char_device(chip);
 }
 EXPORT_SYMBOL_GPL(tpm_chip_unregister);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm-dev-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm-dev-common.c
@@ -47,6 +47,8 @@
 
 	if (!ret)
 		ret = tpm2_commit_space(chip, space, buf, &len);
+	else
+		tpm2_flush_space(chip);
 
 out_rc:
 	return ret ? ret : len;
@@ -69,7 +71,13 @@
 	ret = tpm_dev_transmit(priv->chip, priv->space, priv->data_buffer,
 			       sizeof(priv->data_buffer));
 	tpm_put_ops(priv->chip);
-	if (ret > 0) {
+
+	/*
+	 * If ret is > 0 then tpm_dev_transmit returned the size of the
+	 * response. If ret is < 0 then tpm_dev_transmit failed and
+	 * returned an error code.
+	 */
+	if (ret != 0) {
 		priv->response_length = ret;
 		mod_timer(&priv->user_read_timer, jiffies + (120 * HZ));
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm-interface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm-interface.c
@@ -401,13 +401,14 @@
 	    !pm_suspend_via_firmware())
 		goto suspended;
 
-	if (!tpm_chip_start(chip)) {
+	rc = tpm_try_get_ops(chip);
+	if (!rc) {
 		if (chip->flags & TPM_CHIP_FLAG_TPM2)
 			tpm2_shutdown(chip, TPM2_SU_STATE);
 		else
 			rc = tpm1_pm_suspend(chip, tpm_suspend_pcr);
 
-		tpm_chip_stop(chip);
+		tpm_put_ops(chip);
 	}
 
 suspended:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm.h
@@ -234,6 +234,8 @@
 		       size_t cmdsiz);
 int tpm2_commit_space(struct tpm_chip *chip, struct tpm_space *space, void *buf,
 		      size_t *bufsiz);
+int tpm_devs_add(struct tpm_chip *chip);
+void tpm_devs_remove(struct tpm_chip *chip);
 
 void tpm_bios_log_setup(struct tpm_chip *chip);
 void tpm_bios_log_teardown(struct tpm_chip *chip);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm2-cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm2-cmd.c
@@ -400,7 +400,16 @@
 	if (!rc) {
 		out = (struct tpm2_get_cap_out *)
 			&buf.data[TPM_HEADER_SIZE];
-		*value = be32_to_cpu(out->value);
+		/*
+		 * To prevent failing boot up of some systems, Infineon TPM2.0
+		 * returns SUCCESS on TPM2_Startup in field upgrade mode. Also
+		 * the TPM2_Getcapability command returns a zero length list
+		 * in field upgrade mode.
+		 */
+		if (be32_to_cpu(out->property_cnt) > 0)
+			*value = be32_to_cpu(out->value);
+		else
+			rc = -ENODATA;
 	}
 	tpm_buf_destroy(&buf);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm2-space.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm2-space.c
@@ -58,12 +58,12 @@
 
 void tpm2_del_space(struct tpm_chip *chip, struct tpm_space *space)
 {
-	mutex_lock(&chip->tpm_mutex);
-	if (!tpm_chip_start(chip)) {
+
+	if (tpm_try_get_ops(chip) == 0) {
 		tpm2_flush_sessions(chip, space);
-		tpm_chip_stop(chip);
+		tpm_put_ops(chip);
 	}
-	mutex_unlock(&chip->tpm_mutex);
+
 	kfree(space->context_buf);
 	kfree(space->session_buf);
 }
@@ -166,6 +166,9 @@
 	struct tpm_space *space = &chip->work_space;
 	int i;
 
+	if (!space)
+		return;
+
 	for (i = 0; i < ARRAY_SIZE(space->context_tbl); i++)
 		if (space->context_tbl[i] && ~space->context_tbl[i])
 			tpm2_flush_context(chip, space->context_tbl[i]);
@@ -455,6 +458,9 @@
 	if (be32_to_cpu(data->capability) != TPM2_CAP_HANDLES)
 		return 0;
 
+	if (be32_to_cpu(data->count) > (UINT_MAX - TPM_HEADER_SIZE - 9) / 4)
+		return -EFAULT;
+
 	if (len != TPM_HEADER_SIZE + 9 + 4 * be32_to_cpu(data->count))
 		return -EFAULT;
 
@@ -571,3 +577,68 @@
 	dev_err(&chip->dev, "%s: error %d\n", __func__, rc);
 	return rc;
 }
+
+/*
+ * Put the reference to the main device.
+ */
+static void tpm_devs_release(struct device *dev)
+{
+	struct tpm_chip *chip = container_of(dev, struct tpm_chip, devs);
+
+	/* release the master device reference */
+	put_device(&chip->dev);
+}
+
+/*
+ * Remove the device file for exposed TPM spaces and release the device
+ * reference. This may also release the reference to the master device.
+ */
+void tpm_devs_remove(struct tpm_chip *chip)
+{
+	cdev_device_del(&chip->cdevs, &chip->devs);
+	put_device(&chip->devs);
+}
+
+/*
+ * Add a device file to expose TPM spaces. Also take a reference to the
+ * main device.
+ */
+int tpm_devs_add(struct tpm_chip *chip)
+{
+	int rc;
+
+	device_initialize(&chip->devs);
+	chip->devs.parent = chip->dev.parent;
+	chip->devs.class = tpmrm_class;
+
+	/*
+	 * Get extra reference on main device to hold on behalf of devs.
+	 * This holds the chip structure while cdevs is in use. The
+	 * corresponding put is in the tpm_devs_release.
+	 */
+	get_device(&chip->dev);
+	chip->devs.release = tpm_devs_release;
+	chip->devs.devt = MKDEV(MAJOR(tpm_devt), chip->dev_num + TPM_NUM_DEVICES);
+	cdev_init(&chip->cdevs, &tpmrm_fops);
+	chip->cdevs.owner = THIS_MODULE;
+
+	rc = dev_set_name(&chip->devs, "tpmrm%d", chip->dev_num);
+	if (rc)
+		goto err_put_devs;
+
+	rc = cdev_device_add(&chip->cdevs, &chip->devs);
+	if (rc) {
+		dev_err(&chip->devs,
+			"unable to cdev_device_add() %s, major %d, minor %d, err=%d\n",
+			dev_name(&chip->devs), MAJOR(chip->devs.devt),
+			MINOR(chip->devs.devt), rc);
+		goto err_put_devs;
+	}
+
+	return 0;
+
+err_put_devs:
+	put_device(&chip->devs);
+
+	return rc;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_crb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_crb.c
@@ -252,7 +252,7 @@
 	iowrite32(CRB_LOC_CTRL_RELINQUISH, &priv->regs_h->loc_ctrl);
 	if (!crb_wait_for_reg_32(&priv->regs_h->loc_state, mask, value,
 				 TPM2_TIMEOUT_C)) {
-		dev_warn(dev, "TPM_LOC_STATE_x.requestAccess timed out\n");
+		dev_warn(dev, "TPM_LOC_STATE_x.Relinquish timed out\n");
 		return -ETIME;
 	}
 
@@ -676,12 +676,16 @@
 
 	/* Should the FIFO driver handle this? */
 	sm = buf->start_method;
-	if (sm == ACPI_TPM2_MEMORY_MAPPED)
-		return -ENODEV;
+	if (sm == ACPI_TPM2_MEMORY_MAPPED) {
+		rc = -ENODEV;
+		goto out;
+	}
 
 	priv = devm_kzalloc(dev, sizeof(struct crb_priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
+	if (!priv) {
+		rc = -ENOMEM;
+		goto out;
+	}
 
 	if (sm == ACPI_TPM2_COMMAND_BUFFER_WITH_ARM_SMC) {
 		if (buf->header.length < (sizeof(*buf) + sizeof(*crb_smc))) {
@@ -689,7 +693,8 @@
 				FW_BUG "TPM2 ACPI table has wrong size %u for start method type %d\n",
 				buf->header.length,
 				ACPI_TPM2_COMMAND_BUFFER_WITH_ARM_SMC);
-			return -EINVAL;
+			rc = -EINVAL;
+			goto out;
 		}
 		crb_smc = ACPI_ADD_PTR(struct tpm2_crb_smc, buf, sizeof(*buf));
 		priv->smc_func_id = crb_smc->smc_func_id;
@@ -700,17 +705,23 @@
 
 	rc = crb_map_io(device, priv, buf);
 	if (rc)
-		return rc;
+		goto out;
 
 	chip = tpmm_chip_alloc(dev, &tpm_crb);
-	if (IS_ERR(chip))
-		return PTR_ERR(chip);
+	if (IS_ERR(chip)) {
+		rc = PTR_ERR(chip);
+		goto out;
+	}
 
 	dev_set_drvdata(&chip->dev, priv);
 	chip->acpi_dev_handle = device->handle;
 	chip->flags = TPM_CHIP_FLAG_TPM2;
 
-	return tpm_chip_register(chip);
+	rc = tpm_chip_register(chip);
+
+out:
+	acpi_put_table((struct acpi_table_header *)buf);
+	return rc;
 }
 
 static int crb_acpi_remove(struct acpi_device *device)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_ftpm_tee.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_ftpm_tee.c
@@ -397,7 +397,13 @@
 	if (rc)
 		return rc;
 
-	return driver_register(&ftpm_tee_driver.driver);
+	rc = driver_register(&ftpm_tee_driver.driver);
+	if (rc) {
+		platform_driver_unregister(&ftpm_tee_plat_driver);
+		return rc;
+	}
+
+	return 0;
 }
 
 static void __exit ftpm_mod_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_ibmvtpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_ibmvtpm.c
@@ -681,6 +681,7 @@
 	if (!wait_event_timeout(ibmvtpm->crq_queue.wq,
 				ibmvtpm->rtce_buf != NULL,
 				HZ)) {
+		rc = -ENODEV;
 		dev_err(dev, "CRQ response timed out\n");
 		goto init_irq_cleanup;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_tis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_tis.c
@@ -83,6 +83,22 @@
 			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad T490s"),
 		},
 	},
+	{
+		.callback = tpm_tis_disable_irq,
+		.ident = "ThinkStation P360 Tiny",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkStation P360 Tiny"),
+		},
+	},
+	{
+		.callback = tpm_tis_disable_irq,
+		.ident = "ThinkPad L490",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad L490"),
+		},
+	},
 	{}
 };
 
@@ -125,6 +141,7 @@
 	const struct acpi_device_id *aid = acpi_match_device(tpm_acpi_tbl, dev);
 	struct acpi_table_tpm2 *tbl;
 	acpi_status st;
+	int ret = 0;
 
 	if (!aid || aid->driver_data != DEVICE_IS_TPM2)
 		return 0;
@@ -132,8 +149,7 @@
 	/* If the ACPI TPM2 signature is matched then a global ACPI_SIG_TPM2
 	 * table is mandatory
 	 */
-	st =
-	    acpi_get_table(ACPI_SIG_TPM2, 1, (struct acpi_table_header **)&tbl);
+	st = acpi_get_table(ACPI_SIG_TPM2, 1, (struct acpi_table_header **)&tbl);
 	if (ACPI_FAILURE(st) || tbl->header.length < sizeof(*tbl)) {
 		dev_err(dev, FW_BUG "failed to get TPM2 ACPI table\n");
 		return -EINVAL;
@@ -141,9 +157,10 @@
 
 	/* The tpm2_crb driver handles this device */
 	if (tbl->start_method != ACPI_TPM2_MEMORY_MAPPED)
-		return -ENODEV;
+		ret = -ENODEV;
 
-	return 0;
+	acpi_put_table((struct acpi_table_header *)tbl);
+	return ret;
 }
 #else
 static int check_acpi_tpm2(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_tis_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_tis_core.c
@@ -48,6 +48,7 @@
 		unsigned long timeout, wait_queue_head_t *queue,
 		bool check_cancel)
 {
+	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
 	unsigned long stop;
 	long rc;
 	u8 status;
@@ -80,8 +81,8 @@
 		}
 	} else {
 		do {
-			usleep_range(TPM_TIMEOUT_USECS_MIN,
-				     TPM_TIMEOUT_USECS_MAX);
+			usleep_range(priv->timeout_min,
+				     priv->timeout_max);
 			status = chip->ops->status(chip);
 			if ((status & mask) == mask)
 				return 0;
@@ -135,16 +136,27 @@
 	return false;
 }
 
-static int release_locality(struct tpm_chip *chip, int l)
+static int __tpm_tis_relinquish_locality(struct tpm_tis_data *priv, int l)
+{
+	tpm_tis_write8(priv, TPM_ACCESS(l), TPM_ACCESS_ACTIVE_LOCALITY);
+
+	return 0;
+}
+
+static int tpm_tis_relinquish_locality(struct tpm_chip *chip, int l)
 {
 	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
 
-	tpm_tis_write8(priv, TPM_ACCESS(l), TPM_ACCESS_ACTIVE_LOCALITY);
+	mutex_lock(&priv->locality_count_mutex);
+	priv->locality_count--;
+	if (priv->locality_count == 0)
+		__tpm_tis_relinquish_locality(priv, l);
+	mutex_unlock(&priv->locality_count_mutex);
 
 	return 0;
 }
 
-static int request_locality(struct tpm_chip *chip, int l)
+static int __tpm_tis_request_locality(struct tpm_chip *chip, int l)
 {
 	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
 	unsigned long stop, timeout;
@@ -185,6 +197,20 @@
 	return -1;
 }
 
+static int tpm_tis_request_locality(struct tpm_chip *chip, int l)
+{
+	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
+	int ret = 0;
+
+	mutex_lock(&priv->locality_count_mutex);
+	if (priv->locality_count == 0)
+		ret = __tpm_tis_request_locality(chip, l);
+	if (!ret)
+		priv->locality_count++;
+	mutex_unlock(&priv->locality_count_mutex);
+	return ret;
+}
+
 static u8 tpm_tis_status(struct tpm_chip *chip)
 {
 	struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
@@ -288,6 +314,7 @@
 	int size = 0;
 	int status;
 	u32 expected;
+	int rc;
 
 	if (count < TPM_HEADER_SIZE) {
 		size = -EIO;
@@ -307,8 +334,13 @@
 		goto out;
 	}
 
-	size += recv_data(chip, &buf[TPM_HEADER_SIZE],
-			  expected - TPM_HEADER_SIZE);
+	rc = recv_data(chip, &buf[TPM_HEADER_SIZE],
+		       expected - TPM_HEADER_SIZE);
+	if (rc < 0) {
+		size = rc;
+		goto out;
+	}
+	size += rc;
 	if (size < expected) {
 		dev_err(&chip->dev, "Unable to read remainder of result\n");
 		size = -ETIME;
@@ -437,10 +469,17 @@
 	int rc;
 	u32 ordinal;
 	unsigned long dur;
+	unsigned int try;
 
-	rc = tpm_tis_send_data(chip, buf, len);
-	if (rc < 0)
-		return rc;
+	for (try = 0; try < TPM_RETRY; try++) {
+		rc = tpm_tis_send_data(chip, buf, len);
+		if (rc >= 0)
+			/* Data transfer done successfully */
+			break;
+		else if (rc != -EIO)
+			/* Data transfer failed, not recoverable */
+			return rc;
+	}
 
 	/* go and do it */
 	rc = tpm_tis_write8(priv, TPM_STS(priv->locality), TPM_STS_GO);
@@ -637,7 +676,7 @@
 	if (vendor != TPM_VID_INTEL)
 		return 0;
 
-	if (request_locality(chip, 0) != 0)
+	if (tpm_tis_request_locality(chip, 0) != 0)
 		return -EBUSY;
 
 	rc = tpm_tis_send_data(chip, cmd_getticks, len);
@@ -658,7 +697,7 @@
 
 out:
 	tpm_tis_ready(chip);
-	release_locality(chip, priv->locality);
+	tpm_tis_relinquish_locality(chip, priv->locality);
 
 	return rc;
 }
@@ -705,7 +744,9 @@
 		wake_up_interruptible(&priv->int_queue);
 
 	/* Clear interrupts handled with TPM_EOI */
+	tpm_tis_request_locality(chip, 0);
 	rc = tpm_tis_write32(priv, TPM_INT_STATUS(priv->locality), interrupt);
+	tpm_tis_relinquish_locality(chip, 0);
 	if (rc < 0)
 		return IRQ_NONE;
 
@@ -713,25 +754,17 @@
 	return IRQ_HANDLED;
 }
 
-static int tpm_tis_gen_interrupt(struct tpm_chip *chip)
+static void tpm_tis_gen_interrupt(struct tpm_chip *chip)
 {
 	const char *desc = "attempting to generate an interrupt";
 	u32 cap2;
 	cap_t cap;
 	int ret;
 
-	ret = request_locality(chip, 0);
-	if (ret < 0)
-		return ret;
-
 	if (chip->flags & TPM_CHIP_FLAG_TPM2)
 		ret = tpm2_get_tpm_pt(chip, 0x100, &cap2, desc);
 	else
 		ret = tpm1_getcap(chip, TPM_CAP_PROP_TIS_TIMEOUT, &cap, desc, 0);
-
-	release_locality(chip, 0);
-
-	return ret;
 }
 
 /* Register the IRQ and issue a command that will cause an interrupt. If an
@@ -746,60 +779,66 @@
 	int rc;
 	u32 int_status;
 
-	if (devm_request_irq(chip->dev.parent, irq, tis_int_handler, flags,
-			     dev_name(&chip->dev), chip) != 0) {
+
+	rc = devm_request_threaded_irq(chip->dev.parent, irq, NULL,
+				       tis_int_handler, IRQF_ONESHOT | flags,
+				       dev_name(&chip->dev), chip);
+	if (rc) {
 		dev_info(&chip->dev, "Unable to request irq: %d for probe\n",
 			 irq);
 		return -1;
 	}
 	priv->irq = irq;
 
+	rc = tpm_tis_request_locality(chip, 0);
+	if (rc < 0)
+		return rc;
+
 	rc = tpm_tis_read8(priv, TPM_INT_VECTOR(priv->locality),
 			   &original_int_vec);
-	if (rc < 0)
+	if (rc < 0) {
+		tpm_tis_relinquish_locality(chip, priv->locality);
 		return rc;
+	}
 
 	rc = tpm_tis_write8(priv, TPM_INT_VECTOR(priv->locality), irq);
 	if (rc < 0)
-		return rc;
+		goto restore_irqs;
 
 	rc = tpm_tis_read32(priv, TPM_INT_STATUS(priv->locality), &int_status);
 	if (rc < 0)
-		return rc;
+		goto restore_irqs;
 
 	/* Clear all existing */
 	rc = tpm_tis_write32(priv, TPM_INT_STATUS(priv->locality), int_status);
 	if (rc < 0)
-		return rc;
-
+		goto restore_irqs;
 	/* Turn on */
 	rc = tpm_tis_write32(priv, TPM_INT_ENABLE(priv->locality),
 			     intmask | TPM_GLOBAL_INT_ENABLE);
 	if (rc < 0)
-		return rc;
+		goto restore_irqs;
 
 	priv->irq_tested = false;
 
 	/* Generate an interrupt by having the core call through to
 	 * tpm_tis_send
 	 */
-	rc = tpm_tis_gen_interrupt(chip);
-	if (rc < 0)
-		return rc;
+	tpm_tis_gen_interrupt(chip);
 
+restore_irqs:
 	/* tpm_tis_send will either confirm the interrupt is working or it
 	 * will call disable_irq which undoes all of the above.
 	 */
 	if (!(chip->flags & TPM_CHIP_FLAG_IRQ)) {
-		rc = tpm_tis_write8(priv, original_int_vec,
-				TPM_INT_VECTOR(priv->locality));
-		if (rc < 0)
-			return rc;
-
-		return 1;
+		tpm_tis_write8(priv, original_int_vec,
+			       TPM_INT_VECTOR(priv->locality));
+		rc = -1;
 	}
 
-	return 0;
+	tpm_tis_relinquish_locality(chip, priv->locality);
+
+	return rc;
 }
 
 /* Try to find the IRQ the TPM is using. This is for legacy x86 systems that
@@ -913,8 +952,8 @@
 	.req_complete_mask = TPM_STS_DATA_AVAIL | TPM_STS_VALID,
 	.req_complete_val = TPM_STS_DATA_AVAIL | TPM_STS_VALID,
 	.req_canceled = tpm_tis_req_canceled,
-	.request_locality = request_locality,
-	.relinquish_locality = release_locality,
+	.request_locality = tpm_tis_request_locality,
+	.relinquish_locality = tpm_tis_relinquish_locality,
 	.clk_enable = tpm_tis_clkrun_enable,
 };
 
@@ -945,9 +984,26 @@
 	chip->timeout_b = msecs_to_jiffies(TIS_TIMEOUT_B_MAX);
 	chip->timeout_c = msecs_to_jiffies(TIS_TIMEOUT_C_MAX);
 	chip->timeout_d = msecs_to_jiffies(TIS_TIMEOUT_D_MAX);
+	priv->timeout_min = TPM_TIMEOUT_USECS_MIN;
+	priv->timeout_max = TPM_TIMEOUT_USECS_MAX;
 	priv->phy_ops = phy_ops;
+	priv->locality_count = 0;
+	mutex_init(&priv->locality_count_mutex);
+
 	dev_set_drvdata(&chip->dev, priv);
 
+	rc = tpm_tis_read32(priv, TPM_DID_VID(0), &vendor);
+	if (rc < 0)
+		return rc;
+
+	priv->manufacturer_id = vendor;
+
+	if (priv->manufacturer_id == TPM_VID_ATML &&
+		!(chip->flags & TPM_CHIP_FLAG_TPM2)) {
+		priv->timeout_min = TIS_TIMEOUT_MIN_ATML;
+		priv->timeout_max = TIS_TIMEOUT_MAX_ATML;
+	}
+
 	if (is_bsw()) {
 		priv->ilb_base_addr = ioremap(INTEL_LEGACY_BLK_BASE_ADDR,
 					ILB_REMAP_SIZE);
@@ -978,7 +1034,15 @@
 	intmask |= TPM_INTF_CMD_READY_INT | TPM_INTF_LOCALITY_CHANGE_INT |
 		   TPM_INTF_DATA_AVAIL_INT | TPM_INTF_STS_VALID_INT;
 	intmask &= ~TPM_GLOBAL_INT_ENABLE;
+
+	rc = tpm_tis_request_locality(chip, 0);
+	if (rc < 0) {
+		rc = -ENODEV;
+		goto out_err;
+	}
+
 	tpm_tis_write32(priv, TPM_INT_ENABLE(priv->locality), intmask);
+	tpm_tis_relinquish_locality(chip, 0);
 
 	rc = tpm_chip_start(chip);
 	if (rc)
@@ -988,12 +1052,6 @@
 	if (rc)
 		goto out_err;
 
-	rc = tpm_tis_read32(priv, TPM_DID_VID(0), &vendor);
-	if (rc < 0)
-		goto out_err;
-
-	priv->manufacturer_id = vendor;
-
 	rc = tpm_tis_read8(priv, TPM_RID(0), &rid);
 	if (rc < 0)
 		goto out_err;
@@ -1044,13 +1102,13 @@
 		 * proper timeouts for the driver.
 		 */
 
-		rc = request_locality(chip, 0);
+		rc = tpm_tis_request_locality(chip, 0);
 		if (rc < 0)
 			goto out_err;
 
 		rc = tpm_get_timeouts(chip);
 
-		release_locality(chip, 0);
+		tpm_tis_relinquish_locality(chip, 0);
 
 		if (rc) {
 			dev_err(dev, "Could not get TPM timeouts and durations\n");
@@ -1058,17 +1116,21 @@
 			goto out_err;
 		}
 
-		if (irq) {
+		if (irq)
 			tpm_tis_probe_irq_single(chip, intmask, IRQF_SHARED,
 						 irq);
-			if (!(chip->flags & TPM_CHIP_FLAG_IRQ)) {
-				dev_err(&chip->dev, FW_BUG
+		else
+			tpm_tis_probe_irq(chip, intmask);
+
+		if (!(chip->flags & TPM_CHIP_FLAG_IRQ)) {
+			dev_err(&chip->dev, FW_BUG
 					"TPM interrupt not working, polling instead\n");
 
-				disable_interrupts(chip);
-			}
-		} else {
-			tpm_tis_probe_irq(chip, intmask);
+			rc = tpm_tis_request_locality(chip, 0);
+			if (rc < 0)
+				goto out_err;
+			disable_interrupts(chip);
+			tpm_tis_relinquish_locality(chip, 0);
 		}
 	}
 
@@ -1129,28 +1191,27 @@
 	struct tpm_chip *chip = dev_get_drvdata(dev);
 	int ret;
 
+	ret = tpm_tis_request_locality(chip, 0);
+	if (ret < 0)
+		return ret;
+
 	if (chip->flags & TPM_CHIP_FLAG_IRQ)
 		tpm_tis_reenable_interrupts(chip);
 
 	ret = tpm_pm_resume(dev);
 	if (ret)
-		return ret;
+		goto out;
 
 	/*
 	 * TPM 1.2 requires self-test on resume. This function actually returns
 	 * an error code but for unknown reason it isn't handled.
 	 */
-	if (!(chip->flags & TPM_CHIP_FLAG_TPM2)) {
-		ret = request_locality(chip, 0);
-		if (ret < 0)
-			return ret;
-
+	if (!(chip->flags & TPM_CHIP_FLAG_TPM2))
 		tpm1_do_selftest(chip);
+out:
+	tpm_tis_relinquish_locality(chip, 0);
 
-		release_locality(chip, 0);
-	}
-
-	return 0;
+	return ret;
 }
 EXPORT_SYMBOL_GPL(tpm_tis_resume);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_tis_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_tis_core.h
@@ -54,6 +54,8 @@
 	TIS_MEM_LEN = 0x5000,
 	TIS_SHORT_TIMEOUT = 750,	/* ms */
 	TIS_LONG_TIMEOUT = 2000,	/* 2 sec */
+	TIS_TIMEOUT_MIN_ATML = 14700,	/* usecs */
+	TIS_TIMEOUT_MAX_ATML = 15000,	/* usecs */
 };
 
 /* Some timeout values are needed before it is known whether the chip is
@@ -88,6 +90,8 @@
 
 struct tpm_tis_data {
 	u16 manufacturer_id;
+	struct mutex locality_count_mutex;
+	unsigned int locality_count;
 	int locality;
 	int irq;
 	bool irq_tested;
@@ -98,6 +102,8 @@
 	wait_queue_head_t read_queue;
 	const struct tpm_tis_phy_ops *phy_ops;
 	unsigned short rng_quality;
+	unsigned int timeout_min; /* usecs */
+	unsigned int timeout_max; /* usecs */
 };
 
 struct tpm_tis_phy_ops {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_tis_i2c_cr50.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_tis_i2c_cr50.c
@@ -754,8 +754,8 @@
 	struct device *dev = &client->dev;
 
 	if (!chip) {
-		dev_err(dev, "Could not get client data at remove\n");
-		return -ENODEV;
+		dev_crit(dev, "Could not get client data at remove, memory corruption ahead\n");
+		return 0;
 	}
 
 	tpm_chip_unregister(chip);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_tis_spi_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_tis_spi_main.c
@@ -267,6 +267,7 @@
 	{ "st33htpm-spi", (unsigned long)tpm_tis_spi_probe },
 	{ "slb9670", (unsigned long)tpm_tis_spi_probe },
 	{ "tpm_tis_spi", (unsigned long)tpm_tis_spi_probe },
+	{ "tpm_tis-spi", (unsigned long)tpm_tis_spi_probe },
 	{ "cr50", (unsigned long)cr50_spi_probe },
 	{}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/tpm/tpm_vtpm_proxy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/tpm/tpm_vtpm_proxy.c
@@ -683,37 +683,21 @@
 	.fops = &vtpmx_fops,
 };
 
-static int vtpmx_init(void)
-{
-	return misc_register(&vtpmx_miscdev);
-}
-
-static void vtpmx_cleanup(void)
-{
-	misc_deregister(&vtpmx_miscdev);
-}
-
 static int __init vtpm_module_init(void)
 {
 	int rc;
 
-	rc = vtpmx_init();
-	if (rc) {
-		pr_err("couldn't create vtpmx device\n");
-		return rc;
-	}
-
 	workqueue = create_workqueue("tpm-vtpm");
 	if (!workqueue) {
 		pr_err("couldn't create workqueue\n");
-		rc = -ENOMEM;
-		goto err_vtpmx_cleanup;
+		return -ENOMEM;
 	}
 
-	return 0;
-
-err_vtpmx_cleanup:
-	vtpmx_cleanup();
+	rc = misc_register(&vtpmx_miscdev);
+	if (rc) {
+		pr_err("couldn't create vtpmx device\n");
+		destroy_workqueue(workqueue);
+	}
 
 	return rc;
 }
@@ -721,7 +705,7 @@
 static void __exit vtpm_module_exit(void)
 {
 	destroy_workqueue(workqueue);
-	vtpmx_cleanup();
+	misc_deregister(&vtpmx_miscdev);
 }
 
 module_init(vtpm_module_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/virtio_console.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/virtio_console.c
@@ -1956,6 +1956,13 @@
 	list_del(&portdev->list);
 	spin_unlock_irq(&pdrvdata_lock);
 
+	/* Device is going away, exit any polling for buffers */
+	virtio_break_device(vdev);
+	if (use_multiport(portdev))
+		flush_work(&portdev->control_work);
+	else
+		flush_work(&portdev->config_work);
+
 	/* Disable interrupts for vqs */
 	vdev->config->reset(vdev);
 	/* Finish up work that's lined up */
@@ -2039,25 +2046,27 @@
 		multiport = true;
 	}
 
-	err = init_vqs(portdev);
-	if (err < 0) {
-		dev_err(&vdev->dev, "Error %d initializing vqs\n", err);
-		goto free_chrdev;
-	}
-
 	spin_lock_init(&portdev->ports_lock);
 	INIT_LIST_HEAD(&portdev->ports);
 	INIT_LIST_HEAD(&portdev->list);
 
-	virtio_device_ready(portdev->vdev);
-
 	INIT_WORK(&portdev->config_work, &config_work_handler);
 	INIT_WORK(&portdev->control_work, &control_work_handler);
 
 	if (multiport) {
 		spin_lock_init(&portdev->c_ivq_lock);
 		spin_lock_init(&portdev->c_ovq_lock);
+	}
+
+	err = init_vqs(portdev);
+	if (err < 0) {
+		dev_err(&vdev->dev, "Error %d initializing vqs\n", err);
+		goto free_chrdev;
+	}
 
+	virtio_device_ready(portdev->vdev);
+
+	if (multiport) {
 		err = fill_queue(portdev->c_ivq, &portdev->c_ivq_lock);
 		if (err < 0) {
 			dev_err(&vdev->dev,
@@ -2229,7 +2238,7 @@
 	.remove =	virtcons_remove,
 };
 
-static int __init init(void)
+static int __init virtio_console_init(void)
 {
 	int err;
 
@@ -2264,7 +2273,7 @@
 	return err;
 }
 
-static void __exit fini(void)
+static void __exit virtio_console_fini(void)
 {
 	reclaim_dma_bufs();
 
@@ -2274,8 +2283,8 @@
 	class_destroy(pdrvdata.class);
 	debugfs_remove_recursive(pdrvdata.debugfs_dir);
 }
-module_init(init);
-module_exit(fini);
+module_init(virtio_console_init);
+module_exit(virtio_console_fini);
 
 MODULE_DESCRIPTION("Virtio console driver");
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/char/xillybus/xillyusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/char/xillybus/xillyusb.c
@@ -50,6 +50,7 @@
 static const char xillyname[] = "xillyusb";
 
 static unsigned int fifo_buf_order;
+static struct workqueue_struct *wakeup_wq;
 
 #define USB_VENDOR_ID_XILINX		0x03fd
 #define USB_VENDOR_ID_ALTERA		0x09fb
@@ -549,6 +550,7 @@
 	if (xdev->workq)
 		destroy_workqueue(xdev->workq);
 
+	usb_put_dev(xdev->udev);
 	kfree(xdev->channels); /* Argument may be NULL, and that's fine */
 	kfree(xdev);
 }
@@ -560,10 +562,6 @@
  * errors if executed. The mechanism relies on that xdev->error is assigned
  * a non-zero value by report_io_error() prior to queueing wakeup_all(),
  * which prevents bulk_in_work() from calling process_bulk_in().
- *
- * The fact that wakeup_all() and bulk_in_work() are queued on the same
- * workqueue makes their concurrent execution very unlikely, however the
- * kernel's API doesn't seem to ensure this strictly.
  */
 
 static void wakeup_all(struct work_struct *work)
@@ -618,7 +616,7 @@
 
 	if (do_once) {
 		kref_get(&xdev->kref); /* xdev is used by work item */
-		queue_work(xdev->workq, &xdev->wakeup_workitem);
+		queue_work(wakeup_wq, &xdev->wakeup_workitem);
 	}
 }
 
@@ -1891,6 +1889,13 @@
 
 static int xillyusb_setup_base_eps(struct xillyusb_dev *xdev)
 {
+	struct usb_device *udev = xdev->udev;
+
+	/* Verify that device has the two fundamental bulk in/out endpoints */
+	if (usb_pipe_type_check(udev, usb_sndbulkpipe(udev, MSG_EP_NUM)) ||
+	    usb_pipe_type_check(udev, usb_rcvbulkpipe(udev, IN_EP_NUM)))
+		return -ENODEV;
+
 	xdev->msg_ep = endpoint_alloc(xdev, MSG_EP_NUM | USB_DIR_OUT,
 				      bulk_out_work, 1, 2);
 	if (!xdev->msg_ep)
@@ -1912,6 +1917,7 @@
 
 dealloc:
 	endpoint_dealloc(xdev->msg_ep); /* Also frees FIFO mem if allocated */
+	xdev->msg_ep = NULL;
 	return -ENOMEM;
 }
 
@@ -1919,14 +1925,15 @@
 			  __le16 *chandesc,
 			  int num_channels)
 {
-	struct xillyusb_channel *chan;
+	struct usb_device *udev = xdev->udev;
+	struct xillyusb_channel *chan, *new_channels;
 	int i;
 
 	chan = kcalloc(num_channels, sizeof(*chan), GFP_KERNEL);
 	if (!chan)
 		return -ENOMEM;
 
-	xdev->channels = chan;
+	new_channels = chan;
 
 	for (i = 0; i < num_channels; i++, chan++) {
 		unsigned int in_desc = le16_to_cpu(*chandesc++);
@@ -1955,6 +1962,15 @@
 		 */
 
 		if ((out_desc & 0x80) && i < 14) { /* Entry is valid */
+			if (usb_pipe_type_check(udev,
+						usb_sndbulkpipe(udev, i + 2))) {
+				dev_err(xdev->dev,
+					"Missing BULK OUT endpoint %d\n",
+					i + 2);
+				kfree(new_channels);
+				return -ENODEV;
+			}
+
 			chan->writable = 1;
 			chan->out_synchronous = !!(out_desc & 0x40);
 			chan->out_seekable = !!(out_desc & 0x20);
@@ -1964,6 +1980,7 @@
 		}
 	}
 
+	xdev->channels = new_channels;
 	return 0;
 }
 
@@ -2080,9 +2097,11 @@
 	 * just after responding with the IDT, there is no reason for any
 	 * work item to be running now. To be sure that xdev->channels
 	 * is updated on anything that might run in parallel, flush the
-	 * workqueue, which rarely does anything.
+	 * device's workqueue and the wakeup work item. This rarely
+	 * does anything.
 	 */
 	flush_workqueue(xdev->workq);
+	flush_work(&xdev->wakeup_workitem);
 
 	xdev->num_channels = num_channels;
 
@@ -2240,6 +2259,10 @@
 {
 	int rc = 0;
 
+	wakeup_wq = alloc_workqueue(xillyname, 0, 0);
+	if (!wakeup_wq)
+		return -ENOMEM;
+
 	if (LOG2_INITIAL_FIFO_BUF_SIZE > PAGE_SHIFT)
 		fifo_buf_order = LOG2_INITIAL_FIFO_BUF_SIZE - PAGE_SHIFT;
 	else
@@ -2247,12 +2270,17 @@
 
 	rc = usb_register(&xillyusb_driver);
 
+	if (rc)
+		destroy_workqueue(wakeup_wq);
+
 	return rc;
 }
 
 static void __exit xillyusb_exit(void)
 {
 	usb_deregister(&xillyusb_driver);
+
+	destroy_workqueue(wakeup_wq);
 }
 
 module_init(xillyusb_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/Kconfig
@@ -83,7 +83,7 @@
 config COMMON_CLK_HI655X
 	tristate "Clock driver for Hi655x" if EXPERT
 	depends on (MFD_HI655X_PMIC || COMPILE_TEST)
-	depends on REGMAP
+	select REGMAP
 	default MFD_HI655X_PMIC
 	help
 	  This driver supports the hi655x PMIC clock. This
@@ -162,6 +162,38 @@
 	help
 	  This driver supports the clocks on Bitmain BM1880 SoC.
 
+config COMMON_CLK_SI5324
+	tristate "Clock driver for SiLabs 5324 and compatible devices"
+	depends on I2C
+	depends on OF
+	select REGMAP_I2C
+	help
+	  This driver supports Silicon Labs 5324/5319/5328 programmable
+	  clock generators. Dynamic programming of the oscillator is done
+	  via I2C.
+
+config COMMON_CLK_IDT8T49N24X
+	tristate "Clock driver for IDT 8T49N24x"
+	depends on I2C
+	depends on OF
+	select REGMAP_I2C
+	help
+	---help---
+	  This driver supports the IDT 8T49N24x universal frequency translator
+	  product family.  The only chip in the family that is currently
+	  supported is the 8T49N241. The driver supports setting the rate for
+	  all four outputs on the chip and automatically calculating/setting
+	  the appropriate VCO value.
+
+	  The driver can read a full register map from the DT,
+	  and will use that register map to initialize the attached part
+	  (via I2C) when the system boots. Any configuration not supported
+	  by the common clock framework must be done via the full register
+	  map, including optimized settings.
+
+	  All outputs are currently assumed to be LVDS, unless overridden
+	  in the full register map in the DT.
+
 config COMMON_CLK_CDCE706
 	tristate "Clock driver for TI CDCE706 clock synthesizer"
 	depends on I2C
@@ -334,6 +366,15 @@
 	  This driver supports the IDT VersaClock 5 and VersaClock 6
 	  programmable clock generators.
 
+config COMMON_CLK_VC7
+	tristate "Clock driver for Renesas Versaclock 7 devices"
+	depends on I2C
+	depends on OF
+	select REGMAP_I2C
+	help
+	  Renesas Versaclock7 is a family of configurable clock generator
+	  and jitter attenuator ICs with fractional and integer dividers.
+
 config COMMON_CLK_STM32MP157
 	def_bool COMMON_CLK && MACH_STM32MP157
 	help
@@ -380,6 +421,7 @@
 config COMMON_CLK_FIXED_MMIO
 	bool "Clock driver for Memory Mapped Fixed values"
 	depends on COMMON_CLK && OF
+	depends on HAS_IOMEM
 	help
 	  Support for Memory Mapped IO Fixed clocks
 
@@ -390,6 +432,21 @@
 	help
 	  Support for the Canaan Kendryte K210 RISC-V SoC clocks.
 
+config COMMON_CLK_XLNX_CLKWZRD
+	tristate "Xilinx Clocking Wizard"
+	depends on COMMON_CLK && OF
+	help
+	  Support for the Xilinx Clocking Wizard IP core clock generator.
+
+config COMMON_CLK_XLNX_CLKWZRD_V
+	tristate "Xilinx Versal Clocking Wizard"
+	depends on COMMON_CLK && OF
+	help
+	  Support for the Versal Xilinx Clocking Wizard IP core clock generator.
+	  Adds support for Versal clocking wizard 1.0 and compatible.
+	  This driver supports the Xilinx clocking wizard programmable clock
+	  synthesizer. The number of output is configurable in the design.
+
 source "drivers/clk/actions/Kconfig"
 source "drivers/clk/analogbits/Kconfig"
 source "drivers/clk/baikal-t1/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/Makefile
@@ -63,11 +63,16 @@
 obj-$(CONFIG_COMMON_CLK_STM32F)		+= clk-stm32f4.o
 obj-$(CONFIG_COMMON_CLK_STM32H7)	+= clk-stm32h7.o
 obj-$(CONFIG_COMMON_CLK_STM32MP157)	+= clk-stm32mp1.o
+clk-si5324drv-y				:= si5324drv.o clk-si5324.o
+obj-$(CONFIG_COMMON_CLK_SI5324)		+= clk-si5324drv.o
 obj-$(CONFIG_CLK_TWL6040)		+= clk-twl6040.o
 obj-$(CONFIG_ARCH_VT8500)		+= clk-vt8500.o
 obj-$(CONFIG_COMMON_CLK_VC5)		+= clk-versaclock5.o
+obj-$(CONFIG_COMMON_CLK_VC7)		+= clk-versaclock7.o
 obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
 obj-$(CONFIG_COMMON_CLK_XGENE)		+= clk-xgene.o
+obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD)	+= clk-xlnx-clock-wizard.o
+obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD_V)	+= clk-xlnx-clock-wizard-v.o
 
 # please keep this section sorted lexicographically by directory path name
 obj-y					+= actions/
@@ -81,6 +86,7 @@
 obj-$(CONFIG_ARCH_DAVINCI)		+= davinci/
 obj-$(CONFIG_H8300)			+= h8300/
 obj-$(CONFIG_ARCH_HISI)			+= hisilicon/
+obj-$(CONFIG_COMMON_CLK_IDT8T49N24X)	+= idt/
 obj-y					+= imgtec/
 obj-y					+= imx/
 obj-y					+= ingenic/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/actions/owl-s700.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/actions/owl-s700.c
@@ -162,6 +162,7 @@
 
 static struct clk_div_table rmii_div_table[] = {
 	{0, 4},   {1, 10},
+	{0, 0}
 };
 
 /* divider clocks */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/actions/owl-s900.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/actions/owl-s900.c
@@ -140,7 +140,7 @@
 
 static struct clk_div_table usb3_mac_div_table[] = {
 	{ 1, 2 }, { 2, 3 }, { 3, 4 },
-	{ 0, 8 },
+	{ 0, 0 }
 };
 
 static struct clk_div_table i2s_div_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/analogbits/wrpll-cln28hpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/analogbits/wrpll-cln28hpc.c
@@ -291,7 +291,7 @@
 			vco = vco_pre * f;
 		}
 
-		delta = abs(target_rate - vco);
+		delta = abs(target_vco_rate - vco);
 		if (delta < best_delta) {
 			best_delta = delta;
 			best_r = r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/at91/at91rm9200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/at91/at91rm9200.c
@@ -40,7 +40,7 @@
 };
 
 static const struct sck at91rm9200_systemck[] = {
-	{ .n = "udpck", .p = "usbck",    .id = 2 },
+	{ .n = "udpck", .p = "usbck",    .id = 1 },
 	{ .n = "uhpck", .p = "usbck",    .id = 4 },
 	{ .n = "pck0",  .p = "prog0",    .id = 8 },
 	{ .n = "pck1",  .p = "prog1",    .id = 9 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/at91/clk-generated.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/at91/clk-generated.c
@@ -106,6 +106,10 @@
 		tmp_rate = parent_rate;
 	else
 		tmp_rate = parent_rate / div;
+
+	if (tmp_rate < req->min_rate || tmp_rate > req->max_rate)
+		return;
+
 	tmp_diff = abs(req->rate - tmp_rate);
 
 	if (*best_diff < 0 || *best_diff >= tmp_diff) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/at91/clk-master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/at91/clk-master.c
@@ -280,7 +280,7 @@
 
 	else if (pres == 3)
 		pres = MASTER_PRES_MAX;
-	else
+	else if (pres)
 		pres = ffs(pres) - 1;
 
 	spin_lock_irqsave(master->lock, flags);
@@ -309,7 +309,7 @@
 	spin_unlock_irqrestore(master->lock, flags);
 
 	pres = (val >> master->layout->pres_shift) & MASTER_PRES_MASK;
-	if (pres == 3 && characteristics->have_div3_pres)
+	if (pres == MASTER_PRES_MAX && characteristics->have_div3_pres)
 		pres = 3;
 	else
 		pres = (1 << pres);
@@ -610,7 +610,7 @@
 
 	if (div == 3)
 		div = MASTER_PRES_MAX;
-	else
+	else if (div)
 		div = ffs(div) - 1;
 
 	spin_lock_irqsave(master->lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/at91/clk-sam9x60-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/at91/clk-sam9x60-pll.c
@@ -71,8 +71,8 @@
 	struct sam9x60_pll_core *core = to_sam9x60_pll_core(hw);
 	struct sam9x60_frac *frac = to_sam9x60_frac(core);
 
-	return (parent_rate * (frac->mul + 1) +
-		((u64)parent_rate * frac->frac >> 22));
+	return parent_rate * (frac->mul + 1) +
+		DIV_ROUND_CLOSEST_ULL((u64)parent_rate * frac->frac, (1 << 22));
 }
 
 static int sam9x60_frac_pll_prepare(struct clk_hw *hw)
@@ -561,7 +561,7 @@
 
 		ret = sam9x60_frac_pll_compute_mul_frac(&frac->core, FCORE_MIN,
 							parent_rate, true);
-		if (ret <= 0) {
+		if (ret < 0) {
 			hw = ERR_PTR(ret);
 			goto free;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/at91/pmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/at91/pmc.c
@@ -267,6 +267,11 @@
 	if (!np)
 		return -ENODEV;
 
+	if (!of_device_is_available(np)) {
+		of_node_put(np);
+		return -ENODEV;
+	}
+
 	pmcreg = device_node_to_regmap(np);
 	of_node_put(np);
 	if (IS_ERR(pmcreg))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/at91/sama7g5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/at91/sama7g5.c
@@ -687,16 +687,16 @@
 	{ .n  = "pdmc0_gclk",
 	  .id = 68,
 	  .r = { .max = 50000000  },
-	  .pp = { "syspll_divpmcck", "baudpll_divpmcck", },
-	  .pp_mux_table = { 5, 8, },
+	  .pp = { "syspll_divpmcck", "audiopll_divpmcck", },
+	  .pp_mux_table = { 5, 9, },
 	  .pp_count = 2,
 	  .pp_chg_id = INT_MIN, },
 
 	{ .n  = "pdmc1_gclk",
 	  .id = 69,
 	  .r = { .max = 50000000, },
-	  .pp = { "syspll_divpmcck", "baudpll_divpmcck", },
-	  .pp_mux_table = { 5, 8, },
+	  .pp = { "syspll_divpmcck", "audiopll_divpmcck", },
+	  .pp_mux_table = { 5, 9, },
 	  .pp_count = 2,
 	  .pp_chg_id = INT_MIN, },
 
@@ -982,16 +982,7 @@
 	}
 
 	parent_names[0] = "cpupll_divpmcck";
-	hw = at91_clk_register_master_pres(regmap, "cpuck", 1, parent_names,
-					   &mck0_layout, &mck0_characteristics,
-					   &pmc_mck0_lock,
-					   CLK_SET_RATE_PARENT, 0);
-	if (IS_ERR(hw))
-		goto err_free;
-
-	sama7g5_pmc->chws[PMC_CPU] = hw;
-
-	hw = at91_clk_register_master_div(regmap, "mck0", "cpuck",
+	hw = at91_clk_register_master_div(regmap, "mck0", "cpupll_divpmcck",
 					  &mck0_layout, &mck0_characteristics,
 					  &pmc_mck0_lock, 0);
 	if (IS_ERR(hw))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/baikal-t1/ccu-div.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/baikal-t1/ccu-div.c
@@ -34,6 +34,7 @@
 #define CCU_DIV_CTL_CLKDIV_MASK(_width) \
 	GENMASK((_width) + CCU_DIV_CTL_CLKDIV_FLD - 1, CCU_DIV_CTL_CLKDIV_FLD)
 #define CCU_DIV_CTL_LOCK_SHIFTED	BIT(27)
+#define CCU_DIV_CTL_GATE_REF_BUF	BIT(28)
 #define CCU_DIV_CTL_LOCK_NORMAL		BIT(31)
 
 #define CCU_DIV_RST_DELAY_US		1
@@ -170,6 +171,40 @@
 	return !!(val & CCU_DIV_CTL_EN);
 }
 
+static int ccu_div_buf_enable(struct clk_hw *hw)
+{
+	struct ccu_div *div = to_ccu_div(hw);
+	unsigned long flags;
+
+	spin_lock_irqsave(&div->lock, flags);
+	regmap_update_bits(div->sys_regs, div->reg_ctl,
+			   CCU_DIV_CTL_GATE_REF_BUF, 0);
+	spin_unlock_irqrestore(&div->lock, flags);
+
+	return 0;
+}
+
+static void ccu_div_buf_disable(struct clk_hw *hw)
+{
+	struct ccu_div *div = to_ccu_div(hw);
+	unsigned long flags;
+
+	spin_lock_irqsave(&div->lock, flags);
+	regmap_update_bits(div->sys_regs, div->reg_ctl,
+			   CCU_DIV_CTL_GATE_REF_BUF, CCU_DIV_CTL_GATE_REF_BUF);
+	spin_unlock_irqrestore(&div->lock, flags);
+}
+
+static int ccu_div_buf_is_enabled(struct clk_hw *hw)
+{
+	struct ccu_div *div = to_ccu_div(hw);
+	u32 val = 0;
+
+	regmap_read(div->sys_regs, div->reg_ctl, &val);
+
+	return !(val & CCU_DIV_CTL_GATE_REF_BUF);
+}
+
 static unsigned long ccu_div_var_recalc_rate(struct clk_hw *hw,
 					     unsigned long parent_rate)
 {
@@ -323,6 +358,7 @@
 	CCU_DIV_DBGFS_BIT_ATTR("div_en", CCU_DIV_CTL_EN),
 	CCU_DIV_DBGFS_BIT_ATTR("div_rst", CCU_DIV_CTL_RST),
 	CCU_DIV_DBGFS_BIT_ATTR("div_bypass", CCU_DIV_CTL_SET_CLKDIV),
+	CCU_DIV_DBGFS_BIT_ATTR("div_buf", CCU_DIV_CTL_GATE_REF_BUF),
 	CCU_DIV_DBGFS_BIT_ATTR("div_lock", CCU_DIV_CTL_LOCK_NORMAL)
 };
 
@@ -441,6 +477,9 @@
 			continue;
 		}
 
+		if (!strcmp("div_buf", name))
+			continue;
+
 		bits[didx] = ccu_div_bits[bidx];
 		bits[didx].div = div;
 
@@ -477,6 +516,21 @@
 				   &ccu_div_dbgfs_fixed_clkdiv_fops);
 }
 
+static void ccu_div_buf_debug_init(struct clk_hw *hw, struct dentry *dentry)
+{
+	struct ccu_div *div = to_ccu_div(hw);
+	struct ccu_div_dbgfs_bit *bit;
+
+	bit = kmalloc(sizeof(*bit), GFP_KERNEL);
+	if (!bit)
+		return;
+
+	*bit = ccu_div_bits[3];
+	bit->div = div;
+	debugfs_create_file_unsafe(bit->name, ccu_div_dbgfs_mode, dentry, bit,
+				   &ccu_div_dbgfs_bit_fops);
+}
+
 static void ccu_div_fixed_debug_init(struct clk_hw *hw, struct dentry *dentry)
 {
 	struct ccu_div *div = to_ccu_div(hw);
@@ -489,6 +543,7 @@
 
 #define ccu_div_var_debug_init NULL
 #define ccu_div_gate_debug_init NULL
+#define ccu_div_buf_debug_init NULL
 #define ccu_div_fixed_debug_init NULL
 
 #endif /* !CONFIG_DEBUG_FS */
@@ -520,6 +575,13 @@
 	.debug_init = ccu_div_gate_debug_init
 };
 
+static const struct clk_ops ccu_div_buf_ops = {
+	.enable = ccu_div_buf_enable,
+	.disable = ccu_div_buf_disable,
+	.is_enabled = ccu_div_buf_is_enabled,
+	.debug_init = ccu_div_buf_debug_init
+};
+
 static const struct clk_ops ccu_div_fixed_ops = {
 	.recalc_rate = ccu_div_fixed_recalc_rate,
 	.round_rate = ccu_div_fixed_round_rate,
@@ -566,6 +628,8 @@
 	} else if (div_init->type == CCU_DIV_GATE) {
 		hw_init.ops = &ccu_div_gate_ops;
 		div->divider = div_init->divider;
+	} else if (div_init->type == CCU_DIV_BUF) {
+		hw_init.ops = &ccu_div_buf_ops;
 	} else if (div_init->type == CCU_DIV_FIXED) {
 		hw_init.ops = &ccu_div_fixed_ops;
 		div->divider = div_init->divider;
@@ -579,6 +643,7 @@
 		goto err_free_div;
 	}
 	parent_data.fw_name = div_init->parent_name;
+	parent_data.name = div_init->parent_name;
 	hw_init.parent_data = &parent_data;
 	hw_init.num_parents = 1;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/baikal-t1/ccu-div.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/baikal-t1/ccu-div.h
@@ -14,6 +14,14 @@
 #include <linux/of.h>
 
 /*
+ * CCU Divider private clock IDs
+ * @CCU_SYS_SATA_CLK: CCU SATA internal clock
+ * @CCU_SYS_XGMAC_CLK: CCU XGMAC internal clock
+ */
+#define CCU_SYS_SATA_CLK		-1
+#define CCU_SYS_XGMAC_CLK		-2
+
+/*
  * CCU Divider private flags
  * @CCU_DIV_SKIP_ONE: Due to some reason divider can't be set to 1.
  *		      It can be 0 though, which is functionally the same.
@@ -31,11 +39,13 @@
  * enum ccu_div_type - CCU Divider types
  * @CCU_DIV_VAR: Clocks gate with variable divider.
  * @CCU_DIV_GATE: Clocks gate with fixed divider.
+ * @CCU_DIV_BUF: Clock gate with no divider.
  * @CCU_DIV_FIXED: Ungateable clock with fixed divider.
  */
 enum ccu_div_type {
 	CCU_DIV_VAR,
 	CCU_DIV_GATE,
+	CCU_DIV_BUF,
 	CCU_DIV_FIXED
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/baikal-t1/clk-ccu-div.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/baikal-t1/clk-ccu-div.c
@@ -76,6 +76,16 @@
 		.divider = _divider				\
 	}
 
+#define CCU_DIV_BUF_INFO(_id, _name, _pname, _base, _flags)	\
+	{							\
+		.id = _id,					\
+		.name = _name,					\
+		.parent_name = _pname,				\
+		.base = _base,					\
+		.type = CCU_DIV_BUF,				\
+		.flags = _flags					\
+	}
+
 #define CCU_DIV_FIXED_INFO(_id, _name, _pname, _divider)	\
 	{							\
 		.id = _id,					\
@@ -188,11 +198,14 @@
  * for the SoC devices registers IO-operations.
  */
 static const struct ccu_div_info sys_info[] = {
-	CCU_DIV_VAR_INFO(CCU_SYS_SATA_REF_CLK, "sys_sata_ref_clk",
+	CCU_DIV_VAR_INFO(CCU_SYS_SATA_CLK, "sys_sata_clk",
 			 "sata_clk", CCU_SYS_SATA_REF_BASE, 4,
 			 CLK_SET_RATE_GATE,
 			 CCU_DIV_SKIP_ONE | CCU_DIV_LOCK_SHIFTED |
 			 CCU_DIV_RESET_DOMAIN),
+	CCU_DIV_BUF_INFO(CCU_SYS_SATA_REF_CLK, "sys_sata_ref_clk",
+			 "sys_sata_clk", CCU_SYS_SATA_REF_BASE,
+			 CLK_SET_RATE_PARENT),
 	CCU_DIV_VAR_INFO(CCU_SYS_APB_CLK, "sys_apb_clk",
 			 "pcie_clk", CCU_SYS_APB_BASE, 5,
 			 CLK_IS_CRITICAL, CCU_DIV_RESET_DOMAIN),
@@ -204,10 +217,12 @@
 			  "eth_clk", CCU_SYS_GMAC1_BASE, 5),
 	CCU_DIV_FIXED_INFO(CCU_SYS_GMAC1_PTP_CLK, "sys_gmac1_ptp_clk",
 			   "eth_clk", 10),
-	CCU_DIV_GATE_INFO(CCU_SYS_XGMAC_REF_CLK, "sys_xgmac_ref_clk",
-			  "eth_clk", CCU_SYS_XGMAC_BASE, 8),
+	CCU_DIV_GATE_INFO(CCU_SYS_XGMAC_CLK, "sys_xgmac_clk",
+			  "eth_clk", CCU_SYS_XGMAC_BASE, 1),
+	CCU_DIV_FIXED_INFO(CCU_SYS_XGMAC_REF_CLK, "sys_xgmac_ref_clk",
+			   "sys_xgmac_clk", 8),
 	CCU_DIV_FIXED_INFO(CCU_SYS_XGMAC_PTP_CLK, "sys_xgmac_ptp_clk",
-			   "eth_clk", 10),
+			   "sys_xgmac_clk", 8),
 	CCU_DIV_GATE_INFO(CCU_SYS_USB_CLK, "sys_usb_clk",
 			  "eth_clk", CCU_SYS_USB_BASE, 10),
 	CCU_DIV_VAR_INFO(CCU_SYS_PVT_CLK, "sys_pvt_clk",
@@ -396,6 +411,9 @@
 			init.base = info->base;
 			init.sys_regs = data->sys_regs;
 			init.divider = info->divider;
+		} else if (init.type == CCU_DIV_BUF) {
+			init.base = info->base;
+			init.sys_regs = data->sys_regs;
 		} else {
 			init.divider = info->divider;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/bcm/clk-bcm2835.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/bcm/clk-bcm2835.c
@@ -30,6 +30,7 @@
 #include <linux/debugfs.h>
 #include <linux/delay.h>
 #include <linux/io.h>
+#include <linux/math.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
@@ -502,6 +503,8 @@
 	bool low_jitter;
 
 	u32 tcnt_mux;
+
+	bool round_up;
 };
 
 struct bcm2835_gate_data {
@@ -932,8 +935,7 @@
 
 static u32 bcm2835_clock_choose_div(struct clk_hw *hw,
 				    unsigned long rate,
-				    unsigned long parent_rate,
-				    bool round_up)
+				    unsigned long parent_rate)
 {
 	struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
 	const struct bcm2835_clock_data *data = clock->data;
@@ -945,10 +947,6 @@
 
 	rem = do_div(temp, rate);
 	div = temp;
-
-	/* Round up and mask off the unused bits */
-	if (round_up && ((div & unused_frac_mask) != 0 || rem != 0))
-		div += unused_frac_mask + 1;
 	div &= ~unused_frac_mask;
 
 	/* different clamping limits apply for a mash clock */
@@ -972,9 +970,9 @@
 	return div;
 }
 
-static long bcm2835_clock_rate_from_divisor(struct bcm2835_clock *clock,
-					    unsigned long parent_rate,
-					    u32 div)
+static unsigned long bcm2835_clock_rate_from_divisor(struct bcm2835_clock *clock,
+						     unsigned long parent_rate,
+						     u32 div)
 {
 	const struct bcm2835_clock_data *data = clock->data;
 	u64 temp;
@@ -999,12 +997,34 @@
 	return temp;
 }
 
+static unsigned long bcm2835_round_rate(unsigned long rate)
+{
+	unsigned long scaler;
+	unsigned long limit;
+
+	limit = rate / 100000;
+
+	scaler = 1;
+	while (scaler < limit)
+		scaler *= 10;
+
+	/*
+	 * If increasing a clock by less than 0.1% changes it
+	 * from ..999.. to ..000.., round up.
+	 */
+	if ((rate + scaler - 1) / scaler % 1000 == 0)
+		rate = roundup(rate, scaler);
+
+	return rate;
+}
+
 static unsigned long bcm2835_clock_get_rate(struct clk_hw *hw,
 					    unsigned long parent_rate)
 {
 	struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
 	struct bcm2835_cprman *cprman = clock->cprman;
 	const struct bcm2835_clock_data *data = clock->data;
+	unsigned long rate;
 	u32 div;
 
 	if (data->int_bits == 0 && data->frac_bits == 0)
@@ -1012,7 +1032,12 @@
 
 	div = cprman_read(cprman, data->div_reg);
 
-	return bcm2835_clock_rate_from_divisor(clock, parent_rate, div);
+	rate = bcm2835_clock_rate_from_divisor(clock, parent_rate, div);
+
+	if (data->round_up)
+		rate = bcm2835_round_rate(rate);
+
+	return rate;
 }
 
 static void bcm2835_clock_wait_busy(struct bcm2835_clock *clock)
@@ -1079,7 +1104,7 @@
 	struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
 	struct bcm2835_cprman *cprman = clock->cprman;
 	const struct bcm2835_clock_data *data = clock->data;
-	u32 div = bcm2835_clock_choose_div(hw, rate, parent_rate, false);
+	u32 div = bcm2835_clock_choose_div(hw, rate, parent_rate);
 	u32 ctl;
 
 	spin_lock(&cprman->regs_lock);
@@ -1130,7 +1155,7 @@
 
 	if (!(BIT(parent_idx) & data->set_rate_parent)) {
 		*prate = clk_hw_get_rate(parent);
-		*div = bcm2835_clock_choose_div(hw, rate, *prate, true);
+		*div = bcm2835_clock_choose_div(hw, rate, *prate);
 
 		*avgrate = bcm2835_clock_rate_from_divisor(clock, *prate, *div);
 
@@ -1216,7 +1241,7 @@
 		rate = bcm2835_clock_choose_div_and_prate(hw, i, req->rate,
 							  &div, &prate,
 							  &avgrate);
-		if (rate > best_rate && rate <= req->rate) {
+		if (abs(req->rate - rate) < abs(req->rate - best_rate)) {
 			best_parent = parent;
 			best_prate = prate;
 			best_rate = rate;
@@ -1790,7 +1815,7 @@
 		.load_mask = CM_PLLC_LOADPER,
 		.hold_mask = CM_PLLC_HOLDPER,
 		.fixed_divider = 1,
-		.flags = CLK_SET_RATE_PARENT),
+		.flags = CLK_IS_CRITICAL | CLK_SET_RATE_PARENT),
 
 	/*
 	 * PLLD is the display PLL, used to drive DSI display panels.
@@ -2149,7 +2174,8 @@
 		.div_reg = CM_UARTDIV,
 		.int_bits = 10,
 		.frac_bits = 12,
-		.tcnt_mux = 28),
+		.tcnt_mux = 28,
+		.round_up = true),
 
 	/* TV encoder clock.  Only operating frequency is 108Mhz.  */
 	[BCM2835_CLOCK_VEC]	= REGISTER_PER_CLK(
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/bcm/clk-bcm53573-ilp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/bcm/clk-bcm53573-ilp.c
@@ -112,7 +112,7 @@
 		goto err_free_ilp;
 	}
 
-	ilp->regmap = syscon_node_to_regmap(of_get_parent(np));
+	ilp->regmap = syscon_node_to_regmap(np->parent);
 	if (IS_ERR(ilp->regmap)) {
 		err = PTR_ERR(ilp->regmap);
 		goto err_free_ilp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/bcm/clk-iproc-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/bcm/clk-iproc-pll.c
@@ -736,6 +736,7 @@
 	const char *parent_name;
 	struct iproc_clk *iclk_array;
 	struct clk_hw_onecell_data *clk_data;
+	const char *clk_name;
 
 	if (WARN_ON(!pll_ctrl) || WARN_ON(!clk_ctrl))
 		return;
@@ -783,7 +784,12 @@
 	iclk = &iclk_array[0];
 	iclk->pll = pll;
 
-	init.name = node->name;
+	ret = of_property_read_string_index(node, "clock-output-names",
+					    0, &clk_name);
+	if (WARN_ON(ret))
+		goto err_pll_register;
+
+	init.name = clk_name;
 	init.ops = &iproc_pll_ops;
 	init.flags = 0;
 	parent_name = of_clk_get_parent_name(node, 0);
@@ -803,13 +809,11 @@
 		goto err_pll_register;
 
 	clk_data->hws[0] = &iclk->hw;
+	parent_name = clk_name;
 
 	/* now initialize and register all leaf clocks */
 	for (i = 1; i < num_clks; i++) {
-		const char *clk_name;
-
 		memset(&init, 0, sizeof(init));
-		parent_name = node->name;
 
 		ret = of_property_read_string_index(node, "clock-output-names",
 						    i, &clk_name);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/bcm/clk-raspberrypi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/bcm/clk-raspberrypi.c
@@ -139,7 +139,7 @@
 	ret = raspberrypi_clock_property(rpi->firmware, data,
 					 RPI_FIRMWARE_GET_CLOCK_RATE, &val);
 	if (ret)
-		return ret;
+		return 0;
 
 	return val;
 }
@@ -156,7 +156,7 @@
 	ret = raspberrypi_clock_property(rpi->firmware, data,
 					 RPI_FIRMWARE_SET_CLOCK_RATE, &_rate);
 	if (ret)
-		dev_err_ratelimited(rpi->dev, "Failed to change %s frequency: %d",
+		dev_err_ratelimited(rpi->dev, "Failed to change %s frequency: %d\n",
 				    clk_hw_get_name(hw), ret);
 
 	return ret;
@@ -208,7 +208,7 @@
 					 RPI_FIRMWARE_GET_MIN_CLOCK_RATE,
 					 &min_rate);
 	if (ret) {
-		dev_err(rpi->dev, "Failed to get clock %d min freq: %d",
+		dev_err(rpi->dev, "Failed to get clock %d min freq: %d\n",
 			id, ret);
 		return ERR_PTR(ret);
 	}
@@ -251,8 +251,13 @@
 	struct rpi_firmware_get_clocks_response *clks;
 	int ret;
 
+	/*
+	 * The firmware doesn't guarantee that the last element of
+	 * RPI_FIRMWARE_GET_CLOCKS is zeroed. So allocate an additional
+	 * zero element as sentinel.
+	 */
 	clks = devm_kcalloc(rpi->dev,
-			    sizeof(*clks), RPI_FIRMWARE_NUM_CLK_ID,
+			    RPI_FIRMWARE_NUM_CLK_ID + 1, sizeof(*clks),
 			    GFP_KERNEL);
 	if (!clks)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/berlin/bg2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/berlin/bg2.c
@@ -500,12 +500,15 @@
 	int n, ret;
 
 	clk_data = kzalloc(struct_size(clk_data, hws, MAX_CLKS), GFP_KERNEL);
-	if (!clk_data)
+	if (!clk_data) {
+		of_node_put(parent_np);
 		return;
+	}
 	clk_data->num = MAX_CLKS;
 	hws = clk_data->hws;
 
 	gbase = of_iomap(parent_np, 0);
+	of_node_put(parent_np);
 	if (!gbase)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/berlin/bg2q.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/berlin/bg2q.c
@@ -286,19 +286,23 @@
 	int n, ret;
 
 	clk_data = kzalloc(struct_size(clk_data, hws, MAX_CLKS), GFP_KERNEL);
-	if (!clk_data)
+	if (!clk_data) {
+		of_node_put(parent_np);
 		return;
+	}
 	clk_data->num = MAX_CLKS;
 	hws = clk_data->hws;
 
 	gbase = of_iomap(parent_np, 0);
 	if (!gbase) {
+		of_node_put(parent_np);
 		pr_err("%pOF: Unable to map global base\n", np);
 		return;
 	}
 
 	/* BG2Q CPU PLL is not part of global registers */
 	cpupll_base = of_iomap(parent_np, 1);
+	of_node_put(parent_np);
 	if (!cpupll_base) {
 		pr_err("%pOF: Unable to map cpupll base\n", np);
 		iounmap(gbase);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-asm9260.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-asm9260.c
@@ -80,7 +80,7 @@
 	u8			mask;
 	u32			*table;
 	const char		*name;
-	const char		**parent_names;
+	const struct clk_parent_data *parent_data;
 	u8			num_parents;
 	unsigned long		offset;
 	unsigned long		flags;
@@ -232,10 +232,10 @@
 		HW_AHBCLKCTRL1,	16 },
 };
 
-static const char __initdata *main_mux_p[] =   { NULL, NULL };
-static const char __initdata *i2s0_mux_p[] =   { NULL, NULL, "i2s0m_div"};
-static const char __initdata *i2s1_mux_p[] =   { NULL, NULL, "i2s1m_div"};
-static const char __initdata *clkout_mux_p[] = { NULL, NULL, "rtc"};
+static struct clk_parent_data __initdata main_mux_p[] =   { { .index = 0, }, { .name = "pll" } };
+static struct clk_parent_data __initdata i2s0_mux_p[] =   { { .index = 0, }, { .name = "pll" }, { .name = "i2s0m_div"} };
+static struct clk_parent_data __initdata i2s1_mux_p[] =   { { .index = 0, }, { .name = "pll" }, { .name = "i2s1m_div"} };
+static struct clk_parent_data __initdata clkout_mux_p[] = { { .index = 0, }, { .name = "pll" }, { .name = "rtc"} };
 static u32 three_mux_table[] = {0, 1, 3};
 
 static struct asm9260_mux_clock asm9260_mux_clks[] __initdata = {
@@ -255,9 +255,10 @@
 
 static void __init asm9260_acc_init(struct device_node *np)
 {
-	struct clk_hw *hw;
+	struct clk_hw *hw, *pll_hw;
 	struct clk_hw **hws;
-	const char *ref_clk, *pll_clk = "pll";
+	const char *pll_clk = "pll";
+	struct clk_parent_data pll_parent_data = { .index = 0 };
 	u32 rate;
 	int n;
 
@@ -274,21 +275,15 @@
 	/* register pll */
 	rate = (ioread32(base + HW_SYSPLLCTRL) & 0xffff) * 1000000;
 
-	/* TODO: Convert to DT parent scheme */
-	ref_clk = of_clk_get_parent_name(np, 0);
-	hw = __clk_hw_register_fixed_rate(NULL, NULL, pll_clk,
-			ref_clk, NULL, NULL, 0, rate, 0,
-			CLK_FIXED_RATE_PARENT_ACCURACY);
-
-	if (IS_ERR(hw))
+	pll_hw = clk_hw_register_fixed_rate_parent_accuracy(NULL, pll_clk, &pll_parent_data,
+							0, rate);
+	if (IS_ERR(pll_hw))
 		panic("%pOFn: can't register REFCLK. Check DT!", np);
 
 	for (n = 0; n < ARRAY_SIZE(asm9260_mux_clks); n++) {
 		const struct asm9260_mux_clock *mc = &asm9260_mux_clks[n];
 
-		mc->parent_names[0] = ref_clk;
-		mc->parent_names[1] = pll_clk;
-		hw = clk_hw_register_mux_table(NULL, mc->name, mc->parent_names,
+		hw = clk_hw_register_mux_table_parent_data(NULL, mc->name, mc->parent_data,
 				mc->num_parents, mc->flags, base + mc->offset,
 				0, mc->mask, 0, mc->table, &asm9260_clk_lock);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-ast2600.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-ast2600.c
@@ -51,6 +51,8 @@
 static struct clk_hw_onecell_data *aspeed_g6_clk_data;
 
 static void __iomem *scu_g6_base;
+/* AST2600 revision: A0, A1, A2, etc */
+static u8 soc_rev;
 
 /*
  * Clocks marked with CLK_IS_CRITICAL:
@@ -191,9 +193,8 @@
 static struct clk_hw *ast2600_calc_apll(const char *name, u32 val)
 {
 	unsigned int mult, div;
-	u32 chip_id = readl(scu_g6_base + ASPEED_G6_SILICON_REV);
 
-	if (((chip_id & CHIP_REVISION_ID) >> 16) >= 2) {
+	if (soc_rev >= 2) {
 		if (val & BIT(24)) {
 			/* Pass through mode */
 			mult = div = 1;
@@ -621,7 +622,7 @@
 	regmap_write(map, 0x308, 0x12000); /* 3x3 = 9 */
 
 	/* P-Bus (BCLK) clock divider */
-	hw = clk_hw_register_divider_table(dev, "bclk", "hpll", 0,
+	hw = clk_hw_register_divider_table(dev, "bclk", "epll", 0,
 			scu_g6_base + ASPEED_G6_CLK_SELECTION1, 20, 3, 0,
 			ast2600_div_table,
 			&aspeed_g6_clk_lock);
@@ -707,7 +708,7 @@
 static void __init aspeed_g6_cc(struct regmap *map)
 {
 	struct clk_hw *hw;
-	u32 val, div, divbits, chip_id, axi_div, ahb_div;
+	u32 val, div, divbits, axi_div, ahb_div;
 
 	clk_hw_register_fixed_rate(NULL, "clkin", NULL, 0, 25000000);
 
@@ -738,8 +739,7 @@
 		axi_div = 2;
 
 	divbits = (val >> 11) & 0x3;
-	regmap_read(map, ASPEED_G6_SILICON_REV, &chip_id);
-	if (chip_id & BIT(16)) {
+	if (soc_rev >= 1) {
 		if (!divbits) {
 			ahb_div = ast2600_a1_axi_ahb200_tbl[(val >> 8) & 0x3];
 			if (val & BIT(16))
@@ -784,6 +784,8 @@
 	if (!scu_g6_base)
 		return;
 
+	soc_rev = (readl(scu_g6_base + ASPEED_G6_SILICON_REV) & CHIP_REVISION_ID) >> 16;
+
 	aspeed_g6_clk_data = kzalloc(struct_size(aspeed_g6_clk_data, hws,
 				      ASPEED_G6_NUM_CLKS), GFP_KERNEL);
 	if (!aspeed_g6_clk_data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-axi-clkgen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-axi-clkgen.c
@@ -7,6 +7,7 @@
  */
 
 #include <linux/platform_device.h>
+#include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/slab.h>
 #include <linux/io.h>
@@ -510,6 +511,7 @@
 	struct clk_init_data init;
 	const char *parent_names[2];
 	const char *clk_name;
+	struct clk *axi_clk;
 	unsigned int i;
 	int ret;
 
@@ -526,8 +528,24 @@
 		return PTR_ERR(axi_clkgen->base);
 
 	init.num_parents = of_clk_get_parent_count(pdev->dev.of_node);
-	if (init.num_parents < 1 || init.num_parents > 2)
-		return -EINVAL;
+
+	axi_clk = devm_clk_get_enabled(&pdev->dev, "s_axi_aclk");
+	if (!IS_ERR(axi_clk)) {
+		if (init.num_parents < 2 || init.num_parents > 3)
+			return -EINVAL;
+
+		init.num_parents -= 1;
+	} else {
+		/*
+		 * Legacy... So that old DTs which do not have clock-names still
+		 * work. In this case we don't explicitly enable the AXI bus
+		 * clock.
+		 */
+		if (PTR_ERR(axi_clk) != -ENOENT)
+			return PTR_ERR(axi_clk);
+		if (init.num_parents < 1 || init.num_parents > 2)
+			return -EINVAL;
+	}
 
 	for (i = 0; i < init.num_parents; i++) {
 		parent_names[i] = of_clk_get_parent_name(pdev->dev.of_node, i);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-bm1880.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-bm1880.c
@@ -522,14 +522,6 @@
 	return hw;
 }
 
-static void bm1880_clk_unregister_pll(struct clk_hw *hw)
-{
-	struct bm1880_pll_hw_clock *pll_hw = to_bm1880_pll_clk(hw);
-
-	clk_hw_unregister(hw);
-	kfree(pll_hw);
-}
-
 static int bm1880_clk_register_plls(struct bm1880_pll_hw_clock *clks,
 				    int num_clks,
 				    struct bm1880_clock_data *data)
@@ -555,7 +547,7 @@
 
 err_clk:
 	while (i--)
-		bm1880_clk_unregister_pll(data->hw_data.hws[clks[i].pll.id]);
+		clk_hw_unregister(data->hw_data.hws[clks[i].pll.id]);
 
 	return PTR_ERR(hw);
 }
@@ -695,14 +687,6 @@
 	return hw;
 }
 
-static void bm1880_clk_unregister_div(struct clk_hw *hw)
-{
-	struct bm1880_div_hw_clock *div_hw = to_bm1880_div_clk(hw);
-
-	clk_hw_unregister(hw);
-	kfree(div_hw);
-}
-
 static int bm1880_clk_register_divs(struct bm1880_div_hw_clock *clks,
 				    int num_clks,
 				    struct bm1880_clock_data *data)
@@ -729,7 +713,7 @@
 
 err_clk:
 	while (i--)
-		bm1880_clk_unregister_div(data->hw_data.hws[clks[i].div.id]);
+		clk_hw_unregister(data->hw_data.hws[clks[i].div.id]);
 
 	return PTR_ERR(hw);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-cdce925.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-cdce925.c
@@ -705,6 +705,10 @@
 	for (i = 0; i < data->chip_info->num_plls; ++i) {
 		pll_clk_name[i] = kasprintf(GFP_KERNEL, "%pOFn.pll%d",
 			client->dev.of_node, i);
+		if (!pll_clk_name[i]) {
+			err = -ENOMEM;
+			goto error;
+		}
 		init.name = pll_clk_name[i];
 		data->pll[i].chip = data;
 		data->pll[i].hw.init = &init;
@@ -746,6 +750,10 @@
 	init.num_parents = 1;
 	init.parent_names = &parent_name; /* Mux Y1 to input */
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.Y1", client->dev.of_node);
+	if (!init.name) {
+		err = -ENOMEM;
+		goto error;
+	}
 	data->clk[0].chip = data;
 	data->clk[0].hw.init = &init;
 	data->clk[0].index = 0;
@@ -764,6 +772,10 @@
 	for (i = 1; i < data->chip_info->num_outputs; ++i) {
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.Y%d",
 			client->dev.of_node, i+1);
+		if (!init.name) {
+			err = -ENOMEM;
+			goto error;
+		}
 		data->clk[i].chip = data;
 		data->clk[i].hw.init = &init;
 		data->clk[i].index = i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-clps711x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-clps711x.c
@@ -28,11 +28,13 @@
 	{ .val = 1, .div = 8, },
 	{ .val = 2, .div = 2, },
 	{ .val = 3, .div = 1, },
+	{ /* sentinel */ }
 };
 
 static const struct clk_div_table timer_div_table[] = {
 	{ .val = 0, .div = 256, },
 	{ .val = 1, .div = 1, },
+	{ /* sentinel */ }
 };
 
 struct clps711x_clk {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-conf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-conf.c
@@ -33,9 +33,12 @@
 			else
 				return rc;
 		}
-		if (clkspec.np == node && !clk_supplier)
+		if (clkspec.np == node && !clk_supplier) {
+			of_node_put(clkspec.np);
 			return 0;
+		}
 		pclk = of_clk_get_from_provider(&clkspec);
+		of_node_put(clkspec.np);
 		if (IS_ERR(pclk)) {
 			if (PTR_ERR(pclk) != -EPROBE_DEFER)
 				pr_warn("clk: couldn't get parent clock %d for %pOF\n",
@@ -48,10 +51,12 @@
 		if (rc < 0)
 			goto err;
 		if (clkspec.np == node && !clk_supplier) {
+			of_node_put(clkspec.np);
 			rc = 0;
 			goto err;
 		}
 		clk = of_clk_get_from_provider(&clkspec);
+		of_node_put(clkspec.np);
 		if (IS_ERR(clk)) {
 			if (PTR_ERR(clk) != -EPROBE_DEFER)
 				pr_warn("clk: couldn't get assigned clock %d for %pOF\n",
@@ -93,10 +98,13 @@
 				else
 					return rc;
 			}
-			if (clkspec.np == node && !clk_supplier)
+			if (clkspec.np == node && !clk_supplier) {
+				of_node_put(clkspec.np);
 				return 0;
+			}
 
 			clk = of_clk_get_from_provider(&clkspec);
+			of_node_put(clkspec.np);
 			if (IS_ERR(clk)) {
 				if (PTR_ERR(clk) != -EPROBE_DEFER)
 					pr_warn("clk: couldn't get clock %d for %pOF\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-devres.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-devres.c
@@ -4,42 +4,101 @@
 #include <linux/export.h>
 #include <linux/gfp.h>
 
+struct devm_clk_state {
+	struct clk *clk;
+	void (*exit)(struct clk *clk);
+};
+
 static void devm_clk_release(struct device *dev, void *res)
 {
-	clk_put(*(struct clk **)res);
+	struct devm_clk_state *state = res;
+
+	if (state->exit)
+		state->exit(state->clk);
+
+	clk_put(state->clk);
 }
 
-struct clk *devm_clk_get(struct device *dev, const char *id)
+static struct clk *__devm_clk_get(struct device *dev, const char *id,
+				  struct clk *(*get)(struct device *dev, const char *id),
+				  int (*init)(struct clk *clk),
+				  void (*exit)(struct clk *clk))
 {
-	struct clk **ptr, *clk;
+	struct devm_clk_state *state;
+	struct clk *clk;
+	int ret;
 
-	ptr = devres_alloc(devm_clk_release, sizeof(*ptr), GFP_KERNEL);
-	if (!ptr)
+	state = devres_alloc(devm_clk_release, sizeof(*state), GFP_KERNEL);
+	if (!state)
 		return ERR_PTR(-ENOMEM);
 
-	clk = clk_get(dev, id);
-	if (!IS_ERR(clk)) {
-		*ptr = clk;
-		devres_add(dev, ptr);
-	} else {
-		devres_free(ptr);
+	clk = get(dev, id);
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		goto err_clk_get;
 	}
 
+	if (init) {
+		ret = init(clk);
+		if (ret)
+			goto err_clk_init;
+	}
+
+	state->clk = clk;
+	state->exit = exit;
+
+	devres_add(dev, state);
+
 	return clk;
+
+err_clk_init:
+
+	clk_put(clk);
+err_clk_get:
+
+	devres_free(state);
+	return ERR_PTR(ret);
+}
+
+struct clk *devm_clk_get(struct device *dev, const char *id)
+{
+	return __devm_clk_get(dev, id, clk_get, NULL, NULL);
 }
 EXPORT_SYMBOL(devm_clk_get);
 
-struct clk *devm_clk_get_optional(struct device *dev, const char *id)
+struct clk *devm_clk_get_prepared(struct device *dev, const char *id)
 {
-	struct clk *clk = devm_clk_get(dev, id);
+	return __devm_clk_get(dev, id, clk_get, clk_prepare, clk_unprepare);
+}
+EXPORT_SYMBOL_GPL(devm_clk_get_prepared);
 
-	if (clk == ERR_PTR(-ENOENT))
-		return NULL;
+struct clk *devm_clk_get_enabled(struct device *dev, const char *id)
+{
+	return __devm_clk_get(dev, id, clk_get,
+			      clk_prepare_enable, clk_disable_unprepare);
+}
+EXPORT_SYMBOL_GPL(devm_clk_get_enabled);
 
-	return clk;
+struct clk *devm_clk_get_optional(struct device *dev, const char *id)
+{
+	return __devm_clk_get(dev, id, clk_get_optional, NULL, NULL);
 }
 EXPORT_SYMBOL(devm_clk_get_optional);
 
+struct clk *devm_clk_get_optional_prepared(struct device *dev, const char *id)
+{
+	return __devm_clk_get(dev, id, clk_get_optional,
+			      clk_prepare, clk_unprepare);
+}
+EXPORT_SYMBOL_GPL(devm_clk_get_optional_prepared);
+
+struct clk *devm_clk_get_optional_enabled(struct device *dev, const char *id)
+{
+	return __devm_clk_get(dev, id, clk_get_optional,
+			      clk_prepare_enable, clk_disable_unprepare);
+}
+EXPORT_SYMBOL_GPL(devm_clk_get_optional_enabled);
+
 struct clk_bulk_devres {
 	struct clk_bulk_data *clks;
 	int num_clks;
@@ -146,18 +205,19 @@
 struct clk *devm_get_clk_from_child(struct device *dev,
 				    struct device_node *np, const char *con_id)
 {
-	struct clk **ptr, *clk;
+	struct devm_clk_state *state;
+	struct clk *clk;
 
-	ptr = devres_alloc(devm_clk_release, sizeof(*ptr), GFP_KERNEL);
-	if (!ptr)
+	state = devres_alloc(devm_clk_release, sizeof(*state), GFP_KERNEL);
+	if (!state)
 		return ERR_PTR(-ENOMEM);
 
 	clk = of_clk_get_by_name(np, con_id);
 	if (!IS_ERR(clk)) {
-		*ptr = clk;
-		devres_add(dev, ptr);
+		state->clk = clk;
+		devres_add(dev, state);
 	} else {
-		devres_free(ptr);
+		devres_free(state);
 	}
 
 	return clk;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-fixed-rate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-fixed-rate.c
@@ -49,12 +49,24 @@
 };
 EXPORT_SYMBOL_GPL(clk_fixed_rate_ops);
 
+static void devm_clk_hw_register_fixed_rate_release(struct device *dev, void *res)
+{
+	struct clk_fixed_rate *fix = res;
+
+	/*
+	 * We can not use clk_hw_unregister_fixed_rate, since it will kfree()
+	 * the hw, resulting in double free. Just unregister the hw and let
+	 * devres code kfree() it.
+	 */
+	clk_hw_unregister(&fix->hw);
+}
+
 struct clk_hw *__clk_hw_register_fixed_rate(struct device *dev,
 		struct device_node *np, const char *name,
 		const char *parent_name, const struct clk_hw *parent_hw,
 		const struct clk_parent_data *parent_data, unsigned long flags,
 		unsigned long fixed_rate, unsigned long fixed_accuracy,
-		unsigned long clk_fixed_flags)
+		unsigned long clk_fixed_flags, bool devm)
 {
 	struct clk_fixed_rate *fixed;
 	struct clk_hw *hw;
@@ -62,7 +74,11 @@
 	int ret = -EINVAL;
 
 	/* allocate fixed-rate clock */
-	fixed = kzalloc(sizeof(*fixed), GFP_KERNEL);
+	if (devm)
+		fixed = devres_alloc(devm_clk_hw_register_fixed_rate_release,
+				     sizeof(*fixed), GFP_KERNEL);
+	else
+		fixed = kzalloc(sizeof(*fixed), GFP_KERNEL);
 	if (!fixed)
 		return ERR_PTR(-ENOMEM);
 
@@ -90,9 +106,13 @@
 	else if (np)
 		ret = of_clk_hw_register(np, hw);
 	if (ret) {
-		kfree(fixed);
+		if (devm)
+			devres_free(fixed);
+		else
+			kfree(fixed);
 		hw = ERR_PTR(ret);
-	}
+	} else if (devm)
+		devres_add(dev, fixed);
 
 	return hw;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-npcm7xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-npcm7xx.c
@@ -539,7 +539,7 @@
 	return;
 
 npcm7xx_init_fail:
-	kfree(npcm7xx_clk_data->hws);
+	kfree(npcm7xx_clk_data);
 npcm7xx_init_np_err:
 	iounmap(clk_base);
 npcm7xx_init_error:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-oxnas.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-oxnas.c
@@ -207,7 +207,7 @@
 
 static int oxnas_stdclk_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
+	struct device_node *np = pdev->dev.of_node, *parent_np;
 	const struct oxnas_stdclk_data *data;
 	const struct of_device_id *id;
 	struct regmap *regmap;
@@ -219,7 +219,9 @@
 		return -ENODEV;
 	data = id->data;
 
-	regmap = syscon_node_to_regmap(of_get_parent(np));
+	parent_np = of_get_parent(np);
+	regmap = syscon_node_to_regmap(parent_np);
+	of_node_put(parent_np);
 	if (IS_ERR(regmap)) {
 		dev_err(&pdev->dev, "failed to have parent regmap\n");
 		return PTR_ERR(regmap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-qoriq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-qoriq.c
@@ -1063,8 +1063,13 @@
  */
 static void __init legacy_init_clockgen(struct device_node *np)
 {
-	if (!clockgen.node)
-		_clockgen_init(of_get_parent(np), true);
+	if (!clockgen.node) {
+		struct device_node *parent_np;
+
+		parent_np = of_get_parent(np);
+		_clockgen_init(parent_np, true);
+		of_node_put(parent_np);
+	}
 }
 
 /* Legacy node */
@@ -1159,6 +1164,7 @@
 	sysclk = of_get_child_by_name(clockgen.node, "sysclk");
 	if (sysclk) {
 		clk = sysclk_from_fixed(sysclk, name);
+		of_node_put(sysclk);
 		if (!IS_ERR(clk))
 			return clk;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-scmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-scmi.c
@@ -178,6 +178,7 @@
 		sclk->info = scmi_proto_clk_ops->info_get(ph, idx);
 		if (!sclk->info) {
 			dev_dbg(dev, "invalid clock info for idx %d\n", idx);
+			devm_kfree(dev, sclk);
 			continue;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-si5324.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-si5324.c
@@ -0,0 +1,1227 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * clk-si5324.c - Si5324 clock driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author:	Venkateshwar Rao G <vgannava.xilinx.com>
+ *		Leon Woestenberg <leon@sidebranch.com>
+ */
+
+#include <asm/div64.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/rational.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+
+#include "clk-si5324.h"
+#include "si5324.h"
+#include "si5324drv.h"
+
+struct si5324_driver_data;
+
+/**
+ * struct si5324_parameters - si5324 core parameters
+ *
+ * @n1_hs_min:		Minimum high-speed n1 output divider
+ * @n1_hs_max:		Maximum high-speed n1 output divider
+ * @n1_hs:		n1 high-speed output divider
+ * @nc1_ls_min:		Minimum low-speed clkout1 output divider
+ * @nc1_ls_max:		Maximum low-speed clkout1 output divider
+ * @nc1_ls:		Clkout1 low-speed output divider
+ * @nc2_ls_min:		Minimum low-speed clkout2 output divider
+ * @nc2_ls_max:		Maximum low-speed clkout2 output divider
+ * @nc2_ls:		Clkout2 low-speed output divider
+ * @n2_hs:		High-speed feedback divider
+ * @n2_ls_min:		Minimum low-speed feedback divider
+ * @n2_ls_max:		Maximum low-speed feedback divider
+ * @n2_ls:		Low-speed feedback divider
+ * @n31_min:		Minimum input divider for clk1
+ * @n31_max:		Maximum input divider for clk1
+ * @n31:		Input divider for clk1
+ * @n32_min:		Minimum input divider for clk2
+ * @n32_max:		Maximum input divider for clk2
+ * @n32:		Input divider for clk2
+ * @fin:		Input frequency
+ * @fout:		Output frequency
+ * @fosc:		Osc frequency
+ * @best_delta_fout:	Delta out frequency
+ * @best_fout:		Best output frequency
+ * @best_n1_hs:		Best high speed output divider
+ * @best_nc1_ls:	Best low speed clkout1 divider
+ * @best_n2_hs:		Best high speed feedback divider
+ * @best_n2_ls:		Best low speed feedback divider
+ * @best_n3:		Best input clock divider
+ * @valid: Validility
+ */
+struct si5324_parameters {
+	u32 n1_hs_min;
+	u32 n1_hs_max;
+	u32 n1_hs;
+	u32 nc1_ls_min;
+	u32 nc1_ls_max;
+	u32 nc1_ls;
+	u32 nc2_ls_min;
+	u32 nc2_ls_max;
+	u32 nc2_ls;
+	u32 n2_hs;
+	u32 n2_ls_min;
+	u32 n2_ls_max;
+	u32 n2_ls;
+	u32 n31_min;
+	u32 n31_max;
+	u32 n31;
+	u32 n32_min;
+	u32 n32_max;
+	u32 n32;
+	u64 fin;
+	u64 fout;
+	u64 fosc;
+	u64 best_delta_fout;
+	u64 best_fout;
+	u32 best_n1_hs;
+	u32 best_nc1_ls;
+	u32 best_n2_hs;
+	u32 best_n2_ls;
+	u32 best_n3;
+	int valid;
+};
+
+/**
+ * struct si5324_hw_data - Clock parameters
+ *
+ * @hw:		Handle between common and hardware-specific interfaces
+ * @drvdata:	Driver private data
+ * @num:	Differential pair clock number
+ */
+struct si5324_hw_data {
+	struct clk_hw hw;
+	struct si5324_driver_data *drvdata;
+	unsigned char num;
+};
+
+/**
+ * struct si5324_driver_data - Driver parameters
+ * @client:		I2C client pointer
+ * @regmap:		Device's regmap
+ * @onecell:		Clock onecell data
+ * @params:		Device parameters
+ * @pxtal:		Clock
+ * @pxtal_name:		Clock name
+ * @xtal:		Reference clock
+ * @pclkin1:		Clock in 1
+ * @pclkin1_name:	Clock in 1 name
+ * @clkin1:		Differential input clock 1
+ * @pclkin2:		Clock in 2
+ * @pclkin2_name:	Clock in 2 name
+ * @clkin2:		Differential input clock 2
+ * @pll:		Pll clock
+ * @clkout:		Output clock
+ * @rate_clkout0:	Clock out 0 rate
+ * @rate_clkout1:	Clock out 1 rate
+ */
+struct si5324_driver_data {
+	struct i2c_client		*client;
+	struct regmap			*regmap;
+	struct clk_onecell_data		onecell;
+	struct si5324_parameters	params;
+	struct clk			*pxtal;
+	const char			*pxtal_name;
+	struct clk_hw			xtal;
+	struct clk			*pclkin1;
+	const char			*pclkin1_name;
+	struct clk_hw			clkin1;
+	struct clk			*pclkin2;
+	const char			*pclkin2_name;
+	struct clk_hw			clkin2;
+	struct si5324_hw_data		pll;
+	struct si5324_hw_data		*clkout;
+	unsigned long			rate_clkout0;
+	unsigned long			rate_clkout1;
+};
+
+static const char * const si5324_input_names[] = {
+	"xtal", "clkin1", "clkin2"
+};
+
+static const char * const si5324_pll_name = "pll";
+
+static const char * const si5324_clkout_names[] = {
+	"clk0", "clk1"
+};
+
+enum si53xx_variant {
+	si5319,
+	si5324,
+	si5328
+};
+
+static const char * const si53xx_variant_name[] = {
+	"si5319", "si5324", "si5328"
+};
+
+/**
+ * si5324_reg_read - Read a single si5324 register.
+ *
+ * @drvdata:	Device to read from.
+ * @reg:	Register to read.
+ *
+ * This function reads data from a single register
+ *
+ * Return:	Data of the register on success, error number on failure
+ */
+static inline int
+si5324_reg_read(struct si5324_driver_data *drvdata, u8 reg)
+{
+	u32 val;
+	int ret;
+
+	ret = regmap_read(drvdata->regmap, reg, &val);
+	if (ret < 0) {
+		dev_err(&drvdata->client->dev,
+			"unable to read from reg%02x\n", reg);
+		return ret;
+	}
+
+	return (u8)val;
+}
+
+/**
+ * si5324_bulk_read - Read multiple si5324 registers
+ *
+ * @drvdata:	Device to read from
+ * @reg:	First register to be read from
+ * @count:	Number of registers
+ * @buf:	Pointer to store read value
+ *
+ * This function reads from multiple registers which are in
+ * sequential order
+ *
+ * Return:	Number of bytes read
+ */
+static inline int si5324_bulk_read(struct si5324_driver_data *drvdata,
+				   u8 reg, u8 count, u8 *buf)
+{
+	return regmap_bulk_read(drvdata->regmap, reg, buf, count);
+}
+
+/**
+ * si5324_reg_write - Write a single si5324 register.
+ *
+ * @drvdata:	Device to write to.
+ * @reg:	Register to write to.
+ * @val:	Value to write.
+ *
+ * This function writes into a single register
+ *
+ * Return:	Zero on success, a negative error number on failure.
+ *
+ */
+static inline int si5324_reg_write(struct si5324_driver_data *drvdata,
+				   u8 reg, u8 val)
+{
+	int ret = regmap_write(drvdata->regmap, reg, val);
+
+	dev_dbg(&drvdata->client->dev, "%s 0x%02x @%02d\n", __func__,
+		(int)val, (int)reg);
+	return ret;
+}
+
+/**
+ * si5324_bulk_write - Write into multiple si5324 registers
+ *
+ * @drvdata:	Device to write to
+ * @reg:	First register
+ * @count:	Number of registers
+ * @buf:	Block of data to be written
+ *
+ * This function writes into multiple registers.
+ *
+ * Return:	Zero on success, a negative error number on failure.
+ */
+static inline int si5324_bulk_write(struct si5324_driver_data *drvdata,
+				    u8 reg, u8 count, const u8 *buf)
+{
+	return regmap_raw_write(drvdata->regmap, reg, buf, count);
+}
+
+/**
+ * si5324_set_bits - Set the value of a bitfield in a si5324 register
+ *
+ * @drvdata:	Device to write to.
+ * @reg:	Register to write to.
+ * @mask:	Mask of bits to set.
+ * @val:	Value to set (unshifted)
+ *
+ * This function set particular bits in register
+ *
+ * Return:	Zero on success, a negative error number on failure.
+ */
+static inline int si5324_set_bits(struct si5324_driver_data *drvdata,
+				  u8 reg, u8 mask, u8 val)
+{
+	return regmap_update_bits(drvdata->regmap, reg, mask, val);
+}
+
+/**
+ * si5324_bulk_scatter_write - Write into multiple si5324 registers
+ *
+ * @drvdata:	Device to write to
+ * @count:	Number of registers
+ * @buf:	Register and data to write
+ *
+ * This function writes into multiple registers which are need not
+ * to be in sequential order.
+ *
+ * Return:	Number of bytes written
+ */
+static inline int
+si5324_bulk_scatter_write(struct si5324_driver_data *drvdata,
+			  u8 count, const u8 *buf)
+{
+	int i;
+	int ret = 0;
+
+	for (i = 0; i < count; i++) {
+		ret = si5324_reg_write(drvdata, buf[i * 2], buf[i * 2 + 1]);
+		if (ret)
+			return ret;
+	}
+	return ret;
+}
+
+/**
+ * si5324_initialize - Initializes si5324 device
+ *
+ * @drvdata:	Device instance
+ *
+ * This function initializes si5324 with the following settings
+ * Keep reset asserted for 20ms
+ * 1. freerun mode
+ * 2. Disable output clocks during calibration
+ * 3. Clock selection mode : default value, manual
+ * 4. output signal format : LVDS for clkout1, disable clkout2
+ * 5. CS_CA pin in ignored
+ * 6. Set lock time to 13.3ms
+ * 7. Enables the fastlock.
+ *
+ * Return:	Zero on success, negative number on failure.
+ */
+static int si5324_initialize(struct si5324_driver_data *drvdata)
+{
+	int ret = 0;
+
+	si5324_set_bits(drvdata, SI5324_RESET_CALIB,
+			SI5324_RST_ALL, SI5324_RST_ALL);
+	msleep(SI5324_RESET_DELAY_MS);
+	si5324_set_bits(drvdata, SI5324_RESET_CALIB, SI5324_RST_ALL, 0);
+	msleep(SI5324_RESET_DELAY_MS);
+
+	ret = si5324_reg_read(drvdata, SI5324_CONTROL);
+	if (ret < 0)
+		return ret;
+
+	si5324_reg_write(drvdata, SI5324_CONTROL,
+			 (ret | SI5324_CONTROL_FREE_RUN));
+
+	ret = si5324_reg_read(drvdata, SI5324_CKSEL);
+	if (ret < 0)
+		return ret;
+
+	si5324_reg_write(drvdata, SI5324_CKSEL, (ret | SI5324_CKSEL_SQL_ICAL));
+	si5324_reg_write(drvdata, SI3324_AUTOSEL, SI5324_AUTOSEL_DEF);
+	si5324_reg_write(drvdata, SI5324_OUTPUT_SIGFMT,
+			 SI5324_OUTPUT_SF1_DEFAULT);
+
+	ret = si5324_reg_read(drvdata, SI5324_DSBL_CLKOUT);
+	if (ret < 0)
+		return ret;
+
+	si5324_reg_write(drvdata, SI5324_DSBL_CLKOUT,
+			 (ret | SI5324_DSBL_CLKOUT2));
+	ret = si5324_reg_read(drvdata, SI5324_POWERDOWN);
+	if (ret < 0)
+		return ret;
+
+	si5324_reg_write(drvdata, SI5324_POWERDOWN, (ret | SI5324_PD_CK2));
+	si5324_reg_write(drvdata, SI5324_FOS_LOCKT, SI5324_FOS_DEFAULT);
+
+	ret = si5324_reg_read(drvdata, SI5324_CK_ACTV_SEL);
+	if (ret < 0)
+		return ret;
+
+	si5324_reg_write(drvdata, SI5324_CK_ACTV_SEL, SI5324_CK_DEFAULT);
+	ret = si5324_reg_read(drvdata, SI5324_FASTLOCK);
+	if (ret < 0)
+		return ret;
+
+	si5324_reg_write(drvdata, SI5324_FASTLOCK, (ret | SI5324_FASTLOCK_EN));
+	return 0;
+}
+
+/**
+ * si5324_read_parameters - Reads clock divider parameters
+ *
+ * @drvdata:	Device to read from
+ *
+ * This function reads the clock divider parameters into driver structure.
+ *
+ * Following table gives the buffer index, register number and
+ * register name with bit fields
+ * 0 25 N1_HS[2:0]
+ * 6 31 NC1_LS[19:16]
+ * 7 32 NC1_LS[15:8]
+ * 8 33 NC1_LS[7:0]
+ * 9 34 NC2_LS[19:16]
+ * 10 35 NC2_LS[15:8]
+ * 11 36 NC2_LS[7:0]
+ * 15 40 N2_HS[2:0] N2_LS[19:16]
+ * 16 41 N2_LS[15:8]
+ * 17 42 N2_LS[7:0]
+ * 18 43 N31[18:16]
+ * 19 44 N31[15:8]
+ * 20 45 N31[7:0]
+ * 21 46 N32[18:16]
+ * 22 47 N32[15:8]
+ * 23 48 N32[7:0]
+ */
+static void si5324_read_parameters(struct si5324_driver_data *drvdata)
+{
+	u8 buf[SI5324_PARAM_LEN];
+
+	si5324_bulk_read(drvdata, SI5324_N1_HS, SI5324_N1_PARAM_LEN, &buf[0]);
+	si5324_bulk_read(drvdata, SI5324_NC1_LS_H, SI5324_NC_PARAM_LEN,
+			 &buf[6]);
+	si5324_bulk_read(drvdata, SI5324_N2_HS_LS_H, SI5324_N2_PARAM_LEN,
+			 &buf[15]);
+
+	drvdata->params.n1_hs = (buf[0] >> SI5324_N1_HS_VAL_SHIFT);
+	drvdata->params.n1_hs += 4;
+
+	drvdata->params.nc1_ls = ((buf[6] & SI5324_DIV_LS_MASK) <<
+				  SI5324_HSHIFT) | (buf[7] << SI5324_LSHIFT) |
+				  buf[8];
+	drvdata->params.nc1_ls += 1;
+	drvdata->params.nc2_ls = ((buf[9] & SI5324_DIV_LS_MASK) <<
+				  SI5324_HSHIFT) | (buf[10] << SI5324_LSHIFT) |
+				  buf[11];
+	drvdata->params.nc2_ls += 1;
+	drvdata->params.n2_ls = ((buf[15] & SI5324_DIV_LS_MASK) <<
+				 SI5324_HSHIFT) | (buf[16] << SI5324_LSHIFT) |
+				 buf[17];
+	drvdata->params.n2_ls += 1;
+	drvdata->params.n2_hs = buf[15] >> SI5324_N2_HS_LS_H_VAL_SHIFT;
+	drvdata->params.n2_hs += 4;
+	drvdata->params.n31 = ((buf[18] & SI5324_DIV_LS_MASK) <<
+				SI5324_HSHIFT) | (buf[19] << SI5324_LSHIFT) |
+				buf[20];
+	drvdata->params.n31 += 1;
+	drvdata->params.n32 = ((buf[21] & SI5324_DIV_LS_MASK) <<
+				SI5324_HSHIFT) | (buf[22] << SI5324_LSHIFT) |
+				buf[23];
+	drvdata->params.n32 += 1;
+	drvdata->params.valid = 1;
+}
+
+static bool si5324_regmap_is_volatile(struct device *dev, unsigned int reg)
+{
+	return true;
+}
+
+/**
+ * si5324_regmap_is_readable - Checks the register is readable or not
+ *
+ * @dev:	Registered device
+ * @reg:	Register offset
+ *
+ * Checks the register is readable or not.
+ *
+ * Return:	True if the register is reabdle, False if it is not readable.
+ */
+static bool si5324_regmap_is_readable(struct device *dev, unsigned int reg)
+{
+	if ((reg > SI5324_POWERDOWN && reg < SI5324_FOS_LOCKT) ||
+	    (reg > SI5324_N1_HS && reg < SI5324_NC1_LS_H) ||
+	    (reg > SI5324_NC2_LS_L && reg < SI5324_N2_HS_LS_H) ||
+	    (reg > SI5324_N32_CLKIN_L && reg < SI5324_FOS_CLKIN_RATE) ||
+	    (reg > SI5324_FOS_CLKIN_RATE && reg < SI5324_PLL_ACTV_CLK) ||
+	    reg > SI5324_SKEW2)
+		return false;
+
+	return true;
+}
+
+/**
+ * si5324_regmap_is_writable - Checks the register is writable or not
+ *
+ * @dev:	Registered device
+ * @reg:	Register offset
+ *
+ * Checks the register is writable or not.
+ *
+ * Return:	True if the register is writeable, False if it's not writeable.
+ */
+static bool si5324_regmap_is_writeable(struct device *dev, unsigned int reg)
+{
+	if ((reg > SI5324_POWERDOWN && reg < SI5324_FOS_LOCKT) ||
+	    (reg > SI5324_N1_HS && reg < SI5324_NC1_LS_H) ||
+	    (reg > SI5324_NC2_LS_L && reg < SI5324_N2_HS_LS_H) ||
+	    (reg > SI5324_N32_CLKIN_L && reg < SI5324_FOS_CLKIN_RATE) ||
+	    (reg > SI5324_FOS_CLKIN_RATE && reg < SI5324_PLL_ACTV_CLK) ||
+	    reg > SI5324_SKEW2 ||
+	    (reg >= SI5324_PLL_ACTV_CLK && reg <= SI5324_CLKIN_LOL_STATUS) ||
+	    (reg >= SI5324_PARTNO_H && reg <= SI5324_PARTNO_L))
+		return false;
+
+	return true;
+}
+
+static const struct regmap_config si5324_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = 144,
+	.writeable_reg = si5324_regmap_is_writeable,
+	.readable_reg = si5324_regmap_is_readable,
+	.volatile_reg = si5324_regmap_is_volatile,
+};
+
+static int si5324_xtal_prepare(struct clk_hw *hw)
+{
+	return 0;
+}
+
+static void si5324_xtal_unprepare(struct clk_hw *hw)
+{
+}
+
+static const struct clk_ops si5324_xtal_ops = {
+	.prepare = si5324_xtal_prepare,
+	.unprepare = si5324_xtal_unprepare,
+};
+
+/**
+ * si5324_clkin_prepare - Prepare the clkin
+ *
+ * @hw:		Handle between common and hardware-specific interfaces
+ *
+ * This function enables the particular clk
+ *
+ * Return:	Zero on success, a negative error number on failure.
+ */
+static int si5324_clkin_prepare(struct clk_hw *hw)
+{
+	int ret = 0;
+	struct si5324_driver_data *drvdata;
+	struct si5324_hw_data *hwdata =
+		container_of(hw, struct si5324_hw_data, hw);
+
+	if (hwdata->num == SI5324_CLKIN1) {
+		drvdata = container_of(hw, struct si5324_driver_data, clkin1);
+		ret = si5324_set_bits(drvdata, SI5324_CONTROL,
+				      SI5324_CONTROL_FREE_RUN, 0);
+		ret = si5324_set_bits(drvdata, SI5324_POWERDOWN, SI5324_PD_CK1 |
+				      SI5324_PD_CK2, SI5324_PD_CK2);
+	} else if (hwdata->num == SI5324_CLKIN2) {
+		drvdata = container_of(hw, struct si5324_driver_data, clkin2);
+		ret = si5324_set_bits(drvdata, SI5324_CONTROL,
+				      SI5324_CONTROL_FREE_RUN, 0);
+		ret = si5324_set_bits(drvdata, SI5324_POWERDOWN, SI5324_PD_CK1 |
+				      SI5324_PD_CK2, SI5324_PD_CK1);
+	}
+
+	return ret;
+}
+
+/**
+ * si5324_clkin_unprepare - Unprepare the clkin
+ *
+ * @hw:		Clock hardware
+ *
+ * This function enables the particular clk.
+ */
+static void si5324_clkin_unprepare(struct clk_hw *hw)
+{
+	struct si5324_driver_data *drvdata;
+	struct si5324_hw_data *hwdata =
+		container_of(hw, struct si5324_hw_data, hw);
+
+	if (hwdata->num == SI5324_CLKIN1) {
+		drvdata = container_of(hw, struct si5324_driver_data, clkin1);
+		si5324_set_bits(drvdata, SI5324_POWERDOWN,
+				SI5324_PD_CK1 | SI5324_PD_CK2, SI5324_PD_CK1);
+	} else if (hwdata->num == SI5324_CLKIN2) {
+		drvdata = container_of(hw, struct si5324_driver_data, clkin2);
+		si5324_set_bits(drvdata, SI5324_POWERDOWN,
+				SI5324_PD_CK1 | SI5324_PD_CK2, SI5324_PD_CK1);
+	}
+}
+
+static unsigned long si5324_clkin_recalc_rate(struct clk_hw *hw,
+					      unsigned long parent_rate)
+{
+	return 0;
+}
+
+static const struct clk_ops si5324_clkin_ops = {
+	.prepare = si5324_clkin_prepare,
+	.unprepare = si5324_clkin_unprepare,
+	.recalc_rate = si5324_clkin_recalc_rate,
+};
+
+static int si5324_pll_reparent(struct si5324_driver_data *drvdata,
+			       int num, enum si5324_pll_src parent)
+{
+	if (parent == SI5324_PLL_SRC_XTAL) {
+		si5324_set_bits(drvdata, SI5324_CONTROL,
+				SI5324_CONTROL_FREE_RUN,
+				SI5324_CONTROL_FREE_RUN);
+		si5324_set_bits(drvdata, SI5324_POWERDOWN,
+				SI5324_PD_CK1 | SI5324_PD_CK2, SI5324_PD_CK1);
+		si5324_set_bits(drvdata, SI5324_CKSEL,
+				SI5324_CK_SEL << SI5324_CKSEL_SHIFT,
+				1 << SI5324_CKSEL_SHIFT);
+	} else if (parent == SI5324_PLL_SRC_CLKIN1) {
+		si5324_set_bits(drvdata, SI5324_CONTROL,
+				SI5324_CONTROL_FREE_RUN, 0);
+		si5324_set_bits(drvdata, SI5324_POWERDOWN,
+				SI5324_PD_CK1 | SI5324_PD_CK2, SI5324_PD_CK2);
+		si5324_set_bits(drvdata, SI5324_CKSEL,
+				SI5324_CK_SEL << SI5324_CKSEL_SHIFT, 0);
+	} else if (parent == SI5324_PLL_SRC_CLKIN2) {
+		si5324_set_bits(drvdata, SI5324_CONTROL,
+				SI5324_CONTROL_FREE_RUN, 0);
+		si5324_set_bits(drvdata, SI5324_POWERDOWN,
+				SI5324_PD_CK1 | SI5324_PD_CK2, SI5324_PD_CK1);
+		si5324_set_bits(drvdata, SI5324_CKSEL,
+				SI5324_CK_SEL << SI5324_CKSEL_SHIFT,
+				1 << SI5324_CKSEL_SHIFT);
+	}
+
+	return 0;
+}
+
+static unsigned char si5324_pll_get_parent(struct clk_hw *hw)
+{
+	return 0;
+}
+
+/**
+ * si5324_pll_set_parent - Set parent of clock
+ *
+ * @hw:		Handle between common and hardware-specific interfaces
+ * @index:	Parent index
+ *
+ * This function sets the paraent of clock.
+ *
+ * Return:	0 on success, negative error number on failure
+ */
+static int si5324_pll_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct si5324_hw_data *hwdata =
+		container_of(hw, struct si5324_hw_data, hw);
+	enum si5324_pll_src parent;
+
+	if (index == SI5324_SRC_XTAL)
+		parent = SI5324_PLL_SRC_XTAL;
+	else if (index == SI5324_SRC_CLKIN1)
+		parent = SI5324_PLL_SRC_CLKIN1;
+	else if (index == SI5324_SRC_CLKIN2)
+		parent = SI5324_PLL_SRC_CLKIN2;
+	else
+		return -EINVAL;
+
+	return si5324_pll_reparent(hwdata->drvdata, hwdata->num, parent);
+}
+
+/**
+ * si5324_pll_recalc_rate - Recalculate clock frequency
+ *
+ * @hw:			Handle between common and hardware-specific interfaces
+ * @parent_rate:	Clock frequency of parent clock
+ *
+ * This function recalculate clock frequency.
+ *
+ * Return:		Current clock frequency
+ */
+static unsigned long si5324_pll_recalc_rate(struct clk_hw *hw,
+					    unsigned long parent_rate)
+{
+	unsigned long rate;
+	struct si5324_hw_data *hwdata =
+		container_of(hw, struct si5324_hw_data, hw);
+
+	if (!hwdata->drvdata->params.valid)
+		si5324_read_parameters(hwdata->drvdata);
+	WARN_ON(!hwdata->drvdata->params.valid);
+
+	rate = parent_rate * hwdata->drvdata->params.n2_ls *
+		hwdata->drvdata->params.n2_hs;
+
+	dev_dbg(&hwdata->drvdata->client->dev,
+		"%s - %s: n2_ls = %u, n2_hs = %u, parent_rate = %lu, rate = %lu\n",
+		__func__, clk_hw_get_name(hw),
+		hwdata->drvdata->params.n2_ls, hwdata->drvdata->params.n2_hs,
+		parent_rate, (unsigned long)rate);
+
+	return rate;
+}
+
+static long si5324_pll_round_rate(struct clk_hw *hw, unsigned long rate,
+				  unsigned long *parent_rate)
+{
+	return rate;
+}
+
+static int si5324_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+			       unsigned long parent_rate)
+{
+	return 0;
+}
+
+static const struct clk_ops si5324_pll_ops = {
+	.set_parent = si5324_pll_set_parent,
+	.get_parent = si5324_pll_get_parent,
+	.recalc_rate = si5324_pll_recalc_rate,
+	.round_rate = si5324_pll_round_rate,
+	.set_rate = si5324_pll_set_rate,
+};
+
+static int si5324_clkout_set_drive_strength(
+	struct si5324_driver_data *drvdata, int num,
+	enum si5324_drive_strength drive)
+{
+	return 0;
+}
+
+static int si5324_clkout_prepare(struct clk_hw *hw)
+{
+	return 0;
+}
+
+static void si5324_clkout_unprepare(struct clk_hw *hw)
+{
+}
+
+static unsigned long si5324_clkout_recalc_rate(struct clk_hw *hw,
+					       unsigned long parent_rate)
+{
+	unsigned long rate;
+
+	struct si5324_hw_data *hwdata =
+		container_of(hw, struct si5324_hw_data, hw);
+
+	rate = hwdata->drvdata->rate_clkout0;
+
+	return rate;
+}
+
+/**
+ * si5324_clkout_round_rate - selects the closest value to requested one.
+ *
+ * @hw:			Handle between common and hardware-specific interfaces
+ * @rate:		Clock rate
+ * @parent_rate:	Parent clock rate
+ *
+ * This function selects the rate closest to the requested one.
+ *
+ * Return:		Clock rate on success, negative error number on failure
+ */
+static long si5324_clkout_round_rate(struct clk_hw *hw, unsigned long rate,
+				     unsigned long *parent_rate)
+{
+	u32 ncn_ls, n2_ls, n3n, actual_rate;
+	u8 n1_hs, n2_hs, bwsel;
+	int ret;
+
+	ret = si5324_calcfreqsettings(SI5324_REF_CLOCK, rate, &actual_rate,
+				      &n1_hs, &ncn_ls, &n2_hs, &n2_ls, &n3n,
+				      &bwsel);
+	if (ret < 0)
+		return ret;
+
+	return actual_rate;
+}
+
+static int si5324_clkout_set_rate(struct clk_hw *hw, unsigned long rate,
+				  unsigned long parent_rate)
+{
+	struct si5324_hw_data *hwdata =
+		container_of(hw, struct si5324_hw_data, hw);
+
+	u32 ncn_ls, n2_ls, n3n, actual_rate;
+	u8 n1_hs, n2_hs, bwsel, buf[SI5324_OUT_REGS * 2];
+	int i, ret, rc;
+
+	ret = si5324_calcfreqsettings(SI5324_REF_CLOCK, rate, &actual_rate,
+				      &n1_hs, &ncn_ls, &n2_hs, &n2_ls, &n3n,
+				      &bwsel);
+	if (ret < 0)
+		return ret;
+
+	hwdata->drvdata->rate_clkout0 = rate;
+	i = 0;
+
+	/* Enable Free running mode */
+	buf[i] = SI5324_CONTROL;
+	buf[i + 1] = SI5324_FREE_RUN_EN;
+	i += 2;
+
+	/* Loop bandwidth */
+	buf[i] = SI5324_BWSEL;
+	buf[i + 1] = (bwsel << SI5324_BWSEL_SHIFT) | SI5324_BWSEL_DEF_VAL;
+	i += 2;
+
+	/* Enable reference clock 2 in free running mode */
+	buf[i] = SI5324_POWERDOWN;
+	/* Enable input clock 2, Disable input clock 1 */
+	buf[i + 1] = SI5324_PD_CK1_DIS;
+	i += 2;
+
+	/* N1_HS */
+	buf[i] = SI5324_N1_HS;
+	buf[i + 1] = n1_hs << SI5324_N1_HS_VAL_SHIFT;
+	i += 2;
+
+	/* NC1_LS */
+	buf[i] = SI5324_NC1_LS_H;
+	buf[i + 1] = (u8)((ncn_ls & 0x000F0000) >> 16);
+	buf[i + 2] = SI5324_NC1_LS_M;
+	buf[i + 3] = (u8)((ncn_ls & 0x0000FF00) >> 8);
+	buf[i + 4] = SI5324_NC1_LS_L;
+	buf[i + 5] = (u8)(ncn_ls & 0x000000FF);
+	i += 6;
+
+	/* N2_HS and N2_LS */
+	buf[i] = SI5324_N2_HS_LS_H;
+	buf[i + 1] = (n2_hs << SI5324_N2_HS_LS_H_VAL_SHIFT);
+	buf[i + 1] |= (u8)((n2_ls & 0x000F0000) >> 16);
+	buf[i + 2] = SI5324_N2_LS_H;
+	buf[i + 3] = (u8)((n2_ls & 0x0000FF00) >> 8);
+	buf[i + 4] = SI5324_N2_LS_L;
+	buf[i + 5] = (u8)(n2_ls & 0x000000FF);
+	i += 6;
+
+	/* N32 (CLKIN2 or XTAL in FREERUNNING mode) */
+	buf[i] = SI5324_N32_CLKIN_H;
+	buf[i + 2] = SI5324_N32_CLKIN_M;
+	buf[i + 4] = SI5324_N32_CLKIN_L;
+	buf[i + 1] = (u8)((n3n & 0x00070000) >> 16);
+	buf[i + 3] = (u8)((n3n & 0x0000FF00) >> 8);
+	buf[i + 5] = (u8)(n3n & 0x000000FF);
+	i += 6;
+
+	/* Start calibration */
+	buf[i] = SI5324_RESET_CALIB;
+	buf[i + 1] = SI5324_CALIB_EN;
+	i += 2;
+
+	hwdata->drvdata->params.valid = 0;
+	rc = si5324_bulk_scatter_write(hwdata->drvdata, SI5324_OUT_REGS, buf);
+
+	return rc;
+}
+
+static const struct clk_ops si5324_clkout_ops = {
+	.prepare = si5324_clkout_prepare,
+	.unprepare = si5324_clkout_unprepare,
+	.recalc_rate = si5324_clkout_recalc_rate,
+	.round_rate = si5324_clkout_round_rate,
+	.set_rate = si5324_clkout_set_rate,
+};
+
+static const struct of_device_id si5324_dt_ids[] = {
+	{ .compatible = "silabs,si5319" },
+	{ .compatible = "silabs,si5324" },
+	{ .compatible = "silabs,si5328" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, si5324_dt_ids);
+
+static int si5324_dt_parse(struct i2c_client *client)
+{
+	struct device_node *child, *np = client->dev.of_node;
+	struct si5324_platform_data *pdata;
+	struct property *prop;
+	const __be32 *p;
+	int num = 0;
+	u32 val;
+
+	if (!np)
+		return 0;
+
+	pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	/*
+	 * property silabs,pll-source : <num src>, [<..>]
+	 * allow to selectively set pll source
+	 */
+	of_property_for_each_u32(np, "silabs,pll-source", prop, p, num) {
+		if (num >= 1) {
+			dev_err(&client->dev,
+				"invalid pll %d on pll-source prop\n", num);
+			return -EINVAL;
+		}
+		p = of_prop_next_u32(prop, p, &val);
+		if (!p) {
+			dev_err(&client->dev,
+				"missing pll-source for pll %d\n", num);
+			return -EINVAL;
+		}
+
+		switch (val) {
+		case 0:
+			dev_dbg(&client->dev, "using xtal as parent for pll\n");
+			pdata->pll_src = SI5324_PLL_SRC_XTAL;
+			break;
+		case 1:
+			dev_dbg(&client->dev,
+				"using clkin1 as parent for pll\n");
+			pdata->pll_src = SI5324_PLL_SRC_CLKIN1;
+			break;
+		case 2:
+			dev_dbg(&client->dev,
+				"using clkin2 as parent for pll\n");
+			pdata->pll_src = SI5324_PLL_SRC_CLKIN2;
+			break;
+		default:
+			dev_err(&client->dev,
+				"invalid parent %d for pll %d\n", val, num);
+			return -EINVAL;
+		}
+	}
+	/* per clkout properties */
+	for_each_child_of_node(np, child) {
+		if (of_property_read_u32(child, "reg", &num)) {
+			dev_err(&client->dev, "missing reg property of %s\n",
+				child->name);
+			goto put_child;
+		}
+
+		if (num >= 2) {
+			dev_err(&client->dev, "invalid clkout %d\n", num);
+			goto put_child;
+		}
+
+		if (!of_property_read_u32(child, "silabs,drive-strength",
+					  &val)) {
+			switch (val) {
+			case SI5324_DRIVE_2MA:
+			case SI5324_DRIVE_4MA:
+			case SI5324_DRIVE_6MA:
+			case SI5324_DRIVE_8MA:
+				pdata->clkout[num].drive = val;
+				break;
+			default:
+				dev_err(&client->dev,
+					"invalid drive strength %d for clkout %d\n",
+					val, num);
+				goto put_child;
+			}
+		}
+
+		if (!of_property_read_u32(child, "clock-frequency", &val)) {
+			dev_dbg(&client->dev, "clock-frequency = %u\n", val);
+			pdata->clkout[num].rate = val;
+		} else {
+			dev_err(&client->dev,
+				"missing clock-frequency property of %s\n",
+				child->name);
+			goto put_child;
+		}
+	}
+	client->dev.platform_data = pdata;
+
+	return 0;
+put_child:
+	of_node_put(child);
+	return -EINVAL;
+}
+
+static u8 instance;
+
+static int si5324_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct si5324_platform_data *pdata;
+	struct si5324_driver_data *drvdata;
+	struct clk_init_data init;
+	struct clk *clk;
+	const char *parent_names[3];
+	char inst_names[NUM_NAME_IDS][MAX_NAME_LEN];
+	u8 num_parents, num_clocks;
+	int ret, n;
+	enum si53xx_variant variant = id->driver_data;
+
+	if (variant > si5328) {
+		dev_err(&client->dev, "si53xx device not present\n");
+		return -ENODEV;
+	}
+
+	dev_info(&client->dev, "%s probed\n", si53xx_variant_name[variant]);
+	ret = si5324_dt_parse(client);
+	if (ret)
+		return ret;
+
+	pdata = client->dev.platform_data;
+	if (!pdata)
+		return -EINVAL;
+
+	drvdata = devm_kzalloc(&client->dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata)
+		return -ENOMEM;
+
+	drvdata->client = client;
+	drvdata->pxtal = devm_clk_get(&client->dev, "xtal");
+	drvdata->pclkin1 = devm_clk_get(&client->dev, "clkin1");
+	drvdata->pclkin2 = devm_clk_get(&client->dev, "clkin2");
+
+	if (PTR_ERR(drvdata->pxtal) == -EPROBE_DEFER ||
+	    PTR_ERR(drvdata->pclkin1) == -EPROBE_DEFER ||
+	    PTR_ERR(drvdata->pclkin2) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	drvdata->regmap = devm_regmap_init_i2c(client, &si5324_regmap_config);
+	if (IS_ERR(drvdata->regmap)) {
+		dev_err(&client->dev, "failed to allocate register map\n");
+		return PTR_ERR(drvdata->regmap);
+	}
+
+	i2c_set_clientdata(client, drvdata);
+	si5324_initialize(drvdata);
+
+	/* setup input clock configuration */
+	ret = si5324_pll_reparent(drvdata, 0, pdata->pll_src);
+	if (ret) {
+		dev_err(&client->dev,
+			"failed to reparent pll to %d\n",
+			pdata->pll_src);
+		return ret;
+	}
+
+	for (n = 0; n < SI5324_MAX_CLKOUTS; n++) {
+		ret = si5324_clkout_set_drive_strength(drvdata, n,
+						       pdata->clkout[n].drive);
+		if (ret) {
+			dev_err(&client->dev,
+				"failed set drive strength of clkout%d to %d\n",
+				n, pdata->clkout[n].drive);
+			return ret;
+		}
+	}
+
+	if (!IS_ERR(drvdata->pxtal))
+		clk_prepare_enable(drvdata->pxtal);
+	if (!IS_ERR(drvdata->pclkin1))
+		clk_prepare_enable(drvdata->pclkin1);
+	if (!IS_ERR(drvdata->pclkin2))
+		clk_prepare_enable(drvdata->pclkin2);
+
+	/* create instance names by appending instance id */
+	for (n = 0; n < SI5324_SRC_CLKS; n++) {
+		sprintf(inst_names[n], "%s_%d", si5324_input_names[n],
+			instance);
+	}
+	sprintf(inst_names[3], "%s_%d", si5324_pll_name, instance);
+	for (n = 0; n < SI5324_MAX_CLKOUTS; n++) {
+		sprintf(inst_names[n + 4], "%s_%d", si5324_clkout_names[n],
+			instance);
+	}
+
+	/* register xtal input clock gate */
+	memset(&init, 0, sizeof(init));
+	init.name = inst_names[0];
+	init.ops = &si5324_xtal_ops;
+	init.flags = 0;
+
+	if (!IS_ERR(drvdata->pxtal)) {
+		drvdata->pxtal_name = __clk_get_name(drvdata->pxtal);
+		init.parent_names = &drvdata->pxtal_name;
+		init.num_parents = 1;
+	}
+	drvdata->xtal.init = &init;
+
+	clk = devm_clk_register(&client->dev, &drvdata->xtal);
+	if (IS_ERR(clk)) {
+		dev_err(&client->dev, "unable to register %s\n", init.name);
+		ret = PTR_ERR(clk);
+		goto err_clk;
+	}
+
+	/* register clkin1 input clock gate */
+	memset(&init, 0, sizeof(init));
+	init.name = inst_names[1];
+	init.ops = &si5324_clkin_ops;
+	if (!IS_ERR(drvdata->pclkin1)) {
+		drvdata->pclkin1_name = __clk_get_name(drvdata->pclkin1);
+		init.parent_names = &drvdata->pclkin1_name;
+		init.num_parents = 1;
+	}
+
+	drvdata->clkin1.init = &init;
+	clk = devm_clk_register(&client->dev, &drvdata->clkin1);
+	if (IS_ERR(clk)) {
+		dev_err(&client->dev, "unable to register %s\n",
+			init.name);
+		ret = PTR_ERR(clk);
+		goto err_clk;
+	}
+
+	/* register clkin2 input clock gate */
+	memset(&init, 0, sizeof(init));
+	init.name = inst_names[2];
+	init.ops = &si5324_clkin_ops;
+	if (!IS_ERR(drvdata->pclkin2)) {
+		drvdata->pclkin2_name = __clk_get_name(drvdata->pclkin2);
+		init.parent_names = &drvdata->pclkin2_name;
+		init.num_parents = 1;
+	}
+
+	drvdata->clkin2.init = &init;
+	clk = devm_clk_register(&client->dev, &drvdata->clkin2);
+	if (IS_ERR(clk)) {
+		dev_err(&client->dev, "unable to register %s\n",
+			init.name);
+		ret = PTR_ERR(clk);
+		goto err_clk;
+	}
+
+	/* Si5324 allows to mux xtal or clkin1 or clkin2 to PLL input */
+	num_parents = SI5324_SRC_CLKS;
+	parent_names[0] = inst_names[0];
+	parent_names[1] = inst_names[1];
+	parent_names[2] = inst_names[2];
+
+	/* register PLL */
+	drvdata->pll.drvdata = drvdata;
+	drvdata->pll.hw.init = &init;
+	memset(&init, 0, sizeof(init));
+	init.name = inst_names[3];
+	init.ops = &si5324_pll_ops;
+	init.flags = 0;
+	init.flags |= CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE;
+	init.parent_names = parent_names;
+	init.num_parents = num_parents;
+
+	clk = devm_clk_register(&client->dev, &drvdata->pll.hw);
+	if (IS_ERR(clk)) {
+		dev_err(&client->dev, "unable to register %s\n", init.name);
+		ret = PTR_ERR(clk);
+		goto err_clk;
+	}
+
+	/* register clk out divider */
+	num_clocks = 2;
+	num_parents = 1;
+	parent_names[0] = inst_names[3];
+
+	drvdata->clkout = devm_kzalloc(&client->dev, num_clocks *
+				       sizeof(*drvdata->clkout), GFP_KERNEL);
+
+	drvdata->onecell.clk_num = num_clocks;
+	drvdata->onecell.clks = devm_kzalloc(&client->dev,
+					     num_clocks *
+					     sizeof(*drvdata->onecell.clks),
+					     GFP_KERNEL);
+
+	if (WARN_ON(!drvdata->clkout) || !drvdata->onecell.clks) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
+
+	for (n = 0; n < num_clocks; n++) {
+		drvdata->clkout[n].num = n;
+		drvdata->clkout[n].drvdata = drvdata;
+		drvdata->clkout[n].hw.init = &init;
+		memset(&init, 0, sizeof(init));
+		init.name = inst_names[4 + n];
+		init.ops = &si5324_clkout_ops;
+		init.flags = 0;
+		init.flags |= CLK_SET_RATE_PARENT;
+		init.parent_names = parent_names;
+		init.num_parents = num_parents;
+
+		clk = devm_clk_register(&client->dev, &drvdata->clkout[n].hw);
+		if (IS_ERR(clk)) {
+			dev_err(&client->dev, "unable to register %s\n",
+				init.name);
+			ret = PTR_ERR(clk);
+			goto err_clk;
+		}
+		/* refer to output clock in onecell */
+		drvdata->onecell.clks[n] = clk;
+
+		/* set initial clkout rate */
+		if (pdata->clkout[n].rate != 0) {
+			int ret;
+
+			ret = clk_set_rate(clk, pdata->clkout[n].rate);
+			if (ret != 0) {
+				dev_err(&client->dev, "Cannot set rate : %d\n",
+					ret);
+			}
+		}
+	}
+
+	ret = of_clk_add_provider(client->dev.of_node, of_clk_src_onecell_get,
+				  &drvdata->onecell);
+	if (ret) {
+		dev_err(&client->dev, "unable to add clk provider\n");
+		goto err_clk;
+	}
+
+	dev_info(&client->dev, "%s probe successful\n",
+		 si53xx_variant_name[variant]);
+	instance++;
+	return 0;
+
+err_clk:
+	if (!IS_ERR(drvdata->pxtal))
+		clk_disable_unprepare(drvdata->pxtal);
+	if (!IS_ERR(drvdata->pclkin1))
+		clk_disable_unprepare(drvdata->pclkin1);
+	if (!IS_ERR(drvdata->pclkin2))
+		clk_disable_unprepare(drvdata->pclkin2);
+
+	return ret;
+}
+
+static int si5324_i2c_remove(struct i2c_client *client)
+{
+	of_clk_del_provider(client->dev.of_node);
+	return 0;
+}
+
+static const struct i2c_device_id si5324_i2c_ids[] = {
+	{ "si5319", si5319 },
+	{ "si5324", si5324 },
+	{ "si5328", si5328 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, si5324_i2c_ids);
+
+static struct i2c_driver si5324_driver = {
+	.driver = {
+		.name = "si5324",
+		.of_match_table = of_match_ptr(si5324_dt_ids),
+	},
+	.probe = si5324_i2c_probe,
+	.remove = si5324_i2c_remove,
+	.id_table = si5324_i2c_ids,
+};
+module_i2c_driver(si5324_driver);
+
+MODULE_AUTHOR("Venkateshwar Rao G <vgannava@xilinx.com>");
+MODULE_DESCRIPTION("Silicon Labs 5319/5324/5328 clock driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-si5324.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-si5324.h
@@ -0,0 +1,140 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Si5324 clock driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Authors:	Leon Woestenberg <leon@sidebranch.com>
+ *		Venkateshwar Rao <vgannava@xilinx.com>
+ */
+
+#ifndef _CLK_SI5324_H_
+#define _CLK_SI5324_H_
+
+#define SI5324_BUS_BASE_ADDR		0x68
+
+#define SI5324_CONTROL			0
+#define SI5324_CONTROL_FREE_RUN		BIT(6)
+#define SI5324_FREE_RUN_EN		0x54
+
+#define SI5324_INCK_PRIOR		1
+#define SI5324_INCK_PRIOR_1_MASK	0xC
+#define SI5324_INCK_PRIOI_2_MASK	0x3
+
+#define SI5324_BWSEL			2
+#define SI5324_BWSEL_MASK		0xF0
+#define SI5324_BWSEL_SHIFT		4
+#define SI5324_BWSEL_DEF_VAL		2
+
+#define SI5324_CKSEL			3
+#define SI5324_CKSEL_SQL_ICAL		BIT(4)
+#define SI5324_CKSEL_SHIFT		6
+#define SI5324_CK_SEL			3
+
+#define SI3324_AUTOSEL			4
+#define SI5324_AUTOSEL_DEF		0x12
+
+#define SI5324_ICMOS			5
+#define SI5324_OUTPUT_SIGFMT		6
+#define SI5324_OUTPUT_SF1_DEFAULT	0xF
+#define SI5324_REFFRE_FOS		7
+#define SI5324_HLOG			8
+#define SI5324_AVG_HIST			9
+#define SI5324_DSBL_CLKOUT		10
+#define SI5324_DSBL_CLKOUT2		BIT(3)
+#define SI5324_POWERDOWN		11
+#define SI5324_PD_CK1			BIT(0)
+#define SI5324_PD_CK2			BIT(1)
+#define SI5324_PD_CK1_DIS		0x41
+#define SI5324_PD_CK2_DIS		0x42
+#define SI5324_FOS_LOCKT		19
+#define SI5324_FOS_DEFAULT		0x23
+#define SI5324_CK_ACTV_SEL		21
+#define SI5324_CK_DEFAULT		0xFC
+#define SI5324_CK_ACTV			BIT(1)
+#define SI5324_CK_SELPIN		BIT(1)
+#define SI5324_LOS_MSK			23
+#define SI5324_FOS_L0L_MASK		24
+
+/* output clock dividers */
+#define SI5324_N1_HS			25
+#define SI5324_N1_HS_VAL_SHIFT		5
+#define SI5324_HSHIFT			16
+#define SI5324_LSHIFT			8
+#define SI5324_NC1_LS_H			31
+#define SI5324_NC1_LS_M			32
+#define SI5324_NC1_LS_L			33
+#define SI5324_DIV_LS_MASK		0x0F
+#define SI5324_DIV_HS_MASK		0xF0
+#define SI5324_NC2_LS_H			34
+#define SI5324_NC2_LS_M			35
+#define SI5324_NC2_LS_L			36
+
+#define SI5324_N2_HS_LS_H		40
+#define SI5324_N2_HS_LS_H_VAL_SHIFT	5
+#define SI5324_N2_LS_H			41
+#define SI5324_N2_LS_L			42
+#define SI5324_N31_CLKIN_H		43
+#define SI5324_N31_CLKIN_M		44
+#define SI5324_N31_CLKIN_L		45
+#define SI5324_N32_CLKIN_H		46
+#define SI5324_N32_CLKIN_M		47
+#define SI5324_N32_CLKIN_L		48
+#define SI5324_FOS_CLKIN_RATE		55
+#define SI5324_PLL_ACTV_CLK		128
+#define SI5324_LOS_STATUS		129
+#define SI5324_CLKIN_LOL_STATUS		130
+#define SI5324_LOS_FLG			131
+#define SI5324_FOS_FLG			132
+#define SI5324_PARTNO_H			134
+#define SI5324_PARTNO_L			135
+
+#define SI5324_RESET_CALIB		136
+#define SI5324_RST_ALL			BIT(7)
+#define SI5324_CALIB_EN			BIT(6)
+
+#define SI5324_FASTLOCK			137
+#define SI5324_FASTLOCK_EN		BIT(0)
+#define SI5324_LOS1_LOS2_EN		138
+#define SI5324_SKEW1			142
+#define SI5324_SKEW2			143
+
+/* selects 2kHz to 710 MHz */
+#define SI5324_CLKIN_MIN_FREQ		2000
+#define SI5324_CLKIN_MAX_FREQ		(710 * 1000 * 1000)
+
+/* generates 2kHz to 945 MHz */
+#define SI5324_CLKOUT_MIN_FREQ		2000
+#define SI5324_CLKOUT_MAX_FREQ		(945 * 1000 * 1000)
+
+/* The following constants define the limits of the divider settings. */
+#define SI5324_N1_HS_MIN		6
+#define SI5324_N1_HS_MAX		11
+#define SI5324_NC_LS_MIN		1
+#define SI5324_NC_LS_MAX		0x100000
+#define SI5324_N2_HS_MIN		4
+#define SI5324_N2_HS_MAX		11
+#define SI5324_N2_LS_MIN		2
+#define SI5324_N2_LS_MAX		0x100000
+#define SI5324_N3_MIN			1
+#define SI5324_N3_MAX			0x080000
+
+#define SI5324_SRC_XTAL			0
+#define SI5324_SRC_CLKIN1		1
+#define SI5324_SRC_CLKIN2		2
+#define SI5324_SRC_CLKS			3
+
+#define SI5324_CLKIN1			0
+#define SI5324_CLKIN2			1
+#define SI5324_MAX_CLKOUTS		2
+#define NUM_NAME_IDS			6 /* 3 clkin, 1 pll, 2 clkout */
+#define MAX_NAME_LEN			11
+#define SI5324_PARAM_LEN		24
+#define SI5324_NC_PARAM_LEN		6
+#define SI5324_OUT_REGS			14
+#define SI5324_N1_PARAM_LEN		1
+#define SI5324_N2_PARAM_LEN		9
+#define SI5324_REF_CLOCK		114285000UL
+#define SI5324_RESET_DELAY_MS		20
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-si5341.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-si5341.c
@@ -798,6 +798,15 @@
 	u32 r_divider;
 	u8 r[3];
 
+	err = regmap_read(output->data->regmap,
+			SI5341_OUT_CONFIG(output), &val);
+	if (err < 0)
+		return err;
+
+	/* If SI5341_OUT_CFG_RDIV_FORCE2 is set, r_divider is 2 */
+	if (val & SI5341_OUT_CFG_RDIV_FORCE2)
+		return parent_rate / 2;
+
 	err = regmap_bulk_read(output->data->regmap,
 			SI5341_OUT_R_REG(output), r, 3);
 	if (err < 0)
@@ -814,13 +823,6 @@
 	r_divider += 1;
 	r_divider <<= 1;
 
-	err = regmap_read(output->data->regmap,
-			SI5341_OUT_CONFIG(output), &val);
-	if (err < 0)
-		return err;
-
-	if (val & SI5341_OUT_CFG_RDIV_FORCE2)
-		r_divider = 2;
 
 	return parent_rate / r_divider;
 }
@@ -890,10 +892,8 @@
 	r[0] = r_div ? (r_div & 0xff) : 1;
 	r[1] = (r_div >> 8) & 0xff;
 	r[2] = (r_div >> 16) & 0xff;
-	err = regmap_bulk_write(output->data->regmap,
+	return regmap_bulk_write(output->data->regmap,
 			SI5341_OUT_R_REG(output), r, 3);
-
-	return 0;
 }
 
 static int si5341_output_reparent(struct clk_si5341_output *output, u8 index)
@@ -1552,7 +1552,7 @@
 	struct clk_init_data init;
 	struct clk *input;
 	const char *root_clock_name;
-	const char *synth_clock_names[SI5341_NUM_SYNTH];
+	const char *synth_clock_names[SI5341_NUM_SYNTH] = { NULL };
 	int err;
 	unsigned int i;
 	struct clk_si5341_output_config config[SI5341_MAX_NUM_OUTPUTS];
@@ -1696,6 +1696,10 @@
 	for (i = 0; i < data->num_synth; ++i) {
 		synth_clock_names[i] = devm_kasprintf(&client->dev, GFP_KERNEL,
 				"%s.N%u", client->dev.of_node->name, i);
+		if (!synth_clock_names[i]) {
+			err = -ENOMEM;
+			goto free_clk_names;
+		}
 		init.name = synth_clock_names[i];
 		data->synth[i].index = i;
 		data->synth[i].data = data;
@@ -1704,6 +1708,7 @@
 		if (err) {
 			dev_err(&client->dev,
 				"synth N%u registration failed\n", i);
+			goto free_clk_names;
 		}
 	}
 
@@ -1713,6 +1718,10 @@
 	for (i = 0; i < data->num_outputs; ++i) {
 		init.name = kasprintf(GFP_KERNEL, "%s.%d",
 			client->dev.of_node->name, i);
+		if (!init.name) {
+			err = -ENOMEM;
+			goto free_clk_names;
+		}
 		init.flags = config[i].synth_master ? CLK_SET_RATE_PARENT : 0;
 		data->clk[i].index = i;
 		data->clk[i].data = data;
@@ -1734,17 +1743,17 @@
 		if (err) {
 			dev_err(&client->dev,
 				"output %u registration failed\n", i);
-			goto cleanup;
+			goto free_clk_names;
 		}
 		if (config[i].always_on)
 			clk_prepare(data->clk[i].hw.clk);
 	}
 
-	err = of_clk_add_hw_provider(client->dev.of_node, of_clk_si5341_get,
+	err = devm_of_clk_add_hw_provider(&client->dev, of_clk_si5341_get,
 			data);
 	if (err) {
 		dev_err(&client->dev, "unable to add clk provider\n");
-		goto cleanup;
+		goto free_clk_names;
 	}
 
 	if (initialization_required) {
@@ -1752,11 +1761,11 @@
 		regcache_cache_only(data->regmap, false);
 		err = regcache_sync(data->regmap);
 		if (err < 0)
-			goto cleanup;
+			goto free_clk_names;
 
 		err = si5341_finalize_defaults(data);
 		if (err < 0)
-			goto cleanup;
+			goto free_clk_names;
 	}
 
 	/* wait for device to report input clock present and PLL lock */
@@ -1765,32 +1774,31 @@
 	       10000, 250000);
 	if (err) {
 		dev_err(&client->dev, "Error waiting for input clock or PLL lock\n");
-		goto cleanup;
+		goto free_clk_names;
 	}
 
 	/* clear sticky alarm bits from initialization */
 	err = regmap_write(data->regmap, SI5341_STATUS_STICKY, 0);
 	if (err) {
 		dev_err(&client->dev, "unable to clear sticky status\n");
-		goto cleanup;
+		goto free_clk_names;
 	}
 
 	err = sysfs_create_files(&client->dev.kobj, si5341_attributes);
-	if (err) {
+	if (err)
 		dev_err(&client->dev, "unable to create sysfs files\n");
-		goto cleanup;
-	}
 
+free_clk_names:
 	/* Free the names, clk framework makes copies */
 	for (i = 0; i < data->num_synth; ++i)
 		 devm_kfree(&client->dev, (void *)synth_clock_names[i]);
 
-	return 0;
-
 cleanup:
-	for (i = 0; i < SI5341_MAX_NUM_OUTPUTS; ++i) {
-		if (data->clk[i].vddo_reg)
-			regulator_disable(data->clk[i].vddo_reg);
+	if (err) {
+		for (i = 0; i < SI5341_MAX_NUM_OUTPUTS; ++i) {
+			if (data->clk[i].vddo_reg)
+				regulator_disable(data->clk[i].vddo_reg);
+		}
 	}
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-stm32f4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-stm32f4.c
@@ -129,7 +129,6 @@
 	{ STM32F4_RCC_APB2ENR, 20,	"spi5",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 21,	"spi6",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 22,	"sai1",		"apb2_div" },
-	{ STM32F4_RCC_APB2ENR, 26,	"ltdc",		"apb2_div" },
 };
 
 static const struct stm32f4_gate_data stm32f469_gates[] __initconst = {
@@ -211,7 +210,6 @@
 	{ STM32F4_RCC_APB2ENR, 20,	"spi5",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 21,	"spi6",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 22,	"sai1",		"apb2_div" },
-	{ STM32F4_RCC_APB2ENR, 26,	"ltdc",		"apb2_div" },
 };
 
 static const struct stm32f4_gate_data stm32f746_gates[] __initconst = {
@@ -286,7 +284,6 @@
 	{ STM32F4_RCC_APB2ENR, 21,	"spi6",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 22,	"sai1",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 23,	"sai2",		"apb2_div" },
-	{ STM32F4_RCC_APB2ENR, 26,	"ltdc",		"apb2_div" },
 };
 
 static const struct stm32f4_gate_data stm32f769_gates[] __initconst = {
@@ -364,7 +361,6 @@
 	{ STM32F4_RCC_APB2ENR, 21,	"spi6",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 22,	"sai1",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 23,	"sai2",		"apb2_div" },
-	{ STM32F4_RCC_APB2ENR, 26,	"ltdc",		"apb2_div" },
 	{ STM32F4_RCC_APB2ENR, 30,	"mdio",		"apb2_div" },
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-versaclock5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-versaclock5.c
@@ -992,6 +992,11 @@
 	}
 
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.mux", client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
+
 	init.ops = &vc5_mux_ops;
 	init.flags = 0;
 	init.parent_names = parent_names;
@@ -1006,6 +1011,10 @@
 		memset(&init, 0, sizeof(init));
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.dbl",
 				      client->dev.of_node);
+		if (!init.name) {
+			ret = -ENOMEM;
+			goto err_clk;
+		}
 		init.ops = &vc5_dbl_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
@@ -1021,6 +1030,10 @@
 	/* Register PFD */
 	memset(&init, 0, sizeof(init));
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.pfd", client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
 	init.ops = &vc5_pfd_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.parent_names = parent_names;
@@ -1038,6 +1051,10 @@
 	/* Register PLL */
 	memset(&init, 0, sizeof(init));
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.pll", client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
 	init.ops = &vc5_pll_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.parent_names = parent_names;
@@ -1057,6 +1074,10 @@
 		memset(&init, 0, sizeof(init));
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.fod%d",
 				      client->dev.of_node, idx);
+		if (!init.name) {
+			ret = -ENOMEM;
+			goto err_clk;
+		}
 		init.ops = &vc5_fod_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
@@ -1075,6 +1096,10 @@
 	memset(&init, 0, sizeof(init));
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.out0_sel_i2cb",
 			      client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
 	init.ops = &vc5_clk_out_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.parent_names = parent_names;
@@ -1101,6 +1126,10 @@
 		memset(&init, 0, sizeof(init));
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.out%d",
 				      client->dev.of_node, idx + 1);
+		if (!init.name) {
+			ret = -ENOMEM;
+			goto err_clk;
+		}
 		init.ops = &vc5_clk_out_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
@@ -1204,7 +1233,7 @@
 	.model = IDT_VC6_5P49V6901,
 	.clk_fod_cnt = 4,
 	.clk_out_cnt = 5,
-	.flags = VC5_HAS_PFD_FREQ_DBL,
+	.flags = VC5_HAS_PFD_FREQ_DBL | VC5_HAS_BYPASS_SYNC_BIT,
 };
 
 static const struct vc5_chip_info idt_5p49v6965_info = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-versaclock7.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-versaclock7.c
@@ -0,0 +1,1292 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common clock framework driver for the Versaclock7 family of timing devices.
+ *
+ * Copyright (c) 2022 Renesas Electronics Corporation
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/i2c.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/regmap.h>
+#include <linux/swab.h>
+
+/*
+ * 16-bit register address: the lower 8 bits of the register address come
+ * from the offset addr byte and the upper 8 bits come from the page register.
+ */
+#define VC7_PAGE_ADDR			0xFD
+#define VC7_PAGE_WINDOW			256
+#define VC7_MAX_REG			0x364
+
+/* Maximum number of banks supported by VC7 */
+#define VC7_NUM_BANKS			7
+
+/* Maximum number of FODs supported by VC7 */
+#define VC7_NUM_FOD			3
+
+/* Maximum number of IODs supported by VC7 */
+#define VC7_NUM_IOD			4
+
+/* Maximum number of outputs supported by VC7 */
+#define VC7_NUM_OUT			12
+
+/* VCO valid range is 9.5 GHz to 10.7 GHz */
+#define VC7_APLL_VCO_MIN		9500000000UL
+#define VC7_APLL_VCO_MAX		10700000000UL
+
+/* APLL denominator is fixed at 2^27 */
+#define VC7_APLL_DENOMINATOR_BITS	27
+
+/* FOD 1st stage denominator is fixed 2^34 */
+#define VC7_FOD_DENOMINATOR_BITS	34
+
+/* IOD can operate between 1kHz and 650MHz */
+#define VC7_IOD_RATE_MIN		1000UL
+#define VC7_IOD_RATE_MAX		650000000UL
+#define VC7_IOD_MIN_DIVISOR		14
+#define VC7_IOD_MAX_DIVISOR		0x1ffffff /* 25-bit */
+
+#define VC7_FOD_RATE_MIN		1000UL
+#define VC7_FOD_RATE_MAX		650000000UL
+#define VC7_FOD_1ST_STAGE_RATE_MIN	33000000UL /* 33 MHz */
+#define VC7_FOD_1ST_STAGE_RATE_MAX	650000000UL /* 650 MHz */
+#define VC7_FOD_1ST_INT_MAX		324
+#define VC7_FOD_2ND_INT_MIN		2
+#define VC7_FOD_2ND_INT_MAX		0x1ffff /* 17-bit */
+
+/* VC7 Registers */
+
+#define VC7_REG_XO_CNFG			0x2C
+#define VC7_REG_XO_CNFG_COUNT		4
+#define VC7_REG_XO_IB_H_DIV_SHIFT	24
+#define VC7_REG_XO_IB_H_DIV_MASK	GENMASK(28, VC7_REG_XO_IB_H_DIV_SHIFT)
+
+#define VC7_REG_APLL_FB_DIV_FRAC	0x120
+#define VC7_REG_APLL_FB_DIV_FRAC_COUNT	4
+#define VC7_REG_APLL_FB_DIV_FRAC_MASK	GENMASK(26, 0)
+
+#define VC7_REG_APLL_FB_DIV_INT		0x124
+#define VC7_REG_APLL_FB_DIV_INT_COUNT	2
+#define VC7_REG_APLL_FB_DIV_INT_MASK	GENMASK(9, 0)
+
+#define VC7_REG_APLL_CNFG		0x127
+#define VC7_REG_APLL_EN_DOUBLER		BIT(0)
+
+#define VC7_REG_OUT_BANK_CNFG(idx)	(0x280 + (0x4 * (idx)))
+#define VC7_REG_OUTPUT_BANK_SRC_MASK	GENMASK(2, 0)
+
+#define VC7_REG_FOD_INT_CNFG(idx)	(0x1E0 + (0x10 * (idx)))
+#define VC7_REG_FOD_INT_CNFG_COUNT	8
+#define VC7_REG_FOD_1ST_INT_MASK	GENMASK(8, 0)
+#define VC7_REG_FOD_2ND_INT_SHIFT	9
+#define VC7_REG_FOD_2ND_INT_MASK	GENMASK(25, VC7_REG_FOD_2ND_INT_SHIFT)
+#define VC7_REG_FOD_FRAC_SHIFT		26
+#define VC7_REG_FOD_FRAC_MASK		GENMASK_ULL(59, VC7_REG_FOD_FRAC_SHIFT)
+
+#define VC7_REG_IOD_INT_CNFG(idx)	(0x1C0 + (0x8 * (idx)))
+#define VC7_REG_IOD_INT_CNFG_COUNT	4
+#define VC7_REG_IOD_INT_MASK		GENMASK(24, 0)
+
+#define VC7_REG_ODRV_EN(idx)		(0x240 + (0x4 * (idx)))
+#define VC7_REG_OUT_DIS			BIT(0)
+
+struct vc7_driver_data;
+static const struct regmap_config vc7_regmap_config;
+
+/* Supported Renesas VC7 models */
+enum vc7_model {
+	VC7_RC21008A,
+};
+
+struct vc7_chip_info {
+	const enum vc7_model model;
+	const unsigned int banks[VC7_NUM_BANKS];
+	const unsigned int num_banks;
+	const unsigned int outputs[VC7_NUM_OUT];
+	const unsigned int num_outputs;
+};
+
+/*
+ * Changing the APLL frequency is currently not supported.
+ * The APLL will consist of an opaque block between the XO and FOD/IODs and
+ * its frequency will be computed based on the current state of the device.
+ */
+struct vc7_apll_data {
+	struct clk *clk;
+	struct vc7_driver_data *vc7;
+	u8 xo_ib_h_div;
+	u8 en_doubler;
+	u16 apll_fb_div_int;
+	u32 apll_fb_div_frac;
+};
+
+struct vc7_fod_data {
+	struct clk_hw hw;
+	struct vc7_driver_data *vc7;
+	unsigned int num;
+	u32 fod_1st_int;
+	u32 fod_2nd_int;
+	u64 fod_frac;
+};
+
+struct vc7_iod_data {
+	struct clk_hw hw;
+	struct vc7_driver_data *vc7;
+	unsigned int num;
+	u32 iod_int;
+};
+
+struct vc7_out_data {
+	struct clk_hw hw;
+	struct vc7_driver_data *vc7;
+	unsigned int num;
+	unsigned int out_dis;
+};
+
+struct vc7_driver_data {
+	struct i2c_client *client;
+	struct regmap *regmap;
+	const struct vc7_chip_info *chip_info;
+
+	struct clk *pin_xin;
+	struct vc7_apll_data clk_apll;
+	struct vc7_fod_data clk_fod[VC7_NUM_FOD];
+	struct vc7_iod_data clk_iod[VC7_NUM_IOD];
+	struct vc7_out_data clk_out[VC7_NUM_OUT];
+};
+
+struct vc7_bank_src_map {
+	enum vc7_bank_src_type {
+		VC7_FOD,
+		VC7_IOD,
+	} type;
+	union _divider {
+		struct vc7_iod_data *iod;
+		struct vc7_fod_data *fod;
+	} src;
+};
+
+static struct clk_hw *vc7_of_clk_get(struct of_phandle_args *clkspec,
+				     void *data)
+{
+	struct vc7_driver_data *vc7 = data;
+	unsigned int idx = clkspec->args[0];
+
+	if (idx >= vc7->chip_info->num_outputs)
+		return ERR_PTR(-EINVAL);
+
+	return &vc7->clk_out[idx].hw;
+}
+
+static const unsigned int RC21008A_index_to_output_mapping[] = {
+	1, 2, 3, 6, 7, 8, 10, 11
+};
+
+static int vc7_map_index_to_output(const enum vc7_model model, const unsigned int i)
+{
+	switch (model) {
+	case VC7_RC21008A:
+		return RC21008A_index_to_output_mapping[i];
+	default:
+		return i;
+	}
+}
+
+/* bank to output mapping, same across all variants */
+static const unsigned int output_bank_mapping[] = {
+	0, /* Output 0 */
+	1, /* Output 1 */
+	2, /* Output 2 */
+	2, /* Output 3 */
+	3, /* Output 4 */
+	3, /* Output 5 */
+	3, /* Output 6 */
+	3, /* Output 7 */
+	4, /* Output 8 */
+	4, /* Output 9 */
+	5, /* Output 10 */
+	6  /* Output 11 */
+};
+
+/**
+ * vc7_64_mul_64_to_128() - Multiply two u64 and return an unsigned 128-bit integer
+ * as an upper and lower part.
+ *
+ * @left: The left argument.
+ * @right: The right argument.
+ * @hi: The upper 64-bits of the 128-bit product.
+ * @lo: The lower 64-bits of the 128-bit product.
+ *
+ * From mul_64_64 in crypto/ecc.c:350 in the linux kernel, accessed in v5.17.2.
+ */
+static void vc7_64_mul_64_to_128(u64 left, u64 right, u64 *hi, u64 *lo)
+{
+	u64 a0 = left & 0xffffffffull;
+	u64 a1 = left >> 32;
+	u64 b0 = right & 0xffffffffull;
+	u64 b1 = right >> 32;
+	u64 m0 = a0 * b0;
+	u64 m1 = a0 * b1;
+	u64 m2 = a1 * b0;
+	u64 m3 = a1 * b1;
+
+	m2 += (m0 >> 32);
+	m2 += m1;
+
+	/* Overflow */
+	if (m2 < m1)
+		m3 += 0x100000000ull;
+
+	*lo = (m0 & 0xffffffffull) | (m2 << 32);
+	*hi = m3 + (m2 >> 32);
+}
+
+/**
+ * vc7_128_div_64_to_64() - Divides a 128-bit uint by a 64-bit divisor, return a 64-bit quotient.
+ *
+ * @numhi: The uppper 64-bits of the dividend.
+ * @numlo: The lower 64-bits of the dividend.
+ * @den: The denominator (divisor).
+ * @r: The remainder, pass NULL if the remainder is not needed.
+ *
+ * Originally from libdivide, modified to use kernel u64/u32 types.
+ *
+ * See https://github.com/ridiculousfish/libdivide/blob/master/libdivide.h#L471.
+ *
+ * Return: The 64-bit quotient of the division.
+ *
+ * In case of overflow of division by zero, max(u64) is returned.
+ */
+static u64 vc7_128_div_64_to_64(u64 numhi, u64 numlo, u64 den, u64 *r)
+{
+	// We work in base 2**32.
+	// A uint32 holds a single digit. A uint64 holds two digits.
+	// Our numerator is conceptually [num3, num2, num1, num0].
+	// Our denominator is [den1, den0].
+	const u64 b = ((u64)1 << 32);
+
+	// The high and low digits of our computed quotient.
+	u32 q1, q0;
+
+	// The normalization shift factor
+	int shift;
+
+	// The high and low digits of our denominator (after normalizing).
+	// Also the low 2 digits of our numerator (after normalizing).
+	u32 den1, den0, num1, num0;
+
+	// A partial remainder;
+	u64 rem;
+
+	// The estimated quotient, and its corresponding remainder (unrelated to true remainder).
+	u64 qhat, rhat;
+
+	// Variables used to correct the estimated quotient.
+	u64 c1, c2;
+
+	// Check for overflow and divide by 0.
+	if (numhi >= den) {
+		if (r)
+			*r = ~0ull;
+		return ~0ull;
+	}
+
+	// Determine the normalization factor. We multiply den by this, so that its leading digit
+	// is at least half b. In binary this means just shifting left by the number of leading
+	// zeros, so that there's a 1 in the MSB.
+	// We also shift numer by the same amount. This cannot overflow because numhi < den.
+	// The expression (-shift & 63) is the same as (64 - shift), except it avoids the UB of
+	// shifting by 64. The funny bitwise 'and' ensures that numlo does not get shifted into
+	// numhi if shift is 0. clang 11 has an x86 codegen bug here: see LLVM bug 50118.
+	// The sequence below avoids it.
+	shift = __builtin_clzll(den);
+	den <<= shift;
+	numhi <<= shift;
+	numhi |= (numlo >> (-shift & 63)) & (-(s64)shift >> 63);
+	numlo <<= shift;
+
+	// Extract the low digits of the numerator and both digits of the denominator.
+	num1 = (u32)(numlo >> 32);
+	num0 = (u32)(numlo & 0xFFFFFFFFu);
+	den1 = (u32)(den >> 32);
+	den0 = (u32)(den & 0xFFFFFFFFu);
+
+	// We wish to compute q1 = [n3 n2 n1] / [d1 d0].
+	// Estimate q1 as [n3 n2] / [d1], and then correct it.
+	// Note while qhat may be 2 digits, q1 is always 1 digit.
+	qhat = div64_u64_rem(numhi, den1, &rhat);
+	c1 = qhat * den0;
+	c2 = rhat * b + num1;
+	if (c1 > c2)
+		qhat -= (c1 - c2 > den) ? 2 : 1;
+	q1 = (u32)qhat;
+
+	// Compute the true (partial) remainder.
+	rem = numhi * b + num1 - q1 * den;
+
+	// We wish to compute q0 = [rem1 rem0 n0] / [d1 d0].
+	// Estimate q0 as [rem1 rem0] / [d1] and correct it.
+	qhat = div64_u64_rem(rem, den1, &rhat);
+	c1 = qhat * den0;
+	c2 = rhat * b + num0;
+	if (c1 > c2)
+		qhat -= (c1 - c2 > den) ? 2 : 1;
+	q0 = (u32)qhat;
+
+	// Return remainder if requested.
+	if (r)
+		*r = (rem * b + num0 - q0 * den) >> shift;
+	return ((u64)q1 << 32) | q0;
+}
+
+static int vc7_get_bank_clk(struct vc7_driver_data *vc7,
+			    unsigned int bank_idx,
+			    unsigned int output_bank_src,
+			    struct vc7_bank_src_map *map)
+{
+	/* Mapping from Table 38 in datasheet */
+	if (bank_idx == 0 || bank_idx == 1) {
+		switch (output_bank_src) {
+		case 0:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[0];
+			return 0;
+		case 1:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[1];
+			return 0;
+		case 4:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[0];
+			return 0;
+		case 5:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[1];
+			return 0;
+		default:
+			break;
+		}
+	} else if (bank_idx == 2) {
+		switch (output_bank_src) {
+		case 1:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[1];
+			return 0;
+		case 4:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[0];
+			return 0;
+		case 5:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[1];
+			return 0;
+		default:
+			break;
+		}
+	} else if (bank_idx == 3) {
+		switch (output_bank_src) {
+		case 4:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[0];
+			return 0;
+		case 5:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[1];
+			return 0;
+		case 6:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[2];
+			return 0;
+		default:
+			break;
+		}
+	} else if (bank_idx == 4) {
+		switch (output_bank_src) {
+		case 0:
+			/* CLKIN1 not supported in this driver */
+			break;
+		case 2:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[2];
+			return 0;
+		case 5:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[1];
+			return 0;
+		case 6:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[2];
+			return 0;
+		case 7:
+			/* CLKIN0 not supported in this driver */
+			break;
+		default:
+			break;
+		}
+	} else if (bank_idx == 5) {
+		switch (output_bank_src) {
+		case 0:
+			/* CLKIN1 not supported in this driver */
+			break;
+		case 1:
+			/* XIN_REFIN not supported in this driver */
+			break;
+		case 2:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[2];
+			return 0;
+		case 3:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[3];
+			return 0;
+		case 5:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[1];
+			return 0;
+		case 6:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[2];
+			return 0;
+		case 7:
+			/* CLKIN0 not supported in this driver */
+			break;
+		default:
+			break;
+		}
+	} else if (bank_idx == 6) {
+		switch (output_bank_src) {
+		case 0:
+			/* CLKIN1 not supported in this driver */
+			break;
+		case 2:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[2];
+			return 0;
+		case 3:
+			map->type = VC7_IOD,
+			map->src.iod = &vc7->clk_iod[3];
+			return 0;
+		case 5:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[1];
+			return 0;
+		case 6:
+			map->type = VC7_FOD,
+			map->src.fod = &vc7->clk_fod[2];
+			return 0;
+		case 7:
+			/* CLKIN0 not supported in this driver */
+			break;
+		default:
+			break;
+		}
+	}
+
+	pr_warn("bank_src%d = %d is not supported\n", bank_idx, output_bank_src);
+	return -1;
+}
+
+static int vc7_read_apll(struct vc7_driver_data *vc7)
+{
+	int err;
+	u32 val32;
+	u16 val16;
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_XO_CNFG,
+			       (u32 *)&val32,
+			       VC7_REG_XO_CNFG_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read XO_CNFG\n");
+		return err;
+	}
+
+	vc7->clk_apll.xo_ib_h_div = (val32 & VC7_REG_XO_IB_H_DIV_MASK)
+		>> VC7_REG_XO_IB_H_DIV_SHIFT;
+
+	err = regmap_read(vc7->regmap,
+			  VC7_REG_APLL_CNFG,
+			  &val32);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read APLL_CNFG\n");
+		return err;
+	}
+
+	vc7->clk_apll.en_doubler = val32 & VC7_REG_APLL_EN_DOUBLER;
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_APLL_FB_DIV_FRAC,
+			       (u32 *)&val32,
+			       VC7_REG_APLL_FB_DIV_FRAC_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read APLL_FB_DIV_FRAC\n");
+		return err;
+	}
+
+	vc7->clk_apll.apll_fb_div_frac = val32 & VC7_REG_APLL_FB_DIV_FRAC_MASK;
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_APLL_FB_DIV_INT,
+			       (u16 *)&val16,
+			       VC7_REG_APLL_FB_DIV_INT_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read APLL_FB_DIV_INT\n");
+		return err;
+	}
+
+	vc7->clk_apll.apll_fb_div_int = val16 & VC7_REG_APLL_FB_DIV_INT_MASK;
+
+	return 0;
+}
+
+static int vc7_read_fod(struct vc7_driver_data *vc7, unsigned int idx)
+{
+	int err;
+	u64 val;
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_FOD_INT_CNFG(idx),
+			       (u64 *)&val,
+			       VC7_REG_FOD_INT_CNFG_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read FOD%d\n", idx);
+		return err;
+	}
+
+	vc7->clk_fod[idx].fod_1st_int = (val & VC7_REG_FOD_1ST_INT_MASK);
+	vc7->clk_fod[idx].fod_2nd_int =
+	    (val & VC7_REG_FOD_2ND_INT_MASK) >> VC7_REG_FOD_2ND_INT_SHIFT;
+	vc7->clk_fod[idx].fod_frac = (val & VC7_REG_FOD_FRAC_MASK)
+		>> VC7_REG_FOD_FRAC_SHIFT;
+
+	return 0;
+}
+
+static int vc7_write_fod(struct vc7_driver_data *vc7, unsigned int idx)
+{
+	int err;
+	u64 val;
+
+	/*
+	 * FOD dividers are part of an atomic group where fod_1st_int,
+	 * fod_2nd_int, and fod_frac must be written together. The new divider
+	 * is applied when the MSB of fod_frac is written.
+	 */
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_FOD_INT_CNFG(idx),
+			       (u64 *)&val,
+			       VC7_REG_FOD_INT_CNFG_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read FOD%d\n", idx);
+		return err;
+	}
+
+	val = u64_replace_bits(val,
+			       vc7->clk_fod[idx].fod_1st_int,
+			       VC7_REG_FOD_1ST_INT_MASK);
+	val = u64_replace_bits(val,
+			       vc7->clk_fod[idx].fod_2nd_int,
+			       VC7_REG_FOD_2ND_INT_MASK);
+	val = u64_replace_bits(val,
+			       vc7->clk_fod[idx].fod_frac,
+			       VC7_REG_FOD_FRAC_MASK);
+
+	err = regmap_bulk_write(vc7->regmap,
+				VC7_REG_FOD_INT_CNFG(idx),
+				(u64 *)&val,
+				sizeof(u64));
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to write FOD%d\n", idx);
+		return err;
+	}
+
+	return 0;
+}
+
+static int vc7_read_iod(struct vc7_driver_data *vc7, unsigned int idx)
+{
+	int err;
+	u32 val;
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_IOD_INT_CNFG(idx),
+			       (u32 *)&val,
+			       VC7_REG_IOD_INT_CNFG_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read IOD%d\n", idx);
+		return err;
+	}
+
+	vc7->clk_iod[idx].iod_int = (val & VC7_REG_IOD_INT_MASK);
+
+	return 0;
+}
+
+static int vc7_write_iod(struct vc7_driver_data *vc7, unsigned int idx)
+{
+	int err;
+	u32 val;
+
+	/*
+	 * IOD divider field is atomic and all bits must be written.
+	 * The new divider is applied when the MSB of iod_int is written.
+	 */
+
+	err = regmap_bulk_read(vc7->regmap,
+			       VC7_REG_IOD_INT_CNFG(idx),
+			       (u32 *)&val,
+			       VC7_REG_IOD_INT_CNFG_COUNT);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read IOD%d\n", idx);
+		return err;
+	}
+
+	val = u32_replace_bits(val,
+			       vc7->clk_iod[idx].iod_int,
+			       VC7_REG_IOD_INT_MASK);
+
+	err = regmap_bulk_write(vc7->regmap,
+				VC7_REG_IOD_INT_CNFG(idx),
+				(u32 *)&val,
+				sizeof(u32));
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to write IOD%d\n", idx);
+		return err;
+	}
+
+	return 0;
+}
+
+static int vc7_read_output(struct vc7_driver_data *vc7, unsigned int idx)
+{
+	int err;
+	unsigned int val, out_num;
+
+	out_num = vc7_map_index_to_output(vc7->chip_info->model, idx);
+	err = regmap_read(vc7->regmap,
+			  VC7_REG_ODRV_EN(out_num),
+			  &val);
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to read ODRV_EN[%d]\n", idx);
+		return err;
+	}
+
+	vc7->clk_out[idx].out_dis = val & VC7_REG_OUT_DIS;
+
+	return 0;
+}
+
+static int vc7_write_output(struct vc7_driver_data *vc7, unsigned int idx)
+{
+	int err;
+	unsigned int out_num;
+
+	out_num = vc7_map_index_to_output(vc7->chip_info->model, idx);
+	err = regmap_write_bits(vc7->regmap,
+				VC7_REG_ODRV_EN(out_num),
+				VC7_REG_OUT_DIS,
+				vc7->clk_out[idx].out_dis);
+
+	if (err) {
+		dev_err(&vc7->client->dev, "failed to write ODRV_EN[%d]\n", idx);
+		return err;
+	}
+
+	return 0;
+}
+
+static unsigned long vc7_get_apll_rate(struct vc7_driver_data *vc7)
+{
+	int err;
+	unsigned long xtal_rate;
+	u64 refin_div, apll_rate;
+
+	xtal_rate = clk_get_rate(vc7->pin_xin);
+	err = vc7_read_apll(vc7);
+	if (err) {
+		dev_err(&vc7->client->dev, "unable to read apll\n");
+		return err;
+	}
+
+	/* 0 is bypassed, 1 is reserved */
+	if (vc7->clk_apll.xo_ib_h_div < 2)
+		refin_div = xtal_rate;
+	else
+		refin_div = div64_u64(xtal_rate, vc7->clk_apll.xo_ib_h_div);
+
+	if (vc7->clk_apll.en_doubler)
+		refin_div *= 2;
+
+	/* divider = int + (frac / 2^27) */
+	apll_rate = (refin_div * vc7->clk_apll.apll_fb_div_int) +
+		    ((refin_div * vc7->clk_apll.apll_fb_div_frac) >> VC7_APLL_DENOMINATOR_BITS);
+
+	pr_debug("%s - xo_ib_h_div: %u, apll_fb_div_int: %u, apll_fb_div_frac: %u\n",
+		 __func__, vc7->clk_apll.xo_ib_h_div, vc7->clk_apll.apll_fb_div_int,
+		 vc7->clk_apll.apll_fb_div_frac);
+	pr_debug("%s - refin_div: %llu, apll rate: %llu\n",
+		 __func__, refin_div, apll_rate);
+
+	return apll_rate;
+}
+
+static void vc7_calc_iod_divider(unsigned long rate, unsigned long parent_rate,
+				 u32 *divider)
+{
+	*divider = DIV_ROUND_UP(parent_rate, rate);
+	if (*divider < VC7_IOD_MIN_DIVISOR)
+		*divider = VC7_IOD_MIN_DIVISOR;
+	if (*divider > VC7_IOD_MAX_DIVISOR)
+		*divider = VC7_IOD_MAX_DIVISOR;
+}
+
+static void vc7_calc_fod_1st_stage(unsigned long rate, unsigned long parent_rate,
+				   u32 *div_int, u64 *div_frac)
+{
+	u64 rem;
+
+	*div_int = (u32)div64_u64_rem(parent_rate, rate, &rem);
+	*div_frac = div64_u64(rem << VC7_FOD_DENOMINATOR_BITS, rate);
+}
+
+static unsigned long vc7_calc_fod_1st_stage_rate(unsigned long parent_rate,
+						 u32 fod_1st_int, u64 fod_frac)
+{
+	u64 numer, denom, hi, lo, divisor;
+
+	numer = fod_frac;
+	denom = BIT_ULL(VC7_FOD_DENOMINATOR_BITS);
+
+	if (fod_frac) {
+		vc7_64_mul_64_to_128(parent_rate, denom, &hi, &lo);
+		divisor = ((u64)fod_1st_int * denom) + numer;
+		return vc7_128_div_64_to_64(hi, lo, divisor, NULL);
+	}
+
+	return div64_u64(parent_rate, fod_1st_int);
+}
+
+static unsigned long vc7_calc_fod_2nd_stage_rate(unsigned long parent_rate,
+						 u32 fod_1st_int, u32 fod_2nd_int, u64 fod_frac)
+{
+	unsigned long fod_1st_stage_rate;
+
+	fod_1st_stage_rate = vc7_calc_fod_1st_stage_rate(parent_rate, fod_1st_int, fod_frac);
+
+	if (fod_2nd_int < 2)
+		return fod_1st_stage_rate;
+
+	/*
+	 * There is a div-by-2 preceding the 2nd stage integer divider
+	 * (not shown on block diagram) so the actual 2nd stage integer
+	 * divisor is 2 * N.
+	 */
+	return div64_u64(fod_1st_stage_rate >> 1, fod_2nd_int);
+}
+
+static void vc7_calc_fod_divider(unsigned long rate, unsigned long parent_rate,
+				 u32 *fod_1st_int, u32 *fod_2nd_int, u64 *fod_frac)
+{
+	unsigned int allow_frac, i, best_frac_i;
+	unsigned long first_stage_rate;
+
+	vc7_calc_fod_1st_stage(rate, parent_rate, fod_1st_int, fod_frac);
+	first_stage_rate = vc7_calc_fod_1st_stage_rate(parent_rate, *fod_1st_int, *fod_frac);
+
+	*fod_2nd_int = 0;
+
+	/* Do we need the second stage integer divider? */
+	if (first_stage_rate < VC7_FOD_1ST_STAGE_RATE_MIN) {
+		allow_frac = 0;
+		best_frac_i = VC7_FOD_2ND_INT_MIN;
+
+		for (i = VC7_FOD_2ND_INT_MIN; i <= VC7_FOD_2ND_INT_MAX; i++) {
+			/*
+			 * 1) There is a div-by-2 preceding the 2nd stage integer divider
+			 *    (not shown on block diagram) so the actual 2nd stage integer
+			 *    divisor is 2 * N.
+			 * 2) Attempt to find an integer solution first. This means stepping
+			 *    through each 2nd stage integer and recalculating the 1st stage
+			 *    until the 1st stage frequency is out of bounds. If no integer
+			 *    solution is found, use the best fractional solution.
+			 */
+			vc7_calc_fod_1st_stage(parent_rate, rate * 2 * i, fod_1st_int, fod_frac);
+			first_stage_rate = vc7_calc_fod_1st_stage_rate(parent_rate,
+								       *fod_1st_int,
+								       *fod_frac);
+
+			/* Remember the first viable fractional solution */
+			if (best_frac_i == VC7_FOD_2ND_INT_MIN &&
+			    first_stage_rate > VC7_FOD_1ST_STAGE_RATE_MIN) {
+				best_frac_i = i;
+			}
+
+			/* Is the divider viable? Prefer integer solutions over fractional. */
+			if (*fod_1st_int < VC7_FOD_1ST_INT_MAX &&
+			    first_stage_rate >= VC7_FOD_1ST_STAGE_RATE_MIN &&
+			    (allow_frac || *fod_frac == 0)) {
+				*fod_2nd_int = i;
+				break;
+			}
+
+			/* Ran out of divisors or the 1st stage frequency is out of range */
+			if (i >= VC7_FOD_2ND_INT_MAX ||
+			    first_stage_rate > VC7_FOD_1ST_STAGE_RATE_MAX) {
+				allow_frac = 1;
+				i = best_frac_i;
+
+				/* Restore the best frac and rerun the loop for the last time */
+				if (best_frac_i != VC7_FOD_2ND_INT_MIN)
+					i--;
+
+				continue;
+			}
+		}
+	}
+}
+
+static unsigned long vc7_fod_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+	struct vc7_fod_data *fod = container_of(hw, struct vc7_fod_data, hw);
+	struct vc7_driver_data *vc7 = fod->vc7;
+	int err;
+	unsigned long fod_rate;
+
+	err = vc7_read_fod(vc7, fod->num);
+	if (err) {
+		dev_err(&vc7->client->dev, "error reading registers for %s\n",
+			clk_hw_get_name(hw));
+		return err;
+	}
+
+	pr_debug("%s - %s: parent_rate: %lu\n", __func__, clk_hw_get_name(hw), parent_rate);
+
+	fod_rate = vc7_calc_fod_2nd_stage_rate(parent_rate, fod->fod_1st_int,
+					       fod->fod_2nd_int, fod->fod_frac);
+
+	pr_debug("%s - %s: fod_1st_int: %u, fod_2nd_int: %u, fod_frac: %llu\n",
+		 __func__, clk_hw_get_name(hw),
+		 fod->fod_1st_int, fod->fod_2nd_int, fod->fod_frac);
+	pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), fod_rate);
+
+	return fod_rate;
+}
+
+static long vc7_fod_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *parent_rate)
+{
+	struct vc7_fod_data *fod = container_of(hw, struct vc7_fod_data, hw);
+	unsigned long fod_rate;
+
+	pr_debug("%s - %s: requested rate: %lu, parent_rate: %lu\n",
+		 __func__, clk_hw_get_name(hw), rate, *parent_rate);
+
+	vc7_calc_fod_divider(rate, *parent_rate,
+			     &fod->fod_1st_int, &fod->fod_2nd_int, &fod->fod_frac);
+	fod_rate = vc7_calc_fod_2nd_stage_rate(*parent_rate, fod->fod_1st_int,
+					       fod->fod_2nd_int, fod->fod_frac);
+
+	pr_debug("%s - %s: fod_1st_int: %u, fod_2nd_int: %u, fod_frac: %llu\n",
+		 __func__, clk_hw_get_name(hw),
+		 fod->fod_1st_int, fod->fod_2nd_int, fod->fod_frac);
+	pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), fod_rate);
+
+	return fod_rate;
+}
+
+static int vc7_fod_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate)
+{
+	struct vc7_fod_data *fod = container_of(hw, struct vc7_fod_data, hw);
+	struct vc7_driver_data *vc7 = fod->vc7;
+	unsigned long fod_rate;
+
+	pr_debug("%s - %s: rate: %lu, parent_rate: %lu\n",
+		 __func__, clk_hw_get_name(hw), rate, parent_rate);
+
+	if (rate < VC7_FOD_RATE_MIN || rate > VC7_FOD_RATE_MAX) {
+		dev_err(&vc7->client->dev,
+			"requested frequency %lu Hz for %s is out of range\n",
+			rate, clk_hw_get_name(hw));
+		return -EINVAL;
+	}
+
+	vc7_write_fod(vc7, fod->num);
+
+	fod_rate = vc7_calc_fod_2nd_stage_rate(parent_rate, fod->fod_1st_int,
+					       fod->fod_2nd_int, fod->fod_frac);
+
+	pr_debug("%s - %s: fod_1st_int: %u, fod_2nd_int: %u, fod_frac: %llu\n",
+		 __func__, clk_hw_get_name(hw),
+		 fod->fod_1st_int, fod->fod_2nd_int, fod->fod_frac);
+	pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), fod_rate);
+
+	return 0;
+}
+
+static const struct clk_ops vc7_fod_ops = {
+	.recalc_rate = vc7_fod_recalc_rate,
+	.round_rate = vc7_fod_round_rate,
+	.set_rate = vc7_fod_set_rate,
+};
+
+static unsigned long vc7_iod_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+	struct vc7_iod_data *iod = container_of(hw, struct vc7_iod_data, hw);
+	struct vc7_driver_data *vc7 = iod->vc7;
+	int err;
+	unsigned long iod_rate;
+
+	err = vc7_read_iod(vc7, iod->num);
+	if (err) {
+		dev_err(&vc7->client->dev, "error reading registers for %s\n",
+			clk_hw_get_name(hw));
+		return err;
+	}
+
+	iod_rate = div64_u64(parent_rate, iod->iod_int);
+
+	pr_debug("%s - %s: iod_int: %u\n", __func__, clk_hw_get_name(hw), iod->iod_int);
+	pr_debug("%s - %s rate: %lu\n", __func__, clk_hw_get_name(hw), iod_rate);
+
+	return iod_rate;
+}
+
+static long vc7_iod_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *parent_rate)
+{
+	struct vc7_iod_data *iod = container_of(hw, struct vc7_iod_data, hw);
+	unsigned long iod_rate;
+
+	pr_debug("%s - %s: requested rate: %lu, parent_rate: %lu\n",
+		 __func__, clk_hw_get_name(hw), rate, *parent_rate);
+
+	vc7_calc_iod_divider(rate, *parent_rate, &iod->iod_int);
+	iod_rate = div64_u64(*parent_rate, iod->iod_int);
+
+	pr_debug("%s - %s: iod_int: %u\n", __func__, clk_hw_get_name(hw), iod->iod_int);
+	pr_debug("%s - %s rate: %ld\n", __func__, clk_hw_get_name(hw), iod_rate);
+
+	return iod_rate;
+}
+
+static int vc7_iod_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate)
+{
+	struct vc7_iod_data *iod = container_of(hw, struct vc7_iod_data, hw);
+	struct vc7_driver_data *vc7 = iod->vc7;
+	unsigned long iod_rate;
+
+	pr_debug("%s - %s: rate: %lu, parent_rate: %lu\n",
+		 __func__, clk_hw_get_name(hw), rate, parent_rate);
+
+	if (rate < VC7_IOD_RATE_MIN || rate > VC7_IOD_RATE_MAX) {
+		dev_err(&vc7->client->dev,
+			"requested frequency %lu Hz for %s is out of range\n",
+			rate, clk_hw_get_name(hw));
+		return -EINVAL;
+	}
+
+	vc7_write_iod(vc7, iod->num);
+
+	iod_rate = div64_u64(parent_rate, iod->iod_int);
+
+	pr_debug("%s - %s: iod_int: %u\n", __func__, clk_hw_get_name(hw), iod->iod_int);
+	pr_debug("%s - %s rate: %ld\n", __func__, clk_hw_get_name(hw), iod_rate);
+
+	return 0;
+}
+
+static const struct clk_ops vc7_iod_ops = {
+	.recalc_rate = vc7_iod_recalc_rate,
+	.round_rate = vc7_iod_round_rate,
+	.set_rate = vc7_iod_set_rate,
+};
+
+static int vc7_clk_out_prepare(struct clk_hw *hw)
+{
+	struct vc7_out_data *out = container_of(hw, struct vc7_out_data, hw);
+	struct vc7_driver_data *vc7 = out->vc7;
+	int err;
+
+	out->out_dis = 0;
+
+	err = vc7_write_output(vc7, out->num);
+	if (err) {
+		dev_err(&vc7->client->dev, "error writing registers for %s\n",
+			clk_hw_get_name(hw));
+		return err;
+	}
+
+	pr_debug("%s - %s: clk prepared\n", __func__, clk_hw_get_name(hw));
+
+	return 0;
+}
+
+static void vc7_clk_out_unprepare(struct clk_hw *hw)
+{
+	struct vc7_out_data *out = container_of(hw, struct vc7_out_data, hw);
+	struct vc7_driver_data *vc7 = out->vc7;
+	int err;
+
+	out->out_dis = 1;
+
+	err = vc7_write_output(vc7, out->num);
+	if (err) {
+		dev_err(&vc7->client->dev, "error writing registers for %s\n",
+			clk_hw_get_name(hw));
+		return;
+	}
+
+	pr_debug("%s - %s: clk unprepared\n", __func__, clk_hw_get_name(hw));
+}
+
+static int vc7_clk_out_is_enabled(struct clk_hw *hw)
+{
+	struct vc7_out_data *out = container_of(hw, struct vc7_out_data, hw);
+	struct vc7_driver_data *vc7 = out->vc7;
+	int err, is_enabled;
+
+	err = vc7_read_output(vc7, out->num);
+	if (err) {
+		dev_err(&vc7->client->dev, "error reading registers for %s\n",
+			clk_hw_get_name(hw));
+		return err;
+	}
+
+	is_enabled = !out->out_dis;
+
+	pr_debug("%s - %s: is_enabled=%d\n", __func__, clk_hw_get_name(hw), is_enabled);
+
+	return is_enabled;
+}
+
+static const struct clk_ops vc7_clk_out_ops = {
+	.prepare = vc7_clk_out_prepare,
+	.unprepare = vc7_clk_out_unprepare,
+	.is_enabled = vc7_clk_out_is_enabled,
+};
+
+static int vc7_probe(struct i2c_client *client)
+{
+	struct vc7_driver_data *vc7;
+	struct clk_init_data clk_init;
+	struct vc7_bank_src_map bank_src_map;
+	const char *node_name, *apll_name;
+	const char *parent_names[1];
+	unsigned int i, val, bank_idx, out_num;
+	unsigned long apll_rate;
+	int ret;
+
+	vc7 = devm_kzalloc(&client->dev, sizeof(*vc7), GFP_KERNEL);
+	if (!vc7)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, vc7);
+	vc7->client = client;
+	vc7->chip_info = of_device_get_match_data(&client->dev);
+
+	vc7->pin_xin = devm_clk_get(&client->dev, "xin");
+	if (PTR_ERR(vc7->pin_xin) == -EPROBE_DEFER) {
+		return dev_err_probe(&client->dev, -EPROBE_DEFER,
+				     "xin not specified\n");
+	}
+
+	vc7->regmap = devm_regmap_init_i2c(client, &vc7_regmap_config);
+	if (IS_ERR(vc7->regmap)) {
+		return dev_err_probe(&client->dev, PTR_ERR(vc7->regmap),
+				     "failed to allocate register map\n");
+	}
+
+	if (of_property_read_string(client->dev.of_node, "clock-output-names",
+				    &node_name))
+		node_name = client->dev.of_node->name;
+
+	/* Register APLL */
+	apll_rate = vc7_get_apll_rate(vc7);
+	apll_name = kasprintf(GFP_KERNEL, "%s_apll", node_name);
+	vc7->clk_apll.clk = clk_register_fixed_rate(&client->dev, apll_name,
+						    __clk_get_name(vc7->pin_xin),
+						    0, apll_rate);
+	kfree(apll_name); /* ccf made a copy of the name */
+	if (IS_ERR(vc7->clk_apll.clk)) {
+		return dev_err_probe(&client->dev, PTR_ERR(vc7->clk_apll.clk),
+				     "failed to register apll\n");
+	}
+
+	/* Register FODs */
+	for (i = 0; i < VC7_NUM_FOD; i++) {
+		memset(&clk_init, 0, sizeof(clk_init));
+		clk_init.name = kasprintf(GFP_KERNEL, "%s_fod%d", node_name, i);
+		clk_init.ops = &vc7_fod_ops;
+		clk_init.parent_names = parent_names;
+		parent_names[0] = __clk_get_name(vc7->clk_apll.clk);
+		clk_init.num_parents = 1;
+		vc7->clk_fod[i].num = i;
+		vc7->clk_fod[i].vc7 = vc7;
+		vc7->clk_fod[i].hw.init = &clk_init;
+		ret = devm_clk_hw_register(&client->dev, &vc7->clk_fod[i].hw);
+		if (ret)
+			goto err_clk_register;
+		kfree(clk_init.name); /* ccf made a copy of the name */
+	}
+
+	/* Register IODs */
+	for (i = 0; i < VC7_NUM_IOD; i++) {
+		memset(&clk_init, 0, sizeof(clk_init));
+		clk_init.name = kasprintf(GFP_KERNEL, "%s_iod%d", node_name, i);
+		clk_init.ops = &vc7_iod_ops;
+		clk_init.parent_names = parent_names;
+		parent_names[0] = __clk_get_name(vc7->clk_apll.clk);
+		clk_init.num_parents = 1;
+		vc7->clk_iod[i].num = i;
+		vc7->clk_iod[i].vc7 = vc7;
+		vc7->clk_iod[i].hw.init = &clk_init;
+		ret = devm_clk_hw_register(&client->dev, &vc7->clk_iod[i].hw);
+		if (ret)
+			goto err_clk_register;
+		kfree(clk_init.name); /* ccf made a copy of the name */
+	}
+
+	/* Register outputs */
+	for (i = 0; i < vc7->chip_info->num_outputs; i++) {
+		out_num = vc7_map_index_to_output(vc7->chip_info->model, i);
+
+		/*
+		 * This driver does not support remapping FOD/IOD to banks.
+		 * The device state is read and the driver is setup to match
+		 * the device's existing mapping.
+		 */
+		bank_idx = output_bank_mapping[out_num];
+
+		regmap_read(vc7->regmap, VC7_REG_OUT_BANK_CNFG(bank_idx), &val);
+		val &= VC7_REG_OUTPUT_BANK_SRC_MASK;
+
+		memset(&bank_src_map, 0, sizeof(bank_src_map));
+		ret = vc7_get_bank_clk(vc7, bank_idx, val, &bank_src_map);
+		if (ret) {
+			dev_err_probe(&client->dev, ret,
+				      "unable to register output %d\n", i);
+			return ret;
+		}
+
+		switch (bank_src_map.type) {
+		case VC7_FOD:
+			parent_names[0] = clk_hw_get_name(&bank_src_map.src.fod->hw);
+			break;
+		case VC7_IOD:
+			parent_names[0] = clk_hw_get_name(&bank_src_map.src.iod->hw);
+			break;
+		}
+
+		memset(&clk_init, 0, sizeof(clk_init));
+		clk_init.name = kasprintf(GFP_KERNEL, "%s_out%d", node_name, i);
+		clk_init.ops = &vc7_clk_out_ops;
+		clk_init.flags = CLK_SET_RATE_PARENT;
+		clk_init.parent_names = parent_names;
+		clk_init.num_parents = 1;
+		vc7->clk_out[i].num = i;
+		vc7->clk_out[i].vc7 = vc7;
+		vc7->clk_out[i].hw.init = &clk_init;
+		ret = devm_clk_hw_register(&client->dev, &vc7->clk_out[i].hw);
+		if (ret)
+			goto err_clk_register;
+		kfree(clk_init.name); /* ccf made a copy of the name */
+	}
+
+	ret = of_clk_add_hw_provider(client->dev.of_node, vc7_of_clk_get, vc7);
+	if (ret) {
+		dev_err_probe(&client->dev, ret, "unable to add clk provider\n");
+		goto err_clk;
+	}
+
+	return ret;
+
+err_clk_register:
+	dev_err_probe(&client->dev, ret,
+		      "unable to register %s\n", clk_init.name);
+	kfree(clk_init.name); /* ccf made a copy of the name */
+err_clk:
+	clk_unregister_fixed_rate(vc7->clk_apll.clk);
+	return ret;
+}
+
+static int vc7_remove(struct i2c_client *client)
+{
+	struct vc7_driver_data *vc7 = i2c_get_clientdata(client);
+
+	of_clk_del_provider(client->dev.of_node);
+	clk_unregister_fixed_rate(vc7->clk_apll.clk);
+
+	return 0;
+}
+
+static bool vc7_volatile_reg(struct device *dev, unsigned int reg)
+{
+	if (reg == VC7_PAGE_ADDR)
+		return false;
+
+	return true;
+}
+
+static const struct vc7_chip_info vc7_rc21008a_info = {
+	.model = VC7_RC21008A,
+	.num_banks = 6,
+	.num_outputs = 8,
+};
+
+static struct regmap_range_cfg vc7_range_cfg[] = {
+{
+	.range_min = 0,
+	.range_max = VC7_MAX_REG,
+	.selector_reg = VC7_PAGE_ADDR,
+	.selector_mask = 0xFF,
+	.selector_shift = 0,
+	.window_start = 0,
+	.window_len = VC7_PAGE_WINDOW,
+}};
+
+static const struct regmap_config vc7_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = VC7_MAX_REG,
+	.ranges = vc7_range_cfg,
+	.num_ranges = ARRAY_SIZE(vc7_range_cfg),
+	.volatile_reg = vc7_volatile_reg,
+	.cache_type = REGCACHE_RBTREE,
+	.can_multi_write = true,
+	.reg_format_endian = REGMAP_ENDIAN_LITTLE,
+	.val_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+static const struct i2c_device_id vc7_i2c_id[] = {
+	{ "rc21008a", VC7_RC21008A },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, vc7_i2c_id);
+
+static const struct of_device_id vc7_of_match[] = {
+	{ .compatible = "renesas,rc21008a", .data = &vc7_rc21008a_info },
+	{},
+};
+MODULE_DEVICE_TABLE(of, vc7_of_match);
+
+static struct i2c_driver vc7_i2c_driver = {
+	.driver = {
+		.name = "vc7",
+		.of_match_table = vc7_of_match,
+	},
+	.probe_new = vc7_probe,
+	.remove = vc7_remove,
+	.id_table = vc7_i2c_id,
+};
+module_i2c_driver(vc7_i2c_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Alex Helms <alexander.helms.jy@renesas.com");
+MODULE_DESCRIPTION("Renesas Versaclock7 common clock framework driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-xlnx-clock-wizard-v.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-xlnx-clock-wizard-v.c
@@ -0,0 +1,765 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx 'Clocking Wizard' driver
+ *
+ *  Copyright (C) 2020 Xilinx
+ *
+ *  Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+ */
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/iopoll.h>
+
+#define WZRD_NUM_OUTPUTS	7
+#define WZRD_ACLK_MAX_FREQ	250000000UL
+
+#define WZRD_CLK_CFG_REG(n)	(0x330 + 4 * (n))
+
+#define WZRD_CLKFBOUT_1		0
+#define WZRD_CLKFBOUT_2		1
+#define WZRD_CLKOUT0_1		2
+#define WZRD_CLKOUT0_2		3
+#define WZRD_DESKEW_2		20
+#define WZRD_DIVCLK		21
+#define WZRD_CLKFBOUT_4		51
+#define WZRD_CLKFBOUT_3		48
+#define WZRD_DUTY_CYCLE		2
+#define WZRD_O_DIV		4
+
+#define WZRD_CLKFBOUT_FRAC_EN	BIT(1)
+#define WZRD_CLKFBOUT_PREDIV2	(BIT(11) | BIT(12) | BIT(9))
+#define WZRD_MULT_PREDIV2	(BIT(10) | BIT(9) | BIT(12))
+#define WZRD_CLKFBOUT_EDGE	BIT(8)
+#define WZRD_P5EN		BIT(13)
+#define WZRD_P5FEDGE		BIT(15)
+#define WZRD_DIVCLK_EDGE	BIT(10)
+#define WZRD_CLKOUT0_PREDIV2	BIT(11)
+
+#define WZRD_CLKFBOUT_L_SHIFT	0
+#define WZRD_CLKFBOUT_H_SHIFT	8
+#define WZRD_CLKFBOUT_L_MASK	GENMASK(7, 0)
+#define WZRD_CLKFBOUT_H_MASK	GENMASK(15, 8)
+#define WZRD_CLKFBOUT_FRAC_SHIFT	16
+#define WZRD_CLKFBOUT_FRAC_MASK		GENMASK(5, 0)
+#define WZRD_DIVCLK_DIVIDE_SHIFT	0
+#define WZRD_DIVCLK_DIVIDE_MASK		(0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
+#define WZRD_CLKOUT_DIVIDE_SHIFT	0
+#define WZRD_CLKOUT_DIVIDE_WIDTH	8
+#define WZRD_CLKOUT_DIVIDE_MASK		(0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
+#define WZRD_CLKOUT_FRAC_SHIFT		8
+#define WZRD_CLKOUT_FRAC_MASK		0x3ff
+
+#define WZRD_DR_MAX_INT_DIV_VALUE	32767
+#define WZRD_DR_STATUS_REG_OFFSET	0x04
+#define WZRD_DR_LOCK_BIT_MASK		0x00000001
+#define WZRD_DR_INIT_REG_OFFSET		0x14
+#define WZRD_DR_DIV_TO_PHASE_OFFSET	4
+#define WZRD_DR_BEGIN_DYNA_RECONF	0x03
+#define WZRD_MIN_ERR			500000
+#define WZRD_USEC_POLL			10
+#define WZRD_TIMEOUT_POLL		1000
+#define WZRD_FRAC_GRADIENT		64
+#define PREDIV2_MULT			2
+
+#define DIV_O				1
+#define DIV_ALL				3
+
+#define WZRD_M_MIN			4
+#define WZRD_M_MAX			432
+#define WZRD_D_MIN			1
+#define WZRD_D_MAX			123
+#define WZRD_VCO_MIN			2160000000
+#define WZRD_VCO_MAX			4320000000
+#define WZRD_O_MIN			2
+#define WZRD_O_MAX			511
+
+/* Get the mask from width */
+#define div_mask(width)			((1 << (width)) - 1)
+
+/* Extract divider instance from clock hardware instance */
+#define to_clk_wzrd_divider(_hw) container_of(_hw, struct clk_wzrd_divider, hw)
+
+enum clk_wzrd_int_clks {
+	wzrd_clk_mul,
+	wzrd_clk_mul_div,
+	wzrd_clk_mul_frac,
+	wzrd_clk_int_max
+};
+
+/**
+ * struct clk_wzrd - Clock wizard private data structure
+ *
+ * @clk_data:		Clock data
+ * @nb:			Notifier block
+ * @base:		Memory base
+ * @clk_in1:		Handle to input clock 'clk_in1'
+ * @axi_clk:		Handle to input clock 's_axi_aclk'
+ * @clks_internal:	Internal clocks
+ * @clkout:		Output clocks
+ * @suspended:		Flag indicating power state of the device
+ * @is_versal:		Flag indicating if it versal device
+ */
+struct clk_wzrd {
+	struct clk_onecell_data clk_data;
+	struct notifier_block nb;
+	void __iomem *base;
+	struct clk *clk_in1;
+	struct clk *axi_clk;
+	struct clk *clks_internal[wzrd_clk_int_max];
+	struct clk *clkout[WZRD_NUM_OUTPUTS];
+	bool suspended;
+	bool is_versal;
+};
+
+/**
+ * struct clk_wzrd_divider - clock divider specific to clk_wzrd
+ *
+ * @hw:		handle between common and hardware-specific interfaces
+ * @base:	base address of register containing the divider
+ * @offset:	offset address of register containing the divider
+ * @shift:	shift to the divider bit field
+ * @width:	width of the divider bit field
+ * @flags:	clk_wzrd divider flags
+ * @valuem:	value of the multiplier
+ * @valued:	value of the common divider
+ * @valueo:	value of the leaf divider
+ * @table:	array of value/divider pairs, last entry should have div = 0
+ * @lock:	register lock
+ */
+struct clk_wzrd_divider {
+	struct clk_hw hw;
+	void __iomem *base;
+	u16 offset;
+	u8 shift;
+	u8 width;
+	u8 flags;
+	u32 valuem;
+	u32 valued;
+	u32 valueo;
+	const struct clk_div_table *table;
+	spinlock_t *lock;  /* divider lock */
+};
+
+#define to_clk_wzrd(_nb) container_of(_nb, struct clk_wzrd, nb)
+
+/* spin lock variable for clk_wzrd */
+static DEFINE_SPINLOCK(clkwzrd_lock);
+
+static unsigned long clk_wzrd_recalc_rate_all(struct clk_hw *hw,
+					      unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	u32 edged, div, div2, p5en, edge, prediv2, all, regl, regh, mult, reg;
+
+	edge = !!(readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_1)) & WZRD_CLKFBOUT_EDGE);
+
+	reg = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_2));
+	regl = FIELD_GET(WZRD_CLKFBOUT_L_MASK, reg);
+	regh = FIELD_GET(WZRD_CLKFBOUT_H_MASK, reg);
+
+	mult = regl + regh + edge;
+	if (!mult)
+		mult = 1;
+
+	regl = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_4)) &
+		     WZRD_CLKFBOUT_FRAC_EN;
+	if (regl) {
+		regl = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_3)) &
+			WZRD_CLKFBOUT_FRAC_MASK;
+		mult = mult * WZRD_FRAC_GRADIENT + regl;
+		parent_rate = DIV_ROUND_CLOSEST((parent_rate * mult), WZRD_FRAC_GRADIENT);
+	} else {
+		parent_rate = parent_rate * mult;
+	}
+
+	/* O Calculation */
+	reg = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKOUT0_1));
+	edged = FIELD_GET(WZRD_CLKFBOUT_EDGE, reg);
+	p5en = FIELD_GET(WZRD_P5EN, reg);
+	prediv2 = FIELD_GET(WZRD_CLKOUT0_PREDIV2, reg);
+
+	reg = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKOUT0_2));
+	/* Low time */
+	regl = FIELD_GET(WZRD_CLKFBOUT_L_MASK, reg);
+	/* High time */
+	regh = FIELD_GET(WZRD_CLKFBOUT_H_MASK, reg);
+	all = regh + regl + edged;
+	if (!all)
+		all = 1;
+
+	if (prediv2)
+		div2 = PREDIV2_MULT * all + p5en;
+	else
+		div2 = all;
+
+	/* D calculation */
+	edged = !!(readl(divider->base + WZRD_CLK_CFG_REG(WZRD_DESKEW_2)) &
+		     WZRD_DIVCLK_EDGE);
+	reg = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_DIVCLK));
+	/* Low time */
+	regl = FIELD_GET(WZRD_CLKFBOUT_L_MASK, reg);
+	/* High time */
+	regh = FIELD_GET(WZRD_CLKFBOUT_H_MASK, reg);
+	div = regl + regh + edged;
+	if (!div)
+		div = 1;
+
+	div = div * div2;
+	return divider_recalc_rate(hw, parent_rate, div, divider->table,
+			divider->flags, divider->width);
+}
+
+static int clk_wzrd_get_divisors(struct clk_hw *hw, unsigned long rate,
+				 unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	u64 vco_freq, freq, diff;
+	u32 m, d, o;
+
+	for (m = WZRD_M_MIN; m <= WZRD_M_MAX; m++) {
+		for (d = WZRD_D_MIN; d <= WZRD_D_MAX; d++) {
+			vco_freq = DIV_ROUND_CLOSEST((parent_rate * m), d);
+			if (vco_freq >= WZRD_VCO_MIN && vco_freq <= WZRD_VCO_MAX) {
+				for (o = WZRD_O_MIN; o <= WZRD_O_MAX; o++) {
+					freq = DIV_ROUND_CLOSEST(vco_freq, o);
+					diff = abs(freq - rate);
+
+					if (diff < WZRD_MIN_ERR) {
+						divider->valuem = m;
+						divider->valued = d;
+						divider->valueo = o;
+						return 0;
+					}
+				}
+			}
+		}
+	}
+	return -EBUSY;
+}
+
+static int clk_wzrd_dynamic_all_nolock(struct clk_hw *hw, unsigned long rate,
+				       unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	u32 value, regh, edged, p5en, p5fedge, value2, m, regval, regval1;
+	int err;
+
+	err = clk_wzrd_get_divisors(hw, rate, parent_rate);
+	if (err)
+		return err;
+
+	writel(0, divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_4));
+
+	m = divider->valuem;
+	edged = m % WZRD_DUTY_CYCLE;
+	regh = m / WZRD_DUTY_CYCLE;
+	regval1 = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_1));
+	regval1 |= WZRD_MULT_PREDIV2;
+	if (edged)
+		regval1 = regval1 | WZRD_CLKFBOUT_EDGE;
+	else
+		regval1 = regval1 & ~WZRD_CLKFBOUT_EDGE;
+	writel(regval1, divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_1));
+	regval1 = regh | regh << WZRD_CLKFBOUT_H_SHIFT;
+	writel(regval1, divider->base + WZRD_CLK_CFG_REG(WZRD_CLKFBOUT_2));
+
+	value2 = divider->valued;
+	edged = value2 % WZRD_DUTY_CYCLE;
+	regh = (value2 / WZRD_DUTY_CYCLE);
+	regval1 = FIELD_PREP(WZRD_DIVCLK_EDGE, edged);
+	writel(regval1, divider->base + WZRD_CLK_CFG_REG(WZRD_DESKEW_2));
+	regval1 = regh | regh << WZRD_CLKFBOUT_H_SHIFT;
+	writel(regval1, divider->base + WZRD_CLK_CFG_REG(WZRD_DIVCLK));
+
+	value = divider->valueo;
+	regh = value / WZRD_O_DIV;
+	regval1 = readl(divider->base + WZRD_CLK_CFG_REG(WZRD_CLKOUT0_1));
+	regval1 |= WZRD_CLKFBOUT_PREDIV2;
+	regval1 = regval1 & ~(WZRD_CLKFBOUT_EDGE | WZRD_P5EN | WZRD_P5FEDGE);
+	if (value % WZRD_O_DIV > 1) {
+		edged = 1;
+		regval1 |= edged << WZRD_CLKFBOUT_H_SHIFT;
+	}
+	p5fedge = value % WZRD_DUTY_CYCLE;
+	p5en = value % WZRD_DUTY_CYCLE;
+
+	regval1 = regval1 | FIELD_PREP(WZRD_P5EN, p5en) | FIELD_PREP(WZRD_P5FEDGE, p5fedge);
+	writel(regval1, divider->base + WZRD_CLK_CFG_REG(WZRD_CLKOUT0_1));
+	regval = regh | regh << WZRD_CLKFBOUT_H_SHIFT;
+	writel(regval, divider->base + WZRD_CLK_CFG_REG(WZRD_CLKOUT0_2));
+
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
+				 value, value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+	if (err)
+		return err;
+
+	/* Initiate reconfiguration */
+	writel(WZRD_DR_BEGIN_DYNA_RECONF,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+	/* Check status register */
+	return  readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
+				 value, value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+}
+
+static int clk_wzrd_dynamic_all(struct clk_hw *hw, unsigned long rate,
+				unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	unsigned long flags = 0;
+	int ret;
+
+	if (divider->lock)
+		spin_lock_irqsave(divider->lock, flags);
+	else
+		__acquire(divider->lock);
+
+	ret = clk_wzrd_dynamic_all_nolock(hw, rate, parent_rate);
+
+	if (divider->lock)
+		spin_unlock_irqrestore(divider->lock, flags);
+	else
+		__release(divider->lock);
+
+	return ret;
+}
+
+static unsigned long clk_wzrd_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	void __iomem *div_addr =
+			(void __iomem *)((u64)divider->base + divider->offset);
+	unsigned int vall, valh;
+	u32 div;
+	u32 p5en, edge, prediv2;
+	u32 all;
+
+	edge = !!(readl(div_addr) & BIT(8));
+	p5en = !!(readl(div_addr) & BIT(13));
+	prediv2 = !!(readl(div_addr) & BIT(11));
+	vall = readl(div_addr + 4) & 0xff;
+	valh = readl(div_addr + 4) >> 8;
+	all = valh + vall + edge;
+	if (!all)
+		all = 1;
+	if (prediv2)
+		div =  (2 * all + prediv2 * p5en);
+	else
+		div = all;
+
+	return DIV_ROUND_UP_ULL((u64)parent_rate, div);
+}
+
+static int clk_wzrd_dynamic_reconfig(struct clk_hw *hw, unsigned long rate,
+				     unsigned long parent_rate)
+{
+	int err;
+	u32 value;
+	unsigned long flags = 0;
+	u32 regh, edged;
+	u32 p5en, p5fedge;
+	u32 regval, regval1;
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	void __iomem *div_addr =
+			(void __iomem *)((u64)divider->base + divider->offset);
+	if (divider->lock)
+		spin_lock_irqsave(divider->lock, flags);
+	else
+		__acquire(divider->lock);
+
+	value = DIV_ROUND_CLOSEST(parent_rate, rate);
+	regh = (value / 4);
+	regval = regh | (regh << 8);
+	regval1 = readl(div_addr);
+	regval1 |= WZRD_CLKFBOUT_PREDIV2;
+	regval1 = regval1 &  ~(BIT(8) | BIT(13) | BIT(15));
+	if (value % 4 > 1) {
+		edged = 1;
+		regval1 |= (edged << 8);
+	}
+	p5fedge = value % 2;
+	p5en = value % 2;
+	regval1 = regval1 | p5en << 13 | p5fedge << 15;
+	writel(regval1, div_addr);
+	regval = regh | regh << 8;
+	writel(regval, div_addr + 4);
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
+				 value, value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+	if (err)
+		goto err_reconfig;
+
+	/* Initiate reconfiguration */
+	writel(WZRD_DR_BEGIN_DYNA_RECONF,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
+				 value, value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+
+err_reconfig:
+	if (divider->lock)
+		spin_unlock_irqrestore(divider->lock, flags);
+	else
+		__release(divider->lock);
+
+	return err;
+}
+
+static long clk_wzrd_round_rate_all(struct clk_hw *hw, unsigned long rate,
+				    unsigned long *prate)
+{
+	return rate;
+}
+
+static long clk_wzrd_round_rate(struct clk_hw *hw, unsigned long rate,
+				unsigned long *prate)
+{
+	u8 div;
+
+	/*
+	 * since we donot change parent rate we just round rate to closest
+	 * achievable
+	 */
+	div = DIV_ROUND_CLOSEST(*prate, rate);
+
+	return (*prate / div);
+}
+
+static const struct clk_ops clk_wzrd_clk_divider_ops = {
+	.round_rate = clk_wzrd_round_rate,
+	.set_rate = clk_wzrd_dynamic_reconfig,
+	.recalc_rate = clk_wzrd_recalc_rate,
+};
+
+static const struct clk_ops clk_wzrd_clk_div_all_ops = {
+	.round_rate = clk_wzrd_round_rate_all,
+	.set_rate = clk_wzrd_dynamic_all,
+	.recalc_rate = clk_wzrd_recalc_rate_all,
+};
+
+static struct clk *clk_wzrd_register_divider(struct device *dev,
+					     const char *name,
+					     const char *parent_name,
+					     unsigned long flags,
+					     void __iomem *base, u16 offset,
+					     u8 shift, u8 width,
+					     u8 clk_divider_flags,
+					     u32 div_type,
+					     spinlock_t *lock)
+{
+	struct clk_wzrd_divider *div;
+	struct clk_hw *hw;
+	struct clk_init_data init;
+	int ret;
+
+	if (clk_divider_flags & CLK_DIVIDER_HIWORD_MASK) {
+		if (width + shift > 16) {
+			pr_warn("divider value exceeds LOWORD field\n");
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	/* allocate the divider */
+	div = kzalloc(sizeof(*div), GFP_KERNEL);
+	if (!div)
+		return ERR_PTR(-ENOMEM);
+
+	init.name = name;
+	if (clk_divider_flags & CLK_DIVIDER_READ_ONLY)
+		init.ops = &clk_divider_ro_ops;
+	else if (div_type == DIV_O)
+		init.ops = &clk_wzrd_clk_divider_ops;
+	else
+		init.ops = &clk_wzrd_clk_div_all_ops;
+
+	init.flags = flags;
+	init.parent_names = (parent_name ? &parent_name : NULL);
+	init.num_parents = (parent_name ? 1 : 0);
+
+	/* struct clk_divider assignments */
+	div->base = base;
+	div->offset = offset;
+	div->shift = shift;
+	div->width = width;
+	div->flags = clk_divider_flags;
+	div->lock = lock;
+	div->hw.init = &init;
+	div->table = NULL;
+
+	/* register the clock */
+	hw = &div->hw;
+	ret = clk_hw_register(dev, hw);
+	if (ret) {
+		kfree(div);
+		hw = ERR_PTR(ret);
+	}
+
+	return hw->clk;
+}
+
+static int __maybe_unused clk_wzrd_suspend(struct device *dev)
+{
+	struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(clk_wzrd->axi_clk);
+	clk_wzrd->suspended = true;
+
+	return 0;
+}
+
+static int __maybe_unused clk_wzrd_resume(struct device *dev)
+{
+	int ret;
+	struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
+
+	ret = clk_prepare_enable(clk_wzrd->axi_clk);
+	if (ret) {
+		dev_err(dev, "unable to enable s_axi_aclk\n");
+		return ret;
+	}
+
+	clk_wzrd->suspended = false;
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(clk_wzrd_dev_pm_ops, clk_wzrd_suspend,
+			 clk_wzrd_resume);
+
+static int clk_wzrd_probe(struct platform_device *pdev)
+{
+	int i, ret;
+	u32 regl, regh, edge, mult;
+	u32 regld, reghd, edged, div;
+	unsigned long rate;
+	const char *clk_name;
+	struct clk_wzrd *clk_wzrd;
+	struct resource *mem;
+	int outputs;
+	struct device_node *np = pdev->dev.of_node;
+
+	clk_wzrd = devm_kzalloc(&pdev->dev, sizeof(*clk_wzrd), GFP_KERNEL);
+	if (!clk_wzrd)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, clk_wzrd);
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	clk_wzrd->base = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(clk_wzrd->base))
+		return PTR_ERR(clk_wzrd->base);
+
+	clk_wzrd->clk_in1 = devm_clk_get(&pdev->dev, "clk_in1");
+	if (IS_ERR(clk_wzrd->clk_in1)) {
+		if (clk_wzrd->clk_in1 != ERR_PTR(-EPROBE_DEFER))
+			dev_err(&pdev->dev, "clk_in1 not found\n");
+		return PTR_ERR(clk_wzrd->clk_in1);
+	}
+
+	clk_wzrd->axi_clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+	if (IS_ERR(clk_wzrd->axi_clk)) {
+		if (clk_wzrd->axi_clk != ERR_PTR(-EPROBE_DEFER))
+			dev_err(&pdev->dev, "s_axi_aclk not found\n");
+		return PTR_ERR(clk_wzrd->axi_clk);
+	}
+	ret = clk_prepare_enable(clk_wzrd->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "enabling s_axi_aclk failed\n");
+		return ret;
+	}
+	rate = clk_get_rate(clk_wzrd->axi_clk);
+	if (rate > WZRD_ACLK_MAX_FREQ) {
+		dev_err(&pdev->dev, "s_axi_aclk frequency (%lu) too high\n",
+			rate);
+		ret = -EINVAL;
+		goto err_disable_clk;
+	}
+
+	outputs = of_property_count_strings(np, "clock-output-names");
+	clk_name = kasprintf(GFP_KERNEL, "%s_mul_div", dev_name(&pdev->dev));
+	if (!clk_name) {
+		ret = -ENOMEM;
+		goto err_rm_int_clk;
+	}
+
+	if (outputs == 1) {
+		const char *clkout_name;
+
+		if (of_property_read_string_index(np, "clock-output-names", i,
+						  &clkout_name)) {
+			dev_err(&pdev->dev,
+				"clock output name not specified\n");
+			ret = -EINVAL;
+			goto err_rm_int_clks;
+		}
+
+		clk_wzrd->clkout[0] = clk_wzrd_register_divider
+				(&pdev->dev, clkout_name,
+				__clk_get_name(clk_wzrd->clk_in1), 0,
+				clk_wzrd->base, WZRD_CLK_CFG_REG(3),
+				WZRD_CLKOUT_DIVIDE_SHIFT,
+				WZRD_CLKOUT_DIVIDE_WIDTH,
+				CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+				DIV_ALL, &clkwzrd_lock);
+
+		goto out;
+	}
+
+	/* register multiplier */
+	edge = !!(readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) & BIT(8));
+	regl = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(1)) &
+		     WZRD_CLKFBOUT_L_MASK) >> WZRD_CLKFBOUT_L_SHIFT;
+	regh = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(1)) &
+		     WZRD_CLKFBOUT_H_MASK) >> WZRD_CLKFBOUT_H_SHIFT;
+	mult = (regl  + regh + edge);
+	if (!mult)
+		mult = 1;
+	mult = mult * 64;
+
+	regl = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(51)) &
+		     WZRD_CLKFBOUT_FRAC_EN;
+	if (regl) {
+		regl = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(48)) &
+			WZRD_CLKFBOUT_FRAC_MASK;
+		mult = mult + regl;
+	}
+
+	clk_name = kasprintf(GFP_KERNEL, "%s_mul", dev_name(&pdev->dev));
+	if (!clk_name) {
+		ret = -ENOMEM;
+		goto err_disable_clk;
+	}
+	clk_wzrd->clks_internal[wzrd_clk_mul] = clk_register_fixed_factor
+			(&pdev->dev, clk_name,
+			 __clk_get_name(clk_wzrd->clk_in1),
+			0, mult, 64);
+	kfree(clk_name);
+	if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul])) {
+		dev_err(&pdev->dev, "unable to register fixed-factor clock\n");
+		ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul]);
+		goto err_disable_clk;
+	}
+
+	/* register div */
+	edged = !!(readl(clk_wzrd->base + WZRD_CLK_CFG_REG(20)) &
+		     BIT(10));
+	regld = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(21)) &
+		     WZRD_CLKFBOUT_L_MASK) >> WZRD_CLKFBOUT_L_SHIFT;
+	reghd = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(21)) &
+		     WZRD_CLKFBOUT_H_MASK) >> WZRD_CLKFBOUT_H_SHIFT;
+	div = (regld  + reghd + edged);
+	if (!div)
+		div = 1;
+	clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_fixed_factor
+			(&pdev->dev, clk_name,
+			 __clk_get_name(clk_wzrd->clks_internal[wzrd_clk_mul]),
+			0, 1, div);
+	if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div])) {
+		dev_err(&pdev->dev, "unable to register divider clock\n");
+		ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div]);
+		goto err_rm_int_clk;
+	}
+
+	/* register div per output */
+	for (i = outputs - 1; i >= 0 ; i--) {
+		const char *clkout_name;
+
+		if (of_property_read_string_index(np, "clock-output-names", i,
+						  &clkout_name)) {
+			dev_err(&pdev->dev,
+				"clock output name not specified\n");
+			ret = -EINVAL;
+			goto err_rm_int_clks;
+		}
+
+			clk_wzrd->clkout[i] = clk_wzrd_register_divider
+				(&pdev->dev, clkout_name,
+				clk_name, 0,
+				clk_wzrd->base, (WZRD_CLK_CFG_REG(3) + i * 8),
+				WZRD_CLKOUT_DIVIDE_SHIFT,
+				WZRD_CLKOUT_DIVIDE_WIDTH,
+				CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+				DIV_O, &clkwzrd_lock);
+
+		if (IS_ERR(clk_wzrd->clkout[i])) {
+			int j;
+
+			for (j = i + 1; j < outputs; j++)
+				clk_unregister(clk_wzrd->clkout[j]);
+			dev_err(&pdev->dev,
+				"unable to register divider clock\n");
+			ret = PTR_ERR(clk_wzrd->clkout[i]);
+			goto err_rm_int_clks;
+		}
+	}
+
+	kfree(clk_name);
+
+out:
+	clk_wzrd->clk_data.clks = clk_wzrd->clkout;
+	clk_wzrd->clk_data.clk_num = ARRAY_SIZE(clk_wzrd->clkout);
+	of_clk_add_provider(np, of_clk_src_onecell_get, &clk_wzrd->clk_data);
+
+	return 0;
+
+err_rm_int_clks:
+	clk_unregister(clk_wzrd->clks_internal[1]);
+err_rm_int_clk:
+	kfree(clk_name);
+	clk_unregister(clk_wzrd->clks_internal[0]);
+err_disable_clk:
+	clk_disable_unprepare(clk_wzrd->axi_clk);
+
+	return ret;
+}
+
+static int clk_wzrd_remove(struct platform_device *pdev)
+{
+	int i;
+	struct clk_wzrd *clk_wzrd = platform_get_drvdata(pdev);
+
+	of_clk_del_provider(pdev->dev.of_node);
+
+	for (i = 0; i < WZRD_NUM_OUTPUTS; i++)
+		clk_unregister(clk_wzrd->clkout[i]);
+	for (i = 0; i < wzrd_clk_int_max; i++)
+		clk_unregister(clk_wzrd->clks_internal[i]);
+
+	clk_disable_unprepare(clk_wzrd->axi_clk);
+
+	return 0;
+}
+
+static const struct of_device_id clk_wzrd_ids[] = {
+	{ .compatible = "xlnx,clk-wizard-1.0" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, clk_wzrd_ids);
+
+static struct platform_driver clk_wzrd_driver = {
+	.driver = {
+		.name = "clk-wizard",
+		.of_match_table = clk_wzrd_ids,
+		.pm = &clk_wzrd_dev_pm_ops,
+	},
+	.probe = clk_wzrd_probe,
+	.remove = clk_wzrd_remove,
+};
+module_platform_driver(clk_wzrd_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>");
+MODULE_DESCRIPTION("Driver for the Versal Clocking Wizard IP core");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk-xlnx-clock-wizard.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk-xlnx-clock-wizard.c
@@ -0,0 +1,860 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx 'Clocking Wizard' driver
+ *
+ *  Copyright (C) 2013 - 2014 Xilinx
+ *
+ *  Sören Brinkmann <soren.brinkmann@xilinx.com>
+ */
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/iopoll.h>
+
+#define WZRD_NUM_OUTPUTS	7
+#define WZRD_ACLK_MAX_FREQ	250000000UL
+
+#define WZRD_CLK_CFG_REG(n)	(0x200 + 4 * (n))
+
+#define WZRD_CLKOUT0_FRAC_EN	BIT(18)
+#define WZRD_CLKFBOUT_FRAC_EN	BIT(26)
+
+#define WZRD_CLKFBOUT_MULT_SHIFT	8
+#define WZRD_CLKFBOUT_MULT_MASK		GENMASK(15, 8)
+#define WZRD_CLKFBOUT_FRAC_SHIFT	16
+#define WZRD_CLKFBOUT_FRAC_MASK		(0x3ff << WZRD_CLKFBOUT_FRAC_SHIFT)
+#define WZRD_DIVCLK_DIVIDE_SHIFT	0
+#define WZRD_DIVCLK_DIVIDE_MASK		GENMASK(7, 0)
+#define WZRD_CLKOUT_DIVIDE_SHIFT	0
+#define WZRD_CLKOUT_DIVIDE_WIDTH	8
+#define WZRD_CLKOUT_DIVIDE_MASK		GENMASK(7, 0)
+#define WZRD_CLKOUT_FRAC_SHIFT		8
+#define WZRD_CLKOUT_FRAC_MASK		0x3ff
+#define WZRD_CLKOUT0_FRAC_MASK		GENMASK(17, 8)
+
+#define WZRD_DR_MAX_INT_DIV_VALUE	255
+#define WZRD_DR_STATUS_REG_OFFSET	0x04
+#define WZRD_DR_LOCK_BIT_MASK		0x00000001
+#define WZRD_DR_INIT_REG_OFFSET		0x25C
+#define WZRD_DR_DIV_TO_PHASE_OFFSET	4
+#define WZRD_DR_BEGIN_DYNA_RECONF	0x03
+#define WZRD_DR_BEGIN_DYNA_RECONF_5_2	0x07
+#define WZRD_DR_BEGIN_DYNA_RECONF1_5_2	0x02
+
+#define WZRD_USEC_POLL		10
+#define WZRD_TIMEOUT_POLL		1000
+
+/* Divider limits, from UG572 Table 3-4 for Ultrascale+ */
+#define DIV_O				0x01
+#define DIV_ALL				0x03
+
+#define WZRD_M_MIN			2
+#define WZRD_M_MAX			128
+#define WZRD_D_MIN			1
+#define WZRD_D_MAX			106
+#define WZRD_VCO_MIN			800000000
+#define WZRD_VCO_MAX			1600000000
+#define WZRD_O_MIN			1
+#define WZRD_O_MAX			128
+#define WZRD_MIN_ERR			20000
+#define WZRD_FRAC_POINTS		1000
+
+/* Get the mask from width */
+#define div_mask(width)			((1 << (width)) - 1)
+
+/* Extract divider instance from clock hardware instance */
+#define to_clk_wzrd_divider(_hw) container_of(_hw, struct clk_wzrd_divider, hw)
+
+enum clk_wzrd_int_clks {
+	wzrd_clk_mul = 0,
+	wzrd_clk_mul_div = 1,
+	wzrd_clk_mul_frac = 2,
+	wzrd_clk_int_max = 3,
+};
+
+/*
+ *         MMCM Block Diagram
+ *
+ *         +----------------+  +-----------------+
+ * input ->| vco_clk_div_hw |->| vco_clk_mul_hw  |--+
+ * rate    | (int divide)   |  | (frac multiply) |  |
+ *         +----------------+  +-----------------+  |
+ *                                                  |
+ *      +--------------------------------VCO-rate---+
+ *      |
+ *      |  +----------------+
+ *      +->| clkout[0]      |-> output0 rate
+ *      |  | (frac divide)  |
+ *      |  +----------------+
+ *      |
+ *      |  +----------------+
+ *      +->| clkout[1]      |-> output1 rate
+ *      |  | (int divide)   |
+ *      |  +----------------+
+ *      |
+ *     ...
+ *      |
+ *      |  +----------------+
+ *      +->| clkout[1]      |-> output6 rate
+ *         | (int divide)   |
+ *         +----------------+
+ */
+
+/**
+ * struct clk_wzrd - Clock wizard private data structure
+ *
+ * @clk_data:		Clock data
+ * @nb:			Notifier block
+ * @base:		Memory base
+ * @clk_in1:		Handle to input clock 'clk_in1'
+ * @axi_clk:		Handle to input clock 's_axi_aclk'
+ * @clks_internal:	Internal clocks
+ * @clkout:		Output clocks
+ * @speed_grade:	Speed grade of the device
+ * @suspended:		Flag indicating power state of the device
+ */
+struct clk_wzrd {
+	struct clk_onecell_data clk_data;
+	struct notifier_block nb;
+	void __iomem *base;
+	struct clk *clk_in1;
+	struct clk *axi_clk;
+	struct clk *clks_internal[wzrd_clk_int_max];
+	struct clk *clkout[WZRD_NUM_OUTPUTS];
+	unsigned int speed_grade;
+	bool suspended;
+};
+
+/**
+ * struct clk_wzrd_divider - clock divider specific to clk_wzrd
+ *
+ * @hw:		handle between common and hardware-specific interfaces
+ * @base:	base address of register containing the divider
+ * @offset:	offset address of register containing the divider
+ * @shift:	shift to the divider bit field
+ * @width:	width of the divider bit field
+ * @flags:	clk_wzrd divider flags
+ * @valuem:	value of the multiplier
+ * @valued:	value of the common divider
+ * @valueo:	value of the leaf divider
+ * @table:	array of value/divider pairs, last entry should have div = 0
+ * @lock:	register lock
+ */
+struct clk_wzrd_divider {
+	struct clk_hw hw;
+	void __iomem *base;
+	u16 offset;
+	u8 shift;
+	u8 width;
+	u8 flags;
+	const struct clk_div_table *table;
+	u32 valuem;
+	u32 valued;
+	u32 valueo;
+	spinlock_t *lock;  /* divider lock */
+};
+
+#define to_clk_wzrd(_nb) container_of(_nb, struct clk_wzrd, nb)
+
+/* maximum frequencies for input/output clocks per speed grade */
+static const unsigned long clk_wzrd_max_freq[] = {
+	800000000UL,
+	933000000UL,
+	1066000000UL
+};
+
+/* spin lock variable for clk_wzrd */
+static DEFINE_SPINLOCK(clkwzrd_lock);
+
+static unsigned long clk_wzrd_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	void __iomem *div_addr = divider->base + divider->offset;
+	unsigned int val;
+
+	val = readl(div_addr) >> divider->shift;
+	val &= div_mask(divider->width);
+
+	return divider_recalc_rate(hw, parent_rate, val, divider->table,
+			divider->flags, divider->width);
+}
+
+static int clk_wzrd_dynamic_reconfig(struct clk_hw *hw, unsigned long rate,
+				     unsigned long parent_rate)
+{
+	int err = 0;
+	u32 value;
+	unsigned long flags = 0;
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	void __iomem *div_addr = divider->base + divider->offset;
+
+	if (divider->lock)
+		spin_lock_irqsave(divider->lock, flags);
+	else
+		__acquire(divider->lock);
+
+	value = DIV_ROUND_CLOSEST(parent_rate, rate);
+
+	/* Cap the value to max */
+	min_t(u32, value, WZRD_DR_MAX_INT_DIV_VALUE);
+
+	/* Set divisor and clear phase offset */
+	writel(value, div_addr);
+	writel(0x00, div_addr + WZRD_DR_DIV_TO_PHASE_OFFSET);
+
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
+				 value, value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+	if (err)
+		goto err_reconfig;
+
+	/* Initiate reconfiguration */
+	writel(WZRD_DR_BEGIN_DYNA_RECONF_5_2,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+	writel(WZRD_DR_BEGIN_DYNA_RECONF1_5_2,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
+				 value, value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+err_reconfig:
+	if (divider->lock)
+		spin_unlock_irqrestore(divider->lock, flags);
+	else
+		__release(divider->lock);
+
+	return err;
+}
+
+static long clk_wzrd_round_rate(struct clk_hw *hw, unsigned long rate,
+				unsigned long *prate)
+{
+	u8 div;
+
+	/*
+	 * since we donot change parent rate we just round rate to closest
+	 * achievable
+	 */
+	div = DIV_ROUND_CLOSEST(*prate, rate);
+
+	return (*prate / div);
+}
+
+static u64 clk_wzrd_get_divisors(struct clk_hw *hw, unsigned long rate,
+				 unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	u64 vco_freq, freq, diff;
+	u32 m, d, o;
+	u64 diff2 = U64_MAX;
+
+	for (m = WZRD_M_MIN; m <= WZRD_M_MAX; m++) {
+		for (d = WZRD_D_MIN; d <= WZRD_D_MAX; d++) {
+			vco_freq = DIV_ROUND_CLOSEST((parent_rate * m), d);
+			if (vco_freq >= WZRD_VCO_MIN && vco_freq <= WZRD_VCO_MAX) {
+				for (o = WZRD_O_MIN; o <= WZRD_O_MAX; o++) {
+					freq = DIV_ROUND_CLOSEST(vco_freq, o);
+					diff = abs(freq - rate);
+
+					if (diff < WZRD_MIN_ERR) {
+						divider->valuem = m;
+						divider->valued = d;
+						divider->valueo = o;
+						diff2 = diff;
+						return 0;
+					}
+					if (diff < diff2) {
+						divider->valuem = m;
+						divider->valued = d;
+						divider->valueo = o;
+						diff2 = diff;
+					}
+				}
+			}
+		}
+	}
+	return -EBUSY;
+}
+
+static int clk_wzrd_dynamic_all_nolock(struct clk_hw *hw, unsigned long rate,
+				       unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	u32 reg, pre;
+	u32 value;
+	int err;
+	u64 vco_freq, rate_div, f, clockout0_div;
+
+	err = clk_wzrd_get_divisors(hw, rate, parent_rate);
+	if (err)
+		pr_err("failed to get divisors\n");
+
+	vco_freq = DIV_ROUND_CLOSEST((parent_rate * divider->valuem), divider->valued);
+	rate_div = DIV_ROUND_CLOSEST((vco_freq * WZRD_FRAC_POINTS), rate);
+
+	clockout0_div = rate_div / WZRD_FRAC_POINTS;
+
+	pre = DIV_ROUND_CLOSEST((vco_freq * WZRD_FRAC_POINTS), rate);
+	f = (u32)(pre - (clockout0_div * WZRD_FRAC_POINTS));
+	f = f & WZRD_CLKOUT_FRAC_MASK;
+
+	reg = FIELD_PREP(WZRD_CLKOUT_DIVIDE_MASK, clockout0_div) |
+	      FIELD_PREP(WZRD_CLKOUT0_FRAC_MASK, f);
+
+	writel(reg, divider->base + WZRD_CLK_CFG_REG(2));
+	/* Set divisor and clear phase offset */
+	reg = FIELD_PREP(WZRD_CLKFBOUT_MULT_MASK, divider->valuem) |
+	      FIELD_PREP(WZRD_DIVCLK_DIVIDE_MASK, divider->valued);
+	writel(reg, divider->base + WZRD_CLK_CFG_REG(0));
+	writel(divider->valueo, divider->base + WZRD_CLK_CFG_REG(2));
+	writel(0, divider->base + WZRD_CLK_CFG_REG(3));
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET, value,
+				 value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+	if (err)
+		return -ETIMEDOUT;
+
+	/* Initiate reconfiguration */
+	writel(WZRD_DR_BEGIN_DYNA_RECONF,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET, value,
+				 value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+	if (err)
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static int clk_wzrd_dynamic_all(struct clk_hw *hw, unsigned long rate,
+				unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	unsigned long flags = 0;
+	int ret;
+
+	if (divider->lock)
+		spin_lock_irqsave(divider->lock, flags);
+	else
+		__acquire(divider->lock);
+
+	ret = clk_wzrd_dynamic_all_nolock(hw, rate, parent_rate);
+
+	if (divider->lock)
+		spin_unlock_irqrestore(divider->lock, flags);
+	else
+		__release(divider->lock);
+
+	return ret;
+}
+
+static unsigned long clk_wzrd_recalc_rate_all(struct clk_hw *hw,
+					      unsigned long parent_rate)
+{
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	u32 m, d, o, div, reg, f;
+
+	reg = readl(divider->base + WZRD_CLK_CFG_REG(0));
+	d = FIELD_GET(WZRD_DIVCLK_DIVIDE_MASK, reg);
+	m = FIELD_GET(WZRD_CLKFBOUT_MULT_MASK, reg);
+	reg = readl(divider->base + WZRD_CLK_CFG_REG(2));
+	o = FIELD_GET(WZRD_DIVCLK_DIVIDE_MASK, reg);
+	f = FIELD_GET(WZRD_CLKOUT0_FRAC_MASK, reg);
+
+	div = DIV_ROUND_CLOSEST(d * (WZRD_FRAC_POINTS * o + f), WZRD_FRAC_POINTS);
+	return divider_recalc_rate(hw, parent_rate * m, div, divider->table,
+			divider->flags, divider->width);
+}
+
+static long clk_wzrd_round_rate_all(struct clk_hw *hw, unsigned long rate,
+				    unsigned long *prate)
+{
+	return rate;
+}
+
+static const struct clk_ops clk_wzrd_clk_divider_ops = {
+	.round_rate = clk_wzrd_round_rate,
+	.set_rate = clk_wzrd_dynamic_reconfig,
+	.recalc_rate = clk_wzrd_recalc_rate,
+};
+
+static const struct clk_ops clk_wzrd_clk_div_all_ops = {
+	.round_rate = clk_wzrd_round_rate_all,
+	.set_rate = clk_wzrd_dynamic_all,
+	.recalc_rate = clk_wzrd_recalc_rate_all,
+};
+
+static unsigned long clk_wzrd_recalc_ratef(struct clk_hw *hw,
+					   unsigned long parent_rate)
+{
+	unsigned int val;
+	u32 div, frac;
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	void __iomem *div_addr = divider->base + divider->offset;
+
+	val = readl(div_addr);
+	div = val & div_mask(divider->width);
+	frac = (val >> WZRD_CLKOUT_FRAC_SHIFT) & WZRD_CLKOUT_FRAC_MASK;
+
+	return mult_frac(parent_rate, 1000, (div * 1000) + frac);
+}
+
+static int clk_wzrd_dynamic_reconfig_f(struct clk_hw *hw, unsigned long rate,
+				       unsigned long parent_rate)
+{
+	int err = 0;
+	u32 value, pre;
+	unsigned long rate_div, f, clockout0_div;
+	struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+	void __iomem *div_addr = divider->base + divider->offset;
+
+	rate_div = DIV_ROUND_DOWN_ULL(parent_rate * 1000, rate);
+	clockout0_div = rate_div / 1000;
+
+	pre = DIV_ROUND_CLOSEST((parent_rate * 1000), rate);
+	f = (u32)(pre - (clockout0_div * 1000));
+	f = f & WZRD_CLKOUT_FRAC_MASK;
+	f = f << WZRD_CLKOUT_DIVIDE_WIDTH;
+
+	value = (f  | (clockout0_div & WZRD_CLKOUT_DIVIDE_MASK));
+
+	/* Set divisor and clear phase offset */
+	writel(value, div_addr);
+	writel(0x0, div_addr + WZRD_DR_DIV_TO_PHASE_OFFSET);
+
+	/* Check status register */
+	err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET, value,
+				 value & WZRD_DR_LOCK_BIT_MASK,
+				 WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+	if (err)
+		return err;
+
+	/* Initiate reconfiguration */
+	writel(WZRD_DR_BEGIN_DYNA_RECONF_5_2,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+	writel(WZRD_DR_BEGIN_DYNA_RECONF1_5_2,
+	       divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+	/* Check status register */
+	return readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET, value,
+				  value & WZRD_DR_LOCK_BIT_MASK,
+				  WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
+}
+
+static long clk_wzrd_round_rate_f(struct clk_hw *hw, unsigned long rate,
+				  unsigned long *prate)
+{
+	return rate;
+}
+
+static const struct clk_ops clk_wzrd_clk_divider_ops_f = {
+	.round_rate = clk_wzrd_round_rate_f,
+	.set_rate = clk_wzrd_dynamic_reconfig_f,
+	.recalc_rate = clk_wzrd_recalc_ratef,
+};
+
+static struct clk *clk_wzrd_register_divf(struct device *dev,
+					  const char *name,
+					  const char *parent_name,
+					  unsigned long flags,
+					  void __iomem *base, u16 offset,
+					  u8 shift, u8 width,
+					  u8 clk_divider_flags,
+					  u32 div_type,
+					  spinlock_t *lock)
+{
+	struct clk_wzrd_divider *div;
+	struct clk_hw *hw;
+	struct clk_init_data init;
+	int ret;
+
+	div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
+	if (!div)
+		return ERR_PTR(-ENOMEM);
+
+	init.name = name;
+
+	init.ops = &clk_wzrd_clk_divider_ops_f;
+
+	init.flags = flags;
+	init.parent_names = &parent_name;
+	init.num_parents = 1;
+
+	div->base = base;
+	div->offset = offset;
+	div->shift = shift;
+	div->width = width;
+	div->flags = clk_divider_flags;
+	div->lock = lock;
+	div->hw.init = &init;
+	div->table = NULL;
+
+	hw = &div->hw;
+	ret = devm_clk_hw_register(dev, hw);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return hw->clk;
+}
+
+static struct clk *clk_wzrd_register_divider(struct device *dev,
+					     const char *name,
+					     const char *parent_name,
+					     unsigned long flags,
+					     void __iomem *base, u16 offset,
+					     u8 shift, u8 width,
+					     u8 clk_divider_flags,
+					     u32 div_type,
+					     spinlock_t *lock)
+{
+	struct clk_wzrd_divider *div;
+	struct clk_hw *hw;
+	struct clk_init_data init;
+	int ret;
+
+	div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
+	if (!div)
+		return ERR_PTR(-ENOMEM);
+
+	init.name = name;
+	if (clk_divider_flags & CLK_DIVIDER_READ_ONLY)
+		init.ops = &clk_divider_ro_ops;
+	else if (div_type == DIV_O)
+		init.ops = &clk_wzrd_clk_divider_ops;
+	else
+		init.ops = &clk_wzrd_clk_div_all_ops;
+	init.flags = flags;
+	init.parent_names = &parent_name;
+	init.num_parents = 1;
+
+	div->base = base;
+	div->offset = offset;
+	div->shift = shift;
+	div->width = width;
+	div->flags = clk_divider_flags;
+	div->lock = lock;
+	div->hw.init = &init;
+	div->table = NULL;
+
+	hw = &div->hw;
+	ret = devm_clk_hw_register(dev, hw);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return hw->clk;
+}
+
+static int clk_wzrd_clk_notifier(struct notifier_block *nb, unsigned long event,
+				 void *data)
+{
+	unsigned long max;
+	struct clk_notifier_data *ndata = data;
+	struct clk_wzrd *clk_wzrd = to_clk_wzrd(nb);
+
+	if (clk_wzrd->suspended)
+		return NOTIFY_OK;
+
+	if (ndata->clk == clk_wzrd->clk_in1)
+		max = clk_wzrd_max_freq[clk_wzrd->speed_grade - 1];
+	else if (ndata->clk == clk_wzrd->axi_clk)
+		max = WZRD_ACLK_MAX_FREQ;
+	else
+		return NOTIFY_DONE;	/* should never happen */
+
+	switch (event) {
+	case PRE_RATE_CHANGE:
+		if (ndata->new_rate > max)
+			return NOTIFY_BAD;
+		return NOTIFY_OK;
+	case POST_RATE_CHANGE:
+	case ABORT_RATE_CHANGE:
+	default:
+		return NOTIFY_DONE;
+	}
+}
+
+static int __maybe_unused clk_wzrd_suspend(struct device *dev)
+{
+	struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(clk_wzrd->axi_clk);
+	clk_wzrd->suspended = true;
+
+	return 0;
+}
+
+static int __maybe_unused clk_wzrd_resume(struct device *dev)
+{
+	int ret;
+	struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
+
+	ret = clk_prepare_enable(clk_wzrd->axi_clk);
+	if (ret) {
+		dev_err(dev, "unable to enable s_axi_aclk\n");
+		return ret;
+	}
+
+	clk_wzrd->suspended = false;
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(clk_wzrd_dev_pm_ops, clk_wzrd_suspend,
+			 clk_wzrd_resume);
+
+static int clk_wzrd_probe(struct platform_device *pdev)
+{
+	int i, ret;
+	u32 reg, reg_f, mult;
+	unsigned long rate;
+	const char *clk_name;
+	void __iomem *ctrl_reg;
+	struct clk_wzrd *clk_wzrd;
+	int outputs;
+	unsigned long flags = 0;
+	const char *clkout_name;
+	struct device_node *np = pdev->dev.of_node;
+
+	clk_wzrd = devm_kzalloc(&pdev->dev, sizeof(*clk_wzrd), GFP_KERNEL);
+	if (!clk_wzrd)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, clk_wzrd);
+
+	clk_wzrd->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(clk_wzrd->base))
+		return PTR_ERR(clk_wzrd->base);
+
+	ret = of_property_read_u32(np, "xlnx,speed-grade", &clk_wzrd->speed_grade);
+	if (!ret) {
+		if (clk_wzrd->speed_grade < 1 || clk_wzrd->speed_grade > 3) {
+			dev_warn(&pdev->dev, "invalid speed grade '%d'\n",
+				 clk_wzrd->speed_grade);
+			clk_wzrd->speed_grade = 0;
+		}
+	}
+
+	clk_wzrd->clk_in1 = devm_clk_get(&pdev->dev, "clk_in1");
+	if (IS_ERR(clk_wzrd->clk_in1)) {
+		if (clk_wzrd->clk_in1 != ERR_PTR(-EPROBE_DEFER))
+			dev_err(&pdev->dev, "clk_in1 not found\n");
+		return PTR_ERR(clk_wzrd->clk_in1);
+	}
+
+	clk_wzrd->axi_clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+	if (IS_ERR(clk_wzrd->axi_clk)) {
+		if (clk_wzrd->axi_clk != ERR_PTR(-EPROBE_DEFER))
+			dev_err(&pdev->dev, "s_axi_aclk not found\n");
+		return PTR_ERR(clk_wzrd->axi_clk);
+	}
+	ret = clk_prepare_enable(clk_wzrd->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "enabling s_axi_aclk failed\n");
+		return ret;
+	}
+	rate = clk_get_rate(clk_wzrd->axi_clk);
+	if (rate > WZRD_ACLK_MAX_FREQ) {
+		dev_err(&pdev->dev, "s_axi_aclk frequency (%lu) too high\n",
+			rate);
+		ret = -EINVAL;
+		goto err_disable_clk;
+	}
+
+	outputs = of_property_count_strings(np, "clock-output-names");
+	clk_name = kasprintf(GFP_KERNEL, "%s_mul_div", dev_name(&pdev->dev));
+	if (!clk_name) {
+		ret = -ENOMEM;
+		goto err_rm_int_clk;
+	}
+
+	if (outputs == 1) {
+		if (of_property_read_string_index(np, "clock-output-names", 0,
+						  &clkout_name)) {
+			dev_err(&pdev->dev,
+				"clock output name not specified\n");
+			ret = -EINVAL;
+			goto err_rm_int_clks;
+		}
+
+		clk_wzrd->clkout[0] = clk_wzrd_register_divider
+				(&pdev->dev, clkout_name,
+				__clk_get_name(clk_wzrd->clk_in1), 0,
+				clk_wzrd->base, WZRD_CLK_CFG_REG(3),
+				WZRD_CLKOUT_DIVIDE_SHIFT,
+				WZRD_CLKOUT_DIVIDE_WIDTH,
+				CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+				DIV_ALL, &clkwzrd_lock);
+
+		goto out;
+	}
+
+	/* register multiplier */
+	reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
+		     WZRD_CLKFBOUT_MULT_MASK) >> WZRD_CLKFBOUT_MULT_SHIFT;
+	reg_f = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
+		     WZRD_CLKFBOUT_FRAC_MASK) >> WZRD_CLKFBOUT_FRAC_SHIFT;
+
+	mult = ((reg * 1000) + reg_f);
+	clk_name = kasprintf(GFP_KERNEL, "%s_mul", dev_name(&pdev->dev));
+	if (!clk_name) {
+		ret = -ENOMEM;
+		goto err_disable_clk;
+	}
+	clk_wzrd->clks_internal[wzrd_clk_mul] = clk_register_fixed_factor
+			(&pdev->dev, clk_name,
+			 __clk_get_name(clk_wzrd->clk_in1),
+			0, mult, 1000);
+	kfree(clk_name);
+	if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul])) {
+		dev_err(&pdev->dev, "unable to register fixed-factor clock\n");
+		ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul]);
+		goto err_disable_clk;
+	}
+
+	clk_name = kasprintf(GFP_KERNEL, "%s_mul_div", dev_name(&pdev->dev));
+	if (!clk_name) {
+		ret = -ENOMEM;
+		goto err_rm_int_clk;
+	}
+
+	ctrl_reg = clk_wzrd->base + WZRD_CLK_CFG_REG(0);
+	/* register div */
+	clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_divider
+			(&pdev->dev, clk_name,
+			 __clk_get_name(clk_wzrd->clks_internal[wzrd_clk_mul]),
+			flags, ctrl_reg, 0, 8, CLK_DIVIDER_ONE_BASED |
+			CLK_DIVIDER_ALLOW_ZERO, &clkwzrd_lock);
+	if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div])) {
+		dev_err(&pdev->dev, "unable to register divider clock\n");
+		ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div]);
+		goto out;
+	}
+
+	/* register div per output */
+	for (i = outputs - 1; i >= 0 ; i--) {
+		if (of_property_read_string_index(np, "clock-output-names", i,
+						  &clkout_name)) {
+			dev_err(&pdev->dev,
+				"clock output name not specified\n");
+			ret = -EINVAL;
+			goto err_rm_int_clks;
+		}
+		if (!i)
+			clk_wzrd->clkout[i] = clk_wzrd_register_divf
+				(&pdev->dev, clkout_name,
+				clk_name, flags,
+				clk_wzrd->base, (WZRD_CLK_CFG_REG(2) + i * 12),
+				WZRD_CLKOUT_DIVIDE_SHIFT,
+				WZRD_CLKOUT_DIVIDE_WIDTH,
+				CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+				DIV_O, &clkwzrd_lock);
+		else
+			clk_wzrd->clkout[i] = clk_wzrd_register_divider
+				(&pdev->dev, clkout_name,
+				clk_name, 0,
+				clk_wzrd->base, (WZRD_CLK_CFG_REG(2) + i * 12),
+				WZRD_CLKOUT_DIVIDE_SHIFT,
+				WZRD_CLKOUT_DIVIDE_WIDTH,
+				CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+				DIV_O, &clkwzrd_lock);
+		if (IS_ERR(clk_wzrd->clkout[i])) {
+			int j;
+
+			for (j = i + 1; j < outputs; j++)
+				clk_unregister(clk_wzrd->clkout[j]);
+			dev_err(&pdev->dev,
+				"unable to register divider clock\n");
+			ret = PTR_ERR(clk_wzrd->clkout[i]);
+			goto err_rm_int_clks;
+		}
+	}
+
+	kfree(clk_name);
+out:
+	clk_wzrd->clk_data.clks = clk_wzrd->clkout;
+	clk_wzrd->clk_data.clk_num = ARRAY_SIZE(clk_wzrd->clkout);
+	of_clk_add_provider(np, of_clk_src_onecell_get, &clk_wzrd->clk_data);
+
+	if (clk_wzrd->speed_grade) {
+		clk_wzrd->nb.notifier_call = clk_wzrd_clk_notifier;
+
+		ret = clk_notifier_register(clk_wzrd->clk_in1,
+					    &clk_wzrd->nb);
+		if (ret)
+			dev_warn(&pdev->dev,
+				 "unable to register clock notifier\n");
+
+		ret = clk_notifier_register(clk_wzrd->axi_clk, &clk_wzrd->nb);
+		if (ret)
+			dev_warn(&pdev->dev,
+				 "unable to register clock notifier\n");
+	}
+
+	return 0;
+
+err_rm_int_clks:
+	clk_unregister(clk_wzrd->clks_internal[1]);
+err_rm_int_clk:
+	kfree(clk_name);
+	clk_unregister(clk_wzrd->clks_internal[0]);
+err_disable_clk:
+	clk_disable_unprepare(clk_wzrd->axi_clk);
+
+	return ret;
+}
+
+static int clk_wzrd_remove(struct platform_device *pdev)
+{
+	int i;
+	struct clk_wzrd *clk_wzrd = platform_get_drvdata(pdev);
+
+	of_clk_del_provider(pdev->dev.of_node);
+
+	for (i = 0; i < WZRD_NUM_OUTPUTS; i++)
+		clk_unregister(clk_wzrd->clkout[i]);
+	for (i = 0; i < wzrd_clk_int_max; i++)
+		clk_unregister(clk_wzrd->clks_internal[i]);
+
+	if (clk_wzrd->speed_grade) {
+		clk_notifier_unregister(clk_wzrd->axi_clk, &clk_wzrd->nb);
+		clk_notifier_unregister(clk_wzrd->clk_in1, &clk_wzrd->nb);
+	}
+
+	clk_disable_unprepare(clk_wzrd->axi_clk);
+
+	return 0;
+}
+
+static const struct of_device_id clk_wzrd_ids[] = {
+	{ .compatible = "xlnx,clocking-wizard" },
+	{ .compatible = "xlnx,clocking-wizard-v5.2" },
+	{ .compatible = "xlnx,clocking-wizard-v6.0" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, clk_wzrd_ids);
+
+static struct platform_driver clk_wzrd_driver = {
+	.driver = {
+		.name = "clk-wizard",
+		.of_match_table = clk_wzrd_ids,
+		.pm = &clk_wzrd_dev_pm_ops,
+	},
+	.probe = clk_wzrd_probe,
+	.remove = clk_wzrd_remove,
+};
+module_platform_driver(clk_wzrd_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Soeren Brinkmann <soren.brinkmann@xilinx.com");
+MODULE_DESCRIPTION("Driver for the Xilinx Clocking Wizard IP core");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/clk.c
@@ -37,7 +37,11 @@
 static HLIST_HEAD(clk_orphan_list);
 static LIST_HEAD(clk_notifier_list);
 
-static struct hlist_head *all_lists[] = {
+/* List of registered clks that use runtime PM */
+static HLIST_HEAD(clk_rpm_list);
+static DEFINE_MUTEX(clk_rpm_list_lock);
+
+static const struct hlist_head *all_lists[] = {
 	&clk_root_list,
 	&clk_orphan_list,
 	NULL,
@@ -59,6 +63,7 @@
 	struct clk_hw		*hw;
 	struct module		*owner;
 	struct device		*dev;
+	struct hlist_node	rpm_node;
 	struct device_node	*of_node;
 	struct clk_core		*parent;
 	struct clk_parent_map	*parents;
@@ -129,6 +134,89 @@
 	pm_runtime_put_sync(core->dev);
 }
 
+/**
+ * clk_pm_runtime_get_all() - Runtime "get" all clk provider devices
+ *
+ * Call clk_pm_runtime_get() on all runtime PM enabled clks in the clk tree so
+ * that disabling unused clks avoids a deadlock where a device is runtime PM
+ * resuming/suspending and the runtime PM callback is trying to grab the
+ * prepare_lock for something like clk_prepare_enable() while
+ * clk_disable_unused_subtree() holds the prepare_lock and is trying to runtime
+ * PM resume/suspend the device as well.
+ *
+ * Context: Acquires the 'clk_rpm_list_lock' and returns with the lock held on
+ * success. Otherwise the lock is released on failure.
+ *
+ * Return: 0 on success, negative errno otherwise.
+ */
+static int clk_pm_runtime_get_all(void)
+{
+	int ret;
+	struct clk_core *core, *failed;
+
+	/*
+	 * Grab the list lock to prevent any new clks from being registered
+	 * or unregistered until clk_pm_runtime_put_all().
+	 */
+	mutex_lock(&clk_rpm_list_lock);
+
+	/*
+	 * Runtime PM "get" all the devices that are needed for the clks
+	 * currently registered. Do this without holding the prepare_lock, to
+	 * avoid the deadlock.
+	 */
+	hlist_for_each_entry(core, &clk_rpm_list, rpm_node) {
+		ret = clk_pm_runtime_get(core);
+		if (ret) {
+			failed = core;
+			pr_err("clk: Failed to runtime PM get '%s' for clk '%s'\n",
+			       dev_name(failed->dev), failed->name);
+			goto err;
+		}
+	}
+
+	return 0;
+
+err:
+	hlist_for_each_entry(core, &clk_rpm_list, rpm_node) {
+		if (core == failed)
+			break;
+
+		clk_pm_runtime_put(core);
+	}
+	mutex_unlock(&clk_rpm_list_lock);
+
+	return ret;
+}
+
+/**
+ * clk_pm_runtime_put_all() - Runtime "put" all clk provider devices
+ *
+ * Put the runtime PM references taken in clk_pm_runtime_get_all() and release
+ * the 'clk_rpm_list_lock'.
+ */
+static void clk_pm_runtime_put_all(void)
+{
+	struct clk_core *core;
+
+	hlist_for_each_entry(core, &clk_rpm_list, rpm_node)
+		clk_pm_runtime_put(core);
+	mutex_unlock(&clk_rpm_list_lock);
+}
+
+static void clk_pm_runtime_init(struct clk_core *core)
+{
+	struct device *dev = core->dev;
+
+	if (dev && pm_runtime_enabled(dev)) {
+		core->rpm_enabled = true;
+
+		mutex_lock(&clk_rpm_list_lock);
+		hlist_add_head(&core->rpm_node, &clk_rpm_list);
+		mutex_unlock(&clk_rpm_list_lock);
+	}
+}
+
 /***           locking             ***/
 static void clk_prepare_lock(void)
 {
@@ -251,6 +339,17 @@
 		}
 	}
 
+	/*
+	 * This could be called with the enable lock held, or from atomic
+	 * context. If the parent isn't enabled already, we can't do
+	 * anything here. We can also assume this clock isn't enabled.
+	 */
+	if ((core->flags & CLK_OPS_PARENT_ENABLE) && core->parent)
+		if (!clk_core_is_enabled(core->parent)) {
+			ret = false;
+			goto done;
+		}
+
 	ret = core->ops->is_enabled(core->hw);
 done:
 	if (core->rpm_enabled)
@@ -414,6 +513,9 @@
 	if (IS_ERR(hw))
 		return ERR_CAST(hw);
 
+	if (!hw)
+		return NULL;
+
 	return hw->core;
 }
 
@@ -631,6 +733,24 @@
 		*max_rate = min(*max_rate, clk_user->max_rate);
 }
 
+static bool clk_core_check_boundaries(struct clk_core *core,
+				      unsigned long min_rate,
+				      unsigned long max_rate)
+{
+	struct clk *user;
+
+	lockdep_assert_held(&prepare_lock);
+
+	if (min_rate > core->max_rate || max_rate < core->min_rate)
+		return false;
+
+	hlist_for_each_entry(user, &core->clks, clks_node)
+		if (min_rate > user->max_rate || max_rate < user->min_rate)
+			return false;
+
+	return true;
+}
+
 void clk_hw_set_rate_range(struct clk_hw *hw, unsigned long min_rate,
 			   unsigned long max_rate)
 {
@@ -800,6 +920,25 @@
 }
 EXPORT_SYMBOL_GPL(clk_rate_exclusive_get);
 
+static void devm_clk_rate_exclusive_put(void *data)
+{
+	struct clk *clk = data;
+
+	clk_rate_exclusive_put(clk);
+}
+
+int devm_clk_rate_exclusive_get(struct device *dev, struct clk *clk)
+{
+	int ret;
+
+	ret = clk_rate_exclusive_get(clk);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, devm_clk_rate_exclusive_put, clk);
+}
+EXPORT_SYMBOL_GPL(devm_clk_rate_exclusive_get);
+
 static void clk_core_unprepare(struct clk_core *core)
 {
 	lockdep_assert_held(&prepare_lock);
@@ -828,10 +967,9 @@
 	if (core->ops->unprepare)
 		core->ops->unprepare(core->hw);
 
-	clk_pm_runtime_put(core);
-
 	trace_clk_unprepare_complete(core);
 	clk_core_unprepare(core->parent);
+	clk_pm_runtime_put(core);
 }
 
 static void clk_core_unprepare_lock(struct clk_core *core)
@@ -1221,9 +1359,6 @@
 	if (core->flags & CLK_IGNORE_UNUSED)
 		return;
 
-	if (clk_pm_runtime_get(core))
-		return;
-
 	if (clk_core_is_prepared(core)) {
 		trace_clk_unprepare(core);
 		if (core->ops->unprepare_unused)
@@ -1232,8 +1367,6 @@
 			core->ops->unprepare(core->hw);
 		trace_clk_unprepare_complete(core);
 	}
-
-	clk_pm_runtime_put(core);
 }
 
 static void __init clk_disable_unused_subtree(struct clk_core *core)
@@ -1249,9 +1382,6 @@
 	if (core->flags & CLK_OPS_PARENT_ENABLE)
 		clk_core_prepare_enable(core->parent);
 
-	if (clk_pm_runtime_get(core))
-		goto unprepare_out;
-
 	flags = clk_enable_lock();
 
 	if (core->enable_count)
@@ -1276,8 +1406,6 @@
 
 unlock_out:
 	clk_enable_unlock(flags);
-	clk_pm_runtime_put(core);
-unprepare_out:
 	if (core->flags & CLK_OPS_PARENT_ENABLE)
 		clk_core_disable_unprepare(core->parent);
 }
@@ -1293,12 +1421,22 @@
 static int __init clk_disable_unused(void)
 {
 	struct clk_core *core;
+	int ret;
 
 	if (clk_ignore_unused) {
 		pr_warn("clk: Not disabling unused clocks\n");
 		return 0;
 	}
 
+	pr_info("clk: Disabling unused clocks\n");
+
+	ret = clk_pm_runtime_get_all();
+	if (ret)
+		return ret;
+	/*
+	 * Grab the prepare lock to keep the clk topology stable while iterating
+	 * over clks.
+	 */
 	clk_prepare_lock();
 
 	hlist_for_each_entry(core, &clk_root_list, child_node)
@@ -1315,6 +1453,8 @@
 
 	clk_prepare_unlock();
 
+	clk_pm_runtime_put_all();
+
 	return 0;
 }
 late_initcall_sync(clk_disable_unused);
@@ -2347,6 +2487,11 @@
 	clk->min_rate = min;
 	clk->max_rate = max;
 
+	if (!clk_core_check_boundaries(clk->core, min, max)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	rate = clk_core_get_rate_nolock(clk->core);
 	if (rate < min || rate > max) {
 		/*
@@ -2375,6 +2520,7 @@
 		}
 	}
 
+out:
 	if (clk->exclusive_count)
 		clk_core_rate_protect(clk->core);
 
@@ -3159,6 +3305,7 @@
 				 unsigned int i, char terminator)
 {
 	struct clk_core *parent;
+	const char *name = NULL;
 
 	/*
 	 * Go through the following options to fetch a parent's name.
@@ -3173,18 +3320,20 @@
 	 * registered (yet).
 	 */
 	parent = clk_core_get_parent_by_index(core, i);
-	if (parent)
+	if (parent) {
 		seq_puts(s, parent->name);
-	else if (core->parents[i].name)
+	} else if (core->parents[i].name) {
 		seq_puts(s, core->parents[i].name);
-	else if (core->parents[i].fw_name)
+	} else if (core->parents[i].fw_name) {
 		seq_printf(s, "<%s>(fw)", core->parents[i].fw_name);
-	else if (core->parents[i].index >= 0)
-		seq_puts(s,
-			 of_clk_get_parent_name(core->of_node,
-						core->parents[i].index));
-	else
-		seq_puts(s, "(missing)");
+	} else {
+		if (core->parents[i].index >= 0)
+			name = of_clk_get_parent_name(core->of_node, core->parents[i].index);
+		if (!name)
+			name = "(missing)";
+
+		seq_puts(s, name);
+	}
 
 	seq_putc(s, terminator);
 }
@@ -3340,6 +3489,24 @@
 {
 	struct clk_core *core;
 
+#ifdef CLOCK_ALLOW_WRITE_DEBUGFS
+	pr_warn("\n");
+	pr_warn("********************************************************************\n");
+	pr_warn("**     NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE           **\n");
+	pr_warn("**                                                                **\n");
+	pr_warn("**  WRITEABLE clk DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL **\n");
+	pr_warn("**                                                                **\n");
+	pr_warn("** This means that this kernel is built to expose clk operations  **\n");
+	pr_warn("** such as parent or rate setting, enabling, disabling, etc.      **\n");
+	pr_warn("** to userspace, which may compromise security on your system.    **\n");
+	pr_warn("**                                                                **\n");
+	pr_warn("** If you see this message and you are not debugging the          **\n");
+	pr_warn("** kernel, report this immediately to your vendor!                **\n");
+	pr_warn("**                                                                **\n");
+	pr_warn("**     NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE           **\n");
+	pr_warn("********************************************************************\n");
+#endif
+
 	rootdir = debugfs_create_dir("clk", NULL);
 
 	debugfs_create_file("clk_summary", 0444, rootdir, &all_lists,
@@ -3392,6 +3559,19 @@
 			__clk_set_parent_after(orphan, parent, NULL);
 			__clk_recalc_accuracies(orphan);
 			__clk_recalc_rates(orphan, 0);
+
+			/*
+			 * __clk_init_parent() will set the initial req_rate to
+			 * 0 if the clock doesn't have clk_ops::recalc_rate and
+			 * is an orphan when it's registered.
+			 *
+			 * 'req_rate' is used by clk_set_rate_range() and
+			 * clk_put() to trigger a clk_set_rate() call whenever
+			 * the boundaries are modified. Let's make sure
+			 * 'req_rate' is set to something non-zero so that
+			 * clk_set_rate_range() doesn't drop the frequency.
+			 */
+			orphan->req_rate = orphan->rate;
 		}
 	}
 }
@@ -3415,6 +3595,14 @@
 
 	clk_prepare_lock();
 
+	/*
+	 * Set hw->core after grabbing the prepare_lock to synchronize with
+	 * callers of clk_core_fill_parent_index() where we treat hw->core
+	 * being NULL as the clk not being registered yet. This is crucial so
+	 * that clks aren't parented until their parent is fully registered.
+	 */
+	core->hw->core = core;
+
 	ret = clk_pm_runtime_get(core);
 	if (ret)
 		goto unlock;
@@ -3573,14 +3761,13 @@
 	}
 
 	clk_core_reparent_orphans_nolock();
-
-
-	kref_init(&core->ref);
 out:
 	clk_pm_runtime_put(core);
 unlock:
-	if (ret)
+	if (ret) {
 		hlist_del_init(&core->child_node);
+		core->hw->core = NULL;
+	}
 
 	clk_prepare_unlock();
 
@@ -3702,8 +3889,9 @@
 struct clk *clk_hw_get_clk(struct clk_hw *hw, const char *con_id)
 {
 	struct device *dev = hw->core->dev;
+	const char *name = dev ? dev_name(dev) : NULL;
 
-	return clk_hw_create_clk(dev, hw, dev_name(dev), con_id);
+	return clk_hw_create_clk(dev, hw, name, con_id);
 }
 EXPORT_SYMBOL(clk_hw_get_clk);
 
@@ -3801,6 +3989,22 @@
 	kfree(core->parents);
 }
 
+/* Free memory allocated for a struct clk_core */
+static void __clk_release(struct kref *ref)
+{
+	struct clk_core *core = container_of(ref, struct clk_core, ref);
+
+	if (core->rpm_enabled) {
+		mutex_lock(&clk_rpm_list_lock);
+		hlist_del(&core->rpm_node);
+		mutex_unlock(&clk_rpm_list_lock);
+	}
+
+	clk_core_free_parent_map(core);
+	kfree_const(core->name);
+	kfree(core);
+}
+
 static struct clk *
 __clk_register(struct device *dev, struct device_node *np, struct clk_hw *hw)
 {
@@ -3821,6 +4025,8 @@
 		goto fail_out;
 	}
 
+	kref_init(&core->ref);
+
 	core->name = kstrdup_const(init->name, GFP_KERNEL);
 	if (!core->name) {
 		ret = -ENOMEM;
@@ -3833,9 +4039,8 @@
 	}
 	core->ops = init->ops;
 
-	if (dev && pm_runtime_enabled(dev))
-		core->rpm_enabled = true;
 	core->dev = dev;
+	clk_pm_runtime_init(core);
 	core->of_node = np;
 	if (dev && dev->driver)
 		core->owner = dev->driver->owner;
@@ -3844,7 +4049,6 @@
 	core->num_parents = init->num_parents;
 	core->min_rate = 0;
 	core->max_rate = ULONG_MAX;
-	hw->core = core;
 
 	ret = clk_core_populate_parent_map(core, init);
 	if (ret)
@@ -3862,7 +4066,7 @@
 		goto fail_create_clk;
 	}
 
-	clk_core_link_consumer(hw->core, hw->clk);
+	clk_core_link_consumer(core, hw->clk);
 
 	ret = __clk_core_init(core);
 	if (!ret)
@@ -3876,12 +4080,10 @@
 	hw->clk = NULL;
 
 fail_create_clk:
-	clk_core_free_parent_map(core);
 fail_parents:
 fail_ops:
-	kfree_const(core->name);
 fail_name:
-	kfree(core);
+	kref_put(&core->ref, __clk_release);
 fail_out:
 	return ERR_PTR(ret);
 }
@@ -3961,18 +4163,6 @@
 }
 EXPORT_SYMBOL_GPL(of_clk_hw_register);
 
-/* Free memory allocated for a clock. */
-static void __clk_release(struct kref *ref)
-{
-	struct clk_core *core = container_of(ref, struct clk_core, ref);
-
-	lockdep_assert_held(&prepare_lock);
-
-	clk_core_free_parent_map(core);
-	kfree_const(core->name);
-	kfree(core);
-}
-
 /*
  * Empty clk_ops for unregistered clocks. These are used temporarily
  * after clk_unregister() was called on a clock and until last clock
@@ -4025,7 +4215,7 @@
 /* Remove this clk from all parent caches */
 static void clk_core_evict_parent_cache(struct clk_core *core)
 {
-	struct hlist_head **lists;
+	const struct hlist_head **lists;
 	struct clk_core *root;
 
 	lockdep_assert_held(&prepare_lock);
@@ -4056,7 +4246,8 @@
 	if (ops == &clk_nodrv_ops) {
 		pr_err("%s: unregistered clock: %s\n", __func__,
 		       clk->core->name);
-		goto unlock;
+		clk_prepare_unlock();
+		return;
 	}
 	/*
 	 * Assign empty clock ops for consumers that might still hold
@@ -4090,11 +4281,10 @@
 	if (clk->core->protect_count)
 		pr_warn("%s: unregistering protected clock: %s\n",
 					__func__, clk->core->name);
+	clk_prepare_unlock();
 
 	kref_put(&clk->core->ref, __clk_release);
 	free_clk(clk);
-unlock:
-	clk_prepare_unlock();
 }
 EXPORT_SYMBOL_GPL(clk_unregister);
 
@@ -4300,13 +4490,11 @@
 	    clk->max_rate < clk->core->req_rate)
 		clk_core_set_rate_nolock(clk->core, clk->core->req_rate);
 
-	owner = clk->core->owner;
-	kref_put(&clk->core->ref, __clk_release);
-
 	clk_prepare_unlock();
 
+	owner = clk->core->owner;
+	kref_put(&clk->core->ref, __clk_release);
 	module_put(owner);
-
 	free_clk(clk);
 }
 
@@ -4440,6 +4628,7 @@
 	if (!ret) {
 		devres->clk = clk;
 		devres->nb = nb;
+		devres_add(dev, devres);
 	} else {
 		devres_free(devres);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/davinci/da8xx-cfgchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/davinci/da8xx-cfgchip.c
@@ -505,7 +505,7 @@
 	const char * const parent_names[] = { "usb_refclkin", "pll0_auxclk" };
 	struct clk *fck_clk;
 	struct da8xx_usb0_clk48 *usb0;
-	struct clk_init_data init;
+	struct clk_init_data init = {};
 	int ret;
 
 	fck_clk = devm_clk_get(dev, "fck");
@@ -580,7 +580,7 @@
 {
 	const char * const parent_names[] = { "usb0_clk48", "usb_refclkin" };
 	struct da8xx_usb1_clk48 *usb1;
-	struct clk_init_data init;
+	struct clk_init_data init = {};
 	int ret;
 
 	usb1 = devm_kzalloc(dev, sizeof(*usb1), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/hisilicon/clk-hi3519.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/hisilicon/clk-hi3519.c
@@ -130,7 +130,7 @@
 	of_clk_del_provider(pdev->dev.of_node);
 
 	hisi_clk_unregister_gate(hi3519_gate_clks,
-				ARRAY_SIZE(hi3519_mux_clks),
+				ARRAY_SIZE(hi3519_gate_clks),
 				crg->clk_data);
 	hisi_clk_unregister_mux(hi3519_mux_clks,
 				ARRAY_SIZE(hi3519_mux_clks),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/hisilicon/clk-hi3559a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/hisilicon/clk-hi3559a.c
@@ -491,7 +491,6 @@
 
 		clk = clk_register(NULL, &p_clk->hw);
 		if (IS_ERR(clk)) {
-			devm_kfree(dev, p_clk);
 			dev_err(dev, "%s: failed to register clock %s\n",
 			       __func__, clks[i].name);
 			continue;
@@ -611,8 +610,8 @@
 
 
 /* shub div clk */
-static struct clk_div_table shub_spi_clk_table[] = {{0, 8}, {1, 4}, {2, 2}};
-static struct clk_div_table shub_uart_div_clk_table[] = {{1, 8}, {2, 4}};
+static struct clk_div_table shub_spi_clk_table[] = {{0, 8}, {1, 4}, {2, 2}, {/*sentinel*/}};
+static struct clk_div_table shub_uart_div_clk_table[] = {{1, 8}, {2, 4}, {/*sentinel*/}};
 
 static struct hisi_divider_clock hi3559av100_shub_div_clks[] = {
 	{ HI3559AV100_SHUB_SPI_SOURCE_CLK, "clk_spi_clk", "shub_clk", 0, 0x20, 24, 2,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/hisilicon/clk-hi3620.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/hisilicon/clk-hi3620.c
@@ -467,8 +467,10 @@
 		return;
 
 	clk_data->clks = kcalloc(num, sizeof(*clk_data->clks), GFP_KERNEL);
-	if (!clk_data->clks)
+	if (!clk_data->clks) {
+		kfree(clk_data);
 		return;
+	}
 
 	for (i = 0; i < num; i++) {
 		struct hisi_mmc_clock *mmc_clk = &hi3620_mmc_clks[i];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/idt/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/idt/Makefile
@@ -0,0 +1,3 @@
+obj-y += clk-idt8t49n24x-core.o
+obj-y += clk-idt8t49n24x-debugfs.o
+obj-y += clk-idt8t49n24x.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/idt/clk-idt8t49n24x-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/idt/clk-idt8t49n24x-core.c
@@ -0,0 +1,933 @@
+// SPDX-License-Identifier: GPL-2.0
+/* clk-idt8t49n24x-core.c - Program 8T49N24x settings via I2C (common code)
+ *
+ * Copyright (C) 2018, Integrated Device Technology, Inc. <david.cater@idt.com>
+ *
+ * See https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
+ * This program is distributed "AS IS" and  WITHOUT ANY WARRANTY;
+ * including the implied warranties of MERCHANTABILITY, FITNESS FOR
+ * A PARTICULAR PURPOSE, or NON-INFRINGEMENT.
+ */
+
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+
+#include "clk-idt8t49n24x-core.h"
+
+/*
+ * In Timing Commander, Q0 is changed from 25MHz to Q0 75MHz, the following
+ * changes occur:
+ *
+ * 2 bytes change in EEPROM data string.
+ *
+ * DSM_INT R0025[0],R0026[7:0] : 35 => 30
+ * NS2_Q0 R0040[7:0],R0041[7:0] : 14 => 4
+ *
+ * In EEPROM
+ * 1. R0026
+ * 2. R0041
+ *
+ * Note that VCO_Frequency (metadata) also changed (3500 =>3000).
+ * This reflects a change to DSM_INT.
+ *
+ * Note that the Timing Commander code has workarounds in the workflow scripts
+ * to handle dividers for the 8T49N241 (because the development of that GUI
+ * predates chip override functionality). That affects NS1_Qx (x in 1-3)
+ * and NS2_Qx. NS1_Qx contains the upper bits of NS_Qx, and NS2_Qx contains
+ * the lower bits. That is NOT the case for Q0, though. In that case NS1_Q0
+ * is the 1st stage output divider (/5, /6, /4) and NS2_Q0 is the 16-bit
+ * second stage (with actual divide being twice the value stored in the
+ * register).
+ *
+ * NS1_Q0 R003F[1:0]
+ */
+
+#define IDT24x_VCO_MIN			2999997000u
+#define IDT24x_VCO_MAX			4000004000u
+#define IDT24x_VCO_OPT			3500000000u
+#define IDT24x_MIN_INT_DIVIDER		6
+#define IDT24x_MIN_NS1			4
+#define IDT24x_MAX_NS1			6
+
+static u8 q0_ns1_options[3] = { 5, 6, 4 };
+
+/**
+ * bits_to_shift - num bits to shift given specified mask
+ * @mask:	32-bit word input to count zero bits on right
+ *
+ * Given a bit mask indicating where a value will be stored in
+ * a register, return the number of bits you need to shift the value
+ * before ORing it into the register value.
+ *
+ * Return: number of bits to shift
+ */
+int bits_to_shift(unsigned int mask)
+{
+	/* the number of zero bits on the right */
+	unsigned int c = 32;
+
+	mask &= ~mask + 1;
+	if (mask)
+		c--;
+	if (mask & 0x0000FFFF)
+		c -= 16;
+	if (mask & 0x00FF00FF)
+		c -= 8;
+	if (mask & 0x0F0F0F0F)
+		c -= 4;
+	if (mask & 0x33333333)
+		c -= 2;
+	if (mask & 0x55555555)
+		c -= 1;
+	return c;
+}
+
+/*
+ * TODO: Consider replacing this with regmap_multi_reg_write, which
+ * supports introducing a delay after each write. Experiment to see if
+ * the writes succeed consistently when using that API.
+ */
+static int regmap_bulk_write_with_retry(
+	struct regmap *map, unsigned int offset, u8 val[],
+	int val_count, int max_attempts)
+{
+	int err = 0;
+	int count = 1;
+
+	do {
+		err = regmap_bulk_write(map, offset, val, val_count);
+		if (err == 0)
+			return 0;
+
+		usleep_range(100, 200);
+	} while (count++ <= max_attempts);
+	return err;
+}
+
+static int regmap_write_with_retry(
+	struct regmap *map, unsigned int offset, unsigned int val,
+	int max_attempts)
+{
+	int err = 0;
+	int count = 1;
+
+	do {
+		err = regmap_write(map, offset, val);
+		if (err == 0)
+			return 0;
+		usleep_range(100, 200);
+	} while (count++ <= max_attempts);
+	return err;
+}
+
+/*
+ * TODO: Consider using regmap_multi_reg_write instead. Explore
+ * use of regmap to configure WRITE_BLOCK_SIZE, and using the delay
+ * mechanism in regmap_multi_reg_write instead of retrying multiple
+ * times (regmap_bulk_write_with_retry).
+ */
+int i2cwritebulk(
+	struct i2c_client *client, struct regmap *map,
+	unsigned int reg, u8 val[], size_t val_count)
+{
+	char dbg[128];
+	u8 block[WRITE_BLOCK_SIZE];
+	unsigned int block_offset = reg;
+	int x;
+	int err = 0;
+	int currentOffset = 0;
+
+	dev_dbg(&client->dev, "I2C->0x%04x : [hex] . First byte: %02x, Second byte: %02x",
+		reg, reg >> 8, reg & 0xFF);
+	dbg[0] = 0;
+
+	for (x = 0; x < val_count; x++) {
+		char data[4];
+
+		block[currentOffset++] = val[x];
+		sprintf(data, "%02x ", val[x]);
+		strcat(dbg, data);
+		if (x > 0 && (x + 1) % WRITE_BLOCK_SIZE == 0) {
+			dev_dbg(&client->dev, "%s", dbg);
+			dbg[0] = '\0';
+			sprintf(dbg,
+				"(loop) calling regmap_bulk_write @ 0x%04x [%d bytes]",
+				block_offset, WRITE_BLOCK_SIZE);
+			dev_dbg(&client->dev, "%s", dbg);
+			dbg[0] = '\0';
+			err = regmap_bulk_write_with_retry(
+				map, block_offset, block, WRITE_BLOCK_SIZE, 5);
+			if (err != 0)
+				break;
+			block_offset += WRITE_BLOCK_SIZE;
+			currentOffset = 0;
+		}
+	}
+	if (err == 0 && currentOffset > 0) {
+		dev_dbg(&client->dev, "%s", dbg);
+		dev_dbg(&client->dev, "(final) calling regmap_bulk_write @ 0x%04x [%d bytes]",
+			block_offset, currentOffset);
+		err = regmap_bulk_write_with_retry(
+			map, block_offset, block, currentOffset, 5);
+	}
+
+	return err;
+}
+
+static int i2cwrite(
+	struct i2c_client *client, struct regmap *map,
+	unsigned int reg, unsigned int val)
+{
+	int err;
+
+	dev_dbg(&client->dev, "I2C->0x%x : [hex] %x", reg, val);
+	err = regmap_write_with_retry(map, reg, val, 5);
+	usleep_range(100, 200);
+	return err;
+}
+
+static int i2cwritewithmask(
+	struct i2c_client *client, struct regmap *map, unsigned int reg,
+	u8 val, u8 original, u8 mask)
+{
+	return i2cwrite(client, map, reg,
+		((val << bits_to_shift(mask)) & mask) | (original & ~mask));
+}
+
+int idt24x_get_offsets(
+	u8 output_num,
+	struct clk_register_offsets *offsets)
+{
+	switch (output_num) {
+	case 0:
+		offsets->oe_offset = IDT24x_REG_OUTEN;
+		offsets->oe_mask = IDT24x_REG_OUTEN0_MASK;
+		offsets->dis_mask = IDT24x_REG_Q0_DIS_MASK;
+		offsets->ns1_offset = IDT24x_REG_NS1_Q0;
+		offsets->ns1_offset_mask = IDT24x_REG_NS1_Q0_MASK;
+		offsets->ns2_15_8_offset = IDT24x_REG_NS2_Q0_15_8;
+		offsets->ns2_7_0_offset = IDT24x_REG_NS2_Q0_7_0;
+		break;
+	case 1:
+		offsets->oe_offset = IDT24x_REG_OUTEN;
+		offsets->oe_mask = IDT24x_REG_OUTEN1_MASK;
+		offsets->dis_mask = IDT24x_REG_Q1_DIS_MASK;
+		offsets->n_17_16_offset = IDT24x_REG_N_Q1_17_16;
+		offsets->n_17_16_mask = IDT24x_REG_N_Q1_17_16_MASK;
+		offsets->n_15_8_offset = IDT24x_REG_N_Q1_15_8;
+		offsets->n_7_0_offset = IDT24x_REG_N_Q1_7_0;
+		offsets->nfrac_27_24_offset = IDT24x_REG_NFRAC_Q1_27_24;
+		offsets->nfrac_27_24_mask =
+			IDT24x_REG_NFRAC_Q1_27_24_MASK;
+		offsets->nfrac_23_16_offset = IDT24x_REG_NFRAC_Q1_23_16;
+		offsets->nfrac_15_8_offset = IDT24x_REG_NFRAC_Q1_15_8;
+		offsets->nfrac_7_0_offset = IDT24x_REG_NFRAC_Q1_7_0;
+		break;
+	case 2:
+		offsets->oe_offset = IDT24x_REG_OUTEN;
+		offsets->oe_mask = IDT24x_REG_OUTEN2_MASK;
+		offsets->dis_mask = IDT24x_REG_Q2_DIS_MASK;
+		offsets->n_17_16_offset = IDT24x_REG_N_Q2_17_16;
+		offsets->n_17_16_mask = IDT24x_REG_N_Q2_17_16_MASK;
+		offsets->n_15_8_offset = IDT24x_REG_N_Q2_15_8;
+		offsets->n_7_0_offset = IDT24x_REG_N_Q2_7_0;
+		offsets->nfrac_27_24_offset = IDT24x_REG_NFRAC_Q2_27_24;
+		offsets->nfrac_27_24_mask =
+			IDT24x_REG_NFRAC_Q2_27_24_MASK;
+		offsets->nfrac_23_16_offset = IDT24x_REG_NFRAC_Q2_23_16;
+		offsets->nfrac_15_8_offset = IDT24x_REG_NFRAC_Q2_15_8;
+		offsets->nfrac_7_0_offset = IDT24x_REG_NFRAC_Q2_7_0;
+		break;
+	case 3:
+		offsets->oe_offset = IDT24x_REG_OUTEN;
+		offsets->oe_mask = IDT24x_REG_OUTEN3_MASK;
+		offsets->dis_mask = IDT24x_REG_Q3_DIS_MASK;
+		offsets->n_17_16_offset = IDT24x_REG_N_Q3_17_16;
+		offsets->n_17_16_mask = IDT24x_REG_N_Q3_17_16_MASK;
+		offsets->n_15_8_offset = IDT24x_REG_N_Q3_15_8;
+		offsets->n_7_0_offset = IDT24x_REG_N_Q3_7_0;
+		offsets->nfrac_27_24_offset = IDT24x_REG_NFRAC_Q3_27_24;
+		offsets->nfrac_27_24_mask =
+			IDT24x_REG_NFRAC_Q3_27_24_MASK;
+		offsets->nfrac_23_16_offset = IDT24x_REG_NFRAC_Q3_23_16;
+		offsets->nfrac_15_8_offset = IDT24x_REG_NFRAC_Q3_15_8;
+		offsets->nfrac_7_0_offset = IDT24x_REG_NFRAC_Q3_7_0;
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+/**
+ * idt24x_calc_div_q0 - Calculate dividers and VCO freq to generate
+ *		the specified Q0 frequency.
+ * @chip:	Device data structure. contains all requested frequencies
+ *		for all outputs.
+ *
+ * The actual output divider is ns1 * ns2 * 2. fOutput = fVCO / (ns1 * ns2 * 2)
+ *
+ * The options for ns1 (when the source is the VCO) are 4,5,6. ns2 is a
+ * 16-bit value.
+ *
+ * chip->divs: structure for specifying ns1/ns2 values. If 0 after this
+ * function, Q0 is not requested
+ *
+ * Return: 0 on success, negative errno otherwise.
+ */
+static int idt24x_calc_div_q0(struct clk_idt24x_chip *chip)
+{
+	u8 x;
+	u32 min_div, max_div, best_vco = 0;
+	u16 min_ns2, max_ns2;
+	bool is_lower_vco = false;
+
+	chip->divs.ns1_q0 = 0;
+	chip->divs.ns2_q0 = 0;
+
+	if (chip->clk[0].requested == 0)
+		return 0;
+
+	min_div = div64_u64(
+		(u64)IDT24x_VCO_MIN, chip->clk[0].requested * 2) * 2;
+	max_div = div64_u64(
+		(u64)IDT24x_VCO_MAX, chip->clk[0].requested * 2) * 2;
+
+	dev_dbg(&chip->i2c_client->dev,
+		"%s. requested: %u, min_div: %u, max_div: %u",
+		__func__, chip->clk[0].requested, min_div, max_div);
+
+	min_ns2 = div64_u64((u64)min_div, IDT24x_MAX_NS1 * 2);
+	max_ns2 = div64_u64((u64)max_div, IDT24x_MIN_NS1 * 2);
+
+	dev_dbg(&chip->i2c_client->dev,
+		"%s. min_ns2: %u, max_ns2: %u", __func__, min_ns2, max_ns2);
+
+	for (x = 0; x < ARRAY_SIZE(q0_ns1_options); x++) {
+		u16 y = min_ns2;
+
+		while (y <= max_ns2) {
+			u32 actual_div = q0_ns1_options[x] * y * 2;
+			u32 current_vco = actual_div *
+				chip->clk[0].requested;
+
+			if (current_vco < IDT24x_VCO_MIN)
+				dev_dbg(&chip->i2c_client->dev,
+					"%s. ignore div: (ns1=%u * ns2=%u * 2 * %u) == %u < %u",
+					__func__, q0_ns1_options[x], y,
+					chip->clk[0].requested,
+					current_vco, IDT24x_VCO_MIN);
+			else if (current_vco > IDT24x_VCO_MAX) {
+				dev_dbg(&chip->i2c_client->dev,
+					"%s. ignore div: (ns1=%u * ns2=%u * 2 * %u) == %u > %u. EXIT LOOP.",
+					__func__, q0_ns1_options[x], y,
+					chip->clk[0].requested,
+					current_vco, IDT24x_VCO_MAX);
+				y = max_ns2;
+			} else {
+				bool use = false;
+
+				dev_dbg(&chip->i2c_client->dev,
+					"%s. contender: (ns1=%u * ns2=%u * 2 * %u) == %u [in range]",
+					__func__, q0_ns1_options[x], y,
+					chip->clk[0].requested,
+					current_vco);
+				if (current_vco <= IDT24x_VCO_OPT) {
+					if (current_vco > best_vco ||
+					    !is_lower_vco) {
+						is_lower_vco = true;
+						use = true;
+					}
+				} else if (!is_lower_vco &&
+					   current_vco > best_vco)
+					use = true;
+				if (use) {
+					chip->divs.ns1_q0 = x;
+					chip->divs.ns2_q0 = y;
+					best_vco = current_vco;
+				}
+			}
+			y++;
+		}
+	}
+
+	dev_dbg(&chip->i2c_client->dev,
+		"%s. best: (ns1=%u [/%u] * ns2=%u * 2 * %u) == %u",
+		__func__, chip->divs.ns1_q0, q0_ns1_options[chip->divs.ns1_q0],
+		chip->divs.ns2_q0, chip->clk[0].requested, best_vco);
+	return 0;
+}
+
+/**
+ * idt24x_calc_divs - Calculate dividers to generate the specified frequency.
+ * @chip:	Device data structure. contains all requested frequencies
+ *		for all outputs.
+ *
+ * Calculate the clock dividers (dsmint, dsmfrac for vco; ns1/ns2 for q0,
+ * n/nfrac for q1-3) for a given target frequency.
+ *
+ * Return: 0 on success, negative errno otherwise.
+ */
+static int idt24x_calc_divs(struct clk_idt24x_chip *chip)
+{
+	u32 vco = 0;
+	int result;
+
+	result = idt24x_calc_div_q0(chip);
+	if (result < 0)
+		return result;
+
+	dev_dbg(&chip->i2c_client->dev,
+		"%s: after idt24x_calc_div_q0. ns1: %u [/%u], ns2: %u",
+		__func__, chip->divs.ns1_q0, q0_ns1_options[chip->divs.ns1_q0],
+		chip->divs.ns2_q0);
+
+	chip->divs.dsmint = 0;
+	chip->divs.dsmfrac = 0;
+
+	if (chip->clk[0].requested > 0) {
+		/* Q0 is in use and is governing the actual VCO freq */
+		vco = q0_ns1_options[chip->divs.ns1_q0] * chip->divs.ns2_q0 *
+			2 * chip->clk[0].requested;
+	} else {
+		u32 freq = 0;
+		u32 walk;
+		u32 min_div, max_div;
+		bool is_lower_vco = false;
+
+		/*
+		 * Q0 is not in use. Use the first requested (fractional)
+		 * output frequency as the one controlling the VCO.
+		 */
+		for (walk = 1; walk < NUM_OUTPUTS; walk++) {
+			if (chip->clk[walk].requested != 0) {
+				freq = chip->clk[walk].requested;
+				break;
+			}
+		}
+
+		if (freq == 0) {
+			dev_err(&chip->i2c_client->dev,
+				"%s: NO FREQUENCIES SPECIFIED", __func__);
+			return -EINVAL;
+		}
+
+		/*
+		 * First, determine the min/max div for the output frequency.
+		 */
+		min_div = IDT24x_MIN_INT_DIVIDER;
+		max_div = div64_u64((u64)IDT24x_VCO_MAX, freq * 2) * 2;
+
+		dev_dbg(&chip->i2c_client->dev,
+			"%s: calc_divs for fractional output. freq: %u, min_div: %u, max_div: %u",
+			__func__, freq, min_div, max_div);
+
+		walk = min_div;
+
+		while (walk <= max_div) {
+			u32 current_vco = freq * walk;
+
+			dev_dbg(&chip->i2c_client->dev,
+				"%s: calc_divs for fractional output. walk: %u, freq: %u, vco: %u",
+				__func__, walk, freq, vco);
+			if (current_vco >= IDT24x_VCO_MIN &&
+			    vco <= IDT24x_VCO_MAX) {
+				if (current_vco <= IDT24x_VCO_OPT) {
+					if (current_vco > vco ||
+					    !is_lower_vco) {
+						is_lower_vco = true;
+						vco = current_vco;
+					}
+				} else if (!is_lower_vco && current_vco > vco) {
+					vco = current_vco;
+				}
+			}
+			/* Divider must be even. */
+			walk += 2;
+		}
+	}
+
+	if (vco != 0) {
+		u32 pfd;
+		u64 rem;
+		int x;
+
+		/* Setup dividers for outputs with fractional dividers. */
+		for (x = 1; x < NUM_OUTPUTS; x++) {
+			if (chip->clk[x].requested != 0) {
+				/*
+				 * The value written to the chip is half
+				 * the calculated divider.
+				 */
+				chip->divs.nint[x - 1] = div64_u64_rem(
+					(u64)vco,
+					chip->clk[x].requested * 2,
+					&rem);
+				chip->divs.nfrac[x - 1] = div64_u64(
+					rem * 1 << 28,
+					chip->clk[x].requested * 2);
+				dev_dbg(&chip->i2c_client->dev,
+					"%s: div to get Q%i freq %u from vco %u: int part: %u, rem: %llu, frac part: %u",
+					__func__, x,
+					chip->clk[x].requested,
+					vco, chip->divs.nint[x - 1], rem,
+					chip->divs.nfrac[x - 1]);
+			}
+		}
+
+		/* Calculate freq for pfd */
+		pfd = chip->input_clk_freq * (chip->doubler_disabled ? 1 : 2);
+
+		/*
+		 * Calculate dsmint & dsmfrac:
+		 * -----------------------------
+		 * dsm = float(vco)/float(pfd)
+		 * dsmfrac = dsm-floor(dsm) * 2^21
+		 * rem = vco % pfd
+		 * therefore:
+		 * dsmfrac = (rem * 2^21)/pfd
+		 */
+		chip->divs.dsmint = div64_u64_rem(vco, pfd, &rem);
+		chip->divs.dsmfrac = div64_u64(rem * 1 << 21, pfd);
+
+		dev_dbg(&chip->i2c_client->dev,
+			"%s: vco: %u, pfd: %u, dsmint: %u, dsmfrac: %u, rem: %llu",
+			__func__, vco, pfd, chip->divs.dsmint,
+			chip->divs.dsmfrac, rem);
+	} else {
+		dev_err(&chip->i2c_client->dev,
+			"%s: no integer divider in range found. NOT SUPPORTED.",
+			__func__);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+/**
+ * idt24x_enable_output - Enable/disable a particular output
+ * @chip:	Device data structure
+ * @output:	Output to enable/disable
+ * @enable:	Enable (true/false)
+ *
+ * Return: passes on regmap_write return value.
+ */
+static int idt24x_enable_output(
+	struct clk_idt24x_chip *chip, u8 output, bool enable)
+{
+	struct clk_register_offsets offsets;
+	int err;
+	struct i2c_client *client = chip->i2c_client;
+
+	/*
+	 * When an output is enabled, enable it in the original
+	 * data read from the chip and cached. Otherwise it may be
+	 * accidentally	turned off when another output is enabled.
+	 *
+	 * E.g., the driver starts with all outputs off in reg_out_en_x.
+	 * Q1 is enabled with the appropriate mask. Q2 is then enabled,
+	 * which results in Q1 being turned back off (because Q1 was off
+	 * in reg_out_en_x).
+	 */
+
+	err = idt24x_get_offsets(output, &offsets);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error calling idt24x_get_offsets for %d: %i",
+			__func__, output, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: q%u enable? %d. reg_out_en_x before: 0x%x, reg_out_mode_0_1 before: 0x%x, reg_out_mode_2_3 before: 0x%x, reg_qx_dis before: 0x%x",
+		__func__, output, enable, chip->reg_out_en_x,
+		chip->reg_out_mode_0_1, chip->reg_out_mode_2_3,
+		chip->reg_qx_dis);
+
+	chip->reg_out_en_x = chip->reg_out_en_x & ~offsets.oe_mask;
+	if (enable)
+		chip->reg_out_en_x |= (1 << bits_to_shift(offsets.oe_mask));
+
+	chip->reg_qx_dis = chip->reg_qx_dis & ~offsets.dis_mask;
+	dev_dbg(&client->dev,
+		"%s: q%u enable? %d. reg_qx_dis mask: 0x%x, before checking enable: 0x%x",
+		__func__, output, enable, offsets.dis_mask,
+		chip->reg_qx_dis);
+	if (!enable)
+		chip->reg_qx_dis |= (1 << bits_to_shift(offsets.dis_mask));
+
+	dev_dbg(&client->dev,
+		"%s: q%u enable? %d. reg_out_en_x after: 0x%x, reg_qx_dis after: 0x%x",
+		__func__, output, enable, chip->reg_out_en_x,
+		chip->reg_qx_dis);
+
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_OUTEN, chip->reg_out_en_x);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_OUTEN: %i",
+			__func__, err);
+		return err;
+	}
+
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_OUTMODE0_1,
+		chip->reg_out_mode_0_1);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_OUTMODE0_1: %i",
+			__func__, err);
+		return err;
+	}
+
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_OUTMODE2_3,
+		chip->reg_out_mode_2_3);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_OUTMODE2_3: %i",
+			__func__, err);
+		return err;
+	}
+
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_Q_DIS, chip->reg_qx_dis);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_Q_DIS: %i",
+			__func__, err);
+		return err;
+	}
+
+	return 0;
+}
+
+/**
+ * idt24x_update_device - write registers to the chip
+ * @chip:	Device data structure
+ *
+ * Write all values to hardware that we	have calculated.
+ *
+ * Return: passes on regmap_bulk_write return value.
+ */
+static int idt24x_update_device(struct clk_idt24x_chip *chip)
+{
+	int err;
+	struct i2c_client *client = chip->i2c_client;
+	int x = -1;
+
+	dev_dbg(&client->dev,
+		"%s: setting DSM_INT_8 (val %u @ %u)",
+		__func__, chip->divs.dsmint >> 8,
+		IDT24x_REG_DSM_INT_8);
+	err = i2cwritewithmask(
+		client, chip->regmap, IDT24x_REG_DSM_INT_8,
+		(chip->divs.dsmint >> 8) & IDT24x_REG_DSM_INT_8_MASK,
+		chip->reg_dsm_int_8, IDT24x_REG_DSM_INT_8_MASK);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_DSM_INT_8: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting DSM_INT_7_0 (val %u @ 0x%x)",
+		__func__, chip->divs.dsmint & 0xFF,
+		IDT24x_REG_DSM_INT_7_0);
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_DSM_INT_7_0,
+		chip->divs.dsmint & 0xFF);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_DSM_INT_7_0: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting IDT24x_REG_DSMFRAC_20_16 (val %u @ 0x%x)",
+		__func__, chip->divs.dsmfrac >> 16,
+		IDT24x_REG_DSMFRAC_20_16);
+	err = i2cwritewithmask(
+		client, chip->regmap, IDT24x_REG_DSMFRAC_20_16,
+		(chip->divs.dsmfrac >> 16) & IDT24x_REG_DSMFRAC_20_16_MASK,
+		chip->reg_dsm_int_8, IDT24x_REG_DSMFRAC_20_16_MASK);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_DSMFRAC_20_16: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting IDT24x_REG_DSMFRAC_15_8 (val %u @ 0x%x)",
+		__func__, (chip->divs.dsmfrac >> 8) & 0xFF,
+		IDT24x_REG_DSMFRAC_15_8);
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_DSMFRAC_15_8,
+		(chip->divs.dsmfrac >> 8) & 0xFF);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_DSMFRAC_15_8: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting IDT24x_REG_DSMFRAC_7_0 (val %u @ 0x%x)",
+		__func__, chip->divs.dsmfrac & 0xFF,
+		IDT24x_REG_DSMFRAC_7_0);
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_DSMFRAC_7_0,
+		chip->divs.dsmfrac & 0xFF);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_DSMFRAC_7_0: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting IDT24x_REG_NS1_Q0 (val %u @ 0x%x)",
+		__func__, chip->divs.ns1_q0, IDT24x_REG_NS1_Q0);
+	err = i2cwritewithmask(
+		client, chip->regmap, IDT24x_REG_NS1_Q0,
+		chip->divs.ns1_q0 & IDT24x_REG_NS1_Q0_MASK,
+		chip->reg_ns1_q0, IDT24x_REG_NS1_Q0_MASK);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_NS1_Q0: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting IDT24x_REG_NS2_Q0_15_8 (val %u @ 0x%x)",
+		__func__, (chip->divs.ns2_q0 >> 8) & 0xFF,
+		IDT24x_REG_NS2_Q0_15_8);
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_NS2_Q0_15_8,
+		(chip->divs.ns2_q0 >> 8) & 0xFF);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_NS2_Q0_15_8: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: setting IDT24x_REG_NS2_Q0_7_0 (val %u @ 0x%x)",
+		__func__, chip->divs.ns2_q0 & 0xFF,
+		IDT24x_REG_NS2_Q0_7_0);
+	err = i2cwrite(
+		client, chip->regmap, IDT24x_REG_NS2_Q0_7_0,
+		chip->divs.ns2_q0 & 0xFF);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error setting IDT24x_REG_NS2_Q0_7_0: %i",
+			__func__, err);
+		return err;
+	}
+
+	dev_dbg(&client->dev,
+		"%s: calling idt24x_enable_output for Q0. requestedFreq: %u",
+		__func__, chip->clk[0].requested);
+	idt24x_enable_output(chip, 0, chip->clk[0].requested != 0);
+
+	dev_dbg(&client->dev,
+		"%s: writing values for q1-q3", __func__);
+	for (x = 1; x < NUM_OUTPUTS; x++) {
+		struct clk_register_offsets offsets;
+
+		if (chip->clk[x].requested != 0) {
+			dev_dbg(&client->dev,
+				"%s: calling idt24x_get_offsets for %u",
+				__func__, x);
+			err = idt24x_get_offsets(x, &offsets);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error calling idt24x_get_offsets: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: (q%u, nint: %u, nfrac: %u)",
+				__func__, x, chip->divs.nint[x - 1],
+				chip->divs.nfrac[x - 1]);
+
+			dev_dbg(&client->dev,
+				"%s: setting n_17_16_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				chip->divs.nint[x - 1] >> 16,
+				offsets.n_17_16_offset);
+			err = i2cwritewithmask(
+				client, chip->regmap, offsets.n_17_16_offset,
+				(chip->divs.nint[x - 1] >> 16) &
+					offsets.n_17_16_mask,
+				chip->reg_n_qx_17_16[x - 1],
+				offsets.n_17_16_mask);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting n_17_16_offset: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: setting n_15_8_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				(chip->divs.nint[x - 1] >> 8) & 0xFF,
+				offsets.n_15_8_offset);
+			err = i2cwrite(
+				client, chip->regmap, offsets.n_15_8_offset,
+				(chip->divs.nint[x - 1] >> 8) & 0xFF);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting n_15_8_offset: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: setting n_7_0_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				chip->divs.nint[x - 1] & 0xFF,
+				offsets.n_7_0_offset);
+			err = i2cwrite(
+				client, chip->regmap, offsets.n_7_0_offset,
+				chip->divs.nint[x - 1] & 0xFF);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting n_7_0_offset: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: setting nfrac_27_24_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				(chip->divs.nfrac[x - 1] >> 24),
+				offsets.nfrac_27_24_offset);
+			err = i2cwritewithmask(
+				client, chip->regmap,
+				offsets.nfrac_27_24_offset,
+				(chip->divs.nfrac[x - 1] >> 24) &
+					offsets.nfrac_27_24_mask,
+				chip->reg_nfrac_qx_27_24[x - 1],
+				offsets.nfrac_27_24_mask);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting nfrac_27_24_offset: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: setting nfrac_23_16_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				(chip->divs.nfrac[x - 1] >> 16) & 0xFF,
+				offsets.nfrac_23_16_offset);
+			err = i2cwrite(
+				client, chip->regmap,
+				offsets.nfrac_23_16_offset,
+				(chip->divs.nfrac[x - 1] >> 16) & 0xFF);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting nfrac_23_16_offset: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: setting nfrac_15_8_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				(chip->divs.nfrac[x - 1] >> 8) & 0xFF,
+				offsets.nfrac_15_8_offset);
+			err = i2cwrite(
+				client, chip->regmap,
+				offsets.nfrac_15_8_offset,
+				(chip->divs.nfrac[x - 1] >> 8) & 0xFF);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting nfrac_15_8_offset: %i",
+					__func__, err);
+				return err;
+			}
+
+			dev_dbg(&client->dev,
+				"%s: setting nfrac_7_0_offset (q%u, val %u @ 0x%x)",
+				__func__, x,
+				chip->divs.nfrac[x - 1] & 0xFF,
+				offsets.nfrac_7_0_offset);
+			err = i2cwrite(
+				client, chip->regmap, offsets.nfrac_7_0_offset,
+				chip->divs.nfrac[x - 1] & 0xFF);
+			if (err) {
+				dev_err(&client->dev,
+					"%s: error setting nfrac_7_0_offset: %i",
+					__func__, err);
+				return err;
+			}
+		}
+		idt24x_enable_output(chip, x,
+				     chip->clk[x].requested != 0);
+		chip->clk[x].actual = chip->clk[x].requested;
+	}
+	return 0;
+}
+
+/**
+ * idt24x_set_frequency - Adjust output frequency on the attached chip.
+ * @chip:	Device data structure, including all requested frequencies.
+ *
+ * Return: 0 on success.
+ */
+int idt24x_set_frequency(struct clk_idt24x_chip *chip)
+{
+	int err;
+	struct i2c_client *client = chip->i2c_client;
+	int x;
+	bool all_disabled = true;
+
+	for (x = 0; x < NUM_OUTPUTS; x++) {
+		if (chip->clk[x].requested == 0) {
+			idt24x_enable_output(chip, x, false);
+			chip->clk[x].actual = 0;
+		} else {
+			all_disabled = false;
+		}
+	}
+
+	if (all_disabled)
+		/*
+		 * no requested frequencies, so nothing else to calculate
+		 * or write to the chip. If the consumer wants to disable
+		 * all outputs, they can request 0 for all frequencies.
+		 */
+		return 0;
+
+	if (chip->input_clk_freq == 0) {
+		dev_err(&client->dev,
+			"%s: no input frequency; can't continue.", __func__);
+		return -EINVAL;
+	}
+
+	err = idt24x_calc_divs(chip);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error calling idt24x_calc_divs: %i",
+			__func__, err);
+		return err;
+	}
+
+	err = idt24x_update_device(chip);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error updating the device: %i",
+			__func__, err);
+		return err;
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/idt/clk-idt8t49n24x-core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/idt/clk-idt8t49n24x-core.h
@@ -0,0 +1,272 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* clk-idt8t49n24x-core.h - Program 8T49N24x settings via I2C (common code)
+ *
+ * Copyright (C) 2018, Integrated Device Technology, Inc. <david.cater@idt.com>
+ *
+ * See https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
+ * This program is distributed "AS IS" and  WITHOUT ANY WARRANTY;
+ * including the implied warranties of MERCHANTABILITY, FITNESS FOR
+ * A PARTICULAR PURPOSE, or NON-INFRINGEMENT.
+ */
+
+#ifndef __IDT_CLK_IDT8T49N24X_CORE_H_
+#define __IDT_CLK_IDT8T49N24X_CORE_H_
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/regmap.h>
+
+/*
+ * The configurations in the settings file have 0x317 registers (last offset
+ * is 0x316).
+ */
+#define NUM_CONFIG_REGISTERS	0x317
+#define NUM_INPUTS		2
+#define NUM_OUTPUTS		4
+#define DEBUGFS_BUFFER_LENGTH	200
+#define WRITE_BLOCK_SIZE	32
+
+/* Non output-specific registers */
+#define IDT24x_REG_DBL_DIS		0x6C
+#define IDT24x_REG_DBL_DIS_MASK		0x01
+#define IDT24x_REG_DSM_INT_8		0x25
+#define IDT24x_REG_DSM_INT_8_MASK	0x01
+#define IDT24x_REG_DSM_INT_7_0		0x26
+#define IDT24x_REG_DSMFRAC_20_16	0x28
+#define IDT24x_REG_DSMFRAC_20_16_MASK	0x1F
+#define IDT24x_REG_DSMFRAC_15_8		0x29
+#define IDT24x_REG_DSMFRAC_7_0		0x2A
+#define IDT24x_REG_OUTEN		0x39
+#define IDT24x_REG_OUTMODE0_1		0x3E
+#define IDT24x_REG_OUTMODE2_3		0x3D
+#define IDT24x_REG_Q_DIS		0x6F
+
+/* Q0 */
+#define IDT24x_REG_OUTEN0_MASK		0x01
+#define IDT24x_REG_OUTMODE0_MASK	0x0E
+#define IDT24x_REG_Q0_DIS_MASK		0x01
+#define IDT24x_REG_NS1_Q0		0x3F
+#define IDT24x_REG_NS1_Q0_MASK		0x03
+#define IDT24x_REG_NS2_Q0_15_8		0x40
+#define IDT24x_REG_NS2_Q0_7_0		0x41
+
+/* Q1 */
+#define IDT24x_REG_OUTEN1_MASK		0x02
+#define IDT24x_REG_OUTMODE1_MASK	0xE0
+#define IDT24x_REG_Q1_DIS_MASK		0x02
+#define IDT24x_REG_N_Q1_17_16		0x42
+#define IDT24x_REG_N_Q1_17_16_MASK	0x03
+#define IDT24x_REG_N_Q1_15_8		0x43
+#define IDT24x_REG_N_Q1_7_0		0x44
+#define IDT24x_REG_NFRAC_Q1_27_24	0x57
+#define IDT24x_REG_NFRAC_Q1_27_24_MASK	0x0F
+#define IDT24x_REG_NFRAC_Q1_23_16	0x58
+#define IDT24x_REG_NFRAC_Q1_15_8	0x59
+#define IDT24x_REG_NFRAC_Q1_7_0		0x5A
+
+/* Q2 */
+#define IDT24x_REG_OUTEN2_MASK		0x04
+#define IDT24x_REG_OUTMODE2_MASK	0x0E
+#define IDT24x_REG_Q2_DIS_MASK		0x04
+#define IDT24x_REG_N_Q2_17_16		0x45
+#define IDT24x_REG_N_Q2_17_16_MASK	0x03
+#define IDT24x_REG_N_Q2_15_8		0x46
+#define IDT24x_REG_N_Q2_7_0		0x47
+#define IDT24x_REG_NFRAC_Q2_27_24	0x5B
+#define IDT24x_REG_NFRAC_Q2_27_24_MASK	0x0F
+#define IDT24x_REG_NFRAC_Q2_23_16	0x5C
+#define IDT24x_REG_NFRAC_Q2_15_8	0x5D
+#define IDT24x_REG_NFRAC_Q2_7_0		0x5E
+
+/* Q3 */
+#define IDT24x_REG_OUTEN3_MASK		0x08
+#define IDT24x_REG_OUTMODE3_MASK	0xE0
+#define IDT24x_REG_Q3_DIS_MASK		0x08
+#define IDT24x_REG_N_Q3_17_16		0x48
+#define IDT24x_REG_N_Q3_17_16_MASK	0x03
+#define IDT24x_REG_N_Q3_15_8		0x49
+#define IDT24x_REG_N_Q3_7_0		0x4A
+#define IDT24x_REG_NFRAC_Q3_27_24	0x5F
+#define IDT24x_REG_NFRAC_Q3_27_24_MASK	0x0F
+#define IDT24x_REG_NFRAC_Q3_23_16	0x60
+#define IDT24x_REG_NFRAC_Q3_15_8	0x61
+#define IDT24x_REG_NFRAC_Q3_7_0		0x62
+
+/**
+ * struct idt24x_output - device output information
+ * @hw:		hw registration info for this specific output clcok. This gets
+ *		passed as an argument to CCF api calls (e.g., set_rate).
+ *		container_of can then be used to get the reference to this
+ *		struct.
+ * @chip:	store a reference to the parent device structure. container_of
+ *		cannot be used to get to the parent device structure from
+ *		idt24x_output, because clk_idt24x_chip contains an array of
+ *		output structs (for future enhancements to support devices
+ *		with different numbers of output clocks).
+ * @index:	identifies output on the chip; used in debug statements
+ * @requested:	requested output clock frequency (in Hz)
+ * @actual:	actual output clock frequency (in Hz). Will only be set after
+ *		successful update of the device.
+ * @debug_freq:	stores value for debugfs file. Use this instead of requested
+ *		struct var because debugfs expects u64, not u32.
+ */
+struct idt24x_output {
+	struct clk_hw hw;
+	struct clk_idt24x_chip *chip;
+	u8 index;
+	u32 requested;
+	u32 actual;
+	u64 debug_freq;
+};
+
+/**
+ * struct idt24x_dividers - output dividers
+ * @dsmint:	int component of feedback divider for VCO (2-stage divider)
+ * @dsmfrac:	fractional component of feedback divider for VCO
+ * @ns1_q0:	ns1 divider component for Q0
+ * @ns2_q0:	ns2 divider component for Q0
+ * @nint:	int divider component for Q1-3
+ * @nfrac:	fractional divider component for Q1-3
+ */
+struct idt24x_dividers {
+	u16 dsmint;
+	u32 dsmfrac;
+
+	u8 ns1_q0;
+	u16 ns2_q0;
+
+	u32 nint[3];
+	u32 nfrac[3];
+};
+
+/**
+ * struct clk_idt24x_chip - device info for chip
+ * @regmap:		register map used to perform i2c writes to the chip
+ * @i2c_client:		i2c_client struct passed to probe
+ * @min_freq:		min frequency for this chip
+ * @max_freq:		max frequency for this chip
+ * @settings:		filled in if full register map is specified in the DT
+ * @has_settings:	true if settings array is valid
+ * @input_clk:		ptr to input clock specified in DT
+ * @input_clk_num:	which input clock was specified. 0-based. A value of
+ *			NUM_INPUTS indicates that a XTAL is used as the input.
+ * @input_clk_nb:	notification support (if input clk changes)
+ * @input_clk_freq:	current freq of input_clk
+ * @doubler_disabled:	whether input doubler is enabled. This value is read
+ *			from the hw on probe (in case it is set in @settings).
+ * @clk:		array of outputs. One entry per output supported by the
+ *			chip. Frequencies requested via the ccf api will be
+ *			recorded in this array.
+ * @reg_dsm_int_8:	record current value from hw to avoid modifying
+ *			when writing register values
+ * @reg_dsm_frac_20_16:	record current value
+ * @reg_out_en_x:	record current value
+ * @reg_out_mode_0_1:	record current value
+ * @reg_out_mode_2_3:	record current value
+ * @reg_qx_dis:		record current value
+ * @reg_ns1_q0:		record current value
+ * @reg_n_qx_17_16:	record current value
+ * @reg_nfrac_qx_27_24:	record current value
+ * @divs:		output divider values for all outputs
+ * @debugfs_dirroot:	debugfs support
+ * @debugfs_fileaction:	debugfs support
+ * @debugfs_filei2c:	debugfs support
+ * @debugfs_map:	debugfs support
+ * @dbg_cache:		debugfs support
+ * @debugfs_fileqfreq:	debugfs support
+ */
+struct clk_idt24x_chip {
+	struct regmap *regmap;
+	struct i2c_client *i2c_client;
+
+	u32 min_freq;
+	u32 max_freq;
+
+	u8 settings[NUM_CONFIG_REGISTERS];
+
+	bool has_settings;
+
+	struct clk *input_clk;
+	int input_clk_num;
+	struct notifier_block input_clk_nb;
+	u32 input_clk_freq;
+
+	bool doubler_disabled;
+
+	struct idt24x_output clk[NUM_OUTPUTS];
+
+	unsigned int reg_dsm_int_8;
+	unsigned int reg_dsm_frac_20_16;
+	unsigned int reg_out_en_x;
+	unsigned int reg_out_mode_0_1;
+	unsigned int reg_out_mode_2_3;
+	unsigned int reg_qx_dis;
+	unsigned int reg_ns1_q0;
+	unsigned int reg_n_qx_17_16[3];
+	unsigned int reg_nfrac_qx_27_24[3];
+
+	struct idt24x_dividers divs;
+
+	struct dentry *debugfs_dirroot, *debugfs_fileaction, *debugfs_filei2c,
+		*debugfs_map;
+	char dbg_cache[DEBUGFS_BUFFER_LENGTH];
+	struct dentry *debugfs_fileqfreq[4];
+};
+
+#define to_idt24x_output(_hw) \
+	container_of(_hw, struct idt24x_output, hw)
+#define to_clk_idt24x_from_client(_client) \
+	container_of(_client, struct clk_idt24x_chip, i2c_client)
+#define to_clk_idt24x_from_nb(_nb) \
+	container_of(_nb, struct clk_idt24x_chip, input_clk_nb)
+
+/**
+ * struct clk_register_offsets - register offsets for current context
+ * @oe_offset:		offset for current output enable and mode
+ * @oe_mask:		mask for current output enable
+ * @dis_mask:		mask for current output disable
+ * @n_17_16_offset:	offset for current output int divider (bits 17:16)
+ * @n_17_16_mask:	mask for current output int divider (bits 17:16)
+ * @n_15_8_offset:	offset for current output int divider (bits 15:8)
+ * @n_7_0_offset:	offset for current output int divider (bits 7:0)
+ * @nfrac_27_24_offset:	offset for current output frac divider (bits 27:24)
+ * @nfrac_27_24_mask:	mask for current output frac divider (bits 27:24)
+ * @nfrac_23_16_offset:	offset for current output frac divider (bits 23:16)
+ * @nfrac_15_8_offset:	offset for current output frac divider (bits 15:8)
+ * @nfrac_7_0_offset:	offset for current output frac divider (bits 7:0)
+ * @ns1_offset:		offset for stage 1 div for output Q0
+ * @ns1_offset_mask:	mask for stage 1 div for output Q0
+ * @ns2_15_8_offset:	offset for stage 2 div for output Q0 (bits 15:8)
+ * @ns2_7_0_offset:	offset for stage 2 div for output Q0 (bits 7:0)
+ */
+struct clk_register_offsets {
+	u16 oe_offset;
+	u8 oe_mask;
+	u8 dis_mask;
+
+	u16 n_17_16_offset;
+	u8 n_17_16_mask;
+	u16 n_15_8_offset;
+	u16 n_7_0_offset;
+	u16 nfrac_27_24_offset;
+	u8 nfrac_27_24_mask;
+	u16 nfrac_23_16_offset;
+	u16 nfrac_15_8_offset;
+	u16 nfrac_7_0_offset;
+
+	u16 ns1_offset;
+	u8 ns1_offset_mask;
+	u16 ns2_15_8_offset;
+	u16 ns2_7_0_offset;
+};
+
+int bits_to_shift(unsigned int mask);
+int i2cwritebulk(
+	struct i2c_client *client, struct regmap *map,
+	unsigned int reg, u8 val[], size_t val_count);
+int idt24x_get_offsets(
+	u8 output_num,
+	struct clk_register_offsets *offsets);
+int idt24x_set_frequency(struct clk_idt24x_chip *chip);
+
+#endif /* __IDT_CLK_IDT8T49N24X_CORE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/idt/clk-idt8t49n24x-debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/idt/clk-idt8t49n24x-debugfs.c
@@ -0,0 +1,375 @@
+// SPDX-License-Identifier: GPL-2.0
+/* clk-idt8t49n24x-debugfs.c - Debugfs support for 8T49N24x
+ *
+ * Copyright (C) 2018, Integrated Device Technology, Inc. <david.cater@idt.com>
+ *
+ * See https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
+ * This program is distributed "AS IS" and  WITHOUT ANY WARRANTY;
+ * including the implied warranties of MERCHANTABILITY, FITNESS FOR
+ * A PARTICULAR PURPOSE, or NON-INFRINGEMENT.
+ */
+
+#include <linux/debugfs.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include "clk-idt8t49n24x-debugfs.h"
+
+static struct clk_idt24x_chip *idt24x_chip_fordebugfs;
+
+static int idt24x_read_all_settings(
+	struct clk_idt24x_chip *chip, char *output_buffer, int count)
+{
+	u8 settings[NUM_CONFIG_REGISTERS];
+	int err = 0;
+	int x;
+
+	err = regmap_bulk_read(
+		chip->regmap, 0x0, settings, NUM_CONFIG_REGISTERS);
+	if (!err) {
+		output_buffer[0] = '\0';
+		for (x = 0; x < ARRAY_SIZE(settings); x++) {
+			char dbg[4];
+
+			if ((strlen(output_buffer) + 4) > count)
+				return -EINVAL;
+			sprintf(dbg, "%02x ", settings[x]);
+			strcat(output_buffer, dbg);
+		}
+	}
+	return err;
+}
+
+/**
+ * idt24x_debugfs_writer_action - Write handler for the "action" debugfs file.
+ * @fp:			file pointer
+ * @user_buffer:	buffer of text written to file
+ * @count:		size of text in buffer
+ * @position:		pass in current position, return new position
+ *
+ * Return: result of call to simple_write_to_buffer
+ *
+ * Use the "action" file as a trigger for setting all requested
+ * rates. The driver doesn't get any notification when the files
+ * representing the Qx outputs are written to, so something else is
+ * needed to notify the driver that the device should be udpated.
+ *
+ * It doesn't matter what you write to the action debugs file. When the
+ * handler is called, the device will be updated.
+ */
+static ssize_t idt24x_debugfs_writer_action(
+	struct file *fp, const char __user *user_buffer,
+	size_t count, loff_t *position)
+{
+	int err = 0;
+	int x;
+	u32 freq;
+	bool needs_update = true;
+	struct i2c_client *client = idt24x_chip_fordebugfs->i2c_client;
+
+	if (count > DEBUGFS_BUFFER_LENGTH)
+		return -EINVAL;
+
+	for (x = 0; x < NUM_OUTPUTS; x++) {
+		freq = idt24x_chip_fordebugfs->clk[x].debug_freq;
+		if (freq) {
+			needs_update = false;
+			dev_dbg(&client->dev,
+				"%s: calling clk_set_rate with debug frequency for Q%i",
+				__func__, x);
+			err = clk_set_rate(
+				idt24x_chip_fordebugfs->clk[x].hw.clk, freq);
+			if (err) {
+				dev_err(&client->dev,
+					"error calling clk_set_rate for Q%i (%i)\n",
+					x, err);
+			}
+		} else {
+			needs_update = true;
+			idt24x_chip_fordebugfs->clk[x].requested = 0;
+			dev_dbg(&client->dev,
+				"%s: debug frequency for Q%i not set; make sure clock is disabled",
+				__func__, x);
+		}
+	}
+
+	if (needs_update) {
+		dev_dbg(&client->dev,
+			"%s: calling idt24x_set_frequency to ensure any clocks that should be disabled are turned off.",
+			__func__);
+		err = idt24x_set_frequency(idt24x_chip_fordebugfs);
+		if (err) {
+			dev_err(&idt24x_chip_fordebugfs->i2c_client->dev,
+				"%s: error calling idt24x_set_frequency (%i)\n",
+				__func__, err);
+			return err;
+		}
+	}
+
+	return simple_write_to_buffer(
+		idt24x_chip_fordebugfs->dbg_cache, DEBUGFS_BUFFER_LENGTH,
+		position, user_buffer, count);
+}
+
+/**
+ * idt24x_debugfs_reader_action - Read the "action" debugfs file.
+ * @fp:			file pointer
+ * @user_buffer:	buffer of text written to file
+ * @count:		size of text in buffer
+ * @position:		pass in current position, return new position
+ *
+ * Return: whatever was last written to the "action" debugfs file.
+ */
+static ssize_t idt24x_debugfs_reader_action(
+	struct file *fp, char __user *user_buffer, size_t count,
+	loff_t *position)
+{
+	return simple_read_from_buffer(
+		user_buffer, count, position, idt24x_chip_fordebugfs->dbg_cache,
+		DEBUGFS_BUFFER_LENGTH);
+}
+
+/**
+ * idt24x_debugfs_reader_map - display the current registers on the device
+ * @fp:			file pointer
+ * @user_buffer:	buffer of text written to file
+ * @count:		size of text in buffer
+ * @position:		pass in current position, return new position
+ *
+ * Reads the current register map from the attached chip via I2C and
+ * returns it.
+ *
+ * Return: result of call to simple_read_from_buffer
+ */
+static ssize_t idt24x_debugfs_reader_map(
+	struct file *fp, char __user *user_buffer, size_t count,
+	loff_t *position)
+{
+	int err = 0;
+	char *buf = kzalloc(5000, GFP_KERNEL);
+
+	dev_dbg(&idt24x_chip_fordebugfs->i2c_client->dev,
+		"calling idt24x_read_all_settings (count: %zu)\n", count);
+	err = idt24x_read_all_settings(idt24x_chip_fordebugfs, buf, 5000);
+	if (err) {
+		dev_err(&idt24x_chip_fordebugfs->i2c_client->dev,
+			"error calling idt24x_read_all_settings (%i)\n", err);
+		return 0;
+	}
+	/* TMGCDR-1456. We're returning 1 byte too few. */
+	err = simple_read_from_buffer(
+		user_buffer, count, position, buf, strlen(buf));
+	kfree(buf);
+	return err;
+}
+
+/**
+ * idt24x_handle_i2c_debug_token - process "token" written to the i2c file
+ * @dev:	pointer to device structure
+ * @token:	pointer to current char being examined
+ * @reg:	pass in current register, or return register from token.
+ * @val:	resulting array of bytes being parsed
+ * @nextbyte:	position in val array to store next byte
+ *
+ * Utility function to operate on the current "token" (from within a
+ * space-delimited string) written to the i2c debugfs file. It will
+ * either be a register offset or a byte to be added to the val array.
+ * If it is added to the val array, auto-increment nextbyte.
+ *
+ * Return:	0 for success
+ */
+static int idt24x_handle_i2c_debug_token(
+	const struct device *dev, char *token, unsigned int *reg,
+	u8 val[], u16 *nextbyte)
+{
+	int err = 0;
+
+	dev_dbg(dev, "got token (%s)\n", token);
+	if (*reg == -1) {
+		err = kstrtouint(token, 16, reg);
+		if (!err)
+			dev_dbg(dev, "hex register address == 0x%x\n", *reg);
+	} else {
+		u8 temp;
+
+		err = kstrtou8(token, 16, &temp);
+		if (!err) {
+			dev_dbg(dev, "data byte == 0x%x\n", temp);
+			val[*nextbyte] = temp;
+			*nextbyte += 1;
+		}
+	}
+	if (err == -ERANGE)
+		dev_err(dev, "ERANGE error when parsing data\n");
+	else if (err == -EINVAL)
+		dev_err(dev, "EINVAL error when parsing data\n");
+	else if (err)
+		dev_err(dev, "error when parsing data: %i\n", err);
+	return err;
+}
+
+/**
+ * idt24x_debugfs_writer_i2c - debugfs handler for i2c file
+ * @fp:			file pointer
+ * @user_buffer:	buffer of text written to file
+ * @count:		size of text in buffer
+ * @position:		pass in current position, return new position
+ *
+ * Handler for the "i2c" debugfs file. Write to this file to write bytes
+ * via I2C to a particular offset.
+ *
+ * Usage: echo 006c 01 02 0D FF > i2c
+ *
+ * First 4 chars are the 2-byte i2c register offset. Then follow that
+ * with a sequence of 2-char bytes in hex format that you want to write
+ * starting at that offset.
+ *
+ * Return: result of simple_write_to_buffer
+ */
+static ssize_t idt24x_debugfs_writer_i2c(struct file *fp,
+					 const char __user *user_buffer,
+					 size_t count, loff_t *position)
+{
+	int err = 0;
+	int x = 0;
+	int start = 0;
+	ssize_t written;
+	unsigned int reg = -1;
+	u8 val[WRITE_BLOCK_SIZE];
+	u16 nextbyte = 0;
+	char token[16];
+
+	if (count > DEBUGFS_BUFFER_LENGTH)
+		return -EINVAL;
+
+	written = simple_write_to_buffer(
+		idt24x_chip_fordebugfs->dbg_cache, DEBUGFS_BUFFER_LENGTH,
+		position, user_buffer, count);
+	if (written != count) {
+		dev_dbg(&idt24x_chip_fordebugfs->i2c_client->dev,
+			"write count != expected count");
+		return written;
+	}
+
+	for (x = 0; x < count; x++) {
+		token[x - start] = idt24x_chip_fordebugfs->dbg_cache[x];
+		if (idt24x_chip_fordebugfs->dbg_cache[x] == ' ') {
+			token[x - start] = '\0';
+			err = idt24x_handle_i2c_debug_token(
+				&idt24x_chip_fordebugfs->i2c_client->dev,
+				token, &reg, val, &nextbyte);
+			if (err)
+				break;
+			start = x + 1;
+		}
+	}
+
+	/* handle the last token */
+	if (!err) {
+		token[count - start] = '\0';
+		err = idt24x_handle_i2c_debug_token(
+			&idt24x_chip_fordebugfs->i2c_client->dev, token, &reg,
+			val, &nextbyte);
+	}
+
+	if (!err && reg != -1 && nextbyte > 0) {
+		err = i2cwritebulk(
+			idt24x_chip_fordebugfs->i2c_client,
+			idt24x_chip_fordebugfs->regmap,
+			reg, val, nextbyte);
+		if (err) {
+			dev_err(&idt24x_chip_fordebugfs->i2c_client->dev,
+				"error writing data chip (%i)\n", err);
+			return err;
+		}
+		dev_dbg(&idt24x_chip_fordebugfs->i2c_client->dev,
+			"successfully wrote i2c data to chip");
+	}
+
+	return written;
+}
+
+static const struct file_operations idt24x_fops_debug_action = {
+	.read = idt24x_debugfs_reader_action,
+	.write = idt24x_debugfs_writer_action,
+};
+
+static const struct file_operations idt24x_fops_debug_map = {
+	.read = idt24x_debugfs_reader_map
+};
+
+static const struct file_operations idt24x_fops_debug_i2c = {
+	.write = idt24x_debugfs_writer_i2c,
+};
+
+/**
+ * idt24x_expose_via_debugfs - Set up all debugfs files
+ * @client:	pointer to i2c_client structure
+ * @chip:	Device data structure
+ *
+ * Sets up all debugfs files to use for debugging the driver.
+ * Return: error code. 0 if success or debugfs doesn't appear to be enabled.
+ */
+int idt24x_expose_via_debugfs(struct i2c_client *client,
+			      struct clk_idt24x_chip *chip)
+{
+	int output_num;
+
+	/*
+	 * create root directory in /sys/kernel/debugfs
+	 */
+	chip->debugfs_dirroot = debugfs_create_dir("idt24x", NULL);
+	if (!chip->debugfs_dirroot) {
+		/* debugfs probably not enabled. Don't fail the probe. */
+		return 0;
+	}
+
+	/*
+	 * create files in the root directory. This requires read and
+	 * write file operations
+	 */
+	chip->debugfs_fileaction = debugfs_create_file(
+		"action", 0644, chip->debugfs_dirroot, NULL,
+		&idt24x_fops_debug_action);
+	if (!chip->debugfs_fileaction) {
+		dev_err(&client->dev,
+			"%s: error creating action file", __func__);
+		return (-ENODEV);
+	}
+
+	chip->debugfs_map = debugfs_create_file(
+		"map", 0444, chip->debugfs_dirroot, NULL,
+		&idt24x_fops_debug_map);
+	if (!chip->debugfs_map) {
+		dev_err(&client->dev,
+			"%s: error creating map file", __func__);
+		return (-ENODEV);
+	}
+
+	for (output_num = 0; output_num < NUM_OUTPUTS; output_num++) {
+		char name[5];
+
+		sprintf(name, "q%d", output_num);
+		debugfs_create_u64(name, 0644, chip->debugfs_dirroot,
+				   &chip->clk[output_num].debug_freq);
+	}
+
+	chip->debugfs_filei2c = debugfs_create_file(
+		"i2c", 0644, chip->debugfs_dirroot, NULL,
+		&idt24x_fops_debug_i2c);
+	if (!chip->debugfs_filei2c) {
+		dev_err(&client->dev,
+			"%s: error creating i2c file", __func__);
+		return (-ENODEV);
+	}
+
+	dev_dbg(&client->dev, "%s: success", __func__);
+	idt24x_chip_fordebugfs = chip;
+	return 0;
+}
+
+void idt24x_cleanup_debugfs(struct clk_idt24x_chip *chip)
+{
+	debugfs_remove_recursive(chip->debugfs_dirroot);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/idt/clk-idt8t49n24x-debugfs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/idt/clk-idt8t49n24x-debugfs.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* clk-idt8t49n24x-debugfs.h - Debugfs support for 8T49N24x
+ *
+ * Copyright (C) 2018, Integrated Device Technology, Inc. <david.cater@idt.com>
+ *
+ * See https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
+ * This program is distributed "AS IS" and  WITHOUT ANY WARRANTY;
+ * including the implied warranties of MERCHANTABILITY, FITNESS FOR
+ * A PARTICULAR PURPOSE, or NON-INFRINGEMENT.
+ */
+
+#ifndef __IDT_CLK_IDT8T49N24X_DEBUGFS_H_
+#define __IDT_CLK_IDT8T49N24X_DEBUGFS_H_
+
+#include "clk-idt8t49n24x-core.h"
+
+int idt24x_expose_via_debugfs(struct i2c_client *client,
+			      struct clk_idt24x_chip *chip);
+void idt24x_cleanup_debugfs(struct clk_idt24x_chip *chip);
+
+#endif /* __IDT_CLK_IDT8T49N24X_DEBUGFS_H_*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/idt/clk-idt8t49n24x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/idt/clk-idt8t49n24x.c
@@ -0,0 +1,641 @@
+// SPDX-License-Identifier: GPL-2.0
+/* clk-idt8t49n24x.c - Program 8T49N24x settings via I2C.
+ *
+ * Copyright (C) 2018, Integrated Device Technology, Inc. <david.cater@idt.com>
+ *
+ * See https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
+ * This program is distributed "AS IS" and  WITHOUT ANY WARRANTY;
+ * including the implied warranties of MERCHANTABILITY, FITNESS FOR
+ * A PARTICULAR PURPOSE, or NON-INFRINGEMENT.
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include "clk-idt8t49n24x-core.h"
+#include "clk-idt8t49n24x-debugfs.h"
+
+#define OUTPUTMODE_HIGHZ	0
+#define OUTPUTMODE_LVDS		2
+#define IDT24x_MIN_FREQ		1000000L
+#define IDT24x_MAX_FREQ		300000000L
+#define DRV_NAME		"idt8t49n24x"
+
+enum clk_idt24x_variant {
+	idt24x
+};
+
+static u32 mask_and_shift(u32 value, u8 mask)
+{
+	value &= mask;
+	return value >> bits_to_shift(mask);
+}
+
+/**
+ * idt24x_set_output_mode - Set the mode for a particular clock
+ * output in the register.
+ * @reg:	The current register value before setting the mode.
+ * @mask:	The bitmask identifying where in the register the
+ *		output mode is stored.
+ * @mode:	The mode to set.
+ *
+ * Return: the new register value with the specified mode bits set.
+ */
+static int idt24x_set_output_mode(u32 reg, u8 mask, u8 mode)
+{
+	if (((reg & mask) >> bits_to_shift(mask)) == OUTPUTMODE_HIGHZ) {
+		reg = reg & ~mask;
+		reg |= (OUTPUTMODE_LVDS << bits_to_shift(mask));
+	}
+	return reg;
+}
+
+/**
+ * idt24x_read_from_hw - Get the current values on the hw
+ * @chip:	Device data structure
+ *
+ * Return: 0 on success, negative errno otherwise.
+ */
+static int idt24x_read_from_hw(struct clk_idt24x_chip *chip)
+{
+	int err;
+	struct i2c_client *client = chip->i2c_client;
+	u32 tmp, tmp2;
+	u8 output;
+
+	err = regmap_read(chip->regmap, IDT24x_REG_DSM_INT_8,
+			  &chip->reg_dsm_int_8);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_DSM_INT_8: %i",
+			__func__, err);
+		return err;
+	}
+	dev_dbg(&client->dev, "%s: reg_dsm_int_8: 0x%x",
+		__func__, chip->reg_dsm_int_8);
+
+	err = regmap_read(chip->regmap, IDT24x_REG_DSMFRAC_20_16_MASK,
+			  &chip->reg_dsm_frac_20_16);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_DSMFRAC_20_16_MASK: %i",
+			__func__, err);
+		return err;
+	}
+	dev_dbg(&client->dev, "%s: reg_dsm_frac_20_16: 0x%x",
+		__func__, chip->reg_dsm_frac_20_16);
+
+	err = regmap_read(chip->regmap, IDT24x_REG_OUTEN, &chip->reg_out_en_x);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_OUTEN: %i",
+			__func__, err);
+		return err;
+	}
+	dev_dbg(&client->dev, "%s: reg_out_en_x: 0x%x",
+		__func__, chip->reg_out_en_x);
+
+	err = regmap_read(chip->regmap, IDT24x_REG_OUTMODE0_1, &tmp);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_OUTMODE0_1: %i",
+			__func__, err);
+		return err;
+	}
+
+	tmp2 = idt24x_set_output_mode(
+		tmp, IDT24x_REG_OUTMODE0_MASK, OUTPUTMODE_LVDS);
+	tmp2 = idt24x_set_output_mode(
+		tmp2, IDT24x_REG_OUTMODE1_MASK, OUTPUTMODE_LVDS);
+	dev_dbg(&client->dev,
+		"%s: reg_out_mode_0_1 original: 0x%x. After setting OUT0/1 to LVDS if necessary: 0x%x",
+		__func__, tmp, tmp2);
+	chip->reg_out_mode_0_1 = tmp2;
+
+	err = regmap_read(chip->regmap, IDT24x_REG_OUTMODE2_3, &tmp);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_OUTMODE2_3: %i",
+			__func__, err);
+		return err;
+	}
+
+	tmp2 = idt24x_set_output_mode(
+		tmp, IDT24x_REG_OUTMODE2_MASK, OUTPUTMODE_LVDS);
+	tmp2 = idt24x_set_output_mode(
+		tmp2, IDT24x_REG_OUTMODE3_MASK, OUTPUTMODE_LVDS);
+	dev_dbg(&client->dev,
+		"%s: reg_out_mode_2_3 original: 0x%x. After setting OUT2/3 to LVDS if necessary: 0x%x",
+		__func__, tmp, tmp2);
+	chip->reg_out_mode_2_3 = tmp2;
+
+	err = regmap_read(chip->regmap, IDT24x_REG_Q_DIS, &chip->reg_qx_dis);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_Q_DIS: %i",
+			__func__, err);
+		return err;
+	}
+	dev_dbg(&client->dev, "%s: reg_qx_dis: 0x%x",
+		__func__, chip->reg_qx_dis);
+
+	err = regmap_read(chip->regmap, IDT24x_REG_NS1_Q0, &chip->reg_ns1_q0);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_NS1_Q0: %i",
+			__func__, err);
+		return err;
+	}
+	dev_dbg(&client->dev, "%s: reg_ns1_q0: 0x%x",
+		__func__, chip->reg_ns1_q0);
+
+	for (output = 1; output <= 3; output++) {
+		struct clk_register_offsets offsets;
+
+		err = idt24x_get_offsets(output, &offsets);
+		if (err) {
+			dev_err(&client->dev,
+				"%s: error calling idt24x_get_offsets: %i",
+				__func__, err);
+			return err;
+		}
+
+		err = regmap_read(chip->regmap, offsets.n_17_16_offset,
+				  &chip->reg_n_qx_17_16[output - 1]);
+		if (err) {
+			dev_err(&client->dev,
+				"%s: error reading n_17_16_offset for output %d (offset: 0x%x): %i",
+				__func__, output, offsets.n_17_16_offset, err);
+			return err;
+		}
+		dev_dbg(&client->dev,
+			"%s: reg_n_qx_17_16[Q%u]: 0x%x",
+			__func__, output, chip->reg_n_qx_17_16[output - 1]);
+
+		err = regmap_read(chip->regmap, offsets.nfrac_27_24_offset,
+				  &chip->reg_nfrac_qx_27_24[output - 1]);
+		if (err) {
+			dev_err(&client->dev,
+				"%s: error reading nfrac_27_24_offset for output %d (offset: 0x%x): %i",
+				__func__, output,
+				offsets.nfrac_27_24_offset, err);
+			return err;
+		}
+		dev_dbg(&client->dev,
+			"%s: reg_nfrac_qx_27_24[Q%u]: 0x%x",
+			__func__, output,
+			chip->reg_nfrac_qx_27_24[output - 1]);
+	}
+
+	dev_info(&client->dev,
+		 "%s: initial values read from chip successfully",
+		 __func__);
+
+	/* Also read DBL_DIS to determine whether the doubler is disabled. */
+	err = regmap_read(chip->regmap, IDT24x_REG_DBL_DIS, &tmp);
+	if (err) {
+		dev_err(&client->dev,
+			"%s: error reading IDT24x_REG_DBL_DIS: %i",
+			__func__, err);
+		return err;
+	}
+	chip->doubler_disabled = mask_and_shift(tmp, IDT24x_REG_DBL_DIS_MASK);
+	dev_dbg(&client->dev, "%s: doubler_disabled: %d",
+		__func__, chip->doubler_disabled);
+
+	return 0;
+}
+
+/**
+ * idt24x_set_rate - Sets the specified output clock to the specified rate.
+ * @hw:		clk_hw struct that identifies the specific output clock.
+ * @rate:	the rate (in Hz) for the specified clock.
+ * @parent_rate:(not sure) the rate for a parent signal (e.g.,
+ *		the VCO feeding the output)
+ *
+ * This function will call idt24_set_frequency, which means it will
+ * calculate divider for all requested outputs and update the attached
+ * device (issue I2C commands to update the registers).
+ *
+ * Return: 0 on success.
+ */
+static int idt24x_set_rate(struct clk_hw *hw, unsigned long rate,
+			   unsigned long parent_rate)
+{
+	int err = 0;
+
+	/*
+	 * hw->clk is the pointer to the specific output clock the user is
+	 * requesting. We use hw to get back to the output structure for
+	 * the output clock. Set the requested rate in the output structure.
+	 * Note that container_of cannot be used to find the device structure
+	 * (clk_idt24x_chip) from clk_hw, because clk_idt24x_chip has an array
+	 * of idt24x_output structs. That is why it is necessary to use
+	 * output->chip to access the device structure.
+	 */
+	struct idt24x_output *output = to_idt24x_output(hw);
+	struct i2c_client *client = output->chip->i2c_client;
+
+	if (rate < output->chip->min_freq || rate > output->chip->max_freq) {
+		dev_err(&client->dev,
+			"requested frequency (%luHz) is out of range\n", rate);
+		return -EINVAL;
+	}
+
+	/*
+	 * Set the requested frequency in the output data structure, and then
+	 * call idt24x_set_frequency. idt24x_set_frequency considers all
+	 * requested frequencies when deciding on a vco frequency and
+	 * calculating dividers.
+	 */
+	output->requested = rate;
+
+	/*
+	 * Also set in the memory location used by the debugfs file
+	 * that exposes the output clock frequency. That allows querying
+	 * the current rate via debugfs.
+	 */
+	output->debug_freq = rate;
+
+	dev_info(&client->dev,
+		 "%s. calling idt24x_set_frequency for Q%u. rate: %lu",
+		 __func__, output->index, rate);
+	err = idt24x_set_frequency(output->chip);
+
+	if (err != 0)
+		dev_err(&client->dev, "error calling set_frequency: %d", err);
+
+	return err;
+}
+
+/**
+ * idt24x_round_rate - get valid rate that is closest to the requested rate
+ * @hw:		clk_hw struct that identifies the specific output clock.
+ * @rate:	the rate (in Hz) for the specified clock.
+ * @parent_rate:(not sure) the rate for a parent signal (e.g., the VCO
+ *		feeding the output). This is an i/o param.
+ *		If the driver supports a parent clock for the output (e.g.,
+ *		the VCO(?), then set this param to indicate what the rate of
+ *		the parent would be (e.g., the VCO frequency) if the rounded
+ *		rate is used.
+ *
+ * Returns the closest rate to the requested rate actually supported by the
+ * chip.
+ *
+ * Return: adjusted rate
+ */
+static long idt24x_round_rate(struct clk_hw *hw, unsigned long rate,
+			      unsigned long *parent_rate)
+{
+	/*
+	 * The chip has fractional output dividers, so assume it
+	 * can provide the requested rate.
+	 *
+	 * TODO: figure out the closest rate that chip can support
+	 * within a low error threshold and return that rate.
+	 */
+	return rate;
+}
+
+/**
+ * idt24x_recalc_rate - return the frequency being provided by the clock.
+ * @hw:			clk_hw struct that identifies the specific output clock.
+ * @parent_rate:	(not sure) the rate for a parent signal (e.g., the
+ *			VCO feeding the output)
+ *
+ * This API appears to be used to read the current values from the hardware
+ * and report the frequency being provided by the clock. Without this function,
+ * the clock will be initialized to 0 by default. The OS appears to be
+ * calling this to find out what the current value of the clock is at
+ * startup, so it can determine when .set_rate is actually changing the
+ * frequency.
+ *
+ * Return: the frequency of the specified clock.
+ */
+static unsigned long idt24x_recalc_rate(struct clk_hw *hw,
+					unsigned long parent_rate)
+{
+	struct idt24x_output *output = to_idt24x_output(hw);
+
+	return output->requested;
+}
+
+/*
+ * Note that .prepare and .unprepare appear to be used more in Gates.
+ * They do not appear to be necessary for this device.
+ * Instead, update the device when .set_rate is called.
+ */
+static const struct clk_ops idt24x_clk_ops = {
+	.recalc_rate = idt24x_recalc_rate,
+	.round_rate = idt24x_round_rate,
+	.set_rate = idt24x_set_rate,
+};
+
+static bool idt24x_regmap_is_volatile(struct device *dev, unsigned int reg)
+{
+	return false;
+}
+
+static bool idt24x_regmap_is_writeable(struct device *dev, unsigned int reg)
+{
+	return true;
+}
+
+static const struct regmap_config idt24x_regmap_config = {
+	.reg_bits = 16,
+	.val_bits = 8,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = 0xffff,
+	.writeable_reg = idt24x_regmap_is_writeable,
+	.volatile_reg = idt24x_regmap_is_volatile,
+};
+
+/**
+ * idt24x_clk_notifier_cb - Clock rate change callback
+ * @nb:		Pointer to notifier block
+ * @event:	Notification reason
+ * @data:	Pointer to notification data object
+ *
+ * This function is called when the input clock frequency changes.
+ * The callback checks whether a valid bus frequency can be generated after the
+ * change. If so, the change is acknowledged, otherwise the change is aborted.
+ * New dividers are written to the HW in the pre- or post change notification
+ * depending on the scaling direction.
+ *
+ * Return:	NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
+ *		to acknowledge the change, NOTIFY_DONE if the notification is
+ *		considered irrelevant.
+ */
+static int idt24x_clk_notifier_cb(struct notifier_block *nb,
+				  unsigned long event, void *data)
+{
+	struct clk_notifier_data *ndata = data;
+	struct clk_idt24x_chip *chip = to_clk_idt24x_from_nb(nb);
+	int err = 0;
+
+	dev_info(&chip->i2c_client->dev,
+		 "%s: input frequency changed: %lu Hz. event: %lu",
+		 __func__, ndata->new_rate, event);
+
+	switch (event) {
+	case PRE_RATE_CHANGE: {
+		dev_dbg(&chip->i2c_client->dev, "PRE_RATE_CHANGE\n");
+		return NOTIFY_OK;
+	}
+	case POST_RATE_CHANGE:
+		chip->input_clk_freq = ndata->new_rate;
+		/*
+		 * Can't call clock API clk_set_rate here; I believe
+		 * it will be ignored if the rate is the same as we
+		 * set previously. Need to call our internal function.
+		 */
+		dev_dbg(&chip->i2c_client->dev,
+			"POST_RATE_CHANGE. Calling idt24x_set_frequency\n");
+		err = idt24x_set_frequency(chip);
+		if (err)
+			dev_err(&chip->i2c_client->dev,
+				"error calling idt24x_set_frequency (%i)\n",
+				err);
+		return NOTIFY_OK;
+	case ABORT_RATE_CHANGE:
+		return NOTIFY_OK;
+	default:
+		return NOTIFY_DONE;
+	}
+}
+
+static struct clk_hw *of_clk_idt24x_get(
+	struct of_phandle_args *clkspec, void *_data)
+{
+	struct clk_idt24x_chip *chip = _data;
+	unsigned int idx = clkspec->args[0];
+
+	if (idx >= ARRAY_SIZE(chip->clk)) {
+		pr_err("%s: invalid index %u\n", __func__, idx);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return &chip->clk[idx].hw;
+}
+
+/**
+ * idt24x_probe - main entry point for ccf driver
+ * @client:	pointer to i2c_client structure
+ * @id:		pointer to i2c_device_id structure
+ *
+ * Main entry point function that gets called to initialize the driver.
+ *
+ * Return: 0 for success.
+ */
+static int idt24x_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct clk_idt24x_chip *chip;
+	struct clk_init_data init;
+
+	int err = 0;
+	int x;
+	char buf[6];
+
+	dev_info(&client->dev, "%s", __func__);
+	chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	init.ops = &idt24x_clk_ops;
+	init.flags = 0;
+	init.num_parents = 0;
+	chip->i2c_client = client;
+
+	chip->min_freq = IDT24x_MIN_FREQ;
+	chip->max_freq = IDT24x_MAX_FREQ;
+
+	for (x = 0; x < NUM_INPUTS + 1; x++) {
+		char name[12];
+
+		sprintf(name, x == NUM_INPUTS ? "input-xtal" : "input-clk%i",
+			x);
+		dev_dbg(&client->dev, "attempting to get %s", name);
+		chip->input_clk = devm_clk_get(&client->dev, name);
+		if (IS_ERR(chip->input_clk)) {
+			err = PTR_ERR(chip->input_clk);
+			/*
+			 * TODO: Handle EPROBE_DEFER error, which indicates
+			 * that the input_clk isn't available now but may be
+			 * later when the appropriate module is loaded.
+			 */
+		} else {
+			err = 0;
+			chip->input_clk_num = x;
+			break;
+		}
+	}
+
+	if (err) {
+		dev_err(&client->dev, "Unable to get input clock (%u).", err);
+		chip->input_clk = NULL;
+		return err;
+	}
+
+	chip->input_clk_freq = clk_get_rate(chip->input_clk);
+	dev_dbg(&client->dev, "Got input-freq from input-clk in device tree: %uHz",
+		chip->input_clk_freq);
+
+	chip->input_clk_nb.notifier_call = idt24x_clk_notifier_cb;
+	if (clk_notifier_register(chip->input_clk, &chip->input_clk_nb))
+		dev_warn(&client->dev,
+			 "Unable to register clock notifier for input_clk.");
+
+	dev_dbg(&client->dev, "%s: about to read settings: %zu",
+		__func__, ARRAY_SIZE(chip->settings));
+
+	err = of_property_read_u8_array(
+		client->dev.of_node, "settings", chip->settings,
+		ARRAY_SIZE(chip->settings));
+	if (!err) {
+		dev_dbg(&client->dev, "settings property specified in DT");
+		chip->has_settings = true;
+	} else {
+		if (err == -EOVERFLOW) {
+			dev_alert(&client->dev,
+				  "EOVERFLOW error trying to read the settings. ARRAY_SIZE: %zu",
+				  ARRAY_SIZE(chip->settings));
+			return err;
+		}
+		dev_dbg(&client->dev,
+			"settings property not specified in DT (or there was an error that can be ignored: %i). The settings property is optional.",
+			err);
+	}
+
+	/*
+	 * Requested output frequencies cannot be specified in the DT.
+	 * Either a consumer needs to use the clock API to request the rate,
+	 * or use debugfs to set the rate from user space. Use clock-names in
+	 * DT to specify the output clock.
+	 */
+
+	chip->regmap = devm_regmap_init_i2c(client, &idt24x_regmap_config);
+	if (IS_ERR(chip->regmap)) {
+		dev_err(&client->dev, "failed to allocate register map\n");
+		return PTR_ERR(chip->regmap);
+	}
+
+	dev_dbg(&client->dev, "%s: call i2c_set_clientdata", __func__);
+	i2c_set_clientdata(client, chip);
+
+	if (chip->has_settings) {
+		/*
+		 * A raw settings array was specified in the DT. Write the
+		 * settings to the device immediately.
+		 */
+		err = i2cwritebulk(
+			chip->i2c_client, chip->regmap, 0, chip->settings,
+			ARRAY_SIZE(chip->settings));
+		if (err) {
+			dev_err(&client->dev,
+				"error writing all settings to chip (%i)\n",
+				err);
+			return err;
+		}
+		dev_dbg(&client->dev, "successfully wrote full settings array");
+	}
+
+	/*
+	 * Whether or not settings were written to the device, read all
+	 * current values from the hw.
+	 */
+	dev_dbg(&client->dev, "read from HW");
+	err = idt24x_read_from_hw(chip);
+	if (err) {
+		dev_err(&client->dev,
+			"failed calling idt24x_read_from_hw (%i)\n", err);
+		return err;
+	}
+
+	/* Create all 4 clocks */
+	for (x = 0; x < NUM_OUTPUTS; x++) {
+		init.name = kasprintf(
+			GFP_KERNEL, "%s.Q%i", client->dev.of_node->name, x);
+		chip->clk[x].chip = chip;
+		chip->clk[x].hw.init = &init;
+		chip->clk[x].index = x;
+		err = devm_clk_hw_register(&client->dev, &chip->clk[x].hw);
+		kfree(init.name); /* clock framework made a copy of the name */
+		if (err) {
+			dev_err(&client->dev, "clock registration failed\n");
+			return err;
+		}
+		dev_dbg(&client->dev, "successfully registered Q%i", x);
+	}
+
+	if (err) {
+		dev_err(&client->dev, "clock registration failed\n");
+		return err;
+	}
+
+	err = of_clk_add_hw_provider(
+		client->dev.of_node, of_clk_idt24x_get, chip);
+	if (err) {
+		dev_err(&client->dev, "unable to add clk provider\n");
+		return err;
+	}
+
+	err = idt24x_expose_via_debugfs(client, chip);
+	if (err) {
+		dev_err(&client->dev,
+			"error calling idt24x_expose_via_debugfs: %i\n", err);
+		return err;
+	}
+
+	if (chip->input_clk_num == NUM_INPUTS)
+		sprintf(buf, "XTAL");
+	else
+		sprintf(buf, "CLK%i", chip->input_clk_num);
+	dev_info(&client->dev, "probe success. input freq: %uHz (%s), settings string? %s\n",
+		 chip->input_clk_freq, buf,
+		 chip->has_settings ? "true" : "false");
+	return 0;
+}
+
+static int idt24x_remove(struct i2c_client *client)
+{
+	struct clk_idt24x_chip *chip = to_clk_idt24x_from_client(&client);
+
+	dev_info(&client->dev, "%s", __func__);
+	of_clk_del_provider(client->dev.of_node);
+	idt24x_cleanup_debugfs(chip);
+
+	if (!chip->input_clk)
+		clk_notifier_unregister(
+			chip->input_clk, &chip->input_clk_nb);
+	return 0;
+}
+
+static const struct i2c_device_id idt24x_id[] = {
+	{ "idt8t49n24x", idt24x },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, idt24x_id);
+
+static const struct of_device_id idt24x_of_match[] = {
+	{ .compatible = "idt,idt8t49n241" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, idt24x_of_match);
+
+static struct i2c_driver idt24x_driver = {
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table = idt24x_of_match,
+	},
+	.probe = idt24x_probe,
+	.remove = idt24x_remove,
+	.id_table = idt24x_id,
+};
+
+module_i2c_driver(idt24x_driver);
+
+MODULE_DESCRIPTION("8T49N24x ccf driver");
+MODULE_AUTHOR("David Cater <david.cater@idt.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/Kconfig
@@ -96,5 +96,6 @@
 	depends on (ARCH_MXC && ARM64) || COMPILE_TEST
 	depends on IMX_SCU && HAVE_ARM_SMCCC
 	select MXC_CLK_SCU
+	select MXC_CLK
 	help
 	  Build the driver for IMX8QXP SCU based clocks.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-composite-8m.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-composite-8m.c
@@ -97,7 +97,7 @@
 	int prediv_value;
 	int div_value;
 	int ret;
-	u32 val;
+	u32 orig, val;
 
 	ret = imx8m_clk_composite_compute_dividers(rate, parent_rate,
 						&prediv_value, &div_value);
@@ -106,13 +106,15 @@
 
 	spin_lock_irqsave(divider->lock, flags);
 
-	val = readl(divider->reg);
-	val &= ~((clk_div_mask(divider->width) << divider->shift) |
-			(clk_div_mask(PCG_DIV_WIDTH) << PCG_DIV_SHIFT));
+	orig = readl(divider->reg);
+	val = orig & ~((clk_div_mask(divider->width) << divider->shift) |
+		       (clk_div_mask(PCG_DIV_WIDTH) << PCG_DIV_SHIFT));
 
 	val |= (u32)(prediv_value  - 1) << divider->shift;
 	val |= (u32)(div_value - 1) << PCG_DIV_SHIFT;
-	writel(val, divider->reg);
+
+	if (val != orig)
+		writel(val, divider->reg);
 
 	spin_unlock_irqrestore(divider->lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx6sx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx6sx.c
@@ -280,13 +280,13 @@
 	hws[IMX6SX_CLK_SSI3_SEL]           = imx_clk_hw_mux("ssi3_sel",         base + 0x1c,  14,     2,      ssi_sels,          ARRAY_SIZE(ssi_sels));
 	hws[IMX6SX_CLK_SSI2_SEL]           = imx_clk_hw_mux("ssi2_sel",         base + 0x1c,  12,     2,      ssi_sels,          ARRAY_SIZE(ssi_sels));
 	hws[IMX6SX_CLK_SSI1_SEL]           = imx_clk_hw_mux("ssi1_sel",         base + 0x1c,  10,     2,      ssi_sels,          ARRAY_SIZE(ssi_sels));
-	hws[IMX6SX_CLK_QSPI1_SEL]          = imx_clk_hw_mux_flags("qspi1_sel", base + 0x1c,  7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels), CLK_SET_RATE_PARENT);
+	hws[IMX6SX_CLK_QSPI1_SEL]          = imx_clk_hw_mux("qspi1_sel",        base + 0x1c,  7,      3,      qspi1_sels,        ARRAY_SIZE(qspi1_sels));
 	hws[IMX6SX_CLK_PERCLK_SEL]         = imx_clk_hw_mux("perclk_sel",       base + 0x1c,  6,      1,      perclk_sels,       ARRAY_SIZE(perclk_sels));
 	hws[IMX6SX_CLK_VID_SEL]            = imx_clk_hw_mux("vid_sel",          base + 0x20,  21,     3,      vid_sels,          ARRAY_SIZE(vid_sels));
 	hws[IMX6SX_CLK_ESAI_SEL]           = imx_clk_hw_mux("esai_sel",         base + 0x20,  19,     2,      audio_sels,        ARRAY_SIZE(audio_sels));
 	hws[IMX6SX_CLK_CAN_SEL]            = imx_clk_hw_mux("can_sel",          base + 0x20,  8,      2,      can_sels,          ARRAY_SIZE(can_sels));
 	hws[IMX6SX_CLK_UART_SEL]           = imx_clk_hw_mux("uart_sel",         base + 0x24,  6,      1,      uart_sels,         ARRAY_SIZE(uart_sels));
-	hws[IMX6SX_CLK_QSPI2_SEL]          = imx_clk_hw_mux_flags("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels), CLK_SET_RATE_PARENT);
+	hws[IMX6SX_CLK_QSPI2_SEL]          = imx_clk_hw_mux("qspi2_sel",        base + 0x2c,  15,     3,      qspi2_sels,        ARRAY_SIZE(qspi2_sels));
 	hws[IMX6SX_CLK_SPDIF_SEL]          = imx_clk_hw_mux("spdif_sel",        base + 0x30,  20,     2,      audio_sels,        ARRAY_SIZE(audio_sels));
 	hws[IMX6SX_CLK_AUDIO_SEL]          = imx_clk_hw_mux("audio_sel",        base + 0x30,  7,      2,      audio_sels,        ARRAY_SIZE(audio_sels));
 	hws[IMX6SX_CLK_ENET_PRE_SEL]       = imx_clk_hw_mux("enet_pre_sel",     base + 0x34,  15,     3,      enet_pre_sels,     ARRAY_SIZE(enet_pre_sels));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx6ul.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx6ul.c
@@ -161,7 +161,6 @@
 	hws[IMX6UL_PLL5_BYPASS] = imx_clk_hw_mux_flags("pll5_bypass", base + 0xa0, 16, 1, pll5_bypass_sels, ARRAY_SIZE(pll5_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX6UL_PLL6_BYPASS] = imx_clk_hw_mux_flags("pll6_bypass", base + 0xe0, 16, 1, pll6_bypass_sels, ARRAY_SIZE(pll6_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX6UL_PLL7_BYPASS] = imx_clk_hw_mux_flags("pll7_bypass", base + 0x20, 16, 1, pll7_bypass_sels, ARRAY_SIZE(pll7_bypass_sels), CLK_SET_RATE_PARENT);
-	hws[IMX6UL_CLK_CSI_SEL] = imx_clk_hw_mux_flags("csi_sel", base + 0x3c, 9, 2, csi_sels, ARRAY_SIZE(csi_sels), CLK_SET_RATE_PARENT);
 
 	/* Do not bypass PLLs initially */
 	clk_set_parent(hws[IMX6UL_PLL1_BYPASS]->clk, hws[IMX6UL_CLK_PLL1]->clk);
@@ -270,6 +269,7 @@
 	hws[IMX6UL_CLK_ECSPI_SEL]	  = imx_clk_hw_mux("ecspi_sel",	base + 0x38, 18, 1, ecspi_sels, ARRAY_SIZE(ecspi_sels));
 	hws[IMX6UL_CLK_LCDIF_PRE_SEL]	  = imx_clk_hw_mux_flags("lcdif_pre_sel", base + 0x38, 15, 3, lcdif_pre_sels, ARRAY_SIZE(lcdif_pre_sels), CLK_SET_RATE_PARENT);
 	hws[IMX6UL_CLK_LCDIF_SEL]	  = imx_clk_hw_mux("lcdif_sel",	base + 0x38, 9, 3, lcdif_sels, ARRAY_SIZE(lcdif_sels));
+	hws[IMX6UL_CLK_CSI_SEL]		  = imx_clk_hw_mux("csi_sel", base + 0x3c, 9, 2, csi_sels, ARRAY_SIZE(csi_sels));
 
 	hws[IMX6UL_CLK_LDB_DI0_DIV_SEL]  = imx_clk_hw_mux("ldb_di0", base + 0x20, 10, 1, ldb_di0_div_sels, ARRAY_SIZE(ldb_di0_div_sels));
 	hws[IMX6UL_CLK_LDB_DI1_DIV_SEL]  = imx_clk_hw_mux("ldb_di1", base + 0x20, 11, 1, ldb_di1_div_sels, ARRAY_SIZE(ldb_di1_div_sels));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx7d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx7d.c
@@ -498,9 +498,9 @@
 	hws[IMX7D_ENET_AXI_ROOT_SRC] = imx_clk_hw_mux2_flags("enet_axi_src", base + 0x8900, 24, 3, enet_axi_sel, ARRAY_SIZE(enet_axi_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_NAND_USDHC_BUS_ROOT_SRC] = imx_clk_hw_mux2_flags("nand_usdhc_src", base + 0x8980, 24, 3, nand_usdhc_bus_sel, ARRAY_SIZE(nand_usdhc_bus_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_DRAM_PHYM_ROOT_SRC] = imx_clk_hw_mux2_flags("dram_phym_src", base + 0x9800, 24, 1, dram_phym_sel, ARRAY_SIZE(dram_phym_sel), CLK_SET_PARENT_GATE);
-	hws[IMX7D_DRAM_ROOT_SRC] = imx_clk_hw_mux2_flags("dram_src", base + 0x9880, 24, 1, dram_sel, ARRAY_SIZE(dram_sel), CLK_SET_PARENT_GATE);
+	hws[IMX7D_DRAM_ROOT_SRC] = imx_clk_hw_mux2("dram_src", base + 0x9880, 24, 1, dram_sel, ARRAY_SIZE(dram_sel));
 	hws[IMX7D_DRAM_PHYM_ALT_ROOT_SRC] = imx_clk_hw_mux2_flags("dram_phym_alt_src", base + 0xa000, 24, 3, dram_phym_alt_sel, ARRAY_SIZE(dram_phym_alt_sel), CLK_SET_PARENT_GATE);
-	hws[IMX7D_DRAM_ALT_ROOT_SRC]  = imx_clk_hw_mux2_flags("dram_alt_src", base + 0xa080, 24, 3, dram_alt_sel, ARRAY_SIZE(dram_alt_sel), CLK_SET_PARENT_GATE);
+	hws[IMX7D_DRAM_ALT_ROOT_SRC]  = imx_clk_hw_mux2("dram_alt_src", base + 0xa080, 24, 3, dram_alt_sel, ARRAY_SIZE(dram_alt_sel));
 	hws[IMX7D_USB_HSIC_ROOT_SRC] = imx_clk_hw_mux2_flags("usb_hsic_src", base + 0xa100, 24, 3, usb_hsic_sel, ARRAY_SIZE(usb_hsic_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_PCIE_CTRL_ROOT_SRC] = imx_clk_hw_mux2_flags("pcie_ctrl_src", base + 0xa180, 24, 3, pcie_ctrl_sel, ARRAY_SIZE(pcie_ctrl_sel), CLK_SET_PARENT_GATE);
 	hws[IMX7D_PCIE_PHY_ROOT_SRC] = imx_clk_hw_mux2_flags("pcie_phy_src", base + 0xa200, 24, 3, pcie_phy_sel, ARRAY_SIZE(pcie_phy_sel), CLK_SET_PARENT_GATE);
@@ -849,7 +849,6 @@
 	hws[IMX7D_WDOG4_ROOT_CLK] = imx_clk_hw_gate4("wdog4_root_clk", "wdog_post_div", base + 0x49f0, 0);
 	hws[IMX7D_KPP_ROOT_CLK] = imx_clk_hw_gate4("kpp_root_clk", "ipg_root_clk", base + 0x4aa0, 0);
 	hws[IMX7D_CSI_MCLK_ROOT_CLK] = imx_clk_hw_gate4("csi_mclk_root_clk", "csi_mclk_post_div", base + 0x4490, 0);
-	hws[IMX7D_AUDIO_MCLK_ROOT_CLK] = imx_clk_hw_gate4("audio_mclk_root_clk", "audio_mclk_post_div", base + 0x4790, 0);
 	hws[IMX7D_WRCLK_ROOT_CLK] = imx_clk_hw_gate4("wrclk_root_clk", "wrclk_post_div", base + 0x47a0, 0);
 	hws[IMX7D_USB_CTRL_CLK] = imx_clk_hw_gate4("usb_ctrl_clk", "ahb_root_clk", base + 0x4680, 0);
 	hws[IMX7D_USB_PHY1_CLK] = imx_clk_hw_gate4("usb_phy1_clk", "pll_usb1_main_clk", base + 0x46a0, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx8mn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx8mn.c
@@ -30,7 +30,7 @@
 static const char * const video_pll1_bypass_sels[] = {"video_pll1", "video_pll1_ref_sel", };
 static const char * const dram_pll_bypass_sels[] = {"dram_pll", "dram_pll_ref_sel", };
 static const char * const gpu_pll_bypass_sels[] = {"gpu_pll", "gpu_pll_ref_sel", };
-static const char * const vpu_pll_bypass_sels[] = {"vpu_pll", "vpu_pll_ref_sel", };
+static const char * const m7_alt_pll_bypass_sels[] = {"m7_alt_pll", "m7_alt_pll_ref_sel", };
 static const char * const arm_pll_bypass_sels[] = {"arm_pll", "arm_pll_ref_sel", };
 static const char * const sys_pll3_bypass_sels[] = {"sys_pll3", "sys_pll3_ref_sel", };
 
@@ -40,7 +40,7 @@
 
 static const char * const imx8mn_a53_core_sels[] = {"arm_a53_div", "arm_pll_out", };
 
-static const char * const imx8mn_m7_sels[] = {"osc_24m", "sys_pll2_200m", "sys_pll2_250m", "vpu_pll_out",
+static const char * const imx8mn_m7_sels[] = {"osc_24m", "sys_pll2_200m", "sys_pll2_250m", "m7_alt_pll_out",
 				       "sys_pll1_800m", "audio_pll1_out", "video_pll1_out", "sys_pll3_out", };
 
 static const char * const imx8mn_gpu_core_sels[] = {"osc_24m", "gpu_pll_out", "sys_pll1_800m",
@@ -108,27 +108,27 @@
 						      "sys_pll3_out", "clk_ext4", };
 
 static const char * const imx8mn_sai2_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
-						"clk_ext3", "clk_ext4", };
+						"video_pll1_out", "sys_pll1_133m", "dummy",
+						"clk_ext2", "clk_ext3", };
 
 static const char * const imx8mn_sai3_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_sai5_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext2", "clk_ext3", };
 
 static const char * const imx8mn_sai6_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_sai7_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						"video_pll1_out", "sys_pll1_133m", "dummy",
 						"clk_ext3", "clk_ext4", };
 
 static const char * const imx8mn_spdif1_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						  "video_pll1_out", "sys_pll1_133m", "osc_hdmi",
+						  "video_pll1_out", "sys_pll1_133m", "dummy",
 						  "clk_ext2", "clk_ext3", };
 
 static const char * const imx8mn_enet_ref_sels[] = {"osc_24m", "sys_pll2_125m", "sys_pll2_50m",
@@ -140,8 +140,8 @@
 						      "clk_ext4", "video_pll1_out", };
 
 static const char * const imx8mn_enet_phy_sels[] = {"osc_24m", "sys_pll2_50m", "sys_pll2_125m",
-						    "sys_pll2_200m", "sys_pll2_500m", "video_pll1_out",
-						    "audio_pll2_out", };
+						    "sys_pll2_200m", "sys_pll2_500m", "audio_pll1_out",
+						    "video_pll_out", "audio_pll2_out", };
 
 static const char * const imx8mn_nand_sels[] = {"osc_24m", "sys_pll2_500m", "audio_pll1_out",
 						"sys_pll1_400m", "audio_pll2_out", "sys_pll3_out",
@@ -228,10 +228,10 @@
 						"sys_pll1_80m", "video_pll1_out", };
 
 static const char * const imx8mn_wdog_sels[] = {"osc_24m", "sys_pll1_133m", "sys_pll1_160m",
-						"vpu_pll_out", "sys_pll2_125m", "sys_pll3_out",
+						"m7_alt_pll_out", "sys_pll2_125m", "sys_pll3_out",
 						"sys_pll1_80m", "sys_pll2_166m", };
 
-static const char * const imx8mn_wrclk_sels[] = {"osc_24m", "sys_pll1_40m", "vpu_pll_out",
+static const char * const imx8mn_wrclk_sels[] = {"osc_24m", "sys_pll1_40m", "m7_alt_pll_out",
 						 "sys_pll3_out", "sys_pll2_200m", "sys_pll1_266m",
 						 "sys_pll2_500m", "sys_pll1_100m", };
 
@@ -277,9 +277,9 @@
 
 static const char * const imx8mn_dram_core_sels[] = {"dram_pll_out", "dram_alt_root", };
 
-static const char * const imx8mn_clko1_sels[] = {"osc_24m", "sys_pll1_800m", "osc_27m",
-						 "sys_pll1_200m", "audio_pll2_out", "vpu_pll",
-						 "sys_pll1_80m", };
+static const char * const imx8mn_clko1_sels[] = {"osc_24m", "sys_pll1_800m", "dummy",
+						 "sys_pll1_200m", "audio_pll2_out", "sys_pll2_500m",
+						 "dummy", "sys_pll1_80m", };
 static const char * const imx8mn_clko2_sels[] = {"osc_24m", "sys_pll2_200m", "sys_pll1_400m",
 						 "sys_pll2_166m", "sys_pll3_out", "audio_pll1_out",
 						 "video_pll1_out", "osc_32k", };
@@ -299,7 +299,7 @@
 	void __iomem *base;
 	int ret;
 
-	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
+	clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws,
 					  IMX8MN_CLK_END), GFP_KERNEL);
 	if (WARN_ON(!clk_hw_data))
 		return -ENOMEM;
@@ -316,10 +316,10 @@
 	hws[IMX8MN_CLK_EXT4] = imx_obtain_fixed_clk_hw(np, "clk_ext4");
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mn-anatop");
-	base = of_iomap(np, 0);
+	base = devm_of_iomap(dev, np, 0, NULL);
 	of_node_put(np);
-	if (WARN_ON(!base)) {
-		ret = -ENOMEM;
+	if (WARN_ON(IS_ERR(base))) {
+		ret = PTR_ERR(base);
 		goto unregister_hws;
 	}
 
@@ -328,7 +328,7 @@
 	hws[IMX8MN_VIDEO_PLL1_REF_SEL] = imx_clk_hw_mux("video_pll1_ref_sel", base + 0x28, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_DRAM_PLL_REF_SEL] = imx_clk_hw_mux("dram_pll_ref_sel", base + 0x50, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_GPU_PLL_REF_SEL] = imx_clk_hw_mux("gpu_pll_ref_sel", base + 0x64, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
-	hws[IMX8MN_VPU_PLL_REF_SEL] = imx_clk_hw_mux("vpu_pll_ref_sel", base + 0x74, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
+	hws[IMX8MN_M7_ALT_PLL_REF_SEL] = imx_clk_hw_mux("m7_alt_pll_ref_sel", base + 0x74, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_ARM_PLL_REF_SEL] = imx_clk_hw_mux("arm_pll_ref_sel", base + 0x84, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MN_SYS_PLL3_REF_SEL] = imx_clk_hw_mux("sys_pll3_ref_sel", base + 0x114, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 
@@ -337,7 +337,7 @@
 	hws[IMX8MN_VIDEO_PLL1] = imx_clk_hw_pll14xx("video_pll1", "video_pll1_ref_sel", base + 0x28, &imx_1443x_pll);
 	hws[IMX8MN_DRAM_PLL] = imx_clk_hw_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_dram_pll);
 	hws[IMX8MN_GPU_PLL] = imx_clk_hw_pll14xx("gpu_pll", "gpu_pll_ref_sel", base + 0x64, &imx_1416x_pll);
-	hws[IMX8MN_VPU_PLL] = imx_clk_hw_pll14xx("vpu_pll", "vpu_pll_ref_sel", base + 0x74, &imx_1416x_pll);
+	hws[IMX8MN_M7_ALT_PLL] = imx_clk_hw_pll14xx("m7_alt_pll", "m7_alt_pll_ref_sel", base + 0x74, &imx_1416x_pll);
 	hws[IMX8MN_ARM_PLL] = imx_clk_hw_pll14xx("arm_pll", "arm_pll_ref_sel", base + 0x84, &imx_1416x_pll);
 	hws[IMX8MN_SYS_PLL1] = imx_clk_hw_fixed("sys_pll1", 800000000);
 	hws[IMX8MN_SYS_PLL2] = imx_clk_hw_fixed("sys_pll2", 1000000000);
@@ -349,7 +349,7 @@
 	hws[IMX8MN_VIDEO_PLL1_BYPASS] = imx_clk_hw_mux_flags("video_pll1_bypass", base + 0x28, 16, 1, video_pll1_bypass_sels, ARRAY_SIZE(video_pll1_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_DRAM_PLL_BYPASS] = imx_clk_hw_mux_flags("dram_pll_bypass", base + 0x50, 16, 1, dram_pll_bypass_sels, ARRAY_SIZE(dram_pll_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_GPU_PLL_BYPASS] = imx_clk_hw_mux_flags("gpu_pll_bypass", base + 0x64, 28, 1, gpu_pll_bypass_sels, ARRAY_SIZE(gpu_pll_bypass_sels), CLK_SET_RATE_PARENT);
-	hws[IMX8MN_VPU_PLL_BYPASS] = imx_clk_hw_mux_flags("vpu_pll_bypass", base + 0x74, 28, 1, vpu_pll_bypass_sels, ARRAY_SIZE(vpu_pll_bypass_sels), CLK_SET_RATE_PARENT);
+	hws[IMX8MN_M7_ALT_PLL_BYPASS] = imx_clk_hw_mux_flags("m7_alt_pll_bypass", base + 0x74, 28, 1, m7_alt_pll_bypass_sels, ARRAY_SIZE(m7_alt_pll_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_ARM_PLL_BYPASS] = imx_clk_hw_mux_flags("arm_pll_bypass", base + 0x84, 28, 1, arm_pll_bypass_sels, ARRAY_SIZE(arm_pll_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX8MN_SYS_PLL3_BYPASS] = imx_clk_hw_mux_flags("sys_pll3_bypass", base + 0x114, 28, 1, sys_pll3_bypass_sels, ARRAY_SIZE(sys_pll3_bypass_sels), CLK_SET_RATE_PARENT);
 
@@ -359,7 +359,7 @@
 	hws[IMX8MN_VIDEO_PLL1_OUT] = imx_clk_hw_gate("video_pll1_out", "video_pll1_bypass", base + 0x28, 13);
 	hws[IMX8MN_DRAM_PLL_OUT] = imx_clk_hw_gate("dram_pll_out", "dram_pll_bypass", base + 0x50, 13);
 	hws[IMX8MN_GPU_PLL_OUT] = imx_clk_hw_gate("gpu_pll_out", "gpu_pll_bypass", base + 0x64, 11);
-	hws[IMX8MN_VPU_PLL_OUT] = imx_clk_hw_gate("vpu_pll_out", "vpu_pll_bypass", base + 0x74, 11);
+	hws[IMX8MN_M7_ALT_PLL_OUT] = imx_clk_hw_gate("m7_alt_pll_out", "m7_alt_pll_bypass", base + 0x74, 11);
 	hws[IMX8MN_ARM_PLL_OUT] = imx_clk_hw_gate("arm_pll_out", "arm_pll_bypass", base + 0x84, 11);
 	hws[IMX8MN_SYS_PLL3_OUT] = imx_clk_hw_gate("sys_pll3_out", "sys_pll3_bypass", base + 0x114, 11);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx8mp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx8mp.c
@@ -17,6 +17,7 @@
 
 static u32 share_count_nand;
 static u32 share_count_media;
+static u32 share_count_usb;
 
 static const char * const pll_ref_sels[] = { "osc_24m", "dummy", "dummy", "dummy", };
 static const char * const audio_pll1_bypass_sels[] = {"audio_pll1", "audio_pll1_ref_sel", };
@@ -176,10 +177,6 @@
 						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
 						"clk_ext3", "clk_ext4", };
 
-static const char * const imx8mp_sai4_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
-						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
-						"clk_ext1", "clk_ext2", };
-
 static const char * const imx8mp_sai5_sels[] = {"osc_24m", "audio_pll1_out", "audio_pll2_out",
 						"video_pll1_out", "sys_pll1_133m", "osc_hdmi",
 						"clk_ext2", "clk_ext3", };
@@ -358,7 +355,7 @@
 							       "clk_ext2", "audio_pll2_out",
 							       "video_pll1_out", };
 
-static const char * const imx8mp_media_disp1_pix_sels[] = {"osc_24m", "video_pll1_out", "audio_pll2_out",
+static const char * const imx8mp_media_disp_pix_sels[] = {"osc_24m", "video_pll1_out", "audio_pll2_out",
 							   "audio_pll1_out", "sys_pll1_800m",
 							   "sys_pll2_1000m", "sys_pll3_out", "clk_ext4", };
 
@@ -399,6 +396,12 @@
 
 static const char * const imx8mp_dram_core_sels[] = {"dram_pll_out", "dram_alt_root", };
 
+static const char * const imx8mp_clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "video_pll1_out",
+						  "dummy", "dummy", "gpu_pll_out", "vpu_pll_out",
+						  "arm_pll_out", "sys_pll1_out", "sys_pll2_out",
+						  "sys_pll3_out", "dummy", "dummy", "osc_24m",
+						  "dummy", "osc_32k"};
+
 static struct clk_hw **hws;
 static struct clk_hw_onecell_data *clk_hw_data;
 
@@ -407,25 +410,22 @@
 	struct device *dev = &pdev->dev;
 	struct device_node *np;
 	void __iomem *anatop_base, *ccm_base;
+	int err;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
-	anatop_base = of_iomap(np, 0);
+	anatop_base = devm_of_iomap(dev, np, 0, NULL);
 	of_node_put(np);
-	if (WARN_ON(!anatop_base))
-		return -ENOMEM;
+	if (WARN_ON(IS_ERR(anatop_base)))
+		return PTR_ERR(anatop_base);
 
 	np = dev->of_node;
 	ccm_base = devm_platform_ioremap_resource(pdev, 0);
-	if (WARN_ON(IS_ERR(ccm_base))) {
-		iounmap(anatop_base);
+	if (WARN_ON(IS_ERR(ccm_base)))
 		return PTR_ERR(ccm_base);
-	}
 
-	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws, IMX8MP_CLK_END), GFP_KERNEL);
-	if (WARN_ON(!clk_hw_data)) {
-		iounmap(anatop_base);
+	clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws, IMX8MP_CLK_END), GFP_KERNEL);
+	if (WARN_ON(!clk_hw_data))
 		return -ENOMEM;
-	}
 
 	clk_hw_data->num = IMX8MP_CLK_END;
 	hws = clk_hw_data->hws;
@@ -520,6 +520,15 @@
 	hws[IMX8MP_SYS_PLL2_500M] = imx_clk_hw_fixed_factor("sys_pll2_500m", "sys_pll2_500m_cg", 1, 2);
 	hws[IMX8MP_SYS_PLL2_1000M] = imx_clk_hw_fixed_factor("sys_pll2_1000m", "sys_pll2_out", 1, 1);
 
+	hws[IMX8MP_CLK_CLKOUT1_SEL] = imx_clk_hw_mux2("clkout1_sel", anatop_base + 0x128, 4, 4,
+						      imx8mp_clkout_sels, ARRAY_SIZE(imx8mp_clkout_sels));
+	hws[IMX8MP_CLK_CLKOUT1_DIV] = imx_clk_hw_divider("clkout1_div", "clkout1_sel", anatop_base + 0x128, 0, 4);
+	hws[IMX8MP_CLK_CLKOUT1] = imx_clk_hw_gate("clkout1", "clkout1_div", anatop_base + 0x128, 8);
+	hws[IMX8MP_CLK_CLKOUT2_SEL] = imx_clk_hw_mux2("clkout2_sel", anatop_base + 0x128, 20, 4,
+						      imx8mp_clkout_sels, ARRAY_SIZE(imx8mp_clkout_sels));
+	hws[IMX8MP_CLK_CLKOUT2_DIV] = imx_clk_hw_divider("clkout2_div", "clkout2_sel", anatop_base + 0x128, 16, 4);
+	hws[IMX8MP_CLK_CLKOUT2] = imx_clk_hw_gate("clkout2", "clkout2_div", anatop_base + 0x128, 24);
+
 	hws[IMX8MP_CLK_A53_DIV] = imx8m_clk_hw_composite_core("arm_a53_div", imx8mp_a53_sels, ccm_base + 0x8000);
 	hws[IMX8MP_CLK_A53_SRC] = hws[IMX8MP_CLK_A53_DIV];
 	hws[IMX8MP_CLK_A53_CG] = hws[IMX8MP_CLK_A53_DIV];
@@ -554,11 +563,12 @@
 	hws[IMX8MP_CLK_AHB] = imx8m_clk_hw_composite_bus_critical("ahb_root", imx8mp_ahb_sels, ccm_base + 0x9000);
 	hws[IMX8MP_CLK_AUDIO_AHB] = imx8m_clk_hw_composite_bus("audio_ahb", imx8mp_audio_ahb_sels, ccm_base + 0x9100);
 	hws[IMX8MP_CLK_MIPI_DSI_ESC_RX] = imx8m_clk_hw_composite_bus("mipi_dsi_esc_rx", imx8mp_mipi_dsi_esc_rx_sels, ccm_base + 0x9200);
+	hws[IMX8MP_CLK_MEDIA_DISP2_PIX] = imx8m_clk_hw_composite("media_disp2_pix", imx8mp_media_disp_pix_sels, ccm_base + 0x9300);
 
 	hws[IMX8MP_CLK_IPG_ROOT] = imx_clk_hw_divider2("ipg_root", "ahb_root", ccm_base + 0x9080, 0, 1);
 
-	hws[IMX8MP_CLK_DRAM_ALT] = imx8m_clk_hw_composite("dram_alt", imx8mp_dram_alt_sels, ccm_base + 0xa000);
-	hws[IMX8MP_CLK_DRAM_APB] = imx8m_clk_hw_composite_critical("dram_apb", imx8mp_dram_apb_sels, ccm_base + 0xa080);
+	hws[IMX8MP_CLK_DRAM_ALT] = imx8m_clk_hw_fw_managed_composite("dram_alt", imx8mp_dram_alt_sels, ccm_base + 0xa000);
+	hws[IMX8MP_CLK_DRAM_APB] = imx8m_clk_hw_fw_managed_composite_critical("dram_apb", imx8mp_dram_apb_sels, ccm_base + 0xa080);
 	hws[IMX8MP_CLK_VPU_G1] = imx8m_clk_hw_composite("vpu_g1", imx8mp_vpu_g1_sels, ccm_base + 0xa100);
 	hws[IMX8MP_CLK_VPU_G2] = imx8m_clk_hw_composite("vpu_g2", imx8mp_vpu_g2_sels, ccm_base + 0xa180);
 	hws[IMX8MP_CLK_CAN1] = imx8m_clk_hw_composite("can1", imx8mp_can1_sels, ccm_base + 0xa200);
@@ -569,7 +579,6 @@
 	hws[IMX8MP_CLK_SAI1] = imx8m_clk_hw_composite("sai1", imx8mp_sai1_sels, ccm_base + 0xa580);
 	hws[IMX8MP_CLK_SAI2] = imx8m_clk_hw_composite("sai2", imx8mp_sai2_sels, ccm_base + 0xa600);
 	hws[IMX8MP_CLK_SAI3] = imx8m_clk_hw_composite("sai3", imx8mp_sai3_sels, ccm_base + 0xa680);
-	hws[IMX8MP_CLK_SAI4] = imx8m_clk_hw_composite("sai4", imx8mp_sai4_sels, ccm_base + 0xa700);
 	hws[IMX8MP_CLK_SAI5] = imx8m_clk_hw_composite("sai5", imx8mp_sai5_sels, ccm_base + 0xa780);
 	hws[IMX8MP_CLK_SAI6] = imx8m_clk_hw_composite("sai6", imx8mp_sai6_sels, ccm_base + 0xa800);
 	hws[IMX8MP_CLK_ENET_QOS] = imx8m_clk_hw_composite("enet_qos", imx8mp_enet_qos_sels, ccm_base + 0xa880);
@@ -616,7 +625,7 @@
 	hws[IMX8MP_CLK_USDHC3] = imx8m_clk_hw_composite("usdhc3", imx8mp_usdhc3_sels, ccm_base + 0xbc80);
 	hws[IMX8MP_CLK_MEDIA_CAM1_PIX] = imx8m_clk_hw_composite("media_cam1_pix", imx8mp_media_cam1_pix_sels, ccm_base + 0xbd00);
 	hws[IMX8MP_CLK_MEDIA_MIPI_PHY1_REF] = imx8m_clk_hw_composite("media_mipi_phy1_ref", imx8mp_media_mipi_phy1_ref_sels, ccm_base + 0xbd80);
-	hws[IMX8MP_CLK_MEDIA_DISP1_PIX] = imx8m_clk_hw_composite("media_disp1_pix", imx8mp_media_disp1_pix_sels, ccm_base + 0xbe00);
+	hws[IMX8MP_CLK_MEDIA_DISP1_PIX] = imx8m_clk_hw_composite("media_disp1_pix", imx8mp_media_disp_pix_sels, ccm_base + 0xbe00);
 	hws[IMX8MP_CLK_MEDIA_CAM2_PIX] = imx8m_clk_hw_composite("media_cam2_pix", imx8mp_media_cam2_pix_sels, ccm_base + 0xbe80);
 	hws[IMX8MP_CLK_MEDIA_LDB] = imx8m_clk_hw_composite("media_ldb", imx8mp_media_ldb_sels, ccm_base + 0xbf00);
 	hws[IMX8MP_CLK_MEMREPAIR] = imx8m_clk_hw_composite_critical("mem_repair", imx8mp_memrepair_sels, ccm_base + 0xbf80);
@@ -675,7 +684,8 @@
 	hws[IMX8MP_CLK_UART2_ROOT] = imx_clk_hw_gate4("uart2_root_clk", "uart2", ccm_base + 0x44a0, 0);
 	hws[IMX8MP_CLK_UART3_ROOT] = imx_clk_hw_gate4("uart3_root_clk", "uart3", ccm_base + 0x44b0, 0);
 	hws[IMX8MP_CLK_UART4_ROOT] = imx_clk_hw_gate4("uart4_root_clk", "uart4", ccm_base + 0x44c0, 0);
-	hws[IMX8MP_CLK_USB_ROOT] = imx_clk_hw_gate4("usb_root_clk", "osc_32k", ccm_base + 0x44d0, 0);
+	hws[IMX8MP_CLK_USB_ROOT] = imx_clk_hw_gate2_shared2("usb_root_clk", "hsio_axi", ccm_base + 0x44d0, 0, &share_count_usb);
+	hws[IMX8MP_CLK_USB_SUSP] = imx_clk_hw_gate2_shared2("usb_suspend_clk", "osc_32k", ccm_base + 0x44d0, 0, &share_count_usb);
 	hws[IMX8MP_CLK_USB_PHY_ROOT] = imx_clk_hw_gate4("usb_phy_root_clk", "usb_phy_ref", ccm_base + 0x44f0, 0);
 	hws[IMX8MP_CLK_USDHC1_ROOT] = imx_clk_hw_gate4("usdhc1_root_clk", "usdhc1", ccm_base + 0x4510, 0);
 	hws[IMX8MP_CLK_USDHC2_ROOT] = imx_clk_hw_gate4("usdhc2_root_clk", "usdhc2", ccm_base + 0x4520, 0);
@@ -710,7 +720,12 @@
 
 	imx_check_clk_hws(hws, IMX8MP_CLK_END);
 
-	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
+	err = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
+	if (err < 0) {
+		dev_err(dev, "failed to register hws for i.MX8MP\n");
+		imx_unregister_hw_clocks(hws, IMX8MP_CLK_END);
+		return err;
+	}
 
 	imx_register_uart_clocks(4);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx8mq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx8mq.c
@@ -288,8 +288,7 @@
 	void __iomem *base;
 	int err;
 
-	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
-					  IMX8MQ_CLK_END), GFP_KERNEL);
+	clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws, IMX8MQ_CLK_END), GFP_KERNEL);
 	if (WARN_ON(!clk_hw_data))
 		return -ENOMEM;
 
@@ -306,10 +305,12 @@
 	hws[IMX8MQ_CLK_EXT4] = imx_obtain_fixed_clk_hw(np, "clk_ext4");
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mq-anatop");
-	base = of_iomap(np, 0);
+	base = devm_of_iomap(dev, np, 0, NULL);
 	of_node_put(np);
-	if (WARN_ON(!base))
-		return -ENOMEM;
+	if (WARN_ON(IS_ERR(base))) {
+		err = PTR_ERR(base);
+		goto unregister_hws;
+	}
 
 	hws[IMX8MQ_ARM_PLL_REF_SEL] = imx_clk_hw_mux("arm_pll_ref_sel", base + 0x28, 16, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
 	hws[IMX8MQ_GPU_PLL_REF_SEL] = imx_clk_hw_mux("gpu_pll_ref_sel", base + 0x18, 16, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels));
@@ -395,8 +396,10 @@
 
 	np = dev->of_node;
 	base = devm_platform_ioremap_resource(pdev, 0);
-	if (WARN_ON(IS_ERR(base)))
-		return PTR_ERR(base);
+	if (WARN_ON(IS_ERR(base))) {
+		err = PTR_ERR(base);
+		goto unregister_hws;
+	}
 
 	/* CORE */
 	hws[IMX8MQ_CLK_A53_DIV] = imx8m_clk_hw_composite_core("arm_a53_div", imx8mq_a53_sels, base + 0x8000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx8qxp-lpcg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx8qxp-lpcg.c
@@ -248,7 +248,7 @@
 
 	for (i = 0; i < count; i++) {
 		idx = bit_offset[i] / 4;
-		if (idx > IMX_LPCG_MAX_CLKS) {
+		if (idx >= IMX_LPCG_MAX_CLKS) {
 			dev_warn(&pdev->dev, "invalid bit offset of clock %d\n",
 				 i);
 			ret = -EINVAL;
@@ -370,7 +370,7 @@
 	.probe = imx8qxp_lpcg_clk_probe,
 };
 
-builtin_platform_driver(imx8qxp_lpcg_clk_driver);
+module_platform_driver(imx8qxp_lpcg_clk_driver);
 
 MODULE_AUTHOR("Aisheng Dong <aisheng.dong@nxp.com>");
 MODULE_DESCRIPTION("NXP i.MX8QXP LPCG clock driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-imx8qxp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-imx8qxp.c
@@ -67,6 +67,22 @@
 	"lcd_pxl_bypass_div_clk",
 };
 
+static const char *const lvds0_sels[] = {
+	"clk_dummy",
+	"clk_dummy",
+	"clk_dummy",
+	"clk_dummy",
+	"mipi0_lvds_bypass_clk",
+};
+
+static const char *const lvds1_sels[] = {
+	"clk_dummy",
+	"clk_dummy",
+	"clk_dummy",
+	"clk_dummy",
+	"mipi1_lvds_bypass_clk",
+};
+
 static const char * const mipi_sels[] = {
 	"clk_dummy",
 	"clk_dummy",
@@ -148,10 +164,10 @@
 	imx_clk_scu("adc0_clk",  IMX_SC_R_ADC_0, IMX_SC_PM_CLK_PER);
 	imx_clk_scu("adc1_clk",  IMX_SC_R_ADC_1, IMX_SC_PM_CLK_PER);
 	imx_clk_scu("pwm_clk",   IMX_SC_R_LCD_0_PWM_0, IMX_SC_PM_CLK_PER);
+	imx_clk_scu("elcdif_pll", IMX_SC_R_ELCDIF_PLL, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu2("lcd_clk", lcd_sels, ARRAY_SIZE(lcd_sels), IMX_SC_R_LCD_0, IMX_SC_PM_CLK_PER);
-	imx_clk_scu2("lcd_pxl_clk", lcd_pxl_sels, ARRAY_SIZE(lcd_pxl_sels), IMX_SC_R_LCD_0, IMX_SC_PM_CLK_MISC0);
 	imx_clk_scu("lcd_pxl_bypass_div_clk", IMX_SC_R_LCD_0, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu("elcdif_pll", IMX_SC_R_ELCDIF_PLL, IMX_SC_PM_CLK_PLL);
+	imx_clk_scu2("lcd_pxl_clk", lcd_pxl_sels, ARRAY_SIZE(lcd_pxl_sels), IMX_SC_R_LCD_0, IMX_SC_PM_CLK_MISC0);
 
 	/* Audio SS */
 	imx_clk_scu("audio_pll0_clk", IMX_SC_R_AUDIO_PLL_0, IMX_SC_PM_CLK_PLL);
@@ -184,26 +200,26 @@
 	imx_clk_scu("usb3_lpm_div", IMX_SC_R_USB_2, IMX_SC_PM_CLK_MISC);
 
 	/* Display controller SS */
-	imx_clk_scu2("dc0_disp0_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC0);
-	imx_clk_scu2("dc0_disp1_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc0_pll0_clk", IMX_SC_R_DC_0_PLL_0, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc0_pll1_clk", IMX_SC_R_DC_0_PLL_1, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc0_bypass0_clk", IMX_SC_R_DC_0_VIDEO0, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("dc0_disp0_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC0);
+	imx_clk_scu2("dc0_disp1_clk", dc0_sels, ARRAY_SIZE(dc0_sels), IMX_SC_R_DC_0, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc0_bypass1_clk", IMX_SC_R_DC_0_VIDEO1, IMX_SC_PM_CLK_BYPASS);
 
-	imx_clk_scu2("dc1_disp0_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC0);
-	imx_clk_scu2("dc1_disp1_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc1_pll0_clk", IMX_SC_R_DC_1_PLL_0, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc1_pll1_clk", IMX_SC_R_DC_1_PLL_1, IMX_SC_PM_CLK_PLL);
 	imx_clk_scu("dc1_bypass0_clk", IMX_SC_R_DC_1_VIDEO0, IMX_SC_PM_CLK_BYPASS);
+	imx_clk_scu2("dc1_disp0_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC0);
+	imx_clk_scu2("dc1_disp1_clk", dc1_sels, ARRAY_SIZE(dc1_sels), IMX_SC_R_DC_1, IMX_SC_PM_CLK_MISC1);
 	imx_clk_scu("dc1_bypass1_clk", IMX_SC_R_DC_1_VIDEO1, IMX_SC_PM_CLK_BYPASS);
 
 	/* MIPI-LVDS SS */
 	imx_clk_scu("mipi0_bypass_clk", IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_BYPASS);
 	imx_clk_scu("mipi0_pixel_clk", IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PER);
-	imx_clk_scu("mipi0_lvds_pixel_clk", IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu("mipi0_lvds_bypass_clk", IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu("mipi0_lvds_phy_clk", IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC3);
+	imx_clk_scu2("mipi0_lvds_pixel_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC2);
+	imx_clk_scu2("mipi0_lvds_phy_clk", lvds0_sels, ARRAY_SIZE(lvds0_sels), IMX_SC_R_LVDS_0, IMX_SC_PM_CLK_MISC3);
 	imx_clk_scu2("mipi0_dsi_tx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_MST_BUS);
 	imx_clk_scu2("mipi0_dsi_rx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_SLV_BUS);
 	imx_clk_scu2("mipi0_dsi_phy_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_0, IMX_SC_PM_CLK_PHY);
@@ -213,9 +229,9 @@
 
 	imx_clk_scu("mipi1_bypass_clk", IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_BYPASS);
 	imx_clk_scu("mipi1_pixel_clk", IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_PER);
-	imx_clk_scu("mipi1_lvds_pixel_clk", IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC2);
 	imx_clk_scu("mipi1_lvds_bypass_clk", IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_BYPASS);
-	imx_clk_scu("mipi1_lvds_phy_clk", IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC3);
+	imx_clk_scu2("mipi1_lvds_pixel_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC2);
+	imx_clk_scu2("mipi1_lvds_phy_clk", lvds1_sels, ARRAY_SIZE(lvds1_sels), IMX_SC_R_LVDS_1, IMX_SC_PM_CLK_MISC3);
 
 	imx_clk_scu2("mipi1_dsi_tx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_MST_BUS);
 	imx_clk_scu2("mipi1_dsi_rx_esc_clk", mipi_sels, ARRAY_SIZE(mipi_sels), IMX_SC_R_MIPI_1, IMX_SC_PM_CLK_SLV_BUS);
@@ -308,7 +324,7 @@
 	},
 	.probe = imx8qxp_clk_probe,
 };
-builtin_platform_driver(imx8qxp_clk_driver);
+module_platform_driver(imx8qxp_clk_driver);
 
 MODULE_AUTHOR("Aisheng Dong <aisheng.dong@nxp.com>");
 MODULE_DESCRIPTION("NXP i.MX8QXP clock driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-lpcg-scu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-lpcg-scu.c
@@ -6,10 +6,12 @@
 
 #include <linux/bits.h>
 #include <linux/clk-provider.h>
+#include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/units.h>
 
 #include "clk-scu.h"
 
@@ -41,6 +43,29 @@
 
 #define to_clk_lpcg_scu(_hw) container_of(_hw, struct clk_lpcg_scu, hw)
 
+/* e10858 -LPCG clock gating register synchronization errata */
+static void lpcg_e10858_writel(unsigned long rate, void __iomem *reg, u32 val)
+{
+	writel(val, reg);
+
+	if (rate >= 24 * HZ_PER_MHZ || rate == 0) {
+		/*
+		 * The time taken to access the LPCG registers from the AP core
+		 * through the interconnect is longer than the minimum delay
+		 * of 4 clock cycles required by the errata.
+		 * Adding a readl will provide sufficient delay to prevent
+		 * back-to-back writes.
+		 */
+		readl(reg);
+	} else {
+		/*
+		 * For clocks running below 24MHz, wait a minimum of
+		 * 4 clock cycles.
+		 */
+		ndelay(4 * (DIV_ROUND_UP(1000 * HZ_PER_MHZ, rate)));
+	}
+}
+
 static int clk_lpcg_scu_enable(struct clk_hw *hw)
 {
 	struct clk_lpcg_scu *clk = to_clk_lpcg_scu(hw);
@@ -57,7 +82,8 @@
 		val |= CLK_GATE_SCU_LPCG_HW_SEL;
 
 	reg |= val << clk->bit_idx;
-	writel(reg, clk->reg);
+
+	lpcg_e10858_writel(clk_hw_get_rate(hw), clk->reg, reg);
 
 	spin_unlock_irqrestore(&imx_lpcg_scu_lock, flags);
 
@@ -74,7 +100,7 @@
 
 	reg = readl_relaxed(clk->reg);
 	reg &= ~(CLK_GATE_SCU_LPCG_MASK << clk->bit_idx);
-	writel(reg, clk->reg);
+	lpcg_e10858_writel(clk_hw_get_rate(hw), clk->reg, reg);
 
 	spin_unlock_irqrestore(&imx_lpcg_scu_lock, flags);
 }
@@ -145,13 +171,8 @@
 {
 	struct clk_lpcg_scu *clk = dev_get_drvdata(dev);
 
-	/*
-	 * FIXME: Sometimes writes don't work unless the CPU issues
-	 * them twice
-	 */
-
-	writel(clk->state, clk->reg);
 	writel(clk->state, clk->reg);
+	lpcg_e10858_writel(0, clk->reg, clk->state);
 	dev_dbg(dev, "restore lpcg state 0x%x\n", clk->state);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk-scu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk-scu.c
@@ -577,7 +577,7 @@
 		clk->rate = clk_scu_recalc_rate(&clk->hw, 0);
 	else
 		clk->rate = clk_hw_get_rate(&clk->hw);
-	clk->is_enabled = clk_hw_is_enabled(&clk->hw);
+	clk->is_enabled = clk_hw_is_prepared(&clk->hw);
 
 	if (clk->parent)
 		dev_dbg(dev, "save parent %s idx %u\n", clk_hw_get_name(clk->parent),
@@ -690,7 +690,11 @@
 		pr_warn("%s: failed to attached the power domain %d\n",
 			name, ret);
 
-	platform_device_add(pdev);
+	ret = platform_device_add(pdev);
+	if (ret) {
+		platform_device_put(pdev);
+		return ERR_PTR(ret);
+	}
 
 	/* For API backwards compatiblilty, simply return NULL for success */
 	return NULL;
@@ -698,11 +702,11 @@
 
 void imx_clk_scu_unregister(void)
 {
-	struct imx_scu_clk_node *clk;
+	struct imx_scu_clk_node *clk, *n;
 	int i;
 
 	for (i = 0; i < IMX_SC_R_LAST; i++) {
-		list_for_each_entry(clk, &imx_scu_clks[i], node) {
+		list_for_each_entry_safe(clk, n, &imx_scu_clks[i], node) {
 			clk_hw_unregister(clk->hw);
 			kfree(clk);
 		}
@@ -837,8 +841,10 @@
 	if (!clk_node)
 		return ERR_PTR(-ENOMEM);
 
-	if (!imx_scu_clk_is_valid(rsrc_id))
+	if (!imx_scu_clk_is_valid(rsrc_id)) {
+		kfree(clk_node);
 		return ERR_PTR(-EINVAL);
+	}
 
 	clk = kzalloc(sizeof(*clk), GFP_KERNEL);
 	if (!clk) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/imx/clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/imx/clk.c
@@ -201,9 +201,10 @@
 			clk_disable_unprepare(imx_uart_clocks[i]);
 			clk_put(imx_uart_clocks[i]);
 		}
-		kfree(imx_uart_clocks);
 	}
 
+	kfree(imx_uart_clocks);
+
 	return 0;
 }
 late_initcall_sync(imx_clk_disable_uart);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ingenic/cgu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ingenic/cgu.c
@@ -453,15 +453,15 @@
 	}
 
 	/* Impose hardware constraints */
-	div = min_t(unsigned, div, 1 << clk_info->div.bits);
-	div = max_t(unsigned, div, 1);
+	div = clamp_t(unsigned int, div, clk_info->div.div,
+		      clk_info->div.div << clk_info->div.bits);
 
 	/*
 	 * If the divider value itself must be divided before being written to
 	 * the divider register, we must ensure we don't have any bits set that
 	 * would be lost as a result of doing so.
 	 */
-	div /= clk_info->div.div;
+	div = DIV_ROUND_UP(div, clk_info->div.div);
 	div *= clk_info->div.div;
 
 	return div;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ingenic/jz4725b-cgu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ingenic/jz4725b-cgu.c
@@ -139,11 +139,10 @@
 	},
 
 	[JZ4725B_CLK_I2S] = {
-		"i2s", CGU_CLK_MUX | CGU_CLK_DIV | CGU_CLK_GATE,
+		"i2s", CGU_CLK_MUX | CGU_CLK_DIV,
 		.parents = { JZ4725B_CLK_EXT, JZ4725B_CLK_PLL_HALF, -1, -1 },
 		.mux = { CGU_REG_CPCCR, 31, 1 },
 		.div = { CGU_REG_I2SCDR, 0, 1, 9, -1, -1, -1 },
-		.gate = { CGU_REG_CLKGR, 6 },
 	},
 
 	[JZ4725B_CLK_SPI] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ingenic/jz4760-cgu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ingenic/jz4760-cgu.c
@@ -58,7 +58,7 @@
 		       unsigned long rate, unsigned long parent_rate,
 		       unsigned int *pm, unsigned int *pn, unsigned int *pod)
 {
-	unsigned int m, n, od, m_max = (1 << pll_info->m_bits) - 2;
+	unsigned int m, n, od, m_max = (1 << pll_info->m_bits) - 1;
 
 	/* The frequency after the N divider must be between 1 and 50 MHz. */
 	n = parent_rate / (1 * MHZ);
@@ -66,19 +66,17 @@
 	/* The N divider must be >= 2. */
 	n = clamp_val(n, 2, 1 << pll_info->n_bits);
 
-	for (;; n >>= 1) {
-		od = (unsigned int)-1;
+	rate /= MHZ;
+	parent_rate /= MHZ;
 
-		do {
-			m = (rate / MHZ) * (1 << ++od) * n / (parent_rate / MHZ);
-		} while ((m > m_max || m & 1) && (od < 4));
-
-		if (od < 4 && m >= 4 && m <= m_max)
-			break;
+	for (m = m_max; m >= m_max && n >= 2; n--) {
+		m = rate * n / parent_rate;
+		od = m & 1;
+		m <<= od;
 	}
 
 	*pm = m;
-	*pn = n;
+	*pn = n + 1;
 	*pod = 1 << od;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ingenic/tcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ingenic/tcu.c
@@ -100,15 +100,11 @@
 	bool enabled = false;
 
 	/*
-	 * If the SoC has no global TCU clock, we must ungate the channel's
-	 * clock to be able to access its registers.
-	 * If we have a TCU clock, it will be enabled automatically as it has
-	 * been attached to the regmap.
+	 * According to the programming manual, a timer channel's registers can
+	 * only be accessed when the channel's stop bit is clear.
 	 */
-	if (!tcu->clk) {
-		enabled = !!ingenic_tcu_is_enabled(hw);
-		regmap_write(tcu->map, TCU_REG_TSCR, BIT(info->gate_bit));
-	}
+	enabled = !!ingenic_tcu_is_enabled(hw);
+	regmap_write(tcu->map, TCU_REG_TSCR, BIT(info->gate_bit));
 
 	return enabled;
 }
@@ -119,8 +115,7 @@
 	const struct ingenic_tcu_clk_info *info = tcu_clk->info;
 	struct ingenic_tcu *tcu = tcu_clk->tcu;
 
-	if (!tcu->clk)
-		regmap_write(tcu->map, TCU_REG_TSSR, BIT(info->gate_bit));
+	regmap_write(tcu->map, TCU_REG_TSSR, BIT(info->gate_bit));
 }
 
 static u8 ingenic_tcu_get_parent(struct clk_hw *hw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/keystone/pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/keystone/pll.c
@@ -209,7 +209,7 @@
 	}
 
 	clk = clk_register_pll(NULL, node->name, parent_name, pll_data);
-	if (clk) {
+	if (!IS_ERR_OR_NULL(clk)) {
 		of_clk_add_provider(node, of_clk_src_simple_get, clk);
 		return;
 	}
@@ -281,12 +281,13 @@
 
 	clk = clk_register_divider(NULL, clk_name, parent_name, 0, reg, shift,
 				 mask, 0, NULL);
-	if (clk) {
-		of_clk_add_provider(node, of_clk_src_simple_get, clk);
-	} else {
+	if (IS_ERR(clk)) {
 		pr_err("%s: error registering divider %s\n", __func__, clk_name);
 		iounmap(reg);
+		return;
 	}
+
+	of_clk_add_provider(node, of_clk_src_simple_get, clk);
 }
 CLK_OF_DECLARE(pll_divider_clock, "ti,keystone,pll-divider-clock", of_pll_div_clk_init);
 
@@ -328,10 +329,12 @@
 	clk = clk_register_mux(NULL, clk_name, (const char **)&parents,
 				ARRAY_SIZE(parents) , 0, reg, shift, mask,
 				0, NULL);
-	if (clk)
-		of_clk_add_provider(node, of_clk_src_simple_get, clk);
-	else
+	if (IS_ERR(clk)) {
 		pr_err("%s: error registering mux %s\n", __func__, clk_name);
+		return;
+	}
+
+	of_clk_add_provider(node, of_clk_src_simple_get, clk);
 }
 CLK_OF_DECLARE(pll_mux_clock, "ti,keystone,pll-mux-clock", of_pll_mux_clk_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/keystone/sci-clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/keystone/sci-clk.c
@@ -302,6 +302,8 @@
 
 	name = kasprintf(GFP_KERNEL, "clk:%d:%d", sci_clk->dev_id,
 			 sci_clk->clk_id);
+	if (!name)
+		return -ENOMEM;
 
 	init.name = name;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/loongson1/clk-loongson1c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/loongson1/clk-loongson1c.c
@@ -37,6 +37,7 @@
 	[1] = { .val = 1, .div = 4 },
 	[2] = { .val = 2, .div = 3 },
 	[3] = { .val = 3, .div = 3 },
+	[4] = { /* sentinel */ }
 };
 
 void __init ls1x_clk_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt2701.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt2701.c
@@ -675,6 +675,8 @@
 		return PTR_ERR(base);
 
 	clk_data = mtk_alloc_clk_data(CLK_TOP_NR);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_fixed_clks(top_fixed_clks, ARRAY_SIZE(top_fixed_clks),
 								clk_data);
@@ -742,6 +744,8 @@
 
 	if (!infra_clk_data) {
 		infra_clk_data = mtk_alloc_clk_data(CLK_INFRA_NR);
+		if (!infra_clk_data)
+			return;
 
 		for (i = 0; i < CLK_INFRA_NR; i++)
 			infra_clk_data->clks[i] = ERR_PTR(-EPROBE_DEFER);
@@ -768,6 +772,8 @@
 
 	if (!infra_clk_data) {
 		infra_clk_data = mtk_alloc_clk_data(CLK_INFRA_NR);
+		if (!infra_clk_data)
+			return -ENOMEM;
 	} else {
 		for (i = 0; i < CLK_INFRA_NR; i++) {
 			if (infra_clk_data->clks[i] == ERR_PTR(-EPROBE_DEFER))
@@ -896,6 +902,8 @@
 		return PTR_ERR(base);
 
 	clk_data = mtk_alloc_clk_data(CLK_PERI_NR);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_gates(node, peri_clks, ARRAY_SIZE(peri_clks),
 						clk_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt6765.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt6765.c
@@ -785,6 +785,8 @@
 	}
 
 	clk_data = mtk_alloc_clk_data(CLK_APMIXED_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data);
 
@@ -820,6 +822,8 @@
 	}
 
 	clk_data = mtk_alloc_clk_data(CLK_TOP_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_fixed_clks(fixed_clks, ARRAY_SIZE(fixed_clks),
 				    clk_data);
@@ -860,6 +864,8 @@
 	}
 
 	clk_data = mtk_alloc_clk_data(CLK_IFR_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_gates(node, ifr_clks, ARRAY_SIZE(ifr_clks),
 			       clk_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt6779.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt6779.c
@@ -1216,6 +1216,8 @@
 	struct device_node *node = pdev->dev.of_node;
 
 	clk_data = mtk_alloc_clk_data(CLK_APMIXED_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data);
 
@@ -1236,6 +1238,8 @@
 		return PTR_ERR(base);
 
 	clk_data = mtk_alloc_clk_data(CLK_TOP_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_fixed_clks(top_fixed_clks, ARRAY_SIZE(top_fixed_clks),
 				    clk_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt6797.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt6797.c
@@ -391,6 +391,8 @@
 		return PTR_ERR(base);
 
 	clk_data = mtk_alloc_clk_data(CLK_TOP_NR);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_factors(top_fixed_divs, ARRAY_SIZE(top_fixed_divs),
 				 clk_data);
@@ -563,6 +565,8 @@
 
 	if (!infra_clk_data) {
 		infra_clk_data = mtk_alloc_clk_data(CLK_INFRA_NR);
+		if (!infra_clk_data)
+			return;
 
 		for (i = 0; i < CLK_INFRA_NR; i++)
 			infra_clk_data->clks[i] = ERR_PTR(-EPROBE_DEFER);
@@ -587,6 +591,8 @@
 
 	if (!infra_clk_data) {
 		infra_clk_data = mtk_alloc_clk_data(CLK_INFRA_NR);
+		if (!infra_clk_data)
+			return -ENOMEM;
 	} else {
 		for (i = 0; i < CLK_INFRA_NR; i++) {
 			if (infra_clk_data->clks[i] == ERR_PTR(-EPROBE_DEFER))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt7629-eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt7629-eth.c
@@ -83,6 +83,8 @@
 	int r;
 
 	clk_data = mtk_alloc_clk_data(CLK_ETH_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_gates(node, eth_clks, CLK_ETH_NR_CLK, clk_data);
 
@@ -105,6 +107,8 @@
 	int r;
 
 	clk_data = mtk_alloc_clk_data(CLK_SGMII_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_gates(node, sgmii_clks[id++], CLK_SGMII_NR_CLK,
 			       clk_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt7629.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt7629.c
@@ -580,6 +580,8 @@
 		return PTR_ERR(base);
 
 	clk_data = mtk_alloc_clk_data(CLK_TOP_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_fixed_clks(top_fixed_clks, ARRAY_SIZE(top_fixed_clks),
 				    clk_data);
@@ -603,6 +605,8 @@
 	struct clk_onecell_data *clk_data;
 
 	clk_data = mtk_alloc_clk_data(CLK_INFRA_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_gates(node, infra_clks, ARRAY_SIZE(infra_clks),
 			       clk_data);
@@ -626,6 +630,8 @@
 		return PTR_ERR(base);
 
 	clk_data = mtk_alloc_clk_data(CLK_PERI_NR_CLK);
+	if (!clk_data)
+		return -ENOMEM;
 
 	mtk_clk_register_gates(node, peri_clks, ARRAY_SIZE(peri_clks),
 			       clk_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/clk-mt8183-mfgcfg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/clk-mt8183-mfgcfg.c
@@ -18,9 +18,9 @@
 	.sta_ofs = 0x0,
 };
 
-#define GATE_MFG(_id, _name, _parent, _shift)			\
-	GATE_MTK(_id, _name, _parent, &mfg_cg_regs, _shift,	\
-		&mtk_clk_gate_ops_setclr)
+#define GATE_MFG(_id, _name, _parent, _shift)				\
+	GATE_MTK_FLAGS(_id, _name, _parent, &mfg_cg_regs, _shift,	\
+		       &mtk_clk_gate_ops_setclr, CLK_SET_RATE_PARENT)
 
 static const struct mtk_gate mfg_clks[] = {
 	GATE_MFG(CLK_MFG_BG3D, "mfg_bg3d", "mfg_sel", 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mediatek/reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mediatek/reset.c
@@ -25,7 +25,7 @@
 	struct mtk_reset *data = container_of(rcdev, struct mtk_reset, rcdev);
 	unsigned int reg = data->regofs + ((id / 32) << 4);
 
-	return regmap_write(data->regmap, reg, 1);
+	return regmap_write(data->regmap, reg, BIT(id % 32));
 }
 
 static int mtk_reset_deassert_set_clr(struct reset_controller_dev *rcdev,
@@ -34,7 +34,7 @@
 	struct mtk_reset *data = container_of(rcdev, struct mtk_reset, rcdev);
 	unsigned int reg = data->regofs + ((id / 32) << 4) + 0x4;
 
-	return regmap_write(data->regmap, reg, 1);
+	return regmap_write(data->regmap, reg, BIT(id % 32));
 }
 
 static int mtk_reset_assert(struct reset_controller_dev *rcdev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/meson/axg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/meson/axg.c
@@ -2144,7 +2144,9 @@
 	&axg_vclk_input,
 	&axg_vclk2_input,
 	&axg_vclk_div,
+	&axg_vclk_div1,
 	&axg_vclk2_div,
+	&axg_vclk2_div1,
 	&axg_vclk_div2_en,
 	&axg_vclk_div4_en,
 	&axg_vclk_div6_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/meson/g12a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/meson/g12a.c
@@ -1136,8 +1136,18 @@
 	.hw.init = &(struct clk_init_data) {
 		.name = "cpu_clk_div16_en",
 		.ops = &clk_regmap_gate_ro_ops,
-		.parent_hws = (const struct clk_hw *[]) {
-			&g12a_cpu_clk.hw
+		.parent_data = &(const struct clk_parent_data) {
+			/*
+			 * Note:
+			 * G12A and G12B have different cpu clocks (with
+			 * different struct clk_hw). We fallback to the global
+			 * naming string mechanism so this clock picks
+			 * up the appropriate one. Same goes for the other
+			 * clock using cpu cluster A clock output and present
+			 * on both G12 variant.
+			 */
+			.name = "cpu_clk",
+			.index = -1,
 		},
 		.num_parents = 1,
 		/*
@@ -1202,7 +1212,10 @@
 	.hw.init = &(struct clk_init_data){
 		.name = "cpu_clk_apb_div",
 		.ops = &clk_regmap_divider_ro_ops,
-		.parent_hws = (const struct clk_hw *[]) { &g12a_cpu_clk.hw },
+		.parent_data = &(const struct clk_parent_data) {
+			.name = "cpu_clk",
+			.index = -1,
+		},
 		.num_parents = 1,
 	},
 };
@@ -1236,7 +1249,10 @@
 	.hw.init = &(struct clk_init_data){
 		.name = "cpu_clk_atb_div",
 		.ops = &clk_regmap_divider_ro_ops,
-		.parent_hws = (const struct clk_hw *[]) { &g12a_cpu_clk.hw },
+		.parent_data = &(const struct clk_parent_data) {
+			.name = "cpu_clk",
+			.index = -1,
+		},
 		.num_parents = 1,
 	},
 };
@@ -1270,7 +1286,10 @@
 	.hw.init = &(struct clk_init_data){
 		.name = "cpu_clk_axi_div",
 		.ops = &clk_regmap_divider_ro_ops,
-		.parent_hws = (const struct clk_hw *[]) { &g12a_cpu_clk.hw },
+		.parent_data = &(const struct clk_parent_data) {
+			.name = "cpu_clk",
+			.index = -1,
+		},
 		.num_parents = 1,
 	},
 };
@@ -1305,13 +1324,6 @@
 		.name = "cpu_clk_trace_div",
 		.ops = &clk_regmap_divider_ro_ops,
 		.parent_data = &(const struct clk_parent_data) {
-			/*
-			 * Note:
-			 * G12A and G12B have different cpu_clks (with
-			 * different struct clk_hw). We fallback to the global
-			 * naming string mechanism so cpu_clk_trace_div picks
-			 * up the appropriate one.
-			 */
 			.name = "cpu_clk",
 			.index = -1,
 		},
@@ -4187,7 +4199,7 @@
 static MESON_GATE(g12a_hiu_reg,			HHI_GCLK_MPEG0,	19);
 static MESON_GATE(g12a_mipi_dsi_phy,		HHI_GCLK_MPEG0,	20);
 static MESON_GATE(g12a_assist_misc,		HHI_GCLK_MPEG0,	23);
-static MESON_GATE(g12a_emmc_a,			HHI_GCLK_MPEG0,	4);
+static MESON_GATE(g12a_emmc_a,			HHI_GCLK_MPEG0,	24);
 static MESON_GATE(g12a_emmc_b,			HHI_GCLK_MPEG0,	25);
 static MESON_GATE(g12a_emmc_c,			HHI_GCLK_MPEG0,	26);
 static MESON_GATE(g12a_audio_codec,		HHI_GCLK_MPEG0,	28);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/meson/gxbb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/meson/gxbb.c
@@ -720,6 +720,35 @@
 			.width   = 14,
 		},
 		.sdm_en = {
+			.reg_off = HHI_MPLL_CNTL,
+			.shift   = 25,
+			.width	 = 1,
+		},
+		.n2 = {
+			.reg_off = HHI_MPLL_CNTL7,
+			.shift   = 16,
+			.width   = 9,
+		},
+		.lock = &meson_clk_lock,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "mpll0_div",
+		.ops = &meson_clk_mpll_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&gxbb_mpll_prediv.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap gxl_mpll0_div = {
+	.data = &(struct meson_clk_mpll_data){
+		.sdm = {
+			.reg_off = HHI_MPLL_CNTL7,
+			.shift   = 0,
+			.width   = 14,
+		},
+		.sdm_en = {
 			.reg_off = HHI_MPLL_CNTL7,
 			.shift   = 15,
 			.width	 = 1,
@@ -749,7 +778,16 @@
 	.hw.init = &(struct clk_init_data){
 		.name = "mpll0",
 		.ops = &clk_regmap_gate_ops,
-		.parent_hws = (const struct clk_hw *[]) { &gxbb_mpll0_div.hw },
+		.parent_data = &(const struct clk_parent_data) {
+			/*
+			 * Note:
+			 * GXL and GXBB have different SDM_EN registers. We
+			 * fallback to the global naming string mechanism so
+			 * mpll0_div picks up the appropriate one.
+			 */
+			.name = "mpll0_div",
+			.index = -1,
+		},
 		.num_parents = 1,
 		.flags = CLK_SET_RATE_PARENT,
 	},
@@ -1232,14 +1270,13 @@
 	},
 };
 
+/*
+ * This table skips a clock named 'cts_slow_oscin' in the documentation
+ * This clock does not exist yet in this controller or the AO one
+ */
+static u32 gxbb_32k_clk_parents_val_table[] = { 0, 2, 3 };
 static const struct clk_parent_data gxbb_32k_clk_parent_data[] = {
 	{ .fw_name = "xtal", },
-	/*
-	 * FIXME: This clock is provided by the ao clock controller but the
-	 * clock is not yet part of the binding of this controller, so string
-	 * name must be use to set this parent.
-	 */
-	{ .name = "cts_slow_oscin", .index = -1 },
 	{ .hw = &gxbb_fclk_div3.hw },
 	{ .hw = &gxbb_fclk_div5.hw },
 };
@@ -1249,6 +1286,7 @@
 		.offset = HHI_32K_CLK_CNTL,
 		.mask = 0x3,
 		.shift = 16,
+		.table = gxbb_32k_clk_parents_val_table,
 		},
 	.hw.init = &(struct clk_init_data){
 		.name = "32k_clk_sel",
@@ -1272,7 +1310,7 @@
 			&gxbb_32k_clk_sel.hw
 		},
 		.num_parents = 1,
-		.flags = CLK_SET_RATE_PARENT | CLK_DIVIDER_ROUND_CLOSEST,
+		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -3044,7 +3082,7 @@
 		[CLKID_VAPB_1]		    = &gxbb_vapb_1.hw,
 		[CLKID_VAPB_SEL]	    = &gxbb_vapb_sel.hw,
 		[CLKID_VAPB]		    = &gxbb_vapb.hw,
-		[CLKID_MPLL0_DIV]	    = &gxbb_mpll0_div.hw,
+		[CLKID_MPLL0_DIV]	    = &gxl_mpll0_div.hw,
 		[CLKID_MPLL1_DIV]	    = &gxbb_mpll1_div.hw,
 		[CLKID_MPLL2_DIV]	    = &gxbb_mpll2_div.hw,
 		[CLKID_MPLL_PREDIV]	    = &gxbb_mpll_prediv.hw,
@@ -3439,7 +3477,7 @@
 	&gxbb_mpll0,
 	&gxbb_mpll1,
 	&gxbb_mpll2,
-	&gxbb_mpll0_div,
+	&gxl_mpll0_div,
 	&gxbb_mpll1_div,
 	&gxbb_mpll2_div,
 	&gxbb_cts_amclk_div,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/meson/meson-aoclk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/meson/meson-aoclk.c
@@ -38,6 +38,7 @@
 	struct meson_aoclk_reset_controller *rstc;
 	struct meson_aoclk_data *data;
 	struct device *dev = &pdev->dev;
+	struct device_node *np;
 	struct regmap *regmap;
 	int ret, clkid;
 
@@ -49,7 +50,9 @@
 	if (!rstc)
 		return -ENOMEM;
 
-	regmap = syscon_node_to_regmap(of_get_parent(dev->of_node));
+	np = of_get_parent(dev->of_node);
+	regmap = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (IS_ERR(regmap)) {
 		dev_err(dev, "failed to get regmap\n");
 		return PTR_ERR(regmap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/meson/meson-eeclk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/meson/meson-eeclk.c
@@ -18,6 +18,7 @@
 {
 	const struct meson_eeclkc_data *data;
 	struct device *dev = &pdev->dev;
+	struct device_node *np;
 	struct regmap *map;
 	int ret, i;
 
@@ -26,7 +27,9 @@
 		return -EINVAL;
 
 	/* Get the hhi system controller node */
-	map = syscon_node_to_regmap(of_get_parent(dev->of_node));
+	np = of_get_parent(dev->of_node);
+	map = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (IS_ERR(map)) {
 		dev_err(dev,
 			"failed to get HHI regmap\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/meson/meson8b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/meson/meson8b.c
@@ -3717,12 +3717,15 @@
 			struct clk_hw_onecell_data *clk_hw_onecell_data)
 {
 	struct meson8b_clk_reset *rstc;
+	struct device_node *parent_np;
 	const char *notifier_clk_name;
 	struct clk *notifier_clk;
 	struct regmap *map;
 	int i, ret;
 
-	map = syscon_node_to_regmap(of_get_parent(np));
+	parent_np = of_get_parent(np);
+	map = syscon_node_to_regmap(parent_np);
+	of_node_put(parent_np);
 	if (IS_ERR(map)) {
 		pr_err("failed to get HHI regmap - Trying obsolete regs\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mmp/clk-of-pxa168.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mmp/clk-of-pxa168.c
@@ -258,18 +258,21 @@
 	pxa_unit->mpmu_base = of_iomap(np, 0);
 	if (!pxa_unit->mpmu_base) {
 		pr_err("failed to map mpmu registers\n");
+		kfree(pxa_unit);
 		return;
 	}
 
 	pxa_unit->apmu_base = of_iomap(np, 1);
 	if (!pxa_unit->apmu_base) {
 		pr_err("failed to map apmu registers\n");
+		kfree(pxa_unit);
 		return;
 	}
 
 	pxa_unit->apbc_base = of_iomap(np, 2);
 	if (!pxa_unit->apbc_base) {
 		pr_err("failed to map apbc registers\n");
+		kfree(pxa_unit);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/mvebu/ap-cpu-clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/mvebu/ap-cpu-clk.c
@@ -256,12 +256,15 @@
 		int cpu, err;
 
 		err = of_property_read_u32(dn, "reg", &cpu);
-		if (WARN_ON(err))
+		if (WARN_ON(err)) {
+			of_node_put(dn);
 			return err;
+		}
 
 		/* If cpu2 or cpu3 is enabled */
 		if (cpu & APN806_CLUSTER_NUM_MASK) {
 			nclusters = 2;
+			of_node_put(dn);
 			break;
 		}
 	}
@@ -288,8 +291,10 @@
 		int cpu, err;
 
 		err = of_property_read_u32(dn, "reg", &cpu);
-		if (WARN_ON(err))
+		if (WARN_ON(err)) {
+			of_node_put(dn);
 			return err;
+		}
 
 		cluster_index = cpu & APN806_CLUSTER_NUM_MASK;
 		cluster_index >>= APN806_CLUSTER_NUM_OFFSET;
@@ -301,6 +306,7 @@
 		parent = of_clk_get(np, cluster_index);
 		if (IS_ERR(parent)) {
 			dev_err(dev, "Could not get the clock parent\n");
+			of_node_put(dn);
 			return -EINVAL;
 		}
 		parent_name =  __clk_get_name(parent);
@@ -319,8 +325,10 @@
 		init.parent_names = &parent_name;
 
 		ret = devm_clk_hw_register(dev, &ap_cpu_clk[cluster_index].hw);
-		if (ret)
+		if (ret) {
+			of_node_put(dn);
 			return ret;
+		}
 		ap_cpu_data->hws[cluster_index] = &ap_cpu_clk[cluster_index].hw;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/Kconfig
@@ -127,6 +127,7 @@
 	tristate "IPQ APSS Clock Controller"
 	select IPQ_APSS_PLL
 	depends on QCOM_APCS_IPC || COMPILE_TEST
+	depends on QCOM_SMEM
 	help
 	  Support for APSS clock controller on IPQ platforms. The
 	  APSS clock controller manages the Mux and enable block that feeds the
@@ -550,6 +551,7 @@
 
 config SM_GCC_6115
 	tristate "SM6115 and SM4250 Global Clock Controller"
+	select QCOM_GDSC
 	help
 	  Support for the global clock controller on SM6115 and SM4250 devices.
 	  Say Y if you want to use peripheral devices such as UART, SPI,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/Makefile
@@ -11,6 +11,7 @@
 clk-qcom-y += clk-regmap-divider.o
 clk-qcom-y += clk-regmap-mux.o
 clk-qcom-y += clk-regmap-mux-div.o
+clk-qcom-y += clk-regmap-phy-mux.o
 clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-krait.o
 clk-qcom-y += clk-hfpll.o
 clk-qcom-y += reset.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/apss-ipq6018.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/apss-ipq6018.c
@@ -57,7 +57,7 @@
 			.parent_hws = (const struct clk_hw *[]){
 				&apcs_alias0_clk_src.clkr.hw },
 			.num_parents = 1,
-			.flags = CLK_SET_RATE_PARENT,
+			.flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
 			.ops = &clk_branch2_ops,
 		},
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/camcc-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/camcc-sc7180.c
@@ -1493,12 +1493,21 @@
 	},
 };
 
+static struct gdsc titan_top_gdsc = {
+	.gdscr = 0xb134,
+	.pd = {
+		.name = "titan_top_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
 static struct gdsc bps_gdsc = {
 	.gdscr = 0x6004,
 	.pd = {
 		.name = "bps_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.parent = &titan_top_gdsc.pd,
 	.flags = HW_CTRL,
 };
 
@@ -1508,6 +1517,7 @@
 		.name = "ife_0_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.parent = &titan_top_gdsc.pd,
 };
 
 static struct gdsc ife_1_gdsc = {
@@ -1516,6 +1526,7 @@
 		.name = "ife_1_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.parent = &titan_top_gdsc.pd,
 };
 
 static struct gdsc ipe_0_gdsc = {
@@ -1525,15 +1536,9 @@
 	},
 	.pwrsts = PWRSTS_OFF_ON,
 	.flags = HW_CTRL,
+	.parent = &titan_top_gdsc.pd,
 };
 
-static struct gdsc titan_top_gdsc = {
-	.gdscr = 0xb134,
-	.pd = {
-		.name = "titan_top_gdsc",
-	},
-	.pwrsts = PWRSTS_OFF_ON,
-};
 
 static struct clk_hw *cam_cc_sc7180_hws[] = {
 	[CAM_CC_PLL2_OUT_EARLY] = &cam_cc_pll2_out_early.hw,
@@ -1672,7 +1677,7 @@
 		return ret;
 	}
 
-	ret = pm_runtime_get(&pdev->dev);
+	ret = pm_runtime_resume_and_get(&pdev->dev);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/camcc-sdm845.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/camcc-sdm845.c
@@ -1521,6 +1521,8 @@
 	},
 };
 
+static struct gdsc titan_top_gdsc;
+
 static struct gdsc bps_gdsc = {
 	.gdscr = 0x6004,
 	.pd = {
@@ -1554,6 +1556,7 @@
 		.name = "ife_0_gdsc",
 	},
 	.flags = POLL_CFG_GDSCR,
+	.parent = &titan_top_gdsc.pd,
 	.pwrsts = PWRSTS_OFF_ON,
 };
 
@@ -1563,6 +1566,7 @@
 		.name = "ife_1_gdsc",
 	},
 	.flags = POLL_CFG_GDSCR,
+	.parent = &titan_top_gdsc.pd,
 	.pwrsts = PWRSTS_OFF_ON,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/camcc-sm8250.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/camcc-sm8250.c
@@ -2205,6 +2205,8 @@
 	},
 };
 
+static struct gdsc titan_top_gdsc;
+
 static struct gdsc bps_gdsc = {
 	.gdscr = 0x7004,
 	.pd = {
@@ -2238,6 +2240,7 @@
 		.name = "ife_0_gdsc",
 	},
 	.flags = POLL_CFG_GDSCR,
+	.parent = &titan_top_gdsc.pd,
 	.pwrsts = PWRSTS_OFF_ON,
 };
 
@@ -2247,6 +2250,7 @@
 		.name = "ife_1_gdsc",
 	},
 	.flags = POLL_CFG_GDSCR,
+	.parent = &titan_top_gdsc.pd,
 	.pwrsts = PWRSTS_OFF_ON,
 };
 
@@ -2440,17 +2444,7 @@
 	},
 };
 
-static int __init cam_cc_sm8250_init(void)
-{
-	return platform_driver_register(&cam_cc_sm8250_driver);
-}
-subsys_initcall(cam_cc_sm8250_init);
-
-static void __exit cam_cc_sm8250_exit(void)
-{
-	platform_driver_unregister(&cam_cc_sm8250_driver);
-}
-module_exit(cam_cc_sm8250_exit);
+module_platform_driver(cam_cc_sm8250_driver);
 
 MODULE_DESCRIPTION("QTI CAMCC SM8250 Driver");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-alpha-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-alpha-pll.c
@@ -38,7 +38,7 @@
 
 #define PLL_USER_CTL(p)		((p)->offset + (p)->regs[PLL_OFF_USER_CTL])
 # define PLL_POST_DIV_SHIFT	8
-# define PLL_POST_DIV_MASK(p)	GENMASK((p)->width, 0)
+# define PLL_POST_DIV_MASK(p)	GENMASK((p)->width - 1, 0)
 # define PLL_ALPHA_EN		BIT(24)
 # define PLL_ALPHA_MODE		BIT(25)
 # define PLL_VCO_SHIFT		20
@@ -284,6 +284,8 @@
 	mask |= config->pre_div_mask;
 	mask |= config->post_div_mask;
 	mask |= config->vco_mask;
+	mask |= config->alpha_en_mask;
+	mask |= config->alpha_mode_mask;
 
 	regmap_update_bits(regmap, PLL_USER_CTL(pll), mask, val);
 
@@ -1362,8 +1364,8 @@
 	}
 
 	return regmap_update_bits(regmap, PLL_USER_CTL(pll),
-				  PLL_POST_DIV_MASK(pll) << PLL_POST_DIV_SHIFT,
-				  val << PLL_POST_DIV_SHIFT);
+				  PLL_POST_DIV_MASK(pll) << pll->post_div_shift,
+				  val << pll->post_div_shift);
 }
 
 const struct clk_ops clk_alpha_pll_postdiv_trion_ops = {
@@ -1420,7 +1422,7 @@
 EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_fabia_ops);
 
 /**
- * clk_lucid_pll_configure - configure the lucid pll
+ * clk_trion_pll_configure - configure the trion pll
  *
  * @pll: clk alpha pll
  * @regmap: register map
@@ -1429,6 +1431,15 @@
 void clk_trion_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 			     const struct alpha_pll_config *config)
 {
+	/*
+	 * If the bootloader left the PLL enabled it's likely that there are
+	 * RCGs that will lock up if we disable the PLL below.
+	 */
+	if (trion_pll_is_enabled(pll, regmap)) {
+		pr_debug("Trion PLL is already enabled, skipping configuration\n");
+		return;
+	}
+
 	clk_alpha_pll_write_config(regmap, PLL_L_VAL(pll), config->l);
 	regmap_write(regmap, PLL_CAL_L_VAL(pll), TRION_PLL_CAL_VAL);
 	clk_alpha_pll_write_config(regmap, PLL_ALPHA_VAL(pll), config->alpha);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-branch.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-branch.h
@@ -37,6 +37,32 @@
 	struct clk_regmap clkr;
 };
 
+/* Branch clock common bits for HLOS-owned clocks */
+#define CBCR_FORCE_MEM_CORE_ON		BIT(14)
+#define CBCR_FORCE_MEM_PERIPH_ON	BIT(13)
+#define CBCR_FORCE_MEM_PERIPH_OFF	BIT(12)
+
+static inline void qcom_branch_set_force_mem_core(struct regmap *regmap,
+						  struct clk_branch clk, bool on)
+{
+	regmap_update_bits(regmap, clk.halt_reg, CBCR_FORCE_MEM_CORE_ON,
+			   on ? CBCR_FORCE_MEM_CORE_ON : 0);
+}
+
+static inline void qcom_branch_set_force_periph_on(struct regmap *regmap,
+						   struct clk_branch clk, bool on)
+{
+	regmap_update_bits(regmap, clk.halt_reg, CBCR_FORCE_MEM_PERIPH_ON,
+			   on ? CBCR_FORCE_MEM_PERIPH_ON : 0);
+}
+
+static inline void qcom_branch_set_force_periph_off(struct regmap *regmap,
+						    struct clk_branch clk, bool on)
+{
+	regmap_update_bits(regmap, clk.halt_reg, CBCR_FORCE_MEM_PERIPH_OFF,
+			   on ? CBCR_FORCE_MEM_PERIPH_OFF : 0);
+}
+
 extern const struct clk_ops clk_branch_ops;
 extern const struct clk_ops clk_branch2_ops;
 extern const struct clk_ops clk_branch_simple_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-krait.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-krait.c
@@ -32,11 +32,16 @@
 		regval |= (sel & mux->mask) << (mux->shift + LPL_SHIFT);
 	}
 	krait_set_l2_indirect_reg(mux->offset, regval);
-	spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
 
 	/* Wait for switch to complete. */
 	mb();
 	udelay(1);
+
+	/*
+	 * Unlock now to make sure the mux register is not
+	 * modified while switching to the new parent.
+	 */
+	spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
 }
 
 static int krait_mux_set_parent(struct clk_hw *hw, u8 index)
@@ -93,6 +98,8 @@
 
 	if (d->lpl)
 		mask = mask << (d->shift + LPL_SHIFT) | mask << d->shift;
+	else
+		mask <<= d->shift;
 
 	spin_lock_irqsave(&krait_clock_reg_lock, flags);
 	val = krait_get_l2_indirect_reg(d->offset);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-rcg2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-rcg2.c
@@ -13,6 +13,7 @@
 #include <linux/rational.h>
 #include <linux/regmap.h>
 #include <linux/math64.h>
+#include <linux/minmax.h>
 #include <linux/slab.h>
 
 #include <asm/div64.h>
@@ -147,17 +148,11 @@
 static unsigned long
 calc_rate(unsigned long rate, u32 m, u32 n, u32 mode, u32 hid_div)
 {
-	if (hid_div) {
-		rate *= 2;
-		rate /= hid_div + 1;
-	}
+	if (hid_div)
+		rate = mult_frac(rate, 2, hid_div + 1);
 
-	if (mode) {
-		u64 tmp = rate;
-		tmp *= m;
-		do_div(tmp, n);
-		rate = tmp;
-	}
+	if (mode)
+		rate = mult_frac(rate, m, n);
 
 	return rate;
 }
@@ -264,7 +259,7 @@
 
 static int __clk_rcg2_configure(struct clk_rcg2 *rcg, const struct freq_tbl *f)
 {
-	u32 cfg, mask;
+	u32 cfg, mask, d_val, not2d_val, n_minus_m;
 	struct clk_hw *hw = &rcg->clkr.hw;
 	int ret, index = qcom_find_src_index(hw, rcg->parent_map, f->src);
 
@@ -283,8 +278,17 @@
 		if (ret)
 			return ret;
 
+		/* Calculate 2d value */
+		d_val = f->n;
+
+		n_minus_m = f->n - f->m;
+		n_minus_m *= 2;
+
+		d_val = clamp_t(u32, d_val, f->m, n_minus_m);
+		not2d_val = ~d_val & mask;
+
 		ret = regmap_update_bits(rcg->clkr.regmap,
-				RCG_D_OFFSET(rcg), mask, ~f->n);
+				RCG_D_OFFSET(rcg), mask, not2d_val);
 		if (ret)
 			return ret;
 	}
@@ -396,7 +400,7 @@
 static int clk_rcg2_set_duty_cycle(struct clk_hw *hw, struct clk_duty *duty)
 {
 	struct clk_rcg2 *rcg = to_clk_rcg2(hw);
-	u32 notn_m, n, m, d, not2d, mask, duty_per;
+	u32 notn_m, n, m, d, not2d, mask, duty_per, cfg;
 	int ret;
 
 	/* Duty-cycle cannot be modified for non-MND RCGs */
@@ -407,6 +411,11 @@
 
 	regmap_read(rcg->clkr.regmap, RCG_N_OFFSET(rcg), &notn_m);
 	regmap_read(rcg->clkr.regmap, RCG_M_OFFSET(rcg), &m);
+	regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg);
+
+	/* Duty-cycle cannot be modified if MND divider is in bypass mode. */
+	if (!(cfg & CFG_MODE_MASK))
+		return -EINVAL;
 
 	n = (~(notn_m) + m) & mask;
 
@@ -415,9 +424,11 @@
 	/* Calculate 2d value */
 	d = DIV_ROUND_CLOSEST(n * duty_per * 2, 100);
 
-	 /* Check bit widths of 2d. If D is too big reduce duty cycle. */
-	if (d > mask)
-		d = mask;
+	/*
+	 * Check bit widths of 2d. If D is too big reduce duty cycle.
+	 * Also make sure it is never zero.
+	 */
+	d = clamp_val(d, 1, mask);
 
 	if ((d / 2) > (n - m))
 		d = (n - m) * 2;
@@ -720,6 +731,7 @@
 	{ 2, 9 },
 	{ 4, 9 },
 	{ 1, 1 },
+	{ 2, 3 },
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-regmap-mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-regmap-mux.c
@@ -28,7 +28,7 @@
 	val &= mask;
 
 	if (mux->parent_map)
-		return qcom_find_src_index(hw, mux->parent_map, val);
+		return qcom_find_cfg_index(hw, mux->parent_map, val);
 
 	return val;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-regmap-phy-mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-regmap-phy-mux.c
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Linaro Ltd.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/bitfield.h>
+#include <linux/regmap.h>
+#include <linux/export.h>
+
+#include "clk-regmap.h"
+#include "clk-regmap-phy-mux.h"
+
+#define PHY_MUX_MASK		GENMASK(1, 0)
+#define PHY_MUX_PHY_SRC		0
+#define PHY_MUX_REF_SRC		2
+
+static inline struct clk_regmap_phy_mux *to_clk_regmap_phy_mux(struct clk_regmap *clkr)
+{
+	return container_of(clkr, struct clk_regmap_phy_mux, clkr);
+}
+
+static int phy_mux_is_enabled(struct clk_hw *hw)
+{
+	struct clk_regmap *clkr = to_clk_regmap(hw);
+	struct clk_regmap_phy_mux *phy_mux = to_clk_regmap_phy_mux(clkr);
+	unsigned int val;
+
+	regmap_read(clkr->regmap, phy_mux->reg, &val);
+	val = FIELD_GET(PHY_MUX_MASK, val);
+
+	WARN_ON(val != PHY_MUX_PHY_SRC && val != PHY_MUX_REF_SRC);
+
+	return val == PHY_MUX_PHY_SRC;
+}
+
+static int phy_mux_enable(struct clk_hw *hw)
+{
+	struct clk_regmap *clkr = to_clk_regmap(hw);
+	struct clk_regmap_phy_mux *phy_mux = to_clk_regmap_phy_mux(clkr);
+
+	return regmap_update_bits(clkr->regmap, phy_mux->reg,
+				  PHY_MUX_MASK,
+				  FIELD_PREP(PHY_MUX_MASK, PHY_MUX_PHY_SRC));
+}
+
+static void phy_mux_disable(struct clk_hw *hw)
+{
+	struct clk_regmap *clkr = to_clk_regmap(hw);
+	struct clk_regmap_phy_mux *phy_mux = to_clk_regmap_phy_mux(clkr);
+
+	regmap_update_bits(clkr->regmap, phy_mux->reg,
+			   PHY_MUX_MASK,
+			   FIELD_PREP(PHY_MUX_MASK, PHY_MUX_REF_SRC));
+}
+
+const struct clk_ops clk_regmap_phy_mux_ops = {
+	.enable = phy_mux_enable,
+	.disable = phy_mux_disable,
+	.is_enabled = phy_mux_is_enabled,
+};
+EXPORT_SYMBOL_GPL(clk_regmap_phy_mux_ops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-regmap-phy-mux.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-regmap-phy-mux.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2022, Linaro Ltd.
+ */
+
+#ifndef __QCOM_CLK_REGMAP_PHY_MUX_H__
+#define __QCOM_CLK_REGMAP_PHY_MUX_H__
+
+#include "clk-regmap.h"
+
+/*
+ * A clock implementation for PHY pipe and symbols clock muxes.
+ *
+ * If the clock is running off the from-PHY source, report it as enabled.
+ * Report it as disabled otherwise (if it uses reference source).
+ *
+ * This way the PHY will disable the pipe clock before turning off the GDSC,
+ * which in turn would lead to disabling corresponding pipe_clk_src (and thus
+ * it being parked to a safe, reference clock source). And vice versa, after
+ * enabling the GDSC the PHY will enable the pipe clock, which would cause
+ * pipe_clk_src to be switched from a safe source to the working one.
+ *
+ * For some platforms this should be used for the UFS symbol_clk_src clocks
+ * too.
+ */
+struct clk_regmap_phy_mux {
+	u32			reg;
+	struct clk_regmap	clkr;
+};
+
+extern const struct clk_ops clk_regmap_phy_mux_ops;
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/clk-rpmh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/clk-rpmh.c
@@ -270,6 +270,8 @@
 		cmd_state = 0;
 	}
 
+	cmd_state = min(cmd_state, BCM_TCS_CMD_VOTE_MASK);
+
 	if (c->last_sent_aggr_state != cmd_state) {
 		cmd.addr = c->res_addr;
 		cmd.data = BCM_TCS_CMD(1, enable, 0, cmd_state);
@@ -329,7 +331,7 @@
 {
 	struct clk_rpmh *c = to_clk_rpmh(hw);
 
-	return c->aggr_state * c->unit;
+	return (unsigned long)c->aggr_state * c->unit;
 }
 
 static const struct clk_ops clk_rpmh_bcm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/common.c
@@ -69,6 +69,18 @@
 }
 EXPORT_SYMBOL_GPL(qcom_find_src_index);
 
+int qcom_find_cfg_index(struct clk_hw *hw, const struct parent_map *map, u8 cfg)
+{
+	int i, num_parents = clk_hw_get_num_parents(hw);
+
+	for (i = 0; i < num_parents; i++)
+		if (cfg == map[i].cfg)
+			return i;
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL_GPL(qcom_find_cfg_index);
+
 struct regmap *
 qcom_cc_map(struct platform_device *pdev, const struct qcom_cc_desc *desc)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/common.h
@@ -49,6 +49,8 @@
 qcom_pll_set_fsm_mode(struct regmap *m, u32 reg, u8 bias_count, u8 lock_count);
 extern int qcom_find_src_index(struct clk_hw *hw, const struct parent_map *map,
 			       u8 src);
+extern int qcom_find_cfg_index(struct clk_hw *hw, const struct parent_map *map,
+			       u8 cfg);
 
 extern int qcom_cc_register_board_clk(struct device *dev, const char *path,
 				      const char *name, unsigned long rate);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/dispcc-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/dispcc-sc7180.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, 2022, The Linux Foundation. All rights reserved.
  */
 
 #include <linux/clk-provider.h>
@@ -625,6 +625,9 @@
 
 static struct gdsc mdss_gdsc = {
 	.gdscr = 0x3000,
+	.en_rest_wait_val = 0x2,
+	.en_few_wait_val = 0x2,
+	.clk_dis_wait_val = 0xf,
 	.pd = {
 		.name = "mdss_gdsc",
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/dispcc-sc7280.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/dispcc-sc7280.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2022, The Linux Foundation. All rights reserved.
  */
 
 #include <linux/clk-provider.h>
@@ -787,6 +787,9 @@
 
 static struct gdsc disp_cc_mdss_core_gdsc = {
 	.gdscr = 0x1004,
+	.en_rest_wait_val = 0x2,
+	.en_few_wait_val = 0x2,
+	.clk_dis_wait_val = 0xf,
 	.pd = {
 		.name = "disp_cc_mdss_core_gdsc",
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/dispcc-sdm845.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/dispcc-sdm845.c
@@ -759,6 +759,8 @@
 
 static struct gdsc mdss_gdsc = {
 	.gdscr = 0x3000,
+	.en_few_wait_val = 0x6,
+	.en_rest_wait_val = 0x5,
 	.pd = {
 		.name = "mdss_gdsc",
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/dispcc-sm8250.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/dispcc-sm8250.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, 2022, The Linux Foundation. All rights reserved.
  */
 
 #include <linux/clk-provider.h>
@@ -832,6 +832,7 @@
 				&disp_cc_mdss_dp_link1_div_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
 			.ops = &clk_branch2_ops,
 		},
 	},
@@ -867,6 +868,7 @@
 				&disp_cc_mdss_dp_link_div_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
 			.ops = &clk_branch2_ops,
 		},
 	},
@@ -992,6 +994,7 @@
 				&disp_cc_mdss_mdp_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
 			.ops = &clk_branch2_ops,
 		},
 	},
@@ -1125,6 +1128,9 @@
 
 static struct gdsc mdss_gdsc = {
 	.gdscr = 0x3000,
+	.en_rest_wait_val = 0x2,
+	.en_few_wait_val = 0x2,
+	.clk_dis_wait_val = 0xf,
 	.pd = {
 		.name = "mdss_gdsc",
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-ipq6018.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-ipq6018.c
@@ -75,7 +75,6 @@
 				&gpll0_main.clkr.hw },
 		.num_parents = 1,
 		.ops = &clk_fixed_factor_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -89,7 +88,6 @@
 				&gpll0_main.clkr.hw },
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -164,7 +162,6 @@
 				&gpll6_main.clkr.hw },
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -195,7 +192,6 @@
 				&gpll4_main.clkr.hw },
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -246,7 +242,6 @@
 				&gpll2_main.clkr.hw },
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -277,7 +272,6 @@
 				&nss_crypto_pll_main.clkr.hw },
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -1563,6 +1557,7 @@
 
 static const struct freq_tbl ftbl_pcie_aux_clk_src[] = {
 	F(24000000, P_XO, 1, 0, 0),
+	{ }
 };
 
 static const struct clk_parent_data gcc_xo_gpll0_core_pi_sleep_clk[] = {
@@ -1654,7 +1649,7 @@
 		.name = "sdcc1_apps_clk_src",
 		.parent_data = gcc_xo_gpll0_gpll2_gpll0_out_main_div2,
 		.num_parents = 4,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_floor_ops,
 	},
 };
 
@@ -1743,6 +1738,7 @@
 	F(160000000, P_GPLL0, 5, 0, 0),
 	F(216000000, P_GPLL6, 5, 0, 0),
 	F(308570000, P_GPLL6, 3.5, 0, 0),
+	{ }
 };
 
 static const struct clk_parent_data gcc_xo_gpll0_gpll6_gpll0_div2[] = {
@@ -4517,24 +4513,24 @@
 	[GCC_PCIE0_AHB_ARES] = { 0x75040, 5 },
 	[GCC_PCIE0_AXI_MASTER_STICKY_ARES] = { 0x75040, 6 },
 	[GCC_PCIE0_AXI_SLAVE_STICKY_ARES] = { 0x75040, 7 },
-	[GCC_PPE_FULL_RESET] = { 0x68014, 0 },
-	[GCC_UNIPHY0_SOFT_RESET] = { 0x56004, 0 },
+	[GCC_PPE_FULL_RESET] = { .reg = 0x68014, .bitmask = 0xf0000 },
+	[GCC_UNIPHY0_SOFT_RESET] = { .reg = 0x56004, .bitmask = 0x3ff2 },
 	[GCC_UNIPHY0_XPCS_RESET] = { 0x56004, 2 },
-	[GCC_UNIPHY1_SOFT_RESET] = { 0x56104, 0 },
+	[GCC_UNIPHY1_SOFT_RESET] = { .reg = 0x56104, .bitmask = 0x32 },
 	[GCC_UNIPHY1_XPCS_RESET] = { 0x56104, 2 },
-	[GCC_EDMA_HW_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT1_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT2_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT3_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT4_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT5_RESET] = { 0x68014, 0 },
-	[GCC_UNIPHY0_PORT1_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT2_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT3_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT4_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT5_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT_4_5_RESET] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT_4_RESET] = { 0x56004, 0 },
+	[GCC_EDMA_HW_RESET] = { .reg = 0x68014, .bitmask = 0x300000 },
+	[GCC_NSSPORT1_RESET] = { .reg = 0x68014, .bitmask = 0x1000003 },
+	[GCC_NSSPORT2_RESET] = { .reg = 0x68014, .bitmask = 0x200000c },
+	[GCC_NSSPORT3_RESET] = { .reg = 0x68014, .bitmask = 0x4000030 },
+	[GCC_NSSPORT4_RESET] = { .reg = 0x68014, .bitmask = 0x8000300 },
+	[GCC_NSSPORT5_RESET] = { .reg = 0x68014, .bitmask = 0x10000c00 },
+	[GCC_UNIPHY0_PORT1_ARES] = { .reg = 0x56004, .bitmask = 0x30 },
+	[GCC_UNIPHY0_PORT2_ARES] = { .reg = 0x56004, .bitmask = 0xc0 },
+	[GCC_UNIPHY0_PORT3_ARES] = { .reg = 0x56004, .bitmask = 0x300 },
+	[GCC_UNIPHY0_PORT4_ARES] = { .reg = 0x56004, .bitmask = 0xc00 },
+	[GCC_UNIPHY0_PORT5_ARES] = { .reg = 0x56004, .bitmask = 0x3000 },
+	[GCC_UNIPHY0_PORT_4_5_RESET] = { .reg = 0x56004, .bitmask = 0x3c02 },
+	[GCC_UNIPHY0_PORT_4_RESET] = { .reg = 0x56004, .bitmask = 0xc02 },
 	[GCC_LPASS_BCR] = {0x1F000, 0},
 	[GCC_UBI32_TBU_BCR] = {0x65000, 0},
 	[GCC_LPASS_TBU_BCR] = {0x6C000, 0},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-ipq8074.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-ipq8074.c
@@ -60,11 +60,6 @@
 	{ P_GPLL0_DIV2, 4 },
 };
 
-static const char * const gcc_xo_gpll0[] = {
-	"xo",
-	"gpll0",
-};
-
 static const struct parent_map gcc_xo_gpll0_map[] = {
 	{ P_XO, 0 },
 	{ P_GPLL0, 1 },
@@ -423,7 +418,6 @@
 		},
 		.num_parents = 1,
 		.ops = &clk_fixed_factor_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -470,7 +464,6 @@
 		},
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -503,7 +496,6 @@
 		},
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -537,7 +529,6 @@
 		},
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -551,7 +542,6 @@
 		},
 		.num_parents = 1,
 		.ops = &clk_fixed_factor_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -616,7 +606,6 @@
 		},
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_ro_ops,
-		.flags = CLK_SET_RATE_PARENT,
 	},
 };
 
@@ -667,6 +656,7 @@
 			},
 			.num_parents = 1,
 			.ops = &clk_branch2_ops,
+			.flags = CLK_IS_CRITICAL,
 		},
 	},
 };
@@ -956,6 +946,11 @@
 	},
 };
 
+static const struct clk_parent_data gcc_xo_gpll0[] = {
+	{ .fw_name = "xo" },
+	{ .hw = &gpll0.clkr.hw },
+};
+
 static const struct freq_tbl ftbl_pcie_axi_clk_src[] = {
 	F(19200000, P_XO, 1, 0, 0),
 	F(200000000, P_GPLL0, 4, 0, 0),
@@ -969,7 +964,7 @@
 	.parent_map = gcc_xo_gpll0_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "pcie0_axi_clk_src",
-		.parent_names = gcc_xo_gpll0,
+		.parent_data = gcc_xo_gpll0,
 		.num_parents = 2,
 		.ops = &clk_rcg2_ops,
 	},
@@ -977,6 +972,7 @@
 
 static const struct freq_tbl ftbl_pcie_aux_clk_src[] = {
 	F(19200000, P_XO, 1, 0, 0),
+	{ }
 };
 
 static struct clk_rcg2 pcie0_aux_clk_src = {
@@ -1016,7 +1012,7 @@
 	.parent_map = gcc_xo_gpll0_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "pcie1_axi_clk_src",
-		.parent_names = gcc_xo_gpll0,
+		.parent_data = gcc_xo_gpll0,
 		.num_parents = 2,
 		.ops = &clk_rcg2_ops,
 	},
@@ -1074,7 +1070,7 @@
 		.name = "sdcc1_apps_clk_src",
 		.parent_names = gcc_xo_gpll0_gpll2_gpll0_out_main_div2,
 		.num_parents = 4,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_floor_ops,
 	},
 };
 
@@ -1082,6 +1078,7 @@
 	F(19200000, P_XO, 1, 0, 0),
 	F(160000000, P_GPLL0, 5, 0, 0),
 	F(308570000, P_GPLL6, 3.5, 0, 0),
+	{ }
 };
 
 static struct clk_rcg2 sdcc1_ice_core_clk_src = {
@@ -1330,7 +1327,7 @@
 	.parent_map = gcc_xo_gpll0_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "nss_ce_clk_src",
-		.parent_names = gcc_xo_gpll0,
+		.parent_data = gcc_xo_gpll0,
 		.num_parents = 2,
 		.ops = &clk_rcg2_ops,
 	},
@@ -1788,8 +1785,10 @@
 static const struct freq_tbl ftbl_nss_port5_rx_clk_src[] = {
 	F(19200000, P_XO, 1, 0, 0),
 	F(25000000, P_UNIPHY1_RX, 12.5, 0, 0),
+	F(25000000, P_UNIPHY0_RX, 5, 0, 0),
 	F(78125000, P_UNIPHY1_RX, 4, 0, 0),
 	F(125000000, P_UNIPHY1_RX, 2.5, 0, 0),
+	F(125000000, P_UNIPHY0_RX, 1, 0, 0),
 	F(156250000, P_UNIPHY1_RX, 2, 0, 0),
 	F(312500000, P_UNIPHY1_RX, 1, 0, 0),
 	{ }
@@ -1828,8 +1827,10 @@
 static const struct freq_tbl ftbl_nss_port5_tx_clk_src[] = {
 	F(19200000, P_XO, 1, 0, 0),
 	F(25000000, P_UNIPHY1_TX, 12.5, 0, 0),
+	F(25000000, P_UNIPHY0_TX, 5, 0, 0),
 	F(78125000, P_UNIPHY1_TX, 4, 0, 0),
 	F(125000000, P_UNIPHY1_TX, 2.5, 0, 0),
+	F(125000000, P_UNIPHY0_TX, 1, 0, 0),
 	F(156250000, P_UNIPHY1_TX, 2, 0, 0),
 	F(312500000, P_UNIPHY1_TX, 1, 0, 0),
 	{ }
@@ -1867,8 +1868,10 @@
 
 static const struct freq_tbl ftbl_nss_port6_rx_clk_src[] = {
 	F(19200000, P_XO, 1, 0, 0),
+	F(25000000, P_UNIPHY2_RX, 5, 0, 0),
 	F(25000000, P_UNIPHY2_RX, 12.5, 0, 0),
 	F(78125000, P_UNIPHY2_RX, 4, 0, 0),
+	F(125000000, P_UNIPHY2_RX, 1, 0, 0),
 	F(125000000, P_UNIPHY2_RX, 2.5, 0, 0),
 	F(156250000, P_UNIPHY2_RX, 2, 0, 0),
 	F(312500000, P_UNIPHY2_RX, 1, 0, 0),
@@ -1907,8 +1910,10 @@
 
 static const struct freq_tbl ftbl_nss_port6_tx_clk_src[] = {
 	F(19200000, P_XO, 1, 0, 0),
+	F(25000000, P_UNIPHY2_TX, 5, 0, 0),
 	F(25000000, P_UNIPHY2_TX, 12.5, 0, 0),
 	F(78125000, P_UNIPHY2_TX, 4, 0, 0),
+	F(125000000, P_UNIPHY2_TX, 1, 0, 0),
 	F(125000000, P_UNIPHY2_TX, 2.5, 0, 0),
 	F(156250000, P_UNIPHY2_TX, 2, 0, 0),
 	F(312500000, P_UNIPHY2_TX, 1, 0, 0),
@@ -3346,6 +3351,7 @@
 
 static struct clk_branch gcc_ubi0_ahb_clk = {
 	.halt_reg = 0x6820c,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x6820c,
 		.enable_mask = BIT(0),
@@ -3363,6 +3369,7 @@
 
 static struct clk_branch gcc_ubi0_axi_clk = {
 	.halt_reg = 0x68200,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68200,
 		.enable_mask = BIT(0),
@@ -3380,6 +3387,7 @@
 
 static struct clk_branch gcc_ubi0_nc_axi_clk = {
 	.halt_reg = 0x68204,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68204,
 		.enable_mask = BIT(0),
@@ -3397,6 +3405,7 @@
 
 static struct clk_branch gcc_ubi0_core_clk = {
 	.halt_reg = 0x68210,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68210,
 		.enable_mask = BIT(0),
@@ -3414,6 +3423,7 @@
 
 static struct clk_branch gcc_ubi0_mpt_clk = {
 	.halt_reg = 0x68208,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68208,
 		.enable_mask = BIT(0),
@@ -3431,6 +3441,7 @@
 
 static struct clk_branch gcc_ubi1_ahb_clk = {
 	.halt_reg = 0x6822c,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x6822c,
 		.enable_mask = BIT(0),
@@ -3448,6 +3459,7 @@
 
 static struct clk_branch gcc_ubi1_axi_clk = {
 	.halt_reg = 0x68220,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68220,
 		.enable_mask = BIT(0),
@@ -3465,6 +3477,7 @@
 
 static struct clk_branch gcc_ubi1_nc_axi_clk = {
 	.halt_reg = 0x68224,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68224,
 		.enable_mask = BIT(0),
@@ -3482,6 +3495,7 @@
 
 static struct clk_branch gcc_ubi1_core_clk = {
 	.halt_reg = 0x68230,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68230,
 		.enable_mask = BIT(0),
@@ -3499,6 +3513,7 @@
 
 static struct clk_branch gcc_ubi1_mpt_clk = {
 	.halt_reg = 0x68228,
+	.halt_check = BRANCH_HALT_DELAY,
 	.clkr = {
 		.enable_reg = 0x68228,
 		.enable_mask = BIT(0),
@@ -4329,8 +4344,7 @@
 	.parent_map = gcc_xo_gpll0_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "pcie0_rchng_clk_src",
-		.parent_hws = (const struct clk_hw *[]) {
-				&gpll0.clkr.hw },
+		.parent_data = gcc_xo_gpll0,
 		.num_parents = 2,
 		.ops = &clk_rcg2_ops,
 	},
@@ -4372,6 +4386,33 @@
 	},
 };
 
+static const struct alpha_pll_config ubi32_pll_config = {
+	.l = 0x4e,
+	.config_ctl_val = 0x200d4aa8,
+	.config_ctl_hi_val = 0x3c2,
+	.main_output_mask = BIT(0),
+	.aux_output_mask = BIT(1),
+	.pre_div_val = 0x0,
+	.pre_div_mask = BIT(12),
+	.post_div_val = 0x0,
+	.post_div_mask = GENMASK(9, 8),
+};
+
+static const struct alpha_pll_config nss_crypto_pll_config = {
+	.l = 0x3e,
+	.alpha = 0x0,
+	.alpha_hi = 0x80,
+	.config_ctl_val = 0x4001055b,
+	.main_output_mask = BIT(0),
+	.pre_div_val = 0x0,
+	.pre_div_mask = GENMASK(14, 12),
+	.post_div_val = 0x1 << 8,
+	.post_div_mask = GENMASK(11, 8),
+	.vco_mask = GENMASK(21, 20),
+	.vco_val = 0x0,
+	.alpha_en_mask = BIT(24),
+};
+
 static struct clk_hw *gcc_ipq8074_hws[] = {
 	&gpll0_out_main_div2.hw,
 	&gpll6_out_main_div2.hw,
@@ -4773,7 +4814,20 @@
 
 static int gcc_ipq8074_probe(struct platform_device *pdev)
 {
-	return qcom_cc_probe(pdev, &gcc_ipq8074_desc);
+	struct regmap *regmap;
+
+	regmap = qcom_cc_map(pdev, &gcc_ipq8074_desc);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	/* SW Workaround for UBI32 Huayra PLL */
+	regmap_update_bits(regmap, 0x2501c, BIT(26), BIT(26));
+
+	clk_alpha_pll_configure(&ubi32_pll_main, regmap, &ubi32_pll_config);
+	clk_alpha_pll_configure(&nss_crypto_pll_main, regmap,
+				&nss_crypto_pll_config);
+
+	return qcom_cc_really_probe(pdev, &gcc_ipq8074_desc, regmap);
 }
 
 static struct platform_driver gcc_ipq8074_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-mdm9607.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-mdm9607.c
@@ -536,7 +536,7 @@
 };
 
 static struct clk_rcg2 blsp1_uart6_apps_clk_src = {
-	.cmd_rcgr = 0x6044,
+	.cmd_rcgr = 0x7044,
 	.mnd_width = 16,
 	.hid_width = 5,
 	.parent_map = gcc_xo_gpll0_map,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-mdm9615.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-mdm9615.c
@@ -58,7 +58,7 @@
 	.enable_mask = BIT(0),
 	.hw.init = &(struct clk_init_data){
 		.name = "pll0_vote",
-		.parent_names = (const char *[]){ "pll8" },
+		.parent_names = (const char *[]){ "pll0" },
 		.num_parents = 1,
 		.ops = &clk_pll_vote_ops,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-msm8939.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-msm8939.c
@@ -632,7 +632,7 @@
 };
 
 static struct clk_rcg2 bimc_ddr_clk_src = {
-	.cmd_rcgr = 0x32004,
+	.cmd_rcgr = 0x32024,
 	.hid_width = 5,
 	.parent_map = gcc_xo_gpll0_bimc_map,
 	.clkr.hw.init = &(struct clk_init_data){
@@ -644,6 +644,18 @@
 	},
 };
 
+static struct clk_rcg2 system_mm_noc_bfdcd_clk_src = {
+	.cmd_rcgr = 0x2600c,
+	.hid_width = 5,
+	.parent_map = gcc_xo_gpll0_gpll6a_map,
+	.clkr.hw.init = &(struct clk_init_data){
+		.name = "system_mm_noc_bfdcd_clk_src",
+		.parent_data = gcc_xo_gpll0_gpll6a_parent_data,
+		.num_parents = 3,
+		.ops = &clk_rcg2_ops,
+	},
+};
+
 static const struct freq_tbl ftbl_gcc_camss_ahb_clk[] = {
 	F(40000000, P_GPLL0, 10, 1, 2),
 	F(80000000, P_GPLL0, 10, 0, 0),
@@ -1002,7 +1014,7 @@
 };
 
 static const struct freq_tbl ftbl_gcc_camss_cci_clk[] = {
-	F(19200000,	P_XO, 1, 0,	0),
+	F(19200000, P_XO, 1, 0, 0),
 	{ }
 };
 
@@ -2441,7 +2453,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_camss_jpeg_axi_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -2645,7 +2657,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_camss_vfe_axi_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -2801,7 +2813,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_mdss_axi_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -3193,7 +3205,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_mdp_tbu_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -3211,7 +3223,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_venus_tbu_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -3229,7 +3241,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_vfe_tbu_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -3247,7 +3259,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_jpeg_tbu_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -3484,7 +3496,7 @@
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_venus0_axi_clk",
 			.parent_data = &(const struct clk_parent_data){
-				.hw = &system_noc_bfdcd_clk_src.clkr.hw,
+				.hw = &system_mm_noc_bfdcd_clk_src.clkr.hw,
 			},
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
@@ -3623,6 +3635,7 @@
 	[GPLL2_VOTE] = &gpll2_vote,
 	[PCNOC_BFDCD_CLK_SRC] = &pcnoc_bfdcd_clk_src.clkr,
 	[SYSTEM_NOC_BFDCD_CLK_SRC] = &system_noc_bfdcd_clk_src.clkr,
+	[SYSTEM_MM_NOC_BFDCD_CLK_SRC] = &system_mm_noc_bfdcd_clk_src.clkr,
 	[CAMSS_AHB_CLK_SRC] = &camss_ahb_clk_src.clkr,
 	[APSS_AHB_CLK_SRC] = &apss_ahb_clk_src.clkr,
 	[CSI0_CLK_SRC] = &csi0_clk_src.clkr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-msm8953.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-msm8953.c
@@ -3771,7 +3771,7 @@
 
 static struct clk_branch gcc_venus0_core0_vcodec0_clk = {
 	.halt_reg = 0x4c02c,
-	.halt_check = BRANCH_HALT,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x4c02c,
 		.enable_mask = BIT(0),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-msm8994.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-msm8994.c
@@ -108,6 +108,7 @@
 
 static struct clk_alpha_pll_postdiv gpll4 = {
 	.offset = 0x1dc0,
+	.width = 4,
 	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data)
 	{
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-msm8996.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-msm8996.c
@@ -2937,20 +2937,6 @@
 	},
 };
 
-static struct clk_branch gcc_aggre1_pnoc_ahb_clk = {
-	.halt_reg = 0x82014,
-	.clkr = {
-		.enable_reg = 0x82014,
-		.enable_mask = BIT(0),
-		.hw.init = &(struct clk_init_data){
-			.name = "gcc_aggre1_pnoc_ahb_clk",
-			.parent_names = (const char *[]){ "periph_noc_clk_src" },
-			.num_parents = 1,
-			.ops = &clk_branch2_ops,
-		},
-	},
-};
-
 static struct clk_branch gcc_aggre2_ufs_axi_clk = {
 	.halt_reg = 0x83014,
 	.clkr = {
@@ -3474,7 +3460,6 @@
 	[GCC_AGGRE0_CNOC_AHB_CLK] = &gcc_aggre0_cnoc_ahb_clk.clkr,
 	[GCC_SMMU_AGGRE0_AXI_CLK] = &gcc_smmu_aggre0_axi_clk.clkr,
 	[GCC_SMMU_AGGRE0_AHB_CLK] = &gcc_smmu_aggre0_ahb_clk.clkr,
-	[GCC_AGGRE1_PNOC_AHB_CLK] = &gcc_aggre1_pnoc_ahb_clk.clkr,
 	[GCC_AGGRE2_UFS_AXI_CLK] = &gcc_aggre2_ufs_axi_clk.clkr,
 	[GCC_AGGRE2_USB3_AXI_CLK] = &gcc_aggre2_usb3_axi_clk.clkr,
 	[GCC_QSPI_AHB_CLK] = &gcc_qspi_ahb_clk.clkr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-qcs404.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-qcs404.c
@@ -25,11 +25,9 @@
 	P_CORE_BI_PLL_TEST_SE,
 	P_DSI0_PHY_PLL_OUT_BYTECLK,
 	P_DSI0_PHY_PLL_OUT_DSICLK,
-	P_GPLL0_OUT_AUX,
 	P_GPLL0_OUT_MAIN,
 	P_GPLL1_OUT_MAIN,
 	P_GPLL3_OUT_MAIN,
-	P_GPLL4_OUT_AUX,
 	P_GPLL4_OUT_MAIN,
 	P_GPLL6_OUT_AUX,
 	P_HDMI_PHY_PLL_CLK,
@@ -109,28 +107,24 @@
 static const struct parent_map gcc_parent_map_5[] = {
 	{ P_XO, 0 },
 	{ P_DSI0_PHY_PLL_OUT_BYTECLK, 1 },
-	{ P_GPLL0_OUT_AUX, 2 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
 static const char * const gcc_parent_names_5[] = {
 	"cxo",
-	"dsi0pll_byteclk_src",
-	"gpll0_out_aux",
+	"dsi0pllbyte",
 	"core_bi_pll_test_se",
 };
 
 static const struct parent_map gcc_parent_map_6[] = {
 	{ P_XO, 0 },
 	{ P_DSI0_PHY_PLL_OUT_BYTECLK, 2 },
-	{ P_GPLL0_OUT_AUX, 3 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
 static const char * const gcc_parent_names_6[] = {
 	"cxo",
-	"dsi0_phy_pll_out_byteclk",
-	"gpll0_out_aux",
+	"dsi0pllbyte",
 	"core_bi_pll_test_se",
 };
 
@@ -139,7 +133,6 @@
 	{ P_GPLL0_OUT_MAIN, 1 },
 	{ P_GPLL3_OUT_MAIN, 2 },
 	{ P_GPLL6_OUT_AUX, 3 },
-	{ P_GPLL4_OUT_AUX, 4 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
@@ -148,7 +141,6 @@
 	"gpll0_out_main",
 	"gpll3_out_main",
 	"gpll6_out_aux",
-	"gpll4_out_aux",
 	"core_bi_pll_test_se",
 };
 
@@ -175,7 +167,7 @@
 static const char * const gcc_parent_names_9[] = {
 	"cxo",
 	"gpll0_out_main",
-	"dsi0_phy_pll_out_dsiclk",
+	"dsi0pll",
 	"gpll6_out_aux",
 	"core_bi_pll_test_se",
 };
@@ -207,14 +199,12 @@
 static const struct parent_map gcc_parent_map_12[] = {
 	{ P_XO, 0 },
 	{ P_DSI0_PHY_PLL_OUT_DSICLK, 1 },
-	{ P_GPLL0_OUT_AUX, 2 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
 static const char * const gcc_parent_names_12[] = {
 	"cxo",
-	"dsi0pll_pclk_src",
-	"gpll0_out_aux",
+	"dsi0pll",
 	"core_bi_pll_test_se",
 };
 
@@ -237,40 +227,34 @@
 static const struct parent_map gcc_parent_map_14[] = {
 	{ P_XO, 0 },
 	{ P_GPLL0_OUT_MAIN, 1 },
-	{ P_GPLL4_OUT_AUX, 2 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
 static const char * const gcc_parent_names_14[] = {
 	"cxo",
 	"gpll0_out_main",
-	"gpll4_out_aux",
 	"core_bi_pll_test_se",
 };
 
 static const struct parent_map gcc_parent_map_15[] = {
 	{ P_XO, 0 },
-	{ P_GPLL0_OUT_AUX, 2 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
 static const char * const gcc_parent_names_15[] = {
 	"cxo",
-	"gpll0_out_aux",
 	"core_bi_pll_test_se",
 };
 
 static const struct parent_map gcc_parent_map_16[] = {
 	{ P_XO, 0 },
 	{ P_GPLL0_OUT_MAIN, 1 },
-	{ P_GPLL0_OUT_AUX, 2 },
 	{ P_CORE_BI_PLL_TEST_SE, 7 },
 };
 
 static const char * const gcc_parent_names_16[] = {
 	"cxo",
 	"gpll0_out_main",
-	"gpll0_out_aux",
 	"core_bi_pll_test_se",
 };
 
@@ -353,6 +337,7 @@
 /* 930MHz configuration */
 static const struct alpha_pll_config gpll3_config = {
 	.l = 48,
+	.alpha_hi = 0x70,
 	.alpha = 0x0,
 	.alpha_en_mask = BIT(24),
 	.post_div_mask = 0xf << 8,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sc7180.c
@@ -667,6 +667,7 @@
 		.name = "gcc_sdcc2_apps_clk_src",
 		.parent_data = gcc_parent_data_5,
 		.num_parents = ARRAY_SIZE(gcc_parent_data_5),
+		.flags = CLK_OPS_PARENT_ENABLE,
 		.ops = &clk_rcg2_floor_ops,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sc7280.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sc7280.c
@@ -2998,7 +2998,7 @@
 		.enable_mask = BIT(0),
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_cfg_noc_lpass_clk",
-			.ops = &clk_branch2_ops,
+			.ops = &clk_branch2_aon_ops,
 		},
 	},
 };
@@ -3571,6 +3571,10 @@
 	regmap_update_bits(regmap, 0x28004, BIT(0), BIT(0));
 	regmap_update_bits(regmap, 0x28014, BIT(0), BIT(0));
 	regmap_update_bits(regmap, 0x71004, BIT(0), BIT(0));
+	regmap_update_bits(regmap, 0x7100C, BIT(13), BIT(13));
+
+	/* FORCE_MEM_CORE_ON for ufs phy ice core clocks */
+	qcom_branch_set_force_mem_core(regmap, gcc_ufs_phy_ice_core_clk, true);
 
 	ret = qcom_cc_register_rcg_dfs(regmap, gcc_dfs_clocks,
 			ARRAY_SIZE(gcc_dfs_clocks));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sc8180x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sc8180x.c
@@ -143,6 +143,23 @@
 	},
 };
 
+static struct clk_alpha_pll gpll9 = {
+	.offset = 0x1c000,
+	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_TRION],
+	.clkr = {
+		.enable_reg = 0x52000,
+		.enable_mask = BIT(9),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gpll9",
+			.parent_data = &(const struct clk_parent_data) {
+				.fw_name = "bi_tcxo",
+			},
+			.num_parents = 1,
+			.ops = &clk_alpha_pll_fixed_trion_ops,
+		},
+	},
+};
+
 static const struct parent_map gcc_parent_map_0[] = {
 	{ P_BI_TCXO, 0 },
 	{ P_GPLL0_OUT_MAIN, 1 },
@@ -242,7 +259,7 @@
 static const struct clk_parent_data gcc_parents_7[] = {
 	{ .fw_name = "bi_tcxo", },
 	{ .hw = &gpll0.clkr.hw },
-	{ .name = "gppl9" },
+	{ .hw = &gpll9.clkr.hw },
 	{ .hw = &gpll4.clkr.hw },
 	{ .hw = &gpll0_out_even.clkr.hw },
 };
@@ -261,28 +278,6 @@
 	{ .hw = &gpll0_out_even.clkr.hw },
 };
 
-static const struct freq_tbl ftbl_gcc_cpuss_ahb_clk_src[] = {
-	F(19200000, P_BI_TCXO, 1, 0, 0),
-	F(50000000, P_GPLL0_OUT_MAIN, 12, 0, 0),
-	F(100000000, P_GPLL0_OUT_MAIN, 6, 0, 0),
-	{ }
-};
-
-static struct clk_rcg2 gcc_cpuss_ahb_clk_src = {
-	.cmd_rcgr = 0x48014,
-	.mnd_width = 0,
-	.hid_width = 5,
-	.parent_map = gcc_parent_map_0,
-	.freq_tbl = ftbl_gcc_cpuss_ahb_clk_src,
-	.clkr.hw.init = &(struct clk_init_data){
-		.name = "gcc_cpuss_ahb_clk_src",
-		.parent_data = gcc_parents_0,
-		.num_parents = ARRAY_SIZE(gcc_parents_0),
-		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
-	},
-};
-
 static const struct freq_tbl ftbl_gcc_emac_ptp_clk_src[] = {
 	F(19200000, P_BI_TCXO, 1, 0, 0),
 	F(50000000, P_GPLL0_OUT_EVEN, 6, 0, 0),
@@ -917,7 +912,7 @@
 	F(25000000, P_GPLL0_OUT_MAIN, 12, 1, 2),
 	F(50000000, P_GPLL0_OUT_MAIN, 12, 0, 0),
 	F(100000000, P_GPLL0_OUT_MAIN, 6, 0, 0),
-	F(200000000, P_GPLL0_OUT_MAIN, 3, 0, 0),
+	F(202000000, P_GPLL9_OUT_MAIN, 4, 0, 0),
 	{ }
 };
 
@@ -940,9 +935,8 @@
 	F(400000, P_BI_TCXO, 12, 1, 4),
 	F(9600000, P_BI_TCXO, 2, 0, 0),
 	F(19200000, P_BI_TCXO, 1, 0, 0),
-	F(37500000, P_GPLL0_OUT_MAIN, 16, 0, 0),
 	F(50000000, P_GPLL0_OUT_MAIN, 12, 0, 0),
-	F(75000000, P_GPLL0_OUT_MAIN, 8, 0, 0),
+	F(100000000, P_GPLL0_OUT_MAIN, 6, 0, 0),
 	{ }
 };
 
@@ -1600,25 +1594,6 @@
 	},
 };
 
-/* For CPUSS functionality the AHB clock needs to be left enabled */
-static struct clk_branch gcc_cpuss_ahb_clk = {
-	.halt_reg = 0x48000,
-	.halt_check = BRANCH_HALT_VOTED,
-	.clkr = {
-		.enable_reg = 0x52004,
-		.enable_mask = BIT(21),
-		.hw.init = &(struct clk_init_data){
-			.name = "gcc_cpuss_ahb_clk",
-			.parent_hws = (const struct clk_hw *[]){
-				      &gcc_cpuss_ahb_clk_src.clkr.hw
-			},
-			.num_parents = 1,
-			.flags = CLK_IS_CRITICAL | CLK_SET_RATE_PARENT,
-			.ops = &clk_branch2_ops,
-		},
-	},
-};
-
 static struct clk_branch gcc_cpuss_rbcpr_clk = {
 	.halt_reg = 0x48008,
 	.halt_check = BRANCH_HALT,
@@ -3151,25 +3126,6 @@
 	},
 };
 
-/* For CPUSS functionality the SYS NOC clock needs to be left enabled */
-static struct clk_branch gcc_sys_noc_cpuss_ahb_clk = {
-	.halt_reg = 0x4819c,
-	.halt_check = BRANCH_HALT_VOTED,
-	.clkr = {
-		.enable_reg = 0x52004,
-		.enable_mask = BIT(0),
-		.hw.init = &(struct clk_init_data){
-			.name = "gcc_sys_noc_cpuss_ahb_clk",
-			.parent_hws = (const struct clk_hw *[]){
-				      &gcc_cpuss_ahb_clk_src.clkr.hw
-			},
-			.num_parents = 1,
-			.flags = CLK_IS_CRITICAL | CLK_SET_RATE_PARENT,
-			.ops = &clk_branch2_ops,
-		},
-	},
-};
-
 static struct clk_branch gcc_tsif_ahb_clk = {
 	.halt_reg = 0x36004,
 	.halt_check = BRANCH_HALT,
@@ -4259,8 +4215,6 @@
 	[GCC_CFG_NOC_USB3_MP_AXI_CLK] = &gcc_cfg_noc_usb3_mp_axi_clk.clkr,
 	[GCC_CFG_NOC_USB3_PRIM_AXI_CLK] = &gcc_cfg_noc_usb3_prim_axi_clk.clkr,
 	[GCC_CFG_NOC_USB3_SEC_AXI_CLK] = &gcc_cfg_noc_usb3_sec_axi_clk.clkr,
-	[GCC_CPUSS_AHB_CLK] = &gcc_cpuss_ahb_clk.clkr,
-	[GCC_CPUSS_AHB_CLK_SRC] = &gcc_cpuss_ahb_clk_src.clkr,
 	[GCC_CPUSS_RBCPR_CLK] = &gcc_cpuss_rbcpr_clk.clkr,
 	[GCC_DDRSS_GPU_AXI_CLK] = &gcc_ddrss_gpu_axi_clk.clkr,
 	[GCC_DISP_HF_AXI_CLK] = &gcc_disp_hf_axi_clk.clkr,
@@ -4397,7 +4351,6 @@
 	[GCC_SDCC4_AHB_CLK] = &gcc_sdcc4_ahb_clk.clkr,
 	[GCC_SDCC4_APPS_CLK] = &gcc_sdcc4_apps_clk.clkr,
 	[GCC_SDCC4_APPS_CLK_SRC] = &gcc_sdcc4_apps_clk_src.clkr,
-	[GCC_SYS_NOC_CPUSS_AHB_CLK] = &gcc_sys_noc_cpuss_ahb_clk.clkr,
 	[GCC_TSIF_AHB_CLK] = &gcc_tsif_ahb_clk.clkr,
 	[GCC_TSIF_INACTIVITY_TIMERS_CLK] = &gcc_tsif_inactivity_timers_clk.clkr,
 	[GCC_TSIF_REF_CLK] = &gcc_tsif_ref_clk.clkr,
@@ -4484,6 +4437,7 @@
 	[GPLL1] = &gpll1.clkr,
 	[GPLL4] = &gpll4.clkr,
 	[GPLL7] = &gpll7.clkr,
+	[GPLL9] = &gpll9.clkr,
 };
 
 static const struct qcom_reset_map gcc_sc8180x_resets[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sdm845.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sdm845.c
@@ -3642,3 +3642,4 @@
 MODULE_DESCRIPTION("QTI GCC SDM845 Driver");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:gcc-sdm845");
+MODULE_SOFTDEP("pre: rpmhpd");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sm6115.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sm6115.c
@@ -53,11 +53,25 @@
 	{ 750000000, 1500000000, 1 },
 };
 
+static const u8 clk_alpha_pll_regs_offset[][PLL_OFF_MAX_REGS] = {
+	[CLK_ALPHA_PLL_TYPE_DEFAULT] =  {
+		[PLL_OFF_L_VAL] = 0x04,
+		[PLL_OFF_ALPHA_VAL] = 0x08,
+		[PLL_OFF_ALPHA_VAL_U] = 0x0c,
+		[PLL_OFF_TEST_CTL] = 0x10,
+		[PLL_OFF_TEST_CTL_U] = 0x14,
+		[PLL_OFF_USER_CTL] = 0x18,
+		[PLL_OFF_USER_CTL_U] = 0x1c,
+		[PLL_OFF_CONFIG_CTL] = 0x20,
+		[PLL_OFF_STATUS] = 0x24,
+	},
+};
+
 static struct clk_alpha_pll gpll0 = {
 	.offset = 0x0,
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(0),
@@ -83,7 +97,7 @@
 	.post_div_table = post_div_table_gpll0_out_aux2,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll0_out_aux2),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll0_out_aux2",
 		.parent_hws = (const struct clk_hw *[]){ &gpll0.clkr.hw },
@@ -115,7 +129,7 @@
 	.post_div_table = post_div_table_gpll0_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll0_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll0_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll0.clkr.hw },
@@ -137,7 +151,7 @@
 	.offset = 0xa000,
 	.vco_table = gpll10_vco,
 	.num_vco = ARRAY_SIZE(gpll10_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(10),
@@ -163,7 +177,7 @@
 	.post_div_table = post_div_table_gpll10_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll10_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll10_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll10.clkr.hw },
@@ -189,7 +203,7 @@
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
 	.flags = SUPPORTS_DYNAMIC_UPDATE,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(11),
@@ -215,7 +229,7 @@
 	.post_div_table = post_div_table_gpll11_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll11_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll11_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll11.clkr.hw },
@@ -229,7 +243,7 @@
 	.offset = 0x3000,
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(3),
@@ -248,7 +262,7 @@
 	.offset = 0x4000,
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(4),
@@ -274,7 +288,7 @@
 	.post_div_table = post_div_table_gpll4_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll4_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll4_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll4.clkr.hw },
@@ -287,7 +301,7 @@
 	.offset = 0x6000,
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(6),
@@ -313,7 +327,7 @@
 	.post_div_table = post_div_table_gpll6_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll6_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll6_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll6.clkr.hw },
@@ -326,7 +340,7 @@
 	.offset = 0x7000,
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr = {
 		.enable_reg = 0x79000,
 		.enable_mask = BIT(7),
@@ -352,7 +366,7 @@
 	.post_div_table = post_div_table_gpll7_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll7_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll7_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll7.clkr.hw },
@@ -380,7 +394,7 @@
 	.offset = 0x8000,
 	.vco_table = default_vco,
 	.num_vco = ARRAY_SIZE(default_vco),
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.flags = SUPPORTS_DYNAMIC_UPDATE,
 	.clkr = {
 		.enable_reg = 0x79000,
@@ -407,7 +421,7 @@
 	.post_div_table = post_div_table_gpll8_out_main,
 	.num_post_div = ARRAY_SIZE(post_div_table_gpll8_out_main),
 	.width = 4,
-	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
+	.regs = clk_alpha_pll_regs_offset[CLK_ALPHA_PLL_TYPE_DEFAULT],
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll8_out_main",
 		.parent_hws = (const struct clk_hw *[]){ &gpll8.clkr.hw },
@@ -706,7 +720,7 @@
 		.parent_data = gcc_parents_7,
 		.num_parents = ARRAY_SIZE(gcc_parents_7),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -727,7 +741,7 @@
 		.parent_data = gcc_parents_9,
 		.num_parents = ARRAY_SIZE(gcc_parents_9),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -750,7 +764,7 @@
 		.parent_data = gcc_parents_4,
 		.num_parents = ARRAY_SIZE(gcc_parents_4),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -765,7 +779,7 @@
 		.parent_data = gcc_parents_4,
 		.num_parents = ARRAY_SIZE(gcc_parents_4),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -780,7 +794,7 @@
 		.parent_data = gcc_parents_4,
 		.num_parents = ARRAY_SIZE(gcc_parents_4),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -802,7 +816,7 @@
 		.parent_data = gcc_parents_3,
 		.num_parents = ARRAY_SIZE(gcc_parents_3),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -817,7 +831,7 @@
 		.parent_data = gcc_parents_3,
 		.num_parents = ARRAY_SIZE(gcc_parents_3),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -832,7 +846,7 @@
 		.parent_data = gcc_parents_3,
 		.num_parents = ARRAY_SIZE(gcc_parents_3),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -847,7 +861,7 @@
 		.parent_data = gcc_parents_3,
 		.num_parents = ARRAY_SIZE(gcc_parents_3),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -869,7 +883,7 @@
 		.parent_data = gcc_parents_8,
 		.num_parents = ARRAY_SIZE(gcc_parents_8),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -893,7 +907,7 @@
 		.parent_data = gcc_parents_8,
 		.num_parents = ARRAY_SIZE(gcc_parents_8),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -928,7 +942,7 @@
 		.parent_data = gcc_parents_5,
 		.num_parents = ARRAY_SIZE(gcc_parents_5),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -953,7 +967,7 @@
 		.parent_data = gcc_parents_6,
 		.num_parents = ARRAY_SIZE(gcc_parents_6),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -968,7 +982,7 @@
 		.parent_data = gcc_parents_5,
 		.num_parents = ARRAY_SIZE(gcc_parents_5),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -983,7 +997,7 @@
 		.parent_data = gcc_parents_6,
 		.num_parents = ARRAY_SIZE(gcc_parents_6),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -998,7 +1012,7 @@
 		.parent_data = gcc_parents_5,
 		.num_parents = ARRAY_SIZE(gcc_parents_5),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1013,7 +1027,7 @@
 		.parent_data = gcc_parents_6,
 		.num_parents = ARRAY_SIZE(gcc_parents_6),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1036,7 +1050,7 @@
 		.parent_data = gcc_parents_10,
 		.num_parents = ARRAY_SIZE(gcc_parents_10),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1058,7 +1072,7 @@
 		.parent_data = gcc_parents_7,
 		.num_parents = ARRAY_SIZE(gcc_parents_7),
 		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1128,7 +1142,7 @@
 		.name = "gcc_pdm2_clk_src",
 		.parent_data = gcc_parents_0,
 		.num_parents = ARRAY_SIZE(gcc_parents_0),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1341,7 +1355,7 @@
 		.name = "gcc_ufs_phy_axi_clk_src",
 		.parent_data = gcc_parents_0,
 		.num_parents = ARRAY_SIZE(gcc_parents_0),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1363,7 +1377,7 @@
 		.name = "gcc_ufs_phy_ice_core_clk_src",
 		.parent_data = gcc_parents_0,
 		.num_parents = ARRAY_SIZE(gcc_parents_0),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1404,7 +1418,7 @@
 		.name = "gcc_ufs_phy_unipro_core_clk_src",
 		.parent_data = gcc_parents_0,
 		.num_parents = ARRAY_SIZE(gcc_parents_0),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1426,7 +1440,7 @@
 		.name = "gcc_usb30_prim_master_clk_src",
 		.parent_data = gcc_parents_0,
 		.num_parents = ARRAY_SIZE(gcc_parents_0),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
@@ -1495,7 +1509,7 @@
 		.parent_data = gcc_parents_13,
 		.num_parents = ARRAY_SIZE(gcc_parents_13),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_shared_ops,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sm6125.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sm6125.c
@@ -1121,7 +1121,7 @@
 		.name = "gcc_sdcc1_apps_clk_src",
 		.parent_data = gcc_parent_data_1,
 		.num_parents = ARRAY_SIZE(gcc_parent_data_1),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_floor_ops,
 	},
 };
 
@@ -1143,7 +1143,7 @@
 		.name = "gcc_sdcc1_ice_core_clk_src",
 		.parent_data = gcc_parent_data_0,
 		.num_parents = ARRAY_SIZE(gcc_parent_data_0),
-		.ops = &clk_rcg2_floor_ops,
+		.ops = &clk_rcg2_ops,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sm6350.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sm6350.c
@@ -99,8 +99,8 @@
 		.enable_mask = BIT(6),
 		.hw.init = &(struct clk_init_data){
 			.name = "gpll6",
-			.parent_hws = (const struct clk_hw*[]){
-				&gpll0.clkr.hw,
+			.parent_data = &(const struct clk_parent_data){
+				.fw_name = "bi_tcxo",
 			},
 			.num_parents = 1,
 			.ops = &clk_alpha_pll_fixed_fabia_ops,
@@ -123,7 +123,7 @@
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gpll6_out_even",
 		.parent_hws = (const struct clk_hw*[]){
-			&gpll0.clkr.hw,
+			&gpll6.clkr.hw,
 		},
 		.num_parents = 1,
 		.ops = &clk_alpha_pll_postdiv_fabia_ops,
@@ -138,8 +138,8 @@
 		.enable_mask = BIT(7),
 		.hw.init = &(struct clk_init_data){
 			.name = "gpll7",
-			.parent_hws = (const struct clk_hw*[]){
-				&gpll0.clkr.hw,
+			.parent_data = &(const struct clk_parent_data){
+				.fw_name = "bi_tcxo",
 			},
 			.num_parents = 1,
 			.ops = &clk_alpha_pll_fixed_fabia_ops,
@@ -181,6 +181,14 @@
 	{ .hw = &gpll0_out_odd.clkr.hw },
 };
 
+static const struct parent_map gcc_parent_map_3[] = {
+	{ P_BI_TCXO, 0 },
+};
+
+static const struct clk_parent_data gcc_parent_data_3[] = {
+	{ .fw_name = "bi_tcxo" },
+};
+
 static const struct parent_map gcc_parent_map_4[] = {
 	{ P_BI_TCXO, 0 },
 	{ P_GPLL0_OUT_MAIN, 1 },
@@ -640,6 +648,7 @@
 		.name = "gcc_sdcc2_apps_clk_src",
 		.parent_data = gcc_parent_data_8,
 		.num_parents = ARRAY_SIZE(gcc_parent_data_8),
+		.flags = CLK_OPS_PARENT_ENABLE,
 		.ops = &clk_rcg2_floor_ops,
 	},
 };
@@ -699,13 +708,12 @@
 	.cmd_rcgr = 0x3a0b0,
 	.mnd_width = 0,
 	.hid_width = 5,
+	.parent_map = gcc_parent_map_3,
 	.freq_tbl = ftbl_gcc_ufs_phy_phy_aux_clk_src,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gcc_ufs_phy_phy_aux_clk_src",
-		.parent_data = &(const struct clk_parent_data){
-			.fw_name = "bi_tcxo",
-		},
-		.num_parents = 1,
+		.parent_data = gcc_parent_data_3,
+		.num_parents = ARRAY_SIZE(gcc_parent_data_3),
 		.ops = &clk_rcg2_ops,
 	},
 };
@@ -762,13 +770,12 @@
 	.cmd_rcgr = 0x1a034,
 	.mnd_width = 0,
 	.hid_width = 5,
+	.parent_map = gcc_parent_map_3,
 	.freq_tbl = ftbl_gcc_usb30_prim_mock_utmi_clk_src,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "gcc_usb30_prim_mock_utmi_clk_src",
-		.parent_data = &(const struct clk_parent_data){
-			.fw_name = "bi_tcxo",
-		},
-		.num_parents = 1,
+		.parent_data = gcc_parent_data_3,
+		.num_parents = ARRAY_SIZE(gcc_parent_data_3),
 		.ops = &clk_rcg2_ops,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sm8150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sm8150.c
@@ -792,7 +792,7 @@
 		.name = "gcc_sdcc2_apps_clk_src",
 		.parent_data = gcc_parents_6,
 		.num_parents = ARRAY_SIZE(gcc_parents_6),
-		.flags = CLK_SET_RATE_PARENT,
+		.flags = CLK_OPS_PARENT_ENABLE,
 		.ops = &clk_rcg2_floor_ops,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sm8250.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sm8250.c
@@ -721,6 +721,7 @@
 		.name = "gcc_sdcc2_apps_clk_src",
 		.parent_data = gcc_parent_data_4,
 		.num_parents = ARRAY_SIZE(gcc_parent_data_4),
+		.flags = CLK_OPS_PARENT_ENABLE,
 		.ops = &clk_rcg2_floor_ops,
 	},
 };
@@ -3227,7 +3228,7 @@
 	.pd = {
 		.name = "pcie_0_gdsc",
 	},
-	.pwrsts = PWRSTS_OFF_ON,
+	.pwrsts = PWRSTS_RET_ON,
 };
 
 static struct gdsc pcie_1_gdsc = {
@@ -3235,7 +3236,7 @@
 	.pd = {
 		.name = "pcie_1_gdsc",
 	},
-	.pwrsts = PWRSTS_OFF_ON,
+	.pwrsts = PWRSTS_RET_ON,
 };
 
 static struct gdsc pcie_2_gdsc = {
@@ -3243,7 +3244,7 @@
 	.pd = {
 		.name = "pcie_2_gdsc",
 	},
-	.pwrsts = PWRSTS_OFF_ON,
+	.pwrsts = PWRSTS_RET_ON,
 };
 
 static struct gdsc ufs_card_gdsc = {
@@ -3267,7 +3268,7 @@
 	.pd = {
 		.name = "usb30_prim_gdsc",
 	},
-	.pwrsts = PWRSTS_OFF_ON,
+	.pwrsts = PWRSTS_RET_ON,
 };
 
 static struct gdsc usb30_sec_gdsc = {
@@ -3275,7 +3276,7 @@
 	.pd = {
 		.name = "usb30_sec_gdsc",
 	},
-	.pwrsts = PWRSTS_OFF_ON,
+	.pwrsts = PWRSTS_RET_ON,
 };
 
 static struct gdsc hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gcc-sm8350.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gcc-sm8350.c
@@ -16,6 +16,7 @@
 #include "clk-regmap.h"
 #include "clk-regmap-divider.h"
 #include "clk-regmap-mux.h"
+#include "clk-regmap-phy-mux.h"
 #include "gdsc.h"
 #include "reset.h"
 
@@ -166,26 +167,6 @@
 	{ .fw_name = "core_bi_pll_test_se" },
 };
 
-static const struct parent_map gcc_parent_map_4[] = {
-	{ P_PCIE_0_PIPE_CLK, 0 },
-	{ P_BI_TCXO, 2 },
-};
-
-static const struct clk_parent_data gcc_parent_data_4[] = {
-	{ .fw_name = "pcie_0_pipe_clk", },
-	{ .fw_name = "bi_tcxo" },
-};
-
-static const struct parent_map gcc_parent_map_5[] = {
-	{ P_PCIE_1_PIPE_CLK, 0 },
-	{ P_BI_TCXO, 2 },
-};
-
-static const struct clk_parent_data gcc_parent_data_5[] = {
-	{ .fw_name = "pcie_1_pipe_clk" },
-	{ .fw_name = "bi_tcxo" },
-};
-
 static const struct parent_map gcc_parent_map_6[] = {
 	{ P_BI_TCXO, 0 },
 	{ P_GCC_GPLL0_OUT_MAIN, 1 },
@@ -288,32 +269,30 @@
 	{ .fw_name = "bi_tcxo" },
 };
 
-static struct clk_regmap_mux gcc_pcie_0_pipe_clk_src = {
+static struct clk_regmap_phy_mux gcc_pcie_0_pipe_clk_src = {
 	.reg = 0x6b054,
-	.shift = 0,
-	.width = 2,
-	.parent_map = gcc_parent_map_4,
 	.clkr = {
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_pcie_0_pipe_clk_src",
-			.parent_data = gcc_parent_data_4,
-			.num_parents = ARRAY_SIZE(gcc_parent_data_4),
-			.ops = &clk_regmap_mux_closest_ops,
+			.parent_data = &(const struct clk_parent_data){
+				.fw_name = "pcie_0_pipe_clk",
+			},
+			.num_parents = 1,
+			.ops = &clk_regmap_phy_mux_ops,
 		},
 	},
 };
 
-static struct clk_regmap_mux gcc_pcie_1_pipe_clk_src = {
+static struct clk_regmap_phy_mux gcc_pcie_1_pipe_clk_src = {
 	.reg = 0x8d054,
-	.shift = 0,
-	.width = 2,
-	.parent_map = gcc_parent_map_5,
 	.clkr = {
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_pcie_1_pipe_clk_src",
-			.parent_data = gcc_parent_data_5,
-			.num_parents = ARRAY_SIZE(gcc_parent_data_5),
-			.ops = &clk_regmap_mux_closest_ops,
+			.parent_data = &(const struct clk_parent_data){
+				.fw_name = "pcie_1_pipe_clk",
+			},
+			.num_parents = 1,
+			.ops = &clk_regmap_phy_mux_ops,
 		},
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gdsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gdsc.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (c) 2015, 2017-2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2015, 2017-2018, 2022, The Linux Foundation. All rights reserved.
  */
 
 #include <linux/bitops.h>
@@ -34,9 +34,14 @@
 #define CFG_GDSCR_OFFSET		0x4
 
 /* Wait 2^n CXO cycles between all states. Here, n=2 (4 cycles). */
-#define EN_REST_WAIT_VAL	(0x2 << 20)
-#define EN_FEW_WAIT_VAL		(0x8 << 16)
-#define CLK_DIS_WAIT_VAL	(0x2 << 12)
+#define EN_REST_WAIT_VAL	0x2
+#define EN_FEW_WAIT_VAL		0x8
+#define CLK_DIS_WAIT_VAL	0x2
+
+/* Transition delay shifts */
+#define EN_REST_WAIT_SHIFT	20
+#define EN_FEW_WAIT_SHIFT	16
+#define CLK_DIS_WAIT_SHIFT	12
 
 #define RETAIN_MEM		BIT(14)
 #define RETAIN_PERIPH		BIT(13)
@@ -341,7 +346,18 @@
 	 */
 	mask = HW_CONTROL_MASK | SW_OVERRIDE_MASK |
 	       EN_REST_WAIT_MASK | EN_FEW_WAIT_MASK | CLK_DIS_WAIT_MASK;
-	val = EN_REST_WAIT_VAL | EN_FEW_WAIT_VAL | CLK_DIS_WAIT_VAL;
+
+	if (!sc->en_rest_wait_val)
+		sc->en_rest_wait_val = EN_REST_WAIT_VAL;
+	if (!sc->en_few_wait_val)
+		sc->en_few_wait_val = EN_FEW_WAIT_VAL;
+	if (!sc->clk_dis_wait_val)
+		sc->clk_dis_wait_val = CLK_DIS_WAIT_VAL;
+
+	val = sc->en_rest_wait_val << EN_REST_WAIT_SHIFT |
+		sc->en_few_wait_val << EN_FEW_WAIT_SHIFT |
+		sc->clk_dis_wait_val << CLK_DIS_WAIT_SHIFT;
+
 	ret = regmap_update_bits(sc->regmap, sc->gdscr, mask, val);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gdsc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gdsc.h
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- * Copyright (c) 2015, 2017-2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2015, 2017-2018, 2022, The Linux Foundation. All rights reserved.
  */
 
 #ifndef __QCOM_GDSC_H__
@@ -22,6 +22,9 @@
  * @cxcs: offsets of branch registers to toggle mem/periph bits in
  * @cxc_count: number of @cxcs
  * @pwrsts: Possible powerdomain power states
+ * @en_rest_wait_val: transition delay value for receiving enr ack signal
+ * @en_few_wait_val: transition delay value for receiving enf ack signal
+ * @clk_dis_wait_val: transition delay value for halting clock
  * @resets: ids of resets associated with this gdsc
  * @reset_count: number of @resets
  * @rcdev: reset controller
@@ -35,6 +38,9 @@
 	unsigned int			clamp_io_ctrl;
 	unsigned int			*cxcs;
 	unsigned int			cxc_count;
+	unsigned int			en_rest_wait_val;
+	unsigned int			en_few_wait_val;
+	unsigned int			clk_dis_wait_val;
 	const u8			pwrsts;
 /* Powerdomain allowable state bitfields */
 #define PWRSTS_OFF		BIT(0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gpucc-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gpucc-sc7180.c
@@ -21,8 +21,6 @@
 #define CX_GMU_CBCR_SLEEP_SHIFT		4
 #define CX_GMU_CBCR_WAKE_MASK		0xF
 #define CX_GMU_CBCR_WAKE_SHIFT		8
-#define CLK_DIS_WAIT_SHIFT		12
-#define CLK_DIS_WAIT_MASK		(0xf << CLK_DIS_WAIT_SHIFT)
 
 enum {
 	P_BI_TCXO,
@@ -160,6 +158,7 @@
 static struct gdsc cx_gdsc = {
 	.gdscr = 0x106c,
 	.gds_hw_ctrl = 0x1540,
+	.clk_dis_wait_val = 8,
 	.pd = {
 		.name = "cx_gdsc",
 	},
@@ -242,10 +241,6 @@
 	value = 0xF << CX_GMU_CBCR_WAKE_SHIFT | 0xF << CX_GMU_CBCR_SLEEP_SHIFT;
 	regmap_update_bits(regmap, 0x1098, mask, value);
 
-	/* Configure clk_dis_wait for gpu_cx_gdsc */
-	regmap_update_bits(regmap, 0x106c, CLK_DIS_WAIT_MASK,
-						8 << CLK_DIS_WAIT_SHIFT);
-
 	return qcom_cc_really_probe(pdev, &gpu_cc_sc7180_desc, regmap);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gpucc-sc7280.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gpucc-sc7280.c
@@ -463,6 +463,7 @@
 	 */
 	regmap_update_bits(regmap, 0x1170, BIT(0), BIT(0));
 	regmap_update_bits(regmap, 0x1098, BIT(0), BIT(0));
+	regmap_update_bits(regmap, 0x1098, BIT(13), BIT(13));
 
 	return qcom_cc_really_probe(pdev, &gpu_cc_sc7280_desc, regmap);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gpucc-sdm845.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gpucc-sdm845.c
@@ -22,8 +22,6 @@
 #define CX_GMU_CBCR_SLEEP_SHIFT		4
 #define CX_GMU_CBCR_WAKE_MASK		0xf
 #define CX_GMU_CBCR_WAKE_SHIFT		8
-#define CLK_DIS_WAIT_SHIFT		12
-#define CLK_DIS_WAIT_MASK		(0xf << CLK_DIS_WAIT_SHIFT)
 
 enum {
 	P_BI_TCXO,
@@ -121,6 +119,7 @@
 static struct gdsc gpu_cx_gdsc = {
 	.gdscr = 0x106c,
 	.gds_hw_ctrl = 0x1540,
+	.clk_dis_wait_val = 0x8,
 	.pd = {
 		.name = "gpu_cx_gdsc",
 	},
@@ -193,10 +192,6 @@
 	value = 0xf << CX_GMU_CBCR_WAKE_SHIFT | 0xf << CX_GMU_CBCR_SLEEP_SHIFT;
 	regmap_update_bits(regmap, 0x1098, mask, value);
 
-	/* Configure clk_dis_wait for gpu_cx_gdsc */
-	regmap_update_bits(regmap, 0x106c, CLK_DIS_WAIT_MASK,
-						8 << CLK_DIS_WAIT_SHIFT);
-
 	return qcom_cc_really_probe(pdev, &gpu_cc_sdm845_desc, regmap);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/gpucc-sm8150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/gpucc-sm8150.c
@@ -37,8 +37,8 @@
 	.config_ctl_hi_val = 0x00002267,
 	.config_ctl_hi1_val = 0x00000024,
 	.test_ctl_val = 0x00000000,
-	.test_ctl_hi_val = 0x00000002,
-	.test_ctl_hi1_val = 0x00000000,
+	.test_ctl_hi_val = 0x00000000,
+	.test_ctl_hi1_val = 0x00000020,
 	.user_ctl_val = 0x00000000,
 	.user_ctl_hi_val = 0x00000805,
 	.user_ctl_hi1_val = 0x000000d0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/lpasscorecc-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/lpasscorecc-sc7180.c
@@ -356,7 +356,7 @@
 	.num_gdscs = ARRAY_SIZE(lpass_audio_hm_sc7180_gdscs),
 };
 
-static int lpass_create_pm_clks(struct platform_device *pdev)
+static int lpass_setup_runtime_pm(struct platform_device *pdev)
 {
 	int ret;
 
@@ -375,7 +375,7 @@
 	if (ret < 0)
 		dev_err(&pdev->dev, "failed to acquire iface clock\n");
 
-	return ret;
+	return pm_runtime_resume_and_get(&pdev->dev);
 }
 
 static int lpass_core_cc_sc7180_probe(struct platform_device *pdev)
@@ -384,7 +384,7 @@
 	struct regmap *regmap;
 	int ret;
 
-	ret = lpass_create_pm_clks(pdev);
+	ret = lpass_setup_runtime_pm(pdev);
 	if (ret)
 		return ret;
 
@@ -392,12 +392,14 @@
 	desc = &lpass_audio_hm_sc7180_desc;
 	ret = qcom_cc_probe_by_index(pdev, 1, desc);
 	if (ret)
-		return ret;
+		goto exit;
 
 	lpass_core_cc_sc7180_regmap_config.name = "lpass_core_cc";
 	regmap = qcom_cc_map(pdev, &lpass_core_cc_sc7180_desc);
-	if (IS_ERR(regmap))
-		return PTR_ERR(regmap);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		goto exit;
+	}
 
 	/*
 	 * Keep the CLK always-ON
@@ -415,6 +417,7 @@
 	ret = qcom_cc_really_probe(pdev, &lpass_core_cc_sc7180_desc, regmap);
 
 	pm_runtime_mark_last_busy(&pdev->dev);
+exit:
 	pm_runtime_put_autosuspend(&pdev->dev);
 
 	return ret;
@@ -425,14 +428,19 @@
 	const struct qcom_cc_desc *desc;
 	int ret;
 
-	ret = lpass_create_pm_clks(pdev);
+	ret = lpass_setup_runtime_pm(pdev);
 	if (ret)
 		return ret;
 
 	lpass_core_cc_sc7180_regmap_config.name = "lpass_hm_core";
 	desc = &lpass_core_hm_sc7180_desc;
 
-	return qcom_cc_probe_by_index(pdev, 0, desc);
+	ret = qcom_cc_probe_by_index(pdev, 0, desc);
+
+	pm_runtime_mark_last_busy(&pdev->dev);
+	pm_runtime_put_autosuspend(&pdev->dev);
+
+	return ret;
 }
 
 static const struct of_device_id lpass_hm_sc7180_match_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/mmcc-apq8084.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/mmcc-apq8084.c
@@ -333,6 +333,7 @@
 	F(333430000, P_MMPLL1, 3.5, 0, 0),
 	F(400000000, P_MMPLL0, 2, 0, 0),
 	F(466800000, P_MMPLL1, 2.5, 0, 0),
+	{ }
 };
 
 static struct clk_rcg2 mmss_axi_clk_src = {
@@ -357,6 +358,7 @@
 	F(150000000, P_GPLL0, 4, 0, 0),
 	F(228570000, P_MMPLL0, 3.5, 0, 0),
 	F(320000000, P_MMPLL0, 2.5, 0, 0),
+	{ }
 };
 
 static struct clk_rcg2 ocmemnoc_clk_src = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/mmcc-msm8974.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/mmcc-msm8974.c
@@ -267,6 +267,7 @@
 	F(291750000, P_MMPLL1, 4, 0, 0),
 	F(400000000, P_MMPLL0, 2, 0, 0),
 	F(466800000, P_MMPLL1, 2.5, 0, 0),
+	{ }
 };
 
 static struct clk_rcg2 mmss_axi_clk_src = {
@@ -291,6 +292,7 @@
 	F(150000000, P_GPLL0, 4, 0, 0),
 	F(291750000, P_MMPLL1, 4, 0, 0),
 	F(400000000, P_MMPLL0, 2, 0, 0),
+	{ }
 };
 
 static struct clk_rcg2 ocmemnoc_clk_src = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/mmcc-msm8998.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/mmcc-msm8998.c
@@ -2487,6 +2487,7 @@
 
 static struct clk_branch mnoc_ahb_clk = {
 	.halt_reg = 0x5024,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x5024,
 		.enable_mask = BIT(0),
@@ -2502,6 +2503,7 @@
 
 static struct clk_branch bimc_smmu_ahb_clk = {
 	.halt_reg = 0xe004,
+	.halt_check = BRANCH_HALT_SKIP,
 	.hwcg_reg = 0xe004,
 	.hwcg_bit = 1,
 	.clkr = {
@@ -2519,6 +2521,7 @@
 
 static struct clk_branch bimc_smmu_axi_clk = {
 	.halt_reg = 0xe008,
+	.halt_check = BRANCH_HALT_SKIP,
 	.hwcg_reg = 0xe008,
 	.hwcg_bit = 1,
 	.clkr = {
@@ -2584,6 +2587,8 @@
 
 static struct gdsc video_top_gdsc = {
 	.gdscr = 0x1024,
+	.cxcs = (unsigned int []){ 0x1028, 0x1034, 0x1038 },
+	.cxc_count = 3,
 	.pd = {
 		.name = "video_top",
 	},
@@ -2592,20 +2597,26 @@
 
 static struct gdsc video_subcore0_gdsc = {
 	.gdscr = 0x1040,
+	.cxcs = (unsigned int []){ 0x1048 },
+	.cxc_count = 1,
 	.pd = {
 		.name = "video_subcore0",
 	},
 	.parent = &video_top_gdsc.pd,
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = HW_CTRL,
 };
 
 static struct gdsc video_subcore1_gdsc = {
 	.gdscr = 0x1044,
+	.cxcs = (unsigned int []){ 0x104c },
+	.cxc_count = 1,
 	.pd = {
 		.name = "video_subcore1",
 	},
 	.parent = &video_top_gdsc.pd,
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = HW_CTRL,
 };
 
 static struct gdsc mdss_gdsc = {
@@ -2659,11 +2670,13 @@
 static struct gdsc bimc_smmu_gdsc = {
 	.gdscr = 0xe020,
 	.gds_hw_ctrl = 0xe024,
+	.cxcs = (unsigned int []){ 0xe008 },
+	.cxc_count = 1,
 	.pd = {
 		.name = "bimc_smmu",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
-	.flags = HW_CTRL | ALWAYS_ON,
+	.flags = VOTABLE,
 };
 
 static struct clk_regmap *mmcc_msm8998_clocks[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/mmcc-sdm660.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/mmcc-sdm660.c
@@ -2544,7 +2544,7 @@
 
 static struct clk_branch video_subcore0_clk = {
 	.halt_reg = 0x1048,
-	.halt_check = BRANCH_HALT,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x1048,
 		.enable_mask = BIT(0),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/mss-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/mss-sc7180.c
@@ -87,11 +87,22 @@
 		return ret;
 	}
 
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret)
+		return ret;
+
 	ret = qcom_cc_probe(pdev, &mss_sc7180_desc);
 	if (ret < 0)
-		return ret;
+		goto err_put_rpm;
+
+	pm_runtime_put(&pdev->dev);
 
 	return 0;
+
+err_put_rpm:
+	pm_runtime_put_sync(&pdev->dev);
+
+	return ret;
 }
 
 static const struct dev_pm_ops mss_sc7180_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/q6sstop-qcs404.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/q6sstop-qcs404.c
@@ -173,21 +173,32 @@
 		return ret;
 	}
 
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret)
+		return ret;
+
 	q6sstop_regmap_config.name = "q6sstop_tcsr";
 	desc = &tcsr_qcs404_desc;
 
 	ret = qcom_cc_probe_by_index(pdev, 1, desc);
 	if (ret)
-		return ret;
+		goto err_put_rpm;
 
 	q6sstop_regmap_config.name = "q6sstop_cc";
 	desc = &q6sstop_qcs404_desc;
 
 	ret = qcom_cc_probe_by_index(pdev, 0, desc);
 	if (ret)
-		return ret;
+		goto err_put_rpm;
+
+	pm_runtime_put(&pdev->dev);
 
 	return 0;
+
+err_put_rpm:
+	pm_runtime_put_sync(&pdev->dev);
+
+	return ret;
 }
 
 static const struct dev_pm_ops q6sstopcc_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/reset.c
@@ -13,14 +13,17 @@
 
 static int qcom_reset(struct reset_controller_dev *rcdev, unsigned long id)
 {
+	struct qcom_reset_controller *rst = to_qcom_reset_controller(rcdev);
+
 	rcdev->ops->assert(rcdev, id);
-	udelay(1);
+	fsleep(rst->reset_map[id].udelay ?: 1); /* use 1 us as default */
+
 	rcdev->ops->deassert(rcdev, id);
 	return 0;
 }
 
-static int
-qcom_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)
+static int qcom_reset_set_assert(struct reset_controller_dev *rcdev,
+				 unsigned long id, bool assert)
 {
 	struct qcom_reset_controller *rst;
 	const struct qcom_reset_map *map;
@@ -28,23 +31,24 @@
 
 	rst = to_qcom_reset_controller(rcdev);
 	map = &rst->reset_map[id];
-	mask = BIT(map->bit);
+	mask = map->bitmask ? map->bitmask : BIT(map->bit);
+
+	regmap_update_bits(rst->regmap, map->reg, mask, assert ? mask : 0);
+
+	/* Read back the register to ensure write completion, ignore the value */
+	regmap_read(rst->regmap, map->reg, &mask);
 
-	return regmap_update_bits(rst->regmap, map->reg, mask, mask);
+	return 0;
 }
 
-static int
-qcom_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+static int qcom_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)
 {
-	struct qcom_reset_controller *rst;
-	const struct qcom_reset_map *map;
-	u32 mask;
-
-	rst = to_qcom_reset_controller(rcdev);
-	map = &rst->reset_map[id];
-	mask = BIT(map->bit);
+	return qcom_reset_set_assert(rcdev, id, true);
+}
 
-	return regmap_update_bits(rst->regmap, map->reg, mask, 0);
+static int qcom_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	return qcom_reset_set_assert(rcdev, id, false);
 }
 
 const struct reset_control_ops qcom_reset_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/reset.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/reset.h
@@ -11,6 +11,8 @@
 struct qcom_reset_map {
 	unsigned int reg;
 	u8 bit;
+	u8 udelay;
+	u32 bitmask;
 };
 
 struct regmap;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/turingcc-qcs404.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/turingcc-qcs404.c
@@ -124,11 +124,22 @@
 		return ret;
 	}
 
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret)
+		return ret;
+
 	ret = qcom_cc_probe(pdev, &turingcc_desc);
 	if (ret < 0)
-		return ret;
+		goto err_put_rpm;
+
+	pm_runtime_put(&pdev->dev);
 
 	return 0;
+
+err_put_rpm:
+	pm_runtime_put_sync(&pdev->dev);
+
+	return ret;
 }
 
 static const struct dev_pm_ops turingcc_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/qcom/videocc-sm8150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/qcom/videocc-sm8150.c
@@ -33,6 +33,7 @@
 	.config_ctl_val = 0x20485699,
 	.config_ctl_hi_val = 0x00002267,
 	.config_ctl_hi1_val = 0x00000024,
+	.test_ctl_hi1_val = 0x00000020,
 	.user_ctl_val = 0x00000000,
 	.user_ctl_hi_val = 0x00000805,
 	.user_ctl_hi1_val = 0x000000D0,
@@ -214,6 +215,10 @@
 
 static const struct qcom_reset_map video_cc_sm8150_resets[] = {
 	[VIDEO_CC_MVSC_CORE_CLK_BCR] = { 0x850, 2 },
+	[VIDEO_CC_INTERFACE_BCR] = { 0x8f0 },
+	[VIDEO_CC_MVS0_BCR] = { 0x870 },
+	[VIDEO_CC_MVS1_BCR] = { 0x8b0 },
+	[VIDEO_CC_MVSC_BCR] = { 0x810 },
 };
 
 static const struct qcom_cc_desc video_cc_sm8150_desc = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/renesas/r9a06g032-clocks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/renesas/r9a06g032-clocks.c
@@ -286,8 +286,8 @@
 		.name = "uart_group_012",
 		.type = K_BITSEL,
 		.source = 1 + R9A06G032_DIV_UART,
-		/* R9A06G032_SYSCTRL_REG_PWRCTRL_PG1_PR2 */
-		.dual.sel = ((0xec / 4) << 5) | 24,
+		/* R9A06G032_SYSCTRL_REG_PWRCTRL_PG0_0 */
+		.dual.sel = ((0x34 / 4) << 5) | 30,
 		.dual.group = 0,
 	},
 	{
@@ -295,8 +295,8 @@
 		.name = "uart_group_34567",
 		.type = K_BITSEL,
 		.source = 1 + R9A06G032_DIV_P2_PG,
-		/* R9A06G032_SYSCTRL_REG_PWRCTRL_PG0_0 */
-		.dual.sel = ((0x34 / 4) << 5) | 30,
+		/* R9A06G032_SYSCTRL_REG_PWRCTRL_PG1_PR2 */
+		.dual.sel = ((0xec / 4) << 5) | 24,
 		.dual.group = 1,
 	},
 	D_UGATE(CLK_UART0, "clk_uart0", UART_GROUP_012, 0, 0, 0x1b2, 0x1b3, 0x1b4, 0x1b5),
@@ -386,7 +386,7 @@
 	int error;
 	int index;
 
-	while (!of_parse_phandle_with_args(np, "clocks", "#clock-cells", i,
+	while (!of_parse_phandle_with_args(np, "clocks", "#clock-cells", i++,
 					   &clkspec)) {
 		if (clkspec.np != pd->dev.of_node)
 			continue;
@@ -399,7 +399,6 @@
 			if (error)
 				return error;
 		}
-		i++;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/renesas/r9a07g044-cpg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/renesas/r9a07g044-cpg.c
@@ -61,8 +61,8 @@
 	DEF_FIXED(".osc", R9A07G044_OSCCLK, CLK_EXTAL, 1, 1),
 	DEF_FIXED(".osc_div1000", CLK_OSC_DIV1000, CLK_EXTAL, 1, 1000),
 	DEF_SAMPLL(".pll1", CLK_PLL1, CLK_EXTAL, PLL146_CONF(0)),
-	DEF_FIXED(".pll2", CLK_PLL2, CLK_EXTAL, 133, 2),
-	DEF_FIXED(".pll3", CLK_PLL3, CLK_EXTAL, 133, 2),
+	DEF_FIXED(".pll2", CLK_PLL2, CLK_EXTAL, 200, 3),
+	DEF_FIXED(".pll3", CLK_PLL3, CLK_EXTAL, 200, 3),
 
 	DEF_FIXED(".pll2_div2", CLK_PLL2_DIV2, CLK_PLL2, 1, 2),
 	DEF_FIXED(".pll2_div16", CLK_PLL2_DIV16, CLK_PLL2, 1, 16),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/renesas/renesas-cpg-mssr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/renesas/renesas-cpg-mssr.c
@@ -911,9 +911,8 @@
 		}
 
 		if (!i)
-			dev_warn(dev, "Failed to enable %s%u[0x%x]\n",
-				 priv->reg_layout == CLK_REG_LAYOUT_RZ_A ?
-				 "STB" : "SMSTP", reg, oldval & mask);
+			dev_warn(dev, "Failed to enable SMSTP%u[0x%x]\n", reg,
+				 oldval & mask);
 	}
 
 	return 0;
@@ -957,7 +956,6 @@
 		goto out_err;
 	}
 
-	cpg_mssr_priv = priv;
 	priv->num_core_clks = info->num_total_core_clks;
 	priv->num_mod_clks = info->num_hw_mod_clks;
 	priv->last_dt_core_clk = info->last_dt_core_clk;
@@ -987,6 +985,8 @@
 	if (error)
 		goto out_err;
 
+	cpg_mssr_priv = priv;
+
 	return 0;
 
 out_err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/renesas/rzg2l-cpg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/renesas/rzg2l-cpg.c
@@ -11,6 +11,7 @@
  * Copyright (C) 2015 Renesas Electronics Corp.
  */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/clk/renesas.h>
@@ -37,14 +38,13 @@
 #define WARN_DEBUG(x)	do { } while (0)
 #endif
 
-#define DIV_RSMASK(v, s, m)	((v >> s) & m)
 #define GET_SHIFT(val)		((val >> 12) & 0xff)
 #define GET_WIDTH(val)		((val >> 8) & 0xf)
 
-#define KDIV(val)		DIV_RSMASK(val, 16, 0xffff)
-#define MDIV(val)		DIV_RSMASK(val, 6, 0x3ff)
-#define PDIV(val)		DIV_RSMASK(val, 0, 0x3f)
-#define SDIV(val)		DIV_RSMASK(val, 0, 0x7)
+#define KDIV(val)		((s16)FIELD_GET(GENMASK(31, 16), val))
+#define MDIV(val)		FIELD_GET(GENMASK(15, 6), val)
+#define PDIV(val)		FIELD_GET(GENMASK(5, 0), val)
+#define SDIV(val)		FIELD_GET(GENMASK(2, 0), val)
 
 #define CLK_ON_R(reg)		(reg)
 #define CLK_MON_R(reg)		(0x180 + (reg))
@@ -146,18 +146,18 @@
 	struct pll_clk *pll_clk = to_pll(hw);
 	struct rzg2l_cpg_priv *priv = pll_clk->priv;
 	unsigned int val1, val2;
-	unsigned int mult = 1;
-	unsigned int div = 1;
+	u64 rate;
 
 	if (pll_clk->type != CLK_TYPE_SAM_PLL)
 		return parent_rate;
 
 	val1 = readl(priv->base + GET_REG_SAMPLL_CLK1(pll_clk->conf));
 	val2 = readl(priv->base + GET_REG_SAMPLL_CLK2(pll_clk->conf));
-	mult = MDIV(val1) + KDIV(val1) / 65536;
-	div = PDIV(val1) * (1 << SDIV(val2));
 
-	return DIV_ROUND_CLOSEST_ULL((u64)parent_rate * mult, div);
+	rate = mul_u64_u32_shr(parent_rate, (MDIV(val1) << 16) + KDIV(val1),
+			       16 + SDIV(val2));
+
+	return DIV_ROUND_CLOSEST_ULL(rate, PDIV(val1));
 }
 
 static const struct clk_ops rzg2l_cpg_pll_ops = {
@@ -638,10 +638,16 @@
 		pm_clk_destroy(dev);
 }
 
+static void rzg2l_cpg_genpd_remove(void *data)
+{
+	pm_genpd_remove(data);
+}
+
 static int __init rzg2l_cpg_add_clk_domain(struct device *dev)
 {
 	struct device_node *np = dev->of_node;
 	struct generic_pm_domain *genpd;
+	int ret;
 
 	genpd = devm_kzalloc(dev, sizeof(*genpd), GFP_KERNEL);
 	if (!genpd)
@@ -652,10 +658,15 @@
 		       GENPD_FLAG_ACTIVE_WAKEUP;
 	genpd->attach_dev = rzg2l_cpg_attach_dev;
 	genpd->detach_dev = rzg2l_cpg_detach_dev;
-	pm_genpd_init(genpd, &pm_domain_always_on_gov, false);
+	ret = pm_genpd_init(genpd, &pm_domain_always_on_gov, false);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(dev, rzg2l_cpg_genpd_remove, genpd);
+	if (ret)
+		return ret;
 
-	of_genpd_add_provider_simple(np, genpd);
-	return 0;
+	return of_genpd_add_provider_simple(np, genpd);
 }
 
 static int __init rzg2l_cpg_probe(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk-pll.c
@@ -981,6 +981,7 @@
 	return mux_clk;
 
 err_pll:
+	kfree(pll->rate_table);
 	clk_unregister(mux_clk);
 	mux_clk = pll_clk;
 err_mux:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk-rk3128.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk-rk3128.c
@@ -490,7 +490,7 @@
 	GATE(HCLK_I2S_2CH, "hclk_i2s_2ch", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS),
 	GATE(0, "hclk_usb_peri", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 13, GFLAGS),
 	GATE(HCLK_HOST2, "hclk_host2", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 3, GFLAGS),
-	GATE(HCLK_OTG, "hclk_otg", "hclk_peri", 0, RK2928_CLKGATE_CON(3), 13, GFLAGS),
+	GATE(HCLK_OTG, "hclk_otg", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 13, GFLAGS),
 	GATE(0, "hclk_peri_ahb", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 14, GFLAGS),
 	GATE(HCLK_SPDIF, "hclk_spdif", "hclk_peri", 0, RK2928_CLKGATE_CON(10), 9, GFLAGS),
 	GATE(HCLK_TSP, "hclk_tsp", "hclk_peri", 0, RK2928_CLKGATE_CON(10), 12, GFLAGS),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk-rk3228.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk-rk3228.c
@@ -409,7 +409,7 @@
 			RK2928_CLKSEL_CON(29), 0, 3, DFLAGS),
 	DIV(0, "sclk_vop_pre", "sclk_vop_src", 0,
 			RK2928_CLKSEL_CON(27), 8, 8, DFLAGS),
-	MUX(DCLK_VOP, "dclk_vop", mux_dclk_vop_p, 0,
+	MUX(DCLK_VOP, "dclk_vop", mux_dclk_vop_p, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
 			RK2928_CLKSEL_CON(27), 1, 1, MFLAGS),
 
 	FACTOR(0, "xin12m", "xin24m", 0, 1, 2),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk-rk3328.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk-rk3328.c
@@ -201,7 +201,7 @@
 				    "gpll_peri",
 				    "hdmiphy_peri" };
 PNAME(mux_ref_usb3otg_src_p)	= { "xin24m",
-				    "clk_usb3otg_ref" };
+				    "clk_ref_usb3otg_src" };
 PNAME(mux_xin24m_32k_p)		= { "xin24m",
 				    "clk_rtc32k" };
 PNAME(mux_mac2io_src_p)		= { "clk_mac2io_src",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk-rk3399.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk-rk3399.c
@@ -1263,7 +1263,7 @@
 			RK3399_CLKSEL_CON(56), 6, 2, MFLAGS,
 			RK3399_CLKGATE_CON(10), 7, GFLAGS),
 
-	COMPOSITE_NOGATE(SCLK_CIF_OUT, "clk_cifout", mux_clk_cif_p, 0,
+	COMPOSITE_NOGATE(SCLK_CIF_OUT, "clk_cifout", mux_clk_cif_p, CLK_SET_RATE_PARENT,
 			 RK3399_CLKSEL_CON(56), 5, 1, MFLAGS, 0, 5, DFLAGS),
 
 	/* gic */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk-rk3568.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk-rk3568.c
@@ -1038,13 +1038,13 @@
 			RK3568_CLKGATE_CON(20), 8, GFLAGS),
 	GATE(HCLK_VOP, "hclk_vop", "hclk_vo", 0,
 			RK3568_CLKGATE_CON(20), 9, GFLAGS),
-	COMPOSITE(DCLK_VOP0, "dclk_vop0", hpll_vpll_gpll_cpll_p, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+	COMPOSITE(DCLK_VOP0, "dclk_vop0", hpll_vpll_gpll_cpll_p, CLK_SET_RATE_NO_REPARENT,
 			RK3568_CLKSEL_CON(39), 10, 2, MFLAGS, 0, 8, DFLAGS,
 			RK3568_CLKGATE_CON(20), 10, GFLAGS),
-	COMPOSITE(DCLK_VOP1, "dclk_vop1", hpll_vpll_gpll_cpll_p, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+	COMPOSITE(DCLK_VOP1, "dclk_vop1", hpll_vpll_gpll_cpll_p, CLK_SET_RATE_NO_REPARENT,
 			RK3568_CLKSEL_CON(40), 10, 2, MFLAGS, 0, 8, DFLAGS,
 			RK3568_CLKGATE_CON(20), 11, GFLAGS),
-	COMPOSITE(DCLK_VOP2, "dclk_vop2", hpll_vpll_gpll_cpll_p, 0,
+	COMPOSITE(DCLK_VOP2, "dclk_vop2", hpll_vpll_gpll_cpll_p, CLK_SET_RATE_NO_REPARENT,
 			RK3568_CLKSEL_CON(41), 10, 2, MFLAGS, 0, 8, DFLAGS,
 			RK3568_CLKGATE_CON(20), 12, GFLAGS),
 	GATE(CLK_VOP_PWM, "clk_vop_pwm", "xin24m", 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/rockchip/clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/rockchip/clk.c
@@ -180,6 +180,7 @@
 		unsigned long rate, unsigned long *parent_rate,
 		unsigned long *m, unsigned long *n)
 {
+	struct clk_fractional_divider *fd = to_clk_fd(hw);
 	unsigned long p_rate, p_parent_rate;
 	struct clk_hw *p_parent;
 
@@ -190,6 +191,8 @@
 		*parent_rate = p_parent_rate;
 	}
 
+	fd->flags |= CLK_FRAC_DIVIDER_POWER_OF_TWO_PS;
+
 	clk_fractional_divider_general_approximation(hw, rate, parent_rate, m, n);
 }
 
@@ -431,12 +434,13 @@
 				    struct rockchip_clk_branch *list,
 				    unsigned int nr_clk)
 {
-	struct clk *clk = NULL;
+	struct clk *clk;
 	unsigned int idx;
 	unsigned long flags;
 
 	for (idx = 0; idx < nr_clk; idx++, list++) {
 		flags = list->flags;
+		clk = NULL;
 
 		/* catch simple muxes */
 		switch (list->branch_type) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/samsung/clk-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/samsung/clk-pll.c
@@ -1385,6 +1385,7 @@
 	if (ret) {
 		pr_err("%s: failed to register pll clock %s : %d\n",
 			__func__, pll_clk->name, ret);
+		kfree(pll->rate_table);
 		kfree(pll);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/samsung/clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/samsung/clk.c
@@ -64,11 +64,11 @@
 	if (!ctx)
 		panic("could not allocate clock provider context.\n");
 
+	ctx->clk_data.num = nr_clks;
 	for (i = 0; i < nr_clks; ++i)
 		ctx->clk_data.hws[i] = ERR_PTR(-ENOENT);
 
 	ctx->reg_base = base;
-	ctx->clk_data.num = nr_clks;
 	spin_lock_init(&ctx->lock);
 
 	return ctx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/si5324.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/si5324.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Si5324 clock generator platform data
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_SI5324_H__
+#define __LINUX_PLATFORM_DATA_SI5324_H__
+
+/**
+ * enum si5324_pll_src - Si5324 pll clock source
+ *
+ * @SI5324_PLL_SRC_DEFAULT:	Default, do not change eeprom config
+ * @SI5324_PLL_SRC_XTAL:	Pll source clock is XTAL input
+ * @SI5324_PLL_SRC_CLKIN1:	Pll source clock is CLKIN1 input
+ * @SI5324_PLL_SRC_CLKIN2:	Pll source clock is CLKIN2 input
+ *
+ * Defines enums for clock sources.
+ */
+enum si5324_pll_src {
+	SI5324_PLL_SRC_XTAL = 0,
+	SI5324_PLL_SRC_CLKIN1 = 1,
+	SI5324_PLL_SRC_CLKIN2 = 2,
+};
+
+/**
+ * enum si5324_drive_strength - Si5324 clock output drive strength
+ *
+ * @SI5324_DRIVE_DEFAULT:	Default, do not change eeprom config
+ * @SI5324_DRIVE_2MA:		2mA clock output drive strength
+ * @SI5324_DRIVE_4MA:		4mA clock output drive strength
+ * @SI5324_DRIVE_6MA:		6mA clock output drive strength
+ * @SI5324_DRIVE_8MA:		8mA clock output drive strength
+ *
+ * Defines enums for drive strength
+ */
+enum si5324_drive_strength {
+	SI5324_DRIVE_DEFAULT = 0,
+	SI5324_DRIVE_2MA = 2,
+	SI5324_DRIVE_4MA = 4,
+	SI5324_DRIVE_6MA = 6,
+	SI5324_DRIVE_8MA = 8,
+};
+
+/**
+ * struct si5324_clkout_config - Si5324 clock output configuration
+ *
+ * @drive:	output drive strength
+ * @rate:	clkout rate
+ */
+struct si5324_clkout_config {
+	enum si5324_drive_strength drive;
+	unsigned long rate;
+};
+
+/**
+ * struct si5324_platform_data - Platform data for the Si5324 clock driver
+ *
+ * @pll_src:	Pll source clock setting
+ * @clkout:	Array of clkout configuration
+ */
+struct si5324_platform_data {
+	enum si5324_pll_src pll_src;
+	struct si5324_clkout_config clkout[2];
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/si5324drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/si5324drv.c
@@ -0,0 +1,383 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Si5324 clock driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author:	Venkateshwar Rao G <vgannava.xilinx.com>
+ *		Leon Woestenberg <leon@sidebranch.com>
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include "si5324drv.h"
+
+/**
+ * si5324_rate_approx - Find closest rational approximation N2_LS/N3 fraction.
+ *
+ * @f:		Holds the N2_LS/N3 fraction in 36.28 fixed point notation.
+ * @md:		Holds the maximum denominator (N3) value allowed.
+ * @num:	Store the numinator (N2_LS) found.
+ * @denom:	Store the denominator (N3) found.
+ *
+ * This function finds the closest rational approximation.
+ * It allows only n/1 solution and as a part of the calculation
+ * multiply fraction until no digits after the decimal point and
+ * continued fraction and check denominator at each step.
+ */
+void si5324_rate_approx(u64 f, u64 md, u32 *num, u32 *denom)
+{
+	u64 a, h[3] = { 0, 1, 0 }, k[3] = { 1, 0, 0 };
+	u64 x, d, m, n = 1;
+	int i = 0;
+
+	if (md <= 1) {
+		*denom = 1;
+		*num = (u32)(f >> 28);
+		return;
+	}
+
+	n <<= 28;
+	for (i = 0; i < 28; i++) {
+		if ((f & 0x1) == 0) {
+			n >>= 1;
+			f >>= 1;
+		} else {
+			break;
+		}
+	}
+	d = f;
+
+	for (i = 0; i < 64; i++) {
+		a = n ? (div64_u64(d, n)) : 0;
+		if (i && !a)
+			break;
+		x = d;
+		d = n;
+		div64_u64_rem(x, n, &m);
+		n = m;
+		x = a;
+		if (k[1] * a + k[0] >= md) {
+			x = div64_u64((md - k[0]), k[1]);
+			if (x * 2 >= a || k[1] >= md)
+				i = 65;
+			else
+				break;
+		}
+		h[2] = x * h[1] + h[0];
+		h[0] = h[1];
+		h[1] = h[2];
+		k[2] = x * k[1] + k[0];
+		k[0] = k[1];
+		k[1] = k[2];
+	}
+
+	*denom = (u32)k[1];
+	*num = (u32)h[1];
+}
+
+/**
+ * si5324_find_n2ls - Search through the possible settings for the N2_LS.
+ *
+ * @settings:	Holds the settings up till now.
+ *
+ * This function finds the best setting for N2_LS and N3n with the values
+ * for N1_HS, NCn_LS, and N2_HS.
+ *
+ * Return:	1 when the best possible result has been found, 0 on failure.
+ */
+static int si5324_find_n2ls(struct si5324_settingst *settings)
+{
+	u32 result = 0;
+	u64 f3_actual;
+	u64 fosc_actual;
+	u64 fout_actual;
+	u64 delta_fout;
+	u64 n2_ls_div_n3, mult_res;
+	u32 mult;
+
+	n2_ls_div_n3 = div64_u64(div64_u64(div64_u64(settings->fosc,
+			(settings->fin >> SI5324_FIN_FOUT_SHIFT)),
+			(u64)settings->n2_hs), (u64)2);
+
+	si5324_rate_approx(n2_ls_div_n3, settings->n31_max, &settings->n2_ls,
+				&settings->n31);
+	settings->n2_ls *= 2;
+
+	if (settings->n2_ls < settings->n2_ls_min) {
+		mult = div64_u64(settings->n2_ls_min, settings->n2_ls);
+		div64_u64_rem(settings->n2_ls_min, settings->n2_ls, &mult_res);
+		mult = mult_res ? mult + 1 : mult;
+		settings->n2_ls *= mult;
+		settings->n31 *= mult;
+	}
+
+	if (settings->n31 < settings->n31_min) {
+		mult = div64_u64(settings->n31_min, settings->n31);
+		div64_u64_rem(settings->n31_min, settings->n31, &mult_res);
+		mult = mult_res ? mult + 1 : mult;
+		settings->n2_ls *= mult;
+		settings->n31 *= mult;
+	}
+	pr_debug("Trying N2_LS = %d N3 = %d.\n", settings->n2_ls,
+		 settings->n31);
+
+	if (settings->n2_ls < settings->n2_ls_min ||
+	    settings->n2_ls > settings->n2_ls_max) {
+		pr_info("N2_LS out of range.\n");
+	} else if ((settings->n31 < settings->n31_min) ||
+		   (settings->n31 > settings->n31_max)) {
+		pr_info("N3 out of range.\n");
+	} else {
+		f3_actual = div64_u64(settings->fin, settings->n31);
+		fosc_actual = f3_actual * settings->n2_hs * settings->n2_ls;
+		fout_actual = div64_u64(fosc_actual,
+					(settings->n1_hs * settings->nc1_ls));
+		delta_fout = fout_actual - settings->fout;
+
+		if ((f3_actual < ((u64)SI5324_F3_MIN) <<
+			SI5324_FIN_FOUT_SHIFT) ||
+			(f3_actual > ((u64)SI5324_F3_MAX) <<
+			SI5324_FIN_FOUT_SHIFT)) {
+			pr_debug("F3 frequency out of range.\n");
+		} else if ((fosc_actual < ((u64)SI5324_FOSC_MIN) <<
+				SI5324_FIN_FOUT_SHIFT) ||
+				(fosc_actual > ((u64)SI5324_FOSC_MAX) <<
+				SI5324_FIN_FOUT_SHIFT)) {
+			pr_debug("Fosc frequency out of range.\n");
+		} else if ((fout_actual < ((u64)SI5324_FOUT_MIN) <<
+				SI5324_FIN_FOUT_SHIFT) ||
+				(fout_actual > ((u64)SI5324_FOUT_MAX) <<
+				SI5324_FIN_FOUT_SHIFT)) {
+			pr_debug("Fout frequency out of range.\n");
+		} else {
+			u64 divident = fosc_actual >> SI5324_FIN_FOUT_SHIFT;
+
+			pr_debug("Found solution: fout = %dHz delta = %dHz.\n",
+				 (u32)(fout_actual >> SI5324_FIN_FOUT_SHIFT),
+				 (u32)(delta_fout >> SI5324_FIN_FOUT_SHIFT));
+			pr_debug("fosc = %dkHz f3 = %dHz.\n",
+				 (u32)(do_div(divident, 1000)),
+				 (u32)(f3_actual >> SI5324_FIN_FOUT_SHIFT));
+
+			if (((u64)abs(delta_fout)) <
+				settings->best_delta_fout) {
+				settings->best_n1_hs = settings->n1_hs;
+				settings->best_nc1_ls = settings->nc1_ls;
+				settings->best_n2_hs = settings->n2_hs;
+				settings->best_n2_ls = settings->n2_ls;
+				settings->best_n3 = settings->n31;
+				settings->best_fout = fout_actual;
+				settings->best_delta_fout = abs(delta_fout);
+				if (delta_fout == 0)
+					result = 1;
+			}
+		}
+	}
+	return result;
+}
+
+/**
+ * si5324_find_n2 - Find a valid setting for N2_HS and N2_LS.
+ *
+ * @settings:	Holds the settings up till now.
+ *
+ * This function finds a valid settings for N2_HS and N2_LS. Iterates over
+ * all possibilities of N2_HS and then performs a binary search over the
+ * N2_LS values.
+ *
+ * Return:	1 when the best possible result has been found.
+ */
+static int si5324_find_n2(struct si5324_settingst *settings)
+{
+	u32 result = 0;
+
+	for (settings->n2_hs = SI5324_N2_HS_MAX; settings->n2_hs >=
+		SI5324_N2_HS_MIN; settings->n2_hs--) {
+		pr_debug("Trying N2_HS = %d.\n", settings->n2_hs);
+		settings->n2_ls_min = (u32)(div64_u64(settings->fosc,
+					((u64)(SI5324_F3_MAX * settings->n2_hs)
+						<< SI5324_FIN_FOUT_SHIFT)));
+
+		if (settings->n2_ls_min < SI5324_N2_LS_MIN)
+			settings->n2_ls_min = SI5324_N2_LS_MIN;
+
+		settings->n2_ls_max = (u32)(div64_u64(settings->fosc,
+					((u64)(SI5324_F3_MIN *
+					settings->n2_hs) <<
+					SI5324_FIN_FOUT_SHIFT)));
+		if (settings->n2_ls_max > SI5324_N2_LS_MAX)
+			settings->n2_ls_max = SI5324_N2_LS_MAX;
+
+		result = si5324_find_n2ls(settings);
+		if (result)
+			break;
+	}
+	return result;
+}
+
+/**
+ * si5324_calc_ncls_limits - Calculates the valid range for NCn_LS.
+ *
+ * @settings:	Holds the input and output frequencies and the setting
+ * for N1_HS.
+ *
+ * This function calculates the valid range for NCn_LS with the value
+ * for the output frequency and N1_HS already set in settings.
+ *
+ * Return:	-1 when there are no valid settings, 0 otherwise.
+ */
+int si5324_calc_ncls_limits(struct si5324_settingst *settings)
+{
+	settings->nc1_ls_min = div64_u64(settings->n1_hs_min,
+					 settings->n1_hs);
+
+	if (settings->nc1_ls_min < SI5324_NC_LS_MIN)
+		settings->nc1_ls_min = SI5324_NC_LS_MIN;
+	if (settings->nc1_ls_min > 1 &&	(settings->nc1_ls_min & 0x1) == 1)
+		settings->nc1_ls_min++;
+	settings->nc1_ls_max = div64_u64(settings->n1_hs_max, settings->n1_hs);
+
+	if (settings->nc1_ls_max > SI5324_NC_LS_MAX)
+		settings->nc1_ls_max = SI5324_NC_LS_MAX;
+
+	if ((settings->nc1_ls_max & 0x1) == 1)
+		settings->nc1_ls_max--;
+	if ((settings->nc1_ls_max * settings->n1_hs < settings->n1_hs_min) ||
+	    (settings->nc1_ls_min * settings->n1_hs > settings->n1_hs_max))
+		return -1;
+
+	return 0;
+}
+
+/**
+ * si5324_find_ncls - Find a valid setting for NCn_LS
+ *
+ * @settings:	Holds the input and output frequencies, the setting for
+ * N1_HS, and the limits for NCn_LS.
+ *
+ * This function find a valid setting for NCn_LS that can deliver the correct
+ * output frequency. Assumes that the valid range is relatively small
+ * so a full search can be done (should be true for video clock frequencies).
+ *
+ * Return:	1 when the best possible result has been found.
+ */
+static int si5324_find_ncls(struct si5324_settingst *settings)
+{
+	u64 fosc_1;
+	u32 result;
+
+	fosc_1 = settings->fout * settings->n1_hs;
+	for (settings->nc1_ls = settings->nc1_ls_min;
+		settings->nc1_ls <= settings->nc1_ls_max;) {
+		settings->fosc = fosc_1 * settings->nc1_ls;
+		pr_debug("Trying NCn_LS = %d: fosc = %dkHz.\n",
+			 settings->nc1_ls,
+			 (u32)(div64_u64((settings->fosc >>
+				SI5324_FIN_FOUT_SHIFT), 1000)));
+
+		result = si5324_find_n2(settings);
+		if (result)
+			break;
+		if (settings->nc1_ls == 1)
+			settings->nc1_ls++;
+		else
+			settings->nc1_ls += 2;
+	}
+	return result;
+}
+
+/**
+ * si5324_calcfreqsettings - Calculate the frequency settings
+ *
+ * @clkinfreq:	Frequency of the input clock.
+ * @clkoutfreq:	Desired output clock frequency.
+ * @clkactual:	Actual clock frequency.
+ * @n1_hs:	Set to the value for the N1_HS register.
+ * @ncn_ls:	Set to the value for the NCn_LS register.
+ * @n2_hs:	Set to the value for the N2_HS register.
+ * @n2_ls:	Set to the value for the N2_LS register.
+ * @n3n:	Set to the value for the N3n register.
+ * @bwsel:	Set to the value for the BW_SEL register.
+ *
+ * This funciton calculates the frequency settings for the desired output
+ * frequency.
+ *
+ * Return:	SI5324_SUCCESS for success, SI5324_ERR_FREQ when the
+ * requested frequency cannot be generated.
+ */
+int si5324_calcfreqsettings(u32 clkinfreq, u32 clkoutfreq, u32 *clkactual,
+			    u8 *n1_hs, u32 *ncn_ls, u8 *n2_hs, u32 *n2_ls,
+			    u32 *n3n, u8 *bwsel)
+{
+	struct si5324_settingst settings;
+	int result;
+
+	settings.fin = (u64)clkinfreq << SI5324_FIN_FOUT_SHIFT;
+	settings.fout = (u64)clkoutfreq << SI5324_FIN_FOUT_SHIFT;
+	settings.best_delta_fout = settings.fout;
+
+	settings.n1_hs_min = (int)(div64_u64(SI5324_FOSC_MIN, clkoutfreq));
+	if (settings.n1_hs_min < SI5324_N1_HS_MIN * SI5324_NC_LS_MIN)
+		settings.n1_hs_min = SI5324_N1_HS_MIN * SI5324_NC_LS_MIN;
+
+	settings.n1_hs_max = (int)(div64_u64(SI5324_FOSC_MAX, clkoutfreq));
+	if (settings.n1_hs_max > SI5324_N1_HS_MAX * SI5324_NC_LS_MAX)
+		settings.n1_hs_max = SI5324_N1_HS_MAX * SI5324_NC_LS_MAX;
+
+	settings.n31_min = div64_u64(clkinfreq, SI5324_F3_MAX);
+	if (settings.n31_min < SI5324_N3_MIN)
+		settings.n31_min = SI5324_N3_MIN;
+
+	settings.n31_max = div64_u64(clkinfreq, SI5324_F3_MIN);
+	if (settings.n31_max > SI5324_N3_MAX)
+		settings.n31_max = SI5324_N3_MAX;
+
+	/* Find a valid oscillator frequency with the highest setting of N1_HS
+	 * possible (reduces power)
+	 */
+	for (settings.n1_hs = SI5324_N1_HS_MAX;
+		settings.n1_hs >= SI5324_N1_HS_MIN; settings.n1_hs--) {
+		pr_debug("Trying N1_HS = %d.\n", settings.n1_hs);
+
+		result = si5324_calc_ncls_limits(&settings);
+		if (result) {
+			pr_debug("No valid settings\n");
+			continue;
+		}
+		result = si5324_find_ncls(&settings);
+		if (result)
+			break;
+	}
+
+		pr_debug("Si5324: settings.best_delta_fout = %llu\n",
+			 (unsigned long long)settings.best_delta_fout);
+		pr_debug("Si5324: settings.fout = %llu\n",
+			 (unsigned long long)settings.fout);
+
+	if (settings.best_delta_fout == settings.fout) {
+		pr_debug("Si5324: No valid settings found.");
+		return SI5324_ERR_FREQ;
+	}
+		pr_debug("Si5324: Found solution: fout = %dHz.\n",
+			 (u32)(settings.best_fout >> 28));
+
+	/* Post processing: convert temporary values to actual registers */
+	*n1_hs = (u8)settings.best_n1_hs - 4;
+	*ncn_ls = settings.best_nc1_ls - 1;
+	*n2_hs = (u8)settings.best_n2_hs - 4;
+	*n2_ls = settings.best_n2_ls - 1;
+	*n3n = settings.best_n3 - 1;
+	/*
+	 * How must the bandwidth selection be determined?
+	 * Not all settings will be valid.
+	 * refclk 2, 0xA2, BWSEL_REG=1010 (?)
+	 * free running 2, 0x42, BWSEL_REG=0100 (?)
+	 */
+	*bwsel = 6;
+
+	if (clkactual)
+		*clkactual = (settings.best_fout >> SI5324_FIN_FOUT_SHIFT);
+
+	return SI5324_SUCCESS;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/si5324drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/si5324drv.h
@@ -0,0 +1,100 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Si5324 clock driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ */
+
+#ifndef SI5324DRV_H_
+#define SI5324DRV_H_
+
+#include <linux/types.h>
+
+/******************************************************************************
+ * User settable defines that depend on the specific board design.
+ * The defaults are for the Xilinx KC705 board.
+ *****************************************************************************/
+
+#define SI5324_XTAL_FREQ 114285000UL
+
+/******************************************************************************
+ * Defines independent on the specific board design. Should not be changed.
+ *****************************************************************************/
+
+#define SI5324_SUCCESS		0 /*< Operation was successful */
+#define SI5324_ERR_IIC		-1 /*< IIC error occurred */
+#define SI5324_ERR_FREQ		-2 /*< Could not calculate frequency setting */
+#define SI5324_ERR_PARM		-3 /*< Invalid parameter */
+
+#define SI5324_CLKSRC_CLK1	1 /*< Use clock input 1 */
+#define SI5324_CLKSRC_CLK2	2 /*< Use clock input 2 */
+#define SI5324_CLKSRC_XTAL	3 /*< Use crystal (free running mode) */
+
+#define SI5324_FOSC_MIN		4850000000UL /*< Min oscillator frequency */
+#define SI5324_FOSC_MAX		5670000000UL /*< Max oscillator frequency */
+#define SI5324_F3_MIN		10000 /*< Min phase detector frequency */
+#define SI5324_F3_MAX		2000000 /*< Max phase detector frequency */
+#define SI5324_FIN_MIN		2000 /*< Min input frequency */
+#define SI5324_FIN_MAX		710000000UL /*< Max input frequency */
+#define SI5324_FOUT_MIN		2000 /*< Min output frequency */
+#define SI5324_FOUT_MAX		945000000UL /*< Max output frequency */
+
+#define SI5324_N1_HS_MIN	6
+#define SI5324_N1_HS_MAX	11
+#define SI5324_NC_LS_MIN	1
+#define SI5324_NC_LS_MAX	0x100000
+#define SI5324_N2_HS_MIN	4
+#define SI5324_N2_HS_MAX	11
+#define SI5324_N2_LS_MIN	2 /* even values only */
+#define SI5324_N2_LS_MAX	0x100000
+#define SI5324_N3_MIN		1
+#define SI5324_N3_MAX		0x080000
+#define SI5324_FIN_FOUT_SHIFT	28
+
+struct si5324_settingst {
+	/* high-speed output divider */
+	u32 n1_hs_min;
+	u32 n1_hs_max;
+	u32 n1_hs;
+
+	/* low-speed output divider for clkout1 */
+	u32 nc1_ls_min;
+	u32 nc1_ls_max;
+	u32 nc1_ls;
+
+	/* low-speed output divider for clkout2 */
+	u32 nc2_ls_min;
+	u32 nc2_ls_max;
+	u32 nc2_ls;
+
+	/* high-speed feedback divider (PLL multiplier) */
+	u32 n2_hs;
+	/* low-speed feedback divider (PLL multiplier) */
+	u32 n2_ls_min;
+	u32 n2_ls_max;
+	u32 n2_ls;
+
+	/* input divider for clk1 */
+	u32 n31_min;
+	u32 n31_max;
+	u32 n31;
+
+	u64 fin;
+	u64 fout;
+	u64 fosc;
+	u64 best_delta_fout;
+	u64 best_fout;
+	u32 best_n1_hs;
+	u32 best_nc1_ls;
+	u32 best_n2_hs;
+	u32 best_n2_ls;
+	u32 best_n3;
+};
+
+int si5324_calcfreqsettings(u32 clkinfreq, u32 clkoutfreq, u32 *clkactual,
+			    u8 *n1_hs, u32 *ncn_ls, u8 *n2_hs,
+			    u32 *n2_ls, u32 *n3n, u8 *bwsel);
+void si5324_rate_approx(u64 f, u64 md, u32 *num, u32 *denom);
+int si5324_calc_ncls_limits(struct si5324_settingst *settings);
+
+#endif /* SI5324DRV_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sifive/sifive-prci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sifive/sifive-prci.c
@@ -4,7 +4,6 @@
  * Copyright (C) 2020 Zong Li
  */
 
-#include <linux/clkdev.h>
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/of_device.h>
@@ -541,13 +540,6 @@
 			return r;
 		}
 
-		r = clk_hw_register_clkdev(&pic->hw, pic->name, dev_name(dev));
-		if (r) {
-			dev_warn(dev, "Failed to register clkdev for %s: %d\n",
-				 init.name, r);
-			return r;
-		}
-
 		pd->hw_clks.hws[i] = &pic->hw;
 	}
 
@@ -602,6 +594,7 @@
 		return r;
 	}
 	r = __prci_register_clocks(dev, pd, desc);
+
 	if (r) {
 		dev_err(dev, "could not register clocks: %d\n", r);
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/socfpga/clk-gate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/socfpga/clk-gate.c
@@ -188,8 +188,10 @@
 		return;
 
 	ops = kmemdup(&gateclk_ops, sizeof(gateclk_ops), GFP_KERNEL);
-	if (WARN_ON(!ops))
+	if (WARN_ON(!ops)) {
+		kfree(socfpga_clk);
 		return;
+	}
 
 	rc = of_property_read_u32_array(node, "clk-gate", clk_gate, 2);
 	if (rc)
@@ -243,6 +245,7 @@
 
 	err = clk_hw_register(NULL, hw_clk);
 	if (err) {
+		kfree(ops);
 		kfree(socfpga_clk);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/socfpga/stratix10-clk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/socfpga/stratix10-clk.h
@@ -7,8 +7,10 @@
 #define	__STRATIX10_CLK_H
 
 struct stratix10_clock_data {
-	struct clk_hw_onecell_data	clk_data;
 	void __iomem		*base;
+
+	/* Must be last */
+	struct clk_hw_onecell_data	clk_data;
 };
 
 struct stratix10_pll_clock {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sprd/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sprd/common.c
@@ -17,7 +17,6 @@
 	.reg_bits	= 32,
 	.reg_stride	= 4,
 	.val_bits	= 32,
-	.max_register	= 0xffff,
 	.fast_io	= true,
 };
 
@@ -41,8 +40,10 @@
 {
 	void __iomem *base;
 	struct device *dev = &pdev->dev;
-	struct device_node *node = dev->of_node;
+	struct device_node *node = dev->of_node, *np;
 	struct regmap *regmap;
+	struct resource *res;
+	struct regmap_config reg_config = sprdclk_regmap_config;
 
 	if (of_find_property(node, "sprd,syscon", NULL)) {
 		regmap = syscon_regmap_lookup_by_phandle(node, "sprd,syscon");
@@ -50,20 +51,23 @@
 			pr_err("%s: failed to get syscon regmap\n", __func__);
 			return PTR_ERR(regmap);
 		}
-	} else if (of_device_is_compatible(of_get_parent(dev->of_node),
-			   "syscon")) {
-		regmap = device_node_to_regmap(of_get_parent(dev->of_node));
+	} else if (of_device_is_compatible(np =	of_get_parent(node), "syscon") ||
+		   (of_node_put(np), 0)) {
+		regmap = device_node_to_regmap(np);
+		of_node_put(np);
 		if (IS_ERR(regmap)) {
 			dev_err(dev, "failed to get regmap from its parent.\n");
 			return PTR_ERR(regmap);
 		}
 	} else {
-		base = devm_platform_ioremap_resource(pdev, 0);
+		base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 		if (IS_ERR(base))
 			return PTR_ERR(base);
 
+		reg_config.max_register = resource_size(res) - reg_config.reg_stride;
+
 		regmap = devm_regmap_init_mmio(&pdev->dev, base,
-					       &sprdclk_regmap_config);
+					       &reg_config);
 		if (IS_ERR(regmap)) {
 			pr_err("failed to init regmap\n");
 			return PTR_ERR(regmap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/st/clkgen-fsyn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/st/clkgen-fsyn.c
@@ -1008,9 +1008,10 @@
 
 	clk = st_clk_register_quadfs_pll(pll_name, clk_parent_name, datac->data,
 			reg, lock);
-	if (IS_ERR(clk))
+	if (IS_ERR(clk)) {
+		kfree(lock);
 		goto err_exit;
-	else
+	} else
 		pr_debug("%s: parent %s rate %u\n",
 			__clk_get_name(clk),
 			__clk_get_name(clk_get_parent(clk)),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun4i-a10.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun4i-a10.c
@@ -1464,7 +1464,7 @@
 	val &= ~GENMASK(7, 6);
 	writel(val | (2 << 6), reg + SUN4I_AHB_REG);
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun4i_a10_ccu_setup(struct device_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
@@ -196,7 +196,7 @@
 	if (IS_ERR(reg))
 		return PTR_ERR(reg);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_a100_r_ccu_desc);
 }
 
 static const struct of_device_id sun50i_a100_r_ccu_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
@@ -437,7 +437,7 @@
 					  24, 2,	/* mux */
 					  BIT(31),	/* gate */
 					  2,		/* post-div */
-					  CLK_SET_RATE_NO_REPARENT);
+					  0);
 
 static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
 					  0, 4,		/* M */
@@ -445,7 +445,7 @@
 					  24, 2,	/* mux */
 					  BIT(31),	/* gate */
 					  2,		/* post-div */
-					  CLK_SET_RATE_NO_REPARENT);
+					  0);
 
 static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
 					  0, 4,		/* M */
@@ -453,7 +453,7 @@
 					  24, 2,	/* mux */
 					  BIT(31),	/* gate */
 					  2,		/* post-div */
-					  CLK_SET_RATE_NO_REPARENT);
+					  0);
 
 static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
 static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
@@ -1247,7 +1247,7 @@
 		writel(val, reg + sun50i_a100_usb2_clk_regs[i]);
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_a100_ccu_desc);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun50i-a64.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun50i-a64.c
@@ -955,7 +955,7 @@
 
 	writel(0x515, reg + SUN50I_A64_PLL_MIPI_REG);
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a64_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_a64_ccu_desc);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -232,7 +232,7 @@
 		return;
 	}
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun50i_h6_r_ccu_setup(struct device_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
@@ -1181,12 +1181,19 @@
 	SUN50I_H6_USB3_CLK_REG,
 };
 
+static struct ccu_mux_nb sun50i_h6_cpu_nb = {
+	.common		= &cpux_clk.common,
+	.cm		= &cpux_clk.mux,
+	.delay_us       = 1,
+	.bypass_index   = 0, /* index of 24 MHz oscillator */
+};
+
 static int sun50i_h6_ccu_probe(struct platform_device *pdev)
 {
 	struct resource *res;
 	void __iomem *reg;
+	int i, ret;
 	u32 val;
-	int i;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	reg = devm_ioremap_resource(&pdev->dev, res);
@@ -1240,7 +1247,15 @@
 	val |= BIT(24);
 	writel(val, reg + SUN50I_H6_HDMI_CEC_CLK_REG);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_h6_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_h6_ccu_desc);
+	if (ret)
+		return ret;
+
+	/* Reparent CPU during PLL CPUX rate changes */
+	ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
+				  &sun50i_h6_cpu_nb);
+
+	return 0;
 }
 
 static const struct of_device_id sun50i_h6_ccu_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
@@ -1141,9 +1141,7 @@
 	val |= BIT(24);
 	writel(val, reg + SUN50I_H616_HDMI_CEC_CLK_REG);
 
-	i = sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
-	if (i)
-		pr_err("%pOF: probing clocks fails: %d\n", node, i);
+	of_sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
 }
 
 CLK_OF_DECLARE(sun50i_h616_ccu, "allwinner,sun50i-h616-ccu",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun5i.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun5i.c
@@ -1012,7 +1012,7 @@
 	val &= ~GENMASK(7, 6);
 	writel(val | (2 << 6), reg + SUN5I_AHB_REG);
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun5i_a10s_ccu_setup(struct device_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun6i-a31.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun6i-a31.c
@@ -1257,7 +1257,7 @@
 	val |= 0x3 << 12;
 	writel(val, reg + SUN6I_A31_AHB1_REG);
 
-	sunxi_ccu_probe(node, reg, &sun6i_a31_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &sun6i_a31_ccu_desc);
 
 	ccu_mux_notifier_register(pll_cpu_clk.common.hw.clk,
 				  &sun6i_a31_cpu_nb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-a23.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-a23.c
@@ -745,7 +745,7 @@
 	val &= ~BIT(16);
 	writel(val, reg + SUN8I_A23_PLL_MIPI_REG);
 
-	sunxi_ccu_probe(node, reg, &sun8i_a23_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &sun8i_a23_ccu_desc);
 }
 CLK_OF_DECLARE(sun8i_a23_ccu, "allwinner,sun8i-a23-ccu",
 	       sun8i_a23_ccu_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
@@ -805,7 +805,7 @@
 	val &= ~BIT(16);
 	writel(val, reg + SUN8I_A33_PLL_MIPI_REG);
 
-	sunxi_ccu_probe(node, reg, &sun8i_a33_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &sun8i_a33_ccu_desc);
 
 	/* Gate then ungate PLL CPU after any rate changes */
 	ccu_pll_notifier_register(&sun8i_a33_pll_cpu_nb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-a83t.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-a83t.c
@@ -906,7 +906,7 @@
 	sun8i_a83t_cpu_pll_fixup(reg + SUN8I_A83T_PLL_C0CPUX_REG);
 	sun8i_a83t_cpu_pll_fixup(reg + SUN8I_A83T_PLL_C1CPUX_REG);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun8i_a83t_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun8i_a83t_ccu_desc);
 }
 
 static const struct of_device_id sun8i_a83t_ccu_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-de2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-de2.c
@@ -342,7 +342,7 @@
 		goto err_disable_mod_clk;
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, ccu_desc);
 	if (ret)
 		goto err_assert_reset;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
@@ -1154,7 +1154,7 @@
 	val &= ~GENMASK(19, 16);
 	writel(val | (0 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 
 	/* Gate then ungate PLL CPU after any rate changes */
 	ccu_pll_notifier_register(&sun8i_h3_pll_cpu_nb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-r.c
@@ -265,7 +265,7 @@
 		return;
 	}
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun8i_a83t_r_ccu_setup(struct device_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
@@ -1346,7 +1346,7 @@
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun8i_r40_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun8i_r40_ccu_desc);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
@@ -822,7 +822,7 @@
 	val &= ~GENMASK(19, 16);
 	writel(val, reg + SUN8I_V3S_PLL_AUDIO_REG);
 
-	sunxi_ccu_probe(node, reg, ccu_desc);
+	of_sunxi_ccu_probe(node, reg, ccu_desc);
 }
 
 static void __init sun8i_v3s_ccu_setup(struct device_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c
@@ -246,8 +246,7 @@
 		goto err_disable_clk;
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg,
-			      &sun9i_a80_de_clk_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun9i_a80_de_clk_desc);
 	if (ret)
 		goto err_assert_reset;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c
@@ -117,8 +117,7 @@
 		return ret;
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg,
-			      &sun9i_a80_usb_clk_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun9i_a80_usb_clk_desc);
 	if (ret)
 		goto err_disable_clk;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-sun9i-a80.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-sun9i-a80.c
@@ -1231,7 +1231,7 @@
 	sun9i_a80_cpu_pll_fixup(reg + SUN9I_A80_PLL_C0CPUX_REG);
 	sun9i_a80_cpu_pll_fixup(reg + SUN9I_A80_PLL_C1CPUX_REG);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun9i_a80_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun9i_a80_ccu_desc);
 }
 
 static const struct of_device_id sun9i_a80_ccu_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c
@@ -538,7 +538,7 @@
 	val &= ~GENMASK(19, 16);
 	writel(val | (3 << 16), reg + SUNIV_PLL_AUDIO_REG);
 
-	sunxi_ccu_probe(node, reg, &suniv_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &suniv_ccu_desc);
 
 	/* Gate then ungate PLL CPU after any rate changes */
 	ccu_pll_notifier_register(&suniv_pll_cpu_nb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu_common.c
@@ -7,6 +7,7 @@
 
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
+#include <linux/device.h>
 #include <linux/iopoll.h>
 #include <linux/slab.h>
 
@@ -14,6 +15,11 @@
 #include "ccu_gate.h"
 #include "ccu_reset.h"
 
+struct sunxi_ccu {
+	const struct sunxi_ccu_desc	*desc;
+	struct ccu_reset		reset;
+};
+
 static DEFINE_SPINLOCK(ccu_lock);
 
 void ccu_helper_wait_for_lock(struct ccu_common *common, u32 lock)
@@ -79,12 +85,15 @@
 				     &pll_nb->clk_nb);
 }
 
-int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
-		    const struct sunxi_ccu_desc *desc)
+static int sunxi_ccu_probe(struct sunxi_ccu *ccu, struct device *dev,
+			   struct device_node *node, void __iomem *reg,
+			   const struct sunxi_ccu_desc *desc)
 {
 	struct ccu_reset *reset;
 	int i, ret;
 
+	ccu->desc = desc;
+
 	for (i = 0; i < desc->num_ccu_clks; i++) {
 		struct ccu_common *cclk = desc->ccu_clks[i];
 
@@ -103,7 +112,10 @@
 			continue;
 
 		name = hw->init->name;
-		ret = of_clk_hw_register(node, hw);
+		if (dev)
+			ret = clk_hw_register(dev, hw);
+		else
+			ret = of_clk_hw_register(node, hw);
 		if (ret) {
 			pr_err("Couldn't register clock %d - %s\n", i, name);
 			goto err_clk_unreg;
@@ -115,15 +127,10 @@
 	if (ret)
 		goto err_clk_unreg;
 
-	reset = kzalloc(sizeof(*reset), GFP_KERNEL);
-	if (!reset) {
-		ret = -ENOMEM;
-		goto err_alloc_reset;
-	}
-
+	reset = &ccu->reset;
 	reset->rcdev.of_node = node;
 	reset->rcdev.ops = &ccu_reset_ops;
-	reset->rcdev.owner = THIS_MODULE;
+	reset->rcdev.owner = dev ? dev->driver->owner : THIS_MODULE;
 	reset->rcdev.nr_resets = desc->num_resets;
 	reset->base = reg;
 	reset->lock = &ccu_lock;
@@ -131,13 +138,11 @@
 
 	ret = reset_controller_register(&reset->rcdev);
 	if (ret)
-		goto err_of_clk_unreg;
+		goto err_del_provider;
 
 	return 0;
 
-err_of_clk_unreg:
-	kfree(reset);
-err_alloc_reset:
+err_del_provider:
 	of_clk_del_provider(node);
 err_clk_unreg:
 	while (--i >= 0) {
@@ -149,3 +154,59 @@
 	}
 	return ret;
 }
+
+static void devm_sunxi_ccu_release(struct device *dev, void *res)
+{
+	struct sunxi_ccu *ccu = res;
+	const struct sunxi_ccu_desc *desc = ccu->desc;
+	int i;
+
+	reset_controller_unregister(&ccu->reset.rcdev);
+	of_clk_del_provider(dev->of_node);
+
+	for (i = 0; i < desc->hw_clks->num; i++) {
+		struct clk_hw *hw = desc->hw_clks->hws[i];
+
+		if (!hw)
+			continue;
+		clk_hw_unregister(hw);
+	}
+}
+
+int devm_sunxi_ccu_probe(struct device *dev, void __iomem *reg,
+			 const struct sunxi_ccu_desc *desc)
+{
+	struct sunxi_ccu *ccu;
+	int ret;
+
+	ccu = devres_alloc(devm_sunxi_ccu_release, sizeof(*ccu), GFP_KERNEL);
+	if (!ccu)
+		return -ENOMEM;
+
+	ret = sunxi_ccu_probe(ccu, dev, dev->of_node, reg, desc);
+	if (ret) {
+		devres_free(ccu);
+		return ret;
+	}
+
+	devres_add(dev, ccu);
+
+	return 0;
+}
+
+void of_sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
+			const struct sunxi_ccu_desc *desc)
+{
+	struct sunxi_ccu *ccu;
+	int ret;
+
+	ccu = kzalloc(sizeof(*ccu), GFP_KERNEL);
+	if (!ccu)
+		return;
+
+	ret = sunxi_ccu_probe(ccu, NULL, node, reg, desc);
+	if (ret) {
+		pr_err("%pOF: probing clocks failed: %d\n", node, ret);
+		kfree(ccu);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu_common.h
@@ -63,7 +63,9 @@
 
 int ccu_pll_notifier_register(struct ccu_pll_nb *pll_nb);
 
-int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
-		    const struct sunxi_ccu_desc *desc);
+int devm_sunxi_ccu_probe(struct device *dev, void __iomem *reg,
+			 const struct sunxi_ccu_desc *desc);
+void of_sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
+			const struct sunxi_ccu_desc *desc);
 
 #endif /* _COMMON_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi-ng/ccu_mmc_timing.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi-ng/ccu_mmc_timing.c
@@ -43,7 +43,7 @@
 EXPORT_SYMBOL_GPL(sunxi_ccu_set_mmc_timing_mode);
 
 /**
- * sunxi_ccu_set_mmc_timing_mode: Get the current MMC clock timing mode
+ * sunxi_ccu_get_mmc_timing_mode: Get the current MMC clock timing mode
  * @clk: clock to query
  *
  * Returns 0 if the clock is in old timing mode, > 0 if it is in
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/sunxi/clk-sun9i-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/sunxi/clk-sun9i-mmc.c
@@ -109,6 +109,8 @@
 	spin_lock_init(&data->lock);
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r)
+		return -EINVAL;
 	/* one clock/reset pair per word */
 	count = DIV_ROUND_UP((resource_size(r)), SUN9I_MMC_WIDTH);
 	data->membase = devm_ioremap_resource(&pdev->dev, r);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/tegra/clk-bpmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/tegra/clk-bpmp.c
@@ -159,7 +159,7 @@
 
 	err = tegra_bpmp_clk_transfer(clk->bpmp, &msg);
 	if (err < 0)
-		return err;
+		return 0;
 
 	return response.rate;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/tegra/clk-dfll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/tegra/clk-dfll.c
@@ -271,6 +271,7 @@
 	struct clk			*ref_clk;
 	struct clk			*i2c_clk;
 	struct clk			*dfll_clk;
+	struct reset_control		*dfll_rst;
 	struct reset_control		*dvco_rst;
 	unsigned long			ref_rate;
 	unsigned long			i2c_clk_rate;
@@ -1464,6 +1465,7 @@
 		return -EINVAL;
 	}
 
+	reset_control_deassert(td->dfll_rst);
 	reset_control_deassert(td->dvco_rst);
 
 	ret = clk_prepare(td->ref_clk);
@@ -1509,6 +1511,7 @@
 	clk_unprepare(td->ref_clk);
 
 	reset_control_assert(td->dvco_rst);
+	reset_control_assert(td->dfll_rst);
 
 	return ret;
 }
@@ -1530,6 +1533,7 @@
 	}
 
 	reset_control_assert(td->dvco_rst);
+	reset_control_assert(td->dfll_rst);
 
 	return 0;
 }
@@ -1548,6 +1552,7 @@
 {
 	struct tegra_dfll *td = dev_get_drvdata(dev);
 
+	reset_control_deassert(td->dfll_rst);
 	reset_control_deassert(td->dvco_rst);
 
 	pm_runtime_get_sync(td->dev);
@@ -1951,6 +1956,12 @@
 
 	td->soc = soc;
 
+	td->dfll_rst = devm_reset_control_get_optional(td->dev, "dfll");
+	if (IS_ERR(td->dfll_rst)) {
+		dev_err(td->dev, "couldn't get dfll reset\n");
+		return PTR_ERR(td->dfll_rst);
+	}
+
 	td->dvco_rst = devm_reset_control_get(td->dev, "dvco");
 	if (IS_ERR(td->dvco_rst)) {
 		dev_err(td->dev, "couldn't get dvco reset\n");
@@ -2087,6 +2098,7 @@
 	clk_unprepare(td->i2c_clk);
 
 	reset_control_assert(td->dvco_rst);
+	reset_control_assert(td->dfll_rst);
 
 	return td->soc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/tegra/clk-tegra114.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/tegra/clk-tegra114.c
@@ -1317,6 +1317,7 @@
 	}
 
 	pmc_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!pmc_base) {
 		pr_err("Can't map pmc registers\n");
 		WARN_ON(1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/tegra/clk-tegra124-emc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/tegra/clk-tegra124-emc.c
@@ -198,6 +198,7 @@
 
 	tegra->emc = platform_get_drvdata(pdev);
 	if (!tegra->emc) {
+		put_device(&pdev->dev);
 		pr_err("%s: cannot find EMC driver\n", __func__);
 		return NULL;
 	}
@@ -463,6 +464,7 @@
 		err = load_one_timing_from_dt(tegra, timing, child);
 		if (err) {
 			of_node_put(child);
+			kfree(tegra->timings);
 			return err;
 		}
 
@@ -514,6 +516,7 @@
 		err = load_timings_from_dt(tegra, node, node_ram_code);
 		if (err) {
 			of_node_put(node);
+			kfree(tegra);
 			return ERR_PTR(err);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/tegra/clk-tegra20.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/tegra/clk-tegra20.c
@@ -18,24 +18,24 @@
 #define MISC_CLK_ENB 0x48
 
 #define OSC_CTRL 0x50
-#define OSC_CTRL_OSC_FREQ_MASK (3<<30)
-#define OSC_CTRL_OSC_FREQ_13MHZ (0<<30)
-#define OSC_CTRL_OSC_FREQ_19_2MHZ (1<<30)
-#define OSC_CTRL_OSC_FREQ_12MHZ (2<<30)
-#define OSC_CTRL_OSC_FREQ_26MHZ (3<<30)
-#define OSC_CTRL_MASK (0x3f2 | OSC_CTRL_OSC_FREQ_MASK)
-
-#define OSC_CTRL_PLL_REF_DIV_MASK (3<<28)
-#define OSC_CTRL_PLL_REF_DIV_1		(0<<28)
-#define OSC_CTRL_PLL_REF_DIV_2		(1<<28)
-#define OSC_CTRL_PLL_REF_DIV_4		(2<<28)
+#define OSC_CTRL_OSC_FREQ_MASK (3u<<30)
+#define OSC_CTRL_OSC_FREQ_13MHZ (0u<<30)
+#define OSC_CTRL_OSC_FREQ_19_2MHZ (1u<<30)
+#define OSC_CTRL_OSC_FREQ_12MHZ (2u<<30)
+#define OSC_CTRL_OSC_FREQ_26MHZ (3u<<30)
+#define OSC_CTRL_MASK (0x3f2u | OSC_CTRL_OSC_FREQ_MASK)
+
+#define OSC_CTRL_PLL_REF_DIV_MASK	(3u<<28)
+#define OSC_CTRL_PLL_REF_DIV_1		(0u<<28)
+#define OSC_CTRL_PLL_REF_DIV_2		(1u<<28)
+#define OSC_CTRL_PLL_REF_DIV_4		(2u<<28)
 
 #define OSC_FREQ_DET 0x58
-#define OSC_FREQ_DET_TRIG (1<<31)
+#define OSC_FREQ_DET_TRIG (1u<<31)
 
 #define OSC_FREQ_DET_STATUS 0x5c
-#define OSC_FREQ_DET_BUSY (1<<31)
-#define OSC_FREQ_DET_CNT_MASK 0xFFFF
+#define OSC_FREQ_DET_BUSYu (1<<31)
+#define OSC_FREQ_DET_CNT_MASK 0xFFFFu
 
 #define TEGRA20_CLK_PERIPH_BANKS	3
 
@@ -1128,6 +1128,7 @@
 	}
 
 	pmc_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!pmc_base) {
 		pr_err("Can't map pmc registers\n");
 		BUG();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/tegra/clk-tegra210.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/tegra/clk-tegra210.c
@@ -3748,6 +3748,7 @@
 	}
 
 	pmc_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!pmc_base) {
 		pr_err("Can't map pmc registers\n");
 		WARN_ON(1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/apll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/apll.c
@@ -139,6 +139,7 @@
 	struct clk_hw *hw = user;
 	struct clk_hw_omap *clk_hw = to_clk_hw_omap(hw);
 	struct dpll_data *ad = clk_hw->dpll_data;
+	const char *name;
 	struct clk *clk;
 	const struct clk_init_data *init = clk_hw->hw.init;
 
@@ -166,7 +167,8 @@
 
 	ad->clk_bypass = __clk_get_hw(clk);
 
-	clk = ti_clk_register_omap_hw(NULL, &clk_hw->hw, node->name);
+	name = ti_dt_clk_name(node);
+	clk = of_ti_clk_register_omap_hw(node, &clk_hw->hw, name);
 	if (!IS_ERR(clk)) {
 		of_clk_add_provider(node, of_clk_src_simple_get, clk);
 		kfree(init->parent_names);
@@ -198,7 +200,7 @@
 	clk_hw->dpll_data = ad;
 	clk_hw->hw.init = init;
 
-	init->name = node->name;
+	init->name = ti_dt_clk_name(node);
 	init->ops = &apll_ck_ops;
 
 	init->num_parents = of_clk_get_parent_count(node);
@@ -347,6 +349,7 @@
 	struct dpll_data *ad = NULL;
 	struct clk_hw_omap *clk_hw = NULL;
 	struct clk_init_data *init = NULL;
+	const char *name;
 	struct clk *clk;
 	const char *parent_name;
 	u32 val;
@@ -362,7 +365,8 @@
 	clk_hw->dpll_data = ad;
 	clk_hw->hw.init = init;
 	init->ops = &omap2_apll_ops;
-	init->name = node->name;
+	name = ti_dt_clk_name(node);
+	init->name = name;
 	clk_hw->ops = &omap2_apll_hwops;
 
 	init->num_parents = of_clk_get_parent_count(node);
@@ -403,7 +407,8 @@
 	if (ret)
 		goto cleanup;
 
-	clk = ti_clk_register_omap_hw(NULL, &clk_hw->hw, node->name);
+	name = ti_dt_clk_name(node);
+	clk = of_ti_clk_register_omap_hw(node, &clk_hw->hw, name);
 	if (!IS_ERR(clk)) {
 		of_clk_add_provider(node, of_clk_src_simple_get, clk);
 		kfree(init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/autoidle.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/autoidle.c
@@ -205,7 +205,7 @@
 		return -ENOMEM;
 
 	clk->shift = shift;
-	clk->name = node->name;
+	clk->name = ti_dt_clk_name(node);
 	ret = ti_clk_get_reg_addr(node, 0, &clk->reg);
 	if (ret) {
 		kfree(clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/clk-dra7-atl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/clk-dra7-atl.c
@@ -173,6 +173,7 @@
 	struct dra7_atl_desc *clk_hw = NULL;
 	struct clk_init_data init = { NULL };
 	const char **parent_names = NULL;
+	const char *name;
 	struct clk *clk;
 
 	clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
@@ -183,7 +184,8 @@
 
 	clk_hw->hw.init = &init;
 	clk_hw->divider = 1;
-	init.name = node->name;
+	name = ti_dt_clk_name(node);
+	init.name = name;
 	init.ops = &atl_clk_ops;
 	init.flags = CLK_IGNORE_UNUSED;
 	init.num_parents = of_clk_get_parent_count(node);
@@ -203,7 +205,7 @@
 
 	init.parent_names = parent_names;
 
-	clk = ti_clk_register(NULL, &clk_hw->hw, node->name);
+	clk = of_ti_clk_register(node, &clk_hw->hw, name);
 
 	if (!IS_ERR(clk)) {
 		of_clk_add_provider(node, of_clk_src_simple_get, clk);
@@ -251,14 +253,17 @@
 		if (rc) {
 			pr_err("%s: failed to lookup atl clock %d\n", __func__,
 			       i);
-			return -EINVAL;
+			ret = -EINVAL;
+			goto pm_put;
 		}
 
 		clk = of_clk_get_from_provider(&clkspec);
+		of_node_put(clkspec.np);
 		if (IS_ERR(clk)) {
 			pr_err("%s: failed to get atl clock %d from provider\n",
 			       __func__, i);
-			return PTR_ERR(clk);
+			ret = PTR_ERR(clk);
+			goto pm_put;
 		}
 
 		cdesc = to_atl_desc(__clk_get_hw(clk));
@@ -291,8 +296,9 @@
 		if (cdesc->enabled)
 			atl_clk_enable(__clk_get_hw(clk));
 	}
-	pm_runtime_put_sync(cinfo->dev);
 
+pm_put:
+	pm_runtime_put_sync(cinfo->dev);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/clk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/clk.c
@@ -131,7 +131,7 @@
 void __init ti_dt_clocks_register(struct ti_dt_clk oclks[])
 {
 	struct ti_dt_clk *c;
-	struct device_node *node, *parent;
+	struct device_node *node, *parent, *child;
 	struct clk *clk;
 	struct of_phandle_args clkspec;
 	char buf[64];
@@ -171,10 +171,13 @@
 		node = of_find_node_by_name(NULL, buf);
 		if (num_args && compat_mode) {
 			parent = node;
-			node = of_get_child_by_name(parent, "clock");
-			if (!node)
-				node = of_get_child_by_name(parent, "clk");
-			of_node_put(parent);
+			child = of_get_child_by_name(parent, "clock");
+			if (!child)
+				child = of_get_child_by_name(parent, "clk");
+			if (child) {
+				of_node_put(parent);
+				node = child;
+			}
 		}
 
 		clkspec.np = node;
@@ -400,6 +403,24 @@
 };
 
 /**
+ * ti_dt_clk_name - init clock name from first output name or node name
+ * @np: device node
+ *
+ * Use the first clock-output-name for the clock name if found. Fall back
+ * to legacy naming based on node name.
+ */
+const char *ti_dt_clk_name(struct device_node *np)
+{
+	const char *name;
+
+	if (!of_property_read_string_index(np, "clock-output-names", 0,
+					   &name))
+		return name;
+
+	return np->name;
+}
+
+/**
  * ti_clk_add_aliases - setup clock aliases
  *
  * Sets up any missing clock aliases. No return value.
@@ -415,7 +436,7 @@
 		clkspec.np = np;
 		clk = of_clk_get_from_provider(&clkspec);
 
-		ti_clk_add_alias(NULL, clk, np->name);
+		ti_clk_add_alias(clk, ti_dt_clk_name(np));
 	}
 }
 
@@ -468,7 +489,6 @@
 
 /**
  * ti_clk_add_alias - add a clock alias for a TI clock
- * @dev: device alias for this clock
  * @clk: clock handle to create alias for
  * @con: connection ID for this clock
  *
@@ -476,7 +496,7 @@
  * and assigns the data to it. Returns 0 if successful, negative error
  * value otherwise.
  */
-int ti_clk_add_alias(struct device *dev, struct clk *clk, const char *con)
+int ti_clk_add_alias(struct clk *clk, const char *con)
 {
 	struct clk_lookup *cl;
 
@@ -490,8 +510,6 @@
 	if (!cl)
 		return -ENOMEM;
 
-	if (dev)
-		cl->dev_id = dev_name(dev);
 	cl->con_id = con;
 	cl->clk = clk;
 
@@ -501,8 +519,8 @@
 }
 
 /**
- * ti_clk_register - register a TI clock to the common clock framework
- * @dev: device for this clock
+ * of_ti_clk_register - register a TI clock to the common clock framework
+ * @node: device node for this clock
  * @hw: hardware clock handle
  * @con: connection ID for this clock
  *
@@ -510,17 +528,18 @@
  * alias for it. Returns a handle to the registered clock if successful,
  * ERR_PTR value in failure.
  */
-struct clk *ti_clk_register(struct device *dev, struct clk_hw *hw,
-			    const char *con)
+struct clk *of_ti_clk_register(struct device_node *node, struct clk_hw *hw,
+			       const char *con)
 {
 	struct clk *clk;
 	int ret;
 
-	clk = clk_register(dev, hw);
-	if (IS_ERR(clk))
-		return clk;
+	ret = of_clk_hw_register(node, hw);
+	if (ret)
+		return ERR_PTR(ret);
 
-	ret = ti_clk_add_alias(dev, clk, con);
+	clk = hw->clk;
+	ret = ti_clk_add_alias(clk, con);
 	if (ret) {
 		clk_unregister(clk);
 		return ERR_PTR(ret);
@@ -530,8 +549,8 @@
 }
 
 /**
- * ti_clk_register_omap_hw - register a clk_hw_omap to the clock framework
- * @dev: device for this clock
+ * of_ti_clk_register_omap_hw - register a clk_hw_omap to the clock framework
+ * @node: device node for this clock
  * @hw: hardware clock handle
  * @con: connection ID for this clock
  *
@@ -540,13 +559,13 @@
  * Returns a handle to the registered clock if successful, ERR_PTR value
  * in failure.
  */
-struct clk *ti_clk_register_omap_hw(struct device *dev, struct clk_hw *hw,
-				    const char *con)
+struct clk *of_ti_clk_register_omap_hw(struct device_node *node,
+				       struct clk_hw *hw, const char *con)
 {
 	struct clk *clk;
 	struct clk_hw_omap *oclk;
 
-	clk = ti_clk_register(dev, hw, con);
+	clk = of_ti_clk_register(node, hw, con);
 	if (IS_ERR(clk))
 		return clk;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/clkctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/clkctrl.c
@@ -267,6 +267,9 @@
 	if (clkctrl_name && !legacy_naming) {
 		clock_name = kasprintf(GFP_KERNEL, "%s-clkctrl:%04x:%d",
 				       clkctrl_name, offset, index);
+		if (!clock_name)
+			return NULL;
+
 		strreplace(clock_name, '_', '-');
 
 		return clock_name;
@@ -314,7 +317,7 @@
 	init.ops = ops;
 	init.flags = 0;
 
-	clk = ti_clk_register(NULL, clk_hw, init.name);
+	clk = of_ti_clk_register(node, clk_hw, init.name);
 	if (IS_ERR_OR_NULL(clk)) {
 		ret = -EINVAL;
 		goto cleanup;
@@ -598,6 +601,10 @@
 	if (clkctrl_name) {
 		provider->clkdm_name = kasprintf(GFP_KERNEL,
 						 "%s_clkdm", clkctrl_name);
+		if (!provider->clkdm_name) {
+			kfree(provider);
+			return;
+		}
 		goto clkdm_found;
 	}
 
@@ -694,7 +701,7 @@
 		init.ops = &omap4_clkctrl_clk_ops;
 		hw->hw.init = &init;
 
-		clk = ti_clk_register_omap_hw(NULL, &hw->hw, init.name);
+		clk = of_ti_clk_register_omap_hw(node, &hw->hw, init.name);
 		if (IS_ERR_OR_NULL(clk))
 			goto cleanup;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/clock.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/clock.h
@@ -210,11 +210,12 @@
 
 typedef void (*ti_of_clk_init_cb_t)(void *, struct device_node *);
 
-struct clk *ti_clk_register(struct device *dev, struct clk_hw *hw,
-			    const char *con);
-struct clk *ti_clk_register_omap_hw(struct device *dev, struct clk_hw *hw,
-				    const char *con);
-int ti_clk_add_alias(struct device *dev, struct clk *clk, const char *con);
+struct clk *of_ti_clk_register(struct device_node *node, struct clk_hw *hw,
+			       const char *con);
+struct clk *of_ti_clk_register_omap_hw(struct device_node *node,
+				       struct clk_hw *hw, const char *con);
+const char *ti_dt_clk_name(struct device_node *np);
+int ti_clk_add_alias(struct clk *clk, const char *con);
 void ti_clk_add_aliases(void);
 
 void ti_clk_latch(struct clk_omap_reg *reg, s8 shift);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/clockdomain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/clockdomain.c
@@ -131,7 +131,7 @@
 {
 	struct clk *clk;
 	struct clk_hw *clk_hw;
-	const char *clkdm_name = node->name;
+	const char *clkdm_name = ti_dt_clk_name(node);
 	int i;
 	unsigned int num_clks;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/composite.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/composite.c
@@ -125,6 +125,7 @@
 	struct component_clk *comp;
 	int num_parents = 0;
 	const char **parent_names = NULL;
+	const char *name;
 	int i;
 	int ret;
 
@@ -172,7 +173,8 @@
 		goto cleanup;
 	}
 
-	clk = clk_register_composite(NULL, node->name,
+	name = ti_dt_clk_name(node);
+	clk = clk_register_composite(NULL, name,
 				     parent_names, num_parents,
 				     _get_hw(cclk, CLK_COMPONENT_TYPE_MUX),
 				     &ti_clk_mux_ops,
@@ -182,7 +184,7 @@
 				     &ti_composite_gate_ops, 0);
 
 	if (!IS_ERR(clk)) {
-		ret = ti_clk_add_alias(NULL, clk, node->name);
+		ret = ti_clk_add_alias(clk, name);
 		if (ret) {
 			clk_unregister(clk);
 			goto cleanup;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/divider.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/divider.c
@@ -317,13 +317,14 @@
 				     u32 flags,
 				     struct clk_omap_divider *div)
 {
-	struct clk *clk;
 	struct clk_init_data init;
 	const char *parent_name;
+	const char *name;
 
 	parent_name = of_clk_get_parent_name(node, 0);
 
-	init.name = node->name;
+	name = ti_dt_clk_name(node);
+	init.name = name;
 	init.ops = &ti_clk_divider_ops;
 	init.flags = flags;
 	init.parent_names = (parent_name ? &parent_name : NULL);
@@ -332,12 +333,7 @@
 	div->hw.init = &init;
 
 	/* register the clock */
-	clk = ti_clk_register(NULL, &div->hw, node->name);
-
-	if (IS_ERR(clk))
-		kfree(div);
-
-	return clk;
+	return of_ti_clk_register(node, &div->hw, name);
 }
 
 int ti_clk_parse_divider_data(int *div_table, int num_dividers, int max_div,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/dpll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/dpll.c
@@ -164,6 +164,7 @@
 	struct clk_hw *hw = user;
 	struct clk_hw_omap *clk_hw = to_clk_hw_omap(hw);
 	struct dpll_data *dd = clk_hw->dpll_data;
+	const char *name;
 	struct clk *clk;
 	const struct clk_init_data *init = hw->init;
 
@@ -193,7 +194,8 @@
 	dd->clk_bypass = __clk_get_hw(clk);
 
 	/* register the clock */
-	clk = ti_clk_register_omap_hw(NULL, &clk_hw->hw, node->name);
+	name = ti_dt_clk_name(node);
+	clk = of_ti_clk_register_omap_hw(node, &clk_hw->hw, name);
 
 	if (!IS_ERR(clk)) {
 		of_clk_add_provider(node, of_clk_src_simple_get, clk);
@@ -227,7 +229,7 @@
 	struct clk *clk;
 	struct clk_init_data init = { NULL };
 	struct clk_hw_omap *clk_hw;
-	const char *name = node->name;
+	const char *name = ti_dt_clk_name(node);
 	const char *parent_name;
 
 	parent_name = of_clk_get_parent_name(node, 0);
@@ -265,7 +267,7 @@
 #endif
 
 	/* register the clock */
-	clk = ti_clk_register_omap_hw(NULL, &clk_hw->hw, name);
+	clk = of_ti_clk_register_omap_hw(node, &clk_hw->hw, name);
 
 	if (IS_ERR(clk))
 		kfree(clk_hw);
@@ -304,7 +306,7 @@
 	clk_hw->ops = &clkhwops_omap3_dpll;
 	clk_hw->hw.init = init;
 
-	init->name = node->name;
+	init->name = ti_dt_clk_name(node);
 	init->ops = ops;
 
 	init->num_parents = of_clk_get_parent_count(node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/fapll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/fapll.c
@@ -19,6 +19,8 @@
 #include <linux/of_address.h>
 #include <linux/clk/ti.h>
 
+#include "clock.h"
+
 /* FAPLL Control Register PLL_CTRL */
 #define FAPLL_MAIN_MULT_N_SHIFT	16
 #define FAPLL_MAIN_DIV_P_SHIFT	8
@@ -542,6 +544,7 @@
 	struct clk_init_data *init = NULL;
 	const char *parent_name[2];
 	struct clk *pll_clk;
+	const char *name;
 	int i;
 
 	fd = kzalloc(sizeof(*fd), GFP_KERNEL);
@@ -559,7 +562,8 @@
 		goto free;
 
 	init->ops = &ti_fapll_ops;
-	init->name = node->name;
+	name = ti_dt_clk_name(node);
+	init->name = name;
 
 	init->num_parents = of_clk_get_parent_count(node);
 	if (init->num_parents != 2) {
@@ -591,7 +595,7 @@
 	if (fapll_is_ddr_pll(fd->base))
 		fd->bypass_bit_inverted = true;
 
-	fd->name = node->name;
+	fd->name = name;
 	fd->hw.init = init;
 
 	/* Register the parent PLL */
@@ -638,8 +642,7 @@
 				freq = NULL;
 		}
 		synth_clk = ti_fapll_synth_setup(fd, freq, div, output_instance,
-						 output_name, node->name,
-						 pll_clk);
+						 output_name, name, pll_clk);
 		if (IS_ERR(synth_clk))
 			continue;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/fixed-factor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/fixed-factor.c
@@ -36,7 +36,7 @@
 static void __init of_ti_fixed_factor_clk_setup(struct device_node *node)
 {
 	struct clk *clk;
-	const char *clk_name = node->name;
+	const char *clk_name = ti_dt_clk_name(node);
 	const char *parent_name;
 	u32 div, mult;
 	u32 flags = 0;
@@ -62,7 +62,7 @@
 	if (!IS_ERR(clk)) {
 		of_clk_add_provider(node, of_clk_src_simple_get, clk);
 		of_ti_clk_autoidle_setup(node);
-		ti_clk_add_alias(NULL, clk, clk_name);
+		ti_clk_add_alias(clk, clk_name);
 	}
 }
 CLK_OF_DECLARE(ti_fixed_factor_clk, "ti,fixed-factor-clock",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/gate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/gate.c
@@ -93,7 +93,7 @@
 	return ret;
 }
 
-static struct clk *_register_gate(struct device *dev, const char *name,
+static struct clk *_register_gate(struct device_node *node, const char *name,
 				  const char *parent_name, unsigned long flags,
 				  struct clk_omap_reg *reg, u8 bit_idx,
 				  u8 clk_gate_flags, const struct clk_ops *ops,
@@ -123,7 +123,7 @@
 
 	init.flags = flags;
 
-	clk = ti_clk_register_omap_hw(NULL, &clk_hw->hw, name);
+	clk = of_ti_clk_register_omap_hw(node, &clk_hw->hw, name);
 
 	if (IS_ERR(clk))
 		kfree(clk_hw);
@@ -138,6 +138,7 @@
 	struct clk *clk;
 	const char *parent_name;
 	struct clk_omap_reg reg;
+	const char *name;
 	u8 enable_bit = 0;
 	u32 val;
 	u32 flags = 0;
@@ -164,7 +165,8 @@
 	if (of_property_read_bool(node, "ti,set-bit-to-disable"))
 		clk_gate_flags |= INVERT_ENABLE;
 
-	clk = _register_gate(NULL, node->name, parent_name, flags, &reg,
+	name = ti_dt_clk_name(node);
+	clk = _register_gate(node, name, parent_name, flags, &reg,
 			     enable_bit, clk_gate_flags, ops, hw_ops);
 
 	if (!IS_ERR(clk))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/interface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/interface.c
@@ -32,7 +32,8 @@
 	.is_enabled	= &omap2_dflt_clk_is_enabled,
 };
 
-static struct clk *_register_interface(struct device *dev, const char *name,
+static struct clk *_register_interface(struct device_node *node,
+				       const char *name,
 				       const char *parent_name,
 				       struct clk_omap_reg *reg, u8 bit_idx,
 				       const struct clk_hw_omap_ops *ops)
@@ -57,7 +58,7 @@
 	init.num_parents = 1;
 	init.parent_names = &parent_name;
 
-	clk = ti_clk_register_omap_hw(NULL, &clk_hw->hw, name);
+	clk = of_ti_clk_register_omap_hw(node, &clk_hw->hw, name);
 
 	if (IS_ERR(clk))
 		kfree(clk_hw);
@@ -72,6 +73,7 @@
 	const char *parent_name;
 	struct clk_omap_reg reg;
 	u8 enable_bit = 0;
+	const char *name;
 	u32 val;
 
 	if (ti_clk_get_reg_addr(node, 0, &reg))
@@ -86,7 +88,8 @@
 		return;
 	}
 
-	clk = _register_interface(NULL, node->name, parent_name, &reg,
+	name = ti_dt_clk_name(node);
+	clk = _register_interface(node, name, parent_name, &reg,
 				  enable_bit, ops);
 
 	if (!IS_ERR(clk))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/ti/mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/ti/mux.c
@@ -126,7 +126,7 @@
 	.restore_context = clk_mux_restore_context,
 };
 
-static struct clk *_register_mux(struct device *dev, const char *name,
+static struct clk *_register_mux(struct device_node *node, const char *name,
 				 const char * const *parent_names,
 				 u8 num_parents, unsigned long flags,
 				 struct clk_omap_reg *reg, u8 shift, u32 mask,
@@ -156,7 +156,7 @@
 	mux->table = table;
 	mux->hw.init = &init;
 
-	clk = ti_clk_register(dev, &mux->hw, name);
+	clk = of_ti_clk_register(node, &mux->hw, name);
 
 	if (IS_ERR(clk))
 		kfree(mux);
@@ -176,6 +176,7 @@
 	struct clk_omap_reg reg;
 	unsigned int num_parents;
 	const char **parent_names;
+	const char *name;
 	u8 clk_mux_flags = 0;
 	u32 mask = 0;
 	u32 shift = 0;
@@ -213,7 +214,8 @@
 
 	mask = (1 << fls(mask)) - 1;
 
-	clk = _register_mux(NULL, node->name, parent_names, num_parents,
+	name = ti_dt_clk_name(node);
+	clk = _register_mux(node, name, parent_names, num_parents,
 			    flags, &reg, shift, mask, latch, clk_mux_flags,
 			    NULL);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/uniphier/clk-uniphier-fixed-rate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/uniphier/clk-uniphier-fixed-rate.c
@@ -24,6 +24,7 @@
 
 	init.name = name;
 	init.ops = &clk_fixed_rate_ops;
+	init.flags = 0;
 	init.parent_names = NULL;
 	init.num_parents = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/x86/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/x86/Kconfig
@@ -1,8 +1,9 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config CLK_LGM_CGU
 	depends on OF && HAS_IOMEM && (X86 || COMPILE_TEST)
+	select MFD_SYSCON
 	select OF_EARLY_FLATTREE
 	bool "Clock driver for Lightning Mountain(LGM) platform"
 	help
-	  Clock Generation Unit(CGU) driver for Intel Lightning Mountain(LGM)
-	  network processor SoC.
+	  Clock Generation Unit(CGU) driver for MaxLinear's x86 based
+	  Lightning Mountain(LGM) network processor SoC.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/x86/clk-cgu-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/x86/clk-cgu-pll.c
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
+ * Copyright (C) 2020-2022 MaxLinear, Inc.
  * Copyright (C) 2020 Intel Corporation.
- * Zhu YiXin <yixin.zhu@intel.com>
- * Rahul Tanwar <rahul.tanwar@intel.com>
+ * Zhu Yixin <yzhu@maxlinear.com>
+ * Rahul Tanwar <rtanwar@maxlinear.com>
  */
 
 #include <linux/clk-provider.h>
@@ -40,13 +41,10 @@
 {
 	struct lgm_clk_pll *pll = to_lgm_clk_pll(hw);
 	unsigned int div, mult, frac;
-	unsigned long flags;
 
-	spin_lock_irqsave(&pll->lock, flags);
 	mult = lgm_get_clk_val(pll->membase, PLL_REF_DIV(pll->reg), 0, 12);
 	div = lgm_get_clk_val(pll->membase, PLL_REF_DIV(pll->reg), 18, 6);
 	frac = lgm_get_clk_val(pll->membase, pll->reg, 2, 24);
-	spin_unlock_irqrestore(&pll->lock, flags);
 
 	if (pll->type == TYPE_LJPLL)
 		div *= 4;
@@ -57,12 +55,9 @@
 static int lgm_pll_is_enabled(struct clk_hw *hw)
 {
 	struct lgm_clk_pll *pll = to_lgm_clk_pll(hw);
-	unsigned long flags;
 	unsigned int ret;
 
-	spin_lock_irqsave(&pll->lock, flags);
 	ret = lgm_get_clk_val(pll->membase, pll->reg, 0, 1);
-	spin_unlock_irqrestore(&pll->lock, flags);
 
 	return ret;
 }
@@ -70,15 +65,13 @@
 static int lgm_pll_enable(struct clk_hw *hw)
 {
 	struct lgm_clk_pll *pll = to_lgm_clk_pll(hw);
-	unsigned long flags;
 	u32 val;
 	int ret;
 
-	spin_lock_irqsave(&pll->lock, flags);
 	lgm_set_clk_val(pll->membase, pll->reg, 0, 1, 1);
-	ret = readl_poll_timeout_atomic(pll->membase + pll->reg,
-					val, (val & 0x1), 1, 100);
-	spin_unlock_irqrestore(&pll->lock, flags);
+	ret = regmap_read_poll_timeout_atomic(pll->membase, pll->reg,
+					      val, (val & 0x1), 1, 100);
+
 
 	return ret;
 }
@@ -86,11 +79,8 @@
 static void lgm_pll_disable(struct clk_hw *hw)
 {
 	struct lgm_clk_pll *pll = to_lgm_clk_pll(hw);
-	unsigned long flags;
 
-	spin_lock_irqsave(&pll->lock, flags);
 	lgm_set_clk_val(pll->membase, pll->reg, 0, 1, 0);
-	spin_unlock_irqrestore(&pll->lock, flags);
 }
 
 static const struct clk_ops lgm_pll_ops = {
@@ -121,7 +111,6 @@
 		return ERR_PTR(-ENOMEM);
 
 	pll->membase = ctx->membase;
-	pll->lock = ctx->lock;
 	pll->reg = list->reg;
 	pll->flags = list->flags;
 	pll->type = list->type;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/x86/clk-cgu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/x86/clk-cgu.c
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
+ * Copyright (C) 2020-2022 MaxLinear, Inc.
  * Copyright (C) 2020 Intel Corporation.
- * Zhu YiXin <yixin.zhu@intel.com>
- * Rahul Tanwar <rahul.tanwar@intel.com>
+ * Zhu Yixin <yzhu@maxlinear.com>
+ * Rahul Tanwar <rtanwar@maxlinear.com>
  */
 #include <linux/clk-provider.h>
 #include <linux/device.h>
@@ -24,14 +25,10 @@
 static struct clk_hw *lgm_clk_register_fixed(struct lgm_clk_provider *ctx,
 					     const struct lgm_clk_branch *list)
 {
-	unsigned long flags;
 
-	if (list->div_flags & CLOCK_FLAG_VAL_INIT) {
-		spin_lock_irqsave(&ctx->lock, flags);
+	if (list->div_flags & CLOCK_FLAG_VAL_INIT)
 		lgm_set_clk_val(ctx->membase, list->div_off, list->div_shift,
 				list->div_width, list->div_val);
-		spin_unlock_irqrestore(&ctx->lock, flags);
-	}
 
 	return clk_hw_register_fixed_rate(NULL, list->name,
 					  list->parent_data[0].name,
@@ -41,33 +38,27 @@
 static u8 lgm_clk_mux_get_parent(struct clk_hw *hw)
 {
 	struct lgm_clk_mux *mux = to_lgm_clk_mux(hw);
-	unsigned long flags;
 	u32 val;
 
-	spin_lock_irqsave(&mux->lock, flags);
 	if (mux->flags & MUX_CLK_SW)
 		val = mux->reg;
 	else
 		val = lgm_get_clk_val(mux->membase, mux->reg, mux->shift,
 				      mux->width);
-	spin_unlock_irqrestore(&mux->lock, flags);
 	return clk_mux_val_to_index(hw, NULL, mux->flags, val);
 }
 
 static int lgm_clk_mux_set_parent(struct clk_hw *hw, u8 index)
 {
 	struct lgm_clk_mux *mux = to_lgm_clk_mux(hw);
-	unsigned long flags;
 	u32 val;
 
 	val = clk_mux_index_to_val(NULL, mux->flags, index);
-	spin_lock_irqsave(&mux->lock, flags);
 	if (mux->flags & MUX_CLK_SW)
 		mux->reg = val;
 	else
 		lgm_set_clk_val(mux->membase, mux->reg, mux->shift,
 				mux->width, val);
-	spin_unlock_irqrestore(&mux->lock, flags);
 
 	return 0;
 }
@@ -90,7 +81,7 @@
 lgm_clk_register_mux(struct lgm_clk_provider *ctx,
 		     const struct lgm_clk_branch *list)
 {
-	unsigned long flags, cflags = list->mux_flags;
+	unsigned long cflags = list->mux_flags;
 	struct device *dev = ctx->dev;
 	u8 shift = list->mux_shift;
 	u8 width = list->mux_width;
@@ -111,7 +102,6 @@
 	init.num_parents = list->num_parents;
 
 	mux->membase = ctx->membase;
-	mux->lock = ctx->lock;
 	mux->reg = reg;
 	mux->shift = shift;
 	mux->width = width;
@@ -123,11 +113,8 @@
 	if (ret)
 		return ERR_PTR(ret);
 
-	if (cflags & CLOCK_FLAG_VAL_INIT) {
-		spin_lock_irqsave(&mux->lock, flags);
+	if (cflags & CLOCK_FLAG_VAL_INIT)
 		lgm_set_clk_val(mux->membase, reg, shift, width, list->mux_val);
-		spin_unlock_irqrestore(&mux->lock, flags);
-	}
 
 	return hw;
 }
@@ -136,13 +123,10 @@
 lgm_clk_divider_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
 {
 	struct lgm_clk_divider *divider = to_lgm_clk_divider(hw);
-	unsigned long flags;
 	unsigned int val;
 
-	spin_lock_irqsave(&divider->lock, flags);
 	val = lgm_get_clk_val(divider->membase, divider->reg,
 			      divider->shift, divider->width);
-	spin_unlock_irqrestore(&divider->lock, flags);
 
 	return divider_recalc_rate(hw, parent_rate, val, divider->table,
 				   divider->flags, divider->width);
@@ -163,7 +147,6 @@
 			 unsigned long prate)
 {
 	struct lgm_clk_divider *divider = to_lgm_clk_divider(hw);
-	unsigned long flags;
 	int value;
 
 	value = divider_get_val(rate, prate, divider->table,
@@ -171,10 +154,8 @@
 	if (value < 0)
 		return value;
 
-	spin_lock_irqsave(&divider->lock, flags);
 	lgm_set_clk_val(divider->membase, divider->reg,
 			divider->shift, divider->width, value);
-	spin_unlock_irqrestore(&divider->lock, flags);
 
 	return 0;
 }
@@ -182,12 +163,10 @@
 static int lgm_clk_divider_enable_disable(struct clk_hw *hw, int enable)
 {
 	struct lgm_clk_divider *div = to_lgm_clk_divider(hw);
-	unsigned long flags;
 
-	spin_lock_irqsave(&div->lock, flags);
-	lgm_set_clk_val(div->membase, div->reg, div->shift_gate,
-			div->width_gate, enable);
-	spin_unlock_irqrestore(&div->lock, flags);
+	if (div->flags != DIV_CLK_NO_MASK)
+		lgm_set_clk_val(div->membase, div->reg, div->shift_gate,
+				div->width_gate, enable);
 	return 0;
 }
 
@@ -213,7 +192,7 @@
 lgm_clk_register_divider(struct lgm_clk_provider *ctx,
 			 const struct lgm_clk_branch *list)
 {
-	unsigned long flags, cflags = list->div_flags;
+	unsigned long cflags = list->div_flags;
 	struct device *dev = ctx->dev;
 	struct lgm_clk_divider *div;
 	struct clk_init_data init = {};
@@ -236,7 +215,6 @@
 	init.num_parents = 1;
 
 	div->membase = ctx->membase;
-	div->lock = ctx->lock;
 	div->reg = reg;
 	div->shift = shift;
 	div->width = width;
@@ -251,11 +229,8 @@
 	if (ret)
 		return ERR_PTR(ret);
 
-	if (cflags & CLOCK_FLAG_VAL_INIT) {
-		spin_lock_irqsave(&div->lock, flags);
+	if (cflags & CLOCK_FLAG_VAL_INIT)
 		lgm_set_clk_val(div->membase, reg, shift, width, list->div_val);
-		spin_unlock_irqrestore(&div->lock, flags);
-	}
 
 	return hw;
 }
@@ -264,7 +239,6 @@
 lgm_clk_register_fixed_factor(struct lgm_clk_provider *ctx,
 			      const struct lgm_clk_branch *list)
 {
-	unsigned long flags;
 	struct clk_hw *hw;
 
 	hw = clk_hw_register_fixed_factor(ctx->dev, list->name,
@@ -273,12 +247,9 @@
 	if (IS_ERR(hw))
 		return ERR_CAST(hw);
 
-	if (list->div_flags & CLOCK_FLAG_VAL_INIT) {
-		spin_lock_irqsave(&ctx->lock, flags);
+	if (list->div_flags & CLOCK_FLAG_VAL_INIT)
 		lgm_set_clk_val(ctx->membase, list->div_off, list->div_shift,
 				list->div_width, list->div_val);
-		spin_unlock_irqrestore(&ctx->lock, flags);
-	}
 
 	return hw;
 }
@@ -286,13 +257,10 @@
 static int lgm_clk_gate_enable(struct clk_hw *hw)
 {
 	struct lgm_clk_gate *gate = to_lgm_clk_gate(hw);
-	unsigned long flags;
 	unsigned int reg;
 
-	spin_lock_irqsave(&gate->lock, flags);
 	reg = GATE_HW_REG_EN(gate->reg);
 	lgm_set_clk_val(gate->membase, reg, gate->shift, 1, 1);
-	spin_unlock_irqrestore(&gate->lock, flags);
 
 	return 0;
 }
@@ -300,25 +268,19 @@
 static void lgm_clk_gate_disable(struct clk_hw *hw)
 {
 	struct lgm_clk_gate *gate = to_lgm_clk_gate(hw);
-	unsigned long flags;
 	unsigned int reg;
 
-	spin_lock_irqsave(&gate->lock, flags);
 	reg = GATE_HW_REG_DIS(gate->reg);
 	lgm_set_clk_val(gate->membase, reg, gate->shift, 1, 1);
-	spin_unlock_irqrestore(&gate->lock, flags);
 }
 
 static int lgm_clk_gate_is_enabled(struct clk_hw *hw)
 {
 	struct lgm_clk_gate *gate = to_lgm_clk_gate(hw);
 	unsigned int reg, ret;
-	unsigned long flags;
 
-	spin_lock_irqsave(&gate->lock, flags);
 	reg = GATE_HW_REG_STAT(gate->reg);
 	ret = lgm_get_clk_val(gate->membase, reg, gate->shift, 1);
-	spin_unlock_irqrestore(&gate->lock, flags);
 
 	return ret;
 }
@@ -333,7 +295,7 @@
 lgm_clk_register_gate(struct lgm_clk_provider *ctx,
 		      const struct lgm_clk_branch *list)
 {
-	unsigned long flags, cflags = list->gate_flags;
+	unsigned long cflags = list->gate_flags;
 	const char *pname = list->parent_data[0].name;
 	struct device *dev = ctx->dev;
 	u8 shift = list->gate_shift;
@@ -354,7 +316,6 @@
 	init.num_parents = pname ? 1 : 0;
 
 	gate->membase = ctx->membase;
-	gate->lock = ctx->lock;
 	gate->reg = reg;
 	gate->shift = shift;
 	gate->flags = cflags;
@@ -366,9 +327,7 @@
 		return ERR_PTR(ret);
 
 	if (cflags & CLOCK_FLAG_VAL_INIT) {
-		spin_lock_irqsave(&gate->lock, flags);
 		lgm_set_clk_val(gate->membase, reg, shift, 1, list->gate_val);
-		spin_unlock_irqrestore(&gate->lock, flags);
 	}
 
 	return hw;
@@ -396,8 +355,22 @@
 			hw = lgm_clk_register_fixed_factor(ctx, list);
 			break;
 		case CLK_TYPE_GATE:
-			hw = lgm_clk_register_gate(ctx, list);
+			if (list->gate_flags & GATE_CLK_HW) {
+				hw = lgm_clk_register_gate(ctx, list);
+			} else {
+				/*
+				 * GATE_CLKs can be controlled either from
+				 * CGU clk driver i.e. this driver or directly
+				 * from power management driver/daemon. It is
+				 * dependent on the power policy/profile requirements
+				 * of the end product. To override control of gate
+				 * clks from this driver, provide NULL for this index
+				 * of gate clk provider.
+				 */
+				hw = NULL;
+			}
 			break;
+
 		default:
 			dev_err(ctx->dev, "invalid clk type\n");
 			return -EINVAL;
@@ -443,24 +416,18 @@
 static int lgm_clk_ddiv_enable(struct clk_hw *hw)
 {
 	struct lgm_clk_ddiv *ddiv = to_lgm_clk_ddiv(hw);
-	unsigned long flags;
 
-	spin_lock_irqsave(&ddiv->lock, flags);
 	lgm_set_clk_val(ddiv->membase, ddiv->reg, ddiv->shift_gate,
 			ddiv->width_gate, 1);
-	spin_unlock_irqrestore(&ddiv->lock, flags);
 	return 0;
 }
 
 static void lgm_clk_ddiv_disable(struct clk_hw *hw)
 {
 	struct lgm_clk_ddiv *ddiv = to_lgm_clk_ddiv(hw);
-	unsigned long flags;
 
-	spin_lock_irqsave(&ddiv->lock, flags);
 	lgm_set_clk_val(ddiv->membase, ddiv->reg, ddiv->shift_gate,
 			ddiv->width_gate, 0);
-	spin_unlock_irqrestore(&ddiv->lock, flags);
 }
 
 static int
@@ -497,32 +464,25 @@
 {
 	struct lgm_clk_ddiv *ddiv = to_lgm_clk_ddiv(hw);
 	u32 div, ddiv1, ddiv2;
-	unsigned long flags;
 
 	div = DIV_ROUND_CLOSEST_ULL((u64)prate, rate);
 
-	spin_lock_irqsave(&ddiv->lock, flags);
 	if (lgm_get_clk_val(ddiv->membase, ddiv->reg, ddiv->shift2, 1)) {
 		div = DIV_ROUND_CLOSEST_ULL((u64)div, 5);
 		div = div * 2;
 	}
 
-	if (div <= 0) {
-		spin_unlock_irqrestore(&ddiv->lock, flags);
+	if (div <= 0)
 		return -EINVAL;
-	}
 
-	if (lgm_clk_get_ddiv_val(div, &ddiv1, &ddiv2)) {
-		spin_unlock_irqrestore(&ddiv->lock, flags);
+	if (lgm_clk_get_ddiv_val(div, &ddiv1, &ddiv2))
 		return -EINVAL;
-	}
 
 	lgm_set_clk_val(ddiv->membase, ddiv->reg, ddiv->shift0, ddiv->width0,
 			ddiv1 - 1);
 
 	lgm_set_clk_val(ddiv->membase, ddiv->reg,  ddiv->shift1, ddiv->width1,
 			ddiv2 - 1);
-	spin_unlock_irqrestore(&ddiv->lock, flags);
 
 	return 0;
 }
@@ -533,18 +493,15 @@
 {
 	struct lgm_clk_ddiv *ddiv = to_lgm_clk_ddiv(hw);
 	u32 div, ddiv1, ddiv2;
-	unsigned long flags;
 	u64 rate64;
 
 	div = DIV_ROUND_CLOSEST_ULL((u64)*prate, rate);
 
 	/* if predivide bit is enabled, modify div by factor of 2.5 */
-	spin_lock_irqsave(&ddiv->lock, flags);
 	if (lgm_get_clk_val(ddiv->membase, ddiv->reg, ddiv->shift2, 1)) {
 		div = div * 2;
 		div = DIV_ROUND_CLOSEST_ULL((u64)div, 5);
 	}
-	spin_unlock_irqrestore(&ddiv->lock, flags);
 
 	if (div <= 0)
 		return *prate;
@@ -558,12 +515,10 @@
 	do_div(rate64, ddiv2);
 
 	/* if predivide bit is enabled, modify rounded rate by factor of 2.5 */
-	spin_lock_irqsave(&ddiv->lock, flags);
 	if (lgm_get_clk_val(ddiv->membase, ddiv->reg, ddiv->shift2, 1)) {
 		rate64 = rate64 * 2;
 		rate64 = DIV_ROUND_CLOSEST_ULL(rate64, 5);
 	}
-	spin_unlock_irqrestore(&ddiv->lock, flags);
 
 	return rate64;
 }
@@ -600,7 +555,6 @@
 		init.num_parents = 1;
 
 		ddiv->membase = ctx->membase;
-		ddiv->lock = ctx->lock;
 		ddiv->reg = list->reg;
 		ddiv->shift0 = list->shift0;
 		ddiv->width0 = list->width0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/x86/clk-cgu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/x86/clk-cgu.h
@@ -1,28 +1,28 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
- * Copyright(c) 2020 Intel Corporation.
- * Zhu YiXin <yixin.zhu@intel.com>
- * Rahul Tanwar <rahul.tanwar@intel.com>
+ * Copyright (C) 2020-2022 MaxLinear, Inc.
+ * Copyright (C) 2020 Intel Corporation.
+ * Zhu Yixin <yzhu@maxlinear.com>
+ * Rahul Tanwar <rtanwar@maxlinear.com>
  */
 
 #ifndef __CLK_CGU_H
 #define __CLK_CGU_H
 
-#include <linux/io.h>
+#include <linux/regmap.h>
 
 struct lgm_clk_mux {
 	struct clk_hw hw;
-	void __iomem *membase;
+	struct regmap *membase;
 	unsigned int reg;
 	u8 shift;
 	u8 width;
 	unsigned long flags;
-	spinlock_t lock;
 };
 
 struct lgm_clk_divider {
 	struct clk_hw hw;
-	void __iomem *membase;
+	struct regmap *membase;
 	unsigned int reg;
 	u8 shift;
 	u8 width;
@@ -30,12 +30,11 @@
 	u8 width_gate;
 	unsigned long flags;
 	const struct clk_div_table *table;
-	spinlock_t lock;
 };
 
 struct lgm_clk_ddiv {
 	struct clk_hw hw;
-	void __iomem *membase;
+	struct regmap *membase;
 	unsigned int reg;
 	u8 shift0;
 	u8 width0;
@@ -48,16 +47,14 @@
 	unsigned int mult;
 	unsigned int div;
 	unsigned long flags;
-	spinlock_t lock;
 };
 
 struct lgm_clk_gate {
 	struct clk_hw hw;
-	void __iomem *membase;
+	struct regmap *membase;
 	unsigned int reg;
 	u8 shift;
 	unsigned long flags;
-	spinlock_t lock;
 };
 
 enum lgm_clk_type {
@@ -77,11 +74,10 @@
  * @clk_data: array of hw clocks and clk number.
  */
 struct lgm_clk_provider {
-	void __iomem *membase;
+	struct regmap *membase;
 	struct device_node *np;
 	struct device *dev;
 	struct clk_hw_onecell_data clk_data;
-	spinlock_t lock;
 };
 
 enum pll_type {
@@ -92,11 +88,10 @@
 
 struct lgm_clk_pll {
 	struct clk_hw hw;
-	void __iomem *membase;
+	struct regmap *membase;
 	unsigned int reg;
 	unsigned long flags;
 	enum pll_type type;
-	spinlock_t lock;
 };
 
 /**
@@ -202,6 +197,8 @@
 /* clock flags definition */
 #define CLOCK_FLAG_VAL_INIT	BIT(16)
 #define MUX_CLK_SW		BIT(17)
+#define GATE_CLK_HW		BIT(18)
+#define DIV_CLK_NO_MASK		BIT(19)
 
 #define LGM_MUX(_id, _name, _pdata, _f, _reg,		\
 		_shift, _width, _cf, _v)		\
@@ -300,29 +297,32 @@
 		.div = _d,					\
 	}
 
-static inline void lgm_set_clk_val(void __iomem *membase, u32 reg,
+static inline void lgm_set_clk_val(struct regmap *membase, u32 reg,
 				   u8 shift, u8 width, u32 set_val)
 {
 	u32 mask = (GENMASK(width - 1, 0) << shift);
-	u32 regval;
 
-	regval = readl(membase + reg);
-	regval = (regval & ~mask) | ((set_val << shift) & mask);
-	writel(regval, membase + reg);
+	regmap_update_bits(membase, reg, mask, set_val << shift);
 }
 
-static inline u32 lgm_get_clk_val(void __iomem *membase, u32 reg,
+static inline u32 lgm_get_clk_val(struct regmap *membase, u32 reg,
 				  u8 shift, u8 width)
 {
 	u32 mask = (GENMASK(width - 1, 0) << shift);
 	u32 val;
 
-	val = readl(membase + reg);
+	if (regmap_read(membase, reg, &val)) {
+		WARN_ONCE(1, "Failed to read clk reg: 0x%x\n", reg);
+		return 0;
+	}
+
 	val = (val & mask) >> shift;
 
 	return val;
 }
 
+
+
 int lgm_clk_register_branches(struct lgm_clk_provider *ctx,
 			      const struct lgm_clk_branch *list,
 			      unsigned int nr_clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/x86/clk-lgm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/x86/clk-lgm.c
@@ -1,10 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
+ * Copyright (C) 2020-2022 MaxLinear, Inc.
  * Copyright (C) 2020 Intel Corporation.
- * Zhu YiXin <yixin.zhu@intel.com>
- * Rahul Tanwar <rahul.tanwar@intel.com>
+ * Zhu Yixin <yzhu@maxlinear.com>
+ * Rahul Tanwar <rtanwar@maxlinear.com>
  */
 #include <linux/clk-provider.h>
+#include <linux/mfd/syscon.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <dt-bindings/clock/intel,lgm-clk.h>
@@ -253,8 +255,8 @@
 	LGM_FIXED(LGM_CLK_SLIC, "slic", NULL, 0, CGU_IF_CLK1,
 		  8, 2, CLOCK_FLAG_VAL_INIT, 8192000, 2),
 	LGM_FIXED(LGM_CLK_DOCSIS, "v_docsis", NULL, 0, 0, 0, 0, 0, 16000000, 0),
-	LGM_DIV(LGM_CLK_DCL, "dcl", "v_ifclk", 0, CGU_PCMCR,
-		25, 3, 0, 0, 0, 0, dcl_div),
+	LGM_DIV(LGM_CLK_DCL, "dcl", "v_ifclk", CLK_SET_RATE_PARENT, CGU_PCMCR,
+		25, 3, 0, 0, DIV_CLK_NO_MASK, 0, dcl_div),
 	LGM_MUX(LGM_CLK_PCM, "pcm", pcm_p, 0, CGU_C55_PCMCR,
 		0, 1, CLK_MUX_ROUND_CLOSEST, 0),
 	LGM_FIXED_FACTOR(LGM_CLK_DDR_PHY, "ddr_phy", "ddr",
@@ -433,13 +435,15 @@
 
 	ctx->clk_data.num = CLK_NR_CLKS;
 
-	ctx->membase = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(ctx->membase))
+	ctx->membase = syscon_node_to_regmap(np);
+	if (IS_ERR(ctx->membase)) {
+		dev_err(dev, "Failed to get clk CGU iomem\n");
 		return PTR_ERR(ctx->membase);
+	}
+
 
 	ctx->np = np;
 	ctx->dev = dev;
-	spin_lock_init(&ctx->lock);
 
 	ret = lgm_clk_register_plls(ctx, lgm_pll_clks,
 				    ARRAY_SIZE(lgm_pll_clks));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/xilinx/xlnx_vcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/xilinx/xlnx_vcu.c
@@ -11,6 +11,7 @@
 #include <linux/clk-provider.h>
 #include <linux/device.h>
 #include <linux/errno.h>
+#include <linux/gpio/consumer.h>
 #include <linux/io.h>
 #include <linux/mfd/syscon.h>
 #include <linux/mfd/syscon/xlnx-vcu.h>
@@ -46,28 +47,6 @@
 #define FVCO_MIN			(1500U * MHZ)
 #define FVCO_MAX			(3000U * MHZ)
 
-/**
- * struct xvcu_device - Xilinx VCU init device structure
- * @dev: Platform device
- * @pll_ref: pll ref clock source
- * @aclk: axi clock source
- * @logicore_reg_ba: logicore reg base address
- * @vcu_slcr_ba: vcu_slcr Register base address
- * @pll: handle for the VCU PLL
- * @pll_post: handle for the VCU PLL post divider
- * @clk_data: clocks provided by the vcu clock provider
- */
-struct xvcu_device {
-	struct device *dev;
-	struct clk *pll_ref;
-	struct clk *aclk;
-	struct regmap *logicore_reg_ba;
-	void __iomem *vcu_slcr_ba;
-	struct clk_hw *pll;
-	struct clk_hw *pll_post;
-	struct clk_hw_onecell_data *clk_data;
-};
-
 static struct regmap_config vcu_settings_regmap_config = {
 	.name = "regmap",
 	.reg_bits = 32,
@@ -223,6 +202,78 @@
 	iowrite32(value, iomem + offset);
 }
 
+/**
+ * xvcu_get_color_depth - read the color depth register
+ * @xvcu:	Pointer to the xvcu_device structure
+ *
+ * Return:	Returns 32bit value
+ *
+ */
+u32 xvcu_get_color_depth(struct xvcu_device *xvcu)
+{
+	u32 value;
+
+	if (!regmap_read(xvcu->logicore_reg_ba, VCU_ENC_COLOR_DEPTH, &value))
+		return value;
+	else
+		return 0;
+}
+EXPORT_SYMBOL_GPL(xvcu_get_color_depth);
+
+/**
+ * xvcu_get_memory_depth - read the memory depth register
+ * @xvcu:	Pointer to the xvcu_device structure
+ *
+ * Return:	Returns 32bit value
+ *
+ */
+u32 xvcu_get_memory_depth(struct xvcu_device *xvcu)
+{
+	u32 value;
+
+	if (!regmap_read(xvcu->logicore_reg_ba, VCU_MEMORY_DEPTH, &value))
+		return value;
+	else
+		return 0;
+}
+EXPORT_SYMBOL_GPL(xvcu_get_memory_depth);
+
+/**
+ * xvcu_get_clock_frequency - provide the core clock frequency
+ * @xvcu:	Pointer to the xvcu_device structure
+ *
+ * Return:	Returns 32bit value
+ *
+ */
+u32 xvcu_get_clock_frequency(struct xvcu_device *xvcu)
+{
+	u32 value;
+
+	if (!regmap_read(xvcu->logicore_reg_ba, VCU_CORE_CLK, &value))
+		return value * MHZ;
+	else
+		return 0;
+}
+EXPORT_SYMBOL_GPL(xvcu_get_clock_frequency);
+
+/**
+ * xvcu_get_num_cores - read the number of core register
+ * @xvcu:	Pointer to the xvcu_device structure
+ *
+ * Return:	Returns 32bit value
+ *
+ */
+u32 xvcu_get_num_cores(struct xvcu_device *xvcu)
+{
+	u32 value;
+
+	if (!regmap_read(xvcu->logicore_reg_ba, VCU_NUM_CORE, &value))
+		return value;
+	else
+		return 0;
+}
+EXPORT_SYMBOL_GPL(xvcu_get_num_cores);
+
 #define to_vcu_pll(_hw) container_of(_hw, struct vcu_pll, hw)
 
 struct vcu_pll {
@@ -547,7 +598,7 @@
 		return PTR_ERR(hw);
 	xvcu->pll_post = hw;
 
-	parent_data[0].fw_name = "pll_ref";
+	parent_data[0].fw_name = "dummy_name";
 	parent_data[1].hw = xvcu->pll_post;
 
 	hws[CLK_XVCU_ENC_CORE] =
@@ -676,6 +727,24 @@
 	 * Bit 0 : Gasket isolation
 	 * Bit 1 : put VCU out of reset
 	 */
+	xvcu->reset_gpio = devm_gpiod_get_optional(&pdev->dev, "reset",
+						   GPIOD_OUT_LOW);
+	if (IS_ERR(xvcu->reset_gpio)) {
+		ret = PTR_ERR(xvcu->reset_gpio);
+		dev_err(&pdev->dev, "failed to get reset gpio for vcu.\n");
+		goto error_get_gpio;
+	}
+
+	if (xvcu->reset_gpio) {
+		gpiod_set_value(xvcu->reset_gpio, 0);
+		/* min 2 clock cycle of vcu pll_ref, slowest freq is 33.33KHz */
+		usleep_range(60, 120);
+		gpiod_set_value(xvcu->reset_gpio, 1);
+		usleep_range(60, 120);
+	} else {
+		dev_warn(&pdev->dev, "No reset gpio info from dts for vcu. This may lead to incorrect functionality if VCU isolation is removed post initialization.\n");
+	}
+
 	regmap_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, VCU_GASKET_VALUE);
 
 	ret = xvcu_register_clock_provider(xvcu);
@@ -686,10 +755,17 @@
 
 	dev_set_drvdata(&pdev->dev, xvcu);
 
+	ret = devm_of_platform_populate(&pdev->dev);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to register allegro codecs\n");
+		goto error_clk_provider;
+	}
+
 	return 0;
 
 error_clk_provider:
 	xvcu_unregister_clock_provider(xvcu);
+error_get_gpio:
 	clk_disable_unprepare(xvcu->aclk);
 	return ret;
 }
@@ -713,6 +789,13 @@
 	xvcu_unregister_clock_provider(xvcu);
 
 	/* Add the Gasket isolation and put the VCU in reset. */
+	if (xvcu->reset_gpio) {
+		gpiod_set_value(xvcu->reset_gpio, 0);
+		/* min 2 clock cycle of vcu pll_ref, slowest freq is 33.33KHz */
+		usleep_range(60, 120);
+		gpiod_set_value(xvcu->reset_gpio, 1);
+		usleep_range(60, 120);
+	}
 	regmap_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, 0);
 
 	clk_disable_unprepare(xvcu->aclk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/zynq/clkc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/zynq/clkc.c
@@ -37,11 +37,13 @@
 #define SLCR_CAN_MIOCLK_CTRL		(zynq_clkc_base + 0x60)
 #define SLCR_DBG_CLK_CTRL		(zynq_clkc_base + 0x64)
 #define SLCR_PCAP_CLK_CTRL		(zynq_clkc_base + 0x68)
+#define SLCR_TOPSW_CLK_CTRL		(zynq_clkc_base + 0x6c)
 #define SLCR_FPGA0_CLK_CTRL		(zynq_clkc_base + 0x70)
 #define SLCR_621_TRUE			(zynq_clkc_base + 0xc4)
 #define SLCR_SWDT_CLK_SEL		(zynq_clkc_base + 0x204)
 
 #define NUM_MIO_PINS	54
+#define CLK_NAME_LEN	16
 
 #define DBG_CLK_CTRL_CLKACT_TRC		BIT(0)
 #define DBG_CLK_CTRL_CPU_1XCLKACT	BIT(1)
@@ -99,6 +101,48 @@
 static const char *const swdt_ext_clk_input_names[] __initconst = {
 	"swdt_ext_clk"};
 
+#ifdef CONFIG_SUSPEND
+static struct clk *iopll_save_parent;
+
+#define TOPSW_CLK_CTRL_DIS_MASK	BIT(0)
+
+int zynq_clk_suspend_early(void)
+{
+	int ret;
+
+	iopll_save_parent = clk_get_parent(clks[iopll]);
+
+	ret = clk_set_parent(clks[iopll], ps_clk);
+	if (ret)
+		pr_info("%s: reparent iopll failed %d\n", __func__, ret);
+
+	return 0;
+}
+
+void zynq_clk_resume_late(void)
+{
+	clk_set_parent(clks[iopll], iopll_save_parent);
+}
+
+void zynq_clk_topswitch_enable(void)
+{
+	u32 reg;
+
+	reg = readl(SLCR_TOPSW_CLK_CTRL);
+	reg &= ~TOPSW_CLK_CTRL_DIS_MASK;
+	writel(reg, SLCR_TOPSW_CLK_CTRL);
+}
+
+void zynq_clk_topswitch_disable(void)
+{
+	u32 reg;
+
+	reg = readl(SLCR_TOPSW_CLK_CTRL);
+	reg |= TOPSW_CLK_CTRL_DIS_MASK;
+	writel(reg, SLCR_TOPSW_CLK_CTRL);
+}
+#endif
+
 static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
 		const char *clk_name, void __iomem *fclk_ctrl_reg,
 		const char **parents, int enable)
@@ -215,7 +259,7 @@
 	int i;
 	u32 tmp;
 	int ret;
-	char *clk_name;
+	char clk_name[CLK_NAME_LEN];
 	unsigned int fclk_enable = 0;
 	const char *clk_output_name[clk_max];
 	const char *cpu_parents[4];
@@ -349,19 +393,20 @@
 	/* Peripheral clocks */
 	for (i = fclk0; i <= fclk3; i++) {
 		int enable = !!(fclk_enable & BIT(i - fclk0));
+
 		zynq_clk_register_fclk(i, clk_output_name[i],
 				SLCR_FPGA0_CLK_CTRL + 0x10 * (i - fclk0),
 				periph_parents, enable);
 	}
 
-	zynq_clk_register_periph_clk(lqspi, 0, clk_output_name[lqspi], NULL,
-			SLCR_LQSPI_CLK_CTRL, periph_parents, 0);
+	zynq_clk_register_periph_clk(lqspi, clk_max, clk_output_name[lqspi], NULL,
+				     SLCR_LQSPI_CLK_CTRL, periph_parents, 0);
 
-	zynq_clk_register_periph_clk(smc, 0, clk_output_name[smc], NULL,
-			SLCR_SMC_CLK_CTRL, periph_parents, 0);
+	zynq_clk_register_periph_clk(smc, clk_max, clk_output_name[smc], NULL,
+				     SLCR_SMC_CLK_CTRL, periph_parents, 0);
 
-	zynq_clk_register_periph_clk(pcap, 0, clk_output_name[pcap], NULL,
-			SLCR_PCAP_CLK_CTRL, periph_parents, 0);
+	zynq_clk_register_periph_clk(pcap, clk_max, clk_output_name[pcap], NULL,
+				     SLCR_PCAP_CLK_CTRL, periph_parents, 0);
 
 	zynq_clk_register_periph_clk(sdio0, sdio1, clk_output_name[sdio0],
 			clk_output_name[sdio1], SLCR_SDIO_CLK_CTRL,
@@ -425,12 +470,10 @@
 			"gem1_emio_mux", CLK_SET_RATE_PARENT,
 			SLCR_GEM1_CLK_CTRL, 0, 0, &gem1clk_lock);
 
-	tmp = strlen("mio_clk_00x");
-	clk_name = kmalloc(tmp, GFP_KERNEL);
 	for (i = 0; i < NUM_MIO_PINS; i++) {
 		int idx;
 
-		snprintf(clk_name, tmp, "mio_clk_%2.2d", i);
+		snprintf(clk_name, CLK_NAME_LEN, "mio_clk_%2.2d", i);
 		idx = of_property_match_string(np, "clock-names", clk_name);
 		if (idx >= 0)
 			can_mio_mux_parents[i] = of_clk_get_parent_name(np,
@@ -438,7 +481,6 @@
 		else
 			can_mio_mux_parents[i] = dummy_nm;
 	}
-	kfree(clk_name);
 	clk_register_mux(NULL, "can_mux", periph_parents, 4,
 			CLK_SET_RATE_NO_REPARENT, SLCR_CAN_CLK_CTRL, 4, 2, 0,
 			&canclk_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/zynq/pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/zynq/pll.c
@@ -12,7 +12,7 @@
 #include <linux/io.h>
 
 /**
- * struct zynq_pll
+ * struct zynq_pll - pll clock
  * @hw:		Handle between common and hardware-specific interfaces
  * @pll_ctrl:	PLL control register
  * @pll_status:	PLL status register
@@ -46,7 +46,7 @@
  * @hw:		Handle between common and hardware-specific interfaces
  * @rate:	Desired clock frequency
  * @prate:	Clock frequency of parent clock
- * Returns frequency closest to @rate the hardware can generate.
+ * Return:	frequency closest to @rate the hardware can generate.
  */
 static long zynq_pll_round_rate(struct clk_hw *hw, unsigned long rate,
 		unsigned long *prate)
@@ -66,7 +66,7 @@
  * zynq_pll_recalc_rate() - Recalculate clock frequency
  * @hw:			Handle between common and hardware-specific interfaces
  * @parent_rate:	Clock frequency of parent clock
- * Returns current clock frequency.
+ * Return:		current clock frequency.
  */
 static unsigned long zynq_pll_recalc_rate(struct clk_hw *hw,
 		unsigned long parent_rate)
@@ -87,7 +87,7 @@
 /**
  * zynq_pll_is_enabled - Check if a clock is enabled
  * @hw:		Handle between common and hardware-specific interfaces
- * Returns 1 if the clock is enabled, 0 otherwise.
+ * Return:	1 if the clock is enabled, 0 otherwise.
  *
  * Not sure this is a good idea, but since disabled means bypassed for
  * this clock implementation we say we are always enabled.
@@ -110,7 +110,7 @@
 /**
  * zynq_pll_enable - Enable clock
  * @hw:		Handle between common and hardware-specific interfaces
- * Returns 0 on success
+ * Return: 0 on success
  */
 static int zynq_pll_enable(struct clk_hw *hw)
 {
@@ -179,7 +179,7 @@
  * @pll_status:	Pointer to PLL status register
  * @lock_index:	Bit index to this PLL's lock status bit in @pll_status
  * @lock:	Register lock
- * Returns handle to the registered clock.
+ * Return:	handle to the registered clock.
  */
 struct clk *clk_register_zynq_pll(const char *name, const char *parent,
 		void __iomem *pll_ctrl, void __iomem *pll_status, u8 lock_index,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/zynqmp/clk-mux-zynqmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/zynqmp/clk-mux-zynqmp.c
@@ -89,7 +89,7 @@
 static const struct clk_ops zynqmp_clk_mux_ops = {
 	.get_parent = zynqmp_clk_mux_get_parent,
 	.set_parent = zynqmp_clk_mux_set_parent,
-	.determine_rate = __clk_mux_determine_rate,
+	.determine_rate = __clk_mux_determine_rate_closest,
 };
 
 static const struct clk_ops zynqmp_clk_mux_ro_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/zynqmp/clkc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/zynqmp/clkc.c
@@ -710,6 +710,13 @@
 				  FIELD_PREP(CLK_ATTR_NODE_INDEX, i);
 
 		zynqmp_pm_clock_get_name(clock[i].clk_id, &name);
+
+		/*
+		 * Terminate with NULL character in case name provided by firmware
+		 * is longer and truncated due to size limit.
+		 */
+		name.name[sizeof(name.name) - 1] = '\0';
+
 		if (!strcmp(name.name, RESERVED_CLK_NAME))
 			continue;
 		strncpy(clock[i].clk_name, name.name, MAX_NAME_LEN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/zynqmp/divider.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/zynqmp/divider.c
@@ -113,17 +113,20 @@
 static void zynqmp_get_divider2_val(struct clk_hw *hw,
 				    unsigned long rate,
 				    struct zynqmp_clk_divider *divider,
-				    int *bestdiv)
+				    u32 *bestdiv)
 {
 	int div1;
 	int div2;
 	long error = LONG_MAX;
 	unsigned long div1_prate;
 	struct clk_hw *div1_parent_hw;
+	struct zynqmp_clk_divider *pdivider;
 	struct clk_hw *div2_parent_hw = clk_hw_get_parent(hw);
-	struct zynqmp_clk_divider *pdivider =
-				to_zynqmp_clk_divider(div2_parent_hw);
 
+	if (!div2_parent_hw)
+		return;
+
+	pdivider = to_zynqmp_clk_divider(div2_parent_hw);
 	if (!pdivider)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clk/zynqmp/pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clk/zynqmp/pll.c
@@ -102,26 +102,25 @@
 				  unsigned long *prate)
 {
 	u32 fbdiv;
-	long rate_div, f;
+	u32 mult, div;
 
-	/* Enable the fractional mode if needed */
-	rate_div = (rate * FRAC_DIV) / *prate;
-	f = rate_div % FRAC_DIV;
-	if (f) {
-		if (rate > PS_PLL_VCO_MAX) {
-			fbdiv = rate / PS_PLL_VCO_MAX;
-			rate = rate / (fbdiv + 1);
-		}
-		if (rate < PS_PLL_VCO_MIN) {
-			fbdiv = DIV_ROUND_UP(PS_PLL_VCO_MIN, rate);
-			rate = rate * fbdiv;
-		}
-		return rate;
+	/* Let rate fall inside the range PS_PLL_VCO_MIN ~ PS_PLL_VCO_MAX */
+	if (rate > PS_PLL_VCO_MAX) {
+		div = DIV_ROUND_UP(rate, PS_PLL_VCO_MAX);
+		rate = rate / div;
+	}
+	if (rate < PS_PLL_VCO_MIN) {
+		mult = DIV_ROUND_UP(PS_PLL_VCO_MIN, rate);
+		rate = rate * mult;
 	}
 
 	fbdiv = DIV_ROUND_CLOSEST(rate, *prate);
-	fbdiv = clamp_t(u32, fbdiv, PLL_FBDIV_MIN, PLL_FBDIV_MAX);
-	return *prate * fbdiv;
+	if (fbdiv < PLL_FBDIV_MIN || fbdiv > PLL_FBDIV_MAX) {
+		fbdiv = clamp_t(u32, fbdiv, PLL_FBDIV_MIN, PLL_FBDIV_MAX);
+		rate = *prate * fbdiv;
+	}
+
+	return rate;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/Kconfig
@@ -24,6 +24,7 @@
 
 config OMAP_DM_TIMER
 	bool
+	select TIMER_OF
 
 config CLKBLD_I8253
 	def_bool y if CLKSRC_I8253 || CLKEVT_I8253 || I8253_LOCK
@@ -374,7 +375,8 @@
 	  This affects CPU_FREQ max delta from the initial frequency.
 
 config ARM_TIMER_SP804
-	bool "Support for Dual Timer SP804 module" if COMPILE_TEST
+	bool "Support for Dual Timer SP804 module"
+	depends on ARM || ARM64 || COMPILE_TEST
 	depends on GENERIC_SCHED_CLOCK && HAVE_CLK
 	select CLKSRC_MMIO
 	select TIMER_OF if OF
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/acpi_pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/acpi_pm.c
@@ -229,8 +229,10 @@
 	int ret;
 
 	ret = kstrtouint(arg, 16, &base);
-	if (ret)
-		return ret;
+	if (ret) {
+		pr_warn("PMTMR: invalid 'pmtmr=' value: '%s'\n", arg);
+		return 1;
+	}
 
 	pr_info("PMTMR IOPort override: 0x%04x -> 0x%04x\n", pmtmr_ioport,
 		base);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/arm_arch_timer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/arm_arch_timer.c
@@ -44,23 +44,29 @@
 #define CNTACR_RWVT	BIT(4)
 #define CNTACR_RWPT	BIT(5)
 
-#define CNTVCT_LO	0x08
-#define CNTVCT_HI	0x0c
+#define CNTVCT_LO	0x00
+#define CNTPCT_LO	0x08
 #define CNTFRQ		0x10
-#define CNTP_TVAL	0x28
+#define CNTP_CVAL_LO	0x20
 #define CNTP_CTL	0x2c
-#define CNTV_TVAL	0x38
+#define CNTV_CVAL_LO	0x30
 #define CNTV_CTL	0x3c
 
-static unsigned arch_timers_present __initdata;
+/*
+ * The minimum amount of time a generic counter is guaranteed to not roll over
+ * (40 years)
+ */
+#define MIN_ROLLOVER_SECS	(40ULL * 365 * 24 * 3600)
 
-static void __iomem *arch_counter_base __ro_after_init;
+static unsigned arch_timers_present __initdata;
 
 struct arch_timer {
 	void __iomem *base;
 	struct clock_event_device evt;
 };
 
+static struct arch_timer *arch_timer_mem __ro_after_init;
+
 #define to_arch_timer(e) container_of(e, struct arch_timer, evt)
 
 static u32 arch_timer_rate __ro_after_init;
@@ -96,32 +102,57 @@
 early_param("clocksource.arm_arch_timer.evtstrm", early_evtstrm_cfg);
 
 /*
+ * Makes an educated guess at a valid counter width based on the Generic Timer
+ * specification. Of note:
+ *   1) the system counter is at least 56 bits wide
+ *   2) a roll-over time of not less than 40 years
+ *
+ * See 'ARM DDI 0487G.a D11.1.2 ("The system counter")' for more details.
+ */
+static int arch_counter_get_width(void)
+{
+	u64 min_cycles = MIN_ROLLOVER_SECS * arch_timer_rate;
+
+	/* guarantee the returned width is within the valid range */
+	return clamp_val(ilog2(min_cycles - 1) + 1, 56, 64);
+}
+
+/*
  * Architected system timer support.
  */
 
 static __always_inline
-void arch_timer_reg_write(int access, enum arch_timer_reg reg, u32 val,
+void arch_timer_reg_write(int access, enum arch_timer_reg reg, u64 val,
 			  struct clock_event_device *clk)
 {
 	if (access == ARCH_TIMER_MEM_PHYS_ACCESS) {
 		struct arch_timer *timer = to_arch_timer(clk);
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
-			writel_relaxed(val, timer->base + CNTP_CTL);
+			writel_relaxed((u32)val, timer->base + CNTP_CTL);
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			writel_relaxed(val, timer->base + CNTP_TVAL);
+		case ARCH_TIMER_REG_CVAL:
+			/*
+			 * Not guaranteed to be atomic, so the timer
+			 * must be disabled at this point.
+			 */
+			writeq_relaxed(val, timer->base + CNTP_CVAL_LO);
 			break;
+		default:
+			BUILD_BUG();
 		}
 	} else if (access == ARCH_TIMER_MEM_VIRT_ACCESS) {
 		struct arch_timer *timer = to_arch_timer(clk);
 		switch (reg) {
 		case ARCH_TIMER_REG_CTRL:
-			writel_relaxed(val, timer->base + CNTV_CTL);
+			writel_relaxed((u32)val, timer->base + CNTV_CTL);
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			writel_relaxed(val, timer->base + CNTV_TVAL);
+		case ARCH_TIMER_REG_CVAL:
+			/* Same restriction as above */
+			writeq_relaxed(val, timer->base + CNTV_CVAL_LO);
 			break;
+		default:
+			BUILD_BUG();
 		}
 	} else {
 		arch_timer_reg_write_cp15(access, reg, val);
@@ -140,9 +171,8 @@
 		case ARCH_TIMER_REG_CTRL:
 			val = readl_relaxed(timer->base + CNTP_CTL);
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			val = readl_relaxed(timer->base + CNTP_TVAL);
-			break;
+		default:
+			BUILD_BUG();
 		}
 	} else if (access == ARCH_TIMER_MEM_VIRT_ACCESS) {
 		struct arch_timer *timer = to_arch_timer(clk);
@@ -150,9 +180,8 @@
 		case ARCH_TIMER_REG_CTRL:
 			val = readl_relaxed(timer->base + CNTV_CTL);
 			break;
-		case ARCH_TIMER_REG_TVAL:
-			val = readl_relaxed(timer->base + CNTV_TVAL);
-			break;
+		default:
+			BUILD_BUG();
 		}
 	} else {
 		val = arch_timer_reg_read_cp15(access, reg);
@@ -205,13 +234,11 @@
 	.id	= CSID_ARM_ARCH_COUNTER,
 	.rating	= 400,
 	.read	= arch_counter_read,
-	.mask	= CLOCKSOURCE_MASK(56),
 	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
 static struct cyclecounter cyclecounter __ro_after_init = {
 	.read	= arch_counter_read_cc,
-	.mask	= CLOCKSOURCE_MASK(56),
 };
 
 struct ate_acpi_oem_info {
@@ -239,16 +266,6 @@
 	_new;						\
 })
 
-static u32 notrace fsl_a008585_read_cntp_tval_el0(void)
-{
-	return __fsl_a008585_read_reg(cntp_tval_el0);
-}
-
-static u32 notrace fsl_a008585_read_cntv_tval_el0(void)
-{
-	return __fsl_a008585_read_reg(cntv_tval_el0);
-}
-
 static u64 notrace fsl_a008585_read_cntpct_el0(void)
 {
 	return __fsl_a008585_read_reg(cntpct_el0);
@@ -285,16 +302,6 @@
 	_new;							\
 })
 
-static u32 notrace hisi_161010101_read_cntp_tval_el0(void)
-{
-	return __hisi_161010101_read_reg(cntp_tval_el0);
-}
-
-static u32 notrace hisi_161010101_read_cntv_tval_el0(void)
-{
-	return __hisi_161010101_read_reg(cntv_tval_el0);
-}
-
 static u64 notrace hisi_161010101_read_cntpct_el0(void)
 {
 	return __hisi_161010101_read_reg(cntpct_el0);
@@ -379,16 +386,6 @@
 {
 	return __sun50i_a64_read_reg(cntvct_el0);
 }
-
-static u32 notrace sun50i_a64_read_cntp_tval_el0(void)
-{
-	return read_sysreg(cntp_cval_el0) - sun50i_a64_read_cntpct_el0();
-}
-
-static u32 notrace sun50i_a64_read_cntv_tval_el0(void)
-{
-	return read_sysreg(cntv_cval_el0) - sun50i_a64_read_cntvct_el0();
-}
 #endif
 
 #ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
@@ -397,7 +394,7 @@
 
 static atomic_t timer_unstable_counter_workaround_in_use = ATOMIC_INIT(0);
 
-static void erratum_set_next_event_tval_generic(const int access, unsigned long evt,
+static void erratum_set_next_event_generic(const int access, unsigned long evt,
 						struct clock_event_device *clk)
 {
 	unsigned long ctrl;
@@ -418,17 +415,17 @@
 	arch_timer_reg_write(access, ARCH_TIMER_REG_CTRL, ctrl, clk);
 }
 
-static __maybe_unused int erratum_set_next_event_tval_virt(unsigned long evt,
+static __maybe_unused int erratum_set_next_event_virt(unsigned long evt,
 					    struct clock_event_device *clk)
 {
-	erratum_set_next_event_tval_generic(ARCH_TIMER_VIRT_ACCESS, evt, clk);
+	erratum_set_next_event_generic(ARCH_TIMER_VIRT_ACCESS, evt, clk);
 	return 0;
 }
 
-static __maybe_unused int erratum_set_next_event_tval_phys(unsigned long evt,
+static __maybe_unused int erratum_set_next_event_phys(unsigned long evt,
 					    struct clock_event_device *clk)
 {
-	erratum_set_next_event_tval_generic(ARCH_TIMER_PHYS_ACCESS, evt, clk);
+	erratum_set_next_event_generic(ARCH_TIMER_PHYS_ACCESS, evt, clk);
 	return 0;
 }
 
@@ -438,12 +435,10 @@
 		.match_type = ate_match_dt,
 		.id = "fsl,erratum-a008585",
 		.desc = "Freescale erratum a005858",
-		.read_cntp_tval_el0 = fsl_a008585_read_cntp_tval_el0,
-		.read_cntv_tval_el0 = fsl_a008585_read_cntv_tval_el0,
 		.read_cntpct_el0 = fsl_a008585_read_cntpct_el0,
 		.read_cntvct_el0 = fsl_a008585_read_cntvct_el0,
-		.set_next_event_phys = erratum_set_next_event_tval_phys,
-		.set_next_event_virt = erratum_set_next_event_tval_virt,
+		.set_next_event_phys = erratum_set_next_event_phys,
+		.set_next_event_virt = erratum_set_next_event_virt,
 	},
 #endif
 #ifdef CONFIG_HISILICON_ERRATUM_161010101
@@ -451,23 +446,19 @@
 		.match_type = ate_match_dt,
 		.id = "hisilicon,erratum-161010101",
 		.desc = "HiSilicon erratum 161010101",
-		.read_cntp_tval_el0 = hisi_161010101_read_cntp_tval_el0,
-		.read_cntv_tval_el0 = hisi_161010101_read_cntv_tval_el0,
 		.read_cntpct_el0 = hisi_161010101_read_cntpct_el0,
 		.read_cntvct_el0 = hisi_161010101_read_cntvct_el0,
-		.set_next_event_phys = erratum_set_next_event_tval_phys,
-		.set_next_event_virt = erratum_set_next_event_tval_virt,
+		.set_next_event_phys = erratum_set_next_event_phys,
+		.set_next_event_virt = erratum_set_next_event_virt,
 	},
 	{
 		.match_type = ate_match_acpi_oem_info,
 		.id = hisi_161010101_oem_info,
 		.desc = "HiSilicon erratum 161010101",
-		.read_cntp_tval_el0 = hisi_161010101_read_cntp_tval_el0,
-		.read_cntv_tval_el0 = hisi_161010101_read_cntv_tval_el0,
 		.read_cntpct_el0 = hisi_161010101_read_cntpct_el0,
 		.read_cntvct_el0 = hisi_161010101_read_cntvct_el0,
-		.set_next_event_phys = erratum_set_next_event_tval_phys,
-		.set_next_event_virt = erratum_set_next_event_tval_virt,
+		.set_next_event_phys = erratum_set_next_event_phys,
+		.set_next_event_virt = erratum_set_next_event_virt,
 	},
 #endif
 #ifdef CONFIG_ARM64_ERRATUM_858921
@@ -484,12 +475,10 @@
 		.match_type = ate_match_dt,
 		.id = "allwinner,erratum-unknown1",
 		.desc = "Allwinner erratum UNKNOWN1",
-		.read_cntp_tval_el0 = sun50i_a64_read_cntp_tval_el0,
-		.read_cntv_tval_el0 = sun50i_a64_read_cntv_tval_el0,
 		.read_cntpct_el0 = sun50i_a64_read_cntpct_el0,
 		.read_cntvct_el0 = sun50i_a64_read_cntvct_el0,
-		.set_next_event_phys = erratum_set_next_event_tval_phys,
-		.set_next_event_virt = erratum_set_next_event_tval_virt,
+		.set_next_event_phys = erratum_set_next_event_phys,
+		.set_next_event_virt = erratum_set_next_event_virt,
 	},
 #endif
 #ifdef CONFIG_ARM64_ERRATUM_1418040
@@ -691,8 +680,8 @@
 	return timer_handler(ARCH_TIMER_MEM_VIRT_ACCESS, evt);
 }
 
-static __always_inline int timer_shutdown(const int access,
-					  struct clock_event_device *clk)
+static __always_inline int arch_timer_shutdown(const int access,
+					       struct clock_event_device *clk)
 {
 	unsigned long ctrl;
 
@@ -705,32 +694,40 @@
 
 static int arch_timer_shutdown_virt(struct clock_event_device *clk)
 {
-	return timer_shutdown(ARCH_TIMER_VIRT_ACCESS, clk);
+	return arch_timer_shutdown(ARCH_TIMER_VIRT_ACCESS, clk);
 }
 
 static int arch_timer_shutdown_phys(struct clock_event_device *clk)
 {
-	return timer_shutdown(ARCH_TIMER_PHYS_ACCESS, clk);
+	return arch_timer_shutdown(ARCH_TIMER_PHYS_ACCESS, clk);
 }
 
 static int arch_timer_shutdown_virt_mem(struct clock_event_device *clk)
 {
-	return timer_shutdown(ARCH_TIMER_MEM_VIRT_ACCESS, clk);
+	return arch_timer_shutdown(ARCH_TIMER_MEM_VIRT_ACCESS, clk);
 }
 
 static int arch_timer_shutdown_phys_mem(struct clock_event_device *clk)
 {
-	return timer_shutdown(ARCH_TIMER_MEM_PHYS_ACCESS, clk);
+	return arch_timer_shutdown(ARCH_TIMER_MEM_PHYS_ACCESS, clk);
 }
 
 static __always_inline void set_next_event(const int access, unsigned long evt,
 					   struct clock_event_device *clk)
 {
 	unsigned long ctrl;
+	u64 cnt;
+
 	ctrl = arch_timer_reg_read(access, ARCH_TIMER_REG_CTRL, clk);
 	ctrl |= ARCH_TIMER_CTRL_ENABLE;
 	ctrl &= ~ARCH_TIMER_CTRL_IT_MASK;
-	arch_timer_reg_write(access, ARCH_TIMER_REG_TVAL, evt, clk);
+
+	if (access == ARCH_TIMER_PHYS_ACCESS)
+		cnt = __arch_counter_get_cntpct();
+	else
+		cnt = __arch_counter_get_cntvct();
+
+	arch_timer_reg_write(access, ARCH_TIMER_REG_CVAL, evt + cnt, clk);
 	arch_timer_reg_write(access, ARCH_TIMER_REG_CTRL, ctrl, clk);
 }
 
@@ -748,23 +745,79 @@
 	return 0;
 }
 
+static u64 arch_counter_get_cnt_mem(struct arch_timer *t, int offset_lo)
+{
+	u32 cnt_lo, cnt_hi, tmp_hi;
+
+	do {
+		cnt_hi = readl_relaxed(t->base + offset_lo + 4);
+		cnt_lo = readl_relaxed(t->base + offset_lo);
+		tmp_hi = readl_relaxed(t->base + offset_lo + 4);
+	} while (cnt_hi != tmp_hi);
+
+	return ((u64) cnt_hi << 32) | cnt_lo;
+}
+
+static __always_inline void set_next_event_mem(const int access, unsigned long evt,
+					   struct clock_event_device *clk)
+{
+	struct arch_timer *timer = to_arch_timer(clk);
+	unsigned long ctrl;
+	u64 cnt;
+
+	ctrl = arch_timer_reg_read(access, ARCH_TIMER_REG_CTRL, clk);
+	ctrl |= ARCH_TIMER_CTRL_ENABLE;
+	ctrl &= ~ARCH_TIMER_CTRL_IT_MASK;
+
+	if (access ==  ARCH_TIMER_MEM_VIRT_ACCESS)
+		cnt = arch_counter_get_cnt_mem(timer, CNTVCT_LO);
+	else
+		cnt = arch_counter_get_cnt_mem(timer, CNTPCT_LO);
+
+	arch_timer_reg_write(access, ARCH_TIMER_REG_CVAL, evt + cnt, clk);
+	arch_timer_reg_write(access, ARCH_TIMER_REG_CTRL, ctrl, clk);
+}
+
 static int arch_timer_set_next_event_virt_mem(unsigned long evt,
 					      struct clock_event_device *clk)
 {
-	set_next_event(ARCH_TIMER_MEM_VIRT_ACCESS, evt, clk);
+	set_next_event_mem(ARCH_TIMER_MEM_VIRT_ACCESS, evt, clk);
 	return 0;
 }
 
 static int arch_timer_set_next_event_phys_mem(unsigned long evt,
 					      struct clock_event_device *clk)
 {
-	set_next_event(ARCH_TIMER_MEM_PHYS_ACCESS, evt, clk);
+	set_next_event_mem(ARCH_TIMER_MEM_PHYS_ACCESS, evt, clk);
 	return 0;
 }
 
+static u64 __arch_timer_check_delta(void)
+{
+#ifdef CONFIG_ARM64
+	const struct midr_range broken_cval_midrs[] = {
+		/*
+		 * XGene-1 implements CVAL in terms of TVAL, meaning
+		 * that the maximum timer range is 32bit. Shame on them.
+		 */
+		MIDR_ALL_VERSIONS(MIDR_CPU_MODEL(ARM_CPU_IMP_APM,
+						 APM_CPU_PART_POTENZA)),
+		{},
+	};
+
+	if (is_midr_in_range_list(read_cpuid_id(), broken_cval_midrs)) {
+		pr_warn_once("Broken CNTx_CVAL_EL1, limiting width to 32bits");
+		return CLOCKSOURCE_MASK(32);
+	}
+#endif
+	return CLOCKSOURCE_MASK(arch_counter_get_width());
+}
+
 static void __arch_timer_setup(unsigned type,
 			       struct clock_event_device *clk)
 {
+	u64 max_delta;
+
 	clk->features = CLOCK_EVT_FEAT_ONESHOT;
 
 	if (type == ARCH_TIMER_TYPE_CP15) {
@@ -796,6 +849,7 @@
 		}
 
 		clk->set_next_event = sne;
+		max_delta = __arch_timer_check_delta();
 	} else {
 		clk->features |= CLOCK_EVT_FEAT_DYNIRQ;
 		clk->name = "arch_mem_timer";
@@ -812,11 +866,13 @@
 			clk->set_next_event =
 				arch_timer_set_next_event_phys_mem;
 		}
+
+		max_delta = CLOCKSOURCE_MASK(56);
 	}
 
 	clk->set_state_shutdown(clk);
 
-	clockevents_config_and_register(clk, arch_timer_rate, 0xf, 0x7fffffff);
+	clockevents_config_and_register(clk, arch_timer_rate, 0xf, max_delta);
 }
 
 static void arch_timer_evtstrm_enable(int divider)
@@ -986,15 +1042,7 @@
 
 static u64 arch_counter_get_cntvct_mem(void)
 {
-	u32 vct_lo, vct_hi, tmp_hi;
-
-	do {
-		vct_hi = readl_relaxed(arch_counter_base + CNTVCT_HI);
-		vct_lo = readl_relaxed(arch_counter_base + CNTVCT_LO);
-		tmp_hi = readl_relaxed(arch_counter_base + CNTVCT_HI);
-	} while (vct_hi != tmp_hi);
-
-	return ((u64) vct_hi << 32) | vct_lo;
+	return arch_counter_get_cnt_mem(arch_timer_mem, CNTVCT_LO);
 }
 
 static struct arch_timer_kvm_info arch_timer_kvm_info;
@@ -1007,6 +1055,7 @@
 static void __init arch_counter_register(unsigned type)
 {
 	u64 start_count;
+	int width;
 
 	/* Register the CP15 based counter if we have one */
 	if (type & ARCH_TIMER_TYPE_CP15) {
@@ -1031,6 +1080,10 @@
 		arch_timer_read_counter = arch_counter_get_cntvct_mem;
 	}
 
+	width = arch_counter_get_width();
+	clocksource_counter.mask = CLOCKSOURCE_MASK(width);
+	cyclecounter.mask = CLOCKSOURCE_MASK(width);
+
 	if (!arch_counter_suspend_stop)
 		clocksource_counter.flags |= CLOCK_SOURCE_SUSPEND_NONSTOP;
 	start_count = arch_timer_read_counter();
@@ -1040,8 +1093,7 @@
 	timecounter_init(&arch_timer_kvm_info.timecounter,
 			 &cyclecounter, start_count);
 
-	/* 56 bits minimum, so we assume worst case rollover */
-	sched_clock_register(arch_timer_read_counter, 56, arch_timer_rate);
+	sched_clock_register(arch_timer_read_counter, width, arch_timer_rate);
 }
 
 static void arch_timer_stop(struct clock_event_device *clk)
@@ -1182,25 +1234,25 @@
 {
 	int ret;
 	irq_handler_t func;
-	struct arch_timer *t;
 
-	t = kzalloc(sizeof(*t), GFP_KERNEL);
-	if (!t)
+	arch_timer_mem = kzalloc(sizeof(*arch_timer_mem), GFP_KERNEL);
+	if (!arch_timer_mem)
 		return -ENOMEM;
 
-	t->base = base;
-	t->evt.irq = irq;
-	__arch_timer_setup(ARCH_TIMER_TYPE_MEM, &t->evt);
+	arch_timer_mem->base = base;
+	arch_timer_mem->evt.irq = irq;
+	__arch_timer_setup(ARCH_TIMER_TYPE_MEM, &arch_timer_mem->evt);
 
 	if (arch_timer_mem_use_virtual)
 		func = arch_timer_handler_virt_mem;
 	else
 		func = arch_timer_handler_phys_mem;
 
-	ret = request_irq(irq, func, IRQF_TIMER, "arch_mem_timer", &t->evt);
+	ret = request_irq(irq, func, IRQF_TIMER, "arch_mem_timer", &arch_timer_mem->evt);
 	if (ret) {
 		pr_err("Failed to request mem timer irq\n");
-		kfree(t);
+		kfree(arch_timer_mem);
+		arch_timer_mem = NULL;
 	}
 
 	return ret;
@@ -1458,7 +1510,6 @@
 		return ret;
 	}
 
-	arch_counter_base = base;
 	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/arm_global_timer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/arm_global_timer.c
@@ -32,7 +32,7 @@
 #define GT_CONTROL_IRQ_ENABLE		BIT(2)	/* banked */
 #define GT_CONTROL_AUTO_INC		BIT(3)	/* banked */
 #define GT_CONTROL_PRESCALER_SHIFT      8
-#define GT_CONTROL_PRESCALER_MAX        0xF
+#define GT_CONTROL_PRESCALER_MAX        0xFF
 #define GT_CONTROL_PRESCALER_MASK       (GT_CONTROL_PRESCALER_MAX << \
 					 GT_CONTROL_PRESCALER_SHIFT)
 
@@ -290,18 +290,17 @@
 	switch (event) {
 	case PRE_RATE_CHANGE:
 	{
-		int psv;
+		unsigned long psv;
 
-		psv = DIV_ROUND_CLOSEST(ndata->new_rate,
-					gt_target_rate);
-
-		if (abs(gt_target_rate - (ndata->new_rate / psv)) > MAX_F_ERR)
+		psv = DIV_ROUND_CLOSEST(ndata->new_rate, gt_target_rate);
+		if (!psv ||
+		    abs(gt_target_rate - (ndata->new_rate / psv)) > MAX_F_ERR)
 			return NOTIFY_BAD;
 
 		psv--;
 
 		/* prescaler within legal range? */
-		if (psv < 0 || psv > GT_CONTROL_PRESCALER_MAX)
+		if (psv > GT_CONTROL_PRESCALER_MAX)
 			return NOTIFY_BAD;
 
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/dw_apb_timer_of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/dw_apb_timer_of.c
@@ -47,7 +47,7 @@
 			pr_warn("pclk for %pOFn is present, but could not be activated\n",
 				np);
 
-	if (!of_property_read_u32(np, "clock-freq", rate) &&
+	if (!of_property_read_u32(np, "clock-freq", rate) ||
 	    !of_property_read_u32(np, "clock-frequency", rate))
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/exynos_mct.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/exynos_mct.c
@@ -504,11 +504,14 @@
 	return 0;
 }
 
-static int __init exynos4_timer_resources(struct device_node *np, void __iomem *base)
+static int __init exynos4_timer_resources(struct device_node *np)
 {
-	int err, cpu;
 	struct clk *mct_clk, *tick_clk;
 
+	reg_base = of_iomap(np, 0);
+	if (!reg_base)
+		panic("%s: unable to ioremap mct address space\n", __func__);
+
 	tick_clk = of_clk_get_by_name(np, "fin_pll");
 	if (IS_ERR(tick_clk))
 		panic("%s: unable to determine tick clock rate\n", __func__);
@@ -519,9 +522,32 @@
 		panic("%s: unable to retrieve mct clock instance\n", __func__);
 	clk_prepare_enable(mct_clk);
 
-	reg_base = base;
-	if (!reg_base)
-		panic("%s: unable to ioremap mct address space\n", __func__);
+	return 0;
+}
+
+static int __init exynos4_timer_interrupts(struct device_node *np,
+					   unsigned int int_type)
+{
+	int nr_irqs, i, err, cpu;
+
+	mct_int_type = int_type;
+
+	/* This driver uses only one global timer interrupt */
+	mct_irqs[MCT_G0_IRQ] = irq_of_parse_and_map(np, MCT_G0_IRQ);
+
+	/*
+	 * Find out the number of local irqs specified. The local
+	 * timer irqs are specified after the four global timer
+	 * irqs are specified.
+	 */
+	nr_irqs = of_irq_count(np);
+	if (nr_irqs > ARRAY_SIZE(mct_irqs)) {
+		pr_err("exynos-mct: too many (%d) interrupts configured in DT\n",
+			nr_irqs);
+		nr_irqs = ARRAY_SIZE(mct_irqs);
+	}
+	for (i = MCT_L0_IRQ; i < nr_irqs; i++)
+		mct_irqs[i] = irq_of_parse_and_map(np, i);
 
 	if (mct_int_type == MCT_INT_PPI) {
 
@@ -532,11 +558,14 @@
 		     mct_irqs[MCT_L0_IRQ], err);
 	} else {
 		for_each_possible_cpu(cpu) {
-			int mct_irq = mct_irqs[MCT_L0_IRQ + cpu];
+			int mct_irq;
 			struct mct_clock_event_device *pcpu_mevt =
 				per_cpu_ptr(&percpu_mct_tick, cpu);
 
 			pcpu_mevt->evt.irq = -1;
+			if (MCT_L0_IRQ + cpu >= ARRAY_SIZE(mct_irqs))
+				break;
+			mct_irq = mct_irqs[MCT_L0_IRQ + cpu];
 
 			irq_set_status_flags(mct_irq, IRQ_NOAUTOEN);
 			if (request_irq(mct_irq,
@@ -581,24 +610,13 @@
 
 static int __init mct_init_dt(struct device_node *np, unsigned int int_type)
 {
-	u32 nr_irqs, i;
 	int ret;
 
-	mct_int_type = int_type;
-
-	/* This driver uses only one global timer interrupt */
-	mct_irqs[MCT_G0_IRQ] = irq_of_parse_and_map(np, MCT_G0_IRQ);
-
-	/*
-	 * Find out the number of local irqs specified. The local
-	 * timer irqs are specified after the four global timer
-	 * irqs are specified.
-	 */
-	nr_irqs = of_irq_count(np);
-	for (i = MCT_L0_IRQ; i < nr_irqs; i++)
-		mct_irqs[i] = irq_of_parse_and_map(np, i);
+	ret = exynos4_timer_resources(np);
+	if (ret)
+		return ret;
 
-	ret = exynos4_timer_resources(np, of_iomap(np, 0));
+	ret = exynos4_timer_interrupts(np, int_type);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/hyperv_timer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/hyperv_timer.c
@@ -26,7 +26,8 @@
 #include <asm/mshyperv.h>
 
 static struct clock_event_device __percpu *hv_clock_event;
-static u64 hv_sched_clock_offset __ro_after_init;
+/* Note: offset can hold negative values after hibernation. */
+static u64 hv_sched_clock_offset __read_mostly;
 
 /*
  * If false, we're using the old mechanism for stimer0 interrupts
@@ -416,6 +417,17 @@
 	hv_set_register(HV_REGISTER_REFERENCE_TSC, tsc_msr);
 }
 
+/*
+ * Called during resume from hibernation, from overridden
+ * x86_platform.restore_sched_clock_state routine. This is to adjust offsets
+ * used to calculate time for hv tsc page based sched_clock, to account for
+ * time spent before hibernation.
+ */
+void hv_adj_sched_clock_offset(u64 offset)
+{
+	hv_sched_clock_offset -= offset;
+}
+
 #ifdef HAVE_VDSO_CLOCKMODE_HVCLOCK
 static int hv_cs_enable(struct clocksource *cs)
 {
@@ -565,4 +577,3 @@
 	hv_sched_clock_offset = hv_read_reference_counter();
 	hv_setup_sched_clock(read_hv_sched_clock_msr);
 }
-EXPORT_SYMBOL_GPL(hv_init_clocksource);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/i8253.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/i8253.c
@@ -20,13 +20,6 @@
 DEFINE_RAW_SPINLOCK(i8253_lock);
 EXPORT_SYMBOL(i8253_lock);
 
-/*
- * Handle PIT quirk in pit_shutdown() where zeroing the counter register
- * restarts the PIT, negating the shutdown. On platforms with the quirk,
- * platform specific code can set this to false.
- */
-bool i8253_clear_counter_on_shutdown __ro_after_init = true;
-
 #ifdef CONFIG_CLKSRC_I8253
 /*
  * Since the PIT overflows every tick, its not very useful
@@ -108,21 +101,47 @@
 #endif
 
 #ifdef CONFIG_CLKEVT_I8253
-static int pit_shutdown(struct clock_event_device *evt)
+void clockevent_i8253_disable(void)
 {
-	if (!clockevent_state_oneshot(evt) && !clockevent_state_periodic(evt))
-		return 0;
-
 	raw_spin_lock(&i8253_lock);
 
+	/*
+	 * Writing the MODE register should stop the counter, according to
+	 * the datasheet. This appears to work on real hardware (well, on
+	 * modern Intel and AMD boxes; I didn't dig the Pegasos out of the
+	 * shed).
+	 *
+	 * However, some virtual implementations differ, and the MODE change
+	 * doesn't have any effect until either the counter is written (KVM
+	 * in-kernel PIT) or the next interrupt (QEMU). And in those cases,
+	 * it may not stop the *count*, only the interrupts. Although in
+	 * the virt case, that probably doesn't matter, as the value of the
+	 * counter will only be calculated on demand if the guest reads it;
+	 * it's the interrupts which cause steal time.
+	 *
+	 * Hyper-V apparently has a bug where even in mode 0, the IRQ keeps
+	 * firing repeatedly if the counter is running. But it *does* do the
+	 * right thing when the MODE register is written.
+	 *
+	 * So: write the MODE and then load the counter, which ensures that
+	 * the IRQ is stopped on those buggy virt implementations. And then
+	 * write the MODE again, which is the right way to stop it.
+	 */
 	outb_p(0x30, PIT_MODE);
+	outb_p(0, PIT_CH0);
+	outb_p(0, PIT_CH0);
 
-	if (i8253_clear_counter_on_shutdown) {
-		outb_p(0, PIT_CH0);
-		outb_p(0, PIT_CH0);
-	}
+	outb_p(0x30, PIT_MODE);
 
 	raw_spin_unlock(&i8253_lock);
+}
+
+static int pit_shutdown(struct clock_event_device *evt)
+{
+	if (!clockevent_state_oneshot(evt) && !clockevent_state_periodic(evt))
+		return 0;
+
+	clockevent_i8253_disable();
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/sh_cmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/sh_cmt.c
@@ -13,6 +13,7 @@
 #include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/ioport.h>
 #include <linux/irq.h>
 #include <linux/module.h>
@@ -116,6 +117,7 @@
 	void __iomem *mapbase;
 	struct clk *clk;
 	unsigned long rate;
+	unsigned int reg_delay;
 
 	raw_spinlock_t lock; /* Protect the shared start/stop register */
 
@@ -247,10 +249,17 @@
 
 static inline void sh_cmt_write_cmstr(struct sh_cmt_channel *ch, u32 value)
 {
-	if (ch->iostart)
-		ch->cmt->info->write_control(ch->iostart, 0, value);
-	else
-		ch->cmt->info->write_control(ch->cmt->mapbase, 0, value);
+	u32 old_value = sh_cmt_read_cmstr(ch);
+
+	if (value != old_value) {
+		if (ch->iostart) {
+			ch->cmt->info->write_control(ch->iostart, 0, value);
+			udelay(ch->cmt->reg_delay);
+		} else {
+			ch->cmt->info->write_control(ch->cmt->mapbase, 0, value);
+			udelay(ch->cmt->reg_delay);
+		}
+	}
 }
 
 static inline u32 sh_cmt_read_cmcsr(struct sh_cmt_channel *ch)
@@ -260,7 +269,12 @@
 
 static inline void sh_cmt_write_cmcsr(struct sh_cmt_channel *ch, u32 value)
 {
-	ch->cmt->info->write_control(ch->ioctrl, CMCSR, value);
+	u32 old_value = sh_cmt_read_cmcsr(ch);
+
+	if (value != old_value) {
+		ch->cmt->info->write_control(ch->ioctrl, CMCSR, value);
+		udelay(ch->cmt->reg_delay);
+	}
 }
 
 static inline u32 sh_cmt_read_cmcnt(struct sh_cmt_channel *ch)
@@ -268,14 +282,33 @@
 	return ch->cmt->info->read_count(ch->ioctrl, CMCNT);
 }
 
-static inline void sh_cmt_write_cmcnt(struct sh_cmt_channel *ch, u32 value)
+static inline int sh_cmt_write_cmcnt(struct sh_cmt_channel *ch, u32 value)
 {
+	/* Tests showed that we need to wait 3 clocks here */
+	unsigned int cmcnt_delay = DIV_ROUND_UP(3 * ch->cmt->reg_delay, 2);
+	u32 reg;
+
+	if (ch->cmt->info->model > SH_CMT_16BIT) {
+		int ret = read_poll_timeout_atomic(sh_cmt_read_cmcsr, reg,
+						   !(reg & SH_CMT32_CMCSR_WRFLG),
+						   1, cmcnt_delay, false, ch);
+		if (ret < 0)
+			return ret;
+	}
+
 	ch->cmt->info->write_count(ch->ioctrl, CMCNT, value);
+	udelay(cmcnt_delay);
+	return 0;
 }
 
 static inline void sh_cmt_write_cmcor(struct sh_cmt_channel *ch, u32 value)
 {
-	ch->cmt->info->write_count(ch->ioctrl, CMCOR, value);
+	u32 old_value = ch->cmt->info->read_count(ch->ioctrl, CMCOR);
+
+	if (value != old_value) {
+		ch->cmt->info->write_count(ch->ioctrl, CMCOR, value);
+		udelay(ch->cmt->reg_delay);
+	}
 }
 
 static u32 sh_cmt_get_counter(struct sh_cmt_channel *ch, u32 *has_wrapped)
@@ -319,7 +352,7 @@
 
 static int sh_cmt_enable(struct sh_cmt_channel *ch)
 {
-	int k, ret;
+	int ret;
 
 	dev_pm_syscore_device(&ch->cmt->pdev->dev, true);
 
@@ -347,26 +380,9 @@
 	}
 
 	sh_cmt_write_cmcor(ch, 0xffffffff);
-	sh_cmt_write_cmcnt(ch, 0);
+	ret = sh_cmt_write_cmcnt(ch, 0);
 
-	/*
-	 * According to the sh73a0 user's manual, as CMCNT can be operated
-	 * only by the RCLK (Pseudo 32 kHz), there's one restriction on
-	 * modifying CMCNT register; two RCLK cycles are necessary before
-	 * this register is either read or any modification of the value
-	 * it holds is reflected in the LSI's actual operation.
-	 *
-	 * While at it, we're supposed to clear out the CMCNT as of this
-	 * moment, so make sure it's processed properly here.  This will
-	 * take RCLKx2 at maximum.
-	 */
-	for (k = 0; k < 100; k++) {
-		if (!sh_cmt_read_cmcnt(ch))
-			break;
-		udelay(1);
-	}
-
-	if (sh_cmt_read_cmcnt(ch)) {
+	if (ret || sh_cmt_read_cmcnt(ch)) {
 		dev_err(&ch->cmt->pdev->dev, "ch%u: cannot clear CMCNT\n",
 			ch->index);
 		ret = -ETIMEDOUT;
@@ -513,6 +529,7 @@
 static irqreturn_t sh_cmt_interrupt(int irq, void *dev_id)
 {
 	struct sh_cmt_channel *ch = dev_id;
+	unsigned long flags;
 
 	/* clear flags */
 	sh_cmt_write_cmcsr(ch, sh_cmt_read_cmcsr(ch) &
@@ -543,6 +560,8 @@
 
 	ch->flags &= ~FLAG_SKIPEVENT;
 
+	raw_spin_lock_irqsave(&ch->lock, flags);
+
 	if (ch->flags & FLAG_REPROGRAM) {
 		ch->flags &= ~FLAG_REPROGRAM;
 		sh_cmt_clock_event_program_verify(ch, 1);
@@ -555,6 +574,8 @@
 
 	ch->flags &= ~FLAG_IRQCONTEXT;
 
+	raw_spin_unlock_irqrestore(&ch->lock, flags);
+
 	return IRQ_HANDLED;
 }
 
@@ -765,12 +786,18 @@
 				   struct clock_event_device *ced)
 {
 	struct sh_cmt_channel *ch = ced_to_sh_cmt(ced);
+	unsigned long flags;
 
 	BUG_ON(!clockevent_state_oneshot(ced));
+
+	raw_spin_lock_irqsave(&ch->lock, flags);
+
 	if (likely(ch->flags & FLAG_IRQCONTEXT))
 		ch->next_match_value = delta - 1;
 	else
-		sh_cmt_set_next(ch, delta - 1);
+		__sh_cmt_set_next(ch, delta - 1);
+
+	raw_spin_unlock_irqrestore(&ch->lock, flags);
 
 	return 0;
 }
@@ -987,8 +1014,8 @@
 
 static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev)
 {
-	unsigned int mask;
-	unsigned int i;
+	unsigned int mask, i;
+	unsigned long rate;
 	int ret;
 
 	cmt->pdev = pdev;
@@ -1024,10 +1051,16 @@
 	if (ret < 0)
 		goto err_clk_unprepare;
 
-	if (cmt->info->width == 16)
-		cmt->rate = clk_get_rate(cmt->clk) / 512;
-	else
-		cmt->rate = clk_get_rate(cmt->clk) / 8;
+	rate = clk_get_rate(cmt->clk);
+	if (!rate) {
+		ret = -EINVAL;
+		goto err_clk_disable;
+	}
+
+	/* We shall wait 2 input clks after register writes */
+	if (cmt->info->model >= SH_CMT_48BIT)
+		cmt->reg_delay = DIV_ROUND_UP(2UL * USEC_PER_SEC, rate);
+	cmt->rate = rate / (cmt->info->width == 16 ? 512 : 8);
 
 	/* Map the memory resource(s). */
 	ret = sh_cmt_map_memory(cmt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-atmel-tcb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-atmel-tcb.c
@@ -315,6 +315,7 @@
 	writel(mck_divisor_idx			/* likely divide-by-8 */
 			| ATMEL_TC_WAVE
 			| ATMEL_TC_WAVESEL_UP		/* free-run */
+			| ATMEL_TC_ASWTRG_SET		/* TIOA0 rises at software trigger */
 			| ATMEL_TC_ACPA_SET		/* TIOA0 rises at 0 */
 			| ATMEL_TC_ACPC_CLEAR,		/* (duty cycle 50%) */
 			tcaddr + ATMEL_TC_REG(0, CMR));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-cadence-ttc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-cadence-ttc.c
@@ -476,6 +476,9 @@
 	u32 timer_width = 16;
 	struct device_node *timer = pdev->dev.of_node;
 
+	if (of_property_read_bool(timer, "#pwm-cells"))
+		return -ENODEV;
+
 	if (initialized)
 		return 0;
 
@@ -486,10 +489,10 @@
 	 * and use it. Note that the event timer uses the interrupt and it's the
 	 * 2nd TTC hence the irq_of_parse_and_map(,1)
 	 */
-	timer_baseaddr = of_iomap(timer, 0);
-	if (!timer_baseaddr) {
+	timer_baseaddr = devm_of_iomap(&pdev->dev, timer, 0, NULL);
+	if (IS_ERR(timer_baseaddr)) {
 		pr_err("ERROR: invalid timer base address\n");
-		return -ENXIO;
+		return PTR_ERR(timer_baseaddr);
 	}
 
 	irq = irq_of_parse_and_map(timer, 1);
@@ -513,20 +516,27 @@
 	clk_ce = of_clk_get(timer, clksel);
 	if (IS_ERR(clk_ce)) {
 		pr_err("ERROR: timer input clock not found\n");
-		return PTR_ERR(clk_ce);
+		ret = PTR_ERR(clk_ce);
+		goto put_clk_cs;
 	}
 
 	ret = ttc_setup_clocksource(clk_cs, timer_baseaddr, timer_width);
 	if (ret)
-		return ret;
+		goto put_clk_ce;
 
 	ret = ttc_setup_clockevent(clk_ce, timer_baseaddr + 4, irq);
 	if (ret)
-		return ret;
+		goto put_clk_ce;
 
 	pr_info("%pOFn #0 at %p, irq=%d\n", timer, timer_baseaddr, irq);
 
 	return 0;
+
+put_clk_ce:
+	clk_put(clk_ce);
+put_clk_cs:
+	clk_put(clk_cs);
+	return ret;
 }
 
 static const struct of_device_id ttc_timer_of_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-davinci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-davinci.c
@@ -257,21 +257,25 @@
 				resource_size(&timer_cfg->reg),
 				"davinci-timer")) {
 		pr_err("Unable to request memory region\n");
-		return -EBUSY;
+		rv = -EBUSY;
+		goto exit_clk_disable;
 	}
 
 	base = ioremap(timer_cfg->reg.start, resource_size(&timer_cfg->reg));
 	if (!base) {
 		pr_err("Unable to map the register range\n");
-		return -ENOMEM;
+		rv = -ENOMEM;
+		goto exit_mem_region;
 	}
 
 	davinci_timer_init(base);
 	tick_rate = clk_get_rate(clk);
 
 	clockevent = kzalloc(sizeof(*clockevent), GFP_KERNEL);
-	if (!clockevent)
-		return -ENOMEM;
+	if (!clockevent) {
+		rv = -ENOMEM;
+		goto exit_iounmap_base;
+	}
 
 	clockevent->dev.name = "tim12";
 	clockevent->dev.features = CLOCK_EVT_FEAT_ONESHOT;
@@ -296,7 +300,7 @@
 			 "clockevent/tim12", clockevent);
 	if (rv) {
 		pr_err("Unable to request the clockevent interrupt\n");
-		return rv;
+		goto exit_free_clockevent;
 	}
 
 	davinci_clocksource.dev.rating = 300;
@@ -323,13 +327,27 @@
 	rv = clocksource_register_hz(&davinci_clocksource.dev, tick_rate);
 	if (rv) {
 		pr_err("Unable to register clocksource\n");
-		return rv;
+		goto exit_free_irq;
 	}
 
 	sched_clock_register(davinci_timer_read_sched_clock,
 			     DAVINCI_TIMER_CLKSRC_BITS, tick_rate);
 
 	return 0;
+
+exit_free_irq:
+	free_irq(timer_cfg->irq[DAVINCI_TIMER_CLOCKEVENT_IRQ].start,
+			clockevent);
+exit_free_clockevent:
+	kfree(clockevent);
+exit_iounmap_base:
+	iounmap(base);
+exit_mem_region:
+	release_mem_region(timer_cfg->reg.start,
+			   resource_size(&timer_cfg->reg));
+exit_clk_disable:
+	clk_disable_unprepare(clk);
+	return rv;
 }
 
 static int __init of_davinci_timer_register(struct device_node *np)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-imx-gpt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-imx-gpt.c
@@ -454,12 +454,16 @@
 		return -ENOMEM;
 
 	imxtm->base = of_iomap(np, 0);
-	if (!imxtm->base)
-		return -ENXIO;
+	if (!imxtm->base) {
+		ret = -ENXIO;
+		goto err_kfree;
+	}
 
 	imxtm->irq = irq_of_parse_and_map(np, 0);
-	if (imxtm->irq <= 0)
-		return -EINVAL;
+	if (imxtm->irq <= 0) {
+		ret = -EINVAL;
+		goto err_kfree;
+	}
 
 	imxtm->clk_ipg = of_clk_get_by_name(np, "ipg");
 
@@ -472,11 +476,15 @@
 
 	ret = _mxc_timer_init(imxtm);
 	if (ret)
-		return ret;
+		goto err_kfree;
 
 	initialized = 1;
 
 	return 0;
+
+err_kfree:
+	kfree(imxtm);
+	return ret;
 }
 
 static int __init imx1_timer_init_dt(struct device_node *np)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-imx-tpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-imx-tpm.c
@@ -83,20 +83,28 @@
 static int tpm_set_next_event(unsigned long delta,
 				struct clock_event_device *evt)
 {
-	unsigned long next, now;
+	unsigned long next, prev, now;
 
-	next = tpm_read_counter();
-	next += delta;
+	prev = tpm_read_counter();
+	next = prev + delta;
 	writel(next, timer_base + TPM_C0V);
 	now = tpm_read_counter();
 
 	/*
+	 * Need to wait CNT increase at least 1 cycle to make sure
+	 * the C0V has been updated into HW.
+	 */
+	if ((next & 0xffffffff) != readl(timer_base + TPM_C0V))
+		while (now == tpm_read_counter())
+			;
+
+	/*
 	 * NOTE: We observed in a very small probability, the bus fabric
 	 * contention between GPU and A7 may results a few cycles delay
 	 * of writing CNT registers which may cause the min_delta event got
 	 * missed, so we need add a ETIME check here in case it happened.
 	 */
-	return (int)(next - now) <= 0 ? -ETIME : 0;
+	return (now - prev) >= delta ? -ETIME : 0;
 }
 
 static int tpm_set_state_oneshot(struct clock_event_device *evt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-ixp4xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-ixp4xx.c
@@ -282,7 +282,6 @@
 	}
 	ixp4xx_timer_register(base, timer_irq, timer_freq);
 }
-EXPORT_SYMBOL_GPL(ixp4xx_timer_setup);
 
 #ifdef CONFIG_OF
 static __init int ixp4xx_of_timer_init(struct device_node *np)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-microchip-pit64b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-microchip-pit64b.c
@@ -165,7 +165,7 @@
 	return mchp_pit64b_cnt_read(mchp_pit64b_cs_base);
 }
 
-static u64 mchp_pit64b_sched_read_clk(void)
+static u64 notrace mchp_pit64b_sched_read_clk(void)
 {
 	return mchp_pit64b_cnt_read(mchp_pit64b_cs_base);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-of.c
@@ -25,10 +25,7 @@
 
 	struct clock_event_device *clkevt = &to->clkevt;
 
-	if (of_irq->percpu)
-		free_percpu_irq(of_irq->irq, clkevt);
-	else
-		free_irq(of_irq->irq, clkevt);
+	free_irq(of_irq->irq, clkevt);
 }
 
 /**
@@ -42,9 +39,6 @@
  * - Get interrupt number by name
  * - Get interrupt number by index
  *
- * When the interrupt is per CPU, 'request_percpu_irq()' is called,
- * otherwise 'request_irq()' is used.
- *
  * Returns 0 on success, < 0 otherwise
  */
 static __init int timer_of_irq_init(struct device_node *np,
@@ -69,12 +63,9 @@
 		return -EINVAL;
 	}
 
-	ret = of_irq->percpu ?
-		request_percpu_irq(of_irq->irq, of_irq->handler,
-				   np->full_name, clkevt) :
-		request_irq(of_irq->irq, of_irq->handler,
-			    of_irq->flags ? of_irq->flags : IRQF_TIMER,
-			    np->full_name, clkevt);
+	ret = request_irq(of_irq->irq, of_irq->handler,
+			  of_irq->flags ? of_irq->flags : IRQF_TIMER,
+			  np->full_name, clkevt);
 	if (ret) {
 		pr_err("Failed to request irq %d for %pOF\n", of_irq->irq, np);
 		return ret;
@@ -157,9 +148,9 @@
 	of_base->base = of_base->name ?
 		of_io_request_and_map(np, of_base->index, of_base->name) :
 		of_iomap(np, of_base->index);
-	if (IS_ERR(of_base->base)) {
-		pr_err("Failed to iomap (%s)\n", of_base->name);
-		return PTR_ERR(of_base->base);
+	if (IS_ERR_OR_NULL(of_base->base)) {
+		pr_err("Failed to iomap (%s:%s)\n", np->name, of_base->name);
+		return of_base->base ? PTR_ERR(of_base->base) : -ENOMEM;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-of.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-of.h
@@ -11,7 +11,6 @@
 struct of_timer_irq {
 	int irq;
 	int index;
-	int percpu;
 	const char *name;
 	unsigned long flags;
 	irq_handler_t handler;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-oxnas-rps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-oxnas-rps.c
@@ -236,7 +236,7 @@
 	}
 
 	rps->irq = irq_of_parse_and_map(np, 0);
-	if (rps->irq < 0) {
+	if (!rps->irq) {
 		ret = -EINVAL;
 		goto err_iomap;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-qcom.c
@@ -233,6 +233,7 @@
 	}
 
 	if (of_property_read_u32(np, "clock-frequency", &freq)) {
+		iounmap(cpu0_base);
 		pr_err("Unknown frequency\n");
 		return -EINVAL;
 	}
@@ -243,7 +244,11 @@
 	freq /= 4;
 	writel_relaxed(DGT_CLK_CTL_DIV_4, source_base + DGT_CLK_CTL);
 
-	return msm_timer_init(freq, 32, irq, !!percpu_offset);
+	ret = msm_timer_init(freq, 32, irq, !!percpu_offset);
+	if (ret)
+		iounmap(cpu0_base);
+
+	return ret;
 }
 TIMER_OF_DECLARE(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
 TIMER_OF_DECLARE(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-sp804.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-sp804.c
@@ -155,14 +155,14 @@
 	return IRQ_HANDLED;
 }
 
-static inline void timer_shutdown(struct clock_event_device *evt)
+static inline void evt_timer_shutdown(struct clock_event_device *evt)
 {
 	writel(0, common_clkevt->ctrl);
 }
 
 static int sp804_shutdown(struct clock_event_device *evt)
 {
-	timer_shutdown(evt);
+	evt_timer_shutdown(evt);
 	return 0;
 }
 
@@ -171,7 +171,7 @@
 	unsigned long ctrl = TIMER_CTRL_32BIT | TIMER_CTRL_IE |
 			     TIMER_CTRL_PERIODIC | TIMER_CTRL_ENABLE;
 
-	timer_shutdown(evt);
+	evt_timer_shutdown(evt);
 	writel(common_clkevt->reload, common_clkevt->load);
 	writel(ctrl, common_clkevt->ctrl);
 	return 0;
@@ -259,6 +259,11 @@
 	struct clk *clk1, *clk2;
 	const char *name = of_get_property(np, "compatible", NULL);
 
+	if (initialized) {
+		pr_debug("%pOF: skipping further SP804 timer device\n", np);
+		return 0;
+	}
+
 	base = of_iomap(np, 0);
 	if (!base)
 		return -ENXIO;
@@ -270,11 +275,6 @@
 	writel(0, timer1_base + timer->ctrl);
 	writel(0, timer2_base + timer->ctrl);
 
-	if (initialized || !of_device_is_available(np)) {
-		ret = -EINVAL;
-		goto err;
-	}
-
 	clk1 = of_clk_get(np, 0);
 	if (IS_ERR(clk1))
 		clk1 = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/clocksource/timer-ti-dm-systimer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/clocksource/timer-ti-dm-systimer.c
@@ -241,8 +241,7 @@
 	bool quirk_unreliable_oscillator = false;
 
 	/* Quirk unreliable 32 KiHz oscillator with incomplete dts */
-	if (of_machine_is_compatible("ti,omap3-beagle") ||
-	    of_machine_is_compatible("timll,omap3-devkit8000")) {
+	if (of_machine_is_compatible("ti,omap3-beagle-ab4")) {
 		quirk_unreliable_oscillator = true;
 		counter_32k = -ENODEV;
 	}
@@ -346,8 +345,10 @@
 		return error;
 
 	r = clk_get_rate(clock);
-	if (!r)
+	if (!r) {
+		clk_disable_unprepare(clock);
 		return -ENODEV;
+	}
 
 	if (is_ick)
 		t->ick = clock;
@@ -695,9 +696,9 @@
 		return 0;
 	}
 
-	if (pa == 0x48034000)		/* dra7 dmtimer3 */
+	if (pa == 0x4882c000)           /* dra7 dmtimer15 */
 		return dmtimer_percpu_timer_init(np, 0);
-	else if (pa == 0x48036000)	/* dra7 dmtimer4 */
+	else if (pa == 0x4882e000)      /* dra7 dmtimer16 */
 		return dmtimer_percpu_timer_init(np, 1);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/comedi_fops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/comedi_fops.c
@@ -2402,6 +2402,18 @@
 
 			start += PAGE_SIZE;
 		}
+
+#ifdef CONFIG_MMU
+		/*
+		 * Leaving behind a partial mapping of a buffer we're about to
+		 * drop is unsafe, see remap_pfn_range_notrack().
+		 * We need to zap the range here ourselves instead of relying
+		 * on the automatic zapping in remap_pfn_range() because we call
+		 * remap_pfn_range() in a loop.
+		 */
+		if (retval)
+			zap_vma_ptes(vma, vma->vm_start, size);
+#endif
 	}
 
 	if (retval == 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/drivers/adv_pci1760.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/drivers/adv_pci1760.c
@@ -59,7 +59,7 @@
 #define PCI1760_CMD_CLR_IMB2		0x00	/* Clears IMB2 */
 #define PCI1760_CMD_SET_DO		0x01	/* Set output state */
 #define PCI1760_CMD_GET_DO		0x02	/* Read output status */
-#define PCI1760_CMD_GET_STATUS		0x03	/* Read current status */
+#define PCI1760_CMD_GET_STATUS		0x07	/* Read current status */
 #define PCI1760_CMD_GET_FW_VER		0x0e	/* Read firmware version */
 #define PCI1760_CMD_GET_HW_VER		0x0f	/* Read hardware version */
 #define PCI1760_CMD_SET_PWM_HI(x)	(0x10 + (x) * 2) /* Set "hi" period */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/drivers/comedi_test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/drivers/comedi_test.c
@@ -87,6 +87,8 @@
 	struct comedi_device *dev;	/* parent comedi device */
 	u64 ao_last_scan_time;		/* time of previous AO scan in usec */
 	unsigned int ao_scan_period;	/* AO scan period in usec */
+	bool ai_timer_enable:1;		/* should AI timer be running? */
+	bool ao_timer_enable:1;		/* should AO timer be running? */
 	unsigned short ao_loopbacks[N_CHANS];
 };
 
@@ -236,8 +238,12 @@
 			time_increment = devpriv->ai_convert_time - now;
 		else
 			time_increment = 1;
-		mod_timer(&devpriv->ai_timer,
-			  jiffies + usecs_to_jiffies(time_increment));
+		spin_lock(&dev->spinlock);
+		if (devpriv->ai_timer_enable) {
+			mod_timer(&devpriv->ai_timer,
+				  jiffies + usecs_to_jiffies(time_increment));
+		}
+		spin_unlock(&dev->spinlock);
 	}
 
 overrun:
@@ -393,9 +399,12 @@
 	 * Seem to need an extra jiffy here, otherwise timer expires slightly
 	 * early!
 	 */
+	spin_lock_bh(&dev->spinlock);
+	devpriv->ai_timer_enable = true;
 	devpriv->ai_timer.expires =
 		jiffies + usecs_to_jiffies(devpriv->ai_convert_period) + 1;
 	add_timer(&devpriv->ai_timer);
+	spin_unlock_bh(&dev->spinlock);
 	return 0;
 }
 
@@ -404,6 +413,9 @@
 {
 	struct waveform_private *devpriv = dev->private;
 
+	spin_lock_bh(&dev->spinlock);
+	devpriv->ai_timer_enable = false;
+	spin_unlock_bh(&dev->spinlock);
 	if (in_softirq()) {
 		/* Assume we were called from the timer routine itself. */
 		del_timer(&devpriv->ai_timer);
@@ -495,8 +507,12 @@
 		unsigned int time_inc = devpriv->ao_last_scan_time +
 					devpriv->ao_scan_period - now;
 
-		mod_timer(&devpriv->ao_timer,
-			  jiffies + usecs_to_jiffies(time_inc));
+		spin_lock(&dev->spinlock);
+		if (devpriv->ao_timer_enable) {
+			mod_timer(&devpriv->ao_timer,
+				  jiffies + usecs_to_jiffies(time_inc));
+		}
+		spin_unlock(&dev->spinlock);
 	}
 
 underrun:
@@ -517,9 +533,12 @@
 	async->inttrig = NULL;
 
 	devpriv->ao_last_scan_time = ktime_to_us(ktime_get());
+	spin_lock_bh(&dev->spinlock);
+	devpriv->ao_timer_enable = true;
 	devpriv->ao_timer.expires =
 		jiffies + usecs_to_jiffies(devpriv->ao_scan_period);
 	add_timer(&devpriv->ao_timer);
+	spin_unlock_bh(&dev->spinlock);
 
 	return 1;
 }
@@ -604,6 +623,9 @@
 	struct waveform_private *devpriv = dev->private;
 
 	s->async->inttrig = NULL;
+	spin_lock_bh(&dev->spinlock);
+	devpriv->ao_timer_enable = false;
+	spin_unlock_bh(&dev->spinlock);
 	if (in_softirq()) {
 		/* Assume we were called from the timer routine itself. */
 		del_timer(&devpriv->ao_timer);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/drivers/dt9812.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/drivers/dt9812.c
@@ -32,6 +32,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/errno.h>
+#include <linux/slab.h>
 #include <linux/uaccess.h>
 
 #include "../comedi_usb.h"
@@ -237,22 +238,42 @@
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
+	size_t tbuf_size;
 	int count, ret;
+	void *tbuf;
 
-	cmd.cmd = cpu_to_le32(DT9812_R_FLASH_DATA);
-	cmd.u.flash_data_info.address =
+	tbuf_size = max(sizeof(*cmd), buf_size);
+
+	tbuf = kzalloc(tbuf_size, GFP_KERNEL);
+	if (!tbuf)
+		return -ENOMEM;
+
+	cmd = tbuf;
+
+	cmd->cmd = cpu_to_le32(DT9812_R_FLASH_DATA);
+	cmd->u.flash_data_info.address =
 	    cpu_to_le16(DT9812_DIAGS_BOARD_INFO_ADDR + offset);
-	cmd.u.flash_data_info.numbytes = cpu_to_le16(buf_size);
+	cmd->u.flash_data_info.numbytes = cpu_to_le16(buf_size);
 
 	/* DT9812 only responds to 32 byte writes!! */
 	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			   &cmd, 32, &count, DT9812_USB_TIMEOUT);
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
 	if (ret)
-		return ret;
+		goto out;
+
+	ret = usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
+			   tbuf, buf_size, &count, DT9812_USB_TIMEOUT);
+	if (!ret) {
+		if (count == buf_size)
+			memcpy(buf, tbuf, buf_size);
+		else
+			ret = -EREMOTEIO;
+	}
+out:
+	kfree(tbuf);
 
-	return usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
-			    buf, buf_size, &count, DT9812_USB_TIMEOUT);
+	return ret;
 }
 
 static int dt9812_read_multiple_registers(struct comedi_device *dev,
@@ -261,22 +282,42 @@
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
 	int i, count, ret;
+	size_t buf_size;
+	void *buf;
+
+	buf_size = max_t(size_t, sizeof(*cmd), reg_count);
+
+	buf = kzalloc(buf_size, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	cmd = buf;
 
-	cmd.cmd = cpu_to_le32(DT9812_R_MULTI_BYTE_REG);
-	cmd.u.read_multi_info.count = reg_count;
+	cmd->cmd = cpu_to_le32(DT9812_R_MULTI_BYTE_REG);
+	cmd->u.read_multi_info.count = reg_count;
 	for (i = 0; i < reg_count; i++)
-		cmd.u.read_multi_info.address[i] = address[i];
+		cmd->u.read_multi_info.address[i] = address[i];
 
 	/* DT9812 only responds to 32 byte writes!! */
 	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			   &cmd, 32, &count, DT9812_USB_TIMEOUT);
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
 	if (ret)
-		return ret;
+		goto out;
 
-	return usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
-			    value, reg_count, &count, DT9812_USB_TIMEOUT);
+	ret = usb_bulk_msg(usb, usb_rcvbulkpipe(usb, devpriv->cmd_rd.addr),
+			   buf, reg_count, &count, DT9812_USB_TIMEOUT);
+	if (!ret) {
+		if (count == reg_count)
+			memcpy(value, buf, reg_count);
+		else
+			ret = -EREMOTEIO;
+	}
+out:
+	kfree(buf);
+
+	return ret;
 }
 
 static int dt9812_write_multiple_registers(struct comedi_device *dev,
@@ -285,19 +326,27 @@
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
 	int i, count;
+	int ret;
 
-	cmd.cmd = cpu_to_le32(DT9812_W_MULTI_BYTE_REG);
-	cmd.u.read_multi_info.count = reg_count;
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
+
+	cmd->cmd = cpu_to_le32(DT9812_W_MULTI_BYTE_REG);
+	cmd->u.read_multi_info.count = reg_count;
 	for (i = 0; i < reg_count; i++) {
-		cmd.u.write_multi_info.write[i].address = address[i];
-		cmd.u.write_multi_info.write[i].value = value[i];
+		cmd->u.write_multi_info.write[i].address = address[i];
+		cmd->u.write_multi_info.write[i].value = value[i];
 	}
 
 	/* DT9812 only responds to 32 byte writes!! */
-	return usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			    &cmd, 32, &count, DT9812_USB_TIMEOUT);
+	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
+	kfree(cmd);
+
+	return ret;
 }
 
 static int dt9812_rmw_multiple_registers(struct comedi_device *dev,
@@ -306,17 +355,25 @@
 {
 	struct usb_device *usb = comedi_to_usb_dev(dev);
 	struct dt9812_private *devpriv = dev->private;
-	struct dt9812_usb_cmd cmd;
+	struct dt9812_usb_cmd *cmd;
 	int i, count;
+	int ret;
+
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
 
-	cmd.cmd = cpu_to_le32(DT9812_RMW_MULTI_BYTE_REG);
-	cmd.u.rmw_multi_info.count = reg_count;
+	cmd->cmd = cpu_to_le32(DT9812_RMW_MULTI_BYTE_REG);
+	cmd->u.rmw_multi_info.count = reg_count;
 	for (i = 0; i < reg_count; i++)
-		cmd.u.rmw_multi_info.rmw[i] = rmw[i];
+		cmd->u.rmw_multi_info.rmw[i] = rmw[i];
 
 	/* DT9812 only responds to 32 byte writes!! */
-	return usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
-			    &cmd, 32, &count, DT9812_USB_TIMEOUT);
+	ret = usb_bulk_msg(usb, usb_sndbulkpipe(usb, devpriv->cmd_wr.addr),
+			   cmd, sizeof(*cmd), &count, DT9812_USB_TIMEOUT);
+	kfree(cmd);
+
+	return ret;
 }
 
 static int dt9812_digital_in(struct comedi_device *dev, u8 *bits)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/drivers/ni_routing/tools/convert_c_to_py.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/drivers/ni_routing/tools/convert_c_to_py.c
@@ -140,6 +140,11 @@
 {
 	FILE *fp = fopen("ni_values.py", "w");
 
+	if (fp == NULL) {
+		fprintf(stderr, "Could not open file!");
+		return -1;
+	}
+
 	/* write route register values */
 	fprintf(fp, "ni_route_values = {\n");
 	for (int i = 0; ni_all_route_values[i]; ++i)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/drivers/ni_usb6501.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/drivers/ni_usb6501.c
@@ -144,6 +144,10 @@
 					   0x00, 0x00, 0x00, 0x02,
 					   0x00, 0x00, 0x00, 0x00};
 
+/* Largest supported packets */
+static const size_t TX_MAX_SIZE	= sizeof(SET_PORT_DIR_REQUEST);
+static const size_t RX_MAX_SIZE	= sizeof(READ_PORT_RESPONSE);
+
 enum commands {
 	READ_PORT,
 	WRITE_PORT,
@@ -501,6 +505,12 @@
 	if (!devpriv->ep_rx || !devpriv->ep_tx)
 		return -ENODEV;
 
+	if (usb_endpoint_maxp(devpriv->ep_rx) < RX_MAX_SIZE)
+		return -ENODEV;
+
+	if (usb_endpoint_maxp(devpriv->ep_tx) < TX_MAX_SIZE)
+		return -ENODEV;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/comedi/drivers/vmk80xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/comedi/drivers/vmk80xx.c
@@ -90,6 +90,9 @@
 #define IC3_VERSION		BIT(0)
 #define IC6_VERSION		BIT(1)
 
+#define MIN_BUF_SIZE		64
+#define PACKET_TIMEOUT		10000	/* ms */
+
 enum vmk80xx_model {
 	VMK8055_MODEL,
 	VMK8061_MODEL
@@ -157,22 +160,21 @@
 	__u8 rx_addr;
 	unsigned int tx_pipe;
 	unsigned int rx_pipe;
-	size_t size;
+	size_t tx_size;
+	size_t rx_size;
 
 	tx_addr = devpriv->ep_tx->bEndpointAddress;
 	rx_addr = devpriv->ep_rx->bEndpointAddress;
 	tx_pipe = usb_sndbulkpipe(usb, tx_addr);
 	rx_pipe = usb_rcvbulkpipe(usb, rx_addr);
+	tx_size = usb_endpoint_maxp(devpriv->ep_tx);
+	rx_size = usb_endpoint_maxp(devpriv->ep_rx);
 
-	/*
-	 * The max packet size attributes of the K8061
-	 * input/output endpoints are identical
-	 */
-	size = usb_endpoint_maxp(devpriv->ep_tx);
+	usb_bulk_msg(usb, tx_pipe, devpriv->usb_tx_buf, tx_size, NULL,
+		     PACKET_TIMEOUT);
 
-	usb_bulk_msg(usb, tx_pipe, devpriv->usb_tx_buf,
-		     size, NULL, devpriv->ep_tx->bInterval);
-	usb_bulk_msg(usb, rx_pipe, devpriv->usb_rx_buf, size, NULL, HZ * 10);
+	usb_bulk_msg(usb, rx_pipe, devpriv->usb_rx_buf, rx_size, NULL,
+		     PACKET_TIMEOUT);
 }
 
 static int vmk80xx_read_packet(struct comedi_device *dev)
@@ -191,7 +193,7 @@
 	pipe = usb_rcvintpipe(usb, ep->bEndpointAddress);
 	return usb_interrupt_msg(usb, pipe, devpriv->usb_rx_buf,
 				 usb_endpoint_maxp(ep), NULL,
-				 HZ * 10);
+				 PACKET_TIMEOUT);
 }
 
 static int vmk80xx_write_packet(struct comedi_device *dev, int cmd)
@@ -212,7 +214,7 @@
 	pipe = usb_sndintpipe(usb, ep->bEndpointAddress);
 	return usb_interrupt_msg(usb, pipe, devpriv->usb_tx_buf,
 				 usb_endpoint_maxp(ep), NULL,
-				 HZ * 10);
+				 PACKET_TIMEOUT);
 }
 
 static int vmk80xx_reset_device(struct comedi_device *dev)
@@ -640,33 +642,22 @@
 	struct vmk80xx_private *devpriv = dev->private;
 	struct usb_interface *intf = comedi_to_usb_interface(dev);
 	struct usb_host_interface *iface_desc = intf->cur_altsetting;
-	struct usb_endpoint_descriptor *ep_desc;
-	int i;
-
-	if (iface_desc->desc.bNumEndpoints != 2)
-		return -ENODEV;
-
-	for (i = 0; i < iface_desc->desc.bNumEndpoints; i++) {
-		ep_desc = &iface_desc->endpoint[i].desc;
-
-		if (usb_endpoint_is_int_in(ep_desc) ||
-		    usb_endpoint_is_bulk_in(ep_desc)) {
-			if (!devpriv->ep_rx)
-				devpriv->ep_rx = ep_desc;
-			continue;
-		}
+	struct usb_endpoint_descriptor *ep_rx_desc, *ep_tx_desc;
+	int ret;
 
-		if (usb_endpoint_is_int_out(ep_desc) ||
-		    usb_endpoint_is_bulk_out(ep_desc)) {
-			if (!devpriv->ep_tx)
-				devpriv->ep_tx = ep_desc;
-			continue;
-		}
-	}
+	if (devpriv->model == VMK8061_MODEL)
+		ret = usb_find_common_endpoints(iface_desc, &ep_rx_desc,
+						&ep_tx_desc, NULL, NULL);
+	else
+		ret = usb_find_common_endpoints(iface_desc, NULL, NULL,
+						&ep_rx_desc, &ep_tx_desc);
 
-	if (!devpriv->ep_rx || !devpriv->ep_tx)
+	if (ret)
 		return -ENODEV;
 
+	devpriv->ep_rx = ep_rx_desc;
+	devpriv->ep_tx = ep_tx_desc;
+
 	if (!usb_endpoint_maxp(devpriv->ep_rx) || !usb_endpoint_maxp(devpriv->ep_tx))
 		return -EINVAL;
 
@@ -678,12 +669,12 @@
 	struct vmk80xx_private *devpriv = dev->private;
 	size_t size;
 
-	size = usb_endpoint_maxp(devpriv->ep_rx);
+	size = max(usb_endpoint_maxp(devpriv->ep_rx), MIN_BUF_SIZE);
 	devpriv->usb_rx_buf = kzalloc(size, GFP_KERNEL);
 	if (!devpriv->usb_rx_buf)
 		return -ENOMEM;
 
-	size = usb_endpoint_maxp(devpriv->ep_tx);
+	size = max(usb_endpoint_maxp(devpriv->ep_tx), MIN_BUF_SIZE);
 	devpriv->usb_tx_buf = kzalloc(size, GFP_KERNEL);
 	if (!devpriv->usb_tx_buf)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/104-quad-8.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/104-quad-8.c
@@ -61,10 +61,6 @@
 #define QUAD8_REG_CHAN_OP 0x11
 #define QUAD8_REG_INDEX_INPUT_LEVELS 0x16
 #define QUAD8_DIFF_ENCODER_CABLE_STATUS 0x17
-/* Borrow Toggle flip-flop */
-#define QUAD8_FLAG_BT BIT(0)
-/* Carry Toggle flip-flop */
-#define QUAD8_FLAG_CT BIT(1)
 /* Error flag */
 #define QUAD8_FLAG_E BIT(4)
 /* Up/Down flag */
@@ -97,6 +93,9 @@
 #define QUAD8_CMR_QUADRATURE_X2 0x10
 #define QUAD8_CMR_QUADRATURE_X4 0x18
 
+/* Each Counter is 24 bits wide */
+#define LS7267_CNTR_MAX GENMASK(23, 0)
+
 static int quad8_signal_read(struct counter_device *counter,
 			     struct counter_signal *signal,
 			     enum counter_signal_level *level)
@@ -117,21 +116,13 @@
 }
 
 static int quad8_count_read(struct counter_device *counter,
-	struct counter_count *count, unsigned long *val)
+			    struct counter_count *count, u64 *val)
 {
 	struct quad8 *const priv = counter->priv;
 	const int base_offset = priv->base + 2 * count->id;
-	unsigned int flags;
-	unsigned int borrow;
-	unsigned int carry;
 	int i;
 
-	flags = inb(base_offset + 1);
-	borrow = flags & QUAD8_FLAG_BT;
-	carry = !!(flags & QUAD8_FLAG_CT);
-
-	/* Borrow XOR Carry effectively doubles count range */
-	*val = (unsigned long)(borrow ^ carry) << 24;
+	*val = 0;
 
 	mutex_lock(&priv->lock);
 
@@ -148,14 +139,13 @@
 }
 
 static int quad8_count_write(struct counter_device *counter,
-	struct counter_count *count, unsigned long val)
+			     struct counter_count *count, u64 val)
 {
 	struct quad8 *const priv = counter->priv;
 	const int base_offset = priv->base + 2 * count->id;
 	int i;
 
-	/* Only 24-bit values are supported */
-	if (val > 0xFFFFFF)
+	if (val > LS7267_CNTR_MAX)
 		return -ERANGE;
 
 	mutex_lock(&priv->lock);
@@ -188,22 +178,16 @@
 	return 0;
 }
 
-enum quad8_count_function {
-	QUAD8_COUNT_FUNCTION_PULSE_DIRECTION = 0,
-	QUAD8_COUNT_FUNCTION_QUADRATURE_X1,
-	QUAD8_COUNT_FUNCTION_QUADRATURE_X2,
-	QUAD8_COUNT_FUNCTION_QUADRATURE_X4
-};
-
 static const enum counter_function quad8_count_functions_list[] = {
-	[QUAD8_COUNT_FUNCTION_PULSE_DIRECTION] = COUNTER_FUNCTION_PULSE_DIRECTION,
-	[QUAD8_COUNT_FUNCTION_QUADRATURE_X1] = COUNTER_FUNCTION_QUADRATURE_X1_A,
-	[QUAD8_COUNT_FUNCTION_QUADRATURE_X2] = COUNTER_FUNCTION_QUADRATURE_X2_A,
-	[QUAD8_COUNT_FUNCTION_QUADRATURE_X4] = COUNTER_FUNCTION_QUADRATURE_X4
+	COUNTER_FUNCTION_PULSE_DIRECTION,
+	COUNTER_FUNCTION_QUADRATURE_X1_A,
+	COUNTER_FUNCTION_QUADRATURE_X2_A,
+	COUNTER_FUNCTION_QUADRATURE_X4,
 };
 
-static int quad8_function_get(struct counter_device *counter,
-	struct counter_count *count, size_t *function)
+static int quad8_function_read(struct counter_device *counter,
+			       struct counter_count *count,
+			       enum counter_function *function)
 {
 	struct quad8 *const priv = counter->priv;
 	const int id = count->id;
@@ -213,25 +197,26 @@
 	if (priv->quadrature_mode[id])
 		switch (priv->quadrature_scale[id]) {
 		case 0:
-			*function = QUAD8_COUNT_FUNCTION_QUADRATURE_X1;
+			*function = COUNTER_FUNCTION_QUADRATURE_X1_A;
 			break;
 		case 1:
-			*function = QUAD8_COUNT_FUNCTION_QUADRATURE_X2;
+			*function = COUNTER_FUNCTION_QUADRATURE_X2_A;
 			break;
 		case 2:
-			*function = QUAD8_COUNT_FUNCTION_QUADRATURE_X4;
+			*function = COUNTER_FUNCTION_QUADRATURE_X4;
 			break;
 		}
 	else
-		*function = QUAD8_COUNT_FUNCTION_PULSE_DIRECTION;
+		*function = COUNTER_FUNCTION_PULSE_DIRECTION;
 
 	mutex_unlock(&priv->lock);
 
 	return 0;
 }
 
-static int quad8_function_set(struct counter_device *counter,
-	struct counter_count *count, size_t function)
+static int quad8_function_write(struct counter_device *counter,
+				struct counter_count *count,
+				enum counter_function function)
 {
 	struct quad8 *const priv = counter->priv;
 	const int id = count->id;
@@ -247,7 +232,7 @@
 	mode_cfg = priv->count_mode[id] << 1;
 	idr_cfg = priv->index_polarity[id] << 1;
 
-	if (function == QUAD8_COUNT_FUNCTION_PULSE_DIRECTION) {
+	if (function == COUNTER_FUNCTION_PULSE_DIRECTION) {
 		*quadrature_mode = 0;
 
 		/* Quadrature scaling only available in quadrature mode */
@@ -263,15 +248,15 @@
 		*quadrature_mode = 1;
 
 		switch (function) {
-		case QUAD8_COUNT_FUNCTION_QUADRATURE_X1:
+		case COUNTER_FUNCTION_QUADRATURE_X1_A:
 			*scale = 0;
 			mode_cfg |= QUAD8_CMR_QUADRATURE_X1;
 			break;
-		case QUAD8_COUNT_FUNCTION_QUADRATURE_X2:
+		case COUNTER_FUNCTION_QUADRATURE_X2_A:
 			*scale = 1;
 			mode_cfg |= QUAD8_CMR_QUADRATURE_X2;
 			break;
-		case QUAD8_COUNT_FUNCTION_QUADRATURE_X4:
+		case COUNTER_FUNCTION_QUADRATURE_X4:
 			*scale = 2;
 			mode_cfg |= QUAD8_CMR_QUADRATURE_X4;
 			break;
@@ -290,8 +275,9 @@
 	return 0;
 }
 
-static void quad8_direction_get(struct counter_device *counter,
-	struct counter_count *count, enum counter_count_direction *direction)
+static int quad8_direction_read(struct counter_device *counter,
+				struct counter_count *count,
+				enum counter_count_direction *direction)
 {
 	const struct quad8 *const priv = counter->priv;
 	unsigned int ud_flag;
@@ -302,76 +288,74 @@
 
 	*direction = (ud_flag) ? COUNTER_COUNT_DIRECTION_FORWARD :
 		COUNTER_COUNT_DIRECTION_BACKWARD;
-}
 
-enum quad8_synapse_action {
-	QUAD8_SYNAPSE_ACTION_NONE = 0,
-	QUAD8_SYNAPSE_ACTION_RISING_EDGE,
-	QUAD8_SYNAPSE_ACTION_FALLING_EDGE,
-	QUAD8_SYNAPSE_ACTION_BOTH_EDGES
-};
+	return 0;
+}
 
 static const enum counter_synapse_action quad8_index_actions_list[] = {
-	[QUAD8_SYNAPSE_ACTION_NONE] = COUNTER_SYNAPSE_ACTION_NONE,
-	[QUAD8_SYNAPSE_ACTION_RISING_EDGE] = COUNTER_SYNAPSE_ACTION_RISING_EDGE
+	COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
 };
 
 static const enum counter_synapse_action quad8_synapse_actions_list[] = {
-	[QUAD8_SYNAPSE_ACTION_NONE] = COUNTER_SYNAPSE_ACTION_NONE,
-	[QUAD8_SYNAPSE_ACTION_RISING_EDGE] = COUNTER_SYNAPSE_ACTION_RISING_EDGE,
-	[QUAD8_SYNAPSE_ACTION_FALLING_EDGE] = COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
-	[QUAD8_SYNAPSE_ACTION_BOTH_EDGES] = COUNTER_SYNAPSE_ACTION_BOTH_EDGES
+	COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
+	COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
+	COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
 };
 
-static int quad8_action_get(struct counter_device *counter,
-	struct counter_count *count, struct counter_synapse *synapse,
-	size_t *action)
+static int quad8_action_read(struct counter_device *counter,
+			     struct counter_count *count,
+			     struct counter_synapse *synapse,
+			     enum counter_synapse_action *action)
 {
 	struct quad8 *const priv = counter->priv;
 	int err;
-	size_t function = 0;
+	enum counter_function function;
 	const size_t signal_a_id = count->synapses[0].signal->id;
 	enum counter_count_direction direction;
 
 	/* Handle Index signals */
 	if (synapse->signal->id >= 16) {
-		if (priv->preset_enable[count->id])
-			*action = QUAD8_SYNAPSE_ACTION_RISING_EDGE;
+		if (!priv->preset_enable[count->id])
+			*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 		else
-			*action = QUAD8_SYNAPSE_ACTION_NONE;
+			*action = COUNTER_SYNAPSE_ACTION_NONE;
 
 		return 0;
 	}
 
-	err = quad8_function_get(counter, count, &function);
+	err = quad8_function_read(counter, count, &function);
 	if (err)
 		return err;
 
 	/* Default action mode */
-	*action = QUAD8_SYNAPSE_ACTION_NONE;
+	*action = COUNTER_SYNAPSE_ACTION_NONE;
 
 	/* Determine action mode based on current count function mode */
 	switch (function) {
-	case QUAD8_COUNT_FUNCTION_PULSE_DIRECTION:
+	case COUNTER_FUNCTION_PULSE_DIRECTION:
 		if (synapse->signal->id == signal_a_id)
-			*action = QUAD8_SYNAPSE_ACTION_RISING_EDGE;
+			*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 		return 0;
-	case QUAD8_COUNT_FUNCTION_QUADRATURE_X1:
+	case COUNTER_FUNCTION_QUADRATURE_X1_A:
 		if (synapse->signal->id == signal_a_id) {
-			quad8_direction_get(counter, count, &direction);
+			err = quad8_direction_read(counter, count, &direction);
+			if (err)
+				return err;
 
 			if (direction == COUNTER_COUNT_DIRECTION_FORWARD)
-				*action = QUAD8_SYNAPSE_ACTION_RISING_EDGE;
+				*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 			else
-				*action = QUAD8_SYNAPSE_ACTION_FALLING_EDGE;
+				*action = COUNTER_SYNAPSE_ACTION_FALLING_EDGE;
 		}
 		return 0;
-	case QUAD8_COUNT_FUNCTION_QUADRATURE_X2:
+	case COUNTER_FUNCTION_QUADRATURE_X2_A:
 		if (synapse->signal->id == signal_a_id)
-			*action = QUAD8_SYNAPSE_ACTION_BOTH_EDGES;
+			*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		return 0;
-	case QUAD8_COUNT_FUNCTION_QUADRATURE_X4:
-		*action = QUAD8_SYNAPSE_ACTION_BOTH_EDGES;
+	case COUNTER_FUNCTION_QUADRATURE_X4:
+		*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		return 0;
 	default:
 		/* should never reach this path */
@@ -383,9 +367,9 @@
 	.signal_read = quad8_signal_read,
 	.count_read = quad8_count_read,
 	.count_write = quad8_count_write,
-	.function_get = quad8_function_get,
-	.function_set = quad8_function_set,
-	.action_get = quad8_action_get
+	.function_read = quad8_function_read,
+	.function_write = quad8_function_write,
+	.action_read = quad8_action_read
 };
 
 static const char *const quad8_index_polarity_modes[] = {
@@ -394,7 +378,8 @@
 };
 
 static int quad8_index_polarity_get(struct counter_device *counter,
-	struct counter_signal *signal, size_t *index_polarity)
+				    struct counter_signal *signal,
+				    u32 *index_polarity)
 {
 	const struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id - 16;
@@ -405,7 +390,8 @@
 }
 
 static int quad8_index_polarity_set(struct counter_device *counter,
-	struct counter_signal *signal, size_t index_polarity)
+				    struct counter_signal *signal,
+				    u32 index_polarity)
 {
 	struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id - 16;
@@ -426,20 +412,14 @@
 	return 0;
 }
 
-static struct counter_signal_enum_ext quad8_index_pol_enum = {
-	.items = quad8_index_polarity_modes,
-	.num_items = ARRAY_SIZE(quad8_index_polarity_modes),
-	.get = quad8_index_polarity_get,
-	.set = quad8_index_polarity_set
-};
-
 static const char *const quad8_synchronous_modes[] = {
 	"non-synchronous",
 	"synchronous"
 };
 
 static int quad8_synchronous_mode_get(struct counter_device *counter,
-	struct counter_signal *signal, size_t *synchronous_mode)
+				      struct counter_signal *signal,
+				      u32 *synchronous_mode)
 {
 	const struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id - 16;
@@ -450,7 +430,8 @@
 }
 
 static int quad8_synchronous_mode_set(struct counter_device *counter,
-	struct counter_signal *signal, size_t synchronous_mode)
+				      struct counter_signal *signal,
+				      u32 synchronous_mode)
 {
 	struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id - 16;
@@ -477,22 +458,18 @@
 	return 0;
 }
 
-static struct counter_signal_enum_ext quad8_syn_mode_enum = {
-	.items = quad8_synchronous_modes,
-	.num_items = ARRAY_SIZE(quad8_synchronous_modes),
-	.get = quad8_synchronous_mode_get,
-	.set = quad8_synchronous_mode_set
-};
-
-static ssize_t quad8_count_floor_read(struct counter_device *counter,
-	struct counter_count *count, void *private, char *buf)
+static int quad8_count_floor_read(struct counter_device *counter,
+				  struct counter_count *count, u64 *floor)
 {
 	/* Only a floor of 0 is supported */
-	return sprintf(buf, "0\n");
+	*floor = 0;
+
+	return 0;
 }
 
-static int quad8_count_mode_get(struct counter_device *counter,
-	struct counter_count *count, size_t *cnt_mode)
+static int quad8_count_mode_read(struct counter_device *counter,
+				 struct counter_count *count,
+				 enum counter_count_mode *cnt_mode)
 {
 	const struct quad8 *const priv = counter->priv;
 
@@ -515,26 +492,28 @@
 	return 0;
 }
 
-static int quad8_count_mode_set(struct counter_device *counter,
-	struct counter_count *count, size_t cnt_mode)
+static int quad8_count_mode_write(struct counter_device *counter,
+				  struct counter_count *count,
+				  enum counter_count_mode cnt_mode)
 {
 	struct quad8 *const priv = counter->priv;
+	unsigned int count_mode;
 	unsigned int mode_cfg;
 	const int base_offset = priv->base + 2 * count->id + 1;
 
 	/* Map Generic Counter count mode to 104-QUAD-8 count mode */
 	switch (cnt_mode) {
 	case COUNTER_COUNT_MODE_NORMAL:
-		cnt_mode = 0;
+		count_mode = 0;
 		break;
 	case COUNTER_COUNT_MODE_RANGE_LIMIT:
-		cnt_mode = 1;
+		count_mode = 1;
 		break;
 	case COUNTER_COUNT_MODE_NON_RECYCLE:
-		cnt_mode = 2;
+		count_mode = 2;
 		break;
 	case COUNTER_COUNT_MODE_MODULO_N:
-		cnt_mode = 3;
+		count_mode = 3;
 		break;
 	default:
 		/* should never reach this path */
@@ -543,10 +522,10 @@
 
 	mutex_lock(&priv->lock);
 
-	priv->count_mode[count->id] = cnt_mode;
+	priv->count_mode[count->id] = count_mode;
 
 	/* Set count mode configuration value */
-	mode_cfg = cnt_mode << 1;
+	mode_cfg = count_mode << 1;
 
 	/* Add quadrature mode configuration */
 	if (priv->quadrature_mode[count->id])
@@ -560,56 +539,35 @@
 	return 0;
 }
 
-static struct counter_count_enum_ext quad8_cnt_mode_enum = {
-	.items = counter_count_mode_str,
-	.num_items = ARRAY_SIZE(counter_count_mode_str),
-	.get = quad8_count_mode_get,
-	.set = quad8_count_mode_set
-};
-
-static ssize_t quad8_count_direction_read(struct counter_device *counter,
-	struct counter_count *count, void *priv, char *buf)
-{
-	enum counter_count_direction dir;
-
-	quad8_direction_get(counter, count, &dir);
-
-	return sprintf(buf, "%s\n", counter_count_direction_str[dir]);
-}
-
-static ssize_t quad8_count_enable_read(struct counter_device *counter,
-	struct counter_count *count, void *private, char *buf)
+static int quad8_count_enable_read(struct counter_device *counter,
+				   struct counter_count *count, u8 *enable)
 {
 	const struct quad8 *const priv = counter->priv;
 
-	return sprintf(buf, "%u\n", priv->ab_enable[count->id]);
+	*enable = priv->ab_enable[count->id];
+
+	return 0;
 }
 
-static ssize_t quad8_count_enable_write(struct counter_device *counter,
-	struct counter_count *count, void *private, const char *buf, size_t len)
+static int quad8_count_enable_write(struct counter_device *counter,
+				    struct counter_count *count, u8 enable)
 {
 	struct quad8 *const priv = counter->priv;
 	const int base_offset = priv->base + 2 * count->id;
-	int err;
-	bool ab_enable;
 	unsigned int ior_cfg;
 
-	err = kstrtobool(buf, &ab_enable);
-	if (err)
-		return err;
-
 	mutex_lock(&priv->lock);
 
-	priv->ab_enable[count->id] = ab_enable;
+	priv->ab_enable[count->id] = enable;
 
-	ior_cfg = ab_enable | priv->preset_enable[count->id] << 1;
+	ior_cfg = enable | priv->preset_enable[count->id] << 1;
 
 	/* Load I/O control configuration */
 	outb(QUAD8_CTR_IOR | ior_cfg, base_offset + 1);
 
 	mutex_unlock(&priv->lock);
 
-	return len;
+	return 0;
 }
 
 static const char *const quad8_noise_error_states[] = {
@@ -618,7 +576,7 @@
 };
 
 static int quad8_error_noise_get(struct counter_device *counter,
-	struct counter_count *count, size_t *noise_error)
+				 struct counter_count *count, u32 *noise_error)
 {
 	const struct quad8 *const priv = counter->priv;
 	const int base_offset = priv->base + 2 * count->id + 1;
@@ -628,18 +586,14 @@
 	return 0;
 }
 
-static struct counter_count_enum_ext quad8_error_noise_enum = {
-	.items = quad8_noise_error_states,
-	.num_items = ARRAY_SIZE(quad8_noise_error_states),
-	.get = quad8_error_noise_get
-};
-
-static ssize_t quad8_count_preset_read(struct counter_device *counter,
-	struct counter_count *count, void *private, char *buf)
+static int quad8_count_preset_read(struct counter_device *counter,
+				   struct counter_count *count, u64 *preset)
 {
 	const struct quad8 *const priv = counter->priv;
 
-	return sprintf(buf, "%u\n", priv->preset[count->id]);
+	*preset = priv->preset[count->id];
+
+	return 0;
 }
 
 static void quad8_preset_register_set(struct quad8 *const priv, const int id,
@@ -658,19 +612,12 @@
 		outb(preset >> (8 * i), base_offset);
 }
 
-static ssize_t quad8_count_preset_write(struct counter_device *counter,
-	struct counter_count *count, void *private, const char *buf, size_t len)
+static int quad8_count_preset_write(struct counter_device *counter,
+				    struct counter_count *count, u64 preset)
 {
 	struct quad8 *const priv = counter->priv;
-	unsigned int preset;
-	int ret;
 
-	ret = kstrtouint(buf, 0, &preset);
-	if (ret)
-		return ret;
-
-	/* Only 24-bit values are supported */
-	if (preset > 0xFFFFFF)
+	if (preset > LS7267_CNTR_MAX)
 		return -ERANGE;
 
 	mutex_lock(&priv->lock);
@@ -679,11 +626,11 @@
 
 	mutex_unlock(&priv->lock);
 
-	return len;
+	return 0;
 }
 
-static ssize_t quad8_count_ceiling_read(struct counter_device *counter,
-	struct counter_count *count, void *private, char *buf)
+static int quad8_count_ceiling_read(struct counter_device *counter,
+				    struct counter_count *count, u64 *ceiling)
 {
 	struct quad8 *const priv = counter->priv;
 
@@ -693,29 +640,24 @@
 	switch (priv->count_mode[count->id]) {
 	case 1:
 	case 3:
-		mutex_unlock(&priv->lock);
-		return sprintf(buf, "%u\n", priv->preset[count->id]);
+		*ceiling = priv->preset[count->id];
+		break;
+	default:
+		*ceiling = LS7267_CNTR_MAX;
+		break;
 	}
 
 	mutex_unlock(&priv->lock);
 
-	/* By default 0x1FFFFFF (25 bits unsigned) is maximum count */
-	return sprintf(buf, "33554431\n");
+	return 0;
 }
 
-static ssize_t quad8_count_ceiling_write(struct counter_device *counter,
-	struct counter_count *count, void *private, const char *buf, size_t len)
+static int quad8_count_ceiling_write(struct counter_device *counter,
+				     struct counter_count *count, u64 ceiling)
 {
 	struct quad8 *const priv = counter->priv;
-	unsigned int ceiling;
-	int ret;
-
-	ret = kstrtouint(buf, 0, &ceiling);
-	if (ret)
-		return ret;
 
-	/* Only 24-bit values are supported */
-	if (ceiling > 0xFFFFFF)
+	if (ceiling > LS7267_CNTR_MAX)
 		return -ERANGE;
 
 	mutex_lock(&priv->lock);
@@ -726,7 +668,7 @@
 	case 3:
 		quad8_preset_register_set(priv, count->id, ceiling);
 		mutex_unlock(&priv->lock);
-		return len;
+		return 0;
 	}
 
 	mutex_unlock(&priv->lock);
@@ -734,27 +676,25 @@
 	return -EINVAL;
 }
 
-static ssize_t quad8_count_preset_enable_read(struct counter_device *counter,
-	struct counter_count *count, void *private, char *buf)
+static int quad8_count_preset_enable_read(struct counter_device *counter,
+					  struct counter_count *count,
+					  u8 *preset_enable)
 {
 	const struct quad8 *const priv = counter->priv;
 
-	return sprintf(buf, "%u\n", !priv->preset_enable[count->id]);
+	*preset_enable = !priv->preset_enable[count->id];
+
+	return 0;
 }
 
-static ssize_t quad8_count_preset_enable_write(struct counter_device *counter,
-	struct counter_count *count, void *private, const char *buf, size_t len)
+static int quad8_count_preset_enable_write(struct counter_device *counter,
+					   struct counter_count *count,
+					   u8 preset_enable)
 {
 	struct quad8 *const priv = counter->priv;
 	const int base_offset = priv->base + 2 * count->id + 1;
-	bool preset_enable;
-	int ret;
 	unsigned int ior_cfg;
 
-	ret = kstrtobool(buf, &preset_enable);
-	if (ret)
-		return ret;
-
 	/* Preset enable is active low in Input/Output Control register */
 	preset_enable = !preset_enable;
 
@@ -762,25 +702,24 @@
 
 	priv->preset_enable[count->id] = preset_enable;
 
-	ior_cfg = priv->ab_enable[count->id] | (unsigned int)preset_enable << 1;
+	ior_cfg = priv->ab_enable[count->id] | preset_enable << 1;
 
 	/* Load I/O control configuration to Input / Output Control Register */
 	outb(QUAD8_CTR_IOR | ior_cfg, base_offset);
 
 	mutex_unlock(&priv->lock);
 
-	return len;
+	return 0;
 }
 
-static ssize_t quad8_signal_cable_fault_read(struct counter_device *counter,
-					     struct counter_signal *signal,
-					     void *private, char *buf)
+static int quad8_signal_cable_fault_read(struct counter_device *counter,
+					 struct counter_signal *signal,
+					 u8 *cable_fault)
 {
 	struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id / 2;
 	bool disabled;
 	unsigned int status;
-	unsigned int fault;
 
 	mutex_lock(&priv->lock);
 
@@ -797,36 +736,31 @@
 	mutex_unlock(&priv->lock);
 
 	/* Mask respective channel and invert logic */
-	fault = !(status & BIT(channel_id));
+	*cable_fault = !(status & BIT(channel_id));
 
-	return sprintf(buf, "%u\n", fault);
+	return 0;
 }
 
-static ssize_t quad8_signal_cable_fault_enable_read(
-	struct counter_device *counter, struct counter_signal *signal,
-	void *private, char *buf)
+static int quad8_signal_cable_fault_enable_read(struct counter_device *counter,
+						struct counter_signal *signal,
+						u8 *enable)
 {
 	const struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id / 2;
-	const unsigned int enb = !!(priv->cable_fault_enable & BIT(channel_id));
 
-	return sprintf(buf, "%u\n", enb);
+	*enable = !!(priv->cable_fault_enable & BIT(channel_id));
+
+	return 0;
 }
 
-static ssize_t quad8_signal_cable_fault_enable_write(
-	struct counter_device *counter, struct counter_signal *signal,
-	void *private, const char *buf, size_t len)
+static int quad8_signal_cable_fault_enable_write(struct counter_device *counter,
+						 struct counter_signal *signal,
+						 u8 enable)
 {
 	struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id / 2;
-	bool enable;
-	int ret;
 	unsigned int cable_fault_enable;
 
-	ret = kstrtobool(buf, &enable);
-	if (ret)
-		return ret;
-
 	mutex_lock(&priv->lock);
 
 	if (enable)
@@ -841,31 +775,27 @@
 
 	mutex_unlock(&priv->lock);
 
-	return len;
+	return 0;
 }
 
-static ssize_t quad8_signal_fck_prescaler_read(struct counter_device *counter,
-	struct counter_signal *signal, void *private, char *buf)
+static int quad8_signal_fck_prescaler_read(struct counter_device *counter,
+					   struct counter_signal *signal,
+					   u8 *prescaler)
 {
 	const struct quad8 *const priv = counter->priv;
-	const size_t channel_id = signal->id / 2;
 
-	return sprintf(buf, "%u\n", priv->fck_prescaler[channel_id]);
+	*prescaler = priv->fck_prescaler[signal->id / 2];
+
+	return 0;
 }
 
-static ssize_t quad8_signal_fck_prescaler_write(struct counter_device *counter,
-	struct counter_signal *signal, void *private, const char *buf,
-	size_t len)
+static int quad8_signal_fck_prescaler_write(struct counter_device *counter,
+					    struct counter_signal *signal,
+					    u8 prescaler)
 {
 	struct quad8 *const priv = counter->priv;
 	const size_t channel_id = signal->id / 2;
 	const int base_offset = priv->base + 2 * channel_id;
-	u8 prescaler;
-	int ret;
-
-	ret = kstrtou8(buf, 0, &prescaler);
-	if (ret)
-		return ret;
 
 	mutex_lock(&priv->lock);
 
@@ -881,31 +811,30 @@
 
 	mutex_unlock(&priv->lock);
 
-	return len;
+	return 0;
 }
 
-static const struct counter_signal_ext quad8_signal_ext[] = {
-	{
-		.name = "cable_fault",
-		.read = quad8_signal_cable_fault_read
-	},
-	{
-		.name = "cable_fault_enable",
-		.read = quad8_signal_cable_fault_enable_read,
-		.write = quad8_signal_cable_fault_enable_write
-	},
-	{
-		.name = "filter_clock_prescaler",
-		.read = quad8_signal_fck_prescaler_read,
-		.write = quad8_signal_fck_prescaler_write
-	}
-};
-
-static const struct counter_signal_ext quad8_index_ext[] = {
-	COUNTER_SIGNAL_ENUM("index_polarity", &quad8_index_pol_enum),
-	COUNTER_SIGNAL_ENUM_AVAILABLE("index_polarity",	&quad8_index_pol_enum),
-	COUNTER_SIGNAL_ENUM("synchronous_mode", &quad8_syn_mode_enum),
-	COUNTER_SIGNAL_ENUM_AVAILABLE("synchronous_mode", &quad8_syn_mode_enum)
+static struct counter_comp quad8_signal_ext[] = {
+	COUNTER_COMP_SIGNAL_BOOL("cable_fault", quad8_signal_cable_fault_read,
+				 NULL),
+	COUNTER_COMP_SIGNAL_BOOL("cable_fault_enable",
+				 quad8_signal_cable_fault_enable_read,
+				 quad8_signal_cable_fault_enable_write),
+	COUNTER_COMP_SIGNAL_U8("filter_clock_prescaler",
+			       quad8_signal_fck_prescaler_read,
+			       quad8_signal_fck_prescaler_write)
+};
+
+static DEFINE_COUNTER_ENUM(quad8_index_pol_enum, quad8_index_polarity_modes);
+static DEFINE_COUNTER_ENUM(quad8_synch_mode_enum, quad8_synchronous_modes);
+
+static struct counter_comp quad8_index_ext[] = {
+	COUNTER_COMP_SIGNAL_ENUM("index_polarity", quad8_index_polarity_get,
+				 quad8_index_polarity_set,
+				 quad8_index_pol_enum),
+	COUNTER_COMP_SIGNAL_ENUM("synchronous_mode", quad8_synchronous_mode_get,
+				 quad8_synchronous_mode_set,
+				 quad8_synch_mode_enum),
 };
 
 #define QUAD8_QUAD_SIGNAL(_id, _name) {		\
@@ -974,39 +903,30 @@
 	QUAD8_COUNT_SYNAPSES(6), QUAD8_COUNT_SYNAPSES(7)
 };
 
-static const struct counter_count_ext quad8_count_ext[] = {
-	{
-		.name = "ceiling",
-		.read = quad8_count_ceiling_read,
-		.write = quad8_count_ceiling_write
-	},
-	{
-		.name = "floor",
-		.read = quad8_count_floor_read
-	},
-	COUNTER_COUNT_ENUM("count_mode", &quad8_cnt_mode_enum),
-	COUNTER_COUNT_ENUM_AVAILABLE("count_mode", &quad8_cnt_mode_enum),
-	{
-		.name = "direction",
-		.read = quad8_count_direction_read
-	},
-	{
-		.name = "enable",
-		.read = quad8_count_enable_read,
-		.write = quad8_count_enable_write
-	},
-	COUNTER_COUNT_ENUM("error_noise", &quad8_error_noise_enum),
-	COUNTER_COUNT_ENUM_AVAILABLE("error_noise", &quad8_error_noise_enum),
-	{
-		.name = "preset",
-		.read = quad8_count_preset_read,
-		.write = quad8_count_preset_write
-	},
-	{
-		.name = "preset_enable",
-		.read = quad8_count_preset_enable_read,
-		.write = quad8_count_preset_enable_write
-	}
+static const enum counter_count_mode quad8_cnt_modes[] = {
+	COUNTER_COUNT_MODE_NORMAL,
+	COUNTER_COUNT_MODE_RANGE_LIMIT,
+	COUNTER_COUNT_MODE_NON_RECYCLE,
+	COUNTER_COUNT_MODE_MODULO_N,
+};
+
+static DEFINE_COUNTER_AVAILABLE(quad8_count_mode_available, quad8_cnt_modes);
+
+static DEFINE_COUNTER_ENUM(quad8_error_noise_enum, quad8_noise_error_states);
+
+static struct counter_comp quad8_count_ext[] = {
+	COUNTER_COMP_CEILING(quad8_count_ceiling_read,
+			     quad8_count_ceiling_write),
+	COUNTER_COMP_FLOOR(quad8_count_floor_read, NULL),
+	COUNTER_COMP_COUNT_MODE(quad8_count_mode_read, quad8_count_mode_write,
+				quad8_count_mode_available),
+	COUNTER_COMP_DIRECTION(quad8_direction_read),
+	COUNTER_COMP_ENABLE(quad8_count_enable_read, quad8_count_enable_write),
+	COUNTER_COMP_COUNT_ENUM("error_noise", quad8_error_noise_get, NULL,
+				quad8_error_noise_enum),
+	COUNTER_COMP_PRESET(quad8_count_preset_read, quad8_count_preset_write),
+	COUNTER_COMP_PRESET_ENABLE(quad8_count_preset_enable_read,
+				   quad8_count_preset_enable_write),
 };
 
 #define QUAD8_COUNT(_id, _cntname) {					\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/Makefile
@@ -4,6 +4,7 @@
 #
 
 obj-$(CONFIG_COUNTER) += counter.o
+counter-y := counter-core.o counter-sysfs.o
 
 obj-$(CONFIG_104_QUAD_8)	+= 104-quad-8.o
 obj-$(CONFIG_INTERRUPT_CNT)		+= interrupt-cnt.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/counter-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/counter-core.c
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Generic Counter interface
+ * Copyright (C) 2020 William Breathitt Gray
+ */
+#include <linux/counter.h>
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/gfp.h>
+#include <linux/idr.h>
+#include <linux/init.h>
+#include <linux/module.h>
+
+#include "counter-sysfs.h"
+
+/* Provides a unique ID for each counter device */
+static DEFINE_IDA(counter_ida);
+
+static void counter_device_release(struct device *dev)
+{
+	ida_free(&counter_ida, dev->id);
+}
+
+static struct device_type counter_device_type = {
+	.name = "counter_device",
+	.release = counter_device_release,
+};
+
+static struct bus_type counter_bus_type = {
+	.name = "counter",
+	.dev_name = "counter",
+};
+
+/**
+ * counter_register - register Counter to the system
+ * @counter:	pointer to Counter to register
+ *
+ * This function registers a Counter to the system. A sysfs "counter" directory
+ * will be created and populated with sysfs attributes correlating with the
+ * Counter Signals, Synapses, and Counts respectively.
+ */
+int counter_register(struct counter_device *const counter)
+{
+	struct device *const dev = &counter->dev;
+	int id;
+	int err;
+
+	/* Acquire unique ID */
+	id = ida_alloc(&counter_ida, GFP_KERNEL);
+	if (id < 0)
+		return id;
+
+	/* Configure device structure for Counter */
+	dev->id = id;
+	dev->type = &counter_device_type;
+	dev->bus = &counter_bus_type;
+	if (counter->parent) {
+		dev->parent = counter->parent;
+		dev->of_node = counter->parent->of_node;
+	}
+	device_initialize(dev);
+	dev_set_drvdata(dev, counter);
+
+	/* Add Counter sysfs attributes */
+	err = counter_sysfs_add(counter);
+	if (err < 0)
+		goto err_free_id;
+
+	/* Add device to system */
+	err = device_add(dev);
+	if (err < 0)
+		goto err_free_id;
+
+	return 0;
+
+err_free_id:
+	put_device(dev);
+	return err;
+}
+EXPORT_SYMBOL_GPL(counter_register);
+
+/**
+ * counter_unregister - unregister Counter from the system
+ * @counter:	pointer to Counter to unregister
+ *
+ * The Counter is unregistered from the system.
+ */
+void counter_unregister(struct counter_device *const counter)
+{
+	if (!counter)
+		return;
+
+	device_unregister(&counter->dev);
+}
+EXPORT_SYMBOL_GPL(counter_unregister);
+
+static void devm_counter_release(void *counter)
+{
+	counter_unregister(counter);
+}
+
+/**
+ * devm_counter_register - Resource-managed counter_register
+ * @dev:	device to allocate counter_device for
+ * @counter:	pointer to Counter to register
+ *
+ * Managed counter_register. The Counter registered with this function is
+ * automatically unregistered on driver detach. This function calls
+ * counter_register internally. Refer to that function for more information.
+ *
+ * RETURNS:
+ * 0 on success, negative error number on failure.
+ */
+int devm_counter_register(struct device *dev,
+			  struct counter_device *const counter)
+{
+	int err;
+
+	err = counter_register(counter);
+	if (err < 0)
+		return err;
+
+	return devm_add_action_or_reset(dev, devm_counter_release, counter);
+}
+EXPORT_SYMBOL_GPL(devm_counter_register);
+
+static int __init counter_init(void)
+{
+	return bus_register(&counter_bus_type);
+}
+
+static void __exit counter_exit(void)
+{
+	bus_unregister(&counter_bus_type);
+}
+
+subsys_initcall(counter_init);
+module_exit(counter_exit);
+
+MODULE_AUTHOR("William Breathitt Gray <vilhelm.gray@gmail.com>");
+MODULE_DESCRIPTION("Generic Counter interface");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/counter-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/counter-sysfs.c
@@ -0,0 +1,849 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Generic Counter sysfs interface
+ * Copyright (C) 2020 William Breathitt Gray
+ */
+#include <linux/counter.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gfp.h>
+#include <linux/kernel.h>
+#include <linux/kstrtox.h>
+#include <linux/list.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include <linux/types.h>
+
+#include "counter-sysfs.h"
+
+/**
+ * struct counter_attribute - Counter sysfs attribute
+ * @dev_attr:	device attribute for sysfs
+ * @l:		node to add Counter attribute to attribute group list
+ * @comp:	Counter component callbacks and data
+ * @scope:	Counter scope of the attribute
+ * @parent:	pointer to the parent component
+ */
+struct counter_attribute {
+	struct device_attribute dev_attr;
+	struct list_head l;
+
+	struct counter_comp comp;
+	enum counter_scope scope;
+	void *parent;
+};
+
+#define to_counter_attribute(_dev_attr) \
+	container_of(_dev_attr, struct counter_attribute, dev_attr)
+
+/**
+ * struct counter_attribute_group - container for attribute group
+ * @name:	name of the attribute group
+ * @attr_list:	list to keep track of created attributes
+ * @num_attr:	number of attributes
+ */
+struct counter_attribute_group {
+	const char *name;
+	struct list_head attr_list;
+	size_t num_attr;
+};
+
+static const char *const counter_function_str[] = {
+	[COUNTER_FUNCTION_INCREASE] = "increase",
+	[COUNTER_FUNCTION_DECREASE] = "decrease",
+	[COUNTER_FUNCTION_PULSE_DIRECTION] = "pulse-direction",
+	[COUNTER_FUNCTION_QUADRATURE_X1_A] = "quadrature x1 a",
+	[COUNTER_FUNCTION_QUADRATURE_X1_B] = "quadrature x1 b",
+	[COUNTER_FUNCTION_QUADRATURE_X2_A] = "quadrature x2 a",
+	[COUNTER_FUNCTION_QUADRATURE_X2_B] = "quadrature x2 b",
+	[COUNTER_FUNCTION_QUADRATURE_X4] = "quadrature x4"
+};
+
+static const char *const counter_signal_value_str[] = {
+	[COUNTER_SIGNAL_LEVEL_LOW] = "low",
+	[COUNTER_SIGNAL_LEVEL_HIGH] = "high"
+};
+
+static const char *const counter_synapse_action_str[] = {
+	[COUNTER_SYNAPSE_ACTION_NONE] = "none",
+	[COUNTER_SYNAPSE_ACTION_RISING_EDGE] = "rising edge",
+	[COUNTER_SYNAPSE_ACTION_FALLING_EDGE] = "falling edge",
+	[COUNTER_SYNAPSE_ACTION_BOTH_EDGES] = "both edges"
+};
+
+static const char *const counter_count_direction_str[] = {
+	[COUNTER_COUNT_DIRECTION_FORWARD] = "forward",
+	[COUNTER_COUNT_DIRECTION_BACKWARD] = "backward"
+};
+
+static const char *const counter_count_mode_str[] = {
+	[COUNTER_COUNT_MODE_NORMAL] = "normal",
+	[COUNTER_COUNT_MODE_RANGE_LIMIT] = "range limit",
+	[COUNTER_COUNT_MODE_NON_RECYCLE] = "non-recycle",
+	[COUNTER_COUNT_MODE_MODULO_N] = "modulo-n"
+};
+
+static ssize_t counter_comp_u8_show(struct device *dev,
+				    struct device_attribute *attr, char *buf)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	struct counter_device *const counter = dev_get_drvdata(dev);
+	int err;
+	u8 data = 0;
+
+	switch (a->scope) {
+	case COUNTER_SCOPE_DEVICE:
+		err = a->comp.device_u8_read(counter, &data);
+		break;
+	case COUNTER_SCOPE_SIGNAL:
+		err = a->comp.signal_u8_read(counter, a->parent, &data);
+		break;
+	case COUNTER_SCOPE_COUNT:
+		err = a->comp.count_u8_read(counter, a->parent, &data);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (err < 0)
+		return err;
+
+	if (a->comp.type == COUNTER_COMP_BOOL)
+		/* data should already be boolean but ensure just to be safe */
+		data = !!data;
+
+	return sprintf(buf, "%u\n", (unsigned int)data);
+}
+
+static ssize_t counter_comp_u8_store(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t len)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	struct counter_device *const counter = dev_get_drvdata(dev);
+	int err;
+	bool bool_data = 0;
+	u8 data = 0;
+
+	if (a->comp.type == COUNTER_COMP_BOOL) {
+		err = kstrtobool(buf, &bool_data);
+		data = bool_data;
+	} else
+		err = kstrtou8(buf, 0, &data);
+	if (err < 0)
+		return err;
+
+	switch (a->scope) {
+	case COUNTER_SCOPE_DEVICE:
+		err = a->comp.device_u8_write(counter, data);
+		break;
+	case COUNTER_SCOPE_SIGNAL:
+		err = a->comp.signal_u8_write(counter, a->parent, data);
+		break;
+	case COUNTER_SCOPE_COUNT:
+		err = a->comp.count_u8_write(counter, a->parent, data);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (err < 0)
+		return err;
+
+	return len;
+}
+
+static ssize_t counter_comp_u32_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	struct counter_device *const counter = dev_get_drvdata(dev);
+	const struct counter_available *const avail = a->comp.priv;
+	int err;
+	u32 data = 0;
+
+	switch (a->scope) {
+	case COUNTER_SCOPE_DEVICE:
+		err = a->comp.device_u32_read(counter, &data);
+		break;
+	case COUNTER_SCOPE_SIGNAL:
+		err = a->comp.signal_u32_read(counter, a->parent, &data);
+		break;
+	case COUNTER_SCOPE_COUNT:
+		if (a->comp.type == COUNTER_COMP_SYNAPSE_ACTION)
+			err = a->comp.action_read(counter, a->parent,
+						  a->comp.priv, &data);
+		else
+			err = a->comp.count_u32_read(counter, a->parent, &data);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (err < 0)
+		return err;
+
+	switch (a->comp.type) {
+	case COUNTER_COMP_FUNCTION:
+		return sysfs_emit(buf, "%s\n", counter_function_str[data]);
+	case COUNTER_COMP_SIGNAL_LEVEL:
+		return sysfs_emit(buf, "%s\n", counter_signal_value_str[data]);
+	case COUNTER_COMP_SYNAPSE_ACTION:
+		return sysfs_emit(buf, "%s\n", counter_synapse_action_str[data]);
+	case COUNTER_COMP_ENUM:
+		return sysfs_emit(buf, "%s\n", avail->strs[data]);
+	case COUNTER_COMP_COUNT_DIRECTION:
+		return sysfs_emit(buf, "%s\n", counter_count_direction_str[data]);
+	case COUNTER_COMP_COUNT_MODE:
+		return sysfs_emit(buf, "%s\n", counter_count_mode_str[data]);
+	default:
+		return sprintf(buf, "%u\n", (unsigned int)data);
+	}
+}
+
+static int counter_find_enum(u32 *const enum_item, const u32 *const enums,
+			     const size_t num_enums, const char *const buf,
+			     const char *const string_array[])
+{
+	size_t index;
+
+	for (index = 0; index < num_enums; index++) {
+		*enum_item = enums[index];
+		if (sysfs_streq(buf, string_array[*enum_item]))
+			return 0;
+	}
+
+	return -EINVAL;
+}
+
+static ssize_t counter_comp_u32_store(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buf, size_t len)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	struct counter_device *const counter = dev_get_drvdata(dev);
+	struct counter_count *const count = a->parent;
+	struct counter_synapse *const synapse = a->comp.priv;
+	const struct counter_available *const avail = a->comp.priv;
+	int err;
+	u32 data = 0;
+
+	switch (a->comp.type) {
+	case COUNTER_COMP_FUNCTION:
+		err = counter_find_enum(&data, count->functions_list,
+					count->num_functions, buf,
+					counter_function_str);
+		break;
+	case COUNTER_COMP_SYNAPSE_ACTION:
+		err = counter_find_enum(&data, synapse->actions_list,
+					synapse->num_actions, buf,
+					counter_synapse_action_str);
+		break;
+	case COUNTER_COMP_ENUM:
+		err = __sysfs_match_string(avail->strs, avail->num_items, buf);
+		data = err;
+		break;
+	case COUNTER_COMP_COUNT_MODE:
+		err = counter_find_enum(&data, avail->enums, avail->num_items,
+					buf, counter_count_mode_str);
+		break;
+	default:
+		err = kstrtou32(buf, 0, &data);
+		break;
+	}
+	if (err < 0)
+		return err;
+
+	switch (a->scope) {
+	case COUNTER_SCOPE_DEVICE:
+		err = a->comp.device_u32_write(counter, data);
+		break;
+	case COUNTER_SCOPE_SIGNAL:
+		err = a->comp.signal_u32_write(counter, a->parent, data);
+		break;
+	case COUNTER_SCOPE_COUNT:
+		if (a->comp.type == COUNTER_COMP_SYNAPSE_ACTION)
+			err = a->comp.action_write(counter, count, synapse,
+						   data);
+		else
+			err = a->comp.count_u32_write(counter, count, data);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (err < 0)
+		return err;
+
+	return len;
+}
+
+static ssize_t counter_comp_u64_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	struct counter_device *const counter = dev_get_drvdata(dev);
+	int err;
+	u64 data = 0;
+
+	switch (a->scope) {
+	case COUNTER_SCOPE_DEVICE:
+		err = a->comp.device_u64_read(counter, &data);
+		break;
+	case COUNTER_SCOPE_SIGNAL:
+		err = a->comp.signal_u64_read(counter, a->parent, &data);
+		break;
+	case COUNTER_SCOPE_COUNT:
+		err = a->comp.count_u64_read(counter, a->parent, &data);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (err < 0)
+		return err;
+
+	return sprintf(buf, "%llu\n", (unsigned long long)data);
+}
+
+static ssize_t counter_comp_u64_store(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buf, size_t len)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	struct counter_device *const counter = dev_get_drvdata(dev);
+	int err;
+	u64 data = 0;
+
+	err = kstrtou64(buf, 0, &data);
+	if (err < 0)
+		return err;
+
+	switch (a->scope) {
+	case COUNTER_SCOPE_DEVICE:
+		err = a->comp.device_u64_write(counter, data);
+		break;
+	case COUNTER_SCOPE_SIGNAL:
+		err = a->comp.signal_u64_write(counter, a->parent, data);
+		break;
+	case COUNTER_SCOPE_COUNT:
+		err = a->comp.count_u64_write(counter, a->parent, data);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (err < 0)
+		return err;
+
+	return len;
+}
+
+static ssize_t enums_available_show(const u32 *const enums,
+				    const size_t num_enums,
+				    const char *const strs[], char *buf)
+{
+	size_t len = 0;
+	size_t index;
+
+	for (index = 0; index < num_enums; index++)
+		len += sysfs_emit_at(buf, len, "%s\n", strs[enums[index]]);
+
+	return len;
+}
+
+static ssize_t strs_available_show(const struct counter_available *const avail,
+				   char *buf)
+{
+	size_t len = 0;
+	size_t index;
+
+	for (index = 0; index < avail->num_items; index++)
+		len += sysfs_emit_at(buf, len, "%s\n", avail->strs[index]);
+
+	return len;
+}
+
+static ssize_t counter_comp_available_show(struct device *dev,
+					   struct device_attribute *attr,
+					   char *buf)
+{
+	const struct counter_attribute *const a = to_counter_attribute(attr);
+	const struct counter_count *const count = a->parent;
+	const struct counter_synapse *const synapse = a->comp.priv;
+	const struct counter_available *const avail = a->comp.priv;
+
+	switch (a->comp.type) {
+	case COUNTER_COMP_FUNCTION:
+		return enums_available_show(count->functions_list,
+					    count->num_functions,
+					    counter_function_str, buf);
+	case COUNTER_COMP_SYNAPSE_ACTION:
+		return enums_available_show(synapse->actions_list,
+					    synapse->num_actions,
+					    counter_synapse_action_str, buf);
+	case COUNTER_COMP_ENUM:
+		return strs_available_show(avail, buf);
+	case COUNTER_COMP_COUNT_MODE:
+		return enums_available_show(avail->enums, avail->num_items,
+					    counter_count_mode_str, buf);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int counter_avail_attr_create(struct device *const dev,
+	struct counter_attribute_group *const group,
+	const struct counter_comp *const comp, void *const parent)
+{
+	struct counter_attribute *counter_attr;
+	struct device_attribute *dev_attr;
+
+	counter_attr = devm_kzalloc(dev, sizeof(*counter_attr), GFP_KERNEL);
+	if (!counter_attr)
+		return -ENOMEM;
+
+	/* Configure Counter attribute */
+	counter_attr->comp.type = comp->type;
+	counter_attr->comp.priv = comp->priv;
+	counter_attr->parent = parent;
+
+	/* Initialize sysfs attribute */
+	dev_attr = &counter_attr->dev_attr;
+	sysfs_attr_init(&dev_attr->attr);
+
+	/* Configure device attribute */
+	dev_attr->attr.name = devm_kasprintf(dev, GFP_KERNEL, "%s_available",
+					     comp->name);
+	if (!dev_attr->attr.name)
+		return -ENOMEM;
+	dev_attr->attr.mode = 0444;
+	dev_attr->show = counter_comp_available_show;
+
+	/* Store list node */
+	list_add(&counter_attr->l, &group->attr_list);
+	group->num_attr++;
+
+	return 0;
+}
+
+static int counter_attr_create(struct device *const dev,
+			       struct counter_attribute_group *const group,
+			       const struct counter_comp *const comp,
+			       const enum counter_scope scope,
+			       void *const parent)
+{
+	struct counter_attribute *counter_attr;
+	struct device_attribute *dev_attr;
+
+	counter_attr = devm_kzalloc(dev, sizeof(*counter_attr), GFP_KERNEL);
+	if (!counter_attr)
+		return -ENOMEM;
+
+	/* Configure Counter attribute */
+	counter_attr->comp = *comp;
+	counter_attr->scope = scope;
+	counter_attr->parent = parent;
+
+	/* Configure device attribute */
+	dev_attr = &counter_attr->dev_attr;
+	sysfs_attr_init(&dev_attr->attr);
+	dev_attr->attr.name = comp->name;
+	switch (comp->type) {
+	case COUNTER_COMP_U8:
+	case COUNTER_COMP_BOOL:
+		if (comp->device_u8_read) {
+			dev_attr->attr.mode |= 0444;
+			dev_attr->show = counter_comp_u8_show;
+		}
+		if (comp->device_u8_write) {
+			dev_attr->attr.mode |= 0200;
+			dev_attr->store = counter_comp_u8_store;
+		}
+		break;
+	case COUNTER_COMP_SIGNAL_LEVEL:
+	case COUNTER_COMP_FUNCTION:
+	case COUNTER_COMP_SYNAPSE_ACTION:
+	case COUNTER_COMP_ENUM:
+	case COUNTER_COMP_COUNT_DIRECTION:
+	case COUNTER_COMP_COUNT_MODE:
+		if (comp->device_u32_read) {
+			dev_attr->attr.mode |= 0444;
+			dev_attr->show = counter_comp_u32_show;
+		}
+		if (comp->device_u32_write) {
+			dev_attr->attr.mode |= 0200;
+			dev_attr->store = counter_comp_u32_store;
+		}
+		break;
+	case COUNTER_COMP_U64:
+		if (comp->device_u64_read) {
+			dev_attr->attr.mode |= 0444;
+			dev_attr->show = counter_comp_u64_show;
+		}
+		if (comp->device_u64_write) {
+			dev_attr->attr.mode |= 0200;
+			dev_attr->store = counter_comp_u64_store;
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* Store list node */
+	list_add(&counter_attr->l, &group->attr_list);
+	group->num_attr++;
+
+	/* Create "*_available" attribute if needed */
+	switch (comp->type) {
+	case COUNTER_COMP_FUNCTION:
+	case COUNTER_COMP_SYNAPSE_ACTION:
+	case COUNTER_COMP_ENUM:
+	case COUNTER_COMP_COUNT_MODE:
+		return counter_avail_attr_create(dev, group, comp, parent);
+	default:
+		return 0;
+	}
+}
+
+static ssize_t counter_comp_name_show(struct device *dev,
+				      struct device_attribute *attr, char *buf)
+{
+	return sysfs_emit(buf, "%s\n", to_counter_attribute(attr)->comp.name);
+}
+
+static int counter_name_attr_create(struct device *const dev,
+				    struct counter_attribute_group *const group,
+				    const char *const name)
+{
+	struct counter_attribute *counter_attr;
+
+	counter_attr = devm_kzalloc(dev, sizeof(*counter_attr), GFP_KERNEL);
+	if (!counter_attr)
+		return -ENOMEM;
+
+	/* Configure Counter attribute */
+	counter_attr->comp.name = name;
+
+	/* Configure device attribute */
+	sysfs_attr_init(&counter_attr->dev_attr.attr);
+	counter_attr->dev_attr.attr.name = "name";
+	counter_attr->dev_attr.attr.mode = 0444;
+	counter_attr->dev_attr.show = counter_comp_name_show;
+
+	/* Store list node */
+	list_add(&counter_attr->l, &group->attr_list);
+	group->num_attr++;
+
+	return 0;
+}
+
+static struct counter_comp counter_signal_comp = {
+	.type = COUNTER_COMP_SIGNAL_LEVEL,
+	.name = "signal",
+};
+
+static int counter_signal_attrs_create(struct counter_device *const counter,
+	struct counter_attribute_group *const cattr_group,
+	struct counter_signal *const signal)
+{
+	const enum counter_scope scope = COUNTER_SCOPE_SIGNAL;
+	struct device *const dev = &counter->dev;
+	int err;
+	struct counter_comp comp;
+	size_t i;
+
+	/* Create main Signal attribute */
+	comp = counter_signal_comp;
+	comp.signal_u32_read = counter->ops->signal_read;
+	err = counter_attr_create(dev, cattr_group, &comp, scope, signal);
+	if (err < 0)
+		return err;
+
+	/* Create Signal name attribute */
+	err = counter_name_attr_create(dev, cattr_group, signal->name);
+	if (err < 0)
+		return err;
+
+	/* Create an attribute for each extension */
+	for (i = 0; i < signal->num_ext; i++) {
+		err = counter_attr_create(dev, cattr_group, signal->ext + i,
+					  scope, signal);
+		if (err < 0)
+			return err;
+	}
+
+	return 0;
+}
+
+static int counter_sysfs_signals_add(struct counter_device *const counter,
+	struct counter_attribute_group *const groups)
+{
+	size_t i;
+	int err;
+
+	/* Add each Signal */
+	for (i = 0; i < counter->num_signals; i++) {
+		/* Generate Signal attribute directory name */
+		groups[i].name = devm_kasprintf(&counter->dev, GFP_KERNEL,
+						"signal%zu", i);
+		if (!groups[i].name)
+			return -ENOMEM;
+
+		/* Create all attributes associated with Signal */
+		err = counter_signal_attrs_create(counter, groups + i,
+						  counter->signals + i);
+		if (err < 0)
+			return err;
+	}
+
+	return 0;
+}
+
+static int counter_sysfs_synapses_add(struct counter_device *const counter,
+	struct counter_attribute_group *const group,
+	struct counter_count *const count)
+{
+	size_t i;
+
+	/* Add each Synapse */
+	for (i = 0; i < count->num_synapses; i++) {
+		struct device *const dev = &counter->dev;
+		struct counter_synapse *synapse;
+		size_t id;
+		struct counter_comp comp;
+		int err;
+
+		synapse = count->synapses + i;
+
+		/* Generate Synapse action name */
+		id = synapse->signal - counter->signals;
+		comp.name = devm_kasprintf(dev, GFP_KERNEL, "signal%zu_action",
+					   id);
+		if (!comp.name)
+			return -ENOMEM;
+
+		/* Create action attribute */
+		comp.type = COUNTER_COMP_SYNAPSE_ACTION;
+		comp.action_read = counter->ops->action_read;
+		comp.action_write = counter->ops->action_write;
+		comp.priv = synapse;
+		err = counter_attr_create(dev, group, &comp,
+					  COUNTER_SCOPE_COUNT, count);
+		if (err < 0)
+			return err;
+	}
+
+	return 0;
+}
+
+static struct counter_comp counter_count_comp =
+	COUNTER_COMP_COUNT_U64("count", NULL, NULL);
+
+static struct counter_comp counter_function_comp = {
+	.type = COUNTER_COMP_FUNCTION,
+	.name = "function",
+};
+
+static int counter_count_attrs_create(struct counter_device *const counter,
+	struct counter_attribute_group *const cattr_group,
+	struct counter_count *const count)
+{
+	const enum counter_scope scope = COUNTER_SCOPE_COUNT;
+	struct device *const dev = &counter->dev;
+	int err;
+	struct counter_comp comp;
+	size_t i;
+
+	/* Create main Count attribute */
+	comp = counter_count_comp;
+	comp.count_u64_read = counter->ops->count_read;
+	comp.count_u64_write = counter->ops->count_write;
+	err = counter_attr_create(dev, cattr_group, &comp, scope, count);
+	if (err < 0)
+		return err;
+
+	/* Create Count name attribute */
+	err = counter_name_attr_create(dev, cattr_group, count->name);
+	if (err < 0)
+		return err;
+
+	/* Create Count function attribute */
+	comp = counter_function_comp;
+	comp.count_u32_read = counter->ops->function_read;
+	comp.count_u32_write = counter->ops->function_write;
+	err = counter_attr_create(dev, cattr_group, &comp, scope, count);
+	if (err < 0)
+		return err;
+
+	/* Create an attribute for each extension */
+	for (i = 0; i < count->num_ext; i++) {
+		err = counter_attr_create(dev, cattr_group, count->ext + i,
+					  scope, count);
+		if (err < 0)
+			return err;
+	}
+
+	return 0;
+}
+
+static int counter_sysfs_counts_add(struct counter_device *const counter,
+	struct counter_attribute_group *const groups)
+{
+	size_t i;
+	struct counter_count *count;
+	int err;
+
+	/* Add each Count */
+	for (i = 0; i < counter->num_counts; i++) {
+		count = counter->counts + i;
+
+		/* Generate Count attribute directory name */
+		groups[i].name = devm_kasprintf(&counter->dev, GFP_KERNEL,
+						"count%zu", i);
+		if (!groups[i].name)
+			return -ENOMEM;
+
+		/* Add sysfs attributes of the Synapses */
+		err = counter_sysfs_synapses_add(counter, groups + i, count);
+		if (err < 0)
+			return err;
+
+		/* Create all attributes associated with Count */
+		err = counter_count_attrs_create(counter, groups + i, count);
+		if (err < 0)
+			return err;
+	}
+
+	return 0;
+}
+
+static int counter_num_signals_read(struct counter_device *counter, u8 *val)
+{
+	*val = counter->num_signals;
+	return 0;
+}
+
+static int counter_num_counts_read(struct counter_device *counter, u8 *val)
+{
+	*val = counter->num_counts;
+	return 0;
+}
+
+static struct counter_comp counter_num_signals_comp =
+	COUNTER_COMP_DEVICE_U8("num_signals", counter_num_signals_read, NULL);
+
+static struct counter_comp counter_num_counts_comp =
+	COUNTER_COMP_DEVICE_U8("num_counts", counter_num_counts_read, NULL);
+
+static int counter_sysfs_attr_add(struct counter_device *const counter,
+				  struct counter_attribute_group *cattr_group)
+{
+	const enum counter_scope scope = COUNTER_SCOPE_DEVICE;
+	struct device *const dev = &counter->dev;
+	int err;
+	size_t i;
+
+	/* Add Signals sysfs attributes */
+	err = counter_sysfs_signals_add(counter, cattr_group);
+	if (err < 0)
+		return err;
+	cattr_group += counter->num_signals;
+
+	/* Add Counts sysfs attributes */
+	err = counter_sysfs_counts_add(counter, cattr_group);
+	if (err < 0)
+		return err;
+	cattr_group += counter->num_counts;
+
+	/* Create name attribute */
+	err = counter_name_attr_create(dev, cattr_group, counter->name);
+	if (err < 0)
+		return err;
+
+	/* Create num_signals attribute */
+	err = counter_attr_create(dev, cattr_group, &counter_num_signals_comp,
+				  scope, NULL);
+	if (err < 0)
+		return err;
+
+	/* Create num_counts attribute */
+	err = counter_attr_create(dev, cattr_group, &counter_num_counts_comp,
+				  scope, NULL);
+	if (err < 0)
+		return err;
+
+	/* Create an attribute for each extension */
+	for (i = 0; i < counter->num_ext; i++) {
+		err = counter_attr_create(dev, cattr_group, counter->ext + i,
+					  scope, NULL);
+		if (err < 0)
+			return err;
+	}
+
+	return 0;
+}
+
+/**
+ * counter_sysfs_add - Adds Counter sysfs attributes to the device structure
+ * @counter:	Pointer to the Counter device structure
+ *
+ * Counter sysfs attributes are created and added to the respective device
+ * structure for later registration to the system. Resource-managed memory
+ * allocation is performed by this function, and this memory should be freed
+ * when no longer needed (automatically by a device_unregister call, or
+ * manually by a devres_release_all call).
+ */
+int counter_sysfs_add(struct counter_device *const counter)
+{
+	struct device *const dev = &counter->dev;
+	const size_t num_groups = counter->num_signals + counter->num_counts + 1;
+	struct counter_attribute_group *cattr_groups;
+	size_t i, j;
+	int err;
+	struct attribute_group *groups;
+	struct counter_attribute *p;
+
+	/* Allocate space for attribute groups (signals, counts, and ext) */
+	cattr_groups = devm_kcalloc(dev, num_groups, sizeof(*cattr_groups),
+				    GFP_KERNEL);
+	if (!cattr_groups)
+		return -ENOMEM;
+
+	/* Initialize attribute lists */
+	for (i = 0; i < num_groups; i++)
+		INIT_LIST_HEAD(&cattr_groups[i].attr_list);
+
+	/* Add Counter device sysfs attributes */
+	err = counter_sysfs_attr_add(counter, cattr_groups);
+	if (err < 0)
+		return err;
+
+	/* Allocate attribute group pointers for association with device */
+	dev->groups = devm_kcalloc(dev, num_groups + 1, sizeof(*dev->groups),
+				   GFP_KERNEL);
+	if (!dev->groups)
+		return -ENOMEM;
+
+	/* Allocate space for attribute groups */
+	groups = devm_kcalloc(dev, num_groups, sizeof(*groups), GFP_KERNEL);
+	if (!groups)
+		return -ENOMEM;
+
+	/* Prepare each group of attributes for association */
+	for (i = 0; i < num_groups; i++) {
+		groups[i].name = cattr_groups[i].name;
+
+		/* Allocate space for attribute pointers */
+		groups[i].attrs = devm_kcalloc(dev,
+					       cattr_groups[i].num_attr + 1,
+					       sizeof(*groups[i].attrs),
+					       GFP_KERNEL);
+		if (!groups[i].attrs)
+			return -ENOMEM;
+
+		/* Add attribute pointers to attribute group */
+		j = 0;
+		list_for_each_entry(p, &cattr_groups[i].attr_list, l)
+			groups[i].attrs[j++] = &p->dev_attr.attr;
+
+		/* Associate attribute group */
+		dev->groups[i] = &groups[i];
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/counter-sysfs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/counter-sysfs.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Counter sysfs interface
+ * Copyright (C) 2020 William Breathitt Gray
+ */
+#ifndef _COUNTER_SYSFS_H_
+#define _COUNTER_SYSFS_H_
+
+#include <linux/counter.h>
+
+int counter_sysfs_add(struct counter_device *const counter);
+
+#endif /* _COUNTER_SYSFS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/ftm-quaddec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/ftm-quaddec.c
@@ -14,6 +14,7 @@
 #include <linux/mutex.h>
 #include <linux/counter.h>
 #include <linux/bitfield.h>
+#include <linux/types.h>
 
 #define FTM_FIELD_UPDATE(ftm, offset, mask, val)			\
 	({								\
@@ -115,8 +116,7 @@
 }
 
 static int ftm_quaddec_get_prescaler(struct counter_device *counter,
-				     struct counter_count *count,
-				     size_t *cnt_mode)
+				     struct counter_count *count, u32 *cnt_mode)
 {
 	struct ftm_quaddec *ftm = counter->priv;
 	uint32_t scflags;
@@ -129,8 +129,7 @@
 }
 
 static int ftm_quaddec_set_prescaler(struct counter_device *counter,
-				     struct counter_count *count,
-				     size_t cnt_mode)
+				     struct counter_count *count, u32 cnt_mode)
 {
 	struct ftm_quaddec *ftm = counter->priv;
 
@@ -151,33 +150,17 @@
 	"1", "2", "4", "8", "16", "32", "64", "128"
 };
 
-static struct counter_count_enum_ext ftm_quaddec_prescaler_enum = {
-	.items = ftm_quaddec_prescaler,
-	.num_items = ARRAY_SIZE(ftm_quaddec_prescaler),
-	.get = ftm_quaddec_get_prescaler,
-	.set = ftm_quaddec_set_prescaler
-};
-
-enum ftm_quaddec_synapse_action {
-	FTM_QUADDEC_SYNAPSE_ACTION_BOTH_EDGES,
-};
-
 static const enum counter_synapse_action ftm_quaddec_synapse_actions[] = {
-	[FTM_QUADDEC_SYNAPSE_ACTION_BOTH_EDGES] =
 	COUNTER_SYNAPSE_ACTION_BOTH_EDGES
 };
 
-enum ftm_quaddec_count_function {
-	FTM_QUADDEC_COUNT_ENCODER_MODE_1,
-};
-
 static const enum counter_function ftm_quaddec_count_functions[] = {
-	[FTM_QUADDEC_COUNT_ENCODER_MODE_1] = COUNTER_FUNCTION_QUADRATURE_X4
+	COUNTER_FUNCTION_QUADRATURE_X4
 };
 
 static int ftm_quaddec_count_read(struct counter_device *counter,
 				  struct counter_count *count,
-				  unsigned long *val)
+				  u64 *val)
 {
 	struct ftm_quaddec *const ftm = counter->priv;
 	uint32_t cntval;
@@ -191,7 +174,7 @@
 
 static int ftm_quaddec_count_write(struct counter_device *counter,
 				   struct counter_count *count,
-				   const unsigned long val)
+				   const u64 val)
 {
 	struct ftm_quaddec *const ftm = counter->priv;
 
@@ -205,21 +188,21 @@
 	return 0;
 }
 
-static int ftm_quaddec_count_function_get(struct counter_device *counter,
-					  struct counter_count *count,
-					  size_t *function)
+static int ftm_quaddec_count_function_read(struct counter_device *counter,
+					   struct counter_count *count,
+					   enum counter_function *function)
 {
-	*function = FTM_QUADDEC_COUNT_ENCODER_MODE_1;
+	*function = COUNTER_FUNCTION_QUADRATURE_X4;
 
 	return 0;
 }
 
-static int ftm_quaddec_action_get(struct counter_device *counter,
-				  struct counter_count *count,
-				  struct counter_synapse *synapse,
-				  size_t *action)
+static int ftm_quaddec_action_read(struct counter_device *counter,
+				   struct counter_count *count,
+				   struct counter_synapse *synapse,
+				   enum counter_synapse_action *action)
 {
-	*action = FTM_QUADDEC_SYNAPSE_ACTION_BOTH_EDGES;
+	*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 
 	return 0;
 }
@@ -227,8 +210,8 @@
 static const struct counter_ops ftm_quaddec_cnt_ops = {
 	.count_read = ftm_quaddec_count_read,
 	.count_write = ftm_quaddec_count_write,
-	.function_get = ftm_quaddec_count_function_get,
-	.action_get = ftm_quaddec_action_get,
+	.function_read = ftm_quaddec_count_function_read,
+	.action_read = ftm_quaddec_action_read,
 };
 
 static struct counter_signal ftm_quaddec_signals[] = {
@@ -255,9 +238,12 @@
 	}
 };
 
-static const struct counter_count_ext ftm_quaddec_count_ext[] = {
-	COUNTER_COUNT_ENUM("prescaler", &ftm_quaddec_prescaler_enum),
-	COUNTER_COUNT_ENUM_AVAILABLE("prescaler", &ftm_quaddec_prescaler_enum),
+static DEFINE_COUNTER_ENUM(ftm_quaddec_prescaler_enum, ftm_quaddec_prescaler);
+
+static struct counter_comp ftm_quaddec_count_ext[] = {
+	COUNTER_COMP_COUNT_ENUM("prescaler", ftm_quaddec_get_prescaler,
+				ftm_quaddec_set_prescaler,
+				ftm_quaddec_prescaler_enum),
 };
 
 static struct counter_count ftm_quaddec_counts = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/intel-qep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/intel-qep.c
@@ -62,13 +62,6 @@
 
 #define INTEL_QEP_CLK_PERIOD_NS		10
 
-#define INTEL_QEP_COUNTER_EXT_RW(_name)				\
-{								\
-	.name = #_name,						\
-	.read = _name##_read,					\
-	.write = _name##_write,					\
-}
-
 struct intel_qep {
 	struct counter_device counter;
 	struct mutex lock;
@@ -114,8 +107,7 @@
 }
 
 static int intel_qep_count_read(struct counter_device *counter,
-				struct counter_count *count,
-				unsigned long *val)
+				struct counter_count *count, u64 *val)
 {
 	struct intel_qep *const qep = counter->priv;
 
@@ -130,11 +122,11 @@
 	COUNTER_FUNCTION_QUADRATURE_X4,
 };
 
-static int intel_qep_function_get(struct counter_device *counter,
-				  struct counter_count *count,
-				  size_t *function)
+static int intel_qep_function_read(struct counter_device *counter,
+				   struct counter_count *count,
+				   enum counter_function *function)
 {
-	*function = 0;
+	*function = COUNTER_FUNCTION_QUADRATURE_X4;
 
 	return 0;
 }
@@ -143,19 +135,19 @@
 	COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
 };
 
-static int intel_qep_action_get(struct counter_device *counter,
-				struct counter_count *count,
-				struct counter_synapse *synapse,
-				size_t *action)
+static int intel_qep_action_read(struct counter_device *counter,
+				 struct counter_count *count,
+				 struct counter_synapse *synapse,
+				 enum counter_synapse_action *action)
 {
-	*action = 0;
+	*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 	return 0;
 }
 
 static const struct counter_ops intel_qep_counter_ops = {
 	.count_read = intel_qep_count_read,
-	.function_get = intel_qep_function_get,
-	.action_get = intel_qep_action_get,
+	.function_read = intel_qep_function_read,
+	.action_read = intel_qep_action_read,
 };
 
 #define INTEL_QEP_SIGNAL(_id, _name) {				\
@@ -181,31 +173,27 @@
 	INTEL_QEP_SYNAPSE(2),
 };
 
-static ssize_t ceiling_read(struct counter_device *counter,
-			    struct counter_count *count,
-			    void *priv, char *buf)
+static int intel_qep_ceiling_read(struct counter_device *counter,
+				  struct counter_count *count, u64 *ceiling)
 {
 	struct intel_qep *qep = counter->priv;
-	u32 reg;
 
 	pm_runtime_get_sync(qep->dev);
-	reg = intel_qep_readl(qep, INTEL_QEPMAX);
+	*ceiling = intel_qep_readl(qep, INTEL_QEPMAX);
 	pm_runtime_put(qep->dev);
 
-	return sysfs_emit(buf, "%u\n", reg);
+	return 0;
 }
 
-static ssize_t ceiling_write(struct counter_device *counter,
-			     struct counter_count *count,
-			     void *priv, const char *buf, size_t len)
+static int intel_qep_ceiling_write(struct counter_device *counter,
+				   struct counter_count *count, u64 max)
 {
 	struct intel_qep *qep = counter->priv;
-	u32 max;
-	int ret;
+	int ret = 0;
 
-	ret = kstrtou32(buf, 0, &max);
-	if (ret < 0)
-		return ret;
+	/* Intel QEP ceiling configuration only supports 32-bit values */
+	if (max != (u32)max)
+		return -ERANGE;
 
 	mutex_lock(&qep->lock);
 	if (qep->enabled) {
@@ -216,34 +204,28 @@
 	pm_runtime_get_sync(qep->dev);
 	intel_qep_writel(qep, INTEL_QEPMAX, max);
 	pm_runtime_put(qep->dev);
-	ret = len;
 
 out:
 	mutex_unlock(&qep->lock);
 	return ret;
 }
 
-static ssize_t enable_read(struct counter_device *counter,
-			   struct counter_count *count,
-			   void *priv, char *buf)
+static int intel_qep_enable_read(struct counter_device *counter,
+				 struct counter_count *count, u8 *enable)
 {
 	struct intel_qep *qep = counter->priv;
 
-	return sysfs_emit(buf, "%u\n", qep->enabled);
+	*enable = qep->enabled;
+
+	return 0;
 }
 
-static ssize_t enable_write(struct counter_device *counter,
-			    struct counter_count *count,
-			    void *priv, const char *buf, size_t len)
+static int intel_qep_enable_write(struct counter_device *counter,
+				  struct counter_count *count, u8 val)
 {
 	struct intel_qep *qep = counter->priv;
 	u32 reg;
-	bool val, changed;
-	int ret;
-
-	ret = kstrtobool(buf, &val);
-	if (ret)
-		return ret;
+	bool changed;
 
 	mutex_lock(&qep->lock);
 	changed = val ^ qep->enabled;
@@ -267,12 +249,12 @@
 
 out:
 	mutex_unlock(&qep->lock);
-	return len;
+	return 0;
 }
 
-static ssize_t spike_filter_ns_read(struct counter_device *counter,
-				    struct counter_count *count,
-				    void *priv, char *buf)
+static int intel_qep_spike_filter_ns_read(struct counter_device *counter,
+					  struct counter_count *count,
+					  u64 *length)
 {
 	struct intel_qep *qep = counter->priv;
 	u32 reg;
@@ -281,33 +263,31 @@
 	reg = intel_qep_readl(qep, INTEL_QEPCON);
 	if (!(reg & INTEL_QEPCON_FLT_EN)) {
 		pm_runtime_put(qep->dev);
-		return sysfs_emit(buf, "0\n");
+		return 0;
 	}
 	reg = INTEL_QEPFLT_MAX_COUNT(intel_qep_readl(qep, INTEL_QEPFLT));
 	pm_runtime_put(qep->dev);
 
-	return sysfs_emit(buf, "%u\n", (reg + 2) * INTEL_QEP_CLK_PERIOD_NS);
+	*length = (reg + 2) * INTEL_QEP_CLK_PERIOD_NS;
+
+	return 0;
 }
 
-static ssize_t spike_filter_ns_write(struct counter_device *counter,
-				     struct counter_count *count,
-				     void *priv, const char *buf, size_t len)
+static int intel_qep_spike_filter_ns_write(struct counter_device *counter,
+					   struct counter_count *count,
+					   u64 length)
 {
 	struct intel_qep *qep = counter->priv;
-	u32 reg, length;
+	u32 reg;
 	bool enable;
-	int ret;
-
-	ret = kstrtou32(buf, 0, &length);
-	if (ret < 0)
-		return ret;
+	int ret = 0;
 
 	/*
 	 * Spike filter length is (MAX_COUNT + 2) clock periods.
 	 * Disable filter when userspace writes 0, enable for valid
 	 * nanoseconds values and error out otherwise.
 	 */
-	length /= INTEL_QEP_CLK_PERIOD_NS;
+	do_div(length, INTEL_QEP_CLK_PERIOD_NS);
 	if (length == 0) {
 		enable = false;
 		length = 0;
@@ -336,16 +316,15 @@
 	intel_qep_writel(qep, INTEL_QEPFLT, length);
 	intel_qep_writel(qep, INTEL_QEPCON, reg);
 	pm_runtime_put(qep->dev);
-	ret = len;
 
 out:
 	mutex_unlock(&qep->lock);
 	return ret;
 }
 
-static ssize_t preset_enable_read(struct counter_device *counter,
-				  struct counter_count *count,
-				  void *priv, char *buf)
+static int intel_qep_preset_enable_read(struct counter_device *counter,
+					struct counter_count *count,
+					u8 *preset_enable)
 {
 	struct intel_qep *qep = counter->priv;
 	u32 reg;
@@ -353,21 +332,18 @@
 	pm_runtime_get_sync(qep->dev);
 	reg = intel_qep_readl(qep, INTEL_QEPCON);
 	pm_runtime_put(qep->dev);
-	return sysfs_emit(buf, "%u\n", !(reg & INTEL_QEPCON_COUNT_RST_MODE));
+
+	*preset_enable = !(reg & INTEL_QEPCON_COUNT_RST_MODE);
+
+	return 0;
 }
 
-static ssize_t preset_enable_write(struct counter_device *counter,
-				   struct counter_count *count,
-				   void *priv, const char *buf, size_t len)
+static int intel_qep_preset_enable_write(struct counter_device *counter,
+					 struct counter_count *count, u8 val)
 {
 	struct intel_qep *qep = counter->priv;
 	u32 reg;
-	bool val;
-	int ret;
-
-	ret = kstrtobool(buf, &val);
-	if (ret)
-		return ret;
+	int ret = 0;
 
 	mutex_lock(&qep->lock);
 	if (qep->enabled) {
@@ -384,7 +360,6 @@
 
 	intel_qep_writel(qep, INTEL_QEPCON, reg);
 	pm_runtime_put(qep->dev);
-	ret = len;
 
 out:
 	mutex_unlock(&qep->lock);
@@ -392,11 +367,14 @@
 	return ret;
 }
 
-static const struct counter_count_ext intel_qep_count_ext[] = {
-	INTEL_QEP_COUNTER_EXT_RW(ceiling),
-	INTEL_QEP_COUNTER_EXT_RW(enable),
-	INTEL_QEP_COUNTER_EXT_RW(spike_filter_ns),
-	INTEL_QEP_COUNTER_EXT_RW(preset_enable)
+static struct counter_comp intel_qep_count_ext[] = {
+	COUNTER_COMP_ENABLE(intel_qep_enable_read, intel_qep_enable_write),
+	COUNTER_COMP_CEILING(intel_qep_ceiling_read, intel_qep_ceiling_write),
+	COUNTER_COMP_PRESET_ENABLE(intel_qep_preset_enable_read,
+				   intel_qep_preset_enable_write),
+	COUNTER_COMP_COUNT_U64("spike_filter_ns",
+			       intel_qep_spike_filter_ns_read,
+			       intel_qep_spike_filter_ns_write),
 };
 
 static struct counter_count intel_qep_counter_count[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/interrupt-cnt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/interrupt-cnt.c
@@ -10,6 +10,7 @@
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/types.h>
 
 #define INTERRUPT_CNT_NAME "interrupt-cnt"
 
@@ -33,30 +34,23 @@
 	return IRQ_HANDLED;
 }
 
-static ssize_t interrupt_cnt_enable_read(struct counter_device *counter,
-					 struct counter_count *count,
-					 void *private, char *buf)
+static int interrupt_cnt_enable_read(struct counter_device *counter,
+				     struct counter_count *count, u8 *enable)
 {
 	struct interrupt_cnt_priv *priv = counter->priv;
 
-	return sysfs_emit(buf, "%d\n", priv->enabled);
+	*enable = priv->enabled;
+
+	return 0;
 }
 
-static ssize_t interrupt_cnt_enable_write(struct counter_device *counter,
-					  struct counter_count *count,
-					  void *private, const char *buf,
-					  size_t len)
+static int interrupt_cnt_enable_write(struct counter_device *counter,
+				      struct counter_count *count, u8 enable)
 {
 	struct interrupt_cnt_priv *priv = counter->priv;
-	bool enable;
-	ssize_t ret;
-
-	ret = kstrtobool(buf, &enable);
-	if (ret)
-		return ret;
 
 	if (priv->enabled == enable)
-		return len;
+		return 0;
 
 	if (enable) {
 		priv->enabled = true;
@@ -66,33 +60,30 @@
 		priv->enabled = false;
 	}
 
-	return len;
+	return 0;
 }
 
-static const struct counter_count_ext interrupt_cnt_ext[] = {
-	{
-		.name = "enable",
-		.read = interrupt_cnt_enable_read,
-		.write = interrupt_cnt_enable_write,
-	},
+static struct counter_comp interrupt_cnt_ext[] = {
+	COUNTER_COMP_ENABLE(interrupt_cnt_enable_read,
+			    interrupt_cnt_enable_write),
 };
 
 static const enum counter_synapse_action interrupt_cnt_synapse_actions[] = {
 	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
 };
 
-static int interrupt_cnt_action_get(struct counter_device *counter,
-				    struct counter_count *count,
-				    struct counter_synapse *synapse,
-				    size_t *action)
+static int interrupt_cnt_action_read(struct counter_device *counter,
+				     struct counter_count *count,
+				     struct counter_synapse *synapse,
+				     enum counter_synapse_action *action)
 {
-	*action = 0;
+	*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 
 	return 0;
 }
 
 static int interrupt_cnt_read(struct counter_device *counter,
-			      struct counter_count *count, unsigned long *val)
+			      struct counter_count *count, u64 *val)
 {
 	struct interrupt_cnt_priv *priv = counter->priv;
 
@@ -102,8 +93,7 @@
 }
 
 static int interrupt_cnt_write(struct counter_device *counter,
-			       struct counter_count *count,
-			       const unsigned long val)
+			       struct counter_count *count, const u64 val)
 {
 	struct interrupt_cnt_priv *priv = counter->priv;
 
@@ -119,11 +109,11 @@
 	COUNTER_FUNCTION_INCREASE,
 };
 
-static int interrupt_cnt_function_get(struct counter_device *counter,
-				      struct counter_count *count,
-				      size_t *function)
+static int interrupt_cnt_function_read(struct counter_device *counter,
+				       struct counter_count *count,
+				       enum counter_function *function)
 {
-	*function = 0;
+	*function = COUNTER_FUNCTION_INCREASE;
 
 	return 0;
 }
@@ -148,10 +138,10 @@
 }
 
 static const struct counter_ops interrupt_cnt_ops = {
-	.action_get = interrupt_cnt_action_get,
+	.action_read = interrupt_cnt_action_read,
 	.count_read = interrupt_cnt_read,
 	.count_write = interrupt_cnt_write,
-	.function_get = interrupt_cnt_function_get,
+	.function_read = interrupt_cnt_function_read,
 	.signal_read  = interrupt_cnt_signal_read,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/microchip-tcb-capture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/microchip-tcb-capture.c
@@ -29,31 +29,18 @@
 	int qdec_mode;
 	int num_channels;
 	int channel[2];
-	bool trig_inverted;
-};
-
-enum mchp_tc_count_function {
-	MCHP_TC_FUNCTION_INCREASE,
-	MCHP_TC_FUNCTION_QUADRATURE,
 };
 
 static const enum counter_function mchp_tc_count_functions[] = {
-	[MCHP_TC_FUNCTION_INCREASE] = COUNTER_FUNCTION_INCREASE,
-	[MCHP_TC_FUNCTION_QUADRATURE] = COUNTER_FUNCTION_QUADRATURE_X4,
-};
-
-enum mchp_tc_synapse_action {
-	MCHP_TC_SYNAPSE_ACTION_NONE = 0,
-	MCHP_TC_SYNAPSE_ACTION_RISING_EDGE,
-	MCHP_TC_SYNAPSE_ACTION_FALLING_EDGE,
-	MCHP_TC_SYNAPSE_ACTION_BOTH_EDGE
+	COUNTER_FUNCTION_INCREASE,
+	COUNTER_FUNCTION_QUADRATURE_X4,
 };
 
 static const enum counter_synapse_action mchp_tc_synapse_actions[] = {
-	[MCHP_TC_SYNAPSE_ACTION_NONE] = COUNTER_SYNAPSE_ACTION_NONE,
-	[MCHP_TC_SYNAPSE_ACTION_RISING_EDGE] = COUNTER_SYNAPSE_ACTION_RISING_EDGE,
-	[MCHP_TC_SYNAPSE_ACTION_FALLING_EDGE] = COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
-	[MCHP_TC_SYNAPSE_ACTION_BOTH_EDGE] = COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
+	COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
+	COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
+	COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
 };
 
 static struct counter_signal mchp_tc_count_signals[] = {
@@ -80,23 +67,23 @@
 	}
 };
 
-static int mchp_tc_count_function_get(struct counter_device *counter,
-				      struct counter_count *count,
-				      size_t *function)
+static int mchp_tc_count_function_read(struct counter_device *counter,
+				       struct counter_count *count,
+				       enum counter_function *function)
 {
 	struct mchp_tc_data *const priv = counter->priv;
 
 	if (priv->qdec_mode)
-		*function = MCHP_TC_FUNCTION_QUADRATURE;
+		*function = COUNTER_FUNCTION_QUADRATURE_X4;
 	else
-		*function = MCHP_TC_FUNCTION_INCREASE;
+		*function = COUNTER_FUNCTION_INCREASE;
 
 	return 0;
 }
 
-static int mchp_tc_count_function_set(struct counter_device *counter,
-				      struct counter_count *count,
-				      size_t function)
+static int mchp_tc_count_function_write(struct counter_device *counter,
+					struct counter_count *count,
+					enum counter_function function)
 {
 	struct mchp_tc_data *const priv = counter->priv;
 	u32 bmr, cmr;
@@ -108,11 +95,11 @@
 	cmr &= ~ATMEL_TC_WAVE;
 
 	switch (function) {
-	case MCHP_TC_FUNCTION_INCREASE:
+	case COUNTER_FUNCTION_INCREASE:
 		priv->qdec_mode = 0;
 		/* Set highest rate based on whether soc has gclk or not */
 		bmr &= ~(ATMEL_TC_QDEN | ATMEL_TC_POSEN);
-		if (priv->tc_cfg->has_gclk)
+		if (!priv->tc_cfg->has_gclk)
 			cmr |= ATMEL_TC_TIMER_CLOCK2;
 		else
 			cmr |= ATMEL_TC_TIMER_CLOCK1;
@@ -120,7 +107,7 @@
 		cmr |=  ATMEL_TC_CMR_MASK;
 		cmr &= ~(ATMEL_TC_ABETRG | ATMEL_TC_XC0);
 		break;
-	case MCHP_TC_FUNCTION_QUADRATURE:
+	case COUNTER_FUNCTION_QUADRATURE_X4:
 		if (!priv->tc_cfg->has_qdec)
 			return -EINVAL;
 		/* In QDEC mode settings both channels 0 and 1 are required */
@@ -166,7 +153,7 @@
 
 	regmap_read(priv->regmap, ATMEL_TC_REG(priv->channel[0], SR), &sr);
 
-	if (priv->trig_inverted)
+	if (signal->id == 1)
 		sigstatus = (sr & ATMEL_TC_MTIOB);
 	else
 		sigstatus = (sr & ATMEL_TC_MTIOA);
@@ -176,57 +163,68 @@
 	return 0;
 }
 
-static int mchp_tc_count_action_get(struct counter_device *counter,
-				    struct counter_count *count,
-				    struct counter_synapse *synapse,
-				    size_t *action)
+static int mchp_tc_count_action_read(struct counter_device *counter,
+				     struct counter_count *count,
+				     struct counter_synapse *synapse,
+				     enum counter_synapse_action *action)
 {
 	struct mchp_tc_data *const priv = counter->priv;
 	u32 cmr;
 
+	if (priv->qdec_mode) {
+		*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
+		return 0;
+	}
+
+	/* Only TIOA signal is evaluated in non-QDEC mode */
+	if (synapse->signal->id != 0) {
+		*action = COUNTER_SYNAPSE_ACTION_NONE;
+		return 0;
+	}
+
 	regmap_read(priv->regmap, ATMEL_TC_REG(priv->channel[0], CMR), &cmr);
 
 	switch (cmr & ATMEL_TC_ETRGEDG) {
 	default:
-		*action = MCHP_TC_SYNAPSE_ACTION_NONE;
+		*action = COUNTER_SYNAPSE_ACTION_NONE;
 		break;
 	case ATMEL_TC_ETRGEDG_RISING:
-		*action = MCHP_TC_SYNAPSE_ACTION_RISING_EDGE;
+		*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 		break;
 	case ATMEL_TC_ETRGEDG_FALLING:
-		*action = MCHP_TC_SYNAPSE_ACTION_FALLING_EDGE;
+		*action = COUNTER_SYNAPSE_ACTION_FALLING_EDGE;
 		break;
 	case ATMEL_TC_ETRGEDG_BOTH:
-		*action = MCHP_TC_SYNAPSE_ACTION_BOTH_EDGE;
+		*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		break;
 	}
 
 	return 0;
 }
 
-static int mchp_tc_count_action_set(struct counter_device *counter,
-				    struct counter_count *count,
-				    struct counter_synapse *synapse,
-				    size_t action)
+static int mchp_tc_count_action_write(struct counter_device *counter,
+				      struct counter_count *count,
+				      struct counter_synapse *synapse,
+				      enum counter_synapse_action action)
 {
 	struct mchp_tc_data *const priv = counter->priv;
 	u32 edge = ATMEL_TC_ETRGEDG_NONE;
 
-	/* QDEC mode is rising edge only */
-	if (priv->qdec_mode)
+	/* QDEC mode is rising edge only; only TIOA handled in non-QDEC mode */
+	if (priv->qdec_mode || synapse->signal->id != 0)
 		return -EINVAL;
 
 	switch (action) {
-	case MCHP_TC_SYNAPSE_ACTION_NONE:
+	case COUNTER_SYNAPSE_ACTION_NONE:
 		edge = ATMEL_TC_ETRGEDG_NONE;
 		break;
-	case MCHP_TC_SYNAPSE_ACTION_RISING_EDGE:
+	case COUNTER_SYNAPSE_ACTION_RISING_EDGE:
 		edge = ATMEL_TC_ETRGEDG_RISING;
 		break;
-	case MCHP_TC_SYNAPSE_ACTION_FALLING_EDGE:
+	case COUNTER_SYNAPSE_ACTION_FALLING_EDGE:
 		edge = ATMEL_TC_ETRGEDG_FALLING;
 		break;
-	case MCHP_TC_SYNAPSE_ACTION_BOTH_EDGE:
+	case COUNTER_SYNAPSE_ACTION_BOTH_EDGES:
 		edge = ATMEL_TC_ETRGEDG_BOTH;
 		break;
 	default:
@@ -240,8 +238,7 @@
 }
 
 static int mchp_tc_count_read(struct counter_device *counter,
-			      struct counter_count *count,
-			      unsigned long *val)
+			      struct counter_count *count, u64 *val)
 {
 	struct mchp_tc_data *const priv = counter->priv;
 	u32 cnt;
@@ -264,12 +261,12 @@
 };
 
 static const struct counter_ops mchp_tc_ops = {
-	.signal_read  = mchp_tc_count_signal_read,
-	.count_read   = mchp_tc_count_read,
-	.function_get = mchp_tc_count_function_get,
-	.function_set = mchp_tc_count_function_set,
-	.action_get   = mchp_tc_count_action_get,
-	.action_set   = mchp_tc_count_action_set
+	.signal_read    = mchp_tc_count_signal_read,
+	.count_read     = mchp_tc_count_read,
+	.function_read  = mchp_tc_count_function_read,
+	.function_write = mchp_tc_count_function_write,
+	.action_read    = mchp_tc_count_action_read,
+	.action_write   = mchp_tc_count_action_write
 };
 
 static const struct atmel_tcb_config tcb_rm9200_config = {
@@ -373,6 +370,25 @@
 			channel);
 	}
 
+	/* Disable Quadrature Decoder and position measure */
+	ret = regmap_update_bits(regmap, ATMEL_TC_BMR, ATMEL_TC_QDEN | ATMEL_TC_POSEN, 0);
+	if (ret)
+		return ret;
+
+	/* Setup the period capture mode */
+	ret = regmap_update_bits(regmap, ATMEL_TC_REG(priv->channel[0], CMR),
+				 ATMEL_TC_WAVE | ATMEL_TC_ABETRG | ATMEL_TC_CMR_MASK |
+				 ATMEL_TC_TCCLKS,
+				 ATMEL_TC_CMR_MASK);
+	if (ret)
+		return ret;
+
+	/* Enable clock and trigger counter */
+	ret = regmap_write(regmap, ATMEL_TC_REG(priv->channel[0], CCR),
+			   ATMEL_TC_CLKEN | ATMEL_TC_SWTRG);
+	if (ret)
+		return ret;
+
 	priv->tc_cfg = tcb_config;
 	priv->regmap = regmap;
 	priv->counter.name = dev_name(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/stm32-lptimer-cnt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/stm32-lptimer-cnt.c
@@ -17,6 +17,7 @@
 #include <linux/module.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
+#include <linux/types.h>
 
 struct stm32_lptim_cnt {
 	struct counter_device counter;
@@ -58,37 +59,43 @@
 		return 0;
 	}
 
+	ret = clk_enable(priv->clk);
+	if (ret)
+		goto disable_cnt;
+
 	/* LP timer must be enabled before writing CMP & ARR */
 	ret = regmap_write(priv->regmap, STM32_LPTIM_ARR, priv->ceiling);
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	ret = regmap_write(priv->regmap, STM32_LPTIM_CMP, 0);
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	/* ensure CMP & ARR registers are properly written */
 	ret = regmap_read_poll_timeout(priv->regmap, STM32_LPTIM_ISR, val,
-				       (val & STM32_LPTIM_CMPOK_ARROK),
+				       (val & STM32_LPTIM_CMPOK_ARROK) == STM32_LPTIM_CMPOK_ARROK,
 				       100, 1000);
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	ret = regmap_write(priv->regmap, STM32_LPTIM_ICR,
 			   STM32_LPTIM_CMPOKCF_ARROKCF);
 	if (ret)
-		return ret;
+		goto disable_clk;
 
-	ret = clk_enable(priv->clk);
-	if (ret) {
-		regmap_write(priv->regmap, STM32_LPTIM_CR, 0);
-		return ret;
-	}
 	priv->enabled = true;
 
 	/* Start LP timer in continuous mode */
 	return regmap_update_bits(priv->regmap, STM32_LPTIM_CR,
 				  STM32_LPTIM_CNTSTRT, STM32_LPTIM_CNTSTRT);
+
+disable_clk:
+	clk_disable(priv->clk);
+disable_cnt:
+	regmap_write(priv->regmap, STM32_LPTIM_CR, 0);
+
+	return ret;
 }
 
 static int stm32_lptim_setup(struct stm32_lptim_cnt *priv, int enable)
@@ -107,11 +114,7 @@
 	return regmap_update_bits(priv->regmap, STM32_LPTIM_CFGR, mask, val);
 }
 
-/**
- * enum stm32_lptim_cnt_function - enumerates LPTimer counter & encoder modes
- * @STM32_LPTIM_COUNTER_INCREASE: up count on IN1 rising, falling or both edges
- * @STM32_LPTIM_ENCODER_BOTH_EDGE: count on both edges (IN1 & IN2 quadrature)
- *
+/*
  * In non-quadrature mode, device counts up on active edge.
  * In quadrature mode, encoder counting scenarios are as follows:
  * +---------+----------+--------------------+--------------------+
@@ -129,33 +132,20 @@
  * | edges   | Low  ->  |   Up     |   Down  |   Down   |   Up    |
  * +---------+----------+----------+---------+----------+---------+
  */
-enum stm32_lptim_cnt_function {
-	STM32_LPTIM_COUNTER_INCREASE,
-	STM32_LPTIM_ENCODER_BOTH_EDGE,
-};
-
 static const enum counter_function stm32_lptim_cnt_functions[] = {
-	[STM32_LPTIM_COUNTER_INCREASE] = COUNTER_FUNCTION_INCREASE,
-	[STM32_LPTIM_ENCODER_BOTH_EDGE] = COUNTER_FUNCTION_QUADRATURE_X4,
-};
-
-enum stm32_lptim_synapse_action {
-	STM32_LPTIM_SYNAPSE_ACTION_RISING_EDGE,
-	STM32_LPTIM_SYNAPSE_ACTION_FALLING_EDGE,
-	STM32_LPTIM_SYNAPSE_ACTION_BOTH_EDGES,
-	STM32_LPTIM_SYNAPSE_ACTION_NONE,
+	COUNTER_FUNCTION_INCREASE,
+	COUNTER_FUNCTION_QUADRATURE_X4,
 };
 
 static const enum counter_synapse_action stm32_lptim_cnt_synapse_actions[] = {
-	/* Index must match with stm32_lptim_cnt_polarity[] (priv->polarity) */
-	[STM32_LPTIM_SYNAPSE_ACTION_RISING_EDGE] = COUNTER_SYNAPSE_ACTION_RISING_EDGE,
-	[STM32_LPTIM_SYNAPSE_ACTION_FALLING_EDGE] = COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
-	[STM32_LPTIM_SYNAPSE_ACTION_BOTH_EDGES] = COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
-	[STM32_LPTIM_SYNAPSE_ACTION_NONE] = COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
+	COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
+	COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
+	COUNTER_SYNAPSE_ACTION_NONE,
 };
 
 static int stm32_lptim_cnt_read(struct counter_device *counter,
-				struct counter_count *count, unsigned long *val)
+				struct counter_count *count, u64 *val)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
 	u32 cnt;
@@ -170,28 +160,28 @@
 	return 0;
 }
 
-static int stm32_lptim_cnt_function_get(struct counter_device *counter,
-					struct counter_count *count,
-					size_t *function)
+static int stm32_lptim_cnt_function_read(struct counter_device *counter,
+					 struct counter_count *count,
+					 enum counter_function *function)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
 
 	if (!priv->quadrature_mode) {
-		*function = STM32_LPTIM_COUNTER_INCREASE;
+		*function = COUNTER_FUNCTION_INCREASE;
 		return 0;
 	}
 
-	if (priv->polarity == STM32_LPTIM_SYNAPSE_ACTION_BOTH_EDGES) {
-		*function = STM32_LPTIM_ENCODER_BOTH_EDGE;
+	if (priv->polarity == STM32_LPTIM_CKPOL_BOTH_EDGES) {
+		*function = COUNTER_FUNCTION_QUADRATURE_X4;
 		return 0;
 	}
 
 	return -EINVAL;
 }
 
-static int stm32_lptim_cnt_function_set(struct counter_device *counter,
-					struct counter_count *count,
-					size_t function)
+static int stm32_lptim_cnt_function_write(struct counter_device *counter,
+					  struct counter_count *count,
+					  enum counter_function function)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
 
@@ -199,12 +189,12 @@
 		return -EBUSY;
 
 	switch (function) {
-	case STM32_LPTIM_COUNTER_INCREASE:
+	case COUNTER_FUNCTION_INCREASE:
 		priv->quadrature_mode = 0;
 		return 0;
-	case STM32_LPTIM_ENCODER_BOTH_EDGE:
+	case COUNTER_FUNCTION_QUADRATURE_X4:
 		priv->quadrature_mode = 1;
-		priv->polarity = STM32_LPTIM_SYNAPSE_ACTION_BOTH_EDGES;
+		priv->polarity = STM32_LPTIM_CKPOL_BOTH_EDGES;
 		return 0;
 	default:
 		/* should never reach this path */
@@ -212,9 +202,9 @@
 	}
 }
 
-static ssize_t stm32_lptim_cnt_enable_read(struct counter_device *counter,
-					   struct counter_count *count,
-					   void *private, char *buf)
+static int stm32_lptim_cnt_enable_read(struct counter_device *counter,
+				       struct counter_count *count,
+				       u8 *enable)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
 	int ret;
@@ -223,22 +213,18 @@
 	if (ret < 0)
 		return ret;
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n", ret);
+	*enable = ret;
+
+	return 0;
 }
 
-static ssize_t stm32_lptim_cnt_enable_write(struct counter_device *counter,
-					    struct counter_count *count,
-					    void *private,
-					    const char *buf, size_t len)
+static int stm32_lptim_cnt_enable_write(struct counter_device *counter,
+					struct counter_count *count,
+					u8 enable)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
-	bool enable;
 	int ret;
 
-	ret = kstrtobool(buf, &enable);
-	if (ret)
-		return ret;
-
 	/* Check nobody uses the timer, or already disabled/enabled */
 	ret = stm32_lptim_is_enabled(priv);
 	if ((ret < 0) || (!ret && !enable))
@@ -254,78 +240,81 @@
 	if (ret)
 		return ret;
 
-	return len;
+	return 0;
 }
 
-static ssize_t stm32_lptim_cnt_ceiling_read(struct counter_device *counter,
-					    struct counter_count *count,
-					    void *private, char *buf)
+static int stm32_lptim_cnt_ceiling_read(struct counter_device *counter,
+					struct counter_count *count,
+					u64 *ceiling)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", priv->ceiling);
+	*ceiling = priv->ceiling;
+
+	return 0;
 }
 
-static ssize_t stm32_lptim_cnt_ceiling_write(struct counter_device *counter,
-					     struct counter_count *count,
-					     void *private,
-					     const char *buf, size_t len)
+static int stm32_lptim_cnt_ceiling_write(struct counter_device *counter,
+					 struct counter_count *count,
+					 u64 ceiling)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
-	unsigned int ceiling;
-	int ret;
 
 	if (stm32_lptim_is_enabled(priv))
 		return -EBUSY;
 
-	ret = kstrtouint(buf, 0, &ceiling);
-	if (ret)
-		return ret;
-
 	if (ceiling > STM32_LPTIM_MAX_ARR)
 		return -ERANGE;
 
 	priv->ceiling = ceiling;
 
-	return len;
+	return 0;
 }
 
-static const struct counter_count_ext stm32_lptim_cnt_ext[] = {
-	{
-		.name = "enable",
-		.read = stm32_lptim_cnt_enable_read,
-		.write = stm32_lptim_cnt_enable_write
-	},
-	{
-		.name = "ceiling",
-		.read = stm32_lptim_cnt_ceiling_read,
-		.write = stm32_lptim_cnt_ceiling_write
-	},
+static struct counter_comp stm32_lptim_cnt_ext[] = {
+	COUNTER_COMP_ENABLE(stm32_lptim_cnt_enable_read,
+			    stm32_lptim_cnt_enable_write),
+	COUNTER_COMP_CEILING(stm32_lptim_cnt_ceiling_read,
+			     stm32_lptim_cnt_ceiling_write),
 };
 
-static int stm32_lptim_cnt_action_get(struct counter_device *counter,
-				      struct counter_count *count,
-				      struct counter_synapse *synapse,
-				      size_t *action)
+static int stm32_lptim_cnt_action_read(struct counter_device *counter,
+				       struct counter_count *count,
+				       struct counter_synapse *synapse,
+				       enum counter_synapse_action *action)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
-	size_t function;
+	enum counter_function function;
 	int err;
 
-	err = stm32_lptim_cnt_function_get(counter, count, &function);
+	err = stm32_lptim_cnt_function_read(counter, count, &function);
 	if (err)
 		return err;
 
 	switch (function) {
-	case STM32_LPTIM_COUNTER_INCREASE:
+	case COUNTER_FUNCTION_INCREASE:
 		/* LP Timer acts as up-counter on input 1 */
-		if (synapse->signal->id == count->synapses[0].signal->id)
-			*action = priv->polarity;
-		else
-			*action = STM32_LPTIM_SYNAPSE_ACTION_NONE;
-		return 0;
-	case STM32_LPTIM_ENCODER_BOTH_EDGE:
-		*action = priv->polarity;
+		if (synapse->signal->id != count->synapses[0].signal->id) {
+			*action = COUNTER_SYNAPSE_ACTION_NONE;
+			return 0;
+		}
+
+		switch (priv->polarity) {
+		case STM32_LPTIM_CKPOL_RISING_EDGE:
+			*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
+			return 0;
+		case STM32_LPTIM_CKPOL_FALLING_EDGE:
+			*action = COUNTER_SYNAPSE_ACTION_FALLING_EDGE;
+			return 0;
+		case STM32_LPTIM_CKPOL_BOTH_EDGES:
+			*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
+			return 0;
+		default:
+			/* should never reach this path */
+			return -EINVAL;
+		}
+	case COUNTER_FUNCTION_QUADRATURE_X4:
+		*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		return 0;
 	default:
 		/* should never reach this path */
@@ -333,43 +322,48 @@
 	}
 }
 
-static int stm32_lptim_cnt_action_set(struct counter_device *counter,
-				      struct counter_count *count,
-				      struct counter_synapse *synapse,
-				      size_t action)
+static int stm32_lptim_cnt_action_write(struct counter_device *counter,
+					struct counter_count *count,
+					struct counter_synapse *synapse,
+					enum counter_synapse_action action)
 {
 	struct stm32_lptim_cnt *const priv = counter->priv;
-	size_t function;
+	enum counter_function function;
 	int err;
 
 	if (stm32_lptim_is_enabled(priv))
 		return -EBUSY;
 
-	err = stm32_lptim_cnt_function_get(counter, count, &function);
+	err = stm32_lptim_cnt_function_read(counter, count, &function);
 	if (err)
 		return err;
 
 	/* only set polarity when in counter mode (on input 1) */
-	if (function == STM32_LPTIM_COUNTER_INCREASE
-	    && synapse->signal->id == count->synapses[0].signal->id) {
-		switch (action) {
-		case STM32_LPTIM_SYNAPSE_ACTION_RISING_EDGE:
-		case STM32_LPTIM_SYNAPSE_ACTION_FALLING_EDGE:
-		case STM32_LPTIM_SYNAPSE_ACTION_BOTH_EDGES:
-			priv->polarity = action;
-			return 0;
-		}
-	}
+	if (function != COUNTER_FUNCTION_INCREASE
+	    || synapse->signal->id != count->synapses[0].signal->id)
+		return -EINVAL;
 
-	return -EINVAL;
+	switch (action) {
+	case COUNTER_SYNAPSE_ACTION_RISING_EDGE:
+		priv->polarity = STM32_LPTIM_CKPOL_RISING_EDGE;
+		return 0;
+	case COUNTER_SYNAPSE_ACTION_FALLING_EDGE:
+		priv->polarity = STM32_LPTIM_CKPOL_FALLING_EDGE;
+		return 0;
+	case COUNTER_SYNAPSE_ACTION_BOTH_EDGES:
+		priv->polarity = STM32_LPTIM_CKPOL_BOTH_EDGES;
+		return 0;
+	default:
+		return -EINVAL;
+	}
 }
 
 static const struct counter_ops stm32_lptim_cnt_ops = {
 	.count_read = stm32_lptim_cnt_read,
-	.function_get = stm32_lptim_cnt_function_get,
-	.function_set = stm32_lptim_cnt_function_set,
-	.action_get = stm32_lptim_cnt_action_get,
-	.action_set = stm32_lptim_cnt_action_set,
+	.function_read = stm32_lptim_cnt_function_read,
+	.function_write = stm32_lptim_cnt_function_write,
+	.action_read = stm32_lptim_cnt_action_read,
+	.action_write = stm32_lptim_cnt_action_write,
 };
 
 static struct counter_signal stm32_lptim_cnt_signals[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/stm32-timer-cnt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/stm32-timer-cnt.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
+#include <linux/types.h>
 
 #define TIM_CCMR_CCXS	(BIT(8) | BIT(0))
 #define TIM_CCMR_MASK	(TIM_CCMR_CC1S | TIM_CCMR_CC2S | \
@@ -36,29 +37,15 @@
 	struct stm32_timer_regs bak;
 };
 
-/**
- * enum stm32_count_function - enumerates stm32 timer counter encoder modes
- * @STM32_COUNT_SLAVE_MODE_DISABLED: counts on internal clock when CEN=1
- * @STM32_COUNT_ENCODER_MODE_1: counts TI1FP1 edges, depending on TI2FP2 level
- * @STM32_COUNT_ENCODER_MODE_2: counts TI2FP2 edges, depending on TI1FP1 level
- * @STM32_COUNT_ENCODER_MODE_3: counts on both TI1FP1 and TI2FP2 edges
- */
-enum stm32_count_function {
-	STM32_COUNT_SLAVE_MODE_DISABLED,
-	STM32_COUNT_ENCODER_MODE_1,
-	STM32_COUNT_ENCODER_MODE_2,
-	STM32_COUNT_ENCODER_MODE_3,
-};
-
 static const enum counter_function stm32_count_functions[] = {
-	[STM32_COUNT_SLAVE_MODE_DISABLED] = COUNTER_FUNCTION_INCREASE,
-	[STM32_COUNT_ENCODER_MODE_1] = COUNTER_FUNCTION_QUADRATURE_X2_A,
-	[STM32_COUNT_ENCODER_MODE_2] = COUNTER_FUNCTION_QUADRATURE_X2_B,
-	[STM32_COUNT_ENCODER_MODE_3] = COUNTER_FUNCTION_QUADRATURE_X4,
+	COUNTER_FUNCTION_INCREASE,
+	COUNTER_FUNCTION_QUADRATURE_X2_A,
+	COUNTER_FUNCTION_QUADRATURE_X2_B,
+	COUNTER_FUNCTION_QUADRATURE_X4,
 };
 
 static int stm32_count_read(struct counter_device *counter,
-			    struct counter_count *count, unsigned long *val)
+			    struct counter_count *count, u64 *val)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
 	u32 cnt;
@@ -70,8 +57,7 @@
 }
 
 static int stm32_count_write(struct counter_device *counter,
-			     struct counter_count *count,
-			     const unsigned long val)
+			     struct counter_count *count, const u64 val)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
 	u32 ceiling;
@@ -83,9 +69,9 @@
 	return regmap_write(priv->regmap, TIM_CNT, val);
 }
 
-static int stm32_count_function_get(struct counter_device *counter,
-				    struct counter_count *count,
-				    size_t *function)
+static int stm32_count_function_read(struct counter_device *counter,
+				     struct counter_count *count,
+				     enum counter_function *function)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
 	u32 smcr;
@@ -93,42 +79,42 @@
 	regmap_read(priv->regmap, TIM_SMCR, &smcr);
 
 	switch (smcr & TIM_SMCR_SMS) {
-	case 0:
-		*function = STM32_COUNT_SLAVE_MODE_DISABLED;
+	case TIM_SMCR_SMS_SLAVE_MODE_DISABLED:
+		*function = COUNTER_FUNCTION_INCREASE;
 		return 0;
-	case 1:
-		*function = STM32_COUNT_ENCODER_MODE_1;
+	case TIM_SMCR_SMS_ENCODER_MODE_1:
+		*function = COUNTER_FUNCTION_QUADRATURE_X2_A;
 		return 0;
-	case 2:
-		*function = STM32_COUNT_ENCODER_MODE_2;
+	case TIM_SMCR_SMS_ENCODER_MODE_2:
+		*function = COUNTER_FUNCTION_QUADRATURE_X2_B;
 		return 0;
-	case 3:
-		*function = STM32_COUNT_ENCODER_MODE_3;
+	case TIM_SMCR_SMS_ENCODER_MODE_3:
+		*function = COUNTER_FUNCTION_QUADRATURE_X4;
 		return 0;
 	default:
 		return -EINVAL;
 	}
 }
 
-static int stm32_count_function_set(struct counter_device *counter,
-				    struct counter_count *count,
-				    size_t function)
+static int stm32_count_function_write(struct counter_device *counter,
+				      struct counter_count *count,
+				      enum counter_function function)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
 	u32 cr1, sms;
 
 	switch (function) {
-	case STM32_COUNT_SLAVE_MODE_DISABLED:
-		sms = 0;
+	case COUNTER_FUNCTION_INCREASE:
+		sms = TIM_SMCR_SMS_SLAVE_MODE_DISABLED;
 		break;
-	case STM32_COUNT_ENCODER_MODE_1:
-		sms = 1;
+	case COUNTER_FUNCTION_QUADRATURE_X2_A:
+		sms = TIM_SMCR_SMS_ENCODER_MODE_1;
 		break;
-	case STM32_COUNT_ENCODER_MODE_2:
-		sms = 2;
+	case COUNTER_FUNCTION_QUADRATURE_X2_B:
+		sms = TIM_SMCR_SMS_ENCODER_MODE_2;
 		break;
-	case STM32_COUNT_ENCODER_MODE_3:
-		sms = 3;
+	case COUNTER_FUNCTION_QUADRATURE_X4:
+		sms = TIM_SMCR_SMS_ENCODER_MODE_3;
 		break;
 	default:
 		return -EINVAL;
@@ -150,44 +136,37 @@
 	return 0;
 }
 
-static ssize_t stm32_count_direction_read(struct counter_device *counter,
+static int stm32_count_direction_read(struct counter_device *counter,
 				      struct counter_count *count,
-				      void *private, char *buf)
+				      enum counter_count_direction *direction)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
-	const char *direction;
 	u32 cr1;
 
 	regmap_read(priv->regmap, TIM_CR1, &cr1);
-	direction = (cr1 & TIM_CR1_DIR) ? "backward" : "forward";
+	*direction = (cr1 & TIM_CR1_DIR) ? COUNTER_COUNT_DIRECTION_BACKWARD :
+		COUNTER_COUNT_DIRECTION_FORWARD;
 
-	return scnprintf(buf, PAGE_SIZE, "%s\n", direction);
+	return 0;
 }
 
-static ssize_t stm32_count_ceiling_read(struct counter_device *counter,
-					struct counter_count *count,
-					void *private, char *buf)
+static int stm32_count_ceiling_read(struct counter_device *counter,
+				    struct counter_count *count, u64 *ceiling)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
 	u32 arr;
 
 	regmap_read(priv->regmap, TIM_ARR, &arr);
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", arr);
+	*ceiling = arr;
+
+	return 0;
 }
 
-static ssize_t stm32_count_ceiling_write(struct counter_device *counter,
-					 struct counter_count *count,
-					 void *private,
-					 const char *buf, size_t len)
+static int stm32_count_ceiling_write(struct counter_device *counter,
+				     struct counter_count *count, u64 ceiling)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
-	unsigned int ceiling;
-	int ret;
-
-	ret = kstrtouint(buf, 0, &ceiling);
-	if (ret)
-		return ret;
 
 	if (ceiling > priv->max_arr)
 		return -ERANGE;
@@ -196,39 +175,38 @@
 	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
 	regmap_write(priv->regmap, TIM_ARR, ceiling);
 
-	return len;
+	return 0;
 }
 
-static ssize_t stm32_count_enable_read(struct counter_device *counter,
-				       struct counter_count *count,
-				       void *private, char *buf)
+static int stm32_count_enable_read(struct counter_device *counter,
+				   struct counter_count *count, u8 *enable)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
 	u32 cr1;
 
 	regmap_read(priv->regmap, TIM_CR1, &cr1);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n", (bool)(cr1 & TIM_CR1_CEN));
+	*enable = cr1 & TIM_CR1_CEN;
+
+	return 0;
 }
 
-static ssize_t stm32_count_enable_write(struct counter_device *counter,
-					struct counter_count *count,
-					void *private,
-					const char *buf, size_t len)
+static int stm32_count_enable_write(struct counter_device *counter,
+				    struct counter_count *count, u8 enable)
 {
 	struct stm32_timer_cnt *const priv = counter->priv;
-	int err;
 	u32 cr1;
-	bool enable;
-
-	err = kstrtobool(buf, &enable);
-	if (err)
-		return err;
+	int ret;
 
 	if (enable) {
 		regmap_read(priv->regmap, TIM_CR1, &cr1);
-		if (!(cr1 & TIM_CR1_CEN))
-			clk_enable(priv->clk);
+		if (!(cr1 & TIM_CR1_CEN)) {
+			ret = clk_enable(priv->clk);
+			if (ret) {
+				dev_err(counter->parent, "Cannot enable clock %d\n", ret);
+				return ret;
+			}
+		}
 
 		regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN,
 				   TIM_CR1_CEN);
@@ -242,70 +220,55 @@
 	/* Keep enabled state to properly handle low power states */
 	priv->enabled = enable;
 
-	return len;
+	return 0;
 }
 
-static const struct counter_count_ext stm32_count_ext[] = {
-	{
-		.name = "direction",
-		.read = stm32_count_direction_read,
-	},
-	{
-		.name = "enable",
-		.read = stm32_count_enable_read,
-		.write = stm32_count_enable_write
-	},
-	{
-		.name = "ceiling",
-		.read = stm32_count_ceiling_read,
-		.write = stm32_count_ceiling_write
-	},
-};
-
-enum stm32_synapse_action {
-	STM32_SYNAPSE_ACTION_NONE,
-	STM32_SYNAPSE_ACTION_BOTH_EDGES
+static struct counter_comp stm32_count_ext[] = {
+	COUNTER_COMP_DIRECTION(stm32_count_direction_read),
+	COUNTER_COMP_ENABLE(stm32_count_enable_read, stm32_count_enable_write),
+	COUNTER_COMP_CEILING(stm32_count_ceiling_read,
+			     stm32_count_ceiling_write),
 };
 
 static const enum counter_synapse_action stm32_synapse_actions[] = {
-	[STM32_SYNAPSE_ACTION_NONE] = COUNTER_SYNAPSE_ACTION_NONE,
-	[STM32_SYNAPSE_ACTION_BOTH_EDGES] = COUNTER_SYNAPSE_ACTION_BOTH_EDGES
+	COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_BOTH_EDGES
 };
 
-static int stm32_action_get(struct counter_device *counter,
-			    struct counter_count *count,
-			    struct counter_synapse *synapse,
-			    size_t *action)
+static int stm32_action_read(struct counter_device *counter,
+			     struct counter_count *count,
+			     struct counter_synapse *synapse,
+			     enum counter_synapse_action *action)
 {
-	size_t function;
+	enum counter_function function;
 	int err;
 
-	err = stm32_count_function_get(counter, count, &function);
+	err = stm32_count_function_read(counter, count, &function);
 	if (err)
 		return err;
 
 	switch (function) {
-	case STM32_COUNT_SLAVE_MODE_DISABLED:
+	case COUNTER_FUNCTION_INCREASE:
 		/* counts on internal clock when CEN=1 */
-		*action = STM32_SYNAPSE_ACTION_NONE;
+		*action = COUNTER_SYNAPSE_ACTION_NONE;
 		return 0;
-	case STM32_COUNT_ENCODER_MODE_1:
+	case COUNTER_FUNCTION_QUADRATURE_X2_A:
 		/* counts up/down on TI1FP1 edge depending on TI2FP2 level */
 		if (synapse->signal->id == count->synapses[0].signal->id)
-			*action = STM32_SYNAPSE_ACTION_BOTH_EDGES;
+			*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		else
-			*action = STM32_SYNAPSE_ACTION_NONE;
+			*action = COUNTER_SYNAPSE_ACTION_NONE;
 		return 0;
-	case STM32_COUNT_ENCODER_MODE_2:
+	case COUNTER_FUNCTION_QUADRATURE_X2_B:
 		/* counts up/down on TI2FP2 edge depending on TI1FP1 level */
 		if (synapse->signal->id == count->synapses[1].signal->id)
-			*action = STM32_SYNAPSE_ACTION_BOTH_EDGES;
+			*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		else
-			*action = STM32_SYNAPSE_ACTION_NONE;
+			*action = COUNTER_SYNAPSE_ACTION_NONE;
 		return 0;
-	case STM32_COUNT_ENCODER_MODE_3:
+	case COUNTER_FUNCTION_QUADRATURE_X4:
 		/* counts up/down on both TI1FP1 and TI2FP2 edges */
-		*action = STM32_SYNAPSE_ACTION_BOTH_EDGES;
+		*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		return 0;
 	default:
 		return -EINVAL;
@@ -315,9 +278,9 @@
 static const struct counter_ops stm32_timer_cnt_ops = {
 	.count_read = stm32_count_read,
 	.count_write = stm32_count_write,
-	.function_get = stm32_count_function_get,
-	.function_set = stm32_count_function_set,
-	.action_get = stm32_action_get,
+	.function_read = stm32_count_function_read,
+	.function_write = stm32_count_function_write,
+	.action_read = stm32_action_read,
 };
 
 static struct counter_signal stm32_signals[] = {
@@ -417,7 +380,11 @@
 		return ret;
 
 	if (priv->enabled) {
-		clk_enable(priv->clk);
+		ret = clk_enable(priv->clk);
+		if (ret) {
+			dev_err(dev, "Cannot enable clock %d\n", ret);
+			return ret;
+		}
 
 		/* Restore registers that may have been lost */
 		regmap_write(priv->regmap, TIM_SMCR, priv->bak.smcr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/counter/ti-eqep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/counter/ti-eqep.c
@@ -13,6 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
+#include <linux/types.h>
 
 /* 32-bit registers */
 #define QPOSCNT		0x0
@@ -73,19 +74,13 @@
 };
 
 /* Position Counter Input Modes */
-enum {
+enum ti_eqep_count_func {
 	TI_EQEP_COUNT_FUNC_QUAD_COUNT,
 	TI_EQEP_COUNT_FUNC_DIR_COUNT,
 	TI_EQEP_COUNT_FUNC_UP_COUNT,
 	TI_EQEP_COUNT_FUNC_DOWN_COUNT,
 };
 
-enum {
-	TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES,
-	TI_EQEP_SYNAPSE_ACTION_RISING_EDGE,
-	TI_EQEP_SYNAPSE_ACTION_NONE,
-};
-
 struct ti_eqep_cnt {
 	struct counter_device counter;
 	struct regmap *regmap32;
@@ -93,7 +88,7 @@
 };
 
 static int ti_eqep_count_read(struct counter_device *counter,
-			      struct counter_count *count, unsigned long *val)
+			      struct counter_count *count, u64 *val)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
 	u32 cnt;
@@ -105,7 +100,7 @@
 }
 
 static int ti_eqep_count_write(struct counter_device *counter,
-			       struct counter_count *count, unsigned long val)
+			       struct counter_count *count, u64 val)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
 	u32 max;
@@ -117,64 +112,100 @@
 	return regmap_write(priv->regmap32, QPOSCNT, val);
 }
 
-static int ti_eqep_function_get(struct counter_device *counter,
-				struct counter_count *count, size_t *function)
+static int ti_eqep_function_read(struct counter_device *counter,
+				 struct counter_count *count,
+				 enum counter_function *function)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
 	u32 qdecctl;
 
 	regmap_read(priv->regmap16, QDECCTL, &qdecctl);
-	*function = (qdecctl & QDECCTL_QSRC) >> QDECCTL_QSRC_SHIFT;
+
+	switch ((qdecctl & QDECCTL_QSRC) >> QDECCTL_QSRC_SHIFT) {
+	case TI_EQEP_COUNT_FUNC_QUAD_COUNT:
+		*function = COUNTER_FUNCTION_QUADRATURE_X4;
+		break;
+	case TI_EQEP_COUNT_FUNC_DIR_COUNT:
+		*function = COUNTER_FUNCTION_PULSE_DIRECTION;
+		break;
+	case TI_EQEP_COUNT_FUNC_UP_COUNT:
+		*function = COUNTER_FUNCTION_INCREASE;
+		break;
+	case TI_EQEP_COUNT_FUNC_DOWN_COUNT:
+		*function = COUNTER_FUNCTION_DECREASE;
+		break;
+	}
 
 	return 0;
 }
 
-static int ti_eqep_function_set(struct counter_device *counter,
-				struct counter_count *count, size_t function)
+static int ti_eqep_function_write(struct counter_device *counter,
+				  struct counter_count *count,
+				  enum counter_function function)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
+	enum ti_eqep_count_func qsrc;
+
+	switch (function) {
+	case COUNTER_FUNCTION_QUADRATURE_X4:
+		qsrc = TI_EQEP_COUNT_FUNC_QUAD_COUNT;
+		break;
+	case COUNTER_FUNCTION_PULSE_DIRECTION:
+		qsrc = TI_EQEP_COUNT_FUNC_DIR_COUNT;
+		break;
+	case COUNTER_FUNCTION_INCREASE:
+		qsrc = TI_EQEP_COUNT_FUNC_UP_COUNT;
+		break;
+	case COUNTER_FUNCTION_DECREASE:
+		qsrc = TI_EQEP_COUNT_FUNC_DOWN_COUNT;
+		break;
+	default:
+		/* should never reach this path */
+		return -EINVAL;
+	}
 
 	return regmap_write_bits(priv->regmap16, QDECCTL, QDECCTL_QSRC,
-				 function << QDECCTL_QSRC_SHIFT);
+				 qsrc << QDECCTL_QSRC_SHIFT);
 }
 
-static int ti_eqep_action_get(struct counter_device *counter,
-			      struct counter_count *count,
-			      struct counter_synapse *synapse, size_t *action)
+static int ti_eqep_action_read(struct counter_device *counter,
+			       struct counter_count *count,
+			       struct counter_synapse *synapse,
+			       enum counter_synapse_action *action)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
-	size_t function;
+	enum counter_function function;
 	u32 qdecctl;
 	int err;
 
-	err = ti_eqep_function_get(counter, count, &function);
+	err = ti_eqep_function_read(counter, count, &function);
 	if (err)
 		return err;
 
 	switch (function) {
-	case TI_EQEP_COUNT_FUNC_QUAD_COUNT:
+	case COUNTER_FUNCTION_QUADRATURE_X4:
 		/* In quadrature mode, the rising and falling edge of both
 		 * QEPA and QEPB trigger QCLK.
 		 */
-		*action = TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES;
+		*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 		return 0;
-	case TI_EQEP_COUNT_FUNC_DIR_COUNT:
+	case COUNTER_FUNCTION_PULSE_DIRECTION:
 		/* In direction-count mode only rising edge of QEPA is counted
 		 * and QEPB gives direction.
 		 */
 		switch (synapse->signal->id) {
 		case TI_EQEP_SIGNAL_QEPA:
-			*action = TI_EQEP_SYNAPSE_ACTION_RISING_EDGE;
+			*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 			return 0;
 		case TI_EQEP_SIGNAL_QEPB:
-			*action = TI_EQEP_SYNAPSE_ACTION_NONE;
+			*action = COUNTER_SYNAPSE_ACTION_NONE;
 			return 0;
 		default:
 			/* should never reach this path */
 			return -EINVAL;
 		}
-	case TI_EQEP_COUNT_FUNC_UP_COUNT:
-	case TI_EQEP_COUNT_FUNC_DOWN_COUNT:
+	case COUNTER_FUNCTION_INCREASE:
+	case COUNTER_FUNCTION_DECREASE:
 		/* In up/down-count modes only QEPA is counted and QEPB is not
 		 * used.
 		 */
@@ -185,12 +216,12 @@
 				return err;
 
 			if (qdecctl & QDECCTL_XCR)
-				*action = TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES;
+				*action = COUNTER_SYNAPSE_ACTION_BOTH_EDGES;
 			else
-				*action = TI_EQEP_SYNAPSE_ACTION_RISING_EDGE;
+				*action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
 			return 0;
 		case TI_EQEP_SIGNAL_QEPB:
-			*action = TI_EQEP_SYNAPSE_ACTION_NONE;
+			*action = COUNTER_SYNAPSE_ACTION_NONE;
 			return 0;
 		default:
 			/* should never reach this path */
@@ -205,82 +236,67 @@
 static const struct counter_ops ti_eqep_counter_ops = {
 	.count_read	= ti_eqep_count_read,
 	.count_write	= ti_eqep_count_write,
-	.function_get	= ti_eqep_function_get,
-	.function_set	= ti_eqep_function_set,
-	.action_get	= ti_eqep_action_get,
+	.function_read	= ti_eqep_function_read,
+	.function_write	= ti_eqep_function_write,
+	.action_read	= ti_eqep_action_read,
 };
 
-static ssize_t ti_eqep_position_ceiling_read(struct counter_device *counter,
-					     struct counter_count *count,
-					     void *ext_priv, char *buf)
+static int ti_eqep_position_ceiling_read(struct counter_device *counter,
+					 struct counter_count *count,
+					 u64 *ceiling)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
 	u32 qposmax;
 
 	regmap_read(priv->regmap32, QPOSMAX, &qposmax);
 
-	return sprintf(buf, "%u\n", qposmax);
+	*ceiling = qposmax;
+
+	return 0;
 }
 
-static ssize_t ti_eqep_position_ceiling_write(struct counter_device *counter,
-					      struct counter_count *count,
-					      void *ext_priv, const char *buf,
-					      size_t len)
+static int ti_eqep_position_ceiling_write(struct counter_device *counter,
+					  struct counter_count *count,
+					  u64 ceiling)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
-	int err;
-	u32 res;
 
-	err = kstrtouint(buf, 0, &res);
-	if (err < 0)
-		return err;
+	if (ceiling != (u32)ceiling)
+		return -ERANGE;
 
-	regmap_write(priv->regmap32, QPOSMAX, res);
+	regmap_write(priv->regmap32, QPOSMAX, ceiling);
 
-	return len;
+	return 0;
 }
 
-static ssize_t ti_eqep_position_enable_read(struct counter_device *counter,
-					    struct counter_count *count,
-					    void *ext_priv, char *buf)
+static int ti_eqep_position_enable_read(struct counter_device *counter,
+					struct counter_count *count, u8 *enable)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
 	u32 qepctl;
 
 	regmap_read(priv->regmap16, QEPCTL, &qepctl);
 
-	return sprintf(buf, "%u\n", !!(qepctl & QEPCTL_PHEN));
+	*enable = !!(qepctl & QEPCTL_PHEN);
+
+	return 0;
 }
 
-static ssize_t ti_eqep_position_enable_write(struct counter_device *counter,
-					     struct counter_count *count,
-					     void *ext_priv, const char *buf,
-					     size_t len)
+static int ti_eqep_position_enable_write(struct counter_device *counter,
+					 struct counter_count *count, u8 enable)
 {
 	struct ti_eqep_cnt *priv = counter->priv;
-	int err;
-	bool res;
-
-	err = kstrtobool(buf, &res);
-	if (err < 0)
-		return err;
 
-	regmap_write_bits(priv->regmap16, QEPCTL, QEPCTL_PHEN, res ? -1 : 0);
+	regmap_write_bits(priv->regmap16, QEPCTL, QEPCTL_PHEN, enable ? -1 : 0);
 
-	return len;
+	return 0;
 }
 
-static struct counter_count_ext ti_eqep_position_ext[] = {
-	{
-		.name	= "ceiling",
-		.read	= ti_eqep_position_ceiling_read,
-		.write	= ti_eqep_position_ceiling_write,
-	},
-	{
-		.name	= "enable",
-		.read	= ti_eqep_position_enable_read,
-		.write	= ti_eqep_position_enable_write,
-	},
+static struct counter_comp ti_eqep_position_ext[] = {
+	COUNTER_COMP_CEILING(ti_eqep_position_ceiling_read,
+			     ti_eqep_position_ceiling_write),
+	COUNTER_COMP_ENABLE(ti_eqep_position_enable_read,
+			    ti_eqep_position_enable_write),
 };
 
 static struct counter_signal ti_eqep_signals[] = {
@@ -295,16 +311,16 @@
 };
 
 static const enum counter_function ti_eqep_position_functions[] = {
-	[TI_EQEP_COUNT_FUNC_QUAD_COUNT]	= COUNTER_FUNCTION_QUADRATURE_X4,
-	[TI_EQEP_COUNT_FUNC_DIR_COUNT]	= COUNTER_FUNCTION_PULSE_DIRECTION,
-	[TI_EQEP_COUNT_FUNC_UP_COUNT]	= COUNTER_FUNCTION_INCREASE,
-	[TI_EQEP_COUNT_FUNC_DOWN_COUNT]	= COUNTER_FUNCTION_DECREASE,
+	COUNTER_FUNCTION_QUADRATURE_X4,
+	COUNTER_FUNCTION_PULSE_DIRECTION,
+	COUNTER_FUNCTION_INCREASE,
+	COUNTER_FUNCTION_DECREASE,
 };
 
 static const enum counter_synapse_action ti_eqep_position_synapse_actions[] = {
-	[TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES]	= COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
-	[TI_EQEP_SYNAPSE_ACTION_RISING_EDGE]	= COUNTER_SYNAPSE_ACTION_RISING_EDGE,
-	[TI_EQEP_SYNAPSE_ACTION_NONE]		= COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
+	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
+	COUNTER_SYNAPSE_ACTION_NONE,
 };
 
 static struct counter_synapse ti_eqep_position_synapses[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/Kconfig.x86
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/Kconfig.x86
@@ -34,6 +34,23 @@
 
 	  If in doubt, say N.
 
+config X86_AMD_PSTATE
+	bool "AMD Processor P-State driver"
+	depends on X86 && ACPI
+	select ACPI_PROCESSOR
+	select ACPI_CPPC_LIB if X86_64
+	select CPU_FREQ_GOV_SCHEDUTIL if SMP
+	help
+	  This driver adds a CPUFreq driver which utilizes a fine grain
+	  processor performance frequency control range instead of legacy
+	  performance levels. _CPC needs to be present in the ACPI tables
+	  of the system.
+
+	  For details, take a look at:
+	  <file:Documentation/admin-guide/pm/amd-pstate.rst>.
+
+	  If in doubt, say N.
+
 config X86_ACPI_CPUFREQ
 	tristate "ACPI Processor P-States driver"
 	depends on ACPI_PROCESSOR
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/Makefile
@@ -17,6 +17,10 @@
 obj-$(CONFIG_CPUFREQ_DT)		+= cpufreq-dt.o
 obj-$(CONFIG_CPUFREQ_DT_PLATDEV)	+= cpufreq-dt-platdev.o
 
+# Traces
+CFLAGS_amd-pstate-trace.o               := -I$(src)
+amd_pstate-y				:= amd-pstate.o amd-pstate-trace.o
+
 ##################################################################################
 # x86 drivers.
 # Link order matters. K8 is preferred to ACPI because of firmware bugs in early
@@ -25,6 +29,7 @@
 # speedstep-* is preferred over p4-clockmod.
 
 obj-$(CONFIG_X86_ACPI_CPUFREQ)		+= acpi-cpufreq.o
+obj-$(CONFIG_X86_AMD_PSTATE)		+= amd_pstate.o
 obj-$(CONFIG_X86_POWERNOW_K8)		+= powernow-k8.o
 obj-$(CONFIG_X86_PCC_CPUFREQ)		+= pcc-cpufreq.o
 obj-$(CONFIG_X86_POWERNOW_K6)		+= powernow-k6.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/acpi-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/acpi-cpufreq.c
@@ -530,15 +530,6 @@
 	free_percpu(acpi_perf_data);
 }
 
-static int cpufreq_boost_online(unsigned int cpu)
-{
-	/*
-	 * On the CPU_UP path we simply keep the boost-disable flag
-	 * in sync with the current global state.
-	 */
-	return boost_set_msr(acpi_cpufreq_driver.boost_enabled);
-}
-
 static int cpufreq_boost_down_prep(unsigned int cpu)
 {
 	/*
@@ -630,7 +621,14 @@
 #endif
 
 #ifdef CONFIG_ACPI_CPPC_LIB
-static u64 get_max_boost_ratio(unsigned int cpu)
+/*
+ * get_max_boost_ratio: Computes the max_boost_ratio as the ratio
+ * between the highest_perf and the nominal_perf.
+ *
+ * Returns the max_boost_ratio for @cpu. Returns the CPPC nominal
+ * frequency via @nominal_freq if it is non-NULL pointer.
+ */
+static u64 get_max_boost_ratio(unsigned int cpu, u64 *nominal_freq)
 {
 	struct cppc_perf_caps perf_caps;
 	u64 highest_perf, nominal_perf;
@@ -653,6 +651,9 @@
 
 	nominal_perf = perf_caps.nominal_perf;
 
+	if (nominal_freq)
+		*nominal_freq = perf_caps.nominal_freq;
+
 	if (!highest_perf || !nominal_perf) {
 		pr_debug("CPU%d: highest or nominal performance missing\n", cpu);
 		return 0;
@@ -665,8 +666,12 @@
 
 	return div_u64(highest_perf << SCHED_CAPACITY_SHIFT, nominal_perf);
 }
+
 #else
-static inline u64 get_max_boost_ratio(unsigned int cpu) { return 0; }
+static inline u64 get_max_boost_ratio(unsigned int cpu, u64 *nominal_freq)
+{
+	return 0;
+}
 #endif
 
 static int acpi_cpufreq_cpu_init(struct cpufreq_policy *policy)
@@ -676,9 +681,9 @@
 	struct acpi_cpufreq_data *data;
 	unsigned int cpu = policy->cpu;
 	struct cpuinfo_x86 *c = &cpu_data(cpu);
+	u64 max_boost_ratio, nominal_freq = 0;
 	unsigned int valid_states = 0;
 	unsigned int result = 0;
-	u64 max_boost_ratio;
 	unsigned int i;
 #ifdef CONFIG_SMP
 	static int blacklisted;
@@ -828,16 +833,20 @@
 	}
 	freq_table[valid_states].frequency = CPUFREQ_TABLE_END;
 
-	max_boost_ratio = get_max_boost_ratio(cpu);
+	max_boost_ratio = get_max_boost_ratio(cpu, &nominal_freq);
 	if (max_boost_ratio) {
-		unsigned int freq = freq_table[0].frequency;
+		unsigned int freq = nominal_freq;
 
 		/*
-		 * Because the loop above sorts the freq_table entries in the
-		 * descending order, freq is the maximum frequency in the table.
-		 * Assume that it corresponds to the CPPC nominal frequency and
-		 * use it to set cpuinfo.max_freq.
+		 * The loop above sorts the freq_table entries in the
+		 * descending order. If ACPI CPPC has not advertised
+		 * the nominal frequency (this is possible in CPPC
+		 * revisions prior to 3), then use the first entry in
+		 * the pstate table as a proxy for nominal frequency.
 		 */
+		if (!freq)
+			freq = freq_table[0].frequency;
+
 		policy->cpuinfo.max_freq = freq * max_boost_ratio >> SCHED_CAPACITY_SHIFT;
 	} else {
 		/*
@@ -892,6 +901,8 @@
 	if (perf->states[0].core_frequency * 1000 != freq_table[0].frequency)
 		pr_warn(FW_WARN "P-state 0 is not max freq\n");
 
+	set_boost(policy, acpi_cpufreq_driver.boost_enabled);
+
 	return result;
 
 err_unreg:
@@ -911,6 +922,7 @@
 
 	pr_debug("%s\n", __func__);
 
+	cpufreq_boost_down_prep(policy->cpu);
 	policy->fast_switch_possible = false;
 	policy->driver_data = NULL;
 	acpi_processor_unregister_performance(data->acpi_perf_cpu);
@@ -967,25 +979,9 @@
 	acpi_cpufreq_driver.set_boost = set_boost;
 	acpi_cpufreq_driver.boost_enabled = boost_state(0);
 
-	/*
-	 * This calls the online callback on all online cpu and forces all
-	 * MSRs to the same value.
-	 */
-	ret = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "cpufreq/acpi:online",
-				cpufreq_boost_online, cpufreq_boost_down_prep);
-	if (ret < 0) {
-		pr_err("acpi_cpufreq: failed to register hotplug callbacks\n");
-		return;
-	}
 	acpi_cpufreq_online = ret;
 }
 
-static void acpi_cpufreq_boost_exit(void)
-{
-	if (acpi_cpufreq_online > 0)
-		cpuhp_remove_state_nocalls(acpi_cpufreq_online);
-}
-
 static int __init acpi_cpufreq_init(void)
 {
 	int ret;
@@ -1027,7 +1023,6 @@
 	ret = cpufreq_register_driver(&acpi_cpufreq_driver);
 	if (ret) {
 		free_acpi_perf_data();
-		acpi_cpufreq_boost_exit();
 	}
 	return ret;
 }
@@ -1036,8 +1031,6 @@
 {
 	pr_debug("%s\n", __func__);
 
-	acpi_cpufreq_boost_exit();
-
 	cpufreq_unregister_driver(&acpi_cpufreq_driver);
 
 	free_acpi_perf_data();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/amd-pstate-trace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/amd-pstate-trace.c
@@ -0,0 +1,2 @@
+#define CREATE_TRACE_POINTS
+#include "amd-pstate-trace.h"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/amd-pstate-trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/amd-pstate-trace.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * amd-pstate-trace.h - AMD Processor P-state Frequency Driver Tracer
+ *
+ * Copyright (C) 2021 Advanced Micro Devices, Inc. All Rights Reserved.
+ *
+ * Author: Huang Rui <ray.huang@amd.com>
+ */
+
+#if !defined(_AMD_PSTATE_TRACE_H) || defined(TRACE_HEADER_MULTI_READ)
+#define _AMD_PSTATE_TRACE_H
+
+#include <linux/cpufreq.h>
+#include <linux/tracepoint.h>
+#include <linux/trace_events.h>
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM amd_cpu
+
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_FILE amd-pstate-trace
+
+#define TPS(x)  tracepoint_string(x)
+
+TRACE_EVENT(amd_pstate_perf,
+
+	TP_PROTO(unsigned long min_perf,
+		 unsigned long target_perf,
+		 unsigned long capacity,
+		 unsigned int cpu_id,
+		 bool changed,
+		 bool fast_switch
+		 ),
+
+	TP_ARGS(min_perf,
+		target_perf,
+		capacity,
+		cpu_id,
+		changed,
+		fast_switch
+		),
+
+	TP_STRUCT__entry(
+		__field(unsigned long, min_perf)
+		__field(unsigned long, target_perf)
+		__field(unsigned long, capacity)
+		__field(unsigned int, cpu_id)
+		__field(bool, changed)
+		__field(bool, fast_switch)
+		),
+
+	TP_fast_assign(
+		__entry->min_perf = min_perf;
+		__entry->target_perf = target_perf;
+		__entry->capacity = capacity;
+		__entry->cpu_id = cpu_id;
+		__entry->changed = changed;
+		__entry->fast_switch = fast_switch;
+		),
+
+	TP_printk("amd_min_perf=%lu amd_des_perf=%lu amd_max_perf=%lu cpu_id=%u changed=%s fast_switch=%s",
+		  (unsigned long)__entry->min_perf,
+		  (unsigned long)__entry->target_perf,
+		  (unsigned long)__entry->capacity,
+		  (unsigned int)__entry->cpu_id,
+		  (__entry->changed) ? "true" : "false",
+		  (__entry->fast_switch) ? "true" : "false"
+		 )
+);
+
+#endif /* _AMD_PSTATE_TRACE_H */
+
+/* This part must be outside protection */
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH .
+
+#include <trace/define_trace.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/amd-pstate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/amd-pstate.c
@@ -0,0 +1,664 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * amd-pstate.c - AMD Processor P-state Frequency Driver
+ *
+ * Copyright (C) 2021 Advanced Micro Devices, Inc. All Rights Reserved.
+ *
+ * Author: Huang Rui <ray.huang@amd.com>
+ *
+ * AMD P-State introduces a new CPU performance scaling design for AMD
+ * processors using the ACPI Collaborative Performance and Power Control (CPPC)
+ * feature which works with the AMD SMU firmware providing a finer grained
+ * frequency control range. It is to replace the legacy ACPI P-States control,
+ * allows a flexible, low-latency interface for the Linux kernel to directly
+ * communicate the performance hints to hardware.
+ *
+ * AMD P-State is supported on recent AMD Zen base CPU series include some of
+ * Zen2 and Zen3 processors. _CPC needs to be present in the ACPI tables of AMD
+ * P-State supported system. And there are two types of hardware implementations
+ * for AMD P-State: 1) Full MSR Solution and 2) Shared Memory Solution.
+ * X86_FEATURE_CPPC CPU feature flag is used to distinguish the different types.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/sched.h>
+#include <linux/cpufreq.h>
+#include <linux/compiler.h>
+#include <linux/dmi.h>
+#include <linux/slab.h>
+#include <linux/acpi.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/uaccess.h>
+#include <linux/static_call.h>
+
+#include <acpi/processor.h>
+#include <acpi/cppc_acpi.h>
+
+#include <asm/msr.h>
+#include <asm/processor.h>
+#include <asm/cpufeature.h>
+#include <asm/cpu_device_id.h>
+#include "amd-pstate-trace.h"
+
+#define AMD_PSTATE_TRANSITION_LATENCY	0x20000
+#define AMD_PSTATE_TRANSITION_DELAY	500
+
+/*
+ * TODO: We need more time to fine tune processors with shared memory solution
+ * with community together.
+ *
+ * There are some performance drops on the CPU benchmarks which reports from
+ * Suse. We are co-working with them to fine tune the shared memory solution. So
+ * we disable it by default to go acpi-cpufreq on these processors and add a
+ * module parameter to be able to enable it manually for debugging.
+ */
+static struct cpufreq_driver amd_pstate_driver;
+static int cppc_load __initdata;
+
+/**
+ * struct amd_cpudata - private CPU data for AMD P-State
+ * @cpu: CPU number
+ * @req: constraint request to apply
+ * @cppc_req_cached: cached performance request hints
+ * @highest_perf: the maximum performance an individual processor may reach,
+ *		  assuming ideal conditions
+ * @nominal_perf: the maximum sustained performance level of the processor,
+ *		  assuming ideal operating conditions
+ * @lowest_nonlinear_perf: the lowest performance level at which nonlinear power
+ *			   savings are achieved
+ * @lowest_perf: the absolute lowest performance level of the processor
+ * @max_freq: the frequency that mapped to highest_perf
+ * @min_freq: the frequency that mapped to lowest_perf
+ * @nominal_freq: the frequency that mapped to nominal_perf
+ * @lowest_nonlinear_freq: the frequency that mapped to lowest_nonlinear_perf
+ * @boost_supported: check whether the Processor or SBIOS supports boost mode
+ *
+ * The amd_cpudata is key private data for each CPU thread in AMD P-State, and
+ * represents all the attributes and goals that AMD P-State requests at runtime.
+ */
+struct amd_cpudata {
+	int	cpu;
+
+	struct	freq_qos_request req[2];
+	u64	cppc_req_cached;
+
+	u32	highest_perf;
+	u32	nominal_perf;
+	u32	lowest_nonlinear_perf;
+	u32	lowest_perf;
+
+	u32	max_freq;
+	u32	min_freq;
+	u32	nominal_freq;
+	u32	lowest_nonlinear_freq;
+
+	bool	boost_supported;
+};
+
+static inline int pstate_enable(bool enable)
+{
+	return wrmsrl_safe(MSR_AMD_CPPC_ENABLE, enable);
+}
+
+static int cppc_enable(bool enable)
+{
+	int cpu, ret = 0;
+
+	for_each_present_cpu(cpu) {
+		ret = cppc_set_enable(cpu, enable);
+		if (ret)
+			return ret;
+	}
+
+	return ret;
+}
+
+DEFINE_STATIC_CALL(amd_pstate_enable, pstate_enable);
+
+static inline int amd_pstate_enable(bool enable)
+{
+	return static_call(amd_pstate_enable)(enable);
+}
+
+static int pstate_init_perf(struct amd_cpudata *cpudata)
+{
+	u64 cap1;
+
+	int ret = rdmsrl_safe_on_cpu(cpudata->cpu, MSR_AMD_CPPC_CAP1,
+				     &cap1);
+	if (ret)
+		return ret;
+
+	/*
+	 * TODO: Introduce AMD specific power feature.
+	 *
+	 * CPPC entry doesn't indicate the highest performance in some ASICs.
+	 */
+	WRITE_ONCE(cpudata->highest_perf, amd_get_highest_perf());
+
+	WRITE_ONCE(cpudata->nominal_perf, AMD_CPPC_NOMINAL_PERF(cap1));
+	WRITE_ONCE(cpudata->lowest_nonlinear_perf, AMD_CPPC_LOWNONLIN_PERF(cap1));
+	WRITE_ONCE(cpudata->lowest_perf, AMD_CPPC_LOWEST_PERF(cap1));
+
+	return 0;
+}
+
+static int cppc_init_perf(struct amd_cpudata *cpudata)
+{
+	struct cppc_perf_caps cppc_perf;
+
+	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
+	if (ret)
+		return ret;
+
+	WRITE_ONCE(cpudata->highest_perf, amd_get_highest_perf());
+
+	WRITE_ONCE(cpudata->nominal_perf, cppc_perf.nominal_perf);
+	WRITE_ONCE(cpudata->lowest_nonlinear_perf,
+		   cppc_perf.lowest_nonlinear_perf);
+	WRITE_ONCE(cpudata->lowest_perf, cppc_perf.lowest_perf);
+
+	return 0;
+}
+
+DEFINE_STATIC_CALL(amd_pstate_init_perf, pstate_init_perf);
+
+static inline int amd_pstate_init_perf(struct amd_cpudata *cpudata)
+{
+	return static_call(amd_pstate_init_perf)(cpudata);
+}
+
+static void pstate_update_perf(struct amd_cpudata *cpudata, u32 min_perf,
+			       u32 des_perf, u32 max_perf, bool fast_switch)
+{
+	if (fast_switch)
+		wrmsrl(MSR_AMD_CPPC_REQ, READ_ONCE(cpudata->cppc_req_cached));
+	else
+		wrmsrl_on_cpu(cpudata->cpu, MSR_AMD_CPPC_REQ,
+			      READ_ONCE(cpudata->cppc_req_cached));
+}
+
+static void cppc_update_perf(struct amd_cpudata *cpudata,
+			     u32 min_perf, u32 des_perf,
+			     u32 max_perf, bool fast_switch)
+{
+	struct cppc_perf_ctrls perf_ctrls;
+
+	perf_ctrls.max_perf = max_perf;
+	perf_ctrls.min_perf = min_perf;
+	perf_ctrls.desired_perf = des_perf;
+
+	cppc_set_perf(cpudata->cpu, &perf_ctrls);
+}
+
+DEFINE_STATIC_CALL(amd_pstate_update_perf, pstate_update_perf);
+
+static inline void amd_pstate_update_perf(struct amd_cpudata *cpudata,
+					  u32 min_perf, u32 des_perf,
+					  u32 max_perf, bool fast_switch)
+{
+	static_call(amd_pstate_update_perf)(cpudata, min_perf, des_perf,
+					    max_perf, fast_switch);
+}
+
+static void amd_pstate_update(struct amd_cpudata *cpudata, u32 min_perf,
+			      u32 des_perf, u32 max_perf, bool fast_switch)
+{
+	u64 prev = READ_ONCE(cpudata->cppc_req_cached);
+	u64 value = prev;
+
+	value &= ~AMD_CPPC_MIN_PERF(~0L);
+	value |= AMD_CPPC_MIN_PERF(min_perf);
+
+	value &= ~AMD_CPPC_DES_PERF(~0L);
+	value |= AMD_CPPC_DES_PERF(des_perf);
+
+	value &= ~AMD_CPPC_MAX_PERF(~0L);
+	value |= AMD_CPPC_MAX_PERF(max_perf);
+
+	trace_amd_pstate_perf(min_perf, des_perf, max_perf,
+			      cpudata->cpu, (value != prev), fast_switch);
+
+	if (value == prev)
+		return;
+
+	WRITE_ONCE(cpudata->cppc_req_cached, value);
+
+	amd_pstate_update_perf(cpudata, min_perf, des_perf,
+			       max_perf, fast_switch);
+}
+
+static int amd_pstate_verify(struct cpufreq_policy_data *policy)
+{
+	cpufreq_verify_within_cpu_limits(policy);
+
+	return 0;
+}
+
+static int amd_pstate_target(struct cpufreq_policy *policy,
+			     unsigned int target_freq,
+			     unsigned int relation)
+{
+	struct cpufreq_freqs freqs;
+	struct amd_cpudata *cpudata = policy->driver_data;
+	unsigned long max_perf, min_perf, des_perf, cap_perf;
+
+	if (!cpudata->max_freq)
+		return -ENODEV;
+
+	cap_perf = READ_ONCE(cpudata->highest_perf);
+	min_perf = READ_ONCE(cpudata->lowest_nonlinear_perf);
+	max_perf = cap_perf;
+
+	freqs.old = policy->cur;
+	freqs.new = target_freq;
+
+	des_perf = DIV_ROUND_CLOSEST(target_freq * cap_perf,
+				     cpudata->max_freq);
+
+	cpufreq_freq_transition_begin(policy, &freqs);
+	amd_pstate_update(cpudata, min_perf, des_perf,
+			  max_perf, false);
+	cpufreq_freq_transition_end(policy, &freqs, false);
+
+	return 0;
+}
+
+static void amd_pstate_adjust_perf(unsigned int cpu,
+				   unsigned long _min_perf,
+				   unsigned long target_perf,
+				   unsigned long capacity)
+{
+	unsigned long max_perf, min_perf, des_perf,
+		      cap_perf, lowest_nonlinear_perf;
+	struct cpufreq_policy *policy = cpufreq_cpu_get(cpu);
+	struct amd_cpudata *cpudata = policy->driver_data;
+
+	cap_perf = READ_ONCE(cpudata->highest_perf);
+	lowest_nonlinear_perf = READ_ONCE(cpudata->lowest_nonlinear_perf);
+
+	des_perf = cap_perf;
+	if (target_perf < capacity)
+		des_perf = DIV_ROUND_UP(cap_perf * target_perf, capacity);
+
+	min_perf = READ_ONCE(cpudata->highest_perf);
+	if (_min_perf < capacity)
+		min_perf = DIV_ROUND_UP(cap_perf * _min_perf, capacity);
+
+	if (min_perf < lowest_nonlinear_perf)
+		min_perf = lowest_nonlinear_perf;
+
+	max_perf = cap_perf;
+	if (max_perf < min_perf)
+		max_perf = min_perf;
+
+	des_perf = clamp_t(unsigned long, des_perf, min_perf, max_perf);
+
+	amd_pstate_update(cpudata, min_perf, des_perf, max_perf, true);
+}
+
+static int amd_get_min_freq(struct amd_cpudata *cpudata)
+{
+	struct cppc_perf_caps cppc_perf;
+
+	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
+	if (ret)
+		return ret;
+
+	/* Switch to khz */
+	return cppc_perf.lowest_freq * 1000;
+}
+
+static int amd_get_max_freq(struct amd_cpudata *cpudata)
+{
+	struct cppc_perf_caps cppc_perf;
+	u32 max_perf, max_freq, nominal_freq, nominal_perf;
+	u64 boost_ratio;
+
+	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
+	if (ret)
+		return ret;
+
+	nominal_freq = cppc_perf.nominal_freq;
+	nominal_perf = READ_ONCE(cpudata->nominal_perf);
+	max_perf = READ_ONCE(cpudata->highest_perf);
+
+	boost_ratio = div_u64(max_perf << SCHED_CAPACITY_SHIFT,
+			      nominal_perf);
+
+	max_freq = nominal_freq * boost_ratio >> SCHED_CAPACITY_SHIFT;
+
+	/* Switch to khz */
+	return max_freq * 1000;
+}
+
+static int amd_get_nominal_freq(struct amd_cpudata *cpudata)
+{
+	struct cppc_perf_caps cppc_perf;
+
+	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
+	if (ret)
+		return ret;
+
+	/* Switch to khz */
+	return cppc_perf.nominal_freq * 1000;
+}
+
+static int amd_get_lowest_nonlinear_freq(struct amd_cpudata *cpudata)
+{
+	struct cppc_perf_caps cppc_perf;
+	u32 lowest_nonlinear_freq, lowest_nonlinear_perf,
+	    nominal_freq, nominal_perf;
+	u64 lowest_nonlinear_ratio;
+
+	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
+	if (ret)
+		return ret;
+
+	nominal_freq = cppc_perf.nominal_freq;
+	nominal_perf = READ_ONCE(cpudata->nominal_perf);
+
+	lowest_nonlinear_perf = cppc_perf.lowest_nonlinear_perf;
+
+	lowest_nonlinear_ratio = div_u64(lowest_nonlinear_perf << SCHED_CAPACITY_SHIFT,
+					 nominal_perf);
+
+	lowest_nonlinear_freq = nominal_freq * lowest_nonlinear_ratio >> SCHED_CAPACITY_SHIFT;
+
+	/* Switch to khz */
+	return lowest_nonlinear_freq * 1000;
+}
+
+static int amd_pstate_set_boost(struct cpufreq_policy *policy, int state)
+{
+	struct amd_cpudata *cpudata = policy->driver_data;
+	int ret;
+
+	if (!cpudata->boost_supported) {
+		pr_err("Boost mode is not supported by this processor or SBIOS\n");
+		return -EINVAL;
+	}
+
+	if (state)
+		policy->cpuinfo.max_freq = cpudata->max_freq;
+	else
+		policy->cpuinfo.max_freq = cpudata->nominal_freq;
+
+	policy->max = policy->cpuinfo.max_freq;
+
+	ret = freq_qos_update_request(&cpudata->req[1],
+				      policy->cpuinfo.max_freq);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static void amd_pstate_boost_init(struct amd_cpudata *cpudata)
+{
+	u32 highest_perf, nominal_perf;
+
+	highest_perf = READ_ONCE(cpudata->highest_perf);
+	nominal_perf = READ_ONCE(cpudata->nominal_perf);
+
+	if (highest_perf <= nominal_perf)
+		return;
+
+	cpudata->boost_supported = true;
+	amd_pstate_driver.boost_enabled = true;
+}
+
+static void amd_perf_ctl_reset(unsigned int cpu)
+{
+	wrmsrl_on_cpu(cpu, MSR_AMD_PERF_CTL, 0);
+}
+
+static int amd_pstate_cpu_init(struct cpufreq_policy *policy)
+{
+	int min_freq, max_freq, nominal_freq, lowest_nonlinear_freq, ret;
+	struct device *dev;
+	struct amd_cpudata *cpudata;
+
+	/*
+	 * Resetting PERF_CTL_MSR will put the CPU in P0 frequency,
+	 * which is ideal for initialization process.
+	 */
+	amd_perf_ctl_reset(policy->cpu);
+	dev = get_cpu_device(policy->cpu);
+	if (!dev)
+		return -ENODEV;
+
+	cpudata = kzalloc(sizeof(*cpudata), GFP_KERNEL);
+	if (!cpudata)
+		return -ENOMEM;
+
+	cpudata->cpu = policy->cpu;
+
+	ret = amd_pstate_init_perf(cpudata);
+	if (ret)
+		goto free_cpudata1;
+
+	min_freq = amd_get_min_freq(cpudata);
+	max_freq = amd_get_max_freq(cpudata);
+	nominal_freq = amd_get_nominal_freq(cpudata);
+	lowest_nonlinear_freq = amd_get_lowest_nonlinear_freq(cpudata);
+
+	if (min_freq < 0 || max_freq < 0 || min_freq > max_freq) {
+		dev_err(dev, "min_freq(%d) or max_freq(%d) value is incorrect\n",
+			min_freq, max_freq);
+		ret = -EINVAL;
+		goto free_cpudata1;
+	}
+
+	policy->cpuinfo.transition_latency = AMD_PSTATE_TRANSITION_LATENCY;
+	policy->transition_delay_us = AMD_PSTATE_TRANSITION_DELAY;
+
+	policy->min = min_freq;
+	policy->max = max_freq;
+
+	policy->cpuinfo.min_freq = min_freq;
+	policy->cpuinfo.max_freq = max_freq;
+
+	/* It will be updated by governor */
+	policy->cur = policy->cpuinfo.min_freq;
+
+	if (boot_cpu_has(X86_FEATURE_CPPC))
+		policy->fast_switch_possible = true;
+
+	ret = freq_qos_add_request(&policy->constraints, &cpudata->req[0],
+				   FREQ_QOS_MIN, policy->cpuinfo.min_freq);
+	if (ret < 0) {
+		dev_err(dev, "Failed to add min-freq constraint (%d)\n", ret);
+		goto free_cpudata1;
+	}
+
+	ret = freq_qos_add_request(&policy->constraints, &cpudata->req[1],
+				   FREQ_QOS_MAX, policy->cpuinfo.max_freq);
+	if (ret < 0) {
+		dev_err(dev, "Failed to add max-freq constraint (%d)\n", ret);
+		goto free_cpudata2;
+	}
+
+	/* Initial processor data capability frequencies */
+	cpudata->max_freq = max_freq;
+	cpudata->min_freq = min_freq;
+	cpudata->nominal_freq = nominal_freq;
+	cpudata->lowest_nonlinear_freq = lowest_nonlinear_freq;
+
+	policy->driver_data = cpudata;
+
+	amd_pstate_boost_init(cpudata);
+
+	return 0;
+
+free_cpudata2:
+	freq_qos_remove_request(&cpudata->req[0]);
+free_cpudata1:
+	kfree(cpudata);
+	return ret;
+}
+
+static int amd_pstate_cpu_exit(struct cpufreq_policy *policy)
+{
+	struct amd_cpudata *cpudata;
+
+	cpudata = policy->driver_data;
+
+	freq_qos_remove_request(&cpudata->req[1]);
+	freq_qos_remove_request(&cpudata->req[0]);
+	kfree(cpudata);
+
+	return 0;
+}
+
+/* Sysfs attributes */
+
+/*
+ * This frequency is to indicate the maximum hardware frequency.
+ * If boost is not active but supported, the frequency will be larger than the
+ * one in cpuinfo.
+ */
+static ssize_t show_amd_pstate_max_freq(struct cpufreq_policy *policy,
+					char *buf)
+{
+	int max_freq;
+	struct amd_cpudata *cpudata;
+
+	cpudata = policy->driver_data;
+
+	max_freq = amd_get_max_freq(cpudata);
+	if (max_freq < 0)
+		return max_freq;
+
+	return sprintf(&buf[0], "%u\n", max_freq);
+}
+
+static ssize_t show_amd_pstate_lowest_nonlinear_freq(struct cpufreq_policy *policy,
+						     char *buf)
+{
+	int freq;
+	struct amd_cpudata *cpudata;
+
+	cpudata = policy->driver_data;
+
+	freq = amd_get_lowest_nonlinear_freq(cpudata);
+	if (freq < 0)
+		return freq;
+
+	return sprintf(&buf[0], "%u\n", freq);
+}
+
+/*
+ * In some of ASICs, the highest_perf is not the one in the _CPC table, so we
+ * need to expose it to sysfs.
+ */
+static ssize_t show_amd_pstate_highest_perf(struct cpufreq_policy *policy,
+					    char *buf)
+{
+	u32 perf;
+	struct amd_cpudata *cpudata = policy->driver_data;
+
+	perf = READ_ONCE(cpudata->highest_perf);
+
+	return sprintf(&buf[0], "%u\n", perf);
+}
+
+cpufreq_freq_attr_ro(amd_pstate_max_freq);
+cpufreq_freq_attr_ro(amd_pstate_lowest_nonlinear_freq);
+
+cpufreq_freq_attr_ro(amd_pstate_highest_perf);
+
+static struct freq_attr *amd_pstate_attr[] = {
+	&amd_pstate_max_freq,
+	&amd_pstate_lowest_nonlinear_freq,
+	&amd_pstate_highest_perf,
+	NULL,
+};
+
+static struct cpufreq_driver amd_pstate_driver = {
+	.flags		= CPUFREQ_CONST_LOOPS | CPUFREQ_NEED_UPDATE_LIMITS,
+	.verify		= amd_pstate_verify,
+	.target		= amd_pstate_target,
+	.init		= amd_pstate_cpu_init,
+	.exit		= amd_pstate_cpu_exit,
+	.set_boost	= amd_pstate_set_boost,
+	.name		= "amd-pstate",
+	.attr           = amd_pstate_attr,
+};
+
+static int __init amd_pstate_init(void)
+{
+	int ret;
+
+	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
+		return -ENODEV;
+	/*
+	 * by default the pstate driver is disabled to load
+	 * enable the amd_pstate passive mode driver explicitly
+	 * with amd_pstate=passive in kernel command line
+	 */
+	if (!cppc_load) {
+		pr_debug("driver load is disabled, boot with amd_pstate=passive to enable this\n");
+		return -ENODEV;
+	}
+
+	if (!acpi_cpc_valid()) {
+		pr_debug("the _CPC object is not present in SBIOS\n");
+		return -ENODEV;
+	}
+
+	/* don't keep reloading if cpufreq_driver exists */
+	if (cpufreq_get_current_driver())
+		return -EEXIST;
+
+	/* capability check */
+	if (boot_cpu_has(X86_FEATURE_CPPC)) {
+		pr_debug("AMD CPPC MSR based functionality is supported\n");
+		amd_pstate_driver.adjust_perf = amd_pstate_adjust_perf;
+	} else {
+		pr_debug("AMD CPPC shared memory based functionality is supported\n");
+		static_call_update(amd_pstate_enable, cppc_enable);
+		static_call_update(amd_pstate_init_perf, cppc_init_perf);
+		static_call_update(amd_pstate_update_perf, cppc_update_perf);
+	}
+
+	/* enable amd pstate feature */
+	ret = amd_pstate_enable(true);
+	if (ret) {
+		pr_err("failed to enable amd-pstate with return %d\n", ret);
+		return ret;
+	}
+
+	ret = cpufreq_register_driver(&amd_pstate_driver);
+	if (ret)
+		pr_err("failed to register amd_pstate_driver with return %d\n",
+		       ret);
+
+	return ret;
+}
+device_initcall(amd_pstate_init);
+
+static int __init amd_pstate_param(char *str)
+{
+	if (!str)
+		return -EINVAL;
+
+	if (!strcmp(str, "disable")) {
+		cppc_load = 0;
+		pr_info("driver is explicitly disabled\n");
+	} else if (!strcmp(str, "passive"))
+		cppc_load = 1;
+
+	return 0;
+}
+early_param("amd_pstate", amd_pstate_param);
+
+MODULE_AUTHOR("Huang Rui <ray.huang@amd.com>");
+MODULE_DESCRIPTION("AMD Processor P-state Frequency Driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/amd_freq_sensitivity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/amd_freq_sensitivity.c
@@ -124,6 +124,8 @@
 	if (!pcidev) {
 		if (!boot_cpu_has(X86_FEATURE_PROC_FEEDBACK))
 			return -ENODEV;
+	} else {
+		pci_dev_put(pcidev);
 	}
 
 	if (rdmsrl_safe(MSR_AMD64_FREQ_SENSITIVITY_ACTUAL, &val))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/armada-37xx-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/armada-37xx-cpufreq.c
@@ -14,10 +14,8 @@
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/mfd/syscon.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
-#include <linux/of_address.h>
-#include <linux/of_device.h>
-#include <linux/of_irq.h>
 #include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/regmap.h>
@@ -445,7 +443,7 @@
 		return -ENODEV;
 	}
 
-	clk = clk_get(cpu_dev, 0);
+	clk = clk_get(cpu_dev, NULL);
 	if (IS_ERR(clk)) {
 		dev_err(cpu_dev, "Cannot get clock for CPU0\n");
 		return PTR_ERR(clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/brcmstb-avs-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/brcmstb-avs-cpufreq.c
@@ -434,7 +434,11 @@
 	if (ret)
 		return ERR_PTR(ret);
 
-	table = devm_kcalloc(dev, AVS_PSTATE_MAX + 1, sizeof(*table),
+	/*
+	 * We allocate space for the 5 different P-STATES AVS,
+	 * plus extra space for a terminating element.
+	 */
+	table = devm_kcalloc(dev, AVS_PSTATE_MAX + 1 + 1, sizeof(*table),
 			     GFP_KERNEL);
 	if (!table)
 		return ERR_PTR(-ENOMEM);
@@ -477,8 +481,11 @@
 static unsigned int brcm_avs_cpufreq_get(unsigned int cpu)
 {
 	struct cpufreq_policy *policy = cpufreq_cpu_get(cpu);
-	struct private_data *priv = policy->driver_data;
+	struct private_data *priv;
 
+	if (!policy)
+		return 0;
+	priv = policy->driver_data;
 	cpufreq_cpu_put(policy);
 
 	return brcm_avs_get_frequency(priv->base);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cppc_cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cppc_cpufreq.c
@@ -303,52 +303,48 @@
 
 /*
  * If CPPC lowest_freq and nominal_freq registers are exposed then we can
- * use them to convert perf to freq and vice versa
- *
- * If the perf/freq point lies between Nominal and Lowest, we can treat
- * (Low perf, Low freq) and (Nom Perf, Nom freq) as 2D co-ordinates of a line
- * and extrapolate the rest
- * For perf/freq > Nominal, we use the ratio perf:freq at Nominal for conversion
+ * use them to convert perf to freq and vice versa. The conversion is
+ * extrapolated as an affine function passing by the 2 points:
+ *  - (Low perf, Low freq)
+ *  - (Nominal perf, Nominal perf)
  */
 static unsigned int cppc_cpufreq_perf_to_khz(struct cppc_cpudata *cpu_data,
 					     unsigned int perf)
 {
 	struct cppc_perf_caps *caps = &cpu_data->perf_caps;
+	s64 retval, offset = 0;
 	static u64 max_khz;
 	u64 mul, div;
 
 	if (caps->lowest_freq && caps->nominal_freq) {
-		if (perf >= caps->nominal_perf) {
-			mul = caps->nominal_freq;
-			div = caps->nominal_perf;
-		} else {
-			mul = caps->nominal_freq - caps->lowest_freq;
-			div = caps->nominal_perf - caps->lowest_perf;
-		}
+		mul = caps->nominal_freq - caps->lowest_freq;
+		div = caps->nominal_perf - caps->lowest_perf;
+		offset = caps->nominal_freq - div64_u64(caps->nominal_perf * mul, div);
 	} else {
 		if (!max_khz)
 			max_khz = cppc_get_dmi_max_khz();
 		mul = max_khz;
 		div = caps->highest_perf;
 	}
-	return (u64)perf * mul / div;
+
+	retval = offset + div64_u64(perf * mul, div);
+	if (retval >= 0)
+		return retval;
+	return 0;
 }
 
 static unsigned int cppc_cpufreq_khz_to_perf(struct cppc_cpudata *cpu_data,
 					     unsigned int freq)
 {
 	struct cppc_perf_caps *caps = &cpu_data->perf_caps;
+	s64 retval, offset = 0;
 	static u64 max_khz;
 	u64  mul, div;
 
 	if (caps->lowest_freq && caps->nominal_freq) {
-		if (freq >= caps->nominal_freq) {
-			mul = caps->nominal_perf;
-			div = caps->nominal_freq;
-		} else {
-			mul = caps->lowest_perf;
-			div = caps->lowest_freq;
-		}
+		mul = caps->nominal_perf - caps->lowest_perf;
+		div = caps->nominal_freq - caps->lowest_freq;
+		offset = caps->nominal_perf - div64_u64(caps->nominal_freq * mul, div);
 	} else {
 		if (!max_khz)
 			max_khz = cppc_get_dmi_max_khz();
@@ -356,7 +352,10 @@
 		div = max_khz;
 	}
 
-	return (u64)freq * mul / div;
+	retval = offset + div64_u64(freq * mul, div);
+	if (retval >= 0)
+		return retval;
+	return 0;
 }
 
 static int cppc_cpufreq_set_target(struct cpufreq_policy *policy,
@@ -616,10 +615,15 @@
 {
 	struct cppc_perf_fb_ctrs fb_ctrs_t0 = {0}, fb_ctrs_t1 = {0};
 	struct cpufreq_policy *policy = cpufreq_cpu_get(cpu);
-	struct cppc_cpudata *cpu_data = policy->driver_data;
+	struct cppc_cpudata *cpu_data;
 	u64 delivered_perf;
 	int ret;
 
+	if (!policy)
+		return -ENODEV;
+
+	cpu_data = policy->driver_data;
+
 	cpufreq_cpu_put(policy);
 
 	ret = cppc_get_perf_ctrs(cpu, &fb_ctrs_t0);
@@ -698,10 +702,15 @@
 static unsigned int hisi_cppc_cpufreq_get_rate(unsigned int cpu)
 {
 	struct cpufreq_policy *policy = cpufreq_cpu_get(cpu);
-	struct cppc_cpudata *cpu_data = policy->driver_data;
+	struct cppc_cpudata *cpu_data;
 	u64 desired_perf;
 	int ret;
 
+	if (!policy)
+		return -ENODEV;
+
+	cpu_data = policy->driver_data;
+
 	cpufreq_cpu_put(policy);
 
 	ret = cppc_get_desired_perf(cpu, &desired_perf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq-dt-platdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -133,6 +133,7 @@
 	{ .compatible = "nvidia,tegra30", },
 	{ .compatible = "nvidia,tegra124", },
 	{ .compatible = "nvidia,tegra210", },
+	{ .compatible = "nvidia,tegra234", },
 
 	{ .compatible = "qcom,apq8096", },
 	{ .compatible = "qcom,msm8996", },
@@ -143,6 +144,7 @@
 	{ .compatible = "qcom,sc8180x", },
 	{ .compatible = "qcom,sdm845", },
 	{ .compatible = "qcom,sm6350", },
+	{ .compatible = "qcom,sm6375", },
 	{ .compatible = "qcom,sm8150", },
 	{ .compatible = "qcom,sm8250", },
 	{ .compatible = "qcom,sm8350", },
@@ -169,7 +171,7 @@
 	struct device_node *np = of_cpu_device_node_get(0);
 	bool ret = false;
 
-	if (of_get_property(np, "operating-points-v2", NULL))
+	if (of_property_present(np, "operating-points-v2"))
 		ret = true;
 
 	of_node_put(np);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq-dt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq-dt.c
@@ -208,7 +208,7 @@
 	if (!priv)
 		return -ENOMEM;
 
-	if (!alloc_cpumask_var(&priv->cpus, GFP_KERNEL))
+	if (!zalloc_cpumask_var(&priv->cpus, GFP_KERNEL))
 		return -ENOMEM;
 
 	cpumask_set_cpu(cpu, priv->cpus);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq.c
@@ -28,6 +28,7 @@
 #include <linux/suspend.h>
 #include <linux/syscore_ops.h>
 #include <linux/tick.h>
+#include <linux/units.h>
 #include <trace/events/power.h>
 
 static LIST_HEAD(cpufreq_policy_list);
@@ -449,8 +450,10 @@
 			    policy->cur,
 			    policy->cpuinfo.max_freq);
 
+	spin_lock(&policy->transition_lock);
 	policy->transition_ongoing = false;
 	policy->transition_task = NULL;
+	spin_unlock(&policy->transition_lock);
 
 	wake_up(&policy->transition_wait);
 }
@@ -531,7 +534,7 @@
 
 	target_freq = clamp_val(target_freq, policy->min, policy->max);
 
-	if (!cpufreq_driver->target_index)
+	if (!policy->freq_table)
 		return target_freq;
 
 	idx = cpufreq_frequency_table_target(policy, target_freq, relation);
@@ -1004,10 +1007,9 @@
 	.release	= cpufreq_sysfs_release,
 };
 
-static void add_cpu_dev_symlink(struct cpufreq_policy *policy, unsigned int cpu)
+static void add_cpu_dev_symlink(struct cpufreq_policy *policy, unsigned int cpu,
+				struct device *dev)
 {
-	struct device *dev = get_cpu_device(cpu);
-
 	if (unlikely(!dev))
 		return;
 
@@ -1212,6 +1214,7 @@
 	if (!zalloc_cpumask_var(&policy->real_cpus, GFP_KERNEL))
 		goto err_free_rcpumask;
 
+	init_completion(&policy->kobj_unregister);
 	ret = kobject_init_and_add(&policy->kobj, &ktype_cpufreq,
 				   cpufreq_global_kobject, "policy%u", cpu);
 	if (ret) {
@@ -1250,7 +1253,6 @@
 	init_rwsem(&policy->rwsem);
 	spin_lock_init(&policy->transition_lock);
 	init_waitqueue_head(&policy->transition_wait);
-	init_completion(&policy->kobj_unregister);
 	INIT_WORK(&policy->update, handle_update);
 
 	policy->cpu = cpu;
@@ -1391,7 +1393,7 @@
 	if (new_policy) {
 		for_each_cpu(j, policy->related_cpus) {
 			per_cpu(cpufreq_cpu_data, j) = policy;
-			add_cpu_dev_symlink(policy, j);
+			add_cpu_dev_symlink(policy, j, get_cpu_device(j));
 		}
 
 		policy->min_freq_req = kzalloc(2 * sizeof(*policy->min_freq_req),
@@ -1403,7 +1405,7 @@
 
 		ret = freq_qos_add_request(&policy->constraints,
 					   policy->min_freq_req, FREQ_QOS_MIN,
-					   policy->min);
+					   FREQ_QOS_MIN_DEFAULT_VALUE);
 		if (ret < 0) {
 			/*
 			 * So we don't call freq_qos_remove_request() for an
@@ -1423,7 +1425,7 @@
 
 		ret = freq_qos_add_request(&policy->constraints,
 					   policy->max_freq_req, FREQ_QOS_MAX,
-					   policy->max);
+					   FREQ_QOS_MAX_DEFAULT_VALUE);
 		if (ret < 0) {
 			policy->max_freq_req = NULL;
 			goto out_destroy_policy;
@@ -1565,52 +1567,41 @@
 	/* Create sysfs link on CPU registration */
 	policy = per_cpu(cpufreq_cpu_data, cpu);
 	if (policy)
-		add_cpu_dev_symlink(policy, cpu);
+		add_cpu_dev_symlink(policy, cpu, dev);
 
 	return 0;
 }
 
-static int cpufreq_offline(unsigned int cpu)
+static void __cpufreq_offline(unsigned int cpu, struct cpufreq_policy *policy)
 {
-	struct cpufreq_policy *policy;
 	int ret;
 
-	pr_debug("%s: unregistering CPU %u\n", __func__, cpu);
-
-	policy = cpufreq_cpu_get_raw(cpu);
-	if (!policy) {
-		pr_debug("%s: No cpu_data found\n", __func__);
-		return 0;
-	}
-
-	down_write(&policy->rwsem);
 	if (has_target())
 		cpufreq_stop_governor(policy);
 
 	cpumask_clear_cpu(cpu, policy->cpus);
 
-	if (policy_is_inactive(policy)) {
-		if (has_target())
-			strncpy(policy->last_governor, policy->governor->name,
-				CPUFREQ_NAME_LEN);
-		else
-			policy->last_policy = policy->policy;
-	} else if (cpu == policy->cpu) {
-		/* Nominate new CPU */
-		policy->cpu = cpumask_any(policy->cpus);
-	}
-
-	/* Start governor again for active policy */
 	if (!policy_is_inactive(policy)) {
+		/* Nominate a new CPU if necessary. */
+		if (cpu == policy->cpu)
+			policy->cpu = cpumask_any(policy->cpus);
+
+		/* Start the governor again for the active policy. */
 		if (has_target()) {
 			ret = cpufreq_start_governor(policy);
 			if (ret)
 				pr_err("%s: Failed to start governor\n", __func__);
 		}
 
-		goto unlock;
+		return;
 	}
 
+	if (has_target())
+		strncpy(policy->last_governor, policy->governor->name,
+			CPUFREQ_NAME_LEN);
+	else
+		policy->last_policy = policy->policy;
+
 	if (cpufreq_thermal_control_enabled(cpufreq_driver)) {
 		cpufreq_cooling_unregister(policy->cdev);
 		policy->cdev = NULL;
@@ -1625,12 +1616,31 @@
 	 */
 	if (cpufreq_driver->offline) {
 		cpufreq_driver->offline(policy);
-	} else if (cpufreq_driver->exit) {
+		return;
+	}
+
+	if (cpufreq_driver->exit)
 		cpufreq_driver->exit(policy);
-		policy->freq_table = NULL;
+
+	policy->freq_table = NULL;
+}
+
+static int cpufreq_offline(unsigned int cpu)
+{
+	struct cpufreq_policy *policy;
+
+	pr_debug("%s: unregistering CPU %u\n", __func__, cpu);
+
+	policy = cpufreq_cpu_get_raw(cpu);
+	if (!policy) {
+		pr_debug("%s: No cpu_data found\n", __func__);
+		return 0;
 	}
 
-unlock:
+	down_write(&policy->rwsem);
+
+	__cpufreq_offline(cpu, policy);
+
 	up_write(&policy->rwsem);
 	return 0;
 }
@@ -1648,19 +1658,26 @@
 	if (!policy)
 		return;
 
+	down_write(&policy->rwsem);
+
 	if (cpu_online(cpu))
-		cpufreq_offline(cpu);
+		__cpufreq_offline(cpu, policy);
 
 	cpumask_clear_cpu(cpu, policy->real_cpus);
 	remove_cpu_dev_symlink(policy, dev);
 
-	if (cpumask_empty(policy->real_cpus)) {
-		/* We did light-weight exit earlier, do full tear down now */
-		if (cpufreq_driver->offline)
-			cpufreq_driver->exit(policy);
-
-		cpufreq_policy_free(policy);
+	if (!cpumask_empty(policy->real_cpus)) {
+		up_write(&policy->rwsem);
+		return;
 	}
+
+	/* We did light-weight exit earlier, do full tear down now */
+	if (cpufreq_driver->offline && cpufreq_driver->exit)
+		cpufreq_driver->exit(policy);
+
+	up_write(&policy->rwsem);
+
+	cpufreq_policy_free(policy);
 }
 
 /**
@@ -1702,6 +1719,16 @@
 		return new_freq;
 
 	if (policy->cur != new_freq) {
+		/*
+		 * For some platforms, the frequency returned by hardware may be
+		 * slightly different from what is provided in the frequency
+		 * table, for example hardware may return 499 MHz instead of 500
+		 * MHz. In such cases it is better to avoid getting into
+		 * unnecessary frequency updates.
+		 */
+		if (abs(policy->cur - new_freq) < KHZ_PER_MHZ)
+			return policy->cur;
+
 		cpufreq_out_of_sync(policy, new_freq);
 		if (update)
 			schedule_work(&policy->update);
@@ -2523,8 +2550,15 @@
 	if (ret)
 		return ret;
 
+	/*
+	 * Resolve policy min/max to available frequencies. It ensures
+	 * no frequency resolution will neither overshoot the requested maximum
+	 * nor undershoot the requested minimum.
+	 */
 	policy->min = new_data.min;
 	policy->max = new_data.max;
+	policy->min = __resolve_freq(policy, policy->min, CPUFREQ_RELATION_L);
+	policy->max = __resolve_freq(policy, policy->max, CPUFREQ_RELATION_H);
 	trace_cpu_frequency_limits(policy);
 
 	policy->cached_target_freq = UINT_MAX;
@@ -2749,6 +2783,20 @@
 	return 0;
 }
 
+static char cpufreq_driver_name[CPUFREQ_NAME_LEN];
+
+static int __init cpufreq_driver_setup(char *str)
+{
+	strlcpy(cpufreq_driver_name, str, CPUFREQ_NAME_LEN);
+	return 1;
+}
+
+/*
+ * Set this name to only allow one specific cpu freq driver, e.g.,
+ * cpufreq_driver=powernow-k8
+ */
+__setup("cpufreq_driver=", cpufreq_driver_setup);
+
 /**
  * cpufreq_register_driver - register a CPU Frequency driver
  * @driver_data: A struct cpufreq_driver containing the values#
@@ -2783,7 +2831,13 @@
 	     (!driver_data->online != !driver_data->offline))
 		return -EINVAL;
 
-	pr_debug("trying to register driver %s\n", driver_data->name);
+	pr_debug("trying to register driver %s, cpufreq_driver=%s\n",
+		driver_data->name, cpufreq_driver_name);
+
+	if (cpufreq_driver_name[0])
+		if (!driver_data->name ||
+			strcmp(cpufreq_driver_name, driver_data->name))
+				return -EINVAL;
 
 	/* Protect against concurrent CPU online/offline. */
 	cpus_read_lock();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq_governor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq_governor.c
@@ -145,7 +145,23 @@
 		time_elapsed = update_time - j_cdbs->prev_update_time;
 		j_cdbs->prev_update_time = update_time;
 
-		idle_time = cur_idle_time - j_cdbs->prev_cpu_idle;
+		/*
+		 * cur_idle_time could be smaller than j_cdbs->prev_cpu_idle if
+		 * it's obtained from get_cpu_idle_time_jiffy() when NOHZ is
+		 * off, where idle_time is calculated by the difference between
+		 * time elapsed in jiffies and "busy time" obtained from CPU
+		 * statistics.  If a CPU is 100% busy, the time elapsed and busy
+		 * time should grow with the same amount in two consecutive
+		 * samples, but in practice there could be a tiny difference,
+		 * making the accumulated idle time decrease sometimes.  Hence,
+		 * in this case, idle_time should be regarded as 0 in order to
+		 * make the further process correct.
+		 */
+		if (cur_idle_time > j_cdbs->prev_cpu_idle)
+			idle_time = cur_idle_time - j_cdbs->prev_cpu_idle;
+		else
+			idle_time = 0;
+
 		j_cdbs->prev_cpu_idle = cur_idle_time;
 
 		if (ignore_nice) {
@@ -162,7 +178,7 @@
 			 * calls, so the previous load value can be used then.
 			 */
 			load = j_cdbs->prev_load;
-		} else if (unlikely((int)idle_time > 2 * sampling_rate &&
+		} else if (unlikely(idle_time > 2 * sampling_rate &&
 				    j_cdbs->prev_load)) {
 			/*
 			 * If the CPU had gone completely idle and a task has
@@ -189,30 +205,15 @@
 			load = j_cdbs->prev_load;
 			j_cdbs->prev_load = 0;
 		} else {
-			if (time_elapsed >= idle_time) {
+			if (time_elapsed > idle_time)
 				load = 100 * (time_elapsed - idle_time) / time_elapsed;
-			} else {
-				/*
-				 * That can happen if idle_time is returned by
-				 * get_cpu_idle_time_jiffy().  In that case
-				 * idle_time is roughly equal to the difference
-				 * between time_elapsed and "busy time" obtained
-				 * from CPU statistics.  Then, the "busy time"
-				 * can end up being greater than time_elapsed
-				 * (for example, if jiffies_64 and the CPU
-				 * statistics are updated by different CPUs),
-				 * so idle_time may in fact be negative.  That
-				 * means, though, that the CPU was busy all
-				 * the time (on the rough average) during the
-				 * last sampling interval and 100 can be
-				 * returned as the load.
-				 */
-				load = (int)idle_time < 0 ? 100 : 0;
-			}
+			else
+				load = 0;
+
 			j_cdbs->prev_load = load;
 		}
 
-		if (unlikely((int)idle_time > 2 * sampling_rate)) {
+		if (unlikely(idle_time > 2 * sampling_rate)) {
 			unsigned int periods = idle_time / sampling_rate;
 
 			if (periods < idle_periods)
@@ -388,6 +389,15 @@
 	gov->free(policy_dbs);
 }
 
+static void cpufreq_dbs_data_release(struct kobject *kobj)
+{
+	struct dbs_data *dbs_data = to_dbs_data(to_gov_attr_set(kobj));
+	struct dbs_governor *gov = dbs_data->gov;
+
+	gov->exit(dbs_data);
+	kfree(dbs_data);
+}
+
 int cpufreq_dbs_governor_init(struct cpufreq_policy *policy)
 {
 	struct dbs_governor *gov = dbs_governor_of(policy);
@@ -425,6 +435,7 @@
 		goto free_policy_dbs_info;
 	}
 
+	dbs_data->gov = gov;
 	gov_attr_set_init(&dbs_data->attr_set, &policy_dbs->list);
 
 	ret = gov->init(dbs_data);
@@ -447,6 +458,7 @@
 	policy->governor_data = policy_dbs;
 
 	gov->kobj_type.sysfs_ops = &governor_sysfs_ops;
+	gov->kobj_type.release = cpufreq_dbs_data_release;
 	ret = kobject_init_and_add(&dbs_data->attr_set.kobj, &gov->kobj_type,
 				   get_governor_parent_kobj(policy),
 				   "%s", gov->gov.name);
@@ -488,13 +500,8 @@
 
 	policy->governor_data = NULL;
 
-	if (!count) {
-		if (!have_governor_per_policy())
-			gov->gdbs_data = NULL;
-
-		gov->exit(dbs_data);
-		kfree(dbs_data);
-	}
+	if (!count && !have_governor_per_policy())
+		gov->gdbs_data = NULL;
 
 	free_policy_dbs_info(policy_dbs, gov);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq_governor.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq_governor.h
@@ -37,6 +37,7 @@
 /* Governor demand based switching data (per-policy or global). */
 struct dbs_data {
 	struct gov_attr_set attr_set;
+	struct dbs_governor *gov;
 	void *tuners;
 	unsigned int ignore_nice_load;
 	unsigned int sampling_rate;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq_governor_attr_set.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq_governor_attr_set.c
@@ -8,11 +8,6 @@
 
 #include "cpufreq_governor.h"
 
-static inline struct gov_attr_set *to_gov_attr_set(struct kobject *kobj)
-{
-	return container_of(kobj, struct gov_attr_set, kobj);
-}
-
 static inline struct governor_attr *to_gov_attr(struct attribute *attr)
 {
 	return container_of(attr, struct governor_attr, attr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/cpufreq_stats.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/cpufreq_stats.c
@@ -131,25 +131,25 @@
 	len += scnprintf(buf + len, PAGE_SIZE - len, "   From  :    To\n");
 	len += scnprintf(buf + len, PAGE_SIZE - len, "         : ");
 	for (i = 0; i < stats->state_num; i++) {
-		if (len >= PAGE_SIZE)
+		if (len >= PAGE_SIZE - 1)
 			break;
 		len += scnprintf(buf + len, PAGE_SIZE - len, "%9u ",
 				stats->freq_table[i]);
 	}
-	if (len >= PAGE_SIZE)
-		return PAGE_SIZE;
+	if (len >= PAGE_SIZE - 1)
+		return PAGE_SIZE - 1;
 
 	len += scnprintf(buf + len, PAGE_SIZE - len, "\n");
 
 	for (i = 0; i < stats->state_num; i++) {
-		if (len >= PAGE_SIZE)
+		if (len >= PAGE_SIZE - 1)
 			break;
 
 		len += scnprintf(buf + len, PAGE_SIZE - len, "%9u: ",
 				stats->freq_table[i]);
 
 		for (j = 0; j < stats->state_num; j++) {
-			if (len >= PAGE_SIZE)
+			if (len >= PAGE_SIZE - 1)
 				break;
 
 			if (pending)
@@ -159,12 +159,12 @@
 
 			len += scnprintf(buf + len, PAGE_SIZE - len, "%9u ", count);
 		}
-		if (len >= PAGE_SIZE)
+		if (len >= PAGE_SIZE - 1)
 			break;
 		len += scnprintf(buf + len, PAGE_SIZE - len, "\n");
 	}
 
-	if (len >= PAGE_SIZE) {
+	if (len >= PAGE_SIZE - 1) {
 		pr_warn_once("cpufreq transition table exceeds PAGE_SIZE. Disabling\n");
 		return -EFBIG;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/imx-cpufreq-dt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/imx-cpufreq-dt.c
@@ -89,7 +89,7 @@
 
 	cpu_dev = get_cpu_device(0);
 
-	if (!of_find_property(cpu_dev->of_node, "cpu-supply", NULL))
+	if (!of_property_present(cpu_dev->of_node, "cpu-supply"))
 		return -ENODEV;
 
 	if (of_machine_is_compatible("fsl,imx7ulp")) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/imx6q-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/imx6q-cpufreq.c
@@ -209,6 +209,14 @@
 	.suspend = cpufreq_generic_suspend,
 };
 
+static void imx6x_disable_freq_in_opp(struct device *dev, unsigned long freq)
+{
+	int ret = dev_pm_opp_disable(dev, freq);
+
+	if (ret < 0 && ret != -ENODEV)
+		dev_warn(dev, "failed to disable %ldMHz OPP\n", freq / 1000000);
+}
+
 #define OCOTP_CFG3			0x440
 #define OCOTP_CFG3_SPEED_SHIFT		16
 #define OCOTP_CFG3_SPEED_1P2GHZ		0x3
@@ -222,7 +230,7 @@
 	u32 val;
 	int ret;
 
-	if (of_find_property(dev->of_node, "nvmem-cells", NULL)) {
+	if (of_property_present(dev->of_node, "nvmem-cells")) {
 		ret = nvmem_cell_read_u32(dev, "speed_grade", &val);
 		if (ret)
 			return ret;
@@ -254,17 +262,15 @@
 	val &= 0x3;
 
 	if (val < OCOTP_CFG3_SPEED_996MHZ)
-		if (dev_pm_opp_disable(dev, 996000000))
-			dev_warn(dev, "failed to disable 996MHz OPP\n");
+		imx6x_disable_freq_in_opp(dev, 996000000);
 
 	if (of_machine_is_compatible("fsl,imx6q") ||
 	    of_machine_is_compatible("fsl,imx6qp")) {
 		if (val != OCOTP_CFG3_SPEED_852MHZ)
-			if (dev_pm_opp_disable(dev, 852000000))
-				dev_warn(dev, "failed to disable 852MHz OPP\n");
+			imx6x_disable_freq_in_opp(dev, 852000000);
+
 		if (val != OCOTP_CFG3_SPEED_1P2GHZ)
-			if (dev_pm_opp_disable(dev, 1200000000))
-				dev_warn(dev, "failed to disable 1.2GHz OPP\n");
+			imx6x_disable_freq_in_opp(dev, 1200000000);
 	}
 
 	return 0;
@@ -279,7 +285,7 @@
 	u32 val;
 	int ret = 0;
 
-	if (of_find_property(dev->of_node, "nvmem-cells", NULL)) {
+	if (of_property_present(dev->of_node, "nvmem-cells")) {
 		ret = nvmem_cell_read_u32(dev, "speed_grade", &val);
 		if (ret)
 			return ret;
@@ -316,20 +322,16 @@
 	val >>= OCOTP_CFG3_SPEED_SHIFT;
 	val &= 0x3;
 
-	if (of_machine_is_compatible("fsl,imx6ul")) {
+	if (of_machine_is_compatible("fsl,imx6ul"))
 		if (val != OCOTP_CFG3_6UL_SPEED_696MHZ)
-			if (dev_pm_opp_disable(dev, 696000000))
-				dev_warn(dev, "failed to disable 696MHz OPP\n");
-	}
+			imx6x_disable_freq_in_opp(dev, 696000000);
 
 	if (of_machine_is_compatible("fsl,imx6ull")) {
-		if (val != OCOTP_CFG3_6ULL_SPEED_792MHZ)
-			if (dev_pm_opp_disable(dev, 792000000))
-				dev_warn(dev, "failed to disable 792MHz OPP\n");
+		if (val < OCOTP_CFG3_6ULL_SPEED_792MHZ)
+			imx6x_disable_freq_in_opp(dev, 792000000);
 
 		if (val != OCOTP_CFG3_6ULL_SPEED_900MHZ)
-			if (dev_pm_opp_disable(dev, 900000000))
-				dev_warn(dev, "failed to disable 900MHz OPP\n");
+			imx6x_disable_freq_in_opp(dev, 900000000);
 	}
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/intel_pstate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/intel_pstate.c
@@ -27,6 +27,7 @@
 #include <linux/pm_qos.h>
 #include <trace/events/power.h>
 
+#include <asm/cpu.h>
 #include <asm/div64.h>
 #include <asm/msr.h>
 #include <asm/cpu_device_id.h>
@@ -277,10 +278,10 @@
  * structure is used to store those callbacks.
  */
 struct pstate_funcs {
-	int (*get_max)(void);
-	int (*get_max_physical)(void);
-	int (*get_min)(void);
-	int (*get_turbo)(void);
+	int (*get_max)(int cpu);
+	int (*get_max_physical)(int cpu);
+	int (*get_min)(int cpu);
+	int (*get_turbo)(int cpu);
 	int (*get_scaling)(void);
 	int (*get_cpu_scaling)(int cpu);
 	int (*get_aperf_mperf_shift)(void);
@@ -297,6 +298,13 @@
 
 static struct cpufreq_driver *intel_pstate_driver __read_mostly;
 
+#define HYBRID_SCALING_FACTOR	78741
+
+static inline int core_get_scaling(void)
+{
+	return 100000;
+}
+
 #ifdef CONFIG_ACPI
 static bool acpi_ppc;
 #endif
@@ -335,6 +343,8 @@
 
 static DECLARE_WORK(sched_itmt_work, intel_pstste_sched_itmt_work_fn);
 
+#define CPPC_MAX_PERF	U8_MAX
+
 static void intel_pstate_set_itmt_prio(int cpu)
 {
 	struct cppc_perf_caps cppc_perf;
@@ -346,6 +356,14 @@
 		return;
 
 	/*
+	 * On some systems with overclocking enabled, CPPC.highest_perf is hardcoded to 0xff.
+	 * In this case we can't use CPPC.highest_perf to enable ITMT.
+	 * In this case we can look at MSR_HWP_CAPABILITIES bits [8:0] to decide.
+	 */
+	if (cppc_perf.highest_perf == CPPC_MAX_PERF)
+		cppc_perf.highest_perf = HWP_HIGHEST_PERF(READ_ONCE(all_cpu_data[cpu]->hwp_cap_cached));
+
+	/*
 	 * The priorities can be set regardless of whether or not
 	 * sched_set_itmt_support(true) has been called and it is valid to
 	 * update them at any time after it has been called.
@@ -386,15 +404,25 @@
 	return cppc_perf.nominal_perf;
 }
 
-static u32 intel_pstate_cppc_nominal(int cpu)
+static int intel_pstate_cppc_get_scaling(int cpu)
 {
-	u64 nominal_perf;
+	struct cppc_perf_caps cppc_perf;
+	int ret;
 
-	if (cppc_get_nominal_perf(cpu, &nominal_perf))
-		return 0;
+	ret = cppc_get_perf_caps(cpu, &cppc_perf);
 
-	return nominal_perf;
+	/*
+	 * If the nominal frequency and the nominal performance are not
+	 * zero and the ratio between them is not 100, return the hybrid
+	 * scaling factor.
+	 */
+	if (!ret && cppc_perf.nominal_perf && cppc_perf.nominal_freq &&
+	    cppc_perf.nominal_perf * 100 != cppc_perf.nominal_freq)
+		return HYBRID_SCALING_FACTOR;
+
+	return core_get_scaling();
 }
+
 #else /* CONFIG_ACPI_CPPC_LIB */
 static inline void intel_pstate_set_itmt_prio(int cpu)
 {
@@ -447,20 +475,6 @@
 			 (u32) cpu->acpi_perf_data.states[i].control);
 	}
 
-	/*
-	 * The _PSS table doesn't contain whole turbo frequency range.
-	 * This just contains +1 MHZ above the max non turbo frequency,
-	 * with control value corresponding to max turbo ratio. But
-	 * when cpufreq set policy is called, it will call with this
-	 * max frequency, which will cause a reduced performance as
-	 * this driver uses real max turbo frequency as the max
-	 * frequency. So correct this frequency in _PSS table to
-	 * correct max turbo frequency based on the turbo state.
-	 * Also need to convert to MHz as _PSS freq is in MHz.
-	 */
-	if (!global.turbo_disabled)
-		cpu->acpi_perf_data.states[0].core_frequency =
-					policy->cpuinfo.max_freq / 1000;
 	cpu->valid_pss_table = true;
 	pr_debug("_PPC limits will be enforced\n");
 
@@ -501,8 +515,37 @@
 {
 	return -ENOTSUPP;
 }
+
+static int intel_pstate_cppc_get_scaling(int cpu)
+{
+	return core_get_scaling();
+}
 #endif /* CONFIG_ACPI_CPPC_LIB */
 
+static int intel_pstate_freq_to_hwp_rel(struct cpudata *cpu, int freq,
+					unsigned int relation)
+{
+	if (freq == cpu->pstate.turbo_freq)
+		return cpu->pstate.turbo_pstate;
+
+	if (freq == cpu->pstate.max_freq)
+		return cpu->pstate.max_pstate;
+
+	switch (relation) {
+	case CPUFREQ_RELATION_H:
+		return freq / cpu->pstate.scaling;
+	case CPUFREQ_RELATION_C:
+		return DIV_ROUND_CLOSEST(freq, cpu->pstate.scaling);
+	}
+
+	return DIV_ROUND_UP(freq, cpu->pstate.scaling);
+}
+
+static int intel_pstate_freq_to_hwp(struct cpudata *cpu, int freq)
+{
+	return intel_pstate_freq_to_hwp_rel(cpu, freq, CPUFREQ_RELATION_L);
+}
+
 /**
  * intel_pstate_hybrid_hwp_adjust - Calibrate HWP performance levels.
  * @cpu: Target CPU.
@@ -518,47 +561,32 @@
 {
 	int perf_ctl_max_phys = cpu->pstate.max_pstate_physical;
 	int perf_ctl_scaling = cpu->pstate.perf_ctl_scaling;
-	int perf_ctl_turbo = pstate_funcs.get_turbo();
-	int turbo_freq = perf_ctl_turbo * perf_ctl_scaling;
+	int perf_ctl_turbo = pstate_funcs.get_turbo(cpu->cpu);
 	int scaling = cpu->pstate.scaling;
+	int freq;
 
 	pr_debug("CPU%d: perf_ctl_max_phys = %d\n", cpu->cpu, perf_ctl_max_phys);
-	pr_debug("CPU%d: perf_ctl_max = %d\n", cpu->cpu, pstate_funcs.get_max());
 	pr_debug("CPU%d: perf_ctl_turbo = %d\n", cpu->cpu, perf_ctl_turbo);
 	pr_debug("CPU%d: perf_ctl_scaling = %d\n", cpu->cpu, perf_ctl_scaling);
 	pr_debug("CPU%d: HWP_CAP guaranteed = %d\n", cpu->cpu, cpu->pstate.max_pstate);
 	pr_debug("CPU%d: HWP_CAP highest = %d\n", cpu->cpu, cpu->pstate.turbo_pstate);
 	pr_debug("CPU%d: HWP-to-frequency scaling factor: %d\n", cpu->cpu, scaling);
 
-	/*
-	 * If the product of the HWP performance scaling factor and the HWP_CAP
-	 * highest performance is greater than the maximum turbo frequency
-	 * corresponding to the pstate_funcs.get_turbo() return value, the
-	 * scaling factor is too high, so recompute it to make the HWP_CAP
-	 * highest performance correspond to the maximum turbo frequency.
-	 */
-	if (turbo_freq < cpu->pstate.turbo_pstate * scaling) {
-		cpu->pstate.turbo_freq = turbo_freq;
-		scaling = DIV_ROUND_UP(turbo_freq, cpu->pstate.turbo_pstate);
-		cpu->pstate.scaling = scaling;
-
-		pr_debug("CPU%d: refined HWP-to-frequency scaling factor: %d\n",
-			 cpu->cpu, scaling);
-	}
-
+	cpu->pstate.turbo_freq = rounddown(cpu->pstate.turbo_pstate * scaling,
+					   perf_ctl_scaling);
 	cpu->pstate.max_freq = rounddown(cpu->pstate.max_pstate * scaling,
 					 perf_ctl_scaling);
 
-	cpu->pstate.max_pstate_physical =
-			DIV_ROUND_UP(perf_ctl_max_phys * perf_ctl_scaling,
-				     scaling);
+	freq = perf_ctl_max_phys * perf_ctl_scaling;
+	cpu->pstate.max_pstate_physical = intel_pstate_freq_to_hwp(cpu, freq);
 
-	cpu->pstate.min_freq = cpu->pstate.min_pstate * perf_ctl_scaling;
+	freq = cpu->pstate.min_pstate * perf_ctl_scaling;
+	cpu->pstate.min_freq = freq;
 	/*
 	 * Cast the min P-state value retrieved via pstate_funcs.get_min() to
 	 * the effective range of HWP performance levels.
 	 */
-	cpu->pstate.min_pstate = DIV_ROUND_UP(cpu->pstate.min_freq, scaling);
+	cpu->pstate.min_pstate = intel_pstate_freq_to_hwp(cpu, freq);
 }
 
 static inline void update_turbo_state(void)
@@ -650,19 +678,29 @@
  *	3		balance_power
  *	4		power
  */
+
+enum energy_perf_value_index {
+	EPP_INDEX_DEFAULT = 0,
+	EPP_INDEX_PERFORMANCE,
+	EPP_INDEX_BALANCE_PERFORMANCE,
+	EPP_INDEX_BALANCE_POWERSAVE,
+	EPP_INDEX_POWERSAVE,
+};
+
 static const char * const energy_perf_strings[] = {
-	"default",
-	"performance",
-	"balance_performance",
-	"balance_power",
-	"power",
+	[EPP_INDEX_DEFAULT] = "default",
+	[EPP_INDEX_PERFORMANCE] = "performance",
+	[EPP_INDEX_BALANCE_PERFORMANCE] = "balance_performance",
+	[EPP_INDEX_BALANCE_POWERSAVE] = "balance_power",
+	[EPP_INDEX_POWERSAVE] = "power",
 	NULL
 };
-static const unsigned int epp_values[] = {
-	HWP_EPP_PERFORMANCE,
-	HWP_EPP_BALANCE_PERFORMANCE,
-	HWP_EPP_BALANCE_POWERSAVE,
-	HWP_EPP_POWERSAVE
+static unsigned int epp_values[] = {
+	[EPP_INDEX_DEFAULT] = 0, /* Unused index */
+	[EPP_INDEX_PERFORMANCE] = HWP_EPP_PERFORMANCE,
+	[EPP_INDEX_BALANCE_PERFORMANCE] = HWP_EPP_BALANCE_PERFORMANCE,
+	[EPP_INDEX_BALANCE_POWERSAVE] = HWP_EPP_BALANCE_POWERSAVE,
+	[EPP_INDEX_POWERSAVE] = HWP_EPP_POWERSAVE,
 };
 
 static int intel_pstate_get_energy_pref_index(struct cpudata *cpu_data, int *raw_epp)
@@ -676,14 +714,14 @@
 		return epp;
 
 	if (boot_cpu_has(X86_FEATURE_HWP_EPP)) {
-		if (epp == HWP_EPP_PERFORMANCE)
-			return 1;
-		if (epp == HWP_EPP_BALANCE_PERFORMANCE)
-			return 2;
-		if (epp == HWP_EPP_BALANCE_POWERSAVE)
-			return 3;
-		if (epp == HWP_EPP_POWERSAVE)
-			return 4;
+		if (epp == epp_values[EPP_INDEX_PERFORMANCE])
+			return EPP_INDEX_PERFORMANCE;
+		if (epp == epp_values[EPP_INDEX_BALANCE_PERFORMANCE])
+			return EPP_INDEX_BALANCE_PERFORMANCE;
+		if (epp == epp_values[EPP_INDEX_BALANCE_POWERSAVE])
+			return EPP_INDEX_BALANCE_POWERSAVE;
+		if (epp == epp_values[EPP_INDEX_POWERSAVE])
+			return EPP_INDEX_POWERSAVE;
 		*raw_epp = epp;
 		return 0;
 	} else if (boot_cpu_has(X86_FEATURE_EPB)) {
@@ -743,7 +781,7 @@
 		if (use_raw)
 			epp = raw_epp;
 		else if (epp == -EINVAL)
-			epp = epp_values[pref_index - 1];
+			epp = epp_values[pref_index];
 
 		/*
 		 * To avoid confusion, refuse to set EPP to any values different
@@ -829,7 +867,7 @@
 		 * upfront.
 		 */
 		if (!raw)
-			epp = ret ? epp_values[ret - 1] : cpu->epp_default;
+			epp = ret ? epp_values[ret] : cpu->epp_default;
 
 		if (cpu->epp_cached != epp) {
 			int err;
@@ -839,6 +877,8 @@
 			err = cpufreq_start_governor(policy);
 			if (!ret)
 				ret = err;
+		} else {
+			ret = 0;
 		}
 	}
 
@@ -998,9 +1038,22 @@
 		 */
 		value &= ~GENMASK_ULL(31, 24);
 		value |= HWP_ENERGY_PERF_PREFERENCE(cpu->epp_cached);
-		WRITE_ONCE(cpu->hwp_req_cached, value);
+		/*
+		 * However, make sure that EPP will be set to "performance" when
+		 * the CPU is brought back online again and the "performance"
+		 * scaling algorithm is still in effect.
+		 */
+		cpu->epp_policy = CPUFREQ_POLICY_UNKNOWN;
 	}
 
+	/*
+	 * Clear the desired perf field in the cached HWP request value to
+	 * prevent nonzero desired values from being leaked into the active
+	 * mode.
+	 */
+	value &= ~HWP_DESIRED_PERF(~0L);
+	WRITE_ONCE(cpu->hwp_req_cached, value);
+
 	value &= ~GENMASK_ULL(31, 0);
 	min_perf = HWP_LOWEST_PERF(READ_ONCE(cpu->hwp_cap_cached));
 
@@ -1553,11 +1606,19 @@
 		wrmsrl_on_cpu(cpudata->cpu, MSR_HWP_INTERRUPT, 0x00);
 
 	wrmsrl_on_cpu(cpudata->cpu, MSR_PM_ENABLE, 0x1);
-	if (cpudata->epp_default == -EINVAL)
+
+	if (cpudata->epp_default >= 0)
+		return;
+
+	if (epp_values[EPP_INDEX_BALANCE_PERFORMANCE] == HWP_EPP_BALANCE_PERFORMANCE) {
 		cpudata->epp_default = intel_pstate_get_epp(cpudata, 0);
+	} else {
+		cpudata->epp_default = epp_values[EPP_INDEX_BALANCE_PERFORMANCE];
+		intel_pstate_set_epp(cpudata, cpudata->epp_default);
+	}
 }
 
-static int atom_get_min_pstate(void)
+static int atom_get_min_pstate(int not_used)
 {
 	u64 value;
 
@@ -1565,7 +1626,7 @@
 	return (value >> 8) & 0x7F;
 }
 
-static int atom_get_max_pstate(void)
+static int atom_get_max_pstate(int not_used)
 {
 	u64 value;
 
@@ -1573,7 +1634,7 @@
 	return (value >> 16) & 0x7F;
 }
 
-static int atom_get_turbo_pstate(void)
+static int atom_get_turbo_pstate(int not_used)
 {
 	u64 value;
 
@@ -1651,23 +1712,23 @@
 	cpudata->vid.turbo = value & 0x7f;
 }
 
-static int core_get_min_pstate(void)
+static int core_get_min_pstate(int cpu)
 {
 	u64 value;
 
-	rdmsrl(MSR_PLATFORM_INFO, value);
+	rdmsrl_on_cpu(cpu, MSR_PLATFORM_INFO, &value);
 	return (value >> 40) & 0xFF;
 }
 
-static int core_get_max_pstate_physical(void)
+static int core_get_max_pstate_physical(int cpu)
 {
 	u64 value;
 
-	rdmsrl(MSR_PLATFORM_INFO, value);
+	rdmsrl_on_cpu(cpu, MSR_PLATFORM_INFO, &value);
 	return (value >> 8) & 0xFF;
 }
 
-static int core_get_tdp_ratio(u64 plat_info)
+static int core_get_tdp_ratio(int cpu, u64 plat_info)
 {
 	/* Check how many TDP levels present */
 	if (plat_info & 0x600000000) {
@@ -1677,13 +1738,13 @@
 		int err;
 
 		/* Get the TDP level (0, 1, 2) to get ratios */
-		err = rdmsrl_safe(MSR_CONFIG_TDP_CONTROL, &tdp_ctrl);
+		err = rdmsrl_safe_on_cpu(cpu, MSR_CONFIG_TDP_CONTROL, &tdp_ctrl);
 		if (err)
 			return err;
 
 		/* TDP MSR are continuous starting at 0x648 */
 		tdp_msr = MSR_CONFIG_TDP_NOMINAL + (tdp_ctrl & 0x03);
-		err = rdmsrl_safe(tdp_msr, &tdp_ratio);
+		err = rdmsrl_safe_on_cpu(cpu, tdp_msr, &tdp_ratio);
 		if (err)
 			return err;
 
@@ -1700,7 +1761,7 @@
 	return -ENXIO;
 }
 
-static int core_get_max_pstate(void)
+static int core_get_max_pstate(int cpu)
 {
 	u64 tar;
 	u64 plat_info;
@@ -1708,10 +1769,10 @@
 	int tdp_ratio;
 	int err;
 
-	rdmsrl(MSR_PLATFORM_INFO, plat_info);
+	rdmsrl_on_cpu(cpu, MSR_PLATFORM_INFO, &plat_info);
 	max_pstate = (plat_info >> 8) & 0xFF;
 
-	tdp_ratio = core_get_tdp_ratio(plat_info);
+	tdp_ratio = core_get_tdp_ratio(cpu, plat_info);
 	if (tdp_ratio <= 0)
 		return max_pstate;
 
@@ -1720,7 +1781,7 @@
 		return tdp_ratio;
 	}
 
-	err = rdmsrl_safe(MSR_TURBO_ACTIVATION_RATIO, &tar);
+	err = rdmsrl_safe_on_cpu(cpu, MSR_TURBO_ACTIVATION_RATIO, &tar);
 	if (!err) {
 		int tar_levels;
 
@@ -1735,24 +1796,19 @@
 	return max_pstate;
 }
 
-static int core_get_turbo_pstate(void)
+static int core_get_turbo_pstate(int cpu)
 {
 	u64 value;
 	int nont, ret;
 
-	rdmsrl(MSR_TURBO_RATIO_LIMIT, value);
-	nont = core_get_max_pstate();
+	rdmsrl_on_cpu(cpu, MSR_TURBO_RATIO_LIMIT, &value);
+	nont = core_get_max_pstate(cpu);
 	ret = (value) & 255;
 	if (ret <= nont)
 		ret = nont;
 	return ret;
 }
 
-static inline int core_get_scaling(void)
-{
-	return 100000;
-}
-
 static u64 core_get_val(struct cpudata *cpudata, int pstate)
 {
 	u64 val;
@@ -1769,50 +1825,49 @@
 	return 10;
 }
 
-static int knl_get_turbo_pstate(void)
+static int knl_get_turbo_pstate(int cpu)
 {
 	u64 value;
 	int nont, ret;
 
-	rdmsrl(MSR_TURBO_RATIO_LIMIT, value);
-	nont = core_get_max_pstate();
+	rdmsrl_on_cpu(cpu, MSR_TURBO_RATIO_LIMIT, &value);
+	nont = core_get_max_pstate(cpu);
 	ret = (((value) >> 8) & 0xFF);
 	if (ret <= nont)
 		ret = nont;
 	return ret;
 }
 
-#ifdef CONFIG_ACPI_CPPC_LIB
-static u32 hybrid_ref_perf;
-
-static int hybrid_get_cpu_scaling(int cpu)
+static void hybrid_get_type(void *data)
 {
-	return DIV_ROUND_UP(core_get_scaling() * hybrid_ref_perf,
-			    intel_pstate_cppc_nominal(cpu));
+	u8 *cpu_type = data;
+
+	*cpu_type = get_this_hybrid_cpu_type();
 }
 
-static void intel_pstate_cppc_set_cpu_scaling(void)
+static int hwp_get_cpu_scaling(int cpu)
 {
-	u32 min_nominal_perf = U32_MAX;
-	int cpu;
+	u8 cpu_type = 0;
 
-	for_each_present_cpu(cpu) {
-		u32 nominal_perf = intel_pstate_cppc_nominal(cpu);
+	smp_call_function_single(cpu, hybrid_get_type, &cpu_type, 1);
+	/* P-cores have a smaller perf level-to-freqency scaling factor. */
+	if (cpu_type == 0x40)
+		return HYBRID_SCALING_FACTOR;
 
-		if (nominal_perf && nominal_perf < min_nominal_perf)
-			min_nominal_perf = nominal_perf;
-	}
+	/* Use default core scaling for E-cores */
+	if (cpu_type == 0x20)
+		return core_get_scaling();
 
-	if (min_nominal_perf < U32_MAX) {
-		hybrid_ref_perf = min_nominal_perf;
-		pstate_funcs.get_cpu_scaling = hybrid_get_cpu_scaling;
-	}
-}
-#else
-static inline void intel_pstate_cppc_set_cpu_scaling(void)
-{
+	/*
+	 * If reached here, this system is either non-hybrid (like Tiger
+	 * Lake) or hybrid-capable (like Alder Lake or Raptor Lake) with
+	 * no E cores (in which case CPUID for hybrid support is 0).
+	 *
+	 * The CPPC nominal_frequency field is 0 for non-hybrid systems,
+	 * so the default core scaling will be used for them.
+	 */
+	return intel_pstate_cppc_get_scaling(cpu);
 }
-#endif /* CONFIG_ACPI_CPPC_LIB */
 
 static void intel_pstate_set_pstate(struct cpudata *cpu, int pstate)
 {
@@ -1842,10 +1897,10 @@
 
 static void intel_pstate_get_cpu_pstates(struct cpudata *cpu)
 {
-	int perf_ctl_max_phys = pstate_funcs.get_max_physical();
+	int perf_ctl_max_phys = pstate_funcs.get_max_physical(cpu->cpu);
 	int perf_ctl_scaling = pstate_funcs.get_scaling();
 
-	cpu->pstate.min_pstate = pstate_funcs.get_min();
+	cpu->pstate.min_pstate = pstate_funcs.get_min(cpu->cpu);
 	cpu->pstate.max_pstate_physical = perf_ctl_max_phys;
 	cpu->pstate.perf_ctl_scaling = perf_ctl_scaling;
 
@@ -1861,8 +1916,8 @@
 		}
 	} else {
 		cpu->pstate.scaling = perf_ctl_scaling;
-		cpu->pstate.max_pstate = pstate_funcs.get_max();
-		cpu->pstate.turbo_pstate = pstate_funcs.get_turbo();
+		cpu->pstate.max_pstate = pstate_funcs.get_max(cpu->cpu);
+		cpu->pstate.turbo_pstate = pstate_funcs.get_turbo(cpu->cpu);
 	}
 
 	if (cpu->pstate.scaling == perf_ctl_scaling) {
@@ -2233,6 +2288,7 @@
 	X86_MATCH(SKYLAKE_X,		core_funcs),
 	X86_MATCH(COMETLAKE,		core_funcs),
 	X86_MATCH(ICELAKE_X,		core_funcs),
+	X86_MATCH(TIGERLAKE,		core_funcs),
 	{}
 };
 MODULE_DEVICE_TABLE(x86cpu, intel_pstate_cpu_ids);
@@ -2241,6 +2297,7 @@
 	X86_MATCH(BROADWELL_D,		core_funcs),
 	X86_MATCH(BROADWELL_X,		core_funcs),
 	X86_MATCH(SKYLAKE_X,		core_funcs),
+	X86_MATCH(ICELAKE_X,		core_funcs),
 	{}
 };
 
@@ -2249,12 +2306,6 @@
 	{}
 };
 
-static const struct x86_cpu_id intel_pstate_hwp_boost_ids[] = {
-	X86_MATCH(SKYLAKE_X,		core_funcs),
-	X86_MATCH(SKYLAKE,		core_funcs),
-	{}
-};
-
 static int intel_pstate_init_cpu(unsigned int cpunum)
 {
 	struct cpudata *cpu;
@@ -2273,12 +2324,9 @@
 		cpu->epp_default = -EINVAL;
 
 		if (hwp_active) {
-			const struct x86_cpu_id *id;
-
 			intel_pstate_hwp_enable(cpu);
 
-			id = x86_match_cpu(intel_pstate_hwp_boost_ids);
-			if (id && intel_pstate_acpi_pm_profile_server())
+			if (intel_pstate_acpi_pm_profile_server())
 				hwp_boost = true;
 		}
 	} else if (hwp_active) {
@@ -2357,18 +2405,13 @@
 	 * HWP needs some special consideration, because HWP_REQUEST uses
 	 * abstract values to represent performance rather than pure ratios.
 	 */
-	if (hwp_active) {
-		intel_pstate_get_hwp_cap(cpu);
+	if (hwp_active && cpu->pstate.scaling != perf_ctl_scaling) {
+		int freq;
 
-		if (cpu->pstate.scaling != perf_ctl_scaling) {
-			int scaling = cpu->pstate.scaling;
-			int freq;
-
-			freq = max_policy_perf * perf_ctl_scaling;
-			max_policy_perf = DIV_ROUND_UP(freq, scaling);
-			freq = min_policy_perf * perf_ctl_scaling;
-			min_policy_perf = DIV_ROUND_UP(freq, scaling);
-		}
+		freq = max_policy_perf * perf_ctl_scaling;
+		max_policy_perf = intel_pstate_freq_to_hwp(cpu, freq);
+		freq = min_policy_perf * perf_ctl_scaling;
+		min_policy_perf = intel_pstate_freq_to_hwp(cpu, freq);
 	}
 
 	pr_debug("cpu:%d min_policy_perf:%d max_policy_perf:%d\n",
@@ -2737,18 +2780,7 @@
 
 	cpufreq_freq_transition_begin(policy, &freqs);
 
-	switch (relation) {
-	case CPUFREQ_RELATION_L:
-		target_pstate = DIV_ROUND_UP(freqs.new, cpu->pstate.scaling);
-		break;
-	case CPUFREQ_RELATION_H:
-		target_pstate = freqs.new / cpu->pstate.scaling;
-		break;
-	default:
-		target_pstate = DIV_ROUND_CLOSEST(freqs.new, cpu->pstate.scaling);
-		break;
-	}
-
+	target_pstate = intel_pstate_freq_to_hwp_rel(cpu, freqs.new, relation);
 	target_pstate = intel_cpufreq_update_pstate(policy, target_pstate, false);
 
 	freqs.new = target_pstate * cpu->pstate.scaling;
@@ -2766,7 +2798,7 @@
 
 	update_turbo_state();
 
-	target_pstate = DIV_ROUND_UP(target_freq, cpu->pstate.scaling);
+	target_pstate = intel_pstate_freq_to_hwp(cpu, target_freq);
 
 	target_pstate = intel_cpufreq_update_pstate(policy, target_pstate, true);
 
@@ -2803,6 +2835,9 @@
 	if (min_pstate < cpu->min_perf_ratio)
 		min_pstate = cpu->min_perf_ratio;
 
+	if (min_pstate > cpu->max_perf_ratio)
+		min_pstate = cpu->max_perf_ratio;
+
 	max_pstate = min(cap_pstate, cpu->max_perf_ratio);
 	if (max_pstate < min_pstate)
 		max_pstate = min_pstate;
@@ -2902,6 +2937,27 @@
 	return intel_pstate_cpu_exit(policy);
 }
 
+static int intel_cpufreq_suspend(struct cpufreq_policy *policy)
+{
+	intel_pstate_suspend(policy);
+
+	if (hwp_active) {
+		struct cpudata *cpu = all_cpu_data[policy->cpu];
+		u64 value = READ_ONCE(cpu->hwp_req_cached);
+
+		/*
+		 * Clear the desired perf field in MSR_HWP_REQUEST in case
+		 * intel_cpufreq_adjust_perf() is in use and the last value
+		 * written by it may not be suitable.
+		 */
+		value &= ~HWP_DESIRED_PERF(~0L);
+		wrmsrl_on_cpu(cpu->cpu, MSR_HWP_REQUEST, value);
+		WRITE_ONCE(cpu->hwp_req_cached, value);
+	}
+
+	return 0;
+}
+
 static struct cpufreq_driver intel_cpufreq = {
 	.flags		= CPUFREQ_CONST_LOOPS,
 	.verify		= intel_cpufreq_verify_policy,
@@ -2911,7 +2967,7 @@
 	.exit		= intel_cpufreq_cpu_exit,
 	.offline	= intel_cpufreq_cpu_offline,
 	.online		= intel_pstate_cpu_online,
-	.suspend	= intel_pstate_suspend,
+	.suspend	= intel_cpufreq_suspend,
 	.resume		= intel_pstate_resume,
 	.update_limits	= intel_pstate_update_limits,
 	.name		= "intel_cpufreq",
@@ -3016,9 +3072,9 @@
 
 static int __init intel_pstate_msrs_not_valid(void)
 {
-	if (!pstate_funcs.get_max() ||
-	    !pstate_funcs.get_min() ||
-	    !pstate_funcs.get_turbo())
+	if (!pstate_funcs.get_max(0) ||
+	    !pstate_funcs.get_min(0) ||
+	    !pstate_funcs.get_turbo(0))
 		return -ENODEV;
 
 	return 0;
@@ -3197,6 +3253,17 @@
 	return !!(value & 0x1);
 }
 
+static const struct x86_cpu_id intel_epp_balance_perf[] = {
+	/*
+	 * Set EPP value as 102, this is the max suggested EPP
+	 * which can result in one core turbo frequency for
+	 * AlderLake Mobile CPUs.
+	 */
+	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L, 102),
+	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X, 32),
+	{}
+};
+
 static int __init intel_pstate_init(void)
 {
 	const struct x86_cpu_id *id;
@@ -3233,8 +3300,7 @@
 			if (!default_driver)
 				default_driver = &intel_pstate;
 
-			if (boot_cpu_has(X86_FEATURE_HYBRID_CPU))
-				intel_pstate_cppc_set_cpu_scaling();
+			pstate_funcs.get_cpu_scaling = hwp_get_cpu_scaling;
 
 			goto hwp_cpu_matched;
 		}
@@ -3283,6 +3349,13 @@
 
 	intel_pstate_sysfs_expose_params();
 
+	if (hwp_active) {
+		const struct x86_cpu_id *id = x86_match_cpu(intel_epp_balance_perf);
+
+		if (id)
+			epp_values[EPP_INDEX_BALANCE_PERFORMANCE] = id->driver_data;
+	}
+
 	mutex_lock(&intel_pstate_driver_lock);
 	rc = intel_pstate_register_driver(default_driver);
 	mutex_unlock(&intel_pstate_driver_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/loongson2_cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/loongson2_cpufreq.c
@@ -154,7 +154,9 @@
 
 	ret = cpufreq_register_driver(&loongson2_cpufreq_driver);
 
-	if (!ret && !nowait) {
+	if (ret) {
+		platform_driver_unregister(&platform_driver);
+	} else if (!nowait) {
 		saved_cpu_wait = cpu_wait;
 		cpu_wait = loongson2_cpu_wait;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/mediatek-cpufreq-hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/mediatek-cpufreq-hw.c
@@ -10,8 +10,10 @@
 #include <linux/iopoll.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/of_address.h>
+#include <linux/of.h>
 #include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 
 #define LUT_MAX_ENTRIES			32U
@@ -58,7 +60,7 @@
 
 	policy = cpufreq_cpu_get_raw(cpu_dev->id);
 	if (!policy)
-		return 0;
+		return -EINVAL;
 
 	data = policy->driver_data;
 
@@ -267,7 +269,23 @@
 static int mtk_cpufreq_hw_driver_probe(struct platform_device *pdev)
 {
 	const void *data;
-	int ret;
+	int ret, cpu;
+	struct device *cpu_dev;
+	struct regulator *cpu_reg;
+
+	/* Make sure that all CPU supplies are available before proceeding. */
+	for_each_possible_cpu(cpu) {
+		cpu_dev = get_cpu_device(cpu);
+		if (!cpu_dev)
+			return dev_err_probe(&pdev->dev, -EPROBE_DEFER,
+					     "Failed to get cpu%d device\n", cpu);
+
+		cpu_reg = devm_regulator_get(cpu_dev, "cpu");
+		if (IS_ERR(cpu_reg))
+			return dev_err_probe(&pdev->dev, PTR_ERR(cpu_reg),
+					     "CPU%d regulator get failed\n", cpu);
+	}
+
 
 	data = of_device_get_match_data(&pdev->dev);
 	if (!data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/mediatek-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/mediatek-cpufreq.c
@@ -44,6 +44,8 @@
 	bool need_voltage_tracking;
 };
 
+static struct platform_device *cpufreq_pdev;
+
 static LIST_HEAD(dvfs_info_list);
 
 static struct mtk_cpu_dvfs_info *mtk_cpu_dvfs_info_lookup(int cpu)
@@ -547,7 +549,6 @@
 {
 	struct device_node *np;
 	const struct of_device_id *match;
-	struct platform_device *pdev;
 	int err;
 
 	np = of_find_node_by_path("/");
@@ -571,16 +572,23 @@
 	 * and the device registration codes are put here to handle defer
 	 * probing.
 	 */
-	pdev = platform_device_register_simple("mtk-cpufreq", -1, NULL, 0);
-	if (IS_ERR(pdev)) {
+	cpufreq_pdev = platform_device_register_simple("mtk-cpufreq", -1, NULL, 0);
+	if (IS_ERR(cpufreq_pdev)) {
 		pr_err("failed to register mtk-cpufreq platform device\n");
 		platform_driver_unregister(&mtk_cpufreq_platdrv);
-		return PTR_ERR(pdev);
+		return PTR_ERR(cpufreq_pdev);
 	}
 
 	return 0;
 }
-device_initcall(mtk_cpufreq_driver_init);
+module_init(mtk_cpufreq_driver_init)
+
+static void __exit mtk_cpufreq_driver_exit(void)
+{
+	platform_device_unregister(cpufreq_pdev);
+	platform_driver_unregister(&mtk_cpufreq_platdrv);
+}
+module_exit(mtk_cpufreq_driver_exit)
 
 MODULE_DESCRIPTION("MediaTek CPUFreq driver");
 MODULE_AUTHOR("Pi-Cheng Chen <pi-cheng.chen@linaro.org>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/pmac32-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/pmac32-cpufreq.c
@@ -470,6 +470,10 @@
 	if (slew_done_gpio_np)
 		slew_done_gpio = read_gpio(slew_done_gpio_np);
 
+	of_node_put(volt_gpio_np);
+	of_node_put(freq_gpio_np);
+	of_node_put(slew_done_gpio_np);
+
 	/* If we use the frequency GPIOs, calculate the min/max speeds based
 	 * on the bus frequencies
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/powernow-k8.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/powernow-k8.c
@@ -1101,7 +1101,8 @@
 
 	kfree(data->powernow_table);
 	kfree(data);
-	for_each_cpu(cpu, pol->cpus)
+	/* pol->cpus will be empty here, use related_cpus instead. */
+	for_each_cpu(cpu, pol->related_cpus)
 		per_cpu(powernow_data, cpu) = NULL;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/ppc_cbe_cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/ppc_cbe_cpufreq.c
@@ -9,7 +9,7 @@
 
 #include <linux/cpufreq.h>
 #include <linux/module.h>
-#include <linux/of_platform.h>
+#include <linux/of.h>
 
 #include <asm/machdep.h>
 #include <asm/prom.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/ppc_cbe_cpufreq_pmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/ppc_cbe_cpufreq_pmi.c
@@ -11,7 +11,6 @@
 #include <linux/types.h>
 #include <linux/timer.h>
 #include <linux/init.h>
-#include <linux/of_platform.h>
 #include <linux/pm_qos.h>
 
 #include <asm/processor.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/qcom-cpufreq-hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/qcom-cpufreq-hw.c
@@ -24,12 +24,16 @@
 #define CLK_HW_DIV			2
 #define LUT_TURBO_IND			1
 
+#define GT_IRQ_STATUS			BIT(2)
+
 #define HZ_PER_KHZ			1000
 
 struct qcom_cpufreq_soc_data {
 	u32 reg_enable;
+	u32 reg_domain_state;
 	u32 reg_freq_lut;
 	u32 reg_volt_lut;
+	u32 reg_intr_clr;
 	u32 reg_current_vote;
 	u32 reg_perf_state;
 	u8 lut_row_size;
@@ -173,6 +177,7 @@
 		}
 	} else if (ret != -ENODEV) {
 		dev_err(cpu_dev, "Invalid opp table in device tree\n");
+		kfree(table);
 		return ret;
 	} else {
 		policy->fast_switch_possible = true;
@@ -266,28 +271,31 @@
 	}
 }
 
-static unsigned int qcom_lmh_get_throttle_freq(struct qcom_cpufreq_data *data)
+static unsigned long qcom_lmh_get_throttle_freq(struct qcom_cpufreq_data *data)
 {
-	unsigned int val = readl_relaxed(data->base + data->soc_data->reg_current_vote);
+	unsigned int lval;
+
+	if (data->soc_data->reg_current_vote)
+		lval = readl_relaxed(data->base + data->soc_data->reg_current_vote) & 0x3ff;
+	else
+		lval = readl_relaxed(data->base + data->soc_data->reg_domain_state) & 0xff;
 
-	return (val & 0x3FF) * 19200;
+	return lval * xo_rate;
 }
 
 static void qcom_lmh_dcvs_notify(struct qcom_cpufreq_data *data)
 {
 	unsigned long max_capacity, capacity, freq_hz, throttled_freq;
 	struct cpufreq_policy *policy = data->policy;
-	int cpu = cpumask_first(policy->cpus);
+	int cpu = cpumask_first(policy->related_cpus);
 	struct device *dev = get_cpu_device(cpu);
 	struct dev_pm_opp *opp;
-	unsigned int freq;
 
 	/*
 	 * Get the h/w throttled frequency, normalize it using the
 	 * registered opp table and use it to calculate thermal pressure.
 	 */
-	freq = qcom_lmh_get_throttle_freq(data);
-	freq_hz = freq * HZ_PER_KHZ;
+	freq_hz = qcom_lmh_get_throttle_freq(data);
 
 	opp = dev_pm_opp_find_freq_floor(dev, &freq_hz);
 	if (IS_ERR(opp) && PTR_ERR(opp) == -ERANGE)
@@ -304,7 +312,8 @@
 	if (capacity > max_capacity)
 		capacity = max_capacity;
 
-	arch_set_thermal_pressure(policy->cpus, max_capacity - capacity);
+	arch_set_thermal_pressure(policy->related_cpus,
+				  max_capacity - capacity);
 
 	/*
 	 * In the unlikely case policy is unregistered do not enable
@@ -342,9 +351,13 @@
 
 	/* Disable interrupt and enable polling */
 	disable_irq_nosync(c_data->throttle_irq);
-	qcom_lmh_dcvs_notify(c_data);
+	schedule_delayed_work(&c_data->throttle_work, 0);
 
-	return 0;
+	if (c_data->soc_data->reg_intr_clr)
+		writel_relaxed(GT_IRQ_STATUS,
+			       c_data->base + c_data->soc_data->reg_intr_clr);
+
+	return IRQ_HANDLED;
 }
 
 static const struct qcom_cpufreq_soc_data qcom_soc_data = {
@@ -358,8 +371,10 @@
 
 static const struct qcom_cpufreq_soc_data epss_soc_data = {
 	.reg_enable = 0x0,
+	.reg_domain_state = 0x20,
 	.reg_freq_lut = 0x100,
 	.reg_volt_lut = 0x200,
+	.reg_intr_clr = 0x308,
 	.reg_perf_state = 0x320,
 	.lut_row_size = 4,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/qcom-cpufreq-nvmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/qcom-cpufreq-nvmem.c
@@ -22,7 +22,6 @@
 #include <linux/module.h>
 #include <linux/nvmem-consumer.h>
 #include <linux/of.h>
-#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
 #include <linux/pm_opp.h>
@@ -130,7 +129,7 @@
 	}
 
 	/* Check PVS_BLOW_STATUS */
-	pte_efuse = *(((u32 *)buf) + 4);
+	pte_efuse = *(((u32 *)buf) + 1);
 	pte_efuse &= BIT(21);
 	if (pte_efuse) {
 		dev_dbg(cpu_dev, "PVS bin: %d\n", *pvs);
@@ -215,6 +214,7 @@
 	int speed = 0, pvs = 0, pvs_ver = 0;
 	u8 *speedbin;
 	size_t len;
+	int ret = 0;
 
 	speedbin = nvmem_cell_read(speedbin_nvmem, &len);
 
@@ -232,7 +232,8 @@
 		break;
 	default:
 		dev_err(cpu_dev, "Unable to read nvmem data. Defaulting to 0!\n");
-		return -ENODEV;
+		ret = -ENODEV;
+		goto len_error;
 	}
 
 	snprintf(*pvs_name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d",
@@ -240,8 +241,9 @@
 
 	drv->versions = (1 << speed);
 
+len_error:
 	kfree(speedbin);
-	return 0;
+	return ret;
 }
 
 static const struct qcom_cpufreq_match_data match_data_kryo = {
@@ -264,7 +266,8 @@
 	struct nvmem_cell *speedbin_nvmem;
 	struct device_node *np;
 	struct device *cpu_dev;
-	char *pvs_name = "speedXX-pvsXX-vXX";
+	char pvs_name_buffer[] = "speedXX-pvsXX-vXX";
+	char *pvs_name = pvs_name_buffer;
 	unsigned cpu;
 	const struct of_device_id *match;
 	int ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/qoriq-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/qoriq-cpufreq.c
@@ -275,6 +275,7 @@
 
 	np = of_find_matching_node(NULL, qoriq_cpufreq_blacklist);
 	if (np) {
+		of_node_put(np);
 		dev_info(&pdev->dev, "Disabling due to erratum A-008083");
 		return -ENODEV;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/s3c64xx-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/s3c64xx-cpufreq.c
@@ -24,6 +24,7 @@
 	unsigned int vddarm_max;
 };
 
+#ifdef CONFIG_REGULATOR
 static struct s3c64xx_dvfs s3c64xx_dvfs_table[] = {
 	[0] = { 1000000, 1150000 },
 	[1] = { 1050000, 1150000 },
@@ -31,6 +32,7 @@
 	[3] = { 1200000, 1350000 },
 	[4] = { 1300000, 1350000 },
 };
+#endif
 
 static struct cpufreq_frequency_table s3c64xx_freq_table[] = {
 	{ 0, 0,  66000 },
@@ -51,15 +53,16 @@
 static int s3c64xx_cpufreq_set_target(struct cpufreq_policy *policy,
 				      unsigned int index)
 {
-	struct s3c64xx_dvfs *dvfs;
-	unsigned int old_freq, new_freq;
+	unsigned int new_freq = s3c64xx_freq_table[index].frequency;
 	int ret;
 
+#ifdef CONFIG_REGULATOR
+	struct s3c64xx_dvfs *dvfs;
+	unsigned int old_freq;
+
 	old_freq = clk_get_rate(policy->clk) / 1000;
-	new_freq = s3c64xx_freq_table[index].frequency;
 	dvfs = &s3c64xx_dvfs_table[s3c64xx_freq_table[index].driver_data];
 
-#ifdef CONFIG_REGULATOR
 	if (vddarm && new_freq > old_freq) {
 		ret = regulator_set_voltage(vddarm,
 					    dvfs->vddarm_min,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/scmi-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/scmi-cpufreq.c
@@ -61,9 +61,9 @@
 					     unsigned int target_freq)
 {
 	struct scmi_data *priv = policy->driver_data;
+	unsigned long freq = target_freq;
 
-	if (!perf_ops->freq_set(ph, priv->domain_id,
-				target_freq * 1000, true))
+	if (!perf_ops->freq_set(ph, priv->domain_id, freq * 1000, true))
 		return target_freq;
 
 	return 0;
@@ -299,8 +299,11 @@
 
 #ifdef CONFIG_COMMON_CLK
 	/* dummy clock provider as needed by OPP if clocks property is used */
-	if (of_find_property(dev->of_node, "#clock-cells", NULL))
-		devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, NULL);
+	if (of_property_present(dev->of_node, "#clock-cells")) {
+		ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, NULL);
+		if (ret)
+			return dev_err_probe(dev, ret, "%s: registering clock provider failed\n", __func__);
+	}
 #endif
 
 	ret = cpufreq_register_driver(&scmi_cpufreq_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/scpi-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/scpi-cpufreq.c
@@ -22,7 +22,7 @@
 #include <linux/cpumask.h>
 #include <linux/export.h>
 #include <linux/module.h>
-#include <linux/of_platform.h>
+#include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/scpi_protocol.h>
 #include <linux/slab.h>
@@ -47,8 +47,9 @@
 static int
 scpi_cpufreq_set_target(struct cpufreq_policy *policy, unsigned int index)
 {
-	u64 rate = policy->freq_table[index].frequency * 1000;
+	unsigned long freq_khz = policy->freq_table[index].frequency;
 	struct scpi_data *priv = policy->driver_data;
+	unsigned long rate = freq_khz * 1000;
 	int ret;
 
 	ret = clk_set_rate(priv->clk, rate);
@@ -56,7 +57,7 @@
 	if (ret)
 		return ret;
 
-	if (clk_get_rate(priv->clk) != rate)
+	if (clk_get_rate(priv->clk) / 1000 != freq_khz)
 		return -EIO;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/sti-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/sti-cpufreq.c
@@ -13,7 +13,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
-#include <linux/of_platform.h>
+#include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/regmap.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/sun50i-cpufreq-nvmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/sun50i-cpufreq-nvmem.c
@@ -98,8 +98,10 @@
 		return -ENOMEM;
 
 	ret = sun50i_cpufreq_get_efuse(&speed);
-	if (ret)
+	if (ret) {
+		kfree(opp_tables);
 		return ret;
+	}
 
 	snprintf(name, MAX_NAME_LEN, "speed%d", speed);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/tegra20-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/tegra20-cpufreq.c
@@ -25,7 +25,7 @@
 	struct device_node *np = of_cpu_device_node_get(0);
 	bool ret = false;
 
-	if (of_get_property(np, "operating-points-v2", NULL))
+	if (of_property_present(np, "operating-points-v2"))
 		ret = true;
 
 	of_node_put(np);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/ti-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/ti-cpufreq.c
@@ -12,7 +12,7 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/of.h>
-#include <linux/of_platform.h>
+#include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
@@ -53,6 +53,9 @@
 	unsigned long efuse_shift;
 	unsigned long rev_offset;
 	bool multi_regulator;
+/* Backward compatibility hack: Might have missing syscon */
+#define TI_QUIRK_SYSCON_MAY_BE_MISSING	0x1
+	u8 quirks;
 };
 
 struct ti_cpufreq_data {
@@ -156,6 +159,7 @@
 	.efuse_mask = BIT(3),
 	.rev_offset = OMAP3_CONTROL_IDCODE - OMAP3_SYSCON_BASE,
 	.multi_regulator = false,
+	.quirks = TI_QUIRK_SYSCON_MAY_BE_MISSING,
 };
 
 /*
@@ -183,6 +187,7 @@
 	.efuse_mask = BIT(9),
 	.rev_offset = OMAP3_CONTROL_IDCODE - OMAP3_SYSCON_BASE,
 	.multi_regulator = true,
+	.quirks = TI_QUIRK_SYSCON_MAY_BE_MISSING,
 };
 
 /*
@@ -197,6 +202,7 @@
 	.efuse_mask = 0,
 	.rev_offset = OMAP3_CONTROL_IDCODE - OMAP3_SYSCON_BASE,
 	.multi_regulator = false,
+	.quirks = TI_QUIRK_SYSCON_MAY_BE_MISSING,
 };
 
 
@@ -216,7 +222,7 @@
 
 	ret = regmap_read(opp_data->syscon, opp_data->soc_data->efuse_offset,
 			  &efuse);
-	if (ret == -EIO) {
+	if (opp_data->soc_data->quirks & TI_QUIRK_SYSCON_MAY_BE_MISSING && ret == -EIO) {
 		/* not a syscon register! */
 		void __iomem *regs = ioremap(OMAP3_SYSCON_BASE +
 				opp_data->soc_data->efuse_offset, 4);
@@ -257,7 +263,7 @@
 
 	ret = regmap_read(opp_data->syscon, opp_data->soc_data->rev_offset,
 			  &revision);
-	if (ret == -EIO) {
+	if (opp_data->soc_data->quirks & TI_QUIRK_SYSCON_MAY_BE_MISSING && ret == -EIO) {
 		/* not a syscon register! */
 		void __iomem *regs = ioremap(OMAP3_SYSCON_BASE +
 				opp_data->soc_data->rev_offset, 4);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpufreq/vexpress-spc-cpufreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpufreq/vexpress-spc-cpufreq.c
@@ -18,7 +18,6 @@
 #include <linux/device.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
-#include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/slab.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpuidle/cpuidle-psci-domain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpuidle/cpuidle-psci-domain.c
@@ -182,7 +182,8 @@
 	struct psci_pd_provider *pd_provider, *it;
 	struct generic_pm_domain *genpd;
 
-	list_for_each_entry_safe(pd_provider, it, &psci_pd_providers, link) {
+	list_for_each_entry_safe_reverse(pd_provider, it,
+					 &psci_pd_providers, link) {
 		of_genpd_del_provider(pd_provider->node);
 
 		genpd = of_genpd_remove_last(pd_provider->node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpuidle/cpuidle-psci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpuidle/cpuidle-psci.c
@@ -23,6 +23,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/slab.h>
 #include <linux/string.h>
+#include <linux/syscore_ops.h>
 
 #include <asm/cpuidle.h>
 
@@ -131,6 +132,49 @@
 	return 0;
 }
 
+static void psci_idle_syscore_switch(bool suspend)
+{
+	bool cleared = false;
+	struct device *dev;
+	int cpu;
+
+	for_each_possible_cpu(cpu) {
+		dev = per_cpu_ptr(&psci_cpuidle_data, cpu)->dev;
+
+		if (dev && suspend) {
+			dev_pm_genpd_suspend(dev);
+		} else if (dev) {
+			dev_pm_genpd_resume(dev);
+
+			/* Account for userspace having offlined a CPU. */
+			if (pm_runtime_status_suspended(dev))
+				pm_runtime_set_active(dev);
+
+			/* Clear domain state to re-start fresh. */
+			if (!cleared) {
+				psci_set_domain_state(0);
+				cleared = true;
+			}
+		}
+	}
+}
+
+static int psci_idle_syscore_suspend(void)
+{
+	psci_idle_syscore_switch(true);
+	return 0;
+}
+
+static void psci_idle_syscore_resume(void)
+{
+	psci_idle_syscore_switch(false);
+}
+
+static struct syscore_ops psci_idle_syscore_ops = {
+	.suspend = psci_idle_syscore_suspend,
+	.resume = psci_idle_syscore_resume,
+};
+
 static void psci_idle_init_cpuhp(void)
 {
 	int err;
@@ -138,6 +182,8 @@
 	if (!psci_cpuidle_use_cpuhp)
 		return;
 
+	register_syscore_ops(&psci_idle_syscore_ops);
+
 	err = cpuhp_setup_state_nocalls(CPUHP_AP_CPU_PM_STARTING,
 					"cpuidle/psci:online",
 					psci_idle_cpuhp_up,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpuidle/cpuidle-pseries.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpuidle/cpuidle-pseries.c
@@ -410,13 +410,7 @@
 		return -ENODEV;
 
 	if (firmware_has_feature(FW_FEATURE_SPLPAR)) {
-		/*
-		 * Use local_paca instead of get_lppaca() since
-		 * preemption is not disabled, and it is not required in
-		 * fact, since lppaca_ptr does not need to be the value
-		 * associated to the current CPU, it can be from any CPU.
-		 */
-		if (lppaca_shared_proc(local_paca->lppaca_ptr)) {
+		if (lppaca_shared_proc()) {
 			cpuidle_state_table = shared_states;
 			max_idle_state = ARRAY_SIZE(shared_states);
 		} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpuidle/driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpuidle/driver.c
@@ -16,6 +16,7 @@
 #include <linux/cpumask.h>
 #include <linux/tick.h>
 #include <linux/cpu.h>
+#include <linux/math64.h>
 
 #include "cpuidle.h"
 
@@ -185,7 +186,7 @@
 			s->target_residency_ns = 0;
 
 		if (s->exit_latency > 0)
-			s->exit_latency_ns = s->exit_latency * NSEC_PER_USEC;
+			s->exit_latency_ns = mul_u32_u32(s->exit_latency, NSEC_PER_USEC);
 		else if (s->exit_latency_ns < 0)
 			s->exit_latency_ns =  0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpuidle/dt_idle_states.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpuidle/dt_idle_states.c
@@ -223,6 +223,6 @@
 	 * also be 0 on platforms with missing DT idle states or legacy DT
 	 * configuration predating the DT idle states bindings.
 	 */
-	return i;
+	return state_idx - start_idx;
 }
 EXPORT_SYMBOL_GPL(dt_init_idle_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cpuidle/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cpuidle/sysfs.c
@@ -488,6 +488,7 @@
 					   &kdev->kobj, "state%d", i);
 		if (ret) {
 			kobject_put(&kobj->kobj);
+			kfree(kobj);
 			goto error_state;
 		}
 		cpuidle_add_s2idle_attr_group(kobj);
@@ -619,6 +620,7 @@
 				   &kdev->kobj, "driver");
 	if (ret) {
 		kobject_put(&kdrv->kobj);
+		kfree(kdrv);
 		return ret;
 	}
 
@@ -705,7 +707,6 @@
 	if (!kdev)
 		return -ENOMEM;
 	kdev->dev = dev;
-	dev->kobj_dev = kdev;
 
 	init_completion(&kdev->kobj_unregister);
 
@@ -713,9 +714,11 @@
 				   "cpuidle");
 	if (error) {
 		kobject_put(&kdev->kobj);
+		kfree(kdev);
 		return error;
 	}
 
+	dev->kobj_dev = kdev;
 	kobject_uevent(&kdev->kobj, KOBJ_ADD);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/Kconfig
@@ -213,6 +213,18 @@
 	  key sizes and XTS mode is hardware accelerated for 256 and
 	  512 bit keys.
 
+config CRYPTO_CHACHA_S390
+	tristate "ChaCha20 stream cipher"
+	depends on S390
+	select CRYPTO_ALGAPI
+	select CRYPTO_SKCIPHER
+	select CRYPTO_CHACHA20
+	help
+	  This is the s390 SIMD implementation of the ChaCha20 stream
+	  cipher (RFC 7539).
+
+	  It is available as of z13.
+
 config S390_PRNG
 	tristate "Pseudo random number generator device driver"
 	depends on S390
@@ -772,7 +784,12 @@
 config CRYPTO_DEV_ROCKCHIP
 	tristate "Rockchip's Cryptographic Engine driver"
 	depends on OF && ARCH_ROCKCHIP
+	depends on PM
+	select CRYPTO_ECB
+	select CRYPTO_CBC
+	select CRYPTO_DES
 	select CRYPTO_AES
+	select CRYPTO_ENGINE
 	select CRYPTO_LIB_DES
 	select CRYPTO_MD5
 	select CRYPTO_SHA1
@@ -784,6 +801,39 @@
 	  This driver interfaces with the hardware crypto accelerator.
 	  Supporting cbc/ecb chainmode, and aes/des/des3_ede cipher mode.
 
+config CRYPTO_DEV_ZYNQMP_SHA3
+	tristate "Support for Xilinx ZynqMP SHA3 hardware accelerator"
+	depends on ZYNQMP_FIRMWARE || COMPILE_TEST
+	depends on !CRYPTO_DEV_ZYNQMP_KECCAK_384
+	select CRYPTO_SHA3
+	help
+	  Xilinx ZynqMP has SHA3 engine used for secure hash calculation.
+	  This driver interfaces with SHA3 hardware engine.
+	  Select this if you want to use the ZynqMP module
+	  for SHA3 hash computation.
+
+config CRYPTO_DEV_ZYNQMP_KECCAK_384
+	bool "Support for Xilinx ZynqMP SHA3 hw accelerator(ahash)"
+	default y
+	depends on ARCH_ZYNQMP
+	select CRYPTO_HASH
+	help
+	  Xilinx processors have SHA384 engine used for calculation
+	  of hash. This driver interfaces with SHA3 hw accelerator.
+	  Select this if you want to use the ZynqMP module for
+	  Keccak-SHA384 algorithms.
+
+config CRYPTO_DEV_XILINX_RSA
+	tristate "Support for Xilinx ZynqMP RSA hw accelerator"
+	depends on ARCH_ZYNQMP || COMPILE_TEST
+	select CRYPTO_AES
+	select CRYPTO_BLKCIPHER
+	help
+	  Xilinx processors have RSA hw accelerator used for signature
+	  generation and verification. This driver interfaces with RSA
+	  hw accelerator. Select this if you want to use the ZynqMP module
+	  for RSA algorithms.
+
 config CRYPTO_DEV_ZYNQMP_AES
 	tristate "Support for Xilinx ZynqMP AES hw accelerator"
 	depends on ZYNQMP_FIRMWARE || COMPILE_TEST
@@ -796,6 +846,18 @@
 	  accelerator. Select this if you want to use the ZynqMP module
 	  for AES algorithms.
 
+config CRYPTO_DEV_ZYNQMP_AES_SKCIPHER
+	tristate "Support for Xilinx ZynqMP AES hw accelerator (skcipher)"
+	depends on ZYNQMP_FIRMWARE || COMPILE_TEST
+	depends on !CRYPTO_DEV_ZYNQMP_AES
+	select CRYPTO_AES
+	select CRYPTO_SKCIPHER
+	help
+	  Xilinx ZynqMP has AES-GCM engine used for symmetric key
+	  encryption and decryption. This driver interfaces with AES hw
+	  accelerator. Select this if you want to use the ZynqMP module
+	  for AES algorithms.
+
 source "drivers/crypto/chelsio/Kconfig"
 
 source "drivers/crypto/virtio/Kconfig"
@@ -900,6 +962,7 @@
 	select CRYPTO_AES_ARM64
 	select CRYPTO_ALGAPI
 	select CRYPTO_AUTHENC
+	select CRYPTO_DES
 	select CRYPTO_SHA1
 	select CRYPTO_SHA256
 	select CRYPTO_SHA512
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/Makefile
@@ -47,7 +47,7 @@
 obj-$(CONFIG_CRYPTO_DEV_BCM_SPU) += bcm/
 obj-$(CONFIG_CRYPTO_DEV_SAFEXCEL) += inside-secure/
 obj-$(CONFIG_CRYPTO_DEV_ARTPEC6) += axis/
-obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_AES) += xilinx/
+obj-y += xilinx/
 obj-y += hisilicon/
 obj-$(CONFIG_CRYPTO_DEV_AMLOGIC_GXL) += amlogic/
 obj-y += keembay/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/allwinner/sun8i-ce/sun8i-ce-cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/allwinner/sun8i-ce/sun8i-ce-cipher.c
@@ -11,6 +11,7 @@
  * You could find a link for the datasheet in Documentation/arm/sunxi.rst
  */
 
+#include <linux/bottom_half.h>
 #include <linux/crypto.h>
 #include <linux/dma-mapping.h>
 #include <linux/io.h>
@@ -283,7 +284,9 @@
 
 	flow = rctx->flow;
 	err = sun8i_ce_run_task(ce, flow, crypto_tfm_alg_name(breq->base.tfm));
+	local_bh_disable();
 	crypto_finalize_skcipher_request(engine, breq, err);
+	local_bh_enable();
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/allwinner/sun8i-ce/sun8i-ce-hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/allwinner/sun8i-ce/sun8i-ce-hash.c
@@ -9,6 +9,7 @@
  *
  * You could find the datasheet in Documentation/arm/sunxi.rst
  */
+#include <linux/bottom_half.h>
 #include <linux/dma-mapping.h>
 #include <linux/pm_runtime.h>
 #include <linux/scatterlist.h>
@@ -414,6 +415,8 @@
 theend:
 	kfree(buf);
 	kfree(result);
+	local_bh_disable();
 	crypto_finalize_hash_request(engine, breq, err);
+	local_bh_enable();
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/allwinner/sun8i-ss/sun8i-ss-cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/allwinner/sun8i-ss/sun8i-ss-cipher.c
@@ -11,6 +11,7 @@
  * You could find a link for the datasheet in Documentation/arm/sunxi.rst
  */
 
+#include <linux/bottom_half.h>
 #include <linux/crypto.h>
 #include <linux/dma-mapping.h>
 #include <linux/io.h>
@@ -92,6 +93,69 @@
 	return err;
 }
 
+static int sun8i_ss_setup_ivs(struct skcipher_request *areq)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(areq);
+	struct sun8i_cipher_tfm_ctx *op = crypto_skcipher_ctx(tfm);
+	struct sun8i_ss_dev *ss = op->ss;
+	struct sun8i_cipher_req_ctx *rctx = skcipher_request_ctx(areq);
+	struct scatterlist *sg = areq->src;
+	unsigned int todo, offset;
+	unsigned int len = areq->cryptlen;
+	unsigned int ivsize = crypto_skcipher_ivsize(tfm);
+	struct sun8i_ss_flow *sf = &ss->flows[rctx->flow];
+	int i = 0;
+	dma_addr_t a;
+	int err;
+
+	rctx->ivlen = ivsize;
+	if (rctx->op_dir & SS_DECRYPTION) {
+		offset = areq->cryptlen - ivsize;
+		scatterwalk_map_and_copy(sf->biv, areq->src, offset,
+					 ivsize, 0);
+	}
+
+	/* we need to copy all IVs from source in case DMA is bi-directionnal */
+	while (sg && len) {
+		if (sg_dma_len(sg) == 0) {
+			sg = sg_next(sg);
+			continue;
+		}
+		if (i == 0)
+			memcpy(sf->iv[0], areq->iv, ivsize);
+		a = dma_map_single(ss->dev, sf->iv[i], ivsize, DMA_TO_DEVICE);
+		if (dma_mapping_error(ss->dev, a)) {
+			memzero_explicit(sf->iv[i], ivsize);
+			dev_err(ss->dev, "Cannot DMA MAP IV\n");
+			err = -EFAULT;
+			goto dma_iv_error;
+		}
+		rctx->p_iv[i] = a;
+		/* we need to setup all others IVs only in the decrypt way */
+		if (rctx->op_dir == SS_ENCRYPTION)
+			return 0;
+		todo = min(len, sg_dma_len(sg));
+		len -= todo;
+		i++;
+		if (i < MAX_SG) {
+			offset = sg->length - ivsize;
+			scatterwalk_map_and_copy(sf->iv[i], sg, offset, ivsize, 0);
+		}
+		rctx->niv = i;
+		sg = sg_next(sg);
+	}
+
+	return 0;
+dma_iv_error:
+	i--;
+	while (i >= 0) {
+		dma_unmap_single(ss->dev, rctx->p_iv[i], ivsize, DMA_TO_DEVICE);
+		memzero_explicit(sf->iv[i], ivsize);
+		i--;
+	}
+	return err;
+}
+
 static int sun8i_ss_cipher(struct skcipher_request *areq)
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(areq);
@@ -100,9 +164,9 @@
 	struct sun8i_cipher_req_ctx *rctx = skcipher_request_ctx(areq);
 	struct skcipher_alg *alg = crypto_skcipher_alg(tfm);
 	struct sun8i_ss_alg_template *algt;
+	struct sun8i_ss_flow *sf = &ss->flows[rctx->flow];
 	struct scatterlist *sg;
 	unsigned int todo, len, offset, ivsize;
-	void *backup_iv = NULL;
 	int nr_sgs = 0;
 	int nr_sgd = 0;
 	int err = 0;
@@ -133,30 +197,9 @@
 
 	ivsize = crypto_skcipher_ivsize(tfm);
 	if (areq->iv && crypto_skcipher_ivsize(tfm) > 0) {
-		rctx->ivlen = ivsize;
-		rctx->biv = kzalloc(ivsize, GFP_KERNEL | GFP_DMA);
-		if (!rctx->biv) {
-			err = -ENOMEM;
+		err = sun8i_ss_setup_ivs(areq);
+		if (err)
 			goto theend_key;
-		}
-		if (rctx->op_dir & SS_DECRYPTION) {
-			backup_iv = kzalloc(ivsize, GFP_KERNEL);
-			if (!backup_iv) {
-				err = -ENOMEM;
-				goto theend_key;
-			}
-			offset = areq->cryptlen - ivsize;
-			scatterwalk_map_and_copy(backup_iv, areq->src, offset,
-						 ivsize, 0);
-		}
-		memcpy(rctx->biv, areq->iv, ivsize);
-		rctx->p_iv = dma_map_single(ss->dev, rctx->biv, rctx->ivlen,
-					    DMA_TO_DEVICE);
-		if (dma_mapping_error(ss->dev, rctx->p_iv)) {
-			dev_err(ss->dev, "Cannot DMA MAP IV\n");
-			err = -ENOMEM;
-			goto theend_iv;
-		}
 	}
 	if (areq->src == areq->dst) {
 		nr_sgs = dma_map_sg(ss->dev, areq->src, sg_nents(areq->src),
@@ -242,21 +285,19 @@
 	}
 
 theend_iv:
-	if (rctx->p_iv)
-		dma_unmap_single(ss->dev, rctx->p_iv, rctx->ivlen,
-				 DMA_TO_DEVICE);
-
 	if (areq->iv && ivsize > 0) {
-		if (rctx->biv) {
-			offset = areq->cryptlen - ivsize;
-			if (rctx->op_dir & SS_DECRYPTION) {
-				memcpy(areq->iv, backup_iv, ivsize);
-				kfree_sensitive(backup_iv);
-			} else {
-				scatterwalk_map_and_copy(areq->iv, areq->dst, offset,
-							 ivsize, 0);
-			}
-			kfree(rctx->biv);
+		for (i = 0; i < rctx->niv; i++) {
+			dma_unmap_single(ss->dev, rctx->p_iv[i], ivsize, DMA_TO_DEVICE);
+			memzero_explicit(sf->iv[i], ivsize);
+		}
+
+		offset = areq->cryptlen - ivsize;
+		if (rctx->op_dir & SS_DECRYPTION) {
+			memcpy(areq->iv, sf->biv, ivsize);
+			memzero_explicit(sf->biv, ivsize);
+		} else {
+			scatterwalk_map_and_copy(areq->iv, areq->dst, offset,
+					ivsize, 0);
 		}
 	}
 
@@ -274,7 +315,9 @@
 	struct skcipher_request *breq = container_of(areq, struct skcipher_request, base);
 
 	err = sun8i_ss_cipher(breq);
+	local_bh_disable();
 	crypto_finalize_skcipher_request(engine, breq, err);
+	local_bh_enable();
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/allwinner/sun8i-ss/sun8i-ss-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/allwinner/sun8i-ss/sun8i-ss-core.c
@@ -30,6 +30,8 @@
 static const struct ss_variant ss_a80_variant = {
 	.alg_cipher = { SS_ALG_AES, SS_ALG_DES, SS_ALG_3DES,
 	},
+	.alg_hash = { SS_ID_NOTSUPP, SS_ID_NOTSUPP, SS_ID_NOTSUPP, SS_ID_NOTSUPP,
+	},
 	.op_mode = { SS_OP_ECB, SS_OP_CBC,
 	},
 	.ss_clks = {
@@ -64,6 +66,7 @@
 		      const char *name)
 {
 	int flow = rctx->flow;
+	unsigned int ivlen = rctx->ivlen;
 	u32 v = SS_START;
 	int i;
 
@@ -102,15 +105,14 @@
 		mutex_lock(&ss->mlock);
 		writel(rctx->p_key, ss->base + SS_KEY_ADR_REG);
 
-		if (i == 0) {
-			if (rctx->p_iv)
-				writel(rctx->p_iv, ss->base + SS_IV_ADR_REG);
-		} else {
-			if (rctx->biv) {
-				if (rctx->op_dir == SS_ENCRYPTION)
-					writel(rctx->t_dst[i - 1].addr + rctx->t_dst[i - 1].len * 4 - rctx->ivlen, ss->base + SS_IV_ADR_REG);
+		if (ivlen) {
+			if (rctx->op_dir == SS_ENCRYPTION) {
+				if (i == 0)
+					writel(rctx->p_iv[0], ss->base + SS_IV_ADR_REG);
 				else
-					writel(rctx->t_src[i - 1].addr + rctx->t_src[i - 1].len * 4 - rctx->ivlen, ss->base + SS_IV_ADR_REG);
+					writel(rctx->t_dst[i - 1].addr + rctx->t_dst[i - 1].len * 4 - ivlen, ss->base + SS_IV_ADR_REG);
+			} else {
+				writel(rctx->p_iv[i], ss->base + SS_IV_ADR_REG);
 			}
 		}
 
@@ -462,7 +464,7 @@
  */
 static int allocate_flows(struct sun8i_ss_dev *ss)
 {
-	int i, err;
+	int i, j, err;
 
 	ss->flows = devm_kcalloc(ss->dev, MAXFLOW, sizeof(struct sun8i_ss_flow),
 				 GFP_KERNEL);
@@ -472,6 +474,36 @@
 	for (i = 0; i < MAXFLOW; i++) {
 		init_completion(&ss->flows[i].complete);
 
+		ss->flows[i].biv = devm_kmalloc(ss->dev, AES_BLOCK_SIZE,
+						GFP_KERNEL | GFP_DMA);
+		if (!ss->flows[i].biv) {
+			err = -ENOMEM;
+			goto error_engine;
+		}
+
+		for (j = 0; j < MAX_SG; j++) {
+			ss->flows[i].iv[j] = devm_kmalloc(ss->dev, AES_BLOCK_SIZE,
+							  GFP_KERNEL | GFP_DMA);
+			if (!ss->flows[i].iv[j]) {
+				err = -ENOMEM;
+				goto error_engine;
+			}
+		}
+
+		/* the padding could be up to two block. */
+		ss->flows[i].pad = devm_kmalloc(ss->dev, SHA256_BLOCK_SIZE * 2,
+						GFP_KERNEL | GFP_DMA);
+		if (!ss->flows[i].pad) {
+			err = -ENOMEM;
+			goto error_engine;
+		}
+		ss->flows[i].result = devm_kmalloc(ss->dev, SHA256_DIGEST_SIZE,
+						   GFP_KERNEL | GFP_DMA);
+		if (!ss->flows[i].result) {
+			err = -ENOMEM;
+			goto error_engine;
+		}
+
 		ss->flows[i].engine = crypto_engine_alloc_init(ss->dev, true);
 		if (!ss->flows[i].engine) {
 			dev_err(ss->dev, "Cannot allocate engine\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/allwinner/sun8i-ss/sun8i-ss-hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/allwinner/sun8i-ss/sun8i-ss-hash.c
@@ -9,6 +9,7 @@
  *
  * You could find the datasheet in Documentation/arm/sunxi.rst
  */
+#include <linux/bottom_half.h>
 #include <linux/dma-mapping.h>
 #include <linux/pm_runtime.h>
 #include <linux/scatterlist.h>
@@ -341,18 +342,11 @@
 	if (digestsize == SHA224_DIGEST_SIZE)
 		digestsize = SHA256_DIGEST_SIZE;
 
-	/* the padding could be up to two block. */
-	pad = kzalloc(algt->alg.hash.halg.base.cra_blocksize * 2, GFP_KERNEL | GFP_DMA);
-	if (!pad)
-		return -ENOMEM;
+	result = ss->flows[rctx->flow].result;
+	pad = ss->flows[rctx->flow].pad;
+	memset(pad, 0, algt->alg.hash.halg.base.cra_blocksize * 2);
 	bf = (__le32 *)pad;
 
-	result = kzalloc(digestsize, GFP_KERNEL | GFP_DMA);
-	if (!result) {
-		kfree(pad);
-		return -ENOMEM;
-	}
-
 	for (i = 0; i < MAX_SG; i++) {
 		rctx->t_dst[i].addr = 0;
 		rctx->t_dst[i].len = 0;
@@ -379,13 +373,21 @@
 	}
 
 	len = areq->nbytes;
-	for_each_sg(areq->src, sg, nr_sgs, i) {
+	sg = areq->src;
+	i = 0;
+	while (len > 0 && sg) {
+		if (sg_dma_len(sg) == 0) {
+			sg = sg_next(sg);
+			continue;
+		}
 		rctx->t_src[i].addr = sg_dma_address(sg);
 		todo = min(len, sg_dma_len(sg));
 		rctx->t_src[i].len = todo / 4;
 		len -= todo;
 		rctx->t_dst[i].addr = addr_res;
 		rctx->t_dst[i].len = digestsize / 4;
+		sg = sg_next(sg);
+		i++;
 	}
 	if (len > 0) {
 		dev_err(ss->dev, "remaining len %d\n", len);
@@ -440,8 +442,8 @@
 
 	memcpy(areq->result, result, algt->alg.hash.halg.digestsize);
 theend:
-	kfree(pad);
-	kfree(result);
+	local_bh_disable();
 	crypto_finalize_hash_request(engine, breq, err);
+	local_bh_enable();
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/allwinner/sun8i-ss/sun8i-ss.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/allwinner/sun8i-ss/sun8i-ss.h
@@ -121,11 +121,19 @@
  * @complete:	completion for the current task on this flow
  * @status:	set to 1 by interrupt if task is done
  * @stat_req:	number of request done by this flow
+ * @iv:		list of IV to use for each step
+ * @biv:	buffer which contain the backuped IV
+ * @pad:	padding buffer for hash operations
+ * @result:	buffer for storing the result of hash operations
  */
 struct sun8i_ss_flow {
 	struct crypto_engine *engine;
 	struct completion complete;
 	int status;
+	u8 *iv[MAX_SG];
+	u8 *biv;
+	void *pad;
+	void *result;
 #ifdef CONFIG_CRYPTO_DEV_SUN8I_SS_DEBUG
 	unsigned long stat_req;
 #endif
@@ -164,28 +172,28 @@
  * @t_src:		list of mapped SGs with their size
  * @t_dst:		list of mapped SGs with their size
  * @p_key:		DMA address of the key
- * @p_iv:		DMA address of the IV
+ * @p_iv:		DMA address of the IVs
+ * @niv:		Number of IVs DMA mapped
  * @method:		current algorithm for this request
  * @op_mode:		op_mode for this request
  * @op_dir:		direction (encrypt vs decrypt) for this request
  * @flow:		the flow to use for this request
- * @ivlen:		size of biv
+ * @ivlen:		size of IVs
  * @keylen:		keylen for this request
- * @biv:		buffer which contain the IV
  * @fallback_req:	request struct for invoking the fallback skcipher TFM
  */
 struct sun8i_cipher_req_ctx {
 	struct sginfo t_src[MAX_SG];
 	struct sginfo t_dst[MAX_SG];
 	u32 p_key;
-	u32 p_iv;
+	u32 p_iv[MAX_SG];
+	int niv;
 	u32 method;
 	u32 op_mode;
 	u32 op_dir;
 	int flow;
 	unsigned int ivlen;
 	unsigned int keylen;
-	void *biv;
 	struct skcipher_request fallback_req;   // keep at the end
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/amcc/crypto4xx_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/amcc/crypto4xx_core.c
@@ -522,7 +522,6 @@
 {
 	struct skcipher_request *req;
 	struct scatterlist *dst;
-	dma_addr_t addr;
 
 	req = skcipher_request_cast(pd_uinfo->async_req);
 
@@ -531,8 +530,8 @@
 					  req->cryptlen, req->dst);
 	} else {
 		dst = pd_uinfo->dest_va;
-		addr = dma_map_page(dev->core_dev->device, sg_page(dst),
-				    dst->offset, dst->length, DMA_FROM_DEVICE);
+		dma_unmap_page(dev->core_dev->device, pd->dest, dst->length,
+			       DMA_FROM_DEVICE);
 	}
 
 	if (pd_uinfo->sa_va->sa_command_0.bf.save_iv == SA_SAVE_IV) {
@@ -557,10 +556,9 @@
 	struct ahash_request *ahash_req;
 
 	ahash_req = ahash_request_cast(pd_uinfo->async_req);
-	ctx  = crypto_tfm_ctx(ahash_req->base.tfm);
+	ctx = crypto_ahash_ctx(crypto_ahash_reqtfm(ahash_req));
 
-	crypto4xx_copy_digest_to_dst(ahash_req->result, pd_uinfo,
-				     crypto_tfm_ctx(ahash_req->base.tfm));
+	crypto4xx_copy_digest_to_dst(ahash_req->result, pd_uinfo, ctx);
 	crypto4xx_ret_sg_desc(dev, pd_uinfo);
 
 	if (pd_uinfo->state & PD_ENTRY_BUSY)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/amlogic/amlogic-gxl-cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/amlogic/amlogic-gxl-cipher.c
@@ -265,7 +265,9 @@
 	struct skcipher_request *breq = container_of(areq, struct skcipher_request, base);
 
 	err = meson_cipher(breq);
+	local_bh_disable();
 	crypto_finalize_skcipher_request(engine, breq, err);
+	local_bh_enable();
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/amlogic/amlogic-gxl-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/amlogic/amlogic-gxl-core.c
@@ -237,7 +237,6 @@
 		return err;
 	}
 
-	mc->irqs = devm_kcalloc(mc->dev, MAXFLOW, sizeof(int), GFP_KERNEL);
 	for (i = 0; i < MAXFLOW; i++) {
 		mc->irqs[i] = platform_get_irq(pdev, i);
 		if (mc->irqs[i] < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/amlogic/amlogic-gxl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/amlogic/amlogic-gxl.h
@@ -95,7 +95,7 @@
 	struct device *dev;
 	struct meson_flow *chanlist;
 	atomic_t flow;
-	int *irqs;
+	int irqs[MAXFLOW];
 #ifdef CONFIG_CRYPTO_DEV_AMLOGIC_GXL_DEBUG
 	struct dentry *dbgfs_dir;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/atmel-aes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/atmel-aes.c
@@ -960,6 +960,7 @@
 	ctx = crypto_tfm_ctx(areq->tfm);
 
 	dd->areq = areq;
+	dd->ctx = ctx;
 	start_async = (areq != new_areq);
 	dd->is_async = start_async;
 
@@ -1274,7 +1275,6 @@
 
 	crypto_skcipher_set_reqsize(tfm, sizeof(struct atmel_aes_reqctx));
 	ctx->base.dd = dd;
-	ctx->base.dd->ctx = &ctx->base;
 	ctx->base.start = atmel_aes_start;
 
 	return 0;
@@ -1291,7 +1291,6 @@
 
 	crypto_skcipher_set_reqsize(tfm, sizeof(struct atmel_aes_reqctx));
 	ctx->base.dd = dd;
-	ctx->base.dd->ctx = &ctx->base;
 	ctx->base.start = atmel_aes_ctr_start;
 
 	return 0;
@@ -1783,7 +1782,6 @@
 
 	crypto_aead_set_reqsize(tfm, sizeof(struct atmel_aes_reqctx));
 	ctx->base.dd = dd;
-	ctx->base.dd->ctx = &ctx->base;
 	ctx->base.start = atmel_aes_gcm_start;
 
 	return 0;
@@ -1927,7 +1925,6 @@
 	crypto_skcipher_set_reqsize(tfm, sizeof(struct atmel_aes_reqctx) +
 				    crypto_skcipher_reqsize(ctx->fallback_tfm));
 	ctx->base.dd = dd;
-	ctx->base.dd->ctx = &ctx->base;
 	ctx->base.start = atmel_aes_xts_start;
 
 	return 0;
@@ -2154,7 +2151,6 @@
 	crypto_aead_set_reqsize(tfm, (sizeof(struct atmel_aes_authenc_reqctx) +
 				      auth_reqsize));
 	ctx->base.dd = dd;
-	ctx->base.dd->ctx = &ctx->base;
 	ctx->base.start = atmel_aes_authenc_start;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/bcm/cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/bcm/cipher.c
@@ -2415,6 +2415,7 @@
 
 static int ahash_hmac_init(struct ahash_request *req)
 {
+	int ret;
 	struct iproc_reqctx_s *rctx = ahash_request_ctx(req);
 	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
 	struct iproc_ctx_s *ctx = crypto_ahash_ctx(tfm);
@@ -2424,7 +2425,9 @@
 	flow_log("ahash_hmac_init()\n");
 
 	/* init the context as a hash */
-	ahash_init(req);
+	ret = ahash_init(req);
+	if (ret)
+		return ret;
 
 	if (!spu_no_incr_hash(ctx)) {
 		/* SPU-M can do incr hashing but needs sw for outer HMAC */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/bcm/spu2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/bcm/spu2.c
@@ -495,7 +495,7 @@
 	if (hash_iv_len) {
 		packet_log("  Hash IV Length %u bytes\n", hash_iv_len);
 		packet_dump("  hash IV: ", ptr, hash_iv_len);
-		ptr += ciph_key_len;
+		ptr += hash_iv_len;
 	}
 
 	if (ciph_iv_len) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/caamalg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/caamalg.c
@@ -566,7 +566,8 @@
 	if (keylen != CHACHA_KEY_SIZE + saltlen)
 		return -EINVAL;
 
-	ctx->cdata.key_virt = key;
+	memcpy(ctx->key, key, keylen);
+	ctx->cdata.key_virt = ctx->key;
 	ctx->cdata.keylen = keylen - saltlen;
 
 	return chachapoly_set_sh_desc(aead);
@@ -1533,6 +1534,9 @@
 
 	ret = caam_jr_enqueue(ctx->jrdev, desc, aead_crypt_done, req);
 
+	if (ret == -ENOSPC && engine->retry_support)
+		return ret;
+
 	if (ret != -EINPROGRESS) {
 		aead_unmap(ctx->jrdev, rctx->edesc, req);
 		kfree(rctx->edesc);
@@ -1762,6 +1766,9 @@
 
 	ret = caam_jr_enqueue(ctx->jrdev, desc, skcipher_crypt_done, req);
 
+	if (ret == -ENOSPC && engine->retry_support)
+		return ret;
+
 	if (ret != -EINPROGRESS) {
 		skcipher_unmap(ctx->jrdev, rctx->edesc, req);
 		kfree(rctx->edesc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/caamalg_qi2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/caamalg_qi2.c
@@ -639,7 +639,8 @@
 	if (keylen != CHACHA_KEY_SIZE + saltlen)
 		return -EINVAL;
 
-	ctx->cdata.key_virt = key;
+	memcpy(ctx->key, key, keylen);
+	ctx->cdata.key_virt = ctx->key;
 	ctx->cdata.keylen = keylen - saltlen;
 
 	return chachapoly_set_sh_desc(aead);
@@ -5470,7 +5471,7 @@
 	dpaa2_fd_set_len(&fd, dpaa2_fl_get_len(&req->fd_flt[1]));
 	dpaa2_fd_set_flc(&fd, req->flc_dma);
 
-	ppriv = this_cpu_ptr(priv->ppriv);
+	ppriv = raw_cpu_ptr(priv->ppriv);
 	for (i = 0; i < (priv->dpseci_attr.num_tx_queues << 1); i++) {
 		err = dpaa2_io_service_enqueue_fq(ppriv->dpio, ppriv->req_fqid,
 						  &fd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/caamhash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/caamhash.c
@@ -765,6 +765,9 @@
 
 	ret = caam_jr_enqueue(jrdev, desc, state->ahash_op_done, req);
 
+	if (ret == -ENOSPC && engine->retry_support)
+		return ret;
+
 	if (ret != -EINPROGRESS) {
 		ahash_unmap(jrdev, state->edesc, req, 0);
 		kfree(state->edesc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/caampkc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/caampkc.c
@@ -223,7 +223,9 @@
 		if (len && *buff)
 			break;
 
-		sg_miter_next(&miter);
+		if (!sg_miter_next(&miter))
+			break;
+
 		buff = miter.addr;
 		len = miter.length;
 
@@ -380,6 +382,9 @@
 
 	ret = caam_jr_enqueue(jrdev, desc, req_ctx->akcipher_op_done, req);
 
+	if (ret == -ENOSPC && engine->retry_support)
+		return ret;
+
 	if (ret != -EINPROGRESS) {
 		rsa_pub_unmap(jrdev, req_ctx->edesc, req);
 		rsa_io_unmap(jrdev, req_ctx->edesc, req);
@@ -974,7 +979,7 @@
 	return -ENOMEM;
 }
 
-static void caam_rsa_set_priv_key_form(struct caam_rsa_ctx *ctx,
+static int caam_rsa_set_priv_key_form(struct caam_rsa_ctx *ctx,
 				       struct rsa_key *raw_key)
 {
 	struct caam_rsa_key *rsa_key = &ctx->key;
@@ -983,7 +988,7 @@
 
 	rsa_key->p = caam_read_raw_data(raw_key->p, &p_sz);
 	if (!rsa_key->p)
-		return;
+		return -ENOMEM;
 	rsa_key->p_sz = p_sz;
 
 	rsa_key->q = caam_read_raw_data(raw_key->q, &q_sz);
@@ -1016,7 +1021,7 @@
 
 	rsa_key->priv_form = FORM3;
 
-	return;
+	return 0;
 
 free_dq:
 	kfree_sensitive(rsa_key->dq);
@@ -1030,6 +1035,7 @@
 	kfree_sensitive(rsa_key->q);
 free_p:
 	kfree_sensitive(rsa_key->p);
+	return -ENOMEM;
 }
 
 static int caam_rsa_set_priv_key(struct crypto_akcipher *tfm, const void *key,
@@ -1075,7 +1081,9 @@
 	rsa_key->e_sz = raw_key.e_sz;
 	rsa_key->n_sz = raw_key.n_sz;
 
-	caam_rsa_set_priv_key_form(ctx, &raw_key);
+	ret = caam_rsa_set_priv_key_form(ctx, &raw_key);
+	if (ret)
+		goto err;
 
 	return 0;
 
@@ -1153,16 +1161,27 @@
 int caam_pkc_init(struct device *ctrldev)
 {
 	struct caam_drv_private *priv = dev_get_drvdata(ctrldev);
-	u32 pk_inst;
+	u32 pk_inst, pkha;
 	int err;
 	init_done = false;
 
 	/* Determine public key hardware accelerator presence. */
-	if (priv->era < 10)
+	if (priv->era < 10) {
 		pk_inst = (rd_reg32(&priv->ctrl->perfmon.cha_num_ls) &
 			   CHA_ID_LS_PK_MASK) >> CHA_ID_LS_PK_SHIFT;
-	else
-		pk_inst = rd_reg32(&priv->ctrl->vreg.pkha) & CHA_VER_NUM_MASK;
+	} else {
+		pkha = rd_reg32(&priv->ctrl->vreg.pkha);
+		pk_inst = pkha & CHA_VER_NUM_MASK;
+
+		/*
+		 * Newer CAAMs support partially disabled functionality. If this is the
+		 * case, the number is non-zero, but this bit is set to indicate that
+		 * no encryption or decryption is supported. Only signing and verifying
+		 * is supported.
+		 */
+		if (pkha & CHA_VER_MISC_PKHA_NO_CRYPT)
+			pk_inst = 0;
+	}
 
 	/* Do not register algorithms if PKHA is not present. */
 	if (!pk_inst)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/ctrl.c
@@ -284,6 +284,10 @@
 		const u32 rdsta_if = RDSTA_IF0 << sh_idx;
 		const u32 rdsta_pr = RDSTA_PR0 << sh_idx;
 		const u32 rdsta_mask = rdsta_if | rdsta_pr;
+
+		/* Clear the contents before using the descriptor */
+		memset(desc, 0x00, CAAM_CMD_SZ * 7);
+
 		/*
 		 * If the corresponding bit is set, this state handle
 		 * was initialized by somebody else, so it's left alone.
@@ -327,8 +331,6 @@
 		}
 
 		dev_info(ctrldev, "Instantiated RNG4 SH%d\n", sh_idx);
-		/* Clear the contents before recreating the descriptor */
-		memset(desc, 0x00, CAAM_CMD_SZ * 7);
 	}
 
 	kfree(desc);
@@ -609,6 +611,13 @@
 }
 #endif
 
+static bool needs_entropy_delay_adjustment(void)
+{
+	if (of_machine_is_compatible("fsl,imx6sx"))
+		return true;
+	return false;
+}
+
 /* Probe routine for CAAM top (controller) level */
 static int caam_probe(struct platform_device *pdev)
 {
@@ -855,6 +864,8 @@
 			 * Also, if a handle was instantiated, do not change
 			 * the TRNG parameters.
 			 */
+			if (needs_entropy_delay_adjustment())
+				ent_delay = 12000;
 			if (!(ctrlpriv->rng4_sh_init || inst_handles)) {
 				dev_info(dev,
 					 "Entropy delay = %u\n",
@@ -871,6 +882,15 @@
 			 */
 			ret = instantiate_rng(dev, inst_handles,
 					      gen_sk);
+			/*
+			 * Entropy delay is determined via TRNG characterization.
+			 * TRNG characterization is run across different voltages
+			 * and temperatures.
+			 * If worst case value for ent_dly is identified,
+			 * the loop can be skipped for that platform.
+			 */
+			if (needs_entropy_delay_adjustment())
+				break;
 			if (ret == -EAGAIN)
 				/*
 				 * if here, the loop will rerun,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/qi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/qi.c
@@ -765,7 +765,7 @@
 
 	caam_debugfs_qi_init(ctrlpriv);
 
-	err = devm_add_action_or_reset(qidev, caam_qi_shutdown, ctrlpriv);
+	err = devm_add_action_or_reset(qidev, caam_qi_shutdown, qidev);
 	if (err)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/caam/regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/caam/regs.h
@@ -322,6 +322,9 @@
 /* CHA Miscellaneous Information - AESA_MISC specific */
 #define CHA_VER_MISC_AES_GCM	BIT(1 + CHA_VER_MISC_SHIFT)
 
+/* CHA Miscellaneous Information - PKHA_MISC specific */
+#define CHA_VER_MISC_PKHA_NO_CRYPT	BIT(7 + CHA_VER_MISC_SHIFT)
+
 /*
  * caam_perfmon - Performance Monitor/Secure Memory Status/
  *                CAAM Global Status/Component Version IDs
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/cavium/cpt/cptpf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/cavium/cpt/cptpf_main.c
@@ -44,7 +44,7 @@
 		dev_err(dev, "Cores still busy %llx", coremask);
 		grp = cpt_read_csr64(cpt->reg_base,
 				     CPTX_PF_EXEC_BUSY(0));
-		if (timeout--)
+		if (!timeout--)
 			break;
 
 		udelay(CSR_DELAY);
@@ -253,6 +253,7 @@
 	const struct firmware *fw_entry;
 	struct device *dev = &cpt->pdev->dev;
 	struct ucode_header *ucode;
+	unsigned int code_length;
 	struct microcode *mcode;
 	int j, ret = 0;
 
@@ -263,11 +264,12 @@
 	ucode = (struct ucode_header *)fw_entry->data;
 	mcode = &cpt->mcode[cpt->next_mc_idx];
 	memcpy(mcode->version, (u8 *)fw_entry->data, CPT_UCODE_VERSION_SZ);
-	mcode->code_size = ntohl(ucode->code_length) * 2;
-	if (!mcode->code_size) {
+	code_length = ntohl(ucode->code_length);
+	if (code_length == 0 || code_length >= INT_MAX / 2) {
 		ret = -EINVAL;
 		goto fw_release;
 	}
+	mcode->code_size = code_length * 2;
 
 	mcode->is_ae = is_ae;
 	mcode->core_mask = 0ULL;
@@ -300,6 +302,8 @@
 
 	ret = do_cpt_init(cpt, mcode);
 	if (ret) {
+		dma_free_coherent(&cpt->pdev->dev, mcode->code_size,
+				  mcode->code, mcode->phys_base);
 		dev_err(dev, "do_cpt_init failed with ret: %d\n", ret);
 		goto fw_release;
 	}
@@ -392,7 +396,7 @@
 		dev_err(dev, "Cores still busy");
 		grp = cpt_read_csr64(cpt->reg_base,
 				     CPTX_PF_EXEC_BUSY(0));
-		if (timeout--)
+		if (!timeout--)
 			break;
 
 		udelay(CSR_DELAY);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/cavium/nitrox/nitrox_mbx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/cavium/nitrox/nitrox_mbx.c
@@ -191,6 +191,7 @@
 	ndev->iov.pf2vf_wq = alloc_workqueue("nitrox_pf2vf", 0, 0);
 	if (!ndev->iov.pf2vf_wq) {
 		kfree(ndev->iov.vfdev);
+		ndev->iov.vfdev = NULL;
 		return -ENOMEM;
 	}
 	/* enable pf2vf mailbox interrupts */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccp/ccp-dmaengine.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccp/ccp-dmaengine.c
@@ -632,6 +632,36 @@
 	return 0;
 }
 
+static void ccp_dma_release(struct ccp_device *ccp)
+{
+	struct ccp_dma_chan *chan;
+	struct dma_chan *dma_chan;
+	unsigned int i;
+
+	for (i = 0; i < ccp->cmd_q_count; i++) {
+		chan = ccp->ccp_dma_chan + i;
+		dma_chan = &chan->dma_chan;
+
+		tasklet_kill(&chan->cleanup_tasklet);
+		list_del_rcu(&dma_chan->device_node);
+	}
+}
+
+static void ccp_dma_release_channels(struct ccp_device *ccp)
+{
+	struct ccp_dma_chan *chan;
+	struct dma_chan *dma_chan;
+	unsigned int i;
+
+	for (i = 0; i < ccp->cmd_q_count; i++) {
+		chan = ccp->ccp_dma_chan + i;
+		dma_chan = &chan->dma_chan;
+
+		if (dma_chan->client_count)
+			dma_release_channel(dma_chan);
+	}
+}
+
 int ccp_dmaengine_register(struct ccp_device *ccp)
 {
 	struct ccp_dma_chan *chan;
@@ -736,6 +766,7 @@
 	return 0;
 
 err_reg:
+	ccp_dma_release(ccp);
 	kmem_cache_destroy(ccp->dma_desc_cache);
 
 err_cache:
@@ -751,7 +782,9 @@
 	if (!dmaengine)
 		return;
 
+	ccp_dma_release_channels(ccp);
 	dma_async_device_unregister(dma_dev);
+	ccp_dma_release(ccp);
 
 	kmem_cache_destroy(ccp->dma_desc_cache);
 	kmem_cache_destroy(ccp->dma_cmd_cache);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccp/ccp-ops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccp/ccp-ops.c
@@ -179,8 +179,11 @@
 
 		wa->dma.address = dma_map_single(wa->dev, wa->address, len,
 						 dir);
-		if (dma_mapping_error(wa->dev, wa->dma.address))
+		if (dma_mapping_error(wa->dev, wa->dma.address)) {
+			kfree(wa->address);
+			wa->address = NULL;
 			return -ENOMEM;
+		}
 
 		wa->dma.length = len;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccp/psp-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccp/psp-dev.c
@@ -42,6 +42,9 @@
 	/* Read the interrupt status: */
 	status = ioread32(psp->io_regs + psp->vdata->intsts_reg);
 
+	/* Clear the interrupt status by writing the same value we read. */
+	iowrite32(status, psp->io_regs + psp->vdata->intsts_reg);
+
 	/* invoke subdevice interrupt handlers */
 	if (status) {
 		if (psp->sev_irq_handler)
@@ -51,9 +54,6 @@
 			psp->tee_irq_handler(irq, psp->tee_irq_data, status);
 	}
 
-	/* Clear the interrupt status by writing the same value we read. */
-	iowrite32(status, psp->io_regs + psp->vdata->intsts_reg);
-
 	return IRQ_HANDLED;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccp/sev-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccp/sev-dev.c
@@ -24,6 +24,7 @@
 #include <linux/cpufeature.h>
 
 #include <asm/smp.h>
+#include <asm/cacheflush.h>
 
 #include "psp-dev.h"
 #include "sev-dev.h"
@@ -141,6 +142,17 @@
 	return 0;
 }
 
+static void *sev_fw_alloc(unsigned long len)
+{
+	struct page *page;
+
+	page = alloc_pages(GFP_KERNEL, get_order(len));
+	if (!page)
+		return NULL;
+
+	return page_address(page);
+}
+
 static int __sev_do_cmd_locked(int cmd, void *data, int *psp_ret)
 {
 	struct psp_device *psp = psp_master;
@@ -241,7 +253,7 @@
 	struct psp_device *psp = psp_master;
 	struct sev_data_init data;
 	struct sev_device *sev;
-	int rc = 0;
+	int psp_ret = -1, rc = 0;
 
 	if (!psp || !psp->sev_data)
 		return -ENODEV;
@@ -266,7 +278,21 @@
 		data.tmr_len = SEV_ES_TMR_SIZE;
 	}
 
-	rc = __sev_do_cmd_locked(SEV_CMD_INIT, &data, error);
+	rc = __sev_do_cmd_locked(SEV_CMD_INIT, &data, &psp_ret);
+	if (rc && psp_ret == SEV_RET_SECURE_DATA_INVALID) {
+		/*
+		 * Initialization command returned an integrity check failure
+		 * status code, meaning that firmware load and validation of SEV
+		 * related persistent data has failed. Retrying the
+		 * initialization function should succeed by replacing the state
+		 * with a reset state.
+		 */
+		dev_dbg(sev->dev, "SEV: retrying INIT command");
+		rc = __sev_do_cmd_locked(SEV_CMD_INIT, &data, &psp_ret);
+	}
+	if (error)
+		*error = psp_ret;
+
 	if (rc)
 		return rc;
 
@@ -297,9 +323,15 @@
 
 static int __sev_platform_shutdown_locked(int *error)
 {
-	struct sev_device *sev = psp_master->sev_data;
+	struct psp_device *psp = psp_master;
+	struct sev_device *sev;
 	int ret;
 
+	if (!psp || !psp->sev_data)
+		return 0;
+
+	sev = psp->sev_data;
+
 	if (sev->state == SEV_STATE_UNINIT)
 		return 0;
 
@@ -374,6 +406,8 @@
 	struct sev_user_data_status data;
 	int ret;
 
+	memset(&data, 0, sizeof(data));
+
 	ret = __sev_do_cmd_locked(SEV_CMD_PLATFORM_STATUS, &data, &argp->error);
 	if (ret)
 		return ret;
@@ -427,7 +461,7 @@
 	if (input.length > SEV_FW_BLOB_MAX_SIZE)
 		return -EFAULT;
 
-	blob = kmalloc(input.length, GFP_KERNEL);
+	blob = kzalloc(input.length, GFP_KERNEL);
 	if (!blob)
 		return -ENOMEM;
 
@@ -651,7 +685,14 @@
 	input_address = (void __user *)input.address;
 
 	if (input.address && input.length) {
-		id_blob = kmalloc(input.length, GFP_KERNEL);
+		/*
+		 * The length of the ID shouldn't be assumed by software since
+		 * it may change in the future.  The allocation size is limited
+		 * to 1 << (PAGE_SHIFT + MAX_ORDER - 1) by the page allocator.
+		 * If the allocation fails, simply return ENOMEM rather than
+		 * warning in the kernel log.
+		 */
+		id_blob = kzalloc(input.length, GFP_KERNEL | __GFP_NOWARN);
 		if (!id_blob)
 			return -ENOMEM;
 
@@ -770,14 +811,14 @@
 	if (input.cert_chain_len > SEV_FW_BLOB_MAX_SIZE)
 		return -EFAULT;
 
-	pdh_blob = kmalloc(input.pdh_cert_len, GFP_KERNEL);
+	pdh_blob = kzalloc(input.pdh_cert_len, GFP_KERNEL);
 	if (!pdh_blob)
 		return -ENOMEM;
 
 	data.pdh_cert_address = __psp_pa(pdh_blob);
 	data.pdh_cert_len = input.pdh_cert_len;
 
-	cert_blob = kmalloc(input.cert_chain_len, GFP_KERNEL);
+	cert_blob = kzalloc(input.cert_chain_len, GFP_KERNEL);
 	if (!cert_blob) {
 		ret = -ENOMEM;
 		goto e_free_pdh;
@@ -1064,7 +1105,6 @@
 void sev_pci_init(void)
 {
 	struct sev_device *sev = psp_master->sev_data;
-	struct page *tmr_page;
 	int error, rc;
 
 	if (!sev)
@@ -1080,29 +1120,16 @@
 		sev_get_api_version();
 
 	/* Obtain the TMR memory area for SEV-ES use */
-	tmr_page = alloc_pages(GFP_KERNEL, get_order(SEV_ES_TMR_SIZE));
-	if (tmr_page) {
-		sev_es_tmr = page_address(tmr_page);
-	} else {
-		sev_es_tmr = NULL;
+	sev_es_tmr = sev_fw_alloc(SEV_ES_TMR_SIZE);
+	if (sev_es_tmr)
+		/* Must flush the cache before giving it to the firmware */
+		clflush_cache_range(sev_es_tmr, SEV_ES_TMR_SIZE);
+	else
 		dev_warn(sev->dev,
 			 "SEV: TMR allocation failed, SEV-ES support unavailable\n");
-	}
 
 	/* Initialize the platform */
 	rc = sev_platform_init(&error);
-	if (rc && (error == SEV_RET_SECURE_DATA_INVALID)) {
-		/*
-		 * INIT command returned an integrity check failure
-		 * status code, meaning that firmware load and
-		 * validation of SEV related persistent data has
-		 * failed and persistent state has been erased.
-		 * Retrying INIT command here should succeed.
-		 */
-		dev_dbg(sev->dev, "SEV: retrying INIT command");
-		rc = sev_platform_init(&error);
-	}
-
 	if (rc) {
 		dev_err(sev->dev, "SEV: failed to INIT error %#x\n", error);
 		return;
@@ -1114,6 +1141,8 @@
 	return;
 
 err:
+	sev_dev_destroy(psp_master);
+
 	psp_master->sev_data = NULL;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccp/sp-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccp/sp-pci.c
@@ -320,6 +320,15 @@
 	.inten_reg		= 0x10690,
 	.intsts_reg		= 0x10694,
 };
+
+static const struct psp_vdata pspv4 = {
+	.sev			= &sevv2,
+	.tee			= &teev1,
+	.feature_reg		= 0x109fc,
+	.inten_reg		= 0x10690,
+	.intsts_reg		= 0x10694,
+};
+
 #endif
 
 static const struct sp_dev_vdata dev_vdata[] = {
@@ -365,7 +374,7 @@
 	{	/* 5 */
 		.bar = 2,
 #ifdef CONFIG_CRYPTO_DEV_SP_PSP
-		.psp_vdata = &pspv2,
+		.psp_vdata = &pspv4,
 #endif
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccp/sp-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccp/sp-platform.c
@@ -39,44 +39,38 @@
 	},
 };
 
-#ifdef CONFIG_ACPI
 static const struct acpi_device_id sp_acpi_match[] = {
 	{ "AMDI0C00", (kernel_ulong_t)&dev_vdata[0] },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, sp_acpi_match);
-#endif
 
-#ifdef CONFIG_OF
 static const struct of_device_id sp_of_match[] = {
 	{ .compatible = "amd,ccp-seattle-v1a",
 	  .data = (const void *)&dev_vdata[0] },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, sp_of_match);
-#endif
 
 static struct sp_dev_vdata *sp_get_of_version(struct platform_device *pdev)
 {
-#ifdef CONFIG_OF
 	const struct of_device_id *match;
 
 	match = of_match_node(sp_of_match, pdev->dev.of_node);
 	if (match && match->data)
 		return (struct sp_dev_vdata *)match->data;
-#endif
+
 	return NULL;
 }
 
 static struct sp_dev_vdata *sp_get_acpi_version(struct platform_device *pdev)
 {
-#ifdef CONFIG_ACPI
 	const struct acpi_device_id *match;
 
 	match = acpi_match_device(sp_acpi_match, &pdev->dev);
 	if (match && match->driver_data)
 		return (struct sp_dev_vdata *)match->driver_data;
-#endif
+
 	return NULL;
 }
 
@@ -222,12 +216,8 @@
 static struct platform_driver sp_platform_driver = {
 	.driver = {
 		.name = "ccp",
-#ifdef CONFIG_ACPI
 		.acpi_match_table = sp_acpi_match,
-#endif
-#ifdef CONFIG_OF
 		.of_match_table = sp_of_match,
-#endif
 	},
 	.probe = sp_platform_probe,
 	.remove = sp_platform_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccree/cc_buffer_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccree/cc_buffer_mgr.c
@@ -258,6 +258,13 @@
 {
 	int ret = 0;
 
+	if (!nbytes) {
+		*mapped_nents = 0;
+		*lbytes = 0;
+		*nents = 0;
+		return 0;
+	}
+
 	*nents = cc_get_sgl_nents(dev, sg, nbytes, lbytes);
 	if (*nents > max_sg_nents) {
 		*nents = 0;
@@ -349,12 +356,14 @@
 			      req_ctx->mlli_params.mlli_dma_addr);
 	}
 
-	dma_unmap_sg(dev, src, req_ctx->in_nents, DMA_BIDIRECTIONAL);
-	dev_dbg(dev, "Unmapped req->src=%pK\n", sg_virt(src));
-
 	if (src != dst) {
-		dma_unmap_sg(dev, dst, req_ctx->out_nents, DMA_BIDIRECTIONAL);
+		dma_unmap_sg(dev, src, req_ctx->in_nents, DMA_TO_DEVICE);
+		dma_unmap_sg(dev, dst, req_ctx->out_nents, DMA_FROM_DEVICE);
 		dev_dbg(dev, "Unmapped req->dst=%pK\n", sg_virt(dst));
+		dev_dbg(dev, "Unmapped req->src=%pK\n", sg_virt(src));
+	} else {
+		dma_unmap_sg(dev, src, req_ctx->in_nents, DMA_BIDIRECTIONAL);
+		dev_dbg(dev, "Unmapped req->src=%pK\n", sg_virt(src));
 	}
 }
 
@@ -370,6 +379,7 @@
 	u32 dummy = 0;
 	int rc = 0;
 	u32 mapped_nents = 0;
+	int src_direction = (src != dst ? DMA_TO_DEVICE : DMA_BIDIRECTIONAL);
 
 	req_ctx->dma_buf_type = CC_DMA_BUF_DLLI;
 	mlli_params->curr_pool = NULL;
@@ -392,7 +402,7 @@
 	}
 
 	/* Map the src SGL */
-	rc = cc_map_sg(dev, src, nbytes, DMA_BIDIRECTIONAL, &req_ctx->in_nents,
+	rc = cc_map_sg(dev, src, nbytes, src_direction, &req_ctx->in_nents,
 		       LLI_MAX_NUM_OF_DATA_ENTRIES, &dummy, &mapped_nents);
 	if (rc)
 		goto cipher_exit;
@@ -409,7 +419,7 @@
 		}
 	} else {
 		/* Map the dst sg */
-		rc = cc_map_sg(dev, dst, nbytes, DMA_BIDIRECTIONAL,
+		rc = cc_map_sg(dev, dst, nbytes, DMA_FROM_DEVICE,
 			       &req_ctx->out_nents, LLI_MAX_NUM_OF_DATA_ENTRIES,
 			       &dummy, &mapped_nents);
 		if (rc)
@@ -449,6 +459,7 @@
 	struct aead_req_ctx *areq_ctx = aead_request_ctx(req);
 	unsigned int hw_iv_size = areq_ctx->hw_iv_size;
 	struct cc_drvdata *drvdata = dev_get_drvdata(dev);
+	int src_direction = (req->src != req->dst ? DMA_TO_DEVICE : DMA_BIDIRECTIONAL);
 
 	if (areq_ctx->mac_buf_dma_addr) {
 		dma_unmap_single(dev, areq_ctx->mac_buf_dma_addr,
@@ -507,13 +518,11 @@
 		sg_virt(req->src), areq_ctx->src.nents, areq_ctx->assoc.nents,
 		areq_ctx->assoclen, req->cryptlen);
 
-	dma_unmap_sg(dev, req->src, areq_ctx->src.mapped_nents,
-		     DMA_BIDIRECTIONAL);
+	dma_unmap_sg(dev, req->src, areq_ctx->src.mapped_nents, src_direction);
 	if (req->src != req->dst) {
 		dev_dbg(dev, "Unmapping dst sgl: req->dst=%pK\n",
 			sg_virt(req->dst));
-		dma_unmap_sg(dev, req->dst, areq_ctx->dst.mapped_nents,
-			     DMA_BIDIRECTIONAL);
+		dma_unmap_sg(dev, req->dst, areq_ctx->dst.mapped_nents, DMA_FROM_DEVICE);
 	}
 	if (drvdata->coherent &&
 	    areq_ctx->gen_ctx.op_type == DRV_CRYPTO_DIRECTION_DECRYPT &&
@@ -836,7 +845,7 @@
 		else
 			size_for_map -= authsize;
 
-		rc = cc_map_sg(dev, req->dst, size_for_map, DMA_BIDIRECTIONAL,
+		rc = cc_map_sg(dev, req->dst, size_for_map, DMA_FROM_DEVICE,
 			       &areq_ctx->dst.mapped_nents,
 			       LLI_MAX_NUM_OF_DATA_ENTRIES, &dst_last_bytes,
 			       &dst_mapped_nents);
@@ -1049,7 +1058,8 @@
 		size_to_map += authsize;
 	}
 
-	rc = cc_map_sg(dev, req->src, size_to_map, DMA_BIDIRECTIONAL,
+	rc = cc_map_sg(dev, req->src, size_to_map,
+		       (req->src != req->dst ? DMA_TO_DEVICE : DMA_BIDIRECTIONAL),
 		       &areq_ctx->src.mapped_nents,
 		       (LLI_MAX_NUM_OF_ASSOC_DATA_ENTRIES +
 			LLI_MAX_NUM_OF_DATA_ENTRIES),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccree/cc_cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccree/cc_cipher.c
@@ -257,8 +257,8 @@
 		&ctx_p->user.key_dma_addr);
 
 	/* Free key buffer in context */
-	kfree_sensitive(ctx_p->user.key);
 	dev_dbg(dev, "Free key buffer in context. key=@%p\n", ctx_p->user.key);
+	kfree_sensitive(ctx_p->user.key);
 }
 
 struct tdes_keys {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccree/cc_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccree/cc_debugfs.c
@@ -55,7 +55,7 @@
 	cc_debugfs_dir = debugfs_create_dir("ccree", NULL);
 }
 
-void __exit cc_debugfs_global_fini(void)
+void cc_debugfs_global_fini(void)
 {
 	debugfs_remove(cc_debugfs_dir);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ccree/cc_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ccree/cc_driver.c
@@ -103,7 +103,8 @@
 static void init_cc_cache_params(struct cc_drvdata *drvdata)
 {
 	struct device *dev = drvdata_to_dev(drvdata);
-	u32 cache_params, ace_const, val, mask;
+	u32 cache_params, ace_const, val;
+	u64 mask;
 
 	/* compute CC_AXIM_CACHE_PARAMS */
 	cache_params = cc_ioread(drvdata, CC_REG(AXIM_CACHE_PARAMS));
@@ -655,9 +656,17 @@
 
 static int __init ccree_init(void)
 {
+	int rc;
+
 	cc_debugfs_global_init();
 
-	return platform_driver_register(&ccree_driver);
+	rc = platform_driver_register(&ccree_driver);
+	if (rc) {
+		cc_debugfs_global_fini();
+		return rc;
+	}
+
+	return 0;
 }
 module_init(ccree_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/gemini/sl3516-ce-cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/gemini/sl3516-ce-cipher.c
@@ -264,7 +264,9 @@
 	struct skcipher_request *breq = container_of(areq, struct skcipher_request, base);
 
 	err = sl3516_ce_cipher(breq);
+	local_bh_disable();
 	crypto_finalize_skcipher_request(engine, breq, err);
+	local_bh_enable();
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/hpre/hpre_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/hpre/hpre_crypto.c
@@ -252,7 +252,7 @@
 	if (unlikely(shift < 0))
 		return -EINVAL;
 
-	ptr = dma_alloc_coherent(dev, ctx->key_sz, tmp, GFP_KERNEL);
+	ptr = dma_alloc_coherent(dev, ctx->key_sz, tmp, GFP_ATOMIC);
 	if (unlikely(!ptr))
 		return -ENOMEM;
 
@@ -1865,7 +1865,7 @@
 	 */
 	if (memcmp(ptr, p, ctx->key_sz) == 0) {
 		dev_err(dev, "gx is p!\n");
-		return -EINVAL;
+		goto err;
 	} else if (memcmp(ptr, p, ctx->key_sz) > 0) {
 		hpre_curve25519_src_modulo_p(ptr);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/hpre/hpre_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/hpre/hpre_main.c
@@ -854,7 +854,7 @@
 
 	for (i = 0; i < clusters_num; i++) {
 		ret = snprintf(buf, HPRE_DBGFS_VAL_MAX_LEN, "cluster%d", i);
-		if (ret < 0)
+		if (ret >= HPRE_DBGFS_VAL_MAX_LEN)
 			return -EINVAL;
 		tmp_d = debugfs_create_dir(buf, qm->debug.debug_root);
 
@@ -1143,18 +1143,12 @@
 static void hpre_remove(struct pci_dev *pdev)
 {
 	struct hisi_qm *qm = pci_get_drvdata(pdev);
-	int ret;
 
 	hisi_qm_pm_uninit(qm);
 	hisi_qm_wait_task_finish(qm, &hpre_devices);
 	hisi_qm_alg_unregister(qm, &hpre_devices);
-	if (qm->fun_type == QM_HW_PF && qm->vfs_num) {
-		ret = hisi_qm_sriov_disable(pdev, true);
-		if (ret) {
-			pci_err(pdev, "Disable SRIOV fail!\n");
-			return;
-		}
-	}
+	if (qm->fun_type == QM_HW_PF && qm->vfs_num)
+		hisi_qm_sriov_disable(pdev, true);
 
 	hpre_debugfs_exit(qm);
 	hisi_qm_stop(qm, QM_NORMAL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/qm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/qm.c
@@ -1888,8 +1888,10 @@
 		return ret;
 
 	/* Judge if the instance is being reset. */
-	if (unlikely(atomic_read(&qm->status.flags) == QM_STOP))
-		return 0;
+	if (unlikely(atomic_read(&qm->status.flags) == QM_STOP)) {
+		ret = 0;
+		goto put_dfx_access;
+	}
 
 	if (count > QM_DBG_WRITE_LEN) {
 		ret = -ENOSPC;
@@ -3094,7 +3096,7 @@
 	if (IS_ERR(uacce))
 		return PTR_ERR(uacce);
 
-	if (uacce->flags & UACCE_DEV_SVA && qm->mode == UACCE_MODE_SVA) {
+	if (uacce->flags & UACCE_DEV_SVA) {
 		qm->use_sva = true;
 	} else {
 		/* only consider sva case */
@@ -3367,8 +3369,10 @@
 
 	qm_irq_unregister(qm);
 	hisi_qm_pci_uninit(qm);
-	uacce_remove(qm->uacce);
-	qm->uacce = NULL;
+	if (qm->use_sva) {
+		uacce_remove(qm->uacce);
+		qm->uacce = NULL;
+	}
 
 	up_write(&qm->qps_lock);
 }
@@ -4107,7 +4111,7 @@
 static int qm_vf_read_qos(struct hisi_qm *qm)
 {
 	int cnt = 0;
-	int ret;
+	int ret = -EINVAL;
 
 	/* reset mailbox qos val */
 	qm->mb_qos = 0;
@@ -4636,6 +4640,28 @@
 	return -ETIMEDOUT;
 }
 
+static void qm_dev_ecc_mbit_handle(struct hisi_qm *qm)
+{
+	u32 nfe_enb = 0;
+
+	/* Kunpeng930 hardware automatically close master ooo when NFE occurs */
+	if (qm->ver >= QM_HW_V3)
+		return;
+
+	if (!qm->err_status.is_dev_ecc_mbit &&
+	    qm->err_status.is_qm_ecc_mbit &&
+	    qm->err_ini->close_axi_master_ooo) {
+		qm->err_ini->close_axi_master_ooo(qm);
+	} else if (qm->err_status.is_dev_ecc_mbit &&
+		   !qm->err_status.is_qm_ecc_mbit &&
+		   !qm->err_ini->close_axi_master_ooo) {
+		nfe_enb = readl(qm->io_base + QM_RAS_NFE_ENABLE);
+		writel(nfe_enb & QM_RAS_NFE_MBIT_DISABLE,
+		       qm->io_base + QM_RAS_NFE_ENABLE);
+		writel(QM_ECC_MBIT, qm->io_base + QM_ABNORMAL_INT_SET);
+	}
+}
+
 static int qm_vf_reset_prepare(struct hisi_qm *qm,
 			       enum qm_stop_reason stop_reason)
 {
@@ -4740,6 +4766,8 @@
 		return ret;
 	}
 
+	qm_dev_ecc_mbit_handle(qm);
+
 	/* PF obtains the information of VF by querying the register. */
 	qm_cmd_uninit(qm);
 
@@ -4764,31 +4792,6 @@
 	return 0;
 }
 
-static void qm_dev_ecc_mbit_handle(struct hisi_qm *qm)
-{
-	u32 nfe_enb = 0;
-
-	/* Kunpeng930 hardware automatically close master ooo when NFE occurs */
-	if (qm->ver >= QM_HW_V3)
-		return;
-
-	if (!qm->err_status.is_dev_ecc_mbit &&
-	    qm->err_status.is_qm_ecc_mbit &&
-	    qm->err_ini->close_axi_master_ooo) {
-
-		qm->err_ini->close_axi_master_ooo(qm);
-
-	} else if (qm->err_status.is_dev_ecc_mbit &&
-		   !qm->err_status.is_qm_ecc_mbit &&
-		   !qm->err_ini->close_axi_master_ooo) {
-
-		nfe_enb = readl(qm->io_base + QM_RAS_NFE_ENABLE);
-		writel(nfe_enb & QM_RAS_NFE_MBIT_DISABLE,
-		       qm->io_base + QM_RAS_NFE_ENABLE);
-		writel(QM_ECC_MBIT, qm->io_base + QM_ABNORMAL_INT_SET);
-	}
-}
-
 static int qm_soft_reset(struct hisi_qm *qm)
 {
 	struct pci_dev *pdev = qm->pdev;
@@ -4814,8 +4817,6 @@
 		return ret;
 	}
 
-	qm_dev_ecc_mbit_handle(qm);
-
 	/* OOO register set and check */
 	writel(ACC_MASTER_GLOBAL_CTRL_SHUTDOWN,
 	       qm->io_base + ACC_MASTER_GLOBAL_CTRL);
@@ -5725,8 +5726,8 @@
 					 GFP_ATOMIC);
 	dev_dbg(dev, "allocate qm dma buf size=%zx)\n", qm->qdma.size);
 	if (!qm->qdma.va) {
-		ret =  -ENOMEM;
-		goto err_alloc_qdma;
+		ret = -ENOMEM;
+		goto err_destroy_idr;
 	}
 
 	QM_INIT_BUF(qm, eqe, QM_EQ_DEPTH);
@@ -5742,7 +5743,8 @@
 
 err_alloc_qp_array:
 	dma_free_coherent(dev, qm->qdma.size, qm->qdma.va, qm->qdma.dma);
-err_alloc_qdma:
+err_destroy_idr:
+	idr_destroy(&qm->qp_idr);
 	kfree(qm->factor);
 
 	return ret;
@@ -5777,9 +5779,11 @@
 			goto err_irq_register;
 	}
 
-	ret = qm_alloc_uacce(qm);
-	if (ret < 0)
-		dev_warn(dev, "fail to alloc uacce (%d)\n", ret);
+	if (qm->mode == UACCE_MODE_SVA) {
+		ret = qm_alloc_uacce(qm);
+		if (ret < 0)
+			dev_warn(dev, "fail to alloc uacce (%d)\n", ret);
+	}
 
 	ret = hisi_qm_memory_init(qm);
 	if (ret)
@@ -5792,8 +5796,10 @@
 	return 0;
 
 err_alloc_uacce:
-	uacce_remove(qm->uacce);
-	qm->uacce = NULL;
+	if (qm->use_sva) {
+		uacce_remove(qm->uacce);
+		qm->uacce = NULL;
+	}
 err_irq_register:
 	qm_irq_unregister(qm);
 err_pci_init:
@@ -5986,7 +5992,7 @@
 	if (ret)
 		pci_err(pdev, "failed to start qm(%d)\n", ret);
 
-	return 0;
+	return ret;
 }
 EXPORT_SYMBOL_GPL(hisi_qm_resume);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/qm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/qm.h
@@ -318,14 +318,14 @@
 static inline int q_num_set(const char *val, const struct kernel_param *kp,
 			    unsigned int device)
 {
-	struct pci_dev *pdev = pci_get_device(PCI_VENDOR_ID_HUAWEI,
-					      device, NULL);
+	struct pci_dev *pdev;
 	u32 n, q_num;
 	int ret;
 
 	if (!val)
 		return -EINVAL;
 
+	pdev = pci_get_device(PCI_VENDOR_ID_HUAWEI, device, NULL);
 	if (!pdev) {
 		q_num = min_t(u32, QM_QNUM_V1, QM_QNUM_V2);
 		pr_info("No device found currently, suppose queue number is %u\n",
@@ -335,6 +335,8 @@
 			q_num = QM_QNUM_V1;
 		else
 			q_num = QM_QNUM_V2;
+
+		pci_dev_put(pdev);
 	}
 
 	ret = kstrtou32(val, 10, &n);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sec/sec_algs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sec/sec_algs.c
@@ -449,7 +449,7 @@
 		 */
 	}
 
-	mutex_lock(&ctx->queue->queuelock);
+	spin_lock_bh(&ctx->queue->queuelock);
 	/* Put the IV in place for chained cases */
 	switch (ctx->cipher_alg) {
 	case SEC_C_AES_CBC_128:
@@ -509,7 +509,7 @@
 			list_del(&backlog_req->backlog_head);
 		}
 	}
-	mutex_unlock(&ctx->queue->queuelock);
+	spin_unlock_bh(&ctx->queue->queuelock);
 
 	mutex_lock(&sec_req->lock);
 	list_del(&sec_req_el->head);
@@ -798,7 +798,7 @@
 	 */
 
 	/* Grab a big lock for a long time to avoid concurrency issues */
-	mutex_lock(&queue->queuelock);
+	spin_lock_bh(&queue->queuelock);
 
 	/*
 	 * Can go on to queue if we have space in either:
@@ -814,15 +814,15 @@
 		ret = -EBUSY;
 		if ((skreq->base.flags & CRYPTO_TFM_REQ_MAY_BACKLOG)) {
 			list_add_tail(&sec_req->backlog_head, &ctx->backlog);
-			mutex_unlock(&queue->queuelock);
+			spin_unlock_bh(&queue->queuelock);
 			goto out;
 		}
 
-		mutex_unlock(&queue->queuelock);
+		spin_unlock_bh(&queue->queuelock);
 		goto err_free_elements;
 	}
 	ret = sec_send_request(sec_req, queue);
-	mutex_unlock(&queue->queuelock);
+	spin_unlock_bh(&queue->queuelock);
 	if (ret)
 		goto err_free_elements;
 
@@ -881,7 +881,7 @@
 	if (IS_ERR(ctx->queue))
 		return PTR_ERR(ctx->queue);
 
-	mutex_init(&ctx->queue->queuelock);
+	spin_lock_init(&ctx->queue->queuelock);
 	ctx->queue->havesoftqueue = false;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sec/sec_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sec/sec_drv.h
@@ -347,7 +347,7 @@
 	DECLARE_BITMAP(unprocessed, SEC_QUEUE_LEN);
 	DECLARE_KFIFO_PTR(softqueue, typeof(struct sec_request_el *));
 	bool havesoftqueue;
-	struct mutex queuelock;
+	spinlock_t queuelock;
 	void *shadow[SEC_QUEUE_LEN];
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sec2/sec.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sec2/sec.h
@@ -36,6 +36,7 @@
 	u8 *a_ivin;
 	dma_addr_t a_ivin_dma;
 	struct aead_request *aead_req;
+	bool fallback;
 };
 
 /* SEC request of Crypto */
@@ -89,9 +90,7 @@
 	dma_addr_t a_key_dma;
 	u8 *a_key;
 	u8 a_key_len;
-	u8 mac_len;
 	u8 a_alg;
-	bool fallback;
 	struct crypto_shash *hash_tfm;
 	struct crypto_aead *fallback_aead_tfm;
 };
@@ -119,7 +118,7 @@
 	struct idr req_idr;
 	struct sec_alg_res res[QM_Q_DEPTH];
 	struct sec_ctx *ctx;
-	struct mutex req_lock;
+	spinlock_t req_lock;
 	struct list_head backlog;
 	struct hisi_acc_sgl_pool *c_in_pool;
 	struct hisi_acc_sgl_pool *c_out_pool;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sec2/sec_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sec2/sec_crypto.c
@@ -55,7 +55,6 @@
 #define SEC_TYPE_MASK		0x0F
 #define SEC_DONE_MASK		0x0001
 #define SEC_ICV_MASK		0x000E
-#define SEC_SQE_LEN_RATE_MASK	0x3
 
 #define SEC_TOTAL_IV_SZ		(SEC_IV_SIZE * QM_Q_DEPTH)
 #define SEC_SGL_SGE_NR		128
@@ -77,16 +76,16 @@
 #define SEC_TOTAL_PBUF_SZ	(PAGE_SIZE * SEC_PBUF_PAGE_NUM +	\
 			SEC_PBUF_LEFT_SZ)
 
-#define SEC_SQE_LEN_RATE	4
 #define SEC_SQE_CFLAG		2
 #define SEC_SQE_AEAD_FLAG	3
 #define SEC_SQE_DONE		0x1
 #define SEC_ICV_ERR		0x2
-#define MIN_MAC_LEN		4
 #define MAC_LEN_MASK		0x1U
 #define MAX_INPUT_DATA_LEN	0xFFFE00
 #define BITS_MASK		0xFF
+#define WORD_MASK		0x3
 #define BYTE_BITS		0x8
+#define BYTES_TO_WORDS(bcount)	((bcount) >> 2)
 #define SEC_XTS_NAME_SZ		0x3
 #define IV_CM_CAL_NUM		2
 #define IV_CL_MASK		0x7
@@ -124,11 +123,11 @@
 {
 	int req_id;
 
-	mutex_lock(&qp_ctx->req_lock);
+	spin_lock_bh(&qp_ctx->req_lock);
 
 	req_id = idr_alloc_cyclic(&qp_ctx->req_idr, NULL,
 				  0, QM_Q_DEPTH, GFP_ATOMIC);
-	mutex_unlock(&qp_ctx->req_lock);
+	spin_unlock_bh(&qp_ctx->req_lock);
 	if (unlikely(req_id < 0)) {
 		dev_err(req->ctx->dev, "alloc req id fail!\n");
 		return req_id;
@@ -153,9 +152,9 @@
 	qp_ctx->req_list[req_id] = NULL;
 	req->qp_ctx = NULL;
 
-	mutex_lock(&qp_ctx->req_lock);
+	spin_lock_bh(&qp_ctx->req_lock);
 	idr_remove(&qp_ctx->req_idr, req_id);
-	mutex_unlock(&qp_ctx->req_lock);
+	spin_unlock_bh(&qp_ctx->req_lock);
 }
 
 static u8 pre_parse_finished_bd(struct bd_status *status, void *resp)
@@ -270,7 +269,7 @@
 	    !(req->flag & CRYPTO_TFM_REQ_MAY_BACKLOG))
 		return -EBUSY;
 
-	mutex_lock(&qp_ctx->req_lock);
+	spin_lock_bh(&qp_ctx->req_lock);
 	ret = hisi_qp_send(qp_ctx->qp, &req->sec_sqe);
 
 	if (ctx->fake_req_limit <=
@@ -278,10 +277,10 @@
 		list_add_tail(&req->backlog_head, &qp_ctx->backlog);
 		atomic64_inc(&ctx->sec->debug.dfx.send_cnt);
 		atomic64_inc(&ctx->sec->debug.dfx.send_busy_cnt);
-		mutex_unlock(&qp_ctx->req_lock);
+		spin_unlock_bh(&qp_ctx->req_lock);
 		return -EBUSY;
 	}
-	mutex_unlock(&qp_ctx->req_lock);
+	spin_unlock_bh(&qp_ctx->req_lock);
 
 	if (unlikely(ret == -EBUSY))
 		return -ENOBUFS;
@@ -463,8 +462,10 @@
 
 	if (ctx->pbuf_supported)
 		sec_free_pbuf_resource(dev, qp_ctx->res);
-	if (ctx->alg_type == SEC_AEAD)
+	if (ctx->alg_type == SEC_AEAD) {
 		sec_free_mac_resource(dev, qp_ctx->res);
+		sec_free_aiv_resource(dev, qp_ctx->res);
+	}
 }
 
 static int sec_create_qp_ctx(struct hisi_qm *qm, struct sec_ctx *ctx,
@@ -484,7 +485,7 @@
 
 	qp->req_cb = sec_req_cb;
 
-	mutex_init(&qp_ctx->req_lock);
+	spin_lock_init(&qp_ctx->req_lock);
 	idr_init(&qp_ctx->req_idr);
 	INIT_LIST_HEAD(&qp_ctx->backlog);
 
@@ -617,7 +618,7 @@
 {
 	struct sec_auth_ctx *a_ctx = &ctx->a_ctx;
 
-	a_ctx->a_key = dma_alloc_coherent(ctx->dev, SEC_MAX_KEY_SIZE,
+	a_ctx->a_key = dma_alloc_coherent(ctx->dev, SEC_MAX_AKEY_SIZE,
 					  &a_ctx->a_key_dma, GFP_KERNEL);
 	if (!a_ctx->a_key)
 		return -ENOMEM;
@@ -629,8 +630,8 @@
 {
 	struct sec_auth_ctx *a_ctx = &ctx->a_ctx;
 
-	memzero_explicit(a_ctx->a_key, SEC_MAX_KEY_SIZE);
-	dma_free_coherent(ctx->dev, SEC_MAX_KEY_SIZE,
+	memzero_explicit(a_ctx->a_key, SEC_MAX_AKEY_SIZE);
+	dma_free_coherent(ctx->dev, SEC_MAX_AKEY_SIZE,
 			  a_ctx->a_key, a_ctx->a_key_dma);
 }
 
@@ -641,13 +642,15 @@
 	struct sec_cipher_ctx *c_ctx = &ctx->c_ctx;
 
 	c_ctx->fallback = false;
+
+	/* Currently, only XTS mode need fallback tfm when using 192bit key */
 	if (likely(strncmp(alg, "xts", SEC_XTS_NAME_SZ)))
 		return 0;
 
 	c_ctx->fbtfm = crypto_alloc_sync_skcipher(alg, 0,
 						  CRYPTO_ALG_NEED_FALLBACK);
 	if (IS_ERR(c_ctx->fbtfm)) {
-		pr_err("failed to alloc fallback tfm!\n");
+		pr_err("failed to alloc xts mode fallback tfm!\n");
 		return PTR_ERR(c_ctx->fbtfm);
 	}
 
@@ -799,6 +802,7 @@
 		ret = sec_skcipher_aes_sm4_setkey(c_ctx, keylen, c_mode);
 		break;
 	default:
+		dev_err(dev, "sec c_alg err!\n");
 		return -EINVAL;
 	}
 
@@ -808,7 +812,7 @@
 	}
 
 	memcpy(c_ctx->c_key, key, keylen);
-	if (c_ctx->fallback) {
+	if (c_ctx->fallback && c_ctx->fbtfm) {
 		ret = crypto_sync_skcipher_setkey(c_ctx->fbtfm, key, keylen);
 		if (ret) {
 			dev_err(dev, "failed to set fallback skcipher key!\n");
@@ -902,15 +906,14 @@
 	struct aead_request *aead_req = req->aead_req;
 	struct crypto_aead *tfm = crypto_aead_reqtfm(aead_req);
 	size_t authsize = crypto_aead_authsize(tfm);
-	u8 *mac_out = req->out_mac;
 	struct scatterlist *sgl = aead_req->src;
+	u8 *mac_out = req->out_mac;
 	size_t copy_size;
 	off_t skip_size;
 
 	/* Copy input mac */
 	skip_size = aead_req->assoclen + aead_req->cryptlen - authsize;
-	copy_size = sg_pcopy_to_buffer(sgl, sg_nents(sgl), mac_out,
-				       authsize, skip_size);
+	copy_size = sg_pcopy_to_buffer(sgl, sg_nents(sgl), mac_out, authsize, skip_size);
 	if (unlikely(copy_size != authsize))
 		return -EINVAL;
 
@@ -1044,11 +1047,6 @@
 	struct crypto_shash *hash_tfm = ctx->hash_tfm;
 	int blocksize, digestsize, ret;
 
-	if (!keys->authkeylen) {
-		pr_err("hisi_sec2: aead auth key error!\n");
-		return -EINVAL;
-	}
-
 	blocksize = crypto_shash_blocksize(hash_tfm);
 	digestsize = crypto_shash_digestsize(hash_tfm);
 	if (keys->authkeylen > blocksize) {
@@ -1060,7 +1058,8 @@
 		}
 		ctx->a_key_len = digestsize;
 	} else {
-		memcpy(ctx->a_key, keys->authkey, keys->authkeylen);
+		if (keys->authkeylen)
+			memcpy(ctx->a_key, keys->authkey, keys->authkeylen);
 		ctx->a_key_len = keys->authkeylen;
 	}
 
@@ -1073,10 +1072,7 @@
 	struct sec_ctx *ctx = crypto_tfm_ctx(tfm);
 	struct sec_auth_ctx *a_ctx = &ctx->a_ctx;
 
-	if (unlikely(a_ctx->fallback_aead_tfm))
-		return crypto_aead_setauthsize(a_ctx->fallback_aead_tfm, authsize);
-
-	return 0;
+	return crypto_aead_setauthsize(a_ctx->fallback_aead_tfm, authsize);
 }
 
 static int sec_aead_fallback_setkey(struct sec_auth_ctx *a_ctx,
@@ -1092,7 +1088,6 @@
 static int sec_aead_setkey(struct crypto_aead *tfm, const u8 *key,
 			   const u32 keylen, const enum sec_hash_alg a_alg,
 			   const enum sec_calg c_alg,
-			   const enum sec_mac_len mac_len,
 			   const enum sec_cmode c_mode)
 {
 	struct sec_ctx *ctx = crypto_aead_ctx(tfm);
@@ -1104,7 +1099,6 @@
 
 	ctx->a_ctx.a_alg = a_alg;
 	ctx->c_ctx.c_alg = c_alg;
-	ctx->a_ctx.mac_len = mac_len;
 	c_ctx->c_mode = c_mode;
 
 	if (c_mode == SEC_CMODE_CCM || c_mode == SEC_CMODE_GCM) {
@@ -1115,16 +1109,11 @@
 		}
 		memcpy(c_ctx->c_key, key, keylen);
 
-		if (unlikely(a_ctx->fallback_aead_tfm)) {
-			ret = sec_aead_fallback_setkey(a_ctx, tfm, key, keylen);
-			if (ret)
-				return ret;
-		}
-
-		return 0;
+		return sec_aead_fallback_setkey(a_ctx, tfm, key, keylen);
 	}
 
-	if (crypto_authenc_extractkeys(&keys, key, keylen))
+	ret = crypto_authenc_extractkeys(&keys, key, keylen);
+	if (ret)
 		goto bad_key;
 
 	ret = sec_aead_aes_set_key(c_ctx, &keys);
@@ -1139,9 +1128,15 @@
 		goto bad_key;
 	}
 
-	if ((ctx->a_ctx.mac_len & SEC_SQE_LEN_RATE_MASK)  ||
-	    (ctx->a_ctx.a_key_len & SEC_SQE_LEN_RATE_MASK)) {
-		dev_err(dev, "MAC or AUTH key length error!\n");
+	if (ctx->a_ctx.a_key_len & WORD_MASK) {
+		ret = -EINVAL;
+		dev_err(dev, "AUTH key length error!\n");
+		goto bad_key;
+	}
+
+	ret = sec_aead_fallback_setkey(a_ctx, tfm, key, keylen);
+	if (ret) {
+		dev_err(dev, "set sec fallback key err!\n");
 		goto bad_key;
 	}
 
@@ -1149,31 +1144,23 @@
 
 bad_key:
 	memzero_explicit(&keys, sizeof(struct crypto_authenc_keys));
-	return -EINVAL;
+	return ret;
 }
 
 
-#define GEN_SEC_AEAD_SETKEY_FUNC(name, aalg, calg, maclen, cmode)	\
-static int sec_setkey_##name(struct crypto_aead *tfm, const u8 *key,	\
-	u32 keylen)							\
-{									\
-	return sec_aead_setkey(tfm, key, keylen, aalg, calg, maclen, cmode);\
+#define GEN_SEC_AEAD_SETKEY_FUNC(name, aalg, calg, cmode)				\
+static int sec_setkey_##name(struct crypto_aead *tfm, const u8 *key, u32 keylen)	\
+{											\
+	return sec_aead_setkey(tfm, key, keylen, aalg, calg, cmode);			\
 }
 
-GEN_SEC_AEAD_SETKEY_FUNC(aes_cbc_sha1, SEC_A_HMAC_SHA1,
-			 SEC_CALG_AES, SEC_HMAC_SHA1_MAC, SEC_CMODE_CBC)
-GEN_SEC_AEAD_SETKEY_FUNC(aes_cbc_sha256, SEC_A_HMAC_SHA256,
-			 SEC_CALG_AES, SEC_HMAC_SHA256_MAC, SEC_CMODE_CBC)
-GEN_SEC_AEAD_SETKEY_FUNC(aes_cbc_sha512, SEC_A_HMAC_SHA512,
-			 SEC_CALG_AES, SEC_HMAC_SHA512_MAC, SEC_CMODE_CBC)
-GEN_SEC_AEAD_SETKEY_FUNC(aes_ccm, 0, SEC_CALG_AES,
-			 SEC_HMAC_CCM_MAC, SEC_CMODE_CCM)
-GEN_SEC_AEAD_SETKEY_FUNC(aes_gcm, 0, SEC_CALG_AES,
-			 SEC_HMAC_GCM_MAC, SEC_CMODE_GCM)
-GEN_SEC_AEAD_SETKEY_FUNC(sm4_ccm, 0, SEC_CALG_SM4,
-			 SEC_HMAC_CCM_MAC, SEC_CMODE_CCM)
-GEN_SEC_AEAD_SETKEY_FUNC(sm4_gcm, 0, SEC_CALG_SM4,
-			 SEC_HMAC_GCM_MAC, SEC_CMODE_GCM)
+GEN_SEC_AEAD_SETKEY_FUNC(aes_cbc_sha1, SEC_A_HMAC_SHA1, SEC_CALG_AES, SEC_CMODE_CBC)
+GEN_SEC_AEAD_SETKEY_FUNC(aes_cbc_sha256, SEC_A_HMAC_SHA256, SEC_CALG_AES, SEC_CMODE_CBC)
+GEN_SEC_AEAD_SETKEY_FUNC(aes_cbc_sha512, SEC_A_HMAC_SHA512, SEC_CALG_AES, SEC_CMODE_CBC)
+GEN_SEC_AEAD_SETKEY_FUNC(aes_ccm, 0, SEC_CALG_AES, SEC_CMODE_CCM)
+GEN_SEC_AEAD_SETKEY_FUNC(aes_gcm, 0, SEC_CALG_AES, SEC_CMODE_GCM)
+GEN_SEC_AEAD_SETKEY_FUNC(sm4_ccm, 0, SEC_CALG_SM4, SEC_CMODE_CCM)
+GEN_SEC_AEAD_SETKEY_FUNC(sm4_gcm, 0, SEC_CALG_SM4, SEC_CMODE_GCM)
 
 static int sec_aead_sgl_map(struct sec_ctx *ctx, struct sec_req *req)
 {
@@ -1373,7 +1360,7 @@
 {
 	struct sec_req *backlog_req = NULL;
 
-	mutex_lock(&qp_ctx->req_lock);
+	spin_lock_bh(&qp_ctx->req_lock);
 	if (ctx->fake_req_limit >=
 	    atomic_read(&qp_ctx->qp->qp_status.used) &&
 	    !list_empty(&qp_ctx->backlog)) {
@@ -1381,7 +1368,7 @@
 				typeof(*backlog_req), backlog_head);
 		list_del(&backlog_req->backlog_head);
 	}
-	mutex_unlock(&qp_ctx->req_lock);
+	spin_unlock_bh(&qp_ctx->req_lock);
 
 	return backlog_req;
 }
@@ -1418,9 +1405,10 @@
 static void set_aead_auth_iv(struct sec_ctx *ctx, struct sec_req *req)
 {
 	struct aead_request *aead_req = req->aead_req.aead_req;
-	struct sec_cipher_req *c_req = &req->c_req;
+	struct crypto_aead *tfm = crypto_aead_reqtfm(aead_req);
+	size_t authsize = crypto_aead_authsize(tfm);
 	struct sec_aead_req *a_req = &req->aead_req;
-	size_t authsize = ctx->a_ctx.mac_len;
+	struct sec_cipher_req *c_req = &req->c_req;
 	u32 data_size = aead_req->cryptlen;
 	u8 flage = 0;
 	u8 cm, cl;
@@ -1461,10 +1449,8 @@
 static void sec_aead_set_iv(struct sec_ctx *ctx, struct sec_req *req)
 {
 	struct aead_request *aead_req = req->aead_req.aead_req;
-	struct crypto_aead *tfm = crypto_aead_reqtfm(aead_req);
-	size_t authsize = crypto_aead_authsize(tfm);
-	struct sec_cipher_req *c_req = &req->c_req;
 	struct sec_aead_req *a_req = &req->aead_req;
+	struct sec_cipher_req *c_req = &req->c_req;
 
 	memcpy(c_req->c_ivin, aead_req->iv, ctx->c_ctx.ivsize);
 
@@ -1472,15 +1458,11 @@
 		/*
 		 * CCM 16Byte Cipher_IV: {1B_Flage,13B_IV,2B_counter},
 		 * the  counter must set to 0x01
+		 * CCM 16Byte Auth_IV: {1B_AFlage,13B_IV,2B_Ptext_length}
 		 */
-		ctx->a_ctx.mac_len = authsize;
-		/* CCM 16Byte Auth_IV: {1B_AFlage,13B_IV,2B_Ptext_length} */
 		set_aead_auth_iv(ctx, req);
-	}
-
-	/* GCM 12Byte Cipher_IV == Auth_IV */
-	if (ctx->c_ctx.c_mode == SEC_CMODE_GCM) {
-		ctx->a_ctx.mac_len = authsize;
+	} else if (ctx->c_ctx.c_mode == SEC_CMODE_GCM) {
+		/* GCM 12Byte Cipher_IV == Auth_IV */
 		memcpy(a_req->a_ivin, c_req->c_ivin, SEC_AIV_SIZE);
 	}
 }
@@ -1490,9 +1472,11 @@
 {
 	struct sec_aead_req *a_req = &req->aead_req;
 	struct aead_request *aq = a_req->aead_req;
+	struct crypto_aead *tfm = crypto_aead_reqtfm(aq);
+	size_t authsize = crypto_aead_authsize(tfm);
 
 	/* C_ICV_Len is MAC size, 0x4 ~ 0x10 */
-	sec_sqe->type2.icvw_kmode |= cpu_to_le16((u16)ctx->mac_len);
+	sec_sqe->type2.icvw_kmode |= cpu_to_le16((u16)authsize);
 
 	/* mode set to CCM/GCM, don't set {A_Alg, AKey_Len, MAC_Len} */
 	sec_sqe->type2.a_key_addr = sec_sqe->type2.c_key_addr;
@@ -1516,9 +1500,11 @@
 {
 	struct sec_aead_req *a_req = &req->aead_req;
 	struct aead_request *aq = a_req->aead_req;
+	struct crypto_aead *tfm = crypto_aead_reqtfm(aq);
+	size_t authsize = crypto_aead_authsize(tfm);
 
 	/* C_ICV_Len is MAC size, 0x4 ~ 0x10 */
-	sqe3->c_icv_key |= cpu_to_le16((u16)ctx->mac_len << SEC_MAC_OFFSET_V3);
+	sqe3->c_icv_key |= cpu_to_le16((u16)authsize << SEC_MAC_OFFSET_V3);
 
 	/* mode set to CCM/GCM, don't set {A_Alg, AKey_Len, MAC_Len} */
 	sqe3->a_key_addr = sqe3->c_key_addr;
@@ -1542,15 +1528,15 @@
 	struct sec_aead_req *a_req = &req->aead_req;
 	struct sec_cipher_req *c_req = &req->c_req;
 	struct aead_request *aq = a_req->aead_req;
+	struct crypto_aead *tfm = crypto_aead_reqtfm(aq);
+	size_t authsize = crypto_aead_authsize(tfm);
 
 	sec_sqe->type2.a_key_addr = cpu_to_le64(ctx->a_key_dma);
 
-	sec_sqe->type2.mac_key_alg =
-			cpu_to_le32(ctx->mac_len / SEC_SQE_LEN_RATE);
+	sec_sqe->type2.mac_key_alg = cpu_to_le32(BYTES_TO_WORDS(authsize));
 
 	sec_sqe->type2.mac_key_alg |=
-			cpu_to_le32((u32)((ctx->a_key_len) /
-			SEC_SQE_LEN_RATE) << SEC_AKEY_OFFSET);
+			cpu_to_le32((u32)BYTES_TO_WORDS(ctx->a_key_len) << SEC_AKEY_OFFSET);
 
 	sec_sqe->type2.mac_key_alg |=
 			cpu_to_le32((u32)(ctx->a_alg) << SEC_AEAD_ALG_OFFSET);
@@ -1596,16 +1582,16 @@
 	struct sec_aead_req *a_req = &req->aead_req;
 	struct sec_cipher_req *c_req = &req->c_req;
 	struct aead_request *aq = a_req->aead_req;
+	struct crypto_aead *tfm = crypto_aead_reqtfm(aq);
+	size_t authsize = crypto_aead_authsize(tfm);
 
 	sqe3->a_key_addr = cpu_to_le64(ctx->a_key_dma);
 
 	sqe3->auth_mac_key |=
-			cpu_to_le32((u32)(ctx->mac_len /
-			SEC_SQE_LEN_RATE) << SEC_MAC_OFFSET_V3);
+			cpu_to_le32(BYTES_TO_WORDS(authsize) << SEC_MAC_OFFSET_V3);
 
 	sqe3->auth_mac_key |=
-			cpu_to_le32((u32)(ctx->a_key_len /
-			SEC_SQE_LEN_RATE) << SEC_AKEY_OFFSET_V3);
+			cpu_to_le32((u32)BYTES_TO_WORDS(ctx->a_key_len) << SEC_AKEY_OFFSET_V3);
 
 	sqe3->auth_mac_key |=
 			cpu_to_le32((u32)(ctx->a_alg) << SEC_AUTH_ALG_OFFSET_V3);
@@ -1651,9 +1637,9 @@
 {
 	struct aead_request *a_req = req->aead_req.aead_req;
 	struct crypto_aead *tfm = crypto_aead_reqtfm(a_req);
+	size_t authsize = crypto_aead_authsize(tfm);
 	struct sec_aead_req *aead_req = &req->aead_req;
 	struct sec_cipher_req *c_req = &req->c_req;
-	size_t authsize = crypto_aead_authsize(tfm);
 	struct sec_qp_ctx *qp_ctx = req->qp_ctx;
 	struct aead_request *backlog_aead_req;
 	struct sec_req *backlog_req;
@@ -1666,11 +1652,8 @@
 	if (!err && c_req->encrypt) {
 		struct scatterlist *sgl = a_req->dst;
 
-		sz = sg_pcopy_from_buffer(sgl, sg_nents(sgl),
-					  aead_req->out_mac,
-					  authsize, a_req->cryptlen +
-					  a_req->assoclen);
-
+		sz = sg_pcopy_from_buffer(sgl, sg_nents(sgl), aead_req->out_mac,
+					  authsize, a_req->cryptlen + a_req->assoclen);
 		if (unlikely(sz != authsize)) {
 			dev_err(c->dev, "copy out mac err!\n");
 			err = -EINVAL;
@@ -1879,8 +1862,10 @@
 
 static int sec_aead_ctx_init(struct crypto_aead *tfm, const char *hash_name)
 {
+	struct aead_alg *alg = crypto_aead_alg(tfm);
 	struct sec_ctx *ctx = crypto_aead_ctx(tfm);
-	struct sec_auth_ctx *auth_ctx = &ctx->a_ctx;
+	struct sec_auth_ctx *a_ctx = &ctx->a_ctx;
+	const char *aead_name = alg->base.cra_name;
 	int ret;
 
 	ret = sec_aead_init(tfm);
@@ -1889,11 +1874,20 @@
 		return ret;
 	}
 
-	auth_ctx->hash_tfm = crypto_alloc_shash(hash_name, 0, 0);
-	if (IS_ERR(auth_ctx->hash_tfm)) {
+	a_ctx->hash_tfm = crypto_alloc_shash(hash_name, 0, 0);
+	if (IS_ERR(a_ctx->hash_tfm)) {
 		dev_err(ctx->dev, "aead alloc shash error!\n");
 		sec_aead_exit(tfm);
-		return PTR_ERR(auth_ctx->hash_tfm);
+		return PTR_ERR(a_ctx->hash_tfm);
+	}
+
+	a_ctx->fallback_aead_tfm = crypto_alloc_aead(aead_name, 0,
+						     CRYPTO_ALG_NEED_FALLBACK | CRYPTO_ALG_ASYNC);
+	if (IS_ERR(a_ctx->fallback_aead_tfm)) {
+		dev_err(ctx->dev, "aead driver alloc fallback tfm error!\n");
+		crypto_free_shash(ctx->a_ctx.hash_tfm);
+		sec_aead_exit(tfm);
+		return PTR_ERR(a_ctx->fallback_aead_tfm);
 	}
 
 	return 0;
@@ -1903,6 +1897,7 @@
 {
 	struct sec_ctx *ctx = crypto_aead_ctx(tfm);
 
+	crypto_free_aead(ctx->a_ctx.fallback_aead_tfm);
 	crypto_free_shash(ctx->a_ctx.hash_tfm);
 	sec_aead_exit(tfm);
 }
@@ -1929,7 +1924,6 @@
 		sec_aead_exit(tfm);
 		return PTR_ERR(a_ctx->fallback_aead_tfm);
 	}
-	a_ctx->fallback = false;
 
 	return 0;
 }
@@ -1957,7 +1951,6 @@
 	return sec_aead_ctx_init(tfm, "sha512");
 }
 
-
 static int sec_skcipher_cryptlen_ckeck(struct sec_ctx *ctx,
 	struct sec_req *sreq)
 {
@@ -2032,13 +2025,12 @@
 				    struct skcipher_request *sreq, bool encrypt)
 {
 	struct sec_cipher_ctx *c_ctx = &ctx->c_ctx;
+	SYNC_SKCIPHER_REQUEST_ON_STACK(subreq, c_ctx->fbtfm);
 	struct device *dev = ctx->dev;
 	int ret;
 
-	SYNC_SKCIPHER_REQUEST_ON_STACK(subreq, c_ctx->fbtfm);
-
 	if (!c_ctx->fbtfm) {
-		dev_err(dev, "failed to check fallback tfm\n");
+		dev_err_ratelimited(dev, "the soft tfm isn't supported in the current system.\n");
 		return -EINVAL;
 	}
 
@@ -2200,21 +2192,20 @@
 {
 	struct aead_request *req = sreq->aead_req.aead_req;
 	struct crypto_aead *tfm = crypto_aead_reqtfm(req);
-	size_t authsize = crypto_aead_authsize(tfm);
+	size_t sz = crypto_aead_authsize(tfm);
 	u8 c_mode = ctx->c_ctx.c_mode;
 	struct device *dev = ctx->dev;
 	int ret;
 
-	if (unlikely(req->cryptlen + req->assoclen > MAX_INPUT_DATA_LEN ||
-	    req->assoclen > SEC_MAX_AAD_LEN)) {
-		dev_err(dev, "aead input spec error!\n");
+	/* Hardware does not handle cases where authsize is not 4 bytes aligned */
+	if (c_mode == SEC_CMODE_CBC && (sz & WORD_MASK)) {
+		sreq->aead_req.fallback = true;
 		return -EINVAL;
 	}
 
-	if (unlikely((c_mode == SEC_CMODE_GCM && authsize < DES_BLOCK_SIZE) ||
-	   (c_mode == SEC_CMODE_CCM && (authsize < MIN_MAC_LEN ||
-		authsize & MAC_LEN_MASK)))) {
-		dev_err(dev, "aead input mac length error!\n");
+	if (unlikely(req->cryptlen + req->assoclen > MAX_INPUT_DATA_LEN ||
+	    req->assoclen > SEC_MAX_AAD_LEN)) {
+		dev_err(dev, "aead input spec error!\n");
 		return -EINVAL;
 	}
 
@@ -2229,7 +2220,7 @@
 	if (sreq->c_req.encrypt)
 		sreq->c_req.c_len = req->cryptlen;
 	else
-		sreq->c_req.c_len = req->cryptlen - authsize;
+		sreq->c_req.c_len = req->cryptlen - sz;
 	if (c_mode == SEC_CMODE_CBC) {
 		if (unlikely(sreq->c_req.c_len & (AES_BLOCK_SIZE - 1))) {
 			dev_err(dev, "aead crypto length error!\n");
@@ -2255,9 +2246,8 @@
 
 	if (ctx->sec->qm.ver == QM_HW_V2) {
 		if (unlikely(!req->cryptlen || (!sreq->c_req.encrypt &&
-		    req->cryptlen <= authsize))) {
-			dev_err(dev, "Kunpeng920 not support 0 length!\n");
-			ctx->a_ctx.fallback = true;
+			     req->cryptlen <= authsize))) {
+			sreq->aead_req.fallback = true;
 			return -EINVAL;
 		}
 	}
@@ -2284,15 +2274,13 @@
 				struct aead_request *aead_req,
 				bool encrypt)
 {
-	struct aead_request *subreq = aead_request_ctx(aead_req);
 	struct sec_auth_ctx *a_ctx = &ctx->a_ctx;
-	struct device *dev = ctx->dev;
+	struct aead_request *subreq;
+	int ret;
 
-	/* Kunpeng920 aead mode not support input 0 size */
-	if (!a_ctx->fallback_aead_tfm) {
-		dev_err(dev, "aead fallback tfm is NULL!\n");
-		return -EINVAL;
-	}
+	subreq = aead_request_alloc(a_ctx->fallback_aead_tfm, GFP_KERNEL);
+	if (!subreq)
+		return -ENOMEM;
 
 	aead_request_set_tfm(subreq, a_ctx->fallback_aead_tfm);
 	aead_request_set_callback(subreq, aead_req->base.flags,
@@ -2301,8 +2289,13 @@
 			       aead_req->cryptlen, aead_req->iv);
 	aead_request_set_ad(subreq, aead_req->assoclen);
 
-	return encrypt ? crypto_aead_encrypt(subreq) :
-		   crypto_aead_decrypt(subreq);
+	if (encrypt)
+		ret = crypto_aead_encrypt(subreq);
+	else
+		ret = crypto_aead_decrypt(subreq);
+	aead_request_free(subreq);
+
+	return ret;
 }
 
 static int sec_aead_crypto(struct aead_request *a_req, bool encrypt)
@@ -2316,10 +2309,11 @@
 	req->aead_req.aead_req = a_req;
 	req->c_req.encrypt = encrypt;
 	req->ctx = ctx;
+	req->aead_req.fallback = false;
 
 	ret = sec_aead_param_check(ctx, req);
 	if (unlikely(ret)) {
-		if (ctx->a_ctx.fallback)
+		if (req->aead_req.fallback)
 			return sec_aead_soft_crypto(ctx, a_req, encrypt);
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sec2/sec_crypto.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sec2/sec_crypto.h
@@ -7,6 +7,7 @@
 #define SEC_AIV_SIZE		12
 #define SEC_IV_SIZE		24
 #define SEC_MAX_KEY_SIZE	64
+#define SEC_MAX_AKEY_SIZE	128
 #define SEC_COMM_SCENE		0
 #define SEC_MIN_BLOCK_SZ	1
 
@@ -22,17 +23,6 @@
 	SEC_A_HMAC_SHA512 = 0x15,
 };
 
-enum sec_mac_len {
-	SEC_HMAC_CCM_MAC   = 16,
-	SEC_HMAC_GCM_MAC   = 16,
-	SEC_SM3_MAC        = 32,
-	SEC_HMAC_SM3_MAC   = 32,
-	SEC_HMAC_MD5_MAC   = 16,
-	SEC_HMAC_SHA1_MAC   = 20,
-	SEC_HMAC_SHA256_MAC = 32,
-	SEC_HMAC_SHA512_MAC = 64,
-};
-
 enum sec_cmode {
 	SEC_CMODE_ECB    = 0x0,
 	SEC_CMODE_CBC    = 0x1,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sec2/sec_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sec2/sec_main.c
@@ -443,9 +443,11 @@
 
 	writel(SEC_SAA_ENABLE, qm->io_base + SEC_SAA_EN_REG);
 
-	/* Enable sm4 extra mode, as ctr/ecb */
-	writel_relaxed(SEC_BD_ERR_CHK_EN0,
-		       qm->io_base + SEC_BD_ERR_CHK_EN_REG0);
+	/* HW V2 enable sm4 extra mode, as ctr/ecb */
+	if (qm->ver < QM_HW_V3)
+		writel_relaxed(SEC_BD_ERR_CHK_EN0,
+			       qm->io_base + SEC_BD_ERR_CHK_EN_REG0);
+
 	/* Enable sm4 xts mode multiple iv */
 	writel_relaxed(SEC_BD_ERR_CHK_EN1,
 		       qm->io_base + SEC_BD_ERR_CHK_EN_REG1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/sgl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/sgl.c
@@ -122,9 +122,8 @@
 	for (j = 0; j < i; j++) {
 		dma_free_coherent(dev, block_size, block[j].sgl,
 				  block[j].sgl_dma);
-		memset(block + j, 0, sizeof(*block));
 	}
-	kfree(pool);
+	kfree_sensitive(pool);
 	return ERR_PTR(-ENOMEM);
 }
 EXPORT_SYMBOL_GPL(hisi_acc_create_sgl_pool);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/hisilicon/zip/zip_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/hisilicon/zip/zip_crypto.c
@@ -122,12 +122,12 @@
 	if (ret || n == 0 || n > HISI_ACC_SGL_SGE_NR_MAX)
 		return -EINVAL;
 
-	return param_set_int(val, kp);
+	return param_set_ushort(val, kp);
 }
 
 static const struct kernel_param_ops sgl_sge_nr_ops = {
 	.set = sgl_sge_nr_set,
-	.get = param_get_int,
+	.get = param_get_ushort,
 };
 
 static u16 sgl_sge_nr = HZIP_SGL_SGE_NR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/img-hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/img-hash.c
@@ -358,12 +358,16 @@
 static void img_hash_dma_task(unsigned long d)
 {
 	struct img_hash_dev *hdev = (struct img_hash_dev *)d;
-	struct img_hash_request_ctx *ctx = ahash_request_ctx(hdev->req);
+	struct img_hash_request_ctx *ctx;
 	u8 *addr;
 	size_t nbytes, bleft, wsend, len, tbc;
 	struct scatterlist tsg;
 
-	if (!hdev->req || !ctx->sg)
+	if (!hdev->req)
+		return;
+
+	ctx = ahash_request_ctx(hdev->req);
+	if (!ctx->sg)
 		return;
 
 	addr = sg_virt(ctx->sg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/inside-secure/safexcel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/inside-secure/safexcel.c
@@ -1631,19 +1631,23 @@
 						     &priv->ring[i].rdr);
 		if (ret) {
 			dev_err(dev, "Failed to initialize rings\n");
-			return ret;
+			goto err_cleanup_rings;
 		}
 
 		priv->ring[i].rdr_req = devm_kcalloc(dev,
 			EIP197_DEFAULT_RING_SIZE,
 			sizeof(*priv->ring[i].rdr_req),
 			GFP_KERNEL);
-		if (!priv->ring[i].rdr_req)
-			return -ENOMEM;
+		if (!priv->ring[i].rdr_req) {
+			ret = -ENOMEM;
+			goto err_cleanup_rings;
+		}
 
 		ring_irq = devm_kzalloc(dev, sizeof(*ring_irq), GFP_KERNEL);
-		if (!ring_irq)
-			return -ENOMEM;
+		if (!ring_irq) {
+			ret = -ENOMEM;
+			goto err_cleanup_rings;
+		}
 
 		ring_irq->priv = priv;
 		ring_irq->ring = i;
@@ -1657,7 +1661,8 @@
 						ring_irq);
 		if (irq < 0) {
 			dev_err(dev, "Failed to get IRQ ID for ring %d\n", i);
-			return irq;
+			ret = irq;
+			goto err_cleanup_rings;
 		}
 
 		priv->ring[i].irq = irq;
@@ -1669,8 +1674,10 @@
 		snprintf(wq_name, 9, "wq_ring%d", i);
 		priv->ring[i].workqueue =
 			create_singlethread_workqueue(wq_name);
-		if (!priv->ring[i].workqueue)
-			return -ENOMEM;
+		if (!priv->ring[i].workqueue) {
+			ret = -ENOMEM;
+			goto err_cleanup_rings;
+		}
 
 		priv->ring[i].requests = 0;
 		priv->ring[i].busy = false;
@@ -1687,16 +1694,26 @@
 	ret = safexcel_hw_init(priv);
 	if (ret) {
 		dev_err(dev, "HW init failed (%d)\n", ret);
-		return ret;
+		goto err_cleanup_rings;
 	}
 
 	ret = safexcel_register_algorithms(priv);
 	if (ret) {
 		dev_err(dev, "Failed to register algorithms (%d)\n", ret);
-		return ret;
+		goto err_cleanup_rings;
 	}
 
 	return 0;
+
+err_cleanup_rings:
+	for (i = 0; i < priv->config.rings; i++) {
+		if (priv->ring[i].irq)
+			irq_set_affinity_hint(priv->ring[i].irq, NULL);
+		if (priv->ring[i].workqueue)
+			destroy_workqueue(priv->ring[i].workqueue);
+	}
+
+	return ret;
 }
 
 static void safexcel_hw_reset_rings(struct safexcel_crypto_priv *priv)
@@ -1831,6 +1848,8 @@
 	{},
 };
 
+MODULE_DEVICE_TABLE(of, safexcel_of_match_table);
+
 static struct platform_driver  crypto_safexcel = {
 	.probe		= safexcel_probe,
 	.remove		= safexcel_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/inside-secure/safexcel_hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/inside-secure/safexcel_hash.c
@@ -383,7 +383,7 @@
 					u32 x;
 
 					x = ipad[i] ^ ipad[i + 4];
-					cache[i] ^= swab(x);
+					cache[i] ^= swab32(x);
 				}
 			}
 			cache_len = AES_BLOCK_SIZE;
@@ -821,7 +821,7 @@
 			u32 *result = (void *)areq->result;
 
 			/* K3 */
-			result[i] = swab(ctx->base.ipad.word[i + 4]);
+			result[i] = swab32(ctx->base.ipad.word[i + 4]);
 		}
 		areq->result[0] ^= 0x80;			// 10- padding
 		crypto_cipher_encrypt_one(ctx->kaes, areq->result, areq->result);
@@ -2106,7 +2106,7 @@
 	crypto_cipher_encrypt_one(ctx->kaes, (u8 *)key_tmp + AES_BLOCK_SIZE,
 		"\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3");
 	for (i = 0; i < 3 * AES_BLOCK_SIZE / sizeof(u32); i++)
-		ctx->base.ipad.word[i] = swab(key_tmp[i]);
+		ctx->base.ipad.word[i] = swab32(key_tmp[i]);
 
 	crypto_cipher_clear_flags(ctx->kaes, CRYPTO_TFM_REQ_MASK);
 	crypto_cipher_set_flags(ctx->kaes, crypto_ahash_get_flags(tfm) &
@@ -2189,7 +2189,7 @@
 		return ret;
 
 	for (i = 0; i < len / sizeof(u32); i++)
-		ctx->base.ipad.word[i + 8] = swab(aes.key_enc[i]);
+		ctx->base.ipad.word[i + 8] = swab32(aes.key_enc[i]);
 
 	/* precompute the CMAC key material */
 	crypto_cipher_clear_flags(ctx->kaes, CRYPTO_TFM_REQ_MASK);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/ixp4xx_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/ixp4xx_crypto.c
@@ -470,6 +470,7 @@
 			return -ENODEV;
 		}
 		npe_id = npe_spec.args[0];
+		of_node_put(npe_spec.np);
 
 		ret = of_parse_phandle_with_fixed_args(np, "queue-rx", 1, 0,
 						       &queue_spec);
@@ -478,6 +479,7 @@
 			return -ENODEV;
 		}
 		recv_qid = queue_spec.args[0];
+		of_node_put(queue_spec.np);
 
 		ret = of_parse_phandle_with_fixed_args(np, "queue-txready", 1, 0,
 						       &queue_spec);
@@ -486,6 +488,7 @@
 			return -ENODEV;
 		}
 		send_qid = queue_spec.args[0];
+		of_node_put(queue_spec.np);
 	} else {
 		/*
 		 * Hardcoded engine when using platform data, this goes away
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/cesa/cipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/cesa/cipher.c
@@ -297,7 +297,7 @@
 static int mv_cesa_des3_ede_setkey(struct crypto_skcipher *cipher,
 				   const u8 *key, unsigned int len)
 {
-	struct mv_cesa_des_ctx *ctx = crypto_skcipher_ctx(cipher);
+	struct mv_cesa_des3_ctx *ctx = crypto_skcipher_ctx(cipher);
 	int err;
 
 	err = verify_skcipher_des3_key(cipher, key);
@@ -624,7 +624,6 @@
 	.decrypt = mv_cesa_ecb_des3_ede_decrypt,
 	.min_keysize = DES3_EDE_KEY_SIZE,
 	.max_keysize = DES3_EDE_KEY_SIZE,
-	.ivsize = DES3_EDE_BLOCK_SIZE,
 	.base = {
 		.cra_name = "ecb(des3_ede)",
 		.cra_driver_name = "mv-ecb-des3-ede",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/cesa/hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/cesa/hash.c
@@ -947,7 +947,7 @@
 		.base = {
 			.cra_name = "md5",
 			.cra_driver_name = "mv-md5",
-			.cra_priority = 300,
+			.cra_priority = 0,
 			.cra_flags = CRYPTO_ALG_ASYNC |
 				     CRYPTO_ALG_ALLOCATES_MEMORY |
 				     CRYPTO_ALG_KERN_DRIVER_ONLY,
@@ -1018,7 +1018,7 @@
 		.base = {
 			.cra_name = "sha1",
 			.cra_driver_name = "mv-sha1",
-			.cra_priority = 300,
+			.cra_priority = 0,
 			.cra_flags = CRYPTO_ALG_ASYNC |
 				     CRYPTO_ALG_ALLOCATES_MEMORY |
 				     CRYPTO_ALG_KERN_DRIVER_ONLY,
@@ -1092,7 +1092,7 @@
 		.base = {
 			.cra_name = "sha256",
 			.cra_driver_name = "mv-sha256",
-			.cra_priority = 300,
+			.cra_priority = 0,
 			.cra_flags = CRYPTO_ALG_ASYNC |
 				     CRYPTO_ALG_ALLOCATES_MEMORY |
 				     CRYPTO_ALG_KERN_DRIVER_ONLY,
@@ -1327,7 +1327,7 @@
 		.base = {
 			.cra_name = "hmac(md5)",
 			.cra_driver_name = "mv-hmac-md5",
-			.cra_priority = 300,
+			.cra_priority = 0,
 			.cra_flags = CRYPTO_ALG_ASYNC |
 				     CRYPTO_ALG_ALLOCATES_MEMORY |
 				     CRYPTO_ALG_KERN_DRIVER_ONLY,
@@ -1398,7 +1398,7 @@
 		.base = {
 			.cra_name = "hmac(sha1)",
 			.cra_driver_name = "mv-hmac-sha1",
-			.cra_priority = 300,
+			.cra_priority = 0,
 			.cra_flags = CRYPTO_ALG_ASYNC |
 				     CRYPTO_ALG_ALLOCATES_MEMORY |
 				     CRYPTO_ALG_KERN_DRIVER_ONLY,
@@ -1469,7 +1469,7 @@
 		.base = {
 			.cra_name = "hmac(sha256)",
 			.cra_driver_name = "mv-hmac-sha256",
-			.cra_priority = 300,
+			.cra_priority = 0,
 			.cra_flags = CRYPTO_ALG_ASYNC |
 				     CRYPTO_ALG_ALLOCATES_MEMORY |
 				     CRYPTO_ALG_KERN_DRIVER_ONLY,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/octeontx/otx_cptpf_ucode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/octeontx/otx_cptpf_ucode.c
@@ -286,6 +286,7 @@
 	struct tar_ucode_info_t *tar_info;
 	struct otx_cpt_ucode_hdr *ucode_hdr;
 	int ucode_type, ucode_size;
+	unsigned int code_length;
 
 	/*
 	 * If size is less than microcode header size then don't report
@@ -303,7 +304,13 @@
 	if (get_ucode_type(ucode_hdr, &ucode_type))
 		return 0;
 
-	ucode_size = ntohl(ucode_hdr->code_length) * 2;
+	code_length = ntohl(ucode_hdr->code_length);
+	if (code_length >= INT_MAX / 2) {
+		dev_err(dev, "Invalid code_length %u\n", code_length);
+		return -EINVAL;
+	}
+
+	ucode_size = code_length * 2;
 	if (!ucode_size || (size < round_up(ucode_size, 16) +
 	    sizeof(struct otx_cpt_ucode_hdr) + OTX_CPT_UCODE_SIGN_LEN)) {
 		dev_err(dev, "Ucode %s invalid size\n", filename);
@@ -886,6 +893,7 @@
 {
 	struct otx_cpt_ucode_hdr *ucode_hdr;
 	const struct firmware *fw;
+	unsigned int code_length;
 	int ret;
 
 	set_ucode_filename(ucode, ucode_filename);
@@ -896,7 +904,13 @@
 	ucode_hdr = (struct otx_cpt_ucode_hdr *) fw->data;
 	memcpy(ucode->ver_str, ucode_hdr->ver_str, OTX_CPT_UCODE_VER_STR_SZ);
 	ucode->ver_num = ucode_hdr->ver_num;
-	ucode->size = ntohl(ucode_hdr->code_length) * 2;
+	code_length = ntohl(ucode_hdr->code_length);
+	if (code_length >= INT_MAX / 2) {
+		dev_err(dev, "Ucode invalid code_length %u\n", code_length);
+		ret = -EINVAL;
+		goto release_fw;
+	}
+	ucode->size = code_length * 2;
 	if (!ucode->size || (fw->size < round_up(ucode->size, 16)
 	    + sizeof(struct otx_cpt_ucode_hdr) + OTX_CPT_UCODE_SIGN_LEN)) {
 		dev_err(dev, "Ucode %s invalid size\n", ucode_filename);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/octeontx2/otx2_cptlf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/octeontx2/otx2_cptlf.c
@@ -414,8 +414,8 @@
 	return 0;
 
 free_iq:
-	otx2_cpt_free_instruction_queues(lfs);
 	cptlf_hw_cleanup(lfs);
+	otx2_cpt_free_instruction_queues(lfs);
 detach_rsrcs:
 	otx2_cpt_detach_rsrcs_msg(lfs);
 clear_lfs_num:
@@ -425,9 +425,11 @@
 
 void otx2_cptlf_shutdown(struct otx2_cptlfs_info *lfs)
 {
-	lfs->lfs_num = 0;
 	/* Cleanup LFs hardware side */
 	cptlf_hw_cleanup(lfs);
+	/* Free instruction queues */
+	otx2_cpt_free_instruction_queues(lfs);
 	/* Send request to detach LFs */
 	otx2_cpt_detach_rsrcs_msg(lfs);
+	lfs->lfs_num = 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/octeontx2/otx2_cptpf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/octeontx2/otx2_cptpf_main.c
@@ -494,12 +494,11 @@
 {
 	struct otx2_cptpf_dev *cptpf = dev_get_drvdata(dev);
 	int lfs_num;
+	int ret;
 
-	if (kstrtoint(buf, 0, &lfs_num)) {
-		dev_err(dev, "lfs count %d must be in range [1 - %d]\n",
-			lfs_num, num_online_cpus());
-		return -EINVAL;
-	}
+	ret = kstrtoint(buf, 0, &lfs_num);
+	if (ret)
+		return ret;
 	if (lfs_num < 1 || lfs_num > num_online_cpus()) {
 		dev_err(dev, "lfs count %d must be in range [1 - %d]\n",
 			lfs_num, num_online_cpus());
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/octeontx2/otx2_cptpf_ucode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/octeontx2/otx2_cptpf_ucode.c
@@ -29,7 +29,8 @@
 	bool found = false;
 	int i;
 
-	if (eng_grp->g->engs_num > OTX2_CPT_MAX_ENGINES) {
+	if (eng_grp->g->engs_num < 0 ||
+	    eng_grp->g->engs_num > OTX2_CPT_MAX_ENGINES) {
 		dev_err(dev, "unsupported number of engines %d on octeontx2\n",
 			eng_grp->g->engs_num);
 		return bmap;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/octeontx2/otx2_cptvf_algs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/octeontx2/otx2_cptvf_algs.c
@@ -1274,6 +1274,7 @@
 					  req->base.complete, req->base.data);
 		aead_request_set_crypt(&rctx->fbk_req, req->src,
 				       req->dst, req->cryptlen, req->iv);
+		aead_request_set_ad(&rctx->fbk_req, req->assoclen);
 		ret = is_enc ? crypto_aead_encrypt(&rctx->fbk_req) :
 			       crypto_aead_decrypt(&rctx->fbk_req);
 	} else {
@@ -1633,16 +1634,13 @@
 {
 	int i, err = 0;
 
-	if (!IS_ENABLED(CONFIG_DM_CRYPT)) {
-		for (i = 0; i < ARRAY_SIZE(otx2_cpt_skciphers); i++)
-			otx2_cpt_skciphers[i].base.cra_flags &=
-							~CRYPTO_ALG_DEAD;
-
-		err = crypto_register_skciphers(otx2_cpt_skciphers,
-						ARRAY_SIZE(otx2_cpt_skciphers));
-		if (err)
-			return err;
-	}
+	for (i = 0; i < ARRAY_SIZE(otx2_cpt_skciphers); i++)
+		otx2_cpt_skciphers[i].base.cra_flags &= ~CRYPTO_ALG_DEAD;
+
+	err = crypto_register_skciphers(otx2_cpt_skciphers,
+					ARRAY_SIZE(otx2_cpt_skciphers));
+	if (err)
+		return err;
 
 	for (i = 0; i < ARRAY_SIZE(otx2_cpt_aeads); i++)
 		otx2_cpt_aeads[i].base.cra_flags &= ~CRYPTO_ALG_DEAD;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/marvell/octeontx2/otx2_cptvf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/marvell/octeontx2/otx2_cptvf_main.c
@@ -249,8 +249,11 @@
 	otx2_cptlf_unregister_interrupts(lfs);
 	/* Cleanup LFs software side */
 	lf_sw_cleanup(lfs);
+	/* Free instruction queues */
+	otx2_cpt_free_instruction_queues(lfs);
 	/* Send request to detach LFs */
 	otx2_cpt_detach_rsrcs_msg(lfs);
+	lfs->lfs_num = 0;
 }
 
 static int cptvf_lf_init(struct otx2_cptvf_dev *cptvf)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/mxs-dcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/mxs-dcp.c
@@ -331,7 +331,7 @@
 		memset(key + AES_KEYSIZE_128, 0, AES_KEYSIZE_128);
 	}
 
-	for_each_sg(req->src, src, sg_nents(src), i) {
+	for_each_sg(req->src, src, sg_nents(req->src), i) {
 		src_buf = sg_virt(src);
 		len = sg_dma_len(src);
 		tlen += len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/n2_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/n2_core.c
@@ -1229,6 +1229,7 @@
 	const u8	*hash_init;
 	u8		hw_op_hashsz;
 	u8		digest_size;
+	u8		statesize;
 	u8		block_size;
 	u8		auth_type;
 	u8		hmac_type;
@@ -1260,6 +1261,7 @@
 	  .hmac_type	= AUTH_TYPE_HMAC_MD5,
 	  .hw_op_hashsz	= MD5_DIGEST_SIZE,
 	  .digest_size	= MD5_DIGEST_SIZE,
+	  .statesize	= sizeof(struct md5_state),
 	  .block_size	= MD5_HMAC_BLOCK_SIZE },
 	{ .name		= "sha1",
 	  .hash_zero	= sha1_zero_message_hash,
@@ -1268,6 +1270,7 @@
 	  .hmac_type	= AUTH_TYPE_HMAC_SHA1,
 	  .hw_op_hashsz	= SHA1_DIGEST_SIZE,
 	  .digest_size	= SHA1_DIGEST_SIZE,
+	  .statesize	= sizeof(struct sha1_state),
 	  .block_size	= SHA1_BLOCK_SIZE },
 	{ .name		= "sha256",
 	  .hash_zero	= sha256_zero_message_hash,
@@ -1276,6 +1279,7 @@
 	  .hmac_type	= AUTH_TYPE_HMAC_SHA256,
 	  .hw_op_hashsz	= SHA256_DIGEST_SIZE,
 	  .digest_size	= SHA256_DIGEST_SIZE,
+	  .statesize	= sizeof(struct sha256_state),
 	  .block_size	= SHA256_BLOCK_SIZE },
 	{ .name		= "sha224",
 	  .hash_zero	= sha224_zero_message_hash,
@@ -1284,6 +1288,7 @@
 	  .hmac_type	= AUTH_TYPE_RESERVED,
 	  .hw_op_hashsz	= SHA256_DIGEST_SIZE,
 	  .digest_size	= SHA224_DIGEST_SIZE,
+	  .statesize	= sizeof(struct sha256_state),
 	  .block_size	= SHA224_BLOCK_SIZE },
 };
 #define NUM_HASH_TMPLS ARRAY_SIZE(hash_tmpls)
@@ -1424,6 +1429,7 @@
 
 	halg = &ahash->halg;
 	halg->digestsize = tmpl->digest_size;
+	halg->statesize = tmpl->statesize;
 
 	base = &halg->base;
 	snprintf(base->cra_name, CRYPTO_MAX_ALG_NAME, "%s", tmpl->name);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/nx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/nx/Makefile
@@ -1,7 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_CRYPTO_DEV_NX_ENCRYPT) += nx-crypto.o
 nx-crypto-objs := nx.o \
-		  nx_debugfs.o \
 		  nx-aes-cbc.o \
 		  nx-aes-ecb.o \
 		  nx-aes-gcm.o \
@@ -11,6 +10,7 @@
 		  nx-sha256.o \
 		  nx-sha512.o
 
+nx-crypto-$(CONFIG_DEBUG_FS) += nx_debugfs.o
 obj-$(CONFIG_CRYPTO_DEV_NX_COMPRESS_PSERIES) += nx-compress-pseries.o nx-compress.o
 obj-$(CONFIG_CRYPTO_DEV_NX_COMPRESS_POWERNV) += nx-compress-powernv.o nx-compress.o
 nx-compress-objs := nx-842.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/nx/nx-common-powernv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/nx/nx-common-powernv.c
@@ -827,7 +827,7 @@
 		goto err_out;
 
 	vas_init_rx_win_attr(&rxattr, coproc->ct);
-	rxattr.rx_fifo = (void *)rx_fifo;
+	rxattr.rx_fifo = rx_fifo;
 	rxattr.rx_fifo_size = fifo_size;
 	rxattr.lnotify_lpid = lpid;
 	rxattr.lnotify_pid = pid;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/nx/nx-common-pseries.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/nx/nx-common-pseries.c
@@ -1142,6 +1142,7 @@
 {
 	struct hv_vas_all_caps *hv_caps;
 	struct hv_nx_cop_caps *hv_nxc;
+	u64 feat;
 	int rc;
 
 	hv_caps = kmalloc(sizeof(*hv_caps), GFP_KERNEL);
@@ -1152,27 +1153,26 @@
 	 */
 	rc = h_query_vas_capabilities(H_QUERY_NX_CAPABILITIES, 0,
 					  (u64)virt_to_phys(hv_caps));
+	if (!rc)
+		feat = be64_to_cpu(hv_caps->feat_type);
+	kfree(hv_caps);
 	if (rc)
-		goto out;
+		return;
+	if (!(feat & VAS_NX_GZIP_FEAT_BIT))
+		return;
 
-	caps_feat = be64_to_cpu(hv_caps->feat_type);
 	/*
 	 * NX-GZIP feature available
 	 */
-	if (caps_feat & VAS_NX_GZIP_FEAT_BIT) {
-		hv_nxc = kmalloc(sizeof(*hv_nxc), GFP_KERNEL);
-		if (!hv_nxc)
-			goto out;
-		/*
-		 * Get capabilities for NX-GZIP feature
-		 */
-		rc = h_query_vas_capabilities(H_QUERY_NX_CAPABILITIES,
-						  VAS_NX_GZIP_FEAT,
-						  (u64)virt_to_phys(hv_nxc));
-	} else {
-		pr_err("NX-GZIP feature is not available\n");
-		rc = -EINVAL;
-	}
+	hv_nxc = kmalloc(sizeof(*hv_nxc), GFP_KERNEL);
+	if (!hv_nxc)
+		return;
+	/*
+	 * Get capabilities for NX-GZIP feature
+	 */
+	rc = h_query_vas_capabilities(H_QUERY_NX_CAPABILITIES,
+					  VAS_NX_GZIP_FEAT,
+					  (u64)virt_to_phys(hv_nxc));
 
 	if (!rc) {
 		nx_cop_caps.descriptor = be64_to_cpu(hv_nxc->descriptor);
@@ -1182,13 +1182,10 @@
 				be64_to_cpu(hv_nxc->min_compress_len);
 		nx_cop_caps.min_decompress_len =
 				be64_to_cpu(hv_nxc->min_decompress_len);
-	} else {
-		caps_feat = 0;
+		caps_feat = feat;
 	}
 
 	kfree(hv_nxc);
-out:
-	kfree(hv_caps);
 }
 
 static const struct vio_device_id nx842_vio_driver_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/nx/nx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/nx/nx.h
@@ -170,8 +170,8 @@
 void nx_debugfs_init(struct nx_crypto_driver *);
 void nx_debugfs_fini(struct nx_crypto_driver *);
 #else
-#define NX_DEBUGFS_INIT(drv)	(0)
-#define NX_DEBUGFS_FINI(drv)	(0)
+#define NX_DEBUGFS_INIT(drv)	do {} while (0)
+#define NX_DEBUGFS_FINI(drv)	do {} while (0)
 #endif
 
 #define NX_PAGE_NUM(x)		((u64)(x) & 0xfffffffffffff000ULL)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/omap-aes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/omap-aes.c
@@ -1302,7 +1302,7 @@
 
 static int omap_aes_resume(struct device *dev)
 {
-	pm_runtime_resume_and_get(dev);
+	pm_runtime_get_sync(dev);
 	return 0;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/omap-sham.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/omap-sham.c
@@ -2114,7 +2114,7 @@
 
 	pm_runtime_enable(dev);
 
-	err = pm_runtime_get_sync(dev);
+	err = pm_runtime_resume_and_get(dev);
 	if (err < 0) {
 		dev_err(dev, "failed to get sync: %d\n", err);
 		goto err_pm;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_4xxx/adf_4xxx_hw_data.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_4xxx/adf_4xxx_hw_data.c
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: (BSD-3-Clause OR GPL-2.0-only)
 /* Copyright(c) 2020 Intel Corporation */
+#include <linux/iopoll.h>
 #include <adf_accel_devices.h>
 #include <adf_common_drv.h>
 #include <adf_pf2vf_msg.h>
@@ -161,6 +162,35 @@
 	ADF_CSR_WR(addr, ADF_4XXX_SMIAPF_MASK_OFFSET, 0);
 }
 
+static int adf_init_device(struct adf_accel_dev *accel_dev)
+{
+	void __iomem *addr;
+	u32 status;
+	u32 csr;
+	int ret;
+
+	addr = (&GET_BARS(accel_dev)[ADF_4XXX_PMISC_BAR])->virt_addr;
+
+	/* Temporarily mask PM interrupt */
+	csr = ADF_CSR_RD(addr, ADF_4XXX_ERRMSK2);
+	csr |= ADF_4XXX_PM_SOU;
+	ADF_CSR_WR(addr, ADF_4XXX_ERRMSK2, csr);
+
+	/* Set DRV_ACTIVE bit to power up the device */
+	ADF_CSR_WR(addr, ADF_4XXX_PM_INTERRUPT, ADF_4XXX_PM_DRV_ACTIVE);
+
+	/* Poll status register to make sure the device is powered up */
+	ret = read_poll_timeout(ADF_CSR_RD, status,
+				status & ADF_4XXX_PM_INIT_STATE,
+				ADF_4XXX_PM_POLL_DELAY_US,
+				ADF_4XXX_PM_POLL_TIMEOUT_US, true, addr,
+				ADF_4XXX_PM_STATUS);
+	if (ret)
+		dev_err(&GET_DEV(accel_dev), "Failed to power up the device\n");
+
+	return ret;
+}
+
 static int adf_enable_pf2vf_comms(struct adf_accel_dev *accel_dev)
 {
 	return 0;
@@ -215,6 +245,7 @@
 	hw_data->exit_arb = adf_exit_arb;
 	hw_data->get_arb_mapping = adf_get_arbiter_mapping;
 	hw_data->enable_ints = adf_enable_ints;
+	hw_data->init_device = adf_init_device;
 	hw_data->reset_device = adf_reset_flr;
 	hw_data->admin_ae_mask = ADF_4XXX_ADMIN_AE_MASK;
 	hw_data->uof_get_num_objs = uof_get_num_objs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_4xxx/adf_4xxx_hw_data.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_4xxx/adf_4xxx_hw_data.h
@@ -62,6 +62,16 @@
 #define ADF_4XXX_ADMINMSGLR_OFFSET	(0x500578)
 #define ADF_4XXX_MAILBOX_BASE_OFFSET	(0x600970)
 
+/* Power management */
+#define ADF_4XXX_PM_POLL_DELAY_US	20
+#define ADF_4XXX_PM_POLL_TIMEOUT_US	USEC_PER_SEC
+#define ADF_4XXX_PM_STATUS		(0x50A00C)
+#define ADF_4XXX_PM_INTERRUPT		(0x50A028)
+#define ADF_4XXX_PM_DRV_ACTIVE		BIT(20)
+#define ADF_4XXX_PM_INIT_STATE		BIT(21)
+/* Power management source in ERRSOU2 and ERRMSK2 */
+#define ADF_4XXX_PM_SOU			BIT(18)
+
 /* Firmware Binaries */
 #define ADF_4XXX_FW		"qat_4xxx.bin"
 #define ADF_4XXX_MMP		"qat_4xxx_mmp.bin"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/Makefile
@@ -15,6 +15,7 @@
 	qat_crypto.o \
 	qat_algs.o \
 	qat_asym_algs.o \
+	qat_algs_send.o \
 	qat_uclo.o \
 	qat_hal.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_accel_devices.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_accel_devices.h
@@ -24,7 +24,7 @@
 #define ADF_PCI_MAX_BARS 3
 #define ADF_DEVICE_NAME_LENGTH 32
 #define ADF_ETR_MAX_RINGS_PER_BANK 16
-#define ADF_MAX_MSIX_VECTOR_NAME 16
+#define ADF_MAX_MSIX_VECTOR_NAME 48
 #define ADF_DEVICE_NAME_PREFIX "qat_"
 
 enum adf_accel_capabilities {
@@ -166,6 +166,7 @@
 	int (*init_arb)(struct adf_accel_dev *accel_dev);
 	void (*exit_arb)(struct adf_accel_dev *accel_dev);
 	const u32 *(*get_arb_mapping)(void);
+	int (*init_device)(struct adf_accel_dev *accel_dev);
 	void (*disable_iov)(struct adf_accel_dev *accel_dev);
 	void (*configure_iov_threads)(struct adf_accel_dev *accel_dev,
 				      bool enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_aer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_aer.c
@@ -95,7 +95,8 @@
 	if (adf_dev_init(accel_dev) || adf_dev_start(accel_dev)) {
 		/* The device hanged and we can't restart it so stop here */
 		dev_err(&GET_DEV(accel_dev), "Restart device failed\n");
-		kfree(reset_data);
+		if (reset_data->mode == ADF_DEV_RESET_ASYNC)
+			kfree(reset_data);
 		WARN(1, "QAT: device restart failed. Device is unusable\n");
 		return;
 	}
@@ -103,10 +104,10 @@
 	clear_bit(ADF_STATUS_RESTARTING, &accel_dev->status);
 
 	/* The dev is back alive. Notify the caller if in sync mode */
-	if (reset_data->mode == ADF_DEV_RESET_SYNC)
-		complete(&reset_data->compl);
-	else
+	if (reset_data->mode == ADF_DEV_RESET_ASYNC)
 		kfree(reset_data);
+	else
+		complete(&reset_data->compl);
 }
 
 static int adf_dev_aer_schedule_reset(struct adf_accel_dev *accel_dev,
@@ -138,6 +139,7 @@
 		if (!timeout) {
 			dev_err(&GET_DEV(accel_dev),
 				"Reset device timeout expired\n");
+			cancel_work_sync(&reset_data->reset_work);
 			ret = -EFAULT;
 		}
 		kfree(reset_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_common_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_common_drv.h
@@ -49,11 +49,6 @@
 	struct list_head list;
 };
 
-static inline int get_current_node(void)
-{
-	return topology_physical_package_id(raw_smp_processor_id());
-}
-
 int adf_service_register(struct service_hndl *service);
 int adf_service_unregister(struct service_hndl *service);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_gen2_hw_data.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_gen2_hw_data.c
@@ -161,21 +161,33 @@
 	u32 legfuses;
 	u32 capabilities = ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC |
 			   ICP_ACCEL_CAPABILITIES_CRYPTO_ASYMMETRIC |
-			   ICP_ACCEL_CAPABILITIES_AUTHENTICATION;
+			   ICP_ACCEL_CAPABILITIES_AUTHENTICATION |
+			   ICP_ACCEL_CAPABILITIES_CIPHER |
+			   ICP_ACCEL_CAPABILITIES_COMPRESSION;
 
 	/* Read accelerator capabilities mask */
 	pci_read_config_dword(pdev, ADF_DEVICE_LEGFUSE_OFFSET, &legfuses);
 
-	if (legfuses & ICP_ACCEL_MASK_CIPHER_SLICE)
+	/* A set bit in legfuses means the feature is OFF in this SKU */
+	if (legfuses & ICP_ACCEL_MASK_CIPHER_SLICE) {
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC;
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_CIPHER;
+	}
 	if (legfuses & ICP_ACCEL_MASK_PKE_SLICE)
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_CRYPTO_ASYMMETRIC;
-	if (legfuses & ICP_ACCEL_MASK_AUTH_SLICE)
+	if (legfuses & ICP_ACCEL_MASK_AUTH_SLICE) {
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_AUTHENTICATION;
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_CIPHER;
+	}
+	if (legfuses & ICP_ACCEL_MASK_COMPRESS_SLICE)
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_COMPRESSION;
 
 	if ((straps | fuses) & ADF_POWERGATE_PKE)
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_CRYPTO_ASYMMETRIC;
 
+	if ((straps | fuses) & ADF_POWERGATE_DC)
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_COMPRESSION;
+
 	return capabilities;
 }
 EXPORT_SYMBOL_GPL(adf_gen2_get_accel_cap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_gen2_hw_data.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_gen2_hw_data.h
@@ -111,6 +111,7 @@
 	(ADF_ARB_REG_SLOT * (index)), value)
 
 /* Power gating */
+#define ADF_POWERGATE_DC		BIT(23)
 #define ADF_POWERGATE_PKE		BIT(24)
 
 /* WDT timers
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_gen4_hw_data.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_gen4_hw_data.h
@@ -99,7 +99,7 @@
  * Timeout is in cycles. Clock speed may vary across products but this
  * value should be a few milli-seconds.
  */
-#define ADF_SSM_WDT_DEFAULT_VALUE	0x200000
+#define ADF_SSM_WDT_DEFAULT_VALUE	0x7000000ULL
 #define ADF_SSM_WDT_PKE_DEFAULT_VALUE	0x8000000
 #define ADF_SSMWDTL_OFFSET		0x54
 #define ADF_SSMWDTH_OFFSET		0x5C
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_hw_arbiter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_hw_arbiter.c
@@ -90,10 +90,6 @@
 
 	hw_data->get_arb_info(&info);
 
-	/* Reset arbiter configuration */
-	for (i = 0; i < ADF_ARB_NUM; i++)
-		WRITE_CSR_ARB_SARCONFIG(csr, arb_off, i, 0);
-
 	/* Unmap worker threads to service arbiters */
 	for (i = 0; i < hw_data->num_engines; i++)
 		WRITE_CSR_ARB_WT2SAM(csr, arb_off, wt_off, i, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_init.c
@@ -79,6 +79,11 @@
 		return -EFAULT;
 	}
 
+	if (hw_data->init_device && hw_data->init_device(accel_dev)) {
+		dev_err(&GET_DEV(accel_dev), "Failed to initialize device\n");
+		return -EFAULT;
+	}
+
 	if (hw_data->init_admin_comms && hw_data->init_admin_comms(accel_dev)) {
 		dev_err(&GET_DEV(accel_dev), "Failed initialize admin comms\n");
 		return -EFAULT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_pf2vf_msg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_pf2vf_msg.c
@@ -117,37 +117,19 @@
 
 	mutex_lock(lock);
 
-	/* Check if PF2VF CSR is in use by remote function */
+	/* Check if the PFVF CSR is in use by remote function */
 	val = ADF_CSR_RD(pmisc_bar_addr, pf2vf_offset);
 	if ((val & remote_in_use_mask) == remote_in_use_pattern) {
 		dev_dbg(&GET_DEV(accel_dev),
-			"PF2VF CSR in use by remote function\n");
+			"PFVF CSR in use by remote function\n");
 		ret = -EBUSY;
 		goto out;
 	}
 
-	/* Attempt to get ownership of PF2VF CSR */
 	msg &= ~local_in_use_mask;
 	msg |= local_in_use_pattern;
-	ADF_CSR_WR(pmisc_bar_addr, pf2vf_offset, msg);
 
-	/* Wait in case remote func also attempting to get ownership */
-	msleep(ADF_IOV_MSG_COLLISION_DETECT_DELAY);
-
-	val = ADF_CSR_RD(pmisc_bar_addr, pf2vf_offset);
-	if ((val & local_in_use_mask) != local_in_use_pattern) {
-		dev_dbg(&GET_DEV(accel_dev),
-			"PF2VF CSR in use by remote - collision detected\n");
-		ret = -EBUSY;
-		goto out;
-	}
-
-	/*
-	 * This function now owns the PV2VF CSR.  The IN_USE_BY pattern must
-	 * remain in the PF2VF CSR for all writes including ACK from remote
-	 * until this local function relinquishes the CSR.  Send the message
-	 * by interrupting the remote.
-	 */
+	/* Attempt to get ownership of the PFVF CSR */
 	ADF_CSR_WR(pmisc_bar_addr, pf2vf_offset, msg | int_bit);
 
 	/* Wait for confirmation from remote func it received the message */
@@ -162,7 +144,14 @@
 		ret = -EIO;
 	}
 
-	/* Finished with PF2VF CSR; relinquish it and leave msg in CSR */
+	if (val != msg) {
+		dev_dbg(&GET_DEV(accel_dev),
+			"Collision - PFVF CSR overwritten by remote function\n");
+		ret = -EIO;
+		goto out;
+	}
+
+	/* Finished with the PFVF CSR; relinquish it and leave msg in CSR */
 	ADF_CSR_WR(pmisc_bar_addr, pf2vf_offset, val & ~local_in_use_mask);
 out:
 	mutex_unlock(lock);
@@ -170,12 +159,13 @@
 }
 
 /**
- * adf_iov_putmsg() - send PF2VF message
+ * adf_iov_putmsg() - send PFVF message
  * @accel_dev:  Pointer to acceleration device.
  * @msg:	Message to send
- * @vf_nr:	VF number to which the message will be sent
+ * @vf_nr:	VF number to which the message will be sent if on PF, ignored
+ *		otherwise
  *
- * Function sends a message from the PF to a VF
+ * Function sends a message through the PFVF channel
  *
  * Return: 0 on success, error code otherwise.
  */
@@ -204,6 +194,11 @@
 
 	/* Read message from the VF */
 	msg = ADF_CSR_RD(pmisc_addr, hw_data->get_pf2vf_offset(vf_nr));
+	if (!(msg & ADF_VF2PF_INT)) {
+		dev_info(&GET_DEV(accel_dev),
+			 "Spurious VF2PF interrupt, msg %X. Ignored\n", msg);
+		goto out;
+	}
 
 	/* To ACK, clear the VF2PFINT bit */
 	msg &= ~ADF_VF2PF_INT;
@@ -287,6 +282,7 @@
 	if (resp && adf_iov_putmsg(accel_dev, resp, vf_nr))
 		dev_err(&GET_DEV(accel_dev), "Failed to send response to VF\n");
 
+out:
 	/* re-enable interrupt on PF from this VF */
 	adf_enable_vf2pf_interrupts(accel_dev, (1 << vf_nr));
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_transport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_transport.c
@@ -8,6 +8,9 @@
 #include "adf_cfg.h"
 #include "adf_common_drv.h"
 
+#define ADF_MAX_RING_THRESHOLD		80
+#define ADF_PERCENT(tot, percent)	(((tot) * (percent)) / 100)
+
 static inline u32 adf_modulo(u32 data, u32 shift)
 {
 	u32 div = data >> shift;
@@ -77,6 +80,11 @@
 				      bank->irq_mask);
 }
 
+bool adf_ring_nearly_full(struct adf_etr_ring_data *ring)
+{
+	return atomic_read(ring->inflights) > ring->threshold;
+}
+
 int adf_send_message(struct adf_etr_ring_data *ring, u32 *msg)
 {
 	struct adf_hw_csr_ops *csr_ops = GET_CSR_OPS(ring->bank->accel_dev);
@@ -217,6 +225,7 @@
 	struct adf_etr_bank_data *bank;
 	struct adf_etr_ring_data *ring;
 	char val[ADF_CFG_MAX_VAL_LEN_IN_BYTES];
+	int max_inflights;
 	u32 ring_num;
 	int ret;
 
@@ -263,6 +272,8 @@
 	ring->ring_size = adf_verify_ring_size(msg_size, num_msgs);
 	ring->head = 0;
 	ring->tail = 0;
+	max_inflights = ADF_MAX_INFLIGHTS(ring->ring_size, ring->msg_size);
+	ring->threshold = ADF_PERCENT(max_inflights, ADF_MAX_RING_THRESHOLD);
 	atomic_set(ring->inflights, 0);
 	ret = adf_init_ring(ring);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_transport.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_transport.h
@@ -14,6 +14,7 @@
 		    const char *ring_name, adf_callback_fn callback,
 		    int poll_mode, struct adf_etr_ring_data **ring_ptr);
 
+bool adf_ring_nearly_full(struct adf_etr_ring_data *ring);
 int adf_send_message(struct adf_etr_ring_data *ring, u32 *msg);
 void adf_remove_ring(struct adf_etr_ring_data *ring);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_transport_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_transport_debug.c
@@ -90,7 +90,7 @@
 int adf_ring_debugfs_add(struct adf_etr_ring_data *ring, const char *name)
 {
 	struct adf_etr_ring_debug_entry *ring_debug;
-	char entry_name[8];
+	char entry_name[16];
 
 	ring_debug = kzalloc(sizeof(*ring_debug), GFP_KERNEL);
 	if (!ring_debug)
@@ -192,7 +192,7 @@
 {
 	struct adf_accel_dev *accel_dev = bank->accel_dev;
 	struct dentry *parent = accel_dev->transport->debug;
-	char name[8];
+	char name[16];
 
 	snprintf(name, sizeof(name), "bank_%02d", bank->bank_number);
 	bank->bank_debug_dir = debugfs_create_dir(name, parent);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_transport_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_transport_internal.h
@@ -22,6 +22,7 @@
 	spinlock_t lock;	/* protects ring data struct */
 	u16 head;
 	u16 tail;
+	u32 threshold;
 	u8 ring_number;
 	u8 ring_size;
 	u8 msg_size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/adf_vf_isr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/adf_vf_isr.c
@@ -101,6 +101,11 @@
 
 	/* Read the message from PF */
 	msg = ADF_CSR_RD(pmisc_bar_addr, hw_data->get_pf2vf_offset(0));
+	if (!(msg & ADF_PF2VF_INT)) {
+		dev_info(&GET_DEV(accel_dev),
+			 "Spurious PF2VF interrupt, msg %X. Ignored\n", msg);
+		goto out;
+	}
 
 	if (!(msg & ADF_PF2VF_MSGORIGIN_SYSTEM))
 		/* Ignore legacy non-system (non-kernel) PF2VF messages */
@@ -149,6 +154,7 @@
 	msg &= ~ADF_PF2VF_INT;
 	ADF_CSR_WR(pmisc_bar_addr, hw_data->get_pf2vf_offset(0), msg);
 
+out:
 	/* Re-enable PF2VF interrupts */
 	adf_enable_pf2vf_interrupts(accel_dev);
 	return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/qat_algs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/qat_algs.c
@@ -17,7 +17,7 @@
 #include <crypto/xts.h>
 #include <linux/dma-mapping.h>
 #include "adf_accel_devices.h"
-#include "adf_transport.h"
+#include "qat_algs_send.h"
 #include "adf_common_drv.h"
 #include "qat_crypto.h"
 #include "icp_qat_hw.h"
@@ -46,19 +46,6 @@
 static DEFINE_MUTEX(algs_lock);
 static unsigned int active_devs;
 
-struct qat_alg_buf {
-	u32 len;
-	u32 resrvd;
-	u64 addr;
-} __packed;
-
-struct qat_alg_buf_list {
-	u64 resrvd;
-	u32 num_bufs;
-	u32 num_mapped_bufs;
-	struct qat_alg_buf bufers[];
-} __packed __aligned(64);
-
 /* Common content descriptor */
 struct qat_alg_cd {
 	union {
@@ -447,8 +434,8 @@
 	} else if (aes_v2_capable && mode == ICP_QAT_HW_CIPHER_CTR_MODE) {
 		ICP_QAT_FW_LA_SLICE_TYPE_SET(header->serv_specif_flags,
 					     ICP_QAT_FW_LA_USE_UCS_SLICE_TYPE);
-		keylen = round_up(keylen, 16);
 		memcpy(cd->ucs_aes.key, key, keylen);
+		keylen = round_up(keylen, 16);
 	} else {
 		memcpy(cd->aes.key, key, keylen);
 	}
@@ -618,7 +605,7 @@
 {
 	struct qat_alg_aead_ctx *ctx = crypto_aead_ctx(tfm);
 	struct qat_crypto_instance *inst = NULL;
-	int node = get_current_node();
+	int node = numa_node_id();
 	struct device *dev;
 	int ret;
 
@@ -686,14 +673,20 @@
 	dma_addr_t blpout = qat_req->buf.bloutp;
 	size_t sz = qat_req->buf.sz;
 	size_t sz_out = qat_req->buf.sz_out;
+	int bl_dma_dir;
 	int i;
 
+	bl_dma_dir = blp != blpout ? DMA_TO_DEVICE : DMA_BIDIRECTIONAL;
+
 	for (i = 0; i < bl->num_bufs; i++)
 		dma_unmap_single(dev, bl->bufers[i].addr,
-				 bl->bufers[i].len, DMA_BIDIRECTIONAL);
+				 bl->bufers[i].len, bl_dma_dir);
 
 	dma_unmap_single(dev, blp, sz, DMA_TO_DEVICE);
-	kfree(bl);
+
+	if (!qat_req->buf.sgl_src_valid)
+		kfree(bl);
+
 	if (blp != blpout) {
 		/* If out of place operation dma unmap only data */
 		int bufless = blout->num_bufs - blout->num_mapped_bufs;
@@ -701,17 +694,20 @@
 		for (i = bufless; i < blout->num_bufs; i++) {
 			dma_unmap_single(dev, blout->bufers[i].addr,
 					 blout->bufers[i].len,
-					 DMA_BIDIRECTIONAL);
+					 DMA_FROM_DEVICE);
 		}
 		dma_unmap_single(dev, blpout, sz_out, DMA_TO_DEVICE);
-		kfree(blout);
+
+		if (!qat_req->buf.sgl_dst_valid)
+			kfree(blout);
 	}
 }
 
 static int qat_alg_sgl_to_bufl(struct qat_crypto_instance *inst,
 			       struct scatterlist *sgl,
 			       struct scatterlist *sglout,
-			       struct qat_crypto_request *qat_req)
+			       struct qat_crypto_request *qat_req,
+			       gfp_t flags)
 {
 	struct device *dev = &GET_DEV(inst->accel_dev);
 	int i, sg_nctr = 0;
@@ -721,15 +717,27 @@
 	dma_addr_t blp = DMA_MAPPING_ERROR;
 	dma_addr_t bloutp = DMA_MAPPING_ERROR;
 	struct scatterlist *sg;
-	size_t sz_out, sz = struct_size(bufl, bufers, n + 1);
+	size_t sz_out, sz = struct_size(bufl, bufers, n);
+	int node = dev_to_node(&GET_DEV(inst->accel_dev));
+	int bufl_dma_dir;
 
 	if (unlikely(!n))
 		return -EINVAL;
 
-	bufl = kzalloc_node(sz, GFP_ATOMIC,
-			    dev_to_node(&GET_DEV(inst->accel_dev)));
-	if (unlikely(!bufl))
-		return -ENOMEM;
+	qat_req->buf.sgl_src_valid = false;
+	qat_req->buf.sgl_dst_valid = false;
+
+	if (n > QAT_MAX_BUFF_DESC) {
+		bufl = kzalloc_node(sz, flags, node);
+		if (unlikely(!bufl))
+			return -ENOMEM;
+	} else {
+		bufl = &qat_req->buf.sgl_src.sgl_hdr;
+		memset(bufl, 0, sizeof(struct qat_alg_buf_list));
+		qat_req->buf.sgl_src_valid = true;
+	}
+
+	bufl_dma_dir = sgl != sglout ? DMA_TO_DEVICE : DMA_BIDIRECTIONAL;
 
 	for_each_sg(sgl, sg, n, i)
 		bufl->bufers[i].addr = DMA_MAPPING_ERROR;
@@ -742,7 +750,7 @@
 
 		bufl->bufers[y].addr = dma_map_single(dev, sg_virt(sg),
 						      sg->length,
-						      DMA_BIDIRECTIONAL);
+						      bufl_dma_dir);
 		bufl->bufers[y].len = sg->length;
 		if (unlikely(dma_mapping_error(dev, bufl->bufers[y].addr)))
 			goto err_in;
@@ -760,12 +768,18 @@
 		struct qat_alg_buf *bufers;
 
 		n = sg_nents(sglout);
-		sz_out = struct_size(buflout, bufers, n + 1);
+		sz_out = struct_size(buflout, bufers, n);
 		sg_nctr = 0;
-		buflout = kzalloc_node(sz_out, GFP_ATOMIC,
-				       dev_to_node(&GET_DEV(inst->accel_dev)));
-		if (unlikely(!buflout))
-			goto err_in;
+
+		if (n > QAT_MAX_BUFF_DESC) {
+			buflout = kzalloc_node(sz_out, flags, node);
+			if (unlikely(!buflout))
+				goto err_in;
+		} else {
+			buflout = &qat_req->buf.sgl_dst.sgl_hdr;
+			memset(buflout, 0, sizeof(struct qat_alg_buf_list));
+			qat_req->buf.sgl_dst_valid = true;
+		}
 
 		bufers = buflout->bufers;
 		for_each_sg(sglout, sg, n, i)
@@ -779,7 +793,7 @@
 
 			bufers[y].addr = dma_map_single(dev, sg_virt(sg),
 							sg->length,
-							DMA_BIDIRECTIONAL);
+							DMA_FROM_DEVICE);
 			if (unlikely(dma_mapping_error(dev, bufers[y].addr)))
 				goto err_out;
 			bufers[y].len = sg->length;
@@ -809,8 +823,10 @@
 		if (!dma_mapping_error(dev, buflout->bufers[i].addr))
 			dma_unmap_single(dev, buflout->bufers[i].addr,
 					 buflout->bufers[i].len,
-					 DMA_BIDIRECTIONAL);
-	kfree(buflout);
+					 DMA_FROM_DEVICE);
+
+	if (!qat_req->buf.sgl_dst_valid)
+		kfree(buflout);
 
 err_in:
 	if (!dma_mapping_error(dev, blp))
@@ -821,9 +837,10 @@
 		if (!dma_mapping_error(dev, bufl->bufers[i].addr))
 			dma_unmap_single(dev, bufl->bufers[i].addr,
 					 bufl->bufers[i].len,
-					 DMA_BIDIRECTIONAL);
+					 bufl_dma_dir);
 
-	kfree(bufl);
+	if (!qat_req->buf.sgl_src_valid)
+		kfree(bufl);
 
 	dev_err(dev, "Failed to map buf for dma\n");
 	return -ENOMEM;
@@ -925,8 +942,25 @@
 	struct icp_qat_fw_la_resp *qat_resp = resp;
 	struct qat_crypto_request *qat_req =
 				(void *)(__force long)qat_resp->opaque_data;
+	struct qat_instance_backlog *backlog = qat_req->alg_req.backlog;
 
 	qat_req->cb(qat_resp, qat_req);
+
+	qat_alg_send_backlog(backlog);
+}
+
+static int qat_alg_send_sym_message(struct qat_crypto_request *qat_req,
+				    struct qat_crypto_instance *inst,
+				    struct crypto_async_request *base)
+{
+	struct qat_alg_req *alg_req = &qat_req->alg_req;
+
+	alg_req->fw_req = (u32 *)&qat_req->req;
+	alg_req->tx_ring = inst->sym_tx;
+	alg_req->base = base;
+	alg_req->backlog = &inst->backlog;
+
+	return qat_alg_send_message(alg_req);
 }
 
 static int qat_alg_aead_dec(struct aead_request *areq)
@@ -939,14 +973,15 @@
 	struct icp_qat_fw_la_auth_req_params *auth_param;
 	struct icp_qat_fw_la_bulk_req *msg;
 	int digst_size = crypto_aead_authsize(aead_tfm);
-	int ret, ctr = 0;
+	gfp_t f = qat_algs_alloc_flags(&areq->base);
+	int ret;
 	u32 cipher_len;
 
 	cipher_len = areq->cryptlen - digst_size;
 	if (cipher_len % AES_BLOCK_SIZE != 0)
 		return -EINVAL;
 
-	ret = qat_alg_sgl_to_bufl(ctx->inst, areq->src, areq->dst, qat_req);
+	ret = qat_alg_sgl_to_bufl(ctx->inst, areq->src, areq->dst, qat_req, f);
 	if (unlikely(ret))
 		return ret;
 
@@ -965,15 +1000,12 @@
 	auth_param = (void *)((u8 *)cipher_param + sizeof(*cipher_param));
 	auth_param->auth_off = 0;
 	auth_param->auth_len = areq->assoclen + cipher_param->cipher_length;
-	do {
-		ret = adf_send_message(ctx->inst->sym_tx, (u32 *)msg);
-	} while (ret == -EAGAIN && ctr++ < 10);
 
-	if (ret == -EAGAIN) {
+	ret = qat_alg_send_sym_message(qat_req, ctx->inst, &areq->base);
+	if (ret == -ENOSPC)
 		qat_alg_free_bufl(ctx->inst, qat_req);
-		return -EBUSY;
-	}
-	return -EINPROGRESS;
+
+	return ret;
 }
 
 static int qat_alg_aead_enc(struct aead_request *areq)
@@ -984,14 +1016,15 @@
 	struct qat_crypto_request *qat_req = aead_request_ctx(areq);
 	struct icp_qat_fw_la_cipher_req_params *cipher_param;
 	struct icp_qat_fw_la_auth_req_params *auth_param;
+	gfp_t f = qat_algs_alloc_flags(&areq->base);
 	struct icp_qat_fw_la_bulk_req *msg;
 	u8 *iv = areq->iv;
-	int ret, ctr = 0;
+	int ret;
 
 	if (areq->cryptlen % AES_BLOCK_SIZE != 0)
 		return -EINVAL;
 
-	ret = qat_alg_sgl_to_bufl(ctx->inst, areq->src, areq->dst, qat_req);
+	ret = qat_alg_sgl_to_bufl(ctx->inst, areq->src, areq->dst, qat_req, f);
 	if (unlikely(ret))
 		return ret;
 
@@ -1013,15 +1046,11 @@
 	auth_param->auth_off = 0;
 	auth_param->auth_len = areq->assoclen + areq->cryptlen;
 
-	do {
-		ret = adf_send_message(ctx->inst->sym_tx, (u32 *)msg);
-	} while (ret == -EAGAIN && ctr++ < 10);
-
-	if (ret == -EAGAIN) {
+	ret = qat_alg_send_sym_message(qat_req, ctx->inst, &areq->base);
+	if (ret == -ENOSPC)
 		qat_alg_free_bufl(ctx->inst, qat_req);
-		return -EBUSY;
-	}
-	return -EINPROGRESS;
+
+	return ret;
 }
 
 static int qat_alg_skcipher_rekey(struct qat_alg_skcipher_ctx *ctx,
@@ -1042,7 +1071,7 @@
 {
 	struct qat_crypto_instance *inst = NULL;
 	struct device *dev;
-	int node = get_current_node();
+	int node = numa_node_id();
 	int ret;
 
 	inst = qat_crypto_get_instance_node(node);
@@ -1173,13 +1202,14 @@
 	struct qat_alg_skcipher_ctx *ctx = crypto_tfm_ctx(tfm);
 	struct qat_crypto_request *qat_req = skcipher_request_ctx(req);
 	struct icp_qat_fw_la_cipher_req_params *cipher_param;
+	gfp_t f = qat_algs_alloc_flags(&req->base);
 	struct icp_qat_fw_la_bulk_req *msg;
-	int ret, ctr = 0;
+	int ret;
 
 	if (req->cryptlen == 0)
 		return 0;
 
-	ret = qat_alg_sgl_to_bufl(ctx->inst, req->src, req->dst, qat_req);
+	ret = qat_alg_sgl_to_bufl(ctx->inst, req->src, req->dst, qat_req, f);
 	if (unlikely(ret))
 		return ret;
 
@@ -1198,15 +1228,11 @@
 
 	qat_alg_set_req_iv(qat_req);
 
-	do {
-		ret = adf_send_message(ctx->inst->sym_tx, (u32 *)msg);
-	} while (ret == -EAGAIN && ctr++ < 10);
-
-	if (ret == -EAGAIN) {
+	ret = qat_alg_send_sym_message(qat_req, ctx->inst, &req->base);
+	if (ret == -ENOSPC)
 		qat_alg_free_bufl(ctx->inst, qat_req);
-		return -EBUSY;
-	}
-	return -EINPROGRESS;
+
+	return ret;
 }
 
 static int qat_alg_skcipher_blk_encrypt(struct skcipher_request *req)
@@ -1242,13 +1268,14 @@
 	struct qat_alg_skcipher_ctx *ctx = crypto_tfm_ctx(tfm);
 	struct qat_crypto_request *qat_req = skcipher_request_ctx(req);
 	struct icp_qat_fw_la_cipher_req_params *cipher_param;
+	gfp_t f = qat_algs_alloc_flags(&req->base);
 	struct icp_qat_fw_la_bulk_req *msg;
-	int ret, ctr = 0;
+	int ret;
 
 	if (req->cryptlen == 0)
 		return 0;
 
-	ret = qat_alg_sgl_to_bufl(ctx->inst, req->src, req->dst, qat_req);
+	ret = qat_alg_sgl_to_bufl(ctx->inst, req->src, req->dst, qat_req, f);
 	if (unlikely(ret))
 		return ret;
 
@@ -1268,15 +1295,11 @@
 	qat_alg_set_req_iv(qat_req);
 	qat_alg_update_iv(qat_req);
 
-	do {
-		ret = adf_send_message(ctx->inst->sym_tx, (u32 *)msg);
-	} while (ret == -EAGAIN && ctr++ < 10);
-
-	if (ret == -EAGAIN) {
+	ret = qat_alg_send_sym_message(qat_req, ctx->inst, &req->base);
+	if (ret == -ENOSPC)
 		qat_alg_free_bufl(ctx->inst, qat_req);
-		return -EBUSY;
-	}
-	return -EINPROGRESS;
+
+	return ret;
 }
 
 static int qat_alg_skcipher_blk_decrypt(struct skcipher_request *req)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/qat_algs_send.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/qat_algs_send.c
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: (BSD-3-Clause OR GPL-2.0-only)
+/* Copyright(c) 2022 Intel Corporation */
+#include "adf_transport.h"
+#include "qat_algs_send.h"
+#include "qat_crypto.h"
+
+#define ADF_MAX_RETRIES		20
+
+static int qat_alg_send_message_retry(struct qat_alg_req *req)
+{
+	int ret = 0, ctr = 0;
+
+	do {
+		ret = adf_send_message(req->tx_ring, req->fw_req);
+	} while (ret == -EAGAIN && ctr++ < ADF_MAX_RETRIES);
+
+	if (ret == -EAGAIN)
+		return -ENOSPC;
+
+	return -EINPROGRESS;
+}
+
+void qat_alg_send_backlog(struct qat_instance_backlog *backlog)
+{
+	struct qat_alg_req *req, *tmp;
+
+	spin_lock_bh(&backlog->lock);
+	list_for_each_entry_safe(req, tmp, &backlog->list, list) {
+		if (adf_send_message(req->tx_ring, req->fw_req)) {
+			/* The HW ring is full. Do nothing.
+			 * qat_alg_send_backlog() will be invoked again by
+			 * another callback.
+			 */
+			break;
+		}
+		list_del(&req->list);
+		req->base->complete(req->base, -EINPROGRESS);
+	}
+	spin_unlock_bh(&backlog->lock);
+}
+
+static bool qat_alg_try_enqueue(struct qat_alg_req *req)
+{
+	struct qat_instance_backlog *backlog = req->backlog;
+	struct adf_etr_ring_data *tx_ring = req->tx_ring;
+	u32 *fw_req = req->fw_req;
+
+	/* Check if any request is already backlogged */
+	if (!list_empty(&backlog->list))
+		return false;
+
+	/* Check if ring is nearly full */
+	if (adf_ring_nearly_full(tx_ring))
+		return false;
+
+	/* Try to enqueue to HW ring */
+	if (adf_send_message(tx_ring, fw_req))
+		return false;
+
+	return true;
+}
+
+
+static int qat_alg_send_message_maybacklog(struct qat_alg_req *req)
+{
+	struct qat_instance_backlog *backlog = req->backlog;
+	int ret = -EINPROGRESS;
+
+	if (qat_alg_try_enqueue(req))
+		return ret;
+
+	spin_lock_bh(&backlog->lock);
+	if (!qat_alg_try_enqueue(req)) {
+		list_add_tail(&req->list, &backlog->list);
+		ret = -EBUSY;
+	}
+	spin_unlock_bh(&backlog->lock);
+
+	return ret;
+}
+
+int qat_alg_send_message(struct qat_alg_req *req)
+{
+	u32 flags = req->base->flags;
+
+	if (flags & CRYPTO_TFM_REQ_MAY_BACKLOG)
+		return qat_alg_send_message_maybacklog(req);
+	else
+		return qat_alg_send_message_retry(req);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/qat_algs_send.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/qat_algs_send.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: (BSD-3-Clause OR GPL-2.0-only) */
+/* Copyright(c) 2022 Intel Corporation */
+#ifndef QAT_ALGS_SEND_H
+#define QAT_ALGS_SEND_H
+
+#include "qat_crypto.h"
+
+int qat_alg_send_message(struct qat_alg_req *req);
+void qat_alg_send_backlog(struct qat_instance_backlog *backlog);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/qat_asym_algs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/qat_asym_algs.c
@@ -12,6 +12,7 @@
 #include <crypto/scatterwalk.h>
 #include "icp_qat_fw_pke.h"
 #include "adf_accel_devices.h"
+#include "qat_algs_send.h"
 #include "adf_transport.h"
 #include "adf_common_drv.h"
 #include "qat_crypto.h"
@@ -135,8 +136,23 @@
 	} areq;
 	int err;
 	void (*cb)(struct icp_qat_fw_pke_resp *resp);
+	struct qat_alg_req alg_req;
 } __aligned(64);
 
+static int qat_alg_send_asym_message(struct qat_asym_request *qat_req,
+				     struct qat_crypto_instance *inst,
+				     struct crypto_async_request *base)
+{
+	struct qat_alg_req *alg_req = &qat_req->alg_req;
+
+	alg_req->fw_req = (u32 *)&qat_req->req;
+	alg_req->tx_ring = inst->pke_tx;
+	alg_req->base = base;
+	alg_req->backlog = &inst->backlog;
+
+	return qat_alg_send_message(alg_req);
+}
+
 static void qat_dh_cb(struct icp_qat_fw_pke_resp *resp)
 {
 	struct qat_asym_request *req = (void *)(__force long)resp->opaque;
@@ -148,24 +164,18 @@
 	err = (err == ICP_QAT_FW_COMN_STATUS_FLAG_OK) ? 0 : -EINVAL;
 
 	if (areq->src) {
-		if (req->src_align)
-			dma_free_coherent(dev, req->ctx.dh->p_size,
-					  req->src_align, req->in.dh.in.b);
-		else
-			dma_unmap_single(dev, req->in.dh.in.b,
-					 req->ctx.dh->p_size, DMA_TO_DEVICE);
+		dma_unmap_single(dev, req->in.dh.in.b, req->ctx.dh->p_size,
+				 DMA_TO_DEVICE);
+		kfree_sensitive(req->src_align);
 	}
 
 	areq->dst_len = req->ctx.dh->p_size;
+	dma_unmap_single(dev, req->out.dh.r, req->ctx.dh->p_size,
+			 DMA_FROM_DEVICE);
 	if (req->dst_align) {
 		scatterwalk_map_and_copy(req->dst_align, areq->dst, 0,
 					 areq->dst_len, 1);
-
-		dma_free_coherent(dev, req->ctx.dh->p_size, req->dst_align,
-				  req->out.dh.r);
-	} else {
-		dma_unmap_single(dev, req->out.dh.r, req->ctx.dh->p_size,
-				 DMA_FROM_DEVICE);
+		kfree_sensitive(req->dst_align);
 	}
 
 	dma_unmap_single(dev, req->phy_in, sizeof(struct qat_dh_input_params),
@@ -213,8 +223,10 @@
 	struct qat_asym_request *qat_req =
 			PTR_ALIGN(kpp_request_ctx(req), 64);
 	struct icp_qat_fw_pke_request *msg = &qat_req->req;
-	int ret, ctr = 0;
+	gfp_t flags = qat_algs_alloc_flags(&req->base);
 	int n_input_params = 0;
+	u8 *vaddr;
+	int ret;
 
 	if (unlikely(!ctx->xa))
 		return -EINVAL;
@@ -223,6 +235,10 @@
 		req->dst_len = ctx->p_size;
 		return -EOVERFLOW;
 	}
+
+	if (req->src_len > ctx->p_size)
+		return -EINVAL;
+
 	memset(msg, '\0', sizeof(*msg));
 	ICP_QAT_FW_PKE_HDR_VALID_FLAG_SET(msg->pke_hdr,
 					  ICP_QAT_FW_COMN_REQ_FLAG_SET);
@@ -271,27 +287,24 @@
 		 */
 		if (sg_is_last(req->src) && req->src_len == ctx->p_size) {
 			qat_req->src_align = NULL;
-			qat_req->in.dh.in.b = dma_map_single(dev,
-							     sg_virt(req->src),
-							     req->src_len,
-							     DMA_TO_DEVICE);
-			if (unlikely(dma_mapping_error(dev,
-						       qat_req->in.dh.in.b)))
-				return ret;
-
+			vaddr = sg_virt(req->src);
 		} else {
 			int shift = ctx->p_size - req->src_len;
 
-			qat_req->src_align = dma_alloc_coherent(dev,
-								ctx->p_size,
-								&qat_req->in.dh.in.b,
-								GFP_KERNEL);
+			qat_req->src_align = kzalloc(ctx->p_size, flags);
 			if (unlikely(!qat_req->src_align))
 				return ret;
 
 			scatterwalk_map_and_copy(qat_req->src_align + shift,
 						 req->src, 0, req->src_len, 0);
+
+			vaddr = qat_req->src_align;
 		}
+
+		qat_req->in.dh.in.b = dma_map_single(dev, vaddr, ctx->p_size,
+						     DMA_TO_DEVICE);
+		if (unlikely(dma_mapping_error(dev, qat_req->in.dh.in.b)))
+			goto unmap_src;
 	}
 	/*
 	 * dst can be of any size in valid range, but HW expects it to be the
@@ -302,32 +315,30 @@
 	 */
 	if (sg_is_last(req->dst) && req->dst_len == ctx->p_size) {
 		qat_req->dst_align = NULL;
-		qat_req->out.dh.r = dma_map_single(dev, sg_virt(req->dst),
-						   req->dst_len,
-						   DMA_FROM_DEVICE);
-
-		if (unlikely(dma_mapping_error(dev, qat_req->out.dh.r)))
-			goto unmap_src;
-
+		vaddr = sg_virt(req->dst);
 	} else {
-		qat_req->dst_align = dma_alloc_coherent(dev, ctx->p_size,
-							&qat_req->out.dh.r,
-							GFP_KERNEL);
+		qat_req->dst_align = kzalloc(ctx->p_size, flags);
 		if (unlikely(!qat_req->dst_align))
 			goto unmap_src;
+
+		vaddr = qat_req->dst_align;
 	}
+	qat_req->out.dh.r = dma_map_single(dev, vaddr, ctx->p_size,
+					   DMA_FROM_DEVICE);
+	if (unlikely(dma_mapping_error(dev, qat_req->out.dh.r)))
+		goto unmap_dst;
 
 	qat_req->in.dh.in_tab[n_input_params] = 0;
 	qat_req->out.dh.out_tab[1] = 0;
 	/* Mapping in.in.b or in.in_g2.xa is the same */
-	qat_req->phy_in = dma_map_single(dev, &qat_req->in.dh.in.b,
-					 sizeof(qat_req->in.dh.in.b),
+	qat_req->phy_in = dma_map_single(dev, &qat_req->in.dh,
+					 sizeof(struct qat_dh_input_params),
 					 DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, qat_req->phy_in)))
 		goto unmap_dst;
 
-	qat_req->phy_out = dma_map_single(dev, &qat_req->out.dh.r,
-					  sizeof(qat_req->out.dh.r),
+	qat_req->phy_out = dma_map_single(dev, &qat_req->out.dh,
+					  sizeof(struct qat_dh_output_params),
 					  DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, qat_req->phy_out)))
 		goto unmap_in_params;
@@ -338,13 +349,13 @@
 	msg->input_param_count = n_input_params;
 	msg->output_param_count = 1;
 
-	do {
-		ret = adf_send_message(ctx->inst->pke_tx, (u32 *)msg);
-	} while (ret == -EBUSY && ctr++ < 100);
+	ret = qat_alg_send_asym_message(qat_req, inst, &req->base);
+	if (ret == -ENOSPC)
+		goto unmap_all;
 
-	if (!ret)
-		return -EINPROGRESS;
+	return ret;
 
+unmap_all:
 	if (!dma_mapping_error(dev, qat_req->phy_out))
 		dma_unmap_single(dev, qat_req->phy_out,
 				 sizeof(struct qat_dh_output_params),
@@ -355,23 +366,17 @@
 				 sizeof(struct qat_dh_input_params),
 				 DMA_TO_DEVICE);
 unmap_dst:
-	if (qat_req->dst_align)
-		dma_free_coherent(dev, ctx->p_size, qat_req->dst_align,
-				  qat_req->out.dh.r);
-	else
-		if (!dma_mapping_error(dev, qat_req->out.dh.r))
-			dma_unmap_single(dev, qat_req->out.dh.r, ctx->p_size,
-					 DMA_FROM_DEVICE);
+	if (!dma_mapping_error(dev, qat_req->out.dh.r))
+		dma_unmap_single(dev, qat_req->out.dh.r, ctx->p_size,
+				 DMA_FROM_DEVICE);
+	kfree_sensitive(qat_req->dst_align);
 unmap_src:
 	if (req->src) {
-		if (qat_req->src_align)
-			dma_free_coherent(dev, ctx->p_size, qat_req->src_align,
-					  qat_req->in.dh.in.b);
-		else
-			if (!dma_mapping_error(dev, qat_req->in.dh.in.b))
-				dma_unmap_single(dev, qat_req->in.dh.in.b,
-						 ctx->p_size,
-						 DMA_TO_DEVICE);
+		if (!dma_mapping_error(dev, qat_req->in.dh.in.b))
+			dma_unmap_single(dev, qat_req->in.dh.in.b,
+					 ctx->p_size,
+					 DMA_TO_DEVICE);
+		kfree_sensitive(qat_req->src_align);
 	}
 	return ret;
 }
@@ -420,14 +425,17 @@
 static void qat_dh_clear_ctx(struct device *dev, struct qat_dh_ctx *ctx)
 {
 	if (ctx->g) {
+		memset(ctx->g, 0, ctx->p_size);
 		dma_free_coherent(dev, ctx->p_size, ctx->g, ctx->dma_g);
 		ctx->g = NULL;
 	}
 	if (ctx->xa) {
+		memset(ctx->xa, 0, ctx->p_size);
 		dma_free_coherent(dev, ctx->p_size, ctx->xa, ctx->dma_xa);
 		ctx->xa = NULL;
 	}
 	if (ctx->p) {
+		memset(ctx->p, 0, ctx->p_size);
 		dma_free_coherent(dev, ctx->p_size, ctx->p, ctx->dma_p);
 		ctx->p = NULL;
 	}
@@ -480,11 +488,13 @@
 {
 	struct qat_dh_ctx *ctx = kpp_tfm_ctx(tfm);
 	struct qat_crypto_instance *inst =
-			qat_crypto_get_instance_node(get_current_node());
+			qat_crypto_get_instance_node(numa_node_id());
 
 	if (!inst)
 		return -EINVAL;
 
+	kpp_set_reqsize(tfm, sizeof(struct qat_asym_request) + 64);
+
 	ctx->p_size = 0;
 	ctx->g2 = false;
 	ctx->inst = inst;
@@ -510,23 +520,19 @@
 
 	err = (err == ICP_QAT_FW_COMN_STATUS_FLAG_OK) ? 0 : -EINVAL;
 
-	if (req->src_align)
-		dma_free_coherent(dev, req->ctx.rsa->key_sz, req->src_align,
-				  req->in.rsa.enc.m);
-	else
-		dma_unmap_single(dev, req->in.rsa.enc.m, req->ctx.rsa->key_sz,
-				 DMA_TO_DEVICE);
+	dma_unmap_single(dev, req->in.rsa.enc.m, req->ctx.rsa->key_sz,
+			 DMA_TO_DEVICE);
+
+	kfree_sensitive(req->src_align);
 
 	areq->dst_len = req->ctx.rsa->key_sz;
+	dma_unmap_single(dev, req->out.rsa.enc.c, req->ctx.rsa->key_sz,
+			 DMA_FROM_DEVICE);
 	if (req->dst_align) {
 		scatterwalk_map_and_copy(req->dst_align, areq->dst, 0,
 					 areq->dst_len, 1);
 
-		dma_free_coherent(dev, req->ctx.rsa->key_sz, req->dst_align,
-				  req->out.rsa.enc.c);
-	} else {
-		dma_unmap_single(dev, req->out.rsa.enc.c, req->ctx.rsa->key_sz,
-				 DMA_FROM_DEVICE);
+		kfree_sensitive(req->dst_align);
 	}
 
 	dma_unmap_single(dev, req->phy_in, sizeof(struct qat_rsa_input_params),
@@ -542,8 +548,11 @@
 {
 	struct icp_qat_fw_pke_resp *resp = _resp;
 	struct qat_asym_request *areq = (void *)(__force long)resp->opaque;
+	struct qat_instance_backlog *backlog = areq->alg_req.backlog;
 
 	areq->cb(resp);
+
+	qat_alg_send_backlog(backlog);
 }
 
 #define PKE_RSA_EP_512 0x1c161b21
@@ -642,7 +651,9 @@
 	struct qat_asym_request *qat_req =
 			PTR_ALIGN(akcipher_request_ctx(req), 64);
 	struct icp_qat_fw_pke_request *msg = &qat_req->req;
-	int ret, ctr = 0;
+	gfp_t flags = qat_algs_alloc_flags(&req->base);
+	u8 *vaddr;
+	int ret;
 
 	if (unlikely(!ctx->n || !ctx->e))
 		return -EINVAL;
@@ -651,6 +662,10 @@
 		req->dst_len = ctx->key_sz;
 		return -EOVERFLOW;
 	}
+
+	if (req->src_len > ctx->key_sz)
+		return -EINVAL;
+
 	memset(msg, '\0', sizeof(*msg));
 	ICP_QAT_FW_PKE_HDR_VALID_FLAG_SET(msg->pke_hdr,
 					  ICP_QAT_FW_COMN_REQ_FLAG_SET);
@@ -679,50 +694,49 @@
 	 */
 	if (sg_is_last(req->src) && req->src_len == ctx->key_sz) {
 		qat_req->src_align = NULL;
-		qat_req->in.rsa.enc.m = dma_map_single(dev, sg_virt(req->src),
-						   req->src_len, DMA_TO_DEVICE);
-		if (unlikely(dma_mapping_error(dev, qat_req->in.rsa.enc.m)))
-			return ret;
-
+		vaddr = sg_virt(req->src);
 	} else {
 		int shift = ctx->key_sz - req->src_len;
 
-		qat_req->src_align = dma_alloc_coherent(dev, ctx->key_sz,
-							&qat_req->in.rsa.enc.m,
-							GFP_KERNEL);
+		qat_req->src_align = kzalloc(ctx->key_sz, flags);
 		if (unlikely(!qat_req->src_align))
 			return ret;
 
 		scatterwalk_map_and_copy(qat_req->src_align + shift, req->src,
 					 0, req->src_len, 0);
+		vaddr = qat_req->src_align;
 	}
-	if (sg_is_last(req->dst) && req->dst_len == ctx->key_sz) {
-		qat_req->dst_align = NULL;
-		qat_req->out.rsa.enc.c = dma_map_single(dev, sg_virt(req->dst),
-							req->dst_len,
-							DMA_FROM_DEVICE);
 
-		if (unlikely(dma_mapping_error(dev, qat_req->out.rsa.enc.c)))
-			goto unmap_src;
+	qat_req->in.rsa.enc.m = dma_map_single(dev, vaddr, ctx->key_sz,
+					       DMA_TO_DEVICE);
+	if (unlikely(dma_mapping_error(dev, qat_req->in.rsa.enc.m)))
+		goto unmap_src;
 
+	if (sg_is_last(req->dst) && req->dst_len == ctx->key_sz) {
+		qat_req->dst_align = NULL;
+		vaddr = sg_virt(req->dst);
 	} else {
-		qat_req->dst_align = dma_alloc_coherent(dev, ctx->key_sz,
-							&qat_req->out.rsa.enc.c,
-							GFP_KERNEL);
+		qat_req->dst_align = kzalloc(ctx->key_sz, flags);
 		if (unlikely(!qat_req->dst_align))
 			goto unmap_src;
-
+		vaddr = qat_req->dst_align;
 	}
+
+	qat_req->out.rsa.enc.c = dma_map_single(dev, vaddr, ctx->key_sz,
+						DMA_FROM_DEVICE);
+	if (unlikely(dma_mapping_error(dev, qat_req->out.rsa.enc.c)))
+		goto unmap_dst;
+
 	qat_req->in.rsa.in_tab[3] = 0;
 	qat_req->out.rsa.out_tab[1] = 0;
-	qat_req->phy_in = dma_map_single(dev, &qat_req->in.rsa.enc.m,
-					 sizeof(qat_req->in.rsa.enc.m),
+	qat_req->phy_in = dma_map_single(dev, &qat_req->in.rsa,
+					 sizeof(struct qat_rsa_input_params),
 					 DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, qat_req->phy_in)))
 		goto unmap_dst;
 
-	qat_req->phy_out = dma_map_single(dev, &qat_req->out.rsa.enc.c,
-					  sizeof(qat_req->out.rsa.enc.c),
+	qat_req->phy_out = dma_map_single(dev, &qat_req->out.rsa,
+					  sizeof(struct qat_rsa_output_params),
 					  DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, qat_req->phy_out)))
 		goto unmap_in_params;
@@ -732,13 +746,14 @@
 	msg->pke_mid.opaque = (u64)(__force long)qat_req;
 	msg->input_param_count = 3;
 	msg->output_param_count = 1;
-	do {
-		ret = adf_send_message(ctx->inst->pke_tx, (u32 *)msg);
-	} while (ret == -EBUSY && ctr++ < 100);
 
-	if (!ret)
-		return -EINPROGRESS;
+	ret = qat_alg_send_asym_message(qat_req, inst, &req->base);
+	if (ret == -ENOSPC)
+		goto unmap_all;
 
+	return ret;
+
+unmap_all:
 	if (!dma_mapping_error(dev, qat_req->phy_out))
 		dma_unmap_single(dev, qat_req->phy_out,
 				 sizeof(struct qat_rsa_output_params),
@@ -749,21 +764,15 @@
 				 sizeof(struct qat_rsa_input_params),
 				 DMA_TO_DEVICE);
 unmap_dst:
-	if (qat_req->dst_align)
-		dma_free_coherent(dev, ctx->key_sz, qat_req->dst_align,
-				  qat_req->out.rsa.enc.c);
-	else
-		if (!dma_mapping_error(dev, qat_req->out.rsa.enc.c))
-			dma_unmap_single(dev, qat_req->out.rsa.enc.c,
-					 ctx->key_sz, DMA_FROM_DEVICE);
+	if (!dma_mapping_error(dev, qat_req->out.rsa.enc.c))
+		dma_unmap_single(dev, qat_req->out.rsa.enc.c,
+				 ctx->key_sz, DMA_FROM_DEVICE);
+	kfree_sensitive(qat_req->dst_align);
 unmap_src:
-	if (qat_req->src_align)
-		dma_free_coherent(dev, ctx->key_sz, qat_req->src_align,
-				  qat_req->in.rsa.enc.m);
-	else
-		if (!dma_mapping_error(dev, qat_req->in.rsa.enc.m))
-			dma_unmap_single(dev, qat_req->in.rsa.enc.m,
-					 ctx->key_sz, DMA_TO_DEVICE);
+	if (!dma_mapping_error(dev, qat_req->in.rsa.enc.m))
+		dma_unmap_single(dev, qat_req->in.rsa.enc.m, ctx->key_sz,
+				 DMA_TO_DEVICE);
+	kfree_sensitive(qat_req->src_align);
 	return ret;
 }
 
@@ -776,7 +785,9 @@
 	struct qat_asym_request *qat_req =
 			PTR_ALIGN(akcipher_request_ctx(req), 64);
 	struct icp_qat_fw_pke_request *msg = &qat_req->req;
-	int ret, ctr = 0;
+	gfp_t flags = qat_algs_alloc_flags(&req->base);
+	u8 *vaddr;
+	int ret;
 
 	if (unlikely(!ctx->n || !ctx->d))
 		return -EINVAL;
@@ -785,6 +796,10 @@
 		req->dst_len = ctx->key_sz;
 		return -EOVERFLOW;
 	}
+
+	if (req->src_len > ctx->key_sz)
+		return -EINVAL;
+
 	memset(msg, '\0', sizeof(*msg));
 	ICP_QAT_FW_PKE_HDR_VALID_FLAG_SET(msg->pke_hdr,
 					  ICP_QAT_FW_COMN_REQ_FLAG_SET);
@@ -823,54 +838,51 @@
 	 */
 	if (sg_is_last(req->src) && req->src_len == ctx->key_sz) {
 		qat_req->src_align = NULL;
-		qat_req->in.rsa.dec.c = dma_map_single(dev, sg_virt(req->src),
-						   req->dst_len, DMA_TO_DEVICE);
-		if (unlikely(dma_mapping_error(dev, qat_req->in.rsa.dec.c)))
-			return ret;
-
+		vaddr = sg_virt(req->src);
 	} else {
 		int shift = ctx->key_sz - req->src_len;
 
-		qat_req->src_align = dma_alloc_coherent(dev, ctx->key_sz,
-							&qat_req->in.rsa.dec.c,
-							GFP_KERNEL);
+		qat_req->src_align = kzalloc(ctx->key_sz, flags);
 		if (unlikely(!qat_req->src_align))
 			return ret;
 
 		scatterwalk_map_and_copy(qat_req->src_align + shift, req->src,
 					 0, req->src_len, 0);
+		vaddr = qat_req->src_align;
 	}
-	if (sg_is_last(req->dst) && req->dst_len == ctx->key_sz) {
-		qat_req->dst_align = NULL;
-		qat_req->out.rsa.dec.m = dma_map_single(dev, sg_virt(req->dst),
-						    req->dst_len,
-						    DMA_FROM_DEVICE);
 
-		if (unlikely(dma_mapping_error(dev, qat_req->out.rsa.dec.m)))
-			goto unmap_src;
+	qat_req->in.rsa.dec.c = dma_map_single(dev, vaddr, ctx->key_sz,
+					       DMA_TO_DEVICE);
+	if (unlikely(dma_mapping_error(dev, qat_req->in.rsa.dec.c)))
+		goto unmap_src;
 
+	if (sg_is_last(req->dst) && req->dst_len == ctx->key_sz) {
+		qat_req->dst_align = NULL;
+		vaddr = sg_virt(req->dst);
 	} else {
-		qat_req->dst_align = dma_alloc_coherent(dev, ctx->key_sz,
-							&qat_req->out.rsa.dec.m,
-							GFP_KERNEL);
+		qat_req->dst_align = kzalloc(ctx->key_sz, flags);
 		if (unlikely(!qat_req->dst_align))
 			goto unmap_src;
-
+		vaddr = qat_req->dst_align;
 	}
+	qat_req->out.rsa.dec.m = dma_map_single(dev, vaddr, ctx->key_sz,
+						DMA_FROM_DEVICE);
+	if (unlikely(dma_mapping_error(dev, qat_req->out.rsa.dec.m)))
+		goto unmap_dst;
 
 	if (ctx->crt_mode)
 		qat_req->in.rsa.in_tab[6] = 0;
 	else
 		qat_req->in.rsa.in_tab[3] = 0;
 	qat_req->out.rsa.out_tab[1] = 0;
-	qat_req->phy_in = dma_map_single(dev, &qat_req->in.rsa.dec.c,
-					 sizeof(qat_req->in.rsa.dec.c),
+	qat_req->phy_in = dma_map_single(dev, &qat_req->in.rsa,
+					 sizeof(struct qat_rsa_input_params),
 					 DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, qat_req->phy_in)))
 		goto unmap_dst;
 
-	qat_req->phy_out = dma_map_single(dev, &qat_req->out.rsa.dec.m,
-					  sizeof(qat_req->out.rsa.dec.m),
+	qat_req->phy_out = dma_map_single(dev, &qat_req->out.rsa,
+					  sizeof(struct qat_rsa_output_params),
 					  DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, qat_req->phy_out)))
 		goto unmap_in_params;
@@ -884,13 +896,14 @@
 		msg->input_param_count = 3;
 
 	msg->output_param_count = 1;
-	do {
-		ret = adf_send_message(ctx->inst->pke_tx, (u32 *)msg);
-	} while (ret == -EBUSY && ctr++ < 100);
 
-	if (!ret)
-		return -EINPROGRESS;
+	ret = qat_alg_send_asym_message(qat_req, inst, &req->base);
+	if (ret == -ENOSPC)
+		goto unmap_all;
 
+	return ret;
+
+unmap_all:
 	if (!dma_mapping_error(dev, qat_req->phy_out))
 		dma_unmap_single(dev, qat_req->phy_out,
 				 sizeof(struct qat_rsa_output_params),
@@ -901,21 +914,15 @@
 				 sizeof(struct qat_rsa_input_params),
 				 DMA_TO_DEVICE);
 unmap_dst:
-	if (qat_req->dst_align)
-		dma_free_coherent(dev, ctx->key_sz, qat_req->dst_align,
-				  qat_req->out.rsa.dec.m);
-	else
-		if (!dma_mapping_error(dev, qat_req->out.rsa.dec.m))
-			dma_unmap_single(dev, qat_req->out.rsa.dec.m,
-					 ctx->key_sz, DMA_FROM_DEVICE);
+	if (!dma_mapping_error(dev, qat_req->out.rsa.dec.m))
+		dma_unmap_single(dev, qat_req->out.rsa.dec.m,
+				 ctx->key_sz, DMA_FROM_DEVICE);
+	kfree_sensitive(qat_req->dst_align);
 unmap_src:
-	if (qat_req->src_align)
-		dma_free_coherent(dev, ctx->key_sz, qat_req->src_align,
-				  qat_req->in.rsa.dec.c);
-	else
-		if (!dma_mapping_error(dev, qat_req->in.rsa.dec.c))
-			dma_unmap_single(dev, qat_req->in.rsa.dec.c,
-					 ctx->key_sz, DMA_TO_DEVICE);
+	if (!dma_mapping_error(dev, qat_req->in.rsa.dec.c))
+		dma_unmap_single(dev, qat_req->in.rsa.dec.c, ctx->key_sz,
+				 DMA_TO_DEVICE);
+	kfree_sensitive(qat_req->src_align);
 	return ret;
 }
 
@@ -1218,11 +1225,13 @@
 {
 	struct qat_rsa_ctx *ctx = akcipher_tfm_ctx(tfm);
 	struct qat_crypto_instance *inst =
-			qat_crypto_get_instance_node(get_current_node());
+			qat_crypto_get_instance_node(numa_node_id());
 
 	if (!inst)
 		return -EINVAL;
 
+	akcipher_set_reqsize(tfm, sizeof(struct qat_asym_request) + 64);
+
 	ctx->key_sz = 0;
 	ctx->inst = inst;
 	return 0;
@@ -1233,18 +1242,8 @@
 	struct qat_rsa_ctx *ctx = akcipher_tfm_ctx(tfm);
 	struct device *dev = &GET_DEV(ctx->inst->accel_dev);
 
-	if (ctx->n)
-		dma_free_coherent(dev, ctx->key_sz, ctx->n, ctx->dma_n);
-	if (ctx->e)
-		dma_free_coherent(dev, ctx->key_sz, ctx->e, ctx->dma_e);
-	if (ctx->d) {
-		memset(ctx->d, '\0', ctx->key_sz);
-		dma_free_coherent(dev, ctx->key_sz, ctx->d, ctx->dma_d);
-	}
+	qat_rsa_clear_ctx(dev, ctx);
 	qat_crypto_put_instance(ctx->inst);
-	ctx->n = NULL;
-	ctx->e = NULL;
-	ctx->d = NULL;
 }
 
 static struct akcipher_alg rsa = {
@@ -1255,7 +1254,6 @@
 	.max_size = qat_rsa_max_size,
 	.init = qat_rsa_init_tfm,
 	.exit = qat_rsa_exit_tfm,
-	.reqsize = sizeof(struct qat_asym_request) + 64,
 	.base = {
 		.cra_name = "rsa",
 		.cra_driver_name = "qat-rsa",
@@ -1272,7 +1270,6 @@
 	.max_size = qat_dh_max_size,
 	.init = qat_dh_init_tfm,
 	.exit = qat_dh_exit_tfm,
-	.reqsize = sizeof(struct qat_asym_request) + 64,
 	.base = {
 		.cra_name = "dh",
 		.cra_driver_name = "qat-dh",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/qat_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/qat_crypto.c
@@ -321,6 +321,9 @@
 				      &inst->pke_rx);
 		if (ret)
 			goto err;
+
+		INIT_LIST_HEAD(&inst->backlog.list);
+		spin_lock_init(&inst->backlog.lock);
 	}
 	return 0;
 err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_common/qat_crypto.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_common/qat_crypto.h
@@ -9,6 +9,19 @@
 #include "adf_accel_devices.h"
 #include "icp_qat_fw_la.h"
 
+struct qat_instance_backlog {
+	struct list_head list;
+	spinlock_t lock; /* protects backlog list */
+};
+
+struct qat_alg_req {
+	u32 *fw_req;
+	struct adf_etr_ring_data *tx_ring;
+	struct crypto_async_request *base;
+	struct list_head list;
+	struct qat_instance_backlog *backlog;
+};
+
 struct qat_crypto_instance {
 	struct adf_etr_ring_data *sym_tx;
 	struct adf_etr_ring_data *sym_rx;
@@ -19,8 +32,29 @@
 	unsigned long state;
 	int id;
 	atomic_t refctr;
+	struct qat_instance_backlog backlog;
 };
 
+#define QAT_MAX_BUFF_DESC	4
+
+struct qat_alg_buf {
+	u32 len;
+	u32 resrvd;
+	u64 addr;
+} __packed;
+
+struct qat_alg_buf_list {
+	u64 resrvd;
+	u32 num_bufs;
+	u32 num_mapped_bufs;
+	struct qat_alg_buf bufers[];
+} __packed;
+
+struct qat_alg_fixed_buf_list {
+	struct qat_alg_buf_list sgl_hdr;
+	struct qat_alg_buf descriptors[QAT_MAX_BUFF_DESC];
+} __packed __aligned(64);
+
 struct qat_crypto_request_buffs {
 	struct qat_alg_buf_list *bl;
 	dma_addr_t blp;
@@ -28,6 +62,10 @@
 	dma_addr_t bloutp;
 	size_t sz;
 	size_t sz_out;
+	bool sgl_src_valid;
+	bool sgl_dst_valid;
+	struct qat_alg_fixed_buf_list sgl_src;
+	struct qat_alg_fixed_buf_list sgl_dst;
 };
 
 struct qat_crypto_request;
@@ -53,6 +91,7 @@
 		u8 iv[AES_BLOCK_SIZE];
 	};
 	bool encryption;
+	struct qat_alg_req alg_req;
 };
 
 static inline bool adf_hw_dev_has_crypto(struct adf_accel_dev *accel_dev)
@@ -70,4 +109,9 @@
 	return true;
 }
 
+static inline gfp_t qat_algs_alloc_flags(struct crypto_async_request *req)
+{
+	return req->flags & CRYPTO_TFM_REQ_MAY_SLEEP ? GFP_KERNEL : GFP_ATOMIC;
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qat/qat_dh895xcc/adf_dh895xcc_hw_data.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qat/qat_dh895xcc/adf_dh895xcc_hw_data.c
@@ -86,17 +86,26 @@
 
 	capabilities = ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC |
 		       ICP_ACCEL_CAPABILITIES_CRYPTO_ASYMMETRIC |
-		       ICP_ACCEL_CAPABILITIES_AUTHENTICATION;
+		       ICP_ACCEL_CAPABILITIES_AUTHENTICATION |
+		       ICP_ACCEL_CAPABILITIES_CIPHER |
+		       ICP_ACCEL_CAPABILITIES_COMPRESSION;
 
 	/* Read accelerator capabilities mask */
 	pci_read_config_dword(pdev, ADF_DEVICE_LEGFUSE_OFFSET, &legfuses);
 
-	if (legfuses & ICP_ACCEL_MASK_CIPHER_SLICE)
+	/* A set bit in legfuses means the feature is OFF in this SKU */
+	if (legfuses & ICP_ACCEL_MASK_CIPHER_SLICE) {
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC;
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_CIPHER;
+	}
 	if (legfuses & ICP_ACCEL_MASK_PKE_SLICE)
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_CRYPTO_ASYMMETRIC;
-	if (legfuses & ICP_ACCEL_MASK_AUTH_SLICE)
+	if (legfuses & ICP_ACCEL_MASK_AUTH_SLICE) {
 		capabilities &= ~ICP_ACCEL_CAPABILITIES_AUTHENTICATION;
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_CIPHER;
+	}
+	if (legfuses & ICP_ACCEL_MASK_COMPRESS_SLICE)
+		capabilities &= ~ICP_ACCEL_CAPABILITIES_COMPRESSION;
 
 	return capabilities;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qce/aead.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qce/aead.c
@@ -786,7 +786,7 @@
 	alg->init			= qce_aead_init;
 	alg->exit			= qce_aead_exit;
 
-	alg->base.cra_priority		= 300;
+	alg->base.cra_priority		= 275;
 	alg->base.cra_flags		= CRYPTO_ALG_ASYNC |
 					  CRYPTO_ALG_ALLOCATES_MEMORY |
 					  CRYPTO_ALG_KERN_DRIVER_ONLY |
@@ -802,8 +802,8 @@
 
 	ret = crypto_register_aead(alg);
 	if (ret) {
-		kfree(tmpl);
 		dev_err(qce->dev, "%s registration failed\n", alg->base.cra_name);
+		kfree(tmpl);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qce/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qce/core.c
@@ -48,16 +48,19 @@
 static int qce_register_algs(struct qce_device *qce)
 {
 	const struct qce_algo_ops *ops;
-	int i, ret = -ENODEV;
+	int i, j, ret = -ENODEV;
 
 	for (i = 0; i < ARRAY_SIZE(qce_ops); i++) {
 		ops = qce_ops[i];
 		ret = ops->register_algs(qce);
-		if (ret)
-			break;
+		if (ret) {
+			for (j = i - 1; j >= 0; j--)
+				ops->unregister_algs(qce);
+			return ret;
+		}
 	}
 
-	return ret;
+	return 0;
 }
 
 static int qce_handle_request(struct crypto_async_request *async_req)
@@ -236,7 +239,7 @@
 
 	ret = qce_check_version(qce);
 	if (ret)
-		goto err_clks;
+		goto err_dma;
 
 	spin_lock_init(&qce->lock);
 	tasklet_init(&qce->done_tasklet, qce_tasklet_req_done,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qce/sha.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qce/sha.c
@@ -480,7 +480,7 @@
 
 	base = &alg->halg.base;
 	base->cra_blocksize = def->blocksize;
-	base->cra_priority = 300;
+	base->cra_priority = 175;
 	base->cra_flags = CRYPTO_ALG_ASYNC | CRYPTO_ALG_KERN_DRIVER_ONLY;
 	base->cra_ctxsize = sizeof(struct qce_sha_ctx);
 	base->cra_alignmask = 0;
@@ -498,8 +498,8 @@
 
 	ret = crypto_register_ahash(alg);
 	if (ret) {
-		kfree(tmpl);
 		dev_err(qce->dev, "%s registration failed\n", base->cra_name);
+		kfree(tmpl);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qce/skcipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qce/skcipher.c
@@ -461,7 +461,7 @@
 	alg->encrypt			= qce_skcipher_encrypt;
 	alg->decrypt			= qce_skcipher_decrypt;
 
-	alg->base.cra_priority		= 300;
+	alg->base.cra_priority		= 275;
 	alg->base.cra_flags		= CRYPTO_ALG_ASYNC |
 					  CRYPTO_ALG_ALLOCATES_MEMORY |
 					  CRYPTO_ALG_KERN_DRIVER_ONLY;
@@ -484,8 +484,8 @@
 
 	ret = crypto_register_skcipher(alg);
 	if (ret) {
-		kfree(tmpl);
 		dev_err(qce->dev, "%s registration failed\n", alg->base.cra_name);
+		kfree(tmpl);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/qcom-rng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/qcom-rng.c
@@ -8,6 +8,7 @@
 #include <linux/clk.h>
 #include <linux/crypto.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
@@ -43,16 +44,19 @@
 {
 	unsigned int currsize = 0;
 	u32 val;
+	int ret;
 
 	/* read random data from hardware */
 	do {
-		val = readl_relaxed(rng->base + PRNG_STATUS);
-		if (!(val & PRNG_STATUS_DATA_AVAIL))
-			break;
+		ret = readl_poll_timeout(rng->base + PRNG_STATUS, val,
+					 val & PRNG_STATUS_DATA_AVAIL,
+					 200, 10000);
+		if (ret)
+			return ret;
 
 		val = readl_relaxed(rng->base + PRNG_DATA_OUT);
 		if (!val)
-			break;
+			return -EINVAL;
 
 		if ((max - currsize) >= WORD_SZ) {
 			memcpy(data, &val, WORD_SZ);
@@ -65,7 +69,7 @@
 		}
 	} while (currsize < max);
 
-	return currsize;
+	return 0;
 }
 
 static int qcom_rng_generate(struct crypto_rng *tfm,
@@ -87,7 +91,7 @@
 	mutex_unlock(&rng->lock);
 	clk_disable_unprepare(rng->clk);
 
-	return 0;
+	return ret;
 }
 
 static int qcom_rng_seed(struct crypto_rng *tfm, const u8 *seed,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/rockchip/rk3288_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/rockchip/rk3288_crypto.c
@@ -65,186 +65,24 @@
 	clk_disable_unprepare(dev->sclk);
 }
 
-static int check_alignment(struct scatterlist *sg_src,
-			   struct scatterlist *sg_dst,
-			   int align_mask)
-{
-	int in, out, align;
-
-	in = IS_ALIGNED((uint32_t)sg_src->offset, 4) &&
-	     IS_ALIGNED((uint32_t)sg_src->length, align_mask);
-	if (!sg_dst)
-		return in;
-	out = IS_ALIGNED((uint32_t)sg_dst->offset, 4) &&
-	      IS_ALIGNED((uint32_t)sg_dst->length, align_mask);
-	align = in && out;
-
-	return (align && (sg_src->length == sg_dst->length));
-}
-
-static int rk_load_data(struct rk_crypto_info *dev,
-			struct scatterlist *sg_src,
-			struct scatterlist *sg_dst)
-{
-	unsigned int count;
-
-	dev->aligned = dev->aligned ?
-		check_alignment(sg_src, sg_dst, dev->align_size) :
-		dev->aligned;
-	if (dev->aligned) {
-		count = min(dev->left_bytes, sg_src->length);
-		dev->left_bytes -= count;
-
-		if (!dma_map_sg(dev->dev, sg_src, 1, DMA_TO_DEVICE)) {
-			dev_err(dev->dev, "[%s:%d] dma_map_sg(src)  error\n",
-				__func__, __LINE__);
-			return -EINVAL;
-		}
-		dev->addr_in = sg_dma_address(sg_src);
-
-		if (sg_dst) {
-			if (!dma_map_sg(dev->dev, sg_dst, 1, DMA_FROM_DEVICE)) {
-				dev_err(dev->dev,
-					"[%s:%d] dma_map_sg(dst)  error\n",
-					__func__, __LINE__);
-				dma_unmap_sg(dev->dev, sg_src, 1,
-					     DMA_TO_DEVICE);
-				return -EINVAL;
-			}
-			dev->addr_out = sg_dma_address(sg_dst);
-		}
-	} else {
-		count = (dev->left_bytes > PAGE_SIZE) ?
-			PAGE_SIZE : dev->left_bytes;
-
-		if (!sg_pcopy_to_buffer(dev->first, dev->src_nents,
-					dev->addr_vir, count,
-					dev->total - dev->left_bytes)) {
-			dev_err(dev->dev, "[%s:%d] pcopy err\n",
-				__func__, __LINE__);
-			return -EINVAL;
-		}
-		dev->left_bytes -= count;
-		sg_init_one(&dev->sg_tmp, dev->addr_vir, count);
-		if (!dma_map_sg(dev->dev, &dev->sg_tmp, 1, DMA_TO_DEVICE)) {
-			dev_err(dev->dev, "[%s:%d] dma_map_sg(sg_tmp)  error\n",
-				__func__, __LINE__);
-			return -ENOMEM;
-		}
-		dev->addr_in = sg_dma_address(&dev->sg_tmp);
-
-		if (sg_dst) {
-			if (!dma_map_sg(dev->dev, &dev->sg_tmp, 1,
-					DMA_FROM_DEVICE)) {
-				dev_err(dev->dev,
-					"[%s:%d] dma_map_sg(sg_tmp)  error\n",
-					__func__, __LINE__);
-				dma_unmap_sg(dev->dev, &dev->sg_tmp, 1,
-					     DMA_TO_DEVICE);
-				return -ENOMEM;
-			}
-			dev->addr_out = sg_dma_address(&dev->sg_tmp);
-		}
-	}
-	dev->count = count;
-	return 0;
-}
-
-static void rk_unload_data(struct rk_crypto_info *dev)
-{
-	struct scatterlist *sg_in, *sg_out;
-
-	sg_in = dev->aligned ? dev->sg_src : &dev->sg_tmp;
-	dma_unmap_sg(dev->dev, sg_in, 1, DMA_TO_DEVICE);
-
-	if (dev->sg_dst) {
-		sg_out = dev->aligned ? dev->sg_dst : &dev->sg_tmp;
-		dma_unmap_sg(dev->dev, sg_out, 1, DMA_FROM_DEVICE);
-	}
-}
-
 static irqreturn_t rk_crypto_irq_handle(int irq, void *dev_id)
 {
 	struct rk_crypto_info *dev  = platform_get_drvdata(dev_id);
 	u32 interrupt_status;
 
-	spin_lock(&dev->lock);
 	interrupt_status = CRYPTO_READ(dev, RK_CRYPTO_INTSTS);
 	CRYPTO_WRITE(dev, RK_CRYPTO_INTSTS, interrupt_status);
 
+	dev->status = 1;
 	if (interrupt_status & 0x0a) {
 		dev_warn(dev->dev, "DMA Error\n");
-		dev->err = -EFAULT;
+		dev->status = 0;
 	}
-	tasklet_schedule(&dev->done_task);
+	complete(&dev->complete);
 
-	spin_unlock(&dev->lock);
 	return IRQ_HANDLED;
 }
 
-static int rk_crypto_enqueue(struct rk_crypto_info *dev,
-			      struct crypto_async_request *async_req)
-{
-	unsigned long flags;
-	int ret;
-
-	spin_lock_irqsave(&dev->lock, flags);
-	ret = crypto_enqueue_request(&dev->queue, async_req);
-	if (dev->busy) {
-		spin_unlock_irqrestore(&dev->lock, flags);
-		return ret;
-	}
-	dev->busy = true;
-	spin_unlock_irqrestore(&dev->lock, flags);
-	tasklet_schedule(&dev->queue_task);
-
-	return ret;
-}
-
-static void rk_crypto_queue_task_cb(unsigned long data)
-{
-	struct rk_crypto_info *dev = (struct rk_crypto_info *)data;
-	struct crypto_async_request *async_req, *backlog;
-	unsigned long flags;
-	int err = 0;
-
-	dev->err = 0;
-	spin_lock_irqsave(&dev->lock, flags);
-	backlog   = crypto_get_backlog(&dev->queue);
-	async_req = crypto_dequeue_request(&dev->queue);
-
-	if (!async_req) {
-		dev->busy = false;
-		spin_unlock_irqrestore(&dev->lock, flags);
-		return;
-	}
-	spin_unlock_irqrestore(&dev->lock, flags);
-
-	if (backlog) {
-		backlog->complete(backlog, -EINPROGRESS);
-		backlog = NULL;
-	}
-
-	dev->async_req = async_req;
-	err = dev->start(dev);
-	if (err)
-		dev->complete(dev->async_req, err);
-}
-
-static void rk_crypto_done_task_cb(unsigned long data)
-{
-	struct rk_crypto_info *dev = (struct rk_crypto_info *)data;
-
-	if (dev->err) {
-		dev->complete(dev->async_req, dev->err);
-		return;
-	}
-
-	dev->err = dev->update(dev);
-	if (dev->err)
-		dev->complete(dev->async_req, dev->err);
-}
-
 static struct rk_crypto_tmp *rk_cipher_algs[] = {
 	&rk_ecb_aes_alg,
 	&rk_cbc_aes_alg,
@@ -337,8 +175,6 @@
 	if (err)
 		goto err_crypto;
 
-	spin_lock_init(&crypto_info->lock);
-
 	crypto_info->reg = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(crypto_info->reg)) {
 		err = PTR_ERR(crypto_info->reg);
@@ -389,18 +225,11 @@
 	crypto_info->dev = &pdev->dev;
 	platform_set_drvdata(pdev, crypto_info);
 
-	tasklet_init(&crypto_info->queue_task,
-		     rk_crypto_queue_task_cb, (unsigned long)crypto_info);
-	tasklet_init(&crypto_info->done_task,
-		     rk_crypto_done_task_cb, (unsigned long)crypto_info);
-	crypto_init_queue(&crypto_info->queue, 50);
-
-	crypto_info->enable_clk = rk_crypto_enable_clk;
-	crypto_info->disable_clk = rk_crypto_disable_clk;
-	crypto_info->load_data = rk_load_data;
-	crypto_info->unload_data = rk_unload_data;
-	crypto_info->enqueue = rk_crypto_enqueue;
-	crypto_info->busy = false;
+	crypto_info->engine = crypto_engine_alloc_init(&pdev->dev, true);
+	crypto_engine_start(crypto_info->engine);
+	init_completion(&crypto_info->complete);
+
+	rk_crypto_enable_clk(crypto_info);
 
 	err = rk_crypto_register(crypto_info);
 	if (err) {
@@ -412,9 +241,9 @@
 	return 0;
 
 err_register_alg:
-	tasklet_kill(&crypto_info->queue_task);
-	tasklet_kill(&crypto_info->done_task);
+	crypto_engine_exit(crypto_info->engine);
 err_crypto:
+	dev_err(dev, "Crypto Accelerator not successfully registered\n");
 	return err;
 }
 
@@ -423,8 +252,8 @@
 	struct rk_crypto_info *crypto_tmp = platform_get_drvdata(pdev);
 
 	rk_crypto_unregister();
-	tasklet_kill(&crypto_tmp->done_task);
-	tasklet_kill(&crypto_tmp->queue_task);
+	rk_crypto_disable_clk(crypto_tmp);
+	crypto_engine_exit(crypto_tmp->engine);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/rockchip/rk3288_crypto.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/rockchip/rk3288_crypto.h
@@ -5,9 +5,11 @@
 #include <crypto/aes.h>
 #include <crypto/internal/des.h>
 #include <crypto/algapi.h>
+#include <linux/dma-mapping.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/scatterlist.h>
+#include <crypto/engine.h>
 #include <crypto/internal/hash.h>
 #include <crypto/internal/skcipher.h>
 
@@ -193,45 +195,15 @@
 	struct reset_control		*rst;
 	void __iomem			*reg;
 	int				irq;
-	struct crypto_queue		queue;
-	struct tasklet_struct		queue_task;
-	struct tasklet_struct		done_task;
-	struct crypto_async_request	*async_req;
-	int 				err;
-	/* device lock */
-	spinlock_t			lock;
-
-	/* the public variable */
-	struct scatterlist		*sg_src;
-	struct scatterlist		*sg_dst;
-	struct scatterlist		sg_tmp;
-	struct scatterlist		*first;
-	unsigned int			left_bytes;
-	void				*addr_vir;
-	int				aligned;
-	int				align_size;
-	size_t				src_nents;
-	size_t				dst_nents;
-	unsigned int			total;
-	unsigned int			count;
-	dma_addr_t			addr_in;
-	dma_addr_t			addr_out;
-	bool				busy;
-	int (*start)(struct rk_crypto_info *dev);
-	int (*update)(struct rk_crypto_info *dev);
-	void (*complete)(struct crypto_async_request *base, int err);
-	int (*enable_clk)(struct rk_crypto_info *dev);
-	void (*disable_clk)(struct rk_crypto_info *dev);
-	int (*load_data)(struct rk_crypto_info *dev,
-			 struct scatterlist *sg_src,
-			 struct scatterlist *sg_dst);
-	void (*unload_data)(struct rk_crypto_info *dev);
-	int (*enqueue)(struct rk_crypto_info *dev,
-		       struct crypto_async_request *async_req);
+
+	struct crypto_engine *engine;
+	struct completion complete;
+	int status;
 };
 
 /* the private variable of hash */
 struct rk_ahash_ctx {
+	struct crypto_engine_ctx enginectx;
 	struct rk_crypto_info		*dev;
 	/* for fallback */
 	struct crypto_ahash		*fallback_tfm;
@@ -241,14 +213,23 @@
 struct rk_ahash_rctx {
 	struct ahash_request		fallback_req;
 	u32				mode;
+	int nrsg;
 };
 
 /* the private variable of cipher */
 struct rk_cipher_ctx {
+	struct crypto_engine_ctx enginectx;
 	struct rk_crypto_info		*dev;
 	unsigned int			keylen;
-	u32				mode;
+	u8				key[AES_MAX_KEY_SIZE];
 	u8				iv[AES_BLOCK_SIZE];
+	struct crypto_skcipher *fallback_tfm;
+};
+
+struct rk_cipher_rctx {
+	u8 backup_iv[AES_BLOCK_SIZE];
+	u32				mode;
+	struct skcipher_request fallback_req;   // keep at the end
 };
 
 enum alg_type {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/rockchip/rk3288_crypto_ahash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/rockchip/rk3288_crypto_ahash.c
@@ -9,6 +9,7 @@
  * Some ideas are from marvell/cesa.c and s5p-sss.c driver.
  */
 #include <linux/device.h>
+#include <asm/unaligned.h>
 #include "rk3288_crypto.h"
 
 /*
@@ -16,6 +17,40 @@
  * so we put the fixed hash out when met zero message.
  */
 
+static bool rk_ahash_need_fallback(struct ahash_request *req)
+{
+	struct scatterlist *sg;
+
+	sg = req->src;
+	while (sg) {
+		if (!IS_ALIGNED(sg->offset, sizeof(u32))) {
+			return true;
+		}
+		if (sg->length % 4) {
+			return true;
+		}
+		sg = sg_next(sg);
+	}
+	return false;
+}
+
+static int rk_ahash_digest_fb(struct ahash_request *areq)
+{
+	struct rk_ahash_rctx *rctx = ahash_request_ctx(areq);
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	struct rk_ahash_ctx *tfmctx = crypto_ahash_ctx(tfm);
+
+	ahash_request_set_tfm(&rctx->fallback_req, tfmctx->fallback_tfm);
+	rctx->fallback_req.base.flags = areq->base.flags &
+					CRYPTO_TFM_REQ_MAY_SLEEP;
+
+	rctx->fallback_req.nbytes = areq->nbytes;
+	rctx->fallback_req.src = areq->src;
+	rctx->fallback_req.result = areq->result;
+
+	return crypto_ahash_digest(&rctx->fallback_req);
+}
+
 static int zero_message_process(struct ahash_request *req)
 {
 	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
@@ -38,16 +73,12 @@
 	return 0;
 }
 
-static void rk_ahash_crypto_complete(struct crypto_async_request *base, int err)
-{
-	if (base->complete)
-		base->complete(base, err);
-}
-
-static void rk_ahash_reg_init(struct rk_crypto_info *dev)
+static void rk_ahash_reg_init(struct ahash_request *req)
 {
-	struct ahash_request *req = ahash_request_cast(dev->async_req);
 	struct rk_ahash_rctx *rctx = ahash_request_ctx(req);
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
+	struct rk_ahash_ctx *tctx = crypto_ahash_ctx(tfm);
+	struct rk_crypto_info *dev = tctx->dev;
 	int reg_status;
 
 	reg_status = CRYPTO_READ(dev, RK_CRYPTO_CTRL) |
@@ -74,7 +105,7 @@
 					  RK_CRYPTO_BYTESWAP_BRFIFO |
 					  RK_CRYPTO_BYTESWAP_BTFIFO);
 
-	CRYPTO_WRITE(dev, RK_CRYPTO_HASH_MSG_LEN, dev->total);
+	CRYPTO_WRITE(dev, RK_CRYPTO_HASH_MSG_LEN, req->nbytes);
 }
 
 static int rk_ahash_init(struct ahash_request *req)
@@ -167,48 +198,64 @@
 	struct rk_ahash_ctx *tctx = crypto_tfm_ctx(req->base.tfm);
 	struct rk_crypto_info *dev = tctx->dev;
 
+	if (rk_ahash_need_fallback(req))
+		return rk_ahash_digest_fb(req);
+
 	if (!req->nbytes)
 		return zero_message_process(req);
-	else
-		return dev->enqueue(dev, &req->base);
+
+	return crypto_transfer_hash_request_to_engine(dev->engine, req);
 }
 
-static void crypto_ahash_dma_start(struct rk_crypto_info *dev)
+static void crypto_ahash_dma_start(struct rk_crypto_info *dev, struct scatterlist *sg)
 {
-	CRYPTO_WRITE(dev, RK_CRYPTO_HRDMAS, dev->addr_in);
-	CRYPTO_WRITE(dev, RK_CRYPTO_HRDMAL, (dev->count + 3) / 4);
+	CRYPTO_WRITE(dev, RK_CRYPTO_HRDMAS, sg_dma_address(sg));
+	CRYPTO_WRITE(dev, RK_CRYPTO_HRDMAL, sg_dma_len(sg) / 4);
 	CRYPTO_WRITE(dev, RK_CRYPTO_CTRL, RK_CRYPTO_HASH_START |
 					  (RK_CRYPTO_HASH_START << 16));
 }
 
-static int rk_ahash_set_data_start(struct rk_crypto_info *dev)
+static int rk_hash_prepare(struct crypto_engine *engine, void *breq)
+{
+	struct ahash_request *areq = container_of(breq, struct ahash_request, base);
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	struct rk_ahash_rctx *rctx = ahash_request_ctx(areq);
+	struct rk_ahash_ctx *tctx = crypto_ahash_ctx(tfm);
+	int ret;
+
+	ret = dma_map_sg(tctx->dev->dev, areq->src, sg_nents(areq->src), DMA_TO_DEVICE);
+	if (ret <= 0)
+		return -EINVAL;
+
+	rctx->nrsg = ret;
+
+	return 0;
+}
+
+static int rk_hash_unprepare(struct crypto_engine *engine, void *breq)
+{
+	struct ahash_request *areq = container_of(breq, struct ahash_request, base);
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	struct rk_ahash_rctx *rctx = ahash_request_ctx(areq);
+	struct rk_ahash_ctx *tctx = crypto_ahash_ctx(tfm);
+
+	dma_unmap_sg(tctx->dev->dev, areq->src, rctx->nrsg, DMA_TO_DEVICE);
+	return 0;
+}
+
+static int rk_hash_run(struct crypto_engine *engine, void *breq)
 {
-	int err;
+	struct ahash_request *areq = container_of(breq, struct ahash_request, base);
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	struct rk_ahash_rctx *rctx = ahash_request_ctx(areq);
+	struct rk_ahash_ctx *tctx = crypto_ahash_ctx(tfm);
+	struct scatterlist *sg = areq->src;
+	int err = 0;
+	int i;
+	u32 v;
 
-	err = dev->load_data(dev, dev->sg_src, NULL);
-	if (!err)
-		crypto_ahash_dma_start(dev);
-	return err;
-}
-
-static int rk_ahash_start(struct rk_crypto_info *dev)
-{
-	struct ahash_request *req = ahash_request_cast(dev->async_req);
-	struct crypto_ahash *tfm;
-	struct rk_ahash_rctx *rctx;
-
-	dev->total = req->nbytes;
-	dev->left_bytes = req->nbytes;
-	dev->aligned = 0;
-	dev->align_size = 4;
-	dev->sg_dst = NULL;
-	dev->sg_src = req->src;
-	dev->first = req->src;
-	dev->src_nents = sg_nents(req->src);
-	rctx = ahash_request_ctx(req);
 	rctx->mode = 0;
 
-	tfm = crypto_ahash_reqtfm(req);
 	switch (crypto_ahash_digestsize(tfm)) {
 	case SHA1_DIGEST_SIZE:
 		rctx->mode = RK_CRYPTO_HASH_SHA1;
@@ -220,32 +267,26 @@
 		rctx->mode = RK_CRYPTO_HASH_MD5;
 		break;
 	default:
-		return -EINVAL;
+		err =  -EINVAL;
+		goto theend;
 	}
 
-	rk_ahash_reg_init(dev);
-	return rk_ahash_set_data_start(dev);
-}
-
-static int rk_ahash_crypto_rx(struct rk_crypto_info *dev)
-{
-	int err = 0;
-	struct ahash_request *req = ahash_request_cast(dev->async_req);
-	struct crypto_ahash *tfm;
+	rk_ahash_reg_init(areq);
 
-	dev->unload_data(dev);
-	if (dev->left_bytes) {
-		if (dev->aligned) {
-			if (sg_is_last(dev->sg_src)) {
-				dev_warn(dev->dev, "[%s:%d], Lack of data\n",
-					 __func__, __LINE__);
-				err = -ENOMEM;
-				goto out_rx;
-			}
-			dev->sg_src = sg_next(dev->sg_src);
+	while (sg) {
+		reinit_completion(&tctx->dev->complete);
+		tctx->dev->status = 0;
+		crypto_ahash_dma_start(tctx->dev, sg);
+		wait_for_completion_interruptible_timeout(&tctx->dev->complete,
+							  msecs_to_jiffies(2000));
+		if (!tctx->dev->status) {
+			dev_err(tctx->dev->dev, "DMA timeout\n");
+			err = -EFAULT;
+			goto theend;
 		}
-		err = rk_ahash_set_data_start(dev);
-	} else {
+		sg = sg_next(sg);
+	}
+
 		/*
 		 * it will take some time to process date after last dma
 		 * transmission.
@@ -256,18 +297,20 @@
 		 * efficiency, and make it response quickly when dma
 		 * complete.
 		 */
-		while (!CRYPTO_READ(dev, RK_CRYPTO_HASH_STS))
-			udelay(10);
+	while (!CRYPTO_READ(tctx->dev, RK_CRYPTO_HASH_STS))
+		udelay(10);
 
-		tfm = crypto_ahash_reqtfm(req);
-		memcpy_fromio(req->result, dev->reg + RK_CRYPTO_HASH_DOUT_0,
-			      crypto_ahash_digestsize(tfm));
-		dev->complete(dev->async_req, 0);
-		tasklet_schedule(&dev->queue_task);
+	for (i = 0; i < crypto_ahash_digestsize(tfm) / 4; i++) {
+		v = readl(tctx->dev->reg + RK_CRYPTO_HASH_DOUT_0 + i * 4);
+		put_unaligned_le32(v, areq->result + i * 4);
 	}
 
-out_rx:
-	return err;
+theend:
+	local_bh_disable();
+	crypto_finalize_hash_request(engine, breq, err);
+	local_bh_enable();
+
+	return 0;
 }
 
 static int rk_cra_hash_init(struct crypto_tfm *tfm)
@@ -281,14 +324,6 @@
 	algt = container_of(alg, struct rk_crypto_tmp, alg.hash);
 
 	tctx->dev = algt->dev;
-	tctx->dev->addr_vir = (void *)__get_free_page(GFP_KERNEL);
-	if (!tctx->dev->addr_vir) {
-		dev_err(tctx->dev->dev, "failed to kmalloc for addr_vir\n");
-		return -ENOMEM;
-	}
-	tctx->dev->start = rk_ahash_start;
-	tctx->dev->update = rk_ahash_crypto_rx;
-	tctx->dev->complete = rk_ahash_crypto_complete;
 
 	/* for fallback */
 	tctx->fallback_tfm = crypto_alloc_ahash(alg_name, 0,
@@ -297,19 +332,23 @@
 		dev_err(tctx->dev->dev, "Could not load fallback driver.\n");
 		return PTR_ERR(tctx->fallback_tfm);
 	}
+
 	crypto_ahash_set_reqsize(__crypto_ahash_cast(tfm),
 				 sizeof(struct rk_ahash_rctx) +
 				 crypto_ahash_reqsize(tctx->fallback_tfm));
 
-	return tctx->dev->enable_clk(tctx->dev);
+	tctx->enginectx.op.do_one_request = rk_hash_run;
+	tctx->enginectx.op.prepare_request = rk_hash_prepare;
+	tctx->enginectx.op.unprepare_request = rk_hash_unprepare;
+
+	return 0;
 }
 
 static void rk_cra_hash_exit(struct crypto_tfm *tfm)
 {
 	struct rk_ahash_ctx *tctx = crypto_tfm_ctx(tfm);
 
-	free_page((unsigned long)tctx->dev->addr_vir);
-	return tctx->dev->disable_clk(tctx->dev);
+	crypto_free_ahash(tctx->fallback_tfm);
 }
 
 struct rk_crypto_tmp rk_ahash_sha1 = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/rockchip/rk3288_crypto_skcipher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/rockchip/rk3288_crypto_skcipher.c
@@ -9,23 +9,77 @@
  * Some ideas are from marvell-cesa.c and s5p-sss.c driver.
  */
 #include <linux/device.h>
+#include <crypto/scatterwalk.h>
 #include "rk3288_crypto.h"
 
 #define RK_CRYPTO_DEC			BIT(0)
 
-static void rk_crypto_complete(struct crypto_async_request *base, int err)
+static int rk_cipher_need_fallback(struct skcipher_request *req)
 {
-	if (base->complete)
-		base->complete(base, err);
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	unsigned int bs = crypto_skcipher_blocksize(tfm);
+	struct scatterlist *sgs, *sgd;
+	unsigned int stodo, dtodo, len;
+
+	if (!req->cryptlen)
+		return true;
+
+	len = req->cryptlen;
+	sgs = req->src;
+	sgd = req->dst;
+	while (sgs && sgd) {
+		if (!IS_ALIGNED(sgs->offset, sizeof(u32))) {
+			return true;
+		}
+		if (!IS_ALIGNED(sgd->offset, sizeof(u32))) {
+			return true;
+		}
+		stodo = min(len, sgs->length);
+		if (stodo % bs) {
+			return true;
+		}
+		dtodo = min(len, sgd->length);
+		if (dtodo % bs) {
+			return true;
+		}
+		if (stodo != dtodo) {
+			return true;
+		}
+		len -= stodo;
+		sgs = sg_next(sgs);
+		sgd = sg_next(sgd);
+	}
+	return false;
+}
+
+static int rk_cipher_fallback(struct skcipher_request *areq)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(areq);
+	struct rk_cipher_ctx *op = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(areq);
+	int err;
+
+	skcipher_request_set_tfm(&rctx->fallback_req, op->fallback_tfm);
+	skcipher_request_set_callback(&rctx->fallback_req, areq->base.flags,
+				      areq->base.complete, areq->base.data);
+	skcipher_request_set_crypt(&rctx->fallback_req, areq->src, areq->dst,
+				   areq->cryptlen, areq->iv);
+	if (rctx->mode & RK_CRYPTO_DEC)
+		err = crypto_skcipher_decrypt(&rctx->fallback_req);
+	else
+		err = crypto_skcipher_encrypt(&rctx->fallback_req);
+	return err;
 }
 
 static int rk_handle_req(struct rk_crypto_info *dev,
 			 struct skcipher_request *req)
 {
-	if (!IS_ALIGNED(req->cryptlen, dev->align_size))
-		return -EINVAL;
-	else
-		return dev->enqueue(dev, &req->base);
+	struct crypto_engine *engine = dev->engine;
+
+	if (rk_cipher_need_fallback(req))
+		return rk_cipher_fallback(req);
+
+	return crypto_transfer_skcipher_request_to_engine(engine, req);
 }
 
 static int rk_aes_setkey(struct crypto_skcipher *cipher,
@@ -38,8 +92,9 @@
 	    keylen != AES_KEYSIZE_256)
 		return -EINVAL;
 	ctx->keylen = keylen;
-	memcpy_toio(ctx->dev->reg + RK_CRYPTO_AES_KEY_0, key, keylen);
-	return 0;
+	memcpy(ctx->key, key, keylen);
+
+	return crypto_skcipher_setkey(ctx->fallback_tfm, key, keylen);
 }
 
 static int rk_des_setkey(struct crypto_skcipher *cipher,
@@ -53,8 +108,9 @@
 		return err;
 
 	ctx->keylen = keylen;
-	memcpy_toio(ctx->dev->reg + RK_CRYPTO_TDES_KEY1_0, key, keylen);
-	return 0;
+	memcpy(ctx->key, key, keylen);
+
+	return crypto_skcipher_setkey(ctx->fallback_tfm, key, keylen);
 }
 
 static int rk_tdes_setkey(struct crypto_skcipher *cipher,
@@ -68,17 +124,19 @@
 		return err;
 
 	ctx->keylen = keylen;
-	memcpy_toio(ctx->dev->reg + RK_CRYPTO_TDES_KEY1_0, key, keylen);
-	return 0;
+	memcpy(ctx->key, key, keylen);
+
+	return crypto_skcipher_setkey(ctx->fallback_tfm, key, keylen);
 }
 
 static int rk_aes_ecb_encrypt(struct skcipher_request *req)
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_AES_ECB_MODE;
+	rctx->mode = RK_CRYPTO_AES_ECB_MODE;
 	return rk_handle_req(dev, req);
 }
 
@@ -86,9 +144,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_AES_ECB_MODE | RK_CRYPTO_DEC;
+	rctx->mode = RK_CRYPTO_AES_ECB_MODE | RK_CRYPTO_DEC;
 	return rk_handle_req(dev, req);
 }
 
@@ -96,9 +155,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_AES_CBC_MODE;
+	rctx->mode = RK_CRYPTO_AES_CBC_MODE;
 	return rk_handle_req(dev, req);
 }
 
@@ -106,9 +166,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_AES_CBC_MODE | RK_CRYPTO_DEC;
+	rctx->mode = RK_CRYPTO_AES_CBC_MODE | RK_CRYPTO_DEC;
 	return rk_handle_req(dev, req);
 }
 
@@ -116,9 +177,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = 0;
+	rctx->mode = 0;
 	return rk_handle_req(dev, req);
 }
 
@@ -126,9 +188,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_DEC;
+	rctx->mode = RK_CRYPTO_DEC;
 	return rk_handle_req(dev, req);
 }
 
@@ -136,9 +199,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_TDES_CHAINMODE_CBC;
+	rctx->mode = RK_CRYPTO_TDES_CHAINMODE_CBC;
 	return rk_handle_req(dev, req);
 }
 
@@ -146,9 +210,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_TDES_CHAINMODE_CBC | RK_CRYPTO_DEC;
+	rctx->mode = RK_CRYPTO_TDES_CHAINMODE_CBC | RK_CRYPTO_DEC;
 	return rk_handle_req(dev, req);
 }
 
@@ -156,9 +221,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_TDES_SELECT;
+	rctx->mode = RK_CRYPTO_TDES_SELECT;
 	return rk_handle_req(dev, req);
 }
 
@@ -166,9 +232,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_TDES_SELECT | RK_CRYPTO_DEC;
+	rctx->mode = RK_CRYPTO_TDES_SELECT | RK_CRYPTO_DEC;
 	return rk_handle_req(dev, req);
 }
 
@@ -176,9 +243,10 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_TDES_SELECT | RK_CRYPTO_TDES_CHAINMODE_CBC;
+	rctx->mode = RK_CRYPTO_TDES_SELECT | RK_CRYPTO_TDES_CHAINMODE_CBC;
 	return rk_handle_req(dev, req);
 }
 
@@ -186,43 +254,42 @@
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_crypto_info *dev = ctx->dev;
 
-	ctx->mode = RK_CRYPTO_TDES_SELECT | RK_CRYPTO_TDES_CHAINMODE_CBC |
+	rctx->mode = RK_CRYPTO_TDES_SELECT | RK_CRYPTO_TDES_CHAINMODE_CBC |
 		    RK_CRYPTO_DEC;
 	return rk_handle_req(dev, req);
 }
 
-static void rk_ablk_hw_init(struct rk_crypto_info *dev)
+static void rk_ablk_hw_init(struct rk_crypto_info *dev, struct skcipher_request *req)
 {
-	struct skcipher_request *req =
-		skcipher_request_cast(dev->async_req);
 	struct crypto_skcipher *cipher = crypto_skcipher_reqtfm(req);
 	struct crypto_tfm *tfm = crypto_skcipher_tfm(cipher);
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(req);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(cipher);
-	u32 ivsize, block, conf_reg = 0;
+	u32 block, conf_reg = 0;
 
 	block = crypto_tfm_alg_blocksize(tfm);
-	ivsize = crypto_skcipher_ivsize(cipher);
 
 	if (block == DES_BLOCK_SIZE) {
-		ctx->mode |= RK_CRYPTO_TDES_FIFO_MODE |
+		rctx->mode |= RK_CRYPTO_TDES_FIFO_MODE |
 			     RK_CRYPTO_TDES_BYTESWAP_KEY |
 			     RK_CRYPTO_TDES_BYTESWAP_IV;
-		CRYPTO_WRITE(dev, RK_CRYPTO_TDES_CTRL, ctx->mode);
-		memcpy_toio(dev->reg + RK_CRYPTO_TDES_IV_0, req->iv, ivsize);
+		CRYPTO_WRITE(dev, RK_CRYPTO_TDES_CTRL, rctx->mode);
+		memcpy_toio(ctx->dev->reg + RK_CRYPTO_TDES_KEY1_0, ctx->key, ctx->keylen);
 		conf_reg = RK_CRYPTO_DESSEL;
 	} else {
-		ctx->mode |= RK_CRYPTO_AES_FIFO_MODE |
+		rctx->mode |= RK_CRYPTO_AES_FIFO_MODE |
 			     RK_CRYPTO_AES_KEY_CHANGE |
 			     RK_CRYPTO_AES_BYTESWAP_KEY |
 			     RK_CRYPTO_AES_BYTESWAP_IV;
 		if (ctx->keylen == AES_KEYSIZE_192)
-			ctx->mode |= RK_CRYPTO_AES_192BIT_key;
+			rctx->mode |= RK_CRYPTO_AES_192BIT_key;
 		else if (ctx->keylen == AES_KEYSIZE_256)
-			ctx->mode |= RK_CRYPTO_AES_256BIT_key;
-		CRYPTO_WRITE(dev, RK_CRYPTO_AES_CTRL, ctx->mode);
-		memcpy_toio(dev->reg + RK_CRYPTO_AES_IV_0, req->iv, ivsize);
+			rctx->mode |= RK_CRYPTO_AES_256BIT_key;
+		CRYPTO_WRITE(dev, RK_CRYPTO_AES_CTRL, rctx->mode);
+		memcpy_toio(ctx->dev->reg + RK_CRYPTO_AES_KEY_0, ctx->key, ctx->keylen);
 	}
 	conf_reg |= RK_CRYPTO_BYTESWAP_BTFIFO |
 		    RK_CRYPTO_BYTESWAP_BRFIFO;
@@ -231,146 +298,138 @@
 		     RK_CRYPTO_BCDMA_ERR_ENA | RK_CRYPTO_BCDMA_DONE_ENA);
 }
 
-static void crypto_dma_start(struct rk_crypto_info *dev)
-{
-	CRYPTO_WRITE(dev, RK_CRYPTO_BRDMAS, dev->addr_in);
-	CRYPTO_WRITE(dev, RK_CRYPTO_BRDMAL, dev->count / 4);
-	CRYPTO_WRITE(dev, RK_CRYPTO_BTDMAS, dev->addr_out);
+static void crypto_dma_start(struct rk_crypto_info *dev,
+			     struct scatterlist *sgs,
+			     struct scatterlist *sgd, unsigned int todo)
+{
+	CRYPTO_WRITE(dev, RK_CRYPTO_BRDMAS, sg_dma_address(sgs));
+	CRYPTO_WRITE(dev, RK_CRYPTO_BRDMAL, todo);
+	CRYPTO_WRITE(dev, RK_CRYPTO_BTDMAS, sg_dma_address(sgd));
 	CRYPTO_WRITE(dev, RK_CRYPTO_CTRL, RK_CRYPTO_BLOCK_START |
 		     _SBF(RK_CRYPTO_BLOCK_START, 16));
 }
 
-static int rk_set_data_start(struct rk_crypto_info *dev)
+static int rk_cipher_run(struct crypto_engine *engine, void *async_req)
 {
-	int err;
-	struct skcipher_request *req =
-		skcipher_request_cast(dev->async_req);
-	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct skcipher_request *areq = container_of(async_req, struct skcipher_request, base);
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(areq);
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
-	u32 ivsize = crypto_skcipher_ivsize(tfm);
-	u8 *src_last_blk = page_address(sg_page(dev->sg_src)) +
-		dev->sg_src->offset + dev->sg_src->length - ivsize;
-
-	/* Store the iv that need to be updated in chain mode.
-	 * And update the IV buffer to contain the next IV for decryption mode.
-	 */
-	if (ctx->mode & RK_CRYPTO_DEC) {
-		memcpy(ctx->iv, src_last_blk, ivsize);
-		sg_pcopy_to_buffer(dev->first, dev->src_nents, req->iv,
-				   ivsize, dev->total - ivsize);
-	}
-
-	err = dev->load_data(dev, dev->sg_src, dev->sg_dst);
-	if (!err)
-		crypto_dma_start(dev);
-	return err;
-}
-
-static int rk_ablk_start(struct rk_crypto_info *dev)
-{
-	struct skcipher_request *req =
-		skcipher_request_cast(dev->async_req);
-	unsigned long flags;
+	struct rk_cipher_rctx *rctx = skcipher_request_ctx(areq);
+	struct scatterlist *sgs, *sgd;
 	int err = 0;
+	int ivsize = crypto_skcipher_ivsize(tfm);
+	int offset;
+	u8 iv[AES_BLOCK_SIZE];
+	u8 biv[AES_BLOCK_SIZE];
+	u8 *ivtouse = areq->iv;
+	unsigned int len = areq->cryptlen;
+	unsigned int todo;
+
+	ivsize = crypto_skcipher_ivsize(tfm);
+	if (areq->iv && crypto_skcipher_ivsize(tfm) > 0) {
+		if (rctx->mode & RK_CRYPTO_DEC) {
+			offset = areq->cryptlen - ivsize;
+			scatterwalk_map_and_copy(rctx->backup_iv, areq->src,
+						 offset, ivsize, 0);
+		}
+	}
 
-	dev->left_bytes = req->cryptlen;
-	dev->total = req->cryptlen;
-	dev->sg_src = req->src;
-	dev->first = req->src;
-	dev->src_nents = sg_nents(req->src);
-	dev->sg_dst = req->dst;
-	dev->dst_nents = sg_nents(req->dst);
-	dev->aligned = 1;
-
-	spin_lock_irqsave(&dev->lock, flags);
-	rk_ablk_hw_init(dev);
-	err = rk_set_data_start(dev);
-	spin_unlock_irqrestore(&dev->lock, flags);
-	return err;
-}
+	sgs = areq->src;
+	sgd = areq->dst;
 
-static void rk_iv_copyback(struct rk_crypto_info *dev)
-{
-	struct skcipher_request *req =
-		skcipher_request_cast(dev->async_req);
-	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
-	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
-	u32 ivsize = crypto_skcipher_ivsize(tfm);
+	while (sgs && sgd && len) {
+		if (!sgs->length) {
+			sgs = sg_next(sgs);
+			sgd = sg_next(sgd);
+			continue;
+		}
+		if (rctx->mode & RK_CRYPTO_DEC) {
+			/* we backup last block of source to be used as IV at next step */
+			offset = sgs->length - ivsize;
+			scatterwalk_map_and_copy(biv, sgs, offset, ivsize, 0);
+		}
+		if (sgs == sgd) {
+			err = dma_map_sg(ctx->dev->dev, sgs, 1, DMA_BIDIRECTIONAL);
+			if (err <= 0) {
+				err = -EINVAL;
+				goto theend_iv;
+			}
+		} else {
+			err = dma_map_sg(ctx->dev->dev, sgs, 1, DMA_TO_DEVICE);
+			if (err <= 0) {
+				err = -EINVAL;
+				goto theend_iv;
+			}
+			err = dma_map_sg(ctx->dev->dev, sgd, 1, DMA_FROM_DEVICE);
+			if (err <= 0) {
+				err = -EINVAL;
+				goto theend_sgs;
+			}
+		}
+		err = 0;
+		rk_ablk_hw_init(ctx->dev, areq);
+		if (ivsize) {
+			if (ivsize == DES_BLOCK_SIZE)
+				memcpy_toio(ctx->dev->reg + RK_CRYPTO_TDES_IV_0, ivtouse, ivsize);
+			else
+				memcpy_toio(ctx->dev->reg + RK_CRYPTO_AES_IV_0, ivtouse, ivsize);
+		}
+		reinit_completion(&ctx->dev->complete);
+		ctx->dev->status = 0;
 
-	/* Update the IV buffer to contain the next IV for encryption mode. */
-	if (!(ctx->mode & RK_CRYPTO_DEC)) {
-		if (dev->aligned) {
-			memcpy(req->iv, sg_virt(dev->sg_dst) +
-				dev->sg_dst->length - ivsize, ivsize);
+		todo = min(sg_dma_len(sgs), len);
+		len -= todo;
+		crypto_dma_start(ctx->dev, sgs, sgd, todo / 4);
+		wait_for_completion_interruptible_timeout(&ctx->dev->complete,
+							  msecs_to_jiffies(2000));
+		if (!ctx->dev->status) {
+			dev_err(ctx->dev->dev, "DMA timeout\n");
+			err = -EFAULT;
+			goto theend;
+		}
+		if (sgs == sgd) {
+			dma_unmap_sg(ctx->dev->dev, sgs, 1, DMA_BIDIRECTIONAL);
 		} else {
-			memcpy(req->iv, dev->addr_vir +
-				dev->count - ivsize, ivsize);
+			dma_unmap_sg(ctx->dev->dev, sgs, 1, DMA_TO_DEVICE);
+			dma_unmap_sg(ctx->dev->dev, sgd, 1, DMA_FROM_DEVICE);
 		}
+		if (rctx->mode & RK_CRYPTO_DEC) {
+			memcpy(iv, biv, ivsize);
+			ivtouse = iv;
+		} else {
+			offset = sgd->length - ivsize;
+			scatterwalk_map_and_copy(iv, sgd, offset, ivsize, 0);
+			ivtouse = iv;
+		}
+		sgs = sg_next(sgs);
+		sgd = sg_next(sgd);
 	}
-}
-
-static void rk_update_iv(struct rk_crypto_info *dev)
-{
-	struct skcipher_request *req =
-		skcipher_request_cast(dev->async_req);
-	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
-	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
-	u32 ivsize = crypto_skcipher_ivsize(tfm);
-	u8 *new_iv = NULL;
 
-	if (ctx->mode & RK_CRYPTO_DEC) {
-		new_iv = ctx->iv;
-	} else {
-		new_iv = page_address(sg_page(dev->sg_dst)) +
-			 dev->sg_dst->offset + dev->sg_dst->length - ivsize;
+	if (areq->iv && ivsize > 0) {
+		offset = areq->cryptlen - ivsize;
+		if (rctx->mode & RK_CRYPTO_DEC) {
+			memcpy(areq->iv, rctx->backup_iv, ivsize);
+			memzero_explicit(rctx->backup_iv, ivsize);
+		} else {
+			scatterwalk_map_and_copy(areq->iv, areq->dst, offset,
+						 ivsize, 0);
+		}
 	}
 
-	if (ivsize == DES_BLOCK_SIZE)
-		memcpy_toio(dev->reg + RK_CRYPTO_TDES_IV_0, new_iv, ivsize);
-	else if (ivsize == AES_BLOCK_SIZE)
-		memcpy_toio(dev->reg + RK_CRYPTO_AES_IV_0, new_iv, ivsize);
-}
-
-/* return:
- *	true	some err was occurred
- *	fault	no err, continue
- */
-static int rk_ablk_rx(struct rk_crypto_info *dev)
-{
-	int err = 0;
-	struct skcipher_request *req =
-		skcipher_request_cast(dev->async_req);
+theend:
+	local_bh_disable();
+	crypto_finalize_skcipher_request(engine, areq, err);
+	local_bh_enable();
+	return 0;
 
-	dev->unload_data(dev);
-	if (!dev->aligned) {
-		if (!sg_pcopy_from_buffer(req->dst, dev->dst_nents,
-					  dev->addr_vir, dev->count,
-					  dev->total - dev->left_bytes -
-					  dev->count)) {
-			err = -EINVAL;
-			goto out_rx;
-		}
-	}
-	if (dev->left_bytes) {
-		rk_update_iv(dev);
-		if (dev->aligned) {
-			if (sg_is_last(dev->sg_src)) {
-				dev_err(dev->dev, "[%s:%d] Lack of data\n",
-					__func__, __LINE__);
-				err = -ENOMEM;
-				goto out_rx;
-			}
-			dev->sg_src = sg_next(dev->sg_src);
-			dev->sg_dst = sg_next(dev->sg_dst);
-		}
-		err = rk_set_data_start(dev);
+theend_sgs:
+	if (sgs == sgd) {
+		dma_unmap_sg(ctx->dev->dev, sgs, 1, DMA_BIDIRECTIONAL);
 	} else {
-		rk_iv_copyback(dev);
-		/* here show the calculation is over without any err */
-		dev->complete(dev->async_req, 0);
-		tasklet_schedule(&dev->queue_task);
+		dma_unmap_sg(ctx->dev->dev, sgs, 1, DMA_TO_DEVICE);
+		dma_unmap_sg(ctx->dev->dev, sgd, 1, DMA_FROM_DEVICE);
 	}
-out_rx:
+theend_iv:
 	return err;
 }
 
@@ -378,26 +437,34 @@
 {
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
 	struct skcipher_alg *alg = crypto_skcipher_alg(tfm);
+	const char *name = crypto_tfm_alg_name(&tfm->base);
 	struct rk_crypto_tmp *algt;
 
 	algt = container_of(alg, struct rk_crypto_tmp, alg.skcipher);
 
 	ctx->dev = algt->dev;
-	ctx->dev->align_size = crypto_tfm_alg_alignmask(crypto_skcipher_tfm(tfm)) + 1;
-	ctx->dev->start = rk_ablk_start;
-	ctx->dev->update = rk_ablk_rx;
-	ctx->dev->complete = rk_crypto_complete;
-	ctx->dev->addr_vir = (char *)__get_free_page(GFP_KERNEL);
 
-	return ctx->dev->addr_vir ? ctx->dev->enable_clk(ctx->dev) : -ENOMEM;
+	ctx->fallback_tfm = crypto_alloc_skcipher(name, 0, CRYPTO_ALG_NEED_FALLBACK);
+	if (IS_ERR(ctx->fallback_tfm)) {
+		dev_err(ctx->dev->dev, "ERROR: Cannot allocate fallback for %s %ld\n",
+			name, PTR_ERR(ctx->fallback_tfm));
+		return PTR_ERR(ctx->fallback_tfm);
+	}
+
+	tfm->reqsize = sizeof(struct rk_cipher_rctx) +
+		crypto_skcipher_reqsize(ctx->fallback_tfm);
+
+	ctx->enginectx.op.do_one_request = rk_cipher_run;
+
+	return 0;
 }
 
 static void rk_ablk_exit_tfm(struct crypto_skcipher *tfm)
 {
 	struct rk_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
 
-	free_page((unsigned long)ctx->dev->addr_vir);
-	ctx->dev->disable_clk(ctx->dev);
+	memzero_explicit(ctx->key, ctx->keylen);
+	crypto_free_skcipher(ctx->fallback_tfm);
 }
 
 struct rk_crypto_tmp rk_ecb_aes_alg = {
@@ -406,7 +473,7 @@
 		.base.cra_name		= "ecb(aes)",
 		.base.cra_driver_name	= "ecb-aes-rk",
 		.base.cra_priority	= 300,
-		.base.cra_flags		= CRYPTO_ALG_ASYNC,
+		.base.cra_flags		= CRYPTO_ALG_ASYNC | CRYPTO_ALG_NEED_FALLBACK,
 		.base.cra_blocksize	= AES_BLOCK_SIZE,
 		.base.cra_ctxsize	= sizeof(struct rk_cipher_ctx),
 		.base.cra_alignmask	= 0x0f,
@@ -428,7 +495,7 @@
 		.base.cra_name		= "cbc(aes)",
 		.base.cra_driver_name	= "cbc-aes-rk",
 		.base.cra_priority	= 300,
-		.base.cra_flags		= CRYPTO_ALG_ASYNC,
+		.base.cra_flags		= CRYPTO_ALG_ASYNC | CRYPTO_ALG_NEED_FALLBACK,
 		.base.cra_blocksize	= AES_BLOCK_SIZE,
 		.base.cra_ctxsize	= sizeof(struct rk_cipher_ctx),
 		.base.cra_alignmask	= 0x0f,
@@ -451,7 +518,7 @@
 		.base.cra_name		= "ecb(des)",
 		.base.cra_driver_name	= "ecb-des-rk",
 		.base.cra_priority	= 300,
-		.base.cra_flags		= CRYPTO_ALG_ASYNC,
+		.base.cra_flags		= CRYPTO_ALG_ASYNC | CRYPTO_ALG_NEED_FALLBACK,
 		.base.cra_blocksize	= DES_BLOCK_SIZE,
 		.base.cra_ctxsize	= sizeof(struct rk_cipher_ctx),
 		.base.cra_alignmask	= 0x07,
@@ -473,7 +540,7 @@
 		.base.cra_name		= "cbc(des)",
 		.base.cra_driver_name	= "cbc-des-rk",
 		.base.cra_priority	= 300,
-		.base.cra_flags		= CRYPTO_ALG_ASYNC,
+		.base.cra_flags		= CRYPTO_ALG_ASYNC | CRYPTO_ALG_NEED_FALLBACK,
 		.base.cra_blocksize	= DES_BLOCK_SIZE,
 		.base.cra_ctxsize	= sizeof(struct rk_cipher_ctx),
 		.base.cra_alignmask	= 0x07,
@@ -496,7 +563,7 @@
 		.base.cra_name		= "ecb(des3_ede)",
 		.base.cra_driver_name	= "ecb-des3-ede-rk",
 		.base.cra_priority	= 300,
-		.base.cra_flags		= CRYPTO_ALG_ASYNC,
+		.base.cra_flags		= CRYPTO_ALG_ASYNC | CRYPTO_ALG_NEED_FALLBACK,
 		.base.cra_blocksize	= DES_BLOCK_SIZE,
 		.base.cra_ctxsize	= sizeof(struct rk_cipher_ctx),
 		.base.cra_alignmask	= 0x07,
@@ -506,7 +573,6 @@
 		.exit			= rk_ablk_exit_tfm,
 		.min_keysize		= DES3_EDE_KEY_SIZE,
 		.max_keysize		= DES3_EDE_KEY_SIZE,
-		.ivsize			= DES_BLOCK_SIZE,
 		.setkey			= rk_tdes_setkey,
 		.encrypt		= rk_des3_ede_ecb_encrypt,
 		.decrypt		= rk_des3_ede_ecb_decrypt,
@@ -519,7 +585,7 @@
 		.base.cra_name		= "cbc(des3_ede)",
 		.base.cra_driver_name	= "cbc-des3-ede-rk",
 		.base.cra_priority	= 300,
-		.base.cra_flags		= CRYPTO_ALG_ASYNC,
+		.base.cra_flags		= CRYPTO_ALG_ASYNC | CRYPTO_ALG_NEED_FALLBACK,
 		.base.cra_blocksize	= DES_BLOCK_SIZE,
 		.base.cra_ctxsize	= sizeof(struct rk_cipher_ctx),
 		.base.cra_alignmask	= 0x07,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/s5p-sss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/s5p-sss.c
@@ -2171,6 +2171,8 @@
 
 	variant = find_s5p_sss_version(pdev);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
 
 	/*
 	 * Note: HASH and PRNG uses the same registers in secss, avoid
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/sa2ul.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/sa2ul.c
@@ -1868,9 +1868,8 @@
 	crypto_aead_set_flags(ctx->fallback.aead,
 			      crypto_aead_get_flags(authenc) &
 			      CRYPTO_TFM_REQ_MASK);
-	crypto_aead_setkey(ctx->fallback.aead, key, keylen);
 
-	return 0;
+	return crypto_aead_setkey(ctx->fallback.aead, key, keylen);
 }
 
 static int sa_aead_setauthsize(struct crypto_aead *tfm, unsigned int authsize)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/sahara.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/sahara.c
@@ -26,10 +26,10 @@
 #include <linux/kernel.h>
 #include <linux/kthread.h>
 #include <linux/module.h>
-#include <linux/mutex.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/spinlock.h>
 
 #define SHA_BUFFER_LEN		PAGE_SIZE
 #define SAHARA_MAX_SHA_BLOCK_SIZE	SHA256_BLOCK_SIZE
@@ -44,7 +44,6 @@
 #define FLAGS_MODE_MASK		0x000f
 #define FLAGS_ENCRYPT		BIT(0)
 #define FLAGS_CBC		BIT(1)
-#define FLAGS_NEW_KEY		BIT(3)
 
 #define SAHARA_HDR_BASE			0x00800000
 #define SAHARA_HDR_SKHA_ALG_AES	0
@@ -142,8 +141,6 @@
 };
 
 struct sahara_ctx {
-	unsigned long flags;
-
 	/* AES-specific context */
 	int keylen;
 	u8 key[AES_KEYSIZE_128];
@@ -152,6 +149,7 @@
 
 struct sahara_aes_reqctx {
 	unsigned long mode;
+	u8 iv_out[AES_BLOCK_SIZE];
 	struct skcipher_request fallback_req;	// keep at the end
 };
 
@@ -196,7 +194,7 @@
 	void __iomem		*regs_base;
 	struct clk		*clk_ipg;
 	struct clk		*clk_ahb;
-	struct mutex		queue_mutex;
+	spinlock_t		queue_spinlock;
 	struct task_struct	*kthread;
 	struct completion	dma_completion;
 
@@ -447,27 +445,24 @@
 	int ret;
 	int i, j;
 	int idx = 0;
+	u32 len;
 
-	/* Copy new key if necessary */
-	if (ctx->flags & FLAGS_NEW_KEY) {
-		memcpy(dev->key_base, ctx->key, ctx->keylen);
-		ctx->flags &= ~FLAGS_NEW_KEY;
-
-		if (dev->flags & FLAGS_CBC) {
-			dev->hw_desc[idx]->len1 = AES_BLOCK_SIZE;
-			dev->hw_desc[idx]->p1 = dev->iv_phys_base;
-		} else {
-			dev->hw_desc[idx]->len1 = 0;
-			dev->hw_desc[idx]->p1 = 0;
-		}
-		dev->hw_desc[idx]->len2 = ctx->keylen;
-		dev->hw_desc[idx]->p2 = dev->key_phys_base;
-		dev->hw_desc[idx]->next = dev->hw_phys_desc[1];
-
-		dev->hw_desc[idx]->hdr = sahara_aes_key_hdr(dev);
+	memcpy(dev->key_base, ctx->key, ctx->keylen);
 
-		idx++;
+	if (dev->flags & FLAGS_CBC) {
+		dev->hw_desc[idx]->len1 = AES_BLOCK_SIZE;
+		dev->hw_desc[idx]->p1 = dev->iv_phys_base;
+	} else {
+		dev->hw_desc[idx]->len1 = 0;
+		dev->hw_desc[idx]->p1 = 0;
 	}
+	dev->hw_desc[idx]->len2 = ctx->keylen;
+	dev->hw_desc[idx]->p2 = dev->key_phys_base;
+	dev->hw_desc[idx]->next = dev->hw_phys_desc[1];
+	dev->hw_desc[idx]->hdr = sahara_aes_key_hdr(dev);
+
+	idx++;
+
 
 	dev->nb_in_sg = sg_nents_for_len(dev->in_sg, dev->total);
 	if (dev->nb_in_sg < 0) {
@@ -489,24 +484,27 @@
 			 DMA_TO_DEVICE);
 	if (ret != dev->nb_in_sg) {
 		dev_err(dev->device, "couldn't map in sg\n");
-		goto unmap_in;
+		return -EINVAL;
 	}
+
 	ret = dma_map_sg(dev->device, dev->out_sg, dev->nb_out_sg,
 			 DMA_FROM_DEVICE);
 	if (ret != dev->nb_out_sg) {
 		dev_err(dev->device, "couldn't map out sg\n");
-		goto unmap_out;
+		goto unmap_in;
 	}
 
 	/* Create input links */
 	dev->hw_desc[idx]->p1 = dev->hw_phys_link[0];
 	sg = dev->in_sg;
+	len = dev->total;
 	for (i = 0; i < dev->nb_in_sg; i++) {
-		dev->hw_link[i]->len = sg->length;
+		dev->hw_link[i]->len = min(len, sg->length);
 		dev->hw_link[i]->p = sg->dma_address;
 		if (i == (dev->nb_in_sg - 1)) {
 			dev->hw_link[i]->next = 0;
 		} else {
+			len -= min(len, sg->length);
 			dev->hw_link[i]->next = dev->hw_phys_link[i + 1];
 			sg = sg_next(sg);
 		}
@@ -515,12 +513,14 @@
 	/* Create output links */
 	dev->hw_desc[idx]->p2 = dev->hw_phys_link[i];
 	sg = dev->out_sg;
+	len = dev->total;
 	for (j = i; j < dev->nb_out_sg + i; j++) {
-		dev->hw_link[j]->len = sg->length;
+		dev->hw_link[j]->len = min(len, sg->length);
 		dev->hw_link[j]->p = sg->dma_address;
 		if (j == (dev->nb_out_sg + i - 1)) {
 			dev->hw_link[j]->next = 0;
 		} else {
+			len -= min(len, sg->length);
 			dev->hw_link[j]->next = dev->hw_phys_link[j + 1];
 			sg = sg_next(sg);
 		}
@@ -539,9 +539,6 @@
 
 	return 0;
 
-unmap_out:
-	dma_unmap_sg(dev->device, dev->out_sg, dev->nb_out_sg,
-		DMA_FROM_DEVICE);
 unmap_in:
 	dma_unmap_sg(dev->device, dev->in_sg, dev->nb_in_sg,
 		DMA_TO_DEVICE);
@@ -549,8 +546,24 @@
 	return -EINVAL;
 }
 
+static void sahara_aes_cbc_update_iv(struct skcipher_request *req)
+{
+	struct crypto_skcipher *skcipher = crypto_skcipher_reqtfm(req);
+	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
+	unsigned int ivsize = crypto_skcipher_ivsize(skcipher);
+
+	/* Update IV buffer to contain the last ciphertext block */
+	if (rctx->mode & FLAGS_ENCRYPT) {
+		sg_pcopy_to_buffer(req->dst, sg_nents(req->dst), req->iv,
+				   ivsize, req->cryptlen - ivsize);
+	} else {
+		memcpy(req->iv, rctx->iv_out, ivsize);
+	}
+}
+
 static int sahara_aes_process(struct skcipher_request *req)
 {
+	struct crypto_skcipher *skcipher = crypto_skcipher_reqtfm(req);
 	struct sahara_dev *dev = dev_ptr;
 	struct sahara_ctx *ctx;
 	struct sahara_aes_reqctx *rctx;
@@ -572,8 +585,17 @@
 	rctx->mode &= FLAGS_MODE_MASK;
 	dev->flags = (dev->flags & ~FLAGS_MODE_MASK) | rctx->mode;
 
-	if ((dev->flags & FLAGS_CBC) && req->iv)
-		memcpy(dev->iv_base, req->iv, AES_KEYSIZE_128);
+	if ((dev->flags & FLAGS_CBC) && req->iv) {
+		unsigned int ivsize = crypto_skcipher_ivsize(skcipher);
+
+		memcpy(dev->iv_base, req->iv, ivsize);
+
+		if (!(dev->flags & FLAGS_ENCRYPT)) {
+			sg_pcopy_to_buffer(req->src, sg_nents(req->src),
+					   rctx->iv_out, ivsize,
+					   req->cryptlen - ivsize);
+		}
+	}
 
 	/* assign new context to device */
 	dev->ctx = ctx;
@@ -586,16 +608,20 @@
 
 	timeout = wait_for_completion_timeout(&dev->dma_completion,
 				msecs_to_jiffies(SAHARA_TIMEOUT_MS));
-	if (!timeout) {
-		dev_err(dev->device, "AES timeout\n");
-		return -ETIMEDOUT;
-	}
 
 	dma_unmap_sg(dev->device, dev->out_sg, dev->nb_out_sg,
 		DMA_FROM_DEVICE);
 	dma_unmap_sg(dev->device, dev->in_sg, dev->nb_in_sg,
 		DMA_TO_DEVICE);
 
+	if (!timeout) {
+		dev_err(dev->device, "AES timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	if ((dev->flags & FLAGS_CBC) && req->iv)
+		sahara_aes_cbc_update_iv(req);
+
 	return 0;
 }
 
@@ -609,7 +635,6 @@
 	/* SAHARA only supports 128bit keys */
 	if (keylen == AES_KEYSIZE_128) {
 		memcpy(ctx->key, key, keylen);
-		ctx->flags |= FLAGS_NEW_KEY;
 		return 0;
 	}
 
@@ -625,12 +650,40 @@
 	return crypto_skcipher_setkey(ctx->fallback, key, keylen);
 }
 
+static int sahara_aes_fallback(struct skcipher_request *req, unsigned long mode)
+{
+	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
+	struct sahara_ctx *ctx = crypto_skcipher_ctx(
+		crypto_skcipher_reqtfm(req));
+
+	skcipher_request_set_tfm(&rctx->fallback_req, ctx->fallback);
+	skcipher_request_set_callback(&rctx->fallback_req,
+				      req->base.flags,
+				      req->base.complete,
+				      req->base.data);
+	skcipher_request_set_crypt(&rctx->fallback_req, req->src,
+				   req->dst, req->cryptlen, req->iv);
+
+	if (mode & FLAGS_ENCRYPT)
+		return crypto_skcipher_encrypt(&rctx->fallback_req);
+
+	return crypto_skcipher_decrypt(&rctx->fallback_req);
+}
+
 static int sahara_aes_crypt(struct skcipher_request *req, unsigned long mode)
 {
 	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
+	struct sahara_ctx *ctx = crypto_skcipher_ctx(
+		crypto_skcipher_reqtfm(req));
 	struct sahara_dev *dev = dev_ptr;
 	int err = 0;
 
+	if (!req->cryptlen)
+		return 0;
+
+	if (unlikely(ctx->keylen != AES_KEYSIZE_128))
+		return sahara_aes_fallback(req, mode);
+
 	dev_dbg(dev->device, "nbytes: %d, enc: %d, cbc: %d\n",
 		req->cryptlen, !!(mode & FLAGS_ENCRYPT), !!(mode & FLAGS_CBC));
 
@@ -642,9 +695,9 @@
 
 	rctx->mode = mode;
 
-	mutex_lock(&dev->queue_mutex);
+	spin_lock_bh(&dev->queue_spinlock);
 	err = crypto_enqueue_request(&dev->queue, &req->base);
-	mutex_unlock(&dev->queue_mutex);
+	spin_unlock_bh(&dev->queue_spinlock);
 
 	wake_up_process(dev->kthread);
 
@@ -653,81 +706,21 @@
 
 static int sahara_aes_ecb_encrypt(struct skcipher_request *req)
 {
-	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
-	struct sahara_ctx *ctx = crypto_skcipher_ctx(
-		crypto_skcipher_reqtfm(req));
-
-	if (unlikely(ctx->keylen != AES_KEYSIZE_128)) {
-		skcipher_request_set_tfm(&rctx->fallback_req, ctx->fallback);
-		skcipher_request_set_callback(&rctx->fallback_req,
-					      req->base.flags,
-					      req->base.complete,
-					      req->base.data);
-		skcipher_request_set_crypt(&rctx->fallback_req, req->src,
-					   req->dst, req->cryptlen, req->iv);
-		return crypto_skcipher_encrypt(&rctx->fallback_req);
-	}
-
 	return sahara_aes_crypt(req, FLAGS_ENCRYPT);
 }
 
 static int sahara_aes_ecb_decrypt(struct skcipher_request *req)
 {
-	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
-	struct sahara_ctx *ctx = crypto_skcipher_ctx(
-		crypto_skcipher_reqtfm(req));
-
-	if (unlikely(ctx->keylen != AES_KEYSIZE_128)) {
-		skcipher_request_set_tfm(&rctx->fallback_req, ctx->fallback);
-		skcipher_request_set_callback(&rctx->fallback_req,
-					      req->base.flags,
-					      req->base.complete,
-					      req->base.data);
-		skcipher_request_set_crypt(&rctx->fallback_req, req->src,
-					   req->dst, req->cryptlen, req->iv);
-		return crypto_skcipher_decrypt(&rctx->fallback_req);
-	}
-
 	return sahara_aes_crypt(req, 0);
 }
 
 static int sahara_aes_cbc_encrypt(struct skcipher_request *req)
 {
-	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
-	struct sahara_ctx *ctx = crypto_skcipher_ctx(
-		crypto_skcipher_reqtfm(req));
-
-	if (unlikely(ctx->keylen != AES_KEYSIZE_128)) {
-		skcipher_request_set_tfm(&rctx->fallback_req, ctx->fallback);
-		skcipher_request_set_callback(&rctx->fallback_req,
-					      req->base.flags,
-					      req->base.complete,
-					      req->base.data);
-		skcipher_request_set_crypt(&rctx->fallback_req, req->src,
-					   req->dst, req->cryptlen, req->iv);
-		return crypto_skcipher_encrypt(&rctx->fallback_req);
-	}
-
 	return sahara_aes_crypt(req, FLAGS_ENCRYPT | FLAGS_CBC);
 }
 
 static int sahara_aes_cbc_decrypt(struct skcipher_request *req)
 {
-	struct sahara_aes_reqctx *rctx = skcipher_request_ctx(req);
-	struct sahara_ctx *ctx = crypto_skcipher_ctx(
-		crypto_skcipher_reqtfm(req));
-
-	if (unlikely(ctx->keylen != AES_KEYSIZE_128)) {
-		skcipher_request_set_tfm(&rctx->fallback_req, ctx->fallback);
-		skcipher_request_set_callback(&rctx->fallback_req,
-					      req->base.flags,
-					      req->base.complete,
-					      req->base.data);
-		skcipher_request_set_crypt(&rctx->fallback_req, req->src,
-					   req->dst, req->cryptlen, req->iv);
-		return crypto_skcipher_decrypt(&rctx->fallback_req);
-	}
-
 	return sahara_aes_crypt(req, FLAGS_CBC);
 }
 
@@ -784,6 +777,7 @@
 				       int start)
 {
 	struct scatterlist *sg;
+	unsigned int len;
 	unsigned int i;
 	int ret;
 
@@ -805,12 +799,14 @@
 	if (!ret)
 		return -EFAULT;
 
+	len = rctx->total;
 	for (i = start; i < dev->nb_in_sg + start; i++) {
-		dev->hw_link[i]->len = sg->length;
+		dev->hw_link[i]->len = min(len, sg->length);
 		dev->hw_link[i]->p = sg->dma_address;
 		if (i == (dev->nb_in_sg + start - 1)) {
 			dev->hw_link[i]->next = 0;
 		} else {
+			len -= min(len, sg->length);
 			dev->hw_link[i]->next = dev->hw_phys_link[i + 1];
 			sg = sg_next(sg);
 		}
@@ -891,24 +887,6 @@
 	return 0;
 }
 
-static int sahara_walk_and_recalc(struct scatterlist *sg, unsigned int nbytes)
-{
-	if (!sg || !sg->length)
-		return nbytes;
-
-	while (nbytes && sg) {
-		if (nbytes <= sg->length) {
-			sg->length = nbytes;
-			sg_mark_end(sg);
-			break;
-		}
-		nbytes -= sg->length;
-		sg = sg_next(sg);
-	}
-
-	return nbytes;
-}
-
 static int sahara_sha_prepare_request(struct ahash_request *req)
 {
 	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
@@ -945,36 +923,20 @@
 					hash_later, 0);
 	}
 
-	/* nbytes should now be multiple of blocksize */
-	req->nbytes = req->nbytes - hash_later;
-
-	sahara_walk_and_recalc(req->src, req->nbytes);
-
+	rctx->total = len - hash_later;
 	/* have data from previous operation and current */
 	if (rctx->buf_cnt && req->nbytes) {
 		sg_init_table(rctx->in_sg_chain, 2);
 		sg_set_buf(rctx->in_sg_chain, rctx->rembuf, rctx->buf_cnt);
-
 		sg_chain(rctx->in_sg_chain, 2, req->src);
-
-		rctx->total = req->nbytes + rctx->buf_cnt;
 		rctx->in_sg = rctx->in_sg_chain;
-
-		req->src = rctx->in_sg_chain;
 	/* only data from previous operation */
 	} else if (rctx->buf_cnt) {
-		if (req->src)
-			rctx->in_sg = req->src;
-		else
-			rctx->in_sg = rctx->in_sg_chain;
-		/* buf was copied into rembuf above */
+		rctx->in_sg = rctx->in_sg_chain;
 		sg_init_one(rctx->in_sg, rctx->rembuf, rctx->buf_cnt);
-		rctx->total = rctx->buf_cnt;
 	/* no data from previous operation */
 	} else {
 		rctx->in_sg = req->src;
-		rctx->total = req->nbytes;
-		req->src = rctx->in_sg;
 	}
 
 	/* on next call, we only have the remaining data in the buffer */
@@ -995,7 +957,10 @@
 		return ret;
 
 	if (rctx->first) {
-		sahara_sha_hw_data_descriptor_create(dev, rctx, req, 0);
+		ret = sahara_sha_hw_data_descriptor_create(dev, rctx, req, 0);
+		if (ret)
+			return ret;
+
 		dev->hw_desc[0]->next = 0;
 		rctx->first = 0;
 	} else {
@@ -1003,7 +968,10 @@
 
 		sahara_sha_hw_context_descriptor_create(dev, rctx, req, 0);
 		dev->hw_desc[0]->next = dev->hw_phys_desc[1];
-		sahara_sha_hw_data_descriptor_create(dev, rctx, req, 1);
+		ret = sahara_sha_hw_data_descriptor_create(dev, rctx, req, 1);
+		if (ret)
+			return ret;
+
 		dev->hw_desc[1]->next = 0;
 	}
 
@@ -1016,18 +984,19 @@
 
 	timeout = wait_for_completion_timeout(&dev->dma_completion,
 				msecs_to_jiffies(SAHARA_TIMEOUT_MS));
-	if (!timeout) {
-		dev_err(dev->device, "SHA timeout\n");
-		return -ETIMEDOUT;
-	}
 
 	if (rctx->sg_in_idx)
 		dma_unmap_sg(dev->device, dev->in_sg, dev->nb_in_sg,
 			     DMA_TO_DEVICE);
 
+	if (!timeout) {
+		dev_err(dev->device, "SHA timeout\n");
+		return -ETIMEDOUT;
+	}
+
 	memcpy(rctx->context, dev->context_base, rctx->context_size);
 
-	if (req->result)
+	if (req->result && rctx->last)
 		memcpy(req->result, rctx->context, rctx->digest_size);
 
 	return 0;
@@ -1043,10 +1012,10 @@
 	do {
 		__set_current_state(TASK_INTERRUPTIBLE);
 
-		mutex_lock(&dev->queue_mutex);
+		spin_lock_bh(&dev->queue_spinlock);
 		backlog = crypto_get_backlog(&dev->queue);
 		async_req = crypto_dequeue_request(&dev->queue);
-		mutex_unlock(&dev->queue_mutex);
+		spin_unlock_bh(&dev->queue_spinlock);
 
 		if (backlog)
 			backlog->complete(backlog, -EINPROGRESS);
@@ -1092,9 +1061,9 @@
 		rctx->first = 1;
 	}
 
-	mutex_lock(&dev->queue_mutex);
+	spin_lock_bh(&dev->queue_spinlock);
 	ret = crypto_enqueue_request(&dev->queue, &req->base);
-	mutex_unlock(&dev->queue_mutex);
+	spin_unlock_bh(&dev->queue_spinlock);
 
 	wake_up_process(dev->kthread);
 
@@ -1171,8 +1140,7 @@
 static int sahara_sha_cra_init(struct crypto_tfm *tfm)
 {
 	crypto_ahash_set_reqsize(__crypto_ahash_cast(tfm),
-				 sizeof(struct sahara_sha_reqctx) +
-				 SHA_BUFFER_LEN + SHA256_BLOCK_SIZE);
+				 sizeof(struct sahara_sha_reqctx));
 
 	return 0;
 }
@@ -1449,7 +1417,7 @@
 
 	crypto_init_queue(&dev->queue, SAHARA_QUEUE_LENGTH);
 
-	mutex_init(&dev->queue_mutex);
+	spin_lock_init(&dev->queue_spinlock);
 
 	dev_ptr = dev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/stm32/stm32-crc32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/stm32/stm32-crc32.c
@@ -104,7 +104,7 @@
 	struct stm32_crc *crc;
 
 	spin_lock_bh(&crc_list.lock);
-	crc = list_first_entry(&crc_list.dev_list, struct stm32_crc, list);
+	crc = list_first_entry_or_null(&crc_list.dev_list, struct stm32_crc, list);
 	if (crc)
 		list_move_tail(&crc->list, &crc_list.dev_list);
 	spin_unlock_bh(&crc_list.lock);
@@ -279,7 +279,7 @@
 		.digestsize     = CHKSUM_DIGEST_SIZE,
 		.base           = {
 			.cra_name               = "crc32",
-			.cra_driver_name        = DRIVER_NAME,
+			.cra_driver_name        = "stm32-crc32-crc32",
 			.cra_priority           = 200,
 			.cra_flags		= CRYPTO_ALG_OPTIONAL_KEY,
 			.cra_blocksize          = CHKSUM_BLOCK_SIZE,
@@ -301,7 +301,7 @@
 		.digestsize     = CHKSUM_DIGEST_SIZE,
 		.base           = {
 			.cra_name               = "crc32c",
-			.cra_driver_name        = DRIVER_NAME,
+			.cra_driver_name        = "stm32-crc32-crc32c",
 			.cra_priority           = 200,
 			.cra_flags		= CRYPTO_ALG_OPTIONAL_KEY,
 			.cra_blocksize          = CHKSUM_BLOCK_SIZE,
@@ -384,8 +384,10 @@
 	struct stm32_crc *crc = platform_get_drvdata(pdev);
 	int ret = pm_runtime_get_sync(crc->dev);
 
-	if (ret < 0)
+	if (ret < 0) {
+		pm_runtime_put_noidle(crc->dev);
 		return ret;
+	}
 
 	spin_lock(&crc_list.lock);
 	list_del(&crc->list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/stm32/stm32-cryp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/stm32/stm32-cryp.c
@@ -37,7 +37,6 @@
 /* Mode mask = bits [15..0] */
 #define FLG_MODE_MASK           GENMASK(15, 0)
 /* Bit [31..16] status  */
-#define FLG_CCM_PADDED_WA       BIT(16)
 
 /* Registers */
 #define CRYP_CR                 0x00000000
@@ -105,8 +104,6 @@
 /* Misc */
 #define AES_BLOCK_32            (AES_BLOCK_SIZE / sizeof(u32))
 #define GCM_CTR_INIT            2
-#define _walked_in              (cryp->in_walk.offset - cryp->in_sg->offset)
-#define _walked_out             (cryp->out_walk.offset - cryp->out_sg->offset)
 #define CRYP_AUTOSUSPEND_DELAY	50
 
 struct stm32_cryp_caps {
@@ -144,26 +141,16 @@
 	size_t                  authsize;
 	size_t                  hw_blocksize;
 
-	size_t                  total_in;
-	size_t                  total_in_save;
-	size_t                  total_out;
-	size_t                  total_out_save;
+	size_t                  payload_in;
+	size_t                  header_in;
+	size_t                  payload_out;
 
-	struct scatterlist      *in_sg;
 	struct scatterlist      *out_sg;
-	struct scatterlist      *out_sg_save;
-
-	struct scatterlist      in_sgl;
-	struct scatterlist      out_sgl;
-	bool                    sgs_copied;
-
-	int                     in_sg_len;
-	int                     out_sg_len;
 
 	struct scatter_walk     in_walk;
 	struct scatter_walk     out_walk;
 
-	u32                     last_ctr[4];
+	__be32                  last_ctr[4];
 	u32                     gcm_ctr;
 };
 
@@ -262,6 +249,7 @@
 }
 
 static int stm32_cryp_read_auth_tag(struct stm32_cryp *cryp);
+static void stm32_cryp_finish_req(struct stm32_cryp *cryp, int err);
 
 static struct stm32_cryp *stm32_cryp_find_dev(struct stm32_cryp_ctx *ctx)
 {
@@ -283,103 +271,6 @@
 	return cryp;
 }
 
-static int stm32_cryp_check_aligned(struct scatterlist *sg, size_t total,
-				    size_t align)
-{
-	int len = 0;
-
-	if (!total)
-		return 0;
-
-	if (!IS_ALIGNED(total, align))
-		return -EINVAL;
-
-	while (sg) {
-		if (!IS_ALIGNED(sg->offset, sizeof(u32)))
-			return -EINVAL;
-
-		if (!IS_ALIGNED(sg->length, align))
-			return -EINVAL;
-
-		len += sg->length;
-		sg = sg_next(sg);
-	}
-
-	if (len != total)
-		return -EINVAL;
-
-	return 0;
-}
-
-static int stm32_cryp_check_io_aligned(struct stm32_cryp *cryp)
-{
-	int ret;
-
-	ret = stm32_cryp_check_aligned(cryp->in_sg, cryp->total_in,
-				       cryp->hw_blocksize);
-	if (ret)
-		return ret;
-
-	ret = stm32_cryp_check_aligned(cryp->out_sg, cryp->total_out,
-				       cryp->hw_blocksize);
-
-	return ret;
-}
-
-static void sg_copy_buf(void *buf, struct scatterlist *sg,
-			unsigned int start, unsigned int nbytes, int out)
-{
-	struct scatter_walk walk;
-
-	if (!nbytes)
-		return;
-
-	scatterwalk_start(&walk, sg);
-	scatterwalk_advance(&walk, start);
-	scatterwalk_copychunks(buf, &walk, nbytes, out);
-	scatterwalk_done(&walk, out, 0);
-}
-
-static int stm32_cryp_copy_sgs(struct stm32_cryp *cryp)
-{
-	void *buf_in, *buf_out;
-	int pages, total_in, total_out;
-
-	if (!stm32_cryp_check_io_aligned(cryp)) {
-		cryp->sgs_copied = 0;
-		return 0;
-	}
-
-	total_in = ALIGN(cryp->total_in, cryp->hw_blocksize);
-	pages = total_in ? get_order(total_in) : 1;
-	buf_in = (void *)__get_free_pages(GFP_ATOMIC, pages);
-
-	total_out = ALIGN(cryp->total_out, cryp->hw_blocksize);
-	pages = total_out ? get_order(total_out) : 1;
-	buf_out = (void *)__get_free_pages(GFP_ATOMIC, pages);
-
-	if (!buf_in || !buf_out) {
-		dev_err(cryp->dev, "Can't allocate pages when unaligned\n");
-		cryp->sgs_copied = 0;
-		return -EFAULT;
-	}
-
-	sg_copy_buf(buf_in, cryp->in_sg, 0, cryp->total_in, 0);
-
-	sg_init_one(&cryp->in_sgl, buf_in, total_in);
-	cryp->in_sg = &cryp->in_sgl;
-	cryp->in_sg_len = 1;
-
-	sg_init_one(&cryp->out_sgl, buf_out, total_out);
-	cryp->out_sg_save = cryp->out_sg;
-	cryp->out_sg = &cryp->out_sgl;
-	cryp->out_sg_len = 1;
-
-	cryp->sgs_copied = 1;
-
-	return 0;
-}
-
 static void stm32_cryp_hw_write_iv(struct stm32_cryp *cryp, __be32 *iv)
 {
 	if (!iv)
@@ -481,16 +372,99 @@
 
 	/* Wait for end of processing */
 	ret = stm32_cryp_wait_enable(cryp);
-	if (ret)
+	if (ret) {
 		dev_err(cryp->dev, "Timeout (gcm init)\n");
+		return ret;
+	}
 
-	return ret;
+	/* Prepare next phase */
+	if (cryp->areq->assoclen) {
+		cfg |= CR_PH_HEADER;
+		stm32_cryp_write(cryp, CRYP_CR, cfg);
+	} else if (stm32_cryp_get_input_text_len(cryp)) {
+		cfg |= CR_PH_PAYLOAD;
+		stm32_cryp_write(cryp, CRYP_CR, cfg);
+	}
+
+	return 0;
+}
+
+static void stm32_crypt_gcmccm_end_header(struct stm32_cryp *cryp)
+{
+	u32 cfg;
+	int err;
+
+	/* Check if whole header written */
+	if (!cryp->header_in) {
+		/* Wait for completion */
+		err = stm32_cryp_wait_busy(cryp);
+		if (err) {
+			dev_err(cryp->dev, "Timeout (gcm/ccm header)\n");
+			stm32_cryp_write(cryp, CRYP_IMSCR, 0);
+			stm32_cryp_finish_req(cryp, err);
+			return;
+		}
+
+		if (stm32_cryp_get_input_text_len(cryp)) {
+			/* Phase 3 : payload */
+			cfg = stm32_cryp_read(cryp, CRYP_CR);
+			cfg &= ~CR_CRYPEN;
+			stm32_cryp_write(cryp, CRYP_CR, cfg);
+
+			cfg &= ~CR_PH_MASK;
+			cfg |= CR_PH_PAYLOAD | CR_CRYPEN;
+			stm32_cryp_write(cryp, CRYP_CR, cfg);
+		} else {
+			/*
+			 * Phase 4 : tag.
+			 * Nothing to read, nothing to write, caller have to
+			 * end request
+			 */
+		}
+	}
+}
+
+static void stm32_cryp_write_ccm_first_header(struct stm32_cryp *cryp)
+{
+	unsigned int i;
+	size_t written;
+	size_t len;
+	u32 alen = cryp->areq->assoclen;
+	u32 block[AES_BLOCK_32] = {0};
+	u8 *b8 = (u8 *)block;
+
+	if (alen <= 65280) {
+		/* Write first u32 of B1 */
+		b8[0] = (alen >> 8) & 0xFF;
+		b8[1] = alen & 0xFF;
+		len = 2;
+	} else {
+		/* Build the two first u32 of B1 */
+		b8[0] = 0xFF;
+		b8[1] = 0xFE;
+		b8[2] = (alen & 0xFF000000) >> 24;
+		b8[3] = (alen & 0x00FF0000) >> 16;
+		b8[4] = (alen & 0x0000FF00) >> 8;
+		b8[5] = alen & 0x000000FF;
+		len = 6;
+	}
+
+	written = min_t(size_t, AES_BLOCK_SIZE - len, alen);
+
+	scatterwalk_copychunks((char *)block + len, &cryp->in_walk, written, 0);
+	for (i = 0; i < AES_BLOCK_32; i++)
+		stm32_cryp_write(cryp, CRYP_DIN, block[i]);
+
+	cryp->header_in -= written;
+
+	stm32_crypt_gcmccm_end_header(cryp);
 }
 
 static int stm32_cryp_ccm_init(struct stm32_cryp *cryp, u32 cfg)
 {
 	int ret;
-	u8 iv[AES_BLOCK_SIZE], b0[AES_BLOCK_SIZE];
+	u32 iv_32[AES_BLOCK_32], b0_32[AES_BLOCK_32];
+	u8 *iv = (u8 *)iv_32, *b0 = (u8 *)b0_32;
 	__be32 *bd;
 	u32 *d;
 	unsigned int i, textlen;
@@ -531,10 +505,24 @@
 
 	/* Wait for end of processing */
 	ret = stm32_cryp_wait_enable(cryp);
-	if (ret)
+	if (ret) {
 		dev_err(cryp->dev, "Timeout (ccm init)\n");
+		return ret;
+	}
 
-	return ret;
+	/* Prepare next phase */
+	if (cryp->areq->assoclen) {
+		cfg |= CR_PH_HEADER | CR_CRYPEN;
+		stm32_cryp_write(cryp, CRYP_CR, cfg);
+
+		/* Write first (special) block (may move to next phase [payload]) */
+		stm32_cryp_write_ccm_first_header(cryp);
+	} else if (stm32_cryp_get_input_text_len(cryp)) {
+		cfg |= CR_PH_PAYLOAD;
+		stm32_cryp_write(cryp, CRYP_CR, cfg);
+	}
+
+	return 0;
 }
 
 static int stm32_cryp_hw_init(struct stm32_cryp *cryp)
@@ -542,7 +530,7 @@
 	int ret;
 	u32 cfg, hw_mode;
 
-	pm_runtime_resume_and_get(cryp->dev);
+	pm_runtime_get_sync(cryp->dev);
 
 	/* Disable interrupt */
 	stm32_cryp_write(cryp, CRYP_IMSCR, 0);
@@ -605,16 +593,6 @@
 		if (ret)
 			return ret;
 
-		/* Phase 2 : header (authenticated data) */
-		if (cryp->areq->assoclen) {
-			cfg |= CR_PH_HEADER;
-		} else if (stm32_cryp_get_input_text_len(cryp)) {
-			cfg |= CR_PH_PAYLOAD;
-			stm32_cryp_write(cryp, CRYP_CR, cfg);
-		} else {
-			cfg |= CR_PH_INIT;
-		}
-
 		break;
 
 	case CR_DES_CBC:
@@ -633,8 +611,6 @@
 
 	stm32_cryp_write(cryp, CRYP_CR, cfg);
 
-	cryp->flags &= ~FLG_CCM_PADDED_WA;
-
 	return 0;
 }
 
@@ -644,28 +620,9 @@
 		/* Phase 4 : output tag */
 		err = stm32_cryp_read_auth_tag(cryp);
 
-	if (!err && (!(is_gcm(cryp) || is_ccm(cryp))))
+	if (!err && (!(is_gcm(cryp) || is_ccm(cryp) || is_ecb(cryp))))
 		stm32_cryp_get_iv(cryp);
 
-	if (cryp->sgs_copied) {
-		void *buf_in, *buf_out;
-		int pages, len;
-
-		buf_in = sg_virt(&cryp->in_sgl);
-		buf_out = sg_virt(&cryp->out_sgl);
-
-		sg_copy_buf(buf_out, cryp->out_sg_save, 0,
-			    cryp->total_out_save, 1);
-
-		len = ALIGN(cryp->total_in_save, cryp->hw_blocksize);
-		pages = len ? get_order(len) : 1;
-		free_pages((unsigned long)buf_in, pages);
-
-		len = ALIGN(cryp->total_out_save, cryp->hw_blocksize);
-		pages = len ? get_order(len) : 1;
-		free_pages((unsigned long)buf_out, pages);
-	}
-
 	pm_runtime_mark_last_busy(cryp->dev);
 	pm_runtime_put_autosuspend(cryp->dev);
 
@@ -674,8 +631,6 @@
 	else
 		crypto_finalize_skcipher_request(cryp->engine, cryp->req,
 						   err);
-
-	memset(cryp->ctx->key, 0, cryp->ctx->keylen);
 }
 
 static int stm32_cryp_cpu_start(struct stm32_cryp *cryp)
@@ -801,7 +756,20 @@
 static int stm32_cryp_aes_gcm_setauthsize(struct crypto_aead *tfm,
 					  unsigned int authsize)
 {
-	return authsize == AES_BLOCK_SIZE ? 0 : -EINVAL;
+	switch (authsize) {
+	case 4:
+	case 8:
+	case 12:
+	case 13:
+	case 14:
+	case 15:
+	case 16:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
 }
 
 static int stm32_cryp_aes_ccm_setauthsize(struct crypto_aead *tfm,
@@ -825,31 +793,61 @@
 
 static int stm32_cryp_aes_ecb_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % AES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_AES | FLG_ECB | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_aes_ecb_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % AES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_AES | FLG_ECB);
 }
 
 static int stm32_cryp_aes_cbc_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % AES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_AES | FLG_CBC | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_aes_cbc_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % AES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_AES | FLG_CBC);
 }
 
 static int stm32_cryp_aes_ctr_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_AES | FLG_CTR | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_aes_ctr_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_AES | FLG_CTR);
 }
 
@@ -863,53 +861,122 @@
 	return stm32_cryp_aead_crypt(req, FLG_AES | FLG_GCM);
 }
 
+static inline int crypto_ccm_check_iv(const u8 *iv)
+{
+	/* 2 <= L <= 8, so 1 <= L' <= 7. */
+	if (iv[0] < 1 || iv[0] > 7)
+		return -EINVAL;
+
+	return 0;
+}
+
 static int stm32_cryp_aes_ccm_encrypt(struct aead_request *req)
 {
+	int err;
+
+	err = crypto_ccm_check_iv(req->iv);
+	if (err)
+		return err;
+
 	return stm32_cryp_aead_crypt(req, FLG_AES | FLG_CCM | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_aes_ccm_decrypt(struct aead_request *req)
 {
+	int err;
+
+	err = crypto_ccm_check_iv(req->iv);
+	if (err)
+		return err;
+
 	return stm32_cryp_aead_crypt(req, FLG_AES | FLG_CCM);
 }
 
 static int stm32_cryp_des_ecb_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_DES | FLG_ECB | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_des_ecb_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_DES | FLG_ECB);
 }
 
 static int stm32_cryp_des_cbc_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_DES | FLG_CBC | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_des_cbc_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_DES | FLG_CBC);
 }
 
 static int stm32_cryp_tdes_ecb_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_TDES | FLG_ECB | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_tdes_ecb_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_TDES | FLG_ECB);
 }
 
 static int stm32_cryp_tdes_cbc_encrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_TDES | FLG_CBC | FLG_ENCRYPT);
 }
 
 static int stm32_cryp_tdes_cbc_decrypt(struct skcipher_request *req)
 {
+	if (req->cryptlen % DES_BLOCK_SIZE)
+		return -EINVAL;
+
+	if (req->cryptlen == 0)
+		return 0;
+
 	return stm32_cryp_crypt(req, FLG_TDES | FLG_CBC);
 }
 
@@ -919,6 +986,7 @@
 	struct stm32_cryp_ctx *ctx;
 	struct stm32_cryp *cryp;
 	struct stm32_cryp_reqctx *rctx;
+	struct scatterlist *in_sg;
 	int ret;
 
 	if (!req && !areq)
@@ -944,76 +1012,55 @@
 	if (req) {
 		cryp->req = req;
 		cryp->areq = NULL;
-		cryp->total_in = req->cryptlen;
-		cryp->total_out = cryp->total_in;
+		cryp->header_in = 0;
+		cryp->payload_in = req->cryptlen;
+		cryp->payload_out = req->cryptlen;
+		cryp->authsize = 0;
 	} else {
 		/*
 		 * Length of input and output data:
 		 * Encryption case:
-		 *  INPUT  =   AssocData  ||   PlainText
+		 *  INPUT  = AssocData   ||     PlainText
 		 *          <- assoclen ->  <- cryptlen ->
-		 *          <------- total_in ----------->
 		 *
-		 *  OUTPUT =   AssocData  ||  CipherText  ||   AuthTag
-		 *          <- assoclen ->  <- cryptlen ->  <- authsize ->
-		 *          <---------------- total_out ----------------->
+		 *  OUTPUT = AssocData    ||   CipherText   ||      AuthTag
+		 *          <- assoclen ->  <-- cryptlen -->  <- authsize ->
 		 *
 		 * Decryption case:
-		 *  INPUT  =   AssocData  ||  CipherText  ||  AuthTag
-		 *          <- assoclen ->  <--------- cryptlen --------->
-		 *                                          <- authsize ->
-		 *          <---------------- total_in ------------------>
+		 *  INPUT  =  AssocData     ||    CipherTex   ||       AuthTag
+		 *          <- assoclen --->  <---------- cryptlen ---------->
 		 *
-		 *  OUTPUT =   AssocData  ||   PlainText
-		 *          <- assoclen ->  <- crypten - authsize ->
-		 *          <---------- total_out ----------------->
+		 *  OUTPUT = AssocData    ||               PlainText
+		 *          <- assoclen ->  <- cryptlen - authsize ->
 		 */
 		cryp->areq = areq;
 		cryp->req = NULL;
 		cryp->authsize = crypto_aead_authsize(crypto_aead_reqtfm(areq));
-		cryp->total_in = areq->assoclen + areq->cryptlen;
-		if (is_encrypt(cryp))
-			/* Append auth tag to output */
-			cryp->total_out = cryp->total_in + cryp->authsize;
-		else
-			/* No auth tag in output */
-			cryp->total_out = cryp->total_in - cryp->authsize;
+		if (is_encrypt(cryp)) {
+			cryp->payload_in = areq->cryptlen;
+			cryp->header_in = areq->assoclen;
+			cryp->payload_out = areq->cryptlen;
+		} else {
+			cryp->payload_in = areq->cryptlen - cryp->authsize;
+			cryp->header_in = areq->assoclen;
+			cryp->payload_out = cryp->payload_in;
+		}
 	}
 
-	cryp->total_in_save = cryp->total_in;
-	cryp->total_out_save = cryp->total_out;
+	in_sg = req ? req->src : areq->src;
+	scatterwalk_start(&cryp->in_walk, in_sg);
 
-	cryp->in_sg = req ? req->src : areq->src;
 	cryp->out_sg = req ? req->dst : areq->dst;
-	cryp->out_sg_save = cryp->out_sg;
-
-	cryp->in_sg_len = sg_nents_for_len(cryp->in_sg, cryp->total_in);
-	if (cryp->in_sg_len < 0) {
-		dev_err(cryp->dev, "Cannot get in_sg_len\n");
-		ret = cryp->in_sg_len;
-		return ret;
-	}
-
-	cryp->out_sg_len = sg_nents_for_len(cryp->out_sg, cryp->total_out);
-	if (cryp->out_sg_len < 0) {
-		dev_err(cryp->dev, "Cannot get out_sg_len\n");
-		ret = cryp->out_sg_len;
-		return ret;
-	}
-
-	ret = stm32_cryp_copy_sgs(cryp);
-	if (ret)
-		return ret;
-
-	scatterwalk_start(&cryp->in_walk, cryp->in_sg);
 	scatterwalk_start(&cryp->out_walk, cryp->out_sg);
 
 	if (is_gcm(cryp) || is_ccm(cryp)) {
 		/* In output, jump after assoc data */
-		scatterwalk_advance(&cryp->out_walk, cryp->areq->assoclen);
-		cryp->total_out -= cryp->areq->assoclen;
+		scatterwalk_copychunks(NULL, &cryp->out_walk, cryp->areq->assoclen, 2);
 	}
 
+	if (is_ctr(cryp))
+		memset(cryp->last_ctr, 0, sizeof(cryp->last_ctr));
+
 	ret = stm32_cryp_hw_init(cryp);
 	return ret;
 }
@@ -1061,8 +1108,7 @@
 	if (!cryp)
 		return -ENODEV;
 
-	if (unlikely(!cryp->areq->assoclen &&
-		     !stm32_cryp_get_input_text_len(cryp))) {
+	if (unlikely(!cryp->payload_in && !cryp->header_in)) {
 		/* No input data to process: get tag and finish */
 		stm32_cryp_finish_req(cryp, 0);
 		return 0;
@@ -1071,43 +1117,10 @@
 	return stm32_cryp_cpu_start(cryp);
 }
 
-static u32 *stm32_cryp_next_out(struct stm32_cryp *cryp, u32 *dst,
-				unsigned int n)
-{
-	scatterwalk_advance(&cryp->out_walk, n);
-
-	if (unlikely(cryp->out_sg->length == _walked_out)) {
-		cryp->out_sg = sg_next(cryp->out_sg);
-		if (cryp->out_sg) {
-			scatterwalk_start(&cryp->out_walk, cryp->out_sg);
-			return (sg_virt(cryp->out_sg) + _walked_out);
-		}
-	}
-
-	return (u32 *)((u8 *)dst + n);
-}
-
-static u32 *stm32_cryp_next_in(struct stm32_cryp *cryp, u32 *src,
-			       unsigned int n)
-{
-	scatterwalk_advance(&cryp->in_walk, n);
-
-	if (unlikely(cryp->in_sg->length == _walked_in)) {
-		cryp->in_sg = sg_next(cryp->in_sg);
-		if (cryp->in_sg) {
-			scatterwalk_start(&cryp->in_walk, cryp->in_sg);
-			return (sg_virt(cryp->in_sg) + _walked_in);
-		}
-	}
-
-	return (u32 *)((u8 *)src + n);
-}
-
 static int stm32_cryp_read_auth_tag(struct stm32_cryp *cryp)
 {
-	u32 cfg, size_bit, *dst, d32;
-	u8 *d8;
-	unsigned int i, j;
+	u32 cfg, size_bit;
+	unsigned int i;
 	int ret = 0;
 
 	/* Update Config */
@@ -1130,7 +1143,7 @@
 		stm32_cryp_write(cryp, CRYP_DIN, size_bit);
 
 		size_bit = is_encrypt(cryp) ? cryp->areq->cryptlen :
-				cryp->areq->cryptlen - AES_BLOCK_SIZE;
+				cryp->areq->cryptlen - cryp->authsize;
 		size_bit *= 8;
 		if (cryp->caps->swap_final)
 			size_bit = (__force u32)cpu_to_be32(size_bit);
@@ -1139,11 +1152,9 @@
 		stm32_cryp_write(cryp, CRYP_DIN, size_bit);
 	} else {
 		/* CCM: write CTR0 */
-		u8 iv[AES_BLOCK_SIZE];
-		u32 *iv32 = (u32 *)iv;
-		__be32 *biv;
-
-		biv = (void *)iv;
+		u32 iv32[AES_BLOCK_32];
+		u8 *iv = (u8 *)iv32;
+		__be32 *biv = (__be32 *)iv32;
 
 		memcpy(iv, cryp->areq->iv, AES_BLOCK_SIZE);
 		memset(iv + AES_BLOCK_SIZE - 1 - iv[0], 0, iv[0] + 1);
@@ -1165,39 +1176,18 @@
 	}
 
 	if (is_encrypt(cryp)) {
+		u32 out_tag[AES_BLOCK_32];
+
 		/* Get and write tag */
-		dst = sg_virt(cryp->out_sg) + _walked_out;
+		for (i = 0; i < AES_BLOCK_32; i++)
+			out_tag[i] = stm32_cryp_read(cryp, CRYP_DOUT);
 
-		for (i = 0; i < AES_BLOCK_32; i++) {
-			if (cryp->total_out >= sizeof(u32)) {
-				/* Read a full u32 */
-				*dst = stm32_cryp_read(cryp, CRYP_DOUT);
-
-				dst = stm32_cryp_next_out(cryp, dst,
-							  sizeof(u32));
-				cryp->total_out -= sizeof(u32);
-			} else if (!cryp->total_out) {
-				/* Empty fifo out (data from input padding) */
-				stm32_cryp_read(cryp, CRYP_DOUT);
-			} else {
-				/* Read less than an u32 */
-				d32 = stm32_cryp_read(cryp, CRYP_DOUT);
-				d8 = (u8 *)&d32;
-
-				for (j = 0; j < cryp->total_out; j++) {
-					*((u8 *)dst) = *(d8++);
-					dst = stm32_cryp_next_out(cryp, dst, 1);
-				}
-				cryp->total_out = 0;
-			}
-		}
+		scatterwalk_copychunks(out_tag, &cryp->out_walk, cryp->authsize, 1);
 	} else {
 		/* Get and check tag */
 		u32 in_tag[AES_BLOCK_32], out_tag[AES_BLOCK_32];
 
-		scatterwalk_map_and_copy(in_tag, cryp->in_sg,
-					 cryp->total_in_save - cryp->authsize,
-					 cryp->authsize, 0);
+		scatterwalk_copychunks(in_tag, &cryp->in_walk, cryp->authsize, 0);
 
 		for (i = 0; i < AES_BLOCK_32; i++)
 			out_tag[i] = stm32_cryp_read(cryp, CRYP_DOUT);
@@ -1217,115 +1207,59 @@
 {
 	u32 cr;
 
-	if (unlikely(cryp->last_ctr[3] == 0xFFFFFFFF)) {
-		cryp->last_ctr[3] = 0;
-		cryp->last_ctr[2]++;
-		if (!cryp->last_ctr[2]) {
-			cryp->last_ctr[1]++;
-			if (!cryp->last_ctr[1])
-				cryp->last_ctr[0]++;
-		}
+	if (unlikely(cryp->last_ctr[3] == cpu_to_be32(0xFFFFFFFF))) {
+		/*
+		 * In this case, we need to increment manually the ctr counter,
+		 * as HW doesn't handle the U32 carry.
+		 */
+		crypto_inc((u8 *)cryp->last_ctr, sizeof(cryp->last_ctr));
 
 		cr = stm32_cryp_read(cryp, CRYP_CR);
 		stm32_cryp_write(cryp, CRYP_CR, cr & ~CR_CRYPEN);
 
-		stm32_cryp_hw_write_iv(cryp, (__be32 *)cryp->last_ctr);
+		stm32_cryp_hw_write_iv(cryp, cryp->last_ctr);
 
 		stm32_cryp_write(cryp, CRYP_CR, cr);
 	}
 
-	cryp->last_ctr[0] = stm32_cryp_read(cryp, CRYP_IV0LR);
-	cryp->last_ctr[1] = stm32_cryp_read(cryp, CRYP_IV0RR);
-	cryp->last_ctr[2] = stm32_cryp_read(cryp, CRYP_IV1LR);
-	cryp->last_ctr[3] = stm32_cryp_read(cryp, CRYP_IV1RR);
-}
-
-static bool stm32_cryp_irq_read_data(struct stm32_cryp *cryp)
-{
-	unsigned int i, j;
-	u32 d32, *dst;
-	u8 *d8;
-	size_t tag_size;
-
-	/* Do no read tag now (if any) */
-	if (is_encrypt(cryp) && (is_gcm(cryp) || is_ccm(cryp)))
-		tag_size = cryp->authsize;
-	else
-		tag_size = 0;
+	/* The IV registers are BE  */
+	cryp->last_ctr[0] = cpu_to_be32(stm32_cryp_read(cryp, CRYP_IV0LR));
+	cryp->last_ctr[1] = cpu_to_be32(stm32_cryp_read(cryp, CRYP_IV0RR));
+	cryp->last_ctr[2] = cpu_to_be32(stm32_cryp_read(cryp, CRYP_IV1LR));
+	cryp->last_ctr[3] = cpu_to_be32(stm32_cryp_read(cryp, CRYP_IV1RR));
+}
 
-	dst = sg_virt(cryp->out_sg) + _walked_out;
+static void stm32_cryp_irq_read_data(struct stm32_cryp *cryp)
+{
+	unsigned int i;
+	u32 block[AES_BLOCK_32];
 
-	for (i = 0; i < cryp->hw_blocksize / sizeof(u32); i++) {
-		if (likely(cryp->total_out - tag_size >= sizeof(u32))) {
-			/* Read a full u32 */
-			*dst = stm32_cryp_read(cryp, CRYP_DOUT);
-
-			dst = stm32_cryp_next_out(cryp, dst, sizeof(u32));
-			cryp->total_out -= sizeof(u32);
-		} else if (cryp->total_out == tag_size) {
-			/* Empty fifo out (data from input padding) */
-			d32 = stm32_cryp_read(cryp, CRYP_DOUT);
-		} else {
-			/* Read less than an u32 */
-			d32 = stm32_cryp_read(cryp, CRYP_DOUT);
-			d8 = (u8 *)&d32;
-
-			for (j = 0; j < cryp->total_out - tag_size; j++) {
-				*((u8 *)dst) = *(d8++);
-				dst = stm32_cryp_next_out(cryp, dst, 1);
-			}
-			cryp->total_out = tag_size;
-		}
-	}
+	for (i = 0; i < cryp->hw_blocksize / sizeof(u32); i++)
+		block[i] = stm32_cryp_read(cryp, CRYP_DOUT);
 
-	return !(cryp->total_out - tag_size) || !cryp->total_in;
+	scatterwalk_copychunks(block, &cryp->out_walk, min_t(size_t, cryp->hw_blocksize,
+							     cryp->payload_out), 1);
+	cryp->payload_out -= min_t(size_t, cryp->hw_blocksize,
+				   cryp->payload_out);
 }
 
 static void stm32_cryp_irq_write_block(struct stm32_cryp *cryp)
 {
-	unsigned int i, j;
-	u32 *src;
-	u8 d8[4];
-	size_t tag_size;
-
-	/* Do no write tag (if any) */
-	if (is_decrypt(cryp) && (is_gcm(cryp) || is_ccm(cryp)))
-		tag_size = cryp->authsize;
-	else
-		tag_size = 0;
-
-	src = sg_virt(cryp->in_sg) + _walked_in;
+	unsigned int i;
+	u32 block[AES_BLOCK_32] = {0};
 
-	for (i = 0; i < cryp->hw_blocksize / sizeof(u32); i++) {
-		if (likely(cryp->total_in - tag_size >= sizeof(u32))) {
-			/* Write a full u32 */
-			stm32_cryp_write(cryp, CRYP_DIN, *src);
-
-			src = stm32_cryp_next_in(cryp, src, sizeof(u32));
-			cryp->total_in -= sizeof(u32);
-		} else if (cryp->total_in == tag_size) {
-			/* Write padding data */
-			stm32_cryp_write(cryp, CRYP_DIN, 0);
-		} else {
-			/* Write less than an u32 */
-			memset(d8, 0, sizeof(u32));
-			for (j = 0; j < cryp->total_in - tag_size; j++) {
-				d8[j] = *((u8 *)src);
-				src = stm32_cryp_next_in(cryp, src, 1);
-			}
+	scatterwalk_copychunks(block, &cryp->in_walk, min_t(size_t, cryp->hw_blocksize,
+							    cryp->payload_in), 0);
+	for (i = 0; i < cryp->hw_blocksize / sizeof(u32); i++)
+		stm32_cryp_write(cryp, CRYP_DIN, block[i]);
 
-			stm32_cryp_write(cryp, CRYP_DIN, *(u32 *)d8);
-			cryp->total_in = tag_size;
-		}
-	}
+	cryp->payload_in -= min_t(size_t, cryp->hw_blocksize, cryp->payload_in);
 }
 
 static void stm32_cryp_irq_write_gcm_padded_data(struct stm32_cryp *cryp)
 {
 	int err;
-	u32 cfg, tmp[AES_BLOCK_32];
-	size_t total_in_ori = cryp->total_in;
-	struct scatterlist *out_sg_ori = cryp->out_sg;
+	u32 cfg, block[AES_BLOCK_32] = {0};
 	unsigned int i;
 
 	/* 'Special workaround' procedure described in the datasheet */
@@ -1350,18 +1284,25 @@
 
 	/* b) pad and write the last block */
 	stm32_cryp_irq_write_block(cryp);
-	cryp->total_in = total_in_ori;
+	/* wait end of process */
 	err = stm32_cryp_wait_output(cryp);
 	if (err) {
-		dev_err(cryp->dev, "Timeout (write gcm header)\n");
+		dev_err(cryp->dev, "Timeout (write gcm last data)\n");
 		return stm32_cryp_finish_req(cryp, err);
 	}
 
 	/* c) get and store encrypted data */
-	stm32_cryp_irq_read_data(cryp);
-	scatterwalk_map_and_copy(tmp, out_sg_ori,
-				 cryp->total_in_save - total_in_ori,
-				 total_in_ori, 0);
+	/*
+	 * Same code as stm32_cryp_irq_read_data(), but we want to store
+	 * block value
+	 */
+	for (i = 0; i < cryp->hw_blocksize / sizeof(u32); i++)
+		block[i] = stm32_cryp_read(cryp, CRYP_DOUT);
+
+	scatterwalk_copychunks(block, &cryp->out_walk, min_t(size_t, cryp->hw_blocksize,
+							     cryp->payload_out), 1);
+	cryp->payload_out -= min_t(size_t, cryp->hw_blocksize,
+				   cryp->payload_out);
 
 	/* d) change mode back to AES GCM */
 	cfg &= ~CR_ALGO_MASK;
@@ -1374,19 +1315,13 @@
 	stm32_cryp_write(cryp, CRYP_CR, cfg);
 
 	/* f) write padded data */
-	for (i = 0; i < AES_BLOCK_32; i++) {
-		if (cryp->total_in)
-			stm32_cryp_write(cryp, CRYP_DIN, tmp[i]);
-		else
-			stm32_cryp_write(cryp, CRYP_DIN, 0);
-
-		cryp->total_in -= min_t(size_t, sizeof(u32), cryp->total_in);
-	}
+	for (i = 0; i < AES_BLOCK_32; i++)
+		stm32_cryp_write(cryp, CRYP_DIN, block[i]);
 
 	/* g) Empty fifo out */
 	err = stm32_cryp_wait_output(cryp);
 	if (err) {
-		dev_err(cryp->dev, "Timeout (write gcm header)\n");
+		dev_err(cryp->dev, "Timeout (write gcm padded data)\n");
 		return stm32_cryp_finish_req(cryp, err);
 	}
 
@@ -1399,16 +1334,14 @@
 
 static void stm32_cryp_irq_set_npblb(struct stm32_cryp *cryp)
 {
-	u32 cfg, payload_bytes;
+	u32 cfg;
 
 	/* disable ip, set NPBLB and reneable ip */
 	cfg = stm32_cryp_read(cryp, CRYP_CR);
 	cfg &= ~CR_CRYPEN;
 	stm32_cryp_write(cryp, CRYP_CR, cfg);
 
-	payload_bytes = is_decrypt(cryp) ? cryp->total_in - cryp->authsize :
-					   cryp->total_in;
-	cfg |= (cryp->hw_blocksize - payload_bytes) << CR_NBPBL_SHIFT;
+	cfg |= (cryp->hw_blocksize - cryp->payload_in) << CR_NBPBL_SHIFT;
 	cfg |= CR_CRYPEN;
 	stm32_cryp_write(cryp, CRYP_CR, cfg);
 }
@@ -1417,13 +1350,11 @@
 {
 	int err = 0;
 	u32 cfg, iv1tmp;
-	u32 cstmp1[AES_BLOCK_32], cstmp2[AES_BLOCK_32], tmp[AES_BLOCK_32];
-	size_t last_total_out, total_in_ori = cryp->total_in;
-	struct scatterlist *out_sg_ori = cryp->out_sg;
+	u32 cstmp1[AES_BLOCK_32], cstmp2[AES_BLOCK_32];
+	u32 block[AES_BLOCK_32] = {0};
 	unsigned int i;
 
 	/* 'Special workaround' procedure described in the datasheet */
-	cryp->flags |= FLG_CCM_PADDED_WA;
 
 	/* a) disable ip */
 	stm32_cryp_write(cryp, CRYP_IMSCR, 0);
@@ -1453,7 +1384,7 @@
 
 	/* b) pad and write the last block */
 	stm32_cryp_irq_write_block(cryp);
-	cryp->total_in = total_in_ori;
+	/* wait end of process */
 	err = stm32_cryp_wait_output(cryp);
 	if (err) {
 		dev_err(cryp->dev, "Timeout (wite ccm padded data)\n");
@@ -1461,13 +1392,16 @@
 	}
 
 	/* c) get and store decrypted data */
-	last_total_out = cryp->total_out;
-	stm32_cryp_irq_read_data(cryp);
-
-	memset(tmp, 0, sizeof(tmp));
-	scatterwalk_map_and_copy(tmp, out_sg_ori,
-				 cryp->total_out_save - last_total_out,
-				 last_total_out, 0);
+	/*
+	 * Same code as stm32_cryp_irq_read_data(), but we want to store
+	 * block value
+	 */
+	for (i = 0; i < cryp->hw_blocksize / sizeof(u32); i++)
+		block[i] = stm32_cryp_read(cryp, CRYP_DOUT);
+
+	scatterwalk_copychunks(block, &cryp->out_walk, min_t(size_t, cryp->hw_blocksize,
+							     cryp->payload_out), 1);
+	cryp->payload_out -= min_t(size_t, cryp->hw_blocksize, cryp->payload_out);
 
 	/* d) Load again CRYP_CSGCMCCMxR */
 	for (i = 0; i < ARRAY_SIZE(cstmp2); i++)
@@ -1484,10 +1418,10 @@
 	stm32_cryp_write(cryp, CRYP_CR, cfg);
 
 	/* g) XOR and write padded data */
-	for (i = 0; i < ARRAY_SIZE(tmp); i++) {
-		tmp[i] ^= cstmp1[i];
-		tmp[i] ^= cstmp2[i];
-		stm32_cryp_write(cryp, CRYP_DIN, tmp[i]);
+	for (i = 0; i < ARRAY_SIZE(block); i++) {
+		block[i] ^= cstmp1[i];
+		block[i] ^= cstmp2[i];
+		stm32_cryp_write(cryp, CRYP_DIN, block[i]);
 	}
 
 	/* h) wait for completion */
@@ -1501,30 +1435,34 @@
 
 static void stm32_cryp_irq_write_data(struct stm32_cryp *cryp)
 {
-	if (unlikely(!cryp->total_in)) {
+	if (unlikely(!cryp->payload_in)) {
 		dev_warn(cryp->dev, "No more data to process\n");
 		return;
 	}
 
-	if (unlikely(cryp->total_in < AES_BLOCK_SIZE &&
+	if (unlikely(cryp->payload_in < AES_BLOCK_SIZE &&
 		     (stm32_cryp_get_hw_mode(cryp) == CR_AES_GCM) &&
 		     is_encrypt(cryp))) {
 		/* Padding for AES GCM encryption */
-		if (cryp->caps->padding_wa)
+		if (cryp->caps->padding_wa) {
 			/* Special case 1 */
-			return stm32_cryp_irq_write_gcm_padded_data(cryp);
+			stm32_cryp_irq_write_gcm_padded_data(cryp);
+			return;
+		}
 
 		/* Setting padding bytes (NBBLB) */
 		stm32_cryp_irq_set_npblb(cryp);
 	}
 
-	if (unlikely((cryp->total_in - cryp->authsize < AES_BLOCK_SIZE) &&
+	if (unlikely((cryp->payload_in < AES_BLOCK_SIZE) &&
 		     (stm32_cryp_get_hw_mode(cryp) == CR_AES_CCM) &&
 		     is_decrypt(cryp))) {
 		/* Padding for AES CCM decryption */
-		if (cryp->caps->padding_wa)
+		if (cryp->caps->padding_wa) {
 			/* Special case 2 */
-			return stm32_cryp_irq_write_ccm_padded_data(cryp);
+			stm32_cryp_irq_write_ccm_padded_data(cryp);
+			return;
+		}
 
 		/* Setting padding bytes (NBBLB) */
 		stm32_cryp_irq_set_npblb(cryp);
@@ -1536,192 +1474,60 @@
 	stm32_cryp_irq_write_block(cryp);
 }
 
-static void stm32_cryp_irq_write_gcm_header(struct stm32_cryp *cryp)
+static void stm32_cryp_irq_write_gcmccm_header(struct stm32_cryp *cryp)
 {
-	int err;
-	unsigned int i, j;
-	u32 cfg, *src;
-
-	src = sg_virt(cryp->in_sg) + _walked_in;
-
-	for (i = 0; i < AES_BLOCK_32; i++) {
-		stm32_cryp_write(cryp, CRYP_DIN, *src);
-
-		src = stm32_cryp_next_in(cryp, src, sizeof(u32));
-		cryp->total_in -= min_t(size_t, sizeof(u32), cryp->total_in);
-
-		/* Check if whole header written */
-		if ((cryp->total_in_save - cryp->total_in) ==
-				cryp->areq->assoclen) {
-			/* Write padding if needed */
-			for (j = i + 1; j < AES_BLOCK_32; j++)
-				stm32_cryp_write(cryp, CRYP_DIN, 0);
-
-			/* Wait for completion */
-			err = stm32_cryp_wait_busy(cryp);
-			if (err) {
-				dev_err(cryp->dev, "Timeout (gcm header)\n");
-				return stm32_cryp_finish_req(cryp, err);
-			}
-
-			if (stm32_cryp_get_input_text_len(cryp)) {
-				/* Phase 3 : payload */
-				cfg = stm32_cryp_read(cryp, CRYP_CR);
-				cfg &= ~CR_CRYPEN;
-				stm32_cryp_write(cryp, CRYP_CR, cfg);
-
-				cfg &= ~CR_PH_MASK;
-				cfg |= CR_PH_PAYLOAD;
-				cfg |= CR_CRYPEN;
-				stm32_cryp_write(cryp, CRYP_CR, cfg);
-			} else {
-				/* Phase 4 : tag */
-				stm32_cryp_write(cryp, CRYP_IMSCR, 0);
-				stm32_cryp_finish_req(cryp, 0);
-			}
-
-			break;
-		}
-
-		if (!cryp->total_in)
-			break;
-	}
-}
-
-static void stm32_cryp_irq_write_ccm_header(struct stm32_cryp *cryp)
-{
-	int err;
-	unsigned int i = 0, j, k;
-	u32 alen, cfg, *src;
-	u8 d8[4];
-
-	src = sg_virt(cryp->in_sg) + _walked_in;
-	alen = cryp->areq->assoclen;
-
-	if (!_walked_in) {
-		if (cryp->areq->assoclen <= 65280) {
-			/* Write first u32 of B1 */
-			d8[0] = (alen >> 8) & 0xFF;
-			d8[1] = alen & 0xFF;
-			d8[2] = *((u8 *)src);
-			src = stm32_cryp_next_in(cryp, src, 1);
-			d8[3] = *((u8 *)src);
-			src = stm32_cryp_next_in(cryp, src, 1);
-
-			stm32_cryp_write(cryp, CRYP_DIN, *(u32 *)d8);
-			i++;
-
-			cryp->total_in -= min_t(size_t, 2, cryp->total_in);
-		} else {
-			/* Build the two first u32 of B1 */
-			d8[0] = 0xFF;
-			d8[1] = 0xFE;
-			d8[2] = alen & 0xFF000000;
-			d8[3] = alen & 0x00FF0000;
-
-			stm32_cryp_write(cryp, CRYP_DIN, *(u32 *)d8);
-			i++;
-
-			d8[0] = alen & 0x0000FF00;
-			d8[1] = alen & 0x000000FF;
-			d8[2] = *((u8 *)src);
-			src = stm32_cryp_next_in(cryp, src, 1);
-			d8[3] = *((u8 *)src);
-			src = stm32_cryp_next_in(cryp, src, 1);
-
-			stm32_cryp_write(cryp, CRYP_DIN, *(u32 *)d8);
-			i++;
-
-			cryp->total_in -= min_t(size_t, 2, cryp->total_in);
-		}
-	}
+	unsigned int i;
+	u32 block[AES_BLOCK_32] = {0};
+	size_t written;
 
-	/* Write next u32 */
-	for (; i < AES_BLOCK_32; i++) {
-		/* Build an u32 */
-		memset(d8, 0, sizeof(u32));
-		for (k = 0; k < sizeof(u32); k++) {
-			d8[k] = *((u8 *)src);
-			src = stm32_cryp_next_in(cryp, src, 1);
-
-			cryp->total_in -= min_t(size_t, 1, cryp->total_in);
-			if ((cryp->total_in_save - cryp->total_in) == alen)
-				break;
-		}
+	written = min_t(size_t, AES_BLOCK_SIZE, cryp->header_in);
 
-		stm32_cryp_write(cryp, CRYP_DIN, *(u32 *)d8);
+	scatterwalk_copychunks(block, &cryp->in_walk, written, 0);
+	for (i = 0; i < AES_BLOCK_32; i++)
+		stm32_cryp_write(cryp, CRYP_DIN, block[i]);
 
-		if ((cryp->total_in_save - cryp->total_in) == alen) {
-			/* Write padding if needed */
-			for (j = i + 1; j < AES_BLOCK_32; j++)
-				stm32_cryp_write(cryp, CRYP_DIN, 0);
-
-			/* Wait for completion */
-			err = stm32_cryp_wait_busy(cryp);
-			if (err) {
-				dev_err(cryp->dev, "Timeout (ccm header)\n");
-				return stm32_cryp_finish_req(cryp, err);
-			}
-
-			if (stm32_cryp_get_input_text_len(cryp)) {
-				/* Phase 3 : payload */
-				cfg = stm32_cryp_read(cryp, CRYP_CR);
-				cfg &= ~CR_CRYPEN;
-				stm32_cryp_write(cryp, CRYP_CR, cfg);
-
-				cfg &= ~CR_PH_MASK;
-				cfg |= CR_PH_PAYLOAD;
-				cfg |= CR_CRYPEN;
-				stm32_cryp_write(cryp, CRYP_CR, cfg);
-			} else {
-				/* Phase 4 : tag */
-				stm32_cryp_write(cryp, CRYP_IMSCR, 0);
-				stm32_cryp_finish_req(cryp, 0);
-			}
+	cryp->header_in -= written;
 
-			break;
-		}
-	}
+	stm32_crypt_gcmccm_end_header(cryp);
 }
 
 static irqreturn_t stm32_cryp_irq_thread(int irq, void *arg)
 {
 	struct stm32_cryp *cryp = arg;
 	u32 ph;
+	u32 it_mask = stm32_cryp_read(cryp, CRYP_IMSCR);
 
 	if (cryp->irq_status & MISR_OUT)
 		/* Output FIFO IRQ: read data */
-		if (unlikely(stm32_cryp_irq_read_data(cryp))) {
-			/* All bytes processed, finish */
-			stm32_cryp_write(cryp, CRYP_IMSCR, 0);
-			stm32_cryp_finish_req(cryp, 0);
-			return IRQ_HANDLED;
-		}
+		stm32_cryp_irq_read_data(cryp);
 
 	if (cryp->irq_status & MISR_IN) {
-		if (is_gcm(cryp)) {
+		if (is_gcm(cryp) || is_ccm(cryp)) {
 			ph = stm32_cryp_read(cryp, CRYP_CR) & CR_PH_MASK;
 			if (unlikely(ph == CR_PH_HEADER))
 				/* Write Header */
-				stm32_cryp_irq_write_gcm_header(cryp);
-			else
-				/* Input FIFO IRQ: write data */
-				stm32_cryp_irq_write_data(cryp);
-			cryp->gcm_ctr++;
-		} else if (is_ccm(cryp)) {
-			ph = stm32_cryp_read(cryp, CRYP_CR) & CR_PH_MASK;
-			if (unlikely(ph == CR_PH_HEADER))
-				/* Write Header */
-				stm32_cryp_irq_write_ccm_header(cryp);
+				stm32_cryp_irq_write_gcmccm_header(cryp);
 			else
 				/* Input FIFO IRQ: write data */
 				stm32_cryp_irq_write_data(cryp);
+			if (is_gcm(cryp))
+				cryp->gcm_ctr++;
 		} else {
 			/* Input FIFO IRQ: write data */
 			stm32_cryp_irq_write_data(cryp);
 		}
 	}
 
+	/* Mask useless interrupts */
+	if (!cryp->payload_in && !cryp->header_in)
+		it_mask &= ~IMSCR_IN;
+	if (!cryp->payload_out)
+		it_mask &= ~IMSCR_OUT;
+	stm32_cryp_write(cryp, CRYP_IMSCR, it_mask);
+
+	if (!cryp->payload_in && !cryp->header_in && !cryp->payload_out)
+		stm32_cryp_finish_req(cryp, 0);
+
 	return IRQ_HANDLED;
 }
 
@@ -1742,7 +1548,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= AES_BLOCK_SIZE,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1759,7 +1565,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= AES_BLOCK_SIZE,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1777,7 +1583,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= 1,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1795,7 +1601,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= DES_BLOCK_SIZE,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1812,7 +1618,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= DES_BLOCK_SIZE,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1830,7 +1636,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= DES_BLOCK_SIZE,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1847,7 +1653,7 @@
 	.base.cra_flags		= CRYPTO_ALG_ASYNC,
 	.base.cra_blocksize	= DES_BLOCK_SIZE,
 	.base.cra_ctxsize	= sizeof(struct stm32_cryp_ctx),
-	.base.cra_alignmask	= 0xf,
+	.base.cra_alignmask	= 0,
 	.base.cra_module	= THIS_MODULE,
 
 	.init			= stm32_cryp_init_tfm,
@@ -1877,7 +1683,7 @@
 		.cra_flags		= CRYPTO_ALG_ASYNC,
 		.cra_blocksize		= 1,
 		.cra_ctxsize		= sizeof(struct stm32_cryp_ctx),
-		.cra_alignmask		= 0xf,
+		.cra_alignmask		= 0,
 		.cra_module		= THIS_MODULE,
 	},
 },
@@ -1897,7 +1703,7 @@
 		.cra_flags		= CRYPTO_ALG_ASYNC,
 		.cra_blocksize		= 1,
 		.cra_ctxsize		= sizeof(struct stm32_cryp_ctx),
-		.cra_alignmask		= 0xf,
+		.cra_alignmask		= 0,
 		.cra_module		= THIS_MODULE,
 	},
 },
@@ -2027,8 +1833,6 @@
 
 	pm_runtime_disable(dev);
 	pm_runtime_put_noidle(dev);
-	pm_runtime_disable(dev);
-	pm_runtime_put_noidle(dev);
 
 	clk_disable_unprepare(cryp->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/stm32/stm32-hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/stm32/stm32-hash.c
@@ -565,9 +565,9 @@
 	}
 
 	for_each_sg(rctx->sg, tsg, rctx->nents, i) {
+		sg[0] = *tsg;
 		len = sg->length;
 
-		sg[0] = *tsg;
 		if (sg_is_last(sg)) {
 			if (hdev->dma_mode == 1) {
 				len = (ALIGN(sg->length, 16) - 16);
@@ -813,7 +813,7 @@
 static int stm32_hash_hw_init(struct stm32_hash_dev *hdev,
 			      struct stm32_hash_request_ctx *rctx)
 {
-	pm_runtime_resume_and_get(hdev->dev);
+	pm_runtime_get_sync(hdev->dev);
 
 	if (!(HASH_FLAGS_INIT & hdev->flags)) {
 		stm32_hash_write(hdev, HASH_CR, HASH_CR_INIT);
@@ -962,7 +962,7 @@
 	u32 *preg;
 	unsigned int i;
 
-	pm_runtime_resume_and_get(hdev->dev);
+	pm_runtime_get_sync(hdev->dev);
 
 	while ((stm32_hash_read(hdev, HASH_SR) & HASH_SR_BUSY))
 		cpu_relax();
@@ -1000,7 +1000,7 @@
 
 	preg = rctx->hw_context;
 
-	pm_runtime_resume_and_get(hdev->dev);
+	pm_runtime_get_sync(hdev->dev);
 
 	stm32_hash_write(hdev, HASH_IMR, *preg++);
 	stm32_hash_write(hdev, HASH_STR, *preg++);
@@ -1566,9 +1566,7 @@
 	if (!hdev)
 		return -ENODEV;
 
-	ret = pm_runtime_resume_and_get(hdev->dev);
-	if (ret < 0)
-		return ret;
+	ret = pm_runtime_get_sync(hdev->dev);
 
 	stm32_hash_unregister_algs(hdev);
 
@@ -1584,7 +1582,8 @@
 	pm_runtime_disable(hdev->dev);
 	pm_runtime_put_noidle(hdev->dev);
 
-	clk_disable_unprepare(hdev->clk);
+	if (ret >= 0)
+		clk_disable_unprepare(hdev->clk);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/virtio/virtio_crypto_algs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/virtio/virtio_crypto_algs.c
@@ -255,7 +255,7 @@
 			vcrypto->ctrl_status.status,
 			destroy_session->session_id);
 
-		return -EINVAL;
+		err = -EINVAL;
 	}
 	spin_unlock(&vcrypto->ctrl_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/virtio/virtio_crypto_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/virtio/virtio_crypto_common.h
@@ -10,6 +10,7 @@
 #include <linux/virtio.h>
 #include <linux/crypto.h>
 #include <linux/spinlock.h>
+#include <linux/interrupt.h>
 #include <crypto/aead.h>
 #include <crypto/aes.h>
 #include <crypto/engine.h>
@@ -27,6 +28,7 @@
 	char name[32];
 
 	struct crypto_engine *engine;
+	struct tasklet_struct done_task;
 };
 
 struct virtio_crypto {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/virtio/virtio_crypto_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/virtio/virtio_crypto_core.c
@@ -22,27 +22,28 @@
 	}
 }
 
-static void virtcrypto_dataq_callback(struct virtqueue *vq)
+static void virtcrypto_done_task(unsigned long data)
 {
-	struct virtio_crypto *vcrypto = vq->vdev->priv;
+	struct data_queue *data_vq = (struct data_queue *)data;
+	struct virtqueue *vq = data_vq->vq;
 	struct virtio_crypto_request *vc_req;
-	unsigned long flags;
 	unsigned int len;
-	unsigned int qid = vq->index;
 
-	spin_lock_irqsave(&vcrypto->data_vq[qid].lock, flags);
 	do {
 		virtqueue_disable_cb(vq);
 		while ((vc_req = virtqueue_get_buf(vq, &len)) != NULL) {
-			spin_unlock_irqrestore(
-				&vcrypto->data_vq[qid].lock, flags);
 			if (vc_req->alg_cb)
 				vc_req->alg_cb(vc_req, len);
-			spin_lock_irqsave(
-				&vcrypto->data_vq[qid].lock, flags);
 		}
 	} while (!virtqueue_enable_cb(vq));
-	spin_unlock_irqrestore(&vcrypto->data_vq[qid].lock, flags);
+}
+
+static void virtcrypto_dataq_callback(struct virtqueue *vq)
+{
+	struct virtio_crypto *vcrypto = vq->vdev->priv;
+	struct data_queue *dq = &vcrypto->data_vq[vq->index];
+
+	tasklet_schedule(&dq->done_task);
 }
 
 static int virtcrypto_find_vqs(struct virtio_crypto *vi)
@@ -99,6 +100,8 @@
 			ret = -ENOMEM;
 			goto err_engine;
 		}
+		tasklet_init(&vi->data_vq[i].done_task, virtcrypto_done_task,
+				(unsigned long)&vi->data_vq[i]);
 	}
 
 	kfree(names);
@@ -431,11 +434,14 @@
 static void virtcrypto_remove(struct virtio_device *vdev)
 {
 	struct virtio_crypto *vcrypto = vdev->priv;
+	int i;
 
 	dev_info(&vdev->dev, "Start virtcrypto_remove.\n");
 
 	if (virtcrypto_dev_started(vcrypto))
 		virtcrypto_dev_stop(vcrypto);
+	for (i = 0; i < vcrypto->max_data_queues; i++)
+		tasklet_kill(&vcrypto->data_vq[i].done_task);
 	vdev->config->reset(vdev);
 	virtcrypto_free_unused_reqs(vcrypto);
 	virtcrypto_clear_crypto_engines(vcrypto);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/vmx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/vmx/Kconfig
@@ -2,7 +2,11 @@
 config CRYPTO_DEV_VMX_ENCRYPT
 	tristate "Encryption acceleration support on P8 CPU"
 	depends on CRYPTO_DEV_VMX
+	select CRYPTO_AES
+	select CRYPTO_CBC
+	select CRYPTO_CTR
 	select CRYPTO_GHASH
+	select CRYPTO_XTS
 	default m
 	help
 	  Support for VMX cryptographic acceleration instructions on Power8 CPU.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/xilinx/Makefile
@@ -1,2 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_AES) += zynqmp-aes-gcm.o
+obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_AES_SKCIPHER) += zynqmp-aes.o
+obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_KECCAK_384) += zynqmp-sha-deprecated.o
+obj-$(CONFIG_CRYPTO_DEV_ZYNQMP_SHA3) += zynqmp-sha.o
+obj-$(CONFIG_CRYPTO_DEV_XILINX_RSA) += zynqmp-rsa.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/xilinx/zynqmp-aes-gcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/xilinx/zynqmp-aes-gcm.c
@@ -231,7 +231,10 @@
 		err = zynqmp_aes_aead_cipher(areq);
 	}
 
+	local_bh_disable();
 	crypto_finalize_aead_request(engine, areq, err);
+	local_bh_enable();
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/xilinx/zynqmp-aes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/xilinx/zynqmp-aes.c
@@ -0,0 +1,284 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx ZynqMP AES Driver.
+ * Copyright (c) 2018 Xilinx Inc.
+ */
+
+#include <crypto/aes.h>
+#include <crypto/internal/skcipher.h>
+#include <crypto/scatterwalk.h>
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/scatterlist.h>
+#include <linux/spinlock.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define ZYNQMP_AES_QUEUE_LENGTH			1
+#define ZYNQMP_AES_IV_SIZE			12
+#define ZYNQMP_AES_GCM_SIZE			16
+#define ZYNQMP_AES_KEY_SIZE			32
+
+#define ZYNQMP_AES_DECRYPT			0
+#define ZYNQMP_AES_ENCRYPT			1
+
+#define ZYNQMP_AES_KUP_KEY			0
+
+#define ZYNQMP_AES_GCM_TAG_MISMATCH_ERR		0x01
+#define ZYNQMP_AES_SIZE_ERR			0x06
+#define ZYNQMP_AES_WRONG_KEY_SRC_ERR		0x13
+#define ZYNQMP_AES_PUF_NOT_PROGRAMMED		0xE300
+
+#define ZYNQMP_AES_BLOCKSIZE			0x04
+
+#define ZYNQMP_KEY_SRC_SEL_KEY_LEN		1U
+
+struct zynqmp_aes_dev *aes_dd;
+
+struct zynqmp_aes_op {
+	struct zynqmp_aes_dev *dd;
+	void *src;
+	void *dst;
+	int len;
+	u8 key[ZYNQMP_AES_KEY_SIZE];
+	u8 *iv;
+	u32 keylen;
+	u32 keytype;
+};
+
+struct zynqmp_aes_dev {
+	struct device	*dev;
+};
+
+struct zynqmp_aes_data {
+	u64 src;
+	u64 iv;
+	u64 key;
+	u64 dst;
+	u64 size;
+	u64 optype;
+	u64 keysrc;
+};
+
+static struct zynqmp_aes_dev *zynqmp_aes_find_dev(struct zynqmp_aes_op *ctx)
+{
+	struct zynqmp_aes_dev *dd = aes_dd;
+
+	if (!ctx->dd)
+		ctx->dd = dd;
+	else
+		dd = ctx->dd;
+
+	return dd;
+}
+
+static int zynqmp_setkey_blk(struct crypto_skcipher *tfm, const u8 *key,
+			     unsigned int len)
+{
+	struct zynqmp_aes_op *op = crypto_skcipher_ctx(tfm);
+
+	if (len == ZYNQMP_KEY_SRC_SEL_KEY_LEN) {
+		op->keytype = *key;
+	} else {
+		op->keylen = len;
+		if (len == ZYNQMP_AES_KEY_SIZE) {
+			op->keytype = ZYNQMP_AES_KUP_KEY;
+			memcpy(op->key, key, len);
+		}
+	}
+
+	return 0;
+}
+
+static int zynqmp_aes_xcrypt(struct skcipher_request *req, unsigned int flags)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct zynqmp_aes_op *op = crypto_skcipher_ctx(tfm);
+	struct zynqmp_aes_dev *dd = zynqmp_aes_find_dev(op);
+	int err, ret, src_data = 0, dst_data = 0;
+	dma_addr_t dma_addr, dma_addr_buf;
+	struct zynqmp_aes_data *abuf;
+	struct skcipher_walk walk = {0};
+	unsigned int data_size;
+	size_t dma_size;
+	char *kbuf;
+
+	if (op->keytype == ZYNQMP_AES_KUP_KEY)
+		dma_size = req->cryptlen + ZYNQMP_AES_IV_SIZE + ZYNQMP_AES_KEY_SIZE;
+	else
+		dma_size = req->cryptlen + ZYNQMP_AES_IV_SIZE;
+
+	kbuf = dma_alloc_coherent(dd->dev, dma_size, &dma_addr, GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	abuf = dma_alloc_coherent(dd->dev, sizeof(struct zynqmp_aes_data),
+				  &dma_addr_buf, GFP_KERNEL);
+	if (!abuf) {
+		dma_free_coherent(dd->dev, dma_size, kbuf, dma_addr);
+		return -ENOMEM;
+	}
+
+	err = skcipher_walk_virt(&walk, req, false);
+	if (err)
+		goto END;
+	op->iv = walk.iv;
+
+	while ((data_size = walk.nbytes)) {
+		op->src = walk.src.virt.addr;
+		memcpy(kbuf + src_data, op->src, data_size);
+		src_data = src_data + data_size;
+		err = skcipher_walk_done(&walk, 0);
+		if (err)
+			goto END;
+	}
+	memcpy(kbuf + req->cryptlen, op->iv, ZYNQMP_AES_IV_SIZE);
+	abuf->src = dma_addr;
+	abuf->dst = dma_addr;
+	abuf->iv = abuf->src + req->cryptlen;
+	abuf->size = req->cryptlen - ZYNQMP_AES_GCM_SIZE;
+	abuf->optype = flags;
+	abuf->keysrc = op->keytype;
+
+	if (op->keytype == ZYNQMP_AES_KUP_KEY) {
+		memcpy(kbuf + req->cryptlen + ZYNQMP_AES_IV_SIZE,
+		       op->key, ZYNQMP_AES_KEY_SIZE);
+
+		abuf->key = abuf->src + req->cryptlen + ZYNQMP_AES_IV_SIZE;
+	} else {
+		abuf->key = 0;
+	}
+
+	zynqmp_pm_aes_engine(dma_addr_buf, (u32 *)&ret);
+
+	if (ret != 0) {
+		switch (ret) {
+		case ZYNQMP_AES_GCM_TAG_MISMATCH_ERR:
+			dev_err(dd->dev, "ERROR: Gcm Tag mismatch\n");
+			break;
+		case ZYNQMP_AES_SIZE_ERR:
+			dev_err(dd->dev, "ERROR : Non word aligned data\n");
+			break;
+		case ZYNQMP_AES_WRONG_KEY_SRC_ERR:
+			dev_err(dd->dev, "ERROR: Wrong KeySrc, enable secure mode\n");
+			break;
+		case ZYNQMP_AES_PUF_NOT_PROGRAMMED:
+			dev_err(dd->dev, "ERROR: PUF is not registered\n");
+			break;
+		default:
+			dev_err(dd->dev, "ERROR: Invalid\n");
+			break;
+		}
+		goto END;
+	}
+	if (!flags)
+		req->cryptlen = req->cryptlen - ZYNQMP_AES_GCM_SIZE;
+
+	err = skcipher_walk_virt(&walk, req, false);
+	if (err)
+		goto END;
+
+	while ((data_size = walk.nbytes)) {
+		memcpy(walk.dst.virt.addr, kbuf + dst_data, data_size);
+		dst_data = dst_data + data_size;
+		err = skcipher_walk_done(&walk, 0);
+		if (err)
+			goto END;
+	}
+END:
+	dma_free_coherent(dd->dev, dma_size, kbuf, dma_addr);
+	dma_free_coherent(dd->dev, sizeof(struct zynqmp_aes_data),
+			  abuf, dma_addr_buf);
+	return err;
+}
+
+static int zynqmp_aes_decrypt(struct skcipher_request *req)
+{
+	return zynqmp_aes_xcrypt(req, ZYNQMP_AES_DECRYPT);
+}
+
+static int zynqmp_aes_encrypt(struct skcipher_request *req)
+{
+	return zynqmp_aes_xcrypt(req, ZYNQMP_AES_ENCRYPT);
+}
+
+static struct skcipher_alg zynqmp_alg = {
+	.base.cra_name		=	"xilinx-zynqmp-aes",
+	.base.cra_driver_name	=	"zynqmp-aes",
+	.base.cra_priority	=	400,
+	.base.cra_flags		=	CRYPTO_ALG_TYPE_SKCIPHER |
+					CRYPTO_ALG_KERN_DRIVER_ONLY,
+	.base.cra_blocksize	=	ZYNQMP_AES_BLOCKSIZE,
+	.base.cra_ctxsize	=	sizeof(struct zynqmp_aes_op),
+	.base.cra_alignmask	=	15,
+	.base.cra_module	=	THIS_MODULE,
+	.min_keysize		=	0,
+	.max_keysize		=	ZYNQMP_AES_KEY_SIZE,
+	.setkey			=	zynqmp_setkey_blk,
+	.encrypt		=	zynqmp_aes_encrypt,
+	.decrypt		=	zynqmp_aes_decrypt,
+	.ivsize			=	ZYNQMP_AES_IV_SIZE,
+};
+
+static const struct of_device_id zynqmp_aes_dt_ids[] = {
+	{ .compatible = "xlnx,zynqmp-aes" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, zynqmp_aes_dt_ids);
+
+static int zynqmp_aes_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	aes_dd = devm_kzalloc(dev, sizeof(*aes_dd), GFP_KERNEL);
+	if (!aes_dd)
+		return -ENOMEM;
+
+	aes_dd->dev = dev;
+	platform_set_drvdata(pdev, aes_dd);
+
+	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+	if (ret < 0) {
+		dev_err(dev, "no usable DMA configuration");
+		return ret;
+	}
+
+	ret = crypto_register_skcipher(&zynqmp_alg);
+	if (ret)
+		goto err_algs;
+
+	dev_info(dev, "AES Successfully Registered\n");
+	return 0;
+
+err_algs:
+	dev_err(dev, "initialization failed.\n");
+
+	return ret;
+}
+
+static int zynqmp_aes_remove(struct platform_device *pdev)
+{
+	aes_dd = platform_get_drvdata(pdev);
+	if (!aes_dd)
+		return -ENODEV;
+	crypto_unregister_skcipher(&zynqmp_alg);
+	return 0;
+}
+
+static struct platform_driver xilinx_aes_driver = {
+	.probe = zynqmp_aes_probe,
+	.remove = zynqmp_aes_remove,
+	.driver = {
+		.name = "zynqmp_aes",
+		.of_match_table = of_match_ptr(zynqmp_aes_dt_ids),
+	},
+};
+
+module_platform_driver(xilinx_aes_driver);
+
+MODULE_DESCRIPTION("Xilinx ZynqMP AES hw acceleration support.");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Nava kishore Manne <nava.manne@xilinx.com>");
+MODULE_AUTHOR("Kalyani Akula <kalyani.akula@xilinx.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/xilinx/zynqmp-rsa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/xilinx/zynqmp-rsa.c
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Xilinx, Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/crypto.h>
+#include <linux/spinlock.h>
+#include <crypto/algapi.h>
+#include <crypto/aes.h>
+#include <crypto/internal/skcipher.h>
+#include <linux/io.h>
+#include <linux/device.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+#include <crypto/scatterwalk.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define ZYNQMP_RSA_QUEUE_LENGTH	1
+#define ZYNQMP_RSA_MAX_KEY_SIZE	1024
+#define ZYNQMP_RSA_BLOCKSIZE	64
+
+/* Key size in bytes */
+#define XSECURE_RSA_512_KEY_SIZE	(512U / 8U)
+#define XSECURE_RSA_576_KEY_SIZE	(576U / 8U)
+#define XSECURE_RSA_704_KEY_SIZE	(704U / 8U)
+#define XSECURE_RSA_768_KEY_SIZE	(768U / 8U)
+#define XSECURE_RSA_992_KEY_SIZE	(992U / 8U)
+#define XSECURE_RSA_1024_KEY_SIZE	(1024U / 8U)
+#define XSECURE_RSA_1152_KEY_SIZE	(1152U / 8U)
+#define XSECURE_RSA_1408_KEY_SIZE	(1408U / 8U)
+#define XSECURE_RSA_1536_KEY_SIZE	(1536U / 8U)
+#define XSECURE_RSA_1984_KEY_SIZE	(1984U / 8U)
+#define XSECURE_RSA_2048_KEY_SIZE	(2048U / 8U)
+#define XSECURE_RSA_3072_KEY_SIZE	(3072U / 8U)
+#define XSECURE_RSA_4096_KEY_SIZE	(4096U / 8U)
+
+static struct zynqmp_rsa_dev *rsa_dd;
+
+struct zynqmp_rsa_op {
+	struct zynqmp_rsa_dev    *dd;
+	void *src;
+	void *dst;
+	int len;
+	u8 key[ZYNQMP_RSA_MAX_KEY_SIZE];
+	u8 *iv;
+	u32 keylen;
+};
+
+struct zynqmp_rsa_dev {
+	struct list_head        list;
+	struct device           *dev;
+	/* the lock protects queue and dev list*/
+	spinlock_t              lock;
+	struct crypto_queue     queue;
+};
+
+struct zynqmp_rsa_drv {
+	struct list_head        dev_list;
+	/* the lock protects queue and dev list*/
+	spinlock_t              lock;
+};
+
+static struct zynqmp_rsa_drv zynqmp_rsa = {
+	.dev_list = LIST_HEAD_INIT(zynqmp_rsa.dev_list),
+	.lock = __SPIN_LOCK_UNLOCKED(zynqmp_rsa.lock),
+};
+
+static struct zynqmp_rsa_dev *zynqmp_rsa_find_dev(struct zynqmp_rsa_op *ctx)
+{
+	struct zynqmp_rsa_dev *dd = rsa_dd;
+
+	spin_lock_bh(&zynqmp_rsa.lock);
+	if (!ctx->dd)
+		ctx->dd = dd;
+	else
+		dd = ctx->dd;
+	spin_unlock_bh(&zynqmp_rsa.lock);
+
+	return dd;
+}
+
+static int zynqmp_setkey_blk(struct crypto_skcipher *tfm, const u8 *key,
+			     unsigned int len)
+{
+	struct zynqmp_rsa_op *op = crypto_skcipher_ctx(tfm);
+
+	op->keylen = len;
+	memcpy(op->key, key, len);
+	return 0;
+}
+
+static int zynqmp_rsa_xcrypt(struct skcipher_request *req, unsigned int flags)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct zynqmp_rsa_op *op = crypto_skcipher_ctx(tfm);
+	struct zynqmp_rsa_dev *dd = zynqmp_rsa_find_dev(op);
+	int err, datasize, src_data = 0, dst_data = 0;
+	struct skcipher_walk walk = {0};
+	unsigned int nbytes;
+	char *kbuf;
+	size_t dma_size;
+	dma_addr_t dma_addr;
+
+	nbytes = req->cryptlen;
+	dma_size = nbytes + op->keylen;
+	kbuf = dma_alloc_coherent(dd->dev, dma_size, &dma_addr, GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	err = skcipher_walk_virt(&walk, req, false);
+	if (err)
+		goto out;
+
+	while ((datasize = walk.nbytes)) {
+		op->src = walk.src.virt.addr;
+		memcpy(kbuf + src_data, op->src, datasize);
+		src_data = src_data + datasize;
+		err = skcipher_walk_done(&walk, 0);
+		if (err)
+			goto out;
+	}
+	memcpy(kbuf + nbytes, op->key, op->keylen);
+
+	if (nbytes != XSECURE_RSA_512_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_576_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_704_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_768_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_992_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_1024_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_1152_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_1408_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_1536_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_1984_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_2048_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_3072_KEY_SIZE ||
+	    nbytes != XSECURE_RSA_4096_KEY_SIZE) {
+		return -EOPNOTSUPP;
+	}
+
+	zynqmp_pm_rsa(dma_addr, nbytes, flags);
+
+	err = skcipher_walk_virt(&walk, req, false);
+	if (err)
+		goto out;
+
+	while ((datasize = walk.nbytes)) {
+		memcpy(walk.dst.virt.addr, kbuf + dst_data, datasize);
+		dst_data = dst_data + datasize;
+		err = skcipher_walk_done(&walk, 0);
+	}
+
+out:
+	dma_free_coherent(dd->dev, dma_size, kbuf, dma_addr);
+	return err;
+}
+
+static int zynqmp_rsa_decrypt(struct skcipher_request *req)
+{
+	return zynqmp_rsa_xcrypt(req, 0);
+}
+
+static int zynqmp_rsa_encrypt(struct skcipher_request *req)
+{
+	return zynqmp_rsa_xcrypt(req, 1);
+}
+
+static struct skcipher_alg zynqmp_alg = {
+	.base.cra_name		=	"xilinx-zynqmp-rsa",
+	.base.cra_driver_name	=	"zynqmp-rsa",
+	.base.cra_priority	=	400,
+	.base.cra_flags		=	CRYPTO_ALG_TYPE_SKCIPHER |
+					CRYPTO_ALG_KERN_DRIVER_ONLY,
+	.base.cra_blocksize	=	ZYNQMP_RSA_BLOCKSIZE,
+	.base.cra_ctxsize	=	sizeof(struct zynqmp_rsa_op),
+	.base.cra_alignmask	=	15,
+	.base.cra_module	=	THIS_MODULE,
+	.min_keysize		=	0,
+	.max_keysize		=	ZYNQMP_RSA_MAX_KEY_SIZE,
+	.setkey			=	zynqmp_setkey_blk,
+	.encrypt		=	zynqmp_rsa_encrypt,
+	.decrypt		=	zynqmp_rsa_decrypt,
+	.ivsize			=	1,
+};
+
+static const struct of_device_id zynqmp_rsa_dt_ids[] = {
+	{ .compatible = "xlnx,zynqmp-rsa" },
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, zynqmp_rsa_dt_ids);
+
+static int zynqmp_rsa_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	rsa_dd = devm_kzalloc(&pdev->dev, sizeof(*rsa_dd), GFP_KERNEL);
+	if (!rsa_dd)
+		return -ENOMEM;
+
+	rsa_dd->dev = dev;
+	platform_set_drvdata(pdev, rsa_dd);
+
+	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret < 0)
+		dev_err(dev, "no usable DMA configuration");
+
+	INIT_LIST_HEAD(&rsa_dd->list);
+	spin_lock_init(&rsa_dd->lock);
+	crypto_init_queue(&rsa_dd->queue, ZYNQMP_RSA_QUEUE_LENGTH);
+	spin_lock(&zynqmp_rsa.lock);
+	list_add_tail(&rsa_dd->list, &zynqmp_rsa.dev_list);
+	spin_unlock(&zynqmp_rsa.lock);
+
+	ret = crypto_register_skcipher(&zynqmp_alg);
+	if (ret)
+		goto err_algs;
+
+	return 0;
+
+err_algs:
+	spin_lock(&zynqmp_rsa.lock);
+	list_del(&rsa_dd->list);
+	spin_unlock(&zynqmp_rsa.lock);
+	dev_err(dev, "initialization failed.\n");
+	return ret;
+}
+
+static int zynqmp_rsa_remove(struct platform_device *pdev)
+{
+	crypto_unregister_skcipher(&zynqmp_alg);
+	return 0;
+}
+
+static struct platform_driver xilinx_rsa_driver = {
+	.probe = zynqmp_rsa_probe,
+	.remove = zynqmp_rsa_remove,
+	.driver = {
+		.name = "zynqmp_rsa",
+		.of_match_table = of_match_ptr(zynqmp_rsa_dt_ids),
+	},
+};
+
+module_platform_driver(xilinx_rsa_driver);
+
+MODULE_DESCRIPTION("ZynqMP RSA hw acceleration support.");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Nava kishore Manne <navam@xilinx.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/xilinx/zynqmp-sha-deprecated.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/xilinx/zynqmp-sha-deprecated.c
@@ -0,0 +1,295 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Xilinx, Inc.
+ */
+
+#include <asm/cacheflush.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/scatterlist.h>
+#include <linux/dma-mapping.h>
+#include <linux/of_device.h>
+#include <linux/crypto.h>
+#include <crypto/scatterwalk.h>
+#include <crypto/algapi.h>
+#include <crypto/sha1.h>
+#include <crypto/sha2.h>
+#include <crypto/hash.h>
+#include <crypto/internal/hash.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/mutex.h>
+
+#define ZYNQMP_SHA3_INIT	1
+#define ZYNQMP_SHA3_UPDATE	2
+#define ZYNQMP_SHA3_FINAL	4
+
+#define ZYNQMP_SHA_QUEUE_LENGTH	1
+
+static struct zynqmp_sha_dev *sha_dd;
+
+/*
+ * .statesize = sizeof(struct zynqmp_sha_reqctx) must be <= PAGE_SIZE / 8 as
+ * tested by the ahash_prepare_alg() function.
+ */
+struct zynqmp_sha_reqctx {
+	struct zynqmp_sha_dev	*dd;
+	unsigned long		flags;
+};
+
+struct zynqmp_sha_ctx {
+	struct zynqmp_sha_dev	*dd;
+	unsigned long		flags;
+};
+
+struct zynqmp_sha_dev {
+	struct list_head	list;
+	struct device		*dev;
+	/* the lock protects queue and dev list*/
+	spinlock_t		lock;
+	int			err;
+
+	unsigned long		flags;
+	struct crypto_queue	queue;
+	struct ahash_request	*req;
+};
+
+struct zynqmp_sha_drv {
+	struct list_head	dev_list;
+	/* the lock protects queue and dev list*/
+	spinlock_t		lock;
+	/* the hw_engine_mutex makes the driver thread-safe */
+	struct mutex		hw_engine_mutex;
+};
+
+static struct zynqmp_sha_drv zynqmp_sha = {
+	.dev_list = LIST_HEAD_INIT(zynqmp_sha.dev_list),
+	.lock = __SPIN_LOCK_UNLOCKED(zynqmp_sha.lock),
+};
+
+static int zynqmp_sha_init(struct ahash_request *req)
+{
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
+	struct zynqmp_sha_ctx *tctx = crypto_ahash_ctx(tfm);
+	struct zynqmp_sha_reqctx *ctx = ahash_request_ctx(req);
+	struct zynqmp_sha_dev *dd = sha_dd;
+	int ret;
+
+	spin_lock_bh(&zynqmp_sha.lock);
+	if (!tctx->dd)
+		tctx->dd = dd;
+	else
+		dd = tctx->dd;
+
+	spin_unlock_bh(&zynqmp_sha.lock);
+
+	ctx->dd = dd;
+	dev_dbg(dd->dev, "init: digest size: %d\n",
+		crypto_ahash_digestsize(tfm));
+
+	ret = mutex_lock_interruptible(&zynqmp_sha.hw_engine_mutex);
+	if (ret)
+		goto end;
+
+	ret = zynqmp_pm_sha_hash(0, 0, ZYNQMP_SHA3_INIT);
+
+end:
+	return ret;
+}
+
+static int zynqmp_sha_update(struct ahash_request *req)
+{
+	struct zynqmp_sha_ctx *tctx = crypto_tfm_ctx(req->base.tfm);
+	struct zynqmp_sha_dev *dd = tctx->dd;
+	char *kbuf;
+	size_t dma_size = req->nbytes;
+	dma_addr_t dma_addr;
+	int ret;
+
+	if (!req->nbytes)
+		return 0;
+
+	kbuf = dma_alloc_coherent(dd->dev, dma_size, &dma_addr, GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	scatterwalk_map_and_copy(kbuf, req->src, 0, req->nbytes, 0);
+	caches_clean_inval_user_pou((unsigned long)kbuf,
+				    (unsigned long)kbuf + dma_size);
+	ret = zynqmp_pm_sha_hash(dma_addr, req->nbytes, ZYNQMP_SHA3_UPDATE);
+	if (ret) {
+		mutex_unlock(&zynqmp_sha.hw_engine_mutex);
+		goto end;
+	}
+
+	dma_free_coherent(dd->dev, dma_size, kbuf, dma_addr);
+
+end:
+	return ret;
+}
+
+static int zynqmp_sha_final(struct ahash_request *req)
+{
+	struct zynqmp_sha_ctx *tctx = crypto_tfm_ctx(req->base.tfm);
+	struct zynqmp_sha_dev *dd = tctx->dd;
+	char *kbuf;
+	size_t dma_size = SHA384_DIGEST_SIZE;
+	dma_addr_t dma_addr;
+	int ret;
+
+	kbuf = dma_alloc_coherent(dd->dev, dma_size, &dma_addr, GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	ret = zynqmp_pm_sha_hash(dma_addr, dma_size, ZYNQMP_SHA3_FINAL);
+	memcpy(req->result, kbuf, 48);
+	dma_free_coherent(dd->dev, dma_size, kbuf, dma_addr);
+
+	mutex_unlock(&zynqmp_sha.hw_engine_mutex);
+	return ret;
+}
+
+static int zynqmp_sha_finup(struct ahash_request *req)
+{
+	zynqmp_sha_update(req);
+	zynqmp_sha_final(req);
+
+	return 0;
+}
+
+static int zynqmp_sha_digest(struct ahash_request *req)
+{
+	zynqmp_sha_init(req);
+	zynqmp_sha_update(req);
+	zynqmp_sha_final(req);
+
+	return 0;
+}
+
+static int zynqmp_sha_export(struct ahash_request *req, void *out)
+{
+	const struct zynqmp_sha_reqctx *ctx = ahash_request_ctx(req);
+
+	memcpy(out, ctx, sizeof(*ctx));
+	return 0;
+}
+
+static int zynqmp_sha_import(struct ahash_request *req, const void *in)
+{
+	struct zynqmp_sha_reqctx *ctx = ahash_request_ctx(req);
+
+	memcpy(ctx, in, sizeof(*ctx));
+	return 0;
+}
+
+static int zynqmp_sha_cra_init(struct crypto_tfm *tfm)
+{
+	crypto_ahash_set_reqsize(__crypto_ahash_cast(tfm),
+				 sizeof(struct zynqmp_sha_reqctx));
+
+	return 0;
+}
+
+static struct ahash_alg sha3_alg = {
+	.init		= zynqmp_sha_init,
+	.update		= zynqmp_sha_update,
+	.final		= zynqmp_sha_final,
+	.finup		= zynqmp_sha_finup,
+	.digest		= zynqmp_sha_digest,
+	.export		= zynqmp_sha_export,
+	.import		= zynqmp_sha_import,
+	.halg = {
+		.digestsize	= SHA384_DIGEST_SIZE,
+		.statesize	= sizeof(struct sha256_state),
+		.base	= {
+			.cra_name		= "xilinx-keccak-384",
+			.cra_driver_name	= "zynqmp-keccak-384",
+			.cra_priority		= 300,
+			.cra_flags		= CRYPTO_ALG_ASYNC,
+			.cra_blocksize		= SHA384_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct zynqmp_sha_ctx),
+			.cra_alignmask		= 0,
+			.cra_module		= THIS_MODULE,
+			.cra_init		= zynqmp_sha_cra_init,
+		}
+	}
+};
+
+static const struct of_device_id zynqmp_sha_dt_ids[] = {
+	{ .compatible = "xlnx,zynqmp-keccak-384" },
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, zynqmp_sha_dt_ids);
+
+static int zynqmp_sha_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int err;
+
+	sha_dd = devm_kzalloc(&pdev->dev, sizeof(*sha_dd), GFP_KERNEL);
+	if (!sha_dd)
+		return -ENOMEM;
+
+	sha_dd->dev = dev;
+	platform_set_drvdata(pdev, sha_dd);
+	INIT_LIST_HEAD(&sha_dd->list);
+	spin_lock_init(&sha_dd->lock);
+	mutex_init(&zynqmp_sha.hw_engine_mutex);
+	crypto_init_queue(&sha_dd->queue, ZYNQMP_SHA_QUEUE_LENGTH);
+	spin_lock(&zynqmp_sha.lock);
+	list_add_tail(&sha_dd->list, &zynqmp_sha.dev_list);
+	spin_unlock(&zynqmp_sha.lock);
+
+	err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+	if (err < 0)
+		dev_err(dev, "no usable DMA configuration");
+
+	err = crypto_register_ahash(&sha3_alg);
+	if (err)
+		goto err_algs;
+
+	return 0;
+
+err_algs:
+	spin_lock(&zynqmp_sha.lock);
+	list_del(&sha_dd->list);
+	spin_unlock(&zynqmp_sha.lock);
+	dev_err(dev, "initialization failed.\n");
+
+	return err;
+}
+
+static int zynqmp_sha_remove(struct platform_device *pdev)
+{
+	sha_dd = platform_get_drvdata(pdev);
+
+	if (!sha_dd)
+		return -ENODEV;
+
+	spin_lock(&zynqmp_sha.lock);
+	list_del(&sha_dd->list);
+	spin_unlock(&zynqmp_sha.lock);
+
+	crypto_unregister_ahash(&sha3_alg);
+
+	return 0;
+}
+
+static struct platform_driver zynqmp_sha_driver = {
+	.probe		= zynqmp_sha_probe,
+	.remove		= zynqmp_sha_remove,
+	.driver		= {
+		.name	= "zynqmp-keccak-384",
+		.of_match_table	= of_match_ptr(zynqmp_sha_dt_ids),
+	},
+};
+
+module_platform_driver(zynqmp_sha_driver);
+
+MODULE_DESCRIPTION("ZynqMP SHA3 hw acceleration support.");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Nava kishore Manne <navam@xilinx.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/crypto/xilinx/zynqmp-sha.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/crypto/xilinx/zynqmp-sha.c
@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx ZynqMP SHA Driver.
+ * Copyright (c) 2022 Xilinx Inc.
+ */
+#include <asm/cacheflush.h>
+#include <crypto/hash.h>
+#include <crypto/internal/hash.h>
+#include <crypto/sha3.h>
+#include <linux/crypto.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#define ZYNQMP_DMA_BIT_MASK		32U
+#define ZYNQMP_DMA_ALLOC_FIXED_SIZE	0x1000U
+
+enum zynqmp_sha_op {
+	ZYNQMP_SHA3_INIT = 1,
+	ZYNQMP_SHA3_UPDATE = 2,
+	ZYNQMP_SHA3_FINAL = 4,
+};
+
+struct zynqmp_sha_drv_ctx {
+	struct shash_alg sha3_384;
+	struct device *dev;
+};
+
+struct zynqmp_sha_tfm_ctx {
+	struct device *dev;
+	struct crypto_shash *fbk_tfm;
+};
+
+struct zynqmp_sha_desc_ctx {
+	struct shash_desc fbk_req;
+};
+
+static dma_addr_t update_dma_addr, final_dma_addr;
+static char *ubuf, *fbuf;
+
+static int zynqmp_sha_init_tfm(struct crypto_shash *hash)
+{
+	const char *fallback_driver_name = crypto_shash_alg_name(hash);
+	struct zynqmp_sha_tfm_ctx *tfm_ctx = crypto_shash_ctx(hash);
+	struct shash_alg *alg = crypto_shash_alg(hash);
+	struct crypto_shash *fallback_tfm;
+	struct zynqmp_sha_drv_ctx *drv_ctx;
+
+	drv_ctx = container_of(alg, struct zynqmp_sha_drv_ctx, sha3_384);
+	tfm_ctx->dev = drv_ctx->dev;
+
+	/* Allocate a fallback and abort if it failed. */
+	fallback_tfm = crypto_alloc_shash(fallback_driver_name, 0,
+					  CRYPTO_ALG_NEED_FALLBACK);
+	if (IS_ERR(fallback_tfm))
+		return PTR_ERR(fallback_tfm);
+
+	tfm_ctx->fbk_tfm = fallback_tfm;
+	hash->descsize += crypto_shash_descsize(tfm_ctx->fbk_tfm);
+
+	return 0;
+}
+
+static void zynqmp_sha_exit_tfm(struct crypto_shash *hash)
+{
+	struct zynqmp_sha_tfm_ctx *tfm_ctx = crypto_shash_ctx(hash);
+
+	if (tfm_ctx->fbk_tfm) {
+		crypto_free_shash(tfm_ctx->fbk_tfm);
+		tfm_ctx->fbk_tfm = NULL;
+	}
+
+	memzero_explicit(tfm_ctx, sizeof(struct zynqmp_sha_tfm_ctx));
+}
+
+static int zynqmp_sha_init(struct shash_desc *desc)
+{
+	struct zynqmp_sha_desc_ctx *dctx = shash_desc_ctx(desc);
+	struct zynqmp_sha_tfm_ctx *tctx = crypto_shash_ctx(desc->tfm);
+
+	dctx->fbk_req.tfm = tctx->fbk_tfm;
+	return crypto_shash_init(&dctx->fbk_req);
+}
+
+static int zynqmp_sha_update(struct shash_desc *desc, const u8 *data, unsigned int length)
+{
+	struct zynqmp_sha_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	return crypto_shash_update(&dctx->fbk_req, data, length);
+}
+
+static int zynqmp_sha_final(struct shash_desc *desc, u8 *out)
+{
+	struct zynqmp_sha_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	return crypto_shash_final(&dctx->fbk_req, out);
+}
+
+static int zynqmp_sha_finup(struct shash_desc *desc, const u8 *data, unsigned int length, u8 *out)
+{
+	struct zynqmp_sha_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	return crypto_shash_finup(&dctx->fbk_req, data, length, out);
+}
+
+static int zynqmp_sha_import(struct shash_desc *desc, const void *in)
+{
+	struct zynqmp_sha_desc_ctx *dctx = shash_desc_ctx(desc);
+	struct zynqmp_sha_tfm_ctx *tctx = crypto_shash_ctx(desc->tfm);
+
+	dctx->fbk_req.tfm = tctx->fbk_tfm;
+	return crypto_shash_import(&dctx->fbk_req, in);
+}
+
+static int zynqmp_sha_export(struct shash_desc *desc, void *out)
+{
+	struct zynqmp_sha_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	return crypto_shash_export(&dctx->fbk_req, out);
+}
+
+static int zynqmp_sha_digest(struct shash_desc *desc, const u8 *data, unsigned int len, u8 *out)
+{
+	unsigned int remaining_len = len;
+	int update_size;
+	int ret;
+
+	ret = zynqmp_pm_sha_hash(0, 0, ZYNQMP_SHA3_INIT);
+	if (ret)
+		return ret;
+
+	while (remaining_len != 0) {
+		memzero_explicit(ubuf, ZYNQMP_DMA_ALLOC_FIXED_SIZE);
+		if (remaining_len >= ZYNQMP_DMA_ALLOC_FIXED_SIZE) {
+			update_size = ZYNQMP_DMA_ALLOC_FIXED_SIZE;
+			remaining_len -= ZYNQMP_DMA_ALLOC_FIXED_SIZE;
+		} else {
+			update_size = remaining_len;
+			remaining_len = 0;
+		}
+		memcpy(ubuf, data, update_size);
+		flush_icache_range((unsigned long)ubuf, (unsigned long)ubuf + update_size);
+		ret = zynqmp_pm_sha_hash(update_dma_addr, update_size, ZYNQMP_SHA3_UPDATE);
+		if (ret)
+			return ret;
+
+		data += update_size;
+	}
+
+	ret = zynqmp_pm_sha_hash(final_dma_addr, SHA3_384_DIGEST_SIZE, ZYNQMP_SHA3_FINAL);
+	memcpy(out, fbuf, SHA3_384_DIGEST_SIZE);
+	memzero_explicit(fbuf, SHA3_384_DIGEST_SIZE);
+
+	return ret;
+}
+
+static struct zynqmp_sha_drv_ctx sha3_drv_ctx = {
+	.sha3_384 = {
+		.init = zynqmp_sha_init,
+		.update = zynqmp_sha_update,
+		.final = zynqmp_sha_final,
+		.finup = zynqmp_sha_finup,
+		.digest = zynqmp_sha_digest,
+		.export = zynqmp_sha_export,
+		.import = zynqmp_sha_import,
+		.init_tfm = zynqmp_sha_init_tfm,
+		.exit_tfm = zynqmp_sha_exit_tfm,
+		.descsize = sizeof(struct zynqmp_sha_desc_ctx),
+		.statesize = sizeof(struct sha3_state),
+		.digestsize = SHA3_384_DIGEST_SIZE,
+		.base = {
+			.cra_name = "sha3-384",
+			.cra_driver_name = "zynqmp-sha3-384",
+			.cra_priority = 300,
+			.cra_flags = CRYPTO_ALG_KERN_DRIVER_ONLY |
+				     CRYPTO_ALG_ALLOCATES_MEMORY |
+				     CRYPTO_ALG_NEED_FALLBACK,
+			.cra_blocksize = SHA3_384_BLOCK_SIZE,
+			.cra_ctxsize = sizeof(struct zynqmp_sha_tfm_ctx),
+			.cra_alignmask = 3,
+			.cra_module = THIS_MODULE,
+		}
+	}
+};
+
+static int zynqmp_sha_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int err;
+	u32 v;
+
+	/* Verify the hardware is present */
+	err = zynqmp_pm_get_api_version(&v);
+	if (err)
+		return err;
+
+
+	err = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(ZYNQMP_DMA_BIT_MASK));
+	if (err < 0) {
+		dev_err(dev, "No usable DMA configuration\n");
+		return err;
+	}
+
+	err = crypto_register_shash(&sha3_drv_ctx.sha3_384);
+	if (err < 0) {
+		dev_err(dev, "Failed to register shash alg.\n");
+		return err;
+	}
+
+	sha3_drv_ctx.dev = dev;
+	platform_set_drvdata(pdev, &sha3_drv_ctx);
+
+	ubuf = dma_alloc_coherent(dev, ZYNQMP_DMA_ALLOC_FIXED_SIZE, &update_dma_addr, GFP_KERNEL);
+	if (!ubuf) {
+		err = -ENOMEM;
+		goto err_shash;
+	}
+
+	fbuf = dma_alloc_coherent(dev, SHA3_384_DIGEST_SIZE, &final_dma_addr, GFP_KERNEL);
+	if (!fbuf) {
+		err = -ENOMEM;
+		goto err_mem;
+	}
+
+	return 0;
+
+err_mem:
+	dma_free_coherent(sha3_drv_ctx.dev, ZYNQMP_DMA_ALLOC_FIXED_SIZE, ubuf, update_dma_addr);
+
+err_shash:
+	crypto_unregister_shash(&sha3_drv_ctx.sha3_384);
+
+	return err;
+}
+
+static int zynqmp_sha_remove(struct platform_device *pdev)
+{
+	sha3_drv_ctx.dev = platform_get_drvdata(pdev);
+
+	dma_free_coherent(sha3_drv_ctx.dev, ZYNQMP_DMA_ALLOC_FIXED_SIZE, ubuf, update_dma_addr);
+	dma_free_coherent(sha3_drv_ctx.dev, SHA3_384_DIGEST_SIZE, fbuf, final_dma_addr);
+	crypto_unregister_shash(&sha3_drv_ctx.sha3_384);
+
+	return 0;
+}
+
+static struct platform_driver zynqmp_sha_driver = {
+	.probe = zynqmp_sha_probe,
+	.remove = zynqmp_sha_remove,
+	.driver = {
+		.name = "zynqmp-sha3-384",
+	},
+};
+
+module_platform_driver(zynqmp_sha_driver);
+MODULE_DESCRIPTION("ZynqMP SHA3 hardware acceleration support.");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Harsha <harsha.harsha@xilinx.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cxl/core/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cxl/core/bus.c
@@ -182,6 +182,7 @@
 
 	ida_free(&port->decoder_ida, cxld->id);
 	kfree(cxld);
+	put_device(&port->dev);
 }
 
 static const struct device_type cxl_decoder_switch_type = {
@@ -481,6 +482,9 @@
 	if (rc < 0)
 		goto err;
 
+	/* need parent to stick around to release the id */
+	get_device(&port->dev);
+
 	*cxld = (struct cxl_decoder) {
 		.id = rc,
 		.range = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cxl/core/memdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cxl/core/memdev.c
@@ -139,10 +139,9 @@
 	struct cdev *cdev = &cxlmd->cdev;
 	const struct cdevm_file_operations *cdevm_fops;
 
+	cdev_device_del(&cxlmd->cdev, dev);
 	cdevm_fops = container_of(cdev->ops, typeof(*cdevm_fops), fops);
 	cdevm_fops->shutdown(dev);
-
-	cdev_device_del(&cxlmd->cdev, dev);
 	put_device(dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cxl/core/regs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cxl/core/regs.c
@@ -35,7 +35,7 @@
 			      struct cxl_component_reg_map *map)
 {
 	int cap, cap_count;
-	u64 cap_array;
+	u32 cap_array;
 
 	*map = (struct cxl_component_reg_map) { 0 };
 
@@ -45,11 +45,11 @@
 	 */
 	base += CXL_CM_OFFSET;
 
-	cap_array = readq(base + CXL_CM_CAP_HDR_OFFSET);
+	cap_array = readl(base + CXL_CM_CAP_HDR_OFFSET);
 
 	if (FIELD_GET(CXL_CM_CAP_HDR_ID_MASK, cap_array) != CM_CAP_HDR_CAP_ID) {
 		dev_err(dev,
-			"Couldn't locate the CXL.cache and CXL.mem capability array header./n");
+			"Couldn't locate the CXL.cache and CXL.mem capability array header.\n");
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cxl/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cxl/pci.c
@@ -972,7 +972,7 @@
 	if (pci_resource_len(pdev, bar) < offset) {
 		dev_err(dev, "BAR%d: %pr: too small (offset: %#llx)\n", bar,
 			&pdev->resource[bar], (unsigned long long)offset);
-		return IOMEM_ERR_PTR(-ENXIO);
+		return NULL;
 	}
 
 	addr = pci_iomap(pdev, bar, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/cxl/pmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/cxl/pmem.c
@@ -149,14 +149,24 @@
 	put_device(&cxl_nvb->dev);
 }
 
+static void cxl_nvdimm_bridge_state_work(struct cxl_nvdimm_bridge *cxl_nvb)
+{
+	/*
+	 * Take a reference that the workqueue will drop if new work
+	 * gets queued.
+	 */
+	get_device(&cxl_nvb->dev);
+	if (!queue_work(cxl_pmem_wq, &cxl_nvb->state_work))
+		put_device(&cxl_nvb->dev);
+}
+
 static void cxl_nvdimm_bridge_remove(struct device *dev)
 {
 	struct cxl_nvdimm_bridge *cxl_nvb = to_cxl_nvdimm_bridge(dev);
 
 	if (cxl_nvb->state == CXL_NVB_ONLINE)
 		cxl_nvb->state = CXL_NVB_OFFLINE;
-	if (queue_work(cxl_pmem_wq, &cxl_nvb->state_work))
-		get_device(&cxl_nvb->dev);
+	cxl_nvdimm_bridge_state_work(cxl_nvb);
 }
 
 static int cxl_nvdimm_bridge_probe(struct device *dev)
@@ -177,8 +187,7 @@
 	}
 
 	cxl_nvb->state = CXL_NVB_ONLINE;
-	if (queue_work(cxl_pmem_wq, &cxl_nvb->state_work))
-		get_device(&cxl_nvb->dev);
+	cxl_nvdimm_bridge_state_work(cxl_nvb);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dax/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dax/bus.c
@@ -397,23 +397,39 @@
 	dev_dbg(dev, "%s\n", __func__);
 
 	kill_dev_dax(dev_dax);
-	free_dev_dax_ranges(dev_dax);
 	device_del(dev);
+	free_dev_dax_ranges(dev_dax);
 	put_device(dev);
 }
 
+static void dax_region_free(struct kref *kref)
+{
+	struct dax_region *dax_region;
+
+	dax_region = container_of(kref, struct dax_region, kref);
+	kfree(dax_region);
+}
+
+void dax_region_put(struct dax_region *dax_region)
+{
+	kref_put(&dax_region->kref, dax_region_free);
+}
+EXPORT_SYMBOL_GPL(dax_region_put);
+
 /* a return value >= 0 indicates this invocation invalidated the id */
 static int __free_dev_dax_id(struct dev_dax *dev_dax)
 {
-	struct dax_region *dax_region = dev_dax->region;
 	struct device *dev = &dev_dax->dev;
+	struct dax_region *dax_region;
 	int rc = dev_dax->id;
 
 	device_lock_assert(dev);
 
-	if (is_static(dax_region) || dev_dax->id < 0)
+	if (!dev_dax->dyn_id || dev_dax->id < 0)
 		return -1;
+	dax_region = dev_dax->region;
 	ida_free(&dax_region->ida, dev_dax->id);
+	dax_region_put(dax_region);
 	dev_dax->id = -1;
 	return rc;
 }
@@ -429,6 +445,20 @@
 	return rc;
 }
 
+static int alloc_dev_dax_id(struct dev_dax *dev_dax)
+{
+	struct dax_region *dax_region = dev_dax->region;
+	int id;
+
+	id = ida_alloc(&dax_region->ida, GFP_KERNEL);
+	if (id < 0)
+		return id;
+	kref_get(&dax_region->kref);
+	dev_dax->dyn_id = true;
+	dev_dax->id = id;
+	return id;
+}
+
 static ssize_t delete_store(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t len)
 {
@@ -516,20 +546,6 @@
 	NULL,
 };
 
-static void dax_region_free(struct kref *kref)
-{
-	struct dax_region *dax_region;
-
-	dax_region = container_of(kref, struct dax_region, kref);
-	kfree(dax_region);
-}
-
-void dax_region_put(struct dax_region *dax_region)
-{
-	kref_put(&dax_region->kref, dax_region_free);
-}
-EXPORT_SYMBOL_GPL(dax_region_put);
-
 static void dax_region_unregister(void *region)
 {
 	struct dax_region *dax_region = region;
@@ -591,10 +607,12 @@
 static void dax_mapping_release(struct device *dev)
 {
 	struct dax_mapping *mapping = to_dax_mapping(dev);
-	struct dev_dax *dev_dax = to_dev_dax(dev->parent);
+	struct device *parent = dev->parent;
+	struct dev_dax *dev_dax = to_dev_dax(parent);
 
 	ida_free(&dev_dax->ida, mapping->id);
 	kfree(mapping);
+	put_device(parent);
 }
 
 static void unregister_dax_mapping(void *data)
@@ -734,6 +752,7 @@
 	dev = &mapping->dev;
 	device_initialize(dev);
 	dev->parent = &dev_dax->dev;
+	get_device(dev->parent);
 	dev->type = &dax_mapping_type;
 	dev_set_name(dev, "mapping%d", mapping->id);
 	rc = device_add(dev);
@@ -1251,12 +1270,10 @@
 static void dev_dax_release(struct device *dev)
 {
 	struct dev_dax *dev_dax = to_dev_dax(dev);
-	struct dax_region *dax_region = dev_dax->region;
 	struct dax_device *dax_dev = dev_dax->dax_dev;
 
 	put_dax(dax_dev);
 	free_dev_dax_id(dev_dax);
-	dax_region_put(dax_region);
 	kfree(dev_dax->pgmap);
 	kfree(dev_dax);
 }
@@ -1280,6 +1297,7 @@
 	if (!dev_dax)
 		return ERR_PTR(-ENOMEM);
 
+	dev_dax->region = dax_region;
 	if (is_static(dax_region)) {
 		if (dev_WARN_ONCE(parent, data->id < 0,
 				"dynamic id specified to static region\n")) {
@@ -1295,13 +1313,11 @@
 			goto err_id;
 		}
 
-		rc = ida_alloc(&dax_region->ida, GFP_KERNEL);
+		rc = alloc_dev_dax_id(dev_dax);
 		if (rc < 0)
 			goto err_id;
-		dev_dax->id = rc;
 	}
 
-	dev_dax->region = dax_region;
 	dev = &dev_dax->dev;
 	device_initialize(dev);
 	dev_set_name(dev, "dax%d.%d", dax_region->id, dev_dax->id);
@@ -1339,7 +1355,6 @@
 	dev_dax->target_node = dax_region->target_node;
 	dev_dax->align = dax_region->align;
 	ida_init(&dev_dax->ida);
-	kref_get(&dax_region->kref);
 
 	inode = dax_inode(dax_dev);
 	dev->devt = inode->i_rdev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dax/dax-private.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dax/dax-private.h
@@ -52,7 +52,8 @@
  * @region - parent region
  * @dax_dev - core dax functionality
  * @target_node: effective numa node if dev_dax memory range is onlined
- * @id: ida allocated id
+ * @dyn_id: is this a dynamic or statically created instance
+ * @id: ida allocated id when the dax_region is not static
  * @ida: mapping id allocator
  * @dev - device core
  * @pgmap - pgmap for memmap setup / lifetime (driver owned)
@@ -64,6 +65,7 @@
 	struct dax_device *dax_dev;
 	unsigned int align;
 	int target_node;
+	bool dyn_id;
 	int id;
 	struct ida ida;
 	struct device dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dax/hmem/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dax/hmem/device.c
@@ -8,6 +8,13 @@
 static bool nohmem;
 module_param_named(disable, nohmem, bool, 0444);
 
+static struct resource hmem_active = {
+	.name = "HMEM devices",
+	.start = 0,
+	.end = -1,
+	.flags = IORESOURCE_MEM,
+};
+
 void hmem_register_device(int target_nid, struct resource *r)
 {
 	/* define a clean / non-busy resource for the platform device */
@@ -15,6 +22,7 @@
 		.start = r->start,
 		.end = r->end,
 		.flags = IORESOURCE_MEM,
+		.desc = IORES_DESC_SOFT_RESERVED,
 	};
 	struct platform_device *pdev;
 	struct memregion_info info;
@@ -40,6 +48,12 @@
 		goto out_pdev;
 	}
 
+	if (!__request_region(&hmem_active, res.start, resource_size(&res),
+			      dev_name(&pdev->dev), 0)) {
+		dev_dbg(&pdev->dev, "hmem range %pr already active\n", &res);
+		goto out_active;
+	}
+
 	pdev->dev.numa_node = numa_map_to_online_node(target_nid);
 	info = (struct memregion_info) {
 		.target_node = target_nid,
@@ -65,22 +79,15 @@
 	return;
 
 out_resource:
-	put_device(&pdev->dev);
+	__release_region(&hmem_active, res.start, resource_size(&res));
+out_active:
+	platform_device_put(pdev);
 out_pdev:
 	memregion_free(id);
 }
 
 static __init int hmem_register_one(struct resource *res, void *data)
 {
-	/*
-	 * If the resource is not a top-level resource it was already
-	 * assigned to a device by the HMAT parsing.
-	 */
-	if (res->parent != &iomem_resource) {
-		pr_info("HMEM: skip %pr, already claimed\n", res);
-		return 0;
-	}
-
 	hmem_register_device(phys_to_target_node(res->start), res);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dax/kmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dax/kmem.c
@@ -88,7 +88,7 @@
 	if (!data->res_name)
 		goto err_res_name;
 
-	rc = memory_group_register_static(numa_node, total_len);
+	rc = memory_group_register_static(numa_node, PFN_UP(total_len));
 	if (rc < 0)
 		goto err_reg_mgid;
 	data->mgid = rc;
@@ -135,7 +135,7 @@
 		if (rc) {
 			dev_warn(dev, "mapping%d: %#llx-%#llx memory add failed\n",
 					i, range.start, range.end);
-			release_resource(res);
+			remove_resource(res);
 			kfree(res);
 			data->res[i] = NULL;
 			if (mapped)
@@ -181,7 +181,7 @@
 
 		rc = remove_memory(range.start, range_len(&range));
 		if (rc == 0) {
-			release_resource(data->res[i]);
+			remove_resource(data->res[i]);
 			kfree(data->res[i]);
 			data->res[i] = NULL;
 			success++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dax/super.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dax/super.c
@@ -678,6 +678,7 @@
 static void dax_fs_exit(void)
 {
 	kern_unmount(dax_mnt);
+	rcu_barrier();
 	kmem_cache_destroy(dax_cache);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/devfreq/devfreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/devfreq/devfreq.c
@@ -464,10 +464,14 @@
 	if (err)
 		dev_err(&devfreq->dev, "dvfs failed with (%d) error\n", err);
 
+	if (devfreq->stop_polling)
+		goto out;
+
 	queue_delayed_work(devfreq_wq, &devfreq->work,
 				msecs_to_jiffies(devfreq->profile->polling_ms));
-	mutex_unlock(&devfreq->lock);
 
+out:
+	mutex_unlock(&devfreq->lock);
 	trace_devfreq_monitor(devfreq);
 }
 
@@ -485,6 +489,10 @@
 	if (IS_SUPPORTED_FLAG(devfreq->governor->flags, IRQ_DRIVEN))
 		return;
 
+	mutex_lock(&devfreq->lock);
+	if (delayed_work_pending(&devfreq->work))
+		goto out;
+
 	switch (devfreq->profile->timer) {
 	case DEVFREQ_TIMER_DEFERRABLE:
 		INIT_DEFERRABLE_WORK(&devfreq->work, devfreq_monitor);
@@ -493,12 +501,16 @@
 		INIT_DELAYED_WORK(&devfreq->work, devfreq_monitor);
 		break;
 	default:
-		return;
+		goto out;
 	}
 
 	if (devfreq->profile->polling_ms)
 		queue_delayed_work(devfreq_wq, &devfreq->work,
 			msecs_to_jiffies(devfreq->profile->polling_ms));
+
+out:
+	devfreq->stop_polling = false;
+	mutex_unlock(&devfreq->lock);
 }
 EXPORT_SYMBOL(devfreq_monitor_start);
 
@@ -515,6 +527,14 @@
 	if (IS_SUPPORTED_FLAG(devfreq->governor->flags, IRQ_DRIVEN))
 		return;
 
+	mutex_lock(&devfreq->lock);
+	if (devfreq->stop_polling) {
+		mutex_unlock(&devfreq->lock);
+		return;
+	}
+
+	devfreq->stop_polling = true;
+	mutex_unlock(&devfreq->lock);
 	cancel_delayed_work_sync(&devfreq->work);
 }
 EXPORT_SYMBOL(devfreq_monitor_stop);
@@ -762,6 +782,7 @@
 		dev_pm_opp_put_opp_table(devfreq->opp_table);
 
 	mutex_destroy(&devfreq->lock);
+	srcu_cleanup_notifier_head(&devfreq->transition_notifier_list);
 	kfree(devfreq);
 }
 
@@ -775,8 +796,7 @@
  * @dev:	the device to add devfreq feature.
  * @profile:	device-specific profile to run devfreq.
  * @governor_name:	name of the policy to choose frequency.
- * @data:	private data for the governor. The devfreq framework does not
- *		touch this value.
+ * @data:	devfreq driver pass to governors, governor should not change it.
  */
 struct devfreq *devfreq_add_device(struct device *dev,
 				   struct devfreq_dev_profile *profile,
@@ -1003,8 +1023,7 @@
  * @dev:	the device to add devfreq feature.
  * @profile:	device-specific profile to run devfreq.
  * @governor_name:	name of the policy to choose frequency.
- * @data:	private data for the governor. The devfreq framework does not
- *		touch this value.
+ * @data:	 devfreq driver pass to governors, governor should not change it.
  *
  * This function manages automatically the memory of devfreq device using device
  * resource management and simplify the free operation for memory of devfreq
@@ -1654,7 +1673,7 @@
 			       struct device_attribute *attr, char *buf)
 {
 	struct devfreq *df = to_devfreq(dev);
-	ssize_t len;
+	ssize_t len = 0;
 	int i, j;
 	unsigned int max_state;
 
@@ -1663,7 +1682,7 @@
 	max_state = df->profile->max_state;
 
 	if (max_state == 0)
-		return sprintf(buf, "Not Supported.\n");
+		return scnprintf(buf, PAGE_SIZE, "Not Supported.\n");
 
 	mutex_lock(&df->lock);
 	if (!df->stop_polling &&
@@ -1673,33 +1692,54 @@
 	}
 	mutex_unlock(&df->lock);
 
-	len = sprintf(buf, "     From  :   To\n");
-	len += sprintf(buf + len, "           :");
-	for (i = 0; i < max_state; i++)
-		len += sprintf(buf + len, "%10lu",
-				df->profile->freq_table[i]);
+	len += scnprintf(buf + len, PAGE_SIZE - len, "     From  :   To\n");
+	len += scnprintf(buf + len, PAGE_SIZE - len, "           :");
+	for (i = 0; i < max_state; i++) {
+		if (len >= PAGE_SIZE - 1)
+			break;
+		len += scnprintf(buf + len, PAGE_SIZE - len, "%10lu",
+				 df->profile->freq_table[i]);
+	}
+	if (len >= PAGE_SIZE - 1)
+		return PAGE_SIZE - 1;
 
-	len += sprintf(buf + len, "   time(ms)\n");
+	len += scnprintf(buf + len, PAGE_SIZE - len, "   time(ms)\n");
 
 	for (i = 0; i < max_state; i++) {
+		if (len >= PAGE_SIZE - 1)
+			break;
 		if (df->profile->freq_table[i]
 					== df->previous_freq) {
-			len += sprintf(buf + len, "*");
+			len += scnprintf(buf + len, PAGE_SIZE - len, "*");
 		} else {
-			len += sprintf(buf + len, " ");
+			len += scnprintf(buf + len, PAGE_SIZE - len, " ");
 		}
-		len += sprintf(buf + len, "%10lu:",
-				df->profile->freq_table[i]);
-		for (j = 0; j < max_state; j++)
-			len += sprintf(buf + len, "%10u",
-				df->stats.trans_table[(i * max_state) + j]);
+		if (len >= PAGE_SIZE - 1)
+			break;
+
+		len += scnprintf(buf + len, PAGE_SIZE - len, "%10lu:",
+				 df->profile->freq_table[i]);
+		for (j = 0; j < max_state; j++) {
+			if (len >= PAGE_SIZE - 1)
+				break;
+			len += scnprintf(buf + len, PAGE_SIZE - len, "%10u",
+					 df->stats.trans_table[(i * max_state) + j]);
+		}
+		if (len >= PAGE_SIZE - 1)
+			break;
+		len += scnprintf(buf + len, PAGE_SIZE - len, "%10llu\n", (u64)
+				 jiffies64_to_msecs(df->stats.time_in_state[i]));
+	}
 
-		len += sprintf(buf + len, "%10llu\n", (u64)
-			jiffies64_to_msecs(df->stats.time_in_state[i]));
+	if (len < PAGE_SIZE - 1)
+		len += scnprintf(buf + len, PAGE_SIZE - len, "Total transition : %u\n",
+				 df->stats.total_trans);
+
+	if (len >= PAGE_SIZE - 1) {
+		pr_warn_once("devfreq transition table exceeds PAGE_SIZE. Disabling\n");
+		return -EFBIG;
 	}
 
-	len += sprintf(buf + len, "Total transition : %u\n",
-					df->stats.total_trans);
 	return len;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/devfreq/event/exynos-ppmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/devfreq/event/exynos-ppmu.c
@@ -514,15 +514,19 @@
 
 	count = of_get_child_count(events_np);
 	desc = devm_kcalloc(dev, count, sizeof(*desc), GFP_KERNEL);
-	if (!desc)
+	if (!desc) {
+		of_node_put(events_np);
 		return -ENOMEM;
+	}
 	info->num_events = count;
 
 	of_id = of_match_device(exynos_ppmu_id_match, dev);
 	if (of_id)
 		info->ppmu_type = (enum exynos_ppmu_type)of_id->data;
-	else
+	else {
+		of_node_put(events_np);
 		return -EINVAL;
+	}
 
 	j = 0;
 	for_each_child_of_node(events_np, node) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/devfreq/event/rockchip-dfi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/devfreq/event/rockchip-dfi.c
@@ -194,14 +194,15 @@
 		return PTR_ERR(data->clk);
 	}
 
-	/* try to find the optional reference to the pmu syscon */
 	node = of_parse_phandle(np, "rockchip,pmu", 0);
-	if (node) {
-		data->regmap_pmu = syscon_node_to_regmap(node);
-		of_node_put(node);
-		if (IS_ERR(data->regmap_pmu))
-			return PTR_ERR(data->regmap_pmu);
-	}
+	if (!node)
+		return dev_err_probe(&pdev->dev, -ENODEV, "Can't find pmu_grf registers\n");
+
+	data->regmap_pmu = syscon_node_to_regmap(node);
+	of_node_put(node);
+	if (IS_ERR(data->regmap_pmu))
+		return PTR_ERR(data->regmap_pmu);
+
 	data->dev = dev;
 
 	desc = devm_kzalloc(dev, sizeof(*desc), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/devfreq/governor_userspace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/devfreq/governor_userspace.c
@@ -21,7 +21,7 @@
 
 static int devfreq_userspace_func(struct devfreq *df, unsigned long *freq)
 {
-	struct userspace_data *data = df->data;
+	struct userspace_data *data = df->governor_data;
 
 	if (data->valid)
 		*freq = data->user_frequency;
@@ -40,7 +40,7 @@
 	int err = 0;
 
 	mutex_lock(&devfreq->lock);
-	data = devfreq->data;
+	data = devfreq->governor_data;
 
 	sscanf(buf, "%lu", &wanted);
 	data->user_frequency = wanted;
@@ -60,7 +60,7 @@
 	int err = 0;
 
 	mutex_lock(&devfreq->lock);
-	data = devfreq->data;
+	data = devfreq->governor_data;
 
 	if (data->valid)
 		err = sprintf(buf, "%lu\n", data->user_frequency);
@@ -91,7 +91,7 @@
 		goto out;
 	}
 	data->valid = false;
-	devfreq->data = data;
+	devfreq->governor_data = data;
 
 	err = sysfs_create_group(&devfreq->dev.kobj, &dev_attr_group);
 out:
@@ -107,8 +107,8 @@
 	if (devfreq->dev.kobj.sd)
 		sysfs_remove_group(&devfreq->dev.kobj, &dev_attr_group);
 
-	kfree(devfreq->data);
-	devfreq->data = NULL;
+	kfree(devfreq->governor_data);
+	devfreq->governor_data = NULL;
 }
 
 static int devfreq_userspace_handler(struct devfreq *devfreq,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/devfreq/rk3399_dmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/devfreq/rk3399_dmc.c
@@ -477,6 +477,8 @@
 {
 	struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(&pdev->dev);
 
+	devfreq_event_disable_edev(dmcfreq->edev);
+
 	/*
 	 * Before remove the opp table we need to unregister the opp notifier.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dio/dio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dio/dio.c
@@ -110,6 +110,12 @@
 
 #endif /* CONFIG_DIO_CONSTANTS */
 
+static void dio_dev_release(struct device *dev)
+{
+	struct dio_dev *ddev = container_of(dev, typeof(struct dio_dev), dev);
+	kfree(ddev);
+}
+
 int __init dio_find(int deviceid)
 {
 	/* Called to find a DIO device before the full bus scan has run.
@@ -224,6 +230,7 @@
 		dev->bus = &dio_bus;
 		dev->dev.parent = &dio_bus.dev;
 		dev->dev.bus = &dio_bus_type;
+		dev->dev.release = dio_dev_release;
 		dev->scode = scode;
 		dev->resource.start = pa;
 		dev->resource.end = pa + DIO_SIZE(scode, va);
@@ -251,6 +258,7 @@
 		if (error) {
 			pr_err("DIO: Error registering device %s\n",
 			       dev->name);
+			put_device(&dev->dev);
 			continue;
 		}
 		error = dio_create_sysfs_dev_files(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/dma-buf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/dma-buf.c
@@ -67,14 +67,11 @@
 	BUG_ON(dmabuf->vmapping_counter);
 
 	/*
-	 * Any fences that a dma-buf poll can wait on should be signaled
-	 * before releasing dma-buf. This is the responsibility of each
-	 * driver that uses the reservation objects.
-	 *
-	 * If you hit this BUG() it means someone dropped their ref to the
-	 * dma-buf while still having pending operation to the buffer.
+	 * If you hit this BUG() it could mean:
+	 * * There's a file reference imbalance in dma_buf_poll / dma_buf_poll_cb or somewhere else
+	 * * dmabuf->cb_in/out.active are non-0 despite no pending fence callback
 	 */
-	BUG_ON(dmabuf->cb_shared.active || dmabuf->cb_excl.active);
+	BUG_ON(dmabuf->cb_in.active || dmabuf->cb_out.active);
 
 	dma_buf_stats_teardown(dmabuf);
 	dmabuf->ops->release(dmabuf);
@@ -82,6 +79,7 @@
 	if (dmabuf->resv == (struct dma_resv *)&dmabuf[1])
 		dma_resv_fini(dmabuf->resv);
 
+	WARN_ON(!list_empty(&dmabuf->attachments));
 	module_put(dmabuf->owner);
 	kfree(dmabuf->name);
 	kfree(dmabuf);
@@ -199,22 +197,64 @@
 static void dma_buf_poll_cb(struct dma_fence *fence, struct dma_fence_cb *cb)
 {
 	struct dma_buf_poll_cb_t *dcb = (struct dma_buf_poll_cb_t *)cb;
+	struct dma_buf *dmabuf = container_of(dcb->poll, struct dma_buf, poll);
 	unsigned long flags;
 
 	spin_lock_irqsave(&dcb->poll->lock, flags);
 	wake_up_locked_poll(dcb->poll, dcb->active);
 	dcb->active = 0;
 	spin_unlock_irqrestore(&dcb->poll->lock, flags);
+	dma_fence_put(fence);
+	/* Paired with get_file in dma_buf_poll */
+	fput(dmabuf->file);
+}
+
+static bool dma_buf_poll_shared(struct dma_resv *resv,
+				struct dma_buf_poll_cb_t *dcb)
+{
+	struct dma_resv_list *fobj = dma_resv_shared_list(resv);
+	struct dma_fence *fence;
+	int i, r;
+
+	if (!fobj)
+		return false;
+
+	for (i = 0; i < fobj->shared_count; ++i) {
+		fence = rcu_dereference_protected(fobj->shared[i],
+						  dma_resv_held(resv));
+		dma_fence_get(fence);
+		r = dma_fence_add_callback(fence, &dcb->cb, dma_buf_poll_cb);
+		if (!r)
+			return true;
+		dma_fence_put(fence);
+	}
+
+	return false;
+}
+
+static bool dma_buf_poll_excl(struct dma_resv *resv,
+			      struct dma_buf_poll_cb_t *dcb)
+{
+	struct dma_fence *fence = dma_resv_excl_fence(resv);
+	int r;
+
+	if (!fence)
+		return false;
+
+	dma_fence_get(fence);
+	r = dma_fence_add_callback(fence, &dcb->cb, dma_buf_poll_cb);
+	if (!r)
+		return true;
+	dma_fence_put(fence);
+
+	return false;
 }
 
 static __poll_t dma_buf_poll(struct file *file, poll_table *poll)
 {
 	struct dma_buf *dmabuf;
 	struct dma_resv *resv;
-	struct dma_resv_list *fobj;
-	struct dma_fence *fence_excl;
 	__poll_t events;
-	unsigned shared_count, seq;
 
 	dmabuf = file->private_data;
 	if (!dmabuf || !dmabuf->resv)
@@ -228,101 +268,57 @@
 	if (!events)
 		return 0;
 
-retry:
-	seq = read_seqcount_begin(&resv->seq);
-	rcu_read_lock();
-
-	fobj = rcu_dereference(resv->fence);
-	if (fobj)
-		shared_count = fobj->shared_count;
-	else
-		shared_count = 0;
-	fence_excl = dma_resv_excl_fence(resv);
-	if (read_seqcount_retry(&resv->seq, seq)) {
-		rcu_read_unlock();
-		goto retry;
-	}
-
-	if (fence_excl && (!(events & EPOLLOUT) || shared_count == 0)) {
-		struct dma_buf_poll_cb_t *dcb = &dmabuf->cb_excl;
-		__poll_t pevents = EPOLLIN;
+	dma_resv_lock(resv, NULL);
 
-		if (shared_count == 0)
-			pevents |= EPOLLOUT;
+	if (events & EPOLLOUT) {
+		struct dma_buf_poll_cb_t *dcb = &dmabuf->cb_out;
 
+		/* Check that callback isn't busy */
 		spin_lock_irq(&dmabuf->poll.lock);
-		if (dcb->active) {
-			dcb->active |= pevents;
-			events &= ~pevents;
-		} else
-			dcb->active = pevents;
+		if (dcb->active)
+			events &= ~EPOLLOUT;
+		else
+			dcb->active = EPOLLOUT;
 		spin_unlock_irq(&dmabuf->poll.lock);
 
-		if (events & pevents) {
-			if (!dma_fence_get_rcu(fence_excl)) {
-				/* force a recheck */
-				events &= ~pevents;
-				dma_buf_poll_cb(NULL, &dcb->cb);
-			} else if (!dma_fence_add_callback(fence_excl, &dcb->cb,
-							   dma_buf_poll_cb)) {
-				events &= ~pevents;
-				dma_fence_put(fence_excl);
-			} else {
-				/*
-				 * No callback queued, wake up any additional
-				 * waiters.
-				 */
-				dma_fence_put(fence_excl);
+		if (events & EPOLLOUT) {
+			/* Paired with fput in dma_buf_poll_cb */
+			get_file(dmabuf->file);
+
+			if (!dma_buf_poll_shared(resv, dcb) &&
+			    !dma_buf_poll_excl(resv, dcb))
+
+				/* No callback queued, wake up any other waiters */
 				dma_buf_poll_cb(NULL, &dcb->cb);
-			}
+			else
+				events &= ~EPOLLOUT;
 		}
 	}
 
-	if ((events & EPOLLOUT) && shared_count > 0) {
-		struct dma_buf_poll_cb_t *dcb = &dmabuf->cb_shared;
-		int i;
+	if (events & EPOLLIN) {
+		struct dma_buf_poll_cb_t *dcb = &dmabuf->cb_in;
 
-		/* Only queue a new callback if no event has fired yet */
+		/* Check that callback isn't busy */
 		spin_lock_irq(&dmabuf->poll.lock);
 		if (dcb->active)
-			events &= ~EPOLLOUT;
+			events &= ~EPOLLIN;
 		else
-			dcb->active = EPOLLOUT;
+			dcb->active = EPOLLIN;
 		spin_unlock_irq(&dmabuf->poll.lock);
 
-		if (!(events & EPOLLOUT))
-			goto out;
+		if (events & EPOLLIN) {
+			/* Paired with fput in dma_buf_poll_cb */
+			get_file(dmabuf->file);
 
-		for (i = 0; i < shared_count; ++i) {
-			struct dma_fence *fence = rcu_dereference(fobj->shared[i]);
-
-			if (!dma_fence_get_rcu(fence)) {
-				/*
-				 * fence refcount dropped to zero, this means
-				 * that fobj has been freed
-				 *
-				 * call dma_buf_poll_cb and force a recheck!
-				 */
-				events &= ~EPOLLOUT;
+			if (!dma_buf_poll_excl(resv, dcb))
+				/* No callback queued, wake up any other waiters */
 				dma_buf_poll_cb(NULL, &dcb->cb);
-				break;
-			}
-			if (!dma_fence_add_callback(fence, &dcb->cb,
-						    dma_buf_poll_cb)) {
-				dma_fence_put(fence);
-				events &= ~EPOLLOUT;
-				break;
-			}
-			dma_fence_put(fence);
+			else
+				events &= ~EPOLLIN;
 		}
-
-		/* No callback queued, wake up any additional waiters. */
-		if (i == shared_count)
-			dma_buf_poll_cb(NULL, &dcb->cb);
 	}
 
-out:
-	rcu_read_unlock();
+	dma_resv_unlock(resv);
 	return events;
 }
 
@@ -447,6 +443,7 @@
 
 static struct file *dma_buf_getfile(struct dma_buf *dmabuf, int flags)
 {
+	static atomic64_t dmabuf_inode = ATOMIC64_INIT(0);
 	struct file *file;
 	struct inode *inode = alloc_anon_inode(dma_buf_mnt->mnt_sb);
 
@@ -456,6 +453,13 @@
 	inode->i_size = dmabuf->size;
 	inode_set_bytes(inode, dmabuf->size);
 
+	/*
+	 * The ->i_ino acquired from get_next_ino() is not unique thus
+	 * not suitable for using it as dentry name by dmabuf stats.
+	 * Override ->i_ino with the unique and dmabuffs specific
+	 * value.
+	 */
+	inode->i_ino = atomic64_add_return(1, &dmabuf_inode);
 	file = alloc_file_pseudo(inode, dma_buf_mnt, "dmabuf",
 				 flags, &dma_buf_fops);
 	if (IS_ERR(file))
@@ -565,8 +569,8 @@
 	dmabuf->owner = exp_info->owner;
 	spin_lock_init(&dmabuf->name_lock);
 	init_waitqueue_head(&dmabuf->poll);
-	dmabuf->cb_excl.poll = dmabuf->cb_shared.poll = &dmabuf->poll;
-	dmabuf->cb_excl.active = dmabuf->cb_shared.active = 0;
+	dmabuf->cb_in.poll = dmabuf->cb_out.poll = &dmabuf->poll;
+	dmabuf->cb_in.active = dmabuf->cb_out.active = 0;
 
 	if (!resv) {
 		resv = (struct dma_resv *)&dmabuf[1];
@@ -583,10 +587,6 @@
 	file->f_mode |= FMODE_LSEEK;
 	dmabuf->file = file;
 
-	ret = dma_buf_stats_setup(dmabuf);
-	if (ret)
-		goto err_sysfs;
-
 	mutex_init(&dmabuf->lock);
 	INIT_LIST_HEAD(&dmabuf->attachments);
 
@@ -594,6 +594,10 @@
 	list_add(&dmabuf->list_node, &db_list.head);
 	mutex_unlock(&db_list.lock);
 
+	ret = dma_buf_stats_setup(dmabuf);
+	if (ret)
+		goto err_sysfs;
+
 	return dmabuf;
 
 err_sysfs:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/dma-fence-array.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/dma-fence-array.c
@@ -103,8 +103,38 @@
 static bool dma_fence_array_signaled(struct dma_fence *fence)
 {
 	struct dma_fence_array *array = to_dma_fence_array(fence);
+	int num_pending;
+	unsigned int i;
 
-	return atomic_read(&array->num_pending) <= 0;
+	/*
+	 * We need to read num_pending before checking the enable_signal bit
+	 * to avoid racing with the enable_signaling() implementation, which
+	 * might decrement the counter, and cause a partial check.
+	 * atomic_read_acquire() pairs with atomic_dec_and_test() in
+	 * dma_fence_array_enable_signaling()
+	 *
+	 * The !--num_pending check is here to account for the any_signaled case
+	 * if we race with enable_signaling(), that means the !num_pending check
+	 * in the is_signalling_enabled branch might be outdated (num_pending
+	 * might have been decremented), but that's fine. The user will get the
+	 * right value when testing again later.
+	 */
+	num_pending = atomic_read_acquire(&array->num_pending);
+	if (test_bit(DMA_FENCE_FLAG_ENABLE_SIGNAL_BIT, &array->base.flags)) {
+		if (num_pending <= 0)
+			goto signal;
+		return false;
+	}
+
+	for (i = 0; i < array->num_fences; ++i) {
+		if (dma_fence_is_signaled(array->fences[i]) && !--num_pending)
+			goto signal;
+	}
+	return false;
+
+signal:
+	dma_fence_array_clear_pending_error(array);
+	return true;
 }
 
 static void dma_fence_array_release(struct dma_fence *fence)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/dma-fence-unwrap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/dma-fence-unwrap.c
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * dma-fence-util: misc functions for dma_fence objects
+ *
+ * Copyright (C) 2022 Advanced Micro Devices, Inc.
+ * Authors:
+ *	Christian König <christian.koenig@amd.com>
+ */
+
+#include <linux/dma-fence.h>
+#include <linux/dma-fence-array.h>
+#include <linux/dma-fence-chain.h>
+#include <linux/dma-fence-unwrap.h>
+#include <linux/slab.h>
+
+/* Internal helper to start new array iteration, don't use directly */
+static struct dma_fence *
+__dma_fence_unwrap_array(struct dma_fence_unwrap *cursor)
+{
+	cursor->array = dma_fence_chain_contained(cursor->chain);
+	cursor->index = 0;
+	return dma_fence_array_first(cursor->array);
+}
+
+/**
+ * dma_fence_unwrap_first - return the first fence from fence containers
+ * @head: the entrypoint into the containers
+ * @cursor: current position inside the containers
+ *
+ * Unwraps potential dma_fence_chain/dma_fence_array containers and return the
+ * first fence.
+ */
+struct dma_fence *dma_fence_unwrap_first(struct dma_fence *head,
+					 struct dma_fence_unwrap *cursor)
+{
+	cursor->chain = dma_fence_get(head);
+	return __dma_fence_unwrap_array(cursor);
+}
+EXPORT_SYMBOL_GPL(dma_fence_unwrap_first);
+
+/**
+ * dma_fence_unwrap_next - return the next fence from a fence containers
+ * @cursor: current position inside the containers
+ *
+ * Continue unwrapping the dma_fence_chain/dma_fence_array containers and return
+ * the next fence from them.
+ */
+struct dma_fence *dma_fence_unwrap_next(struct dma_fence_unwrap *cursor)
+{
+	struct dma_fence *tmp;
+
+	++cursor->index;
+	tmp = dma_fence_array_next(cursor->array, cursor->index);
+	if (tmp)
+		return tmp;
+
+	cursor->chain = dma_fence_chain_walk(cursor->chain);
+	return __dma_fence_unwrap_array(cursor);
+}
+EXPORT_SYMBOL_GPL(dma_fence_unwrap_next);
+
+/* Implementation for the dma_fence_merge() marco, don't use directly */
+struct dma_fence *__dma_fence_unwrap_merge(unsigned int num_fences,
+					   struct dma_fence **fences,
+					   struct dma_fence_unwrap *iter)
+{
+	struct dma_fence_array *result;
+	struct dma_fence *tmp, **array;
+	ktime_t timestamp;
+	unsigned int i;
+	size_t count;
+
+	count = 0;
+	timestamp = ns_to_ktime(0);
+	for (i = 0; i < num_fences; ++i) {
+		dma_fence_unwrap_for_each(tmp, &iter[i], fences[i]) {
+			if (!dma_fence_is_signaled(tmp)) {
+				++count;
+			} else {
+				ktime_t t = dma_fence_timestamp(tmp);
+
+				if (ktime_after(t, timestamp))
+					timestamp = t;
+			}
+		}
+	}
+
+	/*
+	 * If we couldn't find a pending fence just return a private signaled
+	 * fence with the timestamp of the last signaled one.
+	 */
+	if (count == 0)
+		return dma_fence_allocate_private_stub(timestamp);
+
+	array = kmalloc_array(count, sizeof(*array), GFP_KERNEL);
+	if (!array)
+		return NULL;
+
+	/*
+	 * This trashes the input fence array and uses it as position for the
+	 * following merge loop. This works because the dma_fence_merge()
+	 * wrapper macro is creating this temporary array on the stack together
+	 * with the iterators.
+	 */
+	for (i = 0; i < num_fences; ++i)
+		fences[i] = dma_fence_unwrap_first(fences[i], &iter[i]);
+
+	count = 0;
+	do {
+		unsigned int sel;
+
+restart:
+		tmp = NULL;
+		for (i = 0; i < num_fences; ++i) {
+			struct dma_fence *next;
+
+			while (fences[i] && dma_fence_is_signaled(fences[i]))
+				fences[i] = dma_fence_unwrap_next(&iter[i]);
+
+			next = fences[i];
+			if (!next)
+				continue;
+
+			/*
+			 * We can't guarantee that inpute fences are ordered by
+			 * context, but it is still quite likely when this
+			 * function is used multiple times. So attempt to order
+			 * the fences by context as we pass over them and merge
+			 * fences with the same context.
+			 */
+			if (!tmp || tmp->context > next->context) {
+				tmp = next;
+				sel = i;
+
+			} else if (tmp->context < next->context) {
+				continue;
+
+			} else if (dma_fence_is_later(tmp, next)) {
+				fences[i] = dma_fence_unwrap_next(&iter[i]);
+				goto restart;
+			} else {
+				fences[sel] = dma_fence_unwrap_next(&iter[sel]);
+				goto restart;
+			}
+		}
+
+		if (tmp) {
+			array[count++] = dma_fence_get(tmp);
+			fences[sel] = dma_fence_unwrap_next(&iter[sel]);
+		}
+	} while (tmp);
+
+	if (count == 0) {
+		tmp = dma_fence_allocate_private_stub(ktime_get());
+		goto return_tmp;
+	}
+
+	if (count == 1) {
+		tmp = array[0];
+		goto return_tmp;
+	}
+
+	result = dma_fence_array_create(count, array,
+					dma_fence_context_alloc(1),
+					1, false);
+	if (!result) {
+		tmp = NULL;
+		goto return_tmp;
+	}
+	return &result->base;
+
+return_tmp:
+	kfree(array);
+	return tmp;
+}
+EXPORT_SYMBOL_GPL(__dma_fence_unwrap_merge);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/dma-heap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/dma-heap.c
@@ -14,6 +14,7 @@
 #include <linux/xarray.h>
 #include <linux/list.h>
 #include <linux/slab.h>
+#include <linux/nospec.h>
 #include <linux/uaccess.h>
 #include <linux/syscalls.h>
 #include <linux/dma-heap.h>
@@ -135,6 +136,7 @@
 	if (nr >= ARRAY_SIZE(dma_heap_ioctl_cmds))
 		return -EINVAL;
 
+	nr = array_index_nospec(nr, ARRAY_SIZE(dma_heap_ioctl_cmds));
 	/* Get the kernel ioctl cmd that matches */
 	kcmd = dma_heap_ioctl_cmds[nr];
 
@@ -231,18 +233,6 @@
 		return ERR_PTR(-EINVAL);
 	}
 
-	/* check the name is unique */
-	mutex_lock(&heap_list_lock);
-	list_for_each_entry(h, &heap_list, list) {
-		if (!strcmp(h->name, exp_info->name)) {
-			mutex_unlock(&heap_list_lock);
-			pr_err("dma_heap: Already registered heap named %s\n",
-			       exp_info->name);
-			return ERR_PTR(-EINVAL);
-		}
-	}
-	mutex_unlock(&heap_list_lock);
-
 	heap = kzalloc(sizeof(*heap), GFP_KERNEL);
 	if (!heap)
 		return ERR_PTR(-ENOMEM);
@@ -281,13 +271,27 @@
 		err_ret = ERR_CAST(dev_ret);
 		goto err2;
 	}
-	/* Add heap to the list */
+
 	mutex_lock(&heap_list_lock);
+	/* check the name is unique */
+	list_for_each_entry(h, &heap_list, list) {
+		if (!strcmp(h->name, exp_info->name)) {
+			mutex_unlock(&heap_list_lock);
+			pr_err("dma_heap: Already registered heap named %s\n",
+			       exp_info->name);
+			err_ret = ERR_PTR(-EINVAL);
+			goto err3;
+		}
+	}
+
+	/* Add heap to the list */
 	list_add(&heap->list, &heap_list);
 	mutex_unlock(&heap_list_lock);
 
 	return heap;
 
+err3:
+	device_destroy(dma_heap_class, heap->heap_devt);
 err2:
 	cdev_del(&heap->heap_cdev);
 err1:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/heaps/cma_heap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/heaps/cma_heap.c
@@ -124,10 +124,11 @@
 	struct cma_heap_buffer *buffer = dmabuf->priv;
 	struct dma_heap_attachment *a;
 
+	mutex_lock(&buffer->lock);
+
 	if (buffer->vmap_cnt)
 		invalidate_kernel_vmap_range(buffer->vaddr, buffer->len);
 
-	mutex_lock(&buffer->lock);
 	list_for_each_entry(a, &buffer->attachments, list) {
 		if (!a->mapped)
 			continue;
@@ -144,10 +145,11 @@
 	struct cma_heap_buffer *buffer = dmabuf->priv;
 	struct dma_heap_attachment *a;
 
+	mutex_lock(&buffer->lock);
+
 	if (buffer->vmap_cnt)
 		flush_kernel_vmap_range(buffer->vaddr, buffer->len);
 
-	mutex_lock(&buffer->lock);
 	list_for_each_entry(a, &buffer->attachments, list) {
 		if (!a->mapped)
 			continue;
@@ -163,7 +165,7 @@
 	struct vm_area_struct *vma = vmf->vma;
 	struct cma_heap_buffer *buffer = vma->vm_private_data;
 
-	if (vmf->pgoff > buffer->pagecount)
+	if (vmf->pgoff >= buffer->pagecount)
 		return VM_FAULT_SIGBUS;
 
 	vmf->page = buffer->pages[vmf->pgoff];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/heaps/system_heap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/heaps/system_heap.c
@@ -289,7 +289,7 @@
 	int i;
 
 	table = &buffer->sg_table;
-	for_each_sg(table->sgl, sg, table->nents, i) {
+	for_each_sgtable_sg(table, sg, i) {
 		struct page *page = sg_page(sg);
 
 		__free_pages(page, compound_order(page));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/sw_sync.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/sw_sync.c
@@ -191,6 +191,7 @@
  */
 static void sync_timeline_signal(struct sync_timeline *obj, unsigned int inc)
 {
+	LIST_HEAD(signalled);
 	struct sync_pt *pt, *next;
 
 	trace_sync_timeline(obj);
@@ -203,21 +204,20 @@
 		if (!timeline_fence_signaled(&pt->base))
 			break;
 
-		list_del_init(&pt->link);
+		dma_fence_get(&pt->base);
+
+		list_move_tail(&pt->link, &signalled);
 		rb_erase(&pt->node, &obj->pt_tree);
 
-		/*
-		 * A signal callback may release the last reference to this
-		 * fence, causing it to be freed. That operation has to be
-		 * last to avoid a use after free inside this loop, and must
-		 * be after we remove the fence from the timeline in order to
-		 * prevent deadlocking on timeline->lock inside
-		 * timeline_fence_release().
-		 */
 		dma_fence_signal_locked(&pt->base);
 	}
 
 	spin_unlock_irq(&obj->lock);
+
+	list_for_each_entry_safe(pt, next, &signalled, link) {
+		list_del_init(&pt->link);
+		dma_fence_put(&pt->base);
+	}
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/sync_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/sync_debug.c
@@ -110,12 +110,12 @@
 
 	seq_printf(s, "%s: %d\n", obj->name, obj->value);
 
-	spin_lock_irq(&obj->lock);
+	spin_lock(&obj->lock); /* Caller already disabled IRQ. */
 	list_for_each(pos, &obj->pt_list) {
 		struct sync_pt *pt = container_of(pos, struct sync_pt, link);
 		sync_print_fence(s, &pt->base, false);
 	}
-	spin_unlock_irq(&obj->lock);
+	spin_unlock(&obj->lock);
 }
 
 static void sync_print_sync_file(struct seq_file *s,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/sync_file.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/sync_file.c
@@ -384,13 +384,10 @@
 		sizeof(info->driver_name));
 
 	info->status = dma_fence_get_status(fence);
-	while (test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags) &&
-	       !test_bit(DMA_FENCE_FLAG_TIMESTAMP_BIT, &fence->flags))
-		cpu_relax();
 	info->timestamp_ns =
-		test_bit(DMA_FENCE_FLAG_TIMESTAMP_BIT, &fence->flags) ?
-		ktime_to_ns(fence->timestamp) :
-		ktime_set(0, 0);
+		dma_fence_is_signaled(fence) ?
+			ktime_to_ns(dma_fence_timestamp(fence)) :
+			ktime_set(0, 0);
 
 	return info->status;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma-buf/udmabuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma-buf/udmabuf.c
@@ -32,8 +32,11 @@
 {
 	struct vm_area_struct *vma = vmf->vma;
 	struct udmabuf *ubuf = vma->vm_private_data;
+	pgoff_t pgoff = vmf->pgoff;
 
-	vmf->page = ubuf->pages[vmf->pgoff];
+	if (pgoff >= ubuf->pagecount)
+		return VM_FAULT_SIGBUS;
+	vmf->page = ubuf->pages[pgoff];
 	get_page(vmf->page);
 	return 0;
 }
@@ -121,17 +124,20 @@
 {
 	struct udmabuf *ubuf = buf->priv;
 	struct device *dev = ubuf->device->this_device;
+	int ret = 0;
 
 	if (!ubuf->sg) {
 		ubuf->sg = get_sg_table(dev, buf, direction);
-		if (IS_ERR(ubuf->sg))
-			return PTR_ERR(ubuf->sg);
+		if (IS_ERR(ubuf->sg)) {
+			ret = PTR_ERR(ubuf->sg);
+			ubuf->sg = NULL;
+		}
 	} else {
 		dma_sync_sg_for_cpu(dev, ubuf->sg->sgl, ubuf->sg->nents,
 				    direction);
 	}
 
-	return 0;
+	return ret;
 }
 
 static int end_cpu_udmabuf(struct dma_buf *buf,
@@ -158,7 +164,7 @@
 };
 
 #define SEALS_WANTED (F_SEAL_SHRINK)
-#define SEALS_DENIED (F_SEAL_WRITE)
+#define SEALS_DENIED (F_SEAL_WRITE|F_SEAL_FUTURE_WRITE)
 
 static long udmabuf_create(struct miscdevice *device,
 			   struct udmabuf_create_list *head,
@@ -190,6 +196,10 @@
 		if (ubuf->pagecount > pglimit)
 			goto err;
 	}
+
+	if (!ubuf->pagecount)
+		goto err;
+
 	ubuf->pages = kmalloc_array(ubuf->pagecount, sizeof(*ubuf->pages),
 				    GFP_KERNEL);
 	if (!ubuf->pages) {
@@ -361,7 +371,23 @@
 
 static int __init udmabuf_dev_init(void)
 {
-	return misc_register(&udmabuf_misc);
+	int ret;
+
+	ret = misc_register(&udmabuf_misc);
+	if (ret < 0) {
+		pr_err("Could not initialize udmabuf device\n");
+		return ret;
+	}
+
+	ret = dma_coerce_mask_and_coherent(udmabuf_misc.this_device,
+					   DMA_BIT_MASK(64));
+	if (ret < 0) {
+		pr_err("Could not setup DMA mask for udmabuf device\n");
+		misc_deregister(&udmabuf_misc);
+		return ret;
+	}
+
+	return 0;
 }
 
 static void __exit udmabuf_dev_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/Kconfig
@@ -202,6 +202,7 @@
 config FSL_EDMA
 	tristate "Freescale eDMA engine support"
 	depends on OF
+	depends on HAS_IOMEM
 	select DMA_ENGINE
 	select DMA_VIRTUAL_CHANNELS
 	help
@@ -236,7 +237,7 @@
 
 config HISI_DMA
 	tristate "HiSilicon DMA Engine support"
-	depends on ARM64 || COMPILE_TEST
+	depends on ARCH_HISI || COMPILE_TEST
 	depends on PCI_MSI
 	select DMA_ENGINE
 	select DMA_VIRTUAL_CHANNELS
@@ -271,6 +272,7 @@
 
 config INTEL_IDMA64
 	tristate "Intel integrated DMA 64-bit support"
+	depends on HAS_IOMEM
 	select DMA_ENGINE
 	select DMA_VIRTUAL_CHANNELS
 	help
@@ -643,16 +645,16 @@
 
 config TEGRA210_ADMA
 	tristate "NVIDIA Tegra210 ADMA support"
-	depends on (ARCH_TEGRA_210_SOC || COMPILE_TEST)
+	depends on (ARCH_TEGRA || COMPILE_TEST)
 	select DMA_ENGINE
 	select DMA_VIRTUAL_CHANNELS
 	help
-	  Support for the NVIDIA Tegra210 ADMA controller driver. The
-	  DMA controller has multiple DMA channels and is used to service
-	  various audio clients in the Tegra210 audio processing engine
-	  (APE). This DMA controller transfers data from memory to
-	  peripheral and vice versa. It does not support memory to
-	  memory data transfer.
+	  Support for the NVIDIA Tegra210/Tegra186/Tegra194/Tegra234 ADMA
+	  controller driver. The DMA controller has multiple DMA channels
+	  and is used to service various audio clients in the Tegra210
+	  audio processing engine (APE). This DMA controller transfers
+	  data from memory to peripheral and vice versa. It does not
+	  support memory to memory data transfer.
 
 config TIMB_DMA
 	tristate "Timberdale FPGA DMA support"
@@ -733,6 +735,35 @@
 	  driver provides the dmaengine required by the DisplayPort subsystem
 	  display driver.
 
+config XILINX_FRMBUF
+	tristate "Xilinx Framebuffer"
+	select DMA_ENGINE
+	help
+	 Enable support for Xilinx Framebuffer DMA.
+
+config XILINX_PS_PCIE_DMA
+	tristate "Xilinx PS PCIe DMA support"
+	depends on (PCI && X86_64 || ARM64)
+	select DMA_ENGINE
+	help
+	  Enable support for the Xilinx PS PCIe DMA engine present
+	  in recent Xilinx ZynqMP chipsets.
+
+	  Say Y here if you have such a chipset.
+
+	  If unsure, say N.
+
+config XILINX_PS_PCIE_DMA_TEST
+	tristate "Xilinx PS PCIe DMA test client"
+	depends on XILINX_PS_PCIE_DMA
+	help
+	  Enable support for the test client of Xilinx PS PCIe DMA engine
+	  in recent Xilinx ZynqMP chipsets.
+
+	  Say Y here if you have such a chipset.
+
+	  If unsure, say N.
+
 # driver files
 source "drivers/dma/bestcomm/Kconfig"
 
@@ -784,4 +815,18 @@
 config DMA_ENGINE_RAID
 	bool
 
+config XILINX_DMATEST
+	tristate "DMA Test client for AXI DMA and MCDMA"
+	depends on XILINX_DMA
+	help
+	  Simple DMA test client. Say N unless you're debugging a
+	  DMA Device driver.
+
+config XILINX_VDMATEST
+	tristate "DMA Test client for VDMA"
+	depends on XILINX_DMA
+	help
+	  Simple xilinx VDMA test client. Say N unless you're debugging a
+	  DMA Device driver.
+
 endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/at_hdmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/at_hdmac.c
@@ -256,6 +256,8 @@
 		       ATC_SPIP_BOUNDARY(first->boundary));
 	channel_writel(atchan, DPIP, ATC_DPIP_HOLE(first->dst_hole) |
 		       ATC_DPIP_BOUNDARY(first->boundary));
+	/* Don't allow CPU to reorder channel enable. */
+	wmb();
 	dma_writel(atdma, CHER, atchan->mask);
 
 	vdbg_dump_regs(atchan);
@@ -316,7 +318,8 @@
 	struct at_desc *desc_first = atc_first_active(atchan);
 	struct at_desc *desc;
 	int ret;
-	u32 ctrla, dscr, trials;
+	u32 ctrla, dscr;
+	unsigned int i;
 
 	/*
 	 * If the cookie doesn't match to the currently running transfer then
@@ -386,7 +389,7 @@
 		dscr = channel_readl(atchan, DSCR);
 		rmb(); /* ensure DSCR is read before CTRLA */
 		ctrla = channel_readl(atchan, CTRLA);
-		for (trials = 0; trials < ATC_MAX_DSCR_TRIALS; ++trials) {
+		for (i = 0; i < ATC_MAX_DSCR_TRIALS; ++i) {
 			u32 new_dscr;
 
 			rmb(); /* ensure DSCR is read after CTRLA */
@@ -412,7 +415,7 @@
 			rmb(); /* ensure DSCR is read before CTRLA */
 			ctrla = channel_readl(atchan, CTRLA);
 		}
-		if (unlikely(trials >= ATC_MAX_DSCR_TRIALS))
+		if (unlikely(i == ATC_MAX_DSCR_TRIALS))
 			return -ETIMEDOUT;
 
 		/* for the first descriptor we can be more accurate */
@@ -462,18 +465,6 @@
 	if (!atc_chan_is_cyclic(atchan))
 		dma_cookie_complete(txd);
 
-	/* If the transfer was a memset, free our temporary buffer */
-	if (desc->memset_buffer) {
-		dma_pool_free(atdma->memset_pool, desc->memset_vaddr,
-			      desc->memset_paddr);
-		desc->memset_buffer = false;
-	}
-
-	/* move children to free_list */
-	list_splice_init(&desc->tx_list, &atchan->free_list);
-	/* move myself to free_list */
-	list_move(&desc->desc_node, &atchan->free_list);
-
 	spin_unlock_irqrestore(&atchan->lock, flags);
 
 	dma_descriptor_unmap(txd);
@@ -483,42 +474,20 @@
 		dmaengine_desc_get_callback_invoke(txd, NULL);
 
 	dma_run_dependencies(txd);
-}
-
-/**
- * atc_complete_all - finish work for all transactions
- * @atchan: channel to complete transactions for
- *
- * Eventually submit queued descriptors if any
- *
- * Assume channel is idle while calling this function
- * Called with atchan->lock held and bh disabled
- */
-static void atc_complete_all(struct at_dma_chan *atchan)
-{
-	struct at_desc *desc, *_desc;
-	LIST_HEAD(list);
-	unsigned long flags;
-
-	dev_vdbg(chan2dev(&atchan->chan_common), "complete all\n");
 
 	spin_lock_irqsave(&atchan->lock, flags);
-
-	/*
-	 * Submit queued descriptors ASAP, i.e. before we go through
-	 * the completed ones.
-	 */
-	if (!list_empty(&atchan->queue))
-		atc_dostart(atchan, atc_first_queued(atchan));
-	/* empty active_list now it is completed */
-	list_splice_init(&atchan->active_list, &list);
-	/* empty queue list by moving descriptors (if any) to active_list */
-	list_splice_init(&atchan->queue, &atchan->active_list);
-
+	/* move children to free_list */
+	list_splice_init(&desc->tx_list, &atchan->free_list);
+	/* add myself to free_list */
+	list_add(&desc->desc_node, &atchan->free_list);
 	spin_unlock_irqrestore(&atchan->lock, flags);
 
-	list_for_each_entry_safe(desc, _desc, &list, desc_node)
-		atc_chain_complete(atchan, desc);
+	/* If the transfer was a memset, free our temporary buffer */
+	if (desc->memset_buffer) {
+		dma_pool_free(atdma->memset_pool, desc->memset_vaddr,
+			      desc->memset_paddr);
+		desc->memset_buffer = false;
+	}
 }
 
 /**
@@ -527,26 +496,28 @@
  */
 static void atc_advance_work(struct at_dma_chan *atchan)
 {
+	struct at_desc *desc;
 	unsigned long flags;
-	int ret;
 
 	dev_vdbg(chan2dev(&atchan->chan_common), "advance_work\n");
 
 	spin_lock_irqsave(&atchan->lock, flags);
-	ret = atc_chan_is_enabled(atchan);
-	spin_unlock_irqrestore(&atchan->lock, flags);
-	if (ret)
-		return;
-
-	if (list_empty(&atchan->active_list) ||
-	    list_is_singular(&atchan->active_list))
-		return atc_complete_all(atchan);
+	if (atc_chan_is_enabled(atchan) || list_empty(&atchan->active_list))
+		return spin_unlock_irqrestore(&atchan->lock, flags);
 
-	atc_chain_complete(atchan, atc_first_active(atchan));
+	desc = atc_first_active(atchan);
+	/* Remove the transfer node from the active list. */
+	list_del_init(&desc->desc_node);
+	spin_unlock_irqrestore(&atchan->lock, flags);
+	atc_chain_complete(atchan, desc);
 
 	/* advance work */
 	spin_lock_irqsave(&atchan->lock, flags);
-	atc_dostart(atchan, atc_first_active(atchan));
+	if (!list_empty(&atchan->active_list)) {
+		desc = atc_first_queued(atchan);
+		list_move_tail(&desc->desc_node, &atchan->active_list);
+		atc_dostart(atchan, desc);
+	}
 	spin_unlock_irqrestore(&atchan->lock, flags);
 }
 
@@ -558,6 +529,7 @@
 static void atc_handle_error(struct at_dma_chan *atchan)
 {
 	struct at_desc *bad_desc;
+	struct at_desc *desc;
 	struct at_desc *child;
 	unsigned long flags;
 
@@ -570,13 +542,12 @@
 	bad_desc = atc_first_active(atchan);
 	list_del_init(&bad_desc->desc_node);
 
-	/* As we are stopped, take advantage to push queued descriptors
-	 * in active_list */
-	list_splice_init(&atchan->queue, atchan->active_list.prev);
-
 	/* Try to restart the controller */
-	if (!list_empty(&atchan->active_list))
-		atc_dostart(atchan, atc_first_active(atchan));
+	if (!list_empty(&atchan->active_list)) {
+		desc = atc_first_queued(atchan);
+		list_move_tail(&desc->desc_node, &atchan->active_list);
+		atc_dostart(atchan, desc);
+	}
 
 	/*
 	 * KERN_CRITICAL may seem harsh, but since this only happens
@@ -691,19 +662,11 @@
 	spin_lock_irqsave(&atchan->lock, flags);
 	cookie = dma_cookie_assign(tx);
 
-	if (list_empty(&atchan->active_list)) {
-		dev_vdbg(chan2dev(tx->chan), "tx_submit: started %u\n",
-				desc->txd.cookie);
-		atc_dostart(atchan, desc);
-		list_add_tail(&desc->desc_node, &atchan->active_list);
-	} else {
-		dev_vdbg(chan2dev(tx->chan), "tx_submit: queued %u\n",
-				desc->txd.cookie);
-		list_add_tail(&desc->desc_node, &atchan->queue);
-	}
-
+	list_add_tail(&desc->desc_node, &atchan->queue);
 	spin_unlock_irqrestore(&atchan->lock, flags);
 
+	dev_vdbg(chan2dev(tx->chan), "tx_submit: queued %u\n",
+		 desc->txd.cookie);
 	return cookie;
 }
 
@@ -1437,11 +1400,8 @@
 	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
 	struct at_dma		*atdma = to_at_dma(chan->device);
 	int			chan_id = atchan->chan_common.chan_id;
-	struct at_desc		*desc, *_desc;
 	unsigned long		flags;
 
-	LIST_HEAD(list);
-
 	dev_vdbg(chan2dev(chan), "%s\n", __func__);
 
 	/*
@@ -1460,19 +1420,15 @@
 		cpu_relax();
 
 	/* active_list entries will end up before queued entries */
-	list_splice_init(&atchan->queue, &list);
-	list_splice_init(&atchan->active_list, &list);
-
-	spin_unlock_irqrestore(&atchan->lock, flags);
-
-	/* Flush all pending and queued descriptors */
-	list_for_each_entry_safe(desc, _desc, &list, desc_node)
-		atc_chain_complete(atchan, desc);
+	list_splice_tail_init(&atchan->queue, &atchan->free_list);
+	list_splice_tail_init(&atchan->active_list, &atchan->free_list);
 
 	clear_bit(ATC_IS_PAUSED, &atchan->status);
 	/* if channel dedicated to cyclic operations, free it */
 	clear_bit(ATC_IS_CYCLIC, &atchan->status);
 
+	spin_unlock_irqrestore(&atchan->lock, flags);
+
 	return 0;
 }
 
@@ -1527,20 +1483,26 @@
 }
 
 /**
- * atc_issue_pending - try to finish work
+ * atc_issue_pending - takes the first transaction descriptor in the pending
+ * queue and starts the transfer.
  * @chan: target DMA channel
  */
 static void atc_issue_pending(struct dma_chan *chan)
 {
-	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	struct at_dma_chan *atchan = to_at_dma_chan(chan);
+	struct at_desc *desc;
+	unsigned long flags;
 
 	dev_vdbg(chan2dev(chan), "issue_pending\n");
 
-	/* Not needed for cyclic transfers */
-	if (atc_chan_is_cyclic(atchan))
-		return;
+	spin_lock_irqsave(&atchan->lock, flags);
+	if (atc_chan_is_enabled(atchan) || list_empty(&atchan->queue))
+		return spin_unlock_irqrestore(&atchan->lock, flags);
 
-	atc_advance_work(atchan);
+	desc = atc_first_queued(atchan);
+	list_move_tail(&desc->desc_node, &atchan->active_list);
+	atc_dostart(atchan, desc);
+	spin_unlock_irqrestore(&atchan->lock, flags);
 }
 
 /**
@@ -1958,7 +1920,11 @@
 	  dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)  ? "slave " : "",
 	  plat_dat->nr_channels);
 
-	dma_async_device_register(&atdma->dma_common);
+	err = dma_async_device_register(&atdma->dma_common);
+	if (err) {
+		dev_err(&pdev->dev, "Unable to register: %d.\n", err);
+		goto err_dma_async_device_register;
+	}
 
 	/*
 	 * Do not return an error if the dmac node is not present in order to
@@ -1978,6 +1944,7 @@
 
 err_of_dma_controller_register:
 	dma_async_device_unregister(&atdma->dma_common);
+err_dma_async_device_register:
 	dma_pool_destroy(atdma->memset_pool);
 err_memset_pool_create:
 	dma_pool_destroy(atdma->dma_desc_pool);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/at_hdmac_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/at_hdmac_regs.h
@@ -186,13 +186,13 @@
 /* LLI == Linked List Item; aka DMA buffer descriptor */
 struct at_lli {
 	/* values that are not changed by hardware */
-	dma_addr_t	saddr;
-	dma_addr_t	daddr;
+	u32 saddr;
+	u32 daddr;
 	/* value that may get written back: */
-	u32		ctrla;
+	u32 ctrla;
 	/* more values that are not changed by hardware */
-	u32		ctrlb;
-	dma_addr_t	dscr;	/* chain to next lli */
+	u32 ctrlb;
+	u32 dscr;	/* chain to next lli */
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/at_xdmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/at_xdmac.c
@@ -99,6 +99,7 @@
 #define		AT_XDMAC_CNDC_NDE		(0x1 << 0)		/* Channel x Next Descriptor Enable */
 #define		AT_XDMAC_CNDC_NDSUP		(0x1 << 1)		/* Channel x Next Descriptor Source Update */
 #define		AT_XDMAC_CNDC_NDDUP		(0x1 << 2)		/* Channel x Next Descriptor Destination Update */
+#define		AT_XDMAC_CNDC_NDVIEW_MASK	GENMASK(28, 27)
 #define		AT_XDMAC_CNDC_NDVIEW_NDV0	(0x0 << 3)		/* Channel x Next Descriptor View 0 */
 #define		AT_XDMAC_CNDC_NDVIEW_NDV1	(0x1 << 3)		/* Channel x Next Descriptor View 1 */
 #define		AT_XDMAC_CNDC_NDVIEW_NDV2	(0x2 << 3)		/* Channel x Next Descriptor View 2 */
@@ -155,7 +156,7 @@
 #define		AT_XDMAC_CC_WRIP	(0x1 << 23)	/* Write in Progress (read only) */
 #define			AT_XDMAC_CC_WRIP_DONE		(0x0 << 23)
 #define			AT_XDMAC_CC_WRIP_IN_PROGRESS	(0x1 << 23)
-#define		AT_XDMAC_CC_PERID(i)	(0x7f & (i) << 24)	/* Channel Peripheral Identifier */
+#define		AT_XDMAC_CC_PERID(i)	((0x7f & (i)) << 24)	/* Channel Peripheral Identifier */
 #define AT_XDMAC_CDS_MSP	0x2C	/* Channel Data Stride Memory Set Pattern */
 #define AT_XDMAC_CSUS		0x30	/* Channel Source Microblock Stride */
 #define AT_XDMAC_CDUS		0x34	/* Channel Destination Microblock Stride */
@@ -242,6 +243,7 @@
 	int			irq;
 	struct clk		*clk;
 	u32			save_gim;
+	u32			save_gs;
 	struct dma_pool		*at_xdmac_desc_pool;
 	const struct at_xdmac_layout	*layout;
 	struct at_xdmac_chan	chan[];
@@ -252,15 +254,15 @@
 
 /* Linked List Descriptor */
 struct at_xdmac_lld {
-	dma_addr_t	mbr_nda;	/* Next Descriptor Member */
-	u32		mbr_ubc;	/* Microblock Control Member */
-	dma_addr_t	mbr_sa;		/* Source Address Member */
-	dma_addr_t	mbr_da;		/* Destination Address Member */
-	u32		mbr_cfg;	/* Configuration Register */
-	u32		mbr_bc;		/* Block Control Register */
-	u32		mbr_ds;		/* Data Stride Register */
-	u32		mbr_sus;	/* Source Microblock Stride Register */
-	u32		mbr_dus;	/* Destination Microblock Stride Register */
+	u32 mbr_nda;	/* Next Descriptor Member */
+	u32 mbr_ubc;	/* Microblock Control Member */
+	u32 mbr_sa;	/* Source Address Member */
+	u32 mbr_da;	/* Destination Address Member */
+	u32 mbr_cfg;	/* Configuration Register */
+	u32 mbr_bc;	/* Block Control Register */
+	u32 mbr_ds;	/* Data Stride Register */
+	u32 mbr_sus;	/* Source Microblock Stride Register */
+	u32 mbr_dus;	/* Destination Microblock Stride Register */
 };
 
 /* 64-bit alignment needed to update CNDA and CUBC registers in an atomic way. */
@@ -385,9 +387,6 @@
 
 	dev_vdbg(chan2dev(&atchan->chan), "%s: desc 0x%p\n", __func__, first);
 
-	if (at_xdmac_chan_is_enabled(atchan))
-		return;
-
 	/* Set transfer as active to not try to start it again. */
 	first->active_xfer = true;
 
@@ -405,7 +404,8 @@
 	 */
 	if (at_xdmac_chan_is_cyclic(atchan))
 		reg = AT_XDMAC_CNDC_NDVIEW_NDV1;
-	else if (first->lld.mbr_ubc & AT_XDMAC_MBR_UBC_NDV3)
+	else if ((first->lld.mbr_ubc &
+		  AT_XDMAC_CNDC_NDVIEW_MASK) == AT_XDMAC_MBR_UBC_NDV3)
 		reg = AT_XDMAC_CNDC_NDVIEW_NDV3;
 	else
 		reg = AT_XDMAC_CNDC_NDVIEW_NDV2;
@@ -476,13 +476,12 @@
 	spin_lock_irqsave(&atchan->lock, irqflags);
 	cookie = dma_cookie_assign(tx);
 
+	list_add_tail(&desc->xfer_node, &atchan->xfers_list);
+	spin_unlock_irqrestore(&atchan->lock, irqflags);
+
 	dev_vdbg(chan2dev(tx->chan), "%s: atchan 0x%p, add desc 0x%p to xfers_list\n",
 		 __func__, atchan, desc);
-	list_add_tail(&desc->xfer_node, &atchan->xfers_list);
-	if (list_is_singular(&atchan->xfers_list))
-		at_xdmac_start_xfer(atchan, desc);
 
-	spin_unlock_irqrestore(&atchan->lock, irqflags);
 	return cookie;
 }
 
@@ -733,7 +732,8 @@
 		if (!desc) {
 			dev_err(chan2dev(chan), "can't get descriptor\n");
 			if (first)
-				list_splice_init(&first->descs_list, &atchan->free_descs_list);
+				list_splice_tail_init(&first->descs_list,
+						      &atchan->free_descs_list);
 			goto spin_unlock;
 		}
 
@@ -821,7 +821,8 @@
 		if (!desc) {
 			dev_err(chan2dev(chan), "can't get descriptor\n");
 			if (first)
-				list_splice_init(&first->descs_list, &atchan->free_descs_list);
+				list_splice_tail_init(&first->descs_list,
+						      &atchan->free_descs_list);
 			spin_unlock_irqrestore(&atchan->lock, irqflags);
 			return NULL;
 		}
@@ -1025,6 +1026,8 @@
 							NULL,
 							src_addr, dst_addr,
 							xt, xt->sgl);
+		if (!first)
+			return NULL;
 
 		/* Length of the block is (BLEN+1) microblocks. */
 		for (i = 0; i < xt->numf - 1; i++)
@@ -1055,8 +1058,9 @@
 							       src_addr, dst_addr,
 							       xt, chunk);
 			if (!desc) {
-				list_splice_init(&first->descs_list,
-						 &atchan->free_descs_list);
+				if (first)
+					list_splice_tail_init(&first->descs_list,
+							      &atchan->free_descs_list);
 				return NULL;
 			}
 
@@ -1136,7 +1140,8 @@
 		if (!desc) {
 			dev_err(chan2dev(chan), "can't get descriptor\n");
 			if (first)
-				list_splice_init(&first->descs_list, &atchan->free_descs_list);
+				list_splice_tail_init(&first->descs_list,
+						      &atchan->free_descs_list);
 			return NULL;
 		}
 
@@ -1275,6 +1280,8 @@
 		return NULL;
 
 	desc = at_xdmac_memset_create_desc(chan, atchan, dest, len, value);
+	if (!desc)
+		return NULL;
 	list_add_tail(&desc->desc_node, &desc->descs_list);
 
 	desc->tx_dma_desc.cookie = -EBUSY;
@@ -1312,8 +1319,8 @@
 						   sg_dma_len(sg),
 						   value);
 		if (!desc && first)
-			list_splice_init(&first->descs_list,
-					 &atchan->free_descs_list);
+			list_splice_tail_init(&first->descs_list,
+					      &atchan->free_descs_list);
 
 		if (!first)
 			first = desc;
@@ -1452,7 +1459,7 @@
 {
 	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
 	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
-	struct at_xdmac_desc	*desc, *_desc;
+	struct at_xdmac_desc	*desc, *_desc, *iter;
 	struct list_head	*descs_list;
 	enum dma_status		ret;
 	int			residue, retry;
@@ -1567,11 +1574,13 @@
 	 * microblock.
 	 */
 	descs_list = &desc->descs_list;
-	list_for_each_entry_safe(desc, _desc, descs_list, desc_node) {
-		dwidth = at_xdmac_get_dwidth(desc->lld.mbr_cfg);
-		residue -= (desc->lld.mbr_ubc & 0xffffff) << dwidth;
-		if ((desc->lld.mbr_nda & 0xfffffffc) == cur_nda)
+	list_for_each_entry_safe(iter, _desc, descs_list, desc_node) {
+		dwidth = at_xdmac_get_dwidth(iter->lld.mbr_cfg);
+		residue -= (iter->lld.mbr_ubc & 0xffffff) << dwidth;
+		if ((iter->lld.mbr_nda & 0xfffffffc) == cur_nda) {
+			desc = iter;
 			break;
+		}
 	}
 	residue += cur_ubc << dwidth;
 
@@ -1586,20 +1595,6 @@
 	return ret;
 }
 
-/* Call must be protected by lock. */
-static void at_xdmac_remove_xfer(struct at_xdmac_chan *atchan,
-				    struct at_xdmac_desc *desc)
-{
-	dev_dbg(chan2dev(&atchan->chan), "%s: desc 0x%p\n", __func__, desc);
-
-	/*
-	 * Remove the transfer from the transfer list then move the transfer
-	 * descriptors into the free descriptors list.
-	 */
-	list_del(&desc->xfer_node);
-	list_splice_init(&desc->descs_list, &atchan->free_descs_list);
-}
-
 static void at_xdmac_advance_work(struct at_xdmac_chan *atchan)
 {
 	struct at_xdmac_desc	*desc;
@@ -1623,14 +1618,17 @@
 	struct at_xdmac_desc		*desc;
 	struct dma_async_tx_descriptor	*txd;
 
-	if (!list_empty(&atchan->xfers_list)) {
-		desc = list_first_entry(&atchan->xfers_list,
-					struct at_xdmac_desc, xfer_node);
-		txd = &desc->tx_dma_desc;
-
-		if (txd->flags & DMA_PREP_INTERRUPT)
-			dmaengine_desc_get_callback_invoke(txd, NULL);
+	spin_lock_irq(&atchan->lock);
+	if (list_empty(&atchan->xfers_list)) {
+		spin_unlock_irq(&atchan->lock);
+		return;
 	}
+	desc = list_first_entry(&atchan->xfers_list, struct at_xdmac_desc,
+				xfer_node);
+	spin_unlock_irq(&atchan->lock);
+	txd = &desc->tx_dma_desc;
+	if (txd->flags & DMA_PREP_INTERRUPT)
+		dmaengine_desc_get_callback_invoke(txd, NULL);
 }
 
 static void at_xdmac_handle_error(struct at_xdmac_chan *atchan)
@@ -1707,17 +1705,20 @@
 		}
 
 		txd = &desc->tx_dma_desc;
-
-		at_xdmac_remove_xfer(atchan, desc);
+		dma_cookie_complete(txd);
+		/* Remove the transfer from the transfer list. */
+		list_del(&desc->xfer_node);
 		spin_unlock_irq(&atchan->lock);
 
-		dma_cookie_complete(txd);
 		if (txd->flags & DMA_PREP_INTERRUPT)
 			dmaengine_desc_get_callback_invoke(txd, NULL);
 
 		dma_run_dependencies(txd);
 
 		spin_lock_irq(&atchan->lock);
+		/* Move the xfer descriptors into the free descriptors list. */
+		list_splice_tail_init(&desc->descs_list,
+				      &atchan->free_descs_list);
 		at_xdmac_advance_work(atchan);
 		spin_unlock_irq(&atchan->lock);
 	}
@@ -1784,11 +1785,9 @@
 
 	dev_dbg(chan2dev(&atchan->chan), "%s\n", __func__);
 
-	if (!at_xdmac_chan_is_cyclic(atchan)) {
-		spin_lock_irqsave(&atchan->lock, flags);
-		at_xdmac_advance_work(atchan);
-		spin_unlock_irqrestore(&atchan->lock, flags);
-	}
+	spin_lock_irqsave(&atchan->lock, flags);
+	at_xdmac_advance_work(atchan);
+	spin_unlock_irqrestore(&atchan->lock, flags);
 
 	return;
 }
@@ -1866,8 +1865,11 @@
 		cpu_relax();
 
 	/* Cancel all pending transfers. */
-	list_for_each_entry_safe(desc, _desc, &atchan->xfers_list, xfer_node)
-		at_xdmac_remove_xfer(atchan, desc);
+	list_for_each_entry_safe(desc, _desc, &atchan->xfers_list, xfer_node) {
+		list_del(&desc->xfer_node);
+		list_splice_tail_init(&desc->descs_list,
+				      &atchan->free_descs_list);
+	}
 
 	clear_bit(AT_XDMAC_CHAN_IS_PAUSED, &atchan->status);
 	clear_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status);
@@ -1897,6 +1899,11 @@
 	for (i = 0; i < init_nr_desc_per_channel; i++) {
 		desc = at_xdmac_alloc_desc(chan, GFP_KERNEL);
 		if (!desc) {
+			if (i == 0) {
+				dev_warn(chan2dev(chan),
+					 "can't allocate any descriptors\n");
+				return -EIO;
+			}
 			dev_warn(chan2dev(chan),
 				"only %d descriptors have been allocated\n", i);
 			break;
@@ -1926,6 +1933,30 @@
 	return;
 }
 
+static void at_xdmac_axi_config(struct platform_device *pdev)
+{
+	struct at_xdmac	*atxdmac = (struct at_xdmac *)platform_get_drvdata(pdev);
+	bool dev_m2m = false;
+	u32 dma_requests;
+
+	if (!atxdmac->layout->axi_config)
+		return; /* Not supported */
+
+	if (!of_property_read_u32(pdev->dev.of_node, "dma-requests",
+				  &dma_requests)) {
+		dev_info(&pdev->dev, "controller in mem2mem mode.\n");
+		dev_m2m = true;
+	}
+
+	if (dev_m2m) {
+		at_xdmac_write(atxdmac, AT_XDMAC_GCFG, AT_XDMAC_GCFG_M2M);
+		at_xdmac_write(atxdmac, AT_XDMAC_GWAC, AT_XDMAC_GWAC_M2M);
+	} else {
+		at_xdmac_write(atxdmac, AT_XDMAC_GCFG, AT_XDMAC_GCFG_P2M);
+		at_xdmac_write(atxdmac, AT_XDMAC_GWAC, AT_XDMAC_GWAC_P2M);
+	}
+}
+
 #ifdef CONFIG_PM
 static int atmel_xdmac_prepare(struct device *dev)
 {
@@ -1964,6 +1995,7 @@
 		}
 	}
 	atxdmac->save_gim = at_xdmac_read(atxdmac, AT_XDMAC_GIM);
+	atxdmac->save_gs = at_xdmac_read(atxdmac, AT_XDMAC_GS);
 
 	at_xdmac_off(atxdmac);
 	clk_disable_unprepare(atxdmac->clk);
@@ -1975,6 +2007,7 @@
 	struct at_xdmac		*atxdmac = dev_get_drvdata(dev);
 	struct at_xdmac_chan	*atchan;
 	struct dma_chan		*chan, *_chan;
+	struct platform_device	*pdev = container_of(dev, struct platform_device, dev);
 	int			i;
 	int ret;
 
@@ -1982,6 +2015,8 @@
 	if (ret)
 		return ret;
 
+	at_xdmac_axi_config(pdev);
+
 	/* Clear pending interrupts. */
 	for (i = 0; i < atxdmac->dma.chancnt; i++) {
 		atchan = &atxdmac->chan[i];
@@ -2000,37 +2035,14 @@
 			at_xdmac_chan_write(atchan, AT_XDMAC_CNDC, atchan->save_cndc);
 			at_xdmac_chan_write(atchan, AT_XDMAC_CIE, atchan->save_cim);
 			wmb();
-			at_xdmac_write(atxdmac, AT_XDMAC_GE, atchan->mask);
+			if (atxdmac->save_gs & atchan->mask)
+				at_xdmac_write(atxdmac, AT_XDMAC_GE, atchan->mask);
 		}
 	}
 	return 0;
 }
 #endif /* CONFIG_PM_SLEEP */
 
-static void at_xdmac_axi_config(struct platform_device *pdev)
-{
-	struct at_xdmac	*atxdmac = (struct at_xdmac *)platform_get_drvdata(pdev);
-	bool dev_m2m = false;
-	u32 dma_requests;
-
-	if (!atxdmac->layout->axi_config)
-		return; /* Not supported */
-
-	if (!of_property_read_u32(pdev->dev.of_node, "dma-requests",
-				  &dma_requests)) {
-		dev_info(&pdev->dev, "controller in mem2mem mode.\n");
-		dev_m2m = true;
-	}
-
-	if (dev_m2m) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GCFG, AT_XDMAC_GCFG_M2M);
-		at_xdmac_write(atxdmac, AT_XDMAC_GWAC, AT_XDMAC_GWAC_M2M);
-	} else {
-		at_xdmac_write(atxdmac, AT_XDMAC_GCFG, AT_XDMAC_GCFG_P2M);
-		at_xdmac_write(atxdmac, AT_XDMAC_GWAC, AT_XDMAC_GWAC_P2M);
-	}
-}
-
 static int at_xdmac_probe(struct platform_device *pdev)
 {
 	struct at_xdmac	*atxdmac;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/bestcomm/ata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/bestcomm/ata.c
@@ -133,7 +133,7 @@
 	struct bcom_ata_var *var;
 
 	/* Reset all BD */
-	memset(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
+	memset_io(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
 
 	tsk->index = 0;
 	tsk->outdex = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/bestcomm/bestcomm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/bestcomm/bestcomm.c
@@ -95,7 +95,7 @@
 		tsk->bd = bcom_sram_alloc(bd_count * bd_size, 4, &tsk->bd_pa);
 		if (!tsk->bd)
 			goto error;
-		memset(tsk->bd, 0x00, bd_count * bd_size);
+		memset_io(tsk->bd, 0x00, bd_count * bd_size);
 
 		tsk->num_bd = bd_count;
 		tsk->bd_size = bd_size;
@@ -186,16 +186,16 @@
 	inc = bcom_task_inc(task);
 
 	/* Clear & copy */
-	memset(var, 0x00, BCOM_VAR_SIZE);
-	memset(inc, 0x00, BCOM_INC_SIZE);
+	memset_io(var, 0x00, BCOM_VAR_SIZE);
+	memset_io(inc, 0x00, BCOM_INC_SIZE);
 
 	desc_src = (u32 *)(hdr + 1);
 	var_src = desc_src + hdr->desc_size;
 	inc_src = var_src + hdr->var_size;
 
-	memcpy(desc, desc_src, hdr->desc_size * sizeof(u32));
-	memcpy(var + hdr->first_var, var_src, hdr->var_size * sizeof(u32));
-	memcpy(inc, inc_src, hdr->inc_size * sizeof(u32));
+	memcpy_toio(desc, desc_src, hdr->desc_size * sizeof(u32));
+	memcpy_toio(var + hdr->first_var, var_src, hdr->var_size * sizeof(u32));
+	memcpy_toio(inc, inc_src, hdr->inc_size * sizeof(u32));
 
 	return 0;
 }
@@ -302,13 +302,13 @@
 		return -ENOMEM;
 	}
 
-	memset(bcom_eng->tdt, 0x00, tdt_size);
-	memset(bcom_eng->ctx, 0x00, ctx_size);
-	memset(bcom_eng->var, 0x00, var_size);
-	memset(bcom_eng->fdt, 0x00, fdt_size);
+	memset_io(bcom_eng->tdt, 0x00, tdt_size);
+	memset_io(bcom_eng->ctx, 0x00, ctx_size);
+	memset_io(bcom_eng->var, 0x00, var_size);
+	memset_io(bcom_eng->fdt, 0x00, fdt_size);
 
 	/* Copy the FDT for the EU#3 */
-	memcpy(&bcom_eng->fdt[48], fdt_ops, sizeof(fdt_ops));
+	memcpy_toio(&bcom_eng->fdt[48], fdt_ops, sizeof(fdt_ops));
 
 	/* Initialize Task base structure */
 	for (task=0; task<BCOM_MAX_TASKS; task++)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/bestcomm/fec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/bestcomm/fec.c
@@ -140,7 +140,7 @@
 	tsk->index = 0;
 	tsk->outdex = 0;
 
-	memset(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
+	memset_io(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
 
 	/* Configure some stuff */
 	bcom_set_task_pragma(tsk->tasknum, BCOM_FEC_RX_BD_PRAGMA);
@@ -241,7 +241,7 @@
 	tsk->index = 0;
 	tsk->outdex = 0;
 
-	memset(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
+	memset_io(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
 
 	/* Configure some stuff */
 	bcom_set_task_pragma(tsk->tasknum, BCOM_FEC_TX_BD_PRAGMA);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/bestcomm/gen_bd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/bestcomm/gen_bd.c
@@ -142,7 +142,7 @@
 	tsk->index = 0;
 	tsk->outdex = 0;
 
-	memset(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
+	memset_io(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
 
 	/* Configure some stuff */
 	bcom_set_task_pragma(tsk->tasknum, BCOM_GEN_RX_BD_PRAGMA);
@@ -226,7 +226,7 @@
 	tsk->index = 0;
 	tsk->outdex = 0;
 
-	memset(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
+	memset_io(tsk->bd, 0x00, tsk->num_bd * tsk->bd_size);
 
 	/* Configure some stuff */
 	bcom_set_task_pragma(tsk->tasknum, BCOM_GEN_TX_BD_PRAGMA);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dma-axi-dmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dma-axi-dmac.c
@@ -1020,8 +1020,8 @@
 {
 	struct axi_dmac *dmac = platform_get_drvdata(pdev);
 
-	of_dma_controller_free(pdev->dev.of_node);
 	free_irq(dmac->irq, dmac);
+	of_dma_controller_free(pdev->dev.of_node);
 	tasklet_kill(&dmac->chan.vchan.task);
 	dma_async_device_unregister(&dmac->dma_dev);
 	clk_disable_unprepare(dmac->clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dmaengine.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dmaengine.c
@@ -451,7 +451,8 @@
 	/* The channel is already in use, update client count */
 	if (chan->client_count) {
 		__module_get(owner);
-		goto out;
+		chan->client_count++;
+		return 0;
 	}
 
 	if (!try_module_get(owner))
@@ -470,11 +471,11 @@
 			goto err_out;
 	}
 
+	chan->client_count++;
+
 	if (!dma_has_cap(DMA_PRIVATE, chan->device->cap_mask))
 		balance_ref_count(chan);
 
-out:
-	chan->client_count++;
 	return 0;
 
 err_out:
@@ -1107,6 +1108,9 @@
 static void __dma_async_device_channel_unregister(struct dma_device *device,
 						  struct dma_chan *chan)
 {
+	if (chan->local == NULL)
+		return;
+
 	WARN_ONCE(!device->device_release && chan->client_count,
 		  "%s called while %d clients hold a reference\n",
 		  __func__, chan->client_count);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dmaengine.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dmaengine.h
@@ -176,7 +176,7 @@
 static inline bool
 dmaengine_desc_callback_valid(struct dmaengine_desc_callback *cb)
 {
-	return (cb->callback) ? true : false;
+	return cb->callback || cb->callback_result;
 }
 
 struct dma_chan *dma_get_slave_channel(struct dma_chan *chan);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c
@@ -213,6 +213,7 @@
 		kfree(desc);
 		return NULL;
 	}
+	desc->nr_hw_descs = num;
 
 	return desc;
 }
@@ -239,7 +240,7 @@
 static void axi_desc_put(struct axi_dma_desc *desc)
 {
 	struct axi_dma_chan *chan = desc->chan;
-	int count = atomic_read(&chan->descs_allocated);
+	int count = desc->nr_hw_descs;
 	struct axi_dma_hw_desc *hw_desc;
 	int descs_put;
 
@@ -288,8 +289,6 @@
 		len = vd_to_axi_desc(vdesc)->hw_desc[0].len;
 		completed_length = completed_blocks * len;
 		bytes = length - completed_length;
-	} else {
-		bytes = vd_to_axi_desc(vdesc)->length;
 	}
 
 	spin_unlock_irqrestore(&chan->vc.lock, flags);
@@ -944,6 +943,11 @@
 static void axi_chan_dump_lli(struct axi_dma_chan *chan,
 			      struct axi_dma_hw_desc *desc)
 {
+	if (!desc->lli) {
+		dev_err(dchan2dev(&chan->vc.chan), "NULL LLI\n");
+		return;
+	}
+
 	dev_err(dchan2dev(&chan->vc.chan),
 		"SAR: 0x%llx DAR: 0x%llx LLP: 0x%llx BTS 0x%x CTL: 0x%x:%08x",
 		le64_to_cpu(desc->lli->sar),
@@ -975,6 +979,11 @@
 
 	/* The bad descriptor currently is in the head of vc list */
 	vd = vchan_next_desc(&chan->vc);
+	if (!vd) {
+		dev_err(chan2dev(chan), "BUG: %s, IRQ with no descriptors\n",
+			axi_chan_name(chan));
+		goto out;
+	}
 	/* Remove the completed descriptor from issued list */
 	list_del(&vd->node);
 
@@ -989,6 +998,7 @@
 	/* Try to restart the controller */
 	axi_chan_start_first_queued(chan);
 
+out:
 	spin_unlock_irqrestore(&chan->vc.lock, flags);
 }
 
@@ -1011,6 +1021,11 @@
 
 	/* The completed descriptor currently is in the head of vc list */
 	vd = vchan_next_desc(&chan->vc);
+	if (!vd) {
+		dev_err(chan2dev(chan), "BUG: %s, IRQ with no descriptors\n",
+			axi_chan_name(chan));
+		goto out;
+	}
 
 	if (chan->cyclic) {
 		desc = vd_to_axi_desc(vd);
@@ -1035,11 +1050,9 @@
 		/* Remove the completed descriptor from issued list before completing */
 		list_del(&vd->node);
 		vchan_cookie_complete(vd);
-
-		/* Submit queued descriptors after processing the completed ones */
-		axi_chan_start_first_queued(chan);
 	}
 
+out:
 	spin_unlock_irqrestore(&chan->vc.lock, flags);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw-axi-dmac/dw-axi-dmac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw-axi-dmac/dw-axi-dmac.h
@@ -101,6 +101,7 @@
 	u32				completed_blocks;
 	u32				length;
 	u32				period_len;
+	u32				nr_hw_descs;
 };
 
 static inline struct device *dchan2dev(struct dma_chan *dchan)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw-edma/dw-edma-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw-edma/dw-edma-core.c
@@ -171,7 +171,7 @@
 	dw_edma_free_desc(vd2dw_edma_desc(vdesc));
 }
 
-static void dw_edma_start_transfer(struct dw_edma_chan *chan)
+static int dw_edma_start_transfer(struct dw_edma_chan *chan)
 {
 	struct dw_edma_chunk *child;
 	struct dw_edma_desc *desc;
@@ -179,16 +179,16 @@
 
 	vd = vchan_next_desc(&chan->vc);
 	if (!vd)
-		return;
+		return 0;
 
 	desc = vd2dw_edma_desc(vd);
 	if (!desc)
-		return;
+		return 0;
 
 	child = list_first_entry_or_null(&desc->chunk->list,
 					 struct dw_edma_chunk, list);
 	if (!child)
-		return;
+		return 0;
 
 	dw_edma_v0_core_start(child, !desc->xfer_sz);
 	desc->xfer_sz += child->ll_region.sz;
@@ -196,6 +196,8 @@
 	list_del(&child->list);
 	kfree(child);
 	desc->chunks_alloc--;
+
+	return 1;
 }
 
 static int dw_edma_device_config(struct dma_chan *dchan,
@@ -279,9 +281,12 @@
 	struct dw_edma_chan *chan = dchan2dw_edma_chan(dchan);
 	unsigned long flags;
 
+	if (!chan->configured)
+		return;
+
 	spin_lock_irqsave(&chan->vc.lock, flags);
-	if (chan->configured && chan->request == EDMA_REQ_NONE &&
-	    chan->status == EDMA_ST_IDLE && vchan_issue_pending(&chan->vc)) {
+	if (vchan_issue_pending(&chan->vc) && chan->request == EDMA_REQ_NONE &&
+	    chan->status == EDMA_ST_IDLE) {
 		chan->status = EDMA_ST_BUSY;
 		dw_edma_start_transfer(chan);
 	}
@@ -424,7 +429,7 @@
 		chunk->ll_region.sz += burst->sz;
 		desc->alloc_sz += burst->sz;
 
-		if (chan->dir == EDMA_DIR_WRITE) {
+		if (dir == DMA_DEV_TO_MEM) {
 			burst->sar = src_addr;
 			if (xfer->type == EDMA_XFER_CYCLIC) {
 				burst->dar = xfer->xfer.cyclic.paddr;
@@ -438,6 +443,8 @@
 				 * and destination addresses are increased
 				 * by the same portion (data length)
 				 */
+			} else if (xfer->type == EDMA_XFER_INTERLEAVED) {
+				burst->dar = dst_addr;
 			}
 		} else {
 			burst->dar = dst_addr;
@@ -453,6 +460,8 @@
 				 * and destination addresses are increased
 				 * by the same portion (data length)
 				 */
+			}  else if (xfer->type == EDMA_XFER_INTERLEAVED) {
+				burst->sar = src_addr;
 			}
 		}
 
@@ -551,14 +560,14 @@
 		switch (chan->request) {
 		case EDMA_REQ_NONE:
 			desc = vd2dw_edma_desc(vd);
-			if (desc->chunks_alloc) {
-				chan->status = EDMA_ST_BUSY;
-				dw_edma_start_transfer(chan);
-			} else {
+			if (!desc->chunks_alloc) {
 				list_del(&vd->node);
 				vchan_cookie_complete(vd);
-				chan->status = EDMA_ST_IDLE;
 			}
+
+			/* Continue transferring if there are remaining chunks or issued requests.
+			 */
+			chan->status = dw_edma_start_transfer(chan) ? EDMA_ST_BUSY : EDMA_ST_IDLE;
 			break;
 
 		case EDMA_REQ_STOP:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw-edma/dw-edma-v0-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw-edma/dw-edma-v0-core.c
@@ -192,7 +192,7 @@
 static inline u64 readq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			   const void __iomem *addr)
 {
-	u32 value;
+	u64 value;
 
 	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
@@ -415,8 +415,11 @@
 			  (DW_EDMA_V0_CCS | DW_EDMA_V0_LLE));
 		/* Linked list */
 		#ifdef CONFIG_64BIT
-			SET_CH_64(dw, chan->dir, chan->id, llp.reg,
-				  chunk->ll_region.paddr);
+			/* llp is not aligned on 64bit -> keep 32bit accesses */
+			SET_CH_32(dw, chan->dir, chan->id, llp.lsb,
+				  lower_32_bits(chunk->ll_region.paddr));
+			SET_CH_32(dw, chan->dir, chan->id, llp.msb,
+				  upper_32_bits(chunk->ll_region.paddr));
 		#else /* CONFIG_64BIT */
 			SET_CH_32(dw, chan->dir, chan->id, llp.lsb,
 				  lower_32_bits(chunk->ll_region.paddr));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw/acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw/acpi.c
@@ -8,13 +8,15 @@
 
 static bool dw_dma_acpi_filter(struct dma_chan *chan, void *param)
 {
+	struct dw_dma *dw = to_dw_dma(chan->device);
+	struct dw_dma_chip_pdata *data = dev_get_drvdata(dw->dma.dev);
 	struct acpi_dma_spec *dma_spec = param;
 	struct dw_dma_slave slave = {
 		.dma_dev = dma_spec->dev,
 		.src_id = dma_spec->slave_id,
 		.dst_id = dma_spec->slave_id,
-		.m_master = 0,
-		.p_master = 1,
+		.m_master = data->m_master,
+		.p_master = data->p_master,
 	};
 
 	return dw_dma_filter(chan, &slave);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw/core.c
@@ -16,6 +16,7 @@
 #include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/log2.h>
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/slab.h>
@@ -624,12 +625,10 @@
 	struct dw_desc		*prev;
 	struct dw_desc		*first;
 	u32			ctllo, ctlhi;
-	u8			m_master = dwc->dws.m_master;
-	u8			lms = DWC_LLP_LMS(m_master);
+	u8			lms = DWC_LLP_LMS(dwc->dws.m_master);
 	dma_addr_t		reg;
 	unsigned int		reg_width;
 	unsigned int		mem_width;
-	unsigned int		data_width = dw->pdata->data_width[m_master];
 	unsigned int		i;
 	struct scatterlist	*sg;
 	size_t			total_len = 0;
@@ -663,7 +662,7 @@
 			mem = sg_dma_address(sg);
 			len = sg_dma_len(sg);
 
-			mem_width = __ffs(data_width | mem | len);
+			mem_width = __ffs(sconfig->src_addr_width | mem | len);
 
 slave_sg_todev_fill_desc:
 			desc = dwc_desc_get(dwc);
@@ -723,7 +722,7 @@
 			lli_write(desc, sar, reg);
 			lli_write(desc, dar, mem);
 			lli_write(desc, ctlhi, ctlhi);
-			mem_width = __ffs(data_width | mem);
+			mem_width = __ffs(sconfig->dst_addr_width | mem);
 			lli_write(desc, ctllo, ctllo | DWC_CTLL_DST_WIDTH(mem_width));
 			desc->len = dlen;
 
@@ -783,17 +782,93 @@
 }
 EXPORT_SYMBOL_GPL(dw_dma_filter);
 
+static int dwc_verify_p_buswidth(struct dma_chan *chan)
+{
+	struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
+	struct dw_dma *dw = to_dw_dma(chan->device);
+	u32 reg_width, max_width;
+
+	if (dwc->dma_sconfig.direction == DMA_MEM_TO_DEV)
+		reg_width = dwc->dma_sconfig.dst_addr_width;
+	else if (dwc->dma_sconfig.direction == DMA_DEV_TO_MEM)
+		reg_width = dwc->dma_sconfig.src_addr_width;
+	else /* DMA_MEM_TO_MEM */
+		return 0;
+
+	max_width = dw->pdata->data_width[dwc->dws.p_master];
+
+	/* Fall-back to 1-byte transfer width if undefined */
+	if (reg_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
+		reg_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	else if (!is_power_of_2(reg_width) || reg_width > max_width)
+		return -EINVAL;
+	else /* bus width is valid */
+		return 0;
+
+	/* Update undefined addr width value */
+	if (dwc->dma_sconfig.direction == DMA_MEM_TO_DEV)
+		dwc->dma_sconfig.dst_addr_width = reg_width;
+	else /* DMA_DEV_TO_MEM */
+		dwc->dma_sconfig.src_addr_width = reg_width;
+
+	return 0;
+}
+
+static int dwc_verify_m_buswidth(struct dma_chan *chan)
+{
+	struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
+	struct dw_dma *dw = to_dw_dma(chan->device);
+	u32 reg_width, reg_burst, mem_width;
+
+	mem_width = dw->pdata->data_width[dwc->dws.m_master];
+
+	/*
+	 * It's possible to have a data portion locked in the DMA FIFO in case
+	 * of the channel suspension. Subsequent channel disabling will cause
+	 * that data silent loss. In order to prevent that maintain the src and
+	 * dst transfer widths coherency by means of the relation:
+	 * (CTLx.SRC_TR_WIDTH * CTLx.SRC_MSIZE >= CTLx.DST_TR_WIDTH)
+	 * Look for the details in the commit message that brings this change.
+	 *
+	 * Note the DMA configs utilized in the calculations below must have
+	 * been verified to have correct values by this method call.
+	 */
+	if (dwc->dma_sconfig.direction == DMA_MEM_TO_DEV) {
+		reg_width = dwc->dma_sconfig.dst_addr_width;
+		if (mem_width < reg_width)
+			return -EINVAL;
+
+		dwc->dma_sconfig.src_addr_width = mem_width;
+	} else if (dwc->dma_sconfig.direction == DMA_DEV_TO_MEM) {
+		reg_width = dwc->dma_sconfig.src_addr_width;
+		reg_burst = rounddown_pow_of_two(dwc->dma_sconfig.src_maxburst);
+
+		dwc->dma_sconfig.dst_addr_width = min(mem_width, reg_width * reg_burst);
+	}
+
+	return 0;
+}
+
 static int dwc_config(struct dma_chan *chan, struct dma_slave_config *sconfig)
 {
 	struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
 	struct dw_dma *dw = to_dw_dma(chan->device);
+	int ret;
 
 	memcpy(&dwc->dma_sconfig, sconfig, sizeof(*sconfig));
 
 	dwc->dma_sconfig.src_maxburst =
-		clamp(dwc->dma_sconfig.src_maxburst, 0U, dwc->max_burst);
+		clamp(dwc->dma_sconfig.src_maxburst, 1U, dwc->max_burst);
 	dwc->dma_sconfig.dst_maxburst =
-		clamp(dwc->dma_sconfig.dst_maxburst, 0U, dwc->max_burst);
+		clamp(dwc->dma_sconfig.dst_maxburst, 1U, dwc->max_burst);
+
+	ret = dwc_verify_p_buswidth(chan);
+	if (ret)
+		return ret;
+
+	ret = dwc_verify_m_buswidth(chan);
+	if (ret)
+		return ret;
 
 	dw->encode_maxburst(dwc, &dwc->dma_sconfig.src_maxburst);
 	dw->encode_maxburst(dwc, &dwc->dma_sconfig.dst_maxburst);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw/internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw/internal.h
@@ -51,11 +51,15 @@
 	int (*probe)(struct dw_dma_chip *chip);
 	int (*remove)(struct dw_dma_chip *chip);
 	struct dw_dma_chip *chip;
+	u8 m_master;
+	u8 p_master;
 };
 
 static __maybe_unused const struct dw_dma_chip_pdata dw_dma_chip_pdata = {
 	.probe = dw_dma_probe,
 	.remove = dw_dma_remove,
+	.m_master = 0,
+	.p_master = 1,
 };
 
 static const struct dw_dma_platform_data idma32_pdata = {
@@ -72,6 +76,8 @@
 	.pdata = &idma32_pdata,
 	.probe = idma32_dma_probe,
 	.remove = idma32_dma_remove,
+	.m_master = 0,
+	.p_master = 0,
 };
 
 static const struct dw_dma_platform_data xbar_pdata = {
@@ -88,6 +94,8 @@
 	.pdata = &xbar_pdata,
 	.probe = idma32_dma_probe,
 	.remove = idma32_dma_remove,
+	.m_master = 0,
+	.p_master = 0,
 };
 
 #endif /* _DMA_DW_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/dw/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/dw/pci.c
@@ -60,10 +60,10 @@
 	if (ret)
 		return ret;
 
-	dw_dma_acpi_controller_register(chip->dw);
-
 	pci_set_drvdata(pdev, data);
 
+	dw_dma_acpi_controller_register(chip->dw);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/fsl-dpaa2-qdma/dpaa2-qdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/fsl-dpaa2-qdma/dpaa2-qdma.c
@@ -38,15 +38,17 @@
 	if (!dpaa2_chan->fd_pool)
 		goto err;
 
-	dpaa2_chan->fl_pool = dma_pool_create("fl_pool", dev,
-					      sizeof(struct dpaa2_fl_entry),
-					      sizeof(struct dpaa2_fl_entry), 0);
+	dpaa2_chan->fl_pool =
+		dma_pool_create("fl_pool", dev,
+				 sizeof(struct dpaa2_fl_entry) * 3,
+				 sizeof(struct dpaa2_fl_entry), 0);
+
 	if (!dpaa2_chan->fl_pool)
 		goto err_fd;
 
 	dpaa2_chan->sdd_pool =
 		dma_pool_create("sdd_pool", dev,
-				sizeof(struct dpaa2_qdma_sd_d),
+				sizeof(struct dpaa2_qdma_sd_d) * 2,
 				sizeof(struct dpaa2_qdma_sd_d), 0);
 	if (!dpaa2_chan->sdd_pool)
 		goto err_fl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/fsl-qdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/fsl-qdma.c
@@ -109,6 +109,7 @@
 #define FSL_QDMA_CMD_WTHROTL_OFFSET	20
 #define FSL_QDMA_CMD_DSEN_OFFSET	19
 #define FSL_QDMA_CMD_LWC_OFFSET		16
+#define FSL_QDMA_CMD_PF			BIT(17)
 
 /* Field definition for Descriptor status */
 #define QDMA_CCDF_STATUS_RTE		BIT(5)
@@ -384,7 +385,8 @@
 	qdma_csgf_set_f(csgf_dest, len);
 	/* Descriptor Buffer */
 	cmd = cpu_to_le32(FSL_QDMA_CMD_RWTTYPE <<
-			  FSL_QDMA_CMD_RWTTYPE_OFFSET);
+			  FSL_QDMA_CMD_RWTTYPE_OFFSET) |
+			  FSL_QDMA_CMD_PF;
 	sdf->data = QDMA_SDDF_CMD(cmd);
 
 	cmd = cpu_to_le32(FSL_QDMA_CMD_RWTTYPE <<
@@ -514,11 +516,11 @@
 			queue_temp = queue_head + i + (j * queue_num);
 
 			queue_temp->cq =
-			dma_alloc_coherent(&pdev->dev,
-					   sizeof(struct fsl_qdma_format) *
-					   queue_size[i],
-					   &queue_temp->bus_addr,
-					   GFP_KERNEL);
+			dmam_alloc_coherent(&pdev->dev,
+					    sizeof(struct fsl_qdma_format) *
+					    queue_size[i],
+					    &queue_temp->bus_addr,
+					    GFP_KERNEL);
 			if (!queue_temp->cq)
 				return NULL;
 			queue_temp->block_base = fsl_qdma->block_base +
@@ -563,11 +565,11 @@
 	/*
 	 * Buffer for queue command
 	 */
-	status_head->cq = dma_alloc_coherent(&pdev->dev,
-					     sizeof(struct fsl_qdma_format) *
-					     status_size,
-					     &status_head->bus_addr,
-					     GFP_KERNEL);
+	status_head->cq = dmam_alloc_coherent(&pdev->dev,
+					      sizeof(struct fsl_qdma_format) *
+					      status_size,
+					      &status_head->bus_addr,
+					      GFP_KERNEL);
 	if (!status_head->cq) {
 		devm_kfree(&pdev->dev, status_head);
 		return NULL;
@@ -805,7 +807,7 @@
 	int i;
 	int cpu;
 	int ret;
-	char irq_name[20];
+	char irq_name[32];
 
 	fsl_qdma->error_irq =
 		platform_get_irq_byname(pdev, "qdma-error");
@@ -1201,10 +1203,6 @@
 	if (!fsl_qdma->queue)
 		return -ENOMEM;
 
-	ret = fsl_qdma_irq_init(pdev, fsl_qdma);
-	if (ret)
-		return ret;
-
 	fsl_qdma->irq_base = platform_get_irq_byname(pdev, "qdma-queue0");
 	if (fsl_qdma->irq_base < 0)
 		return fsl_qdma->irq_base;
@@ -1243,16 +1241,19 @@
 
 	platform_set_drvdata(pdev, fsl_qdma);
 
-	ret = dma_async_device_register(&fsl_qdma->dma_dev);
+	ret = fsl_qdma_reg_init(fsl_qdma);
 	if (ret) {
-		dev_err(&pdev->dev,
-			"Can't register NXP Layerscape qDMA engine.\n");
+		dev_err(&pdev->dev, "Can't Initialize the qDMA engine.\n");
 		return ret;
 	}
 
-	ret = fsl_qdma_reg_init(fsl_qdma);
+	ret = fsl_qdma_irq_init(pdev, fsl_qdma);
+	if (ret)
+		return ret;
+
+	ret = dma_async_device_register(&fsl_qdma->dma_dev);
 	if (ret) {
-		dev_err(&pdev->dev, "Can't Initialize the qDMA engine.\n");
+		dev_err(&pdev->dev, "Can't register NXP Layerscape qDMA engine.\n");
 		return ret;
 	}
 
@@ -1272,8 +1273,6 @@
 
 static int fsl_qdma_remove(struct platform_device *pdev)
 {
-	int i;
-	struct fsl_qdma_queue *status;
 	struct device_node *np = pdev->dev.of_node;
 	struct fsl_qdma_engine *fsl_qdma = platform_get_drvdata(pdev);
 
@@ -1282,11 +1281,6 @@
 	of_dma_controller_free(np);
 	dma_async_device_unregister(&fsl_qdma->dma_dev);
 
-	for (i = 0; i < fsl_qdma->block_number; i++) {
-		status = fsl_qdma->status[i];
-		dma_free_coherent(&pdev->dev, sizeof(struct fsl_qdma_format) *
-				status->n_cq, status->cq, status->bus_addr);
-	}
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/hisi_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/hisi_dma.c
@@ -30,7 +30,7 @@
 #define HISI_DMA_MODE			0x217c
 #define HISI_DMA_OFFSET			0x100
 
-#define HISI_DMA_MSI_NUM		30
+#define HISI_DMA_MSI_NUM		32
 #define HISI_DMA_CHAN_NUM		30
 #define HISI_DMA_Q_DEPTH_VAL		1024
 
@@ -180,7 +180,8 @@
 	hisi_dma_chan_write(hdma_dev->base, HISI_DMA_CQ_HEAD_PTR, index, 0);
 }
 
-static void hisi_dma_reset_hw_chan(struct hisi_dma_chan *chan)
+static void hisi_dma_reset_or_disable_hw_chan(struct hisi_dma_chan *chan,
+					      bool disable)
 {
 	struct hisi_dma_dev *hdma_dev = chan->hdma_dev;
 	u32 index = chan->qp_num, tmp;
@@ -201,8 +202,11 @@
 	hisi_dma_do_reset(hdma_dev, index);
 	hisi_dma_reset_qp_point(hdma_dev, index);
 	hisi_dma_pause_dma(hdma_dev, index, false);
-	hisi_dma_enable_dma(hdma_dev, index, true);
-	hisi_dma_unmask_irq(hdma_dev, index);
+
+	if (!disable) {
+		hisi_dma_enable_dma(hdma_dev, index, true);
+		hisi_dma_unmask_irq(hdma_dev, index);
+	}
 
 	ret = readl_relaxed_poll_timeout(hdma_dev->base +
 		HISI_DMA_Q_FSM_STS + index * HISI_DMA_OFFSET, tmp,
@@ -218,7 +222,7 @@
 	struct hisi_dma_chan *chan = to_hisi_dma_chan(c);
 	struct hisi_dma_dev *hdma_dev = chan->hdma_dev;
 
-	hisi_dma_reset_hw_chan(chan);
+	hisi_dma_reset_or_disable_hw_chan(chan, false);
 	vchan_free_chan_resources(&chan->vc);
 
 	memset(chan->sq, 0, sizeof(struct hisi_dma_sqe) * hdma_dev->chan_depth);
@@ -267,7 +271,6 @@
 
 	vd = vchan_next_desc(&chan->vc);
 	if (!vd) {
-		dev_err(&hdma_dev->pdev->dev, "no issued task!\n");
 		chan->desc = NULL;
 		return;
 	}
@@ -299,7 +302,7 @@
 
 	spin_lock_irqsave(&chan->vc.lock, flags);
 
-	if (vchan_issue_pending(&chan->vc))
+	if (vchan_issue_pending(&chan->vc) && !chan->desc)
 		hisi_dma_start_transfer(chan);
 
 	spin_unlock_irqrestore(&chan->vc.lock, flags);
@@ -394,7 +397,7 @@
 
 static void hisi_dma_disable_qp(struct hisi_dma_dev *hdma_dev, u32 qp_index)
 {
-	hisi_dma_reset_hw_chan(&hdma_dev->chan[qp_index]);
+	hisi_dma_reset_or_disable_hw_chan(&hdma_dev->chan[qp_index], true);
 }
 
 static void hisi_dma_enable_qps(struct hisi_dma_dev *hdma_dev)
@@ -432,18 +435,15 @@
 	desc = chan->desc;
 	cqe = chan->cq + chan->cq_head;
 	if (desc) {
+		chan->cq_head = (chan->cq_head + 1) % hdma_dev->chan_depth;
+		hisi_dma_chan_write(hdma_dev->base, HISI_DMA_CQ_HEAD_PTR,
+				    chan->qp_num, chan->cq_head);
 		if (FIELD_GET(STATUS_MASK, cqe->w0) == STATUS_SUCC) {
-			chan->cq_head = (chan->cq_head + 1) %
-					hdma_dev->chan_depth;
-			hisi_dma_chan_write(hdma_dev->base,
-					    HISI_DMA_CQ_HEAD_PTR, chan->qp_num,
-					    chan->cq_head);
 			vchan_cookie_complete(&desc->vd);
+			hisi_dma_start_transfer(chan);
 		} else {
 			dev_err(&hdma_dev->pdev->dev, "task error!\n");
 		}
-
-		chan->desc = NULL;
 	}
 
 	spin_unlock(&chan->vc.lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idma64.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idma64.c
@@ -167,6 +167,10 @@
 	u32 status_err;
 	unsigned short i;
 
+	/* Since IRQ may be shared, check if DMA controller is powered on */
+	if (status == GENMASK(31, 0))
+		return IRQ_NONE;
+
 	dev_vdbg(idma64->dma.dev, "%s: status=%#x\n", __func__, status);
 
 	/* Check if we have any interrupt from the DMA controller */
@@ -590,7 +594,9 @@
 
 	idma64->dma.dev = chip->sysdev;
 
-	dma_set_max_seg_size(idma64->dma.dev, IDMA64C_CTLH_BLOCK_TS_MASK);
+	ret = dma_set_max_seg_size(idma64->dma.dev, IDMA64C_CTLH_BLOCK_TS_MASK);
+	if (ret)
+		return ret;
 
 	ret = dma_async_device_register(&idma64->dma);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/Makefile
@@ -1,12 +1,12 @@
 ccflags-y += -DDEFAULT_SYMBOL_NAMESPACE=IDXD
 
+obj-$(CONFIG_INTEL_IDXD_BUS) += idxd_bus.o
+idxd_bus-y := bus.o
+
 obj-$(CONFIG_INTEL_IDXD) += idxd.o
 idxd-y := init.o irq.o device.o sysfs.o submit.o dma.o cdev.o
 
 idxd-$(CONFIG_INTEL_IDXD_PERFMON) += perfmon.o
 
-obj-$(CONFIG_INTEL_IDXD_BUS) += idxd_bus.o
-idxd_bus-y := bus.o
-
 obj-$(CONFIG_INTEL_IDXD_COMPAT) += idxd_compat.o
 idxd_compat-y := compat.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/cdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/cdev.c
@@ -198,6 +198,18 @@
 	int rc;
 
 	dev_dbg(&pdev->dev, "%s called\n", __func__);
+
+	/*
+	 * Due to an erratum in some of the devices supported by the driver,
+	 * direct user submission to the device can be unsafe.
+	 * (See document INTEL-SA-01084)
+	 *
+	 * For the devices that exhibit this behavior, require that the user
+	 * has CAP_SYS_RAWIO capabilities.
+	 */
+	if (!idxd->user_submission_safe && !capable(CAP_SYS_RAWIO))
+		return -EPERM;
+
 	rc = check_vma(wq, vma, __func__);
 	if (rc < 0)
 		return rc;
@@ -212,6 +224,72 @@
 			vma->vm_page_prot);
 }
 
+static int idxd_submit_user_descriptor(struct idxd_user_context *ctx,
+				       struct dsa_hw_desc __user *udesc)
+{
+	struct idxd_wq *wq = ctx->wq;
+	struct idxd_dev *idxd_dev = &wq->idxd->idxd_dev;
+	const uint64_t comp_addr_align = is_dsa_dev(idxd_dev) ? 0x20 : 0x40;
+	void __iomem *portal = idxd_wq_portal_addr(wq);
+	struct dsa_hw_desc descriptor __aligned(64);
+	int rc;
+	unsigned int retries;
+
+	rc = copy_from_user(&descriptor, udesc, sizeof(descriptor));
+	if (rc)
+		return -EFAULT;
+
+	/*
+	 * DSA devices are capable of indirect ("batch") command submission.
+	 * On devices where direct user submissions are not safe, we cannot
+	 * allow this since there is no good way for us to verify these
+	 * indirect commands.
+	 */
+	if (is_dsa_dev(idxd_dev) && descriptor.opcode == DSA_OPCODE_BATCH &&
+		!wq->idxd->user_submission_safe)
+		return -EINVAL;
+	/*
+	 * As per the programming specification, the completion address must be
+	 * aligned to 32 or 64 bytes. If this is violated the hardware
+	 * engine can get very confused (security issue).
+	 */
+	if (!IS_ALIGNED(descriptor.completion_addr, comp_addr_align))
+		return -EINVAL;
+
+	if (wq_dedicated(wq))
+		iosubmit_cmds512(portal, &descriptor, 1);
+	else {
+		descriptor.priv = 0;
+		descriptor.pasid = ctx->pasid;
+
+		rc = idxd_enqcmds(wq, portal, &descriptor);
+		if (rc < 0)
+			return rc;
+	}
+
+	return 0;
+}
+
+static ssize_t idxd_cdev_write(struct file *filp, const char __user *buf, size_t len,
+			       loff_t *unused)
+{
+	struct dsa_hw_desc __user *udesc = (struct dsa_hw_desc __user *)buf;
+	struct idxd_user_context *ctx = filp->private_data;
+	ssize_t written = 0;
+	int i;
+
+	for (i = 0; i < len/sizeof(struct dsa_hw_desc); i++) {
+		int rc = idxd_submit_user_descriptor(ctx, udesc + i);
+
+		if (rc)
+			return written ? written : rc;
+
+		written += sizeof(struct dsa_hw_desc);
+	}
+
+	return written;
+}
+
 static __poll_t idxd_cdev_poll(struct file *filp,
 			       struct poll_table_struct *wait)
 {
@@ -234,6 +312,7 @@
 	.open = idxd_cdev_open,
 	.release = idxd_cdev_release,
 	.mmap = idxd_cdev_mmap,
+	.write = idxd_cdev_write,
 	.poll = idxd_cdev_poll,
 };
 
@@ -369,10 +448,16 @@
 		rc = alloc_chrdev_region(&ictx[i].devt, 0, MINORMASK,
 					 ictx[i].name);
 		if (rc)
-			return rc;
+			goto err_free_chrdev_region;
 	}
 
 	return 0;
+
+err_free_chrdev_region:
+	for (i--; i >= 0; i--)
+		unregister_chrdev_region(ictx[i].devt, MINORMASK);
+
+	return rc;
 }
 
 void idxd_cdev_remove(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/device.c
@@ -394,14 +394,23 @@
 	lockdep_assert_held(&wq->wq_lock);
 	memset(wq->wqcfg, 0, idxd->wqcfg_size);
 	wq->type = IDXD_WQT_NONE;
-	wq->size = 0;
-	wq->group = NULL;
 	wq->threshold = 0;
 	wq->priority = 0;
 	wq->ats_dis = 0;
+	wq->enqcmds_retries = IDXD_ENQCMDS_RETRIES;
 	clear_bit(WQ_FLAG_DEDICATED, &wq->flags);
 	clear_bit(WQ_FLAG_BLOCK_ON_FAULT, &wq->flags);
 	memset(wq->name, 0, WQ_NAME_SIZE);
+	if (wq->opcap_bmap)
+		bitmap_copy(wq->opcap_bmap, idxd->opcap_bmap, IDXD_MAX_OPCAP_BITS);
+}
+
+static void idxd_wq_device_reset_cleanup(struct idxd_wq *wq)
+{
+	lockdep_assert_held(&wq->wq_lock);
+
+	wq->size = 0;
+	wq->group = NULL;
 }
 
 static void idxd_wq_ref_release(struct percpu_ref *ref)
@@ -427,7 +436,6 @@
 {
 	percpu_ref_kill(&wq->wq_active);
 	wait_for_completion(&wq->wq_dead);
-	percpu_ref_exit(&wq->wq_active);
 }
 
 /* Device control bits */
@@ -485,6 +493,7 @@
 	union idxd_command_reg cmd;
 	DECLARE_COMPLETION_ONSTACK(done);
 	u32 stat;
+	unsigned long flags;
 
 	if (idxd_device_is_halted(idxd)) {
 		dev_warn(&idxd->pdev->dev, "Device is HALTED!\n");
@@ -498,7 +507,7 @@
 	cmd.operand = operand;
 	cmd.int_req = 1;
 
-	spin_lock(&idxd->cmd_lock);
+	spin_lock_irqsave(&idxd->cmd_lock, flags);
 	wait_event_lock_irq(idxd->cmd_waitq,
 			    !test_bit(IDXD_FLAG_CMD_RUNNING, &idxd->flags),
 			    idxd->cmd_lock);
@@ -515,7 +524,7 @@
 	 * After command submitted, release lock and go to sleep until
 	 * the command completes via interrupt.
 	 */
-	spin_unlock(&idxd->cmd_lock);
+	spin_unlock_irqrestore(&idxd->cmd_lock, flags);
 	wait_for_completion(&done);
 	stat = ioread32(idxd->reg_base + IDXD_CMDSTS_OFFSET);
 	spin_lock(&idxd->cmd_lock);
@@ -584,6 +593,8 @@
 	spin_lock(&idxd->dev_lock);
 	idxd_device_clear_state(idxd);
 	idxd->state = IDXD_DEV_DISABLED;
+	idxd_unmask_error_interrupts(idxd);
+	idxd_msix_perm_setup(idxd);
 	spin_unlock(&idxd->dev_lock);
 }
 
@@ -692,11 +703,16 @@
 		memset(&group->grpcfg, 0, sizeof(group->grpcfg));
 		group->num_engines = 0;
 		group->num_wqs = 0;
-		group->use_token_limit = false;
-		group->tokens_allowed = 0;
-		group->tokens_reserved = 0;
-		group->tc_a = -1;
-		group->tc_b = -1;
+		group->use_rdbuf_limit = false;
+		group->rdbufs_allowed = 0;
+		group->rdbufs_reserved = 0;
+		if (idxd->hw.version <= DEVICE_VERSION_2 && !tc_override) {
+			group->tc_a = 1;
+			group->tc_b = 1;
+		} else {
+			group->tc_a = -1;
+			group->tc_b = -1;
+		}
 	}
 }
 
@@ -708,15 +724,16 @@
 	for (i = 0; i < idxd->max_wqs; i++) {
 		struct idxd_wq *wq = idxd->wqs[i];
 
-		if (wq->state == IDXD_WQ_ENABLED) {
-			idxd_wq_disable_cleanup(wq);
-			wq->state = IDXD_WQ_DISABLED;
-		}
+		idxd_wq_disable_cleanup(wq);
+		idxd_wq_device_reset_cleanup(wq);
 	}
 }
 
 void idxd_device_clear_state(struct idxd_device *idxd)
 {
+	if (!test_bit(IDXD_FLAG_CONFIGURABLE, &idxd->flags))
+		return;
+
 	idxd_groups_clear_state(idxd);
 	idxd_engines_clear_state(idxd);
 	idxd_device_wqs_clear_state(idxd);
@@ -791,10 +808,10 @@
 	int i;
 	struct device *dev = &idxd->pdev->dev;
 
-	/* Setup bandwidth token limit */
-	if (idxd->token_limit) {
+	/* Setup bandwidth rdbuf limit */
+	if (idxd->hw.gen_cap.config_en && idxd->rdbuf_limit) {
 		reg.bits = ioread32(idxd->reg_base + IDXD_GENCFG_OFFSET);
-		reg.token_limit = idxd->token_limit;
+		reg.rdbuf_limit = idxd->rdbuf_limit;
 		iowrite32(reg.bits, idxd->reg_base + IDXD_GENCFG_OFFSET);
 	}
 
@@ -824,7 +841,7 @@
 	struct idxd_device *idxd = wq->idxd;
 	struct device *dev = &idxd->pdev->dev;
 	u32 wq_offset;
-	int i;
+	int i, n;
 
 	if (!wq->group)
 		return 0;
@@ -892,6 +909,17 @@
 	wq->wqcfg->max_xfer_shift = ilog2(wq->max_xfer_bytes);
 	wq->wqcfg->max_batch_shift = ilog2(wq->max_batch_size);
 
+	/* bytes 32-63 */
+	if (idxd->hw.wq_cap.op_config && wq->opcap_bmap) {
+		memset(wq->wqcfg->op_config, 0, IDXD_MAX_OPCAP_BITS / 8);
+		for_each_set_bit(n, wq->opcap_bmap, IDXD_MAX_OPCAP_BITS) {
+			int pos = n % BITS_PER_LONG_LONG;
+			int idx = n / BITS_PER_LONG_LONG;
+
+			wq->wqcfg->op_config[idx] |= BIT(pos);
+		}
+	}
+
 	dev_dbg(dev, "WQ %d CFGs\n", wq->id);
 	for (i = 0; i < WQCFG_STRIDES(idxd); i++) {
 		wq_offset = WQCFG_OFFSET(idxd, wq->id, i);
@@ -935,13 +963,12 @@
 			group->tc_b = group->grpcfg.flags.tc_b = 1;
 		else
 			group->grpcfg.flags.tc_b = group->tc_b;
-		group->grpcfg.flags.use_token_limit = group->use_token_limit;
-		group->grpcfg.flags.tokens_reserved = group->tokens_reserved;
-		if (group->tokens_allowed)
-			group->grpcfg.flags.tokens_allowed =
-				group->tokens_allowed;
+		group->grpcfg.flags.use_rdbuf_limit = group->use_rdbuf_limit;
+		group->grpcfg.flags.rdbufs_reserved = group->rdbufs_reserved;
+		if (group->rdbufs_allowed)
+			group->grpcfg.flags.rdbufs_allowed = group->rdbufs_allowed;
 		else
-			group->grpcfg.flags.tokens_allowed = idxd->max_tokens;
+			group->grpcfg.flags.rdbufs_allowed = idxd->max_rdbufs;
 	}
 }
 
@@ -1136,7 +1163,7 @@
 	int i, rc;
 
 	reg.bits = ioread32(idxd->reg_base + IDXD_GENCFG_OFFSET);
-	idxd->token_limit = reg.token_limit;
+	idxd->rdbuf_limit = reg.rdbuf_limit;
 
 	for (i = 0; i < idxd->max_groups; i++) {
 		struct idxd_group *group = idxd->groups[i];
@@ -1236,8 +1263,7 @@
 	return 0;
 
 err_map_portal:
-	rc = idxd_wq_disable(wq, false);
-	if (rc < 0)
+	if (idxd_wq_disable(wq, false))
 		dev_dbg(dev, "wq %s disable failed\n", dev_name(wq_confdev(wq)));
 err:
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/dma.c
@@ -78,6 +78,27 @@
 }
 
 static struct dma_async_tx_descriptor *
+idxd_dma_prep_interrupt(struct dma_chan *c, unsigned long flags)
+{
+	struct idxd_wq *wq = to_idxd_wq(c);
+	u32 desc_flags;
+	struct idxd_desc *desc;
+
+	if (wq->state != IDXD_WQ_ENABLED)
+		return NULL;
+
+	op_flag_setup(flags, &desc_flags);
+	desc = idxd_alloc_desc(wq, IDXD_OP_BLOCK);
+	if (IS_ERR(desc))
+		return NULL;
+
+	idxd_prep_desc_common(wq, desc->hw, DSA_OPCODE_NOOP,
+			      0, 0, 0, desc->compl_dma, desc_flags);
+	desc->txd.flags = flags;
+	return &desc->txd;
+}
+
+static struct dma_async_tx_descriptor *
 idxd_dma_submit_memcpy(struct dma_chan *c, dma_addr_t dma_dest,
 		       dma_addr_t dma_src, size_t len, unsigned long flags)
 {
@@ -181,10 +202,12 @@
 	INIT_LIST_HEAD(&dma->channels);
 	dma->dev = dev;
 
+	dma_cap_set(DMA_INTERRUPT, dma->cap_mask);
 	dma_cap_set(DMA_PRIVATE, dma->cap_mask);
 	dma_cap_set(DMA_COMPLETION_NO_ORDER, dma->cap_mask);
 	dma->device_release = idxd_dma_release;
 
+	dma->device_prep_dma_interrupt = idxd_dma_prep_interrupt;
 	if (idxd->hw.opcap.bits[0] & IDXD_OPCAP_MEMMOVE) {
 		dma_cap_set(DMA_MEMCPY, dma->cap_mask);
 		dma->device_prep_dma_memcpy = idxd_dma_submit_memcpy;
@@ -311,6 +334,7 @@
 
 err_dma:
 	idxd_wq_quiesce(wq);
+	percpu_ref_exit(&wq->wq_active);
 err_ref:
 	idxd_wq_free_resources(wq);
 err_res_alloc:
@@ -328,9 +352,9 @@
 	mutex_lock(&wq->wq_lock);
 	idxd_wq_quiesce(wq);
 	idxd_unregister_dma_channel(wq);
-	__drv_disable_wq(wq);
 	idxd_wq_free_resources(wq);
-	wq->type = IDXD_WQT_NONE;
+	__drv_disable_wq(wq);
+	percpu_ref_exit(&wq->wq_active);
 	mutex_unlock(&wq->wq_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/idxd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/idxd.h
@@ -10,6 +10,7 @@
 #include <linux/cdev.h>
 #include <linux/idr.h>
 #include <linux/pci.h>
+#include <linux/bitmap.h>
 #include <linux/perf_event.h>
 #include <uapi/linux/idxd.h>
 #include "registers.h"
@@ -51,6 +52,9 @@
 #define IDXD_NAME_SIZE		128
 #define IDXD_PMU_EVENT_MAX	64
 
+#define IDXD_ENQCMDS_RETRIES		32
+#define IDXD_ENQCMDS_MAX_RETRIES	64
+
 struct idxd_device_driver {
 	const char *name;
 	enum idxd_dev_type *type;
@@ -84,9 +88,9 @@
 	int id;
 	int num_engines;
 	int num_wqs;
-	bool use_token_limit;
-	u8 tokens_allowed;
-	u8 tokens_reserved;
+	bool use_rdbuf_limit;
+	u8 rdbufs_allowed;
+	u8 rdbufs_reserved;
 	int tc_a;
 	int tc_b;
 };
@@ -164,6 +168,7 @@
 struct idxd_wq {
 	void __iomem *portal;
 	u32 portal_offset;
+	unsigned int enqcmds_retries;
 	struct percpu_ref wq_active;
 	struct completion wq_dead;
 	struct idxd_dev idxd_dev;
@@ -181,6 +186,8 @@
 	enum idxd_wq_state state;
 	unsigned long flags;
 	union wqcfg *wqcfg;
+	unsigned long *opcap_bmap;
+
 	struct dsa_hw_desc **hw_descs;
 	int num_descs;
 	union {
@@ -241,6 +248,7 @@
 	struct device_type *dev_type;
 	int compl_size;
 	int align;
+	bool user_submission_safe;
 };
 
 struct idxd_device {
@@ -278,11 +286,11 @@
 	u32 max_batch_size;
 	int max_groups;
 	int max_engines;
-	int max_tokens;
+	int max_rdbufs;
 	int max_wqs;
 	int max_wq_size;
-	int token_limit;
-	int nr_tokens;		/* non-reserved tokens */
+	int rdbuf_limit;
+	int nr_rdbufs;		/* non-reserved read buffers */
 	unsigned int wqcfg_size;
 
 	union sw_err_reg sw_err;
@@ -297,6 +305,10 @@
 	int *int_handles;
 
 	struct idxd_pmu *idxd_pmu;
+
+	unsigned long *opcap_bmap;
+
+	bool user_submission_safe;
 };
 
 /* IDXD software descriptor */
@@ -573,6 +585,7 @@
 int idxd_submit_desc(struct idxd_wq *wq, struct idxd_desc *desc);
 struct idxd_desc *idxd_alloc_desc(struct idxd_wq *wq, enum idxd_op_type optype);
 void idxd_free_desc(struct idxd_wq *wq, struct idxd_desc *desc);
+int idxd_enqcmds(struct idxd_wq *wq, void __iomem *portal, const void *desc);
 
 /* dmaengine */
 int idxd_register_dma_device(struct idxd_device *idxd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/init.c
@@ -48,6 +48,7 @@
 		.compl_size = sizeof(struct dsa_completion_record),
 		.align = 32,
 		.dev_type = &dsa_device_type,
+		.user_submission_safe = false, /* See INTEL-SA-01084 erratum */
 	},
 	[IDXD_TYPE_IAX] = {
 		.name_prefix = "iax",
@@ -55,6 +56,7 @@
 		.compl_size = sizeof(struct iax_completion_record),
 		.align = 64,
 		.dev_type = &iax_device_type,
+		.user_submission_safe = false, /* See INTEL-SA-01084 erratum */
 	},
 };
 
@@ -239,12 +241,23 @@
 		init_completion(&wq->wq_dead);
 		wq->max_xfer_bytes = idxd->max_xfer_bytes;
 		wq->max_batch_size = idxd->max_batch_size;
+		wq->enqcmds_retries = IDXD_ENQCMDS_RETRIES;
 		wq->wqcfg = kzalloc_node(idxd->wqcfg_size, GFP_KERNEL, dev_to_node(dev));
 		if (!wq->wqcfg) {
 			put_device(conf_dev);
 			rc = -ENOMEM;
 			goto err;
 		}
+
+		if (idxd->hw.wq_cap.op_config) {
+			wq->opcap_bmap = bitmap_zalloc(IDXD_MAX_OPCAP_BITS, GFP_KERNEL);
+			if (!wq->opcap_bmap) {
+				put_device(conf_dev);
+				rc = -ENOMEM;
+				goto err;
+			}
+			bitmap_copy(wq->opcap_bmap, idxd->opcap_bmap, IDXD_MAX_OPCAP_BITS);
+		}
 		idxd->wqs[i] = wq;
 	}
 
@@ -340,7 +353,7 @@
 		}
 
 		idxd->groups[i] = group;
-		if (idxd->hw.version < DEVICE_VERSION_2 && !tc_override) {
+		if (idxd->hw.version <= DEVICE_VERSION_2 && !tc_override) {
 			group->tc_a = 1;
 			group->tc_b = 1;
 		} else {
@@ -437,6 +450,19 @@
 	dev_dbg(dev, "IDXD Perfmon Offset: %#x\n", idxd->perfmon_offset);
 }
 
+static void multi_u64_to_bmap(unsigned long *bmap, u64 *val, int count)
+{
+	int i, j, nr;
+
+	for (i = 0, nr = 0; i < count; i++) {
+		for (j = 0; j < BITS_PER_LONG_LONG; j++) {
+			if (val[i] & BIT(j))
+				set_bit(nr, bmap);
+			nr++;
+		}
+	}
+}
+
 static void idxd_read_caps(struct idxd_device *idxd)
 {
 	struct device *dev = &idxd->pdev->dev;
@@ -464,9 +490,9 @@
 	dev_dbg(dev, "group_cap: %#llx\n", idxd->hw.group_cap.bits);
 	idxd->max_groups = idxd->hw.group_cap.num_groups;
 	dev_dbg(dev, "max groups: %u\n", idxd->max_groups);
-	idxd->max_tokens = idxd->hw.group_cap.total_tokens;
-	dev_dbg(dev, "max tokens: %u\n", idxd->max_tokens);
-	idxd->nr_tokens = idxd->max_tokens;
+	idxd->max_rdbufs = idxd->hw.group_cap.total_rdbufs;
+	dev_dbg(dev, "max read buffers: %u\n", idxd->max_rdbufs);
+	idxd->nr_rdbufs = idxd->max_rdbufs;
 
 	/* read engine capabilities */
 	idxd->hw.engine_cap.bits =
@@ -491,6 +517,7 @@
 				IDXD_OPCAP_OFFSET + i * sizeof(u64));
 		dev_dbg(dev, "opcap[%d]: %#llx\n", i, idxd->hw.opcap.bits[i]);
 	}
+	multi_u64_to_bmap(idxd->opcap_bmap, &idxd->hw.opcap.bits[0], 4);
 }
 
 static struct idxd_device *idxd_alloc(struct pci_dev *pdev, struct idxd_driver_data *data)
@@ -512,6 +539,14 @@
 	if (idxd->id < 0)
 		return NULL;
 
+	idxd->opcap_bmap = kmalloc_array_node(BITS_TO_LONGS(IDXD_MAX_OPCAP_BITS),
+					      sizeof(unsigned long), GFP_KERNEL | __GFP_ZERO,
+					      dev_to_node(dev));
+	if (!idxd->opcap_bmap) {
+		ida_free(&idxd_ida, idxd->id);
+		return NULL;
+	}
+
 	device_initialize(conf_dev);
 	conf_dev->parent = dev;
 	conf_dev->bus = &dsa_bus_type;
@@ -695,6 +730,8 @@
 	dev_info(&pdev->dev, "Intel(R) Accelerator Device (v%x)\n",
 		 idxd->hw.version);
 
+	idxd->user_submission_safe = data->user_submission_safe;
+
 	return 0;
 
  err_dev_register:
@@ -797,11 +834,19 @@
 	int msixcnt = pci_msix_vec_count(pdev);
 	int i;
 
-	dev_dbg(&pdev->dev, "%s called\n", __func__);
+	idxd_unregister_devices(idxd);
+	/*
+	 * When ->release() is called for the idxd->conf_dev, it frees all the memory related
+	 * to the idxd context. The driver still needs those bits in order to do the rest of
+	 * the cleanup. However, we do need to unbound the idxd sub-driver. So take a ref
+	 * on the device here to hold off the freeing while allowing the idxd sub-driver
+	 * to unbind.
+	 */
+	get_device(idxd_confdev(idxd));
+	device_unregister(idxd_confdev(idxd));
 	idxd_shutdown(pdev);
 	if (device_pasid_enabled(idxd))
 		idxd_disable_system_pasid(idxd);
-	idxd_unregister_devices(idxd);
 
 	for (i = 0; i < msixcnt; i++) {
 		irq_entry = &idxd->irq_entries[i];
@@ -815,7 +860,7 @@
 	pci_disable_device(pdev);
 	destroy_workqueue(idxd->wq);
 	perfmon_pmu_remove(idxd);
-	device_unregister(idxd_confdev(idxd));
+	put_device(idxd_confdev(idxd));
 }
 
 static struct pci_driver idxd_pci_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/irq.c
@@ -63,6 +63,9 @@
 	int i;
 	bool err = false;
 
+	if (cause & IDXD_INTC_HALT_STATE)
+		goto halt;
+
 	if (cause & IDXD_INTC_ERR) {
 		spin_lock(&idxd->dev_lock);
 		for (i = 0; i < 4; i++)
@@ -121,6 +124,7 @@
 	if (!err)
 		return 0;
 
+halt:
 	gensts.bits = ioread32(idxd->reg_base + IDXD_GENSTATS_OFFSET);
 	if (gensts.state == IDXD_DEVICE_STATE_HALT) {
 		idxd->state = IDXD_DEV_HALTED;
@@ -133,9 +137,10 @@
 			INIT_WORK(&idxd->work, idxd_device_reinit);
 			queue_work(idxd->wq, &idxd->work);
 		} else {
-			spin_lock(&idxd->dev_lock);
+			idxd->state = IDXD_DEV_HALTED;
 			idxd_wqs_quiesce(idxd);
 			idxd_wqs_unmap_portal(idxd);
+			spin_lock(&idxd->dev_lock);
 			idxd_device_clear_state(idxd);
 			dev_err(&idxd->pdev->dev,
 				"idxd halted, need %s.\n",
@@ -228,11 +233,13 @@
 
 	spin_unlock(&irq_entry->list_lock);
 
-	list_for_each_entry(desc, &flist, list) {
+	list_for_each_entry_safe(desc, n, &flist, list) {
 		/*
 		 * Check against the original status as ABORT is software defined
 		 * and 0xff, which DSA_COMP_STATUS_MASK can mask out.
 		 */
+		list_del(&desc->list);
+
 		if (unlikely(desc->completion->status == IDXD_COMP_DESC_ABORT)) {
 			complete_desc(desc, IDXD_COMPLETE_ABORT);
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/perfmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/perfmon.c
@@ -529,14 +529,11 @@
 		return 0;
 
 	target = cpumask_any_but(cpu_online_mask, cpu);
-
 	/* migrate events if there is a valid target */
-	if (target < nr_cpu_ids)
+	if (target < nr_cpu_ids) {
 		cpumask_set_cpu(target, &perfmon_dsa_cpu_mask);
-	else
-		target = -1;
-
-	perf_pmu_migrate_context(&idxd_pmu->pmu, cpu, target);
+		perf_pmu_migrate_context(&idxd_pmu->pmu, cpu, target);
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/registers.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/registers.h
@@ -4,9 +4,6 @@
 #define _IDXD_REGISTERS_H_
 
 /* PCI Config */
-#define PCI_DEVICE_ID_INTEL_DSA_SPR0	0x0b25
-#define PCI_DEVICE_ID_INTEL_IAX_SPR0	0x0cfe
-
 #define DEVICE_VERSION_1		0x100
 #define DEVICE_VERSION_2		0x200
 
@@ -55,7 +52,8 @@
 		u64 priority:1;
 		u64 occupancy:1;
 		u64 occupancy_int:1;
-		u64 rsvd3:10;
+		u64 op_config:1;
+		u64 rsvd3:9;
 	};
 	u64 bits;
 } __packed;
@@ -65,9 +63,9 @@
 union group_cap_reg {
 	struct {
 		u64 num_groups:8;
-		u64 total_tokens:8;
-		u64 token_en:1;
-		u64 token_limit:1;
+		u64 total_rdbufs:8;	/* formerly total_tokens */
+		u64 rdbuf_ctrl:1;	/* formerly token_en */
+		u64 rdbuf_limit:1;	/* formerly token_limit */
 		u64 rsvd:46;
 	};
 	u64 bits;
@@ -91,6 +89,8 @@
 	u64 bits[4];
 };
 
+#define IDXD_MAX_OPCAP_BITS		256U
+
 #define IDXD_OPCAP_OFFSET		0x40
 
 #define IDXD_TABLE_OFFSET		0x60
@@ -111,7 +111,7 @@
 #define IDXD_GENCFG_OFFSET		0x80
 union gencfg_reg {
 	struct {
-		u32 token_limit:8;
+		u32 rdbuf_limit:8;
 		u32 rsvd:4;
 		u32 user_int_en:1;
 		u32 rsvd2:19;
@@ -158,6 +158,7 @@
 #define IDXD_INTC_CMD			0x02
 #define IDXD_INTC_OCCUPY			0x04
 #define IDXD_INTC_PERFMON_OVFL		0x08
+#define IDXD_INTC_HALT_STATE		0x10
 
 #define IDXD_CMD_OFFSET			0xa0
 union idxd_command_reg {
@@ -287,10 +288,10 @@
 		u32 tc_a:3;
 		u32 tc_b:3;
 		u32 rsvd:1;
-		u32 use_token_limit:1;
-		u32 tokens_reserved:8;
+		u32 use_rdbuf_limit:1;
+		u32 rdbufs_reserved:8;
 		u32 rsvd2:4;
-		u32 tokens_allowed:8;
+		u32 rdbufs_allowed:8;
 		u32 rsvd3:4;
 	};
 	u32 bits;
@@ -347,8 +348,11 @@
 
 		/* bytes 28-31 */
 		u32 rsvd8;
+
+		/* bytes 32-63 */
+		u64 op_config[4];
 	};
-	u32 bits[8];
+	u32 bits[16];
 } __packed;
 
 #define WQCFG_PASID_IDX                2
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/submit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/submit.c
@@ -106,6 +106,7 @@
 {
 	struct idxd_desc *d, *t, *found = NULL;
 	struct llist_node *head;
+	LIST_HEAD(flist);
 
 	desc->completion->status = IDXD_COMP_DESC_ABORT;
 	/*
@@ -120,7 +121,11 @@
 				found = desc;
 				continue;
 			}
-			list_add_tail(&desc->list, &ie->work_list);
+
+			if (d->completion->status)
+				list_add_tail(&d->list, &flist);
+			else
+				list_add_tail(&d->list, &ie->work_list);
 		}
 	}
 
@@ -130,6 +135,41 @@
 
 	if (found)
 		complete_desc(found, IDXD_COMPLETE_ABORT);
+
+	/*
+	 * complete_desc() will return desc to allocator and the desc can be
+	 * acquired by a different process and the desc->list can be modified.
+	 * Delete desc from list so the list trasversing does not get corrupted
+	 * by the other process.
+	 */
+	list_for_each_entry_safe(d, t, &flist, list) {
+		list_del_init(&d->list);
+		complete_desc(d, IDXD_COMPLETE_NORMAL);
+	}
+}
+
+/*
+ * ENQCMDS typically fail when the WQ is inactive or busy. On host submission, the driver
+ * has better control of number of descriptors being submitted to a shared wq by limiting
+ * the number of driver allocated descriptors to the wq size. However, when the swq is
+ * exported to a guest kernel, it may be shared with multiple guest kernels. This means
+ * the likelihood of getting busy returned on the swq when submitting goes significantly up.
+ * Having a tunable retry mechanism allows the driver to keep trying for a bit before giving
+ * up. The sysfs knob can be tuned by the system administrator.
+ */
+int idxd_enqcmds(struct idxd_wq *wq, void __iomem *portal, const void *desc)
+{
+	unsigned int retries = wq->enqcmds_retries;
+	int rc;
+
+	do {
+		rc = enqcmds(portal, desc);
+		if (rc == 0)
+			break;
+		cpu_relax();
+	} while (retries--);
+
+	return rc;
 }
 
 int idxd_submit_desc(struct idxd_wq *wq, struct idxd_desc *desc)
@@ -170,13 +210,7 @@
 	if (wq_dedicated(wq)) {
 		iosubmit_cmds512(portal, desc->hw, 1);
 	} else {
-		/*
-		 * It's not likely that we would receive queue full rejection
-		 * since the descriptor allocation gates at wq size. If we
-		 * receive a -EAGAIN, that means something went wrong such as the
-		 * device is not accepting descriptor at all.
-		 */
-		rc = enqcmds(portal, desc->hw);
+		rc = idxd_enqcmds(wq, portal, desc->hw);
 		if (rc < 0) {
 			percpu_ref_put(&wq->wq_active);
 			/* abort operation frees the descriptor */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/idxd/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/idxd/sysfs.c
@@ -99,17 +99,17 @@
 
 /* Group attributes */
 
-static void idxd_set_free_tokens(struct idxd_device *idxd)
+static void idxd_set_free_rdbufs(struct idxd_device *idxd)
 {
-	int i, tokens;
+	int i, rdbufs;
 
-	for (i = 0, tokens = 0; i < idxd->max_groups; i++) {
+	for (i = 0, rdbufs = 0; i < idxd->max_groups; i++) {
 		struct idxd_group *g = idxd->groups[i];
 
-		tokens += g->tokens_reserved;
+		rdbufs += g->rdbufs_reserved;
 	}
 
-	idxd->nr_tokens = idxd->max_tokens - tokens;
+	idxd->nr_rdbufs = idxd->max_rdbufs - rdbufs;
 }
 
 static ssize_t group_tokens_reserved_show(struct device *dev,
@@ -118,7 +118,7 @@
 {
 	struct idxd_group *group = confdev_to_group(dev);
 
-	return sysfs_emit(buf, "%u\n", group->tokens_reserved);
+	return sysfs_emit(buf, "%u\n", group->rdbufs_reserved);
 }
 
 static ssize_t group_tokens_reserved_store(struct device *dev,
@@ -143,14 +143,14 @@
 	if (idxd->state == IDXD_DEV_ENABLED)
 		return -EPERM;
 
-	if (val > idxd->max_tokens)
+	if (val > idxd->max_rdbufs)
 		return -EINVAL;
 
-	if (val > idxd->nr_tokens + group->tokens_reserved)
+	if (val > idxd->nr_rdbufs + group->rdbufs_reserved)
 		return -EINVAL;
 
-	group->tokens_reserved = val;
-	idxd_set_free_tokens(idxd);
+	group->rdbufs_reserved = val;
+	idxd_set_free_rdbufs(idxd);
 	return count;
 }
 
@@ -164,7 +164,7 @@
 {
 	struct idxd_group *group = confdev_to_group(dev);
 
-	return sysfs_emit(buf, "%u\n", group->tokens_allowed);
+	return sysfs_emit(buf, "%u\n", group->rdbufs_allowed);
 }
 
 static ssize_t group_tokens_allowed_store(struct device *dev,
@@ -190,10 +190,10 @@
 		return -EPERM;
 
 	if (val < 4 * group->num_engines ||
-	    val > group->tokens_reserved + idxd->nr_tokens)
+	    val > group->rdbufs_reserved + idxd->nr_rdbufs)
 		return -EINVAL;
 
-	group->tokens_allowed = val;
+	group->rdbufs_allowed = val;
 	return count;
 }
 
@@ -207,7 +207,7 @@
 {
 	struct idxd_group *group = confdev_to_group(dev);
 
-	return sysfs_emit(buf, "%u\n", group->use_token_limit);
+	return sysfs_emit(buf, "%u\n", group->use_rdbuf_limit);
 }
 
 static ssize_t group_use_token_limit_store(struct device *dev,
@@ -232,10 +232,10 @@
 	if (idxd->state == IDXD_DEV_ENABLED)
 		return -EPERM;
 
-	if (idxd->token_limit == 0)
+	if (idxd->rdbuf_limit == 0)
 		return -EPERM;
 
-	group->use_token_limit = !!val;
+	group->use_rdbuf_limit = !!val;
 	return count;
 }
 
@@ -327,7 +327,7 @@
 	if (idxd->state == IDXD_DEV_ENABLED)
 		return -EPERM;
 
-	if (idxd->hw.version < DEVICE_VERSION_2 && !tc_override)
+	if (idxd->hw.version <= DEVICE_VERSION_2 && !tc_override)
 		return -EPERM;
 
 	if (val < 0 || val > 7)
@@ -369,7 +369,7 @@
 	if (idxd->state == IDXD_DEV_ENABLED)
 		return -EPERM;
 
-	if (idxd->hw.version < DEVICE_VERSION_2 && !tc_override)
+	if (idxd->hw.version <= DEVICE_VERSION_2 && !tc_override)
 		return -EPERM;
 
 	if (val < 0 || val > 7)
@@ -842,6 +842,9 @@
 	u64 xfer_size;
 	int rc;
 
+	if (!test_bit(IDXD_FLAG_CONFIGURABLE, &idxd->flags))
+		return -EPERM;
+
 	if (wq->state != IDXD_WQ_DISABLED)
 		return -EPERM;
 
@@ -876,6 +879,9 @@
 	u64 batch_size;
 	int rc;
 
+	if (!test_bit(IDXD_FLAG_CONFIGURABLE, &idxd->flags))
+		return -EPERM;
+
 	if (wq->state != IDXD_WQ_DISABLED)
 		return -EPERM;
 
@@ -945,6 +951,126 @@
 static struct device_attribute dev_attr_wq_occupancy =
 		__ATTR(occupancy, 0444, wq_occupancy_show, NULL);
 
+static ssize_t op_cap_show_common(struct device *dev, char *buf, unsigned long *opcap_bmap)
+{
+	ssize_t pos;
+	int i;
+
+	pos = 0;
+	for (i = IDXD_MAX_OPCAP_BITS/64 - 1; i >= 0; i--) {
+		unsigned long val = opcap_bmap[i];
+
+		/* On systems where direct user submissions are not safe, we need to clear out
+		 * the BATCH capability from the capability mask in sysfs since we cannot support
+		 * that command on such systems.
+		 */
+		if (i == DSA_OPCODE_BATCH/64 && !confdev_to_idxd(dev)->user_submission_safe)
+			clear_bit(DSA_OPCODE_BATCH % 64, &val);
+
+		pos += sysfs_emit_at(buf, pos, "%*pb", 64, &val);
+		pos += sysfs_emit_at(buf, pos, "%c", i == 0 ? '\n' : ',');
+	}
+
+	return pos;
+}
+
+static ssize_t wq_op_config_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	struct idxd_wq *wq = confdev_to_wq(dev);
+
+	return op_cap_show_common(dev, buf, wq->opcap_bmap);
+}
+
+static int idxd_verify_supported_opcap(struct idxd_device *idxd, unsigned long *opmask)
+{
+	int bit;
+
+	/*
+	 * The OPCAP is defined as 256 bits that represents each operation the device
+	 * supports per bit. Iterate through all the bits and check if the input mask
+	 * is set for bits that are not set in the OPCAP for the device. If no OPCAP
+	 * bit is set and input mask has the bit set, then return error.
+	 */
+	for_each_set_bit(bit, opmask, IDXD_MAX_OPCAP_BITS) {
+		if (!test_bit(bit, idxd->opcap_bmap))
+			return -EINVAL;
+	}
+
+	return 0;
+}
+
+static ssize_t wq_op_config_store(struct device *dev, struct device_attribute *attr,
+				  const char *buf, size_t count)
+{
+	struct idxd_wq *wq = confdev_to_wq(dev);
+	struct idxd_device *idxd = wq->idxd;
+	unsigned long *opmask;
+	int rc;
+
+	if (wq->state != IDXD_WQ_DISABLED)
+		return -EPERM;
+
+	opmask = bitmap_zalloc(IDXD_MAX_OPCAP_BITS, GFP_KERNEL);
+	if (!opmask)
+		return -ENOMEM;
+
+	rc = bitmap_parse(buf, count, opmask, IDXD_MAX_OPCAP_BITS);
+	if (rc < 0)
+		goto err;
+
+	rc = idxd_verify_supported_opcap(idxd, opmask);
+	if (rc < 0)
+		goto err;
+
+	bitmap_copy(wq->opcap_bmap, opmask, IDXD_MAX_OPCAP_BITS);
+
+	bitmap_free(opmask);
+	return count;
+
+err:
+	bitmap_free(opmask);
+	return rc;
+}
+
+static struct device_attribute dev_attr_wq_op_config =
+		__ATTR(op_config, 0644, wq_op_config_show, wq_op_config_store);
+
+static ssize_t wq_enqcmds_retries_show(struct device *dev,
+				       struct device_attribute *attr, char *buf)
+{
+	struct idxd_wq *wq = confdev_to_wq(dev);
+
+	if (wq_dedicated(wq))
+		return -EOPNOTSUPP;
+
+	return sysfs_emit(buf, "%u\n", wq->enqcmds_retries);
+}
+
+static ssize_t wq_enqcmds_retries_store(struct device *dev, struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	struct idxd_wq *wq = confdev_to_wq(dev);
+	int rc;
+	unsigned int retries;
+
+	if (wq_dedicated(wq))
+		return -EOPNOTSUPP;
+
+	rc = kstrtouint(buf, 10, &retries);
+	if (rc < 0)
+		return rc;
+
+	if (retries > IDXD_ENQCMDS_MAX_RETRIES)
+		retries = IDXD_ENQCMDS_MAX_RETRIES;
+
+	wq->enqcmds_retries = retries;
+	return count;
+}
+
+static struct device_attribute dev_attr_wq_enqcmds_retries =
+		__ATTR(enqcmds_retries, 0644, wq_enqcmds_retries_show, wq_enqcmds_retries_store);
+
 static struct attribute *idxd_wq_attributes[] = {
 	&dev_attr_wq_clients.attr,
 	&dev_attr_wq_state.attr,
@@ -961,11 +1087,34 @@
 	&dev_attr_wq_max_batch_size.attr,
 	&dev_attr_wq_ats_disable.attr,
 	&dev_attr_wq_occupancy.attr,
+	&dev_attr_wq_enqcmds_retries.attr,
+	&dev_attr_wq_op_config.attr,
 	NULL,
 };
 
+static bool idxd_wq_attr_op_config_invisible(struct attribute *attr,
+					     struct idxd_device *idxd)
+{
+	return attr == &dev_attr_wq_op_config.attr &&
+	       !idxd->hw.wq_cap.op_config;
+}
+
+static umode_t idxd_wq_attr_visible(struct kobject *kobj,
+				    struct attribute *attr, int n)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct idxd_wq *wq = confdev_to_wq(dev);
+	struct idxd_device *idxd = wq->idxd;
+
+	if (idxd_wq_attr_op_config_invisible(attr, idxd))
+		return 0;
+
+	return attr->mode;
+}
+
 static const struct attribute_group idxd_wq_attribute_group = {
 	.attrs = idxd_wq_attributes,
+	.is_visible = idxd_wq_attr_visible,
 };
 
 static const struct attribute_group *idxd_wq_attribute_groups[] = {
@@ -977,6 +1126,7 @@
 {
 	struct idxd_wq *wq = confdev_to_wq(dev);
 
+	bitmap_free(wq->opcap_bmap);
 	kfree(wq->wqcfg);
 	kfree(wq);
 }
@@ -1066,14 +1216,8 @@
 			   struct device_attribute *attr, char *buf)
 {
 	struct idxd_device *idxd = confdev_to_idxd(dev);
-	int i, rc = 0;
 
-	for (i = 0; i < 4; i++)
-		rc += sysfs_emit_at(buf, rc, "%#llx ", idxd->hw.opcap.bits[i]);
-
-	rc--;
-	rc += sysfs_emit_at(buf, rc, "\n");
-	return rc;
+	return op_cap_show_common(dev, buf, idxd->opcap_bmap);
 }
 static DEVICE_ATTR_RO(op_cap);
 
@@ -1161,7 +1305,7 @@
 {
 	struct idxd_device *idxd = confdev_to_idxd(dev);
 
-	return sysfs_emit(buf, "%u\n", idxd->max_tokens);
+	return sysfs_emit(buf, "%u\n", idxd->max_rdbufs);
 }
 static DEVICE_ATTR_RO(max_tokens);
 
@@ -1170,7 +1314,7 @@
 {
 	struct idxd_device *idxd = confdev_to_idxd(dev);
 
-	return sysfs_emit(buf, "%u\n", idxd->token_limit);
+	return sysfs_emit(buf, "%u\n", idxd->rdbuf_limit);
 }
 
 static ssize_t token_limit_store(struct device *dev,
@@ -1191,13 +1335,13 @@
 	if (!test_bit(IDXD_FLAG_CONFIGURABLE, &idxd->flags))
 		return -EPERM;
 
-	if (!idxd->hw.group_cap.token_limit)
+	if (!idxd->hw.group_cap.rdbuf_limit)
 		return -EPERM;
 
-	if (val > idxd->hw.group_cap.total_tokens)
+	if (val > idxd->hw.group_cap.total_rdbufs)
 		return -EINVAL;
 
-	idxd->token_limit = val;
+	idxd->rdbuf_limit = val;
 	return count;
 }
 static DEVICE_ATTR_RW(token_limit);
@@ -1271,6 +1415,7 @@
 	kfree(idxd->irq_entries);
 	kfree(idxd->int_handles);
 	ida_free(&idxd_ida, idxd->id);
+	bitmap_free(idxd->opcap_bmap);
 	kfree(idxd);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/imx-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/imx-dma.c
@@ -1047,7 +1047,7 @@
 		return -ENOMEM;
 
 	imxdma->dev = &pdev->dev;
-	imxdma->devtype = (enum imx_dma_type)of_device_get_match_data(&pdev->dev);
+	imxdma->devtype = (uintptr_t)of_device_get_match_data(&pdev->dev);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	imxdma->base = devm_ioremap_resource(&pdev->dev, res);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/imx-sdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/imx-sdma.c
@@ -198,12 +198,12 @@
 	s32 per_2_firi_addr;
 	s32 mcu_2_firi_addr;
 	s32 uart_2_per_addr;
-	s32 uart_2_mcu_ram_addr;
+	s32 uart_2_mcu_addr;
 	s32 per_2_app_addr;
 	s32 mcu_2_app_addr;
 	s32 per_2_per_addr;
 	s32 uartsh_2_per_addr;
-	s32 uartsh_2_mcu_ram_addr;
+	s32 uartsh_2_mcu_addr;
 	s32 per_2_shp_addr;
 	s32 mcu_2_shp_addr;
 	s32 ata_2_mcu_addr;
@@ -232,8 +232,8 @@
 	s32 mcu_2_ecspi_addr;
 	s32 mcu_2_sai_addr;
 	s32 sai_2_mcu_addr;
-	s32 uart_2_mcu_addr;
-	s32 uartsh_2_mcu_addr;
+	s32 uart_2_mcu_rom_addr;
+	s32 uartsh_2_mcu_rom_addr;
 	/* End of v3 array */
 	s32 mcu_2_zqspi_addr;
 	/* End of v4 array */
@@ -1428,10 +1428,12 @@
 		sdma_config_ownership(sdmac, false, true, false);
 
 	if (sdma_load_context(sdmac))
-		goto err_desc_out;
+		goto err_bd_out;
 
 	return desc;
 
+err_bd_out:
+	sdma_free_bd(desc);
 err_desc_out:
 	kfree(desc);
 err_out:
@@ -1780,17 +1782,17 @@
 			saddr_arr[i] = addr_arr[i];
 
 	/*
-	 * get uart_2_mcu_addr/uartsh_2_mcu_addr rom script specially because
-	 * they are now replaced by uart_2_mcu_ram_addr/uartsh_2_mcu_ram_addr
-	 * to be compatible with legacy freescale/nxp sdma firmware, and they
-	 * are located in the bottom part of sdma_script_start_addrs which are
-	 * beyond the SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V1.
+	 * For compatibility with NXP internal legacy kernel before 4.19 which
+	 * is based on uart ram script and mainline kernel based on uart rom
+	 * script, both uart ram/rom scripts are present in newer sdma
+	 * firmware. Use the rom versions if they are present (V3 or newer).
 	 */
-	if (addr->uart_2_mcu_addr)
-		sdma->script_addrs->uart_2_mcu_addr = addr->uart_2_mcu_addr;
-	if (addr->uartsh_2_mcu_addr)
-		sdma->script_addrs->uartsh_2_mcu_addr = addr->uartsh_2_mcu_addr;
-
+	if (sdma->script_number >= SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3) {
+		if (addr->uart_2_mcu_rom_addr)
+			sdma->script_addrs->uart_2_mcu_addr = addr->uart_2_mcu_rom_addr;
+		if (addr->uartsh_2_mcu_rom_addr)
+			sdma->script_addrs->uartsh_2_mcu_addr = addr->uartsh_2_mcu_rom_addr;
+	}
 }
 
 static void sdma_load_firmware(const struct firmware *fw, void *context)
@@ -1869,7 +1871,7 @@
 	u32 reg, val, shift, num_map, i;
 	int ret = 0;
 
-	if (IS_ERR(np) || IS_ERR(gpr_np))
+	if (IS_ERR(np) || !gpr_np)
 		goto out;
 
 	event_remap = of_find_property(np, propname, NULL);
@@ -1917,7 +1919,7 @@
 	}
 
 out:
-	if (!IS_ERR(gpr_np))
+	if (gpr_np)
 		of_node_put(gpr_np);
 
 	return ret;
@@ -2264,7 +2266,7 @@
 #if IS_ENABLED(CONFIG_SOC_IMX6Q)
 MODULE_FIRMWARE("imx/sdma/sdma-imx6q.bin");
 #endif
-#if IS_ENABLED(CONFIG_SOC_IMX7D)
+#if IS_ENABLED(CONFIG_SOC_IMX7D) || IS_ENABLED(CONFIG_SOC_IMX8M)
 MODULE_FIRMWARE("imx/sdma/sdma-imx7d.bin");
 #endif
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ioat/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ioat/dma.c
@@ -656,7 +656,7 @@
 	if (active - i == 0) {
 		dev_dbg(to_dev(ioat_chan), "%s: cancel completion timeout\n",
 			__func__);
-		mod_timer(&ioat_chan->timer, jiffies + IDLE_TIMEOUT);
+		mod_timer_pending(&ioat_chan->timer, jiffies + IDLE_TIMEOUT);
 	}
 
 	/* microsecond delay by sysfs variable  per pending descriptor */
@@ -682,7 +682,7 @@
 
 		if (chanerr &
 		    (IOAT_CHANERR_HANDLE_MASK | IOAT_CHANERR_RECOVER_MASK)) {
-			mod_timer(&ioat_chan->timer, jiffies + IDLE_TIMEOUT);
+			mod_timer_pending(&ioat_chan->timer, jiffies + IDLE_TIMEOUT);
 			ioat_eh(ioat_chan);
 		}
 	}
@@ -879,7 +879,7 @@
 	}
 
 	if (test_and_clear_bit(IOAT_CHAN_ACTIVE, &ioat_chan->state))
-		mod_timer(&ioat_chan->timer, jiffies + IDLE_TIMEOUT);
+		mod_timer_pending(&ioat_chan->timer, jiffies + IDLE_TIMEOUT);
 }
 
 static void ioat_reboot_chan(struct ioatdma_chan *ioat_chan)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ioat/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ioat/init.c
@@ -15,7 +15,6 @@
 #include <linux/workqueue.h>
 #include <linux/prefetch.h>
 #include <linux/dca.h>
-#include <linux/aer.h>
 #include <linux/sizes.h>
 #include "dma.h"
 #include "registers.h"
@@ -535,18 +534,6 @@
 	return err;
 }
 
-static int ioat_register(struct ioatdma_device *ioat_dma)
-{
-	int err = dma_async_device_register(&ioat_dma->dma_dev);
-
-	if (err) {
-		ioat_disable_interrupts(ioat_dma);
-		dma_pool_destroy(ioat_dma->completion_pool);
-	}
-
-	return err;
-}
-
 static void ioat_dma_remove(struct ioatdma_device *ioat_dma)
 {
 	struct dma_device *dma = &ioat_dma->dma_dev;
@@ -1181,9 +1168,9 @@
 		       ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
 	}
 
-	err = ioat_register(ioat_dma);
+	err = dma_async_device_register(&ioat_dma->dma_dev);
 	if (err)
-		return err;
+		goto err_disable_interrupts;
 
 	ioat_kobject_add(ioat_dma, &ioat_ktype);
 
@@ -1191,21 +1178,30 @@
 		ioat_dma->dca = ioat_dca_init(pdev, ioat_dma->reg_base);
 
 	/* disable relaxed ordering */
-	err = pcie_capability_read_word(pdev, IOAT_DEVCTRL_OFFSET, &val16);
-	if (err)
-		return pcibios_err_to_errno(err);
+	err = pcie_capability_read_word(pdev, PCI_EXP_DEVCTL, &val16);
+	if (err) {
+		err = pcibios_err_to_errno(err);
+		goto err_disable_interrupts;
+	}
 
 	/* clear relaxed ordering enable */
-	val16 &= ~IOAT_DEVCTRL_ROE;
-	err = pcie_capability_write_word(pdev, IOAT_DEVCTRL_OFFSET, val16);
-	if (err)
-		return pcibios_err_to_errno(err);
+	val16 &= ~PCI_EXP_DEVCTL_RELAX_EN;
+	err = pcie_capability_write_word(pdev, PCI_EXP_DEVCTL, val16);
+	if (err) {
+		err = pcibios_err_to_errno(err);
+		goto err_disable_interrupts;
+	}
 
 	if (ioat_dma->cap & IOAT_CAP_DPS)
 		writeb(ioat_pending_level + 1,
 		       ioat_dma->reg_base + IOAT_PREFETCH_LIMIT_OFFSET);
 
 	return 0;
+
+err_disable_interrupts:
+	ioat_disable_interrupts(ioat_dma);
+	dma_pool_destroy(ioat_dma->completion_pool);
+	return err;
 }
 
 static void ioat_shutdown(struct pci_dev *pdev)
@@ -1350,6 +1346,8 @@
 	void __iomem * const *iomap;
 	struct device *dev = &pdev->dev;
 	struct ioatdma_device *device;
+	unsigned int i;
+	u8 version;
 	int err;
 
 	err = pcim_enable_device(pdev);
@@ -1363,15 +1361,13 @@
 	if (!iomap)
 		return -ENOMEM;
 
-	err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
-	if (err)
-		err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
-	if (err)
-		return err;
+	version = readb(iomap[IOAT_MMIO_BAR] + IOAT_VER_OFFSET);
+	if (version < IOAT_VER_3_0)
+		return -ENODEV;
 
-	err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
 	if (err)
-		err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
 	if (err)
 		return err;
 
@@ -1381,22 +1377,19 @@
 	pci_set_master(pdev);
 	pci_set_drvdata(pdev, device);
 
-	device->version = readb(device->reg_base + IOAT_VER_OFFSET);
+	device->version = version;
 	if (device->version >= IOAT_VER_3_4)
 		ioat_dca_enabled = 0;
-	if (device->version >= IOAT_VER_3_0) {
-		if (is_skx_ioat(pdev))
-			device->version = IOAT_VER_3_2;
-		err = ioat3_dma_probe(device, ioat_dca_enabled);
-
-		if (device->version >= IOAT_VER_3_3)
-			pci_enable_pcie_error_reporting(pdev);
-	} else
-		return -ENODEV;
 
+	if (is_skx_ioat(pdev))
+		device->version = IOAT_VER_3_2;
+
+	err = ioat3_dma_probe(device, ioat_dca_enabled);
 	if (err) {
+		for (i = 0; i < IOAT_MAX_CHANS; i++)
+			kfree(device->idx[i]);
+		kfree(device);
 		dev_err(dev, "Intel(R) I/OAT DMA Engine init failed\n");
-		pci_disable_pcie_error_reporting(pdev);
 		return -ENODEV;
 	}
 
@@ -1419,7 +1412,6 @@
 		device->dca = NULL;
 	}
 
-	pci_disable_pcie_error_reporting(pdev);
 	ioat_dma_remove(device);
 }
 
@@ -1458,6 +1450,7 @@
 static void __exit ioat_exit_module(void)
 {
 	pci_unregister_driver(&ioat_pci_driver);
+	kmem_cache_destroy(ioat_sed_cache);
 	kmem_cache_destroy(ioat_cache);
 }
 module_exit(ioat_exit_module);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ioat/registers.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ioat/registers.h
@@ -14,13 +14,6 @@
 #define IOAT_PCI_CHANERR_INT_OFFSET		0x180
 #define IOAT_PCI_CHANERRMASK_INT_OFFSET		0x184
 
-/* PCIe config registers */
-
-/* EXPCAPID + N */
-#define IOAT_DEVCTRL_OFFSET			0x8
-/* relaxed ordering enable */
-#define IOAT_DEVCTRL_ROE			0x10
-
 /* MMIO Device Registers */
 #define IOAT_CHANCNT_OFFSET			0x00	/*  8-bit */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/lgm/lgm-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/lgm/lgm-dma.c
@@ -914,7 +914,7 @@
 	}
 }
 
-static int ldma_cfg_init(struct ldma_dev *d)
+static int ldma_parse_dt(struct ldma_dev *d)
 {
 	struct fwnode_handle *fwnode = dev_fwnode(d->dev);
 	struct ldma_port *p;
@@ -1593,11 +1593,12 @@
 	d->core_clk = devm_clk_get_optional(dev, NULL);
 	if (IS_ERR(d->core_clk))
 		return PTR_ERR(d->core_clk);
-	clk_prepare_enable(d->core_clk);
 
 	d->rst = devm_reset_control_get_optional(dev, NULL);
 	if (IS_ERR(d->rst))
 		return PTR_ERR(d->rst);
+
+	clk_prepare_enable(d->core_clk);
 	reset_control_deassert(d->rst);
 
 	ret = devm_add_action_or_reset(dev, ldma_clk_disable, d);
@@ -1660,10 +1661,6 @@
 		p->ldev = d;
 	}
 
-	ret = ldma_cfg_init(d);
-	if (ret)
-		return ret;
-
 	dma_dev->dev = &pdev->dev;
 
 	ch_mask = (unsigned long)d->channels_mask;
@@ -1674,6 +1671,10 @@
 			ldma_dma_init_v3X(j, d);
 	}
 
+	ret = ldma_parse_dt(d);
+	if (ret)
+		return ret;
+
 	dma_dev->device_alloc_chan_resources = ldma_alloc_chan_resources;
 	dma_dev->device_free_chan_resources = ldma_free_chan_resources;
 	dma_dev->device_terminate_all = ldma_terminate_all;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/mcf-edma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/mcf-edma.c
@@ -191,7 +191,13 @@
 		return -EINVAL;
 	}
 
-	chans = pdata->dma_channels;
+	if (!pdata->dma_channels) {
+		dev_info(&pdev->dev, "setting default channel number to 64");
+		chans = 64;
+	} else {
+		chans = pdata->dma_channels;
+	}
+
 	len = sizeof(*mcf_edma) + sizeof(*mcf_chan) * chans;
 	mcf_edma = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
 	if (!mcf_edma)
@@ -203,11 +209,6 @@
 	mcf_edma->drvdata = &mcf_data;
 	mcf_edma->big_endian = 1;
 
-	if (!mcf_edma->n_chans) {
-		dev_info(&pdev->dev, "setting default channel number to 64");
-		mcf_edma->n_chans = 64;
-	}
-
 	mutex_init(&mcf_edma->fsl_edma_mutex);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/mediatek/mtk-uart-apdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/mediatek/mtk-uart-apdma.c
@@ -274,7 +274,7 @@
 	unsigned int status;
 	int ret;
 
-	ret = pm_runtime_get_sync(mtkd->ddev.dev);
+	ret = pm_runtime_resume_and_get(mtkd->ddev.dev);
 	if (ret < 0) {
 		pm_runtime_put_noidle(chan->device->dev);
 		return ret;
@@ -288,18 +288,21 @@
 	ret = readx_poll_timeout(readl, c->base + VFF_EN,
 			  status, !status, 10, 100);
 	if (ret)
-		return ret;
+		goto err_pm;
 
 	ret = request_irq(c->irq, mtk_uart_apdma_irq_handler,
 			  IRQF_TRIGGER_NONE, KBUILD_MODNAME, chan);
 	if (ret < 0) {
 		dev_err(chan->device->dev, "Can't request dma IRQ\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_pm;
 	}
 
 	if (mtkd->support_33bits)
 		mtk_uart_apdma_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_CLR_B);
 
+err_pm:
+	pm_runtime_put_noidle(mtkd->ddev.dev);
 	return ret;
 }
 
@@ -448,9 +451,8 @@
 	mtk_uart_apdma_write(c, VFF_EN, VFF_EN_CLR_B);
 	mtk_uart_apdma_write(c, VFF_INT_EN, VFF_INT_EN_CLR_B);
 
-	synchronize_irq(c->irq);
-
 	spin_unlock_irqrestore(&c->vc.lock, flags);
+	synchronize_irq(c->irq);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/mmp_pdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/mmp_pdma.c
@@ -727,12 +727,6 @@
 
 	chan->dir = direction;
 	chan->dev_addr = addr;
-	/* FIXME: drivers should be ported over to use the filter
-	 * function. Once that's done, the following two lines can
-	 * be removed.
-	 */
-	if (cfg->slave_id)
-		chan->drcmr = cfg->slave_id;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/mv_xor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/mv_xor.c
@@ -1393,6 +1393,7 @@
 			irq = irq_of_parse_and_map(np, 0);
 			if (!irq) {
 				ret = -ENODEV;
+				of_node_put(np);
 				goto err_channel_add;
 			}
 
@@ -1401,6 +1402,7 @@
 			if (IS_ERR(chan)) {
 				ret = PTR_ERR(chan);
 				irq_dispose_mapping(irq);
+				of_node_put(np);
 				goto err_channel_add;
 			}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/mv_xor_v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/mv_xor_v2.c
@@ -756,7 +756,7 @@
 
 	xor_dev->clk = devm_clk_get(&pdev->dev, NULL);
 	if (PTR_ERR(xor_dev->clk) == -EPROBE_DEFER) {
-		ret = EPROBE_DEFER;
+		ret = -EPROBE_DEFER;
 		goto disable_reg_clk;
 	}
 	if (!IS_ERR(xor_dev->clk)) {
@@ -899,6 +899,7 @@
 	tasklet_kill(&xor_dev->irq_tasklet);
 
 	clk_disable_unprepare(xor_dev->clk);
+	clk_disable_unprepare(xor_dev->reg_clk);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/mxs-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/mxs-dma.c
@@ -670,7 +670,7 @@
 	return mxs_chan->status;
 }
 
-static int __init mxs_dma_init(struct mxs_dma_engine *mxs_dma)
+static int mxs_dma_init(struct mxs_dma_engine *mxs_dma)
 {
 	int ret;
 
@@ -741,7 +741,7 @@
 				     ofdma->of_node);
 }
 
-static int __init mxs_dma_probe(struct platform_device *pdev)
+static int mxs_dma_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
 	const struct mxs_dma_type *dma_type;
@@ -839,10 +839,7 @@
 		.name	= "mxs-dma",
 		.of_match_table = mxs_dma_dt_ids,
 	},
+	.probe = mxs_dma_probe,
 };
 
-static int __init mxs_dma_module_init(void)
-{
-	return platform_driver_probe(&mxs_dma_driver, mxs_dma_probe);
-}
-subsys_initcall(mxs_dma_module_init);
+builtin_platform_driver(mxs_dma_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/owl-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/owl-dma.c
@@ -249,7 +249,7 @@
 	else
 		regval &= ~val;
 
-	writel(val, pchan->base + reg);
+	writel(regval, pchan->base + reg);
 }
 
 static void pchan_writel(struct owl_dma_pchan *pchan, u32 reg, u32 data)
@@ -273,7 +273,7 @@
 	else
 		regval &= ~val;
 
-	writel(val, od->base + reg);
+	writel(regval, od->base + reg);
 }
 
 static void dma_writel(struct owl_dma *od, u32 reg, u32 data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/pl330.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/pl330.c
@@ -404,6 +404,12 @@
 	 */
 	BUSY,
 	/*
+	 * Pause was called while descriptor was BUSY. Due to hardware
+	 * limitations, only termination is possible for descriptors
+	 * that have been paused.
+	 */
+	PAUSED,
+	/*
 	 * Sitting on the channel work_list but xfer done
 	 * by PL330 core
 	 */
@@ -1050,7 +1056,7 @@
 	return true;
 }
 
-static bool _start(struct pl330_thread *thrd)
+static bool pl330_start_thread(struct pl330_thread *thrd)
 {
 	switch (_state(thrd)) {
 	case PL330_STATE_FAULT_COMPLETING:
@@ -1702,7 +1708,7 @@
 			thrd->req_running = -1;
 
 			/* Get going again ASAP */
-			_start(thrd);
+			pl330_start_thread(thrd);
 
 			/* For now, just make a list of callbacks to be done */
 			list_add_tail(&descdone->rqd, &pl330->req_done);
@@ -2041,7 +2047,7 @@
 	list_for_each_entry(desc, &pch->work_list, node) {
 
 		/* If already submitted */
-		if (desc->status == BUSY)
+		if (desc->status == BUSY || desc->status == PAUSED)
 			continue;
 
 		ret = pl330_submit_req(pch->thread, desc);
@@ -2089,7 +2095,7 @@
 	} else {
 		/* Make sure the PL330 Channel thread is active */
 		spin_lock(&pch->thread->dmac->lock);
-		_start(pch->thread);
+		pl330_start_thread(pch->thread);
 		spin_unlock(&pch->thread->dmac->lock);
 	}
 
@@ -2107,7 +2113,7 @@
 			if (power_down) {
 				pch->active = true;
 				spin_lock(&pch->thread->dmac->lock);
-				_start(pch->thread);
+				pl330_start_thread(pch->thread);
 				spin_unlock(&pch->thread->dmac->lock);
 				power_down = false;
 			}
@@ -2326,6 +2332,7 @@
 {
 	struct dma_pl330_chan *pch = to_pchan(chan);
 	struct pl330_dmac *pl330 = pch->dmac;
+	struct dma_pl330_desc *desc;
 	unsigned long flags;
 
 	pm_runtime_get_sync(pl330->ddma.dev);
@@ -2335,6 +2342,10 @@
 	_stop(pch->thread);
 	spin_unlock(&pl330->lock);
 
+	list_for_each_entry(desc, &pch->work_list, node) {
+		if (desc->status == BUSY)
+			desc->status = PAUSED;
+	}
 	spin_unlock_irqrestore(&pch->lock, flags);
 	pm_runtime_mark_last_busy(pl330->ddma.dev);
 	pm_runtime_put_autosuspend(pl330->ddma.dev);
@@ -2425,7 +2436,7 @@
 		else if (running && desc == running)
 			transferred =
 				pl330_get_current_xferred_count(pch, desc);
-		else if (desc->status == BUSY)
+		else if (desc->status == BUSY || desc->status == PAUSED)
 			/*
 			 * Busy but not running means either just enqueued,
 			 * or finished and not yet marked done
@@ -2442,6 +2453,9 @@
 			case DONE:
 				ret = DMA_COMPLETE;
 				break;
+			case PAUSED:
+				ret = DMA_PAUSED;
+				break;
 			case PREP:
 			case BUSY:
 				ret = DMA_IN_PROGRESS;
@@ -2589,7 +2603,7 @@
 
 	/* If the DMAC pool is empty, alloc new */
 	if (!desc) {
-		DEFINE_SPINLOCK(lock);
+		static DEFINE_SPINLOCK(lock);
 		LIST_HEAD(pool);
 
 		if (!add_desc(&pool, &lock, GFP_ATOMIC, 1))
@@ -2752,7 +2766,7 @@
 		return NULL;
 
 	pch->cyclic = true;
-	desc->txd.flags = flags;
+	desc->txd.flags = (enum dma_ctrl_flags) flags;
 
 	return &desc->txd;
 }
@@ -2804,7 +2818,7 @@
 
 	desc->bytes_requested = len;
 
-	desc->txd.flags = flags;
+	desc->txd.flags = (enum dma_ctrl_flags) flags;
 
 	return &desc->txd;
 }
@@ -2889,7 +2903,7 @@
 	}
 
 	/* Return the last desc in the chain */
-	desc->txd.flags = flg;
+	desc->txd.flags = (enum dma_ctrl_flags) flg;
 	return &desc->txd;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ptdma/ptdma-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ptdma/ptdma-dev.c
@@ -71,12 +71,13 @@
 	bool soc = FIELD_GET(DWORD0_SOC, desc->dw0);
 	u8 *q_desc = (u8 *)&cmd_q->qbase[cmd_q->qidx];
 	u32 tail;
+	unsigned long flags;
 
 	if (soc) {
 		desc->dw0 |= FIELD_PREP(DWORD0_IOC, desc->dw0);
 		desc->dw0 &= ~DWORD0_SOC;
 	}
-	mutex_lock(&cmd_q->q_mutex);
+	spin_lock_irqsave(&cmd_q->q_lock, flags);
 
 	/* Copy 32-byte command descriptor to hw queue. */
 	memcpy(q_desc, desc, 32);
@@ -91,7 +92,7 @@
 
 	/* Turn the queue back on using our cached control register */
 	pt_start_queue(cmd_q);
-	mutex_unlock(&cmd_q->q_mutex);
+	spin_unlock_irqrestore(&cmd_q->q_lock, flags);
 
 	return 0;
 }
@@ -197,7 +198,7 @@
 
 	cmd_q->pt = pt;
 	cmd_q->dma_pool = dma_pool;
-	mutex_init(&cmd_q->q_mutex);
+	spin_lock_init(&cmd_q->q_lock);
 
 	/* Page alignment satisfies our needs for N <= 128 */
 	cmd_q->qsize = Q_SIZE(Q_DESC_SIZE);
@@ -207,7 +208,7 @@
 	if (!cmd_q->qbase) {
 		dev_err(dev, "unable to allocate command queue\n");
 		ret = -ENOMEM;
-		goto e_dma_alloc;
+		goto e_destroy_pool;
 	}
 
 	cmd_q->qidx = 0;
@@ -229,8 +230,10 @@
 
 	/* Request an irq */
 	ret = request_irq(pt->pt_irq, pt_core_irq_handler, 0, dev_name(pt->dev), pt);
-	if (ret)
-		goto e_pool;
+	if (ret) {
+		dev_err(dev, "unable to allocate an IRQ\n");
+		goto e_free_dma;
+	}
 
 	/* Update the device registers with queue information. */
 	cmd_q->qcontrol &= ~CMD_Q_SIZE;
@@ -250,21 +253,20 @@
 	/* Register the DMA engine support */
 	ret = pt_dmaengine_register(pt);
 	if (ret)
-		goto e_dmaengine;
+		goto e_free_irq;
 
 	/* Set up debugfs entries */
 	ptdma_debugfs_setup(pt);
 
 	return 0;
 
-e_dmaengine:
+e_free_irq:
 	free_irq(pt->pt_irq, pt);
 
-e_dma_alloc:
+e_free_dma:
 	dma_free_coherent(dev, cmd_q->qsize, cmd_q->qbase, cmd_q->qbase_dma);
 
-e_pool:
-	dev_err(dev, "unable to allocate an IRQ\n");
+e_destroy_pool:
 	dma_pool_destroy(pt->cmd_q.dma_pool);
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ptdma/ptdma-dmaengine.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ptdma/ptdma-dmaengine.c
@@ -361,8 +361,6 @@
 	chan->vc.desc_free = pt_do_cleanup;
 	vchan_init(&chan->vc, dma_dev);
 
-	dma_set_mask_and_coherent(pt->dev, DMA_BIT_MASK(64));
-
 	ret = dma_async_device_register(dma_dev);
 	if (ret)
 		goto err_reg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ptdma/ptdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ptdma/ptdma.h
@@ -196,7 +196,7 @@
 	struct ptdma_desc *qbase;
 
 	/* Aligned queue start address (per requirement) */
-	struct mutex q_mutex ____cacheline_aligned;
+	spinlock_t q_lock ____cacheline_aligned;
 	unsigned int qidx;
 
 	unsigned int qsize;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/pxa_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/pxa_dma.c
@@ -722,7 +722,6 @@
 	dma_addr_t dma;
 	struct pxad_desc_sw *sw_desc = to_pxad_sw_desc(vd);
 
-	BUG_ON(sw_desc->nb_desc == 0);
 	for (i = sw_desc->nb_desc - 1; i >= 0; i--) {
 		if (i > 0)
 			dma = sw_desc->hw_desc[i - 1]->ddadr;
@@ -910,13 +909,6 @@
 		*dcmd |= PXA_DCMD_BURST16;
 	else if (maxburst == 32)
 		*dcmd |= PXA_DCMD_BURST32;
-
-	/* FIXME: drivers should be ported over to use the filter
-	 * function. Once that's done, the following two lines can
-	 * be removed.
-	 */
-	if (chan->cfg.slave_id)
-		chan->drcmr = chan->cfg.slave_id;
 }
 
 static struct dma_async_tx_descriptor *
@@ -1255,14 +1247,14 @@
 		return -ENOMEM;
 
 	for (i = 0; i < nb_phy_chans; i++)
-		if (platform_get_irq(op, i) > 0)
+		if (platform_get_irq_optional(op, i) > 0)
 			nr_irq++;
 
 	for (i = 0; i < nb_phy_chans; i++) {
 		phy = &pdev->phys[i];
 		phy->base = pdev->base;
 		phy->idx = i;
-		irq = platform_get_irq(op, i);
+		irq = platform_get_irq_optional(op, i);
 		if ((nr_irq > 1) && (irq > 0))
 			ret = devm_request_irq(&op->dev, irq,
 					       pxad_chan_handler,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/qcom/bam_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/qcom/bam_dma.c
@@ -515,14 +515,6 @@
 	return 0;
 }
 
-static int bam_pm_runtime_get_sync(struct device *dev)
-{
-	if (pm_runtime_enabled(dev))
-		return pm_runtime_get_sync(dev);
-
-	return 0;
-}
-
 /**
  * bam_free_chan - Frees dma resources associated with specific channel
  * @chan: specified channel
@@ -538,7 +530,7 @@
 	unsigned long flags;
 	int ret;
 
-	ret = bam_pm_runtime_get_sync(bdev->dev);
+	ret = pm_runtime_get_sync(bdev->dev);
 	if (ret < 0)
 		return;
 
@@ -734,7 +726,7 @@
 	unsigned long flag;
 	int ret;
 
-	ret = bam_pm_runtime_get_sync(bdev->dev);
+	ret = pm_runtime_get_sync(bdev->dev);
 	if (ret < 0)
 		return ret;
 
@@ -760,7 +752,7 @@
 	unsigned long flag;
 	int ret;
 
-	ret = bam_pm_runtime_get_sync(bdev->dev);
+	ret = pm_runtime_get_sync(bdev->dev);
 	if (ret < 0)
 		return ret;
 
@@ -869,7 +861,7 @@
 	if (srcs & P_IRQ)
 		tasklet_schedule(&bdev->task);
 
-	ret = bam_pm_runtime_get_sync(bdev->dev);
+	ret = pm_runtime_get_sync(bdev->dev);
 	if (ret < 0)
 		return IRQ_NONE;
 
@@ -987,7 +979,7 @@
 	if (!vd)
 		return;
 
-	ret = bam_pm_runtime_get_sync(bdev->dev);
+	ret = pm_runtime_get_sync(bdev->dev);
 	if (ret < 0)
 		return;
 
@@ -1350,11 +1342,6 @@
 	if (ret)
 		goto err_unregister_dma;
 
-	if (!bdev->bamclk) {
-		pm_runtime_disable(&pdev->dev);
-		return 0;
-	}
-
 	pm_runtime_irq_safe(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, BAM_DMA_AUTOSUSPEND_DELAY);
 	pm_runtime_use_autosuspend(&pdev->dev);
@@ -1438,10 +1425,8 @@
 {
 	struct bam_device *bdev = dev_get_drvdata(dev);
 
-	if (bdev->bamclk) {
-		pm_runtime_force_suspend(dev);
-		clk_unprepare(bdev->bamclk);
-	}
+	pm_runtime_force_suspend(dev);
+	clk_unprepare(bdev->bamclk);
 
 	return 0;
 }
@@ -1451,13 +1436,11 @@
 	struct bam_device *bdev = dev_get_drvdata(dev);
 	int ret;
 
-	if (bdev->bamclk) {
-		ret = clk_prepare(bdev->bamclk);
-		if (ret)
-			return ret;
+	ret = clk_prepare(bdev->bamclk);
+	if (ret)
+		return ret;
 
-		pm_runtime_force_resume(dev);
-	}
+	pm_runtime_force_resume(dev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/qcom/gpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/qcom/gpi.c
@@ -1961,7 +1961,6 @@
 error_config_int:
 	gpi_free_ring(&gpii->ev_ring, gpii);
 exit_gpi_init:
-	mutex_unlock(&gpii->ctrl_lock);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/sf-pdma/sf-pdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/sf-pdma/sf-pdma.c
@@ -52,16 +52,6 @@
 static struct sf_pdma_desc *sf_pdma_alloc_desc(struct sf_pdma_chan *chan)
 {
 	struct sf_pdma_desc *desc;
-	unsigned long flags;
-
-	spin_lock_irqsave(&chan->lock, flags);
-
-	if (chan->desc && !chan->desc->in_use) {
-		spin_unlock_irqrestore(&chan->lock, flags);
-		return chan->desc;
-	}
-
-	spin_unlock_irqrestore(&chan->lock, flags);
 
 	desc = kzalloc(sizeof(*desc), GFP_NOWAIT);
 	if (!desc)
@@ -106,12 +96,10 @@
 	if (!desc)
 		return NULL;
 
-	desc->in_use = true;
 	desc->dirn = DMA_MEM_TO_MEM;
 	desc->async_tx = vchan_tx_prep(&chan->vchan, &desc->vdesc, flags);
 
 	spin_lock_irqsave(&chan->vchan.lock, iflags);
-	chan->desc = desc;
 	sf_pdma_fill_desc(desc, dest, src, len);
 	spin_unlock_irqrestore(&chan->vchan.lock, iflags);
 
@@ -170,11 +158,17 @@
 	unsigned long flags;
 	u64 residue = 0;
 	struct sf_pdma_desc *desc;
-	struct dma_async_tx_descriptor *tx;
+	struct dma_async_tx_descriptor *tx = NULL;
 
 	spin_lock_irqsave(&chan->vchan.lock, flags);
 
-	tx = &chan->desc->vdesc.tx;
+	list_for_each_entry(vd, &chan->vchan.desc_submitted, node)
+		if (vd->tx.cookie == cookie)
+			tx = &vd->tx;
+
+	if (!tx)
+		goto out;
+
 	if (cookie == tx->chan->completed_cookie)
 		goto out;
 
@@ -241,6 +235,19 @@
 	writel(v, regs->ctrl);
 }
 
+static struct sf_pdma_desc *sf_pdma_get_first_pending_desc(struct sf_pdma_chan *chan)
+{
+	struct virt_dma_chan *vchan = &chan->vchan;
+	struct virt_dma_desc *vdesc;
+
+	if (list_empty(&vchan->desc_issued))
+		return NULL;
+
+	vdesc = list_first_entry(&vchan->desc_issued, struct virt_dma_desc, node);
+
+	return container_of(vdesc, struct sf_pdma_desc, vdesc);
+}
+
 static void sf_pdma_xfer_desc(struct sf_pdma_chan *chan)
 {
 	struct sf_pdma_desc *desc = chan->desc;
@@ -268,8 +275,11 @@
 
 	spin_lock_irqsave(&chan->vchan.lock, flags);
 
-	if (vchan_issue_pending(&chan->vchan) && chan->desc)
+	if (!chan->desc && vchan_issue_pending(&chan->vchan)) {
+		/* vchan_issue_pending has made a check that desc in not NULL */
+		chan->desc = sf_pdma_get_first_pending_desc(chan);
 		sf_pdma_xfer_desc(chan);
+	}
 
 	spin_unlock_irqrestore(&chan->vchan.lock, flags);
 }
@@ -279,7 +289,7 @@
 	struct sf_pdma_desc *desc;
 
 	desc = to_sf_pdma_desc(vdesc);
-	desc->in_use = false;
+	kfree(desc);
 }
 
 static void sf_pdma_donebh_tasklet(struct tasklet_struct *t)
@@ -298,6 +308,11 @@
 	spin_lock_irqsave(&chan->vchan.lock, flags);
 	list_del(&chan->desc->vdesc.node);
 	vchan_cookie_complete(&chan->desc->vdesc);
+
+	chan->desc = sf_pdma_get_first_pending_desc(chan);
+	if (chan->desc)
+		sf_pdma_xfer_desc(chan);
+
 	spin_unlock_irqrestore(&chan->vchan.lock, flags);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/sf-pdma/sf-pdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/sf-pdma/sf-pdma.h
@@ -82,7 +82,6 @@
 	u64				src_addr;
 	struct virt_dma_desc		vdesc;
 	struct sf_pdma_chan		*chan;
-	bool				in_use;
 	enum dma_transfer_direction	dirn;
 	struct dma_async_tx_descriptor *async_tx;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/sh/rcar-dmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/sh/rcar-dmac.c
@@ -1868,8 +1868,13 @@
 
 	dmac->dev = &pdev->dev;
 	platform_set_drvdata(pdev, dmac);
-	dma_set_max_seg_size(dmac->dev, RCAR_DMATCR_MASK);
-	dma_set_mask_and_coherent(dmac->dev, DMA_BIT_MASK(40));
+	ret = dma_set_max_seg_size(dmac->dev, RCAR_DMATCR_MASK);
+	if (ret)
+		return ret;
+
+	ret = dma_set_mask_and_coherent(dmac->dev, DMA_BIT_MASK(40));
+	if (ret)
+		return ret;
 
 	ret = rcar_dmac_parse_of(&pdev->dev, dmac);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/sh/rz-dmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/sh/rz-dmac.c
@@ -9,6 +9,7 @@
  * Copyright 2012 Javier Martin, Vista Silicon <javier.martin@vista-silicon.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/interrupt.h>
@@ -143,8 +144,8 @@
 #define CHCFG_REQD			BIT(3)
 #define CHCFG_SEL(bits)			((bits) & 0x07)
 #define CHCFG_MEM_COPY			(0x80400008)
-#define CHCFG_FILL_DDS(a)		(((a) << 16) & GENMASK(19, 16))
-#define CHCFG_FILL_SDS(a)		(((a) << 12) & GENMASK(15, 12))
+#define CHCFG_FILL_DDS_MASK		GENMASK(19, 16)
+#define CHCFG_FILL_SDS_MASK		GENMASK(15, 12)
 #define CHCFG_FILL_TM(a)		(((a) & BIT(5)) << 22)
 #define CHCFG_FILL_AM(a)		(((a) & GENMASK(4, 2)) << 6)
 #define CHCFG_FILL_LVL(a)		(((a) & BIT(1)) << 5)
@@ -607,13 +608,15 @@
 	if (val == CHCFG_DS_INVALID)
 		return -EINVAL;
 
-	channel->chcfg |= CHCFG_FILL_DDS(val);
+	channel->chcfg &= ~CHCFG_FILL_DDS_MASK;
+	channel->chcfg |= FIELD_PREP(CHCFG_FILL_DDS_MASK, val);
 
 	val = rz_dmac_ds_to_val_mapping(config->src_addr_width);
 	if (val == CHCFG_DS_INVALID)
 		return -EINVAL;
 
-	channel->chcfg |= CHCFG_FILL_SDS(val);
+	channel->chcfg &= ~CHCFG_FILL_SDS_MASK;
+	channel->chcfg |= FIELD_PREP(CHCFG_FILL_SDS_MASK, val);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/sh/shdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/sh/shdma.h
@@ -25,7 +25,7 @@
 	const struct sh_dmae_slave_config *config; /* Slave DMA configuration */
 	int xmit_shift;			/* log_2(bytes_per_xfer) */
 	void __iomem *base;
-	char dev_id[16];		/* unique name per DMAC of channel */
+	char dev_id[32];		/* unique name per DMAC of channel */
 	int pm_error;
 	dma_addr_t slave_addr;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/sprd-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/sprd-dma.c
@@ -1236,11 +1236,8 @@
 {
 	struct sprd_dma_dev *sdev = platform_get_drvdata(pdev);
 	struct sprd_dma_chn *c, *cn;
-	int ret;
 
-	ret = pm_runtime_get_sync(&pdev->dev);
-	if (ret < 0)
-		return ret;
+	pm_runtime_get_sync(&pdev->dev);
 
 	/* explicitly free the irq */
 	if (sdev->irq > 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/st_fdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/st_fdma.c
@@ -874,4 +874,4 @@
 MODULE_DESCRIPTION("STMicroelectronics FDMA engine driver");
 MODULE_AUTHOR("Ludovic.barre <Ludovic.barre@st.com>");
 MODULE_AUTHOR("Peter Griffin <peter.griffin@linaro.org>");
-MODULE_ALIAS("platform: " DRIVER_NAME);
+MODULE_ALIAS("platform:" DRIVER_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ste_dma40.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ste_dma40.c
@@ -3597,6 +3597,10 @@
 	spin_lock_init(&base->lcla_pool.lock);
 
 	base->irq = platform_get_irq(pdev, 0);
+	if (base->irq < 0) {
+		ret = base->irq;
+		goto destroy_cache;
+	}
 
 	ret = request_irq(base->irq, d40_handle_interrupt, 0, D40_NAME, base);
 	if (ret) {
@@ -3693,6 +3697,7 @@
 		regulator_disable(base->lcpa_regulator);
 		regulator_put(base->lcpa_regulator);
 	}
+	pm_runtime_disable(base->dev);
 
 	kfree(base->lcla_pool.alloc_map);
 	kfree(base->lookup_log_chans);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/stm32-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/stm32-dma.c
@@ -270,7 +270,6 @@
 						       u32 threshold)
 {
 	enum dma_slave_buswidth max_width;
-	u64 addr = buf_addr;
 
 	if (threshold == STM32_DMA_FIFO_THRESHOLD_FULL)
 		max_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
@@ -281,7 +280,7 @@
 	       max_width > DMA_SLAVE_BUSWIDTH_1_BYTE)
 		max_width = max_width >> 1;
 
-	if (do_div(addr, max_width))
+	if (buf_addr & (max_width - 1))
 		max_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 
 	return max_width;
@@ -753,8 +752,14 @@
 		if (src_bus_width < 0)
 			return src_bus_width;
 
-		/* Set memory burst size */
-		src_maxburst = STM32_DMA_MAX_BURST;
+		/*
+		 * Set memory burst size - burst not possible if address is not aligned on
+		 * the address boundary equal to the size of the transfer
+		 */
+		if (buf_addr & (buf_len - 1))
+			src_maxburst = 1;
+		else
+			src_maxburst = STM32_DMA_MAX_BURST;
 		src_best_burst = stm32_dma_get_best_burst(buf_len,
 							  src_maxburst,
 							  fifoth,
@@ -803,8 +808,14 @@
 		if (dst_bus_width < 0)
 			return dst_bus_width;
 
-		/* Set memory burst size */
-		dst_maxburst = STM32_DMA_MAX_BURST;
+		/*
+		 * Set memory burst size - burst not possible if address is not aligned on
+		 * the address boundary equal to the size of the transfer
+		 */
+		if (buf_addr & (buf_len - 1))
+			dst_maxburst = 1;
+		else
+			dst_maxburst = STM32_DMA_MAX_BURST;
 		dst_best_burst = stm32_dma_get_best_burst(buf_len,
 							  dst_maxburst,
 							  fifoth,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/stm32-dmamux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/stm32-dmamux.c
@@ -292,10 +292,12 @@
 	ret = of_dma_router_register(node, stm32_dmamux_route_allocate,
 				     &stm32_dmamux->dmarouter);
 	if (ret)
-		goto err_clk;
+		goto pm_disable;
 
 	return 0;
 
+pm_disable:
+	pm_runtime_disable(&pdev->dev);
 err_clk:
 	clk_disable_unprepare(stm32_dmamux->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/stm32-mdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/stm32-mdma.c
@@ -40,7 +40,6 @@
 					 STM32_MDMA_SHIFT(mask))
 
 #define STM32_MDMA_GISR0		0x0000 /* MDMA Int Status Reg 1 */
-#define STM32_MDMA_GISR1		0x0004 /* MDMA Int Status Reg 2 */
 
 /* MDMA Channel x interrupt/status register */
 #define STM32_MDMA_CISR(x)		(0x40 + 0x40 * (x)) /* x = 0..62 */
@@ -184,7 +183,7 @@
 #define STM32_MDMA_CTBR(x)		(0x68 + 0x40 * (x))
 #define STM32_MDMA_CTBR_DBUS		BIT(17)
 #define STM32_MDMA_CTBR_SBUS		BIT(16)
-#define STM32_MDMA_CTBR_TSEL_MASK	GENMASK(7, 0)
+#define STM32_MDMA_CTBR_TSEL_MASK	GENMASK(5, 0)
 #define STM32_MDMA_CTBR_TSEL(n)		STM32_MDMA_SET(n, \
 						      STM32_MDMA_CTBR_TSEL_MASK)
 
@@ -196,7 +195,7 @@
 
 #define STM32_MDMA_MAX_BUF_LEN		128
 #define STM32_MDMA_MAX_BLOCK_LEN	65536
-#define STM32_MDMA_MAX_CHANNELS		63
+#define STM32_MDMA_MAX_CHANNELS		32
 #define STM32_MDMA_MAX_REQUESTS		256
 #define STM32_MDMA_MAX_BURST		128
 #define STM32_MDMA_VERY_HIGH_PRIORITY	0x3
@@ -510,7 +509,7 @@
 	src_maxburst = chan->dma_config.src_maxburst;
 	dst_maxburst = chan->dma_config.dst_maxburst;
 
-	ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id));
+	ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id)) & ~STM32_MDMA_CCR_EN;
 	ctcr = stm32_mdma_read(dmadev, STM32_MDMA_CTCR(chan->id));
 	ctbr = stm32_mdma_read(dmadev, STM32_MDMA_CTBR(chan->id));
 
@@ -938,7 +937,7 @@
 	if (!desc)
 		return NULL;
 
-	ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id));
+	ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id)) & ~STM32_MDMA_CCR_EN;
 	ctcr = stm32_mdma_read(dmadev, STM32_MDMA_CTCR(chan->id));
 	ctbr = stm32_mdma_read(dmadev, STM32_MDMA_CTBR(chan->id));
 	cbndtr = stm32_mdma_read(dmadev, STM32_MDMA_CBNDTR(chan->id));
@@ -1207,6 +1206,10 @@
 	unsigned long flags;
 	u32 status, reg;
 
+	/* Transfer can be terminated */
+	if (!chan->desc || (stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id)) & STM32_MDMA_CCR_EN))
+		return -EPERM;
+
 	hwdesc = chan->desc->node[chan->curr_hwdesc].hwdesc;
 
 	spin_lock_irqsave(&chan->vchan.lock, flags);
@@ -1345,26 +1348,16 @@
 static irqreturn_t stm32_mdma_irq_handler(int irq, void *devid)
 {
 	struct stm32_mdma_device *dmadev = devid;
-	struct stm32_mdma_chan *chan = devid;
+	struct stm32_mdma_chan *chan;
 	u32 reg, id, ccr, ien, status;
 
 	/* Find out which channel generates the interrupt */
 	status = readl_relaxed(dmadev->base + STM32_MDMA_GISR0);
-	if (status) {
-		id = __ffs(status);
-	} else {
-		status = readl_relaxed(dmadev->base + STM32_MDMA_GISR1);
-		if (!status) {
-			dev_dbg(mdma2dev(dmadev), "spurious it\n");
-			return IRQ_NONE;
-		}
-		id = __ffs(status);
-		/*
-		 * As GISR0 provides status for channel id from 0 to 31,
-		 * so GISR1 provides status for channel id from 32 to 62
-		 */
-		id += 32;
+	if (!status) {
+		dev_dbg(mdma2dev(dmadev), "spurious it\n");
+		return IRQ_NONE;
 	}
+	id = __ffs(status);
 
 	chan = &dmadev->chan[id];
 	if (!chan) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/tegra210-adma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/tegra210-adma.c
@@ -224,7 +224,7 @@
 	int ret;
 
 	/* Clear any interrupts */
-	tdma_write(tdma, tdma->cdata->global_int_clear, 0x1);
+	tdma_write(tdma, tdma->cdata->ch_base_offset + tdma->cdata->global_int_clear, 0x1);
 
 	/* Assert soft reset */
 	tdma_write(tdma, ADMA_GLOBAL_SOFT_RESET, 0x1);
@@ -867,7 +867,7 @@
 
 	pm_runtime_enable(&pdev->dev);
 
-	ret = pm_runtime_get_sync(&pdev->dev);
+	ret = pm_runtime_resume_and_get(&pdev->dev);
 	if (ret < 0)
 		goto rpm_disable;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ti/dma-crossbar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ti/dma-crossbar.c
@@ -245,6 +245,7 @@
 	if (dma_spec->args[0] >= xbar->xbar_requests) {
 		dev_err(&pdev->dev, "Invalid XBAR request number: %d\n",
 			dma_spec->args[0]);
+		put_device(&pdev->dev);
 		return ERR_PTR(-EINVAL);
 	}
 
@@ -252,12 +253,14 @@
 	dma_spec->np = of_parse_phandle(ofdma->of_node, "dma-masters", 0);
 	if (!dma_spec->np) {
 		dev_err(&pdev->dev, "Can't get DMA master\n");
+		put_device(&pdev->dev);
 		return ERR_PTR(-EINVAL);
 	}
 
 	map = kzalloc(sizeof(*map), GFP_KERNEL);
 	if (!map) {
 		of_node_put(dma_spec->np);
+		put_device(&pdev->dev);
 		return ERR_PTR(-ENOMEM);
 	}
 
@@ -268,6 +271,8 @@
 		mutex_unlock(&xbar->mutex);
 		dev_err(&pdev->dev, "Run out of free DMA requests\n");
 		kfree(map);
+		of_node_put(dma_spec->np);
+		put_device(&pdev->dev);
 		return ERR_PTR(-ENOMEM);
 	}
 	set_bit(map->xbar_out, xbar->dma_inuse);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ti/edma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ti/edma.c
@@ -217,7 +217,6 @@
 struct edma_cc;
 
 struct edma_tc {
-	struct device_node		*node;
 	u16				id;
 };
 
@@ -2459,9 +2458,14 @@
 	if (irq < 0 && node)
 		irq = irq_of_parse_and_map(node, 0);
 
-	if (irq >= 0) {
+	if (irq > 0) {
 		irq_name = devm_kasprintf(dev, GFP_KERNEL, "%s_ccint",
 					  dev_name(dev));
+		if (!irq_name) {
+			ret = -ENOMEM;
+			goto err_disable_pm;
+		}
+
 		ret = devm_request_irq(dev, irq, dma_irq_handler, 0, irq_name,
 				       ecc);
 		if (ret) {
@@ -2475,9 +2479,14 @@
 	if (irq < 0 && node)
 		irq = irq_of_parse_and_map(node, 2);
 
-	if (irq >= 0) {
+	if (irq > 0) {
 		irq_name = devm_kasprintf(dev, GFP_KERNEL, "%s_ccerrint",
 					  dev_name(dev));
+		if (!irq_name) {
+			ret = -ENOMEM;
+			goto err_disable_pm;
+		}
+
 		ret = devm_request_irq(dev, irq, dma_ccerr_handler, 0, irq_name,
 				       ecc);
 		if (ret) {
@@ -2514,13 +2523,13 @@
 			if (ret || i == ecc->num_tc)
 				break;
 
-			ecc->tc_list[i].node = tc_args.np;
 			ecc->tc_list[i].id = i;
 			queue_priority_mapping[i][1] = tc_args.args[0];
 			if (queue_priority_mapping[i][1] > lowest_priority) {
 				lowest_priority = queue_priority_mapping[i][1];
 				info->default_queue = i;
 			}
+			of_node_put(tc_args.np);
 		}
 
 		/* See if we have optional dma-channel-mask array */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ti/k3-udma-glue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ti/k3-udma-glue.c
@@ -299,6 +299,7 @@
 	ret = device_register(&tx_chn->common.chan_dev);
 	if (ret) {
 		dev_err(dev, "Channel Device registration failed %d\n", ret);
+		put_device(&tx_chn->common.chan_dev);
 		tx_chn->common.chan_dev.parent = NULL;
 		goto err;
 	}
@@ -917,6 +918,7 @@
 	ret = device_register(&rx_chn->common.chan_dev);
 	if (ret) {
 		dev_err(dev, "Channel Device registration failed %d\n", ret);
+		put_device(&rx_chn->common.chan_dev);
 		rx_chn->common.chan_dev.parent = NULL;
 		goto err;
 	}
@@ -1048,6 +1050,7 @@
 	ret = device_register(&rx_chn->common.chan_dev);
 	if (ret) {
 		dev_err(dev, "Channel Device registration failed %d\n", ret);
+		put_device(&rx_chn->common.chan_dev);
 		rx_chn->common.chan_dev.parent = NULL;
 		goto err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ti/k3-udma-private.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ti/k3-udma-private.c
@@ -31,14 +31,14 @@
 	}
 
 	pdev = of_find_device_by_node(udma_node);
+	if (np != udma_node)
+		of_node_put(udma_node);
+
 	if (!pdev) {
 		pr_debug("UDMA device not found\n");
 		return ERR_PTR(-EPROBE_DEFER);
 	}
 
-	if (np != udma_node)
-		of_node_put(udma_node);
-
 	ud = platform_get_drvdata(pdev);
 	if (!ud) {
 		pr_debug("UDMA has not been probed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/ti/k3-udma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/ti/k3-udma.c
@@ -300,8 +300,6 @@
 
 	struct udma_tx_drain tx_drain;
 
-	u32 bcnt; /* number of bytes completed since the start of the channel */
-
 	/* Channel configuration parameters */
 	struct udma_chan_config config;
 
@@ -757,6 +755,21 @@
 	}
 }
 
+static void udma_decrement_byte_counters(struct udma_chan *uc, u32 val)
+{
+	if (uc->desc->dir == DMA_DEV_TO_MEM) {
+		udma_rchanrt_write(uc, UDMA_CHAN_RT_BCNT_REG, val);
+		udma_rchanrt_write(uc, UDMA_CHAN_RT_SBCNT_REG, val);
+		if (uc->config.ep_type != PSIL_EP_NATIVE)
+			udma_rchanrt_write(uc, UDMA_CHAN_RT_PEER_BCNT_REG, val);
+	} else {
+		udma_tchanrt_write(uc, UDMA_CHAN_RT_BCNT_REG, val);
+		udma_tchanrt_write(uc, UDMA_CHAN_RT_SBCNT_REG, val);
+		if (!uc->bchan && uc->config.ep_type != PSIL_EP_NATIVE)
+			udma_tchanrt_write(uc, UDMA_CHAN_RT_PEER_BCNT_REG, val);
+	}
+}
+
 static void udma_reset_counters(struct udma_chan *uc)
 {
 	u32 val;
@@ -790,8 +803,6 @@
 		val = udma_rchanrt_read(uc, UDMA_CHAN_RT_PEER_BCNT_REG);
 		udma_rchanrt_write(uc, UDMA_CHAN_RT_PEER_BCNT_REG, val);
 	}
-
-	uc->bcnt = 0;
 }
 
 static int udma_reset_chan(struct udma_chan *uc, bool hard)
@@ -1115,7 +1126,7 @@
 		if (uc->desc) {
 			struct udma_desc *d = uc->desc;
 
-			uc->bcnt += d->residue;
+			udma_decrement_byte_counters(uc, d->residue);
 			udma_start(uc);
 			vchan_cookie_complete(&d->vd);
 			break;
@@ -1168,7 +1179,7 @@
 				vchan_cyclic_callback(&d->vd);
 			} else {
 				if (udma_is_desc_really_done(uc, d)) {
-					uc->bcnt += d->residue;
+					udma_decrement_byte_counters(uc, d->residue);
 					udma_start(uc);
 					vchan_cookie_complete(&d->vd);
 				} else {
@@ -1204,7 +1215,7 @@
 			vchan_cyclic_callback(&d->vd);
 		} else {
 			/* TODO: figure out the real amount of data */
-			uc->bcnt += d->residue;
+			udma_decrement_byte_counters(uc, d->residue);
 			udma_start(uc);
 			vchan_cookie_complete(&d->vd);
 		}
@@ -1348,6 +1359,7 @@
 {
 	struct udma_dev *ud = uc->ud;
 	enum udma_tp_level tpl;
+	int ret;
 
 	if (uc->bchan) {
 		dev_dbg(ud->dev, "chan%d: already have bchan%d allocated\n",
@@ -1365,8 +1377,11 @@
 		tpl = ud->bchan_tpl.levels - 1;
 
 	uc->bchan = __udma_reserve_bchan(ud, tpl, -1);
-	if (IS_ERR(uc->bchan))
-		return PTR_ERR(uc->bchan);
+	if (IS_ERR(uc->bchan)) {
+		ret = PTR_ERR(uc->bchan);
+		uc->bchan = NULL;
+		return ret;
+	}
 
 	uc->tchan = uc->bchan;
 
@@ -1376,6 +1391,7 @@
 static int udma_get_tchan(struct udma_chan *uc)
 {
 	struct udma_dev *ud = uc->ud;
+	int ret;
 
 	if (uc->tchan) {
 		dev_dbg(ud->dev, "chan%d: already have tchan%d allocated\n",
@@ -1390,8 +1406,11 @@
 	 */
 	uc->tchan = __udma_reserve_tchan(ud, uc->config.channel_tpl,
 					 uc->config.mapped_channel_id);
-	if (IS_ERR(uc->tchan))
-		return PTR_ERR(uc->tchan);
+	if (IS_ERR(uc->tchan)) {
+		ret = PTR_ERR(uc->tchan);
+		uc->tchan = NULL;
+		return ret;
+	}
 
 	if (ud->tflow_cnt) {
 		int tflow_id;
@@ -1421,6 +1440,7 @@
 static int udma_get_rchan(struct udma_chan *uc)
 {
 	struct udma_dev *ud = uc->ud;
+	int ret;
 
 	if (uc->rchan) {
 		dev_dbg(ud->dev, "chan%d: already have rchan%d allocated\n",
@@ -1435,8 +1455,13 @@
 	 */
 	uc->rchan = __udma_reserve_rchan(ud, uc->config.channel_tpl,
 					 uc->config.mapped_channel_id);
+	if (IS_ERR(uc->rchan)) {
+		ret = PTR_ERR(uc->rchan);
+		uc->rchan = NULL;
+		return ret;
+	}
 
-	return PTR_ERR_OR_ZERO(uc->rchan);
+	return 0;
 }
 
 static int udma_get_chan_pair(struct udma_chan *uc)
@@ -1490,6 +1515,7 @@
 static int udma_get_rflow(struct udma_chan *uc, int flow_id)
 {
 	struct udma_dev *ud = uc->ud;
+	int ret;
 
 	if (!uc->rchan) {
 		dev_err(ud->dev, "chan%d: does not have rchan??\n", uc->id);
@@ -1503,8 +1529,13 @@
 	}
 
 	uc->rflow = __udma_get_rflow(ud, flow_id);
+	if (IS_ERR(uc->rflow)) {
+		ret = PTR_ERR(uc->rflow);
+		uc->rflow = NULL;
+		return ret;
+	}
 
-	return PTR_ERR_OR_ZERO(uc->rflow);
+	return 0;
 }
 
 static void bcdma_put_bchan(struct udma_chan *uc)
@@ -3791,7 +3822,6 @@
 			bcnt = udma_tchanrt_read(uc, UDMA_CHAN_RT_BCNT_REG);
 		}
 
-		bcnt -= uc->bcnt;
 		if (bcnt && !(bcnt % uc->desc->residue))
 			residue = 0;
 		else
@@ -3927,6 +3957,7 @@
 {
 	struct udma_chan *uc = to_udma_chan(&vc->chan);
 	struct udma_desc *d;
+	u8 status;
 
 	if (!vd)
 		return;
@@ -3936,12 +3967,12 @@
 	if (d->metadata_size)
 		udma_fetch_epib(uc, d);
 
-	/* Provide residue information for the client */
 	if (result) {
 		void *desc_vaddr = udma_curr_cppi5_desc_vaddr(d, d->desc_idx);
 
 		if (cppi5_desc_get_type(desc_vaddr) ==
 		    CPPI5_INFO0_DESC_TYPE_VAL_HOST) {
+			/* Provide residue information for the client */
 			result->residue = d->residue -
 					  cppi5_hdesc_get_pktlen(desc_vaddr);
 			if (result->residue)
@@ -3950,7 +3981,12 @@
 				result->result = DMA_TRANS_NOERROR;
 		} else {
 			result->residue = 0;
-			result->result = DMA_TRANS_NOERROR;
+			/* Propagate TR Response errors to the client */
+			status = d->hwdesc[0].tr_resp_base->status;
+			if (status)
+				result->result = DMA_TRANS_ABORTED;
+			else
+				result->result = DMA_TRANS_NOERROR;
 		}
 	}
 }
@@ -4379,7 +4415,9 @@
 		ud->rchan_cnt = UDMA_CAP2_RCHAN_CNT(cap2);
 		break;
 	case DMA_TYPE_BCDMA:
-		ud->bchan_cnt = BCDMA_CAP2_BCHAN_CNT(cap2);
+		ud->bchan_cnt = BCDMA_CAP2_BCHAN_CNT(cap2) +
+				BCDMA_CAP3_HBCHAN_CNT(cap3) +
+				BCDMA_CAP3_UBCHAN_CNT(cap3);
 		ud->tchan_cnt = BCDMA_CAP2_TCHAN_CNT(cap2);
 		ud->rchan_cnt = BCDMA_CAP2_RCHAN_CNT(cap2);
 		ud->rflow_cnt = ud->rchan_cnt;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/uniphier-xdmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/uniphier-xdmac.c
@@ -131,8 +131,9 @@
 static void uniphier_xdmac_chan_start(struct uniphier_xdmac_chan *xc,
 				      struct uniphier_xdmac_desc *xd)
 {
-	u32 src_mode, src_addr, src_width;
-	u32 dst_mode, dst_addr, dst_width;
+	u32 src_mode, src_width;
+	u32 dst_mode, dst_width;
+	dma_addr_t src_addr, dst_addr;
 	u32 val, its, tnum;
 	enum dma_slave_buswidth buswidth;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/Makefile
@@ -1,4 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_XILINX_DMATEST) += axidmatest.o
+obj-$(CONFIG_XILINX_VDMATEST) += vdmatest.o
 obj-$(CONFIG_XILINX_DMA) += xilinx_dma.o
 obj-$(CONFIG_XILINX_ZYNQMP_DMA) += zynqmp_dma.o
 obj-$(CONFIG_XILINX_ZYNQMP_DPDMA) += xilinx_dpdma.o
+obj-$(CONFIG_XILINX_FRMBUF) += xilinx_frmbuf.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/axidmatest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/axidmatest.c
@@ -0,0 +1,698 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * XILINX AXI DMA and MCDMA Engine test module
+ *
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ *
+ * Based on Atmel DMA Test Client
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/init.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/of_dma.h>
+#include <linux/platform_device.h>
+#include <linux/random.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+#include <linux/sched/task.h>
+#include <linux/dma/xilinx_dma.h>
+
+static unsigned int test_buf_size = 16384;
+module_param(test_buf_size, uint, 0444);
+MODULE_PARM_DESC(test_buf_size, "Size of the memcpy test buffer");
+
+static unsigned int iterations = 5;
+module_param(iterations, uint, 0444);
+MODULE_PARM_DESC(iterations,
+		 "Iterations before stopping test (default: infinite)");
+
+/*
+ * Initialization patterns. All bytes in the source buffer has bit 7
+ * set, all bytes in the destination buffer has bit 7 cleared.
+ *
+ * Bit 6 is set for all bytes which are to be copied by the DMA
+ * engine. Bit 5 is set for all bytes which are to be overwritten by
+ * the DMA engine.
+ *
+ * The remaining bits are the inverse of a counter which increments by
+ * one for each byte address.
+ */
+#define PATTERN_SRC		0x80
+#define PATTERN_DST		0x00
+#define PATTERN_COPY		0x40
+#define PATTERN_OVERWRITE	0x20
+#define PATTERN_COUNT_MASK	0x1f
+
+#define XILINX_DMATEST_BD_CNT	11
+
+struct dmatest_slave_thread {
+	struct list_head node;
+	struct task_struct *task;
+	struct dma_chan *tx_chan;
+	struct dma_chan *rx_chan;
+	u8 **srcs;
+	u8 **dsts;
+	enum dma_transaction_type type;
+	bool done;
+};
+
+struct dmatest_chan {
+	struct list_head node;
+	struct dma_chan *chan;
+	struct list_head threads;
+};
+
+/*
+ * These are protected by dma_list_mutex since they're only used by
+ * the DMA filter function callback
+ */
+static DECLARE_WAIT_QUEUE_HEAD(thread_wait);
+static LIST_HEAD(dmatest_channels);
+static unsigned int nr_channels;
+
+static unsigned long long dmatest_persec(s64 runtime, unsigned int val)
+{
+	unsigned long long per_sec = 1000000;
+
+	if (runtime <= 0)
+		return 0;
+
+	/* drop precision until runtime is 32-bits */
+	while (runtime > UINT_MAX) {
+		runtime >>= 1;
+		per_sec <<= 1;
+	}
+
+	per_sec *= val;
+	do_div(per_sec, runtime);
+	return per_sec;
+}
+
+static unsigned long long dmatest_KBs(s64 runtime, unsigned long long len)
+{
+	return dmatest_persec(runtime, len >> 10);
+}
+
+static bool is_threaded_test_run(struct dmatest_chan *tx_dtc,
+				 struct dmatest_chan *rx_dtc)
+{
+	struct dmatest_slave_thread *thread;
+	int ret = false;
+
+	list_for_each_entry(thread, &tx_dtc->threads, node) {
+		if (!thread->done)
+			ret = true;
+	}
+
+	list_for_each_entry(thread, &rx_dtc->threads, node) {
+		if (!thread->done)
+			ret = true;
+	}
+	return ret;
+}
+
+static unsigned long dmatest_random(void)
+{
+	unsigned long buf;
+
+	get_random_bytes(&buf, sizeof(buf));
+	return buf;
+}
+
+static void dmatest_init_srcs(u8 **bufs, unsigned int start, unsigned int len)
+{
+	unsigned int i;
+	u8 *buf;
+
+	for (; (buf = *bufs); bufs++) {
+		for (i = 0; i < start; i++)
+			buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK);
+		for ( ; i < start + len; i++)
+			buf[i] = PATTERN_SRC | PATTERN_COPY
+				| (~i & PATTERN_COUNT_MASK);
+		for ( ; i < test_buf_size; i++)
+			buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK);
+	}
+}
+
+static void dmatest_init_dsts(u8 **bufs, unsigned int start, unsigned int len)
+{
+	unsigned int i;
+	u8 *buf;
+
+	for (; (buf = *bufs); bufs++) {
+		for (i = 0; i < start; i++)
+			buf[i] = PATTERN_DST | (~i & PATTERN_COUNT_MASK);
+		for ( ; i < start + len; i++)
+			buf[i] = PATTERN_DST | PATTERN_OVERWRITE
+				| (~i & PATTERN_COUNT_MASK);
+		for ( ; i < test_buf_size; i++)
+			buf[i] = PATTERN_DST | (~i & PATTERN_COUNT_MASK);
+	}
+}
+
+static void dmatest_mismatch(u8 actual, u8 pattern, unsigned int index,
+			     unsigned int counter, bool is_srcbuf)
+{
+	u8 diff = actual ^ pattern;
+	u8 expected = pattern | (~counter & PATTERN_COUNT_MASK);
+	const char *thread_name = current->comm;
+
+	if (is_srcbuf)
+		pr_warn("%s: srcbuf[0x%x] overwritten! Expected %02x, got %02x\n",
+			thread_name, index, expected, actual);
+	else if ((pattern & PATTERN_COPY) &&
+		 (diff & (PATTERN_COPY | PATTERN_OVERWRITE)))
+		pr_warn("%s: dstbuf[0x%x] not copied! Expected %02x, got %02x\n",
+			thread_name, index, expected, actual);
+	else if (diff & PATTERN_SRC)
+		pr_warn("%s: dstbuf[0x%x] was copied! Expected %02x, got %02x\n",
+			thread_name, index, expected, actual);
+	else
+		pr_warn("%s: dstbuf[0x%x] mismatch! Expected %02x, got %02x\n",
+			thread_name, index, expected, actual);
+}
+
+static unsigned int dmatest_verify(u8 **bufs, unsigned int start,
+				   unsigned int end, unsigned int counter,
+				   u8 pattern, bool is_srcbuf)
+{
+	unsigned int i;
+	unsigned int error_count = 0;
+	u8 actual;
+	u8 expected;
+	u8 *buf;
+	unsigned int counter_orig = counter;
+
+	for (; (buf = *bufs); bufs++) {
+		counter = counter_orig;
+		for (i = start; i < end; i++) {
+			actual = buf[i];
+			expected = pattern | (~counter & PATTERN_COUNT_MASK);
+			if (actual != expected) {
+				if (error_count < 32)
+					dmatest_mismatch(actual, pattern, i,
+							 counter, is_srcbuf);
+				error_count++;
+			}
+			counter++;
+		}
+	}
+
+	if (error_count > 32)
+		pr_warn("%s: %u errors suppressed\n",
+			current->comm, error_count - 32);
+
+	return error_count;
+}
+
+static void dmatest_slave_tx_callback(void *completion)
+{
+	complete(completion);
+}
+
+static void dmatest_slave_rx_callback(void *completion)
+{
+	complete(completion);
+}
+
+/* Function for slave transfers
+ * Each thread requires 2 channels, one for transmit, and one for receive
+ */
+static int dmatest_slave_func(void *data)
+{
+	struct dmatest_slave_thread	*thread = data;
+	struct dma_chan *tx_chan;
+	struct dma_chan *rx_chan;
+	const char *thread_name;
+	unsigned int src_off, dst_off, len;
+	unsigned int error_count;
+	unsigned int failed_tests = 0;
+	unsigned int total_tests = 0;
+	dma_cookie_t tx_cookie;
+	dma_cookie_t rx_cookie;
+	enum dma_status status;
+	enum dma_ctrl_flags flags;
+	int ret;
+	int src_cnt;
+	int dst_cnt;
+	int bd_cnt = XILINX_DMATEST_BD_CNT;
+	int i;
+
+	ktime_t	ktime, start, diff;
+	ktime_t	filltime = 0;
+	ktime_t	comparetime = 0;
+	s64 runtime = 0;
+	unsigned long long total_len = 0;
+	thread_name = current->comm;
+	ret = -ENOMEM;
+
+
+	/* Ensure that all previous reads are complete */
+	smp_rmb();
+	tx_chan = thread->tx_chan;
+	rx_chan = thread->rx_chan;
+	dst_cnt = bd_cnt;
+	src_cnt = bd_cnt;
+
+	thread->srcs = kcalloc(src_cnt + 1, sizeof(u8 *), GFP_KERNEL);
+	if (!thread->srcs)
+		goto err_srcs;
+	for (i = 0; i < src_cnt; i++) {
+		thread->srcs[i] = kmalloc(test_buf_size, GFP_KERNEL);
+		if (!thread->srcs[i])
+			goto err_srcbuf;
+	}
+	thread->srcs[i] = NULL;
+
+	thread->dsts = kcalloc(dst_cnt + 1, sizeof(u8 *), GFP_KERNEL);
+	if (!thread->dsts)
+		goto err_dsts;
+	for (i = 0; i < dst_cnt; i++) {
+		thread->dsts[i] = kmalloc(test_buf_size, GFP_KERNEL);
+		if (!thread->dsts[i])
+			goto err_dstbuf;
+	}
+	thread->dsts[i] = NULL;
+
+	set_user_nice(current, 10);
+
+	flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+
+	ktime = ktime_get();
+	while (!kthread_should_stop() &&
+	       !(iterations && total_tests >= iterations)) {
+		struct dma_device *tx_dev = tx_chan->device;
+		struct dma_device *rx_dev = rx_chan->device;
+		struct dma_async_tx_descriptor *txd = NULL;
+		struct dma_async_tx_descriptor *rxd = NULL;
+		dma_addr_t dma_srcs[XILINX_DMATEST_BD_CNT];
+		dma_addr_t dma_dsts[XILINX_DMATEST_BD_CNT];
+		struct completion rx_cmp;
+		struct completion tx_cmp;
+		unsigned long rx_tmo =
+				msecs_to_jiffies(300000); /* RX takes longer */
+		unsigned long tx_tmo = msecs_to_jiffies(30000);
+		u8 align = 0;
+		struct scatterlist tx_sg[XILINX_DMATEST_BD_CNT];
+		struct scatterlist rx_sg[XILINX_DMATEST_BD_CNT];
+
+		total_tests++;
+
+		/* honor larger alignment restrictions */
+		align = tx_dev->copy_align;
+		if (rx_dev->copy_align > align)
+			align = rx_dev->copy_align;
+
+		if (1 << align > test_buf_size) {
+			pr_err("%u-byte buffer too small for %d-byte alignment\n",
+			       test_buf_size, 1 << align);
+			break;
+		}
+
+		len = dmatest_random() % test_buf_size + 1;
+		len = (len >> align) << align;
+		if (!len)
+			len = 1 << align;
+		src_off = dmatest_random() % (test_buf_size - len + 1);
+		dst_off = dmatest_random() % (test_buf_size - len + 1);
+
+		src_off = (src_off >> align) << align;
+		dst_off = (dst_off >> align) << align;
+
+		start = ktime_get();
+		dmatest_init_srcs(thread->srcs, src_off, len);
+		dmatest_init_dsts(thread->dsts, dst_off, len);
+		diff = ktime_sub(ktime_get(), start);
+		filltime = ktime_add(filltime, diff);
+
+		for (i = 0; i < src_cnt; i++) {
+			u8 *buf = thread->srcs[i] + src_off;
+
+			dma_srcs[i] = dma_map_single(tx_dev->dev, buf, len,
+						     DMA_MEM_TO_DEV);
+		}
+
+		for (i = 0; i < dst_cnt; i++) {
+			dma_dsts[i] = dma_map_single(rx_dev->dev,
+						     thread->dsts[i],
+						     test_buf_size,
+						     DMA_BIDIRECTIONAL);
+		}
+
+		sg_init_table(tx_sg, bd_cnt);
+		sg_init_table(rx_sg, bd_cnt);
+
+		for (i = 0; i < bd_cnt; i++) {
+			sg_dma_address(&tx_sg[i]) = dma_srcs[i];
+			sg_dma_address(&rx_sg[i]) = dma_dsts[i] + dst_off;
+
+			sg_dma_len(&tx_sg[i]) = len;
+			sg_dma_len(&rx_sg[i]) = len;
+			total_len += len;
+		}
+
+		rxd = rx_dev->device_prep_slave_sg(rx_chan, rx_sg, bd_cnt,
+				DMA_DEV_TO_MEM, flags, NULL);
+
+		txd = tx_dev->device_prep_slave_sg(tx_chan, tx_sg, bd_cnt,
+				DMA_MEM_TO_DEV, flags, NULL);
+
+		if (!rxd || !txd) {
+			for (i = 0; i < src_cnt; i++)
+				dma_unmap_single(tx_dev->dev, dma_srcs[i], len,
+						 DMA_MEM_TO_DEV);
+			for (i = 0; i < dst_cnt; i++)
+				dma_unmap_single(rx_dev->dev, dma_dsts[i],
+						 test_buf_size,
+						 DMA_BIDIRECTIONAL);
+			pr_warn("%s: #%u: prep error with src_off=0x%x ",
+				thread_name, total_tests - 1, src_off);
+			pr_warn("dst_off=0x%x len=0x%x\n",
+				dst_off, len);
+			msleep(100);
+			failed_tests++;
+			continue;
+		}
+
+		init_completion(&rx_cmp);
+		rxd->callback = dmatest_slave_rx_callback;
+		rxd->callback_param = &rx_cmp;
+		rx_cookie = rxd->tx_submit(rxd);
+
+		init_completion(&tx_cmp);
+		txd->callback = dmatest_slave_tx_callback;
+		txd->callback_param = &tx_cmp;
+		tx_cookie = txd->tx_submit(txd);
+
+		if (dma_submit_error(rx_cookie) ||
+		    dma_submit_error(tx_cookie)) {
+			pr_warn("%s: #%u: submit error %d/%d with src_off=0x%x ",
+				thread_name, total_tests - 1,
+				rx_cookie, tx_cookie, src_off);
+			pr_warn("dst_off=0x%x len=0x%x\n",
+				dst_off, len);
+			msleep(100);
+			failed_tests++;
+			continue;
+		}
+		dma_async_issue_pending(rx_chan);
+		dma_async_issue_pending(tx_chan);
+
+		tx_tmo = wait_for_completion_timeout(&tx_cmp, tx_tmo);
+
+		status = dma_async_is_tx_complete(tx_chan, tx_cookie,
+						  NULL, NULL);
+
+		if (tx_tmo == 0) {
+			pr_warn("%s: #%u: tx test timed out\n",
+				thread_name, total_tests - 1);
+			failed_tests++;
+			continue;
+		} else if (status != DMA_COMPLETE) {
+			pr_warn("%s: #%u: tx got completion callback, ",
+				thread_name, total_tests - 1);
+			pr_warn("but status is \'%s\'\n",
+				status == DMA_ERROR ? "error" :
+				"in progress");
+			failed_tests++;
+			continue;
+		}
+
+		rx_tmo = wait_for_completion_timeout(&rx_cmp, rx_tmo);
+		status = dma_async_is_tx_complete(rx_chan, rx_cookie,
+						  NULL, NULL);
+
+		if (rx_tmo == 0) {
+			pr_warn("%s: #%u: rx test timed out\n",
+				thread_name, total_tests - 1);
+			failed_tests++;
+			continue;
+		} else if (status != DMA_COMPLETE) {
+			pr_warn("%s: #%u: rx got completion callback, ",
+				thread_name, total_tests - 1);
+			pr_warn("but status is \'%s\'\n",
+				status == DMA_ERROR ? "error" :
+				"in progress");
+			failed_tests++;
+			continue;
+		}
+
+		/* Unmap by myself */
+		for (i = 0; i < dst_cnt; i++)
+			dma_unmap_single(rx_dev->dev, dma_dsts[i],
+					 test_buf_size, DMA_BIDIRECTIONAL);
+
+		error_count = 0;
+		start = ktime_get();
+		pr_debug("%s: verifying source buffer...\n", thread_name);
+		error_count += dmatest_verify(thread->srcs, 0, src_off,
+				0, PATTERN_SRC, true);
+		error_count += dmatest_verify(thread->srcs, src_off,
+				src_off + len, src_off,
+				PATTERN_SRC | PATTERN_COPY, true);
+		error_count += dmatest_verify(thread->srcs, src_off + len,
+				test_buf_size, src_off + len,
+				PATTERN_SRC, true);
+
+		pr_debug("%s: verifying dest buffer...\n",
+			 thread->task->comm);
+		error_count += dmatest_verify(thread->dsts, 0, dst_off,
+				0, PATTERN_DST, false);
+		error_count += dmatest_verify(thread->dsts, dst_off,
+				dst_off + len, src_off,
+				PATTERN_SRC | PATTERN_COPY, false);
+		error_count += dmatest_verify(thread->dsts, dst_off + len,
+				test_buf_size, dst_off + len,
+				PATTERN_DST, false);
+		diff = ktime_sub(ktime_get(), start);
+		comparetime = ktime_add(comparetime, diff);
+
+		if (error_count) {
+			pr_warn("%s: #%u: %u errors with ",
+				thread_name, total_tests - 1, error_count);
+			pr_warn("src_off=0x%x dst_off=0x%x len=0x%x\n",
+				src_off, dst_off, len);
+			failed_tests++;
+		} else {
+			pr_debug("%s: #%u: No errors with ",
+				 thread_name, total_tests - 1);
+			pr_debug("src_off=0x%x dst_off=0x%x len=0x%x\n",
+				 src_off, dst_off, len);
+		}
+	}
+
+	ktime = ktime_sub(ktime_get(), ktime);
+	ktime = ktime_sub(ktime, comparetime);
+	ktime = ktime_sub(ktime, filltime);
+	runtime = ktime_to_us(ktime);
+
+	ret = 0;
+	for (i = 0; thread->dsts[i]; i++)
+		kfree(thread->dsts[i]);
+err_dstbuf:
+	kfree(thread->dsts);
+err_dsts:
+	for (i = 0; thread->srcs[i]; i++)
+		kfree(thread->srcs[i]);
+err_srcbuf:
+	kfree(thread->srcs);
+err_srcs:
+	pr_notice("%s: terminating after %u tests, %u failures %llu iops %llu KB/s (status %d)\n",
+		  thread_name, total_tests, failed_tests,
+		  dmatest_persec(runtime, total_tests),
+		  dmatest_KBs(runtime, total_len), ret);
+
+	thread->done = true;
+	wake_up(&thread_wait);
+
+	return ret;
+}
+
+static void dmatest_cleanup_channel(struct dmatest_chan *dtc)
+{
+	struct dmatest_slave_thread *thread;
+	struct dmatest_slave_thread *_thread;
+	int ret;
+
+	list_for_each_entry_safe(thread, _thread, &dtc->threads, node) {
+		ret = kthread_stop(thread->task);
+		pr_debug("dmatest: thread %s exited with status %d\n",
+			 thread->task->comm, ret);
+		list_del(&thread->node);
+		put_task_struct(thread->task);
+		kfree(thread);
+	}
+	kfree(dtc);
+}
+
+static int dmatest_add_slave_threads(struct dmatest_chan *tx_dtc,
+				     struct dmatest_chan *rx_dtc)
+{
+	struct dmatest_slave_thread *thread;
+	struct dma_chan *tx_chan = tx_dtc->chan;
+	struct dma_chan *rx_chan = rx_dtc->chan;
+	int ret;
+
+	thread = kzalloc(sizeof(struct dmatest_slave_thread), GFP_KERNEL);
+	if (!thread) {
+		pr_warn("dmatest: No memory for slave thread %s-%s\n",
+			dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+	}
+
+	thread->tx_chan = tx_chan;
+	thread->rx_chan = rx_chan;
+	thread->type = (enum dma_transaction_type)DMA_SLAVE;
+
+	/* Ensure that all previous writes are complete */
+	smp_wmb();
+	thread->task = kthread_run(dmatest_slave_func, thread, "%s-%s",
+				   dma_chan_name(tx_chan),
+				   dma_chan_name(rx_chan));
+	ret = PTR_ERR(thread->task);
+	if (IS_ERR(thread->task)) {
+		pr_warn("dmatest: Failed to run thread %s-%s\n",
+			dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+		kfree(thread);
+		return ret;
+	}
+
+	/* srcbuf and dstbuf are allocated by the thread itself */
+	get_task_struct(thread->task);
+	list_add_tail(&thread->node, &tx_dtc->threads);
+
+	/* Added one thread with 2 channels */
+	return 1;
+}
+
+static int dmatest_add_slave_channels(struct dma_chan *tx_chan,
+				      struct dma_chan *rx_chan)
+{
+	struct dmatest_chan *tx_dtc;
+	struct dmatest_chan *rx_dtc;
+	unsigned int thread_count = 0;
+
+	tx_dtc = kmalloc(sizeof(struct dmatest_chan), GFP_KERNEL);
+	if (!tx_dtc) {
+		pr_warn("dmatest: No memory for tx %s\n",
+			dma_chan_name(tx_chan));
+		return -ENOMEM;
+	}
+
+	rx_dtc = kmalloc(sizeof(struct dmatest_chan), GFP_KERNEL);
+	if (!rx_dtc) {
+		pr_warn("dmatest: No memory for rx %s\n",
+			dma_chan_name(rx_chan));
+		return -ENOMEM;
+	}
+
+	tx_dtc->chan = tx_chan;
+	rx_dtc->chan = rx_chan;
+	INIT_LIST_HEAD(&tx_dtc->threads);
+	INIT_LIST_HEAD(&rx_dtc->threads);
+
+	dmatest_add_slave_threads(tx_dtc, rx_dtc);
+	thread_count += 1;
+
+	pr_info("dmatest: Started %u threads using %s %s\n",
+		thread_count, dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+
+	list_add_tail(&tx_dtc->node, &dmatest_channels);
+	list_add_tail(&rx_dtc->node, &dmatest_channels);
+	nr_channels += 2;
+
+	if (iterations)
+		wait_event(thread_wait, !is_threaded_test_run(tx_dtc, rx_dtc));
+
+	return 0;
+}
+
+static int xilinx_axidmatest_probe(struct platform_device *pdev)
+{
+	struct dma_chan *chan, *rx_chan;
+	int err;
+
+	chan = dma_request_chan(&pdev->dev, "axidma0");
+	if (IS_ERR(chan)) {
+		err = PTR_ERR(chan);
+		if (err != -EPROBE_DEFER)
+			pr_err("xilinx_dmatest: No Tx channel\n");
+		return err;
+	}
+
+	rx_chan = dma_request_chan(&pdev->dev, "axidma1");
+	if (IS_ERR(rx_chan)) {
+		err = PTR_ERR(rx_chan);
+		if (err != -EPROBE_DEFER)
+			pr_err("xilinx_dmatest: No Rx channel\n");
+		goto free_tx;
+	}
+
+	err = dmatest_add_slave_channels(chan, rx_chan);
+	if (err) {
+		pr_err("xilinx_dmatest: Unable to add channels\n");
+		goto free_rx;
+	}
+
+	return 0;
+
+free_rx:
+	dma_release_channel(rx_chan);
+free_tx:
+	dma_release_channel(chan);
+
+	return err;
+}
+
+static int xilinx_axidmatest_remove(struct platform_device *pdev)
+{
+	struct dmatest_chan *dtc, *_dtc;
+	struct dma_chan *chan;
+
+	list_for_each_entry_safe(dtc, _dtc, &dmatest_channels, node) {
+		list_del(&dtc->node);
+		chan = dtc->chan;
+		dmatest_cleanup_channel(dtc);
+		pr_info("xilinx_dmatest: dropped channel %s\n",
+			dma_chan_name(chan));
+		dmaengine_terminate_all(chan);
+		dma_release_channel(chan);
+	}
+	return 0;
+}
+
+static const struct of_device_id xilinx_axidmatest_of_ids[] = {
+	{ .compatible = "xlnx,axi-dma-test-1.00.a",},
+	{}
+};
+
+static struct platform_driver xilinx_axidmatest_driver = {
+	.driver = {
+		.name = "xilinx_axidmatest",
+		.of_match_table = xilinx_axidmatest_of_ids,
+	},
+	.probe = xilinx_axidmatest_probe,
+	.remove = xilinx_axidmatest_remove,
+};
+
+static int __init axidma_init(void)
+{
+	return platform_driver_register(&xilinx_axidmatest_driver);
+}
+late_initcall(axidma_init);
+
+static void __exit axidma_exit(void)
+{
+	platform_driver_unregister(&xilinx_axidmatest_driver);
+}
+module_exit(axidma_exit)
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx AXI DMA Test Client");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/vdmatest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/vdmatest.c
@@ -0,0 +1,666 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * XILINX VDMA Engine test client driver
+ *
+ * Copyright (C) 2010-2014 Xilinx, Inc. All rights reserved.
+ *
+ * Based on Atmel DMA Test Client
+ *
+ * Description:
+ * This is a simple Xilinx VDMA test client for AXI VDMA driver.
+ * This test assumes both the channels of VDMA are enabled in the
+ * hardware design and configured in back-to-back connection. Test
+ * starts by pumping the data onto one channel (MM2S) and then
+ * compares the data that is received on the other channel (S2MM).
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/dma/xilinx_dma.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/of_dma.h>
+#include <linux/platform_device.h>
+#include <linux/random.h>
+#include <linux/slab.h>
+#include <linux/sched/task.h>
+#include <linux/wait.h>
+
+static unsigned int test_buf_size = 64;
+module_param(test_buf_size, uint, 0444);
+MODULE_PARM_DESC(test_buf_size, "Size of the memcpy test buffer");
+
+static unsigned int iterations = 1;
+module_param(iterations, uint, 0444);
+MODULE_PARM_DESC(iterations,
+		"Iterations before stopping test (default: infinite)");
+
+static unsigned int hsize = 64;
+module_param(hsize, uint, 0444);
+MODULE_PARM_DESC(hsize, "Horizontal size in bytes");
+
+static unsigned int vsize = 32;
+module_param(vsize, uint, 0444);
+MODULE_PARM_DESC(vsize, "Vertical size in bytes");
+
+/*
+ * Initialization patterns. All bytes in the source buffer has bit 7
+ * set, all bytes in the destination buffer has bit 7 cleared.
+ *
+ * Bit 6 is set for all bytes which are to be copied by the DMA
+ * engine. Bit 5 is set for all bytes which are to be overwritten by
+ * the DMA engine.
+ *
+ * The remaining bits are the inverse of a counter which increments by
+ * one for each byte address.
+ */
+#define PATTERN_SRC		0x80
+#define PATTERN_DST		0x00
+#define PATTERN_COPY		0x40
+#define PATTERN_OVERWRITE	0x20
+#define PATTERN_COUNT_MASK	0x1f
+
+/* Maximum number of frame buffers */
+#define MAX_NUM_FRAMES	32
+
+/**
+ * struct vdmatest_slave_thread - VDMA test thread
+ * @node: Thread node
+ * @task: Task structure pointer
+ * @tx_chan: Tx channel pointer
+ * @rx_chan: Rx Channel pointer
+ * @srcs: Source buffer
+ * @dsts: Destination buffer
+ * @type: DMA transaction type
+ */
+struct xilinx_vdmatest_slave_thread {
+	struct list_head node;
+	struct task_struct *task;
+	struct dma_chan *tx_chan;
+	struct dma_chan *rx_chan;
+	u8 **srcs;
+	u8 **dsts;
+	enum dma_transaction_type type;
+	bool done;
+};
+
+/**
+ * struct vdmatest_chan - VDMA Test channel
+ * @node: Channel node
+ * @chan: DMA channel pointer
+ * @threads: List of VDMA test threads
+ */
+struct xilinx_vdmatest_chan {
+	struct list_head node;
+	struct dma_chan *chan;
+	struct list_head threads;
+};
+
+/* Global variables */
+static DECLARE_WAIT_QUEUE_HEAD(thread_wait);
+static LIST_HEAD(xilinx_vdmatest_channels);
+static unsigned int nr_channels;
+static unsigned int frm_cnt;
+static dma_addr_t dma_srcs[MAX_NUM_FRAMES];
+static dma_addr_t dma_dsts[MAX_NUM_FRAMES];
+static struct dma_interleaved_template xt;
+
+static bool is_threaded_test_run(struct xilinx_vdmatest_chan *tx_dtc,
+					struct xilinx_vdmatest_chan *rx_dtc)
+{
+	struct xilinx_vdmatest_slave_thread *thread;
+	int ret = false;
+
+	list_for_each_entry(thread, &tx_dtc->threads, node) {
+		if (!thread->done)
+			ret = true;
+	}
+
+	list_for_each_entry(thread, &rx_dtc->threads, node) {
+		if (!thread->done)
+			ret = true;
+	}
+	return ret;
+}
+
+static void xilinx_vdmatest_init_srcs(u8 **bufs, unsigned int start,
+					unsigned int len)
+{
+	unsigned int i;
+	u8 *buf;
+
+	for (; (buf = *bufs); bufs++) {
+		for (i = 0; i < start; i++)
+			buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK);
+		for (; i < start + len; i++)
+			buf[i] = PATTERN_SRC | PATTERN_COPY
+				| (~i & PATTERN_COUNT_MASK);
+		for (; i < test_buf_size; i++)
+			buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK);
+		buf++;
+	}
+}
+
+static void xilinx_vdmatest_init_dsts(u8 **bufs, unsigned int start,
+					unsigned int len)
+{
+	unsigned int i;
+	u8 *buf;
+
+	for (; (buf = *bufs); bufs++) {
+		for (i = 0; i < start; i++)
+			buf[i] = PATTERN_DST | (~i & PATTERN_COUNT_MASK);
+		for (; i < start + len; i++)
+			buf[i] = PATTERN_DST | PATTERN_OVERWRITE
+				| (~i & PATTERN_COUNT_MASK);
+		for (; i < test_buf_size; i++)
+			buf[i] = PATTERN_DST | (~i & PATTERN_COUNT_MASK);
+	}
+}
+
+static void xilinx_vdmatest_mismatch(u8 actual, u8 pattern, unsigned int index,
+		unsigned int counter, bool is_srcbuf)
+{
+	u8 diff = actual ^ pattern;
+	u8 expected = pattern | (~counter & PATTERN_COUNT_MASK);
+	const char *thread_name = current->comm;
+
+	if (is_srcbuf)
+		pr_warn(
+		"%s: srcbuf[0x%x] overwritten! Expected %02x, got %02x\n",
+				thread_name, index, expected, actual);
+	else if ((pattern & PATTERN_COPY)
+			&& (diff & (PATTERN_COPY | PATTERN_OVERWRITE)))
+		pr_warn(
+		"%s: dstbuf[0x%x] not copied! Expected %02x, got %02x\n",
+				thread_name, index, expected, actual);
+	else if (diff & PATTERN_SRC)
+		pr_warn(
+		"%s: dstbuf[0x%x] was copied! Expected %02x, got %02x\n",
+				thread_name, index, expected, actual);
+	else
+		pr_warn(
+		"%s: dstbuf[0x%x] mismatch! Expected %02x, got %02x\n",
+				thread_name, index, expected, actual);
+}
+
+static unsigned int xilinx_vdmatest_verify(u8 **bufs, unsigned int start,
+		unsigned int end, unsigned int counter, u8 pattern,
+		bool is_srcbuf)
+{
+	unsigned int i, error_count = 0;
+	u8 actual, expected, *buf;
+	unsigned int counter_orig = counter;
+
+	for (; (buf = *bufs); bufs++) {
+		counter = counter_orig;
+		for (i = start; i < end; i++) {
+			actual = buf[i];
+			expected = pattern | (~counter & PATTERN_COUNT_MASK);
+			if (actual != expected) {
+				if (error_count < 32)
+					xilinx_vdmatest_mismatch(actual,
+							pattern, i,
+							counter, is_srcbuf);
+				error_count++;
+			}
+			counter++;
+		}
+	}
+
+	if (error_count > 32)
+		pr_warn("%s: %u errors suppressed\n",
+			current->comm, error_count - 32);
+
+	return error_count;
+}
+
+static void xilinx_vdmatest_slave_tx_callback(void *completion)
+{
+	pr_debug("Got tx callback\n");
+	complete(completion);
+}
+
+static void xilinx_vdmatest_slave_rx_callback(void *completion)
+{
+	pr_debug("Got rx callback\n");
+	complete(completion);
+}
+
+/*
+ * Function for slave transfers
+ * Each thread requires 2 channels, one for transmit, and one for receive
+ */
+static int xilinx_vdmatest_slave_func(void *data)
+{
+	struct xilinx_vdmatest_slave_thread *thread = data;
+	struct dma_chan *tx_chan, *rx_chan;
+	const char *thread_name;
+	unsigned int len, error_count;
+	unsigned int failed_tests = 0, total_tests = 0;
+	dma_cookie_t tx_cookie = 0, rx_cookie = 0;
+	enum dma_status status;
+	enum dma_ctrl_flags flags;
+	int ret = -ENOMEM, i;
+	struct xilinx_vdma_config config;
+
+	thread_name = current->comm;
+
+	/* Limit testing scope here */
+	test_buf_size = hsize * vsize;
+
+	/* This barrier ensures 'thread' is initialized and
+	 * we get valid DMA channels
+	 */
+	smp_rmb();
+	tx_chan = thread->tx_chan;
+	rx_chan = thread->rx_chan;
+
+	thread->srcs = kcalloc(frm_cnt+1, sizeof(u8 *), GFP_KERNEL);
+	if (!thread->srcs)
+		goto err_srcs;
+	for (i = 0; i < frm_cnt; i++) {
+		thread->srcs[i] = kmalloc(test_buf_size, GFP_KERNEL);
+		if (!thread->srcs[i])
+			goto err_srcbuf;
+	}
+
+	thread->dsts = kcalloc(frm_cnt+1, sizeof(u8 *), GFP_KERNEL);
+	if (!thread->dsts)
+		goto err_dsts;
+	for (i = 0; i < frm_cnt; i++) {
+		thread->dsts[i] = kmalloc(test_buf_size, GFP_KERNEL);
+		if (!thread->dsts[i])
+			goto err_dstbuf;
+	}
+
+	set_user_nice(current, 10);
+
+	flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+
+	while (!kthread_should_stop()
+		&& !(iterations && total_tests >= iterations)) {
+		struct dma_device *tx_dev = tx_chan->device;
+		struct dma_device *rx_dev = rx_chan->device;
+		struct dma_async_tx_descriptor *txd = NULL;
+		struct dma_async_tx_descriptor *rxd = NULL;
+		struct completion rx_cmp, tx_cmp;
+		unsigned long rx_tmo =
+				msecs_to_jiffies(30000); /* RX takes longer */
+		unsigned long tx_tmo = msecs_to_jiffies(30000);
+		u8 align = 0;
+
+		total_tests++;
+
+		/* honor larger alignment restrictions */
+		align = tx_dev->copy_align;
+		if (rx_dev->copy_align > align)
+			align = rx_dev->copy_align;
+
+		if (1 << align > test_buf_size) {
+			pr_err("%u-byte buffer too small for %d-byte alignment\n",
+			       test_buf_size, 1 << align);
+			break;
+		}
+
+		len = test_buf_size;
+		xilinx_vdmatest_init_srcs(thread->srcs, 0, len);
+		xilinx_vdmatest_init_dsts(thread->dsts, 0, len);
+
+		/* Zero out configuration */
+		memset(&config, 0, sizeof(struct xilinx_vdma_config));
+
+		/* Set up hardware configuration information */
+		config.frm_cnt_en = 1;
+		config.coalesc = frm_cnt * 10;
+		config.park = 1;
+		xilinx_vdma_channel_set_config(tx_chan, &config);
+
+		xilinx_vdma_channel_set_config(rx_chan, &config);
+
+		for (i = 0; i < frm_cnt; i++) {
+			dma_dsts[i] = dma_map_single(rx_dev->dev,
+							thread->dsts[i],
+							test_buf_size,
+							DMA_DEV_TO_MEM);
+
+			if (dma_mapping_error(rx_dev->dev, dma_dsts[i])) {
+				failed_tests++;
+				continue;
+			}
+			xt.dst_start = dma_dsts[i];
+			xt.dir = DMA_DEV_TO_MEM;
+			xt.numf = vsize;
+			xt.sgl[0].size = hsize;
+			xt.sgl[0].icg = 0;
+			xt.frame_size = 1;
+			rxd = rx_dev->device_prep_interleaved_dma(rx_chan,
+								  &xt, flags);
+			rx_cookie = rxd->tx_submit(rxd);
+		}
+
+		for (i = 0; i < frm_cnt; i++) {
+			u8 *buf = thread->srcs[i];
+
+			dma_srcs[i] = dma_map_single(tx_dev->dev, buf, len,
+							DMA_MEM_TO_DEV);
+
+			if (dma_mapping_error(tx_dev->dev, dma_srcs[i])) {
+				failed_tests++;
+				continue;
+			}
+			xt.src_start = dma_srcs[i];
+			xt.dir = DMA_MEM_TO_DEV;
+			xt.numf = vsize;
+			xt.sgl[0].size = hsize;
+			xt.sgl[0].icg = 0;
+			xt.frame_size = 1;
+			txd = tx_dev->device_prep_interleaved_dma(tx_chan,
+								  &xt, flags);
+			tx_cookie = txd->tx_submit(txd);
+		}
+
+		if (!rxd || !txd) {
+			for (i = 0; i < frm_cnt; i++)
+				dma_unmap_single(tx_dev->dev, dma_srcs[i], len,
+						DMA_MEM_TO_DEV);
+			for (i = 0; i < frm_cnt; i++)
+				dma_unmap_single(rx_dev->dev, dma_dsts[i],
+						test_buf_size,
+						DMA_DEV_TO_MEM);
+			pr_warn("%s: #%u: prep error with len=0x%x ",
+					thread_name, total_tests - 1, len);
+			msleep(100);
+			failed_tests++;
+			continue;
+		}
+
+		init_completion(&rx_cmp);
+		rxd->callback = xilinx_vdmatest_slave_rx_callback;
+		rxd->callback_param = &rx_cmp;
+
+		init_completion(&tx_cmp);
+		txd->callback = xilinx_vdmatest_slave_tx_callback;
+		txd->callback_param = &tx_cmp;
+
+		if (dma_submit_error(rx_cookie) ||
+				dma_submit_error(tx_cookie)) {
+			pr_warn("%s: #%u: submit error %d/%d with len=0x%x ",
+					thread_name, total_tests - 1,
+					rx_cookie, tx_cookie, len);
+			msleep(100);
+			failed_tests++;
+			continue;
+		}
+		dma_async_issue_pending(tx_chan);
+		dma_async_issue_pending(rx_chan);
+
+		tx_tmo = wait_for_completion_timeout(&tx_cmp, tx_tmo);
+
+		status = dma_async_is_tx_complete(tx_chan, tx_cookie,
+							NULL, NULL);
+
+		if (tx_tmo == 0) {
+			pr_warn("%s: #%u: tx test timed out\n",
+					thread_name, total_tests - 1);
+			failed_tests++;
+			continue;
+		} else if (status != DMA_COMPLETE) {
+			pr_warn(
+			"%s: #%u: tx got completion callback, ",
+				   thread_name, total_tests - 1);
+			pr_warn("but status is \'%s\'\n",
+				   status == DMA_ERROR ? "error" :
+							"in progress");
+			failed_tests++;
+			continue;
+		}
+
+		rx_tmo = wait_for_completion_timeout(&rx_cmp, rx_tmo);
+		status = dma_async_is_tx_complete(rx_chan, rx_cookie,
+							NULL, NULL);
+
+		if (rx_tmo == 0) {
+			pr_warn("%s: #%u: rx test timed out\n",
+					thread_name, total_tests - 1);
+			failed_tests++;
+			continue;
+		} else if (status != DMA_COMPLETE) {
+			pr_warn(
+			"%s: #%u: rx got completion callback, ",
+					thread_name, total_tests - 1);
+			pr_warn("but status is \'%s\'\n",
+					status == DMA_ERROR ? "error" :
+							"in progress");
+			failed_tests++;
+			continue;
+		}
+
+		/* Unmap by myself */
+		for (i = 0; i < frm_cnt; i++)
+			dma_unmap_single(rx_dev->dev, dma_dsts[i],
+					 test_buf_size, DMA_DEV_TO_MEM);
+
+		error_count = 0;
+
+		pr_debug("%s: verifying source buffer...\n", thread_name);
+		error_count += xilinx_vdmatest_verify(thread->srcs, 0, 0,
+				0, PATTERN_SRC, true);
+		error_count += xilinx_vdmatest_verify(thread->srcs, 0,
+				len, 0, PATTERN_SRC | PATTERN_COPY, true);
+		error_count += xilinx_vdmatest_verify(thread->srcs, len,
+				test_buf_size, len, PATTERN_SRC, true);
+
+		pr_debug("%s: verifying dest buffer...\n",
+				thread->task->comm);
+		error_count += xilinx_vdmatest_verify(thread->dsts, 0, 0,
+				0, PATTERN_DST, false);
+		error_count += xilinx_vdmatest_verify(thread->dsts, 0,
+				len, 0, PATTERN_SRC | PATTERN_COPY, false);
+		error_count += xilinx_vdmatest_verify(thread->dsts, len,
+				test_buf_size, len, PATTERN_DST, false);
+
+		if (error_count) {
+			pr_warn("%s: #%u: %u errors with len=0x%x\n",
+				thread_name, total_tests - 1, error_count, len);
+			failed_tests++;
+		} else {
+			pr_debug("%s: #%u: No errors with len=0x%x\n",
+				thread_name, total_tests - 1, len);
+		}
+	}
+
+	ret = 0;
+	for (i = 0; thread->dsts[i]; i++)
+		kfree(thread->dsts[i]);
+err_dstbuf:
+	kfree(thread->dsts);
+err_dsts:
+	for (i = 0; thread->srcs[i]; i++)
+		kfree(thread->srcs[i]);
+err_srcbuf:
+	kfree(thread->srcs);
+err_srcs:
+	pr_notice("%s: terminating after %u tests, %u failures (status %d)\n",
+			thread_name, total_tests, failed_tests, ret);
+
+	thread->done = true;
+	wake_up(&thread_wait);
+
+	return ret;
+}
+
+static void xilinx_vdmatest_cleanup_channel(struct xilinx_vdmatest_chan *dtc)
+{
+	struct xilinx_vdmatest_slave_thread *thread, *_thread;
+	int ret;
+
+	list_for_each_entry_safe(thread, _thread,
+				&dtc->threads, node) {
+		ret = kthread_stop(thread->task);
+		pr_info("xilinx_vdmatest: thread %s exited with status %d\n",
+				thread->task->comm, ret);
+		list_del(&thread->node);
+		put_task_struct(thread->task);
+		kfree(thread);
+	}
+	kfree(dtc);
+}
+
+static int
+xilinx_vdmatest_add_slave_threads(struct xilinx_vdmatest_chan *tx_dtc,
+					struct xilinx_vdmatest_chan *rx_dtc)
+{
+	struct xilinx_vdmatest_slave_thread *thread;
+	struct dma_chan *tx_chan = tx_dtc->chan;
+	struct dma_chan *rx_chan = rx_dtc->chan;
+
+	thread = kzalloc(sizeof(struct xilinx_vdmatest_slave_thread),
+			GFP_KERNEL);
+	if (!thread)
+		pr_warn("xilinx_vdmatest: No memory for slave thread %s-%s\n",
+			   dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+
+	thread->tx_chan = tx_chan;
+	thread->rx_chan = rx_chan;
+	thread->type = (enum dma_transaction_type)DMA_SLAVE;
+
+	/* This barrier ensures the DMA channels in the 'thread'
+	 * are initialized
+	 */
+	smp_wmb();
+	thread->task = kthread_run(xilinx_vdmatest_slave_func, thread, "%s-%s",
+		dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+	if (IS_ERR(thread->task)) {
+		pr_warn("xilinx_vdmatest: Failed to run thread %s-%s\n",
+				dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+		kfree(thread);
+		return PTR_ERR(thread->task);
+	}
+
+	get_task_struct(thread->task);
+	list_add_tail(&thread->node, &tx_dtc->threads);
+
+	/* Added one thread with 2 channels */
+	return 1;
+}
+
+static int xilinx_vdmatest_add_slave_channels(struct dma_chan *tx_chan,
+					struct dma_chan *rx_chan)
+{
+	struct xilinx_vdmatest_chan *tx_dtc, *rx_dtc;
+	unsigned int thread_count = 0;
+
+	tx_dtc = kmalloc(sizeof(struct xilinx_vdmatest_chan), GFP_KERNEL);
+	if (!tx_dtc)
+		return -ENOMEM;
+
+	rx_dtc = kmalloc(sizeof(struct xilinx_vdmatest_chan), GFP_KERNEL);
+	if (!rx_dtc)
+		return -ENOMEM;
+
+	tx_dtc->chan = tx_chan;
+	rx_dtc->chan = rx_chan;
+	INIT_LIST_HEAD(&tx_dtc->threads);
+	INIT_LIST_HEAD(&rx_dtc->threads);
+
+	xilinx_vdmatest_add_slave_threads(tx_dtc, rx_dtc);
+	thread_count += 1;
+
+	pr_info("xilinx_vdmatest: Started %u threads using %s %s\n",
+		thread_count, dma_chan_name(tx_chan), dma_chan_name(rx_chan));
+
+	list_add_tail(&tx_dtc->node, &xilinx_vdmatest_channels);
+	list_add_tail(&rx_dtc->node, &xilinx_vdmatest_channels);
+	nr_channels += 2;
+
+	if (iterations)
+		wait_event(thread_wait, !is_threaded_test_run(tx_dtc, rx_dtc));
+
+	return 0;
+}
+
+static int xilinx_vdmatest_probe(struct platform_device *pdev)
+{
+	struct dma_chan *chan, *rx_chan;
+	int err;
+
+	err = of_property_read_u32(pdev->dev.of_node,
+					"xlnx,num-fstores", &frm_cnt);
+	if (err < 0) {
+		pr_err("xilinx_vdmatest: missing xlnx,num-fstores property\n");
+		return err;
+	}
+
+	chan = dma_request_chan(&pdev->dev, "vdma0");
+	if (IS_ERR(chan)) {
+		err = PTR_ERR(chan);
+		if (err != -EPROBE_DEFER)
+			pr_err("xilinx_vdmatest: No Tx channel\n");
+		return err;
+	}
+
+	rx_chan = dma_request_chan(&pdev->dev, "vdma1");
+	if (IS_ERR(rx_chan)) {
+		err = PTR_ERR(rx_chan);
+		if (err != -EPROBE_DEFER)
+			pr_err("xilinx_vdmatest: No Rx channel\n");
+		goto free_tx;
+	}
+
+	err = xilinx_vdmatest_add_slave_channels(chan, rx_chan);
+	if (err) {
+		pr_err("xilinx_vdmatest: Unable to add channels\n");
+		goto free_rx;
+	}
+	return 0;
+
+free_rx:
+	dma_release_channel(rx_chan);
+free_tx:
+	dma_release_channel(chan);
+
+	return err;
+}
+
+static int xilinx_vdmatest_remove(struct platform_device *pdev)
+{
+	struct xilinx_vdmatest_chan *dtc, *_dtc;
+	struct dma_chan *chan;
+
+	list_for_each_entry_safe(dtc, _dtc, &xilinx_vdmatest_channels, node) {
+		list_del(&dtc->node);
+		chan = dtc->chan;
+		xilinx_vdmatest_cleanup_channel(dtc);
+		pr_info("xilinx_vdmatest: dropped channel %s\n",
+			dma_chan_name(chan));
+		dmaengine_terminate_async(chan);
+		dma_release_channel(chan);
+	}
+	return 0;
+}
+
+static const struct of_device_id xilinx_vdmatest_of_ids[] = {
+	{ .compatible = "xlnx,axi-vdma-test-1.00.a",},
+	{}
+};
+
+static struct platform_driver xilinx_vdmatest_driver = {
+	.driver = {
+		.name = "xilinx_vdmatest",
+		.owner = THIS_MODULE,
+		.of_match_table = xilinx_vdmatest_of_ids,
+	},
+	.probe = xilinx_vdmatest_probe,
+	.remove = xilinx_vdmatest_remove,
+};
+
+module_platform_driver(xilinx_vdmatest_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx AXI VDMA Test Client");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/xilinx_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/xilinx_dma.c
@@ -792,7 +792,7 @@
 }
 
 /**
- * xilinx_dma_tx_descriptor - Allocate transaction descriptor
+ * xilinx_dma_alloc_tx_descriptor - Allocate transaction descriptor
  * @chan: Driver specific DMA channel
  *
  * Return: The allocated descriptor on success and NULL on failure.
@@ -2483,7 +2483,7 @@
 }
 
 /**
- * xilinx_dma_channel_set_config - Configure VDMA channel
+ * xilinx_vdma_channel_set_config - Configure VDMA channel
  * Run-time configuration for Axi VDMA, supports:
  * . halt the channel
  * . configure interrupt coalescing and inter-packet delay threshold
@@ -2862,7 +2862,9 @@
 	}
 
 	/* Request the interrupt */
-	chan->irq = irq_of_parse_and_map(node, chan->tdest);
+	chan->irq = of_irq_get(node, chan->tdest);
+	if (chan->irq < 0)
+		return dev_err_probe(xdev->dev, chan->irq, "failed to get irq\n");
 	err = request_irq(chan->irq, xdev->dma_config->irq_handler,
 			  IRQF_SHARED, "xilinx-dma-controller", chan);
 	if (err) {
@@ -2924,7 +2926,7 @@
  * @xdev: Driver specific device structure
  * @node: Device node
  *
- * Return: 0 always.
+ * Return: '0' on success and failure value on error.
  */
 static int xilinx_dma_child_probe(struct xilinx_dma_device *xdev,
 				    struct device_node *node)
@@ -2936,8 +2938,11 @@
 	if (xdev->dma_config->dmatype == XDMA_TYPE_AXIMCDMA && ret < 0)
 		dev_warn(xdev->dev, "missing dma-channels property\n");
 
-	for (i = 0; i < nr_channels; i++)
-		xilinx_dma_chan_probe(xdev, node);
+	for (i = 0; i < nr_channels; i++) {
+		ret = xilinx_dma_chan_probe(xdev, node);
+		if (ret)
+			return ret;
+	}
 
 	return 0;
 }
@@ -3037,9 +3042,10 @@
 
 	/* Request and map I/O memory */
 	xdev->regs = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(xdev->regs))
-		return PTR_ERR(xdev->regs);
-
+	if (IS_ERR(xdev->regs)) {
+		err = PTR_ERR(xdev->regs);
+		goto disable_clks;
+	}
 	/* Retrieve the DMA engine properties from the device tree */
 	xdev->max_buffer_len = GENMASK(XILINX_DMA_MAX_TRANS_LEN_MAX - 1, 0);
 	xdev->s2mm_chan_id = xdev->dma_config->max_channels / 2;
@@ -3067,7 +3073,7 @@
 		if (err < 0) {
 			dev_err(xdev->dev,
 				"missing xlnx,num-fstores property\n");
-			return err;
+			goto disable_clks;
 		}
 
 		err = of_property_read_u32(node, "xlnx,flush-fsync",
@@ -3087,7 +3093,11 @@
 		xdev->ext_addr = false;
 
 	/* Set the dma mask bits */
-	dma_set_mask_and_coherent(xdev->dev, DMA_BIT_MASK(addr_width));
+	err = dma_set_mask_and_coherent(xdev->dev, DMA_BIT_MASK(addr_width));
+	if (err < 0) {
+		dev_err(xdev->dev, "DMA mask error %d\n", err);
+		goto disable_clks;
+	}
 
 	/* Initialize the DMA engine */
 	xdev->common.dev = &pdev->dev;
@@ -3133,8 +3143,10 @@
 	/* Initialize the channels */
 	for_each_child_of_node(node, child) {
 		err = xilinx_dma_child_probe(xdev, child);
-		if (err < 0)
-			goto disable_clks;
+		if (err < 0) {
+			of_node_put(child);
+			goto error;
+		}
 	}
 
 	if (xdev->dma_config->dmatype == XDMA_TYPE_VDMA) {
@@ -3169,12 +3181,12 @@
 
 	return 0;
 
-disable_clks:
-	xdma_disable_allclks(xdev);
 error:
 	for (i = 0; i < xdev->dma_config->max_channels; i++)
 		if (xdev->chan[i])
 			xilinx_dma_chan_remove(xdev->chan[i]);
+disable_clks:
+	xdma_disable_allclks(xdev);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/xilinx_dpdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/xilinx_dpdma.c
@@ -213,7 +213,8 @@
  * @running: true if the channel is running
  * @first_frame: flag for the first frame of stream
  * @video_group: flag if multi-channel operation is needed for video channels
- * @lock: lock to access struct xilinx_dpdma_chan
+ * @lock: lock to access struct xilinx_dpdma_chan. Must be taken before
+ *        @vchan.lock, if both are to be held.
  * @desc_pool: descriptor allocation pool
  * @err_task: error IRQ bottom half handler
  * @desc: References to descriptors being processed
@@ -271,9 +272,6 @@
 /* -----------------------------------------------------------------------------
  * DebugFS
  */
-
-#ifdef CONFIG_DEBUG_FS
-
 #define XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE	32
 #define XILINX_DPDMA_DEBUGFS_UINT16_MAX_STR	"65535"
 
@@ -299,7 +297,7 @@
 
 static void xilinx_dpdma_debugfs_desc_done_irq(struct xilinx_dpdma_chan *chan)
 {
-	if (chan->id == dpdma_debugfs.chan_id)
+	if (IS_ENABLED(CONFIG_DEBUG_FS) && chan->id == dpdma_debugfs.chan_id)
 		dpdma_debugfs.xilinx_dpdma_irq_done_count++;
 }
 
@@ -462,16 +460,6 @@
 		dev_err(xdev->dev, "Failed to create debugfs testcase file\n");
 }
 
-#else
-static void xilinx_dpdma_debugfs_init(struct xilinx_dpdma_device *xdev)
-{
-}
-
-static void xilinx_dpdma_debugfs_desc_done_irq(struct xilinx_dpdma_chan *chan)
-{
-}
-#endif /* CONFIG_DEBUG_FS */
-
 /* -----------------------------------------------------------------------------
  * I/O Accessors
  */
@@ -682,6 +670,84 @@
 }
 
 /**
+ * xilinx_dpdma_chan_prep_cyclic - Prepare a cyclic dma descriptor
+ * @chan: DPDMA channel
+ * @buf_addr: buffer address
+ * @buf_len: buffer length
+ * @period_len: number of periods
+ * @flags: tx flags argument passed in to prepare function
+ *
+ * Prepare a tx descriptor incudling internal software/hardware descriptors
+ * for the given cyclic transaction.
+ *
+ * Return: A dma async tx descriptor on success, or NULL.
+ */
+static struct dma_async_tx_descriptor *
+xilinx_dpdma_chan_prep_cyclic(struct xilinx_dpdma_chan *chan,
+			      dma_addr_t buf_addr, size_t buf_len,
+			      size_t period_len, unsigned long flags)
+{
+	struct xilinx_dpdma_tx_desc *tx_desc;
+	struct xilinx_dpdma_sw_desc *sw_desc, *last = NULL;
+	unsigned int periods = buf_len / period_len;
+	unsigned int i;
+
+	tx_desc = xilinx_dpdma_chan_alloc_tx_desc(chan);
+	if (!tx_desc)
+		return (void *)tx_desc;
+
+	for (i = 0; i < periods; i++) {
+		struct xilinx_dpdma_hw_desc *hw_desc;
+
+		if (!IS_ALIGNED(buf_addr, XILINX_DPDMA_ALIGN_BYTES)) {
+			dev_err(chan->xdev->dev,
+				"buffer should be aligned at %d B\n",
+				XILINX_DPDMA_ALIGN_BYTES);
+			goto error;
+		}
+
+		sw_desc = xilinx_dpdma_chan_alloc_sw_desc(chan);
+		if (!sw_desc)
+			goto error;
+
+		xilinx_dpdma_sw_desc_set_dma_addrs(chan->xdev, sw_desc, last,
+						   &buf_addr, 1);
+		hw_desc = &sw_desc->hw;
+		hw_desc->xfer_size = period_len;
+		hw_desc->hsize_stride =
+			FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_HSIZE_MASK,
+				   period_len) |
+			FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_STRIDE_MASK,
+				   period_len);
+		hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_PREEMBLE;
+		hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_IGNORE_DONE;
+		hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_COMPLETE_INTR;
+
+		list_add_tail(&sw_desc->node, &tx_desc->descriptors);
+
+		buf_addr += period_len;
+		last = sw_desc;
+	}
+
+	sw_desc = list_first_entry(&tx_desc->descriptors,
+				   struct xilinx_dpdma_sw_desc, node);
+	last->hw.next_desc = lower_32_bits(sw_desc->dma_addr);
+	if (chan->xdev->ext_addr)
+		last->hw.addr_ext |=
+			FIELD_PREP(XILINX_DPDMA_DESC_ADDR_EXT_NEXT_ADDR_MASK,
+				   upper_32_bits(sw_desc->dma_addr));
+
+	last->hw.control |= XILINX_DPDMA_DESC_CONTROL_LAST_OF_FRAME;
+
+	return vchan_tx_prep(&chan->vchan, &tx_desc->vdesc, flags);
+
+error:
+	xilinx_dpdma_chan_free_tx_desc(&tx_desc->vdesc);
+
+	return NULL;
+}
+
+/**
  * xilinx_dpdma_chan_prep_interleaved_dma - Prepare an interleaved dma
  *					    descriptor
  * @chan: DPDMA channel
@@ -1109,12 +1175,14 @@
 	 * Complete the active descriptor, if any, promote the pending
 	 * descriptor to active, and queue the next transfer, if any.
 	 */
+	spin_lock(&chan->vchan.lock);
 	if (chan->desc.active)
 		vchan_cookie_complete(&chan->desc.active->vdesc);
 	chan->desc.active = pending;
 	chan->desc.pending = NULL;
 
 	xilinx_dpdma_chan_queue_transfer(chan);
+	spin_unlock(&chan->vchan.lock);
 
 out:
 	spin_unlock_irqrestore(&chan->lock, flags);
@@ -1200,6 +1268,23 @@
 /* -----------------------------------------------------------------------------
  * DMA Engine Operations
  */
+static struct dma_async_tx_descriptor *
+xilinx_dpdma_prep_dma_cyclic(struct dma_chan *dchan, dma_addr_t buf_addr,
+			     size_t buf_len, size_t period_len,
+			     enum dma_transfer_direction direction,
+			     unsigned long flags)
+{
+	struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan);
+
+	if (direction != DMA_MEM_TO_DEV)
+		return NULL;
+
+	if (buf_len % period_len)
+		return NULL;
+
+	return xilinx_dpdma_chan_prep_cyclic(chan, buf_addr, buf_len,
+						 period_len, flags);
+}
 
 static struct dma_async_tx_descriptor *
 xilinx_dpdma_prep_interleaved_dma(struct dma_chan *dchan,
@@ -1276,10 +1361,12 @@
 	struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan);
 	unsigned long flags;
 
-	spin_lock_irqsave(&chan->vchan.lock, flags);
+	spin_lock_irqsave(&chan->lock, flags);
+	spin_lock(&chan->vchan.lock);
 	if (vchan_issue_pending(&chan->vchan))
 		xilinx_dpdma_chan_queue_transfer(chan);
-	spin_unlock_irqrestore(&chan->vchan.lock, flags);
+	spin_unlock(&chan->vchan.lock);
+	spin_unlock_irqrestore(&chan->lock, flags);
 }
 
 static int xilinx_dpdma_config(struct dma_chan *dchan,
@@ -1503,7 +1590,9 @@
 		    XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id);
 
 	spin_lock_irqsave(&chan->lock, flags);
+	spin_lock(&chan->vchan.lock);
 	xilinx_dpdma_chan_queue_transfer(chan);
+	spin_unlock(&chan->vchan.lock);
 	spin_unlock_irqrestore(&chan->lock, flags);
 }
 
@@ -1677,6 +1766,7 @@
 
 	dma_cap_set(DMA_SLAVE, ddev->cap_mask);
 	dma_cap_set(DMA_PRIVATE, ddev->cap_mask);
+	dma_cap_set(DMA_CYCLIC, ddev->cap_mask);
 	dma_cap_set(DMA_INTERLEAVE, ddev->cap_mask);
 	dma_cap_set(DMA_REPEAT, ddev->cap_mask);
 	dma_cap_set(DMA_LOAD_EOT, ddev->cap_mask);
@@ -1684,6 +1774,7 @@
 
 	ddev->device_alloc_chan_resources = xilinx_dpdma_alloc_chan_resources;
 	ddev->device_free_chan_resources = xilinx_dpdma_free_chan_resources;
+	ddev->device_prep_dma_cyclic = xilinx_dpdma_prep_dma_cyclic;
 	ddev->device_prep_interleaved_dma = xilinx_dpdma_prep_interleaved_dma;
 	/* TODO: Can we achieve better granularity ? */
 	ddev->device_tx_status = dma_cookie_status;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/xilinx_frmbuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/xilinx_frmbuf.c
@@ -0,0 +1,1902 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DMAEngine driver for Xilinx Framebuffer IP
+ *
+ * Copyright (C) 2016 - 2021 Xilinx, Inc.
+ *
+ * Authors: Radhey Shyam Pandey <radheys@xilinx.com>
+ *          John Nichols <jnichol@xilinx.com>
+ *          Jeffrey Mouroux <jmouroux@xilinx.com>
+ *
+ * Based on the Freescale DMA driver.
+ *
+ * Description:
+ * The AXI Framebuffer core is a soft Xilinx IP core that
+ * provides high-bandwidth direct memory access between memory
+ * and AXI4-Stream.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dma/xilinx_frmbuf.h>
+#include <linux/dmapool.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_dma.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/videodev2.h>
+
+#include <drm/drm_fourcc.h>
+
+#include "../dmaengine.h"
+
+/* Register/Descriptor Offsets */
+#define XILINX_FRMBUF_CTRL_OFFSET		0x00
+#define XILINX_FRMBUF_GIE_OFFSET		0x04
+#define XILINX_FRMBUF_IE_OFFSET			0x08
+#define XILINX_FRMBUF_ISR_OFFSET		0x0c
+#define XILINX_FRMBUF_WIDTH_OFFSET		0x10
+#define XILINX_FRMBUF_HEIGHT_OFFSET		0x18
+#define XILINX_FRMBUF_STRIDE_OFFSET		0x20
+#define XILINX_FRMBUF_FMT_OFFSET		0x28
+#define XILINX_FRMBUF_ADDR_OFFSET		0x30
+#define XILINX_FRMBUF_ADDR2_OFFSET		0x3c
+#define XILINX_FRMBUF_FID_OFFSET		0x48
+#define XILINX_FRMBUF_FID_MODE_OFFSET	0x50
+#define XILINX_FRMBUF_ADDR3_OFFSET		0x54
+#define XILINX_FRMBUF_FID_ERR_OFFSET	0x58
+#define XILINX_FRMBUF_FID_OUT_OFFSET	0x60
+#define XILINX_FRMBUF_RD_ADDR3_OFFSET		0x74
+
+/* Control Registers */
+#define XILINX_FRMBUF_CTRL_AP_START		BIT(0)
+#define XILINX_FRMBUF_CTRL_AP_DONE		BIT(1)
+#define XILINX_FRMBUF_CTRL_AP_IDLE		BIT(2)
+#define XILINX_FRMBUF_CTRL_AP_READY		BIT(3)
+#define XILINX_FRMBUF_CTRL_FLUSH		BIT(5)
+#define XILINX_FRMBUF_CTRL_FLUSH_DONE		BIT(6)
+#define XILINX_FRMBUF_CTRL_AUTO_RESTART		BIT(7)
+#define XILINX_FRMBUF_GIE_EN			BIT(0)
+
+/* Interrupt Status and Control */
+#define XILINX_FRMBUF_IE_AP_DONE		BIT(0)
+#define XILINX_FRMBUF_IE_AP_READY		BIT(1)
+
+#define XILINX_FRMBUF_ISR_AP_DONE_IRQ		BIT(0)
+#define XILINX_FRMBUF_ISR_AP_READY_IRQ		BIT(1)
+
+#define XILINX_FRMBUF_ISR_ALL_IRQ_MASK	\
+		(XILINX_FRMBUF_ISR_AP_DONE_IRQ | \
+		XILINX_FRMBUF_ISR_AP_READY_IRQ)
+
+/* Video Format Register Settings */
+#define XILINX_FRMBUF_FMT_RGBX8			10
+#define XILINX_FRMBUF_FMT_YUVX8			11
+#define XILINX_FRMBUF_FMT_YUYV8			12
+#define XILINX_FRMBUF_FMT_RGBA8			13
+#define XILINX_FRMBUF_FMT_YUVA8			14
+#define XILINX_FRMBUF_FMT_RGBX10		15
+#define XILINX_FRMBUF_FMT_YUVX10		16
+#define XILINX_FRMBUF_FMT_Y_UV8			18
+#define XILINX_FRMBUF_FMT_Y_UV8_420		19
+#define XILINX_FRMBUF_FMT_RGB8			20
+#define XILINX_FRMBUF_FMT_YUV8			21
+#define XILINX_FRMBUF_FMT_Y_UV10		22
+#define XILINX_FRMBUF_FMT_Y_UV10_420		23
+#define XILINX_FRMBUF_FMT_Y8			24
+#define XILINX_FRMBUF_FMT_Y10			25
+#define XILINX_FRMBUF_FMT_BGRA8			26
+#define XILINX_FRMBUF_FMT_BGRX8			27
+#define XILINX_FRMBUF_FMT_UYVY8			28
+#define XILINX_FRMBUF_FMT_BGR8			29
+#define XILINX_FRMBUF_FMT_RGBX12		30
+#define XILINX_FRMBUF_FMT_RGB16			35
+#define XILINX_FRMBUF_FMT_Y_U_V8		42
+#define XILINX_FRMBUF_FMT_Y_U_V10		43
+
+/* FID Register */
+#define XILINX_FRMBUF_FID_MASK			BIT(0)
+
+/* FID ERR Register */
+#define XILINX_FRMBUF_FID_ERR_MASK		BIT(0)
+#define XILINX_FRMBUF_FID_OUT_MASK		BIT(0)
+
+#define XILINX_FRMBUF_ALIGN_MUL			8
+
+#define WAIT_FOR_FLUSH_DONE			25
+
+/* Pixels per clock property flag */
+#define XILINX_PPC_PROP				BIT(0)
+#define XILINX_FLUSH_PROP			BIT(1)
+#define XILINX_FID_PROP				BIT(2)
+#define XILINX_CLK_PROP				BIT(3)
+#define XILINX_THREE_PLANES_PROP		BIT(4)
+#define XILINX_FID_ERR_DETECT_PROP		BIT(5)
+
+#define XILINX_FRMBUF_MIN_HEIGHT		(64)
+#define XILINX_FRMBUF_MIN_WIDTH			(64)
+
+/**
+ * struct xilinx_frmbuf_desc_hw - Hardware Descriptor
+ * @luma_plane_addr: Luma or packed plane buffer address
+ * @chroma_plane_addr: Chroma plane buffer address
+ * @vsize: Vertical Size
+ * @hsize: Horizontal Size
+ * @stride: Number of bytes between the first
+ *	    pixels of each horizontal line
+ */
+struct xilinx_frmbuf_desc_hw {
+	dma_addr_t luma_plane_addr;
+	dma_addr_t chroma_plane_addr[2];
+	u32 vsize;
+	u32 hsize;
+	u32 stride;
+};
+
+/**
+ * struct xilinx_frmbuf_tx_descriptor - Per Transaction structure
+ * @async_tx: Async transaction descriptor
+ * @hw: Hardware descriptor
+ * @node: Node in the channel descriptors list
+ * @fid: Field ID of buffer
+ * @earlycb: Whether the callback should be called when in staged state
+ */
+struct xilinx_frmbuf_tx_descriptor {
+	struct dma_async_tx_descriptor async_tx;
+	struct xilinx_frmbuf_desc_hw hw;
+	struct list_head node;
+	u32 fid;
+	u32 earlycb;
+};
+
+/**
+ * struct xilinx_frmbuf_chan - Driver specific dma channel structure
+ * @xdev: Driver specific device structure
+ * @lock: Descriptor operation lock
+ * @chan_node: Member of a list of framebuffer channel instances
+ * @pending_list: Descriptors waiting
+ * @done_list: Complete descriptors
+ * @staged_desc: Next buffer to be programmed
+ * @active_desc: Currently active buffer being read/written to
+ * @common: DMA common channel
+ * @dev: The dma device
+ * @write_addr: callback that will write dma addresses to IP (32 or 64 bit)
+ * @irq: Channel IRQ
+ * @direction: Transfer direction
+ * @idle: Channel idle state
+ * @tasklet: Cleanup work after irq
+ * @vid_fmt: Reference to currently assigned video format description
+ * @hw_fid: FID enabled in hardware flag
+ * @mode: Select operation mode
+ * @fid_err_flag: Field id error detection flag
+ * @fid_out_val: Field id out val
+ * @fid_mode: Select fid mode
+ */
+struct xilinx_frmbuf_chan {
+	struct xilinx_frmbuf_device *xdev;
+	/* Descriptor operation lock */
+	spinlock_t lock;
+	struct list_head chan_node;
+	struct list_head pending_list;
+	struct list_head done_list;
+	struct xilinx_frmbuf_tx_descriptor *staged_desc;
+	struct xilinx_frmbuf_tx_descriptor *active_desc;
+	struct dma_chan common;
+	struct device *dev;
+	void (*write_addr)(struct xilinx_frmbuf_chan *chan, u32 reg,
+			   dma_addr_t value);
+	int irq;
+	enum dma_transfer_direction direction;
+	bool idle;
+	struct tasklet_struct tasklet;
+	const struct xilinx_frmbuf_format_desc *vid_fmt;
+	bool hw_fid;
+	enum operation_mode mode;
+	u8 fid_err_flag;
+	u8 fid_out_val;
+	enum fid_modes fid_mode;
+};
+
+/**
+ * struct xilinx_frmbuf_format_desc - lookup table to match fourcc to format
+ * @dts_name: Device tree name for this entry.
+ * @id: Format ID
+ * @bpw: Bits of pixel data + padding in a 32-bit word (luma plane for semi-pl)
+ * @ppw: Number of pixels represented in a 32-bit word (luma plane for semi-pl)
+ * @num_planes: Expected number of plane buffers in framebuffer for this format
+ * @drm_fmt: DRM video framework equivalent fourcc code
+ * @v4l2_fmt: Video 4 Linux framework equivalent fourcc code
+ * @fmt_bitmask: Flag identifying this format in device-specific "enabled"
+ *	bitmap
+ */
+struct xilinx_frmbuf_format_desc {
+	const char *dts_name;
+	u32 id;
+	u32 bpw;
+	u32 ppw;
+	u32 num_planes;
+	u32 drm_fmt;
+	u32 v4l2_fmt;
+	u32 fmt_bitmask;
+};
+
+static LIST_HEAD(frmbuf_chan_list);
+static DEFINE_MUTEX(frmbuf_chan_list_lock);
+
+static const struct xilinx_frmbuf_format_desc xilinx_frmbuf_formats[] = {
+	{
+		.dts_name = "xbgr8888",
+		.id = XILINX_FRMBUF_FMT_RGBX8,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_XBGR8888,
+		.v4l2_fmt = V4L2_PIX_FMT_BGRX32,
+		.fmt_bitmask = BIT(0),
+	},
+	{
+		.dts_name = "xbgr2101010",
+		.id = XILINX_FRMBUF_FMT_RGBX10,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_XBGR2101010,
+		.v4l2_fmt = V4L2_PIX_FMT_XBGR30,
+		.fmt_bitmask = BIT(1),
+	},
+	{
+		.dts_name = "xrgb8888",
+		.id = XILINX_FRMBUF_FMT_BGRX8,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_XRGB8888,
+		.v4l2_fmt = V4L2_PIX_FMT_XBGR32,
+		.fmt_bitmask = BIT(2),
+	},
+	{
+		.dts_name = "xvuy8888",
+		.id = XILINX_FRMBUF_FMT_YUVX8,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_XVUY8888,
+		.v4l2_fmt = V4L2_PIX_FMT_XVUY32,
+		.fmt_bitmask = BIT(5),
+	},
+	{
+		.dts_name = "vuy888",
+		.id = XILINX_FRMBUF_FMT_YUV8,
+		.bpw = 24,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_VUY888,
+		.v4l2_fmt = V4L2_PIX_FMT_VUY24,
+		.fmt_bitmask = BIT(6),
+	},
+	{
+		.dts_name = "yuvx2101010",
+		.id = XILINX_FRMBUF_FMT_YUVX10,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_XVUY2101010,
+		.v4l2_fmt = V4L2_PIX_FMT_XVUY10,
+		.fmt_bitmask = BIT(7),
+	},
+	{
+		.dts_name = "yuyv",
+		.id = XILINX_FRMBUF_FMT_YUYV8,
+		.bpw = 32,
+		.ppw = 2,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_YUYV,
+		.v4l2_fmt = V4L2_PIX_FMT_YUYV,
+		.fmt_bitmask = BIT(8),
+	},
+	{
+		.dts_name = "uyvy",
+		.id = XILINX_FRMBUF_FMT_UYVY8,
+		.bpw = 32,
+		.ppw = 2,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_UYVY,
+		.v4l2_fmt = V4L2_PIX_FMT_UYVY,
+		.fmt_bitmask = BIT(9),
+	},
+	{
+		.dts_name = "nv16",
+		.id = XILINX_FRMBUF_FMT_Y_UV8,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 2,
+		.drm_fmt = DRM_FORMAT_NV16,
+		.v4l2_fmt = V4L2_PIX_FMT_NV16M,
+		.fmt_bitmask = BIT(11),
+	},
+	{
+		.dts_name = "nv16",
+		.id = XILINX_FRMBUF_FMT_Y_UV8,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 2,
+		.drm_fmt = 0,
+		.v4l2_fmt = V4L2_PIX_FMT_NV16,
+		.fmt_bitmask = BIT(11),
+	},
+	{
+		.dts_name = "nv12",
+		.id = XILINX_FRMBUF_FMT_Y_UV8_420,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 2,
+		.drm_fmt = DRM_FORMAT_NV12,
+		.v4l2_fmt = V4L2_PIX_FMT_NV12M,
+		.fmt_bitmask = BIT(12),
+	},
+	{
+		.dts_name = "nv12",
+		.id = XILINX_FRMBUF_FMT_Y_UV8_420,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 2,
+		.drm_fmt = 0,
+		.v4l2_fmt = V4L2_PIX_FMT_NV12,
+		.fmt_bitmask = BIT(12),
+	},
+	{
+		.dts_name = "xv15",
+		.id = XILINX_FRMBUF_FMT_Y_UV10_420,
+		.bpw = 32,
+		.ppw = 3,
+		.num_planes = 2,
+		.drm_fmt = DRM_FORMAT_XV15,
+		.v4l2_fmt = V4L2_PIX_FMT_XV15M,
+		.fmt_bitmask = BIT(13),
+	},
+	{
+		.dts_name = "xv15",
+		.id = XILINX_FRMBUF_FMT_Y_UV10_420,
+		.bpw = 32,
+		.ppw = 3,
+		.num_planes = 2,
+		.drm_fmt = 0,
+		.v4l2_fmt = V4L2_PIX_FMT_XV15,
+		.fmt_bitmask = BIT(13),
+	},
+	{
+		.dts_name = "xv20",
+		.id = XILINX_FRMBUF_FMT_Y_UV10,
+		.bpw = 32,
+		.ppw = 3,
+		.num_planes = 2,
+		.drm_fmt = DRM_FORMAT_XV20,
+		.v4l2_fmt = V4L2_PIX_FMT_XV20M,
+		.fmt_bitmask = BIT(14),
+	},
+	{
+		.dts_name = "xv20",
+		.id = XILINX_FRMBUF_FMT_Y_UV10,
+		.bpw = 32,
+		.ppw = 3,
+		.num_planes = 2,
+		.drm_fmt = 0,
+		.v4l2_fmt = V4L2_PIX_FMT_XV20,
+		.fmt_bitmask = BIT(14),
+	},
+	{
+		.dts_name = "bgr888",
+		.id = XILINX_FRMBUF_FMT_RGB8,
+		.bpw = 24,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_BGR888,
+		.v4l2_fmt = V4L2_PIX_FMT_RGB24,
+		.fmt_bitmask = BIT(15),
+	},
+	{
+		.dts_name = "y8",
+		.id = XILINX_FRMBUF_FMT_Y8,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_Y8,
+		.v4l2_fmt = V4L2_PIX_FMT_GREY,
+		.fmt_bitmask = BIT(16),
+	},
+	{
+		.dts_name = "y10",
+		.id = XILINX_FRMBUF_FMT_Y10,
+		.bpw = 32,
+		.ppw = 3,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_Y10,
+		.v4l2_fmt = V4L2_PIX_FMT_XY10,
+		.fmt_bitmask = BIT(17),
+	},
+	{
+		.dts_name = "rgb888",
+		.id = XILINX_FRMBUF_FMT_BGR8,
+		.bpw = 24,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_RGB888,
+		.v4l2_fmt = V4L2_PIX_FMT_BGR24,
+		.fmt_bitmask = BIT(18),
+	},
+	{
+		.dts_name = "abgr8888",
+		.id = XILINX_FRMBUF_FMT_RGBA8,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_ABGR8888,
+		.v4l2_fmt = 0,
+		.fmt_bitmask = BIT(19),
+	},
+	{
+		.dts_name = "argb8888",
+		.id = XILINX_FRMBUF_FMT_BGRA8,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_ARGB8888,
+		.v4l2_fmt = 0,
+		.fmt_bitmask = BIT(20),
+	},
+	{
+		.dts_name = "avuy8888",
+		.id = XILINX_FRMBUF_FMT_YUVA8,
+		.bpw = 32,
+		.ppw = 1,
+		.num_planes = 1,
+		.drm_fmt = DRM_FORMAT_AVUY,
+		.v4l2_fmt = 0,
+		.fmt_bitmask = BIT(21),
+	},
+	{
+		.dts_name = "xbgr4121212",
+		.id = XILINX_FRMBUF_FMT_RGBX12,
+		.bpw = 40,
+		.ppw = 1,
+		.num_planes = 1,
+		.v4l2_fmt = V4L2_PIX_FMT_XBGR40,
+		.fmt_bitmask = BIT(22),
+	},
+	{
+		.dts_name = "rgb16",
+		.id = XILINX_FRMBUF_FMT_RGB16,
+		.bpw = 48,
+		.ppw = 1,
+		.num_planes = 1,
+		.v4l2_fmt = V4L2_PIX_FMT_BGR48,
+		.fmt_bitmask = BIT(23),
+	},
+	{
+		.dts_name = "y_u_v8",
+		.id = XILINX_FRMBUF_FMT_Y_U_V8,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 3,
+		.v4l2_fmt = V4L2_PIX_FMT_YUV444M,
+		.drm_fmt = DRM_FORMAT_YUV444,
+		.fmt_bitmask = BIT(24),
+	},
+	{
+		.dts_name = "y_u_v8",
+		.id = XILINX_FRMBUF_FMT_Y_U_V8,
+		.bpw = 32,
+		.ppw = 4,
+		.num_planes = 3,
+		.v4l2_fmt = V4L2_PIX_FMT_YUV444P,
+		.drm_fmt = DRM_FORMAT_YUV444,
+		.fmt_bitmask = BIT(24),
+	},
+	{
+		.dts_name = "y_u_v10",
+		.id = XILINX_FRMBUF_FMT_Y_U_V10,
+		.bpw = 32,
+		.ppw = 3,
+		.num_planes = 3,
+		.v4l2_fmt = V4L2_PIX_FMT_X403,
+		.drm_fmt = DRM_FORMAT_X403,
+		.fmt_bitmask = BIT(25),
+	},
+};
+
+/**
+ * struct xilinx_frmbuf_feature - dt or IP property structure
+ * @direction: dma transfer mode and direction
+ * @flags: Bitmask of properties enabled in IP or dt
+ */
+struct xilinx_frmbuf_feature {
+	enum dma_transfer_direction direction;
+	u32 flags;
+};
+
+/**
+ * struct xilinx_frmbuf_device - dma device structure
+ * @regs: I/O mapped base address
+ * @dev: Device Structure
+ * @common: DMA device structure
+ * @chan: Driver specific dma channel
+ * @rst_gpio: GPIO reset
+ * @enabled_vid_fmts: Bitmask of video formats enabled in hardware
+ * @drm_memory_fmts: Array of supported DRM fourcc codes
+ * @drm_fmt_cnt: Count of supported DRM fourcc codes
+ * @v4l2_memory_fmts: Array of supported V4L2 fourcc codes
+ * @v4l2_fmt_cnt: Count of supported V4L2 fourcc codes
+ * @cfg: Pointer to Framebuffer Feature config struct
+ * @max_width: Maximum pixel width supported in IP.
+ * @max_height: Maximum number of lines supported in IP.
+ * @ppc: Pixels per clock supported in IP.
+ * @ap_clk: Video core clock
+ */
+struct xilinx_frmbuf_device {
+	void __iomem *regs;
+	struct device *dev;
+	struct dma_device common;
+	struct xilinx_frmbuf_chan chan;
+	struct gpio_desc *rst_gpio;
+	u32 enabled_vid_fmts;
+	u32 drm_memory_fmts[ARRAY_SIZE(xilinx_frmbuf_formats)];
+	u32 drm_fmt_cnt;
+	u32 v4l2_memory_fmts[ARRAY_SIZE(xilinx_frmbuf_formats)];
+	u32 v4l2_fmt_cnt;
+	const struct xilinx_frmbuf_feature *cfg;
+	u32 max_width;
+	u32 max_height;
+	u32 ppc;
+	struct clk *ap_clk;
+};
+
+static const struct xilinx_frmbuf_feature xlnx_fbwr_cfg_v20 = {
+	.direction = DMA_DEV_TO_MEM,
+};
+
+static const struct xilinx_frmbuf_feature xlnx_fbwr_cfg_v21 = {
+	.direction = DMA_DEV_TO_MEM,
+	.flags = XILINX_PPC_PROP | XILINX_FLUSH_PROP
+		| XILINX_FID_PROP | XILINX_CLK_PROP,
+};
+
+static const struct xilinx_frmbuf_feature xlnx_fbwr_cfg_v22 = {
+	.direction = DMA_DEV_TO_MEM,
+	.flags = XILINX_PPC_PROP | XILINX_FLUSH_PROP
+		| XILINX_FID_PROP | XILINX_CLK_PROP
+		| XILINX_THREE_PLANES_PROP,
+};
+
+static const struct xilinx_frmbuf_feature xlnx_fbrd_cfg_v20 = {
+	.direction = DMA_MEM_TO_DEV,
+};
+
+static const struct xilinx_frmbuf_feature xlnx_fbrd_cfg_v21 = {
+	.direction = DMA_MEM_TO_DEV,
+	.flags = XILINX_PPC_PROP | XILINX_FLUSH_PROP
+		| XILINX_FID_PROP | XILINX_CLK_PROP,
+};
+
+static const struct xilinx_frmbuf_feature xlnx_fbrd_cfg_v22 = {
+	.direction = DMA_MEM_TO_DEV,
+	.flags = XILINX_PPC_PROP | XILINX_FLUSH_PROP
+		| XILINX_FID_PROP | XILINX_CLK_PROP
+		| XILINX_THREE_PLANES_PROP
+		| XILINX_FID_ERR_DETECT_PROP,
+};
+
+static const struct of_device_id xilinx_frmbuf_of_ids[] = {
+	{ .compatible = "xlnx,axi-frmbuf-wr-v2",
+		.data = (void *)&xlnx_fbwr_cfg_v20},
+	{ .compatible = "xlnx,axi-frmbuf-wr-v2.1",
+		.data = (void *)&xlnx_fbwr_cfg_v21},
+	{ .compatible = "xlnx,axi-frmbuf-wr-v2.2",
+		.data = (void *)&xlnx_fbwr_cfg_v22},
+	{ .compatible = "xlnx,axi-frmbuf-rd-v2",
+		.data = (void *)&xlnx_fbrd_cfg_v20},
+	{ .compatible = "xlnx,axi-frmbuf-rd-v2.1",
+		.data = (void *)&xlnx_fbrd_cfg_v21},
+	{ .compatible = "xlnx,axi-frmbuf-rd-v2.2",
+		.data = (void *)&xlnx_fbrd_cfg_v22},
+	{/* end of list */}
+};
+
+/******************************PROTOTYPES*************************************/
+#define to_xilinx_chan(chan) \
+	container_of(chan, struct xilinx_frmbuf_chan, common)
+#define to_dma_tx_descriptor(tx) \
+	container_of(tx, struct xilinx_frmbuf_tx_descriptor, async_tx)
+
+static inline u32 frmbuf_read(struct xilinx_frmbuf_chan *chan, u32 reg)
+{
+	return ioread32(chan->xdev->regs + reg);
+}
+
+static inline void frmbuf_write(struct xilinx_frmbuf_chan *chan, u32 reg,
+				u32 value)
+{
+	iowrite32(value, chan->xdev->regs + reg);
+}
+
+static inline void frmbuf_writeq(struct xilinx_frmbuf_chan *chan, u32 reg,
+				 u64 value)
+{
+	iowrite32(lower_32_bits(value), chan->xdev->regs + reg);
+	iowrite32(upper_32_bits(value), chan->xdev->regs + reg + 4);
+}
+
+static void writeq_addr(struct xilinx_frmbuf_chan *chan, u32 reg,
+			dma_addr_t addr)
+{
+	frmbuf_writeq(chan, reg, (u64)addr);
+}
+
+static void write_addr(struct xilinx_frmbuf_chan *chan, u32 reg,
+		       dma_addr_t addr)
+{
+	frmbuf_write(chan, reg, addr);
+}
+
+static inline void frmbuf_clr(struct xilinx_frmbuf_chan *chan, u32 reg,
+			      u32 clr)
+{
+	frmbuf_write(chan, reg, frmbuf_read(chan, reg) & ~clr);
+}
+
+static inline void frmbuf_set(struct xilinx_frmbuf_chan *chan, u32 reg,
+			      u32 set)
+{
+	frmbuf_write(chan, reg, frmbuf_read(chan, reg) | set);
+}
+
+static void frmbuf_init_format_array(struct xilinx_frmbuf_device *xdev)
+{
+	u32 i, cnt;
+
+	for (i = 0; i < ARRAY_SIZE(xilinx_frmbuf_formats); i++) {
+		if (!(xdev->enabled_vid_fmts &
+		      xilinx_frmbuf_formats[i].fmt_bitmask))
+			continue;
+
+		if (xilinx_frmbuf_formats[i].drm_fmt) {
+			cnt = xdev->drm_fmt_cnt++;
+			xdev->drm_memory_fmts[cnt] =
+				xilinx_frmbuf_formats[i].drm_fmt;
+		}
+
+		if (xilinx_frmbuf_formats[i].v4l2_fmt) {
+			cnt = xdev->v4l2_fmt_cnt++;
+			xdev->v4l2_memory_fmts[cnt] =
+				xilinx_frmbuf_formats[i].v4l2_fmt;
+		}
+	}
+}
+
+static struct xilinx_frmbuf_chan *frmbuf_find_chan(struct dma_chan *chan)
+{
+	struct xilinx_frmbuf_chan *xil_chan;
+	bool found_xchan = false;
+
+	mutex_lock(&frmbuf_chan_list_lock);
+	list_for_each_entry(xil_chan, &frmbuf_chan_list, chan_node) {
+		if (chan == &xil_chan->common) {
+			found_xchan = true;
+			break;
+		}
+	}
+	mutex_unlock(&frmbuf_chan_list_lock);
+
+	if (!found_xchan) {
+		dev_dbg(chan->device->dev,
+			"dma chan not a Video Framebuffer channel instance\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	return xil_chan;
+}
+
+static struct xilinx_frmbuf_device *frmbuf_find_dev(struct dma_chan *chan)
+{
+	struct xilinx_frmbuf_chan *xchan, *temp;
+	struct xilinx_frmbuf_device *xdev;
+	bool is_frmbuf_chan = false;
+
+	list_for_each_entry_safe(xchan, temp, &frmbuf_chan_list, chan_node) {
+		if (chan == &xchan->common)
+			is_frmbuf_chan = true;
+	}
+
+	if (!is_frmbuf_chan)
+		return ERR_PTR(-ENODEV);
+
+	xchan = to_xilinx_chan(chan);
+	xdev = container_of(xchan, struct xilinx_frmbuf_device, chan);
+
+	return xdev;
+}
+
+static int frmbuf_verify_format(struct dma_chan *chan, u32 fourcc, u32 type)
+{
+	struct xilinx_frmbuf_chan *xil_chan = to_xilinx_chan(chan);
+	u32 i, sz = ARRAY_SIZE(xilinx_frmbuf_formats);
+
+	for (i = 0; i < sz; i++) {
+		if ((type == XDMA_DRM &&
+		     fourcc != xilinx_frmbuf_formats[i].drm_fmt) ||
+		   (type == XDMA_V4L2 &&
+		    fourcc != xilinx_frmbuf_formats[i].v4l2_fmt))
+			continue;
+
+		if (!(xilinx_frmbuf_formats[i].fmt_bitmask &
+		      xil_chan->xdev->enabled_vid_fmts))
+			return -EINVAL;
+
+		/*
+		 * The Alpha color formats are supported in Framebuffer Read
+		 * IP only as corresponding DRM formats.
+		 */
+		if (type == XDMA_DRM &&
+		    (xilinx_frmbuf_formats[i].drm_fmt == DRM_FORMAT_ABGR8888 ||
+		     xilinx_frmbuf_formats[i].drm_fmt == DRM_FORMAT_ARGB8888 ||
+		     xilinx_frmbuf_formats[i].drm_fmt == DRM_FORMAT_AVUY) &&
+		    xil_chan->direction != DMA_MEM_TO_DEV)
+			return -EINVAL;
+
+		xil_chan->vid_fmt = &xilinx_frmbuf_formats[i];
+		return 0;
+	}
+	return -EINVAL;
+}
+
+static void xilinx_xdma_set_config(struct dma_chan *chan, u32 fourcc, u32 type)
+{
+	struct xilinx_frmbuf_chan *xil_chan;
+	struct xilinx_frmbuf_device *xdev;
+	const struct xilinx_frmbuf_format_desc *old_vid_fmt;
+	int ret;
+
+	xil_chan = frmbuf_find_chan(chan);
+	if (IS_ERR(xil_chan))
+		return;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return;
+
+	/* Save old video format */
+	old_vid_fmt = xil_chan->vid_fmt;
+
+	ret = frmbuf_verify_format(chan, fourcc, type);
+	if (ret == -EINVAL) {
+		dev_err(chan->device->dev,
+			"Framebuffer not configured for fourcc 0x%x\n",
+			fourcc);
+		return;
+	}
+
+	if ((!(xdev->cfg->flags & XILINX_THREE_PLANES_PROP)) &&
+	    (xil_chan->vid_fmt->id == XILINX_FRMBUF_FMT_Y_U_V8 ||
+	     xil_chan->vid_fmt->id == XILINX_FRMBUF_FMT_Y_U_V10)) {
+		dev_err(chan->device->dev, "doesn't support %s format\n",
+			xil_chan->vid_fmt->dts_name);
+		/* Restore to old video format */
+		xil_chan->vid_fmt = old_vid_fmt;
+		return;
+	}
+}
+
+void xilinx_xdma_set_mode(struct dma_chan *chan, enum operation_mode
+			  mode)
+{
+	struct xilinx_frmbuf_chan *xil_chan;
+
+	xil_chan = frmbuf_find_chan(chan);
+	if (IS_ERR(xil_chan))
+		return;
+
+	xil_chan->mode = mode;
+
+	return;
+
+} EXPORT_SYMBOL_GPL(xilinx_xdma_set_mode);
+
+void xilinx_xdma_drm_config(struct dma_chan *chan, u32 drm_fourcc)
+{
+	xilinx_xdma_set_config(chan, drm_fourcc, XDMA_DRM);
+
+} EXPORT_SYMBOL_GPL(xilinx_xdma_drm_config);
+
+void xilinx_xdma_v4l2_config(struct dma_chan *chan, u32 v4l2_fourcc)
+{
+	xilinx_xdma_set_config(chan, v4l2_fourcc, XDMA_V4L2);
+
+} EXPORT_SYMBOL_GPL(xilinx_xdma_v4l2_config);
+
+int xilinx_xdma_get_drm_vid_fmts(struct dma_chan *chan, u32 *fmt_cnt,
+				 u32 **fmts)
+{
+	struct xilinx_frmbuf_device *xdev;
+
+	xdev = frmbuf_find_dev(chan);
+
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	*fmt_cnt = xdev->drm_fmt_cnt;
+	*fmts = xdev->drm_memory_fmts;
+
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_drm_vid_fmts);
+
+int xilinx_xdma_get_v4l2_vid_fmts(struct dma_chan *chan, u32 *fmt_cnt,
+				  u32 **fmts)
+{
+	struct xilinx_frmbuf_device *xdev;
+
+	xdev = frmbuf_find_dev(chan);
+
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	*fmt_cnt = xdev->v4l2_fmt_cnt;
+	*fmts = xdev->v4l2_memory_fmts;
+
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_v4l2_vid_fmts);
+
+int xilinx_xdma_get_fid(struct dma_chan *chan,
+			struct dma_async_tx_descriptor *async_tx, u32 *fid)
+{
+	struct xilinx_frmbuf_device *xdev;
+	struct xilinx_frmbuf_tx_descriptor *desc;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	if (!async_tx || !fid)
+		return -EINVAL;
+
+	if (xdev->chan.direction != DMA_DEV_TO_MEM)
+		return -EINVAL;
+
+	desc = to_dma_tx_descriptor(async_tx);
+	if (!desc)
+		return -EINVAL;
+
+	*fid = desc->fid;
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_fid);
+
+int xilinx_xdma_set_fid(struct dma_chan *chan,
+			struct dma_async_tx_descriptor *async_tx, u32 fid)
+{
+	struct xilinx_frmbuf_device *xdev;
+	struct xilinx_frmbuf_tx_descriptor *desc;
+
+	if (fid > 1 || !async_tx)
+		return -EINVAL;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	if (xdev->chan.direction != DMA_MEM_TO_DEV)
+		return -EINVAL;
+
+	desc = to_dma_tx_descriptor(async_tx);
+	if (!desc)
+		return -EINVAL;
+
+	desc->fid = fid;
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_set_fid);
+
+int xilinx_xdma_get_fid_err_flag(struct dma_chan *chan,
+				 u32 *fid_err_flag)
+{
+	struct xilinx_frmbuf_device *xdev;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	if (xdev->chan.direction != DMA_MEM_TO_DEV || xdev->chan.idle)
+		return -EINVAL;
+
+	*fid_err_flag = xdev->chan.fid_err_flag;
+
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_fid_err_flag);
+
+int xilinx_xdma_get_fid_out(struct dma_chan *chan,
+			    u32 *fid_out_val)
+{
+	struct xilinx_frmbuf_device *xdev;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	if (xdev->chan.direction != DMA_MEM_TO_DEV || xdev->chan.idle)
+		return -EINVAL;
+
+	*fid_out_val = xdev->chan.fid_out_val;
+
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_fid_out);
+
+int xilinx_xdma_get_width_align(struct dma_chan *chan, u32 *width_align)
+{
+	struct xilinx_frmbuf_device *xdev;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+	*width_align = xdev->ppc;
+
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_width_align);
+
+int xilinx_xdma_get_earlycb(struct dma_chan *chan,
+			    struct dma_async_tx_descriptor *async_tx,
+			    u32 *earlycb)
+{
+	struct xilinx_frmbuf_device *xdev;
+	struct xilinx_frmbuf_tx_descriptor *desc;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	if (!async_tx || !earlycb)
+		return -EINVAL;
+
+	desc = to_dma_tx_descriptor(async_tx);
+	if (!desc)
+		return -EINVAL;
+
+	*earlycb = desc->earlycb;
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_get_earlycb);
+
+int xilinx_xdma_set_earlycb(struct dma_chan *chan,
+			    struct dma_async_tx_descriptor *async_tx,
+			    u32 earlycb)
+{
+	struct xilinx_frmbuf_device *xdev;
+	struct xilinx_frmbuf_tx_descriptor *desc;
+
+	if (!async_tx)
+		return -EINVAL;
+
+	xdev = frmbuf_find_dev(chan);
+	if (IS_ERR(xdev))
+		return PTR_ERR(xdev);
+
+	desc = to_dma_tx_descriptor(async_tx);
+	if (!desc)
+		return -EINVAL;
+
+	desc->earlycb = earlycb;
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_xdma_set_earlycb);
+
+/**
+ * of_dma_xilinx_xlate - Translation function
+ * @dma_spec: Pointer to DMA specifier as found in the device tree
+ * @ofdma: Pointer to DMA controller data
+ *
+ * Return: DMA channel pointer on success or error code on error
+ */
+static struct dma_chan *of_dma_xilinx_xlate(struct of_phandle_args *dma_spec,
+					    struct of_dma *ofdma)
+{
+	struct xilinx_frmbuf_device *xdev = ofdma->of_dma_data;
+
+	return dma_get_slave_channel(&xdev->chan.common);
+}
+
+/* -----------------------------------------------------------------------------
+ * Descriptors alloc and free
+ */
+
+/**
+ * xilinx_frmbuf_alloc_tx_descriptor - Allocate transaction descriptor
+ * @chan: Driver specific dma channel
+ *
+ * Return: The allocated descriptor on success and NULL on failure.
+ */
+static struct xilinx_frmbuf_tx_descriptor *
+xilinx_frmbuf_alloc_tx_descriptor(struct xilinx_frmbuf_chan *chan)
+{
+	struct xilinx_frmbuf_tx_descriptor *desc;
+
+	desc = kzalloc(sizeof(*desc), GFP_KERNEL);
+	if (!desc)
+		return NULL;
+
+	return desc;
+}
+
+/**
+ * xilinx_frmbuf_free_desc_list - Free descriptors list
+ * @chan: Driver specific dma channel
+ * @list: List to parse and delete the descriptor
+ */
+static void xilinx_frmbuf_free_desc_list(struct xilinx_frmbuf_chan *chan,
+					 struct list_head *list)
+{
+	struct xilinx_frmbuf_tx_descriptor *desc, *next;
+
+	list_for_each_entry_safe(desc, next, list, node) {
+		list_del(&desc->node);
+		kfree(desc);
+	}
+}
+
+/**
+ * xilinx_frmbuf_free_descriptors - Free channel descriptors
+ * @chan: Driver specific dma channel
+ */
+static void xilinx_frmbuf_free_descriptors(struct xilinx_frmbuf_chan *chan)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	xilinx_frmbuf_free_desc_list(chan, &chan->pending_list);
+	xilinx_frmbuf_free_desc_list(chan, &chan->done_list);
+	kfree(chan->active_desc);
+	kfree(chan->staged_desc);
+
+	chan->staged_desc = NULL;
+	chan->active_desc = NULL;
+	INIT_LIST_HEAD(&chan->pending_list);
+	INIT_LIST_HEAD(&chan->done_list);
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_frmbuf_free_chan_resources - Free channel resources
+ * @dchan: DMA channel
+ */
+static void xilinx_frmbuf_free_chan_resources(struct dma_chan *dchan)
+{
+	struct xilinx_frmbuf_chan *chan = to_xilinx_chan(dchan);
+
+	xilinx_frmbuf_free_descriptors(chan);
+}
+
+/**
+ * xilinx_frmbuf_chan_desc_cleanup - Clean channel descriptors
+ * @chan: Driver specific dma channel
+ */
+static void xilinx_frmbuf_chan_desc_cleanup(struct xilinx_frmbuf_chan *chan)
+{
+	struct xilinx_frmbuf_tx_descriptor *desc, *next;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	list_for_each_entry_safe(desc, next, &chan->done_list, node) {
+		dma_async_tx_callback callback;
+		void *callback_param;
+
+		list_del(&desc->node);
+
+		/* Run the link descriptor callback function */
+		callback = desc->async_tx.callback;
+		callback_param = desc->async_tx.callback_param;
+		if (callback) {
+			spin_unlock_irqrestore(&chan->lock, flags);
+			callback(callback_param);
+			spin_lock_irqsave(&chan->lock, flags);
+		}
+
+		/* Run any dependencies, then free the descriptor */
+		dma_run_dependencies(&desc->async_tx);
+		kfree(desc);
+	}
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_frmbuf_do_tasklet - Schedule completion tasklet
+ * @data: Pointer to the Xilinx frmbuf channel structure
+ */
+static void xilinx_frmbuf_do_tasklet(unsigned long data)
+{
+	struct xilinx_frmbuf_chan *chan = (struct xilinx_frmbuf_chan *)data;
+
+	xilinx_frmbuf_chan_desc_cleanup(chan);
+}
+
+/**
+ * xilinx_frmbuf_alloc_chan_resources - Allocate channel resources
+ * @dchan: DMA channel
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_frmbuf_alloc_chan_resources(struct dma_chan *dchan)
+{
+	dma_cookie_init(dchan);
+
+	return 0;
+}
+
+/**
+ * xilinx_frmbuf_tx_status - Get frmbuf transaction status
+ * @dchan: DMA channel
+ * @cookie: Transaction identifier
+ * @txstate: Transaction state
+ *
+ * Return: fmrbuf transaction status
+ */
+static enum dma_status xilinx_frmbuf_tx_status(struct dma_chan *dchan,
+					       dma_cookie_t cookie,
+					       struct dma_tx_state *txstate)
+{
+	return dma_cookie_status(dchan, cookie, txstate);
+}
+
+/**
+ * xilinx_frmbuf_halt - Halt frmbuf channel
+ * @chan: Driver specific dma channel
+ */
+static void xilinx_frmbuf_halt(struct xilinx_frmbuf_chan *chan)
+{
+	frmbuf_clr(chan, XILINX_FRMBUF_CTRL_OFFSET,
+		   XILINX_FRMBUF_CTRL_AP_START | chan->mode);
+	chan->idle = true;
+}
+
+/**
+ * xilinx_frmbuf_start - Start dma channel
+ * @chan: Driver specific dma channel
+ */
+static void xilinx_frmbuf_start(struct xilinx_frmbuf_chan *chan)
+{
+	frmbuf_set(chan, XILINX_FRMBUF_CTRL_OFFSET,
+		   XILINX_FRMBUF_CTRL_AP_START | chan->mode);
+	chan->idle = false;
+}
+
+/**
+ * xilinx_frmbuf_complete_descriptor - Mark the active descriptor as complete
+ * This function is invoked with spinlock held
+ * @chan : xilinx frmbuf channel
+ *
+ * CONTEXT: hardirq
+ */
+static void xilinx_frmbuf_complete_descriptor(struct xilinx_frmbuf_chan *chan)
+{
+	struct xilinx_frmbuf_tx_descriptor *desc = chan->active_desc;
+
+	/*
+	 * In case of frame buffer write, read the fid register
+	 * and associate it with descriptor
+	 */
+	if (chan->direction == DMA_DEV_TO_MEM && chan->hw_fid)
+		desc->fid = frmbuf_read(chan, XILINX_FRMBUF_FID_OFFSET) &
+			    XILINX_FRMBUF_FID_MASK;
+
+	dma_cookie_complete(&desc->async_tx);
+	list_add_tail(&desc->node, &chan->done_list);
+}
+
+/**
+ * xilinx_frmbuf_start_transfer - Starts frmbuf transfer
+ * @chan: Driver specific channel struct pointer
+ */
+static void xilinx_frmbuf_start_transfer(struct xilinx_frmbuf_chan *chan)
+{
+	struct xilinx_frmbuf_tx_descriptor *desc;
+	struct xilinx_frmbuf_device *xdev;
+
+	xdev = container_of(chan, struct xilinx_frmbuf_device, chan);
+
+	if (!chan->idle)
+		return;
+
+	if (chan->staged_desc) {
+		chan->active_desc = chan->staged_desc;
+		chan->staged_desc = NULL;
+	}
+
+	if (list_empty(&chan->pending_list))
+		return;
+
+	desc = list_first_entry(&chan->pending_list,
+				struct xilinx_frmbuf_tx_descriptor,
+				node);
+
+	if (desc->earlycb == EARLY_CALLBACK_START_DESC) {
+		dma_async_tx_callback callback;
+		void *callback_param;
+
+		callback = desc->async_tx.callback;
+		callback_param = desc->async_tx.callback_param;
+		if (callback) {
+			callback(callback_param);
+			desc->async_tx.callback = NULL;
+			chan->active_desc = desc;
+		}
+	}
+
+	/* Start the transfer */
+	chan->write_addr(chan, XILINX_FRMBUF_ADDR_OFFSET,
+			 desc->hw.luma_plane_addr);
+	chan->write_addr(chan, XILINX_FRMBUF_ADDR2_OFFSET,
+			 desc->hw.chroma_plane_addr[0]);
+	if (xdev->cfg->flags & XILINX_THREE_PLANES_PROP) {
+		if (chan->direction == DMA_MEM_TO_DEV)
+			chan->write_addr(chan, XILINX_FRMBUF_RD_ADDR3_OFFSET,
+					 desc->hw.chroma_plane_addr[1]);
+		else
+			chan->write_addr(chan, XILINX_FRMBUF_ADDR3_OFFSET,
+					 desc->hw.chroma_plane_addr[1]);
+	}
+
+	/* HW expects these parameters to be same for one transaction */
+	frmbuf_write(chan, XILINX_FRMBUF_WIDTH_OFFSET, desc->hw.hsize);
+	frmbuf_write(chan, XILINX_FRMBUF_STRIDE_OFFSET, desc->hw.stride);
+	frmbuf_write(chan, XILINX_FRMBUF_HEIGHT_OFFSET, desc->hw.vsize);
+	frmbuf_write(chan, XILINX_FRMBUF_FMT_OFFSET, chan->vid_fmt->id);
+
+	/* If it is framebuffer read IP set the FID */
+	if (chan->direction == DMA_MEM_TO_DEV && chan->hw_fid)
+		frmbuf_write(chan, XILINX_FRMBUF_FID_OFFSET, desc->fid);
+
+	/* Start the hardware */
+	xilinx_frmbuf_start(chan);
+	list_del(&desc->node);
+
+	/* No staging descriptor required when auto restart is disabled */
+	if (chan->mode == AUTO_RESTART)
+		chan->staged_desc = desc;
+	else
+		chan->active_desc = desc;
+}
+
+/**
+ * xilinx_frmbuf_issue_pending - Issue pending transactions
+ * @dchan: DMA channel
+ */
+static void xilinx_frmbuf_issue_pending(struct dma_chan *dchan)
+{
+	struct xilinx_frmbuf_chan *chan = to_xilinx_chan(dchan);
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+	xilinx_frmbuf_start_transfer(chan);
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_frmbuf_reset - Reset frmbuf channel
+ * @chan: Driver specific dma channel
+ */
+static void xilinx_frmbuf_reset(struct xilinx_frmbuf_chan *chan)
+{
+	/* reset ip */
+	gpiod_set_value(chan->xdev->rst_gpio, 1);
+	udelay(1);
+	gpiod_set_value(chan->xdev->rst_gpio, 0);
+}
+
+/**
+ * xilinx_frmbuf_chan_reset - Reset frmbuf channel and enable interrupts
+ * @chan: Driver specific frmbuf channel
+ */
+static void xilinx_frmbuf_chan_reset(struct xilinx_frmbuf_chan *chan)
+{
+	xilinx_frmbuf_reset(chan);
+	frmbuf_write(chan, XILINX_FRMBUF_IE_OFFSET, XILINX_FRMBUF_IE_AP_DONE);
+	frmbuf_write(chan, XILINX_FRMBUF_GIE_OFFSET, XILINX_FRMBUF_GIE_EN);
+	chan->fid_err_flag = 0;
+	chan->fid_out_val = 0;
+}
+
+/**
+ * xilinx_frmbuf_irq_handler - frmbuf Interrupt handler
+ * @irq: IRQ number
+ * @data: Pointer to the Xilinx frmbuf channel structure
+ *
+ * Return: IRQ_HANDLED/IRQ_NONE
+ */
+static irqreturn_t xilinx_frmbuf_irq_handler(int irq, void *data)
+{
+	struct xilinx_frmbuf_chan *chan = data;
+	u32 status;
+	dma_async_tx_callback callback = NULL;
+	void *callback_param;
+	struct xilinx_frmbuf_tx_descriptor *desc;
+
+	status = frmbuf_read(chan, XILINX_FRMBUF_ISR_OFFSET);
+	if (!(status & XILINX_FRMBUF_ISR_ALL_IRQ_MASK))
+		return IRQ_NONE;
+
+	frmbuf_write(chan, XILINX_FRMBUF_ISR_OFFSET,
+		     status & XILINX_FRMBUF_ISR_ALL_IRQ_MASK);
+
+	/* Check if callback function needs to be called early */
+	desc = chan->staged_desc;
+	if (desc && desc->earlycb == EARLY_CALLBACK) {
+		callback = desc->async_tx.callback;
+		callback_param = desc->async_tx.callback_param;
+		if (callback) {
+			callback(callback_param);
+			desc->async_tx.callback = NULL;
+		}
+	}
+
+	if (status & XILINX_FRMBUF_ISR_AP_DONE_IRQ) {
+		spin_lock(&chan->lock);
+		chan->idle = true;
+		if (chan->active_desc) {
+			xilinx_frmbuf_complete_descriptor(chan);
+			chan->active_desc = NULL;
+		}
+
+		/* Update fid err detect flag and out value */
+		if (chan->direction == DMA_MEM_TO_DEV &&
+		    chan->hw_fid && chan->idle &&
+		    chan->xdev->cfg->flags & XILINX_FID_ERR_DETECT_PROP) {
+			if (chan->mode == AUTO_RESTART)
+				chan->fid_mode = FID_MODE_2;
+			else
+				chan->fid_mode = FID_MODE_1;
+
+			frmbuf_write(chan, XILINX_FRMBUF_FID_MODE_OFFSET,
+				     chan->fid_mode);
+			dev_dbg(chan->xdev->dev, "fid mode = %d\n",
+				frmbuf_read(chan, XILINX_FRMBUF_FID_MODE_OFFSET));
+
+			chan->fid_err_flag = frmbuf_read(chan,
+							 XILINX_FRMBUF_FID_ERR_OFFSET) &
+							XILINX_FRMBUF_FID_ERR_MASK;
+			chan->fid_out_val = frmbuf_read(chan,
+							XILINX_FRMBUF_FID_OUT_OFFSET) &
+							XILINX_FRMBUF_FID_OUT_MASK;
+			dev_dbg(chan->xdev->dev, "fid err cnt = 0x%x\n",
+				frmbuf_read(chan, XILINX_FRMBUF_FID_ERR_OFFSET));
+		}
+
+		xilinx_frmbuf_start_transfer(chan);
+		spin_unlock(&chan->lock);
+	}
+
+	tasklet_schedule(&chan->tasklet);
+	return IRQ_HANDLED;
+}
+
+/**
+ * xilinx_frmbuf_tx_submit - Submit DMA transaction
+ * @tx: Async transaction descriptor
+ *
+ * Return: cookie value on success and failure value on error
+ */
+static dma_cookie_t xilinx_frmbuf_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+	struct xilinx_frmbuf_tx_descriptor *desc = to_dma_tx_descriptor(tx);
+	struct xilinx_frmbuf_chan *chan = to_xilinx_chan(tx->chan);
+	dma_cookie_t cookie;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+	cookie = dma_cookie_assign(tx);
+	list_add_tail(&desc->node, &chan->pending_list);
+	spin_unlock_irqrestore(&chan->lock, flags);
+
+	return cookie;
+}
+
+/**
+ * xilinx_frmbuf_dma_prep_interleaved - prepare a descriptor for a
+ *	DMA_SLAVE transaction
+ * @dchan: DMA channel
+ * @xt: Interleaved template pointer
+ * @flags: transfer ack flags
+ *
+ * Return: Async transaction descriptor on success and NULL on failure
+ */
+static struct dma_async_tx_descriptor *
+xilinx_frmbuf_dma_prep_interleaved(struct dma_chan *dchan,
+				   struct dma_interleaved_template *xt,
+				   unsigned long flags)
+{
+	struct xilinx_frmbuf_chan *chan = to_xilinx_chan(dchan);
+	struct xilinx_frmbuf_tx_descriptor *desc;
+	struct xilinx_frmbuf_desc_hw *hw;
+	u32 vsize, hsize;
+
+	if (chan->direction != xt->dir || !chan->vid_fmt)
+		goto error;
+
+	if (!xt->numf || !xt->sgl[0].size)
+		goto error;
+
+	if (xt->frame_size != chan->vid_fmt->num_planes)
+		goto error;
+
+	vsize = xt->numf;
+	hsize = (xt->sgl[0].size * chan->vid_fmt->ppw * 8) /
+		 chan->vid_fmt->bpw;
+	/* hsize calc should not have resulted in an odd number */
+	if (hsize & 1)
+		hsize++;
+
+	if (vsize > chan->xdev->max_height || hsize > chan->xdev->max_width) {
+		dev_dbg(chan->xdev->dev,
+			"vsize %d max vsize %d hsize %d max hsize %d\n",
+			vsize, chan->xdev->max_height, hsize,
+			chan->xdev->max_width);
+		dev_err(chan->xdev->dev, "Requested size not supported!\n");
+		goto error;
+	}
+
+	desc = xilinx_frmbuf_alloc_tx_descriptor(chan);
+	if (!desc)
+		return NULL;
+
+	dma_async_tx_descriptor_init(&desc->async_tx, &chan->common);
+	desc->async_tx.tx_submit = xilinx_frmbuf_tx_submit;
+	async_tx_ack(&desc->async_tx);
+
+	hw = &desc->hw;
+	hw->vsize = xt->numf;
+	hw->stride = xt->sgl[0].icg + xt->sgl[0].size;
+	hw->hsize = (xt->sgl[0].size * chan->vid_fmt->ppw * 8) /
+		     chan->vid_fmt->bpw;
+
+	/* hsize calc should not have resulted in an odd number */
+	if (hw->hsize & 1)
+		hw->hsize++;
+
+	if (chan->direction == DMA_MEM_TO_DEV) {
+		hw->luma_plane_addr = xt->src_start;
+		if (xt->frame_size == 2 || xt->frame_size == 3)
+			hw->chroma_plane_addr[0] =
+				xt->src_start +
+				xt->numf * hw->stride +
+				xt->sgl[0].src_icg;
+		if (xt->frame_size == 3)
+			hw->chroma_plane_addr[1] =
+				hw->chroma_plane_addr[0] +
+				xt->numf * hw->stride +
+				xt->sgl[0].src_icg;
+	} else {
+		hw->luma_plane_addr = xt->dst_start;
+		if (xt->frame_size == 2 || xt->frame_size == 3)
+			hw->chroma_plane_addr[0] =
+				xt->dst_start +
+				xt->numf * hw->stride +
+				xt->sgl[0].dst_icg;
+		if (xt->frame_size == 3)
+			hw->chroma_plane_addr[1] =
+				hw->chroma_plane_addr[0] +
+				xt->numf * hw->stride +
+				xt->sgl[0].dst_icg;
+	}
+
+	return &desc->async_tx;
+
+error:
+	dev_err(chan->xdev->dev,
+		"Invalid dma template or missing dma video fmt config\n");
+	return NULL;
+}
+
+/**
+ * xilinx_frmbuf_terminate_all - Halt the channel and free descriptors
+ * @dchan: Driver specific dma channel pointer
+ *
+ * Return: 0
+ */
+static int xilinx_frmbuf_terminate_all(struct dma_chan *dchan)
+{
+	struct xilinx_frmbuf_chan *chan = to_xilinx_chan(dchan);
+
+	xilinx_frmbuf_halt(chan);
+	xilinx_frmbuf_free_descriptors(chan);
+	/* worst case frame-to-frame boundary; ensure frame output complete */
+	msleep(50);
+
+	if (chan->xdev->cfg->flags & XILINX_FLUSH_PROP) {
+		u8 count;
+
+		/*
+		 * Flush the framebuffer FIFO and
+		 * wait for max 50ms for flush done
+		 */
+		frmbuf_set(chan, XILINX_FRMBUF_CTRL_OFFSET,
+			   XILINX_FRMBUF_CTRL_FLUSH);
+		for (count = WAIT_FOR_FLUSH_DONE; count > 0; count--) {
+			if (frmbuf_read(chan, XILINX_FRMBUF_CTRL_OFFSET) &
+					XILINX_FRMBUF_CTRL_FLUSH_DONE)
+				break;
+			usleep_range(2000, 2100);
+		}
+
+		if (!count)
+			dev_err(chan->xdev->dev, "Framebuffer Flush not done!\n");
+	}
+
+	xilinx_frmbuf_chan_reset(chan);
+
+	return 0;
+}
+
+/**
+ * xilinx_frmbuf_synchronize - kill tasklet to stop further descr processing
+ * @dchan: Driver specific dma channel pointer
+ */
+static void xilinx_frmbuf_synchronize(struct dma_chan *dchan)
+{
+	struct xilinx_frmbuf_chan *chan = to_xilinx_chan(dchan);
+
+	tasklet_kill(&chan->tasklet);
+}
+
+/* -----------------------------------------------------------------------------
+ * Probe and remove
+ */
+
+/**
+ * xilinx_frmbuf_chan_remove - Per Channel remove function
+ * @chan: Driver specific dma channel
+ */
+static void xilinx_frmbuf_chan_remove(struct xilinx_frmbuf_chan *chan)
+{
+	/* Disable all interrupts */
+	frmbuf_clr(chan, XILINX_FRMBUF_IE_OFFSET,
+		   XILINX_FRMBUF_ISR_ALL_IRQ_MASK);
+
+	tasklet_kill(&chan->tasklet);
+	list_del(&chan->common.device_node);
+
+	mutex_lock(&frmbuf_chan_list_lock);
+	list_del(&chan->chan_node);
+	mutex_unlock(&frmbuf_chan_list_lock);
+}
+
+/**
+ * xilinx_frmbuf_chan_probe - Per Channel Probing
+ * It get channel features from the device tree entry and
+ * initialize special channel handling routines
+ *
+ * @xdev: Driver specific device structure
+ * @node: Device node
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_frmbuf_chan_probe(struct xilinx_frmbuf_device *xdev,
+				    struct device_node *node)
+{
+	struct xilinx_frmbuf_chan *chan;
+	int err;
+	u32 dma_addr_size = 0;
+
+	chan = &xdev->chan;
+
+	chan->dev = xdev->dev;
+	chan->xdev = xdev;
+	chan->idle = true;
+	chan->fid_err_flag = 0;
+	chan->fid_out_val = 0;
+	chan->mode = AUTO_RESTART;
+
+	err = of_property_read_u32(node, "xlnx,dma-addr-width",
+				   &dma_addr_size);
+	if (err || (dma_addr_size != 32 && dma_addr_size != 64)) {
+		dev_err(xdev->dev, "missing or invalid addr width dts prop\n");
+		return err;
+	}
+
+	if (dma_addr_size == 64 && sizeof(dma_addr_t) == sizeof(u64))
+		chan->write_addr = writeq_addr;
+	else
+		chan->write_addr = write_addr;
+
+	if (xdev->cfg->flags & XILINX_FID_PROP)
+		chan->hw_fid = of_property_read_bool(node, "xlnx,fid");
+
+	spin_lock_init(&chan->lock);
+	INIT_LIST_HEAD(&chan->pending_list);
+	INIT_LIST_HEAD(&chan->done_list);
+
+	chan->irq = irq_of_parse_and_map(node, 0);
+	err = devm_request_irq(xdev->dev, chan->irq, xilinx_frmbuf_irq_handler,
+			       IRQF_SHARED, "xilinx_framebuffer", chan);
+
+	if (err) {
+		dev_err(xdev->dev, "unable to request IRQ %d\n", chan->irq);
+		return err;
+	}
+
+	tasklet_init(&chan->tasklet, xilinx_frmbuf_do_tasklet,
+		     (unsigned long)chan);
+
+	/*
+	 * Initialize the DMA channel and add it to the DMA engine channels
+	 * list.
+	 */
+	chan->common.device = &xdev->common;
+
+	list_add_tail(&chan->common.device_node, &xdev->common.channels);
+
+	mutex_lock(&frmbuf_chan_list_lock);
+	list_add_tail(&chan->chan_node, &frmbuf_chan_list);
+	mutex_unlock(&frmbuf_chan_list_lock);
+
+	xilinx_frmbuf_chan_reset(chan);
+
+	return 0;
+}
+
+/**
+ * xilinx_frmbuf_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_frmbuf_probe(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct xilinx_frmbuf_device *xdev;
+	struct resource *io;
+	enum dma_transfer_direction dma_dir;
+	const struct of_device_id *match;
+	int err;
+	u32 i, j, align, max_width, max_height;
+	int hw_vid_fmt_cnt;
+	const char *vid_fmts[ARRAY_SIZE(xilinx_frmbuf_formats)];
+
+	xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL);
+	if (!xdev)
+		return -ENOMEM;
+
+	xdev->dev = &pdev->dev;
+
+	match = of_match_node(xilinx_frmbuf_of_ids, node);
+	if (!match)
+		return -ENODEV;
+
+	xdev->cfg = match->data;
+
+	dma_dir = (enum dma_transfer_direction)xdev->cfg->direction;
+
+	if (xdev->cfg->flags & XILINX_CLK_PROP) {
+		xdev->ap_clk = devm_clk_get(xdev->dev, "ap_clk");
+		if (IS_ERR(xdev->ap_clk)) {
+			err = PTR_ERR(xdev->ap_clk);
+			dev_err(xdev->dev, "failed to get ap_clk (%d)\n", err);
+			return err;
+		}
+	} else {
+		dev_info(xdev->dev, "assuming clock is enabled!\n");
+	}
+
+	xdev->rst_gpio = devm_gpiod_get(&pdev->dev, "reset",
+					GPIOD_OUT_HIGH);
+	if (IS_ERR(xdev->rst_gpio)) {
+		err = PTR_ERR(xdev->rst_gpio);
+		if (err == -EPROBE_DEFER)
+			dev_info(&pdev->dev,
+				 "Probe deferred due to GPIO reset defer\n");
+		else
+			dev_err(&pdev->dev,
+				"Unable to locate reset property in dt\n");
+		return err;
+	}
+
+	gpiod_set_value_cansleep(xdev->rst_gpio, 0x0);
+
+	io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xdev->regs = devm_ioremap_resource(&pdev->dev, io);
+	if (IS_ERR(xdev->regs))
+		return PTR_ERR(xdev->regs);
+
+	if (xdev->cfg->flags & XILINX_THREE_PLANES_PROP)
+		max_height = 8640;
+	else
+		max_height = 4320;
+
+	err = of_property_read_u32(node, "xlnx,max-height", &xdev->max_height);
+	if (err < 0) {
+		dev_err(xdev->dev, "xlnx,max-height is missing!");
+		return -EINVAL;
+	} else if (xdev->max_height > max_height ||
+		   xdev->max_height < XILINX_FRMBUF_MIN_HEIGHT) {
+		dev_err(&pdev->dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	if (xdev->cfg->flags & XILINX_THREE_PLANES_PROP)
+		max_width = 15360;
+	else
+		max_width = 8192;
+
+	err = of_property_read_u32(node, "xlnx,max-width", &xdev->max_width);
+	if (err < 0) {
+		dev_err(xdev->dev, "xlnx,max-width is missing!");
+		return -EINVAL;
+	} else if (xdev->max_width > max_width ||
+		   xdev->max_width < XILINX_FRMBUF_MIN_WIDTH) {
+		dev_err(&pdev->dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	/* Initialize the DMA engine */
+	if (xdev->cfg->flags & XILINX_PPC_PROP) {
+		err = of_property_read_u32(node, "xlnx,pixels-per-clock", &xdev->ppc);
+		if (err || (xdev->ppc != 1 && xdev->ppc != 2 &&
+			    xdev->ppc != 4 && xdev->ppc != 8)) {
+			dev_err(&pdev->dev, "missing or invalid pixels per clock dts prop\n");
+			return err;
+		}
+		err = of_property_read_u32(node, "xlnx,dma-align", &align);
+		if (err)
+			align = xdev->ppc * XILINX_FRMBUF_ALIGN_MUL;
+
+		if (align < (xdev->ppc * XILINX_FRMBUF_ALIGN_MUL) ||
+		    ffs(align) != fls(align)) {
+			dev_err(&pdev->dev, "invalid dma align dts prop\n");
+			return -EINVAL;
+		}
+	} else {
+		align = 16;
+	}
+
+	xdev->common.copy_align = (enum dmaengine_alignment)(fls(align) - 1);
+	xdev->common.dev = &pdev->dev;
+
+	if (xdev->cfg->flags & XILINX_CLK_PROP) {
+		err = clk_prepare_enable(xdev->ap_clk);
+		if (err) {
+			dev_err(&pdev->dev, " failed to enable ap_clk (%d)\n",
+				err);
+			return err;
+		}
+	}
+
+	INIT_LIST_HEAD(&xdev->common.channels);
+	dma_cap_set(DMA_SLAVE, xdev->common.cap_mask);
+	dma_cap_set(DMA_PRIVATE, xdev->common.cap_mask);
+
+	/* Initialize the channels */
+	err = xilinx_frmbuf_chan_probe(xdev, node);
+	if (err < 0)
+		goto disable_clk;
+
+	xdev->chan.direction = dma_dir;
+
+	if (xdev->chan.direction == DMA_DEV_TO_MEM) {
+		xdev->common.directions = BIT(DMA_DEV_TO_MEM);
+		dev_info(&pdev->dev, "Xilinx AXI frmbuf DMA_DEV_TO_MEM\n");
+	} else if (xdev->chan.direction == DMA_MEM_TO_DEV) {
+		xdev->common.directions = BIT(DMA_MEM_TO_DEV);
+		dev_info(&pdev->dev, "Xilinx AXI frmbuf DMA_MEM_TO_DEV\n");
+	} else {
+		err = -EINVAL;
+		goto remove_chan;
+	}
+
+	/* read supported video formats and update internal table */
+	hw_vid_fmt_cnt = of_property_count_strings(node, "xlnx,vid-formats");
+
+	err = of_property_read_string_array(node, "xlnx,vid-formats",
+					    vid_fmts, hw_vid_fmt_cnt);
+	if (err < 0) {
+		dev_err(&pdev->dev,
+			"Missing or invalid xlnx,vid-formats dts prop\n");
+		goto remove_chan;
+	}
+
+	for (i = 0; i < hw_vid_fmt_cnt; i++) {
+		const char *vid_fmt_name = vid_fmts[i];
+
+		for (j = 0; j < ARRAY_SIZE(xilinx_frmbuf_formats); j++) {
+			const char *dts_name =
+				xilinx_frmbuf_formats[j].dts_name;
+
+			if (strcmp(vid_fmt_name, dts_name))
+				continue;
+
+			xdev->enabled_vid_fmts |=
+				xilinx_frmbuf_formats[j].fmt_bitmask;
+		}
+	}
+
+	/* Determine supported vid framework formats */
+	frmbuf_init_format_array(xdev);
+
+	xdev->common.device_alloc_chan_resources =
+				xilinx_frmbuf_alloc_chan_resources;
+	xdev->common.device_free_chan_resources =
+				xilinx_frmbuf_free_chan_resources;
+	xdev->common.device_prep_interleaved_dma =
+				xilinx_frmbuf_dma_prep_interleaved;
+	xdev->common.device_terminate_all = xilinx_frmbuf_terminate_all;
+	xdev->common.device_synchronize = xilinx_frmbuf_synchronize;
+	xdev->common.device_tx_status = xilinx_frmbuf_tx_status;
+	xdev->common.device_issue_pending = xilinx_frmbuf_issue_pending;
+
+	platform_set_drvdata(pdev, xdev);
+
+	/* Register the DMA engine with the core */
+	dma_async_device_register(&xdev->common);
+
+	err = of_dma_controller_register(node, of_dma_xilinx_xlate, xdev);
+	if (err < 0) {
+		dev_err(&pdev->dev, "Unable to register DMA to DT\n");
+		goto error;
+	}
+
+	dev_info(&pdev->dev, "Xilinx AXI FrameBuffer Engine Driver Probed!!\n");
+
+	return 0;
+error:
+	dma_async_device_unregister(&xdev->common);
+remove_chan:
+	xilinx_frmbuf_chan_remove(&xdev->chan);
+disable_clk:
+	clk_disable_unprepare(xdev->ap_clk);
+	return err;
+}
+
+/**
+ * xilinx_frmbuf_remove - Driver remove function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * Return: Always '0'
+ */
+static int xilinx_frmbuf_remove(struct platform_device *pdev)
+{
+	struct xilinx_frmbuf_device *xdev = platform_get_drvdata(pdev);
+
+	of_dma_controller_free(pdev->dev.of_node);
+
+	dma_async_device_unregister(&xdev->common);
+	xilinx_frmbuf_chan_remove(&xdev->chan);
+	clk_disable_unprepare(xdev->ap_clk);
+
+	return 0;
+}
+
+MODULE_DEVICE_TABLE(of, xilinx_frmbuf_of_ids);
+
+static struct platform_driver xilinx_frmbuf_driver = {
+	.driver = {
+		.name = "xilinx-frmbuf",
+		.of_match_table = xilinx_frmbuf_of_ids,
+	},
+	.probe = xilinx_frmbuf_probe,
+	.remove = xilinx_frmbuf_remove,
+};
+
+module_platform_driver(xilinx_frmbuf_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx Framebuffer driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/dma/xilinx/zynqmp_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/dma/xilinx/zynqmp_dma.c
@@ -232,7 +232,7 @@
 	bool is_dmacoherent;
 	struct tasklet_struct tasklet;
 	bool idle;
-	u32 desc_size;
+	size_t desc_size;
 	bool err;
 	u32 bus_width;
 	u32 src_burst_len;
@@ -453,6 +453,7 @@
 
 	list_for_each_entry_safe(desc, next, list, node)
 		zynqmp_dma_free_descriptor(chan, desc);
+	INIT_LIST_HEAD(list);
 }
 
 /**
@@ -489,7 +490,8 @@
 	}
 
 	chan->desc_pool_v = dma_alloc_coherent(chan->dev,
-					       (2 * chan->desc_size * ZYNQMP_DMA_NUM_DESCS),
+					       (2 * ZYNQMP_DMA_DESC_SIZE(chan) *
+					       ZYNQMP_DMA_NUM_DESCS),
 					       &chan->desc_pool_p, GFP_KERNEL);
 	if (!chan->desc_pool_v)
 		return -ENOMEM;
@@ -500,7 +502,8 @@
 					(i * ZYNQMP_DMA_DESC_SIZE(chan) * 2));
 		desc->dst_v = (struct zynqmp_dma_desc_ll *) (desc->src_v + 1);
 		desc->src_p = chan->desc_pool_p +
-				(i * ZYNQMP_DMA_DESC_SIZE(chan) * 2);
+				((dma_addr_t)i * ZYNQMP_DMA_DESC_SIZE(chan)
+				 * 2);
 		desc->dst_p = desc->src_p + ZYNQMP_DMA_DESC_SIZE(chan);
 	}
 
@@ -845,7 +848,7 @@
 
 	zynqmp_dma_desc_config_eod(chan, desc);
 	async_tx_ack(&first->async_tx);
-	first->async_tx.flags = flags;
+	first->async_tx.flags = (enum dma_ctrl_flags)flags;
 	return &first->async_tx;
 }
 
@@ -1076,7 +1079,11 @@
 	pm_runtime_set_autosuspend_delay(zdev->dev, ZDMA_PM_TIMEOUT);
 	pm_runtime_use_autosuspend(zdev->dev);
 	pm_runtime_enable(zdev->dev);
-	pm_runtime_get_sync(zdev->dev);
+	ret = pm_runtime_get_sync(zdev->dev);
+	if (ret < 0) {
+		dev_err(zdev->dev, "pm_runtime_get_sync() failed\n");
+		pm_runtime_disable(zdev->dev);
+	}
 	if (!pm_runtime_enabled(zdev->dev)) {
 		ret = zynqmp_dma_runtime_resume(zdev->dev);
 		if (ret)
@@ -1092,7 +1099,11 @@
 	p->dst_addr_widths = BIT(zdev->chan->bus_width / 8);
 	p->src_addr_widths = BIT(zdev->chan->bus_width / 8);
 
-	dma_async_device_register(&zdev->common);
+	ret = dma_async_device_register(&zdev->common);
+	if (ret) {
+		dev_err(zdev->dev, "failed to register the dma device\n");
+		goto free_chan_resources;
+	}
 
 	ret = of_dma_controller_register(pdev->dev.of_node,
 					 of_zynqmp_dma_xlate, zdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/Kconfig
@@ -343,6 +343,13 @@
 	  a companion chip to the PowerPC 970 family of
 	  processors.
 
+config EDAC_PL310_L2
+	tristate "Pl310 L2 Cache Controller"
+	depends on ARM
+	help
+	  Support for parity error detection on L2 cache controller
+	  data and tag ram memory
+
 config EDAC_HIGHBANK_MC
 	tristate "Highbank Memory Controller"
 	depends on ARCH_HIGHBANK
@@ -489,6 +496,13 @@
 	  Support for error detection and correction on the Synopsys DDR
 	  memory controller.
 
+config EDAC_ZYNQMP_OCM
+	tristate "Xilinx ZynqMP OCM Controller"
+	depends on ARCH_ZYNQMP
+	help
+	  Support for error detection and correction on the xilinx ZynqMP OCM
+	  controller.
+
 config EDAC_XGENE
 	tristate "APM X-Gene SoC"
 	depends on (ARM64 || COMPILE_TEST)
@@ -496,6 +510,14 @@
 	  Support for error detection and correction on the
 	  APM X-Gene family of SOCs.
 
+config EDAC_CORTEX_ARM64
+	tristate "ARM Cortex A57/A53"
+	default y if !CPU_IDLE
+	depends on !CPU_IDLE && ARM64
+	help
+	  Support for error detection and correction on the
+	  ARM Cortex A57 and A53.
+
 config EDAC_TI
 	tristate "Texas Instruments DDR3 ECC Controller"
 	depends on ARCH_KEYSTONE || SOC_DRA7XX
@@ -539,4 +561,15 @@
 	  Support for error detection and correction on the
 	  SoCs with ARM DMC-520 DRAM controller.
 
+config EDAC_XILINX_DDR
+	tristate "Xilinx Versal DDR Memory Controller"
+	depends on ARCH_ZYNQMP
+	help
+	  Support for error detection and correction on the Xilinx Versal DDR
+	  memory controller.
+
+	  Report both Single Bit Errors (CE) and Double Bit Errors (UE).
+	  Support injecting both Correctable and UnCorrectable errors for debug
+	  purpose using sysfs entries.
+
 endif # EDAC
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/Makefile
@@ -54,11 +54,13 @@
 layerscape_edac_mod-y			:= fsl_ddr_edac.o layerscape_edac.o
 obj-$(CONFIG_EDAC_LAYERSCAPE)		+= layerscape_edac_mod.o
 
-skx_edac-y				:= skx_common.o skx_base.o
-obj-$(CONFIG_EDAC_SKX)			+= skx_edac.o
+skx_edac_common-y			:= skx_common.o
 
-i10nm_edac-y				:= skx_common.o i10nm_base.o
-obj-$(CONFIG_EDAC_I10NM)		+= i10nm_edac.o
+skx_edac-y				:= skx_base.o
+obj-$(CONFIG_EDAC_SKX)			+= skx_edac.o skx_edac_common.o
+
+i10nm_edac-y				:= i10nm_base.o
+obj-$(CONFIG_EDAC_I10NM)		+= i10nm_edac.o skx_edac_common.o
 
 obj-$(CONFIG_EDAC_CELL)			+= cell_edac.o
 obj-$(CONFIG_EDAC_PPC4XX)		+= ppc4xx_edac.o
@@ -75,12 +77,16 @@
 obj-$(CONFIG_EDAC_THUNDERX)		+= thunderx_edac.o
 
 obj-$(CONFIG_EDAC_ALTERA)		+= altera_edac.o
+obj-$(CONFIG_EDAC_PL310_L2)		+= pl310_edac_l2.o
 obj-$(CONFIG_EDAC_SIFIVE)		+= sifive_edac.o
 obj-$(CONFIG_EDAC_ARMADA_XP)		+= armada_xp_edac.o
 obj-$(CONFIG_EDAC_SYNOPSYS)		+= synopsys_edac.o
 obj-$(CONFIG_EDAC_XGENE)		+= xgene_edac.o
+obj-$(CONFIG_EDAC_CORTEX_ARM64)		+= cortex_arm64_edac.o
+obj-$(CONFIG_EDAC_ZYNQMP_OCM)		+= zynqmp_ocm_edac.o
 obj-$(CONFIG_EDAC_TI)			+= ti_edac.o
 obj-$(CONFIG_EDAC_QCOM)			+= qcom_edac.o
 obj-$(CONFIG_EDAC_ASPEED)		+= aspeed_edac.o
 obj-$(CONFIG_EDAC_BLUEFIELD)		+= bluefield_edac.o
+obj-$(CONFIG_EDAC_XILINX_DDR)		+= xilinx_ddrmc_edac.o
 obj-$(CONFIG_EDAC_DMC520)		+= dmc520_edac.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/altera_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/altera_edac.c
@@ -350,7 +350,7 @@
 	if (irq < 0) {
 		edac_printk(KERN_ERR, EDAC_MC,
 			    "No irq %d in DT\n", irq);
-		return -ENODEV;
+		return irq;
 	}
 
 	/* Arria10 has a 2nd IRQ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/amd64_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/amd64_edac.c
@@ -1065,12 +1065,14 @@
 #define CS_ODD_PRIMARY		BIT(1)
 #define CS_EVEN_SECONDARY	BIT(2)
 #define CS_ODD_SECONDARY	BIT(3)
+#define CS_3R_INTERLEAVE	BIT(4)
 
 #define CS_EVEN			(CS_EVEN_PRIMARY | CS_EVEN_SECONDARY)
 #define CS_ODD			(CS_ODD_PRIMARY | CS_ODD_SECONDARY)
 
 static int f17_get_cs_mode(int dimm, u8 ctrl, struct amd64_pvt *pvt)
 {
+	u8 base, count = 0;
 	int cs_mode = 0;
 
 	if (csrow_enabled(2 * dimm, ctrl, pvt))
@@ -1083,6 +1085,20 @@
 	if (csrow_sec_enabled(2 * dimm + 1, ctrl, pvt))
 		cs_mode |= CS_ODD_SECONDARY;
 
+	/*
+	 * 3 Rank inteleaving support.
+	 * There should be only three bases enabled and their two masks should
+	 * be equal.
+	 */
+	for_each_chip_select(base, ctrl, pvt)
+		count += csrow_enabled(base, ctrl, pvt);
+
+	if (count == 3 &&
+	    pvt->csels[ctrl].csmasks[0] == pvt->csels[ctrl].csmasks[1]) {
+		edac_dbg(1, "3R interleaving in use.\n");
+		cs_mode |= CS_3R_INTERLEAVE;
+	}
+
 	return cs_mode;
 }
 
@@ -1891,10 +1907,14 @@
 	 *
 	 * The MSB is the number of bits in the full mask because BIT[0] is
 	 * always 0.
+	 *
+	 * In the special 3 Rank interleaving case, a single bit is flipped
+	 * without swapping with the most significant bit. This can be handled
+	 * by keeping the MSB where it is and ignoring the single zero bit.
 	 */
 	msb = fls(addr_mask_orig) - 1;
 	weight = hweight_long(addr_mask_orig);
-	num_zero_bits = msb - weight;
+	num_zero_bits = msb - weight - !!(cs_mode & CS_3R_INTERLEAVE);
 
 	/* Take the number of zero bits off from the top of the mask. */
 	addr_mask_deinterleaved = GENMASK_ULL(msb - num_zero_bits, 1);
@@ -2630,6 +2650,16 @@
 			.dbam_to_cs		= f17_addr_mask_to_cs_size,
 		}
 	},
+	[F19_M10H_CPUS] = {
+		.ctl_name = "F19h_M10h",
+		.f0_id = PCI_DEVICE_ID_AMD_19H_M10H_DF_F0,
+		.f6_id = PCI_DEVICE_ID_AMD_19H_M10H_DF_F6,
+		.max_mcs = 12,
+		.ops = {
+			.early_channel_count	= f17_early_channel_count,
+			.dbam_to_cs		= f17_addr_mask_to_cs_size,
+		}
+	},
 };
 
 /*
@@ -3667,11 +3697,20 @@
 		break;
 
 	case 0x19:
-		if (pvt->model >= 0x20 && pvt->model <= 0x2f) {
+		if (pvt->model >= 0x10 && pvt->model <= 0x1f) {
+			fam_type = &family_types[F19_M10H_CPUS];
+			pvt->ops = &family_types[F19_M10H_CPUS].ops;
+			break;
+		} else if (pvt->model >= 0x20 && pvt->model <= 0x2f) {
 			fam_type = &family_types[F17_M70H_CPUS];
 			pvt->ops = &family_types[F17_M70H_CPUS].ops;
 			fam_type->ctl_name = "F19h_M20h";
 			break;
+		} else if (pvt->model >= 0xa0 && pvt->model <= 0xaf) {
+			fam_type = &family_types[F19_M10H_CPUS];
+			pvt->ops = &family_types[F19_M10H_CPUS].ops;
+			fam_type->ctl_name = "F19h_MA0h";
+			break;
 		}
 		fam_type	= &family_types[F19_CPUS];
 		pvt->ops	= &family_types[F19_CPUS].ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/amd64_edac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/amd64_edac.h
@@ -96,7 +96,7 @@
 /* Hardware limit on ChipSelect rows per MC and processors per system */
 #define NUM_CHIPSELECTS			8
 #define DRAM_RANGES			8
-#define NUM_CONTROLLERS			8
+#define NUM_CONTROLLERS			12
 
 #define ON true
 #define OFF false
@@ -126,6 +126,8 @@
 #define PCI_DEVICE_ID_AMD_17H_M70H_DF_F6 0x1446
 #define PCI_DEVICE_ID_AMD_19H_DF_F0	0x1650
 #define PCI_DEVICE_ID_AMD_19H_DF_F6	0x1656
+#define PCI_DEVICE_ID_AMD_19H_M10H_DF_F0 0x14ad
+#define PCI_DEVICE_ID_AMD_19H_M10H_DF_F6 0x14b3
 
 /*
  * Function 1 - Address Map
@@ -298,6 +300,7 @@
 	F17_M60H_CPUS,
 	F17_M70H_CPUS,
 	F19_CPUS,
+	F19_M10H_CPUS,
 	NUM_FAMILIES,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/bluefield_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/bluefield_edac.c
@@ -180,7 +180,7 @@
 static void bluefield_edac_init_dimms(struct mem_ctl_info *mci)
 {
 	struct bluefield_edac_priv *priv = mci->pvt_info;
-	int mem_ctrl_idx = mci->mc_idx;
+	u64 mem_ctrl_idx = mci->mc_idx;
 	struct dimm_info *dimm;
 	u64 smc_info, smc_arg;
 	int is_empty = 1, i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/cortex_arm64_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/cortex_arm64_edac.c
@@ -0,0 +1,471 @@
+/*
+ * Cortex A57 and A53 EDAC
+ *
+ * Copyright (c) 2015, Advanced Micro Devices
+ * Author: Brijesh Singh <brijeshkumar.singh@amd.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <ras/ras_event.h>
+
+#include "edac_module.h"
+
+#define DRV_NAME			"cortex_edac"
+
+#define CPUMERRSR_EL1_INDEX(x, y)	((x) & (y))
+#define CPUMERRSR_EL1_BANK_WAY(x, y)	(((x) >> 18) & (y))
+#define CPUMERRSR_EL1_RAMID(x)		(((x) >> 24) & 0x7f)
+#define CPUMERRSR_EL1_VALID(x)		((x) & (1 << 31))
+#define CPUMERRSR_EL1_REPEAT(x)		(((x) >> 32) & 0x7f)
+#define CPUMERRSR_EL1_OTHER(x)		(((x) >> 40) & 0xff)
+#define CPUMERRSR_EL1_FATAL(x)		((x) & (1UL << 63))
+#define L1_I_TAG_RAM			0x00
+#define L1_I_DATA_RAM			0x01
+#define L1_D_TAG_RAM			0x08
+#define L1_D_DATA_RAM			0x09
+#define L1_D_DIRTY_RAM			0x14
+#define TLB_RAM				0x18
+
+#define L2MERRSR_EL1_CPUID_WAY(x)	(((x) >> 18) & 0xf)
+#define L2MERRSR_EL1_RAMID(x)		(((x) >> 24) & 0x7f)
+#define L2MERRSR_EL1_VALID(x)		((x) & (1 << 31))
+#define L2MERRSR_EL1_REPEAT(x)		(((x) >> 32) & 0xff)
+#define L2MERRSR_EL1_OTHER(x)		(((x) >> 40) & 0xff)
+#define L2MERRSR_EL1_FATAL(x)		((x) & (1UL << 63))
+#define L2_TAG_RAM			0x10
+#define L2_DATA_RAM			0x11
+#define L2_SNOOP_RAM			0x12
+#define L2_DIRTY_RAM			0x14
+#define L2_INCLUSION_PF_RAM		0x18
+
+#define L1_CACHE			0
+#define L2_CACHE			1
+
+#define EDAC_MOD_STR			DRV_NAME
+
+/* Error injectin macros*/
+#define L1_DCACHE_ERRINJ_ENABLE		(1 << 6)
+#define L1_DCACHE_ERRINJ_DISABLE	(~(1 << 6))
+#define L2_DCACHE_ERRINJ_ENABLE		(1 << 29)
+#define L2_DCACHE_ERRINJ_DISABLE	(~(1 << 29))
+#define L2_ECC_PROTECTION		(1 << 22)
+
+static int poll_msec = 100;
+
+struct cortex_arm64_edac {
+	struct edac_device_ctl_info *edac_ctl;
+};
+
+static inline u64 read_cpumerrsr_el1(void)
+{
+	u64 val;
+
+	asm volatile("mrs %0, s3_1_c15_c2_2" : "=r" (val));
+	return val;
+}
+
+static inline void write_cpumerrsr_el1(u64 val)
+{
+	asm volatile("msr s3_1_c15_c2_2, %0" :: "r" (val));
+}
+
+static inline u64 read_l2merrsr_el1(void)
+{
+	u64 val;
+
+	asm volatile("mrs %0, s3_1_c15_c2_3" : "=r" (val));
+	return val;
+}
+
+static inline void write_l2merrsr_el1(u64 val)
+{
+	asm volatile("msr s3_1_c15_c2_3, %0" :: "r" (val));
+}
+
+static inline void cortexa53_edac_busy_on_inst(void)
+{
+	asm volatile("isb sy");
+}
+
+static inline void cortexa53_edac_busy_on_data(void)
+{
+	asm volatile("dsb sy");
+}
+
+static inline void write_l2actrl_el1(u64 val)
+{
+	asm volatile("msr s3_1_c15_c0_0, %0" :: "r" (val));
+	cortexa53_edac_busy_on_inst();
+}
+
+static inline u64 read_l2actrl_el1(void)
+{
+	u64 val;
+
+	asm volatile("mrs %0, s3_1_c15_c0_0" : "=r" (val));
+	return val;
+}
+
+static inline u64 read_l2ctlr_el1(void)
+{
+	u64 rval;
+
+	asm volatile("mrs %0,  S3_1_C11_C0_2" : "=r" (rval));
+	return rval;
+
+}
+
+static inline u64 read_l1actrl_el1(void)
+{
+	u64 rval;
+
+	asm volatile("mrs %0,  S3_1_C15_C2_0" : "=r" (rval));
+	return rval;
+}
+
+static inline void write_l1actrl_el1(u64 val)
+{
+	asm volatile("msr S3_1_C15_C2_0, %0" :: "r" (val));
+}
+
+static void parse_cpumerrsr(void *arg)
+{
+	int cpu, partnum, way;
+	unsigned int index = 0;
+	u64 val = read_cpumerrsr_el1();
+	int repeat_err, other_err;
+
+	/* we do not support fatal error handling so far */
+	if (CPUMERRSR_EL1_FATAL(val))
+		return;
+
+	/* check if we have valid error before continuing */
+	if (!CPUMERRSR_EL1_VALID(val))
+		return;
+
+	cpu = smp_processor_id();
+	partnum = read_cpuid_part_number();
+	repeat_err = CPUMERRSR_EL1_REPEAT(val);
+	other_err = CPUMERRSR_EL1_OTHER(val);
+
+	/* way/bank and index address bit ranges are different between
+	 * A57 and A53 */
+	if (partnum == ARM_CPU_PART_CORTEX_A57) {
+		index = CPUMERRSR_EL1_INDEX(val, 0x1ffff);
+		way = CPUMERRSR_EL1_BANK_WAY(val, 0x1f);
+	} else {
+		index = CPUMERRSR_EL1_INDEX(val, 0xfff);
+		way = CPUMERRSR_EL1_BANK_WAY(val, 0x7);
+	}
+
+	edac_printk(KERN_CRIT, EDAC_MOD_STR, "CPU%d L1 error detected!\n", cpu);
+	edac_printk(KERN_CRIT, EDAC_MOD_STR, "index=%#x, RAMID=", index);
+
+	switch (CPUMERRSR_EL1_RAMID(val)) {
+	case L1_I_TAG_RAM:
+		pr_cont("'L1-I Tag RAM' (way %d)", way);
+		break;
+	case L1_I_DATA_RAM:
+		pr_cont("'L1-I Data RAM' (bank %d)", way);
+		break;
+	case L1_D_TAG_RAM:
+		pr_cont("'L1-D Tag RAM' (way %d)", way);
+		break;
+	case L1_D_DATA_RAM:
+		pr_cont("'L1-D Data RAM' (bank %d)", way);
+		break;
+	case L1_D_DIRTY_RAM:
+		pr_cont("'L1 Dirty RAM'");
+		break;
+	case TLB_RAM:
+		pr_cont("'TLB RAM'");
+		break;
+	default:
+		pr_cont("'unknown'");
+		break;
+	}
+
+	pr_cont(", repeat=%d, other=%d (CPUMERRSR_EL1=%#llx)\n", repeat_err,
+		other_err, val);
+
+	trace_mc_event(HW_EVENT_ERR_CORRECTED, "L1 non-fatal error",
+		       "", repeat_err, 0, 0, 0, -1, index, 0, 0, DRV_NAME);
+	write_cpumerrsr_el1(0);
+}
+
+static void a57_parse_l2merrsr_way(u8 ramid, u8 val)
+{
+	switch (ramid) {
+	case L2_TAG_RAM:
+	case L2_DATA_RAM:
+	case L2_DIRTY_RAM:
+		pr_cont("(cpu%d tag, way %d)", val / 2, val % 2);
+		break;
+	case L2_SNOOP_RAM:
+		pr_cont("(cpu%d tag, way %d)", (val & 0x6) >> 1,
+			(val & 0x1));
+		break;
+	}
+}
+
+static void a53_parse_l2merrsr_way(u8 ramid, u8 val)
+{
+	switch (ramid) {
+	case L2_TAG_RAM:
+		pr_cont("(way %d)", val);
+		fallthrough;
+	case L2_DATA_RAM:
+		pr_cont("(bank %d)", val);
+		break;
+	case L2_SNOOP_RAM:
+		pr_cont("(cpu%d tag, way %d)", val / 2, val % 4);
+		break;
+	}
+}
+
+static void parse_l2merrsr(void *arg)
+{
+	int cpu, partnum;
+	unsigned int index;
+	int repeat_err, other_err;
+	u64 val = read_l2merrsr_el1();
+
+	/* we do not support fatal error handling so far */
+	if (L2MERRSR_EL1_FATAL(val))
+		return;
+
+	/* check if we have valid error before continuing */
+	if (!L2MERRSR_EL1_VALID(val))
+		return;
+
+	cpu = smp_processor_id();
+	partnum = read_cpuid_part_number();
+	repeat_err = L2MERRSR_EL1_REPEAT(val);
+	other_err = L2MERRSR_EL1_OTHER(val);
+
+	/* index address range is different between A57 and A53 */
+	if (partnum == ARM_CPU_PART_CORTEX_A57)
+		index = val & 0x1ffff;
+	else
+		index = (val >> 3) & 0x3fff;
+
+	edac_printk(KERN_CRIT, EDAC_MOD_STR, "CPU%d L2 error detected!\n", cpu);
+	edac_printk(KERN_CRIT, EDAC_MOD_STR, "index=%#x RAMID=", index);
+
+	switch (L2MERRSR_EL1_RAMID(val)) {
+	case L2_TAG_RAM:
+		pr_cont("'L2 Tag RAM'");
+		break;
+	case L2_DATA_RAM:
+		pr_cont("'L2 Data RAM'");
+		break;
+	case L2_SNOOP_RAM:
+		pr_cont("'L2 Snoop tag RAM'");
+		break;
+	case L2_DIRTY_RAM:
+		pr_cont("'L2 Dirty RAM'");
+		break;
+	case L2_INCLUSION_PF_RAM:
+		pr_cont("'L2 inclusion PF RAM'");
+		break;
+	default:
+		pr_cont("unknown");
+		break;
+	}
+
+	/* cpuid/way bit description is different between A57 and A53 */
+	if (partnum == ARM_CPU_PART_CORTEX_A57)
+		a57_parse_l2merrsr_way(L2MERRSR_EL1_RAMID(val),
+				       L2MERRSR_EL1_CPUID_WAY(val));
+	else
+		a53_parse_l2merrsr_way(L2MERRSR_EL1_RAMID(val),
+				       L2MERRSR_EL1_CPUID_WAY(val));
+
+	pr_cont(", repeat=%d, other=%d (L2MERRSR_EL1=%#llx)\n", repeat_err,
+		other_err, val);
+	trace_mc_event(HW_EVENT_ERR_CORRECTED, "L2 non-fatal error",
+		       "", repeat_err, 0, 0, 0, -1, index, 0, 0, DRV_NAME);
+	write_l2merrsr_el1(0);
+}
+
+static void cortex_arm64_edac_check(struct edac_device_ctl_info *edac_ctl)
+{
+	int cpu;
+	struct cpumask cluster_mask, old_mask;
+
+	cpumask_clear(&cluster_mask);
+	cpumask_clear(&old_mask);
+
+	cpus_read_lock();
+	for_each_online_cpu(cpu) {
+		/* Check CPU L1 error */
+		smp_call_function_single(cpu, parse_cpumerrsr, NULL, 0);
+		cpumask_copy(&cluster_mask, topology_core_cpumask(cpu));
+		if (cpumask_equal(&cluster_mask, &old_mask))
+			continue;
+		cpumask_copy(&old_mask, &cluster_mask);
+		/* Check CPU L2 error */
+		smp_call_function_any(&cluster_mask, parse_l2merrsr, NULL, 0);
+	}
+	cpus_read_unlock();
+}
+
+static ssize_t cortexa53_edac_inject_L2_show(struct edac_device_ctl_info
+							*dci, char *data)
+{
+	return sprintf(data, "L2ACTLR_EL1: [0x%llx]\n\r", read_l2actrl_el1());
+}
+
+static ssize_t cortexa53_edac_inject_L2_store(
+		struct edac_device_ctl_info *dci, const char *data,
+		size_t count)
+{
+	u64 l2actrl, l2ecc;
+
+	if (!data)
+		return -EFAULT;
+
+	l2ecc = read_l2ctlr_el1();
+	if ((l2ecc & L2_ECC_PROTECTION)) {
+		l2actrl = read_l2actrl_el1();
+		l2actrl = l2actrl | L2_DCACHE_ERRINJ_ENABLE;
+		write_l2actrl_el1(l2actrl);
+		cortexa53_edac_busy_on_inst();
+	} else {
+		edac_printk(KERN_CRIT, EDAC_MOD_STR, "L2 ECC not enabled\n");
+	}
+
+	return count;
+}
+
+static ssize_t cortexa53_edac_inject_L1_show(struct edac_device_ctl_info
+							*dci, char *data)
+{
+	return sprintf(data, "L1CTLR_EL1: [0x%llx]\n\r", read_l1actrl_el1());
+}
+
+static ssize_t cortexa53_edac_inject_L1_store(
+		struct edac_device_ctl_info *dci, const char *data,
+		size_t count)
+{
+	u64 l1actrl;
+
+	if (!data)
+		return -EFAULT;
+
+	l1actrl = read_l1actrl_el1();
+	l1actrl |= L1_DCACHE_ERRINJ_ENABLE;
+	write_l1actrl_el1(l1actrl);
+	cortexa53_edac_busy_on_inst();
+
+	return count;
+}
+
+static struct edac_dev_sysfs_attribute cortexa53_edac_sysfs_attributes[] = {
+	{
+		.attr = {
+			.name = "inject_L2_Cache_Error",
+			.mode = (S_IRUGO | S_IWUSR)
+		},
+		.show = cortexa53_edac_inject_L2_show,
+		.store = cortexa53_edac_inject_L2_store},
+	{
+		.attr = {
+			.name = "inject_L1_Cache_Error",
+			.mode = (S_IRUGO | S_IWUSR)
+		},
+		.show = cortexa53_edac_inject_L1_show,
+		.store = cortexa53_edac_inject_L1_store},
+
+	/* End of list */
+	{
+		.attr = {.name = NULL}
+	}
+};
+
+static void cortexa53_set_edac_sysfs_attributes(struct edac_device_ctl_info
+						*edac_dev)
+{
+	edac_dev->sysfs_attributes = cortexa53_edac_sysfs_attributes;
+}
+
+static int cortex_arm64_edac_probe(struct platform_device *pdev)
+{
+	int rc;
+	struct cortex_arm64_edac *drv;
+	struct device *dev = &pdev->dev;
+
+	drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
+	if (!drv)
+		return -ENOMEM;
+
+	/* Only POLL mode is supported */
+	edac_op_state = EDAC_OPSTATE_POLL;
+
+	drv->edac_ctl = edac_device_alloc_ctl_info(0, "cpu_cache", 1, "L", 2,
+						   0, NULL, 0,
+						   edac_device_alloc_index());
+	if (IS_ERR(drv->edac_ctl))
+		return -ENOMEM;
+
+	drv->edac_ctl->poll_msec = poll_msec;
+	drv->edac_ctl->edac_check = cortex_arm64_edac_check;
+	drv->edac_ctl->dev = dev;
+	drv->edac_ctl->mod_name = dev_name(dev);
+	drv->edac_ctl->dev_name = dev_name(dev);
+	drv->edac_ctl->ctl_name = "cache_err";
+	platform_set_drvdata(pdev, drv);
+
+	cortexa53_set_edac_sysfs_attributes(drv->edac_ctl);
+
+	rc = edac_device_add_device(drv->edac_ctl);
+	if (rc)
+		edac_device_free_ctl_info(drv->edac_ctl);
+
+	return rc;
+}
+
+static int cortex_arm64_edac_remove(struct platform_device *pdev)
+{
+	struct cortex_arm64_edac *drv = dev_get_drvdata(&pdev->dev);
+	struct edac_device_ctl_info *edac_ctl = drv->edac_ctl;
+
+	edac_device_del_device(edac_ctl->dev);
+	edac_device_free_ctl_info(edac_ctl);
+
+	return 0;
+}
+
+static const struct of_device_id cortex_arm64_edac_of_match[] = {
+	{ .compatible = "arm,cortex-a57-edac" },
+	{ .compatible = "arm,cortex-a53-edac" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, cortex_arm64_edac_of_match);
+
+static struct platform_driver cortex_arm64_edac_driver = {
+	.probe = cortex_arm64_edac_probe,
+	.remove = cortex_arm64_edac_remove,
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table = cortex_arm64_edac_of_match,
+	},
+};
+module_platform_driver(cortex_arm64_edac_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Brijesh Singh <brijeshkumar.singh@amd.com>");
+MODULE_DESCRIPTION("Cortex A57 and A53 EDAC driver");
+module_param(poll_msec, int, 0444);
+MODULE_PARM_DESC(poll_msec, "EDAC monitor poll interval in msec");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/dmc520_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/dmc520_edac.c
@@ -489,7 +489,7 @@
 	dev = &pdev->dev;
 
 	for (idx = 0; idx < NUMBER_OF_IRQS; idx++) {
-		irq = platform_get_irq_byname(pdev, dmc520_irq_configs[idx].name);
+		irq = platform_get_irq_byname_optional(pdev, dmc520_irq_configs[idx].name);
 		irqs[idx] = irq;
 		masks[idx] = dmc520_irq_configs[idx].mask;
 		if (irq >= 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/edac_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/edac_device.c
@@ -34,6 +34,9 @@
 static DEFINE_MUTEX(device_ctls_mutex);
 static LIST_HEAD(edac_device_list);
 
+/* Default workqueue processing interval on this instance, in msecs */
+#define DEFAULT_POLL_INTERVAL 1000
+
 #ifdef CONFIG_EDAC_DEBUG
 static void edac_device_dump_device(struct edac_device_ctl_info *edac_dev)
 {
@@ -366,7 +369,7 @@
 	 * whole one second to save timers firing all over the period
 	 * between integral seconds
 	 */
-	if (edac_dev->poll_msec == 1000)
+	if (edac_dev->poll_msec == DEFAULT_POLL_INTERVAL)
 		edac_queue_work(&edac_dev->work, round_jiffies_relative(edac_dev->delay));
 	else
 		edac_queue_work(&edac_dev->work, edac_dev->delay);
@@ -396,7 +399,7 @@
 	 * timers firing on sub-second basis, while they are happy
 	 * to fire together on the 1 second exactly
 	 */
-	if (edac_dev->poll_msec == 1000)
+	if (edac_dev->poll_msec == DEFAULT_POLL_INTERVAL)
 		edac_queue_work(&edac_dev->work, round_jiffies_relative(edac_dev->delay));
 	else
 		edac_queue_work(&edac_dev->work, edac_dev->delay);
@@ -424,17 +427,16 @@
  *	Then restart the workq on the new delay
  */
 void edac_device_reset_delay_period(struct edac_device_ctl_info *edac_dev,
-					unsigned long value)
+				    unsigned long msec)
 {
-	unsigned long jiffs = msecs_to_jiffies(value);
-
-	if (value == 1000)
-		jiffs = round_jiffies_relative(value);
-
-	edac_dev->poll_msec = value;
-	edac_dev->delay	    = jiffs;
+	edac_dev->poll_msec = msec;
+	edac_dev->delay	    = msecs_to_jiffies(msec);
 
-	edac_mod_work(&edac_dev->work, jiffs);
+	/* See comment in edac_device_workq_setup() above */
+	if (edac_dev->poll_msec == DEFAULT_POLL_INTERVAL)
+		edac_mod_work(&edac_dev->work, round_jiffies_relative(edac_dev->delay));
+	else
+		edac_mod_work(&edac_dev->work, edac_dev->delay);
 }
 
 int edac_device_alloc_index(void)
@@ -473,11 +475,7 @@
 		/* This instance is NOW RUNNING */
 		edac_dev->op_state = OP_RUNNING_POLL;
 
-		/*
-		 * enable workq processing on this instance,
-		 * default = 1000 msec
-		 */
-		edac_device_workq_setup(edac_dev, 1000);
+		edac_device_workq_setup(edac_dev, edac_dev->poll_msec ?: DEFAULT_POLL_INTERVAL);
 	} else {
 		edac_dev->op_state = OP_RUNNING_INTERRUPT;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/edac_mc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/edac_mc.c
@@ -164,6 +164,8 @@
 	[MEM_LPDDR4]	= "Low-Power-DDR4-RAM",
 	[MEM_LRDDR4]	= "Load-Reduced-DDR4-RAM",
 	[MEM_DDR5]	= "Unbuffered-DDR5",
+	[MEM_RDDR5]	= "Registered-DDR5",
+	[MEM_LRDDR5]	= "Load-Reduced-DDR5-RAM",
 	[MEM_NVDIMM]	= "Non-volatile-RAM",
 	[MEM_WIO2]	= "Wide-IO-2",
 	[MEM_HBM2]	= "High-bandwidth-memory-Gen2",
@@ -215,7 +217,7 @@
 	else
 		return (char *)ptr;
 
-	r = (unsigned long)p % align;
+	r = (unsigned long)ptr % align;
 
 	if (r == 0)
 		return (char *)ptr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/edac_module.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/edac_module.h
@@ -56,7 +56,7 @@
 bool edac_mod_work(struct delayed_work *work, unsigned long delay);
 
 extern void edac_device_reset_delay_period(struct edac_device_ctl_info
-					   *edac_dev, unsigned long value);
+					   *edac_dev, unsigned long msec);
 extern void edac_mc_reset_delay_period(unsigned long value);
 
 extern void *edac_align_ptr(void **p, unsigned size, int n_elems);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/fsl_ddr_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/fsl_ddr_edac.c
@@ -331,21 +331,25 @@
 	 * TODO: Add support for 32-bit wide buses
 	 */
 	if ((err_detect & DDR_EDE_SBE) && (bus_width == 64)) {
+		u64 cap = (u64)cap_high << 32 | cap_low;
+		u32 s = syndrome;
+
 		sbe_ecc_decode(cap_high, cap_low, syndrome,
 				&bad_data_bit, &bad_ecc_bit);
 
-		if (bad_data_bit != -1)
-			fsl_mc_printk(mci, KERN_ERR,
-				"Faulty Data bit: %d\n", bad_data_bit);
-		if (bad_ecc_bit != -1)
-			fsl_mc_printk(mci, KERN_ERR,
-				"Faulty ECC bit: %d\n", bad_ecc_bit);
+		if (bad_data_bit >= 0) {
+			fsl_mc_printk(mci, KERN_ERR, "Faulty Data bit: %d\n", bad_data_bit);
+			cap ^= 1ULL << bad_data_bit;
+		}
+
+		if (bad_ecc_bit >= 0) {
+			fsl_mc_printk(mci, KERN_ERR, "Faulty ECC bit: %d\n", bad_ecc_bit);
+			s ^= 1 << bad_ecc_bit;
+		}
 
 		fsl_mc_printk(mci, KERN_ERR,
 			"Expected Data / ECC:\t%#8.8x_%08x / %#2.2x\n",
-			cap_high ^ (1 << (bad_data_bit - 32)),
-			cap_low ^ (1 << bad_data_bit),
-			syndrome ^ (1 << bad_ecc_bit));
+			upper_32_bits(cap), lower_32_bits(cap), s);
 	}
 
 	fsl_mc_printk(mci, KERN_ERR,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/ghes_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/ghes_edac.c
@@ -101,9 +101,14 @@
 
 	dmi_memdev_name(handle, &bank, &device);
 
-	/* both strings must be non-zero */
-	if (bank && *bank && device && *device)
-		snprintf(dimm->label, sizeof(dimm->label), "%s %s", bank, device);
+	/*
+	 * Set to a NULL string when both bank and device are zero. In this case,
+	 * the label assigned by default will be preserved.
+	 */
+	snprintf(dimm->label, sizeof(dimm->label), "%s%s%s",
+		 (bank && *bank) ? bank : "",
+		 (bank && *bank && device && *device) ? " " : "",
+		 (device && *device) ? device : "");
 }
 
 static void assign_dmi_dimm_info(struct dimm_info *dimm, struct memdev_dmi_entry *entry)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/highbank_mc_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/highbank_mc_edac.c
@@ -174,8 +174,10 @@
 	drvdata = mci->pvt_info;
 	platform_set_drvdata(pdev, mci);
 
-	if (!devres_open_group(&pdev->dev, NULL, GFP_KERNEL))
-		return -ENOMEM;
+	if (!devres_open_group(&pdev->dev, NULL, GFP_KERNEL)) {
+		res = -ENOMEM;
+		goto free;
+	}
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!r) {
@@ -243,6 +245,7 @@
 	edac_mc_del_mc(&pdev->dev);
 err:
 	devres_release_group(&pdev->dev, NULL);
+free:
 	edac_mc_free(mci);
 	return res;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/i10nm_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/i10nm_base.c
@@ -198,11 +198,10 @@
 	if (unlikely(pci_enable_device(pdev) < 0)) {
 		edac_dbg(2, "Failed to enable device %02x:%02x.%x\n",
 			 bus, dev, fun);
+		pci_dev_put(pdev);
 		return NULL;
 	}
 
-	pci_dev_get(pdev);
-
 	return pdev;
 }
 
@@ -358,6 +357,9 @@
 
 			mbase = ioremap(base + off, I10NM_HBM_IMC_MMIO_SIZE);
 			if (!mbase) {
+				pci_dev_put(d->imc[lmc].mdev);
+				d->imc[lmc].mdev = NULL;
+
 				i10nm_printk(KERN_ERR, "Failed to ioremap for hbm mc 0x%llx\n",
 					     base + off);
 				return -ENOMEM;
@@ -368,6 +370,12 @@
 
 			mcmtr = I10NM_GET_MCMTR(&d->imc[lmc], 0);
 			if (!I10NM_IS_HBM_IMC(mcmtr)) {
+				iounmap(d->imc[lmc].mbase);
+				d->imc[lmc].mbase = NULL;
+				d->imc[lmc].hbm_mc = false;
+				pci_dev_put(d->imc[lmc].mdev);
+				d->imc[lmc].mdev = NULL;
+
 				i10nm_printk(KERN_ERR, "This isn't an hbm mc!\n");
 				return -ENODEV;
 			}
@@ -421,6 +429,7 @@
 	X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(ICELAKE_X,		X86_STEPPINGS(0x4, 0xf), &i10nm_cfg1),
 	X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(ICELAKE_D,		X86_STEPPINGS(0x0, 0xf), &i10nm_cfg1),
 	X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(SAPPHIRERAPIDS_X,	X86_STEPPINGS(0x0, 0xf), &spr_cfg),
+	X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(EMERALDRAPIDS_X,	X86_STEPPINGS(0x0, 0xf), &spr_cfg),
 	{}
 };
 MODULE_DEVICE_TABLE(x86cpu, i10nm_cpuids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/ie31200_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/ie31200_edac.c
@@ -83,8 +83,6 @@
 	 (((did) & PCI_DEVICE_ID_INTEL_IE31200_HB_CFL_MASK) ==                 \
 	  PCI_DEVICE_ID_INTEL_IE31200_HB_CFL_MASK))
 
-#define IE31200_DIMMS			4
-#define IE31200_RANKS			8
 #define IE31200_RANKS_PER_CHANNEL	4
 #define IE31200_DIMMS_PER_CHANNEL	2
 #define IE31200_CHANNELS		2
@@ -156,6 +154,7 @@
 #define IE31200_MAD_DIMM_0_OFFSET		0x5004
 #define IE31200_MAD_DIMM_0_OFFSET_SKL		0x500C
 #define IE31200_MAD_DIMM_SIZE			GENMASK_ULL(7, 0)
+#define IE31200_MAD_DIMM_SIZE_SKL		GENMASK_ULL(5, 0)
 #define IE31200_MAD_DIMM_A_RANK			BIT(17)
 #define IE31200_MAD_DIMM_A_RANK_SHIFT		17
 #define IE31200_MAD_DIMM_A_RANK_SKL		BIT(10)
@@ -369,7 +368,7 @@
 static void __skl_populate_dimm_info(struct dimm_data *dd, u32 addr_decode,
 				     int chan)
 {
-	dd->size = (addr_decode >> (chan << 4)) & IE31200_MAD_DIMM_SIZE;
+	dd->size = (addr_decode >> (chan << 4)) & IE31200_MAD_DIMM_SIZE_SKL;
 	dd->dual_rank = (addr_decode & (IE31200_MAD_DIMM_A_RANK_SKL << (chan << 4))) ? 1 : 0;
 	dd->x16_width = ((addr_decode & (IE31200_MAD_DIMM_A_WIDTH_SKL << (chan << 4))) >>
 				(IE31200_MAD_DIMM_A_WIDTH_SKL_SHIFT + (chan << 4)));
@@ -418,7 +417,7 @@
 
 	nr_channels = how_many_channels(pdev);
 	layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
-	layers[0].size = IE31200_DIMMS;
+	layers[0].size = IE31200_RANKS_PER_CHANNEL;
 	layers[0].is_virt_csrow = true;
 	layers[1].type = EDAC_MC_LAYER_CHANNEL;
 	layers[1].size = nr_channels;
@@ -608,7 +607,7 @@
 
 	pci_rc = pci_register_driver(&ie31200_driver);
 	if (pci_rc < 0)
-		goto fail0;
+		return pci_rc;
 
 	if (!mci_pdev) {
 		ie31200_registered = 0;
@@ -619,11 +618,13 @@
 			if (mci_pdev)
 				break;
 		}
+
 		if (!mci_pdev) {
 			edac_dbg(0, "ie31200 pci_get_device fail\n");
 			pci_rc = -ENODEV;
-			goto fail1;
+			goto fail0;
 		}
+
 		pci_rc = ie31200_init_one(mci_pdev, &ie31200_pci_tbl[i]);
 		if (pci_rc < 0) {
 			edac_dbg(0, "ie31200 init fail\n");
@@ -631,12 +632,12 @@
 			goto fail1;
 		}
 	}
-	return 0;
 
+	return 0;
 fail1:
-	pci_unregister_driver(&ie31200_driver);
-fail0:
 	pci_dev_put(mci_pdev);
+fail0:
+	pci_unregister_driver(&ie31200_driver);
 
 	return pci_rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/igen6_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/igen6_edac.c
@@ -27,7 +27,7 @@
 #include "edac_mc.h"
 #include "edac_module.h"
 
-#define IGEN6_REVISION	"v2.5"
+#define IGEN6_REVISION	"v2.5.1"
 
 #define EDAC_MOD_STR	"igen6_edac"
 #define IGEN6_NMI_NAME	"igen6_ibecc"
@@ -245,7 +245,7 @@
 	if (igen6_tom <= _4GB)
 		return eaddr + igen6_tolud - _4GB;
 
-	if (eaddr < _4GB)
+	if (eaddr >= igen6_tom)
 		return eaddr + igen6_tolud - igen6_tom;
 
 	return eaddr;
@@ -627,7 +627,7 @@
 
 	rc = pci_read_config_word(imc->pdev, ERRCMD_OFFSET, &errcmd);
 	if (rc)
-		return rc;
+		return pcibios_err_to_errno(rc);
 
 	if (enable)
 		errcmd |= ERRCMD_CE | ERRSTS_UE;
@@ -636,7 +636,7 @@
 
 	rc = pci_write_config_word(imc->pdev, ERRCMD_OFFSET, errcmd);
 	if (rc)
-		return rc;
+		return pcibios_err_to_errno(rc);
 
 	return 0;
 }
@@ -1075,6 +1075,7 @@
 	imc->mci = mci;
 	return 0;
 fail3:
+	mci->pvt_info = NULL;
 	kfree(mci->ctl_name);
 fail2:
 	edac_mc_free(mci);
@@ -1099,6 +1100,7 @@
 
 		edac_mc_del_mc(mci->pdev);
 		kfree(mci->ctl_name);
+		mci->pvt_info = NULL;
 		edac_mc_free(mci);
 		iounmap(imc->window);
 	}
@@ -1216,9 +1218,6 @@
 	INIT_WORK(&ecclog_work, ecclog_work_cb);
 	init_irq_work(&ecclog_irq_work, ecclog_irq_work_cb);
 
-	/* Check if any pending errors before registering the NMI handler */
-	ecclog_handler();
-
 	rc = register_err_handler();
 	if (rc)
 		goto fail3;
@@ -1230,6 +1229,9 @@
 		goto fail4;
 	}
 
+	/* Check if any pending errors before/during the registration of the error handler */
+	ecclog_handler();
+
 	igen6_debug_setup();
 	return 0;
 fail4:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/pl310_edac_l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/pl310_edac_l2.c
@@ -0,0 +1,233 @@
+/*
+ * Pl310 L2 Cache EDAC Driver
+ *
+ * Copyright (C) 2013-2014 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#include <linux/edac.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <asm/hardware/cache-l2x0.h>
+#include "edac_module.h"
+
+/* Auxilary control register definitions */
+#define L2X0_AUX_CTRL_PARITY_MASK	BIT(21)
+
+/* Interrupt imask/status/clear register definitions */
+#define L2X0_INTR_PARRD_MASK	0x4
+#define L2X0_INTR_PARRT_MASK	0x2
+
+/**
+ * struct pl310_edac_l2_priv - Zynq L2 cache controller private instance data
+ * @base:		Base address of the controller
+ * @irq:		Interrupt number
+ */
+struct pl310_edac_l2_priv {
+	void __iomem *base;
+	int irq;
+};
+
+/**
+ * pl310_edac_l2_parityerr_check - Check controller staus for parity errors
+ * @dci:	Pointer to the edac device controller instance
+ *
+ * This routine is used to check and post parity errors
+ */
+static void pl310_edac_l2_parityerr_check(struct edac_device_ctl_info *dci)
+{
+	struct pl310_edac_l2_priv *priv = dci->pvt_info;
+	u32 regval;
+
+	regval = readl(priv->base + L2X0_RAW_INTR_STAT);
+	if (regval & L2X0_INTR_PARRD_MASK) {
+		/* Data parity error will be reported as correctable error */
+		writel(L2X0_INTR_PARRD_MASK, priv->base + L2X0_INTR_CLEAR);
+		edac_device_handle_ce(dci, 0, 0, dci->ctl_name);
+	}
+	if (regval & L2X0_INTR_PARRT_MASK) {
+		/* tag parity error will be reported as uncorrectable error */
+		writel(L2X0_INTR_PARRT_MASK, priv->base + L2X0_INTR_CLEAR);
+		edac_device_handle_ue(dci, 0, 0, dci->ctl_name);
+	}
+}
+
+/**
+ * pl310_edac_l2_int_handler - ISR fucntion for l2cahe controller
+ * @irq:	Irq Number
+ * @device:	Pointer to the edac device controller instance
+ *
+ * This routine is triggered whenever there is parity error detected
+ *
+ * Return: Always returns IRQ_HANDLED
+ */
+static irqreturn_t pl310_edac_l2_int_handler(int irq, void *device)
+{
+	pl310_edac_l2_parityerr_check((struct edac_device_ctl_info *)device);
+	return IRQ_HANDLED;
+}
+
+/**
+ * pl310_edac_l2_poll_handler - Poll the status reg for parity errors
+ * @dci:	Pointer to the edac device controller instance
+ *
+ * This routine is used to check and post parity errors and is called by
+ * the EDAC polling thread
+ */
+static void pl310_edac_l2_poll_handler(struct edac_device_ctl_info *dci)
+{
+	pl310_edac_l2_parityerr_check(dci);
+}
+
+/**
+ * pl310_edac_l2_get_paritystate - check the parity enable/disable status
+ * @base:	Pointer to the contoller base address
+ *
+ * This routine returns the parity enable/diable status for the controller
+ *
+ * Return: true/false -  parity enabled/disabled.
+ */
+static bool pl310_edac_l2_get_paritystate(void __iomem *base)
+{
+	u32 regval;
+
+	regval = readl(base + L2X0_AUX_CTRL);
+	if (regval & L2X0_AUX_CTRL_PARITY_MASK)
+		return true;
+
+	return false;
+}
+
+/**
+ * pl310_edac_l2_probe - Check controller and bind driver
+ * @pdev:	Pointer to the platform_device struct
+ *
+ * This routine probes a specific arm,pl310-cache instance for binding
+ * with the driver.
+ *
+ * Return: 0 if the controller instance was successfully bound to the
+ * driver; otherwise, < 0 on error.
+ */
+static int pl310_edac_l2_probe(struct platform_device *pdev)
+{
+	struct edac_device_ctl_info *dci;
+	struct pl310_edac_l2_priv *priv;
+	int rc;
+	struct resource *res;
+	void __iomem *baseaddr;
+	u32 regval;
+
+	/* Get the data from the platform device */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	baseaddr = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(baseaddr))
+		return PTR_ERR(baseaddr);
+
+	/* Check for the ecc enable status */
+	if (pl310_edac_l2_get_paritystate(baseaddr) == false) {
+		dev_err(&pdev->dev, "parity check not enabled\n");
+		return -ENXIO;
+	}
+
+	dci = edac_device_alloc_ctl_info(sizeof(*priv), "l2cache",
+					 1, "L", 1, 1, NULL, 0,
+					 edac_device_alloc_index());
+	if (IS_ERR(dci))
+		return PTR_ERR(dci);
+
+	priv = dci->pvt_info;
+	priv->base = baseaddr;
+	dci->dev = &pdev->dev;
+	dci->mod_name = "pl310_edac_l2";
+	dci->ctl_name = "pl310_l2_controller";
+	dci->dev_name = dev_name(&pdev->dev);
+
+	priv->irq = platform_get_irq(pdev, 0);
+	rc = devm_request_irq(&pdev->dev, priv->irq,
+				pl310_edac_l2_int_handler,
+				0, dev_name(&pdev->dev), (void *)dci);
+	if (rc < 0) {
+		dci->edac_check = pl310_edac_l2_poll_handler;
+		edac_op_state = EDAC_OPSTATE_POLL;
+	}
+
+	rc = edac_device_add_device(dci);
+	if (rc) {
+		dev_err(&pdev->dev, "failed to register with EDAC core\n");
+		goto del_edac_device;
+	}
+
+	if (edac_op_state != EDAC_OPSTATE_POLL) {
+		regval = readl(priv->base+L2X0_INTR_MASK);
+		regval |= (L2X0_INTR_PARRD_MASK | L2X0_INTR_PARRT_MASK);
+		writel(regval, priv->base+L2X0_INTR_MASK);
+	}
+
+	return rc;
+
+del_edac_device:
+	edac_device_del_device(&pdev->dev);
+	edac_device_free_ctl_info(dci);
+
+	return rc;
+}
+
+/**
+ * pl310_edac_l2_remove - Unbind driver from controller
+ * @pdev:	Pointer to the platform_device struct
+ *
+ * This routine unbinds the EDAC device controller instance associated
+ * with the specified arm,pl310-cache controller described by the
+ * OpenFirmware device tree node passed as a parameter.
+ *
+ * Return: Always returns 0
+ */
+static int pl310_edac_l2_remove(struct platform_device *pdev)
+{
+	struct edac_device_ctl_info *dci = platform_get_drvdata(pdev);
+	struct pl310_edac_l2_priv *priv = dci->pvt_info;
+	u32 regval;
+
+	if (edac_op_state != EDAC_OPSTATE_POLL) {
+		regval = readl(priv->base+L2X0_INTR_MASK);
+		regval &= ~(L2X0_INTR_PARRD_MASK | L2X0_INTR_PARRT_MASK);
+		writel(regval, priv->base+L2X0_INTR_MASK);
+	}
+
+	edac_device_del_device(&pdev->dev);
+	edac_device_free_ctl_info(dci);
+
+	return 0;
+}
+
+/* Device tree node type and compatible tuples this driver can match on */
+static const struct of_device_id pl310_edac_l2_match[] = {
+	{ .compatible = "arm,pl310-cache", },
+	{ /* end of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, pl310_edac_l2_match);
+
+static struct platform_driver pl310_edac_l2_driver = {
+	.driver = {
+		 .name = "pl310-edac-l2",
+		 .of_match_table = pl310_edac_l2_match,
+	},
+	.probe = pl310_edac_l2_probe,
+	.remove = pl310_edac_l2_remove,
+};
+
+module_platform_driver(pl310_edac_l2_driver);
+
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("pl310 L2 EDAC driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/qcom_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/qcom_edac.c
@@ -252,7 +252,7 @@
 static int
 dump_syn_reg(struct edac_device_ctl_info *edev_ctl, int err_type, u32 bank)
 {
-	struct llcc_drv_data *drv = edev_ctl->pvt_info;
+	struct llcc_drv_data *drv = edev_ctl->dev->platform_data;
 	int ret;
 
 	ret = dump_syn_reg_values(drv, bank, err_type);
@@ -289,7 +289,7 @@
 llcc_ecc_irq_handler(int irq, void *edev_ctl)
 {
 	struct edac_device_ctl_info *edac_dev_ctl = edev_ctl;
-	struct llcc_drv_data *drv = edac_dev_ctl->pvt_info;
+	struct llcc_drv_data *drv = edac_dev_ctl->dev->platform_data;
 	irqreturn_t irq_rc = IRQ_NONE;
 	u32 drp_error, trp_error, i;
 	int ret;
@@ -358,7 +358,6 @@
 	edev_ctl->dev_name = dev_name(dev);
 	edev_ctl->ctl_name = "llcc";
 	edev_ctl->panic_on_ue = LLCC_ERP_PANIC_ON_UE;
-	edev_ctl->pvt_info = llcc_driv_data;
 
 	rc = edac_device_add_device(edev_ctl);
 	if (rc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/sb_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/sb_edac.c
@@ -1052,7 +1052,7 @@
 	pci_read_config_dword(pvt->info.pci_vtd, HASWELL_TOHM_1, &reg);
 	rc = ((reg << 6) | rc) << 26;
 
-	return rc | 0x1ffffff;
+	return rc | 0x3ffffff;
 }
 
 static u64 knl_get_tolm(struct sbridge_pvt *pvt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/skx_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/skx_base.c
@@ -510,7 +510,7 @@
 }
 
 static u8 skx_close_row[] = {
-	15, 16, 17, 18, 20, 21, 22, 28, 10, 11, 12, 13, 29, 30, 31, 32, 33
+	15, 16, 17, 18, 20, 21, 22, 28, 10, 11, 12, 13, 29, 30, 31, 32, 33, 34
 };
 
 static u8 skx_close_column[] = {
@@ -518,7 +518,7 @@
 };
 
 static u8 skx_open_row[] = {
-	14, 15, 16, 20, 28, 21, 22, 23, 24, 25, 26, 27, 29, 30, 31, 32, 33
+	14, 15, 16, 20, 28, 21, 22, 23, 24, 25, 26, 27, 29, 30, 31, 32, 33, 34
 };
 
 static u8 skx_open_column[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/skx_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/skx_common.c
@@ -46,7 +46,7 @@
 static LIST_HEAD(dev_edac_list);
 static bool skx_mem_cfg_2lm;
 
-int __init skx_adxl_get(void)
+int skx_adxl_get(void)
 {
 	const char * const *names;
 	int i, j;
@@ -108,12 +108,14 @@
 
 	return -ENODEV;
 }
+EXPORT_SYMBOL_GPL(skx_adxl_get);
 
-void __exit skx_adxl_put(void)
+void skx_adxl_put(void)
 {
 	kfree(adxl_values);
 	kfree(adxl_msg);
 }
+EXPORT_SYMBOL_GPL(skx_adxl_put);
 
 static bool skx_adxl_decode(struct decoded_addr *res, bool error_in_1st_level_mem)
 {
@@ -180,12 +182,14 @@
 {
 	skx_mem_cfg_2lm = mem_cfg_2lm;
 }
+EXPORT_SYMBOL_GPL(skx_set_mem_cfg);
 
 void skx_set_decode(skx_decode_f decode, skx_show_retry_log_f show_retry_log)
 {
 	skx_decode = decode;
 	skx_show_retry_rd_err_log = show_retry_log;
 }
+EXPORT_SYMBOL_GPL(skx_set_decode);
 
 int skx_get_src_id(struct skx_dev *d, int off, u8 *id)
 {
@@ -199,6 +203,7 @@
 	*id = GET_BITFIELD(reg, 12, 14);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(skx_get_src_id);
 
 int skx_get_node_id(struct skx_dev *d, u8 *id)
 {
@@ -212,6 +217,7 @@
 	*id = GET_BITFIELD(reg, 0, 2);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(skx_get_node_id);
 
 static int get_width(u32 mtr)
 {
@@ -277,6 +283,7 @@
 		*list = &dev_edac_list;
 	return ndev;
 }
+EXPORT_SYMBOL_GPL(skx_get_all_bus_mappings);
 
 int skx_get_hi_lo(unsigned int did, int off[], u64 *tolm, u64 *tohm)
 {
@@ -316,6 +323,7 @@
 	pci_dev_put(pdev);
 	return -ENODEV;
 }
+EXPORT_SYMBOL_GPL(skx_get_hi_lo);
 
 static int skx_get_dimm_attr(u32 reg, int lobit, int hibit, int add,
 			     int minval, int maxval, const char *name)
@@ -387,6 +395,7 @@
 
 	return 1;
 }
+EXPORT_SYMBOL_GPL(skx_get_dimm_info);
 
 int skx_get_nvdimm_info(struct dimm_info *dimm, struct skx_imc *imc,
 			int chan, int dimmno, const char *mod_str)
@@ -435,6 +444,7 @@
 
 	return (size == 0 || size == ~0ull) ? 0 : 1;
 }
+EXPORT_SYMBOL_GPL(skx_get_nvdimm_info);
 
 int skx_register_mci(struct skx_imc *imc, struct pci_dev *pdev,
 		     const char *ctl_name, const char *mod_str,
@@ -505,6 +515,7 @@
 	imc->mci = NULL;
 	return rc;
 }
+EXPORT_SYMBOL_GPL(skx_register_mci);
 
 static void skx_unregister_mci(struct skx_imc *imc)
 {
@@ -686,6 +697,7 @@
 	mce->kflags |= MCE_HANDLED_EDAC;
 	return NOTIFY_DONE;
 }
+EXPORT_SYMBOL_GPL(skx_mce_check_error);
 
 void skx_remove(void)
 {
@@ -723,3 +735,8 @@
 		kfree(d);
 	}
 }
+EXPORT_SYMBOL_GPL(skx_remove);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Tony Luck");
+MODULE_DESCRIPTION("MC Driver for Intel server processors");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/skx_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/skx_common.h
@@ -162,8 +162,8 @@
 typedef bool (*skx_decode_f)(struct decoded_addr *res);
 typedef void (*skx_show_retry_log_f)(struct decoded_addr *res, char *msg, int len, bool scrub_err);
 
-int __init skx_adxl_get(void);
-void __exit skx_adxl_put(void);
+int skx_adxl_get(void);
+void skx_adxl_put(void);
 void skx_set_decode(skx_decode_f decode, skx_show_retry_log_f show_retry_log);
 void skx_set_mem_cfg(bool mem_cfg_2lm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/synopsys_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/synopsys_edac.c
@@ -22,6 +22,8 @@
 #include <linux/edac.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/sizes.h>
 #include <linux/interrupt.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
@@ -101,6 +103,7 @@
 /* DDR ECC Quirks */
 #define DDR_ECC_INTR_SUPPORT		BIT(0)
 #define DDR_ECC_DATA_POISON_SUPPORT	BIT(1)
+#define DDR_ECC_INTR_SELF_CLEAR		BIT(2)
 
 /* ZynqMP Enhanced DDR memory controller registers that are relevant to ECC */
 /* ECC Configuration Registers */
@@ -163,6 +166,11 @@
 #define ECC_STAT_CECNT_SHIFT		8
 #define ECC_STAT_BITNUM_MASK		0x7F
 
+/* ECC error count register definitions */
+#define ECC_ERRCNT_UECNT_MASK		0xFFFF0000
+#define ECC_ERRCNT_UECNT_SHIFT		16
+#define ECC_ERRCNT_CECNT_MASK		0xFFFF
+
 /* DDR QOS Interrupt register definitions */
 #define DDR_QOS_IRQ_STAT_OFST		0x20200
 #define DDR_QOSUE_MASK			0x4
@@ -171,6 +179,10 @@
 #define DDR_QOS_IRQ_EN_OFST		0x20208
 #define DDR_QOS_IRQ_DB_OFST		0x2020C
 
+/* DDR QOS Interrupt register definitions */
+#define DDR_UE_MASK			BIT(9)
+#define DDR_CE_MASK			BIT(8)
+
 /* ECC Corrected Error Register Mask and Shifts*/
 #define ECC_CEADDR0_RW_MASK		0x3FFFF
 #define ECC_CEADDR0_RNK_MASK		BIT(24)
@@ -303,6 +315,7 @@
 /**
  * struct synps_edac_priv - DDR memory controller private instance data.
  * @baseaddr:		Base address of the DDR controller.
+ * @reglock:		Concurrent CSRs access lock.
  * @message:		Buffer for framing the event specific info.
  * @stat:		ECC status information.
  * @p_data:		Platform data.
@@ -317,6 +330,7 @@
  */
 struct synps_edac_priv {
 	void __iomem *baseaddr;
+	spinlock_t reglock;
 	char message[SYNPS_EDAC_MSG_SIZE];
 	struct synps_ecc_status stat;
 	const struct synps_platform_data *p_data;
@@ -338,6 +352,7 @@
  * @get_mtype:		Get mtype.
  * @get_dtype:		Get dtype.
  * @get_ecc_state:	Get ECC state.
+ * @get_mem_info:	Get EDAC memory info
  * @quirks:		To differentiate IPs.
  */
 struct synps_platform_data {
@@ -345,6 +360,9 @@
 	enum mem_type (*get_mtype)(const void __iomem *base);
 	enum dev_type (*get_dtype)(const void __iomem *base);
 	bool (*get_ecc_state)(void __iomem *base);
+#ifdef CONFIG_EDAC_DEBUG
+	u64 (*get_mem_info)(struct synps_edac_priv *priv);
+#endif
 	int quirks;
 };
 
@@ -403,6 +421,25 @@
 	return 0;
 }
 
+#ifdef CONFIG_EDAC_DEBUG
+/**
+ * zynqmp_get_mem_info - Get the current memory info.
+ * @priv:	DDR memory controller private instance data.
+ *
+ * Return: host interface address.
+ */
+static u64 zynqmp_get_mem_info(struct synps_edac_priv *priv)
+{
+	u64 hif_addr = 0, linear_addr;
+
+	linear_addr = priv->poison_addr;
+	if (linear_addr >= SZ_32G)
+		linear_addr = linear_addr - SZ_32G + SZ_2G;
+	hif_addr = linear_addr >> 3;
+	return hif_addr;
+}
+#endif
+
 /**
  * zynqmp_get_error_info - Get the current ECC error info.
  * @priv:	DDR memory controller private instance data.
@@ -412,21 +449,23 @@
 static int zynqmp_get_error_info(struct synps_edac_priv *priv)
 {
 	struct synps_ecc_status *p;
-	u32 regval, clearval = 0;
+	u32 regval, clearval;
+	unsigned long flags;
 	void __iomem *base;
 
 	base = priv->baseaddr;
 	p = &priv->stat;
 
+	regval = readl(base + ECC_ERRCNT_OFST);
+	p->ce_cnt = regval & ECC_ERRCNT_CECNT_MASK;
+	p->ue_cnt = (regval & ECC_ERRCNT_UECNT_MASK) >> ECC_ERRCNT_UECNT_SHIFT;
+	if (!p->ce_cnt)
+		goto ue_err;
+
 	regval = readl(base + ECC_STAT_OFST);
 	if (!regval)
 		return 1;
 
-	p->ce_cnt = (regval & ECC_STAT_CECNT_MASK) >> ECC_STAT_CECNT_SHIFT;
-	p->ue_cnt = (regval & ECC_STAT_UECNT_MASK) >> ECC_STAT_UECNT_SHIFT;
-	if (!p->ce_cnt)
-		goto ue_err;
-
 	p->ceinfo.bitpos = (regval & ECC_STAT_BITNUM_MASK);
 
 	regval = readl(base + ECC_CEADDR0_OFST);
@@ -455,10 +494,14 @@
 	p->ueinfo.blknr = (regval & ECC_CEADDR1_BLKNR_MASK);
 	p->ueinfo.data = readl(base + ECC_UESYND0_OFST);
 out:
-	clearval = ECC_CTRL_CLR_CE_ERR | ECC_CTRL_CLR_CE_ERRCNT;
-	clearval |= ECC_CTRL_CLR_UE_ERR | ECC_CTRL_CLR_UE_ERRCNT;
+	spin_lock_irqsave(&priv->reglock, flags);
+
+	clearval = readl(base + ECC_CLR_OFST) |
+		   ECC_CTRL_CLR_CE_ERR | ECC_CTRL_CLR_CE_ERRCNT |
+		   ECC_CTRL_CLR_UE_ERR | ECC_CTRL_CLR_UE_ERRCNT;
 	writel(clearval, base + ECC_CLR_OFST);
-	writel(0x0, base + ECC_CLR_OFST);
+
+	spin_unlock_irqrestore(&priv->reglock, flags);
 
 	return 0;
 }
@@ -491,7 +534,7 @@
 		}
 
 		edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci,
-				     p->ce_cnt, 0, 0, 0, 0, 0, -1,
+				     priv->ce_cnt, 0, 0, 0, 0, 0, -1,
 				     priv->message, "");
 	}
 
@@ -509,13 +552,52 @@
 		}
 
 		edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci,
-				     p->ue_cnt, 0, 0, 0, 0, 0, -1,
+				     priv->ue_cnt, 0, 0, 0, 0, 0, -1,
 				     priv->message, "");
 	}
 
 	memset(p, 0, sizeof(*p));
 }
 
+static void enable_intr(struct synps_edac_priv *priv)
+{
+	unsigned long flags;
+
+	/* Enable UE/CE Interrupts */
+	if (!(priv->p_data->quirks & DDR_ECC_INTR_SELF_CLEAR)) {
+		writel(DDR_QOSUE_MASK | DDR_QOSCE_MASK,
+		       priv->baseaddr + DDR_QOS_IRQ_EN_OFST);
+
+		return;
+	}
+
+	spin_lock_irqsave(&priv->reglock, flags);
+
+	writel(DDR_UE_MASK | DDR_CE_MASK,
+	       priv->baseaddr + ECC_CLR_OFST);
+
+	spin_unlock_irqrestore(&priv->reglock, flags);
+}
+
+static void disable_intr(struct synps_edac_priv *priv)
+{
+	unsigned long flags;
+
+	/* Disable UE/CE Interrupts */
+	if (!(priv->p_data->quirks & DDR_ECC_INTR_SELF_CLEAR)) {
+		writel(DDR_QOSUE_MASK | DDR_QOSCE_MASK,
+		       priv->baseaddr + DDR_QOS_IRQ_DB_OFST);
+
+		return;
+	}
+
+	spin_lock_irqsave(&priv->reglock, flags);
+
+	writel(0, priv->baseaddr + ECC_CLR_OFST);
+
+	spin_unlock_irqrestore(&priv->reglock, flags);
+}
+
 /**
  * intr_handler - Interrupt Handler for ECC interrupts.
  * @irq:        IRQ number.
@@ -533,10 +615,16 @@
 	priv = mci->pvt_info;
 	p_data = priv->p_data;
 
-	regval = readl(priv->baseaddr + DDR_QOS_IRQ_STAT_OFST);
-	regval &= (DDR_QOSCE_MASK | DDR_QOSUE_MASK);
-	if (!(regval & ECC_CE_UE_INTR_MASK))
-		return IRQ_NONE;
+	/*
+	 * v3.0 of the controller has the ce/ue bits cleared automatically,
+	 * so this condition does not apply.
+	 */
+	if (!(priv->p_data->quirks & DDR_ECC_INTR_SELF_CLEAR)) {
+		regval = readl(priv->baseaddr + DDR_QOS_IRQ_STAT_OFST);
+		regval &= (DDR_QOSCE_MASK | DDR_QOSUE_MASK);
+		if (!(regval & ECC_CE_UE_INTR_MASK))
+			return IRQ_NONE;
+	}
 
 	status = p_data->get_error_info(priv);
 	if (status)
@@ -548,7 +636,10 @@
 
 	edac_dbg(3, "Total error count CE %d UE %d\n",
 		 priv->ce_cnt, priv->ue_cnt);
-	writel(regval, priv->baseaddr + DDR_QOS_IRQ_STAT_OFST);
+	/* v3.0 of the controller does not have this register */
+	if (!(priv->p_data->quirks & DDR_ECC_INTR_SELF_CLEAR))
+		writel(regval, priv->baseaddr + DDR_QOS_IRQ_STAT_OFST);
+
 	return IRQ_HANDLED;
 }
 
@@ -831,20 +922,6 @@
 	init_csrows(mci);
 }
 
-static void enable_intr(struct synps_edac_priv *priv)
-{
-	/* Enable UE/CE Interrupts */
-	writel(DDR_QOSUE_MASK | DDR_QOSCE_MASK,
-			priv->baseaddr + DDR_QOS_IRQ_EN_OFST);
-}
-
-static void disable_intr(struct synps_edac_priv *priv)
-{
-	/* Disable UE/CE Interrupts */
-	writel(DDR_QOSUE_MASK | DDR_QOSCE_MASK,
-			priv->baseaddr + DDR_QOS_IRQ_DB_OFST);
-}
-
 static int setup_irq(struct mem_ctl_info *mci,
 		     struct platform_device *pdev)
 {
@@ -883,6 +960,9 @@
 	.get_mtype	= zynqmp_get_mtype,
 	.get_dtype	= zynqmp_get_dtype,
 	.get_ecc_state	= zynqmp_get_ecc_state,
+#ifdef CONFIG_EDAC_DEBUG
+	.get_mem_info	= zynqmp_get_mem_info,
+#endif
 	.quirks         = (DDR_ECC_INTR_SUPPORT
 #ifdef CONFIG_EDAC_DEBUG
 			  | DDR_ECC_DATA_POISON_SUPPORT
@@ -890,6 +970,19 @@
 			  ),
 };
 
+static const struct synps_platform_data synopsys_edac_def = {
+	.get_error_info	= zynqmp_get_error_info,
+	.get_mtype	= zynqmp_get_mtype,
+	.get_dtype	= zynqmp_get_dtype,
+	.get_ecc_state	= zynqmp_get_ecc_state,
+	.quirks         = (DDR_ECC_INTR_SUPPORT | DDR_ECC_INTR_SELF_CLEAR
+#ifdef CONFIG_EDAC_DEBUG
+			  | DDR_ECC_DATA_POISON_SUPPORT
+#endif
+			  ),
+};
+
+
 static const struct of_device_id synps_edac_match[] = {
 	{
 		.compatible = "xlnx,zynq-ddrc-a05",
@@ -900,6 +993,10 @@
 		.data = (void *)&zynqmp_edac_def
 	},
 	{
+		.compatible = "snps,ddrc-3.80a",
+		.data = (void *)&synopsys_edac_def
+	},
+	{
 		/* end of table */
 	}
 };
@@ -919,10 +1016,16 @@
 static void ddr_poison_setup(struct synps_edac_priv *priv)
 {
 	int col = 0, row = 0, bank = 0, bankgrp = 0, rank = 0, regval;
+	const struct synps_platform_data *p_data;
 	int index;
 	ulong hif_addr = 0;
 
-	hif_addr = priv->poison_addr >> 3;
+	p_data = priv->p_data;
+
+	if (p_data->get_mem_info)
+		hif_addr = p_data->get_mem_info(priv);
+	else
+		hif_addr = priv->poison_addr >> 3;
 
 	for (index = 0; index < DDR_MAX_ROW_SHIFT; index++) {
 		if (priv->row_shift[index])
@@ -1326,6 +1429,7 @@
 	priv = mci->pvt_info;
 	priv->baseaddr = baseaddr;
 	priv->p_data = p_data;
+	spin_lock_init(&priv->reglock);
 
 	mc_init(mci, pdev);
 
@@ -1352,8 +1456,7 @@
 		}
 	}
 
-	if (of_device_is_compatible(pdev->dev.of_node,
-				    "xlnx,zynqmp-ddrc-2.40a"))
+	if (priv->p_data->quirks & DDR_ECC_INTR_SUPPORT)
 		setup_address_map(priv);
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/thunderx_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/thunderx_edac.c
@@ -1133,7 +1133,7 @@
 		decode_register(other, OCX_OTHER_SIZE,
 				ocx_com_errors, ctx->reg_com_int);
 
-		strncat(msg, other, OCX_MESSAGE_SIZE);
+		strlcat(msg, other, OCX_MESSAGE_SIZE);
 
 		for (lane = 0; lane < OCX_RX_LANES; lane++)
 			if (ctx->reg_com_int & BIT(lane)) {
@@ -1142,12 +1142,12 @@
 					 lane, ctx->reg_lane_int[lane],
 					 lane, ctx->reg_lane_stat11[lane]);
 
-				strncat(msg, other, OCX_MESSAGE_SIZE);
+				strlcat(msg, other, OCX_MESSAGE_SIZE);
 
 				decode_register(other, OCX_OTHER_SIZE,
 						ocx_lane_errors,
 						ctx->reg_lane_int[lane]);
-				strncat(msg, other, OCX_MESSAGE_SIZE);
+				strlcat(msg, other, OCX_MESSAGE_SIZE);
 			}
 
 		if (ctx->reg_com_int & OCX_COM_INT_CE)
@@ -1217,7 +1217,7 @@
 		decode_register(other, OCX_OTHER_SIZE,
 				ocx_com_link_errors, ctx->reg_com_link_int);
 
-		strncat(msg, other, OCX_MESSAGE_SIZE);
+		strlcat(msg, other, OCX_MESSAGE_SIZE);
 
 		if (ctx->reg_com_link_int & OCX_COM_LINK_INT_UE)
 			edac_device_handle_ue(ocx->edac_dev, 0, 0, msg);
@@ -1896,7 +1896,7 @@
 
 		decode_register(other, L2C_OTHER_SIZE, l2_errors, ctx->reg_int);
 
-		strncat(msg, other, L2C_MESSAGE_SIZE);
+		strlcat(msg, other, L2C_MESSAGE_SIZE);
 
 		if (ctx->reg_int & mask_ue)
 			edac_device_handle_ue(l2c->edac_dev, 0, 0, msg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/xgene_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/xgene_edac.c
@@ -1919,7 +1919,7 @@
 			irq = platform_get_irq_optional(pdev, i);
 			if (irq < 0) {
 				dev_err(&pdev->dev, "No IRQ resource\n");
-				rc = -EINVAL;
+				rc = irq;
 				goto out_err;
 			}
 			rc = devm_request_irq(&pdev->dev, irq,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/xilinx_ddrmc_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/xilinx_ddrmc_edac.c
@@ -0,0 +1,1279 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/edac.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/sizes.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/firmware/xlnx-error-events.h>
+#include <linux/firmware/xlnx-event-manager.h>
+
+#include "edac_module.h"
+
+static bool disable_event; /* No support for notification. Default: 0 (Off) */
+module_param(disable_event, bool, 0444);
+MODULE_PARM_DESC(disable_event, "No error notification support. Default: 0 (Off)");
+
+/* Granularity of reported error in bytes */
+#define XDDR_EDAC_ERR_GRAIN			1
+
+#define XDDR_EDAC_MSG_SIZE			256
+
+#define XDDR_PCSR_OFFSET			0xC
+#define XDDR_ISR_OFFSET				0x14
+#define XDDR_IRQ_EN_OFFSET			0x20
+#define XDDR_IRQ1_EN_OFFSET			0x2C
+#define XDDR_IRQ_DIS_OFFSET			0x24
+#define XDDR_IRQ_CE_MASK			GENMASK(18, 15)
+#define XDDR_IRQ_UE_MASK			GENMASK(14, 11)
+
+#define XDDR_REG_CONFIG0_OFFSET			0x258
+#define XDDR_REG_CONFIG0_BUS_WIDTH_MASK		GENMASK(19, 18)
+#define XDDR_REG_CONFIG0_BUS_WIDTH_SHIFT	18
+#define XDDR_REG_CONFIG0_NUM_CHANS_MASK		BIT(17)
+#define XDDR_REG_CONFIG0_NUM_CHANS_SHIFT	17
+#define XDDR_REG_CONFIG0_NUM_RANKS_MASK		GENMASK(15, 14)
+#define XDDR_REG_CONFIG0_NUM_RANKS_SHIFT	14
+#define XDDR_REG_CONFIG0_SIZE_MASK		GENMASK(10, 8)
+#define XDDR_REG_CONFIG0_SIZE_SHIFT		8
+
+#define XDDR_REG_PINOUT_OFFSET			0x25C
+#define XDDR_REG_PINOUT_ECC_EN_MASK		GENMASK(7, 5)
+
+#define ECCW0_FLIP_CTRL				0x109C
+#define ECCW0_FLIP0_OFFSET			0x10A0
+#define ECCW1_FLIP_CTRL				0x10AC
+#define ECCW1_FLIP0_OFFSET			0x10B0
+#define ECCR0_CERR_STAT_OFFSET			0x10BC
+#define ECCR0_CE_ADDR_LO_OFFSET			0x10C0
+#define ECCR0_CE_ADDR_LO_OFFSET			0x10C0
+#define ECCR0_CE_ADDR_HI_OFFSET			0x10C4
+#define ECCR0_CE_DATA_LO_OFFSET			0x10C8
+#define ECCR0_CE_DATA_HI_OFFSET			0x10CC
+#define ECCR0_CE_DATA_PAR_OFFSET		0x10D0
+
+#define ECCR0_UERR_STAT_OFFSET			0x10D4
+#define ECCR0_UE_ADDR_LO_OFFSET			0x10D8
+#define ECCR0_UE_ADDR_HI_OFFSET			0x10DC
+#define ECCR0_UE_DATA_LO_OFFSET			0x10E0
+#define ECCR0_UE_DATA_HI_OFFSET			0x10E4
+#define ECCR0_UE_DATA_PAR_OFFSET		0x10E8
+
+#define ECCR1_CERR_STAT_OFFSET			0x10F4
+#define ECCR1_CE_ADDR_LO_OFFSET			0x10F8
+#define ECCR1_CE_ADDR_HI_OFFSET			0x10FC
+#define ECCR1_CE_DATA_LO_OFFSET			0x1100
+#define ECCR1_CE_DATA_HI_OFFSET			0x110C
+#define ECCR1_CE_DATA_PAR_OFFSET		0x1108
+
+#define ECCR1_UERR_STAT_OFFSET			0x110C
+#define ECCR1_UE_ADDR_LO_OFFSET			0x1110
+#define ECCR1_UE_ADDR_HI_OFFSET			0x1114
+#define ECCR1_UE_DATA_LO_OFFSET			0x1118
+#define ECCR1_UE_DATA_HI_OFFSET			0x111C
+#define ECCR1_UE_DATA_PAR_OFFSET		0x1120
+
+#define XDDR_NOC_REG_ADEC4_OFFSET		0x44
+#define RANK_0_MASK				GENMASK(5, 0)
+#define RANK_1_MASK				GENMASK(11, 6)
+#define RANK_1_SHIFT				6
+#define LRANK_0_MASK				GENMASK(17, 12)
+#define LRANK_0_SHIFT				12
+#define LRANK_1_MASK				GENMASK(23, 18)
+#define LRANK_1_SHIFT				18
+#define LRANK_2_MASK				GENMASK(29, 24)
+#define LRANK_2_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC5_OFFSET		0x48
+#define ROW_0_MASK				GENMASK(5, 0)
+#define ROW_1_MASK				GENMASK(11, 6)
+#define ROW_1_SHIFT				6
+#define ROW_2_MASK				GENMASK(17, 12)
+#define ROW_2_SHIFT				12
+#define ROW_3_MASK				GENMASK(23, 18)
+#define ROW_3_SHIFT				18
+#define ROW_4_MASK				GENMASK(29, 24)
+#define ROW_4_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC6_OFFSET		0x4C
+#define ROW_5_MASK				GENMASK(5, 0)
+#define ROW_6_MASK				GENMASK(11, 6)
+#define ROW_6_SHIFT				6
+#define ROW_7_MASK				GENMASK(17, 12)
+#define ROW_7_SHIFT				12
+#define ROW_8_MASK				GENMASK(23, 18)
+#define ROW_8_SHIFT				18
+#define ROW_9_MASK				GENMASK(29, 24)
+#define ROW_9_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC7_OFFSET		0x50
+#define ROW_10_MASK				GENMASK(5, 0)
+#define ROW_11_MASK				GENMASK(11, 6)
+#define ROW_11_SHIFT				6
+#define ROW_12_MASK				GENMASK(17, 12)
+#define ROW_12_SHIFT				12
+#define ROW_13_MASK				GENMASK(23, 18)
+#define ROW_13_SHIFT				18
+#define ROW_14_MASK				GENMASK(29, 24)
+#define ROW_14_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC8_OFFSET		0x54
+#define ROW_15_MASK				GENMASK(5, 0)
+#define ROW_16_MASK				GENMASK(11, 6)
+#define ROW_16_SHIFT				6
+#define ROW_17_MASK				GENMASK(17, 12)
+#define ROW_17_SHIFT				12
+#define ROW_18_MASK				GENMASK(23, 18)
+#define ROW_18_SHIFT				18
+#define COL_0_MASK				GENMASK(29, 24)
+#define COL_0_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC9_OFFSET		0x58
+#define COL_1_MASK				GENMASK(5, 0)
+#define COL_2_MASK				GENMASK(11, 6)
+#define COL_2_SHIFT				6
+#define COL_3_MASK				GENMASK(17, 12)
+#define COL_3_SHIFT				12
+#define COL_4_MASK				GENMASK(23, 18)
+#define COL_4_SHIFT				18
+#define COL_5_MASK				GENMASK(29, 24)
+#define COL_5_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC10_OFFSET		0x5C
+#define COL_6_MASK				GENMASK(5, 0)
+#define COL_7_MASK				GENMASK(11, 6)
+#define COL_7_SHIFT				6
+#define COL_8_MASK				GENMASK(17, 12)
+#define COL_8_SHIFT				12
+#define COL_9_MASK				GENMASK(23, 18)
+#define COL_9_SHIFT				18
+#define BANK_0_MASK				GENMASK(29, 24)
+#define BANK_0_SHIFT				24
+
+#define XDDR_NOC_REG_ADEC11_OFFSET		0x60
+#define BANK_1_MASK				GENMASK(5, 0)
+#define GRP_0_MASK				GENMASK(11, 6)
+#define GRP_0_SHIFT				6
+#define GRP_1_MASK				GENMASK(17, 12)
+#define GRP_1_SHIFT				12
+#define CH_0_MASK				GENMASK(23, 18)
+#define CH_0_SHIFT				18
+
+#define XDDR_NOC_REG_ADEC12_OFFSET		0x71C
+#define XDDR_NOC_REG_ADEC13_OFFSET		0x720
+
+#define XDDR_NOC_REG_ADEC14_OFFSET		0x724
+#define XDDR_NOC_ROW_MATCH_MASK			GENMASK(17, 0)
+#define XDDR_NOC_COL_MATCH_MASK			GENMASK(27, 18)
+#define XDDR_NOC_COL_MATCH_SHIFT		18
+#define XDDR_NOC_BANK_MATCH_MASK		GENMASK(29, 28)
+#define XDDR_NOC_BANK_MATCH_SHIFT		28
+#define XDDR_NOC_GRP_MATCH_MASK			GENMASK(31, 30)
+#define XDDR_NOC_GRP_MATCH_SHIFT		30
+
+#define XDDR_NOC_REG_ADEC15_OFFSET		0x728
+#define XDDR_NOC_RANK_MATCH_MASK		GENMASK(1, 0)
+#define XDDR_NOC_LRANK_MATCH_MASK		GENMASK(4, 2)
+#define XDDR_NOC_LRANK_MATCH_SHIFT		2
+#define XDDR_NOC_CH_MATCH_MASK			BIT(5)
+#define XDDR_NOC_CH_MATCH_SHIFT			5
+#define XDDR_NOC_MOD_SEL_MASK			BIT(6)
+#define XDDR_NOC_MATCH_EN_MASK			BIT(8)
+
+#define ECCR_UE_CE_ADDR_LO_BP_MASK		GENMASK(2, 0)
+#define ECCR_UE_CE_ADDR_LO_LRANK_MASK		GENMASK(5, 3)
+#define ECCR_UE_CE_ADDR_LO_LRANK_SHIFT		3
+#define ECCR_UE_CE_ADDR_LO_RANK_MASK		GENMASK(7, 6)
+#define ECCR_UE_CE_ADDR_LO_RANK_SHIFT		6
+#define ECCR_UE_CE_ADDR_LO_GRP_MASK		GENMASK(9, 8)
+#define ECCR_UE_CE_ADDR_LO_GRP_SHIFT		8
+#define ECCR_UE_CE_ADDR_LO_BANK_MASK		GENMASK(11, 10)
+#define ECCR_UE_CE_ADDR_LO_BANK_SHIFT		10
+#define ECCR_UE_CE_ADDR_LO_COL_MASK		GENMASK(21, 12)
+#define ECCR_UE_CE_ADDR_LO_COL_SHIFT		12
+#define ECCR_UE_CE_ADDR_LO_ROW_MASK		GENMASK(31, 22)
+#define ECCR_UE_CE_ADDR_LO_ROW_SHIFT		22
+#define ECCR_UE_CE_ADDR_HI_ROW_MASK		GENMASK(7, 0)
+#define ECCR_UE_CE_ADDR_HI_ROW_SHIFT		10
+
+#define XDDR_EDAC_NR_CSROWS			1
+#define XDDR_EDAC_NR_CHANS			1
+
+#define XDDR_BUS_WIDTH_64			0
+#define XDDR_BUS_WIDTH_32			1
+#define XDDR_BUS_WIDTH_16			2
+
+#define ECC_CEPOISON_MASK			0x1
+#define ECC_UEPOISON_MASK			0x3
+
+#define XDDR_MAX_ROW_CNT			18
+#define XDDR_MAX_COL_CNT			10
+#define XDDR_MAX_RANK_CNT			2
+#define XDDR_MAX_LRANK_CNT			3
+#define XDDR_MAX_BANK_CNT			2
+#define XDDR_MAX_GRP_CNT			2
+
+#define PCSR_UNLOCK_VAL				0xF9E8D7C6
+#define XDDR_ERR_TYPE_CE			0
+#define XDDR_ERR_TYPE_UE			1
+
+#define XILINX_DRAM_SIZE_4G			0
+#define XILINX_DRAM_SIZE_6G			1
+#define XILINX_DRAM_SIZE_8G			2
+#define XILINX_DRAM_SIZE_12G			3
+#define XILINX_DRAM_SIZE_16G			4
+#define XILINX_DRAM_SIZE_32G			5
+
+/**
+ * struct xddr_ecc_error_info - ECC error log information.
+ * @rank:		Rank number.
+ * @lrank:		Logical Rank number.
+ * @row:		Row number.
+ * @col:		Column number.
+ * @bank:		Bank number.
+ * @group:		Group number.
+ * @burstpos:		Burst position.
+ */
+struct xddr_ecc_error_info {
+	u32 rank;
+	u32 lrank;
+	u32 row;
+	u32 col;
+	u32 bank;
+	u32 group;
+	u32 burstpos;
+};
+
+/**
+ * struct xddr_ecc_status - ECC status information to report.
+ * @ceinfo:	Correctable error log information.
+ * @ueinfo:	Uncorrectable error log information.
+ * @channel:	Channel number.
+ * @error_type:	Error type information.
+ */
+struct xddr_ecc_status {
+	struct xddr_ecc_error_info ceinfo[2];
+	struct xddr_ecc_error_info ueinfo[2];
+	u32 channel;
+	u8 error_type;
+};
+
+/**
+ * struct xddr_edac_priv - DDR memory controller private instance data.
+ * @ddrmc_baseaddr:	Base address of the DDR controller.
+ * @ddrmc_noc_baseaddr:	Base address of the DDRMC NOC.
+ * @message:		Buffer for framing the event specific info.
+ * @mc_id:		Memory controller ID.
+ * @ce_cnt:		Correctable error count.
+ * @ue_cnt:		UnCorrectable error count.
+ * @stat:		ECC status information.
+ * @lrank_bit:		Bit shifts for lrank bit.
+ * @rank_bit:		Bit shifts for rank bit.
+ * @row_bit:		Bit shifts for row bit.
+ * @col_bit:		Bit shifts for column bit.
+ * @bank_bit:		Bit shifts for bank bit.
+ * @grp_bit:		Bit shifts for group bit.
+ * @ch_bit:		Bit shifts for channel bit.
+ * @err_inject_addr:	Data poison address.
+ */
+struct xddr_edac_priv {
+	void __iomem *ddrmc_baseaddr;
+	void __iomem *ddrmc_noc_baseaddr;
+	char message[XDDR_EDAC_MSG_SIZE];
+	u32 mc_id;
+	u32 ce_cnt;
+	u32 ue_cnt;
+	struct xddr_ecc_status stat;
+	u32 lrank_bit[3];
+	u32 rank_bit[2];
+	u32 row_bit[18];
+	u32 col_bit[10];
+	u32 bank_bit[2];
+	u32 grp_bit[2];
+	u32 ch_bit;
+#ifdef CONFIG_EDAC_DEBUG
+	u64 err_inject_addr;
+#endif
+};
+
+/**
+ * xddr_get_error_info - Get the current ECC error info.
+ * @priv:	DDR memory controller private instance data.
+ *
+ * Return: one if there is no error otherwise returns zero.
+ */
+static int xddr_get_error_info(struct xddr_edac_priv *priv)
+{
+	struct xddr_ecc_status *p;
+	u32 eccr0_ceval, eccr1_ceval, eccr0_ueval, eccr1_ueval, regval;
+	void __iomem *ddrmc_base;
+
+	ddrmc_base = priv->ddrmc_baseaddr;
+	p = &priv->stat;
+
+	eccr0_ceval = readl(ddrmc_base + ECCR0_CERR_STAT_OFFSET);
+	eccr1_ceval = readl(ddrmc_base + ECCR1_CERR_STAT_OFFSET);
+	eccr0_ueval = readl(ddrmc_base + ECCR0_UERR_STAT_OFFSET);
+	eccr1_ueval = readl(ddrmc_base + ECCR1_UERR_STAT_OFFSET);
+
+	if (!eccr0_ceval && !eccr1_ceval && !eccr0_ueval && !eccr1_ueval)
+		return 1;
+	else if (!eccr0_ceval && !eccr1_ceval)
+		goto ue_err;
+	else if (!eccr0_ceval)
+		p->channel = 1;
+	else
+		p->channel = 0;
+
+	p->error_type = XDDR_ERR_TYPE_CE;
+	regval = readl(ddrmc_base + ECCR0_CE_ADDR_LO_OFFSET);
+	p->ceinfo[0].burstpos = (regval & ECCR_UE_CE_ADDR_LO_BP_MASK);
+	p->ceinfo[0].lrank = (regval & ECCR_UE_CE_ADDR_LO_LRANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_LRANK_SHIFT;
+	p->ceinfo[0].rank = (regval & ECCR_UE_CE_ADDR_LO_RANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_RANK_SHIFT;
+	p->ceinfo[0].group = (regval & ECCR_UE_CE_ADDR_LO_GRP_MASK) >>
+					ECCR_UE_CE_ADDR_LO_GRP_SHIFT;
+	p->ceinfo[0].bank = (regval & ECCR_UE_CE_ADDR_LO_BANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_BANK_SHIFT;
+	p->ceinfo[0].col = (regval & ECCR_UE_CE_ADDR_LO_COL_MASK) >>
+					ECCR_UE_CE_ADDR_LO_COL_SHIFT;
+	p->ceinfo[0].row = (regval & ECCR_UE_CE_ADDR_LO_ROW_MASK) >>
+					ECCR_UE_CE_ADDR_LO_ROW_SHIFT;
+	regval = readl(ddrmc_base + ECCR0_CE_ADDR_HI_OFFSET);
+	p->ceinfo[0].row |= ((regval & ECCR_UE_CE_ADDR_HI_ROW_MASK) <<
+					ECCR_UE_CE_ADDR_HI_ROW_SHIFT);
+
+	edac_dbg(2, "ERR DATA LOW: 0x%08X ERR DATA HIGH: 0x%08X ERR DATA PARITY: 0x%08X\n",
+		 readl(ddrmc_base + ECCR0_CE_DATA_LO_OFFSET),
+		 readl(ddrmc_base + ECCR0_CE_DATA_HI_OFFSET),
+		 readl(ddrmc_base + ECCR0_CE_DATA_PAR_OFFSET));
+
+	regval = readl(ddrmc_base + ECCR1_CE_ADDR_LO_OFFSET);
+	p->ceinfo[1].burstpos = (regval & ECCR_UE_CE_ADDR_LO_BP_MASK);
+	p->ceinfo[1].lrank = (regval & ECCR_UE_CE_ADDR_LO_LRANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_LRANK_SHIFT;
+	p->ceinfo[1].rank = (regval & ECCR_UE_CE_ADDR_LO_RANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_RANK_SHIFT;
+	p->ceinfo[1].group = (regval & ECCR_UE_CE_ADDR_LO_GRP_MASK) >>
+					ECCR_UE_CE_ADDR_LO_GRP_SHIFT;
+	p->ceinfo[1].bank = (regval & ECCR_UE_CE_ADDR_LO_BANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_BANK_SHIFT;
+	p->ceinfo[1].col = (regval & ECCR_UE_CE_ADDR_LO_COL_MASK) >>
+					ECCR_UE_CE_ADDR_LO_COL_SHIFT;
+	p->ceinfo[1].row = (regval & ECCR_UE_CE_ADDR_LO_ROW_MASK) >>
+					ECCR_UE_CE_ADDR_LO_ROW_SHIFT;
+	regval = readl(ddrmc_base + ECCR1_CE_ADDR_HI_OFFSET);
+	p->ceinfo[1].row |= ((regval & ECCR_UE_CE_ADDR_HI_ROW_MASK) <<
+					ECCR_UE_CE_ADDR_HI_ROW_SHIFT);
+
+	edac_dbg(2, "ERR DATA LOW: 0x%08X ERR DATA HIGH: 0x%08X ERR DATA PARITY: 0x%08X\n",
+		 readl(ddrmc_base + ECCR1_CE_DATA_LO_OFFSET),
+		 readl(ddrmc_base + ECCR1_CE_DATA_HI_OFFSET),
+		 readl(ddrmc_base + ECCR1_CE_DATA_PAR_OFFSET));
+ue_err:
+	if (!eccr0_ueval && !eccr1_ueval)
+		goto out;
+	else if (!eccr0_ueval)
+		p->channel = 1;
+	else
+		p->channel = 0;
+
+	p->error_type = XDDR_ERR_TYPE_UE;
+	regval = readl(ddrmc_base + ECCR0_UE_ADDR_LO_OFFSET);
+	p->ueinfo[0].burstpos = (regval & ECCR_UE_CE_ADDR_LO_BP_MASK);
+	p->ueinfo[0].lrank = (regval & ECCR_UE_CE_ADDR_LO_LRANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_LRANK_SHIFT;
+	p->ueinfo[0].rank = (regval & ECCR_UE_CE_ADDR_LO_RANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_RANK_SHIFT;
+	p->ueinfo[0].group = (regval & ECCR_UE_CE_ADDR_LO_GRP_MASK) >>
+					ECCR_UE_CE_ADDR_LO_GRP_SHIFT;
+	p->ueinfo[0].bank = (regval & ECCR_UE_CE_ADDR_LO_BANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_BANK_SHIFT;
+	p->ueinfo[0].col = (regval & ECCR_UE_CE_ADDR_LO_COL_MASK) >>
+					ECCR_UE_CE_ADDR_LO_COL_SHIFT;
+	p->ueinfo[0].row = (regval & ECCR_UE_CE_ADDR_LO_ROW_MASK) >>
+					ECCR_UE_CE_ADDR_LO_ROW_SHIFT;
+	regval = readl(ddrmc_base + ECCR0_UE_ADDR_HI_OFFSET);
+	p->ueinfo[0].row |= ((regval & ECCR_UE_CE_ADDR_HI_ROW_MASK) <<
+					ECCR_UE_CE_ADDR_HI_ROW_SHIFT);
+
+	edac_dbg(2, "ERR DATA LOW: 0x%08X ERR DATA HIGH: 0x%08X ERR DATA PARITY: 0x%08X\n",
+		 readl(ddrmc_base + ECCR0_UE_DATA_LO_OFFSET),
+		 readl(ddrmc_base + ECCR0_UE_DATA_HI_OFFSET),
+		 readl(ddrmc_base + ECCR0_UE_DATA_PAR_OFFSET));
+
+	regval = readl(ddrmc_base + ECCR1_UE_ADDR_LO_OFFSET);
+	p->ueinfo[1].burstpos = (regval & ECCR_UE_CE_ADDR_LO_BP_MASK);
+	p->ueinfo[1].lrank = (regval & ECCR_UE_CE_ADDR_LO_LRANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_LRANK_SHIFT;
+	p->ueinfo[1].rank = (regval & ECCR_UE_CE_ADDR_LO_RANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_RANK_SHIFT;
+	p->ueinfo[1].group = (regval & ECCR_UE_CE_ADDR_LO_GRP_MASK) >>
+					ECCR_UE_CE_ADDR_LO_GRP_SHIFT;
+	p->ueinfo[1].bank = (regval & ECCR_UE_CE_ADDR_LO_BANK_MASK) >>
+					ECCR_UE_CE_ADDR_LO_BANK_SHIFT;
+	p->ueinfo[1].col = (regval & ECCR_UE_CE_ADDR_LO_COL_MASK) >>
+					ECCR_UE_CE_ADDR_LO_COL_SHIFT;
+	p->ueinfo[1].row = (regval & ECCR_UE_CE_ADDR_LO_ROW_MASK) >>
+					ECCR_UE_CE_ADDR_LO_ROW_SHIFT;
+	regval = readl(ddrmc_base + ECCR1_UE_ADDR_HI_OFFSET);
+	p->ueinfo[1].row |= ((regval & ECCR_UE_CE_ADDR_HI_ROW_MASK) <<
+					ECCR_UE_CE_ADDR_HI_ROW_SHIFT);
+
+	edac_dbg(2, "ERR DATA LOW: 0x%08X ERR DATA HIGH: 0x%08X ERR DATA PARITY: 0x%08X\n",
+		 readl(ddrmc_base + ECCR1_UE_DATA_LO_OFFSET),
+		 readl(ddrmc_base + ECCR1_UE_DATA_HI_OFFSET),
+		 readl(ddrmc_base + ECCR1_UE_DATA_PAR_OFFSET));
+
+out:
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, ddrmc_base + XDDR_PCSR_OFFSET);
+
+	writel(0, ddrmc_base + ECCR0_CERR_STAT_OFFSET);
+	writel(0, ddrmc_base + ECCR1_CERR_STAT_OFFSET);
+	writel(0, ddrmc_base + ECCR0_UERR_STAT_OFFSET);
+	writel(0, ddrmc_base + ECCR1_UERR_STAT_OFFSET);
+
+	/* Lock the PCSR registers */
+	writel(1, ddrmc_base + XDDR_PCSR_OFFSET);
+
+	return 0;
+}
+
+/**
+ * xddr_convert_to_physical - Convert to physical address.
+ * @priv:	DDR memory controller private instance data.
+ * @pinf:	ECC error info structure.
+ *
+ * Return: Physical address of the DDR memory.
+ */
+static ulong xddr_convert_to_physical(struct xddr_edac_priv *priv,
+				      struct xddr_ecc_error_info pinf)
+{
+	ulong err_addr = 0;
+	u32 index;
+
+	for (index = 0; index < XDDR_MAX_ROW_CNT; index++) {
+		err_addr |= (pinf.row & BIT(0)) << priv->row_bit[index];
+		pinf.row >>= 1;
+	}
+
+	for (index = 0; index < XDDR_MAX_COL_CNT; index++) {
+		err_addr |= (pinf.col & BIT(0)) << priv->col_bit[index];
+		pinf.col >>= 1;
+	}
+
+	for (index = 0; index < XDDR_MAX_BANK_CNT; index++) {
+		err_addr |= (pinf.bank & BIT(0)) << priv->bank_bit[index];
+		pinf.bank >>= 1;
+	}
+
+	for (index = 0; index < XDDR_MAX_GRP_CNT; index++) {
+		err_addr |= (pinf.group & BIT(0)) << priv->grp_bit[index];
+		pinf.group >>= 1;
+	}
+
+	for (index = 0; index < XDDR_MAX_RANK_CNT; index++) {
+		err_addr |= (pinf.rank & BIT(0)) << priv->rank_bit[index];
+		pinf.rank >>= 1;
+	}
+
+	for (index = 0; index < XDDR_MAX_LRANK_CNT; index++) {
+		err_addr |= (pinf.lrank & BIT(0)) << priv->lrank_bit[index];
+		pinf.lrank >>= 1;
+	}
+
+	err_addr |= (priv->stat.channel & BIT(0)) << priv->ch_bit;
+
+	return err_addr;
+}
+
+/**
+ * xddr_handle_error - Handle Correctable and Uncorrectable errors.
+ * @mci:	EDAC memory controller instance.
+ * @stat:	ECC status structure.
+ *
+ * Handles ECC correctable and uncorrectable errors.
+ */
+static void xddr_handle_error(struct mem_ctl_info *mci,
+			      struct xddr_ecc_status *stat)
+{
+	struct xddr_edac_priv *priv = mci->pvt_info;
+	struct xddr_ecc_error_info pinf;
+
+	if (stat->error_type == XDDR_ERR_TYPE_CE) {
+		priv->ce_cnt++;
+		pinf = stat->ceinfo[stat->channel];
+		snprintf(priv->message, XDDR_EDAC_MSG_SIZE,
+			 "Error type:%s MC ID: %d Addr at %lx Burst Pos: %d\n",
+			 "CE", priv->mc_id,
+			 xddr_convert_to_physical(priv, pinf), pinf.burstpos);
+
+		edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci,
+				     priv->ce_cnt, 0, 0, 0, 0, 0, -1,
+				     priv->message, "");
+	}
+
+	if (stat->error_type == XDDR_ERR_TYPE_UE) {
+		priv->ue_cnt++;
+		pinf = stat->ueinfo[stat->channel];
+		snprintf(priv->message, XDDR_EDAC_MSG_SIZE,
+			 "Error type:%s MC ID: %d Addr at %lx Burst Pos: %d\n",
+			 "UE", priv->mc_id,
+			 xddr_convert_to_physical(priv, pinf), pinf.burstpos);
+
+		edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci,
+				     priv->ue_cnt, 0, 0, 0, 0, 0, -1,
+				     priv->message, "");
+	}
+
+	memset(stat, 0, sizeof(*stat));
+}
+
+/**
+ * xddr_intr_handler - Interrupt Handler for ECC interrupts.
+ * @irq:	IRQ number
+ * @dev_id:	Device ID
+ *
+ * Return: IRQ_NONE, if interrupt not set or IRQ_HANDLED otherwise.
+ */
+static irqreturn_t xddr_intr_handler(int irq, void *dev_id)
+{
+	struct mem_ctl_info *mci = dev_id;
+	struct xddr_edac_priv *priv;
+	int status, regval;
+
+	priv = mci->pvt_info;
+	regval = readl(priv->ddrmc_baseaddr + XDDR_ISR_OFFSET);
+	regval &= (XDDR_IRQ_CE_MASK | XDDR_IRQ_UE_MASK);
+	if (!regval)
+		return IRQ_NONE;
+
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	/* Clear the ISR */
+	writel(regval, priv->ddrmc_baseaddr + XDDR_ISR_OFFSET);
+
+	/* Lock the PCSR registers */
+	writel(1, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	status = xddr_get_error_info(priv);
+	if (status)
+		return IRQ_NONE;
+
+	xddr_handle_error(mci, &priv->stat);
+
+	edac_dbg(3, "Total error count CE %d UE %d\n",
+		 priv->ce_cnt, priv->ue_cnt);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xddr_err_callback - Handle Correctable and Uncorrectable errors.
+ * @payload:	payload data.
+ * @data:	mci controller data.
+ *
+ * Handles ECC correctable and uncorrectable errors.
+ */
+static void xddr_err_callback(const u32 *payload, void *data)
+{
+	struct mem_ctl_info *mci = (struct mem_ctl_info *)data;
+	struct xddr_edac_priv *priv;
+	int status, regval;
+	struct xddr_ecc_status *p;
+
+	priv = mci->pvt_info;
+	p = &priv->stat;
+
+	regval = readl(priv->ddrmc_baseaddr + XDDR_ISR_OFFSET);
+	regval &= (XDDR_IRQ_CE_MASK | XDDR_IRQ_UE_MASK);
+	if (!regval)
+		return;
+
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	/* Clear the ISR */
+	writel(regval, priv->ddrmc_baseaddr + XDDR_ISR_OFFSET);
+	/* Lock the PCSR registers */
+
+	writel(1, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+	if (payload[2] == XPM_EVENT_ERROR_MASK_DDRMC_CR)
+		p->error_type = XDDR_ERR_TYPE_CE;
+	if (payload[2] == XPM_EVENT_ERROR_MASK_DDRMC_NCR)
+		p->error_type = XDDR_ERR_TYPE_UE;
+
+	status = xddr_get_error_info(priv);
+	if (status)
+		return;
+
+	xddr_handle_error(mci, &priv->stat);
+
+	edac_dbg(3, "Total error count CE %d UE %d\n",
+		 priv->ce_cnt, priv->ue_cnt);
+}
+
+/**
+ * xddr_get_dwidth - Return the controller memory width.
+ * @base:	DDR memory controller base address.
+ *
+ * Get the EDAC device type width appropriate for the controller
+ * configuration.
+ *
+ * Return: a device type width enumeration.
+ */
+static enum dev_type xddr_get_dwidth(const void __iomem *base)
+{
+	enum dev_type dt;
+	u32 regval;
+
+	regval = readl(base + XDDR_REG_CONFIG0_OFFSET);
+	regval = (regval & XDDR_REG_CONFIG0_BUS_WIDTH_MASK) >>
+				XDDR_REG_CONFIG0_BUS_WIDTH_SHIFT;
+	switch (regval) {
+	case XDDR_BUS_WIDTH_16:
+		dt = DEV_X2;
+		break;
+	case XDDR_BUS_WIDTH_32:
+		dt = DEV_X4;
+		break;
+	case XDDR_BUS_WIDTH_64:
+		dt = DEV_X8;
+		break;
+	default:
+		dt = DEV_UNKNOWN;
+	}
+
+	return dt;
+}
+
+/**
+ * xddr_get_ecc_state - Return the controller ECC enable/disable status.
+ * @base:	DDR memory controller base address.
+ *
+ * Get the ECC enable/disable status for the controller.
+ *
+ * Return: a ECC status boolean i.e true/false - enabled/disabled.
+ */
+static bool xddr_get_ecc_state(void __iomem *base)
+{
+	enum dev_type dt;
+	u32 ecctype;
+
+	dt = xddr_get_dwidth(base);
+	if (dt == DEV_UNKNOWN)
+		return false;
+
+	ecctype = readl(base + XDDR_REG_PINOUT_OFFSET);
+	ecctype &= XDDR_REG_PINOUT_ECC_EN_MASK;
+	if (ecctype)
+		return true;
+
+	return false;
+}
+
+/**
+ * xddr_get_memsize - Get the size of the attached memory device.
+ * @priv:	DDR memory controller private instance data.
+ *
+ * Return: the memory size in bytes.
+ */
+static u64 xddr_get_memsize(struct xddr_edac_priv *priv)
+{
+	u64 size;
+	u32 regval;
+
+	regval = readl(priv->ddrmc_baseaddr + XDDR_REG_CONFIG0_OFFSET) &
+				XDDR_REG_CONFIG0_SIZE_MASK;
+	regval >>= XDDR_REG_CONFIG0_SIZE_SHIFT;
+	switch (regval) {
+	case XILINX_DRAM_SIZE_4G:
+		size = (4U * SZ_1G);
+		break;
+	case XILINX_DRAM_SIZE_6G:
+		size = (6U * SZ_1G);
+		break;
+	case XILINX_DRAM_SIZE_8G:
+		size = (8U * SZ_1G);
+		break;
+	case XILINX_DRAM_SIZE_12G:
+		size = (12U * SZ_1G);
+		break;
+	case XILINX_DRAM_SIZE_16G:
+		size = (16U * SZ_1G);
+		break;
+	case XILINX_DRAM_SIZE_32G:
+		size = (32U * SZ_1G);
+		break;
+	default:
+		/* Invalid configuration */
+		size = 0;
+		break;
+	}
+
+	return size;
+}
+
+/**
+ * xddr_init_csrows - Initialize the csrow data.
+ * @mci:	EDAC memory controller instance.
+ *
+ * Initialize the chip select rows associated with the EDAC memory
+ * controller instance.
+ */
+static void xddr_init_csrows(struct mem_ctl_info *mci)
+{
+	struct xddr_edac_priv *priv = mci->pvt_info;
+	struct csrow_info *csi;
+	struct dimm_info *dimm;
+	u32 row;
+	int ch;
+	unsigned long size;
+
+	size = xddr_get_memsize(priv);
+	for (row = 0; row < mci->nr_csrows; row++) {
+		csi = mci->csrows[row];
+		for (ch = 0; ch < csi->nr_channels; ch++) {
+			dimm = csi->channels[ch]->dimm;
+			dimm->edac_mode	= EDAC_SECDED;
+			dimm->mtype = MEM_DDR4;
+			dimm->nr_pages = (size >> PAGE_SHIFT) /
+						csi->nr_channels;
+			dimm->grain = XDDR_EDAC_ERR_GRAIN;
+			dimm->dtype = xddr_get_dwidth(priv->ddrmc_baseaddr);
+		}
+	}
+}
+
+/**
+ * xddr_mc_init - Initialize one driver instance.
+ * @mci:	EDAC memory controller instance.
+ * @pdev:	platform device.
+ *
+ * Perform initialization of the EDAC memory controller instance and
+ * related driver-private data associated with the memory controller the
+ * instance is bound to.
+ */
+static void xddr_mc_init(struct mem_ctl_info *mci, struct platform_device *pdev)
+{
+	mci->pdev = &pdev->dev;
+	platform_set_drvdata(pdev, mci);
+
+	/* Initialize controller capabilities and configuration */
+	mci->mtype_cap = MEM_FLAG_DDR4;
+	mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_SECDED;
+	mci->scrub_cap = SCRUB_HW_SRC;
+	mci->scrub_mode = SCRUB_NONE;
+
+	mci->edac_cap = EDAC_FLAG_SECDED;
+	mci->ctl_name = "xlnx_ddr_controller";
+	mci->dev_name = dev_name(&pdev->dev);
+	mci->mod_name = "xlnx_edac";
+
+	edac_op_state = EDAC_OPSTATE_INT;
+
+	xddr_init_csrows(mci);
+}
+
+static void xddr_enable_intr(struct xddr_edac_priv *priv)
+{
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	/* Enable UE and CE Interrupts to support the interrupt case */
+	writel(XDDR_IRQ_CE_MASK | XDDR_IRQ_UE_MASK,
+	       priv->ddrmc_baseaddr + XDDR_IRQ_EN_OFFSET);
+
+	writel(XDDR_IRQ_UE_MASK,
+	       priv->ddrmc_baseaddr + XDDR_IRQ1_EN_OFFSET);
+	/* Lock the PCSR registers */
+	writel(1, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+}
+
+static void xddr_disable_intr(struct xddr_edac_priv *priv)
+{
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	/* Disable UE/CE Interrupts */
+	writel(XDDR_IRQ_CE_MASK | XDDR_IRQ_UE_MASK,
+	       priv->ddrmc_baseaddr + XDDR_IRQ_DIS_OFFSET);
+
+	/* Lock the PCSR registers */
+	writel(1, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+}
+
+static int xddr_setup_irq(struct mem_ctl_info *mci,
+			  struct platform_device *pdev)
+{
+	int ret, irq;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		edac_printk(KERN_ERR, EDAC_MC,
+			    "No IRQ %d in DT\n", irq);
+		return irq;
+	}
+
+	ret = devm_request_irq(&pdev->dev, irq, xddr_intr_handler,
+			       IRQF_SHARED, dev_name(&pdev->dev), mci);
+	if (ret < 0) {
+		edac_printk(KERN_ERR, EDAC_MC, "Failed to request IRQ\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_EDAC_DEBUG
+#define to_mci(k) container_of(k, struct mem_ctl_info, dev)
+
+/**
+ * xddr_poison_setup - Update poison registers.
+ * @priv:	DDR memory controller private instance data.
+ *
+ * Update poison registers as per DDR mapping.
+ * Return: none.
+ */
+static void xddr_poison_setup(struct xddr_edac_priv *priv)
+{
+	u32 col = 0, row = 0, bank = 0, grp = 0, rank = 0, lrank = 0, ch = 0;
+	u32 index, regval;
+
+	for (index = 0; index < XDDR_MAX_ROW_CNT; index++) {
+		row |= (((priv->err_inject_addr >> priv->row_bit[index]) &
+						BIT(0)) << index);
+	}
+
+	for (index = 0; index < XDDR_MAX_COL_CNT; index++) {
+		col |= (((priv->err_inject_addr >> priv->col_bit[index]) &
+						BIT(0)) << index);
+	}
+
+	for (index = 0; index < XDDR_MAX_BANK_CNT; index++) {
+		bank |= (((priv->err_inject_addr >> priv->bank_bit[index]) &
+						BIT(0)) << index);
+	}
+
+	for (index = 0; index < XDDR_MAX_GRP_CNT; index++) {
+		grp |= (((priv->err_inject_addr >> priv->grp_bit[index]) &
+						BIT(0)) << index);
+	}
+
+	for (index = 0; index < XDDR_MAX_RANK_CNT; index++) {
+		rank |= (((priv->err_inject_addr >> priv->rank_bit[index]) &
+						BIT(0)) << index);
+	}
+
+	for (index = 0; index < XDDR_MAX_LRANK_CNT; index++) {
+		lrank |= (((priv->err_inject_addr >> priv->lrank_bit[index]) &
+						BIT(0)) << index);
+	}
+
+	ch = (priv->err_inject_addr >> priv->ch_bit) & BIT(0);
+	if (ch)
+		writel(0xFF, priv->ddrmc_baseaddr + ECCW1_FLIP_CTRL);
+	else
+		writel(0xFF, priv->ddrmc_baseaddr + ECCW0_FLIP_CTRL);
+
+	writel(0, priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC12_OFFSET);
+	writel(0, priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC13_OFFSET);
+
+	regval = (row & XDDR_NOC_ROW_MATCH_MASK);
+	regval |= (col << XDDR_NOC_COL_MATCH_SHIFT) & XDDR_NOC_COL_MATCH_MASK;
+	regval |= (bank << XDDR_NOC_BANK_MATCH_SHIFT) &
+			XDDR_NOC_BANK_MATCH_MASK;
+	regval |= (grp << XDDR_NOC_GRP_MATCH_SHIFT) & XDDR_NOC_GRP_MATCH_MASK;
+	writel(regval, priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC14_OFFSET);
+
+	regval = (rank & XDDR_NOC_RANK_MATCH_MASK);
+	regval |= (lrank << XDDR_NOC_LRANK_MATCH_SHIFT) &
+			XDDR_NOC_LRANK_MATCH_MASK;
+	regval |= (ch << XDDR_NOC_CH_MATCH_SHIFT) & XDDR_NOC_CH_MATCH_MASK;
+	regval |= (XDDR_NOC_MOD_SEL_MASK | XDDR_NOC_MATCH_EN_MASK);
+	writel(regval, priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC15_OFFSET);
+}
+
+static ssize_t inject_data_error_show(struct device *dev,
+				      struct device_attribute *mattr,
+				      char *data)
+{
+	struct mem_ctl_info *mci = to_mci(dev);
+	struct xddr_edac_priv *priv = mci->pvt_info;
+
+	return sprintf(data, "Error injection Address: 0x%llx\n\r",
+			priv->err_inject_addr);
+}
+
+static ssize_t inject_data_error_store(struct device *dev,
+				       struct device_attribute *mattr,
+				       const char *data, size_t count)
+{
+	struct mem_ctl_info *mci = to_mci(dev);
+	struct xddr_edac_priv *priv = mci->pvt_info;
+
+	if (kstrtoull(data, 0, &priv->err_inject_addr))
+		return -EINVAL;
+
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_noc_baseaddr + XDDR_PCSR_OFFSET);
+
+	xddr_poison_setup(priv);
+
+	/* Lock the PCSR registers */
+	writel(1, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+	writel(1, priv->ddrmc_noc_baseaddr + XDDR_PCSR_OFFSET);
+
+	return count;
+}
+
+static ssize_t inject_data_poison_show(struct device *dev,
+				       struct device_attribute *mattr,
+				       char *data)
+{
+	struct mem_ctl_info *mci = to_mci(dev);
+	struct xddr_edac_priv *priv = mci->pvt_info;
+	u32 regval;
+
+	regval = readl(priv->ddrmc_baseaddr + ECCW0_FLIP0_OFFSET);
+	return sprintf(data, "Data Poisoning: %s\n\r",
+			((regval & 0x3) == 1)
+			? ("Correctable Error") : ("UnCorrectable Error"));
+}
+
+static ssize_t inject_data_poison_store(struct device *dev,
+					struct device_attribute *mattr,
+					const char *data, size_t count)
+{
+	struct mem_ctl_info *mci = to_mci(dev);
+	struct xddr_edac_priv *priv = mci->pvt_info;
+
+	/* Unlock the PCSR registers */
+	writel(PCSR_UNLOCK_VAL, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	writel(0, priv->ddrmc_baseaddr + ECCW0_FLIP0_OFFSET);
+	writel(0, priv->ddrmc_baseaddr + ECCW1_FLIP0_OFFSET);
+	if (strncmp(data, "CE", 2) == 0) {
+		writel(ECC_CEPOISON_MASK, priv->ddrmc_baseaddr +
+		       ECCW0_FLIP0_OFFSET);
+		writel(ECC_CEPOISON_MASK, priv->ddrmc_baseaddr +
+		       ECCW1_FLIP0_OFFSET);
+	} else {
+		writel(ECC_UEPOISON_MASK, priv->ddrmc_baseaddr +
+		       ECCW0_FLIP0_OFFSET);
+		writel(ECC_UEPOISON_MASK, priv->ddrmc_baseaddr +
+		       ECCW1_FLIP0_OFFSET);
+	}
+
+	/* Lock the PCSR registers */
+	writel(1, priv->ddrmc_baseaddr + XDDR_PCSR_OFFSET);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(inject_data_error);
+static DEVICE_ATTR_RW(inject_data_poison);
+
+static int edac_create_sysfs_attributes(struct mem_ctl_info *mci)
+{
+	int rc;
+
+	rc = device_create_file(&mci->dev, &dev_attr_inject_data_error);
+	if (rc < 0)
+		return rc;
+
+	rc = device_create_file(&mci->dev, &dev_attr_inject_data_poison);
+	if (rc < 0)
+		return rc;
+
+	return 0;
+}
+
+static void edac_remove_sysfs_attributes(struct mem_ctl_info *mci)
+{
+	device_remove_file(&mci->dev, &dev_attr_inject_data_error);
+	device_remove_file(&mci->dev, &dev_attr_inject_data_poison);
+}
+
+static void xddr_setup_row_address_map(struct xddr_edac_priv *priv)
+{
+	u32 regval;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC5_OFFSET);
+	priv->row_bit[0] = regval & ROW_0_MASK;
+	priv->row_bit[1] = (regval & ROW_1_MASK) >> ROW_1_SHIFT;
+	priv->row_bit[2] = (regval & ROW_2_MASK) >> ROW_2_SHIFT;
+	priv->row_bit[3] = (regval & ROW_3_MASK) >> ROW_3_SHIFT;
+	priv->row_bit[4] = (regval & ROW_4_MASK) >> ROW_4_SHIFT;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC6_OFFSET);
+	priv->row_bit[5] = regval & ROW_5_MASK;
+	priv->row_bit[6] = (regval & ROW_6_MASK) >> ROW_6_SHIFT;
+	priv->row_bit[7] = (regval & ROW_7_MASK) >> ROW_7_SHIFT;
+	priv->row_bit[8] = (regval & ROW_8_MASK) >> ROW_8_SHIFT;
+	priv->row_bit[9] = (regval & ROW_9_MASK) >> ROW_9_SHIFT;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC7_OFFSET);
+	priv->row_bit[10] = regval & ROW_10_MASK;
+	priv->row_bit[11] = (regval & ROW_11_MASK) >> ROW_11_SHIFT;
+	priv->row_bit[12] = (regval & ROW_12_MASK) >> ROW_12_SHIFT;
+	priv->row_bit[13] = (regval & ROW_13_MASK) >> ROW_13_SHIFT;
+	priv->row_bit[14] = (regval & ROW_14_MASK) >> ROW_14_SHIFT;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC8_OFFSET);
+
+	priv->row_bit[15] = regval & ROW_15_MASK;
+	priv->row_bit[16] = (regval & ROW_16_MASK) >> ROW_16_SHIFT;
+	priv->row_bit[17] = (regval & ROW_17_MASK) >> ROW_17_SHIFT;
+}
+
+static void xddr_setup_column_address_map(struct xddr_edac_priv *priv)
+{
+	u32 regval;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC8_OFFSET);
+	priv->col_bit[0] = (regval & COL_0_MASK) >> COL_0_SHIFT;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC9_OFFSET);
+	priv->col_bit[1] = (regval & COL_1_MASK);
+	priv->col_bit[2] = (regval & COL_2_MASK) >> COL_2_SHIFT;
+	priv->col_bit[3] = (regval & COL_3_MASK) >> COL_3_SHIFT;
+	priv->col_bit[4] = (regval & COL_4_MASK) >> COL_4_SHIFT;
+	priv->col_bit[5] = (regval & COL_5_MASK) >> COL_5_SHIFT;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC10_OFFSET);
+	priv->col_bit[6] = (regval & COL_6_MASK);
+	priv->col_bit[7] = (regval & COL_7_MASK) >> COL_7_SHIFT;
+	priv->col_bit[8] = (regval & COL_8_MASK) >> COL_8_SHIFT;
+	priv->col_bit[9] = (regval & COL_9_MASK) >> COL_9_SHIFT;
+}
+
+static void xddr_setup_bank_grp_ch_address_map(struct xddr_edac_priv *priv)
+{
+	u32 regval;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC10_OFFSET);
+	priv->bank_bit[0] = (regval & BANK_0_MASK) >> BANK_0_SHIFT;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC11_OFFSET);
+	priv->bank_bit[1] = (regval & BANK_1_MASK);
+	priv->grp_bit[0] = (regval & GRP_0_MASK) >> GRP_0_SHIFT;
+	priv->grp_bit[1] = (regval & GRP_1_MASK) >> GRP_1_SHIFT;
+	priv->ch_bit = (regval & CH_0_MASK) >> CH_0_SHIFT;
+}
+
+static void xddr_setup_rank_lrank_address_map(struct xddr_edac_priv *priv)
+{
+	u32 regval;
+
+	regval = readl(priv->ddrmc_noc_baseaddr + XDDR_NOC_REG_ADEC4_OFFSET);
+	priv->rank_bit[0] = (regval & RANK_0_MASK);
+	priv->rank_bit[1] = (regval & RANK_1_MASK) >> RANK_1_SHIFT;
+	priv->lrank_bit[0] = (regval & LRANK_0_MASK) >> LRANK_0_SHIFT;
+	priv->lrank_bit[1] = (regval & LRANK_1_MASK) >> LRANK_1_SHIFT;
+	priv->lrank_bit[2] = (regval & LRANK_2_MASK) >> LRANK_2_SHIFT;
+}
+
+/**
+ * xddr_setup_address_map - Set Address Map by querying ADDRMAP registers.
+ * @priv:	DDR memory controller private instance data.
+ *
+ * Set Address Map by querying ADDRMAP registers.
+ *
+ * Return: none.
+ */
+static void xddr_setup_address_map(struct xddr_edac_priv *priv)
+{
+	xddr_setup_row_address_map(priv);
+
+	xddr_setup_column_address_map(priv);
+
+	xddr_setup_bank_grp_ch_address_map(priv);
+
+	xddr_setup_rank_lrank_address_map(priv);
+}
+#endif /* CONFIG_EDAC_DEBUG */
+
+/**
+ * xddr_mc_probe - Check controller and bind driver.
+ * @pdev:	platform device.
+ *
+ * Probe a specific controller instance for binding with the driver.
+ *
+ * Return: 0 if the controller instance was successfully bound to the
+ * driver; otherwise, < 0 on error.
+ */
+static int xddr_mc_probe(struct platform_device *pdev)
+{
+	struct edac_mc_layer layers[2];
+	struct xddr_edac_priv *priv;
+	struct mem_ctl_info *mci;
+	void __iomem *ddrmc_baseaddr, *ddrmc_noc_baseaddr;
+	struct resource *res;
+	int rc;
+	u8 num_chans, num_csrows;
+	u32 edac_mc_id, regval;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ddrmc_base");
+	ddrmc_baseaddr = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ddrmc_baseaddr))
+		return PTR_ERR(ddrmc_baseaddr);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					   "ddrmc_noc_base");
+	ddrmc_noc_baseaddr = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ddrmc_noc_baseaddr))
+		return PTR_ERR(ddrmc_noc_baseaddr);
+
+	if (!xddr_get_ecc_state(ddrmc_baseaddr))
+		return -ENXIO;
+
+	rc = of_property_read_u32(pdev->dev.of_node, "xlnx,mc-id",
+				  &edac_mc_id);
+	if (rc)
+		return rc;
+
+	regval = readl(ddrmc_baseaddr + XDDR_REG_CONFIG0_OFFSET);
+	num_chans = (regval & XDDR_REG_CONFIG0_NUM_CHANS_MASK) >>
+			XDDR_REG_CONFIG0_NUM_CHANS_SHIFT;
+	num_chans++;
+
+	num_csrows = (regval & XDDR_REG_CONFIG0_NUM_RANKS_MASK) >>
+			XDDR_REG_CONFIG0_NUM_RANKS_SHIFT;
+	num_csrows *= 2;
+	if (!num_csrows)
+		num_csrows = 1;
+
+	layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
+	layers[0].size = num_csrows;
+	layers[0].is_virt_csrow = true;
+	layers[1].type = EDAC_MC_LAYER_CHANNEL;
+	layers[1].size = num_chans;
+	layers[1].is_virt_csrow = false;
+
+	mci = edac_mc_alloc(edac_mc_id, ARRAY_SIZE(layers), layers,
+			    sizeof(struct xddr_edac_priv));
+	if (!mci) {
+		edac_printk(KERN_ERR, EDAC_MC,
+			    "Failed memory allocation for mc instance\n");
+		return -ENOMEM;
+	}
+
+	priv = mci->pvt_info;
+	priv->ddrmc_baseaddr = ddrmc_baseaddr;
+	priv->ddrmc_noc_baseaddr = ddrmc_noc_baseaddr;
+	priv->ce_cnt = 0;
+	priv->ue_cnt = 0;
+
+	xddr_mc_init(mci, pdev);
+
+	rc = edac_mc_add_mc(mci);
+	if (rc) {
+		edac_printk(KERN_ERR, EDAC_MC,
+			    "Failed to register with EDAC core\n");
+		goto free_edac_mc;
+	}
+
+#ifdef CONFIG_EDAC_DEBUG
+	if (edac_create_sysfs_attributes(mci)) {
+		edac_printk(KERN_ERR, EDAC_MC,
+			    "Failed to create sysfs entries\n");
+		goto del_edac_mc;
+	}
+
+	xddr_setup_address_map(priv);
+#endif
+	if (disable_event) {
+		rc = xddr_setup_irq(mci, pdev);
+		if (rc)
+			goto del_edac_mc;
+	} else {
+		rc = xlnx_register_event(PM_NOTIFY_CB, XPM_NODETYPE_EVENT_ERROR_PMC_ERR1,
+					 XPM_EVENT_ERROR_MASK_DDRMC_CR |
+					 XPM_EVENT_ERROR_MASK_DDRMC_NCR,
+					 false, xddr_err_callback, mci);
+		if (rc == -ENODEV) {
+			rc = xddr_setup_irq(mci, pdev);
+			if (rc)
+				goto del_edac_mc;
+		}
+		if (rc) {
+			if (rc == -EACCES)
+				rc = -EPROBE_DEFER;
+
+			goto del_edac_mc;
+		}
+	}
+
+	xddr_enable_intr(priv);
+
+	return rc;
+
+del_edac_mc:
+	edac_mc_del_mc(&pdev->dev);
+free_edac_mc:
+	edac_mc_free(mci);
+
+	return rc;
+}
+
+/**
+ * xddr_mc_remove - Unbind driver from controller.
+ * @pdev:	Platform device.
+ *
+ * Return: Unconditionally 0
+ */
+static int xddr_mc_remove(struct platform_device *pdev)
+{
+	struct mem_ctl_info *mci = platform_get_drvdata(pdev);
+	struct xddr_edac_priv *priv = mci->pvt_info;
+
+	xddr_disable_intr(priv);
+
+#ifdef CONFIG_EDAC_DEBUG
+	edac_remove_sysfs_attributes(mci);
+#endif
+
+	if (!disable_event)
+		xlnx_unregister_event(PM_NOTIFY_CB, XPM_NODETYPE_EVENT_ERROR_PMC_ERR1,
+				      XPM_EVENT_ERROR_MASK_DDRMC_CR |
+				      XPM_EVENT_ERROR_MASK_DDRMC_NCR, xddr_err_callback);
+	edac_mc_del_mc(&pdev->dev);
+	edac_mc_free(mci);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_edac_match[] = {
+	{ .compatible = "xlnx,versal-ddrmc-edac", },
+	{
+		/* end of table */
+	}
+};
+
+MODULE_DEVICE_TABLE(of, xlnx_edac_match);
+
+static struct platform_driver xilinx_ddr_edac_mc_driver = {
+	.driver = {
+		.name = "xilinx-ddrmc-edac",
+		.of_match_table = xlnx_edac_match,
+	},
+	.probe = xddr_mc_probe,
+	.remove = xddr_mc_remove,
+};
+
+module_platform_driver(xilinx_ddr_edac_mc_driver);
+
+MODULE_AUTHOR("Xilinx Inc");
+MODULE_DESCRIPTION("Xilinx DDRMC ECC driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/edac/zynqmp_ocm_edac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/edac/zynqmp_ocm_edac.c
@@ -0,0 +1,638 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ZynqMP OCM ECC Driver
+ * This driver is based on mpc85xx_edac.c drivers
+ *
+ * Copyright (C) 2016 - 2021 Xilinx, Inc.
+ */
+
+#include <linux/edac.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+
+#include "edac_module.h"
+
+#define ZYNQMP_OCM_EDAC_MSG_SIZE	256
+
+#define ZYNQMP_OCM_EDAC_STRING	"zynqmp_ocm"
+#define ZYNQMP_OCM_EDAC_MOD_VER	"1"
+
+/* Controller registers */
+#define CTRL_OFST		0x0
+#define OCM_ISR_OFST		0x04
+#define OCM_IMR_OFST		0x08
+#define OCM_IEN_OFST		0x0C
+#define OCM_IDS_OFST		0x10
+
+/* ECC control register */
+#define ECC_CTRL_OFST		0x14
+
+/* Correctable error info registers */
+#define CE_FFA_OFST		0x1C
+#define CE_FFD0_OFST		0x20
+#define CE_FFD1_OFST		0x24
+#define CE_FFD2_OFST		0x28
+#define CE_FFD3_OFST		0x2C
+#define CE_FFE_OFST		0x30
+
+/* Uncorrectable error info registers */
+#define UE_FFA_OFST		0x34
+#define UE_FFD0_OFST		0x38
+#define UE_FFD1_OFST		0x3C
+#define UE_FFD2_OFST		0x40
+#define UE_FFD3_OFST		0x44
+#define UE_FFE_OFST		0x48
+
+/* ECC control register bit field definitions */
+#define ECC_CTRL_CLR_CE_ERR	0x40
+#define ECC_CTRL_CLR_UE_ERR	0x80
+
+/* Fault injection data and count registers */
+#define OCM_FID0_OFST		0x4C
+#define OCM_FID1_OFST		0x50
+#define OCM_FID2_OFST		0x54
+#define OCM_FID3_OFST		0x58
+#define OCM_FIC_OFST		0x74
+
+/* Interrupt masks */
+#define OCM_CEINTR_MASK	0x40
+#define OCM_UEINTR_MASK	0x80
+#define OCM_ECC_ENABLE_MASK	0x1
+#define OCM_FICOUNT_MASK	0x0FFFFFFF
+#define OCM_BASEVAL	0xFFFC0000
+#define EDAC_DEVICE "ZynqMP-OCM"
+#define OCM_CEUE_MASK	0xC0
+
+/**
+ * struct ecc_error_info - ECC error log information
+ * @addr:	Fault generated at this address
+ * @data0:	Generated fault data
+ * @data1:	Generated fault data
+ */
+struct ecc_error_info {
+	u32 addr;
+	u32 data0;
+	u32 data1;
+};
+
+/**
+ * struct zynqmp_ocm_ecc_status - ECC status information to report
+ * @ce_cnt:	Correctable error count
+ * @ue_cnt:	Uncorrectable error count
+ * @ceinfo:	Correctable error log information
+ * @ueinfo:	Uncorrectable error log information
+ */
+struct zynqmp_ocm_ecc_status {
+	u32 ce_cnt;
+	u32 ue_cnt;
+	struct ecc_error_info ceinfo;
+	struct ecc_error_info ueinfo;
+};
+
+/**
+ * struct zynqmp_ocm_edac_priv - DDR memory controller private instance data
+ * @baseaddr:	Base address of the DDR controller
+ * @message:	Buffer for framing the event specific info
+ * @stat:	ECC status information
+ * @p_data:	Pointer to platform data
+ * @ce_cnt:	Correctable Error count
+ * @ue_cnt:	Uncorrectable Error count
+ * @ce_bitpos:	Bit position for Correctable Error
+ * @ue_bitpos0:	First bit position for Uncorrectable Error
+ * @ue_bitpos1:	Second bit position for Uncorrectable Error
+ */
+struct zynqmp_ocm_edac_priv {
+	void __iomem *baseaddr;
+	char message[ZYNQMP_OCM_EDAC_MSG_SIZE];
+	struct zynqmp_ocm_ecc_status stat;
+	const struct zynqmp_ocm_platform_data *p_data;
+	u32 ce_cnt;
+	u32 ue_cnt;
+	u8 ce_bitpos;
+	u8 ue_bitpos0;
+	u8 ue_bitpos1;
+};
+
+/**
+ * zynqmp_ocm_edac_geterror_info - Get the current ecc error info
+ * @base:	Pointer to the base address of the ddr memory controller
+ * @p:		Pointer to the ocm ecc status structure
+ * @mask:	Status register mask value
+ *
+ * Determines there is any ecc error or not
+ *
+ */
+static void zynqmp_ocm_edac_geterror_info(void __iomem *base,
+				    struct zynqmp_ocm_ecc_status *p, int mask)
+{
+	if (mask & OCM_CEINTR_MASK) {
+		p->ce_cnt++;
+		p->ceinfo.data0 = readl(base + CE_FFD0_OFST);
+		p->ceinfo.data1 = readl(base + CE_FFD1_OFST);
+		p->ceinfo.addr = (OCM_BASEVAL | readl(base + CE_FFA_OFST));
+		writel(ECC_CTRL_CLR_CE_ERR, base + OCM_ISR_OFST);
+	} else if (mask & OCM_UEINTR_MASK) {
+		p->ue_cnt++;
+		p->ueinfo.data0 = readl(base + UE_FFD0_OFST);
+		p->ueinfo.data1 = readl(base + UE_FFD1_OFST);
+		p->ueinfo.addr = (OCM_BASEVAL | readl(base + UE_FFA_OFST));
+		writel(ECC_CTRL_CLR_UE_ERR, base + OCM_ISR_OFST);
+	}
+}
+
+/**
+ * zynqmp_ocm_edac_handle_error - Handle controller error types CE and UE
+ * @dci:	Pointer to the edac device controller instance
+ * @p:		Pointer to the ocm ecc status structure
+ *
+ * Handles the controller ECC correctable and un correctable error.
+ */
+static void zynqmp_ocm_edac_handle_error(struct edac_device_ctl_info *dci,
+				    struct zynqmp_ocm_ecc_status *p)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+	struct ecc_error_info *pinf;
+
+	if (p->ce_cnt) {
+		pinf = &p->ceinfo;
+		snprintf(priv->message, ZYNQMP_OCM_EDAC_MSG_SIZE,
+			 "\n\rOCM ECC error type :%s\n\r"
+			 "Addr: [0x%X]\n\rFault Data[31:0]: [0x%X]\n\r"
+			 "Fault Data[63:32]: [0x%X]",
+			 "CE", pinf->addr, pinf->data0, pinf->data1);
+		edac_device_handle_ce(dci, 0, 0, priv->message);
+	}
+
+	if (p->ue_cnt) {
+		pinf = &p->ueinfo;
+		snprintf(priv->message, ZYNQMP_OCM_EDAC_MSG_SIZE,
+			 "\n\rOCM ECC error type :%s\n\r"
+			 "Addr: [0x%X]\n\rFault Data[31:0]: [0x%X]\n\r"
+			 "Fault Data[63:32]: [0x%X]",
+			 "UE", pinf->addr, pinf->data0, pinf->data1);
+		edac_device_handle_ue(dci, 0, 0, priv->message);
+	}
+
+	memset(p, 0, sizeof(*p));
+}
+
+/**
+ * zynqmp_ocm_edac_intr_handler - isr routine
+ * @irq:        irq number
+ * @dev_id:     device id poniter
+ *
+ * This is the Isr routine called by edac core interrupt thread.
+ * Used to check and post ECC errors.
+ *
+ * Return: IRQ_NONE, if interrupt not set or IRQ_HANDLED otherwise
+ */
+static irqreturn_t zynqmp_ocm_edac_intr_handler(int irq, void *dev_id)
+{
+	struct edac_device_ctl_info *dci = dev_id;
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+	int regval;
+
+	regval = readl(priv->baseaddr + OCM_ISR_OFST);
+	if (!(regval & OCM_CEUE_MASK))
+		return IRQ_NONE;
+
+	zynqmp_ocm_edac_geterror_info(priv->baseaddr,
+				&priv->stat, regval);
+
+	priv->ce_cnt += priv->stat.ce_cnt;
+	priv->ue_cnt += priv->stat.ue_cnt;
+	zynqmp_ocm_edac_handle_error(dci, &priv->stat);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * zynqmp_ocm_edac_get_eccstate - Return the controller ecc status
+ * @base:	Pointer to the ddr memory controller base address
+ *
+ * Get the ECC enable/disable status for the controller
+ *
+ * Return: ecc status 0/1.
+ */
+static bool zynqmp_ocm_edac_get_eccstate(void __iomem *base)
+{
+	return readl(base + ECC_CTRL_OFST) & OCM_ECC_ENABLE_MASK;
+}
+
+static const struct of_device_id zynqmp_ocm_edac_match[] = {
+	{ .compatible = "xlnx,zynqmp-ocmc-1.0"},
+	{ /* end of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, zynqmp_ocm_edac_match);
+
+/**
+ * zynqmp_ocm_edac_inject_fault_count_show - Shows fault injection count
+ * @dci:        Pointer to the edac device struct
+ * @data:       Pointer to user data
+ *
+ * Shows the fault injection count, once the counter reaches
+ * zero, it injects errors
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_fault_count_show(
+		struct edac_device_ctl_info *dci, char *data)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	return sprintf(data, "FIC: 0x%x\n\r",
+			readl(priv->baseaddr + OCM_FIC_OFST));
+}
+
+/**
+ * zynqmp_ocm_edac_inject_fault_count_store - write fi count
+ * @dci:	Pointer to the edac device struct
+ * @data:	Pointer to user data
+ * @count:	read the size bytes from buffer
+ *
+ * Update the fault injection count register, once the counter reaches
+ * zero, it injects errors
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_fault_count_store(
+		struct edac_device_ctl_info *dci, const char *data,
+		size_t count)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+	u32 ficount;
+
+	if (!data)
+		return -EFAULT;
+
+	if (kstrtouint(data, 0, &ficount))
+		return -EINVAL;
+
+	ficount &= OCM_FICOUNT_MASK;
+	writel(ficount, priv->baseaddr + OCM_FIC_OFST);
+
+	return count;
+}
+
+/**
+ * zynqmp_ocm_edac_inject_cebitpos_show - Shows CE bit position
+ * @dci:        Pointer to the edac device struct
+ * @data:       Pointer to user data
+ *
+ * Shows the Correctable error bit position,
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_cebitpos_show(struct edac_device_ctl_info
+							*dci, char *data)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	if (priv->ce_bitpos <= 31)
+		return sprintf(data, "Fault Injection Data Reg: [0x%x]\n\r",
+			((readl(priv->baseaddr + OCM_FID0_OFST))));
+
+	return sprintf(data, "Fault Injection Data Reg: [0x%x]\n\r",
+			((readl(priv->baseaddr + OCM_FID1_OFST))));
+}
+
+/**
+ * zynqmp_ocm_edac_inject_cebitpos_store - Set CE bit postion
+ * @dci:	Pointer to the edac device struct
+ * @data:	Pointer to user data
+ * @count:	read the size bytes from buffer
+ *
+ * Set any one bit to inject CE error
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_cebitpos_store(
+		struct edac_device_ctl_info *dci, const char *data,
+		size_t count)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	if (!data)
+		return -EFAULT;
+
+	if (kstrtou8(data, 0, &priv->ce_bitpos))
+		return -EINVAL;
+
+	if (priv->ce_bitpos <= 31) {
+		writel(1 << priv->ce_bitpos, priv->baseaddr + OCM_FID0_OFST);
+		writel(0, priv->baseaddr + OCM_FID1_OFST);
+	} else if (priv->ce_bitpos >= 32 && priv->ce_bitpos <= 63) {
+		writel(1 << (priv->ce_bitpos - 32),
+				priv->baseaddr + OCM_FID1_OFST);
+		writel(0, priv->baseaddr + OCM_FID0_OFST);
+	} else {
+		edac_printk(KERN_ERR, EDAC_DEVICE,
+			"Bit number > 64 is not valid\n");
+	}
+
+	return count;
+}
+
+/**
+ * zynqmp_ocm_edac_inject_uebitpos0_show - Shows UE bit postion0
+ * @dci:        Pointer to the edac device struct
+ * @data:       Pointer to user data
+ *
+ * Shows the one of bit position for UE error
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_uebitpos0_show(
+		struct edac_device_ctl_info *dci, char *data)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	if (priv->ue_bitpos0 <= 31)
+		return sprintf(data, "Fault Injection Data Reg: [0x%x]\n\r",
+			((readl(priv->baseaddr + OCM_FID0_OFST))));
+
+	return sprintf(data, "Fault Injection Data Reg: [0x%x]\n\r",
+			((readl(priv->baseaddr + OCM_FID1_OFST))));
+}
+
+/**
+ * zynqmp_ocm_edac_inject_uebitpos0_store - set UE bit position0
+ * @dci:	Pointer to the edac device struct
+ * @data:	Pointer to user data
+ * @count:	read the size bytes from buffer
+ *
+ * Set the first bit postion for UE Error generation,we need to configure
+ * any two bitpositions to inject UE Error
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_uebitpos0_store(
+		struct edac_device_ctl_info *dci,
+		const char *data, size_t count)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	if (!data)
+		return -EFAULT;
+
+	if (kstrtou8(data, 0, &priv->ue_bitpos0))
+		return -EINVAL;
+
+	if (priv->ue_bitpos0 <= 31)
+		writel(1 << priv->ue_bitpos0, priv->baseaddr + OCM_FID0_OFST);
+	else if (priv->ue_bitpos0 >= 32 && priv->ue_bitpos0 <= 63)
+		writel(1 << (priv->ue_bitpos0 - 32),
+				priv->baseaddr + OCM_FID1_OFST);
+	else
+		edac_printk(KERN_ERR, EDAC_DEVICE,
+			"Bit position > 64 is not valid\n");
+	edac_printk(KERN_INFO, EDAC_DEVICE,
+			"Set another bit position for UE\n");
+	return count;
+}
+
+/**
+ * zynqmp_ocm_edac_inject_uebitpos1_show - Shows UE bit postion1
+ * @dci:        Pointer to the edac device struct
+ * @data:       Pointer to user data
+ *
+ * Shows the second bit postion configured for UE error
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_uebitpos1_show(
+		struct edac_device_ctl_info *dci, char *data)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	if (priv->ue_bitpos1 <= 31)
+		return sprintf(data, "Fault Injection Data Reg: [0x%x]\n\r",
+			((readl(priv->baseaddr + OCM_FID0_OFST))));
+
+	return sprintf(data, "Fault Injection Data Reg: [0x%x]\n\r",
+			((readl(priv->baseaddr + OCM_FID1_OFST))));
+
+}
+
+/**
+ * zynqmp_ocm_edac_inject_uebitpos1_store - Set UE second bit postion
+ * @dci:	Pointer to the edac device struct
+ * @data:	Pointer to user data
+ * @count:	read the size bytes from buffer
+ *
+ * Set the second bit postion for UE Error generation,we need to configure
+ * any two bitpositions to inject UE Error
+ * Return: Number of bytes copied.
+ */
+static ssize_t zynqmp_ocm_edac_inject_uebitpos1_store(
+		struct edac_device_ctl_info *dci, const char *data,
+		size_t count)
+{
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+	u32 mask;
+
+	if (!data)
+		return -EFAULT;
+
+	if (kstrtou8(data, 0, &priv->ue_bitpos1))
+		return -EINVAL;
+
+	if (priv->ue_bitpos0 == priv->ue_bitpos1) {
+		edac_printk(KERN_ERR, EDAC_DEVICE,
+				"Bit positions should not be equal\n");
+		return -EINVAL;
+	}
+
+	/* If both bit postions are referring to 32 bit data, then configure
+	 * only FID0 register or if it is 64 bit data, then configure only
+	 * FID1 register.
+	 */
+	if (priv->ue_bitpos0 <= 31 &&
+	    priv->ue_bitpos1 <= 31) {
+		mask = (1 << priv->ue_bitpos0);
+		mask |= (1 << priv->ue_bitpos1);
+		writel(mask, priv->baseaddr + OCM_FID0_OFST);
+		writel(0, priv->baseaddr + OCM_FID1_OFST);
+	} else if ((priv->ue_bitpos0 >= 32 && priv->ue_bitpos0 <= 63) &&
+			(priv->ue_bitpos1 >= 32 && priv->ue_bitpos1 <= 63)) {
+		mask = (1 << (priv->ue_bitpos0 - 32));
+		mask |= (1 << (priv->ue_bitpos1 - 32));
+		writel(mask, priv->baseaddr + OCM_FID1_OFST);
+		writel(0, priv->baseaddr + OCM_FID0_OFST);
+	}
+
+	/* If one bit position is referring a bit in 32 bit data and other in
+	 * 64 bit data, just configure FID0/FID1 based on uebitpos1.
+	 */
+	if ((priv->ue_bitpos0 <= 31) &&
+	    (priv->ue_bitpos1 >= 32 && priv->ue_bitpos1 <= 63)) {
+		writel(1 << (priv->ue_bitpos1 - 32),
+				priv->baseaddr + OCM_FID1_OFST);
+	} else if ((priv->ue_bitpos0 >= 32 && priv->ue_bitpos0 <= 63) &&
+			(priv->ue_bitpos1 <= 31)) {
+		writel(1 << priv->ue_bitpos1,
+				priv->baseaddr + OCM_FID0_OFST);
+	} else {
+		edac_printk(KERN_ERR, EDAC_DEVICE,
+			"Bit position > 64 is not valid, Valid bits:[63:0]\n");
+	}
+
+	edac_printk(KERN_INFO, EDAC_DEVICE,
+			"UE at Bit Position0: %d Bit Position1: %d\n",
+			priv->ue_bitpos0, priv->ue_bitpos1);
+	return count;
+}
+
+static struct edac_dev_sysfs_attribute zynqmp_ocm_edac_sysfs_attributes[] = {
+	{
+		.attr = {
+			.name = "inject_cebitpos",
+			.mode = (0644)
+		},
+		.show = zynqmp_ocm_edac_inject_cebitpos_show,
+		.store = zynqmp_ocm_edac_inject_cebitpos_store},
+	{
+		.attr = {
+			.name = "inject_uebitpos0",
+			.mode = (0644)
+		},
+		.show = zynqmp_ocm_edac_inject_uebitpos0_show,
+		.store = zynqmp_ocm_edac_inject_uebitpos0_store},
+	{
+		.attr = {
+			.name = "inject_uebitpos1",
+			.mode = (0644)
+		},
+		.show = zynqmp_ocm_edac_inject_uebitpos1_show,
+		.store = zynqmp_ocm_edac_inject_uebitpos1_store},
+	{
+		.attr = {
+			.name = "inject_fault_count",
+			.mode = (0644)
+		},
+		.show = zynqmp_ocm_edac_inject_fault_count_show,
+		.store = zynqmp_ocm_edac_inject_fault_count_store},
+	/* End of list */
+	{
+		.attr = {.name = NULL}
+	}
+};
+
+/**
+ * zynqmp_set_ocm_edac_sysfs_attributes - create sysfs attributes
+ * @edac_dev:	Pointer to the edac device struct
+ *
+ * Creates sysfs entires for error injection
+ * Return: None.
+ */
+static void zynqmp_set_ocm_edac_sysfs_attributes(struct edac_device_ctl_info
+						*edac_dev)
+{
+	edac_dev->sysfs_attributes = zynqmp_ocm_edac_sysfs_attributes;
+}
+
+/**
+ * zynqmp_ocm_edac_probe - Check controller and bind driver
+ * @pdev:	Pointer to the platform_device struct
+ *
+ * Probes a specific controller instance for binding with the driver.
+ *
+ * Return: 0 if the controller instance was successfully bound to the
+ * driver; otherwise, < 0 on error.
+ */
+static int zynqmp_ocm_edac_probe(struct platform_device *pdev)
+{
+	struct edac_device_ctl_info *dci;
+	struct zynqmp_ocm_edac_priv *priv;
+	int irq, status;
+	struct resource *res;
+	void __iomem *baseaddr;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	baseaddr = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(baseaddr))
+		return PTR_ERR(baseaddr);
+
+	if (!zynqmp_ocm_edac_get_eccstate(baseaddr)) {
+		edac_printk(KERN_INFO, EDAC_DEVICE,
+				"ECC not enabled - Disabling EDAC driver\n");
+		return -ENXIO;
+	}
+
+	dci = edac_device_alloc_ctl_info(sizeof(*priv), ZYNQMP_OCM_EDAC_STRING,
+			1, ZYNQMP_OCM_EDAC_STRING, 1, 0, NULL, 0,
+			edac_device_alloc_index());
+	if (!dci) {
+		edac_printk(KERN_ERR, EDAC_DEVICE,
+				"Unable to allocate EDAC device\n");
+		return -ENOMEM;
+	}
+
+	priv = dci->pvt_info;
+	platform_set_drvdata(pdev, dci);
+	dci->dev = &pdev->dev;
+	priv->baseaddr = baseaddr;
+	dci->mod_name = pdev->dev.driver->name;
+	dci->ctl_name = ZYNQMP_OCM_EDAC_STRING;
+	dci->dev_name = dev_name(&pdev->dev);
+
+	zynqmp_set_ocm_edac_sysfs_attributes(dci);
+	if (edac_device_add_device(dci))
+		goto free_dev_ctl;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		edac_printk(KERN_ERR, EDAC_DEVICE,
+				"No irq %d in DT\n", irq);
+		return irq;
+	}
+
+	status = devm_request_irq(&pdev->dev, irq,
+		zynqmp_ocm_edac_intr_handler,
+		0, dev_name(&pdev->dev), dci);
+	if (status < 0) {
+		edac_printk(KERN_ERR, EDAC_DEVICE, "Failed to request Irq\n");
+		goto free_edac_dev;
+	}
+
+	writel(OCM_CEUE_MASK, priv->baseaddr + OCM_IEN_OFST);
+
+	return 0;
+
+free_edac_dev:
+	edac_device_del_device(&pdev->dev);
+free_dev_ctl:
+	edac_device_free_ctl_info(dci);
+
+	return -1;
+}
+
+/**
+ * zynqmp_ocm_edac_remove - Unbind driver from controller
+ * @pdev:	Pointer to the platform_device struct
+ *
+ * Return: Unconditionally 0
+ */
+static int zynqmp_ocm_edac_remove(struct platform_device *pdev)
+{
+	struct edac_device_ctl_info *dci = platform_get_drvdata(pdev);
+	struct zynqmp_ocm_edac_priv *priv = dci->pvt_info;
+
+	writel(OCM_CEUE_MASK, priv->baseaddr + OCM_IDS_OFST);
+	edac_device_del_device(&pdev->dev);
+	edac_device_free_ctl_info(dci);
+
+	return 0;
+}
+
+static struct platform_driver zynqmp_ocm_edac_driver = {
+	.driver = {
+		   .name = "zynqmp-ocm-edac",
+		   .of_match_table = zynqmp_ocm_edac_match,
+		   },
+	.probe = zynqmp_ocm_edac_probe,
+	.remove = zynqmp_ocm_edac_remove,
+};
+
+module_platform_driver(zynqmp_ocm_edac_driver);
+
+MODULE_AUTHOR("Xilinx Inc");
+MODULE_DESCRIPTION("ZynqMP OCM ECC driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/extcon/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/extcon/Kconfig
@@ -113,7 +113,8 @@
 
 config EXTCON_MAX8997
 	tristate "Maxim MAX8997 EXTCON Support"
-	depends on MFD_MAX8997 && IRQ_DOMAIN
+	depends on MFD_MAX8997
+	select IRQ_DOMAIN
 	help
 	  If you say yes here you get support for the MUIC device of
 	  Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory
@@ -180,7 +181,7 @@
 
 config EXTCON_USBC_TUSB320
 	tristate "TI TUSB320 USB-C extcon support"
-	depends on I2C
+	depends on I2C && TYPEC
 	select REGMAP_I2C
 	help
 	  Say Y here to enable support for USB Type C cable detection extcon
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/extcon/extcon-axp288.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/extcon/extcon-axp288.c
@@ -375,8 +375,8 @@
 		if (adev) {
 			info->id_extcon = extcon_get_extcon_dev(acpi_dev_name(adev));
 			put_device(&adev->dev);
-			if (!info->id_extcon)
-				return -EPROBE_DEFER;
+			if (IS_ERR(info->id_extcon))
+				return PTR_ERR(info->id_extcon);
 
 			dev_info(dev, "controlling USB role\n");
 		} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/extcon/extcon-ptn5150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/extcon/extcon-ptn5150.c
@@ -194,6 +194,13 @@
 	return 0;
 }
 
+static void ptn5150_work_sync_and_put(void *data)
+{
+	struct ptn5150_info *info = data;
+
+	cancel_work_sync(&info->irq_work);
+}
+
 static int ptn5150_i2c_probe(struct i2c_client *i2c)
 {
 	struct device *dev = &i2c->dev;
@@ -284,6 +291,10 @@
 	if (ret)
 		return -EINVAL;
 
+	ret = devm_add_action_or_reset(dev, ptn5150_work_sync_and_put, info);
+	if (ret)
+		return ret;
+
 	/*
 	 * Update current extcon state if for example OTG connection was there
 	 * before the probe
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/extcon/extcon-usbc-tusb320.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/extcon/extcon-usbc-tusb320.c
@@ -1,11 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0
-/**
+/*
  * drivers/extcon/extcon-tusb320.c - TUSB320 extcon driver
  *
  * Copyright (C) 2020 National Instruments Corporation
  * Author: Michael Auchter <michael.auchter@ni.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/extcon-provider.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
@@ -13,21 +14,70 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/regmap.h>
+#include <linux/usb/typec.h>
+
+#define TUSB320_REG8				0x8
+#define TUSB320_REG8_CURRENT_MODE_ADVERTISE	GENMASK(7, 6)
+#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB	0x0
+#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A	0x1
+#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A	0x2
+#define TUSB320_REG8_CURRENT_MODE_DETECT	GENMASK(5, 4)
+#define TUSB320_REG8_CURRENT_MODE_DETECT_DEF	0x0
+#define TUSB320_REG8_CURRENT_MODE_DETECT_MED	0x1
+#define TUSB320_REG8_CURRENT_MODE_DETECT_ACC	0x2
+#define TUSB320_REG8_CURRENT_MODE_DETECT_HI	0x3
+#define TUSB320_REG8_ACCESSORY_CONNECTED	GENMASK(3, 2)
+#define TUSB320_REG8_ACCESSORY_CONNECTED_NONE	0x0
+#define TUSB320_REG8_ACCESSORY_CONNECTED_AUDIO	0x4
+#define TUSB320_REG8_ACCESSORY_CONNECTED_ACC	0x5
+#define TUSB320_REG8_ACCESSORY_CONNECTED_DEBUG	0x6
+#define TUSB320_REG8_ACTIVE_CABLE_DETECTION	BIT(0)
 
 #define TUSB320_REG9				0x9
 #define TUSB320_REG9_ATTACHED_STATE_SHIFT	6
 #define TUSB320_REG9_ATTACHED_STATE_MASK	0x3
 #define TUSB320_REG9_CABLE_DIRECTION		BIT(5)
 #define TUSB320_REG9_INTERRUPT_STATUS		BIT(4)
-#define TUSB320_ATTACHED_STATE_NONE		0x0
-#define TUSB320_ATTACHED_STATE_DFP		0x1
-#define TUSB320_ATTACHED_STATE_UFP		0x2
-#define TUSB320_ATTACHED_STATE_ACC		0x3
+
+#define TUSB320_REGA				0xa
+#define TUSB320L_REGA_DISABLE_TERM		BIT(0)
+#define TUSB320_REGA_I2C_SOFT_RESET		BIT(3)
+#define TUSB320_REGA_MODE_SELECT_SHIFT		4
+#define TUSB320_REGA_MODE_SELECT_MASK		0x3
+
+#define TUSB320L_REGA0_REVISION			0xa0
+
+enum tusb320_attached_state {
+	TUSB320_ATTACHED_STATE_NONE,
+	TUSB320_ATTACHED_STATE_DFP,
+	TUSB320_ATTACHED_STATE_UFP,
+	TUSB320_ATTACHED_STATE_ACC,
+};
+
+enum tusb320_mode {
+	TUSB320_MODE_PORT,
+	TUSB320_MODE_UFP,
+	TUSB320_MODE_DFP,
+	TUSB320_MODE_DRP,
+};
+
+struct tusb320_priv;
+
+struct tusb320_ops {
+	int (*set_mode)(struct tusb320_priv *priv, enum tusb320_mode mode);
+	int (*get_revision)(struct tusb320_priv *priv, unsigned int *revision);
+};
 
 struct tusb320_priv {
 	struct device *dev;
 	struct regmap *regmap;
 	struct extcon_dev *edev;
+	struct tusb320_ops *ops;
+	enum tusb320_attached_state state;
+	struct typec_port *port;
+	struct typec_capability	cap;
+	enum typec_port_type port_type;
+	enum typec_pwr_opmode pwr_opmode;
 };
 
 static const char * const tusb_attached_states[] = {
@@ -62,19 +112,142 @@
 	return 0;
 }
 
-static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)
+static int tusb320_set_mode(struct tusb320_priv *priv, enum tusb320_mode mode)
 {
-	struct tusb320_priv *priv = dev_id;
-	int state, polarity;
-	unsigned reg;
+	int ret;
 
-	if (regmap_read(priv->regmap, TUSB320_REG9, &reg)) {
-		dev_err(priv->dev, "error during i2c read!\n");
-		return IRQ_NONE;
+	/* Mode cannot be changed while cable is attached */
+	if (priv->state != TUSB320_ATTACHED_STATE_NONE)
+		return -EBUSY;
+
+	/* Write mode */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+		TUSB320_REGA_MODE_SELECT_MASK << TUSB320_REGA_MODE_SELECT_SHIFT,
+		mode << TUSB320_REGA_MODE_SELECT_SHIFT);
+	if (ret) {
+		dev_err(priv->dev, "failed to write mode: %d\n", ret);
+		return ret;
 	}
 
-	if (!(reg & TUSB320_REG9_INTERRUPT_STATUS))
-		return IRQ_NONE;
+	return 0;
+}
+
+static int tusb320l_set_mode(struct tusb320_priv *priv, enum tusb320_mode mode)
+{
+	int ret;
+
+	/* Disable CC state machine */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+		TUSB320L_REGA_DISABLE_TERM, 1);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to disable CC state machine: %d\n", ret);
+		return ret;
+	}
+
+	/* Write mode */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+		TUSB320_REGA_MODE_SELECT_MASK << TUSB320_REGA_MODE_SELECT_SHIFT,
+		mode << TUSB320_REGA_MODE_SELECT_SHIFT);
+	if (ret) {
+		dev_err(priv->dev, "failed to write mode: %d\n", ret);
+		goto err;
+	}
+
+	msleep(5);
+err:
+	/* Re-enable CC state machine */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+		TUSB320L_REGA_DISABLE_TERM, 0);
+	if (ret)
+		dev_err(priv->dev,
+			"failed to re-enable CC state machine: %d\n", ret);
+
+	return ret;
+}
+
+static int tusb320_reset(struct tusb320_priv *priv)
+{
+	int ret;
+
+	/* Set mode to default (follow PORT pin) */
+	ret = priv->ops->set_mode(priv, TUSB320_MODE_PORT);
+	if (ret && ret != -EBUSY) {
+		dev_err(priv->dev,
+			"failed to set mode to PORT: %d\n", ret);
+		return ret;
+	}
+
+	/* Perform soft reset */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+			TUSB320_REGA_I2C_SOFT_RESET, 1);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to write soft reset bit: %d\n", ret);
+		return ret;
+	}
+
+	/* Wait for chip to go through reset */
+	msleep(95);
+
+	return 0;
+}
+
+static int tusb320l_get_revision(struct tusb320_priv *priv, unsigned int *revision)
+{
+	return regmap_read(priv->regmap, TUSB320L_REGA0_REVISION, revision);
+}
+
+static struct tusb320_ops tusb320_ops = {
+	.set_mode = tusb320_set_mode,
+};
+
+static struct tusb320_ops tusb320l_ops = {
+	.set_mode = tusb320l_set_mode,
+	.get_revision = tusb320l_get_revision,
+};
+
+static int tusb320_set_adv_pwr_mode(struct tusb320_priv *priv)
+{
+	u8 mode;
+
+	if (priv->pwr_opmode == TYPEC_PWR_MODE_USB)
+		mode = TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB;
+	else if (priv->pwr_opmode == TYPEC_PWR_MODE_1_5A)
+		mode = TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A;
+	else if (priv->pwr_opmode == TYPEC_PWR_MODE_3_0A)
+		mode = TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A;
+	else	/* No other mode is supported. */
+		return -EINVAL;
+
+	return regmap_write_bits(priv->regmap, TUSB320_REG8,
+				 TUSB320_REG8_CURRENT_MODE_ADVERTISE,
+				 FIELD_PREP(TUSB320_REG8_CURRENT_MODE_ADVERTISE,
+					    mode));
+}
+
+static int tusb320_port_type_set(struct typec_port *port,
+				 enum typec_port_type type)
+{
+	struct tusb320_priv *priv = typec_get_drvdata(port);
+
+	if (type == TYPEC_PORT_SRC)
+		return priv->ops->set_mode(priv, TUSB320_MODE_DFP);
+	else if (type == TYPEC_PORT_SNK)
+		return priv->ops->set_mode(priv, TUSB320_MODE_UFP);
+	else if (type == TYPEC_PORT_DRP)
+		return priv->ops->set_mode(priv, TUSB320_MODE_DRP);
+	else
+		return priv->ops->set_mode(priv, TUSB320_MODE_PORT);
+}
+
+static const struct typec_operations tusb320_typec_ops = {
+	.port_type_set	= tusb320_port_type_set,
+};
+
+static void tusb320_extcon_irq_handler(struct tusb320_priv *priv, u8 reg)
+{
+	int state, polarity;
 
 	state = (reg >> TUSB320_REG9_ATTACHED_STATE_SHIFT) &
 		TUSB320_REG9_ATTACHED_STATE_MASK;
@@ -96,20 +269,170 @@
 	extcon_sync(priv->edev, EXTCON_USB);
 	extcon_sync(priv->edev, EXTCON_USB_HOST);
 
+	priv->state = state;
+}
+
+static void tusb320_typec_irq_handler(struct tusb320_priv *priv, u8 reg9)
+{
+	struct typec_port *port = priv->port;
+	struct device *dev = priv->dev;
+	u8 mode, role, state;
+	int ret, reg8;
+	bool ori;
+
+	ori = reg9 & TUSB320_REG9_CABLE_DIRECTION;
+	typec_set_orientation(port, ori ? TYPEC_ORIENTATION_REVERSE :
+					  TYPEC_ORIENTATION_NORMAL);
+
+	state = (reg9 >> TUSB320_REG9_ATTACHED_STATE_SHIFT) &
+		TUSB320_REG9_ATTACHED_STATE_MASK;
+	if (state == TUSB320_ATTACHED_STATE_DFP)
+		role = TYPEC_SOURCE;
+	else
+		role = TYPEC_SINK;
+
+	typec_set_vconn_role(port, role);
+	typec_set_pwr_role(port, role);
+	typec_set_data_role(port, role == TYPEC_SOURCE ?
+				  TYPEC_HOST : TYPEC_DEVICE);
+
+	ret = regmap_read(priv->regmap, TUSB320_REG8, &reg8);
+	if (ret) {
+		dev_err(dev, "error during reg8 i2c read, ret=%d!\n", ret);
+		return;
+	}
+
+	mode = FIELD_GET(TUSB320_REG8_CURRENT_MODE_DETECT, reg8);
+	if (mode == TUSB320_REG8_CURRENT_MODE_DETECT_DEF)
+		typec_set_pwr_opmode(port, TYPEC_PWR_MODE_USB);
+	else if (mode == TUSB320_REG8_CURRENT_MODE_DETECT_MED)
+		typec_set_pwr_opmode(port, TYPEC_PWR_MODE_1_5A);
+	else if (mode == TUSB320_REG8_CURRENT_MODE_DETECT_HI)
+		typec_set_pwr_opmode(port, TYPEC_PWR_MODE_3_0A);
+	else	/* Charge through accessory */
+		typec_set_pwr_opmode(port, TYPEC_PWR_MODE_USB);
+}
+
+static irqreturn_t tusb320_state_update_handler(struct tusb320_priv *priv,
+						bool force_update)
+{
+	unsigned int reg;
+
+	if (regmap_read(priv->regmap, TUSB320_REG9, &reg)) {
+		dev_err(priv->dev, "error during i2c read!\n");
+		return IRQ_NONE;
+	}
+
+	if (!force_update && !(reg & TUSB320_REG9_INTERRUPT_STATUS))
+		return IRQ_NONE;
+
+	tusb320_extcon_irq_handler(priv, reg);
+
+	/*
+	 * Type-C support is optional. Only call the Type-C handler if a
+	 * port had been registered previously.
+	 */
+	if (priv->port)
+		tusb320_typec_irq_handler(priv, reg);
+
 	regmap_write(priv->regmap, TUSB320_REG9, reg);
 
 	return IRQ_HANDLED;
 }
 
+static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)
+{
+	struct tusb320_priv *priv = dev_id;
+
+	return tusb320_state_update_handler(priv, false);
+}
+
 static const struct regmap_config tusb320_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
 };
 
-static int tusb320_extcon_probe(struct i2c_client *client,
-				const struct i2c_device_id *id)
+static int tusb320_extcon_probe(struct tusb320_priv *priv)
+{
+	int ret;
+
+	priv->edev = devm_extcon_dev_allocate(priv->dev, tusb320_extcon_cable);
+	if (IS_ERR(priv->edev)) {
+		dev_err(priv->dev, "failed to allocate extcon device\n");
+		return PTR_ERR(priv->edev);
+	}
+
+	ret = devm_extcon_dev_register(priv->dev, priv->edev);
+	if (ret < 0) {
+		dev_err(priv->dev, "failed to register extcon device\n");
+		return ret;
+	}
+
+	extcon_set_property_capability(priv->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_TYPEC_POLARITY);
+	extcon_set_property_capability(priv->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_TYPEC_POLARITY);
+
+	return 0;
+}
+
+static int tusb320_typec_probe(struct i2c_client *client,
+			       struct tusb320_priv *priv)
+{
+	struct fwnode_handle *connector;
+	const char *cap_str;
+	int ret;
+
+	/* The Type-C connector is optional, for backward compatibility. */
+	connector = device_get_named_child_node(&client->dev, "connector");
+	if (!connector)
+		return 0;
+
+	/* Type-C connector found. */
+	ret = typec_get_fw_cap(&priv->cap, connector);
+	if (ret)
+		return ret;
+
+	priv->port_type = priv->cap.type;
+
+	/* This goes into register 0x8 field CURRENT_MODE_ADVERTISE */
+	ret = fwnode_property_read_string(connector, "typec-power-opmode", &cap_str);
+	if (ret)
+		return ret;
+
+	ret = typec_find_pwr_opmode(cap_str);
+	if (ret < 0)
+		return ret;
+	if (ret == TYPEC_PWR_MODE_PD)
+		return -EINVAL;
+
+	priv->pwr_opmode = ret;
+
+	/* Initialize the hardware with the devicetree settings. */
+	ret = tusb320_set_adv_pwr_mode(priv);
+	if (ret)
+		return ret;
+
+	priv->cap.revision		= USB_TYPEC_REV_1_1;
+	priv->cap.accessory[0]		= TYPEC_ACCESSORY_AUDIO;
+	priv->cap.accessory[1]		= TYPEC_ACCESSORY_DEBUG;
+	priv->cap.orientation_aware	= true;
+	priv->cap.driver_data		= priv;
+	priv->cap.ops			= &tusb320_typec_ops;
+	priv->cap.fwnode		= connector;
+
+	priv->port = typec_register_port(&client->dev, &priv->cap);
+	if (IS_ERR(priv->port))
+		return PTR_ERR(priv->port);
+
+	return 0;
+}
+
+static int tusb320_probe(struct i2c_client *client)
 {
 	struct tusb320_priv *priv;
+	const void *match_data;
+	unsigned int revision;
 	int ret;
 
 	priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL);
@@ -125,25 +448,42 @@
 	if (ret)
 		return ret;
 
-	priv->edev = devm_extcon_dev_allocate(priv->dev, tusb320_extcon_cable);
-	if (IS_ERR(priv->edev)) {
-		dev_err(priv->dev, "failed to allocate extcon device\n");
-		return PTR_ERR(priv->edev);
+	match_data = device_get_match_data(&client->dev);
+	if (!match_data)
+		return -EINVAL;
+
+	priv->ops = (struct tusb320_ops*)match_data;
+
+	if (priv->ops->get_revision) {
+		ret = priv->ops->get_revision(priv, &revision);
+		if (ret)
+			dev_warn(priv->dev,
+				"failed to read revision register: %d\n", ret);
+		else
+			dev_info(priv->dev, "chip revision %d\n", revision);
 	}
 
-	ret = devm_extcon_dev_register(priv->dev, priv->edev);
-	if (ret < 0) {
-		dev_err(priv->dev, "failed to register extcon device\n");
+	ret = tusb320_extcon_probe(priv);
+	if (ret)
 		return ret;
-	}
 
-	extcon_set_property_capability(priv->edev, EXTCON_USB,
-				       EXTCON_PROP_USB_TYPEC_POLARITY);
-	extcon_set_property_capability(priv->edev, EXTCON_USB_HOST,
-				       EXTCON_PROP_USB_TYPEC_POLARITY);
+	ret = tusb320_typec_probe(client, priv);
+	if (ret)
+		return ret;
 
 	/* update initial state */
-	tusb320_irq_handler(client->irq, priv);
+	tusb320_state_update_handler(priv, true);
+
+	/* Reset chip to its default state */
+	ret = tusb320_reset(priv);
+	if (ret)
+		dev_warn(priv->dev, "failed to reset chip: %d\n", ret);
+	else
+		/*
+		 * State and polarity might change after a reset, so update
+		 * them again and make sure the interrupt status bit is cleared.
+		 */
+		tusb320_state_update_handler(priv, true);
 
 	ret = devm_request_threaded_irq(priv->dev, client->irq, NULL,
 					tusb320_irq_handler,
@@ -154,13 +494,14 @@
 }
 
 static const struct of_device_id tusb320_extcon_dt_match[] = {
-	{ .compatible = "ti,tusb320", },
+	{ .compatible = "ti,tusb320", .data = &tusb320_ops, },
+	{ .compatible = "ti,tusb320l", .data = &tusb320l_ops, },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, tusb320_extcon_dt_match);
 
 static struct i2c_driver tusb320_extcon_driver = {
-	.probe		= tusb320_extcon_probe,
+	.probe_new	= tusb320_probe,
 	.driver		= {
 		.name	= "extcon-tusb320",
 		.of_match_table = tusb320_extcon_dt_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/extcon/extcon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/extcon/extcon.c
@@ -196,6 +196,14 @@
  * @attr_name:		"name" sysfs entry
  * @attr_state:		"state" sysfs entry
  * @attrs:		the array pointing to attr_name and attr_state for attr_g
+ * @usb_propval:	the array of USB connector properties
+ * @chg_propval:	the array of charger connector properties
+ * @jack_propval:	the array of jack connector properties
+ * @disp_propval:	the array of display connector properties
+ * @usb_bits:		the bit array of the USB connector property capabilities
+ * @chg_bits:		the bit array of the charger connector property capabilities
+ * @jack_bits:		the bit array of the jack connector property capabilities
+ * @disp_bits:		the bit array of the display connector property capabilities
  */
 struct extcon_cable {
 	struct extcon_dev *edev;
@@ -863,6 +871,8 @@
  * @extcon_name:	the extcon name provided with extcon_dev_register()
  *
  * Return the pointer of extcon device if success or ERR_PTR(err) if fail.
+ * NOTE: This function returns -EPROBE_DEFER so it may only be called from
+ * probe() functions.
  */
 struct extcon_dev *extcon_get_extcon_dev(const char *extcon_name)
 {
@@ -876,7 +886,7 @@
 		if (!strcmp(sd->name, extcon_name))
 			goto out;
 	}
-	sd = NULL;
+	sd = ERR_PTR(-EPROBE_DEFER);
 out:
 	mutex_unlock(&extcon_dev_list_lock);
 	return sd;
@@ -1230,19 +1240,14 @@
 		edev->dev.type = &edev->extcon_dev_type;
 	}
 
-	ret = device_register(&edev->dev);
-	if (ret) {
-		put_device(&edev->dev);
-		goto err_dev;
-	}
-
 	spin_lock_init(&edev->lock);
-	edev->nh = devm_kcalloc(&edev->dev, edev->max_supported,
-				sizeof(*edev->nh), GFP_KERNEL);
-	if (!edev->nh) {
-		ret = -ENOMEM;
-		device_unregister(&edev->dev);
-		goto err_dev;
+	if (edev->max_supported) {
+		edev->nh = kcalloc(edev->max_supported, sizeof(*edev->nh),
+				GFP_KERNEL);
+		if (!edev->nh) {
+			ret = -ENOMEM;
+			goto err_alloc_nh;
+		}
 	}
 
 	for (index = 0; index < edev->max_supported; index++)
@@ -1253,6 +1258,12 @@
 	dev_set_drvdata(&edev->dev, edev);
 	edev->state = 0;
 
+	ret = device_register(&edev->dev);
+	if (ret) {
+		put_device(&edev->dev);
+		goto err_dev;
+	}
+
 	mutex_lock(&extcon_dev_list_lock);
 	list_add(&edev->entry, &extcon_dev_list);
 	mutex_unlock(&extcon_dev_list_lock);
@@ -1261,6 +1272,9 @@
 
 err_dev:
 	if (edev->max_supported)
+		kfree(edev->nh);
+err_alloc_nh:
+	if (edev->max_supported)
 		kfree(edev->extcon_dev_type.groups);
 err_alloc_groups:
 	if (edev->max_supported && edev->mutually_exclusive) {
@@ -1320,6 +1334,7 @@
 	if (edev->max_supported) {
 		kfree(edev->extcon_dev_type.groups);
 		kfree(edev->cables);
+		kfree(edev->nh);
 	}
 
 	put_device(&edev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/core-card.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/core-card.c
@@ -429,7 +429,23 @@
 	 */
 	card->bm_generation = generation;
 
-	if (root_device == NULL) {
+	if (card->gap_count == 0) {
+		/*
+		 * If self IDs have inconsistent gap counts, do a
+		 * bus reset ASAP. The config rom read might never
+		 * complete, so don't wait for it. However, still
+		 * send a PHY configuration packet prior to the
+		 * bus reset. The PHY configuration packet might
+		 * fail, but 1394-2008 8.4.5.2 explicitly permits
+		 * it in this case, so it should be safe to try.
+		 */
+		new_root_id = local_id;
+		/*
+		 * We must always send a bus reset if the gap count
+		 * is inconsistent, so bypass the 5-reset limit.
+		 */
+		card->bm_retries = 0;
+	} else if (root_device == NULL) {
 		/*
 		 * Either link_on is false, or we failed to read the
 		 * config rom.  In either case, pick another root.
@@ -484,7 +500,19 @@
 		fw_notice(card, "phy config: new root=%x, gap_count=%d\n",
 			  new_root_id, gap_count);
 		fw_send_phy_config(card, new_root_id, generation, gap_count);
-		reset_bus(card, true);
+		/*
+		 * Where possible, use a short bus reset to minimize
+		 * disruption to isochronous transfers. But in the event
+		 * of a gap count inconsistency, use a long bus reset.
+		 *
+		 * As noted in 1394a 8.4.6.2, nodes on a mixed 1394/1394a bus
+		 * may set different gap counts after a bus reset. On a mixed
+		 * 1394/1394a bus, a short bus reset can get doubled. Some
+		 * nodes may treat the double reset as one bus reset and others
+		 * may treat it as two, causing a gap count inconsistency
+		 * again. Using a long bus reset prevents this.
+		 */
+		reset_bus(card, card->gap_count != 0);
 		/* Will allocate broadcast channel after the reset. */
 		goto out;
 	}
@@ -668,6 +696,7 @@
 void fw_core_remove_card(struct fw_card *card)
 {
 	struct fw_card_driver dummy_driver = dummy_driver_template;
+	unsigned long flags;
 
 	card->driver->update_phy_reg(card, 4,
 				     PHY_LINK_ACTIVE | PHY_CONTENDER, 0);
@@ -682,7 +711,9 @@
 	dummy_driver.stop_iso		= card->driver->stop_iso;
 	card->driver = &dummy_driver;
 
+	spin_lock_irqsave(&card->lock, flags);
 	fw_destroy_nodes(card);
+	spin_unlock_irqrestore(&card->lock, flags);
 
 	/* Wait for all users, especially device workqueue jobs, to finish. */
 	fw_card_put(card);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/core-cdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/core-cdev.c
@@ -818,8 +818,10 @@
 
 	r = container_of(resource, struct inbound_transaction_resource,
 			 resource);
-	if (is_fcp_request(r->request))
+	if (is_fcp_request(r->request)) {
+		kfree(r->data);
 		goto out;
+	}
 
 	if (a->length != fw_get_response_length(r->request)) {
 		ret = -EINVAL;
@@ -1480,6 +1482,7 @@
 {
 	struct outbound_phy_packet_event *e =
 		container_of(packet, struct outbound_phy_packet_event, p);
+	struct client *e_client;
 
 	switch (status) {
 	/* expected: */
@@ -1496,9 +1499,10 @@
 	}
 	e->phy_packet.data[0] = packet->timestamp;
 
+	e_client = e->client;
 	queue_event(e->client, &e->event, &e->phy_packet,
 		    sizeof(e->phy_packet) + e->phy_packet.length, NULL, 0);
-	client_put(e->client);
+	client_put(e_client);
 }
 
 static int ioctl_send_phy_packet(struct client *client, union ioctl_arg *arg)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/core-device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/core-device.c
@@ -100,10 +100,9 @@
  * @buf:	where to put the string
  * @size:	size of @buf, in bytes
  *
- * The string is taken from a minimal ASCII text descriptor leaf after
- * the immediate entry with @key.  The string is zero-terminated.
- * An overlong string is silently truncated such that it and the
- * zero byte fit into @size.
+ * The string is taken from a minimal ASCII text descriptor leaf just after the entry with the
+ * @key. The string is zero-terminated. An overlong string is silently truncated such that it
+ * and the zero byte fit into @size.
  *
  * Returns strlen(buf) or a negative error code.
  */
@@ -719,14 +718,11 @@
 					fw_unit_attributes,
 					&unit->attribute_group);
 
-		if (device_register(&unit->device) < 0)
-			goto skip_unit;
-
 		fw_device_get(device);
-		continue;
-
-	skip_unit:
-		kfree(unit);
+		if (device_register(&unit->device) < 0) {
+			put_device(&unit->device);
+			continue;
+		}
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/core-topology.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/core-topology.c
@@ -375,16 +375,13 @@
 	card->bm_retries = 0;
 }
 
+/* Must be called with card->lock held */
 void fw_destroy_nodes(struct fw_card *card)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&card->lock, flags);
 	card->color++;
 	if (card->local_node != NULL)
 		for_each_fw_node(card, card->local_node, report_lost_node);
 	card->local_node = NULL;
-	spin_unlock_irqrestore(&card->lock, flags);
 }
 
 static void move_tree(struct fw_node *node0, struct fw_node *node1, int port)
@@ -510,6 +507,8 @@
 	struct fw_node *local_node;
 	unsigned long flags;
 
+	spin_lock_irqsave(&card->lock, flags);
+
 	/*
 	 * If the selfID buffer is not the immediate successor of the
 	 * previously processed one, we cannot reliably compare the
@@ -521,8 +520,6 @@
 		card->bm_retries = 0;
 	}
 
-	spin_lock_irqsave(&card->lock, flags);
-
 	card->broadcast_channel_allocated = card->broadcast_channel_auto_allocated;
 	card->node_id = node_id;
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/core-transaction.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/core-transaction.c
@@ -73,24 +73,25 @@
 static int close_transaction(struct fw_transaction *transaction,
 			     struct fw_card *card, int rcode)
 {
-	struct fw_transaction *t;
+	struct fw_transaction *t = NULL, *iter;
 	unsigned long flags;
 
 	spin_lock_irqsave(&card->lock, flags);
-	list_for_each_entry(t, &card->transaction_list, link) {
-		if (t == transaction) {
-			if (!try_cancel_split_timeout(t)) {
+	list_for_each_entry(iter, &card->transaction_list, link) {
+		if (iter == transaction) {
+			if (!try_cancel_split_timeout(iter)) {
 				spin_unlock_irqrestore(&card->lock, flags);
 				goto timed_out;
 			}
-			list_del_init(&t->link);
-			card->tlabel_mask &= ~(1ULL << t->tlabel);
+			list_del_init(&iter->link);
+			card->tlabel_mask &= ~(1ULL << iter->tlabel);
+			t = iter;
 			break;
 		}
 	}
 	spin_unlock_irqrestore(&card->lock, flags);
 
-	if (&t->link != &card->transaction_list) {
+	if (t) {
 		t->callback(card, rcode, NULL, 0, t->callback_data);
 		return 0;
 	}
@@ -935,7 +936,7 @@
 
 void fw_core_handle_response(struct fw_card *card, struct fw_packet *p)
 {
-	struct fw_transaction *t;
+	struct fw_transaction *t = NULL, *iter;
 	unsigned long flags;
 	u32 *data;
 	size_t data_length;
@@ -947,20 +948,21 @@
 	rcode	= HEADER_GET_RCODE(p->header[1]);
 
 	spin_lock_irqsave(&card->lock, flags);
-	list_for_each_entry(t, &card->transaction_list, link) {
-		if (t->node_id == source && t->tlabel == tlabel) {
-			if (!try_cancel_split_timeout(t)) {
+	list_for_each_entry(iter, &card->transaction_list, link) {
+		if (iter->node_id == source && iter->tlabel == tlabel) {
+			if (!try_cancel_split_timeout(iter)) {
 				spin_unlock_irqrestore(&card->lock, flags);
 				goto timed_out;
 			}
-			list_del_init(&t->link);
-			card->tlabel_mask &= ~(1ULL << t->tlabel);
+			list_del_init(&iter->link);
+			card->tlabel_mask &= ~(1ULL << iter->tlabel);
+			t = iter;
 			break;
 		}
 	}
 	spin_unlock_irqrestore(&card->lock, flags);
 
-	if (&t->link == &card->transaction_list) {
+	if (!t) {
  timed_out:
 		fw_notice(card, "unsolicited response (source %x, tlabel %x)\n",
 			  source, tlabel);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/net.c
@@ -488,7 +488,7 @@
 					struct sk_buff *skb, u16 source_node_id,
 					bool is_broadcast, u16 ether_type)
 {
-	int status;
+	int status, len;
 
 	switch (ether_type) {
 	case ETH_P_ARP:
@@ -542,13 +542,15 @@
 		}
 		skb->protocol = protocol;
 	}
+
+	len = skb->len;
 	status = netif_rx(skb);
 	if (status == NET_RX_DROP) {
 		net->stats.rx_errors++;
 		net->stats.rx_dropped++;
 	} else {
 		net->stats.rx_packets++;
-		net->stats.rx_bytes += skb->len;
+		net->stats.rx_bytes += len;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/nosy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/nosy.c
@@ -148,10 +148,12 @@
 	if (atomic_read(&buffer->size) == 0)
 		return -ENODEV;
 
-	/* FIXME: Check length <= user_length. */
+	length = buffer->head->length;
+
+	if (length > user_length)
+		return 0;
 
 	end = buffer->data + buffer->capacity;
-	length = buffer->head->length;
 
 	if (&buffer->head->data[length] < end) {
 		if (copy_to_user(data, buffer->head->data, length))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/ohci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/ohci.c
@@ -279,6 +279,51 @@
 #define QUIRK_TI_SLLZ059		0x20
 #define QUIRK_IR_WAKE			0x40
 
+// On PCI Express Root Complex in any type of AMD Ryzen machine, VIA VT6306/6307/6308 with Asmedia
+// ASM1083/1085 brings an inconvenience that the read accesses to 'Isochronous Cycle Timer' register
+// (at offset 0xf0 in PCI I/O space) often causes unexpected system reboot. The mechanism is not
+// clear, since the read access to the other registers is enough safe; e.g. 'Node ID' register,
+// while it is probable due to detection of any type of PCIe error.
+#define QUIRK_REBOOT_BY_CYCLE_TIMER_READ	0x80000000
+
+#if IS_ENABLED(CONFIG_X86)
+
+static bool has_reboot_by_cycle_timer_read_quirk(const struct fw_ohci *ohci)
+{
+	return !!(ohci->quirks & QUIRK_REBOOT_BY_CYCLE_TIMER_READ);
+}
+
+#define PCI_DEVICE_ID_ASMEDIA_ASM108X	0x1080
+
+static bool detect_vt630x_with_asm1083_on_amd_ryzen_machine(const struct pci_dev *pdev)
+{
+	const struct pci_dev *pcie_to_pci_bridge;
+
+	// Detect any type of AMD Ryzen machine.
+	if (!static_cpu_has(X86_FEATURE_ZEN))
+		return false;
+
+	// Detect VIA VT6306/6307/6308.
+	if (pdev->vendor != PCI_VENDOR_ID_VIA)
+		return false;
+	if (pdev->device != PCI_DEVICE_ID_VIA_VT630X)
+		return false;
+
+	// Detect Asmedia ASM1083/1085.
+	pcie_to_pci_bridge = pdev->bus->self;
+	if (pcie_to_pci_bridge->vendor != PCI_VENDOR_ID_ASMEDIA)
+		return false;
+	if (pcie_to_pci_bridge->device != PCI_DEVICE_ID_ASMEDIA_ASM108X)
+		return false;
+
+	return true;
+}
+
+#else
+#define has_reboot_by_cycle_timer_read_quirk(ohci) false
+#define detect_vt630x_with_asm1083_on_amd_ryzen_machine(pdev)	false
+#endif
+
 /* In case of multiple matches in ohci_quirks[], only the first one is used. */
 static const struct {
 	unsigned short vendor, device, revision, flags;
@@ -1713,6 +1758,9 @@
 	s32 diff01, diff12;
 	int i;
 
+	if (has_reboot_by_cycle_timer_read_quirk(ohci))
+		return 0;
+
 	c2 = reg_read(ohci, OHCI1394_IsochronousCycleTimer);
 
 	if (ohci->quirks & QUIRK_CYCLE_TIMER) {
@@ -2001,6 +2049,8 @@
 
 	ohci->generation = generation;
 	reg_write(ohci, OHCI1394_IntEventClear, OHCI1394_busReset);
+	if (param_debug & OHCI_PARAM_DEBUG_BUSRESETS)
+		reg_write(ohci, OHCI1394_IntMaskSet, OHCI1394_busReset);
 
 	if (ohci->quirks & QUIRK_RESET_PACKET)
 		ohci->request_generation = generation;
@@ -2067,12 +2117,14 @@
 		return IRQ_NONE;
 
 	/*
-	 * busReset and postedWriteErr must not be cleared yet
+	 * busReset and postedWriteErr events must not be cleared yet
 	 * (OHCI 1.1 clauses 7.2.3.2 and 13.2.8.1)
 	 */
 	reg_write(ohci, OHCI1394_IntEventClear,
 		  event & ~(OHCI1394_busReset | OHCI1394_postedWriteErr));
 	log_irqs(ohci, event);
+	if (event & OHCI1394_busReset)
+		reg_write(ohci, OHCI1394_IntMaskClear, OHCI1394_busReset);
 
 	if (event & OHCI1394_selfIDComplete)
 		queue_work(selfid_workqueue, &ohci->bus_reset_work);
@@ -3615,6 +3667,9 @@
 	if (param_quirks)
 		ohci->quirks = param_quirks;
 
+	if (detect_vt630x_with_asm1083_on_amd_ryzen_machine(dev))
+		ohci->quirks |= QUIRK_REBOOT_BY_CYCLE_TIMER_READ;
+
 	/*
 	 * Because dma_alloc_coherent() allocates at least one page,
 	 * we save space by using a common buffer for the AR request/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firewire/sbp2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firewire/sbp2.c
@@ -408,7 +408,7 @@
 			      void *payload, size_t length, void *callback_data)
 {
 	struct sbp2_logical_unit *lu = callback_data;
-	struct sbp2_orb *orb;
+	struct sbp2_orb *orb = NULL, *iter;
 	struct sbp2_status status;
 	unsigned long flags;
 
@@ -433,17 +433,18 @@
 
 	/* Lookup the orb corresponding to this status write. */
 	spin_lock_irqsave(&lu->tgt->lock, flags);
-	list_for_each_entry(orb, &lu->orb_list, link) {
+	list_for_each_entry(iter, &lu->orb_list, link) {
 		if (STATUS_GET_ORB_HIGH(status) == 0 &&
-		    STATUS_GET_ORB_LOW(status) == orb->request_bus) {
-			orb->rcode = RCODE_COMPLETE;
-			list_del(&orb->link);
+		    STATUS_GET_ORB_LOW(status) == iter->request_bus) {
+			iter->rcode = RCODE_COMPLETE;
+			list_del(&iter->link);
+			orb = iter;
 			break;
 		}
 	}
 	spin_unlock_irqrestore(&lu->tgt->lock, flags);
 
-	if (&orb->link != &lu->orb_list) {
+	if (orb) {
 		orb->callback(orb, &status);
 		kref_put(&orb->kref, free_orb); /* orb callback reference */
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/Kconfig
@@ -40,6 +40,7 @@
 config ARM_SDE_INTERFACE
 	bool "ARM Software Delegated Exception Interface (SDEI)"
 	depends on ARM64
+	depends on ACPI_APEI_GHES
 	help
 	  The Software Delegated Exception Interface (SDEI) is an ARM
 	  standard for registering callbacks from the platform firmware
@@ -138,7 +139,7 @@
 	select ISCSI_BOOT_SYSFS
 	select ISCSI_IBFT_FIND if X86
 	depends on ACPI && SCSI && SCSI_LOWLEVEL
-	default	n
+	default n
 	help
 	  This option enables support for detection and exposing of iSCSI
 	  Boot Firmware Table (iBFT) via sysfs to userspace. If you wish to
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_ffa/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_ffa/bus.c
@@ -15,6 +15,8 @@
 
 #include "common.h"
 
+static DEFINE_IDA(ffa_bus_id);
+
 static int ffa_device_match(struct device *dev, struct device_driver *drv)
 {
 	const struct ffa_device_id *id_table;
@@ -53,7 +55,8 @@
 {
 	struct ffa_driver *ffa_drv = to_ffa_driver(dev->driver);
 
-	ffa_drv->remove(to_ffa_dev(dev));
+	if (ffa_drv->remove)
+		ffa_drv->remove(to_ffa_dev(dev));
 }
 
 static int ffa_device_uevent(struct device *dev, struct kobj_uevent_env *env)
@@ -130,6 +133,7 @@
 {
 	struct ffa_device *ffa_dev = to_ffa_dev(dev);
 
+	ida_free(&ffa_bus_id, ffa_dev->id);
 	kfree(ffa_dev);
 }
 
@@ -169,19 +173,26 @@
 
 struct ffa_device *ffa_device_register(const uuid_t *uuid, int vm_id)
 {
-	int ret;
+	int id, ret;
 	struct device *dev;
 	struct ffa_device *ffa_dev;
 
+	id = ida_alloc_min(&ffa_bus_id, 1, GFP_KERNEL);
+	if (id < 0)
+		return NULL;
+
 	ffa_dev = kzalloc(sizeof(*ffa_dev), GFP_KERNEL);
-	if (!ffa_dev)
+	if (!ffa_dev) {
+		ida_free(&ffa_bus_id, id);
 		return NULL;
+	}
 
 	dev = &ffa_dev->dev;
 	dev->bus = &ffa_bus_type;
 	dev->release = ffa_release_device;
-	dev_set_name(&ffa_dev->dev, "arm-ffa-%04x", vm_id);
+	dev_set_name(&ffa_dev->dev, "arm-ffa-%d", id);
 
+	ffa_dev->id = id;
 	ffa_dev->vm_id = vm_id;
 	uuid_copy(&ffa_dev->uuid, uuid);
 
@@ -215,4 +226,5 @@
 {
 	ffa_devices_unregister();
 	bus_unregister(&ffa_bus_type);
+	ida_destroy(&ffa_bus_id);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_ffa/driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_ffa/driver.c
@@ -451,12 +451,18 @@
 		ep_mem_access->receiver = args->attrs[idx].receiver;
 		ep_mem_access->attrs = args->attrs[idx].attrs;
 		ep_mem_access->composite_off = COMPOSITE_OFFSET(args->nattrs);
+		ep_mem_access->flag = 0;
+		ep_mem_access->reserved = 0;
 	}
+	mem_region->handle = 0;
+	mem_region->reserved_0 = 0;
+	mem_region->reserved_1 = 0;
 	mem_region->ep_count = args->nattrs;
 
 	composite = buffer + COMPOSITE_OFFSET(args->nattrs);
 	composite->total_pg_cnt = ffa_get_num_pages_sg(args->sg);
 	composite->addr_range_cnt = num_entries;
+	composite->reserved = 0;
 
 	length = COMPOSITE_CONSTITUENTS_OFFSET(args->nattrs, num_entries);
 	frag_len = COMPOSITE_CONSTITUENTS_OFFSET(args->nattrs, 0);
@@ -491,6 +497,7 @@
 
 		constituents->address = sg_phys(args->sg);
 		constituents->pg_cnt = args->sg->length / FFA_PAGE_SIZE;
+		constituents->reserved = 0;
 		constituents++;
 		frag_len += sizeof(struct ffa_mem_region_addr_range);
 	} while ((args->sg = sg_next(args->sg)));
@@ -556,7 +563,7 @@
 		return -ENODEV;
 	}
 
-	count = ffa_partition_probe(&uuid_null, &pbuf);
+	count = ffa_partition_probe(&uuid, &pbuf);
 	if (count <= 0)
 		return -ENOENT;
 
@@ -645,8 +652,6 @@
 			       __func__, tpbuf->id);
 			continue;
 		}
-
-		ffa_dev_set_drvdata(ffa_dev, drv_info);
 	}
 	kfree(pbuf);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/base.c
@@ -34,6 +34,12 @@
 	__le16 reserved;
 };
 
+struct scmi_msg_resp_base_discover_agent {
+	__le32 agent_id;
+	u8 name[SCMI_MAX_STR_SIZE];
+};
+
+
 struct scmi_msg_base_error_notify {
 	__le32 event_control;
 #define BASE_TP_NOTIFY_ALL	BIT(0)
@@ -191,7 +197,7 @@
 			break;
 
 		loop_num_ret = le32_to_cpu(*num_ret);
-		if (tot_num_ret + loop_num_ret > MAX_PROTOCOLS_IMP) {
+		if (loop_num_ret > MAX_PROTOCOLS_IMP - tot_num_ret) {
 			dev_err(dev, "No. of Protocol > MAX_PROTOCOLS_IMP");
 			break;
 		}
@@ -225,18 +231,21 @@
 					int id, char *name)
 {
 	int ret;
+	struct scmi_msg_resp_base_discover_agent *agent_info;
 	struct scmi_xfer *t;
 
 	ret = ph->xops->xfer_get_init(ph, BASE_DISCOVER_AGENT,
-				      sizeof(__le32), SCMI_MAX_STR_SIZE, &t);
+				      sizeof(__le32), sizeof(*agent_info), &t);
 	if (ret)
 		return ret;
 
 	put_unaligned_le32(id, t->tx.buf);
 
 	ret = ph->xops->do_xfer(ph, t);
-	if (!ret)
-		strlcpy(name, t->rx.buf, SCMI_MAX_STR_SIZE);
+	if (!ret) {
+		agent_info = t->rx.buf;
+		strlcpy(name, agent_info->name, SCMI_MAX_STR_SIZE);
+	}
 
 	ph->xops->xfer_put(ph, t);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/bus.c
@@ -216,9 +216,20 @@
 	device_unregister(&scmi_dev->dev);
 }
 
+void scmi_device_link_add(struct device *consumer, struct device *supplier)
+{
+	struct device_link *link;
+
+	link = device_link_add(consumer, supplier, DL_FLAG_AUTOREMOVE_CONSUMER);
+
+	WARN_ON(!link);
+}
+
 void scmi_set_handle(struct scmi_device *scmi_dev)
 {
 	scmi_dev->handle = scmi_handle_get(&scmi_dev->dev);
+	if (scmi_dev->handle)
+		scmi_device_link_add(&scmi_dev->dev, scmi_dev->handle->dev);
 }
 
 int scmi_protocol_register(const struct scmi_protocol *proto)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/clock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/clock.c
@@ -204,7 +204,8 @@
 
 	if (rate_discrete && rate) {
 		clk->list.num_rates = tot_rate_cnt;
-		sort(rate, tot_rate_cnt, sizeof(*rate), rate_cmp_func, NULL);
+		sort(clk->list.rates, tot_rate_cnt, sizeof(*rate),
+		     rate_cmp_func, NULL);
 	}
 
 	clk->rate_discrete = rate_discrete;
@@ -314,9 +315,13 @@
 static const struct scmi_clock_info *
 scmi_clock_info_get(const struct scmi_protocol_handle *ph, u32 clk_id)
 {
+	struct scmi_clock_info *clk;
 	struct clock_info *ci = ph->get_priv(ph);
-	struct scmi_clock_info *clk = ci->clk + clk_id;
 
+	if (clk_id >= ci->num_clocks)
+		return NULL;
+
+	clk = ci->clk + clk_id;
 	if (!clk->name[0])
 		return NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/common.h
@@ -272,6 +272,7 @@
 struct scmi_revision_info *
 scmi_revision_area_get(const struct scmi_protocol_handle *ph);
 int scmi_handle_put(const struct scmi_handle *handle);
+void scmi_device_link_add(struct device *consumer, struct device *supplier);
 struct scmi_handle *scmi_handle_get(struct device *dev);
 void scmi_set_handle(struct scmi_device *scmi_dev);
 void scmi_setup_protocol_implemented(const struct scmi_protocol_handle *ph,
@@ -438,6 +439,7 @@
 void shmem_clear_channel(struct scmi_shared_mem __iomem *shmem);
 bool shmem_poll_done(struct scmi_shared_mem __iomem *shmem,
 		     struct scmi_xfer *xfer);
+bool shmem_channel_free(struct scmi_shared_mem __iomem *shmem);
 
 /* declarations for message passing transports */
 struct scmi_msg_payld;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/driver.c
@@ -652,7 +652,8 @@
 
 	xfer = scmi_xfer_command_acquire(cinfo, msg_hdr);
 	if (IS_ERR(xfer)) {
-		scmi_clear_channel(info, cinfo);
+		if (MSG_XTRACT_TYPE(msg_hdr) == MSG_TYPE_DELAYED_RESP)
+			scmi_clear_channel(info, cinfo);
 		return;
 	}
 
@@ -782,6 +783,8 @@
 			      xfer->hdr.protocol_id, xfer->hdr.seq,
 			      xfer->hdr.poll_completion);
 
+	/* Clear any stale status */
+	xfer->hdr.status = SCMI_SUCCESS;
 	xfer->state = SCMI_XFER_SENT_OK;
 	/*
 	 * Even though spinlocking is not needed here since no race is possible
@@ -1460,7 +1463,7 @@
 		return ret;
 
 	ret = __scmi_xfer_info_init(sinfo, &sinfo->tx_minfo);
-	if (!ret && idr_find(&sinfo->rx_idr, SCMI_PROTOCOL_BASE))
+	if (!ret && !idr_is_empty(&sinfo->rx_idr))
 		ret = __scmi_xfer_info_init(sinfo, &sinfo->rx_minfo);
 
 	return ret;
@@ -1515,8 +1518,12 @@
 {
 	int ret = scmi_chan_setup(info, dev, prot_id, true);
 
-	if (!ret) /* Rx is optional, hence no error check */
-		scmi_chan_setup(info, dev, prot_id, false);
+	if (!ret) {
+		/* Rx is optional, report only memory errors */
+		ret = scmi_chan_setup(info, dev, prot_id, false);
+		if (ret && ret != -ENOMEM)
+			ret = 0;
+	}
 
 	return ret;
 }
@@ -1726,10 +1733,16 @@
 			sdev = scmi_get_protocol_device(child, info,
 							id_table->protocol_id,
 							id_table->name);
-			/* Set handle if not already set: device existed */
-			if (sdev && !sdev->handle)
-				sdev->handle =
-					scmi_handle_get_from_info_unlocked(info);
+			if (sdev) {
+				/* Set handle if not already set: device existed */
+				if (!sdev->handle)
+					sdev->handle =
+						scmi_handle_get_from_info_unlocked(info);
+				/* Relink consumer and suppliers */
+				if (sdev->handle)
+					scmi_device_link_add(&sdev->dev,
+							     sdev->handle->dev);
+			}
 		} else {
 			dev_err(info->dev,
 				"Failed. SCMI protocol %d not active.\n",
@@ -1915,20 +1928,17 @@
 
 static int scmi_remove(struct platform_device *pdev)
 {
-	int ret = 0, id;
+	int ret, id;
 	struct scmi_info *info = platform_get_drvdata(pdev);
 	struct device_node *child;
 
 	mutex_lock(&scmi_list_mutex);
 	if (info->users)
-		ret = -EBUSY;
-	else
-		list_del(&info->node);
+		dev_warn(&pdev->dev,
+			 "Still active SCMI users will be forcibly unbound.\n");
+	list_del(&info->node);
 	mutex_unlock(&scmi_list_mutex);
 
-	if (ret)
-		return ret;
-
 	scmi_notification_exit(&info->handle);
 
 	mutex_lock(&info->protocols_mtx);
@@ -1940,7 +1950,11 @@
 	idr_destroy(&info->active_protocols);
 
 	/* Safe to free channels since no more users */
-	return scmi_cleanup_txrx_channels(info);
+	ret = scmi_cleanup_txrx_channels(info);
+	if (ret)
+		dev_warn(&pdev->dev, "Failed to cleanup SCMI channels.\n");
+
+	return 0;
 }
 
 static ssize_t protocol_version_show(struct device *dev,
@@ -2008,6 +2022,7 @@
 static struct platform_driver scmi_driver = {
 	.driver = {
 		   .name = "arm-scmi",
+		   .suppress_bind_attrs = true,
 		   .of_match_table = scmi_of_match,
 		   .dev_groups = versions_groups,
 		   },
@@ -2112,7 +2127,7 @@
 }
 module_exit(scmi_driver_exit);
 
-MODULE_ALIAS("platform: arm-scmi");
+MODULE_ALIAS("platform:arm-scmi");
 MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");
 MODULE_DESCRIPTION("ARM SCMI protocol driver");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/mailbox.c
@@ -43,6 +43,20 @@
 {
 	struct scmi_mailbox *smbox = client_to_scmi_mailbox(cl);
 
+	/*
+	 * An A2P IRQ is NOT valid when received while the platform still has
+	 * the ownership of the channel, because the platform at first releases
+	 * the SMT channel and then sends the completion interrupt.
+	 *
+	 * This addresses a possible race condition in which a spurious IRQ from
+	 * a previous timed-out reply which arrived late could be wrongly
+	 * associated with the next pending transaction.
+	 */
+	if (cl->knows_txdone && !shmem_channel_free(smbox->shmem)) {
+		dev_warn(smbox->cinfo->dev, "Ignoring spurious A2P IRQ !\n");
+		return;
+	}
+
 	scmi_rx_callback(smbox->cinfo, shmem_read_header(smbox->shmem), NULL);
 }
 
@@ -52,6 +66,39 @@
 					   "#mbox-cells", idx, NULL);
 }
 
+static int mailbox_chan_validate(struct device *cdev)
+{
+	int num_mb, num_sh, ret = 0;
+	struct device_node *np = cdev->of_node;
+
+	num_mb = of_count_phandle_with_args(np, "mboxes", "#mbox-cells");
+	num_sh = of_count_phandle_with_args(np, "shmem", NULL);
+	/* Bail out if mboxes and shmem descriptors are inconsistent */
+	if (num_mb <= 0 || num_sh > 2 || num_mb != num_sh) {
+		dev_warn(cdev, "Invalid channel descriptor for '%s'\n",
+			 of_node_full_name(np));
+		return -EINVAL;
+	}
+
+	if (num_sh > 1) {
+		struct device_node *np_tx, *np_rx;
+
+		np_tx = of_parse_phandle(np, "shmem", 0);
+		np_rx = of_parse_phandle(np, "shmem", 1);
+		/* SCMI Tx and Rx shared mem areas have to be distinct */
+		if (!np_tx || !np_rx || np_tx == np_rx) {
+			dev_warn(cdev, "Invalid shmem descriptor for '%s'\n",
+				 of_node_full_name(np));
+			ret = -EINVAL;
+		}
+
+		of_node_put(np_tx);
+		of_node_put(np_rx);
+	}
+
+	return ret;
+}
+
 static int mailbox_chan_setup(struct scmi_chan_info *cinfo, struct device *dev,
 			      bool tx)
 {
@@ -64,13 +111,19 @@
 	resource_size_t size;
 	struct resource res;
 
+	ret = mailbox_chan_validate(cdev);
+	if (ret)
+		return ret;
+
 	smbox = devm_kzalloc(dev, sizeof(*smbox), GFP_KERNEL);
 	if (!smbox)
 		return -ENOMEM;
 
 	shmem = of_parse_phandle(cdev->of_node, "shmem", idx);
-	if (!of_device_is_compatible(shmem, "arm,scmi-shmem"))
+	if (!of_device_is_compatible(shmem, "arm,scmi-shmem")) {
+		of_node_put(shmem);
 		return -ENXIO;
+	}
 
 	ret = of_address_to_resource(shmem, 0, &res);
 	of_node_put(shmem);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/reset.c
@@ -152,9 +152,13 @@
 	struct scmi_xfer *t;
 	struct scmi_msg_reset_domain_reset *dom;
 	struct scmi_reset_info *pi = ph->get_priv(ph);
-	struct reset_dom_info *rdom = pi->dom_info + domain;
+	struct reset_dom_info *rdom;
 
-	if (rdom->async_reset)
+	if (domain >= pi->num_domains)
+		return -EINVAL;
+
+	rdom = pi->dom_info + domain;
+	if (rdom->async_reset && flags & AUTONOMOUS_RESET)
 		flags |= ASYNCHRONOUS_RESET;
 
 	ret = ph->xops->xfer_get_init(ph, RESET, sizeof(*dom), 0, &t);
@@ -166,7 +170,7 @@
 	dom->flags = cpu_to_le32(flags);
 	dom->reset_state = cpu_to_le32(state);
 
-	if (rdom->async_reset)
+	if (flags & ASYNCHRONOUS_RESET)
 		ret = ph->xops->do_xfer_with_response(ph, t);
 	else
 		ret = ph->xops->do_xfer(ph, t);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/scmi_pm_domain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/scmi_pm_domain.c
@@ -8,7 +8,6 @@
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/module.h>
-#include <linux/pm_clock.h>
 #include <linux/pm_domain.h>
 #include <linux/scmi_protocol.h>
 
@@ -53,27 +52,6 @@
 	return scmi_pd_power(domain, false);
 }
 
-static int scmi_pd_attach_dev(struct generic_pm_domain *pd, struct device *dev)
-{
-	int ret;
-
-	ret = pm_clk_create(dev);
-	if (ret)
-		return ret;
-
-	ret = of_pm_clk_add_clks(dev);
-	if (ret >= 0)
-		return 0;
-
-	pm_clk_destroy(dev);
-	return ret;
-}
-
-static void scmi_pd_detach_dev(struct generic_pm_domain *pd, struct device *dev)
-{
-	pm_clk_destroy(dev);
-}
-
 static int scmi_pm_domain_probe(struct scmi_device *sdev)
 {
 	int num_domains, i;
@@ -124,10 +102,6 @@
 		scmi_pd->genpd.name = scmi_pd->name;
 		scmi_pd->genpd.power_off = scmi_pd_power_off;
 		scmi_pd->genpd.power_on = scmi_pd_power_on;
-		scmi_pd->genpd.attach_dev = scmi_pd_attach_dev;
-		scmi_pd->genpd.detach_dev = scmi_pd_detach_dev;
-		scmi_pd->genpd.flags = GENPD_FLAG_PM_CLK |
-				       GENPD_FLAG_ACTIVE_WAKEUP;
 
 		pm_genpd_init(&scmi_pd->genpd, NULL,
 			      state == SCMI_POWER_STATE_GENERIC_OFF);
@@ -138,9 +112,26 @@
 	scmi_pd_data->domains = domains;
 	scmi_pd_data->num_domains = num_domains;
 
-	of_genpd_add_provider_onecell(np, scmi_pd_data);
+	dev_set_drvdata(dev, scmi_pd_data);
 
-	return 0;
+	return of_genpd_add_provider_onecell(np, scmi_pd_data);
+}
+
+static void scmi_pm_domain_remove(struct scmi_device *sdev)
+{
+	int i;
+	struct genpd_onecell_data *scmi_pd_data;
+	struct device *dev = &sdev->dev;
+	struct device_node *np = dev->of_node;
+
+	of_genpd_del_provider(np);
+
+	scmi_pd_data = dev_get_drvdata(dev);
+	for (i = 0; i < scmi_pd_data->num_domains; i++) {
+		if (!scmi_pd_data->domains[i])
+			continue;
+		pm_genpd_remove(scmi_pd_data->domains[i]);
+	}
 }
 
 static const struct scmi_device_id scmi_id_table[] = {
@@ -152,6 +143,7 @@
 static struct scmi_driver scmi_power_domain_driver = {
 	.name = "scmi-power-domain",
 	.probe = scmi_pm_domain_probe,
+	.remove = scmi_pm_domain_remove,
 	.id_table = scmi_id_table,
 };
 module_scmi_driver(scmi_power_domain_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/sensors.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/sensors.c
@@ -631,16 +631,19 @@
 {
 	int ret;
 	struct scmi_xfer *t;
+	struct sensors_info *si = ph->get_priv(ph);
+
+	if (sensor_id >= si->num_sensors)
+		return -EINVAL;
 
 	ret = ph->xops->xfer_get_init(ph, SENSOR_CONFIG_GET,
 				      sizeof(__le32), sizeof(__le32), &t);
 	if (ret)
 		return ret;
 
-	put_unaligned_le32(cpu_to_le32(sensor_id), t->tx.buf);
+	put_unaligned_le32(sensor_id, t->tx.buf);
 	ret = ph->xops->do_xfer(ph, t);
 	if (!ret) {
-		struct sensors_info *si = ph->get_priv(ph);
 		struct scmi_sensor_info *s = si->sensors + sensor_id;
 
 		*sensor_config = get_unaligned_le64(t->rx.buf);
@@ -657,6 +660,10 @@
 	int ret;
 	struct scmi_xfer *t;
 	struct scmi_msg_sensor_config_set *msg;
+	struct sensors_info *si = ph->get_priv(ph);
+
+	if (sensor_id >= si->num_sensors)
+		return -EINVAL;
 
 	ret = ph->xops->xfer_get_init(ph, SENSOR_CONFIG_SET,
 				      sizeof(*msg), 0, &t);
@@ -669,7 +676,6 @@
 
 	ret = ph->xops->do_xfer(ph, t);
 	if (!ret) {
-		struct sensors_info *si = ph->get_priv(ph);
 		struct scmi_sensor_info *s = si->sensors + sensor_id;
 
 		s->sensor_config = sensor_config;
@@ -700,8 +706,11 @@
 	int ret;
 	struct scmi_xfer *t;
 	struct scmi_msg_sensor_reading_get *sensor;
+	struct scmi_sensor_info *s;
 	struct sensors_info *si = ph->get_priv(ph);
-	struct scmi_sensor_info *s = si->sensors + sensor_id;
+
+	if (sensor_id >= si->num_sensors)
+		return -EINVAL;
 
 	ret = ph->xops->xfer_get_init(ph, SENSOR_READING_GET,
 				      sizeof(*sensor), 0, &t);
@@ -710,6 +719,7 @@
 
 	sensor = t->tx.buf;
 	sensor->id = cpu_to_le32(sensor_id);
+	s = si->sensors + sensor_id;
 	if (s->async) {
 		sensor->flags = cpu_to_le32(SENSOR_READ_ASYNC);
 		ret = ph->xops->do_xfer_with_response(ph, t);
@@ -764,9 +774,13 @@
 	int ret;
 	struct scmi_xfer *t;
 	struct scmi_msg_sensor_reading_get *sensor;
+	struct scmi_sensor_info *s;
 	struct sensors_info *si = ph->get_priv(ph);
-	struct scmi_sensor_info *s = si->sensors + sensor_id;
 
+	if (sensor_id >= si->num_sensors)
+		return -EINVAL;
+
+	s = si->sensors + sensor_id;
 	if (!count || !readings ||
 	    (!s->num_axis && count > 1) || (s->num_axis && count > s->num_axis))
 		return -EINVAL;
@@ -817,6 +831,9 @@
 {
 	struct sensors_info *si = ph->get_priv(ph);
 
+	if (sensor_id >= si->num_sensors)
+		return NULL;
+
 	return si->sensors + sensor_id;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/shmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/shmem.c
@@ -58,10 +58,11 @@
 void shmem_fetch_response(struct scmi_shared_mem __iomem *shmem,
 			  struct scmi_xfer *xfer)
 {
+	size_t len = ioread32(&shmem->length);
+
 	xfer->hdr.status = ioread32(shmem->msg_payload);
 	/* Skip the length of header and status in shmem area i.e 8 bytes */
-	xfer->rx.len = min_t(size_t, xfer->rx.len,
-			     ioread32(&shmem->length) - 8);
+	xfer->rx.len = min_t(size_t, xfer->rx.len, len > 8 ? len - 8 : 0);
 
 	/* Take a copy to the rx buffer.. */
 	memcpy_fromio(xfer->rx.buf, shmem->msg_payload + 4, xfer->rx.len);
@@ -70,8 +71,10 @@
 void shmem_fetch_notification(struct scmi_shared_mem __iomem *shmem,
 			      size_t max_len, struct scmi_xfer *xfer)
 {
+	size_t len = ioread32(&shmem->length);
+
 	/* Skip only the length of header in shmem area i.e 4 bytes */
-	xfer->rx.len = min_t(size_t, max_len, ioread32(&shmem->length) - 4);
+	xfer->rx.len = min_t(size_t, max_len, len > 4 ? len - 4 : 0);
 
 	/* Take a copy to the rx buffer.. */
 	memcpy_fromio(xfer->rx.buf, shmem->msg_payload, xfer->rx.len);
@@ -96,3 +99,9 @@
 		(SCMI_SHMEM_CHAN_STAT_CHANNEL_ERROR |
 		 SCMI_SHMEM_CHAN_STAT_CHANNEL_FREE);
 }
+
+bool shmem_channel_free(struct scmi_shared_mem __iomem *shmem)
+{
+	return (ioread32(&shmem->channel_status) &
+			SCMI_SHMEM_CHAN_STAT_CHANNEL_FREE);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/smc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/smc.c
@@ -76,8 +76,10 @@
 		return -ENOMEM;
 
 	np = of_parse_phandle(cdev->of_node, "shmem", 0);
-	if (!of_device_is_compatible(np, "arm,scmi-shmem"))
+	if (!of_device_is_compatible(np, "arm,scmi-shmem")) {
+		of_node_put(np);
 		return -ENXIO;
+	}
 
 	ret = of_address_to_resource(np, 0, &res);
 	of_node_put(np);
@@ -128,6 +130,15 @@
 	struct scmi_chan_info *cinfo = p;
 	struct scmi_smc *scmi_info = cinfo->transport_info;
 
+	/*
+	 * Different protocols might share the same chan info, so a previous
+	 * smc_chan_free call might have already freed the structure.
+	 */
+	if (!scmi_info) {
+		scmi_free_channel(cinfo, data, id);
+		return 0;
+	}
+
 	cinfo->transport_info = NULL;
 	scmi_info->cinfo = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/virtio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/virtio.c
@@ -82,7 +82,8 @@
 }
 
 static int scmi_vio_feed_vq_rx(struct scmi_vio_channel *vioch,
-			       struct scmi_vio_msg *msg)
+			       struct scmi_vio_msg *msg,
+			       struct device *dev)
 {
 	struct scatterlist sg_in;
 	int rc;
@@ -94,8 +95,7 @@
 
 	rc = virtqueue_add_inbuf(vioch->vqueue, &sg_in, 1, msg, GFP_ATOMIC);
 	if (rc)
-		dev_err_once(vioch->cinfo->dev,
-			     "failed to add to virtqueue (%d)\n", rc);
+		dev_err_once(dev, "failed to add to virtqueue (%d)\n", rc);
 	else
 		virtqueue_kick(vioch->vqueue);
 
@@ -108,7 +108,7 @@
 				  struct scmi_vio_msg *msg)
 {
 	if (vioch->is_rx) {
-		scmi_vio_feed_vq_rx(vioch, msg);
+		scmi_vio_feed_vq_rx(vioch, msg, vioch->cinfo->dev);
 	} else {
 		/* Here IRQs are assumed to be already disabled by the caller */
 		spin_lock(&vioch->lock);
@@ -247,19 +247,19 @@
 	for (i = 0; i < vioch->max_msg; i++) {
 		struct scmi_vio_msg *msg;
 
-		msg = devm_kzalloc(cinfo->dev, sizeof(*msg), GFP_KERNEL);
+		msg = devm_kzalloc(dev, sizeof(*msg), GFP_KERNEL);
 		if (!msg)
 			return -ENOMEM;
 
 		if (tx) {
-			msg->request = devm_kzalloc(cinfo->dev,
+			msg->request = devm_kzalloc(dev,
 						    VIRTIO_SCMI_MAX_PDU_SIZE,
 						    GFP_KERNEL);
 			if (!msg->request)
 				return -ENOMEM;
 		}
 
-		msg->input = devm_kzalloc(cinfo->dev, VIRTIO_SCMI_MAX_PDU_SIZE,
+		msg->input = devm_kzalloc(dev, VIRTIO_SCMI_MAX_PDU_SIZE,
 					  GFP_KERNEL);
 		if (!msg->input)
 			return -ENOMEM;
@@ -269,7 +269,7 @@
 			list_add_tail(&msg->list, &vioch->free_list);
 			spin_unlock_irqrestore(&vioch->lock, flags);
 		} else {
-			scmi_vio_feed_vq_rx(vioch, msg);
+			scmi_vio_feed_vq_rx(vioch, msg, cinfo->dev);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scmi/voltage.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scmi/voltage.c
@@ -156,7 +156,7 @@
 			int cnt;
 
 			cmd->domain_id = cpu_to_le32(v->id);
-			cmd->level_index = desc_index;
+			cmd->level_index = cpu_to_le32(desc_index);
 			ret = ph->xops->do_xfer(ph, tl);
 			if (ret)
 				break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_scpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_scpi.c
@@ -627,6 +627,9 @@
 	if (ret)
 		return ERR_PTR(ret);
 
+	if (!buf.opp_count)
+		return ERR_PTR(-ENOENT);
+
 	info = kmalloc(sizeof(*info), GFP_KERNEL);
 	if (!info)
 		return ERR_PTR(-ENOMEM);
@@ -815,7 +818,7 @@
 		info->firmware_version = le32_to_cpu(caps.platform_version);
 	}
 	/* Ignore error if not implemented */
-	if (scpi_info->is_legacy && ret == -EOPNOTSUPP)
+	if (info->is_legacy && ret == -EOPNOTSUPP)
 		return 0;
 
 	return ret;
@@ -913,13 +916,14 @@
 	struct resource res;
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
+	struct scpi_drvinfo *scpi_drvinfo;
 
-	scpi_info = devm_kzalloc(dev, sizeof(*scpi_info), GFP_KERNEL);
-	if (!scpi_info)
+	scpi_drvinfo = devm_kzalloc(dev, sizeof(*scpi_drvinfo), GFP_KERNEL);
+	if (!scpi_drvinfo)
 		return -ENOMEM;
 
 	if (of_match_device(legacy_scpi_of_match, &pdev->dev))
-		scpi_info->is_legacy = true;
+		scpi_drvinfo->is_legacy = true;
 
 	count = of_count_phandle_with_args(np, "mboxes", "#mbox-cells");
 	if (count < 0) {
@@ -927,19 +931,19 @@
 		return -ENODEV;
 	}
 
-	scpi_info->channels = devm_kcalloc(dev, count, sizeof(struct scpi_chan),
-					   GFP_KERNEL);
-	if (!scpi_info->channels)
+	scpi_drvinfo->channels =
+		devm_kcalloc(dev, count, sizeof(struct scpi_chan), GFP_KERNEL);
+	if (!scpi_drvinfo->channels)
 		return -ENOMEM;
 
-	ret = devm_add_action(dev, scpi_free_channels, scpi_info);
+	ret = devm_add_action(dev, scpi_free_channels, scpi_drvinfo);
 	if (ret)
 		return ret;
 
-	for (; scpi_info->num_chans < count; scpi_info->num_chans++) {
+	for (; scpi_drvinfo->num_chans < count; scpi_drvinfo->num_chans++) {
 		resource_size_t size;
-		int idx = scpi_info->num_chans;
-		struct scpi_chan *pchan = scpi_info->channels + idx;
+		int idx = scpi_drvinfo->num_chans;
+		struct scpi_chan *pchan = scpi_drvinfo->channels + idx;
 		struct mbox_client *cl = &pchan->cl;
 		struct device_node *shmem = of_parse_phandle(np, "shmem", idx);
 
@@ -986,45 +990,53 @@
 		return ret;
 	}
 
-	scpi_info->commands = scpi_std_commands;
+	scpi_drvinfo->commands = scpi_std_commands;
 
-	platform_set_drvdata(pdev, scpi_info);
+	platform_set_drvdata(pdev, scpi_drvinfo);
 
-	if (scpi_info->is_legacy) {
+	if (scpi_drvinfo->is_legacy) {
 		/* Replace with legacy variants */
 		scpi_ops.clk_set_val = legacy_scpi_clk_set_val;
-		scpi_info->commands = scpi_legacy_commands;
+		scpi_drvinfo->commands = scpi_legacy_commands;
 
 		/* Fill priority bitmap */
 		for (idx = 0; idx < ARRAY_SIZE(legacy_hpriority_cmds); idx++)
 			set_bit(legacy_hpriority_cmds[idx],
-				scpi_info->cmd_priority);
+				scpi_drvinfo->cmd_priority);
 	}
 
-	ret = scpi_init_versions(scpi_info);
+	scpi_info = scpi_drvinfo;
+
+	ret = scpi_init_versions(scpi_drvinfo);
 	if (ret) {
 		dev_err(dev, "incorrect or no SCP firmware found\n");
+		scpi_info = NULL;
 		return ret;
 	}
 
-	if (scpi_info->is_legacy && !scpi_info->protocol_version &&
-	    !scpi_info->firmware_version)
+	if (scpi_drvinfo->is_legacy && !scpi_drvinfo->protocol_version &&
+	    !scpi_drvinfo->firmware_version)
 		dev_info(dev, "SCP Protocol legacy pre-1.0 firmware\n");
 	else
 		dev_info(dev, "SCP Protocol %lu.%lu Firmware %lu.%lu.%lu version\n",
 			 FIELD_GET(PROTO_REV_MAJOR_MASK,
-				   scpi_info->protocol_version),
+				   scpi_drvinfo->protocol_version),
 			 FIELD_GET(PROTO_REV_MINOR_MASK,
-				   scpi_info->protocol_version),
+				   scpi_drvinfo->protocol_version),
 			 FIELD_GET(FW_REV_MAJOR_MASK,
-				   scpi_info->firmware_version),
+				   scpi_drvinfo->firmware_version),
 			 FIELD_GET(FW_REV_MINOR_MASK,
-				   scpi_info->firmware_version),
+				   scpi_drvinfo->firmware_version),
 			 FIELD_GET(FW_REV_PATCH_MASK,
-				   scpi_info->firmware_version));
-	scpi_info->scpi_ops = &scpi_ops;
+				   scpi_drvinfo->firmware_version));
+
+	scpi_drvinfo->scpi_ops = &scpi_ops;
 
-	return devm_of_platform_populate(dev);
+	ret = devm_of_platform_populate(dev);
+	if (ret)
+		scpi_info = NULL;
+
+	return ret;
 }
 
 static const struct of_device_id scpi_of_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/arm_sdei.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/arm_sdei.c
@@ -43,6 +43,8 @@
 /* entry point from firmware to arch asm code */
 static unsigned long sdei_entry_point;
 
+static int sdei_hp_state;
+
 struct sdei_event {
 	/* These three are protected by the sdei_list_lock */
 	struct list_head	list;
@@ -301,8 +303,6 @@
 {
 	int err;
 
-	WARN_ON_ONCE(preemptible());
-
 	err = invoke_sdei_fn(SDEI_1_0_FN_SDEI_PE_MASK, 0, 0, 0, 0, 0, NULL);
 	if (err && err != -EIO) {
 		pr_warn_once("failed to mask CPU[%u]: %d\n",
@@ -315,6 +315,7 @@
 
 static void _ipi_mask_cpu(void *ignored)
 {
+	WARN_ON_ONCE(preemptible());
 	sdei_mask_local_cpu();
 }
 
@@ -322,8 +323,6 @@
 {
 	int err;
 
-	WARN_ON_ONCE(preemptible());
-
 	err = invoke_sdei_fn(SDEI_1_0_FN_SDEI_PE_UNMASK, 0, 0, 0, 0, 0, NULL);
 	if (err && err != -EIO) {
 		pr_warn_once("failed to unmask CPU[%u]: %d\n",
@@ -336,6 +335,7 @@
 
 static void _ipi_unmask_cpu(void *ignored)
 {
+	WARN_ON_ONCE(preemptible());
 	sdei_unmask_local_cpu();
 }
 
@@ -343,6 +343,8 @@
 {
 	int err;
 
+	WARN_ON_ONCE(preemptible());
+
 	err = invoke_sdei_fn(SDEI_1_0_FN_SDEI_PRIVATE_RESET, 0, 0, 0, 0, 0,
 			     NULL);
 	if (err && err != -EIO)
@@ -389,8 +391,6 @@
 	int err;
 	struct sdei_crosscall_args *arg = data;
 
-	WARN_ON_ONCE(preemptible());
-
 	err = sdei_api_event_enable(arg->event->event_num);
 
 	sdei_cross_call_return(arg, err);
@@ -479,8 +479,6 @@
 	int err;
 	struct sdei_crosscall_args *arg = data;
 
-	WARN_ON_ONCE(preemptible());
-
 	err = sdei_api_event_unregister(arg->event->event_num);
 
 	sdei_cross_call_return(arg, err);
@@ -561,8 +559,6 @@
 	struct sdei_registered_event *reg;
 	struct sdei_crosscall_args *arg = data;
 
-	WARN_ON(preemptible());
-
 	reg = per_cpu_ptr(arg->event->private_registered, smp_processor_id());
 	err = sdei_api_event_register(arg->event->event_num, sdei_entry_point,
 				      reg, 0, 0);
@@ -717,6 +713,8 @@
 {
 	int rv;
 
+	WARN_ON_ONCE(preemptible());
+
 	switch (action) {
 	case CPU_PM_ENTER:
 		rv = sdei_mask_local_cpu();
@@ -765,7 +763,7 @@
 	int err;
 
 	/* unregister private events */
-	cpuhp_remove_state(CPUHP_AP_ARM_SDEI_STARTING);
+	cpuhp_remove_state(sdei_hp_state);
 
 	err = sdei_unregister_shared();
 	if (err)
@@ -786,12 +784,15 @@
 		return err;
 	}
 
-	err = cpuhp_setup_state(CPUHP_AP_ARM_SDEI_STARTING, "SDEI",
+	err = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "SDEI",
 				&sdei_cpuhp_up, &sdei_cpuhp_down);
-	if (err)
+	if (err < 0) {
 		pr_warn("Failed to re-register CPU hotplug notifier...\n");
+		return err;
+	}
 
-	return err;
+	sdei_hp_state = err;
+	return 0;
 }
 
 static int sdei_device_restore(struct device *dev)
@@ -823,7 +824,7 @@
 	 * We are going to reset the interface, after this there is no point
 	 * doing work when we take CPUs offline.
 	 */
-	cpuhp_remove_state(CPUHP_AP_ARM_SDEI_STARTING);
+	cpuhp_remove_state(sdei_hp_state);
 
 	sdei_platform_reset();
 
@@ -1003,13 +1004,15 @@
 		goto remove_cpupm;
 	}
 
-	err = cpuhp_setup_state(CPUHP_AP_ARM_SDEI_STARTING, "SDEI",
+	err = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "SDEI",
 				&sdei_cpuhp_up, &sdei_cpuhp_down);
-	if (err) {
+	if (err < 0) {
 		pr_warn("Failed to register CPU hotplug notifier...\n");
 		goto remove_reboot;
 	}
 
+	sdei_hp_state = err;
+
 	return 0;
 
 remove_reboot:
@@ -1059,14 +1062,14 @@
 	return true;
 }
 
-static int __init sdei_init(void)
+void __init sdei_init(void)
 {
 	struct platform_device *pdev;
 	int ret;
 
 	ret = platform_driver_register(&sdei_driver);
 	if (ret || !sdei_present_acpi())
-		return ret;
+		return;
 
 	pdev = platform_device_register_simple(sdei_driver.driver.name,
 					       0, NULL, 0);
@@ -1076,17 +1079,8 @@
 		pr_info("Failed to register ACPI:SDEI platform device %d\n",
 			ret);
 	}
-
-	return ret;
 }
 
-/*
- * On an ACPI system SDEI needs to be ready before HEST:GHES tries to register
- * its events. ACPI is initialised from a subsys_initcall(), GHES is initialised
- * by device_initcall(). We want to be called in the middle.
- */
-subsys_initcall_sync(sdei_init);
-
 int sdei_event_handler(struct pt_regs *regs,
 		       struct sdei_registered_event *arg)
 {
@@ -1101,3 +1095,22 @@
 	return err;
 }
 NOKPROBE_SYMBOL(sdei_event_handler);
+
+void sdei_handler_abort(void)
+{
+	/*
+	 * If the crash happened in an SDEI event handler then we need to
+	 * finish the handler with the firmware so that we can have working
+	 * interrupts in the crash kernel.
+	 */
+	if (__this_cpu_read(sdei_active_critical_event)) {
+	        pr_warn("still in SDEI critical event context, attempting to finish handler.\n");
+	        __sdei_handler_abort();
+	        __this_cpu_write(sdei_active_critical_event, NULL);
+	}
+	if (__this_cpu_read(sdei_active_normal_event)) {
+	        pr_warn("still in SDEI normal event context, attempting to finish handler.\n");
+	        __sdei_handler_abort();
+	        __this_cpu_write(sdei_active_normal_event, NULL);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/dmi-id.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/dmi-id.c
@@ -169,9 +169,14 @@
 	return 0;
 }
 
+static void dmi_dev_release(struct device *dev)
+{
+	kfree(dev);
+}
+
 static struct class dmi_class = {
 	.name = "dmi",
-	.dev_release = (void(*)(struct device *)) kfree,
+	.dev_release = dmi_dev_release,
 	.dev_uevent = dmi_dev_uevent,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/dmi-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/dmi-sysfs.c
@@ -602,16 +602,16 @@
 	*ret = kobject_init_and_add(&entry->kobj, &dmi_sysfs_entry_ktype, NULL,
 				    "%d-%d", dh->type, entry->instance);
 
-	if (*ret) {
-		kfree(entry);
-		return;
-	}
-
 	/* Thread on the global list for cleanup */
 	spin_lock(&entry_list_lock);
 	list_add_tail(&entry->list, &entry_list);
 	spin_unlock(&entry_list_lock);
 
+	if (*ret) {
+		kobject_put(&entry->kobj);
+		return;
+	}
+
 	/* Handle specializations by type */
 	switch (dh->type) {
 	case DMI_ENTRY_SYSTEM_EVENT_LOG:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/dmi_scan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/dmi_scan.c
@@ -102,6 +102,17 @@
 		const struct dmi_header *dm = (const struct dmi_header *)data;
 
 		/*
+		 * If a short entry is found (less than 4 bytes), not only it
+		 * is invalid, but we cannot reliably locate the next entry.
+		 */
+		if (dm->length < sizeof(struct dmi_header)) {
+			pr_warn(FW_BUG
+				"Corrupted DMI table, offset %zd (only %d entries processed)\n",
+				data - buf, i);
+			break;
+		}
+
+		/*
 		 *  We want to know the total length (formatted area and
 		 *  strings) before decoding to make sure we won't run off the
 		 *  table in dmi_decode or dmi_string
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/Makefile
@@ -28,6 +28,7 @@
 obj-$(CONFIG_EFI_BOOTLOADER_CONTROL)	+= efibc.o
 obj-$(CONFIG_EFI_TEST)			+= test/
 obj-$(CONFIG_EFI_DEV_PATH_PARSER)	+= dev-path-parser.o
+obj-$(CONFIG_EFI)			+= secureboot.o
 obj-$(CONFIG_APPLE_PROPERTIES)		+= apple-properties.o
 obj-$(CONFIG_EFI_RCI2_TABLE)		+= rci2-table.o
 obj-$(CONFIG_EFI_EMBEDDED_FIRMWARE)	+= embedded-firmware.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/apple-properties.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/apple-properties.c
@@ -24,7 +24,7 @@
 static int __init dump_properties_enable(char *arg)
 {
 	dump_properties = true;
-	return 0;
+	return 1;
 }
 
 __setup("dump_apple_properties", dump_properties_enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/arm-runtime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/arm-runtime.c
@@ -107,7 +107,7 @@
 		efi_memory_desc_t *md;
 
 		for_each_efi_memory_desc(md) {
-			int md_size = md->num_pages << EFI_PAGE_SHIFT;
+			u64 md_size = md->num_pages << EFI_PAGE_SHIFT;
 			struct resource *res;
 
 			if (!(md->attribute & EFI_MEMORY_SP))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/capsule-loader.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/capsule-loader.c
@@ -243,29 +243,6 @@
 }
 
 /**
- * efi_capsule_flush - called by file close or file flush
- * @file: file pointer
- * @id: not used
- *
- *	If a capsule is being partially uploaded then calling this function
- *	will be treated as upload termination and will free those completed
- *	buffer pages and -ECANCELED will be returned.
- **/
-static int efi_capsule_flush(struct file *file, fl_owner_t id)
-{
-	int ret = 0;
-	struct capsule_info *cap_info = file->private_data;
-
-	if (cap_info->index > 0) {
-		pr_err("capsule upload not complete\n");
-		efi_free_all_buff_pages(cap_info);
-		ret = -ECANCELED;
-	}
-
-	return ret;
-}
-
-/**
  * efi_capsule_release - called by file close
  * @inode: not used
  * @file: file pointer
@@ -277,6 +254,13 @@
 {
 	struct capsule_info *cap_info = file->private_data;
 
+	if (cap_info->index > 0 &&
+	    (cap_info->header.headersize == 0 ||
+	     cap_info->count < cap_info->total_size)) {
+		pr_err("capsule upload not complete\n");
+		efi_free_all_buff_pages(cap_info);
+	}
+
 	kfree(cap_info->pages);
 	kfree(cap_info->phys);
 	kfree(file->private_data);
@@ -308,7 +292,7 @@
 		return -ENOMEM;
 	}
 
-	cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
+	cap_info->phys = kzalloc(sizeof(phys_addr_t), GFP_KERNEL);
 	if (!cap_info->phys) {
 		kfree(cap_info->pages);
 		kfree(cap_info);
@@ -324,7 +308,6 @@
 	.owner = THIS_MODULE,
 	.open = efi_capsule_open,
 	.write = efi_capsule_write,
-	.flush = efi_capsule_flush,
 	.release = efi_capsule_release,
 	.llseek = no_llseek,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/efi-init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/efi-init.c
@@ -19,6 +19,7 @@
 #include <linux/of_fdt.h>
 #include <linux/platform_device.h>
 #include <linux/screen_info.h>
+#include <linux/security.h>
 
 #include <asm/efi.h>
 
@@ -142,15 +143,6 @@
 	case EFI_CONVENTIONAL_MEMORY:
 	case EFI_PERSISTENT_MEMORY:
 		/*
-		 * Special purpose memory is 'soft reserved', which means it
-		 * is set aside initially, but can be hotplugged back in or
-		 * be assigned to the dax driver after boot.
-		 */
-		if (efi_soft_reserve_enabled() &&
-		    (md->attribute & EFI_MEMORY_SP))
-			return false;
-
-		/*
 		 * According to the spec, these regions are no longer reserved
 		 * after calling ExitBootServices(). However, we can only use
 		 * them as System RAM if they can be mapped writeback cacheable.
@@ -194,6 +186,16 @@
 		size = npages << PAGE_SHIFT;
 
 		if (is_memory(md)) {
+			/*
+			 * Special purpose memory is 'soft reserved', which
+			 * means it is set aside initially. Don't add a memblock
+			 * for it now so that it can be hotplugged back in or
+			 * be assigned to the dax driver after boot.
+			 */
+			if (efi_soft_reserve_enabled() &&
+			    (md->attribute & EFI_MEMORY_SP))
+				continue;
+
 			early_init_dt_add_memory_arch(paddr, size);
 
 			if (!is_usable_memory(md))
@@ -234,7 +236,19 @@
 		return;
 	}
 
+	efi_set_secure_boot(efi_get__secure_boot());
+
+#ifdef CONFIG_LOCK_DOWN_IN_SECURE_BOOT
+	if (efi_enabled(EFI_SECURE_BOOT))
+		security_lock_kernel_down("EFI Secure Boot mode", LOCKDOWN_INTEGRITY_MAX);
+#endif
+
 	reserve_regions();
+	/*
+	 * For memblock manipulation, the cap should come after the memblock_add().
+	 * And now, memblock is fully populated, it is time to do capping.
+	 */
+	early_init_dt_check_for_usable_mem_range();
 	efi_esrt_init();
 	efi_mokvar_table_init();
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/efi-pstore.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/efi-pstore.c
@@ -266,7 +266,7 @@
 		efi_name[i] = name[i];
 
 	ret = efivar_entry_set_safe(efi_name, vendor, PSTORE_EFI_ATTRIBUTES,
-			      preemptible(), record->size, record->psi->buf);
+			      false, record->size, record->psi->buf);
 
 	if (record->reason == KMSG_DUMP_OOPS && try_module_get(THIS_MODULE))
 		if (!schedule_work(&efivar_work))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/efi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/efi.c
@@ -31,6 +31,7 @@
 #include <linux/ucs2_string.h>
 #include <linux/memblock.h>
 #include <linux/security.h>
+#include <linux/bsearch.h>
 
 #include <asm/early_ioremap.h>
 
@@ -209,7 +210,7 @@
 		memcpy(efivar_ssdt, str, strlen(str));
 	else
 		pr_warn("efivar_ssdt: name too long: %s\n", str);
-	return 0;
+	return 1;
 }
 __setup("efivar_ssdt=", efivar_ssdt_setup);
 
@@ -385,8 +386,8 @@
 	efi_kobj = kobject_create_and_add("efi", firmware_kobj);
 	if (!efi_kobj) {
 		pr_err("efi: Firmware registration failed.\n");
-		destroy_workqueue(efi_rts_wq);
-		return -ENOMEM;
+		error = -ENOMEM;
+		goto err_destroy_wq;
 	}
 
 	if (efi_rt_services_supported(EFI_RT_SUPPORTED_GET_VARIABLE |
@@ -429,7 +430,10 @@
 		generic_ops_unregister();
 err_put:
 	kobject_put(efi_kobj);
-	destroy_workqueue(efi_rts_wq);
+err_destroy_wq:
+	if (efi_rts_wq)
+		destroy_workqueue(efi_rts_wq);
+
 	return error;
 }
 
@@ -590,7 +594,7 @@
 
 		seed = early_memremap(efi_rng_seed, sizeof(*seed));
 		if (seed != NULL) {
-			size = READ_ONCE(seed->size);
+			size = min_t(u32, seed->size, SZ_1K); // sanity check
 			early_memunmap(seed, sizeof(*seed));
 		} else {
 			pr_err("Could not map UEFI random seed!\n");
@@ -599,8 +603,8 @@
 			seed = early_memremap(efi_rng_seed,
 					      sizeof(*seed) + size);
 			if (seed != NULL) {
-				pr_notice("seeding entropy pool\n");
 				add_bootloader_randomness(seed->bits, size);
+				memzero_explicit(seed->bits, size);
 				early_memunmap(seed, sizeof(*seed) + size);
 			} else {
 				pr_err("Could not map UEFI random seed!\n");
@@ -719,6 +723,13 @@
 		systab_hdr->revision >> 16,
 		systab_hdr->revision & 0xffff,
 		vendor);
+
+	if (IS_ENABLED(CONFIG_X86_64) &&
+	    systab_hdr->revision > EFI_1_10_SYSTEM_TABLE_REVISION &&
+	    !strcmp(vendor, "Apple")) {
+		pr_info("Apple Mac detected, using EFI v1.10 runtime services only\n");
+		efi.runtime_version = EFI_1_10_SYSTEM_TABLE_REVISION;
+	}
 }
 
 static __initdata char memory_type_name[][13] = {
@@ -764,13 +775,15 @@
 		     EFI_MEMORY_WB | EFI_MEMORY_UCE | EFI_MEMORY_RO |
 		     EFI_MEMORY_WP | EFI_MEMORY_RP | EFI_MEMORY_XP |
 		     EFI_MEMORY_NV | EFI_MEMORY_SP | EFI_MEMORY_CPU_CRYPTO |
-		     EFI_MEMORY_RUNTIME | EFI_MEMORY_MORE_RELIABLE))
+		     EFI_MEMORY_MORE_RELIABLE | EFI_MEMORY_HOT_PLUGGABLE |
+		     EFI_MEMORY_RUNTIME))
 		snprintf(pos, size, "|attr=0x%016llx]",
 			 (unsigned long long)attr);
 	else
 		snprintf(pos, size,
-			 "|%3s|%2s|%2s|%2s|%2s|%2s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]",
+			 "|%3s|%2s|%2s|%2s|%2s|%2s|%2s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]",
 			 attr & EFI_MEMORY_RUNTIME		? "RUN" : "",
+			 attr & EFI_MEMORY_HOT_PLUGGABLE	? "HP"  : "",
 			 attr & EFI_MEMORY_MORE_RELIABLE	? "MR"  : "",
 			 attr & EFI_MEMORY_CPU_CRYPTO   	? "CC"  : "",
 			 attr & EFI_MEMORY_SP			? "SP"  : "",
@@ -841,40 +854,101 @@
 }
 #endif
 
+struct efi_error_code {
+	efi_status_t status;
+	int errno;
+	const char *description;
+};
+
+static const struct efi_error_code efi_error_codes[] = {
+	{ EFI_SUCCESS, 0, "Success"},
+#if 0
+	{ EFI_LOAD_ERROR, -EPICK_AN_ERRNO, "Load Error"},
+#endif
+	{ EFI_INVALID_PARAMETER, -EINVAL, "Invalid Parameter"},
+	{ EFI_UNSUPPORTED, -ENOSYS, "Unsupported"},
+	{ EFI_BAD_BUFFER_SIZE, -ENOSPC, "Bad Buffer Size"},
+	{ EFI_BUFFER_TOO_SMALL, -ENOSPC, "Buffer Too Small"},
+	{ EFI_NOT_READY, -EAGAIN, "Not Ready"},
+	{ EFI_DEVICE_ERROR, -EIO, "Device Error"},
+	{ EFI_WRITE_PROTECTED, -EROFS, "Write Protected"},
+	{ EFI_OUT_OF_RESOURCES, -ENOMEM, "Out of Resources"},
+#if 0
+	{ EFI_VOLUME_CORRUPTED, -EPICK_AN_ERRNO, "Volume Corrupt"},
+	{ EFI_VOLUME_FULL, -EPICK_AN_ERRNO, "Volume Full"},
+	{ EFI_NO_MEDIA, -EPICK_AN_ERRNO, "No Media"},
+	{ EFI_MEDIA_CHANGED, -EPICK_AN_ERRNO, "Media changed"},
+#endif
+	{ EFI_NOT_FOUND, -ENOENT, "Not Found"},
+#if 0
+	{ EFI_ACCESS_DENIED, -EPICK_AN_ERRNO, "Access Denied"},
+	{ EFI_NO_RESPONSE, -EPICK_AN_ERRNO, "No Response"},
+	{ EFI_NO_MAPPING, -EPICK_AN_ERRNO, "No mapping"},
+	{ EFI_TIMEOUT, -EPICK_AN_ERRNO, "Time out"},
+	{ EFI_NOT_STARTED, -EPICK_AN_ERRNO, "Not started"},
+	{ EFI_ALREADY_STARTED, -EPICK_AN_ERRNO, "Already started"},
+#endif
+	{ EFI_ABORTED, -EINTR, "Aborted"},
+#if 0
+	{ EFI_ICMP_ERROR, -EPICK_AN_ERRNO, "ICMP Error"},
+	{ EFI_TFTP_ERROR, -EPICK_AN_ERRNO, "TFTP Error"},
+	{ EFI_PROTOCOL_ERROR, -EPICK_AN_ERRNO, "Protocol Error"},
+	{ EFI_INCOMPATIBLE_VERSION, -EPICK_AN_ERRNO, "Incompatible Version"},
+#endif
+	{ EFI_SECURITY_VIOLATION, -EACCES, "Security Policy Violation"},
+#if 0
+	{ EFI_CRC_ERROR, -EPICK_AN_ERRNO, "CRC Error"},
+	{ EFI_END_OF_MEDIA, -EPICK_AN_ERRNO, "End of Media"},
+	{ EFI_END_OF_FILE, -EPICK_AN_ERRNO, "End of File"},
+	{ EFI_INVALID_LANGUAGE, -EPICK_AN_ERRNO, "Invalid Languages"},
+	{ EFI_COMPROMISED_DATA, -EPICK_AN_ERRNO, "Compromised Data"},
+
+	// warnings
+	{ EFI_WARN_UNKOWN_GLYPH, -EPICK_AN_ERRNO, "Warning Unknown Glyph"},
+	{ EFI_WARN_DELETE_FAILURE, -EPICK_AN_ERRNO, "Warning Delete Failure"},
+	{ EFI_WARN_WRITE_FAILURE, -EPICK_AN_ERRNO, "Warning Write Failure"},
+	{ EFI_WARN_BUFFER_TOO_SMALL, -EPICK_AN_ERRNO, "Warning Buffer Too Small"},
+#endif
+};
+
+static int
+efi_status_cmp_bsearch(const void *key, const void *item)
+{
+	u64 status = (u64)(uintptr_t)key;
+	struct efi_error_code *code = (struct efi_error_code *)item;
+
+	if (status < code->status)
+		return -1;
+	if (status > code->status)
+		return 1;
+	return 0;
+}
+
 int efi_status_to_err(efi_status_t status)
 {
-	int err;
+	struct efi_error_code *found;
+	size_t num = sizeof(efi_error_codes) / sizeof(struct efi_error_code);
 
-	switch (status) {
-	case EFI_SUCCESS:
-		err = 0;
-		break;
-	case EFI_INVALID_PARAMETER:
-		err = -EINVAL;
-		break;
-	case EFI_OUT_OF_RESOURCES:
-		err = -ENOSPC;
-		break;
-	case EFI_DEVICE_ERROR:
-		err = -EIO;
-		break;
-	case EFI_WRITE_PROTECTED:
-		err = -EROFS;
-		break;
-	case EFI_SECURITY_VIOLATION:
-		err = -EACCES;
-		break;
-	case EFI_NOT_FOUND:
-		err = -ENOENT;
-		break;
-	case EFI_ABORTED:
-		err = -EINTR;
-		break;
-	default:
-		err = -EINVAL;
-	}
+	found = bsearch((void *)(uintptr_t)status, efi_error_codes,
+			sizeof(struct efi_error_code), num,
+			efi_status_cmp_bsearch);
+	if (!found)
+		return -EINVAL;
+	return found->errno;
+}
+
+const char *
+efi_status_to_str(efi_status_t status)
+{
+	struct efi_error_code *found;
+	size_t num = sizeof(efi_error_codes) / sizeof(struct efi_error_code);
 
-	return err;
+	found = bsearch((void *)(uintptr_t)status, efi_error_codes,
+			sizeof(struct efi_error_code), num,
+			efi_status_cmp_bsearch);
+	if (!found)
+		return "Unknown error code";
+	return found->description;
 }
 
 static DEFINE_SPINLOCK(efi_mem_reserve_persistent_lock);
@@ -940,6 +1014,8 @@
 	/* first try to find a slot in an existing linked list entry */
 	for (prsv = efi_memreserve_root->next; prsv; ) {
 		rsv = memremap(prsv, sizeof(*rsv), MEMREMAP_WB);
+		if (!rsv)
+			return -ENOMEM;
 		index = atomic_fetch_add_unless(&rsv->count, 1, rsv->size);
 		if (index < rsv->size) {
 			rsv->entry[index].base = addr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/fdtparams.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/fdtparams.c
@@ -16,25 +16,35 @@
 	MMSIZE,
 	DCSIZE,
 	DCVERS,
+	SCBOOT,
 
 	PARAMCOUNT
 };
 
+static u32 __secure_boot __initdata = efi_secureboot_mode_unset;
+u32 __init efi_get__secure_boot(void)
+{
+	return __secure_boot;
+}
+
 static __initconst const char name[][22] = {
 	[SYSTAB] = "System Table         ",
 	[MMBASE] = "MemMap Address       ",
 	[MMSIZE] = "MemMap Size          ",
 	[DCSIZE] = "MemMap Desc. Size    ",
 	[DCVERS] = "MemMap Desc. Version ",
+	[SCBOOT] = "Secure Boot Enabled  ",
 };
 
 static __initconst const struct {
 	const char	path[17];
+	u8		paravirt;
 	const char	params[PARAMCOUNT][26];
 } dt_params[] = {
 	{
 #ifdef CONFIG_XEN    //  <-------17------>
 		.path = "/hypervisor/uefi",
+		.paravirt = 1,
 		.params = {
 			[SYSTAB] = "xen,uefi-system-table",
 			[MMBASE] = "xen,uefi-mmap-start",
@@ -51,6 +61,7 @@
 			[MMSIZE] = "linux,uefi-mmap-size",
 			[DCSIZE] = "linux,uefi-mmap-desc-size",
 			[DCVERS] = "linux,uefi-mmap-desc-ver",
+			[SCBOOT] = "linux,uefi-secure-boot",
 		}
 	}
 };
@@ -93,6 +104,7 @@
 		[MMSIZE] = { &mm->size,		sizeof(mm->size) },
 		[DCSIZE] = { &mm->desc_size,	sizeof(mm->desc_size) },
 		[DCVERS] = { &mm->desc_version,	sizeof(mm->desc_version) },
+		[SCBOOT] = { &__secure_boot,	sizeof(__secure_boot) },
 	};
 
 	BUILD_BUG_ON(ARRAY_SIZE(target) != ARRAY_SIZE(name));
@@ -121,6 +133,8 @@
 			pr_err("Can't find property '%s' in DT!\n", pname);
 			return 0;
 		}
+		if (dt_params[i].paravirt)
+			set_bit(EFI_PARAVIRT, &efi.flags);
 		return systab;
 	}
 notfound:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/Makefile
@@ -7,7 +7,7 @@
 #
 cflags-$(CONFIG_X86_32)		:= -march=i386
 cflags-$(CONFIG_X86_64)		:= -mcmodel=small
-cflags-$(CONFIG_X86)		+= -m$(BITS) -D__KERNEL__ \
+cflags-$(CONFIG_X86)		+= -m$(BITS) -D__KERNEL__ -std=gnu11 \
 				   -fPIC -fno-strict-aliasing -mno-red-zone \
 				   -mno-mmx -mno-sse -fshort-wchar \
 				   -Wno-pointer-sign \
@@ -37,6 +37,13 @@
 				   $(call cc-option,-fno-addrsig) \
 				   -D__DISABLE_EXPORTS
 
+#
+# struct randomization only makes sense for Linux internal types, which the EFI
+# stub code never touches, so let's turn off struct randomization for the stub
+# altogether
+#
+KBUILD_CFLAGS := $(filter-out $(RANDSTRUCT_CFLAGS), $(KBUILD_CFLAGS))
+
 # remove SCS flags from all objects in this directory
 KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_SCS), $(KBUILD_CFLAGS))
 # disable LTO
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/arm64-stub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/arm64-stub.c
@@ -119,9 +119,9 @@
 	if (image->image_base != _text)
 		efi_err("FIRMWARE BUG: efi_loaded_image_t::image_base has bogus value\n");
 
-	if (!IS_ALIGNED((u64)_text, EFI_KIMG_ALIGN))
-		efi_err("FIRMWARE BUG: kernel image not aligned on %ldk boundary\n",
-			EFI_KIMG_ALIGN >> 10);
+	if (!IS_ALIGNED((u64)_text, SEGMENT_ALIGN))
+		efi_err("FIRMWARE BUG: kernel image not aligned on %dk boundary\n",
+			SEGMENT_ALIGN >> 10);
 
 	kernel_size = _edata - _text;
 	kernel_memsize = kernel_size + (_end - _edata);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/efi-stub-helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/efi-stub-helper.c
@@ -439,8 +439,10 @@
 {
 	efi_status_t status;
 
-	status = efi_get_memory_map(map);
+	if (efi_disable_pci_dma)
+		efi_pci_disable_bridge_busmaster();
 
+	status = efi_get_memory_map(map);
 	if (status != EFI_SUCCESS)
 		goto fail;
 
@@ -448,9 +450,6 @@
 	if (status != EFI_SUCCESS)
 		goto free_map;
 
-	if (efi_disable_pci_dma)
-		efi_pci_disable_bridge_busmaster();
-
 	status = efi_bs_call(exit_boot_services, handle, *map->key_ptr);
 
 	if (status == EFI_INVALID_PARAMETER) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/efistub.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/efistub.h
@@ -155,7 +155,7 @@
  * the EFI memory map. Other related structures, e.g. x86 e820ext, need
  * to factor in this headroom requirement as well.
  */
-#define EFI_MMAP_NR_SLACK_SLOTS	8
+#define EFI_MMAP_NR_SLACK_SLOTS	16
 
 struct efi_boot_memmap {
 	efi_memory_desc_t	**map;
@@ -766,6 +766,8 @@
 efi_status_t efi_random_alloc(unsigned long size, unsigned long align,
 			      unsigned long *addr, unsigned long random_seed);
 
+efi_status_t efi_random_get_seed(void);
+
 efi_status_t check_platform_features(void);
 
 void *get_efi_config_table(efi_guid_t guid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/fdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/fdt.c
@@ -148,6 +148,12 @@
 		}
 	}
 
+	fdt_val32 = cpu_to_fdt32(efi_get_secureboot());
+	status = fdt_setprop(fdt, node, "linux,uefi-secure-boot",
+			     &fdt_val32, sizeof(fdt_val32));
+	if (status)
+		goto fdt_set_fail;
+
 	/* Shrink the FDT back to its minimum size: */
 	fdt_pack(fdt);
 
@@ -280,14 +286,6 @@
 		goto fail;
 	}
 
-	/*
-	 * Now that we have done our final memory allocation (and free)
-	 * we can get the memory map key needed for exit_boot_services().
-	 */
-	status = efi_get_memory_map(&map);
-	if (status != EFI_SUCCESS)
-		goto fail_free_new_fdt;
-
 	status = update_fdt((void *)fdt_addr, fdt_size,
 			    (void *)*new_fdt_addr, MAX_FDT_SIZE, cmdline_ptr,
 			    initrd_addr, initrd_size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/random.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/random.c
@@ -67,22 +67,43 @@
 	efi_guid_t rng_proto = EFI_RNG_PROTOCOL_GUID;
 	efi_guid_t rng_algo_raw = EFI_RNG_ALGORITHM_RAW;
 	efi_guid_t rng_table_guid = LINUX_EFI_RANDOM_SEED_TABLE_GUID;
+	struct linux_efi_random_seed *prev_seed, *seed = NULL;
+	int prev_seed_size = 0, seed_size = EFI_RANDOM_SEED_SIZE;
 	efi_rng_protocol_t *rng = NULL;
-	struct linux_efi_random_seed *seed = NULL;
 	efi_status_t status;
 
 	status = efi_bs_call(locate_protocol, &rng_proto, NULL, (void **)&rng);
 	if (status != EFI_SUCCESS)
 		return status;
 
-	status = efi_bs_call(allocate_pool, EFI_RUNTIME_SERVICES_DATA,
-			     sizeof(*seed) + EFI_RANDOM_SEED_SIZE,
+	/*
+	 * Check whether a seed was provided by a prior boot stage. In that
+	 * case, instead of overwriting it, let's create a new buffer that can
+	 * hold both, and concatenate the existing and the new seeds.
+	 * Note that we should read the seed size with caution, in case the
+	 * table got corrupted in memory somehow.
+	 */
+	prev_seed = get_efi_config_table(LINUX_EFI_RANDOM_SEED_TABLE_GUID);
+	if (prev_seed && prev_seed->size <= 512U) {
+		prev_seed_size = prev_seed->size;
+		seed_size += prev_seed_size;
+	}
+
+	/*
+	 * Use EFI_ACPI_RECLAIM_MEMORY here so that it is guaranteed that the
+	 * allocation will survive a kexec reboot (although we refresh the seed
+	 * beforehand)
+	 */
+	status = efi_bs_call(allocate_pool, EFI_ACPI_RECLAIM_MEMORY,
+			     struct_size(seed, bits, seed_size),
 			     (void **)&seed);
-	if (status != EFI_SUCCESS)
-		return status;
+	if (status != EFI_SUCCESS) {
+		efi_warn("Failed to allocate memory for RNG seed.\n");
+		goto err_warn;
+	}
 
 	status = efi_call_proto(rng, get_rng, &rng_algo_raw,
-				 EFI_RANDOM_SEED_SIZE, seed->bits);
+				EFI_RANDOM_SEED_SIZE, seed->bits);
 
 	if (status == EFI_UNSUPPORTED)
 		/*
@@ -95,14 +116,28 @@
 	if (status != EFI_SUCCESS)
 		goto err_freepool;
 
-	seed->size = EFI_RANDOM_SEED_SIZE;
+	seed->size = seed_size;
+	if (prev_seed_size)
+		memcpy(seed->bits + EFI_RANDOM_SEED_SIZE, prev_seed->bits,
+		       prev_seed_size);
+
 	status = efi_bs_call(install_configuration_table, &rng_table_guid, seed);
 	if (status != EFI_SUCCESS)
 		goto err_freepool;
 
+	if (prev_seed_size) {
+		/* wipe and free the old seed if we managed to install the new one */
+		memzero_explicit(prev_seed->bits, prev_seed_size);
+		efi_bs_call(free_pool, prev_seed);
+	}
 	return EFI_SUCCESS;
 
 err_freepool:
+	memzero_explicit(seed, struct_size(seed, bits, seed_size));
 	efi_bs_call(free_pool, seed);
+	efi_warn("Failed to obtain seed from EFI_RNG_PROTOCOL\n");
+err_warn:
+	if (prev_seed)
+		efi_warn("Retaining bootloader-supplied seed only");
 	return status;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/randomalloc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/randomalloc.c
@@ -24,6 +24,9 @@
 	if (md->type != EFI_CONVENTIONAL_MEMORY)
 		return 0;
 
+	if (md->attribute & EFI_MEMORY_HOT_PLUGGABLE)
+		return 0;
+
 	if (efi_soft_reserve_enabled() &&
 	    (md->attribute & EFI_MEMORY_SP))
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/relocate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/relocate.c
@@ -62,6 +62,9 @@
 		if (desc->type != EFI_CONVENTIONAL_MEMORY)
 			continue;
 
+		if (desc->attribute & EFI_MEMORY_HOT_PLUGGABLE)
+			continue;
+
 		if (efi_soft_reserve_enabled() &&
 		    (desc->attribute & EFI_MEMORY_SP))
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/riscv-stub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/riscv-stub.c
@@ -25,7 +25,7 @@
 
 static u32 hartid;
 
-static u32 get_boot_hartid_from_fdt(void)
+static int get_boot_hartid_from_fdt(void)
 {
 	const void *fdt;
 	int chosen_node, len;
@@ -33,23 +33,26 @@
 
 	fdt = get_efi_config_table(DEVICE_TREE_GUID);
 	if (!fdt)
-		return U32_MAX;
+		return -EINVAL;
 
 	chosen_node = fdt_path_offset(fdt, "/chosen");
 	if (chosen_node < 0)
-		return U32_MAX;
+		return -EINVAL;
 
 	prop = fdt_getprop((void *)fdt, chosen_node, "boot-hartid", &len);
 	if (!prop || len != sizeof(u32))
-		return U32_MAX;
+		return -EINVAL;
 
-	return fdt32_to_cpu(*prop);
+	hartid = fdt32_to_cpu(*prop);
+	return 0;
 }
 
 efi_status_t check_platform_features(void)
 {
-	hartid = get_boot_hartid_from_fdt();
-	if (hartid == U32_MAX) {
+	int ret;
+
+	ret = get_boot_hartid_from_fdt();
+	if (ret) {
 		efi_err("/chosen/boot-hartid missing or invalid!\n");
 		return EFI_UNSUPPORTED;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/secureboot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/secureboot.c
@@ -14,7 +14,7 @@
 
 /* SHIM variables */
 static const efi_guid_t shim_guid = EFI_SHIM_LOCK_GUID;
-static const efi_char16_t shim_MokSBState_name[] = L"MokSBState";
+static const efi_char16_t shim_MokSBState_name[] = L"MokSBStateRT";
 
 static efi_status_t get_var(efi_char16_t *name, efi_guid_t *vendor, u32 *attr,
 			    unsigned long *data_size, void *data)
@@ -43,8 +43,8 @@
 
 	/*
 	 * See if a user has put the shim into insecure mode. If so, and if the
-	 * variable doesn't have the runtime attribute set, we might as well
-	 * honor that.
+	 * variable doesn't have the non-volatile attribute set, we might as
+	 * well honor that.
 	 */
 	size = sizeof(moksbstate);
 	status = get_efi_var(shim_MokSBState_name, &shim_guid,
@@ -53,7 +53,7 @@
 	/* If it fails, we don't care why. Default to secure */
 	if (status != EFI_SUCCESS)
 		goto secure_boot_enabled;
-	if (!(attr & EFI_VARIABLE_RUNTIME_ACCESS) && moksbstate == 1)
+	if (!(attr & EFI_VARIABLE_NON_VOLATILE) && moksbstate == 1)
 		return efi_secureboot_mode_disabled;
 
 secure_boot_enabled:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/tpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/tpm.c
@@ -115,7 +115,7 @@
 	}
 
 	/* Allocate space for the logs and copy them. */
-	status = efi_bs_call(allocate_pool, EFI_LOADER_DATA,
+	status = efi_bs_call(allocate_pool, EFI_ACPI_RECLAIM_MEMORY,
 			     sizeof(*log_tbl) + log_size, (void **)&log_tbl);
 
 	if (status != EFI_SUCCESS) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/libstub/x86-stub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/libstub/x86-stub.c
@@ -60,7 +60,7 @@
 	rom->data.type	= SETUP_PCI;
 	rom->data.len	= size - sizeof(struct setup_data);
 	rom->data.next	= 0;
-	rom->pcilen	= pci->romsize;
+	rom->pcilen	= romsize;
 	*__rom = rom;
 
 	status = efi_call_proto(pci, pci.read, EfiPciIoWidthUint16,
@@ -414,6 +414,13 @@
 	hdr->ramdisk_image = 0;
 	hdr->ramdisk_size = 0;
 
+	/*
+	 * Disregard any setup data that was provided by the bootloader:
+	 * setup_data could be pointing anywhere, and we have no way of
+	 * authenticating or validating the payload.
+	 */
+	hdr->setup_data = 0;
+
 	efi_stub_entry(handle, sys_table_arg, boot_params);
 	/* not reached */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/memattr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/memattr.c
@@ -33,7 +33,7 @@
 		return -ENOMEM;
 	}
 
-	if (tbl->version > 1) {
+	if (tbl->version > 2) {
 		pr_warn("Unexpected EFI Memory Attributes table version %d\n",
 			tbl->version);
 		goto unmap;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/memmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/memmap.c
@@ -9,83 +9,11 @@
 #include <linux/kernel.h>
 #include <linux/efi.h>
 #include <linux/io.h>
-#include <asm/early_ioremap.h>
 #include <linux/memblock.h>
 #include <linux/slab.h>
 
-static phys_addr_t __init __efi_memmap_alloc_early(unsigned long size)
-{
-	return memblock_phys_alloc(size, SMP_CACHE_BYTES);
-}
-
-static phys_addr_t __init __efi_memmap_alloc_late(unsigned long size)
-{
-	unsigned int order = get_order(size);
-	struct page *p = alloc_pages(GFP_KERNEL, order);
-
-	if (!p)
-		return 0;
-
-	return PFN_PHYS(page_to_pfn(p));
-}
-
-void __init __efi_memmap_free(u64 phys, unsigned long size, unsigned long flags)
-{
-	if (flags & EFI_MEMMAP_MEMBLOCK) {
-		if (slab_is_available())
-			memblock_free_late(phys, size);
-		else
-			memblock_free(phys, size);
-	} else if (flags & EFI_MEMMAP_SLAB) {
-		struct page *p = pfn_to_page(PHYS_PFN(phys));
-		unsigned int order = get_order(size);
-
-		free_pages((unsigned long) page_address(p), order);
-	}
-}
-
-static void __init efi_memmap_free(void)
-{
-	__efi_memmap_free(efi.memmap.phys_map,
-			efi.memmap.desc_size * efi.memmap.nr_map,
-			efi.memmap.flags);
-}
-
-/**
- * efi_memmap_alloc - Allocate memory for the EFI memory map
- * @num_entries: Number of entries in the allocated map.
- * @data: efi memmap installation parameters
- *
- * Depending on whether mm_init() has already been invoked or not,
- * either memblock or "normal" page allocation is used.
- *
- * Returns the physical address of the allocated memory map on
- * success, zero on failure.
- */
-int __init efi_memmap_alloc(unsigned int num_entries,
-		struct efi_memory_map_data *data)
-{
-	/* Expect allocation parameters are zero initialized */
-	WARN_ON(data->phys_map || data->size);
-
-	data->size = num_entries * efi.memmap.desc_size;
-	data->desc_version = efi.memmap.desc_version;
-	data->desc_size = efi.memmap.desc_size;
-	data->flags &= ~(EFI_MEMMAP_SLAB | EFI_MEMMAP_MEMBLOCK);
-	data->flags |= efi.memmap.flags & EFI_MEMMAP_LATE;
-
-	if (slab_is_available()) {
-		data->flags |= EFI_MEMMAP_SLAB;
-		data->phys_map = __efi_memmap_alloc_late(data->size);
-	} else {
-		data->flags |= EFI_MEMMAP_MEMBLOCK;
-		data->phys_map = __efi_memmap_alloc_early(data->size);
-	}
-
-	if (!data->phys_map)
-		return -ENOMEM;
-	return 0;
-}
+#include <asm/early_ioremap.h>
+#include <asm/efi.h>
 
 /**
  * __efi_memmap_init - Common code for mapping the EFI memory map
@@ -102,14 +30,11 @@
  *
  * Returns zero on success, a negative error code on failure.
  */
-static int __init __efi_memmap_init(struct efi_memory_map_data *data)
+int __init __efi_memmap_init(struct efi_memory_map_data *data)
 {
 	struct efi_memory_map map;
 	phys_addr_t phys_map;
 
-	if (efi_enabled(EFI_PARAVIRT))
-		return 0;
-
 	phys_map = data->phys_map;
 
 	if (data->flags & EFI_MEMMAP_LATE)
@@ -122,9 +47,6 @@
 		return -ENOMEM;
 	}
 
-	/* NOP if data->flags & (EFI_MEMMAP_MEMBLOCK | EFI_MEMMAP_SLAB) == 0 */
-	efi_memmap_free();
-
 	map.phys_map = data->phys_map;
 	map.nr_map = data->size / data->desc_size;
 	map.map_end = map.map + data->size;
@@ -221,158 +143,3 @@
 
 	return __efi_memmap_init(&data);
 }
-
-/**
- * efi_memmap_install - Install a new EFI memory map in efi.memmap
- * @ctx: map allocation parameters (address, size, flags)
- *
- * Unlike efi_memmap_init_*(), this function does not allow the caller
- * to switch from early to late mappings. It simply uses the existing
- * mapping function and installs the new memmap.
- *
- * Returns zero on success, a negative error code on failure.
- */
-int __init efi_memmap_install(struct efi_memory_map_data *data)
-{
-	efi_memmap_unmap();
-
-	return __efi_memmap_init(data);
-}
-
-/**
- * efi_memmap_split_count - Count number of additional EFI memmap entries
- * @md: EFI memory descriptor to split
- * @range: Address range (start, end) to split around
- *
- * Returns the number of additional EFI memmap entries required to
- * accomodate @range.
- */
-int __init efi_memmap_split_count(efi_memory_desc_t *md, struct range *range)
-{
-	u64 m_start, m_end;
-	u64 start, end;
-	int count = 0;
-
-	start = md->phys_addr;
-	end = start + (md->num_pages << EFI_PAGE_SHIFT) - 1;
-
-	/* modifying range */
-	m_start = range->start;
-	m_end = range->end;
-
-	if (m_start <= start) {
-		/* split into 2 parts */
-		if (start < m_end && m_end < end)
-			count++;
-	}
-
-	if (start < m_start && m_start < end) {
-		/* split into 3 parts */
-		if (m_end < end)
-			count += 2;
-		/* split into 2 parts */
-		if (end <= m_end)
-			count++;
-	}
-
-	return count;
-}
-
-/**
- * efi_memmap_insert - Insert a memory region in an EFI memmap
- * @old_memmap: The existing EFI memory map structure
- * @buf: Address of buffer to store new map
- * @mem: Memory map entry to insert
- *
- * It is suggested that you call efi_memmap_split_count() first
- * to see how large @buf needs to be.
- */
-void __init efi_memmap_insert(struct efi_memory_map *old_memmap, void *buf,
-			      struct efi_mem_range *mem)
-{
-	u64 m_start, m_end, m_attr;
-	efi_memory_desc_t *md;
-	u64 start, end;
-	void *old, *new;
-
-	/* modifying range */
-	m_start = mem->range.start;
-	m_end = mem->range.end;
-	m_attr = mem->attribute;
-
-	/*
-	 * The EFI memory map deals with regions in EFI_PAGE_SIZE
-	 * units. Ensure that the region described by 'mem' is aligned
-	 * correctly.
-	 */
-	if (!IS_ALIGNED(m_start, EFI_PAGE_SIZE) ||
-	    !IS_ALIGNED(m_end + 1, EFI_PAGE_SIZE)) {
-		WARN_ON(1);
-		return;
-	}
-
-	for (old = old_memmap->map, new = buf;
-	     old < old_memmap->map_end;
-	     old += old_memmap->desc_size, new += old_memmap->desc_size) {
-
-		/* copy original EFI memory descriptor */
-		memcpy(new, old, old_memmap->desc_size);
-		md = new;
-		start = md->phys_addr;
-		end = md->phys_addr + (md->num_pages << EFI_PAGE_SHIFT) - 1;
-
-		if (m_start <= start && end <= m_end)
-			md->attribute |= m_attr;
-
-		if (m_start <= start &&
-		    (start < m_end && m_end < end)) {
-			/* first part */
-			md->attribute |= m_attr;
-			md->num_pages = (m_end - md->phys_addr + 1) >>
-				EFI_PAGE_SHIFT;
-			/* latter part */
-			new += old_memmap->desc_size;
-			memcpy(new, old, old_memmap->desc_size);
-			md = new;
-			md->phys_addr = m_end + 1;
-			md->num_pages = (end - md->phys_addr + 1) >>
-				EFI_PAGE_SHIFT;
-		}
-
-		if ((start < m_start && m_start < end) && m_end < end) {
-			/* first part */
-			md->num_pages = (m_start - md->phys_addr) >>
-				EFI_PAGE_SHIFT;
-			/* middle part */
-			new += old_memmap->desc_size;
-			memcpy(new, old, old_memmap->desc_size);
-			md = new;
-			md->attribute |= m_attr;
-			md->phys_addr = m_start;
-			md->num_pages = (m_end - m_start + 1) >>
-				EFI_PAGE_SHIFT;
-			/* last part */
-			new += old_memmap->desc_size;
-			memcpy(new, old, old_memmap->desc_size);
-			md = new;
-			md->phys_addr = m_end + 1;
-			md->num_pages = (end - m_end) >>
-				EFI_PAGE_SHIFT;
-		}
-
-		if ((start < m_start && m_start < end) &&
-		    (end <= m_end)) {
-			/* first part */
-			md->num_pages = (m_start - md->phys_addr) >>
-				EFI_PAGE_SHIFT;
-			/* latter part */
-			new += old_memmap->desc_size;
-			memcpy(new, old, old_memmap->desc_size);
-			md = new;
-			md->phys_addr = m_start;
-			md->num_pages = (end - md->phys_addr + 1) >>
-				EFI_PAGE_SHIFT;
-			md->attribute |= m_attr;
-		}
-	}
-}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/riscv-runtime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/riscv-runtime.c
@@ -85,7 +85,7 @@
 		efi_memory_desc_t *md;
 
 		for_each_efi_memory_desc(md) {
-			int md_size = md->num_pages << EFI_PAGE_SHIFT;
+			u64 md_size = md->num_pages << EFI_PAGE_SHIFT;
 			struct resource *res;
 
 			if (!(md->attribute & EFI_MEMORY_SP))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/runtime-wrappers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/runtime-wrappers.c
@@ -62,6 +62,7 @@
 									\
 	if (!efi_enabled(EFI_RUNTIME_SERVICES)) {			\
 		pr_warn_once("EFI Runtime Services are disabled!\n");	\
+		efi_rts_work.status = EFI_DEVICE_ERROR;			\
 		goto exit;						\
 	}								\
 									\
@@ -83,6 +84,7 @@
 	else								\
 		pr_err("Failed to queue work to efi_rts_wq.\n");	\
 									\
+	WARN_ON_ONCE(efi_rts_work.status == EFI_ABORTED);		\
 exit:									\
 	efi_rts_work.efi_rts_id = EFI_NONE;				\
 	efi_rts_work.status;						\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/secureboot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/secureboot.c
@@ -0,0 +1,38 @@
+/* Core kernel secure boot support.
+ *
+ * Copyright (C) 2017 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public Licence
+ * as published by the Free Software Foundation; either version
+ * 2 of the Licence, or (at your option) any later version.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/efi.h>
+#include <linux/kernel.h>
+#include <linux/printk.h>
+
+/*
+ * Decide what to do when UEFI secure boot mode is enabled.
+ */
+void __init efi_set_secure_boot(enum efi_secureboot_mode mode)
+{
+	if (efi_enabled(EFI_BOOT)) {
+		switch (mode) {
+		case efi_secureboot_mode_disabled:
+			pr_info("Secure boot disabled\n");
+			break;
+		case efi_secureboot_mode_enabled:
+			set_bit(EFI_SECURE_BOOT, &efi.flags);
+			pr_info("Secure boot enabled\n");
+			break;
+		default:
+			pr_warn("Secure boot could not be determined (mode %u)\n",
+				   mode);
+			break;
+		}
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/sysfb_efi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/sysfb_efi.c
@@ -93,6 +93,7 @@
 		_ret_;						\
 	})
 
+#ifdef CONFIG_EFI
 static int __init efifb_set_system(const struct dmi_system_id *id)
 {
 	struct efifb_dmi_info *info = id->driver_data;
@@ -266,6 +267,22 @@
 					"Lenovo ideapad D330-10IGM"),
 		},
 	},
+	{
+		/* Lenovo IdeaPad Duet 3 10IGL5 with 1200x1920 portrait screen */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_VERSION,
+					"IdeaPad Duet 3 10IGL5"),
+		},
+	},
+	{
+		/* Lenovo Yoga Book X91F / X91L */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			/* Non exact match to match F + L versions */
+			DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X91"),
+		},
+	},
 	{},
 };
 
@@ -332,10 +349,9 @@
 	.add_links = efifb_add_links,
 };
 
-#ifdef CONFIG_EFI
 static struct fwnode_handle efifb_fwnode;
 
-__init void sysfb_apply_efi_quirks(struct platform_device *pd)
+__init void sysfb_apply_efi_quirks(void)
 {
 	if (screen_info.orig_video_isVGA != VIDEO_TYPE_EFI ||
 	    !(screen_info.capabilities & VIDEO_CAPABILITY_SKIP_QUIRKS))
@@ -349,7 +365,10 @@
 		screen_info.lfb_height = temp;
 		screen_info.lfb_linelength = 4 * screen_info.lfb_width;
 	}
+}
 
+__init void sysfb_set_efifb_fwnode(struct platform_device *pd)
+{
 	if (screen_info.orig_video_isVGA == VIDEO_TYPE_EFI && IS_ENABLED(CONFIG_PCI)) {
 		fwnode_init(&efifb_fwnode, &efifb_fwnode_ops);
 		pd->dev.fwnode = &efifb_fwnode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/tpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/tpm.c
@@ -40,7 +40,8 @@
 {
 	struct linux_efi_tpm_eventlog *log_tbl;
 	struct efi_tcg2_final_events_table *final_tbl;
-	int tbl_size;
+	unsigned int tbl_size;
+	int final_tbl_size;
 	int ret = 0;
 
 	if (efi.tpm_log == EFI_INVALID_TABLE_ADDR) {
@@ -80,26 +81,26 @@
 		goto out;
 	}
 
-	tbl_size = 0;
+	final_tbl_size = 0;
 	if (final_tbl->nr_events != 0) {
 		void *events = (void *)efi.tpm_final_log
 				+ sizeof(final_tbl->version)
 				+ sizeof(final_tbl->nr_events);
 
-		tbl_size = tpm2_calc_event_log_size(events,
-						    final_tbl->nr_events,
-						    log_tbl->log);
+		final_tbl_size = tpm2_calc_event_log_size(events,
+							  final_tbl->nr_events,
+							  log_tbl->log);
 	}
 
-	if (tbl_size < 0) {
+	if (final_tbl_size < 0) {
 		pr_err(FW_BUG "Failed to parse event in TPM Final Events Log\n");
 		ret = -EINVAL;
 		goto out_calc;
 	}
 
-	memblock_reserve((unsigned long)final_tbl,
-			 tbl_size + sizeof(*final_tbl));
-	efi_tpm_final_log_size = tbl_size;
+	memblock_reserve(efi.tpm_final_log,
+			 final_tbl_size + sizeof(*final_tbl));
+	efi_tpm_final_log_size = final_tbl_size;
 
 out_calc:
 	early_memunmap(final_tbl, sizeof(*final_tbl));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/efi/vars.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/efi/vars.c
@@ -415,7 +415,7 @@
 		void *data, bool duplicates, struct list_head *head)
 {
 	const struct efivar_operations *ops;
-	unsigned long variable_name_size = 1024;
+	unsigned long variable_name_size = 512;
 	efi_char16_t *variable_name;
 	efi_status_t status;
 	efi_guid_t vendor_guid;
@@ -438,12 +438,13 @@
 	}
 
 	/*
-	 * Per EFI spec, the maximum storage allocated for both
-	 * the variable name and variable data is 1024 bytes.
+	 * A small set of old UEFI implementations reject sizes
+	 * above a certain threshold, the lowest seen in the wild
+	 * is 512.
 	 */
 
 	do {
-		variable_name_size = 1024;
+		variable_name_size = 512;
 
 		status = ops->get_next_variable(&variable_name_size,
 						variable_name,
@@ -491,9 +492,13 @@
 			break;
 		case EFI_NOT_FOUND:
 			break;
+		case EFI_BUFFER_TOO_SMALL:
+			pr_warn("efivars: Variable name size exceeds maximum (%lu > 512)\n",
+				variable_name_size);
+			status = EFI_NOT_FOUND;
+			break;
 		default:
-			printk(KERN_WARNING "efivars: get_next_variable: status=%lx\n",
-				status);
+			pr_warn("efivars: get_next_variable: status=%lx\n", status);
 			status = EFI_NOT_FOUND;
 			break;
 		}
@@ -742,6 +747,7 @@
 {
 	const struct efivar_operations *ops;
 	efi_status_t status;
+	unsigned long varsize;
 
 	if (!__efivars)
 		return -EINVAL;
@@ -764,15 +770,17 @@
 		return efivar_entry_set_nonblocking(name, vendor, attributes,
 						    size, data);
 
+	varsize = size + ucs2_strsize(name, 1024);
 	if (!block) {
 		if (down_trylock(&efivars_lock))
 			return -EBUSY;
+		status = check_var_size_nonblocking(attributes, varsize);
 	} else {
 		if (down_interruptible(&efivars_lock))
 			return -EINTR;
+		status = check_var_size(attributes, varsize);
 	}
 
-	status = check_var_size(attributes, size + ucs2_strsize(name, 1024));
 	if (status != EFI_SUCCESS) {
 		up(&efivars_lock);
 		return -ENOSPC;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/google/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/google/Kconfig
@@ -3,9 +3,9 @@
 	bool "Google Firmware Drivers"
 	default n
 	help
-	  These firmware drivers are used by Google's servers.  They are
-	  only useful if you are working directly on one of their
-	  proprietary servers.  If in doubt, say "N".
+	  These firmware drivers are used by Google servers,
+	  Chromebooks and other devices using coreboot firmware.
+	  If in doubt, say "N".
 
 if GOOGLE_FIRMWARE
 
@@ -21,7 +21,7 @@
 
 config GOOGLE_COREBOOT_TABLE
 	tristate "Coreboot Table Access"
-	depends on ACPI || OF
+	depends on HAS_IOMEM && (ACPI || OF)
 	help
 	  This option enables the coreboot_table module, which provides other
 	  firmware modules access to the coreboot table. The coreboot table
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/google/coreboot_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/google/coreboot_table.c
@@ -93,7 +93,12 @@
 	for (i = 0; i < header->table_entries; i++) {
 		entry = ptr_entry;
 
-		device = kzalloc(sizeof(struct device) + entry->size, GFP_KERNEL);
+		if (entry->size < sizeof(*entry)) {
+			dev_warn(dev, "coreboot table entry too small!\n");
+			return -EINVAL;
+		}
+
+		device = kzalloc(sizeof(device->dev) + entry->size, GFP_KERNEL);
 		if (!device)
 			return -ENOMEM;
 
@@ -101,7 +106,7 @@
 		device->dev.parent = dev;
 		device->dev.bus = &coreboot_bus_type;
 		device->dev.release = coreboot_device_release;
-		memcpy(&device->entry, ptr_entry, entry->size);
+		memcpy(device->raw, ptr_entry, entry->size);
 
 		ret = device_register(&device->dev);
 		if (ret) {
@@ -149,12 +154,8 @@
 	if (!ptr)
 		return -ENOMEM;
 
-	ret = bus_register(&coreboot_bus_type);
-	if (!ret) {
-		ret = coreboot_table_populate(dev, ptr);
-		if (ret)
-			bus_unregister(&coreboot_bus_type);
-	}
+	ret = coreboot_table_populate(dev, ptr);
+
 	memunmap(ptr);
 
 	return ret;
@@ -169,7 +170,6 @@
 static int coreboot_table_remove(struct platform_device *pdev)
 {
 	bus_for_each_dev(&coreboot_bus_type, NULL, NULL, __cb_dev_unregister);
-	bus_unregister(&coreboot_bus_type);
 	return 0;
 }
 
@@ -199,6 +199,32 @@
 		.of_match_table = of_match_ptr(coreboot_of_match),
 	},
 };
-module_platform_driver(coreboot_table_driver);
+
+static int __init coreboot_table_driver_init(void)
+{
+	int ret;
+
+	ret = bus_register(&coreboot_bus_type);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&coreboot_table_driver);
+	if (ret) {
+		bus_unregister(&coreboot_bus_type);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit coreboot_table_driver_exit(void)
+{
+	platform_driver_unregister(&coreboot_table_driver);
+	bus_unregister(&coreboot_bus_type);
+}
+
+module_init(coreboot_table_driver_init);
+module_exit(coreboot_table_driver_exit);
+
 MODULE_AUTHOR("Google, Inc.");
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/google/coreboot_table.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/google/coreboot_table.h
@@ -66,6 +66,7 @@
 		struct coreboot_table_entry entry;
 		struct lb_cbmem_ref cbmem_ref;
 		struct lb_framebuffer framebuffer;
+		DECLARE_FLEX_ARRAY(u8, raw);
 	};
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/google/framebuffer-coreboot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/google/framebuffer-coreboot.c
@@ -43,9 +43,7 @@
 		    fb->green_mask_pos     == formats[i].green.offset &&
 		    fb->green_mask_size    == formats[i].green.length &&
 		    fb->blue_mask_pos      == formats[i].blue.offset &&
-		    fb->blue_mask_size     == formats[i].blue.length &&
-		    fb->reserved_mask_pos  == formats[i].transp.offset &&
-		    fb->reserved_mask_size == formats[i].transp.length)
+		    fb->blue_mask_size     == formats[i].blue.length)
 			pdata.format = formats[i].name;
 	}
 	if (!pdata.format)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/google/gsmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/google/gsmi.c
@@ -361,9 +361,10 @@
 		memcpy(data, gsmi_dev.data_buf->start, *data_size);
 
 		/* All variables are have the following attributes */
-		*attr = EFI_VARIABLE_NON_VOLATILE |
-			EFI_VARIABLE_BOOTSERVICE_ACCESS |
-			EFI_VARIABLE_RUNTIME_ACCESS;
+		if (attr)
+			*attr = EFI_VARIABLE_NON_VOLATILE |
+				EFI_VARIABLE_BOOTSERVICE_ACCESS |
+				EFI_VARIABLE_RUNTIME_ACCESS;
 	}
 
 	spin_unlock_irqrestore(&gsmi_dev.lock, flags);
@@ -681,6 +682,15 @@
 static int gsmi_panic_callback(struct notifier_block *nb,
 			       unsigned long reason, void *arg)
 {
+
+	/*
+	 * Panic callbacks are executed with all other CPUs stopped,
+	 * so we must not attempt to spin waiting for gsmi_dev.lock
+	 * to be released.
+	 */
+	if (spin_is_locked(&gsmi_dev.lock))
+		return NOTIFY_DONE;
+
 	gsmi_shutdown_reason(GSMI_SHUTDOWN_PANIC);
 	return NOTIFY_DONE;
 }
@@ -908,7 +918,8 @@
 	gsmi_dev.pdev = platform_device_register_full(&gsmi_dev_info);
 	if (IS_ERR(gsmi_dev.pdev)) {
 		printk(KERN_ERR "gsmi: unable to register platform device\n");
-		return PTR_ERR(gsmi_dev.pdev);
+		ret = PTR_ERR(gsmi_dev.pdev);
+		goto out_unregister;
 	}
 
 	/* SMI access needs to be serialized */
@@ -1046,10 +1057,11 @@
 	gsmi_buf_free(gsmi_dev.name_buf);
 	kmem_cache_destroy(gsmi_dev.mem_pool);
 	platform_device_unregister(gsmi_dev.pdev);
-	pr_info("gsmi: failed to load: %d\n", ret);
+out_unregister:
 #ifdef CONFIG_PM
 	platform_driver_unregister(&gsmi_driver_info);
 #endif
+	pr_info("gsmi: failed to load: %d\n", ret);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/imx/imx-dsp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/imx/imx-dsp.c
@@ -119,6 +119,7 @@
 			if (ret != -EPROBE_DEFER)
 				dev_err(dev, "Failed to request mbox chan %s ret %d\n",
 					chan_name, ret);
+			kfree(dsp_chan->name);
 			goto out;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/imx/imx-scu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/imx/imx-scu.c
@@ -279,6 +279,7 @@
 		return ret;
 
 	sc_ipc->fast_ipc = of_device_is_compatible(args.np, "fsl,imx8-mu-scu");
+	of_node_put(args.np);
 
 	num_channel = sc_ipc->fast_ipc ? 2 : SCU_MU_CHAN_NUM;
 	for (i = 0; i < num_channel; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/iscsi_ibft.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/iscsi_ibft.c
@@ -310,7 +310,10 @@
 		str += sprintf_ipaddr(str, nic->ip_addr);
 		break;
 	case ISCSI_BOOT_ETH_SUBNET_MASK:
-		val = cpu_to_be32(~((1 << (32-nic->subnet_mask_prefix))-1));
+		if (nic->subnet_mask_prefix > 32)
+			val = cpu_to_be32(~0);
+		else
+			val = cpu_to_be32(~((1 << (32-nic->subnet_mask_prefix))-1));
 		str += sprintf(str, "%pI4", &val);
 		break;
 	case ISCSI_BOOT_ETH_PREFIX_LEN:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/meson/meson_sm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/meson/meson_sm.c
@@ -292,6 +292,8 @@
 		return -ENOMEM;
 
 	chip = of_match_device(meson_sm_ids, dev)->data;
+	if (!chip)
+		return -EINVAL;
 
 	if (chip->cmd_shmem_in_base) {
 		fw->sm_shmem_in_base = meson_sm_map_shmem(chip->cmd_shmem_in_base,
@@ -311,11 +313,14 @@
 
 	platform_set_drvdata(pdev, fw);
 
-	pr_info("secure-monitor enabled\n");
+	if (devm_of_platform_populate(dev))
+		goto out_in_base;
 
 	if (sysfs_create_group(&pdev->dev.kobj, &meson_sm_sysfs_attr_group))
 		goto out_in_base;
 
+	pr_info("secure-monitor enabled\n");
+
 	return 0;
 
 out_in_base:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/psci/psci_checker.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/psci/psci_checker.c
@@ -155,7 +155,7 @@
 	if (!alloc_cpumask_var(&tmp, GFP_KERNEL))
 		return -ENOMEM;
 
-	cpu_groups = kcalloc(nb_available_cpus, sizeof(cpu_groups),
+	cpu_groups = kcalloc(nb_available_cpus, sizeof(*cpu_groups),
 			     GFP_KERNEL);
 	if (!cpu_groups) {
 		free_cpumask_var(tmp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/qcom_scm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/qcom_scm.c
@@ -137,6 +137,12 @@
 		return qcom_scm_convention;
 
 	/*
+	 * Per the "SMC calling convention specification", the 64-bit calling
+	 * convention can only be used when the client is 64-bit, otherwise
+	 * system will encounter the undefined behaviour.
+	 */
+#if IS_ENABLED(CONFIG_ARM64)
+	/*
 	 * Device isn't required as there is only one argument - no device
 	 * needed to dma_map_single to secure world
 	 */
@@ -156,6 +162,7 @@
 		forced = true;
 		goto found;
 	}
+#endif
 
 	probed_convention = SMC_CONVENTION_ARM_32;
 	ret = __scm_smc_call(NULL, &desc, probed_convention, &res, true);
@@ -252,7 +259,7 @@
 		break;
 	default:
 		pr_err("Unknown SMC convention being used\n");
-		return -EINVAL;
+		return false;
 	}
 
 	ret = qcom_scm_call(dev, &desc, &res);
@@ -749,12 +756,6 @@
 	};
 	int ret;
 
-	desc.args[0] = addr;
-	desc.args[1] = size;
-	desc.args[2] = spare;
-	desc.arginfo = QCOM_SCM_ARGS(3, QCOM_SCM_RW, QCOM_SCM_VAL,
-				     QCOM_SCM_VAL);
-
 	ret = qcom_scm_call(__scm->dev, &desc, NULL);
 
 	/* the pg table has been initialized already, ignore the error */
@@ -1326,8 +1327,7 @@
 static void qcom_scm_shutdown(struct platform_device *pdev)
 {
 	/* Clean shutdown, disable download mode to allow normal restart */
-	if (download_mode)
-		qcom_scm_set_download_mode(false);
+	qcom_scm_set_download_mode(false);
 }
 
 static const struct of_device_id qcom_scm_dt_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/qemu_fw_cfg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/qemu_fw_cfg.c
@@ -388,9 +388,7 @@
 	struct fw_cfg_sysfs_entry *entry, *next;
 
 	list_for_each_entry_safe(entry, next, &fw_cfg_entry_cache, list) {
-		/* will end up invoking fw_cfg_sysfs_cache_delist()
-		 * via each object's release() method (i.e. destructor)
-		 */
+		fw_cfg_sysfs_cache_delist(entry);
 		kobject_put(&entry->kobj);
 	}
 }
@@ -448,7 +446,6 @@
 {
 	struct fw_cfg_sysfs_entry *entry = to_entry(kobj);
 
-	fw_cfg_sysfs_cache_delist(entry);
 	kfree(entry);
 }
 
@@ -601,20 +598,18 @@
 	/* set file entry information */
 	entry->size = be32_to_cpu(f->size);
 	entry->select = be16_to_cpu(f->select);
-	memcpy(entry->name, f->name, FW_CFG_MAX_FILE_PATH);
+	strscpy(entry->name, f->name, FW_CFG_MAX_FILE_PATH);
 
 	/* register entry under "/sys/firmware/qemu_fw_cfg/by_key/" */
 	err = kobject_init_and_add(&entry->kobj, &fw_cfg_sysfs_entry_ktype,
 				   fw_cfg_sel_ko, "%d", entry->select);
-	if (err) {
-		kobject_put(&entry->kobj);
-		return err;
-	}
+	if (err)
+		goto err_put_entry;
 
 	/* add raw binary content access */
 	err = sysfs_create_bin_file(&entry->kobj, &fw_cfg_sysfs_attr_raw);
 	if (err)
-		goto err_add_raw;
+		goto err_del_entry;
 
 	/* try adding "/sys/firmware/qemu_fw_cfg/by_name/" symlink */
 	fw_cfg_build_symlink(fw_cfg_fname_kset, &entry->kobj, entry->name);
@@ -623,9 +618,10 @@
 	fw_cfg_sysfs_cache_enlist(entry);
 	return 0;
 
-err_add_raw:
+err_del_entry:
 	kobject_del(&entry->kobj);
-	kfree(entry);
+err_put_entry:
+	kobject_put(&entry->kobj);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/raspberrypi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/raspberrypi.c
@@ -9,6 +9,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/kref.h>
 #include <linux/mailbox_client.h>
+#include <linux/mailbox_controller.h>
 #include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
@@ -96,8 +97,8 @@
 	if (size & 3)
 		return -EINVAL;
 
-	buf = dma_alloc_coherent(fw->cl.dev, PAGE_ALIGN(size), &bus_addr,
-				 GFP_ATOMIC);
+	buf = dma_alloc_coherent(fw->chan->mbox->dev, PAGE_ALIGN(size),
+				 &bus_addr, GFP_ATOMIC);
 	if (!buf)
 		return -ENOMEM;
 
@@ -125,7 +126,7 @@
 		ret = -EINVAL;
 	}
 
-	dma_free_coherent(fw->cl.dev, PAGE_ALIGN(size), buf, bus_addr);
+	dma_free_coherent(fw->chan->mbox->dev, PAGE_ALIGN(size), buf, bus_addr);
 
 	return ret;
 }
@@ -272,6 +273,7 @@
 		int ret = PTR_ERR(fw->chan);
 		if (ret != -EPROBE_DEFER)
 			dev_err(dev, "Failed to get mbox channel: %d\n", ret);
+		kfree(fw);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/scpi_pm_domain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/scpi_pm_domain.c
@@ -16,7 +16,6 @@
 	struct generic_pm_domain genpd;
 	struct scpi_ops *ops;
 	u32 domain;
-	char name[30];
 };
 
 /*
@@ -110,8 +109,13 @@
 
 		scpi_pd->domain = i;
 		scpi_pd->ops = scpi_ops;
-		sprintf(scpi_pd->name, "%pOFn.%d", np, i);
-		scpi_pd->genpd.name = scpi_pd->name;
+		scpi_pd->genpd.name = devm_kasprintf(dev, GFP_KERNEL,
+						     "%pOFn.%d", np, i);
+		if (!scpi_pd->genpd.name) {
+			dev_err(dev, "Failed to allocate genpd name:%pOFn.%d\n",
+				np, i);
+			continue;
+		}
 		scpi_pd->genpd.power_off = scpi_pd_power_off;
 		scpi_pd->genpd.power_on = scpi_pd_power_on;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/smccc/smccc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/smccc/smccc.c
@@ -16,7 +16,6 @@
 static enum arm_smccc_conduit smccc_conduit = SMCCC_CONDUIT_NONE;
 
 bool __ro_after_init smccc_trng_available = false;
-u64 __ro_after_init smccc_has_sve_hint = false;
 
 void __init arm_smccc_version_init(u32 version, enum arm_smccc_conduit conduit)
 {
@@ -24,9 +23,6 @@
 	smccc_conduit = conduit;
 
 	smccc_trng_available = smccc_probe_trng();
-	if (IS_ENABLED(CONFIG_ARM64_SVE) &&
-	    smccc_version >= ARM_SMCCC_VERSION_1_3)
-		smccc_has_sve_hint = true;
 }
 
 enum arm_smccc_conduit arm_smccc_1_1_get_conduit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/smccc/soc_id.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/smccc/soc_id.c
@@ -50,7 +50,7 @@
 	arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
 			     ARM_SMCCC_ARCH_SOC_ID, &res);
 
-	if (res.a0 == SMCCC_RET_NOT_SUPPORTED) {
+	if ((int)res.a0 == SMCCC_RET_NOT_SUPPORTED) {
 		pr_info("ARCH_SOC_ID not implemented, skipping ....\n");
 		return 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/stratix10-svc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/stratix10-svc.c
@@ -477,7 +477,7 @@
 		case INTEL_SIP_SMC_RSU_ERROR:
 			pr_err("%s: STATUS_ERROR\n", __func__);
 			cbdata->status = BIT(SVC_STATUS_ERROR);
-			cbdata->kaddr1 = NULL;
+			cbdata->kaddr1 = &res.a1;
 			cbdata->kaddr2 = NULL;
 			cbdata->kaddr3 = NULL;
 			pdata->chan->scl->receive_cb(pdata->chan->scl, cbdata);
@@ -622,8 +622,8 @@
 	end = rounddown(sh_memory->addr + sh_memory->size, PAGE_SIZE);
 	paddr = begin;
 	size = end - begin;
-	va = memremap(paddr, size, MEMREMAP_WC);
-	if (!va) {
+	va = devm_memremap(dev, paddr, size, MEMREMAP_WC);
+	if (IS_ERR(va)) {
 		dev_err(dev, "fail to remap shared memory\n");
 		return ERR_PTR(-EINVAL);
 	}
@@ -941,17 +941,17 @@
 void stratix10_svc_free_memory(struct stratix10_svc_chan *chan, void *kaddr)
 {
 	struct stratix10_svc_data_mem *pmem;
-	size_t size = 0;
 
 	list_for_each_entry(pmem, &svc_data_mem, node)
 		if (pmem->vaddr == kaddr) {
-			size = pmem->size;
-			break;
+			gen_pool_free(chan->ctrl->genpool,
+				       (unsigned long)kaddr, pmem->size);
+			pmem->vaddr = NULL;
+			list_del(&pmem->node);
+			return;
 		}
 
-	gen_pool_free(chan->ctrl->genpool, (unsigned long)kaddr, size);
-	pmem->vaddr = NULL;
-	list_del(&pmem->node);
+	list_del(&svc_data_mem);
 }
 EXPORT_SYMBOL_GPL(stratix10_svc_free_memory);
 
@@ -989,18 +989,22 @@
 		return ret;
 
 	genpool = svc_create_memory_pool(pdev, sh_memory);
-	if (!genpool)
-		return -ENOMEM;
+	if (IS_ERR(genpool))
+		return PTR_ERR(genpool);
 
 	/* allocate service controller and supporting channel */
 	controller = devm_kzalloc(dev, sizeof(*controller), GFP_KERNEL);
-	if (!controller)
-		return -ENOMEM;
+	if (!controller) {
+		ret = -ENOMEM;
+		goto err_destroy_pool;
+	}
 
 	chans = devm_kmalloc_array(dev, SVC_NUM_CHANNEL,
 				   sizeof(*chans), GFP_KERNEL | __GFP_ZERO);
-	if (!chans)
-		return -ENOMEM;
+	if (!chans) {
+		ret = -ENOMEM;
+		goto err_destroy_pool;
+	}
 
 	controller->dev = dev;
 	controller->num_chans = SVC_NUM_CHANNEL;
@@ -1015,7 +1019,7 @@
 	ret = kfifo_alloc(&controller->svc_fifo, fifo_size, GFP_KERNEL);
 	if (ret) {
 		dev_err(dev, "failed to allocate FIFO\n");
-		return ret;
+		goto err_destroy_pool;
 	}
 	spin_lock_init(&controller->svc_fifo_lock);
 
@@ -1060,6 +1064,8 @@
 	platform_device_put(svc->stratix10_svc_rsu);
 err_free_kfifo:
 	kfifo_free(&controller->svc_fifo);
+err_destroy_pool:
+	gen_pool_destroy(genpool);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/sysfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/sysfb.c
@@ -34,21 +34,61 @@
 #include <linux/screen_info.h>
 #include <linux/sysfb.h>
 
+static struct platform_device *pd;
+static DEFINE_MUTEX(disable_lock);
+static bool disabled;
+
+static bool sysfb_unregister(void)
+{
+	if (IS_ERR_OR_NULL(pd))
+		return false;
+
+	platform_device_unregister(pd);
+	pd = NULL;
+
+	return true;
+}
+
+/**
+ * sysfb_disable() - disable the Generic System Framebuffers support
+ *
+ * This disables the registration of system framebuffer devices that match the
+ * generic drivers that make use of the system framebuffer set up by firmware.
+ *
+ * It also unregisters a device if this was already registered by sysfb_init().
+ *
+ * Context: The function can sleep. A @disable_lock mutex is acquired to serialize
+ *          against sysfb_init(), that registers a system framebuffer device.
+ */
+void sysfb_disable(void)
+{
+	mutex_lock(&disable_lock);
+	sysfb_unregister();
+	disabled = true;
+	mutex_unlock(&disable_lock);
+}
+EXPORT_SYMBOL_GPL(sysfb_disable);
+
 static __init int sysfb_init(void)
 {
 	struct screen_info *si = &screen_info;
 	struct simplefb_platform_data mode;
-	struct platform_device *pd;
 	const char *name;
 	bool compatible;
-	int ret;
+	int ret = 0;
+
+	mutex_lock(&disable_lock);
+	if (disabled)
+		goto unlock_mutex;
+
+	sysfb_apply_efi_quirks();
 
 	/* try to create a simple-framebuffer device */
 	compatible = sysfb_parse_mode(si, &mode);
 	if (compatible) {
-		ret = sysfb_create_simplefb(si, &mode);
-		if (!ret)
-			return 0;
+		pd = sysfb_create_simplefb(si, &mode);
+		if (!IS_ERR(pd))
+			goto unlock_mutex;
 	}
 
 	/* if the FB is incompatible, create a legacy framebuffer device */
@@ -60,10 +100,12 @@
 		name = "platform-framebuffer";
 
 	pd = platform_device_alloc(name, 0);
-	if (!pd)
-		return -ENOMEM;
+	if (!pd) {
+		ret = -ENOMEM;
+		goto unlock_mutex;
+	}
 
-	sysfb_apply_efi_quirks(pd);
+	sysfb_set_efifb_fwnode(pd);
 
 	ret = platform_device_add_data(pd, si, sizeof(*si));
 	if (ret)
@@ -73,9 +115,11 @@
 	if (ret)
 		goto err;
 
-	return 0;
+	goto unlock_mutex;
 err:
 	platform_device_put(pd);
+unlock_mutex:
+	mutex_unlock(&disable_lock);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/sysfb_simplefb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/sysfb_simplefb.c
@@ -57,8 +57,8 @@
 	return false;
 }
 
-__init int sysfb_create_simplefb(const struct screen_info *si,
-				 const struct simplefb_platform_data *mode)
+__init struct platform_device *sysfb_create_simplefb(const struct screen_info *si,
+						     const struct simplefb_platform_data *mode)
 {
 	struct platform_device *pd;
 	struct resource res;
@@ -76,7 +76,7 @@
 		base |= (u64)si->ext_lfb_base << 32;
 	if (!base || (u64)(resource_size_t)base != base) {
 		printk(KERN_DEBUG "sysfb: inaccessible VRAM base\n");
-		return -EINVAL;
+		return ERR_PTR(-EINVAL);
 	}
 
 	/*
@@ -93,7 +93,7 @@
 	length = mode->height * mode->stride;
 	if (length > size) {
 		printk(KERN_WARNING "sysfb: VRAM smaller than advertised\n");
-		return -EINVAL;
+		return ERR_PTR(-EINVAL);
 	}
 	length = PAGE_ALIGN(length);
 
@@ -104,21 +104,30 @@
 	res.start = base;
 	res.end = res.start + length - 1;
 	if (res.end <= res.start)
-		return -EINVAL;
+		return ERR_PTR(-EINVAL);
 
 	pd = platform_device_alloc("simple-framebuffer", 0);
 	if (!pd)
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
 
-	sysfb_apply_efi_quirks(pd);
+	sysfb_set_efifb_fwnode(pd);
 
 	ret = platform_device_add_resources(pd, &res, 1);
 	if (ret)
-		return ret;
+		goto err_put_device;
 
 	ret = platform_device_add_data(pd, mode, sizeof(*mode));
 	if (ret)
-		return ret;
+		goto err_put_device;
 
-	return platform_device_add(pd);
+	ret = platform_device_add(pd);
+	if (ret)
+		goto err_put_device;
+
+	return pd;
+
+err_put_device:
+	platform_device_put(pd);
+
+	return ERR_PTR(ret);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/tegra/bpmp-debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/tegra/bpmp-debugfs.c
@@ -465,7 +465,7 @@
 			mode |= attrs & DEBUGFS_S_IWUSR ? 0200 : 0;
 			dentry = debugfs_create_file(name, mode, parent, bpmp,
 						     &bpmp_debug_fops);
-			if (!dentry) {
+			if (IS_ERR(dentry)) {
 				err = -ENOMEM;
 				goto out;
 			}
@@ -716,7 +716,7 @@
 
 		if (t & DEBUGFS_S_ISDIR) {
 			dentry = debugfs_create_dir(name, parent);
-			if (!dentry)
+			if (IS_ERR(dentry))
 				return -ENOMEM;
 			err = bpmp_populate_dir(bpmp, seqbuf, dentry, depth+1);
 			if (err < 0)
@@ -729,7 +729,7 @@
 			dentry = debugfs_create_file(name, mode,
 						     parent, bpmp,
 						     &debugfs_fops);
-			if (!dentry)
+			if (IS_ERR(dentry))
 				return -ENOMEM;
 		}
 	}
@@ -779,11 +779,11 @@
 		return 0;
 
 	root = debugfs_create_dir("bpmp", NULL);
-	if (!root)
+	if (IS_ERR(root))
 		return -ENOMEM;
 
 	bpmp->debugfs_mirror = debugfs_create_dir("debug", root);
-	if (!bpmp->debugfs_mirror) {
+	if (IS_ERR(bpmp->debugfs_mirror)) {
 		err = -ENOMEM;
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/tegra/bpmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/tegra/bpmp.c
@@ -25,12 +25,6 @@
 #define MSG_RING	BIT(1)
 #define TAG_SZ		32
 
-static inline struct tegra_bpmp *
-mbox_client_to_bpmp(struct mbox_client *client)
-{
-	return container_of(client, struct tegra_bpmp, mbox.client);
-}
-
 static inline const struct tegra_bpmp_ops *
 channel_to_ops(struct tegra_bpmp_channel *channel)
 {
@@ -201,7 +195,7 @@
 	int err;
 
 	if (data && size > 0)
-		memcpy(data, channel->ib->data, size);
+		memcpy_fromio(data, channel->ib->data, size);
 
 	err = tegra_bpmp_ack_response(channel);
 	if (err < 0)
@@ -245,7 +239,7 @@
 	channel->ob->flags = flags;
 
 	if (data && size > 0)
-		memcpy(channel->ob->data, data, size);
+		memcpy_toio(channel->ob->data, data, size);
 
 	return tegra_bpmp_post_request(channel);
 }
@@ -420,7 +414,7 @@
 	channel->ob->code = code;
 
 	if (data && size > 0)
-		memcpy(channel->ob->data, data, size);
+		memcpy_toio(channel->ob->data, data, size);
 
 	err = tegra_bpmp_post_response(channel);
 	if (WARN_ON(err < 0))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/ti_sci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/ti_sci.c
@@ -161,7 +161,7 @@
 {
 	struct device *dev = &pdev->dev;
 	struct resource *res;
-	char debug_name[50] = "ti_sci_debug@";
+	char debug_name[50];
 
 	/* Debug region is optional */
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
@@ -178,10 +178,10 @@
 	/* Setup NULL termination */
 	info->debug_buffer[info->debug_region_size] = 0;
 
-	info->d = debugfs_create_file(strncat(debug_name, dev_name(dev),
-					      sizeof(debug_name) -
-					      sizeof("ti_sci_debug@")),
-				      0444, NULL, info, &ti_sci_debug_fops);
+	snprintf(debug_name, sizeof(debug_name), "ti_sci_debug@%s",
+		 dev_name(dev));
+	info->d = debugfs_create_file(debug_name, 0444, NULL, info,
+				      &ti_sci_debug_fops);
 	if (IS_ERR(info->d))
 		return PTR_ERR(info->d);
 
@@ -190,19 +190,6 @@
 	return 0;
 }
 
-/**
- * ti_sci_debugfs_destroy() - clean up log debug file
- * @pdev:	platform device pointer
- * @info:	Pointer to SCI entity information
- */
-static void ti_sci_debugfs_destroy(struct platform_device *pdev,
-				   struct ti_sci_info *info)
-{
-	if (IS_ERR(info->debug_region))
-		return;
-
-	debugfs_remove(info->d);
-}
 #else /* CONFIG_DEBUG_FS */
 static inline int ti_sci_debugfs_create(struct platform_device *dev,
 					struct ti_sci_info *info)
@@ -3435,43 +3422,12 @@
 	return ret;
 }
 
-static int ti_sci_remove(struct platform_device *pdev)
-{
-	struct ti_sci_info *info;
-	struct device *dev = &pdev->dev;
-	int ret = 0;
-
-	of_platform_depopulate(dev);
-
-	info = platform_get_drvdata(pdev);
-
-	if (info->nb.notifier_call)
-		unregister_restart_handler(&info->nb);
-
-	mutex_lock(&ti_sci_list_mutex);
-	if (info->users)
-		ret = -EBUSY;
-	else
-		list_del(&info->node);
-	mutex_unlock(&ti_sci_list_mutex);
-
-	if (!ret) {
-		ti_sci_debugfs_destroy(pdev, info);
-
-		/* Safe to free channels since no more users */
-		mbox_free_channel(info->chan_tx);
-		mbox_free_channel(info->chan_rx);
-	}
-
-	return ret;
-}
-
 static struct platform_driver ti_sci_driver = {
 	.probe = ti_sci_probe,
-	.remove = ti_sci_remove,
 	.driver = {
 		   .name = "ti-sci",
 		   .of_match_table = of_match_ptr(ti_sci_of_match),
+		   .suppress_bind_attrs = true,
 	},
 };
 module_platform_driver(ti_sci_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/turris-mox-rwtm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/turris-mox-rwtm.c
@@ -2,7 +2,7 @@
 /*
  * Turris Mox rWTM firmware driver
  *
- * Copyright (C) 2019 Marek Behún <kabel@kernel.org>
+ * Copyright (C) 2019, 2024 Marek Behún <kabel@kernel.org>
  */
 
 #include <linux/armada-37xx-rwtm-mailbox.h>
@@ -174,6 +174,9 @@
 	struct mox_rwtm *rwtm = dev_get_drvdata(cl->dev);
 	struct armada_37xx_rwtm_rx_msg *msg = data;
 
+	if (completion_done(&rwtm->cmd_done))
+		return;
+
 	rwtm->reply = *msg;
 	complete(&rwtm->cmd_done);
 }
@@ -199,9 +202,8 @@
 	if (ret < 0)
 		return ret;
 
-	ret = wait_for_completion_timeout(&rwtm->cmd_done, HZ / 2);
-	if (ret < 0)
-		return ret;
+	if (!wait_for_completion_timeout(&rwtm->cmd_done, HZ / 2))
+		return -ETIMEDOUT;
 
 	ret = mox_get_status(MBOX_CMD_BOARD_INFO, reply->retval);
 	if (ret == -ENODATA) {
@@ -235,9 +237,8 @@
 	if (ret < 0)
 		return ret;
 
-	ret = wait_for_completion_timeout(&rwtm->cmd_done, HZ / 2);
-	if (ret < 0)
-		return ret;
+	if (!wait_for_completion_timeout(&rwtm->cmd_done, HZ / 2))
+		return -ETIMEDOUT;
 
 	ret = mox_get_status(MBOX_CMD_ECDSA_PUB_KEY, reply->retval);
 	if (ret == -ENODATA) {
@@ -274,9 +275,8 @@
 	if (ret < 0)
 		return ret;
 
-	ret = wait_for_completion_timeout(&rwtm->cmd_done, HZ / 2);
-	if (ret < 0)
-		return ret;
+	if (!wait_for_completion_timeout(&rwtm->cmd_done, HZ / 2))
+		return -ETIMEDOUT;
 
 	return mox_get_status(MBOX_CMD_GET_RANDOM, rwtm->reply.retval);
 }
@@ -499,6 +499,7 @@
 	platform_set_drvdata(pdev, rwtm);
 
 	mutex_init(&rwtm->busy);
+	init_completion(&rwtm->cmd_done);
 
 	rwtm->mbox_client.dev = dev;
 	rwtm->mbox_client.rx_callback = mox_rwtm_rx_callback;
@@ -512,8 +513,6 @@
 		goto remove_files;
 	}
 
-	init_completion(&rwtm->cmd_done);
-
 	ret = mox_get_board_info(rwtm);
 	if (ret < 0)
 		dev_warn(dev, "Cannot read board information: %i\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/xilinx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/xilinx/Kconfig
@@ -23,4 +23,12 @@
 	  Say yes to enable ZynqMP firmware interface debug APIs.
 	  If in doubt, say N.
 
+config ZYNQMP_FIRMWARE_SECURE
+	bool "Enable Xilinx Zynq MPSoC secure firmware loading APIs"
+	help
+	  Firmware secure driver is used as an interface to load
+	  Authenticated and/or Encrypted firmware with single loadable
+	  partition. Say yes to enable ZynqMP secure firmware loading
+	  APIs.If in doubt, say N
+
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/xilinx/Makefile
@@ -3,3 +3,4 @@
 
 obj-$(CONFIG_ZYNQMP_FIRMWARE) += zynqmp.o
 obj-$(CONFIG_ZYNQMP_FIRMWARE_DEBUG) += zynqmp-debug.o
+obj-$(CONFIG_ZYNQMP_FIRMWARE_SECURE) += zynqmp-secure.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/xilinx/zynqmp-debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/xilinx/zynqmp-debug.c
@@ -2,7 +2,7 @@
 /*
  * Xilinx Zynq MPSoC Firmware layer for debugfs APIs
  *
- *  Copyright (C) 2014-2018 Xilinx, Inc.
+ *  Copyright (C) 2014-2021 Xilinx, Inc.
  *
  *  Michal Simek <michal.simek@xilinx.com>
  *  Davorin Mista <davorin.mista@aggios.com>
@@ -31,13 +31,93 @@
 
 #define PM_API(id)		 {id, #id, strlen(#id)}
 static struct pm_api_info pm_api_list[] = {
+	PM_API(PM_REQUEST_SUSPEND),
+	PM_API(PM_SELF_SUSPEND),
+	PM_API(PM_FORCE_POWERDOWN),
+	PM_API(PM_ABORT_SUSPEND),
+	PM_API(PM_REQUEST_WAKEUP),
+	PM_API(PM_SET_WAKEUP_SOURCE),
+	PM_API(PM_SYSTEM_SHUTDOWN),
+	PM_API(PM_REQUEST_NODE),
+	PM_API(PM_RELEASE_NODE),
+	PM_API(PM_SET_REQUIREMENT),
+	PM_API(PM_SET_MAX_LATENCY),
 	PM_API(PM_GET_API_VERSION),
+	PM_API(PM_SET_CONFIGURATION),
+	PM_API(PM_GET_NODE_STATUS),
+	PM_API(PM_GET_OPERATING_CHARACTERISTIC),
+	PM_API(PM_REGISTER_NOTIFIER),
+	PM_API(PM_RESET_ASSERT),
+	PM_API(PM_RESET_GET_STATUS),
+	PM_API(PM_GET_CHIPID),
+	PM_API(PM_PINCTRL_GET_FUNCTION),
+	PM_API(PM_PINCTRL_SET_FUNCTION),
+	PM_API(PM_PINCTRL_CONFIG_PARAM_GET),
+	PM_API(PM_PINCTRL_CONFIG_PARAM_SET),
+	PM_API(PM_IOCTL),
+	PM_API(PM_CLOCK_ENABLE),
+	PM_API(PM_CLOCK_DISABLE),
+	PM_API(PM_CLOCK_GETSTATE),
+	PM_API(PM_CLOCK_SETDIVIDER),
+	PM_API(PM_CLOCK_GETDIVIDER),
+	PM_API(PM_CLOCK_SETRATE),
+	PM_API(PM_CLOCK_GETRATE),
+	PM_API(PM_CLOCK_SETPARENT),
+	PM_API(PM_CLOCK_GETPARENT),
 	PM_API(PM_QUERY_DATA),
+	PM_API(PM_MMIO_WRITE),
+	PM_API(PM_MMIO_READ),
 };
 
 static struct dentry *firmware_debugfs_root;
 
 /**
+ * zynqmp_pm_self_suspend - PM call for master to suspend itself
+ * @node:	Node ID of the master or subsystem
+ * @latency:	Requested maximum wakeup latency (not supported)
+ * @state:	Requested state (not supported)
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+static int zynqmp_pm_self_suspend(const u32 node, const u32 latency,
+				  const u32 state)
+{
+	return zynqmp_pm_invoke_fn(PM_SELF_SUSPEND, node, latency,
+				   state, 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_abort_suspend - PM call to announce that a prior suspend request
+ *				is to be aborted.
+ * @reason:	Reason for the abort
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+static int zynqmp_pm_abort_suspend(const enum zynqmp_pm_abort_reason reason)
+{
+	return zynqmp_pm_invoke_fn(PM_ABORT_SUSPEND, reason, 0, 0, 0, 0,
+				   NULL);
+}
+
+/**
+ * zynqmp_pm_ioctl - PM IOCTL for device control and configs
+ * @node:	Node ID of the device
+ * @ioctl:	ID of the requested IOCTL
+ * @arg1:	Argument 1 of requested IOCTL call
+ * @arg2:	Argument 2 of requested IOCTL call
+ * @arg3:	Argument 3 of requested IOCTL call
+ * @out:	Returned output value
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+static int zynqmp_pm_ioctl(const u32 node, const u32 ioctl, const u32 arg1,
+			   const u32 arg2, const u32 arg3, u32 *out)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, ioctl, arg1, arg2, arg3,
+				   out);
+}
+
+/**
  * zynqmp_pm_argument_value() - Extract argument value from a PM-API request
  * @arg:	Entered PM-API argument in string format
  *
@@ -86,6 +166,7 @@
 static int process_api_request(u32 pm_id, u64 *pm_api_arg, u32 *pm_api_ret)
 {
 	u32 pm_api_version;
+	u64 rate;
 	int ret;
 	struct zynqmp_pm_query_data qdata = {0};
 
@@ -95,6 +176,195 @@
 		sprintf(debugfs_buf, "PM-API Version = %d.%d\n",
 			pm_api_version >> 16, pm_api_version & 0xffff);
 		break;
+	case PM_REQUEST_SUSPEND:
+		ret = zynqmp_pm_request_suspend(pm_api_arg[0],
+						pm_api_arg[1] ? pm_api_arg[1] :
+						ZYNQMP_PM_REQUEST_ACK_NO,
+						pm_api_arg[2] ? pm_api_arg[2] :
+						ZYNQMP_PM_MAX_LATENCY, 0);
+		break;
+	case PM_SELF_SUSPEND:
+		ret = zynqmp_pm_self_suspend(pm_api_arg[0],
+					     pm_api_arg[1] ? pm_api_arg[1] :
+					     ZYNQMP_PM_MAX_LATENCY, 0);
+		break;
+	case PM_FORCE_POWERDOWN:
+		ret = zynqmp_pm_force_powerdown(pm_api_arg[0],
+						pm_api_arg[1] ? pm_api_arg[1] :
+						ZYNQMP_PM_REQUEST_ACK_NO);
+		break;
+	case PM_ABORT_SUSPEND:
+		ret = zynqmp_pm_abort_suspend(pm_api_arg[0] ? pm_api_arg[0] :
+					      ZYNQMP_PM_ABORT_REASON_UNKNOWN);
+		break;
+	case PM_REQUEST_WAKEUP:
+		ret = zynqmp_pm_request_wakeup(pm_api_arg[0],
+					       pm_api_arg[1], pm_api_arg[2],
+					       pm_api_arg[3] ? pm_api_arg[3] :
+					       ZYNQMP_PM_REQUEST_ACK_NO);
+		break;
+	case PM_SET_WAKEUP_SOURCE:
+		ret = zynqmp_pm_set_wakeup_source(pm_api_arg[0], pm_api_arg[1],
+						  pm_api_arg[2]);
+		break;
+	case PM_SYSTEM_SHUTDOWN:
+		ret = zynqmp_pm_system_shutdown(pm_api_arg[0], pm_api_arg[1]);
+		break;
+	case PM_REQUEST_NODE:
+		ret = zynqmp_pm_request_node(pm_api_arg[0],
+					     pm_api_arg[1] ? pm_api_arg[1] :
+					     ZYNQMP_PM_CAPABILITY_ACCESS,
+					     pm_api_arg[2] ? pm_api_arg[2] : 0,
+					     pm_api_arg[3] ? pm_api_arg[3] :
+					     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+		break;
+	case PM_RELEASE_NODE:
+		ret = zynqmp_pm_release_node(pm_api_arg[0]);
+		break;
+	case PM_SET_REQUIREMENT:
+		ret = zynqmp_pm_set_requirement(pm_api_arg[0],
+						pm_api_arg[1] ? pm_api_arg[1] :
+						ZYNQMP_PM_CAPABILITY_CONTEXT,
+						pm_api_arg[2] ?
+						pm_api_arg[2] : 0,
+						pm_api_arg[3] ? pm_api_arg[3] :
+						ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+		break;
+	case PM_SET_MAX_LATENCY:
+		ret = zynqmp_pm_set_max_latency(pm_api_arg[0],
+						pm_api_arg[1] ? pm_api_arg[1] :
+						ZYNQMP_PM_MAX_LATENCY);
+		break;
+	case PM_SET_CONFIGURATION:
+		ret = zynqmp_pm_set_configuration(pm_api_arg[0]);
+		break;
+	case PM_GET_NODE_STATUS:
+		ret = zynqmp_pm_get_node_status(pm_api_arg[0],
+						&pm_api_ret[0],
+						&pm_api_ret[1],
+						&pm_api_ret[2]);
+		if (!ret)
+			sprintf(debugfs_buf,
+				"GET_NODE_STATUS:\n\tNodeId: %llu\n\tStatus: %u\n\tRequirements: %u\n\tUsage: %u\n",
+				pm_api_arg[0], pm_api_ret[0],
+				pm_api_ret[1], pm_api_ret[2]);
+		break;
+	case PM_GET_OPERATING_CHARACTERISTIC:
+		ret = zynqmp_pm_get_operating_characteristic(pm_api_arg[0],
+							     pm_api_arg[1] ? pm_api_arg[1] :
+				ZYNQMP_PM_OPERATING_CHARACTERISTIC_POWER,
+				&pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf,
+				"GET_OPERATING_CHARACTERISTIC:\n\tNodeId: %llu\n\tType: %llu\n\tResult: %u\n",
+				pm_api_arg[0], pm_api_arg[1],
+				pm_api_ret[0]);
+		break;
+	case PM_REGISTER_NOTIFIER:
+		ret = zynqmp_pm_register_notifier(pm_api_arg[0],
+						  pm_api_arg[1] ?
+						  pm_api_arg[1] : 0,
+						  pm_api_arg[2] ?
+						  pm_api_arg[2] : 0,
+						  pm_api_arg[3] ?
+						  pm_api_arg[3] : 0);
+		break;
+	case PM_RESET_ASSERT:
+		ret = zynqmp_pm_reset_assert(pm_api_arg[0], pm_api_arg[1]);
+		break;
+	case PM_RESET_GET_STATUS:
+		ret = zynqmp_pm_reset_get_status(pm_api_arg[0], &pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf, "Reset status: %u\n",
+				pm_api_ret[0]);
+		break;
+	case PM_GET_CHIPID:
+		ret = zynqmp_pm_get_chipid(&pm_api_ret[0], &pm_api_ret[1]);
+		if (!ret)
+			sprintf(debugfs_buf, "Idcode: %#x, Version:%#x\n",
+				pm_api_ret[0], pm_api_ret[1]);
+		break;
+	case PM_PINCTRL_GET_FUNCTION:
+		ret = zynqmp_pm_pinctrl_get_function(pm_api_arg[0],
+						     &pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf,
+				"Current set function for the pin: %u\n",
+				pm_api_ret[0]);
+		break;
+	case PM_PINCTRL_SET_FUNCTION:
+		ret = zynqmp_pm_pinctrl_set_function(pm_api_arg[0],
+						     pm_api_arg[1]);
+		break;
+	case PM_PINCTRL_CONFIG_PARAM_GET:
+		ret = zynqmp_pm_pinctrl_get_config(pm_api_arg[0], pm_api_arg[1],
+						   &pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf,
+				"Pin: %llu, Param: %llu, Value: %u\n",
+				pm_api_arg[0], pm_api_arg[1],
+				pm_api_ret[0]);
+		break;
+	case PM_PINCTRL_CONFIG_PARAM_SET:
+		ret = zynqmp_pm_pinctrl_set_config(pm_api_arg[0],
+						   pm_api_arg[1],
+						   pm_api_arg[2]);
+		break;
+	case PM_IOCTL:
+		ret = zynqmp_pm_ioctl(pm_api_arg[0], pm_api_arg[1],
+				      pm_api_arg[2], pm_api_arg[3],
+				      pm_api_arg[4], &pm_api_ret[0]);
+		if (!ret && (pm_api_arg[1] == IOCTL_GET_RPU_OPER_MODE ||
+			     pm_api_arg[1] == IOCTL_GET_PLL_FRAC_MODE ||
+			     pm_api_arg[1] == IOCTL_GET_PLL_FRAC_DATA ||
+			     pm_api_arg[1] == IOCTL_READ_GGS ||
+			     pm_api_arg[1] == IOCTL_READ_PGGS ||
+			     pm_api_arg[1] == IOCTL_PROBE_COUNTER_READ ||
+			     pm_api_arg[1] == IOCTL_READ_REG))
+			sprintf(debugfs_buf, "IOCTL return value: %u\n",
+				pm_api_ret[1]);
+		if (!ret && pm_api_arg[1] == IOCTL_GET_QOS)
+			sprintf(debugfs_buf, "Default QoS: %u\nCurrent QoS: %u\n",
+				pm_api_ret[1], pm_api_ret[2]);
+		break;
+	case PM_CLOCK_ENABLE:
+		ret = zynqmp_pm_clock_enable(pm_api_arg[0]);
+		break;
+	case PM_CLOCK_DISABLE:
+		ret = zynqmp_pm_clock_disable(pm_api_arg[0]);
+		break;
+	case PM_CLOCK_GETSTATE:
+		ret = zynqmp_pm_clock_getstate(pm_api_arg[0], &pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf, "Clock state: %u\n",
+				pm_api_ret[0]);
+		break;
+	case PM_CLOCK_SETDIVIDER:
+		ret = zynqmp_pm_clock_setdivider(pm_api_arg[0], pm_api_arg[1]);
+		break;
+	case PM_CLOCK_GETDIVIDER:
+		ret = zynqmp_pm_clock_getdivider(pm_api_arg[0], &pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf, "Divider Value: %d\n",
+				pm_api_ret[0]);
+		break;
+	case PM_CLOCK_SETRATE:
+		ret = zynqmp_pm_clock_setrate(pm_api_arg[0], pm_api_arg[1]);
+		break;
+	case PM_CLOCK_GETRATE:
+		ret = zynqmp_pm_clock_getrate(pm_api_arg[0], &rate);
+		if (!ret)
+			sprintf(debugfs_buf, "Clock rate :%llu\n", rate);
+		break;
+	case PM_CLOCK_SETPARENT:
+		ret = zynqmp_pm_clock_setparent(pm_api_arg[0], pm_api_arg[1]);
+		break;
+	case PM_CLOCK_GETPARENT:
+		ret = zynqmp_pm_clock_getparent(pm_api_arg[0], &pm_api_ret[0]);
+		if (!ret)
+			sprintf(debugfs_buf,
+				"Clock parent Index: %u\n", pm_api_ret[0]);
+		break;
 	case PM_QUERY_DATA:
 		qdata.qid = pm_api_arg[0];
 		qdata.arg1 = pm_api_arg[1];
@@ -121,6 +391,14 @@
 				pm_api_ret[2], pm_api_ret[3]);
 		}
 		break;
+	case PM_MMIO_WRITE:
+		ret = zynqmp_pm_mmio_write(pm_api_arg[0], pm_api_arg[1],
+					   pm_api_arg[2]);
+		break;
+	case PM_MMIO_READ:
+		ret = zynqmp_pm_mmio_read(pm_api_arg[0], &pm_api_ret[0]);
+		sprintf(debugfs_buf, "REG value: 0x%x\n", pm_api_ret[0]);
+		break;
 	default:
 		sprintf(debugfs_buf, "Unsupported PM-API request\n");
 		ret = -EINVAL;
@@ -150,7 +428,7 @@
 	char *kern_buff, *tmp_buff;
 	char *pm_api_req;
 	u32 pm_id = 0;
-	u64 pm_api_arg[4] = {0, 0, 0, 0};
+	u64 pm_api_arg[5] = {0, 0, 0, 0, 0};
 	/* Return values from PM APIs calls */
 	u32 pm_api_ret[4] = {0, 0, 0, 0};
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/xilinx/zynqmp-secure.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/xilinx/zynqmp-secure.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx ZynqMP SecureFw Driver.
+ * Copyright (c) 2018 Xilinx Inc.
+ */
+
+#include <asm/cacheflush.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/firmware.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+
+#define ZYNQMP_AES_KEY_SIZE	64
+
+static u8 key[ZYNQMP_AES_KEY_SIZE] = {0};
+static dma_addr_t dma_addr;
+static u8 *keyptr;
+static size_t dma_size;
+static char *kbuf;
+
+static ssize_t secure_load_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	const struct firmware *fw;
+	char image_name[NAME_MAX];
+	u64 dst, ret;
+	int len;
+
+	strncpy(image_name, buf, NAME_MAX);
+	len = strlen(image_name);
+	if (image_name[len - 1] == '\n')
+		image_name[len - 1] = 0;
+
+	ret = request_firmware(&fw, image_name, dev);
+	if (ret) {
+		dev_err(dev, "Error requesting firmware %s\n", image_name);
+		return ret;
+	}
+	dma_size = fw->size;
+
+	if (keyptr)
+		dma_size = fw->size + ZYNQMP_AES_KEY_SIZE;
+
+	kbuf = dma_alloc_coherent(dev, dma_size,
+				  &dma_addr, GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	memcpy(kbuf, fw->data, fw->size);
+
+	if (keyptr)
+		memcpy(kbuf + fw->size, key, ZYNQMP_AES_KEY_SIZE);
+
+	/* To ensure cache coherency */
+	caches_clean_inval_user_pou((unsigned long)kbuf,
+				    (unsigned long)kbuf + dma_size);
+	release_firmware(fw);
+
+	if (keyptr)
+		ret = zynqmp_pm_secure_load(dma_addr, dma_addr + fw->size,
+					    &dst);
+	else
+		ret = zynqmp_pm_secure_load(dma_addr, 0, &dst);
+
+	if (ret) {
+		dev_info(dev, "Failed to load secure image \r\n");
+		return ret;
+	}
+	dev_info(dev, "Verified image at 0x%llx\n", dst);
+
+	return count;
+}
+
+static ssize_t key_show(struct device *dev,
+			struct device_attribute *attr,
+			char *buf)
+{
+	return snprintf(buf, ZYNQMP_AES_KEY_SIZE + 1, "%s\n", key);
+}
+
+static ssize_t key_store(struct device *dev,
+			 struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	memcpy(key, buf, count);
+	keyptr = &key[0];
+	return count;
+}
+
+static ssize_t secure_load_done_store(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buf, size_t count)
+{
+	int ret;
+	unsigned int value;
+
+	ret = kstrtouint(buf, 10, &value);
+	if (ret)
+		return ret;
+	if (value)
+		dma_free_coherent(dev, dma_size, kbuf, dma_addr);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(key);
+static DEVICE_ATTR_WO(secure_load);
+static DEVICE_ATTR_WO(secure_load_done);
+
+static struct attribute *securefw_attrs[] = {
+	&dev_attr_secure_load_done.attr,
+	&dev_attr_secure_load.attr,
+	&dev_attr_key.attr,
+	NULL,
+};
+
+ATTRIBUTE_GROUPS(securefw);
+
+static int securefw_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct platform_device *securefw_pdev;
+
+	securefw_pdev = pdev;
+
+	securefw_pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+
+	ret = of_dma_configure(&securefw_pdev->dev, NULL, true);
+	if (ret < 0) {
+		dev_info(&securefw_pdev->dev, "Cannot setup DMA ops\r\n");
+		return ret;
+	}
+
+	ret = sysfs_create_groups(&securefw_pdev->dev.kobj, securefw_groups);
+	if (ret)
+		return ret;
+
+	dev_info(&securefw_pdev->dev, "securefw probed\r\n");
+	return ret;
+}
+
+static int securefw_remove(struct platform_device *pdev)
+{
+	sysfs_remove_groups(&pdev->dev.kobj, securefw_groups);
+	return 0;
+}
+
+static struct platform_driver securefw_driver = {
+	.driver = {
+		.name = "securefw",
+	},
+	.probe = securefw_probe,
+	.remove = securefw_remove,
+};
+
+static struct platform_device *securefw_dev_reg;
+
+static int __init zynqmp_secure_init(void)
+{
+	int ret;
+
+	ret = platform_driver_register(&securefw_driver);
+	if (ret)
+		return ret;
+
+	securefw_dev_reg = platform_device_register_simple("securefw", -1,
+							   NULL, 0);
+	if (IS_ERR(securefw_dev_reg)) {
+		ret = PTR_ERR(securefw_dev_reg);
+		platform_driver_unregister(&securefw_driver);
+		return ret;
+	}
+	return 0;
+}
+
+static void __exit zynqmp_secure_exit(void)
+{
+	platform_device_unregister(securefw_dev_reg);
+	platform_driver_unregister(&securefw_driver);
+}
+
+module_init(zynqmp_secure_init);
+module_exit(zynqmp_secure_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/firmware/xilinx/zynqmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/firmware/xilinx/zynqmp.c
@@ -13,6 +13,8 @@
 #include <linux/arm-smccc.h>
 #include <linux/compiler.h>
 #include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/firmware.h>
 #include <linux/init.h>
 #include <linux/mfd/core.h>
 #include <linux/module.h>
@@ -23,13 +25,36 @@
 #include <linux/hashtable.h>
 
 #include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/firmware/xlnx-event-manager.h>
 #include "zynqmp-debug.h"
 
 /* Max HashMap Order for PM API feature check (1<<7 = 128) */
 #define PM_API_FEATURE_CHECK_MAX_ORDER  7
 
+/* CRL registers and bitfields */
+#define CRL_APB_BASE			0xFF5E0000U
+/* BOOT_PIN_CTRL- Used to control the mode pins after boot */
+#define CRL_APB_BOOT_PIN_CTRL		(CRL_APB_BASE + (0x250U))
+/* BOOT_PIN_CTRL_MASK- out_val[11:8], out_en[3:0] */
+#define CRL_APB_BOOTPIN_CTRL_MASK	0xF0FU
+
+/* firmware required uid buff size */
+#define UID_BUFF_SIZE	786
+#define UID_SET_LEN	4
+#define UID_LEN		4
+
+/* IOCTL/QUERY feature payload size */
+#define FEATURE_PAYLOAD_SIZE		2
+
 static bool feature_check_enabled;
 static DEFINE_HASHTABLE(pm_api_features_map, PM_API_FEATURE_CHECK_MAX_ORDER);
+static u32 ioctl_features[FEATURE_PAYLOAD_SIZE];
+static u32 query_features[FEATURE_PAYLOAD_SIZE];
+
+static unsigned long register_address;
+static struct platform_device *em_dev;
+
+static char image_name[NAME_MAX];
 
 /**
  * struct pm_api_feature_data - PM API Feature data
@@ -63,6 +88,8 @@
 		return 0;
 	case XST_PM_NO_FEATURE:
 		return -ENOTSUPP;
+	case XST_PM_INVALID_VERSION:
+		return -ENOTSUPP;
 	case XST_PM_NO_ACCESS:
 		return -EACCES;
 	case XST_PM_ABORT_SUSPEND:
@@ -77,7 +104,7 @@
 	}
 }
 
-static noinline int do_fw_call_fail(u64 arg0, u64 arg1, u64 arg2,
+static noinline int do_fw_call_fail(u64 arg0, u64 arg1, u64 arg2, u64 arg3,
 				    u32 *ret_payload)
 {
 	return -ENODEV;
@@ -87,25 +114,26 @@
  * PM function call wrapper
  * Invoke do_fw_call_smc or do_fw_call_hvc, depending on the configuration
  */
-static int (*do_fw_call)(u64, u64, u64, u32 *ret_payload) = do_fw_call_fail;
+static int (*do_fw_call)(u64, u64, u64, u64, u32 *ret_payload) = do_fw_call_fail;
 
 /**
  * do_fw_call_smc() - Call system-level platform management layer (SMC)
  * @arg0:		Argument 0 to SMC call
  * @arg1:		Argument 1 to SMC call
  * @arg2:		Argument 2 to SMC call
+ * @arg3:		Argument 3 to SMC call
  * @ret_payload:	Returned value array
  *
  * Invoke platform management function via SMC call (no hypervisor present).
  *
  * Return: Returns status, either success or error+reason
  */
-static noinline int do_fw_call_smc(u64 arg0, u64 arg1, u64 arg2,
+static noinline int do_fw_call_smc(u64 arg0, u64 arg1, u64 arg2, u64 arg3,
 				   u32 *ret_payload)
 {
 	struct arm_smccc_res res;
 
-	arm_smccc_smc(arg0, arg1, arg2, 0, 0, 0, 0, 0, &res);
+	arm_smccc_smc(arg0, arg1, arg2, arg3, 0, 0, 0, 0, &res);
 
 	if (ret_payload) {
 		ret_payload[0] = lower_32_bits(res.a0);
@@ -122,6 +150,7 @@
  * @arg0:		Argument 0 to HVC call
  * @arg1:		Argument 1 to HVC call
  * @arg2:		Argument 2 to HVC call
+ * @arg3:		Argument 3 to HVC call
  * @ret_payload:	Returned value array
  *
  * Invoke platform management function via HVC
@@ -130,12 +159,12 @@
  *
  * Return: Returns status, either success or error+reason
  */
-static noinline int do_fw_call_hvc(u64 arg0, u64 arg1, u64 arg2,
+static noinline int do_fw_call_hvc(u64 arg0, u64 arg1, u64 arg2, u64 arg3,
 				   u32 *ret_payload)
 {
 	struct arm_smccc_res res;
 
-	arm_smccc_hvc(arg0, arg1, arg2, 0, 0, 0, 0, 0, &res);
+	arm_smccc_hvc(arg0, arg1, arg2, arg3, 0, 0, 0, 0, &res);
 
 	if (ret_payload) {
 		ret_payload[0] = lower_32_bits(res.a0);
@@ -147,21 +176,28 @@
 	return zynqmp_pm_ret_code((enum pm_ret_status)res.a0);
 }
 
-/**
- * zynqmp_pm_feature() - Check weather given feature is supported or not
- * @api_id:		API ID to check
- *
- * Return: Returns status, either success or error+reason
- */
-static int zynqmp_pm_feature(u32 api_id)
+static int __do_feature_check_call(const u32 api_id, u32 *ret_payload)
 {
 	int ret;
-	u32 ret_payload[PAYLOAD_ARG_CNT];
 	u64 smc_arg[2];
-	struct pm_api_feature_data *feature_data;
 
-	if (!feature_check_enabled)
-		return 0;
+	smc_arg[0] = PM_SIP_SVC | PM_FEATURE_CHECK;
+	smc_arg[1] = api_id;
+
+	ret = do_fw_call(smc_arg[0], smc_arg[1], 0, 0, ret_payload);
+	if (ret)
+		ret = -EOPNOTSUPP;
+	else
+		ret = ret_payload[1];
+
+	return ret;
+}
+
+static int do_feature_check_call(const u32 api_id)
+{
+	int ret;
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	struct pm_api_feature_data *feature_data;
 
 	/* Check for existing entry in hash table for given api */
 	hash_for_each_possible(pm_api_features_map, feature_data, hentry,
@@ -171,27 +207,90 @@
 	}
 
 	/* Add new entry if not present */
-	feature_data = kmalloc(sizeof(*feature_data), GFP_KERNEL);
+	feature_data = kmalloc(sizeof(*feature_data), GFP_ATOMIC);
 	if (!feature_data)
 		return -ENOMEM;
 
 	feature_data->pm_api_id = api_id;
-	smc_arg[0] = PM_SIP_SVC | PM_FEATURE_CHECK;
-	smc_arg[1] = api_id;
-
-	ret = do_fw_call(smc_arg[0], smc_arg[1], 0, ret_payload);
-	if (ret)
-		ret = -EOPNOTSUPP;
-	else
-		ret = ret_payload[1];
+	ret = __do_feature_check_call(api_id, ret_payload);
 
 	feature_data->feature_status = ret;
 	hash_add(pm_api_features_map, &feature_data->hentry, api_id);
 
+	if (api_id == PM_IOCTL)
+		/* Store supported IOCTL IDs mask */
+		memcpy(ioctl_features, &ret_payload[2], FEATURE_PAYLOAD_SIZE * 4);
+	else if (api_id == PM_QUERY_DATA)
+		/* Store supported QUERY IDs mask */
+		memcpy(query_features, &ret_payload[2], FEATURE_PAYLOAD_SIZE * 4);
+
 	return ret;
 }
 
 /**
+ * zynqmp_pm_feature() - Check whether given feature is supported or not and
+ *			 store supported IOCTL/QUERY ID mask
+ * @api_id:		API ID to check
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_feature(const u32 api_id)
+{
+	int ret;
+
+	if (!feature_check_enabled)
+		return 0;
+
+	ret = do_feature_check_call(api_id);
+
+	return ret;
+}
+
+/**
+ * zynqmp_pm_is_function_supported() - Check whether given IOCTL/QUERY function
+ *				       is supported or not
+ * @api_id:		PM_IOCTL or PM_QUERY_DATA
+ * @id:			IOCTL or QUERY function IDs
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_is_function_supported(const u32 api_id, const u32 id)
+{
+	int ret;
+	u32 *bit_mask;
+
+	/* Input arguments validation */
+	if (id >= 64 || (api_id != PM_IOCTL && api_id != PM_QUERY_DATA))
+		return -EINVAL;
+
+	/* Check feature check API version */
+	ret = do_feature_check_call(PM_FEATURE_CHECK);
+	if (ret < 0)
+		return ret;
+
+	/* Check if feature check version 2 is supported or not */
+	if ((ret & FIRMWARE_VERSION_MASK) == PM_API_VERSION_2) {
+		/*
+		 * Call feature check for IOCTL/QUERY API to get IOCTL ID or
+		 * QUERY ID feature status.
+		 */
+		ret = do_feature_check_call(api_id);
+		if (ret < 0)
+			return ret;
+
+		bit_mask = (api_id == PM_IOCTL) ? ioctl_features : query_features;
+
+		if ((bit_mask[(id / 32)] & BIT((id % 32))) == 0U)
+			return -EOPNOTSUPP;
+	} else {
+		return -ENODATA;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_is_function_supported);
+
+/**
  * zynqmp_pm_invoke_fn() - Invoke the system-level platform management layer
  *			   caller function depending on the configuration
  * @pm_api_id:		Requested PM-API call
@@ -199,6 +298,7 @@
  * @arg1:		Argument 1 to requested PM-API call
  * @arg2:		Argument 2 to requested PM-API call
  * @arg3:		Argument 3 to requested PM-API call
+ * @arg4:		Argument 4 to requested PM-API call
  * @ret_payload:	Returned value array
  *
  * Invoke platform management function for SMC or HVC call, depending on
@@ -217,7 +317,8 @@
  * Return: Returns status, either success or error+reason
  */
 int zynqmp_pm_invoke_fn(u32 pm_api_id, u32 arg0, u32 arg1,
-			u32 arg2, u32 arg3, u32 *ret_payload)
+			u32 arg2, u32 arg3, u32 arg4,
+			u32 *ret_payload)
 {
 	/*
 	 * Added SIP service call Function Identifier
@@ -234,13 +335,29 @@
 	smc_arg[0] = PM_SIP_SVC | pm_api_id;
 	smc_arg[1] = ((u64)arg1 << 32) | arg0;
 	smc_arg[2] = ((u64)arg3 << 32) | arg2;
+	smc_arg[3] = ((u64)arg4);
 
-	return do_fw_call(smc_arg[0], smc_arg[1], smc_arg[2], ret_payload);
+	return do_fw_call(smc_arg[0], smc_arg[1], smc_arg[2], smc_arg[3],
+			  ret_payload);
 }
 
 static u32 pm_api_version;
 static u32 pm_tz_version;
 
+int zynqmp_pm_register_sgi(u32 sgi_num, u32 reset)
+{
+	int ret;
+
+	ret = zynqmp_pm_invoke_fn(TF_A_PM_REGISTER_SGI, sgi_num, reset, 0, 0,
+				  0, NULL);
+	if (ret != -ENOTSUPP && !ret)
+		return ret;
+
+	/* try old implementation as fallback strategy if above fails */
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_REGISTER_SGI, sgi_num,
+				   reset, 0, NULL);
+}
+
 /**
  * zynqmp_pm_get_api_version() - Get version number of PMU PM firmware
  * @version:	Returned version value
@@ -260,7 +377,7 @@
 		*version = pm_api_version;
 		return 0;
 	}
-	ret = zynqmp_pm_invoke_fn(PM_GET_API_VERSION, 0, 0, 0, 0, ret_payload);
+	ret = zynqmp_pm_invoke_fn(PM_GET_API_VERSION, 0, 0, 0, 0, 0, ret_payload);
 	*version = ret_payload[1];
 
 	return ret;
@@ -283,7 +400,7 @@
 	if (!idcode || !version)
 		return -EINVAL;
 
-	ret = zynqmp_pm_invoke_fn(PM_GET_CHIPID, 0, 0, 0, 0, ret_payload);
+	ret = zynqmp_pm_invoke_fn(PM_GET_CHIPID, 0, 0, 0, 0, 0, ret_payload);
 	*idcode = ret_payload[1];
 	*version = ret_payload[2];
 
@@ -311,7 +428,7 @@
 		return 0;
 	}
 	ret = zynqmp_pm_invoke_fn(PM_GET_TRUSTZONE_VERSION, 0, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*version = ret_payload[1];
 
 	return ret;
@@ -359,7 +476,7 @@
 	int ret;
 
 	ret = zynqmp_pm_invoke_fn(PM_QUERY_DATA, qdata.qid, qdata.arg1,
-				  qdata.arg2, qdata.arg3, out);
+				  qdata.arg2, qdata.arg3, 0, out);
 
 	/*
 	 * For clock name query, all bytes in SMC response are clock name
@@ -381,7 +498,8 @@
  */
 int zynqmp_pm_clock_enable(u32 clock_id)
 {
-	return zynqmp_pm_invoke_fn(PM_CLOCK_ENABLE, clock_id, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_CLOCK_ENABLE, clock_id, 0, 0, 0, 0,
+				   NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_clock_enable);
 
@@ -396,7 +514,8 @@
  */
 int zynqmp_pm_clock_disable(u32 clock_id)
 {
-	return zynqmp_pm_invoke_fn(PM_CLOCK_DISABLE, clock_id, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_CLOCK_DISABLE, clock_id, 0, 0, 0, 0,
+				   NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_clock_disable);
 
@@ -416,7 +535,7 @@
 	int ret;
 
 	ret = zynqmp_pm_invoke_fn(PM_CLOCK_GETSTATE, clock_id, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*state = ret_payload[1];
 
 	return ret;
@@ -436,7 +555,7 @@
 int zynqmp_pm_clock_setdivider(u32 clock_id, u32 divider)
 {
 	return zynqmp_pm_invoke_fn(PM_CLOCK_SETDIVIDER, clock_id, divider,
-				   0, 0, NULL);
+				   0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_clock_setdivider);
 
@@ -456,7 +575,7 @@
 	int ret;
 
 	ret = zynqmp_pm_invoke_fn(PM_CLOCK_GETDIVIDER, clock_id, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*divider = ret_payload[1];
 
 	return ret;
@@ -477,7 +596,7 @@
 	return zynqmp_pm_invoke_fn(PM_CLOCK_SETRATE, clock_id,
 				   lower_32_bits(rate),
 				   upper_32_bits(rate),
-				   0, NULL);
+				   0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_clock_setrate);
 
@@ -497,7 +616,7 @@
 	int ret;
 
 	ret = zynqmp_pm_invoke_fn(PM_CLOCK_GETRATE, clock_id, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*rate = ((u64)ret_payload[2] << 32) | ret_payload[1];
 
 	return ret;
@@ -516,7 +635,7 @@
 int zynqmp_pm_clock_setparent(u32 clock_id, u32 parent_id)
 {
 	return zynqmp_pm_invoke_fn(PM_CLOCK_SETPARENT, clock_id,
-				   parent_id, 0, 0, NULL);
+				   parent_id, 0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_clock_setparent);
 
@@ -536,7 +655,7 @@
 	int ret;
 
 	ret = zynqmp_pm_invoke_fn(PM_CLOCK_GETPARENT, clock_id, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*parent_id = ret_payload[1];
 
 	return ret;
@@ -556,7 +675,7 @@
 int zynqmp_pm_set_pll_frac_mode(u32 clk_id, u32 mode)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_SET_PLL_FRAC_MODE,
-				   clk_id, mode, NULL);
+				   clk_id, mode, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_set_pll_frac_mode);
 
@@ -573,7 +692,7 @@
 int zynqmp_pm_get_pll_frac_mode(u32 clk_id, u32 *mode)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_GET_PLL_FRAC_MODE,
-				   clk_id, 0, mode);
+				   clk_id, 0, 0, mode);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_get_pll_frac_mode);
 
@@ -591,7 +710,7 @@
 int zynqmp_pm_set_pll_frac_data(u32 clk_id, u32 data)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_SET_PLL_FRAC_DATA,
-				   clk_id, data, NULL);
+				   clk_id, data, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_set_pll_frac_data);
 
@@ -608,7 +727,7 @@
 int zynqmp_pm_get_pll_frac_data(u32 clk_id, u32 *data)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_GET_PLL_FRAC_DATA,
-				   clk_id, 0, data);
+				   clk_id, 0, 0, data);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_get_pll_frac_data);
 
@@ -626,7 +745,7 @@
 int zynqmp_pm_set_sd_tapdelay(u32 node_id, u32 type, u32 value)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, node_id, IOCTL_SET_SD_TAPDELAY,
-				   type, value, NULL);
+				   type, value, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_set_sd_tapdelay);
 
@@ -643,11 +762,28 @@
 int zynqmp_pm_sd_dll_reset(u32 node_id, u32 type)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, node_id, IOCTL_SD_DLL_RESET,
-				   type, 0, NULL);
+				   type, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_sd_dll_reset);
 
 /**
+ * zynqmp_pm_ospi_mux_select() - OSPI Mux selection
+ *
+ * @dev_id:	Device Id of the OSPI device.
+ * @select:	OSPI Mux select value.
+ *
+ * This function select the OSPI Mux.
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_ospi_mux_select(u32 dev_id, u32 select)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, dev_id, IOCTL_OSPI_MUX_SELECT,
+				   select, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_ospi_mux_select);
+
+/**
  * zynqmp_pm_write_ggs() - PM API for writing global general storage (ggs)
  * @index:	GGS register index
  * @value:	Register value to be written
@@ -659,7 +795,7 @@
 int zynqmp_pm_write_ggs(u32 index, u32 value)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_WRITE_GGS,
-				   index, value, NULL);
+				   index, value, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_write_ggs);
 
@@ -675,7 +811,7 @@
 int zynqmp_pm_read_ggs(u32 index, u32 *value)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_READ_GGS,
-				   index, 0, value);
+				   index, 0, 0, value);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_read_ggs);
 
@@ -692,7 +828,7 @@
 int zynqmp_pm_write_pggs(u32 index, u32 value)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_WRITE_PGGS, index, value,
-				   NULL);
+				   0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_write_pggs);
 
@@ -709,10 +845,66 @@
 int zynqmp_pm_read_pggs(u32 index, u32 *value)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_READ_PGGS, index, 0,
-				   value);
+				   0, value);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_read_pggs);
 
+int zynqmp_pm_usb_set_state(u32 node, u32 state, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_USB_SET_STATE, state,
+				   value, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_usb_set_state);
+
+int zynqmp_pm_ulpi_reset(void)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_ULPI_RESET, 0, 0, 0,
+				   NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_ulpi_reset);
+
+int zynqmp_pm_afi(u32 index, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_AFI, index, value, 0,
+				   NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_afi);
+
+int zynqmp_pm_set_sgmii_mode(u32 enable)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_SET_SGMII_MODE, enable, 0,
+				   0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_sgmii_mode);
+
+int zynqmp_pm_set_tapdelay_bypass(u32 index, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_SET_TAPDELAY_BYPASS,
+				   index, value, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_tapdelay_bypass);
+
+int zynqmp_pm_probe_counter_read(u32 deviceid, u32 reg, u32 *value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, deviceid, IOCTL_PROBE_COUNTER_READ, reg,
+				   0, 0, value);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_probe_counter_read);
+
+int zynqmp_pm_probe_counter_write(u32 domain, u32 reg, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, domain, IOCTL_PROBE_COUNTER_WRITE, reg,
+				   value, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_probe_counter_write);
+
+int zynqmp_pm_get_last_reset_reason(u32 *reset_reason)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_GET_LAST_RESET_REASON, 0,
+				   0, 0, reset_reason);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_last_reset_reason);
+
 /**
  * zynqmp_pm_set_boot_health_status() - PM API for setting healthy boot status
  * @value:	Status value to be written
@@ -725,8 +917,42 @@
 int zynqmp_pm_set_boot_health_status(u32 value)
 {
 	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_SET_BOOT_HEALTH_STATUS,
-				   value, 0, NULL);
+				   value, 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_clear_aie_npi_isr - Clear AI engine NPI interrupt status register
+ * @node:	AI engine node id
+ * @irq_mask:	Mask of AI engine NPI interrupt bit to clear
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_clear_aie_npi_isr(u32 node, u32 irq_mask)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_AIE_ISR_CLEAR,
+				   irq_mask, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_clear_aie_npi_isr);
+
+/**
+ * zynqmp_pm_aie_operation - AI engine run time operations
+ * @node:	AI engine node id
+ * @start_col:	Starting column of AI partition
+ * @num_col:	Number of column in AI partition
+ * @operation:	ORed value of operations
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_aie_operation(u32 node, u16 start_col, u16 num_col, u32 operation)
+{
+	u32 partition;
+
+	partition = num_col;
+	partition = ((partition << 16U) | start_col);
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_AIE_OPS,
+				   partition, operation, 0, NULL);
 }
+EXPORT_SYMBOL_GPL(zynqmp_pm_aie_operation);
 
 /**
  * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release)
@@ -736,11 +962,11 @@
  *
  * Return: Returns status, either success or error+reason
  */
-int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+int zynqmp_pm_reset_assert(const u32 reset,
 			   const enum zynqmp_pm_reset_action assert_flag)
 {
 	return zynqmp_pm_invoke_fn(PM_RESET_ASSERT, reset, assert_flag,
-				   0, 0, NULL);
+				   0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_reset_assert);
 
@@ -751,7 +977,7 @@
  *
  * Return: Returns status, either success or error+reason
  */
-int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, u32 *status)
+int zynqmp_pm_reset_get_status(const u32 reset, u32 *status)
 {
 	u32 ret_payload[PAYLOAD_ARG_CNT];
 	int ret;
@@ -760,7 +986,7 @@
 		return -EINVAL;
 
 	ret = zynqmp_pm_invoke_fn(PM_RESET_GET_STATUS, reset, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*status = ret_payload[1];
 
 	return ret;
@@ -774,16 +1000,25 @@
  * @flags:	Bitstream type
  *	-XILINX_ZYNQMP_PM_FPGA_FULL:  FPGA full reconfiguration
  *	-XILINX_ZYNQMP_PM_FPGA_PARTIAL: FPGA partial reconfiguration
+ * @status:	Returned status
  *
  * This function provides access to pmufw. To transfer
  * the required bitstream into PL.
  *
  * Return: Returns status, either success or error+reason
  */
-int zynqmp_pm_fpga_load(const u64 address, const u32 size, const u32 flags)
+int zynqmp_pm_fpga_load(const u64 address, const u32 size,
+			const u32 flags, u32 *status)
 {
-	return zynqmp_pm_invoke_fn(PM_FPGA_LOAD, lower_32_bits(address),
-				   upper_32_bits(address), size, flags, NULL);
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	ret = zynqmp_pm_invoke_fn(PM_FPGA_LOAD, lower_32_bits(address),
+				  upper_32_bits(address), size, flags, 0,
+				  ret_payload);
+	*status = ret_payload[0];
+
+	return ret;
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_load);
 
@@ -804,7 +1039,8 @@
 	if (!value)
 		return -EINVAL;
 
-	ret = zynqmp_pm_invoke_fn(PM_FPGA_GET_STATUS, 0, 0, 0, 0, ret_payload);
+	ret = zynqmp_pm_invoke_fn(PM_FPGA_GET_STATUS, 0, 0, 0, 0, 0,
+				  ret_payload);
 	*value = ret_payload[1];
 
 	return ret;
@@ -812,6 +1048,57 @@
 EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_get_status);
 
 /**
+ * zynqmp_pm_fpga_get_version -Get xilfpga component version info
+ * @value: Value to read
+ *
+ * This function provides access to the pmufw to get the xilfpga
+ * component version info.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_fpga_get_version(u32 *value)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!value)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_FPGA_GET_VERSION, 0, 0, 0, 0, 0,
+				  ret_payload);
+	*value = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_get_version);
+
+/**
+ * zynqmp_pm_fpga_get_feature_list - Get xilfpga component supported feature
+ * list.
+ * @value: Value to read
+ *
+ * This function provides access to the pmufw to get the xilfpga component
+ * supported feature list.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_fpga_get_feature_list(u32 *value)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!value)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_FPGA_GET_FEATURE_LIST, 0, 0, 0, 0, 0,
+				  ret_payload);
+	*value = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_get_feature_list);
+
+/**
  * zynqmp_pm_pinctrl_request - Request Pin from firmware
  * @pin: Pin number to request
  *
@@ -821,7 +1108,7 @@
  */
 int zynqmp_pm_pinctrl_request(const u32 pin)
 {
-	return zynqmp_pm_invoke_fn(PM_PINCTRL_REQUEST, pin, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_PINCTRL_REQUEST, pin, 0, 0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_pinctrl_request);
 
@@ -835,7 +1122,7 @@
  */
 int zynqmp_pm_pinctrl_release(const u32 pin)
 {
-	return zynqmp_pm_invoke_fn(PM_PINCTRL_RELEASE, pin, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_PINCTRL_RELEASE, pin, 0, 0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_pinctrl_release);
 
@@ -857,7 +1144,7 @@
 		return -EINVAL;
 
 	ret = zynqmp_pm_invoke_fn(PM_PINCTRL_GET_FUNCTION, pin, 0,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*id = ret_payload[1];
 
 	return ret;
@@ -876,7 +1163,7 @@
 int zynqmp_pm_pinctrl_set_function(const u32 pin, const u32 id)
 {
 	return zynqmp_pm_invoke_fn(PM_PINCTRL_SET_FUNCTION, pin, id,
-				   0, 0, NULL);
+				   0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_pinctrl_set_function);
 
@@ -900,7 +1187,7 @@
 		return -EINVAL;
 
 	ret = zynqmp_pm_invoke_fn(PM_PINCTRL_CONFIG_PARAM_GET, pin, param,
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*value = ret_payload[1];
 
 	return ret;
@@ -921,7 +1208,7 @@
 				 u32 value)
 {
 	return zynqmp_pm_invoke_fn(PM_PINCTRL_CONFIG_PARAM_SET, pin,
-				   param, value, 0, NULL);
+				   param, value, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_pinctrl_set_config);
 
@@ -936,11 +1223,516 @@
  */
 int zynqmp_pm_init_finalize(void)
 {
-	return zynqmp_pm_invoke_fn(PM_PM_INIT_FINALIZE, 0, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_PM_INIT_FINALIZE, 0, 0, 0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_init_finalize);
 
 /**
+ * zynqmp_pm_write_aes_key - Write AES key registers
+ * @keylen:	Size of the input key to be written
+ * @keysrc:	Key Source to be selected to which provided
+ *			key should be updated
+ * @keyaddr: Address of a buffer which should contain the key
+ *			to be written
+ *
+ * This function provides support to write AES volatile user keys.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_write_aes_key(const u32 keylen, const u32 keysrc,
+			    const u64 keyaddr)
+{
+	return zynqmp_pm_invoke_fn(PM_WRITE_AES_KEY, keylen, keysrc,
+				   lower_32_bits(keyaddr),
+				   upper_32_bits(keyaddr), 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_write_aes_key);
+
+/**
+ * zynqmp_pm_bbram_write_aeskey - Write AES key in BBRAM
+ * @keylen:	Size of the input key to be written
+ * @keyaddr: Address of a buffer which should contain the key
+ *			to be written
+ *
+ * This function provides support to write AES keys into BBRAM.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bbram_write_aeskey(u32 keylen, const u64 keyaddr)
+{
+	return zynqmp_pm_invoke_fn(PM_BBRAM_WRITE_KEY, keylen,
+				   lower_32_bits(keyaddr),
+				   upper_32_bits(keyaddr), 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bbram_write_aeskey);
+
+/**
+ * zynqmp_pm_bbram_write_usrdata - Write user data in BBRAM
+ * @data: User data to be written in BBRAM
+ *
+ * This function provides support to write user data into BBRAM.
+ * The size of the user data must be 4 bytes.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bbram_write_usrdata(u32 data)
+{
+	return zynqmp_pm_invoke_fn(PM_BBRAM_WRITE_USERDATA, data, 0, 0, 0, 0,
+				   NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bbram_write_usrdata);
+
+/**
+ * zynqmp_pm_bbram_read_usrdata - Read user data in BBRAM
+ * @outaddr: Address of a buffer to store the user data read from BBRAM
+ *
+ * This function provides support to read user data in BBRAM.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bbram_read_usrdata(const u64 outaddr)
+{
+	return zynqmp_pm_invoke_fn(PM_BBRAM_READ_USERDATA, outaddr, 0, 0, 0, 0,
+				   NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bbram_read_usrdata);
+
+/**
+ * zynqmp_pm_bbram_zeroize - Zeroizes AES key in BBRAM
+ *
+ * Description:
+ * This function provides support to zeroize AES key in BBRAM.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bbram_zeroize(void)
+{
+	return zynqmp_pm_invoke_fn(PM_BBRAM_ZEROIZE, 0, 0, 0, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bbram_zeroize);
+
+/**
+ * zynqmp_pm_bbram_lock_userdata - Locks user data for write
+ *
+ * Description:
+ * This function disables writing user data into BBRAM.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bbram_lock_userdata(void)
+{
+	return zynqmp_pm_invoke_fn(PM_BBRAM_LOCK_USERDATA, 0, 0, 0, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bbram_lock_userdata);
+
+/**
+ * zynqmp_pm_get_uid_info - It is used to get image Info List
+ * @address:	Buffer address
+ * @size:	Number of bytes required to read from the firmware.
+ * @count:	Number of bytes read from the firmware.
+ *
+ * This function provides support to used to get image Info List
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_get_uid_info(const u64 address, const u32 size, u32 *count)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!count)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_GET_UID_INFO_LIST,
+				  upper_32_bits(address),
+				  lower_32_bits(address),
+				  size, 0, 0, ret_payload);
+
+	*count = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_uid_info);
+
+/**
+ * zynqmp_pm_get_meta_header - It is used to get image meta header Info
+ * @src:	PDI Image source buffer address.
+ * @dst:	Meta-header destination buffer address
+ * @size:	Size of the PDI image.
+ * @count:	Number of bytes read from the firmware.
+ *
+ * This function provides a support to get the image meta header Info
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_get_meta_header(const u64 src, const u64 dst,
+			      const u32 size, u32 *count)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!count)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_GET_META_HEADER_INFO_LIST,
+				  upper_32_bits(src), lower_32_bits(src),
+				  upper_32_bits(dst), lower_32_bits(dst),
+				  size, ret_payload);
+
+	*count = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_meta_header);
+
+/**
+ * zynqmp_pm_fpga_read - Perform the fpga configuration readback
+ * @reg_numframes: Configuration register offset (or) Number of frames to read
+ * @phys_address: Physical Address of the buffer
+ * @readback_type: Type of fpga readback operation
+ * @value: Value to read
+ *
+ * This function provides access to xilfpga library to perform
+ * fpga configuration readback.
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_fpga_read(const u32 reg_numframes, const u64 phys_address,
+			u32 readback_type, u32 *value)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!value)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_FPGA_READ, reg_numframes,
+				  lower_32_bits(phys_address),
+				  upper_32_bits(phys_address), readback_type,
+				  0, ret_payload);
+	*value = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_read);
+
+/**
+ * zynqmp_pm_sha_hash - Access the SHA engine to calculate the hash
+ * @address:	Address of the data/ Address of output buffer where
+ *		hash should be stored.
+ * @size:	Size of the data.
+ * @flags:
+ *	BIT(0) - for initializing csudma driver and SHA3(Here address
+ *		 and size inputs can be NULL).
+ *	BIT(1) - to call Sha3_Update API which can be called multiple
+ *		 times when data is not contiguous.
+ *	BIT(2) - to get final hash of the whole updated data.
+ *		 Hash will be overwritten at provided address with
+ *		 48 bytes.
+ *
+ * Return:	Returns status, either success or error code.
+ */
+int zynqmp_pm_sha_hash(const u64 address, const u32 size, const u32 flags)
+{
+	u32 lower_addr = lower_32_bits(address);
+	u32 upper_addr = upper_32_bits(address);
+
+	return zynqmp_pm_invoke_fn(PM_SECURE_SHA, upper_addr, lower_addr,
+				   size, flags, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_sha_hash);
+
+/**
+ * zynqmp_pm_rsa - Access RSA hardware to encrypt/decrypt the data with RSA.
+ * @address:	Address of the data
+ * @size:	Size of the data.
+ * @flags:
+ *		BIT(0) - Encryption/Decryption
+ *			 0 - RSA decryption with private key
+ *			 1 - RSA encryption with public key.
+ *
+ * Return:	Returns status, either success or error code.
+ */
+int zynqmp_pm_rsa(const u64 address, const u32 size, const u32 flags)
+{
+	u32 lower_32_bits = (u32)address;
+	u32 upper_32_bits = (u32)(address >> 32);
+
+	return zynqmp_pm_invoke_fn(PM_SECURE_RSA, upper_32_bits, lower_32_bits,
+				   size, flags, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_rsa);
+
+/**
+ * zynqmp_pm_request_suspend - PM call to request for another PU or subsystem to
+ *					be suspended gracefully.
+ * @node:	Node ID of the targeted PU or subsystem
+ * @ack:	Flag to specify whether acknowledge is requested
+ * @latency:	Requested wakeup latency (not supported)
+ * @state:	Requested state (not supported)
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_request_suspend(const u32 node,
+			      const enum zynqmp_pm_request_ack ack,
+			      const u32 latency, const u32 state)
+{
+	return zynqmp_pm_invoke_fn(PM_REQUEST_SUSPEND, node, ack,
+				   latency, state, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_request_suspend);
+
+/**
+ * zynqmp_pm_force_powerdown - PM call to request for another PU or subsystem to
+ *				be powered down forcefully
+ * @target:	Node ID of the targeted PU or subsystem
+ * @ack:	Flag to specify whether acknowledge is requested
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_force_powerdown(const u32 target,
+			      const enum zynqmp_pm_request_ack ack)
+{
+	return zynqmp_pm_invoke_fn(PM_FORCE_POWERDOWN, target, ack, 0, 0,
+				   0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_force_powerdown);
+
+/**
+ * zynqmp_pm_request_wakeup - PM call to wake up selected master or subsystem
+ * @node:	Node ID of the master or subsystem
+ * @set_addr:	Specifies whether the address argument is relevant
+ * @address:	Address from which to resume when woken up
+ * @ack:	Flag to specify whether acknowledge requested
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_request_wakeup(const u32 node, const bool set_addr,
+			     const u64 address,
+			     const enum zynqmp_pm_request_ack ack)
+{
+	/* set_addr flag is encoded into 1st bit of address */
+	return zynqmp_pm_invoke_fn(PM_REQUEST_WAKEUP, node, address | set_addr,
+				   address >> 32, ack, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_request_wakeup);
+
+/**
+ * zynqmp_pm_set_wakeup_source - PM call to specify the wakeup source
+ *					while suspended
+ * @target:	Node ID of the targeted PU or subsystem
+ * @wakeup_node:Node ID of the wakeup peripheral
+ * @enable:	Enable or disable the specified peripheral as wake source
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_set_wakeup_source(const u32 target, const u32 wakeup_node,
+				const u32 enable)
+{
+	return zynqmp_pm_invoke_fn(PM_SET_WAKEUP_SOURCE, target,
+				   wakeup_node, enable, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_wakeup_source);
+
+/**
+ * zynqmp_pm_set_max_latency - PM call to set wakeup latency requirements
+ * @node:	Node ID of the slave
+ * @latency:	Requested maximum wakeup latency
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_set_max_latency(const u32 node, const u32 latency)
+{
+	return zynqmp_pm_invoke_fn(PM_SET_MAX_LATENCY, node, latency,
+				   0, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_max_latency);
+
+/**
+ * zynqmp_pm_set_configuration - PM call to set system configuration
+ * @physical_addr:	Physical 32-bit address of data structure in memory
+ *
+ * Return:		Returns status, either success or error+reason
+ */
+int zynqmp_pm_set_configuration(const u32 physical_addr)
+{
+	return zynqmp_pm_invoke_fn(PM_SET_CONFIGURATION, physical_addr, 0,
+				   0, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_configuration);
+
+/**
+ * zynqmp_pm_get_node_status - PM call to request a node's current power state
+ * @node:		ID of the component or sub-system in question
+ * @status:		Current operating state of the requested node
+ * @requirements:	Current requirements asserted on the node,
+ *			used for slave nodes only.
+ * @usage:		Usage information, used for slave nodes only:
+ *			PM_USAGE_NO_MASTER	- No master is currently using
+ *						  the node
+ *			PM_USAGE_CURRENT_MASTER	- Only requesting master is
+ *						  currently using the node
+ *			PM_USAGE_OTHER_MASTER	- Only other masters are
+ *						  currently using the node
+ *			PM_USAGE_BOTH_MASTERS	- Both the current and at least
+ *						  one other master is currently
+ *						  using the node
+ *
+ * Return:		Returns status, either success or error+reason
+ */
+int zynqmp_pm_get_node_status(const u32 node, u32 *const status,
+			      u32 *const requirements, u32 *const usage)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!status)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_GET_NODE_STATUS, node, 0, 0,
+				  0, 0, ret_payload);
+	if (ret_payload[0] == XST_PM_SUCCESS) {
+		*status = ret_payload[1];
+		if (requirements)
+			*requirements = ret_payload[2];
+		if (usage)
+			*usage = ret_payload[3];
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_node_status);
+
+/**
+ * zynqmp_pm_get_operating_characteristic - PM call to request operating
+ *						characteristic information
+ * @node:	Node ID of the slave
+ * @type:	Type of the operating characteristic requested
+ * @result:	Used to return the requested operating characteristic
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_get_operating_characteristic(const u32 node,
+					   const enum zynqmp_pm_opchar_type type,
+					   u32 *const result)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!result)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_GET_OPERATING_CHARACTERISTIC,
+				  node, type, 0, 0, 0, ret_payload);
+	if (ret_payload[0] == XST_PM_SUCCESS)
+		*result = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_operating_characteristic);
+
+/**
+ * zynqmp_pm_config_reg_access - PM Config API for Config register access
+ * @register_access_id:	ID of the requested REGISTER_ACCESS
+ * @address:		Address of the register to be accessed
+ * @mask:		Mask to be written to the register
+ * @value:		Value to be written to the register
+ * @out:		Returned output value
+ *
+ * This function calls REGISTER_ACCESS to configure CSU/PMU registers.
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_config_reg_access(u32 register_access_id, u32 address,
+				u32 mask, u32 value, u32 *out)
+{
+	return zynqmp_pm_invoke_fn(PM_REGISTER_ACCESS, register_access_id,
+				   address, mask, value, 0, out);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_config_reg_access);
+
+/**
+ * zynqmp_pm_mmio_read - Provide access to register read.
+ * @address:	Address of the register to be accessed
+ * @out:	Returned output value
+ *
+ * This function calls MMIO_READ to read the register.
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+
+int zynqmp_pm_mmio_read(u32 address, u32 *out)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	ret = zynqmp_pm_invoke_fn(PM_MMIO_READ, address, 0, 0, 0, 0,
+				  ret_payload);
+	*out = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_mmio_read);
+
+/**
+ * zynqmp_pm_mmio_write - Provide access to register write.
+ * @address:	Address of the register to be accessed
+ * @mask:	Mask to be written to the register
+ * @value:	Value to be written to the register
+ *
+ * This function calls MMIO_WRITE to write the register.
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+
+int zynqmp_pm_mmio_write(u32 address, u32 mask, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_MMIO_WRITE, address, mask,
+				   value, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_mmio_write);
+
+/**
+ * zynqmp_pm_bootmode_read() - PM Config API for read bootpin status
+ * @ps_mode: Returned output value of ps_mode
+ *
+ * This API function is to be used for notify the power management controller
+ * to read bootpin status.
+ *
+ * Return: status, either success or error+reason
+ */
+unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode)
+{
+	unsigned int ret;
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+
+	ret = zynqmp_pm_invoke_fn(PM_MMIO_READ, CRL_APB_BOOT_PIN_CTRL, 0,
+				  0, 0, 0, ret_payload);
+
+	*ps_mode = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bootmode_read);
+
+/**
+ * zynqmp_pm_bootmode_write() - PM Config API for Configure bootpin
+ * @ps_mode: Value to be written to the bootpin ctrl register
+ *
+ * This API function is to be used for notify the power management controller
+ * to configure bootpin.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bootmode_write(u32 ps_mode)
+{
+	return zynqmp_pm_invoke_fn(PM_MMIO_WRITE, CRL_APB_BOOT_PIN_CTRL,
+				   CRL_APB_BOOTPIN_CTRL_MASK, ps_mode, 0,
+				   0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bootmode_write);
+
+/**
  * zynqmp_pm_set_suspend_mode()	- Set system suspend mode
  * @mode:	Mode to set for system suspend
  *
@@ -950,7 +1742,7 @@
  */
 int zynqmp_pm_set_suspend_mode(u32 mode)
 {
-	return zynqmp_pm_invoke_fn(PM_SET_SUSPEND_MODE, mode, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_SET_SUSPEND_MODE, mode, 0, 0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_set_suspend_mode);
 
@@ -970,7 +1762,7 @@
 			   const u32 qos, const enum zynqmp_pm_request_ack ack)
 {
 	return zynqmp_pm_invoke_fn(PM_REQUEST_NODE, node, capabilities,
-				   qos, ack, NULL);
+				   qos, ack, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_request_node);
 
@@ -986,11 +1778,110 @@
  */
 int zynqmp_pm_release_node(const u32 node)
 {
-	return zynqmp_pm_invoke_fn(PM_RELEASE_NODE, node, 0, 0, 0, NULL);
+	return zynqmp_pm_invoke_fn(PM_RELEASE_NODE, node, 0, 0, 0, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_release_node);
 
 /**
+ * zynqmp_pm_get_rpu_mode() - Get RPU mode
+ * @node_id:	Node ID of the device
+ * @rpu_mode:	return by reference value
+ *		either split or lockstep
+ *
+ * Return:	return 0 on success or error+reason.
+ *		if success, then  rpu_mode will be set
+ *		to current rpu mode.
+ */
+int zynqmp_pm_get_rpu_mode(u32 node_id, enum rpu_oper_mode *rpu_mode)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	ret = zynqmp_pm_invoke_fn(PM_IOCTL, node_id,
+				  IOCTL_GET_RPU_OPER_MODE, 0, 0, 0,
+				  ret_payload);
+
+	/* only set rpu_mode if no error */
+	if (ret == XST_PM_SUCCESS)
+		*rpu_mode = ret_payload[0];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_rpu_mode);
+
+/**
+ * zynqmp_pm_set_rpu_mode() - Set RPU mode
+ * @node_id:	Node ID of the device
+ * @rpu_mode:	Argument 1 to requested IOCTL call. either split or lockstep
+ *
+ *		This function is used to set RPU mode to split or
+ *		lockstep
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+int zynqmp_pm_set_rpu_mode(u32 node_id, enum rpu_oper_mode rpu_mode)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node_id,
+				   IOCTL_SET_RPU_OPER_MODE, (u32)rpu_mode,
+				   0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_rpu_mode);
+
+/**
+ * zynqmp_pm_set_tcm_config - configure TCM
+ * @node_id:	Node ID of the device
+ * @tcm_mode:	Argument 1 to requested IOCTL call
+ *              either PM_RPU_TCM_COMB or PM_RPU_TCM_SPLIT
+ *
+ * This function is used to set RPU mode to split or combined
+ *
+ * Return: status: 0 for success, else failure
+ */
+int zynqmp_pm_set_tcm_config(u32 node_id, enum rpu_tcm_comb tcm_mode)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node_id,
+				   IOCTL_TCM_COMB_CONFIG, (u32)tcm_mode, 0,
+				   0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_tcm_config);
+
+/**
+ * zynqmp_pm_force_pwrdwn - PM call to request for another PU or subsystem to
+ *             be powered down forcefully
+ * @node:  Node ID of the targeted PU or subsystem
+ * @ack:   Flag to specify whether acknowledge is requested
+ *
+ * Return: status, either success or error+reason
+ */
+int zynqmp_pm_force_pwrdwn(const u32 node,
+			   const enum zynqmp_pm_request_ack ack)
+{
+	return zynqmp_pm_invoke_fn(PM_FORCE_POWERDOWN, node, ack, 0, 0, 0,
+				   NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_force_pwrdwn);
+
+/**
+ * zynqmp_pm_request_wake - PM call to wake up selected master or subsystem
+ * @node:  Node ID of the master or subsystem
+ * @set_addr:  Specifies whether the address argument is relevant
+ * @address:   Address from which to resume when woken up
+ * @ack:   Flag to specify whether acknowledge requested
+ *
+ * Return: status, either success or error+reason
+ */
+int zynqmp_pm_request_wake(const u32 node,
+			   const bool set_addr,
+			   const u64 address,
+			   const enum zynqmp_pm_request_ack ack)
+{
+	/* set_addr flag is encoded into 1st bit of address */
+	return zynqmp_pm_invoke_fn(PM_REQUEST_WAKEUP, node, address | set_addr,
+				   address >> 32, ack, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_request_wake);
+
+/**
  * zynqmp_pm_set_requirement() - PM call to set requirement for PM slaves
  * @node:		Node ID of the slave
  * @capabilities:	Requested capabilities of the slave
@@ -1007,14 +1898,14 @@
 			      const enum zynqmp_pm_request_ack ack)
 {
 	return zynqmp_pm_invoke_fn(PM_SET_REQUIREMENT, node, capabilities,
-				   qos, ack, NULL);
+				   qos, ack, 0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_set_requirement);
 
 /**
  * zynqmp_pm_load_pdi - Load and process PDI
- * @src:       Source device where PDI is located
- * @address:   PDI src address
+ * @src:	Source device where PDI is located
+ * @address:	PDI src address
  *
  * This function provides support to load PDI from linux
  *
@@ -1024,7 +1915,8 @@
 {
 	return zynqmp_pm_invoke_fn(PM_LOAD_PDI, src,
 				   lower_32_bits(address),
-				   upper_32_bits(address), 0, NULL);
+				   upper_32_bits(address), 0,
+				   0, NULL);
 }
 EXPORT_SYMBOL_GPL(zynqmp_pm_load_pdi);
 
@@ -1046,7 +1938,7 @@
 
 	ret = zynqmp_pm_invoke_fn(PM_SECURE_AES, upper_32_bits(address),
 				  lower_32_bits(address),
-				  0, 0, ret_payload);
+				  0, 0, 0, ret_payload);
 	*out = ret_payload[1];
 
 	return ret;
@@ -1054,6 +1946,73 @@
 EXPORT_SYMBOL_GPL(zynqmp_pm_aes_engine);
 
 /**
+ * zynqmp_pm_efuse_access - Provides access to efuse memory.
+ * @address:	Address of the efuse params structure
+ * @out:		Returned output value
+ *
+ * Return:	Returns status, either success or error code.
+ */
+int zynqmp_pm_efuse_access(const u64 address, u32 *out)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!out)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_EFUSE_ACCESS, upper_32_bits(address),
+				  lower_32_bits(address), 0, 0, 0,
+				  ret_payload);
+	*out = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_efuse_access);
+
+int zynqmp_pm_secure_load(const u64 src_addr, u64 key_addr, u64 *dst)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret_value;
+
+	if (!dst)
+		return -EINVAL;
+
+	ret_value = zynqmp_pm_invoke_fn(PM_SECURE_IMAGE,
+					lower_32_bits(src_addr),
+					upper_32_bits(src_addr),
+					lower_32_bits(key_addr),
+					upper_32_bits(key_addr),
+					0, ret_payload);
+	*dst = ((u64)ret_payload[1] << 32) | ret_payload[2];
+
+	return ret_value;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_secure_load);
+
+/**
+ * zynqmp_pm_register_notifier() - PM API for register a subsystem
+ *                                to be notified about specific
+ *                                event/error.
+ * @node:	Node ID to which the event is related.
+ * @event:	Event Mask of Error events for which wants to get notified.
+ * @wake:	Wake subsystem upon capturing the event if value 1
+ * @enable:	Enable the registration for value 1, disable for value 0
+ *
+ * This function is used to register/un-register for particular node-event
+ * combination in firmware.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+
+int zynqmp_pm_register_notifier(const u32 node, const u32 event,
+				const u32 wake, const u32 enable)
+{
+	return zynqmp_pm_invoke_fn(PM_REGISTER_NOTIFIER, node, event,
+				   wake, enable, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_register_notifier);
+
+/**
  * zynqmp_pm_system_shutdown - PM call to request a system shutdown or restart
  * @type:	Shutdown or restart? 0 for shutdown, 1 for restart
  * @subtype:	Specifies which system should be restarted or shut down
@@ -1063,8 +2022,153 @@
 int zynqmp_pm_system_shutdown(const u32 type, const u32 subtype)
 {
 	return zynqmp_pm_invoke_fn(PM_SYSTEM_SHUTDOWN, type, subtype,
-				   0, 0, NULL);
+				   0, 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_set_feature_config - PM call to request IOCTL for feature config
+ * @id:         The config ID of the feature to be configured
+ * @value:      The config value of the feature to be configured
+ *
+ * Return:      Returns 0 on success or error value on failure.
+ */
+int zynqmp_pm_set_feature_config(enum pm_feature_config_id id, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_SET_FEATURE_CONFIG,
+				   id, value, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_get_feature_config - PM call to get value of configured feature
+ * @id:         The config id of the feature to be queried
+ * @payload:    Returned value array
+ *
+ * Return:      Returns 0 on success or error value on failure.
+ */
+int zynqmp_pm_get_feature_config(enum pm_feature_config_id id,
+				 u32 *payload)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, 0, IOCTL_GET_FEATURE_CONFIG,
+				   id, 0, 0, payload);
+}
+
+/**
+ * zynqmp_pm_sec_read_reg - PM call to securely read from given offset
+ *		of the node
+ * @node_id:	Node Id of the device
+ * @offset:	Offset to be used (20-bit)
+ * @ret_value:	Output data read from the given offset after
+ *		firmware access policy is successfully enforced
+ *
+ * Return:	Returns 0 on success or error value on failure
+ */
+int zynqmp_pm_sec_read_reg(u32 node_id, u32 offset, u32 *ret_value)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	u32 count = 1;
+	int ret;
+
+	if (!ret_value)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_IOCTL, node_id, IOCTL_READ_REG, offset,
+				  count, 0, ret_payload);
+
+	*ret_value = ret_payload[1];
+
+	return ret;
+}
+
+/**
+ * zynqmp_pm_sec_mask_write_reg - PM call to securely write to given offset
+ *		of the node
+ * @node_id:	Node Id of the device
+ * @offset:	Offset to be used (20-bit)
+ * @mask:	Mask to be used
+ * @value:	Value to be written
+ *
+ * Return:	Returns 0 on success or error value on failure
+ */
+int zynqmp_pm_sec_mask_write_reg(const u32 node_id, const u32 offset, u32 mask,
+				 u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node_id, IOCTL_MASK_WRITE_REG,
+				   offset, mask, value, NULL);
+}
+
+/**
+ * zynqmp_pm_get_qos - PM call to query default and current QoS of the node
+ * @node:	Node Id of the device
+ * @def_qos:	Default QoS value
+ * @qos:	Current QoS value
+ *
+ * Return:	Returns 0 on success and the default and current QoS registers in
+ *		@def_qos and @qos or error value on failure
+ */
+int zynqmp_pm_get_qos(u32 node, u32 *const def_qos, u32 *const qos)
+{
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+	int ret;
+
+	if (!def_qos || !qos)
+		return -EINVAL;
+
+	ret = zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_GET_QOS, 0, 0, 0,
+				  ret_payload);
+
+	*def_qos = ret_payload[1];
+	*qos = ret_payload[2];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_qos);
+
+/**
+ * zynqmp_pm_set_sd_config - PM call to set value of SD config registers
+ * @node:	SD node ID
+ * @config:	The config type of SD registers
+ * @value:	Value to be set
+ *
+ * Return:      Returns 0 on success or error value on failure.
+ */
+int zynqmp_pm_set_sd_config(u32 node, enum pm_sd_config_type config, u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_SET_SD_CONFIG,
+				   config, value, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_sd_config);
+
+/**
+ * zynqmp_pm_set_gem_config - PM call to set value of GEM config registers
+ * @node:	GEM node ID
+ * @config:	The config type of GEM registers
+ * @value:	Value to be set
+ *
+ * Return:      Returns 0 on success or error value on failure.
+ */
+int zynqmp_pm_set_gem_config(u32 node, enum pm_gem_config_type config,
+			     u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_SET_GEM_CONFIG,
+				   config, value, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_gem_config);
+
+/**
+ * zynqmp_pm_set_usb_config - PM call to set value of USB config registers
+ * @node:	USB node ID
+ * @config:	The config type of USB registers
+ * @value:	Value to be set
+ *
+ * Return:      Returns 0 on success or error value on failure.
+ */
+int zynqmp_pm_set_usb_config(u32 node, enum pm_usb_config_type config,
+			     u32 value)
+{
+	return zynqmp_pm_invoke_fn(PM_IOCTL, node, IOCTL_SET_USB_CONFIG,
+				   config, value, 0, NULL);
 }
+EXPORT_SYMBOL_GPL(zynqmp_pm_set_usb_config);
 
 /**
  * struct zynqmp_pm_shutdown_scope - Struct for shutdown scope
@@ -1334,6 +2438,123 @@
 static DEVICE_ATTR_RW(pggs2);
 static DEVICE_ATTR_RW(pggs3);
 
+static ssize_t last_reset_reason_show(struct device *device,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	int ret;
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+
+	ret = zynqmp_pm_get_last_reset_reason(ret_payload);
+	if (ret)
+		return ret;
+	switch (ret_payload[1]) {
+	case PM_RESET_REASON_EXT_POR:
+		return sprintf(buf, "ext_por\n");
+	case PM_RESET_REASON_SW_POR:
+		return sprintf(buf, "sw_por\n");
+	case PM_RESET_REASON_SLR_POR:
+		return sprintf(buf, "sl_por\n");
+	case PM_RESET_REASON_ERR_POR:
+		return sprintf(buf, "err_por\n");
+	case PM_RESET_REASON_DAP_SRST:
+		return sprintf(buf, "dap_srst\n");
+	case PM_RESET_REASON_ERR_SRST:
+		return sprintf(buf, "err_srst\n");
+	case PM_RESET_REASON_SW_SRST:
+		return sprintf(buf, "sw_srst\n");
+	case PM_RESET_REASON_SLR_SRST:
+		return sprintf(buf, "slr_srst\n");
+	default:
+		return sprintf(buf, "unknown reset\n");
+	}
+}
+static DEVICE_ATTR_RO(last_reset_reason);
+
+static atomic_t feature_conf_id;
+
+static ssize_t feature_config_id_show(struct device *device,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	return sysfs_emit(buf, "%d\n", atomic_read(&feature_conf_id));
+}
+
+static ssize_t feature_config_id_store(struct device *device,
+				       struct device_attribute *attr,
+				       const char *buf, size_t count)
+{
+	u32 config_id;
+	int ret;
+
+	if (!buf)
+		return -EINVAL;
+
+	ret = kstrtou32(buf, 10, &config_id);
+	if (ret)
+		return ret;
+
+	atomic_set(&feature_conf_id, config_id);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(feature_config_id);
+
+static ssize_t feature_config_value_show(struct device *device,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	int ret;
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+
+	ret = zynqmp_pm_get_feature_config(atomic_read(&feature_conf_id),
+					   ret_payload);
+	if (ret)
+		return ret;
+
+	return sysfs_emit(buf, "%d\n", ret_payload[1]);
+}
+
+static ssize_t feature_config_value_store(struct device *device,
+					  struct device_attribute *attr,
+					  const char *buf, size_t count)
+{
+	u32 value;
+	int ret;
+
+	if (!buf)
+		return -EINVAL;
+
+	ret = kstrtou32(buf, 10, &value);
+	if (ret)
+		return ret;
+
+	ret = zynqmp_pm_set_feature_config(atomic_read(&feature_conf_id),
+					   value);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(feature_config_value);
+
+static ssize_t firmware_store(struct device *dev,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	unsigned int len;
+
+	len = strscpy(image_name, buf, NAME_MAX);
+	/* lose terminating \n */
+	if (image_name[len - 1] == '\n')
+		image_name[len - 1] = 0;
+
+	return count;
+}
+static DEVICE_ATTR_WO(firmware);
+
 static struct attribute *zynqmp_firmware_attrs[] = {
 	&dev_attr_ggs0.attr,
 	&dev_attr_ggs1.attr,
@@ -1345,17 +2566,264 @@
 	&dev_attr_pggs3.attr,
 	&dev_attr_shutdown_scope.attr,
 	&dev_attr_health_status.attr,
+	&dev_attr_last_reset_reason.attr,
+	&dev_attr_feature_config_id.attr,
+	&dev_attr_feature_config_value.attr,
+	&dev_attr_firmware.attr,
 	NULL,
 };
 
 ATTRIBUTE_GROUPS(zynqmp_firmware);
 
+/**
+ * config_reg_store - Write config_reg sysfs attribute
+ * @kobj:	Kobject structure
+ * @attr:	Kobject attribute structure
+ * @buf:	User entered health_status attribute string
+ * @count:	Buffer size
+ *
+ * User-space interface for setting the config register.
+ *
+ * To write any CSU/PMU register
+ * echo <address> <mask> <values> > /sys/firmware/zynqmp/config_reg
+ * Usage:
+ * echo 0x345AB234 0xFFFFFFFF 0x1234ABCD > /sys/firmware/zynqmp/config_reg
+ *
+ * To Read any CSU/PMU register, write address to the variable like below
+ * echo <address> > /sys/firmware/zynqmp/config_reg
+ *
+ * Return:	count argument if request succeeds, the corresponding error
+ *		code otherwise
+ */
+static ssize_t config_reg_store(struct kobject *kobj,
+				struct kobj_attribute *attr,
+				const char *buf, size_t count)
+{
+	char *kern_buff, *inbuf, *tok;
+	unsigned long address, value, mask;
+	int ret;
+
+	kern_buff = kzalloc(count, GFP_KERNEL);
+	if (!kern_buff)
+		return -ENOMEM;
+
+	ret = strlcpy(kern_buff, buf, count);
+	if (ret < 0) {
+		ret = -EFAULT;
+		goto err;
+	}
+
+	inbuf = kern_buff;
+
+	/* Read the addess */
+	tok = strsep(&inbuf, " ");
+	if (!tok) {
+		ret = -EFAULT;
+		goto err;
+	}
+	ret = kstrtol(tok, 16, &address);
+	if (ret) {
+		ret = -EFAULT;
+		goto err;
+	}
+	/* Read the write value */
+	tok = strsep(&inbuf, " ");
+	/*
+	 * If parameter provided is only address, then its a read operation.
+	 * Store the address in a global variable and retrieve whenever
+	 * required.
+	 */
+	if (!tok) {
+		register_address = address;
+		goto err;
+	}
+	register_address = address;
+
+	ret = kstrtol(tok, 16, &mask);
+	if (ret) {
+		ret = -EFAULT;
+		goto err;
+	}
+	tok = strsep(&inbuf, " ");
+	if (!tok) {
+		ret = -EFAULT;
+		goto err;
+	}
+	ret = kstrtol(tok, 16, &value);
+	if (ret) {
+		ret = -EFAULT;
+		goto err;
+	}
+	ret = zynqmp_pm_config_reg_access(CONFIG_REG_WRITE, address,
+					  mask, value, NULL);
+	if (ret)
+		pr_err("unable to write value to %lx\n", value);
+err:
+	kfree(kern_buff);
+	if (ret)
+		return ret;
+	return count;
+}
+
+/**
+ * config_reg_show - Read config_reg sysfs attribute
+ * @kobj:	Kobject structure
+ * @attr:	Kobject attribute structure
+ * @buf:	User entered health_status attribute string
+ *
+ * User-space interface for getting the config register.
+ *
+ * To Read any CSU/PMU register, write address to the variable like below
+ * echo <address> > /sys/firmware/zynqmp/config_reg
+ *
+ * Then Read the address using below command
+ * cat /sys/firmware/zynqmp/config_reg
+ *
+ * Return: number of chars written to buf.
+ */
+static ssize_t config_reg_show(struct kobject *kobj,
+			       struct kobj_attribute *attr,
+			       char *buf)
+{
+	int ret;
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+
+	ret = zynqmp_pm_config_reg_access(CONFIG_REG_READ, register_address,
+					  0, 0, ret_payload);
+	if (ret)
+		return ret;
+
+	return sprintf(buf, "0x%x\n", ret_payload[1]);
+}
+
+static struct kobj_attribute zynqmp_attr_config_reg =
+					__ATTR_RW(config_reg);
+
+static struct attribute *attrs[] = {
+	&zynqmp_attr_config_reg.attr,
+	NULL,
+};
+
+static const struct attribute_group attr_group = {
+	.attrs = attrs,
+	NULL,
+};
+
+static int zynqmp_pm_sysfs_init(void)
+{
+	struct kobject *zynqmp_kobj;
+	int ret;
+
+	zynqmp_kobj = kobject_create_and_add("zynqmp", firmware_kobj);
+	if (!zynqmp_kobj) {
+		pr_err("zynqmp: Firmware kobj add failed.\n");
+		return -ENOMEM;
+	}
+
+	ret = sysfs_create_group(zynqmp_kobj, &attr_group);
+	if (ret) {
+		pr_err("%s() sysfs creation fail with error %d\n",
+		       __func__, ret);
+	}
+
+	return ret;
+}
+
+static ssize_t firmware_uid_get_data(struct file *filp, struct kobject *kobj,
+				     struct bin_attribute *attr, char *buf,
+				     loff_t off, size_t count)
+{
+	struct device *kdev = kobj_to_dev(kobj);
+	dma_addr_t dma_addr = 0;
+	char *kbuf;
+	u32 size;
+	int ret;
+
+	kbuf = dma_alloc_coherent(kdev, UID_BUFF_SIZE, &dma_addr, GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	/* Read from the firmware memory */
+	ret = zynqmp_pm_get_uid_info(dma_addr, UID_BUFF_SIZE, &size);
+	if (ret) {
+		dma_free_coherent(kdev, UID_BUFF_SIZE, kbuf, dma_addr);
+		return ret;
+	}
+
+	size = size * UID_SET_LEN * UID_LEN;
+	memcpy(buf, kbuf, size);
+	dma_free_coherent(kdev, UID_BUFF_SIZE, kbuf, dma_addr);
+
+	return size;
+}
+
+static const struct bin_attribute uid_attr = {
+	.attr.name = "uid-read",
+	.attr.mode = 00400,
+	.size = 1,
+	.read = firmware_uid_get_data,
+};
+
+static ssize_t firmware_meta_header_get_data(struct file *filp,
+					     struct kobject *kobj,
+					     struct bin_attribute *attr,
+					     char *buf, loff_t off,
+					     size_t count)
+{
+	struct device *kdev = kobj_to_dev(kobj);
+	const struct firmware *fw;
+	dma_addr_t dma_addr = 0;
+	char *kbuf;
+	u32 size;
+	int ret;
+
+	ret = request_firmware(&fw, image_name, kdev);
+	if (ret) {
+		dev_err(kdev, "Error requesting firmware %s\n", image_name);
+		return ret;
+	}
+
+	kbuf = dma_alloc_coherent(kdev, fw->size, &dma_addr, GFP_KERNEL);
+	if (!kbuf) {
+		ret = -ENOMEM;
+		goto free_firmware;
+	}
+
+	memcpy(kbuf, fw->data, fw->size);
+
+	/* Read from the firmware memory */
+	ret = zynqmp_pm_get_meta_header(dma_addr, dma_addr, fw->size, &size);
+	if (ret)
+		goto free_dma;
+
+	memcpy(buf, kbuf, size);
+	ret = size;
+
+free_dma:
+	dma_free_coherent(kdev, fw->size, kbuf, dma_addr);
+free_firmware:
+	release_firmware(fw);
+
+	return ret;
+}
+
+static const struct bin_attribute meta_header_attr = {
+	.attr.name = "meta-header-read",
+	.attr.mode = 00400,
+	.size = 1,
+	.read = firmware_meta_header_get_data,
+};
+
 static int zynqmp_firmware_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np;
 	int ret;
 
+	ret = get_set_conduit_method(dev->of_node);
+	if (ret)
+		return ret;
+
 	np = of_find_compatible_node(NULL, NULL, "xlnx,zynqmp");
 	if (!np) {
 		np = of_find_compatible_node(NULL, NULL, "xlnx,versal");
@@ -1364,14 +2832,20 @@
 
 		feature_check_enabled = true;
 	}
+
+	if (!feature_check_enabled) {
+		ret = do_feature_check_call(PM_FEATURE_CHECK);
+		if (ret >= 0)
+			feature_check_enabled = true;
+	}
+
 	of_node_put(np);
 
-	ret = get_set_conduit_method(dev->of_node);
+	/* Check PM API version number */
+	ret = zynqmp_pm_get_api_version(&pm_api_version);
 	if (ret)
 		return ret;
 
-	/* Check PM API version number */
-	zynqmp_pm_get_api_version(&pm_api_version);
 	if (pm_api_version < ZYNQMP_PM_VERSION) {
 		panic("%s Platform Management API version error. Expected: v%d.%d - Found: v%d.%d\n",
 		      __func__,
@@ -1403,8 +2877,43 @@
 		return ret;
 	}
 
+	ret = zynqmp_pm_sysfs_init();
+	if (ret) {
+		pr_err("%s() sysfs init fail with error %d\n", __func__, ret);
+		return ret;
+	}
+
+	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret < 0) {
+		dev_err(dev, "no usable DMA configuration");
+		return ret;
+	}
+
+	ret = sysfs_create_bin_file(&pdev->dev.kobj, &uid_attr);
+	if (ret) {
+		pr_err("%s() Failed to create sysfs binary file for uid-read with error%d\n",
+		       __func__, ret);
+		return ret;
+	}
+
+	ret = sysfs_create_bin_file(&pdev->dev.kobj, &meta_header_attr);
+	if (ret) {
+		dev_err(dev, "%s() Failed to create sysfs binary file for meta-header-read with error%d\n",
+			__func__, ret);
+		return ret;
+	}
+
 	zynqmp_pm_api_debugfs_init();
 
+	np = of_find_compatible_node(NULL, NULL, "xlnx,versal");
+	if (np) {
+		em_dev = platform_device_register_data(&pdev->dev, "xlnx_event_manager",
+						       -1, NULL, 0);
+		if (IS_ERR(em_dev))
+			dev_err_probe(&pdev->dev, PTR_ERR(em_dev), "EM register fail with error\n");
+	}
+	of_node_put(np);
+
 	return of_platform_populate(dev->of_node, NULL, NULL, dev);
 }
 
@@ -1422,6 +2931,8 @@
 		kfree(feature_data);
 	}
 
+	platform_device_unregister(em_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/Kconfig
@@ -12,6 +12,16 @@
 
 if FPGA
 
+config FPGA_MGR_DEBUG_FS
+	tristate "FPGA debug fs"
+	select DEBUG_FS
+	help
+	  Say Y here if you want to expose a DebugFS interface for the
+	  FPGA Manager Framework. FPGA manager DebugFS provides a user
+	  interface to read the fpga specific configuration information.
+
+	  If unsure, say N.
+
 config FPGA_MGR_SOCFPGA
 	tristate "Altera SOCFPGA FPGA Manager"
 	depends on ARCH_INTEL_SOCFPGA || COMPILE_TEST
@@ -91,6 +101,24 @@
 	  FPGA manager driver support for the Altera Cyclone II FPGA
 	  present on the TS-73xx SBC boards.
 
+config FPGA_MGR_ZYNQ_AFI_FPGA
+	bool "Xilinx AFI FPGA"
+	depends on FPGA_MGR_ZYNQ_FPGA
+	help
+	  Zynq AFI driver support for writing to the AFI registers
+	  for configuring the PS_PL interface. For some of the bitstream
+	  or designs to work the PS to PL interfaces need to be configured
+	  like the data bus-width etc.
+
+config XILINX_AFI_FPGA
+	bool "Xilinx AFI FPGA"
+	depends on FPGA_MGR_ZYNQMP_FPGA || COMPILE_TEST
+	help
+	  FPGA manager driver support for writing to the AFI registers
+	  for configuring the PS_PL interface. For some of the bitstream
+	  or designs to work the PS to PL interfaces need to be configured
+	  like the datawidth etc.
+
 config FPGA_BRIDGE
 	tristate "FPGA Bridge Framework"
 	help
@@ -115,8 +143,8 @@
 
 config XILINX_PR_DECOUPLER
 	tristate "Xilinx LogiCORE PR Decoupler"
-	depends on FPGA_BRIDGE
 	depends on HAS_IOMEM
+	select FPGA_BRIDGE
 	help
 	  Say Y to enable drivers for Xilinx LogiCORE PR Decoupler
 	  or Xilinx Dynamic Function eXchange AIX Shutdown Manager.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/Makefile
@@ -17,8 +17,10 @@
 obj-$(CONFIG_FPGA_MGR_TS73XX)		+= ts73xx-fpga.o
 obj-$(CONFIG_FPGA_MGR_XILINX_SPI)	+= xilinx-spi.o
 obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
+obj-$(CONFIG_FPGA_MGR_ZYNQ_AFI_FPGA)	+= zynq-afi.o
 obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA)	+= zynqmp-fpga.o
-obj-$(CONFIG_FPGA_MGR_VERSAL_FPGA)      += versal-fpga.o
+obj-$(CONFIG_FPGA_MGR_VERSAL_FPGA)	+= versal-fpga.o
+obj-$(CONFIG_XILINX_AFI_FPGA)		+= xilinx-afi.o
 obj-$(CONFIG_ALTERA_PR_IP_CORE)         += altera-pr-ip-core.o
 obj-$(CONFIG_ALTERA_PR_IP_CORE_PLAT)    += altera-pr-ip-core-plat.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/altera-pr-ip-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/altera-pr-ip-core.c
@@ -108,7 +108,7 @@
 	u32 *buffer_32 = (u32 *)buf;
 	size_t i = 0;
 
-	if (count <= 0)
+	if (!count)
 		return -EINVAL;
 
 	/* Write out the complete 32-bit chunks */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/dfl-fme-region.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/dfl-fme-region.c
@@ -30,6 +30,7 @@
 static int fme_region_probe(struct platform_device *pdev)
 {
 	struct dfl_fme_region_pdata *pdata = dev_get_platdata(&pdev->dev);
+	struct fpga_region_info info = { 0 };
 	struct device *dev = &pdev->dev;
 	struct fpga_region *region;
 	struct fpga_manager *mgr;
@@ -39,20 +40,18 @@
 	if (IS_ERR(mgr))
 		return -EPROBE_DEFER;
 
-	region = devm_fpga_region_create(dev, mgr, fme_region_get_bridges);
-	if (!region) {
-		ret = -ENOMEM;
+	info.mgr = mgr;
+	info.compat_id = mgr->compat_id;
+	info.get_bridges = fme_region_get_bridges;
+	info.priv = pdata;
+	region = fpga_region_register_full(dev, &info);
+	if (IS_ERR(region)) {
+		ret = PTR_ERR(region);
 		goto eprobe_mgr_put;
 	}
 
-	region->priv = pdata;
-	region->compat_id = mgr->compat_id;
 	platform_set_drvdata(pdev, region);
 
-	ret = fpga_region_register(region);
-	if (ret)
-		goto eprobe_mgr_put;
-
 	dev_dbg(dev, "DFL FME FPGA Region probed\n");
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/dfl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/dfl.c
@@ -1407,19 +1407,15 @@
 	if (!cdev)
 		return ERR_PTR(-ENOMEM);
 
-	cdev->region = devm_fpga_region_create(info->dev, NULL, NULL);
-	if (!cdev->region) {
-		ret = -ENOMEM;
-		goto free_cdev_exit;
-	}
-
 	cdev->parent = info->dev;
 	mutex_init(&cdev->lock);
 	INIT_LIST_HEAD(&cdev->port_dev_list);
 
-	ret = fpga_region_register(cdev->region);
-	if (ret)
+	cdev->region = fpga_region_register(info->dev, NULL, NULL);
+	if (IS_ERR(cdev->region)) {
+		ret = PTR_ERR(cdev->region);
 		goto free_cdev_exit;
+	}
 
 	/* create and init build info for enumeration */
 	binfo = devm_kzalloc(info->dev, sizeof(*binfo), GFP_KERNEL);
@@ -1864,7 +1860,7 @@
 		return -EINVAL;
 
 	fds = memdup_user((void __user *)(arg + sizeof(hdr)),
-			  hdr.count * sizeof(s32));
+			  array_size(hdr.count, sizeof(s32)));
 	if (IS_ERR(fds))
 		return PTR_ERR(fds);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/fpga-bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/fpga-bridge.c
@@ -13,6 +13,12 @@
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 
+/* For enabling manual bridge set(enable/disable) function */
+#ifdef CONFIG_DEBUG_KERNEL
+#undef DEBUG
+#define DEBUG
+#endif
+
 static DEFINE_IDA(fpga_bridge_ida);
 static struct class *fpga_bridge_class;
 
@@ -115,7 +121,7 @@
 /**
  * fpga_bridge_get - get an exclusive reference to an fpga bridge
  * @dev:	parent device that fpga bridge was registered with
- * @info:	fpga manager info
+ * @info:	fpga image specific information
  *
  * Given a device, get an exclusive reference to an fpga bridge.
  *
@@ -304,9 +310,33 @@
 static DEVICE_ATTR_RO(name);
 static DEVICE_ATTR_RO(state);
 
+#ifdef DEBUG
+static ssize_t set_store(struct device *dev,
+			 struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	struct fpga_bridge *bridge = to_fpga_bridge(dev);
+	long enable;
+	int ret;
+
+	ret = kstrtol(buf, 16, &enable);
+	if (ret)
+		return ret;
+
+	if (bridge->br_ops && bridge->br_ops->enable_set)
+		enable = bridge->br_ops->enable_set(bridge, !!enable);
+
+	return count;
+}
+static DEVICE_ATTR_WO(set);
+#endif
+
 static struct attribute *fpga_bridge_attrs[] = {
 	&dev_attr_name.attr,
 	&dev_attr_state.attr,
+#ifdef DEBUG
+	&dev_attr_set.attr,
+#endif
 	NULL,
 };
 ATTRIBUTE_GROUPS(fpga_bridge);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/fpga-mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/fpga-mgr.c
@@ -8,6 +8,9 @@
  * With code from the mailing list:
  * Copyright (C) 2013 Xilinx, Inc.
  */
+#include <linux/dma-buf.h>
+#include <linux/dma-map-ops.h>
+#include <linux/kernel.h>
 #include <linux/firmware.h>
 #include <linux/fpga/fpga-mgr.h>
 #include <linux/idr.h>
@@ -61,12 +64,14 @@
 {
 	int ret = 0;
 
+	mgr->err = 0;
 	mgr->state = FPGA_MGR_STATE_WRITE_COMPLETE;
 	if (mgr->mops->write_complete)
 		ret = mgr->mops->write_complete(mgr, info);
 	if (ret) {
 		dev_err(&mgr->dev, "Error after writing image data to FPGA\n");
 		mgr->state = FPGA_MGR_STATE_WRITE_COMPLETE_ERR;
+		mgr->err = ret;
 		return ret;
 	}
 	mgr->state = FPGA_MGR_STATE_OPERATING;
@@ -147,16 +152,18 @@
 {
 	int ret;
 
+	mgr->err = 0;
 	mgr->state = FPGA_MGR_STATE_WRITE_INIT;
 	if (!mgr->mops->initial_header_size)
 		ret = fpga_mgr_write_init(mgr, info, NULL, 0);
 	else
-		ret = fpga_mgr_write_init(
-		    mgr, info, buf, min(mgr->mops->initial_header_size, count));
+		ret = fpga_mgr_write_init(mgr, info, buf,
+					  min(mgr->mops->initial_header_size, count));
 
 	if (ret) {
 		dev_err(&mgr->dev, "Error preparing FPGA for writing\n");
 		mgr->state = FPGA_MGR_STATE_WRITE_INIT_ERR;
+		mgr->err = ret;
 		return ret;
 	}
 
@@ -226,11 +233,15 @@
 {
 	int ret;
 
+	if (info->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM)
+		memcpy(info->key, mgr->key, ENCRYPTED_KEY_LEN);
+
 	ret = fpga_mgr_write_init_sg(mgr, info, sgt);
 	if (ret)
 		return ret;
 
 	/* Write the FPGA image to the FPGA. */
+	mgr->err = 0;
 	mgr->state = FPGA_MGR_STATE_WRITE;
 	if (mgr->mops->write_sg) {
 		ret = fpga_mgr_write_sg(mgr, sgt);
@@ -249,6 +260,7 @@
 	if (ret) {
 		dev_err(&mgr->dev, "Error while writing image data to FPGA\n");
 		mgr->state = FPGA_MGR_STATE_WRITE_ERR;
+		mgr->err = ret;
 		return ret;
 	}
 
@@ -268,11 +280,13 @@
 	/*
 	 * Write the FPGA image to the FPGA.
 	 */
+	mgr->err = 0;
 	mgr->state = FPGA_MGR_STATE_WRITE;
 	ret = fpga_mgr_write(mgr, buf, count);
 	if (ret) {
 		dev_err(&mgr->dev, "Error while writing image data to FPGA\n");
 		mgr->state = FPGA_MGR_STATE_WRITE_ERR;
+		mgr->err = ret;
 		return ret;
 	}
 
@@ -351,6 +365,39 @@
 	return rc;
 }
 
+static int fpga_dmabuf_load(struct fpga_manager *mgr,
+			    struct fpga_image_info *info)
+{
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	int ret;
+
+	/* create attachment for dmabuf with the user device */
+	attach = dma_buf_attach(mgr->dmabuf, &mgr->dev);
+	if (IS_ERR(attach)) {
+		pr_err("failed to attach dmabuf\n");
+		ret = PTR_ERR(attach);
+		goto fail_put;
+	}
+
+	sgt = dma_buf_map_attachment(attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR(sgt)) {
+		ret = PTR_ERR(sgt);
+		goto fail_detach;
+	}
+
+	info->sgt = sgt;
+	ret = fpga_mgr_buf_load_sg(mgr, info, info->sgt);
+	dma_buf_unmap_attachment(attach, sgt, DMA_BIDIRECTIONAL);
+
+fail_detach:
+	dma_buf_detach(mgr->dmabuf, attach);
+fail_put:
+	dma_buf_put(mgr->dmabuf);
+
+	return ret;
+}
+
 /**
  * fpga_mgr_firmware_load - request firmware and load to fpga
  * @mgr:	fpga manager
@@ -375,11 +422,17 @@
 
 	dev_info(dev, "writing %s to %s\n", image_name, mgr->name);
 
+	mgr->err = 0;
 	mgr->state = FPGA_MGR_STATE_FIRMWARE_REQ;
 
+	/* flags indicates whether to do full or partial reconfiguration */
+	info->flags = mgr->flags;
+	memcpy(info->key, mgr->key, ENCRYPTED_KEY_LEN);
+
 	ret = request_firmware(&fw, image_name, dev);
 	if (ret) {
 		mgr->state = FPGA_MGR_STATE_FIRMWARE_REQ_ERR;
+		mgr->err = ret;
 		dev_err(dev, "Error requesting firmware %s\n", image_name);
 		return ret;
 	}
@@ -403,6 +456,8 @@
  */
 int fpga_mgr_load(struct fpga_manager *mgr, struct fpga_image_info *info)
 {
+	if (mgr->flags & FPGA_MGR_CONFIG_DMA_BUF)
+		return fpga_dmabuf_load(mgr, info);
 	if (info->sgt)
 		return fpga_mgr_buf_load_sg(mgr, info, info->sgt);
 	if (info->buf && info->count)
@@ -452,6 +507,9 @@
 {
 	struct fpga_manager *mgr = to_fpga_manager(dev);
 
+	if (mgr->err)
+		return sprintf(buf, "%s: 0x%x\n", state_str[mgr->state], mgr->err);
+
 	return sprintf(buf, "%s\n", state_str[mgr->state]);
 }
 
@@ -474,18 +532,105 @@
 		len += sprintf(buf + len, "reconfig IP protocol error\n");
 	if (status & FPGA_MGR_STATUS_FIFO_OVERFLOW_ERR)
 		len += sprintf(buf + len, "reconfig fifo overflow error\n");
+	if (status & FPGA_MGR_STATUS_SECURITY_ERR)
+		len += sprintf(buf + len, "reconfig security error\n");
+	if (status & FPGA_MGR_STATUS_DEVICE_INIT_ERR)
+		len += sprintf(buf + len,
+			       "initialization has not finished\n");
+	if (status & FPGA_MGR_STATUS_SIGNAL_ERR)
+		len += sprintf(buf + len, "device internal signal error\n");
+	if (status & FPGA_MGR_STATUS_HIGH_Z_STATE_ERR)
+		len += sprintf(buf + len,
+			       "all I/Os are placed in High-Z state\n");
+	if (status & FPGA_MGR_STATUS_EOS_ERR)
+		len += sprintf(buf + len,
+			       "start-up sequence has not finished\n");
+	if (status & FPGA_MGR_STATUS_FIRMWARE_REQ_ERR)
+		len += sprintf(buf + len, "firmware request error\n");
 
 	return len;
 }
 
+static ssize_t firmware_store(struct device *dev,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct fpga_manager *mgr = to_fpga_manager(dev);
+	unsigned int len;
+	char image_name[NAME_MAX];
+	int ret;
+
+	/* struct with information about the FPGA image to program. */
+	struct fpga_image_info info = {0};
+
+	/* lose terminating \n */
+	strcpy(image_name, buf);
+	len = strlen(image_name);
+	if (image_name[len - 1] == '\n')
+		image_name[len - 1] = 0;
+
+	ret = fpga_mgr_firmware_load(mgr, &info, image_name);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
+static ssize_t key_show(struct device *dev,
+			struct device_attribute *attr, char *buf)
+{
+	struct fpga_manager *mgr = to_fpga_manager(dev);
+
+	return snprintf(buf, ENCRYPTED_KEY_LEN + 1, "%s\n", mgr->key);
+}
+
+static ssize_t key_store(struct device *dev,
+			 struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	struct fpga_manager *mgr = to_fpga_manager(dev);
+
+	memcpy(mgr->key, buf, count);
+
+	return count;
+}
+
+static ssize_t flags_show(struct device *dev,
+			  struct device_attribute *attr, char *buf)
+{
+	struct fpga_manager *mgr = to_fpga_manager(dev);
+
+	return sprintf(buf, "%lx\n", mgr->flags);
+}
+
+static ssize_t flags_store(struct device *dev,
+			   struct device_attribute *attr,
+			   const char *buf, size_t count)
+{
+	struct fpga_manager *mgr = to_fpga_manager(dev);
+	int ret;
+
+	ret = kstrtol(buf, 16, &mgr->flags);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
 static DEVICE_ATTR_RO(name);
 static DEVICE_ATTR_RO(state);
 static DEVICE_ATTR_RO(status);
+static DEVICE_ATTR_WO(firmware);
+static DEVICE_ATTR_RW(flags);
+static DEVICE_ATTR_RW(key);
 
 static struct attribute *fpga_mgr_attrs[] = {
 	&dev_attr_name.attr,
 	&dev_attr_state.attr,
 	&dev_attr_status.attr,
+	&dev_attr_firmware.attr,
+	&dev_attr_flags.attr,
+	&dev_attr_key.attr,
 	NULL,
 };
 ATTRIBUTE_GROUPS(fpga_mgr);
@@ -558,6 +703,106 @@
 }
 EXPORT_SYMBOL_GPL(fpga_mgr_put);
 
+#ifdef CONFIG_FPGA_MGR_DEBUG_FS
+#include <linux/debugfs.h>
+
+static int fpga_mgr_read(struct seq_file *s, void *data)
+{
+	struct fpga_manager *mgr = (struct fpga_manager *)s->private;
+	int ret = 0;
+
+	if (!mgr->mops->read)
+		return -ENOENT;
+
+	if (!mutex_trylock(&mgr->ref_mutex))
+		return -EBUSY;
+
+	if (mgr->state != FPGA_MGR_STATE_OPERATING) {
+		ret = -EPERM;
+		goto err_unlock;
+	}
+
+	/* Read the FPGA configuration data from the fabric */
+	ret = mgr->mops->read(mgr, s);
+	if (ret)
+		dev_err(&mgr->dev, "Error while reading configuration data from FPGA\n");
+
+err_unlock:
+	mutex_unlock(&mgr->ref_mutex);
+
+	return ret;
+}
+
+static int fpga_mgr_read_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, fpga_mgr_read, inode->i_private);
+}
+
+static const struct file_operations fpga_mgr_ops_image = {
+	.owner = THIS_MODULE,
+	.open = fpga_mgr_read_open,
+	.read = seq_read,
+};
+#endif
+
+static int fpga_dmabuf_fd_get(struct file *file, char __user *argp)
+{
+	struct fpga_manager *mgr =  (struct fpga_manager *)(file->private_data);
+	int buffd;
+
+	if (copy_from_user(&buffd, argp, sizeof(buffd)))
+		return -EFAULT;
+
+	mgr->dmabuf = dma_buf_get(buffd);
+	if (IS_ERR_OR_NULL(mgr->dmabuf))
+		return -EINVAL;
+
+	mgr->flags = FPGA_MGR_CONFIG_DMA_BUF;
+
+	return 0;
+}
+
+static int fpga_device_open(struct inode *inode, struct file *file)
+{
+	struct miscdevice *miscdev = file->private_data;
+	struct fpga_manager *mgr = container_of(miscdev,
+						struct fpga_manager, miscdev);
+
+	file->private_data = mgr;
+
+	return 0;
+}
+
+static int fpga_device_release(struct inode *inode, struct file *file)
+{
+	return 0;
+}
+
+static long fpga_device_ioctl(struct file *file, unsigned int cmd,
+			      unsigned long arg)
+{
+	char __user *argp = (char __user *)arg;
+	int err;
+
+	switch (cmd) {
+	case FPGA_IOCTL_LOAD_DMA_BUFF:
+		err = fpga_dmabuf_fd_get(file, argp);
+		break;
+	default:
+		err = -ENOTTY;
+	}
+
+	return err;
+}
+
+static const struct file_operations fpga_fops = {
+	.owner		= THIS_MODULE,
+	.open		= fpga_device_open,
+	.release	= fpga_device_release,
+	.unlocked_ioctl	= fpga_device_ioctl,
+	.compat_ioctl	= fpga_device_ioctl,
+};
+
 /**
  * fpga_mgr_lock - Lock FPGA manager for exclusive use
  * @mgr:	fpga manager
@@ -641,10 +886,28 @@
 	mgr->dev.of_node = parent->of_node;
 	mgr->dev.id = id;
 
+	/* Make device dma capable by inheriting from parent's */
+	set_dma_ops(&mgr->dev, get_dma_ops(parent));
+	ret = dma_coerce_mask_and_coherent(&mgr->dev, dma_get_mask(parent));
+	if (ret) {
+		dev_warn(parent,
+			 "Failed to set DMA mask %llx. Trying to continue... %x\n",
+			 dma_get_mask(parent), ret);
+	}
+
 	ret = dev_set_name(&mgr->dev, "fpga%d", id);
 	if (ret)
 		goto error_device;
 
+	mgr->miscdev.minor = MISC_DYNAMIC_MINOR;
+	mgr->miscdev.name = kobject_name(&mgr->dev.kobj);
+	mgr->miscdev.fops = &fpga_fops;
+	ret = misc_register(&mgr->miscdev);
+	if (ret) {
+		pr_err("fpga: failed to register misc device.\n");
+		goto error_device;
+	}
+
 	return mgr;
 
 error_device:
@@ -722,6 +985,9 @@
 int fpga_mgr_register(struct fpga_manager *mgr)
 {
 	int ret;
+#ifdef CONFIG_FPGA_MGR_DEBUG_FS
+	struct dentry *d, *parent;
+#endif
 
 	/*
 	 * Initialize framework state by requesting low level driver read state
@@ -734,6 +1000,26 @@
 	if (ret)
 		goto error_device;
 
+#ifdef CONFIG_FPGA_MGR_DEBUG_FS
+	mgr->dir = debugfs_create_dir("fpga", NULL);
+	if (!mgr->dir)
+		goto error_device;
+
+	parent = mgr->dir;
+	d = debugfs_create_dir(mgr->dev.kobj.name, parent);
+	if (!d) {
+		debugfs_remove_recursive(parent);
+		goto error_device;
+	}
+
+	parent = d;
+	d = debugfs_create_file("image", 0644, parent, mgr,
+				&fpga_mgr_ops_image);
+	if (!d) {
+		debugfs_remove_recursive(mgr->dir);
+		goto error_device;
+	}
+#endif
 	dev_info(&mgr->dev, "%s registered\n", mgr->name);
 
 	return 0;
@@ -755,6 +1041,10 @@
 {
 	dev_info(&mgr->dev, "%s %s\n", __func__, mgr->name);
 
+#ifdef CONFIG_FPGA_MGR_DEBUG_FS
+	debugfs_remove_recursive(mgr->dir);
+#endif
+
 	/*
 	 * If the low level driver provides a method for putting fpga into
 	 * a desired state upon unregister, do it.
@@ -785,6 +1075,8 @@
  * @dev: managing device for this FPGA manager
  * @mgr: fpga manager struct
  *
+ * @return: 0 on success, negative error code otherwise.
+ *
  * This is the devres variant of fpga_mgr_register() for which the unregister
  * function will be called automatically when the managing device is detached.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/fpga-region.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/fpga-region.c
@@ -52,7 +52,7 @@
 	}
 
 	get_device(dev);
-	if (!try_module_get(dev->parent->driver->owner)) {
+	if (!try_module_get(region->ops_owner)) {
 		put_device(dev);
 		mutex_unlock(&region->mutex);
 		return ERR_PTR(-ENODEV);
@@ -74,7 +74,7 @@
 
 	dev_dbg(dev, "put\n");
 
-	module_put(dev->parent->driver->owner);
+	module_put(region->ops_owner);
 	put_device(dev);
 	mutex_unlock(&region->mutex);
 }
@@ -180,39 +180,45 @@
 ATTRIBUTE_GROUPS(fpga_region);
 
 /**
- * fpga_region_create - alloc and init a struct fpga_region
+ * __fpga_region_register_full - create and register an FPGA Region device
  * @parent: device parent
- * @mgr: manager that programs this region
- * @get_bridges: optional function to get bridges to a list
- *
- * The caller of this function is responsible for freeing the resulting region
- * struct with fpga_region_free().  Using devm_fpga_region_create() instead is
- * recommended.
+ * @info: parameters for FPGA Region
+ * @owner: module containing the get_bridges function
  *
- * Return: struct fpga_region or NULL
+ * Return: struct fpga_region or ERR_PTR()
  */
-struct fpga_region
-*fpga_region_create(struct device *parent,
-		    struct fpga_manager *mgr,
-		    int (*get_bridges)(struct fpga_region *))
+struct fpga_region *
+__fpga_region_register_full(struct device *parent, const struct fpga_region_info *info,
+			    struct module *owner)
 {
 	struct fpga_region *region;
 	int id, ret = 0;
 
+	if (!info) {
+		dev_err(parent,
+			"Attempt to register without required info structure\n");
+		return ERR_PTR(-EINVAL);
+	}
+
 	region = kzalloc(sizeof(*region), GFP_KERNEL);
 	if (!region)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	id = ida_simple_get(&fpga_region_ida, 0, 0, GFP_KERNEL);
-	if (id < 0)
+	if (id < 0) {
+		ret = id;
 		goto err_free;
+	}
+
+	region->mgr = info->mgr;
+	region->compat_id = info->compat_id;
+	region->priv = info->priv;
+	region->get_bridges = info->get_bridges;
+	region->ops_owner = owner;
 
-	region->mgr = mgr;
-	region->get_bridges = get_bridges;
 	mutex_init(&region->mutex);
 	INIT_LIST_HEAD(&region->bridge_list);
 
-	device_initialize(&region->dev);
 	region->dev.class = fpga_region_class;
 	region->dev.parent = parent;
 	region->dev.of_node = parent->of_node;
@@ -222,6 +228,12 @@
 	if (ret)
 		goto err_remove;
 
+	ret = device_register(&region->dev);
+	if (ret) {
+		put_device(&region->dev);
+		return ERR_PTR(ret);
+	}
+
 	return region;
 
 err_remove:
@@ -229,78 +241,35 @@
 err_free:
 	kfree(region);
 
-	return NULL;
+	return ERR_PTR(ret);
 }
-EXPORT_SYMBOL_GPL(fpga_region_create);
+EXPORT_SYMBOL_GPL(__fpga_region_register_full);
 
 /**
- * fpga_region_free - free an FPGA region created by fpga_region_create()
- * @region: FPGA region
- */
-void fpga_region_free(struct fpga_region *region)
-{
-	ida_simple_remove(&fpga_region_ida, region->dev.id);
-	kfree(region);
-}
-EXPORT_SYMBOL_GPL(fpga_region_free);
-
-static void devm_fpga_region_release(struct device *dev, void *res)
-{
-	struct fpga_region *region = *(struct fpga_region **)res;
-
-	fpga_region_free(region);
-}
-
-/**
- * devm_fpga_region_create - create and initialize a managed FPGA region struct
+ * __fpga_region_register - create and register an FPGA Region device
  * @parent: device parent
  * @mgr: manager that programs this region
  * @get_bridges: optional function to get bridges to a list
+ * @owner: module containing the get_bridges function
  *
- * This function is intended for use in an FPGA region driver's probe function.
- * After the region driver creates the region struct with
- * devm_fpga_region_create(), it should register it with fpga_region_register().
- * The region driver's remove function should call fpga_region_unregister().
- * The region struct allocated with this function will be freed automatically on
- * driver detach.  This includes the case of a probe function returning error
- * before calling fpga_region_register(), the struct will still get cleaned up.
+ * This simple version of the register function should be sufficient for most users.
+ * The fpga_region_register_full() function is available for users that need to
+ * pass additional, optional parameters.
  *
- * Return: struct fpga_region or NULL
+ * Return: struct fpga_region or ERR_PTR()
  */
-struct fpga_region
-*devm_fpga_region_create(struct device *parent,
-			 struct fpga_manager *mgr,
-			 int (*get_bridges)(struct fpga_region *))
+struct fpga_region *
+__fpga_region_register(struct device *parent, struct fpga_manager *mgr,
+		       int (*get_bridges)(struct fpga_region *), struct module *owner)
 {
-	struct fpga_region **ptr, *region;
+	struct fpga_region_info info = { 0 };
 
-	ptr = devres_alloc(devm_fpga_region_release, sizeof(*ptr), GFP_KERNEL);
-	if (!ptr)
-		return NULL;
-
-	region = fpga_region_create(parent, mgr, get_bridges);
-	if (!region) {
-		devres_free(ptr);
-	} else {
-		*ptr = region;
-		devres_add(parent, ptr);
-	}
+	info.mgr = mgr;
+	info.get_bridges = get_bridges;
 
-	return region;
+	return __fpga_region_register_full(parent, &info, owner);
 }
-EXPORT_SYMBOL_GPL(devm_fpga_region_create);
-
-/**
- * fpga_region_register - register an FPGA region
- * @region: FPGA region
- *
- * Return: 0 or -errno
- */
-int fpga_region_register(struct fpga_region *region)
-{
-	return device_add(&region->dev);
-}
-EXPORT_SYMBOL_GPL(fpga_region_register);
+EXPORT_SYMBOL_GPL(__fpga_region_register);
 
 /**
  * fpga_region_unregister - unregister an FPGA region
@@ -316,6 +285,10 @@
 
 static void fpga_region_dev_release(struct device *dev)
 {
+	struct fpga_region *region = to_fpga_region(dev);
+
+	ida_simple_remove(&fpga_region_ida, region->dev.id);
+	kfree(region);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/of-fpga-region.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/of-fpga-region.c
@@ -15,6 +15,7 @@
 #include <linux/of_platform.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/pm_runtime.h>
 
 static const struct of_device_id fpga_region_of_match[] = {
 	{ .compatible = "fpga-region", },
@@ -28,7 +29,7 @@
  *
  * Caller will need to put_device(&region->dev) when done.
  *
- * Returns FPGA Region struct or NULL
+ * @return: FPGA Region struct or NULL
  */
 static struct fpga_region *of_fpga_region_find(struct device_node *np)
 {
@@ -80,7 +81,7 @@
  * Caller should call fpga_bridges_put(&region->bridge_list) when
  * done with the bridges.
  *
- * Return 0 for success (even if there are no bridges specified)
+ * @return: 0 for success (even if there are no bridges specified)
  * or -EBUSY if any of the bridges are in use.
  */
 static int of_fpga_region_get_bridges(struct fpga_region *region)
@@ -139,13 +140,13 @@
 }
 
 /**
- * child_regions_with_firmware
+ * child_regions_with_firmware - Used to check the child region info.
  * @overlay: device node of the overlay
  *
  * If the overlay adds child FPGA regions, they are not allowed to have
  * firmware-name property.
  *
- * Return 0 for OK or -EINVAL if child FPGA region adds firmware-name.
+ * @return: 0 for OK or -EINVAL if child FPGA region adds firmware-name.
  */
 static int child_regions_with_firmware(struct device_node *overlay)
 {
@@ -228,6 +229,16 @@
 	if (of_property_read_bool(overlay, "encrypted-fpga-config"))
 		info->flags |= FPGA_MGR_ENCRYPTED_BITSTREAM;
 
+	if (of_property_read_bool(overlay, "userkey-encrypted-fpga-config"))
+		info->flags |= FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM;
+
+	if (of_property_read_bool(overlay, "ddrmem-authenticated-fpga-config"))
+		info->flags |= FPGA_MGR_DDR_MEM_AUTH_BITSTREAM;
+
+	if (of_property_read_bool(overlay,
+				  "securemem-authenticated-fpga-config"))
+		info->flags |= FPGA_MGR_SECURE_MEM_AUTH_BITSTREAM;
+
 	if (!of_property_read_string(overlay, "firmware-name",
 				     &firmware_name)) {
 		info->firmware_name = devm_kstrdup(dev, firmware_name,
@@ -279,7 +290,7 @@
  * If the checks fail, overlay is rejected and does not get added to the
  * live tree.
  *
- * Returns 0 for success or negative error code for failure.
+ * @return: 0 for success or negative error code for failure.
  */
 static int of_fpga_region_notify_pre_apply(struct fpga_region *region,
 					   struct of_overlay_notify_data *nd)
@@ -302,6 +313,9 @@
 	}
 
 	region->info = info;
+	pm_runtime_put_sync(dev->parent);
+	pm_runtime_barrier(dev->parent);
+	pm_runtime_get_sync(dev->parent);
 	ret = fpga_region_program_fpga(region);
 	if (ret) {
 		/* error; reject overlay */
@@ -324,10 +338,13 @@
 static void of_fpga_region_notify_post_remove(struct fpga_region *region,
 					      struct of_overlay_notify_data *nd)
 {
+	struct device *dev = &region->dev;
+
 	fpga_bridges_disable(&region->bridge_list);
 	fpga_bridges_put(&region->bridge_list);
 	fpga_image_info_free(region->info);
 	region->info = NULL;
+	pm_runtime_put(dev->parent);
 }
 
 /**
@@ -339,7 +356,7 @@
  * This notifier handles programming an FPGA when a "firmware-name" property is
  * added to an fpga-region.
  *
- * Returns NOTIFY_OK or error if FPGA programming fails.
+ * @return: NOTIFY_OK or error if FPGA programming fails.
  */
 static int of_fpga_region_notify(struct notifier_block *nb,
 				 unsigned long action, void *arg)
@@ -405,15 +422,16 @@
 	if (IS_ERR(mgr))
 		return -EPROBE_DEFER;
 
-	region = devm_fpga_region_create(dev, mgr, of_fpga_region_get_bridges);
-	if (!region) {
-		ret = -ENOMEM;
-		goto eprobe_mgr_put;
+	region = fpga_region_register(dev, mgr, of_fpga_region_get_bridges);
+	if (IS_ERR(region)) {
+		ret = PTR_ERR(region);
+		goto err_pm;
 	}
 
-	ret = fpga_region_register(region);
-	if (ret)
-		goto eprobe_mgr_put;
+	pm_runtime_enable(&pdev->dev);
+	ret = pm_runtime_get_sync(&pdev->dev);
+	if (ret < 0)
+		goto err_pm;
 
 	of_platform_populate(np, fpga_region_of_match, NULL, &region->dev);
 	platform_set_drvdata(pdev, region);
@@ -422,6 +440,9 @@
 
 	return 0;
 
+err_pm:
+	pm_runtime_put(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
 eprobe_mgr_put:
 	fpga_mgr_put(mgr);
 	return ret;
@@ -434,6 +455,7 @@
 
 	fpga_region_unregister(region);
 	fpga_mgr_put(mgr);
+	pm_runtime_disable(region->dev.parent);
 
 	return 0;
 }
@@ -448,8 +470,10 @@
 };
 
 /**
- * fpga_region_init - init function for fpga_region class
+ * of_fpga_region_init - init function for fpga_region class
  * Creates the fpga_region class and registers a reconfig notifier.
+ *
+ * @return: 0 on success, negative error code otherwise.
  */
 static int __init of_fpga_region_init(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/stratix10-soc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/stratix10-soc.c
@@ -213,9 +213,9 @@
 	/* Allocate buffers from the service layer's pool. */
 	for (i = 0; i < NUM_SVC_BUFS; i++) {
 		kbuf = stratix10_svc_allocate_memory(priv->chan, SVC_BUF_SIZE);
-		if (!kbuf) {
+		if (IS_ERR(kbuf)) {
 			s10_free_buffers(mgr);
-			ret = -ENOMEM;
+			ret = PTR_ERR(kbuf);
 			goto init_done;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/versal-fpga.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/versal-fpga.c
@@ -19,6 +19,18 @@
 	return 0;
 }
 
+static int versal_fpga_ops_write_sg(struct fpga_manager *mgr,
+				    struct sg_table *sgt)
+{
+	dma_addr_t dma_addr;
+	int ret;
+
+	dma_addr = sg_dma_address(sgt->sgl);
+	ret = zynqmp_pm_load_pdi(PDI_SRC_DDR, dma_addr);
+
+	return ret;
+}
+
 static int versal_fpga_ops_write(struct fpga_manager *mgr,
 				 const char *buf, size_t size)
 {
@@ -40,6 +52,7 @@
 static const struct fpga_manager_ops versal_fpga_ops = {
 	.write_init = versal_fpga_ops_write_init,
 	.write = versal_fpga_ops_write,
+	.write_sg = versal_fpga_ops_write_sg,
 };
 
 static int versal_fpga_probe(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/xilinx-afi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/xilinx-afi.c
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA AFI bridge.
+ * Copyright (c) 2018 Xilinx Inc.
+ */
+
+#include <linux/err.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+/**
+ * struct afi_fpga - AFI register description
+ * @value: value to be written to the register
+ * @regid: Register id for the register to be written
+ * @resets: Pointer to the reset control for ps-pl resets.
+ */
+struct afi_fpga {
+	u32 value;
+	u32 regid;
+	struct reset_control *resets;
+};
+
+static int afi_fpga_probe(struct platform_device *pdev)
+{
+	struct afi_fpga *afi_fpga;
+	struct device_node *np = pdev->dev.of_node;
+	int ret;
+	int i, entries, pairs;
+	u32 reg, val;
+
+	afi_fpga = devm_kzalloc(&pdev->dev, sizeof(*afi_fpga), GFP_KERNEL);
+	if (!afi_fpga)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, afi_fpga);
+
+	/* Reset PL */
+	afi_fpga->resets = devm_reset_control_array_get_optional_exclusive(&pdev->dev);
+	if (IS_ERR(afi_fpga->resets))
+		return PTR_ERR(afi_fpga->resets);
+
+	reset_control_deassert(afi_fpga->resets);
+
+	entries = of_property_count_u32_elems(np, "config-afi");
+	if (!entries || (entries % 2)) {
+		dev_err(&pdev->dev, "Invalid number of registers\n");
+		return -EINVAL;
+	}
+	pairs = entries / 2;
+
+	for (i = 0; i < pairs; i++) {
+		ret = of_property_read_u32_index(np, "config-afi", i * 2,
+						 &reg);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to read register\n");
+			return -EINVAL;
+		}
+		ret = of_property_read_u32_index(np, "config-afi", i * 2 + 1,
+						 &val);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to read value\n");
+			return -EINVAL;
+		}
+		ret = zynqmp_pm_afi(reg, val);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "AFI register write error %d\n",
+				ret);
+			return ret;
+		}
+	}
+
+	reset_control_assert(afi_fpga->resets);
+
+	return 0;
+}
+
+static const struct of_device_id afi_fpga_ids[] = {
+	{ .compatible = "xlnx,afi-fpga" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, afi_fpga_ids);
+
+static struct platform_driver afi_fpga_driver = {
+	.driver = {
+		.name = "afi-fpga",
+		.of_match_table = afi_fpga_ids,
+	},
+	.probe = afi_fpga_probe,
+};
+module_platform_driver(afi_fpga_driver);
+
+MODULE_DESCRIPTION("FPGA afi module");
+MODULE_AUTHOR("Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/zynq-afi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/zynq-afi.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA AFI driver.
+ * Copyright (c) 2018 Xilinx Inc.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+/* Registers and special values for doing register-based operations */
+#define AFI_RDCHAN_CTRL_OFFSET	0x00
+#define AFI_WRCHAN_CTRL_OFFSET	0x14
+
+#define AFI_BUSWIDTH_MASK	0x01
+
+/**
+ * struct afi_fpga - AFI register description
+ * @membase:	pointer to register struct
+ * @afi_width:	AFI bus width to be written
+ */
+struct zynq_afi_fpga {
+	void __iomem	*membase;
+	u32		afi_width;
+};
+
+static int zynq_afi_fpga_probe(struct platform_device *pdev)
+{
+	struct zynq_afi_fpga *afi_fpga;
+	struct resource *res;
+	u32 reg_val;
+	u32 val;
+
+	afi_fpga = devm_kzalloc(&pdev->dev, sizeof(*afi_fpga), GFP_KERNEL);
+	if (!afi_fpga)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	afi_fpga->membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(afi_fpga->membase))
+		return PTR_ERR(afi_fpga->membase);
+
+	val = device_property_read_u32(&pdev->dev, "xlnx,afi-width",
+				       &afi_fpga->afi_width);
+	if (val) {
+		dev_err(&pdev->dev, "Fail to get the afi bus width\n");
+		return -EINVAL;
+	}
+
+	reg_val = readl(afi_fpga->membase + AFI_RDCHAN_CTRL_OFFSET);
+	reg_val &= ~AFI_BUSWIDTH_MASK;
+	writel(reg_val | afi_fpga->afi_width,
+	       afi_fpga->membase + AFI_RDCHAN_CTRL_OFFSET);
+	reg_val = readl(afi_fpga->membase + AFI_WRCHAN_CTRL_OFFSET);
+	reg_val &= ~AFI_BUSWIDTH_MASK;
+	writel(reg_val | afi_fpga->afi_width,
+	       afi_fpga->membase + AFI_WRCHAN_CTRL_OFFSET);
+
+	return 0;
+}
+
+static const struct of_device_id zynq_afi_fpga_ids[] = {
+	{ .compatible = "xlnx,zynq-afi-fpga" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, zynq_afi_fpga_ids);
+
+static struct platform_driver zynq_afi_fpga_driver = {
+	.driver = {
+		.name = "zynq-afi-fpga",
+		.of_match_table = zynq_afi_fpga_ids,
+	},
+	.probe = zynq_afi_fpga_probe,
+};
+module_platform_driver(zynq_afi_fpga_driver);
+
+MODULE_DESCRIPTION("ZYNQ FPGA AFI module");
+MODULE_AUTHOR("Nava kishore Manne <nava.manne@xilinx.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/zynq-fpga.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/zynq-fpga.c
@@ -275,7 +275,7 @@
 
 	/* don't globally reset PL if we're doing partial reconfig */
 	if (!(info->flags & FPGA_MGR_PARTIAL_RECONFIG)) {
-		if (!zynq_fpga_has_sync(buf, count)) {
+		if (!zynq_fpga_has_sync((u8 *)buf, count)) {
 			dev_err(&mgr->dev,
 				"Invalid bitstream, could not find a sync word. Bitstream must be a byte swapped .bin file\n");
 			err = -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fpga/zynqmp-fpga.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fpga/zynqmp-fpga.c
@@ -9,20 +9,96 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of_address.h>
+#include <linux/seq_file.h>
 #include <linux/string.h>
 #include <linux/firmware/xlnx-zynqmp.h>
 
 /* Constant Definitions */
 #define IXR_FPGA_DONE_MASK	BIT(3)
 
+#define READ_DMA_SIZE		0x200
+#define DUMMY_FRAMES_SIZE	0x64
+
+/* Error Register */
+#define IXR_FPGA_ERR_CRC_ERR		BIT(0)
+#define IXR_FPGA_ERR_SECURITY_ERR	BIT(16)
+
+/* Signal Status Register */
+#define IXR_FPGA_END_OF_STARTUP		BIT(4)
+#define IXR_FPGA_GST_CFG_B		BIT(5)
+#define IXR_FPGA_INIT_B_INTERNAL	BIT(11)
+#define IXR_FPGA_DONE_INTERNAL_SIGNAL	BIT(13)
+
+#define IXR_FPGA_CONFIG_STAT_OFFSET	7U
+#define IXR_FPGA_READ_CONFIG_TYPE	0U
+
+#define XILINX_ZYNQMP_PM_FPGA_READ_BACK		BIT(6)
+#define XILINX_ZYNQMP_PM_FPGA_REG_READ_BACK	BIT(7)
+
+#define DEFAULT_FEATURE_LIST	(XILINX_ZYNQMP_PM_FPGA_FULL | \
+				 XILINX_ZYNQMP_PM_FPGA_PARTIAL | \
+				 XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_DDR | \
+				 XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_OCM | \
+				 XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_USERKEY | \
+				 XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_DEVKEY | \
+				 XILINX_ZYNQMP_PM_FPGA_READ_BACK | \
+				 XILINX_ZYNQMP_PM_FPGA_REG_READ_BACK)
+
+static bool readback_type;
+module_param(readback_type, bool, 0644);
+MODULE_PARM_DESC(readback_type,
+		 "readback_type 0-configuration register read "
+		 "1- configuration data read (default: 0)");
+
+/**
+ * struct zynqmp_configreg - Configuration register offsets
+ * @reg:	Name of the configuration register.
+ * @offset:	Register offset.
+ */
+struct zynqmp_configreg {
+	char *reg;
+	u32 offset;
+};
+
+static struct zynqmp_configreg cfgreg[] = {
+	{.reg = "CRC",		.offset = 0},
+	{.reg = "FAR",		.offset = 1},
+	{.reg = "FDRI",		.offset = 2},
+	{.reg = "FDRO",		.offset = 3},
+	{.reg = "CMD",		.offset = 4},
+	{.reg = "CTRL0",	.offset = 5},
+	{.reg = "MASK",		.offset = 6},
+	{.reg = "STAT",		.offset = 7},
+	{.reg = "LOUT",		.offset = 8},
+	{.reg = "COR0",		.offset = 9},
+	{.reg = "MFWR",		.offset = 10},
+	{.reg = "CBC",		.offset = 11},
+	{.reg = "IDCODE",	.offset = 12},
+	{.reg = "AXSS",		.offset = 13},
+	{.reg = "COR1",		.offset = 14},
+	{.reg = "WBSTR",	.offset = 16},
+	{.reg = "TIMER",	.offset = 17},
+	{.reg = "BOOTSTS",	.offset = 22},
+	{.reg = "CTRL1",	.offset = 24},
+	{}
+};
+
 /**
  * struct zynqmp_fpga_priv - Private data structure
  * @dev:	Device data structure
+ * @feature_list: Firmware supported feature list
+ * @version: Firmware version info. The higher 16 bytes belong to
+ *           the major version number and the lower 16 bytes belong
+ *           to a minor version number.
  * @flags:	flags which is used to identify the bitfile type
+ * @size:	Size of the Bit-stream used for readback
  */
 struct zynqmp_fpga_priv {
 	struct device *dev;
+	u32 feature_list;
+	u32 version;
 	u32 flags;
+	u32 size;
 };
 
 static int zynqmp_fpga_ops_write_init(struct fpga_manager *mgr,
@@ -30,10 +106,27 @@
 				      const char *buf, size_t size)
 {
 	struct zynqmp_fpga_priv *priv;
+	int  eemi_flags = 0;
 
 	priv = mgr->priv;
 	priv->flags = info->flags;
 
+	/* Update firmware flags */
+	if (priv->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_USERKEY;
+	else if (priv->flags & FPGA_MGR_ENCRYPTED_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_DEVKEY;
+	if (priv->flags & FPGA_MGR_DDR_MEM_AUTH_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_DDR;
+	else if (priv->flags & FPGA_MGR_SECURE_MEM_AUTH_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_OCM;
+	if (priv->flags & FPGA_MGR_PARTIAL_RECONFIG)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_PARTIAL;
+
+	/* Validate user flgas with firmware feature list */
+	if ((priv->feature_list & eemi_flags) != eemi_flags)
+		return -EINVAL;
+
 	return 0;
 }
 
@@ -41,27 +134,119 @@
 				 const char *buf, size_t size)
 {
 	struct zynqmp_fpga_priv *priv;
-	dma_addr_t dma_addr;
+	dma_addr_t dma_addr = 0;
 	u32 eemi_flags = 0;
+	size_t dma_size;
+	u32 status;
 	char *kbuf;
 	int ret;
 
 	priv = mgr->priv;
+	priv->size = size;
+
+	if (priv->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM)
+		dma_size = size + ENCRYPTED_KEY_LEN;
+	else
+		dma_size = size;
 
-	kbuf = dma_alloc_coherent(priv->dev, size, &dma_addr, GFP_KERNEL);
+	kbuf = dma_alloc_coherent(priv->dev, dma_size, &dma_addr, GFP_KERNEL);
 	if (!kbuf)
 		return -ENOMEM;
 
 	memcpy(kbuf, buf, size);
 
+	if (priv->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM) {
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_USERKEY;
+		memcpy(kbuf + size, mgr->key, ENCRYPTED_KEY_LEN);
+	} else if (priv->flags & FPGA_MGR_ENCRYPTED_BITSTREAM) {
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_DEVKEY;
+	}
+
 	wmb(); /* ensure all writes are done before initiate FW call */
 
+	if (priv->flags & FPGA_MGR_DDR_MEM_AUTH_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_DDR;
+	else if (priv->flags & FPGA_MGR_SECURE_MEM_AUTH_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_OCM;
+
 	if (priv->flags & FPGA_MGR_PARTIAL_RECONFIG)
 		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_PARTIAL;
 
-	ret = zynqmp_pm_fpga_load(dma_addr, size, eemi_flags);
+	if (priv->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM)
+		ret = zynqmp_pm_fpga_load(dma_addr, dma_addr + size,
+					  eemi_flags, &status);
+	else
+		ret = zynqmp_pm_fpga_load(dma_addr, size,
+					  eemi_flags, &status);
+
+	dma_free_coherent(priv->dev, dma_size, kbuf, dma_addr);
+
+	if (status)
+		return status;
+
+	return ret;
+}
+
+static unsigned long zynqmp_fpga_get_contiguous_size(struct sg_table *sgt)
+{
+	dma_addr_t expected = sg_dma_address(sgt->sgl);
+	unsigned long size = 0;
+	struct scatterlist *s;
+	unsigned int i;
+
+	for_each_sg(sgt->sgl, s, sgt->nents, i) {
+		if (sg_dma_address(s) != expected)
+			break;
+		expected = sg_dma_address(s) + sg_dma_len(s);
+		size += sg_dma_len(s);
+	}
+
+	return size;
+}
+
+static int zynqmp_fpga_ops_write_sg(struct fpga_manager *mgr,
+				    struct sg_table *sgt)
+{
+	dma_addr_t dma_addr, key_addr = 0;
+	struct zynqmp_fpga_priv *priv;
+	unsigned long contig_size;
+	u32 eemi_flags = 0;
+	u32 status;
+	char *kbuf;
+	int ret;
+
+	priv = mgr->priv;
+
+	dma_addr = sg_dma_address(sgt->sgl);
+	contig_size = zynqmp_fpga_get_contiguous_size(sgt);
+
+	if (priv->flags & FPGA_MGR_PARTIAL_RECONFIG)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_PARTIAL;
+	if (priv->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_USERKEY;
+	else if (priv->flags & FPGA_MGR_ENCRYPTED_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_DEVKEY;
+	if (priv->flags & FPGA_MGR_DDR_MEM_AUTH_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_DDR;
+	else if (priv->flags & FPGA_MGR_SECURE_MEM_AUTH_BITSTREAM)
+		eemi_flags |= XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_OCM;
+
+	if (priv->flags & FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM) {
+		kbuf = dma_alloc_coherent(priv->dev, ENCRYPTED_KEY_LEN,
+					  &key_addr, GFP_KERNEL);
+		if (!kbuf)
+			return -ENOMEM;
+		memcpy(kbuf, mgr->key, ENCRYPTED_KEY_LEN);
+		ret = zynqmp_pm_fpga_load(dma_addr, key_addr,
+					  eemi_flags, &status);
+		dma_free_coherent(priv->dev, ENCRYPTED_KEY_LEN, kbuf, key_addr);
+	} else {
+		ret = zynqmp_pm_fpga_load(dma_addr, contig_size,
+					  eemi_flags, &status);
+	}
 
-	dma_free_coherent(priv->dev, size, kbuf, dma_addr);
+	if (status)
+		return status;
 
 	return ret;
 }
@@ -77,10 +262,137 @@
 	return FPGA_MGR_STATE_UNKNOWN;
 }
 
+static u64 zynqmp_fpga_ops_status(struct fpga_manager *mgr)
+{
+	unsigned int *buf, reg_val;
+	dma_addr_t dma_addr = 0;
+	u64 status = 0;
+	int ret;
+
+	buf = dma_alloc_coherent(mgr->dev.parent, READ_DMA_SIZE,
+				 &dma_addr, GFP_KERNEL);
+	if (!buf)
+		return FPGA_MGR_STATUS_FIRMWARE_REQ_ERR;
+
+	ret = zynqmp_pm_fpga_read(IXR_FPGA_CONFIG_STAT_OFFSET, dma_addr,
+				  IXR_FPGA_READ_CONFIG_TYPE, &reg_val);
+	if (ret) {
+		status = FPGA_MGR_STATUS_FIRMWARE_REQ_ERR;
+		goto free_dmabuf;
+	}
+
+	if (reg_val & IXR_FPGA_ERR_CRC_ERR)
+		status |= FPGA_MGR_STATUS_CRC_ERR;
+	if (reg_val & IXR_FPGA_ERR_SECURITY_ERR)
+		status |= FPGA_MGR_STATUS_SECURITY_ERR;
+	if (!(reg_val & IXR_FPGA_INIT_B_INTERNAL))
+		status |= FPGA_MGR_STATUS_DEVICE_INIT_ERR;
+	if (!(reg_val & IXR_FPGA_DONE_INTERNAL_SIGNAL))
+		status |= FPGA_MGR_STATUS_SIGNAL_ERR;
+	if (!(reg_val & IXR_FPGA_GST_CFG_B))
+		status |= FPGA_MGR_STATUS_HIGH_Z_STATE_ERR;
+	if (!(reg_val & IXR_FPGA_END_OF_STARTUP))
+		status |= FPGA_MGR_STATUS_EOS_ERR;
+
+free_dmabuf:
+	dma_free_coherent(mgr->dev.parent, READ_DMA_SIZE, buf, dma_addr);
+
+	return status;
+}
+
+static int zynqmp_fpga_read_cfgreg(struct fpga_manager *mgr,
+				   struct seq_file *s)
+{
+	int ret = 0;
+	u32 val;
+	unsigned int *buf;
+	dma_addr_t dma_addr = 0;
+	struct zynqmp_fpga_priv *priv;
+	struct zynqmp_configreg *p = cfgreg;
+
+	priv = mgr->priv;
+
+	if (!(priv->feature_list & XILINX_ZYNQMP_PM_FPGA_READ_BACK))
+		return -EINVAL;
+
+	buf = dma_alloc_coherent(mgr->dev.parent, READ_DMA_SIZE,
+				 &dma_addr, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	seq_puts(s, "zynqMP FPGA Configuration register contents are\n");
+
+	while (p->reg) {
+		ret = zynqmp_pm_fpga_read(p->offset, dma_addr, readback_type,
+					  &val);
+		if (ret)
+			goto free_dmabuf;
+		seq_printf(s, "%s --> \t %x \t\r\n", p->reg, val);
+		p++;
+	}
+
+free_dmabuf:
+	dma_free_coherent(mgr->dev.parent, READ_DMA_SIZE, buf,
+			  dma_addr);
+
+	return ret;
+}
+
+static int zynqmp_fpga_read_cfgdata(struct fpga_manager *mgr,
+				    struct seq_file *s)
+{
+	struct zynqmp_fpga_priv *priv;
+	int ret;
+	u32 data_offset;
+	unsigned int *buf;
+	dma_addr_t dma_addr = 0;
+	size_t size;
+
+	priv = mgr->priv;
+
+	if (!(priv->feature_list & XILINX_ZYNQMP_PM_FPGA_REG_READ_BACK))
+		return -EINVAL;
+
+	size = priv->size + READ_DMA_SIZE + DUMMY_FRAMES_SIZE;
+
+	buf = dma_alloc_coherent(mgr->dev.parent, size, &dma_addr,
+				 GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	seq_puts(s, "zynqMP FPGA Configuration data contents are\n");
+	ret = zynqmp_pm_fpga_read((priv->size + DUMMY_FRAMES_SIZE) / 4,
+				  dma_addr, readback_type, &data_offset);
+	if (ret)
+		goto free_dmabuf;
+
+	seq_write(s, &buf[data_offset], priv->size);
+
+free_dmabuf:
+	dma_free_coherent(mgr->dev.parent, size, buf, dma_addr);
+
+	return ret;
+}
+
+static int zynqmp_fpga_ops_read(struct fpga_manager *mgr, struct seq_file *s)
+{
+	int ret;
+
+	if (readback_type)
+		ret = zynqmp_fpga_read_cfgdata(mgr, s);
+	else
+		ret = zynqmp_fpga_read_cfgreg(mgr, s);
+
+	return ret;
+}
+
 static const struct fpga_manager_ops zynqmp_fpga_ops = {
 	.state = zynqmp_fpga_ops_state,
+	.status = zynqmp_fpga_ops_status,
 	.write_init = zynqmp_fpga_ops_write_init,
 	.write = zynqmp_fpga_ops_write,
+	.write_sg = zynqmp_fpga_ops_write_sg,
+	.read = zynqmp_fpga_ops_read,
 };
 
 static int zynqmp_fpga_probe(struct platform_device *pdev)
@@ -95,6 +407,13 @@
 
 	priv->dev = dev;
 
+	if (!(zynqmp_pm_fpga_get_version(&priv->version))) {
+		if (zynqmp_pm_fpga_get_feature_list(&priv->feature_list))
+			priv->feature_list = DEFAULT_FEATURE_LIST;
+	} else {
+		priv->feature_list = DEFAULT_FEATURE_LIST;
+	}
+
 	mgr = devm_fpga_mgr_create(dev, "Xilinx ZynqMP FPGA Manager",
 				   &zynqmp_fpga_ops, priv);
 	if (!mgr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fsi/fsi-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fsi/fsi-core.c
@@ -1309,6 +1309,9 @@
 
 	mutex_init(&master->scan_lock);
 	master->idx = ida_simple_get(&master_ida, 0, INT_MAX, GFP_KERNEL);
+	if (master->idx < 0)
+		return master->idx;
+
 	dev_set_name(&master->dev, "fsi%d", master->idx);
 	master->dev.class = &fsi_master_class;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fsi/fsi-master-aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fsi/fsi-master-aspeed.c
@@ -453,6 +453,8 @@
 	gpiod_set_value(aspeed->cfam_reset_gpio, 1);
 	usleep_range(900, 1000);
 	gpiod_set_value(aspeed->cfam_reset_gpio, 0);
+	usleep_range(900, 1000);
+	opb_writel(aspeed, ctrl_base + FSI_MRESP0, cpu_to_be32(FSI_MRESP_RST_ALL_MASTER));
 	mutex_unlock(&aspeed->lock);
 
 	return count;
@@ -542,25 +544,28 @@
 		return rc;
 	}
 
-	aspeed = devm_kzalloc(&pdev->dev, sizeof(*aspeed), GFP_KERNEL);
+	aspeed = kzalloc(sizeof(*aspeed), GFP_KERNEL);
 	if (!aspeed)
 		return -ENOMEM;
 
 	aspeed->dev = &pdev->dev;
 
 	aspeed->base = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(aspeed->base))
-		return PTR_ERR(aspeed->base);
+	if (IS_ERR(aspeed->base)) {
+		rc = PTR_ERR(aspeed->base);
+		goto err_free_aspeed;
+	}
 
 	aspeed->clk = devm_clk_get(aspeed->dev, NULL);
 	if (IS_ERR(aspeed->clk)) {
 		dev_err(aspeed->dev, "couldn't get clock\n");
-		return PTR_ERR(aspeed->clk);
+		rc = PTR_ERR(aspeed->clk);
+		goto err_free_aspeed;
 	}
 	rc = clk_prepare_enable(aspeed->clk);
 	if (rc) {
 		dev_err(aspeed->dev, "couldn't enable clock\n");
-		return rc;
+		goto err_free_aspeed;
 	}
 
 	rc = setup_cfam_reset(aspeed);
@@ -595,7 +600,7 @@
 	rc = opb_readl(aspeed, ctrl_base + FSI_MVER, &raw);
 	if (rc) {
 		dev_err(&pdev->dev, "failed to read hub version\n");
-		return rc;
+		goto err_release;
 	}
 
 	reg = be32_to_cpu(raw);
@@ -634,6 +639,8 @@
 
 err_release:
 	clk_disable_unprepare(aspeed->clk);
+err_free_aspeed:
+	kfree(aspeed);
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fsi/fsi-master-ast-cf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fsi/fsi-master-ast-cf.c
@@ -1439,3 +1439,4 @@
 
 module_platform_driver(fsi_master_acf);
 MODULE_LICENSE("GPL");
+MODULE_FIRMWARE(FW_FILE_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fsi/fsi-occ.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fsi/fsi-occ.c
@@ -50,6 +50,7 @@
 	struct device *sbefifo;
 	char name[32];
 	int idx;
+	u8 sequence_number;
 	enum versions version;
 	struct miscdevice mdev;
 	struct mutex occ_lock;
@@ -141,8 +142,7 @@
 {
 	struct occ_client *client = file->private_data;
 	size_t rlen, data_length;
-	u16 checksum = 0;
-	ssize_t rc, i;
+	ssize_t rc;
 	u8 *cmd;
 
 	if (!client)
@@ -156,9 +156,6 @@
 	/* Construct the command */
 	cmd = client->buffer;
 
-	/* Sequence number (we could increment and compare with response) */
-	cmd[0] = 1;
-
 	/*
 	 * Copy the user command (assume user data follows the occ command
 	 * format)
@@ -178,14 +175,7 @@
 		goto done;
 	}
 
-	/* Calculate checksum */
-	for (i = 0; i < data_length + 4; ++i)
-		checksum += cmd[i];
-
-	cmd[data_length + 4] = checksum >> 8;
-	cmd[data_length + 5] = checksum & 0xFF;
-
-	/* Submit command */
+	/* Submit command; 4 bytes before the data and 2 bytes after */
 	rlen = PAGE_SIZE;
 	rc = fsi_occ_submit(client->occ->dev, cmd, data_length + 6, cmd,
 			    &rlen);
@@ -314,11 +304,13 @@
 	return rc;
 }
 
-static int occ_putsram(struct occ *occ, const void *data, ssize_t len)
+static int occ_putsram(struct occ *occ, const void *data, ssize_t len,
+		       u8 seq_no, u16 checksum)
 {
 	size_t cmd_len, buf_len, resp_len, resp_data_len;
 	u32 data_len = ((len + 7) / 8) * 8;	/* must be multiples of 8 B */
 	__be32 *buf;
+	u8 *byte_buf;
 	int idx = 0, rc;
 
 	cmd_len = (occ->version == occ_p10) ? 6 : 5;
@@ -358,6 +350,15 @@
 	buf[4 + idx] = cpu_to_be32(data_len);
 	memcpy(&buf[5 + idx], data, len);
 
+	byte_buf = (u8 *)&buf[5 + idx];
+	/*
+	 * Overwrite the first byte with our sequence number and the last two
+	 * bytes with the checksum.
+	 */
+	byte_buf[0] = seq_no;
+	byte_buf[len - 2] = checksum >> 8;
+	byte_buf[len - 1] = checksum & 0xff;
+
 	rc = sbefifo_submit(occ->sbefifo, buf, cmd_len, buf, &resp_len);
 	if (rc)
 		goto free;
@@ -467,9 +468,12 @@
 	struct occ *occ = dev_get_drvdata(dev);
 	struct occ_response *resp = response;
 	u8 seq_no;
+	u16 checksum = 0;
 	u16 resp_data_length;
+	const u8 *byte_request = (const u8 *)request;
 	unsigned long start;
 	int rc;
+	size_t i;
 
 	if (!occ)
 		return -ENODEV;
@@ -479,11 +483,26 @@
 		return -EINVAL;
 	}
 
+	/* Checksum the request, ignoring first byte (sequence number). */
+	for (i = 1; i < req_len - 2; ++i)
+		checksum += byte_request[i];
+
 	mutex_lock(&occ->occ_lock);
 
-	/* Extract the seq_no from the command (first byte) */
-	seq_no = *(const u8 *)request;
-	rc = occ_putsram(occ, request, req_len);
+	/*
+	 * Get a sequence number and update the counter. Avoid a sequence
+	 * number of 0 which would pass the response check below even if the
+	 * OCC response is uninitialized. Any sequence number the user is
+	 * trying to send is overwritten since this function is the only common
+	 * interface to the OCC and therefore the only place we can guarantee
+	 * unique sequence numbers.
+	 */
+	seq_no = occ->sequence_number++;
+	if (!occ->sequence_number)
+		occ->sequence_number = 1;
+	checksum += seq_no;
+
+	rc = occ_putsram(occ, request, req_len, seq_no, checksum);
 	if (rc)
 		goto done;
 
@@ -574,6 +593,7 @@
 	occ->version = (uintptr_t)of_device_get_match_data(dev);
 	occ->dev = dev;
 	occ->sbefifo = dev->parent;
+	occ->sequence_number = 1;
 	mutex_init(&occ->occ_lock);
 
 	if (dev->of_node) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fsi/fsi-sbefifo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fsi/fsi-sbefifo.c
@@ -640,7 +640,7 @@
 	}
         ffdc_iov.iov_base = ffdc;
 	ffdc_iov.iov_len = SBEFIFO_MAX_FFDC_SIZE;
-        iov_iter_kvec(&ffdc_iter, WRITE, &ffdc_iov, 1, SBEFIFO_MAX_FFDC_SIZE);
+        iov_iter_kvec(&ffdc_iter, READ, &ffdc_iov, 1, SBEFIFO_MAX_FFDC_SIZE);
 	cmd[0] = cpu_to_be32(2);
 	cmd[1] = cpu_to_be32(SBEFIFO_CMD_GET_SBE_FFDC);
 	rc = sbefifo_do_command(sbefifo, cmd, 2, &ffdc_iter);
@@ -737,7 +737,7 @@
 	rbytes = (*resp_len) * sizeof(__be32);
 	resp_iov.iov_base = response;
 	resp_iov.iov_len = rbytes;
-        iov_iter_kvec(&resp_iter, WRITE, &resp_iov, 1, rbytes);
+        iov_iter_kvec(&resp_iter, READ, &resp_iov, 1, rbytes);
 
 	/* Perform the command */
 	mutex_lock(&sbefifo->lock);
@@ -817,7 +817,7 @@
 	/* Prepare iov iterator */
 	resp_iov.iov_base = buf;
 	resp_iov.iov_len = len;
-	iov_iter_init(&resp_iter, WRITE, &resp_iov, 1, len);
+	iov_iter_init(&resp_iter, READ, &resp_iov, 1, len);
 
 	/* Perform the command */
 	mutex_lock(&sbefifo->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/fsi/fsi-scom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/fsi/fsi-scom.c
@@ -145,7 +145,7 @@
 				   uint64_t addr, uint32_t *status)
 {
 	uint64_t ind_data, ind_addr;
-	int rc, retries, err = 0;
+	int rc, err;
 
 	if (value & ~XSCOM_DATA_IND_DATA)
 		return -EINVAL;
@@ -156,19 +156,14 @@
 	if (rc || (*status & SCOM_STATUS_ANY_ERR))
 		return rc;
 
-	for (retries = 0; retries < SCOM_MAX_IND_RETRIES; retries++) {
-		rc = __get_scom(scom, &ind_data, addr, status);
-		if (rc || (*status & SCOM_STATUS_ANY_ERR))
-			return rc;
-
-		err = (ind_data & XSCOM_DATA_IND_ERR_MASK) >> XSCOM_DATA_IND_ERR_SHIFT;
-		*status = err << SCOM_STATUS_PIB_RESP_SHIFT;
-		if ((ind_data & XSCOM_DATA_IND_COMPLETE) || (err != SCOM_PIB_BLOCKED))
-			return 0;
+	rc = __get_scom(scom, &ind_data, addr, status);
+	if (rc || (*status & SCOM_STATUS_ANY_ERR))
+		return rc;
 
-		msleep(1);
-	}
-	return rc;
+	err = (ind_data & XSCOM_DATA_IND_ERR_MASK) >> XSCOM_DATA_IND_ERR_SHIFT;
+	*status = err << SCOM_STATUS_PIB_RESP_SHIFT;
+
+	return 0;
 }
 
 static int put_indirect_scom_form1(struct scom_device *scom, uint64_t value,
@@ -188,7 +183,7 @@
 				   uint64_t addr, uint32_t *status)
 {
 	uint64_t ind_data, ind_addr;
-	int rc, retries, err = 0;
+	int rc, err;
 
 	ind_addr = addr & XSCOM_ADDR_DIRECT_PART;
 	ind_data = (addr & XSCOM_ADDR_INDIRECT_PART) | XSCOM_DATA_IND_READ;
@@ -196,21 +191,15 @@
 	if (rc || (*status & SCOM_STATUS_ANY_ERR))
 		return rc;
 
-	for (retries = 0; retries < SCOM_MAX_IND_RETRIES; retries++) {
-		rc = __get_scom(scom, &ind_data, addr, status);
-		if (rc || (*status & SCOM_STATUS_ANY_ERR))
-			return rc;
-
-		err = (ind_data & XSCOM_DATA_IND_ERR_MASK) >> XSCOM_DATA_IND_ERR_SHIFT;
-		*status = err << SCOM_STATUS_PIB_RESP_SHIFT;
-		*value = ind_data & XSCOM_DATA_IND_DATA;
+	rc = __get_scom(scom, &ind_data, addr, status);
+	if (rc || (*status & SCOM_STATUS_ANY_ERR))
+		return rc;
 
-		if ((ind_data & XSCOM_DATA_IND_COMPLETE) || (err != SCOM_PIB_BLOCKED))
-			return 0;
+	err = (ind_data & XSCOM_DATA_IND_ERR_MASK) >> XSCOM_DATA_IND_ERR_SHIFT;
+	*status = err << SCOM_STATUS_PIB_RESP_SHIFT;
+	*value = ind_data & XSCOM_DATA_IND_DATA;
 
-		msleep(1);
-	}
-	return rc;
+	return 0;
 }
 
 static int raw_put_scom(struct scom_device *scom, uint64_t value,
@@ -289,7 +278,7 @@
 	int rc;
 
 	rc = raw_put_scom(scom, value, addr, &status);
-	if (rc == -ENODEV)
+	if (rc)
 		return rc;
 
 	rc = handle_fsi2pib_status(scom, status);
@@ -308,7 +297,7 @@
 	int rc;
 
 	rc = raw_get_scom(scom, value, addr, &status);
-	if (rc == -ENODEV)
+	if (rc)
 		return rc;
 
 	rc = handle_fsi2pib_status(scom, status);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/Kconfig
@@ -100,7 +100,7 @@
 	tristate
 
 config GPIO_REGMAP
-	depends on REGMAP
+	select REGMAP
 	tristate
 
 # put drivers in the right section, in alphabetical order
@@ -353,6 +353,17 @@
 	  IXP4xx series of chips.
 
 	  If unsure, say N.
+
+config GPIO_LJCA
+	tristate "INTEL La Jolla Cove Adapter GPIO support"
+	depends on MFD_LJCA
+	help
+	  Select this option to enable GPIO driver for the INTEL
+	  La Jolla Cove Adapter (LJCA) board.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called gpio-ljca.
+
 config GPIO_LOGICVC
 	tristate "Xylon LogiCVC GPIO support"
 	depends on MFD_SYSCON && OF
@@ -523,6 +534,7 @@
 config GPIO_ROCKCHIP
 	tristate "Rockchip GPIO support"
 	depends on ARCH_ROCKCHIP || COMPILE_TEST
+	select GENERIC_IRQ_CHIP
 	select GPIOLIB_IRQCHIP
 	default ARCH_ROCKCHIP
 	help
@@ -763,6 +775,18 @@
 	help
 	  Say yes here to support Xilinx Zynq GPIO controller.
 
+config GPIO_ZYNQMP_MODEPIN
+	tristate "ZynqMP ps-mode pin gpio configuration driver"
+	depends on ZYNQMP_FIRMWARE
+	default ZYNQMP_FIRMWARE
+	help
+	  Say yes here to support the ZynqMP ps-mode pin gpio configuration
+	  driver.
+
+	  This ps-mode pin gpio driver is based on GPIO framework, PS_MODE
+	  is 4-bits boot mode pins. It sets and gets the status of
+	  the ps-mode pin. Every pin can be configured as input/output.
+
 config GPIO_LOONGSON1
 	tristate "Loongson1 GPIO support"
 	depends on MACH_LOONGSON32
@@ -1018,6 +1042,12 @@
 	  Say yes here to enable the max732x to be used as an interrupt
 	  controller. It requires the driver to be built in the kernel.
 
+config GPIO_M058SSAN
+	tristate "M085 8-DI 8-DO I2C expander"
+	depends on UBUNTU_ODM_DRIVERS
+	help
+	  Say yes here to enable the M058SSAN gpio driver.
+
 config GPIO_PCA953X
 	tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
 	select REGMAP_I2C
@@ -1079,6 +1109,15 @@
 	  This driver provides an in-kernel interface to those GPIOs using
 	  platform-neutral GPIO calls.
 
+config GPIO_SLG7XL45106
+	tristate "SLG7XL45106 8-Bit I2C GPO expander"
+	help
+	  Say yes here to enable the GPO driver for the Dialog SLG7XL45106 chip.
+	  This expander has 8 output pins.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called gpio-slg7xl45106.
+
 config GPIO_TPIC2810
 	tristate "TPIC2810 8-Bit I2C GPO expander"
 	help
@@ -1395,7 +1434,7 @@
 	  drivers are loaded.
 
 config GPIO_TQMX86
-	tristate "TQ-Systems QTMX86 GPIO"
+	tristate "TQ-Systems TQMx86 GPIO"
 	depends on MFD_TQMX86 || COMPILE_TEST
 	depends on HAS_IOPORT_MAP
 	select GPIOLIB_IRQCHIP
@@ -1462,6 +1501,18 @@
 menu "PCI GPIO expanders"
 	depends on PCI
 
+config GPIO_AAEON
+	tristate "AAEON GPIO support"
+	depends on ASUS_WMI
+	depends on UBUNTU_ODM_DRIVERS
+	select MFD_AAEON
+	help
+	  Say yes here to support GPIO pins on Single Board Computers produced
+	  by AAEON.
+
+	  This driver leverages the ASUS WMI interface to access device
+	  resources.
+
 config GPIO_AMD8111
 	tristate "AMD 8111 GPIO driver"
 	depends on X86 || COMPILE_TEST
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/Makefile
@@ -23,6 +23,7 @@
 obj-$(CONFIG_GPIO_104_IDIO_16)		+= gpio-104-idio-16.o
 obj-$(CONFIG_GPIO_74X164)		+= gpio-74x164.o
 obj-$(CONFIG_GPIO_74XX_MMIO)		+= gpio-74xx-mmio.o
+obj-$(CONFIG_GPIO_AAEON)                += gpio-aaeon.o
 obj-$(CONFIG_GPIO_ADNP)			+= gpio-adnp.o
 obj-$(CONFIG_GPIO_ADP5520)		+= gpio-adp5520.o
 obj-$(CONFIG_GPIO_ADP5588)		+= gpio-adp5588.o
@@ -74,6 +75,7 @@
 obj-$(CONFIG_GPIO_IXP4XX)		+= gpio-ixp4xx.o
 obj-$(CONFIG_GPIO_JANZ_TTL)		+= gpio-janz-ttl.o
 obj-$(CONFIG_GPIO_KEMPLD)		+= gpio-kempld.o
+obj-$(CONFIG_GPIO_LJCA)			+= gpio-ljca.o
 obj-$(CONFIG_GPIO_LOGICVC)		+= gpio-logicvc.o
 obj-$(CONFIG_GPIO_LOONGSON1)		+= gpio-loongson1.o
 obj-$(CONFIG_GPIO_LOONGSON)		+= gpio-loongson.o
@@ -82,6 +84,7 @@
 obj-$(CONFIG_GPIO_LP87565)		+= gpio-lp87565.o
 obj-$(CONFIG_GPIO_LPC18XX)		+= gpio-lpc18xx.o
 obj-$(CONFIG_GPIO_LPC32XX)		+= gpio-lpc32xx.o
+obj-$(CONFIG_GPIO_M058SSAN)		+= gpio-m058ssan.o
 obj-$(CONFIG_GPIO_MADERA)		+= gpio-madera.o
 obj-$(CONFIG_GPIO_MAX3191X)		+= gpio-max3191x.o
 obj-$(CONFIG_GPIO_MAX7300)		+= gpio-max7300.o
@@ -135,6 +138,7 @@
 obj-$(CONFIG_GPIO_SIFIVE)		+= gpio-sifive.o
 obj-$(CONFIG_GPIO_SIOX)			+= gpio-siox.o
 obj-$(CONFIG_GPIO_SL28CPLD)		+= gpio-sl28cpld.o
+obj-$(CONFIG_GPIO_SLG7XL45106)		+= gpio-slg7xl45106.o
 obj-$(CONFIG_GPIO_SODAVILLE)		+= gpio-sodaville.o
 obj-$(CONFIG_GPIO_SPEAR_SPICS)		+= gpio-spear-spics.o
 obj-$(CONFIG_GPIO_SPRD)			+= gpio-sprd.o
@@ -184,3 +188,4 @@
 obj-$(CONFIG_GPIO_XTENSA)		+= gpio-xtensa.o
 obj-$(CONFIG_GPIO_ZEVIO)		+= gpio-zevio.o
 obj-$(CONFIG_GPIO_ZYNQ)			+= gpio-zynq.o
+obj-$(CONFIG_GPIO_ZYNQMP_MODEPIN)	+= gpio-zynqmp-modepin.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-74x164.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-74x164.c
@@ -127,8 +127,6 @@
 	if (IS_ERR(chip->gpiod_oe))
 		return PTR_ERR(chip->gpiod_oe);
 
-	gpiod_set_value_cansleep(chip->gpiod_oe, 1);
-
 	spi_set_drvdata(spi, chip);
 
 	chip->gpio_chip.label = spi->modalias;
@@ -153,6 +151,8 @@
 		goto exit_destroy;
 	}
 
+	gpiod_set_value_cansleep(chip->gpiod_oe, 1);
+
 	ret = gpiochip_add_data(&chip->gpio_chip, chip);
 	if (!ret)
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-aaeon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-aaeon.c
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * AAEON GPIO driver
+ * Copyright (c) 2021, AAEON Ltd.
+ *
+ * Author: Edward Lin <edward1_lin@aaeon.com.tw>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/acpi.h>
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_data/x86/asus-wmi.h>
+#include <linux/platform_device.h>
+
+#define DRVNAME "gpio_aaeon"
+#define ASUS_NB_WMI_EVENT_GUID   "0B3CBB35-E3C2-45ED-91C2-4C5A6D195D1C"
+#define AAEON_WMI_MGMT_GUID      "97845ED0-4E6D-11DE-8A39-0800200C9A66"
+
+#define GET_GPIO_NUMBER_ID       0x00010000
+#define GET_LEVEL_METHOD_ID      0x00010001
+#define SET_LEVEL_METHOD_ID      0x00010002
+#define GET_DIRECTION_METHOD_ID  0x00010003
+#define SET_DIRECTION_METHOD_ID  0x00010004
+#define GET_SIO_NUMBER_METHOD_ID 0xF0010
+
+struct aaeon_gpio_bank {
+	struct gpio_chip chip;
+	unsigned int regbase;
+	struct aaeon_gpio_data *data;
+};
+
+struct aaeon_gpio_data {
+	int nr_bank;
+	struct aaeon_gpio_bank *bank;
+};
+
+static int aaeon_gpio_get_number(void);
+static int aaeon_gpio_get_direction(struct gpio_chip *chip,
+				 unsigned int offset);
+static int aaeon_gpio_output_set_direction(struct gpio_chip *chip,
+				 unsigned int offset, int value);
+static int aaeon_gpio_input_set_direction(struct gpio_chip *chip,
+				 unsigned int offset);
+static int aaeon_gpio_get(struct gpio_chip *chip,
+				 unsigned int offset);
+static void aaeon_gpio_set(struct gpio_chip *chip, unsigned int offset,
+				 int value);
+
+#define AAEON_GPIO_BANK(_base, _ngpio, _regbase)			\
+{									\
+	.chip = {							\
+		.label            = DRVNAME,				\
+		.owner            = THIS_MODULE,			\
+		.get_direction    = aaeon_gpio_get_direction,		\
+		.direction_input  = aaeon_gpio_input_set_direction,     \
+		.direction_output = aaeon_gpio_output_set_direction,    \
+		.get              = aaeon_gpio_get,			\
+		.set              = aaeon_gpio_set,			\
+		.base             = _base,				\
+		.ngpio            = _ngpio,				\
+		.can_sleep        = true,				\
+	},								\
+	.regbase = _regbase,						\
+}
+
+static struct aaeon_gpio_bank aaeon_gpio_bank[] = {
+	AAEON_GPIO_BANK(0, 0, 0xF0),
+};
+
+static int aaeon_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	int err, retval;
+	u32 dev_id = 0x0;
+
+	dev_id |= offset;
+	err = asus_wmi_evaluate_method(GET_DIRECTION_METHOD_ID, dev_id,
+				       0, &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static int aaeon_gpio_input_set_direction(struct gpio_chip *chip,
+					  unsigned int offset)
+{
+	int err, retval;
+	u32 dev_id;
+
+	dev_id = BIT(16) | offset;
+	err = asus_wmi_evaluate_method(SET_DIRECTION_METHOD_ID, dev_id,
+				       0, &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static int aaeon_gpio_output_set_direction(struct gpio_chip *chip,
+					   unsigned int offset, int value)
+{
+	int err, retval;
+	u32 dev_id = 0x0;
+
+	dev_id |= offset;
+	err = asus_wmi_evaluate_method(SET_DIRECTION_METHOD_ID, dev_id,
+				       0, &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static int aaeon_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	int err, retval;
+	u32 dev_id = 0x0;
+
+	dev_id |= offset;
+	err = asus_wmi_evaluate_method(GET_LEVEL_METHOD_ID, dev_id, 0, &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static void aaeon_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			   int value)
+{
+	int retval;
+	u32 dev_id = offset;
+
+	if (value)
+		dev_id = BIT(16) | dev_id;
+
+	asus_wmi_evaluate_method(SET_LEVEL_METHOD_ID, dev_id, 0, &retval);
+}
+
+static int aaeon_gpio_get_number(void)
+{
+	int err, retval;
+
+	err = asus_wmi_evaluate_method(GET_GPIO_NUMBER_ID,
+				       GET_SIO_NUMBER_METHOD_ID,
+				       0, &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static int __init aaeon_gpio_probe(struct platform_device *pdev)
+{
+	int err, i;
+	int dio_number = 0;
+	struct aaeon_gpio_data *data;
+	struct aaeon_gpio_bank *bank;
+
+	/* Prevent other drivers adding this platfom device */
+	if (!wmi_has_guid(AAEON_WMI_MGMT_GUID)) {
+		pr_debug("AAEON Management GUID not found\n");
+		return -ENODEV;
+	}
+
+	dio_number = aaeon_gpio_get_number();
+	if (dio_number < 0)
+		return -ENODEV;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->nr_bank = ARRAY_SIZE(aaeon_gpio_bank);
+	data->bank = aaeon_gpio_bank;
+	platform_set_drvdata(pdev, data);
+	bank = &data->bank[0];
+	bank->chip.parent = &pdev->dev;
+	bank->chip.ngpio = dio_number;
+	bank->data = data;
+	err = devm_gpiochip_add_data(&pdev->dev, &bank->chip, bank);
+	if (err)
+		pr_debug("Failed to register gpiochip %d: %d\n", i, err);
+
+	return err;
+}
+
+static struct platform_driver aaeon_gpio_driver = {
+	.driver = {
+		.name = "gpio-aaeon",
+	},
+};
+
+module_platform_driver_probe(aaeon_gpio_driver, aaeon_gpio_probe);
+
+MODULE_ALIAS("platform:gpio-aaeon");
+MODULE_DESCRIPTION("AAEON GPIO Driver");
+MODULE_AUTHOR("Edward Lin <edward1_lin@aaeon.com.tw>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-aggregator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-aggregator.c
@@ -116,10 +116,15 @@
 	struct platform_device *pdev;
 	int res, id;
 
+	if (!try_module_get(THIS_MODULE))
+		return -ENOENT;
+
 	/* kernfs guarantees string termination, so count + 1 is safe */
 	aggr = kzalloc(sizeof(*aggr) + count + 1, GFP_KERNEL);
-	if (!aggr)
-		return -ENOMEM;
+	if (!aggr) {
+		res = -ENOMEM;
+		goto put_module;
+	}
 
 	memcpy(aggr->args, buf, count + 1);
 
@@ -158,6 +163,7 @@
 	}
 
 	aggr->pdev = pdev;
+	module_put(THIS_MODULE);
 	return count;
 
 remove_table:
@@ -172,6 +178,8 @@
 	kfree(aggr->lookups);
 free_ga:
 	kfree(aggr);
+put_module:
+	module_put(THIS_MODULE);
 	return res;
 }
 
@@ -200,13 +208,19 @@
 	if (error)
 		return error;
 
+	if (!try_module_get(THIS_MODULE))
+		return -ENOENT;
+
 	mutex_lock(&gpio_aggregator_lock);
 	aggr = idr_remove(&gpio_aggregator_idr, id);
 	mutex_unlock(&gpio_aggregator_lock);
-	if (!aggr)
+	if (!aggr) {
+		module_put(THIS_MODULE);
 		return -ENOENT;
+	}
 
 	gpio_aggregator_free(aggr);
+	module_put(THIS_MODULE);
 	return count;
 }
 static DRIVER_ATTR_WO(delete_device);
@@ -273,7 +287,8 @@
 {
 	struct gpiochip_fwd *fwd = gpiochip_get_data(chip);
 
-	return gpiod_get_value(fwd->descs[offset]);
+	return chip->can_sleep ? gpiod_get_value_cansleep(fwd->descs[offset])
+			       : gpiod_get_value(fwd->descs[offset]);
 }
 
 static int gpio_fwd_get_multiple(struct gpiochip_fwd *fwd, unsigned long *mask,
@@ -292,7 +307,10 @@
 	for_each_set_bit(i, mask, fwd->chip.ngpio)
 		descs[j++] = fwd->descs[i];
 
-	error = gpiod_get_array_value(j, descs, NULL, values);
+	if (fwd->chip.can_sleep)
+		error = gpiod_get_array_value_cansleep(j, descs, NULL, values);
+	else
+		error = gpiod_get_array_value(j, descs, NULL, values);
 	if (error)
 		return error;
 
@@ -327,7 +345,10 @@
 {
 	struct gpiochip_fwd *fwd = gpiochip_get_data(chip);
 
-	gpiod_set_value(fwd->descs[offset], value);
+	if (chip->can_sleep)
+		gpiod_set_value_cansleep(fwd->descs[offset], value);
+	else
+		gpiod_set_value(fwd->descs[offset], value);
 }
 
 static void gpio_fwd_set_multiple(struct gpiochip_fwd *fwd, unsigned long *mask,
@@ -346,7 +367,10 @@
 		descs[j++] = fwd->descs[i];
 	}
 
-	gpiod_set_array_value(j, descs, NULL, values);
+	if (fwd->chip.can_sleep)
+		gpiod_set_array_value_cansleep(j, descs, NULL, values);
+	else
+		gpiod_set_array_value(j, descs, NULL, values);
 }
 
 static void gpio_fwd_set_multiple_locked(struct gpio_chip *chip,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-amd8111.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-amd8111.c
@@ -226,7 +226,10 @@
 		ioport_unmap(gp.pm);
 		goto out;
 	}
+	return 0;
+
 out:
+	pci_dev_put(pdev);
 	return err;
 }
 
@@ -234,6 +237,7 @@
 {
 	gpiochip_remove(&gp.chip);
 	ioport_unmap(gp.pm);
+	pci_dev_put(gp.pdev);
 }
 
 module_init(amd_gpio_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-amdpt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-amdpt.c
@@ -35,19 +35,19 @@
 
 	dev_dbg(gc->parent, "pt_gpio_request offset=%x\n", offset);
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	using_pins = readl(pt_gpio->reg_base + PT_SYNC_REG);
 	if (using_pins & BIT(offset)) {
 		dev_warn(gc->parent, "PT GPIO pin %x reconfigured\n",
 			 offset);
-		spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+		raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 		return -EINVAL;
 	}
 
 	writel(using_pins | BIT(offset), pt_gpio->reg_base + PT_SYNC_REG);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
@@ -58,13 +58,13 @@
 	unsigned long flags;
 	u32 using_pins;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	using_pins = readl(pt_gpio->reg_base + PT_SYNC_REG);
 	using_pins &= ~BIT(offset);
 	writel(using_pins, pt_gpio->reg_base + PT_SYNC_REG);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	dev_dbg(gc->parent, "pt_gpio_free offset=%x\n", offset);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-aspeed-sgpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-aspeed-sgpio.c
@@ -31,7 +31,7 @@
 	struct gpio_chip chip;
 	struct irq_chip intc;
 	struct clk *pclk;
-	spinlock_t lock;
+	raw_spinlock_t lock;
 	void __iomem *base;
 	int irq;
 };
@@ -173,12 +173,12 @@
 	enum aspeed_sgpio_reg reg;
 	int rc = 0;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = aspeed_sgpio_is_input(offset) ? reg_val : reg_rdata;
 	rc = !!(ioread32(bank_reg(gpio, bank, reg)) & GPIO_BIT(offset));
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -215,11 +215,11 @@
 	struct aspeed_sgpio *gpio = gpiochip_get_data(gc);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	sgpio_set_value(gc, offset, val);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static int aspeed_sgpio_dir_in(struct gpio_chip *gc, unsigned int offset)
@@ -236,9 +236,9 @@
 	/* No special action is required for setting the direction; we'll
 	 * error-out in sgpio_set_value if this isn't an output GPIO */
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	rc = sgpio_set_value(gc, offset, val);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -277,11 +277,11 @@
 
 	status_addr = bank_reg(gpio, bank, reg_irq_status);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	iowrite32(bit, status_addr);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_sgpio_irq_set_mask(struct irq_data *d, bool set)
@@ -296,7 +296,7 @@
 	irqd_to_aspeed_sgpio_data(d, &gpio, &bank, &bit, &offset);
 	addr = bank_reg(gpio, bank, reg_irq_enable);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = ioread32(addr);
 	if (set)
@@ -306,7 +306,7 @@
 
 	iowrite32(reg, addr);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_sgpio_irq_mask(struct irq_data *d)
@@ -355,7 +355,7 @@
 		return -EINVAL;
 	}
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	addr = bank_reg(gpio, bank, reg_irq_type0);
 	reg = ioread32(addr);
@@ -372,7 +372,7 @@
 	reg = (reg & ~bit) | type2;
 	iowrite32(reg, addr);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	irq_set_handler_locked(d, handler);
 
@@ -395,7 +395,7 @@
 		reg = ioread32(bank_reg(data, bank, reg_irq_status));
 
 		for_each_set_bit(p, &reg, 32)
-			generic_handle_domain_irq(gc->irq.domain, i * 32 + p * 2);
+			generic_handle_domain_irq(gc->irq.domain, (i * 32 + p) * 2);
 	}
 
 	chained_irq_exit(ic, desc);
@@ -467,7 +467,7 @@
 
 	reg = bank_reg(gpio, to_bank(offset), reg_tolerance);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	val = readl(reg);
 
@@ -478,7 +478,7 @@
 
 	writel(val, reg);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -575,7 +575,7 @@
 	iowrite32(FIELD_PREP(ASPEED_SGPIO_CLK_DIV_MASK, sgpio_clk_div) | gpio_cnt_regval |
 		  ASPEED_SGPIO_ENABLE, gpio->base + ASPEED_SGPIO_CTRL);
 
-	spin_lock_init(&gpio->lock);
+	raw_spin_lock_init(&gpio->lock);
 
 	gpio->chip.parent = &pdev->dev;
 	gpio->chip.ngpio = nr_gpios * 2;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-aspeed.c
@@ -53,7 +53,7 @@
 struct aspeed_gpio {
 	struct gpio_chip chip;
 	struct irq_chip irqc;
-	spinlock_t lock;
+	raw_spinlock_t lock;
 	void __iomem *base;
 	int irq;
 	const struct aspeed_gpio_config *config;
@@ -404,6 +404,8 @@
 	gpio->dcache[GPIO_BANK(offset)] = reg;
 
 	iowrite32(reg, addr);
+	/* Flush write */
+	ioread32(addr);
 }
 
 static void aspeed_gpio_set(struct gpio_chip *gc, unsigned int offset,
@@ -413,14 +415,14 @@
 	unsigned long flags;
 	bool copro;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	__aspeed_gpio_set(gc, offset, val);
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static int aspeed_gpio_dir_in(struct gpio_chip *gc, unsigned int offset)
@@ -435,7 +437,7 @@
 	if (!have_input(gpio, offset))
 		return -ENOTSUPP;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = ioread32(addr);
 	reg &= ~GPIO_BIT(offset);
@@ -445,7 +447,7 @@
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -463,7 +465,7 @@
 	if (!have_output(gpio, offset))
 		return -ENOTSUPP;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = ioread32(addr);
 	reg |= GPIO_BIT(offset);
@@ -474,7 +476,7 @@
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -492,11 +494,11 @@
 	if (!have_output(gpio, offset))
 		return GPIO_LINE_DIRECTION_IN;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	val = ioread32(bank_reg(gpio, bank, reg_dir)) & GPIO_BIT(offset);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return val ? GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN;
 }
@@ -539,14 +541,14 @@
 
 	status_addr = bank_reg(gpio, bank, reg_irq_status);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	iowrite32(bit, status_addr);
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_gpio_irq_set_mask(struct irq_data *d, bool set)
@@ -565,7 +567,7 @@
 
 	addr = bank_reg(gpio, bank, reg_irq_enable);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	reg = ioread32(addr);
@@ -577,7 +579,7 @@
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_gpio_irq_mask(struct irq_data *d)
@@ -629,7 +631,7 @@
 		return -EINVAL;
 	}
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	addr = bank_reg(gpio, bank, reg_irq_type0);
@@ -649,7 +651,7 @@
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	irq_set_handler_locked(d, handler);
 
@@ -716,7 +718,7 @@
 
 	treg = bank_reg(gpio, to_bank(offset), reg_tolerance);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	val = readl(treg);
@@ -730,7 +732,7 @@
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -856,7 +858,7 @@
 		return rc;
 	}
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	if (timer_allocation_registered(gpio, offset)) {
 		rc = unregister_allocated_timer(gpio, offset);
@@ -916,7 +918,7 @@
 	configure_timer(gpio, offset, i);
 
 out:
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -927,13 +929,13 @@
 	unsigned long flags;
 	int rc;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	rc = unregister_allocated_timer(gpio, offset);
 	if (!rc)
 		configure_timer(gpio, offset, 0);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -963,7 +965,7 @@
 	else if (param == PIN_CONFIG_BIAS_DISABLE ||
 			param == PIN_CONFIG_BIAS_PULL_DOWN ||
 			param == PIN_CONFIG_DRIVE_STRENGTH)
-		return pinctrl_gpio_set_config(offset, config);
+		return pinctrl_gpio_set_config(chip->base + offset, config);
 	else if (param == PIN_CONFIG_DRIVE_OPEN_DRAIN ||
 			param == PIN_CONFIG_DRIVE_OPEN_SOURCE)
 		/* Return -ENOTSUPP to trigger emulation, as per datasheet */
@@ -1015,7 +1017,7 @@
 		return -EINVAL;
 	bindex = offset >> 3;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	/* Sanity check, this shouldn't happen */
 	if (gpio->cf_copro_bankmap[bindex] == 0xff) {
@@ -1036,7 +1038,7 @@
 	if (bit)
 		*bit = GPIO_OFFSET(offset);
  bail:
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 	return rc;
 }
 EXPORT_SYMBOL_GPL(aspeed_gpio_copro_grab_gpio);
@@ -1060,7 +1062,7 @@
 		return -EINVAL;
 	bindex = offset >> 3;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	/* Sanity check, this shouldn't happen */
 	if (gpio->cf_copro_bankmap[bindex] == 0) {
@@ -1074,7 +1076,7 @@
 		aspeed_gpio_change_cmd_source(gpio, bank, bindex,
 					      GPIO_CMDSRC_ARM);
  bail:
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 	return rc;
 }
 EXPORT_SYMBOL_GPL(aspeed_gpio_copro_release_gpio);
@@ -1148,13 +1150,13 @@
 	if (IS_ERR(gpio->base))
 		return PTR_ERR(gpio->base);
 
-	spin_lock_init(&gpio->lock);
+	raw_spin_lock_init(&gpio->lock);
 
 	gpio_id = of_match_node(aspeed_gpio_of_table, pdev->dev.of_node);
 	if (!gpio_id)
 		return -EINVAL;
 
-	gpio->clk = of_clk_get(pdev->dev.of_node, 0);
+	gpio->clk = devm_clk_get_enabled(&pdev->dev, NULL);
 	if (IS_ERR(gpio->clk)) {
 		dev_warn(&pdev->dev,
 				"Failed to get clock from devicetree, debouncing disabled\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-bcm-kona.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-bcm-kona.c
@@ -76,6 +76,22 @@
 struct bcm_kona_gpio_bank {
 	int id;
 	int irq;
+	/*
+	 * Used to keep track of lock/unlock operations for each GPIO in the
+	 * bank.
+	 *
+	 * All GPIOs are locked by default (see bcm_kona_gpio_reset), and the
+	 * unlock count for all GPIOs is 0 by default. Each unlock increments
+	 * the counter, and each lock decrements the counter.
+	 *
+	 * The lock function only locks the GPIO once its unlock counter is
+	 * down to 0. This is necessary because the GPIO is unlocked in two
+	 * places in this driver: once for requested GPIOs, and once for
+	 * requested IRQs. Since it is possible for a GPIO to be requested
+	 * as both a GPIO and an IRQ, we need to ensure that we don't lock it
+	 * too early.
+	 */
+	u8 gpio_unlock_count[GPIO_PER_BANK];
 	/* Used in the interrupt handler */
 	struct bcm_kona_gpio *kona_gpio;
 };
@@ -93,14 +109,24 @@
 	u32 val;
 	unsigned long flags;
 	int bank_id = GPIO_BANK(gpio);
+	int bit = GPIO_BIT(gpio);
+	struct bcm_kona_gpio_bank *bank = &kona_gpio->banks[bank_id];
 
-	raw_spin_lock_irqsave(&kona_gpio->lock, flags);
+	if (bank->gpio_unlock_count[bit] == 0) {
+		dev_err(kona_gpio->gpio_chip.parent,
+			"Unbalanced locks for GPIO %u\n", gpio);
+		return;
+	}
 
-	val = readl(kona_gpio->reg_base + GPIO_PWD_STATUS(bank_id));
-	val |= BIT(gpio);
-	bcm_kona_gpio_write_lock_regs(kona_gpio->reg_base, bank_id, val);
+	if (--bank->gpio_unlock_count[bit] == 0) {
+		raw_spin_lock_irqsave(&kona_gpio->lock, flags);
 
-	raw_spin_unlock_irqrestore(&kona_gpio->lock, flags);
+		val = readl(kona_gpio->reg_base + GPIO_PWD_STATUS(bank_id));
+		val |= BIT(bit);
+		bcm_kona_gpio_write_lock_regs(kona_gpio->reg_base, bank_id, val);
+
+		raw_spin_unlock_irqrestore(&kona_gpio->lock, flags);
+	}
 }
 
 static void bcm_kona_gpio_unlock_gpio(struct bcm_kona_gpio *kona_gpio,
@@ -109,14 +135,20 @@
 	u32 val;
 	unsigned long flags;
 	int bank_id = GPIO_BANK(gpio);
+	int bit = GPIO_BIT(gpio);
+	struct bcm_kona_gpio_bank *bank = &kona_gpio->banks[bank_id];
 
-	raw_spin_lock_irqsave(&kona_gpio->lock, flags);
+	if (bank->gpio_unlock_count[bit] == 0) {
+		raw_spin_lock_irqsave(&kona_gpio->lock, flags);
 
-	val = readl(kona_gpio->reg_base + GPIO_PWD_STATUS(bank_id));
-	val &= ~BIT(gpio);
-	bcm_kona_gpio_write_lock_regs(kona_gpio->reg_base, bank_id, val);
+		val = readl(kona_gpio->reg_base + GPIO_PWD_STATUS(bank_id));
+		val &= ~BIT(bit);
+		bcm_kona_gpio_write_lock_regs(kona_gpio->reg_base, bank_id, val);
 
-	raw_spin_unlock_irqrestore(&kona_gpio->lock, flags);
+		raw_spin_unlock_irqrestore(&kona_gpio->lock, flags);
+	}
+
+	++bank->gpio_unlock_count[bit];
 }
 
 static int bcm_kona_gpio_get_dir(struct gpio_chip *chip, unsigned gpio)
@@ -367,6 +399,7 @@
 
 	kona_gpio = irq_data_get_irq_chip_data(d);
 	reg_base = kona_gpio->reg_base;
+
 	raw_spin_lock_irqsave(&kona_gpio->lock, flags);
 
 	val = readl(reg_base + GPIO_INT_MASK(bank_id));
@@ -389,6 +422,7 @@
 
 	kona_gpio = irq_data_get_irq_chip_data(d);
 	reg_base = kona_gpio->reg_base;
+
 	raw_spin_lock_irqsave(&kona_gpio->lock, flags);
 
 	val = readl(reg_base + GPIO_INT_MSKCLR(bank_id));
@@ -484,15 +518,26 @@
 static int bcm_kona_gpio_irq_reqres(struct irq_data *d)
 {
 	struct bcm_kona_gpio *kona_gpio = irq_data_get_irq_chip_data(d);
+	unsigned int gpio = d->hwirq;
 
-	return gpiochip_reqres_irq(&kona_gpio->gpio_chip, d->hwirq);
+	/*
+	 * We need to unlock the GPIO before any other operations are performed
+	 * on the relevant GPIO configuration registers
+	 */
+	bcm_kona_gpio_unlock_gpio(kona_gpio, gpio);
+
+	return gpiochip_reqres_irq(&kona_gpio->gpio_chip, gpio);
 }
 
 static void bcm_kona_gpio_irq_relres(struct irq_data *d)
 {
 	struct bcm_kona_gpio *kona_gpio = irq_data_get_irq_chip_data(d);
+	unsigned int gpio = d->hwirq;
+
+	/* Once we no longer use it, lock the GPIO again */
+	bcm_kona_gpio_lock_gpio(kona_gpio, gpio);
 
-	gpiochip_relres_irq(&kona_gpio->gpio_chip, d->hwirq);
+	gpiochip_relres_irq(&kona_gpio->gpio_chip, gpio);
 }
 
 static struct irq_chip bcm_gpio_irq_chip = {
@@ -630,7 +675,7 @@
 		bank->irq = platform_get_irq(pdev, i);
 		bank->kona_gpio = kona_gpio;
 		if (bank->irq < 0) {
-			dev_err(dev, "Couldn't get IRQ for bank %d", i);
+			dev_err(dev, "Couldn't get IRQ for bank %d\n", i);
 			ret = -ENOENT;
 			goto err_irq_domain;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-brcmstb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-brcmstb.c
@@ -92,9 +92,9 @@
 	unsigned long status;
 	unsigned long flags;
 
-	spin_lock_irqsave(&bank->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&bank->gc.bgpio_lock, flags);
 	status = __brcmstb_gpio_get_active_irqs(bank);
-	spin_unlock_irqrestore(&bank->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&bank->gc.bgpio_lock, flags);
 
 	return status;
 }
@@ -114,14 +114,14 @@
 	u32 imask;
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	imask = gc->read_reg(priv->reg_base + GIO_MASK(bank->id));
 	if (enable)
 		imask |= mask;
 	else
 		imask &= ~mask;
 	gc->write_reg(priv->reg_base + GIO_MASK(bank->id), imask);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static int brcmstb_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
@@ -204,7 +204,7 @@
 		return -EINVAL;
 	}
 
-	spin_lock_irqsave(&bank->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&bank->gc.bgpio_lock, flags);
 
 	iedge_config = bank->gc.read_reg(priv->reg_base +
 			GIO_EC(bank->id)) & ~mask;
@@ -220,7 +220,7 @@
 	bank->gc.write_reg(priv->reg_base + GIO_LEVEL(bank->id),
 			ilevel | level);
 
-	spin_unlock_irqrestore(&bank->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&bank->gc.bgpio_lock, flags);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-cadence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-cadence.c
@@ -41,12 +41,12 @@
 	struct cdns_gpio_chip *cgpio = gpiochip_get_data(chip);
 	unsigned long flags;
 
-	spin_lock_irqsave(&chip->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->bgpio_lock, flags);
 
 	iowrite32(ioread32(cgpio->regs + CDNS_GPIO_BYPASS_MODE) & ~BIT(offset),
 		  cgpio->regs + CDNS_GPIO_BYPASS_MODE);
 
-	spin_unlock_irqrestore(&chip->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->bgpio_lock, flags);
 	return 0;
 }
 
@@ -55,13 +55,13 @@
 	struct cdns_gpio_chip *cgpio = gpiochip_get_data(chip);
 	unsigned long flags;
 
-	spin_lock_irqsave(&chip->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->bgpio_lock, flags);
 
 	iowrite32(ioread32(cgpio->regs + CDNS_GPIO_BYPASS_MODE) |
 		  (BIT(offset) & cgpio->bypass_orig),
 		  cgpio->regs + CDNS_GPIO_BYPASS_MODE);
 
-	spin_unlock_irqrestore(&chip->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->bgpio_lock, flags);
 }
 
 static void cdns_gpio_irq_mask(struct irq_data *d)
@@ -90,7 +90,7 @@
 	u32 mask = BIT(d->hwirq);
 	int ret = 0;
 
-	spin_lock_irqsave(&chip->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->bgpio_lock, flags);
 
 	int_value = ioread32(cgpio->regs + CDNS_GPIO_IRQ_VALUE) & ~mask;
 	int_type = ioread32(cgpio->regs + CDNS_GPIO_IRQ_TYPE) & ~mask;
@@ -115,7 +115,7 @@
 	iowrite32(int_type, cgpio->regs + CDNS_GPIO_IRQ_TYPE);
 
 err_irq_type:
-	spin_unlock_irqrestore(&chip->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->bgpio_lock, flags);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-crystalcove.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-crystalcove.c
@@ -91,7 +91,7 @@
 		case 0x5e:
 			return GPIOPANELCTL;
 		default:
-			return -EOPNOTSUPP;
+			return -ENOTSUPP;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-davinci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-davinci.c
@@ -227,6 +227,11 @@
 	else
 		nirq = DIV_ROUND_UP(ngpio, 16);
 
+	if (nirq > MAX_INT_PER_BANK) {
+		dev_err(dev, "Too many IRQs!\n");
+		return -EINVAL;
+	}
+
 	chips = devm_kzalloc(dev, sizeof(*chips), GFP_KERNEL);
 	if (!chips)
 		return -ENOMEM;
@@ -288,7 +293,7 @@
  * serve as EDMA event triggers.
  */
 
-static void gpio_irq_disable(struct irq_data *d)
+static void gpio_irq_mask(struct irq_data *d)
 {
 	struct davinci_gpio_regs __iomem *g = irq2regs(d);
 	uintptr_t mask = (uintptr_t)irq_data_get_irq_handler_data(d);
@@ -297,7 +302,7 @@
 	writel_relaxed(mask, &g->clr_rising);
 }
 
-static void gpio_irq_enable(struct irq_data *d)
+static void gpio_irq_unmask(struct irq_data *d)
 {
 	struct davinci_gpio_regs __iomem *g = irq2regs(d);
 	uintptr_t mask = (uintptr_t)irq_data_get_irq_handler_data(d);
@@ -323,10 +328,10 @@
 
 static struct irq_chip gpio_irqchip = {
 	.name		= "GPIO",
-	.irq_enable	= gpio_irq_enable,
-	.irq_disable	= gpio_irq_disable,
+	.irq_unmask	= gpio_irq_unmask,
+	.irq_mask	= gpio_irq_mask,
 	.irq_set_type	= gpio_irq_type,
-	.flags		= IRQCHIP_SET_TYPE_MASKED,
+	.flags		= IRQCHIP_SET_TYPE_MASKED | IRQCHIP_SKIP_SET_WAKE,
 };
 
 static void gpio_irq_handler(struct irq_desc *desc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-dln2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-dln2.c
@@ -46,6 +46,7 @@
 struct dln2_gpio {
 	struct platform_device *pdev;
 	struct gpio_chip gpio;
+	struct irq_chip irqchip;
 
 	/*
 	 * Cache pin direction to save us one transfer, since the hardware has
@@ -383,15 +384,6 @@
 	mutex_unlock(&dln2->irq_lock);
 }
 
-static struct irq_chip dln2_gpio_irqchip = {
-	.name = "dln2-irq",
-	.irq_mask = dln2_irq_mask,
-	.irq_unmask = dln2_irq_unmask,
-	.irq_set_type = dln2_irq_set_type,
-	.irq_bus_lock = dln2_irq_bus_lock,
-	.irq_bus_sync_unlock = dln2_irq_bus_unlock,
-};
-
 static void dln2_gpio_event(struct platform_device *pdev, u16 echo,
 			    const void *data, int len)
 {
@@ -473,8 +465,15 @@
 	dln2->gpio.direction_output = dln2_gpio_direction_output;
 	dln2->gpio.set_config = dln2_gpio_set_config;
 
+	dln2->irqchip.name = "dln2-irq",
+	dln2->irqchip.irq_mask = dln2_irq_mask,
+	dln2->irqchip.irq_unmask = dln2_irq_unmask,
+	dln2->irqchip.irq_set_type = dln2_irq_set_type,
+	dln2->irqchip.irq_bus_lock = dln2_irq_bus_lock,
+	dln2->irqchip.irq_bus_sync_unlock = dln2_irq_bus_unlock,
+
 	girq = &dln2->gpio.irq;
-	girq->chip = &dln2_gpio_irqchip;
+	girq->chip = &dln2->irqchip;
 	/* The event comes from the outside so no parent handler */
 	girq->parent_handler = NULL;
 	girq->num_parents = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-dwapb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-dwapb.c
@@ -242,9 +242,9 @@
 	u32 val = BIT(irqd_to_hwirq(d));
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	dwapb_write(gpio, GPIO_PORTA_EOI, val);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void dwapb_irq_mask(struct irq_data *d)
@@ -254,10 +254,10 @@
 	unsigned long flags;
 	u32 val;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	val = dwapb_read(gpio, GPIO_INTMASK) | BIT(irqd_to_hwirq(d));
 	dwapb_write(gpio, GPIO_INTMASK, val);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void dwapb_irq_unmask(struct irq_data *d)
@@ -267,38 +267,42 @@
 	unsigned long flags;
 	u32 val;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	val = dwapb_read(gpio, GPIO_INTMASK) & ~BIT(irqd_to_hwirq(d));
 	dwapb_write(gpio, GPIO_INTMASK, val);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void dwapb_irq_enable(struct irq_data *d)
 {
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 	struct dwapb_gpio *gpio = to_dwapb_gpio(gc);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
 	unsigned long flags;
 	u32 val;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
-	val = dwapb_read(gpio, GPIO_INTEN);
-	val |= BIT(irqd_to_hwirq(d));
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
+	val = dwapb_read(gpio, GPIO_INTEN) | BIT(hwirq);
 	dwapb_write(gpio, GPIO_INTEN, val);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	val = dwapb_read(gpio, GPIO_INTMASK) & ~BIT(hwirq);
+	dwapb_write(gpio, GPIO_INTMASK, val);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void dwapb_irq_disable(struct irq_data *d)
 {
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 	struct dwapb_gpio *gpio = to_dwapb_gpio(gc);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
 	unsigned long flags;
 	u32 val;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
-	val = dwapb_read(gpio, GPIO_INTEN);
-	val &= ~BIT(irqd_to_hwirq(d));
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
+	val = dwapb_read(gpio, GPIO_INTMASK) | BIT(hwirq);
+	dwapb_write(gpio, GPIO_INTMASK, val);
+	val = dwapb_read(gpio, GPIO_INTEN) & ~BIT(hwirq);
 	dwapb_write(gpio, GPIO_INTEN, val);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static int dwapb_irq_set_type(struct irq_data *d, u32 type)
@@ -308,7 +312,7 @@
 	irq_hw_number_t bit = irqd_to_hwirq(d);
 	unsigned long level, polarity, flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	level = dwapb_read(gpio, GPIO_INTTYPE_LEVEL);
 	polarity = dwapb_read(gpio, GPIO_INT_POLARITY);
 
@@ -343,7 +347,7 @@
 	dwapb_write(gpio, GPIO_INTTYPE_LEVEL, level);
 	if (type != IRQ_TYPE_EDGE_BOTH)
 		dwapb_write(gpio, GPIO_INT_POLARITY, polarity);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
@@ -373,7 +377,7 @@
 	unsigned long flags, val_deb;
 	unsigned long mask = BIT(offset);
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	val_deb = dwapb_read(gpio, GPIO_PORTA_DEBOUNCE);
 	if (debounce)
@@ -382,7 +386,7 @@
 		val_deb &= ~mask;
 	dwapb_write(gpio, GPIO_PORTA_DEBOUNCE, val_deb);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
@@ -653,10 +657,9 @@
 	gpio->clks[1].id = "db";
 	err = devm_clk_bulk_get_optional(gpio->dev, DWAPB_NR_CLOCKS,
 					 gpio->clks);
-	if (err) {
-		dev_err(gpio->dev, "Cannot get APB/Debounce clocks\n");
-		return err;
-	}
+	if (err)
+		return dev_err_probe(gpio->dev, err,
+				     "Cannot get APB/Debounce clocks\n");
 
 	err = clk_bulk_prepare_enable(DWAPB_NR_CLOCKS, gpio->clks);
 	if (err) {
@@ -739,7 +742,7 @@
 	unsigned long flags;
 	int i;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	for (i = 0; i < gpio->nr_ports; i++) {
 		unsigned int offset;
 		unsigned int idx = gpio->ports[i].idx;
@@ -766,7 +769,7 @@
 			dwapb_write(gpio, GPIO_INTMASK, ~ctx->wake_en);
 		}
 	}
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	clk_bulk_disable_unprepare(DWAPB_NR_CLOCKS, gpio->clks);
 
@@ -786,7 +789,7 @@
 		return err;
 	}
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	for (i = 0; i < gpio->nr_ports; i++) {
 		unsigned int offset;
 		unsigned int idx = gpio->ports[i].idx;
@@ -813,7 +816,7 @@
 			dwapb_write(gpio, GPIO_PORTA_EOI, 0xffffffff);
 		}
 	}
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-eic-sprd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-eic-sprd.c
@@ -318,20 +318,27 @@
 		switch (flow_type) {
 		case IRQ_TYPE_LEVEL_HIGH:
 			sprd_eic_update(chip, offset, SPRD_EIC_DBNC_IEV, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_DBNC_IC, 1);
 			break;
 		case IRQ_TYPE_LEVEL_LOW:
 			sprd_eic_update(chip, offset, SPRD_EIC_DBNC_IEV, 0);
+			sprd_eic_update(chip, offset, SPRD_EIC_DBNC_IC, 1);
 			break;
 		case IRQ_TYPE_EDGE_RISING:
 		case IRQ_TYPE_EDGE_FALLING:
 		case IRQ_TYPE_EDGE_BOTH:
 			state = sprd_eic_get(chip, offset);
-			if (state)
+			if (state) {
 				sprd_eic_update(chip, offset,
 						SPRD_EIC_DBNC_IEV, 0);
-			else
+				sprd_eic_update(chip, offset,
+						SPRD_EIC_DBNC_IC, 1);
+			} else {
 				sprd_eic_update(chip, offset,
 						SPRD_EIC_DBNC_IEV, 1);
+				sprd_eic_update(chip, offset,
+						SPRD_EIC_DBNC_IC, 1);
+			}
 			break;
 		default:
 			return -ENOTSUPP;
@@ -343,20 +350,27 @@
 		switch (flow_type) {
 		case IRQ_TYPE_LEVEL_HIGH:
 			sprd_eic_update(chip, offset, SPRD_EIC_LATCH_INTPOL, 0);
+			sprd_eic_update(chip, offset, SPRD_EIC_LATCH_INTCLR, 1);
 			break;
 		case IRQ_TYPE_LEVEL_LOW:
 			sprd_eic_update(chip, offset, SPRD_EIC_LATCH_INTPOL, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_LATCH_INTCLR, 1);
 			break;
 		case IRQ_TYPE_EDGE_RISING:
 		case IRQ_TYPE_EDGE_FALLING:
 		case IRQ_TYPE_EDGE_BOTH:
 			state = sprd_eic_get(chip, offset);
-			if (state)
+			if (state) {
 				sprd_eic_update(chip, offset,
 						SPRD_EIC_LATCH_INTPOL, 0);
-			else
+				sprd_eic_update(chip, offset,
+						SPRD_EIC_LATCH_INTCLR, 1);
+			} else {
 				sprd_eic_update(chip, offset,
 						SPRD_EIC_LATCH_INTPOL, 1);
+				sprd_eic_update(chip, offset,
+						SPRD_EIC_LATCH_INTCLR, 1);
+			}
 			break;
 		default:
 			return -ENOTSUPP;
@@ -370,29 +384,34 @@
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTMODE, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTPOL, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_edge_irq);
 			break;
 		case IRQ_TYPE_EDGE_FALLING:
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTMODE, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTPOL, 0);
+			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_edge_irq);
 			break;
 		case IRQ_TYPE_EDGE_BOTH:
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTMODE, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTBOTH, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_edge_irq);
 			break;
 		case IRQ_TYPE_LEVEL_HIGH:
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTMODE, 1);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTPOL, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_level_irq);
 			break;
 		case IRQ_TYPE_LEVEL_LOW:
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTMODE, 1);
 			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTPOL, 0);
+			sprd_eic_update(chip, offset, SPRD_EIC_ASYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_level_irq);
 			break;
 		default:
@@ -405,29 +424,34 @@
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTMODE, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTPOL, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_edge_irq);
 			break;
 		case IRQ_TYPE_EDGE_FALLING:
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTMODE, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTPOL, 0);
+			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_edge_irq);
 			break;
 		case IRQ_TYPE_EDGE_BOTH:
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTMODE, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTBOTH, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_edge_irq);
 			break;
 		case IRQ_TYPE_LEVEL_HIGH:
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTMODE, 1);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTPOL, 1);
+			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_level_irq);
 			break;
 		case IRQ_TYPE_LEVEL_LOW:
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTBOTH, 0);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTMODE, 1);
 			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTPOL, 0);
+			sprd_eic_update(chip, offset, SPRD_EIC_SYNC_INTCLR, 1);
 			irq_set_handler_locked(data, handle_level_irq);
 			break;
 		default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-exar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-exar.c
@@ -80,11 +80,13 @@
 	struct exar_gpio_chip *exar_gpio = gpiochip_get_data(chip);
 	unsigned int addr = exar_offset_to_lvl_addr(exar_gpio, offset);
 	unsigned int bit = exar_offset_to_bit(exar_gpio, offset);
+	unsigned int bit_value = value ? BIT(bit) : 0;
 
-	if (value)
-		regmap_set_bits(exar_gpio->regmap, addr, BIT(bit));
-	else
-		regmap_clear_bits(exar_gpio->regmap, addr, BIT(bit));
+	/*
+	 * regmap_write_bits() forces value to be written when an external
+	 * pull up/down might otherwise indicate value was already set.
+	 */
+	regmap_write_bits(exar_gpio->regmap, addr, BIT(bit), bit_value);
 }
 
 static int exar_direction_output(struct gpio_chip *chip, unsigned int offset,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-grgpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-grgpio.c
@@ -145,7 +145,7 @@
 		return -EINVAL;
 	}
 
-	spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 
 	ipol = priv->gc.read_reg(priv->regs + GRGPIO_IPOL) & ~mask;
 	iedge = priv->gc.read_reg(priv->regs + GRGPIO_IEDGE) & ~mask;
@@ -153,7 +153,7 @@
 	priv->gc.write_reg(priv->regs + GRGPIO_IPOL, ipol | pol);
 	priv->gc.write_reg(priv->regs + GRGPIO_IEDGE, iedge | edge);
 
-	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 
 	return 0;
 }
@@ -164,11 +164,11 @@
 	int offset = d->hwirq;
 	unsigned long flags;
 
-	spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 
 	grgpio_set_imask(priv, offset, 0);
 
-	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 }
 
 static void grgpio_irq_unmask(struct irq_data *d)
@@ -177,11 +177,11 @@
 	int offset = d->hwirq;
 	unsigned long flags;
 
-	spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 
 	grgpio_set_imask(priv, offset, 1);
 
-	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 }
 
 static struct irq_chip grgpio_irq_chip = {
@@ -199,7 +199,7 @@
 	int i;
 	int match = 0;
 
-	spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 
 	/*
 	 * For each gpio line, call its interrupt handler if it its underlying
@@ -215,7 +215,7 @@
 		}
 	}
 
-	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 
 	if (!match)
 		dev_warn(priv->dev, "No gpio line matched irq %d\n", irq);
@@ -247,13 +247,13 @@
 	dev_dbg(priv->dev, "Mapping irq %d for gpio line %d\n",
 		irq, offset);
 
-	spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 
 	/* Request underlying irq if not already requested */
 	lirq->irq = irq;
 	uirq = &priv->uirqs[lirq->index];
 	if (uirq->refcnt == 0) {
-		spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+		raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 		ret = request_irq(uirq->uirq, grgpio_irq_handler, 0,
 				  dev_name(priv->dev), priv);
 		if (ret) {
@@ -262,11 +262,11 @@
 				uirq->uirq);
 			return ret;
 		}
-		spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+		raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 	}
 	uirq->refcnt++;
 
-	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 
 	/* Setup irq  */
 	irq_set_chip_data(irq, priv);
@@ -290,7 +290,7 @@
 	irq_set_chip_and_handler(irq, NULL, NULL);
 	irq_set_chip_data(irq, NULL);
 
-	spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&priv->gc.bgpio_lock, flags);
 
 	/* Free underlying irq if last user unmapped */
 	index = -1;
@@ -309,13 +309,13 @@
 		uirq = &priv->uirqs[lirq->index];
 		uirq->refcnt--;
 		if (uirq->refcnt == 0) {
-			spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+			raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 			free_irq(uirq->uirq, priv);
 			return;
 		}
 	}
 
-	spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&priv->gc.bgpio_lock, flags);
 }
 
 static const struct irq_domain_ops grgpio_irq_domain_ops = {
@@ -328,6 +328,7 @@
 static int grgpio_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
+	struct device *dev = &ofdev->dev;
 	void  __iomem *regs;
 	struct gpio_chip *gc;
 	struct grgpio_priv *priv;
@@ -337,7 +338,7 @@
 	int size;
 	int i;
 
-	priv = devm_kzalloc(&ofdev->dev, sizeof(*priv), GFP_KERNEL);
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
 
@@ -346,29 +347,32 @@
 		return PTR_ERR(regs);
 
 	gc = &priv->gc;
-	err = bgpio_init(gc, &ofdev->dev, 4, regs + GRGPIO_DATA,
+	err = bgpio_init(gc, dev, 4, regs + GRGPIO_DATA,
 			 regs + GRGPIO_OUTPUT, NULL, regs + GRGPIO_DIR, NULL,
 			 BGPIOF_BIG_ENDIAN_BYTE_ORDER);
 	if (err) {
-		dev_err(&ofdev->dev, "bgpio_init() failed\n");
+		dev_err(dev, "bgpio_init() failed\n");
 		return err;
 	}
 
 	priv->regs = regs;
 	priv->imask = gc->read_reg(regs + GRGPIO_IMASK);
-	priv->dev = &ofdev->dev;
+	priv->dev = dev;
 
 	gc->of_node = np;
 	gc->owner = THIS_MODULE;
 	gc->to_irq = grgpio_to_irq;
-	gc->label = devm_kasprintf(&ofdev->dev, GFP_KERNEL, "%pOF", np);
+	gc->label = devm_kasprintf(dev, GFP_KERNEL, "%pOF", np);
+	if (!gc->label)
+		return -ENOMEM;
+
 	gc->base = -1;
 
 	err = of_property_read_u32(np, "nbits", &prop);
 	if (err || prop <= 0 || prop > GRGPIO_MAX_NGPIO) {
 		gc->ngpio = GRGPIO_MAX_NGPIO;
-		dev_dbg(&ofdev->dev,
-			"No or invalid nbits property: assume %d\n", gc->ngpio);
+		dev_dbg(dev, "No or invalid nbits property: assume %d\n",
+			gc->ngpio);
 	} else {
 		gc->ngpio = prop;
 	}
@@ -380,7 +384,7 @@
 	irqmap = (s32 *)of_get_property(np, "irqmap", &size);
 	if (irqmap) {
 		if (size < gc->ngpio) {
-			dev_err(&ofdev->dev,
+			dev_err(dev,
 				"irqmap shorter than ngpio (%d < %d)\n",
 				size, gc->ngpio);
 			return -EINVAL;
@@ -390,7 +394,7 @@
 						     &grgpio_irq_domain_ops,
 						     priv);
 		if (!priv->domain) {
-			dev_err(&ofdev->dev, "Could not add irq domain\n");
+			dev_err(dev, "Could not add irq domain\n");
 			return -EINVAL;
 		}
 
@@ -420,13 +424,13 @@
 
 	err = gpiochip_add_data(gc, priv);
 	if (err) {
-		dev_err(&ofdev->dev, "Could not add gpiochip\n");
+		dev_err(dev, "Could not add gpiochip\n");
 		if (priv->domain)
 			irq_domain_remove(priv->domain);
 		return err;
 	}
 
-	dev_info(&ofdev->dev, "regs=0x%p, base=%d, ngpio=%d, irqs=%s\n",
+	dev_info(dev, "regs=0x%p, base=%d, ngpio=%d, irqs=%s\n",
 		 priv->regs, gc->base, gc->ngpio, priv->domain ? "on" : "off");
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-hlwd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-hlwd.c
@@ -65,7 +65,7 @@
 	int hwirq;
 	u32 emulated_pending;
 
-	spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
 	pending = ioread32be(hlwd->regs + HW_GPIOB_INTFLAG);
 	pending &= ioread32be(hlwd->regs + HW_GPIOB_INTMASK);
 
@@ -93,7 +93,7 @@
 		/* Mark emulated interrupts as pending */
 		pending |= rising | falling;
 	}
-	spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
 
 	chained_irq_enter(chip, desc);
 
@@ -118,11 +118,11 @@
 	unsigned long flags;
 	u32 mask;
 
-	spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
 	mask = ioread32be(hlwd->regs + HW_GPIOB_INTMASK);
 	mask &= ~BIT(data->hwirq);
 	iowrite32be(mask, hlwd->regs + HW_GPIOB_INTMASK);
-	spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
 }
 
 static void hlwd_gpio_irq_unmask(struct irq_data *data)
@@ -132,11 +132,11 @@
 	unsigned long flags;
 	u32 mask;
 
-	spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
 	mask = ioread32be(hlwd->regs + HW_GPIOB_INTMASK);
 	mask |= BIT(data->hwirq);
 	iowrite32be(mask, hlwd->regs + HW_GPIOB_INTMASK);
-	spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
 }
 
 static void hlwd_gpio_irq_enable(struct irq_data *data)
@@ -173,7 +173,7 @@
 	unsigned long flags;
 	u32 level;
 
-	spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&hlwd->gpioc.bgpio_lock, flags);
 
 	hlwd->edge_emulation &= ~BIT(data->hwirq);
 
@@ -194,11 +194,11 @@
 		hlwd_gpio_irq_setup_emulation(hlwd, data->hwirq, flow_type);
 		break;
 	default:
-		spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
+		raw_spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
 		return -EINVAL;
 	}
 
-	spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&hlwd->gpioc.bgpio_lock, flags);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-idt3243x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-idt3243x.c
@@ -57,7 +57,7 @@
 	if (sense == IRQ_TYPE_NONE || (sense & IRQ_TYPE_EDGE_BOTH))
 		return -EINVAL;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	ilevel = readl(ctrl->gpio + IDT_GPIO_ILEVEL);
 	if (sense & IRQ_TYPE_LEVEL_HIGH)
@@ -68,7 +68,7 @@
 	writel(ilevel, ctrl->gpio + IDT_GPIO_ILEVEL);
 	irq_set_handler_locked(d, handle_level_irq);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 	return 0;
 }
 
@@ -86,12 +86,12 @@
 	struct idt_gpio_ctrl *ctrl = gpiochip_get_data(gc);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	ctrl->mask_cache |= BIT(d->hwirq);
 	writel(ctrl->mask_cache, ctrl->pic + IDT_PIC_IRQ_MASK);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void idt_gpio_unmask(struct irq_data *d)
@@ -100,12 +100,12 @@
 	struct idt_gpio_ctrl *ctrl = gpiochip_get_data(gc);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	ctrl->mask_cache &= ~BIT(d->hwirq);
 	writel(ctrl->mask_cache, ctrl->pic + IDT_PIC_IRQ_MASK);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static int idt_gpio_irq_init_hw(struct gpio_chip *gc)
@@ -132,7 +132,7 @@
 	struct device *dev = &pdev->dev;
 	struct gpio_irq_chip *girq;
 	struct idt_gpio_ctrl *ctrl;
-	unsigned int parent_irq;
+	int parent_irq;
 	int ngpios;
 	int ret;
 
@@ -164,8 +164,8 @@
 			return PTR_ERR(ctrl->pic);
 
 		parent_irq = platform_get_irq(pdev, 0);
-		if (!parent_irq)
-			return -EINVAL;
+		if (parent_irq < 0)
+			return parent_irq;
 
 		girq = &ctrl->gc.irq;
 		girq->chip = &idt_gpio_irqchip;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-ixp4xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-ixp4xx.c
@@ -128,7 +128,7 @@
 		int_reg = IXP4XX_REG_GPIT1;
 	}
 
-	spin_lock_irqsave(&g->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&g->gc.bgpio_lock, flags);
 
 	/* Clear the style for the appropriate pin */
 	val = __raw_readl(g->base + int_reg);
@@ -147,7 +147,7 @@
 	val |= BIT(d->hwirq);
 	__raw_writel(val, g->base + IXP4XX_REG_GPOE);
 
-	spin_unlock_irqrestore(&g->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&g->gc.bgpio_lock, flags);
 
 	/* This parent only accept level high (asserted) */
 	return irq_chip_set_type_parent(d, IRQ_TYPE_LEVEL_HIGH);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-ljca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-ljca.c
@@ -0,0 +1,468 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Intel La Jolla Cove Adapter USB-GPIO driver
+ *
+ * Copyright (c) 2021, Intel Corporation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/gpio/driver.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/kref.h>
+#include <linux/mfd/ljca.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/bitops.h>
+
+#define GPIO_PAYLOAD_LEN(pin_num)                                              \
+	(sizeof(struct gpio_packet) + (pin_num) * sizeof(struct gpio_op))
+
+/* GPIO commands */
+#define GPIO_CONFIG 1
+#define GPIO_READ 2
+#define GPIO_WRITE 3
+#define GPIO_INT_EVENT 4
+#define GPIO_INT_MASK 5
+#define GPIO_INT_UNMASK 6
+
+#define GPIO_CONF_DISABLE BIT(0)
+#define GPIO_CONF_INPUT BIT(1)
+#define GPIO_CONF_OUTPUT BIT(2)
+#define GPIO_CONF_PULLUP BIT(3)
+#define GPIO_CONF_PULLDOWN BIT(4)
+#define GPIO_CONF_DEFAULT BIT(5)
+#define GPIO_CONF_INTERRUPT BIT(6)
+#define GPIO_INT_TYPE BIT(7)
+
+#define GPIO_CONF_EDGE (1 << 7)
+#define GPIO_CONF_LEVEL (0 << 7)
+
+/* Intentional overlap with PULLUP / PULLDOWN */
+#define GPIO_CONF_SET BIT(3)
+#define GPIO_CONF_CLR BIT(4)
+
+struct gpio_op {
+	u8 index;
+	u8 value;
+} __packed;
+
+struct gpio_packet {
+	u8 num;
+	struct gpio_op item[];
+} __packed;
+
+struct ljca_gpio_dev {
+	struct platform_device *pdev;
+	struct gpio_chip gc;
+	struct ljca_gpio_info *ctr_info;
+	DECLARE_BITMAP(unmasked_irqs, MAX_GPIO_NUM);
+	DECLARE_BITMAP(enabled_irqs, MAX_GPIO_NUM);
+	DECLARE_BITMAP(reenable_irqs, MAX_GPIO_NUM);
+	u8 *connect_mode;
+	struct mutex irq_lock;
+	struct work_struct work;
+	struct mutex trans_lock;
+
+	u8 obuf[256];
+	u8 ibuf[256];
+};
+
+static bool ljca_gpio_valid(struct ljca_gpio_dev *ljca_gpio, int gpio_id)
+{
+	if (gpio_id >= ljca_gpio->ctr_info->num ||
+	    !test_bit(gpio_id, ljca_gpio->ctr_info->valid_pin_map)) {
+		dev_err(&ljca_gpio->pdev->dev,
+			"invalid gpio gpio_id gpio_id:%d\n", gpio_id);
+		return false;
+	}
+
+	return true;
+}
+
+static int gpio_config(struct ljca_gpio_dev *ljca_gpio, u8 gpio_id, u8 config)
+{
+	struct gpio_packet *packet = (struct gpio_packet *)ljca_gpio->obuf;
+	int ret;
+
+	if (!ljca_gpio_valid(ljca_gpio, gpio_id))
+		return -EINVAL;
+
+	mutex_lock(&ljca_gpio->trans_lock);
+	packet->item[0].index = gpio_id;
+	packet->item[0].value = config | ljca_gpio->connect_mode[gpio_id];
+	packet->num = 1;
+
+	ret = ljca_transfer(ljca_gpio->pdev, GPIO_CONFIG, packet,
+			    GPIO_PAYLOAD_LEN(packet->num), NULL, NULL);
+	mutex_unlock(&ljca_gpio->trans_lock);
+	return ret;
+}
+
+static int ljca_gpio_read(struct ljca_gpio_dev *ljca_gpio, u8 gpio_id)
+{
+	struct gpio_packet *packet = (struct gpio_packet *)ljca_gpio->obuf;
+	struct gpio_packet *ack_packet;
+	int ret;
+	int ibuf_len;
+
+	if (!ljca_gpio_valid(ljca_gpio, gpio_id))
+		return -EINVAL;
+
+	mutex_lock(&ljca_gpio->trans_lock);
+	packet->num = 1;
+	packet->item[0].index = gpio_id;
+	ret = ljca_transfer(ljca_gpio->pdev, GPIO_READ, packet,
+			    GPIO_PAYLOAD_LEN(packet->num), ljca_gpio->ibuf,
+			    &ibuf_len);
+
+	ack_packet = (struct gpio_packet *)ljca_gpio->ibuf;
+	if (ret || !ibuf_len || ack_packet->num != packet->num) {
+		dev_err(&ljca_gpio->pdev->dev, "%s failed gpio_id:%d ret %d %d",
+			__func__, gpio_id, ret, ack_packet->num);
+		mutex_unlock(&ljca_gpio->trans_lock);
+		return -EIO;
+	}
+
+	mutex_unlock(&ljca_gpio->trans_lock);
+	return (ack_packet->item[0].value > 0) ? 1 : 0;
+}
+
+static int ljca_gpio_write(struct ljca_gpio_dev *ljca_gpio, u8 gpio_id,
+			   int value)
+{
+	struct gpio_packet *packet = (struct gpio_packet *)ljca_gpio->obuf;
+	int ret;
+
+	mutex_lock(&ljca_gpio->trans_lock);
+	packet->num = 1;
+	packet->item[0].index = gpio_id;
+	packet->item[0].value = (value & 1);
+
+	ret = ljca_transfer(ljca_gpio->pdev, GPIO_WRITE, packet,
+			    GPIO_PAYLOAD_LEN(packet->num), NULL, NULL);
+	mutex_unlock(&ljca_gpio->trans_lock);
+	return ret;
+}
+
+static int ljca_gpio_get_value(struct gpio_chip *chip, unsigned int offset)
+{
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(chip);
+
+	return ljca_gpio_read(ljca_gpio, offset);
+}
+
+static void ljca_gpio_set_value(struct gpio_chip *chip, unsigned int offset,
+				int val)
+{
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(chip);
+	int ret;
+
+	ret = ljca_gpio_write(ljca_gpio, offset, val);
+	if (ret)
+		dev_err(chip->parent,
+			"%s offset:%d val:%d set value failed %d\n", __func__,
+			offset, val, ret);
+}
+
+static int ljca_gpio_direction_input(struct gpio_chip *chip,
+				     unsigned int offset)
+{
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(chip);
+	u8 config = GPIO_CONF_INPUT | GPIO_CONF_CLR;
+
+	return gpio_config(ljca_gpio, offset, config);
+}
+
+static int ljca_gpio_direction_output(struct gpio_chip *chip,
+				      unsigned int offset, int val)
+{
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(chip);
+	u8 config = GPIO_CONF_OUTPUT | GPIO_CONF_CLR;
+	int ret;
+
+	ret = gpio_config(ljca_gpio, offset, config);
+	if (ret)
+		return ret;
+
+	ljca_gpio_set_value(chip, offset, val);
+	return 0;
+}
+
+static int ljca_gpio_set_config(struct gpio_chip *chip, unsigned int offset,
+				unsigned long config)
+{
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(chip);
+
+	if (!ljca_gpio_valid(ljca_gpio, offset))
+		return -EINVAL;
+
+	ljca_gpio->connect_mode[offset] = 0;
+	switch (pinconf_to_config_param(config)) {
+	case PIN_CONFIG_BIAS_PULL_UP:
+		ljca_gpio->connect_mode[offset] |= GPIO_CONF_PULLUP;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		ljca_gpio->connect_mode[offset] |= GPIO_CONF_PULLDOWN;
+		break;
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+	case PIN_CONFIG_PERSIST_STATE:
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
+static int ljca_enable_irq(struct ljca_gpio_dev *ljca_gpio, int gpio_id,
+			   bool enable)
+{
+	struct gpio_packet *packet = (struct gpio_packet *)ljca_gpio->obuf;
+	int ret;
+
+	mutex_lock(&ljca_gpio->trans_lock);
+	packet->num = 1;
+	packet->item[0].index = gpio_id;
+	packet->item[0].value = 0;
+
+	dev_dbg(ljca_gpio->gc.parent, "%s %d", __func__, gpio_id);
+
+	ret = ljca_transfer(ljca_gpio->pdev,
+			    enable == true ? GPIO_INT_UNMASK : GPIO_INT_MASK,
+			    packet, GPIO_PAYLOAD_LEN(packet->num), NULL, NULL);
+	mutex_unlock(&ljca_gpio->trans_lock);
+	return ret;
+}
+
+static void ljca_gpio_async(struct work_struct *work)
+{
+	struct ljca_gpio_dev *ljca_gpio =
+		container_of(work, struct ljca_gpio_dev, work);
+	int gpio_id;
+	int unmasked;
+
+	for_each_set_bit (gpio_id, ljca_gpio->reenable_irqs,
+			  ljca_gpio->gc.ngpio) {
+		clear_bit(gpio_id, ljca_gpio->reenable_irqs);
+		unmasked = test_bit(gpio_id, ljca_gpio->unmasked_irqs);
+		if (unmasked)
+			ljca_enable_irq(ljca_gpio, gpio_id, true);
+	}
+}
+
+void ljca_gpio_event_cb(struct platform_device *pdev, u8 cmd,
+			const void *evt_data, int len)
+{
+	const struct gpio_packet *packet = evt_data;
+	struct ljca_gpio_dev *ljca_gpio = platform_get_drvdata(pdev);
+	int i;
+	int irq;
+
+	if (cmd != GPIO_INT_EVENT)
+		return;
+
+	for (i = 0; i < packet->num; i++) {
+		irq = irq_find_mapping(ljca_gpio->gc.irq.domain,
+				       packet->item[i].index);
+		if (!irq) {
+			dev_err(ljca_gpio->gc.parent,
+				"gpio_id %d not mapped to IRQ\n",
+				packet->item[i].index);
+			return;
+		}
+
+		generic_handle_irq(irq);
+
+		set_bit(packet->item[i].index, ljca_gpio->reenable_irqs);
+		dev_dbg(ljca_gpio->gc.parent, "%s got one interrupt %d %d %d\n",
+			__func__, i, packet->item[i].index,
+			packet->item[i].value);
+	}
+
+	schedule_work(&ljca_gpio->work);
+}
+
+static void ljca_irq_unmask(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(gc);
+	int gpio_id = irqd_to_hwirq(irqd);
+
+	dev_dbg(ljca_gpio->gc.parent, "%s %d", __func__, gpio_id);
+	set_bit(gpio_id, ljca_gpio->unmasked_irqs);
+}
+
+static void ljca_irq_mask(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(gc);
+	int gpio_id = irqd_to_hwirq(irqd);
+
+	dev_dbg(ljca_gpio->gc.parent, "%s %d", __func__, gpio_id);
+	clear_bit(gpio_id, ljca_gpio->unmasked_irqs);
+}
+
+static int ljca_irq_set_type(struct irq_data *irqd, unsigned type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(gc);
+	int gpio_id = irqd_to_hwirq(irqd);
+
+	ljca_gpio->connect_mode[gpio_id] = GPIO_CONF_INTERRUPT;
+	switch (type) {
+	case IRQ_TYPE_LEVEL_HIGH:
+		ljca_gpio->connect_mode[gpio_id] |=
+			GPIO_CONF_LEVEL | GPIO_CONF_PULLUP;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		ljca_gpio->connect_mode[gpio_id] |=
+			GPIO_CONF_LEVEL | GPIO_CONF_PULLDOWN;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		ljca_gpio->connect_mode[gpio_id] |=
+			GPIO_CONF_EDGE | GPIO_CONF_PULLUP;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		ljca_gpio->connect_mode[gpio_id] |=
+			GPIO_CONF_EDGE | GPIO_CONF_PULLDOWN;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	dev_dbg(ljca_gpio->gc.parent, "%s %d %x\n", __func__, gpio_id,
+		ljca_gpio->connect_mode[gpio_id]);
+	return 0;
+}
+
+static void ljca_irq_bus_lock(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(gc);
+
+	mutex_lock(&ljca_gpio->irq_lock);
+}
+
+static void ljca_irq_bus_unlock(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct ljca_gpio_dev *ljca_gpio = gpiochip_get_data(gc);
+	int gpio_id = irqd_to_hwirq(irqd);
+	int enabled;
+	int unmasked;
+
+	enabled = test_bit(gpio_id, ljca_gpio->enabled_irqs);
+	unmasked = test_bit(gpio_id, ljca_gpio->unmasked_irqs);
+	dev_dbg(ljca_gpio->gc.parent, "%s %d %d %d\n", __func__, gpio_id,
+		 enabled, unmasked);
+
+	if (enabled != unmasked) {
+		if (unmasked) {
+			gpio_config(ljca_gpio, gpio_id, 0);
+			ljca_enable_irq(ljca_gpio, gpio_id, true);
+			set_bit(gpio_id, ljca_gpio->enabled_irqs);
+		} else {
+			ljca_enable_irq(ljca_gpio, gpio_id, false);
+			clear_bit(gpio_id, ljca_gpio->enabled_irqs);
+		}
+	}
+
+	mutex_unlock(&ljca_gpio->irq_lock);
+}
+
+static unsigned int ljca_irq_startup(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+
+	return gpiochip_lock_as_irq(gc, irqd_to_hwirq(irqd));
+}
+
+static void ljca_irq_shutdown(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+
+	gpiochip_unlock_as_irq(gc, irqd_to_hwirq(irqd));
+}
+
+static struct irq_chip ljca_gpio_irqchip = {
+	.name = "ljca-irq",
+	.irq_mask = ljca_irq_mask,
+	.irq_unmask = ljca_irq_unmask,
+	.irq_set_type = ljca_irq_set_type,
+	.irq_bus_lock = ljca_irq_bus_lock,
+	.irq_bus_sync_unlock = ljca_irq_bus_unlock,
+	.irq_startup = ljca_irq_startup,
+	.irq_shutdown = ljca_irq_shutdown,
+};
+
+static int ljca_gpio_probe(struct platform_device *pdev)
+{
+	struct ljca_gpio_dev *ljca_gpio;
+	struct ljca_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	struct gpio_irq_chip *girq;
+
+	ljca_gpio = devm_kzalloc(&pdev->dev, sizeof(*ljca_gpio), GFP_KERNEL);
+	if (!ljca_gpio)
+		return -ENOMEM;
+
+	ljca_gpio->ctr_info = &pdata->gpio_info;
+	ljca_gpio->connect_mode =
+		devm_kcalloc(&pdev->dev, ljca_gpio->ctr_info->num,
+			     sizeof(*ljca_gpio->connect_mode), GFP_KERNEL);
+	if (!ljca_gpio->connect_mode)
+		return -ENOMEM;
+
+	mutex_init(&ljca_gpio->irq_lock);
+	mutex_init(&ljca_gpio->trans_lock);
+	ljca_gpio->pdev = pdev;
+	ljca_gpio->gc.direction_input = ljca_gpio_direction_input;
+	ljca_gpio->gc.direction_output = ljca_gpio_direction_output;
+	ljca_gpio->gc.get = ljca_gpio_get_value;
+	ljca_gpio->gc.set = ljca_gpio_set_value;
+	ljca_gpio->gc.set_config = ljca_gpio_set_config;
+	ljca_gpio->gc.can_sleep = true;
+	ljca_gpio->gc.parent = &pdev->dev;
+
+	ljca_gpio->gc.base = -1;
+	ljca_gpio->gc.ngpio = ljca_gpio->ctr_info->num;
+	ljca_gpio->gc.label = "ljca-gpio";
+	ljca_gpio->gc.owner = THIS_MODULE;
+
+	platform_set_drvdata(pdev, ljca_gpio);
+	ljca_register_event_cb(pdev, ljca_gpio_event_cb);
+
+	girq = &ljca_gpio->gc.irq;
+	girq->chip = &ljca_gpio_irqchip;
+	girq->parent_handler = NULL;
+	girq->num_parents = 0;
+	girq->parents = NULL;
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_simple_irq;
+
+	INIT_WORK(&ljca_gpio->work, ljca_gpio_async);
+	return devm_gpiochip_add_data(&pdev->dev, &ljca_gpio->gc, ljca_gpio);
+}
+
+static int ljca_gpio_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver ljca_gpio_driver = {
+	.driver.name = "ljca-gpio",
+	.probe = ljca_gpio_probe,
+	.remove = ljca_gpio_remove,
+};
+
+module_platform_driver(ljca_gpio_driver);
+
+MODULE_AUTHOR("Ye Xiang <xiang.ye@intel.com>");
+MODULE_AUTHOR("Zhang Lixu <lixu.zhang@intel.com>");
+MODULE_DESCRIPTION("Intel La Jolla Cove Adapter USB-GPIO driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ljca-gpio");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-loongson1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-loongson1.c
@@ -25,10 +25,10 @@
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	__raw_writel(__raw_readl(gpio_reg_base + GPIO_CFG) | BIT(offset),
 		     gpio_reg_base + GPIO_CFG);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
@@ -37,10 +37,10 @@
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	__raw_writel(__raw_readl(gpio_reg_base + GPIO_CFG) & ~BIT(offset),
 		     gpio_reg_base + GPIO_CFG);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static int ls1x_gpio_probe(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-m058ssan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-m058ssan.c
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Driver for M058SSAN I2C GPO expander
+ *
+ * Copyright (C) 2023 Filippo Copetti <filippo.copetti@eurotech.com>
+ *
+ * Based on gpio-tpic2810.c
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ *	Andrew F. Davis <afd@ti.com>
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/property.h>
+
+/*
+ * GPIO bank #1 (offset 0...7) is configured as output
+ * GPIO bank #2 (offset 8...15) is configured as input
+ */
+
+#define M058SSAN_OUTPUT_BANK            0x01
+#define M058SSAN_INPUT_BANK             0x02
+#define M058SSAN_INPUT_OUTPUT_OFFSET    0x07
+
+/**
+ * m058ssan_read(gpio, &gpio->out, 0x02);
+ * o->out * struct m058ssan - GPIO driver data
+ * @chip: GPIO controller chip
+ * @lock: Protects write sequences
+ * @out: Buffer for device register
+ */
+struct m058ssan {
+	struct gpio_chip chip;
+	struct mutex lock;
+	u8 out;
+};
+
+static int m058ssan_read(struct m058ssan *gpio, u8 *value, u8 address)
+{
+	struct i2c_client *client = to_i2c_client(gpio->chip.parent);
+	int ret;
+
+	ret = i2c_smbus_read_byte_data(client, address);
+
+	if (ret < 0)
+		return ret;
+
+	*value = ret;
+
+	return 0;
+}
+
+static int m058ssan_write(struct m058ssan *gpio, u8 value, u8 address)
+{
+	struct i2c_client *client = to_i2c_client(gpio->chip.parent);
+
+	return i2c_smbus_write_byte_data(client, address, value);
+}
+
+static int m058ssan_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	if (offset > M058SSAN_INPUT_OUTPUT_OFFSET)
+		return GPIO_LINE_DIRECTION_IN;
+	else
+		return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int m058ssan_gpio_direction_input(struct gpio_chip *gc, unsigned int offset)
+{
+	if (offset > M058SSAN_INPUT_OUTPUT_OFFSET)
+		return 0;
+	else
+		return -1;
+}
+
+static int m058ssan_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	if (offset > M058SSAN_INPUT_OUTPUT_OFFSET)
+		return -1;
+	else
+		return 0;
+}
+
+static int m058ssan_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct m058ssan *gpio = gpiochip_get_data(chip);
+	u8 buffer;
+	int ret;
+
+	if (offset > M058SSAN_INPUT_OUTPUT_OFFSET) {
+		ret = m058ssan_read(gpio, &buffer, M058SSAN_INPUT_BANK);
+		offset -= (M058SSAN_INPUT_OUTPUT_OFFSET + 1);
+	} else {
+		ret = m058ssan_read(gpio, &buffer, M058SSAN_OUTPUT_BANK);
+	}
+	if (ret)
+		return ret;
+
+	return buffer & BIT(offset);
+}
+
+static void m058ssan_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+	struct m058ssan *gpio = gpiochip_get_data(chip);
+	u8 buffer;
+	int ret;
+
+	if (offset > M058SSAN_INPUT_OUTPUT_OFFSET)
+		return;
+
+	mutex_lock(&gpio->lock);
+
+	buffer = gpio->out;
+
+	if (value)
+		buffer |= BIT(offset);
+	else
+		buffer &= ~BIT(offset);
+
+	ret = m058ssan_write(gpio, buffer, M058SSAN_OUTPUT_BANK);
+
+	if (ret)
+		goto out;
+
+	gpio->out = buffer;
+
+out:
+	mutex_unlock(&gpio->lock);
+}
+
+static int m058ssan_probe(struct i2c_client *client)
+{
+	struct m058ssan *gpio;
+
+	gpio = devm_kzalloc(&client->dev, sizeof(*gpio), GFP_KERNEL);
+
+	if (!gpio)
+		return -ENOMEM;
+
+	gpio->chip.label = client->name;
+	gpio->chip.parent = &client->dev;
+	gpio->chip.owner = THIS_MODULE;
+	gpio->chip.get_direction = m058ssan_get_direction;
+	gpio->chip.direction_input = m058ssan_gpio_direction_input;
+	gpio->chip.direction_output = m058ssan_gpio_direction_output;
+	gpio->chip.get = m058ssan_get;
+	gpio->chip.set = m058ssan_set;
+	gpio->chip.base = -1;
+	gpio->chip.ngpio = 16;
+	gpio->chip.can_sleep = true;
+
+	mutex_init(&gpio->lock);
+
+	/* Read the current output level */
+	if (gpio->out > M058SSAN_INPUT_OUTPUT_OFFSET)
+		m058ssan_read(gpio, &gpio->out, M058SSAN_INPUT_BANK);
+	else
+		m058ssan_read(gpio, &gpio->out, M058SSAN_OUTPUT_BANK);
+
+	return devm_gpiochip_add_data(&client->dev, &gpio->chip, gpio);
+}
+
+static const struct i2c_device_id m058ssan_id_table[] = {
+	{"m058ssan", 4},
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(i2c, m058ssan_id_table);
+
+static const struct of_device_id m058ssan_of_match_table[] = {
+	{.compatible = "nuvoton,m058ssan", .data = (void *)4},
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, m058ssan_of_match_table);
+
+static struct i2c_driver m058ssan_driver = {
+	.driver = {
+		   .name = "m058ssan",
+		   .of_match_table = m058ssan_of_match_table,
+		   },
+	.probe_new = m058ssan_probe,
+	.id_table = m058ssan_id_table,
+};
+
+module_i2c_driver(m058ssan_driver);
+
+MODULE_AUTHOR("Filippo Copetti <filippo.copetti@eurotech.com>");
+MODULE_DESCRIPTION("GPIO expander driver for M058SSAN");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-menz127.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-menz127.c
@@ -64,7 +64,7 @@
 		debounce /= 50;
 	}
 
-	spin_lock(&gc->bgpio_lock);
+	raw_spin_lock(&gc->bgpio_lock);
 
 	db_en = readl(priv->reg_base + MEN_Z127_DBER);
 
@@ -79,7 +79,7 @@
 	writel(db_en, priv->reg_base + MEN_Z127_DBER);
 	writel(db_cnt, priv->reg_base + GPIO_TO_DBCNT_REG(gpio));
 
-	spin_unlock(&gc->bgpio_lock);
+	raw_spin_unlock(&gc->bgpio_lock);
 
 	return 0;
 }
@@ -91,7 +91,7 @@
 	struct men_z127_gpio *priv = gpiochip_get_data(gc);
 	u32 od_en;
 
-	spin_lock(&gc->bgpio_lock);
+	raw_spin_lock(&gc->bgpio_lock);
 	od_en = readl(priv->reg_base + MEN_Z127_ODER);
 
 	if (param == PIN_CONFIG_DRIVE_OPEN_DRAIN)
@@ -101,7 +101,7 @@
 		od_en &= ~BIT(offset);
 
 	writel(od_en, priv->reg_base + MEN_Z127_ODER);
-	spin_unlock(&gc->bgpio_lock);
+	raw_spin_unlock(&gc->bgpio_lock);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-mlxbf2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-mlxbf2.c
@@ -120,7 +120,7 @@
 	u32 arm_gpio_lock_val;
 
 	mutex_lock(yu_arm_gpio_lock_param.lock);
-	spin_lock(&gs->gc.bgpio_lock);
+	raw_spin_lock(&gs->gc.bgpio_lock);
 
 	arm_gpio_lock_val = readl(yu_arm_gpio_lock_param.io);
 
@@ -128,7 +128,7 @@
 	 * When lock active bit[31] is set, ModeX is write enabled
 	 */
 	if (YU_LOCK_ACTIVE_BIT(arm_gpio_lock_val)) {
-		spin_unlock(&gs->gc.bgpio_lock);
+		raw_spin_unlock(&gs->gc.bgpio_lock);
 		mutex_unlock(yu_arm_gpio_lock_param.lock);
 		return -EINVAL;
 	}
@@ -146,7 +146,7 @@
 	__releases(yu_arm_gpio_lock_param.lock)
 {
 	writel(YU_ARM_GPIO_LOCK_RELEASE, yu_arm_gpio_lock_param.io);
-	spin_unlock(&gs->gc.bgpio_lock);
+	raw_spin_unlock(&gs->gc.bgpio_lock);
 	mutex_unlock(yu_arm_gpio_lock_param.lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-mmio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-mmio.c
@@ -220,7 +220,7 @@
 	unsigned long mask = bgpio_line2mask(gc, gpio);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	if (val)
 		gc->bgpio_data |= mask;
@@ -229,7 +229,7 @@
 
 	gc->write_reg(gc->reg_dat, gc->bgpio_data);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void bgpio_set_with_clear(struct gpio_chip *gc, unsigned int gpio,
@@ -248,7 +248,7 @@
 	unsigned long mask = bgpio_line2mask(gc, gpio);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	if (val)
 		gc->bgpio_data |= mask;
@@ -257,7 +257,7 @@
 
 	gc->write_reg(gc->reg_set, gc->bgpio_data);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void bgpio_multiple_get_masks(struct gpio_chip *gc,
@@ -286,7 +286,7 @@
 	unsigned long flags;
 	unsigned long set_mask, clear_mask;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	bgpio_multiple_get_masks(gc, mask, bits, &set_mask, &clear_mask);
 
@@ -295,7 +295,7 @@
 
 	gc->write_reg(reg, gc->bgpio_data);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void bgpio_set_multiple(struct gpio_chip *gc, unsigned long *mask,
@@ -347,7 +347,7 @@
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	gc->bgpio_dir &= ~bgpio_line2mask(gc, gpio);
 
@@ -356,7 +356,7 @@
 	if (gc->reg_dir_out)
 		gc->write_reg(gc->reg_dir_out, gc->bgpio_dir);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
@@ -387,7 +387,7 @@
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	gc->bgpio_dir |= bgpio_line2mask(gc, gpio);
 
@@ -396,7 +396,7 @@
 	if (gc->reg_dir_out)
 		gc->write_reg(gc->reg_dir_out, gc->bgpio_dir);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static int bgpio_dir_out_dir_first(struct gpio_chip *gc, unsigned int gpio,
@@ -610,7 +610,7 @@
 	if (gc->bgpio_bits > BITS_PER_LONG)
 		return -EINVAL;
 
-	spin_lock_init(&gc->bgpio_lock);
+	raw_spin_lock_init(&gc->bgpio_lock);
 	gc->parent = dev;
 	gc->label = dev_name(dev);
 	gc->base = -1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-mockup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-mockup.c
@@ -368,11 +368,18 @@
 		priv->offset = i;
 		priv->desc = gpiochip_get_desc(gc, i);
 
-		debugfs_create_file(name, 0200, chip->dbg_dir, priv,
+		debugfs_create_file(name, 0600, chip->dbg_dir, priv,
 				    &gpio_mockup_debugfs_ops);
 	}
 }
 
+static void gpio_mockup_debugfs_cleanup(void *data)
+{
+	struct gpio_mockup_chip *chip = data;
+
+	debugfs_remove_recursive(chip->dbg_dir);
+}
+
 static void gpio_mockup_dispose_mappings(void *data)
 {
 	struct gpio_mockup_chip *chip = data;
@@ -455,7 +462,7 @@
 
 	gpio_mockup_debugfs_setup(dev, chip);
 
-	return 0;
+	return devm_add_action_or_reset(dev, gpio_mockup_debugfs_cleanup, chip);
 }
 
 static const struct of_device_id gpio_mockup_of_match[] = {
@@ -547,8 +554,10 @@
 	}
 
 	fwnode = fwnode_create_software_node(properties, NULL);
-	if (IS_ERR(fwnode))
+	if (IS_ERR(fwnode)) {
+		kfree_strarray(line_names, ngpio);
 		return PTR_ERR(fwnode);
+	}
 
 	pdevinfo.name = "gpio-mockup";
 	pdevinfo.id = idx;
@@ -611,9 +620,9 @@
 
 static void __exit gpio_mockup_exit(void)
 {
+	gpio_mockup_unregister_pdevs();
 	debugfs_remove_recursive(gpio_mockup_dbg_dir);
 	platform_driver_unregister(&gpio_mockup_driver);
-	gpio_mockup_unregister_pdevs();
 }
 
 module_init(gpio_mockup_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-mpc8xxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-mpc8xxx.c
@@ -47,7 +47,7 @@
 				unsigned offset, int value);
 
 	struct irq_domain *irq;
-	unsigned int irqn;
+	int irqn;
 };
 
 /*
@@ -172,6 +172,7 @@
 
 	switch (flow_type) {
 	case IRQ_TYPE_EDGE_FALLING:
+	case IRQ_TYPE_LEVEL_LOW:
 		raw_spin_lock_irqsave(&mpc8xxx_gc->lock, flags);
 		gc->write_reg(mpc8xxx_gc->regs + GPIO_ICR,
 			gc->read_reg(mpc8xxx_gc->regs + GPIO_ICR)
@@ -388,8 +389,8 @@
 	}
 
 	mpc8xxx_gc->irqn = platform_get_irq(pdev, 0);
-	if (!mpc8xxx_gc->irqn)
-		return 0;
+	if (mpc8xxx_gc->irqn < 0)
+		return mpc8xxx_gc->irqn;
 
 	mpc8xxx_gc->irq = irq_domain_create_linear(fwnode,
 						   MPC8XXX_GPIO_PINS,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-mvebu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-mvebu.c
@@ -707,6 +707,9 @@
 	unsigned long flags;
 	unsigned int on, off;
 
+	if (state->polarity != PWM_POLARITY_NORMAL)
+		return -EINVAL;
+
 	val = (unsigned long long) mvpwm->clk_rate * state->duty_cycle;
 	do_div(val, NSEC_PER_SEC);
 	if (val > UINT_MAX + 1ULL)
@@ -790,8 +793,12 @@
 	u32 offset;
 	u32 set;
 
-	if (of_device_is_compatible(mvchip->chip.of_node,
-				    "marvell,armada-370-gpio")) {
+	if (mvchip->soc_variant == MVEBU_GPIO_SOC_VARIANT_A8K) {
+		int ret = of_property_read_u32(dev->of_node,
+					       "marvell,pwm-offset", &offset);
+		if (ret < 0)
+			return 0;
+	} else {
 		/*
 		 * There are only two sets of PWM configuration registers for
 		 * all the GPIO lines on those SoCs which this driver reserves
@@ -801,13 +808,6 @@
 		if (!platform_get_resource_byname(pdev, IORESOURCE_MEM, "pwm"))
 			return 0;
 		offset = 0;
-	} else if (mvchip->soc_variant == MVEBU_GPIO_SOC_VARIANT_A8K) {
-		int ret = of_property_read_u32(dev->of_node,
-					       "marvell,pwm-offset", &offset);
-		if (ret < 0)
-			return 0;
-	} else {
-		return 0;
 	}
 
 	if (IS_ERR(mvchip->clk))
@@ -871,17 +871,10 @@
 	mvpwm->chip.dev = dev;
 	mvpwm->chip.ops = &mvebu_pwm_ops;
 	mvpwm->chip.npwm = mvchip->chip.ngpio;
-	/*
-	 * There may already be some PWM allocated, so we can't force
-	 * mvpwm->chip.base to a fixed point like mvchip->chip.base.
-	 * So, we let pwmchip_add() do the numbering and take the next free
-	 * region.
-	 */
-	mvpwm->chip.base = -1;
 
 	spin_lock_init(&mvpwm->lock);
 
-	return pwmchip_add(&mvpwm->chip);
+	return devm_pwmchip_add(dev, &mvpwm->chip);
 }
 
 #ifdef CONFIG_DEBUG_FS
@@ -1119,6 +1112,13 @@
 	return 0;
 }
 
+static void mvebu_gpio_remove_irq_domain(void *data)
+{
+	struct irq_domain *domain = data;
+
+	irq_domain_remove(domain);
+}
+
 static int mvebu_gpio_probe(struct platform_device *pdev)
 {
 	struct mvebu_gpio_chip *mvchip;
@@ -1251,17 +1251,21 @@
 	if (!mvchip->domain) {
 		dev_err(&pdev->dev, "couldn't allocate irq domain %s (DT).\n",
 			mvchip->chip.label);
-		err = -ENODEV;
-		goto err_pwm;
+		return -ENODEV;
 	}
 
+	err = devm_add_action_or_reset(&pdev->dev, mvebu_gpio_remove_irq_domain,
+				       mvchip->domain);
+	if (err)
+		return err;
+
 	err = irq_alloc_domain_generic_chips(
 	    mvchip->domain, ngpios, 2, np->name, handle_level_irq,
 	    IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_LEVEL, 0, 0);
 	if (err) {
 		dev_err(&pdev->dev, "couldn't allocate irq chips %s (DT).\n",
 			mvchip->chip.label);
-		goto err_domain;
+		return err;
 	}
 
 	/*
@@ -1301,13 +1305,6 @@
 	}
 
 	return 0;
-
-err_domain:
-	irq_domain_remove(mvchip->domain);
-err_pwm:
-	pwmchip_remove(&mvchip->mvpwm->chip);
-
-	return err;
 }
 
 static struct platform_driver mvebu_gpio_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-mxc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-mxc.c
@@ -18,6 +18,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 #include <linux/syscore_ops.h>
 #include <linux/gpio/driver.h>
 #include <linux/of.h>
@@ -147,6 +148,7 @@
 {
 	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
 	struct mxc_gpio_port *port = gc->private;
+	unsigned long flags;
 	u32 bit, val;
 	u32 gpio_idx = d->hwirq;
 	int edge;
@@ -185,6 +187,8 @@
 		return -EINVAL;
 	}
 
+	raw_spin_lock_irqsave(&port->gc.bgpio_lock, flags);
+
 	if (GPIO_EDGE_SEL >= 0) {
 		val = readl(port->base + GPIO_EDGE_SEL);
 		if (edge == GPIO_INT_BOTH_EDGES)
@@ -204,15 +208,20 @@
 
 	writel(1 << gpio_idx, port->base + GPIO_ISR);
 
-	return 0;
+	raw_spin_unlock_irqrestore(&port->gc.bgpio_lock, flags);
+
+	return port->gc.direction_input(&port->gc, gpio_idx);
 }
 
 static void mxc_flip_edge(struct mxc_gpio_port *port, u32 gpio)
 {
 	void __iomem *reg = port->base;
+	unsigned long flags;
 	u32 bit, val;
 	int edge;
 
+	raw_spin_lock_irqsave(&port->gc.bgpio_lock, flags);
+
 	reg += GPIO_ICR1 + ((gpio & 0x10) >> 2); /* lower or upper register */
 	bit = gpio & 0xf;
 	val = readl(reg);
@@ -227,9 +236,12 @@
 	} else {
 		pr_err("mxc: invalid configuration for GPIO %d: %x\n",
 		       gpio, edge);
-		return;
+		goto unlock;
 	}
 	writel(val | (edge << (bit << 1)), reg);
+
+unlock:
+	raw_spin_unlock_irqrestore(&port->gc.bgpio_lock, flags);
 }
 
 /* handle 32 interrupts in one status register */
@@ -433,8 +445,7 @@
 	port->gc.request = gpiochip_generic_request;
 	port->gc.free = gpiochip_generic_free;
 	port->gc.to_irq = mxc_gpio_to_irq;
-	port->gc.base = (pdev->id < 0) ? of_alias_get_id(np, "gpio") * 32 :
-					     pdev->id * 32;
+	port->gc.base = of_alias_get_id(np, "gpio") * 32;
 
 	err = devm_gpiochip_add_data(&pdev->dev, &port->gc, port);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-pca953x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-pca953x.c
@@ -351,6 +351,9 @@
 	.reg_bits = 8,
 	.val_bits = 8,
 
+	.use_single_read = true,
+	.use_single_write = true,
+
 	.readable_reg = pca953x_readable_register,
 	.writeable_reg = pca953x_writeable_register,
 	.volatile_reg = pca953x_volatile_register,
@@ -730,25 +733,6 @@
 	DECLARE_BITMAP(trigger, MAX_LINE);
 	int ret;
 
-	if (chip->driver_data & PCA_PCAL) {
-		/* Read the current interrupt status from the device */
-		ret = pca953x_read_regs(chip, PCAL953X_INT_STAT, trigger);
-		if (ret)
-			return false;
-
-		/* Check latched inputs and clear interrupt status */
-		ret = pca953x_read_regs(chip, chip->regs->input, cur_stat);
-		if (ret)
-			return false;
-
-		/* Apply filter for rising/falling edge selection */
-		bitmap_replace(new_stat, chip->irq_trig_fall, chip->irq_trig_raise, cur_stat, gc->ngpio);
-
-		bitmap_and(pending, new_stat, trigger, gc->ngpio);
-
-		return !bitmap_empty(pending, gc->ngpio);
-	}
-
 	ret = pca953x_read_regs(chip, chip->regs->input, cur_stat);
 	if (ret)
 		return false;
@@ -762,11 +746,11 @@
 	bitmap_xor(cur_stat, new_stat, old_stat, gc->ngpio);
 	bitmap_and(trigger, cur_stat, chip->irq_mask, gc->ngpio);
 
+	bitmap_copy(chip->irq_stat, new_stat, gc->ngpio);
+
 	if (bitmap_empty(trigger, gc->ngpio))
 		return false;
 
-	bitmap_copy(chip->irq_stat, new_stat, gc->ngpio);
-
 	bitmap_and(cur_stat, chip->irq_trig_fall, old_stat, gc->ngpio);
 	bitmap_and(old_stat, chip->irq_trig_raise, new_stat, gc->ngpio);
 	bitmap_or(new_stat, old_stat, cur_stat, gc->ngpio);
@@ -894,15 +878,18 @@
 static int device_pca95xx_init(struct pca953x_chip *chip, u32 invert)
 {
 	DECLARE_BITMAP(val, MAX_LINE);
+	u8 regaddr;
 	int ret;
 
-	ret = regcache_sync_region(chip->regmap, chip->regs->output,
-				   chip->regs->output + NBANK(chip));
+	regaddr = pca953x_recalc_addr(chip, chip->regs->output, 0);
+	ret = regcache_sync_region(chip->regmap, regaddr,
+				   regaddr + NBANK(chip) - 1);
 	if (ret)
 		goto out;
 
-	ret = regcache_sync_region(chip->regmap, chip->regs->direction,
-				   chip->regs->direction + NBANK(chip));
+	regaddr = pca953x_recalc_addr(chip, chip->regs->direction, 0);
+	ret = regcache_sync_region(chip->regmap, regaddr,
+				   regaddr + NBANK(chip) - 1);
 	if (ret)
 		goto out;
 
@@ -1108,20 +1095,21 @@
 {
 	struct pca953x_chip *chip = dev_get_drvdata(dev);
 	int ret;
+	u8 regaddr;
 
 	/*
 	 * The ordering between direction and output is important,
 	 * sync these registers first and only then sync the rest.
 	 */
-	ret = regcache_sync_region(chip->regmap, chip->regs->direction,
-				   chip->regs->direction + NBANK(chip));
+	regaddr = pca953x_recalc_addr(chip, chip->regs->direction, 0);
+	ret = regcache_sync_region(chip->regmap, regaddr, regaddr + NBANK(chip) - 1);
 	if (ret) {
 		dev_err(dev, "Failed to sync GPIO dir registers: %d\n", ret);
 		return ret;
 	}
 
-	ret = regcache_sync_region(chip->regmap, chip->regs->output,
-				   chip->regs->output + NBANK(chip));
+	regaddr = pca953x_recalc_addr(chip, chip->regs->output, 0);
+	ret = regcache_sync_region(chip->regmap, regaddr, regaddr + NBANK(chip) - 1);
 	if (ret) {
 		dev_err(dev, "Failed to sync GPIO out registers: %d\n", ret);
 		return ret;
@@ -1129,16 +1117,18 @@
 
 #ifdef CONFIG_GPIO_PCA953X_IRQ
 	if (chip->driver_data & PCA_PCAL) {
-		ret = regcache_sync_region(chip->regmap, PCAL953X_IN_LATCH,
-					   PCAL953X_IN_LATCH + NBANK(chip));
+		regaddr = pca953x_recalc_addr(chip, PCAL953X_IN_LATCH, 0);
+		ret = regcache_sync_region(chip->regmap, regaddr,
+					   regaddr + NBANK(chip) - 1);
 		if (ret) {
 			dev_err(dev, "Failed to sync INT latch registers: %d\n",
 				ret);
 			return ret;
 		}
 
-		ret = regcache_sync_region(chip->regmap, PCAL953X_INT_MASK,
-					   PCAL953X_INT_MASK + NBANK(chip));
+		regaddr = pca953x_recalc_addr(chip, PCAL953X_INT_MASK, 0);
+		ret = regcache_sync_region(chip->regmap, regaddr,
+					   regaddr + NBANK(chip) - 1);
 		if (ret) {
 			dev_err(dev, "Failed to sync INT mask registers: %d\n",
 				ret);
@@ -1154,7 +1144,9 @@
 {
 	struct pca953x_chip *chip = dev_get_drvdata(dev);
 
+	mutex_lock(&chip->i2c_lock);
 	regcache_cache_only(chip->regmap, true);
+	mutex_unlock(&chip->i2c_lock);
 
 	if (atomic_read(&chip->wakeup_path))
 		device_set_wakeup_path(dev);
@@ -1177,13 +1169,17 @@
 		}
 	}
 
+	mutex_lock(&chip->i2c_lock);
 	regcache_cache_only(chip->regmap, false);
 	regcache_mark_dirty(chip->regmap);
 	ret = pca953x_regcache_sync(dev);
-	if (ret)
+	if (ret) {
+		mutex_unlock(&chip->i2c_lock);
 		return ret;
+	}
 
 	ret = regcache_sync(chip->regmap);
+	mutex_unlock(&chip->i2c_lock);
 	if (ret) {
 		dev_err(dev, "Failed to restore register map: %d\n", ret);
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-pmic-eic-sprd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-pmic-eic-sprd.c
@@ -338,6 +338,7 @@
 	pmic_eic->chip.set_config = sprd_pmic_eic_set_config;
 	pmic_eic->chip.set = sprd_pmic_eic_set;
 	pmic_eic->chip.get = sprd_pmic_eic_get;
+	pmic_eic->chip.can_sleep = true;
 
 	pmic_eic->intc.name = dev_name(&pdev->dev);
 	pmic_eic->intc.irq_mask = sprd_pmic_eic_irq_mask;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-pxa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-pxa.c
@@ -243,6 +243,7 @@
 	switch (gpio_type) {
 	case PXA3XX_GPIO:
 	case MMP2_GPIO:
+	case MMP_GPIO:
 		return false;
 
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-rcar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-rcar.c
@@ -41,7 +41,7 @@
 
 struct gpio_rcar_priv {
 	void __iomem *base;
-	spinlock_t lock;
+	raw_spinlock_t lock;
 	struct device *dev;
 	struct gpio_chip gpio_chip;
 	struct irq_chip irq_chip;
@@ -121,7 +121,7 @@
 	 * "Setting Level-Sensitive Interrupt Input Mode"
 	 */
 
-	spin_lock_irqsave(&p->lock, flags);
+	raw_spin_lock_irqsave(&p->lock, flags);
 
 	/* Configure positive or negative logic in POSNEG */
 	gpio_rcar_modify_bit(p, POSNEG, hwirq, !active_high_rising_edge);
@@ -140,7 +140,7 @@
 	if (!level_trigger)
 		gpio_rcar_write(p, INTCLR, BIT(hwirq));
 
-	spin_unlock_irqrestore(&p->lock, flags);
+	raw_spin_unlock_irqrestore(&p->lock, flags);
 }
 
 static int gpio_rcar_irq_set_type(struct irq_data *d, unsigned int type)
@@ -233,7 +233,7 @@
 	 * "Setting General Input Mode"
 	 */
 
-	spin_lock_irqsave(&p->lock, flags);
+	raw_spin_lock_irqsave(&p->lock, flags);
 
 	/* Configure positive logic in POSNEG */
 	gpio_rcar_modify_bit(p, POSNEG, gpio, false);
@@ -248,7 +248,7 @@
 	if (p->info.has_outdtsel && output)
 		gpio_rcar_modify_bit(p, OUTDTSEL, gpio, false);
 
-	spin_unlock_irqrestore(&p->lock, flags);
+	raw_spin_unlock_irqrestore(&p->lock, flags);
 }
 
 static int gpio_rcar_request(struct gpio_chip *chip, unsigned offset)
@@ -334,7 +334,7 @@
 		return 0;
 	}
 
-	spin_lock_irqsave(&p->lock, flags);
+	raw_spin_lock_irqsave(&p->lock, flags);
 	outputs = gpio_rcar_read(p, INOUTSEL);
 	m = outputs & bankmask;
 	if (m)
@@ -343,7 +343,7 @@
 	m = ~outputs & bankmask;
 	if (m)
 		val |= gpio_rcar_read(p, INDT) & m;
-	spin_unlock_irqrestore(&p->lock, flags);
+	raw_spin_unlock_irqrestore(&p->lock, flags);
 
 	bits[0] = val;
 	return 0;
@@ -354,9 +354,9 @@
 	struct gpio_rcar_priv *p = gpiochip_get_data(chip);
 	unsigned long flags;
 
-	spin_lock_irqsave(&p->lock, flags);
+	raw_spin_lock_irqsave(&p->lock, flags);
 	gpio_rcar_modify_bit(p, OUTDT, offset, value);
-	spin_unlock_irqrestore(&p->lock, flags);
+	raw_spin_unlock_irqrestore(&p->lock, flags);
 }
 
 static void gpio_rcar_set_multiple(struct gpio_chip *chip, unsigned long *mask,
@@ -373,12 +373,12 @@
 	if (!bankmask)
 		return;
 
-	spin_lock_irqsave(&p->lock, flags);
+	raw_spin_lock_irqsave(&p->lock, flags);
 	val = gpio_rcar_read(p, OUTDT);
 	val &= ~bankmask;
 	val |= (bankmask & bits[0]);
 	gpio_rcar_write(p, OUTDT, val);
-	spin_unlock_irqrestore(&p->lock, flags);
+	raw_spin_unlock_irqrestore(&p->lock, flags);
 }
 
 static int gpio_rcar_direction_output(struct gpio_chip *chip, unsigned offset,
@@ -452,7 +452,12 @@
 	p->info = *info;
 
 	ret = of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3, 0, &args);
-	*npins = ret == 0 ? args.args[2] : RCAR_MAX_GPIO_PER_BANK;
+	if (ret) {
+		*npins = RCAR_MAX_GPIO_PER_BANK;
+	} else {
+		*npins = args.args[2];
+		of_node_put(args.np);
+	}
 
 	if (*npins == 0 || *npins > RCAR_MAX_GPIO_PER_BANK) {
 		dev_warn(p->dev, "Invalid number of gpio lines %u, using %u\n",
@@ -491,7 +496,7 @@
 		return -ENOMEM;
 
 	p->dev = dev;
-	spin_lock_init(&p->lock);
+	raw_spin_lock_init(&p->lock);
 
 	/* Get device configuration from DT node */
 	ret = gpio_rcar_parse_dt(p, &npins);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-realtek-otto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-realtek-otto.c
@@ -205,7 +205,7 @@
 		status = realtek_gpio_read_isr(ctrl, lines_done / 8);
 		port_pin_count = min(gc->ngpio - lines_done, 8U);
 		for_each_set_bit(offset, &status, port_pin_count)
-			generic_handle_domain_irq(gc->irq.domain, offset);
+			generic_handle_domain_irq(gc->irq.domain, offset + lines_done);
 	}
 
 	chained_irq_exit(irq_chip, desc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-rockchip.c
@@ -19,6 +19,8 @@
 #include <linux/of_address.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinconf-generic.h>
 #include <linux/regmap.h>
 
 #include "../pinctrl/core.h"
@@ -154,6 +156,12 @@
 	unsigned long flags;
 	u32 data = input ? 0 : 1;
 
+
+	if (input)
+		pinctrl_gpio_direction_input(bank->pin_base + offset);
+	else
+		pinctrl_gpio_direction_output(bank->pin_base + offset);
+
 	raw_spin_lock_irqsave(&bank->slock, flags);
 	rockchip_gpio_writel_bit(bank, offset, data, bank->gpio_regs->port_ddr);
 	raw_spin_unlock_irqrestore(&bank->slock, flags);
@@ -410,20 +418,18 @@
 	level = rockchip_gpio_readl(bank, bank->gpio_regs->int_type);
 	polarity = rockchip_gpio_readl(bank, bank->gpio_regs->int_polarity);
 
-	switch (type) {
-	case IRQ_TYPE_EDGE_BOTH:
+	if (type == IRQ_TYPE_EDGE_BOTH) {
 		if (bank->gpio_type == GPIO_TYPE_V2) {
-			bank->toggle_edge_mode &= ~mask;
 			rockchip_gpio_writel_bit(bank, d->hwirq, 1,
 						 bank->gpio_regs->int_bothedge);
 			goto out;
 		} else {
 			bank->toggle_edge_mode |= mask;
-			level |= mask;
+			level &= ~mask;
 
 			/*
 			 * Determine gpio state. If 1 next interrupt should be
-			 * falling otherwise rising.
+			 * low otherwise high.
 			 */
 			data = readl(bank->reg_base + bank->gpio_regs->ext_port);
 			if (data & mask)
@@ -431,30 +437,34 @@
 			else
 				polarity |= mask;
 		}
-		break;
-	case IRQ_TYPE_EDGE_RISING:
-		bank->toggle_edge_mode &= ~mask;
-		level |= mask;
-		polarity |= mask;
-		break;
-	case IRQ_TYPE_EDGE_FALLING:
-		bank->toggle_edge_mode &= ~mask;
-		level |= mask;
-		polarity &= ~mask;
-		break;
-	case IRQ_TYPE_LEVEL_HIGH:
-		bank->toggle_edge_mode &= ~mask;
-		level &= ~mask;
-		polarity |= mask;
-		break;
-	case IRQ_TYPE_LEVEL_LOW:
-		bank->toggle_edge_mode &= ~mask;
-		level &= ~mask;
-		polarity &= ~mask;
-		break;
-	default:
-		ret = -EINVAL;
-		goto out;
+	} else {
+		if (bank->gpio_type == GPIO_TYPE_V2) {
+			rockchip_gpio_writel_bit(bank, d->hwirq, 0,
+						 bank->gpio_regs->int_bothedge);
+		} else {
+			bank->toggle_edge_mode &= ~mask;
+		}
+		switch (type) {
+		case IRQ_TYPE_EDGE_RISING:
+			level |= mask;
+			polarity |= mask;
+			break;
+		case IRQ_TYPE_EDGE_FALLING:
+			level |= mask;
+			polarity &= ~mask;
+			break;
+		case IRQ_TYPE_LEVEL_HIGH:
+			level &= ~mask;
+			polarity |= mask;
+			break;
+		case IRQ_TYPE_LEVEL_LOW:
+			level &= ~mask;
+			polarity &= ~mask;
+			break;
+		default:
+			ret = -EINVAL;
+			goto out;
+		}
 	}
 
 	rockchip_gpio_writel(bank, level, bank->gpio_regs->int_type);
@@ -595,6 +605,7 @@
 			return -ENODATA;
 
 		pctldev = of_pinctrl_get(pctlnp);
+		of_node_put(pctlnp);
 		if (!pctldev)
 			return -ENODEV;
 
@@ -689,7 +700,7 @@
 	struct device_node *pctlnp = of_get_parent(np);
 	struct pinctrl_dev *pctldev = NULL;
 	struct rockchip_pin_bank *bank = NULL;
-	struct rockchip_pin_output_deferred *cfg;
+	struct rockchip_pin_deferred *cfg;
 	static int gpio;
 	int id, ret;
 
@@ -697,6 +708,7 @@
 		return -ENODEV;
 
 	pctldev = of_pinctrl_get(pctlnp);
+	of_node_put(pctlnp);
 	if (!pctldev)
 		return -EPROBE_DEFER;
 
@@ -730,15 +742,22 @@
 		return ret;
 	}
 
-	while (!list_empty(&bank->deferred_output)) {
-		cfg = list_first_entry(&bank->deferred_output,
-				       struct rockchip_pin_output_deferred, head);
+	while (!list_empty(&bank->deferred_pins)) {
+		cfg = list_first_entry(&bank->deferred_pins,
+				       struct rockchip_pin_deferred, head);
 		list_del(&cfg->head);
 
-		ret = rockchip_gpio_direction_output(&bank->gpio_chip, cfg->pin, cfg->arg);
-		if (ret)
-			dev_warn(dev, "setting output pin %u to %u failed\n", cfg->pin, cfg->arg);
-
+		switch (cfg->param) {
+		case PIN_CONFIG_OUTPUT:
+			ret = rockchip_gpio_direction_output(&bank->gpio_chip, cfg->pin, cfg->arg);
+			if (ret)
+				dev_warn(dev, "setting output pin %u to %u failed\n", cfg->pin,
+					 cfg->arg);
+			break;
+		default:
+			dev_warn(dev, "unknown deferred config param %d\n", cfg->param);
+			break;
+		}
 		kfree(cfg);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-sifive.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-sifive.c
@@ -44,7 +44,7 @@
 	unsigned long flags;
 	unsigned int trigger;
 
-	spin_lock_irqsave(&chip->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gc.bgpio_lock, flags);
 	trigger = (chip->irq_state & BIT(offset)) ? chip->trigger[offset] : 0;
 	regmap_update_bits(chip->regs, SIFIVE_GPIO_RISE_IE, BIT(offset),
 			   (trigger & IRQ_TYPE_EDGE_RISING) ? BIT(offset) : 0);
@@ -54,7 +54,7 @@
 			   (trigger & IRQ_TYPE_LEVEL_HIGH) ? BIT(offset) : 0);
 	regmap_update_bits(chip->regs, SIFIVE_GPIO_LOW_IE, BIT(offset),
 			   (trigger & IRQ_TYPE_LEVEL_LOW) ? BIT(offset) : 0);
-	spin_unlock_irqrestore(&chip->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gc.bgpio_lock, flags);
 }
 
 static int sifive_gpio_irq_set_type(struct irq_data *d, unsigned int trigger)
@@ -84,13 +84,13 @@
 	/* Switch to input */
 	gc->direction_input(gc, offset);
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	/* Clear any sticky pending interrupts */
 	regmap_write(chip->regs, SIFIVE_GPIO_RISE_IP, bit);
 	regmap_write(chip->regs, SIFIVE_GPIO_FALL_IP, bit);
 	regmap_write(chip->regs, SIFIVE_GPIO_HIGH_IP, bit);
 	regmap_write(chip->regs, SIFIVE_GPIO_LOW_IP, bit);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	/* Enable interrupts */
 	assign_bit(offset, &chip->irq_state, 1);
@@ -116,13 +116,13 @@
 	u32 bit = BIT(offset);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 	/* Clear all pending interrupts */
 	regmap_write(chip->regs, SIFIVE_GPIO_RISE_IP, bit);
 	regmap_write(chip->regs, SIFIVE_GPIO_FALL_IP, bit);
 	regmap_write(chip->regs, SIFIVE_GPIO_HIGH_IP, bit);
 	regmap_write(chip->regs, SIFIVE_GPIO_LOW_IP, bit);
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	irq_chip_eoi_parent(d);
 }
@@ -209,13 +209,18 @@
 		return -ENODEV;
 	}
 	parent = irq_find_host(irq_parent);
+	of_node_put(irq_parent);
 	if (!parent) {
 		dev_err(dev, "no IRQ parent domain\n");
 		return -ENODEV;
 	}
 
-	for (i = 0; i < ngpio; i++)
-		chip->irq_number[i] = platform_get_irq(pdev, i);
+	for (i = 0; i < ngpio; i++) {
+		ret = platform_get_irq(pdev, i);
+		if (ret < 0)
+			return ret;
+		chip->irq_number[i] = ret;
+	}
 
 	ret = bgpio_init(&chip->gc, dev, 4,
 			 chip->base + SIFIVE_GPIO_INPUT_VAL,
@@ -223,7 +228,7 @@
 			 NULL,
 			 chip->base + SIFIVE_GPIO_OUTPUT_EN,
 			 chip->base + SIFIVE_GPIO_INPUT_EN,
-			 0);
+			 BGPIOF_READ_OUTPUT_REG_SET);
 	if (ret) {
 		dev_err(dev, "unable to init generic GPIO\n");
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-slg7xl45106.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-slg7xl45106.c
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Driver for slg7xl45106 I2C GPO expander
+ * Based on gpio-pca9570.c
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/property.h>
+
+#define SLG7XL45106_GPO_REG	0xDB
+
+/**
+ * struct slg7xl45106 - GPIO driver data
+ * @chip: GPIO controller chip
+ * @lock: Protects write sequences
+ */
+struct slg7xl45106 {
+	struct gpio_chip chip;
+	struct mutex lock;	/* To protect writes */
+};
+
+static int slg7xl45106_read(struct slg7xl45106 *gpio)
+{
+	struct i2c_client *client = to_i2c_client(gpio->chip.parent);
+
+	return i2c_smbus_read_byte_data(client, SLG7XL45106_GPO_REG);
+}
+
+static int slg7xl45106_write(struct slg7xl45106 *gpio, u8 value)
+{
+	struct i2c_client *client = to_i2c_client(gpio->chip.parent);
+
+	return i2c_smbus_write_byte_data(client, SLG7XL45106_GPO_REG, value);
+}
+
+static int slg7xl45106_get_direction(struct gpio_chip *chip,
+				     unsigned offset)
+{
+	/* This device always output */
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int slg7xl45106_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct slg7xl45106 *gpio = gpiochip_get_data(chip);
+	int ret;
+
+	ret = slg7xl45106_read(gpio);
+	if (ret < 0)
+		return ret;
+
+	return !!(ret & BIT(offset));
+}
+
+static void slg7xl45106_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct slg7xl45106 *gpio = gpiochip_get_data(chip);
+	u8 buffer;
+
+	mutex_lock(&gpio->lock);
+
+	buffer = slg7xl45106_read(gpio);
+	if (value)
+		buffer |= BIT(offset);
+	else
+		buffer &= ~BIT(offset);
+
+	slg7xl45106_write(gpio, buffer);
+
+	mutex_unlock(&gpio->lock);
+}
+
+static int slg7xl45106_probe(struct i2c_client *client)
+{
+	struct slg7xl45106 *gpio;
+
+	gpio = devm_kzalloc(&client->dev, sizeof(*gpio), GFP_KERNEL);
+	if (!gpio)
+		return -ENOMEM;
+
+	gpio->chip.label = client->name;
+	gpio->chip.parent = &client->dev;
+	gpio->chip.owner = THIS_MODULE;
+	gpio->chip.get_direction = slg7xl45106_get_direction;
+	gpio->chip.get = slg7xl45106_get;
+	gpio->chip.set = slg7xl45106_set;
+	gpio->chip.base = -1;
+	gpio->chip.ngpio = (uintptr_t)device_get_match_data(&client->dev);
+	gpio->chip.can_sleep = true;
+
+	mutex_init(&gpio->lock);
+
+	i2c_set_clientdata(client, gpio);
+
+	return devm_gpiochip_add_data(&client->dev, &gpio->chip, gpio);
+}
+
+static const struct i2c_device_id slg7xl45106_id_table[] = {
+	{ "slg7xl45106", 8 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, slg7xl45106_id_table);
+
+static const struct of_device_id slg7xl45106_of_match_table[] = {
+	{ .compatible = "dlg,slg7xl45106", .data = (void *)8 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, slg7xl45106_of_match_table);
+
+static struct i2c_driver slg7xl45106_driver = {
+	.driver = {
+		.name = "slg7xl45106",
+		.of_match_table = slg7xl45106_of_match_table,
+	},
+	.probe_new = slg7xl45106_probe,
+	.id_table = slg7xl45106_id_table,
+};
+module_i2c_driver(slg7xl45106_driver);
+
+MODULE_AUTHOR("Raviteja Narayanam <raviteja.narayanam@xilinx.com>");
+MODULE_DESCRIPTION("GPIO expander driver for slg7xl45106");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-stmpe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-stmpe.c
@@ -191,7 +191,7 @@
 		[REG_IE][CSB] = STMPE_IDX_IEGPIOR_CSB,
 		[REG_IE][MSB] = STMPE_IDX_IEGPIOR_MSB,
 	};
-	int i, j;
+	int ret, i, j;
 
 	/*
 	 * STMPE1600: to be able to get IRQ from pins,
@@ -199,8 +199,16 @@
 	 * GPSR or GPCR registers
 	 */
 	if (stmpe->partnum == STMPE1600) {
-		stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_GPMR_LSB]);
-		stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_GPMR_CSB]);
+		ret = stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_GPMR_LSB]);
+		if (ret < 0) {
+			dev_err(stmpe->dev, "Failed to read GPMR_LSB: %d\n", ret);
+			goto err;
+		}
+		ret = stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_GPMR_CSB]);
+		if (ret < 0) {
+			dev_err(stmpe->dev, "Failed to read GPMR_CSB: %d\n", ret);
+			goto err;
+		}
 	}
 
 	for (i = 0; i < CACHE_NR_REGS; i++) {
@@ -222,6 +230,7 @@
 		}
 	}
 
+err:
 	mutex_unlock(&stmpe_gpio->irq_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-tb10x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-tb10x.c
@@ -62,14 +62,14 @@
 	u32 r;
 	unsigned long flags;
 
-	spin_lock_irqsave(&gpio->gc.bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gpio->gc.bgpio_lock, flags);
 
 	r = tb10x_reg_read(gpio, offs);
 	r = (r & ~mask) | (val & mask);
 
 	tb10x_reg_write(gpio, offs, r);
 
-	spin_unlock_irqrestore(&gpio->gc.bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->gc.bgpio_lock, flags);
 }
 
 static int tb10x_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
@@ -195,7 +195,7 @@
 				handle_edge_irq, IRQ_NOREQUEST, IRQ_NOPROBE,
 				IRQ_GC_INIT_MASK_CACHE);
 		if (ret)
-			return ret;
+			goto err_remove_domain;
 
 		gc = tb10x_gpio->domain->gc->gc[0];
 		gc->reg_base                         = tb10x_gpio->base;
@@ -209,6 +209,10 @@
 	}
 
 	return 0;
+
+err_remove_domain:
+	irq_domain_remove(tb10x_gpio->domain);
+	return ret;
 }
 
 static int tb10x_gpio_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-tegra186.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-tegra186.c
@@ -337,9 +337,12 @@
 	return offset + pin;
 }
 
+#define to_tegra_gpio(x) container_of((x), struct tegra_gpio, gpio)
+
 static void tegra186_irq_ack(struct irq_data *data)
 {
-	struct tegra_gpio *gpio = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct tegra_gpio *gpio = to_tegra_gpio(gc);
 	void __iomem *base;
 
 	base = tegra186_gpio_get_base(gpio, data->hwirq);
@@ -351,7 +354,8 @@
 
 static void tegra186_irq_mask(struct irq_data *data)
 {
-	struct tegra_gpio *gpio = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct tegra_gpio *gpio = to_tegra_gpio(gc);
 	void __iomem *base;
 	u32 value;
 
@@ -366,7 +370,8 @@
 
 static void tegra186_irq_unmask(struct irq_data *data)
 {
-	struct tegra_gpio *gpio = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct tegra_gpio *gpio = to_tegra_gpio(gc);
 	void __iomem *base;
 	u32 value;
 
@@ -381,7 +386,8 @@
 
 static int tegra186_irq_set_type(struct irq_data *data, unsigned int type)
 {
-	struct tegra_gpio *gpio = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct tegra_gpio *gpio = to_tegra_gpio(gc);
 	void __iomem *base;
 	u32 value;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-timberdale.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-timberdale.c
@@ -43,9 +43,10 @@
 	unsigned offset, bool enabled)
 {
 	struct timbgpio *tgpio = gpiochip_get_data(gpio);
+	unsigned long flags;
 	u32 reg;
 
-	spin_lock(&tgpio->lock);
+	spin_lock_irqsave(&tgpio->lock, flags);
 	reg = ioread32(tgpio->membase + offset);
 
 	if (enabled)
@@ -54,7 +55,7 @@
 		reg &= ~(1 << index);
 
 	iowrite32(reg, tgpio->membase + offset);
-	spin_unlock(&tgpio->lock);
+	spin_unlock_irqrestore(&tgpio->lock, flags);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-tps68470.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-tps68470.c
@@ -91,13 +91,13 @@
 	struct tps68470_gpio_data *tps68470_gpio = gpiochip_get_data(gc);
 	struct regmap *regmap = tps68470_gpio->tps68470_regmap;
 
+	/* Set the initial value */
+	tps68470_gpio_set(gc, offset, value);
+
 	/* rest are always outputs */
 	if (offset >= TPS68470_N_REGULAR_GPIO)
 		return 0;
 
-	/* Set the initial value */
-	tps68470_gpio_set(gc, offset, value);
-
 	return regmap_update_bits(regmap, TPS68470_GPIO_CTL_REG_A(offset),
 				 TPS68470_GPIO_MODE_MASK,
 				 TPS68470_GPIO_MODE_OUT_CMOS);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-tqmx86.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-tqmx86.c
@@ -27,16 +27,20 @@
 #define TQMX86_GPIIC	3	/* GPI Interrupt Configuration Register */
 #define TQMX86_GPIIS	4	/* GPI Interrupt Status Register */
 
+#define TQMX86_GPII_NONE	0
 #define TQMX86_GPII_FALLING	BIT(0)
 #define TQMX86_GPII_RISING	BIT(1)
 #define TQMX86_GPII_MASK	(BIT(0) | BIT(1))
 #define TQMX86_GPII_BITS	2
+/* Stored in irq_type with GPII bits */
+#define TQMX86_INT_UNMASKED	BIT(2)
 
 struct tqmx86_gpio_data {
 	struct gpio_chip	chip;
 	struct irq_chip		irq_chip;
 	void __iomem		*io_base;
 	int			irq;
+	/* Lock must be held for accessing output and irq_type fields */
 	raw_spinlock_t		spinlock;
 	u8			irq_type[TQMX86_NGPI];
 };
@@ -107,20 +111,30 @@
 	return GPIO_LINE_DIRECTION_OUT;
 }
 
+static void tqmx86_gpio_irq_config(struct tqmx86_gpio_data *gpio, int offset)
+	__must_hold(&gpio->spinlock)
+{
+	u8 type = TQMX86_GPII_NONE, gpiic;
+
+	if (gpio->irq_type[offset] & TQMX86_INT_UNMASKED)
+		type = gpio->irq_type[offset] & TQMX86_GPII_MASK;
+
+	gpiic = tqmx86_gpio_read(gpio, TQMX86_GPIIC);
+	gpiic &= ~(TQMX86_GPII_MASK << (offset * TQMX86_GPII_BITS));
+	gpiic |= type << (offset * TQMX86_GPII_BITS);
+	tqmx86_gpio_write(gpio, gpiic, TQMX86_GPIIC);
+}
+
 static void tqmx86_gpio_irq_mask(struct irq_data *data)
 {
 	unsigned int offset = (data->hwirq - TQMX86_NGPO);
 	struct tqmx86_gpio_data *gpio = gpiochip_get_data(
 		irq_data_get_irq_chip_data(data));
 	unsigned long flags;
-	u8 gpiic, mask;
-
-	mask = TQMX86_GPII_MASK << (offset * TQMX86_GPII_BITS);
 
 	raw_spin_lock_irqsave(&gpio->spinlock, flags);
-	gpiic = tqmx86_gpio_read(gpio, TQMX86_GPIIC);
-	gpiic &= ~mask;
-	tqmx86_gpio_write(gpio, gpiic, TQMX86_GPIIC);
+	gpio->irq_type[offset] &= ~TQMX86_INT_UNMASKED;
+	tqmx86_gpio_irq_config(gpio, offset);
 	raw_spin_unlock_irqrestore(&gpio->spinlock, flags);
 }
 
@@ -130,15 +144,10 @@
 	struct tqmx86_gpio_data *gpio = gpiochip_get_data(
 		irq_data_get_irq_chip_data(data));
 	unsigned long flags;
-	u8 gpiic, mask;
-
-	mask = TQMX86_GPII_MASK << (offset * TQMX86_GPII_BITS);
 
 	raw_spin_lock_irqsave(&gpio->spinlock, flags);
-	gpiic = tqmx86_gpio_read(gpio, TQMX86_GPIIC);
-	gpiic &= ~mask;
-	gpiic |= gpio->irq_type[offset] << (offset * TQMX86_GPII_BITS);
-	tqmx86_gpio_write(gpio, gpiic, TQMX86_GPIIC);
+	gpio->irq_type[offset] |= TQMX86_INT_UNMASKED;
+	tqmx86_gpio_irq_config(gpio, offset);
 	raw_spin_unlock_irqrestore(&gpio->spinlock, flags);
 }
 
@@ -149,7 +158,7 @@
 	unsigned int offset = (data->hwirq - TQMX86_NGPO);
 	unsigned int edge_type = type & IRQF_TRIGGER_MASK;
 	unsigned long flags;
-	u8 new_type, gpiic;
+	u8 new_type;
 
 	switch (edge_type) {
 	case IRQ_TYPE_EDGE_RISING:
@@ -165,13 +174,10 @@
 		return -EINVAL; /* not supported */
 	}
 
-	gpio->irq_type[offset] = new_type;
-
 	raw_spin_lock_irqsave(&gpio->spinlock, flags);
-	gpiic = tqmx86_gpio_read(gpio, TQMX86_GPIIC);
-	gpiic &= ~((TQMX86_GPII_MASK) << (offset * TQMX86_GPII_BITS));
-	gpiic |= new_type << (offset * TQMX86_GPII_BITS);
-	tqmx86_gpio_write(gpio, gpiic, TQMX86_GPIIC);
+	gpio->irq_type[offset] &= ~TQMX86_GPII_MASK;
+	gpio->irq_type[offset] |= new_type;
+	tqmx86_gpio_irq_config(gpio, offset);
 	raw_spin_unlock_irqrestore(&gpio->spinlock, flags);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-ts4900.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-ts4900.c
@@ -1,7 +1,7 @@
 /*
  * Digital I/O driver for Technologic Systems I2C FPGA Core
  *
- * Copyright (C) 2015 Technologic Systems
+ * Copyright (C) 2015, 2018 Technologic Systems
  * Copyright (C) 2016 Savoir-Faire Linux
  *
  * This program is free software; you can redistribute it and/or
@@ -55,19 +55,33 @@
 {
 	struct ts4900_gpio_priv *priv = gpiochip_get_data(chip);
 
-	/*
-	 * This will clear the output enable bit, the other bits are
-	 * dontcare when this is cleared
+	/* Only clear the OE bit here, requires a RMW. Prevents potential issue
+	 * with OE and data getting to the physical pin at different times.
 	 */
-	return regmap_write(priv->regmap, offset, 0);
+	return regmap_update_bits(priv->regmap, offset, TS4900_GPIO_OE, 0);
 }
 
 static int ts4900_gpio_direction_output(struct gpio_chip *chip,
 					unsigned int offset, int value)
 {
 	struct ts4900_gpio_priv *priv = gpiochip_get_data(chip);
+	unsigned int reg;
 	int ret;
 
+	/* If changing from an input to an output, we need to first set the
+	 * proper data bit to what is requested and then set OE bit. This
+	 * prevents a glitch that can occur on the IO line
+	 */
+	regmap_read(priv->regmap, offset, &reg);
+	if (!(reg & TS4900_GPIO_OE)) {
+		if (value)
+			reg = TS4900_GPIO_OUT;
+		else
+			reg &= ~TS4900_GPIO_OUT;
+
+		regmap_write(priv->regmap, offset, reg);
+	}
+
 	if (value)
 		ret = regmap_write(priv->regmap, offset, TS4900_GPIO_OE |
 							 TS4900_GPIO_OUT);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-vf610.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-vf610.c
@@ -125,12 +125,16 @@
 {
 	struct vf610_gpio_port *port = gpiochip_get_data(chip);
 	unsigned long mask = BIT(gpio);
-
-	if (port->sdata && port->sdata->have_paddr)
-		vf610_gpio_writel(mask, port->gpio_base + GPIO_PDDR);
+	u32 val;
 
 	vf610_gpio_set(chip, gpio, value);
 
+	if (port->sdata && port->sdata->have_paddr) {
+		val = vf610_gpio_readl(port->gpio_base + GPIO_PDDR);
+		val |= mask;
+		vf610_gpio_writel(val, port->gpio_base + GPIO_PDDR);
+	}
+
 	return pinctrl_gpio_direction_output(chip->base + gpio);
 }
 
@@ -300,7 +304,7 @@
 	gc = &port->gc;
 	gc->of_node = np;
 	gc->parent = dev;
-	gc->label = "vf610-gpio";
+	gc->label = dev_name(dev);
 	gc->ngpio = VF610_GPIO_PER_PORT;
 	gc->base = of_alias_get_id(np, "gpio") * VF610_GPIO_PER_PORT;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-virtio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-virtio.c
@@ -81,11 +81,7 @@
 	virtqueue_kick(vgpio->request_vq);
 	mutex_unlock(&vgpio->lock);
 
-	if (!wait_for_completion_timeout(&line->completion, HZ)) {
-		dev_err(dev, "GPIO operation timed out\n");
-		ret = -ETIMEDOUT;
-		goto out;
-	}
+	wait_for_completion(&line->completion);
 
 	if (unlikely(res->status != VIRTIO_GPIO_STATUS_OK)) {
 		dev_err(dev, "GPIO request failed: %d\n", gpio);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-visconti.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-visconti.c
@@ -130,7 +130,6 @@
 	struct gpio_irq_chip *girq;
 	struct irq_domain *parent;
 	struct device_node *irq_parent;
-	struct fwnode_handle *fwnode;
 	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -150,14 +149,12 @@
 	}
 
 	parent = irq_find_host(irq_parent);
+	of_node_put(irq_parent);
 	if (!parent) {
 		dev_err(dev, "No IRQ parent domain\n");
 		return -ENODEV;
 	}
 
-	fwnode = of_node_to_fwnode(irq_parent);
-	of_node_put(irq_parent);
-
 	ret = bgpio_init(&priv->gpio_chip, dev, 4,
 			 priv->base + GPIO_IDATA,
 			 priv->base + GPIO_OSET,
@@ -180,7 +177,7 @@
 
 	girq = &priv->gpio_chip.irq;
 	girq->chip = irq_chip;
-	girq->fwnode = fwnode;
+	girq->fwnode = of_node_to_fwnode(dev->of_node);
 	girq->parent_domain = parent;
 	girq->child_to_parent_hwirq = visconti_gpio_child_to_parent_hwirq;
 	girq->populate_parent_alloc_arg = visconti_gpio_populate_parent_fwspec;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-vr41xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-vr41xx.c
@@ -217,8 +217,6 @@
 	printk(KERN_ERR "spurious GIU interrupt: %04x(%04x),%04x(%04x)\n",
 	       maskl, pendl, maskh, pendh);
 
-	atomic_inc(&irq_err_count);
-
 	return -EINVAL;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-wcove.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-wcove.c
@@ -104,7 +104,7 @@
 	unsigned int reg = type == CTRL_IN ? GPIO_IN_CTRL_BASE : GPIO_OUT_CTRL_BASE;
 
 	if (gpio >= WCOVE_GPIO_NUM)
-		return -EOPNOTSUPP;
+		return -ENOTSUPP;
 
 	return reg + gpio;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-winbond.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-winbond.c
@@ -385,12 +385,13 @@
 	unsigned long *base = gpiochip_get_data(gc);
 	const struct winbond_gpio_info *info;
 	bool val;
+	int ret;
 
 	winbond_gpio_get_info(&offset, &info);
 
-	val = winbond_sio_enter(*base);
-	if (val)
-		return val;
+	ret = winbond_sio_enter(*base);
+	if (ret)
+		return ret;
 
 	winbond_sio_select_logical(*base, info->dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-xilinx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-xilinx.c
@@ -52,7 +52,6 @@
  * @dir: GPIO direction shadow register
  * @gpio_lock: Lock used for synchronization
  * @irq: IRQ used by GPIO device
- * @irqchip: IRQ chip
  * @enable: GPIO IRQ enable/disable bitfield
  * @rising_edge: GPIO IRQ rising edge enable/disable bitfield
  * @falling_edge: GPIO IRQ falling edge enable/disable bitfield
@@ -66,7 +65,7 @@
 	DECLARE_BITMAP(state, 64);
 	DECLARE_BITMAP(last_irq_read, 64);
 	DECLARE_BITMAP(dir, 64);
-	spinlock_t gpio_lock;	/* For serializing operations */
+	raw_spinlock_t gpio_lock;	/* For serializing operations */
 	int irq;
 	struct irq_chip irqchip;
 	DECLARE_BITMAP(enable, 64);
@@ -99,7 +98,7 @@
 	const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);
 
 	map[index] &= ~(0xFFFFFFFFul << offset);
-	map[index] |= v << offset;
+	map[index] |= (unsigned long)v << offset;
 }
 
 static inline int xgpio_regoffset(struct xgpio_instance *chip, int ch)
@@ -117,12 +116,14 @@
 static void xgpio_read_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
 {
 	void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);
+
 	xgpio_set_value32(a, bit, xgpio_readreg(addr));
 }
 
 static void xgpio_write_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
 {
 	void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);
+
 	xgpio_writereg(addr, xgpio_get_value32(a, bit));
 }
 
@@ -179,14 +180,14 @@
 	struct xgpio_instance *chip = gpiochip_get_data(gc);
 	int bit = xgpio_to_bit(chip, gpio);
 
-	spin_lock_irqsave(&chip->gpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gpio_lock, flags);
 
 	/* Write to GPIO signal and set its direction to output */
 	__assign_bit(bit, chip->state, val);
 
 	xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);
 
-	spin_unlock_irqrestore(&chip->gpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gpio_lock, flags);
 }
 
 /**
@@ -210,7 +211,7 @@
 	bitmap_remap(hw_mask, mask, chip->sw_map, chip->hw_map, 64);
 	bitmap_remap(hw_bits, bits, chip->sw_map, chip->hw_map, 64);
 
-	spin_lock_irqsave(&chip->gpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gpio_lock, flags);
 
 	bitmap_replace(state, chip->state, hw_bits, hw_mask, 64);
 
@@ -218,7 +219,7 @@
 
 	bitmap_copy(chip->state, state, 64);
 
-	spin_unlock_irqrestore(&chip->gpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gpio_lock, flags);
 }
 
 /**
@@ -236,13 +237,13 @@
 	struct xgpio_instance *chip = gpiochip_get_data(gc);
 	int bit = xgpio_to_bit(chip, gpio);
 
-	spin_lock_irqsave(&chip->gpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gpio_lock, flags);
 
 	/* Set the GPIO bit in shadow register and set direction as input */
 	__set_bit(bit, chip->dir);
 	xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);
 
-	spin_unlock_irqrestore(&chip->gpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gpio_lock, flags);
 
 	return 0;
 }
@@ -265,7 +266,7 @@
 	struct xgpio_instance *chip = gpiochip_get_data(gc);
 	int bit = xgpio_to_bit(chip, gpio);
 
-	spin_lock_irqsave(&chip->gpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gpio_lock, flags);
 
 	/* Write state of GPIO signal */
 	__assign_bit(bit, chip->state, val);
@@ -275,7 +276,7 @@
 	__clear_bit(bit, chip->dir);
 	xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);
 
-	spin_unlock_irqrestore(&chip->gpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gpio_lock, flags);
 
 	return 0;
 }
@@ -405,7 +406,7 @@
 	int bit = xgpio_to_bit(chip, irq_offset);
 	u32 mask = BIT(bit / 32), temp;
 
-	spin_lock_irqsave(&chip->gpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gpio_lock, flags);
 
 	__clear_bit(bit, chip->enable);
 
@@ -415,7 +416,7 @@
 		temp &= ~mask;
 		xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, temp);
 	}
-	spin_unlock_irqrestore(&chip->gpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gpio_lock, flags);
 }
 
 /**
@@ -431,7 +432,7 @@
 	u32 old_enable = xgpio_get_value32(chip->enable, bit);
 	u32 mask = BIT(bit / 32), val;
 
-	spin_lock_irqsave(&chip->gpio_lock, flags);
+	raw_spin_lock_irqsave(&chip->gpio_lock, flags);
 
 	__set_bit(bit, chip->enable);
 
@@ -450,7 +451,7 @@
 		xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, val);
 	}
 
-	spin_unlock_irqrestore(&chip->gpio_lock, flags);
+	raw_spin_unlock_irqrestore(&chip->gpio_lock, flags);
 }
 
 /**
@@ -515,7 +516,7 @@
 
 	chained_irq_enter(irqchip, desc);
 
-	spin_lock(&chip->gpio_lock);
+	raw_spin_lock(&chip->gpio_lock);
 
 	xgpio_read_ch_all(chip, XGPIO_DATA_OFFSET, all);
 
@@ -532,7 +533,7 @@
 	bitmap_copy(chip->last_irq_read, all, 64);
 	bitmap_or(all, rising, falling, 64);
 
-	spin_unlock(&chip->gpio_lock);
+	raw_spin_unlock(&chip->gpio_lock);
 
 	dev_dbg(gc->parent, "IRQ rising %*pb falling %*pb\n", 64, rising, 64, falling);
 
@@ -623,7 +624,7 @@
 	bitmap_set(chip->hw_map,  0, width[0]);
 	bitmap_set(chip->hw_map, 32, width[1]);
 
-	spin_lock_init(&chip->gpio_lock);
+	raw_spin_lock_init(&chip->gpio_lock);
 
 	chip->gc.base = -1;
 	chip->gc.ngpio = bitmap_weight(chip->hw_map, 64);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpio-zynqmp-modepin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpio-zynqmp-modepin.c
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the ps-mode pin configuration.
+ *
+ * Copyright (c) 2021 Xilinx, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+/* 4-bit boot mode pins */
+#define MODE_PINS			4
+
+/**
+ * modepin_gpio_get_value - Get the state of the specified pin of GPIO device
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * This function reads the state of the specified pin of the GPIO device.
+ *
+ * Return: 0 if the pin is low, 1 if pin is high, -EINVAL wrong pin configured
+ *         or error value.
+ */
+static int modepin_gpio_get_value(struct gpio_chip *chip, unsigned int pin)
+{
+	u32 regval = 0;
+	int ret;
+
+	ret = zynqmp_pm_bootmode_read(&regval);
+	if (ret)
+		return ret;
+
+	/* When [0:3] corresponding bit is set, then read output bit [8:11],
+	 * if the bit is clear then read input bit [4:7] for status or value.
+	 */
+	if (regval & BIT(pin))
+		return !!(regval & BIT(pin + 8));
+	else
+		return !!(regval & BIT(pin + 4));
+}
+
+/**
+ * modepin_gpio_set_value - Modify the state of the pin with specified value
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ * @state:	value used to modify the state of the specified pin
+ *
+ * This function reads the state of the specified pin of the GPIO device, mask
+ * with the capture state of GPIO pin, and update pin of GPIO device.
+ *
+ * Return:	None.
+ */
+static void modepin_gpio_set_value(struct gpio_chip *chip, unsigned int pin,
+				   int state)
+{
+	u32 bootpin_val = 0;
+	int ret;
+
+	zynqmp_pm_bootmode_read(&bootpin_val);
+
+	/* Configure pin as an output by set bit [0:3] */
+	bootpin_val |= BIT(pin);
+
+	if (state)
+		bootpin_val |= BIT(pin + 8);
+	else
+		bootpin_val &= ~BIT(pin + 8);
+
+	/* Configure bootpin value */
+	ret = zynqmp_pm_bootmode_write(bootpin_val);
+	if (ret)
+		pr_err("modepin: set value error %d for pin %d\n", ret, pin);
+}
+
+/**
+ * modepin_gpio_dir_in - Set the direction of the specified GPIO pin as input
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * Return: 0 always
+ */
+static int modepin_gpio_dir_in(struct gpio_chip *chip, unsigned int pin)
+{
+	return 0;
+}
+
+/**
+ * modepin_gpio_dir_out - Set the direction of the specified GPIO pin as output
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ * @state:	value to be written to specified pin
+ *
+ * Return: 0 always
+ */
+static int modepin_gpio_dir_out(struct gpio_chip *chip, unsigned int pin,
+				int state)
+{
+	return 0;
+}
+
+/**
+ * modepin_gpio_probe - Initialization method for modepin_gpio
+ * @pdev:		platform device instance
+ *
+ * Return: 0 on success, negative error otherwise.
+ */
+static int modepin_gpio_probe(struct platform_device *pdev)
+{
+	struct gpio_chip *chip;
+	int status;
+
+	chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, chip);
+
+	/* configure the gpio chip */
+	chip->base = -1;
+	chip->ngpio = MODE_PINS;
+	chip->owner = THIS_MODULE;
+	chip->parent = &pdev->dev;
+	chip->get = modepin_gpio_get_value;
+	chip->set = modepin_gpio_set_value;
+	chip->direction_input = modepin_gpio_dir_in;
+	chip->direction_output = modepin_gpio_dir_out;
+	chip->label = dev_name(&pdev->dev);
+
+	/* modepin gpio registration */
+	status = devm_gpiochip_add_data(&pdev->dev, chip, chip);
+	if (status)
+		return dev_err_probe(&pdev->dev, status,
+			      "Failed to add GPIO chip\n");
+
+	return status;
+}
+
+static const struct of_device_id modepin_platform_id[] = {
+	{ .compatible = "xlnx,zynqmp-gpio-modepin", },
+	{ }
+};
+
+static struct platform_driver modepin_platform_driver = {
+	.driver = {
+		.name = "modepin-gpio",
+		.of_match_table = modepin_platform_id,
+	},
+	.probe = modepin_gpio_probe,
+};
+
+module_platform_driver(modepin_platform_driver);
+
+MODULE_AUTHOR("Piyush Mehta <piyush.mehta@xilinx.com>");
+MODULE_DESCRIPTION("ZynqMP Boot PS_MODE Configuration");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpiolib-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpiolib-acpi.c
@@ -311,7 +311,8 @@
 	if (IS_ERR(desc))
 		return desc;
 
-	ret = gpio_set_debounce_timeout(desc, agpio->debounce_timeout);
+	/* ACPI uses hundredths of milliseconds units */
+	ret = gpio_set_debounce_timeout(desc, agpio->debounce_timeout * 10);
 	if (ret)
 		dev_warn(chip->parent,
 			 "Failed to set debounce-timeout for pin 0x%04X, err %d\n",
@@ -391,8 +392,8 @@
 	pin = agpio->pin_table[0];
 
 	if (pin <= 255) {
-		char ev_name[5];
-		sprintf(ev_name, "_%c%02hhX",
+		char ev_name[8];
+		sprintf(ev_name, "_%c%02X",
 			agpio->triggering == ACPI_EDGE_SENSITIVE ? 'E' : 'L',
 			pin);
 		if (ACPI_SUCCESS(acpi_get_handle(handle, ev_name, &evt_handle)))
@@ -1052,17 +1053,25 @@
 			if (ret < 0)
 				return ret;
 
-			ret = gpio_set_debounce_timeout(desc, info.debounce);
+			/* ACPI uses hundredths of milliseconds units */
+			ret = gpio_set_debounce_timeout(desc, info.debounce * 10);
 			if (ret)
 				return ret;
 
 			irq_flags = acpi_dev_get_irq_type(info.triggering,
 							  info.polarity);
 
-			/* Set type if specified and different than the current one */
-			if (irq_flags != IRQ_TYPE_NONE &&
-			    irq_flags != irq_get_trigger_type(irq))
-				irq_set_irq_type(irq, irq_flags);
+			/*
+			 * If the IRQ is not already in use then set type
+			 * if specified and different than the current one.
+			 */
+			if (can_request_irq(irq, irq_flags)) {
+				if (irq_flags != IRQ_TYPE_NONE &&
+				    irq_flags != irq_get_trigger_type(irq))
+					irq_set_irq_type(irq, irq_flags);
+			} else {
+				dev_dbg(&adev->dev, "IRQ %d already in use\n", irq);
+			}
 
 			return irq;
 		}
@@ -1563,6 +1572,20 @@
 			.ignore_wake = "INT33FF:01@0",
 		},
 	},
+	{
+		/*
+		 * Spurious wakeups from TP_ATTN# pin
+		 * Found in BIOS 0.35
+		 * https://gitlab.freedesktop.org/drm/amd/-/issues/3073
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GPD"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "G1619-04"),
+		},
+		.driver_data = &(struct acpi_gpiolib_dmi_quirk) {
+			.ignore_wake = "PNP0C50:00@8",
+		},
+	},
 	{} /* Terminating entry */
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpiolib-cdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpiolib-cdev.c
@@ -54,6 +54,50 @@
  * interface to gpiolib GPIOs via ioctl()s.
  */
 
+typedef __poll_t (*poll_fn)(struct file *, struct poll_table_struct *);
+typedef long (*ioctl_fn)(struct file *, unsigned int, unsigned long);
+typedef ssize_t (*read_fn)(struct file *, char __user *,
+			   size_t count, loff_t *);
+
+static __poll_t call_poll_locked(struct file *file,
+				 struct poll_table_struct *wait,
+				 struct gpio_device *gdev, poll_fn func)
+{
+	__poll_t ret;
+
+	down_read(&gdev->sem);
+	ret = func(file, wait);
+	up_read(&gdev->sem);
+
+	return ret;
+}
+
+static long call_ioctl_locked(struct file *file, unsigned int cmd,
+			      unsigned long arg, struct gpio_device *gdev,
+			      ioctl_fn func)
+{
+	long ret;
+
+	down_read(&gdev->sem);
+	ret = func(file, cmd, arg);
+	up_read(&gdev->sem);
+
+	return ret;
+}
+
+static ssize_t call_read_locked(struct file *file, char __user *buf,
+				size_t count, loff_t *f_ps,
+				struct gpio_device *gdev, read_fn func)
+{
+	ssize_t ret;
+
+	down_read(&gdev->sem);
+	ret = func(file, buf, count, f_ps);
+	up_read(&gdev->sem);
+
+	return ret;
+}
+
 /*
  * GPIO line handle management
  */
@@ -83,6 +127,10 @@
 	GPIOHANDLE_REQUEST_OPEN_DRAIN | \
 	GPIOHANDLE_REQUEST_OPEN_SOURCE)
 
+#define GPIOHANDLE_REQUEST_DIRECTION_FLAGS \
+	(GPIOHANDLE_REQUEST_INPUT | \
+	 GPIOHANDLE_REQUEST_OUTPUT)
+
 static int linehandle_validate_flags(u32 flags)
 {
 	/* Return an error if an unknown flag is set */
@@ -163,21 +211,21 @@
 	if (ret)
 		return ret;
 
+	/* Lines must be reconfigured explicitly as input or output. */
+	if (!(lflags & GPIOHANDLE_REQUEST_DIRECTION_FLAGS))
+		return -EINVAL;
+
 	for (i = 0; i < lh->num_descs; i++) {
 		desc = lh->descs[i];
-		linehandle_flags_to_desc_flags(gcnf.flags, &desc->flags);
+		linehandle_flags_to_desc_flags(lflags, &desc->flags);
 
-		/*
-		 * Lines have to be requested explicitly for input
-		 * or output, else the line will be treated "as is".
-		 */
 		if (lflags & GPIOHANDLE_REQUEST_OUTPUT) {
 			int val = !!gcnf.default_values[i];
 
 			ret = gpiod_direction_output(desc, val);
 			if (ret)
 				return ret;
-		} else if (lflags & GPIOHANDLE_REQUEST_INPUT) {
+		} else {
 			ret = gpiod_direction_input(desc);
 			if (ret)
 				return ret;
@@ -190,23 +238,25 @@
 	return 0;
 }
 
-static long linehandle_ioctl(struct file *file, unsigned int cmd,
-			     unsigned long arg)
+static long linehandle_ioctl_unlocked(struct file *file, unsigned int cmd,
+				      unsigned long arg)
 {
 	struct linehandle_state *lh = file->private_data;
 	void __user *ip = (void __user *)arg;
 	struct gpiohandle_data ghd;
 	DECLARE_BITMAP(vals, GPIOHANDLES_MAX);
-	int i;
+	unsigned int i;
+	int ret;
 
-	if (cmd == GPIOHANDLE_GET_LINE_VALUES_IOCTL) {
-		/* NOTE: It's ok to read values of output lines. */
-		int ret = gpiod_get_array_value_complex(false,
-							true,
-							lh->num_descs,
-							lh->descs,
-							NULL,
-							vals);
+	if (!lh->gdev->chip)
+		return -ENODEV;
+
+	switch (cmd) {
+	case GPIOHANDLE_GET_LINE_VALUES_IOCTL:
+		/* NOTE: It's okay to read values of output lines */
+		ret = gpiod_get_array_value_complex(false, true,
+						    lh->num_descs, lh->descs,
+						    NULL, vals);
 		if (ret)
 			return ret;
 
@@ -218,7 +268,7 @@
 			return -EFAULT;
 
 		return 0;
-	} else if (cmd == GPIOHANDLE_SET_LINE_VALUES_IOCTL) {
+	case GPIOHANDLE_SET_LINE_VALUES_IOCTL:
 		/*
 		 * All line descriptors were created at once with the same
 		 * flags so just check if the first one is really output.
@@ -240,10 +290,20 @@
 						     lh->descs,
 						     NULL,
 						     vals);
-	} else if (cmd == GPIOHANDLE_SET_CONFIG_IOCTL) {
+	case GPIOHANDLE_SET_CONFIG_IOCTL:
 		return linehandle_set_config(lh, ip);
+	default:
+		return -EINVAL;
 	}
-	return -EINVAL;
+}
+
+static long linehandle_ioctl(struct file *file, unsigned int cmd,
+			     unsigned long arg)
+{
+	struct linehandle_state *lh = file->private_data;
+
+	return call_ioctl_locked(file, cmd, arg, lh->gdev,
+				 linehandle_ioctl_unlocked);
 }
 
 #ifdef CONFIG_COMPAT
@@ -330,7 +390,7 @@
 			goto out_free_lh;
 		}
 
-		ret = gpiod_request(desc, lh->label);
+		ret = gpiod_request_user(desc, lh->label);
 		if (ret)
 			goto out_free_lh;
 		lh->descs[i] = desc;
@@ -1126,15 +1186,18 @@
 	for (i = 0; i < lr->num_lines; i++) {
 		desc = lr->lines[i].desc;
 		flags = gpio_v2_line_config_flags(lc, i);
+		/*
+		 * Lines not explicitly reconfigured as input or output
+		 * are left unchanged.
+		 */
+		if (!(flags & GPIO_V2_LINE_DIRECTION_FLAGS))
+			continue;
+
 		polarity_change =
 			(!!test_bit(FLAG_ACTIVE_LOW, &desc->flags) !=
 			 ((flags & GPIO_V2_LINE_FLAG_ACTIVE_LOW) != 0));
 
 		gpio_v2_line_config_flags_to_desc_flags(flags, &desc->flags);
-		/*
-		 * Lines have to be requested explicitly for input
-		 * or output, else the line will be treated "as is".
-		 */
 		if (flags & GPIO_V2_LINE_FLAG_OUTPUT) {
 			int val = gpio_v2_line_config_output_value(lc, i);
 
@@ -1142,7 +1205,7 @@
 			ret = gpiod_direction_output(desc, val);
 			if (ret)
 				return ret;
-		} else if (flags & GPIO_V2_LINE_FLAG_INPUT) {
+		} else {
 			ret = gpiod_direction_input(desc);
 			if (ret)
 				return ret;
@@ -1182,20 +1245,34 @@
 	return ret;
 }
 
-static long linereq_ioctl(struct file *file, unsigned int cmd,
-			  unsigned long arg)
+static long linereq_ioctl_unlocked(struct file *file, unsigned int cmd,
+				   unsigned long arg)
 {
 	struct linereq *lr = file->private_data;
 	void __user *ip = (void __user *)arg;
 
-	if (cmd == GPIO_V2_LINE_GET_VALUES_IOCTL)
+	if (!lr->gdev->chip)
+		return -ENODEV;
+
+	switch (cmd) {
+	case GPIO_V2_LINE_GET_VALUES_IOCTL:
 		return linereq_get_values(lr, ip);
-	else if (cmd == GPIO_V2_LINE_SET_VALUES_IOCTL)
+	case GPIO_V2_LINE_SET_VALUES_IOCTL:
 		return linereq_set_values(lr, ip);
-	else if (cmd == GPIO_V2_LINE_SET_CONFIG_IOCTL)
+	case GPIO_V2_LINE_SET_CONFIG_IOCTL:
 		return linereq_set_config(lr, ip);
+	default:
+		return -EINVAL;
+	}
+}
 
-	return -EINVAL;
+static long linereq_ioctl(struct file *file, unsigned int cmd,
+			  unsigned long arg)
+{
+	struct linereq *lr = file->private_data;
+
+	return call_ioctl_locked(file, cmd, arg, lr->gdev,
+				 linereq_ioctl_unlocked);
 }
 
 #ifdef CONFIG_COMPAT
@@ -1206,12 +1283,15 @@
 }
 #endif
 
-static __poll_t linereq_poll(struct file *file,
-			    struct poll_table_struct *wait)
+static __poll_t linereq_poll_unlocked(struct file *file,
+				      struct poll_table_struct *wait)
 {
 	struct linereq *lr = file->private_data;
 	__poll_t events = 0;
 
+	if (!lr->gdev->chip)
+		return EPOLLHUP | EPOLLERR;
+
 	poll_wait(file, &lr->wait, wait);
 
 	if (!kfifo_is_empty_spinlocked_noirqsave(&lr->events,
@@ -1221,16 +1301,25 @@
 	return events;
 }
 
-static ssize_t linereq_read(struct file *file,
-			    char __user *buf,
-			    size_t count,
-			    loff_t *f_ps)
+static __poll_t linereq_poll(struct file *file,
+			     struct poll_table_struct *wait)
+{
+	struct linereq *lr = file->private_data;
+
+	return call_poll_locked(file, wait, lr->gdev, linereq_poll_unlocked);
+}
+
+static ssize_t linereq_read_unlocked(struct file *file, char __user *buf,
+				     size_t count, loff_t *f_ps)
 {
 	struct linereq *lr = file->private_data;
 	struct gpio_v2_line_event le;
 	ssize_t bytes_read = 0;
 	int ret;
 
+	if (!lr->gdev->chip)
+		return -ENODEV;
+
 	if (count < sizeof(le))
 		return -EINVAL;
 
@@ -1275,6 +1364,15 @@
 	return bytes_read;
 }
 
+static ssize_t linereq_read(struct file *file, char __user *buf,
+			    size_t count, loff_t *f_ps)
+{
+	struct linereq *lr = file->private_data;
+
+	return call_read_locked(file, buf, count, f_ps, lr->gdev,
+				linereq_read_unlocked);
+}
+
 static void linereq_free(struct linereq *lr)
 {
 	unsigned int i;
@@ -1378,7 +1476,7 @@
 			goto out_free_linereq;
 		}
 
-		ret = gpiod_request(desc, lr->label);
+		ret = gpiod_request_user(desc, lr->label);
 		if (ret)
 			goto out_free_linereq;
 
@@ -1490,12 +1588,15 @@
 	(GPIOEVENT_REQUEST_RISING_EDGE | \
 	GPIOEVENT_REQUEST_FALLING_EDGE)
 
-static __poll_t lineevent_poll(struct file *file,
-			       struct poll_table_struct *wait)
+static __poll_t lineevent_poll_unlocked(struct file *file,
+					struct poll_table_struct *wait)
 {
 	struct lineevent_state *le = file->private_data;
 	__poll_t events = 0;
 
+	if (!le->gdev->chip)
+		return EPOLLHUP | EPOLLERR;
+
 	poll_wait(file, &le->wait, wait);
 
 	if (!kfifo_is_empty_spinlocked_noirqsave(&le->events, &le->wait.lock))
@@ -1504,15 +1605,21 @@
 	return events;
 }
 
+static __poll_t lineevent_poll(struct file *file,
+			       struct poll_table_struct *wait)
+{
+	struct lineevent_state *le = file->private_data;
+
+	return call_poll_locked(file, wait, le->gdev, lineevent_poll_unlocked);
+}
+
 struct compat_gpioeevent_data {
 	compat_u64	timestamp;
 	u32		id;
 };
 
-static ssize_t lineevent_read(struct file *file,
-			      char __user *buf,
-			      size_t count,
-			      loff_t *f_ps)
+static ssize_t lineevent_read_unlocked(struct file *file, char __user *buf,
+				       size_t count, loff_t *f_ps)
 {
 	struct lineevent_state *le = file->private_data;
 	struct gpioevent_data ge;
@@ -1520,6 +1627,9 @@
 	ssize_t ge_size;
 	int ret;
 
+	if (!le->gdev->chip)
+		return -ENODEV;
+
 	/*
 	 * When compatible system call is being used the struct gpioevent_data,
 	 * in case of at least ia32, has different size due to the alignment
@@ -1577,6 +1687,15 @@
 	return bytes_read;
 }
 
+static ssize_t lineevent_read(struct file *file, char __user *buf,
+			      size_t count, loff_t *f_ps)
+{
+	struct lineevent_state *le = file->private_data;
+
+	return call_read_locked(file, buf, count, f_ps, le->gdev,
+				lineevent_read_unlocked);
+}
+
 static void lineevent_free(struct lineevent_state *le)
 {
 	if (le->irq)
@@ -1594,13 +1713,16 @@
 	return 0;
 }
 
-static long lineevent_ioctl(struct file *file, unsigned int cmd,
-			    unsigned long arg)
+static long lineevent_ioctl_unlocked(struct file *file, unsigned int cmd,
+				     unsigned long arg)
 {
 	struct lineevent_state *le = file->private_data;
 	void __user *ip = (void __user *)arg;
 	struct gpiohandle_data ghd;
 
+	if (!le->gdev->chip)
+		return -ENODEV;
+
 	/*
 	 * We can get the value for an event line but not set it,
 	 * because it is input by definition.
@@ -1623,6 +1745,15 @@
 	return -EINVAL;
 }
 
+static long lineevent_ioctl(struct file *file, unsigned int cmd,
+			    unsigned long arg)
+{
+	struct lineevent_state *le = file->private_data;
+
+	return call_ioctl_locked(file, cmd, arg, le->gdev,
+				 lineevent_ioctl_unlocked);
+}
+
 #ifdef CONFIG_COMPAT
 static long lineevent_ioctl_compat(struct file *file, unsigned int cmd,
 				   unsigned long arg)
@@ -1764,7 +1895,7 @@
 		}
 	}
 
-	ret = gpiod_request(desc, le->label);
+	ret = gpiod_request_user(desc, le->label);
 	if (ret)
 		goto out_free_le;
 	le->desc = desc;
@@ -1784,7 +1915,6 @@
 		ret = -ENODEV;
 		goto out_free_le;
 	}
-	le->irq = irq;
 
 	if (eflags & GPIOEVENT_REQUEST_RISING_EDGE)
 		irqflags |= test_bit(FLAG_ACTIVE_LOW, &desc->flags) ?
@@ -1798,7 +1928,7 @@
 	init_waitqueue_head(&le->wait);
 
 	/* Request a thread to read the events */
-	ret = request_threaded_irq(le->irq,
+	ret = request_threaded_irq(irq,
 				   lineevent_irq_handler,
 				   lineevent_irq_thread,
 				   irqflags,
@@ -1807,6 +1937,8 @@
 	if (ret)
 		goto out_free_le;
 
+	le->irq = irq;
+
 	fd = get_unused_fd_flags(O_RDONLY | O_CLOEXEC);
 	if (fd < 0) {
 		ret = fd;
@@ -2099,10 +2231,7 @@
 	return 0;
 }
 
-/*
- * gpio_ioctl() - ioctl handler for the GPIO chardev
- */
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+static long gpio_ioctl_unlocked(struct file *file, unsigned int cmd, unsigned long arg)
 {
 	struct gpio_chardev_data *cdev = file->private_data;
 	struct gpio_device *gdev = cdev->gdev;
@@ -2113,28 +2242,41 @@
 		return -ENODEV;
 
 	/* Fill in the struct and pass to userspace */
-	if (cmd == GPIO_GET_CHIPINFO_IOCTL) {
+	switch (cmd) {
+	case GPIO_GET_CHIPINFO_IOCTL:
 		return chipinfo_get(cdev, ip);
 #ifdef CONFIG_GPIO_CDEV_V1
-	} else if (cmd == GPIO_GET_LINEHANDLE_IOCTL) {
+	case GPIO_GET_LINEHANDLE_IOCTL:
 		return linehandle_create(gdev, ip);
-	} else if (cmd == GPIO_GET_LINEEVENT_IOCTL) {
+	case GPIO_GET_LINEEVENT_IOCTL:
 		return lineevent_create(gdev, ip);
-	} else if (cmd == GPIO_GET_LINEINFO_IOCTL ||
-		   cmd == GPIO_GET_LINEINFO_WATCH_IOCTL) {
-		return lineinfo_get_v1(cdev, ip,
-				       cmd == GPIO_GET_LINEINFO_WATCH_IOCTL);
+	case GPIO_GET_LINEINFO_IOCTL:
+		return lineinfo_get_v1(cdev, ip, false);
+	case GPIO_GET_LINEINFO_WATCH_IOCTL:
+		return lineinfo_get_v1(cdev, ip, true);
 #endif /* CONFIG_GPIO_CDEV_V1 */
-	} else if (cmd == GPIO_V2_GET_LINEINFO_IOCTL ||
-		   cmd == GPIO_V2_GET_LINEINFO_WATCH_IOCTL) {
-		return lineinfo_get(cdev, ip,
-				    cmd == GPIO_V2_GET_LINEINFO_WATCH_IOCTL);
-	} else if (cmd == GPIO_V2_GET_LINE_IOCTL) {
+	case GPIO_V2_GET_LINEINFO_IOCTL:
+		return lineinfo_get(cdev, ip, false);
+	case GPIO_V2_GET_LINEINFO_WATCH_IOCTL:
+		return lineinfo_get(cdev, ip, true);
+	case GPIO_V2_GET_LINE_IOCTL:
 		return linereq_create(gdev, ip);
-	} else if (cmd == GPIO_GET_LINEINFO_UNWATCH_IOCTL) {
+	case GPIO_GET_LINEINFO_UNWATCH_IOCTL:
 		return lineinfo_unwatch(cdev, ip);
+	default:
+		return -EINVAL;
 	}
-	return -EINVAL;
+}
+
+/*
+ * gpio_ioctl() - ioctl handler for the GPIO chardev
+ */
+static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	struct gpio_chardev_data *cdev = file->private_data;
+
+	return call_ioctl_locked(file, cmd, arg, cdev->gdev,
+				 gpio_ioctl_unlocked);
 }
 
 #ifdef CONFIG_COMPAT
@@ -2176,12 +2318,15 @@
 	return NOTIFY_OK;
 }
 
-static __poll_t lineinfo_watch_poll(struct file *file,
-				    struct poll_table_struct *pollt)
+static __poll_t lineinfo_watch_poll_unlocked(struct file *file,
+					     struct poll_table_struct *pollt)
 {
 	struct gpio_chardev_data *cdev = file->private_data;
 	__poll_t events = 0;
 
+	if (!cdev->gdev->chip)
+		return EPOLLHUP | EPOLLERR;
+
 	poll_wait(file, &cdev->wait, pollt);
 
 	if (!kfifo_is_empty_spinlocked_noirqsave(&cdev->events,
@@ -2191,8 +2336,17 @@
 	return events;
 }
 
-static ssize_t lineinfo_watch_read(struct file *file, char __user *buf,
-				   size_t count, loff_t *off)
+static __poll_t lineinfo_watch_poll(struct file *file,
+				    struct poll_table_struct *pollt)
+{
+	struct gpio_chardev_data *cdev = file->private_data;
+
+	return call_poll_locked(file, pollt, cdev->gdev,
+				lineinfo_watch_poll_unlocked);
+}
+
+static ssize_t lineinfo_watch_read_unlocked(struct file *file, char __user *buf,
+					    size_t count, loff_t *off)
 {
 	struct gpio_chardev_data *cdev = file->private_data;
 	struct gpio_v2_line_info_changed event;
@@ -2200,6 +2354,9 @@
 	int ret;
 	size_t event_size;
 
+	if (!cdev->gdev->chip)
+		return -ENODEV;
+
 #ifndef CONFIG_GPIO_CDEV_V1
 	event_size = sizeof(struct gpio_v2_line_info_changed);
 	if (count < event_size)
@@ -2267,6 +2424,15 @@
 	return bytes_read;
 }
 
+static ssize_t lineinfo_watch_read(struct file *file, char __user *buf,
+				   size_t count, loff_t *off)
+{
+	struct gpio_chardev_data *cdev = file->private_data;
+
+	return call_read_locked(file, buf, count, off, cdev->gdev,
+				lineinfo_watch_read_unlocked);
+}
+
 /**
  * gpio_chrdev_open() - open the chardev for ioctl operations
  * @inode: inode for this chardev
@@ -2280,13 +2446,17 @@
 	struct gpio_chardev_data *cdev;
 	int ret = -ENOMEM;
 
+	down_read(&gdev->sem);
+
 	/* Fail on open if the backing gpiochip is gone */
-	if (!gdev->chip)
-		return -ENODEV;
+	if (!gdev->chip) {
+		ret = -ENODEV;
+		goto out_unlock;
+	}
 
 	cdev = kzalloc(sizeof(*cdev), GFP_KERNEL);
 	if (!cdev)
-		return -ENOMEM;
+		goto out_unlock;
 
 	cdev->watched_lines = bitmap_zalloc(gdev->chip->ngpio, GFP_KERNEL);
 	if (!cdev->watched_lines)
@@ -2309,6 +2479,8 @@
 	if (ret)
 		goto out_unregister_notifier;
 
+	up_read(&gdev->sem);
+
 	return ret;
 
 out_unregister_notifier:
@@ -2318,6 +2490,8 @@
 	bitmap_free(cdev->watched_lines);
 out_free_cdev:
 	kfree(cdev);
+out_unlock:
+	up_read(&gdev->sem);
 	return ret;
 }
 
@@ -2332,9 +2506,9 @@
 	struct gpio_chardev_data *cdev = file->private_data;
 	struct gpio_device *gdev = cdev->gdev;
 
-	bitmap_free(cdev->watched_lines);
 	blocking_notifier_chain_unregister(&gdev->notifier,
 					   &cdev->lineinfo_changed_nb);
+	bitmap_free(cdev->watched_lines);
 	put_device(&gdev->dev);
 	kfree(cdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpiolib-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpiolib-of.c
@@ -130,11 +130,77 @@
 	return false;
 }
 
+/*
+ * Overrides stated polarity of a gpio line and warns when there is a
+ * discrepancy.
+ */
+static void of_gpio_quirk_polarity(const struct device_node *np,
+				   bool active_high,
+				   enum of_gpio_flags *flags)
+{
+	if (active_high) {
+		if (*flags & OF_GPIO_ACTIVE_LOW) {
+			pr_warn("%s GPIO handle specifies active low - ignored\n",
+				of_node_full_name(np));
+			*flags &= ~OF_GPIO_ACTIVE_LOW;
+		}
+	} else {
+		if (!(*flags & OF_GPIO_ACTIVE_LOW))
+			pr_info("%s enforce active low on GPIO handle\n",
+				of_node_full_name(np));
+		*flags |= OF_GPIO_ACTIVE_LOW;
+	}
+}
+
+/*
+ * This quirk does static polarity overrides in cases where existing
+ * DTS specified incorrect polarity.
+ */
+static void of_gpio_try_fixup_polarity(const struct device_node *np,
+				       const char *propname,
+				       enum of_gpio_flags *flags)
+{
+	static const struct {
+		const char *compatible;
+		const char *propname;
+		bool active_high;
+	} gpios[] = {
+#if !IS_ENABLED(CONFIG_LCD_HX8357)
+		/*
+		 * Himax LCD controllers used incorrectly named
+		 * "gpios-reset" property and also specified wrong
+		 * polarity.
+		 */
+		{ "himax,hx8357",	"gpios-reset",	false },
+		{ "himax,hx8369",	"gpios-reset",	false },
+#endif
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_TSC2005)
+		/*
+		 * DTS for Nokia N900 incorrectly specified "active high"
+		 * polarity for the reset line, while the chip actually
+		 * treats it as "active low".
+		 */
+		{ "ti,tsc2005",		"reset-gpios",	false },
+#endif
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(gpios); i++) {
+		if (of_device_is_compatible(np, gpios[i].compatible) &&
+		    !strcmp(propname, gpios[i].propname)) {
+			of_gpio_quirk_polarity(np, gpios[i].active_high, flags);
+			break;
+		}
+	}
+}
+
 static void of_gpio_flags_quirks(const struct device_node *np,
 				 const char *propname,
 				 enum of_gpio_flags *flags,
 				 int index)
 {
+	of_gpio_try_fixup_polarity(np, propname, flags);
+
 	/*
 	 * Some GPIO fixed regulator quirks.
 	 * Note that active low is the default.
@@ -145,7 +211,7 @@
 	     (!(strcmp(propname, "enable-gpio") &&
 		strcmp(propname, "enable-gpios")) &&
 	      of_device_is_compatible(np, "regulator-gpio")))) {
-		bool active_low = !of_property_read_bool(np,
+		bool active_high = of_property_read_bool(np,
 							 "enable-active-high");
 		/*
 		 * The regulator GPIO handles are specified such that the
@@ -153,13 +219,7 @@
 		 * the polarity of the GPIO line. Any phandle flags must
 		 * be actively ignored.
 		 */
-		if ((*flags & OF_GPIO_ACTIVE_LOW) && !active_low) {
-			pr_warn("%s GPIO handle specifies active low - ignored\n",
-				of_node_full_name(np));
-			*flags &= ~OF_GPIO_ACTIVE_LOW;
-		}
-		if (active_low)
-			*flags |= OF_GPIO_ACTIVE_LOW;
+		of_gpio_quirk_polarity(np, active_high, flags);
 	}
 	/*
 	 * Legacy open drain handling for fixed voltage regulators.
@@ -200,18 +260,10 @@
 				 * conflict and the "spi-cs-high" flag will
 				 * take precedence.
 				 */
-				if (of_property_read_bool(child, "spi-cs-high")) {
-					if (*flags & OF_GPIO_ACTIVE_LOW) {
-						pr_warn("%s GPIO handle specifies active low - ignored\n",
-							of_node_full_name(child));
-						*flags &= ~OF_GPIO_ACTIVE_LOW;
-					}
-				} else {
-					if (!(*flags & OF_GPIO_ACTIVE_LOW))
-						pr_info("%s enforce active low on chipselect handle\n",
-							of_node_full_name(child));
-					*flags |= OF_GPIO_ACTIVE_LOW;
-				}
+				bool active_high = of_property_read_bool(child,
+								"spi-cs-high");
+				of_gpio_quirk_polarity(child, active_high,
+						       flags);
 				of_node_put(child);
 				break;
 			}
@@ -863,7 +915,8 @@
 	if (mm_gc->save_regs)
 		mm_gc->save_regs(mm_gc);
 
-	mm_gc->gc.of_node = np;
+	of_node_put(mm_gc->gc.of_node);
+	mm_gc->gc.of_node = of_node_get(np);
 
 	ret = gpiochip_add_data(gc, data);
 	if (ret)
@@ -871,6 +924,7 @@
 
 	return 0;
 err2:
+	of_node_put(np);
 	iounmap(mm_gc->regs);
 err1:
 	kfree(gc->label);
@@ -912,7 +966,7 @@
 					   i, &start);
 		of_property_read_u32_index(np, "gpio-reserved-ranges",
 					   i + 1, &count);
-		if (start >= chip->ngpio || start + count >= chip->ngpio)
+		if (start >= chip->ngpio || start + count > chip->ngpio)
 			continue;
 
 		bitmap_clear(chip->valid_mask, start, count);
@@ -933,6 +987,11 @@
 	if (!np)
 		return 0;
 
+	if (!of_property_read_bool(np, "gpio-ranges") &&
+	    chip->of_gpio_ranges_fallback) {
+		return chip->of_gpio_ranges_fallback(chip, np);
+	}
+
 	group_names = of_find_property(np, group_names_propname, NULL);
 
 	for (;; index++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpiolib-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpiolib-sysfs.c
@@ -475,22 +475,22 @@
 	 * they may be undone on its behalf too.
 	 */
 
-	status = gpiod_request(desc, "sysfs");
-	if (status) {
-		if (status == -EPROBE_DEFER)
-			status = -ENODEV;
+	status = gpiod_request_user(desc, "sysfs");
+	if (status)
 		goto done;
-	}
 
 	status = gpiod_set_transitory(desc, false);
-	if (!status) {
-		status = gpiod_export(desc, true);
-		if (status < 0)
-			gpiod_free(desc);
-		else
-			set_bit(FLAG_SYSFS, &desc->flags);
+	if (status) {
+		gpiod_free(desc);
+		goto done;
 	}
 
+	status = gpiod_export(desc, true);
+	if (status < 0)
+		gpiod_free(desc);
+	else
+		set_bit(FLAG_SYSFS, &desc->flags);
+
 done:
 	if (status)
 		pr_debug("%s: status %d\n", __func__, status);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpiolib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpiolib.c
@@ -5,6 +5,7 @@
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/nospec.h>
 #include <linux/spinlock.h>
 #include <linux/list.h>
 #include <linux/device.h>
@@ -146,7 +147,7 @@
 	if (hwnum >= gdev->ngpio)
 		return ERR_PTR(-EINVAL);
 
-	return &gdev->descs[hwnum];
+	return &gdev->descs[array_index_nospec(hwnum, gdev->ngpio)];
 }
 EXPORT_SYMBOL_GPL(gpiochip_get_desc);
 
@@ -189,9 +190,8 @@
 		/* found a free space? */
 		if (gdev->base + gdev->ngpio <= base)
 			break;
-		else
-			/* nope, check the space right before the chip */
-			base = gdev->base - ngpio;
+		/* nope, check the space right before the chip */
+		base = gdev->base - ngpio;
 	}
 
 	if (gpio_is_valid(base)) {
@@ -525,12 +525,13 @@
 	if (ret)
 		return ret;
 
+	/* From this point, the .release() function cleans up gpio_device */
+	gdev->dev.release = gpiodevice_release;
+
 	ret = gpiochip_sysfs_register(gdev);
 	if (ret)
 		goto err_remove_device;
 
-	/* From this point, the .release() function cleans up gpio_device */
-	gdev->dev.release = gpiodevice_release;
 	dev_dbg(&gdev->dev, "registered GPIOs %d to %d on %s\n", gdev->base,
 		gdev->base + gdev->ngpio - 1, gdev->chip->label ? : "generic");
 
@@ -594,11 +595,12 @@
 			       struct lock_class_key *request_key)
 {
 	struct fwnode_handle *fwnode = gc->parent ? dev_fwnode(gc->parent) : NULL;
-	unsigned long	flags;
-	int		ret = 0;
-	unsigned	i;
-	int		base = gc->base;
 	struct gpio_device *gdev;
+	unsigned long flags;
+	unsigned int i;
+	u32 ngpios = 0;
+	int base = 0;
+	int ret = 0;
 
 	/*
 	 * First: allocate and populate the internal stat container, and
@@ -640,22 +642,43 @@
 	else
 		gdev->owner = THIS_MODULE;
 
-	gdev->descs = kcalloc(gc->ngpio, sizeof(gdev->descs[0]), GFP_KERNEL);
-	if (!gdev->descs) {
-		ret = -ENOMEM;
-		goto err_free_dev_name;
+	/*
+	 * Try the device properties if the driver didn't supply the number
+	 * of GPIO lines.
+	 */
+	ngpios = gc->ngpio;
+	if (ngpios == 0) {
+		ret = device_property_read_u32(&gdev->dev, "ngpios", &ngpios);
+		if (ret == -ENODATA)
+			/*
+			 * -ENODATA means that there is no property found and
+			 * we want to issue the error message to the user.
+			 * Besides that, we want to return different error code
+			 * to state that supplied value is not valid.
+			 */
+			ngpios = 0;
+		else if (ret)
+			goto err_free_dev_name;
+
+		gc->ngpio = ngpios;
 	}
 
 	if (gc->ngpio == 0) {
 		chip_err(gc, "tried to insert a GPIO chip with zero lines\n");
 		ret = -EINVAL;
-		goto err_free_descs;
+		goto err_free_dev_name;
 	}
 
 	if (gc->ngpio > FASTPATH_NGPIO)
 		chip_warn(gc, "line cnt %u is greater than fast path cnt %u\n",
 			  gc->ngpio, FASTPATH_NGPIO);
 
+	gdev->descs = kcalloc(gc->ngpio, sizeof(*gdev->descs), GFP_KERNEL);
+	if (!gdev->descs) {
+		ret = -ENOMEM;
+		goto err_free_dev_name;
+	}
+
 	gdev->label = kstrdup_const(gc->label ?: "unknown", GFP_KERNEL);
 	if (!gdev->label) {
 		ret = -ENOMEM;
@@ -674,11 +697,13 @@
 	 * it may be a pipe dream. It will not happen before we get rid
 	 * of the sysfs interface anyways.
 	 */
+	base = gc->base;
 	if (base < 0) {
 		base = gpiochip_find_base(gc->ngpio);
 		if (base < 0) {
-			ret = base;
 			spin_unlock_irqrestore(&gpio_lock, flags);
+			ret = base;
+			base = 0;
 			goto err_free_label;
 		}
 		/*
@@ -703,6 +728,7 @@
 	spin_unlock_irqrestore(&gpio_lock, flags);
 
 	BLOCKING_INIT_NOTIFIER_HEAD(&gdev->notifier);
+	init_rwsem(&gdev->sem);
 
 #ifdef CONFIG_PINCTRL
 	INIT_LIST_HEAD(&gdev->pin_ranges);
@@ -749,11 +775,11 @@
 
 	ret = gpiochip_irqchip_init_valid_mask(gc);
 	if (ret)
-		goto err_remove_acpi_chip;
+		goto err_free_hogs;
 
 	ret = gpiochip_irqchip_init_hw(gc);
 	if (ret)
-		goto err_remove_acpi_chip;
+		goto err_remove_irqchip_mask;
 
 	ret = gpiochip_add_irqchip(gc, lock_key, request_key);
 	if (ret)
@@ -778,14 +804,19 @@
 	gpiochip_irqchip_remove(gc);
 err_remove_irqchip_mask:
 	gpiochip_irqchip_free_valid_mask(gc);
-err_remove_acpi_chip:
+err_free_hogs:
+	gpiochip_free_hogs(gc);
 	acpi_gpiochip_remove(gc);
+	gpiochip_remove_pin_ranges(gc);
 err_remove_of_chip:
-	gpiochip_free_hogs(gc);
 	of_gpiochip_remove(gc);
 err_free_gpiochip_mask:
-	gpiochip_remove_pin_ranges(gc);
 	gpiochip_free_valid_mask(gc);
+	if (gdev->dev.release) {
+		/* release() has been registered by gpiochip_setup_dev() */
+		put_device(&gdev->dev);
+		goto err_print_message;
+	}
 err_remove_from_list:
 	spin_lock_irqsave(&gpio_lock, flags);
 	list_del(&gdev->list);
@@ -799,13 +830,14 @@
 err_free_ida:
 	ida_free(&gpio_ida, gdev->id);
 err_free_gdev:
+	kfree(gdev);
+err_print_message:
 	/* failures here can mean systems won't boot... */
 	if (ret != -EPROBE_DEFER) {
 		pr_err("%s: GPIOs %d..%d (%s) failed to register, %d\n", __func__,
-		       gdev->base, gdev->base + gdev->ngpio - 1,
+		       base, base + (int)ngpios - 1,
 		       gc->label ? : "generic", ret);
 	}
-	kfree(gdev);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(gpiochip_add_data_with_key);
@@ -835,6 +867,8 @@
 	unsigned long	flags;
 	unsigned int	i;
 
+	down_write(&gdev->sem);
+
 	/* FIXME: should the legacy sysfs handling be moved to gpio_device? */
 	gpiochip_sysfs_unregister(gdev);
 	gpiochip_free_hogs(gc);
@@ -869,6 +903,7 @@
 	 * gone.
 	 */
 	gcdev_unregister(gdev);
+	up_write(&gdev->sem);
 	put_device(&gdev->dev);
 }
 EXPORT_SYMBOL_GPL(gpiochip_remove);
@@ -1368,6 +1403,16 @@
 {
 	struct irq_domain *domain = gc->irq.domain;
 
+#ifdef CONFIG_GPIOLIB_IRQCHIP
+	/*
+	 * Avoid race condition with other code, which tries to lookup
+	 * an IRQ before the irqchip has been properly registered,
+	 * i.e. while gpiochip is still being brought up.
+	 */
+	if (!gc->irq.initialized)
+		return -EPROBE_DEFER;
+#endif
+
 	if (!gpiochip_irqchip_irq_valid(gc, offset))
 		return -ENXIO;
 
@@ -1534,9 +1579,14 @@
 	}
 
 	if (gc->irq.parent_handler) {
-		void *data = gc->irq.parent_handler_data ?: gc;
-
 		for (i = 0; i < gc->irq.num_parents; i++) {
+			void *data;
+
+			if (gc->irq.per_parent_data)
+				data = gc->irq.parent_handler_data_array[i];
+			else
+				data = gc->irq.parent_handler_data ?: gc;
+
 			/*
 			 * The parent IRQ chip is already using the chip_data
 			 * for this IRQ chip, so our callbacks simply use the
@@ -1550,6 +1600,15 @@
 
 	gpiochip_set_irq_hooks(gc);
 
+	/*
+	 * Using barrier() here to prevent compiler from reordering
+	 * gc->irq.initialized before initialization of above
+	 * GPIO chip irq members.
+	 */
+	barrier();
+
+	gc->irq.initialized = true;
+
 	acpi_gpiochip_request_interrupts(gc);
 
 	return 0;
@@ -1625,6 +1684,14 @@
 	gc->to_irq = gpiochip_to_irq;
 	gc->irq.domain = domain;
 
+	/*
+	 * Using barrier() here to prevent compiler from reordering
+	 * gc->irq.initialized before adding irqdomain.
+	 */
+	barrier();
+
+	gc->irq.initialized = true;
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(gpiochip_irqchip_add_domain);
@@ -2186,6 +2253,16 @@
 	return gpio_set_config_with_argument_optional(desc, bias, arg);
 }
 
+/**
+ * gpio_set_debounce_timeout() - Set debounce timeout
+ * @desc:	GPIO descriptor to set the debounce timeout
+ * @debounce:	Debounce timeout in microseconds
+ *
+ * The function calls the certain GPIO driver to set debounce timeout
+ * in the hardware.
+ *
+ * Returns 0 on success, or negative error code otherwise.
+ */
 int gpio_set_debounce_timeout(struct gpio_desc *desc, unsigned int debounce)
 {
 	return gpio_set_config_with_argument_optional(desc,
@@ -2350,8 +2427,7 @@
 			ret = gpiod_direction_input(desc);
 			goto set_output_flag;
 		}
-	}
-	else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) {
+	} else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) {
 		ret = gpio_set_config(desc, PIN_CONFIG_DRIVE_OPEN_SOURCE);
 		if (!ret)
 			goto set_output_value;
@@ -2508,9 +2584,9 @@
 static int gpio_chip_get_multiple(struct gpio_chip *gc,
 				  unsigned long *mask, unsigned long *bits)
 {
-	if (gc->get_multiple) {
+	if (gc->get_multiple)
 		return gc->get_multiple(gc, mask, bits);
-	} else if (gc->get) {
+	if (gc->get) {
 		int i, value;
 
 		for_each_set_bit(i, mask, gc->ngpio) {
@@ -3106,6 +3182,16 @@
 
 		return retirq;
 	}
+#ifdef CONFIG_GPIOLIB_IRQCHIP
+	if (gc->irq.chip) {
+		/*
+		 * Avoid race condition with other code, which tries to lookup
+		 * an IRQ before the irqchip has been properly registered,
+		 * i.e. while gpiochip is still being brought up.
+		 */
+		return -EPROBE_DEFER;
+	}
+#endif
 	return -ENXIO;
 }
 EXPORT_SYMBOL_GPL(gpiod_to_irq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpio/gpiolib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpio/gpiolib.h
@@ -15,6 +15,7 @@
 #include <linux/device.h>
 #include <linux/module.h>
 #include <linux/cdev.h>
+#include <linux/rwsem.h>
 
 #define GPIOCHIP_NAME	"gpiochip"
 
@@ -37,6 +38,12 @@
  * or name of the IP component in a System on Chip.
  * @data: per-instance data assigned by the driver
  * @list: links gpio_device:s together for traversal
+ * @notifier: used to notify subscribers about lines being requested, released
+ *            or reconfigured
+ * @sem: protects the structure from a NULL-pointer dereference of @chip by
+ *       user-space operations when the device gets unregistered during
+ *       a hot-unplug event
+ * @pin_ranges: range of pins served by the GPIO driver
  *
  * This state container holds most of the runtime variable data
  * for a GPIO device and can hold references and live on after the
@@ -57,6 +64,7 @@
 	void			*data;
 	struct list_head        list;
 	struct blocking_notifier_head notifier;
+	struct rw_semaphore	sem;
 
 #ifdef CONFIG_PINCTRL
 	/*
@@ -72,6 +80,20 @@
 /* gpio suffixes used for ACPI and device tree lookup */
 static __maybe_unused const char * const gpio_suffixes[] = { "gpios", "gpio" };
 
+/**
+ * struct gpio_array - Opaque descriptor for a structure of GPIO array attributes
+ *
+ * @desc:		Array of pointers to the GPIO descriptors
+ * @size:		Number of elements in desc
+ * @chip:		Parent GPIO chip
+ * @get_mask:		Get mask used in fastpath
+ * @set_mask:		Set mask used in fastpath
+ * @invert_mask:	Invert mask used in fastpath
+ *
+ * This structure is attached to struct gpiod_descs obtained from
+ * gpiod_get_array() and can be passed back to get/set array functions in order
+ * to activate fast processing path if applicable.
+ */
 struct gpio_array {
 	struct gpio_desc	**desc;
 	unsigned int		size;
@@ -96,6 +118,23 @@
 extern spinlock_t gpio_lock;
 extern struct list_head gpio_devices;
 
+
+/**
+ * struct gpio_desc - Opaque descriptor for a GPIO
+ *
+ * @gdev:		Pointer to the parent GPIO device
+ * @flags:		Binary descriptor flags
+ * @label:		Name of the consumer
+ * @name:		Line name
+ * @hog:		Pointer to the device node that hogs this line (if any)
+ * @debounce_period_us:	Debounce period in microseconds
+ *
+ * These are obtained using gpiod_get() and are preferable to the old
+ * integer-based handles.
+ *
+ * Contrary to integers, a pointer to a &struct gpio_desc is guaranteed to be
+ * valid until the GPIO is released.
+ */
 struct gpio_desc {
 	struct gpio_device	*gdev;
 	unsigned long		flags;
@@ -135,6 +174,18 @@
 
 int gpiod_request(struct gpio_desc *desc, const char *label);
 void gpiod_free(struct gpio_desc *desc);
+
+static inline int gpiod_request_user(struct gpio_desc *desc, const char *label)
+{
+	int ret;
+
+	ret = gpiod_request(desc, label);
+	if (ret == -EPROBE_DEFER)
+		ret = -ENODEV;
+
+	return ret;
+}
+
 int gpiod_configure_flags(struct gpio_desc *desc, const char *con_id,
 		unsigned long lflags, enum gpiod_flags dflags);
 int gpio_set_debounce_timeout(struct gpio_desc *desc, unsigned int debounce);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/Kconfig
@@ -337,6 +337,8 @@
 
 source "drivers/gpu/drm/sti/Kconfig"
 
+source "drivers/gpu/drm/zocl/Kconfig"
+
 source "drivers/gpu/drm/imx/Kconfig"
 
 source "drivers/gpu/drm/ingenic/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/Makefile
@@ -103,6 +103,7 @@
 obj-$(CONFIG_DRM_TEGRA) += tegra/
 obj-$(CONFIG_DRM_STM) += stm/
 obj-$(CONFIG_DRM_STI) += sti/
+obj-$(CONFIG_DRM_ZOCL)  += zocl/
 obj-y 			+= imx/
 obj-$(CONFIG_DRM_INGENIC) += ingenic/
 obj-$(CONFIG_DRM_MEDIATEK) += mediatek/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/ObjectID.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/ObjectID.h
@@ -119,6 +119,7 @@
 #define CONNECTOR_OBJECT_ID_eDP                   0x14
 #define CONNECTOR_OBJECT_ID_MXM                   0x15
 #define CONNECTOR_OBJECT_ID_LVDS_eDP              0x16
+#define CONNECTOR_OBJECT_ID_USBC                  0x17
 
 /* deleted */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu.h
@@ -312,7 +312,7 @@
 	AMDGPU_CP_KIQ_IRQ_DRIVER0 = 0,
 	AMDGPU_CP_KIQ_IRQ_LAST
 };
-
+#define SRIOV_USEC_TIMEOUT  1200000 /* wait 12 * 100ms for SRIOV */
 #define MAX_KIQ_REG_WAIT       5000 /* in usecs, 5ms */
 #define MAX_KIQ_REG_BAILOUT_INTERVAL   5 /* in msecs, 5ms */
 #define MAX_KIQ_REG_TRY 1000
@@ -1045,6 +1045,8 @@
 	bool				in_s3;
 	bool				in_s4;
 	bool				in_s0ix;
+	/* indicate amdgpu suspension status */
+	bool				suspend_complete;
 
 	atomic_t 			in_gpu_reset;
 	enum pp_mp1_state               mp1_state;
@@ -1069,6 +1071,7 @@
 	bool                            runpm;
 	bool                            in_runpm;
 	bool                            has_pr3;
+	bool                            is_fw_fb;
 
 	bool                            pm_sysfs_en;
 	bool                            ucode_sysfs_en;
@@ -1078,8 +1081,6 @@
 	char				product_name[32];
 	char				serial[20];
 
-	struct amdgpu_autodump		autodump;
-
 	atomic_t			throttling_logging_enabled;
 	struct ratelimit_state		throttling_logging_rs;
 	uint32_t                        ras_hw_enabled;
@@ -1286,6 +1287,9 @@
 void amdgpu_device_pci_config_reset(struct amdgpu_device *adev);
 int amdgpu_device_pci_reset(struct amdgpu_device *adev);
 bool amdgpu_device_need_post(struct amdgpu_device *adev);
+bool amdgpu_device_pcie_dynamic_switching_supported(void);
+bool amdgpu_device_should_use_aspm(struct amdgpu_device *adev);
+bool amdgpu_device_aspm_support_quirk(void);
 
 void amdgpu_cs_report_moved_bytes(struct amdgpu_device *adev, u64 num_bytes,
 				  u64 num_vis_bytes);
@@ -1398,12 +1402,10 @@
 int amdgpu_acpi_pcie_notify_device_ready(struct amdgpu_device *adev);
 
 void amdgpu_acpi_get_backlight_caps(struct amdgpu_dm_backlight_caps *caps);
-bool amdgpu_acpi_is_s0ix_active(struct amdgpu_device *adev);
 void amdgpu_acpi_detect(void);
 #else
 static inline int amdgpu_acpi_init(struct amdgpu_device *adev) { return 0; }
 static inline void amdgpu_acpi_fini(struct amdgpu_device *adev) { }
-static inline bool amdgpu_acpi_is_s0ix_active(struct amdgpu_device *adev) { return false; }
 static inline void amdgpu_acpi_detect(void) { }
 static inline bool amdgpu_acpi_is_power_shift_control_supported(void) { return false; }
 static inline int amdgpu_acpi_power_shift_control(struct amdgpu_device *adev,
@@ -1412,6 +1414,16 @@
 						 enum amdgpu_ss ss_state) { return 0; }
 #endif
 
+#if defined(CONFIG_ACPI) && defined(CONFIG_SUSPEND)
+bool amdgpu_acpi_is_s3_active(struct amdgpu_device *adev);
+bool amdgpu_acpi_should_gpu_reset(struct amdgpu_device *adev);
+bool amdgpu_acpi_is_s0ix_active(struct amdgpu_device *adev);
+#else
+static inline bool amdgpu_acpi_is_s0ix_active(struct amdgpu_device *adev) { return false; }
+static inline bool amdgpu_acpi_should_gpu_reset(struct amdgpu_device *adev) { return false; }
+static inline bool amdgpu_acpi_is_s3_active(struct amdgpu_device *adev) { return false; }
+#endif
+
 int amdgpu_cs_find_mapping(struct amdgpu_cs_parser *parser,
 			   uint64_t addr, struct amdgpu_bo **bo,
 			   struct amdgpu_bo_va_mapping **mapping);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c
@@ -108,6 +108,7 @@
 					   struct acpi_buffer *params)
 {
 	acpi_status status;
+	union acpi_object *obj;
 	union acpi_object atif_arg_elements[2];
 	struct acpi_object_list atif_arg;
 	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
@@ -130,16 +131,24 @@
 
 	status = acpi_evaluate_object(atif->handle, NULL, &atif_arg,
 				      &buffer);
+	obj = (union acpi_object *)buffer.pointer;
 
-	/* Fail only if calling the method fails and ATIF is supported */
-	if (ACPI_FAILURE(status) && status != AE_NOT_FOUND) {
+	/* Fail if calling the method fails */
+	if (ACPI_FAILURE(status)) {
 		DRM_DEBUG_DRIVER("failed to evaluate ATIF got %s\n",
 				 acpi_format_exception(status));
-		kfree(buffer.pointer);
+		kfree(obj);
 		return NULL;
 	}
 
-	return buffer.pointer;
+	if (obj->type != ACPI_TYPE_BUFFER) {
+		DRM_DEBUG_DRIVER("bad object returned from ATIF: %d\n",
+				 obj->type);
+		kfree(obj);
+		return NULL;
+	}
+
+	return obj;
 }
 
 /**
@@ -752,6 +761,7 @@
 		return -EIO;
 	}
 
+	kfree(info);
 	return 0;
 }
 
@@ -1031,6 +1041,38 @@
 	}
 }
 
+#if IS_ENABLED(CONFIG_SUSPEND)
+/**
+ * amdgpu_acpi_is_s3_active
+ *
+ * @adev: amdgpu_device_pointer
+ *
+ * returns true if supported, false if not.
+ */
+bool amdgpu_acpi_is_s3_active(struct amdgpu_device *adev)
+{
+	return !(adev->flags & AMD_IS_APU) ||
+		(pm_suspend_target_state == PM_SUSPEND_MEM);
+}
+
+/**
+ * amdgpu_acpi_should_gpu_reset
+ *
+ * @adev: amdgpu_device_pointer
+ *
+ * returns true if should reset GPU, false if not
+ */
+bool amdgpu_acpi_should_gpu_reset(struct amdgpu_device *adev)
+{
+	if (adev->flags & AMD_IS_APU)
+		return false;
+
+	if (amdgpu_sriov_vf(adev))
+		return false;
+
+	return pm_suspend_target_state != PM_SUSPEND_TO_IDLE;
+}
+
 /**
  * amdgpu_acpi_is_s0ix_active
  *
@@ -1040,11 +1082,24 @@
  */
 bool amdgpu_acpi_is_s0ix_active(struct amdgpu_device *adev)
 {
-#if IS_ENABLED(CONFIG_AMD_PMC) && IS_ENABLED(CONFIG_SUSPEND)
-	if (acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0) {
-		if (adev->flags & AMD_IS_APU)
-			return pm_suspend_target_state == PM_SUSPEND_TO_IDLE;
+	if (!(adev->flags & AMD_IS_APU) ||
+	    (pm_suspend_target_state != PM_SUSPEND_TO_IDLE))
+		return false;
+
+	if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0)) {
+		dev_warn_once(adev->dev,
+			      "Power consumption will be higher as BIOS has not been configured for suspend-to-idle.\n"
+			      "To use suspend-to-idle change the sleep mode in BIOS setup.\n");
+		return false;
 	}
-#endif
+
+#if !IS_ENABLED(CONFIG_AMD_PMC)
+	dev_warn_once(adev->dev,
+		      "Power consumption will be higher as the kernel has not been compiled with CONFIG_AMD_PMC.\n");
 	return false;
+#else
+	return true;
+#endif /* CONFIG_AMD_PMC */
 }
+
+#endif /* CONFIG_SUSPEND */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_afmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_afmt.c
@@ -100,6 +100,7 @@
 	amdgpu_afmt_calc_cts(clock, &res.cts_32khz, &res.n_32khz, 32000);
 	amdgpu_afmt_calc_cts(clock, &res.cts_44_1khz, &res.n_44_1khz, 44100);
 	amdgpu_afmt_calc_cts(clock, &res.cts_48khz, &res.n_48khz, 48000);
+	res.clock = clock;
 
 	return res;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.c
@@ -768,7 +768,8 @@
 	struct amdgpu_device *adev = (struct amdgpu_device *)kgd;
 	bool all_hub = false;
 
-	if (adev->family == AMDGPU_FAMILY_AI)
+	if (adev->family == AMDGPU_FAMILY_AI ||
+	    adev->family == AMDGPU_FAMILY_RV)
 		all_hub = true;
 
 	return amdgpu_gmc_flush_gpu_tlb_pasid(adev, pasid, flush_type, all_hub);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_aldebaran.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_aldebaran.c
@@ -44,5 +44,6 @@
 	.get_atc_vmid_pasid_mapping_info =
 				kgd_gfx_v9_get_atc_vmid_pasid_mapping_info,
 	.set_vm_context_page_table_base = kgd_gfx_v9_set_vm_context_page_table_base,
+	.get_cu_occupancy = kgd_gfx_v9_get_cu_occupancy,
 	.program_trap_handler_settings = kgd_gfx_v9_program_trap_handler_settings
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_fence.c
@@ -90,7 +90,7 @@
 		return NULL;
 
 	fence = container_of(f, struct amdgpu_amdkfd_fence, base);
-	if (fence && f->ops == &amdkfd_fence_ops)
+	if (f->ops == &amdkfd_fence_ops)
 		return fence;
 
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gpuvm.c
@@ -476,13 +476,13 @@
 	struct ttm_tt *ttm = bo->tbo.ttm;
 	int ret;
 
+	if (WARN_ON(ttm->num_pages != src_ttm->num_pages))
+		return -EINVAL;
+
 	ttm->sg = kmalloc(sizeof(*ttm->sg), GFP_KERNEL);
 	if (unlikely(!ttm->sg))
 		return -ENOMEM;
 
-	if (WARN_ON(ttm->num_pages != src_ttm->num_pages))
-		return -EINVAL;
-
 	/* Same sequence as in amdgpu_ttm_tt_pin_userptr */
 	ret = sg_alloc_table_from_pages(ttm->sg, src_ttm->pages,
 					ttm->num_pages, 0,
@@ -1318,16 +1318,10 @@
 				    struct amdgpu_vm *vm)
 {
 	struct amdkfd_process_info *process_info = vm->process_info;
-	struct amdgpu_bo *pd = vm->root.bo;
 
 	if (!process_info)
 		return;
 
-	/* Release eviction fence from PD */
-	amdgpu_bo_reserve(pd, false);
-	amdgpu_bo_fence(pd, NULL, false);
-	amdgpu_bo_unreserve(pd);
-
 	/* Update process info */
 	mutex_lock(&process_info->lock);
 	process_info->n_vms--;
@@ -1393,7 +1387,7 @@
 	struct sg_table *sg = NULL;
 	uint64_t user_addr = 0;
 	struct amdgpu_bo *bo;
-	struct drm_gem_object *gobj;
+	struct drm_gem_object *gobj = NULL;
 	u32 domain, alloc_domain;
 	u64 alloc_flags;
 	int ret;
@@ -1503,14 +1497,17 @@
 	remove_kgd_mem_from_kfd_bo_list(*mem, avm->process_info);
 	drm_vma_node_revoke(&gobj->vma_node, drm_priv);
 err_node_allow:
-	amdgpu_bo_unref(&bo);
 	/* Don't unreserve system mem limit twice */
 	goto err_reserve_limit;
 err_bo_create:
 	unreserve_mem_limit(adev, size, alloc_domain, !!sg);
 err_reserve_limit:
+	amdgpu_sync_free(&(*mem)->sync);
 	mutex_destroy(&(*mem)->lock);
-	kfree(*mem);
+	if (gobj)
+		drm_gem_object_put(gobj);
+	else
+		kfree(*mem);
 err:
 	if (sg) {
 		sg_free_table(sg);
@@ -1826,9 +1823,6 @@
 		return -EINVAL;
 	}
 
-	/* delete kgd_mem from kfd_bo_list to avoid re-validating
-	 * this BO in BO's restoring after eviction.
-	 */
 	mutex_lock(&mem->process_info->lock);
 
 	ret = amdgpu_bo_reserve(bo, true);
@@ -1851,7 +1845,6 @@
 
 	amdgpu_amdkfd_remove_eviction_fence(
 		bo, mem->process_info->eviction_fence);
-	list_del_init(&mem->validate_list.head);
 
 	if (size)
 		*size = amdgpu_bo_size(bo);
@@ -1918,7 +1911,7 @@
 
 	ret = drm_vma_node_allow(&obj->vma_node, drm_priv);
 	if (ret) {
-		kfree(mem);
+		kfree(*mem);
 		return ret;
 	}
 
@@ -2358,6 +2351,9 @@
 			if (!attachment->is_mapped)
 				continue;
 
+			if (attachment->bo_va->base.bo->tbo.pin_count)
+				continue;
+
 			kfd_mem_dmaunmap_attachment(mem, attachment);
 			ret = update_gpuvm_pte(mem, attachment, &sync_obj, NULL);
 			if (ret) {
@@ -2397,12 +2393,15 @@
 	process_info->eviction_fence = new_fence;
 	*ef = dma_fence_get(&new_fence->base);
 
-	/* Attach new eviction fence to all BOs */
+	/* Attach new eviction fence to all BOs except pinned ones */
 	list_for_each_entry(mem, &process_info->kfd_bo_list,
-		validate_list.head)
+		validate_list.head) {
+		if (mem->bo->tbo.pin_count)
+			continue;
+
 		amdgpu_bo_fence(mem->bo,
 			&process_info->eviction_fence->base, true);
-
+	}
 	/* Attach eviction fence to PD / PT BOs */
 	list_for_each_entry(peer_vm, &process_info->vm_list_head,
 			    vm_list_node) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c
@@ -1475,6 +1475,8 @@
 										(u32)le32_to_cpu(*((u32 *)reg_data + j));
 									j++;
 								} else if ((reg_table->mc_reg_address[i].pre_reg_data & LOW_NIBBLE_MASK) == DATA_EQU_PREV) {
+									if (i == 0)
+										continue;
 									reg_table->mc_reg_table_entry[num_ranges].mc_data[i] =
 										reg_table->mc_reg_table_entry[num_ranges].mc_data[i - 1];
 								}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_atomfirmware.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_atomfirmware.c
@@ -149,6 +149,7 @@
 	struct atom_integrated_system_info_v1_11 v11;
 	struct atom_integrated_system_info_v1_12 v12;
 	struct atom_integrated_system_info_v2_1 v21;
+	struct atom_integrated_system_info_v2_3 v23;
 };
 
 union umc_info {
@@ -283,6 +284,20 @@
 					if (vram_type)
 						*vram_type = convert_atom_mem_type_to_vram_type(adev, mem_type);
 					break;
+				case 3:
+					mem_channel_number = igp_info->v23.umachannelnumber;
+					if (!mem_channel_number)
+						mem_channel_number = 1;
+					mem_type = igp_info->v23.memorytype;
+					if (mem_type == LpDdr5MemType)
+						mem_channel_width = 32;
+					else
+						mem_channel_width = 64;
+					if (vram_width)
+						*vram_width = mem_channel_number * mem_channel_width;
+					if (vram_type)
+						*vram_type = convert_atom_mem_type_to_vram_type(adev, mem_type);
+					break;
 				default:
 					return -EINVAL;
 				}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_bios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_bios.c
@@ -29,6 +29,7 @@
 #include "amdgpu.h"
 #include "atom.h"
 
+#include <linux/device.h>
 #include <linux/pci.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
@@ -289,6 +290,10 @@
 	if (adev->flags & AMD_IS_APU)
 		return false;
 
+	/* ATRM is for on-platform devices only */
+	if (dev_is_removable(&adev->pdev->dev))
+		return false;
+
 	while ((pdev = pci_get_class(PCI_CLASS_DISPLAY_VGA << 8, pdev)) != NULL) {
 		dhandle = ACPI_HANDLE(&pdev->dev);
 		if (!dhandle)
@@ -317,6 +322,7 @@
 
 	if (!found)
 		return false;
+	pci_dev_put(pdev);
 
 	adev->bios = kmalloc(size, GFP_KERNEL);
 	if (!adev->bios) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c
@@ -61,7 +61,7 @@
 
 int amdgpu_bo_list_create(struct amdgpu_device *adev, struct drm_file *filp,
 			  struct drm_amdgpu_bo_list_entry *info,
-			  unsigned num_entries, struct amdgpu_bo_list **result)
+			  size_t num_entries, struct amdgpu_bo_list **result)
 {
 	unsigned last_entry = 0, first_userptr = num_entries;
 	struct amdgpu_bo_list_entry *array;
@@ -178,6 +178,7 @@
 	}
 
 	rcu_read_unlock();
+	*result = NULL;
 	return -ENOENT;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.h
@@ -61,7 +61,7 @@
 int amdgpu_bo_list_create(struct amdgpu_device *adev,
 				 struct drm_file *filp,
 				 struct drm_amdgpu_bo_list_entry *info,
-				 unsigned num_entries,
+				 size_t num_entries,
 				 struct amdgpu_bo_list **list);
 
 static inline struct amdgpu_bo_list_entry *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c
@@ -213,6 +213,9 @@
 		struct amdgpu_firmware_info *ucode;
 
 		id = fw_type_convert(cgs_device, type);
+		if (id >= AMDGPU_UCODE_ID_MAXIMUM)
+			return -EINVAL;
+
 		ucode = &adev->firmware.ucode[id];
 		if (ucode->fw == NULL)
 			return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_connectors.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_connectors.c
@@ -175,7 +175,7 @@
 
 			/* Check if bpc is within clock limit. Try to degrade gracefully otherwise */
 			if ((bpc == 12) && (mode_clock * 3/2 > max_tmds_clock)) {
-				if ((connector->display_info.edid_hdmi_dc_modes & DRM_EDID_HDMI_DC_30) &&
+				if ((connector->display_info.edid_hdmi_rgb444_dc_modes & DRM_EDID_HDMI_DC_30) &&
 				    (mode_clock * 5/4 <= max_tmds_clock))
 					bpc = 10;
 				else
@@ -315,8 +315,10 @@
 	if (!amdgpu_connector->edid) {
 		/* some laptops provide a hardcoded edid in rom for LCDs */
 		if (((connector->connector_type == DRM_MODE_CONNECTOR_LVDS) ||
-		     (connector->connector_type == DRM_MODE_CONNECTOR_eDP)))
+		     (connector->connector_type == DRM_MODE_CONNECTOR_eDP))) {
 			amdgpu_connector->edid = amdgpu_connector_get_hardcoded_edid(adev);
+			drm_connector_update_edid_property(connector, amdgpu_connector->edid);
+		}
 	}
 }
 
@@ -387,6 +389,9 @@
 	    native_mode->vdisplay != 0 &&
 	    native_mode->clock != 0) {
 		mode = drm_mode_duplicate(dev, native_mode);
+		if (!mode)
+			return NULL;
+
 		mode->type = DRM_MODE_TYPE_PREFERRED | DRM_MODE_TYPE_DRIVER;
 		drm_mode_set_name(mode);
 
@@ -401,6 +406,9 @@
 		 * simpler.
 		 */
 		mode = drm_cvt_mode(dev, native_mode->hdisplay, native_mode->vdisplay, 60, true, false, false);
+		if (!mode)
+			return NULL;
+
 		mode->type = DRM_MODE_TYPE_PREFERRED | DRM_MODE_TYPE_DRIVER;
 		DRM_DEBUG_KMS("Adding cvt approximation of native panel mode %s\n", mode->name);
 	}
@@ -617,7 +625,7 @@
 		if (mode->type & DRM_MODE_TYPE_PREFERRED) {
 			if (mode->hdisplay != native_mode->hdisplay ||
 			    mode->vdisplay != native_mode->vdisplay)
-				memcpy(native_mode, mode, sizeof(*mode));
+				drm_mode_copy(native_mode, mode);
 		}
 	}
 
@@ -626,7 +634,7 @@
 		list_for_each_entry_safe(mode, t, &connector->probed_modes, head) {
 			if (mode->hdisplay == native_mode->hdisplay &&
 			    mode->vdisplay == native_mode->vdisplay) {
-				*native_mode = *mode;
+				drm_mode_copy(native_mode, mode);
 				drm_mode_set_crtcinfo(native_mode, CRTC_INTERLACE_HALVE_V);
 				DRM_DEBUG_KMS("Determined LVDS native mode details from EDID\n");
 				break;
@@ -827,6 +835,7 @@
 
 	amdgpu_connector_get_edid(connector);
 	ret = amdgpu_connector_ddc_get_modes(connector);
+	amdgpu_get_native_mode(connector);
 
 	return ret;
 }
@@ -1664,10 +1673,12 @@
 						   adev->mode_info.dither_property,
 						   AMDGPU_FMT_DITHER_DISABLE);
 
-			if (amdgpu_audio != 0)
+			if (amdgpu_audio != 0) {
 				drm_object_attach_property(&amdgpu_connector->base.base,
 							   adev->mode_info.audio_property,
 							   AMDGPU_AUDIO_AUTO);
+				amdgpu_connector->audio = AMDGPU_AUDIO_AUTO;
+			}
 
 			subpixel_order = SubPixelHorizontalRGB;
 			connector->interlace_allowed = true;
@@ -1789,6 +1800,7 @@
 				drm_object_attach_property(&amdgpu_connector->base.base,
 							   adev->mode_info.audio_property,
 							   AMDGPU_AUDIO_AUTO);
+				amdgpu_connector->audio = AMDGPU_AUDIO_AUTO;
 			}
 			drm_object_attach_property(&amdgpu_connector->base.base,
 						   adev->mode_info.dither_property,
@@ -1842,6 +1854,7 @@
 				drm_object_attach_property(&amdgpu_connector->base.base,
 							   adev->mode_info.audio_property,
 							   AMDGPU_AUDIO_AUTO);
+				amdgpu_connector->audio = AMDGPU_AUDIO_AUTO;
 			}
 			drm_object_attach_property(&amdgpu_connector->base.base,
 						   adev->mode_info.dither_property,
@@ -1892,6 +1905,7 @@
 				drm_object_attach_property(&amdgpu_connector->base.base,
 							   adev->mode_info.audio_property,
 							   AMDGPU_AUDIO_AUTO);
+				amdgpu_connector->audio = AMDGPU_AUDIO_AUTO;
 			}
 			drm_object_attach_property(&amdgpu_connector->base.base,
 						   adev->mode_info.dither_property,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_cs.c
@@ -45,7 +45,6 @@
 	struct drm_gem_object *gobj;
 	struct amdgpu_bo *bo;
 	unsigned long size;
-	int r;
 
 	gobj = drm_gem_object_lookup(p->filp, data->handle);
 	if (gobj == NULL)
@@ -60,23 +59,14 @@
 	drm_gem_object_put(gobj);
 
 	size = amdgpu_bo_size(bo);
-	if (size != PAGE_SIZE || (data->offset + 8) > size) {
-		r = -EINVAL;
-		goto error_unref;
-	}
+	if (size != PAGE_SIZE || data->offset > (size - 8))
+		return -EINVAL;
 
-	if (amdgpu_ttm_tt_get_usermm(bo->tbo.ttm)) {
-		r = -EINVAL;
-		goto error_unref;
-	}
+	if (amdgpu_ttm_tt_get_usermm(bo->tbo.ttm))
+		return -EINVAL;
 
 	*offset = data->offset;
-
 	return 0;
-
-error_unref:
-	amdgpu_bo_unref(&bo);
-	return r;
 }
 
 static int amdgpu_cs_bo_handles_chunk(struct amdgpu_cs_parser *p,
@@ -115,7 +105,7 @@
 	int ret;
 
 	if (cs->in.num_chunks == 0)
-		return 0;
+		return -EINVAL;
 
 	chunk_array = kvmalloc_array(cs->in.num_chunks, sizeof(uint64_t), GFP_KERNEL);
 	if (!chunk_array)
@@ -152,7 +142,7 @@
 	}
 
 	for (i = 0; i < p->nchunks; i++) {
-		struct drm_amdgpu_cs_chunk __user **chunk_ptr = NULL;
+		struct drm_amdgpu_cs_chunk __user *chunk_ptr = NULL;
 		struct drm_amdgpu_cs_chunk user_chunk;
 		uint32_t __user *cdata;
 
@@ -1508,6 +1498,7 @@
 		return 0;
 
 	default:
+		dma_fence_put(fence);
 		return -EINVAL;
 	}
 }
@@ -1540,15 +1531,15 @@
 			continue;
 
 		r = dma_fence_wait_timeout(fence, true, timeout);
+		if (r > 0 && fence->error)
+			r = fence->error;
+
 		dma_fence_put(fence);
 		if (r < 0)
 			return r;
 
 		if (r == 0)
 			break;
-
-		if (fence->error)
-			return fence->error;
 	}
 
 	memset(wait, 0, sizeof(*wait));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ctx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ctx.c
@@ -413,16 +413,24 @@
 
 	switch (args->in.op) {
 	case AMDGPU_CTX_OP_ALLOC_CTX:
+		if (args->in.flags)
+			return -EINVAL;
 		r = amdgpu_ctx_alloc(adev, fpriv, filp, priority, &id);
 		args->out.alloc.ctx_id = id;
 		break;
 	case AMDGPU_CTX_OP_FREE_CTX:
+		if (args->in.flags)
+			return -EINVAL;
 		r = amdgpu_ctx_free(fpriv, id);
 		break;
 	case AMDGPU_CTX_OP_QUERY_STATE:
+		if (args->in.flags)
+			return -EINVAL;
 		r = amdgpu_ctx_query(adev, fpriv, id, &args->out);
 		break;
 	case AMDGPU_CTX_OP_QUERY_STATE2:
+		if (args->in.flags)
+			return -EINVAL;
 		r = amdgpu_ctx_query2(adev, fpriv, id, &args->out);
 		break;
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c
@@ -27,7 +27,6 @@
 #include <linux/pci.h>
 #include <linux/uaccess.h>
 #include <linux/pm_runtime.h>
-#include <linux/poll.h>
 
 #include "amdgpu.h"
 #include "amdgpu_pm.h"
@@ -37,86 +36,8 @@
 #include "amdgpu_securedisplay.h"
 #include "amdgpu_fw_attestation.h"
 
-int amdgpu_debugfs_wait_dump(struct amdgpu_device *adev)
-{
-#if defined(CONFIG_DEBUG_FS)
-	unsigned long timeout = 600 * HZ;
-	int ret;
-
-	wake_up_interruptible(&adev->autodump.gpu_hang);
-
-	ret = wait_for_completion_interruptible_timeout(&adev->autodump.dumping, timeout);
-	if (ret == 0) {
-		pr_err("autodump: timeout, move on to gpu recovery\n");
-		return -ETIMEDOUT;
-	}
-#endif
-	return 0;
-}
-
 #if defined(CONFIG_DEBUG_FS)
 
-static int amdgpu_debugfs_autodump_open(struct inode *inode, struct file *file)
-{
-	struct amdgpu_device *adev = inode->i_private;
-	int ret;
-
-	file->private_data = adev;
-
-	ret = down_read_killable(&adev->reset_sem);
-	if (ret)
-		return ret;
-
-	if (adev->autodump.dumping.done) {
-		reinit_completion(&adev->autodump.dumping);
-		ret = 0;
-	} else {
-		ret = -EBUSY;
-	}
-
-	up_read(&adev->reset_sem);
-
-	return ret;
-}
-
-static int amdgpu_debugfs_autodump_release(struct inode *inode, struct file *file)
-{
-	struct amdgpu_device *adev = file->private_data;
-
-	complete_all(&adev->autodump.dumping);
-	return 0;
-}
-
-static unsigned int amdgpu_debugfs_autodump_poll(struct file *file, struct poll_table_struct *poll_table)
-{
-	struct amdgpu_device *adev = file->private_data;
-
-	poll_wait(file, &adev->autodump.gpu_hang, poll_table);
-
-	if (amdgpu_in_reset(adev))
-		return POLLIN | POLLRDNORM | POLLWRNORM;
-
-	return 0;
-}
-
-static const struct file_operations autodump_debug_fops = {
-	.owner = THIS_MODULE,
-	.open = amdgpu_debugfs_autodump_open,
-	.poll = amdgpu_debugfs_autodump_poll,
-	.release = amdgpu_debugfs_autodump_release,
-};
-
-static void amdgpu_debugfs_autodump_init(struct amdgpu_device *adev)
-{
-	init_completion(&adev->autodump.dumping);
-	complete_all(&adev->autodump.dumping);
-	init_waitqueue_head(&adev->autodump.gpu_hang);
-
-	debugfs_create_file("amdgpu_autodump", 0600,
-		adev_to_drm(adev)->primary->debugfs_root,
-		adev, &autodump_debug_fops);
-}
-
 /**
  * amdgpu_debugfs_process_reg_op - Handle MMIO register reads/writes
  *
@@ -421,6 +342,9 @@
 	if (size & 0x3 || *pos & 0x3)
 		return -EINVAL;
 
+	if (!adev->didt_rreg)
+		return -EOPNOTSUPP;
+
 	r = pm_runtime_get_sync(adev_to_drm(adev)->dev);
 	if (r < 0) {
 		pm_runtime_put_autosuspend(adev_to_drm(adev)->dev);
@@ -480,6 +404,9 @@
 	if (size & 0x3 || *pos & 0x3)
 		return -EINVAL;
 
+	if (!adev->didt_wreg)
+		return -EOPNOTSUPP;
+
 	r = pm_runtime_get_sync(adev_to_drm(adev)->dev);
 	if (r < 0) {
 		pm_runtime_put_autosuspend(adev_to_drm(adev)->dev);
@@ -537,6 +464,9 @@
 	ssize_t result = 0;
 	int r;
 
+	if (!adev->smc_rreg)
+		return -EOPNOTSUPP;
+
 	if (size & 0x3 || *pos & 0x3)
 		return -EINVAL;
 
@@ -596,6 +526,9 @@
 	ssize_t result = 0;
 	int r;
 
+	if (!adev->smc_wreg)
+		return -EOPNOTSUPP;
+
 	if (size & 0x3 || *pos & 0x3)
 		return -EINVAL;
 
@@ -1255,7 +1188,7 @@
 		return r;
 	}
 
-	*val = amdgpu_bo_evict_vram(adev);
+	*val = amdgpu_ttm_evict_resources(adev, TTM_PL_VRAM);
 
 	pm_runtime_mark_last_busy(dev->dev);
 	pm_runtime_put_autosuspend(dev->dev);
@@ -1268,17 +1201,15 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)data;
 	struct drm_device *dev = adev_to_drm(adev);
-	struct ttm_resource_manager *man;
 	int r;
 
 	r = pm_runtime_get_sync(dev->dev);
 	if (r < 0) {
-		pm_runtime_put_autosuspend(adev_to_drm(adev)->dev);
+		pm_runtime_put_autosuspend(dev->dev);
 		return r;
 	}
 
-	man = ttm_manager_type(&adev->mman.bdev, TTM_PL_TT);
-	*val = ttm_resource_manager_evict_all(&adev->mman.bdev, man);
+	*val = amdgpu_ttm_evict_resources(adev, TTM_PL_TT);
 
 	pm_runtime_mark_last_busy(dev->dev);
 	pm_runtime_put_autosuspend(dev->dev);
@@ -1588,16 +1519,15 @@
 	}
 
 	amdgpu_ras_debugfs_create_all(adev);
-	amdgpu_debugfs_autodump_init(adev);
 	amdgpu_rap_debugfs_init(adev);
 	amdgpu_securedisplay_debugfs_init(adev);
 	amdgpu_fw_attestation_debugfs_init(adev);
 
-	debugfs_create_file("amdgpu_evict_vram", 0444, root, adev,
+	debugfs_create_file("amdgpu_evict_vram", 0400, root, adev,
 			    &amdgpu_evict_vram_fops);
-	debugfs_create_file("amdgpu_evict_gtt", 0444, root, adev,
+	debugfs_create_file("amdgpu_evict_gtt", 0400, root, adev,
 			    &amdgpu_evict_gtt_fops);
-	debugfs_create_file("amdgpu_test_ib", 0444, root, adev,
+	debugfs_create_file("amdgpu_test_ib", 0400, root, adev,
 			    &amdgpu_debugfs_test_ib_fops);
 	debugfs_create_file("amdgpu_vm_info", 0444, root, adev,
 			    &amdgpu_debugfs_vm_info_fops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.h
@@ -26,10 +26,6 @@
 /*
  * Debugfs
  */
-struct amdgpu_autodump {
-	struct completion		dumping;
-	struct wait_queue_head		gpu_hang;
-};
 
 int amdgpu_debugfs_regs_init(struct amdgpu_device *adev);
 int amdgpu_debugfs_init(struct amdgpu_device *adev);
@@ -37,4 +33,3 @@
 void amdgpu_debugfs_fence_init(struct amdgpu_device *adev);
 void amdgpu_debugfs_firmware_init(struct amdgpu_device *adev);
 void amdgpu_debugfs_gem_init(struct amdgpu_device *adev);
-int amdgpu_debugfs_wait_dump(struct amdgpu_device *adev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_device.c
@@ -30,7 +30,9 @@
 #include <linux/module.h>
 #include <linux/console.h>
 #include <linux/slab.h>
+#include <linux/pci.h>
 
+#include <drm/drm_aperture.h>
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_probe_helper.h>
 #include <drm/amdgpu_drm.h>
@@ -73,6 +75,10 @@
 
 #include <drm/drm_drv.h>
 
+#if IS_ENABLED(CONFIG_X86)
+#include <asm/intel-family.h>
+#endif
+
 MODULE_FIRMWARE("amdgpu/vega10_gpu_info.bin");
 MODULE_FIRMWARE("amdgpu/vega12_gpu_info.bin");
 MODULE_FIRMWARE("amdgpu/raven_gpu_info.bin");
@@ -88,6 +94,8 @@
 
 #define AMDGPU_RESUME_MS		2000
 
+static const struct drm_driver amdgpu_kms_driver;
+
 const char *amdgpu_asic_name[] = {
 	"TAHITI",
 	"PITCAIRN",
@@ -1187,10 +1195,24 @@
 	u16 cmd;
 	int r;
 
+	if (!IS_ENABLED(CONFIG_PHYS_ADDR_T_64BIT))
+		return 0;
+
 	/* Bypass for VF */
 	if (amdgpu_sriov_vf(adev))
 		return 0;
 
+	/* resizing on Dell G5 SE platforms causes problems with runtime pm */
+	if ((amdgpu_runtime_pm != 0) &&
+	    adev->pdev->vendor == PCI_VENDOR_ID_ATI &&
+	    adev->pdev->device == 0x731f &&
+	    adev->pdev->subsystem_vendor == PCI_VENDOR_ID_DELL)
+		return 0;
+
+	/* PCI_EXT_CAP_ID_VNDR extended capability is located at 0x100 */
+	if (!pci_find_ext_capability(adev->pdev, PCI_EXT_CAP_ID_VNDR))
+		DRM_WARN("System can't access extended configuration space,please check!!\n");
+
 	/* skip if the bios has already enabled large BAR */
 	if (adev->gmc.real_vram_size &&
 	    (pci_resource_len(adev->pdev, 0) >= adev->gmc.real_vram_size))
@@ -1281,6 +1303,7 @@
 				return true;
 
 			fw_ver = *((uint32_t *)adev->pm.fw->data + 69);
+			release_firmware(adev->pm.fw);
 			if (fw_ver < 0x00160e00)
 				return true;
 		}
@@ -1308,6 +1331,61 @@
 	return true;
 }
 
+/*
+ * Intel hosts such as Raptor Lake and Sapphire Rapids don't support dynamic
+ * speed switching. Until we have confirmation from Intel that a specific host
+ * supports it, it's safer that we keep it disabled for all.
+ *
+ * https://edc.intel.com/content/www/us/en/design/products/platforms/details/raptor-lake-s/13th-generation-core-processors-datasheet-volume-1-of-2/005/pci-express-support/
+ * https://gitlab.freedesktop.org/drm/amd/-/issues/2663
+ */
+bool amdgpu_device_pcie_dynamic_switching_supported(void)
+{
+#if IS_ENABLED(CONFIG_X86)
+	struct cpuinfo_x86 *c = &cpu_data(0);
+
+	if (c->x86_vendor == X86_VENDOR_INTEL)
+		return false;
+#endif
+	return true;
+}
+
+/**
+ * amdgpu_device_should_use_aspm - check if the device should program ASPM
+ *
+ * @adev: amdgpu_device pointer
+ *
+ * Confirm whether the module parameter and pcie bridge agree that ASPM should
+ * be set for this device.
+ *
+ * Returns true if it should be used or false if not.
+ */
+bool amdgpu_device_should_use_aspm(struct amdgpu_device *adev)
+{
+	switch (amdgpu_aspm) {
+	case -1:
+		break;
+	case 0:
+		return false;
+	case 1:
+		return true;
+	default:
+		return false;
+	}
+	return pcie_aspm_enabled(adev->pdev);
+}
+
+bool amdgpu_device_aspm_support_quirk(void)
+{
+#if IS_ENABLED(CONFIG_X86)
+	struct cpuinfo_x86 *c = &cpu_data(0);
+
+	return !(c->x86 == 6 && c->x86_model == INTEL_FAM6_ALDERLAKE);
+#else
+	return true;
+#endif
+}
+
 /* if we get transitioned to only one device, take VGA back */
 /**
  * amdgpu_device_vga_set_decode - enable/disable vga decode
@@ -2069,6 +2147,8 @@
  */
 static int amdgpu_device_ip_early_init(struct amdgpu_device *adev)
 {
+	struct drm_device *dev = adev_to_drm(adev);
+	struct pci_dev *parent;
 	int i, r;
 
 	amdgpu_device_enable_virtual_display(adev);
@@ -2168,6 +2248,18 @@
 		return -EINVAL;
 	}
 
+	if (amdgpu_has_atpx() &&
+	    (amdgpu_is_atpx_hybrid() ||
+	     amdgpu_has_atpx_dgpu_power_cntl()) &&
+	    ((adev->flags & AMD_IS_APU) == 0) &&
+	    !pci_is_thunderbolt_attached(to_pci_dev(dev->dev)))
+		adev->flags |= AMD_IS_PX;
+
+	if (!(adev->flags & AMD_IS_APU)) {
+		parent = pcie_find_root_port(adev->pdev);
+		adev->has_pr3 = parent ? pci_pr3_present(parent) : false;
+	}
+
 	amdgpu_amdkfd_device_probe(adev);
 
 	adev->pm.pp_feature = amdgpu_pp_feature_mask;
@@ -2348,8 +2440,20 @@
 		}
 		adev->ip_blocks[i].status.sw = true;
 
-		/* need to do gmc hw init early so we can allocate gpu mem */
-		if (adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_GMC) {
+		if (adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_COMMON) {
+			/* need to do common hw init early so everything is set up for gmc */
+			r = adev->ip_blocks[i].version->funcs->hw_init((void *)adev);
+			if (r) {
+				DRM_ERROR("hw_init %d failed %d\n", i, r);
+				goto init_failed;
+			}
+			adev->ip_blocks[i].status.hw = true;
+		} else if (adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_GMC) {
+			/* need to do gmc hw init early so we can allocate gpu mem */
+			/* Try to reserve bad pages early */
+			if (amdgpu_sriov_vf(adev))
+				amdgpu_virt_exchange_data(adev);
+
 			r = amdgpu_device_vram_scratch_init(adev);
 			if (r) {
 				DRM_ERROR("amdgpu_vram_scratch_init failed %d\n", r);
@@ -2394,6 +2498,10 @@
 	if (r)
 		goto init_failed;
 
+	r = amdgpu_amdkfd_resume_iommu(adev);
+	if (r)
+		goto init_failed;
+
 	r = amdgpu_device_ip_hw_init_phase1(adev);
 	if (r)
 		goto init_failed;
@@ -2432,15 +2540,9 @@
 	if (!adev->gmc.xgmi.pending_reset)
 		amdgpu_amdkfd_device_init(adev);
 
-	r = amdgpu_amdkfd_resume_iommu(adev);
-	if (r)
-		goto init_failed;
-
 	amdgpu_fru_get_product_info(adev);
 
 init_failed:
-	if (amdgpu_sriov_vf(adev))
-		amdgpu_virt_release_full_gpu(adev, true);
 
 	return r;
 }
@@ -2745,6 +2847,11 @@
 		adev->ip_blocks[i].status.hw = false;
 	}
 
+	if (amdgpu_sriov_vf(adev)) {
+		if (amdgpu_virt_release_full_gpu(adev, false))
+			DRM_ERROR("failed to release exclusive mode on fini\n");
+	}
+
 	return 0;
 }
 
@@ -2805,10 +2912,6 @@
 
 	amdgpu_ras_fini(adev);
 
-	if (amdgpu_sriov_vf(adev))
-		if (amdgpu_virt_release_full_gpu(adev, false))
-			DRM_ERROR("failed to release exclusive mode on fini\n");
-
 	return 0;
 }
 
@@ -2992,8 +3095,8 @@
 	int i, r;
 
 	static enum amd_ip_block_type ip_order[] = {
-		AMD_IP_BLOCK_TYPE_GMC,
 		AMD_IP_BLOCK_TYPE_COMMON,
+		AMD_IP_BLOCK_TYPE_GMC,
 		AMD_IP_BLOCK_TYPE_PSP,
 		AMD_IP_BLOCK_TYPE_IH,
 	};
@@ -3084,7 +3187,8 @@
 			continue;
 		if (adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_COMMON ||
 		    adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_GMC ||
-		    adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_IH) {
+		    adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_IH ||
+		    (adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_PSP && amdgpu_sriov_vf(adev))) {
 
 			r = adev->ip_blocks[i].version->funcs->resume(adev);
 			if (r) {
@@ -3131,6 +3235,15 @@
 			return r;
 		}
 		adev->ip_blocks[i].status.hw = true;
+
+		if (adev->in_s0ix && adev->ip_blocks[i].version->type == AMD_IP_BLOCK_TYPE_SMC) {
+			/* disable gfxoff for IP resume. The gfxoff will be re-enabled in
+			 * amdgpu_device_resume() after IP resume.
+			 */
+			amdgpu_gfx_off_ctrl(adev, false);
+			DRM_DEBUG("will disable gfxoff for re-initializing other blocks\n");
+		}
+
 	}
 
 	return 0;
@@ -3415,6 +3528,7 @@
 	int r, i;
 	bool px = false;
 	u32 max_MBps;
+	int tmp;
 
 	adev->shutdown = false;
 	adev->flags = flags;
@@ -3531,6 +3645,9 @@
 		adev->rmmio_size = pci_resource_len(adev->pdev, 2);
 	}
 
+	for (i = 0; i < AMD_IP_BLOCK_TYPE_NUM; i++)
+		atomic_set(&adev->pm.pwr_state[i], POWER_STATE_UNKNOWN);
+
 	adev->rmmio = ioremap(adev->rmmio_base, adev->rmmio_size);
 	if (adev->rmmio == NULL) {
 		return -ENOMEM;
@@ -3571,6 +3688,11 @@
 	if (r)
 		return r;
 
+	/* Get rid of things like offb */
+	r = drm_aperture_remove_conflicting_pci_framebuffers(adev->pdev, &amdgpu_kms_driver);
+	if (r)
+		return r;
+
 	/* doorbell bar mapping and doorbell index init*/
 	amdgpu_device_doorbell_init(adev);
 
@@ -3606,7 +3728,13 @@
 				}
 			}
 		} else {
+			tmp = amdgpu_reset_method;
+			/* It should do a default reset when loading or reloading the driver,
+			 * regardless of the module parameter reset_method.
+			 */
+			amdgpu_reset_method = AMD_RESET_METHOD_NONE;
 			r = amdgpu_asic_reset(adev);
+			amdgpu_reset_method = tmp;
 			if (r) {
 				dev_err(adev->dev, "asic reset on init failed\n");
 				goto failed;
@@ -3666,18 +3794,6 @@
 
 	r = amdgpu_device_ip_init(adev);
 	if (r) {
-		/* failed in exclusive mode due to timeout */
-		if (amdgpu_sriov_vf(adev) &&
-		    !amdgpu_sriov_runtime(adev) &&
-		    amdgpu_virt_mmio_blocked(adev) &&
-		    !amdgpu_virt_wait_reset(adev)) {
-			dev_err(adev->dev, "VF exclusive mode timeout\n");
-			/* Don't send request since VF is inactive. */
-			adev->virt.caps &= ~AMDGPU_SRIOV_CAPS_RUNTIME;
-			adev->virt.ops = NULL;
-			r = -EAGAIN;
-			goto release_ras_con;
-		}
 		dev_err(adev->dev, "amdgpu_device_ip_init failed\n");
 		amdgpu_vf_error_put(adev, AMDGIM_ERROR_VF_AMDGPU_INIT_FAIL, 0, 0);
 		goto release_ras_con;
@@ -3756,8 +3872,10 @@
 				   msecs_to_jiffies(AMDGPU_RESUME_MS));
 	}
 
-	if (amdgpu_sriov_vf(adev))
+	if (amdgpu_sriov_vf(adev)) {
+		amdgpu_virt_release_full_gpu(adev, true);
 		flush_delayed_work(&adev->delayed_init_work);
+	}
 
 	r = sysfs_create_files(&adev->dev->kobj, amdgpu_dev_attributes);
 	if (r)
@@ -3792,6 +3910,20 @@
 	return 0;
 
 release_ras_con:
+	if (amdgpu_sriov_vf(adev))
+		amdgpu_virt_release_full_gpu(adev, true);
+
+	/* failed in exclusive mode due to timeout */
+	if (amdgpu_sriov_vf(adev) &&
+		!amdgpu_sriov_runtime(adev) &&
+		amdgpu_virt_mmio_blocked(adev) &&
+		!amdgpu_virt_wait_reset(adev)) {
+		dev_err(adev->dev, "VF exclusive mode timeout\n");
+		/* Don't send request since VF is inactive. */
+		adev->virt.caps &= ~AMDGPU_SRIOV_CAPS_RUNTIME;
+		adev->virt.ops = NULL;
+		r = -EAGAIN;
+	}
 	amdgpu_release_ras_context(adev);
 
 failed:
@@ -3850,7 +3982,7 @@
 	/* disable all interrupts */
 	amdgpu_irq_disable_all(adev);
 	if (adev->mode_info.mode_config_initialized){
-		if (!amdgpu_device_has_dc_support(adev))
+		if (!drm_drv_uses_atomic_modeset(adev_to_drm(adev)))
 			drm_helper_force_disable_all(adev_to_drm(adev));
 		else
 			drm_atomic_helper_shutdown(adev_to_drm(adev));
@@ -3909,6 +4041,25 @@
 
 }
 
+/**
+ * amdgpu_device_evict_resources - evict device resources
+ * @adev: amdgpu device object
+ *
+ * Evicts all ttm device resources(vram BOs, gart table) from the lru list
+ * of the vram memory type. Mainly used for evicting device resources
+ * at suspend time.
+ *
+ */
+static void amdgpu_device_evict_resources(struct amdgpu_device *adev)
+{
+	/* No need to evict vram on APUs for suspend to ram or s2idle */
+	if ((adev->in_s3 || adev->in_s0ix) && (adev->flags & AMD_IS_APU))
+		return;
+
+	if (amdgpu_ttm_evict_resources(adev, TTM_PL_VRAM))
+		DRM_WARN("evicting device resources failed\n");
+
+}
 
 /*
  * Suspend & resume.
@@ -3926,12 +4077,20 @@
 int amdgpu_device_suspend(struct drm_device *dev, bool fbcon)
 {
 	struct amdgpu_device *adev = drm_to_adev(dev);
+	int r = 0;
 
 	if (dev->switch_power_state == DRM_SWITCH_POWER_OFF)
 		return 0;
 
 	adev->in_suspend = true;
 
+	if (amdgpu_sriov_vf(adev)) {
+		amdgpu_virt_fini_data_exchange(adev);
+		r = amdgpu_virt_request_full_gpu(adev, false);
+		if (r)
+			return r;
+	}
+
 	if (amdgpu_acpi_smart_shift_update(dev, AMDGPU_SS_DEV_D3))
 		DRM_WARN("smart shift update failed\n");
 
@@ -3949,17 +4108,19 @@
 	if (!adev->in_s0ix)
 		amdgpu_amdkfd_suspend(adev, adev->in_runpm);
 
-	/* evict vram memory */
-	amdgpu_bo_evict_vram(adev);
+	/* First evict vram memory */
+	amdgpu_device_evict_resources(adev);
 
 	amdgpu_fence_driver_hw_fini(adev);
 
 	amdgpu_device_ip_suspend_phase2(adev);
-	/* evict remaining vram memory
-	 * This second call to evict vram is to evict the gart page table
-	 * using the CPU.
+	/* This second call to evict device resources is to evict
+	 * the gart page table using the CPU.
 	 */
-	amdgpu_bo_evict_vram(adev);
+	amdgpu_device_evict_resources(adev);
+
+	if (amdgpu_sriov_vf(adev))
+		amdgpu_virt_release_full_gpu(adev, false);
 
 	return 0;
 }
@@ -3979,6 +4140,12 @@
 	struct amdgpu_device *adev = drm_to_adev(dev);
 	int r = 0;
 
+	if (amdgpu_sriov_vf(adev)) {
+		r = amdgpu_virt_request_full_gpu(adev, true);
+		if (r)
+			return r;
+	}
+
 	if (dev->switch_power_state == DRM_SWITCH_POWER_OFF)
 		return 0;
 
@@ -3993,6 +4160,13 @@
 	}
 
 	r = amdgpu_device_ip_resume(adev);
+
+	/* no matter what r is, always need to properly release full GPU */
+	if (amdgpu_sriov_vf(adev)) {
+		amdgpu_virt_init_data_exchange(adev);
+		amdgpu_virt_release_full_gpu(adev, true);
+	}
+
 	if (r) {
 		dev_err(adev->dev, "amdgpu_device_ip_resume failed (%d).\n", r);
 		return r;
@@ -4015,6 +4189,13 @@
 	/* Make sure IB tests flushed */
 	flush_delayed_work(&adev->delayed_init_work);
 
+	if (adev->in_s0ix) {
+		/* re-enable gfxoff after IP resume. This re-enables gfxoff after
+		 * it was disabled for IP resume in amdgpu_device_ip_resume_phase2().
+		 */
+		amdgpu_gfx_off_ctrl(adev, true);
+		DRM_DEBUG("will enable gfxoff for the mission mode\n");
+	}
 	if (fbcon)
 		amdgpu_fbdev_set_suspend(adev, 0);
 
@@ -4230,9 +4411,14 @@
 	dev_info(adev->dev, "recover vram bo from shadow start\n");
 	mutex_lock(&adev->shadow_list_lock);
 	list_for_each_entry(vmbo, &adev->shadow_list, shadow_list) {
-		shadow = &vmbo->bo;
+		/* If vm is compute context or adev is APU, shadow will be NULL */
+		if (!vmbo->shadow)
+			continue;
+		shadow = vmbo->shadow;
+
 		/* No need to recover an evicted BO */
-		if (shadow->tbo.resource->mem_type != TTM_PL_TT ||
+		if (!shadow->tbo.resource ||
+		    shadow->tbo.resource->mem_type != TTM_PL_TT ||
 		    shadow->tbo.resource->start == AMDGPU_BO_INVALID_OFFSET ||
 		    shadow->parent->tbo.resource->mem_type != TTM_PL_VRAM)
 			continue;
@@ -4466,10 +4652,6 @@
 	if (reset_context->reset_req_dev == adev)
 		job = reset_context->job;
 
-	/* no need to dump if device is not in good state during probe period */
-	if (!adev->gmc.xgmi.pending_reset)
-		amdgpu_debugfs_wait_dump(adev);
-
 	if (amdgpu_sriov_vf(adev)) {
 		/* stop the data exchange thread */
 		amdgpu_virt_fini_data_exchange(adev);
@@ -4791,6 +4973,8 @@
 		pm_runtime_enable(&(p->dev));
 		pm_runtime_resume(&(p->dev));
 	}
+
+	pci_dev_put(p);
 }
 
 static int amdgpu_device_suspend_display_audio(struct amdgpu_device *adev)
@@ -4829,6 +5013,7 @@
 
 		if (expires < ktime_get_mono_fast_ns()) {
 			dev_warn(adev->dev, "failed to suspend display audio\n");
+			pci_dev_put(p);
 			/* TODO: abort the succeeding gpu reset? */
 			return -ETIMEDOUT;
 		}
@@ -4836,6 +5021,7 @@
 
 	pm_runtime_disable(&(p->dev));
 
+	pci_dev_put(p);
 	return 0;
 }
 
@@ -4942,7 +5128,8 @@
 	 * Flush RAM to disk so that after reboot
 	 * the user can read log and see why the system rebooted.
 	 */
-	if (need_emergency_restart && amdgpu_ras_get_context(adev)->reboot) {
+	if (need_emergency_restart && amdgpu_ras_get_context(adev) &&
+		amdgpu_ras_get_context(adev)->reboot) {
 		DRM_WARN("Emergency reboot.");
 
 		ksys_sync_helper();
@@ -5130,7 +5317,7 @@
 			drm_sched_start(&ring->sched, !tmp_adev->asic_reset_res);
 		}
 
-		if (!amdgpu_device_has_dc_support(tmp_adev) && !job_signaled) {
+		if (!drm_drv_uses_atomic_modeset(adev_to_drm(tmp_adev)) && !job_signaled) {
 			drm_helper_resume_force_mode(adev_to_drm(tmp_adev));
 		}
 
@@ -5356,7 +5543,7 @@
 	    adev->nbio.funcs->enable_doorbell_interrupt)
 		adev->nbio.funcs->enable_doorbell_interrupt(adev, true);
 
-	if (amdgpu_passthrough(adev) &&
+	if (amdgpu_passthrough(adev) && adev->nbio.funcs &&
 	    adev->nbio.funcs->clear_doorbell_interrupt)
 		adev->nbio.funcs->clear_doorbell_interrupt(adev);
 
@@ -5567,6 +5754,9 @@
 	struct amdgpu_device *adev = drm_to_adev(dev);
 	int r;
 
+	if (amdgpu_sriov_vf(adev))
+		return false;
+
 	r = pci_save_state(pdev);
 	if (!r) {
 		kfree(adev->pci_state);
@@ -5610,7 +5800,7 @@
 		struct amdgpu_ring *ring)
 {
 #ifdef CONFIG_X86_64
-	if (adev->flags & AMD_IS_APU)
+	if ((adev->flags & AMD_IS_APU) && !amdgpu_passthrough(adev))
 		return;
 #endif
 	if (adev->gmc.xgmi.connected_to_cpu)
@@ -5626,7 +5816,7 @@
 		struct amdgpu_ring *ring)
 {
 #ifdef CONFIG_X86_64
-	if (adev->flags & AMD_IS_APU)
+	if ((adev->flags & AMD_IS_APU) && !amdgpu_passthrough(adev))
 		return;
 #endif
 	if (adev->gmc.xgmi.connected_to_cpu)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c
@@ -415,10 +415,15 @@
 	}
 }
 
+union gc_info {
+	struct gc_info_v1_0 v1;
+	struct gc_info_v2_0 v2;
+};
+
 int amdgpu_discovery_get_gfx_info(struct amdgpu_device *adev)
 {
 	struct binary_header *bhdr;
-	struct gc_info_v1_0 *gc_info;
+	union gc_info *gc_info;
 
 	if (!adev->mman.discovery_bin) {
 		DRM_ERROR("ip discovery uninitialized\n");
@@ -426,27 +431,54 @@
 	}
 
 	bhdr = (struct binary_header *)adev->mman.discovery_bin;
-	gc_info = (struct gc_info_v1_0 *)(adev->mman.discovery_bin +
+	gc_info = (union gc_info *)(adev->mman.discovery_bin +
 			le16_to_cpu(bhdr->table_list[GC].offset));
-
-	adev->gfx.config.max_shader_engines = le32_to_cpu(gc_info->gc_num_se);
-	adev->gfx.config.max_cu_per_sh = 2 * (le32_to_cpu(gc_info->gc_num_wgp0_per_sa) +
-					      le32_to_cpu(gc_info->gc_num_wgp1_per_sa));
-	adev->gfx.config.max_sh_per_se = le32_to_cpu(gc_info->gc_num_sa_per_se);
-	adev->gfx.config.max_backends_per_se = le32_to_cpu(gc_info->gc_num_rb_per_se);
-	adev->gfx.config.max_texture_channel_caches = le32_to_cpu(gc_info->gc_num_gl2c);
-	adev->gfx.config.max_gprs = le32_to_cpu(gc_info->gc_num_gprs);
-	adev->gfx.config.max_gs_threads = le32_to_cpu(gc_info->gc_num_max_gs_thds);
-	adev->gfx.config.gs_vgt_table_depth = le32_to_cpu(gc_info->gc_gs_table_depth);
-	adev->gfx.config.gs_prim_buffer_depth = le32_to_cpu(gc_info->gc_gsprim_buff_depth);
-	adev->gfx.config.double_offchip_lds_buf = le32_to_cpu(gc_info->gc_double_offchip_lds_buffer);
-	adev->gfx.cu_info.wave_front_size = le32_to_cpu(gc_info->gc_wave_size);
-	adev->gfx.cu_info.max_waves_per_simd = le32_to_cpu(gc_info->gc_max_waves_per_simd);
-	adev->gfx.cu_info.max_scratch_slots_per_cu = le32_to_cpu(gc_info->gc_max_scratch_slots_per_cu);
-	adev->gfx.cu_info.lds_size = le32_to_cpu(gc_info->gc_lds_size);
-	adev->gfx.config.num_sc_per_sh = le32_to_cpu(gc_info->gc_num_sc_per_se) /
-					 le32_to_cpu(gc_info->gc_num_sa_per_se);
-	adev->gfx.config.num_packer_per_sc = le32_to_cpu(gc_info->gc_num_packer_per_sc);
-
+	switch (gc_info->v1.header.version_major) {
+	case 1:
+		adev->gfx.config.max_shader_engines = le32_to_cpu(gc_info->v1.gc_num_se);
+		adev->gfx.config.max_cu_per_sh = 2 * (le32_to_cpu(gc_info->v1.gc_num_wgp0_per_sa) +
+						      le32_to_cpu(gc_info->v1.gc_num_wgp1_per_sa));
+		adev->gfx.config.max_sh_per_se = le32_to_cpu(gc_info->v1.gc_num_sa_per_se);
+		adev->gfx.config.max_backends_per_se = le32_to_cpu(gc_info->v1.gc_num_rb_per_se);
+		adev->gfx.config.max_texture_channel_caches = le32_to_cpu(gc_info->v1.gc_num_gl2c);
+		adev->gfx.config.max_gprs = le32_to_cpu(gc_info->v1.gc_num_gprs);
+		adev->gfx.config.max_gs_threads = le32_to_cpu(gc_info->v1.gc_num_max_gs_thds);
+		adev->gfx.config.gs_vgt_table_depth = le32_to_cpu(gc_info->v1.gc_gs_table_depth);
+		adev->gfx.config.gs_prim_buffer_depth = le32_to_cpu(gc_info->v1.gc_gsprim_buff_depth);
+		adev->gfx.config.double_offchip_lds_buf = le32_to_cpu(gc_info->v1.gc_double_offchip_lds_buffer);
+		adev->gfx.cu_info.wave_front_size = le32_to_cpu(gc_info->v1.gc_wave_size);
+		adev->gfx.cu_info.max_waves_per_simd = le32_to_cpu(gc_info->v1.gc_max_waves_per_simd);
+		adev->gfx.cu_info.max_scratch_slots_per_cu = le32_to_cpu(gc_info->v1.gc_max_scratch_slots_per_cu);
+		adev->gfx.cu_info.lds_size = le32_to_cpu(gc_info->v1.gc_lds_size);
+		adev->gfx.config.num_sc_per_sh = le32_to_cpu(gc_info->v1.gc_num_sc_per_se) /
+			le32_to_cpu(gc_info->v1.gc_num_sa_per_se);
+		adev->gfx.config.num_packer_per_sc = le32_to_cpu(gc_info->v1.gc_num_packer_per_sc);
+		break;
+	case 2:
+		adev->gfx.config.max_shader_engines = le32_to_cpu(gc_info->v2.gc_num_se);
+		adev->gfx.config.max_cu_per_sh = le32_to_cpu(gc_info->v2.gc_num_cu_per_sh);
+		adev->gfx.config.max_sh_per_se = le32_to_cpu(gc_info->v2.gc_num_sh_per_se);
+		adev->gfx.config.max_backends_per_se = le32_to_cpu(gc_info->v2.gc_num_rb_per_se);
+		adev->gfx.config.max_texture_channel_caches = le32_to_cpu(gc_info->v2.gc_num_tccs);
+		adev->gfx.config.max_gprs = le32_to_cpu(gc_info->v2.gc_num_gprs);
+		adev->gfx.config.max_gs_threads = le32_to_cpu(gc_info->v2.gc_num_max_gs_thds);
+		adev->gfx.config.gs_vgt_table_depth = le32_to_cpu(gc_info->v2.gc_gs_table_depth);
+		adev->gfx.config.gs_prim_buffer_depth = le32_to_cpu(gc_info->v2.gc_gsprim_buff_depth);
+		adev->gfx.config.double_offchip_lds_buf = le32_to_cpu(gc_info->v2.gc_double_offchip_lds_buffer);
+		adev->gfx.cu_info.wave_front_size = le32_to_cpu(gc_info->v2.gc_wave_size);
+		adev->gfx.cu_info.max_waves_per_simd = le32_to_cpu(gc_info->v2.gc_max_waves_per_simd);
+		adev->gfx.cu_info.max_scratch_slots_per_cu = le32_to_cpu(gc_info->v2.gc_max_scratch_slots_per_cu);
+		adev->gfx.cu_info.lds_size = le32_to_cpu(gc_info->v2.gc_lds_size);
+		adev->gfx.config.num_sc_per_sh = le32_to_cpu(gc_info->v2.gc_num_sc_per_se) /
+			le32_to_cpu(gc_info->v2.gc_num_sh_per_se);
+		adev->gfx.config.num_packer_per_sc = le32_to_cpu(gc_info->v2.gc_num_packer_per_sc);
+		break;
+	default:
+		dev_err(adev->dev,
+			"Unhandled GC info table %d.%d\n",
+			gc_info->v1.header.version_major,
+			gc_info->v1.header.version_minor);
+		return -EINVAL;
+	}
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_display.c
@@ -80,7 +80,7 @@
 
 	struct drm_crtc *crtc = &amdgpu_crtc->base;
 	unsigned long flags;
-	unsigned i;
+	unsigned int i;
 	int vpos, hpos;
 
 	if (amdgpu_display_flip_handle_fence(work, &work->excl))
@@ -159,7 +159,7 @@
 	u64 tiling_flags;
 	int i, r;
 
-	work = kzalloc(sizeof *work, GFP_KERNEL);
+	work = kzalloc(sizeof(*work), GFP_KERNEL);
 	if (work == NULL)
 		return -ENOMEM;
 
@@ -290,18 +290,17 @@
 
 	adev = drm_to_adev(dev);
 	/* if we have active crtcs and we don't have a power ref,
-	   take the current one */
+	 * take the current one
+	 */
 	if (active && !adev->have_disp_power_ref) {
 		adev->have_disp_power_ref = true;
 		return ret;
 	}
-	/* if we have no active crtcs, then drop the power ref
-	   we got before */
-	if (!active && adev->have_disp_power_ref) {
-		pm_runtime_put_autosuspend(dev->dev);
+	/* if we have no active crtcs, then go to
+	 * drop the power ref we got before
+	 */
+	if (!active && adev->have_disp_power_ref)
 		adev->have_disp_power_ref = false;
-	}
-
 out:
 	/* drop the power reference we got coming in here */
 	pm_runtime_put_autosuspend(dev->dev);
@@ -465,11 +464,10 @@
 	if (amdgpu_connector->router.ddc_valid)
 		amdgpu_i2c_router_select_ddc_port(amdgpu_connector);
 
-	if (use_aux) {
+	if (use_aux)
 		ret = i2c_transfer(&amdgpu_connector->ddc_bus->aux.ddc, msgs, 2);
-	} else {
+	else
 		ret = i2c_transfer(&amdgpu_connector->ddc_bus->adapter, msgs, 2);
-	}
 
 	if (ret != 2)
 		/* Couldn't find an accessible DDC on this connector */
@@ -478,10 +476,12 @@
 	 * EDID header starts with:
 	 * 0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00.
 	 * Only the first 6 bytes must be valid as
-	 * drm_edid_block_valid() can fix the last 2 bytes */
+	 * drm_edid_block_valid() can fix the last 2 bytes
+	 */
 	if (drm_edid_header_is_valid(buf) < 6) {
 		/* Couldn't find an accessible EDID on this
-		 * connector */
+		 * connector
+		 */
 		return false;
 	}
 	return true;
@@ -842,8 +842,7 @@
 {
 	u64 micro_tile_mode;
 
-	/* Zero swizzle mode means linear */
-	if (AMDGPU_TILING_GET(afb->tiling_flags, SWIZZLE_MODE) == 0)
+	if (AMDGPU_TILING_GET(afb->tiling_flags, ARRAY_MODE) == 1) /* LINEAR_ALIGNED */
 		return 0;
 
 	micro_tile_mode = AMDGPU_TILING_GET(afb->tiling_flags, MICRO_TILE_MODE);
@@ -1110,6 +1109,7 @@
 		goto err;
 
 	ret = drm_framebuffer_init(dev, &rfb->base, &amdgpu_fb_funcs);
+
 	if (ret)
 		goto err;
 
@@ -1145,7 +1145,7 @@
 	if (ret)
 		return ret;
 
-	if (!dev->mode_config.allow_fb_modifiers) {
+	if (!dev->mode_config.allow_fb_modifiers && !adev->enable_virtual_display) {
 		drm_WARN_ONCE(dev, adev->family >= AMDGPU_FAMILY_AI,
 			      "GFX9+ requires FB check based on format modifier\n");
 		ret = check_tiling_flags_gfx6(rfb);
@@ -1188,8 +1188,10 @@
 
 	obj = drm_gem_object_lookup(file_priv, mode_cmd->handles[0]);
 	if (obj ==  NULL) {
-		drm_dbg_kms(dev, "No GEM object associated to handle 0x%08X, "
-			    "can't create framebuffer\n", mode_cmd->handles[0]);
+		drm_dbg_kms(dev,
+			    "No GEM object associated to handle 0x%08X, can't create framebuffer\n",
+			    mode_cmd->handles[0]);
+
 		return ERR_PTR(-ENOENT);
 	}
 
@@ -1383,6 +1385,7 @@
 	}
 	if (amdgpu_crtc->rmx_type != RMX_OFF) {
 		fixed20_12 a, b;
+
 		a.full = dfixed_const(src_v);
 		b.full = dfixed_const(dst_v);
 		amdgpu_crtc->vsc.full = dfixed_div(a, b);
@@ -1402,7 +1405,7 @@
  *
  * \param dev Device to query.
  * \param pipe Crtc to query.
- * \param flags Flags from caller (DRM_CALLED_FROM_VBLIRQ or 0).
+ * \param flags from caller (DRM_CALLED_FROM_VBLIRQ or 0).
  *              For driver internal use only also supports these flags:
  *
  *              USE_REAL_VBLANKSTART to use the real start of vblank instead
@@ -1478,8 +1481,8 @@
 
 	/* Called from driver internal vblank counter query code? */
 	if (flags & GET_DISTANCE_TO_VBLANKSTART) {
-	    /* Caller wants distance from real vbl_start in *hpos */
-	    *hpos = *vpos - vbl_start;
+		/* Caller wants distance from real vbl_start in *hpos */
+		*hpos = *vpos - vbl_start;
 	}
 
 	/* Fudge vblank to start a few scanlines earlier to handle the
@@ -1501,7 +1504,7 @@
 
 	/* In vblank? */
 	if (in_vbl)
-	    ret |= DRM_SCANOUTPOS_IN_VBLANK;
+		ret |= DRM_SCANOUTPOS_IN_VBLANK;
 
 	/* Called from driver internal vblank counter query code? */
 	if (flags & GET_DISTANCE_TO_VBLANKSTART) {
@@ -1592,6 +1595,7 @@
 
 		if (amdgpu_crtc->cursor_bo && !adev->enable_virtual_display) {
 			struct amdgpu_bo *aobj = gem_to_amdgpu_bo(amdgpu_crtc->cursor_bo);
+
 			r = amdgpu_bo_reserve(aobj, true);
 			if (r == 0) {
 				amdgpu_bo_unpin(aobj);
@@ -1599,9 +1603,9 @@
 			}
 		}
 
-		if (fb == NULL || fb->obj[0] == NULL) {
+		if (!fb || !fb->obj[0])
 			continue;
-		}
+
 		robj = gem_to_amdgpu_bo(fb->obj[0]);
 		/* don't unpin kernel fb objects */
 		if (!amdgpu_fbdev_robj_is_fb(adev, robj)) {
@@ -1629,6 +1633,7 @@
 
 		if (amdgpu_crtc->cursor_bo && !adev->enable_virtual_display) {
 			struct amdgpu_bo *aobj = gem_to_amdgpu_bo(amdgpu_crtc->cursor_bo);
+
 			r = amdgpu_bo_reserve(aobj, true);
 			if (r == 0) {
 				r = amdgpu_bo_pin(aobj, AMDGPU_GEM_DOMAIN_VRAM);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_dma_buf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_dma_buf.c
@@ -384,7 +384,7 @@
 	struct amdgpu_vm_bo_base *bo_base;
 	int r;
 
-	if (bo->tbo.resource->mem_type == TTM_PL_SYSTEM)
+	if (!bo->tbo.resource || bo->tbo.resource->mem_type == TTM_PL_SYSTEM)
 		return;
 
 	r = ttm_bo_validate(&bo->tbo, &placement, &ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_drv.c
@@ -23,7 +23,6 @@
  */
 
 #include <drm/amdgpu_drm.h>
-#include <drm/drm_aperture.h>
 #include <drm/drm_drv.h>
 #include <drm/drm_gem.h>
 #include <drm/drm_vblank.h>
@@ -38,6 +37,7 @@
 #include <drm/drm_probe_helper.h>
 #include <linux/mmu_notifier.h>
 #include <linux/suspend.h>
+#include <linux/fb.h>
 
 #include "amdgpu.h"
 #include "amdgpu_irq.h"
@@ -679,7 +679,7 @@
  * Maximum number of processes that HWS can schedule concurrently. The maximum is the
  * number of VMIDs assigned to the HWS, which is also the default.
  */
-int hws_max_conc_proc = 8;
+int hws_max_conc_proc = -1;
 module_param(hws_max_conc_proc, int, 0444);
 MODULE_PARM_DESC(hws_max_conc_proc,
 	"Max # processes HWS can execute concurrently when sched_policy=0 (0 = no concurrency, #VMIDs for KFD = Maximum(default))");
@@ -890,6 +890,718 @@
 	"specify pptable id to be used (-1 = auto(default) value, 0 = use pptable from vbios, > 0 = soft pptable id)");
 module_param_named(smu_pptable_id, amdgpu_smu_pptable_id, int, 0444);
 
+/* These devices are not supported by amdgpu.
+ * They are supported by the mach64, r128, radeon drivers
+ */
+static const u16 amdgpu_unsupported_pciidlist[] = {
+	/* mach64 */
+	0x4354,
+	0x4358,
+	0x4554,
+	0x4742,
+	0x4744,
+	0x4749,
+	0x474C,
+	0x474D,
+	0x474E,
+	0x474F,
+	0x4750,
+	0x4751,
+	0x4752,
+	0x4753,
+	0x4754,
+	0x4755,
+	0x4756,
+	0x4757,
+	0x4758,
+	0x4759,
+	0x475A,
+	0x4C42,
+	0x4C44,
+	0x4C47,
+	0x4C49,
+	0x4C4D,
+	0x4C4E,
+	0x4C50,
+	0x4C51,
+	0x4C52,
+	0x4C53,
+	0x5654,
+	0x5655,
+	0x5656,
+	/* r128 */
+	0x4c45,
+	0x4c46,
+	0x4d46,
+	0x4d4c,
+	0x5041,
+	0x5042,
+	0x5043,
+	0x5044,
+	0x5045,
+	0x5046,
+	0x5047,
+	0x5048,
+	0x5049,
+	0x504A,
+	0x504B,
+	0x504C,
+	0x504D,
+	0x504E,
+	0x504F,
+	0x5050,
+	0x5051,
+	0x5052,
+	0x5053,
+	0x5054,
+	0x5055,
+	0x5056,
+	0x5057,
+	0x5058,
+	0x5245,
+	0x5246,
+	0x5247,
+	0x524b,
+	0x524c,
+	0x534d,
+	0x5446,
+	0x544C,
+	0x5452,
+	/* radeon */
+	0x3150,
+	0x3151,
+	0x3152,
+	0x3154,
+	0x3155,
+	0x3E50,
+	0x3E54,
+	0x4136,
+	0x4137,
+	0x4144,
+	0x4145,
+	0x4146,
+	0x4147,
+	0x4148,
+	0x4149,
+	0x414A,
+	0x414B,
+	0x4150,
+	0x4151,
+	0x4152,
+	0x4153,
+	0x4154,
+	0x4155,
+	0x4156,
+	0x4237,
+	0x4242,
+	0x4336,
+	0x4337,
+	0x4437,
+	0x4966,
+	0x4967,
+	0x4A48,
+	0x4A49,
+	0x4A4A,
+	0x4A4B,
+	0x4A4C,
+	0x4A4D,
+	0x4A4E,
+	0x4A4F,
+	0x4A50,
+	0x4A54,
+	0x4B48,
+	0x4B49,
+	0x4B4A,
+	0x4B4B,
+	0x4B4C,
+	0x4C57,
+	0x4C58,
+	0x4C59,
+	0x4C5A,
+	0x4C64,
+	0x4C66,
+	0x4C67,
+	0x4E44,
+	0x4E45,
+	0x4E46,
+	0x4E47,
+	0x4E48,
+	0x4E49,
+	0x4E4A,
+	0x4E4B,
+	0x4E50,
+	0x4E51,
+	0x4E52,
+	0x4E53,
+	0x4E54,
+	0x4E56,
+	0x5144,
+	0x5145,
+	0x5146,
+	0x5147,
+	0x5148,
+	0x514C,
+	0x514D,
+	0x5157,
+	0x5158,
+	0x5159,
+	0x515A,
+	0x515E,
+	0x5460,
+	0x5462,
+	0x5464,
+	0x5548,
+	0x5549,
+	0x554A,
+	0x554B,
+	0x554C,
+	0x554D,
+	0x554E,
+	0x554F,
+	0x5550,
+	0x5551,
+	0x5552,
+	0x5554,
+	0x564A,
+	0x564B,
+	0x564F,
+	0x5652,
+	0x5653,
+	0x5657,
+	0x5834,
+	0x5835,
+	0x5954,
+	0x5955,
+	0x5974,
+	0x5975,
+	0x5960,
+	0x5961,
+	0x5962,
+	0x5964,
+	0x5965,
+	0x5969,
+	0x5a41,
+	0x5a42,
+	0x5a61,
+	0x5a62,
+	0x5b60,
+	0x5b62,
+	0x5b63,
+	0x5b64,
+	0x5b65,
+	0x5c61,
+	0x5c63,
+	0x5d48,
+	0x5d49,
+	0x5d4a,
+	0x5d4c,
+	0x5d4d,
+	0x5d4e,
+	0x5d4f,
+	0x5d50,
+	0x5d52,
+	0x5d57,
+	0x5e48,
+	0x5e4a,
+	0x5e4b,
+	0x5e4c,
+	0x5e4d,
+	0x5e4f,
+	0x6700,
+	0x6701,
+	0x6702,
+	0x6703,
+	0x6704,
+	0x6705,
+	0x6706,
+	0x6707,
+	0x6708,
+	0x6709,
+	0x6718,
+	0x6719,
+	0x671c,
+	0x671d,
+	0x671f,
+	0x6720,
+	0x6721,
+	0x6722,
+	0x6723,
+	0x6724,
+	0x6725,
+	0x6726,
+	0x6727,
+	0x6728,
+	0x6729,
+	0x6738,
+	0x6739,
+	0x673e,
+	0x6740,
+	0x6741,
+	0x6742,
+	0x6743,
+	0x6744,
+	0x6745,
+	0x6746,
+	0x6747,
+	0x6748,
+	0x6749,
+	0x674A,
+	0x6750,
+	0x6751,
+	0x6758,
+	0x6759,
+	0x675B,
+	0x675D,
+	0x675F,
+	0x6760,
+	0x6761,
+	0x6762,
+	0x6763,
+	0x6764,
+	0x6765,
+	0x6766,
+	0x6767,
+	0x6768,
+	0x6770,
+	0x6771,
+	0x6772,
+	0x6778,
+	0x6779,
+	0x677B,
+	0x6840,
+	0x6841,
+	0x6842,
+	0x6843,
+	0x6849,
+	0x684C,
+	0x6850,
+	0x6858,
+	0x6859,
+	0x6880,
+	0x6888,
+	0x6889,
+	0x688A,
+	0x688C,
+	0x688D,
+	0x6898,
+	0x6899,
+	0x689b,
+	0x689c,
+	0x689d,
+	0x689e,
+	0x68a0,
+	0x68a1,
+	0x68a8,
+	0x68a9,
+	0x68b0,
+	0x68b8,
+	0x68b9,
+	0x68ba,
+	0x68be,
+	0x68bf,
+	0x68c0,
+	0x68c1,
+	0x68c7,
+	0x68c8,
+	0x68c9,
+	0x68d8,
+	0x68d9,
+	0x68da,
+	0x68de,
+	0x68e0,
+	0x68e1,
+	0x68e4,
+	0x68e5,
+	0x68e8,
+	0x68e9,
+	0x68f1,
+	0x68f2,
+	0x68f8,
+	0x68f9,
+	0x68fa,
+	0x68fe,
+	0x7100,
+	0x7101,
+	0x7102,
+	0x7103,
+	0x7104,
+	0x7105,
+	0x7106,
+	0x7108,
+	0x7109,
+	0x710A,
+	0x710B,
+	0x710C,
+	0x710E,
+	0x710F,
+	0x7140,
+	0x7141,
+	0x7142,
+	0x7143,
+	0x7144,
+	0x7145,
+	0x7146,
+	0x7147,
+	0x7149,
+	0x714A,
+	0x714B,
+	0x714C,
+	0x714D,
+	0x714E,
+	0x714F,
+	0x7151,
+	0x7152,
+	0x7153,
+	0x715E,
+	0x715F,
+	0x7180,
+	0x7181,
+	0x7183,
+	0x7186,
+	0x7187,
+	0x7188,
+	0x718A,
+	0x718B,
+	0x718C,
+	0x718D,
+	0x718F,
+	0x7193,
+	0x7196,
+	0x719B,
+	0x719F,
+	0x71C0,
+	0x71C1,
+	0x71C2,
+	0x71C3,
+	0x71C4,
+	0x71C5,
+	0x71C6,
+	0x71C7,
+	0x71CD,
+	0x71CE,
+	0x71D2,
+	0x71D4,
+	0x71D5,
+	0x71D6,
+	0x71DA,
+	0x71DE,
+	0x7200,
+	0x7210,
+	0x7211,
+	0x7240,
+	0x7243,
+	0x7244,
+	0x7245,
+	0x7246,
+	0x7247,
+	0x7248,
+	0x7249,
+	0x724A,
+	0x724B,
+	0x724C,
+	0x724D,
+	0x724E,
+	0x724F,
+	0x7280,
+	0x7281,
+	0x7283,
+	0x7284,
+	0x7287,
+	0x7288,
+	0x7289,
+	0x728B,
+	0x728C,
+	0x7290,
+	0x7291,
+	0x7293,
+	0x7297,
+	0x7834,
+	0x7835,
+	0x791e,
+	0x791f,
+	0x793f,
+	0x7941,
+	0x7942,
+	0x796c,
+	0x796d,
+	0x796e,
+	0x796f,
+	0x9400,
+	0x9401,
+	0x9402,
+	0x9403,
+	0x9405,
+	0x940A,
+	0x940B,
+	0x940F,
+	0x94A0,
+	0x94A1,
+	0x94A3,
+	0x94B1,
+	0x94B3,
+	0x94B4,
+	0x94B5,
+	0x94B9,
+	0x9440,
+	0x9441,
+	0x9442,
+	0x9443,
+	0x9444,
+	0x9446,
+	0x944A,
+	0x944B,
+	0x944C,
+	0x944E,
+	0x9450,
+	0x9452,
+	0x9456,
+	0x945A,
+	0x945B,
+	0x945E,
+	0x9460,
+	0x9462,
+	0x946A,
+	0x946B,
+	0x947A,
+	0x947B,
+	0x9480,
+	0x9487,
+	0x9488,
+	0x9489,
+	0x948A,
+	0x948F,
+	0x9490,
+	0x9491,
+	0x9495,
+	0x9498,
+	0x949C,
+	0x949E,
+	0x949F,
+	0x94C0,
+	0x94C1,
+	0x94C3,
+	0x94C4,
+	0x94C5,
+	0x94C6,
+	0x94C7,
+	0x94C8,
+	0x94C9,
+	0x94CB,
+	0x94CC,
+	0x94CD,
+	0x9500,
+	0x9501,
+	0x9504,
+	0x9505,
+	0x9506,
+	0x9507,
+	0x9508,
+	0x9509,
+	0x950F,
+	0x9511,
+	0x9515,
+	0x9517,
+	0x9519,
+	0x9540,
+	0x9541,
+	0x9542,
+	0x954E,
+	0x954F,
+	0x9552,
+	0x9553,
+	0x9555,
+	0x9557,
+	0x955f,
+	0x9580,
+	0x9581,
+	0x9583,
+	0x9586,
+	0x9587,
+	0x9588,
+	0x9589,
+	0x958A,
+	0x958B,
+	0x958C,
+	0x958D,
+	0x958E,
+	0x958F,
+	0x9590,
+	0x9591,
+	0x9593,
+	0x9595,
+	0x9596,
+	0x9597,
+	0x9598,
+	0x9599,
+	0x959B,
+	0x95C0,
+	0x95C2,
+	0x95C4,
+	0x95C5,
+	0x95C6,
+	0x95C7,
+	0x95C9,
+	0x95CC,
+	0x95CD,
+	0x95CE,
+	0x95CF,
+	0x9610,
+	0x9611,
+	0x9612,
+	0x9613,
+	0x9614,
+	0x9615,
+	0x9616,
+	0x9640,
+	0x9641,
+	0x9642,
+	0x9643,
+	0x9644,
+	0x9645,
+	0x9647,
+	0x9648,
+	0x9649,
+	0x964a,
+	0x964b,
+	0x964c,
+	0x964e,
+	0x964f,
+	0x9710,
+	0x9711,
+	0x9712,
+	0x9713,
+	0x9714,
+	0x9715,
+	0x9802,
+	0x9803,
+	0x9804,
+	0x9805,
+	0x9806,
+	0x9807,
+	0x9808,
+	0x9809,
+	0x980A,
+	0x9900,
+	0x9901,
+	0x9903,
+	0x9904,
+	0x9905,
+	0x9906,
+	0x9907,
+	0x9908,
+	0x9909,
+	0x990A,
+	0x990B,
+	0x990C,
+	0x990D,
+	0x990E,
+	0x990F,
+	0x9910,
+	0x9913,
+	0x9917,
+	0x9918,
+	0x9919,
+	0x9990,
+	0x9991,
+	0x9992,
+	0x9993,
+	0x9994,
+	0x9995,
+	0x9996,
+	0x9997,
+	0x9998,
+	0x9999,
+	0x999A,
+	0x999B,
+	0x999C,
+	0x999D,
+	0x99A0,
+	0x99A2,
+	0x99A4,
+	/* radeon secondary ids */
+	0x3171,
+	0x3e70,
+	0x4164,
+	0x4165,
+	0x4166,
+	0x4168,
+	0x4170,
+	0x4171,
+	0x4172,
+	0x4173,
+	0x496e,
+	0x4a69,
+	0x4a6a,
+	0x4a6b,
+	0x4a70,
+	0x4a74,
+	0x4b69,
+	0x4b6b,
+	0x4b6c,
+	0x4c6e,
+	0x4e64,
+	0x4e65,
+	0x4e66,
+	0x4e67,
+	0x4e68,
+	0x4e69,
+	0x4e6a,
+	0x4e71,
+	0x4f73,
+	0x5569,
+	0x556b,
+	0x556d,
+	0x556f,
+	0x5571,
+	0x5854,
+	0x5874,
+	0x5940,
+	0x5941,
+	0x5b70,
+	0x5b72,
+	0x5b73,
+	0x5b74,
+	0x5b75,
+	0x5d44,
+	0x5d45,
+	0x5d6d,
+	0x5d6f,
+	0x5d72,
+	0x5d77,
+	0x5e6b,
+	0x5e6d,
+	0x7120,
+	0x7124,
+	0x7129,
+	0x712e,
+	0x712f,
+	0x7162,
+	0x7163,
+	0x7166,
+	0x7167,
+	0x7172,
+	0x7173,
+	0x71a0,
+	0x71a1,
+	0x71a3,
+	0x71a7,
+	0x71bb,
+	0x71e0,
+	0x71e1,
+	0x71e2,
+	0x71e6,
+	0x71e7,
+	0x71f2,
+	0x7269,
+	0x726b,
+	0x726e,
+	0x72a0,
+	0x72a8,
+	0x72b1,
+	0x72b3,
+	0x793f,
+};
+
 static const struct pci_device_id pciidlist[] = {
 #ifdef  CONFIG_DRM_AMDGPU_SI
 	{0x1002, 0x6780, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI},
@@ -1224,10 +1936,10 @@
 	{0x1002, 0x73FF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_DIMGREY_CAVEFISH},
 
 	/* Aldebaran */
-	{0x1002, 0x7408, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN|AMD_EXP_HW_SUPPORT},
-	{0x1002, 0x740C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN|AMD_EXP_HW_SUPPORT},
-	{0x1002, 0x740F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN|AMD_EXP_HW_SUPPORT},
-	{0x1002, 0x7410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN|AMD_EXP_HW_SUPPORT},
+	{0x1002, 0x7408, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN},
+	{0x1002, 0x740C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN},
+	{0x1002, 0x740F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN},
+	{0x1002, 0x7410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_ALDEBARAN},
 
 	/* CYAN_SKILLFISH */
 	{0x1002, 0x13FE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_CYAN_SKILLFISH|AMD_IS_APU},
@@ -1237,6 +1949,7 @@
 	{0x1002, 0x7421, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BEIGE_GOBY},
 	{0x1002, 0x7422, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BEIGE_GOBY},
 	{0x1002, 0x7423, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BEIGE_GOBY},
+	{0x1002, 0x7424, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BEIGE_GOBY},
 	{0x1002, 0x743F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BEIGE_GOBY},
 
 	{0, 0, 0}
@@ -1246,14 +1959,42 @@
 
 static const struct drm_driver amdgpu_kms_driver;
 
+static bool amdgpu_is_fw_framebuffer(resource_size_t base,
+				     resource_size_t size)
+{
+	bool found = false;
+#if IS_REACHABLE(CONFIG_FB)
+	struct apertures_struct *a;
+
+	a = alloc_apertures(1);
+	if (!a)
+		return false;
+
+	a->ranges[0].base = base;
+	a->ranges[0].size = size;
+
+	found = is_firmware_framebuffer(a);
+	kfree(a);
+#endif
+	return found;
+}
+
 static int amdgpu_pci_probe(struct pci_dev *pdev,
 			    const struct pci_device_id *ent)
 {
 	struct drm_device *ddev;
 	struct amdgpu_device *adev;
 	unsigned long flags = ent->driver_data;
-	int ret, retry = 0;
+	int ret, retry = 0, i;
 	bool supports_atomic = false;
+	bool is_fw_fb;
+	resource_size_t base, size;
+
+	/* skip devices which are owned by radeon */
+	for (i = 0; i < ARRAY_SIZE(amdgpu_unsupported_pciidlist); i++) {
+		if (amdgpu_unsupported_pciidlist[i] == pdev->device)
+			return -ENODEV;
+	}
 
 	if (amdgpu_virtual_display ||
 	    amdgpu_device_asic_has_dc_support(flags & AMD_ASIC_MASK))
@@ -1264,6 +2005,15 @@
 			 "See modparam exp_hw_support\n");
 		return -ENODEV;
 	}
+	/* differentiate between P10 and P11 asics with the same DID */
+	if (pdev->device == 0x67FF &&
+	    (pdev->revision == 0xE3 ||
+	     pdev->revision == 0xE7 ||
+	     pdev->revision == 0xF3 ||
+	     pdev->revision == 0xF7)) {
+		flags &= ~AMD_ASIC_MASK;
+		flags |= CHIP_POLARIS10;
+	}
 
 	/* Due to hardware bugs, S/G Display on raven requires a 1:1 IOMMU mapping,
 	 * however, SME requires an indirect IOMMU mapping because the encryption
@@ -1310,10 +2060,9 @@
 	}
 #endif
 
-	/* Get rid of things like offb */
-	ret = drm_aperture_remove_conflicting_pci_framebuffers(pdev, &amdgpu_kms_driver);
-	if (ret)
-		return ret;
+	base = pci_resource_start(pdev, 0);
+	size = pci_resource_len(pdev, 0);
+	is_fw_fb = amdgpu_is_fw_framebuffer(base, size);
 
 	adev = devm_drm_dev_alloc(&pdev->dev, &amdgpu_kms_driver, typeof(*adev), ddev);
 	if (IS_ERR(adev))
@@ -1322,6 +2071,7 @@
 	adev->dev  = &pdev->dev;
 	adev->pdev = pdev;
 	ddev = adev_to_drm(adev);
+	adev->is_fw_fb = is_fw_fb;
 
 	if (!supports_atomic)
 		ddev->driver_features &= ~DRIVER_ATOMIC;
@@ -1332,12 +2082,12 @@
 
 	pci_set_drvdata(pdev, ddev);
 
-	ret = amdgpu_driver_load_kms(adev, ent->driver_data);
+	ret = amdgpu_driver_load_kms(adev, flags);
 	if (ret)
 		goto err_pci;
 
 retry_init:
-	ret = drm_dev_register(ddev, ent->driver_data);
+	ret = drm_dev_register(ddev, flags);
 	if (ret == -EAGAIN && ++retry <= 3) {
 		DRM_INFO("retry init %d\n", retry);
 		/* Don't request EX mode too frequently which is attacking */
@@ -1471,13 +2221,20 @@
 static int amdgpu_pmops_prepare(struct device *dev)
 {
 	struct drm_device *drm_dev = dev_get_drvdata(dev);
+	struct amdgpu_device *adev = drm_to_adev(drm_dev);
 
 	/* Return a positive number here so
 	 * DPM_FLAG_SMART_SUSPEND works properly
 	 */
 	if (amdgpu_device_supports_boco(drm_dev))
-		return pm_runtime_suspended(dev) &&
-			pm_suspend_via_firmware();
+		return pm_runtime_suspended(dev);
+
+	/* if we will not support s3 or s2i for the device
+	 *  then skip suspend
+	 */
+	if (!amdgpu_acpi_is_s0ix_active(adev) &&
+	    !amdgpu_acpi_is_s3_active(adev))
+		return 1;
 
 	return 0;
 }
@@ -1491,15 +2248,25 @@
 {
 	struct drm_device *drm_dev = dev_get_drvdata(dev);
 	struct amdgpu_device *adev = drm_to_adev(drm_dev);
-	int r;
 
+	adev->suspend_complete = false;
 	if (amdgpu_acpi_is_s0ix_active(adev))
 		adev->in_s0ix = true;
-	adev->in_s3 = true;
-	r = amdgpu_device_suspend(drm_dev, true);
-	adev->in_s3 = false;
+	else
+		adev->in_s3 = true;
+	return amdgpu_device_suspend(drm_dev, true);
+}
 
-	return r;
+static int amdgpu_pmops_suspend_noirq(struct device *dev)
+{
+	struct drm_device *drm_dev = dev_get_drvdata(dev);
+	struct amdgpu_device *adev = drm_to_adev(drm_dev);
+
+	adev->suspend_complete = true;
+	if (amdgpu_acpi_should_gpu_reset(adev))
+		return amdgpu_asic_reset(adev);
+
+	return 0;
 }
 
 static int amdgpu_pmops_resume(struct device *dev)
@@ -1511,6 +2278,8 @@
 	r = amdgpu_device_resume(drm_dev, true);
 	if (amdgpu_acpi_is_s0ix_active(adev))
 		adev->in_s0ix = false;
+	else
+		adev->in_s3 = false;
 	return r;
 }
 
@@ -1522,7 +2291,6 @@
 
 	adev->in_s4 = true;
 	r = amdgpu_device_suspend(drm_dev, true);
-	adev->in_s4 = false;
 	if (r)
 		return r;
 	return amdgpu_asic_reset(adev);
@@ -1531,8 +2299,13 @@
 static int amdgpu_pmops_thaw(struct device *dev)
 {
 	struct drm_device *drm_dev = dev_get_drvdata(dev);
+	struct amdgpu_device *adev = drm_to_adev(drm_dev);
+	int r;
 
-	return amdgpu_device_resume(drm_dev, true);
+	r = amdgpu_device_resume(drm_dev, true);
+	adev->in_s4 = false;
+
+	return r;
 }
 
 static int amdgpu_pmops_poweroff(struct device *dev)
@@ -1545,6 +2318,9 @@
 static int amdgpu_pmops_restore(struct device *dev)
 {
 	struct drm_device *drm_dev = dev_get_drvdata(dev);
+	struct amdgpu_device *adev = drm_to_adev(drm_dev);
+
+	adev->in_s4 = false;
 
 	return amdgpu_device_resume(drm_dev, true);
 }
@@ -1575,12 +2351,27 @@
 	if (amdgpu_device_supports_px(drm_dev))
 		drm_dev->switch_power_state = DRM_SWITCH_POWER_CHANGING;
 
+	/*
+	 * By setting mp1_state as PP_MP1_STATE_UNLOAD, MP1 will do some
+	 * proper cleanups and put itself into a state ready for PNP. That
+	 * can address some random resuming failure observed on BOCO capable
+	 * platforms.
+	 * TODO: this may be also needed for PX capable platform.
+	 */
+	if (amdgpu_device_supports_boco(drm_dev))
+		adev->mp1_state = PP_MP1_STATE_UNLOAD;
+
 	ret = amdgpu_device_suspend(drm_dev, false);
 	if (ret) {
 		adev->in_runpm = false;
+		if (amdgpu_device_supports_boco(drm_dev))
+			adev->mp1_state = PP_MP1_STATE_NONE;
 		return ret;
 	}
 
+	if (amdgpu_device_supports_boco(drm_dev))
+		adev->mp1_state = PP_MP1_STATE_NONE;
+
 	if (amdgpu_device_supports_px(drm_dev)) {
 		/* Only need to handle PCI state in the driver for ATPX
 		 * PCI core handles it for _PR3.
@@ -1634,8 +2425,11 @@
 		amdgpu_device_baco_exit(drm_dev);
 	}
 	ret = amdgpu_device_resume(drm_dev, false);
-	if (ret)
+	if (ret) {
+		if (amdgpu_device_supports_px(drm_dev))
+			pci_disable_device(pdev);
 		return ret;
+	}
 
 	if (amdgpu_device_supports_px(drm_dev))
 		drm_dev->switch_power_state = DRM_SWITCH_POWER_ON;
@@ -1719,6 +2513,7 @@
 	.prepare = amdgpu_pmops_prepare,
 	.complete = amdgpu_pmops_complete,
 	.suspend = amdgpu_pmops_suspend,
+	.suspend_noirq = amdgpu_pmops_suspend_noirq,
 	.resume = amdgpu_pmops_resume,
 	.freeze = amdgpu_pmops_freeze,
 	.thaw = amdgpu_pmops_thaw,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_eeprom.c
@@ -177,7 +177,7 @@
  * Returns the number of bytes read/written; -errno on error.
  */
 static int amdgpu_eeprom_xfer(struct i2c_adapter *i2c_adap, u32 eeprom_addr,
-			      u8 *eeprom_buf, u16 buf_size, bool read)
+			      u8 *eeprom_buf, u32 buf_size, bool read)
 {
 	const struct i2c_adapter_quirks *quirks = i2c_adap->quirks;
 	u16 limit;
@@ -224,7 +224,7 @@
 
 int amdgpu_eeprom_read(struct i2c_adapter *i2c_adap,
 		       u32 eeprom_addr, u8 *eeprom_buf,
-		       u16 bytes)
+		       u32 bytes)
 {
 	return amdgpu_eeprom_xfer(i2c_adap, eeprom_addr, eeprom_buf, bytes,
 				  true);
@@ -232,7 +232,7 @@
 
 int amdgpu_eeprom_write(struct i2c_adapter *i2c_adap,
 			u32 eeprom_addr, u8 *eeprom_buf,
-			u16 bytes)
+			u32 bytes)
 {
 	return amdgpu_eeprom_xfer(i2c_adap, eeprom_addr, eeprom_buf, bytes,
 				  false);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_eeprom.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_eeprom.h
@@ -28,10 +28,10 @@
 
 int amdgpu_eeprom_read(struct i2c_adapter *i2c_adap,
 		       u32 eeprom_addr, u8 *eeprom_buf,
-		       u16 bytes);
+		       u32 bytes);
 
 int amdgpu_eeprom_write(struct i2c_adapter *i2c_adap,
 			u32 eeprom_addr, u8 *eeprom_buf,
-			u16 bytes);
+			u32 bytes);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_fb.c
@@ -341,7 +341,8 @@
 	}
 
 	/* disable all the possible outputs/crtcs before entering KMS mode */
-	if (!amdgpu_device_has_dc_support(adev) && !amdgpu_virtual_display)
+	if (!amdgpu_device_has_dc_support(adev) && !amdgpu_virtual_display &&
+	    !amdgpu_sriov_vf(adev))
 		drm_helper_disable_unused_functions(adev_to_drm(adev));
 
 	drm_fb_helper_initial_config(&rfbdev->helper, bpp_sel);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c
@@ -552,9 +552,6 @@
 		if (!ring || !ring->fence_drv.initialized)
 			continue;
 
-		if (!ring->no_scheduler)
-			drm_sched_stop(&ring->sched, NULL);
-
 		/* You can't wait for HW to signal if it's gone */
 		if (!drm_dev_is_unplugged(&adev->ddev))
 			r = amdgpu_fence_wait_empty(ring);
@@ -564,7 +561,8 @@
 		if (r)
 			amdgpu_fence_driver_force_completion(ring);
 
-		if (ring->fence_drv.irq_src)
+		if (!drm_dev_is_unplugged(adev_to_drm(adev)) &&
+		    ring->fence_drv.irq_src)
 			amdgpu_irq_put(adev, ring->fence_drv.irq_src,
 				       ring->fence_drv.irq_type);
 
@@ -582,7 +580,13 @@
 		if (!ring || !ring->fence_drv.initialized)
 			continue;
 
-		if (!ring->no_scheduler)
+		/*
+		 * Notice we check for sched.ops since there's some
+		 * override on the meaning of sched.ready by amdgpu.
+		 * The natural check would be sched.ready, which is
+		 * set as drm_sched_init() finishes...
+		 */
+		if (ring->sched.ops)
 			drm_sched_fini(&ring->sched);
 
 		for (j = 0; j <= ring->fence_drv.num_fences_mask; ++j)
@@ -614,11 +618,6 @@
 		if (!ring || !ring->fence_drv.initialized)
 			continue;
 
-		if (!ring->no_scheduler) {
-			drm_sched_resubmit_jobs(&ring->sched);
-			drm_sched_start(&ring->sched, true);
-		}
-
 		/* enable the interrupt */
 		if (ring->fence_drv.irq_src)
 			amdgpu_irq_get(adev, ring->fence_drv.irq_src,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_gem.c
@@ -61,7 +61,7 @@
 		}
 
 		 ret = ttm_bo_vm_fault_reserved(vmf, vmf->vma->vm_page_prot,
-						TTM_BO_VM_NUM_PREFAULT, 1);
+						TTM_BO_VM_NUM_PREFAULT);
 
 		 drm_dev_exit(idx);
 	} else {
@@ -419,11 +419,9 @@
 	if (r)
 		goto release_object;
 
-	if (args->flags & AMDGPU_GEM_USERPTR_REGISTER) {
-		r = amdgpu_mn_register(bo, args->addr);
-		if (r)
-			goto release_object;
-	}
+	r = amdgpu_mn_register(bo, args->addr);
+	if (r)
+		goto release_object;
 
 	if (args->flags & AMDGPU_GEM_USERPTR_VALIDATE) {
 		r = amdgpu_ttm_tt_get_user_pages(bo, bo->tbo.ttm->pages);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_gfx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_gfx.c
@@ -266,7 +266,7 @@
 		    * adev->gfx.mec.num_pipe_per_mec
 		    * adev->gfx.mec.num_queue_per_pipe;
 
-	while (queue_bit-- >= 0) {
+	while (--queue_bit >= 0) {
 		if (test_bit(queue_bit, adev->gfx.mec.queue_bitmap))
 			continue;
 
@@ -580,10 +580,14 @@
 		if (adev->gfx.gfx_off_req_count == 0 &&
 		    !adev->gfx.gfx_off_state) {
 			/* If going to s2idle, no need to wait */
-			if (adev->in_s0ix)
-				delay = GFX_OFF_NO_DELAY;
-			schedule_delayed_work(&adev->gfx.gfx_off_delay_work,
+			if (adev->in_s0ix) {
+				if (!amdgpu_dpm_set_powergating_by_smu(adev,
+						AMD_IP_BLOCK_TYPE_GFX, true))
+					adev->gfx.gfx_off_state = true;
+			} else {
+				schedule_delayed_work(&adev->gfx.gfx_off_delay_work,
 					      delay);
+			}
 		}
 	} else {
 		if (adev->gfx.gfx_off_req_count == 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_gtt_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_gtt_mgr.c
@@ -169,6 +169,7 @@
 	return 0;
 
 err_free:
+	ttm_resource_fini(man, &node->base.base);
 	kfree(node);
 
 err_out:
@@ -200,6 +201,7 @@
 	if (!(res->placement & TTM_PL_FLAG_TEMPORARY))
 		atomic64_sub(res->num_pages, &mgr->used);
 
+	ttm_resource_fini(man, res);
 	kfree(node);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ih.c
@@ -223,7 +223,7 @@
  */
 int amdgpu_ih_process(struct amdgpu_device *adev, struct amdgpu_ih_ring *ih)
 {
-	unsigned int count = AMDGPU_IH_MAX_NUM_IVS;
+	unsigned int count;
 	u32 wptr;
 
 	if (!ih->enabled || adev->shutdown)
@@ -232,6 +232,7 @@
 	wptr = amdgpu_ih_get_wptr(adev, ih);
 
 restart_ih:
+	count  = AMDGPU_IH_MAX_NUM_IVS;
 	DRM_DEBUG("%s: rptr %d, wptr %d\n", __func__, ih->rptr, wptr);
 
 	/* Order reading of wptr vs. reading of IH ring data */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_irq.c
@@ -494,6 +494,14 @@
 
 	entry.ih = ih;
 	entry.iv_entry = (const uint32_t *)&ih->ring[ring_index];
+
+	/*
+	 * timestamp is not supported on some legacy SOCs (cik, cz, iceland,
+	 * si and tonga), so initialize timestamp and timestamp_src to 0
+	 */
+	entry.timestamp = 0;
+	entry.timestamp_src = 0;
+
 	amdgpu_ih_decode_iv(adev, &entry);
 
 	trace_amdgpu_iv(ih - &adev->irq.ih, &entry);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_kms.c
@@ -43,6 +43,17 @@
 #include "amdgpu_display.h"
 #include "amdgpu_ras.h"
 
+static void amdgpu_runtime_pm_quirk(struct amdgpu_device *adev)
+{
+	/*
+	 * Add below quirk on several sienna_cichlid cards to disable
+	 * runtime pm to fix EMI failures.
+	 */
+	if (((adev->pdev->device == 0x73A1) && (adev->pdev->revision == 0x00)) ||
+	    ((adev->pdev->device == 0x73BF) && (adev->pdev->revision == 0xCF)))
+		adev->runpm = false;
+}
+
 void amdgpu_unregister_gpu_instance(struct amdgpu_device *adev)
 {
 	struct amdgpu_gpu_instance *gpu_instance;
@@ -152,21 +163,10 @@
 int amdgpu_driver_load_kms(struct amdgpu_device *adev, unsigned long flags)
 {
 	struct drm_device *dev;
-	struct pci_dev *parent;
 	int r, acpi_status;
 
 	dev = adev_to_drm(adev);
 
-	if (amdgpu_has_atpx() &&
-	    (amdgpu_is_atpx_hybrid() ||
-	     amdgpu_has_atpx_dgpu_power_cntl()) &&
-	    ((flags & AMD_IS_APU) == 0) &&
-	    !pci_is_thunderbolt_attached(to_pci_dev(dev->dev)))
-		flags |= AMD_IS_PX;
-
-	parent = pci_upstream_bridge(adev->pdev);
-	adev->has_pr3 = parent ? pci_pr3_present(parent) : false;
-
 	/* amdgpu_device_init should report only fatal error
 	 * like memory allocation failure or iomapping failure,
 	 * or memory manager initialization failure, it must
@@ -206,6 +206,15 @@
 			adev->runpm = true;
 			break;
 		}
+		/* XXX: disable runtime pm if we are the primary adapter
+		 * to avoid displays being re-enabled after DPMS.
+		 * This needs to be sorted out and fixed properly.
+		 */
+		if (adev->is_fw_fb)
+			adev->runpm = false;
+
+		amdgpu_runtime_pm_quirk(adev);
+
 		if (adev->runpm)
 			dev_info(adev->dev, "Using BACO for runtime pm\n");
 	}
@@ -573,6 +582,7 @@
 			crtc = (struct drm_crtc *)minfo->crtcs[i];
 			if (crtc && crtc->base.id == info->mode_crtc.id) {
 				struct amdgpu_crtc *amdgpu_crtc = to_amdgpu_crtc(crtc);
+
 				ui32 = amdgpu_crtc->crtc_id;
 				found = 1;
 				break;
@@ -591,7 +601,7 @@
 		if (ret)
 			return ret;
 
-		ret = copy_to_user(out, &ip, min((size_t)size, sizeof(ip)));
+		ret = copy_to_user(out, &ip, min_t(size_t, size, sizeof(ip)));
 		return ret ? -EFAULT : 0;
 	}
 	case AMDGPU_INFO_HW_IP_COUNT: {
@@ -739,17 +749,18 @@
 				    ? -EFAULT : 0;
 	}
 	case AMDGPU_INFO_READ_MMR_REG: {
-		unsigned n, alloc_size;
+		unsigned int n, alloc_size;
 		uint32_t *regs;
-		unsigned se_num = (info->read_mmr_reg.instance >>
+		unsigned int se_num = (info->read_mmr_reg.instance >>
 				   AMDGPU_INFO_MMR_SE_INDEX_SHIFT) &
 				  AMDGPU_INFO_MMR_SE_INDEX_MASK;
-		unsigned sh_num = (info->read_mmr_reg.instance >>
+		unsigned int sh_num = (info->read_mmr_reg.instance >>
 				   AMDGPU_INFO_MMR_SH_INDEX_SHIFT) &
 				  AMDGPU_INFO_MMR_SH_INDEX_MASK;
 
 		/* set full masks if the userspace set all bits
-		 * in the bitfields */
+		 * in the bitfields
+		 */
 		if (se_num == AMDGPU_INFO_MMR_SE_INDEX_MASK)
 			se_num = 0xffffffff;
 		else if (se_num >= AMDGPU_GFX_MAX_SE)
@@ -873,7 +884,7 @@
 		return ret;
 	}
 	case AMDGPU_INFO_VCE_CLOCK_TABLE: {
-		unsigned i;
+		unsigned int i;
 		struct drm_amdgpu_info_vce_clock_table vce_clk_table = {};
 		struct amd_vce_state *vce_state;
 
@@ -915,12 +926,17 @@
 			struct atom_context *atom_context;
 
 			atom_context = adev->mode_info.atom_context;
-			memcpy(vbios_info.name, atom_context->name, sizeof(atom_context->name));
-			memcpy(vbios_info.vbios_pn, atom_context->vbios_pn, sizeof(atom_context->vbios_pn));
-			vbios_info.version = atom_context->version;
-			memcpy(vbios_info.vbios_ver_str, atom_context->vbios_ver_str,
-						sizeof(atom_context->vbios_ver_str));
-			memcpy(vbios_info.date, atom_context->date, sizeof(atom_context->date));
+			if (atom_context) {
+				memcpy(vbios_info.name, atom_context->name,
+				       sizeof(atom_context->name));
+				memcpy(vbios_info.vbios_pn, atom_context->vbios_pn,
+				       sizeof(atom_context->vbios_pn));
+				vbios_info.version = atom_context->version;
+				memcpy(vbios_info.vbios_ver_str, atom_context->vbios_ver_str,
+				       sizeof(atom_context->vbios_ver_str));
+				memcpy(vbios_info.date, atom_context->date,
+				       sizeof(atom_context->date));
+			}
 
 			return copy_to_user(out, &vbios_info,
 						min((size_t)size, sizeof(vbios_info))) ? -EFAULT : 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_object.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_object.c
@@ -78,9 +78,10 @@
 static void amdgpu_bo_vm_destroy(struct ttm_buffer_object *tbo)
 {
 	struct amdgpu_device *adev = amdgpu_ttm_adev(tbo->bdev);
-	struct amdgpu_bo *bo = ttm_to_amdgpu_bo(tbo);
+	struct amdgpu_bo *shadow_bo = ttm_to_amdgpu_bo(tbo), *bo;
 	struct amdgpu_bo_vm *vmbo;
 
+	bo = shadow_bo->parent;
 	vmbo = to_amdgpu_bo_vm(bo);
 	/* in case amdgpu_device_recover_vram got NULL of bo->parent */
 	if (!list_empty(&vmbo->shadow_list)) {
@@ -684,13 +685,11 @@
 	 * num of amdgpu_vm_pt entries.
 	 */
 	BUG_ON(bp->bo_ptr_size < sizeof(struct amdgpu_bo_vm));
-	bp->destroy = &amdgpu_bo_vm_destroy;
 	r = amdgpu_bo_create(adev, bp, &bo_ptr);
 	if (r)
 		return r;
 
 	*vmbo_ptr = to_amdgpu_bo_vm(bo_ptr);
-	INIT_LIST_HEAD(&(*vmbo_ptr)->shadow_list);
 	return r;
 }
 
@@ -741,6 +740,8 @@
 
 	mutex_lock(&adev->shadow_list_lock);
 	list_add_tail(&vmbo->shadow_list, &adev->shadow_list);
+	vmbo->shadow->parent = amdgpu_bo_ref(&vmbo->bo);
+	vmbo->shadow->tbo.destroy = &amdgpu_bo_vm_destroy;
 	mutex_unlock(&adev->shadow_list_lock);
 }
 
@@ -912,6 +913,10 @@
 	if (WARN_ON_ONCE(min_offset > max_offset))
 		return -EINVAL;
 
+	/* Check domain to be pinned to against preferred domains */
+	if (bo->preferred_domains & domain)
+		domain = bo->preferred_domains & domain;
+
 	/* A shared bo cannot be migrated to VRAM */
 	if (bo->tbo.base.import_attach) {
 		if (domain & AMDGPU_GEM_DOMAIN_GTT)
@@ -1038,29 +1043,6 @@
 	}
 }
 
-/**
- * amdgpu_bo_evict_vram - evict VRAM buffers
- * @adev: amdgpu device object
- *
- * Evicts all VRAM buffers on the lru list of the memory type.
- * Mainly used for evicting vram at suspend time.
- *
- * Returns:
- * 0 for success or a negative error code on failure.
- */
-int amdgpu_bo_evict_vram(struct amdgpu_device *adev)
-{
-	struct ttm_resource_manager *man;
-
-	if (adev->in_s3 && (adev->flags & AMD_IS_APU)) {
-		/* No need to evict vram on APUs for suspend to ram */
-		return 0;
-	}
-
-	man = ttm_manager_type(&adev->mman.bdev, TTM_PL_VRAM);
-	return ttm_resource_manager_evict_all(&adev->mman.bdev, man);
-}
-
 static const char *amdgpu_vram_names[] = {
 	"UNKNOWN",
 	"GDDR1",
@@ -1254,19 +1236,15 @@
  * amdgpu_bo_move_notify - notification about a memory move
  * @bo: pointer to a buffer object
  * @evict: if this move is evicting the buffer from the graphics address space
- * @new_mem: new information of the bufer object
  *
  * Marks the corresponding &amdgpu_bo buffer object as invalid, also performs
  * bookkeeping.
  * TTM driver callback which is called when ttm moves a buffer.
  */
-void amdgpu_bo_move_notify(struct ttm_buffer_object *bo,
-			   bool evict,
-			   struct ttm_resource *new_mem)
+void amdgpu_bo_move_notify(struct ttm_buffer_object *bo, bool evict)
 {
 	struct amdgpu_device *adev = amdgpu_ttm_adev(bo->bdev);
 	struct amdgpu_bo *abo;
-	struct ttm_resource *old_mem = bo->resource;
 
 	if (!amdgpu_bo_is_amdgpu_bo(bo))
 		return;
@@ -1283,13 +1261,6 @@
 	/* remember the eviction */
 	if (evict)
 		atomic64_inc(&adev->num_evictions);
-
-	/* update statistics */
-	if (!new_mem)
-		return;
-
-	/* move_notify is called before move happens */
-	trace_amdgpu_bo_move(abo, new_mem->mem_type, old_mem->mem_type);
 }
 
 void amdgpu_bo_get_memory(struct amdgpu_bo *bo, uint64_t *vram_mem,
@@ -1343,7 +1314,8 @@
 	    !(abo->flags & AMDGPU_GEM_CREATE_VRAM_WIPE_ON_RELEASE))
 		return;
 
-	dma_resv_lock(bo->base.resv, NULL);
+	if (WARN_ON_ONCE(!dma_resv_trylock(bo->base.resv)))
+		return;
 
 	r = amdgpu_fill_buffer(abo, AMDGPU_POISON, bo->base.resv, &fence);
 	if (!WARN_ON(r)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_object.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_object.h
@@ -221,7 +221,7 @@
 	struct amdgpu_device *adev = amdgpu_ttm_adev(bo->tbo.bdev);
 	struct amdgpu_res_cursor cursor;
 
-	if (bo->tbo.resource->mem_type != TTM_PL_VRAM)
+	if (!bo->tbo.resource || bo->tbo.resource->mem_type != TTM_PL_VRAM)
 		return false;
 
 	amdgpu_res_first(bo->tbo.resource, 0, amdgpu_bo_size(bo), &cursor);
@@ -304,7 +304,6 @@
 int amdgpu_bo_pin_restricted(struct amdgpu_bo *bo, u32 domain,
 			     u64 min_offset, u64 max_offset);
 void amdgpu_bo_unpin(struct amdgpu_bo *bo);
-int amdgpu_bo_evict_vram(struct amdgpu_device *adev);
 int amdgpu_bo_init(struct amdgpu_device *adev);
 void amdgpu_bo_fini(struct amdgpu_device *adev);
 int amdgpu_bo_set_tiling_flags(struct amdgpu_bo *bo, u64 tiling_flags);
@@ -314,9 +313,7 @@
 int amdgpu_bo_get_metadata(struct amdgpu_bo *bo, void *buffer,
 			   size_t buffer_size, uint32_t *metadata_size,
 			   uint64_t *flags);
-void amdgpu_bo_move_notify(struct ttm_buffer_object *bo,
-			   bool evict,
-			   struct ttm_resource *new_mem);
+void amdgpu_bo_move_notify(struct ttm_buffer_object *bo, bool evict);
 void amdgpu_bo_release_notify(struct ttm_buffer_object *bo);
 vm_fault_t amdgpu_bo_fault_reserve_notify(struct ttm_buffer_object *bo);
 void amdgpu_bo_fence(struct amdgpu_bo *bo, struct dma_fence *fence,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_preempt_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_preempt_mgr.c
@@ -95,6 +95,7 @@
 	struct amdgpu_preempt_mgr *mgr = to_preempt_mgr(man);
 
 	atomic64_sub(res->num_pages, &mgr->used);
+	ttm_resource_fini(man, res);
 	kfree(res);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c
@@ -314,7 +314,39 @@
 		}
 	}
 
+	ret = amdgpu_bo_create_kernel(adev, PSP_1_MEG, PSP_1_MEG,
+				      amdgpu_sriov_vf(adev) ?
+				      AMDGPU_GEM_DOMAIN_VRAM : AMDGPU_GEM_DOMAIN_GTT,
+				      &psp->fw_pri_bo,
+				      &psp->fw_pri_mc_addr,
+				      &psp->fw_pri_buf);
+	if (ret)
+		return ret;
+
+	ret = amdgpu_bo_create_kernel(adev, PSP_FENCE_BUFFER_SIZE, PAGE_SIZE,
+				      AMDGPU_GEM_DOMAIN_VRAM,
+				      &psp->fence_buf_bo,
+				      &psp->fence_buf_mc_addr,
+				      &psp->fence_buf);
+	if (ret)
+		goto failed1;
+
+	ret = amdgpu_bo_create_kernel(adev, PSP_CMD_BUFFER_SIZE, PAGE_SIZE,
+				      AMDGPU_GEM_DOMAIN_VRAM,
+				      &psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
+				      (void **)&psp->cmd_buf_mem);
+	if (ret)
+		goto failed2;
+
 	return 0;
+
+failed2:
+	amdgpu_bo_free_kernel(&psp->fence_buf_bo,
+			      &psp->fence_buf_mc_addr, &psp->fence_buf);
+failed1:
+	amdgpu_bo_free_kernel(&psp->fw_pri_bo,
+			      &psp->fw_pri_mc_addr, &psp->fw_pri_buf);
+	return ret;
 }
 
 static int psp_sw_fini(void *handle)
@@ -344,6 +376,13 @@
 	kfree(cmd);
 	cmd = NULL;
 
+	amdgpu_bo_free_kernel(&psp->fw_pri_bo,
+			      &psp->fw_pri_mc_addr, &psp->fw_pri_buf);
+	amdgpu_bo_free_kernel(&psp->fence_buf_bo,
+			      &psp->fence_buf_mc_addr, &psp->fence_buf);
+	amdgpu_bo_free_kernel(&psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
+			      (void **)&psp->cmd_buf_mem);
+
 	return 0;
 }
 
@@ -1139,6 +1178,9 @@
 	uint8_t dst_num_links = node_info.num_links;
 
 	hive = amdgpu_get_xgmi_hive(psp->adev);
+	if (WARN_ON(!hive))
+		return;
+
 	list_for_each_entry(mirror_adev, &hive->device_list, gmc.xgmi.head) {
 		struct psp_xgmi_topology_info *mirror_top_info;
 		int j;
@@ -2207,12 +2249,16 @@
 		return ret;
 	}
 
+	if (amdgpu_sriov_vf(adev) && amdgpu_in_reset(adev))
+		goto skip_pin_bo;
+
 	ret = psp_tmr_init(psp);
 	if (ret) {
 		DRM_ERROR("PSP tmr init failed!\n");
 		return ret;
 	}
 
+skip_pin_bo:
 	/*
 	 * For ASICs with DF Cstate management centralized
 	 * to PMFW, TMR setup should be performed after PMFW
@@ -2462,7 +2508,7 @@
 static bool fw_load_skip_check(struct psp_context *psp,
 			       struct amdgpu_firmware_info *ucode)
 {
-	if (!ucode->fw)
+	if (!ucode->fw || !ucode->ucode_size)
 		return true;
 
 	if (ucode->ucode_id == AMDGPU_UCODE_ID_SMC &&
@@ -2576,51 +2622,18 @@
 	struct psp_context *psp = &adev->psp;
 
 	if (amdgpu_sriov_vf(adev) && amdgpu_in_reset(adev)) {
-		psp_ring_stop(psp, PSP_RING_TYPE__KM); /* should not destroy ring, only stop */
-		goto skip_memalloc;
-	}
-
-	if (amdgpu_sriov_vf(adev)) {
-		ret = amdgpu_bo_create_kernel(adev, PSP_1_MEG, PSP_1_MEG,
-						AMDGPU_GEM_DOMAIN_VRAM,
-						&psp->fw_pri_bo,
-						&psp->fw_pri_mc_addr,
-						&psp->fw_pri_buf);
+		/* should not destroy ring, only stop */
+		psp_ring_stop(psp, PSP_RING_TYPE__KM);
 	} else {
-		ret = amdgpu_bo_create_kernel(adev, PSP_1_MEG, PSP_1_MEG,
-						AMDGPU_GEM_DOMAIN_GTT,
-						&psp->fw_pri_bo,
-						&psp->fw_pri_mc_addr,
-						&psp->fw_pri_buf);
-	}
-
-	if (ret)
-		goto failed;
+		memset(psp->fence_buf, 0, PSP_FENCE_BUFFER_SIZE);
 
-	ret = amdgpu_bo_create_kernel(adev, PSP_FENCE_BUFFER_SIZE, PAGE_SIZE,
-					AMDGPU_GEM_DOMAIN_VRAM,
-					&psp->fence_buf_bo,
-					&psp->fence_buf_mc_addr,
-					&psp->fence_buf);
-	if (ret)
-		goto failed;
-
-	ret = amdgpu_bo_create_kernel(adev, PSP_CMD_BUFFER_SIZE, PAGE_SIZE,
-				      AMDGPU_GEM_DOMAIN_VRAM,
-				      &psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
-				      (void **)&psp->cmd_buf_mem);
-	if (ret)
-		goto failed;
-
-	memset(psp->fence_buf, 0, PSP_FENCE_BUFFER_SIZE);
-
-	ret = psp_ring_init(psp, PSP_RING_TYPE__KM);
-	if (ret) {
-		DRM_ERROR("PSP ring init failed!\n");
-		goto failed;
+		ret = psp_ring_init(psp, PSP_RING_TYPE__KM);
+		if (ret) {
+			DRM_ERROR("PSP ring init failed!\n");
+			goto failed;
+		}
 	}
 
-skip_memalloc:
 	ret = psp_hw_start(psp);
 	if (ret)
 		goto failed;
@@ -2719,6 +2732,9 @@
 		psp_rap_terminate(psp);
 		psp_dtm_terminate(psp);
 		psp_hdcp_terminate(psp);
+
+		if (adev->gmc.xgmi.num_physical_nodes > 1)
+			psp_xgmi_terminate(psp);
 	}
 
 	psp_asd_unload(psp);
@@ -2726,13 +2742,6 @@
 	psp_tmr_terminate(psp);
 	psp_ring_destroy(psp, PSP_RING_TYPE__KM);
 
-	amdgpu_bo_free_kernel(&psp->fw_pri_bo,
-			      &psp->fw_pri_mc_addr, &psp->fw_pri_buf);
-	amdgpu_bo_free_kernel(&psp->fence_buf_bo,
-			      &psp->fence_buf_mc_addr, &psp->fence_buf);
-	amdgpu_bo_free_kernel(&psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
-			      (void **)&psp->cmd_buf_mem);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c
@@ -820,6 +820,9 @@
 	if (!obj)
 		return -EINVAL;
 
+	if (!info || info->head.block == AMDGPU_RAS_BLOCK_COUNT)
+		return -EINVAL;
+
 	switch (info->head.block) {
 	case AMDGPU_RAS_BLOCK__UMC:
 		if (adev->umc.ras_funcs &&
@@ -1192,7 +1195,8 @@
 {
 	struct amdgpu_ras *con = amdgpu_ras_get_context(adev);
 
-	sysfs_remove_file_from_group(&adev->dev->kobj,
+	if (adev->dev->kobj.sd)
+		sysfs_remove_file_from_group(&adev->dev->kobj,
 				&con->badpages_attr.attr,
 				RAS_FS_NAME);
 }
@@ -1209,7 +1213,8 @@
 		.attrs = attrs,
 	};
 
-	sysfs_remove_group(&adev->dev->kobj, &group);
+	if (adev->dev->kobj.sd)
+		sysfs_remove_group(&adev->dev->kobj, &group);
 
 	return 0;
 }
@@ -1257,7 +1262,8 @@
 	if (!obj || !obj->attr_inuse)
 		return -EINVAL;
 
-	sysfs_remove_file_from_group(&adev->dev->kobj,
+	if (adev->dev->kobj.sd)
+		sysfs_remove_file_from_group(&adev->dev->kobj,
 				&obj->sysfs_attr.attr,
 				RAS_FS_NAME);
 	obj->attr_inuse = 0;
@@ -1503,12 +1509,15 @@
 int amdgpu_ras_interrupt_dispatch(struct amdgpu_device *adev,
 		struct ras_dispatch_if *info)
 {
-	struct ras_manager *obj = amdgpu_ras_find_obj(adev, &info->head);
-	struct ras_ih_data *data = &obj->ih_data;
+	struct ras_manager *obj;
+	struct ras_ih_data *data;
 
+	obj = amdgpu_ras_find_obj(adev, &info->head);
 	if (!obj)
 		return -EINVAL;
 
+	data = &obj->ih_data;
+
 	if (data->inuse == 0)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ring.c
@@ -263,7 +263,7 @@
 	ring->max_dw = max_dw;
 	ring->hw_prio = hw_prio;
 
-	if (!ring->no_scheduler) {
+	if (!ring->no_scheduler && ring->funcs->type < AMDGPU_HW_IP_NUM) {
 		hw_ip = ring->funcs->type;
 		num_sched = &adev->gpu_sched[hw_ip][hw_prio].num_scheds;
 		adev->gpu_sched[hw_ip][hw_prio].sched[(*num_sched)++] =
@@ -367,8 +367,9 @@
 					size_t size, loff_t *pos)
 {
 	struct amdgpu_ring *ring = file_inode(f)->i_private;
-	int r, i;
 	uint32_t value, result, early[3];
+	loff_t i;
+	int r;
 
 	if (*pos & 3 || size & 3)
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_sched.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_sched.c
@@ -66,6 +66,7 @@
 {
 	struct fd f = fdget(fd);
 	struct amdgpu_fpriv *fpriv;
+	struct amdgpu_ctx_mgr *mgr;
 	struct amdgpu_ctx *ctx;
 	uint32_t id;
 	int r;
@@ -79,8 +80,11 @@
 		return r;
 	}
 
-	idr_for_each_entry(&fpriv->ctx_mgr.ctx_handles, ctx, id)
+	mgr = &fpriv->ctx_mgr;
+	mutex_lock(&mgr->lock);
+	idr_for_each_entry(&mgr->ctx_handles, ctx, id)
 		amdgpu_ctx_priority_override(ctx, priority);
+	mutex_unlock(&mgr->lock);
 
 	fdput(f);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_sync.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_sync.c
@@ -208,7 +208,8 @@
 
 	/* Never sync to VM updates either. */
 	if (fence_owner == AMDGPU_FENCE_OWNER_VM &&
-	    owner != AMDGPU_FENCE_OWNER_UNDEFINED)
+	    owner != AMDGPU_FENCE_OWNER_UNDEFINED &&
+	    owner != AMDGPU_FENCE_OWNER_KFD)
 		return false;
 
 	/* Ignore fences depending on the sync mode */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.c
@@ -554,10 +554,11 @@
 			return r;
 	}
 
+	trace_amdgpu_bo_move(abo, new_mem->mem_type, old_mem->mem_type);
 out:
 	/* update statistics */
 	atomic64_add(bo->base.size, &adev->num_bytes_moved);
-	amdgpu_bo_move_notify(bo, evict, new_mem);
+	amdgpu_bo_move_notify(bo, evict);
 	return 0;
 }
 
@@ -774,7 +775,7 @@
 	/* Map SG to device */
 	r = dma_map_sgtable(adev->dev, ttm->sg, direction, 0);
 	if (r)
-		goto release_sg;
+		goto release_sg_table;
 
 	/* convert SG to linear array of pages and dma addresses */
 	drm_prime_sg_to_dma_addr_array(ttm->sg, gtt->ttm.dma_address,
@@ -782,6 +783,8 @@
 
 	return 0;
 
+release_sg_table:
+	sg_free_table(ttm->sg);
 release_sg:
 	kfree(ttm->sg);
 	ttm->sg = NULL;
@@ -858,6 +861,7 @@
 		r = amdgpu_gart_bind(adev, gtt->offset, ttm->num_pages,
 				     gtt->ttm.dma_address, flags);
 	}
+	gtt->bound = true;
 
 gart_bind_fail:
 	if (r)
@@ -1480,7 +1484,7 @@
 static void
 amdgpu_bo_delete_mem_notify(struct ttm_buffer_object *bo)
 {
-	amdgpu_bo_move_notify(bo, false, NULL);
+	amdgpu_bo_move_notify(bo, false);
 }
 
 static struct ttm_device_funcs amdgpu_bo_driver = {
@@ -1660,6 +1664,7 @@
 
 	mutex_init(&adev->mman.gtt_window_lock);
 
+	dma_set_max_seg_size(adev->dev, UINT_MAX);
 	/* No others user of address space so set it to 0 */
 	r = ttm_device_init(&adev->mman.bdev, &amdgpu_bo_driver, adev->dev,
 			       adev_to_drm(adev)->anon_inode->i_mapping,
@@ -1892,7 +1897,7 @@
 	unsigned i;
 	int r;
 
-	if (direct_submit && !ring->sched.ready) {
+	if (!direct_submit && !ring->sched.ready) {
 		DRM_ERROR("Trying to move memory with ring turned off.\n");
 		return -EINVAL;
 	}
@@ -2036,6 +2041,36 @@
 	return r;
 }
 
+/**
+ * amdgpu_ttm_evict_resources - evict memory buffers
+ * @adev: amdgpu device object
+ * @mem_type: evicted BO's memory type
+ *
+ * Evicts all @mem_type buffers on the lru list of the memory type.
+ *
+ * Returns:
+ * 0 for success or a negative error code on failure.
+ */
+int amdgpu_ttm_evict_resources(struct amdgpu_device *adev, int mem_type)
+{
+	struct ttm_resource_manager *man;
+
+	switch (mem_type) {
+	case TTM_PL_VRAM:
+	case TTM_PL_TT:
+	case AMDGPU_PL_GWS:
+	case AMDGPU_PL_GDS:
+	case AMDGPU_PL_OA:
+		man = ttm_manager_type(&adev->mman.bdev, mem_type);
+		break;
+	default:
+		DRM_ERROR("Trying to evict invalid memory type\n");
+		return -EINVAL;
+	}
+
+	return ttm_resource_manager_evict_all(&adev->mman.bdev, man);
+}
+
 #if defined(CONFIG_DEBUG_FS)
 
 static int amdgpu_mm_vram_table_show(struct seq_file *m, void *unused)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.h
@@ -190,6 +190,7 @@
 uint64_t amdgpu_ttm_tt_pde_flags(struct ttm_tt *ttm, struct ttm_resource *mem);
 uint64_t amdgpu_ttm_tt_pte_flags(struct amdgpu_device *adev, struct ttm_tt *ttm,
 				 struct ttm_resource *mem);
+int amdgpu_ttm_evict_resources(struct amdgpu_device *adev, int mem_type);
 
 void amdgpu_ttm_debugfs_init(struct amdgpu_device *adev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c
@@ -723,8 +723,7 @@
 
 void amdgpu_ucode_free_bo(struct amdgpu_device *adev)
 {
-	if (adev->firmware.load_type != AMDGPU_FW_LOAD_DIRECT)
-		amdgpu_bo_free_kernel(&adev->firmware.fw_buf,
+	amdgpu_bo_free_kernel(&adev->firmware.fw_buf,
 		&adev->firmware.fw_buf_mc,
 		&adev->firmware.fw_buf_ptr);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c
@@ -220,15 +220,15 @@
 
 	drm_sched_entity_destroy(&adev->vce.entity);
 
-	amdgpu_bo_free_kernel(&adev->vce.vcpu_bo, &adev->vce.gpu_addr,
-		(void **)&adev->vce.cpu_addr);
-
 	for (i = 0; i < adev->vce.num_rings; i++)
 		amdgpu_ring_fini(&adev->vce.ring[i]);
 
 	release_firmware(adev->vce.fw);
 	mutex_destroy(&adev->vce.idle_mutex);
 
+	amdgpu_bo_free_kernel(&adev->vce.vcpu_bo, &adev->vce.gpu_addr,
+		(void **)&adev->vce.cpu_addr);
+
 	return 0;
 }
 
@@ -733,7 +733,8 @@
 	uint32_t created = 0;
 	uint32_t allocated = 0;
 	uint32_t tmp, handle = 0;
-	uint32_t *size = &tmp;
+	uint32_t dummy = 0xffffffff;
+	uint32_t *size = &dummy;
 	unsigned idx;
 	int i, r = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_vcn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_vcn.c
@@ -149,6 +149,9 @@
 		break;
 	case CHIP_VANGOGH:
 		fw_name = FIRMWARE_VANGOGH;
+		if ((adev->firmware.load_type == AMDGPU_FW_LOAD_PSP) &&
+		    (adev->pg_flags & AMD_PG_SUPPORT_VCN_DPG))
+			adev->vcn.indirect_sram = true;
 		break;
 	case CHIP_DIMGREY_CAVEFISH:
 		fw_name = FIRMWARE_DIMGREY_CAVEFISH;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_virt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_virt.c
@@ -24,6 +24,7 @@
 #include <linux/module.h>
 
 #include <drm/drm_drv.h>
+#include <xen/xen.h>
 
 #include "amdgpu.h"
 #include "amdgpu_ras.h"
@@ -121,8 +122,10 @@
 
 	if (virt->ops && virt->ops->req_full_gpu) {
 		r = virt->ops->req_full_gpu(adev, init);
-		if (r)
+		if (r) {
+			adev->no_hw_access = true;
 			return r;
+		}
 
 		adev->virt.caps &= ~AMDGPU_SRIOV_CAPS_RUNTIME;
 	}
@@ -409,6 +412,8 @@
 	uint64_t retired_page;
 	uint32_t bp_idx, bp_cnt;
 
+	memset(&bp, 0, sizeof(bp));
+
 	if (bp_block_size) {
 		bp_cnt = bp_block_size / sizeof(uint64_t);
 		for (bp_idx = 0; bp_idx < bp_cnt; bp_idx++) {
@@ -583,7 +588,7 @@
 
 	vf2pf_info->checksum =
 		amd_sriov_msg_checksum(
-		vf2pf_info, vf2pf_info->header.size, 0, 0);
+		vf2pf_info, sizeof(*vf2pf_info), 0, 0);
 
 	return 0;
 }
@@ -613,16 +618,34 @@
 
 void amdgpu_virt_init_data_exchange(struct amdgpu_device *adev)
 {
-	uint64_t bp_block_offset = 0;
-	uint32_t bp_block_size = 0;
-	struct amd_sriov_msg_pf2vf_info *pf2vf_v2 = NULL;
-
 	adev->virt.fw_reserve.p_pf2vf = NULL;
 	adev->virt.fw_reserve.p_vf2pf = NULL;
 	adev->virt.vf2pf_update_interval_ms = 0;
 
 	if (adev->mman.fw_vram_usage_va != NULL) {
-		adev->virt.vf2pf_update_interval_ms = 2000;
+		/* go through this logic in ip_init and reset to init workqueue*/
+		amdgpu_virt_exchange_data(adev);
+
+		INIT_DELAYED_WORK(&adev->virt.vf2pf_work, amdgpu_virt_update_vf2pf_work_item);
+		schedule_delayed_work(&(adev->virt.vf2pf_work), msecs_to_jiffies(adev->virt.vf2pf_update_interval_ms));
+	} else if (adev->bios != NULL) {
+		/* got through this logic in early init stage to get necessary flags, e.g. rlcg_acc related*/
+		adev->virt.fw_reserve.p_pf2vf =
+			(struct amd_sriov_msg_pf2vf_info_header *)
+			(adev->bios + (AMD_SRIOV_MSG_PF2VF_OFFSET_KB << 10));
+
+		amdgpu_virt_read_pf2vf_data(adev);
+	}
+}
+
+
+void amdgpu_virt_exchange_data(struct amdgpu_device *adev)
+{
+	uint64_t bp_block_offset = 0;
+	uint32_t bp_block_size = 0;
+	struct amd_sriov_msg_pf2vf_info *pf2vf_v2 = NULL;
+
+	if (adev->mman.fw_vram_usage_va != NULL) {
 
 		adev->virt.fw_reserve.p_pf2vf =
 			(struct amd_sriov_msg_pf2vf_info_header *)
@@ -648,22 +671,10 @@
 				if (adev->virt.ras_init_done)
 					amdgpu_virt_add_bad_page(adev, bp_block_offset, bp_block_size);
 			}
-	} else if (adev->bios != NULL) {
-		adev->virt.fw_reserve.p_pf2vf =
-			(struct amd_sriov_msg_pf2vf_info_header *)
-			(adev->bios + (AMD_SRIOV_MSG_PF2VF_OFFSET_KB << 10));
-
-		amdgpu_virt_read_pf2vf_data(adev);
-
-		return;
-	}
-
-	if (adev->virt.vf2pf_update_interval_ms != 0) {
-		INIT_DELAYED_WORK(&adev->virt.vf2pf_work, amdgpu_virt_update_vf2pf_work_item);
-		schedule_delayed_work(&(adev->virt.vf2pf_work), adev->virt.vf2pf_update_interval_ms);
 	}
 }
 
+
 void amdgpu_detect_virtualization(struct amdgpu_device *adev)
 {
 	uint32_t reg;
@@ -694,10 +705,17 @@
 		adev->virt.caps |= AMDGPU_SRIOV_CAPS_ENABLE_IOV;
 
 	if (!reg) {
-		if (is_virtual_machine())	/* passthrough mode exclus sriov mod */
+		/* passthrough mode exclus sriov mod */
+		if (is_virtual_machine() && !xen_initial_domain())
 			adev->virt.caps |= AMDGPU_PASSTHROUGH_MODE;
 	}
 
+	if (amdgpu_sriov_vf(adev) && adev->asic_type == CHIP_SIENNA_CICHLID)
+		/* VF MMIO access (except mailbox range) from CPU
+		 * will be blocked during sriov runtime
+		 */
+		adev->virt.caps |= AMDGPU_VF_MMIO_ACCESS_PROTECT;
+
 	/* we have the ability to check now */
 	if (amdgpu_sriov_vf(adev)) {
 		switch (adev->asic_type) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_virt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_virt.h
@@ -31,6 +31,7 @@
 #define AMDGPU_SRIOV_CAPS_IS_VF        (1 << 2) /* this GPU is a virtual function */
 #define AMDGPU_PASSTHROUGH_MODE        (1 << 3) /* thw whole GPU is pass through for VM */
 #define AMDGPU_SRIOV_CAPS_RUNTIME      (1 << 4) /* is out of full access mode */
+#define AMDGPU_VF_MMIO_ACCESS_PROTECT  (1 << 5) /* MMIO write access is not allowed in sriov runtime */
 
 /* all asic after AI use this offset */
 #define mmRCC_IOV_FUNC_IDENTIFIER 0xDE5
@@ -61,6 +62,8 @@
 	uint64_t data[AMDGPU_VF_ERROR_ENTRY_SIZE];
 };
 
+enum idh_request;
+
 /**
  * struct amdgpu_virt_ops - amdgpu device virt operations
  */
@@ -70,7 +73,8 @@
 	int (*req_init_data)(struct amdgpu_device *adev);
 	int (*reset_gpu)(struct amdgpu_device *adev);
 	int (*wait_reset)(struct amdgpu_device *adev);
-	void (*trans_msg)(struct amdgpu_device *adev, u32 req, u32 data1, u32 data2, u32 data3);
+	void (*trans_msg)(struct amdgpu_device *adev, enum idh_request req,
+			  u32 data1, u32 data2, u32 data3);
 };
 
 /*
@@ -278,6 +282,9 @@
 #define amdgpu_passthrough(adev) \
 ((adev)->virt.caps & AMDGPU_PASSTHROUGH_MODE)
 
+#define amdgpu_sriov_vf_mmio_access_protection(adev) \
+((adev)->virt.caps & AMDGPU_VF_MMIO_ACCESS_PROTECT)
+
 static inline bool is_virtual_machine(void)
 {
 #ifdef CONFIG_X86
@@ -308,6 +315,7 @@
 void amdgpu_virt_free_mm_table(struct amdgpu_device *adev);
 void amdgpu_virt_release_ras_err_handler_data(struct amdgpu_device *adev);
 void amdgpu_virt_init_data_exchange(struct amdgpu_device *adev);
+void amdgpu_virt_exchange_data(struct amdgpu_device *adev);
 void amdgpu_virt_fini_data_exchange(struct amdgpu_device *adev);
 void amdgpu_detect_virtualization(struct amdgpu_device *adev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_vkms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_vkms.c
@@ -2,6 +2,7 @@
 
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_simple_kms_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
 #include <drm/drm_vblank.h>
 
 #include "amdgpu.h"
@@ -16,6 +17,8 @@
 #include "ivsrcid/ivsrcid_vislands30.h"
 #include "amdgpu_vkms.h"
 #include "amdgpu_display.h"
+#include "atom.h"
+#include "amdgpu_irq.h"
 
 /**
  * DOC: amdgpu_vkms
@@ -41,20 +44,20 @@
 
 static enum hrtimer_restart amdgpu_vkms_vblank_simulate(struct hrtimer *timer)
 {
-	struct amdgpu_vkms_output *output = container_of(timer,
-							 struct amdgpu_vkms_output,
-							 vblank_hrtimer);
-	struct drm_crtc *crtc = &output->crtc;
+	struct amdgpu_crtc *amdgpu_crtc = container_of(timer, struct amdgpu_crtc, vblank_timer);
+	struct drm_crtc *crtc = &amdgpu_crtc->base;
+	struct amdgpu_vkms_output *output = drm_crtc_to_amdgpu_vkms_output(crtc);
 	u64 ret_overrun;
 	bool ret;
 
-	ret_overrun = hrtimer_forward_now(&output->vblank_hrtimer,
+	ret_overrun = hrtimer_forward_now(&amdgpu_crtc->vblank_timer,
 					  output->period_ns);
 	WARN_ON(ret_overrun != 1);
 
 	ret = drm_crtc_handle_vblank(crtc);
+	/* Don't queue timer again when vblank is disabled. */
 	if (!ret)
-		DRM_ERROR("amdgpu_vkms failure on handling vblank");
+		return HRTIMER_NORESTART;
 
 	return HRTIMER_RESTART;
 }
@@ -65,22 +68,21 @@
 	unsigned int pipe = drm_crtc_index(crtc);
 	struct drm_vblank_crtc *vblank = &dev->vblank[pipe];
 	struct amdgpu_vkms_output *out = drm_crtc_to_amdgpu_vkms_output(crtc);
+	struct amdgpu_crtc *amdgpu_crtc = to_amdgpu_crtc(crtc);
 
 	drm_calc_timestamping_constants(crtc, &crtc->mode);
 
-	hrtimer_init(&out->vblank_hrtimer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
-	out->vblank_hrtimer.function = &amdgpu_vkms_vblank_simulate;
 	out->period_ns = ktime_set(0, vblank->framedur_ns);
-	hrtimer_start(&out->vblank_hrtimer, out->period_ns, HRTIMER_MODE_REL);
+	hrtimer_start(&amdgpu_crtc->vblank_timer, out->period_ns, HRTIMER_MODE_REL);
 
 	return 0;
 }
 
 static void amdgpu_vkms_disable_vblank(struct drm_crtc *crtc)
 {
-	struct amdgpu_vkms_output *out = drm_crtc_to_amdgpu_vkms_output(crtc);
+	struct amdgpu_crtc *amdgpu_crtc = to_amdgpu_crtc(crtc);
 
-	hrtimer_cancel(&out->vblank_hrtimer);
+	hrtimer_try_to_cancel(&amdgpu_crtc->vblank_timer);
 }
 
 static bool amdgpu_vkms_get_vblank_timestamp(struct drm_crtc *crtc,
@@ -92,13 +94,14 @@
 	unsigned int pipe = crtc->index;
 	struct amdgpu_vkms_output *output = drm_crtc_to_amdgpu_vkms_output(crtc);
 	struct drm_vblank_crtc *vblank = &dev->vblank[pipe];
+	struct amdgpu_crtc *amdgpu_crtc = to_amdgpu_crtc(crtc);
 
 	if (!READ_ONCE(vblank->enabled)) {
 		*vblank_time = ktime_get();
 		return true;
 	}
 
-	*vblank_time = READ_ONCE(output->vblank_hrtimer.node.expires);
+	*vblank_time = READ_ONCE(amdgpu_crtc->vblank_timer.node.expires);
 
 	if (WARN_ON(*vblank_time == vblank->time))
 		return true;
@@ -142,15 +145,16 @@
 static void amdgpu_vkms_crtc_atomic_flush(struct drm_crtc *crtc,
 					  struct drm_atomic_state *state)
 {
+	unsigned long flags;
 	if (crtc->state->event) {
-		spin_lock(&crtc->dev->event_lock);
+		spin_lock_irqsave(&crtc->dev->event_lock, flags);
 
 		if (drm_crtc_vblank_get(crtc) != 0)
 			drm_crtc_send_vblank_event(crtc, crtc->state->event);
 		else
 			drm_crtc_arm_vblank_event(crtc, crtc->state->event);
 
-		spin_unlock(&crtc->dev->event_lock);
+		spin_unlock_irqrestore(&crtc->dev->event_lock, flags);
 
 		crtc->state->event = NULL;
 	}
@@ -165,6 +169,8 @@
 static int amdgpu_vkms_crtc_init(struct drm_device *dev, struct drm_crtc *crtc,
 			  struct drm_plane *primary, struct drm_plane *cursor)
 {
+	struct amdgpu_device *adev = drm_to_adev(dev);
+	struct amdgpu_crtc *amdgpu_crtc = to_amdgpu_crtc(crtc);
 	int ret;
 
 	ret = drm_crtc_init_with_planes(dev, crtc, primary, cursor,
@@ -176,6 +182,17 @@
 
 	drm_crtc_helper_add(crtc, &amdgpu_vkms_crtc_helper_funcs);
 
+	amdgpu_crtc->crtc_id = drm_crtc_index(crtc);
+	adev->mode_info.crtcs[drm_crtc_index(crtc)] = amdgpu_crtc;
+
+	amdgpu_crtc->pll_id = ATOM_PPLL_INVALID;
+	amdgpu_crtc->encoder = NULL;
+	amdgpu_crtc->connector = NULL;
+	amdgpu_crtc->vsync_timer_enabled = AMDGPU_IRQ_STATE_DISABLE;
+
+	hrtimer_init(&amdgpu_crtc->vblank_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+	amdgpu_crtc->vblank_timer.function = &amdgpu_vkms_vblank_simulate;
+
 	return ret;
 }
 
@@ -222,6 +239,8 @@
 
 	for (i = 0; i < ARRAY_SIZE(common_modes); i++) {
 		mode = drm_cvt_mode(dev, common_modes[i].w, common_modes[i].h, 60, false, false, false);
+		if (!mode)
+			continue;
 		drm_mode_probed_add(connector, mode);
 	}
 
@@ -297,7 +316,13 @@
 		return 0;
 	}
 	afb = to_amdgpu_framebuffer(new_state->fb);
-	obj = new_state->fb->obj[0];
+
+	obj = drm_gem_fb_get_obj(new_state->fb, 0);
+	if (!obj) {
+		DRM_ERROR("Failed to get obj from framebuffer\n");
+		return -EINVAL;
+	}
+
 	rbo = gem_to_amdgpu_bo(obj);
 	adev = amdgpu_ttm_adev(rbo->tbo.bdev);
 	INIT_LIST_HEAD(&list);
@@ -346,12 +371,19 @@
 				   struct drm_plane_state *old_state)
 {
 	struct amdgpu_bo *rbo;
+	struct drm_gem_object *obj;
 	int r;
 
 	if (!old_state->fb)
 		return;
 
-	rbo = gem_to_amdgpu_bo(old_state->fb->obj[0]);
+	obj = drm_gem_fb_get_obj(old_state->fb, 0);
+	if (!obj) {
+		DRM_ERROR("Failed to get obj from framebuffer\n");
+		return;
+	}
+
+	rbo = gem_to_amdgpu_bo(obj);
 	r = amdgpu_bo_reserve(rbo, false);
 	if (unlikely(r)) {
 		DRM_ERROR("failed to reserve rbo before unpin\n");
@@ -401,7 +433,7 @@
 {
 	struct drm_connector *connector = &output->connector;
 	struct drm_encoder *encoder = &output->encoder;
-	struct drm_crtc *crtc = &output->crtc;
+	struct drm_crtc *crtc = &output->crtc.base;
 	struct drm_plane *primary, *cursor = NULL;
 	int ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_vkms.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_vkms.h
@@ -10,15 +10,14 @@
 #define YRES_MAX  16384
 
 #define drm_crtc_to_amdgpu_vkms_output(target) \
-	container_of(target, struct amdgpu_vkms_output, crtc)
+	container_of(target, struct amdgpu_vkms_output, crtc.base)
 
 extern const struct amdgpu_ip_block_version amdgpu_vkms_ip_block;
 
 struct amdgpu_vkms_output {
-	struct drm_crtc crtc;
+	struct amdgpu_crtc crtc;
 	struct drm_encoder encoder;
 	struct drm_connector connector;
-	struct hrtimer vblank_hrtimer;
 	ktime_t period_ns;
 	struct drm_pending_vblank_event *event;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c
@@ -768,11 +768,17 @@
  * Check if all VM PDs/PTs are ready for updates
  *
  * Returns:
- * True if eviction list is empty.
+ * True if VM is not evicting.
  */
 bool amdgpu_vm_ready(struct amdgpu_vm *vm)
 {
-	return list_empty(&vm->evicted);
+	bool ret;
+
+	amdgpu_vm_eviction_lock(vm);
+	ret = !vm->evicting;
+	amdgpu_vm_eviction_unlock(vm);
+
+	return ret && list_empty(&vm->evicted);
 }
 
 /**
@@ -977,7 +983,6 @@
 		return r;
 	}
 
-	(*vmbo)->shadow->parent = amdgpu_bo_ref(bo);
 	amdgpu_bo_add_to_shadow_list(*vmbo);
 
 	return 0;
@@ -1953,10 +1958,9 @@
 	 * next command submission.
 	 */
 	if (bo && bo->tbo.base.resv == vm->root.bo->tbo.base.resv) {
-		uint32_t mem_type = bo->tbo.resource->mem_type;
-
-		if (!(bo->preferred_domains &
-		      amdgpu_mem_type_to_domain(mem_type)))
+		if (bo->tbo.resource &&
+		    !(bo->preferred_domains &
+		      amdgpu_mem_type_to_domain(bo->tbo.resource->mem_type)))
 			amdgpu_vm_bo_evicted(&bo_va->base);
 		else
 			amdgpu_vm_bo_idle(&bo_va->base);
@@ -2301,6 +2305,37 @@
 	trace_amdgpu_vm_bo_map(bo_va, mapping);
 }
 
+/* Validate operation parameters to prevent potential abuse */
+static int amdgpu_vm_verify_parameters(struct amdgpu_device *adev,
+					  struct amdgpu_bo *bo,
+					  uint64_t saddr,
+					  uint64_t offset,
+					  uint64_t size)
+{
+	uint64_t tmp, lpfn;
+
+	if (saddr & AMDGPU_GPU_PAGE_MASK
+	    || offset & AMDGPU_GPU_PAGE_MASK
+	    || size & AMDGPU_GPU_PAGE_MASK)
+		return -EINVAL;
+
+	if (check_add_overflow(saddr, size, &tmp)
+	    || check_add_overflow(offset, size, &tmp)
+	    || size == 0 /* which also leads to end < begin */)
+		return -EINVAL;
+
+	/* make sure object fit at this offset */
+	if (bo && offset + size > amdgpu_bo_size(bo))
+		return -EINVAL;
+
+	/* Ensure last pfn not exceed max_pfn */
+	lpfn = (saddr + size - 1) >> AMDGPU_GPU_PAGE_SHIFT;
+	if (lpfn >= adev->vm_manager.max_pfn)
+		return -EINVAL;
+
+	return 0;
+}
+
 /**
  * amdgpu_vm_bo_map - map bo inside a vm
  *
@@ -2327,21 +2362,14 @@
 	struct amdgpu_bo *bo = bo_va->base.bo;
 	struct amdgpu_vm *vm = bo_va->base.vm;
 	uint64_t eaddr;
+	int r;
 
-	/* validate the parameters */
-	if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK ||
-	    size == 0 || size & ~PAGE_MASK)
-		return -EINVAL;
-
-	/* make sure object fit at this offset */
-	eaddr = saddr + size - 1;
-	if (saddr >= eaddr ||
-	    (bo && offset + size > amdgpu_bo_size(bo)) ||
-	    (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT))
-		return -EINVAL;
+	r = amdgpu_vm_verify_parameters(adev, bo, saddr, offset, size);
+	if (r)
+		return r;
 
 	saddr /= AMDGPU_GPU_PAGE_SIZE;
-	eaddr /= AMDGPU_GPU_PAGE_SIZE;
+	eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE;
 
 	tmp = amdgpu_vm_it_iter_first(&vm->va, saddr, eaddr);
 	if (tmp) {
@@ -2394,17 +2422,9 @@
 	uint64_t eaddr;
 	int r;
 
-	/* validate the parameters */
-	if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK ||
-	    size == 0 || size & ~PAGE_MASK)
-		return -EINVAL;
-
-	/* make sure object fit at this offset */
-	eaddr = saddr + size - 1;
-	if (saddr >= eaddr ||
-	    (bo && offset + size > amdgpu_bo_size(bo)) ||
-	    (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT))
-		return -EINVAL;
+	r = amdgpu_vm_verify_parameters(adev, bo, saddr, offset, size);
+	if (r)
+		return r;
 
 	/* Allocate all the needed memory */
 	mapping = kmalloc(sizeof(*mapping), GFP_KERNEL);
@@ -2418,7 +2438,7 @@
 	}
 
 	saddr /= AMDGPU_GPU_PAGE_SIZE;
-	eaddr /= AMDGPU_GPU_PAGE_SIZE;
+	eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE;
 
 	mapping->start = saddr;
 	mapping->last = eaddr;
@@ -2505,10 +2525,14 @@
 	struct amdgpu_bo_va_mapping *before, *after, *tmp, *next;
 	LIST_HEAD(removed);
 	uint64_t eaddr;
+	int r;
+
+	r = amdgpu_vm_verify_parameters(adev, NULL, saddr, 0, size);
+	if (r)
+		return r;
 
-	eaddr = saddr + size - 1;
 	saddr /= AMDGPU_GPU_PAGE_SIZE;
-	eaddr /= AMDGPU_GPU_PAGE_SIZE;
+	eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE;
 
 	/* Allocate all the needed memory */
 	before = kzalloc(sizeof(*before), GFP_KERNEL);
@@ -2570,18 +2594,30 @@
 
 	/* Insert partial mapping before the range */
 	if (!list_empty(&before->list)) {
+		struct amdgpu_bo *bo = before->bo_va->base.bo;
+
 		amdgpu_vm_it_insert(before, &vm->va);
 		if (before->flags & AMDGPU_PTE_PRT)
 			amdgpu_vm_prt_get(adev);
+
+		if (bo && bo->tbo.base.resv == vm->root.bo->tbo.base.resv &&
+		    !before->bo_va->base.moved)
+			amdgpu_vm_bo_moved(&before->bo_va->base);
 	} else {
 		kfree(before);
 	}
 
 	/* Insert partial mapping after the range */
 	if (!list_empty(&after->list)) {
+		struct amdgpu_bo *bo = after->bo_va->base.bo;
+
 		amdgpu_vm_it_insert(after, &vm->va);
 		if (after->flags & AMDGPU_PTE_PRT)
 			amdgpu_vm_prt_get(adev);
+
+		if (bo && bo->tbo.base.resv == vm->root.bo->tbo.base.resv &&
+		    !after->bo_va->base.moved)
+			amdgpu_vm_bo_moved(&after->bo_va->base);
 	} else {
 		kfree(after);
 	}
@@ -3218,7 +3254,11 @@
 	 */
 #ifdef CONFIG_X86_64
 	if (amdgpu_vm_update_mode == -1) {
-		if (amdgpu_gmc_vram_full_visible(&adev->gmc))
+		/* For asic with VF MMIO access protection
+		 * avoid using CPU for VM table updates
+		 */
+		if (amdgpu_gmc_vram_full_visible(&adev->gmc) &&
+		    !amdgpu_sriov_vf_mmio_access_protection(adev))
 			adev->vm_manager.vm_update_mode =
 				AMDGPU_VM_USE_CPU_FOR_COMPUTE;
 		else
@@ -3265,6 +3305,10 @@
 	long timeout = msecs_to_jiffies(2000);
 	int r;
 
+	/* No valid flags defined yet */
+	if (args->in.flags)
+		return -EINVAL;
+
 	switch (args->in.op) {
 	case AMDGPU_VM_OP_RESERVE_VMID:
 		/* We only have requirement to reserve vmid from gfxhub */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_vram_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_vram_mgr.c
@@ -476,6 +476,7 @@
 	while (i--)
 		drm_mm_remove_node(&node->mm_nodes[i]);
 	spin_unlock(&mgr->lock);
+	ttm_resource_fini(man, &node->base);
 	kvfree(node);
 
 error_sub:
@@ -515,6 +516,7 @@
 	atomic64_sub(usage, &mgr->usage);
 	atomic64_sub(vis_usage, &mgr->vis_usage);
 
+	ttm_resource_fini(man, res);
 	kvfree(node);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/amdgpu_xgmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/amdgpu_xgmi.c
@@ -386,6 +386,7 @@
 			"%s", "xgmi_hive_info");
 	if (ret) {
 		dev_err(adev->dev, "XGMI: failed initializing kobject for xgmi hive\n");
+		kobject_put(&hive->kobj);
 		kfree(hive);
 		hive = NULL;
 		goto pro_end;
@@ -722,7 +723,7 @@
 		amdgpu_put_xgmi_hive(hive);
 	}
 
-	return psp_xgmi_terminate(&adev->psp);
+	return 0;
 }
 
 static int amdgpu_xgmi_ras_late_init(struct amdgpu_device *adev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/atom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/atom.c
@@ -311,7 +311,7 @@
 				DEBUG("IMM 0x%02X\n", val);
 			return val;
 		}
-		return 0;
+		break;
 	case ATOM_ARG_PLL:
 		idx = U8(*ptr);
 		(*ptr)++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/atombios_encoders.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/atombios_encoders.c
@@ -2089,23 +2089,29 @@
 					fake_edid_record = (ATOM_FAKE_EDID_PATCH_RECORD *)record;
 					if (fake_edid_record->ucFakeEDIDLength) {
 						struct edid *edid;
-						int edid_size =
-							max((int)EDID_LENGTH, (int)fake_edid_record->ucFakeEDIDLength);
-						edid = kmalloc(edid_size, GFP_KERNEL);
-						if (edid) {
-							memcpy((u8 *)edid, (u8 *)&fake_edid_record->ucFakeEDIDString[0],
-							       fake_edid_record->ucFakeEDIDLength);
+						int edid_size;
 
+						if (fake_edid_record->ucFakeEDIDLength == 128)
+							edid_size = fake_edid_record->ucFakeEDIDLength;
+						else
+							edid_size = fake_edid_record->ucFakeEDIDLength * 128;
+						edid = kmemdup(&fake_edid_record->ucFakeEDIDString[0],
+							       edid_size, GFP_KERNEL);
+						if (edid) {
 							if (drm_edid_is_valid(edid)) {
 								adev->mode_info.bios_hardcoded_edid = edid;
 								adev->mode_info.bios_hardcoded_edid_size = edid_size;
-							} else
+							} else {
 								kfree(edid);
+							}
 						}
+						record += struct_size(fake_edid_record,
+								      ucFakeEDIDString,
+								      edid_size);
+					} else {
+						/* empty fake edid record must be 3 bytes long */
+						record += sizeof(ATOM_FAKE_EDID_PATCH_RECORD) + 1;
 					}
-					record += fake_edid_record->ucFakeEDIDLength ?
-						fake_edid_record->ucFakeEDIDLength + 2 :
-						sizeof(ATOM_FAKE_EDID_PATCH_RECORD);
 					break;
 				case LCD_PANEL_RESOLUTION_RECORD_TYPE:
 					panel_res_record = (ATOM_PANEL_RESOLUTION_PATCH_RECORD *)record;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/cik.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/cik.c
@@ -1428,6 +1428,10 @@
 {
 	int r;
 
+	/* APUs don't have full asic reset */
+	if (adev->flags & AMD_IS_APU)
+		return 0;
+
 	if (cik_asic_reset_method(adev) == AMD_RESET_METHOD_BACO) {
 		dev_info(adev->dev, "BACO reset\n");
 		r = amdgpu_dpm_baco_reset(adev);
@@ -1570,17 +1574,8 @@
 			u16 bridge_cfg2, gpu_cfg2;
 			u32 max_lw, current_lw, tmp;
 
-			pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-						  &bridge_cfg);
-			pcie_capability_read_word(adev->pdev, PCI_EXP_LNKCTL,
-						  &gpu_cfg);
-
-			tmp16 = bridge_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(root, PCI_EXP_LNKCTL, tmp16);
-
-			tmp16 = gpu_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(adev->pdev, PCI_EXP_LNKCTL,
-						   tmp16);
+			pcie_capability_set_word(root, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
+			pcie_capability_set_word(adev->pdev, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
 
 			tmp = RREG32_PCIE(ixPCIE_LC_STATUS1);
 			max_lw = (tmp & PCIE_LC_STATUS1__LC_DETECTED_LINK_WIDTH_MASK) >>
@@ -1633,21 +1628,14 @@
 				msleep(100);
 
 				/* linkctl */
-				pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (bridge_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(root, PCI_EXP_LNKCTL,
-							   tmp16);
-
-				pcie_capability_read_word(adev->pdev,
-							  PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (gpu_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(adev->pdev,
-							   PCI_EXP_LNKCTL,
-							   tmp16);
+				pcie_capability_clear_and_set_word(root, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   bridge_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
+				pcie_capability_clear_and_set_word(adev->pdev, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   gpu_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
 
 				/* linkctl2 */
 				pcie_capability_read_word(root, PCI_EXP_LNKCTL2,
@@ -1715,7 +1703,7 @@
 	bool disable_l0s = false, disable_l1 = false, disable_plloff_in_l1 = false;
 	bool disable_clkreq = false;
 
-	if (amdgpu_aspm == 0)
+	if (!amdgpu_device_should_use_aspm(adev))
 		return;
 
 	if (pci_is_root_bus(adev->pdev->bus))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/cik_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/cik_ih.c
@@ -204,6 +204,12 @@
 		tmp = RREG32(mmIH_RB_CNTL);
 		tmp |= IH_RB_CNTL__WPTR_OVERFLOW_CLEAR_MASK;
 		WREG32(mmIH_RB_CNTL, tmp);
+
+		/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+		 * can be detected.
+		 */
+		tmp &= ~IH_RB_CNTL__WPTR_OVERFLOW_CLEAR_MASK;
+		WREG32(mmIH_RB_CNTL, tmp);
 	}
 	return (wptr & ih->ptr_mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/cz_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/cz_ih.c
@@ -216,6 +216,11 @@
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
 	WREG32(mmIH_RB_CNTL, tmp);
 
+	/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+	 * can be detected.
+	 */
+	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	WREG32(mmIH_RB_CNTL, tmp);
 
 out:
 	return (wptr & ih->ptr_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/df_v1_7.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/df_v1_7.c
@@ -70,6 +70,8 @@
 	int fb_channel_number;
 
 	fb_channel_number = adev->df.funcs->get_fb_channel_number(adev);
+	if (fb_channel_number >= ARRAY_SIZE(df_v1_7_channel_number))
+		fb_channel_number = 0;
 
 	return df_v1_7_channel_number[fb_channel_number];
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c
@@ -7197,8 +7197,10 @@
 		return r;
 
 	r = amdgpu_bo_kmap(ring->mqd_obj, (void **)&ring->mqd_ptr);
-	if (unlikely(r != 0))
+	if (unlikely(r != 0)) {
+		amdgpu_bo_unreserve(ring->mqd_obj);
 		return r;
+	}
 
 	gfx_v10_0_kiq_init_queue(ring);
 	amdgpu_bo_kunmap(ring->mqd_obj);
@@ -7729,8 +7731,19 @@
 	switch (adev->asic_type) {
 	case CHIP_VANGOGH:
 	case CHIP_YELLOW_CARP:
-		clock = (uint64_t)RREG32_SOC15(SMUIO, 0, mmGOLDEN_TSC_COUNT_LOWER_Vangogh) |
-			((uint64_t)RREG32_SOC15(SMUIO, 0, mmGOLDEN_TSC_COUNT_UPPER_Vangogh) << 32ULL);
+		preempt_disable();
+		clock_hi = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_UPPER_Vangogh);
+		clock_lo = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_LOWER_Vangogh);
+		hi_check = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_UPPER_Vangogh);
+		/* The SMUIO TSC clock frequency is 100MHz, which sets 32-bit carry over
+		 * roughly every 42 seconds.
+		 */
+		if (hi_check != clock_hi) {
+			clock_lo = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_LOWER_Vangogh);
+			clock_hi = hi_check;
+		}
+		preempt_enable();
+		clock = clock_lo | (clock_hi << 32ULL);
 		break;
 	default:
 		preempt_disable();
@@ -8411,8 +8424,14 @@
 		break;
 	case CHIP_VANGOGH:
 	case CHIP_YELLOW_CARP:
+		if (!enable)
+			amdgpu_gfx_off_ctrl(adev, false);
+
 		gfx_v10_cntl_pg(adev, enable);
-		amdgpu_gfx_off_ctrl(adev, enable);
+
+		if (enable)
+			amdgpu_gfx_off_ctrl(adev, true);
+
 		break;
 	default:
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c
@@ -140,6 +140,11 @@
 #define mmTCP_CHAN_STEER_5_ARCT								0x0b0c
 #define mmTCP_CHAN_STEER_5_ARCT_BASE_IDX							0
 
+#define mmGOLDEN_TSC_COUNT_UPPER_Renoir                0x0025
+#define mmGOLDEN_TSC_COUNT_UPPER_Renoir_BASE_IDX       1
+#define mmGOLDEN_TSC_COUNT_LOWER_Renoir                0x0026
+#define mmGOLDEN_TSC_COUNT_LOWER_Renoir_BASE_IDX       1
+
 enum ta_ras_gfx_subblock {
 	/*CPC*/
 	TA_RAS_BLOCK__GFX_CPC_INDEX_START = 0,
@@ -1267,6 +1272,12 @@
 	{ 0x1002, 0x15dd, 0x103c, 0x83e7, 0xd3 },
 	/* GFXOFF is unstable on C6 parts with a VBIOS 113-RAVEN-114 */
 	{ 0x1002, 0x15dd, 0x1002, 0x15dd, 0xc6 },
+	/* Apple MacBook Pro (15-inch, 2019) Radeon Pro Vega 20 4 GB */
+	{ 0x1002, 0x69af, 0x106b, 0x019a, 0xc0 },
+	/* https://bbs.openkylin.top/t/topic/171497 */
+	{ 0x1002, 0x15d8, 0x19e5, 0x3e14, 0xc2 },
+	/* HP 705G4 DM with R5 2400G */
+	{ 0x1002, 0x15dd, 0x103c, 0x8464, 0xd6 },
 	{ 0, 0, 0, 0, 0 },
 };
 
@@ -2617,7 +2628,8 @@
 
 	gfx_v9_0_tiling_mode_table_init(adev);
 
-	gfx_v9_0_setup_rb(adev);
+	if (adev->gfx.num_gfx_rings)
+		gfx_v9_0_setup_rb(adev);
 	gfx_v9_0_get_cu_info(adev, &adev->gfx.cu_info);
 	adev->gfx.config.db_debug2 = RREG32_SOC15(GC, 0, mmDB_DEBUG2);
 
@@ -3056,8 +3068,8 @@
 			      AMD_PG_SUPPORT_CP |
 			      AMD_PG_SUPPORT_GDS |
 			      AMD_PG_SUPPORT_RLC_SMU_HS)) {
-		WREG32(mmRLC_JUMP_TABLE_RESTORE,
-		       adev->gfx.rlc.cp_table_gpu_addr >> 8);
+		WREG32_SOC15(GC, 0, mmRLC_JUMP_TABLE_RESTORE,
+			     adev->gfx.rlc.cp_table_gpu_addr >> 8);
 		gfx_v9_0_init_gfx_power_gating(adev);
 	}
 }
@@ -3260,6 +3272,14 @@
 
 	gfx_v9_0_cp_gfx_enable(adev, true);
 
+	/* Now only limit the quirk on the APU gfx9 series and already
+	 * confirmed that the APU gfx10/gfx11 needn't such update.
+	 */
+	if (adev->flags & AMD_IS_APU &&
+			adev->in_s3 && !adev->suspend_complete) {
+		DRM_INFO(" Will skip the CSB packet resubmit\n");
+		return 0;
+	}
 	r = amdgpu_ring_alloc(ring, gfx_v9_0_get_csb_size(adev) + 4 + 3);
 	if (r) {
 		DRM_ERROR("amdgpu: cp failed to lock ring (%d).\n", r);
@@ -3863,8 +3883,10 @@
 		return r;
 
 	r = amdgpu_bo_kmap(ring->mqd_obj, (void **)&ring->mqd_ptr);
-	if (unlikely(r != 0))
+	if (unlikely(r != 0)) {
+		amdgpu_bo_unreserve(ring->mqd_obj);
 		return r;
+	}
 
 	gfx_v9_0_kiq_init_queue(ring);
 	amdgpu_bo_kunmap(ring->mqd_obj);
@@ -4010,7 +4032,8 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
-	amdgpu_irq_put(adev, &adev->gfx.cp_ecc_error_irq, 0);
+	if (amdgpu_ras_is_supported(adev, AMDGPU_RAS_BLOCK__GFX))
+		amdgpu_irq_put(adev, &adev->gfx.cp_ecc_error_irq, 0);
 	amdgpu_irq_put(adev, &adev->gfx.priv_reg_irq, 0);
 	amdgpu_irq_put(adev, &adev->gfx.priv_inst_irq, 0);
 
@@ -4228,19 +4251,38 @@
 
 static uint64_t gfx_v9_0_get_gpu_clock_counter(struct amdgpu_device *adev)
 {
-	uint64_t clock;
+	uint64_t clock, clock_lo, clock_hi, hi_check;
 
-	amdgpu_gfx_off_ctrl(adev, false);
-	mutex_lock(&adev->gfx.gpu_clock_mutex);
-	if (adev->asic_type == CHIP_VEGA10 && amdgpu_sriov_runtime(adev)) {
-		clock = gfx_v9_0_kiq_read_clock(adev);
-	} else {
-		WREG32_SOC15(GC, 0, mmRLC_CAPTURE_GPU_CLOCK_COUNT, 1);
-		clock = (uint64_t)RREG32_SOC15(GC, 0, mmRLC_GPU_CLOCK_COUNT_LSB) |
-			((uint64_t)RREG32_SOC15(GC, 0, mmRLC_GPU_CLOCK_COUNT_MSB) << 32ULL);
+	switch (adev->asic_type) {
+	case CHIP_RENOIR:
+		preempt_disable();
+		clock_hi = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_UPPER_Renoir);
+		clock_lo = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_LOWER_Renoir);
+		hi_check = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_UPPER_Renoir);
+		/* The SMUIO TSC clock frequency is 100MHz, which sets 32-bit carry over
+		 * roughly every 42 seconds.
+		 */
+		if (hi_check != clock_hi) {
+			clock_lo = RREG32_SOC15_NO_KIQ(SMUIO, 0, mmGOLDEN_TSC_COUNT_LOWER_Renoir);
+			clock_hi = hi_check;
+		}
+		preempt_enable();
+		clock = clock_lo | (clock_hi << 32ULL);
+		break;
+	default:
+		amdgpu_gfx_off_ctrl(adev, false);
+		mutex_lock(&adev->gfx.gpu_clock_mutex);
+		if (adev->asic_type == CHIP_VEGA10 && amdgpu_sriov_runtime(adev)) {
+			clock = gfx_v9_0_kiq_read_clock(adev);
+		} else {
+			WREG32_SOC15(GC, 0, mmRLC_CAPTURE_GPU_CLOCK_COUNT, 1);
+			clock = (uint64_t)RREG32_SOC15(GC, 0, mmRLC_GPU_CLOCK_COUNT_LSB) |
+				((uint64_t)RREG32_SOC15(GC, 0, mmRLC_GPU_CLOCK_COUNT_MSB) << 32ULL);
+		}
+		mutex_unlock(&adev->gfx.gpu_clock_mutex);
+		amdgpu_gfx_off_ctrl(adev, true);
+		break;
 	}
-	mutex_unlock(&adev->gfx.gpu_clock_mutex);
-	amdgpu_gfx_off_ctrl(adev, true);
 	return clock;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gfxhub_v1_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gfxhub_v1_0.c
@@ -162,7 +162,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC);/* XXX for emulation. */
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL, ATC_EN, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gfxhub_v2_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gfxhub_v2_0.c
@@ -196,7 +196,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, GCMC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, GCMC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, GCMC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC); /* UC, uncached */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gfxhub_v2_1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gfxhub_v2_1.c
@@ -197,7 +197,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, GCMC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, GCMC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, GCMC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC); /* UC, uncached */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gmc_v10_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gmc_v10_0.c
@@ -414,6 +414,7 @@
 	uint32_t seq;
 	uint16_t queried_pasid;
 	bool ret;
+	u32 usec_timeout = amdgpu_sriov_vf(adev) ? SRIOV_USEC_TIMEOUT : adev->usec_timeout;
 	struct amdgpu_ring *ring = &adev->gfx.kiq.ring;
 	struct amdgpu_kiq *kiq = &adev->gfx.kiq;
 
@@ -432,7 +433,7 @@
 
 		amdgpu_ring_commit(ring);
 		spin_unlock(&adev->gfx.kiq.ring_lock);
-		r = amdgpu_fence_wait_polling(ring, seq, adev->usec_timeout);
+		r = amdgpu_fence_wait_polling(ring, seq, usec_timeout);
 		if (r < 1) {
 			dev_err(adev->dev, "wait for kiq fence error: %ld.\n", r);
 			return -ETIME;
@@ -788,7 +789,7 @@
 	adev->gmc.aper_size = pci_resource_len(adev->pdev, 0);
 
 #ifdef CONFIG_X86_64
-	if (adev->flags & AMD_IS_APU) {
+	if ((adev->flags & AMD_IS_APU) && !amdgpu_passthrough(adev)) {
 		adev->gmc.aper_base = adev->gfxhub.funcs->get_mc_fb_offset(adev);
 		adev->gmc.aper_size = adev->gmc.real_vram_size;
 	}
@@ -1021,10 +1022,14 @@
 		return -EINVAL;
 	}
 
+	if (amdgpu_sriov_vf(adev) && amdgpu_in_reset(adev))
+		goto skip_pin_bo;
+
 	r = amdgpu_gart_table_vram_pin(adev);
 	if (r)
 		return r;
 
+skip_pin_bo:
 	r = adev->gfxhub.funcs->gart_enable(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gmc_v6_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gmc_v6_0.c
@@ -841,12 +841,12 @@
 
 	adev->gmc.mc_mask = 0xffffffffffULL;
 
-	r = dma_set_mask_and_coherent(adev->dev, DMA_BIT_MASK(44));
+	r = dma_set_mask_and_coherent(adev->dev, DMA_BIT_MASK(40));
 	if (r) {
 		dev_warn(adev->dev, "No suitable DMA available.\n");
 		return r;
 	}
-	adev->need_swiotlb = drm_need_swiotlb(44);
+	adev->need_swiotlb = drm_need_swiotlb(40);
 
 	r = gmc_v6_0_init_microcode(adev);
 	if (r) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gmc_v7_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gmc_v7_0.c
@@ -381,8 +381,9 @@
 	adev->gmc.aper_size = pci_resource_len(adev->pdev, 0);
 
 #ifdef CONFIG_X86_64
-	if (adev->flags & AMD_IS_APU &&
-	    adev->gmc.real_vram_size > adev->gmc.aper_size) {
+	if ((adev->flags & AMD_IS_APU) &&
+	    adev->gmc.real_vram_size > adev->gmc.aper_size &&
+	    !amdgpu_passthrough(adev)) {
 		adev->gmc.aper_base = ((u64)RREG32(mmMC_VM_FB_OFFSET)) << 22;
 		adev->gmc.aper_size = adev->gmc.real_vram_size;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gmc_v8_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gmc_v8_0.c
@@ -515,10 +515,10 @@
 static int gmc_v8_0_mc_init(struct amdgpu_device *adev)
 {
 	int r;
+	u32 tmp;
 
 	adev->gmc.vram_width = amdgpu_atombios_get_vram_width(adev);
 	if (!adev->gmc.vram_width) {
-		u32 tmp;
 		int chansize, numchan;
 
 		/* Get VRAM informations */
@@ -562,8 +562,15 @@
 		adev->gmc.vram_width = numchan * chansize;
 	}
 	/* size in MB on si */
-	adev->gmc.mc_vram_size = RREG32(mmCONFIG_MEMSIZE) * 1024ULL * 1024ULL;
-	adev->gmc.real_vram_size = RREG32(mmCONFIG_MEMSIZE) * 1024ULL * 1024ULL;
+	tmp = RREG32(mmCONFIG_MEMSIZE);
+	/* some boards may have garbage in the upper 16 bits */
+	if (tmp & 0xffff0000) {
+		DRM_INFO("Probable bad vram size: 0x%08x\n", tmp);
+		if (tmp & 0xffff)
+			tmp &= 0xffff;
+	}
+	adev->gmc.mc_vram_size = tmp * 1024ULL * 1024ULL;
+	adev->gmc.real_vram_size = adev->gmc.mc_vram_size;
 
 	if (!(adev->flags & AMD_IS_APU)) {
 		r = amdgpu_device_resize_fb_bar(adev);
@@ -574,7 +581,7 @@
 	adev->gmc.aper_size = pci_resource_len(adev->pdev, 0);
 
 #ifdef CONFIG_X86_64
-	if (adev->flags & AMD_IS_APU) {
+	if ((adev->flags & AMD_IS_APU) && !amdgpu_passthrough(adev)) {
 		adev->gmc.aper_base = ((u64)RREG32(mmMC_VM_FB_OFFSET)) << 22;
 		adev->gmc.aper_size = adev->gmc.real_vram_size;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c
@@ -72,6 +72,9 @@
 #define mmDCHUBBUB_SDPIF_MMIO_CNTRL_0                                                                  0x049d
 #define mmDCHUBBUB_SDPIF_MMIO_CNTRL_0_BASE_IDX                                                         2
 
+#define mmHUBP0_DCSURF_PRI_VIEWPORT_DIMENSION_DCN2                                                          0x05ea
+#define mmHUBP0_DCSURF_PRI_VIEWPORT_DIMENSION_DCN2_BASE_IDX                                                 2
+
 
 static const char *gfxhub_client_ids[] = {
 	"CB",
@@ -860,6 +863,7 @@
 	uint32_t seq;
 	uint16_t queried_pasid;
 	bool ret;
+	u32 usec_timeout = amdgpu_sriov_vf(adev) ? SRIOV_USEC_TIMEOUT : adev->usec_timeout;
 	struct amdgpu_ring *ring = &adev->gfx.kiq.ring;
 	struct amdgpu_kiq *kiq = &adev->gfx.kiq;
 
@@ -899,7 +903,7 @@
 
 		amdgpu_ring_commit(ring);
 		spin_unlock(&adev->gfx.kiq.ring_lock);
-		r = amdgpu_fence_wait_polling(ring, seq, adev->usec_timeout);
+		r = amdgpu_fence_wait_polling(ring, seq, usec_timeout);
 		if (r < 1) {
 			dev_err(adev->dev, "wait for kiq fence error: %ld.\n", r);
 			up_read(&adev->reset_sem);
@@ -1103,6 +1107,8 @@
 	u32 d1vga_control = RREG32_SOC15(DCE, 0, mmD1VGA_CONTROL);
 	unsigned size;
 
+	/* TODO move to DC so GMC doesn't need to hard-code DCN registers */
+
 	if (REG_GET_FIELD(d1vga_control, D1VGA_CONTROL, D1VGA_MODE_ENABLE)) {
 		size = AMDGPU_VBIOS_VGA_ALLOCATION;
 	} else {
@@ -1110,7 +1116,6 @@
 
 		switch (adev->asic_type) {
 		case CHIP_RAVEN:
-		case CHIP_RENOIR:
 			viewport = RREG32_SOC15(DCE, 0, mmHUBP0_DCSURF_PRI_VIEWPORT_DIMENSION);
 			size = (REG_GET_FIELD(viewport,
 					      HUBP0_DCSURF_PRI_VIEWPORT_DIMENSION, PRI_VIEWPORT_HEIGHT) *
@@ -1118,6 +1123,14 @@
 					      HUBP0_DCSURF_PRI_VIEWPORT_DIMENSION, PRI_VIEWPORT_WIDTH) *
 				4);
 			break;
+		case CHIP_RENOIR:
+			viewport = RREG32_SOC15(DCE, 0, mmHUBP0_DCSURF_PRI_VIEWPORT_DIMENSION_DCN2);
+			size = (REG_GET_FIELD(viewport,
+					      HUBP0_DCSURF_PRI_VIEWPORT_DIMENSION, PRI_VIEWPORT_HEIGHT) *
+				REG_GET_FIELD(viewport,
+					      HUBP0_DCSURF_PRI_VIEWPORT_DIMENSION, PRI_VIEWPORT_WIDTH) *
+				4);
+			break;
 		case CHIP_VEGA10:
 		case CHIP_VEGA12:
 		case CHIP_VEGA20:
@@ -1375,7 +1388,7 @@
 	 */
 
 	/* check whether both host-gpu and gpu-gpu xgmi links exist */
-	if ((adev->flags & AMD_IS_APU) ||
+	if (((adev->flags & AMD_IS_APU) && !amdgpu_passthrough(adev)) ||
 	    (adev->gmc.xgmi.supported &&
 	     adev->gmc.xgmi.connected_to_cpu)) {
 		adev->gmc.aper_base =
@@ -1640,7 +1653,7 @@
 	amdgpu_gem_force_release(adev);
 	amdgpu_vm_manager_fini(adev);
 	amdgpu_gart_table_vram_free(adev);
-	amdgpu_bo_unref(&adev->gmc.pdb0_bo);
+	amdgpu_bo_free_kernel(&adev->gmc.pdb0_bo, NULL, &adev->gmc.ptr_pdb0);
 	amdgpu_bo_fini(adev);
 
 	return 0;
@@ -1708,10 +1721,14 @@
 		return -EINVAL;
 	}
 
+	if (amdgpu_sriov_vf(adev) && amdgpu_in_reset(adev))
+		goto skip_pin_bo;
+
 	r = amdgpu_gart_table_vram_pin(adev);
 	if (r)
 		return r;
 
+skip_pin_bo:
 	r = adev->gfxhub.funcs->gart_enable(adev);
 	if (r)
 		return r;
@@ -1802,7 +1819,6 @@
 		return 0;
 	}
 
-	amdgpu_irq_put(adev, &adev->gmc.ecc_irq, 0);
 	amdgpu_irq_put(adev, &adev->gmc.vm_fault, 0);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/iceland_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/iceland_ih.c
@@ -215,6 +215,11 @@
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
 	WREG32(mmIH_RB_CNTL, tmp);
 
+	/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+	 * can be detected.
+	 */
+	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	WREG32(mmIH_RB_CNTL, tmp);
 
 out:
 	return (wptr & ih->ptr_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/jpeg_v2_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/jpeg_v2_0.c
@@ -557,11 +557,11 @@
 
 	amdgpu_ring_write(ring, PACKETJ(mmUVD_LMI_JRBC_IB_VMID_INTERNAL_OFFSET,
 		0, 0, PACKETJ_TYPE0));
-	amdgpu_ring_write(ring, (vmid | (vmid << 4)));
+	amdgpu_ring_write(ring, (vmid | (vmid << 4) | (vmid << 8)));
 
 	amdgpu_ring_write(ring, PACKETJ(mmUVD_LMI_JPEG_VMID_INTERNAL_OFFSET,
 		0, 0, PACKETJ_TYPE0));
-	amdgpu_ring_write(ring, (vmid | (vmid << 4)));
+	amdgpu_ring_write(ring, (vmid | (vmid << 4) | (vmid << 8)));
 
 	amdgpu_ring_write(ring,	PACKETJ(mmUVD_LMI_JRBC_IB_64BIT_BAR_LOW_INTERNAL_OFFSET,
 		0, 0, PACKETJ_TYPE0));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c
@@ -145,7 +145,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC);/* XXX for emulation. */
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL, ATC_EN, 1);
@@ -177,6 +176,7 @@
 	tmp = REG_SET_FIELD(tmp, VM_L2_CNTL2, INVALIDATE_L2_CACHE, 1);
 	WREG32_SOC15(MMHUB, 0, mmVM_L2_CNTL2, tmp);
 
+	tmp = mmVM_L2_CNTL3_DEFAULT;
 	if (adev->gmc.translate_further) {
 		tmp = REG_SET_FIELD(tmp, VM_L2_CNTL3, BANK_SELECT, 12);
 		tmp = REG_SET_FIELD(tmp, VM_L2_CNTL3,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/mmhub_v1_7.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/mmhub_v1_7.c
@@ -165,7 +165,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC);/* XXX for emulation. */
 	tmp = REG_SET_FIELD(tmp, MC_VM_MX_L1_TLB_CNTL, ATC_EN, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/mmhub_v2_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/mmhub_v2_0.c
@@ -269,7 +269,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, MMMC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, MMMC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, MMMC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC); /* UC, uncached */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/mmhub_v2_3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/mmhub_v2_3.c
@@ -194,7 +194,6 @@
 			    ENABLE_ADVANCED_DRIVER_MODEL, 1);
 	tmp = REG_SET_FIELD(tmp, MMMC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
-	tmp = REG_SET_FIELD(tmp, MMMC_VM_MX_L1_TLB_CNTL, ECO_BITS, 0);
 	tmp = REG_SET_FIELD(tmp, MMMC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC); /* UC, uncached */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/mmhub_v9_4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/mmhub_v9_4.c
@@ -190,8 +190,6 @@
 	tmp = REG_SET_FIELD(tmp, VMSHAREDVC0_MC_VM_MX_L1_TLB_CNTL,
 			    SYSTEM_APERTURE_UNMAPPED_ACCESS, 0);
 	tmp = REG_SET_FIELD(tmp, VMSHAREDVC0_MC_VM_MX_L1_TLB_CNTL,
-			    ECO_BITS, 0);
-	tmp = REG_SET_FIELD(tmp, VMSHAREDVC0_MC_VM_MX_L1_TLB_CNTL,
 			    MTYPE, MTYPE_UC);/* XXX for emulation. */
 	tmp = REG_SET_FIELD(tmp, VMSHAREDVC0_MC_VM_MX_L1_TLB_CNTL,
 			    ATC_EN, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/navi10_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/navi10_ih.c
@@ -447,6 +447,12 @@
 	tmp = RREG32_NO_KIQ(ih_regs->ih_rb_cntl);
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
 	WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
+
+	/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+	 * can be detected.
+	 */
+	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
 out:
 	return (wptr & ih->ptr_mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/nbio_v2_3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/nbio_v2_3.c
@@ -366,6 +366,7 @@
 		WREG32_PCIE(smnPCIE_LC_CNTL, data);
 }
 
+#ifdef CONFIG_PCIEASPM
 static void nbio_v2_3_program_ltr(struct amdgpu_device *adev)
 {
 	uint32_t def, data;
@@ -387,9 +388,11 @@
 	if (def != data)
 		WREG32_PCIE(smnBIF_CFG_DEV0_EPF0_DEVICE_CNTL2, data);
 }
+#endif
 
 static void nbio_v2_3_program_aspm(struct amdgpu_device *adev)
 {
+#ifdef CONFIG_PCIEASPM
 	uint32_t def, data;
 
 	def = data = RREG32_PCIE(smnPCIE_LC_CNTL);
@@ -445,7 +448,10 @@
 	if (def != data)
 		WREG32_PCIE(smnPCIE_LC_CNTL6, data);
 
-	nbio_v2_3_program_ltr(adev);
+	/* Don't bother about LTR if LTR is not enabled
+	 * in the path */
+	if (adev->pdev->ltr_path)
+		nbio_v2_3_program_ltr(adev);
 
 	def = data = RREG32_SOC15(NBIO, 0, mmRCC_BIF_STRAP3);
 	data |= 0x5DE0 << RCC_BIF_STRAP3__STRAP_VLINK_ASPM_IDLE_TIMER__SHIFT;
@@ -469,6 +475,7 @@
 	data &= ~PCIE_LC_CNTL3__LC_DSC_DONT_ENTER_L23_AFTER_PME_ACK_MASK;
 	if (def != data)
 		WREG32_PCIE(smnPCIE_LC_CNTL3, data);
+#endif
 }
 
 static void nbio_v2_3_apply_lc_spc_mode_wa(struct amdgpu_device *adev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/nbio_v6_1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/nbio_v6_1.c
@@ -278,6 +278,7 @@
 		WREG32_PCIE(smnPCIE_CI_CNTL, data);
 }
 
+#ifdef CONFIG_PCIEASPM
 static void nbio_v6_1_program_ltr(struct amdgpu_device *adev)
 {
 	uint32_t def, data;
@@ -299,9 +300,11 @@
 	if (def != data)
 		WREG32_PCIE(smnBIF_CFG_DEV0_EPF0_DEVICE_CNTL2, data);
 }
+#endif
 
 static void nbio_v6_1_program_aspm(struct amdgpu_device *adev)
 {
+#ifdef CONFIG_PCIEASPM
 	uint32_t def, data;
 
 	def = data = RREG32_PCIE(smnPCIE_LC_CNTL);
@@ -357,7 +360,10 @@
 	if (def != data)
 		WREG32_PCIE(smnPCIE_LC_CNTL6, data);
 
-	nbio_v6_1_program_ltr(adev);
+	/* Don't bother about LTR if LTR is not enabled
+	 * in the path */
+	if (adev->pdev->ltr_path)
+		nbio_v6_1_program_ltr(adev);
 
 	def = data = RREG32_PCIE(smnRCC_BIF_STRAP3);
 	data |= 0x5DE0 << RCC_BIF_STRAP3__STRAP_VLINK_ASPM_IDLE_TIMER__SHIFT;
@@ -381,6 +387,7 @@
 	data &= ~PCIE_LC_CNTL3__LC_DSC_DONT_ENTER_L23_AFTER_PME_ACK_MASK;
 	if (def != data)
 		WREG32_PCIE(smnPCIE_LC_CNTL3, data);
+#endif
 }
 
 const struct amdgpu_nbio_funcs nbio_v6_1_funcs = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/nbio_v7_4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/nbio_v7_4.c
@@ -370,7 +370,7 @@
 		else
 			WREG32_SOC15(NBIO, 0, mmBIF_DOORBELL_INT_CNTL, bif_doorbell_intr_cntl);
 
-		if (!ras->disable_ras_err_cnt_harvest) {
+		if (ras && !ras->disable_ras_err_cnt_harvest && obj) {
 			/*
 			 * clear error status after ras_controller_intr
 			 * according to hw team and count ue number
@@ -630,6 +630,7 @@
 	.ras_fini = amdgpu_nbio_ras_fini,
 };
 
+#ifdef CONFIG_PCIEASPM
 static void nbio_v7_4_program_ltr(struct amdgpu_device *adev)
 {
 	uint32_t def, data;
@@ -651,9 +652,11 @@
 	if (def != data)
 		WREG32_PCIE(smnBIF_CFG_DEV0_EPF0_DEVICE_CNTL2, data);
 }
+#endif
 
 static void nbio_v7_4_program_aspm(struct amdgpu_device *adev)
 {
+#ifdef CONFIG_PCIEASPM
 	uint32_t def, data;
 
 	def = data = RREG32_PCIE(smnPCIE_LC_CNTL);
@@ -709,7 +712,10 @@
 	if (def != data)
 		WREG32_PCIE(smnPCIE_LC_CNTL6, data);
 
-	nbio_v7_4_program_ltr(adev);
+	/* Don't bother about LTR if LTR is not enabled
+	 * in the path */
+	if (adev->pdev->ltr_path)
+		nbio_v7_4_program_ltr(adev);
 
 	def = data = RREG32_PCIE(smnRCC_BIF_STRAP3);
 	data |= 0x5DE0 << RCC_BIF_STRAP3__STRAP_VLINK_ASPM_IDLE_TIMER__SHIFT;
@@ -733,6 +739,7 @@
 	data &= ~PCIE_LC_CNTL3__LC_DSC_DONT_ENTER_L23_AFTER_PME_ACK_MASK;
 	if (def != data)
 		WREG32_PCIE(smnPCIE_LC_CNTL3, data);
+#endif
 }
 
 const struct amdgpu_nbio_funcs nbio_v7_4_funcs = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/nv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/nv.c
@@ -87,7 +87,7 @@
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_MPEG4_AVC, 4096, 4906, 52)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_VC1, 4096, 4906, 4)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_HEVC, 8192, 4352, 186)},
-	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_JPEG, 4096, 4096, 0)},
+	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_JPEG, 8192, 8192, 0)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_VP9, 8192, 4352, 0)},
 };
 
@@ -170,6 +170,7 @@
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_HEVC, 8192, 4352, 186)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_VP9, 8192, 4352, 0)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_JPEG, 4096, 4096, 0)},
+	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_AV1, 8192, 4352, 0)},
 };
 
 static const struct amdgpu_video_codecs yc_video_codecs_decode = {
@@ -583,7 +584,7 @@
 
 static void nv_program_aspm(struct amdgpu_device *adev)
 {
-	if (!amdgpu_aspm)
+	if (!amdgpu_device_should_use_aspm(adev) || !amdgpu_device_aspm_support_quirk())
 		return;
 
 	if (!(adev->flags & AMD_IS_APU) &&
@@ -1001,7 +1002,8 @@
 		adev->gfx.funcs->update_perfmon_mgcg(adev, !enter);
 
 	if (!(adev->flags & AMD_IS_APU) &&
-	    (adev->nbio.funcs->enable_aspm))
+	    (adev->nbio.funcs->enable_aspm) &&
+	     amdgpu_device_should_use_aspm(adev))
 		adev->nbio.funcs->enable_aspm(adev, !enter);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/psp_v13_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/psp_v13_0.c
@@ -101,14 +101,15 @@
 	int ret;
 	int retry_loop;
 
+	/* Wait for bootloader to signify that it is ready having bit 31 of
+	 * C2PMSG_35 set to 1. All other bits are expected to be cleared.
+	 * If there is an error in processing command, bits[7:0] will be set.
+	 * This is applicable for PSP v13.0.6 and newer.
+	 */
 	for (retry_loop = 0; retry_loop < 10; retry_loop++) {
-		/* Wait for bootloader to signify that is
-		    ready having bit 31 of C2PMSG_35 set to 1 */
-		ret = psp_wait_for(psp,
-				   SOC15_REG_OFFSET(MP0, 0, regMP0_SMN_C2PMSG_35),
-				   0x80000000,
-				   0x80000000,
-				   false);
+		ret = psp_wait_for(
+			psp, SOC15_REG_OFFSET(MP0, 0, regMP0_SMN_C2PMSG_35),
+			0x80000000, 0xffffffff, false);
 
 		if (ret == 0)
 			return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c
@@ -770,8 +770,8 @@
 
 		DRM_DEBUG("Using doorbell -- "
 				"wptr_offs == 0x%08x "
-				"lower_32_bits(ring->wptr) << 2 == 0x%08x "
-				"upper_32_bits(ring->wptr) << 2 == 0x%08x\n",
+				"lower_32_bits(ring->wptr << 2) == 0x%08x "
+				"upper_32_bits(ring->wptr << 2) == 0x%08x\n",
 				ring->wptr_offs,
 				lower_32_bits(ring->wptr << 2),
 				upper_32_bits(ring->wptr << 2));
@@ -978,13 +978,13 @@
 
 
 /**
- * sdma_v4_0_gfx_stop - stop the gfx async dma engines
+ * sdma_v4_0_gfx_enable - enable the gfx async dma engines
  *
  * @adev: amdgpu_device pointer
- *
- * Stop the gfx async dma ring buffers (VEGA10).
+ * @enable: enable SDMA RB/IB
+ * control the gfx async dma ring buffers (VEGA10).
  */
-static void sdma_v4_0_gfx_stop(struct amdgpu_device *adev)
+static void sdma_v4_0_gfx_enable(struct amdgpu_device *adev, bool enable)
 {
 	struct amdgpu_ring *sdma[AMDGPU_MAX_SDMA_INSTANCES];
 	u32 rb_cntl, ib_cntl;
@@ -999,10 +999,10 @@
 		}
 
 		rb_cntl = RREG32_SDMA(i, mmSDMA0_GFX_RB_CNTL);
-		rb_cntl = REG_SET_FIELD(rb_cntl, SDMA0_GFX_RB_CNTL, RB_ENABLE, 0);
+		rb_cntl = REG_SET_FIELD(rb_cntl, SDMA0_GFX_RB_CNTL, RB_ENABLE, enable ? 1 : 0);
 		WREG32_SDMA(i, mmSDMA0_GFX_RB_CNTL, rb_cntl);
 		ib_cntl = RREG32_SDMA(i, mmSDMA0_GFX_IB_CNTL);
-		ib_cntl = REG_SET_FIELD(ib_cntl, SDMA0_GFX_IB_CNTL, IB_ENABLE, 0);
+		ib_cntl = REG_SET_FIELD(ib_cntl, SDMA0_GFX_IB_CNTL, IB_ENABLE, enable ? 1 : 0);
 		WREG32_SDMA(i, mmSDMA0_GFX_IB_CNTL, ib_cntl);
 	}
 }
@@ -1129,7 +1129,7 @@
 	int i;
 
 	if (!enable) {
-		sdma_v4_0_gfx_stop(adev);
+		sdma_v4_0_gfx_enable(adev, enable);
 		sdma_v4_0_rlc_stop(adev);
 		if (adev->sdma.has_page_queue)
 			sdma_v4_0_page_stop(adev);
@@ -2044,9 +2044,11 @@
 	if (amdgpu_sriov_vf(adev))
 		return 0;
 
-	for (i = 0; i < adev->sdma.num_instances; i++) {
-		amdgpu_irq_put(adev, &adev->sdma.ecc_irq,
-			       AMDGPU_SDMA_IRQ_INSTANCE0 + i);
+	if (amdgpu_ras_is_supported(adev, AMDGPU_RAS_BLOCK__SDMA)) {
+		for (i = 0; i < adev->sdma.num_instances; i++) {
+			amdgpu_irq_put(adev, &adev->sdma.ecc_irq,
+				       AMDGPU_SDMA_IRQ_INSTANCE0 + i);
+		}
 	}
 
 	sdma_v4_0_ctx_switch_enable(adev, false);
@@ -2062,6 +2064,12 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	/* SMU saves SDMA state for us */
+	if (adev->in_s0ix) {
+		sdma_v4_0_gfx_enable(adev, false);
+		return 0;
+	}
+
 	return sdma_v4_0_hw_fini(adev);
 }
 
@@ -2069,6 +2077,14 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	/* SMU restores SDMA state for us */
+	if (adev->in_s0ix) {
+		sdma_v4_0_enable(adev, true);
+		sdma_v4_0_gfx_enable(adev, true);
+		amdgpu_ttm_set_buffer_funcs_status(adev, true);
+		return 0;
+	}
+
 	return sdma_v4_0_hw_init(adev);
 }
 
@@ -2132,10 +2148,13 @@
 				      struct amdgpu_irq_src *source,
 				      struct amdgpu_iv_entry *entry)
 {
-	uint32_t instance;
+	int instance;
 
 	DRM_DEBUG("IH: SDMA trap\n");
 	instance = sdma_v4_0_irq_id_to_seq(entry->client_id);
+	if (instance < 0)
+		return instance;
+
 	switch (entry->ring_id) {
 	case 0:
 		amdgpu_fence_process(&adev->sdma.instance[instance].ring);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/sdma_v5_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/sdma_v5_0.c
@@ -400,8 +400,8 @@
 	if (ring->use_doorbell) {
 		DRM_DEBUG("Using doorbell -- "
 				"wptr_offs == 0x%08x "
-				"lower_32_bits(ring->wptr) << 2 == 0x%08x "
-				"upper_32_bits(ring->wptr) << 2 == 0x%08x\n",
+				"lower_32_bits(ring->wptr << 2) == 0x%08x "
+				"upper_32_bits(ring->wptr << 2) == 0x%08x\n",
 				ring->wptr_offs,
 				lower_32_bits(ring->wptr << 2),
 				upper_32_bits(ring->wptr << 2));
@@ -782,9 +782,9 @@
 
 		if (!amdgpu_sriov_vf(adev)) { /* only bare-metal use register write for wptr */
 			WREG32(sdma_v5_0_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR),
-			       lower_32_bits(ring->wptr) << 2);
+			       lower_32_bits(ring->wptr << 2));
 			WREG32(sdma_v5_0_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR_HI),
-			       upper_32_bits(ring->wptr) << 2);
+			       upper_32_bits(ring->wptr << 2));
 		}
 
 		doorbell = RREG32_SOC15_IP(GC, sdma_v5_0_get_reg_offset(adev, i, mmSDMA0_GFX_DOORBELL));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/sdma_v5_2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/sdma_v5_2.c
@@ -287,8 +287,8 @@
 	if (ring->use_doorbell) {
 		DRM_DEBUG("Using doorbell -- "
 				"wptr_offs == 0x%08x "
-				"lower_32_bits(ring->wptr) << 2 == 0x%08x "
-				"upper_32_bits(ring->wptr) << 2 == 0x%08x\n",
+				"lower_32_bits(ring->wptr << 2) == 0x%08x "
+				"upper_32_bits(ring->wptr << 2) == 0x%08x\n",
 				ring->wptr_offs,
 				lower_32_bits(ring->wptr << 2),
 				upper_32_bits(ring->wptr << 2));
@@ -298,6 +298,14 @@
 		DRM_DEBUG("calling WDOORBELL64(0x%08x, 0x%016llx)\n",
 				ring->doorbell_index, ring->wptr << 2);
 		WDOORBELL64(ring->doorbell_index, ring->wptr << 2);
+		/* SDMA seems to miss doorbells sometimes when powergating kicks in.
+		 * Updating the wptr directly will wake it. This is only safe because
+		 * we disallow gfxoff in begin_use() and then allow it again in end_use().
+		 */
+		WREG32(sdma_v5_2_get_reg_offset(adev, ring->me, mmSDMA0_GFX_RB_WPTR),
+		       lower_32_bits(ring->wptr << 2));
+		WREG32(sdma_v5_2_get_reg_offset(adev, ring->me, mmSDMA0_GFX_RB_WPTR_HI),
+		       upper_32_bits(ring->wptr << 2));
 	} else {
 		DRM_DEBUG("Not using doorbell -- "
 				"mmSDMA%i_GFX_RB_WPTR == 0x%08x "
@@ -404,17 +412,21 @@
 	u32 ref_and_mask = 0;
 	const struct nbio_hdp_flush_reg *nbio_hf_reg = adev->nbio.hdp_flush_reg;
 
-	ref_and_mask = nbio_hf_reg->ref_and_mask_sdma0 << ring->me;
+	if (ring->me > 1) {
+		amdgpu_asic_flush_hdp(adev, ring);
+	} else {
+		ref_and_mask = nbio_hf_reg->ref_and_mask_sdma0 << ring->me;
 
-	amdgpu_ring_write(ring, SDMA_PKT_HEADER_OP(SDMA_OP_POLL_REGMEM) |
-			  SDMA_PKT_POLL_REGMEM_HEADER_HDP_FLUSH(1) |
-			  SDMA_PKT_POLL_REGMEM_HEADER_FUNC(3)); /* == */
-	amdgpu_ring_write(ring, (adev->nbio.funcs->get_hdp_flush_done_offset(adev)) << 2);
-	amdgpu_ring_write(ring, (adev->nbio.funcs->get_hdp_flush_req_offset(adev)) << 2);
-	amdgpu_ring_write(ring, ref_and_mask); /* reference */
-	amdgpu_ring_write(ring, ref_and_mask); /* mask */
-	amdgpu_ring_write(ring, SDMA_PKT_POLL_REGMEM_DW5_RETRY_COUNT(0xfff) |
-			  SDMA_PKT_POLL_REGMEM_DW5_INTERVAL(10)); /* retry count, poll interval */
+		amdgpu_ring_write(ring, SDMA_PKT_HEADER_OP(SDMA_OP_POLL_REGMEM) |
+				  SDMA_PKT_POLL_REGMEM_HEADER_HDP_FLUSH(1) |
+				  SDMA_PKT_POLL_REGMEM_HEADER_FUNC(3)); /* == */
+		amdgpu_ring_write(ring, (adev->nbio.funcs->get_hdp_flush_done_offset(adev)) << 2);
+		amdgpu_ring_write(ring, (adev->nbio.funcs->get_hdp_flush_req_offset(adev)) << 2);
+		amdgpu_ring_write(ring, ref_and_mask); /* reference */
+		amdgpu_ring_write(ring, ref_and_mask); /* mask */
+		amdgpu_ring_write(ring, SDMA_PKT_POLL_REGMEM_DW5_RETRY_COUNT(0xfff) |
+				  SDMA_PKT_POLL_REGMEM_DW5_INTERVAL(10)); /* retry count, poll interval */
+	}
 }
 
 /**
@@ -660,8 +672,8 @@
 		WREG32_SOC15_IP(GC, sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_MINOR_PTR_UPDATE), 1);
 
 		if (!amdgpu_sriov_vf(adev)) { /* only bare-metal use register write for wptr */
-			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR), lower_32_bits(ring->wptr) << 2);
-			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR_HI), upper_32_bits(ring->wptr) << 2);
+			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR), lower_32_bits(ring->wptr << 2));
+			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR_HI), upper_32_bits(ring->wptr << 2));
 		}
 
 		doorbell = RREG32_SOC15_IP(GC, sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_DOORBELL));
@@ -1660,6 +1672,36 @@
 		*flags |= AMD_CG_SUPPORT_SDMA_LS;
 }
 
+static void sdma_v5_2_ring_begin_use(struct amdgpu_ring *ring)
+{
+	struct amdgpu_device *adev = ring->adev;
+
+	/* SDMA 5.2.3 (RMB) FW doesn't seem to properly
+	 * disallow GFXOFF in some cases leading to
+	 * hangs in SDMA.  Disallow GFXOFF while SDMA is active.
+	 * We can probably just limit this to 5.2.3,
+	 * but it shouldn't hurt for other parts since
+	 * this GFXOFF will be disallowed anyway when SDMA is
+	 * active, this just makes it explicit.
+	 * sdma_v5_2_ring_set_wptr() takes advantage of this
+	 * to update the wptr because sometimes SDMA seems to miss
+	 * doorbells when entering PG.  If you remove this, update
+	 * sdma_v5_2_ring_set_wptr() as well!
+	 */
+	amdgpu_gfx_off_ctrl(adev, false);
+}
+
+static void sdma_v5_2_ring_end_use(struct amdgpu_ring *ring)
+{
+	struct amdgpu_device *adev = ring->adev;
+
+	/* SDMA 5.2.3 (RMB) FW doesn't seem to properly
+	 * disallow GFXOFF in some cases leading to
+	 * hangs in SDMA.  Allow GFXOFF when SDMA is complete.
+	 */
+	amdgpu_gfx_off_ctrl(adev, true);
+}
+
 const struct amd_ip_funcs sdma_v5_2_ip_funcs = {
 	.name = "sdma_v5_2",
 	.early_init = sdma_v5_2_early_init,
@@ -1707,6 +1749,8 @@
 	.test_ib = sdma_v5_2_ring_test_ib,
 	.insert_nop = sdma_v5_2_ring_insert_nop,
 	.pad_ib = sdma_v5_2_ring_pad_ib,
+	.begin_use = sdma_v5_2_ring_begin_use,
+	.end_use = sdma_v5_2_ring_end_use,
 	.emit_wreg = sdma_v5_2_ring_emit_wreg,
 	.emit_reg_wait = sdma_v5_2_ring_emit_reg_wait,
 	.emit_reg_write_reg_wait = sdma_v5_2_ring_emit_reg_write_reg_wait,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/si.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/si.c
@@ -2276,17 +2276,8 @@
 			u16 bridge_cfg2, gpu_cfg2;
 			u32 max_lw, current_lw, tmp;
 
-			pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-						  &bridge_cfg);
-			pcie_capability_read_word(adev->pdev, PCI_EXP_LNKCTL,
-						  &gpu_cfg);
-
-			tmp16 = bridge_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(root, PCI_EXP_LNKCTL, tmp16);
-
-			tmp16 = gpu_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(adev->pdev, PCI_EXP_LNKCTL,
-						   tmp16);
+			pcie_capability_set_word(root, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
+			pcie_capability_set_word(adev->pdev, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
 
 			tmp = RREG32_PCIE(PCIE_LC_STATUS1);
 			max_lw = (tmp & LC_DETECTED_LINK_WIDTH_MASK) >> LC_DETECTED_LINK_WIDTH_SHIFT;
@@ -2331,21 +2322,14 @@
 
 				mdelay(100);
 
-				pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (bridge_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(root, PCI_EXP_LNKCTL,
-							   tmp16);
-
-				pcie_capability_read_word(adev->pdev,
-							  PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (gpu_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(adev->pdev,
-							   PCI_EXP_LNKCTL,
-							   tmp16);
+				pcie_capability_clear_and_set_word(root, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   bridge_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
+				pcie_capability_clear_and_set_word(adev->pdev, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   gpu_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
 
 				pcie_capability_read_word(root, PCI_EXP_LNKCTL2,
 							  &tmp16);
@@ -2453,7 +2437,7 @@
 	bool disable_l0s = false, disable_l1 = false, disable_plloff_in_l1 = false;
 	bool disable_clkreq = false;
 
-	if (amdgpu_aspm == 0)
+	if (!amdgpu_device_should_use_aspm(adev))
 		return;
 
 	if (adev->flags & AMD_IS_APU)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/si_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/si_ih.c
@@ -119,6 +119,12 @@
 		tmp = RREG32(IH_RB_CNTL);
 		tmp |= IH_RB_CNTL__WPTR_OVERFLOW_CLEAR_MASK;
 		WREG32(IH_RB_CNTL, tmp);
+
+		/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+		 * can be detected.
+		 */
+		tmp &= ~IH_RB_CNTL__WPTR_OVERFLOW_CLEAR_MASK;
+		WREG32(IH_RB_CNTL, tmp);
 	}
 	return (wptr & ih->ptr_mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/soc15.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/soc15.c
@@ -123,7 +123,7 @@
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_MPEG4_AVC, 4096, 4906, 52)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_VC1, 4096, 4906, 4)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_HEVC, 4096, 4096, 186)},
-	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_JPEG, 4096, 4096, 0)},
+	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_JPEG, 8192, 8192, 0)},
 	{codec_info_build(AMDGPU_INFO_VIDEO_CAPS_CODEC_IDX_VP9, 4096, 4096, 0)},
 };
 
@@ -461,8 +461,9 @@
 	*value = 0;
 	for (i = 0; i < ARRAY_SIZE(soc15_allowed_read_registers); i++) {
 		en = &soc15_allowed_read_registers[i];
-		if (adev->reg_offset[en->hwip][en->inst] &&
-			reg_offset != (adev->reg_offset[en->hwip][en->inst][en->seg]
+		if (!adev->reg_offset[en->hwip][en->inst])
+			continue;
+		else if (reg_offset != (adev->reg_offset[en->hwip][en->inst][en->seg]
 					+ en->reg_offset))
 			continue;
 
@@ -604,11 +605,34 @@
 		return AMD_RESET_METHOD_MODE1;
 }
 
+static bool soc15_need_reset_on_resume(struct amdgpu_device *adev)
+{
+	u32 sol_reg;
+
+	sol_reg = RREG32_SOC15(MP0, 0, mmMP0_SMN_C2PMSG_81);
+
+	/* Will reset for the following suspend abort cases.
+	 * 1) Only reset limit on APU side, dGPU hasn't checked yet.
+	 * 2) S3 suspend abort and TOS already launched.
+	 */
+	if (adev->flags & AMD_IS_APU && adev->in_s3 &&
+			!adev->suspend_complete &&
+			sol_reg)
+		return true;
+
+	return false;
+}
+
 static int soc15_asic_reset(struct amdgpu_device *adev)
 {
 	/* original raven doesn't have full asic reset */
-	if ((adev->apu_flags & AMD_APU_IS_RAVEN) &&
-	    !(adev->apu_flags & AMD_APU_IS_RAVEN2))
+	/* On the latest Raven, the GPU reset can be performed
+	 * successfully. So now, temporarily enable it for the
+	 * S3 suspend abort case.
+	 */
+	if (((adev->apu_flags & AMD_APU_IS_RAVEN) ||
+	    (adev->apu_flags & AMD_APU_IS_RAVEN2)) &&
+		!soc15_need_reset_on_resume(adev))
 		return 0;
 
 	switch (soc15_asic_reset_method(adev)) {
@@ -689,7 +713,7 @@
 
 static void soc15_program_aspm(struct amdgpu_device *adev)
 {
-	if (!amdgpu_aspm)
+	if (!amdgpu_device_should_use_aspm(adev))
 		return;
 
 	if (!(adev->flags & AMD_IS_APU) &&
@@ -1273,8 +1297,11 @@
 				AMD_CG_SUPPORT_SDMA_LS |
 				AMD_CG_SUPPORT_VCN_MGCG;
 
+			/*
+			 * MMHUB PG needs to be disabled for Picasso for
+			 * stability reasons.
+			 */
 			adev->pg_flags = AMD_PG_SUPPORT_SDMA |
-				AMD_PG_SUPPORT_MMHUB |
 				AMD_PG_SUPPORT_VCN;
 		} else {
 			adev->cg_flags = AMD_CG_SUPPORT_GFX_MGCG |
@@ -1413,22 +1440,17 @@
 	return 0;
 }
 
-static void soc15_doorbell_range_init(struct amdgpu_device *adev)
+static void soc15_sdma_doorbell_range_init(struct amdgpu_device *adev)
 {
 	int i;
-	struct amdgpu_ring *ring;
 
-	/* sdma/ih doorbell range are programed by hypervisor */
+	/* sdma doorbell range is programed by hypervisor */
 	if (!amdgpu_sriov_vf(adev)) {
 		for (i = 0; i < adev->sdma.num_instances; i++) {
-			ring = &adev->sdma.instance[i].ring;
 			adev->nbio.funcs->sdma_doorbell_range(adev, i,
-				ring->use_doorbell, ring->doorbell_index,
+				true, adev->doorbell_index.sdma_engine[i] << 1,
 				adev->doorbell_index.sdma_doorbell_range);
 		}
-
-		adev->nbio.funcs->ih_doorbell_range(adev, adev->irq.ih.use_doorbell,
-						adev->irq.ih.doorbell_index);
 	}
 }
 
@@ -1453,10 +1475,11 @@
 	soc15_enable_doorbell_aperture(adev, true);
 	/* HW doorbell routing policy: doorbell writing not
 	 * in SDMA/IH/MM/ACV range will be routed to CP. So
-	 * we need to init SDMA/IH/MM/ACV doorbell range prior
-	 * to CP ip block init and ring test.
+	 * we need to init SDMA doorbell range prior
+	 * to CP ip block init and ring test.  IH already
+	 * happens before CP.
 	 */
-	soc15_doorbell_range_init(adev);
+	soc15_sdma_doorbell_range_init(adev);
 
 	return 0;
 }
@@ -1494,6 +1517,10 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	if (soc15_need_reset_on_resume(adev)) {
+		dev_info(adev->dev, "S3 suspend abort case, let's reset ASIC.\n");
+		soc15_asic_reset(adev);
+	}
 	return soc15_common_hw_init(adev);
 }
 
@@ -1615,9 +1642,11 @@
 	if (amdgpu_sriov_vf(adev))
 		*flags = 0;
 
-	adev->nbio.funcs->get_clockgating_state(adev, flags);
+	if (adev->nbio.funcs && adev->nbio.funcs->get_clockgating_state)
+		adev->nbio.funcs->get_clockgating_state(adev, flags);
 
-	adev->hdp.funcs->get_clock_gating_state(adev, flags);
+	if (adev->hdp.funcs && adev->hdp.funcs->get_clock_gating_state)
+		adev->hdp.funcs->get_clock_gating_state(adev, flags);
 
 	if (adev->asic_type != CHIP_ALDEBARAN) {
 
@@ -1633,9 +1662,11 @@
 	}
 
 	/* AMD_CG_SUPPORT_ROM_MGCG */
-	adev->smuio.funcs->get_clock_gating_state(adev, flags);
+	if (adev->smuio.funcs && adev->smuio.funcs->get_clock_gating_state)
+		adev->smuio.funcs->get_clock_gating_state(adev, flags);
 
-	adev->df.funcs->get_clockgating_state(adev, flags);
+	if (adev->df.funcs && adev->df.funcs->get_clockgating_state)
+		adev->df.funcs->get_clockgating_state(adev, flags);
 }
 
 static int soc15_common_set_powergating_state(void *handle,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/tonga_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/tonga_ih.c
@@ -219,6 +219,12 @@
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
 	WREG32(mmIH_RB_CNTL, tmp);
 
+	/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+	 * can be detected.
+	 */
+	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	WREG32(mmIH_RB_CNTL, tmp);
+
 out:
 	return (wptr & ih->ptr_mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/uvd_v3_1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/uvd_v3_1.c
@@ -698,6 +698,19 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->uvd.idle_work);
+
+	if (RREG32(mmUVD_STATUS) != 0)
+		uvd_v3_1_stop(adev);
+
+	return 0;
+}
+
+static int uvd_v3_1_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -722,17 +735,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	if (RREG32(mmUVD_STATUS) != 0)
-		uvd_v3_1_stop(adev);
-
-	return 0;
-}
-
-static int uvd_v3_1_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = uvd_v3_1_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/uvd_v4_2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/uvd_v4_2.c
@@ -212,6 +212,19 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->uvd.idle_work);
+
+	if (RREG32(mmUVD_STATUS) != 0)
+		uvd_v4_2_stop(adev);
+
+	return 0;
+}
+
+static int uvd_v4_2_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -236,17 +249,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	if (RREG32(mmUVD_STATUS) != 0)
-		uvd_v4_2_stop(adev);
-
-	return 0;
-}
-
-static int uvd_v4_2_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = uvd_v4_2_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/uvd_v5_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/uvd_v5_0.c
@@ -210,6 +210,19 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->uvd.idle_work);
+
+	if (RREG32(mmUVD_STATUS) != 0)
+		uvd_v5_0_stop(adev);
+
+	return 0;
+}
+
+static int uvd_v5_0_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -234,17 +247,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	if (RREG32(mmUVD_STATUS) != 0)
-		uvd_v5_0_stop(adev);
-
-	return 0;
-}
-
-static int uvd_v5_0_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = uvd_v5_0_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/uvd_v6_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/uvd_v6_0.c
@@ -543,6 +543,19 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->uvd.idle_work);
+
+	if (RREG32(mmUVD_STATUS) != 0)
+		uvd_v6_0_stop(adev);
+
+	return 0;
+}
+
+static int uvd_v6_0_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -567,17 +580,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	if (RREG32(mmUVD_STATUS) != 0)
-		uvd_v6_0_stop(adev);
-
-	return 0;
-}
-
-static int uvd_v6_0_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = uvd_v6_0_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/uvd_v7_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/uvd_v7_0.c
@@ -606,6 +606,23 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->uvd.idle_work);
+
+	if (!amdgpu_sriov_vf(adev))
+		uvd_v7_0_stop(adev);
+	else {
+		/* full access mode, so don't touch any UVD register */
+		DRM_DEBUG("For SRIOV client, shouldn't do anything.\n");
+	}
+
+	return 0;
+}
+
+static int uvd_v7_0_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -630,21 +647,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	if (!amdgpu_sriov_vf(adev))
-		uvd_v7_0_stop(adev);
-	else {
-		/* full access mode, so don't touch any UVD register */
-		DRM_DEBUG("For SRIOV client, shouldn't do anything.\n");
-	}
-
-	return 0;
-}
-
-static int uvd_v7_0_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = uvd_v7_0_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vce_v2_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vce_v2_0.c
@@ -479,6 +479,17 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->vce.idle_work);
+
+	return 0;
+}
+
+static int vce_v2_0_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -502,14 +513,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	return 0;
-}
-
-static int vce_v2_0_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = vce_v2_0_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vce_v3_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vce_v3_0.c
@@ -490,6 +490,21 @@
 	int r;
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
+	cancel_delayed_work_sync(&adev->vce.idle_work);
+
+	r = vce_v3_0_wait_for_idle(handle);
+	if (r)
+		return r;
+
+	vce_v3_0_stop(adev);
+	return vce_v3_0_set_clockgating_state(adev, AMD_CG_STATE_GATE);
+}
+
+static int vce_v3_0_suspend(void *handle)
+{
+	int r;
+	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+
 	/*
 	 * Proper cleanups before halting the HW engine:
 	 *   - cancel the delayed idle work
@@ -513,19 +528,6 @@
 						       AMD_CG_STATE_GATE);
 	}
 
-	r = vce_v3_0_wait_for_idle(handle);
-	if (r)
-		return r;
-
-	vce_v3_0_stop(adev);
-	return vce_v3_0_set_clockgating_state(adev, AMD_CG_STATE_GATE);
-}
-
-static int vce_v3_0_suspend(void *handle)
-{
-	int r;
-	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-
 	r = vce_v3_0_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vce_v4_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vce_v4_0.c
@@ -542,29 +542,8 @@
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 
-	/*
-	 * Proper cleanups before halting the HW engine:
-	 *   - cancel the delayed idle work
-	 *   - enable powergating
-	 *   - enable clockgating
-	 *   - disable dpm
-	 *
-	 * TODO: to align with the VCN implementation, move the
-	 * jobs for clockgating/powergating/dpm setting to
-	 * ->set_powergating_state().
-	 */
 	cancel_delayed_work_sync(&adev->vce.idle_work);
 
-	if (adev->pm.dpm_enabled) {
-		amdgpu_dpm_enable_vce(adev, false);
-	} else {
-		amdgpu_asic_set_vce_clocks(adev, 0, 0);
-		amdgpu_device_ip_set_powergating_state(adev, AMD_IP_BLOCK_TYPE_VCE,
-						       AMD_PG_STATE_GATE);
-		amdgpu_device_ip_set_clockgating_state(adev, AMD_IP_BLOCK_TYPE_VCE,
-						       AMD_CG_STATE_GATE);
-	}
-
 	if (!amdgpu_sriov_vf(adev)) {
 		/* vce_v4_0_wait_for_idle(handle); */
 		vce_v4_0_stop(adev);
@@ -594,6 +573,29 @@
 		drm_dev_exit(idx);
 	}
 
+	/*
+	 * Proper cleanups before halting the HW engine:
+	 *   - cancel the delayed idle work
+	 *   - enable powergating
+	 *   - enable clockgating
+	 *   - disable dpm
+	 *
+	 * TODO: to align with the VCN implementation, move the
+	 * jobs for clockgating/powergating/dpm setting to
+	 * ->set_powergating_state().
+	 */
+	cancel_delayed_work_sync(&adev->vce.idle_work);
+
+	if (adev->pm.dpm_enabled) {
+		amdgpu_dpm_enable_vce(adev, false);
+	} else {
+		amdgpu_asic_set_vce_clocks(adev, 0, 0);
+		amdgpu_device_ip_set_powergating_state(adev, AMD_IP_BLOCK_TYPE_VCE,
+						       AMD_PG_STATE_GATE);
+		amdgpu_device_ip_set_clockgating_state(adev, AMD_IP_BLOCK_TYPE_VCE,
+						       AMD_CG_STATE_GATE);
+	}
+
 	r = vce_v4_0_hw_fini(adev);
 	if (r)
 		return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vcn_v1_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vcn_v1_0.c
@@ -253,6 +253,13 @@
 {
 	int r;
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+	bool idle_work_unexecuted;
+
+	idle_work_unexecuted = cancel_delayed_work_sync(&adev->vcn.idle_work);
+	if (idle_work_unexecuted) {
+		if (adev->pm.dpm_enabled)
+			amdgpu_dpm_enable_uvd(adev, false);
+	}
 
 	r = vcn_v1_0_hw_fini(adev);
 	if (r)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/firmware.h>
+#include <drm/drm_drv.h>
 
 #include "amdgpu.h"
 #include "amdgpu_vcn.h"
@@ -192,11 +193,14 @@
  */
 static int vcn_v2_0_sw_fini(void *handle)
 {
-	int r;
+	int r, idx;
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 	volatile struct amdgpu_fw_shared *fw_shared = adev->vcn.inst->fw_shared_cpu_addr;
 
-	fw_shared->present_flag_0 = 0;
+	if (drm_dev_enter(&adev->ddev, &idx)) {
+		fw_shared->present_flag_0 = 0;
+		drm_dev_exit(idx);
+	}
 
 	amdgpu_virt_free_mm_table(adev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vcn_v2_5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vcn_v2_5.c
@@ -22,6 +22,7 @@
  */
 
 #include <linux/firmware.h>
+#include <drm/drm_drv.h>
 
 #include "amdgpu.h"
 #include "amdgpu_vcn.h"
@@ -233,17 +234,21 @@
  */
 static int vcn_v2_5_sw_fini(void *handle)
 {
-	int i, r;
+	int i, r, idx;
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
 	volatile struct amdgpu_fw_shared *fw_shared;
 
-	for (i = 0; i < adev->vcn.num_vcn_inst; i++) {
-		if (adev->vcn.harvest_config & (1 << i))
-			continue;
-		fw_shared = adev->vcn.inst[i].fw_shared_cpu_addr;
-		fw_shared->present_flag_0 = 0;
+	if (drm_dev_enter(&adev->ddev, &idx)) {
+		for (i = 0; i < adev->vcn.num_vcn_inst; i++) {
+			if (adev->vcn.harvest_config & (1 << i))
+				continue;
+			fw_shared = adev->vcn.inst[i].fw_shared_cpu_addr;
+			fw_shared->present_flag_0 = 0;
+		}
+		drm_dev_exit(idx);
 	}
 
+
 	if (amdgpu_sriov_vf(adev))
 		amdgpu_virt_free_mm_table(adev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vcn_v3_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vcn_v3_0.c
@@ -601,8 +601,8 @@
 			AMDGPU_GPU_PAGE_ALIGN(sizeof(struct amdgpu_fw_shared)), 0, indirect);
 
 	/* VCN global tiling registers */
-	WREG32_SOC15_DPG_MODE(0, SOC15_DPG_MODE_OFFSET(
-		UVD, 0, mmUVD_GFX10_ADDR_CONFIG), adev->gfx.config.gb_addr_config, 0, indirect);
+	WREG32_SOC15_DPG_MODE(inst_idx, SOC15_DPG_MODE_OFFSET(
+		UVD, inst_idx, mmUVD_GFX10_ADDR_CONFIG), adev->gfx.config.gb_addr_config, 0, indirect);
 }
 
 static void vcn_v3_0_disable_static_power_gating(struct amdgpu_device *adev, int inst)
@@ -1508,8 +1508,11 @@
 
 static int vcn_v3_0_stop_dpg_mode(struct amdgpu_device *adev, int inst_idx)
 {
+	struct dpg_pause_state state = {.fw_based = VCN_DPG_STATE__UNPAUSE};
 	uint32_t tmp;
 
+	vcn_v3_0_pause_dpg_mode(adev, inst_idx, &state);
+
 	/* Wait for power status to be 1 */
 	SOC15_WAIT_ON_RREG(VCN, inst_idx, mmUVD_POWER_STATUS, 1,
 		UVD_POWER_STATUS__UVD_POWER_STATUS_MASK);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vega10_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vega10_ih.c
@@ -289,6 +289,10 @@
 		}
 	}
 
+	if (!amdgpu_sriov_vf(adev))
+		adev->nbio.funcs->ih_doorbell_range(adev, adev->irq.ih.use_doorbell,
+						    adev->irq.ih.doorbell_index);
+
 	pci_set_master(adev->pdev);
 
 	/* enable interrupts */
@@ -367,6 +371,12 @@
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
 	WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
 
+	/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+	 * can be detected.
+	 */
+	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
+
 out:
 	return (wptr & ih->ptr_mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vega20_ih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vega20_ih.c
@@ -109,6 +109,33 @@
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, RB_ENABLE, (enable ? 1 : 0));
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, RB_GPU_TS_ENABLE, 1);
 
+	if (enable) {
+		/* Unset the CLEAR_OVERFLOW bit to make sure the next step
+		 * is switching the bit from 0 to 1
+		 */
+		tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+		if (amdgpu_sriov_vf(adev) && amdgpu_sriov_reg_indirect_ih(adev)) {
+			if (psp_reg_program(&adev->psp, ih_regs->psp_reg_id, tmp))
+				return -ETIMEDOUT;
+		} else {
+			WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
+		}
+
+		/* Clear RB_OVERFLOW bit */
+		tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
+		if (amdgpu_sriov_vf(adev) && amdgpu_sriov_reg_indirect_ih(adev)) {
+			if (psp_reg_program(&adev->psp, ih_regs->psp_reg_id, tmp))
+				return -ETIMEDOUT;
+		} else {
+			WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
+		}
+
+		/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+		 * can be detected.
+		 */
+		tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	}
+
 	/* enable_intr field is only valid in ring0 */
 	if (ih == &adev->irq.ih)
 		tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, ENABLE_INTR, (enable ? 1 : 0));
@@ -340,6 +367,10 @@
 		}
 	}
 
+	if (!amdgpu_sriov_vf(adev))
+		adev->nbio.funcs->ih_doorbell_range(adev, adev->irq.ih.use_doorbell,
+						    adev->irq.ih.doorbell_index);
+
 	pci_set_master(adev->pdev);
 
 	/* enable interrupts */
@@ -418,6 +449,12 @@
 	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 1);
 	WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
 
+	/* Unset the CLEAR_OVERFLOW bit immediately so new overflows
+	 * can be detected.
+	 */
+	tmp = REG_SET_FIELD(tmp, IH_RB_CNTL, WPTR_OVERFLOW_CLEAR, 0);
+	WREG32_NO_KIQ(ih_regs->ih_rb_cntl, tmp);
+
 out:
 	return (wptr & ih->ptr_mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdgpu/vi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdgpu/vi.c
@@ -542,8 +542,15 @@
 	u32 reference_clock = adev->clock.spll.reference_freq;
 	u32 tmp;
 
-	if (adev->flags & AMD_IS_APU)
-		return reference_clock;
+	if (adev->flags & AMD_IS_APU) {
+		switch (adev->asic_type) {
+		case CHIP_STONEY:
+			/* vbios says 48Mhz, but the actual freq is 100Mhz */
+			return 10000;
+		default:
+			return reference_clock;
+		}
+	}
 
 	tmp = RREG32_SMC(ixCG_CLKPIN_CNTL_2);
 	if (REG_GET_FIELD(tmp, CG_CLKPIN_CNTL_2, MUX_TCLK_TO_XCLK))
@@ -956,6 +963,10 @@
 {
 	int r;
 
+	/* APUs don't have full asic reset */
+	if (adev->flags & AMD_IS_APU)
+		return 0;
+
 	if (vi_asic_reset_method(adev) == AMD_RESET_METHOD_BACO) {
 		dev_info(adev->dev, "BACO reset\n");
 		r = amdgpu_dpm_baco_reset(adev);
@@ -1136,7 +1147,7 @@
 	bool bL1SS = false;
 	bool bClkReqSupport = true;
 
-	if (!amdgpu_aspm)
+	if (!amdgpu_device_should_use_aspm(adev) || !amdgpu_device_pcie_dynamic_switching_supported())
 		return;
 
 	if (adev->flags & AMD_IS_APU ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_chardev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_chardev.c
@@ -940,8 +940,8 @@
 	 * nodes, but not more than args->num_of_nodes as that is
 	 * the amount of memory allocated by user
 	 */
-	pa = kzalloc((sizeof(struct kfd_process_device_apertures) *
-				args->num_of_nodes), GFP_KERNEL);
+	pa = kcalloc(args->num_of_nodes, sizeof(struct kfd_process_device_apertures),
+		     GFP_KERNEL);
 	if (!pa)
 		return -ENOMEM;
 
@@ -1290,7 +1290,7 @@
 			goto err_unlock;
 		}
 		offset = amdgpu_amdkfd_get_mmio_remap_phys_addr(dev->kgd);
-		if (!offset) {
+		if (!offset || (PAGE_SIZE > 4096)) {
 			err = -ENOMEM;
 			goto err_unlock;
 		}
@@ -1807,13 +1807,9 @@
 	if (!args->start_addr || !args->size)
 		return -EINVAL;
 
-	mutex_lock(&p->mutex);
-
 	r = svm_ioctl(p, args->op, args->start_addr, args->size, args->nattr,
 		      args->attrs);
 
-	mutex_unlock(&p->mutex);
-
 	return r;
 }
 #else
@@ -2033,6 +2029,9 @@
 	if (vma->vm_end - vma->vm_start != PAGE_SIZE)
 		return -EINVAL;
 
+	if (PAGE_SIZE > 4096)
+		return -EINVAL;
+
 	address = amdgpu_amdkfd_get_mmio_remap_phys_addr(dev->kgd);
 
 	vma->vm_flags |= VM_IO | VM_DONTCOPY | VM_DONTEXPAND | VM_NORESERVE |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_crat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_crat.c
@@ -1060,6 +1060,9 @@
 			return -ENODEV;
 		/* same everything but the other direction */
 		props2 = kmemdup(props, sizeof(*props2), GFP_KERNEL);
+		if (!props2)
+			return -ENOMEM;
+
 		props2->node_from = id_to;
 		props2->node_to = id_from;
 		props2->kobj = NULL;
@@ -1560,7 +1563,7 @@
 	/* Fetch the CRAT table from ACPI */
 	status = acpi_get_table(CRAT_SIGNATURE, 0, &crat_table);
 	if (status == AE_NOT_FOUND) {
-		pr_warn("CRAT table not found\n");
+		pr_info("CRAT table not found\n");
 		return -ENODATA;
 	} else if (ACPI_FAILURE(status)) {
 		const char *err = acpi_format_exception(status);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_crat.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_crat.h
@@ -42,8 +42,6 @@
 #define CRAT_OEMTABLEID_LENGTH	8
 #define CRAT_RESERVED_LENGTH	6
 
-#define CRAT_OEMID_64BIT_MASK ((1ULL << (CRAT_OEMID_LENGTH * 8)) - 1)
-
 /* Compute Unit flags */
 #define COMPUTE_UNIT_CPU	(1 << 0)  /* Create Virtual CRAT for CPU */
 #define COMPUTE_UNIT_GPU	(1 << 1)  /* Create Virtual CRAT for GPU */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_device.c
@@ -834,15 +834,10 @@
 	}
 
 	/* Verify module parameters regarding mapped process number*/
-	if ((hws_max_conc_proc < 0)
-			|| (hws_max_conc_proc > kfd->vm_info.vmid_num_kfd)) {
-		dev_err(kfd_device,
-			"hws_max_conc_proc %d must be between 0 and %d, use %d instead\n",
-			hws_max_conc_proc, kfd->vm_info.vmid_num_kfd,
-			kfd->vm_info.vmid_num_kfd);
+	if (hws_max_conc_proc >= 0)
+		kfd->max_proc_per_quantum = min((u32)hws_max_conc_proc, kfd->vm_info.vmid_num_kfd);
+	else
 		kfd->max_proc_per_quantum = kfd->vm_info.vmid_num_kfd;
-	} else
-		kfd->max_proc_per_quantum = hws_max_conc_proc;
 
 	/* calculate max size of mqds needed for queues */
 	size = max_num_of_queues_per_device *
@@ -916,6 +911,7 @@
 	kfd_double_confirm_iommu_support(kfd);
 
 	if (kfd_iommu_device_init(kfd)) {
+		kfd->use_iommu_v2 = false;
 		dev_err(kfd_device, "Error initializing iommuv2\n");
 		goto device_iommu_error;
 	}
@@ -924,6 +920,9 @@
 
 	svm_migrate_init((struct amdgpu_device *)kfd->kgd);
 
+	if(kgd2kfd_resume_iommu(kfd))
+		goto device_iommu_error;
+
 	if (kfd_resume(kfd))
 		goto kfd_resume_error;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_device_queue_manager.c
@@ -138,19 +138,33 @@
 }
 
 static void increment_queue_count(struct device_queue_manager *dqm,
-			enum kfd_queue_type type)
+				  struct qcm_process_device *qpd,
+				  struct queue *q)
 {
 	dqm->active_queue_count++;
-	if (type == KFD_QUEUE_TYPE_COMPUTE || type == KFD_QUEUE_TYPE_DIQ)
+	if (q->properties.type == KFD_QUEUE_TYPE_COMPUTE ||
+	    q->properties.type == KFD_QUEUE_TYPE_DIQ)
 		dqm->active_cp_queue_count++;
+
+	if (q->properties.is_gws) {
+		dqm->gws_queue_count++;
+		qpd->mapped_gws_queue = true;
+	}
 }
 
 static void decrement_queue_count(struct device_queue_manager *dqm,
-			enum kfd_queue_type type)
+				  struct qcm_process_device *qpd,
+				  struct queue *q)
 {
 	dqm->active_queue_count--;
-	if (type == KFD_QUEUE_TYPE_COMPUTE || type == KFD_QUEUE_TYPE_DIQ)
+	if (q->properties.type == KFD_QUEUE_TYPE_COMPUTE ||
+	    q->properties.type == KFD_QUEUE_TYPE_DIQ)
 		dqm->active_cp_queue_count--;
+
+	if (q->properties.is_gws) {
+		dqm->gws_queue_count--;
+		qpd->mapped_gws_queue = false;
+	}
 }
 
 static int allocate_doorbell(struct qcm_process_device *qpd, struct queue *q)
@@ -390,7 +404,7 @@
 	list_add(&q->list, &qpd->queues_list);
 	qpd->queue_count++;
 	if (q->properties.is_active)
-		increment_queue_count(dqm, q->properties.type);
+		increment_queue_count(dqm, qpd, q);
 
 	/*
 	 * Unconditionally increment this counter, regardless of the queue's
@@ -515,13 +529,8 @@
 		deallocate_vmid(dqm, qpd, q);
 	}
 	qpd->queue_count--;
-	if (q->properties.is_active) {
-		decrement_queue_count(dqm, q->properties.type);
-		if (q->properties.is_gws) {
-			dqm->gws_queue_count--;
-			qpd->mapped_gws_queue = false;
-		}
-	}
+	if (q->properties.is_active)
+		decrement_queue_count(dqm, qpd, q);
 
 	return retval;
 }
@@ -613,12 +622,11 @@
 	 * dqm->active_queue_count to determine whether a new runlist must be
 	 * uploaded.
 	 */
-	if (q->properties.is_active && !prev_active)
-		increment_queue_count(dqm, q->properties.type);
-	else if (!q->properties.is_active && prev_active)
-		decrement_queue_count(dqm, q->properties.type);
-
-	if (q->gws && !q->properties.is_gws) {
+	if (q->properties.is_active && !prev_active) {
+		increment_queue_count(dqm, &pdd->qpd, q);
+	} else if (!q->properties.is_active && prev_active) {
+		decrement_queue_count(dqm, &pdd->qpd, q);
+	} else if (q->gws && !q->properties.is_gws) {
 		if (q->properties.is_active) {
 			dqm->gws_queue_count++;
 			pdd->qpd.mapped_gws_queue = true;
@@ -680,11 +688,7 @@
 		mqd_mgr = dqm->mqd_mgrs[get_mqd_type_from_queue_type(
 				q->properties.type)];
 		q->properties.is_active = false;
-		decrement_queue_count(dqm, q->properties.type);
-		if (q->properties.is_gws) {
-			dqm->gws_queue_count--;
-			qpd->mapped_gws_queue = false;
-		}
+		decrement_queue_count(dqm, qpd, q);
 
 		if (WARN_ONCE(!dqm->sched_running, "Evict when stopped\n"))
 			continue;
@@ -730,7 +734,7 @@
 			continue;
 
 		q->properties.is_active = false;
-		decrement_queue_count(dqm, q->properties.type);
+		decrement_queue_count(dqm, qpd, q);
 	}
 	pdd->last_evict_timestamp = get_jiffies_64();
 	retval = execute_queues_cpsch(dqm,
@@ -801,11 +805,7 @@
 		mqd_mgr = dqm->mqd_mgrs[get_mqd_type_from_queue_type(
 				q->properties.type)];
 		q->properties.is_active = true;
-		increment_queue_count(dqm, q->properties.type);
-		if (q->properties.is_gws) {
-			dqm->gws_queue_count++;
-			qpd->mapped_gws_queue = true;
-		}
+		increment_queue_count(dqm, qpd, q);
 
 		if (WARN_ONCE(!dqm->sched_running, "Restore when stopped\n"))
 			continue;
@@ -863,7 +863,7 @@
 			continue;
 
 		q->properties.is_active = true;
-		increment_queue_count(dqm, q->properties.type);
+		increment_queue_count(dqm, &pdd->qpd, q);
 	}
 	retval = execute_queues_cpsch(dqm,
 				KFD_UNMAP_QUEUES_FILTER_DYNAMIC_QUEUES, 0);
@@ -1225,6 +1225,11 @@
 	bool hanging;
 
 	dqm_lock(dqm);
+	if (!dqm->sched_running) {
+		dqm_unlock(dqm);
+		return 0;
+	}
+
 	if (!dqm->is_hws_hang)
 		unmap_queues_cpsch(dqm, KFD_UNMAP_QUEUES_FILTER_ALL_QUEUES, 0);
 	hanging = dqm->is_hws_hang || dqm->is_resetting;
@@ -1260,7 +1265,7 @@
 			dqm->total_queue_count);
 
 	list_add(&kq->list, &qpd->priv_queue_list);
-	increment_queue_count(dqm, kq->queue->properties.type);
+	increment_queue_count(dqm, qpd, kq->queue);
 	qpd->is_debug = true;
 	execute_queues_cpsch(dqm, KFD_UNMAP_QUEUES_FILTER_DYNAMIC_QUEUES, 0);
 	dqm_unlock(dqm);
@@ -1274,7 +1279,7 @@
 {
 	dqm_lock(dqm);
 	list_del(&kq->list);
-	decrement_queue_count(dqm, kq->queue->properties.type);
+	decrement_queue_count(dqm, qpd, kq->queue);
 	qpd->is_debug = false;
 	execute_queues_cpsch(dqm, KFD_UNMAP_QUEUES_FILTER_ALL_QUEUES, 0);
 	/*
@@ -1341,7 +1346,7 @@
 	qpd->queue_count++;
 
 	if (q->properties.is_active) {
-		increment_queue_count(dqm, q->properties.type);
+		increment_queue_count(dqm, qpd, q);
 
 		execute_queues_cpsch(dqm,
 				KFD_UNMAP_QUEUES_FILTER_DYNAMIC_QUEUES, 0);
@@ -1543,15 +1548,11 @@
 	list_del(&q->list);
 	qpd->queue_count--;
 	if (q->properties.is_active) {
-		decrement_queue_count(dqm, q->properties.type);
+		decrement_queue_count(dqm, qpd, q);
 		retval = execute_queues_cpsch(dqm,
 				KFD_UNMAP_QUEUES_FILTER_DYNAMIC_QUEUES, 0);
 		if (retval == -ETIME)
 			qpd->reset_wavefronts = true;
-		if (q->properties.is_gws) {
-			dqm->gws_queue_count--;
-			qpd->mapped_gws_queue = false;
-		}
 	}
 
 	/*
@@ -1742,7 +1743,7 @@
 	/* Clean all kernel queues */
 	list_for_each_entry_safe(kq, kq_next, &qpd->priv_queue_list, list) {
 		list_del(&kq->list);
-		decrement_queue_count(dqm, kq->queue->properties.type);
+		decrement_queue_count(dqm, qpd, kq->queue);
 		qpd->is_debug = false;
 		dqm->total_queue_count--;
 		filter = KFD_UNMAP_QUEUES_FILTER_ALL_QUEUES;
@@ -1755,13 +1756,8 @@
 		else if (q->properties.type == KFD_QUEUE_TYPE_SDMA_XGMI)
 			deallocate_sdma_queue(dqm, q);
 
-		if (q->properties.is_active) {
-			decrement_queue_count(dqm, q->properties.type);
-			if (q->properties.is_gws) {
-				dqm->gws_queue_count--;
-				qpd->mapped_gws_queue = false;
-			}
-		}
+		if (q->properties.is_active)
+			decrement_queue_count(dqm, qpd, q);
 
 		dqm->total_queue_count--;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_events.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_events.c
@@ -528,14 +528,13 @@
 	struct kfd_event_waiter *event_waiters;
 	uint32_t i;
 
-	event_waiters = kmalloc_array(num_events,
-					sizeof(struct kfd_event_waiter),
-					GFP_KERNEL);
+	event_waiters = kcalloc(num_events, sizeof(struct kfd_event_waiter),
+				GFP_KERNEL);
+	if (!event_waiters)
+		return NULL;
 
-	for (i = 0; (event_waiters) && (i < num_events) ; i++) {
+	for (i = 0; i < num_events; i++)
 		init_wait(&event_waiters[i].wait);
-		event_waiters[i].activated = false;
-	}
 
 	return event_waiters;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_migrate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_migrate.c
@@ -302,7 +302,7 @@
 			migrate->dst[i] = migrate_pfn(migrate->dst[i]);
 			migrate->dst[i] |= MIGRATE_PFN_LOCKED;
 			src[i] = dma_map_page(dev, spage, 0, PAGE_SIZE,
-					      DMA_TO_DEVICE);
+					      DMA_BIDIRECTIONAL);
 			r = dma_mapping_error(dev, src[i]);
 			if (r) {
 				pr_debug("failed %d dma_map_page\n", r);
@@ -569,7 +569,7 @@
 			goto out_oom;
 		}
 
-		dst[i] = dma_map_page(dev, dpage, 0, PAGE_SIZE, DMA_FROM_DEVICE);
+		dst[i] = dma_map_page(dev, dpage, 0, PAGE_SIZE, DMA_BIDIRECTIONAL);
 		r = dma_mapping_error(dev, dst[i]);
 		if (r) {
 			pr_debug("failed %d dma_map_page\n", r);
@@ -780,7 +780,7 @@
 static vm_fault_t svm_migrate_to_ram(struct vm_fault *vmf)
 {
 	unsigned long addr = vmf->address;
-	struct vm_area_struct *vma;
+	struct svm_range_bo *svm_bo;
 	enum svm_work_list_ops op;
 	struct svm_range *parent;
 	struct svm_range *prange;
@@ -788,24 +788,42 @@
 	struct mm_struct *mm;
 	int r = 0;
 
-	vma = vmf->vma;
-	mm = vma->vm_mm;
+	svm_bo = vmf->page->zone_device_data;
+	if (!svm_bo) {
+		pr_debug("failed get device page at addr 0x%lx\n", addr);
+		return VM_FAULT_SIGBUS;
+	}
+	if (!mmget_not_zero(svm_bo->eviction_fence->mm)) {
+		pr_debug("addr 0x%lx of process mm is detroyed\n", addr);
+		return VM_FAULT_SIGBUS;
+	}
 
-	p = kfd_lookup_process_by_mm(vma->vm_mm);
+	mm = svm_bo->eviction_fence->mm;
+	if (mm != vmf->vma->vm_mm)
+		pr_debug("addr 0x%lx is COW mapping in child process\n", addr);
+
+	p = kfd_lookup_process_by_mm(mm);
 	if (!p) {
 		pr_debug("failed find process at fault address 0x%lx\n", addr);
-		return VM_FAULT_SIGBUS;
+		r = VM_FAULT_SIGBUS;
+		goto out_mmput;
 	}
-	addr >>= PAGE_SHIFT;
+	if (READ_ONCE(p->svms.faulting_task) == current) {
+		pr_debug("skipping ram migration\n");
+		r = 0;
+		goto out_unref_process;
+	}
+
 	pr_debug("CPU page fault svms 0x%p address 0x%lx\n", &p->svms, addr);
+	addr >>= PAGE_SHIFT;
 
 	mutex_lock(&p->svms.lock);
 
 	prange = svm_range_from_addr(&p->svms, addr, &parent);
 	if (!prange) {
-		pr_debug("cannot find svm range at 0x%lx\n", addr);
+		pr_debug("failed get range svms 0x%p addr 0x%lx\n", &p->svms, addr);
 		r = -EFAULT;
-		goto out;
+		goto out_unlock_svms;
 	}
 
 	mutex_lock(&parent->migrate_mutex);
@@ -827,10 +845,10 @@
 		goto out_unlock_prange;
 	}
 
-	r = svm_migrate_vram_to_ram(prange, mm);
+	r = svm_migrate_vram_to_ram(prange, vmf->vma->vm_mm);
 	if (r)
-		pr_debug("failed %d migrate 0x%p [0x%lx 0x%lx] to ram\n", r,
-			 prange, prange->start, prange->last);
+		pr_debug("failed %d migrate svms 0x%p range 0x%p [0x%lx 0x%lx]\n",
+			 r, prange->svms, prange, prange->start, prange->last);
 
 	/* xnack on, update mapping on GPUs with ACCESS_IN_PLACE */
 	if (p->xnack_enabled && parent == prange)
@@ -844,12 +862,13 @@
 	if (prange != parent)
 		mutex_unlock(&prange->migrate_mutex);
 	mutex_unlock(&parent->migrate_mutex);
-out:
+out_unlock_svms:
 	mutex_unlock(&p->svms.lock);
-	kfd_unref_process(p);
-
+out_unref_process:
 	pr_debug("CPU fault svms 0x%p address 0x%lx done\n", &p->svms, addr);
-
+	kfd_unref_process(p);
+out_mmput:
+	mmput(mm);
 	return r ? VM_FAULT_SIGBUS : 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_mqd_manager_v9.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_mqd_manager_v9.c
@@ -113,18 +113,19 @@
 			&(mqd_mem_obj->gtt_mem),
 			&(mqd_mem_obj->gpu_addr),
 			(void *)&(mqd_mem_obj->cpu_ptr), true);
+
+		if (retval) {
+			kfree(mqd_mem_obj);
+			return NULL;
+		}
 	} else {
 		retval = kfd_gtt_sa_allocate(kfd, sizeof(struct v9_mqd),
 				&mqd_mem_obj);
-	}
-
-	if (retval) {
-		kfree(mqd_mem_obj);
-		return NULL;
+		if (retval)
+			return NULL;
 	}
 
 	return mqd_mem_obj;
-
 }
 
 static void init_mqd(struct mqd_manager *mm, void **mqd,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_priv.h
@@ -755,6 +755,7 @@
 	atomic_t			evicted_ranges;
 	struct delayed_work		restore_work;
 	DECLARE_BITMAP(bitmap_supported, MAX_GPU_INSTANCE);
+	struct task_struct 		*faulting_task;
 };
 
 /* Process data */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_process.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_process.c
@@ -311,8 +311,8 @@
 							      attr_sdma);
 		struct kfd_sdma_activity_handler_workarea sdma_activity_work_handler;
 
-		INIT_WORK(&sdma_activity_work_handler.sdma_activity_work,
-					kfd_sdma_activity_worker);
+		INIT_WORK_ONSTACK(&sdma_activity_work_handler.sdma_activity_work,
+				  kfd_sdma_activity_worker);
 
 		sdma_activity_work_handler.pdd = pdd;
 		sdma_activity_work_handler.sdma_activity_counter = 0;
@@ -320,6 +320,7 @@
 		schedule_work(&sdma_activity_work_handler.sdma_activity_work);
 
 		flush_work(&sdma_activity_work_handler.sdma_activity_work);
+		destroy_work_on_stack(&sdma_activity_work_handler.sdma_activity_work);
 
 		return snprintf(buffer, PAGE_SIZE, "%llu\n",
 				(sdma_activity_work_handler.sdma_activity_counter)/
@@ -818,6 +819,14 @@
 	if (process) {
 		pr_debug("Process already found\n");
 	} else {
+		/* If the process just called exec(3), it is possible that the
+		 * cleanup of the kfd_process (following the release of the mm
+		 * of the old process image) is still in the cleanup work queue.
+		 * Make sure to drain any job before trying to recreate any
+		 * resource for this process.
+		 */
+		flush_workqueue(kfd_process_wq);
+
 		process = create_process(thread);
 		if (IS_ERR(process))
 			goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_smi_events.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_smi_events.c
@@ -270,15 +270,6 @@
 		return ret;
 	}
 
-	ret = anon_inode_getfd(kfd_smi_name, &kfd_smi_ev_fops, (void *)client,
-			       O_RDWR);
-	if (ret < 0) {
-		kfifo_free(&client->fifo);
-		kfree(client);
-		return ret;
-	}
-	*fd = ret;
-
 	init_waitqueue_head(&client->wait_queue);
 	spin_lock_init(&client->lock);
 	client->events = 0;
@@ -288,5 +279,20 @@
 	list_add_rcu(&client->list, &dev->smi_clients);
 	spin_unlock(&dev->smi_lock);
 
+	ret = anon_inode_getfd(kfd_smi_name, &kfd_smi_ev_fops, (void *)client,
+			       O_RDWR);
+	if (ret < 0) {
+		spin_lock(&dev->smi_lock);
+		list_del_rcu(&client->list);
+		spin_unlock(&dev->smi_lock);
+
+		synchronize_rcu();
+
+		kfifo_free(&client->fifo);
+		kfree(client);
+		return ret;
+	}
+	*fd = ret;
+
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_svm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_svm.c
@@ -347,14 +347,9 @@
 		spin_lock(&svm_bo->list_lock);
 	}
 	spin_unlock(&svm_bo->list_lock);
-	if (!dma_fence_is_signaled(&svm_bo->eviction_fence->base)) {
-		/* We're not in the eviction worker.
-		 * Signal the fence and synchronize with any
-		 * pending eviction work.
-		 */
+	if (!dma_fence_is_signaled(&svm_bo->eviction_fence->base))
+		/* We're not in the eviction worker. Signal the fence. */
 		dma_fence_signal(&svm_bo->eviction_fence->base);
-		cancel_work_sync(&svm_bo->eviction_work);
-	}
 	dma_fence_put(&svm_bo->eviction_fence->base);
 	amdgpu_bo_unref(&svm_bo->bo);
 	kfree(svm_bo);
@@ -433,11 +428,11 @@
 
 	/* We need a new svm_bo. Spin-loop to wait for concurrent
 	 * svm_range_bo_release to finish removing this range from
-	 * its range list. After this, it is safe to reuse the
-	 * svm_bo pointer and svm_bo_list head.
+	 * its range list and set prange->svm_bo to null. After this,
+	 * it is safe to reuse the svm_bo pointer and svm_bo_list head.
 	 */
-	while (!list_empty_careful(&prange->svm_bo_list))
-		;
+	while (!list_empty_careful(&prange->svm_bo_list) || prange->svm_bo)
+		cond_resched();
 
 	return false;
 }
@@ -550,8 +545,15 @@
 
 void svm_range_vram_node_free(struct svm_range *prange)
 {
-	svm_range_bo_unref(prange->svm_bo);
-	prange->ttm_res = NULL;
+	/* serialize prange->svm_bo unref */
+	mutex_lock(&prange->lock);
+	/* prange->svm_bo has not been unref */
+	if (prange->ttm_res) {
+		prange->ttm_res = NULL;
+		mutex_unlock(&prange->lock);
+		svm_range_bo_unref(prange->svm_bo);
+	} else
+		mutex_unlock(&prange->lock);
 }
 
 struct amdgpu_device *
@@ -691,7 +693,7 @@
 			prange->flags &= ~attrs[i].value;
 			break;
 		case KFD_IOCTL_SVM_ATTR_GRANULARITY:
-			prange->granularity = attrs[i].value;
+			prange->granularity = min_t(uint32_t, attrs[i].value, 0x3F);
 			break;
 		default:
 			WARN_ONCE(1, "svm_range_check_attrs wasn't called?");
@@ -936,7 +938,7 @@
 }
 
 static int
-svm_range_split_tail(struct svm_range *prange, struct svm_range *new,
+svm_range_split_tail(struct svm_range *prange,
 		     uint64_t new_last, struct list_head *insert_list)
 {
 	struct svm_range *tail;
@@ -948,7 +950,7 @@
 }
 
 static int
-svm_range_split_head(struct svm_range *prange, struct svm_range *new,
+svm_range_split_head(struct svm_range *prange,
 		     uint64_t new_start, struct list_head *insert_list)
 {
 	struct svm_range *head;
@@ -1307,7 +1309,7 @@
 	struct svm_range *prange;
 	bool intr;
 	unsigned long bitmap[MAX_GPU_INSTANCE];
-	struct ttm_validate_buffer tv[MAX_GPU_INSTANCE+1];
+	struct ttm_validate_buffer tv[MAX_GPU_INSTANCE];
 	struct list_head validate_list;
 	struct ww_acquire_ctx ticket;
 };
@@ -1334,11 +1336,6 @@
 		ctx->tv[gpuidx].num_shared = 4;
 		list_add(&ctx->tv[gpuidx].head, &ctx->validate_list);
 	}
-	if (ctx->prange->svm_bo && ctx->prange->ttm_res) {
-		ctx->tv[MAX_GPU_INSTANCE].bo = &ctx->prange->svm_bo->bo->tbo;
-		ctx->tv[MAX_GPU_INSTANCE].num_shared = 1;
-		list_add(&ctx->tv[MAX_GPU_INSTANCE].head, &ctx->validate_list);
-	}
 
 	r = ttm_eu_reserve_buffers(&ctx->ticket, &ctx->validate_list,
 				   ctx->intr, NULL);
@@ -1494,9 +1491,11 @@
 
 		next = min(vma->vm_end, end);
 		npages = (next - addr) >> PAGE_SHIFT;
+		WRITE_ONCE(p->svms.faulting_task, current);
 		r = amdgpu_hmm_range_get_pages(&prange->notifier, mm, NULL,
 					       addr, npages, &hmm_range,
 					       readonly, true, owner);
+		WRITE_ONCE(p->svms.faulting_task, NULL);
 		if (r) {
 			pr_debug("failed %d to get svm range pages\n", r);
 			goto unreserve_out;
@@ -1570,7 +1569,6 @@
 static void svm_range_restore_work(struct work_struct *work)
 {
 	struct delayed_work *dwork = to_delayed_work(work);
-	struct amdkfd_process_info *process_info;
 	struct svm_range_list *svms;
 	struct svm_range *prange;
 	struct kfd_process *p;
@@ -1590,12 +1588,10 @@
 	 * the lifetime of this thread, kfd_process and mm will be valid.
 	 */
 	p = container_of(svms, struct kfd_process, svms);
-	process_info = p->kgd_process_info;
 	mm = p->mm;
 	if (!mm)
 		return;
 
-	mutex_lock(&process_info->lock);
 	svm_range_list_lock_and_flush_work(svms, mm);
 	mutex_lock(&svms->lock);
 
@@ -1648,7 +1644,6 @@
 out_reschedule:
 	mutex_unlock(&svms->lock);
 	mmap_write_unlock(mm);
-	mutex_unlock(&process_info->lock);
 
 	/* If validation failed, reschedule another attempt */
 	if (evicted_ranges) {
@@ -1764,49 +1759,54 @@
 }
 
 /**
- * svm_range_handle_overlap - split overlap ranges
- * @svms: svm range list header
- * @new: range added with this attributes
- * @start: range added start address, in pages
- * @last: range last address, in pages
- * @update_list: output, the ranges attributes are updated. For set_attr, this
- *               will do validation and map to GPUs. For unmap, this will be
- *               removed and unmap from GPUs
- * @insert_list: output, the ranges will be inserted into svms, attributes are
- *               not changes. For set_attr, this will add into svms.
- * @remove_list:output, the ranges will be removed from svms
- * @left: the remaining range after overlap, For set_attr, this will be added
- *        as new range.
- *
- * Total have 5 overlap cases.
- *
- * This function handles overlap of an address interval with existing
- * struct svm_ranges for applying new attributes. This may require
- * splitting existing struct svm_ranges. All changes should be applied to
- * the range_list and interval tree transactionally. If any split operation
- * fails, the entire update fails. Therefore the existing overlapping
- * svm_ranges are cloned and the original svm_ranges left unchanged. If the
- * transaction succeeds, the modified clones are added and the originals
- * freed. Otherwise the clones are removed and the old svm_ranges remain.
+ * svm_range_add - add svm range and handle overlap
+ * @p: the range add to this process svms
+ * @start: page size aligned
+ * @size: page size aligned
+ * @nattr: number of attributes
+ * @attrs: array of attributes
+ * @update_list: output, the ranges need validate and update GPU mapping
+ * @insert_list: output, the ranges need insert to svms
+ * @remove_list: output, the ranges are replaced and need remove from svms
  *
- * Context: The caller must hold svms->lock
+ * Check if the virtual address range has overlap with any existing ranges,
+ * split partly overlapping ranges and add new ranges in the gaps. All changes
+ * should be applied to the range_list and interval tree transactionally. If
+ * any range split or allocation fails, the entire update fails. Therefore any
+ * existing overlapping svm_ranges are cloned and the original svm_ranges left
+ * unchanged.
+ *
+ * If the transaction succeeds, the caller can update and insert clones and
+ * new ranges, then free the originals.
+ *
+ * Otherwise the caller can free the clones and new ranges, while the old
+ * svm_ranges remain unchanged.
+ *
+ * Context: Process context, caller must hold svms->lock
+ *
+ * Return:
+ * 0 - OK, otherwise error code
  */
 static int
-svm_range_handle_overlap(struct svm_range_list *svms, struct svm_range *new,
-			 unsigned long start, unsigned long last,
-			 struct list_head *update_list,
-			 struct list_head *insert_list,
-			 struct list_head *remove_list,
-			 unsigned long *left)
+svm_range_add(struct kfd_process *p, uint64_t start, uint64_t size,
+	      uint32_t nattr, struct kfd_ioctl_svm_attribute *attrs,
+	      struct list_head *update_list, struct list_head *insert_list,
+	      struct list_head *remove_list)
 {
+	unsigned long last = start + size - 1UL;
+	struct svm_range_list *svms = &p->svms;
 	struct interval_tree_node *node;
+	struct svm_range new = {0};
 	struct svm_range *prange;
 	struct svm_range *tmp;
 	int r = 0;
 
+	pr_debug("svms 0x%p [0x%llx 0x%lx]\n", &p->svms, start, last);
+
 	INIT_LIST_HEAD(update_list);
 	INIT_LIST_HEAD(insert_list);
 	INIT_LIST_HEAD(remove_list);
+	svm_range_apply_attrs(p, &new, nattr, attrs);
 
 	node = interval_tree_iter_first(&svms->objects, start, last);
 	while (node) {
@@ -1834,14 +1834,14 @@
 
 			if (node->start < start) {
 				pr_debug("change old range start\n");
-				r = svm_range_split_head(prange, new, start,
+				r = svm_range_split_head(prange, start,
 							 insert_list);
 				if (r)
 					goto out;
 			}
 			if (node->last > last) {
 				pr_debug("change old range last\n");
-				r = svm_range_split_tail(prange, new, last,
+				r = svm_range_split_tail(prange, last,
 							 insert_list);
 				if (r)
 					goto out;
@@ -1853,7 +1853,7 @@
 			prange = old;
 		}
 
-		if (!svm_range_is_same_attrs(prange, new))
+		if (!svm_range_is_same_attrs(prange, &new))
 			list_add(&prange->update_list, update_list);
 
 		/* insert a new node if needed */
@@ -1873,8 +1873,16 @@
 		start = next_start;
 	}
 
-	if (left && start <= last)
-		*left = last - start + 1;
+	/* add a final range at the end if needed */
+	if (start <= last) {
+		prange = svm_range_new(svms, start, last);
+		if (!prange) {
+			r = -ENOMEM;
+			goto out;
+		}
+		list_add(&prange->insert_list, insert_list);
+		list_add(&prange->update_list, update_list);
+	}
 
 out:
 	if (r)
@@ -2177,6 +2185,8 @@
 
 	if (range->event == MMU_NOTIFY_RELEASE)
 		return true;
+	if (!mmget_not_zero(mni->mm))
+		return true;
 
 	start = mni->interval_tree.start;
 	last = mni->interval_tree.last;
@@ -2203,6 +2213,7 @@
 	}
 
 	svm_range_unlock(prange);
+	mmput(mni->mm);
 
 	return true;
 }
@@ -2314,6 +2325,7 @@
 {
 	struct vm_area_struct *vma;
 	struct interval_tree_node *node;
+	struct rb_node *rb_node;
 	unsigned long start_limit, end_limit;
 
 	vma = find_vma(p->mm, addr << PAGE_SHIFT);
@@ -2330,16 +2342,15 @@
 	if (node) {
 		end_limit = min(end_limit, node->start);
 		/* Last range that ends before the fault address */
-		node = container_of(rb_prev(&node->rb),
-				    struct interval_tree_node, rb);
+		rb_node = rb_prev(&node->rb);
 	} else {
 		/* Last range must end before addr because
 		 * there was no range after addr
 		 */
-		node = container_of(rb_last(&p->svms.objects.rb_root),
-				    struct interval_tree_node, rb);
+		rb_node = rb_last(&p->svms.objects.rb_root);
 	}
-	if (node) {
+	if (rb_node) {
+		node = container_of(rb_node, struct interval_tree_node, rb);
 		if (node->last >= addr) {
 			WARN(1, "Overlap with prev node and page fault addr\n");
 			return -EFAULT;
@@ -2703,59 +2714,6 @@
 }
 
 /**
- * svm_range_add - add svm range and handle overlap
- * @p: the range add to this process svms
- * @start: page size aligned
- * @size: page size aligned
- * @nattr: number of attributes
- * @attrs: array of attributes
- * @update_list: output, the ranges need validate and update GPU mapping
- * @insert_list: output, the ranges need insert to svms
- * @remove_list: output, the ranges are replaced and need remove from svms
- *
- * Check if the virtual address range has overlap with the registered ranges,
- * split the overlapped range, copy and adjust pages address and vram nodes in
- * old and new ranges.
- *
- * Context: Process context, caller must hold svms->lock
- *
- * Return:
- * 0 - OK, otherwise error code
- */
-static int
-svm_range_add(struct kfd_process *p, uint64_t start, uint64_t size,
-	      uint32_t nattr, struct kfd_ioctl_svm_attribute *attrs,
-	      struct list_head *update_list, struct list_head *insert_list,
-	      struct list_head *remove_list)
-{
-	uint64_t last = start + size - 1UL;
-	struct svm_range_list *svms;
-	struct svm_range new = {0};
-	struct svm_range *prange;
-	unsigned long left = 0;
-	int r = 0;
-
-	pr_debug("svms 0x%p [0x%llx 0x%llx]\n", &p->svms, start, last);
-
-	svm_range_apply_attrs(p, &new, nattr, attrs);
-
-	svms = &p->svms;
-
-	r = svm_range_handle_overlap(svms, &new, start, last, update_list,
-				     insert_list, remove_list, &left);
-	if (r)
-		return r;
-
-	if (left) {
-		prange = svm_range_new(svms, last - left + 1, last);
-		list_add(&prange->insert_list, insert_list);
-		list_add(&prange->update_list, update_list);
-	}
-
-	return 0;
-}
-
-/**
  * svm_range_best_prefetch_location - decide the best prefetch location
  * @prange: svm range structure
  *
@@ -2909,13 +2867,14 @@
 
 int svm_range_schedule_evict_svm_bo(struct amdgpu_amdkfd_fence *fence)
 {
-	if (!fence)
-		return -EINVAL;
-
-	if (dma_fence_is_signaled(&fence->base))
-		return 0;
-
-	if (fence->svm_bo) {
+	/* Dereferencing fence->svm_bo is safe here because the fence hasn't
+	 * signaled yet and we're under the protection of the fence->lock.
+	 * After the fence is signaled in svm_range_bo_release, we cannot get
+	 * here any more.
+	 *
+	 * Reference is dropped in svm_range_evict_svm_bo_worker.
+	 */
+	if (svm_bo_ref_unless_zero(fence->svm_bo)) {
 		WRITE_ONCE(fence->svm_bo->evicting, 1);
 		schedule_work(&fence->svm_bo->eviction_work);
 	}
@@ -2930,8 +2889,6 @@
 	struct mm_struct *mm;
 
 	svm_bo = container_of(work, struct svm_range_bo, eviction_work);
-	if (!svm_bo_ref_unless_zero(svm_bo))
-		return; /* svm_bo was freed while eviction was pending */
 
 	/* svm_range_bo_release destroys this worker thread. So during
 	 * the lifetime of this thread, kfd_process and mm will be valid.
@@ -2979,7 +2936,6 @@
 svm_range_set_attr(struct kfd_process *p, uint64_t start, uint64_t size,
 		   uint32_t nattr, struct kfd_ioctl_svm_attribute *attrs)
 {
-	struct amdkfd_process_info *process_info = p->kgd_process_info;
 	struct mm_struct *mm = current->mm;
 	struct list_head update_list;
 	struct list_head insert_list;
@@ -2998,8 +2954,6 @@
 
 	svms = &p->svms;
 
-	mutex_lock(&process_info->lock);
-
 	svm_range_list_lock_and_flush_work(svms, mm);
 
 	if (!svm_range_is_valid(mm, start, size)) {
@@ -3075,8 +3029,6 @@
 	mutex_unlock(&svms->lock);
 	mmap_read_unlock(mm);
 out:
-	mutex_unlock(&process_info->lock);
-
 	pr_debug("pasid 0x%x svms 0x%p [0x%llx 0x%llx] done, r=%d\n", p->pasid,
 		 &p->svms, start, start + size - 1, r);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_topology.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_topology.c
@@ -910,8 +910,7 @@
 	dev = list_last_entry(&topology_device_list,
 			struct kfd_topology_device, list);
 	if (dev) {
-		sys_props.platform_id =
-			(*((uint64_t *)dev->oem_id)) & CRAT_OEMID_64BIT_MASK;
+		sys_props.platform_id = dev->oem_id64;
 		sys_props.platform_oem = *((uint64_t *)dev->oem_table_id);
 		sys_props.platform_rev = dev->oem_revision;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/amdkfd/kfd_topology.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/amdkfd/kfd_topology.h
@@ -184,7 +184,10 @@
 	struct attribute		attr_gpuid;
 	struct attribute		attr_name;
 	struct attribute		attr_props;
-	uint8_t				oem_id[CRAT_OEMID_LENGTH];
+	union {
+		uint8_t				oem_id[CRAT_OEMID_LENGTH];
+		uint64_t			oem_id64;
+	};
 	uint8_t				oem_table_id[CRAT_OEMTABLEID_LENGTH];
 	uint32_t			oem_revision;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/Kconfig
@@ -5,6 +5,7 @@
 config DRM_AMD_DC
 	bool "AMD DC - Enable new display engine"
 	default y
+	depends on BROKEN || !CC_IS_CLANG || X86_64 || SPARC64 || ARM64
 	select SND_HDA_COMPONENT if SND_HDA_CORE
 	select DRM_AMD_DC_DCN if (X86 || PPC64) && !(KCOV_INSTRUMENT_ALL && KCOV_ENABLE_COMPARISONS)
 	help
@@ -12,6 +13,12 @@
 	  support for AMDGPU. This adds required support for Vega and
 	  Raven ASICs.
 
+	  calculate_bandwidth() is presently broken on all !(X86_64 || SPARC64 || ARM64)
+	  architectures built with Clang (all released versions), whereby the stack
+	  frame gets blown up to well over 5k.  This would cause an immediate kernel
+	  panic on most architectures.  We'll revert this when the following bug report
+	  has been resolved: https://github.com/llvm/llvm-project/issues/41896.
+
 config DRM_AMD_DC_DCN
 	def_bool n
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c
@@ -29,6 +29,7 @@
 #include "dm_services_types.h"
 #include "dc.h"
 #include "dc_link_dp.h"
+#include "link_enc_cfg.h"
 #include "dc/inc/core_types.h"
 #include "dal_asic_id.h"
 #include "dmub/dmub_srv.h"
@@ -70,6 +71,7 @@
 #include <linux/pci.h>
 #include <linux/firmware.h>
 #include <linux/component.h>
+#include <linux/dmi.h>
 
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_uapi.h>
@@ -215,6 +217,13 @@
 static const struct drm_format_info *
 amd_get_format_info(const struct drm_mode_fb_cmd2 *cmd);
 
+static void handle_hpd_irq_helper(struct amdgpu_dm_connector *aconnector);
+static void handle_hpd_rx_irq(void *param);
+
+static void amdgpu_dm_backlight_set_level(struct amdgpu_display_manager *dm,
+					 int bl_idx,
+					 u32 user_brightness);
+
 static bool
 is_timing_unchanged_for_freesync(struct drm_crtc_state *old_crtc_state,
 				 struct drm_crtc_state *new_crtc_state);
@@ -351,6 +360,35 @@
 }
 
 /**
+ * update_planes_and_stream_adapter() - Send planes to be updated in DC
+ *
+ * DC has a generic way to update planes and stream via
+ * dc_update_planes_and_stream function; however, DM might need some
+ * adjustments and preparation before calling it. This function is a wrapper
+ * for the dc_update_planes_and_stream that does any required configuration
+ * before passing control to DC.
+ */
+static inline bool update_planes_and_stream_adapter(struct dc *dc,
+						    int update_type,
+						    int planes_count,
+						    struct dc_stream_state *stream,
+						    struct dc_stream_update *stream_update,
+						    struct dc_surface_update *array_of_surface_update)
+{
+	/*
+	 * Previous frame finished and HW is ready for optimization.
+	 */
+	if (update_type == UPDATE_TYPE_FAST)
+		dc_post_update_surfaces_to_stream(dc);
+
+	return dc_update_planes_and_stream(dc,
+					   array_of_surface_update,
+					   planes_count,
+					   stream,
+					   stream_update);
+}
+
+/**
  * dm_pflip_high_irq() - Handle pageflip interrupt
  * @interrupt_params: ignored
  *
@@ -618,6 +656,128 @@
 }
 #endif
 
+/**
+ * dmub_aux_setconfig_reply_callback - Callback for AUX or SET_CONFIG command.
+ * @adev: amdgpu_device pointer
+ * @notify: dmub notification structure
+ *
+ * Dmub AUX or SET_CONFIG command completion processing callback
+ * Copies dmub notification to DM which is to be read by AUX command.
+ * issuing thread and also signals the event to wake up the thread.
+ */
+void dmub_aux_setconfig_callback(struct amdgpu_device *adev, struct dmub_notification *notify)
+{
+	if (adev->dm.dmub_notify)
+		memcpy(adev->dm.dmub_notify, notify, sizeof(struct dmub_notification));
+	if (notify->type == DMUB_NOTIFICATION_AUX_REPLY)
+		complete(&adev->dm.dmub_aux_transfer_done);
+}
+
+/**
+ * dmub_hpd_callback - DMUB HPD interrupt processing callback.
+ * @adev: amdgpu_device pointer
+ * @notify: dmub notification structure
+ *
+ * Dmub Hpd interrupt processing callback. Gets displayindex through the
+ * ink index and calls helper to do the processing.
+ */
+void dmub_hpd_callback(struct amdgpu_device *adev, struct dmub_notification *notify)
+{
+	struct amdgpu_dm_connector *aconnector;
+	struct amdgpu_dm_connector *hpd_aconnector = NULL;
+	struct drm_connector *connector;
+	struct drm_connector_list_iter iter;
+	struct dc_link *link;
+	uint8_t link_index = 0;
+	struct drm_device *dev;
+
+	if (adev == NULL)
+		return;
+
+	if (notify == NULL) {
+		DRM_ERROR("DMUB HPD callback notification was NULL");
+		return;
+	}
+
+	if (notify->link_index > adev->dm.dc->link_count) {
+		DRM_ERROR("DMUB HPD index (%u)is abnormal", notify->link_index);
+		return;
+	}
+
+	/* Skip DMUB HPD IRQ in suspend/resume. We will probe them later. */
+	if (notify->type == DMUB_NOTIFICATION_HPD && adev->in_suspend) {
+		DRM_INFO("Skip DMUB HPD IRQ callback in suspend/resume\n");
+		return;
+	}
+
+	link_index = notify->link_index;
+	link = adev->dm.dc->links[link_index];
+	dev = adev->dm.ddev;
+
+	drm_connector_list_iter_begin(dev, &iter);
+	drm_for_each_connector_iter(connector, &iter) {
+		aconnector = to_amdgpu_dm_connector(connector);
+		if (link && aconnector->dc_link == link) {
+			DRM_INFO("DMUB HPD callback: link_index=%u\n", link_index);
+			hpd_aconnector = aconnector;
+			break;
+		}
+	}
+	drm_connector_list_iter_end(&iter);
+
+	if (hpd_aconnector) {
+		if (notify->type == DMUB_NOTIFICATION_HPD)
+			handle_hpd_irq_helper(hpd_aconnector);
+		else if (notify->type == DMUB_NOTIFICATION_HPD_IRQ)
+			handle_hpd_rx_irq(hpd_aconnector);
+	}
+}
+
+/**
+ * register_dmub_notify_callback - Sets callback for DMUB notify
+ * @adev: amdgpu_device pointer
+ * @type: Type of dmub notification
+ * @callback: Dmub interrupt callback function
+ * @dmub_int_thread_offload: offload indicator
+ *
+ * API to register a dmub callback handler for a dmub notification
+ * Also sets indicator whether callback processing to be offloaded.
+ * to dmub interrupt handling thread
+ * Return: true if successfully registered, false if there is existing registration
+ */
+bool register_dmub_notify_callback(struct amdgpu_device *adev, enum dmub_notification_type type,
+dmub_notify_interrupt_callback_t callback, bool dmub_int_thread_offload)
+{
+	if (callback != NULL && type < ARRAY_SIZE(adev->dm.dmub_thread_offload)) {
+		adev->dm.dmub_callback[type] = callback;
+		adev->dm.dmub_thread_offload[type] = dmub_int_thread_offload;
+	} else
+		return false;
+
+	return true;
+}
+
+static void dm_handle_hpd_work(struct work_struct *work)
+{
+	struct dmub_hpd_work *dmub_hpd_wrk;
+
+	dmub_hpd_wrk = container_of(work, struct dmub_hpd_work, handle_hpd_work);
+
+	if (!dmub_hpd_wrk->dmub_notify) {
+		DRM_ERROR("dmub_hpd_wrk dmub_notify is NULL");
+		return;
+	}
+
+	if (dmub_hpd_wrk->dmub_notify->type < ARRAY_SIZE(dmub_hpd_wrk->adev->dm.dmub_callback)) {
+		dmub_hpd_wrk->adev->dm.dmub_callback[dmub_hpd_wrk->dmub_notify->type](dmub_hpd_wrk->adev,
+		dmub_hpd_wrk->dmub_notify);
+	}
+
+	kfree(dmub_hpd_wrk->dmub_notify);
+	kfree(dmub_hpd_wrk);
+
+}
+
 #define DMUB_TRACE_MAX_READ 64
 /**
  * dm_dmub_outbox1_low_irq() - Handles Outbox interrupt
@@ -634,22 +794,51 @@
 	struct amdgpu_display_manager *dm = &adev->dm;
 	struct dmcub_trace_buf_entry entry = { 0 };
 	uint32_t count = 0;
+	struct dmub_hpd_work *dmub_hpd_wrk;
+	struct dc_link *plink = NULL;
 
-	if (dc_enable_dmub_notifications(adev->dm.dc)) {
-		if (irq_params->irq_src == DC_IRQ_SOURCE_DMCUB_OUTBOX) {
-			do {
-				dc_stat_get_dmub_notification(adev->dm.dc, &notify);
-			} while (notify.pending_notification);
-
-			if (adev->dm.dmub_notify)
-				memcpy(adev->dm.dmub_notify, &notify, sizeof(struct dmub_notification));
-			if (notify.type == DMUB_NOTIFICATION_AUX_REPLY)
-				complete(&adev->dm.dmub_aux_transfer_done);
-			// TODO : HPD Implementation
+	if (dc_enable_dmub_notifications(adev->dm.dc) &&
+		irq_params->irq_src == DC_IRQ_SOURCE_DMCUB_OUTBOX) {
 
-		} else {
-			DRM_ERROR("DM: Failed to receive correct outbox IRQ !");
-		}
+		do {
+			dc_stat_get_dmub_notification(adev->dm.dc, &notify);
+			if (notify.type >= ARRAY_SIZE(dm->dmub_thread_offload)) {
+				DRM_ERROR("DM: notify type %d invalid!", notify.type);
+				continue;
+			}
+			if (!dm->dmub_callback[notify.type]) {
+				DRM_DEBUG_DRIVER("DMUB notification skipped, no handler: type=%d\n", notify.type);
+				continue;
+			}
+			if (dm->dmub_thread_offload[notify.type] == true) {
+				dmub_hpd_wrk = kzalloc(sizeof(*dmub_hpd_wrk), GFP_ATOMIC);
+				if (!dmub_hpd_wrk) {
+					DRM_ERROR("Failed to allocate dmub_hpd_wrk");
+					return;
+				}
+				dmub_hpd_wrk->dmub_notify = kzalloc(sizeof(struct dmub_notification), GFP_ATOMIC);
+				if (!dmub_hpd_wrk->dmub_notify) {
+					kfree(dmub_hpd_wrk);
+					DRM_ERROR("Failed to allocate dmub_hpd_wrk->dmub_notify");
+					return;
+				}
+				INIT_WORK(&dmub_hpd_wrk->handle_hpd_work, dm_handle_hpd_work);
+				if (dmub_hpd_wrk->dmub_notify)
+					memcpy(dmub_hpd_wrk->dmub_notify, &notify, sizeof(struct dmub_notification));
+				dmub_hpd_wrk->adev = adev;
+				if (notify.type == DMUB_NOTIFICATION_HPD) {
+					plink = adev->dm.dc->links[notify.link_index];
+					if (plink) {
+						plink->hpd_status =
+							notify.hpd_status ==
+							DP_HPD_PLUG ? true : false;
+					}
+				}
+				queue_work(adev->dm.delayed_hpd_wq, &dmub_hpd_wrk->handle_hpd_work);
+			} else {
+				dm->dmub_callback[notify.type](adev, &notify);
+			}
+		} while (notify.pending_notification);
 	}
 
 
@@ -667,7 +856,8 @@
 
 	} while (count <= DMUB_TRACE_MAX_READ);
 
-	ASSERT(count <= DMUB_TRACE_MAX_READ);
+	if (count > DMUB_TRACE_MAX_READ)
+		DRM_DEBUG_DRIVER("Warning : count > DMUB_TRACE_MAX_READ");
 }
 #endif
 
@@ -873,6 +1063,7 @@
 	const unsigned char *fw_inst_const, *fw_bss_data;
 	uint32_t i, fw_inst_const_size, fw_bss_data_size;
 	bool has_hw_support;
+	struct dc *dc = adev->dm.dc;
 
 	if (!dmub_srv)
 		/* DMUB isn't supported on the ASIC. */
@@ -900,6 +1091,11 @@
 		return 0;
 	}
 
+	/* Reset DMCUB if it was previously running - before we overwrite its memory. */
+	status = dmub_srv_hw_reset(dmub_srv);
+	if (status != DMUB_STATUS_OK)
+		DRM_WARN("Error resetting DMUB HW: %d\n", status);
+
 	hdr = (const struct dmcub_firmware_header_v1_0 *)dmub_fw->data;
 
 	fw_inst_const = dmub_fw->data +
@@ -959,6 +1155,19 @@
 	for (i = 0; i < fb_info->num_fb; ++i)
 		hw_params.fb[i] = &fb_info->fb[i];
 
+	switch (adev->asic_type) {
+	case CHIP_YELLOW_CARP:
+		if (dc->ctx->asic_id.hw_internal_rev != YELLOW_CARP_A0) {
+			hw_params.dpia_supported = true;
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+			hw_params.disable_dpia = dc->debug.dpia_debug.bits.disable_dpia;
+#endif
+		}
+		break;
+	default:
+		break;
+	}
+
 	status = dmub_srv_hw_init(dmub_srv, &hw_params);
 	if (status != DMUB_STATUS_OK) {
 		DRM_ERROR("Error initializing DMUB HW: %d\n", status);
@@ -989,6 +1198,32 @@
 	return 0;
 }
 
+static void dm_dmub_hw_resume(struct amdgpu_device *adev)
+{
+	struct dmub_srv *dmub_srv = adev->dm.dmub_srv;
+	enum dmub_status status;
+	bool init;
+
+	if (!dmub_srv) {
+		/* DMUB isn't supported on the ASIC. */
+		return;
+	}
+
+	status = dmub_srv_is_hw_init(dmub_srv, &init);
+	if (status != DMUB_STATUS_OK)
+		DRM_WARN("DMUB hardware init check failed: %d\n", status);
+
+	if (status == DMUB_STATUS_OK && init) {
+		/* Wait for firmware load to finish. */
+		status = dmub_srv_wait_for_auto_load(dmub_srv, 100000);
+		if (status != DMUB_STATUS_OK)
+			DRM_WARN("Wait for DMUB auto-load failed: %d\n", status);
+	} else {
+		/* Perform the full hardware initialization. */
+		dm_dmub_hw_init(adev);
+	}
+}
+
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 static void mmhub_read_system_context(struct amdgpu_device *adev, struct dc_phy_addr_space_config *pa_config)
 {
@@ -1019,11 +1254,15 @@
 	agp_top = adev->gmc.agp_end >> 24;
 
 
-	page_table_start.high_part = (u32)(adev->gmc.gart_start >> 44) & 0xF;
-	page_table_start.low_part = (u32)(adev->gmc.gart_start >> 12);
-	page_table_end.high_part = (u32)(adev->gmc.gart_end >> 44) & 0xF;
-	page_table_end.low_part = (u32)(adev->gmc.gart_end >> 12);
-	page_table_base.high_part = upper_32_bits(pt_base) & 0xF;
+	page_table_start.high_part = upper_32_bits(adev->gmc.gart_start >>
+						   AMDGPU_GPU_PAGE_SHIFT);
+	page_table_start.low_part = lower_32_bits(adev->gmc.gart_start >>
+						  AMDGPU_GPU_PAGE_SHIFT);
+	page_table_end.high_part = upper_32_bits(adev->gmc.gart_end >>
+						 AMDGPU_GPU_PAGE_SHIFT);
+	page_table_end.low_part = lower_32_bits(adev->gmc.gart_end >>
+						AMDGPU_GPU_PAGE_SHIFT);
+	page_table_base.high_part = upper_32_bits(pt_base);
 	page_table_base.low_part = lower_32_bits(pt_base);
 
 	pa_config->system_aperture.start_addr = (uint64_t)logical_addr_low << 18;
@@ -1083,6 +1322,194 @@
 }
 
 #endif
+
+static void dm_handle_hpd_rx_offload_work(struct work_struct *work)
+{
+	struct hpd_rx_irq_offload_work *offload_work;
+	struct amdgpu_dm_connector *aconnector;
+	struct dc_link *dc_link;
+	struct amdgpu_device *adev;
+	enum dc_connection_type new_connection_type = dc_connection_none;
+	unsigned long flags;
+
+	offload_work = container_of(work, struct hpd_rx_irq_offload_work, work);
+	aconnector = offload_work->offload_wq->aconnector;
+
+	if (!aconnector) {
+		DRM_ERROR("Can't retrieve aconnector in hpd_rx_irq_offload_work");
+		goto skip;
+	}
+
+	adev = drm_to_adev(aconnector->base.dev);
+	dc_link = aconnector->dc_link;
+
+	mutex_lock(&aconnector->hpd_lock);
+	if (!dc_link_detect_sink(dc_link, &new_connection_type))
+		DRM_ERROR("KMS: Failed to detect connector\n");
+	mutex_unlock(&aconnector->hpd_lock);
+
+	if (new_connection_type == dc_connection_none)
+		goto skip;
+
+	if (amdgpu_in_reset(adev))
+		goto skip;
+
+	mutex_lock(&adev->dm.dc_lock);
+	if (offload_work->data.bytes.device_service_irq.bits.AUTOMATED_TEST)
+		dc_link_dp_handle_automated_test(dc_link);
+	else if ((dc_link->connector_signal != SIGNAL_TYPE_EDP) &&
+			hpd_rx_irq_check_link_loss_status(dc_link, &offload_work->data) &&
+			dc_link_dp_allow_hpd_rx_irq(dc_link)) {
+		dc_link_dp_handle_link_loss(dc_link);
+		spin_lock_irqsave(&offload_work->offload_wq->offload_lock, flags);
+		offload_work->offload_wq->is_handling_link_loss = false;
+		spin_unlock_irqrestore(&offload_work->offload_wq->offload_lock, flags);
+	}
+	mutex_unlock(&adev->dm.dc_lock);
+
+skip:
+	kfree(offload_work);
+
+}
+
+static struct hpd_rx_irq_offload_work_queue *hpd_rx_irq_create_workqueue(struct dc *dc)
+{
+	int max_caps = dc->caps.max_links;
+	int i = 0;
+	struct hpd_rx_irq_offload_work_queue *hpd_rx_offload_wq = NULL;
+
+	hpd_rx_offload_wq = kcalloc(max_caps, sizeof(*hpd_rx_offload_wq), GFP_KERNEL);
+
+	if (!hpd_rx_offload_wq)
+		return NULL;
+
+
+	for (i = 0; i < max_caps; i++) {
+		hpd_rx_offload_wq[i].wq =
+				    create_singlethread_workqueue("amdgpu_dm_hpd_rx_offload_wq");
+
+		if (hpd_rx_offload_wq[i].wq == NULL) {
+			DRM_ERROR("create amdgpu_dm_hpd_rx_offload_wq fail!");
+			goto out_err;
+		}
+
+		spin_lock_init(&hpd_rx_offload_wq[i].offload_lock);
+	}
+
+	return hpd_rx_offload_wq;
+
+out_err:
+	for (i = 0; i < max_caps; i++) {
+		if (hpd_rx_offload_wq[i].wq)
+			destroy_workqueue(hpd_rx_offload_wq[i].wq);
+	}
+	kfree(hpd_rx_offload_wq);
+	return NULL;
+}
+
+struct amdgpu_stutter_quirk {
+	u16 chip_vendor;
+	u16 chip_device;
+	u16 subsys_vendor;
+	u16 subsys_device;
+	u8 revision;
+};
+
+static const struct amdgpu_stutter_quirk amdgpu_stutter_quirk_list[] = {
+	/* https://bugzilla.kernel.org/show_bug.cgi?id=214417 */
+	{ 0x1002, 0x15dd, 0x1002, 0x15dd, 0xc8 },
+	{ 0, 0, 0, 0, 0 },
+};
+
+static bool dm_should_disable_stutter(struct pci_dev *pdev)
+{
+	const struct amdgpu_stutter_quirk *p = amdgpu_stutter_quirk_list;
+
+	while (p && p->chip_device != 0) {
+		if (pdev->vendor == p->chip_vendor &&
+		    pdev->device == p->chip_device &&
+		    pdev->subsystem_vendor == p->subsys_vendor &&
+		    pdev->subsystem_device == p->subsys_device &&
+		    pdev->revision == p->revision) {
+			return true;
+		}
+		++p;
+	}
+	return false;
+}
+
+static const struct dmi_system_id hpd_disconnect_quirk_table[] = {
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Precision 3660"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Precision 3260"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Precision 3460"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex Tower Plus 7010"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex Tower 7010"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex SFF Plus 7010"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex SFF 7010"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex Micro Plus 7010"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex Micro 7010"),
+		},
+	},
+	{}
+	/* TODO: refactor this from a fixed table to a dynamic option */
+};
+
+static void retrieve_dmi_info(struct amdgpu_display_manager *dm)
+{
+	const struct dmi_system_id *dmi_id;
+
+	dm->aux_hpd_discon_quirk = false;
+
+	dmi_id = dmi_first_match(hpd_disconnect_quirk_table);
+	if (dmi_id) {
+		dm->aux_hpd_discon_quirk = true;
+		DRM_INFO("aux_hpd_discon_quirk attached\n");
+	}
+}
+
 static int amdgpu_dm_init(struct amdgpu_device *adev)
 {
 	struct dc_init_data init_data;
@@ -1141,8 +1568,15 @@
 	case CHIP_RAVEN:
 	case CHIP_RENOIR:
 		init_data.flags.gpu_vm_support = true;
-		if (ASICREV_IS_GREEN_SARDINE(adev->external_rev_id))
+		switch (adev->dm.dmcub_fw_version) {
+		case 0: /* development */
+		case 0x1: /* linux-firmware.git hash 6d9f399 */
+		case 0x01000000: /* linux-firmware.git hash 9a0b0f4 */
+			init_data.flags.disable_dmcu = false;
+			break;
+		default:
 			init_data.flags.disable_dmcu = true;
+		}
 		break;
 	case CHIP_VANGOGH:
 	case CHIP_YELLOW_CARP:
@@ -1167,6 +1601,9 @@
 	init_data.flags.power_down_display_on_boot = true;
 
 	INIT_LIST_HEAD(&adev->dm.da_list);
+
+	retrieve_dmi_info(&adev->dm);
+
 	/* Display Core create. */
 	adev->dm.dc = dc_create(&init_data);
 
@@ -1184,6 +1621,8 @@
 
 	if (adev->asic_type != CHIP_CARRIZO && adev->asic_type != CHIP_STONEY)
 		adev->dm.dc->debug.disable_stutter = amdgpu_pp_feature_mask & PP_STUTTER_MODE ? false : true;
+	if (dm_should_disable_stutter(adev->pdev))
+		adev->dm.dc->debug.disable_stutter = true;
 
 	if (amdgpu_dc_debug_mask & DC_DISABLE_STUTTER)
 		adev->dm.dc->debug.disable_stutter = true;
@@ -1202,6 +1641,12 @@
 
 	dc_hardware_init(adev->dm.dc);
 
+	adev->dm.hpd_rx_offload_wq = hpd_rx_irq_create_workqueue(adev->dm.dc);
+	if (!adev->dm.hpd_rx_offload_wq) {
+		DRM_ERROR("amdgpu: failed to create hpd rx offload workqueue.\n");
+		goto error;
+	}
+
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 	if ((adev->flags & AMD_IS_APU) && (adev->asic_type >= CHIP_CARRIZO)) {
 		struct dc_phy_addr_space_config pa_config;
@@ -1247,14 +1692,36 @@
 #if defined(CONFIG_DRM_AMD_SECURE_DISPLAY)
 	adev->dm.crc_rd_wrk = amdgpu_dm_crtc_secure_display_create_work();
 #endif
-	if (dc_enable_dmub_notifications(adev->dm.dc)) {
+	if (dc_is_dmub_outbox_supported(adev->dm.dc)) {
 		init_completion(&adev->dm.dmub_aux_transfer_done);
 		adev->dm.dmub_notify = kzalloc(sizeof(struct dmub_notification), GFP_KERNEL);
 		if (!adev->dm.dmub_notify) {
 			DRM_INFO("amdgpu: fail to allocate adev->dm.dmub_notify");
 			goto error;
 		}
+
+		adev->dm.delayed_hpd_wq = create_singlethread_workqueue("amdgpu_dm_hpd_wq");
+		if (!adev->dm.delayed_hpd_wq) {
+			DRM_ERROR("amdgpu: failed to create hpd offload workqueue.\n");
+			goto error;
+		}
+
 		amdgpu_dm_outbox_init(adev);
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+		if (!register_dmub_notify_callback(adev, DMUB_NOTIFICATION_AUX_REPLY,
+			dmub_aux_setconfig_callback, false)) {
+			DRM_ERROR("amdgpu: fail to register dmub aux callback");
+			goto error;
+		}
+		if (!register_dmub_notify_callback(adev, DMUB_NOTIFICATION_HPD, dmub_hpd_callback, true)) {
+			DRM_ERROR("amdgpu: fail to register dmub hpd callback");
+			goto error;
+		}
+		if (!register_dmub_notify_callback(adev, DMUB_NOTIFICATION_HPD_IRQ, dmub_hpd_callback, true)) {
+			DRM_ERROR("amdgpu: fail to register dmub hpd callback");
+			goto error;
+		}
+#endif
 	}
 
 	if (amdgpu_dm_initialize_drm_device(adev)) {
@@ -1263,6 +1730,13 @@
 		goto error;
 	}
 
+	/* Enable outbox notification only after IRQ handlers are registered and DMUB is alive.
+	 * It is expected that DMUB will resend any pending notifications at this point, for
+	 * example HPD from DPIA.
+	 */
+	if (dc_is_dmub_outbox_supported(adev->dm.dc))
+		dc_enable_dmub_outbox(adev->dm.dc);
+
 	/* create fake encoders for MST */
 	dm_dp_create_fake_mst_encoders(adev);
 
@@ -1308,10 +1782,6 @@
 	}
 #endif
 
-	for (i = 0; i < adev->dm.display_indexes_num; i++) {
-		drm_encoder_cleanup(&adev->dm.mst_encoders[i].base);
-	}
-
 	amdgpu_dm_destroy_drm_device(&adev->dm);
 
 #if defined(CONFIG_DRM_AMD_SECURE_DISPLAY)
@@ -1331,11 +1801,14 @@
 		dc_deinit_callbacks(adev->dm.dc);
 #endif
 
-	dc_dmub_srv_destroy(&adev->dm.dc->ctx->dmub_srv);
+	if (adev->dm.dc)
+		dc_dmub_srv_destroy(&adev->dm.dc->ctx->dmub_srv);
 
 	if (dc_enable_dmub_notifications(adev->dm.dc)) {
 		kfree(adev->dm.dmub_notify);
 		adev->dm.dmub_notify = NULL;
+		destroy_workqueue(adev->dm.delayed_hpd_wq);
+		adev->dm.delayed_hpd_wq = NULL;
 	}
 
 	if (adev->dm.dmub_bo)
@@ -1361,6 +1834,18 @@
 		adev->dm.freesync_module = NULL;
 	}
 
+	if (adev->dm.hpd_rx_offload_wq) {
+		for (i = 0; i < adev->dm.dc->caps.max_links; i++) {
+			if (adev->dm.hpd_rx_offload_wq[i].wq) {
+				destroy_workqueue(adev->dm.hpd_rx_offload_wq[i].wq);
+				adev->dm.hpd_rx_offload_wq[i].wq = NULL;
+			}
+		}
+
+		kfree(adev->dm.hpd_rx_offload_wq);
+		adev->dm.hpd_rx_offload_wq = NULL;
+	}
+
 	mutex_destroy(&adev->dm.audio_lock);
 	mutex_destroy(&adev->dm.dc_lock);
 
@@ -1487,7 +1972,7 @@
 	struct dmub_srv_create_params create_params;
 	struct dmub_srv_region_params region_params;
 	struct dmub_srv_region_info region_info;
-	struct dmub_srv_fb_params fb_params;
+	struct dmub_srv_memory_params memory_params;
 	struct dmub_srv_fb_info *fb_info;
 	struct dmub_srv *dmub_srv;
 	const struct dmcub_firmware_header_v1_0 *hdr;
@@ -1524,7 +2009,7 @@
 		fw_name_dmub = FIRMWARE_BEIGE_GOBY_DMUB;
 		break;
 	case CHIP_YELLOW_CARP:
-		dmub_asic = DMUB_ASIC_DCN31;
+		dmub_asic = (adev->external_rev_id == YELLOW_CARP_B0) ? DMUB_ASIC_DCN31B : DMUB_ASIC_DCN31;
 		fw_name_dmub = FIRMWARE_YELLOW_CARP_DMUB;
 		break;
 
@@ -1597,6 +2082,7 @@
 		adev->dm.dmub_fw->data +
 		le32_to_cpu(hdr->header.ucode_array_offset_bytes) +
 		PSP_HEADER_BYTES;
+	region_params.is_mailbox_in_inbox = false;
 
 	status = dmub_srv_calc_region_info(dmub_srv, &region_params,
 					   &region_info);
@@ -1618,10 +2104,10 @@
 		return r;
 
 	/* Rebase the regions on the framebuffer address. */
-	memset(&fb_params, 0, sizeof(fb_params));
-	fb_params.cpu_addr = adev->dm.dmub_bo_cpu_addr;
-	fb_params.gpu_addr = adev->dm.dmub_bo_gpu_addr;
-	fb_params.region_info = &region_info;
+	memset(&memory_params, 0, sizeof(memory_params));
+	memory_params.cpu_fb_addr = adev->dm.dmub_bo_cpu_addr;
+	memory_params.gpu_fb_addr = adev->dm.dmub_bo_gpu_addr;
+	memory_params.region_info = &region_info;
 
 	adev->dm.dmub_fb_info =
 		kzalloc(sizeof(*adev->dm.dmub_fb_info), GFP_KERNEL);
@@ -1633,7 +2119,7 @@
 		return -ENOMEM;
 	}
 
-	status = dmub_srv_calc_fb_info(dmub_srv, &fb_params, fb_info);
+	status = dmub_srv_calc_mem_info(dmub_srv, &memory_params, fb_info);
 	if (status != DMUB_STATUS_OK) {
 		DRM_ERROR("Error calculating DMUB FB info: %d\n", status);
 		return -EINVAL;
@@ -1663,6 +2149,7 @@
 
 	if (adev->dm.dmub_srv) {
 		dmub_srv_destroy(adev->dm.dmub_srv);
+		kfree(adev->dm.dmub_srv);
 		adev->dm.dmub_srv = NULL;
 	}
 
@@ -1774,7 +2261,8 @@
 		} else {
 			ret = drm_dp_mst_topology_mgr_resume(mgr, true);
 			if (ret < 0) {
-				drm_dp_mst_topology_mgr_set_mst(mgr, false);
+				dm_helpers_dp_mst_stop_top_mgr(aconnector->dc_link->ctx,
+					aconnector->dc_link);
 				need_hotplug = true;
 			}
 		}
@@ -1980,6 +2468,16 @@
 	return res;
 }
 
+static void hpd_rx_irq_work_suspend(struct amdgpu_display_manager *dm)
+{
+	int i;
+
+	if (dm->hpd_rx_offload_wq) {
+		for (i = 0; i < dm->dc->caps.max_links; i++)
+			flush_workqueue(dm->hpd_rx_offload_wq[i].wq);
+	}
+}
+
 static int dm_suspend(void *handle)
 {
 	struct amdgpu_device *adev = handle;
@@ -1995,12 +2493,15 @@
 
 		dm->cached_dc_state = dc_copy_state(dm->dc->current_state);
 
-		dm_gpureset_toggle_interrupts(adev, dm->cached_dc_state, false);
+		if (dm->cached_dc_state)
+			dm_gpureset_toggle_interrupts(adev, dm->cached_dc_state, false);
 
 		amdgpu_dm_commit_zero_streams(dm->dc);
 
 		amdgpu_dm_irq_suspend(adev);
 
+		hpd_rx_irq_work_suspend(dm);
+
 		return ret;
 	}
 
@@ -2011,6 +2512,8 @@
 
 	amdgpu_dm_irq_suspend(adev);
 
+	hpd_rx_irq_work_suspend(dm);
+
 	dc_set_power_state(dm->dc, DC_ACPI_CM_POWER_STATE_D3);
 
 	return 0;
@@ -2145,10 +2648,13 @@
 			bundle->surface_updates[m].surface->force_full_update =
 				true;
 		}
-		dc_commit_updates_for_stream(
-			dm->dc, bundle->surface_updates,
-			dc_state->stream_status->plane_count,
-			dc_state->streams[k], &bundle->stream_update, dc_state);
+
+		update_planes_and_stream_adapter(dm->dc,
+					 UPDATE_TYPE_FULL,
+					 dc_state->stream_status->plane_count,
+					 dc_state->streams[k],
+					 &bundle->stream_update,
+					 bundle->surface_updates);
 	}
 
 cleanup:
@@ -2206,6 +2712,20 @@
 	if (amdgpu_in_reset(adev)) {
 		dc_state = dm->cached_dc_state;
 
+		/*
+		 * The dc->current_state is backed up into dm->cached_dc_state
+		 * before we commit 0 streams.
+		 *
+		 * DC will clear link encoder assignments on the real state
+		 * but the changes won't propagate over to the copy we made
+		 * before the 0 streams commit.
+		 *
+		 * DC expects that link encoder assignments are *not* valid
+		 * when committing a state, so as a workaround it needs to be
+		 * cleared here.
+		 */
+		link_enc_cfg_init(dm->dc, dc_state);
+
 		r = dm_dmub_hw_init(adev);
 		if (r)
 			DRM_ERROR("DMUB interface failed to initialize: status=%d\n", r);
@@ -2217,8 +2737,8 @@
 
 		for (i = 0; i < dc_state->stream_count; i++) {
 			dc_state->streams[i]->mode_changed = true;
-			for (j = 0; j < dc_state->stream_status->plane_count; j++) {
-				dc_state->stream_status->plane_states[j]->update_flags.raw
+			for (j = 0; j < dc_state->stream_status[i].plane_count; j++) {
+				dc_state->stream_status[i].plane_states[j]->update_flags.raw
 					= 0xffffffff;
 			}
 		}
@@ -2232,6 +2752,11 @@
 		WARN_ON(dc_validate_global_state(dm->dc, dc_state, false) != DC_OK);
 #endif
 
+		if (dc_is_dmub_outbox_supported(adev->dm.dc)) {
+			amdgpu_dm_outbox_init(adev);
+			dc_enable_dmub_outbox(adev->dm.dc);
+		}
+
 		WARN_ON(!dc_commit_state(dm->dc, dc_state));
 
 		dm_gpureset_commit_state(dm->cached_dc_state, dm);
@@ -2245,8 +2770,19 @@
 
 		mutex_unlock(&dm->dc_lock);
 
+		/* set the backlight after a reset */
+		for (i = 0; i < dm->num_of_edps; i++) {
+			if (dm->backlight_dev[i])
+				amdgpu_dm_backlight_set_level(dm, i, dm->brightness[i]);
+		}
+
 		return 0;
 	}
+
+	/* leave display off for S4 sequence */
+	if (adev->in_s4)
+		return 0;
+
 	/* Recreate dc_state - DC invalidates it when setting power state to S3. */
 	dc_release_state(dm_state->context);
 	dm_state->context = dc_create_state(dm->dc);
@@ -2254,9 +2790,13 @@
 	dc_resource_state_construct(dm->dc, dm_state->context);
 
 	/* Before powering on DC we need to re-initialize DMUB. */
-	r = dm_dmub_hw_init(adev);
-	if (r)
-		DRM_ERROR("DMUB interface failed to initialize: status=%d\n", r);
+	dm_dmub_hw_resume(adev);
+
+	/* Re-enable outbox interrupts for DPIA. */
+	if (dc_is_dmub_outbox_supported(adev->dm.dc)) {
+		amdgpu_dm_outbox_init(adev);
+		dc_enable_dmub_outbox(adev->dm.dc);
+	}
 
 	/* power on hardware */
 	dc_set_power_state(dm->dc, DC_ACPI_CM_POWER_STATE_D0);
@@ -2278,11 +2818,14 @@
 	drm_for_each_connector_iter(connector, &iter) {
 		aconnector = to_amdgpu_dm_connector(connector);
 
+		if (!aconnector->dc_link)
+			continue;
+
 		/*
 		 * this is the case when traversing through already created
 		 * MST connectors, should be skipped
 		 */
-		if (aconnector->mst_port)
+		if (aconnector->dc_link->type == dc_connection_mst_branch)
 			continue;
 
 		mutex_lock(&aconnector->hpd_lock);
@@ -2321,6 +2864,7 @@
 			dc_stream_release(dm_new_crtc_state->stream);
 			dm_new_crtc_state->stream = NULL;
 		}
+		dm_new_crtc_state->base.color_mgmt_changed = true;
 	}
 
 	for_each_new_plane_in_state(dm->cached_state, plane, new_plane_state, i) {
@@ -2402,15 +2946,12 @@
 
 static void update_connector_ext_caps(struct amdgpu_dm_connector *aconnector)
 {
-	u32 max_cll, min_cll, max, min, q, r;
 	struct amdgpu_dm_backlight_caps *caps;
 	struct amdgpu_display_manager *dm;
 	struct drm_connector *conn_base;
 	struct amdgpu_device *adev;
 	struct dc_link *link = NULL;
-	static const u8 pre_computed_values[] = {
-		50, 51, 52, 53, 55, 56, 57, 58, 59, 61, 62, 63, 65, 66, 68, 69,
-		71, 72, 74, 75, 77, 79, 81, 82, 84, 86, 88, 90, 92, 94, 96, 98};
+	struct drm_luminance_range_info *luminance_range;
 	int i;
 
 	if (!aconnector || !aconnector->dc_link)
@@ -2432,8 +2973,6 @@
 	caps = &dm->backlight_caps[i];
 	caps->ext_caps = &aconnector->dc_link->dpcd_sink_ext_caps;
 	caps->aux_support = false;
-	max_cll = conn_base->hdr_sink_metadata.hdmi_type1.max_cll;
-	min_cll = conn_base->hdr_sink_metadata.hdmi_type1.min_cll;
 
 	if (caps->ext_caps->bits.oled == 1 /*||
 	    caps->ext_caps->bits.sdr_aux_backlight_control == 1 ||
@@ -2445,31 +2984,9 @@
 	else if (amdgpu_backlight == 1)
 		caps->aux_support = true;
 
-	/* From the specification (CTA-861-G), for calculating the maximum
-	 * luminance we need to use:
-	 *	Luminance = 50*2**(CV/32)
-	 * Where CV is a one-byte value.
-	 * For calculating this expression we may need float point precision;
-	 * to avoid this complexity level, we take advantage that CV is divided
-	 * by a constant. From the Euclids division algorithm, we know that CV
-	 * can be written as: CV = 32*q + r. Next, we replace CV in the
-	 * Luminance expression and get 50*(2**q)*(2**(r/32)), hence we just
-	 * need to pre-compute the value of r/32. For pre-computing the values
-	 * We just used the following Ruby line:
-	 *	(0...32).each {|cv| puts (50*2**(cv/32.0)).round}
-	 * The results of the above expressions can be verified at
-	 * pre_computed_values.
-	 */
-	q = max_cll >> 5;
-	r = max_cll % 32;
-	max = (1 << q) * pre_computed_values[r];
-
-	// min luminance: maxLum * (CV/255)^2 / 100
-	q = DIV_ROUND_CLOSEST(min_cll, 255);
-	min = max * DIV_ROUND_CLOSEST((q * q), 100);
-
-	caps->aux_max_input_signal = max;
-	caps->aux_min_input_signal = min;
+	luminance_range = &conn_base->display_info.luminance_range;
+	caps->aux_min_input_signal = luminance_range->min_luminance;
+	caps->aux_max_input_signal = luminance_range->max_luminance;
 }
 
 void amdgpu_dm_update_connector_after_detect(
@@ -2583,13 +3100,12 @@
 			aconnector->edid =
 				(struct edid *)sink->dc_edid.raw_edid;
 
-			drm_connector_update_edid_property(connector,
-							   aconnector->edid);
 			if (aconnector->dc_link->aux_mode)
 				drm_dp_cec_set_edid(&aconnector->dm_dp_aux.aux,
 						    aconnector->edid);
 		}
 
+		drm_connector_update_edid_property(connector, aconnector->edid);
 		amdgpu_dm_update_freesync_caps(connector, aconnector->edid);
 		update_connector_ext_caps(aconnector);
 	} else {
@@ -2615,9 +3131,8 @@
 		dc_sink_release(sink);
 }
 
-static void handle_hpd_irq(void *param)
+static void handle_hpd_irq_helper(struct amdgpu_dm_connector *aconnector)
 {
-	struct amdgpu_dm_connector *aconnector = (struct amdgpu_dm_connector *)param;
 	struct drm_connector *connector = &aconnector->base;
 	struct drm_device *dev = connector->dev;
 	enum dc_connection_type new_connection_type = dc_connection_none;
@@ -2650,7 +3165,6 @@
 	if (aconnector->base.force && new_connection_type == dc_connection_none) {
 		emulated_link_detect(aconnector->dc_link);
 
-
 		drm_modeset_lock_all(dev);
 		dm_restore_drm_connector_state(dev, connector);
 		drm_modeset_unlock_all(dev);
@@ -2676,7 +3190,15 @@
 
 }
 
-static void dm_handle_hpd_rx_irq(struct amdgpu_dm_connector *aconnector)
+static void handle_hpd_irq(void *param)
+{
+	struct amdgpu_dm_connector *aconnector = (struct amdgpu_dm_connector *)param;
+
+	handle_hpd_irq_helper(aconnector);
+
+}
+
+static void dm_handle_mst_sideband_msg(struct amdgpu_dm_connector *aconnector)
 {
 	uint8_t esi[DP_PSR_ERROR_STATUS - DP_SINK_COUNT_ESI] = { 0 };
 	uint8_t dret;
@@ -2754,6 +3276,25 @@
 		DRM_DEBUG_DRIVER("Loop exceeded max iterations\n");
 }
 
+static void schedule_hpd_rx_offload_work(struct hpd_rx_irq_offload_work_queue *offload_wq,
+							union hpd_irq_data hpd_irq_data)
+{
+	struct hpd_rx_irq_offload_work *offload_work =
+				kzalloc(sizeof(*offload_work), GFP_KERNEL);
+
+	if (!offload_work) {
+		DRM_ERROR("Failed to allocate hpd_rx_irq_offload_work.\n");
+		return;
+	}
+
+	INIT_WORK(&offload_work->work, dm_handle_hpd_rx_offload_work);
+	offload_work->data = hpd_irq_data;
+	offload_work->offload_wq = offload_wq;
+
+	queue_work(offload_wq->wq, &offload_work->work);
+	DRM_DEBUG_KMS("queue work to handle hpd_rx offload work");
+}
+
 static void handle_hpd_rx_irq(void *param)
 {
 	struct amdgpu_dm_connector *aconnector = (struct amdgpu_dm_connector *)param;
@@ -2765,14 +3306,16 @@
 	enum dc_connection_type new_connection_type = dc_connection_none;
 	struct amdgpu_device *adev = drm_to_adev(dev);
 	union hpd_irq_data hpd_irq_data;
-	bool lock_flag = 0;
+	bool link_loss = false;
+	bool has_left_work = false;
+	int idx = aconnector->base.index;
+	struct hpd_rx_irq_offload_work_queue *offload_wq = &adev->dm.hpd_rx_offload_wq[idx];
 
 	memset(&hpd_irq_data, 0, sizeof(hpd_irq_data));
 
 	if (adev->dm.disable_hpd_irq)
 		return;
 
-
 	/*
 	 * TODO:Temporary add mutex to protect hpd interrupt not have a gpio
 	 * conflict, after implement i2c helper, this mutex should be
@@ -2780,43 +3323,41 @@
 	 */
 	mutex_lock(&aconnector->hpd_lock);
 
-	read_hpd_rx_irq_data(dc_link, &hpd_irq_data);
+	result = dc_link_handle_hpd_rx_irq(dc_link, &hpd_irq_data,
+						&link_loss, true, &has_left_work);
 
-	if ((dc_link->cur_link_settings.lane_count != LANE_COUNT_UNKNOWN) ||
-		(dc_link->type == dc_connection_mst_branch)) {
-		if (hpd_irq_data.bytes.device_service_irq.bits.UP_REQ_MSG_RDY) {
-			result = true;
-			dm_handle_hpd_rx_irq(aconnector);
-			goto out;
-		} else if (hpd_irq_data.bytes.device_service_irq.bits.DOWN_REP_MSG_RDY) {
-			result = false;
-			dm_handle_hpd_rx_irq(aconnector);
+	if (!has_left_work)
+		goto out;
+
+	if (hpd_irq_data.bytes.device_service_irq.bits.AUTOMATED_TEST) {
+		schedule_hpd_rx_offload_work(offload_wq, hpd_irq_data);
+		goto out;
+	}
+
+	if (dc_link_dp_allow_hpd_rx_irq(dc_link)) {
+		if (hpd_irq_data.bytes.device_service_irq.bits.UP_REQ_MSG_RDY ||
+			hpd_irq_data.bytes.device_service_irq.bits.DOWN_REP_MSG_RDY) {
+			dm_handle_mst_sideband_msg(aconnector);
 			goto out;
 		}
-	}
 
-	/*
-	 * TODO: We need the lock to avoid touching DC state while it's being
-	 * modified during automated compliance testing, or when link loss
-	 * happens. While this should be split into subhandlers and proper
-	 * interfaces to avoid having to conditionally lock like this in the
-	 * outer layer, we need this workaround temporarily to allow MST
-	 * lightup in some scenarios to avoid timeout.
-	 */
-	if (!amdgpu_in_reset(adev) &&
-	    (hpd_rx_irq_check_link_loss_status(dc_link, &hpd_irq_data) ||
-	     hpd_irq_data.bytes.device_service_irq.bits.AUTOMATED_TEST)) {
-		mutex_lock(&adev->dm.dc_lock);
-		lock_flag = 1;
-	}
+		if (link_loss) {
+			bool skip = false;
 
-#ifdef CONFIG_DRM_AMD_DC_HDCP
-	result = dc_link_handle_hpd_rx_irq(dc_link, &hpd_irq_data, NULL);
-#else
-	result = dc_link_handle_hpd_rx_irq(dc_link, NULL, NULL);
-#endif
-	if (!amdgpu_in_reset(adev) && lock_flag)
-		mutex_unlock(&adev->dm.dc_lock);
+			spin_lock(&offload_wq->offload_lock);
+			skip = offload_wq->is_handling_link_loss;
+
+			if (!skip)
+				offload_wq->is_handling_link_loss = true;
+
+			spin_unlock(&offload_wq->offload_lock);
+
+			if (!skip)
+				schedule_hpd_rx_offload_work(offload_wq, hpd_irq_data);
+
+			goto out;
+		}
+	}
 
 out:
 	if (result && !is_mst_root_connector) {
@@ -2901,6 +3442,10 @@
 			amdgpu_dm_irq_register_interrupt(adev, &int_params,
 					handle_hpd_rx_irq,
 					(void *) aconnector);
+
+			if (adev->dm.hpd_rx_offload_wq)
+				adev->dm.hpd_rx_offload_wq[connector->index].aconnector =
+					aconnector;
 		}
 	}
 }
@@ -3213,7 +3758,7 @@
 
 	/* Use GRPH_PFLIP interrupt */
 	for (i = DCN_1_0__SRCID__HUBP0_FLIP_INTERRUPT;
-			i <= DCN_1_0__SRCID__HUBP0_FLIP_INTERRUPT + adev->mode_info.num_crtc - 1;
+			i <= DCN_1_0__SRCID__HUBP0_FLIP_INTERRUPT + dc->caps.max_otg_num - 1;
 			i++) {
 		r = amdgpu_irq_add_id(adev, SOC15_IH_CLIENTID_DCE, i, &adev->pageflip_irq);
 		if (r) {
@@ -3424,6 +3969,7 @@
 
 #define AMDGPU_DM_DEFAULT_MIN_BACKLIGHT 12
 #define AMDGPU_DM_DEFAULT_MAX_BACKLIGHT 255
+#define AMDGPU_DM_MIN_SPREAD ((AMDGPU_DM_DEFAULT_MAX_BACKLIGHT - AMDGPU_DM_DEFAULT_MIN_BACKLIGHT) / 2)
 #define AUX_BL_DEFAULT_TRANSITION_TIME_MS 50
 
 #if defined(CONFIG_BACKLIGHT_CLASS_DEVICE) ||\
@@ -3441,6 +3987,21 @@
 		return;
 
 	amdgpu_acpi_get_backlight_caps(&caps);
+
+	/* validate the firmware value is sane */
+	if (caps.caps_valid) {
+		int spread = caps.max_input_signal - caps.min_input_signal;
+
+		if (caps.max_input_signal > AMDGPU_DM_DEFAULT_MAX_BACKLIGHT ||
+		    caps.min_input_signal < 0 ||
+		    spread > AMDGPU_DM_DEFAULT_MAX_BACKLIGHT ||
+		    spread < AMDGPU_DM_MIN_SPREAD) {
+			DRM_DEBUG_KMS("DM: Invalid backlight caps: min=%d, max=%d\n",
+				      caps.min_input_signal, caps.max_input_signal);
+			caps.caps_valid = false;
+		}
+	}
+
 	if (caps.caps_valid) {
 		dm->backlight_caps[bl_idx].caps_valid = true;
 		if (caps.aux_support)
@@ -3508,7 +4069,7 @@
 				 max - min);
 }
 
-static int amdgpu_dm_backlight_set_level(struct amdgpu_display_manager *dm,
+static void amdgpu_dm_backlight_set_level(struct amdgpu_display_manager *dm,
 					 int bl_idx,
 					 u32 user_brightness)
 {
@@ -3536,7 +4097,8 @@
 			DRM_DEBUG("DM: Failed to update backlight on eDP[%d]\n", bl_idx);
 	}
 
-	return rc ? 0 : 1;
+	if (rc)
+		dm->actual_brightness[bl_idx] = user_brightness;
 }
 
 static int amdgpu_dm_backlight_update_status(struct backlight_device *bd)
@@ -3715,6 +4277,7 @@
 	int32_t primary_planes;
 	enum dc_connection_type new_connection_type = dc_connection_none;
 	const struct dc_plane_cap *plane;
+	bool psr_feature_enabled = false;
 
 	dm->display_indexes_num = dm->dc->caps.max_streams;
 	/* Update the actual used number of crtc */
@@ -3728,7 +4291,10 @@
 
 	/* There is one primary plane per CRTC */
 	primary_planes = dm->dc->caps.max_streams;
-	ASSERT(primary_planes <= AMDGPU_MAX_PLANES);
+	if (primary_planes > AMDGPU_MAX_PLANES) {
+		DRM_ERROR("DM: Plane nums out of 6 planes\n");
+		return -EINVAL;
+	}
 
 	/*
 	 * Initialize primary planes, implicit planes for legacy IOCTLS.
@@ -3796,6 +4362,19 @@
 	default:
 		DRM_DEBUG_KMS("Unsupported ASIC type for outbox: 0x%X\n", adev->asic_type);
 	}
+
+	/* Determine whether to enable PSR support by default. */
+	if (!(amdgpu_dc_debug_mask & DC_DISABLE_PSR)) {
+		switch (adev->asic_type) {
+		case CHIP_VANGOGH:
+		case CHIP_YELLOW_CARP:
+			psr_feature_enabled = true;
+			break;
+		default:
+			psr_feature_enabled = amdgpu_dc_feature_mask & DC_PSR_MASK;
+			break;
+		}
+	}
 #endif
 
 	/* loops over all connectors on the board */
@@ -3839,8 +4418,16 @@
 		} else if (dc_link_detect(link, DETECT_REASON_BOOT)) {
 			amdgpu_dm_update_connector_after_detect(aconnector);
 			register_backlight_device(dm, link);
-			if (amdgpu_dc_feature_mask & DC_PSR_MASK)
+			if (dm->num_of_edps)
+				update_connector_ext_caps(aconnector);
+			if (psr_feature_enabled)
 				amdgpu_dm_set_psr_caps(link);
+
+			/* TODO: Fix vblank control helpers to delay PSR entry to allow this when
+			 * PSR is also supported.
+			 */
+			if (link->psr_settings.psr_feature_enabled)
+				adev_to_drm(adev)->vblank_disable_immediate = false;
 		}
 
 
@@ -3979,6 +4566,17 @@
 static int dm_early_init(void *handle)
 {
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
+	struct amdgpu_mode_info *mode_info = &adev->mode_info;
+	struct atom_context *ctx = mode_info->atom_context;
+	int index = GetIndexIntoMasterTable(DATA, Object_Header);
+	u16 data_offset;
+
+	/* if there is no object header, skip DM */
+	if (!amdgpu_atom_parse_data_header(ctx, index, NULL, NULL, NULL, &data_offset)) {
+		adev->harvest_ip_mask |= AMD_HARVEST_IP_DMU_MASK;
+		dev_info(adev->dev, "No object header, skipping DM\n");
+		return -ENOENT;
+	}
 
 	switch (adev->asic_type) {
 #if defined(CONFIG_DRM_AMD_DC_SI)
@@ -5033,7 +5631,7 @@
 	plane_info->visible = true;
 	plane_info->stereo_format = PLANE_STEREO_FORMAT_NONE;
 
-	plane_info->layer_index = 0;
+	plane_info->layer_index = plane_state->normalized_zpos;
 
 	ret = fill_plane_color_attributes(plane_state, plane_info->format,
 					  &plane_info->color_space);
@@ -5100,7 +5698,7 @@
 	dc_plane_state->global_alpha = plane_info.global_alpha;
 	dc_plane_state->global_alpha_value = plane_info.global_alpha_value;
 	dc_plane_state->dcc = plane_info.dcc;
-	dc_plane_state->layer_index = plane_info.layer_index; // Always returns 0
+	dc_plane_state->layer_index = plane_info.layer_index;
 	dc_plane_state->flip_int_enabled = true;
 
 	/*
@@ -5402,8 +6000,6 @@
 
 	timing_out->aspect_ratio = get_aspect_ratio(mode_in);
 
-	stream->output_color_space = get_output_color_space(timing_out);
-
 	stream->out_transfer_func->type = TF_TYPE_PREDEFINED;
 	stream->out_transfer_func->tf = TRANSFER_FUNCTION_SRGB;
 	if (stream->signal == SIGNAL_TYPE_HDMI_TYPE_A) {
@@ -5414,6 +6010,8 @@
 			adjust_colour_depth_from_display_info(timing_out, info);
 		}
 	}
+
+	stream->output_color_space = get_output_color_space(timing_out);
 }
 
 static void fill_audio_info(struct audio_info *audio_info,
@@ -5587,6 +6185,7 @@
 							struct dsc_dec_dpcd_caps *dsc_caps)
 {
 	stream->timing.flags.DSC = 0;
+	dsc_caps->is_dsc_supported = false;
 
 	if (aconnector->dc_link && sink->sink_signal == SIGNAL_TYPE_DISPLAY_PORT) {
 		dc_dsc_parse_dsc_dpcd(aconnector->dc_link->ctx->dc,
@@ -5717,7 +6316,7 @@
 		}
 	}
 
-	aconnector->freesync_vid_base = *m_pref;
+	drm_mode_copy(&aconnector->freesync_vid_base, m_pref);
 	return m_pref;
 }
 
@@ -5831,8 +6430,10 @@
 				 is_freesync_video_mode(&mode, aconnector);
 		if (recalculate_timing) {
 			freesync_mode = get_highest_refresh_rate_mode(aconnector, false);
-			saved_mode = mode;
-			mode = *freesync_mode;
+			drm_mode_copy(&saved_mode, &mode);
+			saved_mode.picture_aspect_ratio = mode.picture_aspect_ratio;
+			drm_mode_copy(&mode, freesync_mode);
+			mode.picture_aspect_ratio = saved_mode.picture_aspect_ratio;
 		} else {
 			decide_crtc_timing_for_drm_display_mode(
 				&mode, preferred_mode, scale);
@@ -6379,7 +6980,8 @@
 		aconnector->dc_sink = aconnector->dc_link->local_sink ?
 		aconnector->dc_link->local_sink :
 		aconnector->dc_em_sink;
-		dc_sink_retain(aconnector->dc_sink);
+		if (aconnector->dc_sink)
+			dc_sink_retain(aconnector->dc_sink);
 	}
 }
 
@@ -7527,6 +8129,9 @@
 		mode = amdgpu_dm_create_common_mode(encoder,
 				common_modes[i].name, common_modes[i].w,
 				common_modes[i].h);
+		if (!mode)
+			continue;
+
 		drm_mode_probed_add(connector, mode);
 		amdgpu_dm_connector->num_modes++;
 	}
@@ -7710,7 +8315,8 @@
 				drm_add_modes_noedid(connector, 640, 480);
 	} else {
 		amdgpu_dm_connector_ddc_get_modes(connector, edid);
-		amdgpu_dm_connector_add_common_modes(encoder, connector);
+		if (encoder)
+			amdgpu_dm_connector_add_common_modes(encoder, connector);
 		amdgpu_dm_connector_add_freesync_modes(connector, edid);
 	}
 	amdgpu_dm_fbc_init(connector);
@@ -7755,7 +8361,17 @@
 		break;
 	case DRM_MODE_CONNECTOR_DisplayPort:
 		aconnector->base.polled = DRM_CONNECTOR_POLL_HPD;
-		aconnector->base.ycbcr_420_allowed =
+		if (link->is_dig_mapping_flexible &&
+		    link->dc->res_pool->funcs->link_encs_assign) {
+			link->link_enc =
+				link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
+			if (!link->link_enc)
+				link->link_enc =
+					link_enc_cfg_get_next_avail_link_enc(link->ctx->dc);
+		}
+
+		if (link->link_enc)
+			aconnector->base.ycbcr_420_allowed =
 			link->link_enc->features.dp_ycbcr420_supported ? true : false;
 		break;
 	case DRM_MODE_CONNECTOR_DVID:
@@ -7870,7 +8486,8 @@
 	snprintf(i2c->base.name, sizeof(i2c->base.name), "AMDGPU DM i2c hw bus %d", link_index);
 	i2c_set_adapdata(&i2c->base, i2c);
 	i2c->ddc_service = ddc_service;
-	i2c->ddc_service->ddc_pin->hw_info.ddc_channel = link_index;
+	if (i2c->ddc_service->ddc_pin)
+		i2c->ddc_service->ddc_pin->hw_info.ddc_channel = link_index;
 
 	return i2c;
 }
@@ -8067,27 +8684,55 @@
 }
 
 #ifdef CONFIG_DRM_AMD_DC_HDCP
-static bool is_content_protection_different(struct drm_connector_state *state,
-					    const struct drm_connector_state *old_state,
-					    const struct drm_connector *connector, struct hdcp_workqueue *hdcp_w)
+static bool is_content_protection_different(struct drm_crtc_state *new_crtc_state,
+					    struct drm_crtc_state *old_crtc_state,
+					    struct drm_connector_state *new_conn_state,
+					    struct drm_connector_state *old_conn_state,
+					    const struct drm_connector *connector,
+					    struct hdcp_workqueue *hdcp_w)
 {
 	struct amdgpu_dm_connector *aconnector = to_amdgpu_dm_connector(connector);
 	struct dm_connector_state *dm_con_state = to_dm_connector_state(connector->state);
 
-	/* Handle: Type0/1 change */
-	if (old_state->hdcp_content_type != state->hdcp_content_type &&
-	    state->content_protection != DRM_MODE_CONTENT_PROTECTION_UNDESIRED) {
-		state->content_protection = DRM_MODE_CONTENT_PROTECTION_DESIRED;
+	pr_debug("[HDCP_DM] connector->index: %x connect_status: %x dpms: %x\n",
+		connector->index, connector->status, connector->dpms);
+	pr_debug("[HDCP_DM] state protection old: %x new: %x\n",
+		old_conn_state->content_protection, new_conn_state->content_protection);
+
+	if (old_crtc_state)
+		pr_debug("[HDCP_DM] old crtc en: %x a: %x m: %x a-chg: %x c-chg: %x\n",
+		old_crtc_state->enable,
+		old_crtc_state->active,
+		old_crtc_state->mode_changed,
+		old_crtc_state->active_changed,
+		old_crtc_state->connectors_changed);
+
+	if (new_crtc_state)
+		pr_debug("[HDCP_DM] NEW crtc en: %x a: %x m: %x a-chg: %x c-chg: %x\n",
+		new_crtc_state->enable,
+		new_crtc_state->active,
+		new_crtc_state->mode_changed,
+		new_crtc_state->active_changed,
+		new_crtc_state->connectors_changed);
+
+	/* hdcp content type change */
+	if (old_conn_state->hdcp_content_type != new_conn_state->hdcp_content_type &&
+	    new_conn_state->content_protection != DRM_MODE_CONTENT_PROTECTION_UNDESIRED) {
+		new_conn_state->content_protection = DRM_MODE_CONTENT_PROTECTION_DESIRED;
+		pr_debug("[HDCP_DM] Type0/1 change %s :true\n", __func__);
 		return true;
 	}
 
-	/* CP is being re enabled, ignore this
-	 *
-	 * Handles:	ENABLED -> DESIRED
-	 */
-	if (old_state->content_protection == DRM_MODE_CONTENT_PROTECTION_ENABLED &&
-	    state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED) {
-		state->content_protection = DRM_MODE_CONTENT_PROTECTION_ENABLED;
+	/* CP is being re enabled, ignore this */
+	if (old_conn_state->content_protection == DRM_MODE_CONTENT_PROTECTION_ENABLED &&
+	    new_conn_state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED) {
+		if (new_crtc_state && new_crtc_state->mode_changed) {
+			new_conn_state->content_protection = DRM_MODE_CONTENT_PROTECTION_DESIRED;
+			pr_debug("[HDCP_DM] ENABLED->DESIRED & mode_changed %s :true\n", __func__);
+			return true;
+		};
+		new_conn_state->content_protection = DRM_MODE_CONTENT_PROTECTION_ENABLED;
+		pr_debug("[HDCP_DM] ENABLED -> DESIRED %s :false\n", __func__);
 		return false;
 	}
 
@@ -8095,9 +8740,9 @@
 	 *
 	 * Handles:	UNDESIRED -> ENABLED
 	 */
-	if (old_state->content_protection == DRM_MODE_CONTENT_PROTECTION_UNDESIRED &&
-	    state->content_protection == DRM_MODE_CONTENT_PROTECTION_ENABLED)
-		state->content_protection = DRM_MODE_CONTENT_PROTECTION_DESIRED;
+	if (old_conn_state->content_protection == DRM_MODE_CONTENT_PROTECTION_UNDESIRED &&
+	    new_conn_state->content_protection == DRM_MODE_CONTENT_PROTECTION_ENABLED)
+		new_conn_state->content_protection = DRM_MODE_CONTENT_PROTECTION_DESIRED;
 
 	/* Stream removed and re-enabled
 	 *
@@ -8107,10 +8752,12 @@
 	 *
 	 * Handles:	DESIRED -> DESIRED (Special case)
 	 */
-	if (!(old_state->crtc && old_state->crtc->enabled) &&
-		state->crtc && state->crtc->enabled &&
+	if (!(old_conn_state->crtc && old_conn_state->crtc->enabled) &&
+		new_conn_state->crtc && new_conn_state->crtc->enabled &&
 		connector->state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED) {
 		dm_con_state->update_hdcp = false;
+		pr_debug("[HDCP_DM] DESIRED->DESIRED (Stream removed and re-enabled) %s :true\n",
+			__func__);
 		return true;
 	}
 
@@ -8122,35 +8769,42 @@
 	 *
 	 * Handles:	DESIRED -> DESIRED (Special case)
 	 */
-	if (dm_con_state->update_hdcp && state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED &&
-	    connector->dpms == DRM_MODE_DPMS_ON && aconnector->dc_sink != NULL) {
+	if (dm_con_state->update_hdcp &&
+	new_conn_state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED &&
+	connector->dpms == DRM_MODE_DPMS_ON && aconnector->dc_sink != NULL) {
 		dm_con_state->update_hdcp = false;
+		pr_debug("[HDCP_DM] DESIRED->DESIRED (Hot-plug, headless s3, dpms) %s :true\n",
+			__func__);
 		return true;
 	}
 
-	/*
-	 * Handles:	UNDESIRED -> UNDESIRED
-	 *		DESIRED -> DESIRED
-	 *		ENABLED -> ENABLED
-	 */
-	if (old_state->content_protection == state->content_protection)
+	if (old_conn_state->content_protection == new_conn_state->content_protection) {
+		if (new_conn_state->content_protection >= DRM_MODE_CONTENT_PROTECTION_DESIRED) {
+			if (new_crtc_state && new_crtc_state->mode_changed) {
+				pr_debug("[HDCP_DM] DESIRED->DESIRED or ENABLE->ENABLE mode_change %s :true\n",
+					__func__);
+				return true;
+			};
+			pr_debug("[HDCP_DM] DESIRED->DESIRED & ENABLE->ENABLE %s :false\n",
+				__func__);
+			return false;
+		};
+
+		pr_debug("[HDCP_DM] UNDESIRED->UNDESIRED %s :false\n", __func__);
 		return false;
+	}
 
-	/*
-	 * Handles:	UNDESIRED -> DESIRED
-	 *		DESIRED -> UNDESIRED
-	 *		ENABLED -> UNDESIRED
-	 */
-	if (state->content_protection != DRM_MODE_CONTENT_PROTECTION_ENABLED)
+	if (new_conn_state->content_protection != DRM_MODE_CONTENT_PROTECTION_ENABLED) {
+		pr_debug("[HDCP_DM] UNDESIRED->DESIRED or DESIRED->UNDESIRED or ENABLED->UNDESIRED %s :true\n",
+			__func__);
 		return true;
+	}
 
-	/*
-	 * Handles:	DESIRED -> ENABLED
-	 */
+	pr_debug("[HDCP_DM] DESIRED->ENABLED %s :false\n", __func__);
 	return false;
 }
-
 #endif
+
 static void remove_stream(struct amdgpu_device *adev,
 			  struct amdgpu_crtc *acrtc,
 			  struct dc_stream_state *stream)
@@ -8254,6 +8908,13 @@
 	attributes.rotation_angle    = 0;
 	attributes.attribute_flags.value = 0;
 
+	/* Enable cursor degamma ROM on DCN3+ for implicit sRGB degamma in DRM
+	 * legacy gamma setup.
+	 */
+	if (crtc_state->cm_is_degamma_srgb &&
+	    adev->dm.dc->caps.color.dpp.gamma_corr)
+		attributes.attribute_flags.bits.ENABLE_CURSOR_DEGAMMA = 1;
+
 	attributes.pitch = afb->base.pitches[0] / afb->base.format->cpp[0];
 
 	if (crtc_state->stream) {
@@ -8447,15 +9108,15 @@
 		 * We also need vupdate irq for the actual core vblank handling
 		 * at end of vblank.
 		 */
-		dm_set_vupdate_irq(new_state->base.crtc, true);
-		drm_crtc_vblank_get(new_state->base.crtc);
+		WARN_ON(dm_set_vupdate_irq(new_state->base.crtc, true) != 0);
+		WARN_ON(drm_crtc_vblank_get(new_state->base.crtc) != 0);
 		DRM_DEBUG_DRIVER("%s: crtc=%u VRR off->on: Get vblank ref\n",
 				 __func__, new_state->base.crtc->base.id);
 	} else if (old_vrr_active && !new_vrr_active) {
 		/* Transition VRR active -> inactive:
 		 * Allow vblank irq disable again for fixed refresh rate.
 		 */
-		dm_set_vupdate_irq(new_state->base.crtc, false);
+		WARN_ON(dm_set_vupdate_irq(new_state->base.crtc, false) != 0);
 		drm_crtc_vblank_put(new_state->base.crtc);
 		DRM_DEBUG_DRIVER("%s: crtc=%u VRR on->off: Drop vblank ref\n",
 				 __func__, new_state->base.crtc->base.id);
@@ -8477,6 +9138,13 @@
 			handle_cursor_update(plane, old_plane_state);
 }
 
+static inline uint32_t get_mem_type(struct drm_framebuffer *fb)
+{
+	struct amdgpu_bo *abo = gem_to_amdgpu_bo(fb->obj[0]);
+
+	return abo->tbo.resource ? abo->tbo.resource->mem_type : 0;
+}
+
 static void amdgpu_dm_commit_planes(struct drm_atomic_state *state,
 				    struct dc_state *dc_state,
 				    struct drm_device *dev,
@@ -8546,6 +9214,8 @@
 			continue;
 
 		dc_plane = dm_new_plane_state->dc_state;
+		if (!dc_plane)
+			continue;
 
 		bundle->surface_updates[planes_count].surface = dc_plane;
 		if (new_pcrtc_state->color_mgmt_changed) {
@@ -8597,11 +9267,13 @@
 
 		/*
 		 * Only allow immediate flips for fast updates that don't
-		 * change FB pitch, DCC state, rotation or mirroing.
+		 * change memory domain, FB pitch, DCC state, rotation or
+		 * mirroring.
 		 */
 		bundle->flip_addrs[planes_count].flip_immediate =
 			crtc->state->async_flip &&
-			acrtc_state->update_type == UPDATE_TYPE_FAST;
+			acrtc_state->update_type == UPDATE_TYPE_FAST &&
+			get_mem_type(old_plane_state->fb) == get_mem_type(fb);
 
 		timestamp_ns = ktime_get_ns();
 		bundle->flip_addrs[planes_count].flip_timestamp_in_us = div_u64(timestamp_ns, 1000);
@@ -8734,6 +9406,12 @@
 		if (acrtc_state->abm_level != dm_old_crtc_state->abm_level)
 			bundle->stream_update.abm_level = &acrtc_state->abm_level;
 
+		mutex_lock(&dm->dc_lock);
+		if ((acrtc_state->update_type > UPDATE_TYPE_FAST) &&
+				acrtc_state->stream->link->psr_settings.psr_allow_active)
+			amdgpu_dm_psr_disable(acrtc_state->stream);
+		mutex_unlock(&dm->dc_lock);
+
 		/*
 		 * If FreeSync state on the stream has changed then we need to
 		 * re-adjust the min/max bounds now that DC doesn't handle this
@@ -8747,16 +9425,13 @@
 			spin_unlock_irqrestore(&pcrtc->dev->event_lock, flags);
 		}
 		mutex_lock(&dm->dc_lock);
-		if ((acrtc_state->update_type > UPDATE_TYPE_FAST) &&
-				acrtc_state->stream->link->psr_settings.psr_allow_active)
-			amdgpu_dm_psr_disable(acrtc_state->stream);
 
-		dc_commit_updates_for_stream(dm->dc,
-						     bundle->surface_updates,
-						     planes_count,
-						     acrtc_state->stream,
-						     &bundle->stream_update,
-						     dc_state);
+		update_planes_and_stream_adapter(dm->dc,
+					 acrtc_state->update_type,
+					 planes_count,
+					 acrtc_state->stream,
+					 &bundle->stream_update,
+					 bundle->surface_updates);
 
 		/**
 		 * Enable or disable the interrupts on the backend.
@@ -9084,10 +9759,67 @@
 		struct amdgpu_crtc *acrtc = to_amdgpu_crtc(dm_new_con_state->base.crtc);
 		struct amdgpu_dm_connector *aconnector = to_amdgpu_dm_connector(connector);
 
+		if (!adev->dm.hdcp_workqueue)
+			continue;
+
+		pr_debug("[HDCP_DM] -------------- i : %x ----------\n", i);
+
+		if (!connector)
+			continue;
+
+		pr_debug("[HDCP_DM] connector->index: %x connect_status: %x dpms: %x\n",
+			connector->index, connector->status, connector->dpms);
+		pr_debug("[HDCP_DM] state protection old: %x new: %x\n",
+			old_con_state->content_protection, new_con_state->content_protection);
+
+		if (aconnector->dc_sink) {
+			if (aconnector->dc_sink->sink_signal != SIGNAL_TYPE_VIRTUAL &&
+				aconnector->dc_sink->sink_signal != SIGNAL_TYPE_NONE) {
+				pr_debug("[HDCP_DM] pipe_ctx dispname=%s\n",
+				aconnector->dc_sink->edid_caps.display_name);
+			}
+		}
+
 		new_crtc_state = NULL;
+		old_crtc_state = NULL;
 
-		if (acrtc)
+		if (acrtc) {
 			new_crtc_state = drm_atomic_get_new_crtc_state(state, &acrtc->base);
+			old_crtc_state = drm_atomic_get_old_crtc_state(state, &acrtc->base);
+		}
+
+		if (old_crtc_state)
+			pr_debug("old crtc en: %x a: %x m: %x a-chg: %x c-chg: %x\n",
+			old_crtc_state->enable,
+			old_crtc_state->active,
+			old_crtc_state->mode_changed,
+			old_crtc_state->active_changed,
+			old_crtc_state->connectors_changed);
+
+		if (new_crtc_state)
+			pr_debug("NEW crtc en: %x a: %x m: %x a-chg: %x c-chg: %x\n",
+			new_crtc_state->enable,
+			new_crtc_state->active,
+			new_crtc_state->mode_changed,
+			new_crtc_state->active_changed,
+			new_crtc_state->connectors_changed);
+	}
+
+	for_each_oldnew_connector_in_state(state, connector, old_con_state, new_con_state, i) {
+		struct dm_connector_state *dm_new_con_state = to_dm_connector_state(new_con_state);
+		struct amdgpu_crtc *acrtc = to_amdgpu_crtc(dm_new_con_state->base.crtc);
+		struct amdgpu_dm_connector *aconnector = to_amdgpu_dm_connector(connector);
+
+		if (!adev->dm.hdcp_workqueue)
+			continue;
+
+		new_crtc_state = NULL;
+		old_crtc_state = NULL;
+
+		if (acrtc) {
+			new_crtc_state = drm_atomic_get_new_crtc_state(state, &acrtc->base);
+			old_crtc_state = drm_atomic_get_old_crtc_state(state, &acrtc->base);
+		}
 
 		dm_new_crtc_state = to_dm_crtc_state(new_crtc_state);
 
@@ -9099,11 +9831,44 @@
 			continue;
 		}
 
-		if (is_content_protection_different(new_con_state, old_con_state, connector, adev->dm.hdcp_workqueue))
+		if (is_content_protection_different(new_crtc_state, old_crtc_state, new_con_state,
+											old_con_state, connector, adev->dm.hdcp_workqueue)) {
+			/* when display is unplugged from mst hub, connctor will
+			 * be destroyed within dm_dp_mst_connector_destroy. connector
+			 * hdcp perperties, like type, undesired, desired, enabled,
+			 * will be lost. So, save hdcp properties into hdcp_work within
+			 * amdgpu_dm_atomic_commit_tail. if the same display is
+			 * plugged back with same display index, its hdcp properties
+			 * will be retrieved from hdcp_work within dm_dp_mst_get_modes
+			 */
+
+			bool enable_encryption = false;
+
+			if (new_con_state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED)
+				enable_encryption = true;
+
+			if (aconnector->dc_link && aconnector->dc_sink &&
+				aconnector->dc_link->type == dc_connection_mst_branch) {
+				struct hdcp_workqueue *hdcp_work = adev->dm.hdcp_workqueue;
+				struct hdcp_workqueue *hdcp_w =
+					&hdcp_work[aconnector->dc_link->link_index];
+
+				hdcp_w->hdcp_content_type[connector->index] =
+					new_con_state->hdcp_content_type;
+				hdcp_w->content_protection[connector->index] =
+					new_con_state->content_protection;
+			}
+
+			if (new_crtc_state && new_crtc_state->mode_changed &&
+				new_con_state->content_protection >= DRM_MODE_CONTENT_PROTECTION_DESIRED)
+				enable_encryption = true;
+
+			DRM_INFO("[HDCP_DM] hdcp_update_display enable_encryption = %x\n", enable_encryption);
+
 			hdcp_update_display(
 				adev->dm.hdcp_workqueue, aconnector->dc_link->link_index, aconnector,
-				new_con_state->hdcp_content_type,
-				new_con_state->content_protection == DRM_MODE_CONTENT_PROTECTION_DESIRED);
+				new_con_state->hdcp_content_type, enable_encryption);
+		}
 	}
 #endif
 
@@ -9182,32 +9947,14 @@
 
 
 		mutex_lock(&dm->dc_lock);
-		dc_commit_updates_for_stream(dm->dc,
-						     dummy_updates,
-						     status->plane_count,
-						     dm_new_crtc_state->stream,
-						     &stream_update,
-						     dc_state);
+		dc_update_planes_and_stream(dm->dc,
+					    dummy_updates,
+					    status->plane_count,
+					    dm_new_crtc_state->stream,
+					    &stream_update);
 		mutex_unlock(&dm->dc_lock);
 	}
 
-	/* Count number of newly disabled CRTCs for dropping PM refs later. */
-	for_each_oldnew_crtc_in_state(state, crtc, old_crtc_state,
-				      new_crtc_state, i) {
-		if (old_crtc_state->active && !new_crtc_state->active)
-			crtc_disable_count++;
-
-		dm_new_crtc_state = to_dm_crtc_state(new_crtc_state);
-		dm_old_crtc_state = to_dm_crtc_state(old_crtc_state);
-
-		/* For freesync config update on crtc state and params for irq */
-		update_stream_irq_parameters(dm, dm_new_crtc_state);
-
-		/* Handle vrr on->off / off->on transitions */
-		amdgpu_dm_handle_vrr_transition(dm_old_crtc_state,
-						dm_new_crtc_state);
-	}
-
 	/**
 	 * Enable interrupts for CRTCs that are newly enabled or went through
 	 * a modeset. It was intentionally deferred until after the front end
@@ -9217,16 +9964,29 @@
 	for_each_oldnew_crtc_in_state(state, crtc, old_crtc_state, new_crtc_state, i) {
 		struct amdgpu_crtc *acrtc = to_amdgpu_crtc(crtc);
 #ifdef CONFIG_DEBUG_FS
-		bool configure_crc = false;
 		enum amdgpu_dm_pipe_crc_source cur_crc_src;
 #if defined(CONFIG_DRM_AMD_SECURE_DISPLAY)
-		struct crc_rd_work *crc_rd_wrk = dm->crc_rd_wrk;
+		struct crc_rd_work *crc_rd_wrk;
+#endif
+#endif
+		/* Count number of newly disabled CRTCs for dropping PM refs later. */
+		if (old_crtc_state->active && !new_crtc_state->active)
+			crtc_disable_count++;
+
+		dm_new_crtc_state = to_dm_crtc_state(new_crtc_state);
+		dm_old_crtc_state = to_dm_crtc_state(old_crtc_state);
+
+		/* For freesync config update on crtc state and params for irq */
+		update_stream_irq_parameters(dm, dm_new_crtc_state);
+
+#ifdef CONFIG_DEBUG_FS
+#if defined(CONFIG_DRM_AMD_SECURE_DISPLAY)
+		crc_rd_wrk = dm->crc_rd_wrk;
 #endif
 		spin_lock_irqsave(&adev_to_drm(adev)->event_lock, flags);
 		cur_crc_src = acrtc->dm_irq_params.crc_src;
 		spin_unlock_irqrestore(&adev_to_drm(adev)->event_lock, flags);
 #endif
-		dm_new_crtc_state = to_dm_crtc_state(new_crtc_state);
 
 		if (new_crtc_state->active &&
 		    (!old_crtc_state->active ||
@@ -9234,16 +9994,19 @@
 			dc_stream_retain(dm_new_crtc_state->stream);
 			acrtc->dm_irq_params.stream = dm_new_crtc_state->stream;
 			manage_dm_interrupts(adev, acrtc, true);
+		}
+		/* Handle vrr on->off / off->on transitions */
+		amdgpu_dm_handle_vrr_transition(dm_old_crtc_state, dm_new_crtc_state);
 
 #ifdef CONFIG_DEBUG_FS
+		if (new_crtc_state->active &&
+		    (!old_crtc_state->active ||
+		     drm_atomic_crtc_needs_modeset(new_crtc_state))) {
 			/**
 			 * Frontend may have changed so reapply the CRC capture
 			 * settings for the stream.
 			 */
-			dm_new_crtc_state = to_dm_crtc_state(new_crtc_state);
-
 			if (amdgpu_dm_is_valid_crc_source(cur_crc_src)) {
-				configure_crc = true;
 #if defined(CONFIG_DRM_AMD_SECURE_DISPLAY)
 				if (amdgpu_dm_crc_window_is_activated(crtc)) {
 					spin_lock_irqsave(&adev_to_drm(adev)->event_lock, flags);
@@ -9255,14 +10018,12 @@
 					spin_unlock_irqrestore(&adev_to_drm(adev)->event_lock, flags);
 				}
 #endif
-			}
-
-			if (configure_crc)
 				if (amdgpu_dm_crtc_configure_crc_source(
 					crtc, dm_new_crtc_state, cur_crc_src))
 					DRM_DEBUG_DRIVER("Failed to configure crc source");
-#endif
+			}
 		}
+#endif
 	}
 
 	for_each_new_crtc_in_state(state, crtc, new_crtc_state, j)
@@ -9286,7 +10047,7 @@
 	/* restore the backlight level */
 	for (i = 0; i < dm->num_of_edps; i++) {
 		if (dm->backlight_dev[i] &&
-		    (amdgpu_dm_backlight_get_level(dm, i) != dm->brightness[i]))
+		    (dm->actual_brightness[i] != dm->brightness[i]))
 			amdgpu_dm_backlight_set_level(dm, i, dm->brightness[i]);
 	}
 #endif
@@ -9686,7 +10447,16 @@
 		if (!dm_old_crtc_state->stream)
 			goto skip_modeset;
 
+		/* Unset freesync video if it was active before */
+		if (dm_old_crtc_state->freesync_config.state == VRR_STATE_ACTIVE_FIXED) {
+			dm_new_crtc_state->freesync_config.state = VRR_STATE_INACTIVE;
+			dm_new_crtc_state->freesync_config.fixed_refresh_in_uhz = 0;
+		}
+
+		/* Now check if we should set freesync video mode */
 		if (amdgpu_freesync_vid_mode && dm_new_crtc_state->stream &&
+		    dc_is_stream_unchanged(new_stream, dm_old_crtc_state->stream) &&
+		    dc_is_stream_scaling_unchanged(new_stream, dm_old_crtc_state->stream) &&
 		    is_timing_unchanged_for_freesync(new_crtc_state,
 						     old_crtc_state)) {
 			new_crtc_state->mode_changed = false;
@@ -9738,7 +10508,7 @@
 		 * added MST connectors not found in existing crtc_state in the chained mode
 		 * TODO: need to dig out the root cause of that
 		 */
-		if (!aconnector || (!aconnector->dc_sink && aconnector->mst_port))
+		if (!aconnector)
 			goto skip_modeset;
 
 		if (modereset_required(new_crtc_state))
@@ -10070,8 +10840,9 @@
 			return -EINVAL;
 		}
 
+		if (dm_old_plane_state->dc_state)
+			dc_plane_state_release(dm_old_plane_state->dc_state);
 
-		dc_plane_state_release(dm_old_plane_state->dc_state);
 		dm_new_plane_state->dc_state = NULL;
 
 		*lock_and_validation_needed = true;
@@ -10196,10 +10967,13 @@
 static int add_affected_mst_dsc_crtcs(struct drm_atomic_state *state, struct drm_crtc *crtc)
 {
 	struct drm_connector *connector;
-	struct drm_connector_state *conn_state;
+	struct drm_connector_state *conn_state, *old_conn_state;
 	struct amdgpu_dm_connector *aconnector = NULL;
 	int i;
-	for_each_new_connector_in_state(state, connector, conn_state, i) {
+	for_each_oldnew_connector_in_state(state, connector, old_conn_state, conn_state, i) {
+		if (!conn_state->crtc)
+			conn_state = old_conn_state;
+
 		if (conn_state->crtc != crtc)
 			continue;
 
@@ -10332,8 +11106,8 @@
 			goto fail;
 		}
 
-		if (dm_old_con_state->abm_level !=
-		    dm_new_con_state->abm_level)
+		if (dm_old_con_state->abm_level != dm_new_con_state->abm_level ||
+		    dm_old_con_state->scaling != dm_new_con_state->scaling)
 			new_crtc_state->connectors_changed = true;
 	}
 
@@ -10412,6 +11186,18 @@
 		}
 	}
 
+	/*
+	 * DC consults the zpos (layer_index in DC terminology) to determine the
+	 * hw plane on which to enable the hw cursor (see
+	 * `dcn10_can_pipe_disable_cursor`). By now, all modified planes are in
+	 * atomic state, so call drm helper to normalize zpos.
+	 */
+	ret = drm_atomic_normalize_zpos(dev, state);
+	if (ret) {
+		drm_dbg(dev, "drm_atomic_normalize_zpos() failed\n");
+		goto fail;
+	}
+
 	/* Remove exiting planes if they are modified */
 	for_each_oldnew_plane_in_state_reverse(state, plane, old_plane_state, new_plane_state, i) {
 		ret = dm_update_plane_state(dc, state, plane,
@@ -10982,29 +11768,75 @@
 	return value;
 }
 
-int amdgpu_dm_process_dmub_aux_transfer_sync(struct dc_context *ctx, unsigned int linkIndex,
-				struct aux_payload *payload, enum aux_return_code_type *operation_result)
+int amdgpu_dm_set_dmub_async_sync_status(bool is_cmd_aux, struct dc_context *ctx,
+	uint8_t status_type, uint32_t *operation_result)
+{
+	struct amdgpu_device *adev = ctx->driver_context;
+	int return_status = -1;
+	struct dmub_notification *p_notify = adev->dm.dmub_notify;
+
+	if (is_cmd_aux) {
+		if (status_type == DMUB_ASYNC_TO_SYNC_ACCESS_SUCCESS) {
+			return_status = p_notify->aux_reply.length;
+			*operation_result = p_notify->result;
+		} else if (status_type == DMUB_ASYNC_TO_SYNC_ACCESS_TIMEOUT) {
+			*operation_result = AUX_RET_ERROR_TIMEOUT;
+		} else if (status_type == DMUB_ASYNC_TO_SYNC_ACCESS_FAIL) {
+			*operation_result = AUX_RET_ERROR_ENGINE_ACQUIRE;
+		} else {
+			*operation_result = AUX_RET_ERROR_UNKNOWN;
+		}
+	} else {
+		if (status_type == DMUB_ASYNC_TO_SYNC_ACCESS_SUCCESS) {
+			return_status = 0;
+			*operation_result = p_notify->sc_status;
+		} else {
+			*operation_result = SET_CONFIG_UNKNOWN_ERROR;
+		}
+	}
+
+	return return_status;
+}
+
+int amdgpu_dm_process_dmub_aux_transfer_sync(bool is_cmd_aux, struct dc_context *ctx,
+	unsigned int link_index, void *cmd_payload, void *operation_result)
 {
 	struct amdgpu_device *adev = ctx->driver_context;
 	int ret = 0;
 
-	dc_process_dmub_aux_transfer_async(ctx->dc, linkIndex, payload);
-	ret = wait_for_completion_interruptible_timeout(&adev->dm.dmub_aux_transfer_done, 10*HZ);
-	if (ret == 0) {
-		*operation_result = AUX_RET_ERROR_TIMEOUT;
-		return -1;
+	if (is_cmd_aux) {
+		dc_process_dmub_aux_transfer_async(ctx->dc,
+			link_index, (struct aux_payload *)cmd_payload);
+	} else if (dc_process_dmub_set_config_async(ctx->dc, link_index,
+					(struct set_config_cmd_payload *)cmd_payload,
+					adev->dm.dmub_notify)) {
+		return amdgpu_dm_set_dmub_async_sync_status(is_cmd_aux,
+					ctx, DMUB_ASYNC_TO_SYNC_ACCESS_SUCCESS,
+					(uint32_t *)operation_result);
 	}
-	*operation_result = (enum aux_return_code_type)adev->dm.dmub_notify->result;
 
-	if (adev->dm.dmub_notify->result == AUX_RET_SUCCESS) {
-		(*payload->reply) = adev->dm.dmub_notify->aux_reply.command;
+	ret = wait_for_completion_timeout(&adev->dm.dmub_aux_transfer_done, 10 * HZ);
+	if (ret == 0) {
+		DRM_ERROR("wait_for_completion_timeout timeout!");
+		return amdgpu_dm_set_dmub_async_sync_status(is_cmd_aux,
+				ctx, DMUB_ASYNC_TO_SYNC_ACCESS_TIMEOUT,
+				(uint32_t *)operation_result);
+	}
 
-		// For read case, Copy data to payload
-		if (!payload->write && adev->dm.dmub_notify->aux_reply.length &&
-		(*payload->reply == AUX_TRANSACTION_REPLY_AUX_ACK))
-			memcpy(payload->data, adev->dm.dmub_notify->aux_reply.data,
-			adev->dm.dmub_notify->aux_reply.length);
+	if (is_cmd_aux) {
+		if (adev->dm.dmub_notify->result == AUX_RET_SUCCESS) {
+			struct aux_payload *payload = (struct aux_payload *)cmd_payload;
+
+			payload->reply[0] = adev->dm.dmub_notify->aux_reply.command;
+			if (!payload->write && adev->dm.dmub_notify->aux_reply.length &&
+			    payload->reply[0] == AUX_TRANSACTION_REPLY_AUX_ACK) {
+				memcpy(payload->data, adev->dm.dmub_notify->aux_reply.data,
+				       adev->dm.dmub_notify->aux_reply.length);
+			}
+		}
 	}
 
-	return adev->dm.dmub_notify->aux_reply.length;
+	return amdgpu_dm_set_dmub_async_sync_status(is_cmd_aux,
+			ctx, DMUB_ASYNC_TO_SYNC_ACCESS_SUCCESS,
+			(uint32_t *)operation_result);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h
@@ -47,6 +47,15 @@
 #define AMDGPU_DM_MAX_CRTC 6
 
 #define AMDGPU_DM_MAX_NUM_EDP 2
+
+#define AMDGPU_DMUB_NOTIFICATION_MAX 6
+
+/**
+ * DMUB Async to Sync Mechanism Status
+ **/
+#define DMUB_ASYNC_TO_SYNC_ACCESS_FAIL 1
+#define DMUB_ASYNC_TO_SYNC_ACCESS_TIMEOUT 2
+#define DMUB_ASYNC_TO_SYNC_ACCESS_SUCCESS 3
 /*
 #include "include/amdgpu_dal_power_if.h"
 #include "amdgpu_dm_irq.h"
@@ -86,6 +95,21 @@
 	uint64_t gpu_addr;
 };
 
+typedef void (*dmub_notify_interrupt_callback_t)(struct amdgpu_device *adev, struct dmub_notification *notify);
+
+/**
+ * struct dmub_hpd_work - Handle time consuming work in low priority outbox IRQ
+ *
+ * @handle_hpd_work: Work to be executed in a separate thread to handle hpd_low_irq
+ * @dmub_notify:  notification for callback function
+ * @adev: amdgpu_device pointer
+ */
+struct dmub_hpd_work {
+	struct work_struct handle_hpd_work;
+	struct dmub_notification *dmub_notify;
+	struct amdgpu_device *adev;
+};
+
 /**
  * struct vblank_control_work - Work data for vblank control
  * @work: Kernel work data for the work event
@@ -155,6 +179,48 @@
 };
 
 /**
+ * struct hpd_rx_irq_offload_work_queue - Work queue to handle hpd_rx_irq
+ * offload work
+ */
+struct hpd_rx_irq_offload_work_queue {
+	/**
+	 * @wq: workqueue structure to queue offload work.
+	 */
+	struct workqueue_struct *wq;
+	/**
+	 * @offload_lock: To protect fields of offload work queue.
+	 */
+	spinlock_t offload_lock;
+	/**
+	 * @is_handling_link_loss: Used to prevent inserting link loss event when
+	 * we're handling link loss
+	 */
+	bool is_handling_link_loss;
+	/**
+	 * @aconnector: The aconnector that this work queue is attached to
+	 */
+	struct amdgpu_dm_connector *aconnector;
+};
+
+/**
+ * struct hpd_rx_irq_offload_work - hpd_rx_irq offload work structure
+ */
+struct hpd_rx_irq_offload_work {
+	/**
+	 * @work: offload work
+	 */
+	struct work_struct work;
+	/**
+	 * @data: reference irq data which is used while handling offload work
+	 */
+	union hpd_irq_data data;
+	/**
+	 * @offload_wq: offload work queue that this work is queued to
+	 */
+	struct hpd_rx_irq_offload_work_queue *offload_wq;
+};
+
+/**
  * struct amdgpu_display_manager - Central amdgpu display manager device
  *
  * @dc: Display Core control structure
@@ -190,9 +256,31 @@
 	 */
 	struct dmub_srv *dmub_srv;
 
+	/**
+	 * @dmub_notify:
+	 *
+	 * Notification from DMUB.
+	 */
+
 	struct dmub_notification *dmub_notify;
 
 	/**
+	 * @dmub_callback:
+	 *
+	 * Callback functions to handle notification from DMUB.
+	 */
+
+	dmub_notify_interrupt_callback_t dmub_callback[AMDGPU_DMUB_NOTIFICATION_MAX];
+
+	/**
+	 * @dmub_thread_offload:
+	 *
+	 * Flag to indicate if callback is offload.
+	 */
+
+	bool dmub_thread_offload[AMDGPU_DMUB_NOTIFICATION_MAX];
+
+	/**
 	 * @dmub_fb_info:
 	 *
 	 * Framebuffer regions for the DMUB.
@@ -422,7 +510,12 @@
 	 */
 	struct crc_rd_work *crc_rd_wrk;
 #endif
-
+	/**
+	 * @hpd_rx_offload_wq:
+	 *
+	 * Work queue to offload works of hpd_rx_irq
+	 */
+	struct hpd_rx_irq_offload_work_queue *hpd_rx_offload_wq;
 	/**
 	 * @mst_encoders:
 	 *
@@ -439,6 +532,7 @@
 	 */
 	struct list_head da_list;
 	struct completion dmub_aux_transfer_done;
+	struct workqueue_struct *delayed_hpd_wq;
 
 	/**
 	 * @brightness:
@@ -446,6 +540,20 @@
 	 * cached backlight values.
 	 */
 	u32 brightness[AMDGPU_DM_MAX_NUM_EDP];
+	/**
+	 * @actual_brightness:
+	 *
+	 * last successfully applied backlight values.
+	 */
+	u32 actual_brightness[AMDGPU_DM_MAX_NUM_EDP];
+
+	/**
+	 * @aux_hpd_discon_quirk:
+	 *
+	 * quirk for hpd discon while aux is on-going.
+	 * occurred on certain intel platform
+	 */
+	bool aux_hpd_discon_quirk;
 };
 
 enum dsc_clock_force_state {
@@ -632,6 +740,7 @@
 
 extern const struct drm_encoder_helper_funcs amdgpu_dm_encoder_helper_funcs;
 
-int amdgpu_dm_process_dmub_aux_transfer_sync(struct dc_context *ctx, unsigned int linkIndex,
-					struct aux_payload *payload, enum aux_return_code_type *operation_result);
+int amdgpu_dm_process_dmub_aux_transfer_sync(bool is_cmd_aux,
+					struct dc_context *ctx, unsigned int link_index,
+					void *payload, void *operation_result);
 #endif /* __AMDGPU_DM_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_crc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_crc.c
@@ -314,6 +314,14 @@
 			ret = -EINVAL;
 			goto cleanup;
 		}
+
+		if ((aconn->base.connector_type != DRM_MODE_CONNECTOR_DisplayPort) &&
+				(aconn->base.connector_type != DRM_MODE_CONNECTOR_eDP)) {
+			DRM_DEBUG_DRIVER("No DP connector available for CRC source\n");
+			ret = -EINVAL;
+			goto cleanup;
+		}
+
 	}
 
 #if defined(CONFIG_DRM_AMD_SECURE_DISPLAY)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_debugfs.c
@@ -229,8 +229,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -247,6 +249,7 @@
 {
 	struct amdgpu_dm_connector *connector = file_inode(f)->i_private;
 	struct dc_link *link = connector->dc_link;
+	struct dc *dc = (struct dc *)link->dc;
 	struct dc_link_settings prefer_link_settings;
 	char *wr_buf = NULL;
 	const uint32_t wr_buf_size = 40;
@@ -313,7 +316,7 @@
 	prefer_link_settings.lane_count = param[0];
 	prefer_link_settings.link_rate = param[1];
 
-	dp_retrain_link_dp_test(link, &prefer_link_settings, false);
+	dc_link_set_preferred_training_settings(dc, &prefer_link_settings, NULL, link, true);
 
 	kfree(wr_buf);
 	return size;
@@ -387,8 +390,10 @@
 			break;
 
 		r = put_user((*(rd_buf + result)), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -1299,7 +1304,7 @@
 	const uint32_t rd_buf_size = 10;
 	struct pipe_ctx *pipe_ctx;
 	ssize_t result = 0;
-	int i, r, str_len = 30;
+	int i, r, str_len = 10;
 
 	rd_buf = kcalloc(rd_buf_size, sizeof(char), GFP_KERNEL);
 
@@ -1310,14 +1315,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -1332,8 +1336,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -1412,12 +1418,14 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx || !pipe_ctx->stream)
+	if (!pipe_ctx->stream)
 		goto done;
 
 	// Get CRTC state
@@ -1497,14 +1505,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -1519,8 +1526,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -1597,12 +1606,14 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx || !pipe_ctx->stream)
+	if (!pipe_ctx->stream)
 		goto done;
 
 	// Safely get CRTC state
@@ -1682,14 +1693,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -1704,8 +1714,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -1782,12 +1794,14 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx || !pipe_ctx->stream)
+	if (!pipe_ctx->stream)
 		goto done;
 
 	// Get CRTC state
@@ -1863,14 +1877,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -1885,8 +1898,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -1960,12 +1975,14 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx || !pipe_ctx->stream)
+	if (!pipe_ctx->stream)
 		goto done;
 
 	// Get CRTC state
@@ -2039,14 +2056,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -2061,8 +2077,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -2096,14 +2114,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -2118,8 +2135,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -2168,14 +2187,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -2190,8 +2208,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -2240,14 +2260,13 @@
 
 	for (i = 0; i < MAX_PIPES; i++) {
 		pipe_ctx = &aconnector->dc_link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream &&
-			    pipe_ctx->stream->link == aconnector->dc_link)
-				break;
+		if (pipe_ctx->stream &&
+		    pipe_ctx->stream->link == aconnector->dc_link &&
+		    pipe_ctx->stream->sink &&
+		    pipe_ctx->stream->sink == aconnector->dc_sink)
+			break;
 	}
 
-	if (!pipe_ctx)
-		return -ENXIO;
-
 	dsc = pipe_ctx->stream_res.dsc;
 	if (dsc)
 		dsc->funcs->dsc_read_state(dsc, &dsc_state);
@@ -2262,8 +2281,10 @@
 			break;
 
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 
 		buf += 1;
 		size -= 1;
@@ -2907,10 +2928,13 @@
 	struct amdgpu_device *adev = drm_to_adev(new_crtc->dev);
 	struct crc_rd_work *crc_rd_wrk = adev->dm.crc_rd_wrk;
 
+	if (!crc_rd_wrk)
+		return 0;
+
 	if (val) {
 		spin_lock_irq(&adev_to_drm(adev)->event_lock);
 		spin_lock_irq(&crc_rd_wrk->crc_rd_work_lock);
-		if (crc_rd_wrk && crc_rd_wrk->crtc) {
+		if (crc_rd_wrk->crtc) {
 			old_crtc = crc_rd_wrk->crtc;
 			old_acrtc = to_amdgpu_crtc(old_crtc);
 		}
@@ -2967,7 +2991,7 @@
 				   &crc_win_y_end_fops);
 	debugfs_create_file_unsafe("crc_win_update", 0644, dir, crtc,
 				   &crc_win_update_fops);
-
+	dput(dir);
 }
 #endif
 /*
@@ -3250,8 +3274,10 @@
 	dc->hwss.get_dcc_en_bits(dc, dcc_en_bits);
 
 	rd_buf = kcalloc(rd_buf_size, sizeof(char), GFP_KERNEL);
-	if (!rd_buf)
+	if (!rd_buf) {
+		kfree(dcc_en_bits);
 		return -ENOMEM;
+	}
 
 	for (i = 0; i < num_pipes; i++)
 		offset += snprintf(rd_buf + offset, rd_buf_size - offset,
@@ -3264,8 +3290,10 @@
 		if (*pos >= rd_buf_size)
 			break;
 		r = put_user(*(rd_buf + result), buf);
-		if (r)
+		if (r) {
+			kfree(rd_buf);
 			return r; /* r = -EFAULT */
+		}
 		buf += 1;
 		size -= 1;
 		*pos += 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_hdcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_hdcp.c
@@ -396,6 +396,7 @@
 	for (i = 0; i < hdcp_work->max_link; i++) {
 		cancel_delayed_work_sync(&hdcp_work[i].callback_dwork);
 		cancel_delayed_work_sync(&hdcp_work[i].watchdog_timer_dwork);
+		cancel_delayed_work_sync(&hdcp_work[i].property_validate_dwork);
 	}
 
 	sysfs_remove_bin_file(kobj, &hdcp_work[0].attr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_hdcp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_hdcp.h
@@ -52,6 +52,20 @@
 	struct mod_hdcp_link link;
 
 	enum mod_hdcp_encryption_status encryption_status;
+
+	/* when display is unplugged from mst hub, connctor will be
+	 * destroyed within dm_dp_mst_connector_destroy. connector
+	 * hdcp perperties, like type, undesired, desired, enabled,
+	 * will be lost. So, save hdcp properties into hdcp_work within
+	 * amdgpu_dm_atomic_commit_tail. if the same display is
+	 * plugged back with same display index, its hdcp properties
+	 * will be retrieved from hdcp_work within dm_dp_mst_get_modes
+	 */
+	/* un-desired, desired, enabled */
+	unsigned int content_protection[AMDGPU_DM_MAX_DISPLAY_INDEX];
+	/* hdcp1.x, hdcp2.x */
+	unsigned int hdcp_content_type[AMDGPU_DM_MAX_DISPLAY_INDEX];
+
 	uint8_t max_link;
 
 	uint8_t *srm;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c
@@ -421,7 +421,6 @@
 		struct dc_link *link)
 {
 	struct amdgpu_dm_connector *aconnector = link->priv;
-	uint8_t i;
 
 	if (!aconnector) {
 		DRM_ERROR("Failed to find connector for link!");
@@ -433,22 +432,7 @@
 
 	if (aconnector->mst_mgr.mst_state == true) {
 		drm_dp_mst_topology_mgr_set_mst(&aconnector->mst_mgr, false);
-
-		for (i = 0; i < MAX_SINKS_PER_LINK; i++) {
-			if (link->remote_sinks[i] == NULL)
-				continue;
-
-			if (link->remote_sinks[i]->sink_signal ==
-			    SIGNAL_TYPE_DISPLAY_PORT_MST) {
-				dc_link_remove_remote_sink(link, link->remote_sinks[i]);
-
-				if (aconnector->dc_sink) {
-					dc_sink_release(aconnector->dc_sink);
-					aconnector->dc_sink = NULL;
-					aconnector->dc_link->cur_link_settings.lane_count = 0;
-				}
-			}
-		}
+		link->cur_link_settings.lane_count = 0;
 	}
 }
 
@@ -648,8 +632,21 @@
 		struct aux_payload *payload,
 		enum aux_return_code_type *operation_result)
 {
-	return amdgpu_dm_process_dmub_aux_transfer_sync(ctx, link->link_index, payload, operation_result);
+	return amdgpu_dm_process_dmub_aux_transfer_sync(true, ctx,
+			link->link_index, (void *)payload,
+			(void *)operation_result);
 }
+
+int dm_helpers_dmub_set_config_sync(struct dc_context *ctx,
+		const struct dc_link *link,
+		struct set_config_cmd_payload *payload,
+		enum set_config_status *operation_result)
+{
+	return amdgpu_dm_process_dmub_aux_transfer_sync(false, ctx,
+			link->link_index, (void *)payload,
+			(void *)operation_result);
+}
+
 void dm_set_dcn_clocks(struct dc_context *ctx, struct dc_clocks *clks)
 {
 	/* TODO: something */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_irq.c
@@ -885,6 +885,7 @@
 	struct drm_device *dev = adev_to_drm(adev);
 	struct drm_connector *connector;
 	struct drm_connector_list_iter iter;
+	int i;
 
 	drm_connector_list_iter_begin(dev, &iter);
 	drm_for_each_connector_iter(connector, &iter) {
@@ -906,6 +907,12 @@
 		}
 	}
 	drm_connector_list_iter_end(&iter);
+
+	/* Update reference counts for HPDs */
+	for (i = DC_IRQ_SOURCE_HPD1; i <= adev->mode_info.num_hpd; i++) {
+		if (amdgpu_irq_get(adev, &adev->hpd_irq, i - DC_IRQ_SOURCE_HPD1))
+			drm_err(dev, "DM_IRQ: Failed get HPD for source=%d)!\n", i);
+	}
 }
 
 /**
@@ -921,6 +928,7 @@
 	struct drm_device *dev = adev_to_drm(adev);
 	struct drm_connector *connector;
 	struct drm_connector_list_iter iter;
+	int i;
 
 	drm_connector_list_iter_begin(dev, &iter);
 	drm_for_each_connector_iter(connector, &iter) {
@@ -937,4 +945,10 @@
 		}
 	}
 	drm_connector_list_iter_end(&iter);
+
+	/* Update reference counts for HPDs */
+	for (i = DC_IRQ_SOURCE_HPD1; i <= adev->mode_info.num_hpd; i++) {
+		if (amdgpu_irq_put(adev, &adev->hpd_irq, i - DC_IRQ_SOURCE_HPD1))
+			drm_err(dev, "DM_IRQ: Failed put HPD for source=%d!\n", i);
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
@@ -32,10 +32,16 @@
 #include "amdgpu_dm.h"
 #include "amdgpu_dm_mst_types.h"
 
+#ifdef CONFIG_DRM_AMD_DC_HDCP
+#include "amdgpu_dm_hdcp.h"
+#endif
+
 #include "dc.h"
 #include "dm_helpers.h"
 
 #include "dc_link_ddc.h"
+#include "ddc_service_types.h"
+#include "dpcd_defs.h"
 
 #include "i2caux_interface.h"
 #include "dmub_cmd.h"
@@ -53,6 +59,8 @@
 	ssize_t result = 0;
 	struct aux_payload payload;
 	enum aux_return_code_type operation_result;
+	struct amdgpu_device *adev;
+	struct ddc_service *ddc;
 
 	if (WARN_ON(msg->size > 16))
 		return -E2BIG;
@@ -69,6 +77,21 @@
 	result = dc_link_aux_transfer_raw(TO_DM_AUX(aux)->ddc_service, &payload,
 				      &operation_result);
 
+	/*
+	 * w/a on certain intel platform where hpd is unexpected to pull low during
+	 * 1st sideband message transaction by return AUX_RET_ERROR_HPD_DISCON
+	 * aux transaction is succuess in such case, therefore bypass the error
+	 */
+	ddc = TO_DM_AUX(aux)->ddc_service;
+	adev = ddc->ctx->driver_context;
+	if (adev->dm.aux_hpd_discon_quirk) {
+		if (msg->address == DP_SIDEBAND_MSG_DOWN_REQ_BASE &&
+			operation_result == AUX_RET_ERROR_HPD_DISCON) {
+			result = 0;
+			operation_result = AUX_RET_SUCCESS;
+		}
+	}
+
 	if (payload.write && result >= 0)
 		result = msg->size;
 
@@ -135,11 +158,28 @@
 static void
 amdgpu_dm_mst_connector_early_unregister(struct drm_connector *connector)
 {
-	struct amdgpu_dm_connector *amdgpu_dm_connector =
+	struct amdgpu_dm_connector *aconnector =
 		to_amdgpu_dm_connector(connector);
-	struct drm_dp_mst_port *port = amdgpu_dm_connector->port;
+	struct drm_dp_mst_port *port = aconnector->port;
+	struct amdgpu_dm_connector *root = aconnector->mst_port;
+	struct dc_link *dc_link = aconnector->dc_link;
+	struct dc_sink *dc_sink = aconnector->dc_sink;
 
 	drm_dp_mst_connector_early_unregister(connector, port);
+
+	/*
+	 * Release dc_sink for connector which its attached port is
+	 * no longer in the mst topology
+	 */
+	drm_modeset_lock(&root->mst_mgr.base.lock, NULL);
+	if (dc_sink) {
+		if (dc_link->sink_count)
+			dc_link_remove_remote_sink(dc_link, dc_sink);
+
+		dc_sink_release(dc_sink);
+		aconnector->dc_sink = NULL;
+	}
+	drm_modeset_unlock(&root->mst_mgr.base.lock);
 }
 
 static const struct drm_connector_funcs dm_dp_mst_connector_funcs = {
@@ -155,6 +195,31 @@
 };
 
 #if defined(CONFIG_DRM_AMD_DC_DCN)
+static bool needs_dsc_aux_workaround(struct dc_link *link)
+{
+	if (link->dpcd_caps.branch_dev_id == DP_BRANCH_DEVICE_ID_90CC24 &&
+	    (link->dpcd_caps.dpcd_rev.raw == DPCD_REV_14 || link->dpcd_caps.dpcd_rev.raw == DPCD_REV_12) &&
+	    link->dpcd_caps.sink_count.bits.SINK_COUNT >= 2)
+		return true;
+
+	return false;
+}
+
+bool is_synaptics_cascaded_panamera(struct dc_link *link, struct drm_dp_mst_port *port)
+{
+	u8 branch_vendor_data[4] = { 0 }; // Vendor data 0x50C ~ 0x50F
+
+	if (drm_dp_dpcd_read(port->mgr->aux, DP_BRANCH_VENDOR_SPECIFIC_START, &branch_vendor_data, 4) == 4) {
+		if (link->dpcd_caps.branch_dev_id == DP_BRANCH_DEVICE_ID_90CC24 &&
+				IS_SYNAPTICS_CASCADED_PANAMERA(link->dpcd_caps.branch_dev_name, branch_vendor_data)) {
+			DRM_INFO("Synaptics Cascaded MST hub\n");
+			return true;
+		}
+	}
+
+	return false;
+}
+
 static bool validate_dsc_caps_on_connector(struct amdgpu_dm_connector *aconnector)
 {
 	struct dc_sink *dc_sink = aconnector->dc_sink;
@@ -164,7 +229,7 @@
 	u8 *dsc_branch_dec_caps = NULL;
 
 	aconnector->dsc_aux = drm_dp_mst_dsc_aux_for_port(port);
-#if defined(CONFIG_HP_HOOK_WORKAROUND)
+
 	/*
 	 * drm_dp_mst_dsc_aux_for_port() will return NULL for certain configs
 	 * because it only check the dsc/fec caps of the "port variable" and not the dock
@@ -174,10 +239,14 @@
 	 * Workaround: explicitly check the use case above and use the mst dock's aux as dsc_aux
 	 *
 	 */
-
-	if (!aconnector->dsc_aux && !port->parent->port_parent)
+	if (!aconnector->dsc_aux && !port->parent->port_parent &&
+	    needs_dsc_aux_workaround(aconnector->dc_link))
 		aconnector->dsc_aux = &aconnector->mst_port->dm_dp_aux.aux;
-#endif
+
+	/* synaptics cascaded MST hub case */
+	if (is_synaptics_cascaded_panamera(aconnector->dc_link, port))
+		aconnector->dsc_aux = port->mgr->aux;
+
 	if (!aconnector->dsc_aux)
 		return false;
 
@@ -267,6 +336,32 @@
 		/* dc_link_add_remote_sink returns a new reference */
 		aconnector->dc_sink = dc_sink;
 
+		/* when display is unplugged from mst hub, connctor will be
+		 * destroyed within dm_dp_mst_connector_destroy. connector
+		 * hdcp perperties, like type, undesired, desired, enabled,
+		 * will be lost. So, save hdcp properties into hdcp_work within
+		 * amdgpu_dm_atomic_commit_tail. if the same display is
+		 * plugged back with same display index, its hdcp properties
+		 * will be retrieved from hdcp_work within dm_dp_mst_get_modes
+		 */
+#ifdef CONFIG_DRM_AMD_DC_HDCP
+		if (aconnector->dc_sink && connector->state) {
+			struct drm_device *dev = connector->dev;
+			struct amdgpu_device *adev = drm_to_adev(dev);
+
+			if (adev->dm.hdcp_workqueue) {
+				struct hdcp_workqueue *hdcp_work = adev->dm.hdcp_workqueue;
+				struct hdcp_workqueue *hdcp_w =
+					&hdcp_work[aconnector->dc_link->link_index];
+
+				connector->state->hdcp_content_type =
+				hdcp_w->hdcp_content_type[connector->index];
+				connector->state->content_protection =
+				hdcp_w->content_protection[connector->index];
+			}
+		}
+#endif
+
 		if (aconnector->dc_sink) {
 			amdgpu_dm_update_freesync_caps(
 					connector, aconnector->edid);
@@ -306,12 +401,59 @@
 {
 	struct amdgpu_dm_connector *aconnector = to_amdgpu_dm_connector(connector);
 	struct amdgpu_dm_connector *master = aconnector->mst_port;
+	struct drm_dp_mst_port *port = aconnector->port;
+	int connection_status;
 
 	if (drm_connector_is_unregistered(connector))
 		return connector_status_disconnected;
 
-	return drm_dp_mst_detect_port(connector, ctx, &master->mst_mgr,
-				      aconnector->port);
+	connection_status = drm_dp_mst_detect_port(connector, ctx, &master->mst_mgr,
+							aconnector->port);
+
+	if (port->pdt != DP_PEER_DEVICE_NONE && !port->dpcd_rev) {
+		uint8_t dpcd_rev;
+		int ret;
+
+		ret = drm_dp_dpcd_readb(&port->aux, DP_DP13_DPCD_REV, &dpcd_rev);
+
+		if (ret == 1) {
+			port->dpcd_rev = dpcd_rev;
+
+			/* Could be DP1.2 DP Rx case*/
+			if (!dpcd_rev) {
+				ret = drm_dp_dpcd_readb(&port->aux, DP_DPCD_REV, &dpcd_rev);
+
+				if (ret == 1)
+					port->dpcd_rev = dpcd_rev;
+			}
+
+			if (!dpcd_rev)
+				DRM_DEBUG_KMS("Can't decide DPCD revision number!");
+		}
+
+		/*
+		 * Could be legacy sink, logical port etc on DP1.2.
+		 * Will get Nack under these cases when issue remote
+		 * DPCD read.
+		 */
+		if (ret != 1)
+			DRM_DEBUG_KMS("Can't access DPCD");
+	} else if (port->pdt == DP_PEER_DEVICE_NONE) {
+		port->dpcd_rev = 0;
+	}
+
+	/*
+	 * Release dc_sink for connector which unplug event is notified by CSN msg
+	 */
+	if (connection_status == connector_status_disconnected && aconnector->dc_sink) {
+		if (aconnector->dc_link->sink_count)
+			dc_link_remove_remote_sink(aconnector->dc_link, aconnector->dc_sink);
+
+		dc_sink_release(aconnector->dc_sink);
+		aconnector->dc_sink = NULL;
+	}
+
+	return connection_status;
 }
 
 static int dm_dp_mst_atomic_check(struct drm_connector *connector,
@@ -356,7 +498,6 @@
 static void amdgpu_dm_encoder_destroy(struct drm_encoder *encoder)
 {
 	drm_encoder_cleanup(encoder);
-	kfree(encoder);
 }
 
 static const struct drm_encoder_funcs amdgpu_dm_encoder_funcs = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.h
@@ -26,6 +26,18 @@
 #ifndef __DAL_AMDGPU_DM_MST_TYPES_H__
 #define __DAL_AMDGPU_DM_MST_TYPES_H__
 
+#define DP_BRANCH_VENDOR_SPECIFIC_START 0x50C
+
+/**
+ * Panamera MST Hub detection
+ * Offset DPCD 050Eh == 0x5A indicates cascaded MST hub case
+ * Check from beginning of branch device vendor specific field (050Ch)
+ */
+#define IS_SYNAPTICS_PANAMERA(branchDevName) (((int)branchDevName[4] & 0xF0) == 0x50 ? 1 : 0)
+#define BRANCH_HW_REVISION_PANAMERA_A2 0x10
+#define SYNAPTICS_CASCADED_HUB_ID  0x5A
+#define IS_SYNAPTICS_CASCADED_PANAMERA(devName, data) ((IS_SYNAPTICS_PANAMERA(devName) && ((int)data[2] == SYNAPTICS_CASCADED_HUB_ID)) ? 1 : 0)
+
 struct amdgpu_display_manager;
 struct amdgpu_dm_connector;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_psr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_psr.c
@@ -36,10 +36,14 @@
 {
 	uint8_t dpcd_data[EDP_PSR_RECEIVER_CAP_SIZE];
 
-	if (!(link->connector_signal & SIGNAL_TYPE_EDP))
+	if (!(link->connector_signal & SIGNAL_TYPE_EDP)) {
+		link->psr_settings.psr_feature_enabled = false;
 		return;
-	if (link->type == dc_connection_none)
+	}
+	if (link->type == dc_connection_none) {
+		link->psr_settings.psr_feature_enabled = false;
 		return;
+	}
 	if (dm_helpers_dp_read_dpcd(NULL, link, DP_PSR_SUPPORT,
 					dpcd_data, sizeof(dpcd_data))) {
 		link->dpcd_caps.psr_caps.psr_version = dpcd_data[0];
@@ -74,10 +78,8 @@
 
 	link = stream->link;
 
-	psr_config.psr_version = link->dpcd_caps.psr_caps.psr_version;
-
-	if (psr_config.psr_version > 0) {
-		psr_config.psr_exit_link_training_required = 0x1;
+	if (link->psr_settings.psr_version != DC_PSR_VERSION_UNSUPPORTED) {
+		psr_config.psr_version = link->psr_settings.psr_version;
 		psr_config.psr_frame_capture_indication_req = 0;
 		psr_config.psr_rfb_setup_time = 0x37;
 		psr_config.psr_sdp_transmit_line_num_deadline = 0x20;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/amdgpu_dm/dc_fpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/amdgpu_dm/dc_fpu.c
@@ -52,7 +52,7 @@
  * This function tells if the code is already under FPU protection or not. A
  * function that works as an API for a set of FPU operations can use this
  * function for checking if the caller invoked it after DC_FP_START(). For
- * example, take a look at dcn2x.c file.
+ * example, take a look at dcn20_fpu.c file.
  */
 inline void dc_assert_fp_enabled(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/Makefile
@@ -23,12 +23,12 @@
 # Makefile for Display Core (dc) component.
 #
 
-DC_LIBS = basics bios calcs clk_mgr dce gpio irq virtual
+DC_LIBS = basics bios clk_mgr dce dml gpio irq virtual
 
 ifdef CONFIG_DRM_AMD_DC_DCN
 DC_LIBS += dcn20
 DC_LIBS += dsc
-DC_LIBS += dcn10 dml
+DC_LIBS += dcn10
 DC_LIBS += dcn21
 DC_LIBS += dcn30
 DC_LIBS += dcn301
@@ -58,7 +58,7 @@
 
 DISPLAY_CORE = dc.o  dc_stat.o dc_link.o dc_resource.o dc_hw_sequencer.o dc_sink.o \
 dc_surface.o dc_link_hwss.o dc_link_dp.o dc_link_ddc.o dc_debug.o dc_stream.o \
-dc_link_enc_cfg.o dc_link_dpcd.o
+dc_link_enc_cfg.o dc_link_dpia.o dc_link_dpcd.o
 
 ifdef CONFIG_DRM_AMD_DC_DCN
 DISPLAY_CORE += dc_vm_helper.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/bios/bios_parser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/bios/bios_parser.c
@@ -664,6 +664,9 @@
 
 	ss_table_header_include = GET_IMAGE(ATOM_ASIC_INTERNAL_SS_INFO_V3,
 		DATA_TABLES(ASIC_InternalSS_Info));
+	if (!ss_table_header_include)
+		return BP_RESULT_UNSUPPORTED;
+
 	table_size =
 		(le16_to_cpu(ss_table_header_include->sHeader.usStructureSize)
 				- sizeof(ATOM_COMMON_TABLE_HEADER))
@@ -1031,6 +1034,8 @@
 
 	header = GET_IMAGE(ATOM_ASIC_INTERNAL_SS_INFO_V2,
 		DATA_TABLES(ASIC_InternalSS_Info));
+	if (!header)
+		return result;
 
 	memset(info, 0, sizeof(struct spread_spectrum_info));
 
@@ -1104,6 +1109,8 @@
 	get_atom_data_table_revision(header, &revision);
 
 	tbl = GET_IMAGE(ATOM_SPREAD_SPECTRUM_INFO, DATA_TABLES(SS_Info));
+	if (!tbl)
+		return result;
 
 	if (1 != revision.major || 2 > revision.minor)
 		return result;
@@ -1631,6 +1638,8 @@
 
 	tbl = GET_IMAGE(ATOM_SPREAD_SPECTRUM_INFO,
 			DATA_TABLES(SS_Info));
+	if (!tbl)
+		return number;
 
 	if (1 != revision.major || 2 > revision.minor)
 		return number;
@@ -1711,6 +1720,8 @@
 
 	header_include = GET_IMAGE(ATOM_ASIC_INTERNAL_SS_INFO_V2,
 			DATA_TABLES(ASIC_InternalSS_Info));
+	if (!header_include)
+		return 0;
 
 	size = (le16_to_cpu(header_include->sHeader.usStructureSize)
 			- sizeof(ATOM_COMMON_TABLE_HEADER))
@@ -1748,6 +1759,9 @@
 
 	header_include = GET_IMAGE(ATOM_ASIC_INTERNAL_SS_INFO_V3,
 			DATA_TABLES(ASIC_InternalSS_Info));
+	if (!header_include)
+		return number;
+
 	size = (le16_to_cpu(header_include->sHeader.usStructureSize) -
 			sizeof(ATOM_COMMON_TABLE_HEADER)) /
 					sizeof(ATOM_ASIC_SS_ASSIGNMENT_V3);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c
@@ -352,6 +352,7 @@
 	uint32_t count = 0;
 	unsigned int table_index = 0;
 	bool find_valid = false;
+	struct atom_gpio_pin_assignment *pin;
 
 	if (!info)
 		return BP_RESULT_BADINPUT;
@@ -379,20 +380,17 @@
 			- sizeof(struct atom_common_table_header))
 				/ sizeof(struct atom_gpio_pin_assignment);
 
+	pin = (struct atom_gpio_pin_assignment *) header->gpio_pin;
+
 	for (table_index = 0; table_index < count; table_index++) {
-		if (((record->i2c_id & I2C_HW_CAP) == (
-		header->gpio_pin[table_index].gpio_id &
-						I2C_HW_CAP)) &&
-		((record->i2c_id & I2C_HW_ENGINE_ID_MASK)  ==
-		(header->gpio_pin[table_index].gpio_id &
-					I2C_HW_ENGINE_ID_MASK)) &&
-		((record->i2c_id & I2C_HW_LANE_MUX) ==
-		(header->gpio_pin[table_index].gpio_id &
-						I2C_HW_LANE_MUX))) {
+		if (((record->i2c_id & I2C_HW_CAP) 				== (pin->gpio_id & I2C_HW_CAP)) &&
+		    ((record->i2c_id & I2C_HW_ENGINE_ID_MASK)	== (pin->gpio_id & I2C_HW_ENGINE_ID_MASK)) &&
+		    ((record->i2c_id & I2C_HW_LANE_MUX) 		== (pin->gpio_id & I2C_HW_LANE_MUX))) {
 			/* still valid */
 			find_valid = true;
 			break;
 		}
+		pin = (struct atom_gpio_pin_assignment *)((uint8_t *)pin + sizeof(struct atom_gpio_pin_assignment));
 	}
 
 	/* If we don't find the entry that we are looking for then
@@ -408,11 +406,8 @@
 	info->i2c_slave_address = record->i2c_slave_addr;
 
 	/* TODO: check how to get register offset for en, Y, etc. */
-	info->gpio_info.clk_a_register_index =
-			le16_to_cpu(
-			header->gpio_pin[table_index].data_a_reg_index);
-	info->gpio_info.clk_a_shift =
-			header->gpio_pin[table_index].gpio_bitshift;
+	info->gpio_info.clk_a_register_index = le16_to_cpu(pin->data_a_reg_index);
+	info->gpio_info.clk_a_shift = pin->gpio_bitshift;
 
 	return BP_RESULT_OK;
 }
@@ -2308,6 +2303,7 @@
 				result = get_integrated_info_v2_1(bp, info);
 				break;
 			case 2:
+			case 3:
 				result = get_integrated_info_v2_2(bp, info);
 				break;
 			default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c
@@ -306,8 +306,7 @@
 	case FAMILY_NV:
 		if (ASICREV_IS_SIENNA_CICHLID_P(clk_mgr_base->ctx->asic_id.hw_internal_rev)) {
 			dcn3_clk_mgr_destroy(clk_mgr);
-		}
-		if (ASICREV_IS_DIMGREY_CAVEFISH_P(clk_mgr_base->ctx->asic_id.hw_internal_rev)) {
+		} else if (ASICREV_IS_DIMGREY_CAVEFISH_P(clk_mgr_base->ctx->asic_id.hw_internal_rev)) {
 			dcn3_clk_mgr_destroy(clk_mgr);
 		}
 		if (ASICREV_IS_BEIGE_GOBY_P(clk_mgr_base->ctx->asic_id.hw_internal_rev)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn21/rn_clk_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn21/rn_clk_mgr.c
@@ -489,7 +489,8 @@
 			ranges->reader_wm_sets[num_valid_sets].max_fill_clk_mhz = PP_SMU_WM_SET_RANGE_CLK_UNCONSTRAINED_MAX;
 
 			/* Modify previous watermark range to cover up to max */
-			ranges->reader_wm_sets[num_valid_sets - 1].max_fill_clk_mhz = PP_SMU_WM_SET_RANGE_CLK_UNCONSTRAINED_MAX;
+			if (num_valid_sets > 0)
+				ranges->reader_wm_sets[num_valid_sets - 1].max_fill_clk_mhz = PP_SMU_WM_SET_RANGE_CLK_UNCONSTRAINED_MAX;
 		}
 		num_valid_sets++;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr.c
@@ -437,8 +437,10 @@
 	clk_mgr_base->bw_params->clk_table.num_entries = num_levels ? num_levels : 1;
 
 	/* Refresh bounding box */
+	DC_FP_START();
 	clk_mgr_base->ctx->dc->res_pool->funcs->update_bw_bounding_box(
 			clk_mgr->base.ctx->dc, clk_mgr_base->bw_params);
+	DC_FP_END();
 }
 
 static bool dcn3_is_smu_present(struct clk_mgr *clk_mgr_base)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr_smu_msg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr_smu_msg.c
@@ -302,6 +302,9 @@
 	/* bits 8:7 for cache timer scale, bits 6:1 for cache timer delay, bit 0 = 1 for enable, = 0 for disable */
 	uint32_t param = (cache_timer_scale << 7) | (cache_timer_delay << 1) | (enable ? 1 : 0);
 
+	smu_print("SMU Set display refresh from mall: enable = %d, cache_timer_delay = %d, cache_timer_scale = %d\n",
+		enable, cache_timer_delay, cache_timer_scale);
+
 	dcn30_smu_send_msg_with_param(clk_mgr,
 			DALSMC_MSG_SetDisplayRefreshFromMall, param, NULL);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn301/vg_clk_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn301/vg_clk_mgr.c
@@ -582,32 +582,32 @@
 			.wm_inst = WM_A,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.65333,
-			.sr_exit_time_us = 5.32,
-			.sr_enter_plus_exit_time_us = 6.38,
+			.sr_exit_time_us = 13.5,
+			.sr_enter_plus_exit_time_us = 16.5,
 			.valid = true,
 		},
 		{
 			.wm_inst = WM_B,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.65333,
-			.sr_exit_time_us = 9.82,
-			.sr_enter_plus_exit_time_us = 11.196,
+			.sr_exit_time_us = 13.5,
+			.sr_enter_plus_exit_time_us = 16.5,
 			.valid = true,
 		},
 		{
 			.wm_inst = WM_C,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.65333,
-			.sr_exit_time_us = 9.89,
-			.sr_enter_plus_exit_time_us = 11.24,
+			.sr_exit_time_us = 13.5,
+			.sr_enter_plus_exit_time_us = 16.5,
 			.valid = true,
 		},
 		{
 			.wm_inst = WM_D,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.65333,
-			.sr_exit_time_us = 9.748,
-			.sr_enter_plus_exit_time_us = 11.102,
+			.sr_exit_time_us = 13.5,
+			.sr_enter_plus_exit_time_us = 16.5,
 			.valid = true,
 		},
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c
@@ -81,13 +81,18 @@
 				stream->signal == SIGNAL_TYPE_DVI_SINGLE_LINK ||
 				stream->signal == SIGNAL_TYPE_DVI_DUAL_LINK)
 			tmds_present = true;
+
+		/* Checking stream / link detection ensuring that PHY is active*/
+		if (dc_is_dp_signal(stream->signal) && !stream->dpms_off)
+			display_count++;
+
 	}
 
 	for (i = 0; i < dc->link_count; i++) {
 		const struct dc_link *link = dc->links[i];
 
 		/* abusing the fact that the dig and phy are coupled to see if the phy is enabled */
-		if (link->link_enc->funcs->is_dig_enabled &&
+		if (link->link_enc && link->link_enc->funcs->is_dig_enabled &&
 				link->link_enc->funcs->is_dig_enabled(link->link_enc))
 			display_count++;
 	}
@@ -157,6 +162,7 @@
 				union display_idle_optimization_u idle_info = { 0 };
 				idle_info.idle_info.df_request_disabled = 1;
 				idle_info.idle_info.phy_ref_clk_off = 1;
+				idle_info.idle_info.s0i2_rdy = 1;
 				dcn31_smu_set_display_idle_optimization(clk_mgr, idle_info.data);
 				/* update power state */
 				clk_mgr_base->clks.pwr_state = DCN_PWR_STATE_LOW_POWER;
@@ -323,38 +329,38 @@
 
 };
 
-static struct wm_table ddr4_wm_table = {
+static struct wm_table ddr5_wm_table = {
 	.entries = {
 		{
 			.wm_inst = WM_A,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.72,
-			.sr_exit_time_us = 6.09,
-			.sr_enter_plus_exit_time_us = 7.14,
+			.sr_exit_time_us = 9,
+			.sr_enter_plus_exit_time_us = 11,
 			.valid = true,
 		},
 		{
 			.wm_inst = WM_B,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.72,
-			.sr_exit_time_us = 10.12,
-			.sr_enter_plus_exit_time_us = 11.48,
+			.sr_exit_time_us = 9,
+			.sr_enter_plus_exit_time_us = 11,
 			.valid = true,
 		},
 		{
 			.wm_inst = WM_C,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.72,
-			.sr_exit_time_us = 10.12,
-			.sr_enter_plus_exit_time_us = 11.48,
+			.sr_exit_time_us = 9,
+			.sr_enter_plus_exit_time_us = 11,
 			.valid = true,
 		},
 		{
 			.wm_inst = WM_D,
 			.wm_type = WM_TYPE_PSTATE_CHG,
 			.pstate_latency_us = 11.72,
-			.sr_exit_time_us = 10.12,
-			.sr_enter_plus_exit_time_us = 11.48,
+			.sr_exit_time_us = 9,
+			.sr_enter_plus_exit_time_us = 11,
 			.valid = true,
 		},
 	}
@@ -682,7 +688,7 @@
 		if (ctx->dc_bios->integrated_info->memory_type == LpDdr5MemType) {
 			dcn31_bw_params.wm_table = lpddr5_wm_table;
 		} else {
-			dcn31_bw_params.wm_table = ddr4_wm_table;
+			dcn31_bw_params.wm_table = ddr5_wm_table;
 		}
 		/* Saved clocks configured at boot for debug purposes */
 		 dcn31_dump_clk_registers(&clk_mgr->base.base.boot_snapshot, &clk_mgr->base.base, &log_info);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_smu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_smu.c
@@ -119,6 +119,16 @@
 
 	result = dcn31_smu_wait_for_response(clk_mgr, 10, 200000);
 
+	if (result == VBIOSSMC_Result_Failed) {
+		if (msg_id == VBIOSSMC_MSG_TransferTableDram2Smu &&
+		    param == TABLE_WATERMARKS)
+			DC_LOG_WARNING("Watermarks table not configured properly by SMU");
+		else
+			ASSERT(0);
+		REG_WRITE(MP1_SMN_C2PMSG_91, VBIOSSMC_Result_OK);
+		return -1;
+	}
+
 	if (IS_SMU_TIMEOUT(result)) {
 		ASSERT(0);
 		dm_helpers_smu_timeout(CTX, msg_id, param, 10 * 200000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc.c
@@ -76,6 +76,8 @@
 
 #include "dc_trace.h"
 
+#include "dce/dmub_outbox.h"
+
 #define CTX \
 	dc->ctx
 
@@ -229,6 +231,25 @@
 
 	DC_LOG_DC("BIOS object table - end");
 
+	/* Create a link for each usb4 dpia port */
+	for (i = 0; i < dc->res_pool->usb4_dpia_count; i++) {
+		struct link_init_data link_init_params = {0};
+		struct dc_link *link;
+
+		link_init_params.ctx = dc->ctx;
+		link_init_params.connector_index = i;
+		link_init_params.link_index = dc->link_count;
+		link_init_params.dc = dc;
+		link_init_params.is_dpia_link = true;
+
+		link = link_create(&link_init_params);
+		if (link) {
+			dc->links[dc->link_count] = link;
+			link->dc = dc;
+			++dc->link_count;
+		}
+	}
+
 	for (i = 0; i < num_virtual_links; i++) {
 		struct dc_link *link = kzalloc(sizeof(*link), GFP_KERNEL);
 		struct encoder_init_data enc_init = {0};
@@ -276,6 +297,75 @@
 	return false;
 }
 
+/* Create additional DIG link encoder objects if fewer than the platform
+ * supports were created during link construction. This can happen if the
+ * number of physical connectors is less than the number of DIGs.
+ */
+static bool create_link_encoders(struct dc *dc)
+{
+	bool res = true;
+	unsigned int num_usb4_dpia = dc->res_pool->res_cap->num_usb4_dpia;
+	unsigned int num_dig_link_enc = dc->res_pool->res_cap->num_dig_link_enc;
+	int i;
+
+	/* A platform without USB4 DPIA endpoints has a fixed mapping between DIG
+	 * link encoders and physical display endpoints and does not require
+	 * additional link encoder objects.
+	 */
+	if (num_usb4_dpia == 0)
+		return res;
+
+	/* Create as many link encoder objects as the platform supports. DPIA
+	 * endpoints can be programmably mapped to any DIG.
+	 */
+	if (num_dig_link_enc > dc->res_pool->dig_link_enc_count) {
+		for (i = 0; i < num_dig_link_enc; i++) {
+			struct link_encoder *link_enc = dc->res_pool->link_encoders[i];
+
+			if (!link_enc && dc->res_pool->funcs->link_enc_create_minimal) {
+				link_enc = dc->res_pool->funcs->link_enc_create_minimal(dc->ctx,
+						(enum engine_id)(ENGINE_ID_DIGA + i));
+				if (link_enc) {
+					dc->res_pool->link_encoders[i] = link_enc;
+					dc->res_pool->dig_link_enc_count++;
+				} else {
+					res = false;
+				}
+			}
+		}
+	}
+
+	return res;
+}
+
+/* Destroy any additional DIG link encoder objects created by
+ * create_link_encoders().
+ * NB: Must only be called after destroy_links().
+ */
+static void destroy_link_encoders(struct dc *dc)
+{
+	unsigned int num_usb4_dpia = dc->res_pool->res_cap->num_usb4_dpia;
+	unsigned int num_dig_link_enc = dc->res_pool->res_cap->num_dig_link_enc;
+	int i;
+
+	/* A platform without USB4 DPIA endpoints has a fixed mapping between DIG
+	 * link encoders and physical display endpoints and does not require
+	 * additional link encoder objects.
+	 */
+	if (num_usb4_dpia == 0)
+		return;
+
+	for (i = 0; i < num_dig_link_enc; i++) {
+		struct link_encoder *link_enc = dc->res_pool->link_encoders[i];
+
+		if (link_enc) {
+			link_enc->funcs->destroy(&link_enc);
+			dc->res_pool->link_encoders[i] = NULL;
+			dc->res_pool->dig_link_enc_count--;
+		}
+	}
+}
+
 static struct dc_perf_trace *dc_perf_trace_create(void)
 {
 	return kzalloc(sizeof(struct dc_perf_trace), GFP_KERNEL);
@@ -709,6 +799,8 @@
 
 	destroy_links(dc);
 
+	destroy_link_encoders(dc);
+
 	if (dc->clk_mgr) {
 		dc_destroy_clk_mgr(dc->clk_mgr);
 		dc->clk_mgr = NULL;
@@ -771,6 +863,7 @@
 
 	dc_ctx->perf_trace = dc_perf_trace_create();
 	if (!dc_ctx->perf_trace) {
+		kfree(dc_ctx);
 		ASSERT_CRITICAL(false);
 		return false;
 	}
@@ -885,16 +978,20 @@
 	/* set i2c speed if not done by the respective dcnxxx__resource.c */
 	if (dc->caps.i2c_speed_in_khz_hdcp == 0)
 		dc->caps.i2c_speed_in_khz_hdcp = dc->caps.i2c_speed_in_khz;
-
+	if (dc->caps.max_optimizable_video_width == 0)
+		dc->caps.max_optimizable_video_width = 5120;
 	dc->clk_mgr = dc_clk_mgr_create(dc->ctx, dc->res_pool->pp_smu, dc->res_pool->dccg);
 	if (!dc->clk_mgr)
 		goto fail;
 #ifdef CONFIG_DRM_AMD_DC_DCN
 	dc->clk_mgr->force_smu_not_present = init_params->force_smu_not_present;
-#endif
 
-	if (dc->res_pool->funcs->update_bw_bounding_box)
+	if (dc->res_pool->funcs->update_bw_bounding_box) {
+		DC_FP_START();
 		dc->res_pool->funcs->update_bw_bounding_box(dc, dc->clk_mgr->bw_params);
+		DC_FP_END();
+	}
+#endif
 
 	/* Creation of current_state must occur after dc->dml
 	 * is initialized in dc_create_resource_pool because
@@ -908,13 +1005,16 @@
 		goto fail;
 	}
 
-	dc_resource_state_construct(dc, dc->current_state);
-
 	if (!create_links(dc, init_params->num_virtual_links))
 		goto fail;
 
-	/* Initialise DIG link encoder resource tracking variables. */
-	link_enc_cfg_init(dc, dc->current_state);
+	/* Create additional DIG link encoder objects if fewer than the platform
+	 * supports were created during link construction.
+	 */
+	if (!create_link_encoders(dc))
+		goto fail;
+
+	dc_resource_state_construct(dc, dc->current_state);
 
 	return true;
 
@@ -1019,6 +1119,9 @@
 		if (stream == NULL)
 			continue;
 
+		if (stream->apply_seamless_boot_optimization)
+			continue;
+
 		// only looking for first odm pipe
 		if (pipe->prev_odm_pipe)
 			continue;
@@ -1099,6 +1202,7 @@
 		return NULL;
 
 	if (init_params->dce_environment == DCE_ENV_VIRTUAL_HW) {
+		dc->caps.linear_pitch_alignment = 64;
 		if (!dc_construct_ctx(dc, init_params))
 			goto destruct_dc;
 	} else {
@@ -1118,6 +1222,8 @@
 
 		dc->caps.max_dp_protocol_version = DP_VERSION_1_4;
 
+		dc->caps.max_otg_num = dc->res_pool->res_cap->num_timing_generator;
+
 		if (dc->res_pool->dmcu != NULL)
 			dc->versions.dmcu_version = dc->res_pool->dmcu->dmcu_version;
 	}
@@ -1453,7 +1559,7 @@
 		if (crtc_timing->pix_clk_100hz != pix_clk_100hz)
 			return false;
 
-		if (!se->funcs->dp_get_pixel_format)
+		if (!se || !se->funcs->dp_get_pixel_format)
 			return false;
 
 		if (!se->funcs->dp_get_pixel_format(
@@ -1670,6 +1776,10 @@
 		wait_for_no_pipes_pending(dc, context);
 		/* pplib is notified if disp_num changed */
 		dc->hwss.optimize_bandwidth(dc, context);
+		/* Need to do otg sync again as otg could be out of sync due to otg
+		 * workaround applied during clock update
+		 */
+		dc_trigger_sync(dc, context);
 	}
 
 	if (dc->ctx->dce_version >= DCE_VERSION_MAX)
@@ -1783,6 +1893,11 @@
 
 	post_surface_trace(dc);
 
+	if (dc->ctx->dce_version >= DCE_VERSION_MAX)
+		TRACE_DCN_CLOCK_STATE(&context->bw_ctx.bw.dcn.clk);
+	else
+		TRACE_DCE_CLOCK_STATE(&context->bw_ctx.bw.dce);
+
 	if (is_flip_pending_in_pipes(dc, context))
 		return;
 
@@ -2039,6 +2154,7 @@
 }
 
 static enum surface_update_type get_scaling_info_update_type(
+		const struct dc *dc,
 		const struct dc_surface_update *u)
 {
 	union surface_update_flags *update_flags = &u->surface->update_flags;
@@ -2073,6 +2189,12 @@
 			update_flags->bits.clock_change = 1;
 	}
 
+	if (u->scaling_info->src_rect.width > dc->caps.max_optimizable_video_width &&
+		(u->scaling_info->clip_rect.width > u->surface->clip_rect.width ||
+		 u->scaling_info->clip_rect.height > u->surface->clip_rect.height))
+		 /* Changing clip size of a large surface may result in MPC slice count change */
+		update_flags->bits.bandwidth_change = 1;
+
 	if (u->scaling_info->src_rect.x != u->surface->src_rect.x
 			|| u->scaling_info->src_rect.y != u->surface->src_rect.y
 			|| u->scaling_info->clip_rect.x != u->surface->clip_rect.x
@@ -2100,9 +2222,6 @@
 	enum surface_update_type overall_type = UPDATE_TYPE_FAST;
 	union surface_update_flags *update_flags = &u->surface->update_flags;
 
-	if (u->flip_addr)
-		update_flags->bits.addr_update = 1;
-
 	if (!is_surface_in_context(context, u->surface) || u->surface->force_full_update) {
 		update_flags->raw = 0xFFFFFFFF;
 		return UPDATE_TYPE_FULL;
@@ -2113,7 +2232,7 @@
 	type = get_plane_info_update_type(u);
 	elevate_update_type(&overall_type, type);
 
-	type = get_scaling_info_update_type(u);
+	type = get_scaling_info_update_type(dc, u);
 	elevate_update_type(&overall_type, type);
 
 	if (u->flip_addr)
@@ -2452,11 +2571,8 @@
 	if (update->abm_level)
 		stream->abm_level = *update->abm_level;
 
-	if (update->periodic_interrupt0)
-		stream->periodic_interrupt0 = *update->periodic_interrupt0;
-
-	if (update->periodic_interrupt1)
-		stream->periodic_interrupt1 = *update->periodic_interrupt1;
+	if (update->periodic_interrupt)
+		stream->periodic_interrupt = *update->periodic_interrupt;
 
 	if (update->gamut_remap)
 		stream->gamut_remap_matrix = *update->gamut_remap;
@@ -2526,6 +2642,137 @@
 	}
 }
 
+void dc_reset_state(struct dc *dc, struct dc_state *context)
+{
+	dc_resource_state_destruct(context);
+
+	/* clear the structure, but don't reset the reference count */
+	memset(context, 0, offsetof(struct dc_state, refcount));
+
+	init_state(dc, context);
+}
+
+static bool update_planes_and_stream_state(struct dc *dc,
+		struct dc_surface_update *srf_updates, int surface_count,
+		struct dc_stream_state *stream,
+		struct dc_stream_update *stream_update,
+		enum surface_update_type *new_update_type,
+		struct dc_state **new_context)
+{
+	struct dc_state *context;
+	int i, j;
+	enum surface_update_type update_type;
+	const struct dc_stream_status *stream_status;
+	struct dc_context *dc_ctx = dc->ctx;
+
+	stream_status = dc_stream_get_status(stream);
+
+	if (!stream_status) {
+		if (surface_count) /* Only an error condition if surf_count non-zero*/
+			ASSERT(false);
+
+		return false; /* Cannot commit surface to stream that is not committed */
+	}
+
+	context = dc->current_state;
+
+	update_type = dc_check_update_surfaces_for_stream(
+			dc, srf_updates, surface_count, stream_update, stream_status);
+
+	/* update current stream with the new updates */
+	copy_stream_update_to_stream(dc, context, stream, stream_update);
+
+	/* do not perform surface update if surface has invalid dimensions
+	 * (all zero) and no scaling_info is provided
+	 */
+	if (surface_count > 0) {
+		for (i = 0; i < surface_count; i++) {
+			if ((srf_updates[i].surface->src_rect.width == 0 ||
+				 srf_updates[i].surface->src_rect.height == 0 ||
+				 srf_updates[i].surface->dst_rect.width == 0 ||
+				 srf_updates[i].surface->dst_rect.height == 0) &&
+				(!srf_updates[i].scaling_info ||
+				  srf_updates[i].scaling_info->src_rect.width == 0 ||
+				  srf_updates[i].scaling_info->src_rect.height == 0 ||
+				  srf_updates[i].scaling_info->dst_rect.width == 0 ||
+				  srf_updates[i].scaling_info->dst_rect.height == 0)) {
+				DC_ERROR("Invalid src/dst rects in surface update!\n");
+				return false;
+			}
+		}
+	}
+
+	if (update_type >= update_surface_trace_level)
+		update_surface_trace(dc, srf_updates, surface_count);
+
+	if (update_type >= UPDATE_TYPE_FULL) {
+		struct dc_plane_state *new_planes[MAX_SURFACES] = {0};
+
+		for (i = 0; i < surface_count; i++)
+			new_planes[i] = srf_updates[i].surface;
+
+		/* initialize scratch memory for building context */
+		context = dc_create_state(dc);
+		if (context == NULL) {
+			DC_ERROR("Failed to allocate new validate context!\n");
+			return false;
+		}
+
+		dc_resource_state_copy_construct(
+				dc->current_state, context);
+
+		/*remove old surfaces from context */
+		if (!dc_rem_all_planes_for_stream(dc, stream, context)) {
+
+			BREAK_TO_DEBUGGER();
+			goto fail;
+		}
+
+		/* add surface to context */
+		if (!dc_add_all_planes_for_stream(dc, stream, new_planes, surface_count, context)) {
+
+			BREAK_TO_DEBUGGER();
+			goto fail;
+		}
+	}
+
+	/* save update parameters into surface */
+	for (i = 0; i < surface_count; i++) {
+		struct dc_plane_state *surface = srf_updates[i].surface;
+
+		copy_surface_update_to_plane(surface, &srf_updates[i]);
+
+		if (update_type >= UPDATE_TYPE_MED) {
+			for (j = 0; j < dc->res_pool->pipe_count; j++) {
+				struct pipe_ctx *pipe_ctx = &context->res_ctx.pipe_ctx[j];
+
+				if (pipe_ctx->plane_state != surface)
+					continue;
+
+				resource_build_scaling_params(pipe_ctx);
+			}
+		}
+	}
+
+	if (update_type == UPDATE_TYPE_FULL) {
+		if (!dc->res_pool->funcs->validate_bandwidth(dc, context, false)) {
+			BREAK_TO_DEBUGGER();
+			goto fail;
+		}
+	}
+
+	*new_context = context;
+	*new_update_type = update_type;
+
+	return true;
+
+fail:
+	dc_release_state(context);
+
+	return false;
+
+}
+
 static void commit_planes_do_stream_update(struct dc *dc,
 		struct dc_stream_state *stream,
 		struct dc_stream_update *stream_update,
@@ -2540,13 +2787,8 @@
 
 		if (!pipe_ctx->top_pipe &&  !pipe_ctx->prev_odm_pipe && pipe_ctx->stream == stream) {
 
-			if (stream_update->periodic_interrupt0 &&
-					dc->hwss.setup_periodic_interrupt)
-				dc->hwss.setup_periodic_interrupt(dc, pipe_ctx, VLINE0);
-
-			if (stream_update->periodic_interrupt1 &&
-					dc->hwss.setup_periodic_interrupt)
-				dc->hwss.setup_periodic_interrupt(dc, pipe_ctx, VLINE1);
+			if (stream_update->periodic_interrupt && dc->hwss.setup_periodic_interrupt)
+				dc->hwss.setup_periodic_interrupt(dc, pipe_ctx);
 
 			if ((stream_update->hdr_static_metadata && !stream->use_dynamic_meta) ||
 					stream_update->vrr_infopacket ||
@@ -2703,7 +2945,8 @@
 #endif
 
 	if ((update_type != UPDATE_TYPE_FAST) && stream->update_flags.bits.dsc_changed)
-		if (top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
+		if (top_pipe_to_program &&
+			top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
 			if (should_use_dmub_lock(stream->link)) {
 				union dmub_hw_lock_flags hw_locks = { 0 };
 				struct dmub_hw_lock_inst_flags inst_flags = { 0 };
@@ -2879,7 +3122,8 @@
 		dc->hwss.pipe_control_lock(dc, top_pipe_to_program, false);
 
 	if ((update_type != UPDATE_TYPE_FAST) && stream->update_flags.bits.dsc_changed)
-		if (top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
+		if (top_pipe_to_program &&
+		    top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
 			top_pipe_to_program->stream_res.tg->funcs->wait_for_state(
 					top_pipe_to_program->stream_res.tg,
 					CRTC_STATE_VACTIVE);
@@ -2927,6 +3171,152 @@
 	}
 }
 
+static bool commit_minimal_transition_state(struct dc *dc,
+		struct dc_state *transition_base_context)
+{
+	struct dc_state *transition_context = dc_create_state(dc);
+	enum pipe_split_policy tmp_policy;
+	enum dc_status ret = DC_ERROR_UNEXPECTED;
+	unsigned int i, j;
+
+	if (!transition_context)
+		return false;
+
+	tmp_policy = dc->debug.pipe_split_policy;
+	dc->debug.pipe_split_policy = MPC_SPLIT_AVOID;
+
+	dc_resource_state_copy_construct(transition_base_context, transition_context);
+
+	//commit minimal state
+	if (dc->res_pool->funcs->validate_bandwidth(dc, transition_context, false)) {
+		for (i = 0; i < transition_context->stream_count; i++) {
+			struct dc_stream_status *stream_status = &transition_context->stream_status[i];
+
+			for (j = 0; j < stream_status->plane_count; j++) {
+				struct dc_plane_state *plane_state = stream_status->plane_states[j];
+
+				/* force vsync flip when reconfiguring pipes to prevent underflow
+				 * and corruption
+				 */
+				plane_state->flip_immediate = false;
+			}
+		}
+
+		ret = dc_commit_state_no_check(dc, transition_context);
+	}
+
+	//always release as dc_commit_state_no_check retains in good case
+	dc_release_state(transition_context);
+
+	//restore previous pipe split policy
+	dc->debug.pipe_split_policy = tmp_policy;
+
+	if (ret != DC_OK) {
+		//this should never happen
+		BREAK_TO_DEBUGGER();
+		return false;
+	}
+
+	//force full surface update
+	for (i = 0; i < dc->current_state->stream_count; i++) {
+		for (j = 0; j < dc->current_state->stream_status[i].plane_count; j++) {
+			dc->current_state->stream_status[i].plane_states[j]->update_flags.raw = 0xFFFFFFFF;
+		}
+	}
+
+	return true;
+}
+
+bool dc_update_planes_and_stream(struct dc *dc,
+		struct dc_surface_update *srf_updates, int surface_count,
+		struct dc_stream_state *stream,
+		struct dc_stream_update *stream_update)
+{
+	struct dc_state *context;
+	enum surface_update_type update_type;
+	int i;
+
+	/* In cases where MPO and split or ODM are used transitions can
+	 * cause underflow. Apply stream configuration with minimal pipe
+	 * split first to avoid unsupported transitions for active pipes.
+	 */
+	bool force_minimal_pipe_splitting = false;
+	bool is_plane_addition = false;
+
+	struct dc_stream_status *cur_stream_status = stream_get_status(dc->current_state, stream);
+
+	if (cur_stream_status &&
+			dc->current_state->stream_count > 0 &&
+			dc->debug.pipe_split_policy != MPC_SPLIT_AVOID) {
+		/* determine if minimal transition is required */
+		if (cur_stream_status->plane_count > surface_count) {
+			force_minimal_pipe_splitting = true;
+		} else if (cur_stream_status->plane_count < surface_count) {
+			force_minimal_pipe_splitting = true;
+			is_plane_addition = true;
+		}
+	}
+
+	/* on plane addition, minimal state is the current one */
+	if (force_minimal_pipe_splitting && is_plane_addition &&
+		!commit_minimal_transition_state(dc, dc->current_state))
+				return false;
+
+	if (!update_planes_and_stream_state(
+			dc,
+			srf_updates,
+			surface_count,
+			stream,
+			stream_update,
+			&update_type,
+			&context))
+		return false;
+
+	/* on plane addition, minimal state is the new one */
+	if (force_minimal_pipe_splitting && !is_plane_addition) {
+		if (!commit_minimal_transition_state(dc, context)) {
+			dc_release_state(context);
+			return false;
+		}
+
+		update_type = UPDATE_TYPE_FULL;
+	}
+
+	commit_planes_for_stream(
+			dc,
+			srf_updates,
+			surface_count,
+			stream,
+			stream_update,
+			update_type,
+			context);
+
+	if (dc->current_state != context) {
+
+		/* Since memory free requires elevated IRQL, an interrupt
+		 * request is generated by mem free. If this happens
+		 * between freeing and reassigning the context, our vsync
+		 * interrupt will call into dc and cause a memory
+		 * corruption BSOD. Hence, we first reassign the context,
+		 * then free the old context.
+		 */
+
+		struct dc_state *old = dc->current_state;
+
+		dc->current_state = context;
+		dc_release_state(old);
+
+		// clear any forced full updates
+		for (i = 0; i < dc->res_pool->pipe_count; i++) {
+			struct pipe_ctx *pipe_ctx = &context->res_ctx.pipe_ctx[i];
+
+			if (pipe_ctx->plane_state && pipe_ctx->stream == stream)
+				pipe_ctx->plane_state->force_full_update = false;
+		}
+	}
+	return true;
+}
+
 void dc_commit_updates_for_stream(struct dc *dc,
 		struct dc_surface_update *srf_updates,
 		int surface_count,
@@ -2968,6 +3358,14 @@
 			if (new_pipe->plane_state && new_pipe->plane_state != old_pipe->plane_state)
 				new_pipe->plane_state->force_full_update = true;
 		}
+	} else if (update_type == UPDATE_TYPE_FAST && dc_ctx->dce_version >= DCE_VERSION_MAX) {
+		/*
+		 * Previous frame finished and HW is ready for optimization.
+		 *
+		 * Only relevant for DCN behavior where we can guarantee the optimization
+		 * is safe to apply - retain the legacy behavior for DCE.
+		 */
+		dc_post_update_surfaces_to_stream(dc);
 	}
 
 
@@ -3024,14 +3422,11 @@
 				pipe_ctx->plane_state->force_full_update = false;
 		}
 	}
-	/*let's use current_state to update watermark etc*/
-	if (update_type >= UPDATE_TYPE_FULL) {
-		dc_post_update_surfaces_to_stream(dc);
 
-		if (dc_ctx->dce_version >= DCE_VERSION_MAX)
-			TRACE_DCN_CLOCK_STATE(&context->bw_ctx.bw.dcn.clk);
-		else
-			TRACE_DCE_CLOCK_STATE(&context->bw_ctx.bw.dce);
+	/* Legacy optimization path for DCE. */
+	if (update_type >= UPDATE_TYPE_FULL && dc_ctx->dce_version < DCE_VERSION_MAX) {
+		dc_post_update_surfaces_to_stream(dc);
+		TRACE_DCE_CLOCK_STATE(&context->bw_ctx.bw.dce);
 	}
 
 	return;
@@ -3371,7 +3766,8 @@
 	if (allow == dc->idle_optimizations_allowed)
 		return;
 
-	if (dc->hwss.apply_idle_power_optimizations && dc->hwss.apply_idle_power_optimizations(dc, allow))
+	if (dc->hwss.apply_idle_power_optimizations && dc->clk_mgr != NULL &&
+	    dc->hwss.apply_idle_power_optimizations(dc, allow))
 		dc->idle_optimizations_allowed = allow;
 }
 
@@ -3424,20 +3820,78 @@
 }
 #endif
 
-/**
- * dc_enable_dmub_notifications - Returns whether dmub notification can be enabled
- * @dc: dc structure
+/*
+ *****************************************************************************
+ * Function: dc_is_dmub_outbox_supported -
+ * 
+ * @brief 
+ *      Checks whether DMUB FW supports outbox notifications, if supported
+ *		DM should register outbox interrupt prior to actually enabling interrupts
+ *		via dc_enable_dmub_outbox
+ *
+ *  @param
+ *		[in] dc: dc structure
  *
- * Returns: True to enable dmub notifications, False otherwise
+ *  @return
+ *		True if DMUB FW supports outbox notifications, False otherwise
+ *****************************************************************************
  */
-bool dc_enable_dmub_notifications(struct dc *dc)
+bool dc_is_dmub_outbox_supported(struct dc *dc)
 {
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+	/* YELLOW_CARP B0 USB4 DPIA needs dmub notifications for interrupts */
+	if (dc->ctx->asic_id.chip_family == FAMILY_YELLOW_CARP &&
+	    dc->ctx->asic_id.hw_internal_rev == YELLOW_CARP_B0)
+		return true;
+#endif
 	/* dmub aux needs dmub notifications to be enabled */
 	return dc->debug.enable_dmub_aux_for_legacy_ddc;
 }
 
 /**
  * dc_process_dmub_aux_transfer_async - Submits aux command to dmub via inbox message
+ *  Function: dc_enable_dmub_notifications
+ *
+ *  @brief
+ *		Calls dc_is_dmub_outbox_supported to check if dmub fw supports outbox
+ *		notifications. All DMs shall switch to dc_is_dmub_outbox_supported.
+ *		This API shall be removed after switching.
+ *
+ *  @param
+ *		[in] dc: dc structure
+ *
+ *  @return
+ *		True if DMUB FW supports outbox notifications, False otherwise
+ *****************************************************************************
+ */
+bool dc_enable_dmub_notifications(struct dc *dc)
+{
+	return dc_is_dmub_outbox_supported(dc);
+}
+
+/**
+ *****************************************************************************
+ *  Function: dc_enable_dmub_outbox
+ *
+ *  @brief
+ *		Enables DMUB unsolicited notifications to x86 via outbox
+ *
+ *  @param
+ *		[in] dc: dc structure
+ *
+ *  @return
+ *		None
+ *****************************************************************************
+ */
+void dc_enable_dmub_outbox(struct dc *dc)
+{
+	struct dc_context *dc_ctx = dc->ctx;
+
+	dmub_enable_outbox_notification(dc_ctx->dmub_srv);
+}
+
+/**
+ *****************************************************************************
  *                                      Sets port index appropriately for legacy DDC
  * @dc: dc structure
  * @link_index: link index
@@ -3457,7 +3911,12 @@
 
 	cmd.dp_aux_access.header.type = DMUB_CMD__DP_AUX_ACCESS;
 	cmd.dp_aux_access.header.payload_bytes = 0;
-	cmd.dp_aux_access.aux_control.type = AUX_CHANNEL_LEGACY_DDC;
+	/* For dpia, ddc_pin is set to NULL */
+	if (!dc->links[link_index]->ddc->ddc_pin)
+		cmd.dp_aux_access.aux_control.type = AUX_CHANNEL_DPIA;
+	else
+		cmd.dp_aux_access.aux_control.type = AUX_CHANNEL_LEGACY_DDC;
+
 	cmd.dp_aux_access.aux_control.instance = dc->links[link_index]->ddc_hw_inst;
 	cmd.dp_aux_access.aux_control.sw_crc_enabled = 0;
 	cmd.dp_aux_access.aux_control.timeout = 0;
@@ -3501,6 +3960,130 @@
 	return true;
 }
 
+uint8_t get_link_index_from_dpia_port_index(const struct dc *dc,
+					    uint8_t dpia_port_index)
+{
+	uint8_t index, link_index = 0xFF;
+
+	for (index = 0; index < dc->link_count; index++) {
+		/* ddc_hw_inst has dpia port index for dpia links
+		 * and ddc instance for legacy links
+		 */
+		if (!dc->links[index]->ddc->ddc_pin) {
+			if (dc->links[index]->ddc_hw_inst == dpia_port_index) {
+				link_index = index;
+				break;
+			}
+		}
+	}
+	ASSERT(link_index != 0xFF);
+	return link_index;
+}
+
+/**
+ *****************************************************************************
+ *  Function: dc_process_dmub_set_config_async
+ *
+ *  @brief
+ *		Submits set_config command to dmub via inbox message
+ *
+ *  @param
+ *		[in] dc: dc structure
+ *		[in] link_index: link index
+ *		[in] payload: aux payload
+ *		[out] notify: set_config immediate reply
+ *
+ *  @return
+ *		True if successful, False if failure
+ *****************************************************************************
+ */
+bool dc_process_dmub_set_config_async(struct dc *dc,
+				uint32_t link_index,
+				struct set_config_cmd_payload *payload,
+				struct dmub_notification *notify)
+{
+	union dmub_rb_cmd cmd = {0};
+	struct dc_dmub_srv *dmub_srv = dc->ctx->dmub_srv;
+	bool is_cmd_complete = true;
+
+	/* prepare SET_CONFIG command */
+	cmd.set_config_access.header.type = DMUB_CMD__DPIA;
+	cmd.set_config_access.header.sub_type = DMUB_CMD__DPIA_SET_CONFIG_ACCESS;
+
+	cmd.set_config_access.set_config_control.instance = dc->links[link_index]->ddc_hw_inst;
+	cmd.set_config_access.set_config_control.cmd_pkt.msg_type = payload->msg_type;
+	cmd.set_config_access.set_config_control.cmd_pkt.msg_data = payload->msg_data;
+
+	if (!dc_dmub_srv_cmd_with_reply_data(dmub_srv, &cmd)) {
+		/* command is not processed by dmub */
+		notify->sc_status = SET_CONFIG_UNKNOWN_ERROR;
+		return is_cmd_complete;
+	}
+
+	/* command processed by dmub, if ret_status is 1, it is completed instantly */
+	if (cmd.set_config_access.header.ret_status == 1)
+		notify->sc_status = cmd.set_config_access.set_config_control.immed_status;
+	else
+		/* cmd pending, will receive notification via outbox */
+		is_cmd_complete = false;
+
+	return is_cmd_complete;
+}
+
+/**
+ *****************************************************************************
+ *  Function: dc_process_dmub_set_mst_slots
+ *
+ *  @brief
+ *		Submits mst slot allocation command to dmub via inbox message
+ *
+ *  @param
+ *		[in] dc: dc structure
+ *		[in] link_index: link index
+ *		[in] mst_alloc_slots: mst slots to be allotted
+ *		[out] mst_slots_in_use: mst slots in use returned in failure case
+ *
+ *	@return
+ *		DC_OK if successful, DC_ERROR if failure
+ *****************************************************************************
+ */
+enum dc_status dc_process_dmub_set_mst_slots(const struct dc *dc,
+				uint32_t link_index,
+				uint8_t mst_alloc_slots,
+				uint8_t *mst_slots_in_use)
+{
+	union dmub_rb_cmd cmd = {0};
+	struct dc_dmub_srv *dmub_srv = dc->ctx->dmub_srv;
+
+	/* prepare MST_ALLOC_SLOTS command */
+	cmd.set_mst_alloc_slots.header.type = DMUB_CMD__DPIA;
+	cmd.set_mst_alloc_slots.header.sub_type = DMUB_CMD__DPIA_MST_ALLOC_SLOTS;
+
+	cmd.set_mst_alloc_slots.mst_slots_control.instance = dc->links[link_index]->ddc_hw_inst;
+	cmd.set_mst_alloc_slots.mst_slots_control.mst_alloc_slots = mst_alloc_slots;
+
+	if (!dc_dmub_srv_cmd_with_reply_data(dmub_srv, &cmd))
+		/* command is not processed by dmub */
+		return DC_ERROR_UNEXPECTED;
+
+	/* command processed by dmub, if ret_status is 1 */
+	if (cmd.set_config_access.header.ret_status != 1)
+		/* command processing error */
+		return DC_ERROR_UNEXPECTED;
+
+	/* command processed and we have a status of 2, mst not enabled in dpia */
+	if (cmd.set_mst_alloc_slots.mst_slots_control.immed_status == 2)
+		return DC_FAIL_UNSUPPORTED_1;
+
+	/* previously configured mst alloc and used slots did not match */
+	if (cmd.set_mst_alloc_slots.mst_slots_control.immed_status == 3) {
+		*mst_slots_in_use = cmd.set_mst_alloc_slots.mst_slots_control.mst_slots_in_use;
+		return DC_NOT_SUPPORTED;
+	}
+
+	return DC_OK;
+}
+
 /**
  * dc_disable_accelerated_mode - disable accelerated mode
  * @dc: dc structure
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_hw_sequencer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_hw_sequencer.c
@@ -92,8 +92,8 @@
 		{ 0xE00, 0xF349, 0xFEB7, 0x1000, 0x6CE, 0x16E3,
 				0x24F, 0x200, 0xFCCB, 0xF535, 0xE00, 0x1000} },
 	{ COLOR_SPACE_YCBCR2020_TYPE,
-		{ 0x1000, 0xF149, 0xFEB7, 0x0000, 0x0868, 0x15B2,
-				0x01E6, 0x0000, 0xFB88, 0xF478, 0x1000, 0x0000} },
+		{ 0x1000, 0xF149, 0xFEB7, 0x1004, 0x0868, 0x15B2,
+				0x01E6, 0x201, 0xFB88, 0xF478, 0x1000, 0x1004} },
 	{ COLOR_SPACE_YCBCR709_BLACK_TYPE,
 		{ 0x0000, 0x0000, 0x0000, 0x1000, 0x0000, 0x0000,
 				0x0000, 0x0200, 0x0000, 0x0000, 0x0000, 0x1000} },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link.c
@@ -725,6 +725,18 @@
 			dal_ddc_service_set_transaction_type(link->ddc,
 							     sink_caps->transaction_type);
 
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+			/* Apply work around for tunneled MST on certain USB4 docks. Always use DSC if dock
+			 * reports DSC support.
+			 */
+			if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA &&
+					link->type == dc_connection_mst_branch &&
+					link->dpcd_caps.branch_dev_id == DP_BRANCH_DEVICE_ID_90CC24 &&
+					link->dpcd_caps.dsc_caps.dsc_basic_caps.fields.dsc_support.DSC_SUPPORT &&
+					!link->dc->debug.dpia_debug.bits.disable_mst_dsc_work_around)
+				link->wa_flags.dpia_mst_dsc_always_on = true;
+#endif
+
 #if defined(CONFIG_DRM_AMD_DC_HDCP)
 			/* In case of fallback to SST when topology discovery below fails
 			 * HDCP caps will be querried again later by the upper layer (caller
@@ -1165,6 +1177,10 @@
 			LINK_INFO("link=%d, mst branch is now Disconnected\n",
 				  link->link_index);
 
+			/* Disable work around which keeps DSC on for tunneled MST on certain USB4 docks. */
+			if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA)
+				link->wa_flags.dpia_mst_dsc_always_on = false;
+
 			dm_helpers_dp_mst_stop_top_mgr(link->ctx, link);
 
 			link->mst_stream_alloc_table.stream_count = 0;
@@ -1378,8 +1394,8 @@
 	}
 }
 
-static bool dc_link_construct(struct dc_link *link,
-			      const struct link_init_data *init_params)
+static bool dc_link_construct_legacy(struct dc_link *link,
+				     const struct link_init_data *init_params)
 {
 	uint8_t i;
 	struct ddc_service_init_data ddc_service_init_data = { { 0 } };
@@ -1651,6 +1667,77 @@
 	return false;
 }
 
+static bool dc_link_construct_dpia(struct dc_link *link,
+				   const struct link_init_data *init_params)
+{
+	struct ddc_service_init_data ddc_service_init_data = { { 0 } };
+	struct dc_context *dc_ctx = init_params->ctx;
+
+	DC_LOGGER_INIT(dc_ctx->logger);
+
+	/* Initialized irq source for hpd and hpd rx */
+	link->irq_source_hpd = DC_IRQ_SOURCE_INVALID;
+	link->irq_source_hpd_rx = DC_IRQ_SOURCE_INVALID;
+	link->link_status.dpcd_caps = &link->dpcd_caps;
+
+	link->dc = init_params->dc;
+	link->ctx = dc_ctx;
+	link->link_index = init_params->link_index;
+
+	memset(&link->preferred_training_settings, 0,
+	       sizeof(struct dc_link_training_overrides));
+	memset(&link->preferred_link_setting, 0,
+	       sizeof(struct dc_link_settings));
+
+	/* Dummy Init for linkid */
+	link->link_id.type = OBJECT_TYPE_CONNECTOR;
+	link->link_id.id = CONNECTOR_ID_DISPLAY_PORT;
+	link->link_id.enum_id = ENUM_ID_1 + init_params->connector_index;
+	link->is_internal_display = false;
+	link->connector_signal = SIGNAL_TYPE_DISPLAY_PORT;
+	LINK_INFO("Connector[%d] description:signal %d\n",
+		  init_params->connector_index,
+		  link->connector_signal);
+
+	link->ep_type = DISPLAY_ENDPOINT_USB4_DPIA;
+	link->is_dig_mapping_flexible = true;
+
+	/* TODO: Initialize link : funcs->link_init */
+
+	ddc_service_init_data.ctx = link->ctx;
+	ddc_service_init_data.id = link->link_id;
+	ddc_service_init_data.link = link;
+	/* Set indicator for dpia link so that ddc won't be created */
+	ddc_service_init_data.is_dpia_link = true;
+
+	link->ddc = dal_ddc_service_create(&ddc_service_init_data);
+	if (!link->ddc) {
+		DC_ERROR("Failed to create ddc_service!\n");
+		goto ddc_create_fail;
+	}
+
+	/* Set dpia port index : 0 to number of dpia ports */
+	link->ddc_hw_inst = init_params->connector_index;
+
+	/* TODO: Create link encoder */
+
+	link->psr_settings.psr_version = DC_PSR_VERSION_UNSUPPORTED;
+
+	return true;
+
+ddc_create_fail:
+	return false;
+}
+
+static bool dc_link_construct(struct dc_link *link,
+			      const struct link_init_data *init_params)
+{
+	/* Handle dpia case */
+	if (init_params->is_dpia_link)
+		return dc_link_construct_dpia(link, init_params);
+	else
+		return dc_link_construct_legacy(link, init_params);
+}
 /*******************************************************************************
  * Public functions
  ******************************************************************************/
@@ -1665,12 +1752,6 @@
 	if (false == dc_link_construct(link, init_params))
 		goto construct_fail;
 
-	/*
-	 * Must use preferred_link_setting, not reported_link_cap or verified_link_cap,
-	 * since struct preferred_link_setting won't be reset after S3.
-	 */
-	link->preferred_link_setting.dpcd_source_device_specific_field_support = true;
-
 	return link;
 
 construct_fail:
@@ -1696,6 +1777,8 @@
 		union down_spread_ctrl old_downspread;
 		union down_spread_ctrl new_downspread;
 
+		memset(&old_downspread, 0, sizeof(old_downspread));
+
 		core_link_read_dpcd(link, DP_DOWNSPREAD_CTRL,
 				&old_downspread.raw, sizeof(old_downspread));
 
@@ -1741,6 +1824,12 @@
 	/* get link settings for video mode timing */
 	decide_link_settings(stream, &link_settings);
 
+	/* Train with fallback when enabling DPIA link. Conventional links are
+	 * trained with fallback during sink detection.
+	 */
+	if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA)
+		do_fallback = true;
+
 	if (pipe_ctx->stream->signal == SIGNAL_TYPE_EDP) {
 		/*in case it is not on*/
 		link->dc->hwss.edp_power_control(link, true);
@@ -1832,6 +1921,57 @@
 	return enable_link_dp(state, pipe_ctx);
 }
 
+void dc_link_blank_all_dp_displays(struct dc *dc)
+{
+	unsigned int i;
+	uint8_t dpcd_power_state = '\0';
+	enum dc_status status = DC_ERROR_UNEXPECTED;
+
+	for (i = 0; i < dc->link_count; i++) {
+		if ((dc->links[i]->connector_signal != SIGNAL_TYPE_DISPLAY_PORT) ||
+			(dc->links[i]->priv == NULL) || (dc->links[i]->local_sink == NULL))
+			continue;
+
+		/* DP 2.0 spec requires that we read LTTPR caps first */
+		dp_retrieve_lttpr_cap(dc->links[i]);
+		/* if any of the displays are lit up turn them off */
+		status = core_link_read_dpcd(dc->links[i], DP_SET_POWER,
+							&dpcd_power_state, sizeof(dpcd_power_state));
+
+		if (status == DC_OK && dpcd_power_state == DP_POWER_STATE_D0)
+			dc_link_blank_dp_stream(dc->links[i], true);
+	}
+
+}
+
+void dc_link_blank_dp_stream(struct dc_link *link, bool hw_init)
+{
+	unsigned int j;
+	struct dc  *dc = link->ctx->dc;
+	enum signal_type signal = link->connector_signal;
+
+	if ((signal == SIGNAL_TYPE_EDP) ||
+		(signal == SIGNAL_TYPE_DISPLAY_PORT)) {
+		if (link->ep_type == DISPLAY_ENDPOINT_PHY &&
+			link->link_enc->funcs->get_dig_frontend &&
+			link->link_enc->funcs->is_dig_enabled(link->link_enc)) {
+			unsigned int fe = link->link_enc->funcs->get_dig_frontend(link->link_enc);
+
+			if (fe != ENGINE_ID_UNKNOWN)
+				for (j = 0; j < dc->res_pool->stream_enc_count; j++) {
+					if (fe == dc->res_pool->stream_enc[j]->id) {
+						dc->res_pool->stream_enc[j]->funcs->dp_blank(link,
+									dc->res_pool->stream_enc[j]);
+						break;
+					}
+				}
+		}
+
+		if ((!link->wa_flags.dp_keep_receiver_powered) || hw_init)
+			dp_receiver_power_ctrl(link, false);
+	}
+}
+
 static bool get_ext_hdmi_settings(struct pipe_ctx *pipe_ctx,
 		enum engine_id eng_id,
 		struct ext_hdmi_settings *settings)
@@ -3032,7 +3172,7 @@
 {
 	struct dc_stream_state *stream = pipe_ctx->stream;
 	struct dc_link *link = stream->link;
-	struct link_encoder *link_encoder = link->link_enc;
+	struct link_encoder *link_encoder = NULL;
 	struct stream_encoder *stream_encoder = pipe_ctx->stream_res.stream_enc;
 	struct dp_mst_stream_allocation_table proposed_table = {0};
 	struct fixed31_32 avg_time_slots_per_mtp;
@@ -3042,6 +3182,13 @@
 	enum act_return_status ret;
 	DC_LOGGER_INIT(link->ctx->logger);
 
+	/* Link encoder may have been dynamically assigned to non-physical display endpoint. */
+	if (link->ep_type == DISPLAY_ENDPOINT_PHY)
+		link_encoder = link->link_enc;
+	else if (link->dc->res_pool->funcs->link_encs_assign)
+		link_encoder = link_enc_cfg_get_link_enc_used_by_stream(pipe_ctx->stream->ctx->dc, stream);
+	ASSERT(link_encoder);
+
 	/* enable_link_dp_mst already check link->enabled_stream_count
 	 * and stream is in link->stream[]. This is called during set mode,
 	 * stream_enc is available.
@@ -3081,6 +3228,20 @@
 
 	ASSERT(proposed_table.stream_count > 0);
 
+	if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA) {
+		static enum dc_status status;
+		uint8_t mst_alloc_slots = 0, prev_mst_slots_in_use = 0xFF;
+
+		for (i = 0; i < link->mst_stream_alloc_table.stream_count; i++)
+			mst_alloc_slots += link->mst_stream_alloc_table.stream_allocations[i].slot_count;
+
+		status = dc_process_dmub_set_mst_slots(link->dc, link->link_index,
+			mst_alloc_slots, &prev_mst_slots_in_use);
+		ASSERT(status == DC_OK);
+		DC_LOG_MST("dpia : status[%d]: alloc_slots[%d]: used_slots[%d]\n",
+				status, mst_alloc_slots, prev_mst_slots_in_use);
+	}
+
 	/* program DP source TX for payload */
 	link_encoder->funcs->update_mst_stream_allocation_table(
 		link_encoder,
@@ -3119,7 +3280,7 @@
 {
 	struct dc_stream_state *stream = pipe_ctx->stream;
 	struct dc_link *link = stream->link;
-	struct link_encoder *link_encoder = link->link_enc;
+	struct link_encoder *link_encoder = NULL;
 	struct stream_encoder *stream_encoder = pipe_ctx->stream_res.stream_enc;
 	struct dp_mst_stream_allocation_table proposed_table = {0};
 	struct fixed31_32 avg_time_slots_per_mtp = dc_fixpt_from_int(0);
@@ -3127,6 +3288,13 @@
 	bool mst_mode = (link->type == dc_connection_mst_branch);
 	DC_LOGGER_INIT(link->ctx->logger);
 
+	/* Link encoder may have been dynamically assigned to non-physical display endpoint. */
+	if (link->ep_type == DISPLAY_ENDPOINT_PHY)
+		link_encoder = link->link_enc;
+	else if (link->dc->res_pool->funcs->link_encs_assign)
+		link_encoder = link_enc_cfg_get_link_enc_used_by_stream(pipe_ctx->stream->ctx->dc, stream);
+	ASSERT(link_encoder);
+
 	/* deallocate_mst_payload is called before disable link. When mode or
 	 * disable/enable monitor, new stream is created which is not in link
 	 * stream[] yet. For this, payload is not allocated yet, so de-alloc
@@ -3175,6 +3343,20 @@
 		link->mst_stream_alloc_table.stream_allocations[i].slot_count);
 	}
 
+	if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA) {
+		enum dc_status status;
+		uint8_t mst_alloc_slots = 0, prev_mst_slots_in_use = 0xFF;
+
+		for (i = 0; i < link->mst_stream_alloc_table.stream_count; i++)
+			mst_alloc_slots += link->mst_stream_alloc_table.stream_allocations[i].slot_count;
+
+		status = dc_process_dmub_set_mst_slots(link->dc, link->link_index,
+			mst_alloc_slots, &prev_mst_slots_in_use);
+		ASSERT(status != DC_NOT_SUPPORTED);
+		DC_LOG_MST("dpia : status[%d]: alloc_slots[%d]: used_slots[%d]\n",
+				status, mst_alloc_slots, prev_mst_slots_in_use);
+	}
+
 	link_encoder->funcs->update_mst_stream_allocation_table(
 		link_encoder,
 		&link->mst_stream_alloc_table);
@@ -3198,6 +3380,10 @@
 static void update_psp_stream_config(struct pipe_ctx *pipe_ctx, bool dpms_off)
 {
 	struct cp_psp *cp_psp = &pipe_ctx->stream->ctx->cp_psp;
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+	struct link_encoder *link_enc = NULL;
+#endif
+
 	if (cp_psp && cp_psp->funcs.update_stream_config) {
 		struct cp_psp_stream_config config = {0};
 		enum dp_panel_mode panel_mode =
@@ -3209,8 +3395,18 @@
 		config.dig_be = pipe_ctx->stream->link->link_enc_hw_inst;
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 		config.stream_enc_idx = pipe_ctx->stream_res.stream_enc->id - ENGINE_ID_DIGA;
-		config.link_enc_idx = pipe_ctx->stream->link->link_enc->transmitter - TRANSMITTER_UNIPHY_A;
-		config.phy_idx = pipe_ctx->stream->link->link_enc->transmitter - TRANSMITTER_UNIPHY_A;
+		if (pipe_ctx->stream->link->ep_type == DISPLAY_ENDPOINT_PHY) {
+			link_enc = pipe_ctx->stream->link->link_enc;
+			config.phy_idx = link_enc->transmitter - TRANSMITTER_UNIPHY_A;
+		} else if (pipe_ctx->stream->link->dc->res_pool->funcs->link_encs_assign) {
+			link_enc = link_enc_cfg_get_link_enc_used_by_stream(
+					pipe_ctx->stream->ctx->dc,
+					pipe_ctx->stream);
+			config.phy_idx = 0; /* Clear phy_idx for non-physical display endpoints. */
+		}
+		ASSERT(link_enc);
+		if (link_enc)
+			config.link_enc_idx = link_enc->transmitter - TRANSMITTER_UNIPHY_A;
 #endif
 		config.dpms_off = dpms_off;
 		config.dm_stream_ctx = pipe_ctx->stream->dm_stream_context;
@@ -3228,7 +3424,9 @@
 {
 	struct dc *dc = pipe_ctx->stream->ctx->dc;
 	struct dc_stream_state *stream = pipe_ctx->stream;
+	struct dc_link *link = stream->sink->link;
 	enum dc_status status;
+	struct link_encoder *link_enc;
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 	enum otg_out_mux_dest otg_out_dest = OUT_MUX_DIO;
 #endif
@@ -3238,10 +3436,17 @@
 			dc_is_virtual_signal(pipe_ctx->stream->signal))
 		return;
 
+	if (dc->res_pool->funcs->link_encs_assign && stream->link->ep_type != DISPLAY_ENDPOINT_PHY)
+		link_enc = link_enc_cfg_get_link_enc_used_by_stream(dc, stream);
+	else
+		link_enc = stream->link->link_enc;
+	ASSERT(link_enc);
+
 	if (!dc_is_virtual_signal(pipe_ctx->stream->signal)) {
-		stream->link->link_enc->funcs->setup(
-			stream->link->link_enc,
-			pipe_ctx->stream->signal);
+		if (link_enc)
+			link_enc->funcs->setup(
+				link_enc,
+				pipe_ctx->stream->signal);
 		pipe_ctx->stream_res.stream_enc->funcs->setup_stereo_sync(
 			pipe_ctx->stream_res.stream_enc,
 			pipe_ctx->stream_res.tg->inst,
@@ -3256,6 +3461,9 @@
 			stream->use_vsc_sdp_for_colorimetry,
 			stream->link->dpcd_caps.dprx_feature.bits.SST_SPLIT_SDP_CAP);
 
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_DP_STREAM_ATTR);
+
 	if (dc_is_hdmi_tmds_signal(pipe_ctx->stream->signal))
 		pipe_ctx->stream_res.stream_enc->funcs->hdmi_set_stream_attribute(
 			pipe_ctx->stream_res.stream_enc,
@@ -3291,6 +3499,9 @@
 		resource_build_info_frame(pipe_ctx);
 		dc->hwss.update_info_frame(pipe_ctx);
 
+		if (dc_is_dp_signal(pipe_ctx->stream->signal))
+			dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_UPDATE_INFO_FRAME);
+
 		/* Do not touch link on seamless boot optimization. */
 		if (pipe_ctx->stream->apply_seamless_boot_optimization) {
 			pipe_ctx->stream->dpms_off = false;
@@ -3366,9 +3577,10 @@
 		 * from transmitter control.
 		 */
 		if (!dc_is_virtual_signal(pipe_ctx->stream->signal))
-			stream->link->link_enc->funcs->setup(
-				stream->link->link_enc,
-				pipe_ctx->stream->signal);
+			if (link_enc)
+				link_enc->funcs->setup(
+					link_enc,
+					pipe_ctx->stream->signal);
 
 		dc->hwss.enable_stream(pipe_ctx);
 
@@ -3700,14 +3912,14 @@
 	 */
 	if (link->is_dig_mapping_flexible &&
 			link->dc->res_pool->funcs->link_encs_assign) {
-		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->dc->current_state, link);
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
 		if (link_enc == NULL)
-			link_enc = link_enc_cfg_get_next_avail_link_enc(link->dc, link->dc->current_state);
+			link_enc = link_enc_cfg_get_next_avail_link_enc(link->ctx->dc);
 	} else
 		link_enc = link->link_enc;
 	ASSERT(link_enc);
 
-	return (dc_is_dp_signal(link->connector_signal) &&
+	return (dc_is_dp_signal(link->connector_signal) && link_enc &&
 			link_enc->features.fec_supported &&
 			link->dpcd_caps.fec_cap.bits.FEC_CAPABLE &&
 			!IS_FPGA_MAXIMUS_DC(link->ctx->dce_environment));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c
@@ -196,7 +196,8 @@
 	ddc_service->link = init_data->link;
 	ddc_service->ctx = init_data->ctx;
 
-	if (BP_RESULT_OK != dcb->funcs->get_i2c_info(dcb, init_data->id, &i2c_info)) {
+	if (init_data->is_dpia_link ||
+	    dcb->funcs->get_i2c_info(dcb, init_data->id, &i2c_info) != BP_RESULT_OK) {
 		ddc_service->ddc_pin = NULL;
 	} else {
 		DC_LOGGER_INIT(ddc_service->ctx->logger);
@@ -658,10 +659,12 @@
 		struct aux_payload *payload,
 		enum aux_return_code_type *operation_result)
 {
-	if (dc_enable_dmub_notifications(ddc->ctx->dc))
+	if (ddc->ctx->dc->debug.enable_dmub_aux_for_legacy_ddc ||
+	    !ddc->ddc_pin) {
 		return dce_aux_transfer_dmub_raw(ddc, payload, operation_result);
-	else
+	} else {
 		return dce_aux_transfer_raw(ddc, payload, operation_result);
+	}
 }
 
 /* dc_link_aux_transfer_with_retries() - Attempt to submit an
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c
@@ -36,6 +36,7 @@
 #include "dpcd_defs.h"
 #include "dc_dmub_srv.h"
 #include "dce/dmub_hw_lock_mgr.h"
+#include "inc/dc_link_dpia.h"
 #include "inc/link_enc_cfg.h"
 
 /*Travis*/
@@ -197,7 +198,7 @@
 	 */
 	if (link->is_dig_mapping_flexible &&
 			link->dc->res_pool->funcs->link_encs_assign)
-		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->dc->current_state, link);
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
 	else
 		link_enc = link->link_enc;
 	ASSERT(link_enc);
@@ -1306,6 +1307,12 @@
 {
 	uint32_t lane;
 
+	/* Override link settings */
+	if (link->preferred_link_setting.link_rate != LINK_RATE_UNKNOWN)
+		lt_settings->link_settings.link_rate = link->preferred_link_setting.link_rate;
+	if (link->preferred_link_setting.lane_count != LANE_COUNT_UNKNOWN)
+		lt_settings->link_settings.lane_count = link->preferred_link_setting.lane_count;
+
 	/* Override link spread */
 	if (!link->dp_ss_off && overrides->downspread != NULL)
 		lt_settings->link_settings.link_spread = *overrides->downspread ?
@@ -1432,6 +1439,13 @@
 
 		if (encoding == DP_8b_10b_ENCODING) {
 			repeater_cnt = dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt);
+
+			/* Driver does not need to train the first hop. Skip DPCD read and clear
+			 * AUX_RD_INTERVAL for DPTX-to-DPIA hop.
+			 */
+			if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA)
+				link->dpcd_caps.lttpr_caps.aux_rd_interval[--repeater_cnt] = 0;
+
 			for (repeater_id = repeater_cnt; repeater_id > 0; repeater_id--) {
 				aux_interval_address = DP_TRAINING_AUX_RD_INTERVAL_PHY_REPEATER1 +
 							((DP_REPEATER_CONFIGURATION_AND_STATUS_SIZE) * (repeater_id - 1));
@@ -1788,16 +1802,19 @@
 	/* Dynamically assigned link encoders associated with stream rather than
 	 * link.
 	 */
-	if (link->dc->res_pool->funcs->link_encs_assign)
-		link_enc = stream->link_enc;
+	if (link->is_dig_mapping_flexible && link->dc->res_pool->funcs->link_encs_assign)
+		link_enc = link_enc_cfg_get_link_enc_used_by_stream(link->ctx->dc, pipe_ctx->stream);
 	else
 		link_enc = link->link_enc;
 
 	/* We need to do this before the link training to ensure the idle pattern in SST
 	 * mode will be sent right after the link training
 	 */
-	link_enc->funcs->connect_dig_be_to_fe(link_enc,
+	if (dp_get_link_encoding_format(&current_setting) == DP_8b_10b_ENCODING) {
+		link_enc->funcs->connect_dig_be_to_fe(link_enc,
 							pipe_ctx->stream_res.stream_enc->id, true);
+		dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_CONNECT_DIG_FE_BE);
+	}
 
 	for (j = 0; j < attempts; ++j) {
 
@@ -1836,10 +1853,22 @@
 			dc_link_dp_perform_link_training_skip_aux(link, &current_setting);
 			return true;
 		} else {
-				status = dc_link_dp_perform_link_training(
-										link,
-										&current_setting,
-										skip_video_pattern);
+			/** @todo Consolidate USB4 DP and DPx.x training. */
+			if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA) {
+				status = dc_link_dpia_perform_link_training(link,
+									    &current_setting,
+									    skip_video_pattern);
+
+				/* Transmit idle pattern once training successful. */
+				if (status == LINK_TRAINING_SUCCESS)
+					dp_set_hw_test_pattern(link, DP_TEST_PATTERN_VIDEO_MODE,
+							       NULL, 0);
+			} else {
+				status = dc_link_dp_perform_link_training(link,
+									  &current_setting,
+									  skip_video_pattern);
+			}
+
 			if (status == LINK_TRAINING_SUCCESS)
 				return true;
 		}
@@ -1862,12 +1891,16 @@
 			if (type == dc_connection_none)
 				break;
 		} else if (do_fallback) {
+			uint32_t req_bw;
+			uint32_t link_bw;
+
 			decide_fallback_link_setting(*link_setting, &current_setting, status);
 			/* Fail link training if reduced link bandwidth no longer meets
 			 * stream requirements.
 			 */
-			if (dc_bandwidth_in_kbps_from_timing(&stream->timing) <
-					dc_link_bandwidth_kbps(link, &current_setting))
+			req_bw = dc_bandwidth_in_kbps_from_timing(&stream->timing);
+			link_bw = dc_link_bandwidth_kbps(link, &current_setting);
+			if (req_bw > link_bw)
 				break;
 		}
 
@@ -2022,13 +2055,27 @@
 
 bool dc_link_dp_get_max_link_enc_cap(const struct dc_link *link, struct dc_link_settings *max_link_enc_cap)
 {
+	struct link_encoder *link_enc = NULL;
+
 	if (!max_link_enc_cap) {
 		DC_LOG_ERROR("%s: Could not return max link encoder caps", __func__);
 		return false;
 	}
 
-	if (link->link_enc->funcs->get_max_link_cap) {
-		link->link_enc->funcs->get_max_link_cap(link->link_enc, max_link_enc_cap);
+	/* Links supporting dynamically assigned link encoder will be assigned next
+	 * available encoder if one not already assigned.
+	 */
+	if (link->is_dig_mapping_flexible &&
+			link->dc->res_pool->funcs->link_encs_assign) {
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
+		if (link_enc == NULL)
+			link_enc = link_enc_cfg_get_next_avail_link_enc(link->ctx->dc);
+	} else
+		link_enc = link->link_enc;
+	ASSERT(link_enc);
+
+	if (link_enc && link_enc->funcs->get_max_link_cap) {
+		link_enc->funcs->get_max_link_cap(link_enc, max_link_enc_cap);
 		return true;
 	}
 
@@ -2041,9 +2088,23 @@
 static struct dc_link_settings get_max_link_cap(struct dc_link *link)
 {
 	struct dc_link_settings max_link_cap = {0};
+	struct link_encoder *link_enc = NULL;
+
+	/* Links supporting dynamically assigned link encoder will be assigned next
+	 * available encoder if one not already assigned.
+	 */
+	if (link->is_dig_mapping_flexible &&
+			link->dc->res_pool->funcs->link_encs_assign) {
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
+		if (link_enc == NULL)
+			link_enc = link_enc_cfg_get_next_avail_link_enc(link->ctx->dc);
+	} else
+		link_enc = link->link_enc;
+	ASSERT(link_enc);
 
 	/* get max link encoder capability */
-	link->link_enc->funcs->get_max_link_cap(link->link_enc, &max_link_cap);
+	if (link_enc)
+		link_enc->funcs->get_max_link_cap(link_enc, &max_link_cap);
 
 	/* Lower link settings based on sink's link cap */
 	if (link->reported_link_cap.lane_count < max_link_cap.lane_count)
@@ -2075,7 +2136,7 @@
 	return max_link_cap;
 }
 
-enum dc_status read_hpd_rx_irq_data(
+static enum dc_status read_hpd_rx_irq_data(
 	struct dc_link *link,
 	union hpd_irq_data *irq_data)
 {
@@ -2206,7 +2267,13 @@
 	enum link_training_result status;
 	union hpd_irq_data irq_data;
 
-	if (link->dc->debug.skip_detection_link_training) {
+	/* Accept reported capabilities if link supports flexible encoder mapping or encoder already in use. */
+	if (link->dc->debug.skip_detection_link_training ||
+			link->is_dig_mapping_flexible) {
+		link->verified_link_cap = *known_limit_link_setting;
+		return true;
+	} else if (link->link_enc && link->dc->res_pool->funcs->link_encs_assign &&
+			!link_enc_cfg_is_link_enc_avail(link->ctx->dc, link->link_enc->preferred_engine)) {
 		link->verified_link_cap = *known_limit_link_setting;
 		return true;
 	}
@@ -2246,7 +2313,7 @@
 	 * PHY will sometimes be in bad state on hotplugging display from certain USB-C dongle,
 	 * so add extra cycle of enabling and disabling the PHY before first link training.
 	 */
-	if (link->link_enc->features.flags.bits.DP_IS_USB_C &&
+	if (link->link_enc && link->link_enc->features.flags.bits.DP_IS_USB_C &&
 			link->dc->debug.usbc_combo_phy_reset_wa) {
 		dp_enable_link_phy(link, link->connector_signal, dp_cs_id, cur);
 		dp_disable_link_phy(link, link->connector_signal);
@@ -2743,7 +2810,7 @@
 }
 
 /*************************Short Pulse IRQ***************************/
-static bool allow_hpd_rx_irq(const struct dc_link *link)
+bool dc_link_dp_allow_hpd_rx_irq(const struct dc_link *link)
 {
 	/*
 	 * Don't handle RX IRQ unless one of following is met:
@@ -3118,7 +3185,7 @@
 		&dpcd_pattern_type.value,
 		sizeof(dpcd_pattern_type));
 
-	channel_count = dpcd_test_mode.bits.channel_count + 1;
+	channel_count = min(dpcd_test_mode.bits.channel_count + 1, AUDIO_CHANNELS_COUNT);
 
 	// read pattern periods for requested channels when sawTooth pattern is requested
 	if (dpcd_pattern_type.value == AUDIO_TEST_PATTERN_SAWTOOTH ||
@@ -3177,7 +3244,7 @@
 	}
 }
 
-static void handle_automated_test(struct dc_link *link)
+void dc_link_dp_handle_automated_test(struct dc_link *link)
 {
 	union test_request test_request;
 	union test_response test_response;
@@ -3226,17 +3293,50 @@
 			sizeof(test_response));
 }
 
-bool dc_link_handle_hpd_rx_irq(struct dc_link *link, union hpd_irq_data *out_hpd_irq_dpcd_data, bool *out_link_loss)
+void dc_link_dp_handle_link_loss(struct dc_link *link)
+{
+	int i;
+	struct pipe_ctx *pipe_ctx;
+
+	for (i = 0; i < MAX_PIPES; i++) {
+		pipe_ctx = &link->dc->current_state->res_ctx.pipe_ctx[i];
+		if (pipe_ctx && pipe_ctx->stream && pipe_ctx->stream->link == link)
+			break;
+	}
+
+	if (pipe_ctx == NULL || pipe_ctx->stream == NULL)
+		return;
+
+	for (i = 0; i < MAX_PIPES; i++) {
+		pipe_ctx = &link->dc->current_state->res_ctx.pipe_ctx[i];
+		if (pipe_ctx && pipe_ctx->stream && !pipe_ctx->stream->dpms_off &&
+				pipe_ctx->stream->link == link && !pipe_ctx->prev_odm_pipe) {
+			core_link_disable_stream(pipe_ctx);
+		}
+	}
+
+	for (i = 0; i < MAX_PIPES; i++) {
+		pipe_ctx = &link->dc->current_state->res_ctx.pipe_ctx[i];
+		if (pipe_ctx && pipe_ctx->stream && !pipe_ctx->stream->dpms_off &&
+				pipe_ctx->stream->link == link && !pipe_ctx->prev_odm_pipe) {
+			core_link_enable_stream(link->dc->current_state, pipe_ctx);
+		}
+	}
+}
+
+bool dc_link_handle_hpd_rx_irq(struct dc_link *link, union hpd_irq_data *out_hpd_irq_dpcd_data, bool *out_link_loss,
+							bool defer_handling, bool *has_left_work)
 {
 	union hpd_irq_data hpd_irq_dpcd_data = { { { {0} } } };
 	union device_service_irq device_service_clear = { { 0 } };
 	enum dc_status result;
 	bool status = false;
-	struct pipe_ctx *pipe_ctx;
-	int i;
 
 	if (out_link_loss)
 		*out_link_loss = false;
+
+	if (has_left_work)
+		*has_left_work = false;
 	/* For use cases related to down stream connection status change,
 	 * PSR and device auto test, refer to function handle_sst_hpd_irq
 	 * in DAL2.1*/
@@ -3268,11 +3368,14 @@
 			&device_service_clear.raw,
 			sizeof(device_service_clear.raw));
 		device_service_clear.raw = 0;
-		handle_automated_test(link);
+		if (defer_handling && has_left_work)
+			*has_left_work = true;
+		else
+			dc_link_dp_handle_automated_test(link);
 		return false;
 	}
 
-	if (!allow_hpd_rx_irq(link)) {
+	if (!dc_link_dp_allow_hpd_rx_irq(link)) {
 		DC_LOG_HW_HPD_IRQ("%s: skipping HPD handling on %d\n",
 			__func__, link->link_index);
 		return false;
@@ -3286,12 +3389,18 @@
 	 * so do not handle as a normal sink status change interrupt.
 	 */
 
-	if (hpd_irq_dpcd_data.bytes.device_service_irq.bits.UP_REQ_MSG_RDY)
+	if (hpd_irq_dpcd_data.bytes.device_service_irq.bits.UP_REQ_MSG_RDY) {
+		if (defer_handling && has_left_work)
+			*has_left_work = true;
 		return true;
+	}
 
 	/* check if we have MST msg and return since we poll for it */
-	if (hpd_irq_dpcd_data.bytes.device_service_irq.bits.DOWN_REP_MSG_RDY)
+	if (hpd_irq_dpcd_data.bytes.device_service_irq.bits.DOWN_REP_MSG_RDY) {
+		if (defer_handling && has_left_work)
+			*has_left_work = true;
 		return false;
+	}
 
 	/* For now we only handle 'Downstream port status' case.
 	 * If we got sink count changed it means
@@ -3308,29 +3417,10 @@
 					sizeof(hpd_irq_dpcd_data),
 					"Status: ");
 
-		for (i = 0; i < MAX_PIPES; i++) {
-			pipe_ctx = &link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream && pipe_ctx->stream->link == link)
-				break;
-		}
-
-		if (pipe_ctx == NULL || pipe_ctx->stream == NULL)
-			return false;
-
-
-		for (i = 0; i < MAX_PIPES; i++) {
-			pipe_ctx = &link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream && !pipe_ctx->stream->dpms_off &&
-					pipe_ctx->stream->link == link && !pipe_ctx->prev_odm_pipe)
-				core_link_disable_stream(pipe_ctx);
-		}
-
-		for (i = 0; i < MAX_PIPES; i++) {
-			pipe_ctx = &link->dc->current_state->res_ctx.pipe_ctx[i];
-			if (pipe_ctx && pipe_ctx->stream && !pipe_ctx->stream->dpms_off &&
-					pipe_ctx->stream->link == link && !pipe_ctx->prev_odm_pipe)
-				core_link_enable_stream(link->dc->current_state, pipe_ctx);
-		}
+		if (defer_handling && has_left_work)
+			*has_left_work = true;
+		else
+			dc_link_dp_handle_link_loss(link);
 
 		status = false;
 		if (out_link_loss)
@@ -3639,6 +3729,12 @@
 		else
 			link->lttpr_mode = LTTPR_MODE_NON_TRANSPARENT;
 	}
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+	/* Check DP tunnel LTTPR mode debug option. */
+	if (link->ep_type == DISPLAY_ENDPOINT_USB4_DPIA &&
+	    link->dc->debug.dpia_debug.bits.force_non_lttpr)
+		link->lttpr_mode = LTTPR_MODE_NON_LTTPR;
+#endif
 
 	if (link->lttpr_mode == LTTPR_MODE_NON_TRANSPARENT || link->lttpr_mode == LTTPR_MODE_TRANSPARENT) {
 		/* By reading LTTPR capability, RX assumes that we will enable
@@ -3650,7 +3746,9 @@
 				lttpr_dpcd_data,
 				sizeof(lttpr_dpcd_data));
 		if (status != DC_OK) {
-			dm_error("%s: Read LTTPR caps data failed.\n", __func__);
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+			DC_LOG_DP2("%s: Read LTTPR caps data failed.\n", __func__);
+#endif
 			return false;
 		}
 
@@ -3678,8 +3776,17 @@
 				lttpr_dpcd_data[DP_PHY_REPEATER_EXTENDED_WAIT_TIMEOUT -
 								DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV];
 
+		/* If this chip cap is set, at least one retimer must exist in the chain
+		 * Override count to 1 if we receive a known bad count (0 or an invalid value) */
+		if (link->chip_caps & EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN &&
+				(dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt) == 0)) {
+			ASSERT(0);
+			link->dpcd_caps.lttpr_caps.phy_repeater_cnt = 0x80;
+		}
+
 		/* Attempt to train in LTTPR transparent mode if repeater count exceeds 8. */
 		is_lttpr_present = (dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt) != 0 &&
+				link->dpcd_caps.lttpr_caps.phy_repeater_cnt < 0xff &&
 				link->dpcd_caps.lttpr_caps.max_lane_count > 0 &&
 				link->dpcd_caps.lttpr_caps.max_lane_count <= 4 &&
 				link->dpcd_caps.lttpr_caps.revision.raw >= 0x14);
@@ -3728,6 +3835,8 @@
 			LINK_AUX_DEFAULT_LTTPR_TIMEOUT_PERIOD);
 
 	is_lttpr_present = dp_retrieve_lttpr_cap(link);
+	/* Read DP tunneling information. */
+	status = dpcd_get_tunneling_device_data(link);
 
 	status = core_link_read_dpcd(link, DP_SET_POWER,
 			&dpcd_power_state, sizeof(dpcd_power_state));
@@ -3913,6 +4022,26 @@
 		dp_hw_fw_revision.ieee_fw_rev,
 		sizeof(dp_hw_fw_revision.ieee_fw_rev));
 
+	/* Quirk for Apple MBP 2018 15" Retina panels: wrong DP_MAX_LINK_RATE */
+	{
+		uint8_t str_mbp_2018[] = { 101, 68, 21, 103, 98, 97 };
+		uint8_t fwrev_mbp_2018[] = { 7, 4 };
+		uint8_t fwrev_mbp_2018_vega[] = { 8, 4 };
+
+		/* We also check for the firmware revision as 16,1 models have an
+		 * identical device id and are incorrectly quirked otherwise.
+		 */
+		if ((link->dpcd_caps.sink_dev_id == 0x0010fa) &&
+		    !memcmp(link->dpcd_caps.sink_dev_id_str, str_mbp_2018,
+			     sizeof(str_mbp_2018)) &&
+		    (!memcmp(link->dpcd_caps.sink_fw_revision, fwrev_mbp_2018,
+			     sizeof(fwrev_mbp_2018)) ||
+		    !memcmp(link->dpcd_caps.sink_fw_revision, fwrev_mbp_2018_vega,
+			     sizeof(fwrev_mbp_2018_vega)))) {
+			link->reported_link_cap.link_rate = LINK_RATE_RBR2;
+		}
+	}
+
 	memset(&link->dpcd_caps.dsc_caps, '\0',
 			sizeof(link->dpcd_caps.dsc_caps));
 	memset(&link->dpcd_caps.fec_cap, '\0', sizeof(link->dpcd_caps.fec_cap));
@@ -4368,7 +4497,7 @@
 			 * MuteAudioEndpoint(pPathMode->pDisplayPath, true);
 			 */
 			/* Blank stream */
-			pipes->stream_res.stream_enc->funcs->dp_blank(pipe_ctx->stream_res.stream_enc);
+			pipes->stream_res.stream_enc->funcs->dp_blank(link, pipe_ctx->stream_res.stream_enc);
 		}
 
 		dp_set_hw_test_pattern(link, test_pattern,
@@ -4670,7 +4799,7 @@
 	 */
 	if (link->is_dig_mapping_flexible &&
 			link->dc->res_pool->funcs->link_encs_assign)
-		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->dc->current_state, link);
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
 	else
 		link_enc = link->link_enc;
 	ASSERT(link_enc);
@@ -4690,7 +4819,7 @@
 				link_enc->funcs->fec_set_ready(link_enc, true);
 				link->fec_state = dc_link_fec_ready;
 			} else {
-				link_enc->funcs->fec_set_ready(link->link_enc, false);
+				link_enc->funcs->fec_set_ready(link_enc, false);
 				link->fec_state = dc_link_fec_not_ready;
 				dm_error("dpcd write failed to set fec_ready");
 			}
@@ -4717,8 +4846,7 @@
 	 */
 	if (link->is_dig_mapping_flexible &&
 			link->dc->res_pool->funcs->link_encs_assign)
-		link_enc = link_enc_cfg_get_link_enc_used_by_link(
-				link->dc->current_state, link);
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
 	else
 		link_enc = link->link_enc;
 	ASSERT(link_enc);
@@ -4788,18 +4916,10 @@
 
 			uint8_t hblank_size = (uint8_t)link->dc->caps.min_horizontal_blanking_period;
 
-			if (link->preferred_link_setting.dpcd_source_device_specific_field_support) {
-				result_write_min_hblank = core_link_write_dpcd(link,
-					DP_SOURCE_MINIMUM_HBLANK_SUPPORTED, (uint8_t *)(&hblank_size),
-					sizeof(hblank_size));
-
-				if (result_write_min_hblank == DC_ERROR_UNEXPECTED)
-					link->preferred_link_setting.dpcd_source_device_specific_field_support = false;
-			} else {
-				DC_LOG_DC("Sink device does not support 00340h DPCD write. Skipping on purpose.\n");
-			}
+			result_write_min_hblank = core_link_write_dpcd(link,
+				DP_SOURCE_MINIMUM_HBLANK_SUPPORTED, (uint8_t *)(&hblank_size),
+				sizeof(hblank_size));
 		}
-
 		DC_TRACE_LEVEL_MESSAGE(DAL_TRACE_LEVEL_INFORMATION,
 							WPP_BIT_FLAG_DC_DETECTION_DP_CAPS,
 							"result=%u link_index=%u enum dce_version=%d DPCD=0x%04X min_hblank=%u branch_dev_id=0x%x branch_dev_name='%c%c%c%c%c%c'",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link_dpcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link_dpcd.c
@@ -199,7 +199,7 @@
 	uint32_t extended_size;
 	/* size of the remaining partitioned address space */
 	uint32_t size_left_to_read;
-	enum dc_status status;
+	enum dc_status status = DC_ERROR_UNEXPECTED;
 	/* size of the next partition to be read from */
 	uint32_t partition_size;
 	uint32_t data_index = 0;
@@ -228,7 +228,7 @@
 {
 	uint32_t partition_size;
 	uint32_t data_index = 0;
-	enum dc_status status;
+	enum dc_status status = DC_ERROR_UNEXPECTED;
 
 	while (size) {
 		partition_size = dpcd_get_next_partition_size(address, size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link_dpia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link_dpia.c
@@ -0,0 +1,953 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include "dc.h"
+#include "dc_link_dpia.h"
+#include "inc/core_status.h"
+#include "dc_link.h"
+#include "dc_link_dp.h"
+#include "dpcd_defs.h"
+#include "link_hwss.h"
+#include "inc/link_dpcd.h"
+#include "dm_helpers.h"
+#include "dmub/inc/dmub_cmd.h"
+#include "inc/link_dpcd.h"
+
+#define DC_LOGGER \
+	link->ctx->logger
+
+enum dc_status dpcd_get_tunneling_device_data(struct dc_link *link)
+{
+	enum dc_status status = DC_OK;
+	uint8_t dpcd_dp_tun_data[3] = {0};
+	uint8_t dpcd_topology_data[DPCD_USB4_TOPOLOGY_ID_LEN] = {0};
+	uint8_t i = 0;
+
+	status = core_link_read_dpcd(link,
+			DP_TUNNELING_CAPABILITIES_SUPPORT,
+			dpcd_dp_tun_data,
+			sizeof(dpcd_dp_tun_data));
+
+	status = core_link_read_dpcd(link,
+			DP_USB4_ROUTER_TOPOLOGY_ID,
+			dpcd_topology_data,
+			sizeof(dpcd_topology_data));
+
+	link->dpcd_caps.usb4_dp_tun_info.dp_tun_cap.raw =
+			dpcd_dp_tun_data[DP_TUNNELING_CAPABILITIES_SUPPORT -
+					 DP_TUNNELING_CAPABILITIES_SUPPORT];
+	link->dpcd_caps.usb4_dp_tun_info.dpia_info.raw =
+			dpcd_dp_tun_data[DP_IN_ADAPTER_INFO - DP_TUNNELING_CAPABILITIES_SUPPORT];
+	link->dpcd_caps.usb4_dp_tun_info.usb4_driver_id =
+			dpcd_dp_tun_data[DP_USB4_DRIVER_ID - DP_TUNNELING_CAPABILITIES_SUPPORT];
+
+	for (i = 0; i < DPCD_USB4_TOPOLOGY_ID_LEN; i++)
+		link->dpcd_caps.usb4_dp_tun_info.usb4_topology_id[i] = dpcd_topology_data[i];
+
+	return status;
+}
+
+/* Configure link as prescribed in link_setting; set LTTPR mode; and
+ * Initialize link training settings.
+ * Abort link training if sink unplug detected.
+ *
+ * @param link DPIA link being trained.
+ * @param[in] link_setting Lane count, link rate and downspread control.
+ * @param[out] lt_settings Link settings and drive settings (voltage swing and pre-emphasis).
+ */
+static enum link_training_result dpia_configure_link(struct dc_link *link,
+		const struct dc_link_settings *link_setting,
+		struct link_training_settings *lt_settings)
+{
+	enum dc_status status;
+	bool fec_enable;
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) configuring\n - LTTPR mode(%d)\n",
+				__func__,
+				link->link_id.enum_id - ENUM_ID_1,
+				link->lttpr_mode);
+
+	dp_decide_training_settings(link,
+		link_setting,
+		lt_settings);
+
+	status = dpcd_configure_channel_coding(link, lt_settings);
+	if (status != DC_OK && !link->hpd_status)
+		return LINK_TRAINING_ABORT;
+
+	/* Configure lttpr mode */
+	status = dpcd_configure_lttpr_mode(link, lt_settings);
+	if (status != DC_OK && !link->hpd_status)
+		return LINK_TRAINING_ABORT;
+
+	/* Set link rate, lane count and spread. */
+	status = dpcd_set_link_settings(link, lt_settings);
+	if (status != DC_OK && !link->hpd_status)
+		return LINK_TRAINING_ABORT;
+
+	if (link->preferred_training_settings.fec_enable)
+		fec_enable = *link->preferred_training_settings.fec_enable;
+	else
+		fec_enable = true;
+	status = dp_set_fec_ready(link, fec_enable);
+	if (status != DC_OK && !link->hpd_status)
+		return LINK_TRAINING_ABORT;
+
+	return LINK_TRAINING_SUCCESS;
+}
+
+static enum dc_status core_link_send_set_config(struct dc_link *link,
+	uint8_t msg_type,
+	uint8_t msg_data)
+{
+	struct set_config_cmd_payload payload;
+	enum set_config_status set_config_result = SET_CONFIG_PENDING;
+
+	/* prepare set_config payload */
+	payload.msg_type = msg_type;
+	payload.msg_data = msg_data;
+
+	if (!link->ddc->ddc_pin && !link->aux_access_disabled &&
+	    (dm_helpers_dmub_set_config_sync(link->ctx, link,
+					     &payload, &set_config_result) == -1)) {
+		return DC_ERROR_UNEXPECTED;
+	}
+
+	/* set_config should return ACK if successful */
+	return (set_config_result == SET_CONFIG_ACK_RECEIVED) ? DC_OK : DC_ERROR_UNEXPECTED;
+}
+
+/* Build SET_CONFIG message data payload for specified message type. */
+static uint8_t dpia_build_set_config_data(enum dpia_set_config_type type,
+		struct dc_link *link,
+		struct link_training_settings *lt_settings)
+{
+	union dpia_set_config_data data;
+
+	data.raw = 0;
+
+	switch (type) {
+	case DPIA_SET_CFG_SET_LINK:
+		data.set_link.mode = link->lttpr_mode == LTTPR_MODE_NON_TRANSPARENT ? 1 : 0;
+		break;
+	case DPIA_SET_CFG_SET_PHY_TEST_MODE:
+		break;
+	case DPIA_SET_CFG_SET_VSPE:
+		/* Assume all lanes have same drive settings. */
+		data.set_vspe.swing = lt_settings->lane_settings[0].VOLTAGE_SWING;
+		data.set_vspe.pre_emph = lt_settings->lane_settings[0].PRE_EMPHASIS;
+		data.set_vspe.max_swing_reached =
+			lt_settings->lane_settings[0].VOLTAGE_SWING ==
+			VOLTAGE_SWING_MAX_LEVEL ? 1 : 0;
+		data.set_vspe.max_pre_emph_reached =
+			lt_settings->lane_settings[0].PRE_EMPHASIS ==
+			PRE_EMPHASIS_MAX_LEVEL ? 1 : 0;
+		break;
+	default:
+		ASSERT(false); /* Message type not supported by helper function. */
+		break;
+	}
+
+	return data.raw;
+}
+
+/* Convert DC training pattern to DPIA training stage. */
+static enum dpia_set_config_ts convert_trng_ptn_to_trng_stg(enum dc_dp_training_pattern tps)
+{
+	enum dpia_set_config_ts ts;
+
+	switch (tps) {
+	case DP_TRAINING_PATTERN_SEQUENCE_1:
+		ts = DPIA_TS_TPS1;
+		break;
+	case DP_TRAINING_PATTERN_SEQUENCE_2:
+		ts = DPIA_TS_TPS2;
+		break;
+	case DP_TRAINING_PATTERN_SEQUENCE_3:
+		ts = DPIA_TS_TPS3;
+		break;
+	case DP_TRAINING_PATTERN_SEQUENCE_4:
+		ts = DPIA_TS_TPS4;
+		break;
+	default:
+		ASSERT(false); /* TPS not supported by helper function. */
+		break;
+	}
+
+	return ts;
+}
+
+/* Write training pattern to DPCD. */
+static enum dc_status dpcd_set_lt_pattern(struct dc_link *link,
+	enum dc_dp_training_pattern pattern,
+	uint32_t hop)
+{
+	union dpcd_training_pattern dpcd_pattern = { {0} };
+	uint32_t dpcd_tps_offset = DP_TRAINING_PATTERN_SET;
+	enum dc_status status;
+
+	if (hop != DPRX)
+		dpcd_tps_offset = DP_TRAINING_PATTERN_SET_PHY_REPEATER1 +
+			((DP_REPEATER_CONFIGURATION_AND_STATUS_SIZE) * (hop - 1));
+
+	/* DpcdAddress_TrainingPatternSet */
+	dpcd_pattern.v1_4.TRAINING_PATTERN_SET =
+		dc_dp_training_pattern_to_dpcd_training_pattern(link, pattern);
+
+	dpcd_pattern.v1_4.SCRAMBLING_DISABLE =
+		dc_dp_initialize_scrambling_data_symbols(link, pattern);
+
+	if (hop != DPRX) {
+		DC_LOG_HW_LINK_TRAINING("%s\n LTTPR Repeater ID: %d\n 0x%X pattern = %x\n",
+					__func__,
+					hop,
+					dpcd_tps_offset,
+					dpcd_pattern.v1_4.TRAINING_PATTERN_SET);
+	} else {
+		DC_LOG_HW_LINK_TRAINING("%s\n 0x%X pattern = %x\n",
+					__func__,
+					dpcd_tps_offset,
+					dpcd_pattern.v1_4.TRAINING_PATTERN_SET);
+	}
+
+	status = core_link_write_dpcd(link,
+				      dpcd_tps_offset,
+				      &dpcd_pattern.raw,
+				      sizeof(dpcd_pattern.raw));
+
+	return status;
+}
+
+/* Execute clock recovery phase of link training for specified hop in display
+ * path.in non-transparent mode:
+ * - Driver issues both DPCD and SET_CONFIG transactions.
+ * - TPS1 is transmitted for any hops downstream of DPOA.
+ * - Drive (VS/PE) only transmitted for the hop immediately downstream of DPOA.
+ * - CR for the first hop (DPTX-to-DPIA) is assumed to be successful.
+ *
+ * @param link DPIA link being trained.
+ * @param lt_settings link_setting and drive settings (voltage swing and pre-emphasis).
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static enum link_training_result dpia_training_cr_non_transparent(struct dc_link *link,
+		struct link_training_settings *lt_settings,
+		uint32_t hop)
+{
+	enum link_training_result result = LINK_TRAINING_CR_FAIL_LANE0;
+	uint8_t repeater_cnt = 0; /* Number of hops/repeaters in display path. */
+	enum dc_status status;
+	uint32_t retries_cr = 0; /* Number of consecutive attempts with same VS or PE. */
+	uint32_t retry_count = 0;
+	/* From DP spec, CR read interval is always 100us. */
+	uint32_t wait_time_microsec = TRAINING_AUX_RD_INTERVAL;
+	struct link_training_settings req_settings;
+	enum dc_lane_count lane_count = lt_settings->link_settings.lane_count;
+	union lane_status dpcd_lane_status[LANE_COUNT_DP_MAX] = { { {0} } };
+	union lane_align_status_updated dpcd_lane_status_updated = { {0} };
+	uint8_t set_cfg_data;
+	enum dpia_set_config_ts ts;
+
+	repeater_cnt = dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt);
+
+	/* Cap of LINK_TRAINING_MAX_CR_RETRY attempts at clock recovery.
+	 * Fix inherited from perform_clock_recovery_sequence() -
+	 * the DP equivalent of this function:
+	 * Required for Synaptics MST hub which can put the LT in
+	 * infinite loop by switching the VS between level 0 and level 1
+	 * continuously.
+	 */
+	while ((retries_cr < LINK_TRAINING_MAX_RETRY_COUNT) &&
+	       (retry_count < LINK_TRAINING_MAX_CR_RETRY)) {
+		/* DPTX-to-DPIA */
+		if (hop == repeater_cnt) {
+			/* Send SET_CONFIG(SET_LINK:LC,LR,LTTPR) to notify DPOA that
+			 * non-transparent link training has started.
+			 * This also enables the transmission of clk_sync packets.
+			 */
+			set_cfg_data = dpia_build_set_config_data(DPIA_SET_CFG_SET_LINK,
+					link,
+					lt_settings);
+			status = core_link_send_set_config(link,
+					DPIA_SET_CFG_SET_LINK,
+					set_cfg_data);
+			/* CR for this hop is considered successful as long as
+			 * SET_CONFIG message is acknowledged by DPOA.
+			 */
+			if (status == DC_OK)
+				result = LINK_TRAINING_SUCCESS;
+			else
+				result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		/* DPOA-to-x */
+		/* Instruct DPOA to transmit TPS1 then update DPCD. */
+		if (retry_count == 0) {
+			ts = convert_trng_ptn_to_trng_stg(lt_settings->pattern_for_cr);
+			status = core_link_send_set_config(link,
+					DPIA_SET_CFG_SET_TRAINING,
+					ts);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+			status = dpcd_set_lt_pattern(link, lt_settings->pattern_for_cr, hop);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+		}
+
+		/* Update DPOA drive settings then DPCD. DPOA does only adjusts
+		 * drive settings for hops immediately downstream.
+		 */
+		if (hop == repeater_cnt - 1) {
+			set_cfg_data = dpia_build_set_config_data(DPIA_SET_CFG_SET_VSPE,
+					link,
+					lt_settings);
+			status = core_link_send_set_config(link,
+					DPIA_SET_CFG_SET_VSPE,
+					set_cfg_data);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+		}
+		status = dpcd_set_lane_settings(link, lt_settings, hop);
+		if (status != DC_OK) {
+			result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		dp_wait_for_training_aux_rd_interval(link, wait_time_microsec);
+
+		/* Read status and adjustment requests from DPCD. */
+		status = dp_get_lane_status_and_drive_settings(link,
+				lt_settings,
+				dpcd_lane_status,
+				&dpcd_lane_status_updated,
+				&req_settings,
+				hop);
+		if (status != DC_OK) {
+			result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		/* Check if clock recovery successful. */
+		if (dp_is_cr_done(lane_count, dpcd_lane_status)) {
+			result = LINK_TRAINING_SUCCESS;
+			break;
+		}
+
+		result = dp_get_cr_failure(lane_count, dpcd_lane_status);
+
+		if (dp_is_max_vs_reached(lt_settings))
+			break;
+
+		/* Count number of attempts with same drive settings.
+		 * Note: settings are the same for all lanes,
+		 * so comparing first lane is sufficient.
+		 */
+		if (lt_settings->lane_settings[0].VOLTAGE_SWING ==
+			req_settings.lane_settings[0].VOLTAGE_SWING &&
+			lt_settings->lane_settings[0].PRE_EMPHASIS ==
+			req_settings.lane_settings[0].PRE_EMPHASIS)
+			retries_cr++;
+		else
+			retries_cr = 0;
+
+		/* Update VS/PE. */
+		dp_update_drive_settings(lt_settings, req_settings);
+		retry_count++;
+	}
+
+	/* Abort link training if clock recovery failed due to HPD unplug. */
+	if (!link->hpd_status)
+		result = LINK_TRAINING_ABORT;
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) clock recovery\n"
+		" -hop(%d)\n - result(%d)\n - retries(%d)\n",
+		__func__,
+		link->link_id.enum_id - ENUM_ID_1,
+		hop,
+		result,
+		retry_count);
+
+	return result;
+}
+
+/* Execute clock recovery phase of link training in transparent LTTPR mode:
+ * - Driver only issues DPCD transactions and leaves USB4 tunneling (SET_CONFIG) messages to DPIA.
+ * - Driver writes TPS1 to DPCD to kick off training.
+ * - Clock recovery (CR) for link is handled by DPOA, which reports result to DPIA on completion.
+ * - DPIA communicates result to driver by updating CR status when driver reads DPCD.
+ *
+ * @param link DPIA link being trained.
+ * @param lt_settings link_setting and drive settings (voltage swing and pre-emphasis).
+ */
+static enum link_training_result dpia_training_cr_transparent(struct dc_link *link,
+		struct link_training_settings *lt_settings)
+{
+	enum link_training_result result = LINK_TRAINING_CR_FAIL_LANE0;
+	enum dc_status status;
+	uint32_t retries_cr = 0; /* Number of consecutive attempts with same VS or PE. */
+	uint32_t retry_count = 0;
+	uint32_t wait_time_microsec = lt_settings->cr_pattern_time;
+	struct link_training_settings req_settings;
+	enum dc_lane_count lane_count = lt_settings->link_settings.lane_count;
+	union lane_status dpcd_lane_status[LANE_COUNT_DP_MAX] = { { {0} } };
+	union lane_align_status_updated dpcd_lane_status_updated = { {0} };
+
+	/* Cap of LINK_TRAINING_MAX_CR_RETRY attempts at clock recovery.
+	 * Fix inherited from perform_clock_recovery_sequence() -
+	 * the DP equivalent of this function:
+	 * Required for Synaptics MST hub which can put the LT in
+	 * infinite loop by switching the VS between level 0 and level 1
+	 * continuously.
+	 */
+	while ((retries_cr < LINK_TRAINING_MAX_RETRY_COUNT) &&
+	       (retry_count < LINK_TRAINING_MAX_CR_RETRY)) {
+		/* Write TPS1 (not VS or PE) to DPCD to start CR phase.
+		 * DPIA sends SET_CONFIG(SET_LINK) to notify DPOA to
+		 * start link training.
+		 */
+		if (retry_count == 0) {
+			status = dpcd_set_lt_pattern(link, lt_settings->pattern_for_cr, DPRX);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+		}
+
+		dp_wait_for_training_aux_rd_interval(link, wait_time_microsec);
+
+		/* Read status and adjustment requests from DPCD. */
+		status = dp_get_lane_status_and_drive_settings(link,
+				lt_settings,
+				dpcd_lane_status,
+				&dpcd_lane_status_updated,
+				&req_settings,
+				DPRX);
+		if (status != DC_OK) {
+			result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		/* Check if clock recovery successful. */
+		if (dp_is_cr_done(lane_count, dpcd_lane_status)) {
+			result = LINK_TRAINING_SUCCESS;
+			break;
+		}
+
+		result = dp_get_cr_failure(lane_count, dpcd_lane_status);
+
+		if (dp_is_max_vs_reached(lt_settings))
+			break;
+
+		/* Count number of attempts with same drive settings.
+		 * Note: settings are the same for all lanes,
+		 * so comparing first lane is sufficient.
+		 */
+		if (lt_settings->lane_settings[0].VOLTAGE_SWING ==
+			req_settings.lane_settings[0].VOLTAGE_SWING &&
+			lt_settings->lane_settings[0].PRE_EMPHASIS ==
+			req_settings.lane_settings[0].PRE_EMPHASIS)
+			retries_cr++;
+		else
+			retries_cr = 0;
+
+		/* Update VS/PE. */
+		dp_update_drive_settings(lt_settings, req_settings);
+		retry_count++;
+	}
+
+	/* Abort link training if clock recovery failed due to HPD unplug. */
+	if (!link->hpd_status)
+		result = LINK_TRAINING_ABORT;
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) clock recovery\n"
+		" -hop(%d)\n - result(%d)\n - retries(%d)\n",
+		__func__,
+		link->link_id.enum_id - ENUM_ID_1,
+		DPRX,
+		result,
+		retry_count);
+
+	return result;
+}
+
+/* Execute clock recovery phase of link training for specified hop in display
+ * path.
+ *
+ * @param link DPIA link being trained.
+ * @param lt_settings link_setting and drive settings (voltage swing and pre-emphasis).
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static enum link_training_result dpia_training_cr_phase(struct dc_link *link,
+		struct link_training_settings *lt_settings,
+		uint32_t hop)
+{
+	enum link_training_result result = LINK_TRAINING_CR_FAIL_LANE0;
+
+	if (link->lttpr_mode == LTTPR_MODE_NON_TRANSPARENT)
+		result = dpia_training_cr_non_transparent(link, lt_settings, hop);
+	else
+		result = dpia_training_cr_transparent(link, lt_settings);
+
+	return result;
+}
+
+/* Return status read interval during equalization phase. */
+static uint32_t dpia_get_eq_aux_rd_interval(const struct dc_link *link,
+		const struct link_training_settings *lt_settings,
+		uint32_t hop)
+{
+	uint32_t wait_time_microsec;
+
+	if (hop == DPRX)
+		wait_time_microsec = lt_settings->eq_pattern_time;
+	else
+		wait_time_microsec =
+				dp_translate_training_aux_read_interval(
+					link->dpcd_caps.lttpr_caps.aux_rd_interval[hop - 1]);
+
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+	/* Check debug option for extending aux read interval. */
+	if (link->dc->debug.dpia_debug.bits.extend_aux_rd_interval)
+		wait_time_microsec = DPIA_DEBUG_EXTENDED_AUX_RD_INTERVAL_US;
+#endif
+
+	return wait_time_microsec;
+}
+
+/* Execute equalization phase of link training for specified hop in display
+ * path in non-transparent mode:
+ * - driver issues both DPCD and SET_CONFIG transactions.
+ * - TPSx is transmitted for any hops downstream of DPOA.
+ * - Drive (VS/PE) only transmitted for the hop immediately downstream of DPOA.
+ * - EQ for the first hop (DPTX-to-DPIA) is assumed to be successful.
+ * - DPRX EQ only reported successful when both DPRX and DPIA requirements
+ * (clk sync packets sent) fulfilled.
+ *
+ * @param link DPIA link being trained.
+ * @param lt_settings link_setting and drive settings (voltage swing and pre-emphasis).
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static enum link_training_result dpia_training_eq_non_transparent(struct dc_link *link,
+		struct link_training_settings *lt_settings,
+		uint32_t hop)
+{
+	enum link_training_result result = LINK_TRAINING_EQ_FAIL_EQ;
+	uint8_t repeater_cnt = 0; /* Number of hops/repeaters in display path. */
+	uint32_t retries_eq = 0;
+	enum dc_status status;
+	enum dc_dp_training_pattern tr_pattern;
+	uint32_t wait_time_microsec;
+	struct link_training_settings req_settings;
+	enum dc_lane_count lane_count = lt_settings->link_settings.lane_count;
+	union lane_align_status_updated dpcd_lane_status_updated = { {0} };
+	union lane_status dpcd_lane_status[LANE_COUNT_DP_MAX] = { { {0} } };
+	uint8_t set_cfg_data;
+	enum dpia_set_config_ts ts;
+
+	/* Training pattern is TPS4 for repeater;
+	 * TPS2/3/4 for DPRX depending on what it supports.
+	 */
+	if (hop == DPRX)
+		tr_pattern = lt_settings->pattern_for_eq;
+	else
+		tr_pattern = DP_TRAINING_PATTERN_SEQUENCE_4;
+
+	repeater_cnt = dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt);
+
+	for (retries_eq = 0; retries_eq < LINK_TRAINING_MAX_RETRY_COUNT; retries_eq++) {
+		/* DPTX-to-DPIA equalization always successful. */
+		if (hop == repeater_cnt) {
+			result = LINK_TRAINING_SUCCESS;
+			break;
+		}
+
+		/* Instruct DPOA to transmit TPSn then update DPCD. */
+		if (retries_eq == 0) {
+			ts = convert_trng_ptn_to_trng_stg(tr_pattern);
+			status = core_link_send_set_config(link,
+					DPIA_SET_CFG_SET_TRAINING,
+					ts);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+			status = dpcd_set_lt_pattern(link, tr_pattern, hop);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+		}
+
+		/* Update DPOA drive settings then DPCD. DPOA only adjusts
+		 * drive settings for hop immediately downstream.
+		 */
+		if (hop == repeater_cnt - 1) {
+			set_cfg_data = dpia_build_set_config_data(DPIA_SET_CFG_SET_VSPE,
+								  link,
+								  lt_settings);
+			status = core_link_send_set_config(link,
+							   DPIA_SET_CFG_SET_VSPE,
+							   set_cfg_data);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+		}
+		status = dpcd_set_lane_settings(link, lt_settings, hop);
+		if (status != DC_OK) {
+			result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		/* Extend wait time on second equalisation attempt on final hop to
+		 * ensure clock sync packets have been sent.
+		 */
+		if (hop == DPRX && retries_eq == 1)
+			wait_time_microsec = max(wait_time_microsec, (uint32_t)DPIA_CLK_SYNC_DELAY);
+		else
+			wait_time_microsec = dpia_get_eq_aux_rd_interval(link, lt_settings, hop);
+
+		dp_wait_for_training_aux_rd_interval(link, wait_time_microsec);
+
+		/* Read status and adjustment requests from DPCD. */
+		status = dp_get_lane_status_and_drive_settings(link,
+				lt_settings,
+				dpcd_lane_status,
+				&dpcd_lane_status_updated,
+				&req_settings,
+				hop);
+		if (status != DC_OK) {
+			result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		/* CR can still fail during EQ phase. Fail training if CR fails. */
+		if (!dp_is_cr_done(lane_count, dpcd_lane_status)) {
+			result = LINK_TRAINING_EQ_FAIL_CR;
+			break;
+		}
+
+		if (dp_is_ch_eq_done(lane_count, dpcd_lane_status) &&
+		    dp_is_symbol_locked(link->cur_link_settings.lane_count, dpcd_lane_status) &&
+		    dp_is_interlane_aligned(dpcd_lane_status_updated)) {
+			result =  LINK_TRAINING_SUCCESS;
+			break;
+		}
+
+		/* Update VS/PE. */
+		dp_update_drive_settings(lt_settings, req_settings);
+	}
+
+	/* Abort link training if equalization failed due to HPD unplug. */
+	if (!link->hpd_status)
+		result = LINK_TRAINING_ABORT;
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) equalization\n"
+		" - hop(%d)\n - result(%d)\n - retries(%d)\n",
+		__func__,
+		link->link_id.enum_id - ENUM_ID_1,
+		hop,
+		result,
+		retries_eq);
+
+	return result;
+}
+
+/* Execute equalization phase of link training for specified hop in display
+ * path in transparent LTTPR mode:
+ * - driver only issues DPCD transactions leaves USB4 tunneling (SET_CONFIG) messages to DPIA.
+ * - driver writes TPSx to DPCD to notify DPIA that is in equalization phase.
+ * - equalization (EQ) for link is handled by DPOA, which reports result to DPIA on completion.
+ * - DPIA communicates result to driver by updating EQ status when driver reads DPCD.
+ *
+ * @param link DPIA link being trained.
+ * @param lt_settings link_setting and drive settings (voltage swing and pre-emphasis).
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static enum link_training_result dpia_training_eq_transparent(struct dc_link *link,
+		struct link_training_settings *lt_settings)
+{
+	enum link_training_result result = LINK_TRAINING_EQ_FAIL_EQ;
+	uint32_t retries_eq = 0;
+	enum dc_status status;
+	enum dc_dp_training_pattern tr_pattern = lt_settings->pattern_for_eq;
+	uint32_t wait_time_microsec;
+	struct link_training_settings req_settings;
+	enum dc_lane_count lane_count = lt_settings->link_settings.lane_count;
+	union lane_align_status_updated dpcd_lane_status_updated = { {0} };
+	union lane_status dpcd_lane_status[LANE_COUNT_DP_MAX] = { { {0} } };
+
+	wait_time_microsec = dpia_get_eq_aux_rd_interval(link, lt_settings, DPRX);
+
+	for (retries_eq = 0; retries_eq < LINK_TRAINING_MAX_RETRY_COUNT; retries_eq++) {
+		if (retries_eq == 0) {
+			status = dpcd_set_lt_pattern(link, tr_pattern, DPRX);
+			if (status != DC_OK) {
+				result = LINK_TRAINING_ABORT;
+				break;
+			}
+		}
+
+		dp_wait_for_training_aux_rd_interval(link, wait_time_microsec);
+
+		/* Read status and adjustment requests from DPCD. */
+		status = dp_get_lane_status_and_drive_settings(link,
+				lt_settings,
+				dpcd_lane_status,
+				&dpcd_lane_status_updated,
+				&req_settings,
+				DPRX);
+		if (status != DC_OK) {
+			result = LINK_TRAINING_ABORT;
+			break;
+		}
+
+		/* CR can still fail during EQ phase. Fail training if CR fails. */
+		if (!dp_is_cr_done(lane_count, dpcd_lane_status)) {
+			result = LINK_TRAINING_EQ_FAIL_CR;
+			break;
+		}
+
+		if (dp_is_ch_eq_done(lane_count, dpcd_lane_status) &&
+		    dp_is_symbol_locked(link->cur_link_settings.lane_count, dpcd_lane_status) &&
+		    dp_is_interlane_aligned(dpcd_lane_status_updated)) {
+			result =  LINK_TRAINING_SUCCESS;
+			break;
+		}
+
+		/* Update VS/PE. */
+		dp_update_drive_settings(lt_settings, req_settings);
+	}
+
+	/* Abort link training if equalization failed due to HPD unplug. */
+	if (!link->hpd_status)
+		result = LINK_TRAINING_ABORT;
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) equalization\n"
+		" - hop(%d)\n - result(%d)\n - retries(%d)\n",
+		__func__,
+		link->link_id.enum_id - ENUM_ID_1,
+		DPRX,
+		result,
+		retries_eq);
+
+	return result;
+}
+
+/* Execute equalization phase of link training for specified hop in display
+ * path.
+ *
+ * @param link DPIA link being trained.
+ * @param lt_settings link_setting and drive settings (voltage swing and pre-emphasis).
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static enum link_training_result dpia_training_eq_phase(struct dc_link *link,
+		struct link_training_settings *lt_settings,
+		uint32_t hop)
+{
+	enum link_training_result result = LINK_TRAINING_EQ_FAIL_EQ;
+
+	if (link->lttpr_mode == LTTPR_MODE_NON_TRANSPARENT)
+		result = dpia_training_eq_non_transparent(link, lt_settings, hop);
+	else
+		result = dpia_training_eq_transparent(link, lt_settings);
+
+	return result;
+}
+
+/* End training of specified hop in display path. */
+static enum dc_status dpcd_clear_lt_pattern(struct dc_link *link, uint32_t hop)
+{
+	union dpcd_training_pattern dpcd_pattern = { {0} };
+	uint32_t dpcd_tps_offset = DP_TRAINING_PATTERN_SET;
+	enum dc_status status;
+
+	if (hop != DPRX)
+		dpcd_tps_offset = DP_TRAINING_PATTERN_SET_PHY_REPEATER1 +
+			((DP_REPEATER_CONFIGURATION_AND_STATUS_SIZE) * (hop - 1));
+
+	status = core_link_write_dpcd(link,
+			dpcd_tps_offset,
+			&dpcd_pattern.raw,
+			sizeof(dpcd_pattern.raw));
+
+	return status;
+}
+
+/* End training of specified hop in display path.
+ *
+ * In transparent LTTPR mode:
+ * - driver clears training pattern for the specified hop in DPCD.
+ * In non-transparent LTTPR mode:
+ * - in addition to clearing training pattern, driver issues USB4 tunneling
+ * (SET_CONFIG) messages to notify DPOA when training is done for first hop
+ * (DPTX-to-DPIA) and last hop (DPRX).
+ *
+ * @param link DPIA link being trained.
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static enum link_training_result dpia_training_end(struct dc_link *link,
+		uint32_t hop)
+{
+	enum link_training_result result = LINK_TRAINING_SUCCESS;
+	uint8_t repeater_cnt = 0; /* Number of hops/repeaters in display path. */
+	enum dc_status status;
+
+	if (link->lttpr_mode == LTTPR_MODE_NON_TRANSPARENT) {
+		repeater_cnt = dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt);
+
+		if (hop == repeater_cnt) { /* DPTX-to-DPIA */
+			/* Send SET_CONFIG(SET_TRAINING:0xff) to notify DPOA that
+			 * DPTX-to-DPIA hop trained. No DPCD write needed for first hop.
+			 */
+			status = core_link_send_set_config(link,
+					DPIA_SET_CFG_SET_TRAINING,
+					DPIA_TS_UFP_DONE);
+			if (status != DC_OK)
+				result = LINK_TRAINING_ABORT;
+		} else { /* DPOA-to-x */
+			/* Write 0x0 to TRAINING_PATTERN_SET */
+			status = dpcd_clear_lt_pattern(link, hop);
+			if (status != DC_OK)
+				result = LINK_TRAINING_ABORT;
+		}
+
+		/* Notify DPOA that non-transparent link training of DPRX done. */
+		if (hop == DPRX && result != LINK_TRAINING_ABORT) {
+			status = core_link_send_set_config(link,
+					DPIA_SET_CFG_SET_TRAINING,
+					DPIA_TS_DPRX_DONE);
+			if (status != DC_OK)
+				result = LINK_TRAINING_ABORT;
+		}
+
+	} else { /* non-LTTPR or transparent LTTPR. */
+		/* Write 0x0 to TRAINING_PATTERN_SET */
+		status = dpcd_clear_lt_pattern(link, hop);
+		if (status != DC_OK)
+			result = LINK_TRAINING_ABORT;
+	}
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) end\n - hop(%d)\n - result(%d)\n - LTTPR mode(%d)\n",
+				__func__,
+				link->link_id.enum_id - ENUM_ID_1,
+				hop,
+				result,
+				link->lttpr_mode);
+
+	return result;
+}
+
+/* When aborting training of specified hop in display path, clean up by:
+ * - Attempting to clear DPCD TRAINING_PATTERN_SET, LINK_BW_SET and LANE_COUNT_SET.
+ * - Sending SET_CONFIG(SET_LINK) with lane count and link rate set to 0.
+ *
+ * @param link DPIA link being trained.
+ * @param hop The Hop in display path. DPRX = 0.
+ */
+static void dpia_training_abort(struct dc_link *link, uint32_t hop)
+{
+	uint8_t data = 0;
+	uint32_t dpcd_tps_offset = DP_TRAINING_PATTERN_SET;
+
+	DC_LOG_HW_LINK_TRAINING("%s\n DPIA(%d) aborting\n - LTTPR mode(%d)\n - HPD(%d)\n",
+				__func__,
+				link->link_id.enum_id - ENUM_ID_1,
+				link->lttpr_mode,
+				link->hpd_status);
+
+	/* Abandon clean-up if sink unplugged. */
+	if (!link->hpd_status)
+		return;
+
+	if (hop != DPRX)
+		dpcd_tps_offset = DP_TRAINING_PATTERN_SET_PHY_REPEATER1 +
+			((DP_REPEATER_CONFIGURATION_AND_STATUS_SIZE) * (hop - 1));
+
+	core_link_write_dpcd(link, dpcd_tps_offset, &data, 1);
+	core_link_write_dpcd(link, DP_LINK_BW_SET, &data, 1);
+	core_link_write_dpcd(link, DP_LANE_COUNT_SET, &data, 1);
+	core_link_send_set_config(link, DPIA_SET_CFG_SET_LINK, data);
+}
+
+enum link_training_result dc_link_dpia_perform_link_training(struct dc_link *link,
+	const struct dc_link_settings *link_setting,
+	bool skip_video_pattern)
+{
+	enum link_training_result result;
+	struct link_training_settings lt_settings;
+	uint8_t repeater_cnt = 0; /* Number of hops/repeaters in display path. */
+	int8_t repeater_id; /* Current hop. */
+
+	/* Configure link as prescribed in link_setting and set LTTPR mode. */
+	result = dpia_configure_link(link, link_setting, &lt_settings);
+	if (result != LINK_TRAINING_SUCCESS)
+		return result;
+
+	if (link->lttpr_mode == LTTPR_MODE_NON_TRANSPARENT)
+		repeater_cnt = dp_convert_to_count(link->dpcd_caps.lttpr_caps.phy_repeater_cnt);
+
+	/* Train each hop in turn starting with the one closest to DPTX.
+	 * In transparent or non-LTTPR mode, train only the final hop (DPRX).
+	 */
+	for (repeater_id = repeater_cnt; repeater_id >= 0; repeater_id--) {
+		/* Clock recovery. */
+		result = dpia_training_cr_phase(link, &lt_settings, repeater_id);
+		if (result != LINK_TRAINING_SUCCESS)
+			break;
+
+		/* Equalization. */
+		result = dpia_training_eq_phase(link, &lt_settings, repeater_id);
+		if (result != LINK_TRAINING_SUCCESS)
+			break;
+
+		/* Stop training hop. */
+		result = dpia_training_end(link, repeater_id);
+		if (result != LINK_TRAINING_SUCCESS)
+			break;
+	}
+
+	/* Double-check link status if training successful; gracefully abort
+	 * training of current hop if training failed due to message tunneling
+	 * failure; end training of hop if training ended conventionally and
+	 * falling back to lower bandwidth settings possible.
+	 */
+	if (result == LINK_TRAINING_SUCCESS) {
+		msleep(5);
+		result = dp_check_link_loss_status(link, &lt_settings);
+	} else if (result == LINK_TRAINING_ABORT) {
+		dpia_training_abort(link, repeater_id);
+	} else {
+		dpia_training_end(link, repeater_id);
+	}
+	return result;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link_enc_cfg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link_enc_cfg.c
@@ -1,5 +1,4 @@
-/*
- * Copyright 2021 Advanced Micro Devices, Inc.
+/* Copyright 2021 Advanced Micro Devices, Inc. All rights reserved.
  *
  * Permission is hereby granted, free of charge, to any person obtaining a
  * copy of this software and associated documentation files (the "Software"),
@@ -35,78 +34,131 @@
 	int i;
 
 	/* Loop over created link encoder objects. */
-	for (i = 0; i < stream->ctx->dc->res_pool->res_cap->num_dig_link_enc; i++) {
-		link_enc = stream->ctx->dc->res_pool->link_encoders[i];
-
-		if (link_enc &&
-				((uint32_t)stream->signal & link_enc->output_signals)) {
-			if (dc_is_dp_signal(stream->signal)) {
-				/* DIGs do not support DP2.0 streams with 128b/132b encoding. */
-				struct dc_link_settings link_settings = {0};
-
-				decide_link_settings(stream, &link_settings);
-				if ((link_settings.link_rate >= LINK_RATE_LOW) &&
-						link_settings.link_rate <= LINK_RATE_HIGH3) {
+	if (stream) {
+		for (i = 0; i < stream->ctx->dc->res_pool->res_cap->num_dig_link_enc; i++) {
+			link_enc = stream->ctx->dc->res_pool->link_encoders[i];
+
+			/* Need to check link signal type rather than stream signal type which may not
+			 * yet match.
+			 */
+			if (link_enc && ((uint32_t)stream->link->connector_signal & link_enc->output_signals)) {
+				if (dc_is_dp_signal(stream->signal)) {
+					/* DIGs do not support DP2.0 streams with 128b/132b encoding. */
+					struct dc_link_settings link_settings = {0};
+
+					decide_link_settings(stream, &link_settings);
+					if ((link_settings.link_rate >= LINK_RATE_LOW) &&
+							link_settings.link_rate <= LINK_RATE_HIGH3) {
+						is_dig_stream = true;
+						break;
+					}
+				} else {
 					is_dig_stream = true;
 					break;
 				}
-			} else {
-				is_dig_stream = true;
-				break;
 			}
 		}
 	}
-
 	return is_dig_stream;
 }
 
-/* Update DIG link encoder resource tracking variables in dc_state. */
-static void update_link_enc_assignment(
+static struct link_enc_assignment get_assignment(struct dc *dc, int i)
+{
+	struct link_enc_assignment assignment;
+
+	if (dc->current_state->res_ctx.link_enc_cfg_ctx.mode == LINK_ENC_CFG_TRANSIENT)
+		assignment = dc->current_state->res_ctx.link_enc_cfg_ctx.transient_assignments[i];
+	else /* LINK_ENC_CFG_STEADY */
+		assignment = dc->current_state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+	return assignment;
+}
+
+/* Return stream using DIG link encoder resource. NULL if unused. */
+static struct dc_stream_state *get_stream_using_link_enc(
+		struct dc_state *state,
+		enum engine_id eng_id)
+{
+	struct dc_stream_state *stream = NULL;
+	int i;
+
+	for (i = 0; i < state->stream_count; i++) {
+		struct link_enc_assignment assignment = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+		if ((assignment.valid == true) && (assignment.eng_id == eng_id)) {
+			stream = state->streams[i];
+			break;
+		}
+	}
+
+	return stream;
+}
+
+static void remove_link_enc_assignment(
 		struct dc_state *state,
 		struct dc_stream_state *stream,
-		enum engine_id eng_id,
-		bool add_enc)
+		enum engine_id eng_id)
 {
 	int eng_idx;
-	int stream_idx;
 	int i;
 
 	if (eng_id != ENGINE_ID_UNKNOWN) {
 		eng_idx = eng_id - ENGINE_ID_DIGA;
-		stream_idx = -1;
 
-		/* Index of stream in dc_state used to update correct entry in
+		/* stream ptr of stream in dc_state used to update correct entry in
 		 * link_enc_assignments table.
 		 */
-		for (i = 0; i < state->stream_count; i++) {
-			if (stream == state->streams[i]) {
-				stream_idx = i;
+		for (i = 0; i < MAX_PIPES; i++) {
+			struct link_enc_assignment assignment = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+			if (assignment.valid && assignment.stream == stream) {
+				state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].valid = false;
+				/* Only add link encoder back to availability pool if not being
+				 * used by any other stream (i.e. removing SST stream or last MST stream).
+				 */
+				if (get_stream_using_link_enc(state, eng_id) == NULL)
+					state->res_ctx.link_enc_cfg_ctx.link_enc_avail[eng_idx] = eng_id;
+
+				stream->link_enc = NULL;
+				state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].eng_id = ENGINE_ID_UNKNOWN;
+				state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].stream = NULL;
 				break;
 			}
 		}
+	}
+}
 
-		/* Update link encoder assignments table, link encoder availability
-		 * pool and link encoder assigned to stream in state.
-		 * Add/remove encoder resource to/from stream.
+static void add_link_enc_assignment(
+		struct dc_state *state,
+		struct dc_stream_state *stream,
+		enum engine_id eng_id)
+{
+	int eng_idx;
+	int i;
+
+	if (eng_id != ENGINE_ID_UNKNOWN) {
+		eng_idx = eng_id - ENGINE_ID_DIGA;
+
+		/* stream ptr of stream in dc_state used to update correct entry in
+		 * link_enc_assignments table.
 		 */
-		if (stream_idx != -1) {
-			if (add_enc) {
-				state->res_ctx.link_enc_assignments[stream_idx] = (struct link_enc_assignment){
+		for (i = 0; i < state->stream_count; i++) {
+			if (stream == state->streams[i]) {
+				state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i] = (struct link_enc_assignment){
 					.valid = true,
 					.ep_id = (struct display_endpoint_id) {
 						.link_id = stream->link->link_id,
 						.ep_type = stream->link->ep_type},
-					.eng_id = eng_id};
-				state->res_ctx.link_enc_avail[eng_idx] = ENGINE_ID_UNKNOWN;
+					.eng_id = eng_id,
+					.stream = stream};
+				state->res_ctx.link_enc_cfg_ctx.link_enc_avail[eng_idx] = ENGINE_ID_UNKNOWN;
 				stream->link_enc = stream->ctx->dc->res_pool->link_encoders[eng_idx];
-			} else {
-				state->res_ctx.link_enc_assignments[stream_idx].valid = false;
-				state->res_ctx.link_enc_avail[eng_idx] = eng_id;
-				stream->link_enc = NULL;
+				break;
 			}
-		} else {
-			dm_output_to_console("%s: Stream not found in dc_state.\n", __func__);
 		}
+
+		/* Attempted to add an encoder assignment for a stream not in dc_state. */
+		ASSERT(i != state->stream_count);
 	}
 }
 
@@ -119,7 +171,7 @@
 	int i;
 
 	for (i = 0; i < ctx->dc->res_pool->res_cap->num_dig_link_enc; i++) {
-		eng_id = state->res_ctx.link_enc_avail[i];
+		eng_id = state->res_ctx.link_enc_cfg_ctx.link_enc_avail[i];
 		if (eng_id != ENGINE_ID_UNKNOWN)
 			break;
 	}
@@ -127,46 +179,94 @@
 	return eng_id;
 }
 
-/* Return stream using DIG link encoder resource. NULL if unused. */
-static struct dc_stream_state *get_stream_using_link_enc(
+/* Check for availability of link encoder eng_id. */
+static bool is_avail_link_enc(struct dc_state *state, enum engine_id eng_id, struct dc_stream_state *stream)
+{
+	bool is_avail = false;
+	int eng_idx = eng_id - ENGINE_ID_DIGA;
+
+	/* An encoder is available if it is still in the availability pool. */
+	if (eng_id != ENGINE_ID_UNKNOWN && state->res_ctx.link_enc_cfg_ctx.link_enc_avail[eng_idx] != ENGINE_ID_UNKNOWN) {
+		is_avail = true;
+	} else {
+		struct dc_stream_state *stream_assigned = NULL;
+
+		/* MST streams share the same link and should share the same encoder.
+		 * If a stream that has already been assigned a link encoder uses as the
+		 * same link as the stream checking for availability, it is an MST stream
+		 * and should use the same link encoder.
+		 */
+		stream_assigned = get_stream_using_link_enc(state, eng_id);
+		if (stream_assigned && stream != stream_assigned && stream->link == stream_assigned->link)
+			is_avail = true;
+	}
+
+	return is_avail;
+}
+
+/* Test for display_endpoint_id equality. */
+static bool are_ep_ids_equal(struct display_endpoint_id *lhs, struct display_endpoint_id *rhs)
+{
+	bool are_equal = false;
+
+	if (lhs->link_id.id == rhs->link_id.id &&
+			lhs->link_id.enum_id == rhs->link_id.enum_id &&
+			lhs->link_id.type == rhs->link_id.type &&
+			lhs->ep_type == rhs->ep_type)
+		are_equal = true;
+
+	return are_equal;
+}
+
+static struct link_encoder *get_link_enc_used_by_link(
 		struct dc_state *state,
-		enum engine_id eng_id)
+		const struct dc_link *link)
 {
-	struct dc_stream_state *stream = NULL;
-	int stream_idx = -1;
+	struct link_encoder *link_enc = NULL;
+	struct display_endpoint_id ep_id;
 	int i;
 
-	for (i = 0; i < state->stream_count; i++) {
-		struct link_enc_assignment assignment = state->res_ctx.link_enc_assignments[i];
+	ep_id = (struct display_endpoint_id) {
+		.link_id = link->link_id,
+		.ep_type = link->ep_type};
 
-		if (assignment.valid && (assignment.eng_id == eng_id)) {
-			stream_idx = i;
-			break;
-		}
-	}
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
 
-	if (stream_idx != -1)
-		stream = state->streams[stream_idx];
-	else
-		dm_output_to_console("%s: No stream using DIG(%d).\n", __func__, eng_id);
+		if (assignment.valid == true && are_ep_ids_equal(&assignment.ep_id, &ep_id))
+			link_enc = link->dc->res_pool->link_encoders[assignment.eng_id - ENGINE_ID_DIGA];
+	}
 
-	return stream;
+	return link_enc;
 }
-
-void link_enc_cfg_init(
-		struct dc *dc,
-		struct dc_state *state)
+/* Clear all link encoder assignments. */
+static void clear_enc_assignments(const struct dc *dc, struct dc_state *state)
 {
 	int i;
 
+	for (i = 0; i < MAX_PIPES; i++) {
+		state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].valid = false;
+		state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].eng_id = ENGINE_ID_UNKNOWN;
+		state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].stream = NULL;
+	}
+
 	for (i = 0; i < dc->res_pool->res_cap->num_dig_link_enc; i++) {
 		if (dc->res_pool->link_encoders[i])
-			state->res_ctx.link_enc_avail[i] = (enum engine_id) i;
+			state->res_ctx.link_enc_cfg_ctx.link_enc_avail[i] = (enum engine_id) i;
 		else
-			state->res_ctx.link_enc_avail[i] = ENGINE_ID_UNKNOWN;
+			state->res_ctx.link_enc_cfg_ctx.link_enc_avail[i] = ENGINE_ID_UNKNOWN;
 	}
 }
 
+void link_enc_cfg_init(
+		const struct dc *dc,
+		struct dc_state *state)
+{
+	clear_enc_assignments(dc, state);
+
+	state->res_ctx.link_enc_cfg_ctx.mode = LINK_ENC_CFG_STEADY;
+}
+
 void link_enc_cfg_link_encs_assign(
 		struct dc *dc,
 		struct dc_state *state,
@@ -175,10 +275,16 @@
 {
 	enum engine_id eng_id = ENGINE_ID_UNKNOWN;
 	int i;
+	int j;
+
+	ASSERT(state->stream_count == stream_count);
 
 	/* Release DIG link encoder resources before running assignment algorithm. */
-	for (i = 0; i < stream_count; i++)
-		dc->res_pool->funcs->link_enc_unassign(state, streams[i]);
+	for (i = 0; i < dc->current_state->stream_count; i++)
+		dc->res_pool->funcs->link_enc_unassign(state, dc->current_state->streams[i]);
+
+	for (i = 0; i < MAX_PIPES; i++)
+		ASSERT(state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].valid == false);
 
 	/* (a) Assign DIG link encoders to physical (unmappable) endpoints first. */
 	for (i = 0; i < stream_count; i++) {
@@ -191,26 +297,82 @@
 		/* Physical endpoints have a fixed mapping to DIG link encoders. */
 		if (!stream->link->is_dig_mapping_flexible) {
 			eng_id = stream->link->eng_id;
-			update_link_enc_assignment(state, stream, eng_id, true);
+			add_link_enc_assignment(state, stream, eng_id);
+		}
+	}
+
+	/* (b) Retain previous assignments for mappable endpoints if encoders still available. */
+	eng_id = ENGINE_ID_UNKNOWN;
+
+	if (state != dc->current_state) {
+		struct dc_state *prev_state = dc->current_state;
+
+		for (i = 0; i < stream_count; i++) {
+			struct dc_stream_state *stream = state->streams[i];
+
+			/* Skip stream if not supported by DIG link encoder. */
+			if (!is_dig_link_enc_stream(stream))
+				continue;
+
+			if (!stream->link->is_dig_mapping_flexible)
+				continue;
+
+			for (j = 0; j < prev_state->stream_count; j++) {
+				struct dc_stream_state *prev_stream = prev_state->streams[j];
+
+				if (stream == prev_stream && stream->link == prev_stream->link &&
+						prev_state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[j].valid) {
+					eng_id = prev_state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[j].eng_id;
+					if (is_avail_link_enc(state, eng_id, stream))
+						add_link_enc_assignment(state, stream, eng_id);
+				}
+			}
 		}
 	}
 
-	/* (b) Then assign encoders to mappable endpoints. */
+	/* (c) Then assign encoders to remaining mappable endpoints. */
 	eng_id = ENGINE_ID_UNKNOWN;
 
 	for (i = 0; i < stream_count; i++) {
 		struct dc_stream_state *stream = streams[i];
 
 		/* Skip stream if not supported by DIG link encoder. */
-		if (!is_dig_link_enc_stream(stream))
+		if (!is_dig_link_enc_stream(stream)) {
+			ASSERT(stream->link->is_dig_mapping_flexible != true);
 			continue;
+		}
 
 		/* Mappable endpoints have a flexible mapping to DIG link encoders. */
 		if (stream->link->is_dig_mapping_flexible) {
-			eng_id = find_first_avail_link_enc(stream->ctx, state);
-			update_link_enc_assignment(state, stream, eng_id, true);
+			struct link_encoder *link_enc = NULL;
+
+			/* Skip if encoder assignment retained in step (b) above. */
+			if (stream->link_enc)
+				continue;
+
+			/* For MST, multiple streams will share the same link / display
+			 * endpoint. These streams should use the same link encoder
+			 * assigned to that endpoint.
+			 */
+			link_enc = get_link_enc_used_by_link(state, stream->link);
+			if (link_enc == NULL)
+				eng_id = find_first_avail_link_enc(stream->ctx, state);
+			else
+				eng_id =  link_enc->preferred_engine;
+			add_link_enc_assignment(state, stream, eng_id);
 		}
 	}
+
+	link_enc_cfg_validate(dc, state);
+
+	/* Update transient assignments. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		dc->current_state->res_ctx.link_enc_cfg_ctx.transient_assignments[i] =
+			state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+	}
+
+	/* Current state mode will be set to steady once this state committed. */
+	state->res_ctx.link_enc_cfg_ctx.mode = LINK_ENC_CFG_STEADY;
 }
 
 void link_enc_cfg_link_enc_unassign(
@@ -226,16 +388,16 @@
 	if (stream->link_enc)
 		eng_id = stream->link_enc->preferred_engine;
 
-	update_link_enc_assignment(state, stream, eng_id, false);
+	remove_link_enc_assignment(state, stream, eng_id);
 }
 
 bool link_enc_cfg_is_transmitter_mappable(
-		struct dc_state *state,
+		struct dc *dc,
 		struct link_encoder *link_enc)
 {
 	bool is_mappable = false;
 	enum engine_id eng_id = link_enc->preferred_engine;
-	struct dc_stream_state *stream = get_stream_using_link_enc(state, eng_id);
+	struct dc_stream_state *stream = link_enc_cfg_get_stream_using_link_enc(dc, eng_id);
 
 	if (stream)
 		is_mappable = stream->link->is_dig_mapping_flexible;
@@ -243,73 +405,225 @@
 	return is_mappable;
 }
 
-struct dc_link *link_enc_cfg_get_link_using_link_enc(
-		struct dc_state *state,
+struct dc_stream_state *link_enc_cfg_get_stream_using_link_enc(
+		struct dc *dc,
 		enum engine_id eng_id)
 {
-	struct dc_link *link = NULL;
-	int stream_idx = -1;
+	struct dc_stream_state *stream = NULL;
 	int i;
 
-	for (i = 0; i < state->stream_count; i++) {
-		struct link_enc_assignment assignment = state->res_ctx.link_enc_assignments[i];
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = get_assignment(dc, i);
 
-		if (assignment.valid && (assignment.eng_id == eng_id)) {
-			stream_idx = i;
+		if ((assignment.valid == true) && (assignment.eng_id == eng_id)) {
+			stream = assignment.stream;
 			break;
 		}
 	}
 
-	if (stream_idx != -1)
-		link = state->streams[stream_idx]->link;
-	else
-		dm_output_to_console("%s: No link using DIG(%d).\n", __func__, eng_id);
+	return stream;
+}
 
+struct dc_link *link_enc_cfg_get_link_using_link_enc(
+		struct dc *dc,
+		enum engine_id eng_id)
+{
+	struct dc_link *link = NULL;
+	struct dc_stream_state *stream = NULL;
+
+	stream = link_enc_cfg_get_stream_using_link_enc(dc, eng_id);
+
+	if (stream)
+		link = stream->link;
+
+	// dm_output_to_console("%s: No link using DIG(%d).\n", __func__, eng_id);
 	return link;
 }
 
 struct link_encoder *link_enc_cfg_get_link_enc_used_by_link(
-		struct dc_state *state,
+		struct dc *dc,
 		const struct dc_link *link)
 {
 	struct link_encoder *link_enc = NULL;
 	struct display_endpoint_id ep_id;
-	int stream_idx = -1;
 	int i;
 
 	ep_id = (struct display_endpoint_id) {
 		.link_id = link->link_id,
 		.ep_type = link->ep_type};
 
-	for (i = 0; i < state->stream_count; i++) {
-		struct link_enc_assignment assignment = state->res_ctx.link_enc_assignments[i];
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = get_assignment(dc, i);
 
-		if (assignment.valid &&
-				assignment.ep_id.link_id.id == ep_id.link_id.id &&
-				assignment.ep_id.link_id.enum_id == ep_id.link_id.enum_id &&
-				assignment.ep_id.link_id.type == ep_id.link_id.type &&
-				assignment.ep_id.ep_type == ep_id.ep_type) {
-			stream_idx = i;
+		if (assignment.valid == true && are_ep_ids_equal(&assignment.ep_id, &ep_id)) {
+			link_enc = link->dc->res_pool->link_encoders[assignment.eng_id - ENGINE_ID_DIGA];
 			break;
 		}
 	}
 
-	if (stream_idx != -1)
-		link_enc = state->streams[stream_idx]->link_enc;
-
 	return link_enc;
 }
 
-struct link_encoder *link_enc_cfg_get_next_avail_link_enc(
-	const struct dc *dc,
-	const struct dc_state *state)
+struct link_encoder *link_enc_cfg_get_next_avail_link_enc(struct dc *dc)
 {
 	struct link_encoder *link_enc = NULL;
-	enum engine_id eng_id;
+	enum engine_id encs_assigned[MAX_DIG_LINK_ENCODERS];
+	int i;
+
+	for (i = 0; i < MAX_DIG_LINK_ENCODERS; i++)
+		encs_assigned[i] = ENGINE_ID_UNKNOWN;
+
+	/* Add assigned encoders to list. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = get_assignment(dc, i);
+
+		if (assignment.valid)
+			encs_assigned[assignment.eng_id - ENGINE_ID_DIGA] = assignment.eng_id;
+	}
+
+	for (i = 0; i < dc->res_pool->res_cap->num_dig_link_enc; i++) {
+		if (encs_assigned[i] == ENGINE_ID_UNKNOWN) {
+			link_enc = dc->res_pool->link_encoders[i];
+			break;
+		}
+	}
+
+	return link_enc;
+}
+
+struct link_encoder *link_enc_cfg_get_link_enc_used_by_stream(
+		struct dc *dc,
+		const struct dc_stream_state *stream)
+{
+	struct link_encoder *link_enc;
 
-	eng_id = find_first_avail_link_enc(dc->ctx, state);
-	if (eng_id != ENGINE_ID_UNKNOWN)
-		link_enc = dc->res_pool->link_encoders[eng_id - ENGINE_ID_DIGA];
+	link_enc = link_enc_cfg_get_link_enc_used_by_link(dc, stream->link);
 
 	return link_enc;
 }
+
+bool link_enc_cfg_is_link_enc_avail(struct dc *dc, enum engine_id eng_id)
+{
+	bool is_avail = true;
+	int i;
+
+	/* Add assigned encoders to list. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = get_assignment(dc, i);
+
+		if (assignment.valid && assignment.eng_id == eng_id) {
+			is_avail = false;
+			break;
+		}
+	}
+
+	return is_avail;
+}
+
+bool link_enc_cfg_validate(struct dc *dc, struct dc_state *state)
+{
+	bool is_valid = false;
+	bool valid_entries = true;
+	bool valid_stream_ptrs = true;
+	bool valid_uniqueness = true;
+	bool valid_avail = true;
+	bool valid_streams = true;
+	int i, j;
+	uint8_t valid_count = 0;
+	uint8_t dig_stream_count = 0;
+	int matching_stream_ptrs = 0;
+	int eng_ids_per_ep_id[MAX_PIPES] = {0};
+	int valid_bitmap = 0;
+
+	/* (1) No. valid entries same as stream count. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+		if (assignment.valid)
+			valid_count++;
+
+		if (is_dig_link_enc_stream(state->streams[i]))
+			dig_stream_count++;
+	}
+	if (valid_count != dig_stream_count)
+		valid_entries = false;
+
+	/* (2) Matching stream ptrs. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+		if (assignment.valid) {
+			if (assignment.stream == state->streams[i])
+				matching_stream_ptrs++;
+			else
+				valid_stream_ptrs = false;
+		}
+	}
+
+	/* (3) Each endpoint assigned unique encoder. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment_i = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+		if (assignment_i.valid) {
+			struct display_endpoint_id ep_id_i = assignment_i.ep_id;
+
+			eng_ids_per_ep_id[i]++;
+			for (j = 0; j < MAX_PIPES; j++) {
+				struct link_enc_assignment assignment_j =
+					state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[j];
+
+				if (j == i)
+					continue;
+
+				if (assignment_j.valid) {
+					struct display_endpoint_id ep_id_j = assignment_j.ep_id;
+
+					if (are_ep_ids_equal(&ep_id_i, &ep_id_j) &&
+							assignment_i.eng_id != assignment_j.eng_id) {
+						valid_uniqueness = false;
+						eng_ids_per_ep_id[i]++;
+					}
+				}
+			}
+		}
+	}
+
+	/* (4) Assigned encoders not in available pool. */
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct link_enc_assignment assignment = state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i];
+
+		if (assignment.valid) {
+			for (j = 0; j < dc->res_pool->res_cap->num_dig_link_enc; j++) {
+				if (state->res_ctx.link_enc_cfg_ctx.link_enc_avail[j] == assignment.eng_id) {
+					valid_avail = false;
+					break;
+				}
+			}
+		}
+	}
+
+	/* (5) All streams have valid link encoders. */
+	for (i = 0; i < state->stream_count; i++) {
+		struct dc_stream_state *stream = state->streams[i];
+
+		if (is_dig_link_enc_stream(stream) && stream->link_enc == NULL) {
+			valid_streams = false;
+			break;
+		}
+	}
+
+	is_valid = valid_entries && valid_stream_ptrs && valid_uniqueness && valid_avail && valid_streams;
+	ASSERT(is_valid);
+
+	if (is_valid == false) {
+		valid_bitmap =
+			(valid_entries & 0x1) |
+			((valid_stream_ptrs & 0x1) << 1) |
+			((valid_uniqueness & 0x1) << 2) |
+			((valid_avail & 0x1) << 3) |
+			((valid_streams & 0x1) << 4);
+		dm_error("Invalid link encoder assignments: 0x%x\n", valid_bitmap);
+	}
+
+	return is_valid;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_link_hwss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_link_hwss.c
@@ -61,6 +61,13 @@
 			sizeof(state));
 }
 
+void dp_source_sequence_trace(struct dc_link *link, uint8_t dp_test_mode)
+{
+	if (link->dc->debug.enable_driver_sequence_debug)
+		core_link_write_dpcd(link, DP_SOURCE_SEQUENCE,
+					&dp_test_mode, sizeof(dp_test_mode));
+}
+
 void dp_enable_link_phy(
 	struct dc_link *link,
 	enum signal_type signal,
@@ -79,7 +86,7 @@
 
 	/* Link should always be assigned encoder when en-/disabling. */
 	if (link->is_dig_mapping_flexible && dc->res_pool->funcs->link_encs_assign)
-		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->dc->current_state, link);
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(dc, link);
 	else
 		link_enc = link->link_enc;
 	ASSERT(link_enc);
@@ -132,6 +139,7 @@
 	if (dmcu != NULL && dmcu->funcs->unlock_phy)
 		dmcu->funcs->unlock_phy(dmcu);
 
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_ENABLE_LINK_PHY);
 	dp_receiver_power_ctrl(link, true);
 }
 
@@ -210,7 +218,7 @@
 
 	/* Link should always be assigned encoder when en-/disabling. */
 	if (link->is_dig_mapping_flexible && dc->res_pool->funcs->link_encs_assign)
-		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->dc->current_state, link);
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(dc, link);
 	else
 		link_enc = link->link_enc;
 	ASSERT(link_enc);
@@ -233,6 +241,8 @@
 			dmcu->funcs->unlock_phy(dmcu);
 	}
 
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_DISABLE_LINK_PHY);
+
 	/* Clear current link setting.*/
 	memset(&link->cur_link_settings, 0,
 			sizeof(link->cur_link_settings));
@@ -310,7 +320,7 @@
 	 */
 	if (link->is_dig_mapping_flexible &&
 			link->dc->res_pool->funcs->link_encs_assign)
-		encoder = link_enc_cfg_get_link_enc_used_by_link(link->dc->current_state, link);
+		encoder = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
 	else
 		encoder = link->link_enc;
 
@@ -320,6 +330,7 @@
 	pattern_param.dp_panel_mode = dp_get_panel_mode(link);
 
 	encoder->funcs->dp_set_phy_pattern(encoder, &pattern_param);
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_SET_SOURCE_PATTERN);
 }
 
 void dp_retrain_link_dp_test(struct dc_link *link,
@@ -338,7 +349,7 @@
 			pipes[i].stream->link == link) {
 			udelay(100);
 
-			pipes[i].stream_res.stream_enc->funcs->dp_blank(
+			pipes[i].stream_res.stream_enc->funcs->dp_blank(link,
 					pipes[i].stream_res.stream_enc);
 
 			/* disable any test pattern that might be active */
@@ -351,9 +362,10 @@
 			if ((&pipes[i])->stream_res.audio && !link->dc->debug.az_endpoint_mute_only)
 				(&pipes[i])->stream_res.audio->funcs->az_disable((&pipes[i])->stream_res.audio);
 
-			link->link_enc->funcs->disable_output(
-					link->link_enc,
-					SIGNAL_TYPE_DISPLAY_PORT);
+			if (link->link_enc)
+				link->link_enc->funcs->disable_output(
+						link->link_enc,
+						SIGNAL_TYPE_DISPLAY_PORT);
 
 			/* Clear current link setting. */
 			memset(&link->cur_link_settings, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_resource.c
@@ -41,6 +41,7 @@
 #include "set_mode_types.h"
 #include "virtual/virtual_stream_encoder.h"
 #include "dpcd_defs.h"
+#include "link_enc_cfg.h"
 
 #if defined(CONFIG_DRM_AMD_DC_SI)
 #include "dce60/dce60_resource.h"
@@ -1025,6 +1026,16 @@
 	bool res = false;
 	DC_LOGGER_INIT(pipe_ctx->stream->ctx->logger);
 
+	/* Invalid input */
+	if (!plane_state ||
+			!plane_state->dst_rect.width ||
+			!plane_state->dst_rect.height ||
+			!plane_state->src_rect.width ||
+			!plane_state->src_rect.height) {
+		ASSERT(0);
+		return false;
+	}
+
 	pipe_ctx->plane_res.scl_data.format = convert_pixel_format_to_dalsurface(
 			pipe_ctx->plane_state->format);
 
@@ -1062,12 +1073,13 @@
 	 * on certain displays, such as the Sharp 4k. 36bpp is needed
 	 * to support SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616 and
 	 * SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 with actual > 10 bpc
-	 * precision on at least DCN display engines. However, at least
-	 * Carrizo with DCE_VERSION_11_0 does not like 36 bpp lb depth,
-	 * so use only 30 bpp on DCE_VERSION_11_0. Testing with DCE 11.2 and 8.3
-	 * did not show such problems, so this seems to be the exception.
+	 * precision on DCN display engines, but apparently not for DCE, as
+	 * far as testing on DCE-11.2 and DCE-8 showed. Various DCE parts have
+	 * problems: Carrizo with DCE_VERSION_11_0 does not like 36 bpp lb depth,
+	 * neither do DCE-8 at 4k resolution, or DCE-11.2 (broken identify pixel
+	 * passthrough). Therefore only use 36 bpp on DCN where it is actually needed.
 	 */
-	if (plane_state->ctx->dce_version > DCE_VERSION_11_0)
+	if (plane_state->ctx->dce_version > DCE_VERSION_MAX)
 		pipe_ctx->plane_res.scl_data.lb_params.depth = LB_PIXEL_DEPTH_36BPP;
 	else
 		pipe_ctx->plane_res.scl_data.lb_params.depth = LB_PIXEL_DEPTH_30BPP;
@@ -1433,6 +1445,9 @@
 	struct dc_stream_status *stream_status = NULL;
 	struct resource_pool *pool = dc->res_pool;
 
+	if (!plane_state)
+		return true;
+
 	for (i = 0; i < context->stream_count; i++)
 		if (context->streams[i] == stream) {
 			stream_status = &context->stream_status[i];
@@ -1599,6 +1614,9 @@
 	if (is_timing_changed(stream_a, stream_b))
 		return false;
 
+	if (stream_a->signal != stream_b->signal)
+		return false;
+
 	if (stream_a->dpms_off != stream_b->dpms_off)
 		return false;
 
@@ -1616,6 +1634,8 @@
 bool dc_is_stream_unchanged(
 	struct dc_stream_state *old_stream, struct dc_stream_state *stream)
 {
+	if (!old_stream || !stream)
+		return false;
 
 	if (!are_stream_backends_same(old_stream, stream))
 		return false;
@@ -1623,6 +1643,10 @@
 	if (old_stream->ignore_msa_timing_param != stream->ignore_msa_timing_param)
 		return false;
 
+	/*compare audio info*/
+	if (memcmp(&old_stream->audio_info, &stream->audio_info, sizeof(stream->audio_info)) != 0)
+		return false;
+
 	return true;
 }
 
@@ -1717,6 +1741,9 @@
 {
 	int i, available_audio_count;
 
+	if (id == ENGINE_ID_UNKNOWN)
+		return NULL;
+
 	available_audio_count = pool->audio_count;
 
 	for (i = 0; i < available_audio_count; i++) {
@@ -1795,9 +1822,6 @@
 				dc->res_pool,
 			del_pipe->stream_res.stream_enc,
 			false);
-	/* Release link encoder from stream in new dc_state. */
-	if (dc->res_pool->funcs->link_enc_unassign)
-		dc->res_pool->funcs->link_enc_unassign(new_ctx, del_pipe->stream);
 
 	if (del_pipe->stream_res.audio)
 		update_audio_usage(
@@ -1888,10 +1912,13 @@
 			break;
 		case COLOR_DEPTH_121212:
 			normalized_pix_clk = (pix_clk * 36) / 24;
-		break;
+			break;
+		case COLOR_DEPTH_141414:
+			normalized_pix_clk = (pix_clk * 42) / 24;
+			break;
 		case COLOR_DEPTH_161616:
 			normalized_pix_clk = (pix_clk * 48) / 24;
-		break;
+			break;
 		default:
 			ASSERT(0);
 		break;
@@ -2113,6 +2140,9 @@
 		struct dc_state *dst_ctx)
 {
 	dst_ctx->clk_mgr = dc->clk_mgr;
+
+	/* Initialise DIG link encoder resource tracking variables. */
+	link_enc_cfg_init(dc, dst_ctx);
 }
 
 
@@ -2141,16 +2171,6 @@
 
 	if (!new_ctx)
 		return DC_ERROR_UNEXPECTED;
-#if defined(CONFIG_DRM_AMD_DC_DCN)
-
-	/*
-	 * Update link encoder to stream assignment.
-	 * TODO: Split out reason allocation from validation.
-	 */
-	if (dc->res_pool->funcs->link_encs_assign)
-		dc->res_pool->funcs->link_encs_assign(
-			dc, new_ctx, new_ctx->streams, new_ctx->stream_count);
-#endif
 
 	if (dc->res_pool->funcs->validate_global) {
 		result = dc->res_pool->funcs->validate_global(dc, new_ctx);
@@ -2202,6 +2222,16 @@
 		if (!dc->res_pool->funcs->validate_bandwidth(dc, new_ctx, fast_validate))
 			result = DC_FAIL_BANDWIDTH_VALIDATE;
 
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+	/*
+	 * Only update link encoder to stream assignment after bandwidth validation passed.
+	 * TODO: Split out assignment and validation.
+	 */
+	if (result == DC_OK && dc->res_pool->funcs->link_encs_assign && fast_validate == false)
+		dc->res_pool->funcs->link_encs_assign(
+			dc, new_ctx, new_ctx->streams, new_ctx->stream_count);
+#endif
+
 	return result;
 }
 
@@ -2727,8 +2757,18 @@
 		return true;
 
 	/* DIG link encoder resource assignment for stream changed. */
-	if (pipe_ctx_old->stream->link_enc != pipe_ctx->stream->link_enc)
-		return true;
+	if (pipe_ctx_old->stream->ctx->dc->res_pool->funcs->link_encs_assign) {
+		bool need_reprogram = false;
+		struct dc *dc = pipe_ctx_old->stream->ctx->dc;
+		enum link_enc_cfg_mode mode = dc->current_state->res_ctx.link_enc_cfg_ctx.mode;
+
+		dc->current_state->res_ctx.link_enc_cfg_ctx.mode = LINK_ENC_CFG_STEADY;
+		if (link_enc_cfg_get_link_enc_used_by_stream(dc, pipe_ctx_old->stream) != pipe_ctx->stream->link_enc)
+			need_reprogram = true;
+		dc->current_state->res_ctx.link_enc_cfg_ctx.mode = mode;
+
+		return need_reprogram;
+	}
 
 	return false;
 }
@@ -2871,7 +2911,8 @@
 		res = DC_FAIL_CONTROLLER_VALIDATE;
 
 	if (res == DC_OK) {
-		if (!link->link_enc->funcs->validate_output_with_stream(
+		if (link->ep_type == DISPLAY_ENDPOINT_PHY &&
+				!link->link_enc->funcs->validate_output_with_stream(
 						link->link_enc, stream))
 			res = DC_FAIL_ENC_VALIDATE;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_stat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_stat.c
@@ -61,6 +61,14 @@
 
 	status = dmub_srv_stat_get_notification(dmub, notify);
 	ASSERT(status == DMUB_STATUS_OK);
+
+	/* For HPD/HPD RX, convert dpia port index into link index */
+	if (notify->type == DMUB_NOTIFICATION_HPD ||
+	    notify->type == DMUB_NOTIFICATION_HPD_IRQ ||
+	    notify->type == DMUB_NOTIFICATION_SET_CONFIG_REPLY) {
+		notify->link_index =
+			get_link_index_from_dpia_port_index(dc, notify->link_index);
+	}
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_stream.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_stream.c
@@ -562,7 +562,7 @@
 	for (i = 0; i < MAX_PIPES; i++) {
 		struct timing_generator *tg = res_ctx->pipe_ctx[i].stream_res.tg;
 
-		if (res_ctx->pipe_ctx[i].stream != stream)
+		if (res_ctx->pipe_ctx[i].stream != stream || !tg)
 			continue;
 
 		return tg->funcs->get_frame_count(tg);
@@ -621,7 +621,7 @@
 	for (i = 0; i < MAX_PIPES; i++) {
 		struct timing_generator *tg = res_ctx->pipe_ctx[i].stream_res.tg;
 
-		if (res_ctx->pipe_ctx[i].stream != stream)
+		if (res_ctx->pipe_ctx[i].stream != stream || !tg)
 			continue;
 
 		tg->funcs->get_scanoutpos(tg,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/core/dc_surface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/core/dc_surface.c
@@ -154,7 +154,8 @@
 		if (pipe_ctx->plane_state != plane_state)
 			continue;
 
-		pipe_ctx->plane_state->status.is_flip_pending = false;
+		if (pipe_ctx->plane_state)
+			pipe_ctx->plane_state->status.is_flip_pending = false;
 
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dc.h
@@ -44,10 +44,12 @@
 
 /* forward declaration */
 struct aux_payload;
+struct set_config_cmd_payload;
+struct dmub_notification;
 
 #define DC_VER "3.2.149"
 
-#define MAX_SURFACES 3
+#define MAX_SURFACES 4
 #define MAX_PLANES 6
 #define MAX_STREAMS 6
 #define MAX_SINKS_PER_LINK 4
@@ -164,6 +166,11 @@
 	uint32_t dmdata_alloc_size;
 	unsigned int max_cursor_size;
 	unsigned int max_video_width;
+	/*
+	 * max video plane width that can be safely assumed to be always
+	 * supported by single DPP pipe.
+	 */
+	unsigned int max_optimizable_video_width;
 	unsigned int min_horizontal_blanking_period;
 	int linear_pitch_alignment;
 	bool dcc_const_color;
@@ -185,6 +192,7 @@
 	struct dc_color_caps color;
 	bool vbios_lttpr_aware;
 	bool vbios_lttpr_enable;
+	uint32_t max_otg_num;
 };
 
 struct dc_bug_wa {
@@ -460,6 +468,17 @@
 	uint32_t u32All;
 };
 
+union dpia_debug_options {
+	struct {
+		uint32_t disable_dpia:1;
+		uint32_t force_non_lttpr:1;
+		uint32_t extend_aux_rd_interval:1;
+		uint32_t disable_mst_dsc_work_around:1;
+		uint32_t reserved:28;
+	} bits;
+	uint32_t raw;
+};
+
 struct dc_debug_data {
 	uint32_t ltFailCount;
 	uint32_t i2cErrorCount;
@@ -624,9 +643,11 @@
 	bool force_enable_edp_fec;
 	/* FEC/PSR1 sequence enable delay in 100us */
 	uint8_t fec_enable_delay_in100us;
+	bool enable_driver_sequence_debug;
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 	bool disable_z10;
 	bool enable_sw_cntl_psr;
+	union dpia_debug_options dpia_debug;
 #endif
 };
 
@@ -1145,6 +1166,7 @@
 	struct dpcd_dsc_capabilities dsc_caps;
 	struct dc_lttpr_caps lttpr_caps;
 	struct psr_caps psr_caps;
+	struct dpcd_usb4_dp_tunneling_info usb4_dp_tun_info;
 
 };
 
@@ -1341,12 +1363,29 @@
 void dc_z10_save_init(struct dc *dc);
 #endif
 
+bool dc_is_dmub_outbox_supported(struct dc *dc);
 bool dc_enable_dmub_notifications(struct dc *dc);
 
+void dc_enable_dmub_outbox(struct dc *dc);
+
 bool dc_process_dmub_aux_transfer_async(struct dc *dc,
 				uint32_t link_index,
 				struct aux_payload *payload);
 
+/* Get dc link index from dpia port index */
+uint8_t get_link_index_from_dpia_port_index(const struct dc *dc,
+				uint8_t dpia_port_index);
+
+bool dc_process_dmub_set_config_async(struct dc *dc,
+				uint32_t link_index,
+				struct set_config_cmd_payload *payload,
+				struct dmub_notification *notify);
+
+enum dc_status dc_process_dmub_set_mst_slots(const struct dc *dc,
+				uint32_t link_index,
+				uint8_t mst_alloc_slots,
+				uint8_t *mst_slots_in_use);
+
 /*******************************************************************************
  * DSC Interfaces
  ******************************************************************************/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dc_dp_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dc_dp_types.h
@@ -109,7 +109,6 @@
 	enum dc_link_spread link_spread;
 	bool use_link_rate_set;
 	uint8_t link_rate_set;
-	bool dpcd_source_device_specific_field_support;
 };
 
 struct dc_lane_settings {
@@ -758,4 +757,35 @@
 	bool psr_exit_link_training_required;
 };
 
+/* Length of router topology ID read from DPCD in bytes. */
+#define DPCD_USB4_TOPOLOGY_ID_LEN 5
+
+/* DPCD[0xE000D] DP_TUNNELING_CAPABILITIES SUPPORT register. */
+union dp_tun_cap_support {
+	struct {
+		uint8_t dp_tunneling :1;
+		uint8_t rsvd :5;
+		uint8_t panel_replay_tun_opt :1;
+		uint8_t dpia_bw_alloc :1;
+	} bits;
+	uint8_t raw;
+};
+
+/* DPCD[0xE000E] DP_IN_ADAPTER_INFO register. */
+union dpia_info {
+	struct {
+		uint8_t dpia_num :5;
+		uint8_t rsvd :3;
+	} bits;
+	uint8_t raw;
+};
+
+/* DP Tunneling over USB4 */
+struct dpcd_usb4_dp_tunneling_info {
+	union dp_tun_cap_support dp_tun_cap;
+	union dpia_info dpia_info;
+	uint8_t usb4_driver_id;
+	uint8_t usb4_topology_id[DPCD_USB4_TOPOLOGY_ID_LEN];
+};
+
 #endif /* DC_DP_TYPES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dc_link.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dc_link.h
@@ -175,6 +175,8 @@
 		bool dp_keep_receiver_powered;
 		bool dp_skip_DID2;
 		bool dp_skip_reset_segment;
+		/* Some USB4 docks do not handle turning off MST DSC once it has been enabled. */
+		bool dpia_mst_dsc_always_on;
 	} wa_flags;
 	struct link_mst_stream_allocation_table mst_stream_alloc_table;
 
@@ -271,6 +273,10 @@
 
 void dc_link_get_psr_residency(const struct dc_link *link, uint32_t *residency);
 
+void dc_link_blank_all_dp_displays(struct dc *dc);
+
+void dc_link_blank_dp_stream(struct dc_link *link, bool hw_init);
+
 /* Request DC to detect if there is a Panel connected.
  * boot - If this call is during initial boot.
  * Return false for any type of detection failure or MST detection
@@ -296,7 +302,8 @@
  * false - no change in Downstream port status. No further action required
  * from DM. */
 bool dc_link_handle_hpd_rx_irq(struct dc_link *dc_link,
-		union hpd_irq_data *hpd_irq_dpcd_data, bool *out_link_loss);
+		union hpd_irq_data *hpd_irq_dpcd_data, bool *out_link_loss,
+		bool defer_handling, bool *has_left_work);
 
 /*
  * On eDP links this function call will stall until T12 has elapsed.
@@ -305,9 +312,9 @@
  */
 bool dc_link_wait_for_t12(struct dc_link *link);
 
-enum dc_status read_hpd_rx_irq_data(
-	struct dc_link *link,
-	union hpd_irq_data *irq_data);
+void dc_link_dp_handle_automated_test(struct dc_link *link);
+void dc_link_dp_handle_link_loss(struct dc_link *link);
+bool dc_link_dp_allow_hpd_rx_irq(const struct dc_link *link);
 
 struct dc_sink_init_data;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dc_stream.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dc_stream.h
@@ -193,8 +193,7 @@
 	/* DMCU info */
 	unsigned int abm_level;
 
-	struct periodic_interrupt_config periodic_interrupt0;
-	struct periodic_interrupt_config periodic_interrupt1;
+	struct periodic_interrupt_config periodic_interrupt;
 
 	/* from core_stream struct */
 	struct dc_context *ctx;
@@ -260,8 +259,7 @@
 	struct dc_info_packet *hdr_static_metadata;
 	unsigned int *abm_level;
 
-	struct periodic_interrupt_config *periodic_interrupt0;
-	struct periodic_interrupt_config *periodic_interrupt1;
+	struct periodic_interrupt_config *periodic_interrupt;
 
 	struct dc_info_packet *vrr_infopacket;
 	struct dc_info_packet *vsc_infopacket;
@@ -290,6 +288,9 @@
 	struct dc_stream_state *old_stream, struct dc_stream_state *stream);
 
 /*
+ * Setup stream attributes if no stream updates are provided
+ * there will be no impact on the stream parameters
+ *
  * Set up surface attributes and associate to a stream
  * The surfaces parameter is an absolute set of all surface active for the stream.
  * If no surfaces are provided, the stream will be blanked; no memory read.
@@ -298,8 +299,23 @@
  * After this call:
  *   Surfaces attributes are programmed and configured to be composed into stream.
  *   This does not trigger a flip.  No surface address is programmed.
+ *
  */
+bool dc_update_planes_and_stream(struct dc *dc,
+		struct dc_surface_update *surface_updates, int surface_count,
+		struct dc_stream_state *dc_stream,
+		struct dc_stream_update *stream_update);
 
+/*
+ * Set up surface attributes and associate to a stream
+ * The surfaces parameter is an absolute set of all surface active for the stream.
+ * If no surfaces are provided, the stream will be blanked; no memory read.
+ * Any flip related attribute changes must be done through this interface.
+ *
+ * After this call:
+ *   Surfaces attributes are programmed and configured to be composed into stream.
+ *   This does not trigger a flip.  No surface address is programmed.
+ */
 void dc_commit_updates_for_stream(struct dc *dc,
 		struct dc_surface_update *srf_updates,
 		int surface_count,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dc_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dc_types.h
@@ -934,6 +934,7 @@
 /* Possible values of display_endpoint_id.endpoint */
 enum display_endpoint_type {
 	DISPLAY_ENDPOINT_PHY = 0, /* Physical connector. */
+	DISPLAY_ENDPOINT_USB4_DPIA, /* USB4 DisplayPort tunnel. */
 	DISPLAY_ENDPOINT_UNKNOWN = -1
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce/dce_aux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce/dce_aux.c
@@ -627,6 +627,7 @@
 #define AUX_MAX_I2C_DEFER_RETRIES 7
 #define AUX_MAX_INVALID_REPLY_RETRIES 2
 #define AUX_MAX_TIMEOUT_RETRIES 3
+#define AUX_DEFER_DELAY_FOR_DPIA 4 /*ms*/
 
 static void dce_aux_log_payload(const char *payload_name,
 	unsigned char *payload, uint32_t length, uint32_t max_length_to_log)
@@ -765,7 +766,10 @@
 							"dce_aux_transfer_with_retries: AUX_RET_SUCCESS: AUX_TRANSACTION_REPLY_AUX_DEFER");
 
 				/* polling_timeout_period is in us */
-				defer_time_in_ms += aux110->polling_timeout_period / 1000;
+				if (aux110)
+					defer_time_in_ms += aux110->polling_timeout_period / 1000;
+				else
+					defer_time_in_ms += AUX_DEFER_DELAY_FOR_DPIA;
 				++aux_defer_retries;
 				fallthrough;
 			case AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce/dce_clock_source.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce/dce_clock_source.c
@@ -545,9 +545,11 @@
 		switch (pix_clk_params->color_depth) {
 		case COLOR_DEPTH_101010:
 			actual_pixel_clock_100hz = (actual_pixel_clock_100hz * 5) >> 2;
+			actual_pixel_clock_100hz -= actual_pixel_clock_100hz % 10;
 			break;
 		case COLOR_DEPTH_121212:
 			actual_pixel_clock_100hz = (actual_pixel_clock_100hz * 6) >> 2;
+			actual_pixel_clock_100hz -= actual_pixel_clock_100hz % 10;
 			break;
 		case COLOR_DEPTH_161616:
 			actual_pixel_clock_100hz = actual_pixel_clock_100hz * 2;
@@ -1013,9 +1015,12 @@
 			 * not be programmed equal to DPREFCLK
 			 */
 			modulo_hz = REG_READ(MODULO[inst]);
-			*pixel_clk_khz = div_u64((uint64_t)clock_hz*
-				clock_source->ctx->dc->clk_mgr->dprefclk_khz*10,
-				modulo_hz);
+			if (modulo_hz)
+				*pixel_clk_khz = div_u64((uint64_t)clock_hz*
+					clock_source->ctx->dc->clk_mgr->dprefclk_khz*10,
+					modulo_hz);
+			else
+				*pixel_clk_khz = 0;
 		} else {
 			/* NOTE: There is agreement with VBIOS here that MODULO is
 			 * programmed equal to DPREFCLK, in which case PHASE will be
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce/dce_stream_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce/dce_stream_encoder.c
@@ -919,6 +919,7 @@
 }
 
 static void dce110_stream_encoder_dp_blank(
+	struct dc_link *link,
 	struct stream_encoder *enc)
 {
 	struct dce110_stream_encoder *enc110 = DCE110STRENC_FROM_STRENC(enc);
@@ -967,6 +968,7 @@
 
 /* output video stream to link encoder */
 static void dce110_stream_encoder_dp_unblank(
+	struct dc_link *link,
 	struct stream_encoder *enc,
 	const struct encoder_unblank_param *param)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce/dce_transform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce/dce_transform.c
@@ -1009,7 +1009,7 @@
 		color_depth = COLOR_DEPTH_101010;
 		pixel_depth = 0;
 		expan_mode  = 1;
-		BREAK_TO_DEBUGGER();
+		DC_LOG_DC("The pixel depth %d is not valid, set COLOR_DEPTH_101010 instead.", depth);
 		break;
 	}
 
@@ -1023,8 +1023,7 @@
 	if (!(xfm_dce->lb_pixel_depth_supported & depth)) {
 		/*we should use unsupported capabilities
 		 *  unless it is required by w/a*/
-		DC_LOG_WARNING("%s: Capability not supported",
-			__func__);
+		DC_LOG_DC("%s: Capability not supported", __func__);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce/dmub_outbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce/dmub_outbox.c
@@ -22,20 +22,23 @@
  * Authors: AMD
  */
 
-#include "dmub_outbox.h"
+#include "dc.h"
 #include "dc_dmub_srv.h"
+#include "dmub_outbox.h"
 #include "dmub/inc/dmub_cmd.h"
 
-/**
- *  dmub_enable_outbox_notification - Sends inbox cmd to dmub to enable outbox1
- *                                    messages with interrupt. Dmub sends outbox1
- *                                    message and triggers outbox1 interrupt.
- * @dc: dc structure
+/*
+ *  Function: dmub_enable_outbox_notification
+ *
+ *  @brief
+ *		Sends inbox cmd to dmub for enabling outbox notifications to x86.
+ *
+ *  @param
+ *		[in] dmub_srv: dmub_srv structure
  */
-void dmub_enable_outbox_notification(struct dc *dc)
+void dmub_enable_outbox_notification(struct dc_dmub_srv *dmub_srv)
 {
 	union dmub_rb_cmd cmd;
-	struct dc_context *dc_ctx = dc->ctx;
 
 	memset(&cmd, 0x0, sizeof(cmd));
 	cmd.outbox1_enable.header.type = DMUB_CMD__OUTBOX1_ENABLE;
@@ -45,7 +48,7 @@
 		sizeof(cmd.outbox1_enable.header);
 	cmd.outbox1_enable.enable = true;
 
-	dc_dmub_srv_cmd_queue(dc_ctx->dmub_srv, &cmd);
-	dc_dmub_srv_cmd_execute(dc_ctx->dmub_srv);
-	dc_dmub_srv_wait_idle(dc_ctx->dmub_srv);
+	dc_dmub_srv_cmd_queue(dmub_srv, &cmd);
+	dc_dmub_srv_cmd_execute(dmub_srv);
+	dc_dmub_srv_wait_idle(dmub_srv);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce/dmub_outbox.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce/dmub_outbox.h
@@ -26,8 +26,8 @@
 #ifndef _DMUB_OUTBOX_H_
 #define _DMUB_OUTBOX_H_
 
-#include "dc.h"
+struct dc_dmub_srv;
 
-void dmub_enable_outbox_notification(struct dc *dc);
+void dmub_enable_outbox_notification(struct dc_dmub_srv *dmub_srv);
 
 #endif /* _DMUB_OUTBOX_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
@@ -46,6 +46,7 @@
 #include "transform.h"
 #include "stream_encoder.h"
 #include "link_encoder.h"
+#include "link_enc_cfg.h"
 #include "link_hwss.h"
 #include "dc_link_dp.h"
 #if defined(CONFIG_DRM_AMD_DC_DCN)
@@ -57,7 +58,8 @@
 #include "audio.h"
 #include "reg_helper.h"
 #include "panel_cntl.h"
-
+#include "inc/link_dpcd.h"
+#include "dpcd_defs.h"
 /* include DCE11 register header files */
 #include "dce/dce_11_0_d.h"
 #include "dce/dce_11_0_sh_mask.h"
@@ -980,7 +982,9 @@
 		return;
 	}
 
-	if (link->panel_cntl) {
+	if (link->panel_cntl && !(link->dpcd_sink_ext_caps.bits.oled ||
+		link->dpcd_sink_ext_caps.bits.hdr_aux_backlight_control == 1 ||
+		link->dpcd_sink_ext_caps.bits.sdr_aux_backlight_control == 1)) {
 		bool is_backlight_on = link->panel_cntl->funcs->is_panel_backlight_on(link->panel_cntl);
 
 		if ((enable && is_backlight_on) || (!enable && !is_backlight_on)) {
@@ -1113,6 +1117,9 @@
 		if (pipe_ctx->stream_res.audio)
 			pipe_ctx->stream_res.audio->enabled = true;
 	}
+
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(pipe_ctx->stream->link, DPCD_SOURCE_SEQ_AFTER_ENABLE_AUDIO_STREAM);
 }
 
 void dce110_disable_audio_stream(struct pipe_ctx *pipe_ctx)
@@ -1151,6 +1158,9 @@
 		 * stream->stream_engine_id);
 		 */
 	}
+
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(pipe_ctx->stream->link, DPCD_SOURCE_SEQ_AFTER_DISABLE_AUDIO_STREAM);
 }
 
 void dce110_disable_stream(struct pipe_ctx *pipe_ctx)
@@ -1158,6 +1168,7 @@
 	struct dc_stream_state *stream = pipe_ctx->stream;
 	struct dc_link *link = stream->link;
 	struct dc *dc = pipe_ctx->stream->ctx->dc;
+	struct link_encoder *link_enc = NULL;
 
 	if (dc_is_hdmi_tmds_signal(pipe_ctx->stream->signal)) {
 		pipe_ctx->stream_res.stream_enc->funcs->stop_hdmi_info_packets(
@@ -1172,11 +1183,21 @@
 
 	dc->hwss.disable_audio_stream(pipe_ctx);
 
-	link->link_enc->funcs->connect_dig_be_to_fe(
+	/* Link encoder may have been dynamically assigned to non-physical display endpoint. */
+	if (link->ep_type == DISPLAY_ENDPOINT_PHY)
+		link_enc = link->link_enc;
+	else if (dc->res_pool->funcs->link_encs_assign)
+		link_enc = link_enc_cfg_get_link_enc_used_by_link(link->ctx->dc, link);
+	ASSERT(link_enc);
+
+	if (link_enc)
+		link_enc->funcs->connect_dig_be_to_fe(
 			link->link_enc,
 			pipe_ctx->stream_res.stream_enc->id,
 			false);
 
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_DISCONNECT_DIG_FE_BE);
 }
 
 void dce110_unblank_stream(struct pipe_ctx *pipe_ctx,
@@ -1192,7 +1213,7 @@
 	params.link_settings.link_rate = link_settings->link_rate;
 
 	if (dc_is_dp_signal(pipe_ctx->stream->signal))
-		pipe_ctx->stream_res.stream_enc->funcs->dp_unblank(pipe_ctx->stream_res.stream_enc, &params);
+		pipe_ctx->stream_res.stream_enc->funcs->dp_unblank(link, pipe_ctx->stream_res.stream_enc, &params);
 
 	if (link->local_sink && link->local_sink->sink_signal == SIGNAL_TYPE_EDP) {
 		hws->funcs.edp_backlight_control(link, true);
@@ -1211,7 +1232,7 @@
 	}
 
 	if (dc_is_dp_signal(pipe_ctx->stream->signal)) {
-		pipe_ctx->stream_res.stream_enc->funcs->dp_blank(pipe_ctx->stream_res.stream_enc);
+		pipe_ctx->stream_res.stream_enc->funcs->dp_blank(link, pipe_ctx->stream_res.stream_enc);
 
 		if (!dc_is_embedded_signal(pipe_ctx->stream->signal)) {
 			/*
@@ -1436,6 +1457,7 @@
 		struct dc *dc)
 {
 	struct dc_stream_state *stream = pipe_ctx->stream;
+	struct dc_link *link = stream->link;
 	struct drr_params params = {0};
 	unsigned int event_triggers = 0;
 	struct pipe_ctx *odm_pipe = pipe_ctx->next_odm_pipe;
@@ -1499,6 +1521,9 @@
 			pipe_ctx->stream_res.stream_enc,
 			pipe_ctx->stream_res.tg->inst);
 
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_CONNECT_DIG_FE_OTG);
+
 	pipe_ctx->stream_res.opp->funcs->opp_set_dyn_expansion(
 			pipe_ctx->stream_res.opp,
 			COLOR_SPACE_YCBCR601,
@@ -1539,27 +1564,17 @@
 {
 	int i;
 
-	/* do not know BIOS back-front mapping, simply blank all. It will not
-	 * hurt for non-DP
-	 */
-	for (i = 0; i < dc->res_pool->stream_enc_count; i++) {
-		dc->res_pool->stream_enc[i]->funcs->dp_blank(
-					dc->res_pool->stream_enc[i]);
-	}
-
 	for (i = 0; i < dc->link_count; i++) {
 		enum signal_type signal = dc->links[i]->connector_signal;
 
-		if ((signal == SIGNAL_TYPE_EDP) ||
-			(signal == SIGNAL_TYPE_DISPLAY_PORT))
-			if (!dc->links[i]->wa_flags.dp_keep_receiver_powered)
-				dp_receiver_power_ctrl(dc->links[i], false);
+		dc_link_blank_dp_stream(dc->links[i], false);
 
 		if (signal != SIGNAL_TYPE_EDP)
 			signal = SIGNAL_TYPE_NONE;
 
-		dc->links[i]->link_enc->funcs->disable_output(
-				dc->links[i]->link_enc, signal);
+		if (dc->links[i]->ep_type == DISPLAY_ENDPOINT_PHY)
+			dc->links[i]->link_enc->funcs->disable_output(
+					dc->links[i]->link_enc, signal);
 
 		dc->links[i]->link_status.link_active = false;
 		memset(&dc->links[i]->cur_link_settings, 0,
@@ -1744,10 +1759,13 @@
 			hws->funcs.edp_backlight_control(edp_link_with_sink, false);
 		}
 		/*resume from S3, no vbios posting, no need to power down again*/
+		clk_mgr_exit_optimized_pwr_state(dc, dc->clk_mgr);
+
 		power_down_all_hw_blocks(dc);
 		disable_vga_and_power_gate_all_controllers(dc);
 		if (edp_link_with_sink && !keep_edp_vdd_on)
 			dc->hwss.edp_power_control(edp_link_with_sink, false);
+		clk_mgr_optimize_pwr_state(dc, dc->clk_mgr);
 	}
 	bios_set_scratch_acc_mode_change(dc->ctx->dc_bios, 1);
 }
@@ -2108,7 +2126,8 @@
 			continue;
 		if (pipe_ctx->stream->signal != SIGNAL_TYPE_HDMI_TYPE_A)
 			continue;
-		if (pipe_ctx->stream_res.audio != NULL) {
+		if (pipe_ctx->stream_res.audio != NULL &&
+			pipe_ctx->stream_res.audio->enabled == false) {
 			struct audio_output audio_output;
 
 			build_audio_output(context, pipe_ctx, &audio_output);
@@ -2156,7 +2175,8 @@
 			if (!dc_is_dp_signal(pipe_ctx->stream->signal))
 				continue;
 
-			if (pipe_ctx->stream_res.audio != NULL) {
+			if (pipe_ctx->stream_res.audio != NULL &&
+				pipe_ctx->stream_res.audio->enabled == false) {
 				struct audio_output audio_output;
 
 				build_audio_output(context, pipe_ctx, &audio_output);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce120/dce120_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce120/dce120_resource.c
@@ -361,7 +361,8 @@
 	audio_regs(2),
 	audio_regs(3),
 	audio_regs(4),
-	audio_regs(5)
+	audio_regs(5),
+	audio_regs(6),
 };
 
 #define DCE120_AUD_COMMON_MASK_SH_LIST(mask_sh)\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce60/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce60/Makefile
@@ -23,7 +23,7 @@
 # Makefile for the 'controller' sub-component of DAL.
 # It provides the control and status of HW CRTC block.
 
-CFLAGS_AMDDALPATH)/dc/dce60/dce60_resource.o = $(call cc-disable-warning, override-init)
+CFLAGS_$(AMDDALPATH)/dc/dce60/dce60_resource.o = $(call cc-disable-warning, override-init)
 
 DCE60 = dce60_timing_generator.o dce60_hw_sequencer.o \
 	dce60_resource.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce60/dce60_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce60/dce60_resource.c
@@ -1127,6 +1127,7 @@
 	if (dce60_construct(num_virtual_links, dc, pool))
 		return &pool->base;
 
+	kfree(pool);
 	BREAK_TO_DEBUGGER();
 	return NULL;
 }
@@ -1324,6 +1325,7 @@
 	if (dce61_construct(num_virtual_links, dc, pool))
 		return &pool->base;
 
+	kfree(pool);
 	BREAK_TO_DEBUGGER();
 	return NULL;
 }
@@ -1517,6 +1519,7 @@
 	if (dce64_construct(num_virtual_links, dc, pool))
 		return &pool->base;
 
+	kfree(pool);
 	BREAK_TO_DEBUGGER();
 	return NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dce80/dce80_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dce80/dce80_resource.c
@@ -1138,6 +1138,7 @@
 	if (dce80_construct(num_virtual_links, dc, pool))
 		return &pool->base;
 
+	kfree(pool);
 	BREAK_TO_DEBUGGER();
 	return NULL;
 }
@@ -1337,6 +1338,7 @@
 	if (dce81_construct(num_virtual_links, dc, pool))
 		return &pool->base;
 
+	kfree(pool);
 	BREAK_TO_DEBUGGER();
 	return NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_cm_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_cm_common.c
@@ -379,6 +379,11 @@
 				i += increment) {
 			if (j == hw_points - 1)
 				break;
+			if (i >= TRANSFER_FUNC_POINTS) {
+				DC_LOG_ERROR("Index out of bounds: i=%d, TRANSFER_FUNC_POINTS=%d\n",
+					     i, TRANSFER_FUNC_POINTS);
+				return false;
+			}
 			rgb_resulted[j].red = output_tf->tf_pts.red[i];
 			rgb_resulted[j].green = output_tf->tf_pts.green[i];
 			rgb_resulted[j].blue = output_tf->tf_pts.blue[i];
@@ -555,6 +560,8 @@
 				i += increment) {
 			if (j == hw_points - 1)
 				break;
+			if (i >= TRANSFER_FUNC_POINTS)
+				return false;
 			rgb_resulted[j].red = output_tf->tf_pts.red[i];
 			rgb_resulted[j].green = output_tf->tf_pts.green[i];
 			rgb_resulted[j].blue = output_tf->tf_pts.blue[i];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c
@@ -940,6 +940,7 @@
 	.program_watermarks = hubbub1_program_watermarks,
 	.is_allow_self_refresh_enabled = hubbub1_is_allow_self_refresh_enabled,
 	.allow_self_refresh_control = hubbub1_allow_self_refresh_control,
+	.verify_allow_pstate_change_high = hubbub1_verify_allow_pstate_change_high,
 };
 
 void hubbub1_construct(struct hubbub *hubbub,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c
@@ -804,6 +804,32 @@
 		tg->funcs->clear_optc_underflow(tg);
 }
 
+static int calculate_vready_offset_for_group(struct pipe_ctx *pipe)
+{
+	struct pipe_ctx *other_pipe;
+	int vready_offset = pipe->pipe_dlg_param.vready_offset;
+
+	/* Always use the largest vready_offset of all connected pipes */
+	for (other_pipe = pipe->bottom_pipe; other_pipe != NULL; other_pipe = other_pipe->bottom_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+	for (other_pipe = pipe->top_pipe; other_pipe != NULL; other_pipe = other_pipe->top_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+	for (other_pipe = pipe->next_odm_pipe; other_pipe != NULL; other_pipe = other_pipe->next_odm_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+	for (other_pipe = pipe->prev_odm_pipe; other_pipe != NULL; other_pipe = other_pipe->prev_odm_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+
+	return vready_offset;
+}
+
 enum dc_status dcn10_enable_stream_timing(
 		struct pipe_ctx *pipe_ctx,
 		struct dc_state *context,
@@ -838,7 +864,7 @@
 	pipe_ctx->stream_res.tg->funcs->program_timing(
 			pipe_ctx->stream_res.tg,
 			&stream->timing,
-			pipe_ctx->pipe_dlg_param.vready_offset,
+			calculate_vready_offset_for_group(pipe_ctx),
 			pipe_ctx->pipe_dlg_param.vstartup_start,
 			pipe_ctx->pipe_dlg_param.vupdate_offset,
 			pipe_ctx->pipe_dlg_param.vupdate_width,
@@ -1052,9 +1078,13 @@
 
 void dcn10_verify_allow_pstate_change_high(struct dc *dc)
 {
+	struct hubbub *hubbub = dc->res_pool->hubbub;
 	static bool should_log_hw_state; /* prevent hw state log by default */
 
-	if (!hubbub1_verify_allow_pstate_change_high(dc->res_pool->hubbub)) {
+	if (!hubbub->funcs->verify_allow_pstate_change_high)
+		return;
+
+	if (!hubbub->funcs->verify_allow_pstate_change_high(hubbub)) {
 		int i = 0;
 
 		if (should_log_hw_state)
@@ -1063,8 +1093,8 @@
 		TRACE_DC_PIPE_STATE(pipe_ctx, i, MAX_PIPES);
 		BREAK_TO_DEBUGGER();
 		if (dcn10_hw_wa_force_recovery(dc)) {
-		/*check again*/
-			if (!hubbub1_verify_allow_pstate_change_high(dc->res_pool->hubbub))
+			/*check again*/
+			if (!hubbub->funcs->verify_allow_pstate_change_high(hubbub))
 				BREAK_TO_DEBUGGER();
 		}
 	}
@@ -1301,7 +1331,7 @@
 
 void dcn10_init_hw(struct dc *dc)
 {
-	int i, j;
+	int i;
 	struct abm *abm = dc->res_pool->abm;
 	struct dmcu *dmcu = dc->res_pool->dmcu;
 	struct dce_hwseq *hws = dc->hwseq;
@@ -1392,48 +1422,12 @@
 				hws->funcs.dsc_pg_control(hws, res_pool->dscs[i]->inst, false);
 	}
 
-	/* Enable outbox notification feature of dmub */
-	if (dc->debug.enable_dmub_aux_for_legacy_ddc)
-		dmub_enable_outbox_notification(dc);
-
 	/* we want to turn off all dp displays before doing detection */
-	if (dc->config.power_down_display_on_boot) {
-		uint8_t dpcd_power_state = '\0';
-		enum dc_status status = DC_ERROR_UNEXPECTED;
+	if (dc->config.power_down_display_on_boot)
+		dc_link_blank_all_dp_displays(dc);
 
-		for (i = 0; i < dc->link_count; i++) {
-			if (dc->links[i]->connector_signal != SIGNAL_TYPE_DISPLAY_PORT)
-				continue;
-
-			/* DP 2.0 requires that LTTPR Caps be read first */
-			dp_retrieve_lttpr_cap(dc->links[i]);
-
-			/*
-			 * If any of the displays are lit up turn them off.
-			 * The reason is that some MST hubs cannot be turned off
-			 * completely until we tell them to do so.
-			 * If not turned off, then displays connected to MST hub
-			 * won't light up.
-			 */
-			status = core_link_read_dpcd(dc->links[i], DP_SET_POWER,
-							&dpcd_power_state, sizeof(dpcd_power_state));
-			if (status == DC_OK && dpcd_power_state == DP_POWER_STATE_D0) {
-				/* blank dp stream before power off receiver*/
-				if (dc->links[i]->link_enc->funcs->get_dig_frontend) {
-					unsigned int fe = dc->links[i]->link_enc->funcs->get_dig_frontend(dc->links[i]->link_enc);
-
-					for (j = 0; j < dc->res_pool->stream_enc_count; j++) {
-						if (fe == dc->res_pool->stream_enc[j]->id) {
-							dc->res_pool->stream_enc[j]->funcs->dp_blank(
-										dc->res_pool->stream_enc[j]);
-							break;
-						}
-					}
-				}
-				dp_receiver_power_ctrl(dc->links[i], false);
-			}
-		}
-	}
+	if (hws->funcs.enable_power_gating_plane)
+		hws->funcs.enable_power_gating_plane(dc->hwseq, true);
 
 	/* If taking control over from VBIOS, we may want to optimize our first
 	 * mode set, so we need to skip powering down pipes until we know which
@@ -1487,8 +1481,6 @@
 
 		REG_UPDATE(DCFCLK_CNTL, DCFCLK_GATE_DIS, 0);
 	}
-	if (hws->funcs.enable_power_gating_plane)
-		hws->funcs.enable_power_gating_plane(dc->hwseq, true);
 
 	if (dc->clk_mgr->funcs->notify_wm_ranges)
 		dc->clk_mgr->funcs->notify_wm_ranges(dc->clk_mgr);
@@ -1522,7 +1514,7 @@
 		for (i = 0; i < dc->link_count; i++) {
 			struct dc_link *link = dc->links[i];
 
-			if (link->link_enc->funcs->is_dig_enabled &&
+			if (link->link_enc && link->link_enc->funcs->is_dig_enabled &&
 					link->link_enc->funcs->is_dig_enabled(link->link_enc) &&
 					dc->hwss.power_down) {
 				dc->hwss.power_down(dc);
@@ -1714,6 +1706,9 @@
 {
 	struct dpp *dpp = pipe_ctx->plane_res.dpp;
 
+	if (!stream)
+		return false;
+
 	if (dpp == NULL)
 		return false;
 
@@ -1736,8 +1731,8 @@
 	} else
 		dpp->funcs->dpp_program_regamma_pwl(dpp, NULL, OPP_REGAMMA_BYPASS);
 
-	if (stream != NULL && stream->ctx != NULL &&
-			stream->out_transfer_func != NULL) {
+	if (stream->ctx &&
+	    stream->out_transfer_func) {
 		log_tf(stream->ctx,
 				stream->out_transfer_func,
 				dpp->regamma_params.hw_points_num);
@@ -2455,14 +2450,18 @@
 	struct mpc *mpc = dc->res_pool->mpc;
 	struct mpc_tree *mpc_tree_params = &(pipe_ctx->stream_res.opp->mpc_tree_params);
 
-	if (per_pixel_alpha)
-		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_PER_PIXEL_ALPHA;
-	else
-		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_GLOBAL_ALPHA;
-
 	blnd_cfg.overlap_only = false;
 	blnd_cfg.global_gain = 0xff;
 
+	if (per_pixel_alpha && pipe_ctx->plane_state->global_alpha) {
+		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_PER_PIXEL_ALPHA_COMBINED_GLOBAL_GAIN;
+		blnd_cfg.global_gain = pipe_ctx->plane_state->global_alpha_value;
+	} else if (per_pixel_alpha) {
+		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_PER_PIXEL_ALPHA;
+	} else {
+		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_GLOBAL_ALPHA;
+	}
+
 	if (pipe_ctx->plane_state->global_alpha)
 		blnd_cfg.global_alpha = pipe_ctx->plane_state->global_alpha_value;
 	else
@@ -2767,7 +2766,7 @@
 
 		pipe_ctx->stream_res.tg->funcs->program_global_sync(
 				pipe_ctx->stream_res.tg,
-				pipe_ctx->pipe_dlg_param.vready_offset,
+				calculate_vready_offset_for_group(pipe_ctx),
 				pipe_ctx->pipe_dlg_param.vstartup_start,
 				pipe_ctx->pipe_dlg_param.vupdate_offset,
 				pipe_ctx->pipe_dlg_param.vupdate_width);
@@ -3107,7 +3106,9 @@
 		if (pipe_ctx->stream_res.opp->mpcc_disconnect_pending[mpcc_inst]) {
 			struct hubp *hubp = get_hubp_by_inst(res_pool, mpcc_inst);
 
-			res_pool->mpc->funcs->wait_for_idle(res_pool->mpc, mpcc_inst);
+			if (pipe_ctx->stream_res.tg &&
+				pipe_ctx->stream_res.tg->funcs->is_tg_enabled(pipe_ctx->stream_res.tg))
+				res_pool->mpc->funcs->wait_for_idle(res_pool->mpc, mpcc_inst);
 			pipe_ctx->stream_res.opp->mpcc_disconnect_pending[mpcc_inst] = false;
 			hubp->funcs->set_blank(hubp, true);
 		}
@@ -3176,13 +3177,11 @@
 
 static bool dcn10_can_pipe_disable_cursor(struct pipe_ctx *pipe_ctx)
 {
-	struct pipe_ctx *test_pipe;
+	struct pipe_ctx *test_pipe, *split_pipe;
 	const struct scaler_data *scl_data = &pipe_ctx->plane_res.scl_data;
-	const struct rect *r1 = &scl_data->recout, *r2;
-	int r1_r = r1->x + r1->width, r1_b = r1->y + r1->height, r2_r, r2_b;
+	struct rect r1 = scl_data->recout, r2, r2_half;
+	int r1_r = r1.x + r1.width, r1_b = r1.y + r1.height, r2_r, r2_b;
 	int cur_layer = pipe_ctx->plane_state->layer_index;
-	bool upper_pipe_exists = false;
-	struct fixed31_32 one = dc_fixpt_from_int(1);
 
 	/**
 	 * Disable the cursor if there's another pipe above this with a
@@ -3191,26 +3190,35 @@
 	 */
 	for (test_pipe = pipe_ctx->top_pipe; test_pipe;
 	     test_pipe = test_pipe->top_pipe) {
-		if (!test_pipe->plane_state->visible)
+		// Skip invisible layer and pipe-split plane on same layer
+		if (!test_pipe->plane_state ||
+		    !test_pipe->plane_state->visible ||
+		    test_pipe->plane_state->layer_index == cur_layer)
 			continue;
 
-		r2 = &test_pipe->plane_res.scl_data.recout;
-		r2_r = r2->x + r2->width;
-		r2_b = r2->y + r2->height;
+		r2 = test_pipe->plane_res.scl_data.recout;
+		r2_r = r2.x + r2.width;
+		r2_b = r2.y + r2.height;
+		split_pipe = test_pipe;
 
-		if (r1->x >= r2->x && r1->y >= r2->y && r1_r <= r2_r && r1_b <= r2_b)
-			return true;
+		/**
+		 * There is another half plane on same layer because of
+		 * pipe-split, merge together per same height.
+		 */
+		for (split_pipe = pipe_ctx->top_pipe; split_pipe;
+		     split_pipe = split_pipe->top_pipe)
+			if (split_pipe->plane_state->layer_index == test_pipe->plane_state->layer_index) {
+				r2_half = split_pipe->plane_res.scl_data.recout;
+				r2.x = (r2_half.x < r2.x) ? r2_half.x : r2.x;
+				r2.width = r2.width + r2_half.width;
+				r2_r = r2.x + r2.width;
+				break;
+			}
 
-		if (test_pipe->plane_state->layer_index < cur_layer)
-			upper_pipe_exists = true;
+		if (r1.x >= r2.x && r1.y >= r2.y && r1_r <= r2_r && r1_b <= r2_b)
+			return true;
 	}
 
-	// if plane scaled, assume an upper plane can handle cursor if it exists.
-	if (upper_pipe_exists &&
-			(scl_data->ratios.horz.value != one.value ||
-			scl_data->ratios.vert.value != one.value))
-		return true;
-
 	return false;
 }
 
@@ -3508,7 +3516,7 @@
 {
 	const struct dc_crtc_timing *dc_crtc_timing = &pipe_ctx->stream->timing;
 	int vline_int_offset_from_vupdate =
-			pipe_ctx->stream->periodic_interrupt0.lines_offset;
+			pipe_ctx->stream->periodic_interrupt.lines_offset;
 	int vupdate_offset_from_vsync = dc->hwss.get_vupdate_offset_from_vsync(pipe_ctx);
 	int start_position;
 
@@ -3533,18 +3541,10 @@
 static void dcn10_cal_vline_position(
 		struct dc *dc,
 		struct pipe_ctx *pipe_ctx,
-		enum vline_select vline,
 		uint32_t *start_line,
 		uint32_t *end_line)
 {
-	enum vertical_interrupt_ref_point ref_point = INVALID_POINT;
-
-	if (vline == VLINE0)
-		ref_point = pipe_ctx->stream->periodic_interrupt0.ref_point;
-	else if (vline == VLINE1)
-		ref_point = pipe_ctx->stream->periodic_interrupt1.ref_point;
-
-	switch (ref_point) {
+	switch (pipe_ctx->stream->periodic_interrupt.ref_point) {
 	case START_V_UPDATE:
 		dcn10_calc_vupdate_position(
 				dc,
@@ -3553,7 +3553,9 @@
 				end_line);
 		break;
 	case START_V_SYNC:
-		// Suppose to do nothing because vsync is 0;
+		// vsync is line 0 so start_line is just the requested line offset
+		*start_line = pipe_ctx->stream->periodic_interrupt.lines_offset;
+		*end_line = *start_line + 2;
 		break;
 	default:
 		ASSERT(0);
@@ -3563,24 +3565,15 @@
 
 void dcn10_setup_periodic_interrupt(
 		struct dc *dc,
-		struct pipe_ctx *pipe_ctx,
-		enum vline_select vline)
+		struct pipe_ctx *pipe_ctx)
 {
 	struct timing_generator *tg = pipe_ctx->stream_res.tg;
+	uint32_t start_line = 0;
+	uint32_t end_line = 0;
 
-	if (vline == VLINE0) {
-		uint32_t start_line = 0;
-		uint32_t end_line = 0;
-
-		dcn10_cal_vline_position(dc, pipe_ctx, vline, &start_line, &end_line);
-
-		tg->funcs->setup_vertical_interrupt0(tg, start_line, end_line);
-
-	} else if (vline == VLINE1) {
-		pipe_ctx->stream_res.tg->funcs->setup_vertical_interrupt1(
-				tg,
-				pipe_ctx->stream->periodic_interrupt1.lines_offset);
-	}
+	dcn10_cal_vline_position(dc, pipe_ctx, &start_line, &end_line);
+
+	tg->funcs->setup_vertical_interrupt0(tg, start_line, end_line);
 }
 
 void dcn10_setup_vupdate_interrupt(struct dc *dc, struct pipe_ctx *pipe_ctx)
@@ -3613,7 +3606,7 @@
 	if (dc_is_dp_signal(pipe_ctx->stream->signal)) {
 		if (params.timing.pixel_encoding == PIXEL_ENCODING_YCBCR420)
 			params.timing.pix_clk_100hz /= 2;
-		pipe_ctx->stream_res.stream_enc->funcs->dp_unblank(pipe_ctx->stream_res.stream_enc, &params);
+		pipe_ctx->stream_res.stream_enc->funcs->dp_unblank(link, pipe_ctx->stream_res.stream_enc, &params);
 	}
 
 	if (link->local_sink && link->local_sink->sink_signal == SIGNAL_TYPE_EDP) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.h
@@ -175,8 +175,7 @@
 void dcn10_set_cursor_sdr_white_level(struct pipe_ctx *pipe_ctx);
 void dcn10_setup_periodic_interrupt(
 		struct dc *dc,
-		struct pipe_ctx *pipe_ctx,
-		enum vline_select vline);
+		struct pipe_ctx *pipe_ctx);
 enum dc_status dcn10_set_clock(struct dc *dc,
 		enum dc_clock_type clock_type,
 		uint32_t clk_khz,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_init.c
@@ -78,6 +78,7 @@
 	.get_clock = dcn10_get_clock,
 	.get_vupdate_offset_from_vsync = dcn10_get_vupdate_offset_from_vsync,
 	.calc_vupdate_position = dcn10_calc_vupdate_position,
+	.power_down = dce110_power_down,
 	.set_backlight_level = dce110_set_backlight_level,
 	.set_abm_immediate_disable = dce110_set_abm_immediate_disable,
 	.set_pipe = dce110_set_pipe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_mpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_mpc.c
@@ -126,6 +126,12 @@
 	while (tmp_mpcc != NULL) {
 		if (tmp_mpcc->dpp_id == dpp_id)
 			return tmp_mpcc;
+
+		/* avoid circular linked list */
+		ASSERT(tmp_mpcc != tmp_mpcc->mpcc_bot);
+		if (tmp_mpcc == tmp_mpcc->mpcc_bot)
+			break;
+
 		tmp_mpcc = tmp_mpcc->mpcc_bot;
 	}
 	return NULL;
@@ -201,8 +207,9 @@
 		/* check insert_above_mpcc exist in tree->opp_list */
 		struct mpcc *temp_mpcc = tree->opp_list;
 
-		while (temp_mpcc && temp_mpcc->mpcc_bot != insert_above_mpcc)
-			temp_mpcc = temp_mpcc->mpcc_bot;
+		if (temp_mpcc != insert_above_mpcc)
+			while (temp_mpcc && temp_mpcc->mpcc_bot != insert_above_mpcc)
+				temp_mpcc = temp_mpcc->mpcc_bot;
 		if (temp_mpcc == NULL)
 			return NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_optc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_optc.c
@@ -480,6 +480,11 @@
 				OTG_CLOCK_ON, 1,
 				1, 1000);
 	} else  {
+
+		//last chance to clear underflow, otherwise, it will always there due to clock is off.
+		if (optc->funcs->is_optc_underflow_occurred(optc) == true)
+			optc->funcs->clear_optc_underflow(optc);
+
 		REG_UPDATE_2(OTG_CLOCK_CONTROL,
 				OTG_CLOCK_GATE_DIS, 0,
 				OTG_CLOCK_EN, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_resource.c
@@ -1296,7 +1296,7 @@
 			 * in daisy chain use case
 			 */
 			j = i;
-			if (pool->stream_enc[i]->id ==
+			if (link->ep_type == DISPLAY_ENDPOINT_PHY && pool->stream_enc[i]->id ==
 					link->link_enc->preferred_engine)
 				return pool->stream_enc[i];
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_stream_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_stream_encoder.c
@@ -29,6 +29,8 @@
 #include "dcn10_stream_encoder.h"
 #include "reg_helper.h"
 #include "hw_shared.h"
+#include "inc/link_dpcd.h"
+#include "dpcd_defs.h"
 
 #define DC_LOGGER \
 		enc1->base.ctx->logger
@@ -644,6 +646,12 @@
 				x),
 			26));
 
+	// If y rounds up to integer, carry it over to x.
+	if (y >> 26) {
+		x += 1;
+		y = 0;
+	}
+
 	REG_SET_2(DP_MSE_RATE_CNTL, 0,
 		DP_MSE_RATE_X, x,
 		DP_MSE_RATE_Y, y);
@@ -884,6 +892,7 @@
 }
 
 void enc1_stream_encoder_dp_blank(
+	struct dc_link *link,
 	struct stream_encoder *enc)
 {
 	struct dcn10_stream_encoder *enc1 = DCN10STRENC_FROM_STRENC(enc);
@@ -914,6 +923,8 @@
 	/* disable DP stream */
 	REG_UPDATE(DP_VID_STREAM_CNTL, DP_VID_STREAM_ENABLE, 0);
 
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_DISABLE_DP_VID_STREAM);
+
 	/* the encoder stops sending the video stream
 	 * at the start of the vertical blanking.
 	 * Poll for DP_VID_STREAM_STATUS == 0
@@ -930,10 +941,13 @@
 	 */
 
 	REG_UPDATE(DP_STEER_FIFO, DP_STEER_FIFO_RESET, true);
+
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_FIFO_STEER_RESET);
 }
 
 /* output video stream to link encoder */
 void enc1_stream_encoder_dp_unblank(
+	struct dc_link *link,
 	struct stream_encoder *enc,
 	const struct encoder_unblank_param *param)
 {
@@ -1000,6 +1014,8 @@
 	 */
 
 	REG_UPDATE(DP_VID_STREAM_CNTL, DP_VID_STREAM_ENABLE, true);
+
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_ENABLE_DP_VID_STREAM);
 }
 
 void enc1_stream_encoder_set_avmute(
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_stream_encoder.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_stream_encoder.h
@@ -627,9 +627,11 @@
 	struct stream_encoder *enc);
 
 void enc1_stream_encoder_dp_blank(
+	struct dc_link *link,
 	struct stream_encoder *enc);
 
 void enc1_stream_encoder_dp_unblank(
+	struct dc_link *link,
 	struct stream_encoder *enc,
 	const struct encoder_unblank_param *param);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c
@@ -690,6 +690,9 @@
 	int pair;
 	uint16_t odd_coef, even_coef;
 
+	if (!filter)
+		return;
+
 	for (phase = 0; phase < (NUM_PHASES / 2 + 1); phase++) {
 		for (pair = 0; pair < tap_pairs; pair++) {
 			even_coef = filter[phase * taps + 2 * pair];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c
@@ -52,6 +52,9 @@
 #include "dc_dmub_srv.h"
 #include "dce/dmub_hw_lock_mgr.h"
 #include "hw_sequencer.h"
+#include "inc/link_dpcd.h"
+#include "dpcd_defs.h"
+#include "inc/link_enc_cfg.h"
 
 #define DC_LOGGER_INIT(logger)
 
@@ -1513,6 +1516,7 @@
 	/* Any updates are handled in dc interface, just need
 	 * to apply existing for plane enable / opp change */
 	if (pipe_ctx->update_flags.bits.enable || pipe_ctx->update_flags.bits.opp_changed
+			|| pipe_ctx->update_flags.bits.plane_changed
 			|| pipe_ctx->stream->update_flags.bits.gamut_remap
 			|| pipe_ctx->stream->update_flags.bits.out_csc) {
 		/* dpp/cm gamut remap*/
@@ -1563,6 +1567,31 @@
 		hubp->funcs->set_blank(hubp, false);
 }
 
+static int calculate_vready_offset_for_group(struct pipe_ctx *pipe)
+{
+	struct pipe_ctx *other_pipe;
+	int vready_offset = pipe->pipe_dlg_param.vready_offset;
+
+	/* Always use the largest vready_offset of all connected pipes */
+	for (other_pipe = pipe->bottom_pipe; other_pipe != NULL; other_pipe = other_pipe->bottom_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+	for (other_pipe = pipe->top_pipe; other_pipe != NULL; other_pipe = other_pipe->top_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+	for (other_pipe = pipe->next_odm_pipe; other_pipe != NULL; other_pipe = other_pipe->next_odm_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+	for (other_pipe = pipe->prev_odm_pipe; other_pipe != NULL; other_pipe = other_pipe->prev_odm_pipe) {
+		if (other_pipe->pipe_dlg_param.vready_offset > vready_offset)
+			vready_offset = other_pipe->pipe_dlg_param.vready_offset;
+	}
+
+	return vready_offset;
+}
 
 static void dcn20_program_pipe(
 		struct dc *dc,
@@ -1581,7 +1610,7 @@
 
 		pipe_ctx->stream_res.tg->funcs->program_global_sync(
 				pipe_ctx->stream_res.tg,
-				pipe_ctx->pipe_dlg_param.vready_offset,
+				calculate_vready_offset_for_group(pipe_ctx),
 				pipe_ctx->pipe_dlg_param.vstartup_start,
 				pipe_ctx->pipe_dlg_param.vupdate_offset,
 				pipe_ctx->pipe_dlg_param.vupdate_width);
@@ -1764,7 +1793,7 @@
 
 			for (j = 0; j < TIMEOUT_FOR_PIPE_ENABLE_MS*1000
 					&& hubp->funcs->hubp_is_flip_pending(hubp); j++)
-				mdelay(1);
+				udelay(1);
 		}
 	}
 
@@ -1874,7 +1903,7 @@
 
 			pipe_ctx->stream_res.tg->funcs->program_global_sync(
 					pipe_ctx->stream_res.tg,
-					pipe_ctx->pipe_dlg_param.vready_offset,
+					calculate_vready_offset_for_group(pipe_ctx),
 					pipe_ctx->pipe_dlg_param.vstartup_start,
 					pipe_ctx->pipe_dlg_param.vupdate_offset,
 					pipe_ctx->pipe_dlg_param.vupdate_width);
@@ -2140,7 +2169,7 @@
 			params.timing.pix_clk_100hz /= 2;
 		pipe_ctx->stream_res.stream_enc->funcs->dp_set_odm_combine(
 				pipe_ctx->stream_res.stream_enc, params.opp_cnt > 1);
-		pipe_ctx->stream_res.stream_enc->funcs->dp_unblank(pipe_ctx->stream_res.stream_enc, &params);
+		pipe_ctx->stream_res.stream_enc->funcs->dp_unblank(link, pipe_ctx->stream_res.stream_enc, &params);
 	}
 
 	if (link->local_sink && link->local_sink->sink_signal == SIGNAL_TYPE_EDP) {
@@ -2297,14 +2326,18 @@
 	struct mpc *mpc = dc->res_pool->mpc;
 	struct mpc_tree *mpc_tree_params = &(pipe_ctx->stream_res.opp->mpc_tree_params);
 
-	if (per_pixel_alpha)
-		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_PER_PIXEL_ALPHA;
-	else
-		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_GLOBAL_ALPHA;
-
 	blnd_cfg.overlap_only = false;
 	blnd_cfg.global_gain = 0xff;
 
+	if (per_pixel_alpha && pipe_ctx->plane_state->global_alpha) {
+		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_PER_PIXEL_ALPHA_COMBINED_GLOBAL_GAIN;
+		blnd_cfg.global_gain = pipe_ctx->plane_state->global_alpha_value;
+	} else if (per_pixel_alpha) {
+		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_PER_PIXEL_ALPHA;
+	} else {
+		blnd_cfg.alpha_mode = MPCC_ALPHA_BLEND_MODE_GLOBAL_ALPHA;
+	}
+
 	if (pipe_ctx->plane_state->global_alpha)
 		blnd_cfg.global_alpha = pipe_ctx->plane_state->global_alpha_value;
 	else
@@ -2374,14 +2407,26 @@
 	uint32_t active_total_with_borders;
 	uint32_t early_control = 0;
 	struct timing_generator *tg = pipe_ctx->stream_res.tg;
+	struct link_encoder *link_enc;
+
+	if (link->is_dig_mapping_flexible &&
+			link->dc->res_pool->funcs->link_encs_assign)
+		link_enc = link_enc_cfg_get_link_enc_used_by_stream(link->ctx->dc, pipe_ctx->stream);
+	else
+		link_enc = link->link_enc;
+	ASSERT(link_enc);
 
 	/* For MST, there are multiply stream go to only one link.
 	 * connect DIG back_end to front_end while enable_stream and
 	 * disconnect them during disable_stream
 	 * BY this, it is logic clean to separate stream and link
 	 */
-	link->link_enc->funcs->connect_dig_be_to_fe(link->link_enc,
-						    pipe_ctx->stream_res.stream_enc->id, true);
+	if (link_enc)
+		link_enc->funcs->connect_dig_be_to_fe(
+			link_enc, pipe_ctx->stream_res.stream_enc->id, true);
+
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_CONNECT_DIG_FE_BE);
 
 	if (pipe_ctx->plane_state && pipe_ctx->plane_state->flip_immediate != 1) {
 		if (link->dc->hwss.program_dmdata_engine)
@@ -2390,6 +2435,9 @@
 
 	link->dc->hwss.update_info_frame(pipe_ctx);
 
+	if (dc_is_dp_signal(pipe_ctx->stream->signal))
+		dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_UPDATE_INFO_FRAME);
+
 	/* enable early control to avoid corruption on DP monitor*/
 	active_total_with_borders =
 			timing->h_addressable
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_mpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_mpc.c
@@ -532,6 +532,12 @@
 	while (tmp_mpcc != NULL) {
 		if (tmp_mpcc->dpp_id == 0xf || tmp_mpcc->dpp_id == dpp_id)
 			return tmp_mpcc;
+
+		/* avoid circular linked list */
+		ASSERT(tmp_mpcc != tmp_mpcc->mpcc_bot);
+		if (tmp_mpcc == tmp_mpcc->mpcc_bot)
+			break;
+
 		tmp_mpcc = tmp_mpcc->mpcc_bot;
 	}
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c
@@ -35,7 +35,7 @@
 #include "include/irq_service_interface.h"
 #include "dcn20/dcn20_resource.h"
 
-#include "dml/dcn2x/dcn2x.h"
+#include "dml/dcn20/dcn20_fpu.h"
 
 #include "dcn10/dcn10_hubp.h"
 #include "dcn10/dcn10_ipp.h"
@@ -86,6 +86,7 @@
 #include "dce/dce_aux.h"
 #include "dce/dce_i2c.h"
 #include "vm_helper.h"
+#include "link_enc_cfg.h"
 
 #include "amdgpu_socbb.h"
 
@@ -1595,12 +1596,28 @@
 	const struct dc_stream_state *stream = pipe_ctx->stream;
 	struct pipe_ctx *odm_pipe;
 	int opp_cnt = 1;
+	struct dc_link *link = stream->link;
+	struct link_encoder *link_enc = NULL;
 
 	for (odm_pipe = pipe_ctx->next_odm_pipe; odm_pipe; odm_pipe = odm_pipe->next_odm_pipe)
 		opp_cnt++;
 
 	pixel_clk_params->requested_pix_clk_100hz = stream->timing.pix_clk_100hz;
-	pixel_clk_params->encoder_object_id = stream->link->link_enc->id;
+
+	/* Links supporting dynamically assigned link encoder will be assigned next
+	 * available encoder if one not already assigned.
+	 */
+	if (link->is_dig_mapping_flexible &&
+			link->dc->res_pool->funcs->link_encs_assign) {
+		link_enc = link_enc_cfg_get_link_enc_used_by_stream(stream->ctx->dc, stream);
+		if (link_enc == NULL)
+			link_enc = link_enc_cfg_get_next_avail_link_enc(stream->ctx->dc);
+	} else
+		link_enc = stream->link->link_enc;
+	ASSERT(link_enc);
+
+	if (link_enc)
+		pixel_clk_params->encoder_object_id = link_enc->id;
 	pixel_clk_params->signal_type = pipe_ctx->stream->signal;
 	pixel_clk_params->controller_id = pipe_ctx->stream_res.tg->inst + 1;
 	/* TODO: un-hardcode*/
@@ -1854,7 +1871,9 @@
 	case DC_SW_VAR_D_X:
 		*sw_mode = dm_sw_var_d_x;
 		break;
-
+	case DC_SW_VAR_R_X:
+		*sw_mode = dm_sw_var_r_x;
+		break;
 	default:
 		ASSERT(0); /* Not supported */
 		break;
@@ -3152,7 +3171,7 @@
 
 		context->bw_ctx.dml.funcs.rq_dlg_get_rq_reg(&context->bw_ctx.dml,
 				&context->res_ctx.pipe_ctx[i].rq_regs,
-				pipes[pipe_idx].pipe);
+				&pipes[pipe_idx].pipe);
 		pipe_idx++;
 	}
 }
@@ -3668,16 +3687,22 @@
 			clock_limits_available = (status == PP_SMU_RESULT_OK);
 		}
 
-		if (clock_limits_available && uclk_states_available && num_states)
+		if (clock_limits_available && uclk_states_available && num_states) {
+			DC_FP_START();
 			dcn20_update_bounding_box(dc, loaded_bb, &max_clocks, uclk_states, num_states);
-		else if (clock_limits_available)
+			DC_FP_END();
+		} else if (clock_limits_available) {
+			DC_FP_START();
 			dcn20_cap_soc_clocks(loaded_bb, max_clocks);
+			DC_FP_END();
+		}
 	}
 
 	loaded_ip->max_num_otg = pool->base.res_cap->num_timing_generator;
 	loaded_ip->max_num_dpp = pool->base.pipe_count;
+	DC_FP_START();
 	dcn20_patch_bounding_box(dc, loaded_bb);
-
+	DC_FP_END();
 	return true;
 }
 
@@ -3697,8 +3722,6 @@
 	enum dml_project dml_project_version =
 			get_dml_project_version(ctx->asic_id.hw_internal_rev);
 
-	DC_FP_START();
-
 	ctx->dc_bios->regs = &bios_regs;
 	pool->base.funcs = &dcn20_res_pool_funcs;
 
@@ -4047,12 +4070,10 @@
 		pool->base.oem_device = NULL;
 	}
 
-	DC_FP_END();
 	return true;
 
 create_fail:
 
-	DC_FP_END();
 	dcn20_resource_destruct(pool);
 
 	return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_stream_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_stream_encoder.c
@@ -29,6 +29,8 @@
 #include "dcn20_stream_encoder.h"
 #include "reg_helper.h"
 #include "hw_shared.h"
+#include "inc/link_dpcd.h"
+#include "dpcd_defs.h"
 
 #define DC_LOGGER \
 		enc1->base.ctx->logger
@@ -444,6 +446,7 @@
 }
 
 void enc2_stream_encoder_dp_unblank(
+		struct dc_link *link,
 		struct stream_encoder *enc,
 		const struct encoder_unblank_param *param)
 {
@@ -522,6 +525,8 @@
 	 */
 
 	REG_UPDATE(DP_VID_STREAM_CNTL, DP_VID_STREAM_ENABLE, true);
+
+	dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_ENABLE_DP_VID_STREAM);
 }
 
 static void enc2_dp_set_odm_combine(
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_stream_encoder.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn20/dcn20_stream_encoder.h
@@ -104,6 +104,7 @@
 	uint32_t enable_sdp_splitting);
 
 void enc2_stream_encoder_dp_unblank(
+	struct dc_link *link,
 	struct stream_encoder *enc,
 	const struct encoder_unblank_param *param);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hubbub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hubbub.c
@@ -67,9 +67,15 @@
 void dcn21_dchvm_init(struct hubbub *hubbub)
 {
 	struct dcn20_hubbub *hubbub1 = TO_DCN20_HUBBUB(hubbub);
-	uint32_t riommu_active;
+	uint32_t riommu_active, prefetch_done;
 	int i;
 
+	REG_GET(DCHVM_RIOMMU_STAT0, HOSTVM_PREFETCH_DONE, &prefetch_done);
+
+	if (prefetch_done) {
+		hubbub->riommu_active = true;
+		return;
+	}
 	//Init DCHVM block
 	REG_UPDATE(DCHVM_CTRL0, HOSTVM_INIT_REQ, 1);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hwseq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn21/dcn21_hwseq.c
@@ -182,9 +182,15 @@
 void dcn21_set_pipe(struct pipe_ctx *pipe_ctx)
 {
 	struct abm *abm = pipe_ctx->stream_res.abm;
-	uint32_t otg_inst = pipe_ctx->stream_res.tg->inst;
+	struct timing_generator *tg = pipe_ctx->stream_res.tg;
 	struct panel_cntl *panel_cntl = pipe_ctx->stream->link->panel_cntl;
 	struct dmcu *dmcu = pipe_ctx->stream->ctx->dc->res_pool->dmcu;
+	uint32_t otg_inst;
+
+	if (!abm && !tg && !panel_cntl)
+		return;
+
+	otg_inst = tg->inst;
 
 	if (dmcu) {
 		dce110_set_pipe(pipe_ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn21/dcn21_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn21/dcn21_resource.c
@@ -35,7 +35,7 @@
 #include "include/irq_service_interface.h"
 #include "dcn20/dcn20_resource.h"
 
-#include "dml/dcn2x/dcn2x.h"
+#include "dml/dcn20/dcn20_fpu.h"
 
 #include "clk_mgr.h"
 #include "dcn10/dcn10_hubp.h"
@@ -1428,6 +1428,7 @@
 		return &clk_src->base;
 	}
 
+	kfree(clk_src);
 	BREAK_TO_DEBUGGER();
 	return NULL;
 }
@@ -1851,7 +1852,7 @@
 		kzalloc(sizeof(struct dcn21_link_encoder), GFP_KERNEL);
 	int link_regs_id;
 
-	if (!enc21)
+	if (!enc21 || enc_init_data->hpd_source >= ARRAY_SIZE(link_enc_hpd_regs))
 		return NULL;
 
 	link_regs_id =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_cm_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_cm_common.c
@@ -178,6 +178,8 @@
 				i += increment) {
 			if (j == hw_points - 1)
 				break;
+			if (i >= TRANSFER_FUNC_POINTS)
+				return false;
 			rgb_resulted[j].red = output_tf->tf_pts.red[i];
 			rgb_resulted[j].green = output_tf->tf_pts.green[i];
 			rgb_resulted[j].blue = output_tf->tf_pts.blue[i];
@@ -355,6 +357,8 @@
 				i += increment) {
 			if (j == hw_points - 1)
 				break;
+			if (i >= TRANSFER_FUNC_POINTS)
+				return false;
 			rgb_resulted[j].red = output_tf->tf_pts.red[i];
 			rgb_resulted[j].green = output_tf->tf_pts.green[i];
 			rgb_resulted[j].blue = output_tf->tf_pts.blue[i];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp.c
@@ -355,8 +355,11 @@
 	int cur_rom_en = 0;
 
 	if (color_format == CURSOR_MODE_COLOR_PRE_MULTIPLIED_ALPHA ||
-		color_format == CURSOR_MODE_COLOR_UN_PRE_MULTIPLIED_ALPHA)
-		cur_rom_en = 1;
+		color_format == CURSOR_MODE_COLOR_UN_PRE_MULTIPLIED_ALPHA) {
+		if (cursor_attributes->attribute_flags.bits.ENABLE_CURSOR_DEGAMMA) {
+			cur_rom_en = 1;
+		}
+	}
 
 	REG_UPDATE_3(CURSOR0_CONTROL,
 			CUR0_MODE, color_format,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_hubbub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_hubbub.c
@@ -448,6 +448,7 @@
 	.program_watermarks = hubbub3_program_watermarks,
 	.allow_self_refresh_control = hubbub1_allow_self_refresh_control,
 	.is_allow_self_refresh_enabled = hubbub1_is_allow_self_refresh_enabled,
+	.verify_allow_pstate_change_high = hubbub1_verify_allow_pstate_change_high,
 	.force_wm_propagate_to_pipes = hubbub3_force_wm_propagate_to_pipes,
 	.force_pstate_change_control = hubbub3_force_pstate_change_control,
 	.init_watermarks = hubbub3_init_watermarks,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_hubp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_hubp.c
@@ -86,7 +86,7 @@
 			VMID, address->vmid);
 
 	if (address->type == PLN_ADDR_TYPE_GRPH_STEREO) {
-		REG_UPDATE(DCSURF_FLIP_CONTROL, SURFACE_FLIP_MODE_FOR_STEREOSYNC, 0x1);
+		REG_UPDATE(DCSURF_FLIP_CONTROL, SURFACE_FLIP_MODE_FOR_STEREOSYNC, 0);
 		REG_UPDATE(DCSURF_FLIP_CONTROL, SURFACE_FLIP_IN_STEREOSYNC, 0x1);
 
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_hwseq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_hwseq.c
@@ -212,7 +212,11 @@
 		}
 	}
 
-	mpc->funcs->set_output_gamma(mpc, mpcc_id, params);
+	if (mpc->funcs->set_output_gamma)
+		mpc->funcs->set_output_gamma(mpc, mpcc_id, params);
+	else
+		DC_LOG_ERROR("%s: set_output_gamma function pointer is NULL.\n", __func__);
+
 	return ret;
 }
 
@@ -437,7 +441,7 @@
 	struct dce_hwseq *hws = dc->hwseq;
 	struct dc_bios *dcb = dc->ctx->dc_bios;
 	struct resource_pool *res_pool = dc->res_pool;
-	int i, j;
+	int i;
 	int edp_num;
 	uint32_t backlight = MAX_BACKLIGHT_LEVEL;
 
@@ -534,41 +538,11 @@
 			hws->funcs.dsc_pg_control(hws, res_pool->dscs[i]->inst, false);
 
 	/* we want to turn off all dp displays before doing detection */
-	if (dc->config.power_down_display_on_boot) {
-		uint8_t dpcd_power_state = '\0';
-		enum dc_status status = DC_ERROR_UNEXPECTED;
-
-		for (i = 0; i < dc->link_count; i++) {
-			if (dc->links[i]->connector_signal != SIGNAL_TYPE_DISPLAY_PORT)
-				continue;
-			/* DP 2.0 states that LTTPR regs must be read first */
-			dp_retrieve_lttpr_cap(dc->links[i]);
+	if (dc->config.power_down_display_on_boot)
+		dc_link_blank_all_dp_displays(dc);
 
-			/* if any of the displays are lit up turn them off */
-			status = core_link_read_dpcd(dc->links[i], DP_SET_POWER,
-						     &dpcd_power_state, sizeof(dpcd_power_state));
-			if (status == DC_OK && dpcd_power_state == DP_POWER_STATE_D0) {
-				/* blank dp stream before power off receiver*/
-				if (dc->links[i]->link_enc->funcs->get_dig_frontend) {
-					unsigned int fe;
-
-					fe = dc->links[i]->link_enc->funcs->get_dig_frontend(
-										dc->links[i]->link_enc);
-					if (fe == ENGINE_ID_UNKNOWN)
-						continue;
-
-					for (j = 0; j < dc->res_pool->stream_enc_count; j++) {
-						if (fe == dc->res_pool->stream_enc[j]->id) {
-							dc->res_pool->stream_enc[j]->funcs->dp_blank(
-										dc->res_pool->stream_enc[j]);
-							break;
-						}
-					}
-				}
-				dp_receiver_power_ctrl(dc->links[i], false);
-			}
-		}
-	}
+	if (hws->funcs.enable_power_gating_plane)
+		hws->funcs.enable_power_gating_plane(dc->hwseq, true);
 
 	/* If taking control over from VBIOS, we may want to optimize our first
 	 * mode set, so we need to skip powering down pipes until we know which
@@ -647,8 +621,6 @@
 
 		REG_UPDATE(DCFCLK_CNTL, DCFCLK_GATE_DIS, 0);
 	}
-	if (hws->funcs.enable_power_gating_plane)
-		hws->funcs.enable_power_gating_plane(dc->hwseq, true);
 
 	if (!dcb->funcs->is_accelerated_mode(dcb) && dc->res_pool->hubbub->funcs->init_watermarks)
 		dc->res_pool->hubbub->funcs->init_watermarks(dc->res_pool->hubbub);
@@ -672,10 +644,20 @@
 	if (pipe_ctx == NULL)
 		return;
 
-	if (dc_is_hdmi_signal(pipe_ctx->stream->signal) && pipe_ctx->stream_res.stream_enc != NULL)
+	if (dc_is_hdmi_signal(pipe_ctx->stream->signal) && pipe_ctx->stream_res.stream_enc != NULL) {
 		pipe_ctx->stream_res.stream_enc->funcs->set_avmute(
 				pipe_ctx->stream_res.stream_enc,
 				enable);
+
+		/* Wait for two frame to make sure AV mute is sent out */
+		if (enable) {
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VACTIVE);
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VBLANK);
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VACTIVE);
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VBLANK);
+			pipe_ctx->stream_res.tg->funcs->wait_for_state(pipe_ctx->stream_res.tg, CRTC_STATE_VACTIVE);
+		}
+	}
 }
 
 void dcn30_update_info_frame(struct pipe_ctx *pipe_ctx)
@@ -769,6 +751,9 @@
 			stream = dc->current_state->streams[0];
 			plane = (stream ? dc->current_state->stream_status[0].plane_states[0] : NULL);
 
+			if (!stream || !plane)
+				return false;
+
 			if (stream && plane) {
 				cursor_cache_enable = stream->cursor_position.enable &&
 						plane->address.grph.cursor_cache_addr.quad_part;
@@ -1002,7 +987,8 @@
 		/* turning off DPG */
 		pipe_ctx->plane_res.hubp->funcs->set_blank(pipe_ctx->plane_res.hubp, false);
 		for (mpcc_pipe = pipe_ctx->bottom_pipe; mpcc_pipe; mpcc_pipe = mpcc_pipe->bottom_pipe)
-			mpcc_pipe->plane_res.hubp->funcs->set_blank(mpcc_pipe->plane_res.hubp, false);
+			if (mpcc_pipe->plane_res.hubp)
+				mpcc_pipe->plane_res.hubp->funcs->set_blank(mpcc_pipe->plane_res.hubp, false);
 
 		stream_res->opp->funcs->opp_set_disp_pattern_generator(stream_res->opp, test_pattern, color_space,
 				color_depth, solid_color, width, height, offset);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_resource.c
@@ -840,7 +840,7 @@
 	.timing_trace = false,
 	.clock_trace = true,
 	.disable_pplib_clock_request = true,
-	.pipe_split_policy = MPC_SPLIT_AVOID_MULT_DISP,
+	.pipe_split_policy = MPC_SPLIT_DYNAMIC,
 	.force_single_disp_pipe_split = false,
 	.disable_dcc = DCC_ENABLE,
 	.vsr_support = true,
@@ -1164,8 +1164,12 @@
 	vpg = dcn30_vpg_create(ctx, vpg_inst);
 	afmt = dcn30_afmt_create(ctx, afmt_inst);
 
-	if (!enc1 || !vpg || !afmt)
+	if (!enc1 || !vpg || !afmt) {
+		kfree(enc1);
+		kfree(vpg);
+		kfree(afmt);
 		return NULL;
+	}
 
 	dcn30_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios,
 					eng_id, vpg, afmt,
@@ -1856,7 +1860,7 @@
 	return pipe;
 }
 
-static noinline bool dcn30_internal_validate_bw(
+noinline bool dcn30_internal_validate_bw(
 		struct dc *dc,
 		struct dc_state *context,
 		display_e2e_pipe_params_st *pipes,
@@ -1879,7 +1883,6 @@
 	dc->res_pool->funcs->update_soc_for_wm_a(dc, context);
 	pipe_cnt = dc->res_pool->funcs->populate_dml_pipes(dc, context, pipes, fast_validate);
 
-	DC_FP_START();
 	if (!pipe_cnt) {
 		out = true;
 		goto validate_out;
@@ -2103,7 +2106,6 @@
 	out = false;
 
 validate_out:
-	DC_FP_END();
 	return out;
 }
 
@@ -2304,7 +2306,9 @@
 
 	BW_VAL_TRACE_COUNT();
 
+	DC_FP_START();
 	out = dcn30_internal_validate_bw(dc, context, pipes, &pipe_cnt, &vlevel, fast_validate);
+	DC_FP_END();
 
 	if (pipe_cnt == 0)
 		goto validate_out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_resource.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn30/dcn30_resource.h
@@ -55,6 +55,13 @@
 
 bool dcn30_validate_bandwidth(struct dc *dc, struct dc_state *context,
 		bool fast_validate);
+bool dcn30_internal_validate_bw(
+		struct dc *dc,
+		struct dc_state *context,
+		display_e2e_pipe_params_st *pipes,
+		int *pipe_cnt_out,
+		int *vlevel_out,
+		bool fast_validate);
 void dcn30_calculate_wm_and_dlg(
 		struct dc *dc, struct dc_state *context,
 		display_e2e_pipe_params_st *pipes,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn301/dcn301_hubbub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn301/dcn301_hubbub.c
@@ -60,6 +60,7 @@
 	.program_watermarks = hubbub3_program_watermarks,
 	.allow_self_refresh_control = hubbub1_allow_self_refresh_control,
 	.is_allow_self_refresh_enabled = hubbub1_is_allow_self_refresh_enabled,
+	.verify_allow_pstate_change_high = hubbub1_verify_allow_pstate_change_high,
 	.force_wm_propagate_to_pipes = hubbub3_force_wm_propagate_to_pipes,
 	.force_pstate_change_control = hubbub3_force_pstate_change_control,
 	.hubbub_read_state = hubbub2_read_state,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn301/dcn301_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn301/dcn301_resource.c
@@ -863,7 +863,7 @@
 	.disable_clock_gate = true,
 	.disable_pplib_clock_request = true,
 	.disable_pplib_wm_range = true,
-	.pipe_split_policy = MPC_SPLIT_AVOID_MULT_DISP,
+	.pipe_split_policy = MPC_SPLIT_AVOID,
 	.force_single_disp_pipe_split = false,
 	.disable_dcc = DCC_ENABLE,
 	.vsr_support = true,
@@ -1195,8 +1195,12 @@
 	vpg = dcn301_vpg_create(ctx, vpg_inst);
 	afmt = dcn301_afmt_create(ctx, afmt_inst);
 
-	if (!enc1 || !vpg || !afmt)
+	if (!enc1 || !vpg || !afmt || eng_id >= ARRAY_SIZE(stream_enc_regs)) {
+		kfree(enc1);
+		kfree(vpg);
+		kfree(afmt);
 		return NULL;
+	}
 
 	dcn30_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios,
 					eng_id, vpg, afmt,
@@ -1622,12 +1626,106 @@
 	dml_init_instance(&dc->dml, &dcn3_01_soc, &dcn3_01_ip, DML_PROJECT_DCN30);
 }
 
+static void calculate_wm_set_for_vlevel(
+		int vlevel,
+		struct wm_range_table_entry *table_entry,
+		struct dcn_watermarks *wm_set,
+		struct display_mode_lib *dml,
+		display_e2e_pipe_params_st *pipes,
+		int pipe_cnt)
+{
+	double dram_clock_change_latency_cached = dml->soc.dram_clock_change_latency_us;
+
+	ASSERT(vlevel < dml->soc.num_states);
+	/* only pipe 0 is read for voltage and dcf/soc clocks */
+	pipes[0].clks_cfg.voltage = vlevel;
+	pipes[0].clks_cfg.dcfclk_mhz = dml->soc.clock_limits[vlevel].dcfclk_mhz;
+	pipes[0].clks_cfg.socclk_mhz = dml->soc.clock_limits[vlevel].socclk_mhz;
+
+	dml->soc.dram_clock_change_latency_us = table_entry->pstate_latency_us;
+	dml->soc.sr_exit_time_us = table_entry->sr_exit_time_us;
+	dml->soc.sr_enter_plus_exit_time_us = table_entry->sr_enter_plus_exit_time_us;
+
+	wm_set->urgent_ns = get_wm_urgent(dml, pipes, pipe_cnt) * 1000;
+	wm_set->cstate_pstate.cstate_enter_plus_exit_ns = get_wm_stutter_enter_exit(dml, pipes, pipe_cnt) * 1000;
+	wm_set->cstate_pstate.cstate_exit_ns = get_wm_stutter_exit(dml, pipes, pipe_cnt) * 1000;
+	wm_set->cstate_pstate.pstate_change_ns = get_wm_dram_clock_change(dml, pipes, pipe_cnt) * 1000;
+	wm_set->pte_meta_urgent_ns = get_wm_memory_trip(dml, pipes, pipe_cnt) * 1000;
+	wm_set->frac_urg_bw_nom = get_fraction_of_urgent_bandwidth(dml, pipes, pipe_cnt) * 1000;
+	wm_set->frac_urg_bw_flip = get_fraction_of_urgent_bandwidth_imm_flip(dml, pipes, pipe_cnt) * 1000;
+	wm_set->urgent_latency_ns = get_urgent_latency(dml, pipes, pipe_cnt) * 1000;
+	dml->soc.dram_clock_change_latency_us = dram_clock_change_latency_cached;
+
+}
+
+static void dcn301_calculate_wm_and_dlg(
+		struct dc *dc, struct dc_state *context,
+		display_e2e_pipe_params_st *pipes,
+		int pipe_cnt,
+		int vlevel_req)
+{
+	int i, pipe_idx;
+	int vlevel, vlevel_max;
+	struct wm_range_table_entry *table_entry;
+	struct clk_bw_params *bw_params = dc->clk_mgr->bw_params;
+
+	ASSERT(bw_params);
+
+	vlevel_max = bw_params->clk_table.num_entries - 1;
+
+	/* WM Set D */
+	table_entry = &bw_params->wm_table.entries[WM_D];
+	if (table_entry->wm_type == WM_TYPE_RETRAINING)
+		vlevel = 0;
+	else
+		vlevel = vlevel_max;
+	calculate_wm_set_for_vlevel(vlevel, table_entry, &context->bw_ctx.bw.dcn.watermarks.d,
+						&context->bw_ctx.dml, pipes, pipe_cnt);
+	/* WM Set C */
+	table_entry = &bw_params->wm_table.entries[WM_C];
+	vlevel = min(max(vlevel_req, 2), vlevel_max);
+	calculate_wm_set_for_vlevel(vlevel, table_entry, &context->bw_ctx.bw.dcn.watermarks.c,
+						&context->bw_ctx.dml, pipes, pipe_cnt);
+	/* WM Set B */
+	table_entry = &bw_params->wm_table.entries[WM_B];
+	vlevel = min(max(vlevel_req, 1), vlevel_max);
+	calculate_wm_set_for_vlevel(vlevel, table_entry, &context->bw_ctx.bw.dcn.watermarks.b,
+						&context->bw_ctx.dml, pipes, pipe_cnt);
+
+	/* WM Set A */
+	table_entry = &bw_params->wm_table.entries[WM_A];
+	vlevel = min(vlevel_req, vlevel_max);
+	calculate_wm_set_for_vlevel(vlevel, table_entry, &context->bw_ctx.bw.dcn.watermarks.a,
+						&context->bw_ctx.dml, pipes, pipe_cnt);
+
+	for (i = 0, pipe_idx = 0; i < dc->res_pool->pipe_count; i++) {
+		if (!context->res_ctx.pipe_ctx[i].stream)
+			continue;
+
+		pipes[pipe_idx].clks_cfg.dispclk_mhz = get_dispclk_calculated(&context->bw_ctx.dml, pipes, pipe_cnt);
+		pipes[pipe_idx].clks_cfg.dppclk_mhz = get_dppclk_calculated(&context->bw_ctx.dml, pipes, pipe_cnt, pipe_idx);
+
+		if (dc->config.forced_clocks) {
+			pipes[pipe_idx].clks_cfg.dispclk_mhz = context->bw_ctx.dml.soc.clock_limits[0].dispclk_mhz;
+			pipes[pipe_idx].clks_cfg.dppclk_mhz = context->bw_ctx.dml.soc.clock_limits[0].dppclk_mhz;
+		}
+		if (dc->debug.min_disp_clk_khz > pipes[pipe_idx].clks_cfg.dispclk_mhz * 1000)
+			pipes[pipe_idx].clks_cfg.dispclk_mhz = dc->debug.min_disp_clk_khz / 1000.0;
+		if (dc->debug.min_dpp_clk_khz > pipes[pipe_idx].clks_cfg.dppclk_mhz * 1000)
+			pipes[pipe_idx].clks_cfg.dppclk_mhz = dc->debug.min_dpp_clk_khz / 1000.0;
+
+		pipe_idx++;
+	}
+
+	dcn20_calculate_dlg_params(dc, context, pipes, pipe_cnt, vlevel);
+}
+
 static struct resource_funcs dcn301_res_pool_funcs = {
 	.destroy = dcn301_destroy_resource_pool,
 	.link_enc_create = dcn301_link_encoder_create,
 	.panel_cntl_create = dcn301_panel_cntl_create,
 	.validate_bandwidth = dcn30_validate_bandwidth,
-	.calculate_wm_and_dlg = dcn30_calculate_wm_and_dlg,
+	.calculate_wm_and_dlg = dcn301_calculate_wm_and_dlg,
 	.update_soc_for_wm_a = dcn30_update_soc_for_wm_a,
 	.populate_dml_pipes = dcn30_populate_dml_pipes_from_context,
 	.acquire_idle_pipe_for_layer = dcn20_acquire_idle_pipe_for_layer,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c
@@ -211,7 +211,7 @@
 		.timing_trace = false,
 		.clock_trace = true,
 		.disable_pplib_clock_request = true,
-		.pipe_split_policy = MPC_SPLIT_AVOID_MULT_DISP,
+		.pipe_split_policy = MPC_SPLIT_DYNAMIC,
 		.force_single_disp_pipe_split = false,
 		.disable_dcc = DCC_ENABLE,
 		.vsr_support = true,
@@ -542,8 +542,12 @@
 	vpg = dcn302_vpg_create(ctx, vpg_inst);
 	afmt = dcn302_afmt_create(ctx, afmt_inst);
 
-	if (!enc1 || !vpg || !afmt)
+	if (!enc1 || !vpg || !afmt) {
+		kfree(enc1);
+		kfree(vpg);
+		kfree(afmt);
 		return NULL;
+	}
 
 	dcn30_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios, eng_id, vpg, afmt, &stream_enc_regs[eng_id],
 			&se_shift, &se_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn303/dcn303_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn303/dcn303_resource.c
@@ -193,7 +193,7 @@
 		.timing_trace = false,
 		.clock_trace = true,
 		.disable_pplib_clock_request = true,
-		.pipe_split_policy = MPC_SPLIT_AVOID_MULT_DISP,
+		.pipe_split_policy = MPC_SPLIT_AVOID,
 		.force_single_disp_pipe_split = false,
 		.disable_dcc = DCC_ENABLE,
 		.vsr_support = true,
@@ -500,7 +500,7 @@
 	int afmt_inst;
 
 	/* Mapping of VPG, AFMT, DME register blocks to DIO block instance */
-	if (eng_id <= ENGINE_ID_DIGE) {
+	if (eng_id <= ENGINE_ID_DIGB) {
 		vpg_inst = eng_id;
 		afmt_inst = eng_id;
 	} else
@@ -1344,6 +1344,20 @@
 			dcn3_03_soc.clock_limits[i].phyclk_d18_mhz = dcn3_03_soc.clock_limits[0].phyclk_d18_mhz;
 			dcn3_03_soc.clock_limits[i].dscclk_mhz = dcn3_03_soc.clock_limits[0].dscclk_mhz;
 		}
+
+		// WA: patch strobe modes to compensate for DCN303 BW issue
+		if (dcn3_03_soc.num_chans <= 4) {
+			for (i = 0; i < dcn3_03_soc.num_states; i++) {
+				if (dcn3_03_soc.clock_limits[i].dram_speed_mts > 1700)
+					break;
+
+				if (dcn3_03_soc.clock_limits[i].dram_speed_mts >= 1500) {
+					dcn3_03_soc.clock_limits[i].dcfclk_mhz = 100;
+					dcn3_03_soc.clock_limits[i].fabricclk_mhz = 100;
+				}
+			}
+		}
+
 		/* re-init DML with updated bb */
 		dml_init_instance(&dc->dml, &dcn3_03_soc, &dcn3_03_ip, DML_PROJECT_DCN30);
 		if (dc->current_state)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dio_link_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dio_link_encoder.c
@@ -67,6 +67,68 @@
 #define MIN(X, Y) ((X) < (Y) ? (X) : (Y))
 #endif
 
+static uint8_t phy_id_from_transmitter(enum transmitter t)
+{
+	uint8_t phy_id;
+
+	switch (t) {
+	case TRANSMITTER_UNIPHY_A:
+		phy_id = 0;
+		break;
+	case TRANSMITTER_UNIPHY_B:
+		phy_id = 1;
+		break;
+	case TRANSMITTER_UNIPHY_C:
+		phy_id = 2;
+		break;
+	case TRANSMITTER_UNIPHY_D:
+		phy_id = 3;
+		break;
+	case TRANSMITTER_UNIPHY_E:
+		phy_id = 4;
+		break;
+	case TRANSMITTER_UNIPHY_F:
+		phy_id = 5;
+		break;
+	case TRANSMITTER_UNIPHY_G:
+		phy_id = 6;
+		break;
+	default:
+		phy_id = 0;
+		break;
+	}
+	return phy_id;
+}
+
+static bool has_query_dp_alt(struct link_encoder *enc)
+{
+	struct dc_dmub_srv *dc_dmub_srv = enc->ctx->dmub_srv;
+
+	/* Supports development firmware and firmware >= 4.0.11 */
+	return dc_dmub_srv &&
+	       !(dc_dmub_srv->dmub->fw_version >= DMUB_FW_VERSION(4, 0, 0) &&
+		 dc_dmub_srv->dmub->fw_version <= DMUB_FW_VERSION(4, 0, 10));
+}
+
+static bool query_dp_alt_from_dmub(struct link_encoder *enc,
+				   union dmub_rb_cmd *cmd)
+{
+	struct dcn10_link_encoder *enc10 = TO_DCN10_LINK_ENC(enc);
+	struct dc_dmub_srv *dc_dmub_srv = enc->ctx->dmub_srv;
+
+	memset(cmd, 0, sizeof(*cmd));
+	cmd->query_dp_alt.header.type = DMUB_CMD__VBIOS;
+	cmd->query_dp_alt.header.sub_type =
+		DMUB_CMD__VBIOS_TRANSMITTER_QUERY_DP_ALT;
+	cmd->query_dp_alt.header.payload_bytes = sizeof(cmd->query_dp_alt.data);
+	cmd->query_dp_alt.data.phy_id = phy_id_from_transmitter(enc10->base.transmitter);
+
+	if (!dc_dmub_srv_cmd_with_reply_data(dc_dmub_srv, cmd))
+		return false;
+
+	return true;
+}
+
 void dcn31_link_encoder_set_dio_phy_mux(
 	struct link_encoder *enc,
 	enum encoder_type_select sel,
@@ -168,9 +230,7 @@
 	AUX_RX_PHASE_DETECT_LEN,  [21,20] = 0x3 default is 3
 	AUX_RX_DETECTION_THRESHOLD [30:28] = 1
 */
-	AUX_REG_WRITE(AUX_DPHY_RX_CONTROL0, 0x103d1110);
-
-	AUX_REG_WRITE(AUX_DPHY_TX_CONTROL, 0x21c7a);
+	// dmub will read AUX_DPHY_RX_CONTROL0/AUX_DPHY_TX_CONTROL from vbios table in dp_aux_init
 
 	//AUX_DPHY_TX_REF_CONTROL'AUX_TX_REF_DIV HW default is 0x32;
 	// Set AUX_TX_REF_DIV Divider to generate 2 MHz reference from refclk
@@ -362,19 +422,79 @@
 		SIGNAL_TYPE_EDP;
 }
 
+/* DPIA equivalent of link_transmitter_control. */
+static bool link_dpia_control(struct dc_context *dc_ctx,
+	struct dmub_cmd_dig_dpia_control_data *dpia_control)
+{
+	union dmub_rb_cmd cmd;
+	struct dc_dmub_srv *dmub = dc_ctx->dmub_srv;
+
+	memset(&cmd, 0, sizeof(cmd));
+
+	cmd.dig1_dpia_control.header.type = DMUB_CMD__DPIA;
+	cmd.dig1_dpia_control.header.sub_type =
+			DMUB_CMD__DPIA_DIG1_DPIA_CONTROL;
+	cmd.dig1_dpia_control.header.payload_bytes =
+		sizeof(cmd.dig1_dpia_control) -
+		sizeof(cmd.dig1_dpia_control.header);
+
+	cmd.dig1_dpia_control.dpia_control = *dpia_control;
+
+	dc_dmub_srv_cmd_queue(dmub, &cmd);
+	dc_dmub_srv_cmd_execute(dmub);
+	dc_dmub_srv_wait_idle(dmub);
+
+	return true;
+}
+
+static void link_encoder_disable(struct dcn10_link_encoder *enc10)
+{
+	/* reset training complete */
+	REG_UPDATE(DP_LINK_CNTL, DP_LINK_TRAINING_COMPLETE, 0);
+}
+
 void dcn31_link_encoder_enable_dp_output(
 	struct link_encoder *enc,
 	const struct dc_link_settings *link_settings,
 	enum clock_source_id clock_source)
 {
+	struct dcn10_link_encoder *enc10 = TO_DCN10_LINK_ENC(enc);
+
 	/* Enable transmitter and encoder. */
-	if (!link_enc_cfg_is_transmitter_mappable(enc->ctx->dc->current_state, enc)) {
+	if (!link_enc_cfg_is_transmitter_mappable(enc->ctx->dc, enc)) {
 
 		dcn20_link_encoder_enable_dp_output(enc, link_settings, clock_source);
 
 	} else {
 
-		/** @todo Handle transmitter with programmable mapping to link encoder. */
+		struct dmub_cmd_dig_dpia_control_data dpia_control = { 0 };
+		struct dc_link *link;
+
+		link = link_enc_cfg_get_link_using_link_enc(enc->ctx->dc, enc->preferred_engine);
+
+		enc1_configure_encoder(enc10, link_settings);
+
+		dpia_control.action = (uint8_t)TRANSMITTER_CONTROL_ENABLE;
+		dpia_control.enc_id = enc->preferred_engine;
+		dpia_control.mode_laneset.digmode = 0; /* 0 for SST; 5 for MST */
+		dpia_control.lanenum = (uint8_t)link_settings->lane_count;
+		dpia_control.symclk_10khz = link_settings->link_rate *
+				LINK_RATE_REF_FREQ_IN_KHZ / 10;
+		/* DIG_BE_CNTL.DIG_HPD_SELECT set to 5 (hpdsel - 1) to indicate HPD pin
+		 * unused by DPIA.
+		 */
+		dpia_control.hpdsel = 6;
+
+		if (link) {
+			dpia_control.dpia_id = link->ddc_hw_inst;
+			dpia_control.fec_rdy = dc_link_should_enable_fec(link);
+		} else {
+			DC_LOG_ERROR("%s: Failed to execute DPIA enable DMUB command.\n", __func__);
+			BREAK_TO_DEBUGGER();
+			return;
+		}
+
+		link_dpia_control(enc->ctx, &dpia_control);
 	}
 }
 
@@ -383,14 +503,43 @@
 	const struct dc_link_settings *link_settings,
 	enum clock_source_id clock_source)
 {
+	struct dcn10_link_encoder *enc10 = TO_DCN10_LINK_ENC(enc);
+
 	/* Enable transmitter and encoder. */
-	if (!link_enc_cfg_is_transmitter_mappable(enc->ctx->dc->current_state, enc)) {
+	if (!link_enc_cfg_is_transmitter_mappable(enc->ctx->dc, enc)) {
 
 		dcn10_link_encoder_enable_dp_mst_output(enc, link_settings, clock_source);
 
 	} else {
 
-		/** @todo Handle transmitter with programmable mapping to link encoder. */
+		struct dmub_cmd_dig_dpia_control_data dpia_control = { 0 };
+		struct dc_link *link;
+
+		link = link_enc_cfg_get_link_using_link_enc(enc->ctx->dc, enc->preferred_engine);
+
+		enc1_configure_encoder(enc10, link_settings);
+
+		dpia_control.action = (uint8_t)TRANSMITTER_CONTROL_ENABLE;
+		dpia_control.enc_id = enc->preferred_engine;
+		dpia_control.mode_laneset.digmode = 5; /* 0 for SST; 5 for MST */
+		dpia_control.lanenum = (uint8_t)link_settings->lane_count;
+		dpia_control.symclk_10khz = link_settings->link_rate *
+				LINK_RATE_REF_FREQ_IN_KHZ / 10;
+		/* DIG_BE_CNTL.DIG_HPD_SELECT set to 5 (hpdsel - 1) to indicate HPD pin
+		 * unused by DPIA.
+		 */
+		dpia_control.hpdsel = 6;
+
+		if (link) {
+			dpia_control.dpia_id = link->ddc_hw_inst;
+			dpia_control.fec_rdy = dc_link_should_enable_fec(link);
+		} else {
+			DC_LOG_ERROR("%s: Failed to execute DPIA enable DMUB command.\n", __func__);
+			BREAK_TO_DEBUGGER();
+			return;
+		}
+
+		link_dpia_control(enc->ctx, &dpia_control);
 	}
 }
 
@@ -398,71 +547,135 @@
 	struct link_encoder *enc,
 	enum signal_type signal)
 {
+	struct dcn10_link_encoder *enc10 = TO_DCN10_LINK_ENC(enc);
+
 	/* Disable transmitter and encoder. */
-	if (!link_enc_cfg_is_transmitter_mappable(enc->ctx->dc->current_state, enc)) {
+	if (!link_enc_cfg_is_transmitter_mappable(enc->ctx->dc, enc)) {
 
 		dcn10_link_encoder_disable_output(enc, signal);
 
 	} else {
 
-		/** @todo Handle transmitter with programmable mapping to link encoder. */
+		struct dmub_cmd_dig_dpia_control_data dpia_control = { 0 };
+		struct dc_link *link;
+
+		if (!dcn10_is_dig_enabled(enc))
+			return;
+
+		link = link_enc_cfg_get_link_using_link_enc(enc->ctx->dc, enc->preferred_engine);
+
+		dpia_control.action = (uint8_t)TRANSMITTER_CONTROL_DISABLE;
+		dpia_control.enc_id = enc->preferred_engine;
+		if (signal == SIGNAL_TYPE_DISPLAY_PORT) {
+			dpia_control.mode_laneset.digmode = 0; /* 0 for SST; 5 for MST */
+		} else if (signal == SIGNAL_TYPE_DISPLAY_PORT_MST) {
+			dpia_control.mode_laneset.digmode = 5; /* 0 for SST; 5 for MST */
+		} else {
+			DC_LOG_ERROR("%s: USB4 DPIA only supports DisplayPort.\n", __func__);
+			BREAK_TO_DEBUGGER();
+		}
+
+		if (link) {
+			dpia_control.dpia_id = link->ddc_hw_inst;
+		} else {
+			DC_LOG_ERROR("%s: Failed to execute DPIA enable DMUB command.\n", __func__);
+			BREAK_TO_DEBUGGER();
+			return;
+		}
+
+		link_dpia_control(enc->ctx, &dpia_control);
+
+		link_encoder_disable(enc10);
 	}
 }
 
 bool dcn31_link_encoder_is_in_alt_mode(struct link_encoder *enc)
 {
 	struct dcn10_link_encoder *enc10 = TO_DCN10_LINK_ENC(enc);
+	union dmub_rb_cmd cmd;
 	uint32_t dp_alt_mode_disable;
-	bool is_usb_c_alt_mode = false;
 
-	if (enc->features.flags.bits.DP_IS_USB_C) {
-		if (enc->ctx->asic_id.hw_internal_rev != YELLOW_CARP_B0) {
-			// [Note] no need to check hw_internal_rev once phy mux selection is ready
-			REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DISABLE, &dp_alt_mode_disable);
-		} else {
+	/* Only applicable to USB-C PHY. */
+	if (!enc->features.flags.bits.DP_IS_USB_C)
+		return false;
+
+	/*
+	 * Use the new interface from DMCUB if available.
+	 * Avoids hanging the RDCPSPIPE if DMCUB wasn't already running.
+	 */
+	if (has_query_dp_alt(enc)) {
+		if (!query_dp_alt_from_dmub(enc, &cmd))
+			return false;
+
+		return (cmd.query_dp_alt.data.is_dp_alt_disable == 0);
+	}
+
+	/* Legacy path, avoid if possible. */
+	if (enc->ctx->asic_id.hw_internal_rev != YELLOW_CARP_B0) {
+		REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DISABLE,
+			&dp_alt_mode_disable);
+	} else {
 		/*
 		 * B0 phys use a new set of registers to check whether alt mode is disabled.
 		 * if value == 1 alt mode is disabled, otherwise it is enabled.
 		 */
-			if ((enc10->base.transmitter == TRANSMITTER_UNIPHY_A)
-					|| (enc10->base.transmitter == TRANSMITTER_UNIPHY_B)
-					|| (enc10->base.transmitter == TRANSMITTER_UNIPHY_E)) {
-				REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DISABLE, &dp_alt_mode_disable);
-			} else {
-			// [Note] need to change TRANSMITTER_UNIPHY_C/D to F/G once phy mux selection is ready
-				REG_GET(RDPCSPIPE_PHY_CNTL6, RDPCS_PHY_DPALT_DISABLE, &dp_alt_mode_disable);
-			}
+		if ((enc10->base.transmitter == TRANSMITTER_UNIPHY_A) ||
+		    (enc10->base.transmitter == TRANSMITTER_UNIPHY_B) ||
+		    (enc10->base.transmitter == TRANSMITTER_UNIPHY_E)) {
+			REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DISABLE,
+				&dp_alt_mode_disable);
+		} else {
+			REG_GET(RDPCSPIPE_PHY_CNTL6, RDPCS_PHY_DPALT_DISABLE,
+				&dp_alt_mode_disable);
 		}
-
-		is_usb_c_alt_mode = (dp_alt_mode_disable == 0);
 	}
 
-	return is_usb_c_alt_mode;
+	return (dp_alt_mode_disable == 0);
 }
 
-void dcn31_link_encoder_get_max_link_cap(struct link_encoder *enc,
-										 struct dc_link_settings *link_settings)
+void dcn31_link_encoder_get_max_link_cap(struct link_encoder *enc, struct dc_link_settings *link_settings)
 {
 	struct dcn10_link_encoder *enc10 = TO_DCN10_LINK_ENC(enc);
+	union dmub_rb_cmd cmd;
 	uint32_t is_in_usb_c_dp4_mode = 0;
 
 	dcn10_link_encoder_get_max_link_cap(enc, link_settings);
 
-	/* in usb c dp2 mode, max lane count is 2 */
-	if (enc->funcs->is_in_alt_mode && enc->funcs->is_in_alt_mode(enc)) {
-		if (enc->ctx->asic_id.hw_internal_rev != YELLOW_CARP_B0) {
-			// [Note] no need to check hw_internal_rev once phy mux selection is ready
-			REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DP4, &is_in_usb_c_dp4_mode);
+	/* Take the link cap directly if not USB */
+	if (!enc->features.flags.bits.DP_IS_USB_C)
+		return;
+
+	/*
+	 * Use the new interface from DMCUB if available.
+	 * Avoids hanging the RDCPSPIPE if DMCUB wasn't already running.
+	 */
+	if (has_query_dp_alt(enc)) {
+		if (!query_dp_alt_from_dmub(enc, &cmd))
+			return;
+
+		if (cmd.query_dp_alt.data.is_usb &&
+		    cmd.query_dp_alt.data.is_dp4 == 0)
+			link_settings->lane_count = MIN(LANE_COUNT_TWO, link_settings->lane_count);
+
+		return;
+	}
+
+	/* Legacy path, avoid if possible. */
+	if (enc->ctx->asic_id.hw_internal_rev != YELLOW_CARP_B0) {
+		REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DP4,
+			&is_in_usb_c_dp4_mode);
+	} else {
+		if ((enc10->base.transmitter == TRANSMITTER_UNIPHY_A) ||
+		    (enc10->base.transmitter == TRANSMITTER_UNIPHY_B) ||
+		    (enc10->base.transmitter == TRANSMITTER_UNIPHY_E)) {
+			REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DP4,
+				&is_in_usb_c_dp4_mode);
 		} else {
-			if ((enc10->base.transmitter == TRANSMITTER_UNIPHY_A)
-					|| (enc10->base.transmitter == TRANSMITTER_UNIPHY_B)
-					|| (enc10->base.transmitter == TRANSMITTER_UNIPHY_E)) {
-				REG_GET(RDPCSTX_PHY_CNTL6, RDPCS_PHY_DPALT_DP4, &is_in_usb_c_dp4_mode);
-			} else {
-				REG_GET(RDPCSPIPE_PHY_CNTL6, RDPCS_PHY_DPALT_DP4, &is_in_usb_c_dp4_mode);
-			}
+			REG_GET(RDPCSPIPE_PHY_CNTL6, RDPCS_PHY_DPALT_DP4,
+				&is_in_usb_c_dp4_mode);
 		}
-		if (!is_in_usb_c_dp4_mode)
-			link_settings->lane_count = MIN(LANE_COUNT_TWO, link_settings->lane_count);
 	}
+
+	if (!is_in_usb_c_dp4_mode)
+		link_settings->lane_count = MIN(LANE_COUNT_TWO, link_settings->lane_count);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hubbub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hubbub.c
@@ -24,6 +24,7 @@
  */
 
 
+#include <linux/delay.h>
 #include "dcn30/dcn30_hubbub.h"
 #include "dcn31_hubbub.h"
 #include "dm_services.h"
@@ -138,8 +139,11 @@
 	ret_val = wm_ns * refclk_mhz;
 	ret_val /= 1000;
 
-	if (ret_val > clamp_value)
+	if (ret_val > clamp_value) {
+		/* clamping WMs is abnormal, unexpected and may lead to underflow*/
+		ASSERT(0);
 		ret_val = clamp_value;
+	}
 
 	return ret_val;
 }
@@ -159,7 +163,7 @@
 	if (safe_to_lower || watermarks->a.urgent_ns > hubbub2->watermarks.a.urgent_ns) {
 		hubbub2->watermarks.a.urgent_ns = watermarks->a.urgent_ns;
 		prog_wm_value = convert_and_clamp(watermarks->a.urgent_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_A, 0,
 				DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_A, prog_wm_value);
 
@@ -193,7 +197,7 @@
 	if (safe_to_lower || watermarks->a.urgent_latency_ns > hubbub2->watermarks.a.urgent_latency_ns) {
 		hubbub2->watermarks.a.urgent_latency_ns = watermarks->a.urgent_latency_ns;
 		prog_wm_value = convert_and_clamp(watermarks->a.urgent_latency_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_A, 0,
 				DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_A, prog_wm_value);
 	} else if (watermarks->a.urgent_latency_ns < hubbub2->watermarks.a.urgent_latency_ns)
@@ -203,7 +207,7 @@
 	if (safe_to_lower || watermarks->b.urgent_ns > hubbub2->watermarks.b.urgent_ns) {
 		hubbub2->watermarks.b.urgent_ns = watermarks->b.urgent_ns;
 		prog_wm_value = convert_and_clamp(watermarks->b.urgent_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_B, 0,
 				DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_B, prog_wm_value);
 
@@ -237,7 +241,7 @@
 	if (safe_to_lower || watermarks->b.urgent_latency_ns > hubbub2->watermarks.b.urgent_latency_ns) {
 		hubbub2->watermarks.b.urgent_latency_ns = watermarks->b.urgent_latency_ns;
 		prog_wm_value = convert_and_clamp(watermarks->b.urgent_latency_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_B, 0,
 				DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_B, prog_wm_value);
 	} else if (watermarks->b.urgent_latency_ns < hubbub2->watermarks.b.urgent_latency_ns)
@@ -247,7 +251,7 @@
 	if (safe_to_lower || watermarks->c.urgent_ns > hubbub2->watermarks.c.urgent_ns) {
 		hubbub2->watermarks.c.urgent_ns = watermarks->c.urgent_ns;
 		prog_wm_value = convert_and_clamp(watermarks->c.urgent_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_C, 0,
 				DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_C, prog_wm_value);
 
@@ -281,7 +285,7 @@
 	if (safe_to_lower || watermarks->c.urgent_latency_ns > hubbub2->watermarks.c.urgent_latency_ns) {
 		hubbub2->watermarks.c.urgent_latency_ns = watermarks->c.urgent_latency_ns;
 		prog_wm_value = convert_and_clamp(watermarks->c.urgent_latency_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_C, 0,
 				DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_C, prog_wm_value);
 	} else if (watermarks->c.urgent_latency_ns < hubbub2->watermarks.c.urgent_latency_ns)
@@ -291,7 +295,7 @@
 	if (safe_to_lower || watermarks->d.urgent_ns > hubbub2->watermarks.d.urgent_ns) {
 		hubbub2->watermarks.d.urgent_ns = watermarks->d.urgent_ns;
 		prog_wm_value = convert_and_clamp(watermarks->d.urgent_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_D, 0,
 				DCHUBBUB_ARB_DATA_URGENCY_WATERMARK_D, prog_wm_value);
 
@@ -325,7 +329,7 @@
 	if (safe_to_lower || watermarks->d.urgent_latency_ns > hubbub2->watermarks.d.urgent_latency_ns) {
 		hubbub2->watermarks.d.urgent_latency_ns = watermarks->d.urgent_latency_ns;
 		prog_wm_value = convert_and_clamp(watermarks->d.urgent_latency_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0x3fff);
 		REG_SET(DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_D, 0,
 				DCHUBBUB_ARB_REFCYC_PER_TRIP_TO_MEMORY_D, prog_wm_value);
 	} else if (watermarks->d.urgent_latency_ns < hubbub2->watermarks.d.urgent_latency_ns)
@@ -351,7 +355,7 @@
 				watermarks->a.cstate_pstate.cstate_enter_plus_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->a.cstate_pstate.cstate_enter_plus_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_A, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_A, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_EXIT_WATERMARK_A calculated =%d\n"
@@ -367,7 +371,7 @@
 				watermarks->a.cstate_pstate.cstate_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->a.cstate_pstate.cstate_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_A, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_A, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_A calculated =%d\n"
@@ -383,7 +387,7 @@
 				watermarks->a.cstate_pstate.cstate_enter_plus_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->a.cstate_pstate.cstate_enter_plus_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_A, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_A, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_WATERMARK_Z8_A calculated =%d\n"
@@ -399,7 +403,7 @@
 				watermarks->a.cstate_pstate.cstate_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->a.cstate_pstate.cstate_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_A, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_A, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_Z8_A calculated =%d\n"
@@ -416,7 +420,7 @@
 				watermarks->b.cstate_pstate.cstate_enter_plus_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->b.cstate_pstate.cstate_enter_plus_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_B, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_B, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_EXIT_WATERMARK_B calculated =%d\n"
@@ -432,7 +436,7 @@
 				watermarks->b.cstate_pstate.cstate_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->b.cstate_pstate.cstate_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_B, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_B, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_B calculated =%d\n"
@@ -448,7 +452,7 @@
 				watermarks->b.cstate_pstate.cstate_enter_plus_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->b.cstate_pstate.cstate_enter_plus_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_B, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_B, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_WATERMARK_Z8_B calculated =%d\n"
@@ -464,7 +468,7 @@
 				watermarks->b.cstate_pstate.cstate_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->b.cstate_pstate.cstate_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_B, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_B, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_Z8_B calculated =%d\n"
@@ -481,7 +485,7 @@
 				watermarks->c.cstate_pstate.cstate_enter_plus_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->c.cstate_pstate.cstate_enter_plus_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_C, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_C, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_EXIT_WATERMARK_C calculated =%d\n"
@@ -497,7 +501,7 @@
 				watermarks->c.cstate_pstate.cstate_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->c.cstate_pstate.cstate_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_C, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_C, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_C calculated =%d\n"
@@ -513,7 +517,7 @@
 				watermarks->c.cstate_pstate.cstate_enter_plus_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->c.cstate_pstate.cstate_enter_plus_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_C, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_C, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_WATERMARK_Z8_C calculated =%d\n"
@@ -529,7 +533,7 @@
 				watermarks->c.cstate_pstate.cstate_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->c.cstate_pstate.cstate_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_C, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_C, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_Z8_C calculated =%d\n"
@@ -546,7 +550,7 @@
 				watermarks->d.cstate_pstate.cstate_enter_plus_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->d.cstate_pstate.cstate_enter_plus_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_D, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_D, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_EXIT_WATERMARK_D calculated =%d\n"
@@ -562,7 +566,7 @@
 				watermarks->d.cstate_pstate.cstate_exit_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->d.cstate_pstate.cstate_exit_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_D, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_D, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_D calculated =%d\n"
@@ -578,7 +582,7 @@
 				watermarks->d.cstate_pstate.cstate_enter_plus_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->d.cstate_pstate.cstate_enter_plus_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_D, 0,
 				DCHUBBUB_ARB_ALLOW_SR_ENTER_WATERMARK_Z8_D, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_ENTER_WATERMARK_Z8_D calculated =%d\n"
@@ -594,7 +598,7 @@
 				watermarks->d.cstate_pstate.cstate_exit_z8_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->d.cstate_pstate.cstate_exit_z8_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_D, 0,
 				DCHUBBUB_ARB_ALLOW_SR_EXIT_WATERMARK_Z8_D, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("SR_EXIT_WATERMARK_Z8_D calculated =%d\n"
@@ -625,7 +629,7 @@
 				watermarks->a.cstate_pstate.pstate_change_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->a.cstate_pstate.pstate_change_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_A, 0,
 				DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_A, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("DRAM_CLK_CHANGE_WATERMARK_A calculated =%d\n"
@@ -642,7 +646,7 @@
 				watermarks->b.cstate_pstate.pstate_change_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->b.cstate_pstate.pstate_change_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_B, 0,
 				DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_B, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("DRAM_CLK_CHANGE_WATERMARK_B calculated =%d\n"
@@ -659,7 +663,7 @@
 				watermarks->c.cstate_pstate.pstate_change_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->c.cstate_pstate.pstate_change_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_C, 0,
 				DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_C, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("DRAM_CLK_CHANGE_WATERMARK_C calculated =%d\n"
@@ -676,7 +680,7 @@
 				watermarks->d.cstate_pstate.pstate_change_ns;
 		prog_wm_value = convert_and_clamp(
 				watermarks->d.cstate_pstate.pstate_change_ns,
-				refclk_mhz, 0x1fffff);
+				refclk_mhz, 0xffff);
 		REG_SET(DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_D, 0,
 				DCHUBBUB_ARB_ALLOW_DRAM_CLK_CHANGE_WATERMARK_D, prog_wm_value);
 		DC_LOG_BANDWIDTH_CALCS("DRAM_CLK_CHANGE_WATERMARK_D calculated =%d\n"
@@ -946,6 +950,65 @@
 	}
 }
 
+static bool hubbub31_verify_allow_pstate_change_high(struct hubbub *hubbub)
+{
+	struct dcn20_hubbub *hubbub2 = TO_DCN20_HUBBUB(hubbub);
+
+	/*
+	 * Pstate latency is ~20us so if we wait over 40us and pstate allow
+	 * still not asserted, we are probably stuck and going to hang
+	 */
+	const unsigned int pstate_wait_timeout_us = 100;
+	const unsigned int pstate_wait_expected_timeout_us = 40;
+
+	static unsigned int max_sampled_pstate_wait_us; /* data collection */
+	static bool forced_pstate_allow; /* help with revert wa */
+
+	unsigned int debug_data = 0;
+	unsigned int i;
+
+	if (forced_pstate_allow) {
+		/* we hacked to force pstate allow to prevent hang last time
+		 * we verify_allow_pstate_change_high.  so disable force
+		 * here so we can check status
+		 */
+		REG_UPDATE_2(DCHUBBUB_ARB_DRAM_STATE_CNTL,
+			     DCHUBBUB_ARB_ALLOW_PSTATE_CHANGE_FORCE_VALUE, 0,
+			     DCHUBBUB_ARB_ALLOW_PSTATE_CHANGE_FORCE_ENABLE, 0);
+		forced_pstate_allow = false;
+	}
+
+	REG_WRITE(DCHUBBUB_TEST_DEBUG_INDEX, hubbub2->debug_test_index_pstate);
+
+	for (i = 0; i < pstate_wait_timeout_us; i++) {
+		debug_data = REG_READ(DCHUBBUB_TEST_DEBUG_DATA);
+
+		/* Debug bit is specific to ASIC. */
+		if (debug_data & (1 << 26)) {
+			if (i > pstate_wait_expected_timeout_us)
+				DC_LOG_WARNING("pstate took longer than expected ~%dus\n", i);
+			return true;
+		}
+		if (max_sampled_pstate_wait_us < i)
+			max_sampled_pstate_wait_us = i;
+
+		udelay(1);
+	}
+
+	/* force pstate allow to prevent system hang
+	 * and break to debugger to investigate
+	 */
+	REG_UPDATE_2(DCHUBBUB_ARB_DRAM_STATE_CNTL,
+		     DCHUBBUB_ARB_ALLOW_PSTATE_CHANGE_FORCE_VALUE, 1,
+		     DCHUBBUB_ARB_ALLOW_PSTATE_CHANGE_FORCE_ENABLE, 1);
+	forced_pstate_allow = true;
+
+	DC_LOG_WARNING("pstate TEST_DEBUG_DATA: 0x%X\n",
+			debug_data);
+
+	return false;
+}
+
 static const struct hubbub_funcs hubbub31_funcs = {
 	.update_dchub = hubbub2_update_dchub,
 	.init_dchub_sys_ctx = hubbub31_init_dchub_sys_ctx,
@@ -958,6 +1021,7 @@
 	.program_watermarks = hubbub31_program_watermarks,
 	.allow_self_refresh_control = hubbub1_allow_self_refresh_control,
 	.is_allow_self_refresh_enabled = hubbub1_is_allow_self_refresh_enabled,
+	.verify_allow_pstate_change_high = hubbub31_verify_allow_pstate_change_high,
 	.program_det_size = dcn31_program_det_size,
 	.program_compbuf_size = dcn31_program_compbuf_size,
 	.init_crb = dcn31_init_crb,
@@ -979,5 +1043,7 @@
 	hubbub31->detile_buf_size = det_size_kb * 1024;
 	hubbub31->pixel_chunk_size = pixel_chunk_size_kb * 1024;
 	hubbub31->crb_size_segs = config_return_buffer_size_kb / DCN31_CRB_SEGMENT_SIZE_KB;
+
+	hubbub31->debug_test_index_pstate = 0x6;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hubp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hubp.c
@@ -79,6 +79,7 @@
 	.hubp_init = hubp3_init,
 	.set_unbounded_requesting = hubp31_set_unbounded_requesting,
 	.hubp_soft_reset = hubp31_soft_reset,
+	.hubp_set_flip_int = hubp1_set_flip_int,
 	.hubp_in_blank = hubp1_in_blank,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hwseq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hwseq.c
@@ -48,6 +48,7 @@
 #include "dc_link_dp.h"
 #include "inc/link_dpcd.h"
 #include "dcn10/dcn10_hw_sequencer.h"
+#include "inc/link_enc_cfg.h"
 
 #define DC_LOGGER_INIT(logger)
 
@@ -70,7 +71,7 @@
 	struct dc_bios *dcb = dc->ctx->dc_bios;
 	struct resource_pool *res_pool = dc->res_pool;
 	uint32_t backlight = MAX_BACKLIGHT_LEVEL;
-	int i, j;
+	int i;
 	int edp_num;
 
 	if (dc->clk_mgr && dc->clk_mgr->funcs->init_clocks)
@@ -156,6 +157,9 @@
 		 */
 		struct dc_link *link = dc->links[i];
 
+		if (link->ep_type != DISPLAY_ENDPOINT_PHY)
+			continue;
+
 		link->link_enc->funcs->hw_init(link->link_enc);
 
 		/* Check for enabled DIG to identify enabled display */
@@ -169,40 +173,16 @@
 		if (hws->funcs.dsc_pg_control != NULL)
 			hws->funcs.dsc_pg_control(hws, res_pool->dscs[i]->inst, false);
 
+	/* Enables outbox notifications for usb4 dpia */
+	if (dc->res_pool->usb4_dpia_count)
+		dmub_enable_outbox_notification(dc->ctx->dmub_srv);
+
 	/* we want to turn off all dp displays before doing detection */
-	if (dc->config.power_down_display_on_boot) {
-		uint8_t dpcd_power_state = '\0';
-		enum dc_status status = DC_ERROR_UNEXPECTED;
+	if (dc->config.power_down_display_on_boot)
+		dc_link_blank_all_dp_displays(dc);
 
-		for (i = 0; i < dc->link_count; i++) {
-			if (dc->links[i]->connector_signal != SIGNAL_TYPE_DISPLAY_PORT)
-				continue;
-
-			/* if any of the displays are lit up turn them off */
-			status = core_link_read_dpcd(dc->links[i], DP_SET_POWER,
-						     &dpcd_power_state, sizeof(dpcd_power_state));
-			if (status == DC_OK && dpcd_power_state == DP_POWER_STATE_D0) {
-				/* blank dp stream before power off receiver*/
-				if (dc->links[i]->link_enc->funcs->get_dig_frontend) {
-					unsigned int fe;
-
-					fe = dc->links[i]->link_enc->funcs->get_dig_frontend(
-										dc->links[i]->link_enc);
-					if (fe == ENGINE_ID_UNKNOWN)
-						continue;
-
-					for (j = 0; j < dc->res_pool->stream_enc_count; j++) {
-						if (fe == dc->res_pool->stream_enc[j]->id) {
-							dc->res_pool->stream_enc[j]->funcs->dp_blank(
-										dc->res_pool->stream_enc[j]);
-							break;
-						}
-					}
-				}
-				dp_receiver_power_ctrl(dc->links[i], false);
-			}
-		}
-	}
+	if (hws->funcs.enable_power_gating_plane)
+		hws->funcs.enable_power_gating_plane(dc->hwseq, true);
 
 	/* If taking control over from VBIOS, we may want to optimize our first
 	 * mode set, so we need to skip powering down pipes until we know which
@@ -247,7 +227,8 @@
 			for (i = 0; i < dc->link_count; i++) {
 				struct dc_link *link = dc->links[i];
 
-				if (link->link_enc->funcs->is_dig_enabled &&
+				if (link->ep_type == DISPLAY_ENDPOINT_PHY &&
+						link->link_enc->funcs->is_dig_enabled &&
 						link->link_enc->funcs->is_dig_enabled(link->link_enc) &&
 						dc->hwss.power_down) {
 					dc->hwss.power_down(dc);
@@ -287,8 +268,6 @@
 
 		REG_UPDATE(DCFCLK_CNTL, DCFCLK_GATE_DIS, 0);
 	}
-	if (hws->funcs.enable_power_gating_plane)
-		hws->funcs.enable_power_gating_plane(dc->hwseq, true);
 
 	if (!dcb->funcs->is_accelerated_mode(dcb) && dc->res_pool->hubbub->funcs->init_watermarks)
 		dc->res_pool->hubbub->funcs->init_watermarks(dc->res_pool->hubbub);
@@ -302,8 +281,10 @@
 	if (dc->res_pool->hubbub->funcs->force_pstate_change_control)
 		dc->res_pool->hubbub->funcs->force_pstate_change_control(
 				dc->res_pool->hubbub, false, false);
+#if defined(CONFIG_DRM_AMD_DC_DCN)
 	if (dc->res_pool->hubbub->funcs->init_crb)
 		dc->res_pool->hubbub->funcs->init_crb(dc->res_pool->hubbub);
+#endif
 }
 
 void dcn31_dsc_pg_control(
@@ -593,6 +574,9 @@
 				old_clk->funcs->cs_power_down(old_clk);
 		}
 	}
+
+	/* New dc_state in the process of being applied to hardware. */
+	dc->current_state->res_ctx.link_enc_cfg_ctx.mode = LINK_ENC_CFG_TRANSIENT;
 }
 
 bool dcn31_is_abm_supported(struct dc *dc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_init.c
@@ -100,6 +100,8 @@
 	.z10_save_init = dcn31_z10_save_init,
 	.is_abm_supported = dcn31_is_abm_supported,
 	.set_disp_pattern_generator = dcn30_set_disp_pattern_generator,
+	.optimize_pwr_state = dcn21_optimize_pwr_state,
+	.exit_optimized_pwr_state = dcn21_exit_optimized_pwr_state,
 	.update_visual_confirm_color = dcn20_update_visual_confirm_color,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c
@@ -352,6 +352,14 @@
 	clk_src_regs(3, D),
 	clk_src_regs(4, E)
 };
+/*pll_id being rempped in dmub, in driver it is logical instance*/
+static const struct dce110_clk_src_regs clk_src_regs_b0[] = {
+	clk_src_regs(0, A),
+	clk_src_regs(1, B),
+	clk_src_regs(2, F),
+	clk_src_regs(3, G),
+	clk_src_regs(4, E)
+};
 
 static const struct dce110_clk_src_shift cs_shift = {
 		CS_COMMON_MASK_SH_LIST_DCN2_0(__SHIFT)
@@ -462,7 +470,8 @@
 	SE_DCN3_REG_LIST(id)\
 }
 
-static const struct dcn10_stream_enc_registers stream_enc_regs[] = {
+/* Some encoders won't be initialized here - but they're logical, not physical. */
+static const struct dcn10_stream_enc_registers stream_enc_regs[ENGINE_ID_COUNT] = {
 	stream_enc_regs(0),
 	stream_enc_regs(1),
 	stream_enc_regs(2),
@@ -923,7 +932,7 @@
 	.timing_trace = false,
 	.clock_trace = true,
 	.disable_pplib_clock_request = false,
-	.pipe_split_policy = MPC_SPLIT_AVOID,
+	.pipe_split_policy = MPC_SPLIT_DYNAMIC,
 	.force_single_disp_pipe_split = false,
 	.disable_dcc = DCC_ENABLE,
 	.vsr_support = true,
@@ -931,7 +940,7 @@
 	.max_downscale_src_width = 4096,/*upto true 4K*/
 	.disable_pplib_wm_range = false,
 	.scl_reset_length10 = true,
-	.sanity_checks = false,
+	.sanity_checks = true,
 	.underflow_assert_delay_us = 0xFFFFFFFF,
 	.dwb_fi_phase = -1, // -1 = disable,
 	.dmub_command_table = true,
@@ -948,6 +957,7 @@
 			.optc = false,
 		}
 	},
+	.disable_z10 = true,
 	.optimize_edp_link_rate = true,
 	.enable_sw_cntl_psr = true,
 };
@@ -1281,13 +1291,11 @@
 	vpg = dcn31_vpg_create(ctx, vpg_inst);
 	afmt = dcn31_afmt_create(ctx, afmt_inst);
 
-	if (!enc1 || !vpg || !afmt)
+	if (!enc1 || !vpg || !afmt) {
+		kfree(enc1);
+		kfree(vpg);
+		kfree(afmt);
 		return NULL;
-
-	if (ctx->asic_id.chip_family == FAMILY_YELLOW_CARP &&
-			ctx->asic_id.hw_internal_rev == YELLOW_CARP_B0) {
-		if ((eng_id == ENGINE_ID_DIGC) || (eng_id == ENGINE_ID_DIGD))
-			eng_id = eng_id + 3; // For B0 only. C->F, D->G.
 	}
 
 	dcn30_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios,
@@ -1660,6 +1668,15 @@
 	if (context->bw_ctx.dml.soc.min_dcfclk > dcfclk)
 		dcfclk = context->bw_ctx.dml.soc.min_dcfclk;
 
+	/* We don't recalculate clocks for 0 pipe configs, which can block
+	 * S0i3 as high clocks will block low power states
+	 * Override any clocks that can block S0i3 to min here
+	 */
+	if (pipe_cnt == 0) {
+		context->bw_ctx.bw.dcn.clk.dcfclk_khz = dcfclk; // always should be vlevel 0
+		return;
+	}
+
 	pipes[0].clks_cfg.voltage = vlevel;
 	pipes[0].clks_cfg.dcfclk_mhz = dcfclk;
 	pipes[0].clks_cfg.socclk_mhz = context->bw_ctx.dml.soc.clock_limits[vlevel].socclk_mhz;
@@ -1785,6 +1802,60 @@
 	DC_FP_END();
 }
 
+bool dcn31_validate_bandwidth(struct dc *dc,
+		struct dc_state *context,
+		bool fast_validate)
+{
+	bool out = false;
+
+	BW_VAL_TRACE_SETUP();
+
+	int vlevel = 0;
+	int pipe_cnt = 0;
+	display_e2e_pipe_params_st *pipes = kzalloc(dc->res_pool->pipe_count * sizeof(display_e2e_pipe_params_st), GFP_KERNEL);
+	DC_LOGGER_INIT(dc->ctx->logger);
+
+	BW_VAL_TRACE_COUNT();
+
+	DC_FP_START();
+	out = dcn30_internal_validate_bw(dc, context, pipes, &pipe_cnt, &vlevel, fast_validate);
+	DC_FP_END();
+
+	// Disable fast_validate to set min dcfclk in alculate_wm_and_dlg
+	if (pipe_cnt == 0)
+		fast_validate = false;
+
+	if (!out)
+		goto validate_fail;
+
+	BW_VAL_TRACE_END_VOLTAGE_LEVEL();
+
+	if (fast_validate) {
+		BW_VAL_TRACE_SKIP(fast);
+		goto validate_out;
+	}
+
+	dc->res_pool->funcs->calculate_wm_and_dlg(dc, context, pipes, pipe_cnt, vlevel);
+
+	BW_VAL_TRACE_END_WATERMARKS();
+
+	goto validate_out;
+
+validate_fail:
+	DC_LOG_WARNING("Mode Validation Warning: %s failed alidation.\n",
+		dml_get_status_message(context->bw_ctx.dml.vba.ValidationStatus[context->bw_ctx.dml.vba.soc.num_states]));
+
+	BW_VAL_TRACE_SKIP(fail);
+	out = false;
+
+validate_out:
+	kfree(pipes);
+
+	BW_VAL_TRACE_FINISH();
+
+	return out;
+}
+
 static struct dc_cap_funcs cap_funcs = {
 	.get_dcc_compression_cap = dcn20_get_dcc_compression_cap
 };
@@ -1867,7 +1938,7 @@
 	.link_encs_assign = link_enc_cfg_link_encs_assign,
 	.link_enc_unassign = link_enc_cfg_link_enc_unassign,
 	.panel_cntl_create = dcn31_panel_cntl_create,
-	.validate_bandwidth = dcn30_validate_bandwidth,
+	.validate_bandwidth = dcn31_validate_bandwidth,
 	.calculate_wm_and_dlg = dcn31_calculate_wm_and_dlg,
 	.update_soc_for_wm_a = dcn31_update_soc_for_wm_a,
 	.populate_dml_pipes = dcn31_populate_dml_pipes_from_context,
@@ -2019,14 +2090,27 @@
 			dcn30_clock_source_create(ctx, ctx->dc_bios,
 				CLOCK_SOURCE_COMBO_PHY_PLL1,
 				&clk_src_regs[1], false);
-	pool->base.clock_sources[DCN31_CLK_SRC_PLL2] =
+	/*move phypllx_pixclk_resync to dmub next*/
+	if (dc->ctx->asic_id.hw_internal_rev == YELLOW_CARP_B0) {
+		pool->base.clock_sources[DCN31_CLK_SRC_PLL2] =
+			dcn30_clock_source_create(ctx, ctx->dc_bios,
+				CLOCK_SOURCE_COMBO_PHY_PLL2,
+				&clk_src_regs_b0[2], false);
+		pool->base.clock_sources[DCN31_CLK_SRC_PLL3] =
+			dcn30_clock_source_create(ctx, ctx->dc_bios,
+				CLOCK_SOURCE_COMBO_PHY_PLL3,
+				&clk_src_regs_b0[3], false);
+	} else {
+		pool->base.clock_sources[DCN31_CLK_SRC_PLL2] =
 			dcn30_clock_source_create(ctx, ctx->dc_bios,
 				CLOCK_SOURCE_COMBO_PHY_PLL2,
 				&clk_src_regs[2], false);
-	pool->base.clock_sources[DCN31_CLK_SRC_PLL3] =
+		pool->base.clock_sources[DCN31_CLK_SRC_PLL3] =
 			dcn30_clock_source_create(ctx, ctx->dc_bios,
 				CLOCK_SOURCE_COMBO_PHY_PLL3,
 				&clk_src_regs[3], false);
+	}
+
 	pool->base.clock_sources[DCN31_CLK_SRC_PLL4] =
 			dcn30_clock_source_create(ctx, ctx->dc_bios,
 				CLOCK_SOURCE_COMBO_PHY_PLL4,
@@ -2180,6 +2264,13 @@
 		pool->base.sw_i2cs[i] = NULL;
 	}
 
+	if (dc->ctx->asic_id.chip_family == FAMILY_YELLOW_CARP &&
+	    dc->ctx->asic_id.hw_internal_rev == YELLOW_CARP_B0 &&
+	    !dc->debug.dpia_debug.bits.disable_dpia) {
+		/* YELLOW CARP B0 has 4 DPIA's */
+		pool->base.usb4_dpia_count = 4;
+	}
+
 	/* Audio, Stream Encoders including HPO and virtual, MPC 3D LUTs */
 	if (!resource_construct(num_virtual_links, dc, &pool->base,
 			(!IS_FPGA_MAXIMUS_DC(dc->ctx->dce_environment) ?
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.h
@@ -39,4 +39,35 @@
 		const struct dc_init_data *init_data,
 		struct dc *dc);
 
+/*temp: B0 specific before switch to dcn313 headers*/
+#ifndef regPHYPLLF_PIXCLK_RESYNC_CNTL
+#define regPHYPLLF_PIXCLK_RESYNC_CNTL 0x007e
+#define regPHYPLLF_PIXCLK_RESYNC_CNTL_BASE_IDX 1
+#define regPHYPLLG_PIXCLK_RESYNC_CNTL 0x005f
+#define regPHYPLLG_PIXCLK_RESYNC_CNTL_BASE_IDX 1
+
+//PHYPLLF_PIXCLK_RESYNC_CNTL
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_PIXCLK_RESYNC_ENABLE__SHIFT 0x0
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_DEEP_COLOR_DTO_ENABLE_STATUS__SHIFT 0x1
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_DCCG_DEEP_COLOR_CNTL__SHIFT 0x4
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_PIXCLK_ENABLE__SHIFT 0x8
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_PIXCLK_DOUBLE_RATE_ENABLE__SHIFT 0x9
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_PIXCLK_RESYNC_ENABLE_MASK 0x00000001L
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_DEEP_COLOR_DTO_ENABLE_STATUS_MASK 0x00000002L
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_DCCG_DEEP_COLOR_CNTL_MASK 0x00000030L
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_PIXCLK_ENABLE_MASK 0x00000100L
+#define PHYPLLF_PIXCLK_RESYNC_CNTL__PHYPLLF_PIXCLK_DOUBLE_RATE_ENABLE_MASK 0x00000200L
+
+//PHYPLLG_PIXCLK_RESYNC_CNTL
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_PIXCLK_RESYNC_ENABLE__SHIFT 0x0
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_DEEP_COLOR_DTO_ENABLE_STATUS__SHIFT 0x1
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_DCCG_DEEP_COLOR_CNTL__SHIFT 0x4
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_PIXCLK_ENABLE__SHIFT 0x8
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_PIXCLK_DOUBLE_RATE_ENABLE__SHIFT 0x9
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_PIXCLK_RESYNC_ENABLE_MASK 0x00000001L
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_DEEP_COLOR_DTO_ENABLE_STATUS_MASK 0x00000002L
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_DCCG_DEEP_COLOR_CNTL_MASK 0x00000030L
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_PIXCLK_ENABLE_MASK 0x00000100L
+#define PHYPLLG_PIXCLK_RESYNC_CNTL__PHYPLLG_PIXCLK_DOUBLE_RATE_ENABLE_MASK 0x00000200L
+#endif
 #endif /* _DCN31_RESOURCE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dm_helpers.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dm_helpers.h
@@ -173,4 +173,9 @@
 		const struct dc_link *link,
 		struct aux_payload *payload,
 		enum aux_return_code_type *operation_result);
+enum set_config_status;
+int dm_helpers_dmub_set_config_sync(struct dc_context *ctx,
+		const struct dc_link *link,
+		struct set_config_cmd_payload *payload,
+		enum set_config_status *operation_result);
 #endif /* __DM_HELPERS__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/Makefile
@@ -58,19 +58,21 @@
 
 ifdef CONFIG_DRM_AMD_DC_DCN
 CFLAGS_$(AMDDALPATH)/dc/dml/display_mode_vba.o := $(dml_ccflags)
-CFLAGS_$(AMDDALPATH)/dc/dml/dcn2x/dcn2x.o := $(dml_ccflags)
-CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_mode_vba_20.o := $(dml_ccflags)
-CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_mode_vba_20.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/dcn20_fpu.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_mode_vba_20.o := $(dml_ccflags) $(frame_warn_flag)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_rq_dlg_calc_20.o := $(dml_ccflags)
-CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_mode_vba_20v2.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_mode_vba_20v2.o := $(dml_ccflags) $(frame_warn_flag)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn20/display_rq_dlg_calc_20v2.o := $(dml_ccflags)
-CFLAGS_$(AMDDALPATH)/dc/dml/dcn21/display_mode_vba_21.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/dcn21/display_mode_vba_21.o := $(dml_ccflags) $(frame_warn_flag)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn21/display_rq_dlg_calc_21.o := $(dml_ccflags)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn30/display_mode_vba_30.o := $(dml_ccflags) $(frame_warn_flag)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn30/display_rq_dlg_calc_30.o := $(dml_ccflags)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn31/display_mode_vba_31.o := $(dml_ccflags) $(frame_warn_flag)
 CFLAGS_$(AMDDALPATH)/dc/dml/dcn31/display_rq_dlg_calc_31.o := $(dml_ccflags)
-CFLAGS_$(AMDDALPATH)/dc/dml/display_mode_lib.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/dsc/rc_calc_fpu.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/calcs/dcn_calcs.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/calcs/dcn_calc_auto.o := $(dml_ccflags)
+CFLAGS_$(AMDDALPATH)/dc/dml/calcs/dcn_calc_math.o := $(dml_ccflags) -Wno-tautological-compare
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/display_mode_vba.o := $(dml_rcflags)
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/dcn2x/dcn2x.o := $(dml_rcflags)
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/dcn20/display_mode_vba_20.o := $(dml_rcflags)
@@ -84,21 +86,28 @@
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/dcn31/display_mode_vba_31.o := $(dml_rcflags)
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/dcn31/display_rq_dlg_calc_31.o := $(dml_rcflags)
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/display_mode_lib.o := $(dml_rcflags)
+CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/dsc/rc_calc_fpu.o  := $(dml_rcflags)
 endif
 CFLAGS_$(AMDDALPATH)/dc/dml/dml1_display_rq_dlg_calc.o := $(dml_ccflags)
 CFLAGS_$(AMDDALPATH)/dc/dml/display_rq_dlg_helpers.o := $(dml_ccflags)
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/dml1_display_rq_dlg_calc.o := $(dml_rcflags)
 CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/display_rq_dlg_helpers.o := $(dml_rcflags)
+CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/calcs/dcn_calcs.o := $(dml_rcflags)
+CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/calcs/dcn_calc_auto.o := $(dml_rcflags)
+CFLAGS_REMOVE_$(AMDDALPATH)/dc/dml/calcs/dcn_calc_math.o := $(dml_rcflags)
 
-DML = display_mode_lib.o display_rq_dlg_helpers.o dml1_display_rq_dlg_calc.o \
+DML = calcs/dce_calcs.o calcs/custom_float.o calcs/bw_fixed.o
 
 ifdef CONFIG_DRM_AMD_DC_DCN
+DML += display_mode_lib.o display_rq_dlg_helpers.o dml1_display_rq_dlg_calc.o
+DML += dcn20/dcn20_fpu.o
 DML += display_mode_vba.o dcn20/display_rq_dlg_calc_20.o dcn20/display_mode_vba_20.o
-DML += dcn2x/dcn2x.o
 DML += dcn20/display_rq_dlg_calc_20v2.o dcn20/display_mode_vba_20v2.o
 DML += dcn21/display_rq_dlg_calc_21.o dcn21/display_mode_vba_21.o
 DML += dcn30/display_mode_vba_30.o dcn30/display_rq_dlg_calc_30.o
 DML += dcn31/display_mode_vba_31.o dcn31/display_rq_dlg_calc_31.o
+DML += dsc/rc_calc_fpu.o
+DML += calcs/dcn_calcs.o calcs/dcn_calc_math.o calcs/dcn_calc_auto.o
 endif
 
 AMD_DAL_DML = $(addprefix $(AMDDALPATH)/dc/dml/,$(DML))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/bw_fixed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/bw_fixed.c
@@ -0,0 +1,191 @@
+/*
+ * Copyright 2015 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+#include "dm_services.h"
+#include "bw_fixed.h"
+
+
+#define MAX_I64 \
+	(int64_t)((1ULL << 63) - 1)
+
+#define MIN_I64 \
+	(-MAX_I64 - 1)
+
+#define FRACTIONAL_PART_MASK \
+	((1ULL << BW_FIXED_BITS_PER_FRACTIONAL_PART) - 1)
+
+#define GET_FRACTIONAL_PART(x) \
+	(FRACTIONAL_PART_MASK & (x))
+
+static uint64_t abs_i64(int64_t arg)
+{
+	if (arg >= 0)
+		return (uint64_t)(arg);
+	else
+		return (uint64_t)(-arg);
+}
+
+struct bw_fixed bw_int_to_fixed_nonconst(int64_t value)
+{
+	struct bw_fixed res;
+	ASSERT(value < BW_FIXED_MAX_I32 && value > BW_FIXED_MIN_I32);
+	res.value = value << BW_FIXED_BITS_PER_FRACTIONAL_PART;
+	return res;
+}
+
+struct bw_fixed bw_frc_to_fixed(int64_t numerator, int64_t denominator)
+{
+	struct bw_fixed res;
+	bool arg1_negative = numerator < 0;
+	bool arg2_negative = denominator < 0;
+	uint64_t arg1_value;
+	uint64_t arg2_value;
+	uint64_t remainder;
+
+	/* determine integer part */
+	uint64_t res_value;
+
+	ASSERT(denominator != 0);
+
+	arg1_value = abs_i64(numerator);
+	arg2_value = abs_i64(denominator);
+	res_value = div64_u64_rem(arg1_value, arg2_value, &remainder);
+
+	ASSERT(res_value <= BW_FIXED_MAX_I32);
+
+	/* determine fractional part */
+	{
+		uint32_t i = BW_FIXED_BITS_PER_FRACTIONAL_PART;
+
+		do
+		{
+			remainder <<= 1;
+
+			res_value <<= 1;
+
+			if (remainder >= arg2_value)
+			{
+				res_value |= 1;
+				remainder -= arg2_value;
+			}
+		} while (--i != 0);
+	}
+
+	/* round up LSB */
+	{
+		uint64_t summand = (remainder << 1) >= arg2_value;
+
+		ASSERT(res_value <= MAX_I64 - summand);
+
+		res_value += summand;
+	}
+
+	res.value = (int64_t)(res_value);
+
+	if (arg1_negative ^ arg2_negative)
+		res.value = -res.value;
+	return res;
+}
+
+struct bw_fixed bw_floor2(
+	const struct bw_fixed arg,
+	const struct bw_fixed significance)
+{
+	struct bw_fixed result;
+	int64_t multiplicand;
+
+	multiplicand = div64_s64(arg.value, abs_i64(significance.value));
+	result.value = abs_i64(significance.value) * multiplicand;
+	ASSERT(abs_i64(result.value) <= abs_i64(arg.value));
+	return result;
+}
+
+struct bw_fixed bw_ceil2(
+	const struct bw_fixed arg,
+	const struct bw_fixed significance)
+{
+	struct bw_fixed result;
+	int64_t multiplicand;
+
+	multiplicand = div64_s64(arg.value, abs_i64(significance.value));
+	result.value = abs_i64(significance.value) * multiplicand;
+	if (abs_i64(result.value) < abs_i64(arg.value)) {
+		if (arg.value < 0)
+			result.value -= abs_i64(significance.value);
+		else
+			result.value += abs_i64(significance.value);
+	}
+	return result;
+}
+
+struct bw_fixed bw_mul(const struct bw_fixed arg1, const struct bw_fixed arg2)
+{
+	struct bw_fixed res;
+
+	bool arg1_negative = arg1.value < 0;
+	bool arg2_negative = arg2.value < 0;
+
+	uint64_t arg1_value = abs_i64(arg1.value);
+	uint64_t arg2_value = abs_i64(arg2.value);
+
+	uint64_t arg1_int = BW_FIXED_GET_INTEGER_PART(arg1_value);
+	uint64_t arg2_int = BW_FIXED_GET_INTEGER_PART(arg2_value);
+
+	uint64_t arg1_fra = GET_FRACTIONAL_PART(arg1_value);
+	uint64_t arg2_fra = GET_FRACTIONAL_PART(arg2_value);
+
+	uint64_t tmp;
+
+	res.value = arg1_int * arg2_int;
+
+	ASSERT(res.value <= BW_FIXED_MAX_I32);
+
+	res.value <<= BW_FIXED_BITS_PER_FRACTIONAL_PART;
+
+	tmp = arg1_int * arg2_fra;
+
+	ASSERT(tmp <= (uint64_t)(MAX_I64 - res.value));
+
+	res.value += tmp;
+
+	tmp = arg2_int * arg1_fra;
+
+	ASSERT(tmp <= (uint64_t)(MAX_I64 - res.value));
+
+	res.value += tmp;
+
+	tmp = arg1_fra * arg2_fra;
+
+	tmp = (tmp >> BW_FIXED_BITS_PER_FRACTIONAL_PART) +
+		(tmp >= (uint64_t)(bw_frc_to_fixed(1, 2).value));
+
+	ASSERT(tmp <= (uint64_t)(MAX_I64 - res.value));
+
+	res.value += tmp;
+
+	if (arg1_negative ^ arg2_negative)
+		res.value = -res.value;
+	return res;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/calcs_logger.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/calcs_logger.h
@@ -0,0 +1,578 @@
+/*
+ * Copyright 2018 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#ifndef _CALCS_CALCS_LOGGER_H_
+#define _CALCS_CALCS_LOGGER_H_
+#define DC_LOGGER ctx->logger
+
+static void print_bw_calcs_dceip(struct dc_context *ctx, const struct bw_calcs_dceip *dceip)
+{
+
+	DC_LOG_BANDWIDTH_CALCS("#####################################################################");
+	DC_LOG_BANDWIDTH_CALCS("struct bw_calcs_dceip");
+	DC_LOG_BANDWIDTH_CALCS("#####################################################################");
+	DC_LOG_BANDWIDTH_CALCS("	[enum]   bw_calcs_version version %d", dceip->version);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] large_cursor: %d", dceip->large_cursor);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] dmif_pipe_en_fbc_chunk_tracker: %d", dceip->dmif_pipe_en_fbc_chunk_tracker);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] display_write_back_supported: %d", dceip->display_write_back_supported);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] argb_compression_support: %d", dceip->argb_compression_support);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] pre_downscaler_enabled: %d", dceip->pre_downscaler_enabled);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] underlay_downscale_prefetch_enabled: %d",
+				dceip->underlay_downscale_prefetch_enabled);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] graphics_lb_nodownscaling_multi_line_prefetching: %d",
+				dceip->graphics_lb_nodownscaling_multi_line_prefetching);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] limit_excessive_outstanding_dmif_requests: %d",
+				dceip->limit_excessive_outstanding_dmif_requests);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] cursor_max_outstanding_group_num: %d",
+				dceip->cursor_max_outstanding_group_num);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] lines_interleaved_into_lb: %d", dceip->lines_interleaved_into_lb);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] low_power_tiling_mode: %d", dceip->low_power_tiling_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] chunk_width: %d", dceip->chunk_width);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_graphics_pipes: %d", dceip->number_of_graphics_pipes);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_underlay_pipes: %d", dceip->number_of_underlay_pipes);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] max_dmif_buffer_allocated: %d", dceip->max_dmif_buffer_allocated);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] graphics_dmif_size: %d", dceip->graphics_dmif_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] underlay_luma_dmif_size: %d", dceip->underlay_luma_dmif_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] underlay_chroma_dmif_size: %d", dceip->underlay_chroma_dmif_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] scatter_gather_lines_of_pte_prefetching_in_linear_mode: %d",
+				dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] display_write_back420_luma_mcifwr_buffer_size: %d",
+				dceip->display_write_back420_luma_mcifwr_buffer_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] display_write_back420_chroma_mcifwr_buffer_size: %d",
+				dceip->display_write_back420_chroma_mcifwr_buffer_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] scatter_gather_pte_request_rows_in_tiling_mode: %d",
+				dceip->scatter_gather_pte_request_rows_in_tiling_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay_vscaler_efficiency10_bit_per_component: %d",
+				bw_fixed_to_int(dceip->underlay_vscaler_efficiency10_bit_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay_vscaler_efficiency12_bit_per_component: %d",
+				bw_fixed_to_int(dceip->underlay_vscaler_efficiency12_bit_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] graphics_vscaler_efficiency6_bit_per_component: %d",
+				bw_fixed_to_int(dceip->graphics_vscaler_efficiency6_bit_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] graphics_vscaler_efficiency8_bit_per_component: %d",
+				bw_fixed_to_int(dceip->graphics_vscaler_efficiency8_bit_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] graphics_vscaler_efficiency10_bit_per_component: %d",
+				bw_fixed_to_int(dceip->graphics_vscaler_efficiency10_bit_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] graphics_vscaler_efficiency12_bit_per_component: %d",
+				bw_fixed_to_int(dceip->graphics_vscaler_efficiency12_bit_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] alpha_vscaler_efficiency: %d",
+				bw_fixed_to_int(dceip->alpha_vscaler_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_write_pixels_per_dispclk: %d",
+				bw_fixed_to_int(dceip->lb_write_pixels_per_dispclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_size_per_component444: %d",
+				bw_fixed_to_int(dceip->lb_size_per_component444));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_and_dram_clock_state_change_gated_before_cursor: %d",
+				bw_fixed_to_int(dceip->stutter_and_dram_clock_state_change_gated_before_cursor));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay420_luma_lb_size_per_component: %d",
+				bw_fixed_to_int(dceip->underlay420_luma_lb_size_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay420_chroma_lb_size_per_component: %d",
+				bw_fixed_to_int(dceip->underlay420_chroma_lb_size_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay422_lb_size_per_component: %d",
+				bw_fixed_to_int(dceip->underlay422_lb_size_per_component));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_chunk_width: %d", bw_fixed_to_int(dceip->cursor_chunk_width));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_dcp_buffer_lines: %d",
+				bw_fixed_to_int(dceip->cursor_dcp_buffer_lines));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay_maximum_width_efficient_for_tiling: %d",
+				bw_fixed_to_int(dceip->underlay_maximum_width_efficient_for_tiling));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay_maximum_height_efficient_for_tiling: %d",
+				bw_fixed_to_int(dceip->underlay_maximum_height_efficient_for_tiling));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display: %d",
+				bw_fixed_to_int(dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation: %d",
+				bw_fixed_to_int(dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] minimum_outstanding_pte_request_limit: %d",
+				bw_fixed_to_int(dceip->minimum_outstanding_pte_request_limit));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] maximum_total_outstanding_pte_requests_allowed_by_saw: %d",
+				bw_fixed_to_int(dceip->maximum_total_outstanding_pte_requests_allowed_by_saw));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] linear_mode_line_request_alternation_slice: %d",
+				bw_fixed_to_int(dceip->linear_mode_line_request_alternation_slice));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] request_efficiency: %d", bw_fixed_to_int(dceip->request_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_per_request: %d", bw_fixed_to_int(dceip->dispclk_per_request));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_ramping_factor: %d",
+				bw_fixed_to_int(dceip->dispclk_ramping_factor));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_pipe_throughput_factor: %d",
+				bw_fixed_to_int(dceip->display_pipe_throughput_factor));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwr_all_surfaces_burst_time: %d",
+				bw_fixed_to_int(dceip->mcifwr_all_surfaces_burst_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_request_buffer_size: %d",
+				bw_fixed_to_int(dceip->dmif_request_buffer_size));
+
+
+}
+
+static void print_bw_calcs_vbios(struct dc_context *ctx, const struct bw_calcs_vbios *vbios)
+{
+
+	DC_LOG_BANDWIDTH_CALCS("#####################################################################");
+	DC_LOG_BANDWIDTH_CALCS("struct bw_calcs_vbios vbios");
+	DC_LOG_BANDWIDTH_CALCS("#####################################################################");
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines memory_type: %d", vbios->memory_type);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines memory_type: %d", vbios->memory_type);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] dram_channel_width_in_bits: %d", vbios->dram_channel_width_in_bits);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_dram_channels: %d", vbios->number_of_dram_channels);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_dram_banks: %d", vbios->number_of_dram_banks);
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] low_yclk: %d", bw_fixed_to_int(vbios->low_yclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid_yclk: %d", bw_fixed_to_int(vbios->mid_yclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] high_yclk: %d", bw_fixed_to_int(vbios->high_yclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] low_sclk: %d", bw_fixed_to_int(vbios->low_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid1_sclk: %d", bw_fixed_to_int(vbios->mid1_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid2_sclk: %d", bw_fixed_to_int(vbios->mid2_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid3_sclk: %d", bw_fixed_to_int(vbios->mid3_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid4_sclk: %d", bw_fixed_to_int(vbios->mid4_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid5_sclk: %d", bw_fixed_to_int(vbios->mid5_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid6_sclk: %d", bw_fixed_to_int(vbios->mid6_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] high_sclk: %d", bw_fixed_to_int(vbios->high_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] low_voltage_max_dispclk: %d",
+				bw_fixed_to_int(vbios->low_voltage_max_dispclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid_voltage_max_dispclk;: %d",
+				bw_fixed_to_int(vbios->mid_voltage_max_dispclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] high_voltage_max_dispclk;: %d",
+				bw_fixed_to_int(vbios->high_voltage_max_dispclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] low_voltage_max_phyclk: %d",
+				bw_fixed_to_int(vbios->low_voltage_max_phyclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mid_voltage_max_phyclk: %d",
+				bw_fixed_to_int(vbios->mid_voltage_max_phyclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] high_voltage_max_phyclk: %d",
+				bw_fixed_to_int(vbios->high_voltage_max_phyclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] data_return_bus_width: %d", bw_fixed_to_int(vbios->data_return_bus_width));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] trc: %d", bw_fixed_to_int(vbios->trc));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmifmc_urgent_latency: %d", bw_fixed_to_int(vbios->dmifmc_urgent_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_self_refresh_exit_latency: %d",
+				bw_fixed_to_int(vbios->stutter_self_refresh_exit_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_self_refresh_entry_latency: %d",
+				bw_fixed_to_int(vbios->stutter_self_refresh_entry_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] nbp_state_change_latency: %d",
+				bw_fixed_to_int(vbios->nbp_state_change_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwrmc_urgent_latency: %d",
+				bw_fixed_to_int(vbios->mcifwrmc_urgent_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bool] scatter_gather_enable: %d", vbios->scatter_gather_enable);
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] down_spread_percentage: %d",
+				bw_fixed_to_int(vbios->down_spread_percentage));
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] cursor_width: %d", vbios->cursor_width);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] average_compression_rate: %d", vbios->average_compression_rate);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_request_slots_gmc_reserves_for_dmif_per_channel: %d",
+				vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel);
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] blackout_duration: %d", bw_fixed_to_int(vbios->blackout_duration));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] maximum_blackout_recovery_time: %d",
+				bw_fixed_to_int(vbios->maximum_blackout_recovery_time));
+
+
+}
+
+static void print_bw_calcs_data(struct dc_context *ctx, struct bw_calcs_data *data)
+{
+
+	int i, j, k;
+
+	DC_LOG_BANDWIDTH_CALCS("#####################################################################");
+	DC_LOG_BANDWIDTH_CALCS("struct bw_calcs_data data");
+	DC_LOG_BANDWIDTH_CALCS("#####################################################################");
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_displays: %d", data->number_of_displays);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines underlay_surface_type: %d", data->underlay_surface_type);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines panning_and_bezel_adjustment: %d",
+				data->panning_and_bezel_adjustment);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines graphics_tiling_mode: %d", data->graphics_tiling_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] graphics_lb_bpc: %d", data->graphics_lb_bpc);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] underlay_lb_bpc: %d", data->underlay_lb_bpc);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines underlay_tiling_mode: %d", data->underlay_tiling_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines d0_underlay_mode: %d", data->d0_underlay_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] d1_display_write_back_dwb_enable: %d", data->d1_display_write_back_dwb_enable);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines d1_underlay_mode: %d", data->d1_underlay_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] cpup_state_change_enable: %d", data->cpup_state_change_enable);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] cpuc_state_change_enable: %d", data->cpuc_state_change_enable);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] nbp_state_change_enable: %d", data->nbp_state_change_enable);
+	DC_LOG_BANDWIDTH_CALCS("	[bool] stutter_mode_enable: %d", data->stutter_mode_enable);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] y_clk_level: %d", data->y_clk_level);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] sclk_level: %d", data->sclk_level);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_underlay_surfaces: %d", data->number_of_underlay_surfaces);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_dram_wrchannels: %d", data->number_of_dram_wrchannels);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] chunk_request_delay: %d", data->chunk_request_delay);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] number_of_dram_channels: %d", data->number_of_dram_channels);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines underlay_micro_tile_mode: %d", data->underlay_micro_tile_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines graphics_micro_tile_mode: %d", data->graphics_micro_tile_mode);
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] max_phyclk: %d", bw_fixed_to_int(data->max_phyclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dram_efficiency: %d", bw_fixed_to_int(data->dram_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_width_after_surface_type: %d",
+				bw_fixed_to_int(data->src_width_after_surface_type));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_height_after_surface_type: %d",
+				bw_fixed_to_int(data->src_height_after_surface_type));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] hsr_after_surface_type: %d",
+				bw_fixed_to_int(data->hsr_after_surface_type));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] vsr_after_surface_type: %d", bw_fixed_to_int(data->vsr_after_surface_type));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_width_after_rotation: %d",
+				bw_fixed_to_int(data->src_width_after_rotation));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_height_after_rotation: %d",
+				bw_fixed_to_int(data->src_height_after_rotation));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] hsr_after_rotation: %d", bw_fixed_to_int(data->hsr_after_rotation));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] vsr_after_rotation: %d", bw_fixed_to_int(data->vsr_after_rotation));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] source_height_pixels: %d", bw_fixed_to_int(data->source_height_pixels));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] hsr_after_stereo: %d", bw_fixed_to_int(data->hsr_after_stereo));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] vsr_after_stereo: %d", bw_fixed_to_int(data->vsr_after_stereo));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] source_width_in_lb: %d", bw_fixed_to_int(data->source_width_in_lb));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_line_pitch: %d", bw_fixed_to_int(data->lb_line_pitch));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] underlay_maximum_source_efficient_for_tiling: %d",
+				bw_fixed_to_int(data->underlay_maximum_source_efficient_for_tiling));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] num_lines_at_frame_start: %d",
+				bw_fixed_to_int(data->num_lines_at_frame_start));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_dmif_size_in_time: %d", bw_fixed_to_int(data->min_dmif_size_in_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_mcifwr_size_in_time: %d",
+				bw_fixed_to_int(data->min_mcifwr_size_in_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_requests_for_dmif_size: %d",
+				bw_fixed_to_int(data->total_requests_for_dmif_size));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] peak_pte_request_to_eviction_ratio_limiting: %d",
+				bw_fixed_to_int(data->peak_pte_request_to_eviction_ratio_limiting));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] useful_pte_per_pte_request: %d",
+				bw_fixed_to_int(data->useful_pte_per_pte_request));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_pte_request_rows: %d",
+				bw_fixed_to_int(data->scatter_gather_pte_request_rows));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_row_height: %d",
+				bw_fixed_to_int(data->scatter_gather_row_height));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_pte_requests_in_vblank: %d",
+				bw_fixed_to_int(data->scatter_gather_pte_requests_in_vblank));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] inefficient_linear_pitch_in_bytes: %d",
+				bw_fixed_to_int(data->inefficient_linear_pitch_in_bytes));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_total_data: %d", bw_fixed_to_int(data->cursor_total_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_total_request_groups: %d",
+				bw_fixed_to_int(data->cursor_total_request_groups));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_total_pte_requests: %d",
+				bw_fixed_to_int(data->scatter_gather_total_pte_requests));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_total_pte_request_groups: %d",
+				bw_fixed_to_int(data->scatter_gather_total_pte_request_groups));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] tile_width_in_pixels: %d", bw_fixed_to_int(data->tile_width_in_pixels));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_total_number_of_data_request_page_close_open: %d",
+				bw_fixed_to_int(data->dmif_total_number_of_data_request_page_close_open));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwr_total_number_of_data_request_page_close_open: %d",
+				bw_fixed_to_int(data->mcifwr_total_number_of_data_request_page_close_open));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] bytes_per_page_close_open: %d",
+				bw_fixed_to_int(data->bytes_per_page_close_open));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwr_total_page_close_open_time: %d",
+				bw_fixed_to_int(data->mcifwr_total_page_close_open_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_requests_for_adjusted_dmif_size: %d",
+				bw_fixed_to_int(data->total_requests_for_adjusted_dmif_size));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_dmifmc_urgent_trips: %d",
+				bw_fixed_to_int(data->total_dmifmc_urgent_trips));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_dmifmc_urgent_latency: %d",
+				bw_fixed_to_int(data->total_dmifmc_urgent_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_display_reads_required_data: %d",
+				bw_fixed_to_int(data->total_display_reads_required_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_display_reads_required_dram_access_data: %d",
+				bw_fixed_to_int(data->total_display_reads_required_dram_access_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_display_writes_required_data: %d",
+				bw_fixed_to_int(data->total_display_writes_required_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_display_writes_required_dram_access_data: %d",
+				bw_fixed_to_int(data->total_display_writes_required_dram_access_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_reads_required_data: %d",
+				bw_fixed_to_int(data->display_reads_required_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_reads_required_dram_access_data: %d",
+				bw_fixed_to_int(data->display_reads_required_dram_access_data));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_total_page_close_open_time: %d",
+				bw_fixed_to_int(data->dmif_total_page_close_open_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_cursor_memory_interface_buffer_size_in_time: %d",
+				bw_fixed_to_int(data->min_cursor_memory_interface_buffer_size_in_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_read_buffer_size_in_time: %d",
+				bw_fixed_to_int(data->min_read_buffer_size_in_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_reads_time_for_data_transfer: %d",
+				bw_fixed_to_int(data->display_reads_time_for_data_transfer));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_writes_time_for_data_transfer: %d",
+				bw_fixed_to_int(data->display_writes_time_for_data_transfer));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_required_dram_bandwidth: %d",
+				bw_fixed_to_int(data->dmif_required_dram_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwr_required_dram_bandwidth: %d",
+				bw_fixed_to_int(data->mcifwr_required_dram_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] required_dmifmc_urgent_latency_for_page_close_open: %d",
+				bw_fixed_to_int(data->required_dmifmc_urgent_latency_for_page_close_open));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] required_mcifmcwr_urgent_latency: %d",
+				bw_fixed_to_int(data->required_mcifmcwr_urgent_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] required_dram_bandwidth_gbyte_per_second: %d",
+				bw_fixed_to_int(data->required_dram_bandwidth_gbyte_per_second));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dram_bandwidth: %d", bw_fixed_to_int(data->dram_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_required_sclk: %d", bw_fixed_to_int(data->dmif_required_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwr_required_sclk: %d", bw_fixed_to_int(data->mcifwr_required_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] required_sclk: %d", bw_fixed_to_int(data->required_sclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] downspread_factor: %d", bw_fixed_to_int(data->downspread_factor));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_scaler_efficiency: %d", bw_fixed_to_int(data->v_scaler_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scaler_limits_factor: %d", bw_fixed_to_int(data->scaler_limits_factor));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_pipe_pixel_throughput: %d",
+				bw_fixed_to_int(data->display_pipe_pixel_throughput));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_dispclk_required_with_ramping: %d",
+				bw_fixed_to_int(data->total_dispclk_required_with_ramping));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_dispclk_required_without_ramping: %d",
+				bw_fixed_to_int(data->total_dispclk_required_without_ramping));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_read_request_bandwidth: %d",
+				bw_fixed_to_int(data->total_read_request_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_write_request_bandwidth: %d",
+				bw_fixed_to_int(data->total_write_request_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_required_for_total_read_request_bandwidth: %d",
+				bw_fixed_to_int(data->dispclk_required_for_total_read_request_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_dispclk_required_with_ramping_with_request_bandwidth: %d",
+				bw_fixed_to_int(data->total_dispclk_required_with_ramping_with_request_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_dispclk_required_without_ramping_with_request_bandwidth: %d",
+				bw_fixed_to_int(data->total_dispclk_required_without_ramping_with_request_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk: %d", bw_fixed_to_int(data->dispclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] blackout_recovery_time: %d", bw_fixed_to_int(data->blackout_recovery_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_pixels_per_data_fifo_entry: %d",
+				bw_fixed_to_int(data->min_pixels_per_data_fifo_entry));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] sclk_deep_sleep: %d", bw_fixed_to_int(data->sclk_deep_sleep));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] chunk_request_time: %d", bw_fixed_to_int(data->chunk_request_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_request_time: %d", bw_fixed_to_int(data->cursor_request_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] line_source_pixels_transfer_time: %d",
+				bw_fixed_to_int(data->line_source_pixels_transfer_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmifdram_access_efficiency: %d",
+				bw_fixed_to_int(data->dmifdram_access_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwrdram_access_efficiency: %d",
+				bw_fixed_to_int(data->mcifwrdram_access_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_average_bandwidth_no_compression: %d",
+				bw_fixed_to_int(data->total_average_bandwidth_no_compression));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_average_bandwidth: %d",
+				bw_fixed_to_int(data->total_average_bandwidth));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] total_stutter_cycle_duration: %d",
+				bw_fixed_to_int(data->total_stutter_cycle_duration));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_burst_time: %d", bw_fixed_to_int(data->stutter_burst_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] time_in_self_refresh: %d", bw_fixed_to_int(data->time_in_self_refresh));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_efficiency: %d", bw_fixed_to_int(data->stutter_efficiency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] worst_number_of_trips_to_memory: %d",
+				bw_fixed_to_int(data->worst_number_of_trips_to_memory));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] immediate_flip_time: %d", bw_fixed_to_int(data->immediate_flip_time));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] latency_for_non_dmif_clients: %d",
+				bw_fixed_to_int(data->latency_for_non_dmif_clients));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] latency_for_non_mcifwr_clients: %d",
+				bw_fixed_to_int(data->latency_for_non_mcifwr_clients));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmifmc_urgent_latency_supported_in_high_sclk_and_yclk: %d",
+				bw_fixed_to_int(data->dmifmc_urgent_latency_supported_in_high_sclk_and_yclk));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] nbp_state_dram_speed_change_margin: %d",
+				bw_fixed_to_int(data->nbp_state_dram_speed_change_margin));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_reads_time_for_data_transfer_and_urgent_latency: %d",
+				bw_fixed_to_int(data->display_reads_time_for_data_transfer_and_urgent_latency));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dram_speed_change_margin: %d",
+				bw_fixed_to_int(data->dram_speed_change_margin));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_vblank_dram_speed_change_margin: %d",
+				bw_fixed_to_int(data->min_vblank_dram_speed_change_margin));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_stutter_refresh_duration: %d",
+				bw_fixed_to_int(data->min_stutter_refresh_duration));
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] total_stutter_dmif_buffer_size: %d", data->total_stutter_dmif_buffer_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] total_bytes_requested: %d", data->total_bytes_requested);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] min_stutter_dmif_buffer_size: %d", data->min_stutter_dmif_buffer_size);
+	DC_LOG_BANDWIDTH_CALCS("	[uint32_t] num_stutter_bursts: %d", data->num_stutter_bursts);
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_blank_nbp_state_dram_speed_change_latency_supported: %d",
+				bw_fixed_to_int(data->v_blank_nbp_state_dram_speed_change_latency_supported));
+	DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] nbp_state_dram_speed_change_latency_supported: %d",
+				bw_fixed_to_int(data->nbp_state_dram_speed_change_latency_supported));
+
+	for (i = 0; i < maximum_number_of_surfaces; i++) {
+		DC_LOG_BANDWIDTH_CALCS("	[bool] fbc_en[%d]:%d\n", i, data->fbc_en[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] lpt_en[%d]:%d", i, data->lpt_en[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] displays_match_flag[%d]:%d", i, data->displays_match_flag[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] use_alpha[%d]:%d", i, data->use_alpha[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] orthogonal_rotation[%d]:%d", i, data->orthogonal_rotation[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] enable[%d]:%d", i, data->enable[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] access_one_channel_only[%d]:%d", i, data->access_one_channel_only[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] scatter_gather_enable_for_pipe[%d]:%d",
+					i, data->scatter_gather_enable_for_pipe[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] interlace_mode[%d]:%d",
+					i, data->interlace_mode[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] display_pstate_change_enable[%d]:%d",
+					i, data->display_pstate_change_enable[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bool] line_buffer_prefetch[%d]:%d", i, data->line_buffer_prefetch[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] bytes_per_pixel[%d]:%d", i, data->bytes_per_pixel[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] max_chunks_non_fbc_mode[%d]:%d",
+					i, data->max_chunks_non_fbc_mode[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] lb_bpc[%d]:%d", i, data->lb_bpc[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] output_bpphdmi[%d]:%d", i, data->output_bpphdmi[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] output_bppdp4_lane_hbr[%d]:%d", i, data->output_bppdp4_lane_hbr[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] output_bppdp4_lane_hbr2[%d]:%d",
+					i, data->output_bppdp4_lane_hbr2[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[uint32_t] output_bppdp4_lane_hbr3[%d]:%d",
+					i, data->output_bppdp4_lane_hbr3[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[enum] bw_defines stereo_mode[%d]:%d", i, data->stereo_mode[i]);
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_buffer_transfer_time[%d]:%d",
+					i, bw_fixed_to_int(data->dmif_buffer_transfer_time[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] displays_with_same_mode[%d]:%d",
+					i, bw_fixed_to_int(data->displays_with_same_mode[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_dmif_buffer_size[%d]:%d",
+					i, bw_fixed_to_int(data->stutter_dmif_buffer_size[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_refresh_duration[%d]:%d",
+					i, bw_fixed_to_int(data->stutter_refresh_duration[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_exit_watermark[%d]:%d",
+					i, bw_fixed_to_int(data->stutter_exit_watermark[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_entry_watermark[%d]:%d",
+					i, bw_fixed_to_int(data->stutter_entry_watermark[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] h_total[%d]:%d", i, bw_fixed_to_int(data->h_total[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_total[%d]:%d", i, bw_fixed_to_int(data->v_total[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] pixel_rate[%d]:%d", i, bw_fixed_to_int(data->pixel_rate[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_width[%d]:%d", i, bw_fixed_to_int(data->src_width[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] pitch_in_pixels[%d]:%d",
+					i, bw_fixed_to_int(data->pitch_in_pixels[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] pitch_in_pixels_after_surface_type[%d]:%d",
+					i, bw_fixed_to_int(data->pitch_in_pixels_after_surface_type[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_height[%d]:%d", i, bw_fixed_to_int(data->src_height[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scale_ratio[%d]:%d", i, bw_fixed_to_int(data->scale_ratio[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] h_taps[%d]:%d", i, bw_fixed_to_int(data->h_taps[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_taps[%d]:%d", i, bw_fixed_to_int(data->v_taps[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] h_scale_ratio[%d]:%d", i, bw_fixed_to_int(data->h_scale_ratio[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_scale_ratio[%d]:%d", i, bw_fixed_to_int(data->v_scale_ratio[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] rotation_angle[%d]:%d",
+					i, bw_fixed_to_int(data->rotation_angle[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] compression_rate[%d]:%d",
+					i, bw_fixed_to_int(data->compression_rate[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] hsr[%d]:%d", i, bw_fixed_to_int(data->hsr[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] vsr[%d]:%d", i, bw_fixed_to_int(data->vsr[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] source_width_rounded_up_to_chunks[%d]:%d",
+					i, bw_fixed_to_int(data->source_width_rounded_up_to_chunks[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] source_width_pixels[%d]:%d",
+					i, bw_fixed_to_int(data->source_width_pixels[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] source_height_rounded_up_to_chunks[%d]:%d",
+					i, bw_fixed_to_int(data->source_height_rounded_up_to_chunks[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] display_bandwidth[%d]:%d",
+					i, bw_fixed_to_int(data->display_bandwidth[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] request_bandwidth[%d]:%d",
+					i, bw_fixed_to_int(data->request_bandwidth[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] bytes_per_request[%d]:%d",
+					i, bw_fixed_to_int(data->bytes_per_request[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] useful_bytes_per_request[%d]:%d",
+					i, bw_fixed_to_int(data->useful_bytes_per_request[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lines_interleaved_in_mem_access[%d]:%d",
+					i, bw_fixed_to_int(data->lines_interleaved_in_mem_access[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] latency_hiding_lines[%d]:%d",
+					i, bw_fixed_to_int(data->latency_hiding_lines[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_partitions[%d]:%d",
+					i, bw_fixed_to_int(data->lb_partitions[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_partitions_max[%d]:%d",
+					i, bw_fixed_to_int(data->lb_partitions_max[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_required_with_ramping[%d]:%d",
+					i, bw_fixed_to_int(data->dispclk_required_with_ramping[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_required_without_ramping[%d]:%d",
+					i, bw_fixed_to_int(data->dispclk_required_without_ramping[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] data_buffer_size[%d]:%d",
+					i, bw_fixed_to_int(data->data_buffer_size[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] outstanding_chunk_request_limit[%d]:%d",
+					i, bw_fixed_to_int(data->outstanding_chunk_request_limit[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] urgent_watermark[%d]:%d",
+					i, bw_fixed_to_int(data->urgent_watermark[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] nbp_state_change_watermark[%d]:%d",
+					i, bw_fixed_to_int(data->nbp_state_change_watermark[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_filter_init[%d]:%d", i, bw_fixed_to_int(data->v_filter_init[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] stutter_cycle_duration[%d]:%d",
+					i, bw_fixed_to_int(data->stutter_cycle_duration[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] average_bandwidth[%d]:%d",
+					i, bw_fixed_to_int(data->average_bandwidth[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] average_bandwidth_no_compression[%d]:%d",
+					i, bw_fixed_to_int(data->average_bandwidth_no_compression[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_pte_request_limit[%d]:%d",
+					i, bw_fixed_to_int(data->scatter_gather_pte_request_limit[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_size_per_component[%d]:%d",
+					i, bw_fixed_to_int(data->lb_size_per_component[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] memory_chunk_size_in_bytes[%d]:%d",
+					i, bw_fixed_to_int(data->memory_chunk_size_in_bytes[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] pipe_chunk_size_in_bytes[%d]:%d",
+					i, bw_fixed_to_int(data->pipe_chunk_size_in_bytes[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] number_of_trips_to_memory_for_getting_apte_row[%d]:%d",
+					i, bw_fixed_to_int(data->number_of_trips_to_memory_for_getting_apte_row[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] adjusted_data_buffer_size[%d]:%d",
+					i, bw_fixed_to_int(data->adjusted_data_buffer_size[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] adjusted_data_buffer_size_in_memory[%d]:%d",
+					i, bw_fixed_to_int(data->adjusted_data_buffer_size_in_memory[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] pixels_per_data_fifo_entry[%d]:%d",
+					i, bw_fixed_to_int(data->pixels_per_data_fifo_entry[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_pte_requests_in_row[%d]:%d",
+					i, bw_fixed_to_int(data->scatter_gather_pte_requests_in_row[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] pte_request_per_chunk[%d]:%d",
+					i, bw_fixed_to_int(data->pte_request_per_chunk[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_page_width[%d]:%d",
+					i, bw_fixed_to_int(data->scatter_gather_page_width[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] scatter_gather_page_height[%d]:%d",
+					i, bw_fixed_to_int(data->scatter_gather_page_height[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_lines_in_per_line_out_in_beginning_of_frame[%d]:%d",
+					i, bw_fixed_to_int(data->lb_lines_in_per_line_out_in_beginning_of_frame[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] lb_lines_in_per_line_out_in_middle_of_frame[%d]:%d",
+					i, bw_fixed_to_int(data->lb_lines_in_per_line_out_in_middle_of_frame[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_width_pixels[%d]:%d",
+					i, bw_fixed_to_int(data->cursor_width_pixels[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] minimum_latency_hiding[%d]:%d",
+					i, bw_fixed_to_int(data->minimum_latency_hiding[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] maximum_latency_hiding[%d]:%d",
+					i, bw_fixed_to_int(data->maximum_latency_hiding[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] minimum_latency_hiding_with_cursor[%d]:%d",
+					i, bw_fixed_to_int(data->minimum_latency_hiding_with_cursor[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] maximum_latency_hiding_with_cursor[%d]:%d",
+					i, bw_fixed_to_int(data->maximum_latency_hiding_with_cursor[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_pixels_for_first_output_pixel[%d]:%d",
+					i, bw_fixed_to_int(data->src_pixels_for_first_output_pixel[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_pixels_for_last_output_pixel[%d]:%d",
+					i, bw_fixed_to_int(data->src_pixels_for_last_output_pixel[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_data_for_first_output_pixel[%d]:%d",
+					i, bw_fixed_to_int(data->src_data_for_first_output_pixel[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] src_data_for_last_output_pixel[%d]:%d",
+					i, bw_fixed_to_int(data->src_data_for_last_output_pixel[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] active_time[%d]:%d", i, bw_fixed_to_int(data->active_time[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] horizontal_blank_and_chunk_granularity_factor[%d]:%d",
+					i, bw_fixed_to_int(data->horizontal_blank_and_chunk_granularity_factor[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] cursor_latency_hiding[%d]:%d",
+					i, bw_fixed_to_int(data->cursor_latency_hiding[i]));
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] v_blank_dram_speed_change_margin[%d]:%d",
+					i, bw_fixed_to_int(data->v_blank_dram_speed_change_margin[i]));
+		}
+
+	for (i = 0; i < maximum_number_of_surfaces; i++) {
+		for (j = 0; j < 3; j++) {
+			for (k = 0; k < 8; k++) {
+
+				DC_LOG_BANDWIDTH_CALCS("\n	[bw_fixed] line_source_transfer_time[%d][%d][%d]:%d",
+					i, j, k, bw_fixed_to_int(data->line_source_transfer_time[i][j][k]));
+				DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dram_speed_change_line_source_transfer_time[%d][%d][%d]:%d",
+					i, j, k,
+					bw_fixed_to_int(data->dram_speed_change_line_source_transfer_time[i][j][k]));
+			}
+		}
+	}
+
+	for (i = 0; i < 3; i++) {
+		for (j = 0; j < 8; j++) {
+
+			DC_LOG_BANDWIDTH_CALCS("\n	[uint32_t] num_displays_with_margin[%d][%d]:%d",
+					i, j, data->num_displays_with_margin[i][j]);
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_burst_time[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->dmif_burst_time[i][j]));
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] mcifwr_burst_time[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->mcifwr_burst_time[i][j]));
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] min_dram_speed_change_margin[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->min_dram_speed_change_margin[i][j]));
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_required_for_dram_speed_change[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->dispclk_required_for_dram_speed_change[i][j]));
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] blackout_duration_margin[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->blackout_duration_margin[i][j]));
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_required_for_blackout_duration[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->dispclk_required_for_blackout_duration[i][j]));
+			DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dispclk_required_for_blackout_recovery[%d][%d]:%d",
+					i, j, bw_fixed_to_int(data->dispclk_required_for_blackout_recovery[i][j]));
+		}
+	}
+
+	for (i = 0; i < 6; i++) {
+		DC_LOG_BANDWIDTH_CALCS("	[bw_fixed] dmif_required_sclk_for_urgent_latency[%d]:%d",
+					i, bw_fixed_to_int(data->dmif_required_sclk_for_urgent_latency[i]));
+	}
+}
+;
+
+#endif /* _CALCS_CALCS_LOGGER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/custom_float.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/custom_float.c
@@ -0,0 +1,197 @@
+/*
+ * Copyright 2017 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+#include "dm_services.h"
+#include "custom_float.h"
+
+
+static bool build_custom_float(
+	struct fixed31_32 value,
+	const struct custom_float_format *format,
+	bool *negative,
+	uint32_t *mantissa,
+	uint32_t *exponenta)
+{
+	uint32_t exp_offset = (1 << (format->exponenta_bits - 1)) - 1;
+
+	const struct fixed31_32 mantissa_constant_plus_max_fraction =
+		dc_fixpt_from_fraction(
+			(1LL << (format->mantissa_bits + 1)) - 1,
+			1LL << format->mantissa_bits);
+
+	struct fixed31_32 mantiss;
+
+	if (dc_fixpt_eq(
+		value,
+		dc_fixpt_zero)) {
+		*negative = false;
+		*mantissa = 0;
+		*exponenta = 0;
+		return true;
+	}
+
+	if (dc_fixpt_lt(
+		value,
+		dc_fixpt_zero)) {
+		*negative = format->sign;
+		value = dc_fixpt_neg(value);
+	} else {
+		*negative = false;
+	}
+
+	if (dc_fixpt_lt(
+		value,
+		dc_fixpt_one)) {
+		uint32_t i = 1;
+
+		do {
+			value = dc_fixpt_shl(value, 1);
+			++i;
+		} while (dc_fixpt_lt(
+			value,
+			dc_fixpt_one));
+
+		--i;
+
+		if (exp_offset <= i) {
+			*mantissa = 0;
+			*exponenta = 0;
+			return true;
+		}
+
+		*exponenta = exp_offset - i;
+	} else if (dc_fixpt_le(
+		mantissa_constant_plus_max_fraction,
+		value)) {
+		uint32_t i = 1;
+
+		do {
+			value = dc_fixpt_shr(value, 1);
+			++i;
+		} while (dc_fixpt_lt(
+			mantissa_constant_plus_max_fraction,
+			value));
+
+		*exponenta = exp_offset + i - 1;
+	} else {
+		*exponenta = exp_offset;
+	}
+
+	mantiss = dc_fixpt_sub(
+		value,
+		dc_fixpt_one);
+
+	if (dc_fixpt_lt(
+			mantiss,
+			dc_fixpt_zero) ||
+		dc_fixpt_lt(
+			dc_fixpt_one,
+			mantiss))
+		mantiss = dc_fixpt_zero;
+	else
+		mantiss = dc_fixpt_shl(
+			mantiss,
+			format->mantissa_bits);
+
+	*mantissa = dc_fixpt_floor(mantiss);
+
+	return true;
+}
+
+static bool setup_custom_float(
+	const struct custom_float_format *format,
+	bool negative,
+	uint32_t mantissa,
+	uint32_t exponenta,
+	uint32_t *result)
+{
+	uint32_t i = 0;
+	uint32_t j = 0;
+
+	uint32_t value = 0;
+
+	/* verification code:
+	 * once calculation is ok we can remove it
+	 */
+
+	const uint32_t mantissa_mask =
+		(1 << (format->mantissa_bits + 1)) - 1;
+
+	const uint32_t exponenta_mask =
+		(1 << (format->exponenta_bits + 1)) - 1;
+
+	if (mantissa & ~mantissa_mask) {
+		BREAK_TO_DEBUGGER();
+		mantissa = mantissa_mask;
+	}
+
+	if (exponenta & ~exponenta_mask) {
+		BREAK_TO_DEBUGGER();
+		exponenta = exponenta_mask;
+	}
+
+	/* end of verification code */
+
+	while (i < format->mantissa_bits) {
+		uint32_t mask = 1 << i;
+
+		if (mantissa & mask)
+			value |= mask;
+
+		++i;
+	}
+
+	while (j < format->exponenta_bits) {
+		uint32_t mask = 1 << j;
+
+		if (exponenta & mask)
+			value |= mask << i;
+
+		++j;
+	}
+
+	if (negative && format->sign)
+		value |= 1 << (i + j);
+
+	*result = value;
+
+	return true;
+}
+
+bool convert_to_custom_float_format(
+	struct fixed31_32 value,
+	const struct custom_float_format *format,
+	uint32_t *result)
+{
+	uint32_t mantissa;
+	uint32_t exponenta;
+	bool negative;
+
+	return build_custom_float(
+		value, format, &negative, &mantissa, &exponenta) &&
+	setup_custom_float(
+		format, negative, mantissa, exponenta, result);
+}
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/dce_calcs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/dce_calcs.c
@@ -0,0 +1,3625 @@
+/*
+ * Copyright 2015 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include <linux/slab.h>
+
+#include "resource.h"
+#include "dm_services.h"
+#include "dce_calcs.h"
+#include "dc.h"
+#include "core_types.h"
+#include "dal_asic_id.h"
+#include "calcs_logger.h"
+
+/*
+ * NOTE:
+ *   This file is gcc-parseable HW gospel, coming straight from HW engineers.
+ *
+ * It doesn't adhere to Linux kernel style and sometimes will do things in odd
+ * ways. Unless there is something clearly wrong with it the code should
+ * remain as-is as it provides us with a guarantee from HW that it is correct.
+ */
+
+/*******************************************************************************
+ * Private Functions
+ ******************************************************************************/
+
+static enum bw_calcs_version bw_calcs_version_from_asic_id(struct hw_asic_id asic_id)
+{
+	switch (asic_id.chip_family) {
+
+	case FAMILY_CZ:
+		if (ASIC_REV_IS_STONEY(asic_id.hw_internal_rev))
+			return BW_CALCS_VERSION_STONEY;
+		return BW_CALCS_VERSION_CARRIZO;
+
+	case FAMILY_VI:
+		if (ASIC_REV_IS_POLARIS12_V(asic_id.hw_internal_rev))
+			return BW_CALCS_VERSION_POLARIS12;
+		if (ASIC_REV_IS_POLARIS10_P(asic_id.hw_internal_rev))
+			return BW_CALCS_VERSION_POLARIS10;
+		if (ASIC_REV_IS_POLARIS11_M(asic_id.hw_internal_rev))
+			return BW_CALCS_VERSION_POLARIS11;
+		if (ASIC_REV_IS_VEGAM(asic_id.hw_internal_rev))
+			return BW_CALCS_VERSION_VEGAM;
+		return BW_CALCS_VERSION_INVALID;
+
+	case FAMILY_AI:
+		return BW_CALCS_VERSION_VEGA10;
+
+	default:
+		return BW_CALCS_VERSION_INVALID;
+	}
+}
+
+static void calculate_bandwidth(
+	const struct bw_calcs_dceip *dceip,
+	const struct bw_calcs_vbios *vbios,
+	struct bw_calcs_data *data)
+
+{
+	const int32_t pixels_per_chunk = 512;
+	const int32_t high = 2;
+	const int32_t mid = 1;
+	const int32_t low = 0;
+	const uint32_t s_low = 0;
+	const uint32_t s_mid1 = 1;
+	const uint32_t s_mid2 = 2;
+	const uint32_t s_mid3 = 3;
+	const uint32_t s_mid4 = 4;
+	const uint32_t s_mid5 = 5;
+	const uint32_t s_mid6 = 6;
+	const uint32_t s_high = 7;
+	const uint32_t dmif_chunk_buff_margin = 1;
+
+	uint32_t max_chunks_fbc_mode;
+	int32_t num_cursor_lines;
+
+	int32_t i, j, k;
+	struct bw_fixed *yclk;
+	struct bw_fixed *sclk;
+	bool d0_underlay_enable;
+	bool d1_underlay_enable;
+	bool fbc_enabled;
+	bool lpt_enabled;
+	enum bw_defines sclk_message;
+	enum bw_defines yclk_message;
+	enum bw_defines *tiling_mode;
+	enum bw_defines *surface_type;
+	enum bw_defines voltage;
+	enum bw_defines pipe_check;
+	enum bw_defines hsr_check;
+	enum bw_defines vsr_check;
+	enum bw_defines lb_size_check;
+	enum bw_defines fbc_check;
+	enum bw_defines rotation_check;
+	enum bw_defines mode_check;
+	enum bw_defines nbp_state_change_enable_blank;
+	/*initialize variables*/
+	int32_t number_of_displays_enabled = 0;
+	int32_t number_of_displays_enabled_with_margin = 0;
+	int32_t number_of_aligned_displays_with_no_margin = 0;
+
+	yclk = kcalloc(3, sizeof(*yclk), GFP_KERNEL);
+	if (!yclk)
+		return;
+
+	sclk = kcalloc(8, sizeof(*sclk), GFP_KERNEL);
+	if (!sclk)
+		goto free_yclk;
+
+	tiling_mode = kcalloc(maximum_number_of_surfaces, sizeof(*tiling_mode), GFP_KERNEL);
+	if (!tiling_mode)
+		goto free_sclk;
+
+	surface_type = kcalloc(maximum_number_of_surfaces, sizeof(*surface_type), GFP_KERNEL);
+	if (!surface_type)
+		goto free_tiling_mode;
+
+	yclk[low] = vbios->low_yclk;
+	yclk[mid] = vbios->mid_yclk;
+	yclk[high] = vbios->high_yclk;
+	sclk[s_low] = vbios->low_sclk;
+	sclk[s_mid1] = vbios->mid1_sclk;
+	sclk[s_mid2] = vbios->mid2_sclk;
+	sclk[s_mid3] = vbios->mid3_sclk;
+	sclk[s_mid4] = vbios->mid4_sclk;
+	sclk[s_mid5] = vbios->mid5_sclk;
+	sclk[s_mid6] = vbios->mid6_sclk;
+	sclk[s_high] = vbios->high_sclk;
+	/*''''''''''''''''''*/
+	/* surface assignment:*/
+	/* 0: d0 underlay or underlay luma*/
+	/* 1: d0 underlay chroma*/
+	/* 2: d1 underlay or underlay luma*/
+	/* 3: d1 underlay chroma*/
+	/* 4: d0 graphics*/
+	/* 5: d1 graphics*/
+	/* 6: d2 graphics*/
+	/* 7: d3 graphics, same mode as d2*/
+	/* 8: d4 graphics, same mode as d2*/
+	/* 9: d5 graphics, same mode as d2*/
+	/* ...*/
+	/* maximum_number_of_surfaces-2: d1 display_write_back420 luma*/
+	/* maximum_number_of_surfaces-1: d1 display_write_back420 chroma*/
+	/* underlay luma and chroma surface parameters from spreadsheet*/
+
+
+
+
+	if (data->d0_underlay_mode == bw_def_none)
+		d0_underlay_enable = false;
+	else
+		d0_underlay_enable = true;
+	if (data->d1_underlay_mode == bw_def_none)
+		d1_underlay_enable = false;
+	else
+		d1_underlay_enable = true;
+	data->number_of_underlay_surfaces = d0_underlay_enable + d1_underlay_enable;
+	switch (data->underlay_surface_type) {
+	case bw_def_420:
+		surface_type[0] = bw_def_underlay420_luma;
+		surface_type[2] = bw_def_underlay420_luma;
+		data->bytes_per_pixel[0] = 1;
+		data->bytes_per_pixel[2] = 1;
+		surface_type[1] = bw_def_underlay420_chroma;
+		surface_type[3] = bw_def_underlay420_chroma;
+		data->bytes_per_pixel[1] = 2;
+		data->bytes_per_pixel[3] = 2;
+		data->lb_size_per_component[0] = dceip->underlay420_luma_lb_size_per_component;
+		data->lb_size_per_component[1] = dceip->underlay420_chroma_lb_size_per_component;
+		data->lb_size_per_component[2] = dceip->underlay420_luma_lb_size_per_component;
+		data->lb_size_per_component[3] = dceip->underlay420_chroma_lb_size_per_component;
+		break;
+	case bw_def_422:
+		surface_type[0] = bw_def_underlay422;
+		surface_type[2] = bw_def_underlay422;
+		data->bytes_per_pixel[0] = 2;
+		data->bytes_per_pixel[2] = 2;
+		data->lb_size_per_component[0] = dceip->underlay422_lb_size_per_component;
+		data->lb_size_per_component[2] = dceip->underlay422_lb_size_per_component;
+		break;
+	default:
+		surface_type[0] = bw_def_underlay444;
+		surface_type[2] = bw_def_underlay444;
+		data->bytes_per_pixel[0] = 4;
+		data->bytes_per_pixel[2] = 4;
+		data->lb_size_per_component[0] = dceip->lb_size_per_component444;
+		data->lb_size_per_component[2] = dceip->lb_size_per_component444;
+		break;
+	}
+	if (d0_underlay_enable) {
+		switch (data->underlay_surface_type) {
+		case bw_def_420:
+			data->enable[0] = 1;
+			data->enable[1] = 1;
+			break;
+		default:
+			data->enable[0] = 1;
+			data->enable[1] = 0;
+			break;
+		}
+	}
+	else {
+		data->enable[0] = 0;
+		data->enable[1] = 0;
+	}
+	if (d1_underlay_enable) {
+		switch (data->underlay_surface_type) {
+		case bw_def_420:
+			data->enable[2] = 1;
+			data->enable[3] = 1;
+			break;
+		default:
+			data->enable[2] = 1;
+			data->enable[3] = 0;
+			break;
+		}
+	}
+	else {
+		data->enable[2] = 0;
+		data->enable[3] = 0;
+	}
+	data->use_alpha[0] = 0;
+	data->use_alpha[1] = 0;
+	data->use_alpha[2] = 0;
+	data->use_alpha[3] = 0;
+	data->scatter_gather_enable_for_pipe[0] = vbios->scatter_gather_enable;
+	data->scatter_gather_enable_for_pipe[1] = vbios->scatter_gather_enable;
+	data->scatter_gather_enable_for_pipe[2] = vbios->scatter_gather_enable;
+	data->scatter_gather_enable_for_pipe[3] = vbios->scatter_gather_enable;
+	/*underlay0 same and graphics display pipe0*/
+	data->interlace_mode[0] = data->interlace_mode[4];
+	data->interlace_mode[1] = data->interlace_mode[4];
+	/*underlay1 same and graphics display pipe1*/
+	data->interlace_mode[2] = data->interlace_mode[5];
+	data->interlace_mode[3] = data->interlace_mode[5];
+	/*underlay0 same and graphics display pipe0*/
+	data->h_total[0] = data->h_total[4];
+	data->v_total[0] = data->v_total[4];
+	data->h_total[1] = data->h_total[4];
+	data->v_total[1] = data->v_total[4];
+	/*underlay1 same and graphics display pipe1*/
+	data->h_total[2] = data->h_total[5];
+	data->v_total[2] = data->v_total[5];
+	data->h_total[3] = data->h_total[5];
+	data->v_total[3] = data->v_total[5];
+	/*underlay0 same and graphics display pipe0*/
+	data->pixel_rate[0] = data->pixel_rate[4];
+	data->pixel_rate[1] = data->pixel_rate[4];
+	/*underlay1 same and graphics display pipe1*/
+	data->pixel_rate[2] = data->pixel_rate[5];
+	data->pixel_rate[3] = data->pixel_rate[5];
+	if ((data->underlay_tiling_mode == bw_def_array_linear_general || data->underlay_tiling_mode == bw_def_array_linear_aligned)) {
+		tiling_mode[0] = bw_def_linear;
+		tiling_mode[1] = bw_def_linear;
+		tiling_mode[2] = bw_def_linear;
+		tiling_mode[3] = bw_def_linear;
+	}
+	else {
+		tiling_mode[0] = bw_def_landscape;
+		tiling_mode[1] = bw_def_landscape;
+		tiling_mode[2] = bw_def_landscape;
+		tiling_mode[3] = bw_def_landscape;
+	}
+	data->lb_bpc[0] = data->underlay_lb_bpc;
+	data->lb_bpc[1] = data->underlay_lb_bpc;
+	data->lb_bpc[2] = data->underlay_lb_bpc;
+	data->lb_bpc[3] = data->underlay_lb_bpc;
+	data->compression_rate[0] = bw_int_to_fixed(1);
+	data->compression_rate[1] = bw_int_to_fixed(1);
+	data->compression_rate[2] = bw_int_to_fixed(1);
+	data->compression_rate[3] = bw_int_to_fixed(1);
+	data->access_one_channel_only[0] = 0;
+	data->access_one_channel_only[1] = 0;
+	data->access_one_channel_only[2] = 0;
+	data->access_one_channel_only[3] = 0;
+	data->cursor_width_pixels[0] = bw_int_to_fixed(0);
+	data->cursor_width_pixels[1] = bw_int_to_fixed(0);
+	data->cursor_width_pixels[2] = bw_int_to_fixed(0);
+	data->cursor_width_pixels[3] = bw_int_to_fixed(0);
+	/* graphics surface parameters from spreadsheet*/
+	fbc_enabled = false;
+	lpt_enabled = false;
+	for (i = 4; i <= maximum_number_of_surfaces - 3; i++) {
+		if (i < data->number_of_displays + 4) {
+			if (i == 4 && data->d0_underlay_mode == bw_def_underlay_only) {
+				data->enable[i] = 0;
+				data->use_alpha[i] = 0;
+			}
+			else if (i == 4 && data->d0_underlay_mode == bw_def_blend) {
+				data->enable[i] = 1;
+				data->use_alpha[i] = 1;
+			}
+			else if (i == 4) {
+				data->enable[i] = 1;
+				data->use_alpha[i] = 0;
+			}
+			else if (i == 5 && data->d1_underlay_mode == bw_def_underlay_only) {
+				data->enable[i] = 0;
+				data->use_alpha[i] = 0;
+			}
+			else if (i == 5 && data->d1_underlay_mode == bw_def_blend) {
+				data->enable[i] = 1;
+				data->use_alpha[i] = 1;
+			}
+			else {
+				data->enable[i] = 1;
+				data->use_alpha[i] = 0;
+			}
+		}
+		else {
+			data->enable[i] = 0;
+			data->use_alpha[i] = 0;
+		}
+		data->scatter_gather_enable_for_pipe[i] = vbios->scatter_gather_enable;
+		surface_type[i] = bw_def_graphics;
+		data->lb_size_per_component[i] = dceip->lb_size_per_component444;
+		if (data->graphics_tiling_mode == bw_def_array_linear_general || data->graphics_tiling_mode == bw_def_array_linear_aligned) {
+			tiling_mode[i] = bw_def_linear;
+		}
+		else {
+			tiling_mode[i] = bw_def_tiled;
+		}
+		data->lb_bpc[i] = data->graphics_lb_bpc;
+		if ((data->fbc_en[i] == 1 && (dceip->argb_compression_support || data->d0_underlay_mode != bw_def_blended))) {
+			data->compression_rate[i] = bw_int_to_fixed(vbios->average_compression_rate);
+			data->access_one_channel_only[i] = data->lpt_en[i];
+		}
+		else {
+			data->compression_rate[i] = bw_int_to_fixed(1);
+			data->access_one_channel_only[i] = 0;
+		}
+		if (data->fbc_en[i] == 1) {
+			fbc_enabled = true;
+			if (data->lpt_en[i] == 1) {
+				lpt_enabled = true;
+			}
+		}
+		data->cursor_width_pixels[i] = bw_int_to_fixed(vbios->cursor_width);
+	}
+	/* display_write_back420*/
+	data->scatter_gather_enable_for_pipe[maximum_number_of_surfaces - 2] = 0;
+	data->scatter_gather_enable_for_pipe[maximum_number_of_surfaces - 1] = 0;
+	if (data->d1_display_write_back_dwb_enable == 1) {
+		data->enable[maximum_number_of_surfaces - 2] = 1;
+		data->enable[maximum_number_of_surfaces - 1] = 1;
+	}
+	else {
+		data->enable[maximum_number_of_surfaces - 2] = 0;
+		data->enable[maximum_number_of_surfaces - 1] = 0;
+	}
+	surface_type[maximum_number_of_surfaces - 2] = bw_def_display_write_back420_luma;
+	surface_type[maximum_number_of_surfaces - 1] = bw_def_display_write_back420_chroma;
+	data->lb_size_per_component[maximum_number_of_surfaces - 2] = dceip->underlay420_luma_lb_size_per_component;
+	data->lb_size_per_component[maximum_number_of_surfaces - 1] = dceip->underlay420_chroma_lb_size_per_component;
+	data->bytes_per_pixel[maximum_number_of_surfaces - 2] = 1;
+	data->bytes_per_pixel[maximum_number_of_surfaces - 1] = 2;
+	data->interlace_mode[maximum_number_of_surfaces - 2] = data->interlace_mode[5];
+	data->interlace_mode[maximum_number_of_surfaces - 1] = data->interlace_mode[5];
+	data->h_taps[maximum_number_of_surfaces - 2] = bw_int_to_fixed(1);
+	data->h_taps[maximum_number_of_surfaces - 1] = bw_int_to_fixed(1);
+	data->v_taps[maximum_number_of_surfaces - 2] = bw_int_to_fixed(1);
+	data->v_taps[maximum_number_of_surfaces - 1] = bw_int_to_fixed(1);
+	data->rotation_angle[maximum_number_of_surfaces - 2] = bw_int_to_fixed(0);
+	data->rotation_angle[maximum_number_of_surfaces - 1] = bw_int_to_fixed(0);
+	tiling_mode[maximum_number_of_surfaces - 2] = bw_def_linear;
+	tiling_mode[maximum_number_of_surfaces - 1] = bw_def_linear;
+	data->lb_bpc[maximum_number_of_surfaces - 2] = 8;
+	data->lb_bpc[maximum_number_of_surfaces - 1] = 8;
+	data->compression_rate[maximum_number_of_surfaces - 2] = bw_int_to_fixed(1);
+	data->compression_rate[maximum_number_of_surfaces - 1] = bw_int_to_fixed(1);
+	data->access_one_channel_only[maximum_number_of_surfaces - 2] = 0;
+	data->access_one_channel_only[maximum_number_of_surfaces - 1] = 0;
+	/*assume display pipe1 has dwb enabled*/
+	data->h_total[maximum_number_of_surfaces - 2] = data->h_total[5];
+	data->h_total[maximum_number_of_surfaces - 1] = data->h_total[5];
+	data->v_total[maximum_number_of_surfaces - 2] = data->v_total[5];
+	data->v_total[maximum_number_of_surfaces - 1] = data->v_total[5];
+	data->pixel_rate[maximum_number_of_surfaces - 2] = data->pixel_rate[5];
+	data->pixel_rate[maximum_number_of_surfaces - 1] = data->pixel_rate[5];
+	data->src_width[maximum_number_of_surfaces - 2] = data->src_width[5];
+	data->src_width[maximum_number_of_surfaces - 1] = data->src_width[5];
+	data->src_height[maximum_number_of_surfaces - 2] = data->src_height[5];
+	data->src_height[maximum_number_of_surfaces - 1] = data->src_height[5];
+	data->pitch_in_pixels[maximum_number_of_surfaces - 2] = data->src_width[5];
+	data->pitch_in_pixels[maximum_number_of_surfaces - 1] = data->src_width[5];
+	data->h_scale_ratio[maximum_number_of_surfaces - 2] = bw_int_to_fixed(1);
+	data->h_scale_ratio[maximum_number_of_surfaces - 1] = bw_int_to_fixed(1);
+	data->v_scale_ratio[maximum_number_of_surfaces - 2] = bw_int_to_fixed(1);
+	data->v_scale_ratio[maximum_number_of_surfaces - 1] = bw_int_to_fixed(1);
+	data->stereo_mode[maximum_number_of_surfaces - 2] = bw_def_mono;
+	data->stereo_mode[maximum_number_of_surfaces - 1] = bw_def_mono;
+	data->cursor_width_pixels[maximum_number_of_surfaces - 2] = bw_int_to_fixed(0);
+	data->cursor_width_pixels[maximum_number_of_surfaces - 1] = bw_int_to_fixed(0);
+	data->use_alpha[maximum_number_of_surfaces - 2] = 0;
+	data->use_alpha[maximum_number_of_surfaces - 1] = 0;
+	/*mode check calculations:*/
+	/* mode within dce ip capabilities*/
+	/* fbc*/
+	/* hsr*/
+	/* vsr*/
+	/* lb size*/
+	/*effective scaling source and ratios:*/
+	/*for graphics, non-stereo, non-interlace surfaces when the size of the source and destination are the same, only one tap is used*/
+	/*420 chroma has half the width, height, horizontal and vertical scaling ratios than luma*/
+	/*rotating a graphic or underlay surface swaps the width, height, horizontal and vertical scaling ratios*/
+	/*in top-bottom stereo mode there is 2:1 vertical downscaling for each eye*/
+	/*in side-by-side stereo mode there is 2:1 horizontal downscaling for each eye*/
+	/*in interlace mode there is 2:1 vertical downscaling for each field*/
+	/*in panning or bezel adjustment mode the source width has an extra 128 pixels*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_equ(data->h_scale_ratio[i], bw_int_to_fixed(1)) && bw_equ(data->v_scale_ratio[i], bw_int_to_fixed(1)) && surface_type[i] == bw_def_graphics && data->stereo_mode[i] == bw_def_mono && data->interlace_mode[i] == 0) {
+				data->h_taps[i] = bw_int_to_fixed(1);
+				data->v_taps[i] = bw_int_to_fixed(1);
+			}
+			if (surface_type[i] == bw_def_display_write_back420_chroma || surface_type[i] == bw_def_underlay420_chroma) {
+				data->pitch_in_pixels_after_surface_type[i] = bw_div(data->pitch_in_pixels[i], bw_int_to_fixed(2));
+				data->src_width_after_surface_type = bw_div(data->src_width[i], bw_int_to_fixed(2));
+				data->src_height_after_surface_type = bw_div(data->src_height[i], bw_int_to_fixed(2));
+				data->hsr_after_surface_type = bw_div(data->h_scale_ratio[i], bw_int_to_fixed(2));
+				data->vsr_after_surface_type = bw_div(data->v_scale_ratio[i], bw_int_to_fixed(2));
+			}
+			else {
+				data->pitch_in_pixels_after_surface_type[i] = data->pitch_in_pixels[i];
+				data->src_width_after_surface_type = data->src_width[i];
+				data->src_height_after_surface_type = data->src_height[i];
+				data->hsr_after_surface_type = data->h_scale_ratio[i];
+				data->vsr_after_surface_type = data->v_scale_ratio[i];
+			}
+			if ((bw_equ(data->rotation_angle[i], bw_int_to_fixed(90)) || bw_equ(data->rotation_angle[i], bw_int_to_fixed(270))) && surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				data->src_width_after_rotation = data->src_height_after_surface_type;
+				data->src_height_after_rotation = data->src_width_after_surface_type;
+				data->hsr_after_rotation = data->vsr_after_surface_type;
+				data->vsr_after_rotation = data->hsr_after_surface_type;
+			}
+			else {
+				data->src_width_after_rotation = data->src_width_after_surface_type;
+				data->src_height_after_rotation = data->src_height_after_surface_type;
+				data->hsr_after_rotation = data->hsr_after_surface_type;
+				data->vsr_after_rotation = data->vsr_after_surface_type;
+			}
+			switch (data->stereo_mode[i]) {
+			case bw_def_top_bottom:
+				data->source_width_pixels[i] = data->src_width_after_rotation;
+				data->source_height_pixels = bw_mul(bw_int_to_fixed(2), data->src_height_after_rotation);
+				data->hsr_after_stereo = data->hsr_after_rotation;
+				data->vsr_after_stereo = bw_mul(bw_int_to_fixed(1), data->vsr_after_rotation);
+				break;
+			case bw_def_side_by_side:
+				data->source_width_pixels[i] = bw_mul(bw_int_to_fixed(2), data->src_width_after_rotation);
+				data->source_height_pixels = data->src_height_after_rotation;
+				data->hsr_after_stereo = bw_mul(bw_int_to_fixed(1), data->hsr_after_rotation);
+				data->vsr_after_stereo = data->vsr_after_rotation;
+				break;
+			default:
+				data->source_width_pixels[i] = data->src_width_after_rotation;
+				data->source_height_pixels = data->src_height_after_rotation;
+				data->hsr_after_stereo = data->hsr_after_rotation;
+				data->vsr_after_stereo = data->vsr_after_rotation;
+				break;
+			}
+			data->hsr[i] = data->hsr_after_stereo;
+			if (data->interlace_mode[i]) {
+				data->vsr[i] = bw_mul(data->vsr_after_stereo, bw_int_to_fixed(2));
+			}
+			else {
+				data->vsr[i] = data->vsr_after_stereo;
+			}
+			if (data->panning_and_bezel_adjustment != bw_def_none) {
+				data->source_width_rounded_up_to_chunks[i] = bw_add(bw_floor2(bw_sub(data->source_width_pixels[i], bw_int_to_fixed(1)), bw_int_to_fixed(128)), bw_int_to_fixed(256));
+			}
+			else {
+				data->source_width_rounded_up_to_chunks[i] = bw_ceil2(data->source_width_pixels[i], bw_int_to_fixed(128));
+			}
+			data->source_height_rounded_up_to_chunks[i] = data->source_height_pixels;
+		}
+	}
+	/*mode support checks:*/
+	/*the number of graphics and underlay pipes is limited by the ip support*/
+	/*maximum horizontal and vertical scale ratio is 4, and should not exceed the number of taps*/
+	/*for downscaling with the pre-downscaler, the horizontal scale ratio must be more than the ceiling of one quarter of the number of taps*/
+	/*the pre-downscaler reduces the line buffer source by the horizontal scale ratio*/
+	/*the number of lines in the line buffer has to exceed the number of vertical taps*/
+	/*the size of the line in the line buffer is the product of the source width and the bits per component, rounded up to a multiple of 48*/
+	/*the size of the line in the line buffer in the case of 10 bit per component is the product of the source width rounded up to multiple of 8 and 30.023438 / 3, rounded up to a multiple of 48*/
+	/*the size of the line in the line buffer in the case of 8 bit per component is the product of the source width rounded up to multiple of 8 and 30.023438 / 3, rounded up to a multiple of 48*/
+	/*frame buffer compression is not supported with stereo mode, rotation, or non- 888 formats*/
+	/*rotation is not supported with linear of stereo modes*/
+	if (dceip->number_of_graphics_pipes >= data->number_of_displays && dceip->number_of_underlay_pipes >= data->number_of_underlay_surfaces && !(dceip->display_write_back_supported == 0 && data->d1_display_write_back_dwb_enable == 1)) {
+		pipe_check = bw_def_ok;
+	}
+	else {
+		pipe_check = bw_def_notok;
+	}
+	hsr_check = bw_def_ok;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_neq(data->hsr[i], bw_int_to_fixed(1))) {
+				if (bw_mtn(data->hsr[i], bw_int_to_fixed(4))) {
+					hsr_check = bw_def_hsr_mtn_4;
+				}
+				else {
+					if (bw_mtn(data->hsr[i], data->h_taps[i])) {
+						hsr_check = bw_def_hsr_mtn_h_taps;
+					}
+					else {
+						if (dceip->pre_downscaler_enabled == 1 && bw_mtn(data->hsr[i], bw_int_to_fixed(1)) && bw_leq(data->hsr[i], bw_ceil2(bw_div(data->h_taps[i], bw_int_to_fixed(4)), bw_int_to_fixed(1)))) {
+							hsr_check = bw_def_ceiling__h_taps_div_4___meq_hsr;
+						}
+					}
+				}
+			}
+		}
+	}
+	vsr_check = bw_def_ok;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_neq(data->vsr[i], bw_int_to_fixed(1))) {
+				if (bw_mtn(data->vsr[i], bw_int_to_fixed(4))) {
+					vsr_check = bw_def_vsr_mtn_4;
+				}
+				else {
+					if (bw_mtn(data->vsr[i], data->v_taps[i])) {
+						vsr_check = bw_def_vsr_mtn_v_taps;
+					}
+				}
+			}
+		}
+	}
+	lb_size_check = bw_def_ok;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if ((dceip->pre_downscaler_enabled && bw_mtn(data->hsr[i], bw_int_to_fixed(1)))) {
+				data->source_width_in_lb = bw_div(data->source_width_pixels[i], data->hsr[i]);
+			}
+			else {
+				data->source_width_in_lb = data->source_width_pixels[i];
+			}
+			switch (data->lb_bpc[i]) {
+			case 8:
+				data->lb_line_pitch = bw_ceil2(bw_mul(bw_div(bw_frc_to_fixed(2401171875ul, 100000000), bw_int_to_fixed(3)), bw_ceil2(data->source_width_in_lb, bw_int_to_fixed(8))), bw_int_to_fixed(48));
+				break;
+			case 10:
+				data->lb_line_pitch = bw_ceil2(bw_mul(bw_div(bw_frc_to_fixed(300234375, 10000000), bw_int_to_fixed(3)), bw_ceil2(data->source_width_in_lb, bw_int_to_fixed(8))), bw_int_to_fixed(48));
+				break;
+			default:
+				data->lb_line_pitch = bw_ceil2(bw_mul(bw_int_to_fixed(data->lb_bpc[i]), data->source_width_in_lb), bw_int_to_fixed(48));
+				break;
+			}
+			data->lb_partitions[i] = bw_floor2(bw_div(data->lb_size_per_component[i], data->lb_line_pitch), bw_int_to_fixed(1));
+			/*clamp the partitions to the maxium number supported by the lb*/
+			if ((surface_type[i] != bw_def_graphics || dceip->graphics_lb_nodownscaling_multi_line_prefetching == 1)) {
+				data->lb_partitions_max[i] = bw_int_to_fixed(10);
+			}
+			else {
+				data->lb_partitions_max[i] = bw_int_to_fixed(7);
+			}
+			data->lb_partitions[i] = bw_min2(data->lb_partitions_max[i], data->lb_partitions[i]);
+			if (bw_mtn(bw_add(data->v_taps[i], bw_int_to_fixed(1)), data->lb_partitions[i])) {
+				lb_size_check = bw_def_notok;
+			}
+		}
+	}
+	fbc_check = bw_def_ok;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i] && data->fbc_en[i] == 1 && (bw_equ(data->rotation_angle[i], bw_int_to_fixed(90)) || bw_equ(data->rotation_angle[i], bw_int_to_fixed(270)) || data->stereo_mode[i] != bw_def_mono || data->bytes_per_pixel[i] != 4)) {
+			fbc_check = bw_def_invalid_rotation_or_bpp_or_stereo;
+		}
+	}
+	rotation_check = bw_def_ok;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if ((bw_equ(data->rotation_angle[i], bw_int_to_fixed(90)) || bw_equ(data->rotation_angle[i], bw_int_to_fixed(270))) && (tiling_mode[i] == bw_def_linear || data->stereo_mode[i] != bw_def_mono)) {
+				rotation_check = bw_def_invalid_linear_or_stereo_mode;
+			}
+		}
+	}
+	if (pipe_check == bw_def_ok && hsr_check == bw_def_ok && vsr_check == bw_def_ok && lb_size_check == bw_def_ok && fbc_check == bw_def_ok && rotation_check == bw_def_ok) {
+		mode_check = bw_def_ok;
+	}
+	else {
+		mode_check = bw_def_notok;
+	}
+	/*number of memory channels for write-back client*/
+	data->number_of_dram_wrchannels = vbios->number_of_dram_channels;
+	data->number_of_dram_channels = vbios->number_of_dram_channels;
+	/*modify number of memory channels if lpt mode is enabled*/
+	/* low power tiling mode register*/
+	/* 0 = use channel 0*/
+	/* 1 = use channel 0 and 1*/
+	/* 2 = use channel 0,1,2,3*/
+	if ((fbc_enabled == 1 && lpt_enabled == 1)) {
+		if (vbios->memory_type == bw_def_hbm)
+			data->dram_efficiency = bw_frc_to_fixed(5, 10);
+		else
+			data->dram_efficiency = bw_int_to_fixed(1);
+
+
+		if (dceip->low_power_tiling_mode == 0) {
+			data->number_of_dram_channels = 1;
+		}
+		else if (dceip->low_power_tiling_mode == 1) {
+			data->number_of_dram_channels = 2;
+		}
+		else if (dceip->low_power_tiling_mode == 2) {
+			data->number_of_dram_channels = 4;
+		}
+		else {
+			data->number_of_dram_channels = 1;
+		}
+	}
+	else {
+		if (vbios->memory_type == bw_def_hbm)
+			data->dram_efficiency = bw_frc_to_fixed(5, 10);
+		else
+			data->dram_efficiency = bw_frc_to_fixed(8, 10);
+	}
+	/*memory request size and latency hiding:*/
+	/*request size is normally 64 byte, 2-line interleaved, with full latency hiding*/
+	/*the display write-back requests are single line*/
+	/*for tiled graphics surfaces, or undelay surfaces with width higher than the maximum size for full efficiency, request size is 32 byte in 8 and 16 bpp or if the rotation is orthogonal to the tiling grain. only half is useful of the bytes in the request size in 8 bpp or in 32 bpp if the rotation is orthogonal to the tiling grain.*/
+	/*for undelay surfaces with width lower than the maximum size for full efficiency, requests are 4-line interleaved in 16bpp if the rotation is parallel to the tiling grain, and 8-line interleaved with 4-line latency hiding in 8bpp or if the rotation is orthogonal to the tiling grain.*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if ((bw_equ(data->rotation_angle[i], bw_int_to_fixed(90)) || bw_equ(data->rotation_angle[i], bw_int_to_fixed(270)))) {
+				if ((i < 4)) {
+					/*underlay portrait tiling mode is not supported*/
+					data->orthogonal_rotation[i] = 1;
+				}
+				else {
+					/*graphics portrait tiling mode*/
+					if (data->graphics_micro_tile_mode == bw_def_rotated_micro_tiling) {
+						data->orthogonal_rotation[i] = 0;
+					}
+					else {
+						data->orthogonal_rotation[i] = 1;
+					}
+				}
+			}
+			else {
+				if ((i < 4)) {
+					/*underlay landscape tiling mode is only supported*/
+					if (data->underlay_micro_tile_mode == bw_def_display_micro_tiling) {
+						data->orthogonal_rotation[i] = 0;
+					}
+					else {
+						data->orthogonal_rotation[i] = 1;
+					}
+				}
+				else {
+					/*graphics landscape tiling mode*/
+					if (data->graphics_micro_tile_mode == bw_def_display_micro_tiling) {
+						data->orthogonal_rotation[i] = 0;
+					}
+					else {
+						data->orthogonal_rotation[i] = 1;
+					}
+				}
+			}
+			if (bw_equ(data->rotation_angle[i], bw_int_to_fixed(90)) || bw_equ(data->rotation_angle[i], bw_int_to_fixed(270))) {
+				data->underlay_maximum_source_efficient_for_tiling = dceip->underlay_maximum_height_efficient_for_tiling;
+			}
+			else {
+				data->underlay_maximum_source_efficient_for_tiling = dceip->underlay_maximum_width_efficient_for_tiling;
+			}
+			if (surface_type[i] == bw_def_display_write_back420_luma || surface_type[i] == bw_def_display_write_back420_chroma) {
+				data->bytes_per_request[i] = bw_int_to_fixed(64);
+				data->useful_bytes_per_request[i] = bw_int_to_fixed(64);
+				data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(1);
+				data->latency_hiding_lines[i] = bw_int_to_fixed(1);
+			}
+			else if (tiling_mode[i] == bw_def_linear) {
+				data->bytes_per_request[i] = bw_int_to_fixed(64);
+				data->useful_bytes_per_request[i] = bw_int_to_fixed(64);
+				data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+				data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+			}
+			else {
+				if (surface_type[i] == bw_def_graphics || (bw_mtn(data->source_width_rounded_up_to_chunks[i], bw_ceil2(data->underlay_maximum_source_efficient_for_tiling, bw_int_to_fixed(256))))) {
+					switch (data->bytes_per_pixel[i]) {
+					case 8:
+						data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+						data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+						if (data->orthogonal_rotation[i]) {
+							data->bytes_per_request[i] = bw_int_to_fixed(32);
+							data->useful_bytes_per_request[i] = bw_int_to_fixed(32);
+						}
+						else {
+							data->bytes_per_request[i] = bw_int_to_fixed(64);
+							data->useful_bytes_per_request[i] = bw_int_to_fixed(64);
+						}
+						break;
+					case 4:
+						if (data->orthogonal_rotation[i]) {
+							data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+							data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+							data->bytes_per_request[i] = bw_int_to_fixed(32);
+							data->useful_bytes_per_request[i] = bw_int_to_fixed(16);
+						}
+						else {
+							data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+							data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+							data->bytes_per_request[i] = bw_int_to_fixed(64);
+							data->useful_bytes_per_request[i] = bw_int_to_fixed(64);
+						}
+						break;
+					case 2:
+						data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+						data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+						data->bytes_per_request[i] = bw_int_to_fixed(32);
+						data->useful_bytes_per_request[i] = bw_int_to_fixed(32);
+						break;
+					default:
+						data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+						data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+						data->bytes_per_request[i] = bw_int_to_fixed(32);
+						data->useful_bytes_per_request[i] = bw_int_to_fixed(16);
+						break;
+					}
+				}
+				else {
+					data->bytes_per_request[i] = bw_int_to_fixed(64);
+					data->useful_bytes_per_request[i] = bw_int_to_fixed(64);
+					if (data->orthogonal_rotation[i]) {
+						data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(8);
+						data->latency_hiding_lines[i] = bw_int_to_fixed(4);
+					}
+					else {
+						switch (data->bytes_per_pixel[i]) {
+						case 4:
+							data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(2);
+							data->latency_hiding_lines[i] = bw_int_to_fixed(2);
+							break;
+						case 2:
+							data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(4);
+							data->latency_hiding_lines[i] = bw_int_to_fixed(4);
+							break;
+						default:
+							data->lines_interleaved_in_mem_access[i] = bw_int_to_fixed(8);
+							data->latency_hiding_lines[i] = bw_int_to_fixed(4);
+							break;
+						}
+					}
+				}
+			}
+		}
+	}
+	/*requested peak bandwidth:*/
+	/*the peak request-per-second bandwidth is the product of the maximum source lines in per line out in the beginning*/
+	/*and in the middle of the frame, the ratio of the source width to the line time, the ratio of line interleaving*/
+	/*in memory to lines of latency hiding, and the ratio of bytes per pixel to useful bytes per request.*/
+	/**/
+	/*if the dmif data buffer size holds more than vta_ps worth of source lines, then only vsr is used.*/
+	/*the peak bandwidth is the peak request-per-second bandwidth times the request size.*/
+	/**/
+	/*the line buffer lines in per line out in the beginning of the frame is the vertical filter initialization value*/
+	/*rounded up to even and divided by the line times for initialization, which is normally three.*/
+	/*the line buffer lines in per line out in the middle of the frame is at least one, or the vertical scale ratio,*/
+	/*rounded up to line pairs if not doing line buffer prefetching.*/
+	/**/
+	/*the non-prefetching rounding up of the vertical scale ratio can also be done up to 1 (for a 0,2 pattern), 4/3 (for a 0,2,2 pattern),*/
+	/*6/4 (for a 0,2,2,2 pattern), or 3 (for a 2,4 pattern).*/
+	/**/
+	/*the scaler vertical filter initialization value is calculated by the hardware as the floor of the average of the*/
+	/*vertical scale ratio and the number of vertical taps increased by one.  add one more for possible odd line*/
+	/*panning/bezel adjustment mode.*/
+	/**/
+	/*for the bottom interlace field an extra 50% of the vertical scale ratio is considered for this calculation.*/
+	/*in top-bottom stereo mode software has to set the filter initialization value manually and explicitly limit it to 4.*/
+	/*furthermore, there is only one line time for initialization.*/
+	/**/
+	/*line buffer prefetching is done when the number of lines in the line buffer exceeds the number of taps plus*/
+	/*the ceiling of the vertical scale ratio.*/
+	/**/
+	/*multi-line buffer prefetching is only done in the graphics pipe when the scaler is disabled or when upscaling and the vsr <= 0.8.'*/
+	/**/
+	/*the horizontal blank and chunk granularity factor is indirectly used indicate the interval of time required to transfer the source pixels.*/
+	/*the denominator of this term represents the total number of destination output pixels required for the input source pixels.*/
+	/*it applies when the lines in per line out is not 2 or 4.  it does not apply when there is a line buffer between the scl and blnd.*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->v_filter_init[i] = bw_floor2(bw_div((bw_add(bw_add(bw_add(bw_int_to_fixed(1), data->v_taps[i]), data->vsr[i]), bw_mul(bw_mul(bw_int_to_fixed(data->interlace_mode[i]), bw_frc_to_fixed(5, 10)), data->vsr[i]))), bw_int_to_fixed(2)), bw_int_to_fixed(1));
+			if (data->panning_and_bezel_adjustment == bw_def_any_lines) {
+				data->v_filter_init[i] = bw_add(data->v_filter_init[i], bw_int_to_fixed(1));
+			}
+			if (data->stereo_mode[i] == bw_def_top_bottom) {
+				data->v_filter_init[i] = bw_min2(data->v_filter_init[i], bw_int_to_fixed(4));
+			}
+			if (data->stereo_mode[i] == bw_def_top_bottom) {
+				data->num_lines_at_frame_start = bw_int_to_fixed(1);
+			}
+			else {
+				data->num_lines_at_frame_start = bw_int_to_fixed(3);
+			}
+			if ((bw_mtn(data->vsr[i], bw_int_to_fixed(1)) && surface_type[i] == bw_def_graphics) || data->panning_and_bezel_adjustment == bw_def_any_lines) {
+				data->line_buffer_prefetch[i] = 0;
+			}
+			else if ((((dceip->underlay_downscale_prefetch_enabled == 1 && surface_type[i] != bw_def_graphics) || surface_type[i] == bw_def_graphics) && (bw_mtn(data->lb_partitions[i], bw_add(data->v_taps[i], bw_ceil2(data->vsr[i], bw_int_to_fixed(1))))))) {
+				data->line_buffer_prefetch[i] = 1;
+			}
+			else {
+				data->line_buffer_prefetch[i] = 0;
+			}
+			data->lb_lines_in_per_line_out_in_beginning_of_frame[i] = bw_div(bw_ceil2(data->v_filter_init[i], bw_int_to_fixed(dceip->lines_interleaved_into_lb)), data->num_lines_at_frame_start);
+			if (data->line_buffer_prefetch[i] == 1) {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_max2(bw_int_to_fixed(1), data->vsr[i]);
+			}
+			else if (bw_leq(data->vsr[i], bw_int_to_fixed(1))) {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_int_to_fixed(1);
+			} else if (bw_leq(data->vsr[i],
+					bw_frc_to_fixed(4, 3))) {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_div(bw_int_to_fixed(4), bw_int_to_fixed(3));
+			} else if (bw_leq(data->vsr[i],
+					bw_frc_to_fixed(6, 4))) {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_div(bw_int_to_fixed(6), bw_int_to_fixed(4));
+			}
+			else if (bw_leq(data->vsr[i], bw_int_to_fixed(2))) {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_int_to_fixed(2);
+			}
+			else if (bw_leq(data->vsr[i], bw_int_to_fixed(3))) {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_int_to_fixed(3);
+			}
+			else {
+				data->lb_lines_in_per_line_out_in_middle_of_frame[i] = bw_int_to_fixed(4);
+			}
+			if (data->line_buffer_prefetch[i] == 1 || bw_equ(data->lb_lines_in_per_line_out_in_middle_of_frame[i], bw_int_to_fixed(2)) || bw_equ(data->lb_lines_in_per_line_out_in_middle_of_frame[i], bw_int_to_fixed(4))) {
+				data->horizontal_blank_and_chunk_granularity_factor[i] = bw_int_to_fixed(1);
+			}
+			else {
+				data->horizontal_blank_and_chunk_granularity_factor[i] = bw_div(data->h_total[i], (bw_div((bw_add(data->h_total[i], bw_div((bw_sub(data->source_width_pixels[i], bw_int_to_fixed(dceip->chunk_width))), data->hsr[i]))), bw_int_to_fixed(2))));
+			}
+			data->request_bandwidth[i] = bw_div(bw_mul(bw_div(bw_mul(bw_div(bw_mul(bw_max2(data->lb_lines_in_per_line_out_in_beginning_of_frame[i], data->lb_lines_in_per_line_out_in_middle_of_frame[i]), data->source_width_rounded_up_to_chunks[i]), (bw_div(data->h_total[i], data->pixel_rate[i]))), bw_int_to_fixed(data->bytes_per_pixel[i])), data->useful_bytes_per_request[i]), data->lines_interleaved_in_mem_access[i]), data->latency_hiding_lines[i]);
+			data->display_bandwidth[i] = bw_mul(data->request_bandwidth[i], data->bytes_per_request[i]);
+		}
+	}
+	/*outstanding chunk request limit*/
+	/*if underlay buffer sharing is enabled, the data buffer size for underlay in 422 or 444 is the sum of the luma and chroma data buffer sizes.*/
+	/*underlay buffer sharing mode is only permitted in orthogonal rotation modes.*/
+	/**/
+	/*if there is only one display enabled, the dmif data buffer size for the graphics surface is increased by concatenating the adjacent buffers.*/
+	/**/
+	/*the memory chunk size in bytes is 1024 for the writeback, and 256 times the memory line interleaving and the bytes per pixel for graphics*/
+	/*and underlay.*/
+	/**/
+	/*the pipe chunk size uses 2 for line interleaving, except for the write back, in which case it is 1.*/
+	/*graphics and underlay data buffer size is adjusted (limited) using the outstanding chunk request limit if there is more than one*/
+	/*display enabled or if the dmif request buffer is not large enough for the total data buffer size.*/
+	/*the outstanding chunk request limit is the ceiling of the adjusted data buffer size divided by the chunk size in bytes*/
+	/*the adjusted data buffer size is the product of the display bandwidth and the minimum effective data buffer size in terms of time,*/
+	/*rounded up to the chunk size in bytes, but should not exceed the original data buffer size*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if ((dceip->dmif_pipe_en_fbc_chunk_tracker + 3 == i && fbc_enabled == 0 && tiling_mode[i] != bw_def_linear)) {
+				data->max_chunks_non_fbc_mode[i] = 128 - dmif_chunk_buff_margin;
+			}
+			else {
+				data->max_chunks_non_fbc_mode[i] = 16 - dmif_chunk_buff_margin;
+			}
+		}
+		if (data->fbc_en[i] == 1) {
+			max_chunks_fbc_mode = 128 - dmif_chunk_buff_margin;
+		}
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			switch (surface_type[i]) {
+			case bw_def_display_write_back420_luma:
+				data->data_buffer_size[i] = bw_int_to_fixed(dceip->display_write_back420_luma_mcifwr_buffer_size);
+				break;
+			case bw_def_display_write_back420_chroma:
+				data->data_buffer_size[i] = bw_int_to_fixed(dceip->display_write_back420_chroma_mcifwr_buffer_size);
+				break;
+			case bw_def_underlay420_luma:
+				data->data_buffer_size[i] = bw_int_to_fixed(dceip->underlay_luma_dmif_size);
+				break;
+			case bw_def_underlay420_chroma:
+				data->data_buffer_size[i] = bw_div(bw_int_to_fixed(dceip->underlay_chroma_dmif_size), bw_int_to_fixed(2));
+				break;
+			case bw_def_underlay422:case bw_def_underlay444:
+				if (data->orthogonal_rotation[i] == 0) {
+					data->data_buffer_size[i] = bw_int_to_fixed(dceip->underlay_luma_dmif_size);
+				}
+				else {
+					data->data_buffer_size[i] = bw_add(bw_int_to_fixed(dceip->underlay_luma_dmif_size), bw_int_to_fixed(dceip->underlay_chroma_dmif_size));
+				}
+				break;
+			default:
+				if (data->fbc_en[i] == 1) {
+					/*data_buffer_size(i) = max_dmif_buffer_allocated * graphics_dmif_size*/
+					if (data->number_of_displays == 1) {
+						data->data_buffer_size[i] = bw_min2(bw_mul(bw_mul(bw_int_to_fixed(max_chunks_fbc_mode), bw_int_to_fixed(pixels_per_chunk)), bw_int_to_fixed(data->bytes_per_pixel[i])), bw_mul(bw_int_to_fixed(dceip->max_dmif_buffer_allocated), bw_int_to_fixed(dceip->graphics_dmif_size)));
+					}
+					else {
+						data->data_buffer_size[i] = bw_min2(bw_mul(bw_mul(bw_int_to_fixed(max_chunks_fbc_mode), bw_int_to_fixed(pixels_per_chunk)), bw_int_to_fixed(data->bytes_per_pixel[i])), bw_int_to_fixed(dceip->graphics_dmif_size));
+					}
+				}
+				else {
+					/*the effective dmif buffer size in non-fbc mode is limited by the 16 entry chunk tracker*/
+					if (data->number_of_displays == 1) {
+						data->data_buffer_size[i] = bw_min2(bw_mul(bw_mul(bw_int_to_fixed(data->max_chunks_non_fbc_mode[i]), bw_int_to_fixed(pixels_per_chunk)), bw_int_to_fixed(data->bytes_per_pixel[i])), bw_mul(bw_int_to_fixed(dceip->max_dmif_buffer_allocated), bw_int_to_fixed(dceip->graphics_dmif_size)));
+					}
+					else {
+						data->data_buffer_size[i] = bw_min2(bw_mul(bw_mul(bw_int_to_fixed(data->max_chunks_non_fbc_mode[i]), bw_int_to_fixed(pixels_per_chunk)), bw_int_to_fixed(data->bytes_per_pixel[i])), bw_int_to_fixed(dceip->graphics_dmif_size));
+					}
+				}
+				break;
+			}
+			if (surface_type[i] == bw_def_display_write_back420_luma || surface_type[i] == bw_def_display_write_back420_chroma) {
+				data->memory_chunk_size_in_bytes[i] = bw_int_to_fixed(1024);
+				data->pipe_chunk_size_in_bytes[i] = bw_int_to_fixed(1024);
+			}
+			else {
+				data->memory_chunk_size_in_bytes[i] = bw_mul(bw_mul(bw_int_to_fixed(dceip->chunk_width), data->lines_interleaved_in_mem_access[i]), bw_int_to_fixed(data->bytes_per_pixel[i]));
+				data->pipe_chunk_size_in_bytes[i] = bw_mul(bw_mul(bw_int_to_fixed(dceip->chunk_width), bw_int_to_fixed(dceip->lines_interleaved_into_lb)), bw_int_to_fixed(data->bytes_per_pixel[i]));
+			}
+		}
+	}
+	data->min_dmif_size_in_time = bw_int_to_fixed(9999);
+	data->min_mcifwr_size_in_time = bw_int_to_fixed(9999);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				if (bw_ltn(bw_div(bw_div(bw_mul(data->data_buffer_size[i], data->bytes_per_request[i]), data->useful_bytes_per_request[i]), data->display_bandwidth[i]), data->min_dmif_size_in_time)) {
+					data->min_dmif_size_in_time = bw_div(bw_div(bw_mul(data->data_buffer_size[i], data->bytes_per_request[i]), data->useful_bytes_per_request[i]), data->display_bandwidth[i]);
+				}
+			}
+			else {
+				if (bw_ltn(bw_div(bw_div(bw_mul(data->data_buffer_size[i], data->bytes_per_request[i]), data->useful_bytes_per_request[i]), data->display_bandwidth[i]), data->min_mcifwr_size_in_time)) {
+					data->min_mcifwr_size_in_time = bw_div(bw_div(bw_mul(data->data_buffer_size[i], data->bytes_per_request[i]), data->useful_bytes_per_request[i]), data->display_bandwidth[i]);
+				}
+			}
+		}
+	}
+	data->total_requests_for_dmif_size = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i] && surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+			data->total_requests_for_dmif_size = bw_add(data->total_requests_for_dmif_size, bw_div(data->data_buffer_size[i], data->useful_bytes_per_request[i]));
+		}
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma && dceip->limit_excessive_outstanding_dmif_requests && (data->number_of_displays > 1 || bw_mtn(data->total_requests_for_dmif_size, dceip->dmif_request_buffer_size))) {
+				data->adjusted_data_buffer_size[i] = bw_min2(data->data_buffer_size[i], bw_ceil2(bw_mul(data->min_dmif_size_in_time, data->display_bandwidth[i]), data->memory_chunk_size_in_bytes[i]));
+			}
+			else {
+				data->adjusted_data_buffer_size[i] = data->data_buffer_size[i];
+			}
+		}
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (data->number_of_displays == 1 && data->number_of_underlay_surfaces == 0) {
+				/*set maximum chunk limit if only one graphic pipe is enabled*/
+				data->outstanding_chunk_request_limit[i] = bw_int_to_fixed(127);
+			}
+			else {
+				data->outstanding_chunk_request_limit[i] = bw_ceil2(bw_div(data->adjusted_data_buffer_size[i], data->pipe_chunk_size_in_bytes[i]), bw_int_to_fixed(1));
+				/*clamp maximum chunk limit in the graphic display pipe*/
+				if (i >= 4) {
+					data->outstanding_chunk_request_limit[i] = bw_max2(bw_int_to_fixed(127), data->outstanding_chunk_request_limit[i]);
+				}
+			}
+		}
+	}
+	/*outstanding pte request limit*/
+	/*in tiling mode with no rotation the sg pte requests are 8 useful pt_es, the sg row height is the page height and the sg page width x height is 64x64 for 8bpp, 64x32 for 16 bpp, 32x32 for 32 bpp*/
+	/*in tiling mode with rotation the sg pte requests are only one useful pte, and the sg row height is also the page height, but the sg page width and height are swapped*/
+	/*in linear mode the pte requests are 8 useful pt_es, the sg page width is 4096 divided by the bytes per pixel, the sg page height is 1, but there is just one row whose height is the lines of pte prefetching*/
+	/*the outstanding pte request limit is obtained by multiplying the outstanding chunk request limit by the peak pte request to eviction limiting ratio, rounding up to integer, multiplying by the pte requests per chunk, and rounding up to integer again*/
+	/*if not using peak pte request to eviction limiting, the outstanding pte request limit is the pte requests in the vblank*/
+	/*the pte requests in the vblank is the product of the number of pte request rows times the number of pte requests in a row*/
+	/*the number of pte requests in a row is the quotient of the source width divided by 256, multiplied by the pte requests per chunk, rounded up to even, multiplied by the scatter-gather row height and divided by the scatter-gather page height*/
+	/*the pte requests per chunk is 256 divided by the scatter-gather page width and the useful pt_es per pte request*/
+	if (data->number_of_displays > 1 || (bw_neq(data->rotation_angle[4], bw_int_to_fixed(0)) && bw_neq(data->rotation_angle[4], bw_int_to_fixed(180)))) {
+		data->peak_pte_request_to_eviction_ratio_limiting = dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display;
+	}
+	else {
+		data->peak_pte_request_to_eviction_ratio_limiting = dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation;
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i] && data->scatter_gather_enable_for_pipe[i] == 1) {
+			if (tiling_mode[i] == bw_def_linear) {
+				data->useful_pte_per_pte_request = bw_int_to_fixed(8);
+				data->scatter_gather_page_width[i] = bw_div(bw_int_to_fixed(4096), bw_int_to_fixed(data->bytes_per_pixel[i]));
+				data->scatter_gather_page_height[i] = bw_int_to_fixed(1);
+				data->scatter_gather_pte_request_rows = bw_int_to_fixed(1);
+				data->scatter_gather_row_height = bw_int_to_fixed(dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode);
+			}
+			else if (bw_equ(data->rotation_angle[i], bw_int_to_fixed(0)) || bw_equ(data->rotation_angle[i], bw_int_to_fixed(180))) {
+				data->useful_pte_per_pte_request = bw_int_to_fixed(8);
+				switch (data->bytes_per_pixel[i]) {
+				case 4:
+					data->scatter_gather_page_width[i] = bw_int_to_fixed(32);
+					data->scatter_gather_page_height[i] = bw_int_to_fixed(32);
+					break;
+				case 2:
+					data->scatter_gather_page_width[i] = bw_int_to_fixed(64);
+					data->scatter_gather_page_height[i] = bw_int_to_fixed(32);
+					break;
+				default:
+					data->scatter_gather_page_width[i] = bw_int_to_fixed(64);
+					data->scatter_gather_page_height[i] = bw_int_to_fixed(64);
+					break;
+				}
+				data->scatter_gather_pte_request_rows = bw_int_to_fixed(dceip->scatter_gather_pte_request_rows_in_tiling_mode);
+				data->scatter_gather_row_height = data->scatter_gather_page_height[i];
+			}
+			else {
+				data->useful_pte_per_pte_request = bw_int_to_fixed(1);
+				switch (data->bytes_per_pixel[i]) {
+				case 4:
+					data->scatter_gather_page_width[i] = bw_int_to_fixed(32);
+					data->scatter_gather_page_height[i] = bw_int_to_fixed(32);
+					break;
+				case 2:
+					data->scatter_gather_page_width[i] = bw_int_to_fixed(32);
+					data->scatter_gather_page_height[i] = bw_int_to_fixed(64);
+					break;
+				default:
+					data->scatter_gather_page_width[i] = bw_int_to_fixed(64);
+					data->scatter_gather_page_height[i] = bw_int_to_fixed(64);
+					break;
+				}
+				data->scatter_gather_pte_request_rows = bw_int_to_fixed(dceip->scatter_gather_pte_request_rows_in_tiling_mode);
+				data->scatter_gather_row_height = data->scatter_gather_page_height[i];
+			}
+			data->pte_request_per_chunk[i] = bw_div(bw_div(bw_int_to_fixed(dceip->chunk_width), data->scatter_gather_page_width[i]), data->useful_pte_per_pte_request);
+			data->scatter_gather_pte_requests_in_row[i] = bw_div(bw_mul(bw_ceil2(bw_mul(bw_div(data->source_width_rounded_up_to_chunks[i], bw_int_to_fixed(dceip->chunk_width)), data->pte_request_per_chunk[i]), bw_int_to_fixed(1)), data->scatter_gather_row_height), data->scatter_gather_page_height[i]);
+			data->scatter_gather_pte_requests_in_vblank = bw_mul(data->scatter_gather_pte_request_rows, data->scatter_gather_pte_requests_in_row[i]);
+			if (bw_equ(data->peak_pte_request_to_eviction_ratio_limiting, bw_int_to_fixed(0))) {
+				data->scatter_gather_pte_request_limit[i] = data->scatter_gather_pte_requests_in_vblank;
+			}
+			else {
+				data->scatter_gather_pte_request_limit[i] = bw_max2(dceip->minimum_outstanding_pte_request_limit, bw_min2(data->scatter_gather_pte_requests_in_vblank, bw_ceil2(bw_mul(bw_mul(bw_div(bw_ceil2(data->adjusted_data_buffer_size[i], data->memory_chunk_size_in_bytes[i]), data->memory_chunk_size_in_bytes[i]), data->pte_request_per_chunk[i]), data->peak_pte_request_to_eviction_ratio_limiting), bw_int_to_fixed(1))));
+			}
+		}
+	}
+	/*pitch padding recommended for efficiency in linear mode*/
+	/*in linear mode graphics or underlay with scatter gather, a pitch that is a multiple of the channel interleave (256 bytes) times the channel-bank rotation is not efficient*/
+	/*if that is the case it is recommended to pad the pitch by at least 256 pixels*/
+	data->inefficient_linear_pitch_in_bytes = bw_mul(bw_mul(bw_int_to_fixed(256), bw_int_to_fixed(vbios->number_of_dram_banks)), bw_int_to_fixed(data->number_of_dram_channels));
+
+	/*pixel transfer time*/
+	/*the dmif and mcifwr yclk(pclk) required is the one that allows the transfer of all pipe's data buffer size in memory in the time for data transfer*/
+	/*for dmif, pte and cursor requests have to be included.*/
+	/*the dram data requirement is doubled when the data request size in bytes is less than the dram channel width times the burst size (8)*/
+	/*the dram data requirement is also multiplied by the number of channels in the case of low power tiling*/
+	/*the page close-open time is determined by trc and the number of page close-opens*/
+	/*in tiled mode graphics or underlay with scatter-gather enabled the bytes per page close-open is the product of the memory line interleave times the maximum of the scatter-gather page width and the product of the tile width (8 pixels) times the number of channels times the number of banks.*/
+	/*in linear mode graphics or underlay with scatter-gather enabled and inefficient pitch, the bytes per page close-open is the line request alternation slice, because different lines are in completely different 4k address bases.*/
+	/*otherwise, the bytes page close-open is the chunk size because that is the arbitration slice.*/
+	/*pte requests are grouped by pte requests per chunk if that is more than 1. each group costs a page close-open time for dmif reads*/
+	/*cursor requests outstanding are limited to a group of two source lines. each group costs a page close-open time for dmif reads*/
+	/*the display reads and writes time for data transfer is the minimum data or cursor buffer size in time minus the mc urgent latency*/
+	/*the mc urgent latency is experienced more than one time if the number of dmif requests in the data buffer exceeds the request buffer size plus the request slots reserved for dmif in the dram channel arbiter queues*/
+	/*the dispclk required is the maximum for all surfaces of the maximum of the source pixels for first output pixel times the throughput factor, divided by the pixels per dispclk, and divided by the minimum latency hiding minus the dram speed/p-state change latency minus the burst time, and the source pixels for last output pixel, times the throughput factor, divided by the pixels per dispclk, and divided by the minimum latency hiding minus the dram speed/p-state change latency minus the burst time, plus the active time.*/
+	/*the data burst time is the maximum of the total page close-open time, total dmif/mcifwr buffer size in memory divided by the dram bandwidth, and the total dmif/mcifwr buffer size in memory divided by the 32 byte sclk data bus bandwidth, each multiplied by its efficiency.*/
+	/*the source line transfer time is the maximum for all surfaces of the maximum of the burst time plus the urgent latency times the floor of the data required divided by the buffer size for the fist pixel, and the burst time plus the urgent latency times the floor of the data required divided by the buffer size for the last pixel plus the active time.*/
+	/*the source pixels for the first output pixel is 512 if the scaler vertical filter initialization value is greater than 2, and it is 4 times the source width if it is greater than 4.*/
+	/*the source pixels for the last output pixel is the source width times the scaler vertical filter initialization value rounded up to even*/
+	/*the source data for these pixels is the number of pixels times the bytes per pixel times the bytes per request divided by the useful bytes per request.*/
+	data->cursor_total_data = bw_int_to_fixed(0);
+	data->cursor_total_request_groups = bw_int_to_fixed(0);
+	data->scatter_gather_total_pte_requests = bw_int_to_fixed(0);
+	data->scatter_gather_total_pte_request_groups = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->cursor_total_data = bw_add(data->cursor_total_data, bw_mul(bw_mul(bw_int_to_fixed(2), data->cursor_width_pixels[i]), bw_int_to_fixed(4)));
+			if (dceip->large_cursor == 1) {
+				data->cursor_total_request_groups = bw_add(data->cursor_total_request_groups, bw_int_to_fixed((dceip->cursor_max_outstanding_group_num + 1)));
+			}
+			else {
+				data->cursor_total_request_groups = bw_add(data->cursor_total_request_groups, bw_ceil2(bw_div(data->cursor_width_pixels[i], dceip->cursor_chunk_width), bw_int_to_fixed(1)));
+			}
+			if (data->scatter_gather_enable_for_pipe[i]) {
+				data->scatter_gather_total_pte_requests = bw_add(data->scatter_gather_total_pte_requests, data->scatter_gather_pte_request_limit[i]);
+				data->scatter_gather_total_pte_request_groups = bw_add(data->scatter_gather_total_pte_request_groups, bw_ceil2(bw_div(data->scatter_gather_pte_request_limit[i], bw_ceil2(data->pte_request_per_chunk[i], bw_int_to_fixed(1))), bw_int_to_fixed(1)));
+			}
+		}
+	}
+	data->tile_width_in_pixels = bw_int_to_fixed(8);
+	data->dmif_total_number_of_data_request_page_close_open = bw_int_to_fixed(0);
+	data->mcifwr_total_number_of_data_request_page_close_open = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (data->scatter_gather_enable_for_pipe[i] == 1 && tiling_mode[i] != bw_def_linear) {
+				data->bytes_per_page_close_open = bw_mul(data->lines_interleaved_in_mem_access[i], bw_max2(bw_mul(bw_mul(bw_mul(bw_int_to_fixed(data->bytes_per_pixel[i]), data->tile_width_in_pixels), bw_int_to_fixed(vbios->number_of_dram_banks)), bw_int_to_fixed(data->number_of_dram_channels)), bw_mul(bw_int_to_fixed(data->bytes_per_pixel[i]), data->scatter_gather_page_width[i])));
+			}
+			else if (data->scatter_gather_enable_for_pipe[i] == 1 && tiling_mode[i] == bw_def_linear && bw_equ(bw_mod((bw_mul(data->pitch_in_pixels_after_surface_type[i], bw_int_to_fixed(data->bytes_per_pixel[i]))), data->inefficient_linear_pitch_in_bytes), bw_int_to_fixed(0))) {
+				data->bytes_per_page_close_open = dceip->linear_mode_line_request_alternation_slice;
+			}
+			else {
+				data->bytes_per_page_close_open = data->memory_chunk_size_in_bytes[i];
+			}
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				data->dmif_total_number_of_data_request_page_close_open = bw_add(data->dmif_total_number_of_data_request_page_close_open, bw_div(bw_ceil2(data->adjusted_data_buffer_size[i], data->memory_chunk_size_in_bytes[i]), data->bytes_per_page_close_open));
+			}
+			else {
+				data->mcifwr_total_number_of_data_request_page_close_open = bw_add(data->mcifwr_total_number_of_data_request_page_close_open, bw_div(bw_ceil2(data->adjusted_data_buffer_size[i], data->memory_chunk_size_in_bytes[i]), data->bytes_per_page_close_open));
+			}
+		}
+	}
+	data->dmif_total_page_close_open_time = bw_div(bw_mul((bw_add(bw_add(data->dmif_total_number_of_data_request_page_close_open, data->scatter_gather_total_pte_request_groups), data->cursor_total_request_groups)), vbios->trc), bw_int_to_fixed(1000));
+	data->mcifwr_total_page_close_open_time = bw_div(bw_mul(data->mcifwr_total_number_of_data_request_page_close_open, vbios->trc), bw_int_to_fixed(1000));
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->adjusted_data_buffer_size_in_memory[i] = bw_div(bw_mul(data->adjusted_data_buffer_size[i], data->bytes_per_request[i]), data->useful_bytes_per_request[i]);
+		}
+	}
+	data->total_requests_for_adjusted_dmif_size = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				data->total_requests_for_adjusted_dmif_size = bw_add(data->total_requests_for_adjusted_dmif_size, bw_div(data->adjusted_data_buffer_size[i], data->useful_bytes_per_request[i]));
+			}
+		}
+	}
+	data->total_dmifmc_urgent_trips = bw_ceil2(bw_div(data->total_requests_for_adjusted_dmif_size, (bw_add(dceip->dmif_request_buffer_size, bw_int_to_fixed(vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel * data->number_of_dram_channels)))), bw_int_to_fixed(1));
+	data->total_dmifmc_urgent_latency = bw_mul(vbios->dmifmc_urgent_latency, data->total_dmifmc_urgent_trips);
+	data->total_display_reads_required_data = bw_int_to_fixed(0);
+	data->total_display_reads_required_dram_access_data = bw_int_to_fixed(0);
+	data->total_display_writes_required_data = bw_int_to_fixed(0);
+	data->total_display_writes_required_dram_access_data = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				data->display_reads_required_data = data->adjusted_data_buffer_size_in_memory[i];
+				/*for hbm memories, each channel is split into 2 pseudo-channels that are each 64 bits in width.  each*/
+				/*pseudo-channel may be read independently of one another.*/
+				/*the read burst length (bl) for hbm memories is 4, so each read command will access 32 bytes of data.*/
+				/*the 64 or 32 byte sized data is stored in one pseudo-channel.*/
+				/*it will take 4 memclk cycles or 8 yclk cycles to fetch 64 bytes of data from the hbm memory (2 read commands).*/
+				/*it will take 2 memclk cycles or 4 yclk cycles to fetch 32 bytes of data from the hbm memory (1 read command).*/
+				/*for gddr5/ddr4 memories, there is additional overhead if the size of the request is smaller than 64 bytes.*/
+				/*the read burst length (bl) for gddr5/ddr4 memories is 8, regardless of the size of the data request.*/
+				/*therefore it will require 8 cycles to fetch 64 or 32 bytes of data from the memory.*/
+				/*the memory efficiency will be 50% for the 32 byte sized data.*/
+				if (vbios->memory_type == bw_def_hbm) {
+					data->display_reads_required_dram_access_data = data->adjusted_data_buffer_size_in_memory[i];
+				}
+				else {
+					data->display_reads_required_dram_access_data = bw_mul(data->adjusted_data_buffer_size_in_memory[i], bw_ceil2(bw_div(bw_int_to_fixed((8 * vbios->dram_channel_width_in_bits / 8)), data->bytes_per_request[i]), bw_int_to_fixed(1)));
+				}
+				data->total_display_reads_required_data = bw_add(data->total_display_reads_required_data, data->display_reads_required_data);
+				data->total_display_reads_required_dram_access_data = bw_add(data->total_display_reads_required_dram_access_data, data->display_reads_required_dram_access_data);
+			}
+			else {
+				data->total_display_writes_required_data = bw_add(data->total_display_writes_required_data, data->adjusted_data_buffer_size_in_memory[i]);
+				data->total_display_writes_required_dram_access_data = bw_add(data->total_display_writes_required_dram_access_data, bw_mul(data->adjusted_data_buffer_size_in_memory[i], bw_ceil2(bw_div(bw_int_to_fixed(vbios->dram_channel_width_in_bits), data->bytes_per_request[i]), bw_int_to_fixed(1))));
+			}
+		}
+	}
+	data->total_display_reads_required_data = bw_add(bw_add(data->total_display_reads_required_data, data->cursor_total_data), bw_mul(data->scatter_gather_total_pte_requests, bw_int_to_fixed(64)));
+	data->total_display_reads_required_dram_access_data = bw_add(bw_add(data->total_display_reads_required_dram_access_data, data->cursor_total_data), bw_mul(data->scatter_gather_total_pte_requests, bw_int_to_fixed(64)));
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_mtn(data->v_filter_init[i], bw_int_to_fixed(4))) {
+				data->src_pixels_for_first_output_pixel[i] = bw_mul(bw_int_to_fixed(4), data->source_width_rounded_up_to_chunks[i]);
+			}
+			else {
+				if (bw_mtn(data->v_filter_init[i], bw_int_to_fixed(2))) {
+					data->src_pixels_for_first_output_pixel[i] = bw_int_to_fixed(512);
+				}
+				else {
+					data->src_pixels_for_first_output_pixel[i] = bw_int_to_fixed(0);
+				}
+			}
+			data->src_data_for_first_output_pixel[i] = bw_div(bw_mul(bw_mul(data->src_pixels_for_first_output_pixel[i], bw_int_to_fixed(data->bytes_per_pixel[i])), data->bytes_per_request[i]), data->useful_bytes_per_request[i]);
+			data->src_pixels_for_last_output_pixel[i] = bw_mul(data->source_width_rounded_up_to_chunks[i], bw_max2(bw_ceil2(data->v_filter_init[i], bw_int_to_fixed(dceip->lines_interleaved_into_lb)), bw_mul(bw_ceil2(data->vsr[i], bw_int_to_fixed(dceip->lines_interleaved_into_lb)), data->horizontal_blank_and_chunk_granularity_factor[i])));
+			data->src_data_for_last_output_pixel[i] = bw_div(bw_mul(bw_mul(bw_mul(data->source_width_rounded_up_to_chunks[i], bw_max2(bw_ceil2(data->v_filter_init[i], bw_int_to_fixed(dceip->lines_interleaved_into_lb)), data->lines_interleaved_in_mem_access[i])), bw_int_to_fixed(data->bytes_per_pixel[i])), data->bytes_per_request[i]), data->useful_bytes_per_request[i]);
+			data->active_time[i] = bw_div(bw_div(data->source_width_rounded_up_to_chunks[i], data->hsr[i]), data->pixel_rate[i]);
+		}
+	}
+	for (i = 0; i <= 2; i++) {
+		for (j = 0; j <= 7; j++) {
+			data->dmif_burst_time[i][j] = bw_max3(data->dmif_total_page_close_open_time, bw_div(data->total_display_reads_required_dram_access_data, (bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[i]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels)))), bw_div(data->total_display_reads_required_data, (bw_mul(bw_mul(sclk[j], vbios->data_return_bus_width), bw_frc_to_fixed(dceip->percent_of_ideal_port_bw_received_after_urgent_latency, 100)))));
+			if (data->d1_display_write_back_dwb_enable == 1) {
+				data->mcifwr_burst_time[i][j] = bw_max3(data->mcifwr_total_page_close_open_time, bw_div(data->total_display_writes_required_dram_access_data, (bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[i]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_wrchannels)))), bw_div(data->total_display_writes_required_data, (bw_mul(sclk[j], vbios->data_return_bus_width))));
+			}
+		}
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		for (j = 0; j <= 2; j++) {
+			for (k = 0; k <= 7; k++) {
+				if (data->enable[i]) {
+					if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+						/*time to transfer data from the dmif buffer to the lb.  since the mc to dmif transfer time overlaps*/
+						/*with the dmif to lb transfer time, only time to transfer the last chunk  is considered.*/
+						data->dmif_buffer_transfer_time[i] = bw_mul(data->source_width_rounded_up_to_chunks[i], (bw_div(dceip->lb_write_pixels_per_dispclk, (bw_div(vbios->low_voltage_max_dispclk, dceip->display_pipe_throughput_factor)))));
+						data->line_source_transfer_time[i][j][k] = bw_max2(bw_mul((bw_add(data->total_dmifmc_urgent_latency, data->dmif_burst_time[j][k])), bw_floor2(bw_div(data->src_data_for_first_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1))), bw_sub(bw_add(bw_mul((bw_add(data->total_dmifmc_urgent_latency, data->dmif_burst_time[j][k])), bw_floor2(bw_div(data->src_data_for_last_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1))), data->dmif_buffer_transfer_time[i]), data->active_time[i]));
+						/*during an mclk switch the requests from the dce ip are stored in the gmc/arb.  these requests should be serviced immediately*/
+						/*after the mclk switch sequence and not incur an urgent latency penalty.  it is assumed that the gmc/arb can hold up to 256 requests*/
+						/*per memory channel.  if the dce ip is urgent after the mclk switch sequence, all pending requests and subsequent requests should be*/
+						/*immediately serviced without a gap in the urgent requests.*/
+						/*the latency incurred would be the time to issue the requests and return the data for the first or last output pixel.*/
+						if (surface_type[i] == bw_def_graphics) {
+							switch (data->lb_bpc[i]) {
+							case 6:
+								data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency6_bit_per_component;
+								break;
+							case 8:
+								data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency8_bit_per_component;
+								break;
+							case 10:
+								data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency10_bit_per_component;
+								break;
+							default:
+								data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency12_bit_per_component;
+								break;
+							}
+							if (data->use_alpha[i] == 1) {
+								data->v_scaler_efficiency = bw_min2(data->v_scaler_efficiency, dceip->alpha_vscaler_efficiency);
+							}
+						}
+						else {
+							switch (data->lb_bpc[i]) {
+							case 6:
+								data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency6_bit_per_component;
+								break;
+							case 8:
+								data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency8_bit_per_component;
+								break;
+							case 10:
+								data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency10_bit_per_component;
+								break;
+							default:
+								data->v_scaler_efficiency = bw_int_to_fixed(3);
+								break;
+							}
+						}
+						if (dceip->pre_downscaler_enabled && bw_mtn(data->hsr[i], bw_int_to_fixed(1))) {
+							data->scaler_limits_factor = bw_max2(bw_div(data->v_taps[i], data->v_scaler_efficiency), bw_div(data->source_width_rounded_up_to_chunks[i], data->h_total[i]));
+						}
+						else {
+							data->scaler_limits_factor = bw_max3(bw_int_to_fixed(1), bw_ceil2(bw_div(data->h_taps[i], bw_int_to_fixed(4)), bw_int_to_fixed(1)), bw_mul(data->hsr[i], bw_max2(bw_div(data->v_taps[i], data->v_scaler_efficiency), bw_int_to_fixed(1))));
+						}
+						data->dram_speed_change_line_source_transfer_time[i][j][k] = bw_mul(bw_int_to_fixed(2), bw_max2((bw_add((bw_div(data->src_data_for_first_output_pixel[i], bw_min2(bw_mul(data->bytes_per_request[i], sclk[k]), bw_div(bw_mul(bw_mul(data->bytes_per_request[i], data->pixel_rate[i]), data->scaler_limits_factor), bw_int_to_fixed(2))))), (bw_mul(data->dmif_burst_time[j][k], bw_floor2(bw_div(data->src_data_for_first_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1)))))), (bw_add((bw_div(data->src_data_for_last_output_pixel[i], bw_min2(bw_mul(data->bytes_per_request[i], sclk[k]), bw_div(bw_mul(bw_mul(data->bytes_per_request[i], data->pixel_rate[i]), data->scaler_limits_factor), bw_int_to_fixed(2))))), (bw_sub(bw_mul(data->dmif_burst_time[j][k], bw_floor2(bw_div(data->src_data_for_last_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1))), data->active_time[i]))))));
+					}
+					else {
+						data->line_source_transfer_time[i][j][k] = bw_max2(bw_mul((bw_add(vbios->mcifwrmc_urgent_latency, data->mcifwr_burst_time[j][k])), bw_floor2(bw_div(data->src_data_for_first_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1))), bw_sub(bw_mul((bw_add(vbios->mcifwrmc_urgent_latency, data->mcifwr_burst_time[j][k])), bw_floor2(bw_div(data->src_data_for_last_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1))), data->active_time[i]));
+						/*during an mclk switch the requests from the dce ip are stored in the gmc/arb.  these requests should be serviced immediately*/
+						/*after the mclk switch sequence and not incur an urgent latency penalty.  it is assumed that the gmc/arb can hold up to 256 requests*/
+						/*per memory channel.  if the dce ip is urgent after the mclk switch sequence, all pending requests and subsequent requests should be*/
+						/*immediately serviced without a gap in the urgent requests.*/
+						/*the latency incurred would be the time to issue the requests and return the data for the first or last output pixel.*/
+						data->dram_speed_change_line_source_transfer_time[i][j][k] = bw_max2((bw_add((bw_div(data->src_data_for_first_output_pixel[i], bw_min2(bw_mul(data->bytes_per_request[i], sclk[k]), bw_div(bw_mul(data->bytes_per_request[i], vbios->low_voltage_max_dispclk), bw_int_to_fixed(2))))), (bw_mul(data->mcifwr_burst_time[j][k], bw_floor2(bw_div(data->src_data_for_first_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1)))))), (bw_add((bw_div(data->src_data_for_last_output_pixel[i], bw_min2(bw_mul(data->bytes_per_request[i], sclk[k]), bw_div(bw_mul(data->bytes_per_request[i], vbios->low_voltage_max_dispclk), bw_int_to_fixed(2))))), (bw_sub(bw_mul(data->mcifwr_burst_time[j][k], bw_floor2(bw_div(data->src_data_for_last_output_pixel[i], data->adjusted_data_buffer_size_in_memory[i]), bw_int_to_fixed(1))), data->active_time[i])))));
+					}
+				}
+			}
+		}
+	}
+	/*cpu c-state and p-state change enable*/
+	/*for cpu p-state change to be possible for a yclk(pclk) and sclk level the dispclk required has to be enough for the blackout duration*/
+	/*for cpu c-state change to be possible for a yclk(pclk) and sclk level the dispclk required has to be enough for the blackout duration and recovery*/
+	/*condition for the blackout duration:*/
+	/* minimum latency hiding > blackout duration + dmif burst time + line source transfer time*/
+	/*condition for the blackout recovery:*/
+	/* recovery time >  dmif burst time + 2 * urgent latency*/
+	/* recovery time > (display bw * blackout duration  + (2 * urgent latency + dmif burst time)*dispclk - dmif size )*/
+	/*                  / (dispclk - display bw)*/
+	/*the minimum latency hiding is the minimum for all pipes of one screen line time, plus one more line time if doing lb prefetch, plus the dmif data buffer size equivalent in time, minus the urgent latency.*/
+	/*the minimum latency hiding is  further limited by the cursor.  the cursor latency hiding is the number of lines of the cursor buffer, minus one if the downscaling is less than two, or minus three if it is more*/
+
+	/*initialize variables*/
+	number_of_displays_enabled = 0;
+	number_of_displays_enabled_with_margin = 0;
+	for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+		if (data->enable[k]) {
+			number_of_displays_enabled = number_of_displays_enabled + 1;
+		}
+		data->display_pstate_change_enable[k] = 0;
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if ((bw_equ(dceip->stutter_and_dram_clock_state_change_gated_before_cursor, bw_int_to_fixed(0)) && bw_mtn(data->cursor_width_pixels[i], bw_int_to_fixed(0)))) {
+				if (bw_ltn(data->vsr[i], bw_int_to_fixed(2))) {
+					data->cursor_latency_hiding[i] = bw_div(bw_div(bw_mul((bw_sub(dceip->cursor_dcp_buffer_lines, bw_int_to_fixed(1))), data->h_total[i]), data->vsr[i]), data->pixel_rate[i]);
+				}
+				else {
+					data->cursor_latency_hiding[i] = bw_div(bw_div(bw_mul((bw_sub(dceip->cursor_dcp_buffer_lines, bw_int_to_fixed(3))), data->h_total[i]), data->vsr[i]), data->pixel_rate[i]);
+				}
+			}
+			else {
+				data->cursor_latency_hiding[i] = bw_int_to_fixed(9999);
+			}
+		}
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (dceip->graphics_lb_nodownscaling_multi_line_prefetching == 1 && (bw_equ(data->vsr[i], bw_int_to_fixed(1)) || (bw_leq(data->vsr[i], bw_frc_to_fixed(8, 10)) && bw_leq(data->v_taps[i], bw_int_to_fixed(2)) && data->lb_bpc[i] == 8)) && surface_type[i] == bw_def_graphics) {
+				if (number_of_displays_enabled > 2)
+					data->minimum_latency_hiding[i] = bw_sub(bw_div(bw_mul((bw_div((bw_add(bw_sub(data->lb_partitions[i], bw_int_to_fixed(2)), bw_div(bw_div(data->data_buffer_size[i], bw_int_to_fixed(data->bytes_per_pixel[i])), data->source_width_pixels[i]))), data->vsr[i])), data->h_total[i]), data->pixel_rate[i]), data->total_dmifmc_urgent_latency);
+				else
+					data->minimum_latency_hiding[i] = bw_sub(bw_div(bw_mul((bw_div((bw_add(bw_sub(data->lb_partitions[i], bw_int_to_fixed(1)), bw_div(bw_div(data->data_buffer_size[i], bw_int_to_fixed(data->bytes_per_pixel[i])), data->source_width_pixels[i]))), data->vsr[i])), data->h_total[i]), data->pixel_rate[i]), data->total_dmifmc_urgent_latency);
+			}
+			else {
+				data->minimum_latency_hiding[i] = bw_sub(bw_div(bw_mul((bw_div((bw_add(bw_int_to_fixed(1 + data->line_buffer_prefetch[i]), bw_div(bw_div(data->data_buffer_size[i], bw_int_to_fixed(data->bytes_per_pixel[i])), data->source_width_pixels[i]))), data->vsr[i])), data->h_total[i]), data->pixel_rate[i]), data->total_dmifmc_urgent_latency);
+			}
+			data->minimum_latency_hiding_with_cursor[i] = bw_min2(data->minimum_latency_hiding[i], data->cursor_latency_hiding[i]);
+		}
+	}
+	for (i = 0; i <= 2; i++) {
+		for (j = 0; j <= 7; j++) {
+			data->blackout_duration_margin[i][j] = bw_int_to_fixed(9999);
+			data->dispclk_required_for_blackout_duration[i][j] = bw_int_to_fixed(0);
+			data->dispclk_required_for_blackout_recovery[i][j] = bw_int_to_fixed(0);
+			for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+				if (data->enable[k] && bw_mtn(vbios->blackout_duration, bw_int_to_fixed(0))) {
+					if (surface_type[k] != bw_def_display_write_back420_luma && surface_type[k] != bw_def_display_write_back420_chroma) {
+						data->blackout_duration_margin[i][j] = bw_min2(data->blackout_duration_margin[i][j], bw_sub(bw_sub(bw_sub(data->minimum_latency_hiding_with_cursor[k], vbios->blackout_duration), data->dmif_burst_time[i][j]), data->line_source_transfer_time[k][i][j]));
+						data->dispclk_required_for_blackout_duration[i][j] = bw_max3(data->dispclk_required_for_blackout_duration[i][j], bw_div(bw_div(bw_mul(data->src_pixels_for_first_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_sub(bw_sub(data->minimum_latency_hiding_with_cursor[k], vbios->blackout_duration), data->dmif_burst_time[i][j]))), bw_div(bw_div(bw_mul(data->src_pixels_for_last_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_add(bw_sub(bw_sub(data->minimum_latency_hiding_with_cursor[k], vbios->blackout_duration), data->dmif_burst_time[i][j]), data->active_time[k]))));
+						if (bw_leq(vbios->maximum_blackout_recovery_time, bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[i][j]))) {
+							data->dispclk_required_for_blackout_recovery[i][j] = bw_int_to_fixed(9999);
+						}
+						else if (bw_ltn(data->adjusted_data_buffer_size[k], bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), (bw_add(vbios->blackout_duration, bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[i][j])))))) {
+							data->dispclk_required_for_blackout_recovery[i][j] = bw_max2(data->dispclk_required_for_blackout_recovery[i][j], bw_div(bw_mul(bw_div(bw_div((bw_sub(bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), (bw_add(vbios->blackout_duration, vbios->maximum_blackout_recovery_time))), data->adjusted_data_buffer_size[k])), bw_int_to_fixed(data->bytes_per_pixel[k])), (bw_sub(vbios->maximum_blackout_recovery_time, bw_sub(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[i][j])))), data->latency_hiding_lines[k]), data->lines_interleaved_in_mem_access[k]));
+						}
+					}
+					else {
+						data->blackout_duration_margin[i][j] = bw_min2(data->blackout_duration_margin[i][j], bw_sub(bw_sub(bw_sub(bw_sub(data->minimum_latency_hiding_with_cursor[k], vbios->blackout_duration), data->dmif_burst_time[i][j]), data->mcifwr_burst_time[i][j]), data->line_source_transfer_time[k][i][j]));
+						data->dispclk_required_for_blackout_duration[i][j] = bw_max3(data->dispclk_required_for_blackout_duration[i][j], bw_div(bw_div(bw_mul(data->src_pixels_for_first_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_sub(bw_sub(bw_sub(data->minimum_latency_hiding_with_cursor[k], vbios->blackout_duration), data->dmif_burst_time[i][j]), data->mcifwr_burst_time[i][j]))), bw_div(bw_div(bw_mul(data->src_pixels_for_last_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_add(bw_sub(bw_sub(bw_sub(data->minimum_latency_hiding_with_cursor[k], vbios->blackout_duration), data->dmif_burst_time[i][j]), data->mcifwr_burst_time[i][j]), data->active_time[k]))));
+						if (bw_ltn(vbios->maximum_blackout_recovery_time, bw_add(bw_add(bw_mul(bw_int_to_fixed(2), vbios->mcifwrmc_urgent_latency), data->dmif_burst_time[i][j]), data->mcifwr_burst_time[i][j]))) {
+							data->dispclk_required_for_blackout_recovery[i][j] = bw_int_to_fixed(9999);
+						}
+						else if (bw_ltn(data->adjusted_data_buffer_size[k], bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), (bw_add(vbios->blackout_duration, bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[i][j])))))) {
+							data->dispclk_required_for_blackout_recovery[i][j] = bw_max2(data->dispclk_required_for_blackout_recovery[i][j], bw_div(bw_mul(bw_div(bw_div((bw_sub(bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), (bw_add(vbios->blackout_duration, vbios->maximum_blackout_recovery_time))), data->adjusted_data_buffer_size[k])), bw_int_to_fixed(data->bytes_per_pixel[k])), (bw_sub(vbios->maximum_blackout_recovery_time, (bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[i][j]))))), data->latency_hiding_lines[k]), data->lines_interleaved_in_mem_access[k]));
+						}
+					}
+				}
+			}
+		}
+	}
+	if (bw_mtn(data->blackout_duration_margin[high][s_high], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[high][s_high], vbios->high_voltage_max_dispclk)) {
+		data->cpup_state_change_enable = bw_def_yes;
+		if (bw_ltn(data->dispclk_required_for_blackout_recovery[high][s_high], vbios->high_voltage_max_dispclk)) {
+			data->cpuc_state_change_enable = bw_def_yes;
+		}
+		else {
+			data->cpuc_state_change_enable = bw_def_no;
+		}
+	}
+	else {
+		data->cpup_state_change_enable = bw_def_no;
+		data->cpuc_state_change_enable = bw_def_no;
+	}
+	/*nb p-state change enable*/
+	/*for dram speed/p-state change to be possible for a yclk(pclk) and sclk level there has to be positive margin and the dispclk required has to be*/
+	/*below the maximum.*/
+	/*the dram speed/p-state change margin is the minimum for all surfaces of the maximum latency hiding minus the dram speed/p-state change latency,*/
+	/*minus the dmif burst time, minus the source line transfer time*/
+	/*the maximum latency hiding is the minimum latency hiding plus one source line used for de-tiling in the line buffer, plus half the urgent latency*/
+	/*if stutter and dram clock state change are gated before cursor then the cursor latency hiding does not limit stutter or dram clock state change*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			/*maximum_latency_hiding(i) = minimum_latency_hiding(i) + 1 / vsr(i) **/
+			/*      h_total(i) / pixel_rate(i) + 0.5 * total_dmifmc_urgent_latency*/
+			data->maximum_latency_hiding[i] = bw_add(data->minimum_latency_hiding[i],
+				bw_mul(bw_frc_to_fixed(5, 10), data->total_dmifmc_urgent_latency));
+			data->maximum_latency_hiding_with_cursor[i] = bw_min2(data->maximum_latency_hiding[i], data->cursor_latency_hiding[i]);
+		}
+	}
+	for (i = 0; i <= 2; i++) {
+		for (j = 0; j <= 7; j++) {
+			data->min_dram_speed_change_margin[i][j] = bw_int_to_fixed(9999);
+			data->dram_speed_change_margin = bw_int_to_fixed(9999);
+			data->dispclk_required_for_dram_speed_change[i][j] = bw_int_to_fixed(0);
+			data->num_displays_with_margin[i][j] = 0;
+			for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+				if (data->enable[k]) {
+					if (surface_type[k] != bw_def_display_write_back420_luma && surface_type[k] != bw_def_display_write_back420_chroma) {
+						data->dram_speed_change_margin = bw_sub(bw_sub(bw_sub(data->maximum_latency_hiding_with_cursor[k], vbios->nbp_state_change_latency), data->dmif_burst_time[i][j]), data->dram_speed_change_line_source_transfer_time[k][i][j]);
+						if ((bw_mtn(data->dram_speed_change_margin, bw_int_to_fixed(0)) && bw_ltn(data->dram_speed_change_margin, bw_int_to_fixed(9999)))) {
+							/*determine the minimum dram clock change margin for each set of clock frequencies*/
+							data->min_dram_speed_change_margin[i][j] = bw_min2(data->min_dram_speed_change_margin[i][j], data->dram_speed_change_margin);
+							/*compute the maximum clock frequuency required for the dram clock change at each set of clock frequencies*/
+							data->dispclk_required_for_dram_speed_change_pipe[i][j] = bw_max2(bw_div(bw_div(bw_mul(data->src_pixels_for_first_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_sub(bw_sub(bw_sub(data->maximum_latency_hiding_with_cursor[k], vbios->nbp_state_change_latency), data->dmif_burst_time[i][j]), data->dram_speed_change_line_source_transfer_time[k][i][j]))), bw_div(bw_div(bw_mul(data->src_pixels_for_last_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_add(bw_sub(bw_sub(bw_sub(data->maximum_latency_hiding_with_cursor[k], vbios->nbp_state_change_latency), data->dmif_burst_time[i][j]), data->dram_speed_change_line_source_transfer_time[k][i][j]), data->active_time[k]))));
+							if ((bw_ltn(data->dispclk_required_for_dram_speed_change_pipe[i][j], vbios->high_voltage_max_dispclk))) {
+								data->display_pstate_change_enable[k] = 1;
+								data->num_displays_with_margin[i][j] = data->num_displays_with_margin[i][j] + 1;
+								data->dispclk_required_for_dram_speed_change[i][j] = bw_max2(data->dispclk_required_for_dram_speed_change[i][j], data->dispclk_required_for_dram_speed_change_pipe[i][j]);
+							}
+						}
+					}
+					else {
+						data->dram_speed_change_margin = bw_sub(bw_sub(bw_sub(bw_sub(data->maximum_latency_hiding_with_cursor[k], vbios->nbp_state_change_latency), data->dmif_burst_time[i][j]), data->mcifwr_burst_time[i][j]), data->dram_speed_change_line_source_transfer_time[k][i][j]);
+						if ((bw_mtn(data->dram_speed_change_margin, bw_int_to_fixed(0)) && bw_ltn(data->dram_speed_change_margin, bw_int_to_fixed(9999)))) {
+							/*determine the minimum dram clock change margin for each display pipe*/
+							data->min_dram_speed_change_margin[i][j] = bw_min2(data->min_dram_speed_change_margin[i][j], data->dram_speed_change_margin);
+							/*compute the maximum clock frequuency required for the dram clock change at each set of clock frequencies*/
+							data->dispclk_required_for_dram_speed_change_pipe[i][j] = bw_max2(bw_div(bw_div(bw_mul(data->src_pixels_for_first_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_sub(bw_sub(bw_sub(bw_sub(data->maximum_latency_hiding_with_cursor[k], vbios->nbp_state_change_latency), data->dmif_burst_time[i][j]), data->dram_speed_change_line_source_transfer_time[k][i][j]), data->mcifwr_burst_time[i][j]))), bw_div(bw_div(bw_mul(data->src_pixels_for_last_output_pixel[k], dceip->display_pipe_throughput_factor), dceip->lb_write_pixels_per_dispclk), (bw_add(bw_sub(bw_sub(bw_sub(bw_sub(data->maximum_latency_hiding_with_cursor[k], vbios->nbp_state_change_latency), data->dmif_burst_time[i][j]), data->dram_speed_change_line_source_transfer_time[k][i][j]), data->mcifwr_burst_time[i][j]), data->active_time[k]))));
+							if ((bw_ltn(data->dispclk_required_for_dram_speed_change_pipe[i][j], vbios->high_voltage_max_dispclk))) {
+								data->display_pstate_change_enable[k] = 1;
+								data->num_displays_with_margin[i][j] = data->num_displays_with_margin[i][j] + 1;
+								data->dispclk_required_for_dram_speed_change[i][j] = bw_max2(data->dispclk_required_for_dram_speed_change[i][j], data->dispclk_required_for_dram_speed_change_pipe[i][j]);
+							}
+						}
+					}
+				}
+			}
+		}
+	}
+	/*determine the number of displays with margin to switch in the v_active region*/
+	for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+		if (data->enable[k] == 1 && data->display_pstate_change_enable[k] == 1) {
+			number_of_displays_enabled_with_margin = number_of_displays_enabled_with_margin + 1;
+		}
+	}
+	/*determine the number of displays that don't have any dram clock change margin, but*/
+	/*have the same resolution.  these displays can switch in a common vblank region if*/
+	/*their frames are aligned.*/
+	data->min_vblank_dram_speed_change_margin = bw_int_to_fixed(9999);
+	for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+		if (data->enable[k]) {
+			if (surface_type[k] != bw_def_display_write_back420_luma && surface_type[k] != bw_def_display_write_back420_chroma) {
+				data->v_blank_dram_speed_change_margin[k] = bw_sub(bw_sub(bw_sub(bw_div(bw_mul((bw_sub(data->v_total[k], bw_sub(bw_div(data->src_height[k], data->v_scale_ratio[k]), bw_int_to_fixed(4)))), data->h_total[k]), data->pixel_rate[k]), vbios->nbp_state_change_latency), data->dmif_burst_time[low][s_low]), data->dram_speed_change_line_source_transfer_time[k][low][s_low]);
+				data->min_vblank_dram_speed_change_margin = bw_min2(data->min_vblank_dram_speed_change_margin, data->v_blank_dram_speed_change_margin[k]);
+			}
+			else {
+				data->v_blank_dram_speed_change_margin[k] = bw_sub(bw_sub(bw_sub(bw_sub(bw_div(bw_mul((bw_sub(data->v_total[k], bw_sub(bw_div(data->src_height[k], data->v_scale_ratio[k]), bw_int_to_fixed(4)))), data->h_total[k]), data->pixel_rate[k]), vbios->nbp_state_change_latency), data->dmif_burst_time[low][s_low]), data->mcifwr_burst_time[low][s_low]), data->dram_speed_change_line_source_transfer_time[k][low][s_low]);
+				data->min_vblank_dram_speed_change_margin = bw_min2(data->min_vblank_dram_speed_change_margin, data->v_blank_dram_speed_change_margin[k]);
+			}
+		}
+	}
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		data->displays_with_same_mode[i] = bw_int_to_fixed(0);
+		if (data->enable[i] == 1 && data->display_pstate_change_enable[i] == 0 && bw_mtn(data->v_blank_dram_speed_change_margin[i], bw_int_to_fixed(0))) {
+			for (j = 0; j <= maximum_number_of_surfaces - 1; j++) {
+				if ((i == j || data->display_synchronization_enabled) && (data->enable[j] == 1 && bw_equ(data->source_width_rounded_up_to_chunks[i], data->source_width_rounded_up_to_chunks[j]) && bw_equ(data->source_height_rounded_up_to_chunks[i], data->source_height_rounded_up_to_chunks[j]) && bw_equ(data->vsr[i], data->vsr[j]) && bw_equ(data->hsr[i], data->hsr[j]) && bw_equ(data->pixel_rate[i], data->pixel_rate[j]))) {
+					data->displays_with_same_mode[i] = bw_add(data->displays_with_same_mode[i], bw_int_to_fixed(1));
+				}
+			}
+		}
+	}
+	/*compute the maximum number of aligned displays with no margin*/
+	number_of_aligned_displays_with_no_margin = 0;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		number_of_aligned_displays_with_no_margin = bw_fixed_to_int(bw_max2(bw_int_to_fixed(number_of_aligned_displays_with_no_margin), data->displays_with_same_mode[i]));
+	}
+	/*dram clock change is possible, if all displays have positive margin except for one display or a group of*/
+	/*aligned displays with the same timing.*/
+	/*the display(s) with the negative margin can be switched in the v_blank region while the other*/
+	/*displays are in v_blank or v_active.*/
+	if (number_of_displays_enabled_with_margin > 0 && (number_of_displays_enabled_with_margin + number_of_aligned_displays_with_no_margin) == number_of_displays_enabled && bw_mtn(data->min_dram_speed_change_margin[high][s_high], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[high][s_high], bw_int_to_fixed(9999)) && bw_ltn(data->dispclk_required_for_dram_speed_change[high][s_high], vbios->high_voltage_max_dispclk)) {
+		data->nbp_state_change_enable = bw_def_yes;
+	}
+	else {
+		data->nbp_state_change_enable = bw_def_no;
+	}
+	/*dram clock change is possible only in vblank if all displays are aligned and have no margin*/
+	if (number_of_aligned_displays_with_no_margin == number_of_displays_enabled) {
+		nbp_state_change_enable_blank = bw_def_yes;
+	}
+	else {
+		nbp_state_change_enable_blank = bw_def_no;
+	}
+
+	/*average bandwidth*/
+	/*the average bandwidth with no compression is the vertical active time is the source width times the bytes per pixel divided by the line time, multiplied by the vertical scale ratio and the ratio of bytes per request divided by the useful bytes per request.*/
+	/*the average bandwidth with compression is the same, divided by the compression ratio*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->average_bandwidth_no_compression[i] = bw_div(bw_mul(bw_mul(bw_div(bw_mul(data->source_width_rounded_up_to_chunks[i], bw_int_to_fixed(data->bytes_per_pixel[i])), (bw_div(data->h_total[i], data->pixel_rate[i]))), data->vsr[i]), data->bytes_per_request[i]), data->useful_bytes_per_request[i]);
+			data->average_bandwidth[i] = bw_div(data->average_bandwidth_no_compression[i], data->compression_rate[i]);
+		}
+	}
+	data->total_average_bandwidth_no_compression = bw_int_to_fixed(0);
+	data->total_average_bandwidth = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->total_average_bandwidth_no_compression = bw_add(data->total_average_bandwidth_no_compression, data->average_bandwidth_no_compression[i]);
+			data->total_average_bandwidth = bw_add(data->total_average_bandwidth, data->average_bandwidth[i]);
+		}
+	}
+
+	/*required yclk(pclk)*/
+	/*yclk requirement only makes sense if the dmif and mcifwr data total page close-open time is less than the time for data transfer and the total pte requests fit in the scatter-gather saw queque size*/
+	/*if that is the case, the yclk requirement is the maximum of the ones required by dmif and mcifwr, and the high/low yclk(pclk) is chosen accordingly*/
+	/*high yclk(pclk) has to be selected when dram speed/p-state change is not possible.*/
+	data->min_cursor_memory_interface_buffer_size_in_time = bw_int_to_fixed(9999);
+	/* number of cursor lines stored in the cursor data return buffer*/
+	num_cursor_lines = 0;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_mtn(data->cursor_width_pixels[i], bw_int_to_fixed(0))) {
+				/*compute number of cursor lines stored in data return buffer*/
+				if (bw_leq(data->cursor_width_pixels[i], bw_int_to_fixed(64)) && dceip->large_cursor == 1) {
+					num_cursor_lines = 4;
+				}
+				else {
+					num_cursor_lines = 2;
+				}
+				data->min_cursor_memory_interface_buffer_size_in_time = bw_min2(data->min_cursor_memory_interface_buffer_size_in_time, bw_div(bw_mul(bw_div(bw_int_to_fixed(num_cursor_lines), data->vsr[i]), data->h_total[i]), data->pixel_rate[i]));
+			}
+		}
+	}
+	/*compute minimum time to read one chunk from the dmif buffer*/
+	if (number_of_displays_enabled > 2) {
+		data->chunk_request_delay = 0;
+	}
+	else {
+		data->chunk_request_delay = bw_fixed_to_int(bw_div(bw_int_to_fixed(512), vbios->high_voltage_max_dispclk));
+	}
+	data->min_read_buffer_size_in_time = bw_min2(data->min_cursor_memory_interface_buffer_size_in_time, data->min_dmif_size_in_time);
+	data->display_reads_time_for_data_transfer = bw_sub(bw_sub(data->min_read_buffer_size_in_time, data->total_dmifmc_urgent_latency), bw_int_to_fixed(data->chunk_request_delay));
+	data->display_writes_time_for_data_transfer = bw_sub(data->min_mcifwr_size_in_time, vbios->mcifwrmc_urgent_latency);
+	data->dmif_required_dram_bandwidth = bw_div(data->total_display_reads_required_dram_access_data, data->display_reads_time_for_data_transfer);
+	data->mcifwr_required_dram_bandwidth = bw_div(data->total_display_writes_required_dram_access_data, data->display_writes_time_for_data_transfer);
+	data->required_dmifmc_urgent_latency_for_page_close_open = bw_div((bw_sub(data->min_read_buffer_size_in_time, data->dmif_total_page_close_open_time)), data->total_dmifmc_urgent_trips);
+	data->required_mcifmcwr_urgent_latency = bw_sub(data->min_mcifwr_size_in_time, data->mcifwr_total_page_close_open_time);
+	if (bw_mtn(data->scatter_gather_total_pte_requests, dceip->maximum_total_outstanding_pte_requests_allowed_by_saw)) {
+		data->required_dram_bandwidth_gbyte_per_second = bw_int_to_fixed(9999);
+		yclk_message = bw_def_exceeded_allowed_outstanding_pte_req_queue_size;
+		data->y_clk_level = high;
+		data->dram_bandwidth = bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[high]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels));
+	}
+	else if (bw_mtn(vbios->dmifmc_urgent_latency, data->required_dmifmc_urgent_latency_for_page_close_open) || bw_mtn(vbios->mcifwrmc_urgent_latency, data->required_mcifmcwr_urgent_latency)) {
+		data->required_dram_bandwidth_gbyte_per_second = bw_int_to_fixed(9999);
+		yclk_message = bw_def_exceeded_allowed_page_close_open;
+		data->y_clk_level = high;
+		data->dram_bandwidth = bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[high]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels));
+	}
+	else {
+		data->required_dram_bandwidth_gbyte_per_second = bw_div(bw_max2(data->dmif_required_dram_bandwidth, data->mcifwr_required_dram_bandwidth), bw_int_to_fixed(1000));
+		if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation, 100),yclk[low]),bw_div(bw_int_to_fixed(vbios->dram_channel_width_in_bits),bw_int_to_fixed(8))),bw_int_to_fixed(vbios->number_of_dram_channels)))
+				&& bw_ltn(bw_mul(data->required_dram_bandwidth_gbyte_per_second, bw_int_to_fixed(1000)), bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[low]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels))) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[low][s_high], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[low][s_high], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[low][s_high], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[low][s_high], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[low][s_high], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[low][s_high], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[low][s_high], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[low][s_high], vbios->high_voltage_max_dispclk) && data->num_displays_with_margin[low][s_high] == number_of_displays_enabled_with_margin))) {
+			yclk_message = bw_fixed_to_int(vbios->low_yclk);
+			data->y_clk_level = low;
+			data->dram_bandwidth = bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[low]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels));
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation, 100),yclk[mid]),bw_div(bw_int_to_fixed(vbios->dram_channel_width_in_bits),bw_int_to_fixed(8))),bw_int_to_fixed(vbios->number_of_dram_channels)))
+				&& bw_ltn(bw_mul(data->required_dram_bandwidth_gbyte_per_second, bw_int_to_fixed(1000)), bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[mid]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels))) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[mid][s_high], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[mid][s_high], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[mid][s_high], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[mid][s_high], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[mid][s_high], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[mid][s_high], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[mid][s_high], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[mid][s_high], vbios->high_voltage_max_dispclk) && data->num_displays_with_margin[mid][s_high] == number_of_displays_enabled_with_margin))) {
+			yclk_message = bw_fixed_to_int(vbios->mid_yclk);
+			data->y_clk_level = mid;
+			data->dram_bandwidth = bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[mid]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels));
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation, 100),yclk[high]),bw_div(bw_int_to_fixed(vbios->dram_channel_width_in_bits),bw_int_to_fixed(8))),bw_int_to_fixed(vbios->number_of_dram_channels)))
+				&& bw_ltn(bw_mul(data->required_dram_bandwidth_gbyte_per_second, bw_int_to_fixed(1000)), bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[high]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels)))) {
+			yclk_message = bw_fixed_to_int(vbios->high_yclk);
+			data->y_clk_level = high;
+			data->dram_bandwidth = bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[high]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels));
+		}
+		else {
+			yclk_message = bw_def_exceeded_allowed_maximum_bw;
+			data->y_clk_level = high;
+			data->dram_bandwidth = bw_mul(bw_div(bw_mul(bw_mul(data->dram_efficiency, yclk[high]), bw_int_to_fixed(vbios->dram_channel_width_in_bits)), bw_int_to_fixed(8)), bw_int_to_fixed(data->number_of_dram_channels));
+		}
+	}
+	/*required sclk*/
+	/*sclk requirement only makes sense if the total pte requests fit in the scatter-gather saw queque size*/
+	/*if that is the case, the sclk requirement is the maximum of the ones required by dmif and mcifwr, and the high/mid/low sclk is chosen accordingly, unless that choice results in foresaking dram speed/nb p-state change.*/
+	/*the dmif and mcifwr sclk required is the one that allows the transfer of all pipe's data buffer size through the sclk bus in the time for data transfer*/
+	/*for dmif, pte and cursor requests have to be included.*/
+	data->dmif_required_sclk = bw_div(bw_div(data->total_display_reads_required_data, data->display_reads_time_for_data_transfer), (bw_mul(vbios->data_return_bus_width, bw_frc_to_fixed(dceip->percent_of_ideal_port_bw_received_after_urgent_latency, 100))));
+	data->mcifwr_required_sclk = bw_div(bw_div(data->total_display_writes_required_data, data->display_writes_time_for_data_transfer), vbios->data_return_bus_width);
+	if (bw_mtn(data->scatter_gather_total_pte_requests, dceip->maximum_total_outstanding_pte_requests_allowed_by_saw)) {
+		data->required_sclk = bw_int_to_fixed(9999);
+		sclk_message = bw_def_exceeded_allowed_outstanding_pte_req_queue_size;
+		data->sclk_level = s_high;
+	}
+	else if (bw_mtn(vbios->dmifmc_urgent_latency, data->required_dmifmc_urgent_latency_for_page_close_open) || bw_mtn(vbios->mcifwrmc_urgent_latency, data->required_mcifmcwr_urgent_latency)) {
+		data->required_sclk = bw_int_to_fixed(9999);
+		sclk_message = bw_def_exceeded_allowed_page_close_open;
+		data->sclk_level = s_high;
+	}
+	else {
+		data->required_sclk = bw_max2(data->dmif_required_sclk, data->mcifwr_required_sclk);
+		if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[low]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_low]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_low], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_low], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_low], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_low], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_low], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_low], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_low], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_low], vbios->low_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_low] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_low;
+			data->sclk_level = s_low;
+			data->required_sclk = vbios->low_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[mid]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_mid1]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid1], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid1], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid1], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid1], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_mid1], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid1], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid1], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_mid1], vbios->mid_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_mid1] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_mid;
+			data->sclk_level = s_mid1;
+			data->required_sclk = vbios->mid1_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_mid2]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_mid2]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid2], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid2], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid2], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid2], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_mid2], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid2], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid2], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_mid2], vbios->mid_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_mid2] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_mid;
+			data->sclk_level = s_mid2;
+			data->required_sclk = vbios->mid2_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_mid3]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_mid3]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid3], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid3], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid3], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid3], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_mid3], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid3], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid3], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_mid3], vbios->mid_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_mid3] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_mid;
+			data->sclk_level = s_mid3;
+			data->required_sclk = vbios->mid3_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_mid4]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_mid4]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid4], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid4], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid4], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid4], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_mid4], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid4], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid4], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_mid4], vbios->mid_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_mid4] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_mid;
+			data->sclk_level = s_mid4;
+			data->required_sclk = vbios->mid4_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_mid5]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_mid5]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid5], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid5], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid5], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid5], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_mid5], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid5], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid5], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_mid5], vbios->mid_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_mid5] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_mid;
+			data->sclk_level = s_mid5;
+			data->required_sclk = vbios->mid5_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_mid6]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_mid6]) && (data->cpup_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid6], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid6], vbios->high_voltage_max_dispclk))) && (data->cpuc_state_change_enable == bw_def_no || (bw_mtn(data->blackout_duration_margin[data->y_clk_level][s_mid6], bw_int_to_fixed(0)) && bw_ltn(data->dispclk_required_for_blackout_duration[data->y_clk_level][s_mid6], vbios->high_voltage_max_dispclk) && bw_ltn(data->dispclk_required_for_blackout_recovery[data->y_clk_level][s_mid6], vbios->high_voltage_max_dispclk))) && (!data->increase_voltage_to_support_mclk_switch || data->nbp_state_change_enable == bw_def_no || (bw_mtn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid6], bw_int_to_fixed(0)) && bw_ltn(data->min_dram_speed_change_margin[data->y_clk_level][s_mid6], bw_int_to_fixed(9999)) && bw_leq(data->dispclk_required_for_dram_speed_change[data->y_clk_level][s_mid6], vbios->high_voltage_max_dispclk) && data->num_displays_with_margin[data->y_clk_level][s_mid6] == number_of_displays_enabled_with_margin))) {
+			sclk_message = bw_def_mid;
+			data->sclk_level = s_mid6;
+			data->required_sclk = vbios->mid6_sclk;
+		}
+		else if (bw_ltn(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_high]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_high])) {
+			sclk_message = bw_def_high;
+			data->sclk_level = s_high;
+			data->required_sclk = vbios->high_sclk;
+		}
+		else if (bw_meq(data->total_average_bandwidth_no_compression, bw_mul(bw_mul(bw_frc_to_fixed(dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation, 100),sclk[s_high]),vbios->data_return_bus_width))
+				&& bw_ltn(data->required_sclk, sclk[s_high])) {
+			sclk_message = bw_def_high;
+			data->sclk_level = s_high;
+			data->required_sclk = vbios->high_sclk;
+		}
+		else {
+			sclk_message = bw_def_exceeded_allowed_maximum_sclk;
+			data->sclk_level = s_high;
+			/*required_sclk = high_sclk*/
+		}
+	}
+	/*dispclk*/
+	/*if dispclk is set to the maximum, ramping is not required.  dispclk required without ramping is less than the dispclk required with ramping.*/
+	/*if dispclk required without ramping is more than the maximum dispclk, that is the dispclk required, and the mode is not supported*/
+	/*if that does not happen, but dispclk required with ramping is more than the maximum dispclk, dispclk required is just the maximum dispclk*/
+	/*if that does not happen either, dispclk required is the dispclk required with ramping.*/
+	/*dispclk required without ramping is the maximum of the one required for display pipe pixel throughput, for scaler throughput, for total read request thrrougput and for dram/np p-state change if enabled.*/
+	/*the display pipe pixel throughput is the maximum of lines in per line out in the beginning of the frame and lines in per line out in the middle of the frame multiplied by the horizontal blank and chunk granularity factor, altogether multiplied by the ratio of the source width to the line time, divided by the line buffer pixels per dispclk throughput, and multiplied by the display pipe throughput factor.*/
+	/*the horizontal blank and chunk granularity factor is the ratio of the line time divided by the line time minus half the horizontal blank and chunk time.  it applies when the lines in per line out is not 2 or 4.*/
+	/*the dispclk required for scaler throughput is the product of the pixel rate and the scaling limits factor.*/
+	/*the dispclk required for total read request throughput is the product of the peak request-per-second bandwidth and the dispclk cycles per request, divided by the request efficiency.*/
+	/*for the dispclk required with ramping, instead of multiplying just the pipe throughput by the display pipe throughput factor, we multiply the scaler and pipe throughput by the ramping factor.*/
+	/*the scaling limits factor is the product of the horizontal scale ratio, and the ratio of the vertical taps divided by the scaler efficiency clamped to at least 1.*/
+	/*the scaling limits factor itself it also clamped to at least 1*/
+	/*if doing downscaling with the pre-downscaler enabled, the horizontal scale ratio should not be considered above (use "1")*/
+	data->downspread_factor = bw_add(bw_int_to_fixed(1), bw_div(vbios->down_spread_percentage, bw_int_to_fixed(100)));
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] == bw_def_graphics) {
+				switch (data->lb_bpc[i]) {
+				case 6:
+					data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency6_bit_per_component;
+					break;
+				case 8:
+					data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency8_bit_per_component;
+					break;
+				case 10:
+					data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency10_bit_per_component;
+					break;
+				default:
+					data->v_scaler_efficiency = dceip->graphics_vscaler_efficiency12_bit_per_component;
+					break;
+				}
+				if (data->use_alpha[i] == 1) {
+					data->v_scaler_efficiency = bw_min2(data->v_scaler_efficiency, dceip->alpha_vscaler_efficiency);
+				}
+			}
+			else {
+				switch (data->lb_bpc[i]) {
+				case 6:
+					data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency6_bit_per_component;
+					break;
+				case 8:
+					data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency8_bit_per_component;
+					break;
+				case 10:
+					data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency10_bit_per_component;
+					break;
+				default:
+					data->v_scaler_efficiency = dceip->underlay_vscaler_efficiency12_bit_per_component;
+					break;
+				}
+			}
+			if (dceip->pre_downscaler_enabled && bw_mtn(data->hsr[i], bw_int_to_fixed(1))) {
+				data->scaler_limits_factor = bw_max2(bw_div(data->v_taps[i], data->v_scaler_efficiency), bw_div(data->source_width_rounded_up_to_chunks[i], data->h_total[i]));
+			}
+			else {
+				data->scaler_limits_factor = bw_max3(bw_int_to_fixed(1), bw_ceil2(bw_div(data->h_taps[i], bw_int_to_fixed(4)), bw_int_to_fixed(1)), bw_mul(data->hsr[i], bw_max2(bw_div(data->v_taps[i], data->v_scaler_efficiency), bw_int_to_fixed(1))));
+			}
+			data->display_pipe_pixel_throughput = bw_div(bw_div(bw_mul(bw_max2(data->lb_lines_in_per_line_out_in_beginning_of_frame[i], bw_mul(data->lb_lines_in_per_line_out_in_middle_of_frame[i], data->horizontal_blank_and_chunk_granularity_factor[i])), data->source_width_rounded_up_to_chunks[i]), (bw_div(data->h_total[i], data->pixel_rate[i]))), dceip->lb_write_pixels_per_dispclk);
+			data->dispclk_required_without_ramping[i] = bw_mul(data->downspread_factor, bw_max2(bw_mul(data->pixel_rate[i], data->scaler_limits_factor), bw_mul(dceip->display_pipe_throughput_factor, data->display_pipe_pixel_throughput)));
+			data->dispclk_required_with_ramping[i] = bw_mul(dceip->dispclk_ramping_factor, bw_max2(bw_mul(data->pixel_rate[i], data->scaler_limits_factor), data->display_pipe_pixel_throughput));
+		}
+	}
+	data->total_dispclk_required_with_ramping = bw_int_to_fixed(0);
+	data->total_dispclk_required_without_ramping = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_ltn(data->total_dispclk_required_with_ramping, data->dispclk_required_with_ramping[i])) {
+				data->total_dispclk_required_with_ramping = data->dispclk_required_with_ramping[i];
+			}
+			if (bw_ltn(data->total_dispclk_required_without_ramping, data->dispclk_required_without_ramping[i])) {
+				data->total_dispclk_required_without_ramping = data->dispclk_required_without_ramping[i];
+			}
+		}
+	}
+	data->total_read_request_bandwidth = bw_int_to_fixed(0);
+	data->total_write_request_bandwidth = bw_int_to_fixed(0);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				data->total_read_request_bandwidth = bw_add(data->total_read_request_bandwidth, data->request_bandwidth[i]);
+			}
+			else {
+				data->total_write_request_bandwidth = bw_add(data->total_write_request_bandwidth, data->request_bandwidth[i]);
+			}
+		}
+	}
+	data->dispclk_required_for_total_read_request_bandwidth = bw_div(bw_mul(data->total_read_request_bandwidth, dceip->dispclk_per_request), dceip->request_efficiency);
+	data->total_dispclk_required_with_ramping_with_request_bandwidth = bw_max2(data->total_dispclk_required_with_ramping, data->dispclk_required_for_total_read_request_bandwidth);
+	data->total_dispclk_required_without_ramping_with_request_bandwidth = bw_max2(data->total_dispclk_required_without_ramping, data->dispclk_required_for_total_read_request_bandwidth);
+	if (data->cpuc_state_change_enable == bw_def_yes) {
+		data->total_dispclk_required_with_ramping_with_request_bandwidth = bw_max3(data->total_dispclk_required_with_ramping_with_request_bandwidth, data->dispclk_required_for_blackout_duration[data->y_clk_level][data->sclk_level], data->dispclk_required_for_blackout_recovery[data->y_clk_level][data->sclk_level]);
+		data->total_dispclk_required_without_ramping_with_request_bandwidth = bw_max3(data->total_dispclk_required_without_ramping_with_request_bandwidth, data->dispclk_required_for_blackout_duration[data->y_clk_level][data->sclk_level], data->dispclk_required_for_blackout_recovery[data->y_clk_level][data->sclk_level]);
+	}
+	if (data->cpup_state_change_enable == bw_def_yes) {
+		data->total_dispclk_required_with_ramping_with_request_bandwidth = bw_max2(data->total_dispclk_required_with_ramping_with_request_bandwidth, data->dispclk_required_for_blackout_duration[data->y_clk_level][data->sclk_level]);
+		data->total_dispclk_required_without_ramping_with_request_bandwidth = bw_max2(data->total_dispclk_required_without_ramping_with_request_bandwidth, data->dispclk_required_for_blackout_duration[data->y_clk_level][data->sclk_level]);
+	}
+	if (data->nbp_state_change_enable == bw_def_yes && data->increase_voltage_to_support_mclk_switch) {
+		data->total_dispclk_required_with_ramping_with_request_bandwidth = bw_max2(data->total_dispclk_required_with_ramping_with_request_bandwidth, data->dispclk_required_for_dram_speed_change[data->y_clk_level][data->sclk_level]);
+		data->total_dispclk_required_without_ramping_with_request_bandwidth = bw_max2(data->total_dispclk_required_without_ramping_with_request_bandwidth, data->dispclk_required_for_dram_speed_change[data->y_clk_level][data->sclk_level]);
+	}
+	if (bw_ltn(data->total_dispclk_required_with_ramping_with_request_bandwidth, vbios->high_voltage_max_dispclk)) {
+		data->dispclk = data->total_dispclk_required_with_ramping_with_request_bandwidth;
+	}
+	else if (bw_ltn(data->total_dispclk_required_without_ramping_with_request_bandwidth, vbios->high_voltage_max_dispclk)) {
+		data->dispclk = vbios->high_voltage_max_dispclk;
+	}
+	else {
+		data->dispclk = data->total_dispclk_required_without_ramping_with_request_bandwidth;
+	}
+	/* required core voltage*/
+	/* the core voltage required is low if sclk, yclk(pclk)and dispclk are within the low limits*/
+	/* otherwise, the core voltage required is medium if yclk (pclk) is within the low limit and sclk and dispclk are within the medium limit*/
+	/* otherwise, the core voltage required is high if the three clocks are within the high limits*/
+	/* otherwise, or if the mode is not supported, core voltage requirement is not applicable*/
+	if (pipe_check == bw_def_notok) {
+		voltage = bw_def_na;
+	}
+	else if (mode_check == bw_def_notok) {
+		voltage = bw_def_notok;
+	}
+	else if (bw_equ(bw_int_to_fixed(yclk_message), vbios->low_yclk) && sclk_message == bw_def_low && bw_ltn(data->dispclk, vbios->low_voltage_max_dispclk)) {
+		voltage = bw_def_0_72;
+	}
+	else if ((bw_equ(bw_int_to_fixed(yclk_message), vbios->low_yclk) || bw_equ(bw_int_to_fixed(yclk_message), vbios->mid_yclk)) && (sclk_message == bw_def_low || sclk_message == bw_def_mid) && bw_ltn(data->dispclk, vbios->mid_voltage_max_dispclk)) {
+		voltage = bw_def_0_8;
+	}
+	else if ((bw_equ(bw_int_to_fixed(yclk_message), vbios->low_yclk) || bw_equ(bw_int_to_fixed(yclk_message), vbios->mid_yclk) || bw_equ(bw_int_to_fixed(yclk_message), vbios->high_yclk)) && (sclk_message == bw_def_low || sclk_message == bw_def_mid || sclk_message == bw_def_high) && bw_leq(data->dispclk, vbios->high_voltage_max_dispclk)) {
+		if ((data->nbp_state_change_enable == bw_def_no && nbp_state_change_enable_blank == bw_def_no)) {
+			voltage = bw_def_high_no_nbp_state_change;
+		}
+		else {
+			voltage = bw_def_0_9;
+		}
+	}
+	else {
+		voltage = bw_def_notok;
+	}
+	if (voltage == bw_def_0_72) {
+		data->max_phyclk = vbios->low_voltage_max_phyclk;
+	}
+	else if (voltage == bw_def_0_8) {
+		data->max_phyclk = vbios->mid_voltage_max_phyclk;
+	}
+	else {
+		data->max_phyclk = vbios->high_voltage_max_phyclk;
+	}
+	/*required blackout recovery time*/
+	data->blackout_recovery_time = bw_int_to_fixed(0);
+	for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+		if (data->enable[k] && bw_mtn(vbios->blackout_duration, bw_int_to_fixed(0)) && data->cpup_state_change_enable == bw_def_yes) {
+			if (surface_type[k] != bw_def_display_write_back420_luma && surface_type[k] != bw_def_display_write_back420_chroma) {
+				data->blackout_recovery_time = bw_max2(data->blackout_recovery_time, bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[data->y_clk_level][data->sclk_level]));
+				if (bw_ltn(data->adjusted_data_buffer_size[k], bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), (bw_add(vbios->blackout_duration, bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[data->y_clk_level][data->sclk_level])))))) {
+					data->blackout_recovery_time = bw_max2(data->blackout_recovery_time, bw_div((bw_add(bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), vbios->blackout_duration), bw_sub(bw_div(bw_mul(bw_mul(bw_mul((bw_add(bw_mul(bw_int_to_fixed(2), data->total_dmifmc_urgent_latency), data->dmif_burst_time[data->y_clk_level][data->sclk_level])), data->dispclk), bw_int_to_fixed(data->bytes_per_pixel[k])), data->lines_interleaved_in_mem_access[k]), data->latency_hiding_lines[k]), data->adjusted_data_buffer_size[k]))), (bw_sub(bw_div(bw_mul(bw_mul(data->dispclk, bw_int_to_fixed(data->bytes_per_pixel[k])), data->lines_interleaved_in_mem_access[k]), data->latency_hiding_lines[k]), bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k])))));
+				}
+			}
+			else {
+				data->blackout_recovery_time = bw_max2(data->blackout_recovery_time, bw_add(bw_mul(bw_int_to_fixed(2), vbios->mcifwrmc_urgent_latency), data->mcifwr_burst_time[data->y_clk_level][data->sclk_level]));
+				if (bw_ltn(data->adjusted_data_buffer_size[k], bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), (bw_add(vbios->blackout_duration, bw_add(bw_mul(bw_int_to_fixed(2), vbios->mcifwrmc_urgent_latency), data->mcifwr_burst_time[data->y_clk_level][data->sclk_level])))))) {
+					data->blackout_recovery_time = bw_max2(data->blackout_recovery_time, bw_div((bw_add(bw_mul(bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k]), vbios->blackout_duration), bw_sub(bw_div(bw_mul(bw_mul(bw_mul((bw_add(bw_add(bw_mul(bw_int_to_fixed(2), vbios->mcifwrmc_urgent_latency), data->dmif_burst_time[data->y_clk_level][data->sclk_level]), data->mcifwr_burst_time[data->y_clk_level][data->sclk_level])), data->dispclk), bw_int_to_fixed(data->bytes_per_pixel[k])), data->lines_interleaved_in_mem_access[k]), data->latency_hiding_lines[k]), data->adjusted_data_buffer_size[k]))), (bw_sub(bw_div(bw_mul(bw_mul(data->dispclk, bw_int_to_fixed(data->bytes_per_pixel[k])), data->lines_interleaved_in_mem_access[k]), data->latency_hiding_lines[k]), bw_div(bw_mul(data->display_bandwidth[k], data->useful_bytes_per_request[k]), data->bytes_per_request[k])))));
+				}
+			}
+		}
+	}
+	/*sclk deep sleep*/
+	/*during self-refresh, sclk can be reduced to dispclk divided by the minimum pixels in the data fifo entry, with 15% margin, but shoudl not be set to less than the request bandwidth.*/
+	/*the data fifo entry is 16 pixels for the writeback, 64 bytes/bytes_per_pixel for the graphics, 16 pixels for the parallel rotation underlay,*/
+	/*and 16 bytes/bytes_per_pixel for the orthogonal rotation underlay.*/
+	/*in parallel mode (underlay pipe), the data read from the dmifv buffer is variable and based on the pixel depth (8bbp - 16 bytes, 16 bpp - 32 bytes, 32 bpp - 64 bytes)*/
+	/*in orthogonal mode (underlay pipe), the data read from the dmifv buffer is fixed at 16 bytes.*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (surface_type[i] == bw_def_display_write_back420_luma || surface_type[i] == bw_def_display_write_back420_chroma) {
+				data->pixels_per_data_fifo_entry[i] = bw_int_to_fixed(16);
+			}
+			else if (surface_type[i] == bw_def_graphics) {
+				data->pixels_per_data_fifo_entry[i] = bw_div(bw_int_to_fixed(64), bw_int_to_fixed(data->bytes_per_pixel[i]));
+			}
+			else if (data->orthogonal_rotation[i] == 0) {
+				data->pixels_per_data_fifo_entry[i] = bw_int_to_fixed(16);
+			}
+			else {
+				data->pixels_per_data_fifo_entry[i] = bw_div(bw_int_to_fixed(16), bw_int_to_fixed(data->bytes_per_pixel[i]));
+			}
+		}
+	}
+	data->min_pixels_per_data_fifo_entry = bw_int_to_fixed(9999);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_mtn(data->min_pixels_per_data_fifo_entry, data->pixels_per_data_fifo_entry[i])) {
+				data->min_pixels_per_data_fifo_entry = data->pixels_per_data_fifo_entry[i];
+			}
+		}
+	}
+	data->sclk_deep_sleep = bw_max2(bw_div(bw_mul(data->dispclk, bw_frc_to_fixed(115, 100)), data->min_pixels_per_data_fifo_entry), data->total_read_request_bandwidth);
+	/*urgent, stutter and nb-p_state watermark*/
+	/*the urgent watermark is the maximum of the urgent trip time plus the pixel transfer time, the urgent trip times to get data for the first pixel, and the urgent trip times to get data for the last pixel.*/
+	/*the stutter exit watermark is the self refresh exit time plus the maximum of the data burst time plus the pixel transfer time, the data burst times to get data for the first pixel, and the data burst times to get data for the last pixel.  it does not apply to the writeback.*/
+	/*the nb p-state change watermark is the dram speed/p-state change time plus the maximum of the data burst time plus the pixel transfer time, the data burst times to get data for the first pixel, and the data burst times to get data for the last pixel.*/
+	/*the pixel transfer time is the maximum of the time to transfer the source pixels required for the first output pixel, and the time to transfer the pixels for the last output pixel minus the active line time.*/
+	/*blackout_duration is added to the urgent watermark*/
+	data->chunk_request_time = bw_int_to_fixed(0);
+	data->cursor_request_time = bw_int_to_fixed(0);
+	/*compute total time to request one chunk from each active display pipe*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->chunk_request_time = bw_add(data->chunk_request_time, (bw_div((bw_div(bw_int_to_fixed(pixels_per_chunk * data->bytes_per_pixel[i]), data->useful_bytes_per_request[i])), bw_min2(sclk[data->sclk_level], bw_div(data->dispclk, bw_int_to_fixed(2))))));
+		}
+	}
+	/*compute total time to request cursor data*/
+	data->cursor_request_time = (bw_div(data->cursor_total_data, (bw_mul(bw_int_to_fixed(32), sclk[data->sclk_level]))));
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->line_source_pixels_transfer_time = bw_max2(bw_div(bw_div(data->src_pixels_for_first_output_pixel[i], dceip->lb_write_pixels_per_dispclk), (bw_div(data->dispclk, dceip->display_pipe_throughput_factor))), bw_sub(bw_div(bw_div(data->src_pixels_for_last_output_pixel[i], dceip->lb_write_pixels_per_dispclk), (bw_div(data->dispclk, dceip->display_pipe_throughput_factor))), data->active_time[i]));
+			if (surface_type[i] != bw_def_display_write_back420_luma && surface_type[i] != bw_def_display_write_back420_chroma) {
+				data->urgent_watermark[i] = bw_add(bw_add(bw_add(bw_add(bw_add(data->total_dmifmc_urgent_latency, data->dmif_burst_time[data->y_clk_level][data->sclk_level]), bw_max2(data->line_source_pixels_transfer_time, data->line_source_transfer_time[i][data->y_clk_level][data->sclk_level])), vbios->blackout_duration), data->chunk_request_time), data->cursor_request_time);
+				data->stutter_exit_watermark[i] = bw_add(bw_sub(vbios->stutter_self_refresh_exit_latency, data->total_dmifmc_urgent_latency), data->urgent_watermark[i]);
+				data->stutter_entry_watermark[i] = bw_add(bw_sub(bw_add(vbios->stutter_self_refresh_exit_latency, vbios->stutter_self_refresh_entry_latency), data->total_dmifmc_urgent_latency), data->urgent_watermark[i]);
+				/*unconditionally remove black out time from the nb p_state watermark*/
+				if (data->display_pstate_change_enable[i] == 1) {
+					data->nbp_state_change_watermark[i] = bw_add(bw_add(vbios->nbp_state_change_latency, data->dmif_burst_time[data->y_clk_level][data->sclk_level]), bw_max2(data->line_source_pixels_transfer_time, data->dram_speed_change_line_source_transfer_time[i][data->y_clk_level][data->sclk_level]));
+				}
+				else {
+					/*maximize the watermark to force the switch in the vb_lank region of the frame*/
+					data->nbp_state_change_watermark[i] = bw_int_to_fixed(131000);
+				}
+			}
+			else {
+				data->urgent_watermark[i] = bw_add(bw_add(bw_add(bw_add(bw_add(vbios->mcifwrmc_urgent_latency, data->mcifwr_burst_time[data->y_clk_level][data->sclk_level]), bw_max2(data->line_source_pixels_transfer_time, data->line_source_transfer_time[i][data->y_clk_level][data->sclk_level])), vbios->blackout_duration), data->chunk_request_time), data->cursor_request_time);
+				data->stutter_exit_watermark[i] = bw_int_to_fixed(0);
+				data->stutter_entry_watermark[i] = bw_int_to_fixed(0);
+				if (data->display_pstate_change_enable[i] == 1) {
+					data->nbp_state_change_watermark[i] = bw_add(bw_add(vbios->nbp_state_change_latency, data->mcifwr_burst_time[data->y_clk_level][data->sclk_level]), bw_max2(data->line_source_pixels_transfer_time, data->dram_speed_change_line_source_transfer_time[i][data->y_clk_level][data->sclk_level]));
+				}
+				else {
+					/*maximize the watermark to force the switch in the vb_lank region of the frame*/
+					data->nbp_state_change_watermark[i] = bw_int_to_fixed(131000);
+				}
+			}
+		}
+	}
+	/*stutter mode enable*/
+	/*in the multi-display case the stutter exit or entry watermark cannot exceed the minimum latency hiding capabilities of the*/
+	/*display pipe.*/
+	data->stutter_mode_enable = data->cpuc_state_change_enable;
+	if (data->number_of_displays > 1) {
+		for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+			if (data->enable[i]) {
+				if ((bw_mtn(data->stutter_exit_watermark[i], data->minimum_latency_hiding[i]) || bw_mtn(data->stutter_entry_watermark[i], data->minimum_latency_hiding[i]))) {
+					data->stutter_mode_enable = bw_def_no;
+				}
+			}
+		}
+	}
+	/*performance metrics*/
+	/* display read access efficiency (%)*/
+	/* display write back access efficiency (%)*/
+	/* stutter efficiency (%)*/
+	/* extra underlay pitch recommended for efficiency (pixels)*/
+	/* immediate flip time (us)*/
+	/* latency for other clients due to urgent display read (us)*/
+	/* latency for other clients due to urgent display write (us)*/
+	/* average bandwidth consumed by display (no compression) (gb/s)*/
+	/* required dram  bandwidth (gb/s)*/
+	/* required sclk (m_hz)*/
+	/* required rd urgent latency (us)*/
+	/* nb p-state change margin (us)*/
+	/*dmif and mcifwr dram access efficiency*/
+	/*is the ratio between the ideal dram access time (which is the data buffer size in memory divided by the dram bandwidth), and the actual time which is the total page close-open time.  but it cannot exceed the dram efficiency provided by the memory subsystem*/
+	data->dmifdram_access_efficiency = bw_min2(bw_div(bw_div(data->total_display_reads_required_dram_access_data, data->dram_bandwidth), data->dmif_total_page_close_open_time), bw_int_to_fixed(1));
+	if (bw_mtn(data->total_display_writes_required_dram_access_data, bw_int_to_fixed(0))) {
+		data->mcifwrdram_access_efficiency = bw_min2(bw_div(bw_div(data->total_display_writes_required_dram_access_data, data->dram_bandwidth), data->mcifwr_total_page_close_open_time), bw_int_to_fixed(1));
+	}
+	else {
+		data->mcifwrdram_access_efficiency = bw_int_to_fixed(0);
+	}
+	/*stutter efficiency*/
+	/*the stutter efficiency is the frame-average time in self-refresh divided by the frame-average stutter cycle duration.  only applies if the display write-back is not enabled.*/
+	/*the frame-average stutter cycle used is the minimum for all pipes of the frame-average data buffer size in time, times the compression rate*/
+	/*the frame-average time in self-refresh is the stutter cycle minus the self refresh exit latency and the burst time*/
+	/*the stutter cycle is the dmif buffer size reduced by the excess of the stutter exit watermark over the lb size in time.*/
+	/*the burst time is the data needed during the stutter cycle divided by the available bandwidth*/
+	/*compute the time read all the data from the dmif buffer to the lb (dram refresh period)*/
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->stutter_refresh_duration[i] = bw_sub(bw_mul(bw_div(bw_div(bw_mul(bw_div(bw_div(data->adjusted_data_buffer_size[i], bw_int_to_fixed(data->bytes_per_pixel[i])), data->source_width_rounded_up_to_chunks[i]), data->h_total[i]), data->vsr[i]), data->pixel_rate[i]), data->compression_rate[i]), bw_max2(bw_int_to_fixed(0), bw_sub(data->stutter_exit_watermark[i], bw_div(bw_mul((bw_sub(data->lb_partitions[i], bw_int_to_fixed(1))), data->h_total[i]), data->pixel_rate[i]))));
+			data->stutter_dmif_buffer_size[i] = bw_div(bw_mul(bw_mul(bw_div(bw_mul(bw_mul(data->stutter_refresh_duration[i], bw_int_to_fixed(data->bytes_per_pixel[i])), data->source_width_rounded_up_to_chunks[i]), data->h_total[i]), data->vsr[i]), data->pixel_rate[i]), data->compression_rate[i]);
+		}
+	}
+	data->min_stutter_refresh_duration = bw_int_to_fixed(9999);
+	data->total_stutter_dmif_buffer_size = 0;
+	data->total_bytes_requested = 0;
+	data->min_stutter_dmif_buffer_size = 9999;
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			if (bw_mtn(data->min_stutter_refresh_duration, data->stutter_refresh_duration[i])) {
+				data->min_stutter_refresh_duration = data->stutter_refresh_duration[i];
+				data->total_bytes_requested = bw_fixed_to_int(bw_add(bw_int_to_fixed(data->total_bytes_requested), (bw_mul(bw_mul(data->source_height_rounded_up_to_chunks[i], data->source_width_rounded_up_to_chunks[i]), bw_int_to_fixed(data->bytes_per_pixel[i])))));
+				data->min_stutter_dmif_buffer_size = bw_fixed_to_int(data->stutter_dmif_buffer_size[i]);
+			}
+			data->total_stutter_dmif_buffer_size = bw_fixed_to_int(bw_add(data->stutter_dmif_buffer_size[i], bw_int_to_fixed(data->total_stutter_dmif_buffer_size)));
+		}
+	}
+	data->stutter_burst_time = bw_div(bw_int_to_fixed(data->total_stutter_dmif_buffer_size), bw_mul(sclk[data->sclk_level], vbios->data_return_bus_width));
+	data->num_stutter_bursts = data->total_bytes_requested / data->min_stutter_dmif_buffer_size;
+	data->total_stutter_cycle_duration = bw_add(bw_add(data->min_stutter_refresh_duration, vbios->stutter_self_refresh_exit_latency), data->stutter_burst_time);
+	data->time_in_self_refresh = data->min_stutter_refresh_duration;
+	if (data->d1_display_write_back_dwb_enable == 1) {
+		data->stutter_efficiency = bw_int_to_fixed(0);
+	}
+	else if (bw_ltn(data->time_in_self_refresh, bw_int_to_fixed(0))) {
+		data->stutter_efficiency = bw_int_to_fixed(0);
+	}
+	else {
+		/*compute stutter efficiency assuming 60 hz refresh rate*/
+		data->stutter_efficiency = bw_max2(bw_int_to_fixed(0), bw_mul((bw_sub(bw_int_to_fixed(1), (bw_div(bw_mul((bw_add(vbios->stutter_self_refresh_exit_latency, data->stutter_burst_time)), bw_int_to_fixed(data->num_stutter_bursts)), bw_frc_to_fixed(166666667, 10000))))), bw_int_to_fixed(100)));
+	}
+	/*immediate flip time*/
+	/*if scatter gather is enabled, the immediate flip takes a number of urgent memory trips equivalent to the pte requests in a row divided by the pte request limit.*/
+	/*otherwise, it may take just one urgenr memory trip*/
+	data->worst_number_of_trips_to_memory = bw_int_to_fixed(1);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i] && data->scatter_gather_enable_for_pipe[i] == 1) {
+			data->number_of_trips_to_memory_for_getting_apte_row[i] = bw_ceil2(bw_div(data->scatter_gather_pte_requests_in_row[i], data->scatter_gather_pte_request_limit[i]), bw_int_to_fixed(1));
+			if (bw_ltn(data->worst_number_of_trips_to_memory, data->number_of_trips_to_memory_for_getting_apte_row[i])) {
+				data->worst_number_of_trips_to_memory = data->number_of_trips_to_memory_for_getting_apte_row[i];
+			}
+		}
+	}
+	data->immediate_flip_time = bw_mul(data->worst_number_of_trips_to_memory, data->total_dmifmc_urgent_latency);
+	/*worst latency for other clients*/
+	/*it is the urgent latency plus the urgent burst time*/
+	data->latency_for_non_dmif_clients = bw_add(data->total_dmifmc_urgent_latency, data->dmif_burst_time[data->y_clk_level][data->sclk_level]);
+	if (data->d1_display_write_back_dwb_enable == 1) {
+		data->latency_for_non_mcifwr_clients = bw_add(vbios->mcifwrmc_urgent_latency, dceip->mcifwr_all_surfaces_burst_time);
+	}
+	else {
+		data->latency_for_non_mcifwr_clients = bw_int_to_fixed(0);
+	}
+	/*dmif mc urgent latency supported in high sclk and yclk*/
+	data->dmifmc_urgent_latency_supported_in_high_sclk_and_yclk = bw_div((bw_sub(data->min_read_buffer_size_in_time, data->dmif_burst_time[high][s_high])), data->total_dmifmc_urgent_trips);
+	/*dram speed/p-state change margin*/
+	/*in the multi-display case the nb p-state change watermark cannot exceed the average lb size plus the dmif size or the cursor dcp buffer size*/
+	data->v_blank_nbp_state_dram_speed_change_latency_supported = bw_int_to_fixed(99999);
+	data->nbp_state_dram_speed_change_latency_supported = bw_int_to_fixed(99999);
+	for (i = 0; i <= maximum_number_of_surfaces - 1; i++) {
+		if (data->enable[i]) {
+			data->nbp_state_dram_speed_change_latency_supported = bw_min2(data->nbp_state_dram_speed_change_latency_supported, bw_add(bw_sub(data->maximum_latency_hiding_with_cursor[i], data->nbp_state_change_watermark[i]), vbios->nbp_state_change_latency));
+			data->v_blank_nbp_state_dram_speed_change_latency_supported = bw_min2(data->v_blank_nbp_state_dram_speed_change_latency_supported, bw_add(bw_sub(bw_div(bw_mul((bw_sub(data->v_total[i], bw_sub(bw_div(data->src_height[i], data->v_scale_ratio[i]), bw_int_to_fixed(4)))), data->h_total[i]), data->pixel_rate[i]), data->nbp_state_change_watermark[i]), vbios->nbp_state_change_latency));
+		}
+	}
+	/*sclk required vs urgent latency*/
+	for (i = 1; i <= 5; i++) {
+		data->display_reads_time_for_data_transfer_and_urgent_latency = bw_sub(data->min_read_buffer_size_in_time, bw_mul(data->total_dmifmc_urgent_trips, bw_int_to_fixed(i)));
+		if (pipe_check == bw_def_ok && (bw_mtn(data->display_reads_time_for_data_transfer_and_urgent_latency, data->dmif_total_page_close_open_time))) {
+			data->dmif_required_sclk_for_urgent_latency[i] = bw_div(bw_div(data->total_display_reads_required_data, data->display_reads_time_for_data_transfer_and_urgent_latency), (bw_mul(vbios->data_return_bus_width, bw_frc_to_fixed(dceip->percent_of_ideal_port_bw_received_after_urgent_latency, 100))));
+		}
+		else {
+			data->dmif_required_sclk_for_urgent_latency[i] = bw_int_to_fixed(bw_def_na);
+		}
+	}
+	/*output link bit per pixel supported*/
+	for (k = 0; k <= maximum_number_of_surfaces - 1; k++) {
+		data->output_bpphdmi[k] = bw_def_na;
+		data->output_bppdp4_lane_hbr[k] = bw_def_na;
+		data->output_bppdp4_lane_hbr2[k] = bw_def_na;
+		data->output_bppdp4_lane_hbr3[k] = bw_def_na;
+		if (data->enable[k]) {
+			data->output_bpphdmi[k] = bw_fixed_to_int(bw_mul(bw_div(bw_min2(bw_int_to_fixed(600), data->max_phyclk), data->pixel_rate[k]), bw_int_to_fixed(24)));
+			if (bw_meq(data->max_phyclk, bw_int_to_fixed(270))) {
+				data->output_bppdp4_lane_hbr[k] = bw_fixed_to_int(bw_mul(bw_div(bw_mul(bw_int_to_fixed(270), bw_int_to_fixed(4)), data->pixel_rate[k]), bw_int_to_fixed(8)));
+			}
+			if (bw_meq(data->max_phyclk, bw_int_to_fixed(540))) {
+				data->output_bppdp4_lane_hbr2[k] = bw_fixed_to_int(bw_mul(bw_div(bw_mul(bw_int_to_fixed(540), bw_int_to_fixed(4)), data->pixel_rate[k]), bw_int_to_fixed(8)));
+			}
+			if (bw_meq(data->max_phyclk, bw_int_to_fixed(810))) {
+				data->output_bppdp4_lane_hbr3[k] = bw_fixed_to_int(bw_mul(bw_div(bw_mul(bw_int_to_fixed(810), bw_int_to_fixed(4)), data->pixel_rate[k]), bw_int_to_fixed(8)));
+			}
+		}
+	}
+
+	kfree(surface_type);
+free_tiling_mode:
+	kfree(tiling_mode);
+free_yclk:
+	kfree(yclk);
+free_sclk:
+	kfree(sclk);
+}
+
+/*******************************************************************************
+ * Public functions
+ ******************************************************************************/
+void bw_calcs_init(struct bw_calcs_dceip *bw_dceip,
+	struct bw_calcs_vbios *bw_vbios,
+	struct hw_asic_id asic_id)
+{
+	struct bw_calcs_dceip *dceip;
+	struct bw_calcs_vbios *vbios;
+
+	enum bw_calcs_version version = bw_calcs_version_from_asic_id(asic_id);
+
+	dceip = kzalloc(sizeof(*dceip), GFP_KERNEL);
+	if (!dceip)
+		return;
+
+	vbios = kzalloc(sizeof(*vbios), GFP_KERNEL);
+	if (!vbios) {
+		kfree(dceip);
+		return;
+	}
+
+	dceip->version = version;
+
+	switch (version) {
+	case BW_CALCS_VERSION_CARRIZO:
+		vbios->memory_type = bw_def_gddr5;
+		vbios->dram_channel_width_in_bits = 64;
+		vbios->number_of_dram_channels = asic_id.vram_width / vbios->dram_channel_width_in_bits;
+		vbios->number_of_dram_banks = 8;
+		vbios->high_yclk = bw_int_to_fixed(1600);
+		vbios->mid_yclk = bw_int_to_fixed(1600);
+		vbios->low_yclk = bw_frc_to_fixed(66666, 100);
+		vbios->low_sclk = bw_int_to_fixed(200);
+		vbios->mid1_sclk = bw_int_to_fixed(300);
+		vbios->mid2_sclk = bw_int_to_fixed(300);
+		vbios->mid3_sclk = bw_int_to_fixed(300);
+		vbios->mid4_sclk = bw_int_to_fixed(300);
+		vbios->mid5_sclk = bw_int_to_fixed(300);
+		vbios->mid6_sclk = bw_int_to_fixed(300);
+		vbios->high_sclk = bw_frc_to_fixed(62609, 100);
+		vbios->low_voltage_max_dispclk = bw_int_to_fixed(352);
+		vbios->mid_voltage_max_dispclk = bw_int_to_fixed(467);
+		vbios->high_voltage_max_dispclk = bw_int_to_fixed(643);
+		vbios->low_voltage_max_phyclk = bw_int_to_fixed(540);
+		vbios->mid_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->high_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->data_return_bus_width = bw_int_to_fixed(32);
+		vbios->trc = bw_int_to_fixed(50);
+		vbios->dmifmc_urgent_latency = bw_int_to_fixed(4);
+		vbios->stutter_self_refresh_exit_latency = bw_frc_to_fixed(153, 10);
+		vbios->stutter_self_refresh_entry_latency = bw_int_to_fixed(0);
+		vbios->nbp_state_change_latency = bw_frc_to_fixed(19649, 1000);
+		vbios->mcifwrmc_urgent_latency = bw_int_to_fixed(10);
+		vbios->scatter_gather_enable = true;
+		vbios->down_spread_percentage = bw_frc_to_fixed(5, 10);
+		vbios->cursor_width = 32;
+		vbios->average_compression_rate = 4;
+		vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel = 256;
+		vbios->blackout_duration = bw_int_to_fixed(0); /* us */
+		vbios->maximum_blackout_recovery_time = bw_int_to_fixed(0);
+
+		dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation = 100;
+		dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation = 100;
+		dceip->percent_of_ideal_port_bw_received_after_urgent_latency = 100;
+		dceip->large_cursor = false;
+		dceip->dmif_request_buffer_size = bw_int_to_fixed(768);
+		dceip->dmif_pipe_en_fbc_chunk_tracker = false;
+		dceip->cursor_max_outstanding_group_num = 1;
+		dceip->lines_interleaved_into_lb = 2;
+		dceip->chunk_width = 256;
+		dceip->number_of_graphics_pipes = 3;
+		dceip->number_of_underlay_pipes = 1;
+		dceip->low_power_tiling_mode = 0;
+		dceip->display_write_back_supported = false;
+		dceip->argb_compression_support = false;
+		dceip->underlay_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35556, 10000);
+		dceip->underlay_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->underlay_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->underlay_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->graphics_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35, 10);
+		dceip->graphics_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->graphics_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->graphics_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->alpha_vscaler_efficiency = bw_int_to_fixed(3);
+		dceip->max_dmif_buffer_allocated = 2;
+		dceip->graphics_dmif_size = 12288;
+		dceip->underlay_luma_dmif_size = 19456;
+		dceip->underlay_chroma_dmif_size = 23552;
+		dceip->pre_downscaler_enabled = true;
+		dceip->underlay_downscale_prefetch_enabled = true;
+		dceip->lb_write_pixels_per_dispclk = bw_int_to_fixed(1);
+		dceip->lb_size_per_component444 = bw_int_to_fixed(82176);
+		dceip->graphics_lb_nodownscaling_multi_line_prefetching = false;
+		dceip->stutter_and_dram_clock_state_change_gated_before_cursor =
+			bw_int_to_fixed(0);
+		dceip->underlay420_luma_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->underlay420_chroma_lb_size_per_component =
+			bw_int_to_fixed(164352);
+		dceip->underlay422_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->cursor_chunk_width = bw_int_to_fixed(64);
+		dceip->cursor_dcp_buffer_lines = bw_int_to_fixed(4);
+		dceip->underlay_maximum_width_efficient_for_tiling =
+			bw_int_to_fixed(1920);
+		dceip->underlay_maximum_height_efficient_for_tiling =
+			bw_int_to_fixed(1080);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display =
+			bw_frc_to_fixed(3, 10);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation =
+			bw_int_to_fixed(25);
+		dceip->minimum_outstanding_pte_request_limit = bw_int_to_fixed(
+			2);
+		dceip->maximum_total_outstanding_pte_requests_allowed_by_saw =
+			bw_int_to_fixed(128);
+		dceip->limit_excessive_outstanding_dmif_requests = true;
+		dceip->linear_mode_line_request_alternation_slice =
+			bw_int_to_fixed(64);
+		dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode =
+			32;
+		dceip->display_write_back420_luma_mcifwr_buffer_size = 12288;
+		dceip->display_write_back420_chroma_mcifwr_buffer_size = 8192;
+		dceip->request_efficiency = bw_frc_to_fixed(8, 10);
+		dceip->dispclk_per_request = bw_int_to_fixed(2);
+		dceip->dispclk_ramping_factor = bw_frc_to_fixed(105, 100);
+		dceip->display_pipe_throughput_factor = bw_frc_to_fixed(105, 100);
+		dceip->scatter_gather_pte_request_rows_in_tiling_mode = 2;
+		dceip->mcifwr_all_surfaces_burst_time = bw_int_to_fixed(0); /* todo: this is a bug*/
+		break;
+	case BW_CALCS_VERSION_POLARIS10:
+		/* TODO: Treat VEGAM the same as P10 for now
+		 * Need to tune the para for VEGAM if needed */
+	case BW_CALCS_VERSION_VEGAM:
+		vbios->memory_type = bw_def_gddr5;
+		vbios->dram_channel_width_in_bits = 32;
+		vbios->number_of_dram_channels = asic_id.vram_width / vbios->dram_channel_width_in_bits;
+		vbios->number_of_dram_banks = 8;
+		vbios->high_yclk = bw_int_to_fixed(6000);
+		vbios->mid_yclk = bw_int_to_fixed(3200);
+		vbios->low_yclk = bw_int_to_fixed(1000);
+		vbios->low_sclk = bw_int_to_fixed(300);
+		vbios->mid1_sclk = bw_int_to_fixed(400);
+		vbios->mid2_sclk = bw_int_to_fixed(500);
+		vbios->mid3_sclk = bw_int_to_fixed(600);
+		vbios->mid4_sclk = bw_int_to_fixed(700);
+		vbios->mid5_sclk = bw_int_to_fixed(800);
+		vbios->mid6_sclk = bw_int_to_fixed(974);
+		vbios->high_sclk = bw_int_to_fixed(1154);
+		vbios->low_voltage_max_dispclk = bw_int_to_fixed(459);
+		vbios->mid_voltage_max_dispclk = bw_int_to_fixed(654);
+		vbios->high_voltage_max_dispclk = bw_int_to_fixed(1108);
+		vbios->low_voltage_max_phyclk = bw_int_to_fixed(540);
+		vbios->mid_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->high_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->data_return_bus_width = bw_int_to_fixed(32);
+		vbios->trc = bw_int_to_fixed(48);
+		vbios->dmifmc_urgent_latency = bw_int_to_fixed(3);
+		vbios->stutter_self_refresh_exit_latency = bw_int_to_fixed(5);
+		vbios->stutter_self_refresh_entry_latency = bw_int_to_fixed(0);
+		vbios->nbp_state_change_latency = bw_int_to_fixed(45);
+		vbios->mcifwrmc_urgent_latency = bw_int_to_fixed(10);
+		vbios->scatter_gather_enable = true;
+		vbios->down_spread_percentage = bw_frc_to_fixed(5, 10);
+		vbios->cursor_width = 32;
+		vbios->average_compression_rate = 4;
+		vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel = 256;
+		vbios->blackout_duration = bw_int_to_fixed(0); /* us */
+		vbios->maximum_blackout_recovery_time = bw_int_to_fixed(0);
+
+		dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation = 100;
+		dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation = 100;
+		dceip->percent_of_ideal_port_bw_received_after_urgent_latency = 100;
+		dceip->large_cursor = false;
+		dceip->dmif_request_buffer_size = bw_int_to_fixed(768);
+		dceip->dmif_pipe_en_fbc_chunk_tracker = false;
+		dceip->cursor_max_outstanding_group_num = 1;
+		dceip->lines_interleaved_into_lb = 2;
+		dceip->chunk_width = 256;
+		dceip->number_of_graphics_pipes = 6;
+		dceip->number_of_underlay_pipes = 0;
+		dceip->low_power_tiling_mode = 0;
+		dceip->display_write_back_supported = false;
+		dceip->argb_compression_support = true;
+		dceip->underlay_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35556, 10000);
+		dceip->underlay_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->underlay_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->underlay_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->graphics_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35, 10);
+		dceip->graphics_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->graphics_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->graphics_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->alpha_vscaler_efficiency = bw_int_to_fixed(3);
+		dceip->max_dmif_buffer_allocated = 4;
+		dceip->graphics_dmif_size = 12288;
+		dceip->underlay_luma_dmif_size = 19456;
+		dceip->underlay_chroma_dmif_size = 23552;
+		dceip->pre_downscaler_enabled = true;
+		dceip->underlay_downscale_prefetch_enabled = true;
+		dceip->lb_write_pixels_per_dispclk = bw_int_to_fixed(1);
+		dceip->lb_size_per_component444 = bw_int_to_fixed(245952);
+		dceip->graphics_lb_nodownscaling_multi_line_prefetching = true;
+		dceip->stutter_and_dram_clock_state_change_gated_before_cursor =
+			bw_int_to_fixed(1);
+		dceip->underlay420_luma_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->underlay420_chroma_lb_size_per_component =
+			bw_int_to_fixed(164352);
+		dceip->underlay422_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->cursor_chunk_width = bw_int_to_fixed(64);
+		dceip->cursor_dcp_buffer_lines = bw_int_to_fixed(4);
+		dceip->underlay_maximum_width_efficient_for_tiling =
+			bw_int_to_fixed(1920);
+		dceip->underlay_maximum_height_efficient_for_tiling =
+			bw_int_to_fixed(1080);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display =
+			bw_frc_to_fixed(3, 10);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation =
+			bw_int_to_fixed(25);
+		dceip->minimum_outstanding_pte_request_limit = bw_int_to_fixed(
+			2);
+		dceip->maximum_total_outstanding_pte_requests_allowed_by_saw =
+			bw_int_to_fixed(128);
+		dceip->limit_excessive_outstanding_dmif_requests = true;
+		dceip->linear_mode_line_request_alternation_slice =
+			bw_int_to_fixed(64);
+		dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode =
+			32;
+		dceip->display_write_back420_luma_mcifwr_buffer_size = 12288;
+		dceip->display_write_back420_chroma_mcifwr_buffer_size = 8192;
+		dceip->request_efficiency = bw_frc_to_fixed(8, 10);
+		dceip->dispclk_per_request = bw_int_to_fixed(2);
+		dceip->dispclk_ramping_factor = bw_frc_to_fixed(105, 100);
+		dceip->display_pipe_throughput_factor = bw_frc_to_fixed(105, 100);
+		dceip->scatter_gather_pte_request_rows_in_tiling_mode = 2;
+		dceip->mcifwr_all_surfaces_burst_time = bw_int_to_fixed(0);
+		break;
+	case BW_CALCS_VERSION_POLARIS11:
+		vbios->memory_type = bw_def_gddr5;
+		vbios->dram_channel_width_in_bits = 32;
+		vbios->number_of_dram_channels = asic_id.vram_width / vbios->dram_channel_width_in_bits;
+		vbios->number_of_dram_banks = 8;
+		vbios->high_yclk = bw_int_to_fixed(6000);
+		vbios->mid_yclk = bw_int_to_fixed(3200);
+		vbios->low_yclk = bw_int_to_fixed(1000);
+		vbios->low_sclk = bw_int_to_fixed(300);
+		vbios->mid1_sclk = bw_int_to_fixed(400);
+		vbios->mid2_sclk = bw_int_to_fixed(500);
+		vbios->mid3_sclk = bw_int_to_fixed(600);
+		vbios->mid4_sclk = bw_int_to_fixed(700);
+		vbios->mid5_sclk = bw_int_to_fixed(800);
+		vbios->mid6_sclk = bw_int_to_fixed(974);
+		vbios->high_sclk = bw_int_to_fixed(1154);
+		vbios->low_voltage_max_dispclk = bw_int_to_fixed(459);
+		vbios->mid_voltage_max_dispclk = bw_int_to_fixed(654);
+		vbios->high_voltage_max_dispclk = bw_int_to_fixed(1108);
+		vbios->low_voltage_max_phyclk = bw_int_to_fixed(540);
+		vbios->mid_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->high_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->data_return_bus_width = bw_int_to_fixed(32);
+		vbios->trc = bw_int_to_fixed(48);
+		if (vbios->number_of_dram_channels == 2) // 64-bit
+			vbios->dmifmc_urgent_latency = bw_int_to_fixed(4);
+		else
+			vbios->dmifmc_urgent_latency = bw_int_to_fixed(3);
+		vbios->stutter_self_refresh_exit_latency = bw_int_to_fixed(5);
+		vbios->stutter_self_refresh_entry_latency = bw_int_to_fixed(0);
+		vbios->nbp_state_change_latency = bw_int_to_fixed(45);
+		vbios->mcifwrmc_urgent_latency = bw_int_to_fixed(10);
+		vbios->scatter_gather_enable = true;
+		vbios->down_spread_percentage = bw_frc_to_fixed(5, 10);
+		vbios->cursor_width = 32;
+		vbios->average_compression_rate = 4;
+		vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel = 256;
+		vbios->blackout_duration = bw_int_to_fixed(0); /* us */
+		vbios->maximum_blackout_recovery_time = bw_int_to_fixed(0);
+
+		dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation = 100;
+		dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation = 100;
+		dceip->percent_of_ideal_port_bw_received_after_urgent_latency = 100;
+		dceip->large_cursor = false;
+		dceip->dmif_request_buffer_size = bw_int_to_fixed(768);
+		dceip->dmif_pipe_en_fbc_chunk_tracker = false;
+		dceip->cursor_max_outstanding_group_num = 1;
+		dceip->lines_interleaved_into_lb = 2;
+		dceip->chunk_width = 256;
+		dceip->number_of_graphics_pipes = 5;
+		dceip->number_of_underlay_pipes = 0;
+		dceip->low_power_tiling_mode = 0;
+		dceip->display_write_back_supported = false;
+		dceip->argb_compression_support = true;
+		dceip->underlay_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35556, 10000);
+		dceip->underlay_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->underlay_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->underlay_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->graphics_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35, 10);
+		dceip->graphics_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->graphics_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->graphics_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->alpha_vscaler_efficiency = bw_int_to_fixed(3);
+		dceip->max_dmif_buffer_allocated = 4;
+		dceip->graphics_dmif_size = 12288;
+		dceip->underlay_luma_dmif_size = 19456;
+		dceip->underlay_chroma_dmif_size = 23552;
+		dceip->pre_downscaler_enabled = true;
+		dceip->underlay_downscale_prefetch_enabled = true;
+		dceip->lb_write_pixels_per_dispclk = bw_int_to_fixed(1);
+		dceip->lb_size_per_component444 = bw_int_to_fixed(245952);
+		dceip->graphics_lb_nodownscaling_multi_line_prefetching = true;
+		dceip->stutter_and_dram_clock_state_change_gated_before_cursor =
+			bw_int_to_fixed(1);
+		dceip->underlay420_luma_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->underlay420_chroma_lb_size_per_component =
+			bw_int_to_fixed(164352);
+		dceip->underlay422_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->cursor_chunk_width = bw_int_to_fixed(64);
+		dceip->cursor_dcp_buffer_lines = bw_int_to_fixed(4);
+		dceip->underlay_maximum_width_efficient_for_tiling =
+			bw_int_to_fixed(1920);
+		dceip->underlay_maximum_height_efficient_for_tiling =
+			bw_int_to_fixed(1080);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display =
+			bw_frc_to_fixed(3, 10);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation =
+			bw_int_to_fixed(25);
+		dceip->minimum_outstanding_pte_request_limit = bw_int_to_fixed(
+			2);
+		dceip->maximum_total_outstanding_pte_requests_allowed_by_saw =
+			bw_int_to_fixed(128);
+		dceip->limit_excessive_outstanding_dmif_requests = true;
+		dceip->linear_mode_line_request_alternation_slice =
+			bw_int_to_fixed(64);
+		dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode =
+			32;
+		dceip->display_write_back420_luma_mcifwr_buffer_size = 12288;
+		dceip->display_write_back420_chroma_mcifwr_buffer_size = 8192;
+		dceip->request_efficiency = bw_frc_to_fixed(8, 10);
+		dceip->dispclk_per_request = bw_int_to_fixed(2);
+		dceip->dispclk_ramping_factor = bw_frc_to_fixed(105, 100);
+		dceip->display_pipe_throughput_factor = bw_frc_to_fixed(105, 100);
+		dceip->scatter_gather_pte_request_rows_in_tiling_mode = 2;
+		dceip->mcifwr_all_surfaces_burst_time = bw_int_to_fixed(0);
+		break;
+	case BW_CALCS_VERSION_POLARIS12:
+		vbios->memory_type = bw_def_gddr5;
+		vbios->dram_channel_width_in_bits = 32;
+		vbios->number_of_dram_channels = asic_id.vram_width / vbios->dram_channel_width_in_bits;
+		vbios->number_of_dram_banks = 8;
+		vbios->high_yclk = bw_int_to_fixed(6000);
+		vbios->mid_yclk = bw_int_to_fixed(3200);
+		vbios->low_yclk = bw_int_to_fixed(1000);
+		vbios->low_sclk = bw_int_to_fixed(678);
+		vbios->mid1_sclk = bw_int_to_fixed(864);
+		vbios->mid2_sclk = bw_int_to_fixed(900);
+		vbios->mid3_sclk = bw_int_to_fixed(920);
+		vbios->mid4_sclk = bw_int_to_fixed(940);
+		vbios->mid5_sclk = bw_int_to_fixed(960);
+		vbios->mid6_sclk = bw_int_to_fixed(980);
+		vbios->high_sclk = bw_int_to_fixed(1049);
+		vbios->low_voltage_max_dispclk = bw_int_to_fixed(459);
+		vbios->mid_voltage_max_dispclk = bw_int_to_fixed(654);
+		vbios->high_voltage_max_dispclk = bw_int_to_fixed(1108);
+		vbios->low_voltage_max_phyclk = bw_int_to_fixed(540);
+		vbios->mid_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->high_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->data_return_bus_width = bw_int_to_fixed(32);
+		vbios->trc = bw_int_to_fixed(48);
+		if (vbios->number_of_dram_channels == 2) // 64-bit
+			vbios->dmifmc_urgent_latency = bw_int_to_fixed(4);
+		else
+			vbios->dmifmc_urgent_latency = bw_int_to_fixed(3);
+		vbios->stutter_self_refresh_exit_latency = bw_int_to_fixed(5);
+		vbios->stutter_self_refresh_entry_latency = bw_int_to_fixed(0);
+		vbios->nbp_state_change_latency = bw_int_to_fixed(250);
+		vbios->mcifwrmc_urgent_latency = bw_int_to_fixed(10);
+		vbios->scatter_gather_enable = false;
+		vbios->down_spread_percentage = bw_frc_to_fixed(5, 10);
+		vbios->cursor_width = 32;
+		vbios->average_compression_rate = 4;
+		vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel = 256;
+		vbios->blackout_duration = bw_int_to_fixed(0); /* us */
+		vbios->maximum_blackout_recovery_time = bw_int_to_fixed(0);
+
+		dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation = 100;
+		dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation = 100;
+		dceip->percent_of_ideal_port_bw_received_after_urgent_latency = 100;
+		dceip->large_cursor = false;
+		dceip->dmif_request_buffer_size = bw_int_to_fixed(768);
+		dceip->dmif_pipe_en_fbc_chunk_tracker = false;
+		dceip->cursor_max_outstanding_group_num = 1;
+		dceip->lines_interleaved_into_lb = 2;
+		dceip->chunk_width = 256;
+		dceip->number_of_graphics_pipes = 5;
+		dceip->number_of_underlay_pipes = 0;
+		dceip->low_power_tiling_mode = 0;
+		dceip->display_write_back_supported = true;
+		dceip->argb_compression_support = true;
+		dceip->underlay_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35556, 10000);
+		dceip->underlay_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->underlay_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->underlay_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->graphics_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35, 10);
+		dceip->graphics_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->graphics_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->graphics_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->alpha_vscaler_efficiency = bw_int_to_fixed(3);
+		dceip->max_dmif_buffer_allocated = 4;
+		dceip->graphics_dmif_size = 12288;
+		dceip->underlay_luma_dmif_size = 19456;
+		dceip->underlay_chroma_dmif_size = 23552;
+		dceip->pre_downscaler_enabled = true;
+		dceip->underlay_downscale_prefetch_enabled = true;
+		dceip->lb_write_pixels_per_dispclk = bw_int_to_fixed(1);
+		dceip->lb_size_per_component444 = bw_int_to_fixed(245952);
+		dceip->graphics_lb_nodownscaling_multi_line_prefetching = true;
+		dceip->stutter_and_dram_clock_state_change_gated_before_cursor =
+			bw_int_to_fixed(1);
+		dceip->underlay420_luma_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->underlay420_chroma_lb_size_per_component =
+			bw_int_to_fixed(164352);
+		dceip->underlay422_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->cursor_chunk_width = bw_int_to_fixed(64);
+		dceip->cursor_dcp_buffer_lines = bw_int_to_fixed(4);
+		dceip->underlay_maximum_width_efficient_for_tiling =
+			bw_int_to_fixed(1920);
+		dceip->underlay_maximum_height_efficient_for_tiling =
+			bw_int_to_fixed(1080);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display =
+			bw_frc_to_fixed(3, 10);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation =
+			bw_int_to_fixed(25);
+		dceip->minimum_outstanding_pte_request_limit = bw_int_to_fixed(
+			2);
+		dceip->maximum_total_outstanding_pte_requests_allowed_by_saw =
+			bw_int_to_fixed(128);
+		dceip->limit_excessive_outstanding_dmif_requests = true;
+		dceip->linear_mode_line_request_alternation_slice =
+			bw_int_to_fixed(64);
+		dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode =
+			32;
+		dceip->display_write_back420_luma_mcifwr_buffer_size = 12288;
+		dceip->display_write_back420_chroma_mcifwr_buffer_size = 8192;
+		dceip->request_efficiency = bw_frc_to_fixed(8, 10);
+		dceip->dispclk_per_request = bw_int_to_fixed(2);
+		dceip->dispclk_ramping_factor = bw_frc_to_fixed(105, 100);
+		dceip->display_pipe_throughput_factor = bw_frc_to_fixed(105, 100);
+		dceip->scatter_gather_pte_request_rows_in_tiling_mode = 2;
+		dceip->mcifwr_all_surfaces_burst_time = bw_int_to_fixed(0);
+		break;
+	case BW_CALCS_VERSION_STONEY:
+		vbios->memory_type = bw_def_gddr5;
+		vbios->dram_channel_width_in_bits = 64;
+		vbios->number_of_dram_channels = asic_id.vram_width / vbios->dram_channel_width_in_bits;
+		vbios->number_of_dram_banks = 8;
+		vbios->high_yclk = bw_int_to_fixed(1866);
+		vbios->mid_yclk = bw_int_to_fixed(1866);
+		vbios->low_yclk = bw_int_to_fixed(1333);
+		vbios->low_sclk = bw_int_to_fixed(200);
+		vbios->mid1_sclk = bw_int_to_fixed(600);
+		vbios->mid2_sclk = bw_int_to_fixed(600);
+		vbios->mid3_sclk = bw_int_to_fixed(600);
+		vbios->mid4_sclk = bw_int_to_fixed(600);
+		vbios->mid5_sclk = bw_int_to_fixed(600);
+		vbios->mid6_sclk = bw_int_to_fixed(600);
+		vbios->high_sclk = bw_int_to_fixed(800);
+		vbios->low_voltage_max_dispclk = bw_int_to_fixed(352);
+		vbios->mid_voltage_max_dispclk = bw_int_to_fixed(467);
+		vbios->high_voltage_max_dispclk = bw_int_to_fixed(643);
+		vbios->low_voltage_max_phyclk = bw_int_to_fixed(540);
+		vbios->mid_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->high_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->data_return_bus_width = bw_int_to_fixed(32);
+		vbios->trc = bw_int_to_fixed(50);
+		vbios->dmifmc_urgent_latency = bw_int_to_fixed(4);
+		vbios->stutter_self_refresh_exit_latency = bw_frc_to_fixed(158, 10);
+		vbios->stutter_self_refresh_entry_latency = bw_int_to_fixed(0);
+		vbios->nbp_state_change_latency = bw_frc_to_fixed(2008, 100);
+		vbios->mcifwrmc_urgent_latency = bw_int_to_fixed(10);
+		vbios->scatter_gather_enable = true;
+		vbios->down_spread_percentage = bw_frc_to_fixed(5, 10);
+		vbios->cursor_width = 32;
+		vbios->average_compression_rate = 4;
+		vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel = 256;
+		vbios->blackout_duration = bw_int_to_fixed(0); /* us */
+		vbios->maximum_blackout_recovery_time = bw_int_to_fixed(0);
+
+		dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation = 100;
+		dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation = 100;
+		dceip->percent_of_ideal_port_bw_received_after_urgent_latency = 100;
+		dceip->large_cursor = false;
+		dceip->dmif_request_buffer_size = bw_int_to_fixed(768);
+		dceip->dmif_pipe_en_fbc_chunk_tracker = false;
+		dceip->cursor_max_outstanding_group_num = 1;
+		dceip->lines_interleaved_into_lb = 2;
+		dceip->chunk_width = 256;
+		dceip->number_of_graphics_pipes = 2;
+		dceip->number_of_underlay_pipes = 1;
+		dceip->low_power_tiling_mode = 0;
+		dceip->display_write_back_supported = false;
+		dceip->argb_compression_support = true;
+		dceip->underlay_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35556, 10000);
+		dceip->underlay_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->underlay_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->underlay_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->graphics_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35, 10);
+		dceip->graphics_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->graphics_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->graphics_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->alpha_vscaler_efficiency = bw_int_to_fixed(3);
+		dceip->max_dmif_buffer_allocated = 2;
+		dceip->graphics_dmif_size = 12288;
+		dceip->underlay_luma_dmif_size = 19456;
+		dceip->underlay_chroma_dmif_size = 23552;
+		dceip->pre_downscaler_enabled = true;
+		dceip->underlay_downscale_prefetch_enabled = true;
+		dceip->lb_write_pixels_per_dispclk = bw_int_to_fixed(1);
+		dceip->lb_size_per_component444 = bw_int_to_fixed(82176);
+		dceip->graphics_lb_nodownscaling_multi_line_prefetching = false;
+		dceip->stutter_and_dram_clock_state_change_gated_before_cursor =
+			bw_int_to_fixed(0);
+		dceip->underlay420_luma_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->underlay420_chroma_lb_size_per_component =
+			bw_int_to_fixed(164352);
+		dceip->underlay422_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->cursor_chunk_width = bw_int_to_fixed(64);
+		dceip->cursor_dcp_buffer_lines = bw_int_to_fixed(4);
+		dceip->underlay_maximum_width_efficient_for_tiling =
+			bw_int_to_fixed(1920);
+		dceip->underlay_maximum_height_efficient_for_tiling =
+			bw_int_to_fixed(1080);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display =
+			bw_frc_to_fixed(3, 10);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation =
+			bw_int_to_fixed(25);
+		dceip->minimum_outstanding_pte_request_limit = bw_int_to_fixed(
+			2);
+		dceip->maximum_total_outstanding_pte_requests_allowed_by_saw =
+			bw_int_to_fixed(128);
+		dceip->limit_excessive_outstanding_dmif_requests = true;
+		dceip->linear_mode_line_request_alternation_slice =
+			bw_int_to_fixed(64);
+		dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode =
+			32;
+		dceip->display_write_back420_luma_mcifwr_buffer_size = 12288;
+		dceip->display_write_back420_chroma_mcifwr_buffer_size = 8192;
+		dceip->request_efficiency = bw_frc_to_fixed(8, 10);
+		dceip->dispclk_per_request = bw_int_to_fixed(2);
+		dceip->dispclk_ramping_factor = bw_frc_to_fixed(105, 100);
+		dceip->display_pipe_throughput_factor = bw_frc_to_fixed(105, 100);
+		dceip->scatter_gather_pte_request_rows_in_tiling_mode = 2;
+		dceip->mcifwr_all_surfaces_burst_time = bw_int_to_fixed(0);
+		break;
+	case BW_CALCS_VERSION_VEGA10:
+		vbios->memory_type = bw_def_hbm;
+		vbios->dram_channel_width_in_bits = 128;
+		vbios->number_of_dram_channels = asic_id.vram_width / vbios->dram_channel_width_in_bits;
+		vbios->number_of_dram_banks = 16;
+		vbios->high_yclk = bw_int_to_fixed(2400);
+		vbios->mid_yclk = bw_int_to_fixed(1700);
+		vbios->low_yclk = bw_int_to_fixed(1000);
+		vbios->low_sclk = bw_int_to_fixed(300);
+		vbios->mid1_sclk = bw_int_to_fixed(350);
+		vbios->mid2_sclk = bw_int_to_fixed(400);
+		vbios->mid3_sclk = bw_int_to_fixed(500);
+		vbios->mid4_sclk = bw_int_to_fixed(600);
+		vbios->mid5_sclk = bw_int_to_fixed(700);
+		vbios->mid6_sclk = bw_int_to_fixed(760);
+		vbios->high_sclk = bw_int_to_fixed(776);
+		vbios->low_voltage_max_dispclk = bw_int_to_fixed(460);
+		vbios->mid_voltage_max_dispclk = bw_int_to_fixed(670);
+		vbios->high_voltage_max_dispclk = bw_int_to_fixed(1133);
+		vbios->low_voltage_max_phyclk = bw_int_to_fixed(540);
+		vbios->mid_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->high_voltage_max_phyclk = bw_int_to_fixed(810);
+		vbios->data_return_bus_width = bw_int_to_fixed(32);
+		vbios->trc = bw_int_to_fixed(48);
+		vbios->dmifmc_urgent_latency = bw_int_to_fixed(3);
+		vbios->stutter_self_refresh_exit_latency = bw_frc_to_fixed(75, 10);
+		vbios->stutter_self_refresh_entry_latency = bw_frc_to_fixed(19, 10);
+		vbios->nbp_state_change_latency = bw_int_to_fixed(39);
+		vbios->mcifwrmc_urgent_latency = bw_int_to_fixed(10);
+		vbios->scatter_gather_enable = false;
+		vbios->down_spread_percentage = bw_frc_to_fixed(5, 10);
+		vbios->cursor_width = 32;
+		vbios->average_compression_rate = 4;
+		vbios->number_of_request_slots_gmc_reserves_for_dmif_per_channel = 8;
+		vbios->blackout_duration = bw_int_to_fixed(0); /* us */
+		vbios->maximum_blackout_recovery_time = bw_int_to_fixed(0);
+
+		dceip->max_average_percent_of_ideal_port_bw_display_can_use_in_normal_system_operation = 100;
+		dceip->max_average_percent_of_ideal_drambw_display_can_use_in_normal_system_operation = 100;
+		dceip->percent_of_ideal_port_bw_received_after_urgent_latency = 100;
+		dceip->large_cursor = false;
+		dceip->dmif_request_buffer_size = bw_int_to_fixed(2304);
+		dceip->dmif_pipe_en_fbc_chunk_tracker = true;
+		dceip->cursor_max_outstanding_group_num = 1;
+		dceip->lines_interleaved_into_lb = 2;
+		dceip->chunk_width = 256;
+		dceip->number_of_graphics_pipes = 6;
+		dceip->number_of_underlay_pipes = 0;
+		dceip->low_power_tiling_mode = 0;
+		dceip->display_write_back_supported = true;
+		dceip->argb_compression_support = true;
+		dceip->underlay_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35556, 10000);
+		dceip->underlay_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->underlay_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->underlay_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->graphics_vscaler_efficiency6_bit_per_component =
+			bw_frc_to_fixed(35, 10);
+		dceip->graphics_vscaler_efficiency8_bit_per_component =
+			bw_frc_to_fixed(34286, 10000);
+		dceip->graphics_vscaler_efficiency10_bit_per_component =
+			bw_frc_to_fixed(32, 10);
+		dceip->graphics_vscaler_efficiency12_bit_per_component =
+			bw_int_to_fixed(3);
+		dceip->alpha_vscaler_efficiency = bw_int_to_fixed(3);
+		dceip->max_dmif_buffer_allocated = 4;
+		dceip->graphics_dmif_size = 24576;
+		dceip->underlay_luma_dmif_size = 19456;
+		dceip->underlay_chroma_dmif_size = 23552;
+		dceip->pre_downscaler_enabled = true;
+		dceip->underlay_downscale_prefetch_enabled = false;
+		dceip->lb_write_pixels_per_dispclk = bw_int_to_fixed(1);
+		dceip->lb_size_per_component444 = bw_int_to_fixed(245952);
+		dceip->graphics_lb_nodownscaling_multi_line_prefetching = true;
+		dceip->stutter_and_dram_clock_state_change_gated_before_cursor =
+			bw_int_to_fixed(1);
+		dceip->underlay420_luma_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->underlay420_chroma_lb_size_per_component =
+			bw_int_to_fixed(164352);
+		dceip->underlay422_lb_size_per_component = bw_int_to_fixed(
+			82176);
+		dceip->cursor_chunk_width = bw_int_to_fixed(64);
+		dceip->cursor_dcp_buffer_lines = bw_int_to_fixed(4);
+		dceip->underlay_maximum_width_efficient_for_tiling =
+			bw_int_to_fixed(1920);
+		dceip->underlay_maximum_height_efficient_for_tiling =
+			bw_int_to_fixed(1080);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_multiple_displays_or_single_rotated_display =
+			bw_frc_to_fixed(3, 10);
+		dceip->peak_pte_request_to_eviction_ratio_limiting_single_display_no_rotation =
+			bw_int_to_fixed(25);
+		dceip->minimum_outstanding_pte_request_limit = bw_int_to_fixed(
+			2);
+		dceip->maximum_total_outstanding_pte_requests_allowed_by_saw =
+			bw_int_to_fixed(128);
+		dceip->limit_excessive_outstanding_dmif_requests = true;
+		dceip->linear_mode_line_request_alternation_slice =
+			bw_int_to_fixed(64);
+		dceip->scatter_gather_lines_of_pte_prefetching_in_linear_mode =
+			32;
+		dceip->display_write_back420_luma_mcifwr_buffer_size = 12288;
+		dceip->display_write_back420_chroma_mcifwr_buffer_size = 8192;
+		dceip->request_efficiency = bw_frc_to_fixed(8, 10);
+		dceip->dispclk_per_request = bw_int_to_fixed(2);
+		dceip->dispclk_ramping_factor = bw_frc_to_fixed(105, 100);
+		dceip->display_pipe_throughput_factor = bw_frc_to_fixed(105, 100);
+		dceip->scatter_gather_pte_request_rows_in_tiling_mode = 2;
+		dceip->mcifwr_all_surfaces_burst_time = bw_int_to_fixed(0);
+		break;
+	default:
+		break;
+	}
+	*bw_dceip = *dceip;
+	*bw_vbios = *vbios;
+
+	kfree(dceip);
+	kfree(vbios);
+}
+
+/*
+ * Compare calculated (required) clocks against the clocks available at
+ * maximum voltage (max Performance Level).
+ */
+static bool is_display_configuration_supported(
+	const struct bw_calcs_vbios *vbios,
+	const struct dce_bw_output *calcs_output)
+{
+	uint32_t int_max_clk;
+
+	int_max_clk = bw_fixed_to_int(vbios->high_voltage_max_dispclk);
+	int_max_clk *= 1000; /* MHz to kHz */
+	if (calcs_output->dispclk_khz > int_max_clk)
+		return false;
+
+	int_max_clk = bw_fixed_to_int(vbios->high_sclk);
+	int_max_clk *= 1000; /* MHz to kHz */
+	if (calcs_output->sclk_khz > int_max_clk)
+		return false;
+
+	return true;
+}
+
+static void populate_initial_data(
+	const struct pipe_ctx pipe[], int pipe_count, struct bw_calcs_data *data)
+{
+	int i, j;
+	int num_displays = 0;
+
+	data->underlay_surface_type = bw_def_420;
+	data->panning_and_bezel_adjustment = bw_def_none;
+	data->graphics_lb_bpc = 10;
+	data->underlay_lb_bpc = 8;
+	data->underlay_tiling_mode = bw_def_tiled;
+	data->graphics_tiling_mode = bw_def_tiled;
+	data->underlay_micro_tile_mode = bw_def_display_micro_tiling;
+	data->graphics_micro_tile_mode = bw_def_display_micro_tiling;
+	data->increase_voltage_to_support_mclk_switch = true;
+
+	/* Pipes with underlay first */
+	for (i = 0; i < pipe_count; i++) {
+		if (!pipe[i].stream || !pipe[i].bottom_pipe)
+			continue;
+
+		ASSERT(pipe[i].plane_state);
+
+		if (num_displays == 0) {
+			if (!pipe[i].plane_state->visible)
+				data->d0_underlay_mode = bw_def_underlay_only;
+			else
+				data->d0_underlay_mode = bw_def_blend;
+		} else {
+			if (!pipe[i].plane_state->visible)
+				data->d1_underlay_mode = bw_def_underlay_only;
+			else
+				data->d1_underlay_mode = bw_def_blend;
+		}
+
+		data->fbc_en[num_displays + 4] = false;
+		data->lpt_en[num_displays + 4] = false;
+		data->h_total[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->timing.h_total);
+		data->v_total[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->timing.v_total);
+		data->pixel_rate[num_displays + 4] = bw_frc_to_fixed(pipe[i].stream->timing.pix_clk_100hz, 10000);
+		data->src_width[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.viewport.width);
+		data->pitch_in_pixels[num_displays + 4] = data->src_width[num_displays + 4];
+		data->src_height[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.viewport.height);
+		data->h_taps[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.taps.h_taps);
+		data->v_taps[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.taps.v_taps);
+		data->h_scale_ratio[num_displays + 4] = fixed31_32_to_bw_fixed(pipe[i].plane_res.scl_data.ratios.horz.value);
+		data->v_scale_ratio[num_displays + 4] = fixed31_32_to_bw_fixed(pipe[i].plane_res.scl_data.ratios.vert.value);
+		switch (pipe[i].plane_state->rotation) {
+		case ROTATION_ANGLE_0:
+			data->rotation_angle[num_displays + 4] = bw_int_to_fixed(0);
+			break;
+		case ROTATION_ANGLE_90:
+			data->rotation_angle[num_displays + 4] = bw_int_to_fixed(90);
+			break;
+		case ROTATION_ANGLE_180:
+			data->rotation_angle[num_displays + 4] = bw_int_to_fixed(180);
+			break;
+		case ROTATION_ANGLE_270:
+			data->rotation_angle[num_displays + 4] = bw_int_to_fixed(270);
+			break;
+		default:
+			break;
+		}
+		switch (pipe[i].plane_state->format) {
+		case SURFACE_PIXEL_FORMAT_VIDEO_420_YCbCr:
+		case SURFACE_PIXEL_FORMAT_GRPH_ARGB1555:
+		case SURFACE_PIXEL_FORMAT_GRPH_RGB565:
+			data->bytes_per_pixel[num_displays + 4] = 2;
+			break;
+		case SURFACE_PIXEL_FORMAT_GRPH_ARGB8888:
+		case SURFACE_PIXEL_FORMAT_GRPH_ABGR8888:
+		case SURFACE_PIXEL_FORMAT_GRPH_ARGB2101010:
+		case SURFACE_PIXEL_FORMAT_GRPH_ABGR2101010:
+		case SURFACE_PIXEL_FORMAT_GRPH_ABGR2101010_XR_BIAS:
+		case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCbCr:
+		case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCrCb:
+			data->bytes_per_pixel[num_displays + 4] = 4;
+			break;
+		case SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616:
+		case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616:
+		case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616F:
+			data->bytes_per_pixel[num_displays + 4] = 8;
+			break;
+		default:
+			data->bytes_per_pixel[num_displays + 4] = 4;
+			break;
+		}
+		data->interlace_mode[num_displays + 4] = false;
+		data->stereo_mode[num_displays + 4] = bw_def_mono;
+
+
+		for (j = 0; j < 2; j++) {
+			data->fbc_en[num_displays * 2 + j] = false;
+			data->lpt_en[num_displays * 2 + j] = false;
+
+			data->src_height[num_displays * 2 + j] = bw_int_to_fixed(pipe[i].bottom_pipe->plane_res.scl_data.viewport.height);
+			data->src_width[num_displays * 2 + j] = bw_int_to_fixed(pipe[i].bottom_pipe->plane_res.scl_data.viewport.width);
+			data->pitch_in_pixels[num_displays * 2 + j] = bw_int_to_fixed(
+					pipe[i].bottom_pipe->plane_state->plane_size.surface_pitch);
+			data->h_taps[num_displays * 2 + j] = bw_int_to_fixed(pipe[i].bottom_pipe->plane_res.scl_data.taps.h_taps);
+			data->v_taps[num_displays * 2 + j] = bw_int_to_fixed(pipe[i].bottom_pipe->plane_res.scl_data.taps.v_taps);
+			data->h_scale_ratio[num_displays * 2 + j] = fixed31_32_to_bw_fixed(
+					pipe[i].bottom_pipe->plane_res.scl_data.ratios.horz.value);
+			data->v_scale_ratio[num_displays * 2 + j] = fixed31_32_to_bw_fixed(
+					pipe[i].bottom_pipe->plane_res.scl_data.ratios.vert.value);
+			switch (pipe[i].bottom_pipe->plane_state->rotation) {
+			case ROTATION_ANGLE_0:
+				data->rotation_angle[num_displays * 2 + j] = bw_int_to_fixed(0);
+				break;
+			case ROTATION_ANGLE_90:
+				data->rotation_angle[num_displays * 2 + j] = bw_int_to_fixed(90);
+				break;
+			case ROTATION_ANGLE_180:
+				data->rotation_angle[num_displays * 2 + j] = bw_int_to_fixed(180);
+				break;
+			case ROTATION_ANGLE_270:
+				data->rotation_angle[num_displays * 2 + j] = bw_int_to_fixed(270);
+				break;
+			default:
+				break;
+			}
+			data->stereo_mode[num_displays * 2 + j] = bw_def_mono;
+		}
+
+		num_displays++;
+	}
+
+	/* Pipes without underlay after */
+	for (i = 0; i < pipe_count; i++) {
+		unsigned int pixel_clock_100hz;
+		if (!pipe[i].stream || pipe[i].bottom_pipe)
+			continue;
+
+
+		data->fbc_en[num_displays + 4] = false;
+		data->lpt_en[num_displays + 4] = false;
+		data->h_total[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->timing.h_total);
+		data->v_total[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->timing.v_total);
+		pixel_clock_100hz = pipe[i].stream->timing.pix_clk_100hz;
+		if (pipe[i].stream->timing.timing_3d_format == TIMING_3D_FORMAT_HW_FRAME_PACKING)
+			pixel_clock_100hz *= 2;
+		data->pixel_rate[num_displays + 4] = bw_frc_to_fixed(pixel_clock_100hz, 10000);
+		if (pipe[i].plane_state) {
+			data->src_width[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.viewport.width);
+			data->pitch_in_pixels[num_displays + 4] = data->src_width[num_displays + 4];
+			data->src_height[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.viewport.height);
+			data->h_taps[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.taps.h_taps);
+			data->v_taps[num_displays + 4] = bw_int_to_fixed(pipe[i].plane_res.scl_data.taps.v_taps);
+			data->h_scale_ratio[num_displays + 4] = fixed31_32_to_bw_fixed(pipe[i].plane_res.scl_data.ratios.horz.value);
+			data->v_scale_ratio[num_displays + 4] = fixed31_32_to_bw_fixed(pipe[i].plane_res.scl_data.ratios.vert.value);
+			switch (pipe[i].plane_state->rotation) {
+			case ROTATION_ANGLE_0:
+				data->rotation_angle[num_displays + 4] = bw_int_to_fixed(0);
+				break;
+			case ROTATION_ANGLE_90:
+				data->rotation_angle[num_displays + 4] = bw_int_to_fixed(90);
+				break;
+			case ROTATION_ANGLE_180:
+				data->rotation_angle[num_displays + 4] = bw_int_to_fixed(180);
+				break;
+			case ROTATION_ANGLE_270:
+				data->rotation_angle[num_displays + 4] = bw_int_to_fixed(270);
+				break;
+			default:
+				break;
+			}
+			switch (pipe[i].plane_state->format) {
+			case SURFACE_PIXEL_FORMAT_VIDEO_420_YCbCr:
+			case SURFACE_PIXEL_FORMAT_VIDEO_420_YCrCb:
+			case SURFACE_PIXEL_FORMAT_GRPH_ARGB1555:
+			case SURFACE_PIXEL_FORMAT_GRPH_RGB565:
+				data->bytes_per_pixel[num_displays + 4] = 2;
+				break;
+			case SURFACE_PIXEL_FORMAT_GRPH_ARGB8888:
+			case SURFACE_PIXEL_FORMAT_GRPH_ABGR8888:
+			case SURFACE_PIXEL_FORMAT_GRPH_ARGB2101010:
+			case SURFACE_PIXEL_FORMAT_GRPH_ABGR2101010:
+			case SURFACE_PIXEL_FORMAT_GRPH_ABGR2101010_XR_BIAS:
+			case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCbCr:
+			case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCrCb:
+				data->bytes_per_pixel[num_displays + 4] = 4;
+				break;
+			case SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616:
+			case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616:
+			case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616F:
+				data->bytes_per_pixel[num_displays + 4] = 8;
+				break;
+			default:
+				data->bytes_per_pixel[num_displays + 4] = 4;
+				break;
+			}
+		} else if (pipe[i].stream->dst.width != 0 &&
+					pipe[i].stream->dst.height != 0 &&
+					pipe[i].stream->src.width != 0 &&
+					pipe[i].stream->src.height != 0) {
+			data->src_width[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->src.width);
+			data->pitch_in_pixels[num_displays + 4] = data->src_width[num_displays + 4];
+			data->src_height[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->src.height);
+			data->h_taps[num_displays + 4] = pipe[i].stream->src.width == pipe[i].stream->dst.width ? bw_int_to_fixed(1) : bw_int_to_fixed(2);
+			data->v_taps[num_displays + 4] = pipe[i].stream->src.height == pipe[i].stream->dst.height ? bw_int_to_fixed(1) : bw_int_to_fixed(2);
+			data->h_scale_ratio[num_displays + 4] = bw_frc_to_fixed(pipe[i].stream->src.width, pipe[i].stream->dst.width);
+			data->v_scale_ratio[num_displays + 4] = bw_frc_to_fixed(pipe[i].stream->src.height, pipe[i].stream->dst.height);
+			data->rotation_angle[num_displays + 4] = bw_int_to_fixed(0);
+			data->bytes_per_pixel[num_displays + 4] = 4;
+		} else {
+			data->src_width[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->timing.h_addressable);
+			data->pitch_in_pixels[num_displays + 4] = data->src_width[num_displays + 4];
+			data->src_height[num_displays + 4] = bw_int_to_fixed(pipe[i].stream->timing.v_addressable);
+			data->h_taps[num_displays + 4] = bw_int_to_fixed(1);
+			data->v_taps[num_displays + 4] = bw_int_to_fixed(1);
+			data->h_scale_ratio[num_displays + 4] = bw_int_to_fixed(1);
+			data->v_scale_ratio[num_displays + 4] = bw_int_to_fixed(1);
+			data->rotation_angle[num_displays + 4] = bw_int_to_fixed(0);
+			data->bytes_per_pixel[num_displays + 4] = 4;
+		}
+
+		data->interlace_mode[num_displays + 4] = false;
+		data->stereo_mode[num_displays + 4] = bw_def_mono;
+		num_displays++;
+	}
+
+	data->number_of_displays = num_displays;
+}
+
+static bool all_displays_in_sync(const struct pipe_ctx pipe[],
+				 int pipe_count)
+{
+	const struct pipe_ctx *active_pipes[MAX_PIPES];
+	int i, num_active_pipes = 0;
+
+	for (i = 0; i < pipe_count; i++) {
+		if (!pipe[i].stream || pipe[i].top_pipe)
+			continue;
+
+		active_pipes[num_active_pipes++] = &pipe[i];
+	}
+
+	if (!num_active_pipes)
+		return false;
+
+	for (i = 1; i < num_active_pipes; ++i) {
+		if (!resource_are_streams_timing_synchronizable(
+			    active_pipes[0]->stream, active_pipes[i]->stream)) {
+			return false;
+		}
+	}
+
+	return true;
+}
+
+/*
+ * Return:
+ *	true -	Display(s) configuration supported.
+ *		In this case 'calcs_output' contains data for HW programming
+ *	false - Display(s) configuration not supported (not enough bandwidth).
+ */
+bool bw_calcs(struct dc_context *ctx,
+	const struct bw_calcs_dceip *dceip,
+	const struct bw_calcs_vbios *vbios,
+	const struct pipe_ctx pipe[],
+	int pipe_count,
+	struct dce_bw_output *calcs_output)
+{
+	struct bw_calcs_data *data = kzalloc(sizeof(struct bw_calcs_data),
+					     GFP_KERNEL);
+	if (!data)
+		return false;
+
+	populate_initial_data(pipe, pipe_count, data);
+
+	if (ctx->dc->config.multi_mon_pp_mclk_switch)
+		calcs_output->all_displays_in_sync = all_displays_in_sync(pipe, pipe_count);
+	else
+		calcs_output->all_displays_in_sync = false;
+
+	if (data->number_of_displays != 0) {
+		uint8_t yclk_lvl;
+		struct bw_fixed high_sclk = vbios->high_sclk;
+		struct bw_fixed mid1_sclk = vbios->mid1_sclk;
+		struct bw_fixed mid2_sclk = vbios->mid2_sclk;
+		struct bw_fixed mid3_sclk = vbios->mid3_sclk;
+		struct bw_fixed mid4_sclk = vbios->mid4_sclk;
+		struct bw_fixed mid5_sclk = vbios->mid5_sclk;
+		struct bw_fixed mid6_sclk = vbios->mid6_sclk;
+		struct bw_fixed low_sclk = vbios->low_sclk;
+		struct bw_fixed high_yclk = vbios->high_yclk;
+		struct bw_fixed mid_yclk = vbios->mid_yclk;
+		struct bw_fixed low_yclk = vbios->low_yclk;
+
+		if (ctx->dc->debug.bandwidth_calcs_trace) {
+			print_bw_calcs_dceip(ctx, dceip);
+			print_bw_calcs_vbios(ctx, vbios);
+			print_bw_calcs_data(ctx, data);
+		}
+		calculate_bandwidth(dceip, vbios, data);
+
+		yclk_lvl = data->y_clk_level;
+
+		calcs_output->nbp_state_change_enable =
+			data->nbp_state_change_enable;
+		calcs_output->cpuc_state_change_enable =
+				data->cpuc_state_change_enable;
+		calcs_output->cpup_state_change_enable =
+				data->cpup_state_change_enable;
+		calcs_output->stutter_mode_enable =
+				data->stutter_mode_enable;
+		calcs_output->dispclk_khz =
+			bw_fixed_to_int(bw_mul(data->dispclk,
+					bw_int_to_fixed(1000)));
+		calcs_output->blackout_recovery_time_us =
+			bw_fixed_to_int(data->blackout_recovery_time);
+		calcs_output->sclk_khz =
+			bw_fixed_to_int(bw_mul(data->required_sclk,
+					bw_int_to_fixed(1000)));
+		calcs_output->sclk_deep_sleep_khz =
+			bw_fixed_to_int(bw_mul(data->sclk_deep_sleep,
+					bw_int_to_fixed(1000)));
+		if (yclk_lvl == 0)
+			calcs_output->yclk_khz = bw_fixed_to_int(
+				bw_mul(low_yclk, bw_int_to_fixed(1000)));
+		else if (yclk_lvl == 1)
+			calcs_output->yclk_khz = bw_fixed_to_int(
+				bw_mul(mid_yclk, bw_int_to_fixed(1000)));
+		else
+			calcs_output->yclk_khz = bw_fixed_to_int(
+				bw_mul(high_yclk, bw_int_to_fixed(1000)));
+
+		/* units: nanosecond, 16bit storage. */
+
+		calcs_output->nbp_state_change_wm_ns[0].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->nbp_state_change_wm_ns[1].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->nbp_state_change_wm_ns[2].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[6], bw_int_to_fixed(1000)));
+
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->nbp_state_change_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+							nbp_state_change_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->nbp_state_change_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->nbp_state_change_wm_ns[5].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[9], bw_int_to_fixed(1000)));
+
+
+
+		calcs_output->stutter_exit_wm_ns[0].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->stutter_exit_wm_ns[1].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->stutter_exit_wm_ns[2].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->stutter_exit_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->stutter_exit_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->stutter_exit_wm_ns[5].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[9], bw_int_to_fixed(1000)));
+
+		calcs_output->stutter_entry_wm_ns[0].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->stutter_entry_wm_ns[1].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->stutter_entry_wm_ns[2].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->stutter_entry_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->stutter_entry_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->stutter_entry_wm_ns[5].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[9], bw_int_to_fixed(1000)));
+
+		calcs_output->urgent_wm_ns[0].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->urgent_wm_ns[1].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->urgent_wm_ns[2].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->urgent_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->urgent_wm_ns[3].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[4].a_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->urgent_wm_ns[5].a_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[9], bw_int_to_fixed(1000)));
+
+		if (dceip->version != BW_CALCS_VERSION_CARRIZO) {
+			((struct bw_calcs_vbios *)vbios)->low_sclk = mid3_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid1_sclk = mid3_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid2_sclk = mid3_sclk;
+			calculate_bandwidth(dceip, vbios, data);
+
+			calcs_output->nbp_state_change_wm_ns[0].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[4],bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[1].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[2].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[6], bw_int_to_fixed(1000)));
+
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->nbp_state_change_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->nbp_state_change_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->nbp_state_change_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->nbp_state_change_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->nbp_state_change_wm_ns[5].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[9], bw_int_to_fixed(1000)));
+
+
+
+			calcs_output->stutter_exit_wm_ns[0].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[4], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[1].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[2].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[6], bw_int_to_fixed(1000)));
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->stutter_exit_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->stutter_exit_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->stutter_exit_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->stutter_exit_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->stutter_exit_wm_ns[5].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[9], bw_int_to_fixed(1000)));
+
+			calcs_output->stutter_entry_wm_ns[0].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[4], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[1].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[2].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[6], bw_int_to_fixed(1000)));
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->stutter_entry_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_entry_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->stutter_entry_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_entry_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->stutter_entry_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_entry_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->stutter_entry_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_entry_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->stutter_entry_wm_ns[5].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[9], bw_int_to_fixed(1000)));
+
+			calcs_output->urgent_wm_ns[0].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[4], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[1].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[2].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[6], bw_int_to_fixed(1000)));
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->urgent_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->urgent_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->urgent_wm_ns[3].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->urgent_wm_ns[4].b_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->urgent_wm_ns[5].b_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[9], bw_int_to_fixed(1000)));
+
+			((struct bw_calcs_vbios *)vbios)->low_sclk = low_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid1_sclk = mid1_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid2_sclk = mid2_sclk;
+			((struct bw_calcs_vbios *)vbios)->low_yclk = mid_yclk;
+			calculate_bandwidth(dceip, vbios, data);
+
+			calcs_output->nbp_state_change_wm_ns[0].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[4], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[1].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[2].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[6], bw_int_to_fixed(1000)));
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->nbp_state_change_wm_ns[3].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->nbp_state_change_wm_ns[4].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->nbp_state_change_wm_ns[3].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->nbp_state_change_wm_ns[4].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						nbp_state_change_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->nbp_state_change_wm_ns[5].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[9], bw_int_to_fixed(1000)));
+
+
+			calcs_output->stutter_exit_wm_ns[0].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[4], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[1].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[2].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[6], bw_int_to_fixed(1000)));
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->stutter_exit_wm_ns[3].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->stutter_exit_wm_ns[4].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->stutter_exit_wm_ns[3].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->stutter_exit_wm_ns[4].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						stutter_exit_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->stutter_exit_wm_ns[5].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[9], bw_int_to_fixed(1000)));
+
+		calcs_output->stutter_entry_wm_ns[0].c_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->stutter_entry_wm_ns[1].c_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->stutter_entry_wm_ns[2].c_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->stutter_entry_wm_ns[3].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[4].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->stutter_entry_wm_ns[3].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[4].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->stutter_entry_wm_ns[5].c_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[9], bw_int_to_fixed(1000)));
+
+			calcs_output->urgent_wm_ns[0].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[4], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[1].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[5], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[2].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[6], bw_int_to_fixed(1000)));
+			if (ctx->dc->caps.max_slave_planes) {
+				calcs_output->urgent_wm_ns[3].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[0], bw_int_to_fixed(1000)));
+				calcs_output->urgent_wm_ns[4].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[1], bw_int_to_fixed(1000)));
+			} else {
+				calcs_output->urgent_wm_ns[3].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[7], bw_int_to_fixed(1000)));
+				calcs_output->urgent_wm_ns[4].c_mark =
+					bw_fixed_to_int(bw_mul(data->
+						urgent_watermark[8], bw_int_to_fixed(1000)));
+			}
+			calcs_output->urgent_wm_ns[5].c_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[9], bw_int_to_fixed(1000)));
+		}
+
+		if (dceip->version == BW_CALCS_VERSION_CARRIZO) {
+			((struct bw_calcs_vbios *)vbios)->low_yclk = high_yclk;
+			((struct bw_calcs_vbios *)vbios)->mid_yclk = high_yclk;
+			((struct bw_calcs_vbios *)vbios)->low_sclk = high_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid1_sclk = high_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid2_sclk = high_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid3_sclk = high_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid4_sclk = high_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid5_sclk = high_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid6_sclk = high_sclk;
+		} else {
+			((struct bw_calcs_vbios *)vbios)->low_yclk = mid_yclk;
+			((struct bw_calcs_vbios *)vbios)->low_sclk = mid3_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid1_sclk = mid3_sclk;
+			((struct bw_calcs_vbios *)vbios)->mid2_sclk = mid3_sclk;
+		}
+
+		calculate_bandwidth(dceip, vbios, data);
+
+		calcs_output->nbp_state_change_wm_ns[0].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->nbp_state_change_wm_ns[1].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->nbp_state_change_wm_ns[2].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->nbp_state_change_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->nbp_state_change_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->nbp_state_change_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					nbp_state_change_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->nbp_state_change_wm_ns[5].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				nbp_state_change_watermark[9], bw_int_to_fixed(1000)));
+
+		calcs_output->stutter_exit_wm_ns[0].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->stutter_exit_wm_ns[1].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->stutter_exit_wm_ns[2].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->stutter_exit_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->stutter_exit_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->stutter_exit_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_exit_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->stutter_exit_wm_ns[5].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_exit_watermark[9], bw_int_to_fixed(1000)));
+
+		calcs_output->stutter_entry_wm_ns[0].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->stutter_entry_wm_ns[1].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->stutter_entry_wm_ns[2].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->stutter_entry_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->stutter_entry_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->stutter_entry_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					stutter_entry_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->stutter_entry_wm_ns[5].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				stutter_entry_watermark[9], bw_int_to_fixed(1000)));
+
+		calcs_output->urgent_wm_ns[0].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[4], bw_int_to_fixed(1000)));
+		calcs_output->urgent_wm_ns[1].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[5], bw_int_to_fixed(1000)));
+		calcs_output->urgent_wm_ns[2].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[6], bw_int_to_fixed(1000)));
+		if (ctx->dc->caps.max_slave_planes) {
+			calcs_output->urgent_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[0], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[1], bw_int_to_fixed(1000)));
+		} else {
+			calcs_output->urgent_wm_ns[3].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[7], bw_int_to_fixed(1000)));
+			calcs_output->urgent_wm_ns[4].d_mark =
+				bw_fixed_to_int(bw_mul(data->
+					urgent_watermark[8], bw_int_to_fixed(1000)));
+		}
+		calcs_output->urgent_wm_ns[5].d_mark =
+			bw_fixed_to_int(bw_mul(data->
+				urgent_watermark[9], bw_int_to_fixed(1000)));
+
+		((struct bw_calcs_vbios *)vbios)->low_yclk = low_yclk;
+		((struct bw_calcs_vbios *)vbios)->mid_yclk = mid_yclk;
+		((struct bw_calcs_vbios *)vbios)->low_sclk = low_sclk;
+		((struct bw_calcs_vbios *)vbios)->mid1_sclk = mid1_sclk;
+		((struct bw_calcs_vbios *)vbios)->mid2_sclk = mid2_sclk;
+		((struct bw_calcs_vbios *)vbios)->mid3_sclk = mid3_sclk;
+		((struct bw_calcs_vbios *)vbios)->mid4_sclk = mid4_sclk;
+		((struct bw_calcs_vbios *)vbios)->mid5_sclk = mid5_sclk;
+		((struct bw_calcs_vbios *)vbios)->mid6_sclk = mid6_sclk;
+		((struct bw_calcs_vbios *)vbios)->high_sclk = high_sclk;
+	} else {
+		calcs_output->nbp_state_change_enable = true;
+		calcs_output->cpuc_state_change_enable = true;
+		calcs_output->cpup_state_change_enable = true;
+		calcs_output->stutter_mode_enable = true;
+		calcs_output->dispclk_khz = 0;
+		calcs_output->sclk_khz = 0;
+	}
+
+	kfree(data);
+
+	return is_display_configuration_supported(vbios, calcs_output);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calc_auto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calc_auto.c
@@ -0,0 +1,1933 @@
+/*
+ * Copyright 2017 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include "dm_services.h"
+#include "dcn_calc_auto.h"
+#include "dcn_calc_math.h"
+
+/*
+ * NOTE:
+ *   This file is gcc-parseable HW gospel, coming straight from HW engineers.
+ *
+ * It doesn't adhere to Linux kernel style and sometimes will do things in odd
+ * ways. Unless there is something clearly wrong with it the code should
+ * remain as-is as it provides us with a guarantee from HW that it is correct.
+ */
+
+/*REVISION#250*/
+void scaler_settings_calculation(struct dcn_bw_internal_vars *v)
+{
+	int k;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->allow_different_hratio_vratio == dcn_bw_yes) {
+			if (v->source_scan[k] == dcn_bw_hor) {
+				v->h_ratio[k] = v->viewport_width[k] / v->scaler_rec_out_width[k];
+				v->v_ratio[k] = v->viewport_height[k] / v->scaler_recout_height[k];
+			}
+			else {
+				v->h_ratio[k] = v->viewport_height[k] / v->scaler_rec_out_width[k];
+				v->v_ratio[k] = v->viewport_width[k] / v->scaler_recout_height[k];
+			}
+		}
+		else {
+			if (v->source_scan[k] == dcn_bw_hor) {
+				v->h_ratio[k] =dcn_bw_max2(v->viewport_width[k] / v->scaler_rec_out_width[k], v->viewport_height[k] / v->scaler_recout_height[k]);
+			}
+			else {
+				v->h_ratio[k] =dcn_bw_max2(v->viewport_height[k] / v->scaler_rec_out_width[k], v->viewport_width[k] / v->scaler_recout_height[k]);
+			}
+			v->v_ratio[k] = v->h_ratio[k];
+		}
+		if (v->interlace_output[k] == 1.0) {
+			v->v_ratio[k] = 2.0 * v->v_ratio[k];
+		}
+		if (v->underscan_output[k] == 1.0) {
+			v->h_ratio[k] = v->h_ratio[k] * v->under_scan_factor;
+			v->v_ratio[k] = v->v_ratio[k] * v->under_scan_factor;
+		}
+	}
+	/*scaler taps calculation*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->h_ratio[k] > 1.0) {
+			v->acceptable_quality_hta_ps =dcn_bw_min2(v->max_hscl_taps, 2.0 *dcn_bw_ceil2(v->h_ratio[k], 1.0));
+		}
+		else if (v->h_ratio[k] < 1.0) {
+			v->acceptable_quality_hta_ps = 4.0;
+		}
+		else {
+			v->acceptable_quality_hta_ps = 1.0;
+		}
+		if (v->ta_pscalculation == dcn_bw_override) {
+			v->htaps[k] = v->override_hta_ps[k];
+		}
+		else {
+			v->htaps[k] = v->acceptable_quality_hta_ps;
+		}
+		if (v->v_ratio[k] > 1.0) {
+			v->acceptable_quality_vta_ps =dcn_bw_min2(v->max_vscl_taps, 2.0 *dcn_bw_ceil2(v->v_ratio[k], 1.0));
+		}
+		else if (v->v_ratio[k] < 1.0) {
+			v->acceptable_quality_vta_ps = 4.0;
+		}
+		else {
+			v->acceptable_quality_vta_ps = 1.0;
+		}
+		if (v->ta_pscalculation == dcn_bw_override) {
+			v->vtaps[k] = v->override_vta_ps[k];
+		}
+		else {
+			v->vtaps[k] = v->acceptable_quality_vta_ps;
+		}
+		if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32 || v->source_pixel_format[k] == dcn_bw_rgb_sub_16) {
+			v->vta_pschroma[k] = 0.0;
+			v->hta_pschroma[k] = 0.0;
+		}
+		else {
+			if (v->ta_pscalculation == dcn_bw_override) {
+				v->vta_pschroma[k] = v->override_vta_pschroma[k];
+				v->hta_pschroma[k] = v->override_hta_pschroma[k];
+			}
+			else {
+				v->vta_pschroma[k] = v->acceptable_quality_vta_ps;
+				v->hta_pschroma[k] = v->acceptable_quality_hta_ps;
+			}
+		}
+	}
+}
+
+void mode_support_and_system_configuration(struct dcn_bw_internal_vars *v)
+{
+	int i;
+	int j;
+	int k;
+	/*mode support, voltage state and soc configuration*/
+
+	/*scale ratio support check*/
+
+	v->scale_ratio_support = dcn_bw_yes;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->h_ratio[k] > v->max_hscl_ratio || v->v_ratio[k] > v->max_vscl_ratio || v->h_ratio[k] > v->htaps[k] || v->v_ratio[k] > v->vtaps[k] || (v->source_pixel_format[k] != dcn_bw_rgb_sub_64 && v->source_pixel_format[k] != dcn_bw_rgb_sub_32 && v->source_pixel_format[k] != dcn_bw_rgb_sub_16 && (v->h_ratio[k] / 2.0 > v->hta_pschroma[k] || v->v_ratio[k] / 2.0 > v->vta_pschroma[k]))) {
+			v->scale_ratio_support = dcn_bw_no;
+		}
+	}
+	/*source format, pixel format and scan support check*/
+
+	v->source_format_pixel_and_scan_support = dcn_bw_yes;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if ((v->source_surface_mode[k] == dcn_bw_sw_linear && v->source_scan[k] != dcn_bw_hor) || ((v->source_surface_mode[k] == dcn_bw_sw_4_kb_d || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_x || v->source_surface_mode[k] == dcn_bw_sw_var_d || v->source_surface_mode[k] == dcn_bw_sw_var_d_x) && v->source_pixel_format[k] != dcn_bw_rgb_sub_64)) {
+			v->source_format_pixel_and_scan_support = dcn_bw_no;
+		}
+	}
+	/*bandwidth support check*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->source_scan[k] == dcn_bw_hor) {
+			v->swath_width_ysingle_dpp[k] = v->viewport_width[k];
+		}
+		else {
+			v->swath_width_ysingle_dpp[k] = v->viewport_height[k];
+		}
+		if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+			v->byte_per_pixel_in_dety[k] = 8.0;
+			v->byte_per_pixel_in_detc[k] = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_32) {
+			v->byte_per_pixel_in_dety[k] = 4.0;
+			v->byte_per_pixel_in_detc[k] = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_16) {
+			v->byte_per_pixel_in_dety[k] = 2.0;
+			v->byte_per_pixel_in_detc[k] = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+			v->byte_per_pixel_in_dety[k] = 1.0;
+			v->byte_per_pixel_in_detc[k] = 2.0;
+		}
+		else {
+			v->byte_per_pixel_in_dety[k] = 4.0f / 3.0f;
+			v->byte_per_pixel_in_detc[k] = 8.0f / 3.0f;
+		}
+	}
+	v->total_read_bandwidth_consumed_gbyte_per_second = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->read_bandwidth[k] = v->swath_width_ysingle_dpp[k] * (dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) * v->v_ratio[k] +dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 2.0 * v->v_ratio[k] / 2) / (v->htotal[k] / v->pixel_clock[k]);
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->read_bandwidth[k] = v->read_bandwidth[k] * (1 + 1 / 256);
+		}
+		if (v->pte_enable == dcn_bw_yes && v->source_scan[k] != dcn_bw_hor && (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d_x)) {
+			v->read_bandwidth[k] = v->read_bandwidth[k] * (1 + 1 / 64);
+		}
+		else if (v->pte_enable == dcn_bw_yes && v->source_scan[k] == dcn_bw_hor && (v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32) && (v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_x)) {
+			v->read_bandwidth[k] = v->read_bandwidth[k] * (1 + 1 / 256);
+		}
+		else if (v->pte_enable == dcn_bw_yes) {
+			v->read_bandwidth[k] = v->read_bandwidth[k] * (1 + 1 / 512);
+		}
+		v->total_read_bandwidth_consumed_gbyte_per_second = v->total_read_bandwidth_consumed_gbyte_per_second + v->read_bandwidth[k] / 1000.0;
+	}
+	v->total_write_bandwidth_consumed_gbyte_per_second = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->output[k] == dcn_bw_writeback && v->output_format[k] == dcn_bw_444) {
+			v->write_bandwidth[k] = v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) * 4.0;
+		}
+		else if (v->output[k] == dcn_bw_writeback) {
+			v->write_bandwidth[k] = v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) * 1.5;
+		}
+		else {
+			v->write_bandwidth[k] = 0.0;
+		}
+		v->total_write_bandwidth_consumed_gbyte_per_second = v->total_write_bandwidth_consumed_gbyte_per_second + v->write_bandwidth[k] / 1000.0;
+	}
+	v->total_bandwidth_consumed_gbyte_per_second = v->total_read_bandwidth_consumed_gbyte_per_second + v->total_write_bandwidth_consumed_gbyte_per_second;
+	v->dcc_enabled_in_any_plane = dcn_bw_no;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->dcc_enabled_in_any_plane = dcn_bw_yes;
+		}
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		v->return_bw_todcn_per_state =dcn_bw_min2(v->return_bus_width * v->dcfclk_per_state[i], v->fabric_and_dram_bandwidth_per_state[i] * 1000.0 * v->percent_of_ideal_drambw_received_after_urg_latency / 100.0);
+		v->return_bw_per_state[i] = v->return_bw_todcn_per_state;
+		if (v->dcc_enabled_in_any_plane == dcn_bw_yes && v->return_bw_todcn_per_state > v->dcfclk_per_state[i] * v->return_bus_width / 4.0) {
+			v->return_bw_per_state[i] =dcn_bw_min2(v->return_bw_per_state[i], v->return_bw_todcn_per_state * 4.0 * (1.0 - v->urgent_latency / ((v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 / (v->return_bw_todcn_per_state - v->dcfclk_per_state[i] * v->return_bus_width / 4.0) + v->urgent_latency)));
+		}
+		v->critical_point = 2.0 * v->return_bus_width * v->dcfclk_per_state[i] * v->urgent_latency / (v->return_bw_todcn_per_state * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0);
+		if (v->dcc_enabled_in_any_plane == dcn_bw_yes && v->critical_point > 1.0 && v->critical_point < 4.0) {
+			v->return_bw_per_state[i] =dcn_bw_min2(v->return_bw_per_state[i], dcn_bw_pow(4.0 * v->return_bw_todcn_per_state * (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 * v->return_bus_width * v->dcfclk_per_state[i] * v->urgent_latency / (v->return_bw_todcn_per_state * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0), 2));
+		}
+		v->return_bw_todcn_per_state =dcn_bw_min2(v->return_bus_width * v->dcfclk_per_state[i], v->fabric_and_dram_bandwidth_per_state[i] * 1000.0);
+		if (v->dcc_enabled_in_any_plane == dcn_bw_yes && v->return_bw_todcn_per_state > v->dcfclk_per_state[i] * v->return_bus_width / 4.0) {
+			v->return_bw_per_state[i] =dcn_bw_min2(v->return_bw_per_state[i], v->return_bw_todcn_per_state * 4.0 * (1.0 - v->urgent_latency / ((v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 / (v->return_bw_todcn_per_state - v->dcfclk_per_state[i] * v->return_bus_width / 4.0) + v->urgent_latency)));
+		}
+		v->critical_point = 2.0 * v->return_bus_width * v->dcfclk_per_state[i] * v->urgent_latency / (v->return_bw_todcn_per_state * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0);
+		if (v->dcc_enabled_in_any_plane == dcn_bw_yes && v->critical_point > 1.0 && v->critical_point < 4.0) {
+			v->return_bw_per_state[i] =dcn_bw_min2(v->return_bw_per_state[i], dcn_bw_pow(4.0 * v->return_bw_todcn_per_state * (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 * v->return_bus_width * v->dcfclk_per_state[i] * v->urgent_latency / (v->return_bw_todcn_per_state * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0), 2));
+		}
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		if ((v->total_read_bandwidth_consumed_gbyte_per_second * 1000.0 <= v->return_bw_per_state[i]) && (v->total_bandwidth_consumed_gbyte_per_second * 1000.0 <= v->fabric_and_dram_bandwidth_per_state[i] * 1000.0 * v->percent_of_ideal_drambw_received_after_urg_latency / 100.0)) {
+			v->bandwidth_support[i] = dcn_bw_yes;
+		}
+		else {
+			v->bandwidth_support[i] = dcn_bw_no;
+		}
+	}
+	/*writeback latency support check*/
+
+	v->writeback_latency_support = dcn_bw_yes;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->output[k] == dcn_bw_writeback && v->output_format[k] == dcn_bw_444 && v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) * 4.0 > (v->writeback_luma_buffer_size + v->writeback_chroma_buffer_size) * 1024.0 / v->write_back_latency) {
+			v->writeback_latency_support = dcn_bw_no;
+		}
+		else if (v->output[k] == dcn_bw_writeback && v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) >dcn_bw_min2(v->writeback_luma_buffer_size, 2.0 * v->writeback_chroma_buffer_size) * 1024.0 / v->write_back_latency) {
+			v->writeback_latency_support = dcn_bw_no;
+		}
+	}
+	/*re-ordering buffer support check*/
+
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		v->urgent_round_trip_and_out_of_order_latency_per_state[i] = (v->round_trip_ping_latency_cycles + 32.0) / v->dcfclk_per_state[i] + v->urgent_out_of_order_return_per_channel * v->number_of_channels / v->return_bw_per_state[i];
+		if ((v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 / v->return_bw_per_state[i] > v->urgent_round_trip_and_out_of_order_latency_per_state[i]) {
+			v->rob_support[i] = dcn_bw_yes;
+		}
+		else {
+			v->rob_support[i] = dcn_bw_no;
+		}
+	}
+	/*display io support check*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->output[k] == dcn_bw_dp && v->dsc_capability == dcn_bw_yes) {
+			if (v->output_format[k] == dcn_bw_420) {
+				v->required_output_bw = v->pixel_clock[k] / 2.0;
+			}
+			else {
+				v->required_output_bw = v->pixel_clock[k];
+			}
+		}
+		else if (v->output_format[k] == dcn_bw_420) {
+			v->required_output_bw = v->pixel_clock[k] * 3.0 / 2.0;
+		}
+		else {
+			v->required_output_bw = v->pixel_clock[k] * 3.0;
+		}
+		if (v->output[k] == dcn_bw_hdmi) {
+			v->required_phyclk[k] = v->required_output_bw;
+			switch (v->output_deep_color[k]) {
+			case dcn_bw_encoder_10bpc:
+				v->required_phyclk[k] =  v->required_phyclk[k] * 5.0 / 4;
+			break;
+			case dcn_bw_encoder_12bpc:
+				v->required_phyclk[k] =  v->required_phyclk[k] * 3.0 / 2;
+				break;
+			default:
+				break;
+			}
+			v->required_phyclk[k] = v->required_phyclk[k] / 3.0;
+		}
+		else if (v->output[k] == dcn_bw_dp) {
+			v->required_phyclk[k] = v->required_output_bw / 4.0;
+		}
+		else {
+			v->required_phyclk[k] = 0.0;
+		}
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		v->dio_support[i] = dcn_bw_yes;
+		for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+			if (v->required_phyclk[k] > v->phyclk_per_state[i] || (v->output[k] == dcn_bw_hdmi && v->required_phyclk[k] > 600.0)) {
+				v->dio_support[i] = dcn_bw_no;
+			}
+		}
+	}
+	/*total available writeback support check*/
+
+	v->total_number_of_active_writeback = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->output[k] == dcn_bw_writeback) {
+			v->total_number_of_active_writeback = v->total_number_of_active_writeback + 1.0;
+		}
+	}
+	if (v->total_number_of_active_writeback <= v->max_num_writeback) {
+		v->total_available_writeback_support = dcn_bw_yes;
+	}
+	else {
+		v->total_available_writeback_support = dcn_bw_no;
+	}
+	/*maximum dispclk/dppclk support check*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->h_ratio[k] > 1.0) {
+			v->pscl_factor[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput * v->h_ratio[k] /dcn_bw_ceil2(v->htaps[k] / 6.0, 1.0));
+		}
+		else {
+			v->pscl_factor[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput);
+		}
+		if (v->byte_per_pixel_in_detc[k] == 0.0) {
+			v->pscl_factor_chroma[k] = 0.0;
+			v->min_dppclk_using_single_dpp[k] = v->pixel_clock[k] *dcn_bw_max3(v->vtaps[k] / 6.0 *dcn_bw_min2(1.0, v->h_ratio[k]), v->h_ratio[k] * v->v_ratio[k] / v->pscl_factor[k], 1.0);
+		}
+		else {
+			if (v->h_ratio[k] / 2.0 > 1.0) {
+				v->pscl_factor_chroma[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput * v->h_ratio[k] / 2.0 /dcn_bw_ceil2(v->hta_pschroma[k] / 6.0, 1.0));
+			}
+			else {
+				v->pscl_factor_chroma[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput);
+			}
+			v->min_dppclk_using_single_dpp[k] = v->pixel_clock[k] *dcn_bw_max5(v->vtaps[k] / 6.0 *dcn_bw_min2(1.0, v->h_ratio[k]), v->h_ratio[k] * v->v_ratio[k] / v->pscl_factor[k], v->vta_pschroma[k] / 6.0 *dcn_bw_min2(1.0, v->h_ratio[k] / 2.0), v->h_ratio[k] * v->v_ratio[k] / 4.0 / v->pscl_factor_chroma[k], 1.0);
+		}
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if ((v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32 || v->source_pixel_format[k] == dcn_bw_rgb_sub_16)) {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->read256_block_height_y[k] = 1.0;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+				v->read256_block_height_y[k] = 4.0;
+			}
+			else {
+				v->read256_block_height_y[k] = 8.0;
+			}
+			v->read256_block_width_y[k] = 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / v->read256_block_height_y[k];
+			v->read256_block_height_c[k] = 0.0;
+			v->read256_block_width_c[k] = 0.0;
+		}
+		else {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->read256_block_height_y[k] = 1.0;
+				v->read256_block_height_c[k] = 1.0;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+				v->read256_block_height_y[k] = 16.0;
+				v->read256_block_height_c[k] = 8.0;
+			}
+			else {
+				v->read256_block_height_y[k] = 8.0;
+				v->read256_block_height_c[k] = 8.0;
+			}
+			v->read256_block_width_y[k] = 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / v->read256_block_height_y[k];
+			v->read256_block_width_c[k] = 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / v->read256_block_height_c[k];
+		}
+		if (v->source_scan[k] == dcn_bw_hor) {
+			v->max_swath_height_y[k] = v->read256_block_height_y[k];
+			v->max_swath_height_c[k] = v->read256_block_height_c[k];
+		}
+		else {
+			v->max_swath_height_y[k] = v->read256_block_width_y[k];
+			v->max_swath_height_c[k] = v->read256_block_width_c[k];
+		}
+		if ((v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32 || v->source_pixel_format[k] == dcn_bw_rgb_sub_16)) {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear || (v->source_pixel_format[k] == dcn_bw_rgb_sub_64 && (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_var_s || v->source_surface_mode[k] == dcn_bw_sw_var_s_x) && v->source_scan[k] == dcn_bw_hor)) {
+				v->min_swath_height_y[k] = v->max_swath_height_y[k];
+			}
+			else {
+				v->min_swath_height_y[k] = v->max_swath_height_y[k] / 2.0;
+			}
+			v->min_swath_height_c[k] = v->max_swath_height_c[k];
+		}
+		else {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->min_swath_height_y[k] = v->max_swath_height_y[k];
+				v->min_swath_height_c[k] = v->max_swath_height_c[k];
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8 && v->source_scan[k] == dcn_bw_hor) {
+				v->min_swath_height_y[k] = v->max_swath_height_y[k] / 2.0;
+				if (v->bug_forcing_luma_and_chroma_request_to_same_size_fixed == dcn_bw_yes) {
+					v->min_swath_height_c[k] = v->max_swath_height_c[k];
+				}
+				else {
+					v->min_swath_height_c[k] = v->max_swath_height_c[k] / 2.0;
+				}
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_10 && v->source_scan[k] == dcn_bw_hor) {
+				v->min_swath_height_c[k] = v->max_swath_height_c[k] / 2.0;
+				if (v->bug_forcing_luma_and_chroma_request_to_same_size_fixed == dcn_bw_yes) {
+					v->min_swath_height_y[k] = v->max_swath_height_y[k];
+				}
+				else {
+					v->min_swath_height_y[k] = v->max_swath_height_y[k] / 2.0;
+				}
+			}
+			else {
+				v->min_swath_height_y[k] = v->max_swath_height_y[k];
+				v->min_swath_height_c[k] = v->max_swath_height_c[k];
+			}
+		}
+		if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+			v->maximum_swath_width = 8192.0;
+		}
+		else {
+			v->maximum_swath_width = 5120.0;
+		}
+		v->number_of_dpp_required_for_det_size =dcn_bw_ceil2(v->swath_width_ysingle_dpp[k] /dcn_bw_min2(v->maximum_swath_width, v->det_buffer_size_in_kbyte * 1024.0 / 2.0 / (v->byte_per_pixel_in_dety[k] * v->min_swath_height_y[k] + v->byte_per_pixel_in_detc[k] / 2.0 * v->min_swath_height_c[k])), 1.0);
+		if (v->byte_per_pixel_in_detc[k] == 0.0) {
+			v->number_of_dpp_required_for_lb_size =dcn_bw_ceil2((v->vtaps[k] +dcn_bw_max2(dcn_bw_ceil2(v->v_ratio[k], 1.0) - 2, 0.0)) * v->swath_width_ysingle_dpp[k] /dcn_bw_max2(v->h_ratio[k], 1.0) * v->lb_bit_per_pixel[k] / v->line_buffer_size, 1.0);
+		}
+		else {
+			v->number_of_dpp_required_for_lb_size =dcn_bw_max2(dcn_bw_ceil2((v->vtaps[k] +dcn_bw_max2(dcn_bw_ceil2(v->v_ratio[k], 1.0) - 2, 0.0)) * v->swath_width_ysingle_dpp[k] /dcn_bw_max2(v->h_ratio[k], 1.0) * v->lb_bit_per_pixel[k] / v->line_buffer_size, 1.0),dcn_bw_ceil2((v->vta_pschroma[k] +dcn_bw_max2(dcn_bw_ceil2(v->v_ratio[k] / 2.0, 1.0) - 2, 0.0)) * v->swath_width_ysingle_dpp[k] / 2.0 /dcn_bw_max2(v->h_ratio[k] / 2.0, 1.0) * v->lb_bit_per_pixel[k] / v->line_buffer_size, 1.0));
+		}
+		v->number_of_dpp_required_for_det_and_lb_size[k] =dcn_bw_max2(v->number_of_dpp_required_for_det_size, v->number_of_dpp_required_for_lb_size);
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		for (j = 0; j <= 1; j++) {
+			v->total_number_of_active_dpp[i][j] = 0.0;
+			v->required_dispclk[i][j] = 0.0;
+			v->dispclk_dppclk_support[i][j] = dcn_bw_yes;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->min_dispclk_using_single_dpp =dcn_bw_max2(v->pixel_clock[k], v->min_dppclk_using_single_dpp[k] * (j + 1)) * (1.0 + v->downspreading / 100.0);
+				if (v->odm_capability == dcn_bw_yes) {
+					v->min_dispclk_using_dual_dpp =dcn_bw_max2(v->pixel_clock[k] / 2.0, v->min_dppclk_using_single_dpp[k] / 2.0 * (j + 1)) * (1.0 + v->downspreading / 100.0);
+				}
+				else {
+					v->min_dispclk_using_dual_dpp =dcn_bw_max2(v->pixel_clock[k], v->min_dppclk_using_single_dpp[k] / 2.0 * (j + 1)) * (1.0 + v->downspreading / 100.0);
+				}
+				if (i < number_of_states) {
+					v->min_dispclk_using_single_dpp = v->min_dispclk_using_single_dpp * (1.0 + v->dispclk_ramping_margin / 100.0);
+					v->min_dispclk_using_dual_dpp = v->min_dispclk_using_dual_dpp * (1.0 + v->dispclk_ramping_margin / 100.0);
+				}
+				if (v->min_dispclk_using_single_dpp <=dcn_bw_min2(v->max_dispclk[i], (j + 1) * v->max_dppclk[i]) && v->number_of_dpp_required_for_det_and_lb_size[k] <= 1.0) {
+					v->no_of_dpp[i][j][k] = 1.0;
+					v->required_dispclk[i][j] =dcn_bw_max2(v->required_dispclk[i][j], v->min_dispclk_using_single_dpp);
+				}
+				else if (v->min_dispclk_using_dual_dpp <=dcn_bw_min2(v->max_dispclk[i], (j + 1) * v->max_dppclk[i])) {
+					v->no_of_dpp[i][j][k] = 2.0;
+					v->required_dispclk[i][j] =dcn_bw_max2(v->required_dispclk[i][j], v->min_dispclk_using_dual_dpp);
+				}
+				else {
+					v->no_of_dpp[i][j][k] = 2.0;
+					v->required_dispclk[i][j] =dcn_bw_max2(v->required_dispclk[i][j], v->min_dispclk_using_dual_dpp);
+					v->dispclk_dppclk_support[i][j] = dcn_bw_no;
+				}
+				v->total_number_of_active_dpp[i][j] = v->total_number_of_active_dpp[i][j] + v->no_of_dpp[i][j][k];
+			}
+			if (v->total_number_of_active_dpp[i][j] > v->max_num_dpp) {
+				v->total_number_of_active_dpp[i][j] = 0.0;
+				v->required_dispclk[i][j] = 0.0;
+				v->dispclk_dppclk_support[i][j] = dcn_bw_yes;
+				for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+					v->min_dispclk_using_single_dpp =dcn_bw_max2(v->pixel_clock[k], v->min_dppclk_using_single_dpp[k] * (j + 1)) * (1.0 + v->downspreading / 100.0);
+					v->min_dispclk_using_dual_dpp =dcn_bw_max2(v->pixel_clock[k], v->min_dppclk_using_single_dpp[k] / 2.0 * (j + 1)) * (1.0 + v->downspreading / 100.0);
+					if (i < number_of_states) {
+						v->min_dispclk_using_single_dpp = v->min_dispclk_using_single_dpp * (1.0 + v->dispclk_ramping_margin / 100.0);
+						v->min_dispclk_using_dual_dpp = v->min_dispclk_using_dual_dpp * (1.0 + v->dispclk_ramping_margin / 100.0);
+					}
+					if (v->number_of_dpp_required_for_det_and_lb_size[k] <= 1.0) {
+						v->no_of_dpp[i][j][k] = 1.0;
+						v->required_dispclk[i][j] =dcn_bw_max2(v->required_dispclk[i][j], v->min_dispclk_using_single_dpp);
+						if (v->min_dispclk_using_single_dpp >dcn_bw_min2(v->max_dispclk[i], (j + 1) * v->max_dppclk[i])) {
+							v->dispclk_dppclk_support[i][j] = dcn_bw_no;
+						}
+					}
+					else {
+						v->no_of_dpp[i][j][k] = 2.0;
+						v->required_dispclk[i][j] =dcn_bw_max2(v->required_dispclk[i][j], v->min_dispclk_using_dual_dpp);
+						if (v->min_dispclk_using_dual_dpp >dcn_bw_min2(v->max_dispclk[i], (j + 1) * v->max_dppclk[i])) {
+							v->dispclk_dppclk_support[i][j] = dcn_bw_no;
+						}
+					}
+					v->total_number_of_active_dpp[i][j] = v->total_number_of_active_dpp[i][j] + v->no_of_dpp[i][j][k];
+				}
+			}
+		}
+	}
+	/*viewport size check*/
+
+	v->viewport_size_support = dcn_bw_yes;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->number_of_dpp_required_for_det_and_lb_size[k] > 2.0) {
+			v->viewport_size_support = dcn_bw_no;
+		}
+	}
+	/*total available pipes support check*/
+
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		for (j = 0; j <= 1; j++) {
+			if (v->total_number_of_active_dpp[i][j] <= v->max_num_dpp) {
+				v->total_available_pipes_support[i][j] = dcn_bw_yes;
+			}
+			else {
+				v->total_available_pipes_support[i][j] = dcn_bw_no;
+			}
+		}
+	}
+	/*urgent latency support check*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		for (i = 0; i <= number_of_states_plus_one; i++) {
+			for (j = 0; j <= 1; j++) {
+				v->swath_width_yper_state[i][j][k] = v->swath_width_ysingle_dpp[k] / v->no_of_dpp[i][j][k];
+				v->swath_width_granularity_y = 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / v->max_swath_height_y[k];
+				v->rounded_up_max_swath_size_bytes_y = (dcn_bw_ceil2(v->swath_width_yper_state[i][j][k] - 1.0, v->swath_width_granularity_y) + v->swath_width_granularity_y) * v->byte_per_pixel_in_dety[k] * v->max_swath_height_y[k];
+				if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_10) {
+					v->rounded_up_max_swath_size_bytes_y =dcn_bw_ceil2(v->rounded_up_max_swath_size_bytes_y, 256.0) + 256;
+				}
+				if (v->max_swath_height_c[k] > 0.0) {
+					v->swath_width_granularity_c = 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / v->max_swath_height_c[k];
+				}
+				v->rounded_up_max_swath_size_bytes_c = (dcn_bw_ceil2(v->swath_width_yper_state[i][j][k] / 2.0 - 1.0, v->swath_width_granularity_c) + v->swath_width_granularity_c) * v->byte_per_pixel_in_detc[k] * v->max_swath_height_c[k];
+				if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_10) {
+					v->rounded_up_max_swath_size_bytes_c =dcn_bw_ceil2(v->rounded_up_max_swath_size_bytes_c, 256.0) + 256;
+				}
+				if (v->rounded_up_max_swath_size_bytes_y + v->rounded_up_max_swath_size_bytes_c <= v->det_buffer_size_in_kbyte * 1024.0 / 2.0) {
+					v->swath_height_yper_state[i][j][k] = v->max_swath_height_y[k];
+					v->swath_height_cper_state[i][j][k] = v->max_swath_height_c[k];
+				}
+				else {
+					v->swath_height_yper_state[i][j][k] = v->min_swath_height_y[k];
+					v->swath_height_cper_state[i][j][k] = v->min_swath_height_c[k];
+				}
+				if (v->byte_per_pixel_in_detc[k] == 0.0) {
+					v->lines_in_det_luma = v->det_buffer_size_in_kbyte * 1024.0 / v->byte_per_pixel_in_dety[k] / v->swath_width_yper_state[i][j][k];
+					v->lines_in_det_chroma = 0.0;
+				}
+				else if (v->swath_height_yper_state[i][j][k] <= v->swath_height_cper_state[i][j][k]) {
+					v->lines_in_det_luma = v->det_buffer_size_in_kbyte * 1024.0 / 2.0 / v->byte_per_pixel_in_dety[k] / v->swath_width_yper_state[i][j][k];
+					v->lines_in_det_chroma = v->det_buffer_size_in_kbyte * 1024.0 / 2.0 / v->byte_per_pixel_in_detc[k] / (v->swath_width_yper_state[i][j][k] / 2.0);
+				}
+				else {
+					v->lines_in_det_luma = v->det_buffer_size_in_kbyte * 1024.0 * 2.0 / 3.0 / v->byte_per_pixel_in_dety[k] / v->swath_width_yper_state[i][j][k];
+					v->lines_in_det_chroma = v->det_buffer_size_in_kbyte * 1024.0 / 3.0 / v->byte_per_pixel_in_dety[k] / (v->swath_width_yper_state[i][j][k] / 2.0);
+				}
+				v->effective_lb_latency_hiding_source_lines_luma =dcn_bw_min2(v->max_line_buffer_lines,dcn_bw_floor2(v->line_buffer_size / v->lb_bit_per_pixel[k] / (v->swath_width_yper_state[i][j][k] /dcn_bw_max2(v->h_ratio[k], 1.0)), 1.0)) - (v->vtaps[k] - 1.0);
+				v->effective_lb_latency_hiding_source_lines_chroma =dcn_bw_min2(v->max_line_buffer_lines,dcn_bw_floor2(v->line_buffer_size / v->lb_bit_per_pixel[k] / (v->swath_width_yper_state[i][j][k] / 2.0 /dcn_bw_max2(v->h_ratio[k] / 2.0, 1.0)), 1.0)) - (v->vta_pschroma[k] - 1.0);
+				v->effective_detlb_lines_luma =dcn_bw_floor2(v->lines_in_det_luma +dcn_bw_min2(v->lines_in_det_luma * v->required_dispclk[i][j] * v->byte_per_pixel_in_dety[k] * v->pscl_factor[k] / v->return_bw_per_state[i], v->effective_lb_latency_hiding_source_lines_luma), v->swath_height_yper_state[i][j][k]);
+				v->effective_detlb_lines_chroma =dcn_bw_floor2(v->lines_in_det_chroma +dcn_bw_min2(v->lines_in_det_chroma * v->required_dispclk[i][j] * v->byte_per_pixel_in_detc[k] * v->pscl_factor_chroma[k] / v->return_bw_per_state[i], v->effective_lb_latency_hiding_source_lines_chroma), v->swath_height_cper_state[i][j][k]);
+				if (v->byte_per_pixel_in_detc[k] == 0.0) {
+					v->urgent_latency_support_us_per_state[i][j][k] = v->effective_detlb_lines_luma * (v->htotal[k] / v->pixel_clock[k]) / v->v_ratio[k] - v->effective_detlb_lines_luma * v->swath_width_yper_state[i][j][k] *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / (v->return_bw_per_state[i] / v->no_of_dpp[i][j][k]);
+				}
+				else {
+					v->urgent_latency_support_us_per_state[i][j][k] =dcn_bw_min2(v->effective_detlb_lines_luma * (v->htotal[k] / v->pixel_clock[k]) / v->v_ratio[k] - v->effective_detlb_lines_luma * v->swath_width_yper_state[i][j][k] *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / (v->return_bw_per_state[i] / v->no_of_dpp[i][j][k]), v->effective_detlb_lines_chroma * (v->htotal[k] / v->pixel_clock[k]) / (v->v_ratio[k] / 2.0) - v->effective_detlb_lines_chroma * v->swath_width_yper_state[i][j][k] / 2.0 *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / (v->return_bw_per_state[i] / v->no_of_dpp[i][j][k]));
+				}
+			}
+		}
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		for (j = 0; j <= 1; j++) {
+			v->urgent_latency_support[i][j] = dcn_bw_yes;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->urgent_latency_support_us_per_state[i][j][k] < v->urgent_latency / 1.0) {
+					v->urgent_latency_support[i][j] = dcn_bw_no;
+				}
+			}
+		}
+	}
+	/*prefetch check*/
+
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		for (j = 0; j <= 1; j++) {
+			v->total_number_of_dcc_active_dpp[i][j] = 0.0;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->dcc_enable[k] == dcn_bw_yes) {
+					v->total_number_of_dcc_active_dpp[i][j] = v->total_number_of_dcc_active_dpp[i][j] + v->no_of_dpp[i][j][k];
+				}
+			}
+		}
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		for (j = 0; j <= 1; j++) {
+			v->projected_dcfclk_deep_sleep = 8.0;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, v->pixel_clock[k] / 16.0);
+				if (v->byte_per_pixel_in_detc[k] == 0.0) {
+					if (v->v_ratio[k] <= 1.0) {
+						v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, 1.1 *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 64.0 * v->h_ratio[k] * v->pixel_clock[k] / v->no_of_dpp[i][j][k]);
+					}
+					else {
+						v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, 1.1 *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 64.0 * v->pscl_factor[k] * v->required_dispclk[i][j] / (1 + j));
+					}
+				}
+				else {
+					if (v->v_ratio[k] <= 1.0) {
+						v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, 1.1 *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 32.0 * v->h_ratio[k] * v->pixel_clock[k] / v->no_of_dpp[i][j][k]);
+					}
+					else {
+						v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, 1.1 *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 32.0 * v->pscl_factor[k] * v->required_dispclk[i][j] / (1 + j));
+					}
+					if (v->v_ratio[k] / 2.0 <= 1.0) {
+						v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, 1.1 *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 32.0 * v->h_ratio[k] / 2.0 * v->pixel_clock[k] / v->no_of_dpp[i][j][k]);
+					}
+					else {
+						v->projected_dcfclk_deep_sleep =dcn_bw_max2(v->projected_dcfclk_deep_sleep, 1.1 *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 32.0 * v->pscl_factor_chroma[k] * v->required_dispclk[i][j] / (1 + j));
+					}
+				}
+			}
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->dcc_enable[k] == dcn_bw_yes) {
+					v->meta_req_height_y = 8.0 * v->read256_block_height_y[k];
+					v->meta_req_width_y = 64.0 * 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / v->meta_req_height_y;
+					v->meta_surface_width_y =dcn_bw_ceil2(v->viewport_width[k] / v->no_of_dpp[i][j][k] - 1.0, v->meta_req_width_y) + v->meta_req_width_y;
+					v->meta_surface_height_y =dcn_bw_ceil2(v->viewport_height[k] - 1.0, v->meta_req_height_y) + v->meta_req_height_y;
+					if (v->pte_enable == dcn_bw_yes) {
+						v->meta_pte_bytes_per_frame_y = (dcn_bw_ceil2((v->meta_surface_width_y * v->meta_surface_height_y *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 256.0 - 4096.0) / 8.0 / 4096.0, 1.0) + 1) * 64.0;
+					}
+					else {
+						v->meta_pte_bytes_per_frame_y = 0.0;
+					}
+					if (v->source_scan[k] == dcn_bw_hor) {
+						v->meta_row_bytes_y = v->meta_surface_width_y * v->meta_req_height_y *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 256.0;
+					}
+					else {
+						v->meta_row_bytes_y = v->meta_surface_height_y * v->meta_req_width_y *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / 256.0;
+					}
+				}
+				else {
+					v->meta_pte_bytes_per_frame_y = 0.0;
+					v->meta_row_bytes_y = 0.0;
+				}
+				if (v->pte_enable == dcn_bw_yes) {
+					if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+						v->macro_tile_block_size_bytes_y = 256.0;
+						v->macro_tile_block_height_y = 1.0;
+					}
+					else if (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d_x) {
+						v->macro_tile_block_size_bytes_y = 4096.0;
+						v->macro_tile_block_height_y = 4.0 * v->read256_block_height_y[k];
+					}
+					else if (v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_x) {
+						v->macro_tile_block_size_bytes_y = 64.0 * 1024;
+						v->macro_tile_block_height_y = 16.0 * v->read256_block_height_y[k];
+					}
+					else {
+						v->macro_tile_block_size_bytes_y = 256.0 * 1024;
+						v->macro_tile_block_height_y = 32.0 * v->read256_block_height_y[k];
+					}
+					if (v->macro_tile_block_size_bytes_y <= 65536.0) {
+						v->data_pte_req_height_y = v->macro_tile_block_height_y;
+					}
+					else {
+						v->data_pte_req_height_y = 16.0 * v->read256_block_height_y[k];
+					}
+					v->data_pte_req_width_y = 4096.0 /dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) / v->data_pte_req_height_y * 8;
+					if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+						v->dpte_bytes_per_row_y = 64.0 * (dcn_bw_ceil2((v->viewport_width[k] / v->no_of_dpp[i][j][k] *dcn_bw_min2(128.0, dcn_bw_pow(2.0,dcn_bw_floor2(dcn_bw_log(v->pte_buffer_size_in_requests * v->data_pte_req_width_y / (v->viewport_width[k] / v->no_of_dpp[i][j][k]), 2.0), 1.0))) - 1.0) / v->data_pte_req_width_y, 1.0) + 1);
+					}
+					else if (v->source_scan[k] == dcn_bw_hor) {
+						v->dpte_bytes_per_row_y = 64.0 * (dcn_bw_ceil2((v->viewport_width[k] / v->no_of_dpp[i][j][k] - 1.0) / v->data_pte_req_width_y, 1.0) + 1);
+					}
+					else {
+						v->dpte_bytes_per_row_y = 64.0 * (dcn_bw_ceil2((v->viewport_height[k] - 1.0) / v->data_pte_req_height_y, 1.0) + 1);
+					}
+				}
+				else {
+					v->dpte_bytes_per_row_y = 0.0;
+				}
+				if ((v->source_pixel_format[k] != dcn_bw_rgb_sub_64 && v->source_pixel_format[k] != dcn_bw_rgb_sub_32 && v->source_pixel_format[k] != dcn_bw_rgb_sub_16)) {
+					if (v->dcc_enable[k] == dcn_bw_yes) {
+						v->meta_req_height_c = 8.0 * v->read256_block_height_c[k];
+						v->meta_req_width_c = 64.0 * 256.0 /dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / v->meta_req_height_c;
+						v->meta_surface_width_c =dcn_bw_ceil2(v->viewport_width[k] / v->no_of_dpp[i][j][k] / 2.0 - 1.0, v->meta_req_width_c) + v->meta_req_width_c;
+						v->meta_surface_height_c =dcn_bw_ceil2(v->viewport_height[k] / 2.0 - 1.0, v->meta_req_height_c) + v->meta_req_height_c;
+						if (v->pte_enable == dcn_bw_yes) {
+							v->meta_pte_bytes_per_frame_c = (dcn_bw_ceil2((v->meta_surface_width_c * v->meta_surface_height_c *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 256.0 - 4096.0) / 8.0 / 4096.0, 1.0) + 1) * 64.0;
+						}
+						else {
+							v->meta_pte_bytes_per_frame_c = 0.0;
+						}
+						if (v->source_scan[k] == dcn_bw_hor) {
+							v->meta_row_bytes_c = v->meta_surface_width_c * v->meta_req_height_c *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 256.0;
+						}
+						else {
+							v->meta_row_bytes_c = v->meta_surface_height_c * v->meta_req_width_c *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 256.0;
+						}
+					}
+					else {
+						v->meta_pte_bytes_per_frame_c = 0.0;
+						v->meta_row_bytes_c = 0.0;
+					}
+					if (v->pte_enable == dcn_bw_yes) {
+						if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+							v->macro_tile_block_size_bytes_c = 256.0;
+							v->macro_tile_block_height_c = 1.0;
+						}
+						else if (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d_x) {
+							v->macro_tile_block_size_bytes_c = 4096.0;
+							v->macro_tile_block_height_c = 4.0 * v->read256_block_height_c[k];
+						}
+						else if (v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_x) {
+							v->macro_tile_block_size_bytes_c = 64.0 * 1024;
+							v->macro_tile_block_height_c = 16.0 * v->read256_block_height_c[k];
+						}
+						else {
+							v->macro_tile_block_size_bytes_c = 256.0 * 1024;
+							v->macro_tile_block_height_c = 32.0 * v->read256_block_height_c[k];
+						}
+						v->macro_tile_block_width_c = v->macro_tile_block_size_bytes_c /dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / v->macro_tile_block_height_c;
+						if (v->macro_tile_block_size_bytes_c <= 65536.0) {
+							v->data_pte_req_height_c = v->macro_tile_block_height_c;
+						}
+						else {
+							v->data_pte_req_height_c = 16.0 * v->read256_block_height_c[k];
+						}
+						v->data_pte_req_width_c = 4096.0 /dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / v->data_pte_req_height_c * 8;
+						if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+							v->dpte_bytes_per_row_c = 64.0 * (dcn_bw_ceil2((v->viewport_width[k] / v->no_of_dpp[i][j][k] / 2.0 * dcn_bw_min2(128.0, dcn_bw_pow(2.0,dcn_bw_floor2(dcn_bw_log(v->pte_buffer_size_in_requests * v->data_pte_req_width_c / (v->viewport_width[k] / v->no_of_dpp[i][j][k] / 2.0), 2.0), 1.0))) - 1.0) / v->data_pte_req_width_c, 1.0) + 1);
+						}
+						else if (v->source_scan[k] == dcn_bw_hor) {
+							v->dpte_bytes_per_row_c = 64.0 * (dcn_bw_ceil2((v->viewport_width[k] / v->no_of_dpp[i][j][k] / 2.0 - 1.0) / v->data_pte_req_width_c, 1.0) + 1);
+						}
+						else {
+							v->dpte_bytes_per_row_c = 64.0 * (dcn_bw_ceil2((v->viewport_height[k] / 2.0 - 1.0) / v->data_pte_req_height_c, 1.0) + 1);
+						}
+					}
+					else {
+						v->dpte_bytes_per_row_c = 0.0;
+					}
+				}
+				else {
+					v->dpte_bytes_per_row_c = 0.0;
+					v->meta_pte_bytes_per_frame_c = 0.0;
+					v->meta_row_bytes_c = 0.0;
+				}
+				v->dpte_bytes_per_row[k] = v->dpte_bytes_per_row_y + v->dpte_bytes_per_row_c;
+				v->meta_pte_bytes_per_frame[k] = v->meta_pte_bytes_per_frame_y + v->meta_pte_bytes_per_frame_c;
+				v->meta_row_bytes[k] = v->meta_row_bytes_y + v->meta_row_bytes_c;
+				v->v_init_y = (v->v_ratio[k] + v->vtaps[k] + 1.0 + v->interlace_output[k] * 0.5 * v->v_ratio[k]) / 2.0;
+				v->prefill_y[k] =dcn_bw_floor2(v->v_init_y, 1.0);
+				v->max_num_sw_y[k] =dcn_bw_ceil2((v->prefill_y[k] - 1.0) / v->swath_height_yper_state[i][j][k], 1.0) + 1;
+				if (v->prefill_y[k] > 1.0) {
+					v->max_partial_sw_y =dcn_bw_mod((v->prefill_y[k] - 2.0), v->swath_height_yper_state[i][j][k]);
+				}
+				else {
+					v->max_partial_sw_y =dcn_bw_mod((v->prefill_y[k] + v->swath_height_yper_state[i][j][k] - 2.0), v->swath_height_yper_state[i][j][k]);
+				}
+				v->max_partial_sw_y =dcn_bw_max2(1.0, v->max_partial_sw_y);
+				v->prefetch_lines_y[k] = v->max_num_sw_y[k] * v->swath_height_yper_state[i][j][k] + v->max_partial_sw_y;
+				if ((v->source_pixel_format[k] != dcn_bw_rgb_sub_64 && v->source_pixel_format[k] != dcn_bw_rgb_sub_32 && v->source_pixel_format[k] != dcn_bw_rgb_sub_16)) {
+					v->v_init_c = (v->v_ratio[k] / 2.0 + v->vtaps[k] + 1.0 + v->interlace_output[k] * 0.5 * v->v_ratio[k] / 2.0) / 2.0;
+					v->prefill_c[k] =dcn_bw_floor2(v->v_init_c, 1.0);
+					v->max_num_sw_c[k] =dcn_bw_ceil2((v->prefill_c[k] - 1.0) / v->swath_height_cper_state[i][j][k], 1.0) + 1;
+					if (v->prefill_c[k] > 1.0) {
+						v->max_partial_sw_c =dcn_bw_mod((v->prefill_c[k] - 2.0), v->swath_height_cper_state[i][j][k]);
+					}
+					else {
+						v->max_partial_sw_c =dcn_bw_mod((v->prefill_c[k] + v->swath_height_cper_state[i][j][k] - 2.0), v->swath_height_cper_state[i][j][k]);
+					}
+					v->max_partial_sw_c =dcn_bw_max2(1.0, v->max_partial_sw_c);
+					v->prefetch_lines_c[k] = v->max_num_sw_c[k] * v->swath_height_cper_state[i][j][k] + v->max_partial_sw_c;
+				}
+				else {
+					v->prefetch_lines_c[k] = 0.0;
+				}
+				v->dst_x_after_scaler = 90.0 * v->pixel_clock[k] / (v->required_dispclk[i][j] / (j + 1)) + 42.0 * v->pixel_clock[k] / v->required_dispclk[i][j];
+				if (v->no_of_dpp[i][j][k] > 1.0) {
+					v->dst_x_after_scaler = v->dst_x_after_scaler + v->scaler_rec_out_width[k] / 2.0;
+				}
+				if (v->output_format[k] == dcn_bw_420) {
+					v->dst_y_after_scaler = 1.0;
+				}
+				else {
+					v->dst_y_after_scaler = 0.0;
+				}
+				v->time_calc = 24.0 / v->projected_dcfclk_deep_sleep;
+				v->v_update_offset[k][j] = dcn_bw_ceil2(v->htotal[k] / 4.0, 1.0);
+				v->total_repeater_delay = v->max_inter_dcn_tile_repeaters * (2.0 / (v->required_dispclk[i][j] / (j + 1)) + 3.0 / v->required_dispclk[i][j]);
+				v->v_update_width[k][j] = (14.0 / v->projected_dcfclk_deep_sleep + 12.0 / (v->required_dispclk[i][j] / (j + 1)) + v->total_repeater_delay) * v->pixel_clock[k];
+				v->v_ready_offset[k][j] = dcn_bw_max2(150.0 / (v->required_dispclk[i][j] / (j + 1)), v->total_repeater_delay + 20.0 / v->projected_dcfclk_deep_sleep + 10.0 / (v->required_dispclk[i][j] / (j + 1))) * v->pixel_clock[k];
+				v->time_setup = (v->v_update_offset[k][j] + v->v_update_width[k][j] + v->v_ready_offset[k][j]) / v->pixel_clock[k];
+				v->extra_latency = v->urgent_round_trip_and_out_of_order_latency_per_state[i] + (v->total_number_of_active_dpp[i][j] * v->pixel_chunk_size_in_kbyte + v->total_number_of_dcc_active_dpp[i][j] * v->meta_chunk_size) * 1024.0 / v->return_bw_per_state[i];
+				if (v->pte_enable == dcn_bw_yes) {
+					v->extra_latency = v->extra_latency + v->total_number_of_active_dpp[i][j] * v->pte_chunk_size * 1024.0 / v->return_bw_per_state[i];
+				}
+				if (v->can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one == dcn_bw_yes) {
+					v->maximum_vstartup = v->vtotal[k] - v->vactive[k] - 1.0;
+				}
+				else {
+					v->maximum_vstartup = v->v_sync_plus_back_porch[k] - 1.0;
+				}
+
+				do {
+					v->line_times_for_prefetch[k] = v->maximum_vstartup - v->urgent_latency / (v->htotal[k] / v->pixel_clock[k]) - (v->time_calc + v->time_setup) / (v->htotal[k] / v->pixel_clock[k]) - (v->dst_y_after_scaler + v->dst_x_after_scaler / v->htotal[k]);
+					v->line_times_for_prefetch[k] =dcn_bw_floor2(4.0 * (v->line_times_for_prefetch[k] + 0.125), 1.0) / 4;
+					v->prefetch_bw[k] = (v->meta_pte_bytes_per_frame[k] + 2.0 * v->meta_row_bytes[k] + 2.0 * v->dpte_bytes_per_row[k] + v->prefetch_lines_y[k] * v->swath_width_yper_state[i][j][k] *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) + v->prefetch_lines_c[k] * v->swath_width_yper_state[i][j][k] / 2.0 *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0)) / (v->line_times_for_prefetch[k] * v->htotal[k] / v->pixel_clock[k]);
+
+					if (v->pte_enable == dcn_bw_yes && v->dcc_enable[k] == dcn_bw_yes) {
+						v->time_for_meta_pte_without_immediate_flip = dcn_bw_max3(
+								v->meta_pte_bytes_frame[k] / v->prefetch_bw[k],
+								v->extra_latency,
+								v->htotal[k] / v->pixel_clock[k] / 4.0);
+					} else {
+						v->time_for_meta_pte_without_immediate_flip = v->htotal[k] / v->pixel_clock[k] / 4.0;
+					}
+
+					if (v->pte_enable == dcn_bw_yes || v->dcc_enable[k] == dcn_bw_yes) {
+						v->time_for_meta_and_dpte_row_without_immediate_flip = dcn_bw_max3((
+								v->meta_row_bytes[k] + v->dpte_bytes_per_row[k]) / v->prefetch_bw[k],
+								v->htotal[k] / v->pixel_clock[k] - v->time_for_meta_pte_without_immediate_flip,
+								v->extra_latency);
+					} else {
+						v->time_for_meta_and_dpte_row_without_immediate_flip = dcn_bw_max2(
+								v->htotal[k] / v->pixel_clock[k] - v->time_for_meta_pte_without_immediate_flip,
+								v->extra_latency - v->time_for_meta_pte_with_immediate_flip);
+					}
+
+					v->lines_for_meta_pte_without_immediate_flip[k] =dcn_bw_floor2(4.0 * (v->time_for_meta_pte_without_immediate_flip / (v->htotal[k] / v->pixel_clock[k]) + 0.125), 1.0) / 4;
+					v->lines_for_meta_and_dpte_row_without_immediate_flip[k] =dcn_bw_floor2(4.0 * (v->time_for_meta_and_dpte_row_without_immediate_flip / (v->htotal[k] / v->pixel_clock[k]) + 0.125), 1.0) / 4;
+					v->maximum_vstartup = v->maximum_vstartup - 1;
+
+					if (v->lines_for_meta_pte_without_immediate_flip[k] < 32.0 && v->lines_for_meta_and_dpte_row_without_immediate_flip[k] < 16.0)
+						break;
+
+				} while(1);
+			}
+			v->bw_available_for_immediate_flip = v->return_bw_per_state[i];
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->bw_available_for_immediate_flip = v->bw_available_for_immediate_flip -dcn_bw_max2(v->read_bandwidth[k], v->prefetch_bw[k]);
+			}
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->total_immediate_flip_bytes[k] = 0.0;
+				if ((v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+					v->total_immediate_flip_bytes[k] = v->total_immediate_flip_bytes[k] + v->meta_pte_bytes_per_frame[k] + v->meta_row_bytes[k] + v->dpte_bytes_per_row[k];
+				}
+			}
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->pte_enable == dcn_bw_yes && v->dcc_enable[k] == dcn_bw_yes) {
+					v->time_for_meta_pte_with_immediate_flip =dcn_bw_max5(v->meta_pte_bytes_per_frame[k] / v->prefetch_bw[k], v->meta_pte_bytes_per_frame[k] * v->total_immediate_flip_bytes[k] / (v->bw_available_for_immediate_flip * (v->meta_pte_bytes_per_frame[k] + v->meta_row_bytes[k] + v->dpte_bytes_per_row[k])), v->extra_latency, v->urgent_latency, v->htotal[k] / v->pixel_clock[k] / 4.0);
+				}
+				else {
+					v->time_for_meta_pte_with_immediate_flip = v->htotal[k] / v->pixel_clock[k] / 4.0;
+				}
+				if (v->pte_enable == dcn_bw_yes || v->dcc_enable[k] == dcn_bw_yes) {
+					v->time_for_meta_and_dpte_row_with_immediate_flip =dcn_bw_max5((v->meta_row_bytes[k] + v->dpte_bytes_per_row[k]) / v->prefetch_bw[k], (v->meta_row_bytes[k] + v->dpte_bytes_per_row[k]) * v->total_immediate_flip_bytes[k] / (v->bw_available_for_immediate_flip * (v->meta_pte_bytes_per_frame[k] + v->meta_row_bytes[k] + v->dpte_bytes_per_row[k])), v->htotal[k] / v->pixel_clock[k] - v->time_for_meta_pte_with_immediate_flip, v->extra_latency, 2.0 * v->urgent_latency);
+				}
+				else {
+					v->time_for_meta_and_dpte_row_with_immediate_flip =dcn_bw_max2(v->htotal[k] / v->pixel_clock[k] - v->time_for_meta_pte_with_immediate_flip, v->extra_latency - v->time_for_meta_pte_with_immediate_flip);
+				}
+				v->lines_for_meta_pte_with_immediate_flip[k] =dcn_bw_floor2(4.0 * (v->time_for_meta_pte_with_immediate_flip / (v->htotal[k] / v->pixel_clock[k]) + 0.125), 1.0) / 4;
+				v->lines_for_meta_and_dpte_row_with_immediate_flip[k] =dcn_bw_floor2(4.0 * (v->time_for_meta_and_dpte_row_with_immediate_flip / (v->htotal[k] / v->pixel_clock[k]) + 0.125), 1.0) / 4;
+				v->line_times_to_request_prefetch_pixel_data_with_immediate_flip = v->line_times_for_prefetch[k] - v->lines_for_meta_pte_with_immediate_flip[k] - v->lines_for_meta_and_dpte_row_with_immediate_flip[k];
+				v->line_times_to_request_prefetch_pixel_data_without_immediate_flip = v->line_times_for_prefetch[k] - v->lines_for_meta_pte_without_immediate_flip[k] - v->lines_for_meta_and_dpte_row_without_immediate_flip[k];
+				if (v->line_times_to_request_prefetch_pixel_data_with_immediate_flip > 0.0) {
+					v->v_ratio_pre_ywith_immediate_flip[i][j][k] = v->prefetch_lines_y[k] / v->line_times_to_request_prefetch_pixel_data_with_immediate_flip;
+					if ((v->swath_height_yper_state[i][j][k] > 4.0)) {
+						if (v->line_times_to_request_prefetch_pixel_data_with_immediate_flip - (v->prefill_y[k] - 3.0) / 2.0 > 0.0) {
+							v->v_ratio_pre_ywith_immediate_flip[i][j][k] =dcn_bw_max2(v->v_ratio_pre_ywith_immediate_flip[i][j][k], (v->max_num_sw_y[k] * v->swath_height_yper_state[i][j][k]) / (v->line_times_to_request_prefetch_pixel_data_with_immediate_flip - (v->prefill_y[k] - 3.0) / 2.0));
+						}
+						else {
+							v->v_ratio_pre_ywith_immediate_flip[i][j][k] = 999999.0;
+						}
+					}
+					v->v_ratio_pre_cwith_immediate_flip[i][j][k] = v->prefetch_lines_c[k] / v->line_times_to_request_prefetch_pixel_data_with_immediate_flip;
+					if ((v->swath_height_cper_state[i][j][k] > 4.0)) {
+						if (v->line_times_to_request_prefetch_pixel_data_with_immediate_flip - (v->prefill_c[k] - 3.0) / 2.0 > 0.0) {
+							v->v_ratio_pre_cwith_immediate_flip[i][j][k] =dcn_bw_max2(v->v_ratio_pre_cwith_immediate_flip[i][j][k], (v->max_num_sw_c[k] * v->swath_height_cper_state[i][j][k]) / (v->line_times_to_request_prefetch_pixel_data_with_immediate_flip - (v->prefill_c[k] - 3.0) / 2.0));
+						}
+						else {
+							v->v_ratio_pre_cwith_immediate_flip[i][j][k] = 999999.0;
+						}
+					}
+					v->required_prefetch_pixel_data_bw_with_immediate_flip[i][j][k] = v->no_of_dpp[i][j][k] * (v->prefetch_lines_y[k] / v->line_times_to_request_prefetch_pixel_data_with_immediate_flip *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) + v->prefetch_lines_c[k] / v->line_times_to_request_prefetch_pixel_data_with_immediate_flip *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 2.0) * v->swath_width_yper_state[i][j][k] / (v->htotal[k] / v->pixel_clock[k]);
+				}
+				else {
+					v->v_ratio_pre_ywith_immediate_flip[i][j][k] = 999999.0;
+					v->v_ratio_pre_cwith_immediate_flip[i][j][k] = 999999.0;
+					v->required_prefetch_pixel_data_bw_with_immediate_flip[i][j][k] = 999999.0;
+				}
+				if (v->line_times_to_request_prefetch_pixel_data_without_immediate_flip > 0.0) {
+					v->v_ratio_pre_ywithout_immediate_flip[i][j][k] = v->prefetch_lines_y[k] / v->line_times_to_request_prefetch_pixel_data_without_immediate_flip;
+					if ((v->swath_height_yper_state[i][j][k] > 4.0)) {
+						if (v->line_times_to_request_prefetch_pixel_data_without_immediate_flip - (v->prefill_y[k] - 3.0) / 2.0 > 0.0) {
+							v->v_ratio_pre_ywithout_immediate_flip[i][j][k] =dcn_bw_max2(v->v_ratio_pre_ywithout_immediate_flip[i][j][k], (v->max_num_sw_y[k] * v->swath_height_yper_state[i][j][k]) / (v->line_times_to_request_prefetch_pixel_data_without_immediate_flip - (v->prefill_y[k] - 3.0) / 2.0));
+						}
+						else {
+							v->v_ratio_pre_ywithout_immediate_flip[i][j][k] = 999999.0;
+						}
+					}
+					v->v_ratio_pre_cwithout_immediate_flip[i][j][k] = v->prefetch_lines_c[k] / v->line_times_to_request_prefetch_pixel_data_without_immediate_flip;
+					if ((v->swath_height_cper_state[i][j][k] > 4.0)) {
+						if (v->line_times_to_request_prefetch_pixel_data_without_immediate_flip - (v->prefill_c[k] - 3.0) / 2.0 > 0.0) {
+							v->v_ratio_pre_cwithout_immediate_flip[i][j][k] =dcn_bw_max2(v->v_ratio_pre_cwithout_immediate_flip[i][j][k], (v->max_num_sw_c[k] * v->swath_height_cper_state[i][j][k]) / (v->line_times_to_request_prefetch_pixel_data_without_immediate_flip - (v->prefill_c[k] - 3.0) / 2.0));
+						}
+						else {
+							v->v_ratio_pre_cwithout_immediate_flip[i][j][k] = 999999.0;
+						}
+					}
+					v->required_prefetch_pixel_data_bw_without_immediate_flip[i][j][k] = v->no_of_dpp[i][j][k] * (v->prefetch_lines_y[k] / v->line_times_to_request_prefetch_pixel_data_without_immediate_flip *dcn_bw_ceil2(v->byte_per_pixel_in_dety[k], 1.0) + v->prefetch_lines_c[k] / v->line_times_to_request_prefetch_pixel_data_without_immediate_flip *dcn_bw_ceil2(v->byte_per_pixel_in_detc[k], 2.0) / 2.0) * v->swath_width_yper_state[i][j][k] / (v->htotal[k] / v->pixel_clock[k]);
+				}
+				else {
+					v->v_ratio_pre_ywithout_immediate_flip[i][j][k] = 999999.0;
+					v->v_ratio_pre_cwithout_immediate_flip[i][j][k] = 999999.0;
+					v->required_prefetch_pixel_data_bw_without_immediate_flip[i][j][k] = 999999.0;
+				}
+			}
+			v->maximum_read_bandwidth_with_prefetch_with_immediate_flip = 0.0;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if ((v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+					v->maximum_read_bandwidth_with_prefetch_with_immediate_flip = v->maximum_read_bandwidth_with_prefetch_with_immediate_flip +dcn_bw_max2(v->read_bandwidth[k], v->required_prefetch_pixel_data_bw_with_immediate_flip[i][j][k]) +dcn_bw_max2(v->meta_pte_bytes_per_frame[k] / (v->lines_for_meta_pte_with_immediate_flip[k] * v->htotal[k] / v->pixel_clock[k]), (v->meta_row_bytes[k] + v->dpte_bytes_per_row[k]) / (v->lines_for_meta_and_dpte_row_with_immediate_flip[k] * v->htotal[k] / v->pixel_clock[k]));
+				}
+				else {
+					v->maximum_read_bandwidth_with_prefetch_with_immediate_flip = v->maximum_read_bandwidth_with_prefetch_with_immediate_flip +dcn_bw_max2(v->read_bandwidth[k], v->required_prefetch_pixel_data_bw_without_immediate_flip[i][j][k]);
+				}
+			}
+			v->maximum_read_bandwidth_with_prefetch_without_immediate_flip = 0.0;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->maximum_read_bandwidth_with_prefetch_without_immediate_flip = v->maximum_read_bandwidth_with_prefetch_without_immediate_flip +dcn_bw_max2(v->read_bandwidth[k], v->required_prefetch_pixel_data_bw_without_immediate_flip[i][j][k]);
+			}
+			v->prefetch_supported_with_immediate_flip[i][j] = dcn_bw_yes;
+			if (v->maximum_read_bandwidth_with_prefetch_with_immediate_flip > v->return_bw_per_state[i]) {
+				v->prefetch_supported_with_immediate_flip[i][j] = dcn_bw_no;
+			}
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->line_times_for_prefetch[k] < 2.0 || v->lines_for_meta_pte_with_immediate_flip[k] >= 8.0 || v->lines_for_meta_and_dpte_row_with_immediate_flip[k] >= 16.0) {
+					v->prefetch_supported_with_immediate_flip[i][j] = dcn_bw_no;
+				}
+			}
+			v->prefetch_supported_without_immediate_flip[i][j] = dcn_bw_yes;
+			if (v->maximum_read_bandwidth_with_prefetch_without_immediate_flip > v->return_bw_per_state[i]) {
+				v->prefetch_supported_without_immediate_flip[i][j] = dcn_bw_no;
+			}
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->line_times_for_prefetch[k] < 2.0 || v->lines_for_meta_pte_without_immediate_flip[k] >= 8.0 || v->lines_for_meta_and_dpte_row_without_immediate_flip[k] >= 16.0) {
+					v->prefetch_supported_without_immediate_flip[i][j] = dcn_bw_no;
+				}
+			}
+		}
+	}
+	for (i = 0; i <= number_of_states_plus_one; i++) {
+		for (j = 0; j <= 1; j++) {
+			v->v_ratio_in_prefetch_supported_with_immediate_flip[i][j] = dcn_bw_yes;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if ((((v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10) && (v->v_ratio_pre_ywith_immediate_flip[i][j][k] > 4.0 || v->v_ratio_pre_cwith_immediate_flip[i][j][k] > 4.0)) || ((v->source_pixel_format[k] == dcn_bw_yuv420_sub_8 || v->source_pixel_format[k] == dcn_bw_yuv420_sub_10) && (v->v_ratio_pre_ywithout_immediate_flip[i][j][k] > 4.0 || v->v_ratio_pre_cwithout_immediate_flip[i][j][k] > 4.0)))) {
+					v->v_ratio_in_prefetch_supported_with_immediate_flip[i][j] = dcn_bw_no;
+				}
+			}
+			v->v_ratio_in_prefetch_supported_without_immediate_flip[i][j] = dcn_bw_yes;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if ((v->v_ratio_pre_ywithout_immediate_flip[i][j][k] > 4.0 || v->v_ratio_pre_cwithout_immediate_flip[i][j][k] > 4.0)) {
+					v->v_ratio_in_prefetch_supported_without_immediate_flip[i][j] = dcn_bw_no;
+				}
+			}
+		}
+	}
+	/*mode support, voltage state and soc configuration*/
+
+	for (i = number_of_states_plus_one; i >= 0; i--) {
+		for (j = 0; j <= 1; j++) {
+			if (v->scale_ratio_support == dcn_bw_yes && v->source_format_pixel_and_scan_support == dcn_bw_yes && v->viewport_size_support == dcn_bw_yes && v->bandwidth_support[i] == dcn_bw_yes && v->dio_support[i] == dcn_bw_yes && v->urgent_latency_support[i][j] == dcn_bw_yes && v->rob_support[i] == dcn_bw_yes && v->dispclk_dppclk_support[i][j] == dcn_bw_yes && v->total_available_pipes_support[i][j] == dcn_bw_yes && v->total_available_writeback_support == dcn_bw_yes && v->writeback_latency_support == dcn_bw_yes) {
+				if (v->prefetch_supported_with_immediate_flip[i][j] == dcn_bw_yes && v->v_ratio_in_prefetch_supported_with_immediate_flip[i][j] == dcn_bw_yes) {
+					v->mode_support_with_immediate_flip[i][j] = dcn_bw_yes;
+				}
+				else {
+					v->mode_support_with_immediate_flip[i][j] = dcn_bw_no;
+				}
+				if (v->prefetch_supported_without_immediate_flip[i][j] == dcn_bw_yes && v->v_ratio_in_prefetch_supported_without_immediate_flip[i][j] == dcn_bw_yes) {
+					v->mode_support_without_immediate_flip[i][j] = dcn_bw_yes;
+				}
+				else {
+					v->mode_support_without_immediate_flip[i][j] = dcn_bw_no;
+				}
+			}
+			else {
+				v->mode_support_with_immediate_flip[i][j] = dcn_bw_no;
+				v->mode_support_without_immediate_flip[i][j] = dcn_bw_no;
+			}
+		}
+	}
+	for (i = number_of_states_plus_one; i >= 0; i--) {
+		if ((i == number_of_states_plus_one || v->mode_support_with_immediate_flip[i][1] == dcn_bw_yes || v->mode_support_with_immediate_flip[i][0] == dcn_bw_yes) && i >= v->voltage_override_level) {
+			v->voltage_level_with_immediate_flip = i;
+		}
+	}
+	for (i = number_of_states_plus_one; i >= 0; i--) {
+		if ((i == number_of_states_plus_one || v->mode_support_without_immediate_flip[i][1] == dcn_bw_yes || v->mode_support_without_immediate_flip[i][0] == dcn_bw_yes) && i >= v->voltage_override_level) {
+			v->voltage_level_without_immediate_flip = i;
+		}
+	}
+	if (v->voltage_level_with_immediate_flip == number_of_states_plus_one) {
+		v->immediate_flip_supported = dcn_bw_no;
+		v->voltage_level = v->voltage_level_without_immediate_flip;
+	}
+	else {
+		v->immediate_flip_supported = dcn_bw_yes;
+		v->voltage_level = v->voltage_level_with_immediate_flip;
+	}
+	v->dcfclk = v->dcfclk_per_state[v->voltage_level];
+	v->fabric_and_dram_bandwidth = v->fabric_and_dram_bandwidth_per_state[v->voltage_level];
+	for (j = 0; j <= 1; j++) {
+		v->required_dispclk_per_ratio[j] = v->required_dispclk[v->voltage_level][j];
+		for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+			v->dpp_per_plane_per_ratio[j][k] = v->no_of_dpp[v->voltage_level][j][k];
+		}
+		v->dispclk_dppclk_support_per_ratio[j] = v->dispclk_dppclk_support[v->voltage_level][j];
+	}
+	v->max_phyclk = v->phyclk_per_state[v->voltage_level];
+}
+void display_pipe_configuration(struct dcn_bw_internal_vars *v)
+{
+	int j;
+	int k;
+	/*display pipe configuration*/
+
+	for (j = 0; j <= 1; j++) {
+		v->total_number_of_active_dpp_per_ratio[j] = 0.0;
+		for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+			v->total_number_of_active_dpp_per_ratio[j] = v->total_number_of_active_dpp_per_ratio[j] + v->dpp_per_plane_per_ratio[j][k];
+		}
+	}
+	if ((v->dispclk_dppclk_support_per_ratio[0] == dcn_bw_yes && v->dispclk_dppclk_support_per_ratio[1] == dcn_bw_no) || (v->dispclk_dppclk_support_per_ratio[0] == v->dispclk_dppclk_support_per_ratio[1] && (v->total_number_of_active_dpp_per_ratio[0] < v->total_number_of_active_dpp_per_ratio[1] || (((v->total_number_of_active_dpp_per_ratio[0] == v->total_number_of_active_dpp_per_ratio[1]) && v->required_dispclk_per_ratio[0] <= 0.5 * v->required_dispclk_per_ratio[1]))))) {
+		v->dispclk_dppclk_ratio = 1;
+		v->final_error_message = v->error_message[0];
+	}
+	else {
+		v->dispclk_dppclk_ratio = 2;
+		v->final_error_message = v->error_message[1];
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->dpp_per_plane[k] = v->dpp_per_plane_per_ratio[v->dispclk_dppclk_ratio - 1][k];
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+			v->byte_per_pix_dety = 8.0;
+			v->byte_per_pix_detc = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_32) {
+			v->byte_per_pix_dety = 4.0;
+			v->byte_per_pix_detc = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_16) {
+			v->byte_per_pix_dety = 2.0;
+			v->byte_per_pix_detc = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+			v->byte_per_pix_dety = 1.0;
+			v->byte_per_pix_detc = 2.0;
+		}
+		else {
+			v->byte_per_pix_dety = 4.0f / 3.0f;
+			v->byte_per_pix_detc = 8.0f / 3.0f;
+		}
+		if ((v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32 || v->source_pixel_format[k] == dcn_bw_rgb_sub_16)) {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->read256_bytes_block_height_y = 1.0;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+				v->read256_bytes_block_height_y = 4.0;
+			}
+			else {
+				v->read256_bytes_block_height_y = 8.0;
+			}
+			v->read256_bytes_block_width_y = 256.0 /dcn_bw_ceil2(v->byte_per_pix_dety, 1.0) / v->read256_bytes_block_height_y;
+			v->read256_bytes_block_height_c = 0.0;
+			v->read256_bytes_block_width_c = 0.0;
+		}
+		else {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->read256_bytes_block_height_y = 1.0;
+				v->read256_bytes_block_height_c = 1.0;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+				v->read256_bytes_block_height_y = 16.0;
+				v->read256_bytes_block_height_c = 8.0;
+			}
+			else {
+				v->read256_bytes_block_height_y = 8.0;
+				v->read256_bytes_block_height_c = 8.0;
+			}
+			v->read256_bytes_block_width_y = 256.0 /dcn_bw_ceil2(v->byte_per_pix_dety, 1.0) / v->read256_bytes_block_height_y;
+			v->read256_bytes_block_width_c = 256.0 /dcn_bw_ceil2(v->byte_per_pix_detc, 2.0) / v->read256_bytes_block_height_c;
+		}
+		if (v->source_scan[k] == dcn_bw_hor) {
+			v->maximum_swath_height_y = v->read256_bytes_block_height_y;
+			v->maximum_swath_height_c = v->read256_bytes_block_height_c;
+		}
+		else {
+			v->maximum_swath_height_y = v->read256_bytes_block_width_y;
+			v->maximum_swath_height_c = v->read256_bytes_block_width_c;
+		}
+		if ((v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32 || v->source_pixel_format[k] == dcn_bw_rgb_sub_16)) {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear || (v->source_pixel_format[k] == dcn_bw_rgb_sub_64 && (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_var_s || v->source_surface_mode[k] == dcn_bw_sw_var_s_x) && v->source_scan[k] == dcn_bw_hor)) {
+				v->minimum_swath_height_y = v->maximum_swath_height_y;
+			}
+			else {
+				v->minimum_swath_height_y = v->maximum_swath_height_y / 2.0;
+			}
+			v->minimum_swath_height_c = v->maximum_swath_height_c;
+		}
+		else {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->minimum_swath_height_y = v->maximum_swath_height_y;
+				v->minimum_swath_height_c = v->maximum_swath_height_c;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8 && v->source_scan[k] == dcn_bw_hor) {
+				v->minimum_swath_height_y = v->maximum_swath_height_y / 2.0;
+				if (v->bug_forcing_luma_and_chroma_request_to_same_size_fixed == dcn_bw_yes) {
+					v->minimum_swath_height_c = v->maximum_swath_height_c;
+				}
+				else {
+					v->minimum_swath_height_c = v->maximum_swath_height_c / 2.0;
+				}
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_10 && v->source_scan[k] == dcn_bw_hor) {
+				v->minimum_swath_height_c = v->maximum_swath_height_c / 2.0;
+				if (v->bug_forcing_luma_and_chroma_request_to_same_size_fixed == dcn_bw_yes) {
+					v->minimum_swath_height_y = v->maximum_swath_height_y;
+				}
+				else {
+					v->minimum_swath_height_y = v->maximum_swath_height_y / 2.0;
+				}
+			}
+			else {
+				v->minimum_swath_height_y = v->maximum_swath_height_y;
+				v->minimum_swath_height_c = v->maximum_swath_height_c;
+			}
+		}
+		if (v->source_scan[k] == dcn_bw_hor) {
+			v->swath_width = v->viewport_width[k] / v->dpp_per_plane[k];
+		}
+		else {
+			v->swath_width = v->viewport_height[k] / v->dpp_per_plane[k];
+		}
+		v->swath_width_granularity_y = 256.0 /dcn_bw_ceil2(v->byte_per_pix_dety, 1.0) / v->maximum_swath_height_y;
+		v->rounded_up_max_swath_size_bytes_y = (dcn_bw_ceil2(v->swath_width - 1.0, v->swath_width_granularity_y) + v->swath_width_granularity_y) * v->byte_per_pix_dety * v->maximum_swath_height_y;
+		if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_10) {
+			v->rounded_up_max_swath_size_bytes_y =dcn_bw_ceil2(v->rounded_up_max_swath_size_bytes_y, 256.0) + 256;
+		}
+		if (v->maximum_swath_height_c > 0.0) {
+			v->swath_width_granularity_c = 256.0 /dcn_bw_ceil2(v->byte_per_pix_detc, 2.0) / v->maximum_swath_height_c;
+		}
+		v->rounded_up_max_swath_size_bytes_c = (dcn_bw_ceil2(v->swath_width / 2.0 - 1.0, v->swath_width_granularity_c) + v->swath_width_granularity_c) * v->byte_per_pix_detc * v->maximum_swath_height_c;
+		if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_10) {
+			v->rounded_up_max_swath_size_bytes_c =dcn_bw_ceil2(v->rounded_up_max_swath_size_bytes_c, 256.0) + 256;
+		}
+		if (v->rounded_up_max_swath_size_bytes_y + v->rounded_up_max_swath_size_bytes_c <= v->det_buffer_size_in_kbyte * 1024.0 / 2.0) {
+			v->swath_height_y[k] = v->maximum_swath_height_y;
+			v->swath_height_c[k] = v->maximum_swath_height_c;
+		}
+		else {
+			v->swath_height_y[k] = v->minimum_swath_height_y;
+			v->swath_height_c[k] = v->minimum_swath_height_c;
+		}
+		if (v->swath_height_c[k] == 0.0) {
+			v->det_buffer_size_y[k] = v->det_buffer_size_in_kbyte * 1024.0;
+			v->det_buffer_size_c[k] = 0.0;
+		}
+		else if (v->swath_height_y[k] <= v->swath_height_c[k]) {
+			v->det_buffer_size_y[k] = v->det_buffer_size_in_kbyte * 1024.0 / 2.0;
+			v->det_buffer_size_c[k] = v->det_buffer_size_in_kbyte * 1024.0 / 2.0;
+		}
+		else {
+			v->det_buffer_size_y[k] = v->det_buffer_size_in_kbyte * 1024.0 * 2.0 / 3.0;
+			v->det_buffer_size_c[k] = v->det_buffer_size_in_kbyte * 1024.0 / 3.0;
+		}
+	}
+}
+void dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(struct dcn_bw_internal_vars *v)
+{
+	int k;
+	/*dispclk and dppclk calculation*/
+
+	v->dispclk_with_ramping = 0.0;
+	v->dispclk_without_ramping = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->h_ratio[k] > 1.0) {
+			v->pscl_throughput[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput * v->h_ratio[k] /dcn_bw_ceil2(v->htaps[k] / 6.0, 1.0));
+		}
+		else {
+			v->pscl_throughput[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput);
+		}
+		v->dppclk_using_single_dpp_luma = v->pixel_clock[k] *dcn_bw_max3(v->vtaps[k] / 6.0 *dcn_bw_min2(1.0, v->h_ratio[k]), v->h_ratio[k] * v->v_ratio[k] / v->pscl_throughput[k], 1.0);
+		if ((v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+			v->pscl_throughput_chroma[k] = 0.0;
+			v->dppclk_using_single_dpp = v->dppclk_using_single_dpp_luma;
+		}
+		else {
+			if (v->h_ratio[k] > 1.0) {
+				v->pscl_throughput_chroma[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput * v->h_ratio[k] / 2.0 /dcn_bw_ceil2(v->hta_pschroma[k] / 6.0, 1.0));
+			}
+			else {
+				v->pscl_throughput_chroma[k] =dcn_bw_min2(v->max_dchub_topscl_throughput, v->max_pscl_tolb_throughput);
+			}
+			v->dppclk_using_single_dpp_chroma = v->pixel_clock[k] *dcn_bw_max3(v->vta_pschroma[k] / 6.0 *dcn_bw_min2(1.0, v->h_ratio[k] / 2.0), v->h_ratio[k] * v->v_ratio[k] / 4.0 / v->pscl_throughput_chroma[k], 1.0);
+			v->dppclk_using_single_dpp =dcn_bw_max2(v->dppclk_using_single_dpp_luma, v->dppclk_using_single_dpp_chroma);
+		}
+		if (v->odm_capable == dcn_bw_yes) {
+			v->dispclk_with_ramping =dcn_bw_max2(v->dispclk_with_ramping,dcn_bw_max2(v->dppclk_using_single_dpp / v->dpp_per_plane[k] * v->dispclk_dppclk_ratio, v->pixel_clock[k] / v->dpp_per_plane[k]) * (1.0 + v->downspreading / 100.0) * (1.0 + v->dispclk_ramping_margin / 100.0));
+			v->dispclk_without_ramping =dcn_bw_max2(v->dispclk_without_ramping,dcn_bw_max2(v->dppclk_using_single_dpp / v->dpp_per_plane[k] * v->dispclk_dppclk_ratio, v->pixel_clock[k] / v->dpp_per_plane[k]) * (1.0 + v->downspreading / 100.0));
+		}
+		else {
+			v->dispclk_with_ramping =dcn_bw_max2(v->dispclk_with_ramping,dcn_bw_max2(v->dppclk_using_single_dpp / v->dpp_per_plane[k] * v->dispclk_dppclk_ratio, v->pixel_clock[k]) * (1.0 + v->downspreading / 100.0) * (1.0 + v->dispclk_ramping_margin / 100.0));
+			v->dispclk_without_ramping =dcn_bw_max2(v->dispclk_without_ramping,dcn_bw_max2(v->dppclk_using_single_dpp / v->dpp_per_plane[k] * v->dispclk_dppclk_ratio, v->pixel_clock[k]) * (1.0 + v->downspreading / 100.0));
+		}
+	}
+	if (v->dispclk_without_ramping > v->max_dispclk[number_of_states]) {
+		v->dispclk = v->dispclk_without_ramping;
+	}
+	else if (v->dispclk_with_ramping > v->max_dispclk[number_of_states]) {
+		v->dispclk = v->max_dispclk[number_of_states];
+	}
+	else {
+		v->dispclk = v->dispclk_with_ramping;
+	}
+	v->dppclk = v->dispclk / v->dispclk_dppclk_ratio;
+	/*urgent watermark*/
+
+	v->return_bandwidth_to_dcn =dcn_bw_min2(v->return_bus_width * v->dcfclk, v->fabric_and_dram_bandwidth * 1000.0 * v->percent_of_ideal_drambw_received_after_urg_latency / 100.0);
+	v->dcc_enabled_any_plane = dcn_bw_no;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->dcc_enabled_any_plane = dcn_bw_yes;
+		}
+	}
+	v->return_bw = v->return_bandwidth_to_dcn;
+	if (v->dcc_enabled_any_plane == dcn_bw_yes && v->return_bandwidth_to_dcn > v->dcfclk * v->return_bus_width / 4.0) {
+		v->return_bw =dcn_bw_min2(v->return_bw, v->return_bandwidth_to_dcn * 4.0 * (1.0 - v->urgent_latency / ((v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 / (v->return_bandwidth_to_dcn - v->dcfclk * v->return_bus_width / 4.0) + v->urgent_latency)));
+	}
+	v->critical_compression = 2.0 * v->return_bus_width * v->dcfclk * v->urgent_latency / (v->return_bandwidth_to_dcn * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0);
+	if (v->dcc_enabled_any_plane == dcn_bw_yes && v->critical_compression > 1.0 && v->critical_compression < 4.0) {
+		v->return_bw =dcn_bw_min2(v->return_bw, dcn_bw_pow(4.0 * v->return_bandwidth_to_dcn * (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 * v->return_bus_width * v->dcfclk * v->urgent_latency / (v->return_bandwidth_to_dcn * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0), 2));
+	}
+	v->return_bandwidth_to_dcn =dcn_bw_min2(v->return_bus_width * v->dcfclk, v->fabric_and_dram_bandwidth * 1000.0);
+	if (v->dcc_enabled_any_plane == dcn_bw_yes && v->return_bandwidth_to_dcn > v->dcfclk * v->return_bus_width / 4.0) {
+		v->return_bw =dcn_bw_min2(v->return_bw, v->return_bandwidth_to_dcn * 4.0 * (1.0 - v->urgent_latency / ((v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 / (v->return_bandwidth_to_dcn - v->dcfclk * v->return_bus_width / 4.0) + v->urgent_latency)));
+	}
+	v->critical_compression = 2.0 * v->return_bus_width * v->dcfclk * v->urgent_latency / (v->return_bandwidth_to_dcn * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0);
+	if (v->dcc_enabled_any_plane == dcn_bw_yes && v->critical_compression > 1.0 && v->critical_compression < 4.0) {
+		v->return_bw =dcn_bw_min2(v->return_bw, dcn_bw_pow(4.0 * v->return_bandwidth_to_dcn * (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0 * v->return_bus_width * v->dcfclk * v->urgent_latency / (v->return_bandwidth_to_dcn * v->urgent_latency + (v->rob_buffer_size_in_kbyte - v->pixel_chunk_size_in_kbyte) * 1024.0), 2));
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->source_scan[k] == dcn_bw_hor) {
+			v->swath_width_y[k] = v->viewport_width[k] / v->dpp_per_plane[k];
+		}
+		else {
+			v->swath_width_y[k] = v->viewport_height[k] / v->dpp_per_plane[k];
+		}
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+			v->byte_per_pixel_dety[k] = 8.0;
+			v->byte_per_pixel_detc[k] = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_32) {
+			v->byte_per_pixel_dety[k] = 4.0;
+			v->byte_per_pixel_detc[k] = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_16) {
+			v->byte_per_pixel_dety[k] = 2.0;
+			v->byte_per_pixel_detc[k] = 0.0;
+		}
+		else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+			v->byte_per_pixel_dety[k] = 1.0;
+			v->byte_per_pixel_detc[k] = 2.0;
+		}
+		else {
+			v->byte_per_pixel_dety[k] = 4.0f / 3.0f;
+			v->byte_per_pixel_detc[k] = 8.0f / 3.0f;
+		}
+	}
+	v->total_data_read_bandwidth = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->read_bandwidth_plane_luma[k] = v->swath_width_y[k] * v->dpp_per_plane[k] *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / (v->htotal[k] / v->pixel_clock[k]) * v->v_ratio[k];
+		v->read_bandwidth_plane_chroma[k] = v->swath_width_y[k] / 2.0 * v->dpp_per_plane[k] *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / (v->htotal[k] / v->pixel_clock[k]) * v->v_ratio[k] / 2.0;
+		v->total_data_read_bandwidth = v->total_data_read_bandwidth + v->read_bandwidth_plane_luma[k] + v->read_bandwidth_plane_chroma[k];
+	}
+	v->total_active_dpp = 0.0;
+	v->total_dcc_active_dpp = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->total_active_dpp = v->total_active_dpp + v->dpp_per_plane[k];
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->total_dcc_active_dpp = v->total_dcc_active_dpp + v->dpp_per_plane[k];
+		}
+	}
+	v->urgent_round_trip_and_out_of_order_latency = (v->round_trip_ping_latency_cycles + 32.0) / v->dcfclk + v->urgent_out_of_order_return_per_channel * v->number_of_channels / v->return_bw;
+	v->last_pixel_of_line_extra_watermark = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->v_ratio[k] <= 1.0) {
+			v->display_pipe_line_delivery_time_luma[k] = v->swath_width_y[k] * v->dpp_per_plane[k] / v->h_ratio[k] / v->pixel_clock[k];
+		}
+		else {
+			v->display_pipe_line_delivery_time_luma[k] = v->swath_width_y[k] / v->pscl_throughput[k] / v->dppclk;
+		}
+		v->data_fabric_line_delivery_time_luma = v->swath_width_y[k] * v->swath_height_y[k] *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / (v->return_bw * v->read_bandwidth_plane_luma[k] / v->dpp_per_plane[k] / v->total_data_read_bandwidth);
+		v->last_pixel_of_line_extra_watermark =dcn_bw_max2(v->last_pixel_of_line_extra_watermark, v->data_fabric_line_delivery_time_luma - v->display_pipe_line_delivery_time_luma[k]);
+		if (v->byte_per_pixel_detc[k] == 0.0) {
+			v->display_pipe_line_delivery_time_chroma[k] = 0.0;
+		}
+		else {
+			if (v->v_ratio[k] / 2.0 <= 1.0) {
+				v->display_pipe_line_delivery_time_chroma[k] = v->swath_width_y[k] / 2.0 * v->dpp_per_plane[k] / (v->h_ratio[k] / 2.0) / v->pixel_clock[k];
+			}
+			else {
+				v->display_pipe_line_delivery_time_chroma[k] = v->swath_width_y[k] / 2.0 / v->pscl_throughput_chroma[k] / v->dppclk;
+			}
+			v->data_fabric_line_delivery_time_chroma = v->swath_width_y[k] / 2.0 * v->swath_height_c[k] *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / (v->return_bw * v->read_bandwidth_plane_chroma[k] / v->dpp_per_plane[k] / v->total_data_read_bandwidth);
+			v->last_pixel_of_line_extra_watermark =dcn_bw_max2(v->last_pixel_of_line_extra_watermark, v->data_fabric_line_delivery_time_chroma - v->display_pipe_line_delivery_time_chroma[k]);
+		}
+	}
+	v->urgent_extra_latency = v->urgent_round_trip_and_out_of_order_latency + (v->total_active_dpp * v->pixel_chunk_size_in_kbyte + v->total_dcc_active_dpp * v->meta_chunk_size) * 1024.0 / v->return_bw;
+	if (v->pte_enable == dcn_bw_yes) {
+		v->urgent_extra_latency = v->urgent_extra_latency + v->total_active_dpp * v->pte_chunk_size * 1024.0 / v->return_bw;
+	}
+	v->urgent_watermark = v->urgent_latency + v->last_pixel_of_line_extra_watermark + v->urgent_extra_latency;
+	v->ptemeta_urgent_watermark = v->urgent_watermark + 2.0 * v->urgent_latency;
+	/*nb p-state/dram clock change watermark*/
+
+	v->dram_clock_change_watermark = v->dram_clock_change_latency + v->urgent_watermark;
+	v->total_active_writeback = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->output[k] == dcn_bw_writeback) {
+			v->total_active_writeback = v->total_active_writeback + 1.0;
+		}
+	}
+	if (v->total_active_writeback <= 1.0) {
+		v->writeback_dram_clock_change_watermark = v->dram_clock_change_latency + v->write_back_latency;
+	}
+	else {
+		v->writeback_dram_clock_change_watermark = v->dram_clock_change_latency + v->write_back_latency + v->writeback_chunk_size * 1024.0 / 32.0 / v->socclk;
+	}
+	/*stutter efficiency*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->lines_in_dety[k] = v->det_buffer_size_y[k] / v->byte_per_pixel_dety[k] / v->swath_width_y[k];
+		v->lines_in_dety_rounded_down_to_swath[k] =dcn_bw_floor2(v->lines_in_dety[k], v->swath_height_y[k]);
+		v->full_det_buffering_time_y[k] = v->lines_in_dety_rounded_down_to_swath[k] * (v->htotal[k] / v->pixel_clock[k]) / v->v_ratio[k];
+		if (v->byte_per_pixel_detc[k] > 0.0) {
+			v->lines_in_detc[k] = v->det_buffer_size_c[k] / v->byte_per_pixel_detc[k] / (v->swath_width_y[k] / 2.0);
+			v->lines_in_detc_rounded_down_to_swath[k] =dcn_bw_floor2(v->lines_in_detc[k], v->swath_height_c[k]);
+			v->full_det_buffering_time_c[k] = v->lines_in_detc_rounded_down_to_swath[k] * (v->htotal[k] / v->pixel_clock[k]) / (v->v_ratio[k] / 2.0);
+		}
+		else {
+			v->lines_in_detc[k] = 0.0;
+			v->lines_in_detc_rounded_down_to_swath[k] = 0.0;
+			v->full_det_buffering_time_c[k] = 999999.0;
+		}
+	}
+	v->min_full_det_buffering_time = 999999.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->full_det_buffering_time_y[k] < v->min_full_det_buffering_time) {
+			v->min_full_det_buffering_time = v->full_det_buffering_time_y[k];
+			v->frame_time_for_min_full_det_buffering_time = v->vtotal[k] * v->htotal[k] / v->pixel_clock[k];
+		}
+		if (v->full_det_buffering_time_c[k] < v->min_full_det_buffering_time) {
+			v->min_full_det_buffering_time = v->full_det_buffering_time_c[k];
+			v->frame_time_for_min_full_det_buffering_time = v->vtotal[k] * v->htotal[k] / v->pixel_clock[k];
+		}
+	}
+	v->average_read_bandwidth_gbyte_per_second = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->average_read_bandwidth_gbyte_per_second = v->average_read_bandwidth_gbyte_per_second + v->read_bandwidth_plane_luma[k] / v->dcc_rate[k] / 1000.0 + v->read_bandwidth_plane_chroma[k] / v->dcc_rate[k] / 1000.0;
+		}
+		else {
+			v->average_read_bandwidth_gbyte_per_second = v->average_read_bandwidth_gbyte_per_second + v->read_bandwidth_plane_luma[k] / 1000.0 + v->read_bandwidth_plane_chroma[k] / 1000.0;
+		}
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->average_read_bandwidth_gbyte_per_second = v->average_read_bandwidth_gbyte_per_second + v->read_bandwidth_plane_luma[k] / 1000.0 / 256.0 + v->read_bandwidth_plane_chroma[k] / 1000.0 / 256.0;
+		}
+		if (v->pte_enable == dcn_bw_yes) {
+			v->average_read_bandwidth_gbyte_per_second = v->average_read_bandwidth_gbyte_per_second + v->read_bandwidth_plane_luma[k] / 1000.0 / 512.0 + v->read_bandwidth_plane_chroma[k] / 1000.0 / 512.0;
+		}
+	}
+	v->part_of_burst_that_fits_in_rob =dcn_bw_min2(v->min_full_det_buffering_time * v->total_data_read_bandwidth, v->rob_buffer_size_in_kbyte * 1024.0 * v->total_data_read_bandwidth / (v->average_read_bandwidth_gbyte_per_second * 1000.0));
+	v->stutter_burst_time = v->part_of_burst_that_fits_in_rob * (v->average_read_bandwidth_gbyte_per_second * 1000.0) / v->total_data_read_bandwidth / v->return_bw + (v->min_full_det_buffering_time * v->total_data_read_bandwidth - v->part_of_burst_that_fits_in_rob) / (v->dcfclk * 64.0);
+	if (v->total_active_writeback == 0.0) {
+		v->stutter_efficiency_not_including_vblank = (1.0 - (v->sr_exit_time + v->stutter_burst_time) / v->min_full_det_buffering_time) * 100.0;
+	}
+	else {
+		v->stutter_efficiency_not_including_vblank = 0.0;
+	}
+	v->smallest_vblank = 999999.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->synchronized_vblank == dcn_bw_yes || v->number_of_active_planes == 1) {
+			v->v_blank_time = (v->vtotal[k] - v->vactive[k]) * v->htotal[k] / v->pixel_clock[k];
+		}
+		else {
+			v->v_blank_time = 0.0;
+		}
+		v->smallest_vblank =dcn_bw_min2(v->smallest_vblank, v->v_blank_time);
+	}
+	v->stutter_efficiency = (v->stutter_efficiency_not_including_vblank / 100.0 * (v->frame_time_for_min_full_det_buffering_time - v->smallest_vblank) + v->smallest_vblank) / v->frame_time_for_min_full_det_buffering_time * 100.0;
+	/*dcfclk deep sleep*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->byte_per_pixel_detc[k] > 0.0) {
+			v->dcfclk_deep_sleep_per_plane[k] =dcn_bw_max2(1.1 * v->swath_width_y[k] *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / 32.0 / v->display_pipe_line_delivery_time_luma[k], 1.1 * v->swath_width_y[k] / 2.0 *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / 32.0 / v->display_pipe_line_delivery_time_chroma[k]);
+		}
+		else {
+			v->dcfclk_deep_sleep_per_plane[k] = 1.1 * v->swath_width_y[k] *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / 64.0 / v->display_pipe_line_delivery_time_luma[k];
+		}
+		v->dcfclk_deep_sleep_per_plane[k] =dcn_bw_max2(v->dcfclk_deep_sleep_per_plane[k], v->pixel_clock[k] / 16.0);
+	}
+	v->dcf_clk_deep_sleep = 8.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->dcf_clk_deep_sleep =dcn_bw_max2(v->dcf_clk_deep_sleep, v->dcfclk_deep_sleep_per_plane[k]);
+	}
+	/*stutter watermark*/
+
+	v->stutter_exit_watermark = v->sr_exit_time + v->last_pixel_of_line_extra_watermark + v->urgent_extra_latency + 10.0 / v->dcf_clk_deep_sleep;
+	v->stutter_enter_plus_exit_watermark = v->sr_enter_plus_exit_time + v->last_pixel_of_line_extra_watermark + v->urgent_extra_latency;
+	/*urgent latency supported*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->effective_det_plus_lb_lines_luma =dcn_bw_floor2(v->lines_in_dety[k] +dcn_bw_min2(v->lines_in_dety[k] * v->dppclk * v->byte_per_pixel_dety[k] * v->pscl_throughput[k] / (v->return_bw / v->dpp_per_plane[k]), v->effective_lb_latency_hiding_source_lines_luma), v->swath_height_y[k]);
+		v->urgent_latency_support_us_luma = v->effective_det_plus_lb_lines_luma * (v->htotal[k] / v->pixel_clock[k]) / v->v_ratio[k] - v->effective_det_plus_lb_lines_luma * v->swath_width_y[k] * v->byte_per_pixel_dety[k] / (v->return_bw / v->dpp_per_plane[k]);
+		if (v->byte_per_pixel_detc[k] > 0.0) {
+			v->effective_det_plus_lb_lines_chroma =dcn_bw_floor2(v->lines_in_detc[k] +dcn_bw_min2(v->lines_in_detc[k] * v->dppclk * v->byte_per_pixel_detc[k] * v->pscl_throughput_chroma[k] / (v->return_bw / v->dpp_per_plane[k]), v->effective_lb_latency_hiding_source_lines_chroma), v->swath_height_c[k]);
+			v->urgent_latency_support_us_chroma = v->effective_det_plus_lb_lines_chroma * (v->htotal[k] / v->pixel_clock[k]) / (v->v_ratio[k] / 2.0) - v->effective_det_plus_lb_lines_chroma * (v->swath_width_y[k] / 2.0) * v->byte_per_pixel_detc[k] / (v->return_bw / v->dpp_per_plane[k]);
+			v->urgent_latency_support_us[k] =dcn_bw_min2(v->urgent_latency_support_us_luma, v->urgent_latency_support_us_chroma);
+		}
+		else {
+			v->urgent_latency_support_us[k] = v->urgent_latency_support_us_luma;
+		}
+	}
+	v->min_urgent_latency_support_us = 999999.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->min_urgent_latency_support_us =dcn_bw_min2(v->min_urgent_latency_support_us, v->urgent_latency_support_us[k]);
+	}
+	/*non-urgent latency tolerance*/
+
+	v->non_urgent_latency_tolerance = v->min_urgent_latency_support_us - v->urgent_watermark;
+	/*prefetch*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if ((v->source_pixel_format[k] == dcn_bw_rgb_sub_64 || v->source_pixel_format[k] == dcn_bw_rgb_sub_32 || v->source_pixel_format[k] == dcn_bw_rgb_sub_16)) {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->block_height256_bytes_y = 1.0;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+				v->block_height256_bytes_y = 4.0;
+			}
+			else {
+				v->block_height256_bytes_y = 8.0;
+			}
+			v->block_height256_bytes_c = 0.0;
+		}
+		else {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->block_height256_bytes_y = 1.0;
+				v->block_height256_bytes_c = 1.0;
+			}
+			else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+				v->block_height256_bytes_y = 16.0;
+				v->block_height256_bytes_c = 8.0;
+			}
+			else {
+				v->block_height256_bytes_y = 8.0;
+				v->block_height256_bytes_c = 8.0;
+			}
+		}
+		if (v->dcc_enable[k] == dcn_bw_yes) {
+			v->meta_request_width_y = 64.0 * 256.0 /dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / (8.0 * v->block_height256_bytes_y);
+			v->meta_surf_width_y =dcn_bw_ceil2(v->swath_width_y[k] - 1.0, v->meta_request_width_y) + v->meta_request_width_y;
+			v->meta_surf_height_y =dcn_bw_ceil2(v->viewport_height[k] - 1.0, 8.0 * v->block_height256_bytes_y) + 8.0 * v->block_height256_bytes_y;
+			if (v->pte_enable == dcn_bw_yes) {
+				v->meta_pte_bytes_frame_y = (dcn_bw_ceil2((v->meta_surf_width_y * v->meta_surf_height_y *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / 256.0 - 4096.0) / 8.0 / 4096.0, 1.0) + 1) * 64.0;
+			}
+			else {
+				v->meta_pte_bytes_frame_y = 0.0;
+			}
+			if (v->source_scan[k] == dcn_bw_hor) {
+				v->meta_row_byte_y = v->meta_surf_width_y * 8.0 * v->block_height256_bytes_y *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / 256.0;
+			}
+			else {
+				v->meta_row_byte_y = v->meta_surf_height_y * v->meta_request_width_y *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / 256.0;
+			}
+		}
+		else {
+			v->meta_pte_bytes_frame_y = 0.0;
+			v->meta_row_byte_y = 0.0;
+		}
+		if (v->pte_enable == dcn_bw_yes) {
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->macro_tile_size_byte_y = 256.0;
+				v->macro_tile_height_y = 1.0;
+			}
+			else if (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d_x) {
+				v->macro_tile_size_byte_y = 4096.0;
+				v->macro_tile_height_y = 4.0 * v->block_height256_bytes_y;
+			}
+			else if (v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_x) {
+				v->macro_tile_size_byte_y = 64.0 * 1024;
+				v->macro_tile_height_y = 16.0 * v->block_height256_bytes_y;
+			}
+			else {
+				v->macro_tile_size_byte_y = 256.0 * 1024;
+				v->macro_tile_height_y = 32.0 * v->block_height256_bytes_y;
+			}
+			if (v->macro_tile_size_byte_y <= 65536.0) {
+				v->pixel_pte_req_height_y = v->macro_tile_height_y;
+			}
+			else {
+				v->pixel_pte_req_height_y = 16.0 * v->block_height256_bytes_y;
+			}
+			v->pixel_pte_req_width_y = 4096.0 /dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / v->pixel_pte_req_height_y * 8;
+			if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+				v->pixel_pte_bytes_per_row_y = 64.0 * (dcn_bw_ceil2((v->swath_width_y[k] *dcn_bw_min2(128.0, dcn_bw_pow(2.0,dcn_bw_floor2(dcn_bw_log(v->pte_buffer_size_in_requests * v->pixel_pte_req_width_y / v->swath_width_y[k], 2.0), 1.0))) - 1.0) / v->pixel_pte_req_width_y, 1.0) + 1);
+			}
+			else if (v->source_scan[k] == dcn_bw_hor) {
+				v->pixel_pte_bytes_per_row_y = 64.0 * (dcn_bw_ceil2((v->swath_width_y[k] - 1.0) / v->pixel_pte_req_width_y, 1.0) + 1);
+			}
+			else {
+				v->pixel_pte_bytes_per_row_y = 64.0 * (dcn_bw_ceil2((v->viewport_height[k] - 1.0) / v->pixel_pte_req_height_y, 1.0) + 1);
+			}
+		}
+		else {
+			v->pixel_pte_bytes_per_row_y = 0.0;
+		}
+		if ((v->source_pixel_format[k] != dcn_bw_rgb_sub_64 && v->source_pixel_format[k] != dcn_bw_rgb_sub_32 && v->source_pixel_format[k] != dcn_bw_rgb_sub_16)) {
+			if (v->dcc_enable[k] == dcn_bw_yes) {
+				v->meta_request_width_c = 64.0 * 256.0 /dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / (8.0 * v->block_height256_bytes_c);
+				v->meta_surf_width_c =dcn_bw_ceil2(v->swath_width_y[k] / 2.0 - 1.0, v->meta_request_width_c) + v->meta_request_width_c;
+				v->meta_surf_height_c =dcn_bw_ceil2(v->viewport_height[k] / 2.0 - 1.0, 8.0 * v->block_height256_bytes_c) + 8.0 * v->block_height256_bytes_c;
+				if (v->pte_enable == dcn_bw_yes) {
+					v->meta_pte_bytes_frame_c = (dcn_bw_ceil2((v->meta_surf_width_c * v->meta_surf_height_c *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / 256.0 - 4096.0) / 8.0 / 4096.0, 1.0) + 1) * 64.0;
+				}
+				else {
+					v->meta_pte_bytes_frame_c = 0.0;
+				}
+				if (v->source_scan[k] == dcn_bw_hor) {
+					v->meta_row_byte_c = v->meta_surf_width_c * 8.0 * v->block_height256_bytes_c *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / 256.0;
+				}
+				else {
+					v->meta_row_byte_c = v->meta_surf_height_c * v->meta_request_width_c *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / 256.0;
+				}
+			}
+			else {
+				v->meta_pte_bytes_frame_c = 0.0;
+				v->meta_row_byte_c = 0.0;
+			}
+			if (v->pte_enable == dcn_bw_yes) {
+				if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+					v->macro_tile_size_bytes_c = 256.0;
+					v->macro_tile_height_c = 1.0;
+				}
+				else if (v->source_surface_mode[k] == dcn_bw_sw_4_kb_s || v->source_surface_mode[k] == dcn_bw_sw_4_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d || v->source_surface_mode[k] == dcn_bw_sw_4_kb_d_x) {
+					v->macro_tile_size_bytes_c = 4096.0;
+					v->macro_tile_height_c = 4.0 * v->block_height256_bytes_c;
+				}
+				else if (v->source_surface_mode[k] == dcn_bw_sw_64_kb_s || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_s_x || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_t || v->source_surface_mode[k] == dcn_bw_sw_64_kb_d_x) {
+					v->macro_tile_size_bytes_c = 64.0 * 1024;
+					v->macro_tile_height_c = 16.0 * v->block_height256_bytes_c;
+				}
+				else {
+					v->macro_tile_size_bytes_c = 256.0 * 1024;
+					v->macro_tile_height_c = 32.0 * v->block_height256_bytes_c;
+				}
+				if (v->macro_tile_size_bytes_c <= 65536.0) {
+					v->pixel_pte_req_height_c = v->macro_tile_height_c;
+				}
+				else {
+					v->pixel_pte_req_height_c = 16.0 * v->block_height256_bytes_c;
+				}
+				v->pixel_pte_req_width_c = 4096.0 /dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / v->pixel_pte_req_height_c * 8;
+				if (v->source_surface_mode[k] == dcn_bw_sw_linear) {
+					v->pixel_pte_bytes_per_row_c = 64.0 * (dcn_bw_ceil2((v->swath_width_y[k] / 2.0 * dcn_bw_min2(128.0, dcn_bw_pow(2.0,dcn_bw_floor2(dcn_bw_log(v->pte_buffer_size_in_requests * v->pixel_pte_req_width_c / (v->swath_width_y[k] / 2.0), 2.0), 1.0))) - 1.0) / v->pixel_pte_req_width_c, 1.0) + 1);
+				}
+				else if (v->source_scan[k] == dcn_bw_hor) {
+					v->pixel_pte_bytes_per_row_c = 64.0 * (dcn_bw_ceil2((v->swath_width_y[k] / 2.0 - 1.0) / v->pixel_pte_req_width_c, 1.0) + 1);
+				}
+				else {
+					v->pixel_pte_bytes_per_row_c = 64.0 * (dcn_bw_ceil2((v->viewport_height[k] / 2.0 - 1.0) / v->pixel_pte_req_height_c, 1.0) + 1);
+				}
+			}
+			else {
+				v->pixel_pte_bytes_per_row_c = 0.0;
+			}
+		}
+		else {
+			v->pixel_pte_bytes_per_row_c = 0.0;
+			v->meta_pte_bytes_frame_c = 0.0;
+			v->meta_row_byte_c = 0.0;
+		}
+		v->pixel_pte_bytes_per_row[k] = v->pixel_pte_bytes_per_row_y + v->pixel_pte_bytes_per_row_c;
+		v->meta_pte_bytes_frame[k] = v->meta_pte_bytes_frame_y + v->meta_pte_bytes_frame_c;
+		v->meta_row_byte[k] = v->meta_row_byte_y + v->meta_row_byte_c;
+		v->v_init_pre_fill_y[k] =dcn_bw_floor2((v->v_ratio[k] + v->vtaps[k] + 1.0 + v->interlace_output[k] * 0.5 * v->v_ratio[k]) / 2.0, 1.0);
+		v->max_num_swath_y[k] =dcn_bw_ceil2((v->v_init_pre_fill_y[k] - 1.0) / v->swath_height_y[k], 1.0) + 1;
+		if (v->v_init_pre_fill_y[k] > 1.0) {
+			v->max_partial_swath_y =dcn_bw_mod((v->v_init_pre_fill_y[k] - 2.0), v->swath_height_y[k]);
+		}
+		else {
+			v->max_partial_swath_y =dcn_bw_mod((v->v_init_pre_fill_y[k] + v->swath_height_y[k] - 2.0), v->swath_height_y[k]);
+		}
+		v->max_partial_swath_y =dcn_bw_max2(1.0, v->max_partial_swath_y);
+		v->prefetch_source_lines_y[k] = v->max_num_swath_y[k] * v->swath_height_y[k] + v->max_partial_swath_y;
+		if ((v->source_pixel_format[k] != dcn_bw_rgb_sub_64 && v->source_pixel_format[k] != dcn_bw_rgb_sub_32 && v->source_pixel_format[k] != dcn_bw_rgb_sub_16)) {
+			v->v_init_pre_fill_c[k] =dcn_bw_floor2((v->v_ratio[k] / 2.0 + v->vtaps[k] + 1.0 + v->interlace_output[k] * 0.5 * v->v_ratio[k] / 2.0) / 2.0, 1.0);
+			v->max_num_swath_c[k] =dcn_bw_ceil2((v->v_init_pre_fill_c[k] - 1.0) / v->swath_height_c[k], 1.0) + 1;
+			if (v->v_init_pre_fill_c[k] > 1.0) {
+				v->max_partial_swath_c =dcn_bw_mod((v->v_init_pre_fill_c[k] - 2.0), v->swath_height_c[k]);
+			}
+			else {
+				v->max_partial_swath_c =dcn_bw_mod((v->v_init_pre_fill_c[k] + v->swath_height_c[k] - 2.0), v->swath_height_c[k]);
+			}
+			v->max_partial_swath_c =dcn_bw_max2(1.0, v->max_partial_swath_c);
+		}
+		else {
+			v->max_num_swath_c[k] = 0.0;
+			v->max_partial_swath_c = 0.0;
+		}
+		v->prefetch_source_lines_c[k] = v->max_num_swath_c[k] * v->swath_height_c[k] + v->max_partial_swath_c;
+	}
+	v->t_calc = 24.0 / v->dcf_clk_deep_sleep;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one == dcn_bw_yes) {
+			v->max_vstartup_lines[k] = v->vtotal[k] - v->vactive[k] - 1.0;
+		}
+		else {
+			v->max_vstartup_lines[k] = v->v_sync_plus_back_porch[k] - 1.0;
+		}
+	}
+	v->next_prefetch_mode = 0.0;
+	do {
+		v->v_startup_lines = 13.0;
+		do {
+			v->planes_with_room_to_increase_vstartup_prefetch_bw_less_than_active_bw = dcn_bw_yes;
+			v->planes_with_room_to_increase_vstartup_vratio_prefetch_more_than4 = dcn_bw_no;
+			v->planes_with_room_to_increase_vstartup_destination_line_times_for_prefetch_less_than2 = dcn_bw_no;
+			v->v_ratio_prefetch_more_than4 = dcn_bw_no;
+			v->destination_line_times_for_prefetch_less_than2 = dcn_bw_no;
+			v->prefetch_mode = v->next_prefetch_mode;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->dstx_after_scaler = 90.0 * v->pixel_clock[k] / v->dppclk + 42.0 * v->pixel_clock[k] / v->dispclk;
+				if (v->dpp_per_plane[k] > 1.0) {
+					v->dstx_after_scaler = v->dstx_after_scaler + v->scaler_rec_out_width[k] / 2.0;
+				}
+				if (v->output_format[k] == dcn_bw_420) {
+					v->dsty_after_scaler = 1.0;
+				}
+				else {
+					v->dsty_after_scaler = 0.0;
+				}
+				v->v_update_offset_pix[k] = dcn_bw_ceil2(v->htotal[k] / 4.0, 1.0);
+				v->total_repeater_delay_time = v->max_inter_dcn_tile_repeaters * (2.0 / v->dppclk + 3.0 / v->dispclk);
+				v->v_update_width_pix[k] = (14.0 / v->dcf_clk_deep_sleep + 12.0 / v->dppclk + v->total_repeater_delay_time) * v->pixel_clock[k];
+				v->v_ready_offset_pix[k] = dcn_bw_max2(150.0 / v->dppclk, v->total_repeater_delay_time + 20.0 / v->dcf_clk_deep_sleep + 10.0 / v->dppclk) * v->pixel_clock[k];
+				v->t_setup = (v->v_update_offset_pix[k] + v->v_update_width_pix[k] + v->v_ready_offset_pix[k]) / v->pixel_clock[k];
+				v->v_startup[k] =dcn_bw_min2(v->v_startup_lines, v->max_vstartup_lines[k]);
+				if (v->prefetch_mode == 0.0) {
+					v->t_wait =dcn_bw_max3(v->dram_clock_change_latency + v->urgent_latency, v->sr_enter_plus_exit_time, v->urgent_latency);
+				}
+				else if (v->prefetch_mode == 1.0) {
+					v->t_wait =dcn_bw_max2(v->sr_enter_plus_exit_time, v->urgent_latency);
+				}
+				else {
+					v->t_wait = v->urgent_latency;
+				}
+				v->destination_lines_for_prefetch[k] =dcn_bw_floor2(4.0 * (v->v_startup[k] - v->t_wait / (v->htotal[k] / v->pixel_clock[k]) - (v->t_calc + v->t_setup) / (v->htotal[k] / v->pixel_clock[k]) - (v->dsty_after_scaler + v->dstx_after_scaler / v->htotal[k]) + 0.125), 1.0) / 4;
+				if (v->destination_lines_for_prefetch[k] > 0.0) {
+					v->prefetch_bandwidth[k] = (v->meta_pte_bytes_frame[k] + 2.0 * v->meta_row_byte[k] + 2.0 * v->pixel_pte_bytes_per_row[k] + v->prefetch_source_lines_y[k] * v->swath_width_y[k] *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) + v->prefetch_source_lines_c[k] * v->swath_width_y[k] / 2.0 *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0)) / (v->destination_lines_for_prefetch[k] * v->htotal[k] / v->pixel_clock[k]);
+				}
+				else {
+					v->prefetch_bandwidth[k] = 999999.0;
+				}
+			}
+			v->bandwidth_available_for_immediate_flip = v->return_bw;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				v->bandwidth_available_for_immediate_flip = v->bandwidth_available_for_immediate_flip -dcn_bw_max2(v->read_bandwidth_plane_luma[k] + v->read_bandwidth_plane_chroma[k], v->prefetch_bandwidth[k]);
+			}
+			v->tot_immediate_flip_bytes = 0.0;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->immediate_flip_supported == dcn_bw_yes && (v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+					v->tot_immediate_flip_bytes = v->tot_immediate_flip_bytes + v->meta_pte_bytes_frame[k] + v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k];
+				}
+			}
+			v->max_rd_bandwidth = 0.0;
+			for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+				if (v->pte_enable == dcn_bw_yes && v->dcc_enable[k] == dcn_bw_yes) {
+					if (v->immediate_flip_supported == dcn_bw_yes && (v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+						v->time_for_fetching_meta_pte =dcn_bw_max5(v->meta_pte_bytes_frame[k] / v->prefetch_bandwidth[k], v->meta_pte_bytes_frame[k] * v->tot_immediate_flip_bytes / (v->bandwidth_available_for_immediate_flip * (v->meta_pte_bytes_frame[k] + v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k])), v->urgent_extra_latency, v->urgent_latency, v->htotal[k] / v->pixel_clock[k] / 4.0);
+					}
+					else {
+						v->time_for_fetching_meta_pte =dcn_bw_max3(v->meta_pte_bytes_frame[k] / v->prefetch_bandwidth[k], v->urgent_extra_latency, v->htotal[k] / v->pixel_clock[k] / 4.0);
+					}
+				}
+				else {
+					v->time_for_fetching_meta_pte = v->htotal[k] / v->pixel_clock[k] / 4.0;
+				}
+				v->destination_lines_to_request_vm_inv_blank[k] =dcn_bw_floor2(4.0 * (v->time_for_fetching_meta_pte / (v->htotal[k] / v->pixel_clock[k]) + 0.125), 1.0) / 4;
+				if ((v->pte_enable == dcn_bw_yes || v->dcc_enable[k] == dcn_bw_yes)) {
+					if (v->immediate_flip_supported == dcn_bw_yes && (v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+						v->time_for_fetching_row_in_vblank =dcn_bw_max5((v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k]) / v->prefetch_bandwidth[k], (v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k]) * v->tot_immediate_flip_bytes / (v->bandwidth_available_for_immediate_flip * (v->meta_pte_bytes_frame[k] + v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k])), v->urgent_extra_latency, 2.0 * v->urgent_latency, v->htotal[k] / v->pixel_clock[k] - v->time_for_fetching_meta_pte);
+					}
+					else {
+						v->time_for_fetching_row_in_vblank =dcn_bw_max3((v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k]) / v->prefetch_bandwidth[k], v->urgent_extra_latency, v->htotal[k] / v->pixel_clock[k] - v->time_for_fetching_meta_pte);
+					}
+				}
+				else {
+					v->time_for_fetching_row_in_vblank =dcn_bw_max2(v->urgent_extra_latency - v->time_for_fetching_meta_pte, v->htotal[k] / v->pixel_clock[k] - v->time_for_fetching_meta_pte);
+				}
+				v->destination_lines_to_request_row_in_vblank[k] =dcn_bw_floor2(4.0 * (v->time_for_fetching_row_in_vblank / (v->htotal[k] / v->pixel_clock[k]) + 0.125), 1.0) / 4;
+				v->lines_to_request_prefetch_pixel_data = v->destination_lines_for_prefetch[k] - v->destination_lines_to_request_vm_inv_blank[k] - v->destination_lines_to_request_row_in_vblank[k];
+				if (v->lines_to_request_prefetch_pixel_data > 0.0) {
+					v->v_ratio_prefetch_y[k] = v->prefetch_source_lines_y[k] / v->lines_to_request_prefetch_pixel_data;
+					if ((v->swath_height_y[k] > 4.0)) {
+						if (v->lines_to_request_prefetch_pixel_data > (v->v_init_pre_fill_y[k] - 3.0) / 2.0) {
+							v->v_ratio_prefetch_y[k] =dcn_bw_max2(v->v_ratio_prefetch_y[k], v->max_num_swath_y[k] * v->swath_height_y[k] / (v->lines_to_request_prefetch_pixel_data - (v->v_init_pre_fill_y[k] - 3.0) / 2.0));
+						}
+						else {
+							v->v_ratio_prefetch_y[k] = 999999.0;
+						}
+					}
+				}
+				else {
+					v->v_ratio_prefetch_y[k] = 999999.0;
+				}
+				v->v_ratio_prefetch_y[k] =dcn_bw_max2(v->v_ratio_prefetch_y[k], 1.0);
+				if (v->lines_to_request_prefetch_pixel_data > 0.0) {
+					v->v_ratio_prefetch_c[k] = v->prefetch_source_lines_c[k] / v->lines_to_request_prefetch_pixel_data;
+					if ((v->swath_height_c[k] > 4.0)) {
+						if (v->lines_to_request_prefetch_pixel_data > (v->v_init_pre_fill_c[k] - 3.0) / 2.0) {
+							v->v_ratio_prefetch_c[k] =dcn_bw_max2(v->v_ratio_prefetch_c[k], v->max_num_swath_c[k] * v->swath_height_c[k] / (v->lines_to_request_prefetch_pixel_data - (v->v_init_pre_fill_c[k] - 3.0) / 2.0));
+						}
+						else {
+							v->v_ratio_prefetch_c[k] = 999999.0;
+						}
+					}
+				}
+				else {
+					v->v_ratio_prefetch_c[k] = 999999.0;
+				}
+				v->v_ratio_prefetch_c[k] =dcn_bw_max2(v->v_ratio_prefetch_c[k], 1.0);
+				if (v->lines_to_request_prefetch_pixel_data > 0.0) {
+					v->required_prefetch_pix_data_bw = v->dpp_per_plane[k] * (v->prefetch_source_lines_y[k] / v->lines_to_request_prefetch_pixel_data *dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) + v->prefetch_source_lines_c[k] / v->lines_to_request_prefetch_pixel_data *dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / 2.0) * v->swath_width_y[k] / (v->htotal[k] / v->pixel_clock[k]);
+				}
+				else {
+					v->required_prefetch_pix_data_bw = 999999.0;
+				}
+				v->max_rd_bandwidth = v->max_rd_bandwidth +dcn_bw_max2(v->read_bandwidth_plane_luma[k] + v->read_bandwidth_plane_chroma[k], v->required_prefetch_pix_data_bw);
+				if (v->immediate_flip_supported == dcn_bw_yes && (v->source_pixel_format[k] != dcn_bw_yuv420_sub_8 && v->source_pixel_format[k] != dcn_bw_yuv420_sub_10)) {
+					v->max_rd_bandwidth = v->max_rd_bandwidth +dcn_bw_max2(v->meta_pte_bytes_frame[k] / (v->destination_lines_to_request_vm_inv_blank[k] * v->htotal[k] / v->pixel_clock[k]), (v->meta_row_byte[k] + v->pixel_pte_bytes_per_row[k]) / (v->destination_lines_to_request_row_in_vblank[k] * v->htotal[k] / v->pixel_clock[k]));
+				}
+				if (v->v_ratio_prefetch_y[k] > 4.0 || v->v_ratio_prefetch_c[k] > 4.0) {
+					v->v_ratio_prefetch_more_than4 = dcn_bw_yes;
+				}
+				if (v->destination_lines_for_prefetch[k] < 2.0) {
+					v->destination_line_times_for_prefetch_less_than2 = dcn_bw_yes;
+				}
+				if (v->max_vstartup_lines[k] > v->v_startup_lines) {
+					if (v->required_prefetch_pix_data_bw > (v->read_bandwidth_plane_luma[k] + v->read_bandwidth_plane_chroma[k])) {
+						v->planes_with_room_to_increase_vstartup_prefetch_bw_less_than_active_bw = dcn_bw_no;
+					}
+					if (v->v_ratio_prefetch_y[k] > 4.0 || v->v_ratio_prefetch_c[k] > 4.0) {
+						v->planes_with_room_to_increase_vstartup_vratio_prefetch_more_than4 = dcn_bw_yes;
+					}
+					if (v->destination_lines_for_prefetch[k] < 2.0) {
+						v->planes_with_room_to_increase_vstartup_destination_line_times_for_prefetch_less_than2 = dcn_bw_yes;
+					}
+				}
+			}
+			if (v->max_rd_bandwidth <= v->return_bw && v->v_ratio_prefetch_more_than4 == dcn_bw_no && v->destination_line_times_for_prefetch_less_than2 == dcn_bw_no) {
+				v->prefetch_mode_supported = dcn_bw_yes;
+			}
+			else {
+				v->prefetch_mode_supported = dcn_bw_no;
+			}
+			v->v_startup_lines = v->v_startup_lines + 1.0;
+		} while (!(v->prefetch_mode_supported == dcn_bw_yes || (v->planes_with_room_to_increase_vstartup_prefetch_bw_less_than_active_bw == dcn_bw_yes && v->planes_with_room_to_increase_vstartup_vratio_prefetch_more_than4 == dcn_bw_no && v->planes_with_room_to_increase_vstartup_destination_line_times_for_prefetch_less_than2 == dcn_bw_no)));
+		v->next_prefetch_mode = v->next_prefetch_mode + 1.0;
+	} while (!(v->prefetch_mode_supported == dcn_bw_yes || v->prefetch_mode == 2.0));
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->v_ratio_prefetch_y[k] <= 1.0) {
+			v->display_pipe_line_delivery_time_luma_prefetch[k] = v->swath_width_y[k] * v->dpp_per_plane[k] / v->h_ratio[k] / v->pixel_clock[k];
+		}
+		else {
+			v->display_pipe_line_delivery_time_luma_prefetch[k] = v->swath_width_y[k] / v->pscl_throughput[k] / v->dppclk;
+		}
+		if (v->byte_per_pixel_detc[k] == 0.0) {
+			v->display_pipe_line_delivery_time_chroma_prefetch[k] = 0.0;
+		}
+		else {
+			if (v->v_ratio_prefetch_c[k] <= 1.0) {
+				v->display_pipe_line_delivery_time_chroma_prefetch[k] = v->swath_width_y[k] * v->dpp_per_plane[k] / v->h_ratio[k] / v->pixel_clock[k];
+			}
+			else {
+				v->display_pipe_line_delivery_time_chroma_prefetch[k] = v->swath_width_y[k] / v->pscl_throughput[k] / v->dppclk;
+			}
+		}
+	}
+	/*min ttuv_blank*/
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->prefetch_mode == 0.0) {
+			v->allow_dram_clock_change_during_vblank[k] = dcn_bw_yes;
+			v->allow_dram_self_refresh_during_vblank[k] = dcn_bw_yes;
+			v->min_ttuv_blank[k] = v->t_calc +dcn_bw_max3(v->dram_clock_change_watermark, v->stutter_enter_plus_exit_watermark, v->urgent_watermark);
+		}
+		else if (v->prefetch_mode == 1.0) {
+			v->allow_dram_clock_change_during_vblank[k] = dcn_bw_no;
+			v->allow_dram_self_refresh_during_vblank[k] = dcn_bw_yes;
+			v->min_ttuv_blank[k] = v->t_calc +dcn_bw_max2(v->stutter_enter_plus_exit_watermark, v->urgent_watermark);
+		}
+		else {
+			v->allow_dram_clock_change_during_vblank[k] = dcn_bw_no;
+			v->allow_dram_self_refresh_during_vblank[k] = dcn_bw_no;
+			v->min_ttuv_blank[k] = v->t_calc + v->urgent_watermark;
+		}
+	}
+	/*nb p-state/dram clock change support*/
+
+	v->active_dp_ps = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->active_dp_ps = v->active_dp_ps + v->dpp_per_plane[k];
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->lb_latency_hiding_source_lines_y =dcn_bw_min2(v->max_line_buffer_lines,dcn_bw_floor2(v->line_buffer_size / v->lb_bit_per_pixel[k] / (v->swath_width_y[k] /dcn_bw_max2(v->h_ratio[k], 1.0)), 1.0)) - (v->vtaps[k] - 1.0);
+		v->lb_latency_hiding_source_lines_c =dcn_bw_min2(v->max_line_buffer_lines,dcn_bw_floor2(v->line_buffer_size / v->lb_bit_per_pixel[k] / (v->swath_width_y[k] / 2.0 /dcn_bw_max2(v->h_ratio[k] / 2.0, 1.0)), 1.0)) - (v->vta_pschroma[k] - 1.0);
+		v->effective_lb_latency_hiding_y = v->lb_latency_hiding_source_lines_y / v->v_ratio[k] * (v->htotal[k] / v->pixel_clock[k]);
+		v->effective_lb_latency_hiding_c = v->lb_latency_hiding_source_lines_c / (v->v_ratio[k] / 2.0) * (v->htotal[k] / v->pixel_clock[k]);
+		if (v->swath_width_y[k] > 2.0 * v->dpp_output_buffer_pixels) {
+			v->dpp_output_buffer_lines_y = v->dpp_output_buffer_pixels / v->swath_width_y[k];
+		}
+		else if (v->swath_width_y[k] > v->dpp_output_buffer_pixels) {
+			v->dpp_output_buffer_lines_y = 0.5;
+		}
+		else {
+			v->dpp_output_buffer_lines_y = 1.0;
+		}
+		if (v->swath_width_y[k] / 2.0 > 2.0 * v->dpp_output_buffer_pixels) {
+			v->dpp_output_buffer_lines_c = v->dpp_output_buffer_pixels / (v->swath_width_y[k] / 2.0);
+		}
+		else if (v->swath_width_y[k] / 2.0 > v->dpp_output_buffer_pixels) {
+			v->dpp_output_buffer_lines_c = 0.5;
+		}
+		else {
+			v->dpp_output_buffer_lines_c = 1.0;
+		}
+		v->dppopp_buffering_y = (v->htotal[k] / v->pixel_clock[k]) * (v->dpp_output_buffer_lines_y + v->opp_output_buffer_lines);
+		v->max_det_buffering_time_y = v->full_det_buffering_time_y[k] + (v->lines_in_dety[k] - v->lines_in_dety_rounded_down_to_swath[k]) / v->swath_height_y[k] * (v->htotal[k] / v->pixel_clock[k]);
+		v->active_dram_clock_change_latency_margin_y = v->dppopp_buffering_y + v->effective_lb_latency_hiding_y + v->max_det_buffering_time_y - v->dram_clock_change_watermark;
+		if (v->active_dp_ps > 1.0) {
+			v->active_dram_clock_change_latency_margin_y = v->active_dram_clock_change_latency_margin_y - (1.0 - 1.0 / (v->active_dp_ps - 1.0)) * v->swath_height_y[k] * (v->htotal[k] / v->pixel_clock[k]);
+		}
+		if (v->byte_per_pixel_detc[k] > 0.0) {
+			v->dppopp_buffering_c = (v->htotal[k] / v->pixel_clock[k]) * (v->dpp_output_buffer_lines_c + v->opp_output_buffer_lines);
+			v->max_det_buffering_time_c = v->full_det_buffering_time_c[k] + (v->lines_in_detc[k] - v->lines_in_detc_rounded_down_to_swath[k]) / v->swath_height_c[k] * (v->htotal[k] / v->pixel_clock[k]);
+			v->active_dram_clock_change_latency_margin_c = v->dppopp_buffering_c + v->effective_lb_latency_hiding_c + v->max_det_buffering_time_c - v->dram_clock_change_watermark;
+			if (v->active_dp_ps > 1.0) {
+				v->active_dram_clock_change_latency_margin_c = v->active_dram_clock_change_latency_margin_c - (1.0 - 1.0 / (v->active_dp_ps - 1.0)) * v->swath_height_c[k] * (v->htotal[k] / v->pixel_clock[k]);
+			}
+			v->active_dram_clock_change_latency_margin[k] =dcn_bw_min2(v->active_dram_clock_change_latency_margin_y, v->active_dram_clock_change_latency_margin_c);
+		}
+		else {
+			v->active_dram_clock_change_latency_margin[k] = v->active_dram_clock_change_latency_margin_y;
+		}
+		if (v->output_format[k] == dcn_bw_444) {
+			v->writeback_dram_clock_change_latency_margin = (v->writeback_luma_buffer_size + v->writeback_chroma_buffer_size) * 1024.0 / (v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) * 4.0) - v->writeback_dram_clock_change_watermark;
+		}
+		else {
+			v->writeback_dram_clock_change_latency_margin =dcn_bw_min2(v->writeback_luma_buffer_size, 2.0 * v->writeback_chroma_buffer_size) * 1024.0 / (v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k])) - v->writeback_dram_clock_change_watermark;
+		}
+		if (v->output[k] == dcn_bw_writeback) {
+			v->active_dram_clock_change_latency_margin[k] =dcn_bw_min2(v->active_dram_clock_change_latency_margin[k], v->writeback_dram_clock_change_latency_margin);
+		}
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->allow_dram_clock_change_during_vblank[k] == dcn_bw_yes) {
+			v->v_blank_dram_clock_change_latency_margin[k] = (v->vtotal[k] - v->scaler_recout_height[k]) * (v->htotal[k] / v->pixel_clock[k]) -dcn_bw_max2(v->dram_clock_change_watermark, v->writeback_dram_clock_change_watermark);
+		}
+		else {
+			v->v_blank_dram_clock_change_latency_margin[k] = 0.0;
+		}
+	}
+	v->min_active_dram_clock_change_margin = 999999.0;
+	v->v_blank_of_min_active_dram_clock_change_margin = 999999.0;
+	v->second_min_active_dram_clock_change_margin = 999999.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->active_dram_clock_change_latency_margin[k] < v->min_active_dram_clock_change_margin) {
+			v->second_min_active_dram_clock_change_margin = v->min_active_dram_clock_change_margin;
+			v->min_active_dram_clock_change_margin = v->active_dram_clock_change_latency_margin[k];
+			v->v_blank_of_min_active_dram_clock_change_margin = v->v_blank_dram_clock_change_latency_margin[k];
+		}
+		else if (v->active_dram_clock_change_latency_margin[k] < v->second_min_active_dram_clock_change_margin) {
+			v->second_min_active_dram_clock_change_margin = v->active_dram_clock_change_latency_margin[k];
+		}
+	}
+	v->min_vblank_dram_clock_change_margin = 999999.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->min_vblank_dram_clock_change_margin > v->v_blank_dram_clock_change_latency_margin[k]) {
+			v->min_vblank_dram_clock_change_margin = v->v_blank_dram_clock_change_latency_margin[k];
+		}
+	}
+	if (v->synchronized_vblank == dcn_bw_yes || v->number_of_active_planes == 1) {
+		v->dram_clock_change_margin =dcn_bw_max2(v->min_active_dram_clock_change_margin, v->min_vblank_dram_clock_change_margin);
+	}
+	else if (v->v_blank_of_min_active_dram_clock_change_margin > v->min_active_dram_clock_change_margin) {
+		v->dram_clock_change_margin =dcn_bw_min2(v->second_min_active_dram_clock_change_margin, v->v_blank_of_min_active_dram_clock_change_margin);
+	}
+	else {
+		v->dram_clock_change_margin = v->min_active_dram_clock_change_margin;
+	}
+	if (v->min_active_dram_clock_change_margin > 0.0) {
+		v->dram_clock_change_support = dcn_bw_supported_in_v_active;
+	}
+	else if (v->dram_clock_change_margin > 0.0) {
+		v->dram_clock_change_support = dcn_bw_supported_in_v_blank;
+	}
+	else {
+		v->dram_clock_change_support = dcn_bw_not_supported;
+	}
+	/*maximum bandwidth used*/
+
+	v->wr_bandwidth = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->output[k] == dcn_bw_writeback && v->output_format[k] == dcn_bw_444) {
+			v->wr_bandwidth = v->wr_bandwidth + v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) * 4.0;
+		}
+		else if (v->output[k] == dcn_bw_writeback) {
+			v->wr_bandwidth = v->wr_bandwidth + v->scaler_rec_out_width[k] / (v->htotal[k] / v->pixel_clock[k]) * 1.5;
+		}
+	}
+	v->max_used_bw = v->max_rd_bandwidth + v->wr_bandwidth;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calc_auto.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calc_auto.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright 2017 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#ifndef _DCN_CALC_AUTO_H_
+#define _DCN_CALC_AUTO_H_
+
+#include "dc.h"
+#include "dcn_calcs.h"
+
+void scaler_settings_calculation(struct dcn_bw_internal_vars *v);
+void mode_support_and_system_configuration(struct dcn_bw_internal_vars *v);
+void display_pipe_configuration(struct dcn_bw_internal_vars *v);
+void dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(
+		struct dcn_bw_internal_vars *v);
+
+#endif /* _DCN_CALC_AUTO_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calc_math.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calc_math.c
@@ -0,0 +1,147 @@
+/*
+ * Copyright 2017 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include "dcn_calc_math.h"
+
+#define isNaN(number) ((number) != (number))
+
+/*
+ * NOTE:
+ *   This file is gcc-parseable HW gospel, coming straight from HW engineers.
+ *
+ * It doesn't adhere to Linux kernel style and sometimes will do things in odd
+ * ways. Unless there is something clearly wrong with it the code should
+ * remain as-is as it provides us with a guarantee from HW that it is correct.
+ */
+
+float dcn_bw_mod(const float arg1, const float arg2)
+{
+	if (isNaN(arg1))
+		return arg2;
+	if (isNaN(arg2))
+		return arg1;
+	return arg1 - arg1 * ((int) (arg1 / arg2));
+}
+
+float dcn_bw_min2(const float arg1, const float arg2)
+{
+	if (isNaN(arg1))
+		return arg2;
+	if (isNaN(arg2))
+		return arg1;
+	return arg1 < arg2 ? arg1 : arg2;
+}
+
+unsigned int dcn_bw_max(const unsigned int arg1, const unsigned int arg2)
+{
+	return arg1 > arg2 ? arg1 : arg2;
+}
+float dcn_bw_max2(const float arg1, const float arg2)
+{
+	if (isNaN(arg1))
+		return arg2;
+	if (isNaN(arg2))
+		return arg1;
+	return arg1 > arg2 ? arg1 : arg2;
+}
+
+float dcn_bw_floor2(const float arg, const float significance)
+{
+	if (significance == 0)
+		return 0;
+	return ((int) (arg / significance)) * significance;
+}
+float dcn_bw_floor(const float arg)
+{
+	return ((int) (arg));
+}
+
+float dcn_bw_ceil(const float arg)
+{
+	float flr = dcn_bw_floor2(arg, 1);
+
+	return flr + 0.00001 >= arg ? arg : flr + 1;
+}
+
+float dcn_bw_ceil2(const float arg, const float significance)
+{
+	float flr = dcn_bw_floor2(arg, significance);
+	if (significance == 0)
+		return 0;
+	return flr + 0.00001 >= arg ? arg : flr + significance;
+}
+
+float dcn_bw_max3(float v1, float v2, float v3)
+{
+	return v3 > dcn_bw_max2(v1, v2) ? v3 : dcn_bw_max2(v1, v2);
+}
+
+float dcn_bw_max5(float v1, float v2, float v3, float v4, float v5)
+{
+	return dcn_bw_max3(v1, v2, v3) > dcn_bw_max2(v4, v5) ? dcn_bw_max3(v1, v2, v3) : dcn_bw_max2(v4, v5);
+}
+
+float dcn_bw_pow(float a, float exp)
+{
+	float temp;
+	/*ASSERT(exp == (int)exp);*/
+	if ((int)exp == 0)
+		return 1;
+	temp = dcn_bw_pow(a, (int)(exp / 2));
+	if (((int)exp % 2) == 0) {
+		return temp * temp;
+	} else {
+		if ((int)exp > 0)
+			return a * temp * temp;
+		else
+			return (temp * temp) / a;
+	}
+}
+
+double dcn_bw_fabs(double a)
+{
+	if (a > 0)
+		return (a);
+	else
+		return (-a);
+}
+
+
+float dcn_bw_log(float a, float b)
+{
+	int * const exp_ptr = (int *)(&a);
+	int x = *exp_ptr;
+	const int log_2 = ((x >> 23) & 255) - 128;
+	x &= ~(255 << 23);
+	x += 127 << 23;
+	*exp_ptr = x;
+
+	a = ((-1.0f / 3) * a + 2) * a - 2.0f / 3;
+
+	if (b > 2.00001 || b < 1.99999)
+		return (a + log_2) / dcn_bw_log(b, 2);
+	else
+		return (a + log_2);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calcs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/calcs/dcn_calcs.c
@@ -0,0 +1,1803 @@
+/*
+ * Copyright 2017 Advanced Micro Devices, Inc.
+ * Copyright 2019 Raptor Engineering, LLC
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include "dm_services.h"
+#include "dc.h"
+#include "dcn_calcs.h"
+#include "dcn_calc_auto.h"
+#include "dal_asic_id.h"
+#include "resource.h"
+#include "dcn10/dcn10_resource.h"
+#include "dcn10/dcn10_hubbub.h"
+#include "dml/dml1_display_rq_dlg_calc.h"
+
+#include "dcn_calc_math.h"
+
+#define DC_LOGGER \
+	dc->ctx->logger
+
+#define WM_SET_COUNT 4
+#define WM_A 0
+#define WM_B 1
+#define WM_C 2
+#define WM_D 3
+
+/*
+ * NOTE:
+ *   This file is gcc-parseable HW gospel, coming straight from HW engineers.
+ *
+ * It doesn't adhere to Linux kernel style and sometimes will do things in odd
+ * ways. Unless there is something clearly wrong with it the code should
+ * remain as-is as it provides us with a guarantee from HW that it is correct.
+ */
+
+/* Defaults from spreadsheet rev#247.
+ * RV2 delta: dram_clock_change_latency, max_num_dpp
+ */
+const struct dcn_soc_bounding_box dcn10_soc_defaults = {
+		/* latencies */
+		.sr_exit_time = 17, /*us*/
+		.sr_enter_plus_exit_time = 19, /*us*/
+		.urgent_latency = 4, /*us*/
+		.dram_clock_change_latency = 17, /*us*/
+		.write_back_latency = 12, /*us*/
+		.percent_of_ideal_drambw_received_after_urg_latency = 80, /*%*/
+
+		/* below default clocks derived from STA target base on
+		 * slow-slow corner + 10% margin with voltages aligned to FCLK.
+		 *
+		 * Use these value if fused value doesn't make sense as earlier
+		 * part don't have correct value fused */
+		/* default DCF CLK DPM on RV*/
+		.dcfclkv_max0p9 = 655,	/* MHz, = 3600/5.5 */
+		.dcfclkv_nom0p8 = 626,	/* MHz, = 3600/5.75 */
+		.dcfclkv_mid0p72 = 600,	/* MHz, = 3600/6, bypass */
+		.dcfclkv_min0p65 = 300,	/* MHz, = 3600/12, bypass */
+
+		/* default DISP CLK voltage state on RV */
+		.max_dispclk_vmax0p9 = 1108,	/* MHz, = 3600/3.25 */
+		.max_dispclk_vnom0p8 = 1029,	/* MHz, = 3600/3.5 */
+		.max_dispclk_vmid0p72 = 960,	/* MHz, = 3600/3.75 */
+		.max_dispclk_vmin0p65 = 626,	/* MHz, = 3600/5.75 */
+
+		/* default DPP CLK voltage state on RV */
+		.max_dppclk_vmax0p9 = 720,	/* MHz, = 3600/5 */
+		.max_dppclk_vnom0p8 = 686,	/* MHz, = 3600/5.25 */
+		.max_dppclk_vmid0p72 = 626,	/* MHz, = 3600/5.75 */
+		.max_dppclk_vmin0p65 = 400,	/* MHz, = 3600/9 */
+
+		/* default PHY CLK voltage state on RV */
+		.phyclkv_max0p9 = 900, /*MHz*/
+		.phyclkv_nom0p8 = 847, /*MHz*/
+		.phyclkv_mid0p72 = 800, /*MHz*/
+		.phyclkv_min0p65 = 600, /*MHz*/
+
+		/* BW depend on FCLK, MCLK, # of channels */
+		/* dual channel BW */
+		.fabric_and_dram_bandwidth_vmax0p9 = 38.4f, /*GB/s*/
+		.fabric_and_dram_bandwidth_vnom0p8 = 34.133f, /*GB/s*/
+		.fabric_and_dram_bandwidth_vmid0p72 = 29.866f, /*GB/s*/
+		.fabric_and_dram_bandwidth_vmin0p65 = 12.8f, /*GB/s*/
+		/* single channel BW
+		.fabric_and_dram_bandwidth_vmax0p9 = 19.2f,
+		.fabric_and_dram_bandwidth_vnom0p8 = 17.066f,
+		.fabric_and_dram_bandwidth_vmid0p72 = 14.933f,
+		.fabric_and_dram_bandwidth_vmin0p65 = 12.8f,
+		*/
+
+		.number_of_channels = 2,
+
+		.socclk = 208, /*MHz*/
+		.downspreading = 0.5f, /*%*/
+		.round_trip_ping_latency_cycles = 128, /*DCFCLK Cycles*/
+		.urgent_out_of_order_return_per_channel = 256, /*bytes*/
+		.vmm_page_size = 4096, /*bytes*/
+		.return_bus_width = 64, /*bytes*/
+		.max_request_size = 256, /*bytes*/
+
+		/* Depends on user class (client vs embedded, workstation, etc) */
+		.percent_disp_bw_limit = 0.3f /*%*/
+};
+
+const struct dcn_ip_params dcn10_ip_defaults = {
+		.rob_buffer_size_in_kbyte = 64,
+		.det_buffer_size_in_kbyte = 164,
+		.dpp_output_buffer_pixels = 2560,
+		.opp_output_buffer_lines = 1,
+		.pixel_chunk_size_in_kbyte = 8,
+		.pte_enable = dcn_bw_yes,
+		.pte_chunk_size = 2, /*kbytes*/
+		.meta_chunk_size = 2, /*kbytes*/
+		.writeback_chunk_size = 2, /*kbytes*/
+		.odm_capability = dcn_bw_no,
+		.dsc_capability = dcn_bw_no,
+		.line_buffer_size = 589824, /*bit*/
+		.max_line_buffer_lines = 12,
+		.is_line_buffer_bpp_fixed = dcn_bw_no,
+		.line_buffer_fixed_bpp = dcn_bw_na,
+		.writeback_luma_buffer_size = 12, /*kbytes*/
+		.writeback_chroma_buffer_size = 8, /*kbytes*/
+		.max_num_dpp = 4,
+		.max_num_writeback = 2,
+		.max_dchub_topscl_throughput = 4, /*pixels/dppclk*/
+		.max_pscl_tolb_throughput = 2, /*pixels/dppclk*/
+		.max_lb_tovscl_throughput = 4, /*pixels/dppclk*/
+		.max_vscl_tohscl_throughput = 4, /*pixels/dppclk*/
+		.max_hscl_ratio = 4,
+		.max_vscl_ratio = 4,
+		.max_hscl_taps = 8,
+		.max_vscl_taps = 8,
+		.pte_buffer_size_in_requests = 42,
+		.dispclk_ramping_margin = 1, /*%*/
+		.under_scan_factor = 1.11f,
+		.max_inter_dcn_tile_repeaters = 8,
+		.can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one = dcn_bw_no,
+		.bug_forcing_luma_and_chroma_request_to_same_size_fixed = dcn_bw_no,
+		.dcfclk_cstate_latency = 10 /*TODO clone of something else? sr_enter_plus_exit_time?*/
+};
+
+static enum dcn_bw_defs tl_sw_mode_to_bw_defs(enum swizzle_mode_values sw_mode)
+{
+	switch (sw_mode) {
+	case DC_SW_LINEAR:
+		return dcn_bw_sw_linear;
+	case DC_SW_4KB_S:
+		return dcn_bw_sw_4_kb_s;
+	case DC_SW_4KB_D:
+		return dcn_bw_sw_4_kb_d;
+	case DC_SW_64KB_S:
+		return dcn_bw_sw_64_kb_s;
+	case DC_SW_64KB_D:
+		return dcn_bw_sw_64_kb_d;
+	case DC_SW_VAR_S:
+		return dcn_bw_sw_var_s;
+	case DC_SW_VAR_D:
+		return dcn_bw_sw_var_d;
+	case DC_SW_64KB_S_T:
+		return dcn_bw_sw_64_kb_s_t;
+	case DC_SW_64KB_D_T:
+		return dcn_bw_sw_64_kb_d_t;
+	case DC_SW_4KB_S_X:
+		return dcn_bw_sw_4_kb_s_x;
+	case DC_SW_4KB_D_X:
+		return dcn_bw_sw_4_kb_d_x;
+	case DC_SW_64KB_S_X:
+		return dcn_bw_sw_64_kb_s_x;
+	case DC_SW_64KB_D_X:
+		return dcn_bw_sw_64_kb_d_x;
+	case DC_SW_VAR_S_X:
+		return dcn_bw_sw_var_s_x;
+	case DC_SW_VAR_D_X:
+		return dcn_bw_sw_var_d_x;
+	case DC_SW_256B_S:
+	case DC_SW_256_D:
+	case DC_SW_256_R:
+	case DC_SW_4KB_R:
+	case DC_SW_64KB_R:
+	case DC_SW_VAR_R:
+	case DC_SW_4KB_R_X:
+	case DC_SW_64KB_R_X:
+	case DC_SW_VAR_R_X:
+	default:
+		BREAK_TO_DEBUGGER(); /*not in formula*/
+		return dcn_bw_sw_4_kb_s;
+	}
+}
+
+static int tl_lb_bpp_to_int(enum lb_pixel_depth depth)
+{
+	switch (depth) {
+	case LB_PIXEL_DEPTH_18BPP:
+		return 18;
+	case LB_PIXEL_DEPTH_24BPP:
+		return 24;
+	case LB_PIXEL_DEPTH_30BPP:
+		return 30;
+	case LB_PIXEL_DEPTH_36BPP:
+		return 36;
+	default:
+		return 30;
+	}
+}
+
+static enum dcn_bw_defs tl_pixel_format_to_bw_defs(enum surface_pixel_format format)
+{
+	switch (format) {
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB1555:
+	case SURFACE_PIXEL_FORMAT_GRPH_RGB565:
+		return dcn_bw_rgb_sub_16;
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB8888:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR8888:
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB2101010:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR2101010:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR2101010_XR_BIAS:
+		return dcn_bw_rgb_sub_32;
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616:
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616F:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616F:
+		return dcn_bw_rgb_sub_64;
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_YCbCr:
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_YCrCb:
+		return dcn_bw_yuv420_sub_8;
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCbCr:
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCrCb:
+		return dcn_bw_yuv420_sub_10;
+	default:
+		return dcn_bw_rgb_sub_32;
+	}
+}
+
+enum source_macro_tile_size swizzle_mode_to_macro_tile_size(enum swizzle_mode_values sw_mode)
+{
+	switch (sw_mode) {
+	/* for 4/8/16 high tiles */
+	case DC_SW_LINEAR:
+		return dm_4k_tile;
+	case DC_SW_4KB_S:
+	case DC_SW_4KB_S_X:
+		return dm_4k_tile;
+	case DC_SW_64KB_S:
+	case DC_SW_64KB_S_X:
+	case DC_SW_64KB_S_T:
+		return dm_64k_tile;
+	case DC_SW_VAR_S:
+	case DC_SW_VAR_S_X:
+		return dm_256k_tile;
+
+	/* For 64bpp 2 high tiles */
+	case DC_SW_4KB_D:
+	case DC_SW_4KB_D_X:
+		return dm_4k_tile;
+	case DC_SW_64KB_D:
+	case DC_SW_64KB_D_X:
+	case DC_SW_64KB_D_T:
+		return dm_64k_tile;
+	case DC_SW_VAR_D:
+	case DC_SW_VAR_D_X:
+		return dm_256k_tile;
+
+	case DC_SW_4KB_R:
+	case DC_SW_4KB_R_X:
+		return dm_4k_tile;
+	case DC_SW_64KB_R:
+	case DC_SW_64KB_R_X:
+		return dm_64k_tile;
+	case DC_SW_VAR_R:
+	case DC_SW_VAR_R_X:
+		return dm_256k_tile;
+
+	/* Unsupported swizzle modes for dcn */
+	case DC_SW_256B_S:
+	default:
+		ASSERT(0); /* Not supported */
+		return 0;
+	}
+}
+
+static void pipe_ctx_to_e2e_pipe_params (
+		const struct pipe_ctx *pipe,
+		struct _vcs_dpi_display_pipe_params_st *input)
+{
+	input->src.is_hsplit = false;
+
+	/* stereo can never be split */
+	if (pipe->plane_state->stereo_format == PLANE_STEREO_FORMAT_SIDE_BY_SIDE ||
+	    pipe->plane_state->stereo_format == PLANE_STEREO_FORMAT_TOP_AND_BOTTOM) {
+		/* reset the split group if it was already considered split. */
+		input->src.hsplit_grp = pipe->pipe_idx;
+	} else if (pipe->top_pipe != NULL && pipe->top_pipe->plane_state == pipe->plane_state) {
+		input->src.is_hsplit = true;
+	} else if (pipe->bottom_pipe != NULL && pipe->bottom_pipe->plane_state == pipe->plane_state) {
+		input->src.is_hsplit = true;
+	}
+
+	if (pipe->plane_res.dpp->ctx->dc->debug.optimized_watermark) {
+		/*
+		 * this method requires us to always re-calculate watermark when dcc change
+		 * between flip.
+		 */
+		input->src.dcc = pipe->plane_state->dcc.enable ? 1 : 0;
+	} else {
+		/*
+		 * allow us to disable dcc on the fly without re-calculating WM
+		 *
+		 * extra overhead for DCC is quite small.  for 1080p WM without
+		 * DCC is only 0.417us lower (urgent goes from 6.979us to 6.562us)
+		 */
+		unsigned int bpe;
+
+		input->src.dcc = pipe->plane_res.dpp->ctx->dc->res_pool->hubbub->funcs->
+			dcc_support_pixel_format(pipe->plane_state->format, &bpe) ? 1 : 0;
+	}
+	input->src.dcc_rate            = 1;
+	input->src.meta_pitch          = pipe->plane_state->dcc.meta_pitch;
+	input->src.source_scan         = dm_horz;
+	input->src.sw_mode             = pipe->plane_state->tiling_info.gfx9.swizzle;
+
+	input->src.viewport_width      = pipe->plane_res.scl_data.viewport.width;
+	input->src.viewport_height     = pipe->plane_res.scl_data.viewport.height;
+	input->src.data_pitch          = pipe->plane_res.scl_data.viewport.width;
+	input->src.data_pitch_c        = pipe->plane_res.scl_data.viewport.width;
+	input->src.cur0_src_width      = 128; /* TODO: Cursor calcs, not curently stored */
+	input->src.cur0_bpp            = 32;
+
+	input->src.macro_tile_size = swizzle_mode_to_macro_tile_size(pipe->plane_state->tiling_info.gfx9.swizzle);
+
+	switch (pipe->plane_state->rotation) {
+	case ROTATION_ANGLE_0:
+	case ROTATION_ANGLE_180:
+		input->src.source_scan = dm_horz;
+		break;
+	case ROTATION_ANGLE_90:
+	case ROTATION_ANGLE_270:
+		input->src.source_scan = dm_vert;
+		break;
+	default:
+		ASSERT(0); /* Not supported */
+		break;
+	}
+
+	/* TODO: Fix pixel format mappings */
+	switch (pipe->plane_state->format) {
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_YCbCr:
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_YCrCb:
+		input->src.source_format = dm_420_8;
+		input->src.viewport_width_c    = input->src.viewport_width / 2;
+		input->src.viewport_height_c   = input->src.viewport_height / 2;
+		break;
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCbCr:
+	case SURFACE_PIXEL_FORMAT_VIDEO_420_10bpc_YCrCb:
+		input->src.source_format = dm_420_10;
+		input->src.viewport_width_c    = input->src.viewport_width / 2;
+		input->src.viewport_height_c   = input->src.viewport_height / 2;
+		break;
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616:
+	case SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616F:
+	case SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616F:
+		input->src.source_format = dm_444_64;
+		input->src.viewport_width_c    = input->src.viewport_width;
+		input->src.viewport_height_c   = input->src.viewport_height;
+		break;
+	case SURFACE_PIXEL_FORMAT_GRPH_RGBE_ALPHA:
+		input->src.source_format = dm_rgbe_alpha;
+		input->src.viewport_width_c    = input->src.viewport_width;
+		input->src.viewport_height_c   = input->src.viewport_height;
+		break;
+	default:
+		input->src.source_format = dm_444_32;
+		input->src.viewport_width_c    = input->src.viewport_width;
+		input->src.viewport_height_c   = input->src.viewport_height;
+		break;
+	}
+
+	input->scale_taps.htaps                = pipe->plane_res.scl_data.taps.h_taps;
+	input->scale_ratio_depth.hscl_ratio    = pipe->plane_res.scl_data.ratios.horz.value/4294967296.0;
+	input->scale_ratio_depth.vscl_ratio    = pipe->plane_res.scl_data.ratios.vert.value/4294967296.0;
+	input->scale_ratio_depth.vinit =  pipe->plane_res.scl_data.inits.v.value/4294967296.0;
+	if (input->scale_ratio_depth.vinit < 1.0)
+			input->scale_ratio_depth.vinit = 1;
+	input->scale_taps.vtaps = pipe->plane_res.scl_data.taps.v_taps;
+	input->scale_taps.vtaps_c = pipe->plane_res.scl_data.taps.v_taps_c;
+	input->scale_taps.htaps_c              = pipe->plane_res.scl_data.taps.h_taps_c;
+	input->scale_ratio_depth.hscl_ratio_c  = pipe->plane_res.scl_data.ratios.horz_c.value/4294967296.0;
+	input->scale_ratio_depth.vscl_ratio_c  = pipe->plane_res.scl_data.ratios.vert_c.value/4294967296.0;
+	input->scale_ratio_depth.vinit_c       = pipe->plane_res.scl_data.inits.v_c.value/4294967296.0;
+	if (input->scale_ratio_depth.vinit_c < 1.0)
+			input->scale_ratio_depth.vinit_c = 1;
+	switch (pipe->plane_res.scl_data.lb_params.depth) {
+	case LB_PIXEL_DEPTH_30BPP:
+		input->scale_ratio_depth.lb_depth = 30; break;
+	case LB_PIXEL_DEPTH_36BPP:
+		input->scale_ratio_depth.lb_depth = 36; break;
+	default:
+		input->scale_ratio_depth.lb_depth = 24; break;
+	}
+
+
+	input->dest.vactive        = pipe->stream->timing.v_addressable + pipe->stream->timing.v_border_top
+			+ pipe->stream->timing.v_border_bottom;
+
+	input->dest.recout_width   = pipe->plane_res.scl_data.recout.width;
+	input->dest.recout_height  = pipe->plane_res.scl_data.recout.height;
+
+	input->dest.full_recout_width   = pipe->plane_res.scl_data.recout.width;
+	input->dest.full_recout_height  = pipe->plane_res.scl_data.recout.height;
+
+	input->dest.htotal         = pipe->stream->timing.h_total;
+	input->dest.hblank_start   = input->dest.htotal - pipe->stream->timing.h_front_porch;
+	input->dest.hblank_end     = input->dest.hblank_start
+			- pipe->stream->timing.h_addressable
+			- pipe->stream->timing.h_border_left
+			- pipe->stream->timing.h_border_right;
+
+	input->dest.vtotal         = pipe->stream->timing.v_total;
+	input->dest.vblank_start   = input->dest.vtotal - pipe->stream->timing.v_front_porch;
+	input->dest.vblank_end     = input->dest.vblank_start
+			- pipe->stream->timing.v_addressable
+			- pipe->stream->timing.v_border_bottom
+			- pipe->stream->timing.v_border_top;
+	input->dest.pixel_rate_mhz = pipe->stream->timing.pix_clk_100hz/10000.0;
+	input->dest.vstartup_start = pipe->pipe_dlg_param.vstartup_start;
+	input->dest.vupdate_offset = pipe->pipe_dlg_param.vupdate_offset;
+	input->dest.vupdate_offset = pipe->pipe_dlg_param.vupdate_offset;
+	input->dest.vupdate_width = pipe->pipe_dlg_param.vupdate_width;
+
+}
+
+static void dcn_bw_calc_rq_dlg_ttu(
+		const struct dc *dc,
+		const struct dcn_bw_internal_vars *v,
+		struct pipe_ctx *pipe,
+		int in_idx)
+{
+	struct display_mode_lib *dml = (struct display_mode_lib *)(&dc->dml);
+	struct _vcs_dpi_display_dlg_regs_st *dlg_regs = &pipe->dlg_regs;
+	struct _vcs_dpi_display_ttu_regs_st *ttu_regs = &pipe->ttu_regs;
+	struct _vcs_dpi_display_rq_regs_st *rq_regs = &pipe->rq_regs;
+	struct _vcs_dpi_display_rq_params_st rq_param = {0};
+	struct _vcs_dpi_display_dlg_sys_params_st dlg_sys_param = {0};
+	struct _vcs_dpi_display_e2e_pipe_params_st input = { { { 0 } } };
+	float total_active_bw = 0;
+	float total_prefetch_bw = 0;
+	int total_flip_bytes = 0;
+	int i;
+
+	memset(dlg_regs, 0, sizeof(*dlg_regs));
+	memset(ttu_regs, 0, sizeof(*ttu_regs));
+	memset(rq_regs, 0, sizeof(*rq_regs));
+
+	for (i = 0; i < number_of_planes; i++) {
+		total_active_bw += v->read_bandwidth[i];
+		total_prefetch_bw += v->prefetch_bandwidth[i];
+		total_flip_bytes += v->total_immediate_flip_bytes[i];
+	}
+	dlg_sys_param.total_flip_bw = v->return_bw - dcn_bw_max2(total_active_bw, total_prefetch_bw);
+	if (dlg_sys_param.total_flip_bw < 0.0)
+		dlg_sys_param.total_flip_bw = 0;
+
+	dlg_sys_param.t_mclk_wm_us = v->dram_clock_change_watermark;
+	dlg_sys_param.t_sr_wm_us = v->stutter_enter_plus_exit_watermark;
+	dlg_sys_param.t_urg_wm_us = v->urgent_watermark;
+	dlg_sys_param.t_extra_us = v->urgent_extra_latency;
+	dlg_sys_param.deepsleep_dcfclk_mhz = v->dcf_clk_deep_sleep;
+	dlg_sys_param.total_flip_bytes = total_flip_bytes;
+
+	pipe_ctx_to_e2e_pipe_params(pipe, &input.pipe);
+	input.clks_cfg.dcfclk_mhz = v->dcfclk;
+	input.clks_cfg.dispclk_mhz = v->dispclk;
+	input.clks_cfg.dppclk_mhz = v->dppclk;
+	input.clks_cfg.refclk_mhz = dc->res_pool->ref_clocks.dchub_ref_clock_inKhz / 1000.0;
+	input.clks_cfg.socclk_mhz = v->socclk;
+	input.clks_cfg.voltage = v->voltage_level;
+//	dc->dml.logger = pool->base.logger;
+	input.dout.output_format = (v->output_format[in_idx] == dcn_bw_420) ? dm_420 : dm_444;
+	input.dout.output_type  = (v->output[in_idx] == dcn_bw_hdmi) ? dm_hdmi : dm_dp;
+	//input[in_idx].dout.output_standard;
+
+	/*todo: soc->sr_enter_plus_exit_time??*/
+	dlg_sys_param.t_srx_delay_us = dc->dcn_ip->dcfclk_cstate_latency / v->dcf_clk_deep_sleep;
+
+	dml1_rq_dlg_get_rq_params(dml, &rq_param, input.pipe.src);
+	dml1_extract_rq_regs(dml, rq_regs, rq_param);
+	dml1_rq_dlg_get_dlg_params(
+			dml,
+			dlg_regs,
+			ttu_regs,
+			rq_param.dlg,
+			dlg_sys_param,
+			input,
+			true,
+			true,
+			v->pte_enable == dcn_bw_yes,
+			pipe->plane_state->flip_immediate);
+}
+
+static void split_stream_across_pipes(
+		struct resource_context *res_ctx,
+		const struct resource_pool *pool,
+		struct pipe_ctx *primary_pipe,
+		struct pipe_ctx *secondary_pipe)
+{
+	int pipe_idx = secondary_pipe->pipe_idx;
+
+	if (!primary_pipe->plane_state)
+		return;
+
+	*secondary_pipe = *primary_pipe;
+
+	secondary_pipe->pipe_idx = pipe_idx;
+	secondary_pipe->plane_res.mi = pool->mis[secondary_pipe->pipe_idx];
+	secondary_pipe->plane_res.hubp = pool->hubps[secondary_pipe->pipe_idx];
+	secondary_pipe->plane_res.ipp = pool->ipps[secondary_pipe->pipe_idx];
+	secondary_pipe->plane_res.xfm = pool->transforms[secondary_pipe->pipe_idx];
+	secondary_pipe->plane_res.dpp = pool->dpps[secondary_pipe->pipe_idx];
+	secondary_pipe->plane_res.mpcc_inst = pool->dpps[secondary_pipe->pipe_idx]->inst;
+	if (primary_pipe->bottom_pipe) {
+		ASSERT(primary_pipe->bottom_pipe != secondary_pipe);
+		secondary_pipe->bottom_pipe = primary_pipe->bottom_pipe;
+		secondary_pipe->bottom_pipe->top_pipe = secondary_pipe;
+	}
+	primary_pipe->bottom_pipe = secondary_pipe;
+	secondary_pipe->top_pipe = primary_pipe;
+
+	resource_build_scaling_params(primary_pipe);
+	resource_build_scaling_params(secondary_pipe);
+}
+
+#if 0
+static void calc_wm_sets_and_perf_params(
+		struct dc_state *context,
+		struct dcn_bw_internal_vars *v)
+{
+	/* Calculate set A last to keep internal var state consistent for required config */
+	if (v->voltage_level < 2) {
+		v->fabric_and_dram_bandwidth_per_state[1] = v->fabric_and_dram_bandwidth_vnom0p8;
+		v->fabric_and_dram_bandwidth_per_state[0] = v->fabric_and_dram_bandwidth_vnom0p8;
+		v->fabric_and_dram_bandwidth = v->fabric_and_dram_bandwidth_vnom0p8;
+		dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(v);
+
+		context->bw_ctx.bw.dcn.watermarks.b.cstate_pstate.cstate_exit_ns =
+			v->stutter_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.b.cstate_pstate.cstate_enter_plus_exit_ns =
+				v->stutter_enter_plus_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.b.cstate_pstate.pstate_change_ns =
+				v->dram_clock_change_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.b.pte_meta_urgent_ns = v->ptemeta_urgent_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.b.urgent_ns = v->urgent_watermark * 1000;
+
+		v->dcfclk_per_state[1] = v->dcfclkv_nom0p8;
+		v->dcfclk_per_state[0] = v->dcfclkv_nom0p8;
+		v->dcfclk = v->dcfclkv_nom0p8;
+		dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(v);
+
+		context->bw_ctx.bw.dcn.watermarks.c.cstate_pstate.cstate_exit_ns =
+			v->stutter_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.c.cstate_pstate.cstate_enter_plus_exit_ns =
+				v->stutter_enter_plus_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.c.cstate_pstate.pstate_change_ns =
+				v->dram_clock_change_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.c.pte_meta_urgent_ns = v->ptemeta_urgent_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.c.urgent_ns = v->urgent_watermark * 1000;
+	}
+
+	if (v->voltage_level < 3) {
+		v->fabric_and_dram_bandwidth_per_state[2] = v->fabric_and_dram_bandwidth_vmax0p9;
+		v->fabric_and_dram_bandwidth_per_state[1] = v->fabric_and_dram_bandwidth_vmax0p9;
+		v->fabric_and_dram_bandwidth_per_state[0] = v->fabric_and_dram_bandwidth_vmax0p9;
+		v->fabric_and_dram_bandwidth = v->fabric_and_dram_bandwidth_vmax0p9;
+		v->dcfclk_per_state[2] = v->dcfclkv_max0p9;
+		v->dcfclk_per_state[1] = v->dcfclkv_max0p9;
+		v->dcfclk_per_state[0] = v->dcfclkv_max0p9;
+		v->dcfclk = v->dcfclkv_max0p9;
+		dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(v);
+
+		context->bw_ctx.bw.dcn.watermarks.d.cstate_pstate.cstate_exit_ns =
+			v->stutter_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.d.cstate_pstate.cstate_enter_plus_exit_ns =
+				v->stutter_enter_plus_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.d.cstate_pstate.pstate_change_ns =
+				v->dram_clock_change_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.d.pte_meta_urgent_ns = v->ptemeta_urgent_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.d.urgent_ns = v->urgent_watermark * 1000;
+	}
+
+	v->fabric_and_dram_bandwidth_per_state[2] = v->fabric_and_dram_bandwidth_vnom0p8;
+	v->fabric_and_dram_bandwidth_per_state[1] = v->fabric_and_dram_bandwidth_vmid0p72;
+	v->fabric_and_dram_bandwidth_per_state[0] = v->fabric_and_dram_bandwidth_vmin0p65;
+	v->fabric_and_dram_bandwidth = v->fabric_and_dram_bandwidth_per_state[v->voltage_level];
+	v->dcfclk_per_state[2] = v->dcfclkv_nom0p8;
+	v->dcfclk_per_state[1] = v->dcfclkv_mid0p72;
+	v->dcfclk_per_state[0] = v->dcfclkv_min0p65;
+	v->dcfclk = v->dcfclk_per_state[v->voltage_level];
+	dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(v);
+
+	context->bw_ctx.bw.dcn.watermarks.a.cstate_pstate.cstate_exit_ns =
+		v->stutter_exit_watermark * 1000;
+	context->bw_ctx.bw.dcn.watermarks.a.cstate_pstate.cstate_enter_plus_exit_ns =
+			v->stutter_enter_plus_exit_watermark * 1000;
+	context->bw_ctx.bw.dcn.watermarks.a.cstate_pstate.pstate_change_ns =
+			v->dram_clock_change_watermark * 1000;
+	context->bw_ctx.bw.dcn.watermarks.a.pte_meta_urgent_ns = v->ptemeta_urgent_watermark * 1000;
+	context->bw_ctx.bw.dcn.watermarks.a.urgent_ns = v->urgent_watermark * 1000;
+	if (v->voltage_level >= 2) {
+		context->bw_ctx.bw.dcn.watermarks.b = context->bw_ctx.bw.dcn.watermarks.a;
+		context->bw_ctx.bw.dcn.watermarks.c = context->bw_ctx.bw.dcn.watermarks.a;
+	}
+	if (v->voltage_level >= 3)
+		context->bw_ctx.bw.dcn.watermarks.d = context->bw_ctx.bw.dcn.watermarks.a;
+}
+#endif
+
+static bool dcn_bw_apply_registry_override(struct dc *dc)
+{
+	bool updated = false;
+
+	DC_FP_START();
+	if ((int)(dc->dcn_soc->sr_exit_time * 1000) != dc->debug.sr_exit_time_ns
+			&& dc->debug.sr_exit_time_ns) {
+		updated = true;
+		dc->dcn_soc->sr_exit_time = dc->debug.sr_exit_time_ns / 1000.0;
+	}
+
+	if ((int)(dc->dcn_soc->sr_enter_plus_exit_time * 1000)
+				!= dc->debug.sr_enter_plus_exit_time_ns
+			&& dc->debug.sr_enter_plus_exit_time_ns) {
+		updated = true;
+		dc->dcn_soc->sr_enter_plus_exit_time =
+				dc->debug.sr_enter_plus_exit_time_ns / 1000.0;
+	}
+
+	if ((int)(dc->dcn_soc->urgent_latency * 1000) != dc->debug.urgent_latency_ns
+			&& dc->debug.urgent_latency_ns) {
+		updated = true;
+		dc->dcn_soc->urgent_latency = dc->debug.urgent_latency_ns / 1000.0;
+	}
+
+	if ((int)(dc->dcn_soc->percent_of_ideal_drambw_received_after_urg_latency * 1000)
+				!= dc->debug.percent_of_ideal_drambw
+			&& dc->debug.percent_of_ideal_drambw) {
+		updated = true;
+		dc->dcn_soc->percent_of_ideal_drambw_received_after_urg_latency =
+				dc->debug.percent_of_ideal_drambw;
+	}
+
+	if ((int)(dc->dcn_soc->dram_clock_change_latency * 1000)
+				!= dc->debug.dram_clock_change_latency_ns
+			&& dc->debug.dram_clock_change_latency_ns) {
+		updated = true;
+		dc->dcn_soc->dram_clock_change_latency =
+				dc->debug.dram_clock_change_latency_ns / 1000.0;
+	}
+	DC_FP_END();
+
+	return updated;
+}
+
+static void hack_disable_optional_pipe_split(struct dcn_bw_internal_vars *v)
+{
+	/*
+	 * disable optional pipe split by lower dispclk bounding box
+	 * at DPM0
+	 */
+	v->max_dispclk[0] = v->max_dppclk_vmin0p65;
+}
+
+static void hack_force_pipe_split(struct dcn_bw_internal_vars *v,
+		unsigned int pixel_rate_100hz)
+{
+	float pixel_rate_mhz = pixel_rate_100hz / 10000;
+
+	/*
+	 * force enabling pipe split by lower dpp clock for DPM0 to just
+	 * below the specify pixel_rate, so bw calc would split pipe.
+	 */
+	if (pixel_rate_mhz < v->max_dppclk[0])
+		v->max_dppclk[0] = pixel_rate_mhz;
+}
+
+static void hack_bounding_box(struct dcn_bw_internal_vars *v,
+		struct dc_debug_options *dbg,
+		struct dc_state *context)
+{
+	int i;
+
+	for (i = 0; i < MAX_PIPES; i++) {
+		struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i];
+
+		/**
+		 * Workaround for avoiding pipe-split in cases where we'd split
+		 * planes that are too small, resulting in splits that aren't
+		 * valid for the scaler.
+		 */
+		if (pipe->plane_state &&
+		    (pipe->plane_state->dst_rect.width <= 16 ||
+		     pipe->plane_state->dst_rect.height <= 16 ||
+		     pipe->plane_state->src_rect.width <= 16 ||
+		     pipe->plane_state->src_rect.height <= 16)) {
+			hack_disable_optional_pipe_split(v);
+			return;
+		}
+	}
+
+	if (dbg->pipe_split_policy == MPC_SPLIT_AVOID)
+		hack_disable_optional_pipe_split(v);
+
+	if (dbg->pipe_split_policy == MPC_SPLIT_AVOID_MULT_DISP &&
+		context->stream_count >= 2)
+		hack_disable_optional_pipe_split(v);
+
+	if (context->stream_count == 1 &&
+			dbg->force_single_disp_pipe_split)
+		hack_force_pipe_split(v, context->streams[0]->timing.pix_clk_100hz);
+}
+
+unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
+{
+	/* for low power RV2 variants, the highest voltage level we want is 0 */
+	if ((chip_family == FAMILY_RV) &&
+	     ASICREV_IS_RAVEN2(hw_internal_rev))
+		switch (pci_revision_id) {
+		case PRID_DALI_DE:
+		case PRID_DALI_DF:
+		case PRID_DALI_E3:
+		case PRID_DALI_E4:
+		case PRID_POLLOCK_94:
+		case PRID_POLLOCK_95:
+		case PRID_POLLOCK_E9:
+		case PRID_POLLOCK_EA:
+		case PRID_POLLOCK_EB:
+			return 0;
+		default:
+			break;
+		}
+
+	/* we are ok with all levels */
+	return 4;
+}
+
+bool dcn_validate_bandwidth(
+		struct dc *dc,
+		struct dc_state *context,
+		bool fast_validate)
+{
+	/*
+	 * we want a breakdown of the various stages of validation, which the
+	 * perf_trace macro doesn't support
+	 */
+	BW_VAL_TRACE_SETUP();
+
+	const struct resource_pool *pool = dc->res_pool;
+	struct dcn_bw_internal_vars *v = &context->dcn_bw_vars;
+	int i, input_idx, k;
+	int vesa_sync_start, asic_blank_end, asic_blank_start;
+	bool bw_limit_pass;
+	float bw_limit;
+
+	PERFORMANCE_TRACE_START();
+
+	BW_VAL_TRACE_COUNT();
+
+	if (dcn_bw_apply_registry_override(dc))
+		dcn_bw_sync_calcs_and_dml(dc);
+
+	memset(v, 0, sizeof(*v));
+	DC_FP_START();
+
+	v->sr_exit_time = dc->dcn_soc->sr_exit_time;
+	v->sr_enter_plus_exit_time = dc->dcn_soc->sr_enter_plus_exit_time;
+	v->urgent_latency = dc->dcn_soc->urgent_latency;
+	v->write_back_latency = dc->dcn_soc->write_back_latency;
+	v->percent_of_ideal_drambw_received_after_urg_latency =
+			dc->dcn_soc->percent_of_ideal_drambw_received_after_urg_latency;
+
+	v->dcfclkv_min0p65 = dc->dcn_soc->dcfclkv_min0p65;
+	v->dcfclkv_mid0p72 = dc->dcn_soc->dcfclkv_mid0p72;
+	v->dcfclkv_nom0p8 = dc->dcn_soc->dcfclkv_nom0p8;
+	v->dcfclkv_max0p9 = dc->dcn_soc->dcfclkv_max0p9;
+
+	v->max_dispclk_vmin0p65 = dc->dcn_soc->max_dispclk_vmin0p65;
+	v->max_dispclk_vmid0p72 = dc->dcn_soc->max_dispclk_vmid0p72;
+	v->max_dispclk_vnom0p8 = dc->dcn_soc->max_dispclk_vnom0p8;
+	v->max_dispclk_vmax0p9 = dc->dcn_soc->max_dispclk_vmax0p9;
+
+	v->max_dppclk_vmin0p65 = dc->dcn_soc->max_dppclk_vmin0p65;
+	v->max_dppclk_vmid0p72 = dc->dcn_soc->max_dppclk_vmid0p72;
+	v->max_dppclk_vnom0p8 = dc->dcn_soc->max_dppclk_vnom0p8;
+	v->max_dppclk_vmax0p9 = dc->dcn_soc->max_dppclk_vmax0p9;
+
+	v->socclk = dc->dcn_soc->socclk;
+
+	v->fabric_and_dram_bandwidth_vmin0p65 = dc->dcn_soc->fabric_and_dram_bandwidth_vmin0p65;
+	v->fabric_and_dram_bandwidth_vmid0p72 = dc->dcn_soc->fabric_and_dram_bandwidth_vmid0p72;
+	v->fabric_and_dram_bandwidth_vnom0p8 = dc->dcn_soc->fabric_and_dram_bandwidth_vnom0p8;
+	v->fabric_and_dram_bandwidth_vmax0p9 = dc->dcn_soc->fabric_and_dram_bandwidth_vmax0p9;
+
+	v->phyclkv_min0p65 = dc->dcn_soc->phyclkv_min0p65;
+	v->phyclkv_mid0p72 = dc->dcn_soc->phyclkv_mid0p72;
+	v->phyclkv_nom0p8 = dc->dcn_soc->phyclkv_nom0p8;
+	v->phyclkv_max0p9 = dc->dcn_soc->phyclkv_max0p9;
+
+	v->downspreading = dc->dcn_soc->downspreading;
+	v->round_trip_ping_latency_cycles = dc->dcn_soc->round_trip_ping_latency_cycles;
+	v->urgent_out_of_order_return_per_channel = dc->dcn_soc->urgent_out_of_order_return_per_channel;
+	v->number_of_channels = dc->dcn_soc->number_of_channels;
+	v->vmm_page_size = dc->dcn_soc->vmm_page_size;
+	v->dram_clock_change_latency = dc->dcn_soc->dram_clock_change_latency;
+	v->return_bus_width = dc->dcn_soc->return_bus_width;
+
+	v->rob_buffer_size_in_kbyte = dc->dcn_ip->rob_buffer_size_in_kbyte;
+	v->det_buffer_size_in_kbyte = dc->dcn_ip->det_buffer_size_in_kbyte;
+	v->dpp_output_buffer_pixels = dc->dcn_ip->dpp_output_buffer_pixels;
+	v->opp_output_buffer_lines = dc->dcn_ip->opp_output_buffer_lines;
+	v->pixel_chunk_size_in_kbyte = dc->dcn_ip->pixel_chunk_size_in_kbyte;
+	v->pte_enable = dc->dcn_ip->pte_enable;
+	v->pte_chunk_size = dc->dcn_ip->pte_chunk_size;
+	v->meta_chunk_size = dc->dcn_ip->meta_chunk_size;
+	v->writeback_chunk_size = dc->dcn_ip->writeback_chunk_size;
+	v->odm_capability = dc->dcn_ip->odm_capability;
+	v->dsc_capability = dc->dcn_ip->dsc_capability;
+	v->line_buffer_size = dc->dcn_ip->line_buffer_size;
+	v->is_line_buffer_bpp_fixed = dc->dcn_ip->is_line_buffer_bpp_fixed;
+	v->line_buffer_fixed_bpp = dc->dcn_ip->line_buffer_fixed_bpp;
+	v->max_line_buffer_lines = dc->dcn_ip->max_line_buffer_lines;
+	v->writeback_luma_buffer_size = dc->dcn_ip->writeback_luma_buffer_size;
+	v->writeback_chroma_buffer_size = dc->dcn_ip->writeback_chroma_buffer_size;
+	v->max_num_dpp = dc->dcn_ip->max_num_dpp;
+	v->max_num_writeback = dc->dcn_ip->max_num_writeback;
+	v->max_dchub_topscl_throughput = dc->dcn_ip->max_dchub_topscl_throughput;
+	v->max_pscl_tolb_throughput = dc->dcn_ip->max_pscl_tolb_throughput;
+	v->max_lb_tovscl_throughput = dc->dcn_ip->max_lb_tovscl_throughput;
+	v->max_vscl_tohscl_throughput = dc->dcn_ip->max_vscl_tohscl_throughput;
+	v->max_hscl_ratio = dc->dcn_ip->max_hscl_ratio;
+	v->max_vscl_ratio = dc->dcn_ip->max_vscl_ratio;
+	v->max_hscl_taps = dc->dcn_ip->max_hscl_taps;
+	v->max_vscl_taps = dc->dcn_ip->max_vscl_taps;
+	v->under_scan_factor = dc->dcn_ip->under_scan_factor;
+	v->pte_buffer_size_in_requests = dc->dcn_ip->pte_buffer_size_in_requests;
+	v->dispclk_ramping_margin = dc->dcn_ip->dispclk_ramping_margin;
+	v->max_inter_dcn_tile_repeaters = dc->dcn_ip->max_inter_dcn_tile_repeaters;
+	v->can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one =
+			dc->dcn_ip->can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one;
+	v->bug_forcing_luma_and_chroma_request_to_same_size_fixed =
+			dc->dcn_ip->bug_forcing_luma_and_chroma_request_to_same_size_fixed;
+
+	v->voltage[5] = dcn_bw_no_support;
+	v->voltage[4] = dcn_bw_v_max0p9;
+	v->voltage[3] = dcn_bw_v_max0p9;
+	v->voltage[2] = dcn_bw_v_nom0p8;
+	v->voltage[1] = dcn_bw_v_mid0p72;
+	v->voltage[0] = dcn_bw_v_min0p65;
+	v->fabric_and_dram_bandwidth_per_state[5] = v->fabric_and_dram_bandwidth_vmax0p9;
+	v->fabric_and_dram_bandwidth_per_state[4] = v->fabric_and_dram_bandwidth_vmax0p9;
+	v->fabric_and_dram_bandwidth_per_state[3] = v->fabric_and_dram_bandwidth_vmax0p9;
+	v->fabric_and_dram_bandwidth_per_state[2] = v->fabric_and_dram_bandwidth_vnom0p8;
+	v->fabric_and_dram_bandwidth_per_state[1] = v->fabric_and_dram_bandwidth_vmid0p72;
+	v->fabric_and_dram_bandwidth_per_state[0] = v->fabric_and_dram_bandwidth_vmin0p65;
+	v->dcfclk_per_state[5] = v->dcfclkv_max0p9;
+	v->dcfclk_per_state[4] = v->dcfclkv_max0p9;
+	v->dcfclk_per_state[3] = v->dcfclkv_max0p9;
+	v->dcfclk_per_state[2] = v->dcfclkv_nom0p8;
+	v->dcfclk_per_state[1] = v->dcfclkv_mid0p72;
+	v->dcfclk_per_state[0] = v->dcfclkv_min0p65;
+	v->max_dispclk[5] = v->max_dispclk_vmax0p9;
+	v->max_dispclk[4] = v->max_dispclk_vmax0p9;
+	v->max_dispclk[3] = v->max_dispclk_vmax0p9;
+	v->max_dispclk[2] = v->max_dispclk_vnom0p8;
+	v->max_dispclk[1] = v->max_dispclk_vmid0p72;
+	v->max_dispclk[0] = v->max_dispclk_vmin0p65;
+	v->max_dppclk[5] = v->max_dppclk_vmax0p9;
+	v->max_dppclk[4] = v->max_dppclk_vmax0p9;
+	v->max_dppclk[3] = v->max_dppclk_vmax0p9;
+	v->max_dppclk[2] = v->max_dppclk_vnom0p8;
+	v->max_dppclk[1] = v->max_dppclk_vmid0p72;
+	v->max_dppclk[0] = v->max_dppclk_vmin0p65;
+	v->phyclk_per_state[5] = v->phyclkv_max0p9;
+	v->phyclk_per_state[4] = v->phyclkv_max0p9;
+	v->phyclk_per_state[3] = v->phyclkv_max0p9;
+	v->phyclk_per_state[2] = v->phyclkv_nom0p8;
+	v->phyclk_per_state[1] = v->phyclkv_mid0p72;
+	v->phyclk_per_state[0] = v->phyclkv_min0p65;
+	v->synchronized_vblank = dcn_bw_no;
+	v->ta_pscalculation = dcn_bw_override;
+	v->allow_different_hratio_vratio = dcn_bw_yes;
+
+	for (i = 0, input_idx = 0; i < pool->pipe_count; i++) {
+		struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i];
+
+		if (!pipe->stream)
+			continue;
+		/* skip all but first of split pipes */
+		if (pipe->top_pipe && pipe->top_pipe->plane_state == pipe->plane_state)
+			continue;
+
+		v->underscan_output[input_idx] = false; /* taken care of in recout already*/
+		v->interlace_output[input_idx] = false;
+
+		v->htotal[input_idx] = pipe->stream->timing.h_total;
+		v->vtotal[input_idx] = pipe->stream->timing.v_total;
+		v->vactive[input_idx] = pipe->stream->timing.v_addressable +
+				pipe->stream->timing.v_border_top + pipe->stream->timing.v_border_bottom;
+		v->v_sync_plus_back_porch[input_idx] = pipe->stream->timing.v_total
+				- v->vactive[input_idx]
+				- pipe->stream->timing.v_front_porch;
+		v->pixel_clock[input_idx] = pipe->stream->timing.pix_clk_100hz/10000.0;
+		if (pipe->stream->timing.timing_3d_format == TIMING_3D_FORMAT_HW_FRAME_PACKING)
+			v->pixel_clock[input_idx] *= 2;
+		if (!pipe->plane_state) {
+			v->dcc_enable[input_idx] = dcn_bw_yes;
+			v->source_pixel_format[input_idx] = dcn_bw_rgb_sub_32;
+			v->source_surface_mode[input_idx] = dcn_bw_sw_4_kb_s;
+			v->lb_bit_per_pixel[input_idx] = 30;
+			v->viewport_width[input_idx] = pipe->stream->timing.h_addressable;
+			v->viewport_height[input_idx] = pipe->stream->timing.v_addressable;
+			/*
+			 * for cases where we have no plane, we want to validate up to 1080p
+			 * source size because here we are only interested in if the output
+			 * timing is supported or not. if we cannot support native resolution
+			 * of the high res display, we still want to support lower res up scale
+			 * to native
+			 */
+			if (v->viewport_width[input_idx] > 1920)
+				v->viewport_width[input_idx] = 1920;
+			if (v->viewport_height[input_idx] > 1080)
+				v->viewport_height[input_idx] = 1080;
+			v->scaler_rec_out_width[input_idx] = v->viewport_width[input_idx];
+			v->scaler_recout_height[input_idx] = v->viewport_height[input_idx];
+			v->override_hta_ps[input_idx] = 1;
+			v->override_vta_ps[input_idx] = 1;
+			v->override_hta_pschroma[input_idx] = 1;
+			v->override_vta_pschroma[input_idx] = 1;
+			v->source_scan[input_idx] = dcn_bw_hor;
+
+		} else {
+			v->viewport_height[input_idx] =  pipe->plane_res.scl_data.viewport.height;
+			v->viewport_width[input_idx] = pipe->plane_res.scl_data.viewport.width;
+			v->scaler_rec_out_width[input_idx] = pipe->plane_res.scl_data.recout.width;
+			v->scaler_recout_height[input_idx] = pipe->plane_res.scl_data.recout.height;
+			if (pipe->bottom_pipe && pipe->bottom_pipe->plane_state == pipe->plane_state) {
+				if (pipe->plane_state->rotation % 2 == 0) {
+					int viewport_end = pipe->plane_res.scl_data.viewport.width
+							+ pipe->plane_res.scl_data.viewport.x;
+					int viewport_b_end = pipe->bottom_pipe->plane_res.scl_data.viewport.width
+							+ pipe->bottom_pipe->plane_res.scl_data.viewport.x;
+
+					if (viewport_end > viewport_b_end)
+						v->viewport_width[input_idx] = viewport_end
+							- pipe->bottom_pipe->plane_res.scl_data.viewport.x;
+					else
+						v->viewport_width[input_idx] = viewport_b_end
+									- pipe->plane_res.scl_data.viewport.x;
+				} else  {
+					int viewport_end = pipe->plane_res.scl_data.viewport.height
+						+ pipe->plane_res.scl_data.viewport.y;
+					int viewport_b_end = pipe->bottom_pipe->plane_res.scl_data.viewport.height
+						+ pipe->bottom_pipe->plane_res.scl_data.viewport.y;
+
+					if (viewport_end > viewport_b_end)
+						v->viewport_height[input_idx] = viewport_end
+							- pipe->bottom_pipe->plane_res.scl_data.viewport.y;
+					else
+						v->viewport_height[input_idx] = viewport_b_end
+									- pipe->plane_res.scl_data.viewport.y;
+				}
+				v->scaler_rec_out_width[input_idx] = pipe->plane_res.scl_data.recout.width
+						+ pipe->bottom_pipe->plane_res.scl_data.recout.width;
+			}
+
+			if (pipe->plane_state->rotation % 2 == 0) {
+				ASSERT(pipe->plane_res.scl_data.ratios.horz.value != dc_fixpt_one.value
+					|| v->scaler_rec_out_width[input_idx] == v->viewport_width[input_idx]);
+				ASSERT(pipe->plane_res.scl_data.ratios.vert.value != dc_fixpt_one.value
+					|| v->scaler_recout_height[input_idx] == v->viewport_height[input_idx]);
+			} else {
+				ASSERT(pipe->plane_res.scl_data.ratios.horz.value != dc_fixpt_one.value
+					|| v->scaler_recout_height[input_idx] == v->viewport_width[input_idx]);
+				ASSERT(pipe->plane_res.scl_data.ratios.vert.value != dc_fixpt_one.value
+					|| v->scaler_rec_out_width[input_idx] == v->viewport_height[input_idx]);
+			}
+
+			if (dc->debug.optimized_watermark) {
+				/*
+				 * this method requires us to always re-calculate watermark when dcc change
+				 * between flip.
+				 */
+				v->dcc_enable[input_idx] = pipe->plane_state->dcc.enable ? dcn_bw_yes : dcn_bw_no;
+			} else {
+				/*
+				 * allow us to disable dcc on the fly without re-calculating WM
+				 *
+				 * extra overhead for DCC is quite small.  for 1080p WM without
+				 * DCC is only 0.417us lower (urgent goes from 6.979us to 6.562us)
+				 */
+				unsigned int bpe;
+
+				v->dcc_enable[input_idx] = dc->res_pool->hubbub->funcs->dcc_support_pixel_format(
+						pipe->plane_state->format, &bpe) ? dcn_bw_yes : dcn_bw_no;
+			}
+
+			v->source_pixel_format[input_idx] = tl_pixel_format_to_bw_defs(
+					pipe->plane_state->format);
+			v->source_surface_mode[input_idx] = tl_sw_mode_to_bw_defs(
+					pipe->plane_state->tiling_info.gfx9.swizzle);
+			v->lb_bit_per_pixel[input_idx] = tl_lb_bpp_to_int(pipe->plane_res.scl_data.lb_params.depth);
+			v->override_hta_ps[input_idx] = pipe->plane_res.scl_data.taps.h_taps;
+			v->override_vta_ps[input_idx] = pipe->plane_res.scl_data.taps.v_taps;
+			v->override_hta_pschroma[input_idx] = pipe->plane_res.scl_data.taps.h_taps_c;
+			v->override_vta_pschroma[input_idx] = pipe->plane_res.scl_data.taps.v_taps_c;
+			/*
+			 * Spreadsheet doesn't handle taps_c is one properly,
+			 * need to force Chroma to always be scaled to pass
+			 * bandwidth validation.
+			 */
+			if (v->override_hta_pschroma[input_idx] == 1)
+				v->override_hta_pschroma[input_idx] = 2;
+			if (v->override_vta_pschroma[input_idx] == 1)
+				v->override_vta_pschroma[input_idx] = 2;
+			v->source_scan[input_idx] = (pipe->plane_state->rotation % 2) ? dcn_bw_vert : dcn_bw_hor;
+		}
+		if (v->is_line_buffer_bpp_fixed == dcn_bw_yes)
+			v->lb_bit_per_pixel[input_idx] = v->line_buffer_fixed_bpp;
+		v->dcc_rate[input_idx] = 1; /*TODO: Worst case? does this change?*/
+		v->output_format[input_idx] = pipe->stream->timing.pixel_encoding ==
+				PIXEL_ENCODING_YCBCR420 ? dcn_bw_420 : dcn_bw_444;
+		v->output[input_idx] = pipe->stream->signal ==
+				SIGNAL_TYPE_HDMI_TYPE_A ? dcn_bw_hdmi : dcn_bw_dp;
+		v->output_deep_color[input_idx] = dcn_bw_encoder_8bpc;
+		if (v->output[input_idx] == dcn_bw_hdmi) {
+			switch (pipe->stream->timing.display_color_depth) {
+			case COLOR_DEPTH_101010:
+				v->output_deep_color[input_idx] = dcn_bw_encoder_10bpc;
+				break;
+			case COLOR_DEPTH_121212:
+				v->output_deep_color[input_idx]  = dcn_bw_encoder_12bpc;
+				break;
+			case COLOR_DEPTH_161616:
+				v->output_deep_color[input_idx]  = dcn_bw_encoder_16bpc;
+				break;
+			default:
+				break;
+			}
+		}
+
+		input_idx++;
+	}
+	v->number_of_active_planes = input_idx;
+
+	scaler_settings_calculation(v);
+
+	hack_bounding_box(v, &dc->debug, context);
+
+	mode_support_and_system_configuration(v);
+
+	/* Unhack dppclk: dont bother with trying to pipe split if we cannot maintain dpm0 */
+	if (v->voltage_level != 0
+			&& context->stream_count == 1
+			&& dc->debug.force_single_disp_pipe_split) {
+		v->max_dppclk[0] = v->max_dppclk_vmin0p65;
+		mode_support_and_system_configuration(v);
+	}
+
+	if (v->voltage_level == 0 &&
+			(dc->debug.sr_exit_time_dpm0_ns
+				|| dc->debug.sr_enter_plus_exit_time_dpm0_ns)) {
+
+		if (dc->debug.sr_enter_plus_exit_time_dpm0_ns)
+			v->sr_enter_plus_exit_time =
+				dc->debug.sr_enter_plus_exit_time_dpm0_ns / 1000.0f;
+		if (dc->debug.sr_exit_time_dpm0_ns)
+			v->sr_exit_time =  dc->debug.sr_exit_time_dpm0_ns / 1000.0f;
+		context->bw_ctx.dml.soc.sr_enter_plus_exit_time_us = v->sr_enter_plus_exit_time;
+		context->bw_ctx.dml.soc.sr_exit_time_us = v->sr_exit_time;
+		mode_support_and_system_configuration(v);
+	}
+
+	display_pipe_configuration(v);
+
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->source_scan[k] == dcn_bw_hor)
+			v->swath_width_y[k] = v->viewport_width[k] / v->dpp_per_plane[k];
+		else
+			v->swath_width_y[k] = v->viewport_height[k] / v->dpp_per_plane[k];
+	}
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		if (v->source_pixel_format[k] == dcn_bw_rgb_sub_64) {
+			v->byte_per_pixel_dety[k] = 8.0;
+			v->byte_per_pixel_detc[k] = 0.0;
+		} else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_32) {
+			v->byte_per_pixel_dety[k] = 4.0;
+			v->byte_per_pixel_detc[k] = 0.0;
+		} else if (v->source_pixel_format[k] == dcn_bw_rgb_sub_16) {
+			v->byte_per_pixel_dety[k] = 2.0;
+			v->byte_per_pixel_detc[k] = 0.0;
+		} else if (v->source_pixel_format[k] == dcn_bw_yuv420_sub_8) {
+			v->byte_per_pixel_dety[k] = 1.0;
+			v->byte_per_pixel_detc[k] = 2.0;
+		} else {
+			v->byte_per_pixel_dety[k] = 4.0f / 3.0f;
+			v->byte_per_pixel_detc[k] = 8.0f / 3.0f;
+		}
+	}
+
+	v->total_data_read_bandwidth = 0.0;
+	for (k = 0; k <= v->number_of_active_planes - 1; k++) {
+		v->read_bandwidth_plane_luma[k] = v->swath_width_y[k] * v->dpp_per_plane[k] *
+				dcn_bw_ceil2(v->byte_per_pixel_dety[k], 1.0) / (v->htotal[k] / v->pixel_clock[k]) * v->v_ratio[k];
+		v->read_bandwidth_plane_chroma[k] = v->swath_width_y[k] / 2.0 * v->dpp_per_plane[k] *
+				dcn_bw_ceil2(v->byte_per_pixel_detc[k], 2.0) / (v->htotal[k] / v->pixel_clock[k]) * v->v_ratio[k] / 2.0;
+		v->total_data_read_bandwidth = v->total_data_read_bandwidth +
+				v->read_bandwidth_plane_luma[k] + v->read_bandwidth_plane_chroma[k];
+	}
+
+	BW_VAL_TRACE_END_VOLTAGE_LEVEL();
+
+	if (v->voltage_level != number_of_states_plus_one && !fast_validate) {
+		float bw_consumed = v->total_bandwidth_consumed_gbyte_per_second;
+
+		if (bw_consumed < v->fabric_and_dram_bandwidth_vmin0p65)
+			bw_consumed = v->fabric_and_dram_bandwidth_vmin0p65;
+		else if (bw_consumed < v->fabric_and_dram_bandwidth_vmid0p72)
+			bw_consumed = v->fabric_and_dram_bandwidth_vmid0p72;
+		else if (bw_consumed < v->fabric_and_dram_bandwidth_vnom0p8)
+			bw_consumed = v->fabric_and_dram_bandwidth_vnom0p8;
+		else
+			bw_consumed = v->fabric_and_dram_bandwidth_vmax0p9;
+
+		if (bw_consumed < v->fabric_and_dram_bandwidth)
+			if (dc->debug.voltage_align_fclk)
+				bw_consumed = v->fabric_and_dram_bandwidth;
+
+		display_pipe_configuration(v);
+		/*calc_wm_sets_and_perf_params(context, v);*/
+		/* Only 1 set is used by dcn since no noticeable
+		 * performance improvement was measured and due to hw bug DEGVIDCN10-254
+		 */
+		dispclkdppclkdcfclk_deep_sleep_prefetch_parameters_watermarks_and_performance_calculation(v);
+
+		context->bw_ctx.bw.dcn.watermarks.a.cstate_pstate.cstate_exit_ns =
+			v->stutter_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.a.cstate_pstate.cstate_enter_plus_exit_ns =
+				v->stutter_enter_plus_exit_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.a.cstate_pstate.pstate_change_ns =
+				v->dram_clock_change_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.a.pte_meta_urgent_ns = v->ptemeta_urgent_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.a.urgent_ns = v->urgent_watermark * 1000;
+		context->bw_ctx.bw.dcn.watermarks.b = context->bw_ctx.bw.dcn.watermarks.a;
+		context->bw_ctx.bw.dcn.watermarks.c = context->bw_ctx.bw.dcn.watermarks.a;
+		context->bw_ctx.bw.dcn.watermarks.d = context->bw_ctx.bw.dcn.watermarks.a;
+
+		context->bw_ctx.bw.dcn.clk.fclk_khz = (int)(bw_consumed * 1000000 /
+				(ddr4_dram_factor_single_Channel * v->number_of_channels));
+		if (bw_consumed == v->fabric_and_dram_bandwidth_vmin0p65)
+			context->bw_ctx.bw.dcn.clk.fclk_khz = (int)(bw_consumed * 1000000 / 32);
+
+		context->bw_ctx.bw.dcn.clk.dcfclk_deep_sleep_khz = (int)(v->dcf_clk_deep_sleep * 1000);
+		context->bw_ctx.bw.dcn.clk.dcfclk_khz = (int)(v->dcfclk * 1000);
+
+		context->bw_ctx.bw.dcn.clk.dispclk_khz = (int)(v->dispclk * 1000);
+		if (dc->debug.max_disp_clk == true)
+			context->bw_ctx.bw.dcn.clk.dispclk_khz = (int)(dc->dcn_soc->max_dispclk_vmax0p9 * 1000);
+
+		if (context->bw_ctx.bw.dcn.clk.dispclk_khz <
+				dc->debug.min_disp_clk_khz) {
+			context->bw_ctx.bw.dcn.clk.dispclk_khz =
+					dc->debug.min_disp_clk_khz;
+		}
+
+		context->bw_ctx.bw.dcn.clk.dppclk_khz = context->bw_ctx.bw.dcn.clk.dispclk_khz /
+				v->dispclk_dppclk_ratio;
+		context->bw_ctx.bw.dcn.clk.phyclk_khz = v->phyclk_per_state[v->voltage_level];
+		switch (v->voltage_level) {
+		case 0:
+			context->bw_ctx.bw.dcn.clk.max_supported_dppclk_khz =
+					(int)(dc->dcn_soc->max_dppclk_vmin0p65 * 1000);
+			break;
+		case 1:
+			context->bw_ctx.bw.dcn.clk.max_supported_dppclk_khz =
+					(int)(dc->dcn_soc->max_dppclk_vmid0p72 * 1000);
+			break;
+		case 2:
+			context->bw_ctx.bw.dcn.clk.max_supported_dppclk_khz =
+					(int)(dc->dcn_soc->max_dppclk_vnom0p8 * 1000);
+			break;
+		default:
+			context->bw_ctx.bw.dcn.clk.max_supported_dppclk_khz =
+					(int)(dc->dcn_soc->max_dppclk_vmax0p9 * 1000);
+			break;
+		}
+
+		BW_VAL_TRACE_END_WATERMARKS();
+
+		for (i = 0, input_idx = 0; i < pool->pipe_count; i++) {
+			struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i];
+
+			/* skip inactive pipe */
+			if (!pipe->stream)
+				continue;
+			/* skip all but first of split pipes */
+			if (pipe->top_pipe && pipe->top_pipe->plane_state == pipe->plane_state)
+				continue;
+
+			pipe->pipe_dlg_param.vupdate_width = v->v_update_width_pix[input_idx];
+			pipe->pipe_dlg_param.vupdate_offset = v->v_update_offset_pix[input_idx];
+			pipe->pipe_dlg_param.vready_offset = v->v_ready_offset_pix[input_idx];
+			pipe->pipe_dlg_param.vstartup_start = v->v_startup[input_idx];
+
+			pipe->pipe_dlg_param.htotal = pipe->stream->timing.h_total;
+			pipe->pipe_dlg_param.vtotal = pipe->stream->timing.v_total;
+			vesa_sync_start = pipe->stream->timing.v_addressable +
+						pipe->stream->timing.v_border_bottom +
+						pipe->stream->timing.v_front_porch;
+
+			asic_blank_end = (pipe->stream->timing.v_total -
+						vesa_sync_start -
+						pipe->stream->timing.v_border_top)
+			* (pipe->stream->timing.flags.INTERLACE ? 1 : 0);
+
+			asic_blank_start = asic_blank_end +
+						(pipe->stream->timing.v_border_top +
+						pipe->stream->timing.v_addressable +
+						pipe->stream->timing.v_border_bottom)
+			* (pipe->stream->timing.flags.INTERLACE ? 1 : 0);
+
+			pipe->pipe_dlg_param.vblank_start = asic_blank_start;
+			pipe->pipe_dlg_param.vblank_end = asic_blank_end;
+
+			if (pipe->plane_state) {
+				struct pipe_ctx *hsplit_pipe = pipe->bottom_pipe;
+
+				pipe->plane_state->update_flags.bits.full_update = 1;
+
+				if (v->dpp_per_plane[input_idx] == 2 ||
+					((pipe->stream->view_format ==
+					  VIEW_3D_FORMAT_SIDE_BY_SIDE ||
+					  pipe->stream->view_format ==
+					  VIEW_3D_FORMAT_TOP_AND_BOTTOM) &&
+					(pipe->stream->timing.timing_3d_format ==
+					 TIMING_3D_FORMAT_TOP_AND_BOTTOM ||
+					 pipe->stream->timing.timing_3d_format ==
+					 TIMING_3D_FORMAT_SIDE_BY_SIDE))) {
+					if (hsplit_pipe && hsplit_pipe->plane_state == pipe->plane_state) {
+						/* update previously split pipe */
+						hsplit_pipe->pipe_dlg_param.vupdate_width = v->v_update_width_pix[input_idx];
+						hsplit_pipe->pipe_dlg_param.vupdate_offset = v->v_update_offset_pix[input_idx];
+						hsplit_pipe->pipe_dlg_param.vready_offset = v->v_ready_offset_pix[input_idx];
+						hsplit_pipe->pipe_dlg_param.vstartup_start = v->v_startup[input_idx];
+
+						hsplit_pipe->pipe_dlg_param.htotal = pipe->stream->timing.h_total;
+						hsplit_pipe->pipe_dlg_param.vtotal = pipe->stream->timing.v_total;
+						hsplit_pipe->pipe_dlg_param.vblank_start = pipe->pipe_dlg_param.vblank_start;
+						hsplit_pipe->pipe_dlg_param.vblank_end = pipe->pipe_dlg_param.vblank_end;
+					} else {
+						/* pipe not split previously needs split */
+						hsplit_pipe = find_idle_secondary_pipe(&context->res_ctx, pool, pipe);
+						ASSERT(hsplit_pipe);
+						split_stream_across_pipes(&context->res_ctx, pool, pipe, hsplit_pipe);
+					}
+
+					dcn_bw_calc_rq_dlg_ttu(dc, v, hsplit_pipe, input_idx);
+				} else if (hsplit_pipe && hsplit_pipe->plane_state == pipe->plane_state) {
+					/* merge previously split pipe */
+					pipe->bottom_pipe = hsplit_pipe->bottom_pipe;
+					if (hsplit_pipe->bottom_pipe)
+						hsplit_pipe->bottom_pipe->top_pipe = pipe;
+					hsplit_pipe->plane_state = NULL;
+					hsplit_pipe->stream = NULL;
+					hsplit_pipe->top_pipe = NULL;
+					hsplit_pipe->bottom_pipe = NULL;
+					/* Clear plane_res and stream_res */
+					memset(&hsplit_pipe->plane_res, 0, sizeof(hsplit_pipe->plane_res));
+					memset(&hsplit_pipe->stream_res, 0, sizeof(hsplit_pipe->stream_res));
+					resource_build_scaling_params(pipe);
+				}
+				/* for now important to do this after pipe split for building e2e params */
+				dcn_bw_calc_rq_dlg_ttu(dc, v, pipe, input_idx);
+			}
+
+			input_idx++;
+		}
+	} else if (v->voltage_level == number_of_states_plus_one) {
+		BW_VAL_TRACE_SKIP(fail);
+	} else if (fast_validate) {
+		BW_VAL_TRACE_SKIP(fast);
+	}
+
+	if (v->voltage_level == 0) {
+		context->bw_ctx.dml.soc.sr_enter_plus_exit_time_us =
+				dc->dcn_soc->sr_enter_plus_exit_time;
+		context->bw_ctx.dml.soc.sr_exit_time_us = dc->dcn_soc->sr_exit_time;
+	}
+
+	/*
+	 * BW limit is set to prevent display from impacting other system functions
+	 */
+
+	bw_limit = dc->dcn_soc->percent_disp_bw_limit * v->fabric_and_dram_bandwidth_vmax0p9;
+	bw_limit_pass = (v->total_data_read_bandwidth / 1000.0) < bw_limit;
+
+	DC_FP_END();
+
+	PERFORMANCE_TRACE_END();
+	BW_VAL_TRACE_FINISH();
+
+	if (bw_limit_pass && v->voltage_level <= get_highest_allowed_voltage_level(
+							dc->ctx->asic_id.chip_family,
+							dc->ctx->asic_id.hw_internal_rev,
+							dc->ctx->asic_id.pci_revision_id))
+		return true;
+	else
+		return false;
+}
+
+static unsigned int dcn_find_normalized_clock_vdd_Level(
+	const struct dc *dc,
+	enum dm_pp_clock_type clocks_type,
+	int clocks_in_khz)
+{
+	int vdd_level = dcn_bw_v_min0p65;
+
+	if (clocks_in_khz == 0)/*todo some clock not in the considerations*/
+		return vdd_level;
+
+	switch (clocks_type) {
+	case DM_PP_CLOCK_TYPE_DISPLAY_CLK:
+		if (clocks_in_khz > dc->dcn_soc->max_dispclk_vmax0p9*1000) {
+			vdd_level = dcn_bw_v_max0p91;
+			BREAK_TO_DEBUGGER();
+		} else if (clocks_in_khz > dc->dcn_soc->max_dispclk_vnom0p8*1000) {
+			vdd_level = dcn_bw_v_max0p9;
+		} else if (clocks_in_khz > dc->dcn_soc->max_dispclk_vmid0p72*1000) {
+			vdd_level = dcn_bw_v_nom0p8;
+		} else if (clocks_in_khz > dc->dcn_soc->max_dispclk_vmin0p65*1000) {
+			vdd_level = dcn_bw_v_mid0p72;
+		} else
+			vdd_level = dcn_bw_v_min0p65;
+		break;
+	case DM_PP_CLOCK_TYPE_DISPLAYPHYCLK:
+		if (clocks_in_khz > dc->dcn_soc->phyclkv_max0p9*1000) {
+			vdd_level = dcn_bw_v_max0p91;
+			BREAK_TO_DEBUGGER();
+		} else if (clocks_in_khz > dc->dcn_soc->phyclkv_nom0p8*1000) {
+			vdd_level = dcn_bw_v_max0p9;
+		} else if (clocks_in_khz > dc->dcn_soc->phyclkv_mid0p72*1000) {
+			vdd_level = dcn_bw_v_nom0p8;
+		} else if (clocks_in_khz > dc->dcn_soc->phyclkv_min0p65*1000) {
+			vdd_level = dcn_bw_v_mid0p72;
+		} else
+			vdd_level = dcn_bw_v_min0p65;
+		break;
+
+	case DM_PP_CLOCK_TYPE_DPPCLK:
+		if (clocks_in_khz > dc->dcn_soc->max_dppclk_vmax0p9*1000) {
+			vdd_level = dcn_bw_v_max0p91;
+			BREAK_TO_DEBUGGER();
+		} else if (clocks_in_khz > dc->dcn_soc->max_dppclk_vnom0p8*1000) {
+			vdd_level = dcn_bw_v_max0p9;
+		} else if (clocks_in_khz > dc->dcn_soc->max_dppclk_vmid0p72*1000) {
+			vdd_level = dcn_bw_v_nom0p8;
+		} else if (clocks_in_khz > dc->dcn_soc->max_dppclk_vmin0p65*1000) {
+			vdd_level = dcn_bw_v_mid0p72;
+		} else
+			vdd_level = dcn_bw_v_min0p65;
+		break;
+
+	case DM_PP_CLOCK_TYPE_MEMORY_CLK:
+		{
+			unsigned factor = (ddr4_dram_factor_single_Channel * dc->dcn_soc->number_of_channels);
+
+			if (clocks_in_khz > dc->dcn_soc->fabric_and_dram_bandwidth_vmax0p9*1000000/factor) {
+				vdd_level = dcn_bw_v_max0p91;
+				BREAK_TO_DEBUGGER();
+			} else if (clocks_in_khz > dc->dcn_soc->fabric_and_dram_bandwidth_vnom0p8*1000000/factor) {
+				vdd_level = dcn_bw_v_max0p9;
+			} else if (clocks_in_khz > dc->dcn_soc->fabric_and_dram_bandwidth_vmid0p72*1000000/factor) {
+				vdd_level = dcn_bw_v_nom0p8;
+			} else if (clocks_in_khz > dc->dcn_soc->fabric_and_dram_bandwidth_vmin0p65*1000000/factor) {
+				vdd_level = dcn_bw_v_mid0p72;
+			} else
+				vdd_level = dcn_bw_v_min0p65;
+		}
+		break;
+
+	case DM_PP_CLOCK_TYPE_DCFCLK:
+		if (clocks_in_khz > dc->dcn_soc->dcfclkv_max0p9*1000) {
+			vdd_level = dcn_bw_v_max0p91;
+			BREAK_TO_DEBUGGER();
+		} else if (clocks_in_khz > dc->dcn_soc->dcfclkv_nom0p8*1000) {
+			vdd_level = dcn_bw_v_max0p9;
+		} else if (clocks_in_khz > dc->dcn_soc->dcfclkv_mid0p72*1000) {
+			vdd_level = dcn_bw_v_nom0p8;
+		} else if (clocks_in_khz > dc->dcn_soc->dcfclkv_min0p65*1000) {
+			vdd_level = dcn_bw_v_mid0p72;
+		} else
+			vdd_level = dcn_bw_v_min0p65;
+		break;
+
+	default:
+		 break;
+	}
+	return vdd_level;
+}
+
+unsigned int dcn_find_dcfclk_suits_all(
+	const struct dc *dc,
+	struct dc_clocks *clocks)
+{
+	unsigned vdd_level, vdd_level_temp;
+	unsigned dcf_clk;
+
+	/*find a common supported voltage level*/
+	vdd_level = dcn_find_normalized_clock_vdd_Level(
+		dc, DM_PP_CLOCK_TYPE_DISPLAY_CLK, clocks->dispclk_khz);
+	vdd_level_temp = dcn_find_normalized_clock_vdd_Level(
+		dc, DM_PP_CLOCK_TYPE_DISPLAYPHYCLK, clocks->phyclk_khz);
+
+	vdd_level = dcn_bw_max(vdd_level, vdd_level_temp);
+	vdd_level_temp = dcn_find_normalized_clock_vdd_Level(
+		dc, DM_PP_CLOCK_TYPE_DPPCLK, clocks->dppclk_khz);
+	vdd_level = dcn_bw_max(vdd_level, vdd_level_temp);
+
+	vdd_level_temp = dcn_find_normalized_clock_vdd_Level(
+		dc, DM_PP_CLOCK_TYPE_MEMORY_CLK, clocks->fclk_khz);
+	vdd_level = dcn_bw_max(vdd_level, vdd_level_temp);
+	vdd_level_temp = dcn_find_normalized_clock_vdd_Level(
+		dc, DM_PP_CLOCK_TYPE_DCFCLK, clocks->dcfclk_khz);
+
+	/*find that level conresponding dcfclk*/
+	vdd_level = dcn_bw_max(vdd_level, vdd_level_temp);
+	if (vdd_level == dcn_bw_v_max0p91) {
+		BREAK_TO_DEBUGGER();
+		dcf_clk = dc->dcn_soc->dcfclkv_max0p9*1000;
+	} else if (vdd_level == dcn_bw_v_max0p9)
+		dcf_clk =  dc->dcn_soc->dcfclkv_max0p9*1000;
+	else if (vdd_level == dcn_bw_v_nom0p8)
+		dcf_clk =  dc->dcn_soc->dcfclkv_nom0p8*1000;
+	else if (vdd_level == dcn_bw_v_mid0p72)
+		dcf_clk =  dc->dcn_soc->dcfclkv_mid0p72*1000;
+	else
+		dcf_clk =  dc->dcn_soc->dcfclkv_min0p65*1000;
+
+	DC_LOG_BANDWIDTH_CALCS("\tdcf_clk for voltage = %d\n", dcf_clk);
+	return dcf_clk;
+}
+
+static bool verify_clock_values(struct dm_pp_clock_levels_with_voltage *clks)
+{
+	int i;
+
+	if (clks->num_levels == 0)
+		return false;
+
+	for (i = 0; i < clks->num_levels; i++)
+		/* Ensure that the result is sane */
+		if (clks->data[i].clocks_in_khz == 0)
+			return false;
+
+	return true;
+}
+
+void dcn_bw_update_from_pplib(struct dc *dc)
+{
+	struct dc_context *ctx = dc->ctx;
+	struct dm_pp_clock_levels_with_voltage fclks = {0}, dcfclks = {0};
+	bool res;
+	unsigned vmin0p65_idx, vmid0p72_idx, vnom0p8_idx, vmax0p9_idx;
+
+	/* TODO: This is not the proper way to obtain fabric_and_dram_bandwidth, should be min(fclk, memclk) */
+	res = dm_pp_get_clock_levels_by_type_with_voltage(
+			ctx, DM_PP_CLOCK_TYPE_FCLK, &fclks);
+
+	DC_FP_START();
+
+	if (res)
+		res = verify_clock_values(&fclks);
+
+	if (res) {
+		ASSERT(fclks.num_levels);
+
+		vmin0p65_idx = 0;
+		vmid0p72_idx = fclks.num_levels -
+			(fclks.num_levels > 2 ? 3 : (fclks.num_levels > 1 ? 2 : 1));
+		vnom0p8_idx = fclks.num_levels - (fclks.num_levels > 1 ? 2 : 1);
+		vmax0p9_idx = fclks.num_levels - 1;
+
+		dc->dcn_soc->fabric_and_dram_bandwidth_vmin0p65 =
+			32 * (fclks.data[vmin0p65_idx].clocks_in_khz / 1000.0) / 1000.0;
+		dc->dcn_soc->fabric_and_dram_bandwidth_vmid0p72 =
+			dc->dcn_soc->number_of_channels *
+			(fclks.data[vmid0p72_idx].clocks_in_khz / 1000.0)
+			* ddr4_dram_factor_single_Channel / 1000.0;
+		dc->dcn_soc->fabric_and_dram_bandwidth_vnom0p8 =
+			dc->dcn_soc->number_of_channels *
+			(fclks.data[vnom0p8_idx].clocks_in_khz / 1000.0)
+			* ddr4_dram_factor_single_Channel / 1000.0;
+		dc->dcn_soc->fabric_and_dram_bandwidth_vmax0p9 =
+			dc->dcn_soc->number_of_channels *
+			(fclks.data[vmax0p9_idx].clocks_in_khz / 1000.0)
+			* ddr4_dram_factor_single_Channel / 1000.0;
+	} else
+		BREAK_TO_DEBUGGER();
+
+	DC_FP_END();
+
+	res = dm_pp_get_clock_levels_by_type_with_voltage(
+			ctx, DM_PP_CLOCK_TYPE_DCFCLK, &dcfclks);
+
+	DC_FP_START();
+
+	if (res)
+		res = verify_clock_values(&dcfclks);
+
+	if (res && dcfclks.num_levels >= 3) {
+		dc->dcn_soc->dcfclkv_min0p65 = dcfclks.data[0].clocks_in_khz / 1000.0;
+		dc->dcn_soc->dcfclkv_mid0p72 = dcfclks.data[dcfclks.num_levels - 3].clocks_in_khz / 1000.0;
+		dc->dcn_soc->dcfclkv_nom0p8 = dcfclks.data[dcfclks.num_levels - 2].clocks_in_khz / 1000.0;
+		dc->dcn_soc->dcfclkv_max0p9 = dcfclks.data[dcfclks.num_levels - 1].clocks_in_khz / 1000.0;
+	} else
+		BREAK_TO_DEBUGGER();
+
+	DC_FP_END();
+}
+
+void dcn_bw_notify_pplib_of_wm_ranges(struct dc *dc)
+{
+	struct pp_smu_funcs_rv *pp = NULL;
+	struct pp_smu_wm_range_sets ranges = {0};
+	int min_fclk_khz, min_dcfclk_khz, socclk_khz;
+	const int overdrive = 5000000; /* 5 GHz to cover Overdrive */
+
+	if (dc->res_pool->pp_smu)
+		pp = &dc->res_pool->pp_smu->rv_funcs;
+	if (!pp || !pp->set_wm_ranges)
+		return;
+
+	DC_FP_START();
+	min_fclk_khz = dc->dcn_soc->fabric_and_dram_bandwidth_vmin0p65 * 1000000 / 32;
+	min_dcfclk_khz = dc->dcn_soc->dcfclkv_min0p65 * 1000;
+	socclk_khz = dc->dcn_soc->socclk * 1000;
+	DC_FP_END();
+
+	/* Now notify PPLib/SMU about which Watermarks sets they should select
+	 * depending on DPM state they are in. And update BW MGR GFX Engine and
+	 * Memory clock member variables for Watermarks calculations for each
+	 * Watermark Set. Only one watermark set for dcn1 due to hw bug DEGVIDCN10-254.
+	 */
+	/* SOCCLK does not affect anytihng but writeback for DCN so for now we dont
+	 * care what the value is, hence min to overdrive level
+	 */
+	ranges.num_reader_wm_sets = WM_SET_COUNT;
+	ranges.num_writer_wm_sets = WM_SET_COUNT;
+	ranges.reader_wm_sets[0].wm_inst = WM_A;
+	ranges.reader_wm_sets[0].min_drain_clk_mhz = min_dcfclk_khz / 1000;
+	ranges.reader_wm_sets[0].max_drain_clk_mhz = overdrive / 1000;
+	ranges.reader_wm_sets[0].min_fill_clk_mhz = min_fclk_khz / 1000;
+	ranges.reader_wm_sets[0].max_fill_clk_mhz = overdrive / 1000;
+	ranges.writer_wm_sets[0].wm_inst = WM_A;
+	ranges.writer_wm_sets[0].min_fill_clk_mhz = socclk_khz / 1000;
+	ranges.writer_wm_sets[0].max_fill_clk_mhz = overdrive / 1000;
+	ranges.writer_wm_sets[0].min_drain_clk_mhz = min_fclk_khz / 1000;
+	ranges.writer_wm_sets[0].max_drain_clk_mhz = overdrive / 1000;
+
+	if (dc->debug.pplib_wm_report_mode == WM_REPORT_OVERRIDE) {
+		ranges.reader_wm_sets[0].wm_inst = WM_A;
+		ranges.reader_wm_sets[0].min_drain_clk_mhz = 300;
+		ranges.reader_wm_sets[0].max_drain_clk_mhz = 5000;
+		ranges.reader_wm_sets[0].min_fill_clk_mhz = 800;
+		ranges.reader_wm_sets[0].max_fill_clk_mhz = 5000;
+		ranges.writer_wm_sets[0].wm_inst = WM_A;
+		ranges.writer_wm_sets[0].min_fill_clk_mhz = 200;
+		ranges.writer_wm_sets[0].max_fill_clk_mhz = 5000;
+		ranges.writer_wm_sets[0].min_drain_clk_mhz = 800;
+		ranges.writer_wm_sets[0].max_drain_clk_mhz = 5000;
+	}
+
+	ranges.reader_wm_sets[1] = ranges.writer_wm_sets[0];
+	ranges.reader_wm_sets[1].wm_inst = WM_B;
+
+	ranges.reader_wm_sets[2] = ranges.writer_wm_sets[0];
+	ranges.reader_wm_sets[2].wm_inst = WM_C;
+
+	ranges.reader_wm_sets[3] = ranges.writer_wm_sets[0];
+	ranges.reader_wm_sets[3].wm_inst = WM_D;
+
+	/* Notify PP Lib/SMU which Watermarks to use for which clock ranges */
+	pp->set_wm_ranges(&pp->pp_smu, &ranges);
+}
+
+void dcn_bw_sync_calcs_and_dml(struct dc *dc)
+{
+	DC_FP_START();
+	DC_LOG_BANDWIDTH_CALCS("sr_exit_time: %f ns\n"
+			"sr_enter_plus_exit_time: %f ns\n"
+			"urgent_latency: %f ns\n"
+			"write_back_latency: %f ns\n"
+			"percent_of_ideal_drambw_received_after_urg_latency: %f %%\n"
+			"max_request_size: %d bytes\n"
+			"dcfclkv_max0p9: %f kHz\n"
+			"dcfclkv_nom0p8: %f kHz\n"
+			"dcfclkv_mid0p72: %f kHz\n"
+			"dcfclkv_min0p65: %f kHz\n"
+			"max_dispclk_vmax0p9: %f kHz\n"
+			"max_dispclk_vnom0p8: %f kHz\n"
+			"max_dispclk_vmid0p72: %f kHz\n"
+			"max_dispclk_vmin0p65: %f kHz\n"
+			"max_dppclk_vmax0p9: %f kHz\n"
+			"max_dppclk_vnom0p8: %f kHz\n"
+			"max_dppclk_vmid0p72: %f kHz\n"
+			"max_dppclk_vmin0p65: %f kHz\n"
+			"socclk: %f kHz\n"
+			"fabric_and_dram_bandwidth_vmax0p9: %f MB/s\n"
+			"fabric_and_dram_bandwidth_vnom0p8: %f MB/s\n"
+			"fabric_and_dram_bandwidth_vmid0p72: %f MB/s\n"
+			"fabric_and_dram_bandwidth_vmin0p65: %f MB/s\n"
+			"phyclkv_max0p9: %f kHz\n"
+			"phyclkv_nom0p8: %f kHz\n"
+			"phyclkv_mid0p72: %f kHz\n"
+			"phyclkv_min0p65: %f kHz\n"
+			"downspreading: %f %%\n"
+			"round_trip_ping_latency_cycles: %d DCFCLK Cycles\n"
+			"urgent_out_of_order_return_per_channel: %d Bytes\n"
+			"number_of_channels: %d\n"
+			"vmm_page_size: %d Bytes\n"
+			"dram_clock_change_latency: %f ns\n"
+			"return_bus_width: %d Bytes\n",
+			dc->dcn_soc->sr_exit_time * 1000,
+			dc->dcn_soc->sr_enter_plus_exit_time * 1000,
+			dc->dcn_soc->urgent_latency * 1000,
+			dc->dcn_soc->write_back_latency * 1000,
+			dc->dcn_soc->percent_of_ideal_drambw_received_after_urg_latency,
+			dc->dcn_soc->max_request_size,
+			dc->dcn_soc->dcfclkv_max0p9 * 1000,
+			dc->dcn_soc->dcfclkv_nom0p8 * 1000,
+			dc->dcn_soc->dcfclkv_mid0p72 * 1000,
+			dc->dcn_soc->dcfclkv_min0p65 * 1000,
+			dc->dcn_soc->max_dispclk_vmax0p9 * 1000,
+			dc->dcn_soc->max_dispclk_vnom0p8 * 1000,
+			dc->dcn_soc->max_dispclk_vmid0p72 * 1000,
+			dc->dcn_soc->max_dispclk_vmin0p65 * 1000,
+			dc->dcn_soc->max_dppclk_vmax0p9 * 1000,
+			dc->dcn_soc->max_dppclk_vnom0p8 * 1000,
+			dc->dcn_soc->max_dppclk_vmid0p72 * 1000,
+			dc->dcn_soc->max_dppclk_vmin0p65 * 1000,
+			dc->dcn_soc->socclk * 1000,
+			dc->dcn_soc->fabric_and_dram_bandwidth_vmax0p9 * 1000,
+			dc->dcn_soc->fabric_and_dram_bandwidth_vnom0p8 * 1000,
+			dc->dcn_soc->fabric_and_dram_bandwidth_vmid0p72 * 1000,
+			dc->dcn_soc->fabric_and_dram_bandwidth_vmin0p65 * 1000,
+			dc->dcn_soc->phyclkv_max0p9 * 1000,
+			dc->dcn_soc->phyclkv_nom0p8 * 1000,
+			dc->dcn_soc->phyclkv_mid0p72 * 1000,
+			dc->dcn_soc->phyclkv_min0p65 * 1000,
+			dc->dcn_soc->downspreading * 100,
+			dc->dcn_soc->round_trip_ping_latency_cycles,
+			dc->dcn_soc->urgent_out_of_order_return_per_channel,
+			dc->dcn_soc->number_of_channels,
+			dc->dcn_soc->vmm_page_size,
+			dc->dcn_soc->dram_clock_change_latency * 1000,
+			dc->dcn_soc->return_bus_width);
+	DC_LOG_BANDWIDTH_CALCS("rob_buffer_size_in_kbyte: %f\n"
+			"det_buffer_size_in_kbyte: %f\n"
+			"dpp_output_buffer_pixels: %f\n"
+			"opp_output_buffer_lines: %f\n"
+			"pixel_chunk_size_in_kbyte: %f\n"
+			"pte_enable: %d\n"
+			"pte_chunk_size: %d kbytes\n"
+			"meta_chunk_size: %d kbytes\n"
+			"writeback_chunk_size: %d kbytes\n"
+			"odm_capability: %d\n"
+			"dsc_capability: %d\n"
+			"line_buffer_size: %d bits\n"
+			"max_line_buffer_lines: %d\n"
+			"is_line_buffer_bpp_fixed: %d\n"
+			"line_buffer_fixed_bpp: %d\n"
+			"writeback_luma_buffer_size: %d kbytes\n"
+			"writeback_chroma_buffer_size: %d kbytes\n"
+			"max_num_dpp: %d\n"
+			"max_num_writeback: %d\n"
+			"max_dchub_topscl_throughput: %d pixels/dppclk\n"
+			"max_pscl_tolb_throughput: %d pixels/dppclk\n"
+			"max_lb_tovscl_throughput: %d pixels/dppclk\n"
+			"max_vscl_tohscl_throughput: %d pixels/dppclk\n"
+			"max_hscl_ratio: %f\n"
+			"max_vscl_ratio: %f\n"
+			"max_hscl_taps: %d\n"
+			"max_vscl_taps: %d\n"
+			"pte_buffer_size_in_requests: %d\n"
+			"dispclk_ramping_margin: %f %%\n"
+			"under_scan_factor: %f %%\n"
+			"max_inter_dcn_tile_repeaters: %d\n"
+			"can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one: %d\n"
+			"bug_forcing_luma_and_chroma_request_to_same_size_fixed: %d\n"
+			"dcfclk_cstate_latency: %d\n",
+			dc->dcn_ip->rob_buffer_size_in_kbyte,
+			dc->dcn_ip->det_buffer_size_in_kbyte,
+			dc->dcn_ip->dpp_output_buffer_pixels,
+			dc->dcn_ip->opp_output_buffer_lines,
+			dc->dcn_ip->pixel_chunk_size_in_kbyte,
+			dc->dcn_ip->pte_enable,
+			dc->dcn_ip->pte_chunk_size,
+			dc->dcn_ip->meta_chunk_size,
+			dc->dcn_ip->writeback_chunk_size,
+			dc->dcn_ip->odm_capability,
+			dc->dcn_ip->dsc_capability,
+			dc->dcn_ip->line_buffer_size,
+			dc->dcn_ip->max_line_buffer_lines,
+			dc->dcn_ip->is_line_buffer_bpp_fixed,
+			dc->dcn_ip->line_buffer_fixed_bpp,
+			dc->dcn_ip->writeback_luma_buffer_size,
+			dc->dcn_ip->writeback_chroma_buffer_size,
+			dc->dcn_ip->max_num_dpp,
+			dc->dcn_ip->max_num_writeback,
+			dc->dcn_ip->max_dchub_topscl_throughput,
+			dc->dcn_ip->max_pscl_tolb_throughput,
+			dc->dcn_ip->max_lb_tovscl_throughput,
+			dc->dcn_ip->max_vscl_tohscl_throughput,
+			dc->dcn_ip->max_hscl_ratio,
+			dc->dcn_ip->max_vscl_ratio,
+			dc->dcn_ip->max_hscl_taps,
+			dc->dcn_ip->max_vscl_taps,
+			dc->dcn_ip->pte_buffer_size_in_requests,
+			dc->dcn_ip->dispclk_ramping_margin,
+			dc->dcn_ip->under_scan_factor * 100,
+			dc->dcn_ip->max_inter_dcn_tile_repeaters,
+			dc->dcn_ip->can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one,
+			dc->dcn_ip->bug_forcing_luma_and_chroma_request_to_same_size_fixed,
+			dc->dcn_ip->dcfclk_cstate_latency);
+
+	dc->dml.soc.sr_exit_time_us = dc->dcn_soc->sr_exit_time;
+	dc->dml.soc.sr_enter_plus_exit_time_us = dc->dcn_soc->sr_enter_plus_exit_time;
+	dc->dml.soc.urgent_latency_us = dc->dcn_soc->urgent_latency;
+	dc->dml.soc.writeback_latency_us = dc->dcn_soc->write_back_latency;
+	dc->dml.soc.ideal_dram_bw_after_urgent_percent =
+			dc->dcn_soc->percent_of_ideal_drambw_received_after_urg_latency;
+	dc->dml.soc.max_request_size_bytes = dc->dcn_soc->max_request_size;
+	dc->dml.soc.downspread_percent = dc->dcn_soc->downspreading;
+	dc->dml.soc.round_trip_ping_latency_dcfclk_cycles =
+			dc->dcn_soc->round_trip_ping_latency_cycles;
+	dc->dml.soc.urgent_out_of_order_return_per_channel_bytes =
+			dc->dcn_soc->urgent_out_of_order_return_per_channel;
+	dc->dml.soc.num_chans = dc->dcn_soc->number_of_channels;
+	dc->dml.soc.vmm_page_size_bytes = dc->dcn_soc->vmm_page_size;
+	dc->dml.soc.dram_clock_change_latency_us = dc->dcn_soc->dram_clock_change_latency;
+	dc->dml.soc.return_bus_width_bytes = dc->dcn_soc->return_bus_width;
+
+	dc->dml.ip.rob_buffer_size_kbytes = dc->dcn_ip->rob_buffer_size_in_kbyte;
+	dc->dml.ip.det_buffer_size_kbytes = dc->dcn_ip->det_buffer_size_in_kbyte;
+	dc->dml.ip.dpp_output_buffer_pixels = dc->dcn_ip->dpp_output_buffer_pixels;
+	dc->dml.ip.opp_output_buffer_lines = dc->dcn_ip->opp_output_buffer_lines;
+	dc->dml.ip.pixel_chunk_size_kbytes = dc->dcn_ip->pixel_chunk_size_in_kbyte;
+	dc->dml.ip.pte_enable = dc->dcn_ip->pte_enable == dcn_bw_yes;
+	dc->dml.ip.pte_chunk_size_kbytes = dc->dcn_ip->pte_chunk_size;
+	dc->dml.ip.meta_chunk_size_kbytes = dc->dcn_ip->meta_chunk_size;
+	dc->dml.ip.writeback_chunk_size_kbytes = dc->dcn_ip->writeback_chunk_size;
+	dc->dml.ip.line_buffer_size_bits = dc->dcn_ip->line_buffer_size;
+	dc->dml.ip.max_line_buffer_lines = dc->dcn_ip->max_line_buffer_lines;
+	dc->dml.ip.IsLineBufferBppFixed = dc->dcn_ip->is_line_buffer_bpp_fixed == dcn_bw_yes;
+	dc->dml.ip.LineBufferFixedBpp = dc->dcn_ip->line_buffer_fixed_bpp;
+	dc->dml.ip.writeback_luma_buffer_size_kbytes = dc->dcn_ip->writeback_luma_buffer_size;
+	dc->dml.ip.writeback_chroma_buffer_size_kbytes = dc->dcn_ip->writeback_chroma_buffer_size;
+	dc->dml.ip.max_num_dpp = dc->dcn_ip->max_num_dpp;
+	dc->dml.ip.max_num_wb = dc->dcn_ip->max_num_writeback;
+	dc->dml.ip.max_dchub_pscl_bw_pix_per_clk = dc->dcn_ip->max_dchub_topscl_throughput;
+	dc->dml.ip.max_pscl_lb_bw_pix_per_clk = dc->dcn_ip->max_pscl_tolb_throughput;
+	dc->dml.ip.max_lb_vscl_bw_pix_per_clk = dc->dcn_ip->max_lb_tovscl_throughput;
+	dc->dml.ip.max_vscl_hscl_bw_pix_per_clk = dc->dcn_ip->max_vscl_tohscl_throughput;
+	dc->dml.ip.max_hscl_ratio = dc->dcn_ip->max_hscl_ratio;
+	dc->dml.ip.max_vscl_ratio = dc->dcn_ip->max_vscl_ratio;
+	dc->dml.ip.max_hscl_taps = dc->dcn_ip->max_hscl_taps;
+	dc->dml.ip.max_vscl_taps = dc->dcn_ip->max_vscl_taps;
+	/*pte_buffer_size_in_requests missing in dml*/
+	dc->dml.ip.dispclk_ramp_margin_percent = dc->dcn_ip->dispclk_ramping_margin;
+	dc->dml.ip.underscan_factor = dc->dcn_ip->under_scan_factor;
+	dc->dml.ip.max_inter_dcn_tile_repeaters = dc->dcn_ip->max_inter_dcn_tile_repeaters;
+	dc->dml.ip.can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one =
+		dc->dcn_ip->can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one == dcn_bw_yes;
+	dc->dml.ip.bug_forcing_LC_req_same_size_fixed =
+		dc->dcn_ip->bug_forcing_luma_and_chroma_request_to_same_size_fixed == dcn_bw_yes;
+	dc->dml.ip.dcfclk_cstate_latency = dc->dcn_ip->dcfclk_cstate_latency;
+	DC_FP_END();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/dcn20_fpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/dcn20_fpu.c
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include "resource.h"
+
+#include "dcn20_fpu.h"
+
+/**
+ * DOC: DCN2x FPU manipulation Overview
+ *
+ * The DCN architecture relies on FPU operations, which require special
+ * compilation flags and the use of kernel_fpu_begin/end functions; ideally, we
+ * want to avoid spreading FPU access across multiple files. With this idea in
+ * mind, this file aims to centralize all DCN20 and DCN2.1 (DCN2x) functions
+ * that require FPU access in a single place. Code in this file follows the
+ * following code pattern:
+ *
+ * 1. Functions that use FPU operations should be isolated in static functions.
+ * 2. The FPU functions should have the noinline attribute to ensure anything
+ *    that deals with FP register is contained within this call.
+ * 3. All function that needs to be accessed outside this file requires a
+ *    public interface that not uses any FPU reference.
+ * 4. Developers **must not** use DC_FP_START/END in this file, but they need
+ *    to ensure that the caller invokes it before access any function available
+ *    in this file. For this reason, public functions in this file must invoke
+ *    dc_assert_fp_enabled();
+ *
+ * Let's expand a little bit more the idea in the code pattern. To fully
+ * isolate FPU operations in a single place, we must avoid situations where
+ * compilers spill FP values to registers due to FP enable in a specific C
+ * file. Note that even if we isolate all FPU functions in a single file and
+ * call its interface from other files, the compiler might enable the use of
+ * FPU before we call DC_FP_START. Nevertheless, it is the programmer's
+ * responsibility to invoke DC_FP_START/END in the correct place. To highlight
+ * situations where developers forgot to use the FP protection before calling
+ * the DC FPU interface functions, we introduce a helper that checks if the
+ * function is invoked under FP protection. If not, it will trigger a kernel
+ * warning.
+ */
+
+void dcn20_populate_dml_writeback_from_context(struct dc *dc,
+					       struct resource_context *res_ctx,
+					       display_e2e_pipe_params_st *pipes)
+{
+	int pipe_cnt, i;
+
+	dc_assert_fp_enabled();
+
+	for (i = 0, pipe_cnt = 0; i < dc->res_pool->pipe_count; i++) {
+		struct dc_writeback_info *wb_info = &res_ctx->pipe_ctx[i].stream->writeback_info[0];
+
+		if (!res_ctx->pipe_ctx[i].stream)
+			continue;
+
+		/* Set writeback information */
+		pipes[pipe_cnt].dout.wb_enable = (wb_info->wb_enabled == true) ? 1 : 0;
+		pipes[pipe_cnt].dout.num_active_wb++;
+		pipes[pipe_cnt].dout.wb.wb_src_height = wb_info->dwb_params.cnv_params.crop_height;
+		pipes[pipe_cnt].dout.wb.wb_src_width = wb_info->dwb_params.cnv_params.crop_width;
+		pipes[pipe_cnt].dout.wb.wb_dst_width = wb_info->dwb_params.dest_width;
+		pipes[pipe_cnt].dout.wb.wb_dst_height = wb_info->dwb_params.dest_height;
+		pipes[pipe_cnt].dout.wb.wb_htaps_luma = 1;
+		pipes[pipe_cnt].dout.wb.wb_vtaps_luma = 1;
+		pipes[pipe_cnt].dout.wb.wb_htaps_chroma = wb_info->dwb_params.scaler_taps.h_taps_c;
+		pipes[pipe_cnt].dout.wb.wb_vtaps_chroma = wb_info->dwb_params.scaler_taps.v_taps_c;
+		pipes[pipe_cnt].dout.wb.wb_hratio = 1.0;
+		pipes[pipe_cnt].dout.wb.wb_vratio = 1.0;
+		if (wb_info->dwb_params.out_format == dwb_scaler_mode_yuv420) {
+			if (wb_info->dwb_params.output_depth == DWB_OUTPUT_PIXEL_DEPTH_8BPC)
+				pipes[pipe_cnt].dout.wb.wb_pixel_format = dm_420_8;
+			else
+				pipes[pipe_cnt].dout.wb.wb_pixel_format = dm_420_10;
+		} else {
+			pipes[pipe_cnt].dout.wb.wb_pixel_format = dm_444_32;
+		}
+
+		pipe_cnt++;
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/dcn20_fpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/dcn20_fpu.h
@@ -0,0 +1,34 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#ifndef __DCN20_FPU_H__
+#define __DCN20_FPU_H__
+
+void dcn20_populate_dml_writeback_from_context(struct dc *dc,
+					       struct resource_context *res_ctx,
+					       display_e2e_pipe_params_st *pipes);
+
+#endif /* __DCN20_FPU_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_mode_vba_20.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_mode_vba_20.c
@@ -3897,14 +3897,14 @@
 					mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine = mode_lib->vba.PixelClock[k] / 2
 							* (1 + mode_lib->vba.DISPCLKDPPCLKDSCCLKDownSpreading / 100.0);
 
-				locals->ODMCombineEnablePerState[i][k] = false;
+				locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_disabled;
 				mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithoutODMCombine;
 				if (mode_lib->vba.ODMCapability) {
 					if (locals->PlaneRequiredDISPCLKWithoutODMCombine > mode_lib->vba.MaxDispclkRoundedDownToDFSGranularity) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					} else if (locals->HActive[k] > DCN20_MAX_420_IMAGE_WIDTH && locals->OutputFormat[k] == dm_420) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					}
 				}
@@ -3957,7 +3957,7 @@
 				locals->RequiredDISPCLK[i][j] = 0.0;
 				locals->DISPCLK_DPPCLK_Support[i][j] = true;
 				for (k = 0; k <= mode_lib->vba.NumberOfActivePlanes - 1; k++) {
-					locals->ODMCombineEnablePerState[i][k] = false;
+					locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_disabled;
 					if (locals->SwathWidthYSingleDPP[k] <= locals->MaximumSwathWidth[k]) {
 						locals->NoOfDPP[i][j][k] = 1;
 						locals->RequiredDPPCLK[i][j][k] = locals->MinDPPCLKUsingSingleDPP[k]
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_mode_vba_20v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_mode_vba_20v2.c
@@ -4008,17 +4008,17 @@
 					mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine = mode_lib->vba.PixelClock[k] / 2
 							* (1 + mode_lib->vba.DISPCLKDPPCLKDSCCLKDownSpreading / 100.0);
 
-				locals->ODMCombineEnablePerState[i][k] = false;
+				locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_disabled;
 				mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithoutODMCombine;
 				if (mode_lib->vba.ODMCapability) {
 					if (locals->PlaneRequiredDISPCLKWithoutODMCombine > MaxMaxDispclkRoundedDown) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					} else if (locals->DSCEnabled[k] && (locals->HActive[k] > DCN20_MAX_DSC_IMAGE_WIDTH)) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					} else if (locals->HActive[k] > DCN20_MAX_420_IMAGE_WIDTH && locals->OutputFormat[k] == dm_420) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					}
 				}
@@ -4071,7 +4071,7 @@
 				locals->RequiredDISPCLK[i][j] = 0.0;
 				locals->DISPCLK_DPPCLK_Support[i][j] = true;
 				for (k = 0; k <= mode_lib->vba.NumberOfActivePlanes - 1; k++) {
-					locals->ODMCombineEnablePerState[i][k] = false;
+					locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_disabled;
 					if (locals->SwathWidthYSingleDPP[k] <= locals->MaximumSwathWidth[k]) {
 						locals->NoOfDPP[i][j][k] = 1;
 						locals->RequiredDPPCLK[i][j][k] = locals->MinDPPCLKUsingSingleDPP[k]
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c
@@ -768,12 +768,12 @@
 
 void dml20_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param)
+		const display_pipe_params_st *pipe_param)
 {
 	display_rq_params_st rq_param = {0};
 
 	memset(rq_regs, 0, sizeof(*rq_regs));
-	dml20_rq_dlg_get_rq_params(mode_lib, &rq_param, pipe_param.src);
+	dml20_rq_dlg_get_rq_params(mode_lib, &rq_param, pipe_param->src);
 	extract_rq_regs(mode_lib, rq_regs, rq_param);
 
 	print__rq_regs_st(mode_lib, *rq_regs);
@@ -1549,7 +1549,7 @@
 void dml20_rq_dlg_get_dlg_reg(struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.h
@@ -43,7 +43,7 @@
 void dml20_rq_dlg_get_rq_reg(
 		struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param);
+		const display_pipe_params_st *pipe_param);
 
 
 // Function: dml_rq_dlg_get_dlg_reg
@@ -61,7 +61,7 @@
 		struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c
@@ -78,7 +78,7 @@
 
 static unsigned int get_bytes_per_element(enum source_format_class source_format, bool is_chroma)
 {
-	unsigned int ret_val = 0;
+	unsigned int ret_val = 1;
 
 	if (source_format == dm_444_16) {
 		if (!is_chroma)
@@ -768,12 +768,12 @@
 
 void dml20v2_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param)
+		const display_pipe_params_st *pipe_param)
 {
 	display_rq_params_st rq_param = {0};
 
 	memset(rq_regs, 0, sizeof(*rq_regs));
-	dml20v2_rq_dlg_get_rq_params(mode_lib, &rq_param, pipe_param.src);
+	dml20v2_rq_dlg_get_rq_params(mode_lib, &rq_param, pipe_param->src);
 	extract_rq_regs(mode_lib, rq_regs, rq_param);
 
 	print__rq_regs_st(mode_lib, *rq_regs);
@@ -1550,7 +1550,7 @@
 void dml20v2_rq_dlg_get_dlg_reg(struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.h
@@ -43,7 +43,7 @@
 void dml20v2_rq_dlg_get_rq_reg(
 		struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param);
+		const display_pipe_params_st *pipe_param);
 
 
 // Function: dml_rq_dlg_get_dlg_reg
@@ -61,7 +61,7 @@
 		struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c
@@ -3979,17 +3979,17 @@
 					mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine = mode_lib->vba.PixelClock[k] / 2
 							* (1 + mode_lib->vba.DISPCLKDPPCLKDSCCLKDownSpreading / 100.0);
 
-				locals->ODMCombineEnablePerState[i][k] = false;
+				locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_disabled;
 				mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithoutODMCombine;
 				if (mode_lib->vba.ODMCapability) {
 					if (locals->PlaneRequiredDISPCLKWithoutODMCombine > MaxMaxDispclkRoundedDown) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					} else if (locals->DSCEnabled[k] && (locals->HActive[k] > DCN21_MAX_DSC_IMAGE_WIDTH)) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					} else if (locals->HActive[k] > DCN21_MAX_420_IMAGE_WIDTH && locals->OutputFormat[k] == dm_420) {
-						locals->ODMCombineEnablePerState[i][k] = true;
+						locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_2to1;
 						mode_lib->vba.PlaneRequiredDISPCLK = mode_lib->vba.PlaneRequiredDISPCLKWithODMCombine;
 					}
 				}
@@ -4042,7 +4042,7 @@
 				locals->RequiredDISPCLK[i][j] = 0.0;
 				locals->DISPCLK_DPPCLK_Support[i][j] = true;
 				for (k = 0; k <= mode_lib->vba.NumberOfActivePlanes - 1; k++) {
-					locals->ODMCombineEnablePerState[i][k] = false;
+					locals->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_disabled;
 					if (locals->SwathWidthYSingleDPP[k] <= locals->MaximumSwathWidth[k]) {
 						locals->NoOfDPP[i][j][k] = 1;
 						locals->RequiredDPPCLK[i][j][k] = locals->MinDPPCLKUsingSingleDPP[k]
@@ -5218,7 +5218,7 @@
 			mode_lib->vba.ODMCombineEnabled[k] =
 					locals->ODMCombineEnablePerState[mode_lib->vba.VoltageLevel][k];
 		} else {
-			mode_lib->vba.ODMCombineEnabled[k] = false;
+			mode_lib->vba.ODMCombineEnabled[k] = dm_odm_combine_mode_disabled;
 		}
 		mode_lib->vba.DSCEnabled[k] =
 				locals->RequiresDSC[mode_lib->vba.VoltageLevel][k];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c
@@ -53,7 +53,7 @@
 
 static unsigned int get_bytes_per_element(enum source_format_class source_format, bool is_chroma)
 {
-	unsigned int ret_val = 0;
+	unsigned int ret_val = 1;
 
 	if (source_format == dm_444_16) {
 		if (!is_chroma)
@@ -694,7 +694,7 @@
 		display_data_rq_sizing_params_st *rq_sizing_param,
 		display_data_rq_dlg_params_st *rq_dlg_param,
 		display_data_rq_misc_params_st *rq_misc_param,
-		const display_pipe_params_st pipe_param,
+		const display_pipe_params_st *pipe_param,
 		bool is_chroma)
 {
 	bool mode_422 = false;
@@ -706,30 +706,30 @@
 
 	// FIXME check if ppe apply for both luma and chroma in 422 case
 	if (is_chroma) {
-		vp_width = pipe_param.src.viewport_width_c / ppe;
-		vp_height = pipe_param.src.viewport_height_c;
-		data_pitch = pipe_param.src.data_pitch_c;
-		meta_pitch = pipe_param.src.meta_pitch_c;
+		vp_width = pipe_param->src.viewport_width_c / ppe;
+		vp_height = pipe_param->src.viewport_height_c;
+		data_pitch = pipe_param->src.data_pitch_c;
+		meta_pitch = pipe_param->src.meta_pitch_c;
 	} else {
-		vp_width = pipe_param.src.viewport_width / ppe;
-		vp_height = pipe_param.src.viewport_height;
-		data_pitch = pipe_param.src.data_pitch;
-		meta_pitch = pipe_param.src.meta_pitch;
+		vp_width = pipe_param->src.viewport_width / ppe;
+		vp_height = pipe_param->src.viewport_height;
+		data_pitch = pipe_param->src.data_pitch;
+		meta_pitch = pipe_param->src.meta_pitch;
 	}
 
-	if (pipe_param.dest.odm_combine) {
+	if (pipe_param->dest.odm_combine) {
 		unsigned int access_dir;
 		unsigned int full_src_vp_width;
 		unsigned int hactive_half;
 		unsigned int src_hactive_half;
-		access_dir = (pipe_param.src.source_scan == dm_vert); // vp access direction: horizontal or vertical accessed
-		hactive_half  = pipe_param.dest.hactive / 2;
+		access_dir = (pipe_param->src.source_scan == dm_vert); // vp access direction: horizontal or vertical accessed
+		hactive_half  = pipe_param->dest.hactive / 2;
 		if (is_chroma) {
-			full_src_vp_width = pipe_param.scale_ratio_depth.hscl_ratio_c * pipe_param.dest.full_recout_width;
-			src_hactive_half  = pipe_param.scale_ratio_depth.hscl_ratio_c * hactive_half;
+			full_src_vp_width = pipe_param->scale_ratio_depth.hscl_ratio_c * pipe_param->dest.full_recout_width;
+			src_hactive_half  = pipe_param->scale_ratio_depth.hscl_ratio_c * hactive_half;
 		} else {
-			full_src_vp_width = pipe_param.scale_ratio_depth.hscl_ratio * pipe_param.dest.full_recout_width;
-			src_hactive_half  = pipe_param.scale_ratio_depth.hscl_ratio * hactive_half;
+			full_src_vp_width = pipe_param->scale_ratio_depth.hscl_ratio * pipe_param->dest.full_recout_width;
+			src_hactive_half  = pipe_param->scale_ratio_depth.hscl_ratio * hactive_half;
 		}
 
 		if (access_dir == 0) {
@@ -754,7 +754,7 @@
 	rq_sizing_param->meta_chunk_bytes = 2048;
 	rq_sizing_param->min_meta_chunk_bytes = 256;
 
-	if (pipe_param.src.hostvm)
+	if (pipe_param->src.hostvm)
 		rq_sizing_param->mpte_group_bytes = 512;
 	else
 		rq_sizing_param->mpte_group_bytes = 2048;
@@ -768,23 +768,23 @@
 			vp_height,
 			data_pitch,
 			meta_pitch,
-			pipe_param.src.source_format,
-			pipe_param.src.sw_mode,
-			pipe_param.src.macro_tile_size,
-			pipe_param.src.source_scan,
-			pipe_param.src.hostvm,
+			pipe_param->src.source_format,
+			pipe_param->src.sw_mode,
+			pipe_param->src.macro_tile_size,
+			pipe_param->src.source_scan,
+			pipe_param->src.hostvm,
 			is_chroma);
 }
 
 static void dml_rq_dlg_get_rq_params(
 		struct display_mode_lib *mode_lib,
 		display_rq_params_st *rq_param,
-		const display_pipe_params_st pipe_param)
+		const display_pipe_params_st *pipe_param)
 {
 	// get param for luma surface
-	rq_param->yuv420 = pipe_param.src.source_format == dm_420_8
-			|| pipe_param.src.source_format == dm_420_10;
-	rq_param->yuv420_10bpc = pipe_param.src.source_format == dm_420_10;
+	rq_param->yuv420 = pipe_param->src.source_format == dm_420_8
+			|| pipe_param->src.source_format == dm_420_10;
+	rq_param->yuv420_10bpc = pipe_param->src.source_format == dm_420_10;
 
 	get_surf_rq_param(
 			mode_lib,
@@ -794,7 +794,7 @@
 			pipe_param,
 			0);
 
-	if (is_dual_plane((enum source_format_class) (pipe_param.src.source_format))) {
+	if (is_dual_plane((enum source_format_class) (pipe_param->src.source_format))) {
 		// get param for chroma surface
 		get_surf_rq_param(
 				mode_lib,
@@ -806,14 +806,14 @@
 	}
 
 	// calculate how to split the det buffer space between luma and chroma
-	handle_det_buf_split(mode_lib, rq_param, pipe_param.src);
+	handle_det_buf_split(mode_lib, rq_param, pipe_param->src);
 	print__rq_params_st(mode_lib, *rq_param);
 }
 
 void dml21_rq_dlg_get_rq_reg(
 		struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param)
+		const display_pipe_params_st *pipe_param)
 {
 	display_rq_params_st rq_param = {0};
 
@@ -1658,7 +1658,7 @@
 		struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
@@ -1696,7 +1696,7 @@
 	// system parameter calculation done
 
 	dml_print("DML_DLG: Calculation for pipe[%d] start\n\n", pipe_idx);
-	dml_rq_dlg_get_rq_params(mode_lib, &rq_param, e2e_pipe_param[pipe_idx].pipe);
+	dml_rq_dlg_get_rq_params(mode_lib, &rq_param, &e2e_pipe_param[pipe_idx].pipe);
 	dml_rq_dlg_get_dlg_params(
 			mode_lib,
 			e2e_pipe_param,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.h
@@ -44,7 +44,7 @@
 void dml21_rq_dlg_get_rq_reg(
 		struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param);
+		const display_pipe_params_st *pipe_param);
 
 // Function: dml_rq_dlg_get_dlg_reg
 //   Calculate and return DLG and TTU register struct given the system setting
@@ -61,7 +61,7 @@
 		struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c
@@ -283,10 +283,10 @@
 		double DISPCLK,
 		double DCFClkDeepSleep,
 		double PixelClock,
-		long HTotal,
-		long VBlank,
-		long DynamicMetadataTransmittedBytes,
-		long DynamicMetadataLinesBeforeActiveRequired,
+		unsigned int HTotal,
+		unsigned int VBlank,
+		unsigned int DynamicMetadataTransmittedBytes,
+		int DynamicMetadataLinesBeforeActiveRequired,
 		int InterlaceEnable,
 		bool ProgressiveToInterlaceUnitInOPP,
 		double *Tsetup,
@@ -1868,7 +1868,10 @@
 	}
 
 	if (SurfaceTiling == dm_sw_linear) {
-		*dpte_row_height = dml_min(128, 1 << (unsigned int) dml_floor(dml_log2(PTEBufferSizeInRequests * *PixelPTEReqWidth / Pitch), 1));
+		if (PTEBufferSizeInRequests == 0)
+			*dpte_row_height = 1;
+		else
+			*dpte_row_height = dml_min(128, 1 << (unsigned int) dml_floor(dml_log2(PTEBufferSizeInRequests * *PixelPTEReqWidth / Pitch), 1));
 		*dpte_row_width_ub = (dml_ceil(((double) SwathWidth - 1) / *PixelPTEReqWidth, 1) + 1) * *PixelPTEReqWidth;
 		*PixelPTEBytesPerRow = *dpte_row_width_ub / *PixelPTEReqWidth * *PTERequestSize;
 	} else if (ScanDirection != dm_vert) {
@@ -3372,8 +3375,8 @@
 
 
 static void CalculateDynamicMetadataParameters(int MaxInterDCNTileRepeaters, double DPPCLK, double DISPCLK,
-		double DCFClkDeepSleep, double PixelClock, long HTotal, long VBlank, long DynamicMetadataTransmittedBytes,
-		long DynamicMetadataLinesBeforeActiveRequired, int InterlaceEnable, bool ProgressiveToInterlaceUnitInOPP,
+		double DCFClkDeepSleep, double PixelClock, unsigned int HTotal, unsigned int VBlank, unsigned int DynamicMetadataTransmittedBytes,
+		int DynamicMetadataLinesBeforeActiveRequired, int InterlaceEnable, bool ProgressiveToInterlaceUnitInOPP,
 		double *Tsetup, double *Tdmbf, double *Tdmec, double *Tdmsks)
 {
 	double TotalRepeaterDelayTime = 0;
@@ -6658,8 +6661,7 @@
 	return ret;
 }
 
-
-static void UseMinimumDCFCLK(
+static noinline_for_stack void UseMinimumDCFCLK(
 		struct display_mode_lib *mode_lib,
 		int MaxInterDCNTileRepeaters,
 		int MaxPrefetchMode,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c
@@ -747,7 +747,7 @@
 	display_data_rq_sizing_params_st *rq_sizing_param,
 	display_data_rq_dlg_params_st *rq_dlg_param,
 	display_data_rq_misc_params_st *rq_misc_param,
-	const display_pipe_params_st pipe_param,
+	const display_pipe_params_st *pipe_param,
 	bool is_chroma,
 	bool is_alpha)
 {
@@ -761,32 +761,32 @@
 
 	// FIXME check if ppe apply for both luma and chroma in 422 case
 	if (is_chroma | is_alpha) {
-		vp_width = pipe_param.src.viewport_width_c / ppe;
-		vp_height = pipe_param.src.viewport_height_c;
-		data_pitch = pipe_param.src.data_pitch_c;
-		meta_pitch = pipe_param.src.meta_pitch_c;
-		surface_height = pipe_param.src.surface_height_y / 2.0;
+		vp_width = pipe_param->src.viewport_width_c / ppe;
+		vp_height = pipe_param->src.viewport_height_c;
+		data_pitch = pipe_param->src.data_pitch_c;
+		meta_pitch = pipe_param->src.meta_pitch_c;
+		surface_height = pipe_param->src.surface_height_y / 2.0;
 	} else {
-		vp_width = pipe_param.src.viewport_width / ppe;
-		vp_height = pipe_param.src.viewport_height;
-		data_pitch = pipe_param.src.data_pitch;
-		meta_pitch = pipe_param.src.meta_pitch;
-		surface_height = pipe_param.src.surface_height_y;
+		vp_width = pipe_param->src.viewport_width / ppe;
+		vp_height = pipe_param->src.viewport_height;
+		data_pitch = pipe_param->src.data_pitch;
+		meta_pitch = pipe_param->src.meta_pitch;
+		surface_height = pipe_param->src.surface_height_y;
 	}
 
-	if (pipe_param.dest.odm_combine) {
+	if (pipe_param->dest.odm_combine) {
 		unsigned int access_dir = 0;
 		unsigned int full_src_vp_width = 0;
 		unsigned int hactive_odm = 0;
 		unsigned int src_hactive_odm = 0;
-		access_dir = (pipe_param.src.source_scan == dm_vert); // vp access direction: horizontal or vertical accessed
-		hactive_odm  = pipe_param.dest.hactive / ((unsigned int)pipe_param.dest.odm_combine*2);
+		access_dir = (pipe_param->src.source_scan == dm_vert); // vp access direction: horizontal or vertical accessed
+		hactive_odm  = pipe_param->dest.hactive / ((unsigned int) pipe_param->dest.odm_combine*2);
 		if (is_chroma) {
-			full_src_vp_width = pipe_param.scale_ratio_depth.hscl_ratio_c * pipe_param.dest.full_recout_width;
-			src_hactive_odm  = pipe_param.scale_ratio_depth.hscl_ratio_c * hactive_odm;
+			full_src_vp_width = pipe_param->scale_ratio_depth.hscl_ratio_c * pipe_param->dest.full_recout_width;
+			src_hactive_odm  = pipe_param->scale_ratio_depth.hscl_ratio_c * hactive_odm;
 		} else {
-			full_src_vp_width = pipe_param.scale_ratio_depth.hscl_ratio * pipe_param.dest.full_recout_width;
-			src_hactive_odm  = pipe_param.scale_ratio_depth.hscl_ratio * hactive_odm;
+			full_src_vp_width = pipe_param->scale_ratio_depth.hscl_ratio * pipe_param->dest.full_recout_width;
+			src_hactive_odm  = pipe_param->scale_ratio_depth.hscl_ratio * hactive_odm;
 		}
 
 		if (access_dir == 0) {
@@ -815,7 +815,7 @@
 	rq_sizing_param->meta_chunk_bytes = 2048;
 	rq_sizing_param->min_meta_chunk_bytes = 256;
 
-	if (pipe_param.src.hostvm)
+	if (pipe_param->src.hostvm)
 		rq_sizing_param->mpte_group_bytes = 512;
 	else
 		rq_sizing_param->mpte_group_bytes = 2048;
@@ -828,28 +828,28 @@
 		vp_height,
 		data_pitch,
 		meta_pitch,
-		pipe_param.src.source_format,
-		pipe_param.src.sw_mode,
-		pipe_param.src.macro_tile_size,
-		pipe_param.src.source_scan,
-		pipe_param.src.hostvm,
+		pipe_param->src.source_format,
+		pipe_param->src.sw_mode,
+		pipe_param->src.macro_tile_size,
+		pipe_param->src.source_scan,
+		pipe_param->src.hostvm,
 		is_chroma,
 		surface_height);
 }
 
 static void dml_rq_dlg_get_rq_params(struct display_mode_lib *mode_lib,
 	display_rq_params_st *rq_param,
-	const display_pipe_params_st pipe_param)
+	const display_pipe_params_st *pipe_param)
 {
 	// get param for luma surface
-	rq_param->yuv420 = pipe_param.src.source_format == dm_420_8
-	|| pipe_param.src.source_format == dm_420_10
-	|| pipe_param.src.source_format == dm_rgbe_alpha
-	|| pipe_param.src.source_format == dm_420_12;
+	rq_param->yuv420 = pipe_param->src.source_format == dm_420_8
+	|| pipe_param->src.source_format == dm_420_10
+	|| pipe_param->src.source_format == dm_rgbe_alpha
+	|| pipe_param->src.source_format == dm_420_12;
 
-	rq_param->yuv420_10bpc = pipe_param.src.source_format == dm_420_10;
+	rq_param->yuv420_10bpc = pipe_param->src.source_format == dm_420_10;
 
-	rq_param->rgbe_alpha = (pipe_param.src.source_format == dm_rgbe_alpha)?1:0;
+	rq_param->rgbe_alpha = (pipe_param->src.source_format == dm_rgbe_alpha)?1:0;
 
 	get_surf_rq_param(mode_lib,
 		&(rq_param->sizing.rq_l),
@@ -859,7 +859,7 @@
 		0,
 		0);
 
-	if (is_dual_plane((enum source_format_class)(pipe_param.src.source_format))) {
+	if (is_dual_plane((enum source_format_class)(pipe_param->src.source_format))) {
 		// get param for chroma surface
 		get_surf_rq_param(mode_lib,
 			&(rq_param->sizing.rq_c),
@@ -871,13 +871,13 @@
 	}
 
 	// calculate how to split the det buffer space between luma and chroma
-	handle_det_buf_split(mode_lib, rq_param, pipe_param.src);
+	handle_det_buf_split(mode_lib, rq_param, pipe_param->src);
 	print__rq_params_st(mode_lib, *rq_param);
 }
 
 void dml30_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib,
 	display_rq_regs_st *rq_regs,
-	const display_pipe_params_st pipe_param)
+	const display_pipe_params_st *pipe_param)
 {
 	display_rq_params_st rq_param = { 0 };
 
@@ -1831,7 +1831,7 @@
 void dml30_rq_dlg_get_dlg_reg(struct display_mode_lib *mode_lib,
 	display_dlg_regs_st *dlg_regs,
 	display_ttu_regs_st *ttu_regs,
-	display_e2e_pipe_params_st *e2e_pipe_param,
+	const display_e2e_pipe_params_st *e2e_pipe_param,
 	const unsigned int num_pipes,
 	const unsigned int pipe_idx,
 	const bool cstate_en,
@@ -1866,7 +1866,7 @@
 	// system parameter calculation done
 
 	dml_print("DML_DLG: Calculation for pipe[%d] start\n\n", pipe_idx);
-	dml_rq_dlg_get_rq_params(mode_lib, &rq_param, e2e_pipe_param[pipe_idx].pipe);
+	dml_rq_dlg_get_rq_params(mode_lib, &rq_param, &e2e_pipe_param[pipe_idx].pipe);
 	dml_rq_dlg_get_dlg_params(mode_lib,
 		e2e_pipe_param,
 		num_pipes,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.h
@@ -41,7 +41,7 @@
 //            See also: <display_rq_regs_st>
 void dml30_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param);
+		const display_pipe_params_st *pipe_param);
 
 // Function: dml_rq_dlg_get_dlg_reg
 //   Calculate and return DLG and TTU register struct given the system setting
@@ -57,7 +57,7 @@
 void dml30_rq_dlg_get_dlg_reg(struct display_mode_lib             *mode_lib,
 		display_dlg_regs_st          *dlg_regs,
 		display_ttu_regs_st          *ttu_regs,
-		display_e2e_pipe_params_st   *e2e_pipe_param,
+		const display_e2e_pipe_params_st   *e2e_pipe_param,
 		const unsigned int            num_pipes,
 		const unsigned int            pipe_idx,
 		const bool                    cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn31/display_mode_vba_31.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn31/display_mode_vba_31.c
@@ -259,33 +259,13 @@
 
 static void CalculateFlipSchedule(
 		struct display_mode_lib *mode_lib,
+		unsigned int k,
 		double HostVMInefficiencyFactor,
 		double UrgentExtraLatency,
 		double UrgentLatency,
-		unsigned int GPUVMMaxPageTableLevels,
-		bool HostVMEnable,
-		unsigned int HostVMMaxNonCachedPageTableLevels,
-		bool GPUVMEnable,
-		double HostVMMinPageSize,
 		double PDEAndMetaPTEBytesPerFrame,
 		double MetaRowBytes,
-		double DPTEBytesPerRow,
-		double BandwidthAvailableForImmediateFlip,
-		unsigned int TotImmediateFlipBytes,
-		enum source_format_class SourcePixelFormat,
-		double LineTime,
-		double VRatio,
-		double VRatioChroma,
-		double Tno_bw,
-		bool DCCEnable,
-		unsigned int dpte_row_height,
-		unsigned int meta_row_height,
-		unsigned int dpte_row_height_chroma,
-		unsigned int meta_row_height_chroma,
-		double *DestinationLinesToRequestVMInImmediateFlip,
-		double *DestinationLinesToRequestRowInImmediateFlip,
-		double *final_flip_bw,
-		bool *ImmediateFlipSupportedForPipe);
+		double DPTEBytesPerRow);
 static double CalculateWriteBackDelay(
 		enum source_format_class WritebackPixelFormat,
 		double WritebackHRatio,
@@ -319,64 +299,28 @@
 static void CalculateWatermarksAndDRAMSpeedChangeSupport(
 		struct display_mode_lib *mode_lib,
 		unsigned int PrefetchMode,
-		unsigned int NumberOfActivePlanes,
-		unsigned int MaxLineBufferLines,
-		unsigned int LineBufferSize,
-		unsigned int WritebackInterfaceBufferSize,
 		double DCFCLK,
 		double ReturnBW,
-		bool SynchronizedVBlank,
-		unsigned int dpte_group_bytes[],
-		unsigned int MetaChunkSize,
 		double UrgentLatency,
 		double ExtraLatency,
-		double WritebackLatency,
-		double WritebackChunkSize,
 		double SOCCLK,
-		double DRAMClockChangeLatency,
-		double SRExitTime,
-		double SREnterPlusExitTime,
-		double SRExitZ8Time,
-		double SREnterPlusExitZ8Time,
 		double DCFCLKDeepSleep,
 		unsigned int DETBufferSizeY[],
 		unsigned int DETBufferSizeC[],
 		unsigned int SwathHeightY[],
 		unsigned int SwathHeightC[],
-		unsigned int LBBitPerPixel[],
 		double SwathWidthY[],
 		double SwathWidthC[],
-		double HRatio[],
-		double HRatioChroma[],
-		unsigned int vtaps[],
-		unsigned int VTAPsChroma[],
-		double VRatio[],
-		double VRatioChroma[],
-		unsigned int HTotal[],
-		double PixelClock[],
-		unsigned int BlendingAndTiming[],
 		unsigned int DPPPerPlane[],
 		double BytePerPixelDETY[],
 		double BytePerPixelDETC[],
-		double DSTXAfterScaler[],
-		double DSTYAfterScaler[],
-		bool WritebackEnable[],
-		enum source_format_class WritebackPixelFormat[],
-		double WritebackDestinationWidth[],
-		double WritebackDestinationHeight[],
-		double WritebackSourceHeight[],
 		bool UnboundedRequestEnabled,
 		int unsigned CompressedBufferSizeInkByte,
 		enum clock_change_support *DRAMClockChangeSupport,
-		double *UrgentWatermark,
-		double *WritebackUrgentWatermark,
-		double *DRAMClockChangeWatermark,
-		double *WritebackDRAMClockChangeWatermark,
 		double *StutterExitWatermark,
 		double *StutterEnterPlusExitWatermark,
 		double *Z8StutterExitWatermark,
-		double *Z8StutterEnterPlusExitWatermark,
-		double *MinActiveDRAMClockChangeLatencySupported);
+		double *Z8StutterEnterPlusExitWatermark);
 
 static void CalculateDCFCLKDeepSleep(
 		struct display_mode_lib *mode_lib,
@@ -2959,33 +2903,13 @@
 			for (k = 0; k < v->NumberOfActivePlanes; ++k) {
 				CalculateFlipSchedule(
 						mode_lib,
+						k,
 						HostVMInefficiencyFactor,
 						v->UrgentExtraLatency,
 						v->UrgentLatency,
-						v->GPUVMMaxPageTableLevels,
-						v->HostVMEnable,
-						v->HostVMMaxNonCachedPageTableLevels,
-						v->GPUVMEnable,
-						v->HostVMMinPageSize,
 						v->PDEAndMetaPTEBytesFrame[k],
 						v->MetaRowByte[k],
-						v->PixelPTEBytesPerRow[k],
-						v->BandwidthAvailableForImmediateFlip,
-						v->TotImmediateFlipBytes,
-						v->SourcePixelFormat[k],
-						v->HTotal[k] / v->PixelClock[k],
-						v->VRatio[k],
-						v->VRatioChroma[k],
-						v->Tno_bw[k],
-						v->DCCEnable[k],
-						v->dpte_row_height[k],
-						v->meta_row_height[k],
-						v->dpte_row_height_chroma[k],
-						v->meta_row_height_chroma[k],
-						&v->DestinationLinesToRequestVMInImmediateFlip[k],
-						&v->DestinationLinesToRequestRowInImmediateFlip[k],
-						&v->final_flip_bw[k],
-						&v->ImmediateFlipSupportedForPipe[k]);
+						v->PixelPTEBytesPerRow[k]);
 			}
 
 			v->total_dcn_read_bw_with_flip = 0.0;
@@ -3072,64 +2996,28 @@
 		CalculateWatermarksAndDRAMSpeedChangeSupport(
 				mode_lib,
 				PrefetchMode,
-				v->NumberOfActivePlanes,
-				v->MaxLineBufferLines,
-				v->LineBufferSize,
-				v->WritebackInterfaceBufferSize,
 				v->DCFCLK,
 				v->ReturnBW,
-				v->SynchronizedVBlank,
-				v->dpte_group_bytes,
-				v->MetaChunkSize,
 				v->UrgentLatency,
 				v->UrgentExtraLatency,
-				v->WritebackLatency,
-				v->WritebackChunkSize,
 				v->SOCCLK,
-				v->DRAMClockChangeLatency,
-				v->SRExitTime,
-				v->SREnterPlusExitTime,
-				v->SRExitZ8Time,
-				v->SREnterPlusExitZ8Time,
 				v->DCFCLKDeepSleep,
 				v->DETBufferSizeY,
 				v->DETBufferSizeC,
 				v->SwathHeightY,
 				v->SwathHeightC,
-				v->LBBitPerPixel,
 				v->SwathWidthY,
 				v->SwathWidthC,
-				v->HRatio,
-				v->HRatioChroma,
-				v->vtaps,
-				v->VTAPsChroma,
-				v->VRatio,
-				v->VRatioChroma,
-				v->HTotal,
-				v->PixelClock,
-				v->BlendingAndTiming,
 				v->DPPPerPlane,
 				v->BytePerPixelDETY,
 				v->BytePerPixelDETC,
-				v->DSTXAfterScaler,
-				v->DSTYAfterScaler,
-				v->WritebackEnable,
-				v->WritebackPixelFormat,
-				v->WritebackDestinationWidth,
-				v->WritebackDestinationHeight,
-				v->WritebackSourceHeight,
 				v->UnboundedRequestEnabled,
 				v->CompressedBufferSizeInkByte,
 				&DRAMClockChangeSupport,
-				&v->UrgentWatermark,
-				&v->WritebackUrgentWatermark,
-				&v->DRAMClockChangeWatermark,
-				&v->WritebackDRAMClockChangeWatermark,
 				&v->StutterExitWatermark,
 				&v->StutterEnterPlusExitWatermark,
 				&v->Z8StutterExitWatermark,
-				&v->Z8StutterEnterPlusExitWatermark,
-				&v->MinActiveDRAMClockChangeLatencySupported);
+				&v->Z8StutterEnterPlusExitWatermark);
 
 		for (k = 0; k < v->NumberOfActivePlanes; ++k) {
 			if (v->WritebackEnable[k] == true) {
@@ -3741,61 +3629,43 @@
 
 static void CalculateFlipSchedule(
 		struct display_mode_lib *mode_lib,
+		unsigned int k,
 		double HostVMInefficiencyFactor,
 		double UrgentExtraLatency,
 		double UrgentLatency,
-		unsigned int GPUVMMaxPageTableLevels,
-		bool HostVMEnable,
-		unsigned int HostVMMaxNonCachedPageTableLevels,
-		bool GPUVMEnable,
-		double HostVMMinPageSize,
 		double PDEAndMetaPTEBytesPerFrame,
 		double MetaRowBytes,
-		double DPTEBytesPerRow,
-		double BandwidthAvailableForImmediateFlip,
-		unsigned int TotImmediateFlipBytes,
-		enum source_format_class SourcePixelFormat,
-		double LineTime,
-		double VRatio,
-		double VRatioChroma,
-		double Tno_bw,
-		bool DCCEnable,
-		unsigned int dpte_row_height,
-		unsigned int meta_row_height,
-		unsigned int dpte_row_height_chroma,
-		unsigned int meta_row_height_chroma,
-		double *DestinationLinesToRequestVMInImmediateFlip,
-		double *DestinationLinesToRequestRowInImmediateFlip,
-		double *final_flip_bw,
-		bool *ImmediateFlipSupportedForPipe)
+		double DPTEBytesPerRow)
 {
+	struct vba_vars_st *v = &mode_lib->vba;
 	double min_row_time = 0.0;
 	unsigned int HostVMDynamicLevelsTrips;
 	double TimeForFetchingMetaPTEImmediateFlip;
 	double TimeForFetchingRowInVBlankImmediateFlip;
 	double ImmediateFlipBW;
+	double LineTime = v->HTotal[k] / v->PixelClock[k];
 
-	if (GPUVMEnable == true && HostVMEnable == true) {
-		HostVMDynamicLevelsTrips = HostVMMaxNonCachedPageTableLevels;
+	if (v->GPUVMEnable == true && v->HostVMEnable == true) {
+		HostVMDynamicLevelsTrips = v->HostVMMaxNonCachedPageTableLevels;
 	} else {
 		HostVMDynamicLevelsTrips = 0;
 	}
 
-	if (GPUVMEnable == true || DCCEnable == true) {
-		ImmediateFlipBW = (PDEAndMetaPTEBytesPerFrame + MetaRowBytes + DPTEBytesPerRow) * BandwidthAvailableForImmediateFlip / TotImmediateFlipBytes;
+	if (v->GPUVMEnable == true || v->DCCEnable[k] == true) {
+		ImmediateFlipBW = (PDEAndMetaPTEBytesPerFrame + MetaRowBytes + DPTEBytesPerRow) * v->BandwidthAvailableForImmediateFlip / v->TotImmediateFlipBytes;
 	}
 
-	if (GPUVMEnable == true) {
+	if (v->GPUVMEnable == true) {
 		TimeForFetchingMetaPTEImmediateFlip = dml_max3(
-				Tno_bw + PDEAndMetaPTEBytesPerFrame * HostVMInefficiencyFactor / ImmediateFlipBW,
-				UrgentExtraLatency + UrgentLatency * (GPUVMMaxPageTableLevels * (HostVMDynamicLevelsTrips + 1) - 1),
+				v->Tno_bw[k] + PDEAndMetaPTEBytesPerFrame * HostVMInefficiencyFactor / ImmediateFlipBW,
+				UrgentExtraLatency + UrgentLatency * (v->GPUVMMaxPageTableLevels * (HostVMDynamicLevelsTrips + 1) - 1),
 				LineTime / 4.0);
 	} else {
 		TimeForFetchingMetaPTEImmediateFlip = 0;
 	}
 
-	*DestinationLinesToRequestVMInImmediateFlip = dml_ceil(4.0 * (TimeForFetchingMetaPTEImmediateFlip / LineTime), 1) / 4.0;
-	if ((GPUVMEnable == true || DCCEnable == true)) {
+	v->DestinationLinesToRequestVMInImmediateFlip[k] = dml_ceil(4.0 * (TimeForFetchingMetaPTEImmediateFlip / LineTime), 1) / 4.0;
+	if ((v->GPUVMEnable == true || v->DCCEnable[k] == true)) {
 		TimeForFetchingRowInVBlankImmediateFlip = dml_max3(
 				(MetaRowBytes + DPTEBytesPerRow * HostVMInefficiencyFactor) / ImmediateFlipBW,
 				UrgentLatency * (HostVMDynamicLevelsTrips + 1),
@@ -3804,54 +3674,54 @@
 		TimeForFetchingRowInVBlankImmediateFlip = 0;
 	}
 
-	*DestinationLinesToRequestRowInImmediateFlip = dml_ceil(4.0 * (TimeForFetchingRowInVBlankImmediateFlip / LineTime), 1) / 4.0;
+	v->DestinationLinesToRequestRowInImmediateFlip[k] = dml_ceil(4.0 * (TimeForFetchingRowInVBlankImmediateFlip / LineTime), 1) / 4.0;
 
-	if (GPUVMEnable == true) {
-		*final_flip_bw = dml_max(
-				PDEAndMetaPTEBytesPerFrame * HostVMInefficiencyFactor / (*DestinationLinesToRequestVMInImmediateFlip * LineTime),
-				(MetaRowBytes + DPTEBytesPerRow * HostVMInefficiencyFactor) / (*DestinationLinesToRequestRowInImmediateFlip * LineTime));
-	} else if ((GPUVMEnable == true || DCCEnable == true)) {
-		*final_flip_bw = (MetaRowBytes + DPTEBytesPerRow * HostVMInefficiencyFactor) / (*DestinationLinesToRequestRowInImmediateFlip * LineTime);
-	} else {
-		*final_flip_bw = 0;
-	}
-
-	if (SourcePixelFormat == dm_420_8 || SourcePixelFormat == dm_420_10 || SourcePixelFormat == dm_rgbe_alpha) {
-		if (GPUVMEnable == true && DCCEnable != true) {
-			min_row_time = dml_min(dpte_row_height * LineTime / VRatio, dpte_row_height_chroma * LineTime / VRatioChroma);
-		} else if (GPUVMEnable != true && DCCEnable == true) {
-			min_row_time = dml_min(meta_row_height * LineTime / VRatio, meta_row_height_chroma * LineTime / VRatioChroma);
+	if (v->GPUVMEnable == true) {
+		v->final_flip_bw[k] = dml_max(
+				PDEAndMetaPTEBytesPerFrame * HostVMInefficiencyFactor / (v->DestinationLinesToRequestVMInImmediateFlip[k] * LineTime),
+				(MetaRowBytes + DPTEBytesPerRow * HostVMInefficiencyFactor) / (v->DestinationLinesToRequestRowInImmediateFlip[k] * LineTime));
+	} else if ((v->GPUVMEnable == true || v->DCCEnable[k] == true)) {
+		v->final_flip_bw[k] = (MetaRowBytes + DPTEBytesPerRow * HostVMInefficiencyFactor) / (v->DestinationLinesToRequestRowInImmediateFlip[k] * LineTime);
+	} else {
+		v->final_flip_bw[k] = 0;
+	}
+
+	if (v->SourcePixelFormat[k] == dm_420_8 || v->SourcePixelFormat[k] == dm_420_10 || v->SourcePixelFormat[k] == dm_rgbe_alpha) {
+		if (v->GPUVMEnable == true && v->DCCEnable[k] != true) {
+			min_row_time = dml_min(v->dpte_row_height[k] * LineTime / v->VRatio[k], v->dpte_row_height_chroma[k] * LineTime / v->VRatioChroma[k]);
+		} else if (v->GPUVMEnable != true && v->DCCEnable[k] == true) {
+			min_row_time = dml_min(v->meta_row_height[k] * LineTime / v->VRatio[k], v->meta_row_height_chroma[k] * LineTime / v->VRatioChroma[k]);
 		} else {
 			min_row_time = dml_min4(
-					dpte_row_height * LineTime / VRatio,
-					meta_row_height * LineTime / VRatio,
-					dpte_row_height_chroma * LineTime / VRatioChroma,
-					meta_row_height_chroma * LineTime / VRatioChroma);
+					v->dpte_row_height[k] * LineTime / v->VRatio[k],
+					v->meta_row_height[k] * LineTime / v->VRatio[k],
+					v->dpte_row_height_chroma[k] * LineTime / v->VRatioChroma[k],
+					v->meta_row_height_chroma[k] * LineTime / v->VRatioChroma[k]);
 		}
 	} else {
-		if (GPUVMEnable == true && DCCEnable != true) {
-			min_row_time = dpte_row_height * LineTime / VRatio;
-		} else if (GPUVMEnable != true && DCCEnable == true) {
-			min_row_time = meta_row_height * LineTime / VRatio;
+		if (v->GPUVMEnable == true && v->DCCEnable[k] != true) {
+			min_row_time = v->dpte_row_height[k] * LineTime / v->VRatio[k];
+		} else if (v->GPUVMEnable != true && v->DCCEnable[k] == true) {
+			min_row_time = v->meta_row_height[k] * LineTime / v->VRatio[k];
 		} else {
-			min_row_time = dml_min(dpte_row_height * LineTime / VRatio, meta_row_height * LineTime / VRatio);
+			min_row_time = dml_min(v->dpte_row_height[k] * LineTime / v->VRatio[k], v->meta_row_height[k] * LineTime / v->VRatio[k]);
 		}
 	}
 
-	if (*DestinationLinesToRequestVMInImmediateFlip >= 32 || *DestinationLinesToRequestRowInImmediateFlip >= 16
+	if (v->DestinationLinesToRequestVMInImmediateFlip[k] >= 32 || v->DestinationLinesToRequestRowInImmediateFlip[k] >= 16
 			|| TimeForFetchingMetaPTEImmediateFlip + 2 * TimeForFetchingRowInVBlankImmediateFlip > min_row_time) {
-		*ImmediateFlipSupportedForPipe = false;
+		v->ImmediateFlipSupportedForPipe[k] = false;
 	} else {
-		*ImmediateFlipSupportedForPipe = true;
+		v->ImmediateFlipSupportedForPipe[k] = true;
 	}
 
 #ifdef __DML_VBA_DEBUG__
-	dml_print("DML::%s: DestinationLinesToRequestVMInImmediateFlip = %f\n", __func__, *DestinationLinesToRequestVMInImmediateFlip);
-	dml_print("DML::%s: DestinationLinesToRequestRowInImmediateFlip = %f\n", __func__, *DestinationLinesToRequestRowInImmediateFlip);
+	dml_print("DML::%s: DestinationLinesToRequestVMInImmediateFlip = %f\n", __func__, v->DestinationLinesToRequestVMInImmediateFlip[k]);
+	dml_print("DML::%s: DestinationLinesToRequestRowInImmediateFlip = %f\n", __func__, v->DestinationLinesToRequestRowInImmediateFlip[k]);
 	dml_print("DML::%s: TimeForFetchingMetaPTEImmediateFlip = %f\n", __func__, TimeForFetchingMetaPTEImmediateFlip);
 	dml_print("DML::%s: TimeForFetchingRowInVBlankImmediateFlip = %f\n", __func__, TimeForFetchingRowInVBlankImmediateFlip);
 	dml_print("DML::%s: min_row_time = %f\n", __func__, min_row_time);
-	dml_print("DML::%s: ImmediateFlipSupportedForPipe = %d\n", __func__, *ImmediateFlipSupportedForPipe);
+	dml_print("DML::%s: ImmediateFlipSupportedForPipe = %d\n", __func__, v->ImmediateFlipSupportedForPipe[k]);
 #endif
 
 }
@@ -4292,7 +4162,9 @@
 				}
 				if (v->OutputFormat[k] == dm_420 && v->HActive[k] > DCN31_MAX_FMT_420_BUFFER_WIDTH
 						&& v->ODMCombineEnablePerState[i][k] != dm_odm_combine_mode_4to1) {
-					if (v->HActive[k] / 2 > DCN31_MAX_FMT_420_BUFFER_WIDTH) {
+					if (v->Output[k] == dm_hdmi) {
+						FMTBufferExceeded = true;
+					} else if (v->HActive[k] / 2 > DCN31_MAX_FMT_420_BUFFER_WIDTH) {
 						v->ODMCombineEnablePerState[i][k] = dm_odm_combine_mode_4to1;
 						v->PlaneRequiredDISPCLK = v->PlaneRequiredDISPCLKWithODMCombine4To1;
 
@@ -5477,33 +5349,13 @@
 					for (k = 0; k < v->NumberOfActivePlanes; k++) {
 						CalculateFlipSchedule(
 								mode_lib,
+								k,
 								HostVMInefficiencyFactor,
 								v->ExtraLatency,
 								v->UrgLatency[i],
-								v->GPUVMMaxPageTableLevels,
-								v->HostVMEnable,
-								v->HostVMMaxNonCachedPageTableLevels,
-								v->GPUVMEnable,
-								v->HostVMMinPageSize,
 								v->PDEAndMetaPTEBytesPerFrame[i][j][k],
 								v->MetaRowBytes[i][j][k],
-								v->DPTEBytesPerRow[i][j][k],
-								v->BandwidthAvailableForImmediateFlip,
-								v->TotImmediateFlipBytes,
-								v->SourcePixelFormat[k],
-								v->HTotal[k] / v->PixelClock[k],
-								v->VRatio[k],
-								v->VRatioChroma[k],
-								v->Tno_bw[k],
-								v->DCCEnable[k],
-								v->dpte_row_height[k],
-								v->meta_row_height[k],
-								v->dpte_row_height_chroma[k],
-								v->meta_row_height_chroma[k],
-								&v->DestinationLinesToRequestVMInImmediateFlip[k],
-								&v->DestinationLinesToRequestRowInImmediateFlip[k],
-								&v->final_flip_bw[k],
-								&v->ImmediateFlipSupportedForPipe[k]);
+								v->DPTEBytesPerRow[i][j][k]);
 					}
 					v->total_dcn_read_bw_with_flip = 0.0;
 					for (k = 0; k < v->NumberOfActivePlanes; k++) {
@@ -5561,64 +5413,28 @@
 			CalculateWatermarksAndDRAMSpeedChangeSupport(
 					mode_lib,
 					v->PrefetchModePerState[i][j],
-					v->NumberOfActivePlanes,
-					v->MaxLineBufferLines,
-					v->LineBufferSize,
-					v->WritebackInterfaceBufferSize,
 					v->DCFCLKState[i][j],
 					v->ReturnBWPerState[i][j],
-					v->SynchronizedVBlank,
-					v->dpte_group_bytes,
-					v->MetaChunkSize,
 					v->UrgLatency[i],
 					v->ExtraLatency,
-					v->WritebackLatency,
-					v->WritebackChunkSize,
 					v->SOCCLKPerState[i],
-					v->DRAMClockChangeLatency,
-					v->SRExitTime,
-					v->SREnterPlusExitTime,
-					v->SRExitZ8Time,
-					v->SREnterPlusExitZ8Time,
 					v->ProjectedDCFCLKDeepSleep[i][j],
 					v->DETBufferSizeYThisState,
 					v->DETBufferSizeCThisState,
 					v->SwathHeightYThisState,
 					v->SwathHeightCThisState,
-					v->LBBitPerPixel,
 					v->SwathWidthYThisState,
 					v->SwathWidthCThisState,
-					v->HRatio,
-					v->HRatioChroma,
-					v->vtaps,
-					v->VTAPsChroma,
-					v->VRatio,
-					v->VRatioChroma,
-					v->HTotal,
-					v->PixelClock,
-					v->BlendingAndTiming,
 					v->NoOfDPPThisState,
 					v->BytePerPixelInDETY,
 					v->BytePerPixelInDETC,
-					v->DSTXAfterScaler,
-					v->DSTYAfterScaler,
-					v->WritebackEnable,
-					v->WritebackPixelFormat,
-					v->WritebackDestinationWidth,
-					v->WritebackDestinationHeight,
-					v->WritebackSourceHeight,
 					UnboundedRequestEnabledThisState,
 					CompressedBufferSizeInkByteThisState,
 					&v->DRAMClockChangeSupport[i][j],
-					&v->UrgentWatermark,
-					&v->WritebackUrgentWatermark,
-					&v->DRAMClockChangeWatermark,
-					&v->WritebackDRAMClockChangeWatermark,
-					&dummy,
 					&dummy,
 					&dummy,
 					&dummy,
-					&v->MinActiveDRAMClockChangeLatencySupported);
+					&dummy);
 		}
 	}
 
@@ -5743,64 +5559,28 @@
 static void CalculateWatermarksAndDRAMSpeedChangeSupport(
 		struct display_mode_lib *mode_lib,
 		unsigned int PrefetchMode,
-		unsigned int NumberOfActivePlanes,
-		unsigned int MaxLineBufferLines,
-		unsigned int LineBufferSize,
-		unsigned int WritebackInterfaceBufferSize,
 		double DCFCLK,
 		double ReturnBW,
-		bool SynchronizedVBlank,
-		unsigned int dpte_group_bytes[],
-		unsigned int MetaChunkSize,
 		double UrgentLatency,
 		double ExtraLatency,
-		double WritebackLatency,
-		double WritebackChunkSize,
 		double SOCCLK,
-		double DRAMClockChangeLatency,
-		double SRExitTime,
-		double SREnterPlusExitTime,
-		double SRExitZ8Time,
-		double SREnterPlusExitZ8Time,
 		double DCFCLKDeepSleep,
 		unsigned int DETBufferSizeY[],
 		unsigned int DETBufferSizeC[],
 		unsigned int SwathHeightY[],
 		unsigned int SwathHeightC[],
-		unsigned int LBBitPerPixel[],
 		double SwathWidthY[],
 		double SwathWidthC[],
-		double HRatio[],
-		double HRatioChroma[],
-		unsigned int vtaps[],
-		unsigned int VTAPsChroma[],
-		double VRatio[],
-		double VRatioChroma[],
-		unsigned int HTotal[],
-		double PixelClock[],
-		unsigned int BlendingAndTiming[],
 		unsigned int DPPPerPlane[],
 		double BytePerPixelDETY[],
 		double BytePerPixelDETC[],
-		double DSTXAfterScaler[],
-		double DSTYAfterScaler[],
-		bool WritebackEnable[],
-		enum source_format_class WritebackPixelFormat[],
-		double WritebackDestinationWidth[],
-		double WritebackDestinationHeight[],
-		double WritebackSourceHeight[],
 		bool UnboundedRequestEnabled,
 		int unsigned CompressedBufferSizeInkByte,
 		enum clock_change_support *DRAMClockChangeSupport,
-		double *UrgentWatermark,
-		double *WritebackUrgentWatermark,
-		double *DRAMClockChangeWatermark,
-		double *WritebackDRAMClockChangeWatermark,
 		double *StutterExitWatermark,
 		double *StutterEnterPlusExitWatermark,
 		double *Z8StutterExitWatermark,
-		double *Z8StutterEnterPlusExitWatermark,
-		double *MinActiveDRAMClockChangeLatencySupported)
+		double *Z8StutterEnterPlusExitWatermark)
 {
 	struct vba_vars_st *v = &mode_lib->vba;
 	double EffectiveLBLatencyHidingY;
@@ -5820,103 +5600,103 @@
 	double TotalPixelBW = 0.0;
 	int k, j;
 
-	*UrgentWatermark = UrgentLatency + ExtraLatency;
+	v->UrgentWatermark = UrgentLatency + ExtraLatency;
 
 #ifdef __DML_VBA_DEBUG__
 	dml_print("DML::%s: UrgentLatency = %f\n", __func__, UrgentLatency);
 	dml_print("DML::%s: ExtraLatency = %f\n", __func__, ExtraLatency);
-	dml_print("DML::%s: UrgentWatermark = %f\n", __func__, *UrgentWatermark);
+	dml_print("DML::%s: UrgentWatermark = %f\n", __func__, v->UrgentWatermark);
 #endif
 
-	*DRAMClockChangeWatermark = DRAMClockChangeLatency + *UrgentWatermark;
+	v->DRAMClockChangeWatermark = v->DRAMClockChangeLatency + v->UrgentWatermark;
 
 #ifdef __DML_VBA_DEBUG__
-	dml_print("DML::%s: DRAMClockChangeLatency = %f\n", __func__, DRAMClockChangeLatency);
-	dml_print("DML::%s: DRAMClockChangeWatermark = %f\n", __func__, *DRAMClockChangeWatermark);
+	dml_print("DML::%s: v->DRAMClockChangeLatency = %f\n", __func__, v->DRAMClockChangeLatency);
+	dml_print("DML::%s: DRAMClockChangeWatermark = %f\n", __func__, v->DRAMClockChangeWatermark);
 #endif
 
 	v->TotalActiveWriteback = 0;
-	for (k = 0; k < NumberOfActivePlanes; ++k) {
-		if (WritebackEnable[k] == true) {
+	for (k = 0; k < v->NumberOfActivePlanes; ++k) {
+		if (v->WritebackEnable[k] == true) {
 			v->TotalActiveWriteback = v->TotalActiveWriteback + 1;
 		}
 	}
 
 	if (v->TotalActiveWriteback <= 1) {
-		*WritebackUrgentWatermark = WritebackLatency;
+		v->WritebackUrgentWatermark = v->WritebackLatency;
 	} else {
-		*WritebackUrgentWatermark = WritebackLatency + WritebackChunkSize * 1024.0 / 32.0 / SOCCLK;
+		v->WritebackUrgentWatermark = v->WritebackLatency + v->WritebackChunkSize * 1024.0 / 32.0 / SOCCLK;
 	}
 
 	if (v->TotalActiveWriteback <= 1) {
-		*WritebackDRAMClockChangeWatermark = DRAMClockChangeLatency + WritebackLatency;
+		v->WritebackDRAMClockChangeWatermark = v->DRAMClockChangeLatency + v->WritebackLatency;
 	} else {
-		*WritebackDRAMClockChangeWatermark = DRAMClockChangeLatency + WritebackLatency + WritebackChunkSize * 1024.0 / 32.0 / SOCCLK;
+		v->WritebackDRAMClockChangeWatermark = v->DRAMClockChangeLatency + v->WritebackLatency + v->WritebackChunkSize * 1024.0 / 32.0 / SOCCLK;
 	}
 
-	for (k = 0; k < NumberOfActivePlanes; ++k) {
+	for (k = 0; k < v->NumberOfActivePlanes; ++k) {
 		TotalPixelBW = TotalPixelBW
-				+ DPPPerPlane[k] * (SwathWidthY[k] * BytePerPixelDETY[k] * VRatio[k] + SwathWidthC[k] * BytePerPixelDETC[k] * VRatioChroma[k])
-						/ (HTotal[k] / PixelClock[k]);
+				+ DPPPerPlane[k] * (SwathWidthY[k] * BytePerPixelDETY[k] * v->VRatio[k] + SwathWidthC[k] * BytePerPixelDETC[k] * v->VRatioChroma[k])
+						/ (v->HTotal[k] / v->PixelClock[k]);
 	}
 
-	for (k = 0; k < NumberOfActivePlanes; ++k) {
+	for (k = 0; k < v->NumberOfActivePlanes; ++k) {
 		double EffectiveDETBufferSizeY = DETBufferSizeY[k];
 
 		v->LBLatencyHidingSourceLinesY = dml_min(
-				(double) MaxLineBufferLines,
-				dml_floor(LineBufferSize / LBBitPerPixel[k] / (SwathWidthY[k] / dml_max(HRatio[k], 1.0)), 1)) - (vtaps[k] - 1);
+				(double) v->MaxLineBufferLines,
+				dml_floor(v->LineBufferSize / v->LBBitPerPixel[k] / (SwathWidthY[k] / dml_max(v->HRatio[k], 1.0)), 1)) - (v->vtaps[k] - 1);
 
 		v->LBLatencyHidingSourceLinesC = dml_min(
-				(double) MaxLineBufferLines,
-				dml_floor(LineBufferSize / LBBitPerPixel[k] / (SwathWidthC[k] / dml_max(HRatioChroma[k], 1.0)), 1)) - (VTAPsChroma[k] - 1);
+				(double) v->MaxLineBufferLines,
+				dml_floor(v->LineBufferSize / v->LBBitPerPixel[k] / (SwathWidthC[k] / dml_max(v->HRatioChroma[k], 1.0)), 1)) - (v->VTAPsChroma[k] - 1);
 
-		EffectiveLBLatencyHidingY = v->LBLatencyHidingSourceLinesY / VRatio[k] * (HTotal[k] / PixelClock[k]);
+		EffectiveLBLatencyHidingY = v->LBLatencyHidingSourceLinesY / v->VRatio[k] * (v->HTotal[k] / v->PixelClock[k]);
 
-		EffectiveLBLatencyHidingC = v->LBLatencyHidingSourceLinesC / VRatioChroma[k] * (HTotal[k] / PixelClock[k]);
+		EffectiveLBLatencyHidingC = v->LBLatencyHidingSourceLinesC / v->VRatioChroma[k] * (v->HTotal[k] / v->PixelClock[k]);
 
 		if (UnboundedRequestEnabled) {
 			EffectiveDETBufferSizeY = EffectiveDETBufferSizeY
-					+ CompressedBufferSizeInkByte * 1024 * SwathWidthY[k] * BytePerPixelDETY[k] * VRatio[k] / (HTotal[k] / PixelClock[k]) / TotalPixelBW;
+					+ CompressedBufferSizeInkByte * 1024 * SwathWidthY[k] * BytePerPixelDETY[k] * v->VRatio[k] / (v->HTotal[k] / v->PixelClock[k]) / TotalPixelBW;
 		}
 
 		LinesInDETY[k] = (double) EffectiveDETBufferSizeY / BytePerPixelDETY[k] / SwathWidthY[k];
 		LinesInDETYRoundedDownToSwath[k] = dml_floor(LinesInDETY[k], SwathHeightY[k]);
-		FullDETBufferingTimeY = LinesInDETYRoundedDownToSwath[k] * (HTotal[k] / PixelClock[k]) / VRatio[k];
+		FullDETBufferingTimeY = LinesInDETYRoundedDownToSwath[k] * (v->HTotal[k] / v->PixelClock[k]) / v->VRatio[k];
 		if (BytePerPixelDETC[k] > 0) {
 			LinesInDETC = v->DETBufferSizeC[k] / BytePerPixelDETC[k] / SwathWidthC[k];
 			LinesInDETCRoundedDownToSwath = dml_floor(LinesInDETC, SwathHeightC[k]);
-			FullDETBufferingTimeC = LinesInDETCRoundedDownToSwath * (HTotal[k] / PixelClock[k]) / VRatioChroma[k];
+			FullDETBufferingTimeC = LinesInDETCRoundedDownToSwath * (v->HTotal[k] / v->PixelClock[k]) / v->VRatioChroma[k];
 		} else {
 			LinesInDETC = 0;
 			FullDETBufferingTimeC = 999999;
 		}
 
 		ActiveDRAMClockChangeLatencyMarginY = EffectiveLBLatencyHidingY + FullDETBufferingTimeY
-				- ((double) DSTXAfterScaler[k] / HTotal[k] + DSTYAfterScaler[k]) * HTotal[k] / PixelClock[k] - *UrgentWatermark - *DRAMClockChangeWatermark;
+				- ((double) v->DSTXAfterScaler[k] / v->HTotal[k] + v->DSTYAfterScaler[k]) * v->HTotal[k] / v->PixelClock[k] - v->UrgentWatermark - v->DRAMClockChangeWatermark;
 
-		if (NumberOfActivePlanes > 1) {
+		if (v->NumberOfActivePlanes > 1) {
 			ActiveDRAMClockChangeLatencyMarginY = ActiveDRAMClockChangeLatencyMarginY
-					- (1 - 1.0 / NumberOfActivePlanes) * SwathHeightY[k] * HTotal[k] / PixelClock[k] / VRatio[k];
+					- (1 - 1.0 / v->NumberOfActivePlanes) * SwathHeightY[k] * v->HTotal[k] / v->PixelClock[k] / v->VRatio[k];
 		}
 
 		if (BytePerPixelDETC[k] > 0) {
 			ActiveDRAMClockChangeLatencyMarginC = EffectiveLBLatencyHidingC + FullDETBufferingTimeC
-					- ((double) DSTXAfterScaler[k] / HTotal[k] + DSTYAfterScaler[k]) * HTotal[k] / PixelClock[k] - *UrgentWatermark - *DRAMClockChangeWatermark;
+					- ((double) v->DSTXAfterScaler[k] / v->HTotal[k] + v->DSTYAfterScaler[k]) * v->HTotal[k] / v->PixelClock[k] - v->UrgentWatermark - v->DRAMClockChangeWatermark;
 
-			if (NumberOfActivePlanes > 1) {
+			if (v->NumberOfActivePlanes > 1) {
 				ActiveDRAMClockChangeLatencyMarginC = ActiveDRAMClockChangeLatencyMarginC
-						- (1 - 1.0 / NumberOfActivePlanes) * SwathHeightC[k] * HTotal[k] / PixelClock[k] / VRatioChroma[k];
+						- (1 - 1.0 / v->NumberOfActivePlanes) * SwathHeightC[k] * v->HTotal[k] / v->PixelClock[k] / v->VRatioChroma[k];
 			}
 			v->ActiveDRAMClockChangeLatencyMargin[k] = dml_min(ActiveDRAMClockChangeLatencyMarginY, ActiveDRAMClockChangeLatencyMarginC);
 		} else {
 			v->ActiveDRAMClockChangeLatencyMargin[k] = ActiveDRAMClockChangeLatencyMarginY;
 		}
 
-		if (WritebackEnable[k] == true) {
-			WritebackDRAMClockChangeLatencyHiding = WritebackInterfaceBufferSize * 1024
-					/ (WritebackDestinationWidth[k] * WritebackDestinationHeight[k] / (WritebackSourceHeight[k] * HTotal[k] / PixelClock[k]) * 4);
-			if (WritebackPixelFormat[k] == dm_444_64) {
+		if (v->WritebackEnable[k] == true) {
+			WritebackDRAMClockChangeLatencyHiding = v->WritebackInterfaceBufferSize * 1024
+					/ (v->WritebackDestinationWidth[k] * v->WritebackDestinationHeight[k] / (v->WritebackSourceHeight[k] * v->HTotal[k] / v->PixelClock[k]) * 4);
+			if (v->WritebackPixelFormat[k] == dm_444_64) {
 				WritebackDRAMClockChangeLatencyHiding = WritebackDRAMClockChangeLatencyHiding / 2;
 			}
 			WritebackDRAMClockChangeLatencyMargin = WritebackDRAMClockChangeLatencyHiding - v->WritebackDRAMClockChangeWatermark;
@@ -5926,14 +5706,14 @@
 
 	v->MinActiveDRAMClockChangeMargin = 999999;
 	PlaneWithMinActiveDRAMClockChangeMargin = 0;
-	for (k = 0; k < NumberOfActivePlanes; ++k) {
+	for (k = 0; k < v->NumberOfActivePlanes; ++k) {
 		if (v->ActiveDRAMClockChangeLatencyMargin[k] < v->MinActiveDRAMClockChangeMargin) {
 			v->MinActiveDRAMClockChangeMargin = v->ActiveDRAMClockChangeLatencyMargin[k];
-			if (BlendingAndTiming[k] == k) {
+			if (v->BlendingAndTiming[k] == k) {
 				PlaneWithMinActiveDRAMClockChangeMargin = k;
 			} else {
-				for (j = 0; j < NumberOfActivePlanes; ++j) {
-					if (BlendingAndTiming[k] == j) {
+				for (j = 0; j < v->NumberOfActivePlanes; ++j) {
+					if (v->BlendingAndTiming[k] == j) {
 						PlaneWithMinActiveDRAMClockChangeMargin = j;
 					}
 				}
@@ -5941,11 +5721,11 @@
 		}
 	}
 
-	*MinActiveDRAMClockChangeLatencySupported = v->MinActiveDRAMClockChangeMargin + DRAMClockChangeLatency;
+	v->MinActiveDRAMClockChangeLatencySupported = v->MinActiveDRAMClockChangeMargin + v->DRAMClockChangeLatency ;
 
 	SecondMinActiveDRAMClockChangeMarginOneDisplayInVBLank = 999999;
-	for (k = 0; k < NumberOfActivePlanes; ++k) {
-		if (!((k == PlaneWithMinActiveDRAMClockChangeMargin) && (BlendingAndTiming[k] == k)) && !(BlendingAndTiming[k] == PlaneWithMinActiveDRAMClockChangeMargin)
+	for (k = 0; k < v->NumberOfActivePlanes; ++k) {
+		if (!((k == PlaneWithMinActiveDRAMClockChangeMargin) && (v->BlendingAndTiming[k] == k)) && !(v->BlendingAndTiming[k] == PlaneWithMinActiveDRAMClockChangeMargin)
 				&& v->ActiveDRAMClockChangeLatencyMargin[k] < SecondMinActiveDRAMClockChangeMarginOneDisplayInVBLank) {
 			SecondMinActiveDRAMClockChangeMarginOneDisplayInVBLank = v->ActiveDRAMClockChangeLatencyMargin[k];
 		}
@@ -5953,25 +5733,25 @@
 
 	v->TotalNumberOfActiveOTG = 0;
 
-	for (k = 0; k < NumberOfActivePlanes; ++k) {
-		if (BlendingAndTiming[k] == k) {
+	for (k = 0; k < v->NumberOfActivePlanes; ++k) {
+		if (v->BlendingAndTiming[k] == k) {
 			v->TotalNumberOfActiveOTG = v->TotalNumberOfActiveOTG + 1;
 		}
 	}
 
 	if (v->MinActiveDRAMClockChangeMargin > 0 && PrefetchMode == 0) {
 		*DRAMClockChangeSupport = dm_dram_clock_change_vactive;
-	} else if ((SynchronizedVBlank == true || v->TotalNumberOfActiveOTG == 1
+	} else if ((v->SynchronizedVBlank == true || v->TotalNumberOfActiveOTG == 1
 			|| SecondMinActiveDRAMClockChangeMarginOneDisplayInVBLank > 0) && PrefetchMode == 0) {
 		*DRAMClockChangeSupport = dm_dram_clock_change_vblank;
 	} else {
 		*DRAMClockChangeSupport = dm_dram_clock_change_unsupported;
 	}
 
-	*StutterExitWatermark = SRExitTime + ExtraLatency + 10 / DCFCLKDeepSleep;
-	*StutterEnterPlusExitWatermark = (SREnterPlusExitTime + ExtraLatency + 10 / DCFCLKDeepSleep);
-	*Z8StutterExitWatermark = SRExitZ8Time + ExtraLatency + 10 / DCFCLKDeepSleep;
-	*Z8StutterEnterPlusExitWatermark = SREnterPlusExitZ8Time + ExtraLatency + 10 / DCFCLKDeepSleep;
+	*StutterExitWatermark = v->SRExitTime + ExtraLatency + 10 / DCFCLKDeepSleep;
+	*StutterEnterPlusExitWatermark = (v->SREnterPlusExitTime + ExtraLatency + 10 / DCFCLKDeepSleep);
+	*Z8StutterExitWatermark = v->SRExitZ8Time + ExtraLatency + 10 / DCFCLKDeepSleep;
+	*Z8StutterEnterPlusExitWatermark = v->SREnterPlusExitZ8Time + ExtraLatency + 10 / DCFCLKDeepSleep;
 
 #ifdef __DML_VBA_DEBUG__
 	dml_print("DML::%s: StutterExitWatermark = %f\n", __func__, *StutterExitWatermark);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.c
@@ -738,7 +738,7 @@
 		display_data_rq_sizing_params_st *rq_sizing_param,
 		display_data_rq_dlg_params_st *rq_dlg_param,
 		display_data_rq_misc_params_st *rq_misc_param,
-		const display_pipe_params_st pipe_param,
+		const display_pipe_params_st *pipe_param,
 		bool is_chroma,
 		bool is_alpha)
 {
@@ -752,33 +752,33 @@
 
 	// FIXME check if ppe apply for both luma and chroma in 422 case
 	if (is_chroma | is_alpha) {
-		vp_width = pipe_param.src.viewport_width_c / ppe;
-		vp_height = pipe_param.src.viewport_height_c;
-		data_pitch = pipe_param.src.data_pitch_c;
-		meta_pitch = pipe_param.src.meta_pitch_c;
-		surface_height = pipe_param.src.surface_height_y / 2.0;
+		vp_width = pipe_param->src.viewport_width_c / ppe;
+		vp_height = pipe_param->src.viewport_height_c;
+		data_pitch = pipe_param->src.data_pitch_c;
+		meta_pitch = pipe_param->src.meta_pitch_c;
+		surface_height = pipe_param->src.surface_height_y / 2.0;
 	} else {
-		vp_width = pipe_param.src.viewport_width / ppe;
-		vp_height = pipe_param.src.viewport_height;
-		data_pitch = pipe_param.src.data_pitch;
-		meta_pitch = pipe_param.src.meta_pitch;
-		surface_height = pipe_param.src.surface_height_y;
+		vp_width = pipe_param->src.viewport_width / ppe;
+		vp_height = pipe_param->src.viewport_height;
+		data_pitch = pipe_param->src.data_pitch;
+		meta_pitch = pipe_param->src.meta_pitch;
+		surface_height = pipe_param->src.surface_height_y;
 	}
 
-	if (pipe_param.dest.odm_combine) {
+	if (pipe_param->dest.odm_combine) {
 		unsigned int access_dir;
 		unsigned int full_src_vp_width;
 		unsigned int hactive_odm;
 		unsigned int src_hactive_odm;
 
-		access_dir = (pipe_param.src.source_scan == dm_vert); // vp access direction: horizontal or vertical accessed
-		hactive_odm = pipe_param.dest.hactive / ((unsigned int) pipe_param.dest.odm_combine * 2);
+		access_dir = (pipe_param->src.source_scan == dm_vert); // vp access direction: horizontal or vertical accessed
+		hactive_odm = pipe_param->dest.hactive / ((unsigned int) pipe_param->dest.odm_combine * 2);
 		if (is_chroma) {
-			full_src_vp_width = pipe_param.scale_ratio_depth.hscl_ratio_c * pipe_param.dest.full_recout_width;
-			src_hactive_odm = pipe_param.scale_ratio_depth.hscl_ratio_c * hactive_odm;
+			full_src_vp_width = pipe_param->scale_ratio_depth.hscl_ratio_c * pipe_param->dest.full_recout_width;
+			src_hactive_odm = pipe_param->scale_ratio_depth.hscl_ratio_c * hactive_odm;
 		} else {
-			full_src_vp_width = pipe_param.scale_ratio_depth.hscl_ratio * pipe_param.dest.full_recout_width;
-			src_hactive_odm = pipe_param.scale_ratio_depth.hscl_ratio * hactive_odm;
+			full_src_vp_width = pipe_param->scale_ratio_depth.hscl_ratio * pipe_param->dest.full_recout_width;
+			src_hactive_odm = pipe_param->scale_ratio_depth.hscl_ratio * hactive_odm;
 		}
 
 		if (access_dir == 0) {
@@ -808,7 +808,7 @@
 	rq_sizing_param->meta_chunk_bytes = 2048;
 	rq_sizing_param->min_meta_chunk_bytes = 256;
 
-	if (pipe_param.src.hostvm)
+	if (pipe_param->src.hostvm)
 		rq_sizing_param->mpte_group_bytes = 512;
 	else
 		rq_sizing_param->mpte_group_bytes = 2048;
@@ -822,38 +822,38 @@
 			vp_height,
 			data_pitch,
 			meta_pitch,
-			pipe_param.src.source_format,
-			pipe_param.src.sw_mode,
-			pipe_param.src.macro_tile_size,
-			pipe_param.src.source_scan,
-			pipe_param.src.hostvm,
+			pipe_param->src.source_format,
+			pipe_param->src.sw_mode,
+			pipe_param->src.macro_tile_size,
+			pipe_param->src.source_scan,
+			pipe_param->src.hostvm,
 			is_chroma,
 			surface_height);
 }
 
-static void dml_rq_dlg_get_rq_params(struct display_mode_lib *mode_lib, display_rq_params_st *rq_param, const display_pipe_params_st pipe_param)
+static void dml_rq_dlg_get_rq_params(struct display_mode_lib *mode_lib, display_rq_params_st *rq_param, const display_pipe_params_st *pipe_param)
 {
 	// get param for luma surface
-	rq_param->yuv420 = pipe_param.src.source_format == dm_420_8 || pipe_param.src.source_format == dm_420_10 || pipe_param.src.source_format == dm_rgbe_alpha
-			|| pipe_param.src.source_format == dm_420_12;
+	rq_param->yuv420 = pipe_param->src.source_format == dm_420_8 || pipe_param->src.source_format == dm_420_10 || pipe_param->src.source_format == dm_rgbe_alpha
+			|| pipe_param->src.source_format == dm_420_12;
 
-	rq_param->yuv420_10bpc = pipe_param.src.source_format == dm_420_10;
+	rq_param->yuv420_10bpc = pipe_param->src.source_format == dm_420_10;
 
-	rq_param->rgbe_alpha = (pipe_param.src.source_format == dm_rgbe_alpha) ? 1 : 0;
+	rq_param->rgbe_alpha = (pipe_param->src.source_format == dm_rgbe_alpha) ? 1 : 0;
 
 	get_surf_rq_param(mode_lib, &(rq_param->sizing.rq_l), &(rq_param->dlg.rq_l), &(rq_param->misc.rq_l), pipe_param, 0, 0);
 
-	if (is_dual_plane((enum source_format_class) (pipe_param.src.source_format))) {
+	if (is_dual_plane((enum source_format_class) (pipe_param->src.source_format))) {
 		// get param for chroma surface
 		get_surf_rq_param(mode_lib, &(rq_param->sizing.rq_c), &(rq_param->dlg.rq_c), &(rq_param->misc.rq_c), pipe_param, 1, rq_param->rgbe_alpha);
 	}
 
 	// calculate how to split the det buffer space between luma and chroma
-	handle_det_buf_split(mode_lib, rq_param, pipe_param.src);
+	handle_det_buf_split(mode_lib, rq_param, pipe_param->src);
 	print__rq_params_st(mode_lib, *rq_param);
 }
 
-void dml31_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib, display_rq_regs_st *rq_regs, const display_pipe_params_st pipe_param)
+void dml31_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib, display_rq_regs_st *rq_regs, const display_pipe_params_st *pipe_param)
 {
 	display_rq_params_st rq_param = {0};
 
@@ -1677,7 +1677,7 @@
 		struct display_mode_lib *mode_lib,
 		display_dlg_regs_st *dlg_regs,
 		display_ttu_regs_st *ttu_regs,
-		display_e2e_pipe_params_st *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int num_pipes,
 		const unsigned int pipe_idx,
 		const bool cstate_en,
@@ -1704,7 +1704,7 @@
 	// system parameter calculation done
 
 	dml_print("DML_DLG: Calculation for pipe[%d] start\n\n", pipe_idx);
-	dml_rq_dlg_get_rq_params(mode_lib, &rq_param, e2e_pipe_param[pipe_idx].pipe);
+	dml_rq_dlg_get_rq_params(mode_lib, &rq_param, &e2e_pipe_param[pipe_idx].pipe);
 	dml_rq_dlg_get_dlg_params(
 			mode_lib,
 			e2e_pipe_param,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.h
@@ -41,7 +41,7 @@
 //            See also: <display_rq_regs_st>
 void dml31_rq_dlg_get_rq_reg(struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param);
+		const display_pipe_params_st *pipe_param);
 
 // Function: dml_rq_dlg_get_dlg_reg
 //   Calculate and return DLG and TTU register struct given the system setting
@@ -57,7 +57,7 @@
 void dml31_rq_dlg_get_dlg_reg(struct display_mode_lib             *mode_lib,
 		display_dlg_regs_st          *dlg_regs,
 		display_ttu_regs_st          *ttu_regs,
-		display_e2e_pipe_params_st   *e2e_pipe_param,
+		const display_e2e_pipe_params_st *e2e_pipe_param,
 		const unsigned int            num_pipes,
 		const unsigned int            pipe_idx,
 		const bool                    cstate_en,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/display_mode_enums.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/display_mode_enums.h
@@ -80,11 +80,11 @@
 	dm_sw_SPARE_13 = 24,
 	dm_sw_64kb_s_x = 25,
 	dm_sw_64kb_d_x = 26,
-	dm_sw_SPARE_14 = 27,
+	dm_sw_64kb_r_x = 27,
 	dm_sw_SPARE_15 = 28,
 	dm_sw_var_s_x = 29,
 	dm_sw_var_d_x = 30,
-	dm_sw_64kb_r_x,
+	dm_sw_var_r_x = 31,
 	dm_sw_gfx7_2d_thin_l_vp,
 	dm_sw_gfx7_2d_thin_gl,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/display_mode_lib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/display_mode_lib.h
@@ -49,7 +49,7 @@
 			struct display_mode_lib *mode_lib,
 			display_dlg_regs_st *dlg_regs,
 			display_ttu_regs_st *ttu_regs,
-			display_e2e_pipe_params_st *e2e_pipe_param,
+			const display_e2e_pipe_params_st *e2e_pipe_param,
 			const unsigned int num_pipes,
 			const unsigned int pipe_idx,
 			const bool cstate_en,
@@ -60,7 +60,7 @@
 	void (*rq_dlg_get_rq_reg)(
 		struct display_mode_lib *mode_lib,
 		display_rq_regs_st *rq_regs,
-		const display_pipe_params_st pipe_param);
+		const display_pipe_params_st *pipe_param);
 	void (*recalculate)(struct display_mode_lib *mode_lib);
 	void (*validate)(struct display_mode_lib *mode_lib);
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.c
@@ -867,11 +867,30 @@
 	}
 }
 
+static unsigned int get_pipe_idx(struct display_mode_lib *mode_lib, unsigned int plane_idx)
+{
+	int pipe_idx = -1;
+	int i;
+
+	ASSERT(plane_idx < DC__NUM_DPP__MAX);
+
+	for (i = 0; i < DC__NUM_DPP__MAX ; i++) {
+		if (plane_idx == mode_lib->vba.pipe_plane[i]) {
+			pipe_idx = i;
+			break;
+		}
+	}
+	ASSERT(pipe_idx >= 0);
+
+	return pipe_idx;
+}
+
 void ModeSupportAndSystemConfiguration(struct display_mode_lib *mode_lib)
 {
 	soc_bounding_box_st *soc = &mode_lib->vba.soc;
 	unsigned int k;
 	unsigned int total_pipes = 0;
+	unsigned int pipe_idx = 0;
 
 	mode_lib->vba.VoltageLevel = mode_lib->vba.cache_pipes[0].clks_cfg.voltage;
 	mode_lib->vba.ReturnBW = mode_lib->vba.ReturnBWPerState[mode_lib->vba.VoltageLevel][mode_lib->vba.maxMpcComb];
@@ -892,6 +911,11 @@
 
 	// Total Available Pipes Support Check
 	for (k = 0; k < mode_lib->vba.NumberOfActivePlanes; ++k) {
+		pipe_idx = get_pipe_idx(mode_lib, k);
+		if (pipe_idx == -1) {
+			ASSERT(0);
+			continue; // skip inactive planes
+		}
 		total_pipes += mode_lib->vba.DPPPerPlane[k];
 	}
 	ASSERT(total_pipes <= DC__NUM_DPP__MAX);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dml_inline_defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dml_inline_defs.h
@@ -66,11 +66,15 @@
 
 static inline double dml_ceil(double a, double granularity)
 {
+	if (granularity == 0)
+		return 0;
 	return (double) dcn_bw_ceil2(a, granularity);
 }
 
 static inline double dml_floor(double a, double granularity)
 {
+	if (granularity == 0)
+		return 0;
 	return (double) dcn_bw_floor2(a, granularity);
 }
 
@@ -119,11 +123,15 @@
 
 static inline double dml_ceil_ex(double x, double granularity)
 {
+	if (granularity == 0)
+		return 0;
 	return (double) dcn_bw_ceil2(x, granularity);
 }
 
 static inline double dml_floor_ex(double x, double granularity)
 {
+	if (granularity == 0)
+		return 0;
 	return (double) dcn_bw_floor2(x, granularity);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dsc/qp_tables.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dsc/qp_tables.h
@@ -0,0 +1,704 @@
+
+/*
+ * Copyright 2017 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+
+const qp_table   qp_table_422_10bpc_min = {
+	{   6, { 0, 4, 5, 6, 6, 6, 6, 7, 7, 8, 9, 9, 9, 12, 16} },
+	{ 6.5, { 0, 4, 5, 6, 6, 6, 6, 7, 7, 8, 9, 9, 9, 12, 16} },
+	{   7, { 0, 4, 5, 6, 6, 6, 6, 7, 7, 7, 9, 9, 9, 11, 15} },
+	{ 7.5, { 0, 2, 4, 6, 6, 6, 6, 7, 7, 7, 8, 9, 9, 11, 15} },
+	{   8, { 0, 2, 3, 5, 5, 6, 6, 7, 7, 7, 8, 8, 9, 11, 14} },
+	{ 8.5, { 0, 2, 3, 4, 5, 5, 5, 6, 6, 7, 8, 8, 9, 11, 14} },
+	{   9, { 0, 2, 3, 4, 5, 5, 5, 6, 6, 7, 8, 8, 9, 11, 13} },
+	{ 9.5, { 0, 2, 3, 4, 4, 5, 5, 6, 6, 7, 8, 8, 9, 11, 13} },
+	{  10, { 0, 2, 2, 3, 4, 5, 5, 6, 6, 7, 8, 8, 9, 11, 12} },
+	{10.5, { 0, 2, 2, 3, 4, 4, 5, 6, 6, 7, 8, 8, 9, 11, 12} },
+	{  11, { 0, 2, 2, 3, 4, 4, 5, 6, 6, 7, 8, 8, 9, 10, 11} },
+	{11.5, { 0, 2, 2, 3, 4, 4, 5, 5, 6, 7, 7, 8, 8, 10, 11} },
+	{  12, { 0, 2, 2, 3, 4, 4, 5, 5, 6, 6, 7, 7, 8, 9, 10} },
+	{12.5, { 0, 1, 2, 2, 4, 4, 4, 5, 5, 6, 6, 7, 8, 9, 10} },
+	{  13, { 0, 1, 2, 2, 4, 4, 4, 5, 5, 6, 6, 6, 8, 8, 9} },
+	{13.5, { 0, 1, 2, 2, 3, 4, 4, 4, 5, 6, 6, 6, 7, 8, 9} },
+	{  14, { 0, 1, 2, 2, 3, 4, 4, 4, 4, 5, 5, 6, 7, 7, 8} },
+	{14.5, { 0, 1, 1, 2, 3, 3, 4, 4, 4, 5, 5, 6, 6, 7, 8} },
+	{  15, { 0, 1, 1, 2, 2, 3, 3, 4, 4, 4, 5, 6, 6, 6, 8} },
+	{15.5, { 0, 0, 1, 1, 2, 3, 3, 3, 4, 4, 5, 5, 5, 6, 7} },
+	{  16, { 0, 0, 1, 1, 2, 3, 3, 3, 4, 4, 5, 5, 5, 5, 7} },
+	{16.5, { 0, 0, 0, 1, 1, 2, 2, 3, 3, 3, 3, 4, 4, 5, 6} },
+	{  17, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 6} },
+	{17.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 3, 4, 5} },
+	{  18, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 5} },
+	{18.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 3, 5} },
+	{  19, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 2, 4} },
+	{19.5, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 2, 4} },
+	{  20, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 3} }
+};
+
+
+const qp_table   qp_table_444_8bpc_max = {
+	{   6, { 4, 6, 8, 8, 9, 9, 9, 10, 11, 12, 12, 12, 12, 13, 15} },
+	{ 6.5, { 4, 6, 7, 8, 8, 8, 9, 10, 11, 11, 12, 12, 12, 13, 15} },
+	{   7, { 4, 5, 7, 7, 8, 8, 8, 9, 10, 11, 11, 12, 12, 13, 14} },
+	{ 7.5, { 4, 5, 6, 7, 7, 8, 8, 9, 10, 10, 11, 11, 12, 13, 14} },
+	{   8, { 4, 4, 5, 6, 7, 7, 7, 8, 9, 10, 10, 11, 11, 12, 13} },
+	{ 8.5, { 4, 4, 5, 6, 7, 7, 7, 8, 9, 10, 10, 11, 11, 12, 13} },
+	{   9, { 3, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 10, 11, 11, 13} },
+	{ 9.5, { 3, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 10, 11, 11, 13} },
+	{  10, { 3, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 10, 11, 11, 12} },
+	{10.5, { 3, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 10, 10, 11, 12} },
+	{  11, { 2, 4, 5, 6, 7, 7, 7, 8, 8, 9, 9, 9, 10, 10, 11} },
+	{11.5, { 2, 4, 5, 6, 7, 7, 7, 8, 8, 9, 9, 9, 9, 10, 11} },
+	{  12, { 2, 3, 4, 5, 6, 6, 7, 8, 8, 9, 9, 9, 9, 10, 11} },
+	{12.5, { 2, 3, 4, 5, 6, 6, 6, 7, 7, 8, 8, 9, 9, 10, 11} },
+	{  13, { 1, 3, 4, 5, 5, 6, 6, 7, 7, 8, 8, 8, 8, 9, 10} },
+	{13.5, { 1, 2, 3, 4, 4, 5, 5, 6, 6, 7, 7, 8, 8, 9, 10} },
+	{  14, { 1, 2, 2, 3, 4, 4, 4, 5, 6, 6, 7, 8, 8, 8, 10} },
+	{14.5, { 0, 1, 2, 3, 3, 4, 4, 5, 5, 6, 6, 7, 7, 8, 9} },
+	{  15, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 7, 7, 8, 9} },
+	{15.5, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 7, 7, 8, 9} },
+	{  16, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 5, 6, 6, 7, 8} },
+	{16.5, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 5, 6, 6, 7, 8} },
+	{  17, { 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 6, 8} },
+	{17.5, { 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 6, 8} },
+	{  18, { 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 6, 7} },
+	{18.5, { 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 6, 7} },
+	{  19, { 0, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 4, 5, 6} },
+	{19.5, { 0, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 4, 5, 6} },
+	{  20, { 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 3, 3, 4, 6} },
+	{20.5, { 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 3, 3, 4, 6} },
+	{  21, { 0, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 4, 5} },
+	{21.5, { 0, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 4, 5} },
+	{  22, { 0, 0, 0, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 3, 5} },
+	{22.5, { 0, 0, 0, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 3, 4} },
+	{  23, { 0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 4} },
+	{23.5, { 0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 4} },
+	{  24, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 1, 2, 4} }
+};
+
+
+const qp_table   qp_table_420_12bpc_max = {
+	{   4, {11, 12, 13, 14, 15, 15, 15, 16, 17, 18, 18, 19, 19, 21, 22} },
+	{ 4.5, {10, 11, 12, 13, 14, 15, 15, 16, 17, 18, 18, 19, 19, 20, 21} },
+	{   5, { 9, 11, 12, 13, 14, 15, 15, 16, 17, 17, 18, 18, 19, 20, 21} },
+	{ 5.5, { 8, 10, 11, 12, 13, 14, 15, 16, 16, 17, 17, 18, 18, 19, 20} },
+	{   6, { 6, 9, 11, 12, 13, 14, 15, 16, 16, 17, 17, 17, 17, 18, 19} },
+	{ 6.5, { 6, 8, 10, 11, 11, 13, 14, 15, 15, 16, 16, 17, 17, 18, 19} },
+	{   7, { 5, 7, 9, 10, 10, 12, 13, 14, 14, 15, 16, 16, 17, 17, 18} },
+	{ 7.5, { 5, 7, 8, 9, 9, 11, 12, 13, 14, 14, 15, 15, 16, 16, 17} },
+	{   8, { 4, 6, 7, 8, 8, 10, 11, 12, 13, 13, 14, 15, 15, 16, 17} },
+	{ 8.5, { 3, 6, 6, 7, 7, 10, 11, 12, 13, 13, 14, 14, 15, 15, 16} },
+	{   9, { 3, 5, 6, 7, 7, 10, 11, 12, 12, 13, 13, 14, 14, 14, 15} },
+	{ 9.5, { 2, 5, 6, 6, 7, 9, 10, 11, 12, 12, 13, 13, 13, 14, 15} },
+	{  10, { 2, 4, 5, 6, 7, 8, 9, 10, 11, 12, 12, 13, 13, 13, 15} },
+	{10.5, { 2, 3, 5, 5, 6, 7, 8, 9, 11, 11, 12, 12, 12, 12, 14} },
+	{  11, { 1, 3, 4, 5, 6, 6, 7, 9, 10, 11, 11, 11, 12, 12, 13} },
+	{11.5, { 1, 2, 3, 4, 5, 6, 6, 8, 9, 10, 10, 11, 11, 11, 13} },
+	{  12, { 1, 1, 3, 3, 4, 5, 6, 7, 8, 9, 9, 10, 10, 10, 12} },
+	{12.5, { 1, 1, 2, 3, 4, 5, 6, 7, 8, 8, 9, 9, 9, 10, 11} },
+	{  13, { 1, 1, 1, 2, 4, 4, 6, 6, 7, 8, 8, 9, 9, 9, 11} },
+	{13.5, { 1, 1, 1, 2, 3, 4, 5, 5, 6, 7, 8, 8, 8, 9, 11} },
+	{  14, { 1, 1, 1, 2, 3, 4, 4, 5, 6, 6, 7, 8, 8, 8, 10} },
+	{14.5, { 0, 1, 1, 1, 2, 3, 4, 4, 5, 5, 6, 7, 7, 7, 9} },
+	{  15, { 0, 1, 1, 1, 1, 2, 3, 3, 5, 5, 5, 6, 6, 7, 9} },
+	{15.5, { 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 8} },
+	{  16, { 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 7} },
+	{16.5, { 0, 0, 0, 0, 0, 1, 2, 2, 2, 3, 3, 4, 4, 5, 7} },
+	{  17, { 0, 0, 0, 0, 0, 0, 1, 2, 2, 2, 3, 3, 3, 4, 6} },
+	{17.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 6} },
+	{  18, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 5} }
+};
+
+
+const qp_table   qp_table_444_10bpc_min = {
+	{   6, { 0, 4, 7, 7, 9, 9, 9, 9, 9, 10, 10, 10, 10, 12, 18} },
+	{ 6.5, { 0, 4, 6, 7, 8, 8, 9, 9, 9, 9, 10, 10, 10, 12, 18} },
+	{   7, { 0, 4, 6, 6, 8, 8, 8, 8, 8, 9, 9, 10, 10, 12, 17} },
+	{ 7.5, { 0, 4, 6, 6, 7, 8, 8, 8, 8, 8, 9, 9, 10, 12, 17} },
+	{   8, { 0, 4, 5, 5, 7, 7, 7, 7, 7, 8, 9, 9, 9, 12, 16} },
+	{ 8.5, { 0, 4, 5, 5, 7, 7, 7, 7, 7, 8, 9, 9, 9, 12, 16} },
+	{   9, { 0, 4, 5, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 12, 16} },
+	{ 9.5, { 0, 4, 5, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 12, 16} },
+	{  10, { 0, 4, 5, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 12, 15} },
+	{10.5, { 0, 4, 5, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 12, 15} },
+	{  11, { 0, 3, 5, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 11, 14} },
+	{11.5, { 0, 3, 5, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 11, 14} },
+	{  12, { 0, 2, 4, 4, 6, 6, 7, 7, 7, 7, 9, 9, 9, 11, 14} },
+	{12.5, { 0, 2, 4, 4, 6, 6, 7, 7, 7, 7, 8, 9, 9, 11, 14} },
+	{  13, { 0, 2, 4, 4, 5, 6, 7, 7, 7, 7, 8, 9, 9, 11, 13} },
+	{13.5, { 0, 2, 3, 4, 5, 6, 6, 7, 7, 7, 8, 9, 9, 11, 13} },
+	{  14, { 0, 2, 3, 4, 5, 5, 6, 6, 7, 7, 8, 9, 9, 11, 13} },
+	{14.5, { 0, 2, 3, 4, 5, 5, 6, 6, 6, 7, 7, 8, 9, 11, 12} },
+	{  15, { 0, 2, 3, 4, 4, 5, 5, 6, 6, 6, 7, 8, 9, 11, 12} },
+	{15.5, { 0, 2, 3, 4, 4, 5, 5, 6, 6, 6, 7, 8, 9, 11, 12} },
+	{  16, { 0, 2, 3, 4, 4, 5, 5, 6, 6, 6, 7, 8, 8, 10, 11} },
+	{16.5, { 0, 1, 2, 3, 4, 5, 5, 6, 6, 6, 7, 8, 8, 10, 11} },
+	{  17, { 0, 1, 2, 3, 3, 4, 5, 5, 5, 6, 6, 7, 8, 9, 11} },
+	{17.5, { 0, 1, 2, 3, 3, 4, 4, 5, 5, 6, 6, 7, 8, 9, 11} },
+	{  18, { 0, 1, 2, 3, 3, 4, 4, 5, 5, 6, 6, 7, 8, 9, 10} },
+	{18.5, { 0, 1, 2, 3, 3, 4, 4, 5, 5, 6, 6, 7, 8, 9, 10} },
+	{  19, { 0, 1, 1, 2, 3, 3, 3, 4, 5, 6, 6, 7, 7, 8, 9} },
+	{19.5, { 0, 1, 1, 2, 3, 3, 3, 4, 5, 6, 6, 7, 7, 8, 9} },
+	{  20, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 5, 6, 6, 7, 9} },
+	{20.5, { 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6, 7, 9} },
+	{  21, { 0, 1, 1, 2, 2, 3, 3, 4, 4, 4, 5, 6, 6, 7, 9} },
+	{21.5, { 0, 1, 1, 2, 2, 2, 3, 4, 4, 4, 5, 6, 6, 7, 8} },
+	{  22, { 0, 0, 1, 2, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6, 8} },
+	{22.5, { 0, 0, 1, 2, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6, 7} },
+	{  23, { 0, 0, 1, 2, 2, 2, 3, 3, 3, 3, 5, 5, 5, 5, 7} },
+	{23.5, { 0, 0, 0, 2, 2, 2, 3, 3, 3, 3, 5, 5, 5, 5, 7} },
+	{  24, { 0, 0, 0, 1, 1, 2, 3, 3, 3, 3, 4, 4, 4, 5, 7} },
+	{24.5, { 0, 0, 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 7} },
+	{  25, { 0, 0, 0, 0, 1, 2, 2, 2, 3, 3, 4, 4, 4, 4, 6} },
+	{25.5, { 0, 0, 0, 0, 1, 2, 2, 2, 3, 3, 3, 4, 4, 4, 6} },
+	{  26, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 5} },
+	{26.5, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 3, 3, 5} },
+	{  27, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 5} },
+	{27.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 5} },
+	{  28, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 4} },
+	{28.5, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 4} },
+	{  29, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 3} },
+	{29.5, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3} },
+	{  30, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3} }
+};
+
+
+const qp_table   qp_table_420_8bpc_max = {
+	{   4, { 4, 4, 5, 6, 7, 7, 7, 8, 9, 10, 10, 11, 11, 13, 14} },
+	{ 4.5, { 4, 4, 5, 6, 7, 7, 7, 8, 9, 10, 10, 11, 11, 12, 13} },
+	{   5, { 3, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 10, 11, 12, 13} },
+	{ 5.5, { 3, 4, 5, 6, 7, 7, 7, 8, 8, 9, 9, 10, 10, 11, 12} },
+	{   6, { 2, 4, 5, 6, 7, 7, 7, 8, 8, 9, 9, 9, 9, 10, 11} },
+	{ 6.5, { 2, 3, 4, 5, 5, 6, 6, 7, 7, 8, 8, 9, 9, 10, 11} },
+	{   7, { 1, 2, 3, 4, 4, 5, 5, 6, 6, 7, 8, 8, 9, 9, 10} },
+	{ 7.5, { 1, 2, 2, 3, 3, 4, 4, 5, 6, 6, 7, 7, 8, 8, 9} },
+	{   8, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 7, 7, 8, 9} },
+	{ 8.5, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 6, 7, 7, 8} },
+	{   9, { 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6, 6, 7} },
+	{ 9.5, { 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6, 7} },
+	{  10, { 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6} },
+	{10.5, { 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 4, 6} },
+	{  11, { 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 5} },
+	{11.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 3, 4, 5} },
+	{  12, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 4} }
+};
+
+
+const qp_table   qp_table_444_8bpc_min = {
+	{   6, { 0, 1, 3, 3, 5, 5, 5, 5, 5, 6, 6, 6, 6, 9, 14} },
+	{ 6.5, { 0, 1, 2, 3, 4, 4, 5, 5, 5, 5, 6, 6, 6, 9, 14} },
+	{   7, { 0, 0, 2, 2, 4, 4, 4, 4, 4, 5, 5, 6, 6, 9, 13} },
+	{ 7.5, { 0, 0, 2, 2, 3, 4, 4, 4, 4, 4, 5, 5, 6, 9, 13} },
+	{   8, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 4, 5, 5, 5, 8, 12} },
+	{ 8.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 4, 5, 5, 5, 8, 12} },
+	{   9, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 12} },
+	{ 9.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 12} },
+	{  10, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 11} },
+	{10.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 11} },
+	{  11, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 10} },
+	{11.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 10} },
+	{  12, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 10} },
+	{12.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 4, 5, 5, 7, 10} },
+	{  13, { 0, 0, 1, 1, 2, 3, 3, 3, 3, 3, 4, 5, 5, 7, 9} },
+	{13.5, { 0, 0, 0, 1, 1, 2, 2, 2, 2, 3, 4, 5, 5, 7, 9} },
+	{  14, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 4, 5, 5, 7, 9} },
+	{14.5, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{  15, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{15.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{  16, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 6, 7} },
+	{16.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 6, 7} },
+	{  17, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 7} },
+	{17.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 7} },
+	{  18, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 6} },
+	{18.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 6} },
+	{  19, { 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 3, 3, 4, 5} },
+	{19.5, { 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 3, 3, 4, 5} },
+	{  20, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 2, 2, 3, 5} },
+	{20.5, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 2, 2, 3, 5} },
+	{  21, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 3, 4} },
+	{21.5, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 3, 4} },
+	{  22, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 4} },
+	{22.5, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 3} },
+	{  23, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3} },
+	{23.5, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3} },
+	{  24, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 3} }
+};
+
+
+const qp_table   qp_table_444_12bpc_min = {
+	{   6, { 0, 5, 11, 11, 13, 13, 13, 13, 13, 14, 14, 14, 14, 17, 22} },
+	{ 6.5, { 0, 5, 10, 11, 12, 12, 13, 13, 13, 13, 14, 14, 14, 17, 22} },
+	{   7, { 0, 5, 10, 10, 12, 12, 12, 12, 12, 13, 13, 14, 14, 17, 21} },
+	{ 7.5, { 0, 5, 9, 10, 11, 12, 12, 12, 12, 12, 13, 13, 14, 17, 21} },
+	{   8, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 12, 13, 13, 13, 16, 20} },
+	{ 8.5, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 12, 13, 13, 13, 16, 20} },
+	{   9, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 20} },
+	{ 9.5, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 20} },
+	{  10, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 19} },
+	{10.5, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 19} },
+	{  11, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{11.5, { 0, 4, 8, 9, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{  12, { 0, 4, 7, 8, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{12.5, { 0, 4, 7, 8, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{  13, { 0, 4, 7, 8, 9, 11, 11, 11, 11, 11, 13, 13, 13, 15, 17} },
+	{13.5, { 0, 3, 6, 7, 9, 10, 10, 11, 11, 11, 12, 13, 13, 15, 17} },
+	{  14, { 0, 3, 5, 6, 9, 9, 9, 10, 11, 11, 12, 13, 13, 15, 17} },
+	{14.5, { 0, 2, 5, 6, 8, 9, 9, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{  15, { 0, 2, 4, 6, 7, 8, 9, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{15.5, { 0, 2, 4, 6, 7, 8, 9, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{  16, { 0, 2, 4, 6, 7, 8, 9, 10, 11, 11, 11, 12, 12, 14, 15} },
+	{16.5, { 0, 2, 3, 5, 7, 8, 9, 10, 11, 11, 11, 12, 12, 14, 15} },
+	{  17, { 0, 2, 3, 5, 5, 6, 9, 9, 10, 10, 11, 11, 12, 13, 15} },
+	{17.5, { 0, 2, 3, 5, 5, 6, 8, 9, 10, 10, 11, 11, 12, 13, 15} },
+	{  18, { 0, 2, 3, 5, 5, 6, 8, 9, 10, 10, 11, 11, 12, 13, 14} },
+	{18.5, { 0, 2, 3, 5, 5, 6, 8, 9, 10, 10, 11, 11, 12, 13, 14} },
+	{  19, { 0, 1, 2, 4, 5, 5, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{19.5, { 0, 1, 2, 4, 5, 5, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{  20, { 0, 1, 2, 3, 4, 5, 7, 8, 8, 8, 9, 10, 10, 11, 13} },
+	{20.5, { 0, 1, 2, 3, 4, 5, 6, 7, 7, 8, 9, 10, 10, 11, 13} },
+	{  21, { 0, 1, 2, 3, 4, 5, 5, 7, 7, 8, 9, 10, 10, 11, 13} },
+	{21.5, { 0, 1, 2, 3, 3, 4, 5, 7, 7, 8, 9, 10, 10, 11, 12} },
+	{  22, { 0, 0, 1, 3, 3, 4, 5, 6, 7, 8, 9, 9, 9, 10, 12} },
+	{22.5, { 0, 0, 1, 3, 3, 4, 5, 6, 7, 8, 9, 9, 9, 10, 11} },
+	{  23, { 0, 0, 1, 3, 3, 4, 5, 6, 6, 7, 9, 9, 9, 9, 11} },
+	{23.5, { 0, 0, 1, 3, 3, 4, 5, 6, 6, 7, 9, 9, 9, 9, 11} },
+	{  24, { 0, 0, 1, 2, 3, 4, 5, 6, 6, 7, 8, 8, 8, 9, 11} },
+	{24.5, { 0, 0, 1, 2, 3, 4, 4, 6, 6, 7, 8, 8, 8, 9, 11} },
+	{  25, { 0, 0, 1, 2, 3, 4, 4, 5, 6, 7, 8, 8, 8, 8, 10} },
+	{25.5, { 0, 0, 1, 2, 3, 4, 4, 5, 6, 6, 7, 8, 8, 8, 10} },
+	{  26, { 0, 0, 1, 2, 2, 3, 4, 5, 5, 6, 7, 7, 7, 7, 9} },
+	{26.5, { 0, 0, 1, 2, 2, 3, 4, 5, 5, 5, 7, 7, 7, 7, 9} },
+	{  27, { 0, 0, 1, 2, 2, 3, 4, 4, 5, 5, 6, 7, 7, 7, 9} },
+	{27.5, { 0, 0, 1, 1, 2, 2, 4, 4, 4, 5, 6, 7, 7, 7, 9} },
+	{  28, { 0, 0, 0, 1, 1, 2, 3, 4, 4, 4, 6, 6, 6, 7, 9} },
+	{28.5, { 0, 0, 0, 1, 1, 2, 3, 3, 4, 4, 5, 6, 6, 6, 8} },
+	{  29, { 0, 0, 0, 1, 1, 2, 3, 3, 4, 4, 5, 5, 6, 6, 8} },
+	{29.5, { 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 5, 5, 6, 6, 7} },
+	{  30, { 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 5, 5, 5, 5, 7} },
+	{30.5, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 4, 4, 4, 5, 7} },
+	{  31, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 4, 4, 4, 5, 7} },
+	{31.5, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 7} },
+	{  32, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 3, 3, 4, 6} },
+	{32.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 3, 3, 3, 4, 6} },
+	{  33, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 5} },
+	{33.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 5} },
+	{  34, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 2, 2, 2, 3, 5} },
+	{34.5, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 2, 2, 2, 3, 5} },
+	{  35, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 4} },
+	{35.5, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 4} },
+	{  36, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3} }
+};
+
+
+const qp_table   qp_table_420_12bpc_min = {
+	{   4, { 0, 4, 9, 10, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 21} },
+	{ 4.5, { 0, 4, 8, 9, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 20} },
+	{   5, { 0, 4, 8, 9, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 20} },
+	{ 5.5, { 0, 4, 7, 8, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 19} },
+	{   6, { 0, 4, 7, 8, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{ 6.5, { 0, 4, 6, 8, 9, 10, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{   7, { 0, 3, 5, 7, 9, 10, 10, 11, 11, 11, 13, 13, 13, 15, 17} },
+	{ 7.5, { 0, 3, 5, 7, 8, 9, 10, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{   8, { 0, 2, 4, 6, 7, 9, 9, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{ 8.5, { 0, 2, 4, 6, 6, 9, 9, 10, 11, 11, 12, 12, 13, 14, 15} },
+	{   9, { 0, 2, 4, 6, 6, 9, 9, 10, 10, 11, 11, 12, 13, 13, 14} },
+	{ 9.5, { 0, 2, 4, 5, 6, 8, 8, 9, 10, 10, 11, 12, 12, 13, 14} },
+	{  10, { 0, 2, 3, 5, 6, 7, 8, 8, 9, 10, 10, 12, 12, 12, 14} },
+	{10.5, { 0, 2, 3, 4, 5, 6, 7, 8, 9, 9, 10, 11, 11, 11, 13} },
+	{  11, { 0, 2, 3, 4, 5, 5, 6, 8, 8, 9, 9, 10, 11, 11, 12} },
+	{11.5, { 0, 1, 2, 3, 4, 5, 5, 7, 8, 8, 9, 10, 10, 10, 12} },
+	{  12, { 0, 0, 2, 2, 3, 4, 5, 6, 7, 8, 8, 9, 9, 9, 11} },
+	{12.5, { 0, 0, 1, 2, 3, 4, 5, 6, 7, 7, 8, 8, 8, 9, 10} },
+	{  13, { 0, 0, 0, 1, 3, 3, 5, 5, 6, 7, 7, 8, 8, 8, 10} },
+	{13.5, { 0, 0, 0, 1, 2, 3, 4, 4, 5, 6, 7, 7, 7, 8, 10} },
+	{  14, { 0, 0, 0, 1, 2, 3, 3, 4, 5, 5, 6, 7, 7, 7, 9} },
+	{14.5, { 0, 0, 0, 0, 1, 2, 3, 3, 4, 4, 5, 6, 6, 6, 8} },
+	{  15, { 0, 0, 0, 0, 0, 1, 2, 2, 4, 4, 4, 5, 5, 6, 8} },
+	{15.5, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 7} },
+	{  16, { 0, 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 6} },
+	{16.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 6} },
+	{  17, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 3, 5} },
+	{17.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 2, 3, 5} },
+	{  18, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 2, 4} }
+};
+
+
+const qp_table   qp_table_422_12bpc_min = {
+	{   6, { 0, 4, 9, 10, 11, 11, 11, 11, 11, 11, 13, 13, 13, 16, 20} },
+	{ 6.5, { 0, 4, 9, 10, 11, 11, 11, 11, 11, 11, 13, 13, 13, 16, 20} },
+	{   7, { 0, 4, 9, 10, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 19} },
+	{ 7.5, { 0, 4, 8, 10, 11, 11, 11, 11, 11, 11, 13, 13, 13, 15, 19} },
+	{   8, { 0, 4, 7, 8, 10, 11, 11, 11, 11, 11, 13, 13, 13, 15, 18} },
+	{ 8.5, { 0, 3, 6, 8, 9, 10, 10, 11, 11, 11, 12, 13, 13, 15, 18} },
+	{   9, { 0, 3, 5, 8, 9, 10, 10, 10, 11, 11, 12, 13, 13, 15, 17} },
+	{ 9.5, { 0, 3, 5, 7, 8, 9, 10, 10, 11, 11, 12, 13, 13, 15, 17} },
+	{  10, { 0, 2, 4, 6, 7, 9, 9, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{10.5, { 0, 2, 4, 6, 7, 8, 9, 10, 11, 11, 12, 13, 13, 15, 16} },
+	{  11, { 0, 2, 4, 6, 7, 8, 9, 10, 11, 11, 12, 12, 13, 14, 15} },
+	{11.5, { 0, 2, 4, 6, 7, 7, 9, 9, 10, 11, 11, 12, 12, 14, 15} },
+	{  12, { 0, 2, 4, 6, 6, 6, 8, 8, 9, 9, 11, 11, 12, 13, 14} },
+	{12.5, { 0, 1, 4, 5, 6, 6, 7, 8, 8, 9, 10, 11, 11, 13, 14} },
+	{  13, { 0, 1, 3, 4, 5, 5, 7, 8, 8, 9, 10, 10, 11, 12, 13} },
+	{13.5, { 0, 1, 3, 3, 4, 5, 7, 7, 8, 8, 10, 10, 10, 12, 13} },
+	{  14, { 0, 0, 2, 3, 4, 5, 6, 6, 7, 7, 9, 10, 10, 11, 12} },
+	{14.5, { 0, 0, 1, 3, 4, 4, 6, 6, 6, 7, 9, 9, 9, 11, 12} },
+	{  15, { 0, 0, 1, 3, 3, 4, 5, 6, 6, 6, 8, 9, 9, 10, 12} },
+	{15.5, { 0, 0, 1, 2, 3, 4, 5, 5, 6, 6, 8, 8, 8, 10, 11} },
+	{  16, { 0, 0, 1, 2, 3, 4, 5, 5, 6, 6, 8, 8, 8, 9, 11} },
+	{16.5, { 0, 0, 0, 2, 2, 3, 4, 5, 5, 5, 6, 7, 7, 9, 10} },
+	{  17, { 0, 0, 0, 1, 2, 2, 4, 4, 4, 5, 6, 6, 6, 8, 10} },
+	{17.5, { 0, 0, 0, 1, 2, 2, 3, 4, 4, 4, 5, 6, 6, 8, 9} },
+	{  18, { 0, 0, 0, 1, 2, 2, 3, 3, 3, 4, 5, 5, 6, 7, 9} },
+	{18.5, { 0, 0, 0, 1, 2, 2, 3, 3, 3, 3, 5, 5, 5, 7, 9} },
+	{  19, { 0, 0, 0, 1, 2, 2, 2, 3, 3, 3, 4, 4, 5, 6, 8} },
+	{19.5, { 0, 0, 0, 1, 1, 1, 2, 3, 3, 3, 4, 4, 4, 6, 8} },
+	{  20, { 0, 0, 0, 1, 1, 1, 2, 3, 3, 3, 4, 4, 4, 5, 7} },
+	{20.5, { 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 4, 5, 7} },
+	{  21, { 0, 0, 0, 0, 0, 1, 2, 2, 3, 3, 3, 4, 4, 4, 6} },
+	{21.5, { 0, 0, 0, 0, 0, 0, 1, 2, 2, 2, 3, 3, 3, 4, 6} },
+	{  22, { 0, 0, 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 6} },
+	{22.5, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 5} },
+	{  23, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 2, 3, 5} },
+	{23.5, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 4} },
+	{  24, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 4} }
+};
+
+
+const qp_table   qp_table_422_12bpc_max = {
+	{   6, {12, 12, 13, 14, 15, 15, 15, 16, 17, 18, 18, 19, 19, 20, 21} },
+	{ 6.5, {12, 12, 13, 14, 15, 15, 15, 16, 17, 18, 18, 19, 19, 20, 21} },
+	{   7, {11, 12, 13, 14, 15, 15, 15, 16, 17, 17, 18, 18, 19, 19, 20} },
+	{ 7.5, { 9, 10, 12, 14, 15, 15, 15, 16, 16, 17, 17, 18, 18, 19, 20} },
+	{   8, { 6, 9, 10, 12, 14, 15, 15, 16, 16, 17, 17, 17, 17, 18, 19} },
+	{ 8.5, { 6, 8, 9, 11, 13, 14, 14, 15, 15, 16, 16, 17, 17, 18, 19} },
+	{   9, { 5, 7, 8, 10, 12, 13, 13, 14, 14, 15, 15, 16, 16, 17, 18} },
+	{ 9.5, { 5, 7, 7, 9, 10, 12, 12, 13, 14, 14, 15, 15, 16, 17, 18} },
+	{  10, { 4, 6, 6, 8, 9, 11, 11, 12, 13, 13, 14, 15, 15, 16, 17} },
+	{10.5, { 4, 6, 6, 8, 9, 10, 11, 12, 13, 13, 14, 15, 15, 16, 17} },
+	{  11, { 4, 5, 6, 8, 9, 10, 11, 12, 13, 13, 14, 14, 15, 15, 16} },
+	{11.5, { 3, 5, 6, 8, 9, 9, 11, 11, 12, 13, 13, 14, 14, 15, 16} },
+	{  12, { 3, 5, 6, 8, 8, 8, 10, 10, 11, 11, 13, 13, 14, 14, 15} },
+	{12.5, { 3, 4, 6, 7, 8, 8, 9, 10, 10, 11, 12, 13, 13, 14, 15} },
+	{  13, { 2, 4, 5, 6, 7, 7, 9, 10, 10, 11, 12, 12, 13, 13, 14} },
+	{13.5, { 2, 4, 5, 5, 6, 7, 9, 9, 10, 10, 12, 12, 12, 13, 14} },
+	{  14, { 2, 3, 4, 5, 6, 7, 8, 8, 9, 9, 11, 12, 12, 12, 13} },
+	{14.5, { 2, 3, 3, 5, 6, 6, 8, 8, 8, 9, 11, 11, 11, 12, 13} },
+	{  15, { 2, 3, 3, 5, 5, 6, 7, 8, 8, 8, 10, 11, 11, 11, 13} },
+	{15.5, { 2, 2, 3, 4, 5, 6, 7, 7, 8, 8, 10, 10, 10, 11, 12} },
+	{  16, { 2, 2, 3, 4, 5, 6, 7, 7, 8, 8, 10, 10, 10, 10, 12} },
+	{16.5, { 1, 2, 2, 4, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 11} },
+	{  17, { 1, 1, 2, 3, 4, 4, 6, 6, 6, 7, 8, 8, 8, 9, 11} },
+	{17.5, { 1, 1, 2, 3, 4, 4, 5, 6, 6, 6, 7, 8, 8, 9, 10} },
+	{  18, { 1, 1, 1, 2, 3, 3, 5, 5, 5, 6, 7, 7, 8, 8, 10} },
+	{18.5, { 1, 1, 1, 2, 3, 3, 5, 5, 5, 5, 7, 7, 7, 8, 10} },
+	{  19, { 1, 1, 1, 2, 3, 3, 4, 5, 5, 5, 6, 6, 7, 7, 9} },
+	{19.5, { 1, 1, 1, 2, 2, 2, 4, 5, 5, 5, 6, 6, 6, 7, 9} },
+	{  20, { 1, 1, 1, 2, 2, 2, 4, 5, 5, 5, 6, 6, 6, 6, 8} },
+	{20.5, { 0, 0, 0, 1, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6, 8} },
+	{  21, { 0, 0, 0, 1, 1, 2, 3, 3, 4, 4, 4, 5, 5, 5, 7} },
+	{21.5, { 0, 0, 0, 0, 1, 1, 2, 3, 3, 3, 4, 4, 4, 5, 7} },
+	{  22, { 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 5, 7} },
+	{22.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4, 6} },
+	{  23, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 3, 3, 4, 6} },
+	{23.5, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 2, 2, 3, 5} },
+	{  24, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 2, 2, 3, 5} }
+};
+
+
+const qp_table   qp_table_444_12bpc_max = {
+	{   6, {12, 14, 16, 16, 17, 17, 17, 18, 19, 20, 20, 20, 20, 21, 23} },
+	{ 6.5, {12, 14, 15, 16, 16, 16, 17, 18, 19, 19, 20, 20, 20, 21, 23} },
+	{   7, {12, 13, 15, 15, 16, 16, 16, 17, 18, 19, 19, 20, 20, 21, 22} },
+	{ 7.5, {12, 13, 14, 15, 15, 16, 16, 17, 18, 18, 19, 19, 20, 21, 22} },
+	{   8, {12, 12, 13, 14, 15, 15, 15, 16, 17, 18, 18, 19, 19, 20, 21} },
+	{ 8.5, {12, 12, 13, 14, 15, 15, 15, 16, 17, 18, 18, 19, 19, 20, 21} },
+	{   9, {11, 12, 13, 14, 15, 15, 15, 16, 17, 17, 18, 18, 19, 19, 21} },
+	{ 9.5, {11, 12, 13, 14, 15, 15, 15, 16, 17, 17, 18, 18, 19, 19, 21} },
+	{  10, {11, 12, 13, 14, 15, 15, 15, 16, 17, 17, 18, 18, 19, 19, 20} },
+	{10.5, {10, 12, 13, 14, 15, 15, 15, 16, 17, 17, 18, 18, 18, 19, 20} },
+	{  11, { 9, 11, 13, 14, 15, 15, 15, 16, 16, 17, 17, 17, 18, 18, 19} },
+	{11.5, { 9, 11, 13, 14, 15, 15, 15, 16, 16, 17, 17, 17, 17, 18, 19} },
+	{  12, { 6, 9, 12, 13, 14, 14, 15, 16, 16, 17, 17, 17, 17, 18, 19} },
+	{12.5, { 6, 9, 12, 13, 14, 14, 14, 15, 15, 16, 16, 17, 17, 18, 19} },
+	{  13, { 5, 9, 12, 13, 13, 14, 14, 15, 15, 16, 16, 16, 16, 17, 18} },
+	{13.5, { 5, 8, 11, 12, 12, 13, 13, 14, 14, 15, 15, 16, 16, 17, 18} },
+	{  14, { 5, 8, 10, 11, 12, 12, 12, 13, 14, 14, 15, 16, 16, 16, 18} },
+	{14.5, { 4, 7, 10, 11, 11, 12, 12, 13, 13, 14, 14, 15, 15, 16, 17} },
+	{  15, { 4, 7, 9, 10, 10, 11, 11, 12, 13, 13, 14, 15, 15, 16, 17} },
+	{15.5, { 4, 7, 9, 10, 10, 11, 11, 12, 13, 13, 14, 15, 15, 16, 17} },
+	{  16, { 4, 7, 9, 10, 10, 11, 11, 12, 13, 13, 13, 14, 14, 15, 16} },
+	{16.5, { 4, 5, 7, 8, 10, 11, 11, 12, 13, 13, 13, 14, 14, 15, 16} },
+	{  17, { 4, 5, 7, 8, 8, 9, 11, 11, 12, 12, 12, 13, 13, 14, 16} },
+	{17.5, { 3, 5, 7, 8, 8, 9, 10, 11, 12, 12, 12, 13, 13, 14, 16} },
+	{  18, { 3, 5, 7, 8, 8, 9, 10, 11, 12, 12, 12, 13, 13, 14, 15} },
+	{18.5, { 3, 5, 7, 8, 8, 9, 10, 11, 12, 12, 12, 13, 13, 14, 15} },
+	{  19, { 3, 4, 6, 7, 8, 8, 9, 10, 11, 11, 11, 12, 12, 13, 14} },
+	{19.5, { 3, 4, 6, 7, 8, 8, 9, 10, 11, 11, 11, 12, 12, 13, 14} },
+	{  20, { 2, 4, 5, 6, 7, 8, 9, 10, 10, 10, 10, 11, 11, 12, 14} },
+	{20.5, { 2, 3, 5, 5, 7, 8, 8, 8, 9, 10, 10, 11, 11, 12, 14} },
+	{  21, { 2, 3, 5, 5, 7, 7, 7, 8, 8, 9, 10, 11, 11, 12, 14} },
+	{21.5, { 2, 3, 5, 5, 6, 6, 7, 8, 8, 9, 10, 11, 11, 12, 13} },
+	{  22, { 2, 2, 4, 5, 6, 6, 7, 7, 8, 9, 10, 10, 10, 11, 13} },
+	{22.5, { 2, 2, 4, 5, 5, 6, 7, 7, 8, 9, 10, 10, 10, 11, 12} },
+	{  23, { 2, 2, 4, 5, 5, 6, 7, 7, 7, 8, 10, 10, 10, 10, 12} },
+	{23.5, { 2, 2, 3, 5, 5, 6, 7, 7, 7, 8, 10, 10, 10, 10, 12} },
+	{  24, { 2, 2, 3, 4, 4, 5, 7, 7, 7, 8, 9, 9, 9, 10, 12} },
+	{24.5, { 1, 2, 3, 4, 4, 5, 6, 7, 7, 8, 9, 9, 9, 10, 12} },
+	{  25, { 1, 2, 3, 3, 4, 5, 6, 6, 7, 8, 9, 9, 9, 9, 11} },
+	{25.5, { 1, 1, 3, 3, 4, 5, 6, 6, 7, 7, 8, 9, 9, 9, 11} },
+	{  26, { 1, 1, 3, 3, 3, 4, 5, 6, 6, 7, 8, 8, 8, 8, 10} },
+	{26.5, { 1, 1, 2, 3, 3, 4, 5, 6, 6, 6, 8, 8, 8, 8, 10} },
+	{  27, { 1, 1, 2, 3, 3, 4, 5, 5, 6, 6, 7, 8, 8, 8, 10} },
+	{27.5, { 1, 1, 2, 2, 3, 3, 5, 5, 5, 6, 7, 8, 8, 8, 10} },
+	{  28, { 0, 1, 1, 2, 2, 3, 4, 5, 5, 5, 7, 7, 7, 8, 10} },
+	{28.5, { 0, 1, 1, 2, 2, 3, 4, 4, 5, 5, 6, 7, 7, 7, 9} },
+	{  29, { 0, 1, 1, 2, 2, 3, 4, 4, 5, 5, 6, 6, 7, 7, 9} },
+	{29.5, { 0, 1, 1, 2, 2, 2, 3, 3, 4, 5, 6, 6, 7, 7, 8} },
+	{  30, { 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 6, 6, 6, 6, 8} },
+	{30.5, { 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 5, 6, 8} },
+	{  31, { 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 5, 6, 8} },
+	{31.5, { 0, 0, 0, 0, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 8} },
+	{  32, { 0, 0, 0, 0, 1, 2, 2, 3, 3, 4, 4, 4, 4, 5, 7} },
+	{32.5, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 4, 4, 4, 5, 7} },
+	{  33, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 6} },
+	{33.5, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 6} },
+	{  34, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 3, 4, 6} },
+	{34.5, { 0, 0, 0, 0, 1, 1, 1, 1, 2, 3, 3, 3, 3, 4, 6} },
+	{  35, { 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 3, 5} },
+	{35.5, { 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 3, 5} },
+	{  36, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 4} }
+};
+
+
+const qp_table   qp_table_420_8bpc_min = {
+	{   4, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 9, 13} },
+	{ 4.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 8, 12} },
+	{   5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 8, 12} },
+	{ 5.5, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 11} },
+	{   6, { 0, 0, 1, 1, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 10} },
+	{ 6.5, { 0, 0, 1, 1, 2, 2, 3, 3, 3, 3, 4, 5, 5, 7, 10} },
+	{   7, { 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 4, 5, 5, 7, 9} },
+	{ 7.5, { 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{   8, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{ 8.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 6, 7} },
+	{   9, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6} },
+	{ 9.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 6} },
+	{  10, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 4, 5} },
+	{10.5, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 3, 5} },
+	{  11, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 4} },
+	{11.5, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 3, 4} },
+	{  12, { 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 3} }
+};
+
+
+const qp_table   qp_table_422_8bpc_min = {
+	{   6, { 0, 0, 1, 2, 3, 3, 3, 3, 3, 3, 5, 5, 5, 8, 12} },
+	{ 6.5, { 0, 0, 1, 2, 3, 3, 3, 3, 3, 3, 5, 5, 5, 8, 12} },
+	{   7, { 0, 0, 1, 2, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 11} },
+	{ 7.5, { 0, 0, 1, 2, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 11} },
+	{   8, { 0, 0, 1, 2, 3, 3, 3, 3, 3, 3, 5, 5, 5, 7, 10} },
+	{ 8.5, { 0, 0, 1, 2, 2, 2, 2, 3, 3, 3, 4, 5, 5, 7, 10} },
+	{   9, { 0, 0, 0, 1, 2, 2, 2, 2, 2, 3, 4, 5, 5, 7, 9} },
+	{ 9.5, { 0, 0, 0, 1, 1, 1, 1, 2, 2, 3, 4, 4, 5, 7, 9} },
+	{  10, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{10.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 7, 8} },
+	{  11, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 6, 7} },
+	{11.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 6, 7} },
+	{  12, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 4, 4, 5, 5, 6} },
+	{12.5, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 5, 6} },
+	{  13, { 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 4, 4, 5} },
+	{13.5, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 4, 5} },
+	{  14, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4} },
+	{14.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 4} },
+	{  15, { 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 4} },
+	{15.5, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 3} },
+	{  16, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 3} }
+};
+
+
+const qp_table   qp_table_422_10bpc_max = {
+	{   6, { 8, 8, 9, 10, 11, 11, 11, 12, 13, 14, 14, 15, 15, 16, 17} },
+	{ 6.5, { 8, 8, 9, 10, 11, 11, 11, 12, 13, 14, 14, 15, 15, 16, 17} },
+	{   7, { 7, 8, 9, 10, 11, 11, 11, 12, 13, 13, 14, 14, 15, 15, 16} },
+	{ 7.5, { 5, 6, 8, 10, 11, 11, 11, 12, 12, 13, 13, 14, 14, 15, 16} },
+	{   8, { 4, 6, 7, 9, 10, 11, 11, 12, 12, 13, 13, 13, 13, 14, 15} },
+	{ 8.5, { 4, 5, 6, 8, 9, 10, 10, 11, 11, 12, 12, 13, 13, 14, 15} },
+	{   9, { 3, 4, 5, 7, 8, 9, 9, 10, 10, 11, 11, 12, 12, 13, 14} },
+	{ 9.5, { 3, 4, 4, 6, 6, 8, 8, 9, 10, 10, 11, 11, 12, 13, 14} },
+	{  10, { 2, 3, 3, 5, 5, 7, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{10.5, { 2, 3, 3, 5, 5, 6, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{  11, { 2, 3, 3, 5, 5, 6, 7, 8, 9, 9, 10, 10, 11, 11, 12} },
+	{11.5, { 2, 3, 3, 5, 5, 5, 7, 7, 8, 9, 9, 10, 10, 11, 12} },
+	{  12, { 2, 3, 3, 5, 5, 5, 7, 7, 8, 8, 9, 9, 10, 10, 11} },
+	{12.5, { 2, 2, 3, 4, 5, 5, 6, 7, 7, 8, 8, 9, 9, 10, 11} },
+	{  13, { 1, 2, 3, 4, 5, 5, 6, 7, 7, 8, 8, 8, 9, 9, 10} },
+	{13.5, { 1, 2, 3, 3, 4, 5, 6, 6, 7, 7, 8, 8, 8, 9, 10} },
+	{  14, { 1, 2, 3, 3, 4, 5, 5, 5, 6, 6, 7, 8, 8, 8, 9} },
+	{14.5, { 1, 2, 2, 3, 4, 4, 5, 5, 5, 6, 7, 7, 7, 8, 9} },
+	{  15, { 1, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6, 7, 7, 7, 9} },
+	{15.5, { 1, 1, 2, 2, 3, 4, 4, 4, 5, 5, 6, 6, 6, 7, 8} },
+	{  16, { 1, 1, 2, 2, 3, 4, 4, 4, 5, 5, 6, 6, 6, 6, 8} },
+	{16.5, { 0, 1, 1, 2, 2, 3, 3, 4, 4, 4, 4, 5, 5, 6, 7} },
+	{  17, { 0, 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 4, 5, 7} },
+	{17.5, { 0, 0, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 4, 5, 6} },
+	{  18, { 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 6} },
+	{18.5, { 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 6} },
+	{  19, { 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 3, 3, 5} },
+	{19.5, { 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 3, 5} },
+	{  20, { 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2, 4} }
+};
+
+
+const qp_table qp_table_420_10bpc_max = {
+	{   4, { 8, 8, 9, 10, 11, 11, 11, 12, 13, 14, 14, 15, 15, 17, 18} },
+	{ 4.5, { 8, 8, 9, 10, 11, 11, 11, 12, 13, 14, 14, 15, 15, 16, 17} },
+	{   5, { 7, 8, 9, 10, 11, 11, 11, 12, 13, 13, 14, 14, 15, 16, 17} },
+	{ 5.5, { 6, 7, 8, 9, 10, 10, 11, 12, 12, 13, 13, 14, 14, 15, 16} },
+	{   6, { 4, 6, 8, 9, 10, 10, 11, 12, 12, 13, 13, 13, 13, 14, 15} },
+	{ 6.5, { 4, 5, 7, 8, 8, 9, 10, 11, 11, 12, 12, 13, 13, 14, 15} },
+	{   7, { 3, 4, 6, 7, 7, 8, 9, 10, 10, 11, 12, 12, 13, 13, 14} },
+	{ 7.5, { 3, 4, 5, 6, 6, 7, 8, 9, 10, 10, 11, 11, 12, 12, 13} },
+	{   8, { 2, 3, 4, 5, 5, 6, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{ 8.5, { 1, 3, 3, 4, 4, 6, 7, 8, 9, 9, 10, 10, 11, 11, 12} },
+	{   9, { 1, 3, 3, 4, 4, 6, 7, 8, 8, 9, 9, 10, 10, 10, 11} },
+	{ 9.5, { 1, 3, 3, 3, 4, 5, 6, 7, 8, 8, 9, 9, 9, 10, 11} },
+	{  10, { 1, 2, 3, 3, 4, 4, 5, 6, 7, 8, 8, 9, 9, 9, 11} },
+	{10.5, { 1, 1, 3, 3, 3, 4, 5, 5, 7, 7, 8, 8, 8, 8, 10} },
+	{  11, { 0, 1, 2, 3, 3, 3, 4, 5, 6, 7, 7, 7, 8, 8, 9} },
+	{11.5, { 0, 1, 1, 2, 3, 3, 3, 4, 5, 6, 6, 7, 7, 7, 9} },
+	{  12, { 0, 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 6, 6, 8} },
+	{12.5, { 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 5, 6, 7} },
+	{  13, { 0, 0, 0, 1, 2, 2, 3, 3, 3, 4, 4, 5, 5, 5, 7} },
+	{13.5, { 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 4, 6} },
+	{  14, { 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 4, 6} },
+	{14.5, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 2, 3, 3, 3, 3, 5} },
+	{  15, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 2, 3, 5} }
+};
+
+
+const qp_table   qp_table_420_10bpc_min = {
+	{   4, { 0, 4, 4, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 13, 17} },
+	{ 4.5, { 0, 4, 4, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 12, 16} },
+	{   5, { 0, 4, 4, 5, 7, 7, 7, 7, 7, 7, 9, 9, 9, 12, 16} },
+	{ 5.5, { 0, 3, 3, 4, 6, 7, 7, 7, 7, 7, 9, 9, 9, 11, 15} },
+	{   6, { 0, 2, 3, 4, 6, 7, 7, 7, 7, 7, 9, 9, 9, 11, 14} },
+	{ 6.5, { 0, 2, 3, 4, 5, 6, 6, 7, 7, 7, 8, 9, 9, 11, 14} },
+	{   7, { 0, 2, 3, 4, 5, 5, 6, 6, 7, 7, 8, 8, 9, 11, 13} },
+	{ 7.5, { 0, 2, 3, 4, 4, 5, 5, 6, 7, 7, 8, 8, 9, 11, 12} },
+	{   8, { 0, 2, 3, 4, 4, 5, 5, 6, 6, 7, 8, 8, 9, 11, 12} },
+	{ 8.5, { 0, 2, 2, 3, 3, 5, 5, 6, 6, 7, 8, 8, 9, 10, 11} },
+	{   9, { 0, 2, 2, 3, 3, 5, 5, 6, 6, 7, 7, 8, 9, 9, 10} },
+	{ 9.5, { 0, 2, 2, 2, 3, 4, 4, 5, 6, 6, 7, 8, 8, 9, 10} },
+	{  10, { 0, 1, 2, 2, 3, 3, 4, 4, 5, 6, 6, 8, 8, 8, 10} },
+	{10.5, { 0, 0, 2, 2, 2, 3, 4, 4, 5, 5, 6, 7, 7, 7, 9} },
+	{  11, { 0, 0, 1, 2, 2, 2, 3, 4, 4, 5, 5, 6, 7, 7, 8} },
+	{11.5, { 0, 0, 0, 1, 2, 2, 2, 3, 4, 4, 5, 6, 6, 6, 8} },
+	{  12, { 0, 0, 0, 0, 1, 1, 2, 2, 3, 4, 4, 5, 5, 5, 7} },
+	{12.5, { 0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 4, 5, 6} },
+	{  13, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 6} },
+	{13.5, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 3, 5} },
+	{  14, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 5} },
+	{14.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 4} },
+	{  15, { 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2, 4} }
+};
+
+
+const qp_table   qp_table_444_10bpc_max = {
+	{   6, { 8, 10, 12, 12, 13, 13, 13, 14, 15, 16, 16, 16, 16, 17, 19} },
+	{ 6.5, { 8, 10, 11, 12, 12, 12, 13, 14, 15, 15, 16, 16, 16, 17, 19} },
+	{   7, { 8, 9, 11, 11, 12, 12, 12, 13, 14, 15, 15, 16, 16, 17, 18} },
+	{ 7.5, { 8, 9, 10, 11, 11, 12, 12, 13, 14, 14, 15, 15, 16, 17, 18} },
+	{   8, { 8, 8, 9, 10, 11, 11, 11, 12, 13, 14, 14, 15, 15, 16, 17} },
+	{ 8.5, { 8, 8, 9, 10, 11, 11, 11, 12, 13, 14, 14, 15, 15, 16, 17} },
+	{   9, { 7, 8, 9, 10, 11, 11, 11, 12, 13, 13, 14, 14, 15, 15, 17} },
+	{ 9.5, { 7, 8, 9, 10, 11, 11, 11, 12, 13, 13, 14, 14, 15, 15, 17} },
+	{  10, { 7, 8, 9, 10, 11, 11, 11, 12, 13, 13, 14, 14, 15, 15, 16} },
+	{10.5, { 6, 8, 9, 10, 11, 11, 11, 12, 13, 13, 14, 14, 14, 15, 16} },
+	{  11, { 5, 7, 9, 10, 11, 11, 11, 12, 12, 13, 13, 13, 14, 14, 15} },
+	{11.5, { 5, 7, 9, 10, 11, 11, 11, 12, 12, 13, 13, 13, 13, 14, 15} },
+	{  12, { 4, 6, 8, 9, 10, 10, 11, 12, 12, 13, 13, 13, 13, 14, 15} },
+	{12.5, { 4, 6, 8, 9, 10, 10, 10, 11, 11, 12, 12, 13, 13, 14, 15} },
+	{  13, { 3, 6, 8, 9, 9, 10, 10, 11, 11, 12, 12, 12, 12, 13, 14} },
+	{13.5, { 3, 5, 7, 8, 8, 9, 9, 10, 10, 11, 11, 12, 12, 13, 14} },
+	{  14, { 3, 5, 6, 7, 8, 8, 8, 9, 10, 10, 11, 12, 12, 12, 14} },
+	{14.5, { 2, 4, 6, 7, 7, 8, 8, 9, 9, 10, 10, 11, 11, 12, 13} },
+	{  15, { 2, 4, 5, 6, 6, 7, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{15.5, { 2, 4, 5, 6, 6, 7, 7, 8, 9, 9, 10, 11, 11, 12, 13} },
+	{  16, { 2, 4, 5, 6, 6, 7, 7, 8, 9, 9, 9, 10, 10, 11, 12} },
+	{16.5, { 2, 3, 4, 5, 6, 7, 7, 8, 9, 9, 9, 10, 10, 11, 12} },
+	{  17, { 2, 3, 4, 5, 5, 6, 7, 7, 8, 8, 8, 9, 9, 10, 12} },
+	{17.5, { 1, 3, 4, 5, 5, 6, 6, 7, 8, 8, 8, 9, 9, 10, 12} },
+	{  18, { 1, 3, 4, 5, 5, 6, 6, 7, 8, 8, 8, 9, 9, 10, 11} },
+	{18.5, { 1, 3, 4, 5, 5, 6, 6, 7, 8, 8, 8, 9, 9, 10, 11} },
+	{  19, { 1, 2, 3, 4, 5, 5, 5, 6, 7, 7, 7, 8, 8, 9, 10} },
+	{19.5, { 1, 2, 3, 4, 5, 5, 5, 6, 7, 7, 7, 8, 8, 9, 10} },
+	{  20, { 1, 2, 3, 3, 4, 5, 5, 6, 6, 6, 6, 7, 7, 8, 10} },
+	{20.5, { 1, 2, 3, 3, 4, 5, 5, 5, 5, 6, 6, 7, 7, 8, 10} },
+	{  21, { 1, 2, 3, 3, 4, 4, 4, 5, 5, 5, 6, 7, 7, 8, 10} },
+	{21.5, { 1, 2, 3, 3, 3, 3, 4, 5, 5, 5, 6, 7, 7, 8, 9} },
+	{  22, { 1, 1, 2, 3, 3, 3, 4, 4, 5, 5, 6, 6, 6, 7, 9} },
+	{22.5, { 1, 1, 2, 3, 3, 3, 4, 4, 5, 5, 6, 6, 6, 7, 8} },
+	{  23, { 1, 1, 2, 3, 3, 3, 4, 4, 4, 4, 6, 6, 6, 6, 8} },
+	{23.5, { 1, 1, 1, 3, 3, 3, 4, 4, 4, 4, 6, 6, 6, 6, 8} },
+	{  24, { 1, 1, 1, 2, 2, 3, 4, 4, 4, 4, 5, 5, 5, 6, 8} },
+	{24.5, { 0, 1, 1, 2, 2, 3, 3, 4, 4, 4, 5, 5, 5, 6, 8} },
+	{  25, { 0, 1, 1, 1, 2, 3, 3, 3, 4, 4, 5, 5, 5, 5, 7} },
+	{25.5, { 0, 0, 1, 1, 2, 3, 3, 3, 4, 4, 4, 5, 5, 5, 7} },
+	{  26, { 0, 0, 1, 1, 1, 2, 2, 3, 3, 4, 4, 4, 4, 4, 6} },
+	{26.5, { 0, 0, 0, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 4, 6} },
+	{  27, { 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 4, 6} },
+	{27.5, { 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 6} },
+	{  28, { 0, 0, 0, 0, 0, 1, 1, 2, 2, 2, 3, 3, 3, 3, 5} },
+	{28.5, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 5} },
+	{  29, { 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 2, 3, 3, 4} },
+	{29.5, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 4} },
+	{  30, { 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 4} }
+};
+
+
+const qp_table   qp_table_422_8bpc_max = {
+	{   6, { 4, 4, 5, 6, 7, 7, 7, 8, 9, 10, 10, 11, 11, 12, 13} },
+	{ 6.5, { 4, 4, 5, 6, 7, 7, 7, 8, 9, 10, 10, 11, 11, 12, 13} },
+	{   7, { 3, 4, 5, 6, 7, 7, 7, 8, 9, 9, 10, 10, 11, 11, 12} },
+	{ 7.5, { 3, 4, 5, 6, 7, 7, 7, 8, 8, 9, 9, 10, 10, 11, 12} },
+	{   8, { 2, 4, 5, 6, 7, 7, 7, 8, 8, 9, 9, 9, 9, 10, 11} },
+	{ 8.5, { 2, 3, 4, 5, 6, 6, 6, 7, 7, 8, 8, 9, 9, 10, 11} },
+	{   9, { 1, 2, 3, 4, 5, 5, 5, 6, 6, 7, 7, 8, 8, 9, 10} },
+	{ 9.5, { 1, 2, 2, 3, 3, 4, 4, 5, 6, 6, 7, 7, 8, 9, 10} },
+	{  10, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 7, 7, 8, 9} },
+	{10.5, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 7, 7, 8, 9} },
+	{  11, { 0, 1, 1, 2, 2, 3, 3, 4, 5, 5, 6, 6, 7, 7, 8} },
+	{11.5, { 0, 1, 1, 2, 2, 2, 3, 3, 4, 5, 5, 6, 6, 7, 8} },
+	{  12, { 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6, 7} },
+	{12.5, { 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 5, 5, 6, 7} },
+	{  13, { 0, 0, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 5, 5, 6} },
+	{13.5, { 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, 5, 6} },
+	{  14, { 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 4, 5} },
+	{14.5, { 0, 0, 0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 5} },
+	{  15, { 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 5} },
+	{15.5, { 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 3, 4} },
+	{  16, { 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2, 2, 3, 4} }
+};
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dsc/rc_calc_fpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dsc/rc_calc_fpu.c
@@ -0,0 +1,291 @@
+/*
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#include "rc_calc_fpu.h"
+
+#include "qp_tables.h"
+#include "amdgpu_dm/dc_fpu.h"
+
+#define table_hash(mode, bpc, max_min) ((mode << 16) | (bpc << 8) | max_min)
+
+#define MODE_SELECT(val444, val422, val420) \
+	(cm == CM_444 || cm == CM_RGB) ? (val444) : (cm == CM_422 ? (val422) : (val420))
+
+
+#define TABLE_CASE(mode, bpc, max)   case (table_hash(mode, BPC_##bpc, max)): \
+	table = qp_table_##mode##_##bpc##bpc_##max; \
+	table_size = sizeof(qp_table_##mode##_##bpc##bpc_##max)/sizeof(*qp_table_##mode##_##bpc##bpc_##max); \
+	break
+
+static int median3(int a, int b, int c)
+{
+	if (a > b)
+		swap(a, b);
+	if (b > c)
+		swap(b, c);
+	if (a > b)
+		swap(b, c);
+
+	return b;
+}
+
+static double dsc_roundf(double num)
+{
+	if (num < 0.0)
+		num = num - 0.5;
+	else
+		num = num + 0.5;
+
+	return (int)(num);
+}
+
+static double dsc_ceil(double num)
+{
+	double retval = (int)num;
+
+	if (retval != num && num > 0)
+		retval = num + 1;
+
+	return (int)retval;
+}
+
+static void get_qp_set(qp_set qps, enum colour_mode cm, enum bits_per_comp bpc,
+		       enum max_min max_min, float bpp)
+{
+	int mode = MODE_SELECT(444, 422, 420);
+	int sel = table_hash(mode, bpc, max_min);
+	int table_size = 0;
+	int index;
+	const struct qp_entry *table = 0L;
+
+	// alias enum
+	enum { min = DAL_MM_MIN, max = DAL_MM_MAX };
+	switch (sel) {
+		TABLE_CASE(444,  8, max);
+		TABLE_CASE(444,  8, min);
+		TABLE_CASE(444, 10, max);
+		TABLE_CASE(444, 10, min);
+		TABLE_CASE(444, 12, max);
+		TABLE_CASE(444, 12, min);
+		TABLE_CASE(422,  8, max);
+		TABLE_CASE(422,  8, min);
+		TABLE_CASE(422, 10, max);
+		TABLE_CASE(422, 10, min);
+		TABLE_CASE(422, 12, max);
+		TABLE_CASE(422, 12, min);
+		TABLE_CASE(420,  8, max);
+		TABLE_CASE(420,  8, min);
+		TABLE_CASE(420, 10, max);
+		TABLE_CASE(420, 10, min);
+		TABLE_CASE(420, 12, max);
+		TABLE_CASE(420, 12, min);
+	}
+
+	if (table == 0)
+		return;
+
+	index = (bpp - table[0].bpp) * 2;
+
+	/* requested size is bigger than the table */
+	if (index >= table_size) {
+		dm_error("ERROR: Requested rc_calc to find a bpp entry that exceeds the table size\n");
+		return;
+	}
+
+	memcpy(qps, table[index].qps, sizeof(qp_set));
+}
+
+static void get_ofs_set(qp_set ofs, enum colour_mode mode, float bpp)
+{
+	int   *p = ofs;
+
+	if (mode == CM_444 || mode == CM_RGB) {
+		*p++ = (bpp <=  6) ? (0) : ((((bpp >=  8) && (bpp <= 12))) ? (2) : ((bpp >= 15) ? (10) : ((((bpp > 6) && (bpp < 8))) ? (0 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (2 + dsc_roundf((bpp - 12) * (8 / 3.0))))));
+		*p++ = (bpp <=  6) ? (-2) : ((((bpp >=  8) && (bpp <= 12))) ? (0) : ((bpp >= 15) ? (8) : ((((bpp > 6) && (bpp < 8))) ? (-2 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (0 + dsc_roundf((bpp - 12) * (8 / 3.0))))));
+		*p++ = (bpp <=  6) ? (-2) : ((((bpp >=  8) && (bpp <= 12))) ? (0) : ((bpp >= 15) ? (6) : ((((bpp > 6) && (bpp < 8))) ? (-2 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (0 + dsc_roundf((bpp - 12) * (6 / 3.0))))));
+		*p++ = (bpp <=  6) ? (-4) : ((((bpp >=  8) && (bpp <= 12))) ? (-2) : ((bpp >= 15) ? (4) : ((((bpp > 6) && (bpp < 8))) ? (-4 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (-2 + dsc_roundf((bpp - 12) * (6 / 3.0))))));
+		*p++ = (bpp <=  6) ? (-6) : ((((bpp >=  8) && (bpp <= 12))) ? (-4) : ((bpp >= 15) ? (2) : ((((bpp > 6) && (bpp < 8))) ? (-6 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (-4 + dsc_roundf((bpp - 12) * (6 / 3.0))))));
+		*p++ = (bpp <= 12) ? (-6) : ((bpp >= 15) ? (0) : (-6 + dsc_roundf((bpp - 12) * (6 / 3.0))));
+		*p++ = (bpp <= 12) ? (-8) : ((bpp >= 15) ? (-2) : (-8 + dsc_roundf((bpp - 12) * (6 / 3.0))));
+		*p++ = (bpp <= 12) ? (-8) : ((bpp >= 15) ? (-4) : (-8 + dsc_roundf((bpp - 12) * (4 / 3.0))));
+		*p++ = (bpp <= 12) ? (-8) : ((bpp >= 15) ? (-6) : (-8 + dsc_roundf((bpp - 12) * (2 / 3.0))));
+		*p++ = (bpp <= 12) ? (-10) : ((bpp >= 15) ? (-8) : (-10 + dsc_roundf((bpp - 12) * (2 / 3.0))));
+		*p++ = -10;
+		*p++ = (bpp <=  6) ? (-12) : ((bpp >=  8) ? (-10) : (-12 + dsc_roundf((bpp -  6) * (2 / 2.0))));
+		*p++ = -12;
+		*p++ = -12;
+		*p++ = -12;
+	} else if (mode == CM_422) {
+		*p++ = (bpp <=  8) ? (2) : ((bpp >= 10) ? (10) : (2 + dsc_roundf((bpp -  8) * (8 / 2.0))));
+		*p++ = (bpp <=  8) ? (0) : ((bpp >= 10) ? (8) : (0 + dsc_roundf((bpp -  8) * (8 / 2.0))));
+		*p++ = (bpp <=  8) ? (0) : ((bpp >= 10) ? (6) : (0 + dsc_roundf((bpp -  8) * (6 / 2.0))));
+		*p++ = (bpp <=  8) ? (-2) : ((bpp >= 10) ? (4) : (-2 + dsc_roundf((bpp -  8) * (6 / 2.0))));
+		*p++ = (bpp <=  8) ? (-4) : ((bpp >= 10) ? (2) : (-4 + dsc_roundf((bpp -  8) * (6 / 2.0))));
+		*p++ = (bpp <=  8) ? (-6) : ((bpp >= 10) ? (0) : (-6 + dsc_roundf((bpp -  8) * (6 / 2.0))));
+		*p++ = (bpp <=  8) ? (-8) : ((bpp >= 10) ? (-2) : (-8 + dsc_roundf((bpp -  8) * (6 / 2.0))));
+		*p++ = (bpp <=  8) ? (-8) : ((bpp >= 10) ? (-4) : (-8 + dsc_roundf((bpp -  8) * (4 / 2.0))));
+		*p++ = (bpp <=  8) ? (-8) : ((bpp >= 10) ? (-6) : (-8 + dsc_roundf((bpp -  8) * (2 / 2.0))));
+		*p++ = (bpp <=  8) ? (-10) : ((bpp >= 10) ? (-8) : (-10 + dsc_roundf((bpp -  8) * (2 / 2.0))));
+		*p++ = -10;
+		*p++ = (bpp <=  6) ? (-12) : ((bpp >= 7) ? (-10) : (-12 + dsc_roundf((bpp -  6) * (2.0 / 1))));
+		*p++ = -12;
+		*p++ = -12;
+		*p++ = -12;
+	} else {
+		*p++ = (bpp <=  6) ? (2) : ((bpp >=  8) ? (10) : (2 + dsc_roundf((bpp -  6) * (8 / 2.0))));
+		*p++ = (bpp <=  6) ? (0) : ((bpp >=  8) ? (8) : (0 + dsc_roundf((bpp -  6) * (8 / 2.0))));
+		*p++ = (bpp <=  6) ? (0) : ((bpp >=  8) ? (6) : (0 + dsc_roundf((bpp -  6) * (6 / 2.0))));
+		*p++ = (bpp <=  6) ? (-2) : ((bpp >=  8) ? (4) : (-2 + dsc_roundf((bpp -  6) * (6 / 2.0))));
+		*p++ = (bpp <=  6) ? (-4) : ((bpp >=  8) ? (2) : (-4 + dsc_roundf((bpp -  6) * (6 / 2.0))));
+		*p++ = (bpp <=  6) ? (-6) : ((bpp >=  8) ? (0) : (-6 + dsc_roundf((bpp -  6) * (6 / 2.0))));
+		*p++ = (bpp <=  6) ? (-8) : ((bpp >=  8) ? (-2) : (-8 + dsc_roundf((bpp -  6) * (6 / 2.0))));
+		*p++ = (bpp <=  6) ? (-8) : ((bpp >=  8) ? (-4) : (-8 + dsc_roundf((bpp -  6) * (4 / 2.0))));
+		*p++ = (bpp <=  6) ? (-8) : ((bpp >=  8) ? (-6) : (-8 + dsc_roundf((bpp -  6) * (2 / 2.0))));
+		*p++ = (bpp <=  6) ? (-10) : ((bpp >=  8) ? (-8) : (-10 + dsc_roundf((bpp -  6) * (2 / 2.0))));
+		*p++ = -10;
+		*p++ = (bpp <=  4) ? (-12) : ((bpp >=  5) ? (-10) : (-12 + dsc_roundf((bpp -  4) * (2 / 1.0))));
+		*p++ = -12;
+		*p++ = -12;
+		*p++ = -12;
+	}
+}
+
+void _do_calc_rc_params(struct rc_params *rc,
+		enum colour_mode cm,
+		enum bits_per_comp bpc,
+		u16 drm_bpp,
+		bool is_navite_422_or_420,
+		int slice_width,
+		int slice_height,
+		int minor_version)
+{
+	float bpp;
+	float bpp_group;
+	float initial_xmit_delay_factor;
+	int padding_pixels;
+	int i;
+
+	dc_assert_fp_enabled();
+
+	bpp = ((float)drm_bpp / 16.0);
+	/* in native_422 or native_420 modes, the bits_per_pixel is double the
+	 * target bpp (the latter is what calc_rc_params expects)
+	 */
+	if (is_navite_422_or_420)
+		bpp /= 2.0;
+
+	rc->rc_quant_incr_limit0 = ((bpc == BPC_8) ? 11 : (bpc == BPC_10 ? 15 : 19)) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
+	rc->rc_quant_incr_limit1 = ((bpc == BPC_8) ? 11 : (bpc == BPC_10 ? 15 : 19)) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
+
+	bpp_group = MODE_SELECT(bpp, bpp * 2.0, bpp * 2.0);
+
+	switch (cm) {
+	case CM_420:
+		rc->initial_fullness_offset = (bpp >=  6) ? (2048) : ((bpp <=  4) ? (6144) : ((((bpp >  4) && (bpp <=  5))) ? (6144 - dsc_roundf((bpp - 4) * (512))) : (5632 - dsc_roundf((bpp -  5) * (3584)))));
+		rc->first_line_bpg_offset   = median3(0, (12 + (int) (0.09 *  min(34, slice_height - 8))), (int)((3 * bpc * 3) - (3 * bpp_group)));
+		rc->second_line_bpg_offset  = median3(0, 12, (int)((3 * bpc * 3) - (3 * bpp_group)));
+		break;
+	case CM_422:
+		rc->initial_fullness_offset = (bpp >=  8) ? (2048) : ((bpp <=  7) ? (5632) : (5632 - dsc_roundf((bpp - 7) * (3584))));
+		rc->first_line_bpg_offset   = median3(0, (12 + (int) (0.09 *  min(34, slice_height - 8))), (int)((3 * bpc * 4) - (3 * bpp_group)));
+		rc->second_line_bpg_offset  = 0;
+		break;
+	case CM_444:
+	case CM_RGB:
+		rc->initial_fullness_offset = (bpp >= 12) ? (2048) : ((bpp <=  8) ? (6144) : ((((bpp >  8) && (bpp <= 10))) ? (6144 - dsc_roundf((bpp - 8) * (512 / 2))) : (5632 - dsc_roundf((bpp - 10) * (3584 / 2)))));
+		rc->first_line_bpg_offset   = median3(0, (12 + (int) (0.09 *  min(34, slice_height - 8))), (int)(((3 * bpc + (cm == CM_444 ? 0 : 2)) * 3) - (3 * bpp_group)));
+		rc->second_line_bpg_offset  = 0;
+		break;
+	}
+
+	initial_xmit_delay_factor = (cm == CM_444 || cm == CM_RGB) ? 1.0 : 2.0;
+	rc->initial_xmit_delay = dsc_roundf(8192.0/2.0/bpp/initial_xmit_delay_factor);
+
+	if (cm == CM_422 || cm == CM_420)
+		slice_width /= 2;
+
+	padding_pixels = ((slice_width % 3) != 0) ? (3 - (slice_width % 3)) * (rc->initial_xmit_delay / slice_width) : 0;
+	if (3 * bpp_group >= (((rc->initial_xmit_delay + 2) / 3) * (3 + (cm == CM_422)))) {
+		if ((rc->initial_xmit_delay + padding_pixels) % 3 == 1)
+			rc->initial_xmit_delay++;
+	}
+
+	rc->flatness_min_qp     = ((bpc == BPC_8) ?  (3) : ((bpc == BPC_10) ? (7)  : (11))) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
+	rc->flatness_max_qp     = ((bpc == BPC_8) ? (12) : ((bpc == BPC_10) ? (16) : (20))) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
+	rc->flatness_det_thresh = 2 << (bpc - 8);
+
+	get_qp_set(rc->qp_min, cm, bpc, DAL_MM_MIN, bpp);
+	get_qp_set(rc->qp_max, cm, bpc, DAL_MM_MAX, bpp);
+	if (cm == CM_444 && minor_version == 1) {
+		for (i = 0; i < QP_SET_SIZE; ++i) {
+			rc->qp_min[i] = rc->qp_min[i] > 0 ? rc->qp_min[i] - 1 : 0;
+			rc->qp_max[i] = rc->qp_max[i] > 0 ? rc->qp_max[i] - 1 : 0;
+		}
+	}
+	get_ofs_set(rc->ofs, cm, bpp);
+
+	/* fixed parameters */
+	rc->rc_model_size    = 8192;
+	rc->rc_edge_factor   = 6;
+	rc->rc_tgt_offset_hi = 3;
+	rc->rc_tgt_offset_lo = 3;
+
+	rc->rc_buf_thresh[0] = 896;
+	rc->rc_buf_thresh[1] = 1792;
+	rc->rc_buf_thresh[2] = 2688;
+	rc->rc_buf_thresh[3] = 3584;
+	rc->rc_buf_thresh[4] = 4480;
+	rc->rc_buf_thresh[5] = 5376;
+	rc->rc_buf_thresh[6] = 6272;
+	rc->rc_buf_thresh[7] = 6720;
+	rc->rc_buf_thresh[8] = 7168;
+	rc->rc_buf_thresh[9] = 7616;
+	rc->rc_buf_thresh[10] = 7744;
+	rc->rc_buf_thresh[11] = 7872;
+	rc->rc_buf_thresh[12] = 8000;
+	rc->rc_buf_thresh[13] = 8064;
+}
+
+u32 _do_bytes_per_pixel_calc(int slice_width,
+		u16 drm_bpp,
+		bool is_navite_422_or_420)
+{
+	float bpp;
+	u32 bytes_per_pixel;
+	double d_bytes_per_pixel;
+
+	dc_assert_fp_enabled();
+
+	bpp = ((float)drm_bpp / 16.0);
+	d_bytes_per_pixel = dsc_ceil(bpp * slice_width / 8.0) / slice_width;
+	// TODO: Make sure the formula for calculating this is precise (ceiling
+	// vs. floor, and at what point they should be applied)
+	if (is_navite_422_or_420)
+		d_bytes_per_pixel /= 2;
+
+	bytes_per_pixel = (u32)dsc_ceil(d_bytes_per_pixel * 0x10000000);
+
+	return bytes_per_pixel;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dml/dsc/rc_calc_fpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dml/dsc/rc_calc_fpu.h
@@ -0,0 +1,94 @@
+/*
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#ifndef __RC_CALC_FPU_H__
+#define __RC_CALC_FPU_H__
+
+#include "os_types.h"
+#include <drm/drm_dsc.h>
+
+#define QP_SET_SIZE 15
+
+typedef int qp_set[QP_SET_SIZE];
+
+struct rc_params {
+	int      rc_quant_incr_limit0;
+	int      rc_quant_incr_limit1;
+	int      initial_fullness_offset;
+	int      initial_xmit_delay;
+	int      first_line_bpg_offset;
+	int      second_line_bpg_offset;
+	int      flatness_min_qp;
+	int      flatness_max_qp;
+	int      flatness_det_thresh;
+	qp_set   qp_min;
+	qp_set   qp_max;
+	qp_set   ofs;
+	int      rc_model_size;
+	int      rc_edge_factor;
+	int      rc_tgt_offset_hi;
+	int      rc_tgt_offset_lo;
+	int      rc_buf_thresh[QP_SET_SIZE - 1];
+};
+
+enum colour_mode {
+	CM_RGB,   /* 444 RGB */
+	CM_444,   /* 444 YUV or simple 422 */
+	CM_422,   /* native 422 */
+	CM_420    /* native 420 */
+};
+
+enum bits_per_comp {
+	BPC_8  =  8,
+	BPC_10 = 10,
+	BPC_12 = 12
+};
+
+enum max_min {
+	DAL_MM_MIN = 0,
+	DAL_MM_MAX = 1
+};
+
+struct qp_entry {
+	float         bpp;
+	const qp_set  qps;
+};
+
+typedef struct qp_entry qp_table[];
+
+u32 _do_bytes_per_pixel_calc(int slice_width,
+		u16 drm_bpp,
+		bool is_navite_422_or_420);
+
+void _do_calc_rc_params(struct rc_params *rc,
+		enum colour_mode cm,
+		enum bits_per_comp bpc,
+		u16 drm_bpp,
+		bool is_navite_422_or_420,
+		int slice_width,
+		int slice_height,
+		int minor_version);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dsc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dsc/Makefile
@@ -1,35 +1,6 @@
 # SPDX-License-Identifier: MIT
 #
 # Makefile for the 'dsc' sub-component of DAL.
-
-ifdef CONFIG_X86
-dsc_ccflags := -mhard-float -msse
-endif
-
-ifdef CONFIG_PPC64
-dsc_ccflags := -mhard-float -maltivec
-endif
-
-ifdef CONFIG_CC_IS_GCC
-ifeq ($(call cc-ifversion, -lt, 0701, y), y)
-IS_OLD_GCC = 1
-endif
-endif
-
-ifdef CONFIG_X86
-ifdef IS_OLD_GCC
-# Stack alignment mismatch, proceed with caution.
-# GCC < 7.1 cannot compile code using `double` and -mpreferred-stack-boundary=3
-# (8B stack alignment).
-dsc_ccflags += -mpreferred-stack-boundary=4
-else
-dsc_ccflags += -msse2
-endif
-endif
-
-CFLAGS_$(AMDDALPATH)/dc/dsc/rc_calc.o := $(dsc_ccflags)
-CFLAGS_REMOVE_$(AMDDALPATH)/dc/dsc/rc_calc.o := $(dsc_rcflags)
-
 DSC = dc_dsc.o rc_calc.o rc_calc_dpi.o
 
 AMD_DAL_DSC = $(addprefix $(AMDDALPATH)/dc/dsc/,$(DSC))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dsc/dc_dsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dsc/dc_dsc.c
@@ -939,7 +939,12 @@
 	if (!is_dsc_possible)
 		goto done;
 
-	dsc_cfg->num_slices_v = pic_height/slice_height;
+	if (slice_height > 0) {
+		dsc_cfg->num_slices_v = pic_height / slice_height;
+	} else {
+		is_dsc_possible = false;
+		goto done;
+	}
 
 	if (target_bandwidth_kbps > 0) {
 		is_dsc_possible = decide_dsc_target_bpp_x16(
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dsc/rc_calc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dsc/rc_calc.c
@@ -23,266 +23,7 @@
  * Authors: AMD
  *
  */
-#include <drm/drm_dsc.h>
-
-#include "os_types.h"
 #include "rc_calc.h"
-#include "qp_tables.h"
-
-#define table_hash(mode, bpc, max_min) ((mode << 16) | (bpc << 8) | max_min)
-
-#define MODE_SELECT(val444, val422, val420) \
-	(cm == CM_444 || cm == CM_RGB) ? (val444) : (cm == CM_422 ? (val422) : (val420))
-
-
-#define TABLE_CASE(mode, bpc, max)   case (table_hash(mode, BPC_##bpc, max)): \
-	table = qp_table_##mode##_##bpc##bpc_##max; \
-	table_size = sizeof(qp_table_##mode##_##bpc##bpc_##max)/sizeof(*qp_table_##mode##_##bpc##bpc_##max); \
-	break
-
-
-static void get_qp_set(qp_set qps, enum colour_mode cm, enum bits_per_comp bpc,
-		       enum max_min max_min, float bpp)
-{
-	int mode = MODE_SELECT(444, 422, 420);
-	int sel = table_hash(mode, bpc, max_min);
-	int table_size = 0;
-	int index;
-	const struct qp_entry *table = 0L;
-
-	// alias enum
-	enum { min = DAL_MM_MIN, max = DAL_MM_MAX };
-	switch (sel) {
-		TABLE_CASE(444,  8, max);
-		TABLE_CASE(444,  8, min);
-		TABLE_CASE(444, 10, max);
-		TABLE_CASE(444, 10, min);
-		TABLE_CASE(444, 12, max);
-		TABLE_CASE(444, 12, min);
-		TABLE_CASE(422,  8, max);
-		TABLE_CASE(422,  8, min);
-		TABLE_CASE(422, 10, max);
-		TABLE_CASE(422, 10, min);
-		TABLE_CASE(422, 12, max);
-		TABLE_CASE(422, 12, min);
-		TABLE_CASE(420,  8, max);
-		TABLE_CASE(420,  8, min);
-		TABLE_CASE(420, 10, max);
-		TABLE_CASE(420, 10, min);
-		TABLE_CASE(420, 12, max);
-		TABLE_CASE(420, 12, min);
-	}
-
-	if (table == 0)
-		return;
-
-	index = (bpp - table[0].bpp) * 2;
-
-	/* requested size is bigger than the table */
-	if (index >= table_size) {
-		dm_error("ERROR: Requested rc_calc to find a bpp entry that exceeds the table size\n");
-		return;
-	}
-
-	memcpy(qps, table[index].qps, sizeof(qp_set));
-}
-
-static double dsc_roundf(double num)
-{
-	if (num < 0.0)
-		num = num - 0.5;
-	else
-		num = num + 0.5;
-
-	return (int)(num);
-}
-
-static double dsc_ceil(double num)
-{
-	double retval = (int)num;
-
-	if (retval != num && num > 0)
-		retval = num + 1;
-
-	return (int)retval;
-}
-
-static void get_ofs_set(qp_set ofs, enum colour_mode mode, float bpp)
-{
-	int   *p = ofs;
-
-	if (mode == CM_444 || mode == CM_RGB) {
-		*p++ = (bpp <=  6) ? (0) : ((((bpp >=  8) && (bpp <= 12))) ? (2) : ((bpp >= 15) ? (10) : ((((bpp > 6) && (bpp < 8))) ? (0 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (2 + dsc_roundf((bpp - 12) * (8 / 3.0))))));
-		*p++ = (bpp <=  6) ? (-2) : ((((bpp >=  8) && (bpp <= 12))) ? (0) : ((bpp >= 15) ? (8) : ((((bpp > 6) && (bpp < 8))) ? (-2 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (0 + dsc_roundf((bpp - 12) * (8 / 3.0))))));
-		*p++ = (bpp <=  6) ? (-2) : ((((bpp >=  8) && (bpp <= 12))) ? (0) : ((bpp >= 15) ? (6) : ((((bpp > 6) && (bpp < 8))) ? (-2 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (0 + dsc_roundf((bpp - 12) * (6 / 3.0))))));
-		*p++ = (bpp <=  6) ? (-4) : ((((bpp >=  8) && (bpp <= 12))) ? (-2) : ((bpp >= 15) ? (4) : ((((bpp > 6) && (bpp < 8))) ? (-4 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (-2 + dsc_roundf((bpp - 12) * (6 / 3.0))))));
-		*p++ = (bpp <=  6) ? (-6) : ((((bpp >=  8) && (bpp <= 12))) ? (-4) : ((bpp >= 15) ? (2) : ((((bpp > 6) && (bpp < 8))) ? (-6 + dsc_roundf((bpp -  6) * (2 / 2.0))) : (-4 + dsc_roundf((bpp - 12) * (6 / 3.0))))));
-		*p++ = (bpp <= 12) ? (-6) : ((bpp >= 15) ? (0) : (-6 + dsc_roundf((bpp - 12) * (6 / 3.0))));
-		*p++ = (bpp <= 12) ? (-8) : ((bpp >= 15) ? (-2) : (-8 + dsc_roundf((bpp - 12) * (6 / 3.0))));
-		*p++ = (bpp <= 12) ? (-8) : ((bpp >= 15) ? (-4) : (-8 + dsc_roundf((bpp - 12) * (4 / 3.0))));
-		*p++ = (bpp <= 12) ? (-8) : ((bpp >= 15) ? (-6) : (-8 + dsc_roundf((bpp - 12) * (2 / 3.0))));
-		*p++ = (bpp <= 12) ? (-10) : ((bpp >= 15) ? (-8) : (-10 + dsc_roundf((bpp - 12) * (2 / 3.0))));
-		*p++ = -10;
-		*p++ = (bpp <=  6) ? (-12) : ((bpp >=  8) ? (-10) : (-12 + dsc_roundf((bpp -  6) * (2 / 2.0))));
-		*p++ = -12;
-		*p++ = -12;
-		*p++ = -12;
-	} else if (mode == CM_422) {
-		*p++ = (bpp <=  8) ? (2) : ((bpp >= 10) ? (10) : (2 + dsc_roundf((bpp -  8) * (8 / 2.0))));
-		*p++ = (bpp <=  8) ? (0) : ((bpp >= 10) ? (8) : (0 + dsc_roundf((bpp -  8) * (8 / 2.0))));
-		*p++ = (bpp <=  8) ? (0) : ((bpp >= 10) ? (6) : (0 + dsc_roundf((bpp -  8) * (6 / 2.0))));
-		*p++ = (bpp <=  8) ? (-2) : ((bpp >= 10) ? (4) : (-2 + dsc_roundf((bpp -  8) * (6 / 2.0))));
-		*p++ = (bpp <=  8) ? (-4) : ((bpp >= 10) ? (2) : (-4 + dsc_roundf((bpp -  8) * (6 / 2.0))));
-		*p++ = (bpp <=  8) ? (-6) : ((bpp >= 10) ? (0) : (-6 + dsc_roundf((bpp -  8) * (6 / 2.0))));
-		*p++ = (bpp <=  8) ? (-8) : ((bpp >= 10) ? (-2) : (-8 + dsc_roundf((bpp -  8) * (6 / 2.0))));
-		*p++ = (bpp <=  8) ? (-8) : ((bpp >= 10) ? (-4) : (-8 + dsc_roundf((bpp -  8) * (4 / 2.0))));
-		*p++ = (bpp <=  8) ? (-8) : ((bpp >= 10) ? (-6) : (-8 + dsc_roundf((bpp -  8) * (2 / 2.0))));
-		*p++ = (bpp <=  8) ? (-10) : ((bpp >= 10) ? (-8) : (-10 + dsc_roundf((bpp -  8) * (2 / 2.0))));
-		*p++ = -10;
-		*p++ = (bpp <=  6) ? (-12) : ((bpp >= 7) ? (-10) : (-12 + dsc_roundf((bpp -  6) * (2.0 / 1))));
-		*p++ = -12;
-		*p++ = -12;
-		*p++ = -12;
-	} else {
-		*p++ = (bpp <=  6) ? (2) : ((bpp >=  8) ? (10) : (2 + dsc_roundf((bpp -  6) * (8 / 2.0))));
-		*p++ = (bpp <=  6) ? (0) : ((bpp >=  8) ? (8) : (0 + dsc_roundf((bpp -  6) * (8 / 2.0))));
-		*p++ = (bpp <=  6) ? (0) : ((bpp >=  8) ? (6) : (0 + dsc_roundf((bpp -  6) * (6 / 2.0))));
-		*p++ = (bpp <=  6) ? (-2) : ((bpp >=  8) ? (4) : (-2 + dsc_roundf((bpp -  6) * (6 / 2.0))));
-		*p++ = (bpp <=  6) ? (-4) : ((bpp >=  8) ? (2) : (-4 + dsc_roundf((bpp -  6) * (6 / 2.0))));
-		*p++ = (bpp <=  6) ? (-6) : ((bpp >=  8) ? (0) : (-6 + dsc_roundf((bpp -  6) * (6 / 2.0))));
-		*p++ = (bpp <=  6) ? (-8) : ((bpp >=  8) ? (-2) : (-8 + dsc_roundf((bpp -  6) * (6 / 2.0))));
-		*p++ = (bpp <=  6) ? (-8) : ((bpp >=  8) ? (-4) : (-8 + dsc_roundf((bpp -  6) * (4 / 2.0))));
-		*p++ = (bpp <=  6) ? (-8) : ((bpp >=  8) ? (-6) : (-8 + dsc_roundf((bpp -  6) * (2 / 2.0))));
-		*p++ = (bpp <=  6) ? (-10) : ((bpp >=  8) ? (-8) : (-10 + dsc_roundf((bpp -  6) * (2 / 2.0))));
-		*p++ = -10;
-		*p++ = (bpp <=  4) ? (-12) : ((bpp >=  5) ? (-10) : (-12 + dsc_roundf((bpp -  4) * (2 / 1.0))));
-		*p++ = -12;
-		*p++ = -12;
-		*p++ = -12;
-	}
-}
-
-static int median3(int a, int b, int c)
-{
-	if (a > b)
-		swap(a, b);
-	if (b > c)
-		swap(b, c);
-	if (a > b)
-		swap(b, c);
-
-	return b;
-}
-
-static void _do_calc_rc_params(struct rc_params *rc, enum colour_mode cm,
-			       enum bits_per_comp bpc, u16 drm_bpp,
-			       bool is_navite_422_or_420,
-			       int slice_width, int slice_height,
-			       int minor_version)
-{
-	float bpp;
-	float bpp_group;
-	float initial_xmit_delay_factor;
-	int padding_pixels;
-	int i;
-
-	bpp = ((float)drm_bpp / 16.0);
-	/* in native_422 or native_420 modes, the bits_per_pixel is double the
-	 * target bpp (the latter is what calc_rc_params expects)
-	 */
-	if (is_navite_422_or_420)
-		bpp /= 2.0;
-
-	rc->rc_quant_incr_limit0 = ((bpc == BPC_8) ? 11 : (bpc == BPC_10 ? 15 : 19)) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
-	rc->rc_quant_incr_limit1 = ((bpc == BPC_8) ? 11 : (bpc == BPC_10 ? 15 : 19)) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
-
-	bpp_group = MODE_SELECT(bpp, bpp * 2.0, bpp * 2.0);
-
-	switch (cm) {
-	case CM_420:
-		rc->initial_fullness_offset = (bpp >=  6) ? (2048) : ((bpp <=  4) ? (6144) : ((((bpp >  4) && (bpp <=  5))) ? (6144 - dsc_roundf((bpp - 4) * (512))) : (5632 - dsc_roundf((bpp -  5) * (3584)))));
-		rc->first_line_bpg_offset   = median3(0, (12 + (int) (0.09 *  min(34, slice_height - 8))), (int)((3 * bpc * 3) - (3 * bpp_group)));
-		rc->second_line_bpg_offset  = median3(0, 12, (int)((3 * bpc * 3) - (3 * bpp_group)));
-		break;
-	case CM_422:
-		rc->initial_fullness_offset = (bpp >=  8) ? (2048) : ((bpp <=  7) ? (5632) : (5632 - dsc_roundf((bpp - 7) * (3584))));
-		rc->first_line_bpg_offset   = median3(0, (12 + (int) (0.09 *  min(34, slice_height - 8))), (int)((3 * bpc * 4) - (3 * bpp_group)));
-		rc->second_line_bpg_offset  = 0;
-		break;
-	case CM_444:
-	case CM_RGB:
-		rc->initial_fullness_offset = (bpp >= 12) ? (2048) : ((bpp <=  8) ? (6144) : ((((bpp >  8) && (bpp <= 10))) ? (6144 - dsc_roundf((bpp - 8) * (512 / 2))) : (5632 - dsc_roundf((bpp - 10) * (3584 / 2)))));
-		rc->first_line_bpg_offset   = median3(0, (12 + (int) (0.09 *  min(34, slice_height - 8))), (int)(((3 * bpc + (cm == CM_444 ? 0 : 2)) * 3) - (3 * bpp_group)));
-		rc->second_line_bpg_offset  = 0;
-		break;
-	}
-
-	initial_xmit_delay_factor = (cm == CM_444 || cm == CM_RGB) ? 1.0 : 2.0;
-	rc->initial_xmit_delay = dsc_roundf(8192.0/2.0/bpp/initial_xmit_delay_factor);
-
-	if (cm == CM_422 || cm == CM_420)
-		slice_width /= 2;
-
-	padding_pixels = ((slice_width % 3) != 0) ? (3 - (slice_width % 3)) * (rc->initial_xmit_delay / slice_width) : 0;
-	if (3 * bpp_group >= (((rc->initial_xmit_delay + 2) / 3) * (3 + (cm == CM_422)))) {
-		if ((rc->initial_xmit_delay + padding_pixels) % 3 == 1)
-			rc->initial_xmit_delay++;
-	}
-
-	rc->flatness_min_qp     = ((bpc == BPC_8) ?  (3) : ((bpc == BPC_10) ? (7)  : (11))) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
-	rc->flatness_max_qp     = ((bpc == BPC_8) ? (12) : ((bpc == BPC_10) ? (16) : (20))) - ((minor_version == 1 && cm == CM_444) ? 1 : 0);
-	rc->flatness_det_thresh = 2 << (bpc - 8);
-
-	get_qp_set(rc->qp_min, cm, bpc, DAL_MM_MIN, bpp);
-	get_qp_set(rc->qp_max, cm, bpc, DAL_MM_MAX, bpp);
-	if (cm == CM_444 && minor_version == 1) {
-		for (i = 0; i < QP_SET_SIZE; ++i) {
-			rc->qp_min[i] = rc->qp_min[i] > 0 ? rc->qp_min[i] - 1 : 0;
-			rc->qp_max[i] = rc->qp_max[i] > 0 ? rc->qp_max[i] - 1 : 0;
-		}
-	}
-	get_ofs_set(rc->ofs, cm, bpp);
-
-	/* fixed parameters */
-	rc->rc_model_size    = 8192;
-	rc->rc_edge_factor   = 6;
-	rc->rc_tgt_offset_hi = 3;
-	rc->rc_tgt_offset_lo = 3;
-
-	rc->rc_buf_thresh[0] = 896;
-	rc->rc_buf_thresh[1] = 1792;
-	rc->rc_buf_thresh[2] = 2688;
-	rc->rc_buf_thresh[3] = 3584;
-	rc->rc_buf_thresh[4] = 4480;
-	rc->rc_buf_thresh[5] = 5376;
-	rc->rc_buf_thresh[6] = 6272;
-	rc->rc_buf_thresh[7] = 6720;
-	rc->rc_buf_thresh[8] = 7168;
-	rc->rc_buf_thresh[9] = 7616;
-	rc->rc_buf_thresh[10] = 7744;
-	rc->rc_buf_thresh[11] = 7872;
-	rc->rc_buf_thresh[12] = 8000;
-	rc->rc_buf_thresh[13] = 8064;
-}
-
-static u32 _do_bytes_per_pixel_calc(int slice_width, u16 drm_bpp,
-				    bool is_navite_422_or_420)
-{
-	float bpp;
-	u32 bytes_per_pixel;
-	double d_bytes_per_pixel;
-
-	bpp = ((float)drm_bpp / 16.0);
-	d_bytes_per_pixel = dsc_ceil(bpp * slice_width / 8.0) / slice_width;
-	// TODO: Make sure the formula for calculating this is precise (ceiling
-	// vs. floor, and at what point they should be applied)
-	if (is_navite_422_or_420)
-		d_bytes_per_pixel /= 2;
-
-	bytes_per_pixel = (u32)dsc_ceil(d_bytes_per_pixel * 0x10000000);
-
-	return bytes_per_pixel;
-}
 
 /**
  * calc_rc_params - reads the user's cmdline mode
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dsc/rc_calc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dsc/rc_calc.h
@@ -27,55 +27,7 @@
 #ifndef __RC_CALC_H__
 #define __RC_CALC_H__
 
-
-#define QP_SET_SIZE 15
-
-typedef int qp_set[QP_SET_SIZE];
-
-struct rc_params {
-	int      rc_quant_incr_limit0;
-	int      rc_quant_incr_limit1;
-	int      initial_fullness_offset;
-	int      initial_xmit_delay;
-	int      first_line_bpg_offset;
-	int      second_line_bpg_offset;
-	int      flatness_min_qp;
-	int      flatness_max_qp;
-	int      flatness_det_thresh;
-	qp_set   qp_min;
-	qp_set   qp_max;
-	qp_set   ofs;
-	int      rc_model_size;
-	int      rc_edge_factor;
-	int      rc_tgt_offset_hi;
-	int      rc_tgt_offset_lo;
-	int      rc_buf_thresh[QP_SET_SIZE - 1];
-};
-
-enum colour_mode {
-	CM_RGB,   /* 444 RGB */
-	CM_444,   /* 444 YUV or simple 422 */
-	CM_422,   /* native 422 */
-	CM_420    /* native 420 */
-};
-
-enum bits_per_comp {
-	BPC_8  =  8,
-	BPC_10 = 10,
-	BPC_12 = 12
-};
-
-enum max_min {
-	DAL_MM_MIN = 0,
-	DAL_MM_MAX = 1
-};
-
-struct qp_entry {
-	float         bpp;
-	const qp_set  qps;
-};
-
-typedef struct qp_entry qp_table[];
+#include "dml/dsc/rc_calc_fpu.h"
 
 void calc_rc_params(struct rc_params *rc, const struct drm_dsc_config *pps);
 u32 calc_dsc_bytes_per_pixel(const struct drm_dsc_config *pps);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/dsc/rc_calc_dpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/dsc/rc_calc_dpi.c
@@ -22,7 +22,6 @@
  * Authors: AMD
  *
  */
-#include "os_types.h"
 #include <drm/drm_dsc.h>
 #include "dscc_types.h"
 #include "rc_calc.h"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/gpio/gpio_service.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/gpio/gpio_service.c
@@ -58,7 +58,7 @@
 	struct dc_context *ctx)
 {
 	struct gpio_service *service;
-	uint32_t index_of_id;
+	int32_t index_of_id;
 
 	service = kzalloc(sizeof(struct gpio_service), GFP_KERNEL);
 
@@ -114,7 +114,7 @@
 	return service;
 
 failure_2:
-	while (index_of_id) {
+	while (index_of_id > 0) {
 		--index_of_id;
 		kfree(service->busyness[index_of_id]);
 	}
@@ -241,6 +241,9 @@
 	enum gpio_id id,
 	uint32_t en)
 {
+	if (id == GPIO_ID_UNKNOWN)
+		return false;
+
 	return service->busyness[id][en];
 }
 
@@ -249,6 +252,9 @@
 	enum gpio_id id,
 	uint32_t en)
 {
+	if (id == GPIO_ID_UNKNOWN)
+		return;
+
 	service->busyness[id][en] = true;
 }
 
@@ -257,6 +263,9 @@
 	enum gpio_id id,
 	uint32_t en)
 {
+	if (id == GPIO_ID_UNKNOWN)
+		return;
+
 	service->busyness[id][en] = false;
 }
 
@@ -265,7 +274,7 @@
 	enum gpio_id id,
 	uint32_t en)
 {
-	if (!service->busyness[id]) {
+	if (id != GPIO_ID_UNKNOWN && !service->busyness[id]) {
 		ASSERT_CRITICAL(false);
 		return GPIO_RESULT_OPEN_FAILED;
 	}
@@ -279,7 +288,7 @@
 	enum gpio_id id,
 	uint32_t en)
 {
-	if (!service->busyness[id]) {
+	if (id != GPIO_ID_UNKNOWN && !service->busyness[id]) {
 		ASSERT_CRITICAL(false);
 		return GPIO_RESULT_OPEN_FAILED;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/hdcp/hdcp_msg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/hdcp/hdcp_msg.c
@@ -131,13 +131,21 @@
 	const uint8_t hdcp_i2c_addr_link_primary = 0x3a; /* 0x74 >> 1*/
 	const uint8_t hdcp_i2c_addr_link_secondary = 0x3b; /* 0x76 >> 1*/
 	struct i2c_command i2c_command;
-	uint8_t offset = hdcp_i2c_offsets[message_info->msg_id];
+	uint8_t offset;
 	struct i2c_payload i2c_payloads[] = {
-		{ true, 0, 1, &offset },
+		{ true, 0, 1, 0 },
 		/* actual hdcp payload, will be filled later, zeroed for now*/
 		{ 0 }
 	};
 
+	if (message_info->msg_id == HDCP_MESSAGE_ID_INVALID) {
+		DC_LOG_ERROR("%s: Invalid message_info msg_id - %d\n", __func__, message_info->msg_id);
+		return false;
+	}
+
+	offset = hdcp_i2c_offsets[message_info->msg_id];
+	i2c_payloads[0].data = &offset;
+
 	switch (message_info->link) {
 	case HDCP_LINK_SECONDARY:
 		i2c_payloads[0].address = hdcp_i2c_addr_link_secondary;
@@ -311,6 +319,11 @@
 	struct dc_link *link,
 	struct hdcp_protection_message *message_info)
 {
+	if (message_info->msg_id == HDCP_MESSAGE_ID_INVALID) {
+		DC_LOG_ERROR("%s: Invalid message_info msg_id - %d\n", __func__, message_info->msg_id);
+		return false;
+	}
+
 	return dpcd_access_helper(
 		link,
 		message_info->length,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/core_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/core_types.h
@@ -62,6 +62,7 @@
 	uint32_t connector_index; /* this will be mapped to the HPD pins */
 	uint32_t link_index; /* this is mapped to DAL display_index
 				TODO: remove it when DC is complete. */
+	bool is_dpia_link;
 };
 
 struct dc_link *link_create(const struct link_init_data *init_params);
@@ -245,6 +246,8 @@
 	 * entries in link_encoders array.
 	 */
 	unsigned int dig_link_enc_count;
+	/* Number of USB4 DPIA (DisplayPort Input Adapter) link objects created.*/
+	unsigned int usb4_dpia_count;
 
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 	struct dc_3dlut *mpc_lut[MAX_PIPES];
@@ -375,6 +378,17 @@
 	bool vtp_locked;
 };
 
+/* Data used for dynamic link encoder assignment.
+ * Tracks current and future assignments; available link encoders;
+ * and mode of operation (whether to use current or future assignments).
+ */
+struct link_enc_cfg_context {
+	enum link_enc_cfg_mode mode;
+	struct link_enc_assignment link_enc_assignments[MAX_PIPES];
+	enum engine_id link_enc_avail[MAX_DIG_LINK_ENCODERS];
+	struct link_enc_assignment transient_assignments[MAX_PIPES];
+};
+
 struct resource_context {
 	struct pipe_ctx pipe_ctx[MAX_PIPES];
 	bool is_stream_enc_acquired[MAX_PIPES * 2];
@@ -382,12 +396,7 @@
 	uint8_t clock_source_ref_count[MAX_CLOCK_SOURCES];
 	uint8_t dp_clock_source_ref_count;
 	bool is_dsc_acquired[MAX_PIPES];
-	/* A table/array of encoder-to-link assignments. One entry per stream.
-	 * Indexed by stream index in dc_state.
-	 */
-	struct link_enc_assignment link_enc_assignments[MAX_PIPES];
-	/* List of available link encoders. Uses engine ID as encoder identifier. */
-	enum engine_id link_enc_avail[MAX_DIG_LINK_ENCODERS];
+	struct link_enc_cfg_context link_enc_cfg_ctx;
 #if defined(CONFIG_DRM_AMD_DC_DCN)
 	bool is_mpc_3dlut_acquired[MAX_PIPES];
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/dc_link_ddc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/dc_link_ddc.h
@@ -69,6 +69,7 @@
 	struct graphics_object_id id;
 	struct dc_context *ctx;
 	struct dc_link *link;
+	bool is_dpia_link;
 };
 
 struct ddc_service *dal_ddc_service_create(
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/dc_link_dp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/dc_link_dp.h
@@ -188,6 +188,10 @@
 		struct dc_link *link,
 		struct link_training_settings *lt_settings);
 
+enum dc_status dpcd_configure_channel_coding(
+		struct dc_link *link,
+		struct link_training_settings *lt_settings);
+
 enum dp_link_encoding dp_get_link_encoding_format(const struct dc_link_settings *link_settings);
 bool dp_retrieve_lttpr_cap(struct dc_link *link);
 #endif /* __DC_LINK_DP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/dc_link_dpia.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/dc_link_dpia.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: AMD
+ *
+ */
+
+#ifndef __DC_LINK_DPIA_H__
+#define __DC_LINK_DPIA_H__
+
+/* This module implements functionality for training DPIA links. */
+
+struct dc_link;
+struct dc_link_settings;
+
+/* The approximate time (us) it takes to transmit 9 USB4 DP clock sync packets. */
+#define DPIA_CLK_SYNC_DELAY 16000
+
+/* Extend interval between training status checks for manual testing. */
+#define DPIA_DEBUG_EXTENDED_AUX_RD_INTERVAL_US 60000000
+
+/** @note Can remove once DP tunneling registers in upstream include/drm/drm_dp_helper.h */
+/* DPCD DP Tunneling over USB4 */
+#define DP_TUNNELING_CAPABILITIES_SUPPORT 0xe000d
+#define DP_IN_ADAPTER_INFO                0xe000e
+#define DP_USB4_DRIVER_ID                 0xe000f
+#define DP_USB4_ROUTER_TOPOLOGY_ID        0xe001b
+
+/* SET_CONFIG message types sent by driver. */
+enum dpia_set_config_type {
+	DPIA_SET_CFG_SET_LINK = 0x01,
+	DPIA_SET_CFG_SET_PHY_TEST_MODE = 0x05,
+	DPIA_SET_CFG_SET_TRAINING = 0x18,
+	DPIA_SET_CFG_SET_VSPE = 0x19
+};
+
+/* Training stages (TS) in SET_CONFIG(SET_TRAINING) message. */
+enum dpia_set_config_ts {
+	DPIA_TS_DPRX_DONE = 0x00, /* Done training DPRX. */
+	DPIA_TS_TPS1 = 0x01,
+	DPIA_TS_TPS2 = 0x02,
+	DPIA_TS_TPS3 = 0x03,
+	DPIA_TS_TPS4 = 0x07,
+	DPIA_TS_UFP_DONE = 0xff /* Done training DPTX-to-DPIA hop. */
+};
+
+/* SET_CONFIG message data associated with messages sent by driver. */
+union dpia_set_config_data {
+	struct {
+		uint8_t mode : 1;
+		uint8_t reserved : 7;
+	} set_link;
+	struct {
+		uint8_t stage;
+	} set_training;
+	struct {
+		uint8_t swing : 2;
+		uint8_t max_swing_reached : 1;
+		uint8_t pre_emph : 2;
+		uint8_t max_pre_emph_reached : 1;
+		uint8_t reserved : 2;
+	} set_vspe;
+	uint8_t raw;
+};
+
+/* Read tunneling device capability from DPCD and update link capability
+ * accordingly.
+ */
+enum dc_status dpcd_get_tunneling_device_data(struct dc_link *link);
+
+/* Train DP tunneling link for USB4 DPIA display endpoint.
+ * DPIA equivalent of dc_link_dp_perfrorm_link_training.
+ * Aborts link training upon detection of sink unplug.
+ */
+enum link_training_result
+dc_link_dpia_perform_link_training(struct dc_link *link,
+	const struct dc_link_settings *link_setting,
+	bool skip_video_pattern);
+
+#endif /* __DC_LINK_DPIA_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/hw/dchubbub.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/hw/dchubbub.h
@@ -154,6 +154,8 @@
 	bool (*is_allow_self_refresh_enabled)(struct hubbub *hubbub);
 	void (*allow_self_refresh_control)(struct hubbub *hubbub, bool allow);
 
+	bool (*verify_allow_pstate_change_high)(struct hubbub *hubbub);
+
 	void (*apply_DEDCN21_147_wa)(struct hubbub *hubbub);
 
 	void (*force_wm_propagate_to_pipes)(struct hubbub *hubbub);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/hw/link_encoder.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/hw/link_encoder.h
@@ -208,6 +208,12 @@
 	bool valid;
 	struct display_endpoint_id ep_id;
 	enum engine_id eng_id;
+	struct dc_stream_state *stream;
+};
+
+enum link_enc_cfg_mode {
+	LINK_ENC_CFG_STEADY, /* Normal operation - use current_state. */
+	LINK_ENC_CFG_TRANSIENT /* During commit state - use state to be committed. */
 };
 
 #endif /* LINK_ENCODER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/hw/stream_encoder.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/hw/stream_encoder.h
@@ -165,9 +165,11 @@
 		struct stream_encoder *enc);
 
 	void (*dp_blank)(
+		struct dc_link *link,
 		struct stream_encoder *enc);
 
 	void (*dp_unblank)(
+		struct dc_link *link,
 		struct stream_encoder *enc,
 		const struct encoder_unblank_param *param);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/hw_sequencer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/hw_sequencer.h
@@ -32,11 +32,6 @@
 #include "inc/hw/link_encoder.h"
 #include "core_status.h"
 
-enum vline_select {
-	VLINE0,
-	VLINE1
-};
-
 struct pipe_ctx;
 struct dc_state;
 struct dc_stream_status;
@@ -115,8 +110,7 @@
 			int group_index, int group_size,
 			struct pipe_ctx *grouped_pipes[]);
 	void (*setup_periodic_interrupt)(struct dc *dc,
-			struct pipe_ctx *pipe_ctx,
-			enum vline_select vline);
+			struct pipe_ctx *pipe_ctx);
 	void (*set_drr)(struct pipe_ctx **pipe_ctx, int num_pipes,
 			struct dc_crtc_timing_adjust adjust);
 	void (*set_static_screen_control)(struct pipe_ctx **pipe_ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/link_enc_cfg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/link_enc_cfg.h
@@ -36,7 +36,7 @@
  * Initialise link encoder resource tracking.
  */
 void link_enc_cfg_init(
-		struct dc *dc,
+		const struct dc *dc,
 		struct dc_state *state);
 
 /*
@@ -70,22 +70,36 @@
  * endpoint.
  */
 bool link_enc_cfg_is_transmitter_mappable(
-		struct dc_state *state,
+		struct dc *dc,
 		struct link_encoder *link_enc);
 
+/* Return stream using DIG link encoder resource. NULL if unused. */
+struct dc_stream_state *link_enc_cfg_get_stream_using_link_enc(
+		struct dc *dc,
+		enum engine_id eng_id);
+
 /* Return link using DIG link encoder resource. NULL if unused. */
 struct dc_link *link_enc_cfg_get_link_using_link_enc(
-		struct dc_state *state,
+		struct dc *dc,
 		enum engine_id eng_id);
 
 /* Return DIG link encoder used by link. NULL if unused. */
 struct link_encoder *link_enc_cfg_get_link_enc_used_by_link(
-		struct dc_state *state,
+		struct dc *dc,
 		const struct dc_link *link);
 
 /* Return next available DIG link encoder. NULL if none available. */
-struct link_encoder *link_enc_cfg_get_next_avail_link_enc(
-	const struct dc *dc,
-	const struct dc_state *state);
+struct link_encoder *link_enc_cfg_get_next_avail_link_enc(struct dc *dc);
+
+/* Return DIG link encoder used by stream. NULL if unused. */
+struct link_encoder *link_enc_cfg_get_link_enc_used_by_stream(
+		struct dc *dc,
+		const struct dc_stream_state *stream);
+
+/* Return true if encoder available to use. */
+bool link_enc_cfg_is_link_enc_avail(struct dc *dc, enum engine_id eng_id);
+
+/* Returns true if encoder assignments in supplied state pass validity checks. */
+bool link_enc_cfg_validate(struct dc *dc, struct dc_state *state);
 
 #endif /* DC_INC_LINK_ENC_CFG_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/link_hwss.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/link_hwss.h
@@ -37,6 +37,7 @@
 	const struct dc_link_settings *link_settings);
 
 void dp_receiver_power_ctrl(struct dc_link *link, bool on);
+void dp_source_sequence_trace(struct dc_link *link, uint8_t dp_test_mode);
 void edp_add_delay_for_T9(struct dc_link *link);
 bool edp_receiver_ready_T9(struct dc_link *link);
 bool edp_receiver_ready_T7(struct dc_link *link);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/inc/resource.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/inc/resource.h
@@ -49,6 +49,7 @@
 	int num_vmid;
 	int num_dsc;
 	unsigned int num_dig_link_enc; // Total number of DIGs (digital encoders) in DIO (Display Input/Output).
+	unsigned int num_usb4_dpia; // Total number of USB4 DPIA (DisplayPort Input Adapters).
 	int num_mpc_3dlut;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/irq/dce110/irq_service_dce110.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/irq/dce110/irq_service_dce110.c
@@ -211,8 +211,12 @@
 						   info->ext_id);
 	uint8_t pipe_offset = dal_irq_src - IRQ_TYPE_VBLANK;
 
-	struct timing_generator *tg =
-			dc->current_state->res_ctx.pipe_ctx[pipe_offset].stream_res.tg;
+	struct timing_generator *tg;
+
+	if (pipe_offset >= MAX_PIPES)
+		return false;
+
+	tg = dc->current_state->res_ctx.pipe_ctx[pipe_offset].stream_res.tg;
 
 	if (enable) {
 		if (!tg || !tg->funcs->arm_vert_intr(tg, 2)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/irq/dcn21/irq_service_dcn21.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/irq/dcn21/irq_service_dcn21.c
@@ -266,14 +266,6 @@
 		.funcs = &pflip_irq_info_funcs\
 	}
 
-#define vupdate_int_entry(reg_num)\
-	[DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\
-		IRQ_REG_ENTRY(OTG, reg_num,\
-			OTG_GLOBAL_SYNC_STATUS, VUPDATE_INT_EN,\
-			OTG_GLOBAL_SYNC_STATUS, VUPDATE_EVENT_CLEAR),\
-		.funcs = &vblank_irq_info_funcs\
-	}
-
 /* vupdate_no_lock_int_entry maps to DC_IRQ_SOURCE_VUPDATEx, to match semantic
  * of DCE's DC_IRQ_SOURCE_VUPDATEx.
  */
@@ -402,12 +394,6 @@
 	dc_underflow_int_entry(6),
 	[DC_IRQ_SOURCE_DMCU_SCP] = dummy_irq_entry(),
 	[DC_IRQ_SOURCE_VBIOS_SW] = dummy_irq_entry(),
-	vupdate_int_entry(0),
-	vupdate_int_entry(1),
-	vupdate_int_entry(2),
-	vupdate_int_entry(3),
-	vupdate_int_entry(4),
-	vupdate_int_entry(5),
 	vupdate_no_lock_int_entry(0),
 	vupdate_no_lock_int_entry(1),
 	vupdate_no_lock_int_entry(2),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/os_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/os_types.h
@@ -31,6 +31,7 @@
 #include <linux/kref.h>
 #include <linux/types.h>
 #include <linux/slab.h>
+#include <linux/delay.h>
 
 #include <asm/byteorder.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dc/virtual/virtual_stream_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dc/virtual/virtual_stream_encoder.c
@@ -69,9 +69,11 @@
 	struct stream_encoder *enc) {}
 
 static void virtual_stream_encoder_dp_blank(
+	struct dc_link *link,
 	struct stream_encoder *enc) {}
 
 static void virtual_stream_encoder_dp_unblank(
+	struct dc_link *link,
 	struct stream_encoder *enc,
 	const struct encoder_unblank_param *param) {}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dmub/dmub_srv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dmub/dmub_srv.h
@@ -96,6 +96,7 @@
 	DMUB_ASIC_DCN302,
 	DMUB_ASIC_DCN303,
 	DMUB_ASIC_DCN31,
+	DMUB_ASIC_DCN31B,
 	DMUB_ASIC_MAX,
 };
 
@@ -118,6 +119,7 @@
 	DMUB_NOTIFICATION_AUX_REPLY,
 	DMUB_NOTIFICATION_HPD,
 	DMUB_NOTIFICATION_HPD_IRQ,
+	DMUB_NOTIFICATION_SET_CONFIG_REPLY,
 	DMUB_NOTIFICATION_MAX
 };
 
@@ -166,6 +168,7 @@
 	uint32_t vbios_size;
 	const uint8_t *fw_inst_const;
 	const uint8_t *fw_bss_data;
+	bool is_mailbox_in_inbox;
 };
 
 /**
@@ -185,20 +188,25 @@
  */
 struct dmub_srv_region_info {
 	uint32_t fb_size;
+	uint32_t inbox_size;
 	uint8_t num_regions;
 	struct dmub_region regions[DMUB_WINDOW_TOTAL];
 };
 
 /**
- * struct dmub_srv_fb_params - parameters used for driver fb setup
+ * struct dmub_srv_memory_params - parameters used for driver fb setup
  * @region_info: region info calculated by dmub service
- * @cpu_addr: base cpu address for the framebuffer
- * @gpu_addr: base gpu virtual address for the framebuffer
+ * @cpu_fb_addr: base cpu address for the framebuffer
+ * @cpu_inbox_addr: base cpu address for the gart
+ * @gpu_fb_addr: base gpu virtual address for the framebuffer
+ * @gpu_inbox_addr: base gpu virtual address for the gart
  */
-struct dmub_srv_fb_params {
+struct dmub_srv_memory_params {
 	const struct dmub_srv_region_info *region_info;
-	void *cpu_addr;
-	uint64_t gpu_addr;
+	void *cpu_fb_addr;
+	void *cpu_inbox_addr;
+	uint64_t gpu_fb_addr;
+	uint64_t gpu_inbox_addr;
 };
 
 /**
@@ -235,6 +243,8 @@
 	bool load_inst_const;
 	bool skip_panel_power_sequence;
 	bool disable_z10;
+	bool dpia_supported;
+	bool disable_dpia;
 };
 
 /**
@@ -437,6 +447,7 @@
 	union {
 		struct aux_reply_data aux_reply;
 		enum dp_hpd_status hpd_status;
+		enum set_config_status sc_status;
 	};
 };
 
@@ -445,7 +456,7 @@
  * of a firmware to know if feature or functionality is supported or present.
  */
 #define DMUB_FW_VERSION(major, minor, revision) \
-	((((major) & 0xFF) << 24) | (((minor) & 0xFF) << 16) | ((revision) & 0xFFFF))
+	((((major) & 0xFF) << 24) | (((minor) & 0xFF) << 16) | (((revision) & 0xFF) << 8))
 
 /**
  * dmub_srv_create() - creates the DMUB service.
@@ -496,8 +507,8 @@
  *   DMUB_STATUS_OK - success
  *   DMUB_STATUS_INVALID - unspecified error
  */
-enum dmub_status dmub_srv_calc_fb_info(struct dmub_srv *dmub,
-				       const struct dmub_srv_fb_params *params,
+enum dmub_status dmub_srv_calc_mem_info(struct dmub_srv *dmub,
+				       const struct dmub_srv_memory_params *params,
 				       struct dmub_srv_fb_info *out);
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd.h
@@ -368,10 +368,15 @@
 		uint32_t disable_clk_gate: 1; /**< 1 if clock gating should be disabled */
 		uint32_t skip_phy_init_panel_sequence: 1; /**< 1 to skip panel init seq */
 		uint32_t z10_disable: 1; /**< 1 to disable z10 */
-		uint32_t reserved2: 1; /**< reserved for an unreleased feature */
-		uint32_t reserved_unreleased1: 1; /**< reserved for an unreleased feature */
+		uint32_t enable_dpia: 1; /**< 1 if DPIA should be enabled */
 		uint32_t invalid_vbios_data: 1; /**< 1 if VBIOS data table is invalid */
-		uint32_t reserved : 23; /**< reserved */
+		uint32_t dpia_supported: 1; /**< 1 if DPIA is supported on this platform */
+		uint32_t sel_mux_phy_c_d_phy_f_g: 1; /**< 1 if PHYF/PHYG should be enabled */
+		/**< 1 if all root clock gating is enabled and low power memory is enabled*/
+		uint32_t power_optimization: 1;
+		uint32_t diag_env: 1; /* 1 if diagnostic environment */
+
+		uint32_t reserved : 19; /**< reserved */
 	} bits; /**< boot bits */
 	uint32_t all; /**< 32-bit access to bits */
 };
@@ -411,7 +416,14 @@
 	 * Enables or disables power gating.
 	 */
 	DMUB_CMD__VBIOS_ENABLE_DISP_POWER_GATING = 3,
+	/**
+	 * Controls embedded panels.
+	 */
 	DMUB_CMD__VBIOS_LVTMA_CONTROL = 15,
+	/**
+	 * Query DP alt status on a transmitter.
+	 */
+	DMUB_CMD__VBIOS_TRANSMITTER_QUERY_DP_ALT  = 26,
 };
 
 //==============================================================================
@@ -653,6 +665,10 @@
 	 */
 	DMUB_CMD__PANEL_CNTL = 74,
 	/**
+	 * Command type used for interfacing with DPIA.
+	 */
+	DMUB_CMD__DPIA = 77,
+	/**
 	 * Command type used for EDID CEA parsing
 	 */
 	DMUB_CMD__EDID_CEA = 79,
@@ -674,6 +690,21 @@
 	 * Command type used for DP AUX Reply data notification
 	 */
 	DMUB_OUT_CMD__DP_AUX_REPLY = 1,
+	/**
+	 * Command type used for DP HPD event notification
+	 */
+	DMUB_OUT_CMD__DP_HPD_NOTIFY = 2,
+	/**
+	 * Command type used for SET_CONFIG Reply notification
+	 */
+	DMUB_OUT_CMD__SET_CONFIG_REPLY = 3,
+};
+
+/* DMUB_CMD__DPIA command sub-types. */
+enum dmub_cmd_dpia_type {
+	DMUB_CMD__DPIA_DIG1_DPIA_CONTROL = 0,
+	DMUB_CMD__DPIA_SET_CONFIG_ACCESS = 1,
+	DMUB_CMD__DPIA_MST_ALLOC_SLOTS = 2,
 };
 
 #pragma pack(push, 1)
@@ -996,6 +1027,77 @@
 };
 
 /**
+ * DPIA tunnel command parameters.
+ */
+struct dmub_cmd_dig_dpia_control_data {
+	uint8_t enc_id;         /** 0 = ENGINE_ID_DIGA, ... */
+	uint8_t action;         /** ATOM_TRANSMITER_ACTION_DISABLE/ENABLE/SETUP_VSEMPH */
+	union {
+		uint8_t digmode;    /** enum atom_encode_mode_def */
+		uint8_t dplaneset;  /** DP voltage swing and pre-emphasis value */
+	} mode_laneset;
+	uint8_t lanenum;        /** Lane number 1, 2, 4, 8 */
+	uint32_t symclk_10khz;  /** Symbol Clock in 10Khz */
+	uint8_t hpdsel;         /** =0: HPD is not assigned */
+	uint8_t digfe_sel;      /** DIG stream( front-end ) selection, bit0 - DIG0 FE */
+	uint8_t dpia_id;        /** Index of DPIA */
+	uint8_t fec_rdy : 1;
+	uint8_t reserved : 7;
+	uint32_t reserved1;
+};
+
+/**
+ * DMUB command for DPIA tunnel control.
+ */
+struct dmub_rb_cmd_dig1_dpia_control {
+	struct dmub_cmd_header header;
+	struct dmub_cmd_dig_dpia_control_data dpia_control;
+};
+
+/**
+ * SET_CONFIG Command Payload
+ */
+struct set_config_cmd_payload {
+	uint8_t msg_type; /* set config message type */
+	uint8_t msg_data; /* set config message data */
+};
+
+/**
+ * Data passed from driver to FW in a DMUB_CMD__DPIA_SET_CONFIG_ACCESS command.
+ */
+struct dmub_cmd_set_config_control_data {
+	struct set_config_cmd_payload cmd_pkt;
+	uint8_t instance; /* DPIA instance */
+	uint8_t immed_status; /* Immediate status returned in case of error */
+};
+
+/**
+ * DMUB command structure for SET_CONFIG command.
+ */
+struct dmub_rb_cmd_set_config_access {
+	struct dmub_cmd_header header; /* header */
+	struct dmub_cmd_set_config_control_data set_config_control; /* set config data */
+};
+
+/**
+ * Data passed from driver to FW in a DMUB_CMD__DPIA_MST_ALLOC_SLOTS command.
+ */
+struct dmub_cmd_mst_alloc_slots_control_data {
+	uint8_t mst_alloc_slots; /* mst slots to be allotted */
+	uint8_t instance; /* DPIA instance */
+	uint8_t immed_status; /* Immediate status returned as there is no outbox msg posted */
+	uint8_t mst_slots_in_use; /* returns slots in use for error cases */
+};
+
+/**
+ * DMUB command structure for SET_ command.
+ */
+struct dmub_rb_cmd_set_mst_alloc_slots {
+	struct dmub_cmd_header header; /* header */
+	struct dmub_cmd_mst_alloc_slots_control_data mst_slots_control; /* mst slots control */
+};
+
+/**
  * struct dmub_rb_cmd_dpphy_init - DPPHY init.
  */
 struct dmub_rb_cmd_dpphy_init {
@@ -1242,6 +1344,33 @@
 	struct dp_hpd_data hpd_data;
 };
 
+/**
+ * Definition of a SET_CONFIG reply from DPOA.
+ */
+enum set_config_status {
+	SET_CONFIG_PENDING = 0,
+	SET_CONFIG_ACK_RECEIVED,
+	SET_CONFIG_RX_TIMEOUT,
+	SET_CONFIG_UNKNOWN_ERROR,
+};
+
+/**
+ * Definition of a set_config reply
+ */
+struct set_config_reply_control_data {
+	uint8_t instance; /* DPIA Instance */
+	uint8_t status; /* Set Config reply */
+	uint16_t pad; /* Alignment */
+};
+
+/**
+ * Definition of a DMUB_OUT_CMD__SET_CONFIG_REPLY command.
+ */
+struct dmub_rb_cmd_dp_set_config_reply {
+	struct dmub_cmd_header header;
+	struct set_config_reply_control_data set_config_reply_control;
+};
+
 /*
  * Command IDs should be treated as stable ABI.
  * Do not reuse or modify IDs.
@@ -2185,6 +2314,24 @@
 };
 
 /**
+ * Data passed in/out in a DMUB_CMD__VBIOS_TRANSMITTER_QUERY_DP_ALT command.
+ */
+struct dmub_rb_cmd_transmitter_query_dp_alt_data {
+	uint8_t phy_id; /**< 0=UNIPHYA, 1=UNIPHYB, 2=UNIPHYC, 3=UNIPHYD, 4=UNIPHYE, 5=UNIPHYF */
+	uint8_t is_usb; /**< is phy is usb */
+	uint8_t is_dp_alt_disable; /**< is dp alt disable */
+	uint8_t is_dp4; /**< is dp in 4 lane */
+};
+
+/**
+ * Definition of a DMUB_CMD__VBIOS_TRANSMITTER_QUERY_DP_ALT command.
+ */
+struct dmub_rb_cmd_transmitter_query_dp_alt {
+	struct dmub_cmd_header header; /**< header */
+	struct dmub_rb_cmd_transmitter_query_dp_alt_data data; /**< payload */
+};
+
+/**
  * Maximum number of bytes a chunk sent to DMUB for parsing
  */
 #define DMUB_EDID_CEA_DATA_CHUNK_BYTES 8
@@ -2383,6 +2530,22 @@
 	 */
 	struct dmub_rb_cmd_lvtma_control lvtma_control;
 	/**
+	 * Definition of a DMUB_CMD__VBIOS_TRANSMITTER_QUERY_DP_ALT command.
+	 */
+	struct dmub_rb_cmd_transmitter_query_dp_alt query_dp_alt;
+	/**
+	 * Definition of a DMUB_CMD__DPIA_DIG1_CONTROL command.
+	 */
+	struct dmub_rb_cmd_dig1_dpia_control dig1_dpia_control;
+	/**
+	 * Definition of a DMUB_CMD__DPIA_SET_CONFIG_ACCESS command.
+	 */
+	struct dmub_rb_cmd_set_config_access set_config_access;
+	/**
+	 * Definition of a DMUB_CMD__DPIA_MST_ALLOC_SLOTS command.
+	 */
+	struct dmub_rb_cmd_set_mst_alloc_slots set_mst_alloc_slots;
+	/**
 	 * Definition of a DMUB_CMD__EDID_CEA command.
 	 */
 	struct dmub_rb_cmd_edid_cea edid_cea;
@@ -2404,6 +2567,10 @@
 	 * HPD notify command.
 	 */
 	struct dmub_rb_cmd_dp_hpd_notify dp_hpd_notify;
+	/**
+	 * SET_CONFIG reply command.
+	 */
+	struct dmub_rb_cmd_dp_set_config_reply set_config_reply;
 };
 #pragma pack(pop)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dmub/src/dmub_dcn31.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dmub/src/dmub_dcn31.c
@@ -338,6 +338,10 @@
 	union dmub_fw_boot_options boot_options = {0};
 
 	boot_options.bits.z10_disable = params->disable_z10;
+	boot_options.bits.dpia_supported = params->dpia_supported;
+	boot_options.bits.enable_dpia = params->disable_dpia ? 0 : 1;
+
+	boot_options.bits.sel_mux_phy_c_d_phy_f_g = (dmub->asic == DMUB_ASIC_DCN31B) ? 1 : 0;
 
 	REG_WRITE(DMCUB_SCRATCH14, boot_options.all);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dmub/src/dmub_srv.c
@@ -208,6 +208,7 @@
 		break;
 
 	case DMUB_ASIC_DCN31:
+	case DMUB_ASIC_DCN31B:
 		dmub->regs_dcn31 = &dmub_srv_dcn31_regs;
 		funcs->reset = dmub_dcn31_reset;
 		funcs->reset_release = dmub_dcn31_reset_release;
@@ -318,7 +319,7 @@
 	uint32_t fw_state_size = DMUB_FW_STATE_SIZE;
 	uint32_t trace_buffer_size = DMUB_TRACE_BUFFER_SIZE;
 	uint32_t scratch_mem_size = DMUB_SCRATCH_MEM_SIZE;
-
+	uint32_t previous_top = 0;
 	if (!dmub->sw_init)
 		return DMUB_STATUS_INVALID;
 
@@ -343,8 +344,15 @@
 	bios->base = dmub_align(stack->top, 256);
 	bios->top = bios->base + params->vbios_size;
 
-	mail->base = dmub_align(bios->top, 256);
-	mail->top = mail->base + DMUB_MAILBOX_SIZE;
+	if (params->is_mailbox_in_inbox) {
+		mail->base = 0;
+		mail->top = mail->base + DMUB_MAILBOX_SIZE;
+		previous_top = bios->top;
+	} else {
+		mail->base = dmub_align(bios->top, 256);
+		mail->top = mail->base + DMUB_MAILBOX_SIZE;
+		previous_top = mail->top;
+	}
 
 	fw_info = dmub_get_fw_meta_info(params);
 
@@ -363,7 +371,7 @@
 			dmub->fw_version = fw_info->fw_version;
 	}
 
-	trace_buff->base = dmub_align(mail->top, 256);
+	trace_buff->base = dmub_align(previous_top, 256);
 	trace_buff->top = trace_buff->base + dmub_align(trace_buffer_size, 64);
 
 	fw_state->base = dmub_align(trace_buff->top, 256);
@@ -374,11 +382,14 @@
 
 	out->fb_size = dmub_align(scratch_mem->top, 4096);
 
+	if (params->is_mailbox_in_inbox)
+		out->inbox_size = dmub_align(mail->top, 4096);
+
 	return DMUB_STATUS_OK;
 }
 
-enum dmub_status dmub_srv_calc_fb_info(struct dmub_srv *dmub,
-				       const struct dmub_srv_fb_params *params,
+enum dmub_status dmub_srv_calc_mem_info(struct dmub_srv *dmub,
+				       const struct dmub_srv_memory_params *params,
 				       struct dmub_srv_fb_info *out)
 {
 	uint8_t *cpu_base;
@@ -393,8 +404,8 @@
 	if (params->region_info->num_regions != DMUB_NUM_WINDOWS)
 		return DMUB_STATUS_INVALID;
 
-	cpu_base = (uint8_t *)params->cpu_addr;
-	gpu_base = params->gpu_addr;
+	cpu_base = (uint8_t *)params->cpu_fb_addr;
+	gpu_base = params->gpu_fb_addr;
 
 	for (i = 0; i < DMUB_NUM_WINDOWS; ++i) {
 		const struct dmub_region *reg =
@@ -402,6 +413,12 @@
 
 		out->fb[i].cpu_addr = cpu_base + reg->base;
 		out->fb[i].gpu_addr = gpu_base + reg->base;
+
+		if (i == DMUB_WINDOW_4_MAILBOX && params->cpu_inbox_addr != 0) {
+			out->fb[i].cpu_addr = (uint8_t *)params->cpu_inbox_addr + reg->base;
+			out->fb[i].gpu_addr = params->gpu_inbox_addr + reg->base;
+		}
+
 		out->fb[i].size = reg->top - reg->base;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/dmub/src/dmub_srv_stat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/dmub/src/dmub_srv_stat.c
@@ -76,6 +76,22 @@
 		dmub_memcpy((void *)&notify->aux_reply,
 			(void *)&cmd.dp_aux_reply.reply_data, sizeof(struct aux_reply_data));
 		break;
+	case DMUB_OUT_CMD__DP_HPD_NOTIFY:
+		if (cmd.dp_hpd_notify.hpd_data.hpd_type == DP_HPD) {
+			notify->type = DMUB_NOTIFICATION_HPD;
+			notify->hpd_status = cmd.dp_hpd_notify.hpd_data.hpd_status;
+		} else {
+			notify->type = DMUB_NOTIFICATION_HPD_IRQ;
+		}
+
+		notify->link_index = cmd.dp_hpd_notify.hpd_data.instance;
+		notify->result = AUX_RET_SUCCESS;
+		break;
+	case DMUB_OUT_CMD__SET_CONFIG_REPLY:
+		notify->type = DMUB_NOTIFICATION_SET_CONFIG_REPLY;
+		notify->link_index = cmd.set_config_reply.set_config_reply_control.instance;
+		notify->sc_status = cmd.set_config_reply.set_config_reply_control.status;
+		break;
 	default:
 		notify->type = DMUB_NOTIFICATION_NO_DATA;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/include/dpcd_defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/include/dpcd_defs.h
@@ -149,6 +149,7 @@
 	PSR_SINK_STATE_SINK_INTERNAL_ERROR = 7,
 };
 
+#define DP_SOURCE_SEQUENCE    		    0x30c
 #define DP_SOURCE_TABLE_REVISION	    0x310
 #define DP_SOURCE_PAYLOAD_SIZE		    0x311
 #define DP_SOURCE_SINK_CAP		    0x317
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/include/link_service_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/include/link_service_types.h
@@ -152,6 +152,22 @@
 	DP_PANEL_MODE_SPECIAL
 };
 
+enum dpcd_source_sequence {
+	DPCD_SOURCE_SEQ_AFTER_CONNECT_DIG_FE_OTG = 1, /*done in apply_single_controller_ctx_to_hw */
+	DPCD_SOURCE_SEQ_AFTER_DP_STREAM_ATTR,         /*done in core_link_enable_stream */
+	DPCD_SOURCE_SEQ_AFTER_UPDATE_INFO_FRAME,      /*done in core_link_enable_stream/dcn20_enable_stream */
+	DPCD_SOURCE_SEQ_AFTER_CONNECT_DIG_FE_BE,      /*done in perform_link_training_with_retries/dcn20_enable_stream */
+	DPCD_SOURCE_SEQ_AFTER_ENABLE_LINK_PHY,        /*done in dp_enable_link_phy */
+	DPCD_SOURCE_SEQ_AFTER_SET_SOURCE_PATTERN,     /*done in dp_set_hw_test_pattern */
+	DPCD_SOURCE_SEQ_AFTER_ENABLE_AUDIO_STREAM,    /*done in dce110_enable_audio_stream */
+	DPCD_SOURCE_SEQ_AFTER_ENABLE_DP_VID_STREAM,   /*done in enc1_stream_encoder_dp_unblank */
+	DPCD_SOURCE_SEQ_AFTER_DISABLE_DP_VID_STREAM,  /*done in enc1_stream_encoder_dp_blank */
+	DPCD_SOURCE_SEQ_AFTER_FIFO_STEER_RESET,       /*done in enc1_stream_encoder_dp_blank */
+	DPCD_SOURCE_SEQ_AFTER_DISABLE_AUDIO_STREAM,   /*done in dce110_disable_audio_stream */
+	DPCD_SOURCE_SEQ_AFTER_DISABLE_LINK_PHY,       /*done in dp_disable_link_phy */
+	DPCD_SOURCE_SEQ_AFTER_DISCONNECT_DIG_FE_BE,   /*done in dce110_disable_stream */
+};
+
 /* DPCD_ADDR_TRAINING_LANEx_SET registers value */
 union dpcd_training_lane_set {
 	struct {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/include/logger_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/include/logger_types.h
@@ -72,6 +72,9 @@
 #define DC_LOG_DSC(...) DRM_DEBUG_KMS(__VA_ARGS__)
 #define DC_LOG_SMU(...) pr_debug("[SMU_MSG]:"__VA_ARGS__)
 #define DC_LOG_DWB(...) DRM_DEBUG_KMS(__VA_ARGS__)
+#if defined(CONFIG_DRM_AMD_DC_DCN)
+#define DC_LOG_DP2(...) DRM_DEBUG_KMS(__VA_ARGS__)
+#endif
 
 struct dal_logger;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/color/color_gamma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/color/color_gamma.c
@@ -1597,6 +1597,7 @@
 	struct fixed31_32 lut2;
 	struct fixed31_32 delta_lut;
 	struct fixed31_32 delta_index;
+	const struct fixed31_32 one = dc_fixpt_from_int(1);
 
 	i = 0;
 	/* fixed_pt library has problems handling too small values */
@@ -1625,6 +1626,9 @@
 			} else
 				hw_x = coordinates_x[i].x;
 
+			if (dc_fixpt_le(one, hw_x))
+				hw_x = one;
+
 			norm_x = dc_fixpt_mul(norm_factor, hw_x);
 			index = dc_fixpt_floor(norm_x);
 			if (index < 0 || index > 255)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/freesync/freesync.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/freesync/freesync.c
@@ -131,7 +131,7 @@
 
 	v_total = div64_u64(div64_u64(((unsigned long long)(
 			frame_duration_in_ns) * (stream->timing.pix_clk_100hz / 10)),
-			stream->timing.h_total), 1000000);
+			stream->timing.h_total) + 500000, 1000000);
 
 	/* v_total cannot be less than nominal */
 	if (v_total < stream->timing.v_total) {
@@ -327,7 +327,9 @@
 		 *  - Delta for CEIL: delta_from_mid_point_in_us_1
 		 *  - Delta for FLOOR: delta_from_mid_point_in_us_2
 		 */
-		if ((last_render_time_in_us / mid_point_frames_ceil) < in_out_vrr->min_duration_in_us) {
+		if (mid_point_frames_ceil &&
+		    (last_render_time_in_us / mid_point_frames_ceil) <
+		    in_out_vrr->min_duration_in_us) {
 			/* Check for out of range.
 			 * If using CEIL produces a value that is out of range,
 			 * then we are forced to use FLOOR.
@@ -374,8 +376,9 @@
 		/* Either we've calculated the number of frames to insert,
 		 * or we need to insert min duration frames
 		 */
-		if (last_render_time_in_us / frames_to_insert <
-				in_out_vrr->min_duration_in_us){
+		if (frames_to_insert &&
+		    (last_render_time_in_us / frames_to_insert) <
+		    in_out_vrr->min_duration_in_us){
 			frames_to_insert -= (frames_to_insert > 1) ?
 					1 : 0;
 		}
@@ -567,10 +570,6 @@
 	 * Note: We should never go above the field rate of the mode timing set.
 	 */
 	infopacket->sb[8] = (unsigned char)((vrr->max_refresh_in_uhz + 500000) / 1000000);
-
-	/* FreeSync HDR */
-	infopacket->sb[9] = 0;
-	infopacket->sb[10] = 0;
 }
 
 static void build_vrr_infopacket_data_v3(const struct mod_vrr_params *vrr,
@@ -638,10 +637,6 @@
 
 	/* PB16 : Reserved bits 7:1, FixedRate bit 0 */
 	infopacket->sb[16] = (vrr->state == VRR_STATE_ACTIVE_FIXED) ? 1 : 0;
-
-	//FreeSync HDR
-	infopacket->sb[9] = 0;
-	infopacket->sb[10] = 0;
 }
 
 static void build_vrr_infopacket_fs2_data(enum color_transfer_func app_tf,
@@ -726,8 +721,7 @@
 		/* HB2  = [Bits 7:5 = 0] [Bits 4:0 = Length = 0x09] */
 		infopacket->hb2 = 0x09;
 
-		*payload_size = 0x0A;
-
+		*payload_size = 0x09;
 	} else if (dc_is_dp_signal(signal)) {
 
 		/* HEADER */
@@ -776,9 +770,9 @@
 		infopacket->hb1 = version;
 
 		/* HB2  = [Bits 7:5 = 0] [Bits 4:0 = Length] */
-		*payload_size = 0x10;
-		infopacket->hb2 = *payload_size - 1; //-1 for checksum
+		infopacket->hb2 = 0x10;
 
+		*payload_size = 0x10;
 	} else if (dc_is_dp_signal(signal)) {
 
 		/* HEADER */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/hdcp/hdcp1_execution.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/hdcp/hdcp1_execution.c
@@ -433,17 +433,20 @@
 	}
 
 	if (status == MOD_HDCP_STATUS_SUCCESS)
-		mod_hdcp_execute_and_set(mod_hdcp_read_bstatus,
+		if (!mod_hdcp_execute_and_set(mod_hdcp_read_bstatus,
 				&input->bstatus_read, &status,
-				hdcp, "bstatus_read");
+				hdcp, "bstatus_read"))
+			goto out;
 	if (status == MOD_HDCP_STATUS_SUCCESS)
-		mod_hdcp_execute_and_set(check_link_integrity_dp,
+		if (!mod_hdcp_execute_and_set(check_link_integrity_dp,
 				&input->link_integrity_check, &status,
-				hdcp, "link_integrity_check");
+				hdcp, "link_integrity_check"))
+			goto out;
 	if (status == MOD_HDCP_STATUS_SUCCESS)
-		mod_hdcp_execute_and_set(check_no_reauthentication_request_dp,
+		if (!mod_hdcp_execute_and_set(check_no_reauthentication_request_dp,
 				&input->reauth_request_check, &status,
-				hdcp, "reauth_request_check");
+				hdcp, "reauth_request_check"))
+			goto out;
 out:
 	return status;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c
@@ -156,7 +156,16 @@
 	uint32_t cur_size = 0;
 	uint32_t data_offset = 0;
 
+	if (msg_id == MOD_HDCP_MESSAGE_ID_INVALID ||
+		msg_id >= MOD_HDCP_MESSAGE_ID_MAX)
+		return MOD_HDCP_STATUS_DDC_FAILURE;
+
 	if (is_dp_hdcp(hdcp)) {
+		int num_dpcd_addrs = sizeof(hdcp_dpcd_addrs) /
+			sizeof(hdcp_dpcd_addrs[0]);
+		if (msg_id >= num_dpcd_addrs)
+			return MOD_HDCP_STATUS_DDC_FAILURE;
+
 		while (buf_len > 0) {
 			cur_size = MIN(buf_len, HDCP_MAX_AUX_TRANSACTION_SIZE);
 			success = hdcp->config.ddc.funcs.read_dpcd(hdcp->config.ddc.handle,
@@ -171,6 +180,11 @@
 			data_offset += cur_size;
 		}
 	} else {
+		int num_i2c_offsets = sizeof(hdcp_i2c_offsets) /
+			sizeof(hdcp_i2c_offsets[0]);
+		if (msg_id >= num_i2c_offsets)
+			return MOD_HDCP_STATUS_DDC_FAILURE;
+
 		success = hdcp->config.ddc.funcs.read_i2c(
 				hdcp->config.ddc.handle,
 				HDCP_I2C_ADDR,
@@ -215,7 +229,16 @@
 	uint32_t cur_size = 0;
 	uint32_t data_offset = 0;
 
+	if (msg_id == MOD_HDCP_MESSAGE_ID_INVALID ||
+		msg_id >= MOD_HDCP_MESSAGE_ID_MAX)
+		return MOD_HDCP_STATUS_DDC_FAILURE;
+
 	if (is_dp_hdcp(hdcp)) {
+		int num_dpcd_addrs = sizeof(hdcp_dpcd_addrs) /
+			sizeof(hdcp_dpcd_addrs[0]);
+		if (msg_id >= num_dpcd_addrs)
+			return MOD_HDCP_STATUS_DDC_FAILURE;
+
 		while (buf_len > 0) {
 			cur_size = MIN(buf_len, HDCP_MAX_AUX_TRANSACTION_SIZE);
 			success = hdcp->config.ddc.funcs.write_dpcd(
@@ -231,6 +254,11 @@
 			data_offset += cur_size;
 		}
 	} else {
+		int num_i2c_offsets = sizeof(hdcp_i2c_offsets) /
+			sizeof(hdcp_i2c_offsets[0]);
+		if (msg_id >= num_i2c_offsets)
+			return MOD_HDCP_STATUS_DDC_FAILURE;
+
 		hdcp->buf[0] = hdcp_i2c_offsets[msg_id];
 		memmove(&hdcp->buf[1], buf, buf_len);
 		success = hdcp->config.ddc.funcs.write_i2c(
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/hdcp/hdcp_psp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/hdcp/hdcp_psp.c
@@ -509,6 +509,9 @@
 	hdcp_cmd = (struct ta_hdcp_shared_memory *)psp->hdcp_context.context.mem_context.shared_buf;
 	memset(hdcp_cmd, 0, sizeof(struct ta_hdcp_shared_memory));
 
+	if (!display)
+		return MOD_HDCP_STATUS_DISPLAY_NOT_FOUND;
+
 	hdcp_cmd->in_msg.hdcp2_create_session_v2.display_handle = display->index;
 
 	if (hdcp->connection.link.adjust.hdcp2.force_type == MOD_HDCP_FORCE_TYPE_0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/inc/mod_stats.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/inc/mod_stats.h
@@ -57,10 +57,10 @@
 		unsigned int length);
 
 void mod_stats_update_flip(struct mod_stats *mod_stats,
-		unsigned long timestamp_in_ns);
+		unsigned long long timestamp_in_ns);
 
 void mod_stats_update_vupdate(struct mod_stats *mod_stats,
-		unsigned long timestamp_in_ns);
+		unsigned long long timestamp_in_ns);
 
 void mod_stats_update_freesync(struct mod_stats *mod_stats,
 		unsigned int v_total_min,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/display/modules/info_packet/info_packet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/display/modules/info_packet/info_packet.c
@@ -100,7 +100,8 @@
 //PB7 = MD0
 #define MASK_VTEM_MD0__VRR_EN         0x01
 #define MASK_VTEM_MD0__M_CONST        0x02
-#define MASK_VTEM_MD0__RESERVED2      0x0C
+#define MASK_VTEM_MD0__QMS_EN         0x04
+#define MASK_VTEM_MD0__RESERVED2      0x08
 #define MASK_VTEM_MD0__FVA_FACTOR_M1  0xF0
 
 //MD1
@@ -109,7 +110,7 @@
 //MD2
 #define MASK_VTEM_MD2__BASE_REFRESH_RATE_98  0x03
 #define MASK_VTEM_MD2__RB                    0x04
-#define MASK_VTEM_MD2__RESERVED3             0xF8
+#define MASK_VTEM_MD2__NEXT_TFR              0xF8
 
 //MD3
 #define MASK_VTEM_MD3__BASE_REFRESH_RATE_07  0xFF
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/include/amd_shared.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/include/amd_shared.h
@@ -98,7 +98,8 @@
 	AMD_IP_BLOCK_TYPE_ACP,
 	AMD_IP_BLOCK_TYPE_VCN,
 	AMD_IP_BLOCK_TYPE_MES,
-	AMD_IP_BLOCK_TYPE_JPEG
+	AMD_IP_BLOCK_TYPE_JPEG,
+	AMD_IP_BLOCK_TYPE_NUM,
 };
 
 enum amd_clockgating_state {
@@ -228,7 +229,7 @@
 	DC_FBC_MASK = (1 << 0), //0x1, disabled by default
 	DC_MULTI_MON_PP_MCLK_SWITCH_MASK = (1 << 1), //0x2, enabled by default
 	DC_DISABLE_FRACTIONAL_PWM_MASK = (1 << 2), //0x4, disabled by default
-	DC_PSR_MASK = (1 << 3), //0x8, disabled by default
+	DC_PSR_MASK = (1 << 3), //0x8, disabled by default for dcn < 3.1
 	DC_EDP_NO_POWER_SEQUENCING = (1 << 4), //0x10, disabled by default
 };
 
@@ -236,7 +237,8 @@
 	DC_DISABLE_PIPE_SPLIT = 0x1,
 	DC_DISABLE_STUTTER = 0x2,
 	DC_DISABLE_DSC = 0x4,
-	DC_DISABLE_CLOCK_GATING = 0x8
+	DC_DISABLE_CLOCK_GATING = 0x8,
+	DC_DISABLE_PSR = 0x10,
 };
 
 enum amd_dpm_forced_level;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/include/atombios.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/include/atombios.h
@@ -4107,7 +4107,7 @@
 {
   UCHAR ucRecordType;
   UCHAR ucFakeEDIDLength;       // = 128 means EDID length is 128 bytes, otherwise the EDID length = ucFakeEDIDLength*128
-  UCHAR ucFakeEDIDString[1];    // This actually has ucFakeEdidLength elements.
+  UCHAR ucFakeEDIDString[];     // This actually has ucFakeEdidLength elements.
 } ATOM_FAKE_EDID_PATCH_RECORD;
 
 typedef struct  _ATOM_PANEL_RESOLUTION_PATCH_RECORD
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/include/atomfirmware.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/include/atomfirmware.h
@@ -701,7 +701,7 @@
 {
   struct  atom_common_table_header  table_header;
   /*the real number of this included in the structure is calcualted by using the (whole structure size - the header size)/size of atom_gpio_pin_lut  */
-  struct  atom_gpio_pin_assignment  gpio_pin[8];
+  struct  atom_gpio_pin_assignment  gpio_pin[];
 };
 
 
@@ -1467,6 +1467,49 @@
 	uint32_t  reserved4[189];
 };
 
+struct uma_carveout_option {
+  char       optionName[29];        //max length of string is 28chars + '\0'. Current design is for "minimum", "Medium", "High". This makes entire struct size 64bits
+  uint8_t    memoryCarvedGb;        //memory carved out with setting
+  uint8_t    memoryRemainingGb;     //memory remaining on system
+  union {
+    struct _flags {
+      uint8_t Auto     : 1;
+      uint8_t Custom   : 1;
+      uint8_t Reserved : 6;
+    } flags;
+    uint8_t all8;
+  } uma_carveout_option_flags;
+};
+
+struct atom_integrated_system_info_v2_3 {
+  struct  atom_common_table_header table_header;
+  uint32_t  vbios_misc; // enum of atom_system_vbiosmisc_def
+  uint32_t  gpucapinfo; // enum of atom_system_gpucapinf_def
+  uint32_t  system_config;
+  uint32_t  cpucapinfo;
+  uint16_t  gpuclk_ss_percentage; // unit of 0.001%,   1000 mean 1%
+  uint16_t  gpuclk_ss_type;
+  uint16_t  dpphy_override;  // bit vector, enum of atom_sysinfo_dpphy_override_def
+  uint8_t memorytype;       // enum of atom_dmi_t17_mem_type_def, APU memory type indication.
+  uint8_t umachannelnumber; // number of memory channels
+  uint8_t htc_hyst_limit;
+  uint8_t htc_tmp_limit;
+  uint8_t reserved1; // dp_ss_control
+  uint8_t gpu_package_id;
+  struct  edp_info_table  edp1_info;
+  struct  edp_info_table  edp2_info;
+  uint32_t  reserved2[8];
+  struct  atom_external_display_connection_info extdispconninfo;
+  uint8_t UMACarveoutVersion;
+  uint8_t UMACarveoutIndexMax;
+  uint8_t UMACarveoutTypeDefault;
+  uint8_t UMACarveoutIndexDefault;
+  uint8_t UMACarveoutType;           //Auto or Custom
+  uint8_t UMACarveoutIndex;
+  struct  uma_carveout_option UMASizeControlOption[20];
+  uint8_t reserved3[110];
+};
+
 // system_config
 enum atom_system_vbiosmisc_def{
   INTEGRATED_SYSTEM_INFO__GET_EDID_CALLBACK_FUNC_SUPPORT = 0x01,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/include/discovery.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/include/discovery.h
@@ -143,6 +143,55 @@
 	uint32_t gc_num_gl2a;
 };
 
+struct gc_info_v1_1 {
+	struct gpu_info_header header;
+
+	uint32_t gc_num_se;
+	uint32_t gc_num_wgp0_per_sa;
+	uint32_t gc_num_wgp1_per_sa;
+	uint32_t gc_num_rb_per_se;
+	uint32_t gc_num_gl2c;
+	uint32_t gc_num_gprs;
+	uint32_t gc_num_max_gs_thds;
+	uint32_t gc_gs_table_depth;
+	uint32_t gc_gsprim_buff_depth;
+	uint32_t gc_parameter_cache_depth;
+	uint32_t gc_double_offchip_lds_buffer;
+	uint32_t gc_wave_size;
+	uint32_t gc_max_waves_per_simd;
+	uint32_t gc_max_scratch_slots_per_cu;
+	uint32_t gc_lds_size;
+	uint32_t gc_num_sc_per_se;
+	uint32_t gc_num_sa_per_se;
+	uint32_t gc_num_packer_per_sc;
+	uint32_t gc_num_gl2a;
+	uint32_t gc_num_tcp_per_sa;
+	uint32_t gc_num_sdp_interface;
+	uint32_t gc_num_tcps;
+};
+
+struct gc_info_v2_0 {
+	struct gpu_info_header header;
+
+	uint32_t gc_num_se;
+	uint32_t gc_num_cu_per_sh;
+	uint32_t gc_num_sh_per_se;
+	uint32_t gc_num_rb_per_se;
+	uint32_t gc_num_tccs;
+	uint32_t gc_num_gprs;
+	uint32_t gc_num_max_gs_thds;
+	uint32_t gc_gs_table_depth;
+	uint32_t gc_gsprim_buff_depth;
+	uint32_t gc_parameter_cache_depth;
+	uint32_t gc_double_offchip_lds_buffer;
+	uint32_t gc_wave_size;
+	uint32_t gc_max_waves_per_simd;
+	uint32_t gc_max_scratch_slots_per_cu;
+	uint32_t gc_lds_size;
+	uint32_t gc_num_sc_per_se;
+	uint32_t gc_num_packer_per_sc;
+};
+
 typedef struct harvest_info_header {
 	uint32_t signature; /* Table Signature */
 	uint32_t version;   /* Table Version */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/include/kgd_pp_interface.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/include/kgd_pp_interface.h
@@ -341,7 +341,8 @@
 	int (*get_power_profile_mode)(void *handle, char *buf);
 	int (*set_power_profile_mode)(void *handle, long *input, uint32_t size);
 	int (*set_fine_grain_clk_vol)(void *handle, uint32_t type, long *input, uint32_t size);
-	int (*odn_edit_dpm_table)(void *handle, uint32_t type, long *input, uint32_t size);
+	int (*odn_edit_dpm_table)(void *handle, enum PP_OD_DPM_TABLE_COMMAND type,
+				  long *input, uint32_t size);
 	int (*set_mp1_state)(void *handle, enum pp_mp1_state mp1_state);
 	int (*smu_i2c_bus_access)(void *handle, bool acquire);
 	int (*gfx_state_change_set)(void *handle, uint32_t state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/include/pptable.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/include/pptable.h
@@ -78,7 +78,7 @@
 typedef struct _ATOM_PPLIB_STATE
 {
     UCHAR ucNonClockStateIndex;
-    UCHAR ucClockStateIndices[1]; // variable-sized
+    UCHAR ucClockStateIndices[]; // variable-sized
 } ATOM_PPLIB_STATE;
 
 
@@ -473,7 +473,7 @@
       /**
       * Driver will read the first ucNumDPMLevels in this array
       */
-      UCHAR clockInfoIndex[1];
+      UCHAR clockInfoIndex[];
 } ATOM_PPLIB_STATE_V2;
 
 typedef struct _StateArray{
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/amdgpu_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/amdgpu_dpm.c
@@ -188,29 +188,6 @@
 	return vrefresh;
 }
 
-bool amdgpu_is_internal_thermal_sensor(enum amdgpu_int_thermal_type sensor)
-{
-	switch (sensor) {
-	case THERMAL_TYPE_RV6XX:
-	case THERMAL_TYPE_RV770:
-	case THERMAL_TYPE_EVERGREEN:
-	case THERMAL_TYPE_SUMO:
-	case THERMAL_TYPE_NI:
-	case THERMAL_TYPE_SI:
-	case THERMAL_TYPE_CI:
-	case THERMAL_TYPE_KV:
-		return true;
-	case THERMAL_TYPE_ADT7473_WITH_INTERNAL:
-	case THERMAL_TYPE_EMC2103_WITH_INTERNAL:
-		return false; /* need special handling */
-	case THERMAL_TYPE_NONE:
-	case THERMAL_TYPE_EXTERNAL:
-	case THERMAL_TYPE_EXTERNAL_GPIO:
-	default:
-		return false;
-	}
-}
-
 union power_info {
 	struct _ATOM_POWERPLAY_INFO info;
 	struct _ATOM_POWERPLAY_INFO_V2 info_2;
@@ -927,6 +904,13 @@
 {
 	int ret = 0;
 	const struct amd_pm_funcs *pp_funcs = adev->powerplay.pp_funcs;
+	enum ip_power_state pwr_state = gate ? POWER_STATE_OFF : POWER_STATE_ON;
+
+	if (atomic_read(&adev->pm.pwr_state[block_type]) == pwr_state) {
+		dev_dbg(adev->dev, "IP block%d already in the target %s state!",
+				block_type, gate ? "gate" : "ungate");
+		return 0;
+	}
 
 	switch (block_type) {
 	case AMD_IP_BLOCK_TYPE_UVD:
@@ -979,6 +963,9 @@
 		break;
 	}
 
+	if (!ret)
+		atomic_set(&adev->pm.pwr_state[block_type], pwr_state);
+
 	return ret;
 }
 
@@ -1035,6 +1022,17 @@
 
 	if (!pp_funcs || !pp_funcs->get_asic_baco_capability)
 		return false;
+	/* Don't use baco for reset in S3.
+	 * This is a workaround for some platforms
+	 * where entering BACO during suspend
+	 * seems to cause reboots or hangs.
+	 * This might be related to the fact that BACO controls
+	 * power to the whole GPU including devices like audio and USB.
+	 * Powering down/up everything may adversely affect these other
+	 * devices.  Needs more investigation.
+	 */
+	if (adev->in_s3)
+		return false;
 
 	if (pp_funcs->get_asic_baco_capability(pp_handle, &baco_cap))
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/amdgpu_pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/amdgpu_pm.c
@@ -807,7 +807,7 @@
 	if (adev->in_suspend && !adev->in_runpm)
 		return -EPERM;
 
-	if (count > 127)
+	if (count > 127 || count == 0)
 		return -EINVAL;
 
 	if (*buf == 's')
@@ -827,7 +827,8 @@
 	else
 		return -EINVAL;
 
-	memcpy(buf_cpy, buf, count+1);
+	memcpy(buf_cpy, buf, count);
+	buf_cpy[count] = 0;
 
 	tmp_str = buf_cpy;
 
@@ -844,6 +845,9 @@
 			return -EINVAL;
 		parameter_size++;
 
+		if (!tmp_str)
+			break;
+
 		while (isspace(*tmp_str))
 			tmp_str++;
 	}
@@ -2117,6 +2121,12 @@
 		}
 	}
 
+	/* setting should not be allowed from VF if not in one VF mode */
+	if (amdgpu_sriov_vf(adev) && !amdgpu_sriov_is_pp_one_vf(adev)) {
+		dev_attr->attr.mode &= ~S_IWUGO;
+		dev_attr->store = NULL;
+	}
+
 #undef DEVICE_ATTR_IS
 
 	return 0;
@@ -2128,15 +2138,19 @@
 				     uint32_t mask, struct list_head *attr_list)
 {
 	int ret = 0;
-	struct device_attribute *dev_attr = &attr->dev_attr;
-	const char *name = dev_attr->attr.name;
 	enum amdgpu_device_attr_states attr_states = ATTR_STATE_SUPPORTED;
 	struct amdgpu_device_attr_entry *attr_entry;
+	struct device_attribute *dev_attr;
+	const char *name;
 
 	int (*attr_update)(struct amdgpu_device *adev, struct amdgpu_device_attr *attr,
 			   uint32_t mask, enum amdgpu_device_attr_states *states) = default_attr_update;
 
-	BUG_ON(!attr);
+	if (!attr)
+		return -EINVAL;
+
+	dev_attr = &attr->dev_attr;
+	name = dev_attr->attr.name;
 
 	attr_update = attr->attr_update ? attr->attr_update : default_attr_update;
 
@@ -3439,8 +3453,7 @@
 	     attr == &sensor_dev_attr_power2_cap_min.dev_attr.attr ||
 		 attr == &sensor_dev_attr_power2_cap.dev_attr.attr ||
 		 attr == &sensor_dev_attr_power2_cap_default.dev_attr.attr ||
-		 attr == &sensor_dev_attr_power2_label.dev_attr.attr ||
-		 attr == &sensor_dev_attr_power1_label.dev_attr.attr))
+		 attr == &sensor_dev_attr_power2_label.dev_attr.attr))
 		return 0;
 
 	return effective_mode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/inc/amdgpu_dpm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/inc/amdgpu_dpm.h
@@ -417,6 +417,12 @@
 	enum amd_dpm_forced_level forced_level;
 };
 
+enum ip_power_state {
+	POWER_STATE_UNKNOWN,
+	POWER_STATE_ON,
+	POWER_STATE_OFF,
+};
+
 struct amdgpu_pm {
 	struct mutex		mutex;
 	u32                     current_sclk;
@@ -452,6 +458,8 @@
 	struct i2c_adapter smu_i2c;
 	struct mutex		smu_i2c_mutex;
 	struct list_head	pm_attr_list;
+
+	atomic_t		pwr_state[AMD_IP_BLOCK_TYPE_NUM];
 };
 
 #define R600_SSTU_DFLT                               0
@@ -493,8 +501,6 @@
 int amdgpu_dpm_read_sensor(struct amdgpu_device *adev, enum amd_pp_sensors sensor,
 			   void *data, uint32_t *size);
 
-bool amdgpu_is_internal_thermal_sensor(enum amdgpu_int_thermal_type sensor);
-
 int amdgpu_get_platform_caps(struct amdgpu_device *adev);
 
 int amdgpu_parse_extended_power_table(struct amdgpu_device *adev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c
@@ -924,7 +924,8 @@
 	return hwmgr->hwmgr_func->set_fine_grain_clk_vol(hwmgr, type, input, size);
 }
 
-static int pp_odn_edit_dpm_table(void *handle, uint32_t type, long *input, uint32_t size)
+static int pp_odn_edit_dpm_table(void *handle, enum PP_OD_DPM_TABLE_COMMAND type,
+				 long *input, uint32_t size)
 {
 	struct pp_hwmgr *hwmgr = handle;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/pp_psm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/pp_psm.c
@@ -30,9 +30,8 @@
 {
 	int result;
 	unsigned int i;
-	unsigned int table_entries;
 	struct pp_power_state *state;
-	int size;
+	int size, table_entries;
 
 	if (hwmgr->hwmgr_func->get_num_of_pp_table_entries == NULL)
 		return 0;
@@ -40,15 +39,19 @@
 	if (hwmgr->hwmgr_func->get_power_state_size == NULL)
 		return 0;
 
-	hwmgr->num_ps = table_entries = hwmgr->hwmgr_func->get_num_of_pp_table_entries(hwmgr);
+	table_entries = hwmgr->hwmgr_func->get_num_of_pp_table_entries(hwmgr);
 
-	hwmgr->ps_size = size = hwmgr->hwmgr_func->get_power_state_size(hwmgr) +
+	size = hwmgr->hwmgr_func->get_power_state_size(hwmgr) +
 					  sizeof(struct pp_power_state);
 
-	if (table_entries == 0 || size == 0) {
+	if (table_entries <= 0 || size == 0) {
 		pr_warn("Please check whether power state management is supported on this asic\n");
+		hwmgr->num_ps = 0;
+		hwmgr->ps_size = 0;
 		return 0;
 	}
+	hwmgr->num_ps = table_entries;
+	hwmgr->ps_size = size;
 
 	hwmgr->ps = kcalloc(table_entries, size, GFP_KERNEL);
 	if (hwmgr->ps == NULL)
@@ -75,8 +78,10 @@
 	for (i = 0; i < table_entries; i++) {
 		result = hwmgr->hwmgr_func->get_pp_table_entry(hwmgr, i, state);
 		if (result) {
+			kfree(hwmgr->current_ps);
 			kfree(hwmgr->request_ps);
 			kfree(hwmgr->ps);
+			hwmgr->current_ps = NULL;
 			hwmgr->request_ps = NULL;
 			hwmgr->ps = NULL;
 			return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/ppatomctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/ppatomctrl.c
@@ -73,8 +73,9 @@
 					j++;
 				} else if ((table->mc_reg_address[i].uc_pre_reg_data &
 							LOW_NIBBLE_MASK) == DATA_EQU_PREV) {
-					table->mc_reg_table_entry[num_ranges].mc_data[i] =
-						table->mc_reg_table_entry[num_ranges].mc_data[i-1];
+					if (i)
+						table->mc_reg_table_entry[num_ranges].mc_data[i] =
+							table->mc_reg_table_entry[num_ranges].mc_data[i-1];
 				}
 			}
 			num_ranges++;
@@ -1419,6 +1420,8 @@
 			GetIndexIntoMasterTable(DATA, SMU_Info),
 			&size, &frev, &crev);
 
+	if (!psmu_info)
+		return -EINVAL;
 
 	for (i = 0; i < psmu_info->ucSclkEntryNum; i++) {
 		table->entry[i].ucVco_setting = psmu_info->asSclkFcwRangeEntry[i].ucVco_setting;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/pptable_v1_0.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/pptable_v1_0.h
@@ -164,7 +164,7 @@
 typedef struct _ATOM_Tonga_State_Array {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries;		/* Number of entries. */
-	ATOM_Tonga_State entries[1];	/* Dynamically allocate entries. */
+	ATOM_Tonga_State entries[];	/* Dynamically allocate entries. */
 } ATOM_Tonga_State_Array;
 
 typedef struct _ATOM_Tonga_MCLK_Dependency_Record {
@@ -179,7 +179,7 @@
 typedef struct _ATOM_Tonga_MCLK_Dependency_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries; 										/* Number of entries. */
-	ATOM_Tonga_MCLK_Dependency_Record entries[1];				/* Dynamically allocate entries. */
+	ATOM_Tonga_MCLK_Dependency_Record entries[];				/* Dynamically allocate entries. */
 } ATOM_Tonga_MCLK_Dependency_Table;
 
 typedef struct _ATOM_Tonga_SCLK_Dependency_Record {
@@ -194,7 +194,7 @@
 typedef struct _ATOM_Tonga_SCLK_Dependency_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries; 										/* Number of entries. */
-	ATOM_Tonga_SCLK_Dependency_Record entries[1];				 /* Dynamically allocate entries. */
+	ATOM_Tonga_SCLK_Dependency_Record entries[];				 /* Dynamically allocate entries. */
 } ATOM_Tonga_SCLK_Dependency_Table;
 
 typedef struct _ATOM_Polaris_SCLK_Dependency_Record {
@@ -210,7 +210,7 @@
 typedef struct _ATOM_Polaris_SCLK_Dependency_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries;							/* Number of entries. */
-	ATOM_Polaris_SCLK_Dependency_Record entries[1];				 /* Dynamically allocate entries. */
+	ATOM_Polaris_SCLK_Dependency_Record entries[];				 /* Dynamically allocate entries. */
 } ATOM_Polaris_SCLK_Dependency_Table;
 
 typedef struct _ATOM_Tonga_PCIE_Record {
@@ -222,7 +222,7 @@
 typedef struct _ATOM_Tonga_PCIE_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries; 										/* Number of entries. */
-	ATOM_Tonga_PCIE_Record entries[1];							/* Dynamically allocate entries. */
+	ATOM_Tonga_PCIE_Record entries[];							/* Dynamically allocate entries. */
 } ATOM_Tonga_PCIE_Table;
 
 typedef struct _ATOM_Polaris10_PCIE_Record {
@@ -235,7 +235,7 @@
 typedef struct _ATOM_Polaris10_PCIE_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries;                                         /* Number of entries. */
-	ATOM_Polaris10_PCIE_Record entries[1];                      /* Dynamically allocate entries. */
+	ATOM_Polaris10_PCIE_Record entries[];                      /* Dynamically allocate entries. */
 } ATOM_Polaris10_PCIE_Table;
 
 
@@ -252,7 +252,7 @@
 typedef struct _ATOM_Tonga_MM_Dependency_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries; 										/* Number of entries. */
-	ATOM_Tonga_MM_Dependency_Record entries[1]; 			   /* Dynamically allocate entries. */
+	ATOM_Tonga_MM_Dependency_Record entries[]; 			   /* Dynamically allocate entries. */
 } ATOM_Tonga_MM_Dependency_Table;
 
 typedef struct _ATOM_Tonga_Voltage_Lookup_Record {
@@ -265,7 +265,7 @@
 typedef struct _ATOM_Tonga_Voltage_Lookup_Table {
 	UCHAR ucRevId;
 	UCHAR ucNumEntries; 										/* Number of entries. */
-	ATOM_Tonga_Voltage_Lookup_Record entries[1];				/* Dynamically allocate entries. */
+	ATOM_Tonga_Voltage_Lookup_Record entries[];				/* Dynamically allocate entries. */
 } ATOM_Tonga_Voltage_Lookup_Table;
 
 typedef struct _ATOM_Tonga_Fan_Table {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/process_pptables_v1_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/process_pptables_v1_0.c
@@ -200,7 +200,7 @@
 		struct pp_hwmgr *hwmgr,
 		ATOM_Tonga_PPM_Table *atom_ppm_table)
 {
-	struct phm_ppm_table *ptr = kzalloc(sizeof(ATOM_Tonga_PPM_Table), GFP_KERNEL);
+	struct phm_ppm_table *ptr = kzalloc(sizeof(*ptr), GFP_KERNEL);
 	struct phm_ppt_v1_information *pp_table_information =
 		(struct phm_ppt_v1_information *)(hwmgr->pptable);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/processpptables.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/processpptables.c
@@ -1185,6 +1185,8 @@
 	fw_info = smu_atom_get_data_table(hwmgr->adev,
 			 GetIndexIntoMasterTable(DATA, FirmwareInfo),
 			 &size, &frev, &crev);
+	PP_ASSERT_WITH_CODE(fw_info != NULL,
+			    "Missing firmware info!", return -EINVAL);
 
 	if ((fw_info->ucTableFormatRevision == 1)
 	    && (le16_to_cpu(fw_info->usStructureSize) >= sizeof(ATOM_FIRMWARE_INFO_V1_4)))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu10_hwmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu10_hwmgr.c
@@ -773,13 +773,13 @@
 		smum_send_msg_to_smc_with_parameter(hwmgr,
 						PPSMC_MSG_SetHardMinFclkByFreq,
 						hwmgr->display_config->num_display > 3 ?
-						data->clock_vol_info.vdd_dep_on_fclk->entries[0].clk :
+						(data->clock_vol_info.vdd_dep_on_fclk->entries[0].clk / 100) :
 						min_mclk,
 						NULL);
 
 		smum_send_msg_to_smc_with_parameter(hwmgr,
 						PPSMC_MSG_SetHardMinSocclkByFreq,
-						data->clock_vol_info.vdd_dep_on_socclk->entries[0].clk,
+						data->clock_vol_info.vdd_dep_on_socclk->entries[0].clk / 100,
 						NULL);
 		smum_send_msg_to_smc_with_parameter(hwmgr,
 						PPSMC_MSG_SetHardMinVcn,
@@ -792,11 +792,11 @@
 						NULL);
 		smum_send_msg_to_smc_with_parameter(hwmgr,
 						PPSMC_MSG_SetSoftMaxFclkByFreq,
-						data->clock_vol_info.vdd_dep_on_fclk->entries[index_fclk].clk,
+						data->clock_vol_info.vdd_dep_on_fclk->entries[index_fclk].clk / 100,
 						NULL);
 		smum_send_msg_to_smc_with_parameter(hwmgr,
 						PPSMC_MSG_SetSoftMaxSocclkByFreq,
-						data->clock_vol_info.vdd_dep_on_socclk->entries[index_socclk].clk,
+						data->clock_vol_info.vdd_dep_on_socclk->entries[index_socclk].clk / 100,
 						NULL);
 		smum_send_msg_to_smc_with_parameter(hwmgr,
 						PPSMC_MSG_SetSoftMaxVcn,
@@ -1026,7 +1026,9 @@
 
 	switch (type) {
 	case PP_SCLK:
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetGfxclkFrequency, &now);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetGfxclkFrequency, &now);
+		if (ret)
+			return ret;
 
 	/* driver only know min/max gfx_clk, Add level 1 for all other gfx clks */
 		if (now == data->gfx_max_freq_limit/100)
@@ -1036,21 +1038,23 @@
 		else
 			i = 1;
 
-		size += sysfs_emit_at(buf, size, "0: %uMhz %s\n",
+		size += sprintf(buf + size, "0: %uMhz %s\n",
 					data->gfx_min_freq_limit/100,
 					i == 0 ? "*" : "");
-		size += sysfs_emit_at(buf, size, "1: %uMhz %s\n",
+		size += sprintf(buf + size, "1: %uMhz %s\n",
 					i == 1 ? now : SMU10_UMD_PSTATE_GFXCLK,
 					i == 1 ? "*" : "");
-		size += sysfs_emit_at(buf, size, "2: %uMhz %s\n",
+		size += sprintf(buf + size, "2: %uMhz %s\n",
 					data->gfx_max_freq_limit/100,
 					i == 2 ? "*" : "");
 		break;
 	case PP_MCLK:
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetFclkFrequency, &now);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetFclkFrequency, &now);
+		if (ret)
+			return ret;
 
 		for (i = 0; i < mclk_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i,
 					mclk_table->entries[i].clk / 100,
 					((mclk_table->entries[i].clk / 100)
@@ -1065,10 +1069,10 @@
 			if (ret)
 				return ret;
 
-			size = sysfs_emit(buf, "%s:\n", "OD_SCLK");
-			size += sysfs_emit_at(buf, size, "0: %10uMhz\n",
+			size += sprintf(buf + size, "%s:\n", "OD_SCLK");
+			size += sprintf(buf + size, "0: %10uMhz\n",
 			(data->gfx_actual_soft_min_freq > 0) ? data->gfx_actual_soft_min_freq : min_freq);
-			size += sysfs_emit_at(buf, size, "1: %10uMhz\n",
+			size += sprintf(buf + size, "1: %10uMhz\n",
 			(data->gfx_actual_soft_max_freq > 0) ? data->gfx_actual_soft_max_freq : max_freq);
 		}
 		break;
@@ -1081,8 +1085,8 @@
 			if (ret)
 				return ret;
 
-			size = sysfs_emit(buf, "%s:\n", "OD_RANGE");
-			size += sysfs_emit_at(buf, size, "SCLK: %7uMHz %10uMHz\n",
+			size += sprintf(buf + size, "%s:\n", "OD_RANGE");
+			size += sprintf(buf + size, "SCLK: %7uMHz %10uMHz\n",
 				min_freq, max_freq);
 		}
 		break;
@@ -1456,6 +1460,8 @@
 	if (!buf)
 		return -EINVAL;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	size += sysfs_emit_at(buf, size, "%s %16s %s %s %s %s\n",title[0],
 			title[1], title[2], title[3], title[4], title[5]);
 
@@ -1545,7 +1551,10 @@
 		}
 
 		if (input[0] == 0) {
-			smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMinGfxclkFrequency, &min_freq);
+			ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMinGfxclkFrequency, &min_freq);
+			if (ret)
+				return ret;
+
 			if (input[1] < min_freq) {
 				pr_err("Fine grain setting minimum sclk (%ld) MHz is less than the minimum allowed (%d) MHz\n",
 					input[1], min_freq);
@@ -1553,7 +1562,10 @@
 			}
 			smu10_data->gfx_actual_soft_min_freq = input[1];
 		} else if (input[0] == 1) {
-			smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxGfxclkFrequency, &max_freq);
+			ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxGfxclkFrequency, &max_freq);
+			if (ret)
+				return ret;
+
 			if (input[1] > max_freq) {
 				pr_err("Fine grain setting maximum sclk (%ld) MHz is greater than the maximum allowed (%d) MHz\n",
 					input[1], max_freq);
@@ -1568,10 +1580,15 @@
 			pr_err("Input parameter number not correct\n");
 			return -EINVAL;
 		}
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMinGfxclkFrequency, &min_freq);
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxGfxclkFrequency, &max_freq);
-
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMinGfxclkFrequency, &min_freq);
+		if (ret)
+			return ret;
 		smu10_data->gfx_actual_soft_min_freq = min_freq;
+
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxGfxclkFrequency, &max_freq);
+		if (ret)
+			return ret;
+
 		smu10_data->gfx_actual_soft_max_freq = max_freq;
 	} else if (type == PP_OD_COMMIT_DPM_TABLE) {
 		if (size != 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu7_hwmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu7_hwmgr.c
@@ -2907,6 +2907,7 @@
 
 static int smu7_hwmgr_backend_init(struct pp_hwmgr *hwmgr)
 {
+	struct amdgpu_device *adev = hwmgr->adev;
 	struct smu7_hwmgr *data;
 	int result = 0;
 
@@ -2924,6 +2925,8 @@
 		result = smu7_get_evv_voltages(hwmgr);
 		if (result) {
 			pr_info("Get EVV Voltage Failed.  Abort Driver loading!\n");
+			kfree(hwmgr->backend);
+			hwmgr->backend = NULL;
 			return -EINVAL;
 		}
 	} else {
@@ -2941,38 +2944,37 @@
 	/* Initalize Dynamic State Adjustment Rule Settings */
 	result = phm_initializa_dynamic_state_adjustment_rule_settings(hwmgr);
 
-	if (0 == result) {
-		struct amdgpu_device *adev = hwmgr->adev;
+	if (result)
+		goto fail;
 
-		data->is_tlu_enabled = false;
+	data->is_tlu_enabled = false;
 
-		hwmgr->platform_descriptor.hardwareActivityPerformanceLevels =
+	hwmgr->platform_descriptor.hardwareActivityPerformanceLevels =
 							SMU7_MAX_HARDWARE_POWERLEVELS;
-		hwmgr->platform_descriptor.hardwarePerformanceLevels = 2;
-		hwmgr->platform_descriptor.minimumClocksReductionPercentage = 50;
+	hwmgr->platform_descriptor.hardwarePerformanceLevels = 2;
+	hwmgr->platform_descriptor.minimumClocksReductionPercentage = 50;
 
-		data->pcie_gen_cap = adev->pm.pcie_gen_mask;
-		if (data->pcie_gen_cap & CAIL_PCIE_LINK_SPEED_SUPPORT_GEN3)
-			data->pcie_spc_cap = 20;
-		else
-			data->pcie_spc_cap = 16;
-		data->pcie_lane_cap = adev->pm.pcie_mlw_mask;
+	data->pcie_gen_cap = adev->pm.pcie_gen_mask;
+	if (data->pcie_gen_cap & CAIL_PCIE_LINK_SPEED_SUPPORT_GEN3)
+		data->pcie_spc_cap = 20;
+	else
+		data->pcie_spc_cap = 16;
+	data->pcie_lane_cap = adev->pm.pcie_mlw_mask;
 
-		hwmgr->platform_descriptor.vbiosInterruptId = 0x20000400; /* IRQ_SOURCE1_SW_INT */
-/* The true clock step depends on the frequency, typically 4.5 or 9 MHz. Here we use 5. */
-		hwmgr->platform_descriptor.clockStep.engineClock = 500;
-		hwmgr->platform_descriptor.clockStep.memoryClock = 500;
-		smu7_thermal_parameter_init(hwmgr);
-	} else {
-		/* Ignore return value in here, we are cleaning up a mess. */
-		smu7_hwmgr_backend_fini(hwmgr);
-	}
+	hwmgr->platform_descriptor.vbiosInterruptId = 0x20000400; /* IRQ_SOURCE1_SW_INT */
+	/* The true clock step depends on the frequency, typically 4.5 or 9 MHz. Here we use 5. */
+	hwmgr->platform_descriptor.clockStep.engineClock = 500;
+	hwmgr->platform_descriptor.clockStep.memoryClock = 500;
+	smu7_thermal_parameter_init(hwmgr);
 
 	result = smu7_update_edc_leakage_table(hwmgr);
 	if (result)
-		return result;
+		goto fail;
 
 	return 0;
+fail:
+	smu7_hwmgr_backend_fini(hwmgr);
+	return result;
 }
 
 static int smu7_force_dpm_highest(struct pp_hwmgr *hwmgr)
@@ -3273,8 +3275,7 @@
 			const struct pp_power_state *current_ps)
 {
 	struct amdgpu_device *adev = hwmgr->adev;
-	struct smu7_power_state *smu7_ps =
-				cast_phw_smu7_power_state(&request_ps->hardware);
+	struct smu7_power_state *smu7_ps;
 	uint32_t sclk;
 	uint32_t mclk;
 	struct PP_Clocks minimum_clocks = {0};
@@ -3291,6 +3292,10 @@
 	uint32_t latency;
 	bool latency_allowed = false;
 
+	smu7_ps = cast_phw_smu7_power_state(&request_ps->hardware);
+	if (!smu7_ps)
+		return -EINVAL;
+
 	data->battery_state = (PP_StateUILabel_Battery ==
 			request_ps->classification.ui_label);
 	data->mclk_ignore_signal = false;
@@ -4926,7 +4931,7 @@
 		now = i;
 
 		for (i = 0; i < sclk_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, sclk_table->dpm_levels[i].value / 100,
 					(i == now) ? "*" : "");
 		break;
@@ -4941,7 +4946,7 @@
 		now = i;
 
 		for (i = 0; i < mclk_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, mclk_table->dpm_levels[i].value / 100,
 					(i == now) ? "*" : "");
 		break;
@@ -4955,7 +4960,7 @@
 		now = i;
 
 		for (i = 0; i < pcie_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %s %s\n", i,
+			size += sprintf(buf + size, "%d: %s %s\n", i,
 					(pcie_table->dpm_levels[i].value == 0) ? "2.5GT/s, x8" :
 					(pcie_table->dpm_levels[i].value == 1) ? "5.0GT/s, x16" :
 					(pcie_table->dpm_levels[i].value == 2) ? "8.0GT/s, x16" : "",
@@ -4963,32 +4968,32 @@
 		break;
 	case OD_SCLK:
 		if (hwmgr->od_enabled) {
-			size = sysfs_emit(buf, "%s:\n", "OD_SCLK");
+			size += sprintf(buf + size, "%s:\n", "OD_SCLK");
 			for (i = 0; i < odn_sclk_table->num_of_pl; i++)
-				size += sysfs_emit_at(buf, size, "%d: %10uMHz %10umV\n",
+				size += sprintf(buf + size, "%d: %10uMHz %10umV\n",
 					i, odn_sclk_table->entries[i].clock/100,
 					odn_sclk_table->entries[i].vddc);
 		}
 		break;
 	case OD_MCLK:
 		if (hwmgr->od_enabled) {
-			size = sysfs_emit(buf, "%s:\n", "OD_MCLK");
+			size += sprintf(buf + size, "%s:\n", "OD_MCLK");
 			for (i = 0; i < odn_mclk_table->num_of_pl; i++)
-				size += sysfs_emit_at(buf, size, "%d: %10uMHz %10umV\n",
+				size += sprintf(buf + size, "%d: %10uMHz %10umV\n",
 					i, odn_mclk_table->entries[i].clock/100,
 					odn_mclk_table->entries[i].vddc);
 		}
 		break;
 	case OD_RANGE:
 		if (hwmgr->od_enabled) {
-			size = sysfs_emit(buf, "%s:\n", "OD_RANGE");
-			size += sysfs_emit_at(buf, size, "SCLK: %7uMHz %10uMHz\n",
+			size += sprintf(buf + size, "%s:\n", "OD_RANGE");
+			size += sprintf(buf + size, "SCLK: %7uMHz %10uMHz\n",
 				data->golden_dpm_table.sclk_table.dpm_levels[0].value/100,
 				hwmgr->platform_descriptor.overdriveLimit.engineClock/100);
-			size += sysfs_emit_at(buf, size, "MCLK: %7uMHz %10uMHz\n",
+			size += sprintf(buf + size, "MCLK: %7uMHz %10uMHz\n",
 				data->golden_dpm_table.mclk_table.dpm_levels[0].value/100,
 				hwmgr->platform_descriptor.overdriveLimit.memoryClock/100);
-			size += sysfs_emit_at(buf, size, "VDDC: %7umV %11umV\n",
+			size += sprintf(buf + size, "VDDC: %7umV %11umV\n",
 				data->odn_dpm_table.min_vddc,
 				data->odn_dpm_table.max_vddc);
 		}
@@ -5518,6 +5523,8 @@
 	if (!buf)
 		return -EINVAL;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	size += sysfs_emit_at(buf, size, "%s %16s %16s %16s %16s %16s %16s %16s\n",
 			title[0], title[1], title[2], title[3],
 			title[4], title[5], title[6], title[7]);
@@ -5590,7 +5597,7 @@
 	mode = input[size];
 	switch (mode) {
 	case PP_SMC_POWER_PROFILE_CUSTOM:
-		if (size < 8 && size != 0)
+		if (size != 8 && size != 0)
 			return -EINVAL;
 		/* If only CUSTOM is passed in, use the saved values. Check
 		 * that we actually have a CUSTOM profile by ensuring that
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu8_hwmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu8_hwmgr.c
@@ -584,6 +584,7 @@
 				hwmgr->dyn_state.uvd_clock_voltage_dependency_table;
 	unsigned long clock = 0;
 	uint32_t level;
+	int ret;
 
 	if (NULL == table || table->count <= 0)
 		return -EINVAL;
@@ -591,7 +592,9 @@
 	data->uvd_dpm.soft_min_clk = 0;
 	data->uvd_dpm.hard_min_clk = 0;
 
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxUvdLevel, &level);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxUvdLevel, &level);
+	if (ret)
+		return ret;
 
 	if (level < table->count)
 		clock = table->entries[level].vclk;
@@ -611,6 +614,7 @@
 				hwmgr->dyn_state.vce_clock_voltage_dependency_table;
 	unsigned long clock = 0;
 	uint32_t level;
+	int ret;
 
 	if (NULL == table || table->count <= 0)
 		return -EINVAL;
@@ -618,7 +622,9 @@
 	data->vce_dpm.soft_min_clk = 0;
 	data->vce_dpm.hard_min_clk = 0;
 
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxEclkLevel, &level);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxEclkLevel, &level);
+	if (ret)
+		return ret;
 
 	if (level < table->count)
 		clock = table->entries[level].ecclk;
@@ -638,6 +644,7 @@
 				hwmgr->dyn_state.acp_clock_voltage_dependency_table;
 	unsigned long clock = 0;
 	uint32_t level;
+	int ret;
 
 	if (NULL == table || table->count <= 0)
 		return -EINVAL;
@@ -645,7 +652,9 @@
 	data->acp_dpm.soft_min_clk = 0;
 	data->acp_dpm.hard_min_clk = 0;
 
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxAclkLevel, &level);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetMaxAclkLevel, &level);
+	if (ret)
+		return ret;
 
 	if (level < table->count)
 		clock = table->entries[level].acpclk;
@@ -1051,16 +1060,18 @@
 				struct pp_power_state  *prequest_ps,
 			const struct pp_power_state *pcurrent_ps)
 {
-	struct smu8_power_state *smu8_ps =
-				cast_smu8_power_state(&prequest_ps->hardware);
-
-	const struct smu8_power_state *smu8_current_ps =
-				cast_const_smu8_power_state(&pcurrent_ps->hardware);
-
+	struct smu8_power_state *smu8_ps;
+	const struct smu8_power_state *smu8_current_ps;
 	struct smu8_hwmgr *data = hwmgr->backend;
 	struct PP_Clocks clocks = {0, 0, 0, 0};
 	bool force_high;
 
+	smu8_ps = cast_smu8_power_state(&prequest_ps->hardware);
+	smu8_current_ps = cast_const_smu8_power_state(&pcurrent_ps->hardware);
+
+	if (!smu8_ps || !smu8_current_ps)
+		return -EINVAL;
+
 	smu8_ps->need_dfs_bypass = true;
 
 	data->battery_state = (PP_StateUILabel_Battery == prequest_ps->classification.ui_label);
@@ -1559,7 +1570,7 @@
 				CURR_SCLK_INDEX);
 
 		for (i = 0; i < sclk_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, sclk_table->entries[i].clk / 100,
 					(i == now) ? "*" : "");
 		break;
@@ -1571,7 +1582,7 @@
 				CURR_MCLK_INDEX);
 
 		for (i = SMU8_NUM_NBPMEMORYCLOCK; i > 0; i--)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					SMU8_NUM_NBPMEMORYCLOCK-i, data->sys_info.nbp_memory_clock[i-1] / 100,
 					(SMU8_NUM_NBPMEMORYCLOCK-i == now) ? "*" : "");
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu_helper.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu_helper.h
@@ -109,6 +109,19 @@
 			   struct amdgpu_irq_src *source,
 			   struct amdgpu_iv_entry *entry);
 
+/*
+ * Helper function to make sysfs_emit_at() happy. Align buf to
+ * the current page boundary and record the offset.
+ */
+static inline void phm_get_sysfs_buf(char **buf, int *offset)
+{
+	if (!*buf || !offset)
+		return;
+
+	*offset = offset_in_page(*buf);
+	*buf -= *offset;
+}
+
 int smu9_register_irq_handlers(struct pp_hwmgr *hwmgr);
 
 void *smu_atom_get_data_table(void *dev, uint32_t table, uint16_t *size,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega10_hwmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega10_hwmgr.c
@@ -355,13 +355,13 @@
 	return 0;
 }
 
-static void vega10_init_dpm_defaults(struct pp_hwmgr *hwmgr)
+static int vega10_init_dpm_defaults(struct pp_hwmgr *hwmgr)
 {
 	struct vega10_hwmgr *data = hwmgr->backend;
-	int i;
 	uint32_t sub_vendor_id, hw_revision;
 	uint32_t top32, bottom32;
 	struct amdgpu_device *adev = hwmgr->adev;
+	int ret, i;
 
 	vega10_initialize_power_tune_defaults(hwmgr);
 
@@ -486,9 +486,12 @@
 	if (data->registry_data.vr0hot_enabled)
 		data->smu_features[GNLD_VR0HOT].supported = true;
 
-	smum_send_msg_to_smc(hwmgr,
+	ret = smum_send_msg_to_smc(hwmgr,
 			PPSMC_MSG_GetSmuVersion,
 			&hwmgr->smu_version);
+	if (ret)
+		return ret;
+
 		/* ACG firmware has major version 5 */
 	if ((hwmgr->smu_version & 0xff000000) == 0x5000000)
 		data->smu_features[GNLD_ACG].supported = true;
@@ -506,10 +509,16 @@
 		data->smu_features[GNLD_PCC_LIMIT].supported = true;
 
 	/* Get the SN to turn into a Unique ID */
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumTop32, &top32);
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumBottom32, &bottom32);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumTop32, &top32);
+	if (ret)
+		return ret;
+
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumBottom32, &bottom32);
+	if (ret)
+		return ret;
 
 	adev->unique_id = ((uint64_t)bottom32 << 32) | top32;
+	return 0;
 }
 
 #ifdef PPLIB_VEGA10_EVV_SUPPORT
@@ -883,7 +892,9 @@
 
 	vega10_set_features_platform_caps(hwmgr);
 
-	vega10_init_dpm_defaults(hwmgr);
+	result = vega10_init_dpm_defaults(hwmgr);
+	if (result)
+		return result;
 
 #ifdef PPLIB_VEGA10_EVV_SUPPORT
 	/* Get leakage voltage based on leakage ID. */
@@ -2354,15 +2365,20 @@
 {
 	struct vega10_hwmgr *data = hwmgr->backend;
 	uint32_t agc_btc_response;
+	int ret;
 
 	if (data->smu_features[GNLD_ACG].supported) {
 		if (0 == vega10_enable_smc_features(hwmgr, true,
 					data->smu_features[GNLD_DPM_PREFETCHER].smu_feature_bitmap))
 			data->smu_features[GNLD_DPM_PREFETCHER].enabled = true;
 
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_InitializeAcg, NULL);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_InitializeAcg, NULL);
+		if (ret)
+			return ret;
 
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_RunAcgBtc, &agc_btc_response);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_RunAcgBtc, &agc_btc_response);
+		if (ret)
+			agc_btc_response = 0;
 
 		if (1 == agc_btc_response) {
 			if (1 == data->acg_loop_state)
@@ -2575,8 +2591,11 @@
 		}
 	}
 
-	pp_atomfwctrl_get_voltage_table_v4(hwmgr, VOLTAGE_TYPE_VDDC,
+	result = pp_atomfwctrl_get_voltage_table_v4(hwmgr, VOLTAGE_TYPE_VDDC,
 			VOLTAGE_OBJ_SVID2,  &voltage_table);
+	PP_ASSERT_WITH_CODE(!result,
+			"Failed to get voltage table!",
+			return result);
 	pp_table->MaxVidStep = voltage_table.max_vid_step;
 
 	pp_table->GfxDpmVoltageMode =
@@ -3237,8 +3256,7 @@
 			const struct pp_power_state *current_ps)
 {
 	struct amdgpu_device *adev = hwmgr->adev;
-	struct vega10_power_state *vega10_ps =
-				cast_phw_vega10_power_state(&request_ps->hardware);
+	struct vega10_power_state *vega10_ps;
 	uint32_t sclk;
 	uint32_t mclk;
 	struct PP_Clocks minimum_clocks = {0};
@@ -3256,6 +3274,10 @@
 	uint32_t stable_pstate_sclk = 0, stable_pstate_mclk = 0;
 	uint32_t latency;
 
+	vega10_ps = cast_phw_vega10_power_state(&request_ps->hardware);
+	if (!vega10_ps)
+		return -EINVAL;
+
 	data->battery_state = (PP_StateUILabel_Battery ==
 			request_ps->classification.ui_label);
 
@@ -3393,13 +3415,17 @@
 	const struct vega10_power_state *vega10_ps =
 			cast_const_phw_vega10_power_state(states->pnew_state);
 	struct vega10_single_dpm_table *sclk_table = &(data->dpm_table.gfx_table);
-	uint32_t sclk = vega10_ps->performance_levels
-			[vega10_ps->performance_level_count - 1].gfx_clock;
 	struct vega10_single_dpm_table *mclk_table = &(data->dpm_table.mem_table);
-	uint32_t mclk = vega10_ps->performance_levels
-			[vega10_ps->performance_level_count - 1].mem_clock;
+	uint32_t sclk, mclk;
 	uint32_t i;
 
+	if (vega10_ps == NULL)
+		return -EINVAL;
+	sclk = vega10_ps->performance_levels
+			[vega10_ps->performance_level_count - 1].gfx_clock;
+	mclk = vega10_ps->performance_levels
+			[vega10_ps->performance_level_count - 1].mem_clock;
+
 	for (i = 0; i < sclk_table->count; i++) {
 		if (sclk == sclk_table->dpm_levels[i].value)
 			break;
@@ -3706,6 +3732,9 @@
 			cast_const_phw_vega10_power_state(states->pnew_state);
 	int i;
 
+	if (vega10_ps == NULL)
+		return -EINVAL;
+
 	PP_ASSERT_WITH_CODE(!vega10_trim_dpm_states(hwmgr, vega10_ps),
 			"Attempt to Trim DPM States Failed!",
 			return -1);
@@ -3878,11 +3907,14 @@
 		uint32_t *query)
 {
 	uint32_t value;
+	int ret;
 
 	if (!query)
 		return -EINVAL;
 
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrPkgPwr, &value);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrPkgPwr, &value);
+	if (ret)
+		return ret;
 
 	/* SMC returning actual watts, keep consistent with legacy asics, low 8 bit as 8 fractional bits */
 	*query = value << 8;
@@ -4548,6 +4580,8 @@
 	int ret = 0;
 	int size = 0;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	ret = vega10_get_enabled_smc_features(hwmgr, &features_enabled);
 	PP_ASSERT_WITH_CODE(!ret,
 			"[EnableAllSmuFeatures] Failed to get enabled smc features!",
@@ -4635,14 +4669,16 @@
 	uint32_t gen_speed, lane_width, current_gen_speed, current_lane_width;
 	PPTable_t *pptable = &(data->smc_state_table.pp_table);
 
-	int i, now, size = 0, count = 0;
+	int i, ret, now,  size = 0, count = 0;
 
 	switch (type) {
 	case PP_SCLK:
 		if (data->registry_data.sclk_dpm_key_disabled)
 			break;
 
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrentGfxclkIndex, &now);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrentGfxclkIndex, &now);
+		if (ret)
+			break;
 
 		if (hwmgr->pp_one_vf &&
 		    (hwmgr->dpm_level == AMD_DPM_FORCED_LEVEL_PROFILE_PEAK))
@@ -4650,7 +4686,7 @@
 		else
 			count = sclk_table->count;
 		for (i = 0; i < count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, sclk_table->dpm_levels[i].value / 100,
 					(i == now) ? "*" : "");
 		break;
@@ -4658,10 +4694,12 @@
 		if (data->registry_data.mclk_dpm_key_disabled)
 			break;
 
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrentUclkIndex, &now);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrentUclkIndex, &now);
+		if (ret)
+			break;
 
 		for (i = 0; i < mclk_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, mclk_table->dpm_levels[i].value / 100,
 					(i == now) ? "*" : "");
 		break;
@@ -4669,10 +4707,12 @@
 		if (data->registry_data.socclk_dpm_key_disabled)
 			break;
 
-		smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrentSocclkIndex, &now);
+		ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_GetCurrentSocclkIndex, &now);
+		if (ret)
+			break;
 
 		for (i = 0; i < soc_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, soc_table->dpm_levels[i].value / 100,
 					(i == now) ? "*" : "");
 		break;
@@ -4680,11 +4720,13 @@
 		if (data->registry_data.dcefclk_dpm_key_disabled)
 			break;
 
-		smum_send_msg_to_smc_with_parameter(hwmgr,
+		ret = smum_send_msg_to_smc_with_parameter(hwmgr,
 				PPSMC_MSG_GetClockFreqMHz, CLK_DCEFCLK, &now);
+		if (ret)
+			break;
 
 		for (i = 0; i < dcef_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 					i, dcef_table->dpm_levels[i].value / 100,
 					(dcef_table->dpm_levels[i].value / 100 == now) ?
 					"*" : "");
@@ -4698,7 +4740,7 @@
 			gen_speed = pptable->PcieGenSpeed[i];
 			lane_width = pptable->PcieLaneCount[i];
 
-			size += sysfs_emit_at(buf, size, "%d: %s %s %s\n", i,
+			size += sprintf(buf + size, "%d: %s %s %s\n", i,
 					(gen_speed == 0) ? "2.5GT/s," :
 					(gen_speed == 1) ? "5.0GT/s," :
 					(gen_speed == 2) ? "8.0GT/s," :
@@ -4717,34 +4759,34 @@
 
 	case OD_SCLK:
 		if (hwmgr->od_enabled) {
-			size = sysfs_emit(buf, "%s:\n", "OD_SCLK");
+			size += sprintf(buf + size, "%s:\n", "OD_SCLK");
 			podn_vdd_dep = &data->odn_dpm_table.vdd_dep_on_sclk;
 			for (i = 0; i < podn_vdd_dep->count; i++)
-				size += sysfs_emit_at(buf, size, "%d: %10uMhz %10umV\n",
+				size += sprintf(buf + size, "%d: %10uMhz %10umV\n",
 					i, podn_vdd_dep->entries[i].clk / 100,
 						podn_vdd_dep->entries[i].vddc);
 		}
 		break;
 	case OD_MCLK:
 		if (hwmgr->od_enabled) {
-			size = sysfs_emit(buf, "%s:\n", "OD_MCLK");
+			size += sprintf(buf + size, "%s:\n", "OD_MCLK");
 			podn_vdd_dep = &data->odn_dpm_table.vdd_dep_on_mclk;
 			for (i = 0; i < podn_vdd_dep->count; i++)
-				size += sysfs_emit_at(buf, size, "%d: %10uMhz %10umV\n",
+				size += sprintf(buf + size, "%d: %10uMhz %10umV\n",
 					i, podn_vdd_dep->entries[i].clk/100,
 						podn_vdd_dep->entries[i].vddc);
 		}
 		break;
 	case OD_RANGE:
 		if (hwmgr->od_enabled) {
-			size = sysfs_emit(buf, "%s:\n", "OD_RANGE");
-			size += sysfs_emit_at(buf, size, "SCLK: %7uMHz %10uMHz\n",
+			size += sprintf(buf + size, "%s:\n", "OD_RANGE");
+			size += sprintf(buf + size, "SCLK: %7uMHz %10uMHz\n",
 				data->golden_dpm_table.gfx_table.dpm_levels[0].value/100,
 				hwmgr->platform_descriptor.overdriveLimit.engineClock/100);
-			size += sysfs_emit_at(buf, size, "MCLK: %7uMHz %10uMHz\n",
+			size += sprintf(buf + size, "MCLK: %7uMHz %10uMHz\n",
 				data->golden_dpm_table.mem_table.dpm_levels[0].value/100,
 				hwmgr->platform_descriptor.overdriveLimit.memoryClock/100);
-			size += sysfs_emit_at(buf, size, "VDDC: %7umV %11umV\n",
+			size += sprintf(buf + size, "VDDC: %7umV %11umV\n",
 				data->odn_dpm_table.min_vddc,
 				data->odn_dpm_table.max_vddc);
 		}
@@ -4830,6 +4872,9 @@
 
 	psa = cast_const_phw_vega10_power_state(pstate1);
 	psb = cast_const_phw_vega10_power_state(pstate2);
+	if (psa == NULL || psb == NULL)
+		return -EINVAL;
+
 	/* If the two states don't even have the same number of performance levels they cannot be the same state. */
 	if (psa->performance_level_count != psb->performance_level_count) {
 		*equal = false;
@@ -4955,6 +5000,8 @@
 		return -EINVAL;
 
 	vega10_ps = cast_phw_vega10_power_state(&ps->hardware);
+	if (vega10_ps == NULL)
+		return -EINVAL;
 
 	vega10_ps->performance_levels
 	[vega10_ps->performance_level_count - 1].gfx_clock =
@@ -5006,6 +5053,8 @@
 		return -EINVAL;
 
 	vega10_ps = cast_phw_vega10_power_state(&ps->hardware);
+	if (vega10_ps == NULL)
+		return -EINVAL;
 
 	vega10_ps->performance_levels
 	[vega10_ps->performance_level_count - 1].mem_clock =
@@ -5112,6 +5161,8 @@
 	if (!buf)
 		return -EINVAL;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	size += sysfs_emit_at(buf, size, "%s %16s %s %s %s %s\n",title[0],
 			title[1], title[2], title[3], title[4], title[5]);
 
@@ -5241,6 +5292,9 @@
 		return;
 
 	vega10_ps = cast_phw_vega10_power_state(&ps->hardware);
+	if (vega10_ps == NULL)
+		return;
+
 	max_level = vega10_ps->performance_level_count - 1;
 
 	if (vega10_ps->performance_levels[max_level].gfx_clock !=
@@ -5263,6 +5317,9 @@
 
 	ps = (struct pp_power_state *)((unsigned long)(hwmgr->ps) + hwmgr->ps_size * (hwmgr->num_ps - 1));
 	vega10_ps = cast_phw_vega10_power_state(&ps->hardware);
+	if (vega10_ps == NULL)
+		return;
+
 	max_level = vega10_ps->performance_level_count - 1;
 
 	if (vega10_ps->performance_levels[max_level].gfx_clock !=
@@ -5453,6 +5510,8 @@
 		return -EINVAL;
 
 	ps = cast_const_phw_vega10_power_state(state);
+	if (ps == NULL)
+		return -EINVAL;
 
 	i = index > ps->performance_level_count - 1 ?
 			ps->performance_level_count - 1 : index;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega10_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega10_thermal.c
@@ -67,22 +67,21 @@
 int vega10_fan_ctrl_get_fan_speed_pwm(struct pp_hwmgr *hwmgr,
 		uint32_t *speed)
 {
-	uint32_t current_rpm;
-	uint32_t percent = 0;
+	struct amdgpu_device *adev = hwmgr->adev;
+	uint32_t duty100, duty;
+	uint64_t tmp64;
 
-	if (hwmgr->thermal_controller.fanInfo.bNoFan)
-		return 0;
+	duty100 = REG_GET_FIELD(RREG32_SOC15(THM, 0, mmCG_FDO_CTRL1),
+				CG_FDO_CTRL1, FMAX_DUTY100);
+	duty = REG_GET_FIELD(RREG32_SOC15(THM, 0, mmCG_THERMAL_STATUS),
+				CG_THERMAL_STATUS, FDO_PWM_DUTY);
 
-	if (vega10_get_current_rpm(hwmgr, &current_rpm))
-		return -1;
+	if (!duty100)
+		return -EINVAL;
 
-	if (hwmgr->thermal_controller.
-			advanceFanControlParameters.usMaxFanRPM != 0)
-		percent = current_rpm * 255 /
-			hwmgr->thermal_controller.
-			advanceFanControlParameters.usMaxFanRPM;
-
-	*speed = MIN(percent, 255);
+	tmp64 = (uint64_t)duty * 255;
+	do_div(tmp64, duty100);
+	*speed = MIN((uint32_t)tmp64, 255);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega12_hwmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega12_hwmgr.c
@@ -294,12 +294,12 @@
 	return 0;
 }
 
-static void vega12_init_dpm_defaults(struct pp_hwmgr *hwmgr)
+static int vega12_init_dpm_defaults(struct pp_hwmgr *hwmgr)
 {
 	struct vega12_hwmgr *data = (struct vega12_hwmgr *)(hwmgr->backend);
 	struct amdgpu_device *adev = hwmgr->adev;
 	uint32_t top32, bottom32;
-	int i;
+	int i, ret;
 
 	data->smu_features[GNLD_DPM_PREFETCHER].smu_feature_id =
 			FEATURE_DPM_PREFETCHER_BIT;
@@ -365,10 +365,16 @@
 	}
 
 	/* Get the SN to turn into a Unique ID */
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumTop32, &top32);
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumBottom32, &bottom32);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumTop32, &top32);
+	if (ret)
+		return ret;
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumBottom32, &bottom32);
+	if (ret)
+		return ret;
 
 	adev->unique_id = ((uint64_t)bottom32 << 32) | top32;
+
+	return 0;
 }
 
 static int vega12_set_private_data_based_on_pptable(struct pp_hwmgr *hwmgr)
@@ -411,7 +417,11 @@
 
 	vega12_set_features_platform_caps(hwmgr);
 
-	vega12_init_dpm_defaults(hwmgr);
+	result = vega12_init_dpm_defaults(hwmgr);
+	if (result) {
+		pr_err("%s failed\n", __func__);
+		return result;
+	}
 
 	/* Parse pptable data read from VBIOS */
 	vega12_set_private_data_based_on_pptable(hwmgr);
@@ -2141,6 +2151,8 @@
 	int ret = 0;
 	int size = 0;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	ret = vega12_get_enabled_smc_features(hwmgr, &features_enabled);
 	PP_ASSERT_WITH_CODE(!ret,
 		"[EnableAllSmuFeatures] Failed to get enabled smc features!",
@@ -2256,7 +2268,7 @@
 				"Attempt to get gfx clk levels Failed!",
 				return -1);
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz / 1000 == now / 100) ? "*" : "");
 		break;
@@ -2272,7 +2284,7 @@
 				"Attempt to get memory clk levels Failed!",
 				return -1);
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz / 1000 == now / 100) ? "*" : "");
 		break;
@@ -2290,7 +2302,7 @@
 				"Attempt to get soc clk levels Failed!",
 				return -1);
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz / 1000 == now) ? "*" : "");
 		break;
@@ -2308,7 +2320,7 @@
 				"Attempt to get dcef clk levels Failed!",
 				return -1);
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz / 1000 == now) ? "*" : "");
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega20_hwmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/hwmgr/vega20_hwmgr.c
@@ -329,12 +329,12 @@
 	return 0;
 }
 
-static void vega20_init_dpm_defaults(struct pp_hwmgr *hwmgr)
+static int vega20_init_dpm_defaults(struct pp_hwmgr *hwmgr)
 {
 	struct vega20_hwmgr *data = (struct vega20_hwmgr *)(hwmgr->backend);
 	struct amdgpu_device *adev = hwmgr->adev;
 	uint32_t top32, bottom32;
-	int i;
+	int i, ret;
 
 	data->smu_features[GNLD_DPM_PREFETCHER].smu_feature_id =
 			FEATURE_DPM_PREFETCHER_BIT;
@@ -405,10 +405,17 @@
 	}
 
 	/* Get the SN to turn into a Unique ID */
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumTop32, &top32);
-	smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumBottom32, &bottom32);
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumTop32, &top32);
+	if (ret)
+		return ret;
+
+	ret = smum_send_msg_to_smc(hwmgr, PPSMC_MSG_ReadSerialNumBottom32, &bottom32);
+	if (ret)
+		return ret;
 
 	adev->unique_id = ((uint64_t)bottom32 << 32) | top32;
+
+	return 0;
 }
 
 static int vega20_set_private_data_based_on_pptable(struct pp_hwmgr *hwmgr)
@@ -428,6 +435,7 @@
 {
 	struct vega20_hwmgr *data;
 	struct amdgpu_device *adev = hwmgr->adev;
+	int result;
 
 	data = kzalloc(sizeof(struct vega20_hwmgr), GFP_KERNEL);
 	if (data == NULL)
@@ -453,8 +461,11 @@
 
 	vega20_set_features_platform_caps(hwmgr);
 
-	vega20_init_dpm_defaults(hwmgr);
-
+	result = vega20_init_dpm_defaults(hwmgr);
+	if (result) {
+		pr_err("%s failed\n", __func__);
+		return result;
+	}
 	/* Parse pptable data read from VBIOS */
 	vega20_set_private_data_based_on_pptable(hwmgr);
 
@@ -2961,7 +2972,8 @@
 			data->od8_settings.od8_settings_array;
 	OverDriveTable_t *od_table =
 			&(data->smc_state_table.overdrive_table);
-	int32_t input_index, input_clk, input_vol, i;
+	int32_t input_clk, input_vol, i;
+	uint32_t input_index;
 	int od8_id;
 	int ret;
 
@@ -3238,6 +3250,8 @@
 	int ret = 0;
 	int size = 0;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	ret = vega20_get_enabled_smc_features(hwmgr, &features_enabled);
 	PP_ASSERT_WITH_CODE(!ret,
 			"[EnableAllSmuFeatures] Failed to get enabled smc features!",
@@ -3372,13 +3386,13 @@
 				return ret);
 
 		if (vega20_get_sclks(hwmgr, &clocks)) {
-			size += sysfs_emit_at(buf, size, "0: %uMhz * (DPM disabled)\n",
+			size += sprintf(buf + size, "0: %uMhz * (DPM disabled)\n",
 				now / 100);
 			break;
 		}
 
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz == now * 10) ? "*" : "");
 		break;
@@ -3390,13 +3404,13 @@
 				return ret);
 
 		if (vega20_get_memclocks(hwmgr, &clocks)) {
-			size += sysfs_emit_at(buf, size, "0: %uMhz * (DPM disabled)\n",
+			size += sprintf(buf + size, "0: %uMhz * (DPM disabled)\n",
 				now / 100);
 			break;
 		}
 
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz == now * 10) ? "*" : "");
 		break;
@@ -3408,13 +3422,13 @@
 				return ret);
 
 		if (vega20_get_socclocks(hwmgr, &clocks)) {
-			size += sysfs_emit_at(buf, size, "0: %uMhz * (DPM disabled)\n",
+			size += sprintf(buf + size, "0: %uMhz * (DPM disabled)\n",
 				now / 100);
 			break;
 		}
 
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz == now * 10) ? "*" : "");
 		break;
@@ -3426,7 +3440,7 @@
 				return ret);
 
 		for (i = 0; i < fclk_dpm_table->count; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, fclk_dpm_table->dpm_levels[i].value,
 				fclk_dpm_table->dpm_levels[i].value == (now / 100) ? "*" : "");
 		break;
@@ -3438,13 +3452,13 @@
 				return ret);
 
 		if (vega20_get_dcefclocks(hwmgr, &clocks)) {
-			size += sysfs_emit_at(buf, size, "0: %uMhz * (DPM disabled)\n",
+			size += sprintf(buf + size, "0: %uMhz * (DPM disabled)\n",
 				now / 100);
 			break;
 		}
 
 		for (i = 0; i < clocks.num_levels; i++)
-			size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n",
+			size += sprintf(buf + size, "%d: %uMhz %s\n",
 				i, clocks.data[i].clocks_in_khz / 1000,
 				(clocks.data[i].clocks_in_khz == now * 10) ? "*" : "");
 		break;
@@ -3458,7 +3472,7 @@
 			gen_speed = pptable->PcieGenSpeed[i];
 			lane_width = pptable->PcieLaneCount[i];
 
-			size += sysfs_emit_at(buf, size, "%d: %s %s %dMhz %s\n", i,
+			size += sprintf(buf + size, "%d: %s %s %dMhz %s\n", i,
 					(gen_speed == 0) ? "2.5GT/s," :
 					(gen_speed == 1) ? "5.0GT/s," :
 					(gen_speed == 2) ? "8.0GT/s," :
@@ -3479,18 +3493,18 @@
 	case OD_SCLK:
 		if (od8_settings[OD8_SETTING_GFXCLK_FMIN].feature_id &&
 		    od8_settings[OD8_SETTING_GFXCLK_FMAX].feature_id) {
-			size = sysfs_emit(buf, "%s:\n", "OD_SCLK");
-			size += sysfs_emit_at(buf, size, "0: %10uMhz\n",
+			size += sprintf(buf + size, "%s:\n", "OD_SCLK");
+			size += sprintf(buf + size, "0: %10uMhz\n",
 				od_table->GfxclkFmin);
-			size += sysfs_emit_at(buf, size, "1: %10uMhz\n",
+			size += sprintf(buf + size, "1: %10uMhz\n",
 				od_table->GfxclkFmax);
 		}
 		break;
 
 	case OD_MCLK:
 		if (od8_settings[OD8_SETTING_UCLK_FMAX].feature_id) {
-			size = sysfs_emit(buf, "%s:\n", "OD_MCLK");
-			size += sysfs_emit_at(buf, size, "1: %10uMhz\n",
+			size += sprintf(buf + size, "%s:\n", "OD_MCLK");
+			size += sprintf(buf + size, "1: %10uMhz\n",
 				od_table->UclkFmax);
 		}
 
@@ -3503,14 +3517,14 @@
 		    od8_settings[OD8_SETTING_GFXCLK_VOLTAGE1].feature_id &&
 		    od8_settings[OD8_SETTING_GFXCLK_VOLTAGE2].feature_id &&
 		    od8_settings[OD8_SETTING_GFXCLK_VOLTAGE3].feature_id) {
-			size = sysfs_emit(buf, "%s:\n", "OD_VDDC_CURVE");
-			size += sysfs_emit_at(buf, size, "0: %10uMhz %10dmV\n",
+			size += sprintf(buf + size, "%s:\n", "OD_VDDC_CURVE");
+			size += sprintf(buf + size, "0: %10uMhz %10dmV\n",
 				od_table->GfxclkFreq1,
 				od_table->GfxclkVolt1 / VOLTAGE_SCALE);
-			size += sysfs_emit_at(buf, size, "1: %10uMhz %10dmV\n",
+			size += sprintf(buf + size, "1: %10uMhz %10dmV\n",
 				od_table->GfxclkFreq2,
 				od_table->GfxclkVolt2 / VOLTAGE_SCALE);
-			size += sysfs_emit_at(buf, size, "2: %10uMhz %10dmV\n",
+			size += sprintf(buf + size, "2: %10uMhz %10dmV\n",
 				od_table->GfxclkFreq3,
 				od_table->GfxclkVolt3 / VOLTAGE_SCALE);
 		}
@@ -3518,17 +3532,17 @@
 		break;
 
 	case OD_RANGE:
-		size = sysfs_emit(buf, "%s:\n", "OD_RANGE");
+		size += sprintf(buf + size, "%s:\n", "OD_RANGE");
 
 		if (od8_settings[OD8_SETTING_GFXCLK_FMIN].feature_id &&
 		    od8_settings[OD8_SETTING_GFXCLK_FMAX].feature_id) {
-			size += sysfs_emit_at(buf, size, "SCLK: %7uMhz %10uMhz\n",
+			size += sprintf(buf + size, "SCLK: %7uMhz %10uMhz\n",
 				od8_settings[OD8_SETTING_GFXCLK_FMIN].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_FMAX].max_value);
 		}
 
 		if (od8_settings[OD8_SETTING_UCLK_FMAX].feature_id) {
-			size += sysfs_emit_at(buf, size, "MCLK: %7uMhz %10uMhz\n",
+			size += sprintf(buf + size, "MCLK: %7uMhz %10uMhz\n",
 				od8_settings[OD8_SETTING_UCLK_FMAX].min_value,
 				od8_settings[OD8_SETTING_UCLK_FMAX].max_value);
 		}
@@ -3539,22 +3553,22 @@
 		    od8_settings[OD8_SETTING_GFXCLK_VOLTAGE1].feature_id &&
 		    od8_settings[OD8_SETTING_GFXCLK_VOLTAGE2].feature_id &&
 		    od8_settings[OD8_SETTING_GFXCLK_VOLTAGE3].feature_id) {
-			size += sysfs_emit_at(buf, size, "VDDC_CURVE_SCLK[0]: %7uMhz %10uMhz\n",
+			size += sprintf(buf + size, "VDDC_CURVE_SCLK[0]: %7uMhz %10uMhz\n",
 				od8_settings[OD8_SETTING_GFXCLK_FREQ1].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_FREQ1].max_value);
-			size += sysfs_emit_at(buf, size, "VDDC_CURVE_VOLT[0]: %7dmV %11dmV\n",
+			size += sprintf(buf + size, "VDDC_CURVE_VOLT[0]: %7dmV %11dmV\n",
 				od8_settings[OD8_SETTING_GFXCLK_VOLTAGE1].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_VOLTAGE1].max_value);
-			size += sysfs_emit_at(buf, size, "VDDC_CURVE_SCLK[1]: %7uMhz %10uMhz\n",
+			size += sprintf(buf + size, "VDDC_CURVE_SCLK[1]: %7uMhz %10uMhz\n",
 				od8_settings[OD8_SETTING_GFXCLK_FREQ2].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_FREQ2].max_value);
-			size += sysfs_emit_at(buf, size, "VDDC_CURVE_VOLT[1]: %7dmV %11dmV\n",
+			size += sprintf(buf + size, "VDDC_CURVE_VOLT[1]: %7dmV %11dmV\n",
 				od8_settings[OD8_SETTING_GFXCLK_VOLTAGE2].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_VOLTAGE2].max_value);
-			size += sysfs_emit_at(buf, size, "VDDC_CURVE_SCLK[2]: %7uMhz %10uMhz\n",
+			size += sprintf(buf + size, "VDDC_CURVE_SCLK[2]: %7uMhz %10uMhz\n",
 				od8_settings[OD8_SETTING_GFXCLK_FREQ3].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_FREQ3].max_value);
-			size += sysfs_emit_at(buf, size, "VDDC_CURVE_VOLT[2]: %7dmV %11dmV\n",
+			size += sprintf(buf + size, "VDDC_CURVE_VOLT[2]: %7dmV %11dmV\n",
 				od8_settings[OD8_SETTING_GFXCLK_VOLTAGE3].min_value,
 				od8_settings[OD8_SETTING_GFXCLK_VOLTAGE3].max_value);
 		}
@@ -4003,6 +4017,8 @@
 	if (!buf)
 		return -EINVAL;
 
+	phm_get_sysfs_buf(&buf, &size);
+
 	size += sysfs_emit_at(buf, size, "%16s %s %s %s %s %s %s %s %s %s %s\n",
 			title[0], title[1], title[2], title[3], title[4], title[5],
 			title[6], title[7], title[8], title[9], title[10]);
@@ -4093,9 +4109,11 @@
 	if (power_profile_mode == PP_SMC_POWER_PROFILE_CUSTOM) {
 		struct vega20_hwmgr *data =
 			(struct vega20_hwmgr *)(hwmgr->backend);
-		if (size == 0 && !data->is_custom_profile_set)
+
+		if (size != 10 && size != 0)
 			return -EINVAL;
-		if (size < 10 && size != 0)
+
+		if (size == 0 && !data->is_custom_profile_set)
 			return -EINVAL;
 
 		result = vega20_get_activity_monitor_coeff(hwmgr,
@@ -4157,6 +4175,8 @@
 			activity_monitor.Fclk_PD_Data_error_coeff = input[8];
 			activity_monitor.Fclk_PD_Data_error_rate_coeff = input[9];
 			break;
+		default:
+			return -EINVAL;
 		}
 
 		result = vega20_set_activity_monitor_coeff(hwmgr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/kv_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/kv_dpm.c
@@ -163,6 +163,8 @@
 
 	for (i = 0; i < SUMO_MAX_HARDWARE_POWERLEVELS; i++) {
 		if (table[i].ulSupportedSCLK != 0) {
+			if (table[i].usVoltageIndex >= SUMO_MAX_NUMBER_VOLTAGES)
+				continue;
 			vid_mapping_table->entries[table[i].usVoltageIndex].vid_7bit =
 				table[i].usVoltageID;
 			vid_mapping_table->entries[table[i].usVoltageIndex].vid_2bit =
@@ -1256,6 +1258,29 @@
 	}
 }
 
+static bool kv_is_internal_thermal_sensor(enum amdgpu_int_thermal_type sensor)
+{
+	switch (sensor) {
+	case THERMAL_TYPE_RV6XX:
+	case THERMAL_TYPE_RV770:
+	case THERMAL_TYPE_EVERGREEN:
+	case THERMAL_TYPE_SUMO:
+	case THERMAL_TYPE_NI:
+	case THERMAL_TYPE_SI:
+	case THERMAL_TYPE_CI:
+	case THERMAL_TYPE_KV:
+		return true;
+	case THERMAL_TYPE_ADT7473_WITH_INTERNAL:
+	case THERMAL_TYPE_EMC2103_WITH_INTERNAL:
+		return false; /* need special handling */
+	case THERMAL_TYPE_NONE:
+	case THERMAL_TYPE_EXTERNAL:
+	case THERMAL_TYPE_EXTERNAL_GPIO:
+	default:
+		return false;
+	}
+}
+
 static int kv_dpm_enable(struct amdgpu_device *adev)
 {
 	struct kv_power_info *pi = kv_get_pi(adev);
@@ -1352,7 +1377,7 @@
 	}
 
 	if (adev->irq.installed &&
-	    amdgpu_is_internal_thermal_sensor(adev->pm.int_thermal_type)) {
+	    kv_is_internal_thermal_sensor(adev->pm.int_thermal_type)) {
 		ret = kv_set_thermal_temperature_range(adev, KV_TEMP_RANGE_MIN, KV_TEMP_RANGE_MAX);
 		if (ret) {
 			DRM_ERROR("kv_set_thermal_temperature_range failed\n");
@@ -1609,19 +1634,7 @@
 
 static u8 kv_get_acp_boot_level(struct amdgpu_device *adev)
 {
-	u8 i;
-	struct amdgpu_clock_voltage_dependency_table *table =
-		&adev->pm.dpm.dyn_state.acp_clock_voltage_dependency_table;
-
-	for (i = 0; i < table->count; i++) {
-		if (table->entries[i].clk >= 0) /* XXX */
-			break;
-	}
-
-	if (i >= table->count)
-		i = table->count - 1;
-
-	return i;
+	return 0;
 }
 
 static void kv_update_acp_boot_level(struct amdgpu_device *adev)
@@ -2743,10 +2756,8 @@
 		non_clock_info = (struct _ATOM_PPLIB_NONCLOCK_INFO *)
 			&non_clock_info_array->nonClockInfo[non_clock_array_index];
 		ps = kzalloc(sizeof(struct kv_ps), GFP_KERNEL);
-		if (ps == NULL) {
-			kfree(adev->pm.dpm.ps);
+		if (ps == NULL)
 			return -ENOMEM;
-		}
 		adev->pm.dpm.ps[i].ps_priv = ps;
 		k = 0;
 		idx = (u8 *)&power_state->v2.clockInfoIndex[0];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/si_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/si_dpm.c
@@ -7247,17 +7247,15 @@
 	if (!adev->pm.dpm.ps)
 		return -ENOMEM;
 	power_state_offset = (u8 *)state_array->states;
-	for (i = 0; i < state_array->ucNumEntries; i++) {
+	for (adev->pm.dpm.num_ps = 0, i = 0; i < state_array->ucNumEntries; i++) {
 		u8 *idx;
 		power_state = (union pplib_power_state *)power_state_offset;
 		non_clock_array_index = power_state->v2.nonClockInfoIndex;
 		non_clock_info = (struct _ATOM_PPLIB_NONCLOCK_INFO *)
 			&non_clock_info_array->nonClockInfo[non_clock_array_index];
 		ps = kzalloc(sizeof(struct  si_ps), GFP_KERNEL);
-		if (ps == NULL) {
-			kfree(adev->pm.dpm.ps);
+		if (ps == NULL)
 			return -ENOMEM;
-		}
 		adev->pm.dpm.ps[i].ps_priv = ps;
 		si_parse_pplib_non_clock_info(adev, &adev->pm.dpm.ps[i],
 					      non_clock_info,
@@ -7279,8 +7277,8 @@
 			k++;
 		}
 		power_state_offset += 2 + power_state->v2.ucNumDPMLevels;
+		adev->pm.dpm.num_ps++;
 	}
-	adev->pm.dpm.num_ps = state_array->ucNumEntries;
 
 	/* fill in the vce power states */
 	for (i = 0; i < adev->pm.dpm.num_of_vce_states; i++) {
@@ -7348,10 +7346,9 @@
 		kcalloc(4,
 			sizeof(struct amdgpu_clock_voltage_dependency_entry),
 			GFP_KERNEL);
-	if (!adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries) {
-		amdgpu_free_extended_power_table(adev);
+	if (!adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries)
 		return -ENOMEM;
-	}
+
 	adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.count = 4;
 	adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries[0].clk = 0;
 	adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries[0].v = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/powerplay/smumgr/vega10_smumgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/powerplay/smumgr/vega10_smumgr.c
@@ -130,13 +130,17 @@
 			    uint64_t *features_enabled)
 {
 	uint32_t enabled_features;
+	int ret;
 
 	if (features_enabled == NULL)
 		return -EINVAL;
 
-	smum_send_msg_to_smc(hwmgr,
+	ret = smum_send_msg_to_smc(hwmgr,
 			PPSMC_MSG_GetEnabledSmuFeatures,
 			&enabled_features);
+	if (ret)
+		return ret;
+
 	*features_enabled = enabled_features;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c
@@ -138,7 +138,7 @@
 			   uint32_t *min,
 			   uint32_t *max)
 {
-	int ret = 0;
+	int ret = -ENOTSUPP;
 
 	if (!min && !max)
 		return -EINVAL;
@@ -1536,9 +1536,7 @@
 
 	smu->watermarks_bitmap &= ~(WATERMARKS_LOADED);
 
-	/* skip CGPG when in S0ix */
-	if (smu->is_apu && !adev->in_s0ix)
-		smu_set_gfx_cgpg(&adev->smu, false);
+	smu_set_gfx_cgpg(&adev->smu, false);
 
 	return 0;
 }
@@ -1569,8 +1567,7 @@
 		return ret;
 	}
 
-	if (smu->is_apu)
-		smu_set_gfx_cgpg(&adev->smu, true);
+	smu_set_gfx_cgpg(&adev->smu, true);
 
 	smu->disable_uclk_switch = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu11/navi10_ppt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu11/navi10_ppt.c
@@ -1231,19 +1231,22 @@
 					   value);
 }
 
-static bool navi10_is_support_fine_grained_dpm(struct smu_context *smu, enum smu_clk_type clk_type)
+static int navi10_is_support_fine_grained_dpm(struct smu_context *smu, enum smu_clk_type clk_type)
 {
 	PPTable_t *pptable = smu->smu_table.driver_pptable;
 	DpmDescriptor_t *dpm_desc = NULL;
-	uint32_t clk_index = 0;
+	int clk_index = 0;
 
 	clk_index = smu_cmn_to_asic_specific_index(smu,
 						   CMN2ASIC_MAPPING_CLK,
 						   clk_type);
+	if (clk_index < 0)
+		return clk_index;
+
 	dpm_desc = &pptable->DpmDescriptor[clk_index];
 
 	/* 0 - Fine grained DPM, 1 - Discrete DPM */
-	return dpm_desc->SnapToDiscrete == 0;
+	return dpm_desc->SnapToDiscrete == 0 ? 1 : 0;
 }
 
 static inline bool navi10_od_feature_is_supported(struct smu_11_0_overdrive_table *od_table, enum SMU_11_0_ODFEATURE_CAP cap)
@@ -1265,7 +1268,7 @@
 			enum smu_clk_type clk_type, char *buf)
 {
 	uint16_t *curve_settings;
-	int i, size = 0, ret = 0;
+	int i, levels, size = 0, ret = 0;
 	uint32_t cur_value = 0, value = 0, count = 0;
 	uint32_t freq_values[3] = {0};
 	uint32_t mark_index = 0;
@@ -1299,7 +1302,11 @@
 		if (ret)
 			return size;
 
-		if (!navi10_is_support_fine_grained_dpm(smu, clk_type)) {
+		ret = navi10_is_support_fine_grained_dpm(smu, clk_type);
+		if (ret < 0)
+			return ret;
+
+		if (!ret) {
 			for (i = 0; i < count; i++) {
 				ret = smu_v11_0_get_dpm_freq_by_index(smu, clk_type, i, &value);
 				if (ret)
@@ -1319,14 +1326,17 @@
 			freq_values[1] = cur_value;
 			mark_index = cur_value == freq_values[0] ? 0 :
 				     cur_value == freq_values[2] ? 2 : 1;
-			if (mark_index != 1)
-				freq_values[1] = (freq_values[0] + freq_values[2]) / 2;
 
-			for (i = 0; i < 3; i++) {
+			levels = 3;
+			if (mark_index != 1) {
+				levels = 2;
+				freq_values[1] = freq_values[2];
+			}
+
+			for (i = 0; i < levels; i++) {
 				size += sysfs_emit_at(buf, size, "%d: %uMhz %s\n", i, freq_values[i],
 						i == mark_index ? "*" : "");
 			}
-
 		}
 		break;
 	case SMU_PCIE:
@@ -1465,7 +1475,11 @@
 	case SMU_UCLK:
 	case SMU_FCLK:
 		/* There is only 2 levels for fine grained DPM */
-		if (navi10_is_support_fine_grained_dpm(smu, clk_type)) {
+		ret = navi10_is_support_fine_grained_dpm(smu, clk_type);
+		if (ret < 0)
+			return ret;
+
+		if (ret) {
 			soft_max_level = (soft_max_level >= 1 ? 1 : 0);
 			soft_min_level = (soft_min_level >= 1 ? 1 : 0);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu11/sienna_cichlid_ppt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu11/sienna_cichlid_ppt.c
@@ -338,7 +338,7 @@
 	if (smu->dc_controlled_by_gpio)
        *(uint64_t *)feature_mask |= FEATURE_MASK(FEATURE_ACDC_BIT);
 
-	if (amdgpu_aspm)
+	if (amdgpu_device_should_use_aspm(adev))
 		*(uint64_t *)feature_mask |= FEATURE_MASK(FEATURE_DS_LCLK_BIT);
 
 	return 0;
@@ -358,6 +358,23 @@
 		smu_baco->platform_support =
 			(val & RCC_BIF_STRAP0__STRAP_PX_CAPABLE_MASK) ? true :
 									false;
+
+		/*
+		 * Disable BACO entry/exit completely on below SKUs to
+		 * avoid hardware intermittent failures.
+		 */
+		if (((adev->pdev->device == 0x73A1) &&
+		    (adev->pdev->revision == 0x00)) ||
+		    ((adev->pdev->device == 0x73BF) &&
+		    (adev->pdev->revision == 0xCF)) ||
+		    ((adev->pdev->device == 0x7422) &&
+		    (adev->pdev->revision == 0x00)) ||
+		    ((adev->pdev->device == 0x73A3) &&
+		    (adev->pdev->revision == 0x00)) ||
+		    ((adev->pdev->device == 0x73E3) &&
+		    (adev->pdev->revision == 0x00)))
+			smu_baco->platform_support = false;
+
 	}
 }
 
@@ -418,6 +435,36 @@
 	return 0;
 }
 
+static int sienna_cichlid_patch_pptable_quirk(struct smu_context *smu)
+{
+	struct amdgpu_device *adev = smu->adev;
+	uint32_t *board_reserved;
+	uint16_t *freq_table_gfx;
+	uint32_t i;
+
+	/* Fix some OEM SKU specific stability issues */
+	GET_PPTABLE_MEMBER(BoardReserved, &board_reserved);
+	if ((adev->pdev->device == 0x73DF) &&
+	    (adev->pdev->revision == 0XC3) &&
+	    (adev->pdev->subsystem_device == 0x16C2) &&
+	    (adev->pdev->subsystem_vendor == 0x1043))
+		board_reserved[0] = 1387;
+
+	GET_PPTABLE_MEMBER(FreqTableGfx, &freq_table_gfx);
+	if ((adev->pdev->device == 0x73DF) &&
+	    (adev->pdev->revision == 0XC3) &&
+	    ((adev->pdev->subsystem_device == 0x16C2) ||
+	    (adev->pdev->subsystem_device == 0x133C)) &&
+	    (adev->pdev->subsystem_vendor == 0x1043)) {
+		for (i = 0; i < NUM_GFXCLK_DPM_LEVELS; i++) {
+			if (freq_table_gfx[i] > 2500)
+				freq_table_gfx[i] = 2500;
+		}
+	}
+
+	return 0;
+}
+
 static int sienna_cichlid_setup_pptable(struct smu_context *smu)
 {
 	int ret = 0;
@@ -438,7 +485,7 @@
 	if (ret)
 		return ret;
 
-	return ret;
+	return sienna_cichlid_patch_pptable_quirk(smu);
 }
 
 static int sienna_cichlid_tables_init(struct smu_context *smu)
@@ -1278,21 +1325,37 @@
 				&dpm_context->dpm_tables.soc_table;
 	struct smu_umd_pstate_table *pstate_table =
 				&smu->pstate_table;
+	struct amdgpu_device *adev = smu->adev;
 
 	pstate_table->gfxclk_pstate.min = gfx_table->min;
 	pstate_table->gfxclk_pstate.peak = gfx_table->max;
-	if (gfx_table->max >= SIENNA_CICHLID_UMD_PSTATE_PROFILING_GFXCLK)
-		pstate_table->gfxclk_pstate.standard = SIENNA_CICHLID_UMD_PSTATE_PROFILING_GFXCLK;
 
 	pstate_table->uclk_pstate.min = mem_table->min;
 	pstate_table->uclk_pstate.peak = mem_table->max;
-	if (mem_table->max >= SIENNA_CICHLID_UMD_PSTATE_PROFILING_MEMCLK)
-		pstate_table->uclk_pstate.standard = SIENNA_CICHLID_UMD_PSTATE_PROFILING_MEMCLK;
 
 	pstate_table->socclk_pstate.min = soc_table->min;
 	pstate_table->socclk_pstate.peak = soc_table->max;
-	if (soc_table->max >= SIENNA_CICHLID_UMD_PSTATE_PROFILING_SOCCLK)
+
+	switch (adev->asic_type) {
+	case CHIP_SIENNA_CICHLID:
+	case CHIP_NAVY_FLOUNDER:
+		pstate_table->gfxclk_pstate.standard = SIENNA_CICHLID_UMD_PSTATE_PROFILING_GFXCLK;
+		pstate_table->uclk_pstate.standard = SIENNA_CICHLID_UMD_PSTATE_PROFILING_MEMCLK;
 		pstate_table->socclk_pstate.standard = SIENNA_CICHLID_UMD_PSTATE_PROFILING_SOCCLK;
+		break;
+	case CHIP_DIMGREY_CAVEFISH:
+		pstate_table->gfxclk_pstate.standard = DIMGREY_CAVEFISH_UMD_PSTATE_PROFILING_GFXCLK;
+		pstate_table->uclk_pstate.standard = DIMGREY_CAVEFISH_UMD_PSTATE_PROFILING_MEMCLK;
+		pstate_table->socclk_pstate.standard = DIMGREY_CAVEFISH_UMD_PSTATE_PROFILING_SOCCLK;
+		break;
+	case CHIP_BEIGE_GOBY:
+		pstate_table->gfxclk_pstate.standard = BEIGE_GOBY_UMD_PSTATE_PROFILING_GFXCLK;
+		pstate_table->uclk_pstate.standard = BEIGE_GOBY_UMD_PSTATE_PROFILING_MEMCLK;
+		pstate_table->socclk_pstate.standard = BEIGE_GOBY_UMD_PSTATE_PROFILING_SOCCLK;
+		break;
+	default:
+		break;
+	}
 
 	return 0;
 }
@@ -1865,33 +1928,94 @@
 	return 0;
 }
 
+static void sienna_cichlid_get_override_pcie_settings(struct smu_context *smu,
+						      uint32_t *gen_speed_override,
+						      uint32_t *lane_width_override)
+{
+	struct amdgpu_device *adev = smu->adev;
+
+	*gen_speed_override = 0xff;
+	*lane_width_override = 0xff;
+
+	switch (adev->pdev->device) {
+	case 0x73A0:
+	case 0x73A1:
+	case 0x73A2:
+	case 0x73A3:
+	case 0x73AB:
+	case 0x73AE:
+		/* Bit 7:0: PCIE lane width, 1 to 7 corresponds is x1 to x32 */
+		*lane_width_override = 6;
+		break;
+	case 0x73E0:
+	case 0x73E1:
+	case 0x73E3:
+		*lane_width_override = 4;
+		break;
+	case 0x7420:
+	case 0x7421:
+	case 0x7422:
+	case 0x7423:
+	case 0x7424:
+		*lane_width_override = 3;
+		break;
+	default:
+		break;
+	}
+}
+
+#define MAX(a, b)	((a) > (b) ? (a) : (b))
+
 static int sienna_cichlid_update_pcie_parameters(struct smu_context *smu,
 					 uint32_t pcie_gen_cap,
 					 uint32_t pcie_width_cap)
 {
 	struct smu_11_0_dpm_context *dpm_context = smu->smu_dpm.dpm_context;
-
-	uint32_t smu_pcie_arg;
+	struct smu_11_0_pcie_table *pcie_table = &dpm_context->dpm_tables.pcie_table;
+	uint32_t gen_speed_override, lane_width_override;
 	uint8_t *table_member1, *table_member2;
+	uint32_t min_gen_speed, max_gen_speed;
+	uint32_t min_lane_width, max_lane_width;
+	uint32_t smu_pcie_arg;
 	int ret, i;
 
 	GET_PPTABLE_MEMBER(PcieGenSpeed, &table_member1);
 	GET_PPTABLE_MEMBER(PcieLaneCount, &table_member2);
 
-	/* lclk dpm table setup */
-	for (i = 0; i < MAX_PCIE_CONF; i++) {
-		dpm_context->dpm_tables.pcie_table.pcie_gen[i] = table_member1[i];
-		dpm_context->dpm_tables.pcie_table.pcie_lane[i] = table_member2[i];
+	sienna_cichlid_get_override_pcie_settings(smu,
+						  &gen_speed_override,
+						  &lane_width_override);
+
+	/* PCIE gen speed override */
+	if (gen_speed_override != 0xff) {
+		min_gen_speed = MIN(pcie_gen_cap, gen_speed_override);
+		max_gen_speed = MIN(pcie_gen_cap, gen_speed_override);
+	} else {
+		min_gen_speed = MAX(0, table_member1[0]);
+		max_gen_speed = MIN(pcie_gen_cap, table_member1[1]);
+		min_gen_speed = min_gen_speed > max_gen_speed ?
+				max_gen_speed : min_gen_speed;
+	}
+	pcie_table->pcie_gen[0] = min_gen_speed;
+	pcie_table->pcie_gen[1] = max_gen_speed;
+
+	/* PCIE lane width override */
+	if (lane_width_override != 0xff) {
+		min_lane_width = MIN(pcie_width_cap, lane_width_override);
+		max_lane_width = MIN(pcie_width_cap, lane_width_override);
+	} else {
+		min_lane_width = MAX(1, table_member2[0]);
+		max_lane_width = MIN(pcie_width_cap, table_member2[1]);
+		min_lane_width = min_lane_width > max_lane_width ?
+				 max_lane_width : min_lane_width;
 	}
+	pcie_table->pcie_lane[0] = min_lane_width;
+	pcie_table->pcie_lane[1] = max_lane_width;
 
 	for (i = 0; i < NUM_LINK_LEVELS; i++) {
-		smu_pcie_arg = (i << 16) |
-			((table_member1[i] <= pcie_gen_cap) ?
-			 (table_member1[i] << 8) :
-			 (pcie_gen_cap << 8)) |
-			((table_member2[i] <= pcie_width_cap) ?
-			 table_member2[i] :
-			 pcie_width_cap);
+		smu_pcie_arg = (i << 16 |
+				pcie_table->pcie_gen[i] << 8 |
+				pcie_table->pcie_lane[i]);
 
 		ret = smu_cmn_send_smc_msg_with_param(smu,
 				SMU_MSG_OverridePcieParameters,
@@ -1899,11 +2023,6 @@
 				NULL);
 		if (ret)
 			return ret;
-
-		if (table_member1[i] > pcie_gen_cap)
-			dpm_context->dpm_tables.pcie_table.pcie_gen[i] = pcie_gen_cap;
-		if (table_member2[i] > pcie_width_cap)
-			dpm_context->dpm_tables.pcie_table.pcie_lane[i] = pcie_width_cap;
 	}
 
 	return 0;
@@ -1950,16 +2069,9 @@
 		(OverDriveTable_t *)smu->smu_table.boot_overdrive_table;
 	OverDriveTable_t *user_od_table =
 		(OverDriveTable_t *)smu->smu_table.user_overdrive_table;
+	OverDriveTable_t user_od_table_bak;
 	int ret = 0;
 
-	/*
-	 * For S3/S4/Runpm resume, no need to setup those overdrive tables again as
-	 *   - either they already have the default OD settings got during cold bootup
-	 *   - or they have some user customized OD settings which cannot be overwritten
-	 */
-	if (smu->adev->in_suspend)
-		return 0;
-
 	ret = smu_cmn_update_table(smu, SMU_TABLE_OVERDRIVE,
 				   0, (void *)boot_od_table, false);
 	if (ret) {
@@ -1970,7 +2082,23 @@
 	sienna_cichlid_dump_od_table(smu, boot_od_table);
 
 	memcpy(od_table, boot_od_table, sizeof(OverDriveTable_t));
-	memcpy(user_od_table, boot_od_table, sizeof(OverDriveTable_t));
+
+	/*
+	 * For S3/S4/Runpm resume, we need to setup those overdrive tables again,
+	 * but we have to preserve user defined values in "user_od_table".
+	 */
+	if (!smu->adev->in_suspend) {
+		memcpy(user_od_table, boot_od_table, sizeof(OverDriveTable_t));
+		smu->user_dpm_profile.user_od = false;
+	} else if (smu->user_dpm_profile.user_od) {
+		memcpy(&user_od_table_bak, user_od_table, sizeof(OverDriveTable_t));
+		memcpy(user_od_table, boot_od_table, sizeof(OverDriveTable_t));
+		user_od_table->GfxclkFmin = user_od_table_bak.GfxclkFmin;
+		user_od_table->GfxclkFmax = user_od_table_bak.GfxclkFmax;
+		user_od_table->UclkFmin = user_od_table_bak.UclkFmin;
+		user_od_table->UclkFmax = user_od_table_bak.UclkFmax;
+		user_od_table->VddGfxOffset = user_od_table_bak.VddGfxOffset;
+	}
 
 	return 0;
 }
@@ -2180,6 +2308,20 @@
 	return ret;
 }
 
+static int sienna_cichlid_restore_user_od_settings(struct smu_context *smu)
+{
+	struct smu_table_context *table_context = &smu->smu_table;
+	OverDriveTable_t *od_table = table_context->overdrive_table;
+	OverDriveTable_t *user_od_table = table_context->user_overdrive_table;
+	int res;
+
+	res = smu_v11_0_restore_user_od_settings(smu);
+	if (res == 0)
+		memcpy(od_table, user_od_table, sizeof(OverDriveTable_t));
+
+	return res;
+}
+
 static int sienna_cichlid_run_btc(struct smu_context *smu)
 {
 	return smu_cmn_send_smc_msg(smu, SMU_MSG_RunDcBtc, NULL);
@@ -3728,14 +3870,14 @@
 
 static int sienna_cichlid_enable_mgpu_fan_boost(struct smu_context *smu)
 {
-	struct smu_table_context *table_context = &smu->smu_table;
-	PPTable_t *smc_pptable = table_context->driver_pptable;
+	uint16_t *mgpu_fan_boost_limit_rpm;
 
+	GET_PPTABLE_MEMBER(MGpuFanBoostLimitRpm, &mgpu_fan_boost_limit_rpm);
 	/*
 	 * Skip the MGpuFanBoost setting for those ASICs
 	 * which do not support it
 	 */
-	if (!smc_pptable->MGpuFanBoostLimitRpm)
+	if (*mgpu_fan_boost_limit_rpm == 0)
 		return 0;
 
 	return smu_cmn_send_smc_msg_with_param(smu,
@@ -3869,6 +4011,7 @@
 	.dump_pptable = sienna_cichlid_dump_pptable,
 	.init_microcode = smu_v11_0_init_microcode,
 	.load_microcode = smu_v11_0_load_microcode,
+	.fini_microcode = smu_v11_0_fini_microcode,
 	.init_smc_tables = sienna_cichlid_init_smc_tables,
 	.fini_smc_tables = smu_v11_0_fini_smc_tables,
 	.init_power = smu_v11_0_init_power,
@@ -3916,7 +4059,7 @@
 	.set_soft_freq_limited_range = smu_v11_0_set_soft_freq_limited_range,
 	.set_default_od_settings = sienna_cichlid_set_default_od_settings,
 	.od_edit_dpm_table = sienna_cichlid_od_edit_dpm_table,
-	.restore_user_od_settings = smu_v11_0_restore_user_od_settings,
+	.restore_user_od_settings = sienna_cichlid_restore_user_od_settings,
 	.run_btc = sienna_cichlid_run_btc,
 	.set_power_source = smu_v11_0_set_power_source,
 	.get_pp_feature_mask = smu_cmn_get_pp_feature_mask,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu11/sienna_cichlid_ppt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu11/sienna_cichlid_ppt.h
@@ -33,6 +33,14 @@
 #define SIENNA_CICHLID_UMD_PSTATE_PROFILING_SOCCLK    960
 #define SIENNA_CICHLID_UMD_PSTATE_PROFILING_MEMCLK    1000
 
+#define DIMGREY_CAVEFISH_UMD_PSTATE_PROFILING_GFXCLK 1950
+#define DIMGREY_CAVEFISH_UMD_PSTATE_PROFILING_SOCCLK 960
+#define DIMGREY_CAVEFISH_UMD_PSTATE_PROFILING_MEMCLK 676
+
+#define BEIGE_GOBY_UMD_PSTATE_PROFILING_GFXCLK 2200
+#define BEIGE_GOBY_UMD_PSTATE_PROFILING_SOCCLK 960
+#define BEIGE_GOBY_UMD_PSTATE_PROFILING_MEMCLK 1000
+
 extern void sienna_cichlid_set_ppt_funcs(struct smu_context *smu);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu11/smu_v11_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu11/smu_v11_0.c
@@ -772,7 +772,7 @@
 		goto failed;
 	}
 
-	bitmap_copy((unsigned long *)feature_mask, feature->allowed, 64);
+	bitmap_to_arr32(feature_mask, feature->allowed, 64);
 
 	ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetAllowedFeaturesMaskHigh,
 					  feature_mask[1], NULL);
@@ -1235,6 +1235,8 @@
 	uint32_t crystal_clock_freq = 2500;
 	uint32_t tach_period;
 
+	if (speed == 0)
+		return -EINVAL;
 	/*
 	 * To prevent from possible overheat, some ASICs may have requirement
 	 * for minimum fan speed:
@@ -1593,6 +1595,10 @@
 	if (amdgpu_sriov_vf(smu->adev) || !smu_baco->platform_support)
 		return false;
 
+	/* return true if ASIC is in BACO state already */
+	if (smu_v11_0_baco_get_state(smu) == SMU_BACO_STATE_ENTER)
+		return true;
+
 	/* Arcturus does not support this bit mask */
 	if (smu_cmn_feature_is_supported(smu, SMU_FEATURE_BACO_BIT) &&
 	   !smu_cmn_feature_is_enabled(smu, SMU_FEATURE_BACO_BIT))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c
@@ -579,7 +579,7 @@
 	DpmClocks_t *clk_table = smu->smu_table.clocks_table;
 	SmuMetrics_legacy_t metrics;
 	struct smu_dpm_context *smu_dpm_ctx = &(smu->smu_dpm);
-	int i, size = 0, ret = 0;
+	int i, idx, size = 0, ret = 0;
 	uint32_t cur_value = 0, value = 0, count = 0;
 	bool cur_value_match_level = false;
 
@@ -653,7 +653,8 @@
 	case SMU_MCLK:
 	case SMU_FCLK:
 		for (i = 0; i < count; i++) {
-			ret = vangogh_get_dpm_clk_limited(smu, clk_type, i, &value);
+			idx = (clk_type == SMU_FCLK || clk_type == SMU_MCLK) ? (count - i - 1) : i;
+			ret = vangogh_get_dpm_clk_limited(smu, clk_type, idx, &value);
 			if (ret)
 				return ret;
 			if (!value)
@@ -680,7 +681,7 @@
 	DpmClocks_t *clk_table = smu->smu_table.clocks_table;
 	SmuMetrics_t metrics;
 	struct smu_dpm_context *smu_dpm_ctx = &(smu->smu_dpm);
-	int i, size = 0, ret = 0;
+	int i, idx, size = 0, ret = 0;
 	uint32_t cur_value = 0, value = 0, count = 0;
 	bool cur_value_match_level = false;
 
@@ -754,7 +755,8 @@
 	case SMU_MCLK:
 	case SMU_FCLK:
 		for (i = 0; i < count; i++) {
-			ret = vangogh_get_dpm_clk_limited(smu, clk_type, i, &value);
+			idx = (clk_type == SMU_FCLK || clk_type == SMU_MCLK) ? (count - i - 1) : i;
+			ret = vangogh_get_dpm_clk_limited(smu, clk_type, idx, &value);
 			if (ret)
 				return ret;
 			if (!value)
@@ -1386,52 +1388,38 @@
 	uint32_t soc_mask, mclk_mask, fclk_mask;
 	uint32_t vclk_mask = 0, dclk_mask = 0;
 
+	smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
+	smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
+
 	switch (level) {
 	case AMD_DPM_FORCED_LEVEL_HIGH:
-		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
+		smu->gfx_actual_hard_min_freq = smu->gfx_default_soft_max_freq;
 		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
 
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
 
 		ret = vangogh_force_dpm_limit_value(smu, true);
+		if (ret)
+			return ret;
 		break;
 	case AMD_DPM_FORCED_LEVEL_LOW:
 		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
-		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
-
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
+		smu->gfx_actual_soft_max_freq = smu->gfx_default_hard_min_freq;
 
 		ret = vangogh_force_dpm_limit_value(smu, false);
+		if (ret)
+			return ret;
 		break;
 	case AMD_DPM_FORCED_LEVEL_AUTO:
 		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
 		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
 
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
-
 		ret = vangogh_unforce_dpm_levels(smu);
-		break;
-	case AMD_DPM_FORCED_LEVEL_PROFILE_STANDARD:
-		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
-		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
-
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
-
-		ret = smu_cmn_send_smc_msg_with_param(smu,
-					SMU_MSG_SetHardMinGfxClk,
-					VANGOGH_UMD_PSTATE_STANDARD_GFXCLK, NULL);
-		if (ret)
-			return ret;
-
-		ret = smu_cmn_send_smc_msg_with_param(smu,
-					SMU_MSG_SetSoftMaxGfxClk,
-					VANGOGH_UMD_PSTATE_STANDARD_GFXCLK, NULL);
 		if (ret)
 			return ret;
+		break;
+	case AMD_DPM_FORCED_LEVEL_PROFILE_STANDARD:
+		smu->gfx_actual_hard_min_freq = VANGOGH_UMD_PSTATE_STANDARD_GFXCLK;
+		smu->gfx_actual_soft_max_freq = VANGOGH_UMD_PSTATE_STANDARD_GFXCLK;
 
 		ret = vangogh_get_profiling_clk_mask(smu, level,
 							&vclk_mask,
@@ -1446,32 +1434,15 @@
 		vangogh_force_clk_levels(smu, SMU_SOCCLK, 1 << soc_mask);
 		vangogh_force_clk_levels(smu, SMU_VCLK, 1 << vclk_mask);
 		vangogh_force_clk_levels(smu, SMU_DCLK, 1 << dclk_mask);
-
 		break;
 	case AMD_DPM_FORCED_LEVEL_PROFILE_MIN_SCLK:
 		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
-		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
-
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
-
-		ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetHardMinVcn,
-								VANGOGH_UMD_PSTATE_PEAK_DCLK, NULL);
-		if (ret)
-			return ret;
-
-		ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetSoftMaxVcn,
-								VANGOGH_UMD_PSTATE_PEAK_DCLK, NULL);
-		if (ret)
-			return ret;
+		smu->gfx_actual_soft_max_freq = smu->gfx_default_hard_min_freq;
 		break;
 	case AMD_DPM_FORCED_LEVEL_PROFILE_MIN_MCLK:
 		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
 		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
 
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
-
 		ret = vangogh_get_profiling_clk_mask(smu, level,
 							NULL,
 							NULL,
@@ -1484,29 +1455,29 @@
 		vangogh_force_clk_levels(smu, SMU_FCLK, 1 << fclk_mask);
 		break;
 	case AMD_DPM_FORCED_LEVEL_PROFILE_PEAK:
-		smu->gfx_actual_hard_min_freq = smu->gfx_default_hard_min_freq;
-		smu->gfx_actual_soft_max_freq = smu->gfx_default_soft_max_freq;
-
-		smu->cpu_actual_soft_min_freq = smu->cpu_default_soft_min_freq;
-		smu->cpu_actual_soft_max_freq = smu->cpu_default_soft_max_freq;
-
-		ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetHardMinGfxClk,
-				VANGOGH_UMD_PSTATE_PEAK_GFXCLK, NULL);
-		if (ret)
-			return ret;
+		smu->gfx_actual_hard_min_freq = VANGOGH_UMD_PSTATE_PEAK_GFXCLK;
+		smu->gfx_actual_soft_max_freq = VANGOGH_UMD_PSTATE_PEAK_GFXCLK;
 
-		ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetSoftMaxGfxClk,
-				VANGOGH_UMD_PSTATE_PEAK_GFXCLK, NULL);
+		ret = vangogh_set_peak_clock_by_device(smu);
 		if (ret)
 			return ret;
-
-		ret = vangogh_set_peak_clock_by_device(smu);
 		break;
 	case AMD_DPM_FORCED_LEVEL_MANUAL:
 	case AMD_DPM_FORCED_LEVEL_PROFILE_EXIT:
 	default:
-		break;
+		return 0;
 	}
+
+	ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetHardMinGfxClk,
+					      smu->gfx_actual_hard_min_freq, NULL);
+	if (ret)
+		return ret;
+
+	ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetSoftMaxGfxClk,
+					      smu->gfx_actual_soft_max_freq, NULL);
+	if (ret)
+		return ret;
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c
@@ -485,7 +485,7 @@
 static int renoir_print_clk_levels(struct smu_context *smu,
 			enum smu_clk_type clk_type, char *buf)
 {
-	int i, size = 0, ret = 0;
+	int i, idx, size = 0, ret = 0;
 	uint32_t cur_value = 0, value = 0, count = 0, min = 0, max = 0;
 	SmuMetrics_t metrics;
 	struct smu_dpm_context *smu_dpm_ctx = &(smu->smu_dpm);
@@ -585,7 +585,8 @@
 	case SMU_VCLK:
 	case SMU_DCLK:
 		for (i = 0; i < count; i++) {
-			ret = renoir_get_dpm_clk_limited(smu, clk_type, i, &value);
+			idx = (clk_type == SMU_FCLK || clk_type == SMU_MCLK) ? (count - i - 1) : i;
+			ret = renoir_get_dpm_clk_limited(smu, clk_type, idx, &value);
 			if (ret)
 				return ret;
 			if (!value)
@@ -1127,6 +1128,39 @@
 	return size;
 }
 
+static void renoir_get_ss_power_percent(SmuMetrics_t *metrics,
+					uint32_t *apu_percent, uint32_t *dgpu_percent)
+{
+	uint32_t apu_boost = 0;
+	uint32_t dgpu_boost = 0;
+	uint16_t apu_limit = 0;
+	uint16_t dgpu_limit = 0;
+	uint16_t apu_power = 0;
+	uint16_t dgpu_power = 0;
+
+	apu_power = metrics->ApuPower;
+	apu_limit = metrics->StapmOriginalLimit;
+	if (apu_power > apu_limit && apu_limit != 0)
+		apu_boost =  ((apu_power - apu_limit) * 100) / apu_limit;
+	apu_boost = (apu_boost > 100) ? 100 : apu_boost;
+
+	dgpu_power = metrics->dGpuPower;
+	if (metrics->StapmCurrentLimit > metrics->StapmOriginalLimit)
+		dgpu_limit = metrics->StapmCurrentLimit - metrics->StapmOriginalLimit;
+	if (dgpu_power > dgpu_limit && dgpu_limit != 0)
+		dgpu_boost = ((dgpu_power - dgpu_limit) * 100) / dgpu_limit;
+	dgpu_boost = (dgpu_boost > 100) ? 100 : dgpu_boost;
+
+	if (dgpu_boost >= apu_boost)
+		apu_boost = 0;
+	else
+		dgpu_boost = 0;
+
+	*apu_percent = apu_boost;
+	*dgpu_percent = dgpu_boost;
+}
+
+
 static int renoir_get_smu_metrics_data(struct smu_context *smu,
 				       MetricsMember_t member,
 				       uint32_t *value)
@@ -1135,6 +1169,9 @@
 
 	SmuMetrics_t *metrics = (SmuMetrics_t *)smu_table->metrics_table;
 	int ret = 0;
+	uint32_t apu_percent = 0;
+	uint32_t dgpu_percent = 0;
+
 
 	mutex_lock(&smu->metrics_lock);
 
@@ -1183,26 +1220,18 @@
 		*value = metrics->Voltage[1];
 		break;
 	case METRICS_SS_APU_SHARE:
-		/* return the percentage of APU power with respect to APU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of APU power boost
+		 * with respect to APU's power limit.
 		 */
-		if (metrics->StapmOriginalLimit > 0)
-			*value =  (metrics->ApuPower * 100) / metrics->StapmOriginalLimit;
-		else
-			*value = 0;
+		renoir_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = apu_percent;
 		break;
 	case METRICS_SS_DGPU_SHARE:
-		/* return the percentage of dGPU power with respect to dGPU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of dGPU power boost
+		 * with respect to dGPU's power limit.
 		 */
-		if ((metrics->dGpuPower > 0) &&
-		    (metrics->StapmCurrentLimit > metrics->StapmOriginalLimit))
-			*value = (metrics->dGpuPower * 100) /
-				  (metrics->StapmCurrentLimit - metrics->StapmOriginalLimit);
-		else
-			*value = 0;
+		renoir_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = dgpu_percent;
 		break;
 	default:
 		*value = UINT_MAX;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu12/smu_v12_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu12/smu_v12_0.c
@@ -120,7 +120,8 @@
 
 int smu_v12_0_set_gfx_cgpg(struct smu_context *smu, bool enable)
 {
-	if (!(smu->adev->pg_flags & AMD_PG_SUPPORT_GFX_PG))
+	/* Until now the SMU12 only implemented for Renoir series so here neen't do APU check. */
+	if (!(smu->adev->pg_flags & AMD_PG_SUPPORT_GFX_PG) || smu->adev->in_s0ix)
 		return 0;
 
 	return smu_cmn_send_smc_msg_with_param(smu,
@@ -191,6 +192,9 @@
 	kfree(smu_table->watermarks_table);
 	smu_table->watermarks_table = NULL;
 
+	kfree(smu_table->gpu_metrics_table);
+	smu_table->gpu_metrics_table = NULL;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu13/aldebaran_ppt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu13/aldebaran_ppt.c
@@ -1619,7 +1619,7 @@
 {
 	return smu_cmn_send_smc_msg_with_param(smu,
 					       SMU_MSG_GmiPwrDnControl,
-					       en ? 1 : 0,
+					       en ? 0 : 1,
 					       NULL);
 }
 
@@ -1627,6 +1627,7 @@
 	uint32_t feature_mask;
 	const char *label;
 } logging_label[] = {
+	{(1U << THROTTLER_TEMP_GPU_BIT), "GPU"},
 	{(1U << THROTTLER_TEMP_MEM_BIT), "HBM"},
 	{(1U << THROTTLER_TEMP_VR_GFX_BIT), "VR of GFX rail"},
 	{(1U << THROTTLER_TEMP_VR_MEM_BIT), "VR of HBM rail"},
@@ -1710,7 +1711,6 @@
 
 	gpu_metrics->average_gfx_activity = metrics.AverageGfxActivity;
 	gpu_metrics->average_umc_activity = metrics.AverageUclkActivity;
-	gpu_metrics->average_mm_activity = 0;
 
 	/* Valid power data is available only from primary die */
 	if (aldebaran_is_primary(smu)) {
@@ -1774,7 +1774,8 @@
 
 	index = smu_cmn_to_asic_specific_index(smu, CMN2ASIC_MAPPING_MSG,
 						SMU_MSG_GfxDeviceDriverReset);
-
+	if (index < 0 )
+		return -EINVAL;
 	mutex_lock(&smu->message_lock);
 	if (smu_version >= 0x00441400) {
 		ret = smu_cmn_send_msg_without_waiting(smu, (uint16_t)index, SMU_RESET_MODE_2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0.c
@@ -69,8 +69,8 @@
 #define PCIE_LC_LINK_WIDTH_CNTL__LC_LINK_WIDTH_RD_MASK 0x00000070L
 #define PCIE_LC_LINK_WIDTH_CNTL__LC_LINK_WIDTH_RD__SHIFT 0x4
 #define smnPCIE_LC_SPEED_CNTL			0x11140290
-#define PCIE_LC_SPEED_CNTL__LC_CURRENT_DATA_RATE_MASK 0xC000
-#define PCIE_LC_SPEED_CNTL__LC_CURRENT_DATA_RATE__SHIFT 0xE
+#define PCIE_LC_SPEED_CNTL__LC_CURRENT_DATA_RATE_MASK 0xE0
+#define PCIE_LC_SPEED_CNTL__LC_CURRENT_DATA_RATE__SHIFT 0x5
 
 static const int link_width[] = {0, 1, 2, 4, 8, 12, 16};
 static const int link_speed[] = {25, 50, 80, 160};
@@ -197,6 +197,7 @@
 
 int smu_v13_0_check_fw_version(struct smu_context *smu)
 {
+	struct amdgpu_device *adev = smu->adev;
 	uint32_t if_version = 0xff, smu_version = 0xff;
 	uint16_t smu_major;
 	uint8_t smu_minor, smu_debug;
@@ -209,6 +210,8 @@
 	smu_major = (smu_version >> 16) & 0xffff;
 	smu_minor = (smu_version >> 8) & 0xff;
 	smu_debug = (smu_version >> 0) & 0xff;
+	if (smu->is_apu)
+		adev->pm.fw_version = smu_version;
 
 	switch (smu->adev->asic_type) {
 	case CHIP_ALDEBARAN:
@@ -453,11 +456,11 @@
 	if (smu_power->power_context || smu_power->power_context_size != 0)
 		return -EINVAL;
 
-	smu_power->power_context = kzalloc(sizeof(struct smu_13_0_dpm_context),
+	smu_power->power_context = kzalloc(sizeof(struct smu_13_0_power_context),
 					   GFP_KERNEL);
 	if (!smu_power->power_context)
 		return -ENOMEM;
-	smu_power->power_context_size = sizeof(struct smu_13_0_dpm_context);
+	smu_power->power_context_size = sizeof(struct smu_13_0_power_context);
 
 	return 0;
 }
@@ -718,7 +721,7 @@
 	if (bitmap_empty(feature->allowed, SMU_FEATURE_MAX) || feature->feature_num < 64)
 		goto failed;
 
-	bitmap_copy((unsigned long *)feature_mask, feature->allowed, 64);
+	bitmap_to_arr32(feature_mask, feature->allowed, 64);
 
 	ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_SetAllowedFeaturesMaskHigh,
 					      feature_mask[1], NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/amd/pm/swsmu/smu13/yellow_carp_ppt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/amd/pm/swsmu/smu13/yellow_carp_ppt.c
@@ -291,14 +291,9 @@
 
 static int yellow_carp_mode_reset(struct smu_context *smu, int type)
 {
-	int ret = 0, index = 0;
-
-	index = smu_cmn_to_asic_specific_index(smu, CMN2ASIC_MAPPING_MSG,
-				SMU_MSG_GfxDeviceDriverReset);
-	if (index < 0)
-		return index == -EACCES ? 0 : index;
+	int ret = 0;
 
-	ret = smu_cmn_send_smc_msg_with_param(smu, (uint16_t)index, type, NULL);
+	ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_GfxDeviceDriverReset, type, NULL);
 	if (ret)
 		dev_err(smu->adev->dev, "Failed to mode reset!\n");
 
@@ -310,6 +305,42 @@
 	return yellow_carp_mode_reset(smu, SMU_RESET_MODE_2);
 }
 
+
+static void yellow_carp_get_ss_power_percent(SmuMetrics_t *metrics,
+					uint32_t *apu_percent, uint32_t *dgpu_percent)
+{
+	uint32_t apu_boost = 0;
+	uint32_t dgpu_boost = 0;
+	uint16_t apu_limit = 0;
+	uint16_t dgpu_limit = 0;
+	uint16_t apu_power = 0;
+	uint16_t dgpu_power = 0;
+
+	/* APU and dGPU power values are reported in milli Watts
+	 * and STAPM power limits are in Watts */
+	apu_power = metrics->ApuPower/1000;
+	apu_limit = metrics->StapmOpnLimit;
+	if (apu_power > apu_limit && apu_limit != 0)
+		apu_boost =  ((apu_power - apu_limit) * 100) / apu_limit;
+	apu_boost = (apu_boost > 100) ? 100 : apu_boost;
+
+	dgpu_power = metrics->dGpuPower/1000;
+	if (metrics->StapmCurrentLimit > metrics->StapmOpnLimit)
+		dgpu_limit = metrics->StapmCurrentLimit - metrics->StapmOpnLimit;
+	if (dgpu_power > dgpu_limit && dgpu_limit != 0)
+		dgpu_boost = ((dgpu_power - dgpu_limit) * 100) / dgpu_limit;
+	dgpu_boost = (dgpu_boost > 100) ? 100 : dgpu_boost;
+
+	if (dgpu_boost >= apu_boost)
+		apu_boost = 0;
+	else
+		dgpu_boost = 0;
+
+	*apu_percent = apu_boost;
+	*dgpu_percent = dgpu_boost;
+
+}
+
 static int yellow_carp_get_smu_metrics_data(struct smu_context *smu,
 							MetricsMember_t member,
 							uint32_t *value)
@@ -318,6 +349,8 @@
 
 	SmuMetrics_t *metrics = (SmuMetrics_t *)smu_table->metrics_table;
 	int ret = 0;
+	uint32_t apu_percent = 0;
+	uint32_t dgpu_percent = 0;
 
 	mutex_lock(&smu->metrics_lock);
 
@@ -370,26 +403,18 @@
 		*value = metrics->Voltage[1];
 		break;
 	case METRICS_SS_APU_SHARE:
-		/* return the percentage of APU power with respect to APU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of APU power boost
+		 * with respect to APU's power limit.
 		 */
-		if (metrics->StapmOpnLimit > 0)
-			*value =  (metrics->ApuPower * 100) / metrics->StapmOpnLimit;
-		else
-			*value = 0;
+		yellow_carp_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = apu_percent;
 		break;
 	case METRICS_SS_DGPU_SHARE:
-		/* return the percentage of dGPU power with respect to dGPU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of dGPU power boost
+		 * with respect to dGPU's power limit.
 		 */
-		if ((metrics->dGpuPower > 0) &&
-		    (metrics->StapmCurrentLimit > metrics->StapmOpnLimit))
-			*value = (metrics->dGpuPower * 100) /
-				  (metrics->StapmCurrentLimit - metrics->StapmOpnLimit);
-		else
-			*value = 0;
+		yellow_carp_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = dgpu_percent;
 		break;
 	default:
 		*value = UINT_MAX;
@@ -1049,7 +1074,7 @@
 static int yellow_carp_print_clk_levels(struct smu_context *smu,
 				enum smu_clk_type clk_type, char *buf)
 {
-	int i, size = 0, ret = 0;
+	int i, idx, size = 0, ret = 0;
 	uint32_t cur_value = 0, value = 0, count = 0;
 
 	smu_cmn_get_sysfs_buf(&buf, &size);
@@ -1081,7 +1106,8 @@
 			goto print_clk_out;
 
 		for (i = 0; i < count; i++) {
-			ret = yellow_carp_get_dpm_freq_by_index(smu, clk_type, i, &value);
+			idx = (clk_type == SMU_FCLK || clk_type == SMU_MCLK) ? (count - i - 1) : i;
+			ret = yellow_carp_get_dpm_freq_by_index(smu, clk_type, idx, &value);
 			if (ret)
 				goto print_clk_out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/display/komeda/komeda_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/display/komeda/komeda_crtc.c
@@ -235,7 +235,7 @@
 			crtc->state->event = NULL;
 			drm_crtc_send_vblank_event(crtc, event);
 		} else {
-			DRM_WARN("CRTC[%d]: FLIP happen but no pending commit.\n",
+			DRM_WARN("CRTC[%d]: FLIP happened but no pending commit.\n",
 				 drm_crtc_index(&kcrtc->base));
 		}
 		spin_unlock_irqrestore(&crtc->dev->event_lock, flags);
@@ -286,7 +286,7 @@
 	komeda_crtc_do_flush(crtc, old);
 }
 
-static void
+void
 komeda_crtc_flush_and_wait_for_flip_done(struct komeda_crtc *kcrtc,
 					 struct completion *input_flip_done)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/display/komeda/komeda_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/display/komeda/komeda_kms.c
@@ -69,6 +69,25 @@
 	.minor = 1,
 };
 
+static void komeda_kms_atomic_commit_hw_done(struct drm_atomic_state *state)
+{
+	struct drm_device *dev = state->dev;
+	struct komeda_kms_dev *kms = to_kdev(dev);
+	int i;
+
+	for (i = 0; i < kms->n_crtcs; i++) {
+		struct komeda_crtc *kcrtc = &kms->crtcs[i];
+
+		if (kcrtc->base.state->active) {
+			struct completion *flip_done = NULL;
+			if (kcrtc->base.state->event)
+				flip_done = kcrtc->base.state->event->base.completion;
+			komeda_crtc_flush_and_wait_for_flip_done(kcrtc, flip_done);
+		}
+	}
+	drm_atomic_helper_commit_hw_done(state);
+}
+
 static void komeda_kms_commit_tail(struct drm_atomic_state *old_state)
 {
 	struct drm_device *dev = old_state->dev;
@@ -81,7 +100,7 @@
 
 	drm_atomic_helper_commit_modeset_enables(dev, old_state);
 
-	drm_atomic_helper_commit_hw_done(old_state);
+	komeda_kms_atomic_commit_hw_done(old_state);
 
 	drm_atomic_helper_wait_for_flip_done(dev, old_state);
 
@@ -144,6 +163,7 @@
 	struct drm_plane *plane;
 	struct list_head zorder_list;
 	int order = 0, err;
+	u32 slave_zpos = 0;
 
 	DRM_DEBUG_ATOMIC("[CRTC:%d:%s] calculating normalized zpos values\n",
 			 crtc->base.id, crtc->name);
@@ -183,10 +203,13 @@
 				 plane_st->zpos, plane_st->normalized_zpos);
 
 		/* calculate max slave zorder */
-		if (has_bit(drm_plane_index(plane), kcrtc->slave_planes))
+		if (has_bit(drm_plane_index(plane), kcrtc->slave_planes)) {
+			slave_zpos = plane_st->normalized_zpos;
+			if (to_kplane_st(plane_st)->layer_split)
+				slave_zpos++;
 			kcrtc_st->max_slave_zorder =
-				max(plane_st->normalized_zpos,
-				    kcrtc_st->max_slave_zorder);
+				max(slave_zpos, kcrtc_st->max_slave_zorder);
+		}
 	}
 
 	crtc_st->zpos_changed = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/display/komeda/komeda_kms.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/display/komeda/komeda_kms.h
@@ -182,6 +182,8 @@
 
 void komeda_crtc_handle_event(struct komeda_crtc   *kcrtc,
 			      struct komeda_events *evts);
+void komeda_crtc_flush_and_wait_for_flip_done(struct komeda_crtc *kcrtc,
+					      struct completion *input_flip_done);
 
 struct komeda_kms_dev *komeda_kms_attach(struct komeda_dev *mdev);
 void komeda_kms_detach(struct komeda_kms_dev *kms);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/display/komeda/komeda_pipeline_state.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/display/komeda/komeda_pipeline_state.c
@@ -259,7 +259,7 @@
 	u32 avail_scalers;
 
 	pipe_st = komeda_pipeline_get_state(c->pipeline, state);
-	if (!pipe_st)
+	if (IS_ERR_OR_NULL(pipe_st))
 		return NULL;
 
 	avail_scalers = (pipe_st->active_comps & KOMEDA_PIPELINE_SCALERS) ^
@@ -1223,7 +1223,7 @@
 	return 0;
 }
 
-static void
+static int
 komeda_pipeline_unbound_components(struct komeda_pipeline *pipe,
 				   struct komeda_pipeline_state *new)
 {
@@ -1243,8 +1243,12 @@
 		c = komeda_pipeline_get_component(pipe, id);
 		c_st = komeda_component_get_state_and_set_user(c,
 				drm_st, NULL, new->crtc);
+		if (PTR_ERR(c_st) == -EDEADLK)
+			return -EDEADLK;
 		WARN_ON(IS_ERR(c_st));
 	}
+
+	return 0;
 }
 
 /* release unclaimed pipeline resource */
@@ -1266,9 +1270,8 @@
 	if (WARN_ON(IS_ERR_OR_NULL(st)))
 		return -EINVAL;
 
-	komeda_pipeline_unbound_components(pipe, st);
+	return komeda_pipeline_unbound_components(pipe, st);
 
-	return 0;
 }
 
 /* Since standalong disabled components must be disabled separately and in the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/display/komeda/komeda_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/display/komeda/komeda_plane.c
@@ -265,6 +265,10 @@
 
 	formats = komeda_get_layer_fourcc_list(&mdev->fmt_tbl,
 					       layer->layer_type, &n_formats);
+	if (!formats) {
+		kfree(kplane);
+		return -ENOMEM;
+	}
 
 	err = drm_universal_plane_init(&kms->base, plane,
 			get_possible_crtcs(kms, c->pipeline),
@@ -275,8 +279,10 @@
 
 	komeda_put_fourcc_list(formats);
 
-	if (err)
-		goto cleanup;
+	if (err) {
+		kfree(kplane);
+		return err;
+	}
 
 	drm_plane_helper_add(plane, &komeda_plane_helper_funcs);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/display/komeda/komeda_wb_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/display/komeda/komeda_wb_connector.c
@@ -160,6 +160,10 @@
 	formats = komeda_get_layer_fourcc_list(&mdev->fmt_tbl,
 					       kwb_conn->wb_layer->layer_type,
 					       &n_formats);
+	if (!formats) {
+		kfree(kwb_conn);
+		return -ENOMEM;
+	}
 
 	err = drm_writeback_connector_init(&kms->base, wb_conn,
 					   &komeda_wb_connector_funcs,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/malidp_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/malidp_crtc.c
@@ -487,7 +487,10 @@
 	if (crtc->state)
 		malidp_crtc_destroy_state(crtc, crtc->state);
 
-	__drm_atomic_helper_crtc_reset(crtc, &state->base);
+	if (state)
+		__drm_atomic_helper_crtc_reset(crtc, &state->base);
+	else
+		__drm_atomic_helper_crtc_reset(crtc, NULL);
 }
 
 static int malidp_crtc_enable_vblank(struct drm_crtc *crtc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/malidp_mw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/malidp_mw.c
@@ -70,7 +70,10 @@
 		__drm_atomic_helper_connector_destroy_state(connector->state);
 
 	kfree(connector->state);
-	__drm_atomic_helper_connector_reset(connector, &mw_state->base);
+	connector->state = NULL;
+
+	if (mw_state)
+		__drm_atomic_helper_connector_reset(connector, &mw_state->base);
 }
 
 static enum drm_connector_status
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/arm/malidp_planes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/arm/malidp_planes.c
@@ -348,7 +348,7 @@
 		else
 			sgt = obj->funcs->get_sg_table(obj);
 
-		if (!sgt)
+		if (IS_ERR(sgt))
 			return false;
 
 		sgl = sgt->sgl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/armada/armada_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/armada/armada_drv.c
@@ -99,7 +99,6 @@
 	if (ret) {
 		dev_err(dev, "[" DRM_NAME ":%s] can't kick out simple-fb: %d\n",
 			__func__, ret);
-		kfree(priv);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/armada/armada_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/armada/armada_gem.c
@@ -336,7 +336,7 @@
 	struct drm_armada_gem_pwrite *args = data;
 	struct armada_gem_object *dobj;
 	char __user *ptr;
-	int ret;
+	int ret = 0;
 
 	DRM_DEBUG_DRIVER("handle %u off %u size %u ptr 0x%llx\n",
 		args->handle, args->offset, args->size, args->ptr);
@@ -349,9 +349,8 @@
 	if (!access_ok(ptr, args->size))
 		return -EFAULT;
 
-	ret = fault_in_pages_readable(ptr, args->size);
-	if (ret)
-		return ret;
+	if (fault_in_readable(ptr, args->size))
+		return -EFAULT;
 
 	dobj = armada_gem_object_lookup(file, args->handle);
 	if (dobj == NULL)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/armada/armada_overlay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/armada/armada_overlay.c
@@ -4,6 +4,8 @@
  *  Rewritten from the dovefb driver, and Armada510 manuals.
  */
 
+#include <linux/bitfield.h>
+
 #include <drm/armada_drm.h>
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_helper.h>
@@ -451,8 +453,8 @@
 			     drm_to_overlay_state(state)->colorkey_ug,
 			     drm_to_overlay_state(state)->colorkey_vb, 0);
 	} else if (property == priv->colorkey_mode_prop) {
-		*val = (drm_to_overlay_state(state)->colorkey_mode &
-			CFG_CKMODE_MASK) >> ffs(CFG_CKMODE_MASK);
+		*val = FIELD_GET(CFG_CKMODE_MASK,
+				 drm_to_overlay_state(state)->colorkey_mode);
 	} else if (property == priv->brightness_prop) {
 		*val = drm_to_overlay_state(state)->brightness + 256;
 	} else if (property == priv->contrast_prop) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/aspeed/aspeed_gfx_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/aspeed/aspeed_gfx_drv.c
@@ -291,7 +291,7 @@
 	if (rc)
 		return rc;
 
-	return sprintf(buf, "%u\n", reg & 1);
+	return sprintf(buf, "%u\n", reg);
 }
 static DEVICE_ATTR_RO(vga_pw);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ast/ast_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ast/ast_main.c
@@ -423,11 +423,12 @@
 		return ERR_PTR(-EIO);
 
 	/*
-	 * If we don't have IO space at all, use MMIO now and
-	 * assume the chip has MMIO enabled by default (rev 0x20
-	 * and higher).
+	 * After AST2500, MMIO is enabled by default, and it should be adopted
+	 * to be compatible with Arm.
 	 */
-	if (!(pci_resource_flags(pdev, 2) & IORESOURCE_IO)) {
+	if (pdev->revision >= 0x40) {
+		ast->ioregs = ast->regs + AST_IO_MM_OFFSET;
+	} else if (!(pci_resource_flags(pdev, 2) & IORESOURCE_IO)) {
 		drm_info(dev, "platform has no IO space, trying MMIO\n");
 		ast->ioregs = ast->regs + AST_IO_MM_OFFSET;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ast/ast_mode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ast/ast_mode.c
@@ -474,7 +474,10 @@
 static void ast_set_crtthd_reg(struct ast_private *ast)
 {
 	/* Set Threshold */
-	if (ast->chip == AST2300 || ast->chip == AST2400 ||
+	if (ast->chip == AST2600) {
+		ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xa7, 0xe0);
+		ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xa6, 0xa0);
+	} else if (ast->chip == AST2300 || ast->chip == AST2400 ||
 	    ast->chip == AST2500) {
 		ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xa7, 0x78);
 		ast_set_index_reg(ast, AST_IO_CRTC_PORT, 0xa6, 0x60);
@@ -1121,7 +1124,10 @@
 	if (crtc->state)
 		crtc->funcs->atomic_destroy_state(crtc, crtc->state);
 
-	__drm_atomic_helper_crtc_reset(crtc, &ast_state->base);
+	if (ast_state)
+		__drm_atomic_helper_crtc_reset(crtc, &ast_state->base);
+	else
+		__drm_atomic_helper_crtc_reset(crtc, NULL);
 }
 
 static struct drm_crtc_state *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ast/ast_post.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ast/ast_post.c
@@ -291,7 +291,7 @@
 				;
 			} while (ast_read32(ast, 0x10100) != 0xa8);
 		} else {/* AST2100/1100 */
-			if (ast->chip == AST2100 || ast->chip == 2200)
+			if (ast->chip == AST2100 || ast->chip == AST2200)
 				dram_reg_info = ast2100_dram_table_data;
 			else
 				dram_reg_info = ast1100_dram_table_data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ast/ast_tables.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ast/ast_tables.h
@@ -282,8 +282,6 @@
 };
 
 static const struct ast_vbios_enhtable res_1600x900[] = {
-	{1800, 1600, 24, 80, 1000,  900, 1, 3, VCLK108,		/* 60Hz */
-	 (SyncPP | Charx8Dot | LineCompareOff | WideScreenMode | NewModeInfo), 60, 3, 0x3A },
 	{1760, 1600, 48, 32, 926, 900, 3, 5, VCLK97_75,		/* 60Hz CVT RB */
 	 (SyncNP | Charx8Dot | LineCompareOff | WideScreenMode | NewModeInfo |
 	  AST2500PreCatchCRT), 60, 1, 0x3A },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/Kconfig
@@ -8,7 +8,6 @@
 config DRM_PANEL_BRIDGE
 	def_bool y
 	depends on DRM_BRIDGE
-	depends on DRM_KMS_HELPER
 	select DRM_PANEL
 	help
 	  DRM bridge wrapper of DRM panels
@@ -30,6 +29,7 @@
 config DRM_CHIPONE_ICN6211
 	tristate "Chipone ICN6211 MIPI-DSI/RGB Converter bridge"
 	depends on OF
+	select DRM_KMS_HELPER
 	select DRM_MIPI_DSI
 	select DRM_PANEL_BRIDGE
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/adv7511/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/adv7511/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
-adv7511-y := adv7511_drv.o adv7533.o
-adv7511-$(CONFIG_DRM_I2C_ADV7511_AUDIO) += adv7511_audio.o
-adv7511-$(CONFIG_DRM_I2C_ADV7511_CEC) += adv7511_cec.o
-obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511.o
+adv7511_drm-y := adv7511_drv.o adv7533.o
+adv7511_drm-$(CONFIG_DRM_I2C_ADV7511_AUDIO) += adv7511_audio.o
+adv7511_drm-$(CONFIG_DRM_I2C_ADV7511_CEC) += adv7511_cec.o
+obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511_drm.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/adv7511/adv7511.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/adv7511/adv7511.h
@@ -169,6 +169,7 @@
 #define ADV7511_PACKET_ENABLE_SPARE2		BIT(1)
 #define ADV7511_PACKET_ENABLE_SPARE1		BIT(0)
 
+#define ADV7535_REG_POWER2_HPD_OVERRIDE		BIT(6)
 #define ADV7511_REG_POWER2_HPD_SRC_MASK		0xc0
 #define ADV7511_REG_POWER2_HPD_SRC_BOTH		0x00
 #define ADV7511_REG_POWER2_HPD_SRC_HPD		0x40
@@ -386,10 +387,7 @@
 #else
 static inline int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511)
 {
-	unsigned int offset = adv7511->type == ADV7533 ?
-						ADV7533_REG_CEC_OFFSET : 0;
-
-	regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL + offset,
+	regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL,
 		     ADV7511_CEC_CTRL_POWER_DOWN);
 	return 0;
 }
@@ -397,7 +395,8 @@
 
 void adv7533_dsi_power_on(struct adv7511 *adv);
 void adv7533_dsi_power_off(struct adv7511 *adv);
-void adv7533_mode_set(struct adv7511 *adv, const struct drm_display_mode *mode);
+enum drm_mode_status adv7533_mode_valid(struct adv7511 *adv,
+					const struct drm_display_mode *mode);
 int adv7533_patch_registers(struct adv7511 *adv);
 int adv7533_patch_cec_registers(struct adv7511 *adv);
 int adv7533_attach_dsi(struct adv7511 *adv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
@@ -153,7 +153,16 @@
 			   ADV7511_AUDIO_CFG3_LEN_MASK, len);
 	regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG,
 			   ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4);
-	regmap_write(adv7511->regmap, 0x73, 0x1);
+
+	/* send current Audio infoframe values while updating */
+	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
+			   BIT(5), BIT(5));
+
+	regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1);
+
+	/* use Audio infoframe updated info */
+	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
+			   BIT(5), 0);
 
 	return 0;
 }
@@ -184,8 +193,9 @@
 	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0),
 				BIT(7) | BIT(6), BIT(7));
 	/* use Audio infoframe updated info */
-	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1),
+	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
 				BIT(5), 0);
+
 	/* enable SPDIF receiver */
 	if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF)
 		regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/adv7511/adv7511_cec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/adv7511/adv7511_cec.c
@@ -316,7 +316,7 @@
 		goto err_cec_alloc;
 	}
 
-	regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL + offset, 0);
+	regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL, 0);
 	/* cec soft reset */
 	regmap_write(adv7511->regmap_cec,
 		     ADV7511_REG_CEC_SOFT_RESET + offset, 0x01);
@@ -343,7 +343,7 @@
 	dev_info(dev, "Initializing CEC failed with error %d, disabling CEC\n",
 		 ret);
 err_cec_parse_dt:
-	regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL + offset,
+	regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL,
 		     ADV7511_CEC_CTRL_POWER_DOWN);
 	return ret == -EPROBE_DEFER ? ret : 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
@@ -351,11 +351,17 @@
 	 * from standby or are enabled. When the HPD goes low the adv7511 is
 	 * reset and the outputs are disabled which might cause the monitor to
 	 * go to standby again. To avoid this we ignore the HPD pin for the
-	 * first few seconds after enabling the output.
+	 * first few seconds after enabling the output. On the other hand
+	 * adv7535 require to enable HPD Override bit for proper HPD.
 	 */
-	regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
-			   ADV7511_REG_POWER2_HPD_SRC_MASK,
-			   ADV7511_REG_POWER2_HPD_SRC_NONE);
+	if (adv7511->type == ADV7535)
+		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+				   ADV7535_REG_POWER2_HPD_OVERRIDE,
+				   ADV7535_REG_POWER2_HPD_OVERRIDE);
+	else
+		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+				   ADV7511_REG_POWER2_HPD_SRC_MASK,
+				   ADV7511_REG_POWER2_HPD_SRC_NONE);
 }
 
 static void adv7511_power_on(struct adv7511 *adv7511)
@@ -375,6 +381,10 @@
 static void __adv7511_power_off(struct adv7511 *adv7511)
 {
 	/* TODO: setup additional power down modes */
+	if (adv7511->type == ADV7535)
+		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+				   ADV7535_REG_POWER2_HPD_OVERRIDE, 0);
+
 	regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
 			   ADV7511_POWER_POWER_DOWN,
 			   ADV7511_POWER_POWER_DOWN);
@@ -672,9 +682,14 @@
 			status = connector_status_disconnected;
 	} else {
 		/* Renable HPD sensing */
-		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
-				   ADV7511_REG_POWER2_HPD_SRC_MASK,
-				   ADV7511_REG_POWER2_HPD_SRC_BOTH);
+		if (adv7511->type == ADV7535)
+			regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+					   ADV7535_REG_POWER2_HPD_OVERRIDE,
+					   ADV7535_REG_POWER2_HPD_OVERRIDE);
+		else
+			regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+					   ADV7511_REG_POWER2_HPD_SRC_MASK,
+					   ADV7511_REG_POWER2_HPD_SRC_BOTH);
 	}
 
 	adv7511->status = status;
@@ -682,7 +697,7 @@
 }
 
 static enum drm_mode_status adv7511_mode_valid(struct adv7511 *adv7511,
-			      struct drm_display_mode *mode)
+			      const struct drm_display_mode *mode)
 {
 	if (mode->clock > 165000)
 		return MODE_CLOCK_HIGH;
@@ -771,14 +786,16 @@
 	else
 		low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE;
 
-	regmap_update_bits(adv7511->regmap, 0xfb,
-		0x6, low_refresh_rate << 1);
+	if (adv7511->type == ADV7511)
+		regmap_update_bits(adv7511->regmap, 0xfb,
+				   0x6, low_refresh_rate << 1);
+	else
+		regmap_update_bits(adv7511->regmap, 0x4a,
+				   0xc, low_refresh_rate << 2);
+
 	regmap_update_bits(adv7511->regmap, 0x17,
 		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
 
-	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
-		adv7533_mode_set(adv7511, adj_mode);
-
 	drm_mode_copy(&adv7511->curr_mode, adj_mode);
 
 	/*
@@ -898,6 +915,18 @@
 	adv7511_mode_set(adv, mode, adj_mode);
 }
 
+static enum drm_mode_status adv7511_bridge_mode_valid(struct drm_bridge *bridge,
+						      const struct drm_display_info *info,
+		const struct drm_display_mode *mode)
+{
+	struct adv7511 *adv = bridge_to_adv7511(bridge);
+
+	if (adv->type == ADV7533 || adv->type == ADV7535)
+		return adv7533_mode_valid(adv, mode);
+	else
+		return adv7511_mode_valid(adv, mode);
+}
+
 static int adv7511_bridge_attach(struct drm_bridge *bridge,
 				 enum drm_bridge_attach_flags flags)
 {
@@ -948,6 +977,7 @@
 	.enable = adv7511_bridge_enable,
 	.disable = adv7511_bridge_disable,
 	.mode_set = adv7511_bridge_mode_set,
+	.mode_valid = adv7511_bridge_mode_valid,
 	.attach = adv7511_bridge_attach,
 	.detect = adv7511_bridge_detect,
 	.get_edid = adv7511_bridge_get_edid,
@@ -1048,6 +1078,10 @@
 						ADV7511_CEC_I2C_ADDR_DEFAULT);
 	if (IS_ERR(adv->i2c_cec))
 		return PTR_ERR(adv->i2c_cec);
+
+	regmap_write(adv->regmap, ADV7511_REG_CEC_I2C_ADDR,
+		     adv->i2c_cec->addr << 1);
+
 	i2c_set_clientdata(adv->i2c_cec, adv);
 
 	adv->regmap_cec = devm_regmap_init_i2c(adv->i2c_cec,
@@ -1252,9 +1286,6 @@
 	if (ret)
 		goto err_i2c_unregister_packet;
 
-	regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR,
-		     adv7511->i2c_cec->addr << 1);
-
 	INIT_WORK(&adv7511->hpd_work, adv7511_hpd_work);
 
 	if (i2c->irq) {
@@ -1291,6 +1322,7 @@
 	return 0;
 
 err_unregister_cec:
+	cec_unregister_adapter(adv7511->cec_adap);
 	i2c_unregister_device(adv7511->i2c_cec);
 	clk_disable_unprepare(adv7511->cec_clk);
 err_i2c_unregister_packet:
@@ -1309,8 +1341,6 @@
 
 	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
 		adv7533_detach_dsi(adv7511);
-	i2c_unregister_device(adv7511->i2c_cec);
-	clk_disable_unprepare(adv7511->cec_clk);
 
 	adv7511_uninit_regulators(adv7511);
 
@@ -1319,6 +1349,8 @@
 	adv7511_audio_exit(adv7511);
 
 	cec_unregister_adapter(adv7511->cec_adap);
+	i2c_unregister_device(adv7511->i2c_cec);
+	clk_disable_unprepare(adv7511->cec_clk);
 
 	i2c_unregister_device(adv7511->i2c_packet);
 	i2c_unregister_device(adv7511->i2c_edid);
@@ -1362,10 +1394,21 @@
 
 static int __init adv7511_init(void)
 {
-	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
-		mipi_dsi_driver_register(&adv7533_dsi_driver);
+	int ret;
+
+	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) {
+		ret = mipi_dsi_driver_register(&adv7533_dsi_driver);
+		if (ret)
+			return ret;
+	}
 
-	return i2c_add_driver(&adv7511_driver);
+	ret = i2c_add_driver(&adv7511_driver);
+	if (ret) {
+		if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
+			mipi_dsi_driver_unregister(&adv7533_dsi_driver);
+	}
+
+	return ret;
 }
 module_init(adv7511_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/adv7511/adv7533.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/adv7511/adv7533.c
@@ -100,26 +100,24 @@
 	regmap_write(adv->regmap_cec, 0x27, 0x0b);
 }
 
-void adv7533_mode_set(struct adv7511 *adv, const struct drm_display_mode *mode)
+enum drm_mode_status adv7533_mode_valid(struct adv7511 *adv,
+					const struct drm_display_mode *mode)
 {
+	unsigned long max_lane_freq;
 	struct mipi_dsi_device *dsi = adv->dsi;
-	int lanes, ret;
+	u8 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
 
-	if (adv->num_dsi_lanes != 4)
-		return;
+	/* Check max clock for either 7533 or 7535 */
+	if (mode->clock > (adv->type == ADV7533 ? 80000 : 148500))
+		return MODE_CLOCK_HIGH;
 
-	if (mode->clock > 80000)
-		lanes = 4;
-	else
-		lanes = 3;
-
-	if (lanes != dsi->lanes) {
-		mipi_dsi_detach(dsi);
-		dsi->lanes = lanes;
-		ret = mipi_dsi_attach(dsi);
-		if (ret)
-			dev_err(&dsi->dev, "failed to change host lanes\n");
-	}
+	/* Check max clock for each lane */
+	max_lane_freq = (adv->type == ADV7533 ? 800000 : 891000);
+
+	if (mode->clock * bpp > max_lane_freq * adv->num_dsi_lanes)
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
 }
 
 int adv7533_patch_registers(struct adv7511 *adv)
@@ -193,7 +191,7 @@
 
 	of_property_read_u32(np, "adi,dsi-lanes", &num_lanes);
 
-	if (num_lanes < 1 || num_lanes > 4)
+	if (num_lanes < 2 || num_lanes > 4)
 		return -EINVAL;
 
 	adv->num_dsi_lanes = num_lanes;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -1269,6 +1269,25 @@
 }
 
 static
+struct drm_crtc *analogix_dp_get_old_crtc(struct analogix_dp_device *dp,
+					  struct drm_atomic_state *state)
+{
+	struct drm_encoder *encoder = dp->encoder;
+	struct drm_connector *connector;
+	struct drm_connector_state *conn_state;
+
+	connector = drm_atomic_get_old_connector_for_encoder(state, encoder);
+	if (!connector)
+		return NULL;
+
+	conn_state = drm_atomic_get_old_connector_state(state, connector);
+	if (!conn_state)
+		return NULL;
+
+	return conn_state->crtc;
+}
+
+static
 struct drm_crtc *analogix_dp_get_new_crtc(struct analogix_dp_device *dp,
 					  struct drm_atomic_state *state)
 {
@@ -1448,14 +1467,16 @@
 {
 	struct drm_atomic_state *old_state = old_bridge_state->base.state;
 	struct analogix_dp_device *dp = bridge->driver_private;
-	struct drm_crtc *crtc;
+	struct drm_crtc *old_crtc, *new_crtc;
+	struct drm_crtc_state *old_crtc_state = NULL;
 	struct drm_crtc_state *new_crtc_state = NULL;
+	int ret;
 
-	crtc = analogix_dp_get_new_crtc(dp, old_state);
-	if (!crtc)
+	new_crtc = analogix_dp_get_new_crtc(dp, old_state);
+	if (!new_crtc)
 		goto out;
 
-	new_crtc_state = drm_atomic_get_new_crtc_state(old_state, crtc);
+	new_crtc_state = drm_atomic_get_new_crtc_state(old_state, new_crtc);
 	if (!new_crtc_state)
 		goto out;
 
@@ -1464,6 +1485,19 @@
 		return;
 
 out:
+	old_crtc = analogix_dp_get_old_crtc(dp, old_state);
+	if (old_crtc) {
+		old_crtc_state = drm_atomic_get_old_crtc_state(old_state,
+							       old_crtc);
+
+		/* When moving from PSR to fully disabled, exit PSR first. */
+		if (old_crtc_state && old_crtc_state->self_refresh_active) {
+			ret = analogix_dp_disable_psr(dp);
+			if (ret)
+				DRM_ERROR("Failed to disable psr (%d)\n", ret);
+		}
+	}
+
 	analogix_dp_bridge_disable(bridge);
 }
 
@@ -1632,8 +1666,19 @@
 				       struct drm_dp_aux_msg *msg)
 {
 	struct analogix_dp_device *dp = to_dp(aux);
+	int ret;
+
+	pm_runtime_get_sync(dp->dev);
+
+	ret = analogix_dp_detect_hpd(dp);
+	if (ret)
+		goto out;
+
+	ret = analogix_dp_transfer(dp, msg);
+out:
+	pm_runtime_put(dp->dev);
 
-	return analogix_dp_transfer(dp, msg);
+	return ret;
 }
 
 struct analogix_dp_device *
@@ -1698,8 +1743,10 @@
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
 	dp->reg_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(dp->reg_base))
-		return ERR_CAST(dp->reg_base);
+	if (IS_ERR(dp->reg_base)) {
+		ret = PTR_ERR(dp->reg_base);
+		goto err_disable_clk;
+	}
 
 	dp->force_hpd = of_property_read_bool(dev->of_node, "force-hpd");
 
@@ -1711,7 +1758,8 @@
 	if (IS_ERR(dp->hpd_gpiod)) {
 		dev_err(dev, "error getting HDP GPIO: %ld\n",
 			PTR_ERR(dp->hpd_gpiod));
-		return ERR_CAST(dp->hpd_gpiod);
+		ret = PTR_ERR(dp->hpd_gpiod);
+		goto err_disable_clk;
 	}
 
 	if (dp->hpd_gpiod) {
@@ -1731,7 +1779,8 @@
 
 	if (dp->irq == -ENXIO) {
 		dev_err(&pdev->dev, "failed to get irq\n");
-		return ERR_PTR(-ENODEV);
+		ret = -ENODEV;
+		goto err_disable_clk;
 	}
 
 	ret = devm_request_threaded_irq(&pdev->dev, dp->irq,
@@ -1740,11 +1789,15 @@
 					irq_flags, "analogix-dp", dp);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to request irq\n");
-		return ERR_PTR(ret);
+		goto err_disable_clk;
 	}
 	disable_irq(dp->irq);
 
 	return dp;
+
+err_disable_clk:
+	clk_disable_unprepare(dp->clock);
+	return ERR_PTR(ret);
 }
 EXPORT_SYMBOL_GPL(analogix_dp_probe);
 
@@ -1807,12 +1860,6 @@
 int analogix_dp_suspend(struct analogix_dp_device *dp)
 {
 	clk_disable_unprepare(dp->clock);
-
-	if (dp->plat_data->panel) {
-		if (drm_panel_unprepare(dp->plat_data->panel))
-			DRM_ERROR("failed to turnoff the panel\n");
-	}
-
 	return 0;
 }
 EXPORT_SYMBOL_GPL(analogix_dp_suspend);
@@ -1827,13 +1874,6 @@
 		return ret;
 	}
 
-	if (dp->plat_data->panel) {
-		if (drm_panel_prepare(dp->plat_data->panel)) {
-			DRM_ERROR("failed to setup the panel\n");
-			return -EBUSY;
-		}
-	}
-
 	return 0;
 }
 EXPORT_SYMBOL_GPL(analogix_dp_resume);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -998,11 +998,21 @@
 	if (!blocking)
 		return 0;
 
+	/*
+	 * db[1]!=0: entering PSR, wait for fully active remote frame buffer.
+	 * db[1]==0: exiting PSR, wait for either
+	 *  (a) ACTIVE_RESYNC - the sink "must display the
+	 *      incoming active frames from the Source device with no visible
+	 *      glitches and/or artifacts", even though timings may still be
+	 *      re-synchronizing; or
+	 *  (b) INACTIVE - the transition is fully complete.
+	 */
 	ret = readx_poll_timeout(analogix_dp_get_psr_status, dp, psr_status,
 		psr_status >= 0 &&
 		((vsc->db[1] && psr_status == DP_PSR_SINK_ACTIVE_RFB) ||
-		(!vsc->db[1] && psr_status == DP_PSR_SINK_INACTIVE)), 1500,
-		DP_TIMEOUT_PSR_LOOP_MS * 1000);
+		(!vsc->db[1] && (psr_status == DP_PSR_SINK_ACTIVE_RESYNC ||
+				 psr_status == DP_PSR_SINK_INACTIVE))),
+		1500, DP_TIMEOUT_PSR_LOOP_MS * 1000);
 	if (ret) {
 		dev_warn(dp->dev, "Failed to apply PSR %d\n", ret);
 		return ret;
@@ -1017,7 +1027,6 @@
 	u32 status_reg;
 	u8 *buffer = msg->buffer;
 	unsigned int i;
-	int num_transferred = 0;
 	int ret;
 
 	/* Buffer size of AUX CH is 16 bytes */
@@ -1069,7 +1078,6 @@
 			reg = buffer[i];
 			writel(reg, dp->reg_base + ANALOGIX_DP_BUF_DATA_0 +
 			       4 * i);
-			num_transferred++;
 		}
 	}
 
@@ -1117,7 +1125,6 @@
 			reg = readl(dp->reg_base + ANALOGIX_DP_BUF_DATA_0 +
 				    4 * i);
 			buffer[i] = (unsigned char)reg;
-			num_transferred++;
 		}
 	}
 
@@ -1134,7 +1141,7 @@
 		 (msg->request & ~DP_AUX_I2C_MOT) == DP_AUX_NATIVE_READ)
 		msg->reply = DP_AUX_NATIVE_REPLY_ACK;
 
-	return num_transferred > 0 ? num_transferred : -EBUSY;
+	return msg->size;
 
 aux_error:
 	/* if aux err happen, reset aux */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -720,7 +720,7 @@
 		ret = sp_tx_aux_rd(ctx, 0xf1);
 
 		if (ret) {
-			sp_tx_rst_aux(ctx);
+			ret = sp_tx_rst_aux(ctx);
 			DRM_DEV_DEBUG_DRIVER(dev, "edid read fail, reset!\n");
 		} else {
 			ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
@@ -735,7 +735,7 @@
 	if (cnt > EDID_TRY_CNT)
 		return -EIO;
 
-	return 0;
+	return ret;
 }
 
 static int segments_edid_read(struct anx7625_data *ctx,
@@ -785,17 +785,18 @@
 	if (cnt > EDID_TRY_CNT)
 		return -EIO;
 
-	return 0;
+	return ret;
 }
 
 static int sp_tx_edid_read(struct anx7625_data *ctx,
 			   u8 *pedid_blocks_buf)
 {
-	u8 offset, edid_pos;
+	u8 offset;
+	int edid_pos;
 	int count, blocks_num;
 	u8 pblock_buf[MAX_DPCD_BUFFER_SIZE];
 	u8 i, j;
-	u8 g_edid_break = 0;
+	int g_edid_break = 0;
 	int ret;
 	struct device *dev = &ctx->client->dev;
 
@@ -826,7 +827,7 @@
 				g_edid_break = edid_read(ctx, offset,
 							 pblock_buf);
 
-				if (g_edid_break)
+				if (g_edid_break < 0)
 					break;
 
 				memcpy(&pedid_blocks_buf[offset],
@@ -887,7 +888,11 @@
 	}
 
 	/* Reset aux channel */
-	sp_tx_rst_aux(ctx);
+	ret = sp_tx_rst_aux(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to reset aux channel!\n");
+		return ret;
+	}
 
 	return (blocks_num + 1);
 }
@@ -1699,6 +1704,8 @@
 	mutex_lock(&ctx->lock);
 
 	anx7625_stop_dp_work(ctx);
+	if (!ctx->pdata.panel_bridge)
+		anx7625_remove_edid(ctx);
 	anx7625_power_standby(ctx);
 
 	mutex_unlock(&ctx->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/cadence/cdns-mhdp8546-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/cadence/cdns-mhdp8546-core.c
@@ -2040,6 +2040,9 @@
 	mhdp_state = to_cdns_mhdp_bridge_state(new_state);
 
 	mhdp_state->current_mode = drm_mode_duplicate(bridge->dev, mode);
+	if (!mhdp_state->current_mode)
+		return;
+
 	drm_mode_set_name(mhdp_state->current_mode);
 
 	dev_dbg(mhdp->dev, "%s: Enabling mode %s\n", __func__, mode->name);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/cadence/cdns-mhdp8546-hdcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/cadence/cdns-mhdp8546-hdcp.c
@@ -403,7 +403,8 @@
 
 static int _cdns_mhdp_hdcp_enable(struct cdns_mhdp_device *mhdp, u8 content_type)
 {
-	int ret, tries = 3;
+	int ret = -EINVAL;
+	int tries = 3;
 	u32 i;
 
 	for (i = 0; i < tries; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/cdns-dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/cdns-dsi.c
@@ -1286,6 +1286,7 @@
 	{ .compatible = "cdns,dsi" },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, cdns_dsi_of_match);
 
 static struct platform_driver cdns_dsi_platform_driver = {
 	.probe  = cdns_dsi_drm_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/chipone-icn6211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/chipone-icn6211.c
@@ -14,8 +14,19 @@
 #include <linux/of_device.h>
 #include <linux/regulator/consumer.h>
 
-#include <video/mipi_display.h>
-
+#define VENDOR_ID		0x00
+#define DEVICE_ID_H		0x01
+#define DEVICE_ID_L		0x02
+#define VERSION_ID		0x03
+#define FIRMWARE_VERSION	0x08
+#define CONFIG_FINISH		0x09
+#define PD_CTRL(n)		(0x0a + ((n) & 0x3)) /* 0..3 */
+#define RST_CTRL(n)		(0x0e + ((n) & 0x1)) /* 0..1 */
+#define SYS_CTRL(n)		(0x10 + ((n) & 0x7)) /* 0..4 */
+#define RGB_DRV(n)		(0x18 + ((n) & 0x3)) /* 0..3 */
+#define RGB_DLY(n)		(0x1c + ((n) & 0x1)) /* 0..1 */
+#define RGB_TEST_CTRL		0x1e
+#define ATE_PLL_EN		0x1f
 #define HACTIVE_LI		0x20
 #define VACTIVE_LI		0x21
 #define VACTIVE_HACTIVE_HI	0x22
@@ -23,9 +34,101 @@
 #define HSYNC_LI		0x24
 #define HBP_LI			0x25
 #define HFP_HSW_HBP_HI		0x26
+#define HFP_HSW_HBP_HI_HFP(n)		(((n) & 0x300) >> 4)
+#define HFP_HSW_HBP_HI_HS(n)		(((n) & 0x300) >> 6)
+#define HFP_HSW_HBP_HI_HBP(n)		(((n) & 0x300) >> 8)
 #define VFP			0x27
 #define VSYNC			0x28
 #define VBP			0x29
+#define BIST_POL		0x2a
+#define BIST_POL_BIST_MODE(n)		(((n) & 0xf) << 4)
+#define BIST_POL_BIST_GEN		BIT(3)
+#define BIST_POL_HSYNC_POL		BIT(2)
+#define BIST_POL_VSYNC_POL		BIT(1)
+#define BIST_POL_DE_POL			BIT(0)
+#define BIST_RED		0x2b
+#define BIST_GREEN		0x2c
+#define BIST_BLUE		0x2d
+#define BIST_CHESS_X		0x2e
+#define BIST_CHESS_Y		0x2f
+#define BIST_CHESS_XY_H		0x30
+#define BIST_FRAME_TIME_L	0x31
+#define BIST_FRAME_TIME_H	0x32
+#define FIFO_MAX_ADDR_LOW	0x33
+#define SYNC_EVENT_DLY		0x34
+#define HSW_MIN			0x35
+#define HFP_MIN			0x36
+#define LOGIC_RST_NUM		0x37
+#define OSC_CTRL(n)		(0x48 + ((n) & 0x7)) /* 0..5 */
+#define BG_CTRL			0x4e
+#define LDO_PLL			0x4f
+#define PLL_CTRL(n)		(0x50 + ((n) & 0xf)) /* 0..15 */
+#define PLL_CTRL_6_EXTERNAL		0x90
+#define PLL_CTRL_6_MIPI_CLK		0x92
+#define PLL_CTRL_6_INTERNAL		0x93
+#define PLL_REM(n)		(0x60 + ((n) & 0x3)) /* 0..2 */
+#define PLL_DIV(n)		(0x63 + ((n) & 0x3)) /* 0..2 */
+#define PLL_FRAC(n)		(0x66 + ((n) & 0x3)) /* 0..2 */
+#define PLL_INT(n)		(0x69 + ((n) & 0x1)) /* 0..1 */
+#define PLL_REF_DIV		0x6b
+#define PLL_REF_DIV_P(n)		((n) & 0xf)
+#define PLL_REF_DIV_Pe			BIT(4)
+#define PLL_REF_DIV_S(n)		(((n) & 0x7) << 5)
+#define PLL_SSC_P(n)		(0x6c + ((n) & 0x3)) /* 0..2 */
+#define PLL_SSC_STEP(n)		(0x6f + ((n) & 0x3)) /* 0..2 */
+#define PLL_SSC_OFFSET(n)	(0x72 + ((n) & 0x3)) /* 0..3 */
+#define GPIO_OEN		0x79
+#define MIPI_CFG_PW		0x7a
+#define MIPI_CFG_PW_CONFIG_DSI		0xc1
+#define MIPI_CFG_PW_CONFIG_I2C		0x3e
+#define GPIO_SEL(n)		(0x7b + ((n) & 0x1)) /* 0..1 */
+#define IRQ_SEL			0x7d
+#define DBG_SEL			0x7e
+#define DBG_SIGNAL		0x7f
+#define MIPI_ERR_VECTOR_L	0x80
+#define MIPI_ERR_VECTOR_H	0x81
+#define MIPI_ERR_VECTOR_EN_L	0x82
+#define MIPI_ERR_VECTOR_EN_H	0x83
+#define MIPI_MAX_SIZE_L		0x84
+#define MIPI_MAX_SIZE_H		0x85
+#define DSI_CTRL		0x86
+#define DSI_CTRL_UNKNOWN		0x28
+#define DSI_CTRL_DSI_LANES(n)		((n) & 0x3)
+#define MIPI_PN_SWAP		0x87
+#define MIPI_PN_SWAP_CLK		BIT(4)
+#define MIPI_PN_SWAP_D(n)		BIT((n) & 0x3)
+#define MIPI_SOT_SYNC_BIT_(n)	(0x88 + ((n) & 0x1)) /* 0..1 */
+#define MIPI_ULPS_CTRL		0x8a
+#define MIPI_CLK_CHK_VAR	0x8e
+#define MIPI_CLK_CHK_INI	0x8f
+#define MIPI_T_TERM_EN		0x90
+#define MIPI_T_HS_SETTLE	0x91
+#define MIPI_T_TA_SURE_PRE	0x92
+#define MIPI_T_LPX_SET		0x94
+#define MIPI_T_CLK_MISS		0x95
+#define MIPI_INIT_TIME_L	0x96
+#define MIPI_INIT_TIME_H	0x97
+#define MIPI_T_CLK_TERM_EN	0x99
+#define MIPI_T_CLK_SETTLE	0x9a
+#define MIPI_TO_HS_RX_L		0x9e
+#define MIPI_TO_HS_RX_H		0x9f
+#define MIPI_PHY_(n)		(0xa0 + ((n) & 0x7)) /* 0..5 */
+#define MIPI_PD_RX		0xb0
+#define MIPI_PD_TERM		0xb1
+#define MIPI_PD_HSRX		0xb2
+#define MIPI_PD_LPTX		0xb3
+#define MIPI_PD_LPRX		0xb4
+#define MIPI_PD_CK_LANE		0xb5
+#define MIPI_FORCE_0		0xb6
+#define MIPI_RST_CTRL		0xb7
+#define MIPI_RST_NUM		0xb8
+#define MIPI_DBG_SET_(n)	(0xc0 + ((n) & 0xf)) /* 0..9 */
+#define MIPI_DBG_SEL		0xe0
+#define MIPI_DBG_DATA		0xe1
+#define MIPI_ATE_TEST_SEL	0xe2
+#define MIPI_ATE_STATUS_(n)	(0xe3 + ((n) & 0x1)) /* 0..1 */
+#define MIPI_ATE_STATUS_1	0xe4
+#define ICN6211_MAX_REGISTER	MIPI_ATE_STATUS(1)
 
 struct chipone {
 	struct device *dev;
@@ -65,14 +168,15 @@
 {
 	struct chipone *icn = bridge_to_chipone(bridge);
 	struct drm_display_mode *mode = bridge_to_mode(bridge);
+	u16 hfp, hbp, hsync;
 
-	ICN6211_DSI(icn, 0x7a, 0xc1);
+	ICN6211_DSI(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI);
 
 	ICN6211_DSI(icn, HACTIVE_LI, mode->hdisplay & 0xff);
 
 	ICN6211_DSI(icn, VACTIVE_LI, mode->vdisplay & 0xff);
 
-	/**
+	/*
 	 * lsb nibble: 2nd nibble of hdisplay
 	 * msb nibble: 2nd nibble of vdisplay
 	 */
@@ -80,13 +184,18 @@
 		    ((mode->hdisplay >> 8) & 0xf) |
 		    (((mode->vdisplay >> 8) & 0xf) << 4));
 
-	ICN6211_DSI(icn, HFP_LI, mode->hsync_start - mode->hdisplay);
-
-	ICN6211_DSI(icn, HSYNC_LI, mode->hsync_end - mode->hsync_start);
-
-	ICN6211_DSI(icn, HBP_LI, mode->htotal - mode->hsync_end);
-
-	ICN6211_DSI(icn, HFP_HSW_HBP_HI, 0x00);
+	hfp = mode->hsync_start - mode->hdisplay;
+	hsync = mode->hsync_end - mode->hsync_start;
+	hbp = mode->htotal - mode->hsync_end;
+
+	ICN6211_DSI(icn, HFP_LI, hfp & 0xff);
+	ICN6211_DSI(icn, HSYNC_LI, hsync & 0xff);
+	ICN6211_DSI(icn, HBP_LI, hbp & 0xff);
+	/* Top two bits of Horizontal Front porch/Sync/Back porch */
+	ICN6211_DSI(icn, HFP_HSW_HBP_HI,
+		    HFP_HSW_HBP_HI_HFP(hfp) |
+		    HFP_HSW_HBP_HI_HS(hsync) |
+		    HFP_HSW_HBP_HI_HBP(hbp));
 
 	ICN6211_DSI(icn, VFP, mode->vsync_start - mode->vdisplay);
 
@@ -95,21 +204,21 @@
 	ICN6211_DSI(icn, VBP, mode->vtotal - mode->vsync_end);
 
 	/* dsi specific sequence */
-	ICN6211_DSI(icn, MIPI_DCS_SET_TEAR_OFF, 0x80);
-	ICN6211_DSI(icn, MIPI_DCS_SET_ADDRESS_MODE, 0x28);
-	ICN6211_DSI(icn, 0xb5, 0xa0);
-	ICN6211_DSI(icn, 0x5c, 0xff);
-	ICN6211_DSI(icn, MIPI_DCS_SET_COLUMN_ADDRESS, 0x01);
-	ICN6211_DSI(icn, MIPI_DCS_GET_POWER_SAVE, 0x92);
-	ICN6211_DSI(icn, 0x6b, 0x71);
-	ICN6211_DSI(icn, 0x69, 0x2b);
-	ICN6211_DSI(icn, MIPI_DCS_ENTER_SLEEP_MODE, 0x40);
-	ICN6211_DSI(icn, MIPI_DCS_EXIT_SLEEP_MODE, 0x98);
+	ICN6211_DSI(icn, SYNC_EVENT_DLY, 0x80);
+	ICN6211_DSI(icn, HFP_MIN, hfp & 0xff);
+	ICN6211_DSI(icn, MIPI_PD_CK_LANE, 0xa0);
+	ICN6211_DSI(icn, PLL_CTRL(12), 0xff);
+	ICN6211_DSI(icn, BIST_POL, BIST_POL_DE_POL);
+	ICN6211_DSI(icn, PLL_CTRL(6), PLL_CTRL_6_MIPI_CLK);
+	ICN6211_DSI(icn, PLL_REF_DIV, 0x71);
+	ICN6211_DSI(icn, PLL_INT(0), 0x2b);
+	ICN6211_DSI(icn, SYS_CTRL(0), 0x40);
+	ICN6211_DSI(icn, SYS_CTRL(1), 0x98);
 
 	/* icn6211 specific sequence */
-	ICN6211_DSI(icn, 0xb6, 0x20);
-	ICN6211_DSI(icn, 0x51, 0x20);
-	ICN6211_DSI(icn, 0x09, 0x10);
+	ICN6211_DSI(icn, MIPI_FORCE_0, 0x20);
+	ICN6211_DSI(icn, PLL_CTRL(1), 0x20);
+	ICN6211_DSI(icn, CONFIG_FINISH, 0x10);
 
 	usleep_range(10000, 11000);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/display-connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/display-connector.c
@@ -13,6 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/consumer.h>
 
+#include <drm/drm_atomic_helper.h>
 #include <drm/drm_bridge.h>
 #include <drm/drm_edid.h>
 
@@ -87,10 +88,95 @@
 	return drm_get_edid(connector, conn->bridge.ddc);
 }
 
+/*
+ * Since this bridge is tied to the connector, it acts like a passthrough,
+ * so concerning the output bus formats, either pass the bus formats from the
+ * previous bridge or return fallback data like done in the bridge function:
+ * drm_atomic_bridge_chain_select_bus_fmts().
+ * This supports negotiation if the bridge chain has all bits in place.
+ */
+static u32 *display_connector_get_output_bus_fmts(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state,
+					unsigned int *num_output_fmts)
+{
+	struct drm_bridge *prev_bridge = drm_bridge_get_prev_bridge(bridge);
+	struct drm_bridge_state *prev_bridge_state;
+
+	if (!prev_bridge || !prev_bridge->funcs->atomic_get_output_bus_fmts) {
+		struct drm_connector *conn = conn_state->connector;
+		u32 *out_bus_fmts;
+
+		*num_output_fmts = 1;
+		out_bus_fmts = kmalloc(sizeof(*out_bus_fmts), GFP_KERNEL);
+		if (!out_bus_fmts)
+			return NULL;
+
+		if (conn->display_info.num_bus_formats &&
+		    conn->display_info.bus_formats)
+			out_bus_fmts[0] = conn->display_info.bus_formats[0];
+		else
+			out_bus_fmts[0] = MEDIA_BUS_FMT_FIXED;
+
+		return out_bus_fmts;
+	}
+
+	prev_bridge_state = drm_atomic_get_new_bridge_state(crtc_state->state,
+							    prev_bridge);
+
+	return prev_bridge->funcs->atomic_get_output_bus_fmts(prev_bridge, prev_bridge_state,
+							      crtc_state, conn_state,
+							      num_output_fmts);
+}
+
+/*
+ * Since this bridge is tied to the connector, it acts like a passthrough,
+ * so concerning the input bus formats, either pass the bus formats from the
+ * previous bridge or MEDIA_BUS_FMT_FIXED (like select_bus_fmt_recursive())
+ * when atomic_get_input_bus_fmts is not supported.
+ * This supports negotiation if the bridge chain has all bits in place.
+ */
+static u32 *display_connector_get_input_bus_fmts(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state,
+					u32 output_fmt,
+					unsigned int *num_input_fmts)
+{
+	struct drm_bridge *prev_bridge = drm_bridge_get_prev_bridge(bridge);
+	struct drm_bridge_state *prev_bridge_state;
+
+	if (!prev_bridge || !prev_bridge->funcs->atomic_get_input_bus_fmts) {
+		u32 *in_bus_fmts;
+
+		*num_input_fmts = 1;
+		in_bus_fmts = kmalloc(sizeof(*in_bus_fmts), GFP_KERNEL);
+		if (!in_bus_fmts)
+			return NULL;
+
+		in_bus_fmts[0] = MEDIA_BUS_FMT_FIXED;
+
+		return in_bus_fmts;
+	}
+
+	prev_bridge_state = drm_atomic_get_new_bridge_state(crtc_state->state,
+							    prev_bridge);
+
+	return prev_bridge->funcs->atomic_get_input_bus_fmts(prev_bridge, prev_bridge_state,
+							     crtc_state, conn_state, output_fmt,
+							     num_input_fmts);
+}
+
 static const struct drm_bridge_funcs display_connector_bridge_funcs = {
 	.attach = display_connector_attach,
 	.detect = display_connector_detect,
 	.get_edid = display_connector_get_edid,
+	.atomic_get_output_bus_fmts = display_connector_get_output_bus_fmts,
+	.atomic_get_input_bus_fmts = display_connector_get_input_bus_fmts,
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
 };
 
 static irqreturn_t display_connector_hpd_irq(int irq, void *arg)
@@ -107,7 +193,7 @@
 {
 	struct display_connector *conn;
 	unsigned int type;
-	const char *label;
+	const char *label = NULL;
 	int ret;
 
 	conn = devm_kzalloc(&pdev->dev, sizeof(*conn), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/ite-it66121.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/ite-it66121.c
@@ -227,7 +227,7 @@
 		.selector_mask = 0x1,
 		.selector_shift = 0,
 		.window_start = 0x00,
-		.window_len = 0x130,
+		.window_len = 0x100,
 	},
 };
 
@@ -889,7 +889,7 @@
 static int it66121_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
-	u32 vendor_ids[2], device_ids[2], revision_id;
+	u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
 	struct device_node *ep;
 	int ret;
 	struct it66121_ctx *ctx;
@@ -918,11 +918,26 @@
 		return -EINVAL;
 
 	ep = of_graph_get_remote_node(dev->of_node, 1, -1);
-	if (!ep)
-		return -EPROBE_DEFER;
+	if (!ep) {
+		dev_err(ctx->dev, "The endpoint is unconnected\n");
+		return -EINVAL;
+	}
+
+	if (!of_device_is_available(ep)) {
+		of_node_put(ep);
+		dev_err(ctx->dev, "The remote device is disabled\n");
+		return -ENODEV;
+	}
 
 	ctx->next_bridge = of_drm_find_bridge(ep);
 	of_node_put(ep);
+	if (!ctx->next_bridge) {
+		dev_dbg(ctx->dev, "Next bridge not found, deferring probe\n");
+		return -EPROBE_DEFER;
+	}
+
+	if (!ctx->next_bridge)
+		return -EPROBE_DEFER;
 
 	i2c_set_clientdata(client, ctx);
 	mutex_init(&ctx->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/lontium-lt8912b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/lontium-lt8912b.c
@@ -43,7 +43,6 @@
 
 	u8 data_lanes;
 	bool is_power_on;
-	bool is_attached;
 };
 
 static int lt8912_write_init_config(struct lt8912 *lt)
@@ -186,7 +185,7 @@
 		{0x03, 0xff},
 	};
 
-	return regmap_multi_reg_write(lt->regmap[I2C_CEC_DSI], seq, ARRAY_SIZE(seq));
+	return regmap_multi_reg_write(lt->regmap[I2C_MAIN], seq, ARRAY_SIZE(seq));
 };
 
 static inline struct lt8912 *bridge_to_lt8912(struct drm_bridge *b)
@@ -266,7 +265,7 @@
 	u32 hactive, h_total, hpw, hfp, hbp;
 	u32 vactive, v_total, vpw, vfp, vbp;
 	u8 settle = 0x08;
-	int ret;
+	int ret, hsync_activehigh, vsync_activehigh;
 
 	if (!lt)
 		return -EINVAL;
@@ -276,12 +275,14 @@
 	hpw = lt->mode.hsync_len;
 	hbp = lt->mode.hback_porch;
 	h_total = hactive + hfp + hpw + hbp;
+	hsync_activehigh = lt->mode.flags & DISPLAY_FLAGS_HSYNC_HIGH;
 
 	vactive = lt->mode.vactive;
 	vfp = lt->mode.vfront_porch;
 	vpw = lt->mode.vsync_len;
 	vbp = lt->mode.vback_porch;
 	v_total = vactive + vfp + vpw + vbp;
+	vsync_activehigh = lt->mode.flags & DISPLAY_FLAGS_VSYNC_HIGH;
 
 	if (vactive <= 600)
 		settle = 0x04;
@@ -315,6 +316,13 @@
 	ret |= regmap_write(lt->regmap[I2C_CEC_DSI], 0x3e, hfp & 0xff);
 	ret |= regmap_write(lt->regmap[I2C_CEC_DSI], 0x3f, hfp >> 8);
 
+	ret |= regmap_update_bits(lt->regmap[I2C_MAIN], 0xab, BIT(0),
+				  vsync_activehigh ? BIT(0) : 0);
+	ret |= regmap_update_bits(lt->regmap[I2C_MAIN], 0xab, BIT(1),
+				  hsync_activehigh ? BIT(1) : 0);
+	ret |= regmap_update_bits(lt->regmap[I2C_MAIN], 0xb2, BIT(0),
+				  lt->connector.display_info.is_hdmi ? BIT(0) : 0);
+
 	return ret;
 }
 
@@ -393,22 +401,6 @@
 	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
 };
 
-static enum drm_mode_status
-lt8912_connector_mode_valid(struct drm_connector *connector,
-			    struct drm_display_mode *mode)
-{
-	if (mode->clock > 150000)
-		return MODE_CLOCK_HIGH;
-
-	if (mode->hdisplay > 1920)
-		return MODE_BAD_HVALUE;
-
-	if (mode->vdisplay > 1080)
-		return MODE_BAD_VVALUE;
-
-	return MODE_OK;
-}
-
 static int lt8912_connector_get_modes(struct drm_connector *connector)
 {
 	struct edid *edid;
@@ -436,7 +428,6 @@
 
 static const struct drm_connector_helper_funcs lt8912_connector_helper_funcs = {
 	.get_modes = lt8912_connector_get_modes,
-	.mode_valid = lt8912_connector_mode_valid,
 };
 
 static void lt8912_bridge_mode_set(struct drm_bridge *bridge,
@@ -467,16 +458,14 @@
 						 };
 
 	host = of_find_mipi_dsi_host_by_node(lt->host_node);
-	if (!host) {
-		dev_err(dev, "failed to find dsi host\n");
-		return -EPROBE_DEFER;
-	}
+	if (!host)
+		return dev_err_probe(dev, -EPROBE_DEFER, "failed to find dsi host\n");
 
-	dsi = mipi_dsi_device_register_full(host, &info);
+	dsi = devm_mipi_dsi_device_register_full(dev, host, &info);
 	if (IS_ERR(dsi)) {
 		ret = PTR_ERR(dsi);
 		dev_err(dev, "failed to create dsi device (%d)\n", ret);
-		goto err_dsi_device;
+		return ret;
 	}
 
 	lt->dsi = dsi;
@@ -485,28 +474,24 @@
 	dsi->format = MIPI_DSI_FMT_RGB888;
 
 	dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
-			  MIPI_DSI_MODE_VIDEO_BURST |
 			  MIPI_DSI_MODE_LPM |
 			  MIPI_DSI_MODE_NO_EOT_PACKET;
 
-	ret = mipi_dsi_attach(dsi);
+	ret = devm_mipi_dsi_attach(dev, dsi);
 	if (ret < 0) {
 		dev_err(dev, "failed to attach dsi to host\n");
-		goto err_dsi_attach;
+		return ret;
 	}
 
 	return 0;
-
-err_dsi_attach:
-	mipi_dsi_device_unregister(dsi);
-err_dsi_device:
-	return ret;
 }
 
-static void lt8912_detach_dsi(struct lt8912 *lt)
+static void lt8912_bridge_hpd_cb(void *data, enum drm_connector_status status)
 {
-	mipi_dsi_detach(lt->dsi);
-	mipi_dsi_device_unregister(lt->dsi);
+	struct lt8912 *lt = data;
+
+	if (lt->bridge.dev)
+		drm_helper_hpd_irq_event(lt->bridge.dev);
 }
 
 static int lt8912_bridge_connector_init(struct drm_bridge *bridge)
@@ -515,8 +500,13 @@
 	struct lt8912 *lt = bridge_to_lt8912(bridge);
 	struct drm_connector *connector = &lt->connector;
 
-	connector->polled = DRM_CONNECTOR_POLL_CONNECT |
-			    DRM_CONNECTOR_POLL_DISCONNECT;
+	if (lt->hdmi_port->ops & DRM_BRIDGE_OP_HPD) {
+		drm_bridge_hpd_enable(lt->hdmi_port, lt8912_bridge_hpd_cb, lt);
+		connector->polled = DRM_CONNECTOR_POLL_HPD;
+	} else {
+		connector->polled = DRM_CONNECTOR_POLL_CONNECT |
+				    DRM_CONNECTOR_POLL_DISCONNECT;
+	}
 
 	ret = drm_connector_init(bridge->dev, connector,
 				 &lt8912_connector_funcs,
@@ -539,6 +529,13 @@
 	struct lt8912 *lt = bridge_to_lt8912(bridge);
 	int ret;
 
+	ret = drm_bridge_attach(bridge->encoder, lt->hdmi_port, bridge,
+				DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+	if (ret < 0) {
+		dev_err(lt->dev, "Failed to attach next bridge (%d)\n", ret);
+		return ret;
+	}
+
 	if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
 		ret = lt8912_bridge_connector_init(bridge);
 		if (ret) {
@@ -559,8 +556,6 @@
 	if (ret)
 		goto error;
 
-	lt->is_attached = true;
-
 	return 0;
 
 error:
@@ -572,12 +567,27 @@
 {
 	struct lt8912 *lt = bridge_to_lt8912(bridge);
 
-	if (lt->is_attached) {
-		lt8912_detach_dsi(lt);
-		lt8912_hard_power_off(lt);
-		drm_connector_unregister(&lt->connector);
-		drm_connector_cleanup(&lt->connector);
-	}
+	lt8912_hard_power_off(lt);
+
+	if (lt->connector.dev && lt->hdmi_port->ops & DRM_BRIDGE_OP_HPD)
+		drm_bridge_hpd_disable(lt->hdmi_port);
+}
+
+static enum drm_mode_status
+lt8912_bridge_mode_valid(struct drm_bridge *bridge,
+			 const struct drm_display_info *info,
+			 const struct drm_display_mode *mode)
+{
+	if (mode->clock > 150000)
+		return MODE_CLOCK_HIGH;
+
+	if (mode->hdisplay > 1920)
+		return MODE_BAD_HVALUE;
+
+	if (mode->vdisplay > 1080)
+		return MODE_BAD_VVALUE;
+
+	return MODE_OK;
 }
 
 static enum drm_connector_status
@@ -610,6 +620,7 @@
 static const struct drm_bridge_funcs lt8912_bridge_funcs = {
 	.attach = lt8912_bridge_attach,
 	.detach = lt8912_bridge_detach,
+	.mode_valid = lt8912_bridge_mode_valid,
 	.mode_set = lt8912_bridge_mode_set,
 	.enable = lt8912_bridge_enable,
 	.detect = lt8912_bridge_detect,
@@ -661,8 +672,8 @@
 
 	lt->hdmi_port = of_drm_find_bridge(port_node);
 	if (!lt->hdmi_port) {
-		dev_err(lt->dev, "%s: Failed to get hdmi port\n", __func__);
-		ret = -ENODEV;
+		ret = -EPROBE_DEFER;
+		dev_err_probe(lt->dev, ret, "%s: Failed to get hdmi port\n", __func__);
 		goto err_free_host_node;
 	}
 
@@ -730,7 +741,6 @@
 {
 	struct lt8912 *lt = i2c_get_clientdata(client);
 
-	lt8912_bridge_detach(&lt->bridge);
 	drm_bridge_remove(&lt->bridge);
 	lt8912_free_i2c(lt);
 	lt8912_put_dt(lt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/lontium-lt9611.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/lontium-lt9611.c
@@ -185,12 +185,14 @@
 
 	regmap_write(lt9611->regmap, 0x8319, (u8)(hfront_porch % 256));
 
-	regmap_write(lt9611->regmap, 0x831a, (u8)(hsync_porch / 256));
+	regmap_write(lt9611->regmap, 0x831a, (u8)(hsync_porch / 256) |
+						((hfront_porch / 256) << 4));
 	regmap_write(lt9611->regmap, 0x831b, (u8)(hsync_porch % 256));
 }
 
-static void lt9611_pcr_setup(struct lt9611 *lt9611, const struct drm_display_mode *mode)
+static void lt9611_pcr_setup(struct lt9611 *lt9611, const struct drm_display_mode *mode, unsigned int postdiv)
 {
+	unsigned int pcr_m = mode->clock * 5 * postdiv / 27000;
 	const struct reg_sequence reg_cfg[] = {
 		{ 0x830b, 0x01 },
 		{ 0x830c, 0x10 },
@@ -205,7 +207,6 @@
 
 		/* stage 2 */
 		{ 0x834a, 0x40 },
-		{ 0x831d, 0x10 },
 
 		/* MK limit */
 		{ 0x832d, 0x38 },
@@ -220,30 +221,28 @@
 		{ 0x8325, 0x00 },
 		{ 0x832a, 0x01 },
 		{ 0x834a, 0x10 },
-		{ 0x831d, 0x10 },
-		{ 0x8326, 0x37 },
 	};
+	u8 pol = 0x10;
 
-	regmap_multi_reg_write(lt9611->regmap, reg_cfg, ARRAY_SIZE(reg_cfg));
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+		pol |= 0x2;
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+		pol |= 0x1;
+	regmap_write(lt9611->regmap, 0x831d, pol);
 
-	switch (mode->hdisplay) {
-	case 640:
-		regmap_write(lt9611->regmap, 0x8326, 0x14);
-		break;
-	case 1920:
-		regmap_write(lt9611->regmap, 0x8326, 0x37);
-		break;
-	case 3840:
+	if (mode->hdisplay == 3840)
 		regmap_multi_reg_write(lt9611->regmap, reg_cfg2, ARRAY_SIZE(reg_cfg2));
-		break;
-	}
+	else
+		regmap_multi_reg_write(lt9611->regmap, reg_cfg, ARRAY_SIZE(reg_cfg));
+
+	regmap_write(lt9611->regmap, 0x8326, pcr_m);
 
 	/* pcr rst */
 	regmap_write(lt9611->regmap, 0x8011, 0x5a);
 	regmap_write(lt9611->regmap, 0x8011, 0xfa);
 }
 
-static int lt9611_pll_setup(struct lt9611 *lt9611, const struct drm_display_mode *mode)
+static int lt9611_pll_setup(struct lt9611 *lt9611, const struct drm_display_mode *mode, unsigned int *postdiv)
 {
 	unsigned int pclk = mode->clock;
 	const struct reg_sequence reg_cfg[] = {
@@ -257,16 +256,21 @@
 		{ 0x8126, 0x55 },
 		{ 0x8127, 0x66 },
 		{ 0x8128, 0x88 },
+		{ 0x812a, 0x20 },
 	};
 
 	regmap_multi_reg_write(lt9611->regmap, reg_cfg, ARRAY_SIZE(reg_cfg));
 
-	if (pclk > 150000)
+	if (pclk > 150000) {
 		regmap_write(lt9611->regmap, 0x812d, 0x88);
-	else if (pclk > 70000)
+		*postdiv = 1;
+	} else if (pclk > 70000) {
 		regmap_write(lt9611->regmap, 0x812d, 0x99);
-	else
+		*postdiv = 2;
+	} else {
 		regmap_write(lt9611->regmap, 0x812d, 0xaa);
+		*postdiv = 4;
+	}
 
 	/*
 	 * first divide pclk by 2 first
@@ -446,12 +450,11 @@
 		{ 0x8023, 0x01 },
 		{ 0x8157, 0x03 }, /* set addr pin as output */
 		{ 0x8149, 0x0b },
-		{ 0x8151, 0x30 }, /* disable IRQ */
+
 		{ 0x8102, 0x48 }, /* MIPI Rx power down */
 		{ 0x8123, 0x80 },
 		{ 0x8130, 0x00 },
-		{ 0x8100, 0x01 }, /* bandgap power down */
-		{ 0x8101, 0x00 }, /* system clk power down */
+		{ 0x8011, 0x0a },
 	};
 
 	regmap_multi_reg_write(lt9611->regmap,
@@ -757,16 +760,14 @@
 static struct mipi_dsi_device *lt9611_attach_dsi(struct lt9611 *lt9611,
 						 struct device_node *dsi_node)
 {
-	const struct mipi_dsi_device_info info = { "lt9611", 0, NULL };
+	const struct mipi_dsi_device_info info = { "lt9611", 0, lt9611->dev->of_node};
 	struct mipi_dsi_device *dsi;
 	struct mipi_dsi_host *host;
 	int ret;
 
 	host = of_find_mipi_dsi_host_by_node(dsi_node);
-	if (!host) {
-		dev_err(lt9611->dev, "failed to find dsi host\n");
-		return ERR_PTR(-EPROBE_DEFER);
-	}
+	if (!host)
+		return ERR_PTR(dev_err_probe(lt9611->dev, -EPROBE_DEFER, "failed to find dsi host\n"));
 
 	dsi = mipi_dsi_device_register_full(host, &info);
 	if (IS_ERR(dsi)) {
@@ -816,13 +817,14 @@
 
 	drm_connector_helper_add(&lt9611->connector,
 				 &lt9611_bridge_connector_helper_funcs);
-	drm_connector_attach_encoder(&lt9611->connector, bridge->encoder);
 
 	if (!bridge->encoder) {
 		DRM_ERROR("Parent encoder object not found");
 		return -ENODEV;
 	}
 
+	drm_connector_attach_encoder(&lt9611->connector, bridge->encoder);
+
 	return 0;
 }
 
@@ -880,12 +882,18 @@
 static void lt9611_bridge_pre_enable(struct drm_bridge *bridge)
 {
 	struct lt9611 *lt9611 = bridge_to_lt9611(bridge);
+	static const struct reg_sequence reg_cfg[] = {
+		{ 0x8102, 0x12 },
+		{ 0x8123, 0x40 },
+		{ 0x8130, 0xea },
+		{ 0x8011, 0xfa },
+	};
 
 	if (!lt9611->sleep)
 		return;
 
-	lt9611_reset(lt9611);
-	regmap_write(lt9611->regmap, 0x80ee, 0x01);
+	regmap_multi_reg_write(lt9611->regmap,
+			       reg_cfg, ARRAY_SIZE(reg_cfg));
 
 	lt9611->sleep = false;
 }
@@ -903,14 +911,15 @@
 {
 	struct lt9611 *lt9611 = bridge_to_lt9611(bridge);
 	struct hdmi_avi_infoframe avi_frame;
+	unsigned int postdiv;
 	int ret;
 
 	lt9611_bridge_pre_enable(bridge);
 
 	lt9611_mipi_input_digital(lt9611, mode);
-	lt9611_pll_setup(lt9611, mode);
+	lt9611_pll_setup(lt9611, mode, &postdiv);
 	lt9611_mipi_video_setup(lt9611, mode);
-	lt9611_pcr_setup(lt9611, mode);
+	lt9611_pcr_setup(lt9611, mode, postdiv);
 
 	ret = drm_hdmi_avi_infoframe_from_display_mode(&avi_frame,
 						       &lt9611->connector,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/lontium-lt9611uxc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/lontium-lt9611uxc.c
@@ -167,9 +167,10 @@
 	struct lt9611uxc *lt9611uxc = container_of(work, struct lt9611uxc, work);
 	bool connected;
 
-	if (lt9611uxc->connector.dev)
-		drm_kms_helper_hotplug_event(lt9611uxc->connector.dev);
-	else {
+	if (lt9611uxc->connector.dev) {
+		if (lt9611uxc->connector.dev->mode_config.funcs)
+			drm_kms_helper_hotplug_event(lt9611uxc->connector.dev);
+	} else {
 
 		mutex_lock(&lt9611uxc->ocm_lock);
 		connected = lt9611uxc->hdmi_connected;
@@ -339,6 +340,8 @@
 		return -ENODEV;
 	}
 
+	lt9611uxc->connector.polled = DRM_CONNECTOR_POLL_HPD;
+
 	drm_connector_helper_add(&lt9611uxc->connector,
 				 &lt9611uxc_bridge_connector_helper_funcs);
 	ret = drm_connector_init(bridge->dev, &lt9611uxc->connector,
@@ -994,7 +997,7 @@
 	struct lt9611uxc *lt9611uxc = i2c_get_clientdata(client);
 
 	disable_irq(client->irq);
-	flush_scheduled_work();
+	cancel_work_sync(&lt9611uxc->work);
 	lt9611uxc_audio_exit(lt9611uxc);
 	drm_bridge_remove(&lt9611uxc->bridge);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/megachips-stdpxxxx-ge-b850v3-fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/megachips-stdpxxxx-ge-b850v3-fw.c
@@ -296,7 +296,9 @@
 	 * This check is to avoid both the drivers
 	 * removing the bridge in their remove() function
 	 */
-	if (!ge_b850v3_lvds_ptr)
+	if (!ge_b850v3_lvds_ptr ||
+	    !ge_b850v3_lvds_ptr->stdp2690_i2c ||
+		!ge_b850v3_lvds_ptr->stdp4028_i2c)
 		goto out;
 
 	drm_bridge_remove(&ge_b850v3_lvds_ptr->bridge);
@@ -306,19 +308,10 @@
 	mutex_unlock(&ge_b850v3_lvds_dev_mutex);
 }
 
-static int stdp4028_ge_b850v3_fw_probe(struct i2c_client *stdp4028_i2c,
-				       const struct i2c_device_id *id)
+static int ge_b850v3_register(void)
 {
+	struct i2c_client *stdp4028_i2c = ge_b850v3_lvds_ptr->stdp4028_i2c;
 	struct device *dev = &stdp4028_i2c->dev;
-	int ret;
-
-	ret = ge_b850v3_lvds_init(dev);
-
-	if (ret)
-		return ret;
-
-	ge_b850v3_lvds_ptr->stdp4028_i2c = stdp4028_i2c;
-	i2c_set_clientdata(stdp4028_i2c, ge_b850v3_lvds_ptr);
 
 	/* drm bridge initialization */
 	ge_b850v3_lvds_ptr->bridge.funcs = &ge_b850v3_lvds_funcs;
@@ -343,6 +336,27 @@
 			"ge-b850v3-lvds-dp", ge_b850v3_lvds_ptr);
 }
 
+static int stdp4028_ge_b850v3_fw_probe(struct i2c_client *stdp4028_i2c,
+				       const struct i2c_device_id *id)
+{
+	struct device *dev = &stdp4028_i2c->dev;
+	int ret;
+
+	ret = ge_b850v3_lvds_init(dev);
+
+	if (ret)
+		return ret;
+
+	ge_b850v3_lvds_ptr->stdp4028_i2c = stdp4028_i2c;
+	i2c_set_clientdata(stdp4028_i2c, ge_b850v3_lvds_ptr);
+
+	/* Only register after both bridges are probed */
+	if (!ge_b850v3_lvds_ptr->stdp2690_i2c)
+		return 0;
+
+	return ge_b850v3_register();
+}
+
 static int stdp4028_ge_b850v3_fw_remove(struct i2c_client *stdp4028_i2c)
 {
 	ge_b850v3_lvds_remove();
@@ -386,7 +400,11 @@
 	ge_b850v3_lvds_ptr->stdp2690_i2c = stdp2690_i2c;
 	i2c_set_clientdata(stdp2690_i2c, ge_b850v3_lvds_ptr);
 
-	return 0;
+	/* Only register after both bridges are probed */
+	if (!ge_b850v3_lvds_ptr->stdp4028_i2c)
+		return 0;
+
+	return ge_b850v3_register();
 }
 
 static int stdp2690_ge_b850v3_fw_remove(struct i2c_client *stdp2690_i2c)
@@ -426,7 +444,11 @@
 	if (ret)
 		return ret;
 
-	return i2c_add_driver(&stdp2690_ge_b850v3_fw_driver);
+	ret = i2c_add_driver(&stdp2690_ge_b850v3_fw_driver);
+	if (ret)
+		i2c_del_driver(&stdp4028_ge_b850v3_fw_driver);
+
+	return ret;
 }
 module_init(stdpxxxx_ge_b850v3_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/nwl-dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/nwl-dsi.c
@@ -7,6 +7,7 @@
  */
 
 #include <linux/bitfield.h>
+#include <linux/bits.h>
 #include <linux/clk.h>
 #include <linux/irq.h>
 #include <linux/math64.h>
@@ -196,12 +197,9 @@
 /*
  * ui2bc - UI time periods to byte clock cycles
  */
-static u32 ui2bc(struct nwl_dsi *dsi, unsigned long long ui)
+static u32 ui2bc(unsigned int ui)
 {
-	u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
-
-	return DIV64_U64_ROUND_UP(ui * dsi->lanes,
-				  dsi->mode.clock * 1000 * bpp);
+	return DIV_ROUND_UP(ui, BITS_PER_BYTE);
 }
 
 /*
@@ -232,12 +230,12 @@
 	}
 
 	/* values in byte clock cycles */
-	cycles = ui2bc(dsi, cfg->clk_pre);
+	cycles = ui2bc(cfg->clk_pre);
 	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_pre: 0x%x\n", cycles);
 	nwl_dsi_write(dsi, NWL_DSI_CFG_T_PRE, cycles);
 	cycles = ps2bc(dsi, cfg->lpx + cfg->clk_prepare + cfg->clk_zero);
 	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap (pre): 0x%x\n", cycles);
-	cycles += ui2bc(dsi, cfg->clk_pre);
+	cycles += ui2bc(cfg->clk_pre);
 	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_post: 0x%x\n", cycles);
 	nwl_dsi_write(dsi, NWL_DSI_CFG_T_POST, cycles);
 	cycles = ps2bc(dsi, cfg->hs_exit);
@@ -863,18 +861,19 @@
 	memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
 	drm_mode_debug_printmodeline(adjusted_mode);
 
-	pm_runtime_get_sync(dev);
+	if (pm_runtime_resume_and_get(dev) < 0)
+		return;
 
 	if (clk_prepare_enable(dsi->lcdif_clk) < 0)
-		return;
+		goto runtime_put;
 	if (clk_prepare_enable(dsi->core_clk) < 0)
-		return;
+		goto runtime_put;
 
 	/* Step 1 from DSI reset-out instructions */
 	ret = reset_control_deassert(dsi->rst_pclk);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to deassert PCLK: %d\n", ret);
-		return;
+		goto runtime_put;
 	}
 
 	/* Step 2 from DSI reset-out instructions */
@@ -884,13 +883,18 @@
 	ret = reset_control_deassert(dsi->rst_esc);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to deassert ESC: %d\n", ret);
-		return;
+		goto runtime_put;
 	}
 	ret = reset_control_deassert(dsi->rst_byte);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to deassert BYTE: %d\n", ret);
-		return;
+		goto runtime_put;
 	}
+
+	return;
+
+runtime_put:
+	pm_runtime_put_sync(dev);
 }
 
 static void
@@ -939,6 +943,40 @@
 	drm_of_panel_bridge_remove(dsi->dev->of_node, 1, 0);
 }
 
+static u32 *nwl_bridge_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+						 struct drm_bridge_state *bridge_state,
+						 struct drm_crtc_state *crtc_state,
+						 struct drm_connector_state *conn_state,
+						 u32 output_fmt,
+						 unsigned int *num_input_fmts)
+{
+	u32 *input_fmts, input_fmt;
+
+	*num_input_fmts = 0;
+
+	switch (output_fmt) {
+	/* If MEDIA_BUS_FMT_FIXED is tested, return default bus format */
+	case MEDIA_BUS_FMT_FIXED:
+		input_fmt = MEDIA_BUS_FMT_RGB888_1X24;
+		break;
+	case MEDIA_BUS_FMT_RGB888_1X24:
+	case MEDIA_BUS_FMT_RGB666_1X18:
+	case MEDIA_BUS_FMT_RGB565_1X16:
+		input_fmt = output_fmt;
+		break;
+	default:
+		return NULL;
+	}
+
+	input_fmts = kcalloc(1, sizeof(*input_fmts), GFP_KERNEL);
+	if (!input_fmts)
+		return NULL;
+	input_fmts[0] = input_fmt;
+	*num_input_fmts = 1;
+
+	return input_fmts;
+}
+
 static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
 	.atomic_duplicate_state	= drm_atomic_helper_bridge_duplicate_state,
 	.atomic_destroy_state	= drm_atomic_helper_bridge_destroy_state,
@@ -946,6 +984,7 @@
 	.atomic_check		= nwl_dsi_bridge_atomic_check,
 	.atomic_enable		= nwl_dsi_bridge_atomic_enable,
 	.atomic_disable		= nwl_dsi_bridge_atomic_disable,
+	.atomic_get_input_bus_fmts = nwl_bridge_atomic_get_input_bus_fmts,
 	.mode_set		= nwl_dsi_bridge_mode_set,
 	.mode_valid		= nwl_dsi_bridge_mode_valid,
 	.attach			= nwl_dsi_bridge_attach,
@@ -1171,6 +1210,7 @@
 
 	ret = nwl_dsi_select_input(dsi);
 	if (ret < 0) {
+		pm_runtime_disable(dev);
 		mipi_dsi_host_unregister(&dsi->dsi_host);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/nxp-ptn3460.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/nxp-ptn3460.c
@@ -54,13 +54,13 @@
 	int ret;
 
 	ret = i2c_master_send(ptn_bridge->client, &addr, 1);
-	if (ret <= 0) {
+	if (ret < 0) {
 		DRM_ERROR("Failed to send i2c command, ret=%d\n", ret);
 		return ret;
 	}
 
 	ret = i2c_master_recv(ptn_bridge->client, buf, len);
-	if (ret <= 0) {
+	if (ret < 0) {
 		DRM_ERROR("Failed to recv i2c data, ret=%d\n", ret);
 		return ret;
 	}
@@ -78,7 +78,7 @@
 	buf[1] = val;
 
 	ret = i2c_master_send(ptn_bridge->client, buf, ARRAY_SIZE(buf));
-	if (ret <= 0) {
+	if (ret < 0) {
 		DRM_ERROR("Failed to send i2c command, ret=%d\n", ret);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/panel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/panel.c
@@ -9,6 +9,7 @@
 #include <drm/drm_connector.h>
 #include <drm/drm_encoder.h>
 #include <drm/drm_modeset_helper_vtables.h>
+#include <drm/drm_of.h>
 #include <drm/drm_panel.h>
 #include <drm/drm_print.h>
 #include <drm/drm_probe_helper.h>
@@ -252,9 +253,12 @@
 
 static void devm_drm_panel_bridge_release(struct device *dev, void *res)
 {
-	struct drm_bridge **bridge = res;
+	struct drm_bridge *bridge = *(struct drm_bridge **)res;
 
-	drm_panel_bridge_remove(*bridge);
+	if (!bridge)
+		return;
+
+	drm_bridge_remove(bridge);
 }
 
 /**
@@ -332,3 +336,39 @@
 	return &panel_bridge->connector;
 }
 EXPORT_SYMBOL(drm_panel_bridge_connector);
+
+#ifdef CONFIG_OF
+/**
+ * devm_drm_of_get_bridge - Return next bridge in the chain
+ * @dev: device to tie the bridge lifetime to
+ * @np: device tree node containing encoder output ports
+ * @port: port in the device tree node
+ * @endpoint: endpoint in the device tree node
+ *
+ * Given a DT node's port and endpoint number, finds the connected node
+ * and returns the associated bridge if any, or creates and returns a
+ * drm panel bridge instance if a panel is connected.
+ *
+ * Returns a pointer to the bridge if successful, or an error pointer
+ * otherwise.
+ */
+struct drm_bridge *devm_drm_of_get_bridge(struct device *dev,
+					  struct device_node *np,
+					  u32 port, u32 endpoint)
+{
+	struct drm_bridge *bridge;
+	struct drm_panel *panel;
+	int ret;
+
+	ret = drm_of_find_panel_or_bridge(np, port, endpoint,
+					  &panel, &bridge);
+	if (ret)
+		return ERR_PTR(ret);
+
+	if (panel)
+		bridge = devm_drm_panel_bridge_add(dev, panel);
+
+	return bridge;
+}
+EXPORT_SYMBOL(devm_drm_of_get_bridge);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/parade-ps8640.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/parade-ps8640.c
@@ -333,8 +333,8 @@
 	if (IS_ERR(ps_bridge->panel_bridge))
 		return PTR_ERR(ps_bridge->panel_bridge);
 
-	ps_bridge->supplies[0].supply = "vdd33";
-	ps_bridge->supplies[1].supply = "vdd12";
+	ps_bridge->supplies[0].supply = "vdd12";
+	ps_bridge->supplies[1].supply = "vdd33";
 	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ps_bridge->supplies),
 				      ps_bridge->supplies);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/sii902x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/sii902x.c
@@ -998,11 +998,6 @@
 			return ret;
 	}
 
-	sii902x->bridge.funcs = &sii902x_bridge_funcs;
-	sii902x->bridge.of_node = dev->of_node;
-	sii902x->bridge.timings = &default_sii902x_timings;
-	drm_bridge_add(&sii902x->bridge);
-
 	sii902x_audio_codec_init(sii902x, dev);
 
 	i2c_set_clientdata(sii902x->i2c, sii902x);
@@ -1015,7 +1010,16 @@
 		return -ENOMEM;
 
 	sii902x->i2cmux->priv = sii902x;
-	return i2c_mux_add_adapter(sii902x->i2cmux, 0, 0, 0);
+	ret = i2c_mux_add_adapter(sii902x->i2cmux, 0, 0, 0);
+	if (ret)
+		return ret;
+
+	sii902x->bridge.funcs = &sii902x_bridge_funcs;
+	sii902x->bridge.of_node = dev->of_node;
+	sii902x->bridge.timings = &default_sii902x_timings;
+	drm_bridge_add(&sii902x->bridge);
+
+	return 0;
 }
 
 static int sii902x_probe(struct i2c_client *client,
@@ -1075,12 +1079,11 @@
 }
 
 static int sii902x_remove(struct i2c_client *client)
-
 {
 	struct sii902x *sii902x = i2c_get_clientdata(client);
 
-	i2c_mux_del_adapters(sii902x->i2cmux);
 	drm_bridge_remove(&sii902x->bridge);
+	i2c_mux_del_adapters(sii902x->i2cmux);
 	regulator_bulk_disable(ARRAY_SIZE(sii902x->supplies),
 			       sii902x->supplies);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/sil-sii8620.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/sil-sii8620.c
@@ -605,7 +605,7 @@
 	u8 *buf = &ctx->burst.tx_buf[ctx->burst.tx_count];
 	int size = len + 2;
 
-	if (ctx->burst.tx_count + size > ARRAY_SIZE(ctx->burst.tx_buf)) {
+	if (ctx->burst.tx_count + size >= ARRAY_SIZE(ctx->burst.tx_buf)) {
 		dev_err(ctx->dev, "TX-BLK buffer exhausted\n");
 		ctx->error = -EINVAL;
 		return NULL;
@@ -622,7 +622,7 @@
 	u8 *buf = &ctx->burst.rx_buf[ctx->burst.rx_count];
 	int size = len + 1;
 
-	if (ctx->burst.tx_count + size > ARRAY_SIZE(ctx->burst.tx_buf)) {
+	if (ctx->burst.rx_count + size >= ARRAY_SIZE(ctx->burst.rx_buf)) {
 		dev_err(ctx->dev, "RX-BLK buffer exhausted\n");
 		ctx->error = -EINVAL;
 		return NULL;
@@ -2120,7 +2120,7 @@
 	if (ret) {
 		dev_err(ctx->dev, "Failed to register RC device\n");
 		ctx->error = ret;
-		rc_free_device(ctx->rc_dev);
+		rc_free_device(rc_dev);
 		return;
 	}
 	ctx->rc_dev = rc_dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/synopsys/dw-hdmi-ahb-audio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/synopsys/dw-hdmi-ahb-audio.c
@@ -320,13 +320,17 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	struct snd_dw_hdmi *dw = substream->private_data;
 	void __iomem *base = dw->data.base;
+	u8 *eld;
 	int ret;
 
 	runtime->hw = dw_hdmi_hw;
 
-	ret = snd_pcm_hw_constraint_eld(runtime, dw->data.eld);
-	if (ret < 0)
-		return ret;
+	eld = dw->data.get_eld(dw->data.hdmi);
+	if (eld) {
+		ret = snd_pcm_hw_constraint_eld(runtime, eld);
+		if (ret < 0)
+			return ret;
+	}
 
 	ret = snd_pcm_limit_hw_rates(runtime);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/synopsys/dw-hdmi-audio.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/synopsys/dw-hdmi-audio.h
@@ -9,15 +9,15 @@
 	void __iomem *base;
 	int irq;
 	struct dw_hdmi *hdmi;
-	u8 *eld;
+	u8 *(*get_eld)(struct dw_hdmi *hdmi);
 };
 
 struct dw_hdmi_i2s_audio_data {
 	struct dw_hdmi *hdmi;
-	u8 *eld;
 
 	void (*write)(struct dw_hdmi *hdmi, u8 val, int offset);
 	u8 (*read)(struct dw_hdmi *hdmi, int offset);
+	u8 *(*get_eld)(struct dw_hdmi *hdmi);
 };
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio.c
@@ -135,8 +135,15 @@
 			       size_t len)
 {
 	struct dw_hdmi_i2s_audio_data *audio = data;
+	u8 *eld;
+
+	eld = audio->get_eld(audio->hdmi);
+	if (eld)
+		memcpy(buf, eld, min_t(size_t, MAX_ELD_BYTES, len));
+	else
+		/* Pass en empty ELD if connector not available */
+		memset(buf, 0, len);
 
-	memcpy(buf, audio->eld, min_t(size_t, MAX_ELD_BYTES, len));
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
@@ -757,6 +757,14 @@
 	hdmi_writeb(hdmi, hdmi->mc_clkdis, HDMI_MC_CLKDIS);
 }
 
+static u8 *hdmi_audio_get_eld(struct dw_hdmi *hdmi)
+{
+	if (!hdmi->curr_conn)
+		return NULL;
+
+	return hdmi->curr_conn->eld;
+}
+
 static void dw_hdmi_ahb_audio_enable(struct dw_hdmi *hdmi)
 {
 	hdmi_set_cts_n(hdmi, hdmi->audio_cts, hdmi->audio_n);
@@ -2543,8 +2551,9 @@
 	if (!output_fmts)
 		return NULL;
 
-	/* If dw-hdmi is the only bridge, avoid negociating with ourselves */
-	if (list_is_singular(&bridge->encoder->bridge_chain)) {
+	/* If dw-hdmi is the first or only bridge, avoid negociating with ourselves */
+	if (list_is_singular(&bridge->encoder->bridge_chain) ||
+	    list_is_first(&bridge->chain_node, &bridge->encoder->bridge_chain)) {
 		*num_output_fmts = 1;
 		output_fmts[0] = MEDIA_BUS_FMT_FIXED;
 
@@ -2585,6 +2594,9 @@
 	 * if supported. In any case the default RGB888 format is added
 	 */
 
+	/* Default 8bit RGB fallback */
+	output_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
+
 	if (max_bpc >= 16 && info->bpc == 16) {
 		if (info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
 			output_fmts[i++] = MEDIA_BUS_FMT_YUV16_1X48;
@@ -2618,9 +2630,6 @@
 	if (info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
 		output_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
 
-	/* Default 8bit RGB fallback */
-	output_fmts[i++] = MEDIA_BUS_FMT_RGB888_1X24;
-
 	*num_output_fmts = i;
 
 	return output_fmts;
@@ -2961,6 +2970,7 @@
 {
 	struct dw_hdmi *hdmi = dev_id;
 	u8 intr_stat, phy_int_pol, phy_pol_mask, phy_stat;
+	enum drm_connector_status status = connector_status_unknown;
 
 	intr_stat = hdmi_readb(hdmi, HDMI_IH_PHY_STAT0);
 	phy_int_pol = hdmi_readb(hdmi, HDMI_PHY_POL0);
@@ -2999,13 +3009,15 @@
 			cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
 			mutex_unlock(&hdmi->cec_notifier_mutex);
 		}
-	}
 
-	if (intr_stat & HDMI_IH_PHY_STAT0_HPD) {
-		enum drm_connector_status status = phy_int_pol & HDMI_PHY_HPD
-						 ? connector_status_connected
-						 : connector_status_disconnected;
+		if (phy_stat & HDMI_PHY_HPD)
+			status = connector_status_connected;
+
+		if (!(phy_stat & (HDMI_PHY_HPD | HDMI_PHY_RX_SENSE)))
+			status = connector_status_disconnected;
+	}
 
+	if (status != connector_status_unknown) {
 		dev_dbg(hdmi->dev, "EVENT=%s\n",
 			status == connector_status_connected ?
 			"plugin" : "plugout");
@@ -3431,7 +3443,7 @@
 		audio.base = hdmi->regs;
 		audio.irq = irq;
 		audio.hdmi = hdmi;
-		audio.eld = hdmi->connector.eld;
+		audio.get_eld = hdmi_audio_get_eld;
 		hdmi->enable_audio = dw_hdmi_ahb_audio_enable;
 		hdmi->disable_audio = dw_hdmi_ahb_audio_disable;
 
@@ -3444,7 +3456,7 @@
 		struct dw_hdmi_i2s_audio_data audio;
 
 		audio.hdmi	= hdmi;
-		audio.eld	= hdmi->connector.eld;
+		audio.get_eld	= hdmi_audio_get_eld;
 		audio.write	= hdmi_writeb;
 		audio.read	= hdmi_readb;
 		hdmi->enable_audio = dw_hdmi_i2s_audio_enable;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
@@ -1199,6 +1199,7 @@
 	ret = mipi_dsi_host_register(&dsi->dsi_host);
 	if (ret) {
 		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
+		pm_runtime_disable(dev);
 		dw_mipi_dsi_debugfs_remove(dsi);
 		return ERR_PTR(ret);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/tc358762.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/tc358762.c
@@ -224,7 +224,7 @@
 	dsi->lanes = 1;
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
-			  MIPI_DSI_MODE_LPM;
+			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_VIDEO_HSE;
 
 	ret = tc358762_parse_dt(ctx);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/tc358764.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/tc358764.c
@@ -181,7 +181,7 @@
 	if (ret >= 0)
 		le32_to_cpus(val);
 
-	dev_dbg(ctx->dev, "read: %d, addr: %d\n", addr, *val);
+	dev_dbg(ctx->dev, "read: addr=0x%04x data=0x%08x\n", addr, *val);
 }
 
 static void tc358764_write(struct tc358764 *ctx, u16 addr, u32 val)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/tc358767.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/tc358767.c
@@ -1319,6 +1319,13 @@
 				struct drm_connector *connector)
 {
 	struct tc_data *tc = bridge_to_tc(bridge);
+	int ret;
+
+	ret = tc_get_display_props(tc);
+	if (ret < 0) {
+		dev_err(tc->dev, "failed to read display props: %d\n", ret);
+		return 0;
+	}
 
 	return drm_get_edid(connector, &tc->aux.ddc);
 }
@@ -1527,7 +1534,7 @@
 		dev_err(tc->dev, "syserr %x\n", stat);
 	}
 
-	if (tc->hpd_pin >= 0 && tc->bridge.dev) {
+	if (tc->hpd_pin >= 0 && tc->bridge.dev && tc->aux.drm_dev) {
 		/*
 		 * H is triggered when the GPIO goes high.
 		 *
@@ -1549,19 +1556,12 @@
 	return IRQ_HANDLED;
 }
 
-static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
+static int tc_probe_edp_bridge_endpoint(struct tc_data *tc)
 {
-	struct device *dev = &client->dev;
+	struct device *dev = tc->dev;
 	struct drm_panel *panel;
-	struct tc_data *tc;
 	int ret;
 
-	tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
-	if (!tc)
-		return -ENOMEM;
-
-	tc->dev = dev;
-
 	/* port@2 is the output port */
 	ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, NULL);
 	if (ret && ret != -ENODEV)
@@ -1580,6 +1580,25 @@
 		tc->bridge.type = DRM_MODE_CONNECTOR_DisplayPort;
 	}
 
+	return 0;
+}
+
+static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct tc_data *tc;
+	int ret;
+
+	tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
+	if (!tc)
+		return -ENOMEM;
+
+	tc->dev = dev;
+
+	ret = tc_probe_edp_bridge_endpoint(tc);
+	if (ret)
+		return ret;
+
 	/* Shut down GPIO is optional */
 	tc->sd_gpio = devm_gpiod_get_optional(dev, "shutdown", GPIOD_OUT_HIGH);
 	if (IS_ERR(tc->sd_gpio))
@@ -1621,7 +1640,7 @@
 	} else {
 		if (tc->hpd_pin < 0 || tc->hpd_pin > 1) {
 			dev_err(dev, "failed to parse HPD number\n");
-			return ret;
+			return -EINVAL;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/tc358768.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/tc358768.c
@@ -9,6 +9,8 @@
 #include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/kernel.h>
+#include <linux/media-bus-format.h>
+#include <linux/minmax.h>
 #include <linux/module.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
@@ -122,6 +124,9 @@
 #define TC358768_DSI_CONFW_MODE_CLR	(6 << 29)
 #define TC358768_DSI_CONFW_ADDR_DSI_CONTROL	(0x3 << 24)
 
+/* TC358768_DSICMD_TX (0x0600) register */
+#define TC358768_DSI_CMDTX_DC_START	BIT(0)
+
 static const char * const tc358768_supplies[] = {
 	"vddc", "vddmipi", "vddio"
 };
@@ -147,6 +152,7 @@
 
 	u32 pd_lines; /* number of Parallel Port Input Data Lines */
 	u32 dsi_lanes; /* number of DSI Lanes */
+	u32 dsi_bpp; /* number of Bits Per Pixel over DSI */
 
 	/* Parameters for PLL programming */
 	u32 fbd;	/* PLL feedback divider */
@@ -214,12 +220,31 @@
 	u32 tmp, orig;
 
 	tc358768_read(priv, reg, &orig);
+
+	if (priv->error)
+		return;
+
 	tmp = orig & ~mask;
 	tmp |= val & mask;
 	if (tmp != orig)
 		tc358768_write(priv, reg, tmp);
 }
 
+static void tc358768_dsicmd_tx(struct tc358768_priv *priv)
+{
+	u32 val;
+
+	/* start transfer */
+	tc358768_write(priv, TC358768_DSICMD_TX, TC358768_DSI_CMDTX_DC_START);
+	if (priv->error)
+		return;
+
+	/* wait transfer completion */
+	priv->error = regmap_read_poll_timeout(priv->regmap, TC358768_DSICMD_TX, val,
+					       (val & TC358768_DSI_CMDTX_DC_START) == 0,
+					       100, 100000);
+}
+
 static int tc358768_sw_reset(struct tc358768_priv *priv)
 {
 	/* Assert Reset */
@@ -279,12 +304,12 @@
 
 static u32 tc358768_pll_to_pclk(struct tc358768_priv *priv, u32 pll_clk)
 {
-	return (u32)div_u64((u64)pll_clk * priv->dsi_lanes, priv->pd_lines);
+	return (u32)div_u64((u64)pll_clk * priv->dsi_lanes, priv->dsi_bpp);
 }
 
 static u32 tc358768_pclk_to_pll(struct tc358768_priv *priv, u32 pclk)
 {
-	return (u32)div_u64((u64)pclk * priv->pd_lines, priv->dsi_lanes);
+	return (u32)div_u64((u64)pclk * priv->dsi_bpp, priv->dsi_lanes);
 }
 
 static int tc358768_calc_pll(struct tc358768_priv *priv,
@@ -329,13 +354,17 @@
 		u32 fbd;
 
 		for (fbd = 0; fbd < 512; ++fbd) {
-			u32 pll, diff;
+			u32 pll, diff, pll_in;
 
 			pll = (u32)div_u64((u64)refclk * (fbd + 1), divisor);
 
 			if (pll >= max_pll || pll < min_pll)
 				continue;
 
+			pll_in = (u32)div_u64((u64)refclk, prd + 1);
+			if (pll_in < 4000000)
+				continue;
+
 			diff = max(pll, target_pll) - min(pll, target_pll);
 
 			if (diff < best_diff) {
@@ -417,6 +446,7 @@
 	priv->output.panel = panel;
 
 	priv->dsi_lanes = dev->lanes;
+	priv->dsi_bpp = mipi_dsi_pixel_format_to_bpp(dev->format);
 
 	/* get input ep (port0/endpoint0) */
 	ret = -EINVAL;
@@ -428,7 +458,7 @@
 	}
 
 	if (ret)
-		priv->pd_lines = mipi_dsi_pixel_format_to_bpp(dev->format);
+		priv->pd_lines = priv->dsi_bpp;
 
 	drm_bridge_add(&priv->bridge);
 
@@ -495,8 +525,7 @@
 		}
 	}
 
-	/* start transfer */
-	tc358768_write(priv, TC358768_DSICMD_TX, 1);
+	tc358768_dsicmd_tx(priv);
 
 	ret = tc358768_clear_error(priv);
 	if (ret)
@@ -625,12 +654,19 @@
 {
 	struct tc358768_priv *priv = bridge_to_tc358768(bridge);
 	struct mipi_dsi_device *dsi_dev = priv->output.dev;
+	unsigned long mode_flags = dsi_dev->mode_flags;
 	u32 val, val2, lptxcnt, hact, data_type;
+	s32 raw_val;
 	const struct drm_display_mode *mode;
 	u32 dsibclk_nsk, dsiclk_nsk, ui_nsk, phy_delay_nsk;
 	u32 dsiclk, dsibclk;
 	int ret, i;
 
+	if (mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) {
+		dev_warn_once(priv->dev, "Non-continuous mode unimplemented, falling back to continuous\n");
+		mode_flags &= ~MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	}
+
 	tc358768_hw_enable(priv);
 
 	ret = tc358768_sw_reset(priv);
@@ -719,25 +755,26 @@
 
 	/* 38ns < TCLK_PREPARE < 95ns */
 	val = tc358768_ns_to_cnt(65, dsibclk_nsk) - 1;
-	/* TCLK_PREPARE > 300ns */
-	val2 = tc358768_ns_to_cnt(300 + tc358768_to_ns(3 * ui_nsk),
-				  dsibclk_nsk);
-	val |= (val2 - tc358768_to_ns(phy_delay_nsk - dsibclk_nsk)) << 8;
+	/* TCLK_PREPARE + TCLK_ZERO > 300ns */
+	val2 = tc358768_ns_to_cnt(300 - tc358768_to_ns(2 * ui_nsk),
+				  dsibclk_nsk) - 2;
+	val |= val2 << 8;
 	dev_dbg(priv->dev, "TCLK_HEADERCNT: 0x%x\n", val);
 	tc358768_write(priv, TC358768_TCLK_HEADERCNT, val);
 
-	/* TCLK_TRAIL > 60ns + 3*UI */
-	val = 60 + tc358768_to_ns(3 * ui_nsk);
-	val = tc358768_ns_to_cnt(val, dsibclk_nsk) - 5;
+	/* TCLK_TRAIL > 60ns AND TEOT <= 105 ns + 12*UI */
+	raw_val = tc358768_ns_to_cnt(60 + tc358768_to_ns(2 * ui_nsk), dsibclk_nsk) - 5;
+	val = clamp(raw_val, 0, 127);
 	dev_dbg(priv->dev, "TCLK_TRAILCNT: 0x%x\n", val);
 	tc358768_write(priv, TC358768_TCLK_TRAILCNT, val);
 
 	/* 40ns + 4*UI < THS_PREPARE < 85ns + 6*UI */
 	val = 50 + tc358768_to_ns(4 * ui_nsk);
 	val = tc358768_ns_to_cnt(val, dsibclk_nsk) - 1;
-	/* THS_ZERO > 145ns + 10*UI */
-	val2 = tc358768_ns_to_cnt(145 - tc358768_to_ns(ui_nsk), dsibclk_nsk);
-	val |= (val2 - tc358768_to_ns(phy_delay_nsk)) << 8;
+	/* THS_PREPARE + THS_ZERO > 145ns + 10*UI */
+	raw_val = tc358768_ns_to_cnt(145 - tc358768_to_ns(3 * ui_nsk), dsibclk_nsk) - 10;
+	val2 = clamp(raw_val, 0, 127);
+	val |= val2 << 8;
 	dev_dbg(priv->dev, "THS_HEADERCNT: 0x%x\n", val);
 	tc358768_write(priv, TC358768_THS_HEADERCNT, val);
 
@@ -753,9 +790,10 @@
 	dev_dbg(priv->dev, "TCLK_POSTCNT: 0x%x\n", val);
 	tc358768_write(priv, TC358768_TCLK_POSTCNT, val);
 
-	/* 60ns + 4*UI < THS_PREPARE < 105ns + 12*UI */
-	val = tc358768_ns_to_cnt(60 + tc358768_to_ns(15 * ui_nsk),
-				 dsibclk_nsk) - 5;
+	/* max(60ns + 4*UI, 8*UI) < THS_TRAILCNT < 105ns + 12*UI */
+	raw_val = tc358768_ns_to_cnt(60 + tc358768_to_ns(18 * ui_nsk),
+				     dsibclk_nsk) - 4;
+	val = clamp(raw_val, 0, 15);
 	dev_dbg(priv->dev, "THS_TRAILCNT: 0x%x\n", val);
 	tc358768_write(priv, TC358768_THS_TRAILCNT, val);
 
@@ -764,12 +802,12 @@
 		val |= BIT(i + 1);
 	tc358768_write(priv, TC358768_HSTXVREGEN, val);
 
-	if (!(dsi_dev->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS))
-		tc358768_write(priv, TC358768_TXOPTIONCNTRL, 0x1);
+	tc358768_write(priv, TC358768_TXOPTIONCNTRL,
+		       (mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) ? 0 : BIT(0));
 
 	/* TXTAGOCNT[26:16] RXTASURECNT[10:0] */
 	val = tc358768_to_ns((lptxcnt + 1) * dsibclk_nsk * 4);
-	val = tc358768_ns_to_cnt(val, dsibclk_nsk) - 1;
+	val = tc358768_ns_to_cnt(val, dsibclk_nsk) / 4 - 1;
 	val2 = tc358768_ns_to_cnt(tc358768_to_ns((lptxcnt + 1) * dsibclk_nsk),
 				  dsibclk_nsk) - 2;
 	val |= val2 << 16;
@@ -801,11 +839,12 @@
 	tc358768_write(priv, TC358768_DSI_HACT, hact);
 
 	/* VSYNC polarity */
-	if (!(mode->flags & DRM_MODE_FLAG_NVSYNC))
-		tc358768_update_bits(priv, TC358768_CONFCTL, BIT(5), BIT(5));
+	tc358768_update_bits(priv, TC358768_CONFCTL, BIT(5),
+			     (mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIT(5) : 0);
+
 	/* HSYNC polarity */
-	if (mode->flags & DRM_MODE_FLAG_PHSYNC)
-		tc358768_update_bits(priv, TC358768_PP_MISC, BIT(0), BIT(0));
+	tc358768_update_bits(priv, TC358768_PP_MISC, BIT(0),
+			     (mode->flags & DRM_MODE_FLAG_PHSYNC) ? BIT(0) : 0);
 
 	/* Start DSI Tx */
 	tc358768_write(priv, TC358768_DSI_START, 0x1);
@@ -819,10 +858,9 @@
 	val = TC358768_DSI_CONFW_MODE_SET | TC358768_DSI_CONFW_ADDR_DSI_CONTROL;
 	val |= (dsi_dev->lanes - 1) << 1;
 
-	if (!(dsi_dev->mode_flags & MIPI_DSI_MODE_LPM))
-		val |= TC358768_DSI_CONTROL_TXMD;
+	val |= TC358768_DSI_CONTROL_TXMD;
 
-	if (!(dsi_dev->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS))
+	if (!(mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS))
 		val |= TC358768_DSI_CONTROL_HSCKMD;
 
 	if (dsi_dev->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET)
@@ -866,6 +904,44 @@
 	}
 }
 
+#define MAX_INPUT_SEL_FORMATS	1
+
+static u32 *
+tc358768_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+				   struct drm_bridge_state *bridge_state,
+				   struct drm_crtc_state *crtc_state,
+				   struct drm_connector_state *conn_state,
+				   u32 output_fmt,
+				   unsigned int *num_input_fmts)
+{
+	struct tc358768_priv *priv = bridge_to_tc358768(bridge);
+	u32 *input_fmts;
+
+	*num_input_fmts = 0;
+
+	input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts),
+			     GFP_KERNEL);
+	if (!input_fmts)
+		return NULL;
+
+	switch (priv->pd_lines) {
+	case 16:
+		input_fmts[0] = MEDIA_BUS_FMT_RGB565_1X16;
+		break;
+	case 18:
+		input_fmts[0] = MEDIA_BUS_FMT_RGB666_1X18;
+		break;
+	default:
+	case 24:
+		input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24;
+		break;
+	};
+
+	*num_input_fmts = MAX_INPUT_SEL_FORMATS;
+
+	return input_fmts;
+}
+
 static const struct drm_bridge_funcs tc358768_bridge_funcs = {
 	.attach = tc358768_bridge_attach,
 	.mode_valid = tc358768_bridge_mode_valid,
@@ -873,6 +949,11 @@
 	.enable = tc358768_bridge_enable,
 	.disable = tc358768_bridge_disable,
 	.post_disable = tc358768_bridge_post_disable,
+
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
+	.atomic_get_input_bus_fmts = tc358768_atomic_get_input_bus_fmts,
 };
 
 static const struct drm_bridge_timings default_tc358768_timings = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/tc358775.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/tc358775.c
@@ -453,10 +453,6 @@
 	dev_dbg(tc->dev, "bus_formats %04x bpc %d\n",
 		connector->display_info.bus_formats[0],
 		tc->bpc);
-	/*
-	 * Default hardware register settings of tc358775 configured
-	 * with MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA jeida-24 format
-	 */
 	if (connector->display_info.bus_formats[0] ==
 		MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) {
 		/* VESA-24 */
@@ -467,14 +463,15 @@
 		d2l_write(tc->i2c, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2));
 		d2l_write(tc->i2c, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
 		d2l_write(tc->i2c, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6));
-	} else { /*  MEDIA_BUS_FMT_RGB666_1X7X3_SPWG - JEIDA-18 */
-		d2l_write(tc->i2c, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
-		d2l_write(tc->i2c, LV_MX0407, LV_MX(LVI_R4, LVI_L0, LVI_R5, LVI_G0));
-		d2l_write(tc->i2c, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_L0, LVI_L0));
-		d2l_write(tc->i2c, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0));
-		d2l_write(tc->i2c, LV_MX1619, LV_MX(LVI_L0, LVI_L0, LVI_B1, LVI_B2));
-		d2l_write(tc->i2c, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
-		d2l_write(tc->i2c, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_L0));
+	} else {
+		/* JEIDA-18 and JEIDA-24 */
+		d2l_write(tc->i2c, LV_MX0003, LV_MX(LVI_R2, LVI_R3, LVI_R4, LVI_R5));
+		d2l_write(tc->i2c, LV_MX0407, LV_MX(LVI_R6, LVI_R1, LVI_R7, LVI_G2));
+		d2l_write(tc->i2c, LV_MX0811, LV_MX(LVI_G3, LVI_G4, LVI_G0, LVI_G1));
+		d2l_write(tc->i2c, LV_MX1215, LV_MX(LVI_G5, LVI_G6, LVI_G7, LVI_B2));
+		d2l_write(tc->i2c, LV_MX1619, LV_MX(LVI_B0, LVI_B1, LVI_B3, LVI_B4));
+		d2l_write(tc->i2c, LV_MX2023, LV_MX(LVI_B5, LVI_B6, LVI_B7, LVI_L0));
+		d2l_write(tc->i2c, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R0));
 	}
 
 	d2l_write(tc->i2c, VFUEN, VFUEN_EN);
@@ -605,10 +602,8 @@
 						};
 
 	host = of_find_mipi_dsi_host_by_node(tc->host_node);
-	if (!host) {
-		dev_err(dev, "failed to find dsi host\n");
-		return -EPROBE_DEFER;
-	}
+	if (!host)
+		return dev_err_probe(dev, -EPROBE_DEFER, "failed to find dsi host\n");
 
 	dsi = mipi_dsi_device_register_full(host, &info);
 	if (IS_ERR(dsi)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/ti-sn65dsi83.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/ti-sn65dsi83.c
@@ -272,7 +272,9 @@
 
 	dsi->lanes = ctx->dsi_lanes;
 	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+			  MIPI_DSI_MODE_VIDEO_NO_HFP | MIPI_DSI_MODE_VIDEO_NO_HBP |
+			  MIPI_DSI_MODE_VIDEO_NO_HSA | MIPI_DSI_MODE_NO_EOT_PACKET;
 
 	ret = mipi_dsi_attach(dsi);
 	if (ret < 0) {
@@ -381,6 +383,8 @@
 	u16 val;
 	int ret;
 
+	usleep_range(10000, 11000);
+
 	/* Get the LVDS format from the bridge state. */
 	bridge_state = drm_atomic_get_new_bridge_state(state, bridge);
 
@@ -608,10 +612,14 @@
 	ctx->host_node = of_graph_get_remote_port_parent(endpoint);
 	of_node_put(endpoint);
 
-	if (ctx->dsi_lanes < 0 || ctx->dsi_lanes > 4)
-		return -EINVAL;
-	if (!ctx->host_node)
-		return -ENODEV;
+	if (ctx->dsi_lanes <= 0 || ctx->dsi_lanes > 4) {
+		ret = -EINVAL;
+		goto err_put_node;
+	}
+	if (!ctx->host_node) {
+		ret = -ENODEV;
+		goto err_put_node;
+	}
 
 	ctx->lvds_dual_link = false;
 	ctx->lvds_dual_link_even_odd_swap = false;
@@ -638,16 +646,22 @@
 
 	ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, &panel_bridge);
 	if (ret < 0)
-		return ret;
+		goto err_put_node;
 	if (panel) {
 		panel_bridge = devm_drm_panel_bridge_add(dev, panel);
-		if (IS_ERR(panel_bridge))
-			return PTR_ERR(panel_bridge);
+		if (IS_ERR(panel_bridge)) {
+			ret = PTR_ERR(panel_bridge);
+			goto err_put_node;
+		}
 	}
 
 	ctx->panel_bridge = panel_bridge;
 
 	return 0;
+
+err_put_node:
+	of_node_put(ctx->host_node);
+	return ret;
 }
 
 static int sn65dsi83_probe(struct i2c_client *client,
@@ -680,8 +694,10 @@
 		return ret;
 
 	ctx->regmap = devm_regmap_init_i2c(client, &sn65dsi83_regmap_config);
-	if (IS_ERR(ctx->regmap))
-		return PTR_ERR(ctx->regmap);
+	if (IS_ERR(ctx->regmap)) {
+		ret = PTR_ERR(ctx->regmap);
+		goto err_put_node;
+	}
 
 	dev_set_drvdata(dev, ctx);
 	i2c_set_clientdata(client, ctx);
@@ -691,6 +707,10 @@
 	drm_bridge_add(&ctx->bridge);
 
 	return 0;
+
+err_put_node:
+	of_node_put(ctx->host_node);
+	return ret;
 }
 
 static int sn65dsi83_remove(struct i2c_client *client)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/ti-sn65dsi86.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/ti-sn65dsi86.c
@@ -147,9 +147,9 @@
  *                each other's read-modify-write.
  */
 struct ti_sn65dsi86 {
-	struct auxiliary_device		bridge_aux;
-	struct auxiliary_device		gpio_aux;
-	struct auxiliary_device		aux_aux;
+	struct auxiliary_device		*bridge_aux;
+	struct auxiliary_device		*gpio_aux;
+	struct auxiliary_device		*aux_aux;
 
 	struct device			*dev;
 	struct regmap			*regmap;
@@ -188,6 +188,7 @@
 	.val_bits = 8,
 	.volatile_table = &ti_sn_bridge_volatile_table,
 	.cache_type = REGCACHE_NONE,
+	.max_register = 0xFF,
 };
 
 static void ti_sn65dsi86_write_u16(struct ti_sn65dsi86 *pdata,
@@ -411,27 +412,36 @@
 	auxiliary_device_delete(data);
 }
 
-/*
- * AUX bus docs say that a non-NULL release is mandatory, but it makes no
- * sense for the model used here where all of the aux devices are allocated
- * in the single shared structure. We'll use this noop as a workaround.
- */
-static void ti_sn65dsi86_noop(struct device *dev) {}
+static void ti_sn65dsi86_aux_device_release(struct device *dev)
+{
+	struct auxiliary_device *aux = container_of(dev, struct auxiliary_device, dev);
+
+	kfree(aux);
+}
 
 static int ti_sn65dsi86_add_aux_device(struct ti_sn65dsi86 *pdata,
-				       struct auxiliary_device *aux,
+				       struct auxiliary_device **aux_out,
 				       const char *name)
 {
 	struct device *dev = pdata->dev;
+	const struct i2c_client *client = to_i2c_client(dev);
+	struct auxiliary_device *aux;
 	int ret;
 
+	aux = kzalloc(sizeof(*aux), GFP_KERNEL);
+	if (!aux)
+		return -ENOMEM;
+
 	aux->name = name;
+	aux->id = (client->adapter->nr << 10) | client->addr;
 	aux->dev.parent = dev;
-	aux->dev.release = ti_sn65dsi86_noop;
+	aux->dev.release = ti_sn65dsi86_aux_device_release;
 	device_set_of_node_from_dev(&aux->dev, dev);
 	ret = auxiliary_device_init(aux);
-	if (ret)
+	if (ret) {
+		kfree(aux);
 		return ret;
+	}
 	ret = devm_add_action_or_reset(dev, ti_sn65dsi86_uninit_aux, aux);
 	if (ret)
 		return ret;
@@ -440,6 +450,8 @@
 	if (ret)
 		return ret;
 	ret = devm_add_action_or_reset(dev, ti_sn65dsi86_delete_aux, aux);
+	if (!ret)
+		*aux_out = aux;
 
 	return ret;
 }
@@ -461,6 +473,7 @@
 	u32 request_val = AUX_CMD_REQ(msg->request);
 	u8 *buf = msg->buffer;
 	unsigned int len = msg->size;
+	unsigned int short_len;
 	unsigned int val;
 	int ret;
 	u8 addr_len[SN_AUX_LENGTH_REG + 1 - SN_AUX_ADDR_19_16_REG];
@@ -534,7 +547,8 @@
 	}
 
 	if (val & AUX_IRQ_STATUS_AUX_SHORT) {
-		ret = regmap_read(pdata->regmap, SN_AUX_LENGTH_REG, &len);
+		ret = regmap_read(pdata->regmap, SN_AUX_LENGTH_REG, &short_len);
+		len = min(len, short_len);
 		if (ret)
 			goto exit;
 	} else if (val & AUX_IRQ_STATUS_NAT_I2C_FAIL) {
@@ -919,9 +933,9 @@
 		&pdata->bridge.encoder->crtc->state->adjusted_mode;
 	u8 hsync_polarity = 0, vsync_polarity = 0;
 
-	if (mode->flags & DRM_MODE_FLAG_PHSYNC)
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
 		hsync_polarity = CHA_HSYNC_POLARITY;
-	if (mode->flags & DRM_MODE_FLAG_PVSYNC)
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
 		vsync_polarity = CHA_VSYNC_POLARITY;
 
 	ti_sn65dsi86_write_u16(pdata, SN_CHA_ACTIVE_LINE_LENGTH_LOW_REG,
@@ -1472,6 +1486,7 @@
 
 static void ti_sn65dsi86_runtime_disable(void *data)
 {
+	pm_runtime_dont_use_autosuspend(data);
 	pm_runtime_disable(data);
 }
 
@@ -1531,11 +1546,11 @@
 				     "failed to get reference clock\n");
 
 	pm_runtime_enable(dev);
+	pm_runtime_set_autosuspend_delay(pdata->dev, 500);
+	pm_runtime_use_autosuspend(pdata->dev);
 	ret = devm_add_action_or_reset(dev, ti_sn65dsi86_runtime_disable, dev);
 	if (ret)
 		return ret;
-	pm_runtime_set_autosuspend_delay(pdata->dev, 500);
-	pm_runtime_use_autosuspend(pdata->dev);
 
 	ti_sn65dsi86_debugfs_init(pdata);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/bridge/ti-tpd12s015.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/bridge/ti-tpd12s015.c
@@ -179,7 +179,7 @@
 	return 0;
 }
 
-static int __exit tpd12s015_remove(struct platform_device *pdev)
+static int tpd12s015_remove(struct platform_device *pdev)
 {
 	struct tpd12s015_device *tpd = platform_get_drvdata(pdev);
 
@@ -197,7 +197,7 @@
 
 static struct platform_driver tpd12s015_driver = {
 	.probe	= tpd12s015_probe,
-	.remove	= __exit_p(tpd12s015_remove),
+	.remove = tpd12s015_remove,
 	.driver	= {
 		.name	= "tpd12s015",
 		.of_match_table = tpd12s015_of_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_aperture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_aperture.c
@@ -329,7 +329,20 @@
 						     const struct drm_driver *req_driver)
 {
 	resource_size_t base, size;
-	int bar, ret = 0;
+	int bar, ret;
+
+	/*
+	 * WARNING: Apparently we must kick fbdev drivers before vgacon,
+	 * otherwise the vga fbdev driver falls over.
+	 */
+#if IS_REACHABLE(CONFIG_FB)
+	ret = remove_conflicting_pci_framebuffers(pdev, req_driver->name);
+	if (ret)
+		return ret;
+#endif
+	ret = vga_remove_vgacon(pdev);
+	if (ret)
+		return ret;
 
 	for (bar = 0; bar < PCI_STD_NUM_BARS; ++bar) {
 		if (!(pci_resource_flags(pdev, bar) & IORESOURCE_MEM))
@@ -339,15 +352,6 @@
 		drm_aperture_detach_drivers(base, size);
 	}
 
-	/*
-	 * WARNING: Apparently we must kick fbdev drivers before vgacon,
-	 * otherwise the vga fbdev driver falls over.
-	 */
-#if IS_REACHABLE(CONFIG_FB)
-	ret = remove_conflicting_pci_framebuffers(pdev, req_driver->name);
-#endif
-	if (ret == 0)
-		ret = vga_remove_vgacon(pdev);
-	return ret;
+	return 0;
 }
 EXPORT_SYMBOL(drm_aperture_remove_conflicting_pci_framebuffers);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_atomic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_atomic.c
@@ -138,6 +138,12 @@
 	if (!state->planes)
 		goto fail;
 
+	/*
+	 * Because drm_atomic_state can be committed asynchronously we need our
+	 * own reference and cannot rely on the on implied by drm_file in the
+	 * ioctl call.
+	 */
+	drm_dev_get(dev);
 	state->dev = dev;
 
 	DRM_DEBUG_ATOMIC("Allocated atomic state %p\n", state);
@@ -297,7 +303,8 @@
 void __drm_atomic_state_free(struct kref *ref)
 {
 	struct drm_atomic_state *state = container_of(ref, typeof(*state), ref);
-	struct drm_mode_config *config = &state->dev->mode_config;
+	struct drm_device *dev = state->dev;
+	struct drm_mode_config *config = &dev->mode_config;
 
 	drm_atomic_state_clear(state);
 
@@ -309,6 +316,8 @@
 		drm_atomic_state_default_release(state);
 		kfree(state);
 	}
+
+	drm_dev_put(dev);
 }
 EXPORT_SYMBOL(__drm_atomic_state_free);
 
@@ -1052,6 +1061,7 @@
 	drm_printf(p, "connector[%u]: %s\n", connector->base.id, connector->name);
 	drm_printf(p, "\tcrtc=%s\n", state->crtc ? state->crtc->name : "(null)");
 	drm_printf(p, "\tself_refresh_aware=%d\n", state->self_refresh_aware);
+	drm_printf(p, "\tmax_requested_bpc=%d\n", state->max_requested_bpc);
 
 	if (connector->connector_type == DRM_MODE_CONNECTOR_WRITEBACK)
 		if (state->writeback_job && state->writeback_job->fb)
@@ -1310,8 +1320,10 @@
 
 	DRM_DEBUG_ATOMIC("checking %p\n", state);
 
-	for_each_new_crtc_in_state(state, crtc, new_crtc_state, i)
-		requested_crtc |= drm_crtc_mask(crtc);
+	for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
+		if (new_crtc_state->enable)
+			requested_crtc |= drm_crtc_mask(crtc);
+	}
 
 	for_each_oldnew_plane_in_state(state, plane, old_plane_state, new_plane_state, i) {
 		ret = drm_atomic_plane_check(old_plane_state, new_plane_state);
@@ -1360,8 +1372,10 @@
 		}
 	}
 
-	for_each_new_crtc_in_state(state, crtc, new_crtc_state, i)
-		affected_crtc |= drm_crtc_mask(crtc);
+	for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
+		if (new_crtc_state->enable)
+			affected_crtc |= drm_crtc_mask(crtc);
+	}
 
 	/*
 	 * For commits that allow modesets drivers can add other CRTCs to the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_atomic_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_atomic_helper.c
@@ -285,7 +285,8 @@
 update_connector_routing(struct drm_atomic_state *state,
 			 struct drm_connector *connector,
 			 struct drm_connector_state *old_connector_state,
-			 struct drm_connector_state *new_connector_state)
+			 struct drm_connector_state *new_connector_state,
+			 bool added_by_user)
 {
 	const struct drm_connector_helper_funcs *funcs;
 	struct drm_encoder *new_encoder;
@@ -336,9 +337,13 @@
 	 * there's a chance the connector may have been destroyed during the
 	 * process, but it's better to ignore that then cause
 	 * drm_atomic_helper_resume() to fail.
+	 *
+	 * Last, we want to ignore connector registration when the connector
+	 * was not pulled in the atomic state by user-space (ie, was pulled
+	 * in by the driver, e.g. when updating a DP-MST stream).
 	 */
 	if (!state->duplicated && drm_connector_is_unregistered(connector) &&
-	    crtc_state->active) {
+	    added_by_user && crtc_state->active) {
 		DRM_DEBUG_ATOMIC("[CONNECTOR:%d:%s] is not registered\n",
 				 connector->base.id, connector->name);
 		return -EINVAL;
@@ -610,7 +615,10 @@
 	struct drm_connector *connector;
 	struct drm_connector_state *old_connector_state, *new_connector_state;
 	int i, ret;
-	unsigned int connectors_mask = 0;
+	unsigned int connectors_mask = 0, user_connectors_mask = 0;
+
+	for_each_oldnew_connector_in_state(state, connector, old_connector_state, new_connector_state, i)
+		user_connectors_mask |= BIT(i);
 
 	for_each_oldnew_crtc_in_state(state, crtc, old_crtc_state, new_crtc_state, i) {
 		bool has_connectors =
@@ -675,7 +683,8 @@
 		 */
 		ret = update_connector_routing(state, connector,
 					       old_connector_state,
-					       new_connector_state);
+					       new_connector_state,
+					       BIT(i) & user_connectors_mask);
 		if (ret)
 			return ret;
 		if (old_connector_state->crtc) {
@@ -996,12 +1005,22 @@
 		return drm_atomic_crtc_effectively_active(old_state);
 
 	/*
-	 * We need to run through the crtc_funcs->disable() function if the CRTC
-	 * is currently on, if it's transitioning to self refresh mode, or if
-	 * it's in self refresh mode and needs to be fully disabled.
+	 * We need to disable bridge(s) and CRTC if we're transitioning out of
+	 * self-refresh and changing CRTCs at the same time, because the
+	 * bridge tracks self-refresh status via CRTC state.
+	 */
+	if (old_state->self_refresh_active &&
+	    old_state->crtc != new_state->crtc)
+		return true;
+
+	/*
+	 * We also need to run through the crtc_funcs->disable() function if
+	 * the CRTC is currently on, if it's transitioning to self refresh
+	 * mode, or if it's in self refresh mode and needs to be fully
+	 * disabled.
 	 */
 	return old_state->active ||
-	       (old_state->self_refresh_active && !new_state->enable) ||
+	       (old_state->self_refresh_active && !new_state->active) ||
 	       new_state->self_refresh_active;
 }
 
@@ -1105,7 +1124,16 @@
 			continue;
 
 		ret = drm_crtc_vblank_get(crtc);
-		WARN_ONCE(ret != -EINVAL, "driver forgot to call drm_crtc_vblank_off()\n");
+		/*
+		 * Self-refresh is not a true "disable"; ensure vblank remains
+		 * enabled.
+		 */
+		if (new_crtc_state->self_refresh_active)
+			WARN_ONCE(ret != 0,
+				  "driver disabled vblank in self-refresh\n");
+		else
+			WARN_ONCE(ret != -EINVAL,
+				  "driver forgot to call drm_crtc_vblank_off()\n");
 		if (ret == 0)
 			drm_crtc_vblank_put(crtc);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_atomic_state_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_atomic_state_helper.c
@@ -474,6 +474,9 @@
 	if (state->hdr_output_metadata)
 		drm_property_blob_get(state->hdr_output_metadata);
 
+	if (state->gen_hdr_output_metadata)
+		drm_property_blob_get(state->gen_hdr_output_metadata);
+
 	/* Don't copy over a writeback job, they are used only once */
 	state->writeback_job = NULL;
 }
@@ -523,6 +526,7 @@
 		drm_writeback_cleanup_job(state->writeback_job);
 
 	drm_property_blob_put(state->hdr_output_metadata);
+	drm_property_blob_put(state->gen_hdr_output_metadata);
 }
 EXPORT_SYMBOL(__drm_atomic_helper_connector_destroy_state);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_atomic_uapi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_atomic_uapi.c
@@ -76,15 +76,17 @@
 	state->mode_blob = NULL;
 
 	if (mode) {
+		struct drm_property_blob *blob;
+
 		drm_mode_convert_to_umode(&umode, mode);
-		state->mode_blob =
-			drm_property_create_blob(state->crtc->dev,
-						 sizeof(umode),
-						 &umode);
-		if (IS_ERR(state->mode_blob))
-			return PTR_ERR(state->mode_blob);
+		blob = drm_property_create_blob(crtc->dev,
+						sizeof(umode), &umode);
+		if (IS_ERR(blob))
+			return PTR_ERR(blob);
 
 		drm_mode_copy(&state->mode, mode);
+
+		state->mode_blob = blob;
 		state->enable = true;
 		drm_dbg_atomic(crtc->dev,
 			       "Set [MODE:%s] for [CRTC:%d:%s] state %p\n",
@@ -601,7 +603,7 @@
 					&state->fb_damage_clips,
 					val,
 					-1,
-					sizeof(struct drm_rect),
+					sizeof(struct drm_mode_rect),
 					&replaced);
 		return ret;
 	} else if (property == plane->scaling_filter_property) {
@@ -765,6 +767,13 @@
 				sizeof(struct hdr_output_metadata), -1,
 				&replaced);
 		return ret;
+	} else if (property == config->gen_hdr_output_metadata_property) {
+		ret = drm_atomic_replace_property_blob_from_id(dev,
+				&state->gen_hdr_output_metadata,
+				val,
+				sizeof(struct gen_hdr_output_metadata), -1,
+				&replaced);
+		return ret;
 	} else if (property == config->aspect_ratio_property) {
 		state->picture_aspect_ratio = val;
 	} else if (property == config->content_type_property) {
@@ -863,6 +872,9 @@
 	} else if (property == config->hdr_output_metadata_property) {
 		*val = state->hdr_output_metadata ?
 			state->hdr_output_metadata->base.id : 0;
+	} else if (property == config->gen_hdr_output_metadata_property) {
+		*val = state->gen_hdr_output_metadata ?
+			state->gen_hdr_output_metadata->base.id : 0;
 	} else if (property == config->content_protection_property) {
 		*val = state->content_protection;
 	} else if (property == config->hdcp_content_type_property) {
@@ -962,6 +974,10 @@
 
 	if (mode != DRM_MODE_DPMS_ON)
 		mode = DRM_MODE_DPMS_OFF;
+
+	if (connector->dpms == mode)
+		goto out;
+
 	connector->dpms = mode;
 
 	crtc = connector->state->crtc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_bridge.c
@@ -28,6 +28,7 @@
 #include <drm/drm_atomic_state_helper.h>
 #include <drm/drm_bridge.h>
 #include <drm/drm_encoder.h>
+#include <drm/drm_of.h>
 #include <drm/drm_print.h>
 
 #include "drm_crtc_internal.h"
@@ -51,10 +52,8 @@
  *
  * Display drivers are responsible for linking encoders with the first bridge
  * in the chains. This is done by acquiring the appropriate bridge with
- * of_drm_find_bridge() or drm_of_find_panel_or_bridge(), or creating it for a
- * panel with drm_panel_bridge_add_typed() (or the managed version
- * devm_drm_panel_bridge_add_typed()). Once acquired, the bridge shall be
- * attached to the encoder with a call to drm_bridge_attach().
+ * devm_drm_of_get_bridge(). Once acquired, the bridge shall be attached to the
+ * encoder with a call to drm_bridge_attach().
  *
  * Bridges are responsible for linking themselves with the next bridge in the
  * chain, if any. This is done the same way as for encoders, with the call to
@@ -763,8 +762,8 @@
 				    struct drm_connector_state *conn_state,
 				    u32 out_bus_fmt)
 {
+	unsigned int i, num_in_bus_fmts = 0;
 	struct drm_bridge_state *cur_state;
-	unsigned int num_in_bus_fmts, i;
 	struct drm_bridge *prev_bridge;
 	u32 *in_bus_fmts;
 	int ret;
@@ -885,7 +884,7 @@
 	struct drm_connector *conn = conn_state->connector;
 	struct drm_encoder *encoder = bridge->encoder;
 	struct drm_bridge_state *last_bridge_state;
-	unsigned int i, num_out_bus_fmts;
+	unsigned int i, num_out_bus_fmts = 0;
 	struct drm_bridge *last_bridge;
 	u32 *out_bus_fmts;
 	int ret = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_bridge_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_bridge_connector.c
@@ -369,8 +369,10 @@
 				    connector_type, ddc);
 	drm_connector_helper_add(connector, &drm_bridge_connector_helper_funcs);
 
-	if (bridge_connector->bridge_hpd)
+	if (bridge_connector->bridge_hpd) {
 		connector->polled = DRM_CONNECTOR_POLL_HPD;
+		drm_bridge_connector_enable_hpd(connector);
+	}
 	else if (bridge_connector->bridge_detect)
 		connector->polled = DRM_CONNECTOR_POLL_CONNECT
 				  | DRM_CONNECTOR_POLL_DISCONNECT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_client_modeset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_client_modeset.c
@@ -309,6 +309,9 @@
 	can_clone = true;
 	dmt_mode = drm_mode_find_dmt(dev, 1024, 768, 60, false);
 
+	if (!dmt_mode)
+		goto fail;
+
 	for (i = 0; i < connector_count; i++) {
 		if (!enabled[i])
 			continue;
@@ -324,11 +327,13 @@
 		if (!modes[i])
 			can_clone = false;
 	}
+	kfree(dmt_mode);
 
 	if (can_clone) {
 		DRM_DEBUG_KMS("can clone using 1024x768\n");
 		return true;
 	}
+fail:
 	DRM_INFO("kms: can't enable cloning when we probably wanted to.\n");
 	return false;
 }
@@ -770,6 +775,7 @@
 	unsigned int total_modes_count = 0;
 	struct drm_client_offset *offsets;
 	unsigned int connector_count = 0;
+	/* points to modes protected by mode_config.mutex */
 	struct drm_display_mode **modes;
 	struct drm_crtc **crtcs;
 	int i, ret = 0;
@@ -838,7 +844,6 @@
 		drm_client_pick_crtcs(client, connectors, connector_count,
 				      crtcs, modes, 0, width, height);
 	}
-	mutex_unlock(&dev->mode_config.mutex);
 
 	drm_client_modeset_release(client);
 
@@ -860,13 +865,20 @@
 				break;
 			}
 
+			kfree(modeset->mode);
 			modeset->mode = drm_mode_duplicate(dev, mode);
+			if (!modeset->mode) {
+				ret = -ENOMEM;
+				break;
+			}
+
 			drm_connector_get(connector);
 			modeset->connectors[modeset->num_connectors++] = connector;
 			modeset->x = offset->x;
 			modeset->y = offset->y;
 		}
 	}
+	mutex_unlock(&dev->mode_config.mutex);
 
 	mutex_unlock(&client->modeset_mutex);
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_connector.c
@@ -487,6 +487,9 @@
 	mutex_destroy(&connector->mutex);
 
 	memset(connector, 0, sizeof(*connector));
+
+	if (dev->registered)
+		drm_sysfs_hotplug_event(dev);
 }
 EXPORT_SYMBOL(drm_connector_cleanup);
 
@@ -977,6 +980,10 @@
  * 	callback. For atomic drivers the remapping to the "ACTIVE" property is
  * 	implemented in the DRM core.
  *
+ * 	On atomic drivers any DPMS setproperty ioctl where the value does not
+ * 	change is completely skipped, otherwise a full atomic commit will occur.
+ * 	On legacy drivers the exact behavior is driver specific.
+ *
  * 	Note that this property cannot be set through the MODE_ATOMIC ioctl,
  * 	userspace must use "ACTIVE" on the CRTC instead.
  *
@@ -1190,6 +1197,14 @@
  *	hdmi_drm_infoframe_pack() to pack the infoframe as per spec, in case of
  *	HDMI encoder.
  *
+ * GEN_HDR_OUTPUT_METADATA:
+ *  This connector property is functionally the same as HDR_OUTPUT_METADATA.
+ *  However, the existing structures for HDR_OUTPUT_METADATA are not flexible
+ *  enough for dynamic HDR or other connectivity devices like SDI. So, this
+ *  property was created to utilize more generic structures that would be
+ *  scalable in the future. This is currently experimental and may possibly
+ *  be merged with the original HDR_OUTPUT_METADATA property in the future.
+ *
  * max bpc:
  *	This range property is used by userspace to limit the bit depth. When
  *	used the driver would limit the bpc in accordance with the valid range
@@ -1300,6 +1315,12 @@
 		return -ENOMEM;
 	dev->mode_config.hdr_output_metadata_property = prop;
 
+	prop = drm_property_create(dev, DRM_MODE_PROP_BLOB,
+				   "GEN_HDR_OUTPUT_METADATA", 0);
+	if (!prop)
+		return -ENOMEM;
+	dev->mode_config.gen_hdr_output_metadata_property = prop;
+
 	return 0;
 }
 
@@ -2233,6 +2254,9 @@
 void drm_connector_set_vrr_capable_property(
 		struct drm_connector *connector, bool capable)
 {
+	if (!connector->vrr_capable_property)
+		return;
+
 	drm_object_property_set_value(&connector->base,
 				      connector->vrr_capable_property,
 				      capable);
@@ -2454,7 +2478,7 @@
 						     dev->mode_config.max_width,
 						     dev->mode_config.max_height);
 		else
-			drm_dbg_kms(dev, "User-space requested a forced probe on [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe",
+			drm_dbg_kms(dev, "User-space requested a forced probe on [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe\n",
 				    connector->base.id, connector->name);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_crtc.c
@@ -643,8 +643,7 @@
 	struct drm_mode_set set;
 	uint32_t __user *set_connectors_ptr;
 	struct drm_modeset_acquire_ctx ctx;
-	int ret;
-	int i;
+	int ret, i, num_connectors = 0;
 
 	if (!drm_core_check_feature(dev, DRIVER_MODESET))
 		return -EOPNOTSUPP;
@@ -799,6 +798,7 @@
 					connector->name);
 
 			connector_set[i] = connector;
+			num_connectors++;
 		}
 	}
 
@@ -807,7 +807,7 @@
 	set.y = crtc_req->y;
 	set.mode = mode;
 	set.connectors = connector_set;
-	set.num_connectors = crtc_req->count_connectors;
+	set.num_connectors = num_connectors;
 	set.fb = fb;
 
 	if (drm_drv_uses_atomic_modeset(dev))
@@ -820,7 +820,7 @@
 		drm_framebuffer_put(fb);
 
 	if (connector_set) {
-		for (i = 0; i < crtc_req->count_connectors; i++) {
+		for (i = 0; i < num_connectors; i++) {
 			if (connector_set[i])
 				drm_connector_put(connector_set[i]);
 		}
@@ -832,6 +832,7 @@
 	connector_set = NULL;
 	fb = NULL;
 	mode = NULL;
+	num_connectors = 0;
 
 	DRM_MODESET_LOCK_ALL_END(dev, ctx, ret);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_displayid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_displayid.c
@@ -7,13 +7,28 @@
 #include <drm/drm_edid.h>
 #include <drm/drm_print.h>
 
+static const struct displayid_header *
+displayid_get_header(const u8 *displayid, int length, int index)
+{
+	const struct displayid_header *base;
+
+	if (sizeof(*base) > length - index)
+		return ERR_PTR(-EINVAL);
+
+	base = (const struct displayid_header *)&displayid[index];
+
+	return base;
+}
+
 static int validate_displayid(const u8 *displayid, int length, int idx)
 {
 	int i, dispid_length;
 	u8 csum = 0;
 	const struct displayid_header *base;
 
-	base = (const struct displayid_header *)&displayid[idx];
+	base = displayid_get_header(displayid, length, idx);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
 
 	DRM_DEBUG_KMS("base revision 0x%x, length %d, %d %d\n",
 		      base->rev, base->bytes, base->prod_id, base->ext_count);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_dp_aux_bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_dp_aux_bus.c
@@ -66,7 +66,6 @@
  * @dev: The device to remove.
  *
  * Calls through to the endpoint driver remove.
- *
  */
 static void dp_aux_ep_remove(struct device *dev)
 {
@@ -120,8 +119,6 @@
 /**
  * dp_aux_ep_dev_release() - Free memory for the dp_aux_ep device
  * @dev: The device to free.
- *
- * Return: 0 if no error or negative error code.
  */
 static void dp_aux_ep_dev_release(struct device *dev)
 {
@@ -256,6 +253,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(of_dp_aux_populate_ep_devices);
 
 static void of_dp_aux_depopulate_ep_devices_void(void *data)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_dp_cec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_dp_cec.c
@@ -310,16 +310,6 @@
 	if (!aux->transfer)
 		return;
 
-#ifndef CONFIG_MEDIA_CEC_RC
-	/*
-	 * CEC_CAP_RC is part of CEC_CAP_DEFAULTS, but it is stripped by
-	 * cec_allocate_adapter() if CONFIG_MEDIA_CEC_RC is undefined.
-	 *
-	 * Do this here as well to ensure the tests against cec_caps are
-	 * correct.
-	 */
-	cec_caps &= ~CEC_CAP_RC;
-#endif
 	cancel_delayed_work_sync(&aux->cec.unregister_work);
 
 	mutex_lock(&aux->cec.lock);
@@ -336,7 +326,9 @@
 		num_las = CEC_MAX_LOG_ADDRS;
 
 	if (aux->cec.adap) {
-		if (aux->cec.adap->capabilities == cec_caps &&
+		/* Check if the adapter properties have changed */
+		if ((aux->cec.adap->capabilities & CEC_CAP_MONITOR_ALL) ==
+		    (cec_caps & CEC_CAP_MONITOR_ALL) &&
 		    aux->cec.adap->available_log_addrs == num_las) {
 			/* Unchanged, so just set the phys addr */
 			cec_s_phys_addr_from_edid(aux->cec.adap, edid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_dp_dual_mode_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_dp_dual_mode_helper.c
@@ -63,23 +63,45 @@
 ssize_t drm_dp_dual_mode_read(struct i2c_adapter *adapter,
 			      u8 offset, void *buffer, size_t size)
 {
+	u8 zero = 0;
+	char *tmpbuf = NULL;
+	/*
+	 * As sub-addressing is not supported by all adaptors,
+	 * always explicitly read from the start and discard
+	 * any bytes that come before the requested offset.
+	 * This way, no matter whether the adaptor supports it
+	 * or not, we'll end up reading the proper data.
+	 */
 	struct i2c_msg msgs[] = {
 		{
 			.addr = DP_DUAL_MODE_SLAVE_ADDRESS,
 			.flags = 0,
 			.len = 1,
-			.buf = &offset,
+			.buf = &zero,
 		},
 		{
 			.addr = DP_DUAL_MODE_SLAVE_ADDRESS,
 			.flags = I2C_M_RD,
-			.len = size,
+			.len = size + offset,
 			.buf = buffer,
 		},
 	};
 	int ret;
 
+	if (offset) {
+		tmpbuf = kmalloc(size + offset, GFP_KERNEL);
+		if (!tmpbuf)
+			return -ENOMEM;
+
+		msgs[1].buf = tmpbuf;
+	}
+
 	ret = i2c_transfer(adapter, msgs, ARRAY_SIZE(msgs));
+	if (tmpbuf)
+		memcpy(buffer, tmpbuf + offset, size);
+
+	kfree(tmpbuf);
+
 	if (ret < 0)
 		return ret;
 	if (ret != ARRAY_SIZE(msgs))
@@ -208,18 +230,6 @@
 	if (ret)
 		return DRM_DP_DUAL_MODE_UNKNOWN;
 
-	/*
-	 * Sigh. Some (maybe all?) type 1 adaptors are broken and ack
-	 * the offset but ignore it, and instead they just always return
-	 * data from the start of the HDMI ID buffer. So for a broken
-	 * type 1 HDMI adaptor a single byte read will always give us
-	 * 0x44, and for a type 1 DVI adaptor it should give 0x00
-	 * (assuming it implements any registers). Fortunately neither
-	 * of those values will match the type 2 signature of the
-	 * DP_DUAL_MODE_ADAPTOR_ID register so we can proceed with
-	 * the type 2 adaptor detection safely even in the presence
-	 * of broken type 1 adaptors.
-	 */
 	ret = drm_dp_dual_mode_read(adapter, DP_DUAL_MODE_ADAPTOR_ID,
 				    &adaptor_id, sizeof(adaptor_id));
 	drm_dbg_kms(dev, "DP dual mode adaptor ID: %02x (err %zd)\n", adaptor_id, ret);
@@ -233,11 +243,10 @@
 				return DRM_DP_DUAL_MODE_TYPE2_DVI;
 		}
 		/*
-		 * If neither a proper type 1 ID nor a broken type 1 adaptor
-		 * as described above, assume type 1, but let the user know
-		 * that we may have misdetected the type.
+		 * If not a proper type 1 ID, still assume type 1, but let
+		 * the user know that we may have misdetected the type.
 		 */
-		if (!is_type1_adaptor(adaptor_id) && adaptor_id != hdmi_id[0])
+		if (!is_type1_adaptor(adaptor_id))
 			drm_err(dev, "Unexpected DP dual mode adaptor ID %02x\n", adaptor_id);
 
 	}
@@ -343,10 +352,8 @@
  * @enable: enable (as opposed to disable) the TMDS output buffers
  *
  * Set the state of the TMDS output buffers in the adaptor. For
- * type2 this is set via the DP_DUAL_MODE_TMDS_OEN register. As
- * some type 1 adaptors have problems with registers (see comments
- * in drm_dp_dual_mode_detect()) we avoid touching the register,
- * making this function a no-op on type 1 adaptors.
+ * type2 this is set via the DP_DUAL_MODE_TMDS_OEN register.
+ * Type1 adaptors do not support any register writes.
  *
  * Returns:
  * 0 on success, negative error code on failure
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_dp_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_dp_helper.c
@@ -1801,8 +1801,6 @@
 {
 	int ret;
 
-	WARN_ON_ONCE(!aux->drm_dev);
-
 	if (!aux->ddc.algo)
 		drm_dp_aux_init(aux);
 
@@ -2376,17 +2374,8 @@
 				struct drm_dp_phy_test_params *data, u8 dp_rev)
 {
 	int err, i;
-	u8 link_config[2];
 	u8 test_pattern;
 
-	link_config[0] = drm_dp_link_rate_to_bw_code(data->link_rate);
-	link_config[1] = data->num_lanes;
-	if (data->enhanced_frame_cap)
-		link_config[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
-	err = drm_dp_dpcd_write(aux, DP_LINK_BW_SET, link_config, 2);
-	if (err < 0)
-		return err;
-
 	test_pattern = data->phy_pattern;
 	if (dp_rev < 0x12) {
 		test_pattern = (test_pattern << 2) &
@@ -3214,27 +3203,13 @@
 			     const u16 level)
 {
 	int ret;
-	u8 dpcd_buf, new_dpcd_buf;
-
-	ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf);
-	if (ret != 1) {
-		drm_dbg_kms(aux->drm_dev,
-			    "%s: Failed to read backlight mode: %d\n", aux->name, ret);
-		return ret < 0 ? ret : -EIO;
-	}
+	u8 dpcd_buf = DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
 
-	new_dpcd_buf = dpcd_buf;
-
-	if ((dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) != DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
-		new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK;
-		new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
-
-		if (bl->pwmgen_bit_count) {
-			ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, bl->pwmgen_bit_count);
-			if (ret != 1)
-				drm_dbg_kms(aux->drm_dev, "%s: Failed to write aux pwmgen bit count: %d\n",
-					    aux->name, ret);
-		}
+	if (bl->pwmgen_bit_count) {
+		ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, bl->pwmgen_bit_count);
+		if (ret != 1)
+			drm_dbg_kms(aux->drm_dev, "%s: Failed to write aux pwmgen bit count: %d\n",
+				    aux->name, ret);
 	}
 
 	if (bl->pwm_freq_pre_divider) {
@@ -3244,16 +3219,14 @@
 				    "%s: Failed to write aux backlight frequency: %d\n",
 				    aux->name, ret);
 		else
-			new_dpcd_buf |= DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
+			dpcd_buf |= DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
 	}
 
-	if (new_dpcd_buf != dpcd_buf) {
-		ret = drm_dp_dpcd_writeb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf);
-		if (ret != 1) {
-			drm_dbg_kms(aux->drm_dev, "%s: Failed to write aux backlight mode: %d\n",
-				    aux->name, ret);
-			return ret < 0 ? ret : -EIO;
-		}
+	ret = drm_dp_dpcd_writeb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER, dpcd_buf);
+	if (ret != 1) {
+		drm_dbg_kms(aux->drm_dev, "%s: Failed to write aux backlight mode: %d\n",
+			    aux->name, ret);
+		return ret < 0 ? ret : -EIO;
 	}
 
 	ret = drm_edp_backlight_set_level(aux, bl, level);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_dp_mst_topology.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_dp_mst_topology.c
@@ -178,13 +178,13 @@
 drm_dp_mst_rad_to_str(const u8 rad[8], u8 lct, char *out, size_t len)
 {
 	int i;
-	u8 unpacked_rad[16];
+	u8 unpacked_rad[16] = {};
 
-	for (i = 0; i < lct; i++) {
+	for (i = 1; i < lct; i++) {
 		if (i % 2)
-			unpacked_rad[i] = rad[i / 2] >> 4;
+			unpacked_rad[i] = rad[(i - 1) / 2] >> 4;
 		else
-			unpacked_rad[i] = rad[i / 2] & BIT_MASK(4);
+			unpacked_rad[i] = rad[(i - 1) / 2] & 0xF;
 	}
 
 	/* TODO: Eventually add something to printk so we can format the rad
@@ -319,6 +319,9 @@
 	hdr->broadcast = (buf[idx] >> 7) & 0x1;
 	hdr->path_msg = (buf[idx] >> 6) & 0x1;
 	hdr->msg_len = buf[idx] & 0x3f;
+	if (hdr->msg_len < 1)		/* min space for body CRC */
+		return false;
+
 	idx++;
 	hdr->somt = (buf[idx] >> 7) & 0x1;
 	hdr->eomt = (buf[idx] >> 6) & 0x1;
@@ -2615,14 +2618,14 @@
 	struct drm_dp_mst_branch *found_mstb;
 	struct drm_dp_mst_port *port;
 
+	if (!mstb)
+		return NULL;
+
 	if (memcmp(mstb->guid, guid, 16) == 0)
 		return mstb;
 
 
 	list_for_each_entry(port, &mstb->ports, next) {
-		if (!port->mstb)
-			continue;
-
 		found_mstb = get_mst_branch_device_by_guid_helper(port->mstb, guid);
 
 		if (found_mstb)
@@ -2974,7 +2977,7 @@
 
 	/* FIXME: Actually do some real error handling here */
 	ret = drm_dp_mst_wait_tx_reply(mstb, txmsg);
-	if (ret <= 0) {
+	if (ret < 0) {
 		drm_err(mgr->dev, "Sending link address failed with %d\n", ret);
 		goto out;
 	}
@@ -3026,7 +3029,7 @@
 	mutex_unlock(&mgr->lock);
 
 out:
-	if (ret <= 0)
+	if (ret < 0)
 		mstb->link_address_sent = false;
 	kfree(txmsg);
 	return ret < 0 ? ret : changed;
@@ -3781,6 +3784,9 @@
 		set_bit(0, &mgr->payload_mask);
 		mgr->vcpi_mask = 0;
 		mgr->payload_id_table_cleared = false;
+
+		memset(&mgr->down_rep_recv, 0, sizeof(mgr->down_rep_recv));
+		memset(&mgr->up_req_recv, 0, sizeof(mgr->up_req_recv));
 	}
 
 out_unlock:
@@ -3860,9 +3866,7 @@
 	if (!mgr->mst_primary)
 		goto out_fail;
 
-	ret = drm_dp_dpcd_read(mgr->aux, DP_DPCD_REV, mgr->dpcd,
-			       DP_RECEIVER_CAP_SIZE);
-	if (ret != DP_RECEIVER_CAP_SIZE) {
+	if (drm_dp_read_dpcd_caps(mgr->aux, mgr->dpcd) < 0) {
 		drm_dbg_kms(mgr->dev, "dpcd read failed - undocked during suspend?\n");
 		goto out_fail;
 	}
@@ -3989,6 +3993,34 @@
 	return true;
 }
 
+static int get_msg_request_type(u8 data)
+{
+	return data & 0x7f;
+}
+
+static bool verify_rx_request_type(struct drm_dp_mst_topology_mgr *mgr,
+				   const struct drm_dp_sideband_msg_tx *txmsg,
+				   const struct drm_dp_sideband_msg_rx *rxmsg)
+{
+	const struct drm_dp_sideband_msg_hdr *hdr = &rxmsg->initial_hdr;
+	const struct drm_dp_mst_branch *mstb = txmsg->dst;
+	int tx_req_type = get_msg_request_type(txmsg->msg[0]);
+	int rx_req_type = get_msg_request_type(rxmsg->msg[0]);
+	char rad_str[64];
+
+	if (tx_req_type == rx_req_type)
+		return true;
+
+	drm_dp_mst_rad_to_str(mstb->rad, mstb->lct, rad_str, sizeof(rad_str));
+	drm_dbg_kms(mgr->dev,
+		    "Got unexpected MST reply, mstb: %p seqno: %d lct: %d rad: %s rx_req_type: %s (%02x) != tx_req_type: %s (%02x)\n",
+		    mstb, hdr->seqno, mstb->lct, rad_str,
+		    drm_dp_mst_req_type_str(rx_req_type), rx_req_type,
+		    drm_dp_mst_req_type_str(tx_req_type), tx_req_type);
+
+	return false;
+}
+
 static int drm_dp_mst_handle_down_rep(struct drm_dp_mst_topology_mgr *mgr)
 {
 	struct drm_dp_sideband_msg_tx *txmsg;
@@ -3996,7 +4028,7 @@
 	struct drm_dp_sideband_msg_rx *msg = &mgr->down_rep_recv;
 
 	if (!drm_dp_get_one_sb_msg(mgr, false, &mstb))
-		goto out;
+		goto out_clear_reply;
 
 	/* Multi-packet message transmission, don't clear the reply */
 	if (!msg->have_eomt)
@@ -4018,6 +4050,9 @@
 		goto out_clear_reply;
 	}
 
+	if (!verify_rx_request_type(mgr, txmsg, msg))
+		goto out_clear_reply;
+
 	drm_dp_sideband_parse_reply(mgr, msg, &txmsg->reply);
 
 	if (txmsg->reply.reply_type == DP_SIDEBAND_REPLY_NAK) {
@@ -4122,9 +4157,10 @@
 static int drm_dp_mst_handle_up_req(struct drm_dp_mst_topology_mgr *mgr)
 {
 	struct drm_dp_pending_up_req *up_req;
+	struct drm_dp_mst_branch *mst_primary;
 
 	if (!drm_dp_get_one_sb_msg(mgr, true, NULL))
-		goto out;
+		goto out_clear_reply;
 
 	if (!mgr->up_req_recv.have_eomt)
 		return 0;
@@ -4142,15 +4178,25 @@
 		drm_dbg_kms(mgr->dev, "Received unknown up req type, ignoring: %x\n",
 			    up_req->msg.req_type);
 		kfree(up_req);
-		goto out;
+		goto out_clear_reply;
+	}
+
+	mutex_lock(&mgr->lock);
+	mst_primary = mgr->mst_primary;
+	if (!mst_primary || !drm_dp_mst_topology_try_get_mstb(mst_primary)) {
+		mutex_unlock(&mgr->lock);
+		kfree(up_req);
+		goto out_clear_reply;
 	}
+	mutex_unlock(&mgr->lock);
 
-	drm_dp_send_up_ack_reply(mgr, mgr->mst_primary, up_req->msg.req_type,
+	drm_dp_send_up_ack_reply(mgr, mst_primary, up_req->msg.req_type,
 				 false);
 
 	if (up_req->msg.req_type == DP_CONNECTION_STATUS_NOTIFY) {
 		const struct drm_dp_connection_status_notify *conn_stat =
 			&up_req->msg.u.conn_stat;
+		bool handle_csn;
 
 		drm_dbg_kms(mgr->dev, "Got CSN: pn: %d ldps:%d ddps: %d mcs: %d ip: %d pdt: %d\n",
 			    conn_stat->port_number,
@@ -4159,6 +4205,16 @@
 			    conn_stat->message_capability_status,
 			    conn_stat->input_port,
 			    conn_stat->peer_device_type);
+
+		mutex_lock(&mgr->probe_lock);
+		handle_csn = mst_primary->link_address_sent;
+		mutex_unlock(&mgr->probe_lock);
+
+		if (!handle_csn) {
+			drm_dbg_kms(mgr->dev, "Got CSN before finish topology probing. Skip it.");
+			kfree(up_req);
+			goto out_put_primary;
+		}
 	} else if (up_req->msg.req_type == DP_RESOURCE_STATUS_NOTIFY) {
 		const struct drm_dp_resource_status_notify *res_stat =
 			&up_req->msg.u.resource_stat;
@@ -4174,7 +4230,9 @@
 	mutex_unlock(&mgr->up_req_lock);
 	queue_work(system_long_wq, &mgr->up_req_work);
 
-out:
+out_put_primary:
+	drm_dp_mst_topology_put_mstb(mst_primary);
+out_clear_reply:
 	memset(&mgr->up_req_recv, 0, sizeof(struct drm_dp_sideband_msg_rx));
 	return 0;
 }
@@ -4834,6 +4892,7 @@
 
 	mst_edid = drm_dp_mst_get_edid(port->connector, mgr, port);
 	drm_edid_get_monitor_name(mst_edid, name, namelen);
+	kfree(mst_edid);
 }
 
 /**
@@ -4893,22 +4952,21 @@
 		u8 buf[DP_PAYLOAD_TABLE_SIZE];
 		int ret;
 
-		ret = drm_dp_dpcd_read(mgr->aux, DP_DPCD_REV, buf, DP_RECEIVER_CAP_SIZE);
-		if (ret) {
+		if (drm_dp_read_dpcd_caps(mgr->aux, buf) < 0) {
 			seq_printf(m, "dpcd read failed\n");
 			goto out;
 		}
 		seq_printf(m, "dpcd: %*ph\n", DP_RECEIVER_CAP_SIZE, buf);
 
 		ret = drm_dp_dpcd_read(mgr->aux, DP_FAUX_CAP, buf, 2);
-		if (ret) {
+		if (ret != 2) {
 			seq_printf(m, "faux/mst read failed\n");
 			goto out;
 		}
 		seq_printf(m, "faux/mst: %*ph\n", 2, buf);
 
 		ret = drm_dp_dpcd_read(mgr->aux, DP_MSTM_CTRL, buf, 1);
-		if (ret) {
+		if (ret != 1) {
 			seq_printf(m, "mst ctrl read failed\n");
 			goto out;
 		}
@@ -4916,7 +4974,7 @@
 
 		/* dump the standard OUI branch header */
 		ret = drm_dp_dpcd_read(mgr->aux, DP_BRANCH_OUI, buf, DP_BRANCH_OUI_HEADER_SIZE);
-		if (ret) {
+		if (ret != DP_BRANCH_OUI_HEADER_SIZE) {
 			seq_printf(m, "branch oui read failed\n");
 			goto out;
 		}
@@ -5287,7 +5345,7 @@
 	mst_state = drm_atomic_get_mst_topology_state(state, mgr);
 
 	if (IS_ERR(mst_state))
-		return -EINVAL;
+		return PTR_ERR(mst_state);
 
 	list_for_each_entry(pos, &mst_state->vcpis, next) {
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_drv.c
@@ -581,6 +581,7 @@
 			const struct drm_driver *driver,
 			struct device *parent)
 {
+	struct inode *inode;
 	int ret;
 
 	if (!drm_core_init_complete) {
@@ -613,17 +614,19 @@
 	mutex_init(&dev->clientlist_mutex);
 	mutex_init(&dev->master_mutex);
 
-	ret = drmm_add_action(dev, drm_dev_init_release, NULL);
+	ret = drmm_add_action_or_reset(dev, drm_dev_init_release, NULL);
 	if (ret)
 		return ret;
 
-	dev->anon_inode = drm_fs_inode_new();
-	if (IS_ERR(dev->anon_inode)) {
-		ret = PTR_ERR(dev->anon_inode);
+	inode = drm_fs_inode_new();
+	if (IS_ERR(inode)) {
+		ret = PTR_ERR(inode);
 		DRM_ERROR("Cannot allocate anonymous inode: %d\n", ret);
 		goto err;
 	}
 
+	dev->anon_inode = inode;
+
 	if (drm_core_check_feature(dev, DRIVER_RENDER)) {
 		ret = drm_minor_alloc(dev, DRM_MINOR_RENDER);
 		if (ret)
@@ -891,8 +894,11 @@
 			goto err_minors;
 	}
 
-	if (drm_core_check_feature(dev, DRIVER_MODESET))
-		drm_modeset_register_all(dev);
+	if (drm_core_check_feature(dev, DRIVER_MODESET)) {
+		ret = drm_modeset_register_all(dev);
+		if (ret)
+			goto err_unload;
+	}
 
 	DRM_INFO("Initialized %s %d.%d.%d %s for %s on minor %d\n",
 		 driver->name, driver->major, driver->minor,
@@ -902,6 +908,9 @@
 
 	goto out_unlock;
 
+err_unload:
+	if (dev->driver->unload)
+		dev->driver->unload(dev);
 err_minors:
 	remove_compat_control_link(dev);
 	drm_minor_unregister(dev, DRM_MINOR_PRIMARY);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_edid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_edid.c
@@ -1994,9 +1994,6 @@
 
 		connector_bad_edid(connector, edid, edid[0x7e] + 1);
 
-		edid[EDID_LENGTH-1] += edid[0x7e] - valid_extensions;
-		edid[0x7e] = valid_extensions;
-
 		new = kmalloc_array(valid_extensions + 1, EDID_LENGTH,
 				    GFP_KERNEL);
 		if (!new)
@@ -2013,6 +2010,9 @@
 			base += EDID_LENGTH;
 		}
 
+		new[EDID_LENGTH - 1] += new[0x7e] - valid_extensions;
+		new[0x7e] = valid_extensions;
+
 		kfree(edid);
 		edid = new;
 	}
@@ -4339,6 +4339,51 @@
 	return true;
 }
 
+static void drm_calculate_luminance_range(struct drm_connector *connector)
+{
+	struct hdr_static_metadata *hdr_metadata = &connector->hdr_sink_metadata.hdmi_type1;
+	struct drm_luminance_range_info *luminance_range =
+		&connector->display_info.luminance_range;
+	static const u8 pre_computed_values[] = {
+		50, 51, 52, 53, 55, 56, 57, 58, 59, 61, 62, 63, 65, 66, 68, 69,
+		71, 72, 74, 75, 77, 79, 81, 82, 84, 86, 88, 90, 92, 94, 96, 98
+	};
+	u32 max_avg, min_cll, max, min, q, r;
+
+	if (!(hdr_metadata->metadata_type & BIT(HDMI_STATIC_METADATA_TYPE1)))
+		return;
+
+	max_avg = hdr_metadata->max_fall;
+	min_cll = hdr_metadata->min_cll;
+
+	/*
+	 * From the specification (CTA-861-G), for calculating the maximum
+	 * luminance we need to use:
+	 *	Luminance = 50*2**(CV/32)
+	 * Where CV is a one-byte value.
+	 * For calculating this expression we may need float point precision;
+	 * to avoid this complexity level, we take advantage that CV is divided
+	 * by a constant. From the Euclids division algorithm, we know that CV
+	 * can be written as: CV = 32*q + r. Next, we replace CV in the
+	 * Luminance expression and get 50*(2**q)*(2**(r/32)), hence we just
+	 * need to pre-compute the value of r/32. For pre-computing the values
+	 * We just used the following Ruby line:
+	 *	(0...32).each {|cv| puts (50*2**(cv/32.0)).round}
+	 * The results of the above expressions can be verified at
+	 * pre_computed_values.
+	 */
+	q = max_avg >> 5;
+	r = max_avg % 32;
+	max = (1 << q) * pre_computed_values[r];
+
+	/* min luminance: maxLum * (CV/255)^2 / 100 */
+	q = DIV_ROUND_CLOSEST(min_cll, 255);
+	min = max * DIV_ROUND_CLOSEST((q * q), 100);
+
+	luminance_range->min_luminance = min;
+	luminance_range->max_luminance = max;
+}
+
 static uint8_t eotf_supported(const u8 *edid_ext)
 {
 	return edid_ext[2] &
@@ -4370,8 +4415,12 @@
 		connector->hdr_sink_metadata.hdmi_type1.max_cll = db[4];
 	if (len >= 5)
 		connector->hdr_sink_metadata.hdmi_type1.max_fall = db[5];
-	if (len >= 6)
+	if (len >= 6) {
 		connector->hdr_sink_metadata.hdmi_type1.min_cll = db[6];
+
+		/* Calculate only when all values are available */
+		drm_calculate_luminance_range(connector);
+	}
 }
 
 static void
@@ -4776,7 +4825,8 @@
 	if (!edid_ext)
 		goto end;
 
-	has_audio = ((edid_ext[3] & EDID_BASIC_AUDIO) != 0);
+	has_audio = (edid_ext[0] == CEA_EXT &&
+		    (edid_ext[3] & EDID_BASIC_AUDIO) != 0);
 
 	if (has_audio) {
 		DRM_DEBUG_KMS("Monitor has basic audio support\n");
@@ -4941,7 +4991,8 @@
 			else if (hf_vsdb[11] & DRM_EDID_DSC_10BPC)
 				hdmi_dsc->bpc_supported = 10;
 			else
-				hdmi_dsc->bpc_supported = 0;
+				/* Supports min 8 BPC if DSC 1.2 is supported*/
+				hdmi_dsc->bpc_supported = 8;
 
 			dsc_max_frl_rate = (hf_vsdb[12] & DRM_EDID_DSC_MAX_FRL_RATE_MASK) >> 4;
 			drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc->max_lanes,
@@ -5003,21 +5054,21 @@
 
 	if (hdmi[6] & DRM_EDID_HDMI_DC_30) {
 		dc_bpc = 10;
-		info->edid_hdmi_dc_modes |= DRM_EDID_HDMI_DC_30;
+		info->edid_hdmi_rgb444_dc_modes |= DRM_EDID_HDMI_DC_30;
 		DRM_DEBUG("%s: HDMI sink does deep color 30.\n",
 			  connector->name);
 	}
 
 	if (hdmi[6] & DRM_EDID_HDMI_DC_36) {
 		dc_bpc = 12;
-		info->edid_hdmi_dc_modes |= DRM_EDID_HDMI_DC_36;
+		info->edid_hdmi_rgb444_dc_modes |= DRM_EDID_HDMI_DC_36;
 		DRM_DEBUG("%s: HDMI sink does deep color 36.\n",
 			  connector->name);
 	}
 
 	if (hdmi[6] & DRM_EDID_HDMI_DC_48) {
 		dc_bpc = 16;
-		info->edid_hdmi_dc_modes |= DRM_EDID_HDMI_DC_48;
+		info->edid_hdmi_rgb444_dc_modes |= DRM_EDID_HDMI_DC_48;
 		DRM_DEBUG("%s: HDMI sink does deep color 48.\n",
 			  connector->name);
 	}
@@ -5032,16 +5083,9 @@
 		  connector->name, dc_bpc);
 	info->bpc = dc_bpc;
 
-	/*
-	 * Deep color support mandates RGB444 support for all video
-	 * modes and forbids YCRCB422 support for all video modes per
-	 * HDMI 1.3 spec.
-	 */
-	info->color_formats = DRM_COLOR_FORMAT_RGB444;
-
 	/* YCRCB444 is optional according to spec. */
 	if (hdmi[6] & DRM_EDID_HDMI_DC_Y444) {
-		info->color_formats |= DRM_COLOR_FORMAT_YCRCB444;
+		info->edid_hdmi_ycbcr444_dc_modes = info->edid_hdmi_rgb444_dc_modes;
 		DRM_DEBUG("%s: HDMI sink does YCRCB444 in deep color.\n",
 			  connector->name);
 	}
@@ -5180,6 +5224,7 @@
 
 	info->non_desktop = 0;
 	memset(&info->monitor_range, 0, sizeof(info->monitor_range));
+	memset(&info->luminance_range, 0, sizeof(info->luminance_range));
 }
 
 u32 drm_add_display_info(struct drm_connector *connector, const struct edid *edid)
@@ -5205,6 +5250,7 @@
 	if (!(edid->input & DRM_EDID_INPUT_DIGITAL))
 		return quirks;
 
+	info->color_formats |= DRM_COLOR_FORMAT_RGB444;
 	drm_parse_cea_ext(connector, edid);
 
 	/*
@@ -5253,7 +5299,6 @@
 	DRM_DEBUG("%s: Assigning EDID-1.4 digital sink color depth as %d bpc.\n",
 			  connector->name, info->bpc);
 
-	info->color_formats |= DRM_COLOR_FORMAT_RGB444;
 	if (edid->features & DRM_EDID_FEATURE_RGB_YCRCB444)
 		info->color_formats |= DRM_COLOR_FORMAT_YCRCB444;
 	if (edid->features & DRM_EDID_FEATURE_RGB_YCRCB422)
@@ -5603,8 +5648,6 @@
 static u8 drm_mode_cea_vic(const struct drm_connector *connector,
 			   const struct drm_display_mode *mode)
 {
-	u8 vic;
-
 	/*
 	 * HDMI spec says if a mode is found in HDMI 1.4b 4K modes
 	 * we should send its VIC in vendor infoframes, else send the
@@ -5614,13 +5657,18 @@
 	if (drm_mode_hdmi_vic(connector, mode))
 		return 0;
 
-	vic = drm_match_cea_mode(mode);
+	return drm_match_cea_mode(mode);
+}
 
-	/*
-	 * HDMI 1.4 VIC range: 1 <= VIC <= 64 (CEA-861-D) but
-	 * HDMI 2.0 VIC range: 1 <= VIC <= 107 (CEA-861-F). So we
-	 * have to make sure we dont break HDMI 1.4 sinks.
-	 */
+/*
+ * Avoid sending VICs defined in HDMI 2.0 in AVI infoframes to sinks that
+ * conform to HDMI 1.4.
+ *
+ * HDMI 1.4 (CTA-861-D) VIC range: [1..64]
+ * HDMI 2.0 (CTA-861-F) VIC range: [1..107]
+ */
+static u8 vic_for_avi_infoframe(const struct drm_connector *connector, u8 vic)
+{
 	if (!is_hdmi2_sink(connector) && vic > 64)
 		return 0;
 
@@ -5628,6 +5676,79 @@
 }
 
 /**
+ * drm_hdmi_infoframe_set_gen_hdr_metadata() - fill an HDMI DRM infoframe with
+ *                                             HDR metadata from userspace
+ * @frame: HDMI DRM infoframe
+ * @conn_state: Connector state containing HDR metadata
+ *
+ * Return: 0 on success or a negative error code on failure.
+ */
+int
+drm_hdmi_infoframe_set_gen_hdr_metadata(struct hdmi_drm_infoframe *frame,
+					const struct drm_connector_state *conn_state)
+{
+	struct drm_connector *connector;
+	struct gen_hdr_output_metadata *gen_hdr_metadata;
+	struct hdr_metadata_infoframe *hdr_infoframe;
+	int err;
+
+	if (!frame || !conn_state)
+		return -EINVAL;
+
+	connector = conn_state->connector;
+
+	if (!conn_state->gen_hdr_output_metadata)
+		return -EINVAL;
+
+	gen_hdr_metadata = conn_state->gen_hdr_output_metadata->data;
+
+	if (!gen_hdr_metadata || !connector)
+		return -EINVAL;
+
+	if (gen_hdr_metadata->metadata_type == DRM_HDR_TYPE_HDR10) {
+		hdr_infoframe = (struct hdr_metadata_infoframe *)
+			gen_hdr_metadata->payload;
+
+		/* Sink EOTF is Bit map while infoframe is absolute values */
+		if (!is_eotf_supported(hdr_infoframe->eotf,
+		    connector->hdr_sink_metadata.hdmi_type1.eotf)) {
+			DRM_DEBUG_KMS("EOTF Not Supported\n");
+			return -EINVAL;
+		}
+
+		err = hdmi_drm_infoframe_init(frame);
+		if (err < 0)
+			return err;
+
+		frame->eotf = hdr_infoframe->eotf;
+		frame->metadata_type = hdr_infoframe->metadata_type;
+
+		BUILD_BUG_ON(sizeof(frame->display_primaries) !=
+			     sizeof(hdr_infoframe->display_primaries));
+		BUILD_BUG_ON(sizeof(frame->white_point) !=
+			     sizeof(hdr_infoframe->white_point));
+
+		memcpy(&frame->display_primaries,
+		       &hdr_infoframe->display_primaries,
+		       sizeof(frame->display_primaries));
+
+		memcpy(&frame->white_point,
+		       &hdr_infoframe->white_point,
+		       sizeof(frame->white_point));
+
+		frame->max_display_mastering_luminance =
+			hdr_infoframe->max_display_mastering_luminance;
+		frame->min_display_mastering_luminance =
+			hdr_infoframe->min_display_mastering_luminance;
+		frame->max_fall = hdr_infoframe->max_fall;
+		frame->max_cll = hdr_infoframe->max_cll;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(drm_hdmi_infoframe_set_gen_hdr_metadata);
+
+/**
  * drm_hdmi_avi_infoframe_from_display_mode() - fill an HDMI AVI infoframe with
  *                                              data from a DRM display mode
  * @frame: HDMI AVI infoframe
@@ -5696,7 +5817,7 @@
 		picture_aspect = HDMI_PICTURE_ASPECT_NONE;
 	}
 
-	frame->video_code = vic;
+	frame->video_code = vic_for_avi_infoframe(connector, vic);
 	frame->picture_aspect = picture_aspect;
 	frame->active_aspect = HDMI_ACTIVE_ASPECT_PICTURE;
 	frame->scan_mode = HDMI_SCAN_MODE_UNDERSCAN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_fb_cma_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_fb_cma_helper.c
@@ -71,7 +71,6 @@
 	u8 h_div = 1, v_div = 1;
 	u32 block_w = drm_format_info_block_width(fb->format, plane);
 	u32 block_h = drm_format_info_block_height(fb->format, plane);
-	u32 block_size = fb->format->char_per_block[plane];
 	u32 sample_x;
 	u32 sample_y;
 	u32 block_start_y;
@@ -94,7 +93,7 @@
 	num_hblocks = sample_x / block_w;
 
 	paddr += fb->pitches[plane] * block_start_y;
-	paddr += block_size * num_hblocks;
+	paddr += drm_format_plane_width_bytes(fb->format, plane, num_hblocks);
 
 	return paddr;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_fb_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_fb_helper.c
@@ -73,7 +73,7 @@
  * considered as a broken and legacy behaviour from a modern fbdev device.
  */
 #if IS_ENABLED(CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM)
-static bool drm_leak_fbdev_smem = false;
+static bool drm_leak_fbdev_smem = true;
 module_param_unsafe(drm_leak_fbdev_smem, bool, 0600);
 MODULE_PARM_DESC(drm_leak_fbdev_smem,
 		 "Allow unsafe leaking fbdev physical smem address [default=false]");
@@ -683,22 +683,21 @@
 /**
  * drm_fb_helper_deferred_io() - fbdev deferred_io callback function
  * @info: fb_info struct pointer
- * @pagelist: list of mmap framebuffer pages that have to be flushed
+ * @pagereflist: list of mmap framebuffer pages that have to be flushed
  *
  * This function is used as the &fb_deferred_io.deferred_io
  * callback function for flushing the fbdev mmap writes.
  */
-void drm_fb_helper_deferred_io(struct fb_info *info,
-			       struct list_head *pagelist)
+void drm_fb_helper_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	unsigned long start, end, min, max;
-	struct page *page;
+	struct fb_deferred_io_pageref *pageref;
 	u32 y1, y2;
 
 	min = ULONG_MAX;
 	max = 0;
-	list_for_each_entry(page, pagelist, lru) {
-		start = page->index << PAGE_SHIFT;
+	list_for_each_entry(pageref, pagereflist, list) {
+		start = pageref->offset;
 		end = start + PAGE_SIZE - 1;
 		min = min(min, start);
 		max = max(max, end);
@@ -1327,6 +1326,9 @@
 		return -EINVAL;
 	}
 
+	var->xres_virtual = fb->width;
+	var->yres_virtual = fb->height;
+
 	/*
 	 * Workaround for SDL 1.2, which is known to be setting all pixel format
 	 * fields values to zero in some cases. We treat this situation as a
@@ -1405,14 +1407,14 @@
 }
 EXPORT_SYMBOL(drm_fb_helper_set_par);
 
-static void pan_set(struct drm_fb_helper *fb_helper, int x, int y)
+static void pan_set(struct drm_fb_helper *fb_helper, int dx, int dy)
 {
 	struct drm_mode_set *mode_set;
 
 	mutex_lock(&fb_helper->client.modeset_mutex);
 	drm_client_for_each_modeset(mode_set, &fb_helper->client) {
-		mode_set->x = x;
-		mode_set->y = y;
+		mode_set->x += dx;
+		mode_set->y += dy;
 	}
 	mutex_unlock(&fb_helper->client.modeset_mutex);
 }
@@ -1421,16 +1423,18 @@
 			      struct fb_info *info)
 {
 	struct drm_fb_helper *fb_helper = info->par;
-	int ret;
+	int ret, dx, dy;
 
-	pan_set(fb_helper, var->xoffset, var->yoffset);
+	dx = var->xoffset - info->var.xoffset;
+	dy = var->yoffset - info->var.yoffset;
+	pan_set(fb_helper, dx, dy);
 
 	ret = drm_client_modeset_commit_locked(&fb_helper->client);
 	if (!ret) {
 		info->var.xoffset = var->xoffset;
 		info->var.yoffset = var->yoffset;
 	} else
-		pan_set(fb_helper, info->var.xoffset, info->var.yoffset);
+		pan_set(fb_helper, -dx, -dy);
 
 	return ret;
 }
@@ -1743,7 +1747,13 @@
 			       sizes->fb_width, sizes->fb_height);
 
 	info->par = fb_helper;
-	snprintf(info->fix.id, sizeof(info->fix.id), "%s",
+	/*
+	 * The DRM drivers fbdev emulation device name can be confusing if the
+	 * driver name also has a "drm" suffix on it. Leading to names such as
+	 * "simpledrmdrmfb" in /proc/fb. Unfortunately, it's an uAPI and can't
+	 * be changed due user-space tools (e.g: pm-utils) matching against it.
+	 */
+	snprintf(info->fix.id, sizeof(info->fix.id), "%sdrmfb",
 		 fb_helper->dev->driver->name);
 
 }
@@ -2340,6 +2350,7 @@
 	fbi->fbops = &drm_fbdev_fb_ops;
 	fbi->screen_size = fb->height * fb->pitches[0];
 	fbi->fix.smem_len = fbi->screen_size;
+	fbi->flags = FBINFO_DEFAULT;
 
 	drm_fb_helper_fill_info(fbi, fb_helper, sizes);
 
@@ -2347,19 +2358,21 @@
 		fbi->screen_buffer = vzalloc(fbi->screen_size);
 		if (!fbi->screen_buffer)
 			return -ENOMEM;
+		fbi->flags |= FBINFO_VIRTFB | FBINFO_READS_FAST;
 
 		fbi->fbdefio = &drm_fbdev_defio;
-
 		fb_deferred_io_init(fbi);
 	} else {
 		/* buffer is mapped for HW framebuffer */
 		ret = drm_client_buffer_vmap(fb_helper->buffer, &map);
 		if (ret)
 			return ret;
-		if (map.is_iomem)
+		if (map.is_iomem) {
 			fbi->screen_base = map.vaddr_iomem;
-		else
+		} else {
 			fbi->screen_buffer = map.vaddr;
+			fbi->flags |= FBINFO_VIRTFB;
+		}
 
 		/*
 		 * Shamelessly leak the physical address to user-space. As
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_file.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_file.c
@@ -411,7 +411,7 @@
 {
 	struct drm_device *dev;
 	struct drm_minor *minor;
-	int retcode;
+	int retcode = 0;
 	int need_setup = 0;
 
 	minor = drm_minor_acquire(iminor(inode));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_fourcc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_fourcc.c
@@ -29,6 +29,7 @@
 
 #include <drm/drm_device.h>
 #include <drm/drm_fourcc.h>
+#include <drm/drm_print.h>
 
 /**
  * drm_mode_legacy_fb_format - compute drm fourcc code from legacy description
@@ -153,6 +154,10 @@
 		{ .format = DRM_FORMAT_BGRA5551,	.depth = 15, .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 1, .vsub = 1, .has_alpha = true },
 		{ .format = DRM_FORMAT_RGB565,		.depth = 16, .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 1, .vsub = 1 },
 		{ .format = DRM_FORMAT_BGR565,		.depth = 16, .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 1, .vsub = 1 },
+#ifdef __BIG_ENDIAN
+		{ .format = DRM_FORMAT_XRGB1555 | DRM_FORMAT_BIG_ENDIAN, .depth = 15, .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 1, .vsub = 1 },
+		{ .format = DRM_FORMAT_RGB565 | DRM_FORMAT_BIG_ENDIAN, .depth = 16, .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 1, .vsub = 1 },
+#endif
 		{ .format = DRM_FORMAT_RGB888,		.depth = 24, .num_planes = 1, .cpp = { 3, 0, 0 }, .hsub = 1, .vsub = 1 },
 		{ .format = DRM_FORMAT_BGR888,		.depth = 24, .num_planes = 1, .cpp = { 3, 0, 0 }, .hsub = 1, .vsub = 1 },
 		{ .format = DRM_FORMAT_XRGB8888,	.depth = 24, .num_planes = 1, .cpp = { 4, 0, 0 }, .hsub = 1, .vsub = 1 },
@@ -204,6 +209,9 @@
 		{ .format = DRM_FORMAT_NV61,		.depth = 0,  .num_planes = 2, .cpp = { 1, 2, 0 }, .hsub = 2, .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_NV24,		.depth = 0,  .num_planes = 2, .cpp = { 1, 2, 0 }, .hsub = 1, .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_NV42,		.depth = 0,  .num_planes = 2, .cpp = { 1, 2, 0 }, .hsub = 1, .vsub = 1, .is_yuv = true },
+		{ .format = DRM_FORMAT_XV15,		.depth = 0,  .num_planes = 2, .pixels_per_macropixel = { 3, 3, 0 }, .bytes_per_macropixel = { 4, 8, 0 }, .hsub = 2, .vsub = 2, .is_yuv = true},
+		{ .format = DRM_FORMAT_XV20,		.depth = 0,  .num_planes = 2, .pixels_per_macropixel = { 3, 3, 0 }, .bytes_per_macropixel = { 4, 8, 0 }, .hsub = 2, .vsub = 1, .is_yuv = true},
+		{ .format = DRM_FORMAT_X403,		.depth = 0,  .num_planes = 3, .pixels_per_macropixel = { 3, 3, 3 }, .bytes_per_macropixel = { 4, 4, 4 }, .hsub = 1, .vsub = 1, .is_yuv = true},
 		{ .format = DRM_FORMAT_YUYV,		.depth = 0,  .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 2, .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_YVYU,		.depth = 0,  .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 2, .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_UYVY,		.depth = 0,  .num_planes = 1, .cpp = { 2, 0, 0 }, .hsub = 2, .vsub = 1, .is_yuv = true },
@@ -260,12 +268,20 @@
 		  .vsub = 2, .is_yuv = true },
 		{ .format = DRM_FORMAT_Q410,		.depth = 0,
 		  .num_planes = 3, .char_per_block = { 2, 2, 2 },
-		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 0,
-		  .vsub = 0, .is_yuv = true },
+		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 1,
+		  .vsub = 1, .is_yuv = true },
 		{ .format = DRM_FORMAT_Q401,		.depth = 0,
 		  .num_planes = 3, .char_per_block = { 2, 2, 2 },
-		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 0,
-		  .vsub = 0, .is_yuv = true },
+		  .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 1,
+		  .vsub = 1, .is_yuv = true },
+		{ .format = DRM_FORMAT_P030,            .depth = 0,  .num_planes = 2,
+		  .char_per_block = { 4, 8, 0 }, .block_w = { 3, 3, 0 }, .block_h = { 1, 1, 0 },
+		  .hsub = 2, .vsub = 2, .is_yuv = true},
+		{ .format = DRM_FORMAT_AVUY,		.depth = 0,  .num_planes = 1, .cpp = { 4, 0, 0 }, .hsub = 1, .vsub = 1, .has_alpha = true },
+		{ .format = DRM_FORMAT_XVUY8888,	.depth = 0,  .num_planes = 1, .cpp = { 4, 0, 0 }, .hsub = 1, .vsub = 1 },
+		{ .format = DRM_FORMAT_XVUY2101010,	.depth = 0,  .num_planes = 1, .cpp = { 4, 0, 0 }, .hsub = 1, .vsub = 1 },
+		{ .format = DRM_FORMAT_Y8,		.depth = 0,  .num_planes = 1, .cpp = { 1, 0, 0 }, .hsub = 1, .vsub = 1 },
+		{ .format = DRM_FORMAT_Y10,		.depth = 0,  .num_planes = 1, .pixels_per_macropixel =  { 3, 0, 0 }, .bytes_per_macropixel = { 4, 0, 0 }, .hsub = 1, .vsub = 1 },
 	};
 
 	unsigned int i;
@@ -385,3 +401,36 @@
 			    drm_format_info_block_height(info, plane));
 }
 EXPORT_SYMBOL(drm_format_info_min_pitch);
+
+/**
+ * drm_format_plane_width_bytes - bytes of the given width of the plane
+ * @info: DRM format information
+ * @plane: plane index
+ * @width: width to get the number of bytes
+ *
+ * This returns the number of bytes for given @width and @plane.
+ * The @char_per_block or macro pixel information should be valid.
+ *
+ * Returns:
+ * The bytes of @width of @plane. 0 for invalid format info.
+ */
+uint64_t drm_format_plane_width_bytes(const struct drm_format_info *info,
+				 int plane, unsigned int width)
+{
+	if (!info || plane >= info->num_planes)
+		return 0;
+
+	if (info->char_per_block[plane])
+		return drm_format_info_min_pitch(info, plane, width);
+
+	if (WARN_ON(!info->bytes_per_macropixel[plane] ||
+		    !info->pixels_per_macropixel[plane])) {
+		DRM_WARN("Either cpp or macro-pixel info should be valid: %p4cc\n",
+			 &info->format);
+		return 0;
+	}
+
+	return DIV_ROUND_UP(width * info->bytes_per_macropixel[plane],
+			    info->pixels_per_macropixel[plane]);
+}
+EXPORT_SYMBOL(drm_format_plane_width_bytes);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_framebuffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_framebuffer.c
@@ -198,7 +198,8 @@
 	for (i = 0; i < info->num_planes; i++) {
 		unsigned int width = fb_plane_width(r->width, info, i);
 		unsigned int height = fb_plane_height(r->height, info, i);
-		unsigned int block_size = info->char_per_block[i];
+		unsigned int block_size = info->char_per_block[i] ||
+					  info->bytes_per_macropixel[i];
 		u64 min_pitch = drm_format_info_min_pitch(info, i, width);
 
 		if (!block_size && (r->modifier[i] == DRM_FORMAT_MOD_LINEAR)) {
@@ -292,7 +293,8 @@
 	struct drm_framebuffer *fb;
 	int ret;
 
-	if (r->flags & ~(DRM_MODE_FB_INTERLACED | DRM_MODE_FB_MODIFIERS)) {
+	if (r->flags & ~(DRM_MODE_FB_INTERLACED | DRM_MODE_FB_MODIFIERS |
+	    DRM_MODE_FB_ALTERNATE_TOP | DRM_MODE_FB_ALTERNATE_BOTTOM)) {
 		DRM_DEBUG_KMS("bad framebuffer flags 0x%08x\n", r->flags);
 		return ERR_PTR(-EINVAL);
 	}
@@ -570,7 +572,7 @@
 	struct drm_mode_fb_cmd2 *r = data;
 	struct drm_framebuffer *fb;
 	unsigned int i;
-	int ret;
+	int ret = 0;
 
 	if (!drm_core_check_feature(dev, DRIVER_MODESET))
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_gem.c
@@ -167,21 +167,6 @@
 }
 EXPORT_SYMBOL(drm_gem_private_object_init);
 
-static void
-drm_gem_remove_prime_handles(struct drm_gem_object *obj, struct drm_file *filp)
-{
-	/*
-	 * Note: obj->dma_buf can't disappear as long as we still hold a
-	 * handle reference in obj->handle_count.
-	 */
-	mutex_lock(&filp->prime.lock);
-	if (obj->dma_buf) {
-		drm_prime_remove_buf_handle_locked(&filp->prime,
-						   obj->dma_buf);
-	}
-	mutex_unlock(&filp->prime.lock);
-}
-
 /**
  * drm_gem_object_handle_free - release resources bound to userspace handles
  * @obj: GEM object to clean up.
@@ -252,7 +237,7 @@
 	if (obj->funcs->close)
 		obj->funcs->close(obj, file_priv);
 
-	drm_gem_remove_prime_handles(obj, file_priv);
+	drm_prime_remove_buf_handle(&file_priv->prime, id);
 	drm_vma_node_revoke(&obj->vma_node, file_priv);
 
 	drm_gem_object_handle_put_unlocked(obj);
@@ -1224,7 +1209,7 @@
 		ret = dma_resv_lock_slow_interruptible(obj->resv,
 								 acquire_ctx);
 		if (ret) {
-			ww_acquire_done(acquire_ctx);
+			ww_acquire_fini(acquire_ctx);
 			return ret;
 		}
 	}
@@ -1249,7 +1234,7 @@
 				goto retry;
 			}
 
-			ww_acquire_done(acquire_ctx);
+			ww_acquire_fini(acquire_ctx);
 			return ret;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_gem_cma_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_gem_cma_helper.c
@@ -210,8 +210,13 @@
 			dma_buf_vunmap(gem_obj->import_attach->dmabuf, &map);
 		drm_prime_gem_destroy(gem_obj, cma_obj->sgt);
 	} else if (cma_obj->vaddr) {
-		dma_free_wc(gem_obj->dev->dev, cma_obj->base.size,
-			    cma_obj->vaddr, cma_obj->paddr);
+		if (cma_obj->map_noncoherent)
+			dma_free_noncoherent(gem_obj->dev->dev, cma_obj->base.size,
+					     cma_obj->vaddr, cma_obj->paddr,
+					     DMA_TO_DEVICE);
+		else
+			dma_free_wc(gem_obj->dev->dev, cma_obj->base.size,
+				    cma_obj->vaddr, cma_obj->paddr);
 	}
 
 	drm_gem_object_release(gem_obj);
@@ -510,6 +515,7 @@
 	 */
 	vma->vm_pgoff -= drm_vma_node_start(&obj->vma_node);
 	vma->vm_flags &= ~VM_PFNMAP;
+	vma->vm_flags |= VM_DONTEXPAND;
 
 	cma_obj = to_drm_gem_cma_obj(obj);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_gem_shmem_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_gem_shmem_helper.c
@@ -22,17 +22,22 @@
  *
  * This library provides helpers for GEM objects backed by shmem buffers
  * allocated using anonymous pageable memory.
+ *
+ * Functions that operate on the GEM object receive struct &drm_gem_shmem_object.
+ * For GEM callback helpers in struct &drm_gem_object functions, see likewise
+ * named functions with an _object_ infix (e.g., drm_gem_shmem_object_vmap() wraps
+ * drm_gem_shmem_vmap()). These helpers perform the necessary type conversion.
  */
 
 static const struct drm_gem_object_funcs drm_gem_shmem_funcs = {
-	.free = drm_gem_shmem_free_object,
-	.print_info = drm_gem_shmem_print_info,
-	.pin = drm_gem_shmem_pin,
-	.unpin = drm_gem_shmem_unpin,
-	.get_sg_table = drm_gem_shmem_get_sg_table,
-	.vmap = drm_gem_shmem_vmap,
-	.vunmap = drm_gem_shmem_vunmap,
-	.mmap = drm_gem_shmem_mmap,
+	.free = drm_gem_shmem_object_free,
+	.print_info = drm_gem_shmem_object_print_info,
+	.pin = drm_gem_shmem_object_pin,
+	.unpin = drm_gem_shmem_object_unpin,
+	.get_sg_table = drm_gem_shmem_object_get_sg_table,
+	.vmap = drm_gem_shmem_object_vmap,
+	.vunmap = drm_gem_shmem_object_vunmap,
+	.mmap = drm_gem_shmem_object_mmap,
 };
 
 static struct drm_gem_shmem_object *
@@ -112,16 +117,15 @@
 EXPORT_SYMBOL_GPL(drm_gem_shmem_create);
 
 /**
- * drm_gem_shmem_free_object - Free resources associated with a shmem GEM object
- * @obj: GEM object to free
+ * drm_gem_shmem_free - Free resources associated with a shmem GEM object
+ * @shmem: shmem GEM object to free
  *
  * This function cleans up the GEM object state and frees the memory used to
- * store the object itself. It should be used to implement
- * &drm_gem_object_funcs.free.
+ * store the object itself.
  */
-void drm_gem_shmem_free_object(struct drm_gem_object *obj)
+void drm_gem_shmem_free(struct drm_gem_shmem_object *shmem)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+	struct drm_gem_object *obj = &shmem->base;
 
 	WARN_ON(shmem->vmap_use_count);
 
@@ -145,7 +149,7 @@
 	mutex_destroy(&shmem->vmap_lock);
 	kfree(shmem);
 }
-EXPORT_SYMBOL_GPL(drm_gem_shmem_free_object);
+EXPORT_SYMBOL_GPL(drm_gem_shmem_free);
 
 static int drm_gem_shmem_get_pages_locked(struct drm_gem_shmem_object *shmem)
 {
@@ -225,19 +229,16 @@
 
 /**
  * drm_gem_shmem_pin - Pin backing pages for a shmem GEM object
- * @obj: GEM object
+ * @shmem: shmem GEM object
  *
  * This function makes sure the backing pages are pinned in memory while the
- * buffer is exported. It should only be used to implement
- * &drm_gem_object_funcs.pin.
+ * buffer is exported.
  *
  * Returns:
  * 0 on success or a negative error code on failure.
  */
-int drm_gem_shmem_pin(struct drm_gem_object *obj)
+int drm_gem_shmem_pin(struct drm_gem_shmem_object *shmem)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-
 	WARN_ON(shmem->base.import_attach);
 
 	return drm_gem_shmem_get_pages(shmem);
@@ -246,15 +247,13 @@
 
 /**
  * drm_gem_shmem_unpin - Unpin backing pages for a shmem GEM object
- * @obj: GEM object
+ * @shmem: shmem GEM object
  *
  * This function removes the requirement that the backing pages are pinned in
- * memory. It should only be used to implement &drm_gem_object_funcs.unpin.
+ * memory.
  */
-void drm_gem_shmem_unpin(struct drm_gem_object *obj)
+void drm_gem_shmem_unpin(struct drm_gem_shmem_object *shmem)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-
 	WARN_ON(shmem->base.import_attach);
 
 	drm_gem_shmem_put_pages(shmem);
@@ -275,6 +274,7 @@
 		ret = dma_buf_vmap(obj->import_attach->dmabuf, map);
 		if (!ret) {
 			if (WARN_ON(map->is_iomem)) {
+				dma_buf_vunmap(obj->import_attach->dmabuf, map);
 				ret = -EIO;
 				goto err_put_pages;
 			}
@@ -320,20 +320,16 @@
  *       store.
  *
  * This function makes sure that a contiguous kernel virtual address mapping
- * exists for the buffer backing the shmem GEM object.
- *
- * This function can be used to implement &drm_gem_object_funcs.vmap. But it can
- * also be called by drivers directly, in which case it will hide the
- * differences between dma-buf imported and natively allocated objects.
+ * exists for the buffer backing the shmem GEM object. It hides the differences
+ * between dma-buf imported and natively allocated objects.
  *
  * Acquired mappings should be cleaned up by calling drm_gem_shmem_vunmap().
  *
  * Returns:
  * 0 on success or a negative error code on failure.
  */
-int drm_gem_shmem_vmap(struct drm_gem_object *obj, struct dma_buf_map *map)
+int drm_gem_shmem_vmap(struct drm_gem_shmem_object *shmem, struct dma_buf_map *map)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
 	int ret;
 
 	ret = mutex_lock_interruptible(&shmem->vmap_lock);
@@ -376,21 +372,18 @@
  * drm_gem_shmem_vmap(). The mapping is only removed when the use count drops to
  * zero.
  *
- * This function can be used to implement &drm_gem_object_funcs.vmap. But it can
- * also be called by drivers directly, in which case it will hide the
- * differences between dma-buf imported and natively allocated objects.
+ * This function hides the differences between dma-buf imported and natively
+ * allocated objects.
  */
-void drm_gem_shmem_vunmap(struct drm_gem_object *obj, struct dma_buf_map *map)
+void drm_gem_shmem_vunmap(struct drm_gem_shmem_object *shmem, struct dma_buf_map *map)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-
 	mutex_lock(&shmem->vmap_lock);
 	drm_gem_shmem_vunmap_locked(shmem, map);
 	mutex_unlock(&shmem->vmap_lock);
 }
 EXPORT_SYMBOL(drm_gem_shmem_vunmap);
 
-struct drm_gem_shmem_object *
+static struct drm_gem_shmem_object *
 drm_gem_shmem_create_with_handle(struct drm_file *file_priv,
 				 struct drm_device *dev, size_t size,
 				 uint32_t *handle)
@@ -414,15 +407,12 @@
 
 	return shmem;
 }
-EXPORT_SYMBOL(drm_gem_shmem_create_with_handle);
 
 /* Update madvise status, returns true if not purged, else
  * false or -errno.
  */
-int drm_gem_shmem_madvise(struct drm_gem_object *obj, int madv)
+int drm_gem_shmem_madvise(struct drm_gem_shmem_object *shmem, int madv)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-
 	mutex_lock(&shmem->pages_lock);
 
 	if (shmem->madv >= 0)
@@ -436,14 +426,14 @@
 }
 EXPORT_SYMBOL(drm_gem_shmem_madvise);
 
-void drm_gem_shmem_purge_locked(struct drm_gem_object *obj)
+void drm_gem_shmem_purge_locked(struct drm_gem_shmem_object *shmem)
 {
+	struct drm_gem_object *obj = &shmem->base;
 	struct drm_device *dev = obj->dev;
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
 
 	WARN_ON(!drm_gem_shmem_is_purgeable(shmem));
 
-	dma_unmap_sgtable(obj->dev->dev, shmem->sgt, DMA_BIDIRECTIONAL, 0);
+	dma_unmap_sgtable(dev->dev, shmem->sgt, DMA_BIDIRECTIONAL, 0);
 	sg_free_table(shmem->sgt);
 	kfree(shmem->sgt);
 	shmem->sgt = NULL;
@@ -462,18 +452,15 @@
 	 */
 	shmem_truncate_range(file_inode(obj->filp), 0, (loff_t)-1);
 
-	invalidate_mapping_pages(file_inode(obj->filp)->i_mapping,
-			0, (loff_t)-1);
+	invalidate_mapping_pages(file_inode(obj->filp)->i_mapping, 0, (loff_t)-1);
 }
 EXPORT_SYMBOL(drm_gem_shmem_purge_locked);
 
-bool drm_gem_shmem_purge(struct drm_gem_object *obj)
+bool drm_gem_shmem_purge(struct drm_gem_shmem_object *shmem)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-
 	if (!mutex_trylock(&shmem->pages_lock))
 		return false;
-	drm_gem_shmem_purge_locked(obj);
+	drm_gem_shmem_purge_locked(shmem);
 	mutex_unlock(&shmem->pages_lock);
 
 	return true;
@@ -554,12 +541,20 @@
 {
 	struct drm_gem_object *obj = vma->vm_private_data;
 	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-	int ret;
 
 	WARN_ON(shmem->base.import_attach);
 
-	ret = drm_gem_shmem_get_pages(shmem);
-	WARN_ON_ONCE(ret != 0);
+	mutex_lock(&shmem->pages_lock);
+
+	/*
+	 * We should have already pinned the pages when the buffer was first
+	 * mmap'd, vm_open() just grabs an additional reference for the new
+	 * mm the vma is getting copied into (ie. on fork()).
+	 */
+	if (!WARN_ON_ONCE(!shmem->pages_use_count))
+		shmem->pages_use_count++;
+
+	mutex_unlock(&shmem->pages_lock);
 
 	drm_gem_vm_open(vma);
 }
@@ -581,36 +576,43 @@
 
 /**
  * drm_gem_shmem_mmap - Memory-map a shmem GEM object
- * @obj: gem object
+ * @shmem: shmem GEM object
  * @vma: VMA for the area to be mapped
  *
  * This function implements an augmented version of the GEM DRM file mmap
- * operation for shmem objects. Drivers which employ the shmem helpers should
- * use this function as their &drm_gem_object_funcs.mmap handler.
+ * operation for shmem objects.
  *
  * Returns:
  * 0 on success or a negative error code on failure.
  */
-int drm_gem_shmem_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
+int drm_gem_shmem_mmap(struct drm_gem_shmem_object *shmem, struct vm_area_struct *vma)
 {
-	struct drm_gem_shmem_object *shmem;
+	struct drm_gem_object *obj = &shmem->base;
 	int ret;
 
 	if (obj->import_attach) {
-		/* Drop the reference drm_gem_mmap_obj() acquired.*/
-		drm_gem_object_put(obj);
+		/* Reset both vm_ops and vm_private_data, so we don't end up with
+		 * vm_ops pointing to our implementation if the dma-buf backend
+		 * doesn't set those fields.
+		 */
 		vma->vm_private_data = NULL;
+		vma->vm_ops = NULL;
+
+		ret = dma_buf_mmap(obj->dma_buf, vma, 0);
+
+		/* Drop the reference drm_gem_mmap_obj() acquired.*/
+		if (!ret)
+			drm_gem_object_put(obj);
 
-		return dma_buf_mmap(obj->dma_buf, vma, 0);
+		return ret;
 	}
 
-	shmem = to_drm_gem_shmem_obj(obj);
+	if (is_cow_mapping(vma->vm_flags))
+		return -EINVAL;
 
 	ret = drm_gem_shmem_get_pages(shmem);
-	if (ret) {
-		drm_gem_vm_close(vma);
+	if (ret)
 		return ret;
-	}
 
 	vma->vm_flags |= VM_MIXEDMAP | VM_DONTEXPAND;
 	vma->vm_page_prot = vm_get_page_prot(vma->vm_flags);
@@ -624,17 +626,13 @@
 
 /**
  * drm_gem_shmem_print_info() - Print &drm_gem_shmem_object info for debugfs
+ * @shmem: shmem GEM object
  * @p: DRM printer
  * @indent: Tab indentation level
- * @obj: GEM object
- *
- * This implements the &drm_gem_object_funcs.info callback.
  */
-void drm_gem_shmem_print_info(struct drm_printer *p, unsigned int indent,
-			      const struct drm_gem_object *obj)
+void drm_gem_shmem_print_info(const struct drm_gem_shmem_object *shmem,
+			      struct drm_printer *p, unsigned int indent)
 {
-	const struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
-
 	drm_printf_indent(p, indent, "pages_use_count=%u\n", shmem->pages_use_count);
 	drm_printf_indent(p, indent, "vmap_use_count=%u\n", shmem->vmap_use_count);
 	drm_printf_indent(p, indent, "vaddr=%p\n", shmem->vaddr);
@@ -644,12 +642,10 @@
 /**
  * drm_gem_shmem_get_sg_table - Provide a scatter/gather table of pinned
  *                              pages for a shmem GEM object
- * @obj: GEM object
+ * @shmem: shmem GEM object
  *
  * This function exports a scatter/gather table suitable for PRIME usage by
- * calling the standard DMA mapping API. Drivers should not call this function
- * directly, instead it should only be used as an implementation for
- * &drm_gem_object_funcs.get_sg_table.
+ * calling the standard DMA mapping API.
  *
  * Drivers who need to acquire an scatter/gather table for objects need to call
  * drm_gem_shmem_get_pages_sgt() instead.
@@ -657,9 +653,9 @@
  * Returns:
  * A pointer to the scatter/gather table of pinned pages or NULL on failure.
  */
-struct sg_table *drm_gem_shmem_get_sg_table(struct drm_gem_object *obj)
+struct sg_table *drm_gem_shmem_get_sg_table(struct drm_gem_shmem_object *shmem)
 {
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+	struct drm_gem_object *obj = &shmem->base;
 
 	WARN_ON(shmem->base.import_attach);
 
@@ -667,26 +663,10 @@
 }
 EXPORT_SYMBOL_GPL(drm_gem_shmem_get_sg_table);
 
-/**
- * drm_gem_shmem_get_pages_sgt - Pin pages, dma map them, and return a
- *				 scatter/gather table for a shmem GEM object.
- * @obj: GEM object
- *
- * This function returns a scatter/gather table suitable for driver usage. If
- * the sg table doesn't exist, the pages are pinned, dma-mapped, and a sg
- * table created.
- *
- * This is the main function for drivers to get at backing storage, and it hides
- * and difference between dma-buf imported and natively allocated objects.
- * drm_gem_shmem_get_sg_table() should not be directly called by drivers.
- *
- * Returns:
- * A pointer to the scatter/gather table of pinned pages or errno on failure.
- */
-struct sg_table *drm_gem_shmem_get_pages_sgt(struct drm_gem_object *obj)
+static struct sg_table *drm_gem_shmem_get_pages_sgt_locked(struct drm_gem_shmem_object *shmem)
 {
+	struct drm_gem_object *obj = &shmem->base;
 	int ret;
-	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
 	struct sg_table *sgt;
 
 	if (shmem->sgt)
@@ -694,11 +674,11 @@
 
 	WARN_ON(obj->import_attach);
 
-	ret = drm_gem_shmem_get_pages(shmem);
+	ret = drm_gem_shmem_get_pages_locked(shmem);
 	if (ret)
 		return ERR_PTR(ret);
 
-	sgt = drm_gem_shmem_get_sg_table(&shmem->base);
+	sgt = drm_gem_shmem_get_sg_table(shmem);
 	if (IS_ERR(sgt)) {
 		ret = PTR_ERR(sgt);
 		goto err_put_pages;
@@ -716,9 +696,39 @@
 	sg_free_table(sgt);
 	kfree(sgt);
 err_put_pages:
-	drm_gem_shmem_put_pages(shmem);
+	drm_gem_shmem_put_pages_locked(shmem);
 	return ERR_PTR(ret);
 }
+
+/**
+ * drm_gem_shmem_get_pages_sgt - Pin pages, dma map them, and return a
+ *				 scatter/gather table for a shmem GEM object.
+ * @shmem: shmem GEM object
+ *
+ * This function returns a scatter/gather table suitable for driver usage. If
+ * the sg table doesn't exist, the pages are pinned, dma-mapped, and a sg
+ * table created.
+ *
+ * This is the main function for drivers to get at backing storage, and it hides
+ * and difference between dma-buf imported and natively allocated objects.
+ * drm_gem_shmem_get_sg_table() should not be directly called by drivers.
+ *
+ * Returns:
+ * A pointer to the scatter/gather table of pinned pages or errno on failure.
+ */
+struct sg_table *drm_gem_shmem_get_pages_sgt(struct drm_gem_shmem_object *shmem)
+{
+	int ret;
+	struct sg_table *sgt;
+
+	ret = mutex_lock_interruptible(&shmem->pages_lock);
+	if (ret)
+		return ERR_PTR(ret);
+	sgt = drm_gem_shmem_get_pages_sgt_locked(shmem);
+	mutex_unlock(&shmem->pages_lock);
+
+	return sgt;
+}
 EXPORT_SYMBOL_GPL(drm_gem_shmem_get_pages_sgt);
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_gem_ttm_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_gem_ttm_helper.c
@@ -64,8 +64,13 @@
 		     struct dma_buf_map *map)
 {
 	struct ttm_buffer_object *bo = drm_gem_ttm_of_gem(gem);
+	int ret;
 
-	return ttm_bo_vmap(bo, map);
+	dma_resv_lock(gem->resv, NULL);
+	ret = ttm_bo_vmap(bo, map);
+	dma_resv_unlock(gem->resv);
+
+	return ret;
 }
 EXPORT_SYMBOL(drm_gem_ttm_vmap);
 
@@ -82,7 +87,9 @@
 {
 	struct ttm_buffer_object *bo = drm_gem_ttm_of_gem(gem);
 
+	dma_resv_lock(gem->resv, NULL);
 	ttm_bo_vunmap(bo, map);
+	dma_resv_unlock(gem->resv);
 }
 EXPORT_SYMBOL(drm_gem_ttm_vunmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_gem_vram_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_gem_vram_helper.c
@@ -43,7 +43,7 @@
  * the frame's scanout buffer or the cursor image. If there's no more space
  * left in VRAM, inactive GEM objects can be moved to system memory.
  *
- * To initialize the VRAM helper library call drmm_vram_helper_alloc_mm().
+ * To initialize the VRAM helper library call drmm_vram_helper_init().
  * The function allocates and initializes an instance of &struct drm_vram_mm
  * in &struct drm_device.vram_mm . Use &DRM_GEM_VRAM_DRIVER to initialize
  * &struct drm_driver and  &DRM_VRAM_MM_FILE_OPERATIONS to initialize
@@ -71,7 +71,7 @@
  *		// setup device, vram base and size
  *		// ...
  *
- *		ret = drmm_vram_helper_alloc_mm(dev, vram_base, vram_size);
+ *		ret = drmm_vram_helper_init(dev, vram_base, vram_size);
  *		if (ret)
  *			return ret;
  *		return 0;
@@ -84,7 +84,7 @@
  * to userspace.
  *
  * You don't have to clean up the instance of VRAM MM.
- * drmm_vram_helper_alloc_mm() is a managed interface that installs a
+ * drmm_vram_helper_init() is a managed interface that installs a
  * clean-up handler to run during the DRM device's release.
  *
  * For drawing or scanout operations, rsp. buffer objects have to be pinned
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_internal.h
@@ -74,8 +74,8 @@
 
 void drm_prime_init_file_private(struct drm_prime_file_private *prime_fpriv);
 void drm_prime_destroy_file_private(struct drm_prime_file_private *prime_fpriv);
-void drm_prime_remove_buf_handle_locked(struct drm_prime_file_private *prime_fpriv,
-					struct dma_buf *dma_buf);
+void drm_prime_remove_buf_handle(struct drm_prime_file_private *prime_fpriv,
+				 uint32_t handle);
 
 /* drm_drv.c */
 struct drm_minor *drm_minor_acquire(unsigned int minor_id);
@@ -104,7 +104,8 @@
 
 static inline void drm_vblank_destroy_worker(struct drm_vblank_crtc *vblank)
 {
-	kthread_destroy_worker(vblank->worker);
+	if (vblank->worker)
+		kthread_destroy_worker(vblank->worker);
 }
 
 int drm_vblank_worker_init(struct drm_vblank_crtc *vblank);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_ioctl.c
@@ -472,7 +472,13 @@
  */
 static int drm_copy_field(char __user *buf, size_t *buf_len, const char *value)
 {
-	int len;
+	size_t len;
+
+	/* don't attempt to copy a NULL pointer */
+	if (WARN_ONCE(!value, "BUG: the value to copy was not set!")) {
+		*buf_len = 0;
+		return 0;
+	}
 
 	/* don't overflow userbuf */
 	len = strlen(value);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_mipi_dbi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_mipi_dbi.c
@@ -1183,6 +1183,13 @@
 	size_t chunk;
 	int ret;
 
+	/* In __spi_validate, there's a validation that no partial transfers
+	 * are accepted (xfer->len % w_size must be zero).
+	 * Here we align max_chunk to multiple of 2 (16bits),
+	 * to prevent transfers from being rejected.
+	 */
+	max_chunk = ALIGN_DOWN(max_chunk, 2);
+
 	spi_message_init_with_transfers(&m, &tr, 1);
 
 	while (len) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_mipi_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_mipi_dsi.c
@@ -246,6 +246,52 @@
 }
 EXPORT_SYMBOL(mipi_dsi_device_unregister);
 
+static void devm_mipi_dsi_device_unregister(void *arg)
+{
+	struct mipi_dsi_device *dsi = arg;
+
+	mipi_dsi_device_unregister(dsi);
+}
+
+/**
+ * devm_mipi_dsi_device_register_full - create a managed MIPI DSI device
+ * @dev: device to tie the MIPI-DSI device lifetime to
+ * @host: DSI host to which this device is connected
+ * @info: pointer to template containing DSI device information
+ *
+ * Create a MIPI DSI device by using the device information provided by
+ * mipi_dsi_device_info template
+ *
+ * This is the managed version of mipi_dsi_device_register_full() which
+ * automatically calls mipi_dsi_device_unregister() when @dev is
+ * unbound.
+ *
+ * Returns:
+ * A pointer to the newly created MIPI DSI device, or, a pointer encoded
+ * with an error
+ */
+struct mipi_dsi_device *
+devm_mipi_dsi_device_register_full(struct device *dev,
+				   struct mipi_dsi_host *host,
+				   const struct mipi_dsi_device_info *info)
+{
+	struct mipi_dsi_device *dsi;
+	int ret;
+
+	dsi = mipi_dsi_device_register_full(host, info);
+	if (IS_ERR(dsi))
+		return dsi;
+
+	ret = devm_add_action_or_reset(dev,
+				       devm_mipi_dsi_device_unregister,
+				       dsi);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return dsi;
+}
+EXPORT_SYMBOL_GPL(devm_mipi_dsi_device_register_full);
+
 static DEFINE_MUTEX(host_lock);
 static LIST_HEAD(host_list);
 
@@ -300,6 +346,8 @@
 {
 	struct mipi_dsi_device *dsi = to_mipi_dsi_device(dev);
 
+	if (dsi->attached)
+		mipi_dsi_detach(dsi);
 	mipi_dsi_device_unregister(dsi);
 
 	return 0;
@@ -322,11 +370,18 @@
 int mipi_dsi_attach(struct mipi_dsi_device *dsi)
 {
 	const struct mipi_dsi_host_ops *ops = dsi->host->ops;
+	int ret;
 
 	if (!ops || !ops->attach)
 		return -ENOSYS;
 
-	return ops->attach(dsi->host, dsi);
+	ret = ops->attach(dsi->host, dsi);
+	if (ret)
+		return ret;
+
+	dsi->attached = true;
+
+	return 0;
 }
 EXPORT_SYMBOL(mipi_dsi_attach);
 
@@ -338,13 +393,53 @@
 {
 	const struct mipi_dsi_host_ops *ops = dsi->host->ops;
 
+	if (WARN_ON(!dsi->attached))
+		return -EINVAL;
+
 	if (!ops || !ops->detach)
 		return -ENOSYS;
 
+	dsi->attached = false;
+
 	return ops->detach(dsi->host, dsi);
 }
 EXPORT_SYMBOL(mipi_dsi_detach);
 
+static void devm_mipi_dsi_detach(void *arg)
+{
+	struct mipi_dsi_device *dsi = arg;
+
+	mipi_dsi_detach(dsi);
+}
+
+/**
+ * devm_mipi_dsi_attach - Attach a MIPI-DSI device to its DSI Host
+ * @dev: device to tie the MIPI-DSI device attachment lifetime to
+ * @dsi: DSI peripheral
+ *
+ * This is the managed version of mipi_dsi_attach() which automatically
+ * calls mipi_dsi_detach() when @dev is unbound.
+ *
+ * Returns:
+ * 0 on success, a negative error code on failure.
+ */
+int devm_mipi_dsi_attach(struct device *dev,
+			 struct mipi_dsi_device *dsi)
+{
+	int ret;
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(dev, devm_mipi_dsi_detach, dsi);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(devm_mipi_dsi_attach);
+
 static ssize_t mipi_dsi_device_transfer(struct mipi_dsi_device *dsi,
 					struct mipi_dsi_msg *msg)
 {
@@ -558,7 +653,7 @@
  *
  * Return: 0 on success or a negative error code on failure.
  */
-ssize_t mipi_dsi_compression_mode(struct mipi_dsi_device *dsi, bool enable)
+int mipi_dsi_compression_mode(struct mipi_dsi_device *dsi, bool enable)
 {
 	/* Note: Needs updating for non-default PPS or algorithm */
 	u8 tx[2] = { enable << 0, 0 };
@@ -583,8 +678,8 @@
  *
  * Return: 0 on success or a negative error code on failure.
  */
-ssize_t mipi_dsi_picture_parameter_set(struct mipi_dsi_device *dsi,
-				       const struct drm_dsc_picture_parameter_set *pps)
+int mipi_dsi_picture_parameter_set(struct mipi_dsi_device *dsi,
+				   const struct drm_dsc_picture_parameter_set *pps)
 {
 	struct mipi_dsi_msg msg = {
 		.channel = dsi->channel,
@@ -1142,6 +1237,58 @@
 }
 EXPORT_SYMBOL(mipi_dsi_dcs_get_display_brightness);
 
+/**
+ * mipi_dsi_dcs_set_display_brightness_large() - sets the 16-bit brightness value
+ *    of the display
+ * @dsi: DSI peripheral device
+ * @brightness: brightness value
+ *
+ * Return: 0 on success or a negative error code on failure.
+ */
+int mipi_dsi_dcs_set_display_brightness_large(struct mipi_dsi_device *dsi,
+					     u16 brightness)
+{
+	u8 payload[2] = { brightness >> 8, brightness & 0xff };
+	ssize_t err;
+
+	err = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_DISPLAY_BRIGHTNESS,
+				 payload, sizeof(payload));
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+EXPORT_SYMBOL(mipi_dsi_dcs_set_display_brightness_large);
+
+/**
+ * mipi_dsi_dcs_get_display_brightness_large() - gets the current 16-bit
+ *    brightness value of the display
+ * @dsi: DSI peripheral device
+ * @brightness: brightness value
+ *
+ * Return: 0 on success or a negative error code on failure.
+ */
+int mipi_dsi_dcs_get_display_brightness_large(struct mipi_dsi_device *dsi,
+					     u16 *brightness)
+{
+	u8 brightness_be[2];
+	ssize_t err;
+
+	err = mipi_dsi_dcs_read(dsi, MIPI_DCS_GET_DISPLAY_BRIGHTNESS,
+				brightness_be, sizeof(brightness_be));
+	if (err <= 0) {
+		if (err == 0)
+			err = -ENODATA;
+
+		return err;
+	}
+
+	*brightness = (brightness_be[0] << 8) | brightness_be[1];
+
+	return 0;
+}
+EXPORT_SYMBOL(mipi_dsi_dcs_get_display_brightness_large);
+
 static int mipi_dsi_drv_probe(struct device *dev)
 {
 	struct mipi_dsi_driver *drv = to_mipi_dsi_driver(dev->driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_mm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_mm.c
@@ -154,7 +154,7 @@
 
 INTERVAL_TREE_DEFINE(struct drm_mm_node, rb,
 		     u64, __subtree_last,
-		     START, LAST, static inline, drm_mm_interval_tree)
+		     START, LAST, static inline __maybe_unused, drm_mm_interval_tree)
 
 struct drm_mm_node *
 __drm_mm_interval_first(const struct drm_mm *mm, u64 start, u64 last)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_mode_config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_mode_config.c
@@ -398,6 +398,8 @@
  */
 int drmm_mode_config_init(struct drm_device *dev)
 {
+	int ret;
+
 	mutex_init(&dev->mode_config.mutex);
 	drm_modeset_lock_init(&dev->mode_config.connection_mutex);
 	mutex_init(&dev->mode_config.idr_mutex);
@@ -419,7 +421,11 @@
 	init_llist_head(&dev->mode_config.connector_free_list);
 	INIT_WORK(&dev->mode_config.connector_free_work, drm_connector_free_work_fn);
 
-	drm_mode_create_standard_properties(dev);
+	ret = drm_mode_create_standard_properties(dev);
+	if (ret) {
+		drm_mode_config_cleanup(dev);
+		return ret;
+	}
 
 	/* Just to be sure */
 	dev->mode_config.num_fb = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_modes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_modes.c
@@ -757,14 +757,11 @@
  */
 int drm_mode_vrefresh(const struct drm_display_mode *mode)
 {
-	unsigned int num, den;
+	unsigned int num = 1, den = 1;
 
 	if (mode->htotal == 0 || mode->vtotal == 0)
 		return 0;
 
-	num = mode->clock;
-	den = mode->htotal * mode->vtotal;
-
 	if (mode->flags & DRM_MODE_FLAG_INTERLACE)
 		num *= 2;
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
@@ -772,6 +769,12 @@
 	if (mode->vscan > 1)
 		den *= mode->vscan;
 
+	if (check_mul_overflow(mode->clock, num, &num))
+		return 0;
+
+	if (check_mul_overflow(mode->htotal * mode->vtotal, den, &den))
+		return 0;
+
 	return DIV_ROUND_CLOSEST_ULL(mul_u32_u32(num, 1000), den);
 }
 EXPORT_SYMBOL(drm_mode_vrefresh);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_modeset_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_modeset_helper.c
@@ -198,13 +198,22 @@
 
 	if (!dev)
 		return 0;
+	/*
+	 * Don't disable polling if it was never initialized
+	 */
+	if (dev->mode_config.poll_enabled)
+		drm_kms_helper_poll_disable(dev);
 
-	drm_kms_helper_poll_disable(dev);
 	drm_fb_helper_set_suspend_unlocked(dev->fb_helper, 1);
 	state = drm_atomic_helper_suspend(dev);
 	if (IS_ERR(state)) {
 		drm_fb_helper_set_suspend_unlocked(dev->fb_helper, 0);
-		drm_kms_helper_poll_enable(dev);
+		/*
+		 * Don't enable polling if it was never initialized
+		 */
+		if (dev->mode_config.poll_enabled)
+			drm_kms_helper_poll_enable(dev);
+
 		return PTR_ERR(state);
 	}
 
@@ -244,7 +253,11 @@
 	dev->mode_config.suspend_state = NULL;
 
 	drm_fb_helper_set_suspend_unlocked(dev->fb_helper, 0);
-	drm_kms_helper_poll_enable(dev);
+	/*
+	 * Don't enable polling if it is not initialized
+	 */
+	if (dev->mode_config.poll_enabled)
+		drm_kms_helper_poll_enable(dev);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_of.c
@@ -231,6 +231,9 @@
  * return either the associated struct drm_panel or drm_bridge device. Either
  * @panel or @bridge must not be NULL.
  *
+ * This function is deprecated and should not be used in new drivers. Use
+ * devm_drm_of_get_bridge() instead.
+ *
  * Returns zero if successful, or one of the standard error codes if it fails.
  */
 int drm_of_find_panel_or_bridge(const struct device_node *np,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_panel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_panel.c
@@ -207,19 +207,24 @@
  * The modes probed from the panel are automatically added to the connector
  * that the panel is attached to.
  *
- * Return: The number of modes available from the panel on success or a
- * negative error code on failure.
+ * Return: The number of modes available from the panel on success, or 0 on
+ * failure (no modes).
  */
 int drm_panel_get_modes(struct drm_panel *panel,
 			struct drm_connector *connector)
 {
 	if (!panel)
-		return -EINVAL;
+		return 0;
 
-	if (panel->funcs && panel->funcs->get_modes)
-		return panel->funcs->get_modes(panel, connector);
+	if (panel->funcs && panel->funcs->get_modes) {
+		int num;
 
-	return -EOPNOTSUPP;
+		num = panel->funcs->get_modes(panel, connector);
+		if (num > 0)
+			return num;
+	}
+
+	return 0;
 }
 EXPORT_SYMBOL(drm_panel_get_modes);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_panel_orientation_quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_panel_orientation_quirks.c
@@ -44,6 +44,14 @@
 	.orientation = DRM_MODE_PANEL_ORIENTATION_RIGHT_UP,
 };
 
+static const struct drm_dmi_panel_orientation_data gpd_onemix2s = {
+	.width = 1200,
+	.height = 1920,
+	.bios_dates = (const char * const []){ "05/21/2018", "10/26/2018",
+		"03/04/2019", NULL },
+	.orientation = DRM_MODE_PANEL_ORIENTATION_RIGHT_UP,
+};
+
 static const struct drm_dmi_panel_orientation_data gpd_pocket = {
 	.width = 1200,
 	.height = 1920,
@@ -109,6 +117,18 @@
 	.orientation = DRM_MODE_PANEL_ORIENTATION_RIGHT_UP,
 };
 
+static const struct drm_dmi_panel_orientation_data lcd1280x1920_rightside_up = {
+	.width = 1280,
+	.height = 1920,
+	.orientation = DRM_MODE_PANEL_ORIENTATION_RIGHT_UP,
+};
+
+static const struct drm_dmi_panel_orientation_data lcd1600x2560_leftside_up = {
+	.width = 1600,
+	.height = 2560,
+	.orientation = DRM_MODE_PANEL_ORIENTATION_LEFT_UP,
+};
+
 static const struct dmi_system_id orientation_data[] = {
 	{	/* Acer One 10 (S1003) */
 		.matches = {
@@ -116,6 +136,18 @@
 		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "One S1003"),
 		},
 		.driver_data = (void *)&lcd800x1280_rightside_up,
+	}, {	/* Acer Switch V 10 (SW5-017) */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "SW5-017"),
+		},
+		.driver_data = (void *)&lcd800x1280_rightside_up,
+	}, {	/* Anbernic Win600 */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "Anbernic"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Win600"),
+		},
+		.driver_data = (void *)&lcd720x1280_rightside_up,
 	}, {	/* Asus T100HA */
 		.matches = {
 		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
@@ -134,6 +166,12 @@
 		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "T103HAF"),
 		},
 		.driver_data = (void *)&lcd800x1280_rightside_up,
+	}, {	/* AYA NEO AYANEO 2 */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AYANEO"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "AYANEO 2"),
+		},
+		.driver_data = (void *)&lcd1200x1920_rightside_up,
 	}, {	/* AYA NEO 2021 */
 		.matches = {
 		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AYADEVICE"),
@@ -154,6 +192,12 @@
 		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "MicroPC"),
 		},
 		.driver_data = (void *)&lcd720x1280_rightside_up,
+	}, {	/* GPD Win Max */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "GPD"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "G1619-01"),
+		},
+		.driver_data = (void *)&lcd800x1280_rightside_up,
 	}, {	/*
 		 * GPD Pocket, note that the the DMI data is less generic then
 		 * it seems, devices with a board-vendor of "AMI Corporation"
@@ -205,6 +249,13 @@
 		  DMI_EXACT_MATCH(DMI_BOARD_NAME, "TW891"),
 		},
 		.driver_data = (void *)&itworks_tw891,
+	}, {	/* KD Kurio Smart C15200 2-in-1 */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "KD Interactive"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Kurio Smart"),
+		  DMI_EXACT_MATCH(DMI_BOARD_NAME, "KDM960BCP"),
+		},
+		.driver_data = (void *)&lcd800x1280_rightside_up,
 	}, {	/*
 		 * Lenovo Ideapad Miix 310 laptop, only some production batches
 		 * have a portrait screen, the resolution checks makes the quirk
@@ -223,12 +274,42 @@
 		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "Lenovo MIIX 320-10ICR"),
 		},
 		.driver_data = (void *)&lcd800x1280_rightside_up,
-	}, {	/* Lenovo Ideapad D330 */
+	}, {	/* Lenovo Ideapad D330-10IGM (HD) */
 		.matches = {
 		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "LENOVO"),
-		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "81H3"),
 		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "Lenovo ideapad D330-10IGM"),
 		},
+		.driver_data = (void *)&lcd800x1280_rightside_up,
+	}, {	/* Lenovo Ideapad D330-10IGM (FHD) */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "Lenovo ideapad D330-10IGM"),
+		},
+		.driver_data = (void *)&lcd1200x1920_rightside_up,
+	}, {	/* Lenovo Ideapad D330-10IGL (HD) */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "Lenovo ideapad D330-10IGL"),
+		},
+		.driver_data = (void *)&lcd800x1280_rightside_up,
+	}, {	/* Lenovo IdeaPad Duet 3 10IGL5 */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "IdeaPad Duet 3 10IGL5"),
+		},
+		.driver_data = (void *)&lcd1200x1920_rightside_up,
+	}, {	/* Lenovo Yoga Book X90F / X90L */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Intel Corporation"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "CHERRYVIEW D1 PLATFORM"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "YETI-11"),
+		},
+		.driver_data = (void *)&lcd1200x1920_rightside_up,
+	}, {	/* Lenovo Yoga Book X91F / X91L */
+		.matches = {
+		  /* Non exact match to match F + L versions */
+		  DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X91"),
+		},
 		.driver_data = (void *)&lcd1200x1920_rightside_up,
 	}, {	/* OneGX1 Pro */
 		.matches = {
@@ -237,12 +318,45 @@
 		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "Default string"),
 		},
 		.driver_data = (void *)&onegx1_pro,
+	}, {	/* OneXPlayer */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "ONE-NETBOOK TECHNOLOGY CO., LTD."),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "ONE XPLAYER"),
+		},
+		.driver_data = (void *)&lcd1600x2560_leftside_up,
+	}, {	/* OrangePi Neo */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "OrangePi"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "NEO-01"),
+		},
+		.driver_data = (void *)&lcd1200x1920_rightside_up,
+	}, {	/* Samsung GalaxyBook 10.6 */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "SAMSUNG ELECTRONICS CO., LTD."),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Galaxy Book 10.6"),
+		},
+		.driver_data = (void *)&lcd1280x1920_rightside_up,
+	}, {	/* Valve Steam Deck */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Valve"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Jupiter"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "1"),
+		},
+		.driver_data = (void *)&lcd800x1280_rightside_up,
 	}, {	/* VIOS LTH17 */
 		.matches = {
 		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "VIOS"),
 		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "LTH17"),
 		},
 		.driver_data = (void *)&lcd800x1280_rightside_up,
+	}, {	/* One Mix 2S (generic strings, also match on bios date) */
+		.matches = {
+		  DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Default string"),
+		  DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Default string"),
+		  DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "Default string"),
+		  DMI_EXACT_MATCH(DMI_BOARD_NAME, "Default string"),
+		},
+		.driver_data = (void *)&gpd_onemix2s,
 	},
 	{}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_plane.c
@@ -249,6 +249,13 @@
 	if (WARN_ON(config->num_total_plane >= 32))
 		return -EINVAL;
 
+	/*
+	 * First driver to need more than 64 formats needs to fix this. Each
+	 * format is encoded as a bit and the current code only supports a u64.
+	 */
+	if (WARN_ON(format_count > 64))
+		return -EINVAL;
+
 	WARN_ON(drm_drv_uses_atomic_modeset(dev) &&
 		(!funcs->atomic_destroy_state ||
 		 !funcs->atomic_duplicate_state));
@@ -270,13 +277,6 @@
 		return -ENOMEM;
 	}
 
-	/*
-	 * First driver to need more than 64 formats needs to fix this. Each
-	 * format is encoded as a bit and the current code only supports a u64.
-	 */
-	if (WARN_ON(format_count > 64))
-		return -EINVAL;
-
 	if (format_modifiers) {
 		const uint64_t *temp_modifiers = format_modifiers;
 
@@ -1378,6 +1378,7 @@
 out:
 	if (fb)
 		drm_framebuffer_put(fb);
+	fb = NULL;
 	if (plane->old_fb)
 		drm_framebuffer_put(plane->old_fb);
 	plane->old_fb = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_plane_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_plane_helper.c
@@ -123,7 +123,6 @@
 		.crtc_w = drm_rect_width(dst),
 		.crtc_h = drm_rect_height(dst),
 		.rotation = rotation,
-		.visible = *visible,
 	};
 	struct drm_crtc_state crtc_state = {
 		.crtc = crtc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_prime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_prime.c
@@ -187,29 +187,33 @@
 	return -ENOENT;
 }
 
-void drm_prime_remove_buf_handle_locked(struct drm_prime_file_private *prime_fpriv,
-					struct dma_buf *dma_buf)
+void drm_prime_remove_buf_handle(struct drm_prime_file_private *prime_fpriv,
+				 uint32_t handle)
 {
 	struct rb_node *rb;
 
-	rb = prime_fpriv->dmabufs.rb_node;
+	mutex_lock(&prime_fpriv->lock);
+
+	rb = prime_fpriv->handles.rb_node;
 	while (rb) {
 		struct drm_prime_member *member;
 
-		member = rb_entry(rb, struct drm_prime_member, dmabuf_rb);
-		if (member->dma_buf == dma_buf) {
+		member = rb_entry(rb, struct drm_prime_member, handle_rb);
+		if (member->handle == handle) {
 			rb_erase(&member->handle_rb, &prime_fpriv->handles);
 			rb_erase(&member->dmabuf_rb, &prime_fpriv->dmabufs);
 
-			dma_buf_put(dma_buf);
+			dma_buf_put(member->dma_buf);
 			kfree(member);
-			return;
-		} else if (member->dma_buf < dma_buf) {
+			break;
+		} else if (member->handle < handle) {
 			rb = rb->rb_right;
 		} else {
 			rb = rb->rb_left;
 		}
 	}
+
+	mutex_unlock(&prime_fpriv->lock);
 }
 
 void drm_prime_init_file_private(struct drm_prime_file_private *prime_fpriv)
@@ -719,11 +723,13 @@
 	if (obj->funcs && obj->funcs->mmap) {
 		vma->vm_ops = obj->funcs->vm_ops;
 
+		drm_gem_object_get(obj);
 		ret = obj->funcs->mmap(obj, vma);
-		if (ret)
+		if (ret) {
+			drm_gem_object_put(obj);
 			return ret;
+		}
 		vma->vm_private_data = obj;
-		drm_gem_object_get(obj);
 		return 0;
 	}
 
@@ -819,7 +825,7 @@
 	if (max_segment == 0)
 		max_segment = UINT_MAX;
 	err = sg_alloc_table_from_pages_segment(sg, pages, nr_pages, 0,
-						nr_pages << PAGE_SHIFT,
+						(unsigned long)nr_pages << PAGE_SHIFT,
 						max_segment, GFP_KERNEL);
 	if (err) {
 		kfree(sg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_print.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_print.c
@@ -78,8 +78,9 @@
 			copy = iterator->remain;
 
 		/* Copy out the bit of the string that we need */
-		memcpy(iterator->data,
-			str + (iterator->start - iterator->offset), copy);
+		if (iterator->data)
+			memcpy(iterator->data,
+			       str + (iterator->start - iterator->offset), copy);
 
 		iterator->offset = iterator->start + copy;
 		iterator->remain -= copy;
@@ -88,7 +89,8 @@
 
 		len = min_t(ssize_t, strlen(str), iterator->remain);
 
-		memcpy(iterator->data + pos, str, len);
+		if (iterator->data)
+			memcpy(iterator->data + pos, str, len);
 
 		iterator->offset += len;
 		iterator->remain -= len;
@@ -118,8 +120,9 @@
 	if ((iterator->offset >= iterator->start) && (len < iterator->remain)) {
 		ssize_t pos = iterator->offset - iterator->start;
 
-		snprintf(((char *) iterator->data) + pos,
-			iterator->remain, "%pV", vaf);
+		if (iterator->data)
+			snprintf(((char *) iterator->data) + pos,
+				 iterator->remain, "%pV", vaf);
 
 		iterator->offset += len;
 		iterator->remain -= len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_probe_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_probe_helper.c
@@ -235,6 +235,9 @@
  * Drivers can call this helper from their device resume implementation. It is
  * not an error to call this even when output polling isn't enabled.
  *
+ * If device polling was never initialized before, this call will trigger a
+ * warning and return.
+ *
  * Note that calls to enable and disable polling must be strictly ordered, which
  * is automatically the case when they're only call from suspend/resume
  * callbacks.
@@ -246,7 +249,8 @@
 	struct drm_connector_list_iter conn_iter;
 	unsigned long delay = DRM_OUTPUT_POLL_PERIOD;
 
-	if (!dev->mode_config.poll_enabled || !drm_kms_helper_poll)
+	if (drm_WARN_ON_ONCE(dev, !dev->mode_config.poll_enabled) ||
+	    !drm_kms_helper_poll || dev->mode_config.poll_running)
 		return;
 
 	drm_connector_list_iter_begin(dev, &conn_iter);
@@ -488,12 +492,14 @@
 		 */
 		dev->mode_config.delayed_event = true;
 		if (dev->mode_config.poll_enabled)
-			schedule_delayed_work(&dev->mode_config.output_poll_work,
-					      0);
+			mod_delayed_work(system_wq,
+					 &dev->mode_config.output_poll_work,
+					 0);
 	}
 
 	/* Re-enable polling in case the global poll config changed. */
-	if (drm_kms_helper_poll != dev->mode_config.poll_running)
+	if (dev->mode_config.poll_enabled &&
+	    (drm_kms_helper_poll != dev->mode_config.poll_running))
 		drm_kms_helper_poll_enable(dev);
 
 	dev->mode_config.poll_running = drm_kms_helper_poll;
@@ -741,14 +747,18 @@
  * not an error to call this even when output polling isn't enabled or already
  * disabled. Polling is re-enabled by calling drm_kms_helper_poll_enable().
  *
+ * If however, the polling was never initialized, this call will trigger a
+ * warning and return
+ *
  * Note that calls to enable and disable polling must be strictly ordered, which
  * is automatically the case when they're only call from suspend/resume
  * callbacks.
  */
 void drm_kms_helper_poll_disable(struct drm_device *dev)
 {
-	if (!dev->mode_config.poll_enabled)
+	if (drm_WARN_ON(dev, !dev->mode_config.poll_enabled))
 		return;
+
 	cancel_delayed_work_sync(&dev->mode_config.output_poll_work);
 }
 EXPORT_SYMBOL(drm_kms_helper_poll_disable);
@@ -795,6 +805,86 @@
 }
 EXPORT_SYMBOL(drm_kms_helper_poll_fini);
 
+static bool check_connector_changed(struct drm_connector *connector)
+{
+	struct drm_device *dev = connector->dev;
+	enum drm_connector_status old_status;
+	u64 old_epoch_counter;
+
+	/* Only handle HPD capable connectors. */
+	drm_WARN_ON(dev, !(connector->polled & DRM_CONNECTOR_POLL_HPD));
+
+	drm_WARN_ON(dev, !mutex_is_locked(&dev->mode_config.mutex));
+
+	old_status = connector->status;
+	old_epoch_counter = connector->epoch_counter;
+	connector->status = drm_helper_probe_detect(connector, NULL, false);
+
+	if (old_epoch_counter == connector->epoch_counter) {
+		drm_dbg_kms(dev, "[CONNECTOR:%d:%s] Same epoch counter %llu\n",
+			    connector->base.id,
+			    connector->name,
+			    connector->epoch_counter);
+
+		return false;
+	}
+
+	drm_dbg_kms(dev, "[CONNECTOR:%d:%s] status updated from %s to %s\n",
+		    connector->base.id,
+		    connector->name,
+		    drm_get_connector_status_name(old_status),
+		    drm_get_connector_status_name(connector->status));
+
+	drm_dbg_kms(dev, "[CONNECTOR:%d:%s] Changed epoch counter %llu => %llu\n",
+		    connector->base.id,
+		    connector->name,
+		    old_epoch_counter,
+		    connector->epoch_counter);
+
+	return true;
+}
+
+/**
+ * drm_connector_helper_hpd_irq_event - hotplug processing
+ * @connector: drm_connector
+ *
+ * Drivers can use this helper function to run a detect cycle on a connector
+ * which has the DRM_CONNECTOR_POLL_HPD flag set in its &polled member.
+ *
+ * This helper function is useful for drivers which can track hotplug
+ * interrupts for a single connector. Drivers that want to send a
+ * hotplug event for all connectors or can't track hotplug interrupts
+ * per connector need to use drm_helper_hpd_irq_event().
+ *
+ * This function must be called from process context with no mode
+ * setting locks held.
+ *
+ * Note that a connector can be both polled and probed from the hotplug
+ * handler, in case the hotplug interrupt is known to be unreliable.
+ *
+ * Returns:
+ * A boolean indicating whether the connector status changed or not
+ */
+bool drm_connector_helper_hpd_irq_event(struct drm_connector *connector)
+{
+	struct drm_device *dev = connector->dev;
+	bool changed;
+
+	mutex_lock(&dev->mode_config.mutex);
+	changed = check_connector_changed(connector);
+	mutex_unlock(&dev->mode_config.mutex);
+
+	if (changed) {
+		drm_kms_helper_hotplug_event(dev);
+		drm_dbg_kms(dev, "[CONNECTOR:%d:%s] Sent hotplug event\n",
+			    connector->base.id,
+			    connector->name);
+	}
+
+	return changed;
+}
+EXPORT_SYMBOL(drm_connector_helper_hpd_irq_event);
+
 /**
  * drm_helper_hpd_irq_event - hotplug processing
  * @dev: drm_device
@@ -808,9 +898,10 @@
  * interrupts for each connector.
  *
  * Drivers which support hotplug interrupts for each connector individually and
- * which have a more fine-grained detect logic should bypass this code and
- * directly call drm_kms_helper_hotplug_event() in case the connector state
- * changed.
+ * which have a more fine-grained detect logic can use
+ * drm_connector_helper_hpd_irq_event(). Alternatively, they should bypass this
+ * code and directly call drm_kms_helper_hotplug_event() in case the connector
+ * state changed.
  *
  * This function must be called from process context with no mode
  * setting locks held.
@@ -822,9 +913,7 @@
 {
 	struct drm_connector *connector;
 	struct drm_connector_list_iter conn_iter;
-	enum drm_connector_status old_status;
 	bool changed = false;
-	u64 old_epoch_counter;
 
 	if (!dev->mode_config.poll_enabled)
 		return false;
@@ -836,33 +925,8 @@
 		if (!(connector->polled & DRM_CONNECTOR_POLL_HPD))
 			continue;
 
-		old_status = connector->status;
-
-		old_epoch_counter = connector->epoch_counter;
-
-		DRM_DEBUG_KMS("[CONNECTOR:%d:%s] Old epoch counter %llu\n", connector->base.id,
-			      connector->name,
-			      old_epoch_counter);
-
-		connector->status = drm_helper_probe_detect(connector, NULL, false);
-		DRM_DEBUG_KMS("[CONNECTOR:%d:%s] status updated from %s to %s\n",
-			      connector->base.id,
-			      connector->name,
-			      drm_get_connector_status_name(old_status),
-			      drm_get_connector_status_name(connector->status));
-
-		DRM_DEBUG_KMS("[CONNECTOR:%d:%s] New epoch counter %llu\n",
-			      connector->base.id,
-			      connector->name,
-			      connector->epoch_counter);
-
-		/*
-		 * Check if epoch counter had changed, meaning that we need
-		 * to send a uevent.
-		 */
-		if (old_epoch_counter != connector->epoch_counter)
+		if (check_connector_changed(connector))
 			changed = true;
-
 	}
 	drm_connector_list_iter_end(&conn_iter);
 	mutex_unlock(&dev->mode_config.mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/drm_syncobj.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/drm_syncobj.c
@@ -404,8 +404,17 @@
 
 	if (*fence) {
 		ret = dma_fence_chain_find_seqno(fence, point);
-		if (!ret)
+		if (!ret) {
+			/* If the requested seqno is already signaled
+			 * drm_syncobj_find_fence may return a NULL
+			 * fence. To make sure the recipient gets
+			 * signalled, use a new fence instead.
+			 */
+			if (!*fence)
+				*fence = dma_fence_get_stub();
+
 			goto out;
+		}
 		dma_fence_put(*fence);
 	} else {
 		ret = -EINVAL;
@@ -844,12 +853,57 @@
 					&args->handle);
 }
 
+
+/*
+ * Try to flatten a dma_fence_chain into a dma_fence_array so that it can be
+ * added as timeline fence to a chain again.
+ */
+static int drm_syncobj_flatten_chain(struct dma_fence **f)
+{
+	struct dma_fence_chain *chain = to_dma_fence_chain(*f);
+	struct dma_fence *tmp, **fences;
+	struct dma_fence_array *array;
+	unsigned int count;
+
+	if (!chain)
+		return 0;
+
+	count = 0;
+	dma_fence_chain_for_each(tmp, &chain->base)
+		++count;
+
+	fences = kmalloc_array(count, sizeof(*fences), GFP_KERNEL);
+	if (!fences)
+		return -ENOMEM;
+
+	count = 0;
+	dma_fence_chain_for_each(tmp, &chain->base)
+		fences[count++] = dma_fence_get(tmp);
+
+	array = dma_fence_array_create(count, fences,
+				       dma_fence_context_alloc(1),
+				       1, false);
+	if (!array)
+		goto free_fences;
+
+	dma_fence_put(*f);
+	*f = &array->base;
+	return 0;
+
+free_fences:
+	while (count--)
+		dma_fence_put(fences[count]);
+
+	kfree(fences);
+	return -ENOMEM;
+}
+
 static int drm_syncobj_transfer_to_timeline(struct drm_file *file_private,
 					    struct drm_syncobj_transfer *args)
 {
 	struct drm_syncobj *timeline_syncobj = NULL;
-	struct dma_fence *fence;
 	struct dma_fence_chain *chain;
+	struct dma_fence *fence;
 	int ret;
 
 	timeline_syncobj = drm_syncobj_find(file_private, args->dst_handle);
@@ -860,16 +914,22 @@
 				     args->src_point, args->flags,
 				     &fence);
 	if (ret)
-		goto err;
+		goto err_put_timeline;
+
+	ret = drm_syncobj_flatten_chain(&fence);
+	if (ret)
+		goto err_free_fence;
+
 	chain = dma_fence_chain_alloc();
 	if (!chain) {
 		ret = -ENOMEM;
-		goto err1;
+		goto err_free_fence;
 	}
+
 	drm_syncobj_add_point(timeline_syncobj, chain, fence, args->dst_point);
-err1:
+err_free_fence:
 	dma_fence_put(fence);
-err:
+err_put_timeline:
 	drm_syncobj_put(timeline_syncobj);
 
 	return ret;
@@ -961,7 +1021,8 @@
 	uint64_t *points;
 	uint32_t signaled_count, i;
 
-	if (flags & DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT)
+	if (flags & (DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT |
+		     DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE))
 		lockdep_assert_none_held_once();
 
 	points = kmalloc_array(count, sizeof(*points), GFP_KERNEL);
@@ -996,7 +1057,8 @@
 		fence = drm_syncobj_fence_get(syncobjs[i]);
 		if (!fence || dma_fence_chain_find_seqno(&fence, points[i])) {
 			dma_fence_put(fence);
-			if (flags & DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT) {
+			if (flags & (DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT |
+				     DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE)) {
 				continue;
 			} else {
 				timeout = -EINVAL;
@@ -1029,7 +1091,8 @@
 	 * fallthough and try a 0 timeout wait!
 	 */
 
-	if (flags & DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT) {
+	if (flags & (DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT |
+		     DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE)) {
 		for (i = 0; i < count; ++i)
 			drm_syncobj_fence_add_wait(syncobjs[i], &entries[i]);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_buffer.c
@@ -481,7 +481,8 @@
 	} else {
 		CMD_LOAD_STATE(buffer, VIVS_GL_FLUSH_CACHE,
 				       VIVS_GL_FLUSH_CACHE_DEPTH |
-				       VIVS_GL_FLUSH_CACHE_COLOR);
+				       VIVS_GL_FLUSH_CACHE_COLOR |
+				       VIVS_GL_FLUSH_CACHE_SHADER_L1);
 		if (has_blt) {
 			CMD_LOAD_STATE(buffer, VIVS_BLT_ENABLE, 0x1);
 			CMD_LOAD_STATE(buffer, VIVS_BLT_SET_COMMAND, 0x1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_drv.c
@@ -488,7 +488,7 @@
 	.desc               = "etnaviv DRM",
 	.date               = "20151214",
 	.major              = 1,
-	.minor              = 3,
+	.minor              = 4,
 };
 
 /*
@@ -519,6 +519,16 @@
 	priv->num_gpus = 0;
 	priv->shm_gfp_mask = GFP_HIGHUSER | __GFP_RETRY_MAYFAIL | __GFP_NOWARN;
 
+	/*
+	 * If the GPU is part of a system with DMA addressing limitations,
+	 * request pages for our SHM backend buffers from the DMA32 zone to
+	 * hopefully avoid performance killing SWIOTLB bounce buffering.
+	 */
+	if (dma_addressing_limited(dev)) {
+		priv->shm_gfp_mask |= GFP_DMA32;
+		priv->shm_gfp_mask &= ~__GFP_HIGHMEM;
+	}
+
 	priv->cmdbuf_suballoc = etnaviv_cmdbuf_suballoc_new(drm->dev);
 	if (IS_ERR(priv->cmdbuf_suballoc)) {
 		dev_err(drm->dev, "Failed to create cmdbuf suballocator\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_dump.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_dump.c
@@ -83,10 +83,15 @@
 {
 	struct etnaviv_dump_registers *reg = iter->data;
 	unsigned int i;
+	u32 read_addr;
 
 	for (i = 0; i < ARRAY_SIZE(etnaviv_dump_registers); i++, reg++) {
+		read_addr = etnaviv_dump_registers[i];
+		if (read_addr >= VIVS_PM_POWER_CONTROLS &&
+		    read_addr <= VIVS_PM_PULSE_EATER)
+			read_addr = gpu_fix_power_address(gpu, read_addr);
 		reg->reg = cpu_to_le32(etnaviv_dump_registers[i]);
-		reg->value = cpu_to_le32(gpu_read(gpu, etnaviv_dump_registers[i]));
+		reg->value = cpu_to_le32(gpu_read(gpu, read_addr));
 	}
 
 	etnaviv_core_dump_header(iter, ETDUMP_BUF_REG, reg);
@@ -125,9 +130,9 @@
 		return;
 	etnaviv_dump_core = false;
 
-	mutex_lock(&gpu->mmu_context->lock);
+	mutex_lock(&submit->mmu_context->lock);
 
-	mmu_size = etnaviv_iommu_dump_size(gpu->mmu_context);
+	mmu_size = etnaviv_iommu_dump_size(submit->mmu_context);
 
 	/* We always dump registers, mmu, ring, hanging cmdbuf and end marker */
 	n_obj = 5;
@@ -157,7 +162,7 @@
 	iter.start = __vmalloc(file_size, GFP_KERNEL | __GFP_NOWARN |
 			__GFP_NORETRY);
 	if (!iter.start) {
-		mutex_unlock(&gpu->mmu_context->lock);
+		mutex_unlock(&submit->mmu_context->lock);
 		dev_warn(gpu->dev, "failed to allocate devcoredump file\n");
 		return;
 	}
@@ -169,18 +174,18 @@
 	memset(iter.hdr, 0, iter.data - iter.start);
 
 	etnaviv_core_dump_registers(&iter, gpu);
-	etnaviv_core_dump_mmu(&iter, gpu->mmu_context, mmu_size);
+	etnaviv_core_dump_mmu(&iter, submit->mmu_context, mmu_size);
 	etnaviv_core_dump_mem(&iter, ETDUMP_BUF_RING, gpu->buffer.vaddr,
 			      gpu->buffer.size,
 			      etnaviv_cmdbuf_get_va(&gpu->buffer,
-					&gpu->mmu_context->cmdbuf_mapping));
+					&submit->mmu_context->cmdbuf_mapping));
 
 	etnaviv_core_dump_mem(&iter, ETDUMP_BUF_CMD,
 			      submit->cmdbuf.vaddr, submit->cmdbuf.size,
 			      etnaviv_cmdbuf_get_va(&submit->cmdbuf,
-					&gpu->mmu_context->cmdbuf_mapping));
+					&submit->mmu_context->cmdbuf_mapping));
 
-	mutex_unlock(&gpu->mmu_context->lock);
+	mutex_unlock(&submit->mmu_context->lock);
 
 	/* Reserve space for the bomap */
 	if (n_bomap_pages) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_gem.c
@@ -340,6 +340,7 @@
 static void *etnaviv_gem_vmap_impl(struct etnaviv_gem_object *obj)
 {
 	struct page **pages;
+	pgprot_t prot;
 
 	lockdep_assert_held(&obj->lock);
 
@@ -347,15 +348,28 @@
 	if (IS_ERR(pages))
 		return NULL;
 
-	return vmap(pages, obj->base.size >> PAGE_SHIFT,
-			VM_MAP, pgprot_writecombine(PAGE_KERNEL));
+	switch (obj->flags & ETNA_BO_CACHE_MASK) {
+	case ETNA_BO_CACHED:
+		prot = PAGE_KERNEL;
+		break;
+	case ETNA_BO_UNCACHED:
+		prot = pgprot_noncached(PAGE_KERNEL);
+		break;
+	case ETNA_BO_WC:
+	default:
+		prot = pgprot_writecombine(PAGE_KERNEL);
+	}
+
+	return vmap(pages, obj->base.size >> PAGE_SHIFT, VM_MAP, prot);
 }
 
 static inline enum dma_data_direction etnaviv_op_to_dma_dir(u32 op)
 {
-	if (op & ETNA_PREP_READ)
+	op &= ETNA_PREP_READ | ETNA_PREP_WRITE;
+
+	if (op == ETNA_PREP_READ)
 		return DMA_FROM_DEVICE;
-	else if (op & ETNA_PREP_WRITE)
+	else if (op == ETNA_PREP_WRITE)
 		return DMA_TO_DEVICE;
 	else
 		return DMA_BIDIRECTIONAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_gem_prime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_gem_prime.c
@@ -88,7 +88,15 @@
 static int etnaviv_gem_prime_mmap_obj(struct etnaviv_gem_object *etnaviv_obj,
 		struct vm_area_struct *vma)
 {
-	return dma_buf_mmap(etnaviv_obj->base.dma_buf, vma, 0);
+	int ret;
+
+	ret = dma_buf_mmap(etnaviv_obj->base.dma_buf, vma, 0);
+	if (!ret) {
+		/* Drop the reference acquired by drm_gem_mmap_obj(). */
+		drm_gem_object_put(&etnaviv_obj->base);
+	}
+
+	return ret;
 }
 
 static const struct etnaviv_gem_ops etnaviv_gem_prime_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_gem_submit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_gem_submit.c
@@ -469,6 +469,12 @@
 		return -EINVAL;
 	}
 
+	if (args->stream_size > SZ_128K || args->nr_relocs > SZ_128K ||
+	    args->nr_bos > SZ_128K || args->nr_pmrs > 128) {
+		DRM_ERROR("submit arguments out of size limits\n");
+		return -EINVAL;
+	}
+
 	/*
 	 * Copy the command submission and bo array to kernel space in
 	 * one go, and do this outside of any locks.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_gpu.c
@@ -416,6 +416,12 @@
 	if (gpu->identity.model == chipModel_GC700)
 		gpu->identity.features &= ~chipFeatures_FAST_CLEAR;
 
+	/* These models/revisions don't have the 2D pipe bit */
+	if ((gpu->identity.model == chipModel_GC500 &&
+	     gpu->identity.revision <= 2) ||
+	    gpu->identity.model == chipModel_GC300)
+		gpu->identity.features |= chipFeatures_PIPE_2D;
+
 	if ((gpu->identity.model == chipModel_GC500 &&
 	     gpu->identity.revision < 2) ||
 	    (gpu->identity.model == chipModel_GC300 &&
@@ -449,8 +455,9 @@
 				gpu_read(gpu, VIVS_HI_CHIP_MINOR_FEATURE_5);
 	}
 
-	/* GC600 idle register reports zero bits where modules aren't present */
-	if (gpu->identity.model == chipModel_GC600)
+	/* GC600/300 idle register reports zero bits where modules aren't present */
+	if (gpu->identity.model == chipModel_GC600 ||
+	    gpu->identity.model == chipModel_GC300)
 		gpu->idle_mask = VIVS_HI_IDLE_STATE_TX |
 				 VIVS_HI_IDLE_STATE_RA |
 				 VIVS_HI_IDLE_STATE_SE |
@@ -583,7 +590,7 @@
 	u32 pmc, ppc;
 
 	/* enable clock gating */
-	ppc = gpu_read(gpu, VIVS_PM_POWER_CONTROLS);
+	ppc = gpu_read_power(gpu, VIVS_PM_POWER_CONTROLS);
 	ppc |= VIVS_PM_POWER_CONTROLS_ENABLE_MODULE_CLOCK_GATING;
 
 	/* Disable stall module clock gating for 4.3.0.1 and 4.3.0.2 revs */
@@ -591,9 +598,9 @@
 	    gpu->identity.revision == 0x4302)
 		ppc |= VIVS_PM_POWER_CONTROLS_DISABLE_STALL_MODULE_CLOCK_GATING;
 
-	gpu_write(gpu, VIVS_PM_POWER_CONTROLS, ppc);
+	gpu_write_power(gpu, VIVS_PM_POWER_CONTROLS, ppc);
 
-	pmc = gpu_read(gpu, VIVS_PM_MODULE_CONTROLS);
+	pmc = gpu_read_power(gpu, VIVS_PM_MODULE_CONTROLS);
 
 	/* Disable PA clock gating for GC400+ without bugfix except for GC420 */
 	if (gpu->identity.model >= chipModel_GC400 &&
@@ -628,7 +635,7 @@
 	pmc |= VIVS_PM_MODULE_CONTROLS_DISABLE_MODULE_CLOCK_GATING_RA_HZ;
 	pmc |= VIVS_PM_MODULE_CONTROLS_DISABLE_MODULE_CLOCK_GATING_RA_EZ;
 
-	gpu_write(gpu, VIVS_PM_MODULE_CONTROLS, pmc);
+	gpu_write_power(gpu, VIVS_PM_MODULE_CONTROLS, pmc);
 }
 
 void etnaviv_gpu_start_fe(struct etnaviv_gpu *gpu, u32 address, u16 prefetch)
@@ -688,11 +695,11 @@
 	    (gpu->identity.features & chipFeatures_PIPE_3D))
 	{
 		/* Performance fix: disable internal DFS */
-		pulse_eater = gpu_read(gpu, VIVS_PM_PULSE_EATER);
+		pulse_eater = gpu_read_power(gpu, VIVS_PM_PULSE_EATER);
 		pulse_eater |= BIT(18);
 	}
 
-	gpu_write(gpu, VIVS_PM_PULSE_EATER, pulse_eater);
+	gpu_write_power(gpu, VIVS_PM_PULSE_EATER, pulse_eater);
 }
 
 static void etnaviv_gpu_hw_init(struct etnaviv_gpu *gpu)
@@ -791,14 +798,6 @@
 	if (ret)
 		goto fail;
 
-	/*
-	 * If the GPU is part of a system with DMA addressing limitations,
-	 * request pages for our SHM backend buffers from the DMA32 zone to
-	 * hopefully avoid performance killing SWIOTLB bounce buffering.
-	 */
-	if (dma_addressing_limited(gpu->dev))
-		priv->shm_gfp_mask |= GFP_DMA32;
-
 	/* Create buffer: */
 	ret = etnaviv_cmdbuf_init(priv->cmdbuf_suballoc, &gpu->buffer,
 				  PAGE_SIZE);
@@ -1293,10 +1292,12 @@
 {
 	u32 val;
 
+	mutex_lock(&gpu->lock);
+
 	/* disable clock gating */
-	val = gpu_read(gpu, VIVS_PM_POWER_CONTROLS);
+	val = gpu_read_power(gpu, VIVS_PM_POWER_CONTROLS);
 	val &= ~VIVS_PM_POWER_CONTROLS_ENABLE_MODULE_CLOCK_GATING;
-	gpu_write(gpu, VIVS_PM_POWER_CONTROLS, val);
+	gpu_write_power(gpu, VIVS_PM_POWER_CONTROLS, val);
 
 	/* enable debug register */
 	val = gpu_read(gpu, VIVS_HI_CLOCK_CONTROL);
@@ -1304,6 +1305,8 @@
 	gpu_write(gpu, VIVS_HI_CLOCK_CONTROL, val);
 
 	sync_point_perfmon_sample(gpu, event, ETNA_PM_PROCESS_PRE);
+
+	mutex_unlock(&gpu->lock);
 }
 
 static void sync_point_perfmon_sample_post(struct etnaviv_gpu *gpu,
@@ -1313,13 +1316,9 @@
 	unsigned int i;
 	u32 val;
 
-	sync_point_perfmon_sample(gpu, event, ETNA_PM_PROCESS_POST);
-
-	for (i = 0; i < submit->nr_pmrs; i++) {
-		const struct etnaviv_perfmon_request *pmr = submit->pmrs + i;
+	mutex_lock(&gpu->lock);
 
-		*pmr->bo_vma = pmr->sequence;
-	}
+	sync_point_perfmon_sample(gpu, event, ETNA_PM_PROCESS_POST);
 
 	/* disable debug register */
 	val = gpu_read(gpu, VIVS_HI_CLOCK_CONTROL);
@@ -1327,9 +1326,17 @@
 	gpu_write(gpu, VIVS_HI_CLOCK_CONTROL, val);
 
 	/* enable clock gating */
-	val = gpu_read(gpu, VIVS_PM_POWER_CONTROLS);
+	val = gpu_read_power(gpu, VIVS_PM_POWER_CONTROLS);
 	val |= VIVS_PM_POWER_CONTROLS_ENABLE_MODULE_CLOCK_GATING;
-	gpu_write(gpu, VIVS_PM_POWER_CONTROLS, val);
+	gpu_write_power(gpu, VIVS_PM_POWER_CONTROLS, val);
+
+	mutex_unlock(&gpu->lock);
+
+	for (i = 0; i < submit->nr_pmrs; i++) {
+		const struct etnaviv_perfmon_request *pmr = submit->pmrs + i;
+
+		*pmr->bo_vma = pmr->sequence;
+	}
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_gpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_gpu.h
@@ -10,6 +10,7 @@
 #include "etnaviv_gem.h"
 #include "etnaviv_mmu.h"
 #include "etnaviv_drv.h"
+#include "common.xml.h"
 
 struct etnaviv_gem_submit;
 struct etnaviv_vram_mapping;
@@ -130,6 +131,7 @@
 
 	/* hang detection */
 	u32 hangcheck_dma_addr;
+	u32 hangcheck_fence;
 
 	void __iomem *mmio;
 	int irq;
@@ -158,6 +160,26 @@
 	return readl(gpu->mmio + reg);
 }
 
+static inline u32 gpu_fix_power_address(struct etnaviv_gpu *gpu, u32 reg)
+{
+	/* Power registers in GC300 < 2.0 are offset by 0x100 */
+	if (gpu->identity.model == chipModel_GC300 &&
+	    gpu->identity.revision < 0x2000)
+		reg += 0x100;
+
+	return reg;
+}
+
+static inline void gpu_write_power(struct etnaviv_gpu *gpu, u32 reg, u32 data)
+{
+	writel(data, gpu->mmio + gpu_fix_power_address(gpu, reg));
+}
+
+static inline u32 gpu_read_power(struct etnaviv_gpu *gpu, u32 reg)
+{
+	return readl(gpu->mmio + gpu_fix_power_address(gpu, reg));
+}
+
 int etnaviv_gpu_get_param(struct etnaviv_gpu *gpu, u32 param, u64 *value);
 
 int etnaviv_gpu_init(struct etnaviv_gpu *gpu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_hwdb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_hwdb.c
@@ -135,6 +135,9 @@
 bool etnaviv_fill_identity_from_hwdb(struct etnaviv_gpu *gpu)
 {
 	struct etnaviv_chip_identity *ident = &gpu->identity;
+	const u32 product_id = ident->product_id;
+	const u32 customer_id = ident->customer_id;
+	const u32 eco_id = ident->eco_id;
 	int i;
 
 	for (i = 0; i < ARRAY_SIZE(etnaviv_chip_identities); i++) {
@@ -148,6 +151,12 @@
 			 etnaviv_chip_identities[i].eco_id == ~0U)) {
 			memcpy(ident, &etnaviv_chip_identities[i],
 			       sizeof(*ident));
+
+			/* Restore some id values as ~0U aka 'don't care' might been used. */
+			ident->product_id = product_id;
+			ident->customer_id = customer_id;
+			ident->eco_id = eco_id;
+
 			return true;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_mmu.c
@@ -80,10 +80,10 @@
 		return -EINVAL;
 
 	for_each_sgtable_dma_sg(sgt, sg, i) {
-		u32 pa = sg_dma_address(sg) - sg->offset;
+		phys_addr_t pa = sg_dma_address(sg) - sg->offset;
 		size_t bytes = sg_dma_len(sg) + sg->offset;
 
-		VERB("map[%d]: %08x %08x(%zx)", i, iova, pa, bytes);
+		VERB("map[%d]: %08x %pap(%zx)", i, iova, &pa, bytes);
 
 		ret = etnaviv_context_map(context, da, pa, bytes, prot);
 		if (ret)
@@ -286,6 +286,12 @@
 
 	mutex_lock(&context->lock);
 
+	/* Bail if the mapping has been reaped by another thread */
+	if (!mapping->context) {
+		mutex_unlock(&context->lock);
+		return;
+	}
+
 	/* If the vram node is on the mm, unmap and remove the node */
 	if (mapping->vram_node.mm == &context->mm)
 		etnaviv_iommu_remove_mapping(context, mapping);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/etnaviv/etnaviv_sched.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/etnaviv/etnaviv_sched.c
@@ -107,8 +107,10 @@
 	 */
 	dma_addr = gpu_read(gpu, VIVS_FE_DMA_ADDRESS);
 	change = dma_addr - gpu->hangcheck_dma_addr;
-	if (change < 0 || change > 16) {
+	if (gpu->completed_fence != gpu->hangcheck_fence ||
+	    change < 0 || change > 16) {
 		gpu->hangcheck_dma_addr = dma_addr;
+		gpu->hangcheck_fence = gpu->completed_fence;
 		goto out_no_timeout;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos5433_drm_decon.c
@@ -317,9 +317,9 @@
 static void decon_win_set_pixfmt(struct decon_context *ctx, unsigned int win,
 				 struct drm_framebuffer *fb)
 {
-	struct exynos_drm_plane plane = ctx->planes[win];
+	struct exynos_drm_plane *plane = &ctx->planes[win];
 	struct exynos_drm_plane_state *state =
-		to_exynos_plane_state(plane.base.state);
+		to_exynos_plane_state(plane->base.state);
 	unsigned int alpha = state->base.alpha;
 	unsigned int pixel_alpha;
 	unsigned long val;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos7_drm_decon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos7_drm_decon.c
@@ -806,31 +806,40 @@
 	if (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to prepare_enable the pclk [%d]\n",
 			      ret);
-		return ret;
+		goto err_pclk_enable;
 	}
 
 	ret = clk_prepare_enable(ctx->aclk);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to prepare_enable the aclk [%d]\n",
 			      ret);
-		return ret;
+		goto err_aclk_enable;
 	}
 
 	ret = clk_prepare_enable(ctx->eclk);
 	if  (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to prepare_enable the eclk [%d]\n",
 			      ret);
-		return ret;
+		goto err_eclk_enable;
 	}
 
 	ret = clk_prepare_enable(ctx->vclk);
 	if  (ret < 0) {
 		DRM_DEV_ERROR(dev, "Failed to prepare_enable the vclk [%d]\n",
 			      ret);
-		return ret;
+		goto err_vclk_enable;
 	}
 
 	return 0;
+
+err_vclk_enable:
+	clk_disable_unprepare(ctx->eclk);
+err_eclk_enable:
+	clk_disable_unprepare(ctx->aclk);
+err_aclk_enable:
+	clk_disable_unprepare(ctx->pclk);
+err_pclk_enable:
+	return ret;
 }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_crtc.c
@@ -39,13 +39,12 @@
 	if (exynos_crtc->ops->atomic_disable)
 		exynos_crtc->ops->atomic_disable(exynos_crtc);
 
+	spin_lock_irq(&crtc->dev->event_lock);
 	if (crtc->state->event && !crtc->state->active) {
-		spin_lock_irq(&crtc->dev->event_lock);
 		drm_crtc_send_vblank_event(crtc, crtc->state->event);
-		spin_unlock_irq(&crtc->dev->event_lock);
-
 		crtc->state->event = NULL;
 	}
+	spin_unlock_irq(&crtc->dev->event_lock);
 }
 
 static int exynos_crtc_atomic_check(struct drm_crtc *crtc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_dma.c
@@ -108,18 +108,16 @@
 		return 0;
 
 	if (!priv->mapping) {
-		void *mapping;
+		void *mapping = NULL;
 
 		if (IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU))
 			mapping = arm_iommu_create_mapping(&platform_bus_type,
 				EXYNOS_DEV_ADDR_START, EXYNOS_DEV_ADDR_SIZE);
 		else if (IS_ENABLED(CONFIG_IOMMU_DMA))
 			mapping = iommu_get_domain_for_dev(priv->dma_dev);
-		else
-			mapping = ERR_PTR(-ENODEV);
 
-		if (IS_ERR(mapping))
-			return PTR_ERR(mapping);
+		if (!mapping)
+			return -ENODEV;
 		priv->mapping = mapping;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_drv.c
@@ -324,6 +324,7 @@
 	drm_mode_config_cleanup(drm);
 	exynos_drm_cleanup_dma(drm);
 	kfree(private);
+	dev_set_drvdata(dev, NULL);
 err_free_drm:
 	drm_dev_put(drm);
 
@@ -338,6 +339,7 @@
 
 	exynos_drm_fbdev_fini(drm);
 	drm_kms_helper_poll_fini(drm);
+	drm_atomic_helper_shutdown(drm);
 
 	component_unbind_all(drm->dev, drm);
 	drm_mode_config_cleanup(drm);
@@ -375,9 +377,18 @@
 	return 0;
 }
 
+static void exynos_drm_platform_shutdown(struct platform_device *pdev)
+{
+	struct drm_device *drm = platform_get_drvdata(pdev);
+
+	if (drm)
+		drm_atomic_helper_shutdown(drm);
+}
+
 static struct platform_driver exynos_drm_platform_driver = {
 	.probe	= exynos_drm_platform_probe,
 	.remove	= exynos_drm_platform_remove,
+	.shutdown = exynos_drm_platform_shutdown,
 	.driver	= {
 		.name	= "exynos-drm",
 		.pm	= &exynos_drm_pm_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -809,15 +809,15 @@
 			reg |= DSIM_AUTO_MODE;
 		if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_HSE)
 			reg |= DSIM_HSE_MODE;
-		if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HFP))
+		if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HFP)
 			reg |= DSIM_HFP_MODE;
-		if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HBP))
+		if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HBP)
 			reg |= DSIM_HBP_MODE;
-		if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HSA))
+		if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HSA)
 			reg |= DSIM_HSA_MODE;
 	}
 
-	if (!(dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET))
+	if (dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET)
 		reg |= DSIM_EOT_DISABLE;
 
 	switch (dsi->format) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_fimd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_fimd.c
@@ -644,9 +644,9 @@
 static void fimd_win_set_pixfmt(struct fimd_context *ctx, unsigned int win,
 				struct drm_framebuffer *fb, int width)
 {
-	struct exynos_drm_plane plane = ctx->planes[win];
+	struct exynos_drm_plane *plane = &ctx->planes[win];
 	struct exynos_drm_plane_state *state =
-		to_exynos_plane_state(plane.base.state);
+		to_exynos_plane_state(plane->base.state);
 	uint32_t pixel_format = fb->format->format;
 	unsigned int alpha = state->base.alpha;
 	u32 val = WINCONx_ENWIN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_g2d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_g2d.c
@@ -1335,7 +1335,7 @@
 	/* Let the runqueue know that there is work to do. */
 	queue_work(g2d->g2d_workq, &g2d->runqueue_work);
 
-	if (runqueue_node->async)
+	if (req->async)
 		goto out;
 
 	wait_for_completion(&runqueue_node->complete);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_g2d.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_g2d.h
@@ -34,11 +34,11 @@
 	return -ENODEV;
 }
 
-int g2d_open(struct drm_device *drm_dev, struct drm_file *file)
+static inline int g2d_open(struct drm_device *drm_dev, struct drm_file *file)
 {
 	return 0;
 }
 
-void g2d_close(struct drm_device *drm_dev, struct drm_file *file)
+static inline void g2d_close(struct drm_device *drm_dev, struct drm_file *file)
 { }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_gsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_gsc.c
@@ -1173,7 +1173,7 @@
 	struct exynos_drm_ipp *ipp = &ctx->ipp;
 
 	ctx->drm_dev = drm_dev;
-	ctx->drm_dev = drm_dev;
+	ipp->drm_dev = drm_dev;
 	exynos_drm_register_dma(drm_dev, dev, &ctx->dma_priv);
 
 	exynos_drm_ipp_register(dev, ipp, &ipp_funcs,
@@ -1346,7 +1346,7 @@
 	for (i = 0; i < ctx->num_clocks; i++) {
 		ret = clk_prepare_enable(ctx->clocks[i]);
 		if (ret) {
-			while (--i > 0)
+			while (--i >= 0)
 				clk_disable_unprepare(ctx->clocks[i]);
 			return ret;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_drm_vidi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_drm_vidi.c
@@ -308,6 +308,7 @@
 	struct vidi_context *ctx = ctx_from_connector(connector);
 	struct edid *edid;
 	int edid_len;
+	int count;
 
 	/*
 	 * the edid data comes from user side and it would be set
@@ -315,19 +316,23 @@
 	 */
 	if (!ctx->raw_edid) {
 		DRM_DEV_DEBUG_KMS(ctx->dev, "raw_edid is null.\n");
-		return -EFAULT;
+		return 0;
 	}
 
 	edid_len = (1 + ctx->raw_edid->extensions) * EDID_LENGTH;
 	edid = kmemdup(ctx->raw_edid, edid_len, GFP_KERNEL);
 	if (!edid) {
 		DRM_DEV_DEBUG_KMS(ctx->dev, "failed to allocate edid\n");
-		return -ENOMEM;
+		return 0;
 	}
 
 	drm_connector_update_edid_property(connector, edid);
 
-	return drm_add_edid_modes(connector, edid);
+	count = drm_add_edid_modes(connector, edid);
+
+	kfree(edid);
+
+	return count;
 }
 
 static const struct drm_connector_helper_funcs vidi_connector_helper_funcs = {
@@ -468,8 +473,6 @@
 	if (ctx->raw_edid != (struct edid *)fake_edid_info) {
 		kfree(ctx->raw_edid);
 		ctx->raw_edid = NULL;
-
-		return -EINVAL;
 	}
 
 	component_del(&pdev->dev, &vidi_component_ops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/exynos/exynos_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/exynos/exynos_hdmi.c
@@ -887,11 +887,11 @@
 	int ret;
 
 	if (!hdata->ddc_adpt)
-		return -ENODEV;
+		goto no_edid;
 
 	edid = drm_get_edid(connector, hdata->ddc_adpt);
 	if (!edid)
-		return -ENODEV;
+		goto no_edid;
 
 	hdata->dvi_mode = !drm_detect_hdmi_monitor(edid);
 	DRM_DEV_DEBUG_KMS(hdata->dev, "%s : width[%d] x height[%d]\n",
@@ -906,6 +906,9 @@
 	kfree(edid);
 
 	return ret;
+
+no_edid:
+	return drm_add_modes_noedid(connector, 640, 480);
 }
 
 static int hdmi_find_phy_conf(struct hdmi_context *hdata, u32 pixel_clock)
@@ -1861,6 +1864,8 @@
 		return ret;
 
 	crtc = exynos_drm_crtc_get_by_type(drm_dev, EXYNOS_DISPLAY_TYPE_HDMI);
+	if (IS_ERR(crtc))
+		return PTR_ERR(crtc);
 	crtc->pipe_clk = &hdata->phy_clk;
 
 	ret = hdmi_create_connector(encoder);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/fsl-dcu/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/fsl-dcu/Kconfig
@@ -8,6 +8,7 @@
 	select DRM_PANEL
 	select REGMAP_MMIO
 	select VIDEOMODE_HELPERS
+	select MFD_SYSCON if SOC_LS1021A
 	help
 	  Choose this option if you have an Freescale DCU chipset.
 	  If M is selected the module will be called fsl-dcu-drm.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c
@@ -100,6 +100,7 @@
 static int fsl_dcu_load(struct drm_device *dev, unsigned long flags)
 {
 	struct fsl_dcu_drm_device *fsl_dev = dev->dev_private;
+	struct regmap *scfg;
 	int ret;
 
 	ret = fsl_dcu_drm_modeset_init(fsl_dev);
@@ -108,6 +109,20 @@
 		return ret;
 	}
 
+	scfg = syscon_regmap_lookup_by_compatible("fsl,ls1021a-scfg");
+	if (PTR_ERR(scfg) != -ENODEV) {
+		/*
+		 * For simplicity, enable the PIXCLK unconditionally,
+		 * resulting in increased power consumption. Disabling
+		 * the clock in PM or on unload could be implemented as
+		 * a future improvement.
+		 */
+		ret = regmap_update_bits(scfg, SCFG_PIXCLKCR, SCFG_PIXCLKCR_PXCEN,
+					 SCFG_PIXCLKCR_PXCEN);
+		if (ret < 0)
+			return dev_err_probe(dev->dev, ret, "failed to enable pixclk\n");
+	}
+
 	ret = drm_vblank_init(dev, dev->mode_config.num_crtc);
 	if (ret < 0) {
 		dev_err(dev->dev, "failed to initialize vblank\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h
@@ -160,6 +160,9 @@
 #define FSL_DCU_ARGB4444		12
 #define FSL_DCU_YUV422			14
 
+#define SCFG_PIXCLKCR			0x28
+#define SCFG_PIXCLKCR_PXCEN		BIT(31)
+
 #define VF610_LAYER_REG_NUM		9
 #define LS1021A_LAYER_REG_NUM		10
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_rgb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_rgb.c
@@ -60,8 +60,9 @@
 	return drm_panel_get_modes(fsl_connector->panel, connector);
 }
 
-static int fsl_dcu_drm_connector_mode_valid(struct drm_connector *connector,
-					    struct drm_display_mode *mode)
+static enum drm_mode_status
+fsl_dcu_drm_connector_mode_valid(struct drm_connector *connector,
+				 struct drm_display_mode *mode)
 {
 	if (mode->hdisplay & 0xf)
 		return MODE_ERROR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/gma500/cdv_intel_lvds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/gma500/cdv_intel_lvds.c
@@ -310,6 +310,9 @@
 	if (mode_dev->panel_fixed_mode != NULL) {
 		struct drm_display_mode *mode =
 		    drm_mode_duplicate(dev, mode_dev->panel_fixed_mode);
+		if (!mode)
+			return 0;
+
 		drm_mode_probed_add(connector, mode);
 		return 1;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/gma500/gma_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/gma500/gma_display.c
@@ -529,15 +529,18 @@
 		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
 
 		gma_crtc->page_flip_event = event;
+		spin_unlock_irqrestore(&dev->event_lock, flags);
 
 		/* Call this locked if we want an event at vblank interrupt. */
 		ret = crtc_funcs->mode_set_base(crtc, crtc->x, crtc->y, old_fb);
 		if (ret) {
-			gma_crtc->page_flip_event = NULL;
-			drm_crtc_vblank_put(crtc);
+			spin_lock_irqsave(&dev->event_lock, flags);
+			if (gma_crtc->page_flip_event) {
+				gma_crtc->page_flip_event = NULL;
+				drm_crtc_vblank_put(crtc);
+			}
+			spin_unlock_irqrestore(&dev->event_lock, flags);
 		}
-
-		spin_unlock_irqrestore(&dev->event_lock, flags);
 	} else {
 		ret = crtc_funcs->mode_set_base(crtc, crtc->x, crtc->y, old_fb);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/gma500/mid_bios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/gma500/mid_bios.c
@@ -280,6 +280,11 @@
 					    0, PCI_DEVFN(2, 0));
 	int ret = -1;
 
+	if (pci_gfx_root == NULL) {
+		WARN_ON(1);
+		return;
+	}
+
 	/* Get the address of the platform config vbt */
 	pci_read_config_dword(pci_gfx_root, 0xFC, &addr);
 	pci_dev_put(pci_gfx_root);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/gma500/psb_intel_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/gma500/psb_intel_display.c
@@ -536,14 +536,15 @@
 
 struct drm_crtc *psb_intel_get_crtc_from_pipe(struct drm_device *dev, int pipe)
 {
-	struct drm_crtc *crtc = NULL;
+	struct drm_crtc *crtc;
 
 	list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
 		struct gma_crtc *gma_crtc = to_gma_crtc(crtc);
+
 		if (gma_crtc->pipe == pipe)
-			break;
+			return crtc;
 	}
-	return crtc;
+	return NULL;
 }
 
 int gma_connector_clones(struct drm_device *dev, int type_mask)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/gma500/psb_intel_lvds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/gma500/psb_intel_lvds.c
@@ -508,6 +508,9 @@
 	if (mode_dev->panel_fixed_mode != NULL) {
 		struct drm_display_mode *mode =
 		    drm_mode_duplicate(dev, mode_dev->panel_fixed_mode);
+		if (!mode)
+			return 0;
+
 		drm_mode_probed_add(connector, mode);
 		return 1;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/hisilicon/hibmc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/hisilicon/hibmc/Kconfig
@@ -1,7 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config DRM_HISI_HIBMC
 	tristate "DRM Support for Hisilicon Hibmc"
-	depends on DRM && PCI && ARM64
+	depends on DRM && PCI && (ARM64 || COMPILE_TEST)
+	depends on MMU
 	select DRM_KMS_HELPER
 	select DRM_VRAM_HELPER
 	select DRM_TTM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/hyperv/hyperv_drm_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/hyperv/hyperv_drm_drv.c
@@ -198,8 +198,6 @@
 	if (ret)
 		drm_warn(dev, "Failed to update vram location.\n");
 
-	hv->dirt_needed = true;
-
 	ret = hyperv_mode_config_init(hv);
 	if (ret)
 		goto err_vmbus_close;
@@ -225,12 +223,29 @@
 {
 	struct drm_device *dev = hv_get_drvdata(hdev);
 	struct hyperv_drm_device *hv = to_hv(dev);
+	struct pci_dev *pdev;
 
 	drm_dev_unplug(dev);
 	drm_atomic_helper_shutdown(dev);
 	vmbus_close(hdev->channel);
 	hv_set_drvdata(hdev, NULL);
-	vmbus_free_mmio(hv->mem->start, hv->fb_size);
+
+	/*
+	 * Free allocated MMIO memory only on Gen2 VMs.
+	 * On Gen1 VMs, release the PCI device
+	 */
+	if (efi_enabled(EFI_BOOT)) {
+		vmbus_free_mmio(hv->mem->start, hv->fb_size);
+	} else {
+		pdev = pci_get_device(PCI_VENDOR_ID_MICROSOFT,
+				      PCI_DEVICE_ID_HYPERV_VIDEO, NULL);
+		if (!pdev) {
+			drm_err(dev, "Unable to find PCI Hyper-V video\n");
+			return -ENODEV;
+		}
+		pci_release_region(pdev, 0);
+		pci_dev_put(pdev);
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/hyperv/hyperv_drm_modeset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/hyperv/hyperv_drm_modeset.c
@@ -7,9 +7,11 @@
 
 #include <drm/drm_damage_helper.h>
 #include <drm/drm_drv.h>
+#include <drm/drm_edid.h>
 #include <drm/drm_fb_helper.h>
 #include <drm/drm_format_helper.h>
 #include <drm/drm_fourcc.h>
+#include <drm/drm_framebuffer.h>
 #include <drm/drm_gem_atomic_helper.h>
 #include <drm/drm_gem_framebuffer_helper.h>
 #include <drm/drm_gem_shmem_helper.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/Kconfig
@@ -101,6 +101,7 @@
 config DRM_I915_GVT
 	bool "Enable Intel GVT-g graphics virtualization host support"
 	depends on DRM_I915
+	depends on X86
 	depends on 64BIT
 	default n
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/Makefile
@@ -211,6 +211,8 @@
 	display/intel_dpio_phy.o \
 	display/intel_dpll.o \
 	display/intel_dpll_mgr.o \
+	display/intel_dpt.o \
+	display/intel_drrs.o \
 	display/intel_dsb.o \
 	display/intel_fb.o \
 	display/intel_fbc.o \
@@ -247,6 +249,7 @@
 	display/g4x_dp.o \
 	display/g4x_hdmi.o \
 	display/icl_dsi.o \
+	display/intel_backlight.o \
 	display/intel_crt.o \
 	display/intel_ddi.o \
 	display/intel_ddi_buf_trans.o \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/g4x_dp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/g4x_dp.c
@@ -7,6 +7,7 @@
 
 #include "g4x_dp.h"
 #include "intel_audio.h"
+#include "intel_backlight.h"
 #include "intel_connector.h"
 #include "intel_de.h"
 #include "intel_display_types.h"
@@ -16,7 +17,6 @@
 #include "intel_fifo_underrun.h"
 #include "intel_hdmi.h"
 #include "intel_hotplug.h"
-#include "intel_panel.h"
 #include "intel_pps.h"
 #include "intel_sideband.h"
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/g4x_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/g4x_hdmi.c
@@ -584,6 +584,7 @@
 		else
 			intel_encoder->enable = g4x_enable_hdmi;
 	}
+	intel_encoder->shutdown = intel_hdmi_encoder_shutdown;
 
 	intel_encoder->type = INTEL_OUTPUT_HDMI;
 	intel_encoder->power_domain = intel_port_to_power_domain(port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/icl_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -29,6 +29,7 @@
 #include <drm/drm_mipi_dsi.h>
 
 #include "intel_atomic.h"
+#include "intel_backlight.h"
 #include "intel_combo_phy.h"
 #include "intel_connector.h"
 #include "intel_crtc.h"
@@ -306,9 +307,21 @@
 {
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
+	i915_reg_t dss_ctl1_reg, dss_ctl2_reg;
 	u32 dss_ctl1;
 
-	dss_ctl1 = intel_de_read(dev_priv, DSS_CTL1);
+	/* FIXME: Move all DSS handling to intel_vdsc.c */
+	if (DISPLAY_VER(dev_priv) >= 12) {
+		struct intel_crtc *crtc = to_intel_crtc(pipe_config->uapi.crtc);
+
+		dss_ctl1_reg = ICL_PIPE_DSS_CTL1(crtc->pipe);
+		dss_ctl2_reg = ICL_PIPE_DSS_CTL2(crtc->pipe);
+	} else {
+		dss_ctl1_reg = DSS_CTL1;
+		dss_ctl2_reg = DSS_CTL2;
+	}
+
+	dss_ctl1 = intel_de_read(dev_priv, dss_ctl1_reg);
 	dss_ctl1 |= SPLITTER_ENABLE;
 	dss_ctl1 &= ~OVERLAP_PIXELS_MASK;
 	dss_ctl1 |= OVERLAP_PIXELS(intel_dsi->pixel_overlap);
@@ -329,16 +342,16 @@
 
 		dss_ctl1 &= ~LEFT_DL_BUF_TARGET_DEPTH_MASK;
 		dss_ctl1 |= LEFT_DL_BUF_TARGET_DEPTH(dl_buffer_depth);
-		dss_ctl2 = intel_de_read(dev_priv, DSS_CTL2);
+		dss_ctl2 = intel_de_read(dev_priv, dss_ctl2_reg);
 		dss_ctl2 &= ~RIGHT_DL_BUF_TARGET_DEPTH_MASK;
 		dss_ctl2 |= RIGHT_DL_BUF_TARGET_DEPTH(dl_buffer_depth);
-		intel_de_write(dev_priv, DSS_CTL2, dss_ctl2);
+		intel_de_write(dev_priv, dss_ctl2_reg, dss_ctl2);
 	} else {
 		/* Interleave */
 		dss_ctl1 |= DUAL_LINK_MODE_INTERLEAVE;
 	}
 
-	intel_de_write(dev_priv, DSS_CTL1, dss_ctl1);
+	intel_de_write(dev_priv, dss_ctl1_reg, dss_ctl1);
 }
 
 /* aka DSI 8X clock */
@@ -711,10 +724,7 @@
 	intel_de_write(dev_priv, ICL_DPCLKA_CFGCR0, val);
 
 	for_each_dsi_phy(phy, intel_dsi->phys) {
-		if (DISPLAY_VER(dev_priv) >= 12)
-			val |= ICL_DPCLKA_CFGCR0_DDI_CLK_OFF(phy);
-		else
-			val &= ~ICL_DPCLKA_CFGCR0_DDI_CLK_OFF(phy);
+		val &= ~ICL_DPCLKA_CFGCR0_DDI_CLK_OFF(phy);
 	}
 	intel_de_write(dev_priv, ICL_DPCLKA_CFGCR0, val);
 
@@ -1150,8 +1160,6 @@
 gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
 			      const struct intel_crtc_state *crtc_state)
 {
-	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-
 	/* step 4a: power up all lanes of the DDI used by DSI */
 	gen11_dsi_power_up_lanes(encoder);
 
@@ -1177,8 +1185,7 @@
 	gen11_dsi_configure_transcoder(encoder, crtc_state);
 
 	/* Step 4l: Gate DDI clocks */
-	if (DISPLAY_VER(dev_priv) == 11)
-		gen11_dsi_gate_clocks(encoder);
+	gen11_dsi_gate_clocks(encoder);
 }
 
 static void gen11_dsi_powerup_panel(struct intel_encoder *encoder)
@@ -1478,6 +1485,13 @@
 static enum drm_mode_status gen11_dsi_mode_valid(struct drm_connector *connector,
 						 struct drm_display_mode *mode)
 {
+	struct drm_i915_private *i915 = to_i915(connector->dev);
+	enum drm_mode_status status;
+
+	status = intel_cpu_transcoder_mode_valid(i915, mode);
+	if (status != MODE_OK)
+		return status;
+
 	/* FIXME: DSC? */
 	return intel_dsi_mode_valid(connector, mode);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_atomic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_atomic.c
@@ -40,6 +40,7 @@
 #include "intel_global_state.h"
 #include "intel_hdcp.h"
 #include "intel_psr.h"
+#include "intel_fb.h"
 #include "skl_universal_plane.h"
 
 /**
@@ -310,198 +311,6 @@
 	kfree(crtc_state);
 }
 
-static void intel_atomic_setup_scaler(struct intel_crtc_scaler_state *scaler_state,
-				      int num_scalers_need, struct intel_crtc *intel_crtc,
-				      const char *name, int idx,
-				      struct intel_plane_state *plane_state,
-				      int *scaler_id)
-{
-	struct drm_i915_private *dev_priv = to_i915(intel_crtc->base.dev);
-	int j;
-	u32 mode;
-
-	if (*scaler_id < 0) {
-		/* find a free scaler */
-		for (j = 0; j < intel_crtc->num_scalers; j++) {
-			if (scaler_state->scalers[j].in_use)
-				continue;
-
-			*scaler_id = j;
-			scaler_state->scalers[*scaler_id].in_use = 1;
-			break;
-		}
-	}
-
-	if (drm_WARN(&dev_priv->drm, *scaler_id < 0,
-		     "Cannot find scaler for %s:%d\n", name, idx))
-		return;
-
-	/* set scaler mode */
-	if (plane_state && plane_state->hw.fb &&
-	    plane_state->hw.fb->format->is_yuv &&
-	    plane_state->hw.fb->format->num_planes > 1) {
-		struct intel_plane *plane = to_intel_plane(plane_state->uapi.plane);
-		if (DISPLAY_VER(dev_priv) == 9) {
-			mode = SKL_PS_SCALER_MODE_NV12;
-		} else if (icl_is_hdr_plane(dev_priv, plane->id)) {
-			/*
-			 * On gen11+'s HDR planes we only use the scaler for
-			 * scaling. They have a dedicated chroma upsampler, so
-			 * we don't need the scaler to upsample the UV plane.
-			 */
-			mode = PS_SCALER_MODE_NORMAL;
-		} else {
-			struct intel_plane *linked =
-				plane_state->planar_linked_plane;
-
-			mode = PS_SCALER_MODE_PLANAR;
-
-			if (linked)
-				mode |= PS_PLANE_Y_SEL(linked->id);
-		}
-	} else if (DISPLAY_VER(dev_priv) >= 10) {
-		mode = PS_SCALER_MODE_NORMAL;
-	} else if (num_scalers_need == 1 && intel_crtc->num_scalers > 1) {
-		/*
-		 * when only 1 scaler is in use on a pipe with 2 scalers
-		 * scaler 0 operates in high quality (HQ) mode.
-		 * In this case use scaler 0 to take advantage of HQ mode
-		 */
-		scaler_state->scalers[*scaler_id].in_use = 0;
-		*scaler_id = 0;
-		scaler_state->scalers[0].in_use = 1;
-		mode = SKL_PS_SCALER_MODE_HQ;
-	} else {
-		mode = SKL_PS_SCALER_MODE_DYN;
-	}
-
-	drm_dbg_kms(&dev_priv->drm, "Attached scaler id %u.%u to %s:%d\n",
-		    intel_crtc->pipe, *scaler_id, name, idx);
-	scaler_state->scalers[*scaler_id].mode = mode;
-}
-
-/**
- * intel_atomic_setup_scalers() - setup scalers for crtc per staged requests
- * @dev_priv: i915 device
- * @intel_crtc: intel crtc
- * @crtc_state: incoming crtc_state to validate and setup scalers
- *
- * This function sets up scalers based on staged scaling requests for
- * a @crtc and its planes. It is called from crtc level check path. If request
- * is a supportable request, it attaches scalers to requested planes and crtc.
- *
- * This function takes into account the current scaler(s) in use by any planes
- * not being part of this atomic state
- *
- *  Returns:
- *         0 - scalers were setup succesfully
- *         error code - otherwise
- */
-int intel_atomic_setup_scalers(struct drm_i915_private *dev_priv,
-			       struct intel_crtc *intel_crtc,
-			       struct intel_crtc_state *crtc_state)
-{
-	struct drm_plane *plane = NULL;
-	struct intel_plane *intel_plane;
-	struct intel_plane_state *plane_state = NULL;
-	struct intel_crtc_scaler_state *scaler_state =
-		&crtc_state->scaler_state;
-	struct drm_atomic_state *drm_state = crtc_state->uapi.state;
-	struct intel_atomic_state *intel_state = to_intel_atomic_state(drm_state);
-	int num_scalers_need;
-	int i;
-
-	num_scalers_need = hweight32(scaler_state->scaler_users);
-
-	/*
-	 * High level flow:
-	 * - staged scaler requests are already in scaler_state->scaler_users
-	 * - check whether staged scaling requests can be supported
-	 * - add planes using scalers that aren't in current transaction
-	 * - assign scalers to requested users
-	 * - as part of plane commit, scalers will be committed
-	 *   (i.e., either attached or detached) to respective planes in hw
-	 * - as part of crtc_commit, scaler will be either attached or detached
-	 *   to crtc in hw
-	 */
-
-	/* fail if required scalers > available scalers */
-	if (num_scalers_need > intel_crtc->num_scalers){
-		drm_dbg_kms(&dev_priv->drm,
-			    "Too many scaling requests %d > %d\n",
-			    num_scalers_need, intel_crtc->num_scalers);
-		return -EINVAL;
-	}
-
-	/* walkthrough scaler_users bits and start assigning scalers */
-	for (i = 0; i < sizeof(scaler_state->scaler_users) * 8; i++) {
-		int *scaler_id;
-		const char *name;
-		int idx;
-
-		/* skip if scaler not required */
-		if (!(scaler_state->scaler_users & (1 << i)))
-			continue;
-
-		if (i == SKL_CRTC_INDEX) {
-			name = "CRTC";
-			idx = intel_crtc->base.base.id;
-
-			/* panel fitter case: assign as a crtc scaler */
-			scaler_id = &scaler_state->scaler_id;
-		} else {
-			name = "PLANE";
-
-			/* plane scaler case: assign as a plane scaler */
-			/* find the plane that set the bit as scaler_user */
-			plane = drm_state->planes[i].ptr;
-
-			/*
-			 * to enable/disable hq mode, add planes that are using scaler
-			 * into this transaction
-			 */
-			if (!plane) {
-				struct drm_plane_state *state;
-
-				/*
-				 * GLK+ scalers don't have a HQ mode so it
-				 * isn't necessary to change between HQ and dyn mode
-				 * on those platforms.
-				 */
-				if (DISPLAY_VER(dev_priv) >= 10)
-					continue;
-
-				plane = drm_plane_from_index(&dev_priv->drm, i);
-				state = drm_atomic_get_plane_state(drm_state, plane);
-				if (IS_ERR(state)) {
-					drm_dbg_kms(&dev_priv->drm,
-						    "Failed to add [PLANE:%d] to drm_state\n",
-						    plane->base.id);
-					return PTR_ERR(state);
-				}
-			}
-
-			intel_plane = to_intel_plane(plane);
-			idx = plane->base.id;
-
-			/* plane on different crtc cannot be a scaler user of this crtc */
-			if (drm_WARN_ON(&dev_priv->drm,
-					intel_plane->pipe != intel_crtc->pipe))
-				continue;
-
-			plane_state = intel_atomic_get_new_plane_state(intel_state,
-								       intel_plane);
-			scaler_id = &plane_state->scaler_id;
-		}
-
-		intel_atomic_setup_scaler(scaler_state, num_scalers_need,
-					  intel_crtc, name, idx,
-					  plane_state, scaler_id);
-	}
-
-	return 0;
-}
-
 struct drm_atomic_state *
 intel_atomic_state_alloc(struct drm_device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_atomic.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_atomic.h
@@ -54,8 +54,4 @@
 intel_atomic_get_crtc_state(struct drm_atomic_state *state,
 			    struct intel_crtc *crtc);
 
-int intel_atomic_setup_scalers(struct drm_i915_private *dev_priv,
-			       struct intel_crtc *intel_crtc,
-			       struct intel_crtc_state *crtc_state);
-
 #endif /* __INTEL_ATOMIC_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_backlight.c
@@ -0,0 +1,1776 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright © 2021 Intel Corporation
+ */
+
+#include <linux/kernel.h>
+#include <linux/pwm.h>
+
+#include "intel_backlight.h"
+#include "intel_connector.h"
+#include "intel_de.h"
+#include "intel_display_types.h"
+#include "intel_dp_aux_backlight.h"
+#include "intel_dsi_dcs_backlight.h"
+#include "intel_panel.h"
+
+/**
+ * scale - scale values from one range to another
+ * @source_val: value in range [@source_min..@source_max]
+ * @source_min: minimum legal value for @source_val
+ * @source_max: maximum legal value for @source_val
+ * @target_min: corresponding target value for @source_min
+ * @target_max: corresponding target value for @source_max
+ *
+ * Return @source_val in range [@source_min..@source_max] scaled to range
+ * [@target_min..@target_max].
+ */
+static u32 scale(u32 source_val,
+		 u32 source_min, u32 source_max,
+		 u32 target_min, u32 target_max)
+{
+	u64 target_val;
+
+	WARN_ON(source_min > source_max);
+	WARN_ON(target_min > target_max);
+
+	/* defensive */
+	source_val = clamp(source_val, source_min, source_max);
+
+	/* avoid overflows */
+	target_val = mul_u32_u32(source_val - source_min,
+				 target_max - target_min);
+	target_val = DIV_ROUND_CLOSEST_ULL(target_val, source_max - source_min);
+	target_val += target_min;
+
+	return target_val;
+}
+
+/*
+ * Scale user_level in range [0..user_max] to [0..hw_max], clamping the result
+ * to [hw_min..hw_max].
+ */
+static u32 clamp_user_to_hw(struct intel_connector *connector,
+			    u32 user_level, u32 user_max)
+{
+	struct intel_panel *panel = &connector->panel;
+	u32 hw_level;
+
+	hw_level = scale(user_level, 0, user_max, 0, panel->backlight.max);
+	hw_level = clamp(hw_level, panel->backlight.min, panel->backlight.max);
+
+	return hw_level;
+}
+
+/* Scale hw_level in range [hw_min..hw_max] to [0..user_max]. */
+static u32 scale_hw_to_user(struct intel_connector *connector,
+			    u32 hw_level, u32 user_max)
+{
+	struct intel_panel *panel = &connector->panel;
+
+	return scale(hw_level, panel->backlight.min, panel->backlight.max,
+		     0, user_max);
+}
+
+u32 intel_panel_invert_pwm_level(struct intel_connector *connector, u32 val)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	drm_WARN_ON(&dev_priv->drm, panel->backlight.pwm_level_max == 0);
+
+	if (dev_priv->params.invert_brightness < 0)
+		return val;
+
+	if (dev_priv->params.invert_brightness > 0 ||
+	    dev_priv->quirks & QUIRK_INVERT_BRIGHTNESS) {
+		return panel->backlight.pwm_level_max - val + panel->backlight.pwm_level_min;
+	}
+
+	return val;
+}
+
+void intel_panel_set_pwm_level(const struct drm_connector_state *conn_state, u32 val)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *i915 = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	drm_dbg_kms(&i915->drm, "set backlight PWM = %d\n", val);
+	panel->backlight.pwm_funcs->set(conn_state, val);
+}
+
+u32 intel_panel_backlight_level_to_pwm(struct intel_connector *connector, u32 val)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	drm_WARN_ON_ONCE(&dev_priv->drm,
+			 panel->backlight.max == 0 || panel->backlight.pwm_level_max == 0);
+
+	val = scale(val, panel->backlight.min, panel->backlight.max,
+		    panel->backlight.pwm_level_min, panel->backlight.pwm_level_max);
+
+	return intel_panel_invert_pwm_level(connector, val);
+}
+
+u32 intel_panel_backlight_level_from_pwm(struct intel_connector *connector, u32 val)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	drm_WARN_ON_ONCE(&dev_priv->drm,
+			 panel->backlight.max == 0 || panel->backlight.pwm_level_max == 0);
+
+	if (dev_priv->params.invert_brightness > 0 ||
+	    (dev_priv->params.invert_brightness == 0 && dev_priv->quirks & QUIRK_INVERT_BRIGHTNESS))
+		val = panel->backlight.pwm_level_max - (val - panel->backlight.pwm_level_min);
+
+	return scale(val, panel->backlight.pwm_level_min, panel->backlight.pwm_level_max,
+		     panel->backlight.min, panel->backlight.max);
+}
+
+static u32 lpt_get_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	return intel_de_read(dev_priv, BLC_PWM_PCH_CTL2) & BACKLIGHT_DUTY_CYCLE_MASK;
+}
+
+static u32 pch_get_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	return intel_de_read(dev_priv, BLC_PWM_CPU_CTL) & BACKLIGHT_DUTY_CYCLE_MASK;
+}
+
+static u32 i9xx_get_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 val;
+
+	val = intel_de_read(dev_priv, BLC_PWM_CTL) & BACKLIGHT_DUTY_CYCLE_MASK;
+	if (DISPLAY_VER(dev_priv) < 4)
+		val >>= 1;
+
+	if (panel->backlight.combination_mode) {
+		u8 lbpc;
+
+		pci_read_config_byte(to_pci_dev(dev_priv->drm.dev), LBPC, &lbpc);
+		val *= lbpc;
+	}
+
+	return val;
+}
+
+static u32 vlv_get_backlight(struct intel_connector *connector, enum pipe pipe)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	if (drm_WARN_ON(&dev_priv->drm, pipe != PIPE_A && pipe != PIPE_B))
+		return 0;
+
+	return intel_de_read(dev_priv, VLV_BLC_PWM_CTL(pipe)) & BACKLIGHT_DUTY_CYCLE_MASK;
+}
+
+static u32 bxt_get_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	return intel_de_read(dev_priv,
+			     BXT_BLC_PWM_DUTY(panel->backlight.controller));
+}
+
+static u32 ext_pwm_get_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct intel_panel *panel = &connector->panel;
+	struct pwm_state state;
+
+	pwm_get_state(panel->backlight.pwm, &state);
+	return pwm_get_relative_duty_cycle(&state, 100);
+}
+
+static void lpt_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	u32 val = intel_de_read(dev_priv, BLC_PWM_PCH_CTL2) & ~BACKLIGHT_DUTY_CYCLE_MASK;
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL2, val | level);
+}
+
+static void pch_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	u32 tmp;
+
+	tmp = intel_de_read(dev_priv, BLC_PWM_CPU_CTL) & ~BACKLIGHT_DUTY_CYCLE_MASK;
+	intel_de_write(dev_priv, BLC_PWM_CPU_CTL, tmp | level);
+}
+
+static void i9xx_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 tmp, mask;
+
+	drm_WARN_ON(&dev_priv->drm, panel->backlight.pwm_level_max == 0);
+
+	if (panel->backlight.combination_mode) {
+		u8 lbpc;
+
+		lbpc = level * 0xfe / panel->backlight.pwm_level_max + 1;
+		level /= lbpc;
+		pci_write_config_byte(to_pci_dev(dev_priv->drm.dev), LBPC, lbpc);
+	}
+
+	if (DISPLAY_VER(dev_priv) == 4) {
+		mask = BACKLIGHT_DUTY_CYCLE_MASK;
+	} else {
+		level <<= 1;
+		mask = BACKLIGHT_DUTY_CYCLE_MASK_PNV;
+	}
+
+	tmp = intel_de_read(dev_priv, BLC_PWM_CTL) & ~mask;
+	intel_de_write(dev_priv, BLC_PWM_CTL, tmp | level);
+}
+
+static void vlv_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	enum pipe pipe = to_intel_crtc(conn_state->crtc)->pipe;
+	u32 tmp;
+
+	tmp = intel_de_read(dev_priv, VLV_BLC_PWM_CTL(pipe)) & ~BACKLIGHT_DUTY_CYCLE_MASK;
+	intel_de_write(dev_priv, VLV_BLC_PWM_CTL(pipe), tmp | level);
+}
+
+static void bxt_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	intel_de_write(dev_priv,
+		       BXT_BLC_PWM_DUTY(panel->backlight.controller), level);
+}
+
+static void ext_pwm_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_panel *panel = &to_intel_connector(conn_state->connector)->panel;
+
+	pwm_set_relative_duty_cycle(&panel->backlight.pwm_state, level, 100);
+	pwm_apply_state(panel->backlight.pwm, &panel->backlight.pwm_state);
+}
+
+static void
+intel_panel_actually_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *i915 = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	drm_dbg_kms(&i915->drm, "set backlight level = %d\n", level);
+
+	panel->backlight.funcs->set(conn_state, level);
+}
+
+/* set backlight brightness to level in range [0..max], assuming hw min is
+ * respected.
+ */
+void intel_panel_set_backlight_acpi(const struct drm_connector_state *conn_state,
+				    u32 user_level, u32 user_max)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 hw_level;
+
+	/*
+	 * Lack of crtc may occur during driver init because
+	 * connection_mutex isn't held across the entire backlight
+	 * setup + modeset readout, and the BIOS can issue the
+	 * requests at any time.
+	 */
+	if (!panel->backlight.present || !conn_state->crtc)
+		return;
+
+	mutex_lock(&dev_priv->backlight_lock);
+
+	drm_WARN_ON(&dev_priv->drm, panel->backlight.max == 0);
+
+	hw_level = clamp_user_to_hw(connector, user_level, user_max);
+	panel->backlight.level = hw_level;
+
+	if (panel->backlight.device)
+		panel->backlight.device->props.brightness =
+			scale_hw_to_user(connector,
+					 panel->backlight.level,
+					 panel->backlight.device->props.max_brightness);
+
+	if (panel->backlight.enabled)
+		intel_panel_actually_set_backlight(conn_state, hw_level);
+
+	mutex_unlock(&dev_priv->backlight_lock);
+}
+
+static void lpt_disable_backlight(const struct drm_connector_state *old_conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	u32 tmp;
+
+	intel_panel_set_pwm_level(old_conn_state, level);
+
+	/*
+	 * Although we don't support or enable CPU PWM with LPT/SPT based
+	 * systems, it may have been enabled prior to loading the
+	 * driver. Disable to avoid warnings on LCPLL disable.
+	 *
+	 * This needs rework if we need to add support for CPU PWM on PCH split
+	 * platforms.
+	 */
+	tmp = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
+	if (tmp & BLM_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "cpu backlight was enabled, disabling\n");
+		intel_de_write(dev_priv, BLC_PWM_CPU_CTL2,
+			       tmp & ~BLM_PWM_ENABLE);
+	}
+
+	tmp = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, tmp & ~BLM_PCH_PWM_ENABLE);
+}
+
+static void pch_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	u32 tmp;
+
+	intel_panel_set_pwm_level(old_conn_state, val);
+
+	tmp = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
+	intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, tmp & ~BLM_PWM_ENABLE);
+
+	tmp = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, tmp & ~BLM_PCH_PWM_ENABLE);
+}
+
+static void i9xx_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
+{
+	intel_panel_set_pwm_level(old_conn_state, val);
+}
+
+static void i965_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
+{
+	struct drm_i915_private *dev_priv = to_i915(old_conn_state->connector->dev);
+	u32 tmp;
+
+	intel_panel_set_pwm_level(old_conn_state, val);
+
+	tmp = intel_de_read(dev_priv, BLC_PWM_CTL2);
+	intel_de_write(dev_priv, BLC_PWM_CTL2, tmp & ~BLM_PWM_ENABLE);
+}
+
+static void vlv_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	enum pipe pipe = to_intel_crtc(old_conn_state->crtc)->pipe;
+	u32 tmp;
+
+	intel_panel_set_pwm_level(old_conn_state, val);
+
+	tmp = intel_de_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
+	intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe),
+		       tmp & ~BLM_PWM_ENABLE);
+}
+
+static void bxt_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 tmp;
+
+	intel_panel_set_pwm_level(old_conn_state, val);
+
+	tmp = intel_de_read(dev_priv,
+			    BXT_BLC_PWM_CTL(panel->backlight.controller));
+	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
+		       tmp & ~BXT_BLC_PWM_ENABLE);
+
+	if (panel->backlight.controller == 1) {
+		val = intel_de_read(dev_priv, UTIL_PIN_CTL);
+		val &= ~UTIL_PIN_ENABLE;
+		intel_de_write(dev_priv, UTIL_PIN_CTL, val);
+	}
+}
+
+static void cnp_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 tmp;
+
+	intel_panel_set_pwm_level(old_conn_state, val);
+
+	tmp = intel_de_read(dev_priv,
+			    BXT_BLC_PWM_CTL(panel->backlight.controller));
+	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
+		       tmp & ~BXT_BLC_PWM_ENABLE);
+}
+
+static void ext_pwm_disable_backlight(const struct drm_connector_state *old_conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct intel_panel *panel = &connector->panel;
+
+	panel->backlight.pwm_state.enabled = false;
+	pwm_apply_state(panel->backlight.pwm, &panel->backlight.pwm_state);
+}
+
+void intel_panel_disable_backlight(const struct drm_connector_state *old_conn_state)
+{
+	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	if (!panel->backlight.present)
+		return;
+
+	/*
+	 * Do not disable backlight on the vga_switcheroo path. When switching
+	 * away from i915, the other client may depend on i915 to handle the
+	 * backlight. This will leave the backlight on unnecessarily when
+	 * another client is not activated.
+	 */
+	if (dev_priv->drm.switch_power_state == DRM_SWITCH_POWER_CHANGING) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "Skipping backlight disable on vga switch\n");
+		return;
+	}
+
+	mutex_lock(&dev_priv->backlight_lock);
+
+	if (panel->backlight.device)
+		panel->backlight.device->props.power = FB_BLANK_POWERDOWN;
+	panel->backlight.enabled = false;
+	panel->backlight.funcs->disable(old_conn_state, 0);
+
+	mutex_unlock(&dev_priv->backlight_lock);
+}
+
+static void lpt_enable_backlight(const struct intel_crtc_state *crtc_state,
+				 const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 pch_ctl1, pch_ctl2, schicken;
+
+	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
+	if (pch_ctl1 & BLM_PCH_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "pch backlight already enabled\n");
+		pch_ctl1 &= ~BLM_PCH_PWM_ENABLE;
+		intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
+	}
+
+	if (HAS_PCH_LPT(dev_priv)) {
+		schicken = intel_de_read(dev_priv, SOUTH_CHICKEN2);
+		if (panel->backlight.alternate_pwm_increment)
+			schicken |= LPT_PWM_GRANULARITY;
+		else
+			schicken &= ~LPT_PWM_GRANULARITY;
+		intel_de_write(dev_priv, SOUTH_CHICKEN2, schicken);
+	} else {
+		schicken = intel_de_read(dev_priv, SOUTH_CHICKEN1);
+		if (panel->backlight.alternate_pwm_increment)
+			schicken |= SPT_PWM_GRANULARITY;
+		else
+			schicken &= ~SPT_PWM_GRANULARITY;
+		intel_de_write(dev_priv, SOUTH_CHICKEN1, schicken);
+	}
+
+	pch_ctl2 = panel->backlight.pwm_level_max << 16;
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL2, pch_ctl2);
+
+	pch_ctl1 = 0;
+	if (panel->backlight.active_low_pwm)
+		pch_ctl1 |= BLM_PCH_POLARITY;
+
+	/* After LPT, override is the default. */
+	if (HAS_PCH_LPT(dev_priv))
+		pch_ctl1 |= BLM_PCH_OVERRIDE_ENABLE;
+
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
+	intel_de_posting_read(dev_priv, BLC_PWM_PCH_CTL1);
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1,
+		       pch_ctl1 | BLM_PCH_PWM_ENABLE);
+
+	/* This won't stick until the above enable. */
+	intel_panel_set_pwm_level(conn_state, level);
+}
+
+static void pch_enable_backlight(const struct intel_crtc_state *crtc_state,
+				 const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
+	u32 cpu_ctl2, pch_ctl1, pch_ctl2;
+
+	cpu_ctl2 = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
+	if (cpu_ctl2 & BLM_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "cpu backlight already enabled\n");
+		cpu_ctl2 &= ~BLM_PWM_ENABLE;
+		intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, cpu_ctl2);
+	}
+
+	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
+	if (pch_ctl1 & BLM_PCH_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "pch backlight already enabled\n");
+		pch_ctl1 &= ~BLM_PCH_PWM_ENABLE;
+		intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
+	}
+
+	if (cpu_transcoder == TRANSCODER_EDP)
+		cpu_ctl2 = BLM_TRANSCODER_EDP;
+	else
+		cpu_ctl2 = BLM_PIPE(cpu_transcoder);
+	intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, cpu_ctl2);
+	intel_de_posting_read(dev_priv, BLC_PWM_CPU_CTL2);
+	intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, cpu_ctl2 | BLM_PWM_ENABLE);
+
+	/* This won't stick until the above enable. */
+	intel_panel_set_pwm_level(conn_state, level);
+
+	pch_ctl2 = panel->backlight.pwm_level_max << 16;
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL2, pch_ctl2);
+
+	pch_ctl1 = 0;
+	if (panel->backlight.active_low_pwm)
+		pch_ctl1 |= BLM_PCH_POLARITY;
+
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
+	intel_de_posting_read(dev_priv, BLC_PWM_PCH_CTL1);
+	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1,
+		       pch_ctl1 | BLM_PCH_PWM_ENABLE);
+}
+
+static void i9xx_enable_backlight(const struct intel_crtc_state *crtc_state,
+				  const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 ctl, freq;
+
+	ctl = intel_de_read(dev_priv, BLC_PWM_CTL);
+	if (ctl & BACKLIGHT_DUTY_CYCLE_MASK_PNV) {
+		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
+		intel_de_write(dev_priv, BLC_PWM_CTL, 0);
+	}
+
+	freq = panel->backlight.pwm_level_max;
+	if (panel->backlight.combination_mode)
+		freq /= 0xff;
+
+	ctl = freq << 17;
+	if (panel->backlight.combination_mode)
+		ctl |= BLM_LEGACY_MODE;
+	if (IS_PINEVIEW(dev_priv) && panel->backlight.active_low_pwm)
+		ctl |= BLM_POLARITY_PNV;
+
+	intel_de_write(dev_priv, BLC_PWM_CTL, ctl);
+	intel_de_posting_read(dev_priv, BLC_PWM_CTL);
+
+	/* XXX: combine this into above write? */
+	intel_panel_set_pwm_level(conn_state, level);
+
+	/*
+	 * Needed to enable backlight on some 855gm models. BLC_HIST_CTL is
+	 * 855gm only, but checking for gen2 is safe, as 855gm is the only gen2
+	 * that has backlight.
+	 */
+	if (DISPLAY_VER(dev_priv) == 2)
+		intel_de_write(dev_priv, BLC_HIST_CTL, BLM_HISTOGRAM_ENABLE);
+}
+
+static void i965_enable_backlight(const struct intel_crtc_state *crtc_state,
+				  const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	enum pipe pipe = to_intel_crtc(conn_state->crtc)->pipe;
+	u32 ctl, ctl2, freq;
+
+	ctl2 = intel_de_read(dev_priv, BLC_PWM_CTL2);
+	if (ctl2 & BLM_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
+		ctl2 &= ~BLM_PWM_ENABLE;
+		intel_de_write(dev_priv, BLC_PWM_CTL2, ctl2);
+	}
+
+	freq = panel->backlight.pwm_level_max;
+	if (panel->backlight.combination_mode)
+		freq /= 0xff;
+
+	ctl = freq << 16;
+	intel_de_write(dev_priv, BLC_PWM_CTL, ctl);
+
+	ctl2 = BLM_PIPE(pipe);
+	if (panel->backlight.combination_mode)
+		ctl2 |= BLM_COMBINATION_MODE;
+	if (panel->backlight.active_low_pwm)
+		ctl2 |= BLM_POLARITY_I965;
+	intel_de_write(dev_priv, BLC_PWM_CTL2, ctl2);
+	intel_de_posting_read(dev_priv, BLC_PWM_CTL2);
+	intel_de_write(dev_priv, BLC_PWM_CTL2, ctl2 | BLM_PWM_ENABLE);
+
+	intel_panel_set_pwm_level(conn_state, level);
+}
+
+static void vlv_enable_backlight(const struct intel_crtc_state *crtc_state,
+				 const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	enum pipe pipe = to_intel_crtc(crtc_state->uapi.crtc)->pipe;
+	u32 ctl, ctl2;
+
+	ctl2 = intel_de_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
+	if (ctl2 & BLM_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
+		ctl2 &= ~BLM_PWM_ENABLE;
+		intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe), ctl2);
+	}
+
+	ctl = panel->backlight.pwm_level_max << 16;
+	intel_de_write(dev_priv, VLV_BLC_PWM_CTL(pipe), ctl);
+
+	/* XXX: combine this into above write? */
+	intel_panel_set_pwm_level(conn_state, level);
+
+	ctl2 = 0;
+	if (panel->backlight.active_low_pwm)
+		ctl2 |= BLM_POLARITY_I965;
+	intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe), ctl2);
+	intel_de_posting_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
+	intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe),
+		       ctl2 | BLM_PWM_ENABLE);
+}
+
+static void bxt_enable_backlight(const struct intel_crtc_state *crtc_state,
+				 const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	enum pipe pipe = to_intel_crtc(crtc_state->uapi.crtc)->pipe;
+	u32 pwm_ctl, val;
+
+	/* Controller 1 uses the utility pin. */
+	if (panel->backlight.controller == 1) {
+		val = intel_de_read(dev_priv, UTIL_PIN_CTL);
+		if (val & UTIL_PIN_ENABLE) {
+			drm_dbg_kms(&dev_priv->drm,
+				    "util pin already enabled\n");
+			val &= ~UTIL_PIN_ENABLE;
+			intel_de_write(dev_priv, UTIL_PIN_CTL, val);
+		}
+
+		val = 0;
+		if (panel->backlight.util_pin_active_low)
+			val |= UTIL_PIN_POLARITY;
+		intel_de_write(dev_priv, UTIL_PIN_CTL,
+			       val | UTIL_PIN_PIPE(pipe) | UTIL_PIN_MODE_PWM | UTIL_PIN_ENABLE);
+	}
+
+	pwm_ctl = intel_de_read(dev_priv,
+				BXT_BLC_PWM_CTL(panel->backlight.controller));
+	if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
+		pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
+		intel_de_write(dev_priv,
+			       BXT_BLC_PWM_CTL(panel->backlight.controller),
+			       pwm_ctl);
+	}
+
+	intel_de_write(dev_priv,
+		       BXT_BLC_PWM_FREQ(panel->backlight.controller),
+		       panel->backlight.pwm_level_max);
+
+	intel_panel_set_pwm_level(conn_state, level);
+
+	pwm_ctl = 0;
+	if (panel->backlight.active_low_pwm)
+		pwm_ctl |= BXT_BLC_PWM_POLARITY;
+
+	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
+		       pwm_ctl);
+	intel_de_posting_read(dev_priv,
+			      BXT_BLC_PWM_CTL(panel->backlight.controller));
+	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
+		       pwm_ctl | BXT_BLC_PWM_ENABLE);
+}
+
+static void cnp_enable_backlight(const struct intel_crtc_state *crtc_state,
+				 const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 pwm_ctl;
+
+	pwm_ctl = intel_de_read(dev_priv,
+				BXT_BLC_PWM_CTL(panel->backlight.controller));
+	if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
+		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
+		pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
+		intel_de_write(dev_priv,
+			       BXT_BLC_PWM_CTL(panel->backlight.controller),
+			       pwm_ctl);
+	}
+
+	intel_de_write(dev_priv,
+		       BXT_BLC_PWM_FREQ(panel->backlight.controller),
+		       panel->backlight.pwm_level_max);
+
+	intel_panel_set_pwm_level(conn_state, level);
+
+	pwm_ctl = 0;
+	if (panel->backlight.active_low_pwm)
+		pwm_ctl |= BXT_BLC_PWM_POLARITY;
+
+	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
+		       pwm_ctl);
+	intel_de_posting_read(dev_priv,
+			      BXT_BLC_PWM_CTL(panel->backlight.controller));
+	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
+		       pwm_ctl | BXT_BLC_PWM_ENABLE);
+}
+
+static void ext_pwm_enable_backlight(const struct intel_crtc_state *crtc_state,
+				     const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct intel_panel *panel = &connector->panel;
+
+	pwm_set_relative_duty_cycle(&panel->backlight.pwm_state, level, 100);
+	panel->backlight.pwm_state.enabled = true;
+	pwm_apply_state(panel->backlight.pwm, &panel->backlight.pwm_state);
+}
+
+static void __intel_panel_enable_backlight(const struct intel_crtc_state *crtc_state,
+					   const struct drm_connector_state *conn_state)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct intel_panel *panel = &connector->panel;
+
+	WARN_ON(panel->backlight.max == 0);
+
+	if (panel->backlight.level <= panel->backlight.min) {
+		panel->backlight.level = panel->backlight.max;
+		if (panel->backlight.device)
+			panel->backlight.device->props.brightness =
+				scale_hw_to_user(connector,
+						 panel->backlight.level,
+						 panel->backlight.device->props.max_brightness);
+	}
+
+	panel->backlight.funcs->enable(crtc_state, conn_state, panel->backlight.level);
+	panel->backlight.enabled = true;
+	if (panel->backlight.device)
+		panel->backlight.device->props.power = FB_BLANK_UNBLANK;
+}
+
+void intel_panel_enable_backlight(const struct intel_crtc_state *crtc_state,
+				  const struct drm_connector_state *conn_state)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	enum pipe pipe = to_intel_crtc(crtc_state->uapi.crtc)->pipe;
+
+	if (!panel->backlight.present)
+		return;
+
+	drm_dbg_kms(&dev_priv->drm, "pipe %c\n", pipe_name(pipe));
+
+	mutex_lock(&dev_priv->backlight_lock);
+
+	__intel_panel_enable_backlight(crtc_state, conn_state);
+
+	mutex_unlock(&dev_priv->backlight_lock);
+}
+
+#if IS_ENABLED(CONFIG_BACKLIGHT_CLASS_DEVICE)
+static u32 intel_panel_get_backlight(struct intel_connector *connector)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 val = 0;
+
+	mutex_lock(&dev_priv->backlight_lock);
+
+	if (panel->backlight.enabled)
+		val = panel->backlight.funcs->get(connector, intel_connector_get_pipe(connector));
+
+	mutex_unlock(&dev_priv->backlight_lock);
+
+	drm_dbg_kms(&dev_priv->drm, "get backlight PWM = %d\n", val);
+	return val;
+}
+
+/* Scale user_level in range [0..user_max] to [hw_min..hw_max]. */
+static u32 scale_user_to_hw(struct intel_connector *connector,
+			    u32 user_level, u32 user_max)
+{
+	struct intel_panel *panel = &connector->panel;
+
+	return scale(user_level, 0, user_max,
+		     panel->backlight.min, panel->backlight.max);
+}
+
+/* set backlight brightness to level in range [0..max], scaling wrt hw min */
+static void intel_panel_set_backlight(const struct drm_connector_state *conn_state,
+				      u32 user_level, u32 user_max)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 hw_level;
+
+	if (!panel->backlight.present)
+		return;
+
+	mutex_lock(&dev_priv->backlight_lock);
+
+	drm_WARN_ON(&dev_priv->drm, panel->backlight.max == 0);
+
+	hw_level = scale_user_to_hw(connector, user_level, user_max);
+	panel->backlight.level = hw_level;
+
+	if (panel->backlight.enabled)
+		intel_panel_actually_set_backlight(conn_state, hw_level);
+
+	mutex_unlock(&dev_priv->backlight_lock);
+}
+
+static int intel_backlight_device_update_status(struct backlight_device *bd)
+{
+	struct intel_connector *connector = bl_get_data(bd);
+	struct intel_panel *panel = &connector->panel;
+	struct drm_device *dev = connector->base.dev;
+
+	drm_modeset_lock(&dev->mode_config.connection_mutex, NULL);
+	DRM_DEBUG_KMS("updating intel_backlight, brightness=%d/%d\n",
+		      bd->props.brightness, bd->props.max_brightness);
+	intel_panel_set_backlight(connector->base.state, bd->props.brightness,
+				  bd->props.max_brightness);
+
+	/*
+	 * Allow flipping bl_power as a sub-state of enabled. Sadly the
+	 * backlight class device does not make it easy to differentiate
+	 * between callbacks for brightness and bl_power, so our backlight_power
+	 * callback needs to take this into account.
+	 */
+	if (panel->backlight.enabled) {
+		if (panel->backlight.power) {
+			bool enable = bd->props.power == FB_BLANK_UNBLANK &&
+				bd->props.brightness != 0;
+			panel->backlight.power(connector, enable);
+		}
+	} else {
+		bd->props.power = FB_BLANK_POWERDOWN;
+	}
+
+	drm_modeset_unlock(&dev->mode_config.connection_mutex);
+	return 0;
+}
+
+static int intel_backlight_device_get_brightness(struct backlight_device *bd)
+{
+	struct intel_connector *connector = bl_get_data(bd);
+	struct drm_device *dev = connector->base.dev;
+	struct drm_i915_private *dev_priv = to_i915(dev);
+	intel_wakeref_t wakeref;
+	int ret = 0;
+
+	with_intel_runtime_pm(&dev_priv->runtime_pm, wakeref) {
+		u32 hw_level;
+
+		drm_modeset_lock(&dev->mode_config.connection_mutex, NULL);
+
+		hw_level = intel_panel_get_backlight(connector);
+		ret = scale_hw_to_user(connector,
+				       hw_level, bd->props.max_brightness);
+
+		drm_modeset_unlock(&dev->mode_config.connection_mutex);
+	}
+
+	return ret;
+}
+
+static const struct backlight_ops intel_backlight_device_ops = {
+	.update_status = intel_backlight_device_update_status,
+	.get_brightness = intel_backlight_device_get_brightness,
+};
+
+int intel_backlight_device_register(struct intel_connector *connector)
+{
+	struct drm_i915_private *i915 = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	struct backlight_properties props;
+	struct backlight_device *bd;
+	const char *name;
+	int ret = 0;
+
+	if (WARN_ON(panel->backlight.device))
+		return -ENODEV;
+
+	if (!panel->backlight.present)
+		return 0;
+
+	WARN_ON(panel->backlight.max == 0);
+
+	memset(&props, 0, sizeof(props));
+	props.type = BACKLIGHT_RAW;
+
+	/*
+	 * Note: Everything should work even if the backlight device max
+	 * presented to the userspace is arbitrarily chosen.
+	 */
+	props.max_brightness = panel->backlight.max;
+	props.brightness = scale_hw_to_user(connector,
+					    panel->backlight.level,
+					    props.max_brightness);
+
+	if (panel->backlight.enabled)
+		props.power = FB_BLANK_UNBLANK;
+	else
+		props.power = FB_BLANK_POWERDOWN;
+
+	name = kstrdup("intel_backlight", GFP_KERNEL);
+	if (!name)
+		return -ENOMEM;
+
+	bd = backlight_device_get_by_name(name);
+	if (bd) {
+		put_device(&bd->dev);
+		/*
+		 * Using the same name independent of the drm device or connector
+		 * prevents registration of multiple backlight devices in the
+		 * driver. However, we need to use the default name for backward
+		 * compatibility. Use unique names for subsequent backlight devices as a
+		 * fallback when the default name already exists.
+		 */
+		kfree(name);
+		name = kasprintf(GFP_KERNEL, "card%d-%s-backlight",
+				 i915->drm.primary->index, connector->base.name);
+		if (!name)
+			return -ENOMEM;
+	}
+	bd = backlight_device_register(name, connector->base.kdev, connector,
+				       &intel_backlight_device_ops, &props);
+
+	if (IS_ERR(bd)) {
+		drm_err(&i915->drm,
+			"[CONNECTOR:%d:%s] backlight device %s register failed: %ld\n",
+			connector->base.base.id, connector->base.name, name, PTR_ERR(bd));
+		ret = PTR_ERR(bd);
+		goto out;
+	}
+
+	panel->backlight.device = bd;
+
+	drm_dbg_kms(&i915->drm,
+		    "[CONNECTOR:%d:%s] backlight device %s registered\n",
+		    connector->base.base.id, connector->base.name, name);
+
+out:
+	kfree(name);
+
+	return ret;
+}
+
+void intel_backlight_device_unregister(struct intel_connector *connector)
+{
+	struct intel_panel *panel = &connector->panel;
+
+	if (panel->backlight.device) {
+		backlight_device_unregister(panel->backlight.device);
+		panel->backlight.device = NULL;
+	}
+}
+#endif /* CONFIG_BACKLIGHT_CLASS_DEVICE */
+
+/*
+ * CNP: PWM clock frequency is 19.2 MHz or 24 MHz.
+ *      PWM increment = 1
+ */
+static u32 cnp_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	return DIV_ROUND_CLOSEST(KHz(RUNTIME_INFO(dev_priv)->rawclk_freq),
+				 pwm_freq_hz);
+}
+
+/*
+ * BXT: PWM clock frequency = 19.2 MHz.
+ */
+static u32 bxt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	return DIV_ROUND_CLOSEST(KHz(19200), pwm_freq_hz);
+}
+
+/*
+ * SPT: This value represents the period of the PWM stream in clock periods
+ * multiplied by 16 (default increment) or 128 (alternate increment selected in
+ * SCHICKEN_1 bit 0). PWM clock is 24 MHz.
+ */
+static u32 spt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct intel_panel *panel = &connector->panel;
+	u32 mul;
+
+	if (panel->backlight.alternate_pwm_increment)
+		mul = 128;
+	else
+		mul = 16;
+
+	return DIV_ROUND_CLOSEST(MHz(24), pwm_freq_hz * mul);
+}
+
+/*
+ * LPT: This value represents the period of the PWM stream in clock periods
+ * multiplied by 128 (default increment) or 16 (alternate increment, selected in
+ * LPT SOUTH_CHICKEN2 register bit 5).
+ */
+static u32 lpt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 mul, clock;
+
+	if (panel->backlight.alternate_pwm_increment)
+		mul = 16;
+	else
+		mul = 128;
+
+	if (HAS_PCH_LPT_H(dev_priv))
+		clock = MHz(135); /* LPT:H */
+	else
+		clock = MHz(24); /* LPT:LP */
+
+	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * mul);
+}
+
+/*
+ * ILK/SNB/IVB: This value represents the period of the PWM stream in PCH
+ * display raw clocks multiplied by 128.
+ */
+static u32 pch_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	return DIV_ROUND_CLOSEST(KHz(RUNTIME_INFO(dev_priv)->rawclk_freq),
+				 pwm_freq_hz * 128);
+}
+
+/*
+ * Gen2: This field determines the number of time base events (display core
+ * clock frequency/32) in total for a complete cycle of modulated backlight
+ * control.
+ *
+ * Gen3: A time base event equals the display core clock ([DevPNV] HRAW clock)
+ * divided by 32.
+ */
+static u32 i9xx_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	int clock;
+
+	if (IS_PINEVIEW(dev_priv))
+		clock = KHz(RUNTIME_INFO(dev_priv)->rawclk_freq);
+	else
+		clock = KHz(dev_priv->cdclk.hw.cdclk);
+
+	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * 32);
+}
+
+/*
+ * Gen4: This value represents the period of the PWM stream in display core
+ * clocks ([DevCTG] HRAW clocks) multiplied by 128.
+ *
+ */
+static u32 i965_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	int clock;
+
+	if (IS_G4X(dev_priv))
+		clock = KHz(RUNTIME_INFO(dev_priv)->rawclk_freq);
+	else
+		clock = KHz(dev_priv->cdclk.hw.cdclk);
+
+	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * 128);
+}
+
+/*
+ * VLV: This value represents the period of the PWM stream in display core
+ * clocks ([DevCTG] 200MHz HRAW clocks) multiplied by 128 or 25MHz S0IX clocks
+ * multiplied by 16. CHV uses a 19.2MHz S0IX clock.
+ */
+static u32 vlv_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	int mul, clock;
+
+	if ((intel_de_read(dev_priv, CBR1_VLV) & CBR_PWM_CLOCK_MUX_SELECT) == 0) {
+		if (IS_CHERRYVIEW(dev_priv))
+			clock = KHz(19200);
+		else
+			clock = MHz(25);
+		mul = 16;
+	} else {
+		clock = KHz(RUNTIME_INFO(dev_priv)->rawclk_freq);
+		mul = 128;
+	}
+
+	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * mul);
+}
+
+static u16 get_vbt_pwm_freq(struct drm_i915_private *dev_priv)
+{
+	u16 pwm_freq_hz = dev_priv->vbt.backlight.pwm_freq_hz;
+
+	if (pwm_freq_hz) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "VBT defined backlight frequency %u Hz\n",
+			    pwm_freq_hz);
+	} else {
+		pwm_freq_hz = 200;
+		drm_dbg_kms(&dev_priv->drm,
+			    "default backlight frequency %u Hz\n",
+			    pwm_freq_hz);
+	}
+
+	return pwm_freq_hz;
+}
+
+static u32 get_backlight_max_vbt(struct intel_connector *connector)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u16 pwm_freq_hz = get_vbt_pwm_freq(dev_priv);
+	u32 pwm;
+
+	if (!panel->backlight.pwm_funcs->hz_to_pwm) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "backlight frequency conversion not supported\n");
+		return 0;
+	}
+
+	pwm = panel->backlight.pwm_funcs->hz_to_pwm(connector, pwm_freq_hz);
+	if (!pwm) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "backlight frequency conversion failed\n");
+		return 0;
+	}
+
+	return pwm;
+}
+
+/*
+ * Note: The setup hooks can't assume pipe is set!
+ */
+static u32 get_backlight_min_vbt(struct intel_connector *connector)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	int min;
+
+	drm_WARN_ON(&dev_priv->drm, panel->backlight.pwm_level_max == 0);
+
+	/*
+	 * XXX: If the vbt value is 255, it makes min equal to max, which leads
+	 * to problems. There are such machines out there. Either our
+	 * interpretation is wrong or the vbt has bogus data. Or both. Safeguard
+	 * against this by letting the minimum be at most (arbitrarily chosen)
+	 * 25% of the max.
+	 */
+	min = clamp_t(int, dev_priv->vbt.backlight.min_brightness, 0, 64);
+	if (min != dev_priv->vbt.backlight.min_brightness) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "clamping VBT min backlight %d/255 to %d/255\n",
+			    dev_priv->vbt.backlight.min_brightness, min);
+	}
+
+	/* vbt value is a coefficient in range [0..255] */
+	return scale(min, 0, 255, 0, panel->backlight.pwm_level_max);
+}
+
+static int lpt_setup_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 cpu_ctl2, pch_ctl1, pch_ctl2, val;
+	bool alt, cpu_mode;
+
+	if (HAS_PCH_LPT(dev_priv))
+		alt = intel_de_read(dev_priv, SOUTH_CHICKEN2) & LPT_PWM_GRANULARITY;
+	else
+		alt = intel_de_read(dev_priv, SOUTH_CHICKEN1) & SPT_PWM_GRANULARITY;
+	panel->backlight.alternate_pwm_increment = alt;
+
+	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
+	panel->backlight.active_low_pwm = pch_ctl1 & BLM_PCH_POLARITY;
+
+	pch_ctl2 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL2);
+	panel->backlight.pwm_level_max = pch_ctl2 >> 16;
+
+	cpu_ctl2 = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
+
+	if (!panel->backlight.pwm_level_max)
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	panel->backlight.pwm_enabled = pch_ctl1 & BLM_PCH_PWM_ENABLE;
+
+	cpu_mode = panel->backlight.pwm_enabled && HAS_PCH_LPT(dev_priv) &&
+		   !(pch_ctl1 & BLM_PCH_OVERRIDE_ENABLE) &&
+		   (cpu_ctl2 & BLM_PWM_ENABLE);
+
+	if (cpu_mode) {
+		val = pch_get_backlight(connector, unused);
+
+		drm_dbg_kms(&dev_priv->drm,
+			    "CPU backlight register was enabled, switching to PCH override\n");
+
+		/* Write converted CPU PWM value to PCH override register */
+		lpt_set_backlight(connector->base.state, val);
+		intel_de_write(dev_priv, BLC_PWM_PCH_CTL1,
+			       pch_ctl1 | BLM_PCH_OVERRIDE_ENABLE);
+
+		intel_de_write(dev_priv, BLC_PWM_CPU_CTL2,
+			       cpu_ctl2 & ~BLM_PWM_ENABLE);
+	}
+
+	return 0;
+}
+
+static int pch_setup_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 cpu_ctl2, pch_ctl1, pch_ctl2;
+
+	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
+	panel->backlight.active_low_pwm = pch_ctl1 & BLM_PCH_POLARITY;
+
+	pch_ctl2 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL2);
+	panel->backlight.pwm_level_max = pch_ctl2 >> 16;
+
+	if (!panel->backlight.pwm_level_max)
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	cpu_ctl2 = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
+	panel->backlight.pwm_enabled = (cpu_ctl2 & BLM_PWM_ENABLE) &&
+		(pch_ctl1 & BLM_PCH_PWM_ENABLE);
+
+	return 0;
+}
+
+static int i9xx_setup_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 ctl, val;
+
+	ctl = intel_de_read(dev_priv, BLC_PWM_CTL);
+
+	if (DISPLAY_VER(dev_priv) == 2 || IS_I915GM(dev_priv) || IS_I945GM(dev_priv))
+		panel->backlight.combination_mode = ctl & BLM_LEGACY_MODE;
+
+	if (IS_PINEVIEW(dev_priv))
+		panel->backlight.active_low_pwm = ctl & BLM_POLARITY_PNV;
+
+	panel->backlight.pwm_level_max = ctl >> 17;
+
+	if (!panel->backlight.pwm_level_max) {
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+		panel->backlight.pwm_level_max >>= 1;
+	}
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	if (panel->backlight.combination_mode)
+		panel->backlight.pwm_level_max *= 0xff;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	val = i9xx_get_backlight(connector, unused);
+	val = intel_panel_invert_pwm_level(connector, val);
+	val = clamp(val, panel->backlight.pwm_level_min, panel->backlight.pwm_level_max);
+
+	panel->backlight.pwm_enabled = val != 0;
+
+	return 0;
+}
+
+static int i965_setup_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 ctl, ctl2;
+
+	ctl2 = intel_de_read(dev_priv, BLC_PWM_CTL2);
+	panel->backlight.combination_mode = ctl2 & BLM_COMBINATION_MODE;
+	panel->backlight.active_low_pwm = ctl2 & BLM_POLARITY_I965;
+
+	ctl = intel_de_read(dev_priv, BLC_PWM_CTL);
+	panel->backlight.pwm_level_max = ctl >> 16;
+
+	if (!panel->backlight.pwm_level_max)
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	if (panel->backlight.combination_mode)
+		panel->backlight.pwm_level_max *= 0xff;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	panel->backlight.pwm_enabled = ctl2 & BLM_PWM_ENABLE;
+
+	return 0;
+}
+
+static int vlv_setup_backlight(struct intel_connector *connector, enum pipe pipe)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 ctl, ctl2;
+
+	if (drm_WARN_ON(&dev_priv->drm, pipe != PIPE_A && pipe != PIPE_B))
+		return -ENODEV;
+
+	ctl2 = intel_de_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
+	panel->backlight.active_low_pwm = ctl2 & BLM_POLARITY_I965;
+
+	ctl = intel_de_read(dev_priv, VLV_BLC_PWM_CTL(pipe));
+	panel->backlight.pwm_level_max = ctl >> 16;
+
+	if (!panel->backlight.pwm_level_max)
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	panel->backlight.pwm_enabled = ctl2 & BLM_PWM_ENABLE;
+
+	return 0;
+}
+
+static int
+bxt_setup_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 pwm_ctl, val;
+
+	panel->backlight.controller = dev_priv->vbt.backlight.controller;
+
+	pwm_ctl = intel_de_read(dev_priv,
+				BXT_BLC_PWM_CTL(panel->backlight.controller));
+
+	/* Controller 1 uses the utility pin. */
+	if (panel->backlight.controller == 1) {
+		val = intel_de_read(dev_priv, UTIL_PIN_CTL);
+		panel->backlight.util_pin_active_low =
+					val & UTIL_PIN_POLARITY;
+	}
+
+	panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
+	panel->backlight.pwm_level_max =
+		intel_de_read(dev_priv, BXT_BLC_PWM_FREQ(panel->backlight.controller));
+
+	if (!panel->backlight.pwm_level_max)
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	panel->backlight.pwm_enabled = pwm_ctl & BXT_BLC_PWM_ENABLE;
+
+	return 0;
+}
+
+static int
+cnp_setup_backlight(struct intel_connector *connector, enum pipe unused)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u32 pwm_ctl;
+
+	/*
+	 * CNP has the BXT implementation of backlight, but with only one
+	 * controller. TODO: ICP has multiple controllers but we only use
+	 * controller 0 for now.
+	 */
+	panel->backlight.controller = 0;
+
+	pwm_ctl = intel_de_read(dev_priv,
+				BXT_BLC_PWM_CTL(panel->backlight.controller));
+
+	panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
+	panel->backlight.pwm_level_max =
+		intel_de_read(dev_priv, BXT_BLC_PWM_FREQ(panel->backlight.controller));
+
+	if (!panel->backlight.pwm_level_max)
+		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
+
+	if (!panel->backlight.pwm_level_max)
+		return -ENODEV;
+
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	panel->backlight.pwm_enabled = pwm_ctl & BXT_BLC_PWM_ENABLE;
+
+	return 0;
+}
+
+static int ext_pwm_setup_backlight(struct intel_connector *connector,
+				   enum pipe pipe)
+{
+	struct drm_device *dev = connector->base.dev;
+	struct drm_i915_private *dev_priv = to_i915(dev);
+	struct intel_panel *panel = &connector->panel;
+	const char *desc;
+	u32 level;
+
+	/* Get the right PWM chip for DSI backlight according to VBT */
+	if (dev_priv->vbt.dsi.config->pwm_blc == PPS_BLC_PMIC) {
+		panel->backlight.pwm = pwm_get(dev->dev, "pwm_pmic_backlight");
+		desc = "PMIC";
+	} else {
+		panel->backlight.pwm = pwm_get(dev->dev, "pwm_soc_backlight");
+		desc = "SoC";
+	}
+
+	if (IS_ERR(panel->backlight.pwm)) {
+		drm_err(&dev_priv->drm, "Failed to get the %s PWM chip\n",
+			desc);
+		panel->backlight.pwm = NULL;
+		return -ENODEV;
+	}
+
+	panel->backlight.pwm_level_max = 100; /* 100% */
+	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
+
+	if (pwm_is_enabled(panel->backlight.pwm)) {
+		/* PWM is already enabled, use existing settings */
+		pwm_get_state(panel->backlight.pwm, &panel->backlight.pwm_state);
+
+		level = pwm_get_relative_duty_cycle(&panel->backlight.pwm_state,
+						    100);
+		level = intel_panel_invert_pwm_level(connector, level);
+		panel->backlight.pwm_enabled = true;
+
+		drm_dbg_kms(&dev_priv->drm, "PWM already enabled at freq %ld, VBT freq %d, level %d\n",
+			    NSEC_PER_SEC / (unsigned long)panel->backlight.pwm_state.period,
+			    get_vbt_pwm_freq(dev_priv), level);
+	} else {
+		/* Set period from VBT frequency, leave other settings at 0. */
+		panel->backlight.pwm_state.period =
+			NSEC_PER_SEC / get_vbt_pwm_freq(dev_priv);
+	}
+
+	drm_info(&dev_priv->drm, "Using %s PWM for LCD backlight control\n",
+		 desc);
+	return 0;
+}
+
+static void intel_pwm_set_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct intel_panel *panel = &connector->panel;
+
+	panel->backlight.pwm_funcs->set(conn_state,
+				       intel_panel_invert_pwm_level(connector, level));
+}
+
+static u32 intel_pwm_get_backlight(struct intel_connector *connector, enum pipe pipe)
+{
+	struct intel_panel *panel = &connector->panel;
+
+	return intel_panel_invert_pwm_level(connector,
+					    panel->backlight.pwm_funcs->get(connector, pipe));
+}
+
+static void intel_pwm_enable_backlight(const struct intel_crtc_state *crtc_state,
+				       const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct intel_panel *panel = &connector->panel;
+
+	panel->backlight.pwm_funcs->enable(crtc_state, conn_state,
+					   intel_panel_invert_pwm_level(connector, level));
+}
+
+static void intel_pwm_disable_backlight(const struct drm_connector_state *conn_state, u32 level)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct intel_panel *panel = &connector->panel;
+
+	panel->backlight.pwm_funcs->disable(conn_state,
+					    intel_panel_invert_pwm_level(connector, level));
+}
+
+static int intel_pwm_setup_backlight(struct intel_connector *connector, enum pipe pipe)
+{
+	struct intel_panel *panel = &connector->panel;
+	int ret = panel->backlight.pwm_funcs->setup(connector, pipe);
+
+	if (ret < 0)
+		return ret;
+
+	panel->backlight.min = panel->backlight.pwm_level_min;
+	panel->backlight.max = panel->backlight.pwm_level_max;
+	panel->backlight.level = intel_pwm_get_backlight(connector, pipe);
+	panel->backlight.enabled = panel->backlight.pwm_enabled;
+
+	return 0;
+}
+
+void intel_panel_update_backlight(struct intel_atomic_state *state,
+				  struct intel_encoder *encoder,
+				  const struct intel_crtc_state *crtc_state,
+				  const struct drm_connector_state *conn_state)
+{
+	struct intel_connector *connector = to_intel_connector(conn_state->connector);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+
+	if (!panel->backlight.present)
+		return;
+
+	mutex_lock(&dev_priv->backlight_lock);
+	if (!panel->backlight.enabled)
+		__intel_panel_enable_backlight(crtc_state, conn_state);
+
+	mutex_unlock(&dev_priv->backlight_lock);
+}
+
+int intel_panel_setup_backlight(struct drm_connector *connector, enum pipe pipe)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->dev);
+	struct intel_connector *intel_connector = to_intel_connector(connector);
+	struct intel_panel *panel = &intel_connector->panel;
+	int ret;
+
+	if (!dev_priv->vbt.backlight.present) {
+		if (dev_priv->quirks & QUIRK_BACKLIGHT_PRESENT) {
+			drm_dbg_kms(&dev_priv->drm,
+				    "no backlight present per VBT, but present per quirk\n");
+		} else {
+			drm_dbg_kms(&dev_priv->drm,
+				    "no backlight present per VBT\n");
+			return 0;
+		}
+	}
+
+	/* ensure intel_panel has been initialized first */
+	if (drm_WARN_ON(&dev_priv->drm, !panel->backlight.funcs))
+		return -ENODEV;
+
+	/* set level and max in panel struct */
+	mutex_lock(&dev_priv->backlight_lock);
+	ret = panel->backlight.funcs->setup(intel_connector, pipe);
+	mutex_unlock(&dev_priv->backlight_lock);
+
+	if (ret) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "failed to setup backlight for connector %s\n",
+			    connector->name);
+		return ret;
+	}
+
+	panel->backlight.present = true;
+
+	drm_dbg_kms(&dev_priv->drm,
+		    "Connector %s backlight initialized, %s, brightness %u/%u\n",
+		    connector->name,
+		    enableddisabled(panel->backlight.enabled),
+		    panel->backlight.level, panel->backlight.max);
+
+	return 0;
+}
+
+void intel_panel_destroy_backlight(struct intel_panel *panel)
+{
+	/* dispose of the pwm */
+	if (panel->backlight.pwm)
+		pwm_put(panel->backlight.pwm);
+
+	panel->backlight.present = false;
+}
+
+static const struct intel_panel_bl_funcs bxt_pwm_funcs = {
+	.setup = bxt_setup_backlight,
+	.enable = bxt_enable_backlight,
+	.disable = bxt_disable_backlight,
+	.set = bxt_set_backlight,
+	.get = bxt_get_backlight,
+	.hz_to_pwm = bxt_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs cnp_pwm_funcs = {
+	.setup = cnp_setup_backlight,
+	.enable = cnp_enable_backlight,
+	.disable = cnp_disable_backlight,
+	.set = bxt_set_backlight,
+	.get = bxt_get_backlight,
+	.hz_to_pwm = cnp_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs lpt_pwm_funcs = {
+	.setup = lpt_setup_backlight,
+	.enable = lpt_enable_backlight,
+	.disable = lpt_disable_backlight,
+	.set = lpt_set_backlight,
+	.get = lpt_get_backlight,
+	.hz_to_pwm = lpt_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs spt_pwm_funcs = {
+	.setup = lpt_setup_backlight,
+	.enable = lpt_enable_backlight,
+	.disable = lpt_disable_backlight,
+	.set = lpt_set_backlight,
+	.get = lpt_get_backlight,
+	.hz_to_pwm = spt_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs pch_pwm_funcs = {
+	.setup = pch_setup_backlight,
+	.enable = pch_enable_backlight,
+	.disable = pch_disable_backlight,
+	.set = pch_set_backlight,
+	.get = pch_get_backlight,
+	.hz_to_pwm = pch_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs ext_pwm_funcs = {
+	.setup = ext_pwm_setup_backlight,
+	.enable = ext_pwm_enable_backlight,
+	.disable = ext_pwm_disable_backlight,
+	.set = ext_pwm_set_backlight,
+	.get = ext_pwm_get_backlight,
+};
+
+static const struct intel_panel_bl_funcs vlv_pwm_funcs = {
+	.setup = vlv_setup_backlight,
+	.enable = vlv_enable_backlight,
+	.disable = vlv_disable_backlight,
+	.set = vlv_set_backlight,
+	.get = vlv_get_backlight,
+	.hz_to_pwm = vlv_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs i965_pwm_funcs = {
+	.setup = i965_setup_backlight,
+	.enable = i965_enable_backlight,
+	.disable = i965_disable_backlight,
+	.set = i9xx_set_backlight,
+	.get = i9xx_get_backlight,
+	.hz_to_pwm = i965_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs i9xx_pwm_funcs = {
+	.setup = i9xx_setup_backlight,
+	.enable = i9xx_enable_backlight,
+	.disable = i9xx_disable_backlight,
+	.set = i9xx_set_backlight,
+	.get = i9xx_get_backlight,
+	.hz_to_pwm = i9xx_hz_to_pwm,
+};
+
+static const struct intel_panel_bl_funcs pwm_bl_funcs = {
+	.setup = intel_pwm_setup_backlight,
+	.enable = intel_pwm_enable_backlight,
+	.disable = intel_pwm_disable_backlight,
+	.set = intel_pwm_set_backlight,
+	.get = intel_pwm_get_backlight,
+};
+
+/* Set up chip specific backlight functions */
+void
+intel_panel_init_backlight_funcs(struct intel_panel *panel)
+{
+	struct intel_connector *connector =
+		container_of(panel, struct intel_connector, panel);
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+
+	if (connector->base.connector_type == DRM_MODE_CONNECTOR_DSI &&
+	    intel_dsi_dcs_init_backlight_funcs(connector) == 0)
+		return;
+
+	if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) {
+		panel->backlight.pwm_funcs = &bxt_pwm_funcs;
+	} else if (INTEL_PCH_TYPE(dev_priv) >= PCH_CNP) {
+		panel->backlight.pwm_funcs = &cnp_pwm_funcs;
+	} else if (INTEL_PCH_TYPE(dev_priv) >= PCH_LPT) {
+		if (HAS_PCH_LPT(dev_priv))
+			panel->backlight.pwm_funcs = &lpt_pwm_funcs;
+		else
+			panel->backlight.pwm_funcs = &spt_pwm_funcs;
+	} else if (HAS_PCH_SPLIT(dev_priv)) {
+		panel->backlight.pwm_funcs = &pch_pwm_funcs;
+	} else if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) {
+		if (connector->base.connector_type == DRM_MODE_CONNECTOR_DSI) {
+			panel->backlight.pwm_funcs = &ext_pwm_funcs;
+		} else {
+			panel->backlight.pwm_funcs = &vlv_pwm_funcs;
+		}
+	} else if (DISPLAY_VER(dev_priv) == 4) {
+		panel->backlight.pwm_funcs = &i965_pwm_funcs;
+	} else {
+		panel->backlight.pwm_funcs = &i9xx_pwm_funcs;
+	}
+
+	if (connector->base.connector_type == DRM_MODE_CONNECTOR_eDP &&
+	    intel_dp_aux_init_backlight_funcs(connector) == 0)
+		return;
+
+	/* We're using a standard PWM backlight interface */
+	panel->backlight.funcs = &pwm_bl_funcs;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_backlight.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_backlight.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright © 2021 Intel Corporation
+ */
+
+#ifndef __INTEL_BACKLIGHT_H__
+#define __INTEL_BACKLIGHT_H__
+
+#include <linux/types.h>
+
+struct drm_connector;
+struct drm_connector_state;
+struct intel_atomic_state;
+struct intel_connector;
+struct intel_crtc_state;
+struct intel_encoder;
+struct intel_panel;
+enum pipe;
+
+void intel_panel_init_backlight_funcs(struct intel_panel *panel);
+void intel_panel_destroy_backlight(struct intel_panel *panel);
+void intel_panel_set_backlight_acpi(const struct drm_connector_state *conn_state,
+				    u32 level, u32 max);
+int intel_panel_setup_backlight(struct drm_connector *connector,
+				enum pipe pipe);
+void intel_panel_enable_backlight(const struct intel_crtc_state *crtc_state,
+				  const struct drm_connector_state *conn_state);
+void intel_panel_update_backlight(struct intel_atomic_state *state,
+				  struct intel_encoder *encoder,
+				  const struct intel_crtc_state *crtc_state,
+				  const struct drm_connector_state *conn_state);
+void intel_panel_disable_backlight(const struct drm_connector_state *old_conn_state);
+void intel_panel_set_pwm_level(const struct drm_connector_state *conn_state, u32 level);
+u32 intel_panel_invert_pwm_level(struct intel_connector *connector, u32 level);
+u32 intel_panel_backlight_level_to_pwm(struct intel_connector *connector, u32 level);
+u32 intel_panel_backlight_level_from_pwm(struct intel_connector *connector, u32 val);
+
+#if IS_ENABLED(CONFIG_BACKLIGHT_CLASS_DEVICE)
+int intel_backlight_device_register(struct intel_connector *connector);
+void intel_backlight_device_unregister(struct intel_connector *connector);
+#else /* CONFIG_BACKLIGHT_CLASS_DEVICE */
+static inline int intel_backlight_device_register(struct intel_connector *connector)
+{
+	return 0;
+}
+static inline void intel_backlight_device_unregister(struct intel_connector *connector)
+{
+}
+#endif /* CONFIG_BACKLIGHT_CLASS_DEVICE */
+
+#endif /* __INTEL_BACKLIGHT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_bios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_bios.c
@@ -1692,6 +1692,39 @@
 	return 0;
 }
 
+static u8 dvo_port_type(u8 dvo_port)
+{
+	switch (dvo_port) {
+	case DVO_PORT_HDMIA:
+	case DVO_PORT_HDMIB:
+	case DVO_PORT_HDMIC:
+	case DVO_PORT_HDMID:
+	case DVO_PORT_HDMIE:
+	case DVO_PORT_HDMIF:
+	case DVO_PORT_HDMIG:
+	case DVO_PORT_HDMIH:
+	case DVO_PORT_HDMII:
+		return DVO_PORT_HDMIA;
+	case DVO_PORT_DPA:
+	case DVO_PORT_DPB:
+	case DVO_PORT_DPC:
+	case DVO_PORT_DPD:
+	case DVO_PORT_DPE:
+	case DVO_PORT_DPF:
+	case DVO_PORT_DPG:
+	case DVO_PORT_DPH:
+	case DVO_PORT_DPI:
+		return DVO_PORT_DPA;
+	case DVO_PORT_MIPIA:
+	case DVO_PORT_MIPIB:
+	case DVO_PORT_MIPIC:
+	case DVO_PORT_MIPID:
+		return DVO_PORT_MIPIA;
+	default:
+		return dvo_port;
+	}
+}
+
 static enum port __dvo_port_to_port(int n_ports, int n_dvo,
 				    const int port_mapping[][3], u8 dvo_port)
 {
@@ -1787,6 +1820,22 @@
 					  dvo_port);
 }
 
+static enum port
+dsi_dvo_port_to_port(struct drm_i915_private *i915, u8 dvo_port)
+{
+	switch (dvo_port) {
+	case DVO_PORT_MIPIA:
+		return PORT_A;
+	case DVO_PORT_MIPIC:
+		if (DISPLAY_VER(i915) >= 11)
+			return PORT_B;
+		else
+			return PORT_C;
+	default:
+		return PORT_NONE;
+	}
+}
+
 static int parse_bdb_230_dp_max_link_rate(const int vbt_max_link_rate)
 {
 	switch (vbt_max_link_rate) {
@@ -1980,6 +2029,15 @@
 		case HDMI_MAX_DATA_RATE_PLATFORM:
 			max_tmds_clock = 0;
 			break;
+		case HDMI_MAX_DATA_RATE_594:
+			max_tmds_clock = 594000;
+			break;
+		case HDMI_MAX_DATA_RATE_340:
+			max_tmds_clock = 340000;
+			break;
+		case HDMI_MAX_DATA_RATE_300:
+			max_tmds_clock = 300000;
+			break;
 		case HDMI_MAX_DATA_RATE_297:
 			max_tmds_clock = 297000;
 			break;
@@ -2622,35 +2680,17 @@
 	return false;
 }
 
-static bool child_dev_is_dp_dual_mode(const struct child_device_config *child,
-				      enum port port)
+static bool child_dev_is_dp_dual_mode(const struct child_device_config *child)
 {
-	static const struct {
-		u16 dp, hdmi;
-	} port_mapping[] = {
-		/*
-		 * Buggy VBTs may declare DP ports as having
-		 * HDMI type dvo_port :( So let's check both.
-		 */
-		[PORT_B] = { DVO_PORT_DPB, DVO_PORT_HDMIB, },
-		[PORT_C] = { DVO_PORT_DPC, DVO_PORT_HDMIC, },
-		[PORT_D] = { DVO_PORT_DPD, DVO_PORT_HDMID, },
-		[PORT_E] = { DVO_PORT_DPE, DVO_PORT_HDMIE, },
-		[PORT_F] = { DVO_PORT_DPF, DVO_PORT_HDMIF, },
-	};
-
-	if (port == PORT_A || port >= ARRAY_SIZE(port_mapping))
-		return false;
-
 	if ((child->device_type & DEVICE_TYPE_DP_DUAL_MODE_BITS) !=
 	    (DEVICE_TYPE_DP_DUAL_MODE & DEVICE_TYPE_DP_DUAL_MODE_BITS))
 		return false;
 
-	if (child->dvo_port == port_mapping[port].dp)
+	if (dvo_port_type(child->dvo_port) == DVO_PORT_DPA)
 		return true;
 
 	/* Only accept a HDMI dvo_port as DP++ if it has an AUX channel */
-	if (child->dvo_port == port_mapping[port].hdmi &&
+	if (dvo_port_type(child->dvo_port) == DVO_PORT_HDMIA &&
 	    child->aux_channel != 0)
 		return true;
 
@@ -2660,10 +2700,36 @@
 bool intel_bios_is_port_dp_dual_mode(struct drm_i915_private *i915,
 				     enum port port)
 {
+	static const struct {
+		u16 dp, hdmi;
+	} port_mapping[] = {
+		/*
+		 * Buggy VBTs may declare DP ports as having
+		 * HDMI type dvo_port :( So let's check both.
+		 */
+		[PORT_B] = { DVO_PORT_DPB, DVO_PORT_HDMIB, },
+		[PORT_C] = { DVO_PORT_DPC, DVO_PORT_HDMIC, },
+		[PORT_D] = { DVO_PORT_DPD, DVO_PORT_HDMID, },
+		[PORT_E] = { DVO_PORT_DPE, DVO_PORT_HDMIE, },
+		[PORT_F] = { DVO_PORT_DPF, DVO_PORT_HDMIF, },
+	};
 	const struct intel_bios_encoder_data *devdata;
 
+	if (HAS_DDI(i915)) {
+		const struct intel_bios_encoder_data *devdata;
+
+		devdata = intel_bios_encoder_data_lookup(i915, port);
+
+		return devdata && child_dev_is_dp_dual_mode(&devdata->child);
+	}
+
+	if (port == PORT_A || port >= ARRAY_SIZE(port_mapping))
+		return false;
+
 	list_for_each_entry(devdata, &i915->vbt.display_devices, node) {
-		if (child_dev_is_dp_dual_mode(&devdata->child, port))
+		if ((devdata->child.dvo_port == port_mapping[port].dp ||
+		     devdata->child.dvo_port == port_mapping[port].hdmi) &&
+		    child_dev_is_dp_dual_mode(&devdata->child))
 			return true;
 	}
 
@@ -2692,19 +2758,16 @@
 
 		dvo_port = child->dvo_port;
 
-		if (dvo_port == DVO_PORT_MIPIA ||
-		    (dvo_port == DVO_PORT_MIPIB && DISPLAY_VER(i915) >= 11) ||
-		    (dvo_port == DVO_PORT_MIPIC && DISPLAY_VER(i915) < 11)) {
-			if (port)
-				*port = dvo_port - DVO_PORT_MIPIA;
-			return true;
-		} else if (dvo_port == DVO_PORT_MIPIB ||
-			   dvo_port == DVO_PORT_MIPIC ||
-			   dvo_port == DVO_PORT_MIPID) {
+		if (dsi_dvo_port_to_port(i915, dvo_port) == PORT_NONE) {
 			drm_dbg_kms(&i915->drm,
 				    "VBT has unsupported DSI port %c\n",
 				    port_name(dvo_port - DVO_PORT_MIPIA));
+			continue;
 		}
+
+		if (port)
+			*port = dsi_dvo_port_to_port(i915, dvo_port);
+		return true;
 	}
 
 	return false;
@@ -2789,7 +2852,7 @@
 		if (!(child->device_type & DEVICE_TYPE_MIPI_OUTPUT))
 			continue;
 
-		if (child->dvo_port - DVO_PORT_MIPIA == encoder->port) {
+		if (dsi_dvo_port_to_port(i915, child->dvo_port) == encoder->port) {
 			if (!devdata->dsc)
 				return false;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_bw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_bw.c
@@ -681,6 +681,7 @@
 	unsigned int max_bw_point = 0, max_bw = 0;
 	unsigned int num_qgv_points = dev_priv->max_bw[0].num_qgv_points;
 	unsigned int num_psf_gv_points = dev_priv->max_bw[0].num_psf_gv_points;
+	bool changed = false;
 	u32 mask = 0;
 
 	/* FIXME earlier gens need some checks too */
@@ -724,6 +725,8 @@
 		new_bw_state->data_rate[crtc->pipe] = new_data_rate;
 		new_bw_state->num_active_planes[crtc->pipe] = new_active_planes;
 
+		changed = true;
+
 		drm_dbg_kms(&dev_priv->drm,
 			    "pipe %c data rate %u num active planes %u\n",
 			    pipe_name(crtc->pipe),
@@ -731,7 +734,19 @@
 			    new_bw_state->num_active_planes[crtc->pipe]);
 	}
 
-	if (!new_bw_state)
+	old_bw_state = intel_atomic_get_old_bw_state(state);
+	new_bw_state = intel_atomic_get_new_bw_state(state);
+
+	if (new_bw_state &&
+	    intel_can_enable_sagv(dev_priv, old_bw_state) !=
+	    intel_can_enable_sagv(dev_priv, new_bw_state))
+		changed = true;
+
+	/*
+	 * If none of our inputs (data rates, number of active
+	 * planes, SAGV yes/no) changed then nothing to do here.
+	 */
+	if (!changed)
 		return 0;
 
 	ret = intel_atomic_lock_global_state(&new_bw_state->base);
@@ -804,7 +819,8 @@
 	 * cause.
 	 */
 	if (!intel_can_enable_sagv(dev_priv, new_bw_state)) {
-		allowed_points = BIT(max_bw_point);
+		allowed_points &= ADLS_PSF_PT_MASK;
+		allowed_points |= BIT(max_bw_point);
 		drm_dbg_kms(&dev_priv->drm, "No SAGV, using single QGV point %d\n",
 			    max_bw_point);
 	}
@@ -814,7 +830,6 @@
 	 */
 	new_bw_state->qgv_points_mask = ~allowed_points & mask;
 
-	old_bw_state = intel_atomic_get_old_bw_state(state);
 	/*
 	 * If the actual mask had changed we need to make sure that
 	 * the commits are serialized(in case this is a nomodeset, nonblocking)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_bw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_bw.h
@@ -30,19 +30,19 @@
 	 */
 	u8 pipe_sagv_reject;
 
+	/* bitmask of active pipes */
+	u8 active_pipes;
+
 	/*
 	 * Current QGV points mask, which restricts
 	 * some particular SAGV states, not to confuse
 	 * with pipe_sagv_mask.
 	 */
-	u8 qgv_points_mask;
+	u16 qgv_points_mask;
 
 	unsigned int data_rate[I915_MAX_PIPES];
 	u8 num_active_planes[I915_MAX_PIPES];
 
-	/* bitmask of active pipes */
-	u8 active_pipes;
-
 	int min_cdclk;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_cdclk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_cdclk.c
@@ -1269,7 +1269,7 @@
 	{ .refclk = 24000, .cdclk = 192000, .divider = 2, .ratio = 16 },
 	{ .refclk = 24000, .cdclk = 312000, .divider = 2, .ratio = 26 },
 	{ .refclk = 24000, .cdclk = 552000, .divider = 2, .ratio = 46 },
-	{ .refclk = 24400, .cdclk = 648000, .divider = 2, .ratio = 54 },
+	{ .refclk = 24000, .cdclk = 648000, .divider = 2, .ratio = 54 },
 
 	{ .refclk = 38400, .cdclk = 179200, .divider = 3, .ratio = 14 },
 	{ .refclk = 38400, .cdclk = 192000, .divider = 2, .ratio = 10 },
@@ -2000,7 +2000,7 @@
 				 &new_cdclk_state->actual))
 		return;
 
-	if (pipe == INVALID_PIPE ||
+	if (new_cdclk_state->disable_pipes ||
 	    old_cdclk_state->actual.cdclk <= new_cdclk_state->actual.cdclk) {
 		drm_WARN_ON(&dev_priv->drm, !new_cdclk_state->base.changed);
 
@@ -2029,7 +2029,7 @@
 				 &new_cdclk_state->actual))
 		return;
 
-	if (pipe != INVALID_PIPE &&
+	if (!new_cdclk_state->disable_pipes &&
 	    old_cdclk_state->actual.cdclk > new_cdclk_state->actual.cdclk) {
 		drm_WARN_ON(&dev_priv->drm, !new_cdclk_state->base.changed);
 
@@ -2456,6 +2456,7 @@
 		return NULL;
 
 	cdclk_state->pipe = INVALID_PIPE;
+	cdclk_state->disable_pipes = false;
 
 	return &cdclk_state->base;
 }
@@ -2575,6 +2576,8 @@
 		if (ret)
 			return ret;
 
+		new_cdclk_state->disable_pipes = true;
+
 		drm_dbg_kms(&dev_priv->drm,
 			    "Modeset required for cdclk change\n");
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_cdclk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_cdclk.h
@@ -52,6 +52,9 @@
 
 	/* bitmask of active pipes */
 	u8 active_pipes;
+
+	/* update cdclk with pipes disabled */
+	bool disable_pipes;
 };
 
 int intel_crtc_compute_min_cdclk(const struct intel_crtc_state *crtc_state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_color.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_color.c
@@ -550,8 +550,8 @@
 	lut = blob->data;
 
 	for (i = 0; i < 256; i++)
-		intel_de_write(dev_priv, PALETTE(pipe, i),
-			       i9xx_lut_8(&lut[i]));
+		intel_de_write_fw(dev_priv, PALETTE(pipe, i),
+				  i9xx_lut_8(&lut[i]));
 }
 
 static void i9xx_load_luts(const struct intel_crtc_state *crtc_state)
@@ -574,15 +574,15 @@
 	enum pipe pipe = crtc->pipe;
 
 	for (i = 0; i < lut_size - 1; i++) {
-		intel_de_write(dev_priv, PALETTE(pipe, 2 * i + 0),
-			       i965_lut_10p6_ldw(&lut[i]));
-		intel_de_write(dev_priv, PALETTE(pipe, 2 * i + 1),
-			       i965_lut_10p6_udw(&lut[i]));
+		intel_de_write_fw(dev_priv, PALETTE(pipe, 2 * i + 0),
+				  i965_lut_10p6_ldw(&lut[i]));
+		intel_de_write_fw(dev_priv, PALETTE(pipe, 2 * i + 1),
+				  i965_lut_10p6_udw(&lut[i]));
 	}
 
-	intel_de_write(dev_priv, PIPEGCMAX(pipe, 0), lut[i].red);
-	intel_de_write(dev_priv, PIPEGCMAX(pipe, 1), lut[i].green);
-	intel_de_write(dev_priv, PIPEGCMAX(pipe, 2), lut[i].blue);
+	intel_de_write_fw(dev_priv, PIPEGCMAX(pipe, 0), lut[i].red);
+	intel_de_write_fw(dev_priv, PIPEGCMAX(pipe, 1), lut[i].green);
+	intel_de_write_fw(dev_priv, PIPEGCMAX(pipe, 2), lut[i].blue);
 }
 
 static void i965_load_luts(const struct intel_crtc_state *crtc_state)
@@ -616,8 +616,8 @@
 	lut = blob->data;
 
 	for (i = 0; i < 256; i++)
-		intel_de_write(dev_priv, LGC_PALETTE(pipe, i),
-			       i9xx_lut_8(&lut[i]));
+		intel_de_write_fw(dev_priv, LGC_PALETTE(pipe, i),
+				  i9xx_lut_8(&lut[i]));
 }
 
 static void ilk_load_lut_10(struct intel_crtc *crtc,
@@ -629,8 +629,8 @@
 	enum pipe pipe = crtc->pipe;
 
 	for (i = 0; i < lut_size; i++)
-		intel_de_write(dev_priv, PREC_PALETTE(pipe, i),
-			       ilk_lut_10(&lut[i]));
+		intel_de_write_fw(dev_priv, PREC_PALETTE(pipe, i),
+				  ilk_lut_10(&lut[i]));
 }
 
 static void ilk_load_luts(const struct intel_crtc_state *crtc_state)
@@ -679,16 +679,16 @@
 		const struct drm_color_lut *entry =
 			&lut[i * (lut_size - 1) / (hw_lut_size - 1)];
 
-		intel_de_write(dev_priv, PREC_PAL_INDEX(pipe), prec_index++);
-		intel_de_write(dev_priv, PREC_PAL_DATA(pipe),
-			       ilk_lut_10(entry));
+		intel_de_write_fw(dev_priv, PREC_PAL_INDEX(pipe), prec_index++);
+		intel_de_write_fw(dev_priv, PREC_PAL_DATA(pipe),
+				  ilk_lut_10(entry));
 	}
 
 	/*
 	 * Reset the index, otherwise it prevents the legacy palette to be
 	 * written properly.
 	 */
-	intel_de_write(dev_priv, PREC_PAL_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PREC_PAL_INDEX(pipe), 0);
 }
 
 /* On BDW+ the index auto increment mode actually works */
@@ -702,23 +702,23 @@
 	int i, lut_size = drm_color_lut_size(blob);
 	enum pipe pipe = crtc->pipe;
 
-	intel_de_write(dev_priv, PREC_PAL_INDEX(pipe),
-		       prec_index | PAL_PREC_AUTO_INCREMENT);
+	intel_de_write_fw(dev_priv, PREC_PAL_INDEX(pipe),
+			  prec_index | PAL_PREC_AUTO_INCREMENT);
 
 	for (i = 0; i < hw_lut_size; i++) {
 		/* We discard half the user entries in split gamma mode */
 		const struct drm_color_lut *entry =
 			&lut[i * (lut_size - 1) / (hw_lut_size - 1)];
 
-		intel_de_write(dev_priv, PREC_PAL_DATA(pipe),
-			       ilk_lut_10(entry));
+		intel_de_write_fw(dev_priv, PREC_PAL_DATA(pipe),
+				  ilk_lut_10(entry));
 	}
 
 	/*
 	 * Reset the index, otherwise it prevents the legacy palette to be
 	 * written properly.
 	 */
-	intel_de_write(dev_priv, PREC_PAL_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PREC_PAL_INDEX(pipe), 0);
 }
 
 static void ivb_load_lut_ext_max(const struct intel_crtc_state *crtc_state)
@@ -806,6 +806,14 @@
 	}
 }
 
+static int glk_degamma_lut_size(struct drm_i915_private *i915)
+{
+	if (DISPLAY_VER(i915) >= 13)
+		return 131;
+	else
+		return 35;
+}
+
 static void glk_load_degamma_lut(const struct intel_crtc_state *crtc_state)
 {
 	struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
@@ -819,14 +827,14 @@
 	 * ignore the index bits, so we need to reset it to index 0
 	 * separately.
 	 */
-	intel_de_write(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
-	intel_de_write(dev_priv, PRE_CSC_GAMC_INDEX(pipe),
-		       PRE_CSC_GAMC_AUTO_INCREMENT);
+	intel_de_write_fw(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PRE_CSC_GAMC_INDEX(pipe),
+			  PRE_CSC_GAMC_AUTO_INCREMENT);
 
 	for (i = 0; i < lut_size; i++) {
 		/*
-		 * First 33 entries represent range from 0 to 1.0
-		 * 34th and 35th entry will represent extended range
+		 * First lut_size entries represent range from 0 to 1.0
+		 * 3 additional lut entries will represent extended range
 		 * inputs 3.0 and 7.0 respectively, currently clamped
 		 * at 1.0. Since the precision is 16bit, the user
 		 * value can be directly filled to register.
@@ -837,15 +845,15 @@
 		 * ToDo: Extend to max 7.0. Enable 32 bit input value
 		 * as compared to just 16 to achieve this.
 		 */
-		intel_de_write(dev_priv, PRE_CSC_GAMC_DATA(pipe),
-			       lut[i].green);
+		intel_de_write_fw(dev_priv, PRE_CSC_GAMC_DATA(pipe),
+				  lut[i].green);
 	}
 
 	/* Clamp values > 1.0. */
-	while (i++ < 35)
-		intel_de_write(dev_priv, PRE_CSC_GAMC_DATA(pipe), 1 << 16);
+	while (i++ < glk_degamma_lut_size(dev_priv))
+		intel_de_write_fw(dev_priv, PRE_CSC_GAMC_DATA(pipe), 1 << 16);
 
-	intel_de_write(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
 }
 
 static void glk_load_degamma_lut_linear(const struct intel_crtc_state *crtc_state)
@@ -860,21 +868,21 @@
 	 * ignore the index bits, so we need to reset it to index 0
 	 * separately.
 	 */
-	intel_de_write(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
-	intel_de_write(dev_priv, PRE_CSC_GAMC_INDEX(pipe),
-		       PRE_CSC_GAMC_AUTO_INCREMENT);
+	intel_de_write_fw(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PRE_CSC_GAMC_INDEX(pipe),
+			  PRE_CSC_GAMC_AUTO_INCREMENT);
 
 	for (i = 0; i < lut_size; i++) {
 		u32 v = (i << 16) / (lut_size - 1);
 
-		intel_de_write(dev_priv, PRE_CSC_GAMC_DATA(pipe), v);
+		intel_de_write_fw(dev_priv, PRE_CSC_GAMC_DATA(pipe), v);
 	}
 
 	/* Clamp values > 1.0. */
 	while (i++ < 35)
-		intel_de_write(dev_priv, PRE_CSC_GAMC_DATA(pipe), 1 << 16);
+		intel_de_write_fw(dev_priv, PRE_CSC_GAMC_DATA(pipe), 1 << 16);
 
-	intel_de_write(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PRE_CSC_GAMC_INDEX(pipe), 0);
 }
 
 static void glk_load_luts(const struct intel_crtc_state *crtc_state)
@@ -1069,10 +1077,10 @@
 	enum pipe pipe = crtc->pipe;
 
 	for (i = 0; i < lut_size; i++) {
-		intel_de_write(dev_priv, CGM_PIPE_DEGAMMA(pipe, i, 0),
-			       chv_cgm_degamma_ldw(&lut[i]));
-		intel_de_write(dev_priv, CGM_PIPE_DEGAMMA(pipe, i, 1),
-			       chv_cgm_degamma_udw(&lut[i]));
+		intel_de_write_fw(dev_priv, CGM_PIPE_DEGAMMA(pipe, i, 0),
+				  chv_cgm_degamma_ldw(&lut[i]));
+		intel_de_write_fw(dev_priv, CGM_PIPE_DEGAMMA(pipe, i, 1),
+				  chv_cgm_degamma_udw(&lut[i]));
 	}
 }
 
@@ -1103,10 +1111,10 @@
 	enum pipe pipe = crtc->pipe;
 
 	for (i = 0; i < lut_size; i++) {
-		intel_de_write(dev_priv, CGM_PIPE_GAMMA(pipe, i, 0),
-			       chv_cgm_gamma_ldw(&lut[i]));
-		intel_de_write(dev_priv, CGM_PIPE_GAMMA(pipe, i, 1),
-			       chv_cgm_gamma_udw(&lut[i]));
+		intel_de_write_fw(dev_priv, CGM_PIPE_GAMMA(pipe, i, 0),
+				  chv_cgm_gamma_ldw(&lut[i]));
+		intel_de_write_fw(dev_priv, CGM_PIPE_GAMMA(pipe, i, 1),
+				  chv_cgm_gamma_udw(&lut[i]));
 	}
 }
 
@@ -1129,8 +1137,8 @@
 	else
 		i965_load_luts(crtc_state);
 
-	intel_de_write(dev_priv, CGM_PIPE_MODE(crtc->pipe),
-		       crtc_state->cgm_mode);
+	intel_de_write_fw(dev_priv, CGM_PIPE_MODE(crtc->pipe),
+			  crtc_state->cgm_mode);
 }
 
 void intel_color_load_luts(const struct intel_crtc_state *crtc_state)
@@ -1572,6 +1580,8 @@
 
 static u32 icl_gamma_mode(const struct intel_crtc_state *crtc_state)
 {
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
+	struct drm_i915_private *i915 = to_i915(crtc->base.dev);
 	u32 gamma_mode = 0;
 
 	if (crtc_state->hw.degamma_lut)
@@ -1584,6 +1594,13 @@
 	if (!crtc_state->hw.gamma_lut ||
 	    crtc_state_is_legacy_gamma(crtc_state))
 		gamma_mode |= GAMMA_MODE_MODE_8BIT;
+	/*
+	 * Enable 10bit gamma for D13
+	 * ToDo: Extend to Logarithmic Gamma once the new UAPI
+	 * is acccepted and implemented by a userspace consumer
+	 */
+	else if (DISPLAY_VER(i915) >= 13)
+		gamma_mode |= GAMMA_MODE_MODE_10BIT;
 	else
 		gamma_mode |= GAMMA_MODE_MODE_12BIT_MULTI_SEGMENTED;
 
@@ -1806,7 +1823,7 @@
 	lut = blob->data;
 
 	for (i = 0; i < LEGACY_LUT_LENGTH; i++) {
-		u32 val = intel_de_read(dev_priv, PALETTE(pipe, i));
+		u32 val = intel_de_read_fw(dev_priv, PALETTE(pipe, i));
 
 		i9xx_lut_8_pack(&lut[i], val);
 	}
@@ -1841,15 +1858,15 @@
 	lut = blob->data;
 
 	for (i = 0; i < lut_size - 1; i++) {
-		u32 ldw = intel_de_read(dev_priv, PALETTE(pipe, 2 * i + 0));
-		u32 udw = intel_de_read(dev_priv, PALETTE(pipe, 2 * i + 1));
+		u32 ldw = intel_de_read_fw(dev_priv, PALETTE(pipe, 2 * i + 0));
+		u32 udw = intel_de_read_fw(dev_priv, PALETTE(pipe, 2 * i + 1));
 
 		i965_lut_10p6_pack(&lut[i], ldw, udw);
 	}
 
-	lut[i].red = i965_lut_11p6_max_pack(intel_de_read(dev_priv, PIPEGCMAX(pipe, 0)));
-	lut[i].green = i965_lut_11p6_max_pack(intel_de_read(dev_priv, PIPEGCMAX(pipe, 1)));
-	lut[i].blue = i965_lut_11p6_max_pack(intel_de_read(dev_priv, PIPEGCMAX(pipe, 2)));
+	lut[i].red = i965_lut_11p6_max_pack(intel_de_read_fw(dev_priv, PIPEGCMAX(pipe, 0)));
+	lut[i].green = i965_lut_11p6_max_pack(intel_de_read_fw(dev_priv, PIPEGCMAX(pipe, 1)));
+	lut[i].blue = i965_lut_11p6_max_pack(intel_de_read_fw(dev_priv, PIPEGCMAX(pipe, 2)));
 
 	return blob;
 }
@@ -1884,8 +1901,8 @@
 	lut = blob->data;
 
 	for (i = 0; i < lut_size; i++) {
-		u32 ldw = intel_de_read(dev_priv, CGM_PIPE_GAMMA(pipe, i, 0));
-		u32 udw = intel_de_read(dev_priv, CGM_PIPE_GAMMA(pipe, i, 1));
+		u32 ldw = intel_de_read_fw(dev_priv, CGM_PIPE_GAMMA(pipe, i, 0));
+		u32 udw = intel_de_read_fw(dev_priv, CGM_PIPE_GAMMA(pipe, i, 1));
 
 		chv_cgm_gamma_pack(&lut[i], ldw, udw);
 	}
@@ -1920,7 +1937,7 @@
 	lut = blob->data;
 
 	for (i = 0; i < LEGACY_LUT_LENGTH; i++) {
-		u32 val = intel_de_read(dev_priv, LGC_PALETTE(pipe, i));
+		u32 val = intel_de_read_fw(dev_priv, LGC_PALETTE(pipe, i));
 
 		i9xx_lut_8_pack(&lut[i], val);
 	}
@@ -1945,7 +1962,7 @@
 	lut = blob->data;
 
 	for (i = 0; i < lut_size; i++) {
-		u32 val = intel_de_read(dev_priv, PREC_PALETTE(pipe, i));
+		u32 val = intel_de_read_fw(dev_priv, PREC_PALETTE(pipe, i));
 
 		ilk_lut_10_pack(&lut[i], val);
 	}
@@ -1997,16 +2014,16 @@
 
 	lut = blob->data;
 
-	intel_de_write(dev_priv, PREC_PAL_INDEX(pipe),
-		       prec_index | PAL_PREC_AUTO_INCREMENT);
+	intel_de_write_fw(dev_priv, PREC_PAL_INDEX(pipe),
+			  prec_index | PAL_PREC_AUTO_INCREMENT);
 
 	for (i = 0; i < lut_size; i++) {
-		u32 val = intel_de_read(dev_priv, PREC_PAL_DATA(pipe));
+		u32 val = intel_de_read_fw(dev_priv, PREC_PAL_DATA(pipe));
 
 		ilk_lut_10_pack(&lut[i], val);
 	}
 
-	intel_de_write(dev_priv, PREC_PAL_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PREC_PAL_INDEX(pipe), 0);
 
 	return blob;
 }
@@ -2048,17 +2065,17 @@
 
 	lut = blob->data;
 
-	intel_de_write(dev_priv, PREC_PAL_MULTI_SEG_INDEX(pipe),
-		       PAL_PREC_AUTO_INCREMENT);
+	intel_de_write_fw(dev_priv, PREC_PAL_MULTI_SEG_INDEX(pipe),
+			  PAL_PREC_AUTO_INCREMENT);
 
 	for (i = 0; i < 9; i++) {
-		u32 ldw = intel_de_read(dev_priv, PREC_PAL_MULTI_SEG_DATA(pipe));
-		u32 udw = intel_de_read(dev_priv, PREC_PAL_MULTI_SEG_DATA(pipe));
+		u32 ldw = intel_de_read_fw(dev_priv, PREC_PAL_MULTI_SEG_DATA(pipe));
+		u32 udw = intel_de_read_fw(dev_priv, PREC_PAL_MULTI_SEG_DATA(pipe));
 
 		icl_lut_multi_seg_pack(&lut[i], ldw, udw);
 	}
 
-	intel_de_write(dev_priv, PREC_PAL_MULTI_SEG_INDEX(pipe), 0);
+	intel_de_write_fw(dev_priv, PREC_PAL_MULTI_SEG_INDEX(pipe), 0);
 
 	/*
 	 * FIXME readouts from PAL_PREC_DATA register aren't giving
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_combo_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_combo_phy.c
@@ -24,18 +24,29 @@
 };
 
 static const struct icl_procmon {
+	const char *name;
 	u32 dw1, dw9, dw10;
 } icl_procmon_values[] = {
-	[PROCMON_0_85V_DOT_0] =
-		{ .dw1 = 0x00000000, .dw9 = 0x62AB67BB, .dw10 = 0x51914F96, },
-	[PROCMON_0_95V_DOT_0] =
-		{ .dw1 = 0x00000000, .dw9 = 0x86E172C7, .dw10 = 0x77CA5EAB, },
-	[PROCMON_0_95V_DOT_1] =
-		{ .dw1 = 0x00000000, .dw9 = 0x93F87FE1, .dw10 = 0x8AE871C5, },
-	[PROCMON_1_05V_DOT_0] =
-		{ .dw1 = 0x00000000, .dw9 = 0x98FA82DD, .dw10 = 0x89E46DC1, },
-	[PROCMON_1_05V_DOT_1] =
-		{ .dw1 = 0x00440000, .dw9 = 0x9A00AB25, .dw10 = 0x8AE38FF1, },
+	[PROCMON_0_85V_DOT_0] = {
+		.name = "0.85V dot0 (low-voltage)",
+		.dw1 = 0x00000000, .dw9 = 0x62AB67BB, .dw10 = 0x51914F96,
+	},
+	[PROCMON_0_95V_DOT_0] = {
+		.name = "0.95V dot0",
+		.dw1 = 0x00000000, .dw9 = 0x86E172C7, .dw10 = 0x77CA5EAB,
+	},
+	[PROCMON_0_95V_DOT_1] = {
+		.name = "0.95V dot1",
+		.dw1 = 0x00000000, .dw9 = 0x93F87FE1, .dw10 = 0x8AE871C5,
+	},
+	[PROCMON_1_05V_DOT_0] = {
+		.name = "1.05V dot0",
+		.dw1 = 0x00000000, .dw9 = 0x98FA82DD, .dw10 = 0x89E46DC1,
+	},
+	[PROCMON_1_05V_DOT_1] = {
+		.name = "1.05V dot1",
+		.dw1 = 0x00440000, .dw9 = 0x9A00AB25, .dw10 = 0x8AE38FF1,
+	},
 };
 
 static const struct icl_procmon *
@@ -112,6 +123,10 @@
 
 	procmon = icl_get_procmon_ref_values(dev_priv, phy);
 
+	drm_dbg_kms(&dev_priv->drm,
+		    "Combo PHY %c Voltage/Process Info : %s\n",
+		    phy_name(phy), procmon->name);
+
 	ret = check_phy_reg(dev_priv, phy, ICL_PORT_COMP_DW1(phy),
 			    (0xff << 16) | 0xff, procmon->dw1);
 	ret &= check_phy_reg(dev_priv, phy, ICL_PORT_COMP_DW9(phy),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_connector.c
@@ -29,13 +29,13 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_edid.h>
 
-#include "display/intel_panel.h"
-
 #include "i915_drv.h"
+#include "intel_backlight.h"
 #include "intel_connector.h"
 #include "intel_display_debugfs.h"
 #include "intel_display_types.h"
 #include "intel_hdcp.h"
+#include "intel_panel.h"
 
 int intel_connector_init(struct intel_connector *connector)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_crt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_crt.c
@@ -343,8 +343,13 @@
 	struct drm_device *dev = connector->dev;
 	struct drm_i915_private *dev_priv = to_i915(dev);
 	int max_dotclk = dev_priv->max_dotclk_freq;
+	enum drm_mode_status status;
 	int max_clock;
 
+	status = intel_cpu_transcoder_mode_valid(dev_priv, mode);
+	if (status != MODE_OK)
+		return status;
+
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return MODE_NO_DBLESCAN;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_cursor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_cursor.c
@@ -637,8 +637,7 @@
 	 * FIXME bigjoiner fastpath would be good
 	 */
 	if (!crtc_state->hw.active || intel_crtc_needs_modeset(crtc_state) ||
-	    crtc_state->update_pipe || crtc_state->bigjoiner ||
-	    crtc_state->enable_psr2_sel_fetch)
+	    crtc_state->update_pipe || crtc_state->bigjoiner)
 		goto slow;
 
 	/*
@@ -696,7 +695,7 @@
 		goto out_free;
 
 	intel_frontbuffer_flush(to_intel_frontbuffer(new_plane_state->hw.fb),
-				ORIGIN_FLIP);
+				ORIGIN_CURSOR_UPDATE);
 	intel_frontbuffer_track(to_intel_frontbuffer(old_plane_state->hw.fb),
 				to_intel_frontbuffer(new_plane_state->hw.fb),
 				plane->frontbuffer_bit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_ddi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -29,6 +29,7 @@
 
 #include "i915_drv.h"
 #include "intel_audio.h"
+#include "intel_backlight.h"
 #include "intel_combo_phy.h"
 #include "intel_connector.h"
 #include "intel_crtc.h"
@@ -40,6 +41,7 @@
 #include "intel_dp_link_training.h"
 #include "intel_dp_mst.h"
 #include "intel_dpio_phy.h"
+#include "intel_drrs.h"
 #include "intel_dsi.h"
 #include "intel_fdi.h"
 #include "intel_fifo_underrun.h"
@@ -48,7 +50,6 @@
 #include "intel_hdmi.h"
 #include "intel_hotplug.h"
 #include "intel_lspcon.h"
-#include "intel_panel.h"
 #include "intel_pps.h"
 #include "intel_psr.h"
 #include "intel_snps_phy.h"
@@ -287,7 +288,7 @@
 
 	if (IS_ALDERLAKE_P(i915) && intel_phy_is_tc(i915, phy)) {
 		intel_dp->DP |= ddi_buf_phy_link_rate(crtc_state->port_clock);
-		if (dig_port->tc_mode != TC_PORT_TBT_ALT)
+		if (!intel_tc_port_in_tbt_alt_mode(dig_port))
 			intel_dp->DP |= DDI_BUF_CTL_TC_PHY_OWNERSHIP;
 	}
 }
@@ -861,8 +862,7 @@
 
 	dig_port = enc_to_dig_port(encoder);
 
-	if (!intel_phy_is_tc(dev_priv, phy) ||
-	    dig_port->tc_mode != TC_PORT_TBT_ALT) {
+	if (!intel_tc_port_in_tbt_alt_mode(dig_port)) {
 		drm_WARN_ON(&dev_priv->drm, dig_port->ddi_io_wakeref);
 		dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
 								   dig_port->ddi_io_power_domain);
@@ -1156,7 +1156,7 @@
 	int n_entries, ln;
 	u32 val;
 
-	if (enc_to_dig_port(encoder)->tc_mode == TC_PORT_TBT_ALT)
+	if (intel_tc_port_in_tbt_alt_mode(enc_to_dig_port(encoder)))
 		return;
 
 	ddi_translations = encoder->get_buf_trans(encoder, crtc_state, &n_entries);
@@ -1293,7 +1293,7 @@
 	u32 val, dpcnt_mask, dpcnt_val;
 	int n_entries, ln;
 
-	if (enc_to_dig_port(encoder)->tc_mode == TC_PORT_TBT_ALT)
+	if (intel_tc_port_in_tbt_alt_mode(enc_to_dig_port(encoder)))
 		return;
 
 	ddi_translations = encoder->get_buf_trans(encoder, crtc_state, &n_entries);
@@ -2059,7 +2059,7 @@
 	u8 width;
 
 	if (!intel_phy_is_tc(dev_priv, phy) ||
-	    dig_port->tc_mode == TC_PORT_TBT_ALT)
+	    intel_tc_port_in_tbt_alt_mode(dig_port))
 		return;
 
 	if (DISPLAY_VER(dev_priv) >= 12) {
@@ -2084,7 +2084,7 @@
 	switch (pin_assignment) {
 	case 0x0:
 		drm_WARN_ON(&dev_priv->drm,
-			    dig_port->tc_mode != TC_PORT_LEGACY);
+			    !intel_tc_port_in_legacy_mode(dig_port));
 		if (width == 1) {
 			ln1 |= MG_DP_MODE_CFG_DP_X1_MODE;
 		} else {
@@ -2329,7 +2329,6 @@
 {
 	struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-	enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
 	struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
 	bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
 	int level = intel_ddi_dp_level(intel_dp);
@@ -2353,8 +2352,7 @@
 	intel_ddi_enable_clock(encoder, crtc_state);
 
 	/* 4. Enable IO power */
-	if (!intel_phy_is_tc(dev_priv, phy) ||
-	    dig_port->tc_mode != TC_PORT_TBT_ALT)
+	if (!intel_tc_port_in_tbt_alt_mode(dig_port))
 		dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
 								   dig_port->ddi_io_power_domain);
 
@@ -2439,7 +2437,6 @@
 {
 	struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-	enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
 	struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
 	bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
 	int level = intel_ddi_dp_level(intel_dp);
@@ -2476,8 +2473,7 @@
 	intel_ddi_enable_clock(encoder, crtc_state);
 
 	/* 5. If IO power is controlled through PWR_WELL_CTL, Enable IO Power */
-	if (!intel_phy_is_tc(dev_priv, phy) ||
-	    dig_port->tc_mode != TC_PORT_TBT_ALT) {
+	if (!intel_tc_port_in_tbt_alt_mode(dig_port)) {
 		drm_WARN_ON(&dev_priv->drm, dig_port->ddi_io_wakeref);
 		dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
 								   dig_port->ddi_io_power_domain);
@@ -2582,7 +2578,6 @@
 	struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	enum port port = encoder->port;
-	enum phy phy = intel_port_to_phy(dev_priv, port);
 	struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
 	bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
 	int level = intel_ddi_dp_level(intel_dp);
@@ -2601,8 +2596,7 @@
 
 	intel_ddi_enable_clock(encoder, crtc_state);
 
-	if (!intel_phy_is_tc(dev_priv, phy) ||
-	    dig_port->tc_mode != TC_PORT_TBT_ALT) {
+	if (!intel_tc_port_in_tbt_alt_mode(dig_port)) {
 		drm_WARN_ON(&dev_priv->drm, dig_port->ddi_io_wakeref);
 		dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
 								   dig_port->ddi_io_power_domain);
@@ -2772,7 +2766,6 @@
 	struct intel_dp *intel_dp = &dig_port->dp;
 	bool is_mst = intel_crtc_has_type(old_crtc_state,
 					  INTEL_OUTPUT_DP_MST);
-	enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
 
 	if (!is_mst)
 		intel_dp_set_infoframes(encoder, false,
@@ -2815,8 +2808,7 @@
 	intel_pps_vdd_on(intel_dp);
 	intel_pps_off(intel_dp);
 
-	if (!intel_phy_is_tc(dev_priv, phy) ||
-	    dig_port->tc_mode != TC_PORT_TBT_ALT)
+	if (!intel_tc_port_in_tbt_alt_mode(dig_port))
 		intel_display_power_put(dev_priv,
 					dig_port->ddi_io_power_domain,
 					fetch_and_zero(&dig_port->ddi_io_wakeref));
@@ -3293,7 +3285,7 @@
 						intel_ddi_main_link_aux_domain(dig_port));
 	}
 
-	if (is_tc_port && dig_port->tc_mode != TC_PORT_TBT_ALT)
+	if (is_tc_port && !intel_tc_port_in_tbt_alt_mode(dig_port))
 		/*
 		 * Program the lane count for static/dynamic connections on
 		 * Type-C ports.  Skip this step for TBT.
@@ -3995,8 +3987,11 @@
 {
 	struct drm_i915_private *i915 = to_i915(encoder->dev);
 	struct intel_digital_port *dig_port = enc_to_dig_port(to_intel_encoder(encoder));
+	enum phy phy = intel_port_to_phy(i915, dig_port->base.port);
 
 	intel_dp_encoder_flush_work(encoder);
+	if (intel_phy_is_tc(i915, phy))
+		intel_tc_port_flush_work(dig_port);
 	intel_display_power_flush_work(i915);
 
 	drm_encoder_cleanup(encoder);
@@ -4421,7 +4416,7 @@
 	if (!intel_phy_is_tc(i915, phy))
 		return;
 
-	intel_tc_port_disconnect_phy(dig_port);
+	intel_tc_port_flush_work(dig_port);
 }
 
 static void intel_ddi_encoder_shutdown(struct intel_encoder *encoder)
@@ -4432,11 +4427,12 @@
 	enum phy phy = intel_port_to_phy(i915, encoder->port);
 
 	intel_dp_encoder_shutdown(encoder);
+	intel_hdmi_encoder_shutdown(encoder);
 
 	if (!intel_phy_is_tc(i915, phy))
 		return;
 
-	intel_tc_port_disconnect_phy(dig_port);
+	intel_tc_port_flush_work(dig_port);
 }
 
 #define port_tc_name(port) ((port) - PORT_TC1 + '1')
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_ddi_buf_trans.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_ddi_buf_trans.c
@@ -476,14 +476,14 @@
 static const union intel_ddi_buf_trans_entry _ehl_combo_phy_ddi_translations_dp[] = {
 							/* NT mV Trans mV db    */
 	{ .icl = { 0xA, 0x33, 0x3F, 0x00, 0x00 } },	/* 350   350      0.0   */
-	{ .icl = { 0xA, 0x47, 0x36, 0x00, 0x09 } },	/* 350   500      3.1   */
-	{ .icl = { 0xC, 0x64, 0x34, 0x00, 0x0B } },	/* 350   700      6.0   */
-	{ .icl = { 0x6, 0x7F, 0x30, 0x00, 0x0F } },	/* 350   900      8.2   */
+	{ .icl = { 0xA, 0x47, 0x38, 0x00, 0x07 } },	/* 350   500      3.1   */
+	{ .icl = { 0xC, 0x64, 0x33, 0x00, 0x0C } },	/* 350   700      6.0   */
+	{ .icl = { 0x6, 0x7F, 0x2F, 0x00, 0x10 } },	/* 350   900      8.2   */
 	{ .icl = { 0xA, 0x46, 0x3F, 0x00, 0x00 } },	/* 500   500      0.0   */
-	{ .icl = { 0xC, 0x64, 0x38, 0x00, 0x07 } },	/* 500   700      2.9   */
+	{ .icl = { 0xC, 0x64, 0x37, 0x00, 0x08 } },	/* 500   700      2.9   */
 	{ .icl = { 0x6, 0x7F, 0x32, 0x00, 0x0D } },	/* 500   900      5.1   */
 	{ .icl = { 0xC, 0x61, 0x3F, 0x00, 0x00 } },	/* 650   700      0.6   */
-	{ .icl = { 0x6, 0x7F, 0x38, 0x00, 0x07 } },	/* 600   900      3.5   */
+	{ .icl = { 0x6, 0x7F, 0x37, 0x00, 0x08 } },	/* 600   900      3.5   */
 	{ .icl = { 0x6, 0x7F, 0x3F, 0x00, 0x00 } },	/* 900   900      0.0   */
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_display.c
@@ -84,6 +84,7 @@
 #include "intel_display_types.h"
 #include "intel_dmc.h"
 #include "intel_dp_link_training.h"
+#include "intel_dpt.h"
 #include "intel_fbc.h"
 #include "intel_fdi.h"
 #include "intel_fbdev.h"
@@ -126,182 +127,6 @@
 static void intel_modeset_setup_hw_state(struct drm_device *dev,
 					 struct drm_modeset_acquire_ctx *ctx);
 
-struct i915_dpt {
-	struct i915_address_space vm;
-
-	struct drm_i915_gem_object *obj;
-	struct i915_vma *vma;
-	void __iomem *iomem;
-};
-
-#define i915_is_dpt(vm) ((vm)->is_dpt)
-
-static inline struct i915_dpt *
-i915_vm_to_dpt(struct i915_address_space *vm)
-{
-	BUILD_BUG_ON(offsetof(struct i915_dpt, vm));
-	GEM_BUG_ON(!i915_is_dpt(vm));
-	return container_of(vm, struct i915_dpt, vm);
-}
-
-#define dpt_total_entries(dpt) ((dpt)->vm.total >> PAGE_SHIFT)
-
-static void gen8_set_pte(void __iomem *addr, gen8_pte_t pte)
-{
-	writeq(pte, addr);
-}
-
-static void dpt_insert_page(struct i915_address_space *vm,
-			    dma_addr_t addr,
-			    u64 offset,
-			    enum i915_cache_level level,
-			    u32 flags)
-{
-	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
-	gen8_pte_t __iomem *base = dpt->iomem;
-
-	gen8_set_pte(base + offset / I915_GTT_PAGE_SIZE,
-		     vm->pte_encode(addr, level, flags));
-}
-
-static void dpt_insert_entries(struct i915_address_space *vm,
-			       struct i915_vma *vma,
-			       enum i915_cache_level level,
-			       u32 flags)
-{
-	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
-	gen8_pte_t __iomem *base = dpt->iomem;
-	const gen8_pte_t pte_encode = vm->pte_encode(0, level, flags);
-	struct sgt_iter sgt_iter;
-	dma_addr_t addr;
-	int i;
-
-	/*
-	 * Note that we ignore PTE_READ_ONLY here. The caller must be careful
-	 * not to allow the user to override access to a read only page.
-	 */
-
-	i = vma->node.start / I915_GTT_PAGE_SIZE;
-	for_each_sgt_daddr(addr, sgt_iter, vma->pages)
-		gen8_set_pte(&base[i++], pte_encode | addr);
-}
-
-static void dpt_clear_range(struct i915_address_space *vm,
-			    u64 start, u64 length)
-{
-}
-
-static void dpt_bind_vma(struct i915_address_space *vm,
-			 struct i915_vm_pt_stash *stash,
-			 struct i915_vma *vma,
-			 enum i915_cache_level cache_level,
-			 u32 flags)
-{
-	struct drm_i915_gem_object *obj = vma->obj;
-	u32 pte_flags;
-
-	/* Applicable to VLV (gen8+ do not support RO in the GGTT) */
-	pte_flags = 0;
-	if (vma->vm->has_read_only && i915_gem_object_is_readonly(obj))
-		pte_flags |= PTE_READ_ONLY;
-	if (i915_gem_object_is_lmem(obj))
-		pte_flags |= PTE_LM;
-
-	vma->vm->insert_entries(vma->vm, vma, cache_level, pte_flags);
-
-	vma->page_sizes.gtt = I915_GTT_PAGE_SIZE;
-
-	/*
-	 * Without aliasing PPGTT there's no difference between
-	 * GLOBAL/LOCAL_BIND, it's all the same ptes. Hence unconditionally
-	 * upgrade to both bound if we bind either to avoid double-binding.
-	 */
-	atomic_or(I915_VMA_GLOBAL_BIND | I915_VMA_LOCAL_BIND, &vma->flags);
-}
-
-static void dpt_unbind_vma(struct i915_address_space *vm, struct i915_vma *vma)
-{
-	vm->clear_range(vm, vma->node.start, vma->size);
-}
-
-static void dpt_cleanup(struct i915_address_space *vm)
-{
-	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
-
-	i915_gem_object_put(dpt->obj);
-}
-
-static struct i915_address_space *
-intel_dpt_create(struct intel_framebuffer *fb)
-{
-	struct drm_gem_object *obj = &intel_fb_obj(&fb->base)->base;
-	struct drm_i915_private *i915 = to_i915(obj->dev);
-	struct drm_i915_gem_object *dpt_obj;
-	struct i915_address_space *vm;
-	struct i915_dpt *dpt;
-	size_t size;
-	int ret;
-
-	if (intel_fb_needs_pot_stride_remap(fb))
-		size = intel_remapped_info_size(&fb->remapped_view.gtt.remapped);
-	else
-		size = DIV_ROUND_UP_ULL(obj->size, I915_GTT_PAGE_SIZE);
-
-	size = round_up(size * sizeof(gen8_pte_t), I915_GTT_PAGE_SIZE);
-
-	if (HAS_LMEM(i915))
-		dpt_obj = i915_gem_object_create_lmem(i915, size, 0);
-	else
-		dpt_obj = i915_gem_object_create_stolen(i915, size);
-	if (IS_ERR(dpt_obj))
-		return ERR_CAST(dpt_obj);
-
-	ret = i915_gem_object_set_cache_level(dpt_obj, I915_CACHE_NONE);
-	if (ret) {
-		i915_gem_object_put(dpt_obj);
-		return ERR_PTR(ret);
-	}
-
-	dpt = kzalloc(sizeof(*dpt), GFP_KERNEL);
-	if (!dpt) {
-		i915_gem_object_put(dpt_obj);
-		return ERR_PTR(-ENOMEM);
-	}
-
-	vm = &dpt->vm;
-
-	vm->gt = &i915->gt;
-	vm->i915 = i915;
-	vm->dma = i915->drm.dev;
-	vm->total = (size / sizeof(gen8_pte_t)) * I915_GTT_PAGE_SIZE;
-	vm->is_dpt = true;
-
-	i915_address_space_init(vm, VM_CLASS_DPT);
-
-	vm->insert_page = dpt_insert_page;
-	vm->clear_range = dpt_clear_range;
-	vm->insert_entries = dpt_insert_entries;
-	vm->cleanup = dpt_cleanup;
-
-	vm->vma_ops.bind_vma    = dpt_bind_vma;
-	vm->vma_ops.unbind_vma  = dpt_unbind_vma;
-	vm->vma_ops.set_pages   = ggtt_set_pages;
-	vm->vma_ops.clear_pages = clear_pages;
-
-	vm->pte_encode = gen8_ggtt_pte_encode;
-
-	dpt->obj = dpt_obj;
-
-	return &dpt->vm;
-}
-
-static void intel_dpt_destroy(struct i915_address_space *vm)
-{
-	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
-
-	i915_vm_close(&dpt->vm);
-}
-
 /* returns HPLL frequency in kHz */
 int vlv_get_hpll_vco(struct drm_i915_private *dev_priv)
 {
@@ -1833,8 +1658,8 @@
 	}
 }
 
-static void intel_plane_disable_noatomic(struct intel_crtc *crtc,
-					 struct intel_plane *plane)
+void intel_plane_disable_noatomic(struct intel_crtc *crtc,
+				  struct intel_plane *plane)
 {
 	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
 	struct intel_crtc_state *crtc_state =
@@ -1879,49 +1704,6 @@
 	intel_wait_for_vblank(dev_priv, crtc->pipe);
 }
 
-static struct i915_vma *intel_dpt_pin(struct i915_address_space *vm)
-{
-	struct drm_i915_private *i915 = vm->i915;
-	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
-	intel_wakeref_t wakeref;
-	struct i915_vma *vma;
-	void __iomem *iomem;
-
-	wakeref = intel_runtime_pm_get(&i915->runtime_pm);
-	atomic_inc(&i915->gpu_error.pending_fb_pin);
-
-	vma = i915_gem_object_ggtt_pin(dpt->obj, NULL, 0, 4096,
-				       HAS_LMEM(i915) ? 0 : PIN_MAPPABLE);
-	if (IS_ERR(vma))
-		goto err;
-
-	iomem = i915_vma_pin_iomap(vma);
-	i915_vma_unpin(vma);
-	if (IS_ERR(iomem)) {
-		vma = iomem;
-		goto err;
-	}
-
-	dpt->vma = vma;
-	dpt->iomem = iomem;
-
-	i915_vma_get(vma);
-
-err:
-	atomic_dec(&i915->gpu_error.pending_fb_pin);
-	intel_runtime_pm_put(&i915->runtime_pm, wakeref);
-
-	return vma;
-}
-
-static void intel_dpt_unpin(struct i915_address_space *vm)
-{
-	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
-
-	i915_vma_unpin_iomap(dpt->vma);
-	i915_vma_put(dpt->vma);
-}
-
 static bool
 intel_reuse_initial_plane_obj(struct drm_i915_private *i915,
 			      const struct intel_initial_plane_config *plane_config,
@@ -2036,8 +1818,6 @@
 	plane_state->uapi.crtc = &crtc->base;
 	intel_plane_copy_uapi_to_hw_state(plane_state, plane_state, crtc);
 
-	intel_frontbuffer_flush(to_intel_frontbuffer(fb), ORIGIN_DIRTYFB);
-
 	atomic_or(plane->frontbuffer_bit, &to_intel_frontbuffer(fb)->bits);
 }
 
@@ -2212,26 +1992,6 @@
 	clear_bit_unlock(I915_RESET_MODESET, &dev_priv->gt.reset.flags);
 }
 
-static bool underrun_recovery_supported(const struct intel_crtc_state *crtc_state)
-{
-	if (crtc_state->pch_pfit.enabled &&
-	    (crtc_state->pipe_src_w > drm_rect_width(&crtc_state->pch_pfit.dst) ||
-	     crtc_state->pipe_src_h > drm_rect_height(&crtc_state->pch_pfit.dst) ||
-	     crtc_state->output_format == INTEL_OUTPUT_FORMAT_YCBCR420))
-		return false;
-
-	if (crtc_state->dsc.compression_enable)
-		return false;
-
-	if (crtc_state->has_psr2)
-		return false;
-
-	if (crtc_state->splitter.enable)
-		return false;
-
-	return true;
-}
-
 static void icl_set_pipe_chicken(const struct intel_crtc_state *crtc_state)
 {
 	struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
@@ -2255,19 +2015,14 @@
 	 */
 	tmp |= PIXEL_ROUNDING_TRUNC_FB_PASSTHRU;
 
-	if (IS_DG2(dev_priv)) {
-		/*
-		 * Underrun recovery must always be disabled on DG2.  However
-		 * the chicken bit meaning is inverted compared to other
-		 * platforms.
-		 */
+	/*
+	 * Underrun recovery must always be disabled on display 13+.
+	 * DG2 chicken bit meaning is inverted compared to other platforms.
+	 */
+	if (IS_DG2(dev_priv))
 		tmp &= ~UNDERRUN_RECOVERY_ENABLE_DG2;
-	} else if (DISPLAY_VER(dev_priv) >= 13) {
-		if (underrun_recovery_supported(crtc_state))
-			tmp &= ~UNDERRUN_RECOVERY_DISABLE_ADLP;
-		else
-			tmp |= UNDERRUN_RECOVERY_DISABLE_ADLP;
-	}
+	else if (DISPLAY_VER(dev_priv) >= 13)
+		tmp |= UNDERRUN_RECOVERY_DISABLE_ADLP;
 
 	intel_de_write(dev_priv, PIPE_CHICKEN(pipe), tmp);
 }
@@ -2521,7 +2276,7 @@
 		num_encoders++;
 	}
 
-	drm_WARN(encoder->base.dev, num_encoders != 1,
+	drm_WARN(state->base.dev, num_encoders != 1,
 		 "%d encoders for pipe %c\n",
 		 num_encoders, pipe_name(crtc->pipe));
 
@@ -3858,11 +3613,7 @@
 enum intel_display_power_domain
 intel_aux_power_domain(struct intel_digital_port *dig_port)
 {
-	struct drm_i915_private *dev_priv = to_i915(dig_port->base.base.dev);
-	enum phy phy = intel_port_to_phy(dev_priv, dig_port->base.port);
-
-	if (intel_phy_is_tc(dev_priv, phy) &&
-	    dig_port->tc_mode == TC_PORT_TBT_ALT) {
+	if (intel_tc_port_in_tbt_alt_mode(dig_port)) {
 		switch (dig_port->aux_ch) {
 		case AUX_CH_C:
 			return POWER_DOMAIN_AUX_C_TBT;
@@ -8042,6 +7793,7 @@
 	 * only fields that are know to not cause problems are preserved. */
 
 	saved_state->uapi = crtc_state->uapi;
+	saved_state->inherited = crtc_state->inherited;
 	saved_state->scaler_state = crtc_state->scaler_state;
 	saved_state->shared_dpll = crtc_state->shared_dpll;
 	saved_state->dpll_hw_state = crtc_state->dpll_hw_state;
@@ -8381,6 +8133,9 @@
 	if (dev_priv->params.fastboot != -1)
 		return dev_priv->params.fastboot;
 
+	if (dev_priv->quirks & QUIRK_FORCE_DISABLE_FASTBOOT)
+		return false;
+
 	/* Enable fastboot by default on Skylake and newer */
 	if (DISPLAY_VER(dev_priv) >= 9)
 		return true;
@@ -11287,7 +11042,6 @@
 		return ret;
 
 	i915_gem_object_wait_priority(obj, 0, &attr);
-	i915_gem_object_flush_frontbuffer(obj, ORIGIN_DIRTYFB);
 
 	if (!new_plane_state->uapi.fence) { /* implicit fencing */
 		struct dma_fence *fence;
@@ -12024,6 +11778,16 @@
 	    mode->vtotal > vtotal_max)
 		return MODE_V_ILLEGAL;
 
+	return MODE_OK;
+}
+
+enum drm_mode_status intel_cpu_transcoder_mode_valid(struct drm_i915_private *dev_priv,
+						     const struct drm_display_mode *mode)
+{
+	/*
+	 * Additional transcoder timing limits,
+	 * excluding BXT/GLK DSI transcoders.
+	 */
 	if (DISPLAY_VER(dev_priv) >= 5) {
 		if (mode->hdisplay < 64 ||
 		    mode->htotal - mode->hdisplay < 32)
@@ -12869,13 +12633,8 @@
 				intel_plane_disable_noatomic(crtc, plane);
 		}
 
-		/*
-		 * Disable any background color set by the BIOS, but enable the
-		 * gamma and CSC to match how we program our planes.
-		 */
-		if (DISPLAY_VER(dev_priv) >= 9)
-			intel_de_write(dev_priv, SKL_BOTTOM_COLOR(crtc->pipe),
-				       SKL_BOTTOM_COLOR_GAMMA_ENABLE | SKL_BOTTOM_COLOR_CSC_ENABLE);
+		/* Disable any background color/etc. set by the BIOS */
+		intel_color_commit(crtc_state);
 	}
 
 	/* Adjust the state of the output pipe according to whether we
@@ -13435,6 +13194,7 @@
 		vlv_wm_sanitize(dev_priv);
 	} else if (DISPLAY_VER(dev_priv) >= 9) {
 		skl_wm_get_hw_state(dev_priv);
+		skl_wm_sanitize(dev_priv);
 	} else if (HAS_PCH_SPLIT(dev_priv)) {
 		ilk_wm_get_hw_state(dev_priv);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_display.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_display.h
@@ -270,6 +270,7 @@
 };
 
 enum tc_port_mode {
+	TC_PORT_DISCONNECTED,
 	TC_PORT_TBT_ALT,
 	TC_PORT_DP_ALT,
 	TC_PORT_LEGACY,
@@ -527,6 +528,9 @@
 intel_mode_valid_max_plane_size(struct drm_i915_private *dev_priv,
 				const struct drm_display_mode *mode,
 				bool bigjoiner);
+enum drm_mode_status
+intel_cpu_transcoder_mode_valid(struct drm_i915_private *i915,
+				const struct drm_display_mode *mode);
 enum phy intel_port_to_phy(struct drm_i915_private *i915, enum port port);
 bool is_trans_port_sync_mode(const struct intel_crtc_state *state);
 
@@ -629,6 +633,8 @@
 struct intel_encoder *
 intel_get_crtc_new_encoder(const struct intel_atomic_state *state,
 			   const struct intel_crtc_state *crtc_state);
+void intel_plane_disable_noatomic(struct intel_crtc *crtc,
+				  struct intel_plane *plane);
 
 unsigned int intel_surf_alignment(const struct drm_framebuffer *fb,
 				  int color_plane);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_display_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_display_debugfs.c
@@ -13,6 +13,7 @@
 #include "intel_display_types.h"
 #include "intel_dmc.h"
 #include "intel_dp.h"
+#include "intel_drrs.h"
 #include "intel_fbc.h"
 #include "intel_hdcp.h"
 #include "intel_hdmi.h"
@@ -570,8 +571,8 @@
 		 * reg for DC3CO debugging and validation,
 		 * but TGL DMC f/w is using DMC_DEBUG3 reg for DC3CO counter.
 		 */
-		seq_printf(m, "DC3CO count: %d\n",
-			   intel_de_read(dev_priv, DMC_DEBUG3));
+		seq_printf(m, "DC3CO count: %d\n", intel_de_read(dev_priv, IS_DGFX(dev_priv) ?
+					DG1_DMC_DEBUG3 : TGL_DMC_DEBUG3));
 	} else {
 		dc5_reg = IS_BROXTON(dev_priv) ? BXT_DMC_DC3_DC5_COUNT :
 						 SKL_DMC_DC3_DC5_COUNT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_display_power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_display_power.c
@@ -560,7 +560,7 @@
 	if (drm_WARN_ON(&dev_priv->drm, !dig_port))
 		return;
 
-	if (DISPLAY_VER(dev_priv) == 11 && dig_port->tc_legacy_port)
+	if (DISPLAY_VER(dev_priv) == 11 && intel_tc_cold_requires_aux_pw(dig_port))
 		return;
 
 	drm_WARN_ON(&dev_priv->drm, !intel_tc_port_ref_held(dig_port));
@@ -629,7 +629,7 @@
 	 * exit sequence.
 	 */
 	timeout_expected = is_tbt || intel_tc_cold_requires_aux_pw(dig_port);
-	if (DISPLAY_VER(dev_priv) == 11 && dig_port->tc_legacy_port)
+	if (DISPLAY_VER(dev_priv) == 11 && intel_tc_cold_requires_aux_pw(dig_port))
 		icl_tc_cold_exit(dev_priv);
 
 	hsw_wait_for_power_well_enable(dev_priv, power_well, timeout_expected);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_display_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1520,6 +1520,8 @@
 	bool psr2_sel_fetch_enabled;
 	bool req_psr2_sdp_prior_scanline;
 	u8 sink_sync_latency;
+	u8 io_wake_lines;
+	u8 fast_wake_lines;
 	ktime_t last_entry_attempt;
 	ktime_t last_exit;
 	bool sink_not_reliable;
@@ -1639,6 +1641,9 @@
 	struct intel_dp_pcon_frl frl;
 
 	struct intel_psr psr;
+
+	/* When we last wrote the OUI for eDP */
+	unsigned long last_oui_write;
 };
 
 enum lspcon_vendor {
@@ -1667,8 +1672,11 @@
 	enum intel_display_power_domain ddi_io_power_domain;
 	intel_wakeref_t ddi_io_wakeref;
 	intel_wakeref_t aux_wakeref;
+
 	struct mutex tc_lock;	/* protects the TypeC port mode */
 	intel_wakeref_t tc_lock_wakeref;
+	enum intel_display_power_domain tc_lock_power_domain;
+	struct delayed_work tc_disconnect_phy_work;
 	int tc_link_refcount;
 	bool tc_legacy_port:1;
 	char tc_port_name[8];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dmc.c
@@ -45,8 +45,8 @@
 
 #define GEN12_DMC_MAX_FW_SIZE		ICL_DMC_MAX_FW_SIZE
 
-#define ADLP_DMC_PATH			DMC_PATH(adlp, 2, 10)
-#define ADLP_DMC_VERSION_REQUIRED	DMC_VERSION(2, 10)
+#define ADLP_DMC_PATH			DMC_PATH(adlp, 2, 12)
+#define ADLP_DMC_VERSION_REQUIRED	DMC_VERSION(2, 12)
 MODULE_FIRMWARE(ADLP_DMC_PATH);
 
 #define ADLS_DMC_PATH			DMC_PATH(adls, 2, 01)
@@ -375,6 +375,44 @@
 	}
 }
 
+static bool dmc_mmio_addr_sanity_check(struct intel_dmc *dmc,
+				       const u32 *mmioaddr, u32 mmio_count,
+				       int header_ver, u8 dmc_id)
+{
+	struct drm_i915_private *i915 = container_of(dmc, typeof(*i915), dmc);
+	u32 start_range, end_range;
+	int i;
+
+	if (dmc_id >= DMC_FW_MAX) {
+		drm_warn(&i915->drm, "Unsupported firmware id %u\n", dmc_id);
+		return false;
+	}
+
+	if (header_ver == 1) {
+		start_range = DMC_MMIO_START_RANGE;
+		end_range = DMC_MMIO_END_RANGE;
+	} else if (dmc_id == DMC_FW_MAIN) {
+		start_range = TGL_MAIN_MMIO_START;
+		end_range = TGL_MAIN_MMIO_END;
+	} else if (DISPLAY_VER(i915) >= 13) {
+		start_range = ADLP_PIPE_MMIO_START;
+		end_range = ADLP_PIPE_MMIO_END;
+	} else if (DISPLAY_VER(i915) >= 12) {
+		start_range = TGL_PIPE_MMIO_START(dmc_id);
+		end_range = TGL_PIPE_MMIO_END(dmc_id);
+	} else {
+		drm_warn(&i915->drm, "Unknown mmio range for sanity check");
+		return false;
+	}
+
+	for (i = 0; i < mmio_count; i++) {
+		if (mmioaddr[i] < start_range || mmioaddr[i] > end_range)
+			return false;
+	}
+
+	return true;
+}
+
 static u32 parse_dmc_fw_header(struct intel_dmc *dmc,
 			       const struct intel_dmc_header_base *dmc_header,
 			       size_t rem_size, u8 dmc_id)
@@ -444,6 +482,12 @@
 		return 0;
 	}
 
+	if (!dmc_mmio_addr_sanity_check(dmc, mmioaddr, mmio_count,
+					dmc_header->header_ver, dmc_id)) {
+		drm_err(&i915->drm, "DMC firmware has Wrong MMIO Addresses\n");
+		return 0;
+	}
+
 	for (i = 0; i < mmio_count; i++) {
 		dmc_info->mmioaddr[i] = _MMIO(mmioaddr[i]);
 		dmc_info->mmiodata[i] = mmiodata[i];
@@ -606,7 +650,7 @@
 			continue;
 
 		offset = readcount + dmc->dmc_info[id].dmc_offset * 4;
-		if (fw->size - offset < 0) {
+		if (offset > fw->size) {
 			drm_err(&dev_priv->drm, "Reading beyond the fw_size\n");
 			continue;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dp.c
@@ -29,6 +29,7 @@
 #include <linux/i2c.h>
 #include <linux/notifier.h>
 #include <linux/slab.h>
+#include <linux/timekeeping.h>
 #include <linux/types.h>
 
 #include <asm/byteorder.h>
@@ -44,6 +45,7 @@
 #include "i915_drv.h"
 #include "intel_atomic.h"
 #include "intel_audio.h"
+#include "intel_backlight.h"
 #include "intel_connector.h"
 #include "intel_ddi.h"
 #include "intel_de.h"
@@ -55,6 +57,7 @@
 #include "intel_dp_mst.h"
 #include "intel_dpio_phy.h"
 #include "intel_dpll.h"
+#include "intel_drrs.h"
 #include "intel_fifo_underrun.h"
 #include "intel_hdcp.h"
 #include "intel_hdmi.h"
@@ -111,6 +114,12 @@
 static void intel_dp_unset_edid(struct intel_dp *intel_dp);
 static int intel_dp_dsc_compute_bpp(struct intel_dp *intel_dp, u8 dsc_max_bpc);
 
+static void intel_dp_set_default_sink_rates(struct intel_dp *intel_dp)
+{
+	intel_dp->sink_rates[0] = 162000;
+	intel_dp->num_sink_rates = 1;
+}
+
 /* update sink rates from dpcd */
 static void intel_dp_set_sink_rates(struct intel_dp *intel_dp)
 {
@@ -217,6 +226,10 @@
 	struct intel_encoder *encoder = &intel_dig_port->base;
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 
+	/* eDP MSO is not compatible with joiner */
+	if (intel_dp->mso_link_count)
+		return false;
+
 	return DISPLAY_VER(dev_priv) >= 12 ||
 		(DISPLAY_VER(dev_priv) == 11 &&
 		 encoder->port != PORT_A);
@@ -275,7 +288,10 @@
 	if (DISPLAY_VER(dev_priv) >= 11) {
 		source_rates = icl_rates;
 		size = ARRAY_SIZE(icl_rates);
-		if (IS_JSL_EHL(dev_priv))
+		if (IS_ALDERLAKE_P(dev_priv) || IS_ALDERLAKE_S(dev_priv) ||
+			 IS_DG1(dev_priv) || IS_ROCKETLAKE(dev_priv))
+			max_rate = 810000;
+		else if (IS_JSL_EHL(dev_priv))
 			max_rate = ehl_max_source_rate(intel_dp);
 		else
 			max_rate = icl_max_source_rate(intel_dp);
@@ -719,8 +735,9 @@
 	enum drm_mode_status status;
 	bool dsc = false, bigjoiner = false;
 
-	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
-		return MODE_NO_DBLESCAN;
+	status = intel_cpu_transcoder_mode_valid(dev_priv, mode);
+	if (status != MODE_OK)
+		return status;
 
 	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
 		return MODE_H_ILLEGAL;
@@ -1222,6 +1239,11 @@
 		pipe_config->dsc.slice_count =
 			drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
 							true);
+		if (!pipe_config->dsc.slice_count) {
+			drm_dbg_kms(&dev_priv->drm, "Unsupported Slice Count %d\n",
+				    pipe_config->dsc.slice_count);
+			return -EINVAL;
+		}
 	} else {
 		u16 dsc_max_output_bpp;
 		u8 dsc_dp_slice_count;
@@ -1603,46 +1625,6 @@
 		intel_hdmi_infoframe_enable(HDMI_PACKET_TYPE_GAMUT_METADATA);
 }
 
-static void
-intel_dp_drrs_compute_config(struct intel_dp *intel_dp,
-			     struct intel_crtc_state *pipe_config,
-			     int output_bpp, bool constant_n)
-{
-	struct intel_connector *intel_connector = intel_dp->attached_connector;
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-	int pixel_clock;
-
-	if (pipe_config->vrr.enable)
-		return;
-
-	/*
-	 * DRRS and PSR can't be enable together, so giving preference to PSR
-	 * as it allows more power-savings by complete shutting down display,
-	 * so to guarantee this, intel_dp_drrs_compute_config() must be called
-	 * after intel_psr_compute_config().
-	 */
-	if (pipe_config->has_psr)
-		return;
-
-	if (!intel_connector->panel.downclock_mode ||
-	    dev_priv->drrs.type != SEAMLESS_DRRS_SUPPORT)
-		return;
-
-	pipe_config->has_drrs = true;
-
-	pixel_clock = intel_connector->panel.downclock_mode->clock;
-	if (pipe_config->splitter.enable)
-		pixel_clock /= pipe_config->splitter.link_count;
-
-	intel_link_compute_m_n(output_bpp, pipe_config->lane_count, pixel_clock,
-			       pipe_config->port_clock, &pipe_config->dp_m2_n2,
-			       constant_n, pipe_config->fec_enable);
-
-	/* FIXME: abstract this better */
-	if (pipe_config->splitter.enable)
-		pipe_config->dp_m2_n2.gmch_m *= pipe_config->splitter.link_count;
-}
-
 int
 intel_dp_compute_config(struct intel_encoder *encoder,
 			struct intel_crtc_state *pipe_config,
@@ -1692,7 +1674,7 @@
 	if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return -EINVAL;
 
-	if (HAS_GMCH(dev_priv) &&
+	if (!intel_connector->base.interlace_allowed &&
 	    adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE)
 		return -EINVAL;
 
@@ -1767,6 +1749,12 @@
 	intel_dp->lane_count = lane_count;
 }
 
+static void intel_dp_reset_max_link_params(struct intel_dp *intel_dp)
+{
+	intel_dp->max_link_lane_count = intel_dp_max_common_lane_count(intel_dp);
+	intel_dp->max_link_rate = intel_dp_max_common_rate(intel_dp);
+}
+
 /* Enable backlight PWM and backlight PP control. */
 void intel_edp_backlight_on(const struct intel_crtc_state *crtc_state,
 			    const struct drm_connector_state *conn_state)
@@ -1852,6 +1840,16 @@
 
 	if (drm_dp_dpcd_write(&intel_dp->aux, DP_SOURCE_OUI, oui, sizeof(oui)) < 0)
 		drm_err(&i915->drm, "Failed to write source OUI\n");
+
+	intel_dp->last_oui_write = jiffies;
+}
+
+void intel_dp_wait_source_oui(struct intel_dp *intel_dp)
+{
+	struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+
+	drm_dbg_kms(&i915->drm, "Performing OUI wait\n");
+	wait_remaining_ms_from_jiffies(intel_dp->last_oui_write, 30);
 }
 
 /* If the device supports it, try to set the power state appropriately */
@@ -1926,8 +1924,7 @@
 	if (intel_dp->dpcd[DP_DPCD_REV] == 0)
 		intel_dp_get_dpcd(intel_dp);
 
-	intel_dp->max_link_lane_count = intel_dp_max_common_lane_count(intel_dp);
-	intel_dp->max_link_rate = intel_dp_max_common_rate(intel_dp);
+	intel_dp_reset_max_link_params(intel_dp);
 }
 
 bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
@@ -2462,6 +2459,9 @@
 	 */
 	intel_psr_init_dpcd(intel_dp);
 
+	/* Clear the default sink rates */
+	intel_dp->num_sink_rates = 0;
+
 	/* Read the eDP 1.4+ supported link rates. */
 	if (intel_dp->edp_dpcd[0] >= DP_EDP_14) {
 		__le16 sink_rates[DP_MAX_SUPPORTED_RATES];
@@ -2497,6 +2497,7 @@
 		intel_dp_set_sink_rates(intel_dp);
 
 	intel_dp_set_common_rates(intel_dp);
+	intel_dp_reset_max_link_params(intel_dp);
 
 	/* Read the eDP DSC DPCD registers */
 	if (DISPLAY_VER(dev_priv) >= 10)
@@ -3257,61 +3258,6 @@
 	}
 }
 
-static void
-intel_dp_autotest_phy_ddi_disable(struct intel_dp *intel_dp,
-				  const struct intel_crtc_state *crtc_state)
-{
-	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
-	struct drm_device *dev = dig_port->base.base.dev;
-	struct drm_i915_private *dev_priv = to_i915(dev);
-	struct intel_crtc *crtc = to_intel_crtc(dig_port->base.base.crtc);
-	enum pipe pipe = crtc->pipe;
-	u32 trans_ddi_func_ctl_value, trans_conf_value, dp_tp_ctl_value;
-
-	trans_ddi_func_ctl_value = intel_de_read(dev_priv,
-						 TRANS_DDI_FUNC_CTL(pipe));
-	trans_conf_value = intel_de_read(dev_priv, PIPECONF(pipe));
-	dp_tp_ctl_value = intel_de_read(dev_priv, TGL_DP_TP_CTL(pipe));
-
-	trans_ddi_func_ctl_value &= ~(TRANS_DDI_FUNC_ENABLE |
-				      TGL_TRANS_DDI_PORT_MASK);
-	trans_conf_value &= ~PIPECONF_ENABLE;
-	dp_tp_ctl_value &= ~DP_TP_CTL_ENABLE;
-
-	intel_de_write(dev_priv, PIPECONF(pipe), trans_conf_value);
-	intel_de_write(dev_priv, TRANS_DDI_FUNC_CTL(pipe),
-		       trans_ddi_func_ctl_value);
-	intel_de_write(dev_priv, TGL_DP_TP_CTL(pipe), dp_tp_ctl_value);
-}
-
-static void
-intel_dp_autotest_phy_ddi_enable(struct intel_dp *intel_dp,
-				 const struct intel_crtc_state *crtc_state)
-{
-	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
-	struct drm_device *dev = dig_port->base.base.dev;
-	struct drm_i915_private *dev_priv = to_i915(dev);
-	enum port port = dig_port->base.port;
-	struct intel_crtc *crtc = to_intel_crtc(dig_port->base.base.crtc);
-	enum pipe pipe = crtc->pipe;
-	u32 trans_ddi_func_ctl_value, trans_conf_value, dp_tp_ctl_value;
-
-	trans_ddi_func_ctl_value = intel_de_read(dev_priv,
-						 TRANS_DDI_FUNC_CTL(pipe));
-	trans_conf_value = intel_de_read(dev_priv, PIPECONF(pipe));
-	dp_tp_ctl_value = intel_de_read(dev_priv, TGL_DP_TP_CTL(pipe));
-
-	trans_ddi_func_ctl_value |= TRANS_DDI_FUNC_ENABLE |
-				    TGL_TRANS_DDI_SELECT_PORT(port);
-	trans_conf_value |= PIPECONF_ENABLE;
-	dp_tp_ctl_value |= DP_TP_CTL_ENABLE;
-
-	intel_de_write(dev_priv, PIPECONF(pipe), trans_conf_value);
-	intel_de_write(dev_priv, TGL_DP_TP_CTL(pipe), dp_tp_ctl_value);
-	intel_de_write(dev_priv, TRANS_DDI_FUNC_CTL(pipe),
-		       trans_ddi_func_ctl_value);
-}
-
 static void intel_dp_process_phy_request(struct intel_dp *intel_dp,
 					 const struct intel_crtc_state *crtc_state)
 {
@@ -3329,19 +3275,15 @@
 	intel_dp_get_adjust_train(intel_dp, crtc_state, DP_PHY_DPRX,
 				  link_status);
 
-	intel_dp_autotest_phy_ddi_disable(intel_dp, crtc_state);
-
 	intel_dp_set_signal_levels(intel_dp, crtc_state, DP_PHY_DPRX);
 
 	intel_dp_phy_pattern_update(intel_dp, crtc_state);
 
-	intel_dp_autotest_phy_ddi_enable(intel_dp, crtc_state);
-
 	drm_dp_dpcd_write(&intel_dp->aux, DP_TRAINING_LANE0_SET,
 			  intel_dp->train_set, crtc_state->lane_count);
 
 	drm_dp_set_phy_test_pattern(&intel_dp->aux, data,
-				    link_status[DP_DPCD_REV]);
+				    intel_dp->dpcd[DP_DPCD_REV]);
 }
 
 static u8 intel_dp_autotest_phy_pattern(struct intel_dp *intel_dp)
@@ -3509,6 +3451,8 @@
 
 		drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base);
 
+		intel_dp->frl.is_trained = false;
+
 		/* Restart FRL training or fall back to TMDS mode */
 		intel_dp_check_frl_training(intel_dp);
 	}
@@ -3687,6 +3631,8 @@
 		    !intel_dp_mst_is_master_trans(crtc_state))
 			continue;
 
+		intel_dp->link_trained = false;
+
 		intel_dp_check_frl_training(intel_dp);
 		intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
 		intel_dp_start_link_train(intel_dp, crtc_state);
@@ -4022,7 +3968,7 @@
 	return is_connected;
 }
 
-static struct edid *
+struct edid *
 intel_dp_get_edid(struct intel_dp *intel_dp)
 {
 	struct intel_connector *intel_connector = intel_dp->attached_connector;
@@ -4240,12 +4186,7 @@
 	 * supports link training fallback params.
 	 */
 	if (intel_dp->reset_link_params || intel_dp->is_mst) {
-		/* Initial max link lane count */
-		intel_dp->max_link_lane_count = intel_dp_max_common_lane_count(intel_dp);
-
-		/* Initial max link rate */
-		intel_dp->max_link_rate = intel_dp_max_common_rate(intel_dp);
-
+		intel_dp_reset_max_link_params(intel_dp);
 		intel_dp->reset_link_params = false;
 	}
 
@@ -4617,7 +4558,7 @@
 	struct intel_dp *intel_dp = &dig_port->dp;
 
 	if (dig_port->base.type == INTEL_OUTPUT_EDP &&
-	    (long_hpd || !intel_pps_have_power(intel_dp))) {
+	    (long_hpd || !intel_pps_have_panel_power_or_vdd(intel_dp))) {
 		/*
 		 * vdd off can generate a long/short pulse on eDP which
 		 * would require vdd on to handle it, and thus we
@@ -4716,432 +4657,6 @@
 		drm_connector_attach_vrr_capable_property(connector);
 }
 
-/**
- * intel_dp_set_drrs_state - program registers for RR switch to take effect
- * @dev_priv: i915 device
- * @crtc_state: a pointer to the active intel_crtc_state
- * @refresh_rate: RR to be programmed
- *
- * This function gets called when refresh rate (RR) has to be changed from
- * one frequency to another. Switches can be between high and low RR
- * supported by the panel or to any other RR based on media playback (in
- * this case, RR value needs to be passed from user space).
- *
- * The caller of this function needs to take a lock on dev_priv->drrs.
- */
-static void intel_dp_set_drrs_state(struct drm_i915_private *dev_priv,
-				    const struct intel_crtc_state *crtc_state,
-				    int refresh_rate)
-{
-	struct intel_dp *intel_dp = dev_priv->drrs.dp;
-	struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
-	enum drrs_refresh_rate_type index = DRRS_HIGH_RR;
-
-	if (refresh_rate <= 0) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "Refresh rate should be positive non-zero.\n");
-		return;
-	}
-
-	if (intel_dp == NULL) {
-		drm_dbg_kms(&dev_priv->drm, "DRRS not supported.\n");
-		return;
-	}
-
-	if (!crtc) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "DRRS: intel_crtc not initialized\n");
-		return;
-	}
-
-	if (dev_priv->drrs.type < SEAMLESS_DRRS_SUPPORT) {
-		drm_dbg_kms(&dev_priv->drm, "Only Seamless DRRS supported.\n");
-		return;
-	}
-
-	if (drm_mode_vrefresh(intel_dp->attached_connector->panel.downclock_mode) ==
-			refresh_rate)
-		index = DRRS_LOW_RR;
-
-	if (index == dev_priv->drrs.refresh_rate_type) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "DRRS requested for previously set RR...ignoring\n");
-		return;
-	}
-
-	if (!crtc_state->hw.active) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "eDP encoder disabled. CRTC not Active\n");
-		return;
-	}
-
-	if (DISPLAY_VER(dev_priv) >= 8 && !IS_CHERRYVIEW(dev_priv)) {
-		switch (index) {
-		case DRRS_HIGH_RR:
-			intel_dp_set_m_n(crtc_state, M1_N1);
-			break;
-		case DRRS_LOW_RR:
-			intel_dp_set_m_n(crtc_state, M2_N2);
-			break;
-		case DRRS_MAX_RR:
-		default:
-			drm_err(&dev_priv->drm,
-				"Unsupported refreshrate type\n");
-		}
-	} else if (DISPLAY_VER(dev_priv) > 6) {
-		i915_reg_t reg = PIPECONF(crtc_state->cpu_transcoder);
-		u32 val;
-
-		val = intel_de_read(dev_priv, reg);
-		if (index > DRRS_HIGH_RR) {
-			if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
-				val |= PIPECONF_EDP_RR_MODE_SWITCH_VLV;
-			else
-				val |= PIPECONF_EDP_RR_MODE_SWITCH;
-		} else {
-			if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
-				val &= ~PIPECONF_EDP_RR_MODE_SWITCH_VLV;
-			else
-				val &= ~PIPECONF_EDP_RR_MODE_SWITCH;
-		}
-		intel_de_write(dev_priv, reg, val);
-	}
-
-	dev_priv->drrs.refresh_rate_type = index;
-
-	drm_dbg_kms(&dev_priv->drm, "eDP Refresh Rate set to : %dHz\n",
-		    refresh_rate);
-}
-
-static void
-intel_edp_drrs_enable_locked(struct intel_dp *intel_dp)
-{
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-
-	dev_priv->drrs.busy_frontbuffer_bits = 0;
-	dev_priv->drrs.dp = intel_dp;
-}
-
-/**
- * intel_edp_drrs_enable - init drrs struct if supported
- * @intel_dp: DP struct
- * @crtc_state: A pointer to the active crtc state.
- *
- * Initializes frontbuffer_bits and drrs.dp
- */
-void intel_edp_drrs_enable(struct intel_dp *intel_dp,
-			   const struct intel_crtc_state *crtc_state)
-{
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-
-	if (!crtc_state->has_drrs)
-		return;
-
-	drm_dbg_kms(&dev_priv->drm, "Enabling DRRS\n");
-
-	mutex_lock(&dev_priv->drrs.mutex);
-
-	if (dev_priv->drrs.dp) {
-		drm_warn(&dev_priv->drm, "DRRS already enabled\n");
-		goto unlock;
-	}
-
-	intel_edp_drrs_enable_locked(intel_dp);
-
-unlock:
-	mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-static void
-intel_edp_drrs_disable_locked(struct intel_dp *intel_dp,
-			      const struct intel_crtc_state *crtc_state)
-{
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-
-	if (dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR) {
-		int refresh;
-
-		refresh = drm_mode_vrefresh(intel_dp->attached_connector->panel.fixed_mode);
-		intel_dp_set_drrs_state(dev_priv, crtc_state, refresh);
-	}
-
-	dev_priv->drrs.dp = NULL;
-}
-
-/**
- * intel_edp_drrs_disable - Disable DRRS
- * @intel_dp: DP struct
- * @old_crtc_state: Pointer to old crtc_state.
- *
- */
-void intel_edp_drrs_disable(struct intel_dp *intel_dp,
-			    const struct intel_crtc_state *old_crtc_state)
-{
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-
-	if (!old_crtc_state->has_drrs)
-		return;
-
-	mutex_lock(&dev_priv->drrs.mutex);
-	if (!dev_priv->drrs.dp) {
-		mutex_unlock(&dev_priv->drrs.mutex);
-		return;
-	}
-
-	intel_edp_drrs_disable_locked(intel_dp, old_crtc_state);
-	mutex_unlock(&dev_priv->drrs.mutex);
-
-	cancel_delayed_work_sync(&dev_priv->drrs.work);
-}
-
-/**
- * intel_edp_drrs_update - Update DRRS state
- * @intel_dp: Intel DP
- * @crtc_state: new CRTC state
- *
- * This function will update DRRS states, disabling or enabling DRRS when
- * executing fastsets. For full modeset, intel_edp_drrs_disable() and
- * intel_edp_drrs_enable() should be called instead.
- */
-void
-intel_edp_drrs_update(struct intel_dp *intel_dp,
-		      const struct intel_crtc_state *crtc_state)
-{
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-
-	if (dev_priv->drrs.type != SEAMLESS_DRRS_SUPPORT)
-		return;
-
-	mutex_lock(&dev_priv->drrs.mutex);
-
-	/* New state matches current one? */
-	if (crtc_state->has_drrs == !!dev_priv->drrs.dp)
-		goto unlock;
-
-	if (crtc_state->has_drrs)
-		intel_edp_drrs_enable_locked(intel_dp);
-	else
-		intel_edp_drrs_disable_locked(intel_dp, crtc_state);
-
-unlock:
-	mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-static void intel_edp_drrs_downclock_work(struct work_struct *work)
-{
-	struct drm_i915_private *dev_priv =
-		container_of(work, typeof(*dev_priv), drrs.work.work);
-	struct intel_dp *intel_dp;
-
-	mutex_lock(&dev_priv->drrs.mutex);
-
-	intel_dp = dev_priv->drrs.dp;
-
-	if (!intel_dp)
-		goto unlock;
-
-	/*
-	 * The delayed work can race with an invalidate hence we need to
-	 * recheck.
-	 */
-
-	if (dev_priv->drrs.busy_frontbuffer_bits)
-		goto unlock;
-
-	if (dev_priv->drrs.refresh_rate_type != DRRS_LOW_RR) {
-		struct drm_crtc *crtc = dp_to_dig_port(intel_dp)->base.base.crtc;
-
-		intel_dp_set_drrs_state(dev_priv, to_intel_crtc(crtc)->config,
-			drm_mode_vrefresh(intel_dp->attached_connector->panel.downclock_mode));
-	}
-
-unlock:
-	mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * intel_edp_drrs_invalidate - Disable Idleness DRRS
- * @dev_priv: i915 device
- * @frontbuffer_bits: frontbuffer plane tracking bits
- *
- * This function gets called everytime rendering on the given planes start.
- * Hence DRRS needs to be Upclocked, i.e. (LOW_RR -> HIGH_RR).
- *
- * Dirty frontbuffers relevant to DRRS are tracked in busy_frontbuffer_bits.
- */
-void intel_edp_drrs_invalidate(struct drm_i915_private *dev_priv,
-			       unsigned int frontbuffer_bits)
-{
-	struct intel_dp *intel_dp;
-	struct drm_crtc *crtc;
-	enum pipe pipe;
-
-	if (dev_priv->drrs.type == DRRS_NOT_SUPPORTED)
-		return;
-
-	cancel_delayed_work(&dev_priv->drrs.work);
-
-	mutex_lock(&dev_priv->drrs.mutex);
-
-	intel_dp = dev_priv->drrs.dp;
-	if (!intel_dp) {
-		mutex_unlock(&dev_priv->drrs.mutex);
-		return;
-	}
-
-	crtc = dp_to_dig_port(intel_dp)->base.base.crtc;
-	pipe = to_intel_crtc(crtc)->pipe;
-
-	frontbuffer_bits &= INTEL_FRONTBUFFER_ALL_MASK(pipe);
-	dev_priv->drrs.busy_frontbuffer_bits |= frontbuffer_bits;
-
-	/* invalidate means busy screen hence upclock */
-	if (frontbuffer_bits && dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR)
-		intel_dp_set_drrs_state(dev_priv, to_intel_crtc(crtc)->config,
-					drm_mode_vrefresh(intel_dp->attached_connector->panel.fixed_mode));
-
-	mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * intel_edp_drrs_flush - Restart Idleness DRRS
- * @dev_priv: i915 device
- * @frontbuffer_bits: frontbuffer plane tracking bits
- *
- * This function gets called every time rendering on the given planes has
- * completed or flip on a crtc is completed. So DRRS should be upclocked
- * (LOW_RR -> HIGH_RR). And also Idleness detection should be started again,
- * if no other planes are dirty.
- *
- * Dirty frontbuffers relevant to DRRS are tracked in busy_frontbuffer_bits.
- */
-void intel_edp_drrs_flush(struct drm_i915_private *dev_priv,
-			  unsigned int frontbuffer_bits)
-{
-	struct intel_dp *intel_dp;
-	struct drm_crtc *crtc;
-	enum pipe pipe;
-
-	if (dev_priv->drrs.type == DRRS_NOT_SUPPORTED)
-		return;
-
-	cancel_delayed_work(&dev_priv->drrs.work);
-
-	mutex_lock(&dev_priv->drrs.mutex);
-
-	intel_dp = dev_priv->drrs.dp;
-	if (!intel_dp) {
-		mutex_unlock(&dev_priv->drrs.mutex);
-		return;
-	}
-
-	crtc = dp_to_dig_port(intel_dp)->base.base.crtc;
-	pipe = to_intel_crtc(crtc)->pipe;
-
-	frontbuffer_bits &= INTEL_FRONTBUFFER_ALL_MASK(pipe);
-	dev_priv->drrs.busy_frontbuffer_bits &= ~frontbuffer_bits;
-
-	/* flush means busy screen hence upclock */
-	if (frontbuffer_bits && dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR)
-		intel_dp_set_drrs_state(dev_priv, to_intel_crtc(crtc)->config,
-					drm_mode_vrefresh(intel_dp->attached_connector->panel.fixed_mode));
-
-	/*
-	 * flush also means no more activity hence schedule downclock, if all
-	 * other fbs are quiescent too
-	 */
-	if (!dev_priv->drrs.busy_frontbuffer_bits)
-		schedule_delayed_work(&dev_priv->drrs.work,
-				msecs_to_jiffies(1000));
-	mutex_unlock(&dev_priv->drrs.mutex);
-}
-
-/**
- * DOC: Display Refresh Rate Switching (DRRS)
- *
- * Display Refresh Rate Switching (DRRS) is a power conservation feature
- * which enables swtching between low and high refresh rates,
- * dynamically, based on the usage scenario. This feature is applicable
- * for internal panels.
- *
- * Indication that the panel supports DRRS is given by the panel EDID, which
- * would list multiple refresh rates for one resolution.
- *
- * DRRS is of 2 types - static and seamless.
- * Static DRRS involves changing refresh rate (RR) by doing a full modeset
- * (may appear as a blink on screen) and is used in dock-undock scenario.
- * Seamless DRRS involves changing RR without any visual effect to the user
- * and can be used during normal system usage. This is done by programming
- * certain registers.
- *
- * Support for static/seamless DRRS may be indicated in the VBT based on
- * inputs from the panel spec.
- *
- * DRRS saves power by switching to low RR based on usage scenarios.
- *
- * The implementation is based on frontbuffer tracking implementation.  When
- * there is a disturbance on the screen triggered by user activity or a periodic
- * system activity, DRRS is disabled (RR is changed to high RR).  When there is
- * no movement on screen, after a timeout of 1 second, a switch to low RR is
- * made.
- *
- * For integration with frontbuffer tracking code, intel_edp_drrs_invalidate()
- * and intel_edp_drrs_flush() are called.
- *
- * DRRS can be further extended to support other internal panels and also
- * the scenario of video playback wherein RR is set based on the rate
- * requested by userspace.
- */
-
-/**
- * intel_dp_drrs_init - Init basic DRRS work and mutex.
- * @connector: eDP connector
- * @fixed_mode: preferred mode of panel
- *
- * This function is  called only once at driver load to initialize basic
- * DRRS stuff.
- *
- * Returns:
- * Downclock mode if panel supports it, else return NULL.
- * DRRS support is determined by the presence of downclock mode (apart
- * from VBT setting).
- */
-static struct drm_display_mode *
-intel_dp_drrs_init(struct intel_connector *connector,
-		   struct drm_display_mode *fixed_mode)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct drm_display_mode *downclock_mode = NULL;
-
-	INIT_DELAYED_WORK(&dev_priv->drrs.work, intel_edp_drrs_downclock_work);
-	mutex_init(&dev_priv->drrs.mutex);
-
-	if (DISPLAY_VER(dev_priv) <= 6) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "DRRS supported for Gen7 and above\n");
-		return NULL;
-	}
-
-	if (dev_priv->vbt.drrs_type != SEAMLESS_DRRS_SUPPORT) {
-		drm_dbg_kms(&dev_priv->drm, "VBT doesn't support DRRS\n");
-		return NULL;
-	}
-
-	downclock_mode = intel_panel_edid_downclock_mode(connector, fixed_mode);
-	if (!downclock_mode) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "Downclock mode is not found. DRRS not supported\n");
-		return NULL;
-	}
-
-	dev_priv->drrs.type = dev_priv->vbt.drrs_type;
-
-	dev_priv->drrs.refresh_rate_type = DRRS_HIGH_RR;
-	drm_dbg_kms(&dev_priv->drm,
-		    "seamless DRRS supported for eDP panel.\n");
-	return downclock_mode;
-}
-
 static bool intel_edp_init_connector(struct intel_dp *intel_dp,
 				     struct intel_connector *intel_connector)
 {
@@ -5296,6 +4811,9 @@
 		return false;
 
 	intel_dp_set_source_rates(intel_dp);
+	intel_dp_set_default_sink_rates(intel_dp);
+	intel_dp_set_common_rates(intel_dp);
+	intel_dp_reset_max_link_params(intel_dp);
 
 	intel_dp->reset_link_params = true;
 	intel_dp->pps.pps_pipe = INVALID_PIPE;
@@ -5342,7 +4860,7 @@
 	drm_connector_init(dev, connector, &intel_dp_connector_funcs, type);
 	drm_connector_helper_add(connector, &intel_dp_connector_helper_funcs);
 
-	if (!HAS_GMCH(dev_priv))
+	if (!HAS_GMCH(dev_priv) && DISPLAY_VER(dev_priv) < 12)
 		connector->interlace_allowed = true;
 	connector->doublescan_allowed = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dp.h
@@ -70,17 +70,6 @@
 int intel_dp_max_lane_count(struct intel_dp *intel_dp);
 int intel_dp_rate_select(struct intel_dp *intel_dp, int rate);
 
-void intel_edp_drrs_enable(struct intel_dp *intel_dp,
-			   const struct intel_crtc_state *crtc_state);
-void intel_edp_drrs_disable(struct intel_dp *intel_dp,
-			    const struct intel_crtc_state *crtc_state);
-void intel_edp_drrs_update(struct intel_dp *intel_dp,
-			   const struct intel_crtc_state *crtc_state);
-void intel_edp_drrs_invalidate(struct drm_i915_private *dev_priv,
-			       unsigned int frontbuffer_bits);
-void intel_edp_drrs_flush(struct drm_i915_private *dev_priv,
-			  unsigned int frontbuffer_bits);
-
 void intel_dp_compute_rate(struct intel_dp *intel_dp, int port_clock,
 			   u8 *link_bw, u8 *rate_select);
 bool intel_dp_source_supports_hbr2(struct intel_dp *intel_dp);
@@ -107,6 +96,8 @@
 		       unsigned int type);
 bool intel_digital_port_connected(struct intel_encoder *encoder);
 
+struct edid *intel_dp_get_edid(struct intel_dp *intel_dp);
+
 static inline unsigned int intel_dp_unused_lane_mask(int lane_count)
 {
 	return ~((1 << lane_count) - 1) & 0xf;
@@ -129,4 +120,6 @@
 				 const struct intel_crtc_state *crtc_state);
 void intel_dp_phy_test(struct intel_encoder *encoder);
 
+void intel_dp_wait_source_oui(struct intel_dp *intel_dp);
+
 #endif /* __INTEL_DP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dp_aux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dp_aux.c
@@ -119,6 +119,32 @@
 	return index ? 0 : 1;
 }
 
+static int intel_dp_aux_sync_len(void)
+{
+	int precharge = 16; /* 10-16 */
+	int preamble = 16;
+
+	return precharge + preamble;
+}
+
+static int intel_dp_aux_fw_sync_len(void)
+{
+	int precharge = 10; /* 10-16 */
+	int preamble = 8;
+
+	return precharge + preamble;
+}
+
+static int g4x_dp_aux_precharge_len(void)
+{
+	int precharge_min = 10;
+	int preamble = 16;
+
+	/* HW wants the length of the extra precharge in 2us units */
+	return (intel_dp_aux_sync_len() -
+		precharge_min - preamble) / 2;
+}
+
 static u32 g4x_get_aux_send_ctl(struct intel_dp *intel_dp,
 				int send_bytes,
 				u32 aux_clock_divider)
@@ -141,7 +167,7 @@
 	       timeout |
 	       DP_AUX_CH_CTL_RECEIVE_ERROR |
 	       (send_bytes << DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT) |
-	       (3 << DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT) |
+	       (g4x_dp_aux_precharge_len() << DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT) |
 	       (aux_clock_divider << DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT);
 }
 
@@ -150,9 +176,6 @@
 				u32 unused)
 {
 	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
-	struct drm_i915_private *i915 =
-			to_i915(dig_port->base.base.dev);
-	enum phy phy = intel_port_to_phy(i915, dig_port->base.port);
 	u32 ret;
 
 	/*
@@ -167,11 +190,10 @@
 	      DP_AUX_CH_CTL_TIME_OUT_MAX |
 	      DP_AUX_CH_CTL_RECEIVE_ERROR |
 	      (send_bytes << DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT) |
-	      DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL(32) |
-	      DP_AUX_CH_CTL_SYNC_PULSE_SKL(32);
+	      DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL(intel_dp_aux_fw_sync_len()) |
+	      DP_AUX_CH_CTL_SYNC_PULSE_SKL(intel_dp_aux_sync_len());
 
-	if (intel_phy_is_tc(i915, phy) &&
-	    dig_port->tc_mode == TC_PORT_TBT_ALT)
+	if (intel_tc_port_in_tbt_alt_mode(dig_port))
 		ret |= DP_AUX_CH_CTL_TBT_IO;
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
@@ -34,9 +34,10 @@
  * for some reason.
  */
 
+#include "intel_backlight.h"
 #include "intel_display_types.h"
+#include "intel_dp.h"
 #include "intel_dp_aux_backlight.h"
-#include "intel_panel.h"
 
 /* TODO:
  * Implement HDR, right now we just implement the bare minimum to bring us back into SDR mode so we
@@ -95,6 +96,14 @@
 
 #define INTEL_EDP_BRIGHTNESS_OPTIMIZATION_1                            0x359
 
+enum intel_dp_aux_backlight_modparam {
+	INTEL_DP_AUX_BACKLIGHT_AUTO = -1,
+	INTEL_DP_AUX_BACKLIGHT_OFF = 0,
+	INTEL_DP_AUX_BACKLIGHT_ON = 1,
+	INTEL_DP_AUX_BACKLIGHT_FORCE_VESA = 2,
+	INTEL_DP_AUX_BACKLIGHT_FORCE_INTEL = 3,
+};
+
 /* Intel EDP backlight callbacks */
 static bool
 intel_dp_aux_supports_hdr_backlight(struct intel_connector *connector)
@@ -106,6 +115,8 @@
 	int ret;
 	u8 tcon_cap[4];
 
+	intel_dp_wait_source_oui(intel_dp);
+
 	ret = drm_dp_dpcd_read(aux, INTEL_EDP_HDR_TCON_CAP0, tcon_cap, sizeof(tcon_cap));
 	if (ret != sizeof(tcon_cap))
 		return false;
@@ -122,6 +133,24 @@
 		return false;
 	}
 
+	/*
+	 * If we don't have HDR static metadata there is no way to
+	 * runtime detect used range for nits based control. For now
+	 * do not use Intel proprietary eDP backlight control if we
+	 * don't have this data in panel EDID. In case we find panel
+	 * which supports only nits based control, but doesn't provide
+	 * HDR static metadata we need to start maintaining table of
+	 * ranges for such panels.
+	 */
+	if (i915->params.enable_dpcd_backlight != INTEL_DP_AUX_BACKLIGHT_FORCE_INTEL &&
+	    !(connector->base.hdr_sink_metadata.hdmi_type1.metadata_type &
+	      BIT(HDMI_STATIC_METADATA_TYPE1))) {
+		drm_info(&i915->drm,
+			 "Panel is missing HDR static metadata. Possible support for Intel HDR backlight interface is not used. If your backlight controls don't work try booting with i915.enable_dpcd_backlight=%d. needs this, please file a _new_ bug report on drm/i915, see " FDO_BUG_URL " for details.\n",
+			 INTEL_DP_AUX_BACKLIGHT_FORCE_INTEL);
+		return false;
+	}
+
 	panel->backlight.edp.intel.sdr_uses_aux =
 		tcon_cap[2] & INTEL_EDP_SDR_TCON_BRIGHTNESS_AUX_CAP;
 
@@ -204,6 +233,8 @@
 	int ret;
 	u8 old_ctrl, ctrl;
 
+	intel_dp_wait_source_oui(intel_dp);
+
 	ret = drm_dp_dpcd_readb(&intel_dp->aux, INTEL_EDP_HDR_GETSET_CTRL_PARAMS, &old_ctrl);
 	if (ret != 1) {
 		drm_err(&i915->drm, "Failed to read current backlight control mode: %d\n", ret);
@@ -246,6 +277,8 @@
 {
 	struct drm_i915_private *i915 = to_i915(connector->base.dev);
 	struct intel_panel *panel = &connector->panel;
+	struct drm_luminance_range_info *luminance_range =
+		&connector->base.display_info.luminance_range;
 	int ret;
 
 	if (panel->backlight.edp.intel.sdr_uses_aux) {
@@ -261,8 +294,17 @@
 		}
 	}
 
-	panel->backlight.max = 512;
-	panel->backlight.min = 0;
+	if (luminance_range->max_luminance) {
+		panel->backlight.max = luminance_range->max_luminance;
+		panel->backlight.min = luminance_range->min_luminance;
+	} else {
+		panel->backlight.max = 512;
+		panel->backlight.min = 0;
+	}
+
+	drm_dbg_kms(&i915->drm, "Using backlight range %d..%d\n", panel->backlight.min,
+		    panel->backlight.max);
+
 	panel->backlight.level = intel_dp_aux_hdr_get_backlight(connector, pipe);
 	panel->backlight.enabled = panel->backlight.level != 0;
 
@@ -368,14 +410,6 @@
 	.get = intel_dp_aux_vesa_get_backlight,
 };
 
-enum intel_dp_aux_backlight_modparam {
-	INTEL_DP_AUX_BACKLIGHT_AUTO = -1,
-	INTEL_DP_AUX_BACKLIGHT_OFF = 0,
-	INTEL_DP_AUX_BACKLIGHT_ON = 1,
-	INTEL_DP_AUX_BACKLIGHT_FORCE_VESA = 2,
-	INTEL_DP_AUX_BACKLIGHT_FORCE_INTEL = 3,
-};
-
 int intel_dp_aux_init_backlight_funcs(struct intel_connector *connector)
 {
 	struct drm_device *dev = connector->base.dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dp_link_training.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dp_link_training.c
@@ -475,6 +475,28 @@
 	intel_dp_compute_rate(intel_dp, crtc_state->port_clock,
 			      &link_bw, &rate_select);
 
+	/*
+	 * WaEdpLinkRateDataReload
+	 *
+	 * Parade PS8461E MUX (used on varius TGL+ laptops) needs
+	 * to snoop the link rates reported by the sink when we
+	 * use LINK_RATE_SET in order to operate in jitter cleaning
+	 * mode (as opposed to redriver mode). Unfortunately it
+	 * loses track of the snooped link rates when powered down,
+	 * so we need to make it re-snoop often. Without this high
+	 * link rates are not stable.
+	 */
+	if (!link_bw) {
+		struct intel_connector *connector = intel_dp->attached_connector;
+		__le16 sink_rates[DP_MAX_SUPPORTED_RATES];
+
+		drm_dbg_kms(&i915->drm, "[CONNECTOR:%d:%s] Reloading eDP link rates\n",
+			    connector->base.base.id, connector->base.name);
+
+		drm_dp_dpcd_read(&intel_dp->aux, DP_SUPPORTED_LINK_RATES,
+				 sink_rates, sizeof(sink_rates));
+	}
+
 	if (link_bw)
 		drm_dbg_kms(&i915->drm,
 			    "Using LINK_BW_SET value %02x\n", link_bw);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dp_mst.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dp_mst.c
@@ -697,6 +697,10 @@
 		return 0;
 	}
 
+	*status = intel_cpu_transcoder_mode_valid(dev_priv, mode);
+	if (*status != MODE_OK)
+		return 0;
+
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN) {
 		*status = MODE_NO_DBLESCAN;
 		return 0;
@@ -817,6 +821,7 @@
 	ret = drm_connector_init(dev, connector, &intel_dp_mst_connector_funcs,
 				 DRM_MODE_CONNECTOR_DisplayPort);
 	if (ret) {
+		drm_dp_mst_put_port_malloc(port);
 		intel_connector_free(intel_connector);
 		return NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
@@ -26,6 +26,7 @@
 #include "intel_dpio_phy.h"
 #include "intel_dpll.h"
 #include "intel_dpll_mgr.h"
+#include "intel_tc.h"
 
 /**
  * DOC: Display PLLs
@@ -2434,7 +2435,7 @@
 }
 
 /*
- * Display WA #22010492432: ehl, tgl, adl-p
+ * Display WA #22010492432: ehl, tgl, adl-s, adl-p
  * Program half of the nominal DCO divider fraction value.
  */
 static bool
@@ -2442,7 +2443,7 @@
 {
 	return ((IS_PLATFORM(i915, INTEL_ELKHARTLAKE) &&
 		 IS_JSL_EHL_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
-		 IS_TIGERLAKE(i915) || IS_ALDERLAKE_P(i915)) &&
+		 IS_TIGERLAKE(i915) || IS_ALDERLAKE_S(i915) || IS_ALDERLAKE_P(i915)) &&
 		 i915->dpll.ref_clks.nssc == 38400;
 }
 
@@ -3136,8 +3137,8 @@
 		enc_to_dig_port(encoder);
 
 	if (primary_port &&
-	    (primary_port->tc_mode == TC_PORT_DP_ALT ||
-	     primary_port->tc_mode == TC_PORT_LEGACY))
+	    (intel_tc_port_in_dp_alt_mode(primary_port) ||
+	     intel_tc_port_in_legacy_mode(primary_port)))
 		port_dpll_id = ICL_PORT_DPLL_MG_PHY;
 
 	icl_set_active_port_dpll(crtc_state, port_dpll_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dpt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dpt.c
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright © 2021 Intel Corporation
+ */
+
+#include "i915_drv.h"
+#include "intel_display_types.h"
+#include "intel_dpt.h"
+#include "intel_fb.h"
+#include "gt/gen8_ppgtt.h"
+
+struct i915_dpt {
+	struct i915_address_space vm;
+
+	struct drm_i915_gem_object *obj;
+	struct i915_vma *vma;
+	void __iomem *iomem;
+};
+
+#define i915_is_dpt(vm) ((vm)->is_dpt)
+
+static inline struct i915_dpt *
+i915_vm_to_dpt(struct i915_address_space *vm)
+{
+	BUILD_BUG_ON(offsetof(struct i915_dpt, vm));
+	GEM_BUG_ON(!i915_is_dpt(vm));
+	return container_of(vm, struct i915_dpt, vm);
+}
+
+#define dpt_total_entries(dpt) ((dpt)->vm.total >> PAGE_SHIFT)
+
+static void gen8_set_pte(void __iomem *addr, gen8_pte_t pte)
+{
+	writeq(pte, addr);
+}
+
+static void dpt_insert_page(struct i915_address_space *vm,
+			    dma_addr_t addr,
+			    u64 offset,
+			    enum i915_cache_level level,
+			    u32 flags)
+{
+	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
+	gen8_pte_t __iomem *base = dpt->iomem;
+
+	gen8_set_pte(base + offset / I915_GTT_PAGE_SIZE,
+		     vm->pte_encode(addr, level, flags));
+}
+
+static void dpt_insert_entries(struct i915_address_space *vm,
+			       struct i915_vma *vma,
+			       enum i915_cache_level level,
+			       u32 flags)
+{
+	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
+	gen8_pte_t __iomem *base = dpt->iomem;
+	const gen8_pte_t pte_encode = vm->pte_encode(0, level, flags);
+	struct sgt_iter sgt_iter;
+	dma_addr_t addr;
+	int i;
+
+	/*
+	 * Note that we ignore PTE_READ_ONLY here. The caller must be careful
+	 * not to allow the user to override access to a read only page.
+	 */
+
+	i = vma->node.start / I915_GTT_PAGE_SIZE;
+	for_each_sgt_daddr(addr, sgt_iter, vma->pages)
+		gen8_set_pte(&base[i++], pte_encode | addr);
+}
+
+static void dpt_clear_range(struct i915_address_space *vm,
+			    u64 start, u64 length)
+{
+}
+
+static void dpt_bind_vma(struct i915_address_space *vm,
+			 struct i915_vm_pt_stash *stash,
+			 struct i915_vma *vma,
+			 enum i915_cache_level cache_level,
+			 u32 flags)
+{
+	struct drm_i915_gem_object *obj = vma->obj;
+	u32 pte_flags;
+
+	/* Applicable to VLV (gen8+ do not support RO in the GGTT) */
+	pte_flags = 0;
+	if (vma->vm->has_read_only && i915_gem_object_is_readonly(obj))
+		pte_flags |= PTE_READ_ONLY;
+	if (i915_gem_object_is_lmem(obj))
+		pte_flags |= PTE_LM;
+
+	vma->vm->insert_entries(vma->vm, vma, cache_level, pte_flags);
+
+	vma->page_sizes.gtt = I915_GTT_PAGE_SIZE;
+
+	/*
+	 * Without aliasing PPGTT there's no difference between
+	 * GLOBAL/LOCAL_BIND, it's all the same ptes. Hence unconditionally
+	 * upgrade to both bound if we bind either to avoid double-binding.
+	 */
+	atomic_or(I915_VMA_GLOBAL_BIND | I915_VMA_LOCAL_BIND, &vma->flags);
+}
+
+static void dpt_unbind_vma(struct i915_address_space *vm, struct i915_vma *vma)
+{
+	vm->clear_range(vm, vma->node.start, vma->size);
+}
+
+static void dpt_cleanup(struct i915_address_space *vm)
+{
+	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
+
+	i915_gem_object_put(dpt->obj);
+}
+
+struct i915_vma *intel_dpt_pin(struct i915_address_space *vm)
+{
+	struct drm_i915_private *i915 = vm->i915;
+	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
+	intel_wakeref_t wakeref;
+	struct i915_vma *vma;
+	void __iomem *iomem;
+
+	wakeref = intel_runtime_pm_get(&i915->runtime_pm);
+	atomic_inc(&i915->gpu_error.pending_fb_pin);
+
+	vma = i915_gem_object_ggtt_pin(dpt->obj, NULL, 0, 4096,
+				       HAS_LMEM(i915) ? 0 : PIN_MAPPABLE);
+	if (IS_ERR(vma))
+		goto err;
+
+	iomem = i915_vma_pin_iomap(vma);
+	i915_vma_unpin(vma);
+	if (IS_ERR(iomem)) {
+		vma = iomem;
+		goto err;
+	}
+
+	dpt->vma = vma;
+	dpt->iomem = iomem;
+
+	i915_vma_get(vma);
+
+err:
+	atomic_dec(&i915->gpu_error.pending_fb_pin);
+	intel_runtime_pm_put(&i915->runtime_pm, wakeref);
+
+	return vma;
+}
+
+void intel_dpt_unpin(struct i915_address_space *vm)
+{
+	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
+
+	i915_vma_unpin_iomap(dpt->vma);
+	i915_vma_put(dpt->vma);
+}
+
+struct i915_address_space *
+intel_dpt_create(struct intel_framebuffer *fb)
+{
+	struct drm_gem_object *obj = &intel_fb_obj(&fb->base)->base;
+	struct drm_i915_private *i915 = to_i915(obj->dev);
+	struct drm_i915_gem_object *dpt_obj;
+	struct i915_address_space *vm;
+	struct i915_dpt *dpt;
+	size_t size;
+	int ret;
+
+	if (intel_fb_needs_pot_stride_remap(fb))
+		size = intel_remapped_info_size(&fb->remapped_view.gtt.remapped);
+	else
+		size = DIV_ROUND_UP_ULL(obj->size, I915_GTT_PAGE_SIZE);
+
+	size = round_up(size * sizeof(gen8_pte_t), I915_GTT_PAGE_SIZE);
+
+	if (HAS_LMEM(i915))
+		dpt_obj = i915_gem_object_create_lmem(i915, size, 0);
+	else
+		dpt_obj = i915_gem_object_create_stolen(i915, size);
+	if (IS_ERR(dpt_obj))
+		return ERR_CAST(dpt_obj);
+
+	ret = i915_gem_object_set_cache_level(dpt_obj, I915_CACHE_NONE);
+	if (ret) {
+		i915_gem_object_put(dpt_obj);
+		return ERR_PTR(ret);
+	}
+
+	dpt = kzalloc(sizeof(*dpt), GFP_KERNEL);
+	if (!dpt) {
+		i915_gem_object_put(dpt_obj);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	vm = &dpt->vm;
+
+	vm->gt = &i915->gt;
+	vm->i915 = i915;
+	vm->dma = i915->drm.dev;
+	vm->total = (size / sizeof(gen8_pte_t)) * I915_GTT_PAGE_SIZE;
+	vm->is_dpt = true;
+
+	i915_address_space_init(vm, VM_CLASS_DPT);
+
+	vm->insert_page = dpt_insert_page;
+	vm->clear_range = dpt_clear_range;
+	vm->insert_entries = dpt_insert_entries;
+	vm->cleanup = dpt_cleanup;
+
+	vm->vma_ops.bind_vma    = dpt_bind_vma;
+	vm->vma_ops.unbind_vma  = dpt_unbind_vma;
+	vm->vma_ops.set_pages   = ggtt_set_pages;
+	vm->vma_ops.clear_pages = clear_pages;
+
+	vm->pte_encode = gen8_ggtt_pte_encode;
+
+	dpt->obj = dpt_obj;
+
+	return &dpt->vm;
+}
+
+void intel_dpt_destroy(struct i915_address_space *vm)
+{
+	struct i915_dpt *dpt = i915_vm_to_dpt(vm);
+
+	i915_vm_close(&dpt->vm);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dpt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dpt.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright © 2021 Intel Corporation
+ */
+
+#ifndef __INTEL_DPT_H__
+#define __INTEL_DPT_H__
+
+struct i915_address_space;
+struct i915_vma;
+struct intel_framebuffer;
+
+void intel_dpt_destroy(struct i915_address_space *vm);
+struct i915_vma *intel_dpt_pin(struct i915_address_space *vm);
+void intel_dpt_unpin(struct i915_address_space *vm);
+struct i915_address_space *
+intel_dpt_create(struct intel_framebuffer *fb);
+
+#endif /* __INTEL_DPT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_drrs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_drrs.c
@@ -0,0 +1,485 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright © 2021 Intel Corporation
+ */
+
+#include "i915_drv.h"
+#include "intel_atomic.h"
+#include "intel_de.h"
+#include "intel_display_types.h"
+#include "intel_drrs.h"
+#include "intel_panel.h"
+
+/**
+ * DOC: Display Refresh Rate Switching (DRRS)
+ *
+ * Display Refresh Rate Switching (DRRS) is a power conservation feature
+ * which enables swtching between low and high refresh rates,
+ * dynamically, based on the usage scenario. This feature is applicable
+ * for internal panels.
+ *
+ * Indication that the panel supports DRRS is given by the panel EDID, which
+ * would list multiple refresh rates for one resolution.
+ *
+ * DRRS is of 2 types - static and seamless.
+ * Static DRRS involves changing refresh rate (RR) by doing a full modeset
+ * (may appear as a blink on screen) and is used in dock-undock scenario.
+ * Seamless DRRS involves changing RR without any visual effect to the user
+ * and can be used during normal system usage. This is done by programming
+ * certain registers.
+ *
+ * Support for static/seamless DRRS may be indicated in the VBT based on
+ * inputs from the panel spec.
+ *
+ * DRRS saves power by switching to low RR based on usage scenarios.
+ *
+ * The implementation is based on frontbuffer tracking implementation.  When
+ * there is a disturbance on the screen triggered by user activity or a periodic
+ * system activity, DRRS is disabled (RR is changed to high RR).  When there is
+ * no movement on screen, after a timeout of 1 second, a switch to low RR is
+ * made.
+ *
+ * For integration with frontbuffer tracking code, intel_edp_drrs_invalidate()
+ * and intel_edp_drrs_flush() are called.
+ *
+ * DRRS can be further extended to support other internal panels and also
+ * the scenario of video playback wherein RR is set based on the rate
+ * requested by userspace.
+ */
+
+void
+intel_dp_drrs_compute_config(struct intel_dp *intel_dp,
+			     struct intel_crtc_state *pipe_config,
+			     int output_bpp, bool constant_n)
+{
+	struct intel_connector *intel_connector = intel_dp->attached_connector;
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+	int pixel_clock;
+
+	if (pipe_config->vrr.enable)
+		return;
+
+	/*
+	 * DRRS and PSR can't be enable together, so giving preference to PSR
+	 * as it allows more power-savings by complete shutting down display,
+	 * so to guarantee this, intel_dp_drrs_compute_config() must be called
+	 * after intel_psr_compute_config().
+	 */
+	if (pipe_config->has_psr)
+		return;
+
+	if (!intel_connector->panel.downclock_mode ||
+	    dev_priv->drrs.type != SEAMLESS_DRRS_SUPPORT)
+		return;
+
+	pipe_config->has_drrs = true;
+
+	pixel_clock = intel_connector->panel.downclock_mode->clock;
+	if (pipe_config->splitter.enable)
+		pixel_clock /= pipe_config->splitter.link_count;
+
+	intel_link_compute_m_n(output_bpp, pipe_config->lane_count, pixel_clock,
+			       pipe_config->port_clock, &pipe_config->dp_m2_n2,
+			       constant_n, pipe_config->fec_enable);
+
+	/* FIXME: abstract this better */
+	if (pipe_config->splitter.enable)
+		pipe_config->dp_m2_n2.gmch_m *= pipe_config->splitter.link_count;
+}
+
+/**
+ * intel_dp_set_drrs_state - program registers for RR switch to take effect
+ * @dev_priv: i915 device
+ * @crtc_state: a pointer to the active intel_crtc_state
+ * @refresh_rate: RR to be programmed
+ *
+ * This function gets called when refresh rate (RR) has to be changed from
+ * one frequency to another. Switches can be between high and low RR
+ * supported by the panel or to any other RR based on media playback (in
+ * this case, RR value needs to be passed from user space).
+ *
+ * The caller of this function needs to take a lock on dev_priv->drrs.
+ */
+static void intel_dp_set_drrs_state(struct drm_i915_private *dev_priv,
+				    const struct intel_crtc_state *crtc_state,
+				    int refresh_rate)
+{
+	struct intel_dp *intel_dp = dev_priv->drrs.dp;
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
+	enum drrs_refresh_rate_type index = DRRS_HIGH_RR;
+
+	if (refresh_rate <= 0) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "Refresh rate should be positive non-zero.\n");
+		return;
+	}
+
+	if (intel_dp == NULL) {
+		drm_dbg_kms(&dev_priv->drm, "DRRS not supported.\n");
+		return;
+	}
+
+	if (!crtc) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "DRRS: intel_crtc not initialized\n");
+		return;
+	}
+
+	if (dev_priv->drrs.type < SEAMLESS_DRRS_SUPPORT) {
+		drm_dbg_kms(&dev_priv->drm, "Only Seamless DRRS supported.\n");
+		return;
+	}
+
+	if (drm_mode_vrefresh(intel_dp->attached_connector->panel.downclock_mode) ==
+			refresh_rate)
+		index = DRRS_LOW_RR;
+
+	if (index == dev_priv->drrs.refresh_rate_type) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "DRRS requested for previously set RR...ignoring\n");
+		return;
+	}
+
+	if (!crtc_state->hw.active) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "eDP encoder disabled. CRTC not Active\n");
+		return;
+	}
+
+	if (DISPLAY_VER(dev_priv) >= 8 && !IS_CHERRYVIEW(dev_priv)) {
+		switch (index) {
+		case DRRS_HIGH_RR:
+			intel_dp_set_m_n(crtc_state, M1_N1);
+			break;
+		case DRRS_LOW_RR:
+			intel_dp_set_m_n(crtc_state, M2_N2);
+			break;
+		case DRRS_MAX_RR:
+		default:
+			drm_err(&dev_priv->drm,
+				"Unsupported refreshrate type\n");
+		}
+	} else if (DISPLAY_VER(dev_priv) > 6) {
+		i915_reg_t reg = PIPECONF(crtc_state->cpu_transcoder);
+		u32 val;
+
+		val = intel_de_read(dev_priv, reg);
+		if (index > DRRS_HIGH_RR) {
+			if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
+				val |= PIPECONF_EDP_RR_MODE_SWITCH_VLV;
+			else
+				val |= PIPECONF_EDP_RR_MODE_SWITCH;
+		} else {
+			if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
+				val &= ~PIPECONF_EDP_RR_MODE_SWITCH_VLV;
+			else
+				val &= ~PIPECONF_EDP_RR_MODE_SWITCH;
+		}
+		intel_de_write(dev_priv, reg, val);
+	}
+
+	dev_priv->drrs.refresh_rate_type = index;
+
+	drm_dbg_kms(&dev_priv->drm, "eDP Refresh Rate set to : %dHz\n",
+		    refresh_rate);
+}
+
+static void
+intel_edp_drrs_enable_locked(struct intel_dp *intel_dp)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	dev_priv->drrs.busy_frontbuffer_bits = 0;
+	dev_priv->drrs.dp = intel_dp;
+}
+
+/**
+ * intel_edp_drrs_enable - init drrs struct if supported
+ * @intel_dp: DP struct
+ * @crtc_state: A pointer to the active crtc state.
+ *
+ * Initializes frontbuffer_bits and drrs.dp
+ */
+void intel_edp_drrs_enable(struct intel_dp *intel_dp,
+			   const struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	if (!crtc_state->has_drrs)
+		return;
+
+	drm_dbg_kms(&dev_priv->drm, "Enabling DRRS\n");
+
+	mutex_lock(&dev_priv->drrs.mutex);
+
+	if (dev_priv->drrs.dp) {
+		drm_warn(&dev_priv->drm, "DRRS already enabled\n");
+		goto unlock;
+	}
+
+	intel_edp_drrs_enable_locked(intel_dp);
+
+unlock:
+	mutex_unlock(&dev_priv->drrs.mutex);
+}
+
+static void
+intel_edp_drrs_disable_locked(struct intel_dp *intel_dp,
+			      const struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	if (dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR) {
+		int refresh;
+
+		refresh = drm_mode_vrefresh(intel_dp->attached_connector->panel.fixed_mode);
+		intel_dp_set_drrs_state(dev_priv, crtc_state, refresh);
+	}
+
+	dev_priv->drrs.dp = NULL;
+}
+
+/**
+ * intel_edp_drrs_disable - Disable DRRS
+ * @intel_dp: DP struct
+ * @old_crtc_state: Pointer to old crtc_state.
+ *
+ */
+void intel_edp_drrs_disable(struct intel_dp *intel_dp,
+			    const struct intel_crtc_state *old_crtc_state)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	if (!old_crtc_state->has_drrs)
+		return;
+
+	mutex_lock(&dev_priv->drrs.mutex);
+	if (!dev_priv->drrs.dp) {
+		mutex_unlock(&dev_priv->drrs.mutex);
+		return;
+	}
+
+	intel_edp_drrs_disable_locked(intel_dp, old_crtc_state);
+	mutex_unlock(&dev_priv->drrs.mutex);
+
+	cancel_delayed_work_sync(&dev_priv->drrs.work);
+}
+
+/**
+ * intel_edp_drrs_update - Update DRRS state
+ * @intel_dp: Intel DP
+ * @crtc_state: new CRTC state
+ *
+ * This function will update DRRS states, disabling or enabling DRRS when
+ * executing fastsets. For full modeset, intel_edp_drrs_disable() and
+ * intel_edp_drrs_enable() should be called instead.
+ */
+void
+intel_edp_drrs_update(struct intel_dp *intel_dp,
+		      const struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	if (dev_priv->drrs.type != SEAMLESS_DRRS_SUPPORT)
+		return;
+
+	mutex_lock(&dev_priv->drrs.mutex);
+
+	/* New state matches current one? */
+	if (crtc_state->has_drrs == !!dev_priv->drrs.dp)
+		goto unlock;
+
+	if (crtc_state->has_drrs)
+		intel_edp_drrs_enable_locked(intel_dp);
+	else
+		intel_edp_drrs_disable_locked(intel_dp, crtc_state);
+
+unlock:
+	mutex_unlock(&dev_priv->drrs.mutex);
+}
+
+static void intel_edp_drrs_downclock_work(struct work_struct *work)
+{
+	struct drm_i915_private *dev_priv =
+		container_of(work, typeof(*dev_priv), drrs.work.work);
+	struct intel_dp *intel_dp;
+
+	mutex_lock(&dev_priv->drrs.mutex);
+
+	intel_dp = dev_priv->drrs.dp;
+
+	if (!intel_dp)
+		goto unlock;
+
+	/*
+	 * The delayed work can race with an invalidate hence we need to
+	 * recheck.
+	 */
+
+	if (dev_priv->drrs.busy_frontbuffer_bits)
+		goto unlock;
+
+	if (dev_priv->drrs.refresh_rate_type != DRRS_LOW_RR) {
+		struct drm_crtc *crtc = dp_to_dig_port(intel_dp)->base.base.crtc;
+
+		intel_dp_set_drrs_state(dev_priv, to_intel_crtc(crtc)->config,
+					drm_mode_vrefresh(intel_dp->attached_connector->panel.downclock_mode));
+	}
+
+unlock:
+	mutex_unlock(&dev_priv->drrs.mutex);
+}
+
+/**
+ * intel_edp_drrs_invalidate - Disable Idleness DRRS
+ * @dev_priv: i915 device
+ * @frontbuffer_bits: frontbuffer plane tracking bits
+ *
+ * This function gets called everytime rendering on the given planes start.
+ * Hence DRRS needs to be Upclocked, i.e. (LOW_RR -> HIGH_RR).
+ *
+ * Dirty frontbuffers relevant to DRRS are tracked in busy_frontbuffer_bits.
+ */
+void intel_edp_drrs_invalidate(struct drm_i915_private *dev_priv,
+			       unsigned int frontbuffer_bits)
+{
+	struct intel_dp *intel_dp;
+	struct drm_crtc *crtc;
+	enum pipe pipe;
+
+	if (dev_priv->drrs.type == DRRS_NOT_SUPPORTED)
+		return;
+
+	cancel_delayed_work(&dev_priv->drrs.work);
+
+	mutex_lock(&dev_priv->drrs.mutex);
+
+	intel_dp = dev_priv->drrs.dp;
+	if (!intel_dp) {
+		mutex_unlock(&dev_priv->drrs.mutex);
+		return;
+	}
+
+	crtc = dp_to_dig_port(intel_dp)->base.base.crtc;
+	pipe = to_intel_crtc(crtc)->pipe;
+
+	frontbuffer_bits &= INTEL_FRONTBUFFER_ALL_MASK(pipe);
+	dev_priv->drrs.busy_frontbuffer_bits |= frontbuffer_bits;
+
+	/* invalidate means busy screen hence upclock */
+	if (frontbuffer_bits && dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR)
+		intel_dp_set_drrs_state(dev_priv, to_intel_crtc(crtc)->config,
+					drm_mode_vrefresh(intel_dp->attached_connector->panel.fixed_mode));
+
+	mutex_unlock(&dev_priv->drrs.mutex);
+}
+
+/**
+ * intel_edp_drrs_flush - Restart Idleness DRRS
+ * @dev_priv: i915 device
+ * @frontbuffer_bits: frontbuffer plane tracking bits
+ *
+ * This function gets called every time rendering on the given planes has
+ * completed or flip on a crtc is completed. So DRRS should be upclocked
+ * (LOW_RR -> HIGH_RR). And also Idleness detection should be started again,
+ * if no other planes are dirty.
+ *
+ * Dirty frontbuffers relevant to DRRS are tracked in busy_frontbuffer_bits.
+ */
+void intel_edp_drrs_flush(struct drm_i915_private *dev_priv,
+			  unsigned int frontbuffer_bits)
+{
+	struct intel_dp *intel_dp;
+	struct drm_crtc *crtc;
+	enum pipe pipe;
+
+	if (dev_priv->drrs.type == DRRS_NOT_SUPPORTED)
+		return;
+
+	cancel_delayed_work(&dev_priv->drrs.work);
+
+	mutex_lock(&dev_priv->drrs.mutex);
+
+	intel_dp = dev_priv->drrs.dp;
+	if (!intel_dp) {
+		mutex_unlock(&dev_priv->drrs.mutex);
+		return;
+	}
+
+	crtc = dp_to_dig_port(intel_dp)->base.base.crtc;
+	pipe = to_intel_crtc(crtc)->pipe;
+
+	frontbuffer_bits &= INTEL_FRONTBUFFER_ALL_MASK(pipe);
+	dev_priv->drrs.busy_frontbuffer_bits &= ~frontbuffer_bits;
+
+	/* flush means busy screen hence upclock */
+	if (frontbuffer_bits && dev_priv->drrs.refresh_rate_type == DRRS_LOW_RR)
+		intel_dp_set_drrs_state(dev_priv, to_intel_crtc(crtc)->config,
+					drm_mode_vrefresh(intel_dp->attached_connector->panel.fixed_mode));
+
+	/*
+	 * flush also means no more activity hence schedule downclock, if all
+	 * other fbs are quiescent too
+	 */
+	if (!dev_priv->drrs.busy_frontbuffer_bits)
+		schedule_delayed_work(&dev_priv->drrs.work,
+				      msecs_to_jiffies(1000));
+	mutex_unlock(&dev_priv->drrs.mutex);
+}
+
+/**
+ * intel_dp_drrs_init - Init basic DRRS work and mutex.
+ * @connector: eDP connector
+ * @fixed_mode: preferred mode of panel
+ *
+ * This function is  called only once at driver load to initialize basic
+ * DRRS stuff.
+ *
+ * Returns:
+ * Downclock mode if panel supports it, else return NULL.
+ * DRRS support is determined by the presence of downclock mode (apart
+ * from VBT setting).
+ */
+struct drm_display_mode *
+intel_dp_drrs_init(struct intel_connector *connector,
+		   struct drm_display_mode *fixed_mode)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_encoder *encoder = connector->encoder;
+	struct drm_display_mode *downclock_mode = NULL;
+
+	INIT_DELAYED_WORK(&dev_priv->drrs.work, intel_edp_drrs_downclock_work);
+	mutex_init(&dev_priv->drrs.mutex);
+
+	if (DISPLAY_VER(dev_priv) <= 6) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "DRRS supported for Gen7 and above\n");
+		return NULL;
+	}
+
+	if ((DISPLAY_VER(dev_priv) < 8 && !HAS_GMCH(dev_priv)) &&
+	    encoder->port != PORT_A) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "DRRS only supported on eDP port A\n");
+		return NULL;
+	}
+
+	if (dev_priv->vbt.drrs_type != SEAMLESS_DRRS_SUPPORT) {
+		drm_dbg_kms(&dev_priv->drm, "VBT doesn't support DRRS\n");
+		return NULL;
+	}
+
+	downclock_mode = intel_panel_edid_downclock_mode(connector, fixed_mode);
+	if (!downclock_mode) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "Downclock mode is not found. DRRS not supported\n");
+		return NULL;
+	}
+
+	dev_priv->drrs.type = dev_priv->vbt.drrs_type;
+
+	dev_priv->drrs.refresh_rate_type = DRRS_HIGH_RR;
+	drm_dbg_kms(&dev_priv->drm,
+		    "seamless DRRS supported for eDP panel.\n");
+	return downclock_mode;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_drrs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_drrs.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright © 2021 Intel Corporation
+ */
+
+#ifndef __INTEL_DRRS_H__
+#define __INTEL_DRRS_H__
+
+#include <linux/types.h>
+
+struct drm_i915_private;
+struct intel_crtc_state;
+struct intel_connector;
+struct intel_dp;
+
+void intel_edp_drrs_enable(struct intel_dp *intel_dp,
+			   const struct intel_crtc_state *crtc_state);
+void intel_edp_drrs_disable(struct intel_dp *intel_dp,
+			    const struct intel_crtc_state *crtc_state);
+void intel_edp_drrs_update(struct intel_dp *intel_dp,
+			   const struct intel_crtc_state *crtc_state);
+void intel_edp_drrs_invalidate(struct drm_i915_private *dev_priv,
+			       unsigned int frontbuffer_bits);
+void intel_edp_drrs_flush(struct drm_i915_private *dev_priv,
+			  unsigned int frontbuffer_bits);
+void intel_dp_drrs_compute_config(struct intel_dp *intel_dp,
+				  struct intel_crtc_state *pipe_config,
+				  int output_bpp, bool constant_n);
+struct drm_display_mode *intel_dp_drrs_init(struct intel_connector *connector,
+					    struct drm_display_mode *fixed_mode);
+
+#endif /* __INTEL_DRRS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dsb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dsb.c
@@ -100,7 +100,7 @@
 	u32 reg_val;
 
 	if (!dsb) {
-		intel_de_write(dev_priv, reg, val);
+		intel_de_write_fw(dev_priv, reg, val);
 		return;
 	}
 	buf = dsb->cmd_buf;
@@ -177,7 +177,7 @@
 
 	dsb = crtc_state->dsb;
 	if (!dsb) {
-		intel_de_write(dev_priv, reg, val);
+		intel_de_write_fw(dev_priv, reg, val);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dsi_vbt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dsi_vbt.c
@@ -121,9 +121,25 @@
 #define  ICL_GPIO_DDPA_CTRLCLK_2	8
 #define  ICL_GPIO_DDPA_CTRLDATA_2	9
 
-static enum port intel_dsi_seq_port_to_port(u8 port)
+static enum port intel_dsi_seq_port_to_port(struct intel_dsi *intel_dsi,
+					    u8 seq_port)
 {
-	return port ? PORT_C : PORT_A;
+	/*
+	 * If single link DSI is being used on any port, the VBT sequence block
+	 * send packet apparently always has 0 for the port. Just use the port
+	 * we have configured, and ignore the sequence block port.
+	 */
+	if (hweight8(intel_dsi->ports) == 1)
+		return ffs(intel_dsi->ports) - 1;
+
+	if (seq_port) {
+		if (intel_dsi->ports & BIT(PORT_B))
+			return PORT_B;
+		else if (intel_dsi->ports & BIT(PORT_C))
+			return PORT_C;
+	}
+
+	return PORT_A;
 }
 
 static const u8 *mipi_exec_send_packet(struct intel_dsi *intel_dsi,
@@ -145,15 +161,10 @@
 
 	seq_port = (flags >> MIPI_PORT_SHIFT) & 3;
 
-	/* For DSI single link on Port A & C, the seq_port value which is
-	 * parsed from Sequence Block#53 of VBT has been set to 0
-	 * Now, read/write of packets for the DSI single link on Port A and
-	 * Port C will based on the DVO port from VBT block 2.
-	 */
-	if (intel_dsi->ports == (1 << PORT_C))
-		port = PORT_C;
-	else
-		port = intel_dsi_seq_port_to_port(seq_port);
+	port = intel_dsi_seq_port_to_port(intel_dsi, seq_port);
+
+	if (drm_WARN_ON(&dev_priv->drm, !intel_dsi->dsi_hosts[port]))
+		goto out;
 
 	dsi_device = intel_dsi->dsi_hosts[port]->device;
 	if (!dsi_device) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_dvo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_dvo.c
@@ -220,14 +220,20 @@
 }
 
 static enum drm_mode_status
-intel_dvo_mode_valid(struct drm_connector *connector,
+intel_dvo_mode_valid(struct drm_connector *_connector,
 		     struct drm_display_mode *mode)
 {
-	struct intel_dvo *intel_dvo = intel_attached_dvo(to_intel_connector(connector));
-	const struct drm_display_mode *fixed_mode =
-		to_intel_connector(connector)->panel.fixed_mode;
-	int max_dotclk = to_i915(connector->dev)->max_dotclk_freq;
+	struct intel_connector *connector = to_intel_connector(_connector);
+	struct drm_i915_private *i915 = to_i915(connector->base.dev);
+	struct intel_dvo *intel_dvo = intel_attached_dvo(connector);
+	const struct drm_display_mode *fixed_mode = connector->panel.fixed_mode;
+	int max_dotclk = i915->max_dotclk_freq;
 	int target_clock = mode->clock;
+	enum drm_mode_status status;
+
+	status = intel_cpu_transcoder_mode_valid(i915, mode);
+	if (status != MODE_OK)
+		return status;
 
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return MODE_NO_DBLESCAN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_fb.c
@@ -172,8 +172,9 @@
 
 	intel_fb_plane_get_subsampling(&main_hsub, &main_vsub, &fb->base, main_plane);
 	intel_fb_plane_get_subsampling(&hsub, &vsub, &fb->base, color_plane);
-	*w = fb->base.width / main_hsub / hsub;
-	*h = fb->base.height / main_vsub / vsub;
+
+	*w = DIV_ROUND_UP(fb->base.width, main_hsub * hsub);
+	*h = DIV_ROUND_UP(fb->base.height, main_vsub * vsub);
 }
 
 static u32 intel_adjust_tile_offset(int *x, int *y,
@@ -794,7 +795,7 @@
 		 * arithmetic related to alignment and offset calculation.
 		 */
 		if (is_gen12_ccs_cc_plane(&fb->base, i)) {
-			if (IS_ALIGNED(fb->base.offsets[i], PAGE_SIZE))
+			if (IS_ALIGNED(fb->base.offsets[i], 64))
 				continue;
 			else
 				return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_fbc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_fbc.c
@@ -1129,7 +1129,7 @@
 	if (!HAS_FBC(dev_priv))
 		return;
 
-	if (origin == ORIGIN_GTT || origin == ORIGIN_FLIP)
+	if (origin == ORIGIN_FLIP || origin == ORIGIN_CURSOR_UPDATE)
 		return;
 
 	mutex_lock(&fbc->lock);
@@ -1150,19 +1150,11 @@
 	if (!HAS_FBC(dev_priv))
 		return;
 
-	/*
-	 * GTT tracking does not nuke the entire cfb
-	 * so don't clear busy_bits set for some other
-	 * reason.
-	 */
-	if (origin == ORIGIN_GTT)
-		return;
-
 	mutex_lock(&fbc->lock);
 
 	fbc->busy_bits &= ~frontbuffer_bits;
 
-	if (origin == ORIGIN_FLIP)
+	if (origin == ORIGIN_FLIP || origin == ORIGIN_CURSOR_UPDATE)
 		goto out;
 
 	if (!fbc->busy_bits && fbc->crtc &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_fbdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_fbdev.c
@@ -229,8 +229,6 @@
 		goto out_unlock;
 	}
 
-	intel_frontbuffer_flush(to_frontbuffer(ifbdev), ORIGIN_DIRTYFB);
-
 	info = drm_fb_helper_alloc_fbi(helper);
 	if (IS_ERR(info)) {
 		drm_err(&dev_priv->drm, "Failed to allocate fb_info\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_frontbuffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_frontbuffer.c
@@ -62,6 +62,7 @@
 #include "intel_display_types.h"
 #include "intel_fbc.h"
 #include "intel_frontbuffer.h"
+#include "intel_drrs.h"
 #include "intel_psr.h"
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_frontbuffer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_frontbuffer.h
@@ -33,11 +33,11 @@
 struct drm_i915_private;
 
 enum fb_op_origin {
-	ORIGIN_GTT,
-	ORIGIN_CPU,
+	ORIGIN_CPU = 0,
 	ORIGIN_CS,
 	ORIGIN_FLIP,
 	ORIGIN_DIRTYFB,
+	ORIGIN_CURSOR_UPDATE,
 };
 
 struct intel_frontbuffer {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_gmbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_gmbus.c
@@ -334,6 +334,15 @@
 	algo->data = bus;
 }
 
+static bool has_gmbus_irq(struct drm_i915_private *i915)
+{
+	/*
+	 * encoder->shutdown() may want to use GMBUS
+	 * after irqs have already been disabled.
+	 */
+	return HAS_GMBUS_IRQ(i915) && intel_irqs_enabled(i915);
+}
+
 static int gmbus_wait(struct drm_i915_private *dev_priv, u32 status, u32 irq_en)
 {
 	DEFINE_WAIT(wait);
@@ -344,7 +353,7 @@
 	 * we also need to check for NAKs besides the hw ready/idle signal, we
 	 * need to wake up periodically and check that ourselves.
 	 */
-	if (!HAS_GMBUS_IRQ(dev_priv))
+	if (!has_gmbus_irq(dev_priv))
 		irq_en = 0;
 
 	add_wait_queue(&dev_priv->gmbus_wait_queue, &wait);
@@ -375,7 +384,7 @@
 
 	/* Important: The hw handles only the first bit, so set only one! */
 	irq_enable = 0;
-	if (HAS_GMBUS_IRQ(dev_priv))
+	if (has_gmbus_irq(dev_priv))
 		irq_enable = GMBUS_IDLE_EN;
 
 	add_wait_queue(&dev_priv->gmbus_wait_queue, &wait);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_hdmi.c
@@ -53,21 +53,20 @@
 #include "intel_panel.h"
 #include "intel_snps_phy.h"
 
-static struct drm_device *intel_hdmi_to_dev(struct intel_hdmi *intel_hdmi)
+static struct drm_i915_private *intel_hdmi_to_i915(struct intel_hdmi *intel_hdmi)
 {
-	return hdmi_to_dig_port(intel_hdmi)->base.base.dev;
+	return to_i915(hdmi_to_dig_port(intel_hdmi)->base.base.dev);
 }
 
 static void
 assert_hdmi_port_disabled(struct intel_hdmi *intel_hdmi)
 {
-	struct drm_device *dev = intel_hdmi_to_dev(intel_hdmi);
-	struct drm_i915_private *dev_priv = to_i915(dev);
+	struct drm_i915_private *dev_priv = intel_hdmi_to_i915(intel_hdmi);
 	u32 enabled_bits;
 
 	enabled_bits = HAS_DDI(dev_priv) ? DDI_BUF_CTL_ENABLE : SDVO_ENABLE;
 
-	drm_WARN(dev,
+	drm_WARN(&dev_priv->drm,
 		 intel_de_read(dev_priv, intel_hdmi->hdmi_reg) & enabled_bits,
 		 "HDMI port enabled, expecting disabled\n");
 }
@@ -1246,13 +1245,14 @@
 
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable)
 {
-	struct drm_i915_private *dev_priv = to_i915(intel_hdmi_to_dev(hdmi));
-	struct i2c_adapter *adapter =
-		intel_gmbus_get_adapter(dev_priv, hdmi->ddc_bus);
+	struct drm_i915_private *dev_priv = intel_hdmi_to_i915(hdmi);
+	struct i2c_adapter *adapter;
 
 	if (hdmi->dp_dual_mode.type < DRM_DP_DUAL_MODE_TYPE2_DVI)
 		return;
 
+	adapter = intel_gmbus_get_adapter(dev_priv, hdmi->ddc_bus);
+
 	drm_dbg_kms(&dev_priv->drm, "%s DP dual mode adaptor TMDS output\n",
 		    enable ? "Enabling" : "Disabling");
 
@@ -1830,7 +1830,8 @@
 		      int clock, bool respect_downstream_limits,
 		      bool has_hdmi_sink)
 {
-	struct drm_i915_private *dev_priv = to_i915(intel_hdmi_to_dev(hdmi));
+	struct drm_i915_private *dev_priv = intel_hdmi_to_i915(hdmi);
+	enum phy phy = intel_port_to_phy(dev_priv, hdmi_to_dig_port(hdmi)->base.port);
 
 	if (clock < 25000)
 		return MODE_CLOCK_LOW;
@@ -1851,6 +1852,14 @@
 	if (IS_CHERRYVIEW(dev_priv) && clock > 216000 && clock < 240000)
 		return MODE_CLOCK_RANGE;
 
+	/* ICL+ combo PHY PLL can't generate 500-533.2 MHz */
+	if (intel_phy_is_combo(dev_priv, phy) && clock > 500000 && clock < 533200)
+		return MODE_CLOCK_RANGE;
+
+	/* ICL+ TC PHY PLL can't generate 500-532.8 MHz */
+	if (intel_phy_is_tc(dev_priv, phy) && clock > 500000 && clock < 532800)
+		return MODE_CLOCK_RANGE;
+
 	/*
 	 * SNPS PHYs' MPLLB table-based programming can only handle a fixed
 	 * set of link rates.
@@ -1892,7 +1901,7 @@
 		if (ycbcr420_output)
 			return hdmi->y420_dc_modes & DRM_EDID_YCBCR420_DC_36;
 		else
-			return info->edid_hdmi_dc_modes & DRM_EDID_HDMI_DC_36;
+			return info->edid_hdmi_rgb444_dc_modes & DRM_EDID_HDMI_DC_36;
 	case 10:
 		if (DISPLAY_VER(i915) < 11)
 			return false;
@@ -1903,7 +1912,7 @@
 		if (ycbcr420_output)
 			return hdmi->y420_dc_modes & DRM_EDID_YCBCR420_DC_30;
 		else
-			return info->edid_hdmi_dc_modes & DRM_EDID_HDMI_DC_30;
+			return info->edid_hdmi_rgb444_dc_modes & DRM_EDID_HDMI_DC_30;
 	case 8:
 		return true;
 	default:
@@ -1946,16 +1955,16 @@
 		      struct drm_display_mode *mode)
 {
 	struct intel_hdmi *hdmi = intel_attached_hdmi(to_intel_connector(connector));
-	struct drm_device *dev = intel_hdmi_to_dev(hdmi);
-	struct drm_i915_private *dev_priv = to_i915(dev);
+	struct drm_i915_private *dev_priv = intel_hdmi_to_i915(hdmi);
 	enum drm_mode_status status;
 	int clock = mode->clock;
 	int max_dotclk = to_i915(connector->dev)->max_dotclk_freq;
 	bool has_hdmi_sink = intel_has_hdmi_sink(hdmi, connector->state);
 	bool ycbcr_420_only;
 
-	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
-		return MODE_NO_DBLESCAN;
+	status = intel_cpu_transcoder_mode_valid(dev_priv, mode);
+	if (status != MODE_OK)
+		return status;
 
 	if ((mode->flags & DRM_MODE_FLAG_3D_MASK) == DRM_MODE_FLAG_3D_FRAME_PACKING)
 		clock *= 2;
@@ -2189,6 +2198,10 @@
 	if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return -EINVAL;
 
+	if (!connector->interlace_allowed &&
+	    adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE)
+		return -EINVAL;
+
 	pipe_config->output_format = INTEL_OUTPUT_FORMAT_RGB;
 	pipe_config->has_hdmi_sink = intel_has_hdmi_sink(intel_hdmi,
 							 conn_state);
@@ -2260,6 +2273,17 @@
 	return 0;
 }
 
+void intel_hdmi_encoder_shutdown(struct intel_encoder *encoder)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(encoder);
+
+	/*
+	 * Give a hand to buggy BIOSen which forget to turn
+	 * the TMDS output buffers back on after a reboot.
+	 */
+	intel_dp_dual_mode_set_tmds_output(intel_hdmi, true);
+}
+
 static void
 intel_hdmi_unset_edid(struct drm_connector *connector)
 {
@@ -2869,9 +2893,12 @@
 				    ddc);
 	drm_connector_helper_add(connector, &intel_hdmi_connector_helper_funcs);
 
-	connector->interlace_allowed = 1;
+	if (DISPLAY_VER(dev_priv) < 12)
+		connector->interlace_allowed = true;
+
 	connector->doublescan_allowed = 0;
-	connector->stereo_allowed = 1;
+
+	connector->stereo_allowed = true;
 
 	if (DISPLAY_VER(dev_priv) >= 10)
 		connector->ycbcr_420_allowed = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_hdmi.h
@@ -28,6 +28,7 @@
 int intel_hdmi_compute_config(struct intel_encoder *encoder,
 			      struct intel_crtc_state *pipe_config,
 			      struct drm_connector_state *conn_state);
+void intel_hdmi_encoder_shutdown(struct intel_encoder *encoder);
 bool intel_hdmi_handle_sink_scrambling(struct intel_encoder *encoder,
 				       struct drm_connector *connector,
 				       bool high_tmds_clock_ratio,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_lpe_audio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_lpe_audio.c
@@ -175,6 +175,14 @@
 				handle_simple_irq,
 				"hdmi_lpe_audio_irq_handler");
 
+	static const struct pci_device_id irq_quirk_ids[] = {
+		/* Dell Wyse 3040 */
+		{PCI_DEVICE_SUB(PCI_VENDOR_ID_INTEL, 0x22b0, 0x1028, 0x07c1)},
+		{}
+	};
+
+	if (pci_dev_present(irq_quirk_ids))
+		return 0;
 	return irq_set_chip_data(irq, dev_priv);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_lvds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_lvds.c
@@ -40,6 +40,7 @@
 
 #include "i915_drv.h"
 #include "intel_atomic.h"
+#include "intel_backlight.h"
 #include "intel_connector.h"
 #include "intel_de.h"
 #include "intel_display_types.h"
@@ -386,8 +387,14 @@
 		      struct drm_display_mode *mode)
 {
 	struct intel_connector *intel_connector = to_intel_connector(connector);
+	struct drm_i915_private *i915 = to_i915(intel_connector->base.dev);
 	struct drm_display_mode *fixed_mode = intel_connector->panel.fixed_mode;
-	int max_pixclk = to_i915(connector->dev)->max_dotclk_freq;
+	int max_pixclk = i915->max_dotclk_freq;
+	enum drm_mode_status status;
+
+	status = intel_cpu_transcoder_mode_valid(i915, mode);
+	if (status != MODE_OK)
+		return status;
 
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return MODE_NO_DBLESCAN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_opregion.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_opregion.c
@@ -30,10 +30,9 @@
 #include <linux/firmware.h>
 #include <acpi/video.h>
 
-#include "display/intel_panel.h"
-
 #include "i915_drv.h"
 #include "intel_acpi.h"
+#include "intel_backlight.h"
 #include "intel_display_types.h"
 #include "intel_opregion.h"
 
@@ -361,6 +360,21 @@
 		port++;
 	}
 
+	/*
+	 * The port numbering and mapping here is bizarre. The now-obsolete
+	 * swsci spec supports ports numbered [0..4]. Port E is handled as a
+	 * special case, but port F and beyond are not. The functionality is
+	 * supposed to be obsolete for new platforms. Just bail out if the port
+	 * number is out of bounds after mapping.
+	 */
+	if (port > 4) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "[ENCODER:%d:%s] port %c (index %u) out of bounds for display power state notification\n",
+			    intel_encoder->base.base.id, intel_encoder->base.name,
+			    port_name(intel_encoder->port), port);
+		return -EINVAL;
+	}
+
 	if (!enable)
 		parm |= 4 << 8;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_overlay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_overlay.c
@@ -959,6 +959,9 @@
 	const struct intel_crtc_state *pipe_config =
 		overlay->crtc->config;
 
+	if (rec->dst_height == 0 || rec->dst_width == 0)
+		return -EINVAL;
+
 	if (rec->dst_x < pipe_config->pipe_src_w &&
 	    rec->dst_x + rec->dst_width <= pipe_config->pipe_src_w &&
 	    rec->dst_y < pipe_config->pipe_src_h &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_panel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_panel.c
@@ -28,17 +28,13 @@
  *      Chris Wilson <chris@chris-wilson.co.uk>
  */
 
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
 #include <linux/kernel.h>
-#include <linux/moduleparam.h>
 #include <linux/pwm.h>
 
+#include "intel_backlight.h"
 #include "intel_connector.h"
 #include "intel_de.h"
 #include "intel_display_types.h"
-#include "intel_dp_aux_backlight.h"
-#include "intel_dsi_dcs_backlight.h"
 #include "intel_panel.h"
 
 void
@@ -456,1767 +452,6 @@
 	return 0;
 }
 
-/**
- * scale - scale values from one range to another
- * @source_val: value in range [@source_min..@source_max]
- * @source_min: minimum legal value for @source_val
- * @source_max: maximum legal value for @source_val
- * @target_min: corresponding target value for @source_min
- * @target_max: corresponding target value for @source_max
- *
- * Return @source_val in range [@source_min..@source_max] scaled to range
- * [@target_min..@target_max].
- */
-static u32 scale(u32 source_val,
-		 u32 source_min, u32 source_max,
-		 u32 target_min, u32 target_max)
-{
-	u64 target_val;
-
-	WARN_ON(source_min > source_max);
-	WARN_ON(target_min > target_max);
-
-	/* defensive */
-	source_val = clamp(source_val, source_min, source_max);
-
-	/* avoid overflows */
-	target_val = mul_u32_u32(source_val - source_min,
-				 target_max - target_min);
-	target_val = DIV_ROUND_CLOSEST_ULL(target_val, source_max - source_min);
-	target_val += target_min;
-
-	return target_val;
-}
-
-/* Scale user_level in range [0..user_max] to [0..hw_max], clamping the result
- * to [hw_min..hw_max]. */
-static u32 clamp_user_to_hw(struct intel_connector *connector,
-			    u32 user_level, u32 user_max)
-{
-	struct intel_panel *panel = &connector->panel;
-	u32 hw_level;
-
-	hw_level = scale(user_level, 0, user_max, 0, panel->backlight.max);
-	hw_level = clamp(hw_level, panel->backlight.min, panel->backlight.max);
-
-	return hw_level;
-}
-
-/* Scale hw_level in range [hw_min..hw_max] to [0..user_max]. */
-static u32 scale_hw_to_user(struct intel_connector *connector,
-			    u32 hw_level, u32 user_max)
-{
-	struct intel_panel *panel = &connector->panel;
-
-	return scale(hw_level, panel->backlight.min, panel->backlight.max,
-		     0, user_max);
-}
-
-u32 intel_panel_invert_pwm_level(struct intel_connector *connector, u32 val)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	drm_WARN_ON(&dev_priv->drm, panel->backlight.pwm_level_max == 0);
-
-	if (dev_priv->params.invert_brightness < 0)
-		return val;
-
-	if (dev_priv->params.invert_brightness > 0 ||
-	    dev_priv->quirks & QUIRK_INVERT_BRIGHTNESS) {
-		return panel->backlight.pwm_level_max - val + panel->backlight.pwm_level_min;
-	}
-
-	return val;
-}
-
-void intel_panel_set_pwm_level(const struct drm_connector_state *conn_state, u32 val)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *i915 = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	drm_dbg_kms(&i915->drm, "set backlight PWM = %d\n", val);
-	panel->backlight.pwm_funcs->set(conn_state, val);
-}
-
-u32 intel_panel_backlight_level_to_pwm(struct intel_connector *connector, u32 val)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	drm_WARN_ON_ONCE(&dev_priv->drm,
-			 panel->backlight.max == 0 || panel->backlight.pwm_level_max == 0);
-
-	val = scale(val, panel->backlight.min, panel->backlight.max,
-		    panel->backlight.pwm_level_min, panel->backlight.pwm_level_max);
-
-	return intel_panel_invert_pwm_level(connector, val);
-}
-
-u32 intel_panel_backlight_level_from_pwm(struct intel_connector *connector, u32 val)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	drm_WARN_ON_ONCE(&dev_priv->drm,
-			 panel->backlight.max == 0 || panel->backlight.pwm_level_max == 0);
-
-	if (dev_priv->params.invert_brightness > 0 ||
-	    (dev_priv->params.invert_brightness == 0 && dev_priv->quirks & QUIRK_INVERT_BRIGHTNESS))
-		val = panel->backlight.pwm_level_max - (val - panel->backlight.pwm_level_min);
-
-	return scale(val, panel->backlight.pwm_level_min, panel->backlight.pwm_level_max,
-		     panel->backlight.min, panel->backlight.max);
-}
-
-static u32 lpt_get_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	return intel_de_read(dev_priv, BLC_PWM_PCH_CTL2) & BACKLIGHT_DUTY_CYCLE_MASK;
-}
-
-static u32 pch_get_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	return intel_de_read(dev_priv, BLC_PWM_CPU_CTL) & BACKLIGHT_DUTY_CYCLE_MASK;
-}
-
-static u32 i9xx_get_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 val;
-
-	val = intel_de_read(dev_priv, BLC_PWM_CTL) & BACKLIGHT_DUTY_CYCLE_MASK;
-	if (DISPLAY_VER(dev_priv) < 4)
-		val >>= 1;
-
-	if (panel->backlight.combination_mode) {
-		u8 lbpc;
-
-		pci_read_config_byte(to_pci_dev(dev_priv->drm.dev), LBPC, &lbpc);
-		val *= lbpc;
-	}
-
-	return val;
-}
-
-static u32 vlv_get_backlight(struct intel_connector *connector, enum pipe pipe)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	if (drm_WARN_ON(&dev_priv->drm, pipe != PIPE_A && pipe != PIPE_B))
-		return 0;
-
-	return intel_de_read(dev_priv, VLV_BLC_PWM_CTL(pipe)) & BACKLIGHT_DUTY_CYCLE_MASK;
-}
-
-static u32 bxt_get_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	return intel_de_read(dev_priv,
-			     BXT_BLC_PWM_DUTY(panel->backlight.controller));
-}
-
-static u32 ext_pwm_get_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct intel_panel *panel = &connector->panel;
-	struct pwm_state state;
-
-	pwm_get_state(panel->backlight.pwm, &state);
-	return pwm_get_relative_duty_cycle(&state, 100);
-}
-
-static void lpt_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	u32 val = intel_de_read(dev_priv, BLC_PWM_PCH_CTL2) & ~BACKLIGHT_DUTY_CYCLE_MASK;
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL2, val | level);
-}
-
-static void pch_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	u32 tmp;
-
-	tmp = intel_de_read(dev_priv, BLC_PWM_CPU_CTL) & ~BACKLIGHT_DUTY_CYCLE_MASK;
-	intel_de_write(dev_priv, BLC_PWM_CPU_CTL, tmp | level);
-}
-
-static void i9xx_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 tmp, mask;
-
-	drm_WARN_ON(&dev_priv->drm, panel->backlight.pwm_level_max == 0);
-
-	if (panel->backlight.combination_mode) {
-		u8 lbpc;
-
-		lbpc = level * 0xfe / panel->backlight.pwm_level_max + 1;
-		level /= lbpc;
-		pci_write_config_byte(to_pci_dev(dev_priv->drm.dev), LBPC, lbpc);
-	}
-
-	if (DISPLAY_VER(dev_priv) == 4) {
-		mask = BACKLIGHT_DUTY_CYCLE_MASK;
-	} else {
-		level <<= 1;
-		mask = BACKLIGHT_DUTY_CYCLE_MASK_PNV;
-	}
-
-	tmp = intel_de_read(dev_priv, BLC_PWM_CTL) & ~mask;
-	intel_de_write(dev_priv, BLC_PWM_CTL, tmp | level);
-}
-
-static void vlv_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	enum pipe pipe = to_intel_crtc(conn_state->crtc)->pipe;
-	u32 tmp;
-
-	tmp = intel_de_read(dev_priv, VLV_BLC_PWM_CTL(pipe)) & ~BACKLIGHT_DUTY_CYCLE_MASK;
-	intel_de_write(dev_priv, VLV_BLC_PWM_CTL(pipe), tmp | level);
-}
-
-static void bxt_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	intel_de_write(dev_priv,
-		       BXT_BLC_PWM_DUTY(panel->backlight.controller), level);
-}
-
-static void ext_pwm_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_panel *panel = &to_intel_connector(conn_state->connector)->panel;
-
-	pwm_set_relative_duty_cycle(&panel->backlight.pwm_state, level, 100);
-	pwm_apply_state(panel->backlight.pwm, &panel->backlight.pwm_state);
-}
-
-static void
-intel_panel_actually_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *i915 = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	drm_dbg_kms(&i915->drm, "set backlight level = %d\n", level);
-
-	panel->backlight.funcs->set(conn_state, level);
-}
-
-/* set backlight brightness to level in range [0..max], assuming hw min is
- * respected.
- */
-void intel_panel_set_backlight_acpi(const struct drm_connector_state *conn_state,
-				    u32 user_level, u32 user_max)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 hw_level;
-
-	/*
-	 * Lack of crtc may occur during driver init because
-	 * connection_mutex isn't held across the entire backlight
-	 * setup + modeset readout, and the BIOS can issue the
-	 * requests at any time.
-	 */
-	if (!panel->backlight.present || !conn_state->crtc)
-		return;
-
-	mutex_lock(&dev_priv->backlight_lock);
-
-	drm_WARN_ON(&dev_priv->drm, panel->backlight.max == 0);
-
-	hw_level = clamp_user_to_hw(connector, user_level, user_max);
-	panel->backlight.level = hw_level;
-
-	if (panel->backlight.device)
-		panel->backlight.device->props.brightness =
-			scale_hw_to_user(connector,
-					 panel->backlight.level,
-					 panel->backlight.device->props.max_brightness);
-
-	if (panel->backlight.enabled)
-		intel_panel_actually_set_backlight(conn_state, hw_level);
-
-	mutex_unlock(&dev_priv->backlight_lock);
-}
-
-static void lpt_disable_backlight(const struct drm_connector_state *old_conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	u32 tmp;
-
-	intel_panel_set_pwm_level(old_conn_state, level);
-
-	/*
-	 * Although we don't support or enable CPU PWM with LPT/SPT based
-	 * systems, it may have been enabled prior to loading the
-	 * driver. Disable to avoid warnings on LCPLL disable.
-	 *
-	 * This needs rework if we need to add support for CPU PWM on PCH split
-	 * platforms.
-	 */
-	tmp = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
-	if (tmp & BLM_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "cpu backlight was enabled, disabling\n");
-		intel_de_write(dev_priv, BLC_PWM_CPU_CTL2,
-			       tmp & ~BLM_PWM_ENABLE);
-	}
-
-	tmp = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, tmp & ~BLM_PCH_PWM_ENABLE);
-}
-
-static void pch_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	u32 tmp;
-
-	intel_panel_set_pwm_level(old_conn_state, val);
-
-	tmp = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
-	intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, tmp & ~BLM_PWM_ENABLE);
-
-	tmp = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, tmp & ~BLM_PCH_PWM_ENABLE);
-}
-
-static void i9xx_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
-{
-	intel_panel_set_pwm_level(old_conn_state, val);
-}
-
-static void i965_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
-{
-	struct drm_i915_private *dev_priv = to_i915(old_conn_state->connector->dev);
-	u32 tmp;
-
-	intel_panel_set_pwm_level(old_conn_state, val);
-
-	tmp = intel_de_read(dev_priv, BLC_PWM_CTL2);
-	intel_de_write(dev_priv, BLC_PWM_CTL2, tmp & ~BLM_PWM_ENABLE);
-}
-
-static void vlv_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	enum pipe pipe = to_intel_crtc(old_conn_state->crtc)->pipe;
-	u32 tmp;
-
-	intel_panel_set_pwm_level(old_conn_state, val);
-
-	tmp = intel_de_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
-	intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe),
-		       tmp & ~BLM_PWM_ENABLE);
-}
-
-static void bxt_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 tmp;
-
-	intel_panel_set_pwm_level(old_conn_state, val);
-
-	tmp = intel_de_read(dev_priv,
-			    BXT_BLC_PWM_CTL(panel->backlight.controller));
-	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
-		       tmp & ~BXT_BLC_PWM_ENABLE);
-
-	if (panel->backlight.controller == 1) {
-		val = intel_de_read(dev_priv, UTIL_PIN_CTL);
-		val &= ~UTIL_PIN_ENABLE;
-		intel_de_write(dev_priv, UTIL_PIN_CTL, val);
-	}
-}
-
-static void cnp_disable_backlight(const struct drm_connector_state *old_conn_state, u32 val)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 tmp;
-
-	intel_panel_set_pwm_level(old_conn_state, val);
-
-	tmp = intel_de_read(dev_priv,
-			    BXT_BLC_PWM_CTL(panel->backlight.controller));
-	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
-		       tmp & ~BXT_BLC_PWM_ENABLE);
-}
-
-static void ext_pwm_disable_backlight(const struct drm_connector_state *old_conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct intel_panel *panel = &connector->panel;
-
-	panel->backlight.pwm_state.enabled = false;
-	pwm_apply_state(panel->backlight.pwm, &panel->backlight.pwm_state);
-}
-
-void intel_panel_disable_backlight(const struct drm_connector_state *old_conn_state)
-{
-	struct intel_connector *connector = to_intel_connector(old_conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	if (!panel->backlight.present)
-		return;
-
-	/*
-	 * Do not disable backlight on the vga_switcheroo path. When switching
-	 * away from i915, the other client may depend on i915 to handle the
-	 * backlight. This will leave the backlight on unnecessarily when
-	 * another client is not activated.
-	 */
-	if (dev_priv->drm.switch_power_state == DRM_SWITCH_POWER_CHANGING) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "Skipping backlight disable on vga switch\n");
-		return;
-	}
-
-	mutex_lock(&dev_priv->backlight_lock);
-
-	if (panel->backlight.device)
-		panel->backlight.device->props.power = FB_BLANK_POWERDOWN;
-	panel->backlight.enabled = false;
-	panel->backlight.funcs->disable(old_conn_state, 0);
-
-	mutex_unlock(&dev_priv->backlight_lock);
-}
-
-static void lpt_enable_backlight(const struct intel_crtc_state *crtc_state,
-				 const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 pch_ctl1, pch_ctl2, schicken;
-
-	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
-	if (pch_ctl1 & BLM_PCH_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "pch backlight already enabled\n");
-		pch_ctl1 &= ~BLM_PCH_PWM_ENABLE;
-		intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
-	}
-
-	if (HAS_PCH_LPT(dev_priv)) {
-		schicken = intel_de_read(dev_priv, SOUTH_CHICKEN2);
-		if (panel->backlight.alternate_pwm_increment)
-			schicken |= LPT_PWM_GRANULARITY;
-		else
-			schicken &= ~LPT_PWM_GRANULARITY;
-		intel_de_write(dev_priv, SOUTH_CHICKEN2, schicken);
-	} else {
-		schicken = intel_de_read(dev_priv, SOUTH_CHICKEN1);
-		if (panel->backlight.alternate_pwm_increment)
-			schicken |= SPT_PWM_GRANULARITY;
-		else
-			schicken &= ~SPT_PWM_GRANULARITY;
-		intel_de_write(dev_priv, SOUTH_CHICKEN1, schicken);
-	}
-
-	pch_ctl2 = panel->backlight.pwm_level_max << 16;
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL2, pch_ctl2);
-
-	pch_ctl1 = 0;
-	if (panel->backlight.active_low_pwm)
-		pch_ctl1 |= BLM_PCH_POLARITY;
-
-	/* After LPT, override is the default. */
-	if (HAS_PCH_LPT(dev_priv))
-		pch_ctl1 |= BLM_PCH_OVERRIDE_ENABLE;
-
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
-	intel_de_posting_read(dev_priv, BLC_PWM_PCH_CTL1);
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1,
-		       pch_ctl1 | BLM_PCH_PWM_ENABLE);
-
-	/* This won't stick until the above enable. */
-	intel_panel_set_pwm_level(conn_state, level);
-}
-
-static void pch_enable_backlight(const struct intel_crtc_state *crtc_state,
-				 const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
-	u32 cpu_ctl2, pch_ctl1, pch_ctl2;
-
-	cpu_ctl2 = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
-	if (cpu_ctl2 & BLM_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "cpu backlight already enabled\n");
-		cpu_ctl2 &= ~BLM_PWM_ENABLE;
-		intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, cpu_ctl2);
-	}
-
-	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
-	if (pch_ctl1 & BLM_PCH_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "pch backlight already enabled\n");
-		pch_ctl1 &= ~BLM_PCH_PWM_ENABLE;
-		intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
-	}
-
-	if (cpu_transcoder == TRANSCODER_EDP)
-		cpu_ctl2 = BLM_TRANSCODER_EDP;
-	else
-		cpu_ctl2 = BLM_PIPE(cpu_transcoder);
-	intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, cpu_ctl2);
-	intel_de_posting_read(dev_priv, BLC_PWM_CPU_CTL2);
-	intel_de_write(dev_priv, BLC_PWM_CPU_CTL2, cpu_ctl2 | BLM_PWM_ENABLE);
-
-	/* This won't stick until the above enable. */
-	intel_panel_set_pwm_level(conn_state, level);
-
-	pch_ctl2 = panel->backlight.pwm_level_max << 16;
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL2, pch_ctl2);
-
-	pch_ctl1 = 0;
-	if (panel->backlight.active_low_pwm)
-		pch_ctl1 |= BLM_PCH_POLARITY;
-
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1, pch_ctl1);
-	intel_de_posting_read(dev_priv, BLC_PWM_PCH_CTL1);
-	intel_de_write(dev_priv, BLC_PWM_PCH_CTL1,
-		       pch_ctl1 | BLM_PCH_PWM_ENABLE);
-}
-
-static void i9xx_enable_backlight(const struct intel_crtc_state *crtc_state,
-				  const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 ctl, freq;
-
-	ctl = intel_de_read(dev_priv, BLC_PWM_CTL);
-	if (ctl & BACKLIGHT_DUTY_CYCLE_MASK_PNV) {
-		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
-		intel_de_write(dev_priv, BLC_PWM_CTL, 0);
-	}
-
-	freq = panel->backlight.pwm_level_max;
-	if (panel->backlight.combination_mode)
-		freq /= 0xff;
-
-	ctl = freq << 17;
-	if (panel->backlight.combination_mode)
-		ctl |= BLM_LEGACY_MODE;
-	if (IS_PINEVIEW(dev_priv) && panel->backlight.active_low_pwm)
-		ctl |= BLM_POLARITY_PNV;
-
-	intel_de_write(dev_priv, BLC_PWM_CTL, ctl);
-	intel_de_posting_read(dev_priv, BLC_PWM_CTL);
-
-	/* XXX: combine this into above write? */
-	intel_panel_set_pwm_level(conn_state, level);
-
-	/*
-	 * Needed to enable backlight on some 855gm models. BLC_HIST_CTL is
-	 * 855gm only, but checking for gen2 is safe, as 855gm is the only gen2
-	 * that has backlight.
-	 */
-	if (DISPLAY_VER(dev_priv) == 2)
-		intel_de_write(dev_priv, BLC_HIST_CTL, BLM_HISTOGRAM_ENABLE);
-}
-
-static void i965_enable_backlight(const struct intel_crtc_state *crtc_state,
-				  const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	enum pipe pipe = to_intel_crtc(conn_state->crtc)->pipe;
-	u32 ctl, ctl2, freq;
-
-	ctl2 = intel_de_read(dev_priv, BLC_PWM_CTL2);
-	if (ctl2 & BLM_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
-		ctl2 &= ~BLM_PWM_ENABLE;
-		intel_de_write(dev_priv, BLC_PWM_CTL2, ctl2);
-	}
-
-	freq = panel->backlight.pwm_level_max;
-	if (panel->backlight.combination_mode)
-		freq /= 0xff;
-
-	ctl = freq << 16;
-	intel_de_write(dev_priv, BLC_PWM_CTL, ctl);
-
-	ctl2 = BLM_PIPE(pipe);
-	if (panel->backlight.combination_mode)
-		ctl2 |= BLM_COMBINATION_MODE;
-	if (panel->backlight.active_low_pwm)
-		ctl2 |= BLM_POLARITY_I965;
-	intel_de_write(dev_priv, BLC_PWM_CTL2, ctl2);
-	intel_de_posting_read(dev_priv, BLC_PWM_CTL2);
-	intel_de_write(dev_priv, BLC_PWM_CTL2, ctl2 | BLM_PWM_ENABLE);
-
-	intel_panel_set_pwm_level(conn_state, level);
-}
-
-static void vlv_enable_backlight(const struct intel_crtc_state *crtc_state,
-				 const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	enum pipe pipe = to_intel_crtc(crtc_state->uapi.crtc)->pipe;
-	u32 ctl, ctl2;
-
-	ctl2 = intel_de_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
-	if (ctl2 & BLM_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
-		ctl2 &= ~BLM_PWM_ENABLE;
-		intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe), ctl2);
-	}
-
-	ctl = panel->backlight.pwm_level_max << 16;
-	intel_de_write(dev_priv, VLV_BLC_PWM_CTL(pipe), ctl);
-
-	/* XXX: combine this into above write? */
-	intel_panel_set_pwm_level(conn_state, level);
-
-	ctl2 = 0;
-	if (panel->backlight.active_low_pwm)
-		ctl2 |= BLM_POLARITY_I965;
-	intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe), ctl2);
-	intel_de_posting_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
-	intel_de_write(dev_priv, VLV_BLC_PWM_CTL2(pipe),
-		       ctl2 | BLM_PWM_ENABLE);
-}
-
-static void bxt_enable_backlight(const struct intel_crtc_state *crtc_state,
-				 const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	enum pipe pipe = to_intel_crtc(crtc_state->uapi.crtc)->pipe;
-	u32 pwm_ctl, val;
-
-	/* Controller 1 uses the utility pin. */
-	if (panel->backlight.controller == 1) {
-		val = intel_de_read(dev_priv, UTIL_PIN_CTL);
-		if (val & UTIL_PIN_ENABLE) {
-			drm_dbg_kms(&dev_priv->drm,
-				    "util pin already enabled\n");
-			val &= ~UTIL_PIN_ENABLE;
-			intel_de_write(dev_priv, UTIL_PIN_CTL, val);
-		}
-
-		val = 0;
-		if (panel->backlight.util_pin_active_low)
-			val |= UTIL_PIN_POLARITY;
-		intel_de_write(dev_priv, UTIL_PIN_CTL,
-			       val | UTIL_PIN_PIPE(pipe) | UTIL_PIN_MODE_PWM | UTIL_PIN_ENABLE);
-	}
-
-	pwm_ctl = intel_de_read(dev_priv,
-				BXT_BLC_PWM_CTL(panel->backlight.controller));
-	if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
-		pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
-		intel_de_write(dev_priv,
-			       BXT_BLC_PWM_CTL(panel->backlight.controller),
-			       pwm_ctl);
-	}
-
-	intel_de_write(dev_priv,
-		       BXT_BLC_PWM_FREQ(panel->backlight.controller),
-		       panel->backlight.pwm_level_max);
-
-	intel_panel_set_pwm_level(conn_state, level);
-
-	pwm_ctl = 0;
-	if (panel->backlight.active_low_pwm)
-		pwm_ctl |= BXT_BLC_PWM_POLARITY;
-
-	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
-		       pwm_ctl);
-	intel_de_posting_read(dev_priv,
-			      BXT_BLC_PWM_CTL(panel->backlight.controller));
-	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
-		       pwm_ctl | BXT_BLC_PWM_ENABLE);
-}
-
-static void cnp_enable_backlight(const struct intel_crtc_state *crtc_state,
-				 const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 pwm_ctl;
-
-	pwm_ctl = intel_de_read(dev_priv,
-				BXT_BLC_PWM_CTL(panel->backlight.controller));
-	if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
-		drm_dbg_kms(&dev_priv->drm, "backlight already enabled\n");
-		pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
-		intel_de_write(dev_priv,
-			       BXT_BLC_PWM_CTL(panel->backlight.controller),
-			       pwm_ctl);
-	}
-
-	intel_de_write(dev_priv,
-		       BXT_BLC_PWM_FREQ(panel->backlight.controller),
-		       panel->backlight.pwm_level_max);
-
-	intel_panel_set_pwm_level(conn_state, level);
-
-	pwm_ctl = 0;
-	if (panel->backlight.active_low_pwm)
-		pwm_ctl |= BXT_BLC_PWM_POLARITY;
-
-	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
-		       pwm_ctl);
-	intel_de_posting_read(dev_priv,
-			      BXT_BLC_PWM_CTL(panel->backlight.controller));
-	intel_de_write(dev_priv, BXT_BLC_PWM_CTL(panel->backlight.controller),
-		       pwm_ctl | BXT_BLC_PWM_ENABLE);
-}
-
-static void ext_pwm_enable_backlight(const struct intel_crtc_state *crtc_state,
-				     const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct intel_panel *panel = &connector->panel;
-
-	pwm_set_relative_duty_cycle(&panel->backlight.pwm_state, level, 100);
-	panel->backlight.pwm_state.enabled = true;
-	pwm_apply_state(panel->backlight.pwm, &panel->backlight.pwm_state);
-}
-
-static void __intel_panel_enable_backlight(const struct intel_crtc_state *crtc_state,
-					   const struct drm_connector_state *conn_state)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct intel_panel *panel = &connector->panel;
-
-	WARN_ON(panel->backlight.max == 0);
-
-	if (panel->backlight.level <= panel->backlight.min) {
-		panel->backlight.level = panel->backlight.max;
-		if (panel->backlight.device)
-			panel->backlight.device->props.brightness =
-				scale_hw_to_user(connector,
-						 panel->backlight.level,
-						 panel->backlight.device->props.max_brightness);
-	}
-
-	panel->backlight.funcs->enable(crtc_state, conn_state, panel->backlight.level);
-	panel->backlight.enabled = true;
-	if (panel->backlight.device)
-		panel->backlight.device->props.power = FB_BLANK_UNBLANK;
-}
-
-void intel_panel_enable_backlight(const struct intel_crtc_state *crtc_state,
-				  const struct drm_connector_state *conn_state)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	enum pipe pipe = to_intel_crtc(crtc_state->uapi.crtc)->pipe;
-
-	if (!panel->backlight.present)
-		return;
-
-	drm_dbg_kms(&dev_priv->drm, "pipe %c\n", pipe_name(pipe));
-
-	mutex_lock(&dev_priv->backlight_lock);
-
-	__intel_panel_enable_backlight(crtc_state, conn_state);
-
-	mutex_unlock(&dev_priv->backlight_lock);
-}
-
-#if IS_ENABLED(CONFIG_BACKLIGHT_CLASS_DEVICE)
-static u32 intel_panel_get_backlight(struct intel_connector *connector)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 val = 0;
-
-	mutex_lock(&dev_priv->backlight_lock);
-
-	if (panel->backlight.enabled)
-		val = panel->backlight.funcs->get(connector, intel_connector_get_pipe(connector));
-
-	mutex_unlock(&dev_priv->backlight_lock);
-
-	drm_dbg_kms(&dev_priv->drm, "get backlight PWM = %d\n", val);
-	return val;
-}
-
-/* Scale user_level in range [0..user_max] to [hw_min..hw_max]. */
-static u32 scale_user_to_hw(struct intel_connector *connector,
-			    u32 user_level, u32 user_max)
-{
-	struct intel_panel *panel = &connector->panel;
-
-	return scale(user_level, 0, user_max,
-		     panel->backlight.min, panel->backlight.max);
-}
-
-/* set backlight brightness to level in range [0..max], scaling wrt hw min */
-static void intel_panel_set_backlight(const struct drm_connector_state *conn_state,
-				      u32 user_level, u32 user_max)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 hw_level;
-
-	if (!panel->backlight.present)
-		return;
-
-	mutex_lock(&dev_priv->backlight_lock);
-
-	drm_WARN_ON(&dev_priv->drm, panel->backlight.max == 0);
-
-	hw_level = scale_user_to_hw(connector, user_level, user_max);
-	panel->backlight.level = hw_level;
-
-	if (panel->backlight.enabled)
-		intel_panel_actually_set_backlight(conn_state, hw_level);
-
-	mutex_unlock(&dev_priv->backlight_lock);
-}
-
-static int intel_backlight_device_update_status(struct backlight_device *bd)
-{
-	struct intel_connector *connector = bl_get_data(bd);
-	struct intel_panel *panel = &connector->panel;
-	struct drm_device *dev = connector->base.dev;
-
-	drm_modeset_lock(&dev->mode_config.connection_mutex, NULL);
-	DRM_DEBUG_KMS("updating intel_backlight, brightness=%d/%d\n",
-		      bd->props.brightness, bd->props.max_brightness);
-	intel_panel_set_backlight(connector->base.state, bd->props.brightness,
-				  bd->props.max_brightness);
-
-	/*
-	 * Allow flipping bl_power as a sub-state of enabled. Sadly the
-	 * backlight class device does not make it easy to to differentiate
-	 * between callbacks for brightness and bl_power, so our backlight_power
-	 * callback needs to take this into account.
-	 */
-	if (panel->backlight.enabled) {
-		if (panel->backlight.power) {
-			bool enable = bd->props.power == FB_BLANK_UNBLANK &&
-				bd->props.brightness != 0;
-			panel->backlight.power(connector, enable);
-		}
-	} else {
-		bd->props.power = FB_BLANK_POWERDOWN;
-	}
-
-	drm_modeset_unlock(&dev->mode_config.connection_mutex);
-	return 0;
-}
-
-static int intel_backlight_device_get_brightness(struct backlight_device *bd)
-{
-	struct intel_connector *connector = bl_get_data(bd);
-	struct drm_device *dev = connector->base.dev;
-	struct drm_i915_private *dev_priv = to_i915(dev);
-	intel_wakeref_t wakeref;
-	int ret = 0;
-
-	with_intel_runtime_pm(&dev_priv->runtime_pm, wakeref) {
-		u32 hw_level;
-
-		drm_modeset_lock(&dev->mode_config.connection_mutex, NULL);
-
-		hw_level = intel_panel_get_backlight(connector);
-		ret = scale_hw_to_user(connector,
-				       hw_level, bd->props.max_brightness);
-
-		drm_modeset_unlock(&dev->mode_config.connection_mutex);
-	}
-
-	return ret;
-}
-
-static const struct backlight_ops intel_backlight_device_ops = {
-	.update_status = intel_backlight_device_update_status,
-	.get_brightness = intel_backlight_device_get_brightness,
-};
-
-int intel_backlight_device_register(struct intel_connector *connector)
-{
-	struct drm_i915_private *i915 = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	struct backlight_properties props;
-	struct backlight_device *bd;
-	const char *name;
-	int ret = 0;
-
-	if (WARN_ON(panel->backlight.device))
-		return -ENODEV;
-
-	if (!panel->backlight.present)
-		return 0;
-
-	WARN_ON(panel->backlight.max == 0);
-
-	memset(&props, 0, sizeof(props));
-	props.type = BACKLIGHT_RAW;
-
-	/*
-	 * Note: Everything should work even if the backlight device max
-	 * presented to the userspace is arbitrarily chosen.
-	 */
-	props.max_brightness = panel->backlight.max;
-	props.brightness = scale_hw_to_user(connector,
-					    panel->backlight.level,
-					    props.max_brightness);
-
-	if (panel->backlight.enabled)
-		props.power = FB_BLANK_UNBLANK;
-	else
-		props.power = FB_BLANK_POWERDOWN;
-
-	name = kstrdup("intel_backlight", GFP_KERNEL);
-	if (!name)
-		return -ENOMEM;
-
-	bd = backlight_device_register(name, connector->base.kdev, connector,
-				       &intel_backlight_device_ops, &props);
-
-	/*
-	 * Using the same name independent of the drm device or connector
-	 * prevents registration of multiple backlight devices in the
-	 * driver. However, we need to use the default name for backward
-	 * compatibility. Use unique names for subsequent backlight devices as a
-	 * fallback when the default name already exists.
-	 */
-	if (IS_ERR(bd) && PTR_ERR(bd) == -EEXIST) {
-		kfree(name);
-		name = kasprintf(GFP_KERNEL, "card%d-%s-backlight",
-				 i915->drm.primary->index, connector->base.name);
-		if (!name)
-			return -ENOMEM;
-
-		bd = backlight_device_register(name, connector->base.kdev, connector,
-					       &intel_backlight_device_ops, &props);
-	}
-
-	if (IS_ERR(bd)) {
-		drm_err(&i915->drm,
-			"[CONNECTOR:%d:%s] backlight device %s register failed: %ld\n",
-			connector->base.base.id, connector->base.name, name, PTR_ERR(bd));
-		ret = PTR_ERR(bd);
-		goto out;
-	}
-
-	panel->backlight.device = bd;
-
-	drm_dbg_kms(&i915->drm,
-		    "[CONNECTOR:%d:%s] backlight device %s registered\n",
-		    connector->base.base.id, connector->base.name, name);
-
-out:
-	kfree(name);
-
-	return ret;
-}
-
-void intel_backlight_device_unregister(struct intel_connector *connector)
-{
-	struct intel_panel *panel = &connector->panel;
-
-	if (panel->backlight.device) {
-		backlight_device_unregister(panel->backlight.device);
-		panel->backlight.device = NULL;
-	}
-}
-#endif /* CONFIG_BACKLIGHT_CLASS_DEVICE */
-
-/*
- * CNP: PWM clock frequency is 19.2 MHz or 24 MHz.
- *      PWM increment = 1
- */
-static u32 cnp_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	return DIV_ROUND_CLOSEST(KHz(RUNTIME_INFO(dev_priv)->rawclk_freq),
-				 pwm_freq_hz);
-}
-
-/*
- * BXT: PWM clock frequency = 19.2 MHz.
- */
-static u32 bxt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	return DIV_ROUND_CLOSEST(KHz(19200), pwm_freq_hz);
-}
-
-/*
- * SPT: This value represents the period of the PWM stream in clock periods
- * multiplied by 16 (default increment) or 128 (alternate increment selected in
- * SCHICKEN_1 bit 0). PWM clock is 24 MHz.
- */
-static u32 spt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct intel_panel *panel = &connector->panel;
-	u32 mul;
-
-	if (panel->backlight.alternate_pwm_increment)
-		mul = 128;
-	else
-		mul = 16;
-
-	return DIV_ROUND_CLOSEST(MHz(24), pwm_freq_hz * mul);
-}
-
-/*
- * LPT: This value represents the period of the PWM stream in clock periods
- * multiplied by 128 (default increment) or 16 (alternate increment, selected in
- * LPT SOUTH_CHICKEN2 register bit 5).
- */
-static u32 lpt_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 mul, clock;
-
-	if (panel->backlight.alternate_pwm_increment)
-		mul = 16;
-	else
-		mul = 128;
-
-	if (HAS_PCH_LPT_H(dev_priv))
-		clock = MHz(135); /* LPT:H */
-	else
-		clock = MHz(24); /* LPT:LP */
-
-	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * mul);
-}
-
-/*
- * ILK/SNB/IVB: This value represents the period of the PWM stream in PCH
- * display raw clocks multiplied by 128.
- */
-static u32 pch_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	return DIV_ROUND_CLOSEST(KHz(RUNTIME_INFO(dev_priv)->rawclk_freq),
-				 pwm_freq_hz * 128);
-}
-
-/*
- * Gen2: This field determines the number of time base events (display core
- * clock frequency/32) in total for a complete cycle of modulated backlight
- * control.
- *
- * Gen3: A time base event equals the display core clock ([DevPNV] HRAW clock)
- * divided by 32.
- */
-static u32 i9xx_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	int clock;
-
-	if (IS_PINEVIEW(dev_priv))
-		clock = KHz(RUNTIME_INFO(dev_priv)->rawclk_freq);
-	else
-		clock = KHz(dev_priv->cdclk.hw.cdclk);
-
-	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * 32);
-}
-
-/*
- * Gen4: This value represents the period of the PWM stream in display core
- * clocks ([DevCTG] HRAW clocks) multiplied by 128.
- *
- */
-static u32 i965_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	int clock;
-
-	if (IS_G4X(dev_priv))
-		clock = KHz(RUNTIME_INFO(dev_priv)->rawclk_freq);
-	else
-		clock = KHz(dev_priv->cdclk.hw.cdclk);
-
-	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * 128);
-}
-
-/*
- * VLV: This value represents the period of the PWM stream in display core
- * clocks ([DevCTG] 200MHz HRAW clocks) multiplied by 128 or 25MHz S0IX clocks
- * multiplied by 16. CHV uses a 19.2MHz S0IX clock.
- */
-static u32 vlv_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	int mul, clock;
-
-	if ((intel_de_read(dev_priv, CBR1_VLV) & CBR_PWM_CLOCK_MUX_SELECT) == 0) {
-		if (IS_CHERRYVIEW(dev_priv))
-			clock = KHz(19200);
-		else
-			clock = MHz(25);
-		mul = 16;
-	} else {
-		clock = KHz(RUNTIME_INFO(dev_priv)->rawclk_freq);
-		mul = 128;
-	}
-
-	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * mul);
-}
-
-static u16 get_vbt_pwm_freq(struct drm_i915_private *dev_priv)
-{
-	u16 pwm_freq_hz = dev_priv->vbt.backlight.pwm_freq_hz;
-
-	if (pwm_freq_hz) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "VBT defined backlight frequency %u Hz\n",
-			    pwm_freq_hz);
-	} else {
-		pwm_freq_hz = 200;
-		drm_dbg_kms(&dev_priv->drm,
-			    "default backlight frequency %u Hz\n",
-			    pwm_freq_hz);
-	}
-
-	return pwm_freq_hz;
-}
-
-static u32 get_backlight_max_vbt(struct intel_connector *connector)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u16 pwm_freq_hz = get_vbt_pwm_freq(dev_priv);
-	u32 pwm;
-
-	if (!panel->backlight.pwm_funcs->hz_to_pwm) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "backlight frequency conversion not supported\n");
-		return 0;
-	}
-
-	pwm = panel->backlight.pwm_funcs->hz_to_pwm(connector, pwm_freq_hz);
-	if (!pwm) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "backlight frequency conversion failed\n");
-		return 0;
-	}
-
-	return pwm;
-}
-
-/*
- * Note: The setup hooks can't assume pipe is set!
- */
-static u32 get_backlight_min_vbt(struct intel_connector *connector)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	int min;
-
-	drm_WARN_ON(&dev_priv->drm, panel->backlight.pwm_level_max == 0);
-
-	/*
-	 * XXX: If the vbt value is 255, it makes min equal to max, which leads
-	 * to problems. There are such machines out there. Either our
-	 * interpretation is wrong or the vbt has bogus data. Or both. Safeguard
-	 * against this by letting the minimum be at most (arbitrarily chosen)
-	 * 25% of the max.
-	 */
-	min = clamp_t(int, dev_priv->vbt.backlight.min_brightness, 0, 64);
-	if (min != dev_priv->vbt.backlight.min_brightness) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "clamping VBT min backlight %d/255 to %d/255\n",
-			    dev_priv->vbt.backlight.min_brightness, min);
-	}
-
-	/* vbt value is a coefficient in range [0..255] */
-	return scale(min, 0, 255, 0, panel->backlight.pwm_level_max);
-}
-
-static int lpt_setup_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 cpu_ctl2, pch_ctl1, pch_ctl2, val;
-	bool alt, cpu_mode;
-
-	if (HAS_PCH_LPT(dev_priv))
-		alt = intel_de_read(dev_priv, SOUTH_CHICKEN2) & LPT_PWM_GRANULARITY;
-	else
-		alt = intel_de_read(dev_priv, SOUTH_CHICKEN1) & SPT_PWM_GRANULARITY;
-	panel->backlight.alternate_pwm_increment = alt;
-
-	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
-	panel->backlight.active_low_pwm = pch_ctl1 & BLM_PCH_POLARITY;
-
-	pch_ctl2 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL2);
-	panel->backlight.pwm_level_max = pch_ctl2 >> 16;
-
-	cpu_ctl2 = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
-
-	if (!panel->backlight.pwm_level_max)
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	panel->backlight.pwm_enabled = pch_ctl1 & BLM_PCH_PWM_ENABLE;
-
-	cpu_mode = panel->backlight.pwm_enabled && HAS_PCH_LPT(dev_priv) &&
-		   !(pch_ctl1 & BLM_PCH_OVERRIDE_ENABLE) &&
-		   (cpu_ctl2 & BLM_PWM_ENABLE);
-
-	if (cpu_mode) {
-		val = pch_get_backlight(connector, unused);
-
-		drm_dbg_kms(&dev_priv->drm,
-			    "CPU backlight register was enabled, switching to PCH override\n");
-
-		/* Write converted CPU PWM value to PCH override register */
-		lpt_set_backlight(connector->base.state, val);
-		intel_de_write(dev_priv, BLC_PWM_PCH_CTL1,
-			       pch_ctl1 | BLM_PCH_OVERRIDE_ENABLE);
-
-		intel_de_write(dev_priv, BLC_PWM_CPU_CTL2,
-			       cpu_ctl2 & ~BLM_PWM_ENABLE);
-	}
-
-	return 0;
-}
-
-static int pch_setup_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 cpu_ctl2, pch_ctl1, pch_ctl2;
-
-	pch_ctl1 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL1);
-	panel->backlight.active_low_pwm = pch_ctl1 & BLM_PCH_POLARITY;
-
-	pch_ctl2 = intel_de_read(dev_priv, BLC_PWM_PCH_CTL2);
-	panel->backlight.pwm_level_max = pch_ctl2 >> 16;
-
-	if (!panel->backlight.pwm_level_max)
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	cpu_ctl2 = intel_de_read(dev_priv, BLC_PWM_CPU_CTL2);
-	panel->backlight.pwm_enabled = (cpu_ctl2 & BLM_PWM_ENABLE) &&
-		(pch_ctl1 & BLM_PCH_PWM_ENABLE);
-
-	return 0;
-}
-
-static int i9xx_setup_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 ctl, val;
-
-	ctl = intel_de_read(dev_priv, BLC_PWM_CTL);
-
-	if (DISPLAY_VER(dev_priv) == 2 || IS_I915GM(dev_priv) || IS_I945GM(dev_priv))
-		panel->backlight.combination_mode = ctl & BLM_LEGACY_MODE;
-
-	if (IS_PINEVIEW(dev_priv))
-		panel->backlight.active_low_pwm = ctl & BLM_POLARITY_PNV;
-
-	panel->backlight.pwm_level_max = ctl >> 17;
-
-	if (!panel->backlight.pwm_level_max) {
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-		panel->backlight.pwm_level_max >>= 1;
-	}
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	if (panel->backlight.combination_mode)
-		panel->backlight.pwm_level_max *= 0xff;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	val = i9xx_get_backlight(connector, unused);
-	val = intel_panel_invert_pwm_level(connector, val);
-	val = clamp(val, panel->backlight.pwm_level_min, panel->backlight.pwm_level_max);
-
-	panel->backlight.pwm_enabled = val != 0;
-
-	return 0;
-}
-
-static int i965_setup_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 ctl, ctl2;
-
-	ctl2 = intel_de_read(dev_priv, BLC_PWM_CTL2);
-	panel->backlight.combination_mode = ctl2 & BLM_COMBINATION_MODE;
-	panel->backlight.active_low_pwm = ctl2 & BLM_POLARITY_I965;
-
-	ctl = intel_de_read(dev_priv, BLC_PWM_CTL);
-	panel->backlight.pwm_level_max = ctl >> 16;
-
-	if (!panel->backlight.pwm_level_max)
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	if (panel->backlight.combination_mode)
-		panel->backlight.pwm_level_max *= 0xff;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	panel->backlight.pwm_enabled = ctl2 & BLM_PWM_ENABLE;
-
-	return 0;
-}
-
-static int vlv_setup_backlight(struct intel_connector *connector, enum pipe pipe)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 ctl, ctl2;
-
-	if (drm_WARN_ON(&dev_priv->drm, pipe != PIPE_A && pipe != PIPE_B))
-		return -ENODEV;
-
-	ctl2 = intel_de_read(dev_priv, VLV_BLC_PWM_CTL2(pipe));
-	panel->backlight.active_low_pwm = ctl2 & BLM_POLARITY_I965;
-
-	ctl = intel_de_read(dev_priv, VLV_BLC_PWM_CTL(pipe));
-	panel->backlight.pwm_level_max = ctl >> 16;
-
-	if (!panel->backlight.pwm_level_max)
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	panel->backlight.pwm_enabled = ctl2 & BLM_PWM_ENABLE;
-
-	return 0;
-}
-
-static int
-bxt_setup_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 pwm_ctl, val;
-
-	panel->backlight.controller = dev_priv->vbt.backlight.controller;
-
-	pwm_ctl = intel_de_read(dev_priv,
-				BXT_BLC_PWM_CTL(panel->backlight.controller));
-
-	/* Controller 1 uses the utility pin. */
-	if (panel->backlight.controller == 1) {
-		val = intel_de_read(dev_priv, UTIL_PIN_CTL);
-		panel->backlight.util_pin_active_low =
-					val & UTIL_PIN_POLARITY;
-	}
-
-	panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
-	panel->backlight.pwm_level_max =
-		intel_de_read(dev_priv, BXT_BLC_PWM_FREQ(panel->backlight.controller));
-
-	if (!panel->backlight.pwm_level_max)
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	panel->backlight.pwm_enabled = pwm_ctl & BXT_BLC_PWM_ENABLE;
-
-	return 0;
-}
-
-static int
-cnp_setup_backlight(struct intel_connector *connector, enum pipe unused)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-	u32 pwm_ctl;
-
-	/*
-	 * CNP has the BXT implementation of backlight, but with only one
-	 * controller. TODO: ICP has multiple controllers but we only use
-	 * controller 0 for now.
-	 */
-	panel->backlight.controller = 0;
-
-	pwm_ctl = intel_de_read(dev_priv,
-				BXT_BLC_PWM_CTL(panel->backlight.controller));
-
-	panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
-	panel->backlight.pwm_level_max =
-		intel_de_read(dev_priv, BXT_BLC_PWM_FREQ(panel->backlight.controller));
-
-	if (!panel->backlight.pwm_level_max)
-		panel->backlight.pwm_level_max = get_backlight_max_vbt(connector);
-
-	if (!panel->backlight.pwm_level_max)
-		return -ENODEV;
-
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	panel->backlight.pwm_enabled = pwm_ctl & BXT_BLC_PWM_ENABLE;
-
-	return 0;
-}
-
-static int ext_pwm_setup_backlight(struct intel_connector *connector,
-				   enum pipe pipe)
-{
-	struct drm_device *dev = connector->base.dev;
-	struct drm_i915_private *dev_priv = to_i915(dev);
-	struct intel_panel *panel = &connector->panel;
-	const char *desc;
-	u32 level;
-
-	/* Get the right PWM chip for DSI backlight according to VBT */
-	if (dev_priv->vbt.dsi.config->pwm_blc == PPS_BLC_PMIC) {
-		panel->backlight.pwm = pwm_get(dev->dev, "pwm_pmic_backlight");
-		desc = "PMIC";
-	} else {
-		panel->backlight.pwm = pwm_get(dev->dev, "pwm_soc_backlight");
-		desc = "SoC";
-	}
-
-	if (IS_ERR(panel->backlight.pwm)) {
-		drm_err(&dev_priv->drm, "Failed to get the %s PWM chip\n",
-			desc);
-		panel->backlight.pwm = NULL;
-		return -ENODEV;
-	}
-
-	panel->backlight.pwm_level_max = 100; /* 100% */
-	panel->backlight.pwm_level_min = get_backlight_min_vbt(connector);
-
-	if (pwm_is_enabled(panel->backlight.pwm)) {
-		/* PWM is already enabled, use existing settings */
-		pwm_get_state(panel->backlight.pwm, &panel->backlight.pwm_state);
-
-		level = pwm_get_relative_duty_cycle(&panel->backlight.pwm_state,
-						    100);
-		level = intel_panel_invert_pwm_level(connector, level);
-		panel->backlight.pwm_enabled = true;
-
-		drm_dbg_kms(&dev_priv->drm, "PWM already enabled at freq %ld, VBT freq %d, level %d\n",
-			    NSEC_PER_SEC / (unsigned long)panel->backlight.pwm_state.period,
-			    get_vbt_pwm_freq(dev_priv), level);
-	} else {
-		/* Set period from VBT frequency, leave other settings at 0. */
-		panel->backlight.pwm_state.period =
-			NSEC_PER_SEC / get_vbt_pwm_freq(dev_priv);
-	}
-
-	drm_info(&dev_priv->drm, "Using %s PWM for LCD backlight control\n",
-		 desc);
-	return 0;
-}
-
-static void intel_pwm_set_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct intel_panel *panel = &connector->panel;
-
-	panel->backlight.pwm_funcs->set(conn_state,
-				       intel_panel_invert_pwm_level(connector, level));
-}
-
-static u32 intel_pwm_get_backlight(struct intel_connector *connector, enum pipe pipe)
-{
-	struct intel_panel *panel = &connector->panel;
-
-	return intel_panel_invert_pwm_level(connector,
-					    panel->backlight.pwm_funcs->get(connector, pipe));
-}
-
-static void intel_pwm_enable_backlight(const struct intel_crtc_state *crtc_state,
-				       const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct intel_panel *panel = &connector->panel;
-
-	panel->backlight.pwm_funcs->enable(crtc_state, conn_state,
-					   intel_panel_invert_pwm_level(connector, level));
-}
-
-static void intel_pwm_disable_backlight(const struct drm_connector_state *conn_state, u32 level)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct intel_panel *panel = &connector->panel;
-
-	panel->backlight.pwm_funcs->disable(conn_state,
-					    intel_panel_invert_pwm_level(connector, level));
-}
-
-static int intel_pwm_setup_backlight(struct intel_connector *connector, enum pipe pipe)
-{
-	struct intel_panel *panel = &connector->panel;
-	int ret = panel->backlight.pwm_funcs->setup(connector, pipe);
-
-	if (ret < 0)
-		return ret;
-
-	panel->backlight.min = panel->backlight.pwm_level_min;
-	panel->backlight.max = panel->backlight.pwm_level_max;
-	panel->backlight.level = intel_pwm_get_backlight(connector, pipe);
-	panel->backlight.enabled = panel->backlight.pwm_enabled;
-
-	return 0;
-}
-
-void intel_panel_update_backlight(struct intel_atomic_state *state,
-				  struct intel_encoder *encoder,
-				  const struct intel_crtc_state *crtc_state,
-				  const struct drm_connector_state *conn_state)
-{
-	struct intel_connector *connector = to_intel_connector(conn_state->connector);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
-
-	if (!panel->backlight.present)
-		return;
-
-	mutex_lock(&dev_priv->backlight_lock);
-	if (!panel->backlight.enabled)
-		__intel_panel_enable_backlight(crtc_state, conn_state);
-
-	mutex_unlock(&dev_priv->backlight_lock);
-}
-
-int intel_panel_setup_backlight(struct drm_connector *connector, enum pipe pipe)
-{
-	struct drm_i915_private *dev_priv = to_i915(connector->dev);
-	struct intel_connector *intel_connector = to_intel_connector(connector);
-	struct intel_panel *panel = &intel_connector->panel;
-	int ret;
-
-	if (!dev_priv->vbt.backlight.present) {
-		if (dev_priv->quirks & QUIRK_BACKLIGHT_PRESENT) {
-			drm_dbg_kms(&dev_priv->drm,
-				    "no backlight present per VBT, but present per quirk\n");
-		} else {
-			drm_dbg_kms(&dev_priv->drm,
-				    "no backlight present per VBT\n");
-			return 0;
-		}
-	}
-
-	/* ensure intel_panel has been initialized first */
-	if (drm_WARN_ON(&dev_priv->drm, !panel->backlight.funcs))
-		return -ENODEV;
-
-	/* set level and max in panel struct */
-	mutex_lock(&dev_priv->backlight_lock);
-	ret = panel->backlight.funcs->setup(intel_connector, pipe);
-	mutex_unlock(&dev_priv->backlight_lock);
-
-	if (ret) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "failed to setup backlight for connector %s\n",
-			    connector->name);
-		return ret;
-	}
-
-	panel->backlight.present = true;
-
-	drm_dbg_kms(&dev_priv->drm,
-		    "Connector %s backlight initialized, %s, brightness %u/%u\n",
-		    connector->name,
-		    enableddisabled(panel->backlight.enabled),
-		    panel->backlight.level, panel->backlight.max);
-
-	return 0;
-}
-
-static void intel_panel_destroy_backlight(struct intel_panel *panel)
-{
-	/* dispose of the pwm */
-	if (panel->backlight.pwm)
-		pwm_put(panel->backlight.pwm);
-
-	panel->backlight.present = false;
-}
-
-static const struct intel_panel_bl_funcs bxt_pwm_funcs = {
-	.setup = bxt_setup_backlight,
-	.enable = bxt_enable_backlight,
-	.disable = bxt_disable_backlight,
-	.set = bxt_set_backlight,
-	.get = bxt_get_backlight,
-	.hz_to_pwm = bxt_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs cnp_pwm_funcs = {
-	.setup = cnp_setup_backlight,
-	.enable = cnp_enable_backlight,
-	.disable = cnp_disable_backlight,
-	.set = bxt_set_backlight,
-	.get = bxt_get_backlight,
-	.hz_to_pwm = cnp_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs lpt_pwm_funcs = {
-	.setup = lpt_setup_backlight,
-	.enable = lpt_enable_backlight,
-	.disable = lpt_disable_backlight,
-	.set = lpt_set_backlight,
-	.get = lpt_get_backlight,
-	.hz_to_pwm = lpt_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs spt_pwm_funcs = {
-	.setup = lpt_setup_backlight,
-	.enable = lpt_enable_backlight,
-	.disable = lpt_disable_backlight,
-	.set = lpt_set_backlight,
-	.get = lpt_get_backlight,
-	.hz_to_pwm = spt_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs pch_pwm_funcs = {
-	.setup = pch_setup_backlight,
-	.enable = pch_enable_backlight,
-	.disable = pch_disable_backlight,
-	.set = pch_set_backlight,
-	.get = pch_get_backlight,
-	.hz_to_pwm = pch_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs ext_pwm_funcs = {
-	.setup = ext_pwm_setup_backlight,
-	.enable = ext_pwm_enable_backlight,
-	.disable = ext_pwm_disable_backlight,
-	.set = ext_pwm_set_backlight,
-	.get = ext_pwm_get_backlight,
-};
-
-static const struct intel_panel_bl_funcs vlv_pwm_funcs = {
-	.setup = vlv_setup_backlight,
-	.enable = vlv_enable_backlight,
-	.disable = vlv_disable_backlight,
-	.set = vlv_set_backlight,
-	.get = vlv_get_backlight,
-	.hz_to_pwm = vlv_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs i965_pwm_funcs = {
-	.setup = i965_setup_backlight,
-	.enable = i965_enable_backlight,
-	.disable = i965_disable_backlight,
-	.set = i9xx_set_backlight,
-	.get = i9xx_get_backlight,
-	.hz_to_pwm = i965_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs i9xx_pwm_funcs = {
-	.setup = i9xx_setup_backlight,
-	.enable = i9xx_enable_backlight,
-	.disable = i9xx_disable_backlight,
-	.set = i9xx_set_backlight,
-	.get = i9xx_get_backlight,
-	.hz_to_pwm = i9xx_hz_to_pwm,
-};
-
-static const struct intel_panel_bl_funcs pwm_bl_funcs = {
-	.setup = intel_pwm_setup_backlight,
-	.enable = intel_pwm_enable_backlight,
-	.disable = intel_pwm_disable_backlight,
-	.set = intel_pwm_set_backlight,
-	.get = intel_pwm_get_backlight,
-};
-
-/* Set up chip specific backlight functions */
-static void
-intel_panel_init_backlight_funcs(struct intel_panel *panel)
-{
-	struct intel_connector *connector =
-		container_of(panel, struct intel_connector, panel);
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-
-	if (connector->base.connector_type == DRM_MODE_CONNECTOR_DSI &&
-	    intel_dsi_dcs_init_backlight_funcs(connector) == 0)
-		return;
-
-	if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) {
-		panel->backlight.pwm_funcs = &bxt_pwm_funcs;
-	} else if (INTEL_PCH_TYPE(dev_priv) >= PCH_CNP) {
-		panel->backlight.pwm_funcs = &cnp_pwm_funcs;
-	} else if (INTEL_PCH_TYPE(dev_priv) >= PCH_LPT) {
-		if (HAS_PCH_LPT(dev_priv))
-			panel->backlight.pwm_funcs = &lpt_pwm_funcs;
-		else
-			panel->backlight.pwm_funcs = &spt_pwm_funcs;
-	} else if (HAS_PCH_SPLIT(dev_priv)) {
-		panel->backlight.pwm_funcs = &pch_pwm_funcs;
-	} else if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) {
-		if (connector->base.connector_type == DRM_MODE_CONNECTOR_DSI) {
-			panel->backlight.pwm_funcs = &ext_pwm_funcs;
-		} else {
-			panel->backlight.pwm_funcs = &vlv_pwm_funcs;
-		}
-	} else if (DISPLAY_VER(dev_priv) == 4) {
-		panel->backlight.pwm_funcs = &i965_pwm_funcs;
-	} else {
-		panel->backlight.pwm_funcs = &i9xx_pwm_funcs;
-	}
-
-	if (connector->base.connector_type == DRM_MODE_CONNECTOR_eDP &&
-	    intel_dp_aux_init_backlight_funcs(connector) == 0)
-		return;
-
-	/* We're using a standard PWM backlight interface */
-	panel->backlight.funcs = &pwm_bl_funcs;
-}
-
 enum drm_connector_status
 intel_panel_detect(struct drm_connector *connector, bool force)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_panel.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_panel.h
@@ -8,15 +8,13 @@
 
 #include <linux/types.h>
 
-#include "intel_display.h"
-
+enum drm_connector_status;
 struct drm_connector;
 struct drm_connector_state;
 struct drm_display_mode;
+struct drm_i915_private;
 struct intel_connector;
-struct intel_crtc;
 struct intel_crtc_state;
-struct intel_encoder;
 struct intel_panel;
 
 int intel_panel_init(struct intel_panel *panel,
@@ -31,17 +29,6 @@
 			    const struct drm_connector_state *conn_state);
 int intel_gmch_panel_fitting(struct intel_crtc_state *crtc_state,
 			     const struct drm_connector_state *conn_state);
-void intel_panel_set_backlight_acpi(const struct drm_connector_state *conn_state,
-				    u32 level, u32 max);
-int intel_panel_setup_backlight(struct drm_connector *connector,
-				enum pipe pipe);
-void intel_panel_enable_backlight(const struct intel_crtc_state *crtc_state,
-				  const struct drm_connector_state *conn_state);
-void intel_panel_update_backlight(struct intel_atomic_state *state,
-				  struct intel_encoder *encoder,
-				  const struct intel_crtc_state *crtc_state,
-				  const struct drm_connector_state *conn_state);
-void intel_panel_disable_backlight(const struct drm_connector_state *old_conn_state);
 struct drm_display_mode *
 intel_panel_edid_downclock_mode(struct intel_connector *connector,
 				const struct drm_display_mode *fixed_mode);
@@ -49,22 +36,5 @@
 intel_panel_edid_fixed_mode(struct intel_connector *connector);
 struct drm_display_mode *
 intel_panel_vbt_fixed_mode(struct intel_connector *connector);
-void intel_panel_set_pwm_level(const struct drm_connector_state *conn_state, u32 level);
-u32 intel_panel_invert_pwm_level(struct intel_connector *connector, u32 level);
-u32 intel_panel_backlight_level_to_pwm(struct intel_connector *connector, u32 level);
-u32 intel_panel_backlight_level_from_pwm(struct intel_connector *connector, u32 val);
-
-#if IS_ENABLED(CONFIG_BACKLIGHT_CLASS_DEVICE)
-int intel_backlight_device_register(struct intel_connector *connector);
-void intel_backlight_device_unregister(struct intel_connector *connector);
-#else /* CONFIG_BACKLIGHT_CLASS_DEVICE */
-static inline int intel_backlight_device_register(struct intel_connector *connector)
-{
-	return 0;
-}
-static inline void intel_backlight_device_unregister(struct intel_connector *connector)
-{
-}
-#endif /* CONFIG_BACKLIGHT_CLASS_DEVICE */
 
 #endif /* __INTEL_PANEL_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_pps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_pps.c
@@ -1074,14 +1074,14 @@
 	edp_panel_vdd_schedule_off(intel_dp);
 }
 
-bool intel_pps_have_power(struct intel_dp *intel_dp)
+bool intel_pps_have_panel_power_or_vdd(struct intel_dp *intel_dp)
 {
 	intel_wakeref_t wakeref;
 	bool have_power = false;
 
 	with_intel_pps_lock(intel_dp, wakeref) {
-		have_power = edp_have_panel_power(intel_dp) &&
-						  edp_have_panel_vdd(intel_dp);
+		have_power = edp_have_panel_power(intel_dp) ||
+			     edp_have_panel_vdd(intel_dp);
 	}
 
 	return have_power;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_pps.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_pps.h
@@ -36,7 +36,7 @@
 void intel_pps_on(struct intel_dp *intel_dp);
 void intel_pps_off(struct intel_dp *intel_dp);
 void intel_pps_vdd_off_sync(struct intel_dp *intel_dp);
-bool intel_pps_have_power(struct intel_dp *intel_dp);
+bool intel_pps_have_panel_power_or_vdd(struct intel_dp *intel_dp);
 void intel_pps_wait_power_cycle(struct intel_dp *intel_dp);
 
 void intel_pps_init(struct intel_dp *intel_dp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_psr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_psr.c
@@ -22,6 +22,7 @@
  */
 
 #include <drm/drm_atomic_helper.h>
+#include <drm/drm_damage_helper.h>
 
 #include "display/intel_dp.h"
 
@@ -364,41 +365,6 @@
 	}
 }
 
-static void hsw_psr_setup_aux(struct intel_dp *intel_dp)
-{
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-	u32 aux_clock_divider, aux_ctl;
-	int i;
-	static const u8 aux_msg[] = {
-		[0] = DP_AUX_NATIVE_WRITE << 4,
-		[1] = DP_SET_POWER >> 8,
-		[2] = DP_SET_POWER & 0xff,
-		[3] = 1 - 1,
-		[4] = DP_SET_POWER_D0,
-	};
-	u32 psr_aux_mask = EDP_PSR_AUX_CTL_TIME_OUT_MASK |
-			   EDP_PSR_AUX_CTL_MESSAGE_SIZE_MASK |
-			   EDP_PSR_AUX_CTL_PRECHARGE_2US_MASK |
-			   EDP_PSR_AUX_CTL_BIT_CLOCK_2X_MASK;
-
-	BUILD_BUG_ON(sizeof(aux_msg) > 20);
-	for (i = 0; i < sizeof(aux_msg); i += 4)
-		intel_de_write(dev_priv,
-			       EDP_PSR_AUX_DATA(intel_dp->psr.transcoder, i >> 2),
-			       intel_dp_pack_aux(&aux_msg[i], sizeof(aux_msg) - i));
-
-	aux_clock_divider = intel_dp->get_aux_clock_divider(intel_dp, 0);
-
-	/* Start with bits set for DDI_AUX_CTL register */
-	aux_ctl = intel_dp->get_aux_send_ctl(intel_dp, sizeof(aux_msg),
-					     aux_clock_divider);
-
-	/* Select only valid bits for SRD_AUX_CTL */
-	aux_ctl &= psr_aux_mask;
-	intel_de_write(dev_priv, EDP_PSR_AUX_CTL(intel_dp->psr.transcoder),
-		       aux_ctl);
-}
-
 static void intel_psr_enable_sink(struct intel_dp *intel_dp)
 {
 	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
@@ -548,6 +514,14 @@
 	val |= EDP_PSR2_FRAME_BEFORE_SU(intel_dp->psr.sink_sync_latency + 1);
 	val |= intel_psr2_get_tp_time(intel_dp);
 
+	if (DISPLAY_VER(dev_priv) >= 12) {
+		if (intel_dp->psr.io_wake_lines < 9 &&
+		    intel_dp->psr.fast_wake_lines < 9)
+			val |= TGL_EDP_PSR2_BLOCK_COUNT_NUM_2;
+		else
+			val |= TGL_EDP_PSR2_BLOCK_COUNT_NUM_3;
+	}
+
 	/* Wa_22012278275:adl-p */
 	if (IS_ADLP_DISPLAY_STEP(dev_priv, STEP_A0, STEP_E0)) {
 		static const u8 map[] = {
@@ -564,31 +538,21 @@
 		 * Still using the default IO_BUFFER_WAKE and FAST_WAKE, see
 		 * comments bellow for more information
 		 */
-		u32 tmp, lines = 7;
-
-		val |= TGL_EDP_PSR2_BLOCK_COUNT_NUM_2;
+		u32 tmp;
 
-		tmp = map[lines - TGL_EDP_PSR2_IO_BUFFER_WAKE_MIN_LINES];
+		tmp = map[intel_dp->psr.io_wake_lines - TGL_EDP_PSR2_IO_BUFFER_WAKE_MIN_LINES];
 		tmp = tmp << TGL_EDP_PSR2_IO_BUFFER_WAKE_SHIFT;
 		val |= tmp;
 
-		tmp = map[lines - TGL_EDP_PSR2_FAST_WAKE_MIN_LINES];
+		tmp = map[intel_dp->psr.fast_wake_lines - TGL_EDP_PSR2_FAST_WAKE_MIN_LINES];
 		tmp = tmp << TGL_EDP_PSR2_FAST_WAKE_MIN_SHIFT;
 		val |= tmp;
 	} else if (DISPLAY_VER(dev_priv) >= 12) {
-		/*
-		 * TODO: 7 lines of IO_BUFFER_WAKE and FAST_WAKE are default
-		 * values from BSpec. In order to setting an optimal power
-		 * consumption, lower than 4k resoluition mode needs to decrese
-		 * IO_BUFFER_WAKE and FAST_WAKE. And higher than 4K resolution
-		 * mode needs to increase IO_BUFFER_WAKE and FAST_WAKE.
-		 */
-		val |= TGL_EDP_PSR2_BLOCK_COUNT_NUM_2;
-		val |= TGL_EDP_PSR2_IO_BUFFER_WAKE(7);
-		val |= TGL_EDP_PSR2_FAST_WAKE(7);
+		val |= TGL_EDP_PSR2_IO_BUFFER_WAKE(intel_dp->psr.io_wake_lines);
+		val |= TGL_EDP_PSR2_FAST_WAKE(intel_dp->psr.fast_wake_lines);
 	} else if (DISPLAY_VER(dev_priv) >= 9) {
-		val |= EDP_PSR2_IO_BUFFER_WAKE(7);
-		val |= EDP_PSR2_FAST_WAKE(7);
+		val |= EDP_PSR2_IO_BUFFER_WAKE(intel_dp->psr.io_wake_lines);
+		val |= EDP_PSR2_FAST_WAKE(intel_dp->psr.fast_wake_lines);
 	}
 
 	if (intel_dp->psr.req_psr2_sdp_prior_scanline)
@@ -621,9 +585,7 @@
 static bool
 transcoder_has_psr2(struct drm_i915_private *dev_priv, enum transcoder trans)
 {
-	if (DISPLAY_VER(dev_priv) < 9)
-		return false;
-	else if (DISPLAY_VER(dev_priv) >= 12)
+	if (DISPLAY_VER(dev_priv) >= 12)
 		return trans == TRANSCODER_A;
 	else
 		return trans == TRANSCODER_EDP;
@@ -755,11 +717,18 @@
 static bool intel_psr2_sel_fetch_config_valid(struct intel_dp *intel_dp,
 					      struct intel_crtc_state *crtc_state)
 {
-	struct intel_atomic_state *state = to_intel_atomic_state(crtc_state->uapi.state);
 	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
-	struct intel_plane_state *plane_state;
-	struct intel_plane *plane;
-	int i;
+	struct edid *edid;
+
+	edid = intel_dp_get_edid(intel_dp);
+
+	if (edid->mfg_id[0] == 0x06 && edid->mfg_id[1] == 0xaf &&
+	    edid->prod_code[0] == 0x8c && edid->prod_code[1] == 0xcd &&
+	    IS_TIGERLAKE(dev_priv)) {
+		drm_info_once(&dev_priv->drm,
+			      "PSR2 sel fetch enabled for TGL + AUO panel\n");
+		return crtc_state->enable_psr2_sel_fetch = true;
+	}
 
 	if (!dev_priv->params.enable_psr2_sel_fetch &&
 	    intel_dp->psr.debug != I915_PSR_DEBUG_ENABLE_SEL_FETCH) {
@@ -774,14 +743,6 @@
 		return false;
 	}
 
-	for_each_new_intel_plane_in_state(state, plane, plane_state, i) {
-		if (plane_state->uapi.rotation != DRM_MODE_ROTATE_0) {
-			drm_dbg_kms(&dev_priv->drm,
-				    "PSR2 sel fetch not enabled, plane rotated\n");
-			return false;
-		}
-	}
-
 	/* Wa_14010254185 Wa_14010103792 */
 	if (IS_TGL_DISPLAY_STEP(dev_priv, STEP_A0, STEP_C0)) {
 		drm_dbg_kms(&dev_priv->drm,
@@ -853,6 +814,46 @@
 	return true;
 }
 
+static bool _compute_psr2_wake_times(struct intel_dp *intel_dp,
+				     struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+	int io_wake_lines, io_wake_time, fast_wake_lines, fast_wake_time;
+	u8 max_wake_lines;
+
+	if (DISPLAY_VER(i915) >= 12) {
+		io_wake_time = 42;
+		/*
+		 * According to Bspec it's 42us, but based on testing
+		 * it is not enough -> use 45 us.
+		 */
+		fast_wake_time = 45;
+		max_wake_lines = 12;
+	} else {
+		io_wake_time = 50;
+		fast_wake_time = 32;
+		max_wake_lines = 8;
+	}
+
+	io_wake_lines = intel_usecs_to_scanlines(
+		&crtc_state->hw.adjusted_mode, io_wake_time);
+	fast_wake_lines = intel_usecs_to_scanlines(
+		&crtc_state->hw.adjusted_mode, fast_wake_time);
+
+	if (io_wake_lines > max_wake_lines ||
+	    fast_wake_lines > max_wake_lines)
+		return false;
+
+	if (i915->params.psr_safest_params)
+		io_wake_lines = fast_wake_lines = max_wake_lines;
+
+	/* According to Bspec lower limit should be set as 7 lines. */
+	intel_dp->psr.io_wake_lines = max(io_wake_lines, 7);
+	intel_dp->psr.fast_wake_lines = max(fast_wake_lines, 7);
+
+	return true;
+}
+
 static bool intel_psr2_config_valid(struct intel_dp *intel_dp,
 				    struct intel_crtc_state *crtc_state)
 {
@@ -936,6 +937,26 @@
 		return false;
 	}
 
+	/* Wa_16011303918:adl-p */
+	if (crtc_state->vrr.enable &&
+	    IS_ADLP_DISPLAY_STEP(dev_priv, STEP_A0, STEP_B0)) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "PSR2 not enabled, not compatible with HW stepping + VRR\n");
+		return false;
+	}
+
+	if (!_compute_psr2_sdp_prior_scanline_indication(intel_dp, crtc_state)) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "PSR2 not enabled, PSR2 SDP indication do not fit in hblank\n");
+		return false;
+	}
+
+	if (!_compute_psr2_wake_times(intel_dp, crtc_state)) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "PSR2 not enabled, Unable to use long enough wake times\n");
+		return false;
+	}
+
 	if (HAS_PSR2_SEL_FETCH(dev_priv)) {
 		if (!intel_psr2_sel_fetch_config_valid(intel_dp, crtc_state) &&
 		    !HAS_PSR_HW_TRACKING(dev_priv)) {
@@ -949,12 +970,12 @@
 	if (!crtc_state->enable_psr2_sel_fetch &&
 	    IS_TGL_DISPLAY_STEP(dev_priv, STEP_A0, STEP_C0)) {
 		drm_dbg_kms(&dev_priv->drm, "PSR2 HW tracking is not supported this Display stepping\n");
-		return false;
+		goto unsupported;
 	}
 
 	if (!psr2_granularity_check(intel_dp, crtc_state)) {
 		drm_dbg_kms(&dev_priv->drm, "PSR2 not enabled, SU granularity not compatible\n");
-		return false;
+		goto unsupported;
 	}
 
 	if (!crtc_state->enable_psr2_sel_fetch &&
@@ -963,25 +984,15 @@
 			    "PSR2 not enabled, resolution %dx%d > max supported %dx%d\n",
 			    crtc_hdisplay, crtc_vdisplay,
 			    psr_max_h, psr_max_v);
-		return false;
-	}
-
-	if (!_compute_psr2_sdp_prior_scanline_indication(intel_dp, crtc_state)) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "PSR2 not enabled, PSR2 SDP indication do not fit in hblank\n");
-		return false;
-	}
-
-	/* Wa_16011303918:adl-p */
-	if (crtc_state->vrr.enable &&
-	    IS_ADLP_DISPLAY_STEP(dev_priv, STEP_A0, STEP_B0)) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "PSR2 not enabled, not compatible with HW stepping + VRR\n");
-		return false;
+		goto unsupported;
 	}
 
 	tgl_dc3co_exitline_compute_config(intel_dp, crtc_state);
 	return true;
+
+unsupported:
+	crtc_state->enable_psr2_sel_fetch = false;
+	return false;
 }
 
 void intel_psr_compute_config(struct intel_dp *intel_dp,
@@ -993,7 +1004,7 @@
 	int psr_setup_time;
 
 	/*
-	 * Current PSR panels dont work reliably with VRR enabled
+	 * Current PSR panels don't work reliably with VRR enabled
 	 * So if VRR is enabled, do not enable PSR.
 	 */
 	if (crtc_state->vrr.enable)
@@ -1114,12 +1125,6 @@
 	enum transcoder cpu_transcoder = intel_dp->psr.transcoder;
 	u32 mask;
 
-	/* Only HSW and BDW have PSR AUX registers that need to be setup. SKL+
-	 * use hardcoded values PSR AUX transactions
-	 */
-	if (IS_HASWELL(dev_priv) || IS_BROADWELL(dev_priv))
-		hsw_psr_setup_aux(intel_dp);
-
 	if (intel_dp->psr.psr2_enabled && DISPLAY_VER(dev_priv) == 9) {
 		i915_reg_t reg = CHICKEN_TRANS(cpu_transcoder);
 		u32 chicken = intel_de_read(dev_priv, reg);
@@ -1456,27 +1461,36 @@
 	mutex_unlock(&psr->lock);
 }
 
+static inline u32 man_trk_ctl_single_full_frame_bit_get(struct drm_i915_private *dev_priv)
+{
+	return IS_ALDERLAKE_P(dev_priv) ?
+	       ADLP_PSR2_MAN_TRK_CTL_SF_SINGLE_FULL_FRAME :
+	       PSR2_MAN_TRK_CTL_SF_SINGLE_FULL_FRAME;
+}
+
 static void psr_force_hw_tracking_exit(struct intel_dp *intel_dp)
 {
 	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
 
-	if (DISPLAY_VER(dev_priv) >= 9)
-		/*
-		 * Display WA #0884: skl+
-		 * This documented WA for bxt can be safely applied
-		 * broadly so we can force HW tracking to exit PSR
-		 * instead of disabling and re-enabling.
-		 * Workaround tells us to write 0 to CUR_SURFLIVE_A,
-		 * but it makes more sense write to the current active
-		 * pipe.
-		 */
-		intel_de_write(dev_priv, CURSURFLIVE(intel_dp->psr.pipe), 0);
-	else
-		/*
-		 * A write to CURSURFLIVE do not cause HW tracking to exit PSR
-		 * on older gens so doing the manual exit instead.
-		 */
-		intel_psr_exit(intel_dp);
+	if (intel_dp->psr.psr2_sel_fetch_enabled)
+		intel_de_rmw(dev_priv,
+			     PSR2_MAN_TRK_CTL(intel_dp->psr.transcoder), 0,
+			     man_trk_ctl_single_full_frame_bit_get(dev_priv));
+
+	/*
+	 * Display WA #0884: skl+
+	 * This documented WA for bxt can be safely applied
+	 * broadly so we can force HW tracking to exit PSR
+	 * instead of disabling and re-enabling.
+	 * Workaround tells us to write 0 to CUR_SURFLIVE_A,
+	 * but it makes more sense write to the current active
+	 * pipe.
+	 *
+	 * This workaround do not exist for platforms with display 10 or newer
+	 * but testing proved that it works for up display 13, for newer
+	 * than that testing will be needed.
+	 */
+	intel_de_write(dev_priv, CURSURFLIVE(intel_dp->psr.pipe), 0);
 }
 
 void intel_psr2_program_plane_sel_fetch(struct intel_plane *plane,
@@ -1487,8 +1501,8 @@
 	struct drm_i915_private *dev_priv = to_i915(plane->base.dev);
 	enum pipe pipe = plane->pipe;
 	const struct drm_rect *clip;
-	u32 val, offset;
-	int ret, x, y;
+	u32 val;
+	int x, y;
 
 	if (!crtc_state->enable_psr2_sel_fetch)
 		return;
@@ -1508,10 +1522,6 @@
 	/* TODO: consider auxiliary surfaces */
 	x = plane_state->uapi.src.x1 >> 16;
 	y = (plane_state->uapi.src.y1 >> 16) + clip->y1;
-	ret = skl_calc_main_surface_offset(plane_state, &x, &y, &offset);
-	if (ret)
-		drm_warn_once(&dev_priv->drm, "skl_calc_main_surface_offset() returned %i\n",
-			      ret);
 	val = y << 16 | x;
 	intel_de_write_fw(dev_priv, PLANE_SEL_FETCH_OFFSET(pipe, plane->id),
 			  val);
@@ -1597,6 +1607,67 @@
 		drm_warn(&dev_priv->drm, "Missing PSR2 sel fetch alignment with DSC\n");
 }
 
+/*
+ * TODO: Not clear how to handle planes with negative position,
+ * also planes are not updated if they have a negative X
+ * position so for now doing a full update in this cases
+ *
+ * TODO: We are missing multi-planar formats handling, until it is
+ * implemented it will send full frame updates.
+ *
+ * Plane scaling and rotation is not supported by selective fetch and both
+ * properties can change without a modeset, so need to be check at every
+ * atomic commit.
+ */
+static bool psr2_sel_fetch_plane_state_supported(const struct intel_plane_state *plane_state)
+{
+	if (plane_state->uapi.dst.y1 < 0 ||
+	    plane_state->uapi.dst.x1 < 0 ||
+	    plane_state->scaler_id >= 0 ||
+	    plane_state->hw.fb->format->num_planes > 1 ||
+	    plane_state->uapi.rotation != DRM_MODE_ROTATE_0)
+		return false;
+
+	return true;
+}
+
+/*
+ * Check for pipe properties that is not supported by selective fetch.
+ *
+ * TODO: pipe scaling causes a modeset but skl_update_scaler_crtc() is executed
+ * after intel_psr_compute_config(), so for now keeping PSR2 selective fetch
+ * enabled and going to the full update path.
+ */
+static bool psr2_sel_fetch_pipe_state_supported(const struct intel_crtc_state *crtc_state)
+{
+	if (crtc_state->scaler_state.scaler_id >= 0)
+		return false;
+
+	return true;
+}
+
+/*
+ * FIXME: Not sure why but when moving the cursor fast it causes some artifacts
+ * of the cursor to be left in the cursor path, adding some pixels above the
+ * cursor to the damaged area fixes the issue.
+ */
+static void cursor_area_workaround(const struct intel_plane_state *new_plane_state,
+				   struct drm_rect *damaged_area,
+				   struct drm_rect *pipe_clip)
+{
+	const struct intel_plane *plane = to_intel_plane(new_plane_state->uapi.plane);
+	int height;
+
+	if (plane->id != PLANE_CURSOR)
+		return;
+
+	height = drm_rect_height(&new_plane_state->uapi.dst) / 2;
+	damaged_area->y1 -=  height;
+	damaged_area->y1 = max(damaged_area->y1, 0);
+
+	clip_area_update(pipe_clip, damaged_area);
+}
+
 int intel_psr2_sel_fetch_update(struct intel_atomic_state *state,
 				struct intel_crtc *crtc)
 {
@@ -1610,9 +1681,10 @@
 	if (!crtc_state->enable_psr2_sel_fetch)
 		return 0;
 
-	ret = drm_atomic_add_affected_planes(&state->base, &crtc->base);
-	if (ret)
-		return ret;
+	if (!psr2_sel_fetch_pipe_state_supported(crtc_state)) {
+		full_update = true;
+		goto skip_sel_fetch_set_loop;
+	}
 
 	/*
 	 * Calculate minimal selective fetch area of each plane and calculate
@@ -1623,8 +1695,8 @@
 	for_each_oldnew_intel_plane_in_state(state, plane, old_plane_state,
 					     new_plane_state, i) {
 		struct drm_rect src, damaged_area = { .y1 = -1 };
-		struct drm_mode_rect *damaged_clips;
-		u32 num_clips, j;
+		struct drm_atomic_helper_damage_iter iter;
+		struct drm_rect clip;
 
 		if (new_plane_state->uapi.crtc != crtc_state->uapi.crtc)
 			continue;
@@ -1633,19 +1705,11 @@
 		    !old_plane_state->uapi.visible)
 			continue;
 
-		/*
-		 * TODO: Not clear how to handle planes with negative position,
-		 * also planes are not updated if they have a negative X
-		 * position so for now doing a full update in this cases
-		 */
-		if (new_plane_state->uapi.dst.y1 < 0 ||
-		    new_plane_state->uapi.dst.x1 < 0) {
+		if (!psr2_sel_fetch_plane_state_supported(new_plane_state)) {
 			full_update = true;
 			break;
 		}
 
-		num_clips = drm_plane_get_damage_clips_count(&new_plane_state->uapi);
-
 		/*
 		 * If visibility or plane moved, mark the whole plane area as
 		 * damaged as it needs to be complete redraw in the new and old
@@ -1665,15 +1729,12 @@
 				damaged_area.y2 = new_plane_state->uapi.dst.y2;
 				clip_area_update(&pipe_clip, &damaged_area);
 			}
+
+			cursor_area_workaround(new_plane_state, &damaged_area,
+					       &pipe_clip);
 			continue;
-		} else if (new_plane_state->uapi.alpha != old_plane_state->uapi.alpha ||
-			   (!num_clips &&
-			    new_plane_state->uapi.fb != old_plane_state->uapi.fb)) {
-			/*
-			 * If the plane don't have damaged areas but the
-			 * framebuffer changed or alpha changed, mark the whole
-			 * plane area as damaged.
-			 */
+		} else if (new_plane_state->uapi.alpha != old_plane_state->uapi.alpha) {
+			/* If alpha changed mark the whole plane area as damaged */
 			damaged_area.y1 = new_plane_state->uapi.dst.y1;
 			damaged_area.y2 = new_plane_state->uapi.dst.y2;
 			clip_area_update(&pipe_clip, &damaged_area);
@@ -1681,15 +1742,11 @@
 		}
 
 		drm_rect_fp_to_int(&src, &new_plane_state->uapi.src);
-		damaged_clips = drm_plane_get_damage_clips(&new_plane_state->uapi);
-
-		for (j = 0; j < num_clips; j++) {
-			struct drm_rect clip;
 
-			clip.x1 = damaged_clips[j].x1;
-			clip.y1 = damaged_clips[j].y1;
-			clip.x2 = damaged_clips[j].x2;
-			clip.y2 = damaged_clips[j].y2;
+		drm_atomic_helper_damage_iter_init(&iter,
+						   &old_plane_state->uapi,
+						   &new_plane_state->uapi);
+		drm_atomic_for_each_plane_damage(&iter, &clip) {
 			if (drm_rect_intersect(&clip, &src))
 				clip_area_update(&damaged_area, &clip);
 		}
@@ -1705,6 +1762,10 @@
 	if (full_update)
 		goto skip_sel_fetch_set_loop;
 
+	ret = drm_atomic_add_affected_planes(&state->base, &crtc->base);
+	if (ret)
+		return ret;
+
 	intel_psr2_sel_fetch_pipe_alignment(crtc_state, &pipe_clip);
 
 	/*
@@ -1723,6 +1784,11 @@
 		if (!drm_rect_intersect(&inter, &new_plane_state->uapi.dst))
 			continue;
 
+		if (!psr2_sel_fetch_plane_state_supported(new_plane_state)) {
+			full_update = true;
+			break;
+		}
+
 		sel_fetch_area = &new_plane_state->psr2_sel_fetch_area;
 		sel_fetch_area->y1 = inter.y1 - new_plane_state->uapi.dst.y1;
 		sel_fetch_area->y2 = inter.y2 - new_plane_state->uapi.dst.y1;
@@ -1748,7 +1814,6 @@
 		      const struct intel_crtc_state *crtc_state,
 		      const struct drm_connector_state *conn_state)
 {
-	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
 	struct intel_psr *psr = &intel_dp->psr;
 	bool enable, psr2_enable;
 
@@ -1765,15 +1830,6 @@
 		/* Force a PSR exit when enabling CRC to avoid CRC timeouts */
 		if (crtc_state->crc_enabled && psr->enabled)
 			psr_force_hw_tracking_exit(intel_dp);
-		else if (DISPLAY_VER(dev_priv) < 9 && psr->enabled) {
-			/*
-			 * Activate PSR again after a force exit when enabling
-			 * CRC in older gens
-			 */
-			if (!intel_dp->psr.active &&
-			    !intel_dp->psr.busy_frontbuffer_bits)
-				schedule_work(&intel_dp->psr.work);
-		}
 
 		goto unlock;
 	}
@@ -2022,7 +2078,7 @@
 }
 
 /**
- * intel_psr_invalidate - Invalidade PSR
+ * intel_psr_invalidate - Invalidate PSR
  * @dev_priv: i915 device
  * @frontbuffer_bits: frontbuffer plane tracking bits
  * @origin: which operation caused the invalidate
@@ -2065,20 +2121,16 @@
 /*
  * When we will be completely rely on PSR2 S/W tracking in future,
  * intel_psr_flush() will invalidate and flush the PSR for ORIGIN_FLIP
- * event also therefore tgl_dc3co_flush() require to be changed
+ * event also therefore tgl_dc3co_flush_locked() require to be changed
  * accordingly in future.
  */
 static void
-tgl_dc3co_flush(struct intel_dp *intel_dp, unsigned int frontbuffer_bits,
-		enum fb_op_origin origin)
+tgl_dc3co_flush_locked(struct intel_dp *intel_dp, unsigned int frontbuffer_bits,
+		       enum fb_op_origin origin)
 {
-	mutex_lock(&intel_dp->psr.lock);
-
-	if (!intel_dp->psr.dc3co_exitline)
-		goto unlock;
-
-	if (!intel_dp->psr.psr2_enabled || !intel_dp->psr.active)
-		goto unlock;
+	if (!intel_dp->psr.dc3co_exitline || !intel_dp->psr.psr2_enabled ||
+	    !intel_dp->psr.active)
+		return;
 
 	/*
 	 * At every frontbuffer flush flip event modified delay of delayed work,
@@ -2086,14 +2138,11 @@
 	 */
 	if (!(frontbuffer_bits &
 	    INTEL_FRONTBUFFER_ALL_MASK(intel_dp->psr.pipe)))
-		goto unlock;
+		return;
 
 	tgl_psr2_enable_dc3co(intel_dp);
 	mod_delayed_work(system_wq, &intel_dp->psr.dc3co_work,
 			 intel_dp->psr.dc3co_exit_delay);
-
-unlock:
-	mutex_unlock(&intel_dp->psr.lock);
 }
 
 /**
@@ -2118,11 +2167,6 @@
 		unsigned int pipe_frontbuffer_bits = frontbuffer_bits;
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
-		if (origin == ORIGIN_FLIP) {
-			tgl_dc3co_flush(intel_dp, frontbuffer_bits, origin);
-			continue;
-		}
-
 		mutex_lock(&intel_dp->psr.lock);
 		if (!intel_dp->psr.enabled) {
 			mutex_unlock(&intel_dp->psr.lock);
@@ -2143,6 +2187,14 @@
 			continue;
 		}
 
+		if (origin == ORIGIN_FLIP ||
+		    (origin == ORIGIN_CURSOR_UPDATE &&
+		     !intel_dp->psr.psr2_sel_fetch_enabled)) {
+			tgl_dc3co_flush_locked(intel_dp, frontbuffer_bits, origin);
+			mutex_unlock(&intel_dp->psr.lock);
+			continue;
+		}
+
 		/* By definition flush = invalidate + flush */
 		if (pipe_frontbuffer_bits)
 			psr_force_hw_tracking_exit(intel_dp);
@@ -2186,23 +2238,12 @@
 
 	intel_dp->psr.source_support = true;
 
-	if (IS_HASWELL(dev_priv))
-		/*
-		 * HSW don't have PSR registers on the same space as transcoder
-		 * so set this to a value that when subtract to the register
-		 * in transcoder space results in the right offset for HSW
-		 */
-		dev_priv->hsw_psr_mmio_adjust = _SRD_CTL_EDP - _HSW_EDP_PSR_BASE;
-
 	if (dev_priv->params.enable_psr == -1)
-		if (DISPLAY_VER(dev_priv) < 9 || !dev_priv->vbt.psr.enable)
+		if (!dev_priv->vbt.psr.enable)
 			dev_priv->params.enable_psr = 0;
 
 	/* Set link_standby x link_off defaults */
-	if (IS_HASWELL(dev_priv) || IS_BROADWELL(dev_priv))
-		/* HSW and BDW require workarounds that we don't implement. */
-		intel_dp->psr.link_standby = false;
-	else if (DISPLAY_VER(dev_priv) < 12)
+	if (DISPLAY_VER(dev_priv) < 12)
 		/* For new platforms up to TGL let's respect VBT back again */
 		intel_dp->psr.link_standby = dev_priv->vbt.psr.full_link;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_quirks.c
@@ -59,6 +59,12 @@
 	drm_info(&i915->drm, "Applying no pps backlight power quirk\n");
 }
 
+static void quirk_force_disable_fastboot_hook(struct drm_i915_private *i915)
+{
+	i915->quirks |= QUIRK_FORCE_DISABLE_FASTBOOT;
+	drm_info(&i915->drm, "Applying force disable fastboot quirk\n");
+}
+
 struct intel_quirk {
 	int device;
 	int subsystem_vendor;
@@ -84,6 +90,12 @@
 	return 1;
 }
 
+static int intel_dmi_force_disable_fastboot(const struct dmi_system_id *id)
+{
+	DRM_INFO("Force disable fastboot on %s\n", id->ident);
+	return 1;
+}
+
 static const struct intel_dmi_quirk intel_dmi_quirks[] = {
 	{
 		.dmi_id_list = &(const struct dmi_system_id[]) {
@@ -130,6 +142,19 @@
 		},
 		.hook = quirk_no_pps_backlight_power_hook,
 	},
+	{
+		.dmi_id_list = &(const struct dmi_system_id[]) {
+			{
+				.callback = intel_dmi_force_disable_fastboot,
+				.ident = "B&R Industrial Automation APC2200",
+				.matches = {DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "B&R Industrial Automation"),
+					    DMI_EXACT_MATCH(DMI_BOARD_NAME, "APC2200"),
+				},
+			},
+			{ }
+		},
+		.hook = quirk_force_disable_fastboot_hook,
+	},
 };
 
 static struct intel_quirk intel_quirks[] = {
@@ -190,6 +215,11 @@
 	/* ASRock ITX*/
 	{ 0x3185, 0x1849, 0x2212, quirk_increase_ddi_disabled_time },
 	{ 0x3184, 0x1849, 0x2212, quirk_increase_ddi_disabled_time },
+	/* ECS Liva Q2 */
+	{ 0x3185, 0x1019, 0xa94d, quirk_increase_ddi_disabled_time },
+	{ 0x3184, 0x1019, 0xa94d, quirk_increase_ddi_disabled_time },
+	/* HP Notebook - 14-r206nv */
+	{ 0x0f31, 0x103c, 0x220f, quirk_invert_brightness },
 };
 
 void intel_init_quirks(struct drm_i915_private *i915)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_sdvo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_sdvo.c
@@ -1863,13 +1863,19 @@
 intel_sdvo_mode_valid(struct drm_connector *connector,
 		      struct drm_display_mode *mode)
 {
+	struct drm_i915_private *i915 = to_i915(connector->dev);
 	struct intel_sdvo *intel_sdvo = intel_attached_sdvo(to_intel_connector(connector));
 	struct intel_sdvo_connector *intel_sdvo_connector =
 		to_intel_sdvo_connector(connector);
-	int max_dotclk = to_i915(connector->dev)->max_dotclk_freq;
+	int max_dotclk = i915->max_dotclk_freq;
 	bool has_hdmi_sink = intel_has_hdmi_sink(intel_sdvo, connector->state);
+	enum drm_mode_status status;
 	int clock = mode->clock;
 
+	status = intel_cpu_transcoder_mode_valid(i915, mode);
+	if (status != MODE_OK)
+		return status;
+
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return MODE_NO_DBLESCAN;
 
@@ -2762,13 +2768,10 @@
 	if (!intel_sdvo_connector)
 		return false;
 
-	if (device == 0) {
-		intel_sdvo->controlled_output |= SDVO_OUTPUT_TMDS0;
+	if (device == 0)
 		intel_sdvo_connector->output_flag = SDVO_OUTPUT_TMDS0;
-	} else if (device == 1) {
-		intel_sdvo->controlled_output |= SDVO_OUTPUT_TMDS1;
+	else if (device == 1)
 		intel_sdvo_connector->output_flag = SDVO_OUTPUT_TMDS1;
-	}
 
 	intel_connector = &intel_sdvo_connector->base;
 	connector = &intel_connector->base;
@@ -2823,7 +2826,6 @@
 	encoder->encoder_type = DRM_MODE_ENCODER_TVDAC;
 	connector->connector_type = DRM_MODE_CONNECTOR_SVIDEO;
 
-	intel_sdvo->controlled_output |= type;
 	intel_sdvo_connector->output_flag = type;
 
 	if (intel_sdvo_connector_init(intel_sdvo_connector, intel_sdvo) < 0) {
@@ -2864,13 +2866,10 @@
 	encoder->encoder_type = DRM_MODE_ENCODER_DAC;
 	connector->connector_type = DRM_MODE_CONNECTOR_VGA;
 
-	if (device == 0) {
-		intel_sdvo->controlled_output |= SDVO_OUTPUT_RGB0;
+	if (device == 0)
 		intel_sdvo_connector->output_flag = SDVO_OUTPUT_RGB0;
-	} else if (device == 1) {
-		intel_sdvo->controlled_output |= SDVO_OUTPUT_RGB1;
+	else if (device == 1)
 		intel_sdvo_connector->output_flag = SDVO_OUTPUT_RGB1;
-	}
 
 	if (intel_sdvo_connector_init(intel_sdvo_connector, intel_sdvo) < 0) {
 		kfree(intel_sdvo_connector);
@@ -2900,13 +2899,10 @@
 	encoder->encoder_type = DRM_MODE_ENCODER_LVDS;
 	connector->connector_type = DRM_MODE_CONNECTOR_LVDS;
 
-	if (device == 0) {
-		intel_sdvo->controlled_output |= SDVO_OUTPUT_LVDS0;
+	if (device == 0)
 		intel_sdvo_connector->output_flag = SDVO_OUTPUT_LVDS0;
-	} else if (device == 1) {
-		intel_sdvo->controlled_output |= SDVO_OUTPUT_LVDS1;
+	else if (device == 1)
 		intel_sdvo_connector->output_flag = SDVO_OUTPUT_LVDS1;
-	}
 
 	if (intel_sdvo_connector_init(intel_sdvo_connector, intel_sdvo) < 0) {
 		kfree(intel_sdvo_connector);
@@ -2939,16 +2935,39 @@
 	return false;
 }
 
+static u16 intel_sdvo_filter_output_flags(u16 flags)
+{
+	flags &= SDVO_OUTPUT_MASK;
+
+	/* SDVO requires XXX1 function may not exist unless it has XXX0 function.*/
+	if (!(flags & SDVO_OUTPUT_TMDS0))
+		flags &= ~SDVO_OUTPUT_TMDS1;
+
+	if (!(flags & SDVO_OUTPUT_RGB0))
+		flags &= ~SDVO_OUTPUT_RGB1;
+
+	if (!(flags & SDVO_OUTPUT_LVDS0))
+		flags &= ~SDVO_OUTPUT_LVDS1;
+
+	return flags;
+}
+
 static bool
 intel_sdvo_output_setup(struct intel_sdvo *intel_sdvo, u16 flags)
 {
-	/* SDVO requires XXX1 function may not exist unless it has XXX0 function.*/
+	struct drm_i915_private *i915 = to_i915(intel_sdvo->base.base.dev);
+
+	flags = intel_sdvo_filter_output_flags(flags);
+
+	intel_sdvo->controlled_output = flags;
+
+	intel_sdvo_select_ddc_bus(i915, intel_sdvo);
 
 	if (flags & SDVO_OUTPUT_TMDS0)
 		if (!intel_sdvo_dvi_init(intel_sdvo, 0))
 			return false;
 
-	if ((flags & SDVO_TMDS_MASK) == SDVO_TMDS_MASK)
+	if (flags & SDVO_OUTPUT_TMDS1)
 		if (!intel_sdvo_dvi_init(intel_sdvo, 1))
 			return false;
 
@@ -2969,7 +2988,7 @@
 		if (!intel_sdvo_analog_init(intel_sdvo, 0))
 			return false;
 
-	if ((flags & SDVO_RGB_MASK) == SDVO_RGB_MASK)
+	if (flags & SDVO_OUTPUT_RGB1)
 		if (!intel_sdvo_analog_init(intel_sdvo, 1))
 			return false;
 
@@ -2977,14 +2996,13 @@
 		if (!intel_sdvo_lvds_init(intel_sdvo, 0))
 			return false;
 
-	if ((flags & SDVO_LVDS_MASK) == SDVO_LVDS_MASK)
+	if (flags & SDVO_OUTPUT_LVDS1)
 		if (!intel_sdvo_lvds_init(intel_sdvo, 1))
 			return false;
 
-	if ((flags & SDVO_OUTPUT_MASK) == 0) {
+	if (flags == 0) {
 		unsigned char bytes[2];
 
-		intel_sdvo->controlled_output = 0;
 		memcpy(bytes, &intel_sdvo->caps.output_flags, 2);
 		DRM_DEBUG_KMS("%s: Unknown SDVO output type (0x%02x%02x)\n",
 			      SDVO_NAME(intel_sdvo),
@@ -3396,8 +3414,6 @@
 	 */
 	intel_sdvo->base.cloneable = 0;
 
-	intel_sdvo_select_ddc_bus(dev_priv, intel_sdvo);
-
 	/* Set the input timing to the screen. Assume always input 0. */
 	if (!intel_sdvo_set_target_input(intel_sdvo))
 		goto err_output;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_snps_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_snps_phy.c
@@ -32,7 +32,7 @@
 		if (intel_de_wait_for_clear(dev_priv, ICL_PHY_MISC(phy),
 					    DG2_PHY_DP_TX_ACK_MASK, 25))
 			DRM_ERROR("SNPS PHY %c failed to calibrate after 25ms.\n",
-				  phy);
+				  phy_name(phy));
 	}
 }
 
@@ -582,6 +582,1177 @@
 		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
 };
 
+/* values in the below table are calculted using the algo */
+static const struct intel_mpllb_state dg2_hdmi_25200 = {
+	.clock = 25200,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 5) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 128) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 41943) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 2621),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_27027 = {
+	.clock = 27027,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 5) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 140) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 31876) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 46555),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_28320 = {
+	.clock = 28320,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 5) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 148) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 40894) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 30408),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_30240 = {
+	.clock = 30240,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 5) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 160) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 50331) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 42466),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_31500 = {
+	.clock = 31500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 68) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 26214) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 26214),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_36000 = {
+	.clock = 36000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 82) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 39321) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 39320),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_40000 = {
+	.clock = 40000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 2),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 96) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_49500 = {
+	.clock = 49500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 1),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 126) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 13107) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 13107),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_50000 = {
+	.clock = 50000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 1),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 128) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_57284 = {
+	.clock = 57284,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 150) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 42886) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 49701),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_58000 = {
+	.clock = 58000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 4) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 152) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 52428) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 52427),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_65000 = {
+	.clock = 65000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 72) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_71000 = {
+	.clock = 71000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 80) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 52428) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 52427),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_74176 = {
+	.clock = 74176,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 86) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 22334) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 43829),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_75000 = {
+	.clock = 75000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 88) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_78750 = {
+	.clock = 78750,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 2),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 94) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_85500 = {
+	.clock = 85500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 2),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 104) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 26214) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 26214),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_88750 = {
+	.clock = 88750,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 15) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 1),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 110) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_106500 = {
+	.clock = 106500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 138) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 13107) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 13107),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_108000 = {
+	.clock = 108000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 140) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 26214) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 26214),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_115500 = {
+	.clock = 115500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 152) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 26214) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 26214),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_119000 = {
+	.clock = 119000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 3) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 158) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 13107) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 13107),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_135000 = {
+	.clock = 135000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 15) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 76) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 0),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_138500 = {
+	.clock = 138500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 78) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 26214) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 26214),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_147160 = {
+	.clock = 147160,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 84) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 56623) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 6815),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_148352 = {
+	.clock = 148352,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 86) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 22334) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 43829),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_154000 = {
+	.clock = 154000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 13) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 2),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 90) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 39321) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 39320),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_162000 = {
+	.clock = 162000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 2),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 96) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 52428) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 52427),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_209800 = {
+	.clock = 209800,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 134) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 60293) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 7864),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_262750 = {
+	.clock = 262750,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 72) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 36044) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 52427),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_267300 = {
+	.clock = 267300,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 74) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 30146) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 36699),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_268500 = {
+	.clock = 268500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 7) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 74) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 45875) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 13107),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_296703 = {
+	.clock = 296703,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 86) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 22321) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 36804),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_241500 = {
+	.clock = 241500,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 160) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 39321) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 39320),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_319890 = {
+	.clock = 319890,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 2),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 94) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 64094) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 13631),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_497750 = {
+	.clock = 497750,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 15) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 0),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 166) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 36044) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 52427),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_592000 = {
+	.clock = 592000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 86) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 13107) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 13107),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_593407 = {
+	.clock = 593407,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 0) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 86) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 22328) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 7549),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
+static const struct intel_mpllb_state dg2_hdmi_297 = {
+	.clock = 297000,
+	.ref_control =
+		REG_FIELD_PREP(SNPS_PHY_REF_CONTROL_REF_RANGE, 3),
+	.mpllb_cp =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT, 6) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP, 14) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_INT_GS, 64) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_CP_PROP_GS, 124),
+	.mpllb_div =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_DIV5_CLK_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_TX_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_PMIX_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_V2I, 2) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FREQ_VCO, 3),
+	.mpllb_div2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_REF_CLK_DIV, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_MULTIPLIER, 86) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_HDMI_DIV, 1),
+	.mpllb_fracn1 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_CGG_UPDATE_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_EN, 1) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_DEN, 65535),
+	.mpllb_fracn2 =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_QUOT, 26214) |
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_FRACN_REM, 26214),
+	.mpllb_sscen =
+		REG_FIELD_PREP(SNPS_PHY_MPLLB_SSC_UP_SPREAD, 1),
+};
+
 static const struct intel_mpllb_state dg2_hdmi_594 = {
 	.clock = 594000,
 	.ref_control =
@@ -616,7 +1787,46 @@
 	&dg2_hdmi_27_0,
 	&dg2_hdmi_74_25,
 	&dg2_hdmi_148_5,
+	&dg2_hdmi_297,
 	&dg2_hdmi_594,
+	&dg2_hdmi_25200,
+	&dg2_hdmi_27027,
+	&dg2_hdmi_28320,
+	&dg2_hdmi_30240,
+	&dg2_hdmi_31500,
+	&dg2_hdmi_36000,
+	&dg2_hdmi_40000,
+	&dg2_hdmi_49500,
+	&dg2_hdmi_50000,
+	&dg2_hdmi_57284,
+	&dg2_hdmi_58000,
+	&dg2_hdmi_65000,
+	&dg2_hdmi_71000,
+	&dg2_hdmi_74176,
+	&dg2_hdmi_75000,
+	&dg2_hdmi_78750,
+	&dg2_hdmi_85500,
+	&dg2_hdmi_88750,
+	&dg2_hdmi_106500,
+	&dg2_hdmi_108000,
+	&dg2_hdmi_115500,
+	&dg2_hdmi_119000,
+	&dg2_hdmi_135000,
+	&dg2_hdmi_138500,
+	&dg2_hdmi_147160,
+	&dg2_hdmi_148352,
+	&dg2_hdmi_154000,
+	&dg2_hdmi_162000,
+	&dg2_hdmi_209800,
+	&dg2_hdmi_241500,
+	&dg2_hdmi_262750,
+	&dg2_hdmi_267300,
+	&dg2_hdmi_268500,
+	&dg2_hdmi_296703,
+	&dg2_hdmi_319890,
+	&dg2_hdmi_497750,
+	&dg2_hdmi_592000,
+	&dg2_hdmi_593407,
 	NULL,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_tc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_tc.c
@@ -12,44 +12,81 @@
 static const char *tc_port_mode_name(enum tc_port_mode mode)
 {
 	static const char * const names[] = {
+		[TC_PORT_DISCONNECTED] = "disconnected",
 		[TC_PORT_TBT_ALT] = "tbt-alt",
 		[TC_PORT_DP_ALT] = "dp-alt",
 		[TC_PORT_LEGACY] = "legacy",
 	};
 
 	if (WARN_ON(mode >= ARRAY_SIZE(names)))
-		mode = TC_PORT_TBT_ALT;
+		mode = TC_PORT_DISCONNECTED;
 
 	return names[mode];
 }
 
+static bool intel_tc_port_in_mode(struct intel_digital_port *dig_port,
+				  enum tc_port_mode mode)
+{
+	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
+	enum phy phy = intel_port_to_phy(i915, dig_port->base.port);
+
+	return intel_phy_is_tc(i915, phy) && dig_port->tc_mode == mode;
+}
+
+bool intel_tc_port_in_tbt_alt_mode(struct intel_digital_port *dig_port)
+{
+	return intel_tc_port_in_mode(dig_port, TC_PORT_TBT_ALT);
+}
+
+bool intel_tc_port_in_dp_alt_mode(struct intel_digital_port *dig_port)
+{
+	return intel_tc_port_in_mode(dig_port, TC_PORT_DP_ALT);
+}
+
+bool intel_tc_port_in_legacy_mode(struct intel_digital_port *dig_port)
+{
+	return intel_tc_port_in_mode(dig_port, TC_PORT_LEGACY);
+}
+
+bool intel_tc_cold_requires_aux_pw(struct intel_digital_port *dig_port)
+{
+	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
+
+	return (DISPLAY_VER(i915) == 11 && dig_port->tc_legacy_port) ||
+		IS_ALDERLAKE_P(i915);
+}
+
 static enum intel_display_power_domain
-tc_cold_get_power_domain(struct intel_digital_port *dig_port)
+tc_cold_get_power_domain(struct intel_digital_port *dig_port, enum tc_port_mode mode)
 {
-	if (intel_tc_cold_requires_aux_pw(dig_port))
-		return intel_legacy_aux_to_power_domain(dig_port->aux_ch);
-	else
+	if (mode == TC_PORT_TBT_ALT || !intel_tc_cold_requires_aux_pw(dig_port))
 		return POWER_DOMAIN_TC_COLD_OFF;
+
+	return intel_legacy_aux_to_power_domain(dig_port->aux_ch);
 }
 
 static intel_wakeref_t
-tc_cold_block(struct intel_digital_port *dig_port)
+tc_cold_block_in_mode(struct intel_digital_port *dig_port, enum tc_port_mode mode,
+		      enum intel_display_power_domain *domain)
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
-	enum intel_display_power_domain domain;
 
-	if (DISPLAY_VER(i915) == 11 && !dig_port->tc_legacy_port)
-		return 0;
+	*domain = tc_cold_get_power_domain(dig_port, mode);
 
-	domain = tc_cold_get_power_domain(dig_port);
-	return intel_display_power_get(i915, domain);
+	return intel_display_power_get(i915, *domain);
+}
+
+static intel_wakeref_t
+tc_cold_block(struct intel_digital_port *dig_port, enum intel_display_power_domain *domain)
+{
+	return tc_cold_block_in_mode(dig_port, dig_port->tc_mode, domain);
 }
 
 static void
-tc_cold_unblock(struct intel_digital_port *dig_port, intel_wakeref_t wakeref)
+tc_cold_unblock(struct intel_digital_port *dig_port, enum intel_display_power_domain domain,
+		intel_wakeref_t wakeref)
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
-	enum intel_display_power_domain domain;
 
 	/*
 	 * wakeref == -1, means some error happened saving save_depot_stack but
@@ -59,8 +96,7 @@
 	if (wakeref == 0)
 		return;
 
-	domain = tc_cold_get_power_domain(dig_port);
-	intel_display_power_put_async(i915, domain, wakeref);
+	intel_display_power_put(i915, domain, wakeref);
 }
 
 static void
@@ -69,11 +105,9 @@
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
 	bool enabled;
 
-	if (DISPLAY_VER(i915) == 11 && !dig_port->tc_legacy_port)
-		return;
-
 	enabled = intel_display_power_is_enabled(i915,
-						 tc_cold_get_power_domain(dig_port));
+						 tc_cold_get_power_domain(dig_port,
+									  dig_port->tc_mode));
 	drm_WARN_ON(&i915->drm, !enabled);
 }
 
@@ -244,6 +278,11 @@
 	struct intel_uncore *uncore = &i915->uncore;
 	u32 val, mask = 0;
 
+	/*
+	 * On ADL-P HW/FW will wake from TCCOLD to complete the read access of
+	 * registers in IOM. Note that this doesn't apply to PHY and FIA
+	 * registers.
+	 */
 	val = intel_uncore_read(uncore, TCSS_DDI_STATUS(tc_port));
 	if (val & TCSS_DDI_STATUS_HPD_LIVE_STATUS_ALT)
 		mask |= BIT(TC_PORT_DP_ALT);
@@ -270,6 +309,14 @@
 	return icl_tc_port_live_status_mask(dig_port);
 }
 
+/*
+ * Return the PHY status complete flag indicating that display can acquire the
+ * PHY ownership. The IOM firmware sets this flag when a DP-alt or legacy sink
+ * is connected and it's ready to switch the ownership to display. The flag
+ * will be left cleared when a TBT-alt sink is connected, where the PHY is
+ * owned by the TBT subsystem and so switching the ownership to display is not
+ * required.
+ */
 static bool icl_tc_phy_status_complete(struct intel_digital_port *dig_port)
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
@@ -288,13 +335,21 @@
 	return val & DP_PHY_MODE_STATUS_COMPLETED(dig_port->tc_phy_fia_idx);
 }
 
+/*
+ * Return the PHY status complete flag indicating that display can acquire the
+ * PHY ownership. The IOM firmware sets this flag when it's ready to switch
+ * the ownership to display, regardless of what sink is connected (TBT-alt,
+ * DP-alt, legacy or nothing). For TBT-alt sinks the PHY is owned by the TBT
+ * subsystem and so switching the ownership to display is not required.
+ */
 static bool adl_tc_phy_status_complete(struct intel_digital_port *dig_port)
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
+	enum tc_port tc_port = intel_port_to_tc(i915, dig_port->base.port);
 	struct intel_uncore *uncore = &i915->uncore;
 	u32 val;
 
-	val = intel_uncore_read(uncore, TCSS_DDI_STATUS(dig_port->tc_phy_fia_idx));
+	val = intel_uncore_read(uncore, TCSS_DDI_STATUS(tc_port));
 	if (val == 0xffffffff) {
 		drm_dbg_kms(&i915->drm,
 			    "Port %s: PHY in TCCOLD, assuming not complete\n",
@@ -339,11 +394,6 @@
 	intel_uncore_write(uncore,
 			   PORT_TX_DFLEXDPCSSS(dig_port->tc_phy_fia), val);
 
-	if (!take && wait_for(!tc_phy_status_complete(dig_port), 10))
-		drm_dbg_kms(&i915->drm,
-			    "Port %s: PHY complete clear timed out\n",
-			    dig_port->tc_port_name);
-
 	return true;
 }
 
@@ -385,9 +435,9 @@
 				PORT_TX_DFLEXDPCSSS(dig_port->tc_phy_fia));
 	if (val == 0xffffffff) {
 		drm_dbg_kms(&i915->drm,
-			    "Port %s: PHY in TCCOLD, assume safe mode\n",
+			    "Port %s: PHY in TCCOLD, assume not owned\n",
 			    dig_port->tc_port_name);
-		return true;
+		return false;
 	}
 
 	return val & DP_PHY_MODE_STATUS_NOT_SAFE(dig_port->tc_phy_fia_idx);
@@ -429,6 +479,7 @@
 			       int required_lanes)
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
+	u32 live_status_mask;
 	int max_lanes;
 
 	if (!tc_phy_status_complete(dig_port)) {
@@ -437,6 +488,13 @@
 		goto out_set_tbt_alt_mode;
 	}
 
+	live_status_mask = tc_port_live_status_mask(dig_port);
+	if (!(live_status_mask & (BIT(TC_PORT_DP_ALT) | BIT(TC_PORT_LEGACY)))) {
+		drm_dbg_kms(&i915->drm, "Port %s: PHY ownership not required (live status %02x)\n",
+			    dig_port->tc_port_name, live_status_mask);
+		goto out_set_tbt_alt_mode;
+	}
+
 	if (!tc_phy_take_ownership(dig_port, true) &&
 	    !drm_WARN_ON(&i915->drm, dig_port->tc_legacy_port))
 		goto out_set_tbt_alt_mode;
@@ -485,14 +543,13 @@
 {
 	switch (dig_port->tc_mode) {
 	case TC_PORT_LEGACY:
-		/* Nothing to do, we never disconnect from legacy mode */
-		break;
 	case TC_PORT_DP_ALT:
 		tc_phy_take_ownership(dig_port, false);
-		dig_port->tc_mode = TC_PORT_TBT_ALT;
-		break;
+		fallthrough;
 	case TC_PORT_TBT_ALT:
-		/* Nothing to do, we stay in TBT-alt mode */
+		dig_port->tc_mode = TC_PORT_DISCONNECTED;
+		fallthrough;
+	case TC_PORT_DISCONNECTED:
 		break;
 	default:
 		MISSING_CASE(dig_port->tc_mode);
@@ -509,6 +566,10 @@
 		return dig_port->tc_mode == TC_PORT_TBT_ALT;
 	}
 
+	/* On ADL-P the PHY complete flag is set in TBT mode as well. */
+	if (IS_ALDERLAKE_P(i915) && dig_port->tc_mode == TC_PORT_TBT_ALT)
+		return true;
+
 	if (!tc_phy_is_owned(dig_port)) {
 		drm_dbg_kms(&i915->drm, "Port %s: PHY not owned\n",
 			    dig_port->tc_port_name);
@@ -550,9 +611,7 @@
 	if (live_status_mask)
 		return fls(live_status_mask) - 1;
 
-	return tc_phy_status_complete(dig_port) &&
-	       dig_port->tc_legacy_port ? TC_PORT_LEGACY :
-					  TC_PORT_TBT_ALT;
+	return TC_PORT_TBT_ALT;
 }
 
 static void intel_tc_port_reset_mode(struct intel_digital_port *dig_port,
@@ -581,6 +640,43 @@
 		    tc_port_mode_name(dig_port->tc_mode));
 }
 
+static bool intel_tc_port_needs_reset(struct intel_digital_port *dig_port)
+{
+	return intel_tc_port_get_target_mode(dig_port) != dig_port->tc_mode;
+}
+
+static void intel_tc_port_update_mode(struct intel_digital_port *dig_port,
+				      int required_lanes, bool force_disconnect)
+{
+	enum intel_display_power_domain domain;
+	intel_wakeref_t wref;
+	bool needs_reset = force_disconnect;
+
+	if (!needs_reset) {
+		/* Get power domain required to check the hotplug live status. */
+		wref = tc_cold_block(dig_port, &domain);
+		needs_reset = intel_tc_port_needs_reset(dig_port);
+		tc_cold_unblock(dig_port, domain, wref);
+	}
+
+	if (!needs_reset)
+		return;
+
+	/* Get power domain required for resetting the mode. */
+	wref = tc_cold_block_in_mode(dig_port, TC_PORT_DISCONNECTED, &domain);
+
+	intel_tc_port_reset_mode(dig_port, required_lanes, force_disconnect);
+
+	/* Get power domain matching the new mode after reset. */
+	tc_cold_unblock(dig_port, dig_port->tc_lock_power_domain,
+			fetch_and_zero(&dig_port->tc_lock_wakeref));
+	if (dig_port->tc_mode != TC_PORT_DISCONNECTED)
+		dig_port->tc_lock_wakeref = tc_cold_block(dig_port,
+							  &dig_port->tc_lock_power_domain);
+
+	tc_cold_unblock(dig_port, domain, wref);
+}
+
 static void
 intel_tc_port_link_init_refcount(struct intel_digital_port *dig_port,
 				 int refcount)
@@ -595,45 +691,42 @@
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
 	struct intel_encoder *encoder = &dig_port->base;
-	intel_wakeref_t tc_cold_wref;
 	int active_links = 0;
 
 	mutex_lock(&dig_port->tc_lock);
-	tc_cold_wref = tc_cold_block(dig_port);
 
-	dig_port->tc_mode = intel_tc_port_get_current_mode(dig_port);
 	if (dig_port->dp.is_mst)
 		active_links = intel_dp_mst_encoder_active_links(dig_port);
 	else if (encoder->base.crtc)
 		active_links = to_intel_crtc(encoder->base.crtc)->active;
 
+	drm_WARN_ON(&i915->drm, dig_port->tc_mode != TC_PORT_DISCONNECTED);
+	drm_WARN_ON(&i915->drm, dig_port->tc_lock_wakeref);
 	if (active_links) {
+		enum intel_display_power_domain domain;
+		intel_wakeref_t tc_cold_wref = tc_cold_block(dig_port, &domain);
+
+		dig_port->tc_mode = intel_tc_port_get_current_mode(dig_port);
+
 		if (!icl_tc_phy_is_connected(dig_port))
 			drm_dbg_kms(&i915->drm,
 				    "Port %s: PHY disconnected with %d active link(s)\n",
 				    dig_port->tc_port_name, active_links);
 		intel_tc_port_link_init_refcount(dig_port, active_links);
 
-		goto out;
-	}
+		dig_port->tc_lock_wakeref = tc_cold_block(dig_port,
+							  &dig_port->tc_lock_power_domain);
 
-	if (dig_port->tc_legacy_port)
-		icl_tc_phy_connect(dig_port, 1);
+		tc_cold_unblock(dig_port, domain, tc_cold_wref);
+	}
 
-out:
 	drm_dbg_kms(&i915->drm, "Port %s: sanitize mode (%s)\n",
 		    dig_port->tc_port_name,
 		    tc_port_mode_name(dig_port->tc_mode));
 
-	tc_cold_unblock(dig_port, tc_cold_wref);
 	mutex_unlock(&dig_port->tc_lock);
 }
 
-static bool intel_tc_port_needs_reset(struct intel_digital_port *dig_port)
-{
-	return intel_tc_port_get_target_mode(dig_port) != dig_port->tc_mode;
-}
-
 /*
  * The type-C ports are different because even when they are connected, they may
  * not be available/usable by the graphics driver: see the comment on
@@ -648,78 +741,79 @@
 {
 	struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
 	bool is_connected;
-	intel_wakeref_t tc_cold_wref;
 
 	intel_tc_port_lock(dig_port);
-	tc_cold_wref = tc_cold_block(dig_port);
 
 	is_connected = tc_port_live_status_mask(dig_port) &
 		       BIT(dig_port->tc_mode);
 
-	tc_cold_unblock(dig_port, tc_cold_wref);
 	intel_tc_port_unlock(dig_port);
 
 	return is_connected;
 }
 
 static void __intel_tc_port_lock(struct intel_digital_port *dig_port,
-				 int required_lanes, bool force_disconnect)
+				 int required_lanes)
 {
 	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
-	intel_wakeref_t wakeref;
-
-	wakeref = intel_display_power_get(i915, POWER_DOMAIN_DISPLAY_CORE);
 
 	mutex_lock(&dig_port->tc_lock);
 
-	if (!dig_port->tc_link_refcount) {
-		intel_wakeref_t tc_cold_wref;
-
-		tc_cold_wref = tc_cold_block(dig_port);
-
-		if (force_disconnect || intel_tc_port_needs_reset(dig_port))
-			intel_tc_port_reset_mode(dig_port, required_lanes,
-						 force_disconnect);
+	cancel_delayed_work(&dig_port->tc_disconnect_phy_work);
 
-		tc_cold_unblock(dig_port, tc_cold_wref);
-	}
-
-	drm_WARN_ON(&i915->drm, dig_port->tc_lock_wakeref);
-	dig_port->tc_lock_wakeref = wakeref;
+	if (!dig_port->tc_link_refcount)
+		intel_tc_port_update_mode(dig_port, required_lanes,
+					  false);
+
+	drm_WARN_ON(&i915->drm, dig_port->tc_mode == TC_PORT_DISCONNECTED);
+	drm_WARN_ON(&i915->drm, dig_port->tc_mode != TC_PORT_TBT_ALT &&
+				!tc_phy_is_owned(dig_port));
 }
 
 void intel_tc_port_lock(struct intel_digital_port *dig_port)
 {
-	__intel_tc_port_lock(dig_port, 1, false);
+	__intel_tc_port_lock(dig_port, 1);
 }
 
-void intel_tc_port_unlock(struct intel_digital_port *dig_port)
+/**
+ * intel_tc_port_disconnect_phy_work: disconnect TypeC PHY from display port
+ * @dig_port: digital port
+ *
+ * Disconnect the given digital port from its TypeC PHY (handing back the
+ * control of the PHY to the TypeC subsystem). This will happen in a delayed
+ * manner after each aux transactions and modeset disables.
+ */
+static void intel_tc_port_disconnect_phy_work(struct work_struct *work)
 {
-	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
-	intel_wakeref_t wakeref = fetch_and_zero(&dig_port->tc_lock_wakeref);
+	struct intel_digital_port *dig_port =
+		container_of(work, struct intel_digital_port, tc_disconnect_phy_work.work);
 
-	mutex_unlock(&dig_port->tc_lock);
+	mutex_lock(&dig_port->tc_lock);
+
+	if (!dig_port->tc_link_refcount)
+		intel_tc_port_update_mode(dig_port, 1, true);
 
-	intel_display_power_put_async(i915, POWER_DOMAIN_DISPLAY_CORE,
-				      wakeref);
+	mutex_unlock(&dig_port->tc_lock);
 }
 
 /**
- * intel_tc_port_disconnect_phy: disconnect TypeC PHY from display port
+ * intel_tc_port_flush_work: flush the work disconnecting the PHY
  * @dig_port: digital port
  *
- * Disconnect the given digital port from its TypeC PHY (handing back the
- * control of the PHY to the TypeC subsystem). The only purpose of this
- * function is to force the disconnect even with a TypeC display output still
- * plugged to the TypeC connector, which is required by the TypeC firmwares
- * during system suspend and shutdown. Otherwise - during the unplug event
- * handling - the PHY ownership is released automatically by
- * intel_tc_port_reset_mode(), when calling this function is not required.
+ * Flush the delayed work disconnecting an idle PHY.
  */
-void intel_tc_port_disconnect_phy(struct intel_digital_port *dig_port)
+void intel_tc_port_flush_work(struct intel_digital_port *dig_port)
 {
-	__intel_tc_port_lock(dig_port, 1, true);
-	intel_tc_port_unlock(dig_port);
+	flush_delayed_work(&dig_port->tc_disconnect_phy_work);
+}
+
+void intel_tc_port_unlock(struct intel_digital_port *dig_port)
+{
+	if (!dig_port->tc_link_refcount && dig_port->tc_mode != TC_PORT_DISCONNECTED)
+		queue_delayed_work(system_unbound_wq, &dig_port->tc_disconnect_phy_work,
+				   msecs_to_jiffies(1000));
+
+	mutex_unlock(&dig_port->tc_lock);
 }
 
 bool intel_tc_port_ref_held(struct intel_digital_port *dig_port)
@@ -731,21 +825,30 @@
 void intel_tc_port_get_link(struct intel_digital_port *dig_port,
 			    int required_lanes)
 {
-	__intel_tc_port_lock(dig_port, required_lanes, false);
+	__intel_tc_port_lock(dig_port, required_lanes);
 	dig_port->tc_link_refcount++;
 	intel_tc_port_unlock(dig_port);
 }
 
 void intel_tc_port_put_link(struct intel_digital_port *dig_port)
 {
-	mutex_lock(&dig_port->tc_lock);
-	dig_port->tc_link_refcount--;
-	mutex_unlock(&dig_port->tc_lock);
+	intel_tc_port_lock(dig_port);
+	--dig_port->tc_link_refcount;
+	intel_tc_port_unlock(dig_port);
+
+	/*
+	 * Disconnecting the PHY after the PHY's PLL gets disabled may
+	 * hang the system on ADL-P, so disconnect the PHY here synchronously.
+	 * TODO: remove this once the root cause of the ordering requirement
+	 * is found/fixed.
+	 */
+	intel_tc_port_flush_work(dig_port);
 }
 
 static bool
 tc_has_modular_fia(struct drm_i915_private *i915, struct intel_digital_port *dig_port)
 {
+	enum intel_display_power_domain domain;
 	intel_wakeref_t wakeref;
 	u32 val;
 
@@ -753,9 +856,9 @@
 		return false;
 
 	mutex_lock(&dig_port->tc_lock);
-	wakeref = tc_cold_block(dig_port);
+	wakeref = tc_cold_block(dig_port, &domain);
 	val = intel_uncore_read(&i915->uncore, PORT_TX_DFLEXDPSP(FIA1));
-	tc_cold_unblock(dig_port, wakeref);
+	tc_cold_unblock(dig_port, domain, wakeref);
 	mutex_unlock(&dig_port->tc_lock);
 
 	drm_WARN_ON(&i915->drm, val == 0xffffffff);
@@ -795,15 +898,9 @@
 		 "%c/TC#%d", port_name(port), tc_port + 1);
 
 	mutex_init(&dig_port->tc_lock);
+	INIT_DELAYED_WORK(&dig_port->tc_disconnect_phy_work, intel_tc_port_disconnect_phy_work);
 	dig_port->tc_legacy_port = is_legacy;
+	dig_port->tc_mode = TC_PORT_DISCONNECTED;
 	dig_port->tc_link_refcount = 0;
 	tc_port_load_fia_params(i915, dig_port);
 }
-
-bool intel_tc_cold_requires_aux_pw(struct intel_digital_port *dig_port)
-{
-	struct drm_i915_private *i915 = to_i915(dig_port->base.base.dev);
-
-	return (DISPLAY_VER(i915) == 11 && dig_port->tc_legacy_port) ||
-		IS_ALDERLAKE_P(i915);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_tc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_tc.h
@@ -12,8 +12,11 @@
 struct intel_digital_port;
 struct intel_encoder;
 
+bool intel_tc_port_in_tbt_alt_mode(struct intel_digital_port *dig_port);
+bool intel_tc_port_in_dp_alt_mode(struct intel_digital_port *dig_port);
+bool intel_tc_port_in_legacy_mode(struct intel_digital_port *dig_port);
+
 bool intel_tc_port_connected(struct intel_encoder *encoder);
-void intel_tc_port_disconnect_phy(struct intel_digital_port *dig_port);
 
 u32 intel_tc_port_get_lane_mask(struct intel_digital_port *dig_port);
 u32 intel_tc_port_get_pin_assignment_mask(struct intel_digital_port *dig_port);
@@ -24,6 +27,7 @@
 void intel_tc_port_sanitize(struct intel_digital_port *dig_port);
 void intel_tc_port_lock(struct intel_digital_port *dig_port);
 void intel_tc_port_unlock(struct intel_digital_port *dig_port);
+void intel_tc_port_flush_work(struct intel_digital_port *dig_port);
 void intel_tc_port_get_link(struct intel_digital_port *dig_port,
 			    int required_lanes);
 void intel_tc_port_put_link(struct intel_digital_port *dig_port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_tv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_tv.c
@@ -955,8 +955,14 @@
 intel_tv_mode_valid(struct drm_connector *connector,
 		    struct drm_display_mode *mode)
 {
+	struct drm_i915_private *i915 = to_i915(connector->dev);
 	const struct tv_mode *tv_mode = intel_tv_mode_find(connector->state);
-	int max_dotclk = to_i915(connector->dev)->max_dotclk_freq;
+	int max_dotclk = i915->max_dotclk_freq;
+	enum drm_mode_status status;
+
+	status = intel_cpu_transcoder_mode_valid(i915, mode);
+	if (status != MODE_OK)
+		return status;
 
 	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
 		return MODE_NO_DBLESCAN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/intel_vbt_defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/intel_vbt_defs.h
@@ -307,6 +307,9 @@
 #define HDMI_MAX_DATA_RATE_PLATFORM	0			/* 204 */
 #define HDMI_MAX_DATA_RATE_297		1			/* 204 */
 #define HDMI_MAX_DATA_RATE_165		2			/* 204 */
+#define HDMI_MAX_DATA_RATE_594		3			/* 249 */
+#define HDMI_MAX_DATA_RATE_340		4			/* 249 */
+#define HDMI_MAX_DATA_RATE_300		5			/* 249 */
 
 #define LEGACY_CHILD_DEVICE_CONFIG_SIZE		33
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/skl_scaler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/skl_scaler.c
@@ -294,6 +294,263 @@
 	return 0;
 }
 
+static int intel_atomic_setup_scaler(struct intel_crtc_scaler_state *scaler_state,
+				     int num_scalers_need, struct intel_crtc *intel_crtc,
+				     const char *name, int idx,
+				     struct intel_plane_state *plane_state,
+				     int *scaler_id)
+{
+	struct drm_i915_private *dev_priv = to_i915(intel_crtc->base.dev);
+	int j;
+	u32 mode;
+
+	if (*scaler_id < 0) {
+		/* find a free scaler */
+		for (j = 0; j < intel_crtc->num_scalers; j++) {
+			if (scaler_state->scalers[j].in_use)
+				continue;
+
+			*scaler_id = j;
+			scaler_state->scalers[*scaler_id].in_use = 1;
+			break;
+		}
+	}
+
+	if (drm_WARN(&dev_priv->drm, *scaler_id < 0,
+		     "Cannot find scaler for %s:%d\n", name, idx))
+		return -EINVAL;
+
+	/* set scaler mode */
+	if (plane_state && plane_state->hw.fb &&
+	    plane_state->hw.fb->format->is_yuv &&
+	    plane_state->hw.fb->format->num_planes > 1) {
+		struct intel_plane *plane = to_intel_plane(plane_state->uapi.plane);
+
+		if (DISPLAY_VER(dev_priv) == 9) {
+			mode = SKL_PS_SCALER_MODE_NV12;
+		} else if (icl_is_hdr_plane(dev_priv, plane->id)) {
+			/*
+			 * On gen11+'s HDR planes we only use the scaler for
+			 * scaling. They have a dedicated chroma upsampler, so
+			 * we don't need the scaler to upsample the UV plane.
+			 */
+			mode = PS_SCALER_MODE_NORMAL;
+		} else {
+			struct intel_plane *linked =
+				plane_state->planar_linked_plane;
+
+			mode = PS_SCALER_MODE_PLANAR;
+
+			if (linked)
+				mode |= PS_PLANE_Y_SEL(linked->id);
+		}
+	} else if (DISPLAY_VER(dev_priv) >= 10) {
+		mode = PS_SCALER_MODE_NORMAL;
+	} else if (num_scalers_need == 1 && intel_crtc->num_scalers > 1) {
+		/*
+		 * when only 1 scaler is in use on a pipe with 2 scalers
+		 * scaler 0 operates in high quality (HQ) mode.
+		 * In this case use scaler 0 to take advantage of HQ mode
+		 */
+		scaler_state->scalers[*scaler_id].in_use = 0;
+		*scaler_id = 0;
+		scaler_state->scalers[0].in_use = 1;
+		mode = SKL_PS_SCALER_MODE_HQ;
+	} else {
+		mode = SKL_PS_SCALER_MODE_DYN;
+	}
+
+	/*
+	 * FIXME: we should also check the scaler factors for pfit, so
+	 * this shouldn't be tied directly to planes.
+	 */
+	if (plane_state && plane_state->hw.fb) {
+		const struct drm_framebuffer *fb = plane_state->hw.fb;
+		const struct drm_rect *src = &plane_state->uapi.src;
+		const struct drm_rect *dst = &plane_state->uapi.dst;
+		int hscale, vscale, max_vscale, max_hscale;
+
+		/*
+		 * FIXME: When two scalers are needed, but only one of
+		 * them needs to downscale, we should make sure that
+		 * the one that needs downscaling support is assigned
+		 * as the first scaler, so we don't reject downscaling
+		 * unnecessarily.
+		 */
+
+		if (DISPLAY_VER(dev_priv) >= 14) {
+			/*
+			 * On versions 14 and up, only the first
+			 * scaler supports a vertical scaling factor
+			 * of more than 1.0, while a horizontal
+			 * scaling factor of 3.0 is supported.
+			 */
+			max_hscale = 0x30000 - 1;
+			if (*scaler_id == 0)
+				max_vscale = 0x30000 - 1;
+			else
+				max_vscale = 0x10000;
+
+		} else if (DISPLAY_VER(dev_priv) >= 10 ||
+			   !intel_format_info_is_yuv_semiplanar(fb->format, fb->modifier)) {
+			max_hscale = 0x30000 - 1;
+			max_vscale = 0x30000 - 1;
+		} else {
+			max_hscale = 0x20000 - 1;
+			max_vscale = 0x20000 - 1;
+		}
+
+		/*
+		 * FIXME: We should change the if-else block above to
+		 * support HQ vs dynamic scaler properly.
+		 */
+
+		/* Check if required scaling is within limits */
+		hscale = drm_rect_calc_hscale(src, dst, 1, max_hscale);
+		vscale = drm_rect_calc_vscale(src, dst, 1, max_vscale);
+
+		if (hscale < 0 || vscale < 0) {
+			drm_dbg_kms(&dev_priv->drm,
+				    "Scaler %d doesn't support required plane scaling\n",
+				    *scaler_id);
+			drm_rect_debug_print("src: ", src, true);
+			drm_rect_debug_print("dst: ", dst, false);
+
+			return -EINVAL;
+		}
+	}
+
+	drm_dbg_kms(&dev_priv->drm, "Attached scaler id %u.%u to %s:%d\n",
+		    intel_crtc->pipe, *scaler_id, name, idx);
+	scaler_state->scalers[*scaler_id].mode = mode;
+
+	return 0;
+}
+
+/**
+ * intel_atomic_setup_scalers() - setup scalers for crtc per staged requests
+ * @dev_priv: i915 device
+ * @intel_crtc: intel crtc
+ * @crtc_state: incoming crtc_state to validate and setup scalers
+ *
+ * This function sets up scalers based on staged scaling requests for
+ * a @crtc and its planes. It is called from crtc level check path. If request
+ * is a supportable request, it attaches scalers to requested planes and crtc.
+ *
+ * This function takes into account the current scaler(s) in use by any planes
+ * not being part of this atomic state
+ *
+ *  Returns:
+ *         0 - scalers were setup successfully
+ *         error code - otherwise
+ */
+int intel_atomic_setup_scalers(struct drm_i915_private *dev_priv,
+			       struct intel_crtc *intel_crtc,
+			       struct intel_crtc_state *crtc_state)
+{
+	struct drm_plane *plane = NULL;
+	struct intel_plane *intel_plane;
+	struct intel_crtc_scaler_state *scaler_state =
+		&crtc_state->scaler_state;
+	struct drm_atomic_state *drm_state = crtc_state->uapi.state;
+	struct intel_atomic_state *intel_state = to_intel_atomic_state(drm_state);
+	int num_scalers_need;
+	int i;
+
+	num_scalers_need = hweight32(scaler_state->scaler_users);
+
+	/*
+	 * High level flow:
+	 * - staged scaler requests are already in scaler_state->scaler_users
+	 * - check whether staged scaling requests can be supported
+	 * - add planes using scalers that aren't in current transaction
+	 * - assign scalers to requested users
+	 * - as part of plane commit, scalers will be committed
+	 *   (i.e., either attached or detached) to respective planes in hw
+	 * - as part of crtc_commit, scaler will be either attached or detached
+	 *   to crtc in hw
+	 */
+
+	/* fail if required scalers > available scalers */
+	if (num_scalers_need > intel_crtc->num_scalers) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "Too many scaling requests %d > %d\n",
+			    num_scalers_need, intel_crtc->num_scalers);
+		return -EINVAL;
+	}
+
+	/* walkthrough scaler_users bits and start assigning scalers */
+	for (i = 0; i < sizeof(scaler_state->scaler_users) * 8; i++) {
+		struct intel_plane_state *plane_state = NULL;
+		int *scaler_id;
+		const char *name;
+		int idx, ret;
+
+		/* skip if scaler not required */
+		if (!(scaler_state->scaler_users & (1 << i)))
+			continue;
+
+		if (i == SKL_CRTC_INDEX) {
+			name = "CRTC";
+			idx = intel_crtc->base.base.id;
+
+			/* panel fitter case: assign as a crtc scaler */
+			scaler_id = &scaler_state->scaler_id;
+		} else {
+			name = "PLANE";
+
+			/* plane scaler case: assign as a plane scaler */
+			/* find the plane that set the bit as scaler_user */
+			plane = drm_state->planes[i].ptr;
+
+			/*
+			 * to enable/disable hq mode, add planes that are using scaler
+			 * into this transaction
+			 */
+			if (!plane) {
+				struct drm_plane_state *state;
+
+				/*
+				 * GLK+ scalers don't have a HQ mode so it
+				 * isn't necessary to change between HQ and dyn mode
+				 * on those platforms.
+				 */
+				if (DISPLAY_VER(dev_priv) >= 10)
+					continue;
+
+				plane = drm_plane_from_index(&dev_priv->drm, i);
+				state = drm_atomic_get_plane_state(drm_state, plane);
+				if (IS_ERR(state)) {
+					drm_dbg_kms(&dev_priv->drm,
+						    "Failed to add [PLANE:%d] to drm_state\n",
+						    plane->base.id);
+					return PTR_ERR(state);
+				}
+			}
+
+			intel_plane = to_intel_plane(plane);
+			idx = plane->base.id;
+
+			/* plane on different crtc cannot be a scaler user of this crtc */
+			if (drm_WARN_ON(&dev_priv->drm,
+					intel_plane->pipe != intel_crtc->pipe))
+				continue;
+
+			plane_state = intel_atomic_get_new_plane_state(intel_state,
+								       intel_plane);
+			scaler_id = &plane_state->scaler_id;
+		}
+
+		ret = intel_atomic_setup_scaler(scaler_state, num_scalers_need,
+						intel_crtc, name, idx,
+						plane_state, scaler_id);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
 static int glk_coef_tap(int i)
 {
 	return i % 7;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/skl_scaler.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/skl_scaler.h
@@ -8,17 +8,22 @@
 #include <linux/types.h>
 
 enum drm_scaling_filter;
+enum pipe;
 struct drm_i915_private;
+struct intel_crtc;
 struct intel_crtc_state;
-struct intel_plane_state;
 struct intel_plane;
-enum pipe;
+struct intel_plane_state;
 
 int skl_update_scaler_crtc(struct intel_crtc_state *crtc_state);
 
 int skl_update_scaler_plane(struct intel_crtc_state *crtc_state,
 			    struct intel_plane_state *plane_state);
 
+int intel_atomic_setup_scalers(struct drm_i915_private *dev_priv,
+			       struct intel_crtc *intel_crtc,
+			       struct intel_crtc_state *crtc_state);
+
 void skl_pfit_enable(const struct intel_crtc_state *crtc_state);
 
 void skl_program_plane_scaler(struct intel_plane *plane,
@@ -26,4 +31,5 @@
 			      const struct intel_plane_state *plane_state);
 void skl_detach_scalers(const struct intel_crtc_state *crtc_state);
 void skl_scaler_disable(const struct intel_crtc_state *old_crtc_state);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/skl_universal_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/skl_universal_plane.c
@@ -98,8 +98,6 @@
 	DRM_FORMAT_Y216,
 	DRM_FORMAT_XYUV8888,
 	DRM_FORMAT_XVYU2101010,
-	DRM_FORMAT_XVYU12_16161616,
-	DRM_FORMAT_XVYU16161616,
 };
 
 static const u32 icl_sdr_uv_plane_formats[] = {
@@ -126,8 +124,6 @@
 	DRM_FORMAT_Y216,
 	DRM_FORMAT_XYUV8888,
 	DRM_FORMAT_XVYU2101010,
-	DRM_FORMAT_XVYU12_16161616,
-	DRM_FORMAT_XVYU16161616,
 };
 
 static const u32 icl_hdr_plane_formats[] = {
@@ -1473,7 +1469,7 @@
 	u32 offset;
 	int ret;
 
-	if (w > max_width || w < min_width || h > max_height) {
+	if (w > max_width || w < min_width || h > max_height || h < 1) {
 		drm_dbg_kms(&dev_priv->drm,
 			    "requested Y/RGB source size %dx%d outside limits (min: %dx1 max: %dx%d)\n",
 			    w, h, min_width, max_width, max_height);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/display/vlv_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/display/vlv_dsi.c
@@ -32,6 +32,7 @@
 
 #include "i915_drv.h"
 #include "intel_atomic.h"
+#include "intel_backlight.h"
 #include "intel_connector.h"
 #include "intel_crtc.h"
 #include "intel_de.h"
@@ -1612,9 +1613,25 @@
 	.destroy = intel_dsi_encoder_destroy,
 };
 
+static enum drm_mode_status vlv_dsi_mode_valid(struct drm_connector *connector,
+					       struct drm_display_mode *mode)
+{
+	struct drm_i915_private *i915 = to_i915(connector->dev);
+
+	if (IS_VALLEYVIEW(i915) || IS_CHERRYVIEW(i915)) {
+		enum drm_mode_status status;
+
+		status = intel_cpu_transcoder_mode_valid(i915, mode);
+		if (status != MODE_OK)
+			return status;
+	}
+
+	return intel_dsi_mode_valid(connector, mode);
+}
+
 static const struct drm_connector_helper_funcs intel_dsi_connector_helper_funcs = {
 	.get_modes = intel_dsi_get_modes,
-	.mode_valid = intel_dsi_mode_valid,
+	.mode_valid = vlv_dsi_mode_valid,
 	.atomic_check = intel_digital_connector_atomic_check,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_context.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_context.c
@@ -442,6 +442,13 @@
 	u16 idx, num_bonds;
 	int err, n;
 
+	if (GRAPHICS_VER(i915) >= 12 && !IS_TIGERLAKE(i915) &&
+	    !IS_ROCKETLAKE(i915) && !IS_ALDERLAKE_S(i915)) {
+		drm_dbg(&i915->drm,
+			"Bonding on gen12+ aside from TGL, RKL, and ADL_S not supported\n");
+		return -ENODEV;
+	}
+
 	if (get_user(idx, &ext->virtual_index))
 		return -EFAULT;
 
@@ -635,6 +642,7 @@
 		if (idx >= pc->num_user_engines)
 			return -EINVAL;
 
+		idx = array_index_nospec(idx, pc->num_user_engines);
 		pe = &pc->user_engines[idx];
 
 		/* Only render engine supports RPCS configuration. */
@@ -720,8 +728,9 @@
 	case I915_CONTEXT_PARAM_PERSISTENCE:
 		if (args->size)
 			ret = -EINVAL;
-		ret = proto_context_set_persistence(fpriv->dev_priv, pc,
-						    args->value);
+		else
+			ret = proto_context_set_persistence(fpriv->dev_priv, pc,
+							    args->value);
 		break;
 
 	case I915_CONTEXT_PARAM_NO_ZEROMAP:
@@ -989,6 +998,10 @@
 	trace_i915_context_free(ctx);
 	GEM_BUG_ON(!i915_gem_context_is_closed(ctx));
 
+	spin_lock(&ctx->i915->gem.contexts.lock);
+	list_del(&ctx->link);
+	spin_unlock(&ctx->i915->gem.contexts.lock);
+
 	if (ctx->syncobj)
 		drm_syncobj_put(ctx->syncobj);
 
@@ -1220,10 +1233,6 @@
 	 */
 	lut_close(ctx);
 
-	spin_lock(&ctx->i915->gem.contexts.lock);
-	list_del(&ctx->link);
-	spin_unlock(&ctx->i915->gem.contexts.lock);
-
 	mutex_unlock(&ctx->mutex);
 
 	/*
@@ -1427,6 +1436,10 @@
 	init_contexts(&i915->gem.contexts);
 }
 
+/*
+ * Note that this implicitly consumes the ctx reference, by placing
+ * the ctx in the context_xa.
+ */
 static void gem_context_register(struct i915_gem_context *ctx,
 				 struct drm_i915_file_private *fpriv,
 				 u32 id)
@@ -1440,13 +1453,13 @@
 	snprintf(ctx->name, sizeof(ctx->name), "%s[%d]",
 		 current->comm, pid_nr(ctx->pid));
 
-	/* And finally expose ourselves to userspace via the idr */
-	old = xa_store(&fpriv->context_xa, id, ctx, GFP_KERNEL);
-	WARN_ON(old);
-
 	spin_lock(&i915->gem.contexts.lock);
 	list_add_tail(&ctx->link, &i915->gem.contexts.list);
 	spin_unlock(&i915->gem.contexts.lock);
+
+	/* And finally expose ourselves to userspace via the idr */
+	old = xa_store(&fpriv->context_xa, id, ctx, GFP_KERNEL);
+	WARN_ON(old);
 }
 
 int i915_gem_context_open(struct drm_i915_private *i915,
@@ -1923,14 +1936,22 @@
 	if (IS_ERR(ctx))
 		return ctx;
 
+	/*
+	 * One for the xarray and one for the caller.  We need to grab
+	 * the reference *prior* to making the ctx visble to userspace
+	 * in gem_context_register(), as at any point after that
+	 * userspace can try to race us with another thread destroying
+	 * the context under our feet.
+	 */
+	i915_gem_context_get(ctx);
+
 	gem_context_register(ctx, file_priv, id);
 
 	old = xa_erase(&file_priv->proto_context_xa, id);
 	GEM_BUG_ON(old != pc);
 	proto_context_close(pc);
 
-	/* One for the xarray and one for the caller */
-	return i915_gem_context_get(ctx);
+	return ctx;
 }
 
 struct i915_gem_context *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_dmabuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_dmabuf.c
@@ -34,13 +34,13 @@
 		goto err;
 	}
 
-	ret = sg_alloc_table(st, obj->mm.pages->nents, GFP_KERNEL);
+	ret = sg_alloc_table(st, obj->mm.pages->orig_nents, GFP_KERNEL);
 	if (ret)
 		goto err_free;
 
 	src = obj->mm.pages->sgl;
 	dst = st->sgl;
-	for (i = 0; i < obj->mm.pages->nents; i++) {
+	for (i = 0; i < obj->mm.pages->orig_nents; i++) {
 		sg_set_page(dst, sg_page(src), src->length, 0);
 		dst = sg_next(dst);
 		src = sg_next(src);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c
@@ -1060,6 +1060,47 @@
 	return &i915->ggtt;
 }
 
+static void reloc_cache_unmap(struct reloc_cache *cache)
+{
+	void *vaddr;
+
+	if (!cache->vaddr)
+		return;
+
+	vaddr = unmask_page(cache->vaddr);
+	if (cache->vaddr & KMAP)
+		kunmap_atomic(vaddr);
+	else
+		io_mapping_unmap_atomic((void __iomem *)vaddr);
+}
+
+static void reloc_cache_remap(struct reloc_cache *cache,
+			      struct drm_i915_gem_object *obj)
+{
+	void *vaddr;
+
+	if (!cache->vaddr)
+		return;
+
+	if (cache->vaddr & KMAP) {
+		struct page *page = i915_gem_object_get_page(obj, cache->page);
+
+		vaddr = kmap_atomic(page);
+		cache->vaddr = unmask_flags(cache->vaddr) |
+			(unsigned long)vaddr;
+	} else {
+		struct i915_ggtt *ggtt = cache_to_ggtt(cache);
+		unsigned long offset;
+
+		offset = cache->node.start;
+		if (!drm_mm_node_allocated(&cache->node))
+			offset += cache->page << PAGE_SHIFT;
+
+		cache->vaddr = (unsigned long)
+			io_mapping_map_atomic_wc(&ggtt->iomap, offset);
+	}
+}
+
 static void reloc_cache_reset(struct reloc_cache *cache, struct i915_execbuffer *eb)
 {
 	void *vaddr;
@@ -1324,10 +1365,17 @@
 		 * batchbuffers.
 		 */
 		if (reloc->write_domain == I915_GEM_DOMAIN_INSTRUCTION &&
-		    GRAPHICS_VER(eb->i915) == 6) {
+		    GRAPHICS_VER(eb->i915) == 6 &&
+		    !i915_vma_is_bound(target->vma, I915_VMA_GLOBAL_BIND)) {
+			struct i915_vma *vma = target->vma;
+
+			reloc_cache_unmap(&eb->reloc_cache);
+			mutex_lock(&vma->vm->mutex);
 			err = i915_vma_bind(target->vma,
 					    target->vma->obj->cache_level,
 					    PIN_GLOBAL, NULL);
+			mutex_unlock(&vma->vm->mutex);
+			reloc_cache_remap(&eb->reloc_cache, ev->vma->obj);
 			if (err)
 				return err;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_internal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_internal.c
@@ -143,24 +143,10 @@
 	.put_pages = i915_gem_object_put_pages_internal,
 };
 
-/**
- * i915_gem_object_create_internal: create an object with volatile pages
- * @i915: the i915 device
- * @size: the size in bytes of backing storage to allocate for the object
- *
- * Creates a new object that wraps some internal memory for private use.
- * This object is not backed by swappable storage, and as such its contents
- * are volatile and only valid whilst pinned. If the object is reaped by the
- * shrinker, its pages and data will be discarded. Equally, it is not a full
- * GEM object and so not valid for access from userspace. This makes it useful
- * for hardware interfaces like ringbuffers (which are pinned from the time
- * the request is written to the time the hardware stops accessing it), but
- * not for contexts (which need to be preserved when not active for later
- * reuse). Note that it is not cleared upon allocation.
- */
 struct drm_i915_gem_object *
-i915_gem_object_create_internal(struct drm_i915_private *i915,
-				phys_addr_t size)
+__i915_gem_object_create_internal(struct drm_i915_private *i915,
+				  const struct drm_i915_gem_object_ops *ops,
+				  phys_addr_t size)
 {
 	static struct lock_class_key lock_class;
 	struct drm_i915_gem_object *obj;
@@ -177,7 +163,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	drm_gem_private_object_init(&i915->drm, &obj->base, size);
-	i915_gem_object_init(obj, &i915_gem_object_internal_ops, &lock_class, 0);
+	i915_gem_object_init(obj, ops, &lock_class, 0);
 	obj->mem_flags |= I915_BO_FLAG_STRUCT_PAGE;
 
 	/*
@@ -197,3 +183,25 @@
 
 	return obj;
 }
+
+/**
+ * i915_gem_object_create_internal: create an object with volatile pages
+ * @i915: the i915 device
+ * @size: the size in bytes of backing storage to allocate for the object
+ *
+ * Creates a new object that wraps some internal memory for private use.
+ * This object is not backed by swappable storage, and as such its contents
+ * are volatile and only valid whilst pinned. If the object is reaped by the
+ * shrinker, its pages and data will be discarded. Equally, it is not a full
+ * GEM object and so not valid for access from userspace. This makes it useful
+ * for hardware interfaces like ringbuffers (which are pinned from the time
+ * the request is written to the time the hardware stops accessing it), but
+ * not for contexts (which need to be preserved when not active for later
+ * reuse). Note that it is not cleared upon allocation.
+ */
+struct drm_i915_gem_object *
+i915_gem_object_create_internal(struct drm_i915_private *i915,
+				phys_addr_t size)
+{
+	return __i915_gem_object_create_internal(i915, &i915_gem_object_internal_ops, size);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_mman.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_mman.c
@@ -66,7 +66,7 @@
 	 * mmap ioctl is disallowed for all discrete platforms,
 	 * and for all platforms with GRAPHICS_VER > 12.
 	 */
-	if (IS_DGFX(i915) || GRAPHICS_VER(i915) > 12)
+	if (IS_DGFX(i915) || GRAPHICS_VER_FULL(i915) > IP_VER(12, 0))
 		return -EOPNOTSUPP;
 
 	if (args->flags & ~(I915_MMAP_WC))
@@ -231,6 +231,7 @@
 	case 0:
 	case -EAGAIN:
 	case -ENOSPC: /* transient failure to evict? */
+	case -ENOBUFS: /* temporarily out of fences? */
 	case -ERESTARTSYS:
 	case -EINTR:
 	case -EBUSY:
@@ -285,6 +286,41 @@
 	return i915_error_to_vmf_fault(err);
 }
 
+static void set_address_limits(struct vm_area_struct *area,
+			       struct i915_vma *vma,
+			       unsigned long obj_offset,
+			       unsigned long *start_vaddr,
+			       unsigned long *end_vaddr)
+{
+	unsigned long vm_start, vm_end, vma_size; /* user's memory parameters */
+	long start, end; /* memory boundaries */
+
+	/*
+	 * Let's move into the ">> PAGE_SHIFT"
+	 * domain to be sure not to lose bits
+	 */
+	vm_start = area->vm_start >> PAGE_SHIFT;
+	vm_end = area->vm_end >> PAGE_SHIFT;
+	vma_size = vma->size >> PAGE_SHIFT;
+
+	/*
+	 * Calculate the memory boundaries by considering the offset
+	 * provided by the user during memory mapping and the offset
+	 * provided for the partial mapping.
+	 */
+	start = vm_start;
+	start -= obj_offset;
+	start += vma->ggtt_view.partial.offset;
+	end = start + vma_size;
+
+	start = max_t(long, start, vm_start);
+	end = min_t(long, end, vm_end);
+
+	/* Let's move back into the "<< PAGE_SHIFT" domain */
+	*start_vaddr = (unsigned long)start << PAGE_SHIFT;
+	*end_vaddr = (unsigned long)end << PAGE_SHIFT;
+}
+
 static vm_fault_t vm_fault_gtt(struct vm_fault *vmf)
 {
 #define MIN_CHUNK_PAGES (SZ_1M >> PAGE_SHIFT)
@@ -297,14 +333,18 @@
 	struct i915_ggtt *ggtt = &i915->ggtt;
 	bool write = area->vm_flags & VM_WRITE;
 	struct i915_gem_ww_ctx ww;
+	unsigned long obj_offset;
+	unsigned long start, end; /* memory boundaries */
 	intel_wakeref_t wakeref;
 	struct i915_vma *vma;
 	pgoff_t page_offset;
+	unsigned long pfn;
 	int srcu;
 	int ret;
 
-	/* We don't use vmf->pgoff since that has the fake offset */
+	obj_offset = area->vm_pgoff - drm_vma_node_start(&mmo->vma_node);
 	page_offset = (vmf->address - area->vm_start) >> PAGE_SHIFT;
+	page_offset += obj_offset;
 
 	trace_i915_gem_object_fault(obj, page_offset, true, write);
 
@@ -375,12 +415,14 @@
 	if (ret)
 		goto err_unpin;
 
+	set_address_limits(area, vma, obj_offset, &start, &end);
+
+	pfn = (ggtt->gmadr.start + i915_ggtt_offset(vma)) >> PAGE_SHIFT;
+	pfn += (start - area->vm_start) >> PAGE_SHIFT;
+	pfn += obj_offset - vma->ggtt_view.partial.offset;
+
 	/* Finally, remap it using the new GTT offset */
-	ret = remap_io_mapping(area,
-			       area->vm_start + (vma->ggtt_view.partial.offset << PAGE_SHIFT),
-			       (ggtt->gmadr.start + vma->node.start) >> PAGE_SHIFT,
-			       min_t(u64, vma->size, area->vm_end - area->vm_start),
-			       &ggtt->iomap);
+	ret = remap_io_mapping(area, start, pfn, end - start, &ggtt->iomap);
 	if (ret)
 		goto err_fence;
 
@@ -438,7 +480,7 @@
 		return -EACCES;
 
 	addr -= area->vm_start;
-	if (addr >= obj->base.size)
+	if (range_overflows_t(u64, addr, len, obj->base.size))
 		return -EINVAL;
 
 	i915_gem_ww_ctx_init(&ww, true);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_object.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_object.c
@@ -224,6 +224,12 @@
 			GEM_BUG_ON(vma->obj != obj);
 			spin_unlock(&obj->vma.lock);
 
+			/* Verify that the vma is unbound under the vm mutex. */
+			mutex_lock(&vma->vm->mutex);
+			atomic_and(~I915_VMA_PIN_MASK, &vma->flags);
+			__i915_vma_unbind(vma);
+			mutex_unlock(&vma->vm->mutex);
+
 			__i915_vma_put(vma);
 
 			spin_lock(&obj->vma.lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_object_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_object_types.h
@@ -298,6 +298,7 @@
 			     I915_BO_ALLOC_USER)
 #define I915_BO_READONLY         BIT(4)
 #define I915_TILING_QUIRK_BIT    5 /* unknown swizzling; do not release! */
+#define I915_BO_WAS_BOUND_BIT    6
 
 	/**
 	 * @mem_flags - Mutable placement-related flags
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_pages.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_pages.c
@@ -10,6 +10,8 @@
 #include "i915_gem_lmem.h"
 #include "i915_gem_mman.h"
 
+#include "gt/intel_gt.h"
+
 void __i915_gem_object_set_pages(struct drm_i915_gem_object *obj,
 				 struct sg_table *pages,
 				 unsigned int sg_page_sizes)
@@ -160,7 +162,6 @@
 /* Immediately discard the backing storage */
 void i915_gem_object_truncate(struct drm_i915_gem_object *obj)
 {
-	drm_gem_free_mmap_offset(&obj->base);
 	if (obj->ops->truncate)
 		obj->ops->truncate(obj);
 }
@@ -218,6 +219,14 @@
 	__i915_gem_object_reset_page_iter(obj);
 	obj->mm.page_sizes.phys = obj->mm.page_sizes.sg = 0;
 
+	if (test_and_clear_bit(I915_BO_WAS_BOUND_BIT, &obj->flags)) {
+		struct drm_i915_private *i915 = to_i915(obj->base.dev);
+		intel_wakeref_t wakeref;
+
+		with_intel_runtime_pm_if_active(&i915->runtime_pm, wakeref)
+			intel_gt_invalidate_tlbs(&i915->gt);
+	}
+
 	return pages;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_shmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_shmem.c
@@ -533,7 +533,7 @@
 	mapping_set_gfp_mask(mapping, mask);
 	GEM_BUG_ON(!(mapping_gfp_mask(mapping) & __GFP_RECLAIM));
 
-	i915_gem_object_init(obj, &i915_gem_shmem_ops, &lock_class, 0);
+	i915_gem_object_init(obj, &i915_gem_shmem_ops, &lock_class, flags);
 	obj->mem_flags |= I915_BO_FLAG_STRUCT_PAGE;
 	obj->write_domain = I915_GEM_DOMAIN_CPU;
 	obj->read_domains = I915_GEM_DOMAIN_CPU;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_tiling.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_tiling.c
@@ -294,10 +294,6 @@
 	spin_unlock(&obj->vma.lock);
 
 	obj->tiling_and_stride = tiling | stride;
-	i915_gem_object_unlock(obj);
-
-	/* Force the fence to be reacquired for GTT access */
-	i915_gem_object_release_mmap_gtt(obj);
 
 	/* Try to preallocate memory required to save swizzling on put-pages */
 	if (i915_gem_object_needs_bit17_swizzle(obj)) {
@@ -310,6 +306,11 @@
 		obj->bit_17 = NULL;
 	}
 
+	i915_gem_object_unlock(obj);
+
+	/* Force the fence to be reacquired for GTT access */
+	i915_gem_object_release_mmap_gtt(obj);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_ttm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_ttm.c
@@ -759,11 +759,9 @@
 	if (obj->mm.madv != I915_MADV_WILLNEED) {
 		bo->priority = I915_TTM_PRIO_PURGE;
 	} else if (!i915_gem_object_has_pages(obj)) {
-		if (bo->priority < I915_TTM_PRIO_HAS_PAGES)
-			bo->priority = I915_TTM_PRIO_HAS_PAGES;
+		bo->priority = I915_TTM_PRIO_NO_PAGES;
 	} else {
-		if (bo->priority > I915_TTM_PRIO_NO_PAGES)
-			bo->priority = I915_TTM_PRIO_NO_PAGES;
+		bo->priority = I915_TTM_PRIO_HAS_PAGES;
 	}
 
 	ttm_bo_move_to_lru_tail(bo, bo->resource, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/i915_gem_userptr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/i915_gem_userptr.c
@@ -374,6 +374,9 @@
 {
 	GEM_WARN_ON(obj->userptr.page_ref);
 
+	if (!obj->userptr.notifier.mm)
+		return;
+
 	mmu_interval_notifier_remove(&obj->userptr.notifier);
 	obj->userptr.notifier.mm = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gem/selftests/i915_gem_context.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gem/selftests/i915_gem_context.c
@@ -182,97 +182,108 @@
 }
 
 struct parallel_switch {
-	struct task_struct *tsk;
+	struct kthread_worker *worker;
+	struct kthread_work work;
 	struct intel_context *ce[2];
+	int result;
 };
 
-static int __live_parallel_switch1(void *data)
+static void __live_parallel_switch1(struct kthread_work *work)
 {
-	struct parallel_switch *arg = data;
+	struct parallel_switch *arg =
+		container_of(work, typeof(*arg), work);
 	IGT_TIMEOUT(end_time);
 	unsigned long count;
 
 	count = 0;
+	arg->result = 0;
 	do {
 		struct i915_request *rq = NULL;
-		int err, n;
+		int n;
 
-		err = 0;
-		for (n = 0; !err && n < ARRAY_SIZE(arg->ce); n++) {
+		for (n = 0; !arg->result && n < ARRAY_SIZE(arg->ce); n++) {
 			struct i915_request *prev = rq;
 
 			rq = i915_request_create(arg->ce[n]);
 			if (IS_ERR(rq)) {
 				i915_request_put(prev);
-				return PTR_ERR(rq);
+				arg->result = PTR_ERR(rq);
+				break;
 			}
 
 			i915_request_get(rq);
 			if (prev) {
-				err = i915_request_await_dma_fence(rq, &prev->fence);
+				arg->result =
+					i915_request_await_dma_fence(rq,
+								     &prev->fence);
 				i915_request_put(prev);
 			}
 
 			i915_request_add(rq);
 		}
-		if (i915_request_wait(rq, 0, HZ / 5) < 0)
-			err = -ETIME;
+
+		if (IS_ERR_OR_NULL(rq))
+			break;
+
+		if (i915_request_wait(rq, 0, HZ) < 0)
+			arg->result = -ETIME;
+
 		i915_request_put(rq);
-		if (err)
-			return err;
 
 		count++;
-	} while (!__igt_timeout(end_time, NULL));
+	} while (!arg->result && !__igt_timeout(end_time, NULL));
 
-	pr_info("%s: %lu switches (sync)\n", arg->ce[0]->engine->name, count);
-	return 0;
+	pr_info("%s: %lu switches (sync) <%d>\n",
+		arg->ce[0]->engine->name, count, arg->result);
 }
 
-static int __live_parallel_switchN(void *data)
+static void __live_parallel_switchN(struct kthread_work *work)
 {
-	struct parallel_switch *arg = data;
+	struct parallel_switch *arg =
+		container_of(work, typeof(*arg), work);
 	struct i915_request *rq = NULL;
 	IGT_TIMEOUT(end_time);
 	unsigned long count;
 	int n;
 
 	count = 0;
+	arg->result = 0;
 	do {
-		for (n = 0; n < ARRAY_SIZE(arg->ce); n++) {
+		for (n = 0; !arg->result && n < ARRAY_SIZE(arg->ce); n++) {
 			struct i915_request *prev = rq;
-			int err = 0;
 
 			rq = i915_request_create(arg->ce[n]);
 			if (IS_ERR(rq)) {
 				i915_request_put(prev);
-				return PTR_ERR(rq);
+				arg->result = PTR_ERR(rq);
+				break;
 			}
 
 			i915_request_get(rq);
 			if (prev) {
-				err = i915_request_await_dma_fence(rq, &prev->fence);
+				arg->result =
+					i915_request_await_dma_fence(rq,
+								     &prev->fence);
 				i915_request_put(prev);
 			}
 
 			i915_request_add(rq);
-			if (err) {
-				i915_request_put(rq);
-				return err;
-			}
 		}
 
 		count++;
-	} while (!__igt_timeout(end_time, NULL));
-	i915_request_put(rq);
+	} while (!arg->result && !__igt_timeout(end_time, NULL));
+
+	if (!IS_ERR_OR_NULL(rq))
+		i915_request_put(rq);
 
-	pr_info("%s: %lu switches (many)\n", arg->ce[0]->engine->name, count);
-	return 0;
+	pr_info("%s: %lu switches (many) <%d>\n",
+		arg->ce[0]->engine->name, count, arg->result);
 }
 
 static int live_parallel_switch(void *arg)
 {
 	struct drm_i915_private *i915 = arg;
-	static int (* const func[])(void *arg) = {
+	static void (* const func[])(struct kthread_work *) = {
 		__live_parallel_switch1,
 		__live_parallel_switchN,
 		NULL,
@@ -280,7 +291,7 @@
 	struct parallel_switch *data = NULL;
 	struct i915_gem_engines *engines;
 	struct i915_gem_engines_iter it;
-	int (* const *fn)(void *arg);
+	void (* const *fn)(struct kthread_work *);
 	struct i915_gem_context *ctx;
 	struct intel_context *ce;
 	struct file *file;
@@ -338,8 +349,10 @@
 				continue;
 
 			ce = intel_context_create(data[m].ce[0]->engine);
-			if (IS_ERR(ce))
+			if (IS_ERR(ce)) {
+				err = PTR_ERR(ce);
 				goto out;
+			}
 
 			err = intel_context_pin(ce);
 			if (err) {
@@ -351,9 +364,24 @@
 		}
 	}
 
+	for (n = 0; n < count; n++) {
+		struct kthread_worker *worker;
+
+		if (!data[n].ce[0])
+			continue;
+
+		worker = kthread_create_worker(0, "igt/parallel:%s",
+					       data[n].ce[0]->engine->name);
+		if (IS_ERR(worker)) {
+			err = PTR_ERR(worker);
+			goto out;
+		}
+
+		data[n].worker = worker;
+	}
+
 	for (fn = func; !err && *fn; fn++) {
 		struct igt_live_test t;
-		int n;
 
 		err = igt_live_test_begin(&t, i915, __func__, "");
 		if (err)
@@ -363,34 +391,23 @@
 			if (!data[n].ce[0])
 				continue;
 
-			data[n].tsk = kthread_run(*fn, &data[n],
-						  "igt/parallel:%s",
-						  data[n].ce[0]->engine->name);
-			if (IS_ERR(data[n].tsk)) {
-				err = PTR_ERR(data[n].tsk);
-				break;
-			}
-			get_task_struct(data[n].tsk);
+			data[n].result = 0;
+			kthread_init_work(&data[n].work, *fn);
+			kthread_queue_work(data[n].worker, &data[n].work);
 		}
 
-		yield(); /* start all threads before we kthread_stop() */
-
 		for (n = 0; n < count; n++) {
-			int status;
-
-			if (IS_ERR_OR_NULL(data[n].tsk))
-				continue;
-
-			status = kthread_stop(data[n].tsk);
-			if (status && !err)
-				err = status;
-
-			put_task_struct(data[n].tsk);
-			data[n].tsk = NULL;
+			if (data[n].ce[0]) {
+				kthread_flush_work(&data[n].work);
+				if (data[n].result && !err)
+					err = data[n].result;
+			}
 		}
 
-		if (igt_live_test_end(&t))
-			err = -EIO;
+		if (igt_live_test_end(&t)) {
+			err = err ?: -EIO;
+			break;
+		}
 	}
 
 out:
@@ -402,6 +419,9 @@
 			intel_context_unpin(data[n].ce[m]);
 			intel_context_put(data[n].ce[m]);
 		}
+
+		if (data[n].worker)
+			kthread_destroy_worker(data[n].worker);
 	}
 	kfree(data);
 out_file:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/gen6_ppgtt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/gen6_ppgtt.c
@@ -244,6 +244,7 @@
 	i915_gem_object_put(vm->scratch[1]);
 err_scratch0:
 	i915_gem_object_put(vm->scratch[0]);
+	vm->scratch[0] = NULL;
 	return ret;
 }
 
@@ -262,15 +263,13 @@
 {
 	struct gen6_ppgtt *ppgtt = to_gen6_ppgtt(i915_vm_to_ppgtt(vm));
 
-	__i915_vma_put(ppgtt->vma);
-
 	gen6_ppgtt_free_pd(ppgtt);
 	free_scratch(vm);
 
-	mutex_destroy(&ppgtt->flush);
-	mutex_destroy(&ppgtt->pin_mutex);
+	if (ppgtt->base.pd)
+		free_pd(&ppgtt->base.vm, ppgtt->base.pd);
 
-	free_pd(&ppgtt->base.vm, ppgtt->base.pd);
+	mutex_destroy(&ppgtt->flush);
 }
 
 static int pd_vma_set_pages(struct i915_vma *vma)
@@ -331,37 +330,6 @@
 	.unbind_vma = pd_vma_unbind,
 };
 
-static struct i915_vma *pd_vma_create(struct gen6_ppgtt *ppgtt, int size)
-{
-	struct i915_ggtt *ggtt = ppgtt->base.vm.gt->ggtt;
-	struct i915_vma *vma;
-
-	GEM_BUG_ON(!IS_ALIGNED(size, I915_GTT_PAGE_SIZE));
-	GEM_BUG_ON(size > ggtt->vm.total);
-
-	vma = i915_vma_alloc();
-	if (!vma)
-		return ERR_PTR(-ENOMEM);
-
-	i915_active_init(&vma->active, NULL, NULL, 0);
-
-	kref_init(&vma->ref);
-	mutex_init(&vma->pages_mutex);
-	vma->vm = i915_vm_get(&ggtt->vm);
-	vma->ops = &pd_vma_ops;
-	vma->private = ppgtt;
-
-	vma->size = size;
-	vma->fence_size = size;
-	atomic_set(&vma->flags, I915_VMA_GGTT);
-	vma->ggtt_view.type = I915_GGTT_VIEW_ROTATED; /* prevent fencing */
-
-	INIT_LIST_HEAD(&vma->obj_link);
-	INIT_LIST_HEAD(&vma->closed_link);
-
-	return vma;
-}
-
 int gen6_ppgtt_pin(struct i915_ppgtt *base, struct i915_gem_ww_ctx *ww)
 {
 	struct gen6_ppgtt *ppgtt = to_gen6_ppgtt(base);
@@ -378,24 +346,85 @@
 	if (atomic_add_unless(&ppgtt->pin_count, 1, 0))
 		return 0;
 
-	if (mutex_lock_interruptible(&ppgtt->pin_mutex))
-		return -EINTR;
+	/* grab the ppgtt resv to pin the object */
+	err = i915_vm_lock_objects(&ppgtt->base.vm, ww);
+	if (err)
+		return err;
 
 	/*
 	 * PPGTT PDEs reside in the GGTT and consists of 512 entries. The
 	 * allocator works in address space sizes, so it's multiplied by page
 	 * size. We allocate at the top of the GTT to avoid fragmentation.
 	 */
-	err = 0;
-	if (!atomic_read(&ppgtt->pin_count))
+	if (!atomic_read(&ppgtt->pin_count)) {
 		err = i915_ggtt_pin(ppgtt->vma, ww, GEN6_PD_ALIGN, PIN_HIGH);
+
+		GEM_BUG_ON(ppgtt->vma->fence);
+		clear_bit(I915_VMA_CAN_FENCE_BIT, __i915_vma_flags(ppgtt->vma));
+	}
 	if (!err)
 		atomic_inc(&ppgtt->pin_count);
-	mutex_unlock(&ppgtt->pin_mutex);
 
 	return err;
 }
 
+static int pd_dummy_obj_get_pages(struct drm_i915_gem_object *obj)
+{
+	obj->mm.pages = ZERO_SIZE_PTR;
+	return 0;
+}
+
+static void pd_dummy_obj_put_pages(struct drm_i915_gem_object *obj,
+				   struct sg_table *pages)
+{
+}
+
+static const struct drm_i915_gem_object_ops pd_dummy_obj_ops = {
+	.name = "pd_dummy_obj",
+	.get_pages = pd_dummy_obj_get_pages,
+	.put_pages = pd_dummy_obj_put_pages,
+};
+
+static struct i915_page_directory *
+gen6_alloc_top_pd(struct gen6_ppgtt *ppgtt)
+{
+	struct i915_ggtt * const ggtt = ppgtt->base.vm.gt->ggtt;
+	struct i915_page_directory *pd;
+	int err;
+
+	pd = __alloc_pd(I915_PDES);
+	if (unlikely(!pd))
+		return ERR_PTR(-ENOMEM);
+
+	pd->pt.base = __i915_gem_object_create_internal(ppgtt->base.vm.gt->i915,
+							&pd_dummy_obj_ops,
+							I915_PDES * SZ_4K);
+	if (IS_ERR(pd->pt.base)) {
+		err = PTR_ERR(pd->pt.base);
+		pd->pt.base = NULL;
+		goto err_pd;
+	}
+
+	pd->pt.base->base.resv = i915_vm_resv_get(&ppgtt->base.vm);
+	pd->pt.base->shares_resv_from = &ppgtt->base.vm;
+
+	ppgtt->vma = i915_vma_instance(pd->pt.base, &ggtt->vm, NULL);
+	if (IS_ERR(ppgtt->vma)) {
+		err = PTR_ERR(ppgtt->vma);
+		ppgtt->vma = NULL;
+		goto err_pd;
+	}
+
+	/* The dummy object we create is special, override ops.. */
+	ppgtt->vma->ops = &pd_vma_ops;
+	ppgtt->vma->private = ppgtt;
+	return pd;
+
+err_pd:
+	free_pd(&ppgtt->base.vm, pd);
+	return ERR_PTR(err);
+}
+
 void gen6_ppgtt_unpin(struct i915_ppgtt *base)
 {
 	struct gen6_ppgtt *ppgtt = to_gen6_ppgtt(base);
@@ -427,7 +456,6 @@
 		return ERR_PTR(-ENOMEM);
 
 	mutex_init(&ppgtt->flush);
-	mutex_init(&ppgtt->pin_mutex);
 
 	ppgtt_init(&ppgtt->base, gt);
 	ppgtt->base.vm.pd_shift = ilog2(SZ_4K * SZ_4K / sizeof(gen6_pte_t));
@@ -442,30 +470,19 @@
 	ppgtt->base.vm.alloc_pt_dma = alloc_pt_dma;
 	ppgtt->base.vm.pte_encode = ggtt->vm.pte_encode;
 
-	ppgtt->base.pd = __alloc_pd(I915_PDES);
-	if (!ppgtt->base.pd) {
-		err = -ENOMEM;
-		goto err_free;
-	}
-
 	err = gen6_ppgtt_init_scratch(ppgtt);
 	if (err)
-		goto err_pd;
+		goto err_put;
 
-	ppgtt->vma = pd_vma_create(ppgtt, GEN6_PD_SIZE);
-	if (IS_ERR(ppgtt->vma)) {
-		err = PTR_ERR(ppgtt->vma);
-		goto err_scratch;
+	ppgtt->base.pd = gen6_alloc_top_pd(ppgtt);
+	if (IS_ERR(ppgtt->base.pd)) {
+		err = PTR_ERR(ppgtt->base.pd);
+		goto err_put;
 	}
 
 	return &ppgtt->base;
 
-err_scratch:
-	free_scratch(&ppgtt->base.vm);
-err_pd:
-	free_pd(&ppgtt->base.vm, ppgtt->base.pd);
-err_free:
-	mutex_destroy(&ppgtt->pin_mutex);
-	kfree(ppgtt);
+err_put:
+	i915_vm_put(&ppgtt->base.vm);
 	return ERR_PTR(err);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/gen6_ppgtt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/gen6_ppgtt.h
@@ -19,7 +19,6 @@
 	u32 pp_dir;
 
 	atomic_t pin_count;
-	struct mutex pin_mutex;
 
 	bool scan_for_unused_pt;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/gen8_ppgtt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/gen8_ppgtt.c
@@ -196,7 +196,10 @@
 	if (intel_vgpu_active(vm->i915))
 		gen8_ppgtt_notify_vgt(ppgtt, false);
 
-	__gen8_ppgtt_cleanup(vm, ppgtt->pd, gen8_pd_top_count(vm), vm->top);
+	if (ppgtt->pd)
+		__gen8_ppgtt_cleanup(vm, ppgtt->pd,
+				     gen8_pd_top_count(vm), vm->top);
+
 	free_scratch(vm);
 }
 
@@ -656,8 +659,10 @@
 		struct drm_i915_gem_object *obj;
 
 		obj = vm->alloc_pt_dma(vm, I915_GTT_PAGE_SIZE_4K);
-		if (IS_ERR(obj))
+		if (IS_ERR(obj)) {
+			ret = PTR_ERR(obj);
 			goto free_scratch;
+		}
 
 		ret = map_pt_dma(vm, obj);
 		if (ret) {
@@ -676,7 +681,8 @@
 free_scratch:
 	while (i--)
 		i915_gem_object_put(vm->scratch[i]);
-	return -ENOMEM;
+	vm->scratch[0] = NULL;
+	return ret;
 }
 
 static int gen8_preallocate_top_level_pdp(struct i915_ppgtt *ppgtt)
@@ -753,6 +759,7 @@
  */
 struct i915_ppgtt *gen8_ppgtt_create(struct intel_gt *gt)
 {
+	struct i915_page_directory *pd;
 	struct i915_ppgtt *ppgtt;
 	int err;
 
@@ -779,44 +786,39 @@
 	else
 		ppgtt->vm.alloc_pt_dma = alloc_pt_dma;
 
+	ppgtt->vm.pte_encode = gen8_pte_encode;
+
+	ppgtt->vm.bind_async_flags = I915_VMA_LOCAL_BIND;
+	ppgtt->vm.insert_entries = gen8_ppgtt_insert;
+	ppgtt->vm.insert_page = gen8_ppgtt_insert_entry;
+	ppgtt->vm.allocate_va_range = gen8_ppgtt_alloc;
+	ppgtt->vm.clear_range = gen8_ppgtt_clear;
+	ppgtt->vm.foreach = gen8_ppgtt_foreach;
+	ppgtt->vm.cleanup = gen8_ppgtt_cleanup;
+
 	err = gen8_init_scratch(&ppgtt->vm);
 	if (err)
-		goto err_free;
+		goto err_put;
 
-	ppgtt->pd = gen8_alloc_top_pd(&ppgtt->vm);
-	if (IS_ERR(ppgtt->pd)) {
-		err = PTR_ERR(ppgtt->pd);
-		goto err_free_scratch;
+	pd = gen8_alloc_top_pd(&ppgtt->vm);
+	if (IS_ERR(pd)) {
+		err = PTR_ERR(pd);
+		goto err_put;
 	}
+	ppgtt->pd = pd;
 
 	if (!i915_vm_is_4lvl(&ppgtt->vm)) {
 		err = gen8_preallocate_top_level_pdp(ppgtt);
 		if (err)
-			goto err_free_pd;
+			goto err_put;
 	}
 
-	ppgtt->vm.bind_async_flags = I915_VMA_LOCAL_BIND;
-	ppgtt->vm.insert_entries = gen8_ppgtt_insert;
-	ppgtt->vm.insert_page = gen8_ppgtt_insert_entry;
-	ppgtt->vm.allocate_va_range = gen8_ppgtt_alloc;
-	ppgtt->vm.clear_range = gen8_ppgtt_clear;
-	ppgtt->vm.foreach = gen8_ppgtt_foreach;
-
-	ppgtt->vm.pte_encode = gen8_pte_encode;
-
 	if (intel_vgpu_active(gt->i915))
 		gen8_ppgtt_notify_vgt(ppgtt, true);
 
-	ppgtt->vm.cleanup = gen8_ppgtt_cleanup;
-
 	return ppgtt;
 
-err_free_pd:
-	__gen8_ppgtt_cleanup(&ppgtt->vm, ppgtt->pd,
-			     gen8_pd_top_count(&ppgtt->vm), ppgtt->vm.top);
-err_free_scratch:
-	free_scratch(&ppgtt->vm);
-err_free:
-	kfree(ppgtt);
+err_put:
+	i915_vm_put(&ppgtt->vm);
 	return ERR_PTR(err);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_breadcrumbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_breadcrumbs.c
@@ -257,8 +257,13 @@
 		i915_request_put(rq);
 	}
 
+	/* Lazy irq enabling after HW submission */
 	if (!READ_ONCE(b->irq_armed) && !list_empty(&b->signalers))
 		intel_breadcrumbs_arm_irq(b);
+
+	/* And confirm that we still want irqs enabled before we yield */
+	if (READ_ONCE(b->irq_armed) && !atomic_read(&b->active))
+		intel_breadcrumbs_disarm_irq(b);
 }
 
 struct intel_breadcrumbs *
@@ -309,13 +314,7 @@
 		return;
 
 	/* Kick the work once more to drain the signalers, and disarm the irq */
-	irq_work_sync(&b->irq_work);
-	while (READ_ONCE(b->irq_armed) && !atomic_read(&b->active)) {
-		local_irq_disable();
-		signal_irq_work(&b->irq_work);
-		local_irq_enable();
-		cond_resched();
-	}
+	irq_work_queue(&b->irq_work);
 }
 
 void intel_breadcrumbs_free(struct kref *kref)
@@ -398,7 +397,8 @@
 	 * the request as it may have completed and raised the interrupt as
 	 * we were attaching it into the lists.
 	 */
-	irq_work_queue(&b->irq_work);
+	if (!READ_ONCE(b->irq_armed) || __i915_request_is_complete(rq))
+		irq_work_queue(&b->irq_work);
 }
 
 bool i915_request_enable_breadcrumb(struct i915_request *rq)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_context_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_context_types.h
@@ -152,6 +152,14 @@
 	/** sseu: Control eu/slice partitioning */
 	struct intel_sseu sseu;
 
+	/**
+	 * pinned_contexts_link: List link for the engine's pinned contexts.
+	 * This is only used if this is a perma-pinned kernel context and
+	 * the list is assumed to only be manipulated during driver load
+	 * or unload time so no mutex protection currently.
+	 */
+	struct list_head pinned_contexts_link;
+
 	u8 wa_bb_page; /* if set, page num reserved for context workarounds */
 
 	struct {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_engine_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_engine_cs.c
@@ -320,6 +320,7 @@
 
 	BUILD_BUG_ON(BITS_PER_TYPE(engine->mask) < I915_NUM_ENGINES);
 
+	INIT_LIST_HEAD(&engine->pinned_contexts_list);
 	engine->id = id;
 	engine->legacy_idx = INVALID_ENGINE;
 	engine->mask = BIT(id);
@@ -875,6 +876,8 @@
 		return ERR_PTR(err);
 	}
 
+	list_add_tail(&ce->pinned_contexts_link, &engine->pinned_contexts_list);
+
 	/*
 	 * Give our perma-pinned kernel timelines a separate lockdep class,
 	 * so that we can use them from within the normal user timelines
@@ -897,6 +900,7 @@
 	list_del(&ce->timeline->engine_link);
 	mutex_unlock(&hwsp->vm->mutex);
 
+	list_del(&ce->pinned_contexts_link);
 	intel_context_unpin(ce);
 	intel_context_put(ce);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_engine_pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_engine_pm.c
@@ -274,9 +274,6 @@
 	intel_engine_park_heartbeat(engine);
 	intel_breadcrumbs_park(engine->breadcrumbs);
 
-	/* Must be reset upon idling, or we may miss the busy wakeup. */
-	GEM_BUG_ON(engine->sched_engine->queue_priority_hint != INT_MIN);
-
 	if (engine->park)
 		engine->park(engine);
 
@@ -298,6 +295,29 @@
 	intel_engine_init_heartbeat(engine);
 }
 
+/**
+ * intel_engine_reset_pinned_contexts - Reset the pinned contexts of
+ * an engine.
+ * @engine: The engine whose pinned contexts we want to reset.
+ *
+ * Typically the pinned context LMEM images lose or get their content
+ * corrupted on suspend. This function resets their images.
+ */
+void intel_engine_reset_pinned_contexts(struct intel_engine_cs *engine)
+{
+	struct intel_context *ce;
+
+	list_for_each_entry(ce, &engine->pinned_contexts_list,
+			    pinned_contexts_link) {
+		/* kernel context gets reset at __engine_unpark() */
+		if (ce == engine->kernel_context)
+			continue;
+
+		dbg_poison_ce(ce);
+		ce->ops->reset(ce);
+	}
+}
+
 #if IS_ENABLED(CONFIG_DRM_I915_SELFTEST)
 #include "selftest_engine_pm.c"
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_engine_pm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_engine_pm.h
@@ -69,4 +69,6 @@
 
 void intel_engine_init__pm(struct intel_engine_cs *engine);
 
+void intel_engine_reset_pinned_contexts(struct intel_engine_cs *engine);
+
 #endif /* INTEL_ENGINE_PM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_engine_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_engine_types.h
@@ -144,6 +144,21 @@
 	struct timer_list preempt;
 
 	/**
+	 * @preempt_target: active request at the time of the preemption request
+	 *
+	 * We force a preemption to occur if the pending contexts have not
+	 * been promoted to active upon receipt of the CS ack event within
+	 * the timeout. This timeout maybe chosen based on the target,
+	 * using a very short timeout if the context is no longer schedulable.
+	 * That short timeout may not be applicable to other contexts, so
+	 * if a context switch should happen within before the preemption
+	 * timeout, we may shoot early at an innocent context. To prevent this,
+	 * we record which context was active at the time of the preemption
+	 * request and only reset that context upon the timeout.
+	 */
+	const struct i915_request *preempt_target;
+
+	/**
 	 * @ccid: identifier for contexts submitted to this engine
 	 */
 	u32 ccid;
@@ -304,6 +319,13 @@
 
 	struct intel_context *kernel_context; /* pinned */
 
+	/**
+	 * pinned_contexts_list: List of pinned contexts. This list is only
+	 * assumed to be manipulated during driver load- or unload time and
+	 * does therefore not have any additional protection.
+	 */
+	struct list_head pinned_contexts_list;
+
 	intel_engine_mask_t saturated; /* submitting semaphores too late? */
 
 	struct {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_execlists_submission.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_execlists_submission.c
@@ -1225,6 +1225,9 @@
 	if (!rq)
 		return 0;
 
+	/* Only allow ourselves to force reset the currently active context */
+	engine->execlists.preempt_target = rq;
+
 	/* Force a fast reset for terminated contexts (ignoring sysfs!) */
 	if (unlikely(intel_context_is_banned(rq->context) || bad_request(rq)))
 		return 1;
@@ -2140,10 +2143,6 @@
 			if (p->flags & I915_DEPENDENCY_WEAK)
 				continue;
 
-			/* Propagate any change in error status */
-			if (rq->fence.error)
-				i915_request_set_error_once(w, rq->fence.error);
-
 			if (w->engine != rq->engine)
 				continue;
 
@@ -2405,8 +2404,24 @@
 	GEM_BUG_ON(inactive - post > ARRAY_SIZE(post));
 
 	if (unlikely(preempt_timeout(engine))) {
+		const struct i915_request *rq = *engine->execlists.active;
+
+		/*
+		 * If after the preempt-timeout expired, we are still on the
+		 * same active request/context as before we initiated the
+		 * preemption, reset the engine.
+		 *
+		 * However, if we have processed a CS event to switch contexts,
+		 * but not yet processed the CS event for the pending
+		 * preemption, reset the timer allowing the new context to
+		 * gracefully exit.
+		 */
 		cancel_timer(&engine->execlists.preempt);
-		engine->execlists.error_interrupt |= ERROR_PREEMPT;
+		if (rq == engine->execlists.preempt_target)
+			engine->execlists.error_interrupt |= ERROR_PREEMPT;
+		else
+			set_timer_ms(&engine->execlists.preempt,
+				     active_preempt_timeout(engine, rq));
 	}
 
 	if (unlikely(READ_ONCE(engine->execlists.error_interrupt))) {
@@ -2791,6 +2806,8 @@
 
 	/* And scrub the dirty cachelines for the HWSP */
 	clflush_cache_range(engine->status_page.addr, PAGE_SIZE);
+
+	intel_engine_reset_pinned_contexts(engine);
 }
 
 static void enable_error_interrupt(struct intel_engine_cs *engine)
@@ -3171,6 +3188,9 @@
 {
 	cancel_timer(&engine->execlists.timer);
 	cancel_timer(&engine->execlists.preempt);
+
+	/* Reset upon idling, or we may delay the busy wakeup. */
+	WRITE_ONCE(engine->sched_engine->queue_priority_hint, INT_MIN);
 }
 
 static void add_to_engine(struct i915_request *rq)
@@ -3211,11 +3231,7 @@
 
 static bool can_preempt(struct intel_engine_cs *engine)
 {
-	if (GRAPHICS_VER(engine->i915) > 8)
-		return true;
-
-	/* GPGPU on bdw requires extra w/a; not implemented */
-	return engine->class != RENDER_CLASS;
+	return GRAPHICS_VER(engine->i915) > 8;
 }
 
 static void kick_execlists(const struct i915_request *rq, int prio)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c
@@ -291,6 +291,7 @@
 		return;
 
 	GEM_BUG_ON(fence->vma != vma);
+	i915_active_wait(&fence->active);
 	GEM_BUG_ON(!i915_active_is_idle(&fence->active));
 	GEM_BUG_ON(atomic_read(&fence->pin_count));
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_gt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_gt.c
@@ -29,6 +29,8 @@
 
 	spin_lock_init(&gt->irq_lock);
 
+	mutex_init(&gt->tlb_invalidate_lock);
+
 	INIT_LIST_HEAD(&gt->closed_vma);
 	spin_lock_init(&gt->closed_lock);
 
@@ -648,8 +650,13 @@
 			return -EINTR;
 	}
 
-	return timeout ? timeout : intel_uc_wait_for_idle(&gt->uc,
-							  remaining_timeout);
+	if (timeout)
+		return timeout;
+
+	if (remaining_timeout < 0)
+		remaining_timeout = 0;
+
+	return intel_uc_wait_for_idle(&gt->uc, remaining_timeout);
 }
 
 int intel_gt_init(struct intel_gt *gt)
@@ -702,12 +709,12 @@
 	if (err)
 		goto err_gt;
 
-	intel_uc_init_late(&gt->uc);
-
 	err = i915_inject_probe_error(gt->i915, -EIO);
 	if (err)
 		goto err_gt;
 
+	intel_uc_init_late(&gt->uc);
+
 	intel_migrate_init(&gt->migrate, gt);
 
 	goto out_fw;
@@ -895,3 +902,123 @@
 
 	intel_sseu_dump(&info->sseu, p);
 }
+
+struct reg_and_bit {
+	i915_reg_t reg;
+	u32 bit;
+};
+
+static struct reg_and_bit
+get_reg_and_bit(const struct intel_engine_cs *engine, const bool gen8,
+		const i915_reg_t *regs, const unsigned int num)
+{
+	const unsigned int class = engine->class;
+	struct reg_and_bit rb = { };
+
+	if (drm_WARN_ON_ONCE(&engine->i915->drm,
+			     class >= num || !regs[class].reg))
+		return rb;
+
+	rb.reg = regs[class];
+	if (gen8 && class == VIDEO_DECODE_CLASS)
+		rb.reg.reg += 4 * engine->instance; /* GEN8_M2TCR */
+	else
+		rb.bit = engine->instance;
+
+	rb.bit = BIT(rb.bit);
+
+	return rb;
+}
+
+void intel_gt_invalidate_tlbs(struct intel_gt *gt)
+{
+	static const i915_reg_t gen8_regs[] = {
+		[RENDER_CLASS]			= GEN8_RTCR,
+		[VIDEO_DECODE_CLASS]		= GEN8_M1TCR, /* , GEN8_M2TCR */
+		[VIDEO_ENHANCEMENT_CLASS]	= GEN8_VTCR,
+		[COPY_ENGINE_CLASS]		= GEN8_BTCR,
+	};
+	static const i915_reg_t gen12_regs[] = {
+		[RENDER_CLASS]			= GEN12_GFX_TLB_INV_CR,
+		[VIDEO_DECODE_CLASS]		= GEN12_VD_TLB_INV_CR,
+		[VIDEO_ENHANCEMENT_CLASS]	= GEN12_VE_TLB_INV_CR,
+		[COPY_ENGINE_CLASS]		= GEN12_BLT_TLB_INV_CR,
+	};
+	struct drm_i915_private *i915 = gt->i915;
+	struct intel_uncore *uncore = gt->uncore;
+	struct intel_engine_cs *engine;
+	enum intel_engine_id id;
+	const i915_reg_t *regs;
+	unsigned int num = 0;
+
+	if (I915_SELFTEST_ONLY(gt->awake == -ENODEV))
+		return;
+
+	if (intel_gt_is_wedged(gt))
+		return;
+
+	if (GRAPHICS_VER(i915) == 12) {
+		regs = gen12_regs;
+		num = ARRAY_SIZE(gen12_regs);
+	} else if (GRAPHICS_VER(i915) >= 8 && GRAPHICS_VER(i915) <= 11) {
+		regs = gen8_regs;
+		num = ARRAY_SIZE(gen8_regs);
+	} else if (GRAPHICS_VER(i915) < 8) {
+		return;
+	}
+
+	if (drm_WARN_ONCE(&i915->drm, !num,
+			  "Platform does not implement TLB invalidation!"))
+		return;
+
+	GEM_TRACE("\n");
+
+	assert_rpm_wakelock_held(&i915->runtime_pm);
+
+	mutex_lock(&gt->tlb_invalidate_lock);
+	intel_uncore_forcewake_get(uncore, FORCEWAKE_ALL);
+
+	spin_lock_irq(&uncore->lock); /* serialise invalidate with GT reset */
+
+	for_each_engine(engine, gt, id) {
+		struct reg_and_bit rb;
+
+		rb = get_reg_and_bit(engine, regs == gen8_regs, regs, num);
+		if (!i915_mmio_reg_offset(rb.reg))
+			continue;
+
+		if (GRAPHICS_VER(i915) == 12 && (engine->class == VIDEO_DECODE_CLASS ||
+		    engine->class == VIDEO_ENHANCEMENT_CLASS))
+			rb.bit = _MASKED_BIT_ENABLE(rb.bit);
+
+		intel_uncore_write_fw(uncore, rb.reg, rb.bit);
+	}
+
+	spin_unlock_irq(&uncore->lock);
+
+	for_each_engine(engine, gt, id) {
+		/*
+		 * HW architecture suggest typical invalidation time at 40us,
+		 * with pessimistic cases up to 100us and a recommendation to
+		 * cap at 1ms. We go a bit higher just in case.
+		 */
+		const unsigned int timeout_us = 100;
+		const unsigned int timeout_ms = 4;
+		struct reg_and_bit rb;
+
+		rb = get_reg_and_bit(engine, regs == gen8_regs, regs, num);
+		if (!i915_mmio_reg_offset(rb.reg))
+			continue;
+
+		if (__intel_wait_for_register_fw(uncore,
+						 rb.reg, rb.bit, 0,
+						 timeout_us, timeout_ms,
+						 NULL))
+			drm_err_ratelimited(&gt->i915->drm,
+					    "%s TLB invalidation did not complete in %ums!\n",
+					    engine->name, timeout_ms);
+	}
+
+	intel_uncore_forcewake_put_delayed(uncore, FORCEWAKE_ALL);
+	mutex_unlock(&gt->tlb_invalidate_lock);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_gt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_gt.h
@@ -90,4 +90,6 @@
 
 void intel_gt_watchdog_work(struct work_struct *work);
 
+void intel_gt_invalidate_tlbs(struct intel_gt *gt);
+
 #endif /* __INTEL_GT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_gt_requests.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_gt_requests.c
@@ -199,7 +199,7 @@
 	if (remaining_timeout)
 		*remaining_timeout = timeout;
 
-	return active_count ? timeout : 0;
+	return active_count ? timeout ?: -ETIME : 0;
 }
 
 static void retire_work_handler(struct work_struct *work)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_gt_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_gt_types.h
@@ -72,6 +72,8 @@
 
 	struct intel_uc uc;
 
+	struct mutex tlb_invalidate_lock;
+
 	struct intel_gt_timelines {
 		spinlock_t lock; /* protects active_list */
 		struct list_head active_list;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_gtt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_gtt.c
@@ -341,6 +341,9 @@
 {
 	int i;
 
+	if (!vm->scratch[0])
+		return;
+
 	for (i = 0; i <= vm->top; i++)
 		i915_gem_object_put(vm->scratch[i]);
 }
@@ -544,7 +547,7 @@
 	if (IS_ERR(obj))
 		return ERR_CAST(obj);
 
-	i915_gem_object_set_cache_coherency(obj, I915_CACHING_CACHED);
+	i915_gem_object_set_cache_coherency(obj, I915_CACHE_LLC);
 
 	vma = i915_vma_instance(obj, vm, NULL);
 	if (IS_ERR(vma)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_migrate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_migrate.c
@@ -13,7 +13,6 @@
 
 struct insert_pte_data {
 	u64 offset;
-	bool is_lmem;
 };
 
 #define CHUNK_SZ SZ_8M /* ~1ms at 8GiB/s preemption delay */
@@ -40,7 +39,7 @@
 	struct insert_pte_data *d = data;
 
 	vm->insert_page(vm, px_dma(pt), d->offset, I915_CACHE_NONE,
-			d->is_lmem ? PTE_LM : 0);
+			i915_gem_object_is_lmem(pt->base) ? PTE_LM : 0);
 	d->offset += PAGE_SIZE;
 }
 
@@ -134,8 +133,7 @@
 			goto err_vm;
 
 		/* Now allow the GPU to rewrite the PTE via its own ppGTT */
-		d.is_lmem = i915_gem_object_is_lmem(vm->vm.scratch[0]);
-		vm->vm.foreach(&vm->vm, base, base + sz, insert_pte, &d);
+		vm->vm.foreach(&vm->vm, base, d.offset - base, insert_pte, &d);
 	}
 
 	return &vm->vm;
@@ -281,10 +279,10 @@
 	GEM_BUG_ON(GRAPHICS_VER(rq->engine->i915) < 8);
 
 	/* Compute the page directory offset for the target address range */
-	offset += (u64)rq->engine->instance << 32;
 	offset >>= 12;
 	offset *= sizeof(u64);
 	offset += 2 * CHUNK_SZ;
+	offset += (u64)rq->engine->instance << 32;
 
 	cs = intel_ring_begin(rq, 6);
 	if (IS_ERR(cs))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_rc6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_rc6.c
@@ -122,7 +122,7 @@
 		GEN9_MEDIA_PG_ENABLE |
 		GEN11_MEDIA_SAMPLER_PG_ENABLE;
 
-	if (GRAPHICS_VER(gt->i915) >= 12) {
+	if (GRAPHICS_VER(gt->i915) >= 12 && !IS_DG1(gt->i915)) {
 		for (i = 0; i < I915_MAX_VCS; i++)
 			if (HAS_ENGINE(gt, _VCS(i)))
 				pg_enable |= (VDN_HCP_POWERGATE_ENABLE(i) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_reset.c
@@ -271,6 +271,7 @@
 static int gen6_hw_domain_reset(struct intel_gt *gt, u32 hw_domain_mask)
 {
 	struct intel_uncore *uncore = gt->uncore;
+	int loops = 2;
 	int err;
 
 	/*
@@ -278,24 +279,45 @@
 	 * for fifo space for the write or forcewake the chip for
 	 * the read
 	 */
-	intel_uncore_write_fw(uncore, GEN6_GDRST, hw_domain_mask);
+	do {
+		intel_uncore_write_fw(uncore, GEN6_GDRST, hw_domain_mask);
 
-	/* Wait for the device to ack the reset requests */
-	err = __intel_wait_for_register_fw(uncore,
-					   GEN6_GDRST, hw_domain_mask, 0,
-					   500, 0,
-					   NULL);
+		/*
+		 * Wait for the device to ack the reset requests.
+		 *
+		 * On some platforms, e.g. Jasperlake, we see that the
+		 * engine register state is not cleared until shortly after
+		 * GDRST reports completion, causing a failure as we try
+		 * to immediately resume while the internal state is still
+		 * in flux. If we immediately repeat the reset, the second
+		 * reset appears to serialise with the first, and since
+		 * it is a no-op, the registers should retain their reset
+		 * value. However, there is still a concern that upon
+		 * leaving the second reset, the internal engine state
+		 * is still in flux and not ready for resuming.
+		 */
+		err = __intel_wait_for_register_fw(uncore, GEN6_GDRST,
+						   hw_domain_mask, 0,
+						   2000, 0,
+						   NULL);
+	} while (err == 0 && --loops);
 	if (err)
 		GT_TRACE(gt,
 			 "Wait for 0x%08x engines reset failed\n",
 			 hw_domain_mask);
 
+	/*
+	 * As we have observed that the engine state is still volatile
+	 * after GDRST is acked, impose a small delay to let everything settle.
+	 */
+	udelay(50);
+
 	return err;
 }
 
-static int gen6_reset_engines(struct intel_gt *gt,
-			      intel_engine_mask_t engine_mask,
-			      unsigned int retry)
+static int __gen6_reset_engines(struct intel_gt *gt,
+				intel_engine_mask_t engine_mask,
+				unsigned int retry)
 {
 	static const u32 hw_engine_mask[] = {
 		[RCS0]  = GEN6_GRDOM_RENDER,
@@ -322,6 +344,20 @@
 	return gen6_hw_domain_reset(gt, hw_mask);
 }
 
+static int gen6_reset_engines(struct intel_gt *gt,
+			      intel_engine_mask_t engine_mask,
+			      unsigned int retry)
+{
+	unsigned long flags;
+	int ret;
+
+	spin_lock_irqsave(&gt->uncore->lock, flags);
+	ret = __gen6_reset_engines(gt, engine_mask, retry);
+	spin_unlock_irqrestore(&gt->uncore->lock, flags);
+
+	return ret;
+}
+
 static struct intel_engine_cs *find_sfc_paired_vecs_engine(struct intel_engine_cs *engine)
 {
 	int vecs_id;
@@ -488,9 +524,9 @@
 	rmw_clear_fw(uncore, sfc_lock.lock_reg, sfc_lock.lock_bit);
 }
 
-static int gen11_reset_engines(struct intel_gt *gt,
-			       intel_engine_mask_t engine_mask,
-			       unsigned int retry)
+static int __gen11_reset_engines(struct intel_gt *gt,
+				 intel_engine_mask_t engine_mask,
+				 unsigned int retry)
 {
 	static const u32 hw_engine_mask[] = {
 		[RCS0]  = GEN11_GRDOM_RENDER,
@@ -601,8 +637,11 @@
 	struct intel_engine_cs *engine;
 	const bool reset_non_ready = retry >= 1;
 	intel_engine_mask_t tmp;
+	unsigned long flags;
 	int ret;
 
+	spin_lock_irqsave(&gt->uncore->lock, flags);
+
 	for_each_engine_masked(engine, gt, engine_mask, tmp) {
 		ret = gen8_engine_reset_prepare(engine);
 		if (ret && !reset_non_ready)
@@ -623,15 +662,26 @@
 		 */
 	}
 
+	/*
+	 * Wa_22011100796:dg2, whenever Full soft reset is required,
+	 * reset all individual engines firstly, and then do a full soft reset.
+	 *
+	 * This is best effort, so ignore any error from the initial reset.
+	 */
+	if (IS_DG2(gt->i915) && engine_mask == ALL_ENGINES)
+		__gen11_reset_engines(gt, gt->info.engine_mask, 0);
+
 	if (GRAPHICS_VER(gt->i915) >= 11)
-		ret = gen11_reset_engines(gt, engine_mask, retry);
+		ret = __gen11_reset_engines(gt, engine_mask, retry);
 	else
-		ret = gen6_reset_engines(gt, engine_mask, retry);
+		ret = __gen6_reset_engines(gt, engine_mask, retry);
 
 skip_reset:
 	for_each_engine_masked(engine, gt, engine_mask, tmp)
 		gen8_engine_reset_cancel(engine);
 
+	spin_unlock_irqrestore(&gt->uncore->lock, flags);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_ring.c
@@ -113,7 +113,7 @@
 	struct i915_vma *vma;
 
 	obj = i915_gem_object_create_lmem(i915, size, I915_BO_ALLOC_VOLATILE);
-	if (IS_ERR(obj) && i915_ggtt_has_aperture(ggtt))
+	if (IS_ERR(obj) && i915_ggtt_has_aperture(ggtt) && !HAS_LLC(i915))
 		obj = i915_gem_object_create_stolen(i915, size);
 	if (IS_ERR(obj))
 		obj = i915_gem_object_create_internal(i915, size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_ring_submission.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_ring_submission.c
@@ -17,6 +17,7 @@
 #include "intel_ring.h"
 #include "shmem_utils.h"
 #include "intel_engine_heartbeat.h"
+#include "intel_engine_pm.h"
 
 /* Rough estimate of the typical request size, performing a flush,
  * set-context and then emitting the batch.
@@ -291,7 +292,9 @@
 	sanitize_hwsp(engine);
 
 	/* And scrub the dirty cachelines for the HWSP */
-	clflush_cache_range(engine->status_page.addr, PAGE_SIZE);
+	drm_clflush_virt_range(engine->status_page.addr, PAGE_SIZE);
+
+	intel_engine_reset_pinned_contexts(engine);
 }
 
 static void reset_prepare(struct intel_engine_cs *engine)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/intel_workarounds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/intel_workarounds.c
@@ -621,13 +621,6 @@
 	       FF_MODE2_GS_TIMER_MASK,
 	       FF_MODE2_GS_TIMER_224,
 	       0, false);
-
-	/*
-	 * Wa_14012131227:dg1
-	 * Wa_1508744258:tgl,rkl,dg1,adl-s,adl-p
-	 */
-	wa_masked_en(wal, GEN7_COMMON_SLICE_CHICKEN1,
-		     GEN9_RHWO_OPTIMIZATION_DISABLE);
 }
 
 static void dg1_ctx_workarounds_init(struct intel_engine_cs *engine,
@@ -1056,6 +1049,22 @@
 		    GAMT_CHKN_BIT_REG,
 		    GAMT_CHKN_DISABLE_L3_COH_PIPE);
 
+	/*
+	 * Wa_1408615072:icl,ehl  (vsunit)
+	 * Wa_1407596294:icl,ehl  (hsunit)
+	 */
+	wa_write_or(wal, UNSLICE_UNIT_LEVEL_CLKGATE,
+		    VSUNIT_CLKGATE_DIS | HSUNIT_CLKGATE_DIS);
+
+	/* Wa_1407352427:icl,ehl */
+	wa_write_or(wal, UNSLICE_UNIT_LEVEL_CLKGATE2,
+		    PSDUNIT_CLKGATE_DIS);
+
+	/* Wa_1406680159:icl,ehl */
+	wa_write_or(wal,
+		    SUBSLICE_UNIT_LEVEL_CLKGATE,
+		    GWUNIT_CLKGATE_DIS);
+
 	/* Wa_1607087056:icl,ehl,jsl */
 	if (IS_ICELAKE(i915) ||
 	    IS_JSL_EHL_GT_STEP(i915, STEP_A0, STEP_B0))
@@ -1746,22 +1755,6 @@
 			     GEN11_ENABLE_32_PLANE_MODE);
 
 		/*
-		 * Wa_1408615072:icl,ehl  (vsunit)
-		 * Wa_1407596294:icl,ehl  (hsunit)
-		 */
-		wa_write_or(wal, UNSLICE_UNIT_LEVEL_CLKGATE,
-			    VSUNIT_CLKGATE_DIS | HSUNIT_CLKGATE_DIS);
-
-		/* Wa_1407352427:icl,ehl */
-		wa_write_or(wal, UNSLICE_UNIT_LEVEL_CLKGATE2,
-			    PSDUNIT_CLKGATE_DIS);
-
-		/* Wa_1406680159:icl,ehl */
-		wa_write_or(wal,
-			    SUBSLICE_UNIT_LEVEL_CLKGATE,
-			    GWUNIT_CLKGATE_DIS);
-
-		/*
 		 * Wa_1408767742:icl[a2..forever],ehl[all]
 		 * Wa_1605460711:icl[a0..c0]
 		 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/mock_engine.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/mock_engine.c
@@ -376,6 +376,8 @@
 {
 	struct intel_context *ce;
 
+	INIT_LIST_HEAD(&engine->pinned_contexts_list);
+
 	engine->sched_engine = i915_sched_engine_create(ENGINE_MOCK);
 	if (!engine->sched_engine)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/selftest_execlists.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/selftest_execlists.c
@@ -1531,8 +1531,8 @@
 	struct drm_i915_gem_object *obj;
 	struct i915_vma *vma;
 	enum intel_engine_id id;
-	int err = -ENOMEM;
 	u32 *map;
+	int err;
 
 	/*
 	 * Verify that even without HAS_LOGICAL_RING_PREEMPTION, we can
@@ -1540,13 +1540,17 @@
 	 */
 
 	ctx_hi = kernel_context(gt->i915, NULL);
-	if (!ctx_hi)
-		return -ENOMEM;
+	if (IS_ERR(ctx_hi))
+		return PTR_ERR(ctx_hi);
+
 	ctx_hi->sched.priority = I915_CONTEXT_MAX_USER_PRIORITY;
 
 	ctx_lo = kernel_context(gt->i915, NULL);
-	if (!ctx_lo)
+	if (IS_ERR(ctx_lo)) {
+		err = PTR_ERR(ctx_lo);
 		goto err_ctx_hi;
+	}
+
 	ctx_lo->sched.priority = I915_CONTEXT_MIN_USER_PRIORITY;
 
 	obj = i915_gem_object_create_internal(gt->i915, PAGE_SIZE);
@@ -3468,12 +3472,14 @@
 
 struct preempt_smoke {
 	struct intel_gt *gt;
+	struct kthread_work work;
 	struct i915_gem_context **contexts;
 	struct intel_engine_cs *engine;
 	struct drm_i915_gem_object *batch;
 	unsigned int ncontext;
 	struct rnd_state prng;
 	unsigned long count;
+	int result;
 };
 
 static struct i915_gem_context *smoke_context(struct preempt_smoke *smoke)
@@ -3533,34 +3539,31 @@
 	return err;
 }
 
-static int smoke_crescendo_thread(void *arg)
+static void smoke_crescendo_work(struct kthread_work *work)
 {
-	struct preempt_smoke *smoke = arg;
+	struct preempt_smoke *smoke = container_of(work, typeof(*smoke), work);
 	IGT_TIMEOUT(end_time);
 	unsigned long count;
 
 	count = 0;
 	do {
 		struct i915_gem_context *ctx = smoke_context(smoke);
-		int err;
 
-		err = smoke_submit(smoke,
-				   ctx, count % I915_PRIORITY_MAX,
-				   smoke->batch);
-		if (err)
-			return err;
+		smoke->result = smoke_submit(smoke, ctx,
+					     count % I915_PRIORITY_MAX,
+					     smoke->batch);
 
 		count++;
-	} while (count < smoke->ncontext && !__igt_timeout(end_time, NULL));
+	} while (!smoke->result && count < smoke->ncontext &&
+		 !__igt_timeout(end_time, NULL));
 
 	smoke->count = count;
-	return 0;
 }
 
 static int smoke_crescendo(struct preempt_smoke *smoke, unsigned int flags)
 #define BATCH BIT(0)
 {
-	struct task_struct *tsk[I915_NUM_ENGINES] = {};
+	struct kthread_worker *worker[I915_NUM_ENGINES] = {};
 	struct preempt_smoke *arg;
 	struct intel_engine_cs *engine;
 	enum intel_engine_id id;
@@ -3571,6 +3574,8 @@
 	if (!arg)
 		return -ENOMEM;
 
+	memset(arg, 0, I915_NUM_ENGINES * sizeof(*arg));
+
 	for_each_engine(engine, smoke->gt, id) {
 		arg[id] = *smoke;
 		arg[id].engine = engine;
@@ -3578,31 +3583,28 @@
 			arg[id].batch = NULL;
 		arg[id].count = 0;
 
-		tsk[id] = kthread_run(smoke_crescendo_thread, arg,
-				      "igt/smoke:%d", id);
-		if (IS_ERR(tsk[id])) {
-			err = PTR_ERR(tsk[id]);
+		worker[id] = kthread_create_worker(0, "igt/smoke:%d", id);
+		if (IS_ERR(worker[id])) {
+			err = PTR_ERR(worker[id]);
 			break;
 		}
-		get_task_struct(tsk[id]);
-	}
 
-	yield(); /* start all threads before we kthread_stop() */
+		kthread_init_work(&arg[id].work, smoke_crescendo_work);
+		kthread_queue_work(worker[id], &arg[id].work);
+	}
 
 	count = 0;
 	for_each_engine(engine, smoke->gt, id) {
-		int status;
-
-		if (IS_ERR_OR_NULL(tsk[id]))
+		if (IS_ERR_OR_NULL(worker[id]))
 			continue;
 
-		status = kthread_stop(tsk[id]);
-		if (status && !err)
-			err = status;
+		kthread_flush_work(&arg[id].work);
+		if (arg[id].result && !err)
+			err = arg[id].result;
 
 		count += arg[id].count;
 
-		put_task_struct(tsk[id]);
+		kthread_destroy_worker(worker[id]);
 	}
 
 	pr_info("Submitted %lu crescendo:%x requests across %d engines and %d contexts\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/selftest_hangcheck.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/selftest_hangcheck.c
@@ -861,10 +861,13 @@
 }
 
 struct active_engine {
-	struct task_struct *task;
+	struct kthread_worker *worker;
+	struct kthread_work work;
 	struct intel_engine_cs *engine;
 	unsigned long resets;
 	unsigned int flags;
+	bool stop;
+	int result;
 };
 
 #define TEST_ACTIVE	BIT(0)
@@ -895,10 +898,10 @@
 	return err;
 }
 
-static int active_engine(void *data)
+static void active_engine(struct kthread_work *work)
 {
 	I915_RND_STATE(prng);
-	struct active_engine *arg = data;
+	struct active_engine *arg = container_of(work, typeof(*arg), work);
 	struct intel_engine_cs *engine = arg->engine;
 	struct i915_request *rq[8] = {};
 	struct intel_context *ce[ARRAY_SIZE(rq)];
@@ -908,16 +911,17 @@
 	for (count = 0; count < ARRAY_SIZE(ce); count++) {
 		ce[count] = intel_context_create(engine);
 		if (IS_ERR(ce[count])) {
-			err = PTR_ERR(ce[count]);
-			pr_err("[%s] Create context #%ld failed: %d!\n", engine->name, count, err);
+			arg->result = PTR_ERR(ce[count]);
+			pr_err("[%s] Create context #%ld failed: %d!\n",
+			       engine->name, count, arg->result);
 			while (--count)
 				intel_context_put(ce[count]);
-			return err;
+			return;
 		}
 	}
 
 	count = 0;
-	while (!kthread_should_stop()) {
+	while (!READ_ONCE(arg->stop)) {
 		unsigned int idx = count++ & (ARRAY_SIZE(rq) - 1);
 		struct i915_request *old = rq[idx];
 		struct i915_request *new;
@@ -962,7 +966,7 @@
 		intel_context_put(ce[count]);
 	}
 
-	return err;
+	arg->result = err;
 }
 
 static int __igt_reset_engines(struct intel_gt *gt,
@@ -1013,7 +1017,7 @@
 
 		memset(threads, 0, sizeof(threads));
 		for_each_engine(other, gt, tmp) {
-			struct task_struct *tsk;
+			struct kthread_worker *worker;
 
 			threads[tmp].resets =
 				i915_reset_engine_count(global, other);
@@ -1027,19 +1031,21 @@
 			threads[tmp].engine = other;
 			threads[tmp].flags = flags;
 
-			tsk = kthread_run(active_engine, &threads[tmp],
-					  "igt/%s", other->name);
-			if (IS_ERR(tsk)) {
-				err = PTR_ERR(tsk);
-				pr_err("[%s] Thread spawn failed: %d!\n", engine->name, err);
+			worker = kthread_create_worker(0, "igt/%s",
+						       other->name);
+			if (IS_ERR(worker)) {
+				err = PTR_ERR(worker);
+				pr_err("[%s] Worker create failed: %d!\n",
+				       engine->name, err);
 				goto unwind;
 			}
 
-			threads[tmp].task = tsk;
-			get_task_struct(tsk);
-		}
+			threads[tmp].worker = worker;
 
-		yield(); /* start all threads before we begin */
+			kthread_init_work(&threads[tmp].work, active_engine);
+			kthread_queue_work(threads[tmp].worker,
+					   &threads[tmp].work);
+		}
 
 		st_engine_heartbeat_disable_no_pm(engine);
 		set_bit(I915_RESET_ENGINE + id, &gt->reset.flags);
@@ -1187,17 +1193,20 @@
 		for_each_engine(other, gt, tmp) {
 			int ret;
 
-			if (!threads[tmp].task)
+			if (!threads[tmp].worker)
 				continue;
 
-			ret = kthread_stop(threads[tmp].task);
+			WRITE_ONCE(threads[tmp].stop, true);
+			kthread_flush_work(&threads[tmp].work);
+			ret = READ_ONCE(threads[tmp].result);
 			if (ret) {
 				pr_err("kthread for other engine %s failed, err=%d\n",
 				       other->name, ret);
 				if (!err)
 					err = ret;
 			}
-			put_task_struct(threads[tmp].task);
+
+			kthread_destroy_worker(threads[tmp].worker);
 
 			/* GuC based resets are not logged per engine */
 			if (!using_guc) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/selftest_lrc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/selftest_lrc.c
@@ -153,8 +153,8 @@
 			continue;
 
 		hw = shmem_pin_map(engine->default_state);
-		if (IS_ERR(hw)) {
-			err = PTR_ERR(hw);
+		if (!hw) {
+			err = -ENOMEM;
 			break;
 		}
 		hw += LRC_STATE_OFFSET / sizeof(*hw);
@@ -329,8 +329,8 @@
 			continue;
 
 		hw = shmem_pin_map(engine->default_state);
-		if (IS_ERR(hw)) {
-			err = PTR_ERR(hw);
+		if (!hw) {
+			err = -ENOMEM;
 			break;
 		}
 		hw += LRC_STATE_OFFSET / sizeof(*hw);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/uc/intel_guc_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/uc/intel_guc_fw.c
@@ -159,6 +159,6 @@
 	return 0;
 
 out:
-	intel_uc_fw_change_status(&guc->fw, INTEL_UC_FIRMWARE_FAIL);
+	intel_uc_fw_change_status(&guc->fw, INTEL_UC_FIRMWARE_LOAD_FAIL);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/uc/intel_guc_slpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/uc/intel_guc_slpc.c
@@ -133,7 +133,7 @@
 {
 	u32 request[] = {
 		GUC_ACTION_HOST2GUC_PC_SLPC_REQUEST,
-		SLPC_EVENT(SLPC_EVENT_PARAMETER_UNSET, 2),
+		SLPC_EVENT(SLPC_EVENT_PARAMETER_UNSET, 1),
 		id,
 	};
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c
@@ -148,11 +148,12 @@
 #define SCHED_STATE_BLOCKED_SHIFT			4
 #define SCHED_STATE_BLOCKED		BIT(SCHED_STATE_BLOCKED_SHIFT)
 #define SCHED_STATE_BLOCKED_MASK	(0xfff << SCHED_STATE_BLOCKED_SHIFT)
+
 static inline void init_sched_state(struct intel_context *ce)
 {
 	/* Only should be called from guc_lrc_desc_pin() */
 	atomic_set(&ce->guc_sched_state_no_lock, 0);
-	ce->guc_state.sched_state = 0;
+	ce->guc_state.sched_state &= SCHED_STATE_BLOCKED_MASK;
 }
 
 static inline bool
@@ -352,20 +353,29 @@
 	xa_unlock_irqrestore(&guc->context_lookup, flags);
 }
 
+static void decr_outstanding_submission_g2h(struct intel_guc *guc)
+{
+	if (atomic_dec_and_test(&guc->outstanding_submission_g2h))
+		wake_up_all(&guc->ct.wq);
+}
+
 static int guc_submission_send_busy_loop(struct intel_guc *guc,
 					 const u32 *action,
 					 u32 len,
 					 u32 g2h_len_dw,
 					 bool loop)
 {
-	int err;
-
-	err = intel_guc_send_busy_loop(guc, action, len, g2h_len_dw, loop);
+	/*
+	 * We always loop when a send requires a reply (i.e. g2h_len_dw > 0),
+	 * so we don't handle the case where we don't get a reply because we
+	 * aborted the send due to the channel being busy.
+	 */
+	GEM_BUG_ON(g2h_len_dw && !loop);
 
-	if (!err && g2h_len_dw)
+	if (g2h_len_dw)
 		atomic_inc(&guc->outstanding_submission_g2h);
 
-	return err;
+	return intel_guc_send_busy_loop(guc, action, len, g2h_len_dw, loop);
 }
 
 int intel_guc_wait_for_pending_msg(struct intel_guc *guc,
@@ -616,7 +626,7 @@
 		init_sched_state(ce);
 
 		if (pending_enable || destroyed || deregister) {
-			atomic_dec(&guc->outstanding_submission_g2h);
+			decr_outstanding_submission_g2h(guc);
 			if (deregister)
 				guc_signal_context_fence(ce);
 			if (destroyed) {
@@ -635,7 +645,7 @@
 				intel_engine_signal_breadcrumbs(ce->engine);
 			}
 			intel_context_sched_disable_unpin(ce);
-			atomic_dec(&guc->outstanding_submission_g2h);
+			decr_outstanding_submission_g2h(guc);
 			spin_lock_irqsave(&ce->guc_state.lock, flags);
 			guc_blocked_fence_complete(ce);
 			spin_unlock_irqrestore(&ce->guc_state.lock, flags);
@@ -797,15 +807,13 @@
 
 	spin_lock_irqsave(&sched_engine->lock, flags);
 	spin_lock(&ce->guc_active.lock);
-	list_for_each_entry_safe(rq, rn,
-				 &ce->guc_active.requests,
-				 sched.link) {
+	list_for_each_entry_safe_reverse(rq, rn,
+					 &ce->guc_active.requests,
+					 sched.link) {
 		if (i915_request_completed(rq))
 			continue;
 
 		list_del_init(&rq->sched.link);
-		spin_unlock(&ce->guc_active.lock);
-
 		__i915_request_unsubmit(rq);
 
 		/* Push the request back into the queue for later resubmission. */
@@ -816,10 +824,8 @@
 		}
 		GEM_BUG_ON(i915_sched_engine_is_empty(sched_engine));
 
-		list_add_tail(&rq->sched.link, pl);
+		list_add(&rq->sched.link, pl);
 		set_bit(I915_FENCE_FLAG_PQUEUE, &rq->fence.flags);
-
-		spin_lock(&ce->guc_active.lock);
 	}
 	spin_unlock(&ce->guc_active.lock);
 	spin_unlock_irqrestore(&sched_engine->lock, flags);
@@ -828,17 +834,33 @@
 static void __guc_reset_context(struct intel_context *ce, bool stalled)
 {
 	struct i915_request *rq;
+	unsigned long flags;
 	u32 head;
+	bool skip = false;
 
 	intel_context_get(ce);
 
 	/*
-	 * GuC will implicitly mark the context as non-schedulable
-	 * when it sends the reset notification. Make sure our state
-	 * reflects this change. The context will be marked enabled
-	 * on resubmission.
+	 * GuC will implicitly mark the context as non-schedulable when it sends
+	 * the reset notification. Make sure our state reflects this change. The
+	 * context will be marked enabled on resubmission.
+	 *
+	 * XXX: If the context is reset as a result of the request cancellation
+	 * this G2H is received after the schedule disable complete G2H which is
+	 * wrong as this creates a race between the request cancellation code
+	 * re-submitting the context and this G2H handler. This is a bug in the
+	 * GuC but can be worked around in the meantime but converting this to a
+	 * NOP if a pending enable is in flight as this indicates that a request
+	 * cancellation has occurred.
 	 */
-	clr_context_enabled(ce);
+	spin_lock_irqsave(&ce->guc_state.lock, flags);
+	if (likely(!context_pending_enable(ce)))
+		clr_context_enabled(ce);
+	else
+		skip = true;
+	spin_unlock_irqrestore(&ce->guc_state.lock, flags);
+	if (unlikely(skip))
+		goto out_put;
 
 	rq = intel_context_find_active_request(ce);
 	if (!rq) {
@@ -857,6 +879,7 @@
 out_replay:
 	guc_reset_state(ce, head, stalled);
 	__unwind_incomplete_requests(ce);
+out_put:
 	intel_context_put(ce);
 }
 
@@ -1233,8 +1256,7 @@
 }
 
 static int __guc_action_deregister_context(struct intel_guc *guc,
-					   u32 guc_id,
-					   bool loop)
+					   u32 guc_id)
 {
 	u32 action[] = {
 		INTEL_GUC_ACTION_DEREGISTER_CONTEXT,
@@ -1243,16 +1265,16 @@
 
 	return guc_submission_send_busy_loop(guc, action, ARRAY_SIZE(action),
 					     G2H_LEN_DW_DEREGISTER_CONTEXT,
-					     loop);
+					     true);
 }
 
-static int deregister_context(struct intel_context *ce, u32 guc_id, bool loop)
+static int deregister_context(struct intel_context *ce, u32 guc_id)
 {
 	struct intel_guc *guc = ce_to_guc(ce);
 
 	trace_intel_context_deregister(ce);
 
-	return __guc_action_deregister_context(guc, guc_id, loop);
+	return __guc_action_deregister_context(guc, guc_id);
 }
 
 static intel_engine_mask_t adjust_engine_mask(u8 class, intel_engine_mask_t mask)
@@ -1340,26 +1362,23 @@
 	 * registering this context.
 	 */
 	if (context_registered) {
+		bool disabled;
+		unsigned long flags;
+
 		trace_intel_context_steal_guc_id(ce);
-		if (!loop) {
+		GEM_BUG_ON(!loop);
+
+		/* Seal race with Reset */
+		spin_lock_irqsave(&ce->guc_state.lock, flags);
+		disabled = submission_disabled(guc);
+		if (likely(!disabled)) {
 			set_context_wait_for_deregister_to_register(ce);
 			intel_context_get(ce);
-		} else {
-			bool disabled;
-			unsigned long flags;
-
-			/* Seal race with Reset */
-			spin_lock_irqsave(&ce->guc_state.lock, flags);
-			disabled = submission_disabled(guc);
-			if (likely(!disabled)) {
-				set_context_wait_for_deregister_to_register(ce);
-				intel_context_get(ce);
-			}
-			spin_unlock_irqrestore(&ce->guc_state.lock, flags);
-			if (unlikely(disabled)) {
-				reset_lrc_desc(guc, desc_idx);
-				return 0;	/* Will get registered later */
-			}
+		}
+		spin_unlock_irqrestore(&ce->guc_state.lock, flags);
+		if (unlikely(disabled)) {
+			reset_lrc_desc(guc, desc_idx);
+			return 0;	/* Will get registered later */
 		}
 
 		/*
@@ -1367,13 +1386,9 @@
 		 * context whose guc_id was stolen.
 		 */
 		with_intel_runtime_pm(runtime_pm, wakeref)
-			ret = deregister_context(ce, ce->guc_id, loop);
-		if (unlikely(ret == -EBUSY)) {
-			clr_context_wait_for_deregister_to_register(ce);
-			intel_context_put(ce);
-		} else if (unlikely(ret == -ENODEV)) {
+			ret = deregister_context(ce, ce->guc_id);
+		if (unlikely(ret == -ENODEV))
 			ret = 0;	/* Will get registered later */
-		}
 	} else {
 		with_intel_runtime_pm(runtime_pm, wakeref)
 			ret = register_context(ce, loop);
@@ -1548,6 +1563,23 @@
 	return &ce->guc_blocked;
 }
 
+#define SCHED_STATE_MULTI_BLOCKED_MASK \
+	(SCHED_STATE_BLOCKED_MASK & ~SCHED_STATE_BLOCKED)
+#define SCHED_STATE_NO_UNBLOCK \
+	(SCHED_STATE_MULTI_BLOCKED_MASK | \
+	 SCHED_STATE_PENDING_DISABLE | \
+	 SCHED_STATE_BANNED)
+
+static bool context_cant_unblock(struct intel_context *ce)
+{
+	lockdep_assert_held(&ce->guc_state.lock);
+
+	return (ce->guc_state.sched_state & SCHED_STATE_NO_UNBLOCK) ||
+		context_guc_id_invalid(ce) ||
+		!lrc_desc_registered(ce_to_guc(ce), ce->guc_id) ||
+		!intel_context_is_pinned(ce);
+}
+
 static void guc_context_unblock(struct intel_context *ce)
 {
 	struct intel_guc *guc = ce_to_guc(ce);
@@ -1562,9 +1594,7 @@
 	spin_lock_irqsave(&ce->guc_state.lock, flags);
 
 	if (unlikely(submission_disabled(guc) ||
-		     !intel_context_is_pinned(ce) ||
-		     context_pending_disable(ce) ||
-		     context_blocked(ce) > 1)) {
+		     context_cant_unblock(ce))) {
 		enable = false;
 	} else {
 		enable = true;
@@ -1601,6 +1631,13 @@
 			guc_reset_state(ce, intel_ring_wrap(ce->ring, rq->head),
 					true);
 		}
+
+		/*
+		 * XXX: Racey if context is reset, see comment in
+		 * __guc_reset_context().
+		 */
+		flush_work(&ce_to_guc(ce)->ct.requests.worker);
+
 		guc_context_unblock(ce);
 	}
 }
@@ -1730,7 +1767,7 @@
 	GEM_BUG_ON(context_enabled(ce));
 
 	clr_context_registered(ce);
-	deregister_context(ce, ce->guc_id, true);
+	deregister_context(ce, ce->guc_id);
 }
 
 static void __guc_context_destroy(struct intel_context *ce)
@@ -2310,6 +2347,8 @@
 
 	/* And scrub the dirty cachelines for the HWSP */
 	clflush_cache_range(engine->status_page.addr, PAGE_SIZE);
+
+	intel_engine_reset_pinned_contexts(engine);
 }
 
 static void setup_hwsp(struct intel_engine_cs *engine)
@@ -2385,9 +2424,13 @@
 	 * and even it did this code would be run again.
 	 */
 
-	for_each_engine(engine, gt, id)
-		if (engine->kernel_context)
-			guc_kernel_context_pin(guc, engine->kernel_context);
+	for_each_engine(engine, gt, id) {
+		struct intel_context *ce;
+
+		list_for_each_entry(ce, &engine->pinned_contexts_list,
+				    pinned_contexts_link)
+			guc_kernel_context_pin(guc, ce);
+	}
 }
 
 static void guc_release(struct intel_engine_cs *engine)
@@ -2583,12 +2626,6 @@
 	return ce;
 }
 
-static void decr_outstanding_submission_g2h(struct intel_guc *guc)
-{
-	if (atomic_dec_and_test(&guc->outstanding_submission_g2h))
-		wake_up_all(&guc->ct.wq);
-}
-
 int intel_guc_deregister_done_process_msg(struct intel_guc *guc,
 					  const u32 *msg,
 					  u32 len)
@@ -2721,7 +2758,12 @@
 {
 	trace_intel_context_reset(ce);
 
-	if (likely(!intel_context_is_banned(ce))) {
+	/*
+	 * XXX: Racey if request cancellation has occurred, see comment in
+	 * __guc_reset_context().
+	 */
+	if (likely(!intel_context_is_banned(ce) &&
+		   !context_blocked(ce))) {
 		capture_error_state(guc, ce);
 		guc_context_replay(ce);
 	}
@@ -2803,6 +2845,8 @@
 		return;
 
 	xa_for_each(&guc->context_lookup, index, ce) {
+		bool found;
+
 		if (!intel_context_is_pinned(ce))
 			continue;
 
@@ -2814,10 +2858,18 @@
 				continue;
 		}
 
+		found = false;
+		spin_lock(&ce->guc_state.lock);
 		list_for_each_entry(rq, &ce->guc_active.requests, sched.link) {
 			if (i915_test_request_state(rq) != I915_REQUEST_ACTIVE)
 				continue;
 
+			found = true;
+			break;
+		}
+		spin_unlock(&ce->guc_state.lock);
+
+		if (found) {
 			intel_engine_set_hung_context(engine, ce);
 
 			/* Can only cope with one hang at a time... */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/uc/intel_huc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/uc/intel_huc.c
@@ -191,7 +191,7 @@
 
 fail:
 	i915_probe_error(gt->i915, "HuC: Authentication failed %d\n", ret);
-	intel_uc_fw_change_status(&huc->fw, INTEL_UC_FIRMWARE_FAIL);
+	intel_uc_fw_change_status(&huc->fw, INTEL_UC_FIRMWARE_LOAD_FAIL);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/uc/intel_uc_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/uc/intel_uc_fw.c
@@ -526,7 +526,7 @@
 	i915_probe_error(gt->i915, "Failed to load %s firmware %s (%d)\n",
 			 intel_uc_fw_type_repr(uc_fw->type), uc_fw->path,
 			 err);
-	intel_uc_fw_change_status(uc_fw, INTEL_UC_FIRMWARE_FAIL);
+	intel_uc_fw_change_status(uc_fw, INTEL_UC_FIRMWARE_LOAD_FAIL);
 	return err;
 }
 
@@ -544,7 +544,7 @@
 	if (err) {
 		DRM_DEBUG_DRIVER("%s fw pin-pages err=%d\n",
 				 intel_uc_fw_type_repr(uc_fw->type), err);
-		intel_uc_fw_change_status(uc_fw, INTEL_UC_FIRMWARE_FAIL);
+		intel_uc_fw_change_status(uc_fw, INTEL_UC_FIRMWARE_INIT_FAIL);
 	}
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gt/uc/intel_uc_fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gt/uc/intel_uc_fw.h
@@ -31,11 +31,12 @@
  * |            |    MISSING <--/    |    \--> ERROR                |
  * |   fetch    |                    V                              |
  * |            |                 AVAILABLE                         |
- * +------------+-                   |                             -+
+ * +------------+-                   |   \                         -+
+ * |            |                    |    \--> INIT FAIL            |
  * |   init     |                    V                              |
  * |            |        /------> LOADABLE <----<-----------\       |
  * +------------+-       \         /    \        \           \     -+
- * |            |         FAIL <--<      \--> TRANSFERRED     \     |
+ * |            |    LOAD FAIL <--<      \--> TRANSFERRED     \     |
  * |   upload   |                  \           /   \          /     |
  * |            |                   \---------/     \--> RUNNING    |
  * +------------+---------------------------------------------------+
@@ -49,8 +50,9 @@
 	INTEL_UC_FIRMWARE_MISSING, /* blob not found on the system */
 	INTEL_UC_FIRMWARE_ERROR, /* invalid format or version */
 	INTEL_UC_FIRMWARE_AVAILABLE, /* blob found and copied in mem */
+	INTEL_UC_FIRMWARE_INIT_FAIL, /* failed to prepare fw objects for load */
 	INTEL_UC_FIRMWARE_LOADABLE, /* all fw-required objects are ready */
-	INTEL_UC_FIRMWARE_FAIL, /* failed to xfer or init/auth the fw */
+	INTEL_UC_FIRMWARE_LOAD_FAIL, /* failed to xfer or init/auth the fw */
 	INTEL_UC_FIRMWARE_TRANSFERRED, /* dma xfer done */
 	INTEL_UC_FIRMWARE_RUNNING /* init/auth done */
 };
@@ -121,10 +123,12 @@
 		return "ERROR";
 	case INTEL_UC_FIRMWARE_AVAILABLE:
 		return "AVAILABLE";
+	case INTEL_UC_FIRMWARE_INIT_FAIL:
+		return "INIT FAIL";
 	case INTEL_UC_FIRMWARE_LOADABLE:
 		return "LOADABLE";
-	case INTEL_UC_FIRMWARE_FAIL:
-		return "FAIL";
+	case INTEL_UC_FIRMWARE_LOAD_FAIL:
+		return "LOAD FAIL";
 	case INTEL_UC_FIRMWARE_TRANSFERRED:
 		return "TRANSFERRED";
 	case INTEL_UC_FIRMWARE_RUNNING:
@@ -146,7 +150,8 @@
 		return -ENOENT;
 	case INTEL_UC_FIRMWARE_ERROR:
 		return -ENOEXEC;
-	case INTEL_UC_FIRMWARE_FAIL:
+	case INTEL_UC_FIRMWARE_INIT_FAIL:
+	case INTEL_UC_FIRMWARE_LOAD_FAIL:
 		return -EIO;
 	case INTEL_UC_FIRMWARE_SELECTED:
 		return -ESTALE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gvt/cmd_parser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gvt/cmd_parser.c
@@ -3115,9 +3115,9 @@
 			continue;
 
 		vaddr = shmem_pin_map(engine->default_state);
-		if (IS_ERR(vaddr)) {
-			gvt_err("failed to map %s->default state, err:%zd\n",
-				engine->name, PTR_ERR(vaddr));
+		if (!vaddr) {
+			gvt_err("failed to map %s->default state\n",
+				engine->name);
 			return;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gvt/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gvt/debugfs.c
@@ -175,8 +175,13 @@
  */
 void intel_gvt_debugfs_remove_vgpu(struct intel_vgpu *vgpu)
 {
-	debugfs_remove_recursive(vgpu->debugfs);
-	vgpu->debugfs = NULL;
+	struct intel_gvt *gvt = vgpu->gvt;
+	struct drm_minor *minor = gvt->gt->i915->drm.primary;
+
+	if (minor->debugfs_root && gvt->debugfs_root) {
+		debugfs_remove_recursive(vgpu->debugfs);
+		vgpu->debugfs = NULL;
+	}
 }
 
 /**
@@ -199,6 +204,10 @@
  */
 void intel_gvt_debugfs_clean(struct intel_gvt *gvt)
 {
-	debugfs_remove_recursive(gvt->debugfs_root);
-	gvt->debugfs_root = NULL;
+	struct drm_minor *minor = gvt->gt->i915->drm.primary;
+
+	if (minor->debugfs_root) {
+		debugfs_remove_recursive(gvt->debugfs_root);
+		gvt->debugfs_root = NULL;
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gvt/gtt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gvt/gtt.c
@@ -1195,10 +1195,8 @@
 	for_each_shadow_entry(sub_spt, &sub_se, sub_index) {
 		ret = intel_gvt_hypervisor_dma_map_guest_page(vgpu,
 				start_gfn + sub_index, PAGE_SIZE, &dma_addr);
-		if (ret) {
-			ppgtt_invalidate_spt(spt);
-			return ret;
-		}
+		if (ret)
+			goto err;
 		sub_se.val64 = se->val64;
 
 		/* Copy the PAT field from PDE. */
@@ -1217,6 +1215,17 @@
 	ops->set_pfn(se, sub_spt->shadow_page.mfn);
 	ppgtt_set_shadow_entry(spt, se, index);
 	return 0;
+err:
+	/* Cancel the existing addess mappings of DMA addr. */
+	for_each_present_shadow_entry(sub_spt, &sub_se, sub_index) {
+		gvt_vdbg_mm("invalidate 4K entry\n");
+		ppgtt_invalidate_pte(sub_spt, &sub_se);
+	}
+	/* Release the new allocated spt. */
+	trace_spt_change(sub_spt->vgpu->id, "release", sub_spt,
+		sub_spt->guest_page.gfn, sub_spt->shadow_page.type);
+	ppgtt_free_spt(sub_spt);
+	return ret;
 }
 
 static int split_64KB_gtt_entry(struct intel_vgpu *vgpu,
@@ -2856,24 +2865,6 @@
 }
 
 /**
- * intel_vgpu_reset_gtt - reset the all GTT related status
- * @vgpu: a vGPU
- *
- * This function is called from vfio core to reset reset all
- * GTT related status, including GGTT, PPGTT, scratch page.
- *
- */
-void intel_vgpu_reset_gtt(struct intel_vgpu *vgpu)
-{
-	/* Shadow pages are only created when there is no page
-	 * table tracking data, so remove page tracking data after
-	 * removing the shadow pages.
-	 */
-	intel_vgpu_destroy_all_ppgtt_mm(vgpu);
-	intel_vgpu_reset_ggtt(vgpu, true);
-}
-
-/**
  * intel_gvt_restore_ggtt - restore all vGPU's ggtt entries
  * @gvt: intel gvt device
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gvt/gtt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gvt/gtt.h
@@ -224,7 +224,6 @@
 void intel_vgpu_invalidate_ppgtt(struct intel_vgpu *vgpu);
 
 int intel_gvt_init_gtt(struct intel_gvt *gvt);
-void intel_vgpu_reset_gtt(struct intel_vgpu *vgpu);
 void intel_gvt_clean_gtt(struct intel_gvt *gvt);
 
 struct intel_vgpu_mm *intel_gvt_find_ppgtt_mm(struct intel_vgpu *vgpu,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gvt/handlers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gvt/handlers.c
@@ -909,7 +909,7 @@
 	else if (FDI_RX_IMR_TO_PIPE(offset) != INVALID_INDEX)
 		index = FDI_RX_IMR_TO_PIPE(offset);
 	else {
-		gvt_vgpu_err("Unsupport registers %x\n", offset);
+		gvt_vgpu_err("Unsupported registers %x\n", offset);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/gvt/scheduler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/gvt/scheduler.c
@@ -694,6 +694,7 @@
 
 	if (workload->shadow_mm->type != INTEL_GVT_MM_PPGTT ||
 	    !workload->shadow_mm->ppgtt_mm.shadowed) {
+		intel_vgpu_unpin_mm(workload->shadow_mm);
 		gvt_vgpu_err("workload shadow ppgtt isn't ready\n");
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_active.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_active.c
@@ -92,8 +92,7 @@
 static void debug_active_activate(struct i915_active *ref)
 {
 	lockdep_assert_held(&ref->tree_lock);
-	if (!atomic_read(&ref->count)) /* before the first inc */
-		debug_object_activate(ref, &active_debug_desc);
+	debug_object_activate(ref, &active_debug_desc);
 }
 
 static void debug_active_deactivate(struct i915_active *ref)
@@ -422,8 +421,7 @@
 	 * we can use it to substitute for the pending idle-barrer
 	 * request that we want to emit on the kernel_context.
 	 */
-	__active_del_barrier(ref, node_from_active(active));
-	return true;
+	return __active_del_barrier(ref, node_from_active(active));
 }
 
 int i915_active_ref(struct i915_active *ref, u64 idx, struct dma_fence *fence)
@@ -436,18 +434,24 @@
 	if (err)
 		return err;
 
-	active = active_instance(ref, idx);
-	if (!active) {
-		err = -ENOMEM;
-		goto out;
-	}
+	do {
+		active = active_instance(ref, idx);
+		if (!active) {
+			err = -ENOMEM;
+			goto out;
+		}
 
-	if (replace_barrier(ref, active)) {
-		RCU_INIT_POINTER(active->fence, NULL);
-		atomic_dec(&ref->count);
-	}
-	if (!__i915_active_fence_set(active, fence))
+		if (replace_barrier(ref, active)) {
+			RCU_INIT_POINTER(active->fence, NULL);
+			atomic_dec(&ref->count);
+		}
+	} while (unlikely(is_barrier(active)));
+
+	fence = __i915_active_fence_set(active, fence);
+	if (!fence)
 		__i915_active_acquire(ref);
+	else
+		dma_fence_put(fence);
 
 out:
 	i915_active_release(ref);
@@ -466,13 +470,9 @@
 		return NULL;
 	}
 
-	rcu_read_lock();
 	prev = __i915_active_fence_set(active, fence);
-	if (prev)
-		prev = dma_fence_get_rcu(prev);
-	else
+	if (!prev)
 		__i915_active_acquire(ref);
-	rcu_read_unlock();
 
 	return prev;
 }
@@ -1039,10 +1039,11 @@
  *
  * Records the new @fence as the last active fence along its timeline in
  * this active tracker, moving the tracking callbacks from the previous
- * fence onto this one. Returns the previous fence (if not already completed),
- * which the caller must ensure is executed before the new fence. To ensure
- * that the order of fences within the timeline of the i915_active_fence is
- * understood, it should be locked by the caller.
+ * fence onto this one. Gets and returns a reference to the previous fence
+ * (if not already completed), which the caller must put after making sure
+ * that it is executed before the new fence. To ensure that the order of
+ * fences within the timeline of the i915_active_fence is understood, it
+ * should be locked by the caller.
  */
 struct dma_fence *
 __i915_active_fence_set(struct i915_active_fence *active,
@@ -1051,7 +1052,23 @@
 	struct dma_fence *prev;
 	unsigned long flags;
 
-	if (fence == rcu_access_pointer(active->fence))
+	/*
+	 * In case of fences embedded in i915_requests, their memory is
+	 * SLAB_FAILSAFE_BY_RCU, then it can be reused right after release
+	 * by new requests.  Then, there is a risk of passing back a pointer
+	 * to a new, completely unrelated fence that reuses the same memory
+	 * while tracked under a different active tracker.  Combined with i915
+	 * perf open/close operations that build await dependencies between
+	 * engine kernel context requests and user requests from different
+	 * timelines, this can lead to dependency loops and infinite waits.
+	 *
+	 * As a countermeasure, we try to get a reference to the active->fence
+	 * first, so if we succeed and pass it back to our user then it is not
+	 * released and potentially reused by an unrelated request before the
+	 * user has a chance to set up an await dependency on it.
+	 */
+	prev = i915_active_fence_get(active);
+	if (fence == prev)
 		return fence;
 
 	GEM_BUG_ON(test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags));
@@ -1060,27 +1077,56 @@
 	 * Consider that we have two threads arriving (A and B), with
 	 * C already resident as the active->fence.
 	 *
-	 * A does the xchg first, and so it sees C or NULL depending
-	 * on the timing of the interrupt handler. If it is NULL, the
-	 * previous fence must have been signaled and we know that
-	 * we are first on the timeline. If it is still present,
-	 * we acquire the lock on that fence and serialise with the interrupt
-	 * handler, in the process removing it from any future interrupt
-	 * callback. A will then wait on C before executing (if present).
-	 *
-	 * As B is second, it sees A as the previous fence and so waits for
-	 * it to complete its transition and takes over the occupancy for
-	 * itself -- remembering that it needs to wait on A before executing.
+	 * Both A and B have got a reference to C or NULL, depending on the
+	 * timing of the interrupt handler.  Let's assume that if A has got C
+	 * then it has locked C first (before B).
 	 *
 	 * Note the strong ordering of the timeline also provides consistent
 	 * nesting rules for the fence->lock; the inner lock is always the
 	 * older lock.
 	 */
 	spin_lock_irqsave(fence->lock, flags);
-	prev = xchg(__active_fence_slot(active), fence);
-	if (prev) {
-		GEM_BUG_ON(prev == fence);
+	if (prev)
 		spin_lock_nested(prev->lock, SINGLE_DEPTH_NESTING);
+
+	/*
+	 * A does the cmpxchg first, and so it sees C or NULL, as before, or
+	 * something else, depending on the timing of other threads and/or
+	 * interrupt handler.  If not the same as before then A unlocks C if
+	 * applicable and retries, starting from an attempt to get a new
+	 * active->fence.  Meanwhile, B follows the same path as A.
+	 * Once A succeeds with cmpxch, B fails again, retires, gets A from
+	 * active->fence, locks it as soon as A completes, and possibly
+	 * succeeds with cmpxchg.
+	 */
+	while (cmpxchg(__active_fence_slot(active), prev, fence) != prev) {
+		if (prev) {
+			spin_unlock(prev->lock);
+			dma_fence_put(prev);
+		}
+		spin_unlock_irqrestore(fence->lock, flags);
+
+		prev = i915_active_fence_get(active);
+		GEM_BUG_ON(prev == fence);
+
+		spin_lock_irqsave(fence->lock, flags);
+		if (prev)
+			spin_lock_nested(prev->lock, SINGLE_DEPTH_NESTING);
+	}
+
+	/*
+	 * If prev is NULL then the previous fence must have been signaled
+	 * and we know that we are first on the timeline.  If it is still
+	 * present then, having the lock on that fence already acquired, we
+	 * serialise with the interrupt handler, in the process of removing it
+	 * from any future interrupt callback.  A will then wait on C before
+	 * executing (if present).
+	 *
+	 * As B is second, it sees A as the previous fence and so waits for
+	 * it to complete its transition and takes over the occupancy for
+	 * itself -- remembering that it needs to wait on A before executing.
+	 */
+	if (prev) {
 		__list_del_entry(&active->cb.node);
 		spin_unlock(prev->lock); /* serialise with prev->cb_list */
 	}
@@ -1097,11 +1143,7 @@
 	int err = 0;
 
 	/* Must maintain timeline ordering wrt previous active requests */
-	rcu_read_lock();
 	fence = __i915_active_fence_set(active, &rq->fence);
-	if (fence) /* but the previous fence may not belong to that timeline! */
-		fence = dma_fence_get_rcu(fence);
-	rcu_read_unlock();
 	if (fence) {
 		err = i915_request_await_dma_fence(rq, fence);
 		dma_fence_put(fence);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_drv.c
@@ -986,12 +986,9 @@
  */
 static void i915_driver_lastclose(struct drm_device *dev)
 {
-	struct drm_i915_private *i915 = to_i915(dev);
-
 	intel_fbdev_restore_mode(dev);
 
-	if (HAS_DISPLAY(i915))
-		vga_switcheroo_process_delayed_switch();
+	vga_switcheroo_process_delayed_switch();
 }
 
 static void i915_driver_postclose(struct drm_device *dev, struct drm_file *file)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_drv.h
@@ -524,6 +524,7 @@
 #define QUIRK_INCREASE_T12_DELAY (1<<6)
 #define QUIRK_INCREASE_DDI_DISABLED_TIME (1<<7)
 #define QUIRK_NO_PPS_BACKLIGHT_POWER_HOOK (1<<8)
+#define QUIRK_FORCE_DISABLE_FASTBOOT (1<<9)
 
 struct intel_fbdev;
 struct intel_fbc_work;
@@ -886,8 +887,6 @@
 	 */
 	u32 gpio_mmio_base;
 
-	u32 hsw_psr_mmio_adjust;
-
 	/* MMIO base address for MIPI regs */
 	u32 mipi_mmio_base;
 
@@ -1905,6 +1904,10 @@
 struct drm_i915_gem_object *
 i915_gem_object_create_internal(struct drm_i915_private *dev_priv,
 				phys_addr_t size);
+struct drm_i915_gem_object *
+__i915_gem_object_create_internal(struct drm_i915_private *dev_priv,
+				  const struct drm_i915_gem_object_ops *ops,
+				  phys_addr_t size);
 
 /* i915_gem_tiling.c */
 static inline bool i915_gem_object_needs_bit17_swizzle(struct drm_i915_gem_object *obj)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_irq.c
@@ -2093,22 +2093,6 @@
 	if (de_iir & DE_ERR_INT_IVB)
 		ivb_err_int_handler(dev_priv);
 
-	if (de_iir & DE_EDP_PSR_INT_HSW) {
-		struct intel_encoder *encoder;
-
-		for_each_intel_encoder_with_psr(&dev_priv->drm, encoder) {
-			struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
-
-			u32 psr_iir = intel_uncore_read(&dev_priv->uncore,
-							EDP_PSR_IIR);
-
-			intel_psr_irq_handler(intel_dp, psr_iir);
-			intel_uncore_write(&dev_priv->uncore,
-					   EDP_PSR_IIR, psr_iir);
-			break;
-		}
-	}
-
 	if (de_iir & DE_AUX_CHANNEL_A_IVB)
 		dp_aux_irq_handler(dev_priv);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_pci.c
@@ -401,7 +401,8 @@
 	.has_coherent_ggtt = true, \
 	.has_llc = 1, \
 	.has_rc6 = 1, \
-	.has_rc6p = 1, \
+	/* snb does support rc6p, but enabling it causes various issues */ \
+	.has_rc6p = 0, \
 	.has_rps = true, \
 	.dma_mask_size = 40, \
 	.ppgtt_type = INTEL_PPGTT_ALIASING, \
@@ -537,8 +538,6 @@
 		BIT(TRANSCODER_C) | BIT(TRANSCODER_EDP), \
 	.display.has_ddi = 1, \
 	.display.has_fpga_dbg = 1, \
-	.display.has_psr = 1, \
-	.display.has_psr_hw_tracking = 1, \
 	.display.has_dp_mst = 1, \
 	.has_rc6p = 0 /* RC6p removed-by HSW */, \
 	HSW_PIPE_OFFSETS, \
@@ -642,6 +641,8 @@
 	.has_gt_uc = 1, \
 	.display.has_hdcp = 1, \
 	.display.has_ipc = 1, \
+	.display.has_psr = 1, \
+	.display.has_psr_hw_tracking = 1, \
 	.dbuf.size = 896 - 4, /* 4 blocks for bypass path allocation */ \
 	.dbuf.slice_mask = BIT(DBUF_S1)
 
@@ -865,7 +866,7 @@
 	}, \
 	TGL_CURSOR_OFFSETS, \
 	.has_global_mocs = 1, \
-	.display.has_dsb = 1
+	.display.has_dsb = 0 /* FIXME: LUT load is broken with DSB */
 
 static const struct intel_device_info tgl_info = {
 	GEN12_FEATURES,
@@ -912,7 +913,6 @@
 	GEN12_FEATURES,
 	PLATFORM(INTEL_ALDERLAKE_S),
 	.pipe_mask = BIT(PIPE_A) | BIT(PIPE_B) | BIT(PIPE_C) | BIT(PIPE_D),
-	.require_force_probe = 1,
 	.display.has_hti = 1,
 	.display.has_psr_hw_tracking = 0,
 	.platform_engine_mask =
@@ -930,7 +930,10 @@
 
 #define XE_LPD_FEATURES \
 	.abox_mask = GENMASK(1, 0),						\
-	.color = { .degamma_lut_size = 0, .gamma_lut_size = 0 },		\
+	.color = { .degamma_lut_size = 128, .gamma_lut_size = 1024,		\
+		   .degamma_lut_tests = DRM_COLOR_LUT_NON_DECREASING |		\
+					DRM_COLOR_LUT_EQUAL_CHANNELS,		\
+	},									\
 	.cpu_transcoder_mask = BIT(TRANSCODER_A) | BIT(TRANSCODER_B) |		\
 		BIT(TRANSCODER_C) | BIT(TRANSCODER_D),				\
 	.dbuf.size = 4096,							\
@@ -967,7 +970,6 @@
 	GEN12_FEATURES,
 	XE_LPD_FEATURES,
 	PLATFORM(INTEL_ALDERLAKE_P),
-	.require_force_probe = 1,
 	.display.has_cdclk_crawl = 1,
 	.display.has_modular_fia = 1,
 	.display.has_psr_hw_tracking = 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_perf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_perf.c
@@ -879,8 +879,9 @@
 		if (ret)
 			return ret;
 
-		DRM_DEBUG("OA buffer overflow (exponent = %d): force restart\n",
-			  stream->period_exponent);
+		drm_dbg(&stream->perf->i915->drm,
+			"OA buffer overflow (exponent = %d): force restart\n",
+			stream->period_exponent);
 
 		stream->perf->ops.oa_disable(stream);
 		stream->perf->ops.oa_enable(stream);
@@ -1102,8 +1103,9 @@
 		if (ret)
 			return ret;
 
-		DRM_DEBUG("OA buffer overflow (exponent = %d): force restart\n",
-			  stream->period_exponent);
+		drm_dbg(&stream->perf->i915->drm,
+			"OA buffer overflow (exponent = %d): force restart\n",
+			stream->period_exponent);
 
 		stream->perf->ops.oa_disable(stream);
 		stream->perf->ops.oa_enable(stream);
@@ -2857,7 +2859,8 @@
 	int ret;
 
 	if (!props->engine) {
-		DRM_DEBUG("OA engine not specified\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"OA engine not specified\n");
 		return -EINVAL;
 	}
 
@@ -2867,18 +2870,21 @@
 	 * IDs
 	 */
 	if (!perf->metrics_kobj) {
-		DRM_DEBUG("OA metrics weren't advertised via sysfs\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"OA metrics weren't advertised via sysfs\n");
 		return -EINVAL;
 	}
 
 	if (!(props->sample_flags & SAMPLE_OA_REPORT) &&
 	    (GRAPHICS_VER(perf->i915) < 12 || !stream->ctx)) {
-		DRM_DEBUG("Only OA report sampling supported\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"Only OA report sampling supported\n");
 		return -EINVAL;
 	}
 
 	if (!perf->ops.enable_metric_set) {
-		DRM_DEBUG("OA unit not supported\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"OA unit not supported\n");
 		return -ENODEV;
 	}
 
@@ -2888,12 +2894,14 @@
 	 * we currently only allow exclusive access
 	 */
 	if (perf->exclusive_stream) {
-		DRM_DEBUG("OA unit already in use\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"OA unit already in use\n");
 		return -EBUSY;
 	}
 
 	if (!props->oa_format) {
-		DRM_DEBUG("OA report format not specified\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"OA report format not specified\n");
 		return -EINVAL;
 	}
 
@@ -2923,20 +2931,23 @@
 	if (stream->ctx) {
 		ret = oa_get_render_ctx_id(stream);
 		if (ret) {
-			DRM_DEBUG("Invalid context id to filter with\n");
+			drm_dbg(&stream->perf->i915->drm,
+				"Invalid context id to filter with\n");
 			return ret;
 		}
 	}
 
 	ret = alloc_noa_wait(stream);
 	if (ret) {
-		DRM_DEBUG("Unable to allocate NOA wait batch buffer\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"Unable to allocate NOA wait batch buffer\n");
 		goto err_noa_wait_alloc;
 	}
 
 	stream->oa_config = i915_perf_get_oa_config(perf, props->metrics_set);
 	if (!stream->oa_config) {
-		DRM_DEBUG("Invalid OA config id=%i\n", props->metrics_set);
+		drm_dbg(&stream->perf->i915->drm,
+			"Invalid OA config id=%i\n", props->metrics_set);
 		ret = -EINVAL;
 		goto err_config;
 	}
@@ -2967,11 +2978,13 @@
 
 	ret = i915_perf_stream_enable_sync(stream);
 	if (ret) {
-		DRM_DEBUG("Unable to enable metric set\n");
+		drm_dbg(&stream->perf->i915->drm,
+			"Unable to enable metric set\n");
 		goto err_enable;
 	}
 
-	DRM_DEBUG("opening stream oa config uuid=%s\n",
+	drm_dbg(&stream->perf->i915->drm,
+		"opening stream oa config uuid=%s\n",
 		  stream->oa_config->uuid);
 
 	hrtimer_init(&stream->poll_check_timer,
@@ -3423,7 +3436,8 @@
 
 		specific_ctx = i915_gem_context_lookup(file_priv, ctx_handle);
 		if (IS_ERR(specific_ctx)) {
-			DRM_DEBUG("Failed to look up context with ID %u for opening perf stream\n",
+			drm_dbg(&perf->i915->drm,
+				"Failed to look up context with ID %u for opening perf stream\n",
 				  ctx_handle);
 			ret = PTR_ERR(specific_ctx);
 			goto err;
@@ -3457,7 +3471,8 @@
 
 	if (props->hold_preemption) {
 		if (!props->single_context) {
-			DRM_DEBUG("preemption disable with no context\n");
+			drm_dbg(&perf->i915->drm,
+				"preemption disable with no context\n");
 			ret = -EINVAL;
 			goto err;
 		}
@@ -3479,7 +3494,8 @@
 	 */
 	if (privileged_op &&
 	    i915_perf_stream_paranoid && !perfmon_capable()) {
-		DRM_DEBUG("Insufficient privileges to open i915 perf stream\n");
+		drm_dbg(&perf->i915->drm,
+			"Insufficient privileges to open i915 perf stream\n");
 		ret = -EACCES;
 		goto err_ctx;
 	}
@@ -3586,7 +3602,8 @@
 	props->poll_oa_period = DEFAULT_POLL_PERIOD_NS;
 
 	if (!n_props) {
-		DRM_DEBUG("No i915 perf properties given\n");
+		drm_dbg(&perf->i915->drm,
+			"No i915 perf properties given\n");
 		return -EINVAL;
 	}
 
@@ -3595,7 +3612,8 @@
 						 I915_ENGINE_CLASS_RENDER,
 						 0);
 	if (!props->engine) {
-		DRM_DEBUG("No RENDER-capable engines\n");
+		drm_dbg(&perf->i915->drm,
+			"No RENDER-capable engines\n");
 		return -EINVAL;
 	}
 
@@ -3606,7 +3624,8 @@
 	 * from userspace.
 	 */
 	if (n_props >= DRM_I915_PERF_PROP_MAX) {
-		DRM_DEBUG("More i915 perf properties specified than exist\n");
+		drm_dbg(&perf->i915->drm,
+			"More i915 perf properties specified than exist\n");
 		return -EINVAL;
 	}
 
@@ -3623,7 +3642,8 @@
 			return ret;
 
 		if (id == 0 || id >= DRM_I915_PERF_PROP_MAX) {
-			DRM_DEBUG("Unknown i915 perf property ID\n");
+			drm_dbg(&perf->i915->drm,
+				"Unknown i915 perf property ID\n");
 			return -EINVAL;
 		}
 
@@ -3638,19 +3658,22 @@
 			break;
 		case DRM_I915_PERF_PROP_OA_METRICS_SET:
 			if (value == 0) {
-				DRM_DEBUG("Unknown OA metric set ID\n");
+				drm_dbg(&perf->i915->drm,
+					"Unknown OA metric set ID\n");
 				return -EINVAL;
 			}
 			props->metrics_set = value;
 			break;
 		case DRM_I915_PERF_PROP_OA_FORMAT:
 			if (value == 0 || value >= I915_OA_FORMAT_MAX) {
-				DRM_DEBUG("Out-of-range OA report format %llu\n",
+				drm_dbg(&perf->i915->drm,
+					"Out-of-range OA report format %llu\n",
 					  value);
 				return -EINVAL;
 			}
 			if (!oa_format_valid(perf, value)) {
-				DRM_DEBUG("Unsupported OA report format %llu\n",
+				drm_dbg(&perf->i915->drm,
+					"Unsupported OA report format %llu\n",
 					  value);
 				return -EINVAL;
 			}
@@ -3658,7 +3681,8 @@
 			break;
 		case DRM_I915_PERF_PROP_OA_EXPONENT:
 			if (value > OA_EXPONENT_MAX) {
-				DRM_DEBUG("OA timer exponent too high (> %u)\n",
+				drm_dbg(&perf->i915->drm,
+					"OA timer exponent too high (> %u)\n",
 					 OA_EXPONENT_MAX);
 				return -EINVAL;
 			}
@@ -3686,7 +3710,8 @@
 				oa_freq_hz = 0;
 
 			if (oa_freq_hz > i915_oa_max_sample_rate && !perfmon_capable()) {
-				DRM_DEBUG("OA exponent would exceed the max sampling frequency (sysctl dev.i915.oa_max_sample_rate) %uHz without CAP_PERFMON or CAP_SYS_ADMIN privileges\n",
+				drm_dbg(&perf->i915->drm,
+					"OA exponent would exceed the max sampling frequency (sysctl dev.i915.oa_max_sample_rate) %uHz without CAP_PERFMON or CAP_SYS_ADMIN privileges\n",
 					  i915_oa_max_sample_rate);
 				return -EACCES;
 			}
@@ -3703,13 +3728,15 @@
 			if (copy_from_user(&user_sseu,
 					   u64_to_user_ptr(value),
 					   sizeof(user_sseu))) {
-				DRM_DEBUG("Unable to copy global sseu parameter\n");
+				drm_dbg(&perf->i915->drm,
+					"Unable to copy global sseu parameter\n");
 				return -EFAULT;
 			}
 
 			ret = get_sseu_config(&props->sseu, props->engine, &user_sseu);
 			if (ret) {
-				DRM_DEBUG("Invalid SSEU configuration\n");
+				drm_dbg(&perf->i915->drm,
+					"Invalid SSEU configuration\n");
 				return ret;
 			}
 			props->has_sseu = true;
@@ -3717,7 +3744,8 @@
 		}
 		case DRM_I915_PERF_PROP_POLL_OA_PERIOD:
 			if (value < 100000 /* 100us */) {
-				DRM_DEBUG("OA availability timer too small (%lluns < 100us)\n",
+				drm_dbg(&perf->i915->drm,
+					"OA availability timer too small (%lluns < 100us)\n",
 					  value);
 				return -EINVAL;
 			}
@@ -3767,16 +3795,15 @@
 	u32 known_open_flags;
 	int ret;
 
-	if (!perf->i915) {
-		DRM_DEBUG("i915 perf interface not available for this system\n");
+	if (!perf->i915)
 		return -ENOTSUPP;
-	}
 
 	known_open_flags = I915_PERF_FLAG_FD_CLOEXEC |
 			   I915_PERF_FLAG_FD_NONBLOCK |
 			   I915_PERF_FLAG_DISABLED;
 	if (param->flags & ~known_open_flags) {
-		DRM_DEBUG("Unknown drm_i915_perf_open_param flag\n");
+		drm_dbg(&perf->i915->drm,
+			"Unknown drm_i915_perf_open_param flag\n");
 		return -EINVAL;
 	}
 
@@ -3986,7 +4013,8 @@
 			goto addr_err;
 
 		if (!is_valid(perf, addr)) {
-			DRM_DEBUG("Invalid oa_reg address: %X\n", addr);
+			drm_dbg(&perf->i915->drm,
+				"Invalid oa_reg address: %X\n", addr);
 			err = -EINVAL;
 			goto addr_err;
 		}
@@ -4008,8 +4036,8 @@
 	return ERR_PTR(err);
 }
 
-static ssize_t show_dynamic_id(struct device *dev,
-			       struct device_attribute *attr,
+static ssize_t show_dynamic_id(struct kobject *kobj,
+			       struct kobj_attribute *attr,
 			       char *buf)
 {
 	struct i915_oa_config *oa_config =
@@ -4059,31 +4087,33 @@
 	struct i915_oa_reg *regs;
 	int err, id;
 
-	if (!perf->i915) {
-		DRM_DEBUG("i915 perf interface not available for this system\n");
+	if (!perf->i915)
 		return -ENOTSUPP;
-	}
 
 	if (!perf->metrics_kobj) {
-		DRM_DEBUG("OA metrics weren't advertised via sysfs\n");
+		drm_dbg(&perf->i915->drm,
+			"OA metrics weren't advertised via sysfs\n");
 		return -EINVAL;
 	}
 
 	if (i915_perf_stream_paranoid && !perfmon_capable()) {
-		DRM_DEBUG("Insufficient privileges to add i915 OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Insufficient privileges to add i915 OA config\n");
 		return -EACCES;
 	}
 
 	if ((!args->mux_regs_ptr || !args->n_mux_regs) &&
 	    (!args->boolean_regs_ptr || !args->n_boolean_regs) &&
 	    (!args->flex_regs_ptr || !args->n_flex_regs)) {
-		DRM_DEBUG("No OA registers given\n");
+		drm_dbg(&perf->i915->drm,
+			"No OA registers given\n");
 		return -EINVAL;
 	}
 
 	oa_config = kzalloc(sizeof(*oa_config), GFP_KERNEL);
 	if (!oa_config) {
-		DRM_DEBUG("Failed to allocate memory for the OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Failed to allocate memory for the OA config\n");
 		return -ENOMEM;
 	}
 
@@ -4091,7 +4121,8 @@
 	kref_init(&oa_config->ref);
 
 	if (!uuid_is_valid(args->uuid)) {
-		DRM_DEBUG("Invalid uuid format for OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Invalid uuid format for OA config\n");
 		err = -EINVAL;
 		goto reg_err;
 	}
@@ -4108,7 +4139,8 @@
 			     args->n_mux_regs);
 
 	if (IS_ERR(regs)) {
-		DRM_DEBUG("Failed to create OA config for mux_regs\n");
+		drm_dbg(&perf->i915->drm,
+			"Failed to create OA config for mux_regs\n");
 		err = PTR_ERR(regs);
 		goto reg_err;
 	}
@@ -4121,7 +4153,8 @@
 			     args->n_boolean_regs);
 
 	if (IS_ERR(regs)) {
-		DRM_DEBUG("Failed to create OA config for b_counter_regs\n");
+		drm_dbg(&perf->i915->drm,
+			"Failed to create OA config for b_counter_regs\n");
 		err = PTR_ERR(regs);
 		goto reg_err;
 	}
@@ -4140,7 +4173,8 @@
 				     args->n_flex_regs);
 
 		if (IS_ERR(regs)) {
-			DRM_DEBUG("Failed to create OA config for flex_regs\n");
+			drm_dbg(&perf->i915->drm,
+				"Failed to create OA config for flex_regs\n");
 			err = PTR_ERR(regs);
 			goto reg_err;
 		}
@@ -4156,7 +4190,8 @@
 	 */
 	idr_for_each_entry(&perf->metrics_idr, tmp, id) {
 		if (!strcmp(tmp->uuid, oa_config->uuid)) {
-			DRM_DEBUG("OA config already exists with this uuid\n");
+			drm_dbg(&perf->i915->drm,
+				"OA config already exists with this uuid\n");
 			err = -EADDRINUSE;
 			goto sysfs_err;
 		}
@@ -4164,7 +4199,8 @@
 
 	err = create_dynamic_oa_sysfs_entry(perf, oa_config);
 	if (err) {
-		DRM_DEBUG("Failed to create sysfs entry for OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Failed to create sysfs entry for OA config\n");
 		goto sysfs_err;
 	}
 
@@ -4173,22 +4209,25 @@
 				  oa_config, 2,
 				  0, GFP_KERNEL);
 	if (oa_config->id < 0) {
-		DRM_DEBUG("Failed to create sysfs entry for OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Failed to create sysfs entry for OA config\n");
 		err = oa_config->id;
 		goto sysfs_err;
 	}
+	id = oa_config->id;
 
+	drm_dbg(&perf->i915->drm,
+		"Added config %s id=%i\n", oa_config->uuid, oa_config->id);
 	mutex_unlock(&perf->metrics_lock);
 
-	DRM_DEBUG("Added config %s id=%i\n", oa_config->uuid, oa_config->id);
-
-	return oa_config->id;
+	return id;
 
 sysfs_err:
 	mutex_unlock(&perf->metrics_lock);
 reg_err:
 	i915_oa_config_put(oa_config);
-	DRM_DEBUG("Failed to add new OA config\n");
+	drm_dbg(&perf->i915->drm,
+		"Failed to add new OA config\n");
 	return err;
 }
 
@@ -4211,13 +4250,12 @@
 	struct i915_oa_config *oa_config;
 	int ret;
 
-	if (!perf->i915) {
-		DRM_DEBUG("i915 perf interface not available for this system\n");
+	if (!perf->i915)
 		return -ENOTSUPP;
-	}
 
 	if (i915_perf_stream_paranoid && !perfmon_capable()) {
-		DRM_DEBUG("Insufficient privileges to remove i915 OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Insufficient privileges to remove i915 OA config\n");
 		return -EACCES;
 	}
 
@@ -4227,7 +4265,8 @@
 
 	oa_config = idr_find(&perf->metrics_idr, *arg);
 	if (!oa_config) {
-		DRM_DEBUG("Failed to remove unknown OA config\n");
+		drm_dbg(&perf->i915->drm,
+			"Failed to remove unknown OA config\n");
 		ret = -ENOENT;
 		goto err_unlock;
 	}
@@ -4240,7 +4279,8 @@
 
 	mutex_unlock(&perf->metrics_lock);
 
-	DRM_DEBUG("Removed config %s id=%i\n", oa_config->uuid, oa_config->id);
+	drm_dbg(&perf->i915->drm,
+		"Removed config %s id=%i\n", oa_config->uuid, oa_config->id);
 
 	i915_oa_config_put(oa_config);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_perf_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_perf_types.h
@@ -55,7 +55,7 @@
 
 	struct attribute_group sysfs_metric;
 	struct attribute *attrs[2];
-	struct device_attribute sysfs_metric_id;
+	struct kobj_attribute sysfs_metric_id;
 
 	struct kref ref;
 	struct rcu_head rcu;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_pmu.c
@@ -761,9 +761,18 @@
 
 static void i915_pmu_event_stop(struct perf_event *event, int flags)
 {
+	struct drm_i915_private *i915 =
+		container_of(event->pmu, typeof(*i915), pmu.base);
+	struct i915_pmu *pmu = &i915->pmu;
+
+	if (pmu->closed)
+		goto out;
+
 	if (flags & PERF_EF_UPDATE)
 		i915_pmu_event_read(event);
 	i915_pmu_disable(event);
+
+out:
 	event->hw.state = PERF_HES_STOPPED;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_reg.h
@@ -2669,6 +2669,12 @@
 #define   GAMT_CHKN_DISABLE_DYNAMIC_CREDIT_SHARING	(1 << 28)
 #define   GAMT_CHKN_DISABLE_I2M_CYCLE_ON_WR_PORT	(1 << 24)
 
+#define GEN8_RTCR	_MMIO(0x4260)
+#define GEN8_M1TCR	_MMIO(0x4264)
+#define GEN8_M2TCR	_MMIO(0x4268)
+#define GEN8_BTCR	_MMIO(0x426c)
+#define GEN8_VTCR	_MMIO(0x4270)
+
 #if 0
 #define PRB0_TAIL	_MMIO(0x2030)
 #define PRB0_HEAD	_MMIO(0x2034)
@@ -2763,6 +2769,11 @@
 #define   FAULT_VA_HIGH_BITS		(0xf << 0)
 #define   FAULT_GTT_SEL			(1 << 4)
 
+#define GEN12_GFX_TLB_INV_CR	_MMIO(0xced8)
+#define GEN12_VD_TLB_INV_CR	_MMIO(0xcedc)
+#define GEN12_VE_TLB_INV_CR	_MMIO(0xcee0)
+#define GEN12_BLT_TLB_INV_CR	_MMIO(0xcee4)
+
 #define GEN12_AUX_ERR_DBG		_MMIO(0x43f4)
 
 #define FPGA_DBG		_MMIO(0x42300)
@@ -4509,11 +4520,9 @@
  * HSW PSR registers are relative to DDIA(_DDI_BUF_CTL_A + 0x800) with just one
  * instance of it
  */
-#define _HSW_EDP_PSR_BASE			0x64800
 #define _SRD_CTL_A				0x60800
 #define _SRD_CTL_EDP				0x6f800
-#define _PSR_ADJ(tran, reg)			(_TRANS2(tran, reg) - dev_priv->hsw_psr_mmio_adjust)
-#define EDP_PSR_CTL(tran)			_MMIO(_PSR_ADJ(tran, _SRD_CTL_A))
+#define EDP_PSR_CTL(tran)			_MMIO(_TRANS2(tran, _SRD_CTL_A))
 #define   EDP_PSR_ENABLE			(1 << 31)
 #define   BDW_PSR_SINGLE_FRAME			(1 << 30)
 #define   EDP_PSR_RESTORE_PSR_ACTIVE_CTX_MASK	(1 << 29) /* SW can't modify */
@@ -4557,22 +4566,13 @@
 #define   EDP_PSR_POST_EXIT(trans)		(0x2 << _EDP_PSR_TRANS_SHIFT(trans))
 #define   EDP_PSR_PRE_ENTRY(trans)		(0x1 << _EDP_PSR_TRANS_SHIFT(trans))
 
-#define _SRD_AUX_CTL_A				0x60810
-#define _SRD_AUX_CTL_EDP			0x6f810
-#define EDP_PSR_AUX_CTL(tran)			_MMIO(_PSR_ADJ(tran, _SRD_AUX_CTL_A))
-#define   EDP_PSR_AUX_CTL_TIME_OUT_MASK		(3 << 26)
-#define   EDP_PSR_AUX_CTL_MESSAGE_SIZE_MASK	(0x1f << 20)
-#define   EDP_PSR_AUX_CTL_PRECHARGE_2US_MASK	(0xf << 16)
-#define   EDP_PSR_AUX_CTL_ERROR_INTERRUPT	(1 << 11)
-#define   EDP_PSR_AUX_CTL_BIT_CLOCK_2X_MASK	(0x7ff)
-
 #define _SRD_AUX_DATA_A				0x60814
 #define _SRD_AUX_DATA_EDP			0x6f814
-#define EDP_PSR_AUX_DATA(tran, i)		_MMIO(_PSR_ADJ(tran, _SRD_AUX_DATA_A) + (i) + 4) /* 5 registers */
+#define EDP_PSR_AUX_DATA(tran, i)		_MMIO(_TRANS2(tran, _SRD_AUX_DATA_A) + (i) + 4) /* 5 registers */
 
 #define _SRD_STATUS_A				0x60840
 #define _SRD_STATUS_EDP				0x6f840
-#define EDP_PSR_STATUS(tran)			_MMIO(_PSR_ADJ(tran, _SRD_STATUS_A))
+#define EDP_PSR_STATUS(tran)			_MMIO(_TRANS2(tran, _SRD_STATUS_A))
 #define   EDP_PSR_STATUS_STATE_MASK		(7 << 29)
 #define   EDP_PSR_STATUS_STATE_SHIFT		29
 #define   EDP_PSR_STATUS_STATE_IDLE		(0 << 29)
@@ -4599,13 +4599,13 @@
 
 #define _SRD_PERF_CNT_A			0x60844
 #define _SRD_PERF_CNT_EDP		0x6f844
-#define EDP_PSR_PERF_CNT(tran)		_MMIO(_PSR_ADJ(tran, _SRD_PERF_CNT_A))
+#define EDP_PSR_PERF_CNT(tran)		_MMIO(_TRANS2(tran, _SRD_PERF_CNT_A))
 #define   EDP_PSR_PERF_CNT_MASK		0xffffff
 
 /* PSR_MASK on SKL+ */
 #define _SRD_DEBUG_A				0x60860
 #define _SRD_DEBUG_EDP				0x6f860
-#define EDP_PSR_DEBUG(tran)			_MMIO(_PSR_ADJ(tran, _SRD_DEBUG_A))
+#define EDP_PSR_DEBUG(tran)			_MMIO(_TRANS2(tran, _SRD_DEBUG_A))
 #define   EDP_PSR_DEBUG_MASK_MAX_SLEEP         (1 << 28)
 #define   EDP_PSR_DEBUG_MASK_LPSP              (1 << 27)
 #define   EDP_PSR_DEBUG_MASK_MEMUP             (1 << 26)
@@ -7447,7 +7447,7 @@
 #define _SEL_FETCH_PLANE_BASE_6_A		0x70940
 #define _SEL_FETCH_PLANE_BASE_7_A		0x70960
 #define _SEL_FETCH_PLANE_BASE_CUR_A		0x70880
-#define _SEL_FETCH_PLANE_BASE_1_B		0x70990
+#define _SEL_FETCH_PLANE_BASE_1_B		0x71890
 
 #define _SEL_FETCH_PLANE_BASE_A(plane) _PICK(plane, \
 					     _SEL_FETCH_PLANE_BASE_1_A, \
@@ -7807,6 +7807,22 @@
 /* MMIO address range for DMC program (0x80000 - 0x82FFF) */
 #define DMC_MMIO_START_RANGE	0x80000
 #define DMC_MMIO_END_RANGE	0x8FFFF
+#define DMC_V1_MMIO_START_RANGE	0x80000
+#define TGL_MAIN_MMIO_START	0x8F000
+#define TGL_MAIN_MMIO_END	0x8FFFF
+#define _TGL_PIPEA_MMIO_START	0x92000
+#define _TGL_PIPEA_MMIO_END	0x93FFF
+#define _TGL_PIPEB_MMIO_START	0x96000
+#define _TGL_PIPEB_MMIO_END	0x97FFF
+#define ADLP_PIPE_MMIO_START	0x5F000
+#define ADLP_PIPE_MMIO_END	0x5FFFF
+
+#define TGL_PIPE_MMIO_START(dmc_id)	_PICK_EVEN(((dmc_id) - 1), _TGL_PIPEA_MMIO_START,\
+						_TGL_PIPEB_MMIO_START)
+
+#define TGL_PIPE_MMIO_END(dmc_id)	_PICK_EVEN(((dmc_id) - 1), _TGL_PIPEA_MMIO_END,\
+						_TGL_PIPEB_MMIO_END)
+
 #define SKL_DMC_DC3_DC5_COUNT	_MMIO(0x80030)
 #define SKL_DMC_DC5_DC6_COUNT	_MMIO(0x8002C)
 #define BXT_DMC_DC3_DC5_COUNT	_MMIO(0x80038)
@@ -7814,7 +7830,8 @@
 #define TGL_DMC_DEBUG_DC6_COUNT	_MMIO(0x101088)
 #define DG1_DMC_DEBUG_DC5_COUNT	_MMIO(0x134154)
 
-#define DMC_DEBUG3		_MMIO(0x101090)
+#define TGL_DMC_DEBUG3		_MMIO(0x101090)
+#define DG1_DMC_DEBUG3		_MMIO(0x13415c)
 
 /* Display Internal Timeout Register */
 #define RM_TIMEOUT		_MMIO(0x42060)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_request.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_request.c
@@ -1596,6 +1596,8 @@
 							 &rq->dep,
 							 0);
 	}
+	if (prev)
+		i915_request_put(prev);
 
 	/*
 	 * Make sure that no request gazumped us - if it was allocated after
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_scheduler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_scheduler.c
@@ -506,6 +506,6 @@
 	return 0;
 
 err_priorities:
-	kmem_cache_destroy(slab_priorities);
+	kmem_cache_destroy(slab_dependencies);
 	return -ENOMEM;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_sw_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_sw_fence.c
@@ -49,7 +49,7 @@
 	debug_object_init(fence, &i915_sw_fence_debug_descr);
 }
 
-static inline void debug_fence_init_onstack(struct i915_sw_fence *fence)
+static inline __maybe_unused void debug_fence_init_onstack(struct i915_sw_fence *fence)
 {
 	debug_object_init_on_stack(fence, &i915_sw_fence_debug_descr);
 }
@@ -75,7 +75,7 @@
 	debug_object_destroy(fence, &i915_sw_fence_debug_descr);
 }
 
-static inline void debug_fence_free(struct i915_sw_fence *fence)
+static inline __maybe_unused void debug_fence_free(struct i915_sw_fence *fence)
 {
 	debug_object_free(fence, &i915_sw_fence_debug_descr);
 	smp_wmb(); /* flush the change in state before reallocation */
@@ -92,7 +92,7 @@
 {
 }
 
-static inline void debug_fence_init_onstack(struct i915_sw_fence *fence)
+static inline __maybe_unused void debug_fence_init_onstack(struct i915_sw_fence *fence)
 {
 }
 
@@ -113,7 +113,7 @@
 {
 }
 
-static inline void debug_fence_free(struct i915_sw_fence *fence)
+static inline __maybe_unused void debug_fence_free(struct i915_sw_fence *fence)
 {
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_switcheroo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_switcheroo.c
@@ -18,6 +18,10 @@
 		dev_err(&pdev->dev, "DRM not initialized, aborting switch.\n");
 		return;
 	}
+	if (!HAS_DISPLAY(i915)) {
+		dev_err(&pdev->dev, "Device state not initialized, aborting switch.\n");
+		return;
+	}
 
 	if (state == VGA_SWITCHEROO_ON) {
 		drm_info(&i915->drm, "switched on\n");
@@ -43,7 +47,7 @@
 	 * locking inversion with the driver load path. And the access here is
 	 * completely racy anyway. So don't bother with locking for now.
 	 */
-	return i915 && atomic_read(&i915->drm.open_count) == 0;
+	return i915 && HAS_DISPLAY(i915) && atomic_read(&i915->drm.open_count) == 0;
 }
 
 static const struct vga_switcheroo_client_ops i915_switcheroo_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_sysfs.c
@@ -445,7 +445,14 @@
 	struct device *kdev = kobj_to_dev(kobj);
 	struct drm_i915_private *i915 = kdev_minor_to_i915(kdev);
 	struct i915_gpu_coredump *gpu;
-	ssize_t ret;
+	ssize_t ret = 0;
+
+	/*
+	 * FIXME: Concurrent clients triggering resets and reading + clearing
+	 * dumps can cause inconsistent sysfs reads when a user calls in with a
+	 * non-zero offset to complete a prior partial read but the
+	 * gpu_coredump has been cleared or replaced.
+	 */
 
 	gpu = i915_first_error_state(i915);
 	if (IS_ERR(gpu)) {
@@ -457,8 +464,10 @@
 		const char *str = "No error state collected\n";
 		size_t len = strlen(str);
 
-		ret = min_t(size_t, count, len - off);
-		memcpy(buf, str + off, ret);
+		if (off < len) {
+			ret = min_t(size_t, count, len - off);
+			memcpy(buf, str + off, ret);
+		}
 	}
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_ttm_buddy_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_ttm_buddy_manager.c
@@ -109,6 +109,7 @@
 	i915_buddy_free_list(mm, &bman_res->blocks);
 	mutex_unlock(&bman->lock);
 err_free_res:
+	ttm_resource_fini(man, &bman_res->base);
 	kfree(bman_res);
 	return err;
 }
@@ -123,6 +124,7 @@
 	i915_buddy_free_list(&bman->mm, &bman_res->blocks);
 	mutex_unlock(&bman->lock);
 
+	ttm_resource_fini(man, res);
 	kfree(bman_res);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/i915_vma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/i915_vma.c
@@ -376,6 +376,7 @@
 	u32 bind_flags;
 	u32 vma_flags;
 
+	lockdep_assert_held(&vma->vm->mutex);
 	GEM_BUG_ON(!drm_mm_node_allocated(&vma->node));
 	GEM_BUG_ON(vma->size > vma->node.size);
 
@@ -434,6 +435,9 @@
 		vma->ops->bind_vma(vma->vm, NULL, vma, cache_level, bind_flags);
 	}
 
+	if (vma->obj)
+		set_bit(I915_BO_WAS_BOUND_BIT, &vma->obj->flags);
+
 	atomic_or(bind_flags, &vma->flags);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/intel_pch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/intel_pch.c
@@ -108,6 +108,7 @@
 		/* Comet Lake V PCH is based on KBP, which is SPT compatible */
 		return PCH_SPT;
 	case INTEL_PCH_ICP_DEVICE_ID_TYPE:
+	case INTEL_PCH_ICP2_DEVICE_ID_TYPE:
 		drm_dbg_kms(&dev_priv->drm, "Found Ice Lake PCH\n");
 		drm_WARN_ON(&dev_priv->drm, !IS_ICELAKE(dev_priv));
 		return PCH_ICP;
@@ -123,7 +124,6 @@
 			    !IS_GEN9_BC(dev_priv));
 		return PCH_TGP;
 	case INTEL_PCH_JSP_DEVICE_ID_TYPE:
-	case INTEL_PCH_JSP2_DEVICE_ID_TYPE:
 		drm_dbg_kms(&dev_priv->drm, "Found Jasper Lake PCH\n");
 		drm_WARN_ON(&dev_priv->drm, !IS_JSL_EHL(dev_priv));
 		return PCH_JSP;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/intel_pch.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/intel_pch.h
@@ -50,11 +50,11 @@
 #define INTEL_PCH_CMP2_DEVICE_ID_TYPE		0x0680
 #define INTEL_PCH_CMP_V_DEVICE_ID_TYPE		0xA380
 #define INTEL_PCH_ICP_DEVICE_ID_TYPE		0x3480
+#define INTEL_PCH_ICP2_DEVICE_ID_TYPE		0x3880
 #define INTEL_PCH_MCC_DEVICE_ID_TYPE		0x4B00
 #define INTEL_PCH_TGP_DEVICE_ID_TYPE		0xA080
 #define INTEL_PCH_TGP2_DEVICE_ID_TYPE		0x4380
 #define INTEL_PCH_JSP_DEVICE_ID_TYPE		0x4D80
-#define INTEL_PCH_JSP2_DEVICE_ID_TYPE		0x3880
 #define INTEL_PCH_ADP_DEVICE_ID_TYPE		0x7A80
 #define INTEL_PCH_ADP2_DEVICE_ID_TYPE		0x5180
 #define INTEL_PCH_P2X_DEVICE_ID_TYPE		0x7100
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/intel_pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/intel_pm.c
@@ -2863,7 +2863,7 @@
 }
 
 static void intel_read_wm_latency(struct drm_i915_private *dev_priv,
-				  u16 wm[8])
+				  u16 wm[])
 {
 	struct intel_uncore *uncore = &dev_priv->uncore;
 
@@ -3063,9 +3063,9 @@
 	 * The BIOS provided WM memory latency values are often
 	 * inadequate for high resolution displays. Adjust them.
 	 */
-	changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
-		ilk_increase_wm_latency(dev_priv, dev_priv->wm.spr_latency, 12) |
-		ilk_increase_wm_latency(dev_priv, dev_priv->wm.cur_latency, 12);
+	changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12);
+	changed |= ilk_increase_wm_latency(dev_priv, dev_priv->wm.spr_latency, 12);
+	changed |= ilk_increase_wm_latency(dev_priv, dev_priv->wm.cur_latency, 12);
 
 	if (!changed)
 		return;
@@ -3713,8 +3713,7 @@
 		MISSING_CASE(DISPLAY_VER(dev_priv));
 	}
 
-	/* Default to an unusable block time */
-	dev_priv->sagv_block_time_us = -1;
+	dev_priv->sagv_block_time_us = 0;
 }
 
 /*
@@ -4020,6 +4019,17 @@
 			return ret;
 	}
 
+	if (intel_can_enable_sagv(dev_priv, new_bw_state) !=
+	    intel_can_enable_sagv(dev_priv, old_bw_state)) {
+		ret = intel_atomic_serialize_global_state(&new_bw_state->base);
+		if (ret)
+			return ret;
+	} else if (new_bw_state->pipe_sagv_reject != old_bw_state->pipe_sagv_reject) {
+		ret = intel_atomic_lock_global_state(&new_bw_state->base);
+		if (ret)
+			return ret;
+	}
+
 	for_each_new_intel_crtc_in_state(state, crtc,
 					 new_crtc_state, i) {
 		struct skl_pipe_wm *pipe_wm = &new_crtc_state->wm.skl.optimal;
@@ -4035,17 +4045,6 @@
 			intel_can_enable_sagv(dev_priv, new_bw_state);
 	}
 
-	if (intel_can_enable_sagv(dev_priv, new_bw_state) !=
-	    intel_can_enable_sagv(dev_priv, old_bw_state)) {
-		ret = intel_atomic_serialize_global_state(&new_bw_state->base);
-		if (ret)
-			return ret;
-	} else if (new_bw_state->pipe_sagv_reject != old_bw_state->pipe_sagv_reject) {
-		ret = intel_atomic_lock_global_state(&new_bw_state->base);
-		if (ret)
-			return ret;
-	}
-
 	return 0;
 }
 
@@ -4708,6 +4707,10 @@
 };
 
 static const struct dbuf_slice_conf_entry adlp_allowed_dbufs[] = {
+	/*
+	 * Keep the join_mbus cases first so check_mbus_joined()
+	 * will prefer them over the !join_mbus cases.
+	 */
 	{
 		.active_pipes = BIT(PIPE_A),
 		.dbuf_mask = {
@@ -4723,6 +4726,20 @@
 		.join_mbus = true,
 	},
 	{
+		.active_pipes = BIT(PIPE_A),
+		.dbuf_mask = {
+			[PIPE_A] = BIT(DBUF_S1) | BIT(DBUF_S2),
+		},
+		.join_mbus = false,
+	},
+	{
+		.active_pipes = BIT(PIPE_B),
+		.dbuf_mask = {
+			[PIPE_B] = BIT(DBUF_S3) | BIT(DBUF_S4),
+		},
+		.join_mbus = false,
+	},
+	{
 		.active_pipes = BIT(PIPE_A) | BIT(PIPE_B),
 		.dbuf_mask = {
 			[PIPE_A] = BIT(DBUF_S1) | BIT(DBUF_S2),
@@ -4826,7 +4843,7 @@
 {
 	int i;
 
-	for (i = 0; i < dbuf_slices[i].active_pipes; i++) {
+	for (i = 0; dbuf_slices[i].active_pipes != 0; i++) {
 		if (dbuf_slices[i].active_pipes == active_pipes)
 			return dbuf_slices[i].join_mbus;
 	}
@@ -4838,13 +4855,14 @@
 	return check_mbus_joined(active_pipes, adlp_allowed_dbufs);
 }
 
-static u8 compute_dbuf_slices(enum pipe pipe, u8 active_pipes,
+static u8 compute_dbuf_slices(enum pipe pipe, u8 active_pipes, bool join_mbus,
 			      const struct dbuf_slice_conf_entry *dbuf_slices)
 {
 	int i;
 
-	for (i = 0; i < dbuf_slices[i].active_pipes; i++) {
-		if (dbuf_slices[i].active_pipes == active_pipes)
+	for (i = 0; dbuf_slices[i].active_pipes != 0; i++) {
+		if (dbuf_slices[i].active_pipes == active_pipes &&
+		    dbuf_slices[i].join_mbus == join_mbus)
 			return dbuf_slices[i].dbuf_mask[pipe];
 	}
 	return 0;
@@ -4855,7 +4873,7 @@
  * returns correspondent DBuf slice mask as stated in BSpec for particular
  * platform.
  */
-static u8 icl_compute_dbuf_slices(enum pipe pipe, u8 active_pipes)
+static u8 icl_compute_dbuf_slices(enum pipe pipe, u8 active_pipes, bool join_mbus)
 {
 	/*
 	 * FIXME: For ICL this is still a bit unclear as prev BSpec revision
@@ -4869,37 +4887,41 @@
 	 * still here - we will need it once those additional constraints
 	 * pop up.
 	 */
-	return compute_dbuf_slices(pipe, active_pipes, icl_allowed_dbufs);
+	return compute_dbuf_slices(pipe, active_pipes, join_mbus,
+				   icl_allowed_dbufs);
 }
 
-static u8 tgl_compute_dbuf_slices(enum pipe pipe, u8 active_pipes)
+static u8 tgl_compute_dbuf_slices(enum pipe pipe, u8 active_pipes, bool join_mbus)
 {
-	return compute_dbuf_slices(pipe, active_pipes, tgl_allowed_dbufs);
+	return compute_dbuf_slices(pipe, active_pipes, join_mbus,
+				   tgl_allowed_dbufs);
 }
 
-static u32 adlp_compute_dbuf_slices(enum pipe pipe, u32 active_pipes)
+static u8 adlp_compute_dbuf_slices(enum pipe pipe, u8 active_pipes, bool join_mbus)
 {
-	return compute_dbuf_slices(pipe, active_pipes, adlp_allowed_dbufs);
+	return compute_dbuf_slices(pipe, active_pipes, join_mbus,
+				   adlp_allowed_dbufs);
 }
 
-static u32 dg2_compute_dbuf_slices(enum pipe pipe, u32 active_pipes)
+static u8 dg2_compute_dbuf_slices(enum pipe pipe, u8 active_pipes, bool join_mbus)
 {
-	return compute_dbuf_slices(pipe, active_pipes, dg2_allowed_dbufs);
+	return compute_dbuf_slices(pipe, active_pipes, join_mbus,
+				   dg2_allowed_dbufs);
 }
 
-static u8 skl_compute_dbuf_slices(struct intel_crtc *crtc, u8 active_pipes)
+static u8 skl_compute_dbuf_slices(struct intel_crtc *crtc, u8 active_pipes, bool join_mbus)
 {
 	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
 	enum pipe pipe = crtc->pipe;
 
 	if (IS_DG2(dev_priv))
-		return dg2_compute_dbuf_slices(pipe, active_pipes);
+		return dg2_compute_dbuf_slices(pipe, active_pipes, join_mbus);
 	else if (IS_ALDERLAKE_P(dev_priv))
-		return adlp_compute_dbuf_slices(pipe, active_pipes);
+		return adlp_compute_dbuf_slices(pipe, active_pipes, join_mbus);
 	else if (DISPLAY_VER(dev_priv) == 12)
-		return tgl_compute_dbuf_slices(pipe, active_pipes);
+		return tgl_compute_dbuf_slices(pipe, active_pipes, join_mbus);
 	else if (DISPLAY_VER(dev_priv) == 11)
-		return icl_compute_dbuf_slices(pipe, active_pipes);
+		return icl_compute_dbuf_slices(pipe, active_pipes, join_mbus);
 	/*
 	 * For anything else just return one slice yet.
 	 * Should be extended for other platforms.
@@ -5380,10 +5402,16 @@
 	wp->y_tiled = modifier == I915_FORMAT_MOD_Y_TILED ||
 		      modifier == I915_FORMAT_MOD_Yf_TILED ||
 		      modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
-		      modifier == I915_FORMAT_MOD_Yf_TILED_CCS;
+		      modifier == I915_FORMAT_MOD_Yf_TILED_CCS ||
+		      modifier == I915_FORMAT_MOD_Y_TILED_GEN12_RC_CCS ||
+		      modifier == I915_FORMAT_MOD_Y_TILED_GEN12_MC_CCS ||
+		      modifier == I915_FORMAT_MOD_Y_TILED_GEN12_RC_CCS_CC;
 	wp->x_tiled = modifier == I915_FORMAT_MOD_X_TILED;
 	wp->rc_surface = modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
-			 modifier == I915_FORMAT_MOD_Yf_TILED_CCS;
+			 modifier == I915_FORMAT_MOD_Yf_TILED_CCS ||
+			 modifier == I915_FORMAT_MOD_Y_TILED_GEN12_RC_CCS ||
+			 modifier == I915_FORMAT_MOD_Y_TILED_GEN12_MC_CCS ||
+			 modifier == I915_FORMAT_MOD_Y_TILED_GEN12_RC_CCS_CC;
 	wp->is_planar = intel_format_info_is_yuv_semiplanar(format, modifier);
 
 	wp->width = width;
@@ -5612,7 +5640,7 @@
 	result->min_ddb_alloc = max(min_ddb_alloc, blocks) + 1;
 	result->enable = true;
 
-	if (DISPLAY_VER(dev_priv) < 12)
+	if (DISPLAY_VER(dev_priv) < 12 && dev_priv->sagv_block_time_us)
 		result->can_sagv = latency >= dev_priv->sagv_block_time_us;
 }
 
@@ -5643,7 +5671,10 @@
 	struct drm_i915_private *dev_priv = to_i915(crtc_state->uapi.crtc->dev);
 	struct skl_wm_level *sagv_wm = &plane_wm->sagv.wm0;
 	struct skl_wm_level *levels = plane_wm->wm;
-	unsigned int latency = dev_priv->wm.skl_latency[0] + dev_priv->sagv_block_time_us;
+	unsigned int latency = 0;
+
+	if (dev_priv->sagv_block_time_us)
+		latency = dev_priv->sagv_block_time_us + dev_priv->wm.skl_latency[0];
 
 	skl_compute_plane_wm(crtc_state, 0, latency,
 			     wm_params, &levels[0],
@@ -6110,11 +6141,16 @@
 			return ret;
 	}
 
+	if (IS_ALDERLAKE_P(dev_priv))
+		new_dbuf_state->joined_mbus =
+			adlp_check_mbus_joined(new_dbuf_state->active_pipes);
+
 	for_each_intel_crtc(&dev_priv->drm, crtc) {
 		enum pipe pipe = crtc->pipe;
 
 		new_dbuf_state->slices[pipe] =
-			skl_compute_dbuf_slices(crtc, new_dbuf_state->active_pipes);
+			skl_compute_dbuf_slices(crtc, new_dbuf_state->active_pipes,
+						new_dbuf_state->joined_mbus);
 
 		if (old_dbuf_state->slices[pipe] == new_dbuf_state->slices[pipe])
 			continue;
@@ -6126,9 +6162,6 @@
 
 	new_dbuf_state->enabled_slices = intel_dbuf_enabled_slices(new_dbuf_state);
 
-	if (IS_ALDERLAKE_P(dev_priv))
-		new_dbuf_state->joined_mbus = adlp_check_mbus_joined(new_dbuf_state->active_pipes);
-
 	if (old_dbuf_state->enabled_slices != new_dbuf_state->enabled_slices ||
 	    old_dbuf_state->joined_mbus != new_dbuf_state->joined_mbus) {
 		ret = intel_atomic_serialize_global_state(&new_dbuf_state->base);
@@ -6609,8 +6642,12 @@
 		enum pipe pipe = crtc->pipe;
 		unsigned int mbus_offset;
 		enum plane_id plane_id;
+		u8 slices;
 
-		skl_pipe_wm_get_hw_state(crtc, &crtc_state->wm.skl.optimal);
+		memset(&crtc_state->wm.skl.optimal, 0,
+		       sizeof(crtc_state->wm.skl.optimal));
+		if (crtc_state->hw.active)
+			skl_pipe_wm_get_hw_state(crtc, &crtc_state->wm.skl.optimal);
 		crtc_state->wm.skl.raw = crtc_state->wm.skl.optimal;
 
 		memset(&dbuf_state->ddb[pipe], 0, sizeof(dbuf_state->ddb[pipe]));
@@ -6621,6 +6658,9 @@
 			struct skl_ddb_entry *ddb_uv =
 				&crtc_state->wm.skl.plane_ddb_uv[plane_id];
 
+			if (!crtc_state->hw.active)
+				continue;
+
 			skl_ddb_get_hw_plane_state(dev_priv, crtc->pipe,
 						   plane_id, ddb_y, ddb_uv);
 
@@ -6628,19 +6668,22 @@
 			skl_ddb_entry_union(&dbuf_state->ddb[pipe], ddb_uv);
 		}
 
-		dbuf_state->slices[pipe] =
-			skl_compute_dbuf_slices(crtc, dbuf_state->active_pipes);
-
 		dbuf_state->weight[pipe] = intel_crtc_ddb_weight(crtc_state);
 
 		/*
 		 * Used for checking overlaps, so we need absolute
 		 * offsets instead of MBUS relative offsets.
 		 */
-		mbus_offset = mbus_ddb_offset(dev_priv, dbuf_state->slices[pipe]);
+		slices = skl_compute_dbuf_slices(crtc, dbuf_state->active_pipes,
+						 dbuf_state->joined_mbus);
+		mbus_offset = mbus_ddb_offset(dev_priv, slices);
 		crtc_state->wm.skl.ddb.start = mbus_offset + dbuf_state->ddb[pipe].start;
 		crtc_state->wm.skl.ddb.end = mbus_offset + dbuf_state->ddb[pipe].end;
 
+		/* The slices actually used by the planes on the pipe */
+		dbuf_state->slices[pipe] =
+			skl_ddb_dbuf_slice_mask(dev_priv, &crtc_state->wm.skl.ddb);
+
 		drm_dbg_kms(&dev_priv->drm,
 			    "[CRTC:%d:%s] dbuf slices 0x%x, ddb (%d - %d), active pipes 0x%x, mbus joined: %s\n",
 			    crtc->base.base.id, crtc->base.name,
@@ -6652,6 +6695,74 @@
 	dbuf_state->enabled_slices = dev_priv->dbuf.enabled_slices;
 }
 
+static bool skl_dbuf_is_misconfigured(struct drm_i915_private *i915)
+{
+	const struct intel_dbuf_state *dbuf_state =
+		to_intel_dbuf_state(i915->dbuf.obj.state);
+	struct skl_ddb_entry entries[I915_MAX_PIPES] = {};
+	struct intel_crtc *crtc;
+
+	for_each_intel_crtc(&i915->drm, crtc) {
+		const struct intel_crtc_state *crtc_state =
+			to_intel_crtc_state(crtc->base.state);
+
+		entries[crtc->pipe] = crtc_state->wm.skl.ddb;
+	}
+
+	for_each_intel_crtc(&i915->drm, crtc) {
+		const struct intel_crtc_state *crtc_state =
+			to_intel_crtc_state(crtc->base.state);
+		u8 slices;
+
+		slices = skl_compute_dbuf_slices(crtc, dbuf_state->active_pipes,
+						 dbuf_state->joined_mbus);
+		if (dbuf_state->slices[crtc->pipe] & ~slices)
+			return true;
+
+		if (skl_ddb_allocation_overlaps(&crtc_state->wm.skl.ddb, entries,
+						I915_MAX_PIPES, crtc->pipe))
+			return true;
+	}
+
+	return false;
+}
+
+void skl_wm_sanitize(struct drm_i915_private *i915)
+{
+	struct intel_crtc *crtc;
+
+	/*
+	 * On TGL/RKL (at least) the BIOS likes to assign the planes
+	 * to the wrong DBUF slices. This will cause an infinite loop
+	 * in skl_commit_modeset_enables() as it can't find a way to
+	 * transition between the old bogus DBUF layout to the new
+	 * proper DBUF layout without DBUF allocation overlaps between
+	 * the planes (which cannot be allowed or else the hardware
+	 * may hang). If we detect a bogus DBUF layout just turn off
+	 * all the planes so that skl_commit_modeset_enables() can
+	 * simply ignore them.
+	 */
+	if (!skl_dbuf_is_misconfigured(i915))
+		return;
+
+	drm_dbg_kms(&i915->drm, "BIOS has misprogrammed the DBUF, disabling all planes\n");
+
+	for_each_intel_crtc(&i915->drm, crtc) {
+		struct intel_plane *plane = to_intel_plane(crtc->base.primary);
+		const struct intel_plane_state *plane_state =
+			to_intel_plane_state(plane->base.state);
+		struct intel_crtc_state *crtc_state =
+			to_intel_crtc_state(crtc->base.state);
+
+		if (plane_state->uapi.visible)
+			intel_plane_disable_noatomic(crtc, plane);
+
+		drm_WARN_ON(&i915->drm, crtc_state->active_planes != 0);
+
+		memset(&crtc_state->wm.skl.ddb, 0, sizeof(crtc_state->wm.skl.ddb));
+	}
+}
+
 static void ilk_pipe_wm_get_hw_state(struct intel_crtc *crtc)
 {
 	struct drm_device *dev = crtc->base.dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/intel_pm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/intel_pm.h
@@ -48,6 +48,7 @@
 			      struct skl_pipe_wm *out);
 void g4x_wm_sanitize(struct drm_i915_private *dev_priv);
 void vlv_wm_sanitize(struct drm_i915_private *dev_priv);
+void skl_wm_sanitize(struct drm_i915_private *dev_priv);
 bool intel_can_enable_sagv(struct drm_i915_private *dev_priv,
 			   const struct intel_bw_state *bw_state);
 void intel_sagv_pre_plane_update(struct intel_atomic_state *state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/intel_uncore.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/intel_uncore.c
@@ -718,7 +718,8 @@
 }
 
 static void __intel_uncore_forcewake_put(struct intel_uncore *uncore,
-					 enum forcewake_domains fw_domains)
+					 enum forcewake_domains fw_domains,
+					 bool delayed)
 {
 	struct intel_uncore_forcewake_domain *domain;
 	unsigned int tmp;
@@ -733,7 +734,11 @@
 			continue;
 		}
 
-		uncore->funcs.force_wake_put(uncore, domain->mask);
+		if (delayed &&
+		    !(domain->uncore->fw_domains_timer & domain->mask))
+			fw_domain_arm_timer(domain);
+		else
+			uncore->funcs.force_wake_put(uncore, domain->mask);
 	}
 }
 
@@ -754,7 +759,20 @@
 		return;
 
 	spin_lock_irqsave(&uncore->lock, irqflags);
-	__intel_uncore_forcewake_put(uncore, fw_domains);
+	__intel_uncore_forcewake_put(uncore, fw_domains, false);
+	spin_unlock_irqrestore(&uncore->lock, irqflags);
+}
+
+void intel_uncore_forcewake_put_delayed(struct intel_uncore *uncore,
+					enum forcewake_domains fw_domains)
+{
+	unsigned long irqflags;
+
+	if (!uncore->funcs.force_wake_put)
+		return;
+
+	spin_lock_irqsave(&uncore->lock, irqflags);
+	__intel_uncore_forcewake_put(uncore, fw_domains, true);
 	spin_unlock_irqrestore(&uncore->lock, irqflags);
 }
 
@@ -796,7 +814,7 @@
 	if (!uncore->funcs.force_wake_put)
 		return;
 
-	__intel_uncore_forcewake_put(uncore, fw_domains);
+	__intel_uncore_forcewake_put(uncore, fw_domains, false);
 }
 
 void assert_forcewakes_inactive(struct intel_uncore *uncore)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/intel_uncore.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/intel_uncore.h
@@ -229,6 +229,8 @@
 				enum forcewake_domains domains);
 void intel_uncore_forcewake_put(struct intel_uncore *uncore,
 				enum forcewake_domains domains);
+void intel_uncore_forcewake_put_delayed(struct intel_uncore *uncore,
+					enum forcewake_domains domains);
 void intel_uncore_forcewake_flush(struct intel_uncore *uncore,
 				  enum forcewake_domains fw_domains);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/selftests/i915_gem_gtt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/selftests/i915_gem_gtt.c
@@ -160,7 +160,7 @@
 		return PTR_ERR(ppgtt);
 
 	if (!ppgtt->vm.allocate_va_range)
-		goto err_ppgtt_cleanup;
+		goto ppgtt_vm_put;
 
 	/*
 	 * While we only allocate the page tables here and so we could
@@ -228,7 +228,7 @@
 			goto retry;
 	}
 	i915_gem_ww_ctx_fini(&ww);
-
+ppgtt_vm_put:
 	i915_vm_put(&ppgtt->vm);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/selftests/i915_request.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/selftests/i915_request.c
@@ -288,9 +288,18 @@
 	return intel_context_create_request(ce);
 }
 
-static int __igt_breadcrumbs_smoketest(void *arg)
+struct smoke_thread {
+	struct kthread_worker *worker;
+	struct kthread_work work;
+	struct smoketest *t;
+	bool stop;
+	int result;
+};
+
+static void __igt_breadcrumbs_smoketest(struct kthread_work *work)
 {
-	struct smoketest *t = arg;
+	struct smoke_thread *thread = container_of(work, typeof(*thread), work);
+	struct smoketest *t = thread->t;
 	const unsigned int max_batch = min(t->ncontexts, t->max_batch) - 1;
 	const unsigned int total = 4 * t->ncontexts + 1;
 	unsigned int num_waits = 0, num_fences = 0;
@@ -309,8 +318,10 @@
 	 */
 
 	requests = kcalloc(total, sizeof(*requests), GFP_KERNEL);
-	if (!requests)
-		return -ENOMEM;
+	if (!requests) {
+		thread->result = -ENOMEM;
+		return;
+	}
 
 	order = i915_random_order(total, &prng);
 	if (!order) {
@@ -318,7 +329,7 @@
 		goto out_requests;
 	}
 
-	while (!kthread_should_stop()) {
+	while (!READ_ONCE(thread->stop)) {
 		struct i915_sw_fence *submit, *wait;
 		unsigned int n, count;
 
@@ -426,7 +437,7 @@
 	kfree(order);
 out_requests:
 	kfree(requests);
-	return err;
+	thread->result = err;
 }
 
 static int mock_breadcrumbs_smoketest(void *arg)
@@ -439,7 +450,7 @@
 		.request_alloc = __mock_request_alloc
 	};
 	unsigned int ncpus = num_online_cpus();
-	struct task_struct **threads;
+	struct smoke_thread *threads;
 	unsigned int n;
 	int ret = 0;
 
@@ -468,28 +479,37 @@
 	}
 
 	for (n = 0; n < ncpus; n++) {
-		threads[n] = kthread_run(__igt_breadcrumbs_smoketest,
-					 &t, "igt/%d", n);
-		if (IS_ERR(threads[n])) {
-			ret = PTR_ERR(threads[n]);
+		struct kthread_worker *worker;
+
+		worker = kthread_create_worker(0, "igt/%d", n);
+		if (IS_ERR(worker)) {
+			ret = PTR_ERR(worker);
 			ncpus = n;
 			break;
 		}
 
-		get_task_struct(threads[n]);
+		threads[n].worker = worker;
+		threads[n].t = &t;
+		threads[n].stop = false;
+		threads[n].result = 0;
+
+		kthread_init_work(&threads[n].work,
+				  __igt_breadcrumbs_smoketest);
+		kthread_queue_work(worker, &threads[n].work);
 	}
 
-	yield(); /* start all threads before we begin */
 	msleep(jiffies_to_msecs(i915_selftest.timeout_jiffies));
 
 	for (n = 0; n < ncpus; n++) {
 		int err;
 
-		err = kthread_stop(threads[n]);
+		WRITE_ONCE(threads[n].stop, true);
+		kthread_flush_work(&threads[n].work);
+		err = READ_ONCE(threads[n].result);
 		if (err < 0 && !ret)
 			ret = err;
 
-		put_task_struct(threads[n]);
+		kthread_destroy_worker(threads[n].worker);
 	}
 	pr_info("Completed %lu waits for %lu fence across %d cpus\n",
 		atomic_long_read(&t.num_waits),
@@ -1291,9 +1311,18 @@
 	return err;
 }
 
-static int __live_parallel_engine1(void *arg)
+struct parallel_thread {
+	struct kthread_worker *worker;
+	struct kthread_work work;
+	struct intel_engine_cs *engine;
+	int result;
+};
+
+static void __live_parallel_engine1(struct kthread_work *work)
 {
-	struct intel_engine_cs *engine = arg;
+	struct parallel_thread *thread =
+		container_of(work, typeof(*thread), work);
+	struct intel_engine_cs *engine = thread->engine;
 	IGT_TIMEOUT(end_time);
 	unsigned long count;
 	int err = 0;
@@ -1324,12 +1353,14 @@
 	intel_engine_pm_put(engine);
 
 	pr_info("%s: %lu request + sync\n", engine->name, count);
-	return err;
+	thread->result = err;
 }
 
-static int __live_parallel_engineN(void *arg)
+static void __live_parallel_engineN(struct kthread_work *work)
 {
-	struct intel_engine_cs *engine = arg;
+	struct parallel_thread *thread =
+		container_of(work, typeof(*thread), work);
+	struct intel_engine_cs *engine = thread->engine;
 	IGT_TIMEOUT(end_time);
 	unsigned long count;
 	int err = 0;
@@ -1351,7 +1382,7 @@
 	intel_engine_pm_put(engine);
 
 	pr_info("%s: %lu requests\n", engine->name, count);
-	return err;
+	thread->result = err;
 }
 
 static bool wake_all(struct drm_i915_private *i915)
@@ -1377,9 +1408,11 @@
 	return -ETIME;
 }
 
-static int __live_parallel_spin(void *arg)
+static void __live_parallel_spin(struct kthread_work *work)
 {
-	struct intel_engine_cs *engine = arg;
+	struct parallel_thread *thread =
+		container_of(work, typeof(*thread), work);
+	struct intel_engine_cs *engine = thread->engine;
 	struct igt_spinner spin;
 	struct i915_request *rq;
 	int err = 0;
@@ -1392,7 +1425,8 @@
 
 	if (igt_spinner_init(&spin, engine->gt)) {
 		wake_all(engine->i915);
-		return -ENOMEM;
+		thread->result = -ENOMEM;
+		return;
 	}
 
 	intel_engine_pm_get(engine);
@@ -1425,22 +1459,22 @@
 
 out_spin:
 	igt_spinner_fini(&spin);
-	return err;
+	thread->result = err;
 }
 
 static int live_parallel_engines(void *arg)
 {
 	struct drm_i915_private *i915 = arg;
-	static int (* const func[])(void *arg) = {
+	static void (* const func[])(struct kthread_work *) = {
 		__live_parallel_engine1,
 		__live_parallel_engineN,
 		__live_parallel_spin,
 		NULL,
 	};
 	const unsigned int nengines = num_uabi_engines(i915);
+	struct parallel_thread *threads;
 	struct intel_engine_cs *engine;
-	int (* const *fn)(void *arg);
-	struct task_struct **tsk;
+	void (* const *fn)(struct kthread_work *);
 	int err = 0;
 
 	/*
@@ -1448,8 +1482,8 @@
 	 * tests that we load up the system maximally.
 	 */
 
-	tsk = kcalloc(nengines, sizeof(*tsk), GFP_KERNEL);
-	if (!tsk)
+	threads = kcalloc(nengines, sizeof(*threads), GFP_KERNEL);
+	if (!threads)
 		return -ENOMEM;
 
 	for (fn = func; !err && *fn; fn++) {
@@ -1466,37 +1500,44 @@
 
 		idx = 0;
 		for_each_uabi_engine(engine, i915) {
-			tsk[idx] = kthread_run(*fn, engine,
-					       "igt/parallel:%s",
-					       engine->name);
-			if (IS_ERR(tsk[idx])) {
-				err = PTR_ERR(tsk[idx]);
+			struct kthread_worker *worker;
+
+			worker = kthread_create_worker(0, "igt/parallel:%s",
+						       engine->name);
+			if (IS_ERR(worker)) {
+				err = PTR_ERR(worker);
 				break;
 			}
-			get_task_struct(tsk[idx++]);
-		}
 
-		yield(); /* start all threads before we kthread_stop() */
+			threads[idx].worker = worker;
+			threads[idx].result = 0;
+			threads[idx].engine = engine;
+
+			kthread_init_work(&threads[idx].work, *fn);
+			kthread_queue_work(worker, &threads[idx].work);
+			idx++;
+		}
 
 		idx = 0;
 		for_each_uabi_engine(engine, i915) {
 			int status;
 
-			if (IS_ERR(tsk[idx]))
+			if (!threads[idx].worker)
 				break;
 
-			status = kthread_stop(tsk[idx]);
+			kthread_flush_work(&threads[idx].work);
+			status = READ_ONCE(threads[idx].result);
 			if (status && !err)
 				err = status;
 
-			put_task_struct(tsk[idx++]);
+			kthread_destroy_worker(threads[idx++].worker);
 		}
 
 		if (igt_live_test_end(&t))
 			err = -EIO;
 	}
 
-	kfree(tsk);
+	kfree(threads);
 	return err;
 }
 
@@ -1544,7 +1585,7 @@
 	const unsigned int ncpus = num_online_cpus();
 	unsigned long num_waits, num_fences;
 	struct intel_engine_cs *engine;
-	struct task_struct **threads;
+	struct smoke_thread *threads;
 	struct igt_live_test live;
 	intel_wakeref_t wakeref;
 	struct smoketest *smoke;
@@ -1618,23 +1659,26 @@
 			 smoke[idx].max_batch, engine->name);
 
 		for (n = 0; n < ncpus; n++) {
-			struct task_struct *tsk;
+			unsigned int i = idx * ncpus + n;
+			struct kthread_worker *worker;
 
-			tsk = kthread_run(__igt_breadcrumbs_smoketest,
-					  &smoke[idx], "igt/%d.%d", idx, n);
-			if (IS_ERR(tsk)) {
-				ret = PTR_ERR(tsk);
+			worker = kthread_create_worker(0, "igt/%d.%d", idx, n);
+			if (IS_ERR(worker)) {
+				ret = PTR_ERR(worker);
 				goto out_flush;
 			}
 
-			get_task_struct(tsk);
-			threads[idx * ncpus + n] = tsk;
+			threads[i].worker = worker;
+			threads[i].t = &smoke[idx];
+
+			kthread_init_work(&threads[i].work,
+					  __igt_breadcrumbs_smoketest);
+			kthread_queue_work(worker, &threads[i].work);
 		}
 
 		idx++;
 	}
 
-	yield(); /* start all threads before we begin */
 	msleep(jiffies_to_msecs(i915_selftest.timeout_jiffies));
 
 out_flush:
@@ -1643,17 +1687,19 @@
 	num_fences = 0;
 	for_each_uabi_engine(engine, i915) {
 		for (n = 0; n < ncpus; n++) {
-			struct task_struct *tsk = threads[idx * ncpus + n];
+			unsigned int i = idx * ncpus + n;
 			int err;
 
-			if (!tsk)
+			if (!threads[i].worker)
 				continue;
 
-			err = kthread_stop(tsk);
+			WRITE_ONCE(threads[i].stop, true);
+			kthread_flush_work(&threads[i].work);
+			err = READ_ONCE(threads[i].result);
 			if (err < 0 && !ret)
 				ret = err;
 
-			put_task_struct(tsk);
+			kthread_destroy_worker(threads[i].worker);
 		}
 
 		num_waits += atomic_long_read(&smoke[idx].num_waits);
@@ -2763,9 +2809,18 @@
 	return err;
 }
 
-static int p_sync0(void *arg)
+struct p_thread {
+	struct perf_stats p;
+	struct kthread_worker *worker;
+	struct kthread_work work;
+	struct intel_engine_cs *engine;
+	int result;
+};
+
+static void p_sync0(struct kthread_work *work)
 {
-	struct perf_stats *p = arg;
+	struct p_thread *thread = container_of(work, typeof(*thread), work);
+	struct perf_stats *p = &thread->p;
 	struct intel_engine_cs *engine = p->engine;
 	struct intel_context *ce;
 	IGT_TIMEOUT(end_time);
@@ -2774,13 +2829,16 @@
 	int err = 0;
 
 	ce = intel_context_create(engine);
-	if (IS_ERR(ce))
-		return PTR_ERR(ce);
+	if (IS_ERR(ce)) {
+		thread->result = PTR_ERR(ce);
+		return;
+	}
 
 	err = intel_context_pin(ce);
 	if (err) {
 		intel_context_put(ce);
-		return err;
+		thread->result = err;
+		return;
 	}
 
 	if (intel_engine_supports_stats(engine)) {
@@ -2830,12 +2888,13 @@
 
 	intel_context_unpin(ce);
 	intel_context_put(ce);
-	return err;
+	thread->result = err;
 }
 
-static int p_sync1(void *arg)
+static void p_sync1(struct kthread_work *work)
 {
-	struct perf_stats *p = arg;
+	struct p_thread *thread = container_of(work, typeof(*thread), work);
+	struct perf_stats *p = &thread->p;
 	struct intel_engine_cs *engine = p->engine;
 	struct i915_request *prev = NULL;
 	struct intel_context *ce;
@@ -2845,13 +2904,16 @@
 	int err = 0;
 
 	ce = intel_context_create(engine);
-	if (IS_ERR(ce))
-		return PTR_ERR(ce);
+	if (IS_ERR(ce)) {
+		thread->result = PTR_ERR(ce);
+		return;
+	}
 
 	err = intel_context_pin(ce);
 	if (err) {
 		intel_context_put(ce);
-		return err;
+		thread->result = err;
+		return;
 	}
 
 	if (intel_engine_supports_stats(engine)) {
@@ -2903,12 +2965,13 @@
 
 	intel_context_unpin(ce);
 	intel_context_put(ce);
-	return err;
+	thread->result = err;
 }
 
-static int p_many(void *arg)
+static void p_many(struct kthread_work *work)
 {
-	struct perf_stats *p = arg;
+	struct p_thread *thread = container_of(work, typeof(*thread), work);
+	struct perf_stats *p = &thread->p;
 	struct intel_engine_cs *engine = p->engine;
 	struct intel_context *ce;
 	IGT_TIMEOUT(end_time);
@@ -2917,13 +2980,16 @@
 	bool busy;
 
 	ce = intel_context_create(engine);
-	if (IS_ERR(ce))
-		return PTR_ERR(ce);
+	if (IS_ERR(ce)) {
+		thread->result = PTR_ERR(ce);
+		return;
+	}
 
 	err = intel_context_pin(ce);
 	if (err) {
 		intel_context_put(ce);
-		return err;
+		thread->result = err;
+		return;
 	}
 
 	if (intel_engine_supports_stats(engine)) {
@@ -2964,26 +3030,23 @@
 
 	intel_context_unpin(ce);
 	intel_context_put(ce);
-	return err;
+	thread->result = err;
 }
 
 static int perf_parallel_engines(void *arg)
 {
 	struct drm_i915_private *i915 = arg;
-	static int (* const func[])(void *arg) = {
+	static void (* const func[])(struct kthread_work *) = {
 		p_sync0,
 		p_sync1,
 		p_many,
 		NULL,
 	};
 	const unsigned int nengines = num_uabi_engines(i915);
+	void (* const *fn)(struct kthread_work *);
 	struct intel_engine_cs *engine;
-	int (* const *fn)(void *arg);
 	struct pm_qos_request qos;
-	struct {
-		struct perf_stats p;
-		struct task_struct *tsk;
-	} *engines;
+	struct p_thread *engines;
 	int err = 0;
 
 	engines = kcalloc(nengines, sizeof(*engines), GFP_KERNEL);
@@ -3006,36 +3069,45 @@
 
 		idx = 0;
 		for_each_uabi_engine(engine, i915) {
+			struct kthread_worker *worker;
+
 			intel_engine_pm_get(engine);
 
 			memset(&engines[idx].p, 0, sizeof(engines[idx].p));
-			engines[idx].p.engine = engine;
 
-			engines[idx].tsk = kthread_run(*fn, &engines[idx].p,
-						       "igt:%s", engine->name);
-			if (IS_ERR(engines[idx].tsk)) {
-				err = PTR_ERR(engines[idx].tsk);
+			worker = kthread_create_worker(0, "igt:%s",
+						       engine->name);
+			if (IS_ERR(worker)) {
+				err = PTR_ERR(worker);
 				intel_engine_pm_put(engine);
 				break;
 			}
-			get_task_struct(engines[idx++].tsk);
-		}
+			engines[idx].worker = worker;
+			engines[idx].result = 0;
+			engines[idx].p.engine = engine;
+			engines[idx].engine = engine;
 
-		yield(); /* start all threads before we kthread_stop() */
+			kthread_init_work(&engines[idx].work, *fn);
+			kthread_queue_work(worker, &engines[idx].work);
+			idx++;
+		}
 
 		idx = 0;
 		for_each_uabi_engine(engine, i915) {
 			int status;
 
-			if (IS_ERR(engines[idx].tsk))
+			if (!engines[idx].worker)
 				break;
 
-			status = kthread_stop(engines[idx].tsk);
+			kthread_flush_work(&engines[idx].work);
+			status = READ_ONCE(engines[idx].result);
 			if (status && !err)
 				err = status;
 
 			intel_engine_pm_put(engine);
-			put_task_struct(engines[idx++].tsk);
+
+			kthread_destroy_worker(engines[idx].worker);
+			idx++;
 		}
 
 		if (igt_live_test_end(&t))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.c
@@ -16,8 +16,7 @@
 
 int intel_selftest_modify_policy(struct intel_engine_cs *engine,
 				 struct intel_selftest_saved_policy *saved,
-				 u32 modify_type)
-
+				 enum selftest_scheduler_modify modify_type)
 {
 	int err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/dcss/dcss-crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/dcss/dcss-crtc.c
@@ -206,15 +206,13 @@
 	if (crtc->irq < 0)
 		return crtc->irq;
 
-	ret = request_irq(crtc->irq, dcss_crtc_irq_handler,
-			  0, "dcss_drm", crtc);
+	ret = request_irq(crtc->irq, dcss_crtc_irq_handler, IRQF_NO_AUTOEN,
+			  "dcss_drm", crtc);
 	if (ret) {
 		dev_err(dcss->dev, "irq request failed with %d.\n", ret);
 		return ret;
 	}
 
-	disable_irq(crtc->irq);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/dcss/dcss-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/dcss/dcss-dev.c
@@ -207,6 +207,7 @@
 
 	ret = dcss_submodules_init(dcss);
 	if (ret) {
+		of_node_put(dcss->of_port);
 		dev_err(dev, "submodules initialization failed\n");
 		goto clks_err;
 	}
@@ -237,6 +238,8 @@
 		dcss_clocks_disable(dcss);
 	}
 
+	of_node_put(dcss->of_port);
+
 	pm_runtime_disable(dcss->dev);
 
 	dcss_submodules_stop(dcss);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/dcss/dcss-kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/dcss/dcss-kms.c
@@ -142,8 +142,6 @@
 
 	drm_kms_helper_poll_init(drm);
 
-	drm_bridge_connector_enable_hpd(kms->connector);
-
 	ret = drm_dev_register(drm, 0);
 	if (ret)
 		goto cleanup_crtc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/dw_hdmi-imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/dw_hdmi-imx.c
@@ -222,6 +222,7 @@
 	struct device_node *np = pdev->dev.of_node;
 	const struct of_device_id *match = of_match_node(dw_hdmi_imx_dt_ids, np);
 	struct imx_hdmi *hdmi;
+	int ret;
 
 	hdmi = devm_kzalloc(&pdev->dev, sizeof(*hdmi), GFP_KERNEL);
 	if (!hdmi)
@@ -243,10 +244,15 @@
 	hdmi->bridge = of_drm_find_bridge(np);
 	if (!hdmi->bridge) {
 		dev_err(hdmi->dev, "Unable to find bridge\n");
+		dw_hdmi_remove(hdmi->hdmi);
 		return -ENODEV;
 	}
 
-	return component_add(&pdev->dev, &dw_hdmi_imx_ops);
+	ret = component_add(&pdev->dev, &dw_hdmi_imx_ops);
+	if (ret)
+		dw_hdmi_remove(hdmi->hdmi);
+
+	return ret;
 }
 
 static int dw_hdmi_imx_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/imx-drm-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/imx-drm-core.c
@@ -81,7 +81,6 @@
 	struct drm_plane_state *old_plane_state, *new_plane_state;
 	bool plane_disabling = false;
 	int i;
-	bool fence_cookie = dma_fence_begin_signalling();
 
 	drm_atomic_helper_commit_modeset_disables(dev, state);
 
@@ -112,7 +111,6 @@
 	}
 
 	drm_atomic_helper_commit_hw_done(state);
-	dma_fence_end_signalling(fence_cookie);
 }
 
 static const struct drm_mode_config_helper_funcs imx_drm_mode_config_helpers = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/imx-ldb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/imx-ldb.c
@@ -572,6 +572,8 @@
 		edidp = of_get_property(child, "edid", &edid_len);
 		if (edidp) {
 			channel->edid = kmemdup(edidp, edid_len, GFP_KERNEL);
+			if (!channel->edid)
+				return -ENOMEM;
 		} else if (!channel->panel) {
 			/* fallback to display-timings node */
 			ret = of_get_drm_display_mode(child,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/imx-tve.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/imx-tve.c
@@ -217,8 +217,9 @@
 	return ret;
 }
 
-static int imx_tve_connector_mode_valid(struct drm_connector *connector,
-					struct drm_display_mode *mode)
+static enum drm_mode_status
+imx_tve_connector_mode_valid(struct drm_connector *connector,
+			     struct drm_display_mode *mode)
 {
 	struct imx_tve *tve = con_to_tve(connector);
 	unsigned long rate;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/ipuv3-crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/ipuv3-crtc.c
@@ -69,7 +69,7 @@
 	drm_atomic_crtc_state_for_each_plane(plane, old_crtc_state) {
 		if (plane == &ipu_crtc->plane[0]->base)
 			disable_full = true;
-		if (&ipu_crtc->plane[1] && plane == &ipu_crtc->plane[1]->base)
+		if (ipu_crtc->plane[1] && plane == &ipu_crtc->plane[1]->base)
 			disable_partial = true;
 	}
 
@@ -311,7 +311,7 @@
 		dev_warn(ipu_crtc->dev, "8-pixel align hactive %d -> %d\n",
 			 sig_cfg.mode.hactive, new_hactive);
 
-		sig_cfg.mode.hfront_porch = new_hactive - sig_cfg.mode.hactive;
+		sig_cfg.mode.hfront_porch -= new_hactive - sig_cfg.mode.hactive;
 		sig_cfg.mode.hactive = new_hactive;
 	}
 
@@ -411,14 +411,12 @@
 	}
 
 	ipu_crtc->irq = ipu_plane_irq(ipu_crtc->plane[0]);
-	ret = devm_request_irq(ipu_crtc->dev, ipu_crtc->irq, ipu_irq_handler, 0,
-			"imx_drm", ipu_crtc);
+	ret = devm_request_irq(ipu_crtc->dev, ipu_crtc->irq, ipu_irq_handler,
+			       IRQF_NO_AUTOEN, "imx_drm", ipu_crtc);
 	if (ret < 0) {
 		dev_err(ipu_crtc->dev, "irq request failed with %d.\n", ret);
 		return ret;
 	}
-	/* Only enable IRQ when we actually need it to trigger work. */
-	disable_irq(ipu_crtc->irq);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/ipuv3-plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/ipuv3-plane.c
@@ -619,6 +619,11 @@
 		break;
 	}
 
+	if (ipu_plane->dp_flow == IPU_DP_FLOW_SYNC_BG)
+		width = ipu_src_rect_width(new_state);
+	else
+		width = drm_rect_width(&new_state->src) >> 16;
+
 	eba = drm_plane_state_to_eba(new_state, 0);
 
 	/*
@@ -627,8 +632,7 @@
 	 */
 	if (ipu_state->use_pre) {
 		axi_id = ipu_chan_assign_axi_id(ipu_plane->dma);
-		ipu_prg_channel_configure(ipu_plane->ipu_ch, axi_id,
-					  ipu_src_rect_width(new_state),
+		ipu_prg_channel_configure(ipu_plane->ipu_ch, axi_id, width,
 					  drm_rect_height(&new_state->src) >> 16,
 					  fb->pitches[0], fb->format->format,
 					  fb->modifier, &eba);
@@ -683,9 +687,8 @@
 		break;
 	}
 
-	ipu_dmfc_config_wait4eot(ipu_plane->dmfc, ALIGN(drm_rect_width(dst), 8));
+	ipu_dmfc_config_wait4eot(ipu_plane->dmfc, width);
 
-	width = ipu_src_rect_width(new_state);
 	height = drm_rect_height(&new_state->src) >> 16;
 	info = drm_format_info(fb->format->format);
 	ipu_calculate_bursts(width, info->cpp[0], fb->pitches[0],
@@ -749,8 +752,7 @@
 		ipu_cpmem_set_burstsize(ipu_plane->ipu_ch, 16);
 
 		ipu_cpmem_zero(ipu_plane->alpha_ch);
-		ipu_cpmem_set_resolution(ipu_plane->alpha_ch,
-					 ipu_src_rect_width(new_state),
+		ipu_cpmem_set_resolution(ipu_plane->alpha_ch, width,
 					 drm_rect_height(&new_state->src) >> 16);
 		ipu_cpmem_set_format_passthrough(ipu_plane->alpha_ch, 8);
 		ipu_cpmem_set_high_priority(ipu_plane->alpha_ch);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/imx/parallel-display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/imx/parallel-display.c
@@ -70,13 +70,15 @@
 		int ret;
 
 		if (!mode)
-			return -EINVAL;
+			return 0;
 
 		ret = of_get_drm_display_mode(np, &imxpd->mode,
 					      &imxpd->bus_flags,
 					      OF_USE_NATIVE_MODE);
-		if (ret)
-			return ret;
+		if (ret) {
+			drm_mode_destroy(connector->dev, mode);
+			return 0;
+		}
 
 		drm_mode_copy(mode, &imxpd->mode);
 		mode->type |= DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
@@ -217,14 +219,6 @@
 	if (!imx_pd_format_supported(bus_fmt))
 		return -EINVAL;
 
-	if (bus_flags &
-	    ~(DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_DE_HIGH |
-	      DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE |
-	      DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)) {
-		dev_warn(imxpd->dev, "invalid bus_flags (%x)\n", bus_flags);
-		return -EINVAL;
-	}
-
 	bridge_state->output_bus_cfg.flags = bus_flags;
 	bridge_state->input_bus_cfg.flags = bus_flags;
 	imx_crtc_state->bus_flags = bus_flags;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
@@ -1326,7 +1326,11 @@
 			return err;
 	}
 
-	return platform_driver_register(&ingenic_drm_driver);
+	err = platform_driver_register(&ingenic_drm_driver);
+	if (IS_ENABLED(CONFIG_DRM_INGENIC_IPU) && err)
+		platform_driver_unregister(ingenic_ipu_driver_ptr);
+
+	return err;
 }
 module_init(ingenic_drm_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/kmb/kmb_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/kmb/kmb_plane.c
@@ -158,12 +158,6 @@
 	case LAYER_1:
 		kmb->plane_status[plane_id].ctrl = LCD_CTRL_VL2_ENABLE;
 		break;
-	case LAYER_2:
-		kmb->plane_status[plane_id].ctrl = LCD_CTRL_GL1_ENABLE;
-		break;
-	case LAYER_3:
-		kmb->plane_status[plane_id].ctrl = LCD_CTRL_GL2_ENABLE;
-		break;
 	}
 
 	kmb->plane_status[plane_id].disable = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_bcast.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_bcast.c
@@ -43,6 +43,18 @@
 
 }
 
+int lima_bcast_mask_irq(struct lima_ip *ip)
+{
+	bcast_write(LIMA_BCAST_BROADCAST_MASK, 0);
+	bcast_write(LIMA_BCAST_INTERRUPT_MASK, 0);
+	return 0;
+}
+
+int lima_bcast_reset(struct lima_ip *ip)
+{
+	return lima_bcast_hw_init(ip);
+}
+
 int lima_bcast_init(struct lima_ip *ip)
 {
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_bcast.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_bcast.h
@@ -13,4 +13,7 @@
 
 void lima_bcast_enable(struct lima_device *dev, int num_pp);
 
+int lima_bcast_mask_irq(struct lima_ip *ip);
+int lima_bcast_reset(struct lima_ip *ip);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_device.c
@@ -357,6 +357,7 @@
 	int err, i;
 
 	dma_set_coherent_mask(ldev->dev, DMA_BIT_MASK(32));
+	dma_set_max_seg_size(ldev->dev, UINT_MAX);
 
 	err = lima_clk_init(ldev);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_drv.c
@@ -392,8 +392,10 @@
 
 	/* Allocate and initialize the DRM device. */
 	ddev = drm_dev_alloc(&lima_drm_driver, &pdev->dev);
-	if (IS_ERR(ddev))
-		return PTR_ERR(ddev);
+	if (IS_ERR(ddev)) {
+		err = PTR_ERR(ddev);
+		goto err_out0;
+	}
 
 	ddev->dev_private = ldev;
 	ldev->ddev = ddev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_gem.c
@@ -74,29 +74,34 @@
 	} else {
 		bo->base.sgt = kmalloc(sizeof(*bo->base.sgt), GFP_KERNEL);
 		if (!bo->base.sgt) {
-			sg_free_table(&sgt);
-			return -ENOMEM;
+			ret = -ENOMEM;
+			goto err_out0;
 		}
 	}
 
 	ret = dma_map_sgtable(dev, &sgt, DMA_BIDIRECTIONAL, 0);
-	if (ret) {
-		sg_free_table(&sgt);
-		kfree(bo->base.sgt);
-		bo->base.sgt = NULL;
-		return ret;
-	}
+	if (ret)
+		goto err_out1;
 
 	*bo->base.sgt = sgt;
 
 	if (vm) {
 		ret = lima_vm_map_bo(vm, bo, old_size >> PAGE_SHIFT);
 		if (ret)
-			return ret;
+			goto err_out2;
 	}
 
 	bo->heap_size = new_size;
 	return 0;
+
+err_out2:
+	dma_unmap_sgtable(dev, &sgt, DMA_BIDIRECTIONAL, 0);
+err_out1:
+	kfree(bo->base.sgt);
+	bo->base.sgt = NULL;
+err_out0:
+	sg_free_table(&sgt);
+	return ret;
 }
 
 int lima_gem_create_handle(struct drm_device *dev, struct drm_file *file,
@@ -127,7 +132,7 @@
 		if (err)
 			goto out;
 	} else {
-		struct sg_table *sgt = drm_gem_shmem_get_pages_sgt(obj);
+		struct sg_table *sgt = drm_gem_shmem_get_pages_sgt(shmem);
 
 		if (IS_ERR(sgt)) {
 			err = PTR_ERR(sgt);
@@ -151,7 +156,7 @@
 	if (!list_empty(&bo->va))
 		dev_err(obj->dev->dev, "lima gem free bo still has va\n");
 
-	drm_gem_shmem_free_object(obj);
+	drm_gem_shmem_free(&bo->base);
 }
 
 static int lima_gem_object_open(struct drm_gem_object *obj, struct drm_file *file)
@@ -179,7 +184,7 @@
 	if (bo->heap_size)
 		return -EINVAL;
 
-	return drm_gem_shmem_pin(obj);
+	return drm_gem_shmem_pin(&bo->base);
 }
 
 static int lima_gem_vmap(struct drm_gem_object *obj, struct dma_buf_map *map)
@@ -189,7 +194,7 @@
 	if (bo->heap_size)
 		return -EINVAL;
 
-	return drm_gem_shmem_vmap(obj, map);
+	return drm_gem_shmem_vmap(&bo->base, map);
 }
 
 static int lima_gem_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
@@ -199,19 +204,19 @@
 	if (bo->heap_size)
 		return -EINVAL;
 
-	return drm_gem_shmem_mmap(obj, vma);
+	return drm_gem_shmem_mmap(&bo->base, vma);
 }
 
 static const struct drm_gem_object_funcs lima_gem_funcs = {
 	.free = lima_gem_free_object,
 	.open = lima_gem_object_open,
 	.close = lima_gem_object_close,
-	.print_info = drm_gem_shmem_print_info,
+	.print_info = drm_gem_shmem_object_print_info,
 	.pin = lima_gem_pin,
-	.unpin = drm_gem_shmem_unpin,
-	.get_sg_table = drm_gem_shmem_get_sg_table,
+	.unpin = drm_gem_shmem_object_unpin,
+	.get_sg_table = drm_gem_shmem_object_get_sg_table,
 	.vmap = lima_gem_vmap,
-	.vunmap = drm_gem_shmem_vunmap,
+	.vunmap = drm_gem_shmem_object_vunmap,
 	.mmap = lima_gem_mmap,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_gp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_gp.c
@@ -166,6 +166,11 @@
 	gp_write(LIMA_GP_CMD, cmd);
 }
 
+static int lima_gp_bus_stop_poll(struct lima_ip *ip)
+{
+	return !!(gp_read(LIMA_GP_STATUS) & LIMA_GP_STATUS_BUS_STOPPED);
+}
+
 static int lima_gp_hard_reset_poll(struct lima_ip *ip)
 {
 	gp_write(LIMA_GP_PERF_CNT_0_LIMIT, 0xC01A0000);
@@ -179,6 +184,13 @@
 
 	gp_write(LIMA_GP_PERF_CNT_0_LIMIT, 0xC0FFE000);
 	gp_write(LIMA_GP_INT_MASK, 0);
+
+	gp_write(LIMA_GP_CMD, LIMA_GP_CMD_STOP_BUS);
+	ret = lima_poll_timeout(ip, lima_gp_bus_stop_poll, 10, 100);
+	if (ret) {
+		dev_err(dev->dev, "%s bus stop timeout\n", lima_ip_name(ip));
+		return ret;
+	}
 	gp_write(LIMA_GP_CMD, LIMA_GP_CMD_RESET);
 	ret = lima_poll_timeout(ip, lima_gp_hard_reset_poll, 10, 100);
 	if (ret) {
@@ -212,6 +224,13 @@
 	lima_sched_pipe_task_done(pipe);
 }
 
+static void lima_gp_task_mask_irq(struct lima_sched_pipe *pipe)
+{
+	struct lima_ip *ip = pipe->processor[0];
+
+	gp_write(LIMA_GP_INT_MASK, 0);
+}
+
 static int lima_gp_task_recover(struct lima_sched_pipe *pipe)
 {
 	struct lima_ip *ip = pipe->processor[0];
@@ -317,7 +336,9 @@
 
 void lima_gp_fini(struct lima_ip *ip)
 {
+	struct lima_device *dev = ip->dev;
 
+	devm_free_irq(dev->dev, ip->irq, ip);
 }
 
 int lima_gp_pipe_init(struct lima_device *dev)
@@ -344,6 +365,7 @@
 	pipe->task_error = lima_gp_task_error;
 	pipe->task_mmu_error = lima_gp_task_mmu_error;
 	pipe->task_recover = lima_gp_task_recover;
+	pipe->task_mask_irq = lima_gp_task_mask_irq;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_mmu.c
@@ -118,7 +118,12 @@
 
 void lima_mmu_fini(struct lima_ip *ip)
 {
+	struct lima_device *dev = ip->dev;
 
+	if (ip->id == lima_ip_ppmmu_bcast)
+		return;
+
+	devm_free_irq(dev->dev, ip->irq, ip);
 }
 
 void lima_mmu_flush_tlb(struct lima_ip *ip)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_pp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_pp.c
@@ -266,7 +266,9 @@
 
 void lima_pp_fini(struct lima_ip *ip)
 {
+	struct lima_device *dev = ip->dev;
 
+	devm_free_irq(dev->dev, ip->irq, ip);
 }
 
 int lima_pp_bcast_resume(struct lima_ip *ip)
@@ -299,7 +301,9 @@
 
 void lima_pp_bcast_fini(struct lima_ip *ip)
 {
+	struct lima_device *dev = ip->dev;
 
+	devm_free_irq(dev->dev, ip->irq, ip);
 }
 
 static int lima_pp_task_validate(struct lima_sched_pipe *pipe,
@@ -408,6 +412,9 @@
 
 		lima_pp_hard_reset(ip);
 	}
+
+	if (pipe->bcast_processor)
+		lima_bcast_reset(pipe->bcast_processor);
 }
 
 static void lima_pp_task_mmu_error(struct lima_sched_pipe *pipe)
@@ -416,6 +423,20 @@
 		lima_sched_pipe_task_done(pipe);
 }
 
+static void lima_pp_task_mask_irq(struct lima_sched_pipe *pipe)
+{
+	int i;
+
+	for (i = 0; i < pipe->num_processor; i++) {
+		struct lima_ip *ip = pipe->processor[i];
+
+		pp_write(LIMA_PP_INT_MASK, 0);
+	}
+
+	if (pipe->bcast_processor)
+		lima_bcast_mask_irq(pipe->bcast_processor);
+}
+
 static struct kmem_cache *lima_pp_task_slab;
 static int lima_pp_task_slab_refcnt;
 
@@ -447,6 +468,7 @@
 	pipe->task_fini = lima_pp_task_fini;
 	pipe->task_error = lima_pp_task_error;
 	pipe->task_mmu_error = lima_pp_task_mmu_error;
+	pipe->task_mask_irq = lima_pp_task_mask_irq;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_sched.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_sched.c
@@ -390,7 +390,7 @@
 		} else {
 			buffer_chunk->size = lima_bo_size(bo);
 
-			ret = drm_gem_shmem_vmap(&bo->base.base, &map);
+			ret = drm_gem_shmem_vmap(&bo->base, &map);
 			if (ret) {
 				kvfree(et);
 				goto out;
@@ -398,7 +398,7 @@
 
 			memcpy(buffer_chunk + 1, map.vaddr, buffer_chunk->size);
 
-			drm_gem_shmem_vunmap(&bo->base.base, &map);
+			drm_gem_shmem_vunmap(&bo->base, &map);
 		}
 
 		buffer_chunk = (void *)(buffer_chunk + 1) + buffer_chunk->size;
@@ -421,6 +421,13 @@
 	struct lima_sched_task *task = to_lima_task(job);
 	struct lima_device *ldev = pipe->ldev;
 
+	/*
+	 * The task might still finish while this timeout handler runs.
+	 * To prevent a race condition on its completion, mask all irqs
+	 * on the running core until the next hard reset completes.
+	 */
+	pipe->task_mask_irq(pipe);
+
 	if (!pipe->error)
 		DRM_ERROR("lima job timeout\n");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/lima/lima_sched.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/lima/lima_sched.h
@@ -83,6 +83,7 @@
 	void (*task_error)(struct lima_sched_pipe *pipe);
 	void (*task_mmu_error)(struct lima_sched_pipe *pipe);
 	int (*task_recover)(struct lima_sched_pipe *pipe);
+	void (*task_mask_irq)(struct lima_sched_pipe *pipe);
 
 	struct work_struct recover_work;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mcde/mcde_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mcde/mcde_drv.c
@@ -475,6 +475,7 @@
 	},
 	{},
 };
+MODULE_DEVICE_TABLE(of, mcde_of_match);
 
 static struct platform_driver mcde_driver = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mcde/mcde_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mcde/mcde_dsi.c
@@ -1111,6 +1111,7 @@
 			bridge = of_drm_find_bridge(child);
 			if (!bridge) {
 				dev_err(dev, "failed to find bridge\n");
+				of_node_put(child);
 				return -EINVAL;
 			}
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_cec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_cec.c
@@ -85,7 +85,7 @@
 	u32 tmp = readl(cec->regs + offset) & ~mask;
 
 	tmp |= val & mask;
-	writel(val, cec->regs + offset);
+	writel(tmp, cec->regs + offset);
 }
 
 void mtk_cec_set_hpd_event(struct device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_disp_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_disp_drv.h
@@ -76,9 +76,11 @@
 void mtk_ovl_start(struct device *dev);
 void mtk_ovl_stop(struct device *dev);
 unsigned int mtk_ovl_supported_rotations(struct device *dev);
-void mtk_ovl_enable_vblank(struct device *dev,
-			   void (*vblank_cb)(void *),
-			   void *vblank_cb_data);
+void mtk_ovl_register_vblank_cb(struct device *dev,
+				void (*vblank_cb)(void *),
+				void *vblank_cb_data);
+void mtk_ovl_unregister_vblank_cb(struct device *dev);
+void mtk_ovl_enable_vblank(struct device *dev);
 void mtk_ovl_disable_vblank(struct device *dev);
 
 void mtk_rdma_bypass_shadow(struct device *dev);
@@ -93,9 +95,11 @@
 			   struct cmdq_pkt *cmdq_pkt);
 void mtk_rdma_start(struct device *dev);
 void mtk_rdma_stop(struct device *dev);
-void mtk_rdma_enable_vblank(struct device *dev,
-			    void (*vblank_cb)(void *),
-			    void *vblank_cb_data);
+void mtk_rdma_register_vblank_cb(struct device *dev,
+				 void (*vblank_cb)(void *),
+				 void *vblank_cb_data);
+void mtk_rdma_unregister_vblank_cb(struct device *dev);
+void mtk_rdma_enable_vblank(struct device *dev);
 void mtk_rdma_disable_vblank(struct device *dev);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_disp_ovl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_disp_ovl.c
@@ -96,14 +96,28 @@
 	return IRQ_HANDLED;
 }
 
-void mtk_ovl_enable_vblank(struct device *dev,
-			   void (*vblank_cb)(void *),
-			   void *vblank_cb_data)
+void mtk_ovl_register_vblank_cb(struct device *dev,
+				void (*vblank_cb)(void *),
+				void *vblank_cb_data)
 {
 	struct mtk_disp_ovl *ovl = dev_get_drvdata(dev);
 
 	ovl->vblank_cb = vblank_cb;
 	ovl->vblank_cb_data = vblank_cb_data;
+}
+
+void mtk_ovl_unregister_vblank_cb(struct device *dev)
+{
+	struct mtk_disp_ovl *ovl = dev_get_drvdata(dev);
+
+	ovl->vblank_cb = NULL;
+	ovl->vblank_cb_data = NULL;
+}
+
+void mtk_ovl_enable_vblank(struct device *dev)
+{
+	struct mtk_disp_ovl *ovl = dev_get_drvdata(dev);
+
 	writel(0x0, ovl->regs + DISP_REG_OVL_INTSTA);
 	writel_relaxed(OVL_FME_CPL_INT, ovl->regs + DISP_REG_OVL_INTEN);
 }
@@ -112,8 +126,6 @@
 {
 	struct mtk_disp_ovl *ovl = dev_get_drvdata(dev);
 
-	ovl->vblank_cb = NULL;
-	ovl->vblank_cb_data = NULL;
 	writel_relaxed(0x0, ovl->regs + DISP_REG_OVL_INTEN);
 }
 
@@ -192,27 +204,20 @@
 			struct mtk_plane_state *mtk_state)
 {
 	struct drm_plane_state *state = &mtk_state->base;
-	unsigned int rotation = 0;
-
-	rotation = drm_rotation_simplify(state->rotation,
-					 DRM_MODE_ROTATE_0 |
-					 DRM_MODE_REFLECT_X |
-					 DRM_MODE_REFLECT_Y);
-	rotation &= ~DRM_MODE_ROTATE_0;
 
-	/* We can only do reflection, not rotation */
-	if ((rotation & DRM_MODE_ROTATE_MASK) != 0)
+	/* check if any unsupported rotation is set */
+	if (state->rotation & ~mtk_ovl_supported_rotations(dev))
 		return -EINVAL;
 
 	/*
 	 * TODO: Rotating/reflecting YUV buffers is not supported at this time.
 	 *	 Only RGB[AX] variants are supported.
+	 *	 Since DRM_MODE_ROTATE_0 means "no rotation", we should not
+	 *	 reject layers with this property.
 	 */
-	if (state->fb->format->is_yuv && rotation != 0)
+	if (state->fb->format->is_yuv && (state->rotation & ~DRM_MODE_ROTATE_0))
 		return -EINVAL;
 
-	state->rotation = rotation;
-
 	return 0;
 }
 
@@ -297,6 +302,7 @@
 	unsigned int addr = pending->addr;
 	unsigned int pitch = pending->pitch & 0xffff;
 	unsigned int fmt = pending->format;
+	unsigned int rotation = pending->rotation;
 	unsigned int offset = (pending->y << 16) | pending->x;
 	unsigned int src_size = (pending->height << 16) | pending->width;
 	unsigned int con;
@@ -310,12 +316,19 @@
 	if (state->base.fb && state->base.fb->format->has_alpha)
 		con |= OVL_CON_AEN | OVL_CON_ALPHA;
 
-	if (pending->rotation & DRM_MODE_REFLECT_Y) {
+	/*
+	 * Treat rotate 180 as flip x + flip y, and XOR the original rotation value
+	 * to flip x + flip y to support both in the same time.
+	 */
+	if (rotation & DRM_MODE_ROTATE_180)
+		rotation ^= DRM_MODE_REFLECT_X | DRM_MODE_REFLECT_Y;
+
+	if (rotation & DRM_MODE_REFLECT_Y) {
 		con |= OVL_CON_VIRT_FLIP;
 		addr += (pending->height - 1) * pending->pitch;
 	}
 
-	if (pending->rotation & DRM_MODE_REFLECT_X) {
+	if (rotation & DRM_MODE_REFLECT_X) {
 		con |= OVL_CON_HORZ_FLIP;
 		addr += pending->pitch - 1;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_disp_rdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_disp_rdma.c
@@ -94,24 +94,32 @@
 	writel(tmp, rdma->regs + reg);
 }
 
-void mtk_rdma_enable_vblank(struct device *dev,
-			    void (*vblank_cb)(void *),
-			    void *vblank_cb_data)
+void mtk_rdma_register_vblank_cb(struct device *dev,
+				 void (*vblank_cb)(void *),
+				 void *vblank_cb_data)
 {
 	struct mtk_disp_rdma *rdma = dev_get_drvdata(dev);
 
 	rdma->vblank_cb = vblank_cb;
 	rdma->vblank_cb_data = vblank_cb_data;
-	rdma_update_bits(dev, DISP_REG_RDMA_INT_ENABLE, RDMA_FRAME_END_INT,
-			 RDMA_FRAME_END_INT);
 }
 
-void mtk_rdma_disable_vblank(struct device *dev)
+void mtk_rdma_unregister_vblank_cb(struct device *dev)
 {
 	struct mtk_disp_rdma *rdma = dev_get_drvdata(dev);
 
 	rdma->vblank_cb = NULL;
 	rdma->vblank_cb_data = NULL;
+}
+
+void mtk_rdma_enable_vblank(struct device *dev)
+{
+	rdma_update_bits(dev, DISP_REG_RDMA_INT_ENABLE, RDMA_FRAME_END_INT,
+			 RDMA_FRAME_END_INT);
+}
+
+void mtk_rdma_disable_vblank(struct device *dev)
+{
 	rdma_update_bits(dev, DISP_REG_RDMA_INT_ENABLE, RDMA_FRAME_END_INT, 0);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -54,13 +54,7 @@
 };
 
 enum mtk_dpi_out_color_format {
-	MTK_DPI_COLOR_FORMAT_RGB,
-	MTK_DPI_COLOR_FORMAT_RGB_FULL,
-	MTK_DPI_COLOR_FORMAT_YCBCR_444,
-	MTK_DPI_COLOR_FORMAT_YCBCR_422,
-	MTK_DPI_COLOR_FORMAT_XV_YCC,
-	MTK_DPI_COLOR_FORMAT_YCBCR_444_FULL,
-	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
+	MTK_DPI_COLOR_FORMAT_RGB
 };
 
 struct mtk_dpi {
@@ -364,24 +358,11 @@
 static void mtk_dpi_config_color_format(struct mtk_dpi *dpi,
 					enum mtk_dpi_out_color_format format)
 {
-	if ((format == MTK_DPI_COLOR_FORMAT_YCBCR_444) ||
-	    (format == MTK_DPI_COLOR_FORMAT_YCBCR_444_FULL)) {
-		mtk_dpi_config_yuv422_enable(dpi, false);
-		mtk_dpi_config_csc_enable(dpi, true);
-		mtk_dpi_config_swap_input(dpi, false);
-		mtk_dpi_config_channel_swap(dpi, MTK_DPI_OUT_CHANNEL_SWAP_BGR);
-	} else if ((format == MTK_DPI_COLOR_FORMAT_YCBCR_422) ||
-		   (format == MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL)) {
-		mtk_dpi_config_yuv422_enable(dpi, true);
-		mtk_dpi_config_csc_enable(dpi, true);
-		mtk_dpi_config_swap_input(dpi, true);
-		mtk_dpi_config_channel_swap(dpi, MTK_DPI_OUT_CHANNEL_SWAP_RGB);
-	} else {
-		mtk_dpi_config_yuv422_enable(dpi, false);
-		mtk_dpi_config_csc_enable(dpi, false);
-		mtk_dpi_config_swap_input(dpi, false);
-		mtk_dpi_config_channel_swap(dpi, MTK_DPI_OUT_CHANNEL_SWAP_RGB);
-	}
+	/* only support RGB888 */
+	mtk_dpi_config_yuv422_enable(dpi, false);
+	mtk_dpi_config_csc_enable(dpi, false);
+	mtk_dpi_config_swap_input(dpi, false);
+	mtk_dpi_config_channel_swap(dpi, MTK_DPI_OUT_CHANNEL_SWAP_RGB);
 }
 
 static void mtk_dpi_dual_edge(struct mtk_dpi *dpi)
@@ -406,9 +387,6 @@
 	if (--dpi->refcount != 0)
 		return;
 
-	if (dpi->pinctrl && dpi->pins_gpio)
-		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
-
 	mtk_dpi_disable(dpi);
 	clk_disable_unprepare(dpi->pixel_clk);
 	clk_disable_unprepare(dpi->engine_clk);
@@ -433,10 +411,6 @@
 		goto err_pixel;
 	}
 
-	if (dpi->pinctrl && dpi->pins_dpi)
-		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
-
-	mtk_dpi_enable(dpi);
 	return 0;
 
 err_pixel:
@@ -650,14 +624,21 @@
 	struct mtk_dpi *dpi = bridge_to_dpi(bridge);
 
 	mtk_dpi_power_off(dpi);
+
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
 }
 
 static void mtk_dpi_bridge_enable(struct drm_bridge *bridge)
 {
 	struct mtk_dpi *dpi = bridge_to_dpi(bridge);
 
+	if (dpi->pinctrl && dpi->pins_dpi)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
+
 	mtk_dpi_power_on(dpi);
 	mtk_dpi_set_display_mode(dpi, &dpi->mode);
+	mtk_dpi_enable(dpi);
 }
 
 static enum drm_mode_status
@@ -819,8 +800,8 @@
 	.cal_factor = mt8183_calculate_factor,
 	.reg_h_fre_con = 0xe0,
 	.max_clock_khz = 150000,
-	.output_fmts = mt8173_output_fmts,
-	.num_output_fmts = ARRAY_SIZE(mt8173_output_fmts),
+	.output_fmts = mt8183_output_fmts,
+	.num_output_fmts = ARRAY_SIZE(mt8183_output_fmts),
 };
 
 static int mtk_dpi_probe(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_drm_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_drm_crtc.c
@@ -4,6 +4,8 @@
  */
 
 #include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/mailbox_controller.h>
 #include <linux/pm_runtime.h>
 #include <linux/soc/mediatek/mtk-cmdq.h>
 #include <linux/soc/mediatek/mtk-mmsys.h>
@@ -50,8 +52,10 @@
 	bool				pending_async_planes;
 
 #if IS_REACHABLE(CONFIG_MTK_CMDQ)
-	struct cmdq_client		*cmdq_client;
+	struct cmdq_client		cmdq_client;
+	struct cmdq_pkt			cmdq_handle;
 	u32				cmdq_event;
+	u32				cmdq_vblank_cnt;
 #endif
 
 	struct device			*mmsys_dev;
@@ -88,11 +92,13 @@
 	struct drm_crtc *crtc = &mtk_crtc->base;
 	unsigned long flags;
 
-	spin_lock_irqsave(&crtc->dev->event_lock, flags);
-	drm_crtc_send_vblank_event(crtc, mtk_crtc->event);
-	drm_crtc_vblank_put(crtc);
-	mtk_crtc->event = NULL;
-	spin_unlock_irqrestore(&crtc->dev->event_lock, flags);
+	if (mtk_crtc->event) {
+		spin_lock_irqsave(&crtc->dev->event_lock, flags);
+		drm_crtc_send_vblank_event(crtc, mtk_crtc->event);
+		drm_crtc_vblank_put(crtc);
+		mtk_crtc->event = NULL;
+		spin_unlock_irqrestore(&crtc->dev->event_lock, flags);
+	}
 }
 
 static void mtk_drm_finish_page_flip(struct mtk_drm_crtc *mtk_crtc)
@@ -104,11 +110,60 @@
 	}
 }
 
+#if IS_REACHABLE(CONFIG_MTK_CMDQ)
+static int mtk_drm_cmdq_pkt_create(struct cmdq_client *client, struct cmdq_pkt *pkt,
+				   size_t size)
+{
+	struct device *dev;
+	dma_addr_t dma_addr;
+
+	pkt->va_base = kzalloc(size, GFP_KERNEL);
+	if (!pkt->va_base)
+		return -ENOMEM;
+
+	pkt->buf_size = size;
+	pkt->cl = (void *)client;
+
+	dev = client->chan->mbox->dev;
+	dma_addr = dma_map_single(dev, pkt->va_base, pkt->buf_size,
+				  DMA_TO_DEVICE);
+	if (dma_mapping_error(dev, dma_addr)) {
+		dev_err(dev, "dma map failed, size=%u\n", (u32)(u64)size);
+		kfree(pkt->va_base);
+		return -ENOMEM;
+	}
+
+	pkt->pa_base = dma_addr;
+
+	return 0;
+}
+
+static void mtk_drm_cmdq_pkt_destroy(struct cmdq_pkt *pkt)
+{
+	struct cmdq_client *client = (struct cmdq_client *)pkt->cl;
+
+	dma_unmap_single(client->chan->mbox->dev, pkt->pa_base, pkt->buf_size,
+			 DMA_TO_DEVICE);
+	kfree(pkt->va_base);
+}
+#endif
+
 static void mtk_drm_crtc_destroy(struct drm_crtc *crtc)
 {
 	struct mtk_drm_crtc *mtk_crtc = to_mtk_crtc(crtc);
+	int i;
 
 	mtk_mutex_put(mtk_crtc->mutex);
+#if IS_REACHABLE(CONFIG_MTK_CMDQ)
+	mtk_drm_cmdq_pkt_destroy(&mtk_crtc->cmdq_handle);
+#endif
+
+	for (i = 0; i < mtk_crtc->ddp_comp_nr; i++) {
+		struct mtk_ddp_comp *comp;
+
+		comp = mtk_crtc->ddp_comp[i];
+		mtk_ddp_comp_unregister_vblank_cb(comp);
+	}
 
 	drm_crtc_cleanup(crtc);
 }
@@ -222,9 +277,12 @@
 }
 
 #if IS_REACHABLE(CONFIG_MTK_CMDQ)
-static void ddp_cmdq_cb(struct cmdq_cb_data data)
+static void ddp_cmdq_cb(struct mbox_client *cl, void *mssg)
 {
-	cmdq_pkt_destroy(data.data);
+	struct cmdq_client *cmdq_cl = container_of(cl, struct cmdq_client, client);
+	struct mtk_drm_crtc *mtk_crtc = container_of(cmdq_cl, struct mtk_drm_crtc, cmdq_client);
+
+	mtk_crtc->cmdq_vblank_cnt = 0;
 }
 #endif
 
@@ -306,6 +364,9 @@
 		unsigned int local_layer;
 
 		plane_state = to_mtk_plane_state(plane->state);
+
+		/* should not enable layer before crtc enabled */
+		plane_state->pending.enable = false;
 		comp = mtk_drm_ddp_comp_for_plane(crtc, plane, &local_layer);
 		if (comp)
 			mtk_ddp_comp_layer_config(comp, local_layer,
@@ -325,6 +386,7 @@
 {
 	struct drm_device *drm = mtk_crtc->base.dev;
 	struct drm_crtc *crtc = &mtk_crtc->base;
+	unsigned long flags;
 	int i;
 
 	for (i = 0; i < mtk_crtc->ddp_comp_nr; i++) {
@@ -351,10 +413,10 @@
 	pm_runtime_put(drm->dev);
 
 	if (crtc->state->event && !crtc->state->active) {
-		spin_lock_irq(&crtc->dev->event_lock);
+		spin_lock_irqsave(&crtc->dev->event_lock, flags);
 		drm_crtc_send_vblank_event(crtc, crtc->state->event);
 		crtc->state->event = NULL;
-		spin_unlock_irq(&crtc->dev->event_lock);
+		spin_unlock_irqrestore(&crtc->dev->event_lock, flags);
 	}
 }
 
@@ -430,7 +492,7 @@
 				       bool needs_vblank)
 {
 #if IS_REACHABLE(CONFIG_MTK_CMDQ)
-	struct cmdq_pkt *cmdq_handle;
+	struct cmdq_pkt *cmdq_handle = &mtk_crtc->cmdq_handle;
 #endif
 	struct drm_crtc *crtc = &mtk_crtc->base;
 	struct mtk_drm_private *priv = crtc->dev->dev_private;
@@ -468,14 +530,28 @@
 		mtk_mutex_release(mtk_crtc->mutex);
 	}
 #if IS_REACHABLE(CONFIG_MTK_CMDQ)
-	if (mtk_crtc->cmdq_client) {
-		mbox_flush(mtk_crtc->cmdq_client->chan, 2000);
-		cmdq_handle = cmdq_pkt_create(mtk_crtc->cmdq_client, PAGE_SIZE);
+	if (mtk_crtc->cmdq_client.chan) {
+		mbox_flush(mtk_crtc->cmdq_client.chan, 2000);
+		cmdq_handle->cmd_buf_size = 0;
 		cmdq_pkt_clear_event(cmdq_handle, mtk_crtc->cmdq_event);
 		cmdq_pkt_wfe(cmdq_handle, mtk_crtc->cmdq_event, false);
 		mtk_crtc_ddp_config(crtc, cmdq_handle);
 		cmdq_pkt_finalize(cmdq_handle);
-		cmdq_pkt_flush_async(cmdq_handle, ddp_cmdq_cb, cmdq_handle);
+		dma_sync_single_for_device(mtk_crtc->cmdq_client.chan->mbox->dev,
+					   cmdq_handle->pa_base,
+					   cmdq_handle->cmd_buf_size,
+					   DMA_TO_DEVICE);
+		/*
+		 * CMDQ command should execute in next 3 vblank.
+		 * One vblank interrupt before send message (occasionally)
+		 * and one vblank interrupt after cmdq done,
+		 * so it's timeout after 3 vblank interrupt.
+		 * If it fail to execute in next 3 vblank, timeout happen.
+		 */
+		mtk_crtc->cmdq_vblank_cnt = 3;
+
+		mbox_send_message(mtk_crtc->cmdq_client.chan, cmdq_handle);
+		mbox_client_txdone(mtk_crtc->cmdq_client.chan, 0);
 	}
 #endif
 	mtk_crtc->config_updating = false;
@@ -489,12 +565,15 @@
 	struct mtk_drm_private *priv = crtc->dev->dev_private;
 
 #if IS_REACHABLE(CONFIG_MTK_CMDQ)
-	if (!priv->data->shadow_register && !mtk_crtc->cmdq_client)
+	if (!priv->data->shadow_register && !mtk_crtc->cmdq_client.chan)
+		mtk_crtc_ddp_config(crtc, NULL);
+	else if (mtk_crtc->cmdq_vblank_cnt > 0 && --mtk_crtc->cmdq_vblank_cnt == 0)
+		DRM_ERROR("mtk_crtc %d CMDQ execute command timeout!\n",
+			  drm_crtc_index(&mtk_crtc->base));
 #else
 	if (!priv->data->shadow_register)
-#endif
 		mtk_crtc_ddp_config(crtc, NULL);
-
+#endif
 	mtk_drm_finish_page_flip(mtk_crtc);
 }
 
@@ -503,7 +582,7 @@
 	struct mtk_drm_crtc *mtk_crtc = to_mtk_crtc(crtc);
 	struct mtk_ddp_comp *comp = mtk_crtc->ddp_comp[0];
 
-	mtk_ddp_comp_enable_vblank(comp, mtk_crtc_ddp_irq, &mtk_crtc->base);
+	mtk_ddp_comp_enable_vblank(comp);
 
 	return 0;
 }
@@ -604,6 +683,7 @@
 									  crtc);
 	struct mtk_crtc_state *mtk_crtc_state = to_mtk_crtc_state(crtc_state);
 	struct mtk_drm_crtc *mtk_crtc = to_mtk_crtc(crtc);
+	unsigned long flags;
 
 	if (mtk_crtc->event && mtk_crtc_state->base.event)
 		DRM_ERROR("new event while there is still a pending event\n");
@@ -611,7 +691,11 @@
 	if (mtk_crtc_state->base.event) {
 		mtk_crtc_state->base.event->pipe = drm_crtc_index(crtc);
 		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
+
+		spin_lock_irqsave(&crtc->dev->event_lock, flags);
 		mtk_crtc->event = mtk_crtc_state->base.event;
+		spin_unlock_irqrestore(&crtc->dev->event_lock, flags);
+
 		mtk_crtc_state->base.event = NULL;
 	}
 }
@@ -803,6 +887,9 @@
 			if (comp->funcs->ctm_set)
 				has_ctm = true;
 		}
+
+		mtk_ddp_comp_register_vblank_cb(comp, mtk_crtc_ddp_irq,
+						&mtk_crtc->base);
 	}
 
 	for (i = 0; i < mtk_crtc->ddp_comp_nr; i++)
@@ -810,6 +897,8 @@
 
 	mtk_crtc->planes = devm_kcalloc(dev, num_comp_planes,
 					sizeof(struct drm_plane), GFP_KERNEL);
+	if (!mtk_crtc->planes)
+		return -ENOMEM;
 
 	for (i = 0; i < mtk_crtc->ddp_comp_nr; i++) {
 		ret = mtk_drm_crtc_init_comp_planes(drm_dev, mtk_crtc, i,
@@ -829,16 +918,20 @@
 	mutex_init(&mtk_crtc->hw_lock);
 
 #if IS_REACHABLE(CONFIG_MTK_CMDQ)
-	mtk_crtc->cmdq_client =
-			cmdq_mbox_create(mtk_crtc->mmsys_dev,
-					 drm_crtc_index(&mtk_crtc->base));
-	if (IS_ERR(mtk_crtc->cmdq_client)) {
+	mtk_crtc->cmdq_client.client.dev = mtk_crtc->mmsys_dev;
+	mtk_crtc->cmdq_client.client.tx_block = false;
+	mtk_crtc->cmdq_client.client.knows_txdone = true;
+	mtk_crtc->cmdq_client.client.rx_callback = ddp_cmdq_cb;
+	mtk_crtc->cmdq_client.chan =
+			mbox_request_channel(&mtk_crtc->cmdq_client.client,
+					     drm_crtc_index(&mtk_crtc->base));
+	if (IS_ERR(mtk_crtc->cmdq_client.chan)) {
 		dev_dbg(dev, "mtk_crtc %d failed to create mailbox client, writing register by CPU now\n",
 			drm_crtc_index(&mtk_crtc->base));
-		mtk_crtc->cmdq_client = NULL;
+		mtk_crtc->cmdq_client.chan = NULL;
 	}
 
-	if (mtk_crtc->cmdq_client) {
+	if (mtk_crtc->cmdq_client.chan) {
 		ret = of_property_read_u32_index(priv->mutex_node,
 						 "mediatek,gce-events",
 						 drm_crtc_index(&mtk_crtc->base),
@@ -846,8 +939,18 @@
 		if (ret) {
 			dev_dbg(dev, "mtk_crtc %d failed to get mediatek,gce-events property\n",
 				drm_crtc_index(&mtk_crtc->base));
-			cmdq_mbox_destroy(mtk_crtc->cmdq_client);
-			mtk_crtc->cmdq_client = NULL;
+			mbox_free_channel(mtk_crtc->cmdq_client.chan);
+			mtk_crtc->cmdq_client.chan = NULL;
+		} else {
+			ret = mtk_drm_cmdq_pkt_create(&mtk_crtc->cmdq_client,
+						      &mtk_crtc->cmdq_handle,
+						      PAGE_SIZE);
+			if (ret) {
+				dev_dbg(dev, "mtk_crtc %d failed to create cmdq packet\n",
+					drm_crtc_index(&mtk_crtc->base));
+				mbox_free_channel(mtk_crtc->cmdq_client.chan);
+				mtk_crtc->cmdq_client.chan = NULL;
+			}
 		}
 	}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
@@ -276,6 +276,8 @@
 	.config = mtk_ovl_config,
 	.start = mtk_ovl_start,
 	.stop = mtk_ovl_stop,
+	.register_vblank_cb = mtk_ovl_register_vblank_cb,
+	.unregister_vblank_cb = mtk_ovl_unregister_vblank_cb,
 	.enable_vblank = mtk_ovl_enable_vblank,
 	.disable_vblank = mtk_ovl_disable_vblank,
 	.supported_rotations = mtk_ovl_supported_rotations,
@@ -292,6 +294,8 @@
 	.config = mtk_rdma_config,
 	.start = mtk_rdma_start,
 	.stop = mtk_rdma_stop,
+	.register_vblank_cb = mtk_rdma_register_vblank_cb,
+	.unregister_vblank_cb = mtk_rdma_unregister_vblank_cb,
 	.enable_vblank = mtk_rdma_enable_vblank,
 	.disable_vblank = mtk_rdma_disable_vblank,
 	.layer_nr = mtk_rdma_layer_nr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h
@@ -47,9 +47,11 @@
 		       unsigned int bpc, struct cmdq_pkt *cmdq_pkt);
 	void (*start)(struct device *dev);
 	void (*stop)(struct device *dev);
-	void (*enable_vblank)(struct device *dev,
-			      void (*vblank_cb)(void *),
-			      void *vblank_cb_data);
+	void (*register_vblank_cb)(struct device *dev,
+				   void (*vblank_cb)(void *),
+				   void *vblank_cb_data);
+	void (*unregister_vblank_cb)(struct device *dev);
+	void (*enable_vblank)(struct device *dev);
 	void (*disable_vblank)(struct device *dev);
 	unsigned int (*supported_rotations)(struct device *dev);
 	unsigned int (*layer_nr)(struct device *dev);
@@ -110,12 +112,25 @@
 		comp->funcs->stop(comp->dev);
 }
 
-static inline void mtk_ddp_comp_enable_vblank(struct mtk_ddp_comp *comp,
-					      void (*vblank_cb)(void *),
-					      void *vblank_cb_data)
+static inline void mtk_ddp_comp_register_vblank_cb(struct mtk_ddp_comp *comp,
+						   void (*vblank_cb)(void *),
+						   void *vblank_cb_data)
+{
+	if (comp->funcs && comp->funcs->register_vblank_cb)
+		comp->funcs->register_vblank_cb(comp->dev, vblank_cb,
+						vblank_cb_data);
+}
+
+static inline void mtk_ddp_comp_unregister_vblank_cb(struct mtk_ddp_comp *comp)
+{
+	if (comp->funcs && comp->funcs->unregister_vblank_cb)
+		comp->funcs->unregister_vblank_cb(comp->dev);
+}
+
+static inline void mtk_ddp_comp_enable_vblank(struct mtk_ddp_comp *comp)
 {
 	if (comp->funcs && comp->funcs->enable_vblank)
-		comp->funcs->enable_vblank(comp->dev, vblank_cb, vblank_cb_data);
+		comp->funcs->enable_vblank(comp->dev);
 }
 
 static inline void mtk_ddp_comp_disable_vblank(struct mtk_ddp_comp *comp)
@@ -130,7 +145,11 @@
 	if (comp->funcs && comp->funcs->supported_rotations)
 		return comp->funcs->supported_rotations(comp->dev);
 
-	return 0;
+	/*
+	 * In order to pass IGT tests, DRM_MODE_ROTATE_0 is required when
+	 * rotation is not supported.
+	 */
+	return DRM_MODE_ROTATE_0;
 }
 
 static inline unsigned int mtk_ddp_comp_layer_nr(struct mtk_ddp_comp *comp)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_drm_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_drm_drv.c
@@ -376,6 +376,7 @@
 err_deinit:
 	mtk_drm_kms_deinit(drm);
 err_free:
+	private->drm = NULL;
 	drm_dev_put(drm);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_drm_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_drm_gem.c
@@ -33,6 +33,9 @@
 
 	size = round_up(size, PAGE_SIZE);
 
+	if (size == 0)
+		return ERR_PTR(-EINVAL);
+
 	mtk_gem_obj = kzalloc(sizeof(*mtk_gem_obj), GFP_KERNEL);
 	if (!mtk_gem_obj)
 		return ERR_PTR(-ENOMEM);
@@ -164,8 +167,6 @@
 
 	ret = dma_mmap_attrs(priv->dma_dev, vma, mtk_gem->cookie,
 			     mtk_gem->dma_addr, obj->size, mtk_gem->dma_attrs);
-	if (ret)
-		drm_gem_vm_close(vma);
 
 	return ret;
 }
@@ -244,7 +245,11 @@
 
 	mtk_gem->kvaddr = vmap(mtk_gem->pages, npages, VM_MAP,
 			       pgprot_writecombine(PAGE_KERNEL));
-
+	if (!mtk_gem->kvaddr) {
+		kfree(sgt);
+		kfree(mtk_gem->pages);
+		return -ENOMEM;
+	}
 out:
 	kfree(sgt);
 	dma_buf_map_set_vaddr(map, mtk_gem->kvaddr);
@@ -261,6 +266,6 @@
 		return;
 
 	vunmap(vaddr);
-	mtk_gem->kvaddr = 0;
+	mtk_gem->kvaddr = NULL;
 	kfree(mtk_gem->pages);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_drm_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_drm_plane.c
@@ -154,9 +154,11 @@
 	plane->state->src_y = new_state->src_y;
 	plane->state->src_h = new_state->src_h;
 	plane->state->src_w = new_state->src_w;
-	swap(plane->state->fb, new_state->fb);
+	plane->state->dst.x1 = new_state->dst.x1;
+	plane->state->dst.y1 = new_state->dst.y1;
 
 	mtk_plane_update_new_state(new_state, new_plane_state);
+	swap(plane->state->fb, new_state->fb);
 	wmb(); /* Make sure the above parameters are set before update */
 	new_plane_state->pending.async_dirty = true;
 	mtk_drm_crtc_async_update(new_state->crtc, plane, state);
@@ -256,7 +258,7 @@
 		return err;
 	}
 
-	if (supported_rotations & ~DRM_MODE_ROTATE_0) {
+	if (supported_rotations) {
 		err = drm_plane_create_rotation_property(plane,
 							 DRM_MODE_ROTATE_0,
 							 supported_rotations);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -11,6 +11,7 @@
 #include <linux/of_platform.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
+#include <linux/reset.h>
 
 #include <video/mipi_display.h>
 #include <video/videomode.h>
@@ -69,8 +70,8 @@
 #define DSI_PS_WC			0x3fff
 #define DSI_PS_SEL			(3 << 16)
 #define PACKED_PS_16BIT_RGB565		(0 << 16)
-#define LOOSELY_PS_18BIT_RGB666		(1 << 16)
-#define PACKED_PS_18BIT_RGB666		(2 << 16)
+#define PACKED_PS_18BIT_RGB666		(1 << 16)
+#define LOOSELY_PS_24BIT_RGB666		(2 << 16)
 #define PACKED_PS_24BIT_RGB888		(3 << 16)
 
 #define DSI_VSA_NL		0x20
@@ -202,6 +203,7 @@
 	struct mtk_phy_timing phy_timing;
 	int refcount;
 	bool enabled;
+	bool lanes_ready;
 	u32 irq_data;
 	wait_queue_head_t irq_wait_queue;
 	const struct mtk_dsi_driver_data *driver_data;
@@ -364,10 +366,10 @@
 		ps_bpp_mode |= PACKED_PS_24BIT_RGB888;
 		break;
 	case MIPI_DSI_FMT_RGB666:
-		ps_bpp_mode |= PACKED_PS_18BIT_RGB666;
+		ps_bpp_mode |= LOOSELY_PS_24BIT_RGB666;
 		break;
 	case MIPI_DSI_FMT_RGB666_PACKED:
-		ps_bpp_mode |= LOOSELY_PS_18BIT_RGB666;
+		ps_bpp_mode |= PACKED_PS_18BIT_RGB666;
 		break;
 	case MIPI_DSI_FMT_RGB565:
 		ps_bpp_mode |= PACKED_PS_16BIT_RGB565;
@@ -404,7 +406,7 @@
 	if (dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS)
 		tmp_reg |= HSTX_CKLP_EN;
 
-	if (!(dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET))
+	if (dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET)
 		tmp_reg |= DIS_EOT;
 
 	writel(tmp_reg, dsi->regs + DSI_TXRX_CTRL);
@@ -421,7 +423,7 @@
 		dsi_tmp_buf_bpp = 3;
 		break;
 	case MIPI_DSI_FMT_RGB666:
-		tmp_reg = LOOSELY_PS_18BIT_RGB666;
+		tmp_reg = LOOSELY_PS_24BIT_RGB666;
 		dsi_tmp_buf_bpp = 3;
 		break;
 	case MIPI_DSI_FMT_RGB666_PACKED:
@@ -481,7 +483,7 @@
 			  timing->da_hs_zero + timing->da_hs_exit + 3;
 
 	delta = dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST ? 18 : 12;
-	delta += dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET ? 2 : 0;
+	delta += dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET ? 0 : 2;
 
 	horizontal_frontporch_byte = vm->hfront_porch * dsi_tmp_buf_bpp;
 	horizontal_front_back_byte = horizontal_frontporch_byte + horizontal_backporch_byte;
@@ -648,18 +650,11 @@
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_phy_timconfig(dsi);
 
-	mtk_dsi_rxtx_control(dsi);
-	usleep_range(30, 100);
-	mtk_dsi_reset_dphy(dsi);
 	mtk_dsi_ps_control_vact(dsi);
 	mtk_dsi_set_vm_cmd(dsi);
 	mtk_dsi_config_vdo_timing(dsi);
 	mtk_dsi_set_interrupt_enable(dsi);
 
-	mtk_dsi_clk_ulp_mode_leave(dsi);
-	mtk_dsi_lane0_ulp_mode_leave(dsi);
-	mtk_dsi_clk_hs_mode(dsi, 0);
-
 	return 0;
 err_disable_engine_clk:
 	clk_disable_unprepare(dsi->engine_clk);
@@ -691,6 +686,8 @@
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_lane0_ulp_mode_enter(dsi);
 	mtk_dsi_clk_ulp_mode_enter(dsi);
+	/* set the lane number as 0 to pull down mipi */
+	writel(0, dsi->regs + DSI_TXRX_CTRL);
 
 	mtk_dsi_disable(dsi);
 
@@ -698,21 +695,31 @@
 	clk_disable_unprepare(dsi->digital_clk);
 
 	phy_power_off(dsi->phy);
+
+	dsi->lanes_ready = false;
 }
 
-static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
+static void mtk_dsi_lane_ready(struct mtk_dsi *dsi)
 {
-	int ret;
+	if (!dsi->lanes_ready) {
+		dsi->lanes_ready = true;
+		mtk_dsi_rxtx_control(dsi);
+		usleep_range(30, 100);
+		mtk_dsi_reset_dphy(dsi);
+		mtk_dsi_clk_ulp_mode_leave(dsi);
+		mtk_dsi_lane0_ulp_mode_leave(dsi);
+		mtk_dsi_clk_hs_mode(dsi, 0);
+		usleep_range(1000, 3000);
+		/* The reaction time after pulling up the mipi signal for dsi_rx */
+	}
+}
 
+static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
+{
 	if (dsi->enabled)
 		return;
 
-	ret = mtk_dsi_poweron(dsi);
-	if (ret < 0) {
-		DRM_ERROR("failed to power on dsi\n");
-		return;
-	}
-
+	mtk_dsi_lane_ready(dsi);
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
@@ -726,8 +733,6 @@
 	if (!dsi->enabled)
 		return;
 
-	mtk_dsi_poweroff(dsi);
-
 	dsi->enabled = false;
 }
 
@@ -750,24 +755,53 @@
 	drm_display_mode_to_videomode(adjusted, &dsi->vm);
 }
 
-static void mtk_dsi_bridge_disable(struct drm_bridge *bridge)
+static void mtk_dsi_bridge_atomic_disable(struct drm_bridge *bridge,
+					  struct drm_bridge_state *old_bridge_state)
 {
 	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
 
 	mtk_output_dsi_disable(dsi);
 }
 
-static void mtk_dsi_bridge_enable(struct drm_bridge *bridge)
+static void mtk_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
+					 struct drm_bridge_state *old_bridge_state)
 {
 	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
 
+	if (dsi->refcount == 0)
+		return;
+
 	mtk_output_dsi_enable(dsi);
 }
 
+static void mtk_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
+					     struct drm_bridge_state *old_bridge_state)
+{
+	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
+	int ret;
+
+	ret = mtk_dsi_poweron(dsi);
+	if (ret < 0)
+		DRM_ERROR("failed to power on dsi\n");
+}
+
+static void mtk_dsi_bridge_atomic_post_disable(struct drm_bridge *bridge,
+					       struct drm_bridge_state *old_bridge_state)
+{
+	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
+
+	mtk_dsi_poweroff(dsi);
+}
+
 static const struct drm_bridge_funcs mtk_dsi_bridge_funcs = {
 	.attach = mtk_dsi_bridge_attach,
-	.disable = mtk_dsi_bridge_disable,
-	.enable = mtk_dsi_bridge_enable,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_disable = mtk_dsi_bridge_atomic_disable,
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_enable = mtk_dsi_bridge_atomic_enable,
+	.atomic_pre_enable = mtk_dsi_bridge_atomic_pre_enable,
+	.atomic_post_disable = mtk_dsi_bridge_atomic_post_disable,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
 	.mode_set = mtk_dsi_bridge_mode_set,
 };
 
@@ -886,28 +920,39 @@
 				     const struct mipi_dsi_msg *msg)
 {
 	struct mtk_dsi *dsi = host_to_dsi(host);
-	u32 recv_cnt, i;
+	ssize_t recv_cnt;
 	u8 read_data[16];
 	void *src_addr;
 	u8 irq_flag = CMD_DONE_INT_FLAG;
+	u32 dsi_mode;
+	int ret, i;
 
-	if (readl(dsi->regs + DSI_MODE_CTRL) & MODE) {
-		DRM_ERROR("dsi engine is not command mode\n");
-		return -EINVAL;
+	dsi_mode = readl(dsi->regs + DSI_MODE_CTRL);
+	if (dsi_mode & MODE) {
+		mtk_dsi_stop(dsi);
+		ret = mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
+		if (ret)
+			goto restore_dsi_mode;
 	}
 
 	if (MTK_DSI_HOST_IS_READ(msg->type))
 		irq_flag |= LPRX_RD_RDY_INT_FLAG;
 
-	if (mtk_dsi_host_send_cmd(dsi, msg, irq_flag) < 0)
-		return -ETIME;
+	mtk_dsi_lane_ready(dsi);
 
-	if (!MTK_DSI_HOST_IS_READ(msg->type))
-		return 0;
+	ret = mtk_dsi_host_send_cmd(dsi, msg, irq_flag);
+	if (ret)
+		goto restore_dsi_mode;
+
+	if (!MTK_DSI_HOST_IS_READ(msg->type)) {
+		recv_cnt = 0;
+		goto restore_dsi_mode;
+	}
 
 	if (!msg->rx_buf) {
 		DRM_ERROR("dsi receive buffer size may be NULL\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto restore_dsi_mode;
 	}
 
 	for (i = 0; i < 16; i++)
@@ -929,10 +974,16 @@
 	if (recv_cnt)
 		memcpy(msg->rx_buf, src_addr, recv_cnt);
 
-	DRM_INFO("dsi get %d byte data from the panel address(0x%x)\n",
+	DRM_INFO("dsi get %zd byte data from the panel address(0x%x)\n",
 		 recv_cnt, *((u8 *)(msg->tx_buf)));
 
-	return recv_cnt;
+restore_dsi_mode:
+	if (dsi_mode & MODE) {
+		mtk_dsi_set_mode(dsi);
+		mtk_dsi_start(dsi);
+	}
+
+	return ret < 0 ? ret : recv_cnt;
 }
 
 static const struct mipi_dsi_host_ops mtk_dsi_ops = {
@@ -980,8 +1031,10 @@
 	struct mtk_dsi *dsi = dev_get_drvdata(dev);
 
 	ret = mtk_dsi_encoder_init(drm, dsi);
+	if (ret)
+		return ret;
 
-	return ret;
+	return device_reset_optional(dev);
 }
 
 static void mtk_dsi_unbind(struct device *dev, struct device *master,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mediatek/mtk_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mediatek/mtk_hdmi.c
@@ -138,7 +138,7 @@
 
 struct hdmi_audio_param {
 	enum hdmi_audio_coding_type aud_codec;
-	enum hdmi_audio_sample_size aud_sampe_size;
+	enum hdmi_audio_sample_size aud_sample_size;
 	enum hdmi_aud_input_type aud_input_type;
 	enum hdmi_aud_i2s_fmt aud_i2s_fmt;
 	enum hdmi_aud_mclk aud_mclk;
@@ -174,6 +174,7 @@
 	unsigned int sys_offset;
 	void __iomem *regs;
 	enum hdmi_colorspace csp;
+	struct platform_device *audio_pdev;
 	struct hdmi_audio_param aud_param;
 	bool audio_enable;
 	bool powered;
@@ -1075,7 +1076,7 @@
 
 	hdmi->csp = HDMI_COLORSPACE_RGB;
 	aud_param->aud_codec = HDMI_AUDIO_CODING_TYPE_PCM;
-	aud_param->aud_sampe_size = HDMI_AUDIO_SAMPLE_SIZE_16;
+	aud_param->aud_sample_size = HDMI_AUDIO_SAMPLE_SIZE_16;
 	aud_param->aud_input_type = HDMI_AUD_INPUT_I2S;
 	aud_param->aud_i2s_fmt = HDMI_I2S_MODE_I2S_24BIT;
 	aud_param->aud_mclk = HDMI_AUD_MCLK_128FS;
@@ -1203,9 +1204,10 @@
 	return mtk_hdmi_update_plugged_status(hdmi);
 }
 
-static int mtk_hdmi_bridge_mode_valid(struct drm_bridge *bridge,
-				      const struct drm_display_info *info,
-				      const struct drm_display_mode *mode)
+static enum drm_mode_status
+mtk_hdmi_bridge_mode_valid(struct drm_bridge *bridge,
+			   const struct drm_display_info *info,
+			   const struct drm_display_mode *mode)
 {
 	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
 	struct drm_bridge *next_bridge;
@@ -1224,12 +1226,14 @@
 			return MODE_BAD;
 	}
 
-	if (hdmi->conf->cea_modes_only && !drm_match_cea_mode(mode))
-		return MODE_BAD;
+	if (hdmi->conf) {
+		if (hdmi->conf->cea_modes_only && !drm_match_cea_mode(mode))
+			return MODE_BAD;
 
-	if (hdmi->conf->max_mode_clock &&
-	    mode->clock > hdmi->conf->max_mode_clock)
-		return MODE_CLOCK_HIGH;
+		if (hdmi->conf->max_mode_clock &&
+		    mode->clock > hdmi->conf->max_mode_clock)
+			return MODE_CLOCK_HIGH;
+	}
 
 	if (mode->clock < 27000)
 		return MODE_CLOCK_LOW;
@@ -1573,14 +1577,14 @@
 	switch (daifmt->fmt) {
 	case HDMI_I2S:
 		hdmi_params.aud_codec = HDMI_AUDIO_CODING_TYPE_PCM;
-		hdmi_params.aud_sampe_size = HDMI_AUDIO_SAMPLE_SIZE_16;
+		hdmi_params.aud_sample_size = HDMI_AUDIO_SAMPLE_SIZE_16;
 		hdmi_params.aud_input_type = HDMI_AUD_INPUT_I2S;
 		hdmi_params.aud_i2s_fmt = HDMI_I2S_MODE_I2S_24BIT;
 		hdmi_params.aud_mclk = HDMI_AUD_MCLK_128FS;
 		break;
 	case HDMI_SPDIF:
 		hdmi_params.aud_codec = HDMI_AUDIO_CODING_TYPE_PCM;
-		hdmi_params.aud_sampe_size = HDMI_AUDIO_SAMPLE_SIZE_16;
+		hdmi_params.aud_sample_size = HDMI_AUDIO_SAMPLE_SIZE_16;
 		hdmi_params.aud_input_type = HDMI_AUD_INPUT_SPDIF;
 		break;
 	default:
@@ -1664,6 +1668,11 @@
 	.no_capture_mute = 1,
 };
 
+static void mtk_hdmi_unregister_audio_driver(void *data)
+{
+	platform_device_unregister(data);
+}
+
 static int mtk_hdmi_register_audio_driver(struct device *dev)
 {
 	struct mtk_hdmi *hdmi = dev_get_drvdata(dev);
@@ -1673,13 +1682,20 @@
 		.i2s = 1,
 		.data = hdmi,
 	};
-	struct platform_device *pdev;
+	int ret;
+
+	hdmi->audio_pdev = platform_device_register_data(dev,
+							 HDMI_CODEC_DRV_NAME,
+							 PLATFORM_DEVID_AUTO,
+							 &codec_data,
+							 sizeof(codec_data));
+	if (IS_ERR(hdmi->audio_pdev))
+		return PTR_ERR(hdmi->audio_pdev);
 
-	pdev = platform_device_register_data(dev, HDMI_CODEC_DRV_NAME,
-					     PLATFORM_DEVID_AUTO, &codec_data,
-					     sizeof(codec_data));
-	if (IS_ERR(pdev))
-		return PTR_ERR(pdev);
+	ret = devm_add_action_or_reset(dev, mtk_hdmi_unregister_audio_driver,
+				       hdmi->audio_pdev);
+	if (ret)
+		return ret;
 
 	DRM_INFO("%s driver bound to HDMI\n", HDMI_CODEC_DRV_NAME);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/Kconfig
@@ -6,9 +6,11 @@
 	select DRM_KMS_HELPER
 	select DRM_KMS_CMA_HELPER
 	select DRM_GEM_CMA_HELPER
+	select DRM_DISPLAY_CONNECTOR
 	select VIDEOMODE_HELPERS
 	select REGMAP_MMIO
 	select MESON_CANVAS
+	select CEC_CORE if CEC_NOTIFIER
 
 config DRM_MESON_DW_HDMI
 	tristate "HDMI Synopsys Controller support for Amlogic Meson Display"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/Makefile
@@ -2,6 +2,7 @@
 meson-drm-y := meson_drv.o meson_plane.o meson_crtc.o meson_venc_cvbs.o
 meson-drm-y += meson_viu.o meson_vpp.o meson_venc.o meson_vclk.o meson_overlay.o
 meson-drm-y += meson_rdma.o meson_osd_afbcd.o
+meson-drm-y += meson_encoder_hdmi.o
 
 obj-$(CONFIG_DRM_MESON) += meson-drm.o
 obj-$(CONFIG_DRM_MESON_DW_HDMI) += meson_dw_hdmi.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_drv.c
@@ -32,6 +32,7 @@
 #include "meson_osd_afbcd.h"
 #include "meson_registers.h"
 #include "meson_venc_cvbs.h"
+#include "meson_encoder_hdmi.h"
 #include "meson_viu.h"
 #include "meson_vpp.h"
 #include "meson_rdma.h"
@@ -113,8 +114,11 @@
 	for_each_endpoint_of_node(dev->of_node, ep) {
 		/* If the endpoint node exists, consider it enabled */
 		remote = of_graph_get_remote_port(ep);
-		if (remote)
+		if (remote) {
+			of_node_put(remote);
+			of_node_put(ep);
 			return true;
+		}
 	}
 
 	return false;
@@ -206,8 +210,7 @@
 	priv->compat = match->compat;
 	priv->afbcd.ops = match->afbcd_ops;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "vpu");
-	regs = devm_ioremap_resource(dev, res);
+	regs = devm_platform_ioremap_resource_byname(pdev, "vpu");
 	if (IS_ERR(regs)) {
 		ret = PTR_ERR(regs);
 		goto free_drm;
@@ -245,29 +248,20 @@
 	if (ret)
 		goto free_drm;
 	ret = meson_canvas_alloc(priv->canvas, &priv->canvas_id_vd1_0);
-	if (ret) {
-		meson_canvas_free(priv->canvas, priv->canvas_id_osd1);
-		goto free_drm;
-	}
+	if (ret)
+		goto free_canvas_osd1;
 	ret = meson_canvas_alloc(priv->canvas, &priv->canvas_id_vd1_1);
-	if (ret) {
-		meson_canvas_free(priv->canvas, priv->canvas_id_osd1);
-		meson_canvas_free(priv->canvas, priv->canvas_id_vd1_0);
-		goto free_drm;
-	}
+	if (ret)
+		goto free_canvas_vd1_0;
 	ret = meson_canvas_alloc(priv->canvas, &priv->canvas_id_vd1_2);
-	if (ret) {
-		meson_canvas_free(priv->canvas, priv->canvas_id_osd1);
-		meson_canvas_free(priv->canvas, priv->canvas_id_vd1_0);
-		meson_canvas_free(priv->canvas, priv->canvas_id_vd1_1);
-		goto free_drm;
-	}
+	if (ret)
+		goto free_canvas_vd1_1;
 
 	priv->vsync_irq = platform_get_irq(pdev, 0);
 
 	ret = drm_vblank_init(drm, 1);
 	if (ret)
-		goto free_drm;
+		goto free_canvas_vd1_2;
 
 	/* Assign limits per soc revision/package */
 	for (i = 0 ; i < ARRAY_SIZE(meson_drm_soc_attrs) ; ++i) {
@@ -283,11 +277,11 @@
 	 */
 	ret = drm_aperture_remove_framebuffers(false, &meson_driver);
 	if (ret)
-		goto free_drm;
+		goto free_canvas_vd1_2;
 
 	ret = drmm_mode_config_init(drm);
 	if (ret)
-		goto free_drm;
+		goto free_canvas_vd1_2;
 	drm->mode_config.max_width = 3840;
 	drm->mode_config.max_height = 2160;
 	drm->mode_config.funcs = &meson_mode_config_funcs;
@@ -302,38 +296,42 @@
 	if (priv->afbcd.ops) {
 		ret = priv->afbcd.ops->init(priv);
 		if (ret)
-			return ret;
+			goto free_canvas_vd1_2;
 	}
 
 	/* Encoder Initialization */
 
 	ret = meson_venc_cvbs_create(priv);
 	if (ret)
-		goto free_drm;
+		goto exit_afbcd;
 
 	if (has_components) {
 		ret = component_bind_all(drm->dev, drm);
 		if (ret) {
 			dev_err(drm->dev, "Couldn't bind all components\n");
-			goto free_drm;
+			goto exit_afbcd;
 		}
 	}
 
+	ret = meson_encoder_hdmi_init(priv);
+	if (ret)
+		goto unbind_all;
+
 	ret = meson_plane_create(priv);
 	if (ret)
-		goto free_drm;
+		goto unbind_all;
 
 	ret = meson_overlay_create(priv);
 	if (ret)
-		goto free_drm;
+		goto unbind_all;
 
 	ret = meson_crtc_create(priv);
 	if (ret)
-		goto free_drm;
+		goto unbind_all;
 
 	ret = request_irq(priv->vsync_irq, meson_irq, 0, drm->driver->name, drm);
 	if (ret)
-		goto free_drm;
+		goto unbind_all;
 
 	drm_mode_config_reset(drm);
 
@@ -351,6 +349,20 @@
 
 uninstall_irq:
 	free_irq(priv->vsync_irq, drm);
+unbind_all:
+	if (has_components)
+		component_unbind_all(drm->dev, drm);
+exit_afbcd:
+	if (priv->afbcd.ops)
+		priv->afbcd.ops->exit(priv);
+free_canvas_vd1_2:
+	meson_canvas_free(priv->canvas, priv->canvas_id_vd1_2);
+free_canvas_vd1_1:
+	meson_canvas_free(priv->canvas, priv->canvas_id_vd1_1);
+free_canvas_vd1_0:
+	meson_canvas_free(priv->canvas, priv->canvas_id_vd1_0);
+free_canvas_osd1:
+	meson_canvas_free(priv->canvas, priv->canvas_id_osd1);
 free_drm:
 	drm_dev_put(drm);
 
@@ -377,14 +389,12 @@
 	drm_dev_unregister(drm);
 	drm_kms_helper_poll_fini(drm);
 	drm_atomic_helper_shutdown(drm);
-	component_unbind_all(dev, drm);
 	free_irq(priv->vsync_irq, drm);
 	drm_dev_put(drm);
+	component_unbind_all(dev, drm);
 
-	if (priv->afbcd.ops) {
-		priv->afbcd.ops->reset(priv);
-		meson_rdma_free(priv);
-	}
+	if (priv->afbcd.ops)
+		priv->afbcd.ops->exit(priv);
 }
 
 static const struct component_master_ops meson_drv_master_ops = {
@@ -512,6 +522,13 @@
 	return 0;
 };
 
+static int meson_drv_remove(struct platform_device *pdev)
+{
+	component_master_del(&pdev->dev, &meson_drv_master_ops);
+
+	return 0;
+}
+
 static struct meson_drm_match_data meson_drm_gxbb_data = {
 	.compat = VPU_COMPATIBLE_GXBB,
 };
@@ -549,6 +566,7 @@
 
 static struct platform_driver meson_drm_platform_driver = {
 	.probe      = meson_drv_probe,
+	.remove     = meson_drv_remove,
 	.shutdown   = meson_drv_shutdown,
 	.driver     = {
 		.name	= "meson-drm",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_dw_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_dw_hdmi.c
@@ -22,14 +22,11 @@
 #include <drm/drm_probe_helper.h>
 #include <drm/drm_print.h>
 
-#include <linux/media-bus-format.h>
 #include <linux/videodev2.h>
 
 #include "meson_drv.h"
 #include "meson_dw_hdmi.h"
 #include "meson_registers.h"
-#include "meson_vclk.h"
-#include "meson_venc.h"
 
 #define DRIVER_NAME "meson-dw-hdmi"
 #define DRIVER_DESC "Amlogic Meson HDMI-TX DRM driver"
@@ -108,6 +105,8 @@
 #define HHI_HDMI_CLK_CNTL	0x1cc /* 0x73 */
 #define HHI_HDMI_PHY_CNTL0	0x3a0 /* 0xe8 */
 #define HHI_HDMI_PHY_CNTL1	0x3a4 /* 0xe9 */
+#define  PHY_CNTL1_INIT		0x03900000
+#define  PHY_INVERT		BIT(17)
 #define HHI_HDMI_PHY_CNTL2	0x3a8 /* 0xea */
 #define HHI_HDMI_PHY_CNTL3	0x3ac /* 0xeb */
 #define HHI_HDMI_PHY_CNTL4	0x3b0 /* 0xec */
@@ -132,11 +131,11 @@
 				    unsigned int addr);
 	void		(*dwc_write)(struct meson_dw_hdmi *dw_hdmi,
 				     unsigned int addr, unsigned int data);
+	u32 cntl0_init;
+	u32 cntl1_init;
 };
 
 struct meson_dw_hdmi {
-	struct drm_encoder encoder;
-	struct drm_bridge bridge;
 	struct dw_hdmi_plat_data dw_plat_data;
 	struct meson_drm *priv;
 	struct device *dev;
@@ -148,12 +147,8 @@
 	struct regulator *hdmi_supply;
 	u32 irq_stat;
 	struct dw_hdmi *hdmi;
-	unsigned long output_bus_fmt;
+	struct drm_bridge *bridge;
 };
-#define encoder_to_meson_dw_hdmi(x) \
-	container_of(x, struct meson_dw_hdmi, encoder)
-#define bridge_to_meson_dw_hdmi(x) \
-	container_of(x, struct meson_dw_hdmi, bridge)
 
 static inline int dw_hdmi_is_compatible(struct meson_dw_hdmi *dw_hdmi,
 					const char *compat)
@@ -295,14 +290,14 @@
 
 /* Setup PHY bandwidth modes */
 static void meson_hdmi_phy_setup_mode(struct meson_dw_hdmi *dw_hdmi,
-				      const struct drm_display_mode *mode)
+				      const struct drm_display_mode *mode,
+				      bool mode_is_420)
 {
 	struct meson_drm *priv = dw_hdmi->priv;
 	unsigned int pixel_clock = mode->clock;
 
 	/* For 420, pixel clock is half unlike venc clock */
-	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
-		pixel_clock /= 2;
+	if (mode_is_420) pixel_clock /= 2;
 
 	if (dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
 	    dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-gxm-dw-hdmi")) {
@@ -374,91 +369,27 @@
 	mdelay(2);
 }
 
-static void dw_hdmi_set_vclk(struct meson_dw_hdmi *dw_hdmi,
-			     const struct drm_display_mode *mode)
-{
-	struct meson_drm *priv = dw_hdmi->priv;
-	int vic = drm_match_cea_mode(mode);
-	unsigned int phy_freq;
-	unsigned int vclk_freq;
-	unsigned int venc_freq;
-	unsigned int hdmi_freq;
-
-	vclk_freq = mode->clock;
-
-	/* For 420, pixel clock is half unlike venc clock */
-	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
-		vclk_freq /= 2;
-
-	/* TMDS clock is pixel_clock * 10 */
-	phy_freq = vclk_freq * 10;
-
-	if (!vic) {
-		meson_vclk_setup(priv, MESON_VCLK_TARGET_DMT, phy_freq,
-				 vclk_freq, vclk_freq, vclk_freq, false);
-		return;
-	}
-
-	/* 480i/576i needs global pixel doubling */
-	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
-		vclk_freq *= 2;
-
-	venc_freq = vclk_freq;
-	hdmi_freq = vclk_freq;
-
-	/* VENC double pixels for 1080i, 720p and YUV420 modes */
-	if (meson_venc_hdmi_venc_repeat(vic) ||
-	    dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
-		venc_freq *= 2;
-
-	vclk_freq = max(venc_freq, hdmi_freq);
-
-	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
-		venc_freq /= 2;
-
-	DRM_DEBUG_DRIVER("vclk:%d phy=%d venc=%d hdmi=%d enci=%d\n",
-		phy_freq, vclk_freq, venc_freq, hdmi_freq,
-		priv->venc.hdmi_use_enci);
-
-	meson_vclk_setup(priv, MESON_VCLK_TARGET_HDMI, phy_freq, vclk_freq,
-			 venc_freq, hdmi_freq, priv->venc.hdmi_use_enci);
-}
-
 static int dw_hdmi_phy_init(struct dw_hdmi *hdmi, void *data,
 			    const struct drm_display_info *display,
 			    const struct drm_display_mode *mode)
 {
 	struct meson_dw_hdmi *dw_hdmi = (struct meson_dw_hdmi *)data;
+	bool is_hdmi2_sink = display->hdmi.scdc.supported;
 	struct meson_drm *priv = dw_hdmi->priv;
 	unsigned int wr_clk =
 		readl_relaxed(priv->io_base + _REG(VPU_HDMI_SETTING));
+	bool mode_is_420 = false;
 
 	DRM_DEBUG_DRIVER("\"%s\" div%d\n", mode->name,
 			 mode->clock > 340000 ? 40 : 10);
 
-	/* Enable clocks */
-	regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL, 0xffff, 0x100);
-
-	/* Bring HDMITX MEM output of power down */
-	regmap_update_bits(priv->hhi, HHI_MEM_PD_REG0, 0xff << 8, 0);
-
-	/* Bring out of reset */
-	dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_SW_RESET,  0);
-
-	/* Enable internal pixclk, tmds_clk, spdif_clk, i2s_clk, cecclk */
-	dw_hdmi_top_write_bits(dw_hdmi, HDMITX_TOP_CLK_CNTL,
-			       0x3, 0x3);
-
-	/* Enable cec_clk and hdcp22_tmdsclk_en */
-	dw_hdmi_top_write_bits(dw_hdmi, HDMITX_TOP_CLK_CNTL,
-			       0x3 << 4, 0x3 << 4);
-
-	/* Enable normal output to PHY */
-	dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_BIST_CNTL, BIT(12));
+	if (drm_mode_is_420_only(display, mode) ||
+	    (!is_hdmi2_sink &&
+	     drm_mode_is_420_also(display, mode)))
+		mode_is_420 = true;
 
 	/* TMDS pattern setup */
-	if (mode->clock > 340000 &&
-	    dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_YUV8_1X24) {
+	if (mode->clock > 340000 && !mode_is_420) {
 		dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_01,
 				  0);
 		dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_23,
@@ -476,21 +407,7 @@
 	dw_hdmi->data->top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_CNTL, 0x2);
 
 	/* Setup PHY parameters */
-	meson_hdmi_phy_setup_mode(dw_hdmi, mode);
-
-	/* Setup PHY */
-	regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1,
-			   0xffff << 16, 0x0390 << 16);
-
-	/* BIT_INVERT */
-	if (dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
-	    dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-gxm-dw-hdmi") ||
-	    dw_hdmi_is_compatible(dw_hdmi, "amlogic,meson-g12a-dw-hdmi"))
-		regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1,
-				   BIT(17), 0);
-	else
-		regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1,
-				   BIT(17), BIT(17));
+	meson_hdmi_phy_setup_mode(dw_hdmi, mode, mode_is_420);
 
 	/* Disable clock, fifo, fifo_wr */
 	regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1, 0xf, 0);
@@ -545,7 +462,9 @@
 
 	DRM_DEBUG_DRIVER("\n");
 
-	regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL0, 0);
+	/* Fallback to init mode */
+	regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL1, dw_hdmi->data->cntl1_init);
+	regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL0, dw_hdmi->data->cntl0_init);
 }
 
 static enum drm_connector_status dw_hdmi_read_hpd(struct dw_hdmi *hdmi,
@@ -622,214 +541,15 @@
 		dw_hdmi_setup_rx_sense(dw_hdmi->hdmi, hpd_connected,
 				       hpd_connected);
 
-		drm_helper_hpd_irq_event(dw_hdmi->encoder.dev);
+		drm_helper_hpd_irq_event(dw_hdmi->bridge->dev);
+		drm_bridge_hpd_notify(dw_hdmi->bridge,
+				      hpd_connected ? connector_status_connected
+						    : connector_status_disconnected);
 	}
 
 	return IRQ_HANDLED;
 }
 
-static enum drm_mode_status
-dw_hdmi_mode_valid(struct dw_hdmi *hdmi, void *data,
-		   const struct drm_display_info *display_info,
-		   const struct drm_display_mode *mode)
-{
-	struct meson_dw_hdmi *dw_hdmi = data;
-	struct meson_drm *priv = dw_hdmi->priv;
-	bool is_hdmi2_sink = display_info->hdmi.scdc.supported;
-	unsigned int phy_freq;
-	unsigned int vclk_freq;
-	unsigned int venc_freq;
-	unsigned int hdmi_freq;
-	int vic = drm_match_cea_mode(mode);
-	enum drm_mode_status status;
-
-	DRM_DEBUG_DRIVER("Modeline " DRM_MODE_FMT "\n", DRM_MODE_ARG(mode));
-
-	/* If sink does not support 540MHz, reject the non-420 HDMI2 modes */
-	if (display_info->max_tmds_clock &&
-	    mode->clock > display_info->max_tmds_clock &&
-	    !drm_mode_is_420_only(display_info, mode) &&
-	    !drm_mode_is_420_also(display_info, mode))
-		return MODE_BAD;
-
-	/* Check against non-VIC supported modes */
-	if (!vic) {
-		status = meson_venc_hdmi_supported_mode(mode);
-		if (status != MODE_OK)
-			return status;
-
-		return meson_vclk_dmt_supported_freq(priv, mode->clock);
-	/* Check against supported VIC modes */
-	} else if (!meson_venc_hdmi_supported_vic(vic))
-		return MODE_BAD;
-
-	vclk_freq = mode->clock;
-
-	/* For 420, pixel clock is half unlike venc clock */
-	if (drm_mode_is_420_only(display_info, mode) ||
-	    (!is_hdmi2_sink &&
-	     drm_mode_is_420_also(display_info, mode)))
-		vclk_freq /= 2;
-
-	/* TMDS clock is pixel_clock * 10 */
-	phy_freq = vclk_freq * 10;
-
-	/* 480i/576i needs global pixel doubling */
-	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
-		vclk_freq *= 2;
-
-	venc_freq = vclk_freq;
-	hdmi_freq = vclk_freq;
-
-	/* VENC double pixels for 1080i, 720p and YUV420 modes */
-	if (meson_venc_hdmi_venc_repeat(vic) ||
-	    drm_mode_is_420_only(display_info, mode) ||
-	    (!is_hdmi2_sink &&
-	     drm_mode_is_420_also(display_info, mode)))
-		venc_freq *= 2;
-
-	vclk_freq = max(venc_freq, hdmi_freq);
-
-	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
-		venc_freq /= 2;
-
-	dev_dbg(dw_hdmi->dev, "%s: vclk:%d phy=%d venc=%d hdmi=%d\n",
-		__func__, phy_freq, vclk_freq, venc_freq, hdmi_freq);
-
-	return meson_vclk_vic_supported_freq(priv, phy_freq, vclk_freq);
-}
-
-/* Encoder */
-
-static const u32 meson_dw_hdmi_out_bus_fmts[] = {
-	MEDIA_BUS_FMT_YUV8_1X24,
-	MEDIA_BUS_FMT_UYYVYY8_0_5X24,
-};
-
-static void meson_venc_hdmi_encoder_destroy(struct drm_encoder *encoder)
-{
-	drm_encoder_cleanup(encoder);
-}
-
-static const struct drm_encoder_funcs meson_venc_hdmi_encoder_funcs = {
-	.destroy        = meson_venc_hdmi_encoder_destroy,
-};
-
-static u32 *
-meson_venc_hdmi_encoder_get_inp_bus_fmts(struct drm_bridge *bridge,
-					struct drm_bridge_state *bridge_state,
-					struct drm_crtc_state *crtc_state,
-					struct drm_connector_state *conn_state,
-					u32 output_fmt,
-					unsigned int *num_input_fmts)
-{
-	u32 *input_fmts = NULL;
-	int i;
-
-	*num_input_fmts = 0;
-
-	for (i = 0 ; i < ARRAY_SIZE(meson_dw_hdmi_out_bus_fmts) ; ++i) {
-		if (output_fmt == meson_dw_hdmi_out_bus_fmts[i]) {
-			*num_input_fmts = 1;
-			input_fmts = kcalloc(*num_input_fmts,
-					     sizeof(*input_fmts),
-					     GFP_KERNEL);
-			if (!input_fmts)
-				return NULL;
-
-			input_fmts[0] = output_fmt;
-
-			break;
-		}
-	}
-
-	return input_fmts;
-}
-
-static int meson_venc_hdmi_encoder_atomic_check(struct drm_bridge *bridge,
-					struct drm_bridge_state *bridge_state,
-					struct drm_crtc_state *crtc_state,
-					struct drm_connector_state *conn_state)
-{
-	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
-
-	dw_hdmi->output_bus_fmt = bridge_state->output_bus_cfg.format;
-
-	DRM_DEBUG_DRIVER("output_bus_fmt %lx\n", dw_hdmi->output_bus_fmt);
-
-	return 0;
-}
-
-static void meson_venc_hdmi_encoder_disable(struct drm_bridge *bridge)
-{
-	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
-	struct meson_drm *priv = dw_hdmi->priv;
-
-	DRM_DEBUG_DRIVER("\n");
-
-	writel_bits_relaxed(0x3, 0,
-			    priv->io_base + _REG(VPU_HDMI_SETTING));
-
-	writel_relaxed(0, priv->io_base + _REG(ENCI_VIDEO_EN));
-	writel_relaxed(0, priv->io_base + _REG(ENCP_VIDEO_EN));
-}
-
-static void meson_venc_hdmi_encoder_enable(struct drm_bridge *bridge)
-{
-	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
-	struct meson_drm *priv = dw_hdmi->priv;
-
-	DRM_DEBUG_DRIVER("%s\n", priv->venc.hdmi_use_enci ? "VENCI" : "VENCP");
-
-	if (priv->venc.hdmi_use_enci)
-		writel_relaxed(1, priv->io_base + _REG(ENCI_VIDEO_EN));
-	else
-		writel_relaxed(1, priv->io_base + _REG(ENCP_VIDEO_EN));
-}
-
-static void meson_venc_hdmi_encoder_mode_set(struct drm_bridge *bridge,
-				   const struct drm_display_mode *mode,
-				   const struct drm_display_mode *adjusted_mode)
-{
-	struct meson_dw_hdmi *dw_hdmi = bridge_to_meson_dw_hdmi(bridge);
-	struct meson_drm *priv = dw_hdmi->priv;
-	int vic = drm_match_cea_mode(mode);
-	unsigned int ycrcb_map = VPU_HDMI_OUTPUT_CBYCR;
-	bool yuv420_mode = false;
-
-	DRM_DEBUG_DRIVER("\"%s\" vic %d\n", mode->name, vic);
-
-	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24) {
-		ycrcb_map = VPU_HDMI_OUTPUT_CRYCB;
-		yuv420_mode = true;
-	}
-
-	/* VENC + VENC-DVI Mode setup */
-	meson_venc_hdmi_mode_set(priv, vic, ycrcb_map, yuv420_mode, mode);
-
-	/* VCLK Set clock */
-	dw_hdmi_set_vclk(dw_hdmi, mode);
-
-	if (dw_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
-		/* Setup YUV420 to HDMI-TX, no 10bit diphering */
-		writel_relaxed(2 | (2 << 2),
-			       priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
-	else
-		/* Setup YUV444 to HDMI-TX, no 10bit diphering */
-		writel_relaxed(0, priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
-}
-
-static const struct drm_bridge_funcs meson_venc_hdmi_encoder_bridge_funcs = {
-	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
-	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
-	.atomic_get_input_bus_fmts = meson_venc_hdmi_encoder_get_inp_bus_fmts,
-	.atomic_reset = drm_atomic_helper_bridge_reset,
-	.atomic_check = meson_venc_hdmi_encoder_atomic_check,
-	.enable	= meson_venc_hdmi_encoder_enable,
-	.disable = meson_venc_hdmi_encoder_disable,
-	.mode_set = meson_venc_hdmi_encoder_mode_set,
-};
-
 /* DW HDMI Regmap */
 
 static int meson_dw_hdmi_reg_read(void *context, unsigned int reg,
@@ -862,11 +582,22 @@
 	.fast_io = true,
 };
 
-static const struct meson_dw_hdmi_data meson_dw_hdmi_gx_data = {
+static const struct meson_dw_hdmi_data meson_dw_hdmi_gxbb_data = {
+	.top_read = dw_hdmi_top_read,
+	.top_write = dw_hdmi_top_write,
+	.dwc_read = dw_hdmi_dwc_read,
+	.dwc_write = dw_hdmi_dwc_write,
+	.cntl0_init = 0x0,
+	.cntl1_init = PHY_CNTL1_INIT | PHY_INVERT,
+};
+
+static const struct meson_dw_hdmi_data meson_dw_hdmi_gxl_data = {
 	.top_read = dw_hdmi_top_read,
 	.top_write = dw_hdmi_top_write,
 	.dwc_read = dw_hdmi_dwc_read,
 	.dwc_write = dw_hdmi_dwc_write,
+	.cntl0_init = 0x0,
+	.cntl1_init = PHY_CNTL1_INIT,
 };
 
 static const struct meson_dw_hdmi_data meson_dw_hdmi_g12a_data = {
@@ -874,30 +605,10 @@
 	.top_write = dw_hdmi_g12a_top_write,
 	.dwc_read = dw_hdmi_g12a_dwc_read,
 	.dwc_write = dw_hdmi_g12a_dwc_write,
+	.cntl0_init = 0x000b4242, /* Bandgap */
+	.cntl1_init = PHY_CNTL1_INIT,
 };
 
-static bool meson_hdmi_connector_is_available(struct device *dev)
-{
-	struct device_node *ep, *remote;
-
-	/* HDMI Connector is on the second port, first endpoint */
-	ep = of_graph_get_endpoint_by_regs(dev->of_node, 1, 0);
-	if (!ep)
-		return false;
-
-	/* If the endpoint node exists, consider it enabled */
-	remote = of_graph_get_remote_port(ep);
-	if (remote) {
-		of_node_put(ep);
-		return true;
-	}
-
-	of_node_put(ep);
-	of_node_put(remote);
-
-	return false;
-}
-
 static void meson_dw_hdmi_init(struct meson_dw_hdmi *meson_dw_hdmi)
 {
 	struct meson_drm *priv = meson_dw_hdmi->priv;
@@ -930,6 +641,13 @@
 	meson_dw_hdmi->data->top_write(meson_dw_hdmi,
 				       HDMITX_TOP_CLK_CNTL, 0xff);
 
+	/* Enable normal output to PHY */
+	meson_dw_hdmi->data->top_write(meson_dw_hdmi, HDMITX_TOP_BIST_CNTL, BIT(12));
+
+	/* Setup PHY */
+	regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL1, meson_dw_hdmi->data->cntl1_init);
+	regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL0, meson_dw_hdmi->data->cntl0_init);
+
 	/* Enable HDMI-TX Interrupt */
 	meson_dw_hdmi->data->top_write(meson_dw_hdmi, HDMITX_TOP_INTR_STAT_CLR,
 				       HDMITX_TOP_INTR_CORE);
@@ -976,19 +694,11 @@
 	struct drm_device *drm = data;
 	struct meson_drm *priv = drm->dev_private;
 	struct dw_hdmi_plat_data *dw_plat_data;
-	struct drm_bridge *next_bridge;
-	struct drm_encoder *encoder;
-	struct resource *res;
 	int irq;
 	int ret;
 
 	DRM_DEBUG_DRIVER("\n");
 
-	if (!meson_hdmi_connector_is_available(dev)) {
-		dev_info(drm->dev, "HDMI Output connector not available\n");
-		return -ENODEV;
-	}
-
 	match = of_device_get_match_data(&pdev->dev);
 	if (!match) {
 		dev_err(&pdev->dev, "failed to get match data\n");
@@ -1004,7 +714,6 @@
 	meson_dw_hdmi->dev = dev;
 	meson_dw_hdmi->data = match;
 	dw_plat_data = &meson_dw_hdmi->dw_plat_data;
-	encoder = &meson_dw_hdmi->encoder;
 
 	meson_dw_hdmi->hdmi_supply = devm_regulator_get_optional(dev, "hdmi");
 	if (IS_ERR(meson_dw_hdmi->hdmi_supply)) {
@@ -1042,8 +751,7 @@
 		return PTR_ERR(meson_dw_hdmi->hdmitx_phy);
 	}
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	meson_dw_hdmi->hdmitx = devm_ioremap_resource(dev, res);
+	meson_dw_hdmi->hdmitx = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(meson_dw_hdmi->hdmitx))
 		return PTR_ERR(meson_dw_hdmi->hdmitx);
 
@@ -1076,34 +784,18 @@
 		return ret;
 	}
 
-	/* Encoder */
-
-	ret = drm_encoder_init(drm, encoder, &meson_venc_hdmi_encoder_funcs,
-			       DRM_MODE_ENCODER_TMDS, "meson_hdmi");
-	if (ret) {
-		dev_err(priv->dev, "Failed to init HDMI encoder\n");
-		return ret;
-	}
-
-	meson_dw_hdmi->bridge.funcs = &meson_venc_hdmi_encoder_bridge_funcs;
-	drm_bridge_attach(encoder, &meson_dw_hdmi->bridge, NULL, 0);
-
-	encoder->possible_crtcs = BIT(0);
-
 	meson_dw_hdmi_init(meson_dw_hdmi);
 
-	DRM_DEBUG_DRIVER("encoder initialized\n");
-
 	/* Bridge / Connector */
 
 	dw_plat_data->priv_data = meson_dw_hdmi;
-	dw_plat_data->mode_valid = dw_hdmi_mode_valid;
 	dw_plat_data->phy_ops = &meson_dw_hdmi_phy_ops;
 	dw_plat_data->phy_name = "meson_dw_hdmi_phy";
 	dw_plat_data->phy_data = meson_dw_hdmi;
 	dw_plat_data->input_bus_encoding = V4L2_YCBCR_ENC_709;
 	dw_plat_data->ycbcr_420_allowed = true;
 	dw_plat_data->disable_cec = true;
+	dw_plat_data->output_port = 1;
 
 	if (dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
 	    dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxm-dw-hdmi") ||
@@ -1112,15 +804,11 @@
 
 	platform_set_drvdata(pdev, meson_dw_hdmi);
 
-	meson_dw_hdmi->hdmi = dw_hdmi_probe(pdev,
-					    &meson_dw_hdmi->dw_plat_data);
+	meson_dw_hdmi->hdmi = dw_hdmi_probe(pdev, &meson_dw_hdmi->dw_plat_data);
 	if (IS_ERR(meson_dw_hdmi->hdmi))
 		return PTR_ERR(meson_dw_hdmi->hdmi);
 
-	next_bridge = of_drm_find_bridge(pdev->dev.of_node);
-	if (next_bridge)
-		drm_bridge_attach(encoder, next_bridge,
-				  &meson_dw_hdmi->bridge, 0);
+	meson_dw_hdmi->bridge = of_drm_find_bridge(pdev->dev.of_node);
 
 	DRM_DEBUG_DRIVER("HDMI controller initialized\n");
 
@@ -1187,11 +875,11 @@
 
 static const struct of_device_id meson_dw_hdmi_of_table[] = {
 	{ .compatible = "amlogic,meson-gxbb-dw-hdmi",
-	  .data = &meson_dw_hdmi_gx_data },
+	  .data = &meson_dw_hdmi_gxbb_data },
 	{ .compatible = "amlogic,meson-gxl-dw-hdmi",
-	  .data = &meson_dw_hdmi_gx_data },
+	  .data = &meson_dw_hdmi_gxl_data },
 	{ .compatible = "amlogic,meson-gxm-dw-hdmi",
-	  .data = &meson_dw_hdmi_gx_data },
+	  .data = &meson_dw_hdmi_gxl_data },
 	{ .compatible = "amlogic,meson-g12a-dw-hdmi",
 	  .data = &meson_dw_hdmi_g12a_data },
 	{ }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_encoder_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_encoder_hdmi.c
@@ -0,0 +1,458 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (C) 2015 Amlogic, Inc. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+
+#include <media/cec-notifier.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
+#include <drm/drm_device.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_simple_kms_helper.h>
+
+#include <linux/media-bus-format.h>
+#include <linux/videodev2.h>
+
+#include "meson_drv.h"
+#include "meson_registers.h"
+#include "meson_vclk.h"
+#include "meson_venc.h"
+#include "meson_encoder_hdmi.h"
+
+struct meson_encoder_hdmi {
+	struct drm_encoder encoder;
+	struct drm_bridge bridge;
+	struct drm_bridge *next_bridge;
+	struct drm_connector *connector;
+	struct meson_drm *priv;
+	unsigned long output_bus_fmt;
+	struct cec_notifier *cec_notifier;
+};
+
+#define bridge_to_meson_encoder_hdmi(x) \
+	container_of(x, struct meson_encoder_hdmi, bridge)
+
+static int meson_encoder_hdmi_attach(struct drm_bridge *bridge,
+				     enum drm_bridge_attach_flags flags)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+
+	return drm_bridge_attach(bridge->encoder, encoder_hdmi->next_bridge,
+				 &encoder_hdmi->bridge, flags);
+}
+
+static void meson_encoder_hdmi_detach(struct drm_bridge *bridge)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+
+	cec_notifier_conn_unregister(encoder_hdmi->cec_notifier);
+	encoder_hdmi->cec_notifier = NULL;
+}
+
+static void meson_encoder_hdmi_set_vclk(struct meson_encoder_hdmi *encoder_hdmi,
+					const struct drm_display_mode *mode)
+{
+	struct meson_drm *priv = encoder_hdmi->priv;
+	int vic = drm_match_cea_mode(mode);
+	unsigned int phy_freq;
+	unsigned int vclk_freq;
+	unsigned int venc_freq;
+	unsigned int hdmi_freq;
+
+	vclk_freq = mode->clock;
+
+	/* For 420, pixel clock is half unlike venc clock */
+	if (encoder_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
+		vclk_freq /= 2;
+
+	/* TMDS clock is pixel_clock * 10 */
+	phy_freq = vclk_freq * 10;
+
+	if (!vic) {
+		meson_vclk_setup(priv, MESON_VCLK_TARGET_DMT, phy_freq,
+				 vclk_freq, vclk_freq, vclk_freq, false);
+		return;
+	}
+
+	/* 480i/576i needs global pixel doubling */
+	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
+		vclk_freq *= 2;
+
+	venc_freq = vclk_freq;
+	hdmi_freq = vclk_freq;
+
+	/* VENC double pixels for 1080i, 720p and YUV420 modes */
+	if (meson_venc_hdmi_venc_repeat(vic) ||
+	    encoder_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
+		venc_freq *= 2;
+
+	vclk_freq = max(venc_freq, hdmi_freq);
+
+	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
+		venc_freq /= 2;
+
+	dev_dbg(priv->dev, "vclk:%d phy=%d venc=%d hdmi=%d enci=%d\n",
+		phy_freq, vclk_freq, venc_freq, hdmi_freq,
+		priv->venc.hdmi_use_enci);
+
+	meson_vclk_setup(priv, MESON_VCLK_TARGET_HDMI, phy_freq, vclk_freq,
+			 venc_freq, hdmi_freq, priv->venc.hdmi_use_enci);
+}
+
+static enum drm_mode_status meson_encoder_hdmi_mode_valid(struct drm_bridge *bridge,
+					const struct drm_display_info *display_info,
+					const struct drm_display_mode *mode)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+	struct meson_drm *priv = encoder_hdmi->priv;
+	bool is_hdmi2_sink = display_info->hdmi.scdc.supported;
+	unsigned int phy_freq;
+	unsigned int vclk_freq;
+	unsigned int venc_freq;
+	unsigned int hdmi_freq;
+	int vic = drm_match_cea_mode(mode);
+	enum drm_mode_status status;
+
+	dev_dbg(priv->dev, "Modeline " DRM_MODE_FMT "\n", DRM_MODE_ARG(mode));
+
+	/* If sink does not support 540MHz, reject the non-420 HDMI2 modes */
+	if (display_info->max_tmds_clock &&
+	    mode->clock > display_info->max_tmds_clock &&
+	    !drm_mode_is_420_only(display_info, mode) &&
+	    !drm_mode_is_420_also(display_info, mode))
+		return MODE_BAD;
+
+	/* Check against non-VIC supported modes */
+	if (!vic) {
+		status = meson_venc_hdmi_supported_mode(mode);
+		if (status != MODE_OK)
+			return status;
+
+		return meson_vclk_dmt_supported_freq(priv, mode->clock);
+	/* Check against supported VIC modes */
+	} else if (!meson_venc_hdmi_supported_vic(vic))
+		return MODE_BAD;
+
+	vclk_freq = mode->clock;
+
+	/* For 420, pixel clock is half unlike venc clock */
+	if (drm_mode_is_420_only(display_info, mode) ||
+	    (!is_hdmi2_sink &&
+	     drm_mode_is_420_also(display_info, mode)))
+		vclk_freq /= 2;
+
+	/* TMDS clock is pixel_clock * 10 */
+	phy_freq = vclk_freq * 10;
+
+	/* 480i/576i needs global pixel doubling */
+	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
+		vclk_freq *= 2;
+
+	venc_freq = vclk_freq;
+	hdmi_freq = vclk_freq;
+
+	/* VENC double pixels for 1080i, 720p and YUV420 modes */
+	if (meson_venc_hdmi_venc_repeat(vic) ||
+	    drm_mode_is_420_only(display_info, mode) ||
+	    (!is_hdmi2_sink &&
+	     drm_mode_is_420_also(display_info, mode)))
+		venc_freq *= 2;
+
+	vclk_freq = max(venc_freq, hdmi_freq);
+
+	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
+		venc_freq /= 2;
+
+	dev_dbg(priv->dev, "%s: vclk:%d phy=%d venc=%d hdmi=%d\n",
+		__func__, phy_freq, vclk_freq, venc_freq, hdmi_freq);
+
+	return meson_vclk_vic_supported_freq(priv, phy_freq, vclk_freq);
+}
+
+static void meson_encoder_hdmi_atomic_enable(struct drm_bridge *bridge,
+					     struct drm_bridge_state *bridge_state)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+	struct drm_atomic_state *state = bridge_state->base.state;
+	unsigned int ycrcb_map = VPU_HDMI_OUTPUT_CBYCR;
+	struct meson_drm *priv = encoder_hdmi->priv;
+	struct drm_connector_state *conn_state;
+	const struct drm_display_mode *mode;
+	struct drm_crtc_state *crtc_state;
+	struct drm_connector *connector;
+	bool yuv420_mode = false;
+	int vic;
+
+	connector = drm_atomic_get_new_connector_for_encoder(state, bridge->encoder);
+	if (WARN_ON(!connector))
+		return;
+
+	conn_state = drm_atomic_get_new_connector_state(state, connector);
+	if (WARN_ON(!conn_state))
+		return;
+
+	crtc_state = drm_atomic_get_new_crtc_state(state, conn_state->crtc);
+	if (WARN_ON(!crtc_state))
+		return;
+
+	mode = &crtc_state->adjusted_mode;
+
+	vic = drm_match_cea_mode(mode);
+
+	dev_dbg(priv->dev, "\"%s\" vic %d\n", mode->name, vic);
+
+	if (encoder_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24) {
+		ycrcb_map = VPU_HDMI_OUTPUT_CRYCB;
+		yuv420_mode = true;
+	}
+
+	/* VENC + VENC-DVI Mode setup */
+	meson_venc_hdmi_mode_set(priv, vic, ycrcb_map, yuv420_mode, mode);
+
+	/* VCLK Set clock */
+	meson_encoder_hdmi_set_vclk(encoder_hdmi, mode);
+
+	if (encoder_hdmi->output_bus_fmt == MEDIA_BUS_FMT_UYYVYY8_0_5X24)
+		/* Setup YUV420 to HDMI-TX, no 10bit diphering */
+		writel_relaxed(2 | (2 << 2),
+			       priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
+	else
+		/* Setup YUV444 to HDMI-TX, no 10bit diphering */
+		writel_relaxed(0, priv->io_base + _REG(VPU_HDMI_FMT_CTRL));
+
+	dev_dbg(priv->dev, "%s\n", priv->venc.hdmi_use_enci ? "VENCI" : "VENCP");
+
+	if (priv->venc.hdmi_use_enci)
+		writel_relaxed(1, priv->io_base + _REG(ENCI_VIDEO_EN));
+	else
+		writel_relaxed(1, priv->io_base + _REG(ENCP_VIDEO_EN));
+}
+
+static void meson_encoder_hdmi_atomic_disable(struct drm_bridge *bridge,
+					     struct drm_bridge_state *bridge_state)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+	struct meson_drm *priv = encoder_hdmi->priv;
+
+	writel_bits_relaxed(0x3, 0,
+			    priv->io_base + _REG(VPU_HDMI_SETTING));
+
+	writel_relaxed(0, priv->io_base + _REG(ENCI_VIDEO_EN));
+	writel_relaxed(0, priv->io_base + _REG(ENCP_VIDEO_EN));
+}
+
+static const u32 meson_encoder_hdmi_out_bus_fmts[] = {
+	MEDIA_BUS_FMT_YUV8_1X24,
+	MEDIA_BUS_FMT_UYYVYY8_0_5X24,
+};
+
+static u32 *
+meson_encoder_hdmi_get_inp_bus_fmts(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state,
+					u32 output_fmt,
+					unsigned int *num_input_fmts)
+{
+	u32 *input_fmts = NULL;
+	int i;
+
+	*num_input_fmts = 0;
+
+	for (i = 0 ; i < ARRAY_SIZE(meson_encoder_hdmi_out_bus_fmts) ; ++i) {
+		if (output_fmt == meson_encoder_hdmi_out_bus_fmts[i]) {
+			*num_input_fmts = 1;
+			input_fmts = kcalloc(*num_input_fmts,
+					     sizeof(*input_fmts),
+					     GFP_KERNEL);
+			if (!input_fmts)
+				return NULL;
+
+			input_fmts[0] = output_fmt;
+
+			break;
+		}
+	}
+
+	return input_fmts;
+}
+
+static int meson_encoder_hdmi_atomic_check(struct drm_bridge *bridge,
+					struct drm_bridge_state *bridge_state,
+					struct drm_crtc_state *crtc_state,
+					struct drm_connector_state *conn_state)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+	struct drm_connector_state *old_conn_state =
+		drm_atomic_get_old_connector_state(conn_state->state, conn_state->connector);
+	struct meson_drm *priv = encoder_hdmi->priv;
+
+	encoder_hdmi->output_bus_fmt = bridge_state->output_bus_cfg.format;
+
+	dev_dbg(priv->dev, "output_bus_fmt %lx\n", encoder_hdmi->output_bus_fmt);
+
+	if (!drm_connector_atomic_hdr_metadata_equal(old_conn_state, conn_state))
+		crtc_state->mode_changed = true;
+
+	return 0;
+}
+
+static void meson_encoder_hdmi_hpd_notify(struct drm_bridge *bridge,
+					  enum drm_connector_status status)
+{
+	struct meson_encoder_hdmi *encoder_hdmi = bridge_to_meson_encoder_hdmi(bridge);
+	struct edid *edid;
+
+	if (!encoder_hdmi->cec_notifier)
+		return;
+
+	if (status == connector_status_connected) {
+		edid = drm_bridge_get_edid(encoder_hdmi->next_bridge, encoder_hdmi->connector);
+		if (!edid)
+			return;
+
+		cec_notifier_set_phys_addr_from_edid(encoder_hdmi->cec_notifier, edid);
+
+		kfree(edid);
+	} else
+		cec_notifier_phys_addr_invalidate(encoder_hdmi->cec_notifier);
+}
+
+static const struct drm_bridge_funcs meson_encoder_hdmi_bridge_funcs = {
+	.attach = meson_encoder_hdmi_attach,
+	.detach = meson_encoder_hdmi_detach,
+	.mode_valid = meson_encoder_hdmi_mode_valid,
+	.hpd_notify = meson_encoder_hdmi_hpd_notify,
+	.atomic_enable = meson_encoder_hdmi_atomic_enable,
+	.atomic_disable = meson_encoder_hdmi_atomic_disable,
+	.atomic_get_input_bus_fmts = meson_encoder_hdmi_get_inp_bus_fmts,
+	.atomic_check = meson_encoder_hdmi_atomic_check,
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+	.atomic_reset = drm_atomic_helper_bridge_reset,
+};
+
+int meson_encoder_hdmi_init(struct meson_drm *priv)
+{
+	struct meson_encoder_hdmi *meson_encoder_hdmi;
+	struct platform_device *pdev;
+	struct device_node *remote;
+	int ret;
+
+	meson_encoder_hdmi = devm_kzalloc(priv->dev, sizeof(*meson_encoder_hdmi), GFP_KERNEL);
+	if (!meson_encoder_hdmi)
+		return -ENOMEM;
+
+	/* HDMI Transceiver Bridge */
+	remote = of_graph_get_remote_node(priv->dev->of_node, 1, 0);
+	if (!remote) {
+		dev_err(priv->dev, "HDMI transceiver device is disabled");
+		return 0;
+	}
+
+	meson_encoder_hdmi->next_bridge = of_drm_find_bridge(remote);
+	if (!meson_encoder_hdmi->next_bridge) {
+		dev_err(priv->dev, "Failed to find HDMI transceiver bridge\n");
+		ret = -EPROBE_DEFER;
+		goto err_put_node;
+	}
+
+	/* HDMI Encoder Bridge */
+	meson_encoder_hdmi->bridge.funcs = &meson_encoder_hdmi_bridge_funcs;
+	meson_encoder_hdmi->bridge.of_node = priv->dev->of_node;
+	meson_encoder_hdmi->bridge.type = DRM_MODE_CONNECTOR_HDMIA;
+	meson_encoder_hdmi->bridge.interlace_allowed = true;
+
+	drm_bridge_add(&meson_encoder_hdmi->bridge);
+
+	meson_encoder_hdmi->priv = priv;
+
+	/* Encoder */
+	ret = drm_simple_encoder_init(priv->drm, &meson_encoder_hdmi->encoder,
+				      DRM_MODE_ENCODER_TMDS);
+	if (ret) {
+		dev_err(priv->dev, "Failed to init HDMI encoder: %d\n", ret);
+		goto err_put_node;
+	}
+
+	meson_encoder_hdmi->encoder.possible_crtcs = BIT(0);
+
+	/* Attach HDMI Encoder Bridge to Encoder */
+	ret = drm_bridge_attach(&meson_encoder_hdmi->encoder, &meson_encoder_hdmi->bridge, NULL,
+				DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+	if (ret) {
+		dev_err(priv->dev, "Failed to attach bridge: %d\n", ret);
+		goto err_put_node;
+	}
+
+	/* Initialize & attach Bridge Connector */
+	meson_encoder_hdmi->connector = drm_bridge_connector_init(priv->drm,
+							&meson_encoder_hdmi->encoder);
+	if (IS_ERR(meson_encoder_hdmi->connector)) {
+		dev_err(priv->dev, "Unable to create HDMI bridge connector\n");
+		ret = PTR_ERR(meson_encoder_hdmi->connector);
+		goto err_put_node;
+	}
+	drm_connector_attach_encoder(meson_encoder_hdmi->connector,
+				     &meson_encoder_hdmi->encoder);
+
+	/*
+	 * We should have now in place:
+	 * encoder->[hdmi encoder bridge]->[dw-hdmi bridge]->[display connector bridge]->[display connector]
+	 */
+
+	/*
+	 * drm_connector_attach_max_bpc_property() requires the
+	 * connector to have a state.
+	 */
+	drm_atomic_helper_connector_reset(meson_encoder_hdmi->connector);
+
+	if (meson_vpu_is_compatible(priv, VPU_COMPATIBLE_GXL) ||
+	    meson_vpu_is_compatible(priv, VPU_COMPATIBLE_GXM) ||
+	    meson_vpu_is_compatible(priv, VPU_COMPATIBLE_G12A))
+		drm_connector_attach_hdr_output_metadata_property(meson_encoder_hdmi->connector);
+
+	drm_connector_attach_max_bpc_property(meson_encoder_hdmi->connector, 8, 8);
+
+	/* Handle this here until handled by drm_bridge_connector_init() */
+	meson_encoder_hdmi->connector->ycbcr_420_allowed = true;
+
+	pdev = of_find_device_by_node(remote);
+	of_node_put(remote);
+	if (pdev) {
+		struct cec_connector_info conn_info;
+		struct cec_notifier *notifier;
+
+		cec_fill_conn_info_from_drm(&conn_info, meson_encoder_hdmi->connector);
+
+		notifier = cec_notifier_conn_register(&pdev->dev, NULL, &conn_info);
+		if (!notifier) {
+			put_device(&pdev->dev);
+			return -ENOMEM;
+		}
+
+		meson_encoder_hdmi->cec_notifier = notifier;
+	}
+
+	dev_dbg(priv->dev, "HDMI encoder initialized\n");
+
+	return 0;
+
+err_put_node:
+	of_node_put(remote);
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_encoder_hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_encoder_hdmi.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2021 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#ifndef __MESON_ENCODER_HDMI_H
+#define __MESON_ENCODER_HDMI_H
+
+int meson_encoder_hdmi_init(struct meson_drm *priv);
+
+#endif /* __MESON_ENCODER_HDMI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_osd_afbcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_osd_afbcd.c
@@ -79,11 +79,6 @@
 	return meson_gxm_afbcd_pixel_fmt(modifier, format) >= 0;
 }
 
-static int meson_gxm_afbcd_init(struct meson_drm *priv)
-{
-	return 0;
-}
-
 static int meson_gxm_afbcd_reset(struct meson_drm *priv)
 {
 	writel_relaxed(VIU_SW_RESET_OSD1_AFBCD,
@@ -93,6 +88,16 @@
 	return 0;
 }
 
+static int meson_gxm_afbcd_init(struct meson_drm *priv)
+{
+	return 0;
+}
+
+static void meson_gxm_afbcd_exit(struct meson_drm *priv)
+{
+	meson_gxm_afbcd_reset(priv);
+}
+
 static int meson_gxm_afbcd_enable(struct meson_drm *priv)
 {
 	writel_relaxed(FIELD_PREP(OSD1_AFBCD_ID_FIFO_THRD, 0x40) |
@@ -172,6 +177,7 @@
 
 struct meson_afbcd_ops meson_afbcd_gxm_ops = {
 	.init = meson_gxm_afbcd_init,
+	.exit = meson_gxm_afbcd_exit,
 	.reset = meson_gxm_afbcd_reset,
 	.enable = meson_gxm_afbcd_enable,
 	.disable = meson_gxm_afbcd_disable,
@@ -269,6 +275,18 @@
 	return meson_g12a_afbcd_pixel_fmt(modifier, format) >= 0;
 }
 
+static int meson_g12a_afbcd_reset(struct meson_drm *priv)
+{
+	meson_rdma_reset(priv);
+
+	meson_rdma_writel_sync(priv, VIU_SW_RESET_G12A_AFBC_ARB |
+			       VIU_SW_RESET_G12A_OSD1_AFBCD,
+			       VIU_SW_RESET);
+	meson_rdma_writel_sync(priv, 0, VIU_SW_RESET);
+
+	return 0;
+}
+
 static int meson_g12a_afbcd_init(struct meson_drm *priv)
 {
 	int ret;
@@ -286,16 +304,10 @@
 	return 0;
 }
 
-static int meson_g12a_afbcd_reset(struct meson_drm *priv)
+static void meson_g12a_afbcd_exit(struct meson_drm *priv)
 {
-	meson_rdma_reset(priv);
-
-	meson_rdma_writel_sync(priv, VIU_SW_RESET_G12A_AFBC_ARB |
-			       VIU_SW_RESET_G12A_OSD1_AFBCD,
-			       VIU_SW_RESET);
-	meson_rdma_writel_sync(priv, 0, VIU_SW_RESET);
-
-	return 0;
+	meson_g12a_afbcd_reset(priv);
+	meson_rdma_free(priv);
 }
 
 static int meson_g12a_afbcd_enable(struct meson_drm *priv)
@@ -380,6 +392,7 @@
 
 struct meson_afbcd_ops meson_afbcd_g12a_ops = {
 	.init = meson_g12a_afbcd_init,
+	.exit = meson_g12a_afbcd_exit,
 	.reset = meson_g12a_afbcd_reset,
 	.enable = meson_g12a_afbcd_enable,
 	.disable = meson_g12a_afbcd_disable,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_osd_afbcd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_osd_afbcd.h
@@ -14,6 +14,7 @@
 
 struct meson_afbcd_ops {
 	int (*init)(struct meson_drm *priv);
+	void (*exit)(struct meson_drm *priv);
 	int (*reset)(struct meson_drm *priv);
 	int (*enable)(struct meson_drm *priv);
 	int (*disable)(struct meson_drm *priv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_plane.c
@@ -168,7 +168,7 @@
 
 	/* Enable OSD and BLK0, set max global alpha */
 	priv->viu.osd1_ctrl_stat = OSD_ENABLE |
-				   (0xFF << OSD_GLOBAL_ALPHA_SHIFT) |
+				   (0x100 << OSD_GLOBAL_ALPHA_SHIFT) |
 				   OSD_BLK0_ENABLE;
 
 	priv->viu.osd1_ctrl_stat2 = readl(priv->io_base +
@@ -533,6 +533,7 @@
 	struct meson_plane *meson_plane;
 	struct drm_plane *plane;
 	const uint64_t *format_modifiers = format_modifiers_default;
+	int ret;
 
 	meson_plane = devm_kzalloc(priv->drm->dev, sizeof(*meson_plane),
 				   GFP_KERNEL);
@@ -547,12 +548,16 @@
 	else if (meson_vpu_is_compatible(priv, VPU_COMPATIBLE_G12A))
 		format_modifiers = format_modifiers_afbc_g12a;
 
-	drm_universal_plane_init(priv->drm, plane, 0xFF,
-				 &meson_plane_funcs,
-				 supported_drm_formats,
-				 ARRAY_SIZE(supported_drm_formats),
-				 format_modifiers,
-				 DRM_PLANE_TYPE_PRIMARY, "meson_primary_plane");
+	ret = drm_universal_plane_init(priv->drm, plane, 0xFF,
+					&meson_plane_funcs,
+					supported_drm_formats,
+					ARRAY_SIZE(supported_drm_formats),
+					format_modifiers,
+					DRM_PLANE_TYPE_PRIMARY, "meson_primary_plane");
+	if (ret) {
+		devm_kfree(priv->drm->dev, meson_plane);
+		return ret;
+	}
 
 	drm_plane_helper_add(plane, &meson_plane_helper_funcs);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_vclk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_vclk.c
@@ -790,13 +790,13 @@
 				 FREQ_1000_1001(params[i].pixel_freq));
 		DRM_DEBUG_DRIVER("i = %d phy_freq = %d alt = %d\n",
 				 i, params[i].phy_freq,
-				 FREQ_1000_1001(params[i].phy_freq/10)*10);
+				 FREQ_1000_1001(params[i].phy_freq/1000)*1000);
 		/* Match strict frequency */
 		if (phy_freq == params[i].phy_freq &&
 		    vclk_freq == params[i].vclk_freq)
 			return MODE_OK;
 		/* Match 1000/1001 variant */
-		if (phy_freq == (FREQ_1000_1001(params[i].phy_freq/10)*10) &&
+		if (phy_freq == (FREQ_1000_1001(params[i].phy_freq/1000)*1000) &&
 		    vclk_freq == FREQ_1000_1001(params[i].vclk_freq))
 			return MODE_OK;
 	}
@@ -1070,7 +1070,7 @@
 
 	for (freq = 0 ; params[freq].pixel_freq ; ++freq) {
 		if ((phy_freq == params[freq].phy_freq ||
-		     phy_freq == FREQ_1000_1001(params[freq].phy_freq/10)*10) &&
+		     phy_freq == FREQ_1000_1001(params[freq].phy_freq/1000)*1000) &&
 		    (vclk_freq == params[freq].vclk_freq ||
 		     vclk_freq == FREQ_1000_1001(params[freq].vclk_freq))) {
 			if (vclk_freq != params[freq].vclk_freq)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_viu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_viu.c
@@ -94,7 +94,7 @@
 		priv->io_base + _REG(VPP_WRAP_OSD1_MATRIX_COEF11_12));
 	writel(((m[9] & 0x1fff) << 16) | (m[10] & 0x1fff),
 		priv->io_base + _REG(VPP_WRAP_OSD1_MATRIX_COEF20_21));
-	writel((m[11] & 0x1fff) << 16,
+	writel((m[11] & 0x1fff),
 		priv->io_base +	_REG(VPP_WRAP_OSD1_MATRIX_COEF22));
 
 	writel(((m[18] & 0xfff) << 16) | (m[19] & 0xfff),
@@ -436,15 +436,14 @@
 
 	/* Initialize OSD1 fifo control register */
 	reg = VIU_OSD_DDR_PRIORITY_URGENT |
-		VIU_OSD_HOLD_FIFO_LINES(31) |
 		VIU_OSD_FIFO_DEPTH_VAL(32) | /* fifo_depth_val: 32*8=256 */
 		VIU_OSD_WORDS_PER_BURST(4) | /* 4 words in 1 burst */
 		VIU_OSD_FIFO_LIMITS(2);      /* fifo_lim: 2*16=32 */
 
 	if (meson_vpu_is_compatible(priv, VPU_COMPATIBLE_G12A))
-		reg |= VIU_OSD_BURST_LENGTH_32;
+		reg |= (VIU_OSD_BURST_LENGTH_32 | VIU_OSD_HOLD_FIFO_LINES(31));
 	else
-		reg |= VIU_OSD_BURST_LENGTH_64;
+		reg |= (VIU_OSD_BURST_LENGTH_64 | VIU_OSD_HOLD_FIFO_LINES(4));
 
 	writel_relaxed(reg, priv->io_base + _REG(VIU_OSD1_FIFO_CTRL_STAT));
 	writel_relaxed(reg, priv->io_base + _REG(VIU_OSD2_FIFO_CTRL_STAT));
@@ -469,17 +468,17 @@
 			priv->io_base + _REG(VD2_IF0_LUMA_FIFO_SIZE));
 
 	if (meson_vpu_is_compatible(priv, VPU_COMPATIBLE_G12A)) {
-		writel_relaxed(VIU_OSD_BLEND_REORDER(0, 1) |
-			       VIU_OSD_BLEND_REORDER(1, 0) |
-			       VIU_OSD_BLEND_REORDER(2, 0) |
-			       VIU_OSD_BLEND_REORDER(3, 0) |
-			       VIU_OSD_BLEND_DIN_EN(1) |
-			       VIU_OSD_BLEND1_DIN3_BYPASS_TO_DOUT1 |
-			       VIU_OSD_BLEND1_DOUT_BYPASS_TO_BLEND2 |
-			       VIU_OSD_BLEND_DIN0_BYPASS_TO_DOUT0 |
-			       VIU_OSD_BLEND_BLEN2_PREMULT_EN(1) |
-			       VIU_OSD_BLEND_HOLD_LINES(4),
-			       priv->io_base + _REG(VIU_OSD_BLEND_CTRL));
+		u32 val = (u32)VIU_OSD_BLEND_REORDER(0, 1) |
+			  (u32)VIU_OSD_BLEND_REORDER(1, 0) |
+			  (u32)VIU_OSD_BLEND_REORDER(2, 0) |
+			  (u32)VIU_OSD_BLEND_REORDER(3, 0) |
+			  (u32)VIU_OSD_BLEND_DIN_EN(1) |
+			  (u32)VIU_OSD_BLEND1_DIN3_BYPASS_TO_DOUT1 |
+			  (u32)VIU_OSD_BLEND1_DOUT_BYPASS_TO_BLEND2 |
+			  (u32)VIU_OSD_BLEND_DIN0_BYPASS_TO_DOUT0 |
+			  (u32)VIU_OSD_BLEND_BLEN2_PREMULT_EN(1) |
+			  (u32)VIU_OSD_BLEND_HOLD_LINES(4);
+		writel_relaxed(val, priv->io_base + _REG(VIU_OSD_BLEND_CTRL));
 
 		writel_relaxed(OSD_BLEND_PATH_SEL_ENABLE,
 			       priv->io_base + _REG(OSD1_BLEND_SRC_CTRL));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/meson/meson_vpp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/meson/meson_vpp.c
@@ -100,6 +100,8 @@
 			       priv->io_base + _REG(VPP_DOLBY_CTRL));
 		writel_relaxed(0x1020080,
 				priv->io_base + _REG(VPP_DUMMY_DATA1));
+		writel_relaxed(0x42020,
+				priv->io_base + _REG(VPP_DUMMY_DATA));
 	} else if (meson_vpu_is_compatible(priv, VPU_COMPATIBLE_G12A))
 		writel_relaxed(0xf, priv->io_base + _REG(DOLBY_PATH_CTRL));
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mgag200/mgag200_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mgag200/mgag200_i2c.c
@@ -134,7 +134,7 @@
 	i2c->adapter.algo_data = &i2c->bit;
 
 	i2c->bit.udelay = 10;
-	i2c->bit.timeout = 2;
+	i2c->bit.timeout = usecs_to_jiffies(2200);
 	i2c->bit.data = i2c;
 	i2c->bit.setsda		= mga_gpio_setsda;
 	i2c->bit.setscl		= mga_gpio_setscl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mgag200/mgag200_mode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mgag200/mgag200_mode.c
@@ -529,7 +529,10 @@
 	WREG_GFX(3, 0x00);
 	WREG_GFX(4, 0x00);
 	WREG_GFX(5, 0x40);
-	WREG_GFX(6, 0x05);
+	/* GCTL6 should be 0x05, but we configure memmapsl to 0xb8000 (text mode),
+	 * so that it doesn't hang when running kexec/kdump on G200_SE rev42.
+	 */
+	WREG_GFX(6, 0x0d);
 	WREG_GFX(7, 0x0f);
 	WREG_GFX(8, 0x0f);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mgag200/mgag200_pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mgag200/mgag200_pll.c
@@ -268,7 +268,8 @@
 	pixpllcp = pixpllc->p - 1;
 	pixpllcs = pixpllc->s;
 
-	xpixpllcm = pixpllcm | ((pixpllcn & BIT(8)) >> 1);
+	// For G200SE A, BIT(7) should be set unconditionally.
+	xpixpllcm = BIT(7) | pixpllcm;
 	xpixpllcn = pixpllcn;
 	xpixpllcp = (pixpllcs << 3) | pixpllcp;
 
@@ -404,9 +405,9 @@
 		udelay(50);
 
 		/* program pixel pll register */
-		WREG_DAC(MGA1064_PIX_PLLC_N, xpixpllcn);
-		WREG_DAC(MGA1064_PIX_PLLC_M, xpixpllcm);
-		WREG_DAC(MGA1064_PIX_PLLC_P, xpixpllcp);
+		WREG_DAC(MGA1064_WB_PIX_PLLC_N, xpixpllcn);
+		WREG_DAC(MGA1064_WB_PIX_PLLC_M, xpixpllcm);
+		WREG_DAC(MGA1064_WB_PIX_PLLC_P, xpixpllcp);
 
 		udelay(50);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/Kconfig
@@ -63,6 +63,7 @@
 config DRM_MSM_DP
 	bool "Enable DisplayPort support in MSM DRM driver"
 	depends on DRM_MSM
+	select RATIONAL
 	default y
 	help
 	  Compile in support for DP driver in MSM DRM driver. DP external
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/Makefile
@@ -19,7 +19,7 @@
 	hdmi/hdmi.o \
 	hdmi/hdmi_audio.o \
 	hdmi/hdmi_bridge.o \
-	hdmi/hdmi_connector.o \
+	hdmi/hdmi_hpd.o \
 	hdmi/hdmi_i2c.o \
 	hdmi/hdmi_phy.o \
 	hdmi/hdmi_phy_8960.o \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a2xx_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a2xx_gpu.c
@@ -12,7 +12,6 @@
 
 static void a2xx_submit(struct msm_gpu *gpu, struct msm_gem_submit *submit)
 {
-	struct msm_drm_private *priv = gpu->dev->dev_private;
 	struct msm_ringbuffer *ring = submit->ring;
 	unsigned int i;
 
@@ -23,7 +22,7 @@
 			break;
 		case MSM_SUBMIT_CMD_CTX_RESTORE_BUF:
 			/* ignore if there has not been a ctx switch: */
-			if (priv->lastctx == submit->queue->ctx)
+			if (gpu->cur_ctx_seqno == submit->queue->ctx->seqno)
 				break;
 			fallthrough;
 		case MSM_SUBMIT_CMD_BUF:
@@ -521,6 +520,10 @@
 	gpu->perfcntrs = perfcntrs;
 	gpu->num_perfcntrs = ARRAY_SIZE(perfcntrs);
 
+	ret = adreno_gpu_init(dev, pdev, adreno_gpu, &funcs, 1);
+	if (ret)
+		goto fail;
+
 	if (adreno_is_a20x(adreno_gpu))
 		adreno_gpu->registers = a200_registers;
 	else if (adreno_is_a225(adreno_gpu))
@@ -528,10 +531,6 @@
 	else
 		adreno_gpu->registers = a220_registers;
 
-	ret = adreno_gpu_init(dev, pdev, adreno_gpu, &funcs, 1);
-	if (ret)
-		goto fail;
-
 	if (!gpu->aspace) {
 		dev_err(dev->dev, "No memory protection without MMU\n");
 		if (!allow_vram_carveout) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a3xx_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a3xx_gpu.c
@@ -30,7 +30,6 @@
 
 static void a3xx_submit(struct msm_gpu *gpu, struct msm_gem_submit *submit)
 {
-	struct msm_drm_private *priv = gpu->dev->dev_private;
 	struct msm_ringbuffer *ring = submit->ring;
 	unsigned int i;
 
@@ -41,7 +40,7 @@
 			break;
 		case MSM_SUBMIT_CMD_CTX_RESTORE_BUF:
 			/* ignore if there has not been a ctx switch: */
-			if (priv->lastctx == submit->queue->ctx)
+			if (gpu->cur_ctx_seqno == submit->queue->ctx->seqno)
 				break;
 			fallthrough;
 		case MSM_SUBMIT_CMD_BUF:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a4xx_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a4xx_gpu.c
@@ -24,7 +24,6 @@
 
 static void a4xx_submit(struct msm_gpu *gpu, struct msm_gem_submit *submit)
 {
-	struct msm_drm_private *priv = gpu->dev->dev_private;
 	struct msm_ringbuffer *ring = submit->ring;
 	unsigned int i;
 
@@ -35,7 +34,7 @@
 			break;
 		case MSM_SUBMIT_CMD_CTX_RESTORE_BUF:
 			/* ignore if there has not been a ctx switch: */
-			if (priv->lastctx == submit->queue->ctx)
+			if (gpu->cur_ctx_seqno == submit->queue->ctx->seqno)
 				break;
 			fallthrough;
 		case MSM_SUBMIT_CMD_BUF:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a5xx_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a5xx_debugfs.c
@@ -107,7 +107,7 @@
 	 * try to reset an active GPU.
 	 */
 
-	mutex_lock(&dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 
 	release_firmware(adreno_gpu->fw[ADRENO_FW_PM4]);
 	adreno_gpu->fw[ADRENO_FW_PM4] = NULL;
@@ -133,7 +133,7 @@
 	gpu->funcs->recover(gpu);
 
 	pm_runtime_put_sync(&gpu->pdev->dev);
-	mutex_unlock(&dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a5xx_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a5xx_gpu.c
@@ -65,7 +65,8 @@
 
 static void a5xx_submit_in_rb(struct msm_gpu *gpu, struct msm_gem_submit *submit)
 {
-	struct msm_drm_private *priv = gpu->dev->dev_private;
+	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
+	struct a5xx_gpu *a5xx_gpu = to_a5xx_gpu(adreno_gpu);
 	struct msm_ringbuffer *ring = submit->ring;
 	struct msm_gem_object *obj;
 	uint32_t *ptr, dwords;
@@ -76,7 +77,7 @@
 		case MSM_SUBMIT_CMD_IB_TARGET_BUF:
 			break;
 		case MSM_SUBMIT_CMD_CTX_RESTORE_BUF:
-			if (priv->lastctx == submit->queue->ctx)
+			if (gpu->cur_ctx_seqno == submit->queue->ctx->seqno)
 				break;
 			fallthrough;
 		case MSM_SUBMIT_CMD_BUF:
@@ -90,7 +91,7 @@
 			 * since we've already mapped it once in
 			 * submit_reloc()
 			 */
-			if (WARN_ON(!ptr))
+			if (WARN_ON(IS_ERR_OR_NULL(ptr)))
 				return;
 
 			for (i = 0; i < dwords; i++) {
@@ -110,6 +111,7 @@
 		}
 	}
 
+	a5xx_gpu->last_seqno[ring->id] = submit->seqno;
 	a5xx_flush(gpu, ring, true);
 	a5xx_preempt_trigger(gpu);
 
@@ -126,12 +128,11 @@
 {
 	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
 	struct a5xx_gpu *a5xx_gpu = to_a5xx_gpu(adreno_gpu);
-	struct msm_drm_private *priv = gpu->dev->dev_private;
 	struct msm_ringbuffer *ring = submit->ring;
 	unsigned int i, ibs = 0;
 
 	if (IS_ENABLED(CONFIG_DRM_MSM_GPU_SUDO) && submit->in_rb) {
-		priv->lastctx = NULL;
+		gpu->cur_ctx_seqno = 0;
 		a5xx_submit_in_rb(gpu, submit);
 		return;
 	}
@@ -152,9 +153,13 @@
 	OUT_PKT7(ring, CP_SET_PROTECTED_MODE, 1);
 	OUT_RING(ring, 1);
 
-	/* Enable local preemption for finegrain preemption */
-	OUT_PKT7(ring, CP_PREEMPT_ENABLE_GLOBAL, 1);
-	OUT_RING(ring, 0x02);
+	/*
+	 * Disable local preemption by default because it requires
+	 * user-space to be aware of it and provide additional handling
+	 * to restore rendering state or do various flushes on switch.
+	 */
+	OUT_PKT7(ring, CP_PREEMPT_ENABLE_LOCAL, 1);
+	OUT_RING(ring, 0x0);
 
 	/* Allow CP_CONTEXT_SWITCH_YIELD packets in the IB2 */
 	OUT_PKT7(ring, CP_YIELD_ENABLE, 1);
@@ -166,7 +171,7 @@
 		case MSM_SUBMIT_CMD_IB_TARGET_BUF:
 			break;
 		case MSM_SUBMIT_CMD_CTX_RESTORE_BUF:
-			if (priv->lastctx == submit->queue->ctx)
+			if (gpu->cur_ctx_seqno == submit->queue->ctx->seqno)
 				break;
 			fallthrough;
 		case MSM_SUBMIT_CMD_BUF:
@@ -208,6 +213,7 @@
 	/* Write the fence to the scratch register */
 	OUT_PKT4(ring, REG_A5XX_CP_SCRATCH_REG(2), 1);
 	OUT_RING(ring, submit->seqno);
+	a5xx_gpu->last_seqno[ring->id] = submit->seqno;
 
 	/*
 	 * Execute a CACHE_FLUSH_TS event. This will ensure that the
@@ -801,7 +807,7 @@
 	gpu_write(gpu, REG_A5XX_RBBM_AHB_CNTL2, 0x0000003F);
 
 	/* Set the highest bank bit */
-	if (adreno_is_a540(adreno_gpu))
+	if (adreno_is_a540(adreno_gpu) || adreno_is_a530(adreno_gpu))
 		regbit = 2;
 	else
 		regbit = 1;
@@ -1746,9 +1752,11 @@
 {
 	struct msm_drm_private *priv = dev->dev_private;
 	struct platform_device *pdev = priv->gpu_pdev;
+	struct adreno_platform_config *config = pdev->dev.platform_data;
 	struct a5xx_gpu *a5xx_gpu = NULL;
 	struct adreno_gpu *adreno_gpu;
 	struct msm_gpu *gpu;
+	unsigned int nr_rings;
 	int ret;
 
 	if (!pdev) {
@@ -1769,7 +1777,12 @@
 
 	check_speed_bin(&pdev->dev);
 
-	ret = adreno_gpu_init(dev, pdev, adreno_gpu, &funcs, 4);
+	nr_rings = 4;
+
+	if (adreno_cmp_rev(ADRENO_REV(5, 1, 0, ANY_ID), config->rev))
+		nr_rings = 1;
+
+	ret = adreno_gpu_init(dev, pdev, adreno_gpu, &funcs, nr_rings);
 	if (ret) {
 		a5xx_destroy(&(a5xx_gpu->base.base));
 		return ERR_PTR(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a5xx_gpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a5xx_gpu.h
@@ -34,8 +34,10 @@
 	struct drm_gem_object *preempt_counters_bo[MSM_GPU_MAX_RINGS];
 	struct a5xx_preempt_record *preempt[MSM_GPU_MAX_RINGS];
 	uint64_t preempt_iova[MSM_GPU_MAX_RINGS];
+	uint32_t last_seqno[MSM_GPU_MAX_RINGS];
 
 	atomic_t preempt_state;
+	spinlock_t preempt_start_lock;
 	struct timer_list preempt_timer;
 
 	struct drm_gem_object *shadow_bo;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a5xx_preempt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a5xx_preempt.c
@@ -55,6 +55,8 @@
 /* Return the highest priority ringbuffer with something in it */
 static struct msm_ringbuffer *get_next_ring(struct msm_gpu *gpu)
 {
+	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
+	struct a5xx_gpu *a5xx_gpu = to_a5xx_gpu(adreno_gpu);
 	unsigned long flags;
 	int i;
 
@@ -63,7 +65,9 @@
 		struct msm_ringbuffer *ring = gpu->rb[i];
 
 		spin_lock_irqsave(&ring->preempt_lock, flags);
-		empty = (get_wptr(ring) == ring->memptrs->rptr);
+		empty = (get_wptr(ring) == gpu->funcs->get_rptr(gpu, ring));
+		if (!empty && ring == a5xx_gpu->cur_ring)
+			empty = ring->memptrs->fence == a5xx_gpu->last_seqno[i];
 		spin_unlock_irqrestore(&ring->preempt_lock, flags);
 
 		if (!empty)
@@ -98,11 +102,18 @@
 		return;
 
 	/*
+	 * Serialize preemption start to ensure that we always make
+	 * decision on latest state. Otherwise we can get stuck in
+	 * lower priority or empty ring.
+	 */
+	spin_lock_irqsave(&a5xx_gpu->preempt_start_lock, flags);
+
+	/*
 	 * Try to start preemption by moving from NONE to START. If
 	 * unsuccessful, a preemption is already in flight
 	 */
 	if (!try_preempt_state(a5xx_gpu, PREEMPT_NONE, PREEMPT_START))
-		return;
+		goto out;
 
 	/* Get the next ring to preempt to */
 	ring = get_next_ring(gpu);
@@ -127,9 +138,11 @@
 		set_preempt_state(a5xx_gpu, PREEMPT_ABORT);
 		update_wptr(gpu, a5xx_gpu->cur_ring);
 		set_preempt_state(a5xx_gpu, PREEMPT_NONE);
-		return;
+		goto out;
 	}
 
+	spin_unlock_irqrestore(&a5xx_gpu->preempt_start_lock, flags);
+
 	/* Make sure the wptr doesn't update while we're in motion */
 	spin_lock_irqsave(&ring->preempt_lock, flags);
 	a5xx_gpu->preempt[ring->id]->wptr = get_wptr(ring);
@@ -153,6 +166,10 @@
 
 	/* And actually start the preemption */
 	gpu_write(gpu, REG_A5XX_CP_CONTEXT_SWITCH_CNTL, 1);
+	return;
+
+out:
+	spin_unlock_irqrestore(&a5xx_gpu->preempt_start_lock, flags);
 }
 
 void a5xx_preempt_irq(struct msm_gpu *gpu)
@@ -189,6 +206,12 @@
 	update_wptr(gpu, a5xx_gpu->cur_ring);
 
 	set_preempt_state(a5xx_gpu, PREEMPT_NONE);
+
+	/*
+	 * Try to trigger preemption again in case there was a submit or
+	 * retire during ring switch
+	 */
+	a5xx_preempt_trigger(gpu);
 }
 
 void a5xx_preempt_hw_init(struct msm_gpu *gpu)
@@ -205,9 +228,12 @@
 		return;
 
 	for (i = 0; i < gpu->nr_rings; i++) {
+		a5xx_gpu->preempt[i]->data = 0;
+		a5xx_gpu->preempt[i]->info = 0;
 		a5xx_gpu->preempt[i]->wptr = 0;
 		a5xx_gpu->preempt[i]->rptr = 0;
 		a5xx_gpu->preempt[i]->rbase = gpu->rb[i]->iova;
+		a5xx_gpu->preempt[i]->rptr_addr = shadowptr(a5xx_gpu, gpu->rb[i]);
 	}
 
 	/* Write a 0 to signal that we aren't switching pagetables */
@@ -259,7 +285,6 @@
 	ptr->data = 0;
 	ptr->cntl = MSM_GPU_RB_CNTL_DEFAULT | AXXX_CP_RB_CNTL_NO_UPDATE;
 
-	ptr->rptr_addr = shadowptr(a5xx_gpu, ring);
 	ptr->counter = counters_iova;
 
 	return 0;
@@ -300,5 +325,6 @@
 		}
 	}
 
+	spin_lock_init(&a5xx_gpu->preempt_start_lock);
 	timer_setup(&a5xx_gpu->preempt_timer, a5xx_preempt_timer, 0);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a6xx_gmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a6xx_gmu.c
@@ -516,11 +516,11 @@
 	struct adreno_gpu *adreno_gpu = &a6xx_gpu->base;
 	struct platform_device *pdev = to_platform_device(gmu->dev);
 	void __iomem *pdcptr = a6xx_gmu_get_mmio(pdev, "gmu_pdc");
-	void __iomem *seqptr;
+	void __iomem *seqptr = NULL;
 	uint32_t pdc_address_offset;
 	bool pdc_in_aop = false;
 
-	if (!pdcptr)
+	if (IS_ERR(pdcptr))
 		goto err;
 
 	if (adreno_is_a650(adreno_gpu) || adreno_is_a660_family(adreno_gpu))
@@ -532,7 +532,7 @@
 
 	if (!pdc_in_aop) {
 		seqptr = a6xx_gmu_get_mmio(pdev, "gmu_pdc_seq");
-		if (!seqptr)
+		if (IS_ERR(seqptr))
 			goto err;
 	}
 
@@ -1432,15 +1432,13 @@
 
 	irq = platform_get_irq_byname(pdev, name);
 
-	ret = request_irq(irq, handler, IRQF_TRIGGER_HIGH, name, gmu);
+	ret = request_irq(irq, handler, IRQF_TRIGGER_HIGH | IRQF_NO_AUTOEN, name, gmu);
 	if (ret) {
 		DRM_DEV_ERROR(&pdev->dev, "Unable to get interrupt %s %d\n",
 			      name, ret);
 		return ret;
 	}
 
-	disable_irq(irq);
-
 	return irq;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
@@ -106,7 +106,7 @@
 	u32 asid;
 	u64 memptr = rbmemptr(ring, ttbr0);
 
-	if (ctx->seqno == a6xx_gpu->cur_ctx_seqno)
+	if (ctx->seqno == a6xx_gpu->base.base.cur_ctx_seqno)
 		return;
 
 	if (msm_iommu_pagetable_params(ctx->aspace->mmu, &ttbr, &asid))
@@ -138,14 +138,11 @@
 
 	OUT_PKT7(ring, CP_EVENT_WRITE, 1);
 	OUT_RING(ring, 0x31);
-
-	a6xx_gpu->cur_ctx_seqno = ctx->seqno;
 }
 
 static void a6xx_submit(struct msm_gpu *gpu, struct msm_gem_submit *submit)
 {
 	unsigned int index = submit->seqno % MSM_GPU_SUBMIT_STATS_COUNT;
-	struct msm_drm_private *priv = gpu->dev->dev_private;
 	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
 	struct a6xx_gpu *a6xx_gpu = to_a6xx_gpu(adreno_gpu);
 	struct msm_ringbuffer *ring = submit->ring;
@@ -177,7 +174,7 @@
 		case MSM_SUBMIT_CMD_IB_TARGET_BUF:
 			break;
 		case MSM_SUBMIT_CMD_CTX_RESTORE_BUF:
-			if (priv->lastctx == submit->queue->ctx)
+			if (gpu->cur_ctx_seqno == submit->queue->ctx->seqno)
 				break;
 			fallthrough;
 		case MSM_SUBMIT_CMD_BUF:
@@ -658,19 +655,23 @@
 {
 	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
 	const u32 *regs = a6xx_protect;
-	unsigned i, count = ARRAY_SIZE(a6xx_protect), count_max = 32;
-
-	BUILD_BUG_ON(ARRAY_SIZE(a6xx_protect) > 32);
-	BUILD_BUG_ON(ARRAY_SIZE(a650_protect) > 48);
+	unsigned i, count, count_max;
 
 	if (adreno_is_a650(adreno_gpu)) {
 		regs = a650_protect;
 		count = ARRAY_SIZE(a650_protect);
 		count_max = 48;
+		BUILD_BUG_ON(ARRAY_SIZE(a650_protect) > 48);
 	} else if (adreno_is_a660_family(adreno_gpu)) {
 		regs = a660_protect;
 		count = ARRAY_SIZE(a660_protect);
 		count_max = 48;
+		BUILD_BUG_ON(ARRAY_SIZE(a660_protect) > 48);
+	} else {
+		regs = a6xx_protect;
+		count = ARRAY_SIZE(a6xx_protect);
+		count_max = 32;
+		BUILD_BUG_ON(ARRAY_SIZE(a6xx_protect) > 32);
 	}
 
 	/*
@@ -1081,7 +1082,7 @@
 	/* Always come up on rb 0 */
 	a6xx_gpu->cur_ring = gpu->rb[0];
 
-	a6xx_gpu->cur_ctx_seqno = 0;
+	gpu->cur_ctx_seqno = 0;
 
 	/* Enable the SQE_to start the CP engine */
 	gpu_write(gpu, REG_A6XX_CP_SQE_CNTL, 1);
@@ -1424,17 +1425,24 @@
 {
 	struct adreno_gpu *adreno_gpu = &a6xx_gpu->base;
 	struct msm_gpu *gpu = &adreno_gpu->base;
-	u32 gpu_scid, cntl1_regval = 0;
+	u32 cntl1_regval = 0;
 
 	if (IS_ERR(a6xx_gpu->llc_mmio))
 		return;
 
 	if (!llcc_slice_activate(a6xx_gpu->llc_slice)) {
-		gpu_scid = llcc_get_slice_id(a6xx_gpu->llc_slice);
+		u32 gpu_scid = llcc_get_slice_id(a6xx_gpu->llc_slice);
 
 		gpu_scid &= 0x1f;
 		cntl1_regval = (gpu_scid << 0) | (gpu_scid << 5) | (gpu_scid << 10) |
 			       (gpu_scid << 15) | (gpu_scid << 20);
+
+		/* On A660, the SCID programming for UCHE traffic is done in
+		 * A6XX_GBIF_SCACHE_CNTL0[14:10]
+		 */
+		if (adreno_is_a660_family(adreno_gpu))
+			gpu_rmw(gpu, REG_A6XX_GBIF_SCACHE_CNTL0, (0x1f << 10) |
+				(1 << 8), (gpu_scid << 10) | (1 << 8));
 	}
 
 	/*
@@ -1471,13 +1479,6 @@
 	}
 
 	gpu_rmw(gpu, REG_A6XX_GBIF_SCACHE_CNTL1, GENMASK(24, 0), cntl1_regval);
-
-	/* On A660, the SCID programming for UCHE traffic is done in
-	 * A6XX_GBIF_SCACHE_CNTL0[14:10]
-	 */
-	if (adreno_is_a660_family(adreno_gpu))
-		gpu_rmw(gpu, REG_A6XX_GBIF_SCACHE_CNTL0, (0x1f << 10) |
-			(1 << 8), (gpu_scid << 10) | (1 << 8));
 }
 
 static void a6xx_llc_slices_destroy(struct a6xx_gpu *a6xx_gpu)
@@ -1557,6 +1558,8 @@
 		for (i = 0; i < gpu->nr_rings; i++)
 			a6xx_gpu->shadow[i] = 0;
 
+	gpu->suspend_count++;
+
 	return 0;
 }
 
@@ -1705,7 +1708,7 @@
 		return ERR_CAST(mmu);
 
 	return msm_gem_address_space_create(mmu,
-		"gpu", 0x100000000ULL, 0x1ffffffffULL);
+		"gpu", 0x100000000ULL, SZ_4G);
 }
 
 static uint32_t a6xx_get_rptr(struct msm_gpu *gpu, struct msm_ringbuffer *ring)
@@ -1740,7 +1743,7 @@
 
 	if (val == UINT_MAX) {
 		DRM_DEV_ERROR(dev,
-			"missing support for speed-bin: %u. Some OPPs may not be supported by hardware",
+			"missing support for speed-bin: %u. Some OPPs may not be supported by hardware\n",
 			fuse);
 		return UINT_MAX;
 	}
@@ -1750,7 +1753,7 @@
 
 static int a6xx_set_supported_hw(struct device *dev, struct adreno_rev rev)
 {
-	u32 supp_hw = UINT_MAX;
+	u32 supp_hw;
 	u32 speedbin;
 	int ret;
 
@@ -1762,15 +1765,13 @@
 	if (ret == -ENOENT) {
 		return 0;
 	} else if (ret) {
-		DRM_DEV_ERROR(dev,
-			      "failed to read speed-bin (%d). Some OPPs may not be supported by hardware",
-			      ret);
-		goto done;
+		dev_err_probe(dev, ret,
+			      "failed to read speed-bin. Some OPPs may not be supported by hardware\n");
+		return ret;
 	}
 
 	supp_hw = fuse_to_supp_hw(dev, rev, speedbin);
 
-done:
 	ret = devm_pm_opp_set_supported_hw(dev, &supp_hw, 1);
 	if (ret)
 		return ret;
@@ -1866,6 +1867,7 @@
 	BUG_ON(!node);
 
 	ret = a6xx_gmu_init(a6xx_gpu, node);
+	of_node_put(node);
 	if (ret) {
 		a6xx_destroy(&(a6xx_gpu->base.base));
 		return ERR_PTR(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a6xx_gpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a6xx_gpu.h
@@ -20,16 +20,6 @@
 
 	struct msm_ringbuffer *cur_ring;
 
-	/**
-	 * cur_ctx_seqno:
-	 *
-	 * The ctx->seqno value of the context with current pgtables
-	 * installed.  Tracked by seqno rather than pointer value to
-	 * avoid dangling pointers, and cases where a ctx can be freed
-	 * and a new one created with the same address.
-	 */
-	int cur_ctx_seqno;
-
 	struct a6xx_gmu gmu;
 
 	struct drm_gem_object *shadow_bo;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c
@@ -777,12 +777,12 @@
 	struct a6xx_gpu *a6xx_gpu = to_a6xx_gpu(adreno_gpu);
 
 	a6xx_state->gmu_registers = state_kcalloc(a6xx_state,
-		2, sizeof(*a6xx_state->gmu_registers));
+		3, sizeof(*a6xx_state->gmu_registers));
 
 	if (!a6xx_state->gmu_registers)
 		return;
 
-	a6xx_state->nr_gmu_registers = 2;
+	a6xx_state->nr_gmu_registers = 3;
 
 	/* Get the CX GMU registers from AHB */
 	_a6xx_get_gmu_registers(gpu, a6xx_state, &a6xx_gmu_reglist[0],
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/a6xx_gpu_state.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/a6xx_gpu_state.h
@@ -200,7 +200,7 @@
 	SHADER(A6XX_SP_LB_3_DATA, 0x800),
 	SHADER(A6XX_SP_LB_4_DATA, 0x800),
 	SHADER(A6XX_SP_LB_5_DATA, 0x200),
-	SHADER(A6XX_SP_CB_BINDLESS_DATA, 0x2000),
+	SHADER(A6XX_SP_CB_BINDLESS_DATA, 0x800),
 	SHADER(A6XX_SP_CB_LEGACY_DATA, 0x280),
 	SHADER(A6XX_SP_UAV_DATA, 0x80),
 	SHADER(A6XX_SP_INST_TAG, 0x80),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/adreno_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/adreno_device.c
@@ -398,25 +398,29 @@
 	if (ret)
 		return NULL;
 
-	/* Make sure pm runtime is active and reset any previous errors */
-	pm_runtime_set_active(&pdev->dev);
+	/*
+	 * Now that we have firmware loaded, and are ready to begin
+	 * booting the gpu, go ahead and enable runpm:
+	 */
+	pm_runtime_enable(&pdev->dev);
 
 	ret = pm_runtime_get_sync(&pdev->dev);
 	if (ret < 0) {
-		pm_runtime_put_sync(&pdev->dev);
+		pm_runtime_put_noidle(&pdev->dev);
 		DRM_DEV_ERROR(dev->dev, "Couldn't power up the GPU: %d\n", ret);
-		return NULL;
+		goto err_disable_rpm;
 	}
 
-	mutex_lock(&dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 	ret = msm_gpu_hw_init(gpu);
-	mutex_unlock(&dev->struct_mutex);
-	pm_runtime_put_autosuspend(&pdev->dev);
+	mutex_unlock(&gpu->lock);
 	if (ret) {
 		DRM_DEV_ERROR(dev->dev, "gpu hw init failed: %d\n", ret);
-		return NULL;
+		goto err_put_rpm;
 	}
 
+	pm_runtime_put_autosuspend(&pdev->dev);
+
 #ifdef CONFIG_DEBUG_FS
 	if (gpu->funcs->debugfs_init) {
 		gpu->funcs->debugfs_init(gpu, dev->primary);
@@ -425,6 +429,13 @@
 #endif
 
 	return gpu;
+
+err_put_rpm:
+	pm_runtime_put_sync_suspend(&pdev->dev);
+err_disable_rpm:
+	pm_runtime_disable(&pdev->dev);
+
+	return NULL;
 }
 
 static void set_gpu_pdev(struct drm_device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/adreno_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/adreno_gpu.c
@@ -94,7 +94,7 @@
 		 * was a bad idea, and is only provided for backwards
 		 * compatibility for older targets.
 		 */
-		return -ENODEV;
+		return -ENOENT;
 	}
 
 	if (IS_ERR(fw)) {
@@ -321,7 +321,7 @@
 		ret = request_firmware_direct(&fw, fwname, drm->dev);
 		if (!ret) {
 			DRM_DEV_INFO(drm->dev, "loaded %s from legacy location\n",
-				newname);
+				fwname);
 			adreno_gpu->fwloc = FW_LOCATION_LEGACY;
 			goto out;
 		} else if (adreno_gpu->fwloc != FW_LOCATION_UNKNOWN) {
@@ -943,7 +943,6 @@
 	pm_runtime_set_autosuspend_delay(dev,
 		adreno_gpu->info->inactive_period);
 	pm_runtime_use_autosuspend(dev);
-	pm_runtime_enable(dev);
 
 	return msm_gpu_init(drm, pdev, &adreno_gpu->base, &funcs->base,
 			adreno_gpu->info->name, &adreno_gpu_config);
@@ -952,13 +951,14 @@
 void adreno_gpu_cleanup(struct adreno_gpu *adreno_gpu)
 {
 	struct msm_gpu *gpu = &adreno_gpu->base;
-	struct msm_drm_private *priv = gpu->dev->dev_private;
+	struct msm_drm_private *priv = gpu->dev ? gpu->dev->dev_private : NULL;
 	unsigned int i;
 
 	for (i = 0; i < ARRAY_SIZE(adreno_gpu->info->fw); i++)
 		release_firmware(adreno_gpu->fw[i]);
 
-	pm_runtime_disable(&priv->gpu_pdev->dev);
+	if (priv && pm_runtime_enabled(&priv->gpu_pdev->dev))
+		pm_runtime_disable(&priv->gpu_pdev->dev);
 
 	msm_gpu_cleanup(&adreno_gpu->base);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/adreno/adreno_gpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/adreno/adreno_gpu.h
@@ -29,11 +29,9 @@
 	ADRENO_FW_MAX,
 };
 
-enum adreno_quirks {
-	ADRENO_QUIRK_TWO_PASS_USE_WFI = 1,
-	ADRENO_QUIRK_FAULT_DETECT_MASK = 2,
-	ADRENO_QUIRK_LMLOADKILL_DISABLE = 3,
-};
+#define ADRENO_QUIRK_TWO_PASS_USE_WFI		BIT(0)
+#define ADRENO_QUIRK_FAULT_DETECT_MASK		BIT(1)
+#define ADRENO_QUIRK_LMLOADKILL_DISABLE		BIT(2)
 
 struct adreno_rev {
 	uint8_t  core;
@@ -65,7 +63,7 @@
 	const char *name;
 	const char *fw[ADRENO_FW_MAX];
 	uint32_t gmem;
-	enum adreno_quirks quirks;
+	u64 quirks;
 	struct msm_gpu *(*init)(struct drm_device *dev);
 	const char *zapfw;
 	u32 inactive_period;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
@@ -80,7 +80,7 @@
 
 	mode = &state->adjusted_mode;
 
-	crtc_clk = mode->vtotal * mode->hdisplay * drm_mode_vrefresh(mode);
+	crtc_clk = (u64)mode->vtotal * mode->hdisplay * drm_mode_vrefresh(mode);
 
 	drm_atomic_crtc_for_each_plane(plane, crtc) {
 		pstate = to_dpu_plane_state(plane->state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
@@ -15,19 +15,6 @@
 #define	DPU_PERF_DEFAULT_MAX_CORE_CLK_RATE	412500000
 
 /**
- * enum dpu_core_perf_data_bus_id - data bus identifier
- * @DPU_CORE_PERF_DATA_BUS_ID_MNOC: DPU/MNOC data bus
- * @DPU_CORE_PERF_DATA_BUS_ID_LLCC: MNOC/LLCC data bus
- * @DPU_CORE_PERF_DATA_BUS_ID_EBI: LLCC/EBI data bus
- */
-enum dpu_core_perf_data_bus_id {
-	DPU_CORE_PERF_DATA_BUS_ID_MNOC,
-	DPU_CORE_PERF_DATA_BUS_ID_LLCC,
-	DPU_CORE_PERF_DATA_BUS_ID_EBI,
-	DPU_CORE_PERF_DATA_BUS_ID_MAX,
-};
-
-/**
  * struct dpu_core_perf_params - definition of performance parameters
  * @max_per_pipe_ib: maximum instantaneous bandwidth request
  * @bw_ctl: arbitrated bandwidth request
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
@@ -230,6 +230,9 @@
 		if (!state)
 			continue;
 
+		if (!state->visible)
+			continue;
+
 		pstate = to_dpu_plane_state(state);
 		fb = state->fb;
 
@@ -767,7 +770,10 @@
 	if (crtc->state)
 		dpu_crtc_destroy_state(crtc, crtc->state);
 
-	__drm_atomic_helper_crtc_reset(crtc, &cstate->base);
+	if (cstate)
+		__drm_atomic_helper_crtc_reset(crtc, &cstate->base);
+	else
+		__drm_atomic_helper_crtc_reset(crtc, NULL);
 }
 
 /**
@@ -898,6 +904,20 @@
 	u32 pipe_id;
 };
 
+static bool dpu_crtc_needs_dirtyfb(struct drm_crtc_state *cstate)
+{
+	struct drm_crtc *crtc = cstate->crtc;
+	struct drm_encoder *encoder;
+
+	drm_for_each_encoder_mask (encoder, crtc->dev, cstate->encoder_mask) {
+		if (dpu_encoder_get_intf_mode(encoder) == INTF_MODE_CMD) {
+			return true;
+		}
+	}
+
+	return false;
+}
+
 static int dpu_crtc_atomic_check(struct drm_crtc *crtc,
 		struct drm_atomic_state *state)
 {
@@ -918,8 +938,11 @@
 	const struct drm_plane_state *pipe_staged[SSPP_MAX];
 	int left_zpos_cnt = 0, right_zpos_cnt = 0;
 	struct drm_rect crtc_rect = { 0 };
+	bool needs_dirtyfb = dpu_crtc_needs_dirtyfb(crtc_state);
 
 	pstates = kzalloc(sizeof(*pstates) * DPU_STAGE_MAX * 4, GFP_KERNEL);
+	if (!pstates)
+		return -ENOMEM;
 
 	if (!crtc_state->enable || !crtc_state->active) {
 		DRM_DEBUG_ATOMIC("crtc%d -> enable %d, active %d, skip atomic_check\n",
@@ -949,6 +972,7 @@
 
 	 /* get plane state for all drm planes associated with crtc state */
 	drm_atomic_crtc_state_for_each_plane_state(plane, pstate, crtc_state) {
+		struct dpu_plane_state *dpu_pstate = to_dpu_plane_state(pstate);
 		struct drm_rect dst, clip = crtc_rect;
 
 		if (IS_ERR_OR_NULL(pstate)) {
@@ -960,11 +984,16 @@
 		if (cnt >= DPU_STAGE_MAX * 4)
 			continue;
 
-		pstates[cnt].dpu_pstate = to_dpu_plane_state(pstate);
+		if (!pstate->visible)
+			continue;
+
+		pstates[cnt].dpu_pstate = dpu_pstate;
 		pstates[cnt].drm_pstate = pstate;
 		pstates[cnt].stage = pstate->normalized_zpos;
 		pstates[cnt].pipe_id = dpu_plane_pipe(plane);
 
+		dpu_pstate->needs_dirtyfb = needs_dirtyfb;
+
 		if (pipe_staged[pstates[cnt].pipe_id]) {
 			multirect_plane[multirect_count].r0 =
 				pipe_staged[pstates[cnt].pipe_id];
@@ -1351,6 +1380,8 @@
 struct drm_crtc *dpu_crtc_init(struct drm_device *dev, struct drm_plane *plane,
 				struct drm_plane *cursor)
 {
+	struct msm_drm_private *priv = dev->dev_private;
+	struct dpu_kms *dpu_kms = to_dpu_kms(priv->kms);
 	struct drm_crtc *crtc = NULL;
 	struct dpu_crtc *dpu_crtc = NULL;
 	int i;
@@ -1382,7 +1413,8 @@
 
 	drm_crtc_helper_add(crtc, &dpu_crtc_helper_funcs);
 
-	drm_crtc_enable_color_mgmt(crtc, 0, true, 0);
+	if (dpu_kms->catalog->dspp_count)
+		drm_crtc_enable_color_mgmt(crtc, 0, true, 0);
 
 	/* save user friendly CRTC name for later */
 	snprintf(dpu_crtc->name, DPU_CRTC_NAME_SIZE, "crtc%u", crtc->base.id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
@@ -46,6 +46,9 @@
 		(p) ? ((p)->hw_pp ? (p)->hw_pp->idx - PINGPONG_0 : -1) : -1, \
 		##__VA_ARGS__)
 
+#define DPU_ERROR_ENC_RATELIMITED(e, fmt, ...) DPU_ERROR_RATELIMITED("enc%d " fmt,\
+		(e) ? (e)->base.base.id : -1, ##__VA_ARGS__)
+
 /*
  * Two to anticipate panels that can do cmd/vid dynamic switching
  * plan is to create all possible physical encoder types, and switch between
@@ -168,6 +171,7 @@
  * @vsync_event_work:		worker to handle vsync event for autorefresh
  * @topology:                   topology of the display
  * @idle_timeout:		idle timeout duration in milliseconds
+ * @dp:				msm_dp pointer, for DP encoders
  */
 struct dpu_encoder_virt {
 	struct drm_encoder base;
@@ -206,6 +210,8 @@
 	struct msm_display_topology topology;
 
 	u32 idle_timeout;
+
+	struct msm_dp *dp;
 };
 
 #define to_dpu_encoder_virt(x) container_of(x, struct dpu_encoder_virt, base)
@@ -634,7 +640,7 @@
 		if (drm_atomic_crtc_needs_modeset(crtc_state)) {
 			dpu_rm_release(global_state, drm_enc);
 
-			if (!crtc_state->active_changed || crtc_state->active)
+			if (!crtc_state->active_changed || crtc_state->enable)
 				ret = dpu_rm_reserve(&dpu_kms->rm, global_state,
 						drm_enc, crtc_state, topology);
 		}
@@ -1000,8 +1006,8 @@
 
 	trace_dpu_enc_mode_set(DRMID(drm_enc));
 
-	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS && priv->dp)
-		msm_dp_display_mode_set(priv->dp, drm_enc, mode, adj_mode);
+	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS)
+		msm_dp_display_mode_set(dpu_enc->dp, drm_enc, mode, adj_mode);
 
 	list_for_each_entry(conn_iter, connector_list, head)
 		if (conn_iter->encoder == drm_enc)
@@ -1107,7 +1113,7 @@
 	}
 
 
-	if (dpu_enc->disp_info.intf_type == DRM_MODE_CONNECTOR_DisplayPort &&
+	if (dpu_enc->disp_info.intf_type == DRM_MODE_ENCODER_TMDS &&
 		dpu_enc->cur_master->hw_mdptop &&
 		dpu_enc->cur_master->hw_mdptop->ops.intf_audio_select)
 		dpu_enc->cur_master->hw_mdptop->ops.intf_audio_select(
@@ -1182,9 +1188,8 @@
 
 	_dpu_encoder_virt_enable_helper(drm_enc);
 
-	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS && priv->dp) {
-		ret = msm_dp_display_enable(priv->dp,
-						drm_enc);
+	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS) {
+		ret = msm_dp_display_enable(dpu_enc->dp, drm_enc);
 		if (ret) {
 			DPU_ERROR_ENC(dpu_enc, "dp display enable failed: %d\n",
 				ret);
@@ -1224,8 +1229,8 @@
 	/* wait for idle */
 	dpu_encoder_wait_for_event(drm_enc, MSM_ENC_TX_COMPLETE);
 
-	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS && priv->dp) {
-		if (msm_dp_display_pre_disable(priv->dp, drm_enc))
+	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS) {
+		if (msm_dp_display_pre_disable(dpu_enc->dp, drm_enc))
 			DPU_ERROR_ENC(dpu_enc, "dp display push idle failed\n");
 	}
 
@@ -1253,8 +1258,8 @@
 
 	DPU_DEBUG_ENC(dpu_enc, "encoder disabled\n");
 
-	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS && priv->dp) {
-		if (msm_dp_display_disable(priv->dp, drm_enc))
+	if (drm_enc->encoder_type == DRM_MODE_ENCODER_TMDS) {
+		if (msm_dp_display_disable(dpu_enc->dp, drm_enc))
 			DPU_ERROR_ENC(dpu_enc, "dp display disable failed\n");
 	}
 
@@ -2124,7 +2129,7 @@
 		return;
 	}
 
-	DPU_ERROR_ENC(dpu_enc, "frame done timeout\n");
+	DPU_ERROR_ENC_RATELIMITED(dpu_enc, "frame done timeout\n");
 
 	event = DPU_ENCODER_FRAME_EVENT_ERROR;
 	trace_dpu_enc_frame_done_timeout(DRMID(drm_enc), event);
@@ -2170,7 +2175,8 @@
 		timer_setup(&dpu_enc->vsync_event_timer,
 				dpu_encoder_vsync_event_handler,
 				0);
-
+	else if (disp_info->intf_type == DRM_MODE_ENCODER_TMDS)
+		dpu_enc->dp = priv->dp;
 
 	INIT_DELAYED_WORK(&dpu_enc->delayed_off_work,
 			dpu_encoder_off_work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
@@ -441,9 +441,6 @@
 
 	_dpu_encoder_phys_cmd_pingpong_config(phys_enc);
 
-	if (!dpu_encoder_phys_cmd_is_master(phys_enc))
-		return;
-
 	ctl = phys_enc->hw_ctl;
 	ctl->ops.update_pending_flush_intf(ctl, phys_enc->intf_idx);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
@@ -267,12 +267,14 @@
 		mode.htotal >>= 1;
 		mode.hsync_start >>= 1;
 		mode.hsync_end >>= 1;
+		mode.hskew >>= 1;
 
 		DPU_DEBUG_VIDENC(phys_enc,
-			"split_role %d, halve horizontal %d %d %d %d\n",
+			"split_role %d, halve horizontal %d %d %d %d %d\n",
 			phys_enc->split_role,
 			mode.hdisplay, mode.htotal,
-			mode.hsync_start, mode.hsync_end);
+			mode.hsync_start, mode.hsync_end,
+			mode.hskew);
 	}
 
 	drm_mode_to_intf_timing_params(phys_enc, &mode, &timing_params);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
@@ -53,9 +53,13 @@
 
 #define INTF_SDM845_MASK (0)
 
-#define INTF_SC7180_MASK BIT(DPU_INTF_INPUT_CTRL) | BIT(DPU_INTF_TE)
+#define INTF_SC7180_MASK \
+	(BIT(DPU_INTF_INPUT_CTRL) | \
+	 BIT(DPU_INTF_TE) | \
+	 BIT(DPU_INTF_STATUS_SUPPORTED) | \
+	 BIT(DPU_DATA_HCTL_EN))
 
-#define INTF_SC7280_MASK INTF_SC7180_MASK | BIT(DPU_DATA_HCTL_EN)
+#define INTF_SC7280_MASK (INTF_SC7180_MASK)
 
 #define IRQ_SDM845_MASK (BIT(MDP_SSPP_TOP0_INTR) | \
 			 BIT(MDP_SSPP_TOP0_INTR2) | \
@@ -375,19 +379,19 @@
 static const struct dpu_ctl_cfg sc7180_ctl[] = {
 	{
 	.name = "ctl_0", .id = CTL_0,
-	.base = 0x1000, .len = 0xE4,
+	.base = 0x1000, .len = 0x1dc,
 	.features = BIT(DPU_CTL_ACTIVE_CFG),
 	.intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 9),
 	},
 	{
 	.name = "ctl_1", .id = CTL_1,
-	.base = 0x1200, .len = 0xE4,
+	.base = 0x1200, .len = 0x1dc,
 	.features = BIT(DPU_CTL_ACTIVE_CFG),
 	.intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 10),
 	},
 	{
 	.name = "ctl_2", .id = CTL_2,
-	.base = 0x1400, .len = 0xE4,
+	.base = 0x1400, .len = 0x1dc,
 	.features = BIT(DPU_CTL_ACTIVE_CFG),
 	.intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 11),
 	},
@@ -804,7 +808,7 @@
 #define MERGE_3D_BLK(_name, _id, _base) \
 	{\
 	.name = _name, .id = _id, \
-	.base = _base, .len = 0x100, \
+	.base = _base, .len = 0x8, \
 	.features = MERGE_3D_SM8150_MASK, \
 	.sblk = NULL \
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
@@ -191,17 +191,19 @@
 
 /**
  * INTF sub-blocks
- * @DPU_INTF_INPUT_CTRL         Supports the setting of pp block from which
- *                              pixel data arrives to this INTF
- * @DPU_INTF_TE                 INTF block has TE configuration support
- * @DPU_DATA_HCTL_EN            Allows data to be transferred at different rate
-                                than video timing
+ * @DPU_INTF_INPUT_CTRL             Supports the setting of pp block from which
+ *                                  pixel data arrives to this INTF
+ * @DPU_INTF_TE                     INTF block has TE configuration support
+ * @DPU_DATA_HCTL_EN                Allows data to be transferred at different rate
+ *                                  than video timing
+ * @DPU_INTF_STATUS_SUPPORTED       INTF block has INTF_STATUS register
  * @DPU_INTF_MAX
  */
 enum {
 	DPU_INTF_INPUT_CTRL = 0x1,
 	DPU_INTF_TE,
 	DPU_DATA_HCTL_EN,
+	DPU_INTF_STATUS_SUPPORTED,
 	DPU_INTF_MAX
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dspp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dspp.c
@@ -26,9 +26,16 @@
 		struct dpu_hw_pcc_cfg *cfg)
 {
 
-	u32 base = ctx->cap->sblk->pcc.base;
+	u32 base;
 
-	if (!ctx || !base) {
+	if (!ctx) {
+		DRM_ERROR("invalid ctx %pK\n", ctx);
+		return;
+	}
+
+	base = ctx->cap->sblk->pcc.base;
+
+	if (!base) {
 		DRM_ERROR("invalid ctx %pK pcc base 0x%x\n", ctx, base);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.c
@@ -12,7 +12,7 @@
 
 /**
  * Register offsets in MDSS register file for the interrupt registers
- * w.r.t. to the MDP base
+ * w.r.t. the MDP base
  */
 #define MDP_SSPP_TOP0_OFF		0x0
 #define MDP_INTF_0_OFF			0x6A000
@@ -20,6 +20,10 @@
 #define MDP_INTF_2_OFF			0x6B000
 #define MDP_INTF_3_OFF			0x6B800
 #define MDP_INTF_4_OFF			0x6C000
+#define MDP_INTF_5_OFF			0x6C800
+#define INTF_INTR_EN			0x1c0
+#define INTF_INTR_STATUS		0x1c4
+#define INTF_INTR_CLEAR			0x1c8
 #define MDP_AD4_0_OFF			0x7C000
 #define MDP_AD4_1_OFF			0x7D000
 #define MDP_AD4_INTR_EN_OFF		0x41c
@@ -88,6 +92,11 @@
 		MDP_INTF_4_OFF+INTF_INTR_STATUS
 	},
 	{
+		MDP_INTF_5_OFF+INTF_INTR_CLEAR,
+		MDP_INTF_5_OFF+INTF_INTR_EN,
+		MDP_INTF_5_OFF+INTF_INTR_STATUS
+	},
+	{
 		MDP_AD4_0_OFF + MDP_AD4_INTR_CLEAR_OFF,
 		MDP_AD4_0_OFF + MDP_AD4_INTR_EN_OFF,
 		MDP_AD4_0_OFF + MDP_AD4_INTR_STATUS_OFF,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.h
@@ -22,6 +22,7 @@
 	MDP_INTF2_INTR,
 	MDP_INTF3_INTR,
 	MDP_INTF4_INTR,
+	MDP_INTF5_INTR,
 	MDP_AD4_0_INTR,
 	MDP_AD4_1_INTR,
 	MDP_INTF0_7xxx_INTR,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
@@ -53,12 +53,8 @@
 #define   INTF_TPG_RGB_MAPPING          0x11C
 #define   INTF_PROG_FETCH_START         0x170
 #define   INTF_PROG_ROT_START           0x174
-
-#define   INTF_FRAME_LINE_COUNT_EN      0x0A8
-#define   INTF_FRAME_COUNT              0x0AC
-#define   INTF_LINE_COUNT               0x0B0
-
 #define   INTF_MUX                      0x25C
+#define   INTF_STATUS                   0x26C
 
 static const struct dpu_intf_cfg *_intf_offset(enum dpu_intf intf,
 		const struct dpu_mdss_cfg *m,
@@ -148,6 +144,7 @@
 		active_v_end = active_v_start + (p->yres * hsync_period) - 1;
 
 		display_v_start += p->hsync_pulse_width + p->h_back_porch;
+		display_v_end   -= p->h_front_porch; 
 
 		active_hctl = (active_h_end << 16) | active_h_start;
 		display_hctl = active_hctl;
@@ -263,8 +260,13 @@
 		struct intf_status *s)
 {
 	struct dpu_hw_blk_reg_map *c = &intf->hw;
+	unsigned long cap = intf->cap->features;
+
+	if (cap & BIT(DPU_INTF_STATUS_SUPPORTED))
+		s->is_en = DPU_REG_READ(c, INTF_STATUS) & BIT(0);
+	else
+		s->is_en = DPU_REG_READ(c, INTF_TIMING_ENGINE_EN);
 
-	s->is_en = DPU_REG_READ(c, INTF_TIMING_ENGINE_EN);
 	s->is_prog_fetch_en = !!(DPU_REG_READ(c, INTF_CONFIG) & BIT(31));
 	if (s->is_en) {
 		s->frame_count = DPU_REG_READ(c, INTF_FRAME_COUNT);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c
@@ -138,11 +138,13 @@
 		u32 *idx)
 {
 	int rc = 0;
-	const struct dpu_sspp_sub_blks *sblk = ctx->cap->sblk;
+	const struct dpu_sspp_sub_blks *sblk;
 
-	if (!ctx)
+	if (!ctx || !ctx->cap || !ctx->cap->sblk)
 		return -EINVAL;
 
+	sblk = ctx->cap->sblk;
+
 	switch (s_id) {
 	case DPU_SSPP_SRC:
 		*idx = sblk->src_blk.base;
@@ -419,7 +421,7 @@
 
 	(void)pe;
 	if (_sspp_subblk_offset(ctx, DPU_SSPP_SCALER_QSEED3, &idx) || !sspp
-		|| !scaler3_cfg || !ctx || !ctx->cap || !ctx->cap->sblk)
+		|| !scaler3_cfg)
 		return;
 
 	dpu_hw_setup_scaler3(&ctx->hw, scaler3_cfg, idx,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_hwio.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_hwio.h
@@ -20,9 +20,6 @@
 #define HIST_INTR_EN                    0x01c
 #define HIST_INTR_STATUS                0x020
 #define HIST_INTR_CLEAR                 0x024
-#define INTF_INTR_EN                    0x1C0
-#define INTF_INTR_STATUS                0x1C4
-#define INTF_INTR_CLEAR                 0x1C8
 #define SPLIT_DISPLAY_EN                0x2F4
 #define SPLIT_DISPLAY_UPPER_PIPE_CTRL   0x2F8
 #define DSPP_IGC_COLOR0_RAM_LUTN        0x300
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c
@@ -73,8 +73,8 @@
 					&status);
 	} else {
 		seq_puts(s, "\nSafe signal status:\n");
-		if (kms->hw_mdp->ops.get_danger_status)
-			kms->hw_mdp->ops.get_danger_status(kms->hw_mdp,
+		if (kms->hw_mdp->ops.get_safe_status)
+			kms->hw_mdp->ops.get_safe_status(kms->hw_mdp,
 					&status);
 	}
 	pm_runtime_put_sync(&kms->pdev->dev);
@@ -725,11 +725,11 @@
 	_dpu_kms_mmu_destroy(dpu_kms);
 
 	if (dpu_kms->catalog) {
-		for (i = 0; i < dpu_kms->catalog->vbif_count; i++) {
-			u32 vbif_idx = dpu_kms->catalog->vbif[i].id;
-
-			if ((vbif_idx < VBIF_MAX) && dpu_kms->hw_vbif[vbif_idx])
-				dpu_hw_vbif_destroy(dpu_kms->hw_vbif[vbif_idx]);
+		for (i = 0; i < ARRAY_SIZE(dpu_kms->hw_vbif); i++) {
+			if (dpu_kms->hw_vbif[i]) {
+				dpu_hw_vbif_destroy(dpu_kms->hw_vbif[i]);
+				dpu_kms->hw_vbif[i] = NULL;
+			}
 		}
 	}
 
@@ -908,6 +908,10 @@
 		return 0;
 
 	mmu = msm_iommu_new(dpu_kms->dev->dev, domain);
+	if (IS_ERR(mmu)) {
+		iommu_domain_free(domain);
+		return PTR_ERR(mmu);
+	}
 	aspace = msm_gem_address_space_create(mmu, "dpu1",
 		0x1000, 0x100000000 - 0x1000);
 
@@ -995,7 +999,9 @@
 
 	dpu_kms_parse_data_bus_icc_path(dpu_kms);
 
-	pm_runtime_get_sync(&dpu_kms->pdev->dev);
+	rc = pm_runtime_resume_and_get(&dpu_kms->pdev->dev);
+	if (rc < 0)
+		goto error;
 
 	dpu_kms->core_rev = readl_relaxed(dpu_kms->mmio + 0x0);
 
@@ -1041,7 +1047,7 @@
 	for (i = 0; i < dpu_kms->catalog->vbif_count; i++) {
 		u32 vbif_idx = dpu_kms->catalog->vbif[i].id;
 
-		dpu_kms->hw_vbif[i] = dpu_hw_vbif_init(vbif_idx,
+		dpu_kms->hw_vbif[vbif_idx] = dpu_hw_vbif_init(vbif_idx,
 				dpu_kms->vbif[vbif_idx], dpu_kms->catalog);
 		if (IS_ERR_OR_NULL(dpu_kms->hw_vbif[vbif_idx])) {
 			rc = PTR_ERR(dpu_kms->hw_vbif[vbif_idx]);
@@ -1180,7 +1186,7 @@
 
 	priv->kms = &dpu_kms->base;
 
-	return ret;
+	return 0;
 }
 
 static void dpu_unbind(struct device *dev, struct device *master, void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.h
@@ -32,26 +32,17 @@
  * @fmt: Pointer to format string
  */
 #define DPU_DEBUG(fmt, ...)                                                \
-	do {                                                               \
-		if (drm_debug_enabled(DRM_UT_KMS))                         \
-			DRM_DEBUG(fmt, ##__VA_ARGS__); \
-		else                                                       \
-			pr_debug(fmt, ##__VA_ARGS__);                      \
-	} while (0)
+	DRM_DEBUG_DRIVER(fmt, ##__VA_ARGS__)
 
 /**
  * DPU_DEBUG_DRIVER - macro for hardware driver logging
  * @fmt: Pointer to format string
  */
 #define DPU_DEBUG_DRIVER(fmt, ...)                                         \
-	do {                                                               \
-		if (drm_debug_enabled(DRM_UT_DRIVER))                      \
-			DRM_ERROR(fmt, ##__VA_ARGS__); \
-		else                                                       \
-			pr_debug(fmt, ##__VA_ARGS__);                      \
-	} while (0)
+	DRM_DEBUG_DRIVER(fmt, ##__VA_ARGS__)
 
 #define DPU_ERROR(fmt, ...) pr_err("[dpu error]" fmt, ##__VA_ARGS__)
+#define DPU_ERROR_RATELIMITED(fmt, ...) pr_err_ratelimited("[dpu error]" fmt, ##__VA_ARGS__)
 
 /**
  * ktime_compare_safe - compare two ktime structures
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
@@ -158,6 +158,7 @@
 	const struct dpu_format *fmt = NULL;
 	struct dpu_kms *dpu_kms = _dpu_plane_get_kms(plane);
 	int src_width, src_height, dst_height, fps;
+	u64 plane_pixel_rate, plane_bit_rate;
 	u64 plane_prefill_bw;
 	u64 plane_bw;
 	u32 hw_latency_lines;
@@ -180,13 +181,12 @@
 	scale_factor = src_height > dst_height ?
 		mult_frac(src_height, 1, dst_height) : 1;
 
-	plane_bw =
-		src_width * mode->vtotal * fps * fmt->bpp *
-		scale_factor;
-
-	plane_prefill_bw =
-		src_width * hw_latency_lines * fps * fmt->bpp *
-		scale_factor * mode->vtotal;
+	plane_pixel_rate = src_width * mode->vtotal * fps;
+	plane_bit_rate = plane_pixel_rate * fmt->bpp;
+
+	plane_bw = plane_bit_rate * scale_factor;
+
+	plane_prefill_bw = plane_bw * hw_latency_lines;
 
 	if ((vbp+vpw) > hw_latency_lines)
 		do_div(plane_prefill_bw, (vbp+vpw));
@@ -894,7 +894,7 @@
 
 	if (pstate->aspace) {
 		ret = msm_framebuffer_prepare(new_state->fb,
-				pstate->aspace);
+				pstate->aspace, pstate->needs_dirtyfb);
 		if (ret) {
 			DPU_ERROR("failed to prepare framebuffer\n");
 			return ret;
@@ -906,6 +906,9 @@
 			new_state->fb, &layout);
 	if (ret) {
 		DPU_ERROR_PLANE(pdpu, "failed to get format layout, %d\n", ret);
+		if (pstate->aspace)
+			msm_framebuffer_cleanup(new_state->fb, pstate->aspace,
+						pstate->needs_dirtyfb);
 		return ret;
 	}
 
@@ -925,7 +928,8 @@
 
 	DPU_DEBUG_PLANE(pdpu, "FB[%u]\n", old_state->fb->base.id);
 
-	msm_framebuffer_cleanup(old_state->fb, old_pstate->aspace);
+	msm_framebuffer_cleanup(old_state->fb, old_pstate->aspace,
+				old_pstate->needs_dirtyfb);
 }
 
 static bool dpu_plane_validate_src(struct drm_rect *src,
@@ -1088,7 +1092,7 @@
 	struct dpu_plane_state *pstate = to_dpu_plane_state(state);
 	struct drm_crtc *crtc = state->crtc;
 	struct drm_framebuffer *fb = state->fb;
-	bool is_rt_pipe, update_qos_remap;
+	bool is_rt_pipe;
 	const struct dpu_format *fmt =
 		to_dpu_format(msm_framebuffer_format(fb));
 
@@ -1099,6 +1103,9 @@
 	pstate->pending = true;
 
 	is_rt_pipe = (dpu_crtc_get_client_type(crtc) != NRT_CLIENT);
+	pstate->needs_qos_remap |= (is_rt_pipe != pdpu->is_rt_pipe);
+	pdpu->is_rt_pipe = is_rt_pipe;
+
 	_dpu_plane_set_qos_ctrl(plane, false, DPU_PLANE_QOS_PANIC_CTRL);
 
 	DPU_DEBUG_PLANE(pdpu, "FB[%u] " DRM_RECT_FP_FMT "->crtc%u " DRM_RECT_FMT
@@ -1204,14 +1211,8 @@
 		_dpu_plane_set_ot_limit(plane, crtc);
 	}
 
-	update_qos_remap = (is_rt_pipe != pdpu->is_rt_pipe) ||
-			pstate->needs_qos_remap;
-
-	if (update_qos_remap) {
-		if (is_rt_pipe != pdpu->is_rt_pipe)
-			pdpu->is_rt_pipe = is_rt_pipe;
-		else if (pstate->needs_qos_remap)
-			pstate->needs_qos_remap = false;
+	if (pstate->needs_qos_remap) {
+		pstate->needs_qos_remap = false;
 		_dpu_plane_set_qos_remap(plane);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
@@ -28,6 +28,7 @@
  * @cdp_cfg:	CDP configuration
  * @plane_fetch_bw: calculated BW per plane
  * @plane_clk: calculated clk per plane
+ * @needs_dirtyfb: whether attached CRTC needs pixel data explicitly flushed
  */
 struct dpu_plane_state {
 	struct drm_plane_state base;
@@ -45,6 +46,8 @@
 	struct dpu_hw_pipe_cdp_cfg cdp_cfg;
 	u64 plane_fetch_bw;
 	u64 plane_clk;
+
+	bool needs_dirtyfb;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c
@@ -35,6 +35,14 @@
 {
 	int i;
 
+	for (i = 0; i < ARRAY_SIZE(rm->dspp_blks); i++) {
+		struct dpu_hw_dspp *hw;
+
+		if (rm->dspp_blks[i]) {
+			hw = to_dpu_hw_dspp(rm->dspp_blks[i]);
+			dpu_hw_dspp_destroy(hw);
+		}
+	}
 	for (i = 0; i < ARRAY_SIZE(rm->pingpong_blks); i++) {
 		struct dpu_hw_pingpong *hw;
 
@@ -655,6 +663,11 @@
 				  blks_size, enc_id);
 			break;
 		}
+		if (!hw_blks[i]) {
+			DPU_ERROR("Allocated resource %d unavailable to assign to enc %d\n",
+				  type, enc_id);
+			break;
+		}
 		blks[num_blks++] = hw_blks[i];
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c
@@ -11,6 +11,14 @@
 #include "dpu_hw_vbif.h"
 #include "dpu_trace.h"
 
+static struct dpu_hw_vbif *dpu_get_vbif(struct dpu_kms *dpu_kms, enum dpu_vbif vbif_idx)
+{
+	if (vbif_idx < ARRAY_SIZE(dpu_kms->hw_vbif))
+		return dpu_kms->hw_vbif[vbif_idx];
+
+	return NULL;
+}
+
 /**
  * _dpu_vbif_wait_for_xin_halt - wait for the xin to halt
  * @vbif:	Pointer to hardware vbif driver
@@ -148,20 +156,15 @@
 void dpu_vbif_set_ot_limit(struct dpu_kms *dpu_kms,
 		struct dpu_vbif_set_ot_params *params)
 {
-	struct dpu_hw_vbif *vbif = NULL;
+	struct dpu_hw_vbif *vbif;
 	struct dpu_hw_mdp *mdp;
 	bool forced_on = false;
 	u32 ot_lim;
-	int ret, i;
+	int ret;
 
 	mdp = dpu_kms->hw_mdp;
 
-	for (i = 0; i < ARRAY_SIZE(dpu_kms->hw_vbif); i++) {
-		if (dpu_kms->hw_vbif[i] &&
-				dpu_kms->hw_vbif[i]->idx == params->vbif_idx)
-			vbif = dpu_kms->hw_vbif[i];
-	}
-
+	vbif = dpu_get_vbif(dpu_kms, params->vbif_idx);
 	if (!vbif || !mdp) {
 		DRM_DEBUG_ATOMIC("invalid arguments vbif %d mdp %d\n",
 				vbif != NULL, mdp != NULL);
@@ -204,7 +207,7 @@
 void dpu_vbif_set_qos_remap(struct dpu_kms *dpu_kms,
 		struct dpu_vbif_set_qos_params *params)
 {
-	struct dpu_hw_vbif *vbif = NULL;
+	struct dpu_hw_vbif *vbif;
 	struct dpu_hw_mdp *mdp;
 	bool forced_on = false;
 	const struct dpu_vbif_qos_tbl *qos_tbl;
@@ -216,13 +219,7 @@
 	}
 	mdp = dpu_kms->hw_mdp;
 
-	for (i = 0; i < ARRAY_SIZE(dpu_kms->hw_vbif); i++) {
-		if (dpu_kms->hw_vbif[i] &&
-				dpu_kms->hw_vbif[i]->idx == params->vbif_idx) {
-			vbif = dpu_kms->hw_vbif[i];
-			break;
-		}
-	}
+	vbif = dpu_get_vbif(dpu_kms, params->vbif_idx);
 
 	if (!vbif || !vbif->cap) {
 		DPU_ERROR("invalid vbif %d\n", params->vbif_idx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp4/mdp4_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp4/mdp4_crtc.c
@@ -269,6 +269,7 @@
 {
 	struct mdp4_crtc *mdp4_crtc = to_mdp4_crtc(crtc);
 	struct mdp4_kms *mdp4_kms = get_kms(crtc);
+	unsigned long flags;
 
 	DBG("%s", mdp4_crtc->name);
 
@@ -281,6 +282,14 @@
 	mdp_irq_unregister(&mdp4_kms->base, &mdp4_crtc->err);
 	mdp4_disable(mdp4_kms);
 
+	if (crtc->state->event && !crtc->state->active) {
+		WARN_ON(mdp4_crtc->event);
+		spin_lock_irqsave(&mdp4_kms->dev->event_lock, flags);
+		drm_crtc_send_vblank_event(crtc, crtc->state->event);
+		crtc->state->event = NULL;
+		spin_unlock_irqrestore(&mdp4_kms->dev->event_lock, flags);
+	}
+
 	mdp4_crtc->enabled = false;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp4/mdp4_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp4/mdp4_kms.c
@@ -223,6 +223,7 @@
 		encoder = mdp4_lcdc_encoder_init(dev, panel_node);
 		if (IS_ERR(encoder)) {
 			DRM_DEV_ERROR(dev->dev, "failed to construct LCDC encoder\n");
+			of_node_put(panel_node);
 			return PTR_ERR(encoder);
 		}
 
@@ -232,6 +233,7 @@
 		connector = mdp4_lvds_connector_init(dev, panel_node, encoder);
 		if (IS_ERR(connector)) {
 			DRM_DEV_ERROR(dev->dev, "failed to initialize LVDS connector\n");
+			of_node_put(panel_node);
 			return PTR_ERR(connector);
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp4/mdp4_lvds_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp4/mdp4_lvds_connector.c
@@ -56,8 +56,9 @@
 	return ret;
 }
 
-static int mdp4_lvds_connector_mode_valid(struct drm_connector *connector,
-				 struct drm_display_mode *mode)
+static enum drm_mode_status
+mdp4_lvds_connector_mode_valid(struct drm_connector *connector,
+			       struct drm_display_mode *mode)
 {
 	struct mdp4_lvds_connector *mdp4_lvds_connector =
 			to_mdp4_lvds_connector(connector);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c
@@ -7,6 +7,7 @@
 #include <drm/drm_atomic.h>
 #include <drm/drm_damage_helper.h>
 #include <drm/drm_fourcc.h>
+#include <drm/drm_gem_atomic_helper.h>
 
 #include "mdp4_kms.h"
 
@@ -90,6 +91,20 @@
 		.atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
 };
 
+static int mdp4_plane_prepare_fb(struct drm_plane *plane,
+				 struct drm_plane_state *new_state)
+{
+	struct msm_drm_private *priv = plane->dev->dev_private;
+	struct msm_kms *kms = priv->kms;
+
+	if (!new_state->fb)
+		return 0;
+
+	drm_gem_plane_helper_prepare_fb(plane, new_state);
+
+	return msm_framebuffer_prepare(new_state->fb, kms->aspace, false);
+}
+
 static void mdp4_plane_cleanup_fb(struct drm_plane *plane,
 				  struct drm_plane_state *old_state)
 {
@@ -102,7 +117,7 @@
 		return;
 
 	DBG("%s: cleanup: FB[%u]", mdp4_plane->name, fb->base.id);
-	msm_framebuffer_cleanup(fb, kms->aspace);
+	msm_framebuffer_cleanup(fb, kms->aspace, false);
 }
 
 
@@ -130,7 +145,7 @@
 }
 
 static const struct drm_plane_helper_funcs mdp4_plane_helper_funcs = {
-		.prepare_fb = msm_atomic_prepare_fb,
+		.prepare_fb = mdp4_plane_prepare_fb,
 		.cleanup_fb = mdp4_plane_cleanup_fb,
 		.atomic_check = mdp4_plane_atomic_check,
 		.atomic_update = mdp4_plane_atomic_update,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
@@ -612,9 +612,15 @@
 		if (ret)
 			return ret;
 
-		mdp5_mixer_release(new_crtc_state->state, old_mixer);
+		ret = mdp5_mixer_release(new_crtc_state->state, old_mixer);
+		if (ret)
+			return ret;
+
 		if (old_r_mixer) {
-			mdp5_mixer_release(new_crtc_state->state, old_r_mixer);
+			ret = mdp5_mixer_release(new_crtc_state->state, old_r_mixer);
+			if (ret)
+				return ret;
+
 			if (!need_right_mixer)
 				pipeline->r_mixer = NULL;
 		}
@@ -690,6 +696,8 @@
 {
 	struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state,
 									  crtc);
+	struct mdp5_crtc_state *mdp5_cstate = to_mdp5_crtc_state(crtc_state);
+	struct mdp5_interface *intf = mdp5_cstate->pipeline.intf;
 	struct mdp5_kms *mdp5_kms = get_kms(crtc);
 	struct drm_plane *plane;
 	struct drm_device *dev = crtc->dev;
@@ -706,12 +714,18 @@
 	DBG("%s: check", crtc->name);
 
 	drm_atomic_crtc_state_for_each_plane_state(plane, pstate, crtc_state) {
+		struct mdp5_plane_state *mdp5_pstate =
+				to_mdp5_plane_state(pstate);
+
 		if (!pstate->visible)
 			continue;
 
 		pstates[cnt].plane = plane;
 		pstates[cnt].state = to_mdp5_plane_state(pstate);
 
+		mdp5_pstate->needs_dirtyfb =
+			intf->mode == MDP5_INTF_DSI_MODE_COMMAND;
+
 		/*
 		 * if any plane on this crtc uses 2 hwpipes, then we need
 		 * the crtc to have a right hwmixer.
@@ -983,8 +997,10 @@
 
 	ret = msm_gem_get_and_pin_iova(cursor_bo, kms->aspace,
 			&mdp5_crtc->cursor.iova);
-	if (ret)
+	if (ret) {
+		drm_gem_object_put(cursor_bo);
 		return -EINVAL;
+	}
 
 	pm_runtime_get_sync(&pdev->dev);
 
@@ -1122,7 +1138,10 @@
 	if (crtc->state)
 		mdp5_crtc_destroy_state(crtc, crtc->state);
 
-	__drm_atomic_helper_crtc_reset(crtc, &mdp5_cstate->base);
+	if (mdp5_cstate)
+		__drm_atomic_helper_crtc_reset(crtc, &mdp5_cstate->base);
+	else
+		__drm_atomic_helper_crtc_reset(crtc, NULL);
 }
 
 static const struct drm_crtc_funcs mdp5_crtc_no_lm_cursor_funcs = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c
@@ -598,9 +598,9 @@
 	}
 
 	irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
-	if (irq < 0) {
-		ret = irq;
-		DRM_DEV_ERROR(&pdev->dev, "failed to get irq: %d\n", ret);
+	if (!irq) {
+		ret = -EINVAL;
+		DRM_DEV_ERROR(&pdev->dev, "failed to get irq\n");
 		goto fail;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.h
@@ -100,6 +100,11 @@
 
 	/* assigned by crtc blender */
 	enum mdp_mixer_stage_id stage;
+
+	/* whether attached CRTC needs pixel data explicitly flushed to
+	 * display (ex. DSI command mode display)
+	 */
+	bool needs_dirtyfb;
 };
 #define to_mdp5_plane_state(x) \
 		container_of(x, struct mdp5_plane_state, base)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_mixer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_mixer.c
@@ -116,21 +116,28 @@
 	return 0;
 }
 
-void mdp5_mixer_release(struct drm_atomic_state *s, struct mdp5_hw_mixer *mixer)
+int mdp5_mixer_release(struct drm_atomic_state *s, struct mdp5_hw_mixer *mixer)
 {
 	struct mdp5_global_state *global_state = mdp5_get_global_state(s);
-	struct mdp5_hw_mixer_state *new_state = &global_state->hwmixer;
+	struct mdp5_hw_mixer_state *new_state;
 
 	if (!mixer)
-		return;
+		return 0;
+
+	if (IS_ERR(global_state))
+		return PTR_ERR(global_state);
+
+	new_state = &global_state->hwmixer;
 
 	if (WARN_ON(!new_state->hwmixer_to_crtc[mixer->idx]))
-		return;
+		return -EINVAL;
 
 	DBG("%s: release from crtc %s", mixer->name,
 	    new_state->hwmixer_to_crtc[mixer->idx]->name);
 
 	new_state->hwmixer_to_crtc[mixer->idx] = NULL;
+
+	return 0;
 }
 
 void mdp5_mixer_destroy(struct mdp5_hw_mixer *mixer)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_mixer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_mixer.h
@@ -30,7 +30,7 @@
 int mdp5_mixer_assign(struct drm_atomic_state *s, struct drm_crtc *crtc,
 		      uint32_t caps, struct mdp5_hw_mixer **mixer,
 		      struct mdp5_hw_mixer **r_mixer);
-void mdp5_mixer_release(struct drm_atomic_state *s,
-			struct mdp5_hw_mixer *mixer);
+int mdp5_mixer_release(struct drm_atomic_state *s,
+		       struct mdp5_hw_mixer *mixer);
 
 #endif /* __MDP5_LM_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_pipe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_pipe.c
@@ -119,18 +119,24 @@
 	return 0;
 }
 
-void mdp5_pipe_release(struct drm_atomic_state *s, struct mdp5_hw_pipe *hwpipe)
+int mdp5_pipe_release(struct drm_atomic_state *s, struct mdp5_hw_pipe *hwpipe)
 {
 	struct msm_drm_private *priv = s->dev->dev_private;
 	struct mdp5_kms *mdp5_kms = to_mdp5_kms(to_mdp_kms(priv->kms));
-	struct mdp5_global_state *state = mdp5_get_global_state(s);
-	struct mdp5_hw_pipe_state *new_state = &state->hwpipe;
+	struct mdp5_global_state *state;
+	struct mdp5_hw_pipe_state *new_state;
 
 	if (!hwpipe)
-		return;
+		return 0;
+
+	state = mdp5_get_global_state(s);
+	if (IS_ERR(state))
+		return PTR_ERR(state);
+
+	new_state = &state->hwpipe;
 
 	if (WARN_ON(!new_state->hwpipe_to_plane[hwpipe->idx]))
-		return;
+		return -EINVAL;
 
 	DBG("%s: release from plane %s", hwpipe->name,
 		new_state->hwpipe_to_plane[hwpipe->idx]->name);
@@ -141,6 +147,8 @@
 	}
 
 	new_state->hwpipe_to_plane[hwpipe->idx] = NULL;
+
+	return 0;
 }
 
 void mdp5_pipe_destroy(struct mdp5_hw_pipe *hwpipe)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_pipe.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_pipe.h
@@ -37,7 +37,7 @@
 		     uint32_t caps, uint32_t blkcfg,
 		     struct mdp5_hw_pipe **hwpipe,
 		     struct mdp5_hw_pipe **r_hwpipe);
-void mdp5_pipe_release(struct drm_atomic_state *s, struct mdp5_hw_pipe *hwpipe);
+int mdp5_pipe_release(struct drm_atomic_state *s, struct mdp5_hw_pipe *hwpipe);
 
 struct mdp5_hw_pipe *mdp5_pipe_init(enum mdp5_pipe pipe,
 		uint32_t reg_offset, uint32_t caps);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c
@@ -8,6 +8,7 @@
 #include <drm/drm_atomic.h>
 #include <drm/drm_damage_helper.h>
 #include <drm/drm_fourcc.h>
+#include <drm/drm_gem_atomic_helper.h>
 #include <drm/drm_print.h>
 
 #include "mdp5_kms.h"
@@ -90,7 +91,10 @@
 		__drm_atomic_helper_plane_destroy_state(plane->state);
 
 	kfree(to_mdp5_plane_state(plane->state));
+	plane->state = NULL;
 	mdp5_state = kzalloc(sizeof(*mdp5_state), GFP_KERNEL);
+	if (!mdp5_state)
+		return;
 
 	if (plane->type == DRM_PLANE_TYPE_PRIMARY)
 		mdp5_state->base.zpos = STAGE_BASE;
@@ -124,8 +128,7 @@
 {
 	struct mdp5_plane_state *pstate = to_mdp5_plane_state(state);
 
-	if (state->fb)
-		drm_framebuffer_put(state->fb);
+	__drm_atomic_helper_plane_destroy_state(state);
 
 	kfree(pstate);
 }
@@ -140,18 +143,34 @@
 		.atomic_print_state = mdp5_plane_atomic_print_state,
 };
 
+static int mdp5_plane_prepare_fb(struct drm_plane *plane,
+				 struct drm_plane_state *new_state)
+{
+	struct msm_drm_private *priv = plane->dev->dev_private;
+	struct msm_kms *kms = priv->kms;
+	bool needs_dirtyfb = to_mdp5_plane_state(new_state)->needs_dirtyfb;
+
+	if (!new_state->fb)
+		return 0;
+
+	drm_gem_plane_helper_prepare_fb(plane, new_state);
+
+	return msm_framebuffer_prepare(new_state->fb, kms->aspace, needs_dirtyfb);
+}
+
 static void mdp5_plane_cleanup_fb(struct drm_plane *plane,
 				  struct drm_plane_state *old_state)
 {
 	struct mdp5_kms *mdp5_kms = get_kms(plane);
 	struct msm_kms *kms = &mdp5_kms->base.base;
 	struct drm_framebuffer *fb = old_state->fb;
+	bool needed_dirtyfb = to_mdp5_plane_state(old_state)->needs_dirtyfb;
 
 	if (!fb)
 		return;
 
 	DBG("%s: cleanup: FB[%u]", plane->name, fb->base.id);
-	msm_framebuffer_cleanup(fb, kms->aspace);
+	msm_framebuffer_cleanup(fb, kms->aspace, needed_dirtyfb);
 }
 
 static int mdp5_plane_atomic_check_with_state(struct drm_crtc_state *crtc_state,
@@ -294,12 +313,24 @@
 				mdp5_state->r_hwpipe = NULL;
 
 
-			mdp5_pipe_release(state->state, old_hwpipe);
-			mdp5_pipe_release(state->state, old_right_hwpipe);
+			ret = mdp5_pipe_release(state->state, old_hwpipe);
+			if (ret)
+				return ret;
+
+			ret = mdp5_pipe_release(state->state, old_right_hwpipe);
+			if (ret)
+				return ret;
+
 		}
 	} else {
-		mdp5_pipe_release(state->state, mdp5_state->hwpipe);
-		mdp5_pipe_release(state->state, mdp5_state->r_hwpipe);
+		ret = mdp5_pipe_release(state->state, mdp5_state->hwpipe);
+		if (ret)
+			return ret;
+
+		ret = mdp5_pipe_release(state->state, mdp5_state->r_hwpipe);
+		if (ret)
+			return ret;
+
 		mdp5_state->hwpipe = mdp5_state->r_hwpipe = NULL;
 	}
 
@@ -437,7 +468,7 @@
 }
 
 static const struct drm_plane_helper_funcs mdp5_plane_helper_funcs = {
-		.prepare_fb = msm_atomic_prepare_fb,
+		.prepare_fb = mdp5_plane_prepare_fb,
 		.cleanup_fb = mdp5_plane_cleanup_fb,
 		.atomic_check = mdp5_plane_atomic_check,
 		.atomic_update = mdp5_plane_atomic_update,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/mdp5/mdp5_smp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/mdp5/mdp5_smp.c
@@ -356,7 +356,7 @@
 
 			drm_printf(p, "%s:%d\t%d\t%s\n",
 				pipe2name(pipe), j, inuse,
-				plane ? plane->name : NULL);
+				plane ? plane->name : "(null)");
 
 			total += inuse;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/disp/msm_disp_snapshot_util.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/disp/msm_disp_snapshot_util.c
@@ -24,7 +24,7 @@
 	end_addr = base_addr + aligned_len;
 
 	if (!(*reg))
-		*reg = kzalloc(len_padded, GFP_KERNEL);
+		*reg = kvzalloc(len_padded, GFP_KERNEL);
 
 	if (*reg)
 		dump_addr = *reg;
@@ -46,20 +46,21 @@
 	}
 }
 
-static void msm_disp_state_print_regs(u32 **reg, u32 len, void __iomem *base_addr,
-		struct drm_printer *p)
+static void msm_disp_state_print_regs(const u32 *dump_addr, u32 len,
+		void __iomem *base_addr, struct drm_printer *p)
 {
 	int i;
-	u32 *dump_addr = NULL;
 	void __iomem *addr;
 	u32 num_rows;
 
+	if (!dump_addr) {
+		drm_printf(p, "Registers not stored\n");
+		return;
+	}
+
 	addr = base_addr;
 	num_rows = len / REG_DUMP_ALIGN;
 
-	if (*reg)
-		dump_addr = *reg;
-
 	for (i = 0; i < num_rows; i++) {
 		drm_printf(p, "0x%lx : %08x %08x %08x %08x\n",
 				(unsigned long)(addr - base_addr),
@@ -86,7 +87,7 @@
 
 	list_for_each_entry_safe(block, tmp, &state->blocks, node) {
 		drm_printf(p, "====================%s================\n", block->name);
-		msm_disp_state_print_regs(&block->state, block->size, block->base_addr, p);
+		msm_disp_state_print_regs(block->state, block->size, block->base_addr, p);
 	}
 
 	drm_printf(p, "===================dpu drm state================\n");
@@ -154,7 +155,7 @@
 
 	list_for_each_entry_safe(block, tmp, &disp_state->blocks, node) {
 		list_del(&block->node);
-		kfree(block->state);
+		kvfree(block->state);
 		kfree(block);
 	}
 
@@ -169,6 +170,8 @@
 	va_list va;
 
 	new_blk = kzalloc(sizeof(struct msm_disp_state_block), GFP_KERNEL);
+	if (!new_blk)
+		return;
 
 	va_start(va, fmt);
 
@@ -183,5 +186,5 @@
 	new_blk->base_addr = base_addr;
 
 	msm_disp_state_dump_regs(&new_blk->state, new_blk->size, base_addr);
-	list_add(&new_blk->node, &disp_state->blocks);
+	list_add_tail(&new_blk->node, &disp_state->blocks);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_audio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_audio.c
@@ -577,6 +577,18 @@
 	.i2s = 1,
 };
 
+void dp_unregister_audio_driver(struct device *dev, struct dp_audio *dp_audio)
+{
+	struct dp_audio_private *audio_priv;
+
+	audio_priv = container_of(dp_audio, struct dp_audio_private, dp_audio);
+
+	if (audio_priv->audio_pdev) {
+		platform_device_unregister(audio_priv->audio_pdev);
+		audio_priv->audio_pdev = NULL;
+	}
+}
+
 int dp_register_audio_driver(struct device *dev,
 		struct dp_audio *dp_audio)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_audio.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_audio.h
@@ -53,6 +53,8 @@
 int dp_register_audio_driver(struct device *dev,
 		struct dp_audio *dp_audio);
 
+void dp_unregister_audio_driver(struct device *dev, struct dp_audio *dp_audio);
+
 /**
  * dp_audio_put()
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_aux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_aux.c
@@ -33,6 +33,7 @@
 	bool read;
 	bool no_send_addr;
 	bool no_send_stop;
+	bool initted;
 	u32 offset;
 	u32 segment;
 
@@ -160,47 +161,6 @@
 	return i;
 }
 
-static void dp_aux_native_handler(struct dp_aux_private *aux, u32 isr)
-{
-	if (isr & DP_INTR_AUX_I2C_DONE)
-		aux->aux_error_num = DP_AUX_ERR_NONE;
-	else if (isr & DP_INTR_WRONG_ADDR)
-		aux->aux_error_num = DP_AUX_ERR_ADDR;
-	else if (isr & DP_INTR_TIMEOUT)
-		aux->aux_error_num = DP_AUX_ERR_TOUT;
-	if (isr & DP_INTR_NACK_DEFER)
-		aux->aux_error_num = DP_AUX_ERR_NACK;
-	if (isr & DP_INTR_AUX_ERROR) {
-		aux->aux_error_num = DP_AUX_ERR_PHY;
-		dp_catalog_aux_clear_hw_interrupts(aux->catalog);
-	}
-}
-
-static void dp_aux_i2c_handler(struct dp_aux_private *aux, u32 isr)
-{
-	if (isr & DP_INTR_AUX_I2C_DONE) {
-		if (isr & (DP_INTR_I2C_NACK | DP_INTR_I2C_DEFER))
-			aux->aux_error_num = DP_AUX_ERR_NACK;
-		else
-			aux->aux_error_num = DP_AUX_ERR_NONE;
-	} else {
-		if (isr & DP_INTR_WRONG_ADDR)
-			aux->aux_error_num = DP_AUX_ERR_ADDR;
-		else if (isr & DP_INTR_TIMEOUT)
-			aux->aux_error_num = DP_AUX_ERR_TOUT;
-		if (isr & DP_INTR_NACK_DEFER)
-			aux->aux_error_num = DP_AUX_ERR_NACK_DEFER;
-		if (isr & DP_INTR_I2C_NACK)
-			aux->aux_error_num = DP_AUX_ERR_NACK;
-		if (isr & DP_INTR_I2C_DEFER)
-			aux->aux_error_num = DP_AUX_ERR_DEFER;
-		if (isr & DP_INTR_AUX_ERROR) {
-			aux->aux_error_num = DP_AUX_ERR_PHY;
-			dp_catalog_aux_clear_hw_interrupts(aux->catalog);
-		}
-	}
-}
-
 static void dp_aux_update_offset_and_segment(struct dp_aux_private *aux,
 					     struct drm_dp_aux_msg *input_msg)
 {
@@ -331,6 +291,10 @@
 	}
 
 	mutex_lock(&aux->mutex);
+	if (!aux->initted) {
+		ret = -EIO;
+		goto exit;
+	}
 
 	dp_aux_update_offset_and_segment(aux, msg);
 	dp_aux_transfer_helper(aux, msg, true);
@@ -380,6 +344,8 @@
 	}
 
 	aux->cmd_busy = false;
+
+exit:
 	mutex_unlock(&aux->mutex);
 
 	return ret;
@@ -399,13 +365,46 @@
 
 	isr = dp_catalog_aux_get_irq(aux->catalog);
 
-	if (!aux->cmd_busy)
+	/* no interrupts pending, return immediately */
+	if (!isr)
 		return;
 
-	if (aux->native)
-		dp_aux_native_handler(aux, isr);
-	else
-		dp_aux_i2c_handler(aux, isr);
+	if (!aux->cmd_busy) {
+		DRM_ERROR("Unexpected DP AUX IRQ %#010x when not busy\n", isr);
+		return;
+	}
+
+	/*
+	 * The logic below assumes only one error bit is set (other than "done"
+	 * which can apparently be set at the same time as some of the other
+	 * bits). Warn if more than one get set so we know we need to improve
+	 * the logic.
+	 */
+	if (hweight32(isr & ~DP_INTR_AUX_XFER_DONE) > 1)
+		DRM_WARN("Some DP AUX interrupts unhandled: %#010x\n", isr);
+
+	if (isr & DP_INTR_AUX_ERROR) {
+		aux->aux_error_num = DP_AUX_ERR_PHY;
+		dp_catalog_aux_clear_hw_interrupts(aux->catalog);
+	} else if (isr & DP_INTR_NACK_DEFER) {
+		aux->aux_error_num = DP_AUX_ERR_NACK_DEFER;
+	} else if (isr & DP_INTR_WRONG_ADDR) {
+		aux->aux_error_num = DP_AUX_ERR_ADDR;
+	} else if (isr & DP_INTR_TIMEOUT) {
+		aux->aux_error_num = DP_AUX_ERR_TOUT;
+	} else if (!aux->native && (isr & DP_INTR_I2C_NACK)) {
+		aux->aux_error_num = DP_AUX_ERR_NACK;
+	} else if (!aux->native && (isr & DP_INTR_I2C_DEFER)) {
+		if (isr & DP_INTR_AUX_XFER_DONE)
+			aux->aux_error_num = DP_AUX_ERR_NACK;
+		else
+			aux->aux_error_num = DP_AUX_ERR_DEFER;
+	} else if (isr & DP_INTR_AUX_XFER_DONE) {
+		aux->aux_error_num = DP_AUX_ERR_NONE;
+	} else {
+		DRM_WARN("Unexpected interrupt: %#010x\n", isr);
+		return;
+	}
 
 	complete(&aux->comp);
 }
@@ -431,8 +430,13 @@
 
 	aux = container_of(dp_aux, struct dp_aux_private, dp_aux);
 
+	mutex_lock(&aux->mutex);
+
 	dp_catalog_aux_enable(aux->catalog, true);
 	aux->retry_cnt = 0;
+	aux->initted = true;
+
+	mutex_unlock(&aux->mutex);
 }
 
 void dp_aux_deinit(struct drm_dp_aux *dp_aux)
@@ -441,7 +445,12 @@
 
 	aux = container_of(dp_aux, struct dp_aux_private, dp_aux);
 
+	mutex_lock(&aux->mutex);
+
+	aux->initted = false;
 	dp_catalog_aux_enable(aux->catalog, false);
+
+	mutex_unlock(&aux->mutex);
 }
 
 int dp_aux_register(struct drm_dp_aux *dp_aux)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_catalog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_catalog.c
@@ -34,7 +34,7 @@
 #define MSM_DP_CONTROLLER_P0_SIZE	0x0400
 
 #define DP_INTERRUPT_STATUS1 \
-	(DP_INTR_AUX_I2C_DONE| \
+	(DP_INTR_AUX_XFER_DONE| \
 	DP_INTR_WRONG_ADDR | DP_INTR_TIMEOUT | \
 	DP_INTR_NACK_DEFER | DP_INTR_WRONG_DATA_CNT | \
 	DP_INTR_I2C_NACK | DP_INTR_I2C_DEFER | \
@@ -437,7 +437,7 @@
 
 	if (rate == link_rate_hbr3)
 		pixel_div = 6;
-	else if (rate == 1620000 || rate == 270000)
+	else if (rate == 162000 || rate == 270000)
 		pixel_div = 2;
 	else if (rate == link_rate_hbr2)
 		pixel_div = 4;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_catalog.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_catalog.h
@@ -13,7 +13,7 @@
 
 /* interrupts */
 #define DP_INTR_HPD		BIT(0)
-#define DP_INTR_AUX_I2C_DONE	BIT(3)
+#define DP_INTR_AUX_XFER_DONE	BIT(3)
 #define DP_INTR_WRONG_ADDR	BIT(6)
 #define DP_INTR_TIMEOUT		BIT(9)
 #define DP_INTR_NACK_DEFER	BIT(12)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_ctrl.c
@@ -1198,7 +1198,7 @@
 	if (ret)
 		return ret;
 
-	dp_ctrl_train_pattern_set(ctrl, pattern | DP_RECOVERED_CLOCK_OUT_EN);
+	dp_ctrl_train_pattern_set(ctrl, pattern);
 
 	for (tries = 0; tries <= maximum_retries; tries++) {
 		drm_dp_link_train_channel_eq_delay(ctrl->aux, ctrl->panel->dpcd);
@@ -1237,6 +1237,8 @@
 	link_info.rate = ctrl->link->link_params.rate;
 	link_info.capabilities = DP_LINK_CAP_ENHANCED_FRAMING;
 
+	dp_link_reset_phy_params_vx_px(ctrl->link);
+
 	dp_aux_link_configure(ctrl->aux, &link_info);
 	drm_dp_dpcd_write(ctrl->aux, DP_MAIN_LINK_CHANNEL_CODING_SET,
 				&encoding, 1);
@@ -1348,60 +1350,49 @@
 	return ret;
 }
 
-int dp_ctrl_host_init(struct dp_ctrl *dp_ctrl, bool flip, bool reset)
+void dp_ctrl_reset_irq_ctrl(struct dp_ctrl *dp_ctrl, bool enable)
+{
+	struct dp_ctrl_private *ctrl;
+
+	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
+
+	dp_catalog_ctrl_reset(ctrl->catalog);
+
+	/*
+	 * all dp controller programmable registers will not
+	 * be reset to default value after DP_SW_RESET
+	 * therefore interrupt mask bits have to be updated
+	 * to enable/disable interrupts
+	 */
+	dp_catalog_ctrl_enable_irq(ctrl->catalog, enable);
+}
+
+void dp_ctrl_phy_init(struct dp_ctrl *dp_ctrl)
 {
 	struct dp_ctrl_private *ctrl;
 	struct dp_io *dp_io;
 	struct phy *phy;
 
-	if (!dp_ctrl) {
-		DRM_ERROR("Invalid input data\n");
-		return -EINVAL;
-	}
-
 	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
 	dp_io = &ctrl->parser->io;
 	phy = dp_io->phy;
 
-	ctrl->dp_ctrl.orientation = flip;
-
-	if (reset)
-		dp_catalog_ctrl_reset(ctrl->catalog);
-
-	DRM_DEBUG_DP("flip=%d\n", flip);
 	dp_catalog_ctrl_phy_reset(ctrl->catalog);
 	phy_init(phy);
-	dp_catalog_ctrl_enable_irq(ctrl->catalog, true);
-
-	return 0;
 }
 
-/**
- * dp_ctrl_host_deinit() - Uninitialize DP controller
- * @dp_ctrl: Display Port Driver data
- *
- * Perform required steps to uninitialize DP controller
- * and its resources.
- */
-void dp_ctrl_host_deinit(struct dp_ctrl *dp_ctrl)
+void dp_ctrl_phy_exit(struct dp_ctrl *dp_ctrl)
 {
 	struct dp_ctrl_private *ctrl;
 	struct dp_io *dp_io;
 	struct phy *phy;
 
-	if (!dp_ctrl) {
-		DRM_ERROR("Invalid input data\n");
-		return;
-	}
-
 	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
 	dp_io = &ctrl->parser->io;
 	phy = dp_io->phy;
 
-	dp_catalog_ctrl_enable_irq(ctrl->catalog, false);
+	dp_catalog_ctrl_phy_reset(ctrl->catalog);
 	phy_exit(phy);
-
-	DRM_DEBUG_DP("Host deinitialized successfully\n");
 }
 
 static bool dp_ctrl_use_fixed_nvid(struct dp_ctrl_private *ctrl)
@@ -1471,7 +1462,10 @@
 	}
 
 	phy_power_off(phy);
+
+	/* aux channel down, reinit phy */
 	phy_exit(phy);
+	phy_init(phy);
 
 	return 0;
 }
@@ -1501,6 +1495,8 @@
 	return ret;
 }
 
+static int dp_ctrl_on_stream_phy_test_report(struct dp_ctrl *dp_ctrl);
+
 static int dp_ctrl_process_phy_test_request(struct dp_ctrl_private *ctrl)
 {
 	int ret = 0;
@@ -1515,7 +1511,7 @@
 	 * running. Add the global reset just before disabling the
 	 * link clocks and core clocks.
 	 */
-	ret = dp_ctrl_off_link_stream(&ctrl->dp_ctrl);
+	ret = dp_ctrl_off(&ctrl->dp_ctrl);
 	if (ret) {
 		DRM_ERROR("failed to disable DP controller\n");
 		return ret;
@@ -1523,7 +1519,7 @@
 
 	ret = dp_ctrl_on_link(&ctrl->dp_ctrl);
 	if (!ret)
-		ret = dp_ctrl_on_stream(&ctrl->dp_ctrl);
+		ret = dp_ctrl_on_stream_phy_test_report(&ctrl->dp_ctrl);
 	else
 		DRM_ERROR("failed to enable DP link controller\n");
 
@@ -1682,21 +1678,12 @@
 		ctrl->link->link_params.rate,
 		ctrl->link->link_params.num_lanes, ctrl->dp_ctrl.pixel_rate);
 
-	ctrl->link->phy_params.p_level = 0;
-	ctrl->link->phy_params.v_level = 0;
 
 	rc = dp_ctrl_enable_mainlink_clocks(ctrl);
 	if (rc)
 		return rc;
 
 	while (--link_train_max_retries) {
-		rc = dp_ctrl_reinitialize_mainlink(ctrl);
-		if (rc) {
-			DRM_ERROR("Failed to reinitialize mainlink. rc=%d\n",
-					rc);
-			break;
-		}
-
 		training_step = DP_TRAINING_NONE;
 		rc = dp_ctrl_setup_main_link(ctrl, &training_step);
 		if (rc == 0) {
@@ -1744,6 +1731,15 @@
 				/* end with failure */
 				break; /* lane == 1 already */
 			}
+
+			/* stop link training before start re training  */
+			dp_ctrl_clear_training_pattern(ctrl);
+		}
+
+		rc = dp_ctrl_reinitialize_mainlink(ctrl);
+		if (rc) {
+			DRM_ERROR("Failed to reinitialize mainlink. rc=%d\n", rc);
+			break;
 		}
 	}
 
@@ -1777,7 +1773,27 @@
 	return dp_ctrl_setup_main_link(ctrl, &training_step);
 }
 
-int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
+static int dp_ctrl_on_stream_phy_test_report(struct dp_ctrl *dp_ctrl)
+{
+	int ret;
+	struct dp_ctrl_private *ctrl;
+
+	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
+
+	ctrl->dp_ctrl.pixel_rate = ctrl->panel->dp_mode.drm_mode.clock;
+
+	ret = dp_ctrl_enable_stream_clocks(ctrl);
+	if (ret) {
+		DRM_ERROR("Failed to start pixel clocks. ret=%d\n", ret);
+		return ret;
+	}
+
+	dp_ctrl_send_phy_test_pattern(ctrl);
+
+	return 0;
+}
+
+int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl, bool force_link_train)
 {
 	int ret = 0;
 	bool mainlink_ready = false;
@@ -1802,22 +1818,17 @@
 		}
 	}
 
-	if (!dp_ctrl_channel_eq_ok(ctrl))
-		dp_ctrl_link_retrain(ctrl);
-
-	/* stop txing train pattern to end link training */
-	dp_ctrl_clear_training_pattern(ctrl);
-
 	ret = dp_ctrl_enable_stream_clocks(ctrl);
 	if (ret) {
 		DRM_ERROR("Failed to start pixel clocks. ret=%d\n", ret);
 		goto end;
 	}
 
-	if (ctrl->link->sink_request & DP_TEST_LINK_PHY_TEST_PATTERN) {
-		dp_ctrl_send_phy_test_pattern(ctrl);
-		return 0;
-	}
+	if (force_link_train || !dp_ctrl_channel_eq_ok(ctrl))
+		dp_ctrl_link_retrain(ctrl);
+
+	/* stop txing train pattern to end link training */
+	dp_ctrl_clear_training_pattern(ctrl);
 
 	/*
 	 * Set up transfer unit values and set controller state to send
@@ -1876,8 +1887,14 @@
 		return ret;
 	}
 
+	DRM_DEBUG_DP("Before, phy=%x init_count=%d power_on=%d\n",
+		(u32)(uintptr_t)phy, phy->init_count, phy->power_count);
+
 	phy_power_off(phy);
 
+	DRM_DEBUG_DP("After, phy=%x init_count=%d power_on=%d\n",
+		(u32)(uintptr_t)phy, phy->init_count, phy->power_count);
+
 	/* aux channel down, reinit phy */
 	phy_exit(phy);
 	phy_init(phy);
@@ -1886,23 +1903,6 @@
 	return ret;
 }
 
-void dp_ctrl_off_phy(struct dp_ctrl *dp_ctrl)
-{
-	struct dp_ctrl_private *ctrl;
-	struct dp_io *dp_io;
-	struct phy *phy;
-
-	ctrl = container_of(dp_ctrl, struct dp_ctrl_private, dp_ctrl);
-	dp_io = &ctrl->parser->io;
-	phy = dp_io->phy;
-
-	dp_catalog_ctrl_reset(ctrl->catalog);
-
-	phy_exit(phy);
-
-	DRM_DEBUG_DP("DP off phy done\n");
-}
-
 int dp_ctrl_off(struct dp_ctrl *dp_ctrl)
 {
 	struct dp_ctrl_private *ctrl;
@@ -1930,10 +1930,14 @@
 		DRM_ERROR("Failed to disable link clocks. ret=%d\n", ret);
 	}
 
+	DRM_DEBUG_DP("Before, phy=%x init_count=%d power_on=%d\n",
+		(u32)(uintptr_t)phy, phy->init_count, phy->power_count);
+
 	phy_power_off(phy);
-	phy_exit(phy);
 
-	DRM_DEBUG_DP("DP off done\n");
+	DRM_DEBUG_DP("After, phy=%x init_count=%d power_on=%d\n",
+		(u32)(uintptr_t)phy, phy->init_count, phy->power_count);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_ctrl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_ctrl.h
@@ -19,12 +19,9 @@
 	u32 pixel_rate;
 };
 
-int dp_ctrl_host_init(struct dp_ctrl *dp_ctrl, bool flip, bool reset);
-void dp_ctrl_host_deinit(struct dp_ctrl *dp_ctrl);
 int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl);
-int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl);
+int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl, bool force_link_train);
 int dp_ctrl_off_link_stream(struct dp_ctrl *dp_ctrl);
-void dp_ctrl_off_phy(struct dp_ctrl *dp_ctrl);
 int dp_ctrl_off(struct dp_ctrl *dp_ctrl);
 void dp_ctrl_push_idle(struct dp_ctrl *dp_ctrl);
 void dp_ctrl_isr(struct dp_ctrl *dp_ctrl);
@@ -34,4 +31,9 @@
 			struct dp_power *power, struct dp_catalog *catalog,
 			struct dp_parser *parser);
 
+void dp_ctrl_reset_irq_ctrl(struct dp_ctrl *dp_ctrl, bool enable);
+void dp_ctrl_phy_init(struct dp_ctrl *dp_ctrl);
+void dp_ctrl_phy_exit(struct dp_ctrl *dp_ctrl);
+void dp_ctrl_irq_phy_exit(struct dp_ctrl *dp_ctrl);
+
 #endif /* _DP_CTRL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_display.c
@@ -81,6 +81,7 @@
 
 	/* state variables */
 	bool core_initialized;
+	bool phy_initialized;
 	bool hpd_irq_on;
 	bool audio_supported;
 
@@ -110,6 +111,7 @@
 	u32 hpd_state;
 	u32 event_pndx;
 	u32 event_gndx;
+	struct task_struct *ev_tsk;
 	struct dp_event event_list[DP_EVENT_Q_MAX];
 	spinlock_t event_lock;
 
@@ -193,6 +195,8 @@
 	complete_all(&dp->audio_comp);
 }
 
+static int dp_hpd_event_thread_start(struct dp_display_private *dp_priv);
+
 static int dp_display_bind(struct device *dev, struct device *master,
 			   void *data)
 {
@@ -230,9 +234,18 @@
 	}
 
 	rc = dp_register_audio_driver(dev, dp->audio);
-	if (rc)
+	if (rc) {
 		DRM_ERROR("Audio registration Dp failed\n");
+		goto end;
+	}
+
+	rc = dp_hpd_event_thread_start(dp);
+	if (rc) {
+		DRM_ERROR("Event thread create failed\n");
+		goto end;
+	}
 
+	return 0;
 end:
 	return rc;
 }
@@ -247,7 +260,14 @@
 	dp = container_of(g_dp_display,
 			struct dp_display_private, dp_display);
 
+	/* disable all HPD interrupts */
+	if (dp->core_initialized)
+		dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_INT_MASK, false);
+
+	kthread_stop(dp->ev_tsk);
+
 	dp_power_client_deinit(dp->power);
+	dp_unregister_audio_driver(dev, dp->audio);
 	dp_aux_unregister(dp->aux);
 	priv->dp = NULL;
 }
@@ -344,36 +364,45 @@
 	return rc;
 }
 
-static void dp_display_host_init(struct dp_display_private *dp, int reset)
+static void dp_display_host_phy_init(struct dp_display_private *dp)
 {
-	bool flip = false;
+	DRM_DEBUG_DP("core_init=%d phy_init=%d\n",
+			dp->core_initialized, dp->phy_initialized);
 
-	DRM_DEBUG_DP("core_initialized=%d\n", dp->core_initialized);
-	if (dp->core_initialized) {
-		DRM_DEBUG_DP("DP core already initialized\n");
-		return;
+	if (!dp->phy_initialized) {
+		dp_ctrl_phy_init(dp->ctrl);
+		dp->phy_initialized = true;
 	}
+}
 
-	if (dp->usbpd->orientation == ORIENTATION_CC2)
-		flip = true;
+static void dp_display_host_phy_exit(struct dp_display_private *dp)
+{
+	DRM_DEBUG_DP("core_init=%d phy_init=%d\n",
+			dp->core_initialized, dp->phy_initialized);
 
-	dp_power_init(dp->power, flip);
-	dp_ctrl_host_init(dp->ctrl, flip, reset);
+	if (dp->phy_initialized) {
+		dp_ctrl_phy_exit(dp->ctrl);
+		dp->phy_initialized = false;
+	}
+}
+
+static void dp_display_host_init(struct dp_display_private *dp)
+{
+	DRM_DEBUG_DP("core_initialized=%d\n", dp->core_initialized);
+
+	dp_power_init(dp->power, false);
+	dp_ctrl_reset_irq_ctrl(dp->ctrl, true);
 	dp_aux_init(dp->aux);
 	dp->core_initialized = true;
 }
 
 static void dp_display_host_deinit(struct dp_display_private *dp)
 {
-	if (!dp->core_initialized) {
-		DRM_DEBUG_DP("DP core not initialized\n");
-		return;
-	}
+	DRM_DEBUG_DP("core_initialized=%d\n", dp->core_initialized);
 
-	dp_ctrl_host_deinit(dp->ctrl);
+	dp_ctrl_reset_irq_ctrl(dp->ctrl, false);
 	dp_aux_deinit(dp->aux);
 	dp_power_deinit(dp->power);
-
 	dp->core_initialized = false;
 }
 
@@ -391,7 +420,7 @@
 	dp = container_of(g_dp_display,
 			struct dp_display_private, dp_display);
 
-	dp_display_host_init(dp, false);
+	dp_display_host_phy_init(dp);
 
 	rc = dp_display_process_hpd_high(dp);
 end:
@@ -529,17 +558,9 @@
 
 	dp->hpd_state = ST_CONNECT_PENDING;
 
-	hpd->hpd_high = 1;
-
 	ret = dp_display_usbpd_configure_cb(&dp->pdev->dev);
 	if (ret) {	/* link train failed */
-		hpd->hpd_high = 0;
 		dp->hpd_state = ST_DISCONNECTED;
-
-		if (ret == -ECONNRESET) { /* cable unplugged */
-			dp->core_initialized = false;
-		}
-
 	} else {
 		/* start sentinel checking in case of missing uevent */
 		dp_add_event(dp, EV_CONNECT_PENDING_TIMEOUT, 0, tout);
@@ -609,9 +630,7 @@
 	if (state == ST_DISCONNECTED) {
 		/* triggered by irq_hdp with sink_count = 0 */
 		if (dp->link->sink_count == 0) {
-			dp_ctrl_off_phy(dp->ctrl);
-			hpd->hpd_high = 0;
-			dp->core_initialized = false;
+			dp_display_host_phy_exit(dp);
 		}
 		mutex_unlock(&dp->event_mutex);
 		return 0;
@@ -634,8 +653,6 @@
 	/* disable HPD plug interrupts */
 	dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, false);
 
-	hpd->hpd_high = 0;
-
 	/*
 	 * We don't need separate work for disconnect as
 	 * connect/attention interrupts are disabled
@@ -675,7 +692,6 @@
 static int dp_irq_hpd_handle(struct dp_display_private *dp, u32 data)
 {
 	u32 state;
-	int ret;
 
 	mutex_lock(&dp->event_mutex);
 
@@ -700,10 +716,8 @@
 		return 0;
 	}
 
-	ret = dp_display_usbpd_attention_cb(&dp->pdev->dev);
-	if (ret == -ECONNRESET) { /* cable unplugged */
-		dp->core_initialized = false;
-	}
+	dp_display_usbpd_attention_cb(&dp->pdev->dev);
+
 	DRM_DEBUG_DP("hpd_state=%d\n", state);
 
 	mutex_unlock(&dp->event_mutex);
@@ -827,7 +841,7 @@
 
 	dp = container_of(dp_display, struct dp_display_private, dp_display);
 
-	dp->panel->dp_mode.drm_mode = mode->drm_mode;
+	drm_mode_copy(&dp->panel->dp_mode.drm_mode, &mode->drm_mode);
 	dp->panel->dp_mode.bpp = mode->bpp;
 	dp->panel->dp_mode.capabilities = mode->capabilities;
 	dp_panel_init_panel_info(dp->panel);
@@ -852,7 +866,7 @@
 		return 0;
 	}
 
-	rc = dp_ctrl_on_stream(dp->ctrl);
+	rc = dp_ctrl_on_stream(dp->ctrl, data);
 	if (!rc)
 		dp_display->power_on = true;
 
@@ -898,12 +912,19 @@
 
 	dp_display->audio_enabled = false;
 
-	/* triggered by irq_hpd with sink_count = 0 */
 	if (dp->link->sink_count == 0) {
+		/*
+		 * irq_hpd with sink_count = 0
+		 * hdmi unplugged out of dongle
+		 */
 		dp_ctrl_off_link_stream(dp->ctrl);
 	} else {
+		/*
+		 * unplugged interrupt
+		 * dongle unplugged out of DUT
+		 */
 		dp_ctrl_off(dp->ctrl);
-		dp->core_initialized = false;
+		dp_display_host_phy_exit(dp);
 	}
 
 	dp_display->power_on = false;
@@ -1033,7 +1054,7 @@
 static void dp_display_config_hpd(struct dp_display_private *dp)
 {
 
-	dp_display_host_init(dp, true);
+	dp_display_host_init(dp);
 	dp_catalog_ctrl_hpd_config(dp->catalog);
 
 	/* Enable interrupt first time
@@ -1055,12 +1076,17 @@
 	while (1) {
 		if (timeout_mode) {
 			wait_event_timeout(dp_priv->event_q,
-				(dp_priv->event_pndx == dp_priv->event_gndx),
-						EVENT_TIMEOUT);
+				(dp_priv->event_pndx == dp_priv->event_gndx) ||
+					kthread_should_stop(), EVENT_TIMEOUT);
 		} else {
 			wait_event_interruptible(dp_priv->event_q,
-				(dp_priv->event_pndx != dp_priv->event_gndx));
+				(dp_priv->event_pndx != dp_priv->event_gndx) ||
+					kthread_should_stop());
 		}
+
+		if (kthread_should_stop())
+			break;
+
 		spin_lock_irqsave(&dp_priv->event_lock, flag);
 		todo = &dp_priv->event_list[dp_priv->event_gndx];
 		if (todo->delay) {
@@ -1130,12 +1156,17 @@
 	return 0;
 }
 
-static void dp_hpd_event_setup(struct dp_display_private *dp_priv)
+static int dp_hpd_event_thread_start(struct dp_display_private *dp_priv)
 {
-	init_waitqueue_head(&dp_priv->event_q);
-	spin_lock_init(&dp_priv->event_lock);
+	/* set event q to empty */
+	dp_priv->event_gndx = 0;
+	dp_priv->event_pndx = 0;
+
+	dp_priv->ev_tsk = kthread_run(hpd_event_thread, dp_priv, "dp_hpd_handler");
+	if (IS_ERR(dp_priv->ev_tsk))
+		return PTR_ERR(dp_priv->ev_tsk);
 
-	kthread_run(hpd_event_thread, dp_priv, "dp_hpd_handler");
+	return 0;
 }
 
 static irqreturn_t dp_display_irq_handler(int irq, void *dev_id)
@@ -1194,13 +1225,12 @@
 	dp = container_of(dp_display, struct dp_display_private, dp_display);
 
 	dp->irq = irq_of_parse_and_map(dp->pdev->dev.of_node, 0);
-	if (dp->irq < 0) {
-		rc = dp->irq;
-		DRM_ERROR("failed to get irq: %d\n", rc);
-		return rc;
+	if (!dp->irq) {
+		DRM_ERROR("failed to get irq\n");
+		return -EINVAL;
 	}
 
-	rc = devm_request_irq(&dp->pdev->dev, dp->irq,
+	rc = devm_request_irq(dp_display->drm_dev->dev, dp->irq,
 			dp_display_irq_handler,
 			IRQF_TRIGGER_HIGH, "dp_display_isr", dp);
 	if (rc < 0) {
@@ -1236,8 +1266,11 @@
 		return -EPROBE_DEFER;
 	}
 
+	/* setup event q */
 	mutex_init(&dp->event_mutex);
 	g_dp_display = &dp->dp_display;
+	init_waitqueue_head(&dp->event_q);
+	spin_lock_init(&dp->event_lock);
 
 	/* Store DP audio handle inside DP display */
 	g_dp_display->dp_audio = dp->audio;
@@ -1262,9 +1295,9 @@
 	dp = container_of(g_dp_display,
 			struct dp_display_private, dp_display);
 
+	component_del(&pdev->dev, &dp_display_comp_ops);
 	dp_display_deinit_sub_modules(dp);
 
-	component_del(&pdev->dev, &dp_display_comp_ops);
 	platform_set_drvdata(pdev, NULL);
 
 	return 0;
@@ -1288,20 +1321,23 @@
 	dp->hpd_state = ST_DISCONNECTED;
 
 	/* turn on dp ctrl/phy */
-	dp_display_host_init(dp, true);
+	dp_display_host_init(dp);
 
 	dp_catalog_ctrl_hpd_config(dp->catalog);
 
-	/*
-	 * set sink to normal operation mode -- D0
-	 * before dpcd read
-	 */
-	dp_link_psm_config(dp->link, &dp->panel->link_info, false);
 
 	if (dp_catalog_link_is_connected(dp->catalog)) {
+		/*
+		 * set sink to normal operation mode -- D0
+		 * before dpcd read
+		 */
+		dp_display_host_phy_init(dp);
+		dp_link_psm_config(dp->link, &dp->panel->link_info, false);
 		sink_count = drm_dp_read_sink_count(dp->aux);
 		if (sink_count < 0)
 			sink_count = 0;
+
+		dp_display_host_phy_exit(dp);
 	}
 
 	dp->link->sink_count = sink_count;
@@ -1340,18 +1376,16 @@
 	DRM_DEBUG_DP("Before, core_inited=%d power_on=%d\n",
 			dp->core_initialized, dp_display->power_on);
 
-	if (dp->core_initialized == true) {
-		/* mainlink enabled */
-		if (dp_power_clk_status(dp->power, DP_CTRL_PM))
-			dp_ctrl_off_link_stream(dp->ctrl);
-
-		dp_display_host_deinit(dp);
-	}
+	/* mainlink enabled */
+	if (dp_power_clk_status(dp->power, DP_CTRL_PM))
+		dp_ctrl_off_link_stream(dp->ctrl);
 
-	dp->hpd_state = ST_SUSPENDED;
+	dp_display_host_phy_exit(dp);
 
 	/* host_init will be called at pm_resume */
-	dp->core_initialized = false;
+	dp_display_host_deinit(dp);
+
+	dp->hpd_state = ST_SUSPENDED;
 
 	DRM_DEBUG_DP("After, core_inited=%d power_on=%d\n",
 			dp->core_initialized, dp_display->power_on);
@@ -1414,8 +1448,6 @@
 
 	dp = container_of(dp_display, struct dp_display_private, dp_display);
 
-	dp_hpd_event_setup(dp);
-
 	dp_add_event(dp, EV_HPD_INIT_SETUP, 0, 100);
 }
 
@@ -1442,6 +1474,7 @@
 			struct drm_encoder *encoder)
 {
 	struct msm_drm_private *priv;
+	struct dp_display_private *dp_priv;
 	int ret;
 
 	if (WARN_ON(!encoder) || WARN_ON(!dp_display) || WARN_ON(!dev))
@@ -1450,6 +1483,8 @@
 	priv = dev->dev_private;
 	dp_display->drm_dev = dev;
 
+	dp_priv = container_of(dp_display, struct dp_display_private, dp_display);
+
 	ret = dp_display_request_irq(dp_display);
 	if (ret) {
 		DRM_ERROR("request_irq failed, ret=%d\n", ret);
@@ -1467,6 +1502,8 @@
 		return ret;
 	}
 
+	dp_priv->panel->connector = dp_display->connector;
+
 	priv->connectors[priv->num_connectors++] = dp_display->connector;
 	return 0;
 }
@@ -1476,6 +1513,7 @@
 	int rc = 0;
 	struct dp_display_private *dp_display;
 	u32 state;
+	bool force_link_train = false;
 
 	dp_display = container_of(dp, struct dp_display_private, dp_display);
 	if (!dp_display->dp_mode.drm_mode.clock) {
@@ -1504,10 +1542,12 @@
 
 	state =  dp_display->hpd_state;
 
-	if (state == ST_DISPLAY_OFF)
-		dp_display_host_init(dp_display, true);
+	if (state == ST_DISPLAY_OFF) {
+		dp_display_host_phy_init(dp_display);
+		force_link_train = true;
+	}
 
-	dp_display_enable(dp_display, 0);
+	dp_display_enable(dp_display, force_link_train);
 
 	rc = dp_display_post_enable(dp);
 	if (rc) {
@@ -1516,10 +1556,6 @@
 		dp_display_unprepare(dp);
 	}
 
-	/* manual kick off plug event to train link */
-	if (state == ST_DISPLAY_OFF)
-		dp_add_event(dp_display, EV_IRQ_HPD_INT, 0, 0);
-
 	/* completed connection */
 	dp_display->hpd_state = ST_CONNECTED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_hpd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_hpd.c
@@ -32,8 +32,6 @@
 	hpd_priv = container_of(dp_usbpd, struct dp_hpd_private,
 					dp_usbpd);
 
-	dp_usbpd->hpd_high = hpd;
-
 	if (!hpd_priv->dp_cb || !hpd_priv->dp_cb->configure
 				|| !hpd_priv->dp_cb->disconnect) {
 		pr_err("hpd dp_cb not initialized\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_hpd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_hpd.h
@@ -26,7 +26,6 @@
  * @multi_func: multi-function preferred
  * @usb_config_req: request to switch to usb
  * @exit_dp_mode: request exit from displayport mode
- * @hpd_high: Hot Plug Detect signal is high.
  * @hpd_irq: Change in the status since last message
  * @alt_mode_cfg_done: bool to specify alt mode status
  * @debug_en: bool to specify debug mode
@@ -39,7 +38,6 @@
 	bool multi_func;
 	bool usb_config_req;
 	bool exit_dp_mode;
-	bool hpd_high;
 	bool hpd_irq;
 	bool alt_mode_cfg_done;
 	bool debug_en;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_link.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_link.c
@@ -7,6 +7,7 @@
 
 #include <drm/drm_print.h>
 
+#include "dp_reg.h"
 #include "dp_link.h"
 #include "dp_panel.h"
 
@@ -737,18 +738,25 @@
 	return 0;
 }
 
-static void dp_link_parse_sink_status_field(struct dp_link_private *link)
+static int dp_link_parse_sink_status_field(struct dp_link_private *link)
 {
 	int len = 0;
 
 	link->prev_sink_count = link->dp_link.sink_count;
-	dp_link_parse_sink_count(&link->dp_link);
+	len = dp_link_parse_sink_count(&link->dp_link);
+	if (len < 0) {
+		DRM_ERROR("DP parse sink count failed\n");
+		return len;
+	}
 
 	len = drm_dp_dpcd_read_link_status(link->aux,
 		link->link_status);
-	if (len < DP_LINK_STATUS_SIZE)
+	if (len < DP_LINK_STATUS_SIZE) {
 		DRM_ERROR("DP link status read failed\n");
-	dp_link_parse_request(link);
+		return len;
+	}
+
+	return dp_link_parse_request(link);
 }
 
 /**
@@ -1023,7 +1031,9 @@
 
 	dp_link_reset_data(link);
 
-	dp_link_parse_sink_status_field(link);
+	ret = dp_link_parse_sink_status_field(link);
+	if (ret)
+		return ret;
 
 	if (link->request.test_requested == DP_TEST_LINK_EDID_READ) {
 		dp_link->sink_request |= DP_TEST_LINK_EDID_READ;
@@ -1055,7 +1065,7 @@
 
 int dp_link_get_colorimetry_config(struct dp_link *dp_link)
 {
-	u32 cc;
+	u32 cc = DP_MISC0_COLORIMERY_CFG_LEGACY_RGB;
 	struct dp_link_private *link;
 
 	if (!dp_link) {
@@ -1069,10 +1079,11 @@
 	 * Unless a video pattern CTS test is ongoing, use RGB_VESA
 	 * Only RGB_VESA and RGB_CEA supported for now
 	 */
-	if (dp_link_is_video_pattern_requested(link))
-		cc = link->dp_link.test_video.test_dyn_range;
-	else
-		cc = DP_TEST_DYNAMIC_RANGE_VESA;
+	if (dp_link_is_video_pattern_requested(link)) {
+		if (link->dp_link.test_video.test_dyn_range &
+					DP_TEST_DYNAMIC_RANGE_CEA)
+			cc = DP_MISC0_COLORIMERY_CFG_CEA_RGB;
+	}
 
 	return cc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_panel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_panel.c
@@ -206,12 +206,6 @@
 			rc = -ETIMEDOUT;
 			goto end;
 		}
-
-		/* fail safe edid */
-		mutex_lock(&connector->dev->mode_config.mutex);
-		if (drm_add_modes_noedid(connector, 640, 480))
-			drm_set_preferred_mode(connector, 640, 480);
-		mutex_unlock(&connector->dev->mode_config.mutex);
 	}
 
 	if (panel->aux_cfg_update_done) {
@@ -269,26 +263,9 @@
 
 static u8 dp_panel_get_edid_checksum(struct edid *edid)
 {
-	struct edid *last_block;
-	u8 *raw_edid;
-	bool is_edid_corrupt = false;
-
-	if (!edid) {
-		DRM_ERROR("invalid edid input\n");
-		return 0;
-	}
-
-	raw_edid = (u8 *)edid;
-	raw_edid += (edid->extensions * EDID_LENGTH);
-	last_block = (struct edid *)raw_edid;
-
-	/* block type extension */
-	drm_edid_block_valid(raw_edid, 1, false, &is_edid_corrupt);
-	if (!is_edid_corrupt)
-		return last_block->checksum;
+	edid += edid->extensions;
 
-	DRM_ERROR("Invalid block, no checksum\n");
-	return 0;
+	return edid->checksum;
 }
 
 void dp_panel_handle_sink_request(struct dp_panel *dp_panel)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dp/dp_reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dp/dp_reg.h
@@ -129,6 +129,9 @@
 #define DP_MISC0_COLORIMETRY_CFG_SHIFT		(0x00000001)
 #define DP_MISC0_TEST_BITS_DEPTH_SHIFT		(0x00000005)
 
+#define DP_MISC0_COLORIMERY_CFG_LEGACY_RGB	(0)
+#define DP_MISC0_COLORIMERY_CFG_CEA_RGB		(0x04)
+
 #define REG_DP_VALID_BOUNDARY			(0x00000030)
 #define REG_DP_VALID_BOUNDARY_2			(0x00000034)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/dsi.c
@@ -40,7 +40,12 @@
 
 	of_node_put(phy_node);
 
-	if (!phy_pdev || !msm_dsi->phy) {
+	if (!phy_pdev) {
+		DRM_DEV_ERROR(&pdev->dev, "%s: phy driver is not ready\n", __func__);
+		return -EPROBE_DEFER;
+	}
+	if (!msm_dsi->phy) {
+		put_device(&phy_pdev->dev);
 		DRM_DEV_ERROR(&pdev->dev, "%s: phy driver is not ready\n", __func__);
 		return -EPROBE_DEFER;
 	}
@@ -207,6 +212,12 @@
 		return -EINVAL;
 
 	priv = dev->dev_private;
+
+	if (priv->num_bridges == ARRAY_SIZE(priv->bridges)) {
+		DRM_DEV_ERROR(dev->dev, "too many bridges\n");
+		return -ENOSPC;
+	}
+
 	msm_dsi->dev = dev;
 
 	ret = msm_dsi_host_modeset_init(msm_dsi->host, dev);
@@ -215,9 +226,13 @@
 		goto fail;
 	}
 
-	if (!msm_dsi_manager_validate_current_config(msm_dsi->id)) {
-		ret = -EINVAL;
-		goto fail;
+	if (msm_dsi_is_bonded_dsi(msm_dsi) &&
+	    !msm_dsi_is_master_dsi(msm_dsi)) {
+		/*
+		 * Do not return an eror here,
+		 * Just skip creating encoder/connector for the slave-DSI.
+		 */
+		return 0;
 	}
 
 	msm_dsi->encoder = encoder;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/dsi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/dsi.h
@@ -82,7 +82,6 @@
 bool msm_dsi_manager_cmd_xfer_trigger(int id, u32 dma_base, u32 len);
 int msm_dsi_manager_register(struct msm_dsi *msm_dsi);
 void msm_dsi_manager_unregister(struct msm_dsi *msm_dsi);
-bool msm_dsi_manager_validate_current_config(u8 id);
 void msm_dsi_manager_tpg_enable(void);
 
 /* msm dsi */
@@ -107,6 +106,8 @@
 					u32 dma_base, u32 len);
 int msm_dsi_host_enable(struct mipi_dsi_host *host);
 int msm_dsi_host_disable(struct mipi_dsi_host *host);
+void msm_dsi_host_enable_irq(struct mipi_dsi_host *host);
+void msm_dsi_host_disable_irq(struct mipi_dsi_host *host);
 int msm_dsi_host_power_on(struct mipi_dsi_host *host,
 			struct msm_dsi_phy_shared_timings *phy_shared_timings,
 			bool is_bonded_dsi, struct msm_dsi_phy *phy);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/dsi_cfg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/dsi_cfg.c
@@ -109,7 +109,7 @@
 static const struct msm_dsi_config msm8996_dsi_cfg = {
 	.io_offset = DSI_6G_REG_SHIFT,
 	.reg_cfg = {
-		.num = 2,
+		.num = 3,
 		.regs = {
 			{"vdda", 18160, 1 },	/* 1.25 V */
 			{"vcca", 17000, 32 },	/* 0.925 V */
@@ -148,7 +148,7 @@
 static const struct msm_dsi_config sdm660_dsi_cfg = {
 	.io_offset = DSI_6G_REG_SHIFT,
 	.reg_cfg = {
-		.num = 2,
+		.num = 1,
 		.regs = {
 			{"vdda", 12560, 4 },	/* 1.2 V */
 		},
@@ -209,8 +209,8 @@
 	},
 	.bus_clk_names = dsi_sc7280_bus_clk_names,
 	.num_bus_clks = ARRAY_SIZE(dsi_sc7280_bus_clk_names),
-	.io_start = { 0xae94000 },
-	.num_dsi = 1,
+	.io_start = { 0xae94000, 0xae96000 },
+	.num_dsi = 2,
 };
 
 static const struct msm_dsi_host_cfg_ops msm_dsi_v2_host_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -115,16 +115,16 @@
 	struct clk *pixel_clk_src;
 	struct clk *byte_intf_clk;
 
-	u32 byte_clk_rate;
-	u32 pixel_clk_rate;
-	u32 esc_clk_rate;
+	unsigned long byte_clk_rate;
+	unsigned long pixel_clk_rate;
+	unsigned long esc_clk_rate;
 
 	/* DSI v2 specific clocks */
 	struct clk *src_clk;
 	struct clk *esc_clk_src;
 	struct clk *dsi_clk_src;
 
-	u32 src_clk_rate;
+	unsigned long src_clk_rate;
 
 	struct gpio_desc *disp_en_gpio;
 	struct gpio_desc *te_gpio;
@@ -498,11 +498,11 @@
 
 int dsi_link_clk_set_rate_6g(struct msm_dsi_host *msm_host)
 {
-	u32 byte_intf_rate;
+	unsigned long byte_intf_rate;
 	int ret;
 
-	DBG("Set clk rates: pclk=%d, byteclk=%d",
-		msm_host->mode->clock, msm_host->byte_clk_rate);
+	DBG("Set clk rates: pclk=%lu, byteclk=%lu",
+	    msm_host->pixel_clk_rate, msm_host->byte_clk_rate);
 
 	ret = dev_pm_opp_set_rate(&msm_host->pdev->dev,
 				  msm_host->byte_clk_rate);
@@ -583,9 +583,9 @@
 {
 	int ret;
 
-	DBG("Set clk rates: pclk=%d, byteclk=%d, esc_clk=%d, dsi_src_clk=%d",
-		msm_host->mode->clock, msm_host->byte_clk_rate,
-		msm_host->esc_clk_rate, msm_host->src_clk_rate);
+	DBG("Set clk rates: pclk=%lu, byteclk=%lu, esc_clk=%lu, dsi_src_clk=%lu",
+	    msm_host->pixel_clk_rate, msm_host->byte_clk_rate,
+	    msm_host->esc_clk_rate, msm_host->src_clk_rate);
 
 	ret = clk_set_rate(msm_host->byte_clk, msm_host->byte_clk_rate);
 	if (ret) {
@@ -673,12 +673,12 @@
 	clk_disable_unprepare(msm_host->byte_clk);
 }
 
-static u32 dsi_get_pclk_rate(struct msm_dsi_host *msm_host, bool is_bonded_dsi)
+static unsigned long dsi_get_pclk_rate(struct msm_dsi_host *msm_host, bool is_bonded_dsi)
 {
 	struct drm_display_mode *mode = msm_host->mode;
-	u32 pclk_rate;
+	unsigned long pclk_rate;
 
-	pclk_rate = mode->clock * 1000;
+	pclk_rate = mode->clock * 1000u;
 
 	/*
 	 * For bonded DSI mode, the current DRM mode has the complete width of the
@@ -696,7 +696,7 @@
 {
 	u8 lanes = msm_host->lanes;
 	u32 bpp = dsi_get_bpp(msm_host->format);
-	u32 pclk_rate = dsi_get_pclk_rate(msm_host, is_bonded_dsi);
+	unsigned long pclk_rate = dsi_get_pclk_rate(msm_host, is_bonded_dsi);
 	u64 pclk_bpp = (u64)pclk_rate * bpp;
 
 	if (lanes == 0) {
@@ -713,7 +713,7 @@
 	msm_host->pixel_clk_rate = pclk_rate;
 	msm_host->byte_clk_rate = pclk_bpp;
 
-	DBG("pclk=%d, bclk=%d", msm_host->pixel_clk_rate,
+	DBG("pclk=%lu, bclk=%lu", msm_host->pixel_clk_rate,
 				msm_host->byte_clk_rate);
 
 }
@@ -772,7 +772,7 @@
 
 	msm_host->esc_clk_rate = msm_host->byte_clk_rate / esc_div;
 
-	DBG("esc=%d, src=%d", msm_host->esc_clk_rate,
+	DBG("esc=%lu, src=%lu", msm_host->esc_clk_rate,
 		msm_host->src_clk_rate);
 
 	return 0;
@@ -1079,9 +1079,21 @@
 
 static void dsi_wait4video_eng_busy(struct msm_dsi_host *msm_host)
 {
+	u32 data;
+
 	if (!(msm_host->mode_flags & MIPI_DSI_MODE_VIDEO))
 		return;
 
+	data = dsi_read(msm_host, REG_DSI_STATUS0);
+
+	/* if video mode engine is not busy, its because
+	 * either timing engine was not turned on or the
+	 * DSI controller has finished transmitting the video
+	 * data already, so no need to wait in those cases
+	 */
+	if (!(data & DSI_STATUS0_VIDEO_MODE_ENGINE_BUSY))
+		return;
+
 	if (msm_host->power_on && msm_host->enabled) {
 		dsi_wait4video_done(msm_host);
 		/* delay 4 ms to skip BLLP */
@@ -1142,8 +1154,7 @@
 
 	priv = dev->dev_private;
 	if (msm_host->tx_gem_obj) {
-		msm_gem_unpin_iova(msm_host->tx_gem_obj, priv->kms->aspace);
-		drm_gem_object_put(msm_host->tx_gem_obj);
+		msm_gem_kernel_put(msm_host->tx_gem_obj, priv->kms->aspace);
 		msm_host->tx_gem_obj = NULL;
 	}
 
@@ -1375,10 +1386,10 @@
 			dsi_get_bpp(msm_host->format) / 8;
 
 	len = dsi_cmd_dma_add(msm_host, msg);
-	if (!len) {
+	if (len < 0) {
 		pr_err("%s: failed to add cmd type = 0x%x\n",
 			__func__,  msg->type);
-		return -EINVAL;
+		return len;
 	}
 
 	/* for video mode, do not send cmds more than
@@ -1397,10 +1408,14 @@
 	}
 
 	ret = dsi_cmd_dma_tx(msm_host, len);
-	if (ret < len) {
-		pr_err("%s: cmd dma tx failed, type=0x%x, data0=0x%x, len=%d\n",
-			__func__, msg->type, (*(u8 *)(msg->tx_buf)), len);
-		return -ECOMM;
+	if (ret < 0) {
+		pr_err("%s: cmd dma tx failed, type=0x%x, data0=0x%x, len=%d, ret=%d\n",
+			__func__, msg->type, (*(u8 *)(msg->tx_buf)), len, ret);
+		return ret;
+	} else if (ret < len) {
+		pr_err("%s: cmd dma tx failed, type=0x%x, data0=0x%x, ret=%d len=%d\n",
+			__func__, msg->type, (*(u8 *)(msg->tx_buf)), ret, len);
+		return -EIO;
 	}
 
 	return len;
@@ -1696,6 +1711,8 @@
 	if (!prop) {
 		DRM_DEV_DEBUG(dev,
 			"failed to find data lane mapping, using default\n");
+		/* Set the number of date lanes to 4 by default. */
+		msm_host->num_data_lanes = 4;
 		return 0;
 	}
 
@@ -1898,6 +1915,22 @@
 		return ret;
 	}
 
+	msm_host->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
+	if (!msm_host->irq) {
+		dev_err(&pdev->dev, "failed to get irq\n");
+		return -EINVAL;
+	}
+
+	/* do not autoenable, will be enabled later */
+	ret = devm_request_irq(&pdev->dev, msm_host->irq, dsi_host_irq,
+			IRQF_TRIGGER_HIGH | IRQF_NO_AUTOEN,
+			"dsi_isr", msm_host);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to request IRQ%u: %d\n",
+				msm_host->irq, ret);
+		return ret;
+	}
+
 	init_completion(&msm_host->dma_comp);
 	init_completion(&msm_host->video_comp);
 	mutex_init(&msm_host->dev_mutex);
@@ -1906,6 +1939,9 @@
 
 	/* setup workqueue */
 	msm_host->workqueue = alloc_ordered_workqueue("dsi_drm_work", 0);
+	if (!msm_host->workqueue)
+		return -ENOMEM;
+
 	INIT_WORK(&msm_host->err_work, dsi_err_worker);
 	INIT_WORK(&msm_host->hpd_work, dsi_hpd_worker);
 
@@ -1941,25 +1977,8 @@
 {
 	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
 	const struct msm_dsi_cfg_handler *cfg_hnd = msm_host->cfg_hnd;
-	struct platform_device *pdev = msm_host->pdev;
 	int ret;
 
-	msm_host->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
-	if (msm_host->irq < 0) {
-		ret = msm_host->irq;
-		DRM_DEV_ERROR(dev->dev, "failed to get irq: %d\n", ret);
-		return ret;
-	}
-
-	ret = devm_request_irq(&pdev->dev, msm_host->irq,
-			dsi_host_irq, IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
-			"dsi_isr", msm_host);
-	if (ret < 0) {
-		DRM_DEV_ERROR(&pdev->dev, "failed to request IRQ%u: %d\n",
-				msm_host->irq, ret);
-		return ret;
-	}
-
 	msm_host->dev = dev;
 	ret = cfg_hnd->ops->tx_buf_alloc(msm_host, SZ_4K);
 	if (ret) {
@@ -2133,9 +2152,12 @@
 		}
 
 		ret = dsi_cmds2buf_tx(msm_host, msg);
-		if (ret < msg->tx_len) {
+		if (ret < 0) {
 			pr_err("%s: Read cmd Tx failed, %d\n", __func__, ret);
 			return ret;
+		} else if (ret < msg->tx_len) {
+			pr_err("%s: Read cmd Tx failed, too short: %d\n", __func__, ret);
+			return -ECOMM;
 		}
 
 		/*
@@ -2315,6 +2337,20 @@
 	clk_req->escclk_rate = msm_host->esc_clk_rate;
 }
 
+void msm_dsi_host_enable_irq(struct mipi_dsi_host *host)
+{
+	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
+
+	enable_irq(msm_host->irq);
+}
+
+void msm_dsi_host_disable_irq(struct mipi_dsi_host *host)
+{
+	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
+
+	disable_irq(msm_host->irq);
+}
+
 int msm_dsi_host_enable(struct mipi_dsi_host *host)
 {
 	struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/dsi_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/dsi_manager.c
@@ -377,6 +377,14 @@
 		}
 	}
 
+	/*
+	 * Enable before preparing the panel, disable after unpreparing, so
+	 * that the panel can communicate over the DSI link.
+	 */
+	msm_dsi_host_enable_irq(host);
+	if (is_bonded_dsi && msm_dsi1)
+		msm_dsi_host_enable_irq(msm_dsi1->host);
+
 	/* Always call panel functions once, because even for dual panels,
 	 * there is only one drm_panel instance.
 	 */
@@ -411,6 +419,10 @@
 	if (panel)
 		drm_panel_unprepare(panel);
 panel_prep_fail:
+	msm_dsi_host_disable_irq(host);
+	if (is_bonded_dsi && msm_dsi1)
+		msm_dsi_host_disable_irq(msm_dsi1->host);
+
 	if (is_bonded_dsi && msm_dsi1)
 		msm_dsi_host_power_off(msm_dsi1->host);
 host1_on_fail:
@@ -523,6 +535,10 @@
 								id, ret);
 	}
 
+	msm_dsi_host_disable_irq(host);
+	if (is_bonded_dsi && msm_dsi1)
+		msm_dsi_host_disable_irq(msm_dsi1->host);
+
 	/* Save PHY status if it is a clock source */
 	msm_dsi_phy_pll_save_state(msm_dsi->phy);
 
@@ -627,27 +643,10 @@
 	return connector;
 
 fail:
-	connector->funcs->destroy(msm_dsi->connector);
+	connector->funcs->destroy(connector);
 	return ERR_PTR(ret);
 }
 
-bool msm_dsi_manager_validate_current_config(u8 id)
-{
-	bool is_bonded_dsi = IS_BONDED_DSI();
-
-	/*
-	 * For bonded DSI, we only have one drm panel. For this
-	 * use case, we register only one bridge/connector.
-	 * Skip bridge/connector initialisation if it is
-	 * slave-DSI for bonded DSI configuration.
-	 */
-	if (is_bonded_dsi && !IS_MASTER_DSI_LINK(id)) {
-		DBG("Skip bridge registration for slave DSI->id: %d\n", id);
-		return false;
-	}
-	return true;
-}
-
 /* initialize bridge */
 struct drm_bridge *msm_dsi_manager_bridge_init(u8 id)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
@@ -347,7 +347,7 @@
 	} else {
 		timing->shared_timings.clk_pre =
 			linear_inter(tmax, tmin, pcnt2, 0, false);
-			timing->shared_timings.clk_pre_inc_by_2 = 0;
+		timing->shared_timings.clk_pre_inc_by_2 = 0;
 	}
 
 	timing->ta_go = 3;
@@ -588,7 +588,9 @@
 	struct device *dev = &phy->pdev->dev;
 	int ret;
 
-	pm_runtime_get_sync(dev);
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret)
+		return ret;
 
 	ret = clk_prepare_enable(phy->ahb_clk);
 	if (ret) {
@@ -750,6 +752,10 @@
 		goto fail;
 	}
 
+	ret = devm_pm_runtime_enable(&pdev->dev);
+	if (ret)
+		return ret;
+
 	/* PLL init will call into clk_register which requires
 	 * register access, so we need to enable power and ahb clock.
 	 */
@@ -806,12 +812,14 @@
 			struct msm_dsi_phy_clk_request *clk_req,
 			struct msm_dsi_phy_shared_timings *shared_timings)
 {
-	struct device *dev = &phy->pdev->dev;
+	struct device *dev;
 	int ret;
 
 	if (!phy || !phy->cfg->ops.enable)
 		return -EINVAL;
 
+	dev = &phy->pdev->dev;
+
 	ret = dsi_phy_enable_resource(phy);
 	if (ret) {
 		DRM_DEV_ERROR(dev, "%s: resource enable failed, %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c
@@ -562,7 +562,9 @@
 	char clk_name[32], parent[32], vco_name[32];
 	char parent2[32], parent3[32], parent4[32];
 	struct clk_init_data vco_init = {
-		.parent_names = (const char *[]){ "xo" },
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "ref",
+		},
 		.num_parents = 1,
 		.name = vco_name,
 		.flags = CLK_IGNORE_UNUSED,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/phy/dsi_phy_14nm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/phy/dsi_phy_14nm.c
@@ -541,6 +541,9 @@
 	if (unlikely(pll_14nm->phy->pll_on))
 		return 0;
 
+	if (dsi_pll_14nm_vco_recalc_rate(hw, VCO_REF_CLK_RATE) == 0)
+		dsi_pll_14nm_vco_set_rate(hw, pll_14nm->phy->cfg->min_pll_rate, VCO_REF_CLK_RATE);
+
 	dsi_phy_write(base + REG_DSI_14nm_PHY_PLL_VREF_CFG1, 0x10);
 	dsi_phy_write(cmn_base + REG_DSI_14nm_PHY_CMN_PLL_CNTRL, 1);
 
@@ -804,7 +807,9 @@
 {
 	char clk_name[32], parent[32], vco_name[32];
 	struct clk_init_data vco_init = {
-		.parent_names = (const char *[]){ "xo" },
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "ref",
+		},
 		.num_parents = 1,
 		.name = vco_name,
 		.flags = CLK_IGNORE_UNUSED,
@@ -1062,6 +1067,6 @@
 	},
 	.min_pll_rate = VCO_MIN_RATE,
 	.max_pll_rate = VCO_MAX_RATE,
-	.io_start = { 0xc994400, 0xc996000 },
+	.io_start = { 0xc994400, 0xc996400 },
 	.num_dsi_phy = 2,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm.c
@@ -521,7 +521,9 @@
 {
 	char clk_name[32], parent1[32], parent2[32], vco_name[32];
 	struct clk_init_data vco_init = {
-		.parent_names = (const char *[]){ "xo" },
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "ref", .name = "xo",
+		},
 		.num_parents = 1,
 		.name = vco_name,
 		.flags = CLK_IGNORE_UNUSED,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c
@@ -385,7 +385,9 @@
 {
 	char *clk_name, *parent_name, *vco_name;
 	struct clk_init_data vco_init = {
-		.parent_names = (const char *[]){ "pxo" },
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "ref",
+		},
 		.num_parents = 1,
 		.flags = CLK_IGNORE_UNUSED,
 		.ops = &clk_ops_dsi_pll_28nm_vco,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
@@ -590,7 +590,9 @@
 	char clk_name[32], parent[32], vco_name[32];
 	char parent2[32], parent3[32], parent4[32];
 	struct clk_init_data vco_init = {
-		.parent_names = (const char *[]){ "bi_tcxo" },
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "ref",
+		},
 		.num_parents = 1,
 		.name = vco_name,
 		.flags = CLK_IGNORE_UNUSED,
@@ -864,20 +866,26 @@
 	/* Alter PHY configurations if data rate less than 1.5GHZ*/
 	less_than_1500_mhz = (clk_req->bitclk_rate <= 1500000000);
 
-	/* For C-PHY, no low power settings for lower clk rate */
-	if (phy->cphy_mode)
-		less_than_1500_mhz = false;
-
 	if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1) {
 		vreg_ctrl_0 = less_than_1500_mhz ? 0x53 : 0x52;
-		glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d :  0x00;
-		glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x39 :  0x3c;
+		if (phy->cphy_mode) {
+			glbl_rescode_top_ctrl = 0x00;
+			glbl_rescode_bot_ctrl = 0x3c;
+		} else {
+			glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d :  0x00;
+			glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x39 :  0x3c;
+		}
 		glbl_str_swi_cal_sel_ctrl = 0x00;
 		glbl_hstx_str_ctrl_0 = 0x88;
 	} else {
 		vreg_ctrl_0 = less_than_1500_mhz ? 0x5B : 0x59;
-		glbl_str_swi_cal_sel_ctrl = less_than_1500_mhz ? 0x03 : 0x00;
-		glbl_hstx_str_ctrl_0 = less_than_1500_mhz ? 0x66 : 0x88;
+		if (phy->cphy_mode) {
+			glbl_str_swi_cal_sel_ctrl = 0x03;
+			glbl_hstx_str_ctrl_0 = 0x66;
+		} else {
+			glbl_str_swi_cal_sel_ctrl = less_than_1500_mhz ? 0x03 : 0x00;
+			glbl_hstx_str_ctrl_0 = less_than_1500_mhz ? 0x66 : 0x88;
+		}
 		glbl_rescode_top_ctrl = 0x03;
 		glbl_rescode_bot_ctrl = 0x3c;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/hdmi/hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/hdmi/hdmi.c
@@ -8,6 +8,8 @@
 #include <linux/of_irq.h>
 #include <linux/of_gpio.h>
 
+#include <drm/drm_bridge_connector.h>
+
 #include <sound/hdmi-codec.h>
 #include "hdmi.h"
 
@@ -41,7 +43,7 @@
 	struct hdmi *hdmi = dev_id;
 
 	/* Process HPD: */
-	msm_hdmi_connector_irq(hdmi->connector);
+	msm_hdmi_hpd_irq(hdmi->bridge);
 
 	/* Process DDC: */
 	msm_hdmi_i2c_irq(hdmi->i2c);
@@ -97,8 +99,13 @@
 
 	of_node_put(phy_node);
 
-	if (!phy_pdev || !hdmi->phy) {
+	if (!phy_pdev) {
+		DRM_DEV_ERROR(&pdev->dev, "phy driver is not ready\n");
+		return -EPROBE_DEFER;
+	}
+	if (!hdmi->phy) {
 		DRM_DEV_ERROR(&pdev->dev, "phy driver is not ready\n");
+		put_device(&phy_pdev->dev);
 		return -EPROBE_DEFER;
 	}
 
@@ -137,6 +144,10 @@
 	/* HDCP needs physical address of hdmi register */
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 		config->mmio_name);
+	if (!res) {
+		ret = -EINVAL;
+		goto fail;
+	}
 	hdmi->mmio_phy_addr = res->start;
 
 	hdmi->qfprom_mmio = msm_ioremap(pdev,
@@ -236,9 +247,27 @@
 		hdmi->pwr_clks[i] = clk;
 	}
 
-	pm_runtime_enable(&pdev->dev);
+	hdmi->hpd_gpiod = devm_gpiod_get_optional(&pdev->dev, "hpd", GPIOD_IN);
+	/* This will catch e.g. -EPROBE_DEFER */
+	if (IS_ERR(hdmi->hpd_gpiod)) {
+		ret = PTR_ERR(hdmi->hpd_gpiod);
+		DRM_DEV_ERROR(&pdev->dev, "failed to get hpd gpio: (%d)\n", ret);
+		goto fail;
+	}
+
+	if (!hdmi->hpd_gpiod)
+		DBG("failed to get HPD gpio");
+
+	if (hdmi->hpd_gpiod)
+		gpiod_set_consumer_name(hdmi->hpd_gpiod, "HDMI_HPD");
+
+	devm_pm_runtime_enable(&pdev->dev);
 
 	hdmi->workq = alloc_ordered_workqueue("msm_hdmi", 0);
+	if (!hdmi->workq) {
+		ret = -ENOMEM;
+		goto fail;
+	}
 
 	hdmi->i2c = msm_hdmi_i2c_init(hdmi);
 	if (IS_ERR(hdmi->i2c)) {
@@ -284,6 +313,11 @@
 	struct platform_device *pdev = hdmi->pdev;
 	int ret;
 
+	if (priv->num_bridges == ARRAY_SIZE(priv->bridges)) {
+		DRM_DEV_ERROR(dev->dev, "too many bridges\n");
+		return -ENOSPC;
+	}
+
 	hdmi->dev = dev;
 	hdmi->encoder = encoder;
 
@@ -297,7 +331,7 @@
 		goto fail;
 	}
 
-	hdmi->connector = msm_hdmi_connector_init(hdmi);
+	hdmi->connector = drm_bridge_connector_init(hdmi->dev, encoder);
 	if (IS_ERR(hdmi->connector)) {
 		ret = PTR_ERR(hdmi->connector);
 		DRM_DEV_ERROR(dev->dev, "failed to create HDMI connector: %d\n", ret);
@@ -305,15 +339,17 @@
 		goto fail;
 	}
 
+	drm_connector_attach_encoder(hdmi->connector, hdmi->encoder);
+
 	hdmi->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
-	if (hdmi->irq < 0) {
-		ret = hdmi->irq;
-		DRM_DEV_ERROR(dev->dev, "failed to get irq: %d\n", ret);
+	if (!hdmi->irq) {
+		ret = -EINVAL;
+		DRM_DEV_ERROR(dev->dev, "failed to get irq\n");
 		goto fail;
 	}
 
-	ret = devm_request_irq(&pdev->dev, hdmi->irq,
-			msm_hdmi_irq, IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+	ret = devm_request_irq(dev->dev, hdmi->irq,
+			msm_hdmi_irq, IRQF_TRIGGER_HIGH,
 			"hdmi_isr", hdmi);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dev->dev, "failed to request IRQ%u: %d\n",
@@ -321,7 +357,9 @@
 		goto fail;
 	}
 
-	ret = msm_hdmi_hpd_enable(hdmi->connector);
+	drm_bridge_connector_enable_hpd(hdmi->connector);
+
+	ret = msm_hdmi_hpd_enable(hdmi->bridge);
 	if (ret < 0) {
 		DRM_DEV_ERROR(&hdmi->pdev->dev, "failed to enable HPD: %d\n", ret);
 		goto fail;
@@ -409,20 +447,6 @@
 		.hpd_freq      = hpd_clk_freq_8x74,
 };
 
-static const struct {
-	const char *name;
-	const bool output;
-	const int value;
-	const char *label;
-} msm_hdmi_gpio_pdata[] = {
-	{ "qcom,hdmi-tx-ddc-clk", true, 1, "HDMI_DDC_CLK" },
-	{ "qcom,hdmi-tx-ddc-data", true, 1, "HDMI_DDC_DATA" },
-	{ "qcom,hdmi-tx-hpd", false, 1, "HDMI_HPD" },
-	{ "qcom,hdmi-tx-mux-en", true, 1, "HDMI_MUX_EN" },
-	{ "qcom,hdmi-tx-mux-sel", true, 0, "HDMI_MUX_SEL" },
-	{ "qcom,hdmi-tx-mux-lpm", true, 1, "HDMI_MUX_LPM" },
-};
-
 /*
  * HDMI audio codec callbacks
  */
@@ -535,7 +559,7 @@
 	struct hdmi_platform_config *hdmi_cfg;
 	struct hdmi *hdmi;
 	struct device_node *of_node = dev->of_node;
-	int i, err;
+	int err;
 
 	hdmi_cfg = (struct hdmi_platform_config *)
 			of_device_get_match_data(dev);
@@ -547,42 +571,6 @@
 	hdmi_cfg->mmio_name     = "core_physical";
 	hdmi_cfg->qfprom_mmio_name = "qfprom_physical";
 
-	for (i = 0; i < HDMI_MAX_NUM_GPIO; i++) {
-		const char *name = msm_hdmi_gpio_pdata[i].name;
-		struct gpio_desc *gpiod;
-
-		/*
-		 * We are fetching the GPIO lines "as is" since the connector
-		 * code is enabling and disabling the lines. Until that point
-		 * the power-on default value will be kept.
-		 */
-		gpiod = devm_gpiod_get_optional(dev, name, GPIOD_ASIS);
-		/* This will catch e.g. -PROBE_DEFER */
-		if (IS_ERR(gpiod))
-			return PTR_ERR(gpiod);
-		if (!gpiod) {
-			/* Try a second time, stripping down the name */
-			char name3[32];
-
-			/*
-			 * Try again after stripping out the "qcom,hdmi-tx"
-			 * prefix. This is mainly to match "hpd-gpios" used
-			 * in the upstream bindings.
-			 */
-			if (sscanf(name, "qcom,hdmi-tx-%s", name3))
-				gpiod = devm_gpiod_get_optional(dev, name3, GPIOD_ASIS);
-			if (IS_ERR(gpiod))
-				return PTR_ERR(gpiod);
-			if (!gpiod)
-				DBG("failed to get gpio: %s", name);
-		}
-		hdmi_cfg->gpios[i].gpiod = gpiod;
-		if (gpiod)
-			gpiod_set_consumer_name(gpiod, msm_hdmi_gpio_pdata[i].label);
-		hdmi_cfg->gpios[i].output = msm_hdmi_gpio_pdata[i].output;
-		hdmi_cfg->gpios[i].value = msm_hdmi_gpio_pdata[i].value;
-	}
-
 	dev->platform_data = hdmi_cfg;
 
 	hdmi = msm_hdmi_init(to_platform_device(dev));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/hdmi/hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/hdmi/hdmi.h
@@ -19,17 +19,9 @@
 #include "msm_drv.h"
 #include "hdmi.xml.h"
 
-#define HDMI_MAX_NUM_GPIO	6
-
 struct hdmi_phy;
 struct hdmi_platform_config;
 
-struct hdmi_gpio_data {
-	struct gpio_desc *gpiod;
-	bool output;
-	int value;
-};
-
 struct hdmi_audio {
 	bool enabled;
 	struct hdmi_audio_infoframe infoframe;
@@ -61,6 +53,8 @@
 	struct clk **hpd_clks;
 	struct clk **pwr_clks;
 
+	struct gpio_desc *hpd_gpiod;
+
 	struct hdmi_phy *phy;
 	struct device *phy_dev;
 
@@ -109,10 +103,14 @@
 	/* clks that need to be on for screen pwr (ie pixel clk): */
 	const char **pwr_clk_names;
 	int pwr_clk_cnt;
+};
 
-	/* gpio's: */
-	struct hdmi_gpio_data gpios[HDMI_MAX_NUM_GPIO];
+struct hdmi_bridge {
+	struct drm_bridge base;
+	struct hdmi *hdmi;
+	struct work_struct hpd_work;
 };
+#define to_hdmi_bridge(x) container_of(x, struct hdmi_bridge, base)
 
 void msm_hdmi_set_mode(struct hdmi *hdmi, bool power_on);
 
@@ -230,13 +228,11 @@
 struct drm_bridge *msm_hdmi_bridge_init(struct hdmi *hdmi);
 void msm_hdmi_bridge_destroy(struct drm_bridge *bridge);
 
-/*
- * hdmi connector:
- */
-
-void msm_hdmi_connector_irq(struct drm_connector *connector);
-struct drm_connector *msm_hdmi_connector_init(struct hdmi *hdmi);
-int msm_hdmi_hpd_enable(struct drm_connector *connector);
+void msm_hdmi_hpd_irq(struct drm_bridge *bridge);
+enum drm_connector_status msm_hdmi_bridge_detect(
+		struct drm_bridge *bridge);
+int msm_hdmi_hpd_enable(struct drm_bridge *bridge);
+void msm_hdmi_hpd_disable(struct hdmi_bridge *hdmi_bridge);
 
 /*
  * i2c adapter for ddc:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/hdmi/hdmi_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/hdmi/hdmi_bridge.c
@@ -5,17 +5,16 @@
  */
 
 #include <linux/delay.h>
+#include <drm/drm_bridge_connector.h>
 
+#include "msm_kms.h"
 #include "hdmi.h"
 
-struct hdmi_bridge {
-	struct drm_bridge base;
-	struct hdmi *hdmi;
-};
-#define to_hdmi_bridge(x) container_of(x, struct hdmi_bridge, base)
-
 void msm_hdmi_bridge_destroy(struct drm_bridge *bridge)
 {
+	struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
+
+	msm_hdmi_hpd_disable(hdmi_bridge);
 }
 
 static void msm_hdmi_power_on(struct drm_bridge *bridge)
@@ -259,14 +258,76 @@
 		msm_hdmi_audio_update(hdmi);
 }
 
+static struct edid *msm_hdmi_bridge_get_edid(struct drm_bridge *bridge,
+		struct drm_connector *connector)
+{
+	struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
+	struct hdmi *hdmi = hdmi_bridge->hdmi;
+	struct edid *edid;
+	uint32_t hdmi_ctrl;
+
+	hdmi_ctrl = hdmi_read(hdmi, REG_HDMI_CTRL);
+	hdmi_write(hdmi, REG_HDMI_CTRL, hdmi_ctrl | HDMI_CTRL_ENABLE);
+
+	edid = drm_get_edid(connector, hdmi->i2c);
+
+	hdmi_write(hdmi, REG_HDMI_CTRL, hdmi_ctrl);
+
+	hdmi->hdmi_mode = drm_detect_hdmi_monitor(edid);
+
+	return edid;
+}
+
+static enum drm_mode_status msm_hdmi_bridge_mode_valid(struct drm_bridge *bridge,
+		const struct drm_display_info *info,
+		const struct drm_display_mode *mode)
+{
+	struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
+	struct hdmi *hdmi = hdmi_bridge->hdmi;
+	const struct hdmi_platform_config *config = hdmi->config;
+	struct msm_drm_private *priv = bridge->dev->dev_private;
+	struct msm_kms *kms = priv->kms;
+	long actual, requested;
+
+	requested = 1000 * mode->clock;
+	actual = kms->funcs->round_pixclk(kms,
+			requested, hdmi_bridge->hdmi->encoder);
+
+	/* for mdp5/apq8074, we manage our own pixel clk (as opposed to
+	 * mdp4/dtv stuff where pixel clk is assigned to mdp/encoder
+	 * instead):
+	 */
+	if (config->pwr_clk_cnt > 0)
+		actual = clk_round_rate(hdmi->pwr_clks[0], actual);
+
+	DBG("requested=%ld, actual=%ld", requested, actual);
+
+	if (actual != requested)
+		return MODE_CLOCK_RANGE;
+
+	return 0;
+}
+
 static const struct drm_bridge_funcs msm_hdmi_bridge_funcs = {
 		.pre_enable = msm_hdmi_bridge_pre_enable,
 		.enable = msm_hdmi_bridge_enable,
 		.disable = msm_hdmi_bridge_disable,
 		.post_disable = msm_hdmi_bridge_post_disable,
 		.mode_set = msm_hdmi_bridge_mode_set,
+		.mode_valid = msm_hdmi_bridge_mode_valid,
+		.get_edid = msm_hdmi_bridge_get_edid,
+		.detect = msm_hdmi_bridge_detect,
 };
 
+static void
+msm_hdmi_hotplug_work(struct work_struct *work)
+{
+	struct hdmi_bridge *hdmi_bridge =
+		container_of(work, struct hdmi_bridge, hpd_work);
+	struct drm_bridge *bridge = &hdmi_bridge->base;
+
+	drm_bridge_hpd_notify(bridge, drm_bridge_detect(bridge));
+}
 
 /* initialize bridge */
 struct drm_bridge *msm_hdmi_bridge_init(struct hdmi *hdmi)
@@ -283,11 +344,17 @@
 	}
 
 	hdmi_bridge->hdmi = hdmi;
+	INIT_WORK(&hdmi_bridge->hpd_work, msm_hdmi_hotplug_work);
 
 	bridge = &hdmi_bridge->base;
 	bridge->funcs = &msm_hdmi_bridge_funcs;
+	bridge->ddc = hdmi->i2c;
+	bridge->type = DRM_MODE_CONNECTOR_HDMIA;
+	bridge->ops = DRM_BRIDGE_OP_HPD |
+		DRM_BRIDGE_OP_DETECT |
+		DRM_BRIDGE_OP_EDID;
 
-	ret = drm_bridge_attach(hdmi->encoder, bridge, NULL, 0);
+	ret = drm_bridge_attach(hdmi->encoder, bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
 	if (ret)
 		goto fail;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/hdmi/hdmi_hpd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/hdmi/hdmi_hpd.c
@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 Red Hat
+ * Author: Rob Clark <robdclark@gmail.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/pinctrl/consumer.h>
+
+#include "msm_kms.h"
+#include "hdmi.h"
+
+static void msm_hdmi_phy_reset(struct hdmi *hdmi)
+{
+	unsigned int val;
+
+	val = hdmi_read(hdmi, REG_HDMI_PHY_CTRL);
+
+	if (val & HDMI_PHY_CTRL_SW_RESET_LOW) {
+		/* pull low */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val & ~HDMI_PHY_CTRL_SW_RESET);
+	} else {
+		/* pull high */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val | HDMI_PHY_CTRL_SW_RESET);
+	}
+
+	if (val & HDMI_PHY_CTRL_SW_RESET_PLL_LOW) {
+		/* pull low */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val & ~HDMI_PHY_CTRL_SW_RESET_PLL);
+	} else {
+		/* pull high */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val | HDMI_PHY_CTRL_SW_RESET_PLL);
+	}
+
+	msleep(100);
+
+	if (val & HDMI_PHY_CTRL_SW_RESET_LOW) {
+		/* pull high */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val | HDMI_PHY_CTRL_SW_RESET);
+	} else {
+		/* pull low */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val & ~HDMI_PHY_CTRL_SW_RESET);
+	}
+
+	if (val & HDMI_PHY_CTRL_SW_RESET_PLL_LOW) {
+		/* pull high */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val | HDMI_PHY_CTRL_SW_RESET_PLL);
+	} else {
+		/* pull low */
+		hdmi_write(hdmi, REG_HDMI_PHY_CTRL,
+				val & ~HDMI_PHY_CTRL_SW_RESET_PLL);
+	}
+}
+
+static void enable_hpd_clocks(struct hdmi *hdmi, bool enable)
+{
+	const struct hdmi_platform_config *config = hdmi->config;
+	struct device *dev = &hdmi->pdev->dev;
+	int i, ret;
+
+	if (enable) {
+		for (i = 0; i < config->hpd_clk_cnt; i++) {
+			if (config->hpd_freq && config->hpd_freq[i]) {
+				ret = clk_set_rate(hdmi->hpd_clks[i],
+						   config->hpd_freq[i]);
+				if (ret)
+					dev_warn(dev,
+						 "failed to set clk %s (%d)\n",
+						 config->hpd_clk_names[i], ret);
+			}
+
+			ret = clk_prepare_enable(hdmi->hpd_clks[i]);
+			if (ret) {
+				DRM_DEV_ERROR(dev,
+					"failed to enable hpd clk: %s (%d)\n",
+					config->hpd_clk_names[i], ret);
+			}
+		}
+	} else {
+		for (i = config->hpd_clk_cnt - 1; i >= 0; i--)
+			clk_disable_unprepare(hdmi->hpd_clks[i]);
+	}
+}
+
+int msm_hdmi_hpd_enable(struct drm_bridge *bridge)
+{
+	struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
+	struct hdmi *hdmi = hdmi_bridge->hdmi;
+	const struct hdmi_platform_config *config = hdmi->config;
+	struct device *dev = &hdmi->pdev->dev;
+	uint32_t hpd_ctrl;
+	int i, ret;
+	unsigned long flags;
+
+	for (i = 0; i < config->hpd_reg_cnt; i++) {
+		ret = regulator_enable(hdmi->hpd_regs[i]);
+		if (ret) {
+			DRM_DEV_ERROR(dev, "failed to enable hpd regulator: %s (%d)\n",
+					config->hpd_reg_names[i], ret);
+			goto fail;
+		}
+	}
+
+	ret = pinctrl_pm_select_default_state(dev);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "pinctrl state chg failed: %d\n", ret);
+		goto fail;
+	}
+
+	if (hdmi->hpd_gpiod)
+		gpiod_set_value_cansleep(hdmi->hpd_gpiod, 1);
+
+	pm_runtime_get_sync(dev);
+	enable_hpd_clocks(hdmi, true);
+
+	msm_hdmi_set_mode(hdmi, false);
+	msm_hdmi_phy_reset(hdmi);
+	msm_hdmi_set_mode(hdmi, true);
+
+	hdmi_write(hdmi, REG_HDMI_USEC_REFTIMER, 0x0001001b);
+
+	/* enable HPD events: */
+	hdmi_write(hdmi, REG_HDMI_HPD_INT_CTRL,
+			HDMI_HPD_INT_CTRL_INT_CONNECT |
+			HDMI_HPD_INT_CTRL_INT_EN);
+
+	/* set timeout to 4.1ms (max) for hardware debounce */
+	spin_lock_irqsave(&hdmi->reg_lock, flags);
+	hpd_ctrl = hdmi_read(hdmi, REG_HDMI_HPD_CTRL);
+	hpd_ctrl |= HDMI_HPD_CTRL_TIMEOUT(0x1fff);
+
+	/* Toggle HPD circuit to trigger HPD sense */
+	hdmi_write(hdmi, REG_HDMI_HPD_CTRL,
+			~HDMI_HPD_CTRL_ENABLE & hpd_ctrl);
+	hdmi_write(hdmi, REG_HDMI_HPD_CTRL,
+			HDMI_HPD_CTRL_ENABLE | hpd_ctrl);
+	spin_unlock_irqrestore(&hdmi->reg_lock, flags);
+
+	return 0;
+
+fail:
+	return ret;
+}
+
+void msm_hdmi_hpd_disable(struct hdmi_bridge *hdmi_bridge)
+{
+	struct hdmi *hdmi = hdmi_bridge->hdmi;
+	const struct hdmi_platform_config *config = hdmi->config;
+	struct device *dev = &hdmi->pdev->dev;
+	int i, ret = 0;
+
+	/* Disable HPD interrupt */
+	hdmi_write(hdmi, REG_HDMI_HPD_INT_CTRL, 0);
+
+	msm_hdmi_set_mode(hdmi, false);
+
+	enable_hpd_clocks(hdmi, false);
+	pm_runtime_put_autosuspend(dev);
+
+	ret = pinctrl_pm_select_sleep_state(dev);
+	if (ret)
+		dev_warn(dev, "pinctrl state chg failed: %d\n", ret);
+
+	for (i = 0; i < config->hpd_reg_cnt; i++) {
+		ret = regulator_disable(hdmi->hpd_regs[i]);
+		if (ret)
+			dev_warn(dev, "failed to disable hpd regulator: %s (%d)\n",
+					config->hpd_reg_names[i], ret);
+	}
+}
+
+void msm_hdmi_hpd_irq(struct drm_bridge *bridge)
+{
+	struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
+	struct hdmi *hdmi = hdmi_bridge->hdmi;
+	uint32_t hpd_int_status, hpd_int_ctrl;
+
+	/* Process HPD: */
+	hpd_int_status = hdmi_read(hdmi, REG_HDMI_HPD_INT_STATUS);
+	hpd_int_ctrl   = hdmi_read(hdmi, REG_HDMI_HPD_INT_CTRL);
+
+	if ((hpd_int_ctrl & HDMI_HPD_INT_CTRL_INT_EN) &&
+			(hpd_int_status & HDMI_HPD_INT_STATUS_INT)) {
+		bool detected = !!(hpd_int_status & HDMI_HPD_INT_STATUS_CABLE_DETECTED);
+
+		/* ack & disable (temporarily) HPD events: */
+		hdmi_write(hdmi, REG_HDMI_HPD_INT_CTRL,
+			HDMI_HPD_INT_CTRL_INT_ACK);
+
+		DBG("status=%04x, ctrl=%04x", hpd_int_status, hpd_int_ctrl);
+
+		/* detect disconnect if we are connected or visa versa: */
+		hpd_int_ctrl = HDMI_HPD_INT_CTRL_INT_EN;
+		if (!detected)
+			hpd_int_ctrl |= HDMI_HPD_INT_CTRL_INT_CONNECT;
+		hdmi_write(hdmi, REG_HDMI_HPD_INT_CTRL, hpd_int_ctrl);
+
+		queue_work(hdmi->workq, &hdmi_bridge->hpd_work);
+	}
+}
+
+static enum drm_connector_status detect_reg(struct hdmi *hdmi)
+{
+	uint32_t hpd_int_status;
+
+	pm_runtime_get_sync(&hdmi->pdev->dev);
+	enable_hpd_clocks(hdmi, true);
+
+	hpd_int_status = hdmi_read(hdmi, REG_HDMI_HPD_INT_STATUS);
+
+	enable_hpd_clocks(hdmi, false);
+	pm_runtime_put_autosuspend(&hdmi->pdev->dev);
+
+	return (hpd_int_status & HDMI_HPD_INT_STATUS_CABLE_DETECTED) ?
+			connector_status_connected : connector_status_disconnected;
+}
+
+#define HPD_GPIO_INDEX	2
+static enum drm_connector_status detect_gpio(struct hdmi *hdmi)
+{
+	return gpiod_get_value(hdmi->hpd_gpiod) ?
+			connector_status_connected :
+			connector_status_disconnected;
+}
+
+enum drm_connector_status msm_hdmi_bridge_detect(
+		struct drm_bridge *bridge)
+{
+	struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
+	struct hdmi *hdmi = hdmi_bridge->hdmi;
+	enum drm_connector_status stat_gpio, stat_reg;
+	int retry = 20;
+
+	/*
+	 * some platforms may not have hpd gpio. Rely only on the status
+	 * provided by REG_HDMI_HPD_INT_STATUS in this case.
+	 */
+	if (!hdmi->hpd_gpiod)
+		return detect_reg(hdmi);
+
+	do {
+		stat_gpio = detect_gpio(hdmi);
+		stat_reg  = detect_reg(hdmi);
+
+		if (stat_gpio == stat_reg)
+			break;
+
+		mdelay(10);
+	} while (--retry);
+
+	/* the status we get from reading gpio seems to be more reliable,
+	 * so trust that one the most if we didn't manage to get hdmi and
+	 * gpio status to agree:
+	 */
+	if (stat_gpio != stat_reg) {
+		DBG("HDMI_HPD_INT_STATUS tells us: %d", stat_reg);
+		DBG("hpd gpio tells us: %d", stat_gpio);
+	}
+
+	return stat_gpio;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_atomic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_atomic.c
@@ -5,7 +5,6 @@
  */
 
 #include <drm/drm_atomic_uapi.h>
-#include <drm/drm_gem_atomic_helper.h>
 #include <drm/drm_vblank.h>
 
 #include "msm_atomic_trace.h"
@@ -13,20 +12,6 @@
 #include "msm_gem.h"
 #include "msm_kms.h"
 
-int msm_atomic_prepare_fb(struct drm_plane *plane,
-			  struct drm_plane_state *new_state)
-{
-	struct msm_drm_private *priv = plane->dev->dev_private;
-	struct msm_kms *kms = priv->kms;
-
-	if (!new_state->fb)
-		return 0;
-
-	drm_gem_plane_helper_prepare_fb(plane, new_state);
-
-	return msm_framebuffer_prepare(new_state->fb, kms->aspace);
-}
-
 /*
  * Helpers to control vblanks while we flush.. basically just to ensure
  * that vblank accounting is switched on, so we get valid seqn/timestamp
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_debugfs.c
@@ -29,14 +29,14 @@
 	struct msm_gpu *gpu = priv->gpu;
 	int ret;
 
-	ret = mutex_lock_interruptible(&show_priv->dev->struct_mutex);
+	ret = mutex_lock_interruptible(&gpu->lock);
 	if (ret)
 		return ret;
 
 	drm_printf(&p, "%s Status:\n", gpu->name);
 	gpu->funcs->show(gpu, show_priv->state, &p);
 
-	mutex_unlock(&show_priv->dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	return 0;
 }
@@ -48,9 +48,9 @@
 	struct msm_drm_private *priv = show_priv->dev->dev_private;
 	struct msm_gpu *gpu = priv->gpu;
 
-	mutex_lock(&show_priv->dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 	gpu->funcs->gpu_state_put(show_priv->state);
-	mutex_unlock(&show_priv->dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	kfree(show_priv);
 
@@ -72,15 +72,16 @@
 	if (!show_priv)
 		return -ENOMEM;
 
-	ret = mutex_lock_interruptible(&dev->struct_mutex);
+	ret = mutex_lock_interruptible(&gpu->lock);
 	if (ret)
 		goto free_priv;
 
 	pm_runtime_get_sync(&gpu->pdev->dev);
+	msm_gpu_hw_init(gpu);
 	show_priv->state = gpu->funcs->gpu_state_get(gpu);
 	pm_runtime_put_sync(&gpu->pdev->dev);
 
-	mutex_unlock(&dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	if (IS_ERR(show_priv->state)) {
 		ret = PTR_ERR(show_priv->state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_drv.c
@@ -11,6 +11,7 @@
 #include <linux/uaccess.h>
 #include <uapi/linux/sched/types.h>
 
+#include <drm/drm_bridge.h>
 #include <drm/drm_drv.h>
 #include <drm/drm_file.h>
 #include <drm/drm_ioctl.h>
@@ -236,6 +237,8 @@
 
 static int msm_irq_install(struct drm_device *dev, unsigned int irq)
 {
+	struct msm_drm_private *priv = dev->dev_private;
+	struct msm_kms *kms = priv->kms;
 	int ret;
 
 	if (irq == IRQ_NOTCONNECTED)
@@ -247,6 +250,8 @@
 	if (ret)
 		return ret;
 
+	kms->irq_requested = true;
+
 	ret = msm_irq_postinstall(dev);
 	if (ret) {
 		free_irq(irq, dev);
@@ -262,7 +267,8 @@
 	struct msm_kms *kms = priv->kms;
 
 	kms->funcs->irq_uninstall(kms);
-	free_irq(kms->irq, dev);
+	if (kms->irq_requested)
+		free_irq(kms->irq, dev);
 }
 
 struct msm_vblank_work {
@@ -353,13 +359,16 @@
 		msm_fbdev_free(ddev);
 #endif
 
-	msm_disp_snapshot_destroy(ddev);
+	if (kms)
+		msm_disp_snapshot_destroy(ddev);
 
 	drm_mode_config_cleanup(ddev);
 
-	pm_runtime_get_sync(dev);
-	msm_irq_uninstall(ddev);
-	pm_runtime_put_sync(dev);
+	if (kms) {
+		pm_runtime_get_sync(dev);
+		msm_irq_uninstall(ddev);
+		pm_runtime_put_sync(dev);
+	}
 
 	if (kms && kms->funcs)
 		kms->funcs->destroy(kms);
@@ -437,7 +446,7 @@
 		of_node_put(node);
 		if (ret)
 			return ret;
-		size = r.end - r.start;
+		size = r.end - r.start + 1;
 		DRM_INFO("using VRAM carveout: %lx@%pa\n", size, &r.start);
 
 		/* if we have no IOMMU, then we need to use carveout allocator.
@@ -603,7 +612,7 @@
 		if (IS_ERR(priv->event_thread[i].worker)) {
 			ret = PTR_ERR(priv->event_thread[i].worker);
 			DRM_DEV_ERROR(dev, "failed to create crtc_event kthread\n");
-			ret = PTR_ERR(priv->event_thread[i].worker);
+			priv->event_thread[i].worker = NULL;
 			goto err_msm_uninit;
 		}
 
@@ -723,14 +732,8 @@
 
 static void msm_postclose(struct drm_device *dev, struct drm_file *file)
 {
-	struct msm_drm_private *priv = dev->dev_private;
 	struct msm_file_private *ctx = file->driver_priv;
 
-	mutex_lock(&dev->struct_mutex);
-	if (ctx == priv->lastctx)
-		priv->lastctx = NULL;
-	mutex_unlock(&dev->struct_mutex);
-
 	context_close(ctx);
 }
 
@@ -938,29 +941,18 @@
 	return ret;
 }
 
-static int msm_ioctl_wait_fence(struct drm_device *dev, void *data,
-		struct drm_file *file)
+static int wait_fence(struct msm_gpu_submitqueue *queue, uint32_t fence_id,
+		      ktime_t timeout)
 {
-	struct msm_drm_private *priv = dev->dev_private;
-	struct drm_msm_wait_fence *args = data;
-	ktime_t timeout = to_ktime(args->timeout);
-	struct msm_gpu_submitqueue *queue;
-	struct msm_gpu *gpu = priv->gpu;
 	struct dma_fence *fence;
 	int ret;
 
-	if (args->pad) {
-		DRM_ERROR("invalid pad: %08x\n", args->pad);
+	if (fence_id > queue->last_fence) {
+		DRM_ERROR_RATELIMITED("waiting on invalid fence: %u (of %u)\n",
+				      fence_id, queue->last_fence);
 		return -EINVAL;
 	}
 
-	if (!gpu)
-		return 0;
-
-	queue = msm_submitqueue_get(file->driver_priv, args->queueid);
-	if (!queue)
-		return -ENOENT;
-
 	/*
 	 * Map submitqueue scoped "seqno" (which is actually an idr key)
 	 * back to underlying dma-fence
@@ -972,7 +964,7 @@
 	ret = mutex_lock_interruptible(&queue->lock);
 	if (ret)
 		return ret;
-	fence = idr_find(&queue->fence_idr, args->fence);
+	fence = idr_find(&queue->fence_idr, fence_id);
 	if (fence)
 		fence = dma_fence_get_rcu(fence);
 	mutex_unlock(&queue->lock);
@@ -988,6 +980,32 @@
 	}
 
 	dma_fence_put(fence);
+
+	return ret;
+}
+
+static int msm_ioctl_wait_fence(struct drm_device *dev, void *data,
+		struct drm_file *file)
+{
+	struct msm_drm_private *priv = dev->dev_private;
+	struct drm_msm_wait_fence *args = data;
+	struct msm_gpu_submitqueue *queue;
+	int ret;
+
+	if (args->pad) {
+		DRM_ERROR("invalid pad: %08x\n", args->pad);
+		return -EINVAL;
+	}
+
+	if (!priv->gpu)
+		return 0;
+
+	queue = msm_submitqueue_get(file->driver_priv, args->queueid);
+	if (!queue)
+		return -ENOENT;
+
+	ret = wait_fence(queue, args->fence, to_ktime(args->timeout));
+
 	msm_submitqueue_put(queue);
 
 	return ret;
@@ -1081,7 +1099,7 @@
 	.prime_handle_to_fd = drm_gem_prime_handle_to_fd,
 	.prime_fd_to_handle = drm_gem_prime_fd_to_handle,
 	.gem_prime_import_sg_table = msm_gem_prime_import_sg_table,
-	.gem_prime_mmap     = drm_gem_prime_mmap,
+	.gem_prime_mmap     = msm_gem_prime_mmap,
 #ifdef CONFIG_DEBUG_FS
 	.debugfs_init       = msm_debugfs_init,
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_drv.h
@@ -157,7 +157,7 @@
 
 	/* when we have more than one 'msm_gpu' these need to be an array: */
 	struct msm_gpu *gpu;
-	struct msm_file_private *lastctx;
+
 	/* gpu is only set on open(), but we need this info earlier */
 	bool is_a2xx;
 	bool has_cached_coherent;
@@ -247,8 +247,6 @@
 
 struct msm_pending_timer;
 
-int msm_atomic_prepare_fb(struct drm_plane *plane,
-			  struct drm_plane_state *new_state);
 int msm_atomic_init_pending_timer(struct msm_pending_timer *timer,
 		struct msm_kms *kms, int crtc_idx);
 void msm_atomic_destroy_pending_timer(struct msm_pending_timer *timer);
@@ -298,6 +296,7 @@
 void msm_gem_shrinker_init(struct drm_device *dev);
 void msm_gem_shrinker_cleanup(struct drm_device *dev);
 
+int msm_gem_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma);
 struct sg_table *msm_gem_prime_get_sg_table(struct drm_gem_object *obj);
 int msm_gem_prime_vmap(struct drm_gem_object *obj, struct dma_buf_map *map);
 void msm_gem_prime_vunmap(struct drm_gem_object *obj, struct dma_buf_map *map);
@@ -307,9 +306,9 @@
 void msm_gem_prime_unpin(struct drm_gem_object *obj);
 
 int msm_framebuffer_prepare(struct drm_framebuffer *fb,
-		struct msm_gem_address_space *aspace);
+		struct msm_gem_address_space *aspace, bool needs_dirtyfb);
 void msm_framebuffer_cleanup(struct drm_framebuffer *fb,
-		struct msm_gem_address_space *aspace);
+		struct msm_gem_address_space *aspace, bool needed_dirtyfb);
 uint32_t msm_framebuffer_iova(struct drm_framebuffer *fb,
 		struct msm_gem_address_space *aspace, int plane);
 struct drm_gem_object *msm_framebuffer_bo(struct drm_framebuffer *fb, int plane);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_fb.c
@@ -18,16 +18,36 @@
 struct msm_framebuffer {
 	struct drm_framebuffer base;
 	const struct msm_format *format;
+
+	/* Count of # of attached planes which need dirtyfb: */
+	refcount_t dirtyfb;
 };
 #define to_msm_framebuffer(x) container_of(x, struct msm_framebuffer, base)
 
 static struct drm_framebuffer *msm_framebuffer_init(struct drm_device *dev,
 		const struct drm_mode_fb_cmd2 *mode_cmd, struct drm_gem_object **bos);
 
+static int msm_framebuffer_dirtyfb(struct drm_framebuffer *fb,
+				   struct drm_file *file_priv, unsigned int flags,
+				   unsigned int color, struct drm_clip_rect *clips,
+				   unsigned int num_clips)
+{
+	struct msm_framebuffer *msm_fb = to_msm_framebuffer(fb);
+
+	/* If this fb is not used on any display requiring pixel data to be
+	 * flushed, then skip dirtyfb
+	 */
+	if (refcount_read(&msm_fb->dirtyfb) == 1)
+		return 0;
+
+	return drm_atomic_helper_dirtyfb(fb, file_priv, flags, color,
+					 clips, num_clips);
+}
+
 static const struct drm_framebuffer_funcs msm_framebuffer_funcs = {
 	.create_handle = drm_gem_fb_create_handle,
 	.destroy = drm_gem_fb_destroy,
-	.dirty = drm_atomic_helper_dirtyfb,
+	.dirty = msm_framebuffer_dirtyfb,
 };
 
 #ifdef CONFIG_DEBUG_FS
@@ -48,17 +68,19 @@
 }
 #endif
 
-/* prepare/pin all the fb's bo's for scanout.  Note that it is not valid
- * to prepare an fb more multiple different initiator 'id's.  But that
- * should be fine, since only the scanout (mdpN) side of things needs
- * this, the gpu doesn't care about fb's.
+/* prepare/pin all the fb's bo's for scanout.
  */
 int msm_framebuffer_prepare(struct drm_framebuffer *fb,
-		struct msm_gem_address_space *aspace)
+		struct msm_gem_address_space *aspace,
+		bool needs_dirtyfb)
 {
+	struct msm_framebuffer *msm_fb = to_msm_framebuffer(fb);
 	int ret, i, n = fb->format->num_planes;
 	uint64_t iova;
 
+	if (needs_dirtyfb)
+		refcount_inc(&msm_fb->dirtyfb);
+
 	for (i = 0; i < n; i++) {
 		ret = msm_gem_get_and_pin_iova(fb->obj[i], aspace, &iova);
 		drm_dbg_state(fb->dev, "FB[%u]: iova[%d]: %08llx (%d)", fb->base.id, i, iova, ret);
@@ -70,10 +92,15 @@
 }
 
 void msm_framebuffer_cleanup(struct drm_framebuffer *fb,
-		struct msm_gem_address_space *aspace)
+		struct msm_gem_address_space *aspace,
+		bool needed_dirtyfb)
 {
+	struct msm_framebuffer *msm_fb = to_msm_framebuffer(fb);
 	int i, n = fb->format->num_planes;
 
+	if (needed_dirtyfb)
+		refcount_dec(&msm_fb->dirtyfb);
+
 	for (i = 0; i < n; i++)
 		msm_gem_unpin_iova(fb->obj[i], aspace);
 }
@@ -194,6 +221,8 @@
 		goto fail;
 	}
 
+	refcount_set(&msm_fb->dirtyfb, 1);
+
 	drm_dbg_state(dev, "create: FB ID: %d (%p)", fb->base.id, fb);
 
 	return fb;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_fence.c
@@ -21,7 +21,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	fctx->dev = dev;
-	strncpy(fctx->name, name, sizeof(fctx->name));
+	strscpy(fctx->name, name, sizeof(fctx->name));
 	fctx->context = dma_fence_context_alloc(1);
 	fctx->fenceptr = fenceptr;
 	spin_lock_init(&fctx->spinlock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_gem.c
@@ -937,6 +937,7 @@
 					get_pid_task(aspace->pid, PIDTYPE_PID);
 				if (task) {
 					comm = kstrdup(task->comm, GFP_KERNEL);
+					put_task_struct(task);
 				} else {
 					comm = NULL;
 				}
@@ -1055,8 +1056,7 @@
 {
 	struct msm_gem_object *msm_obj = to_msm_bo(obj);
 
-	vma->vm_flags &= ~VM_PFNMAP;
-	vma->vm_flags |= VM_MIXEDMAP | VM_DONTEXPAND;
+	vma->vm_flags |= VM_IO | VM_MIXEDMAP | VM_DONTEXPAND | VM_DONTDUMP;
 	vma->vm_page_prot = msm_gem_pgprot(msm_obj, vm_get_page_prot(vma->vm_flags));
 
 	return 0;
@@ -1132,6 +1132,7 @@
 	msm_obj->flags = flags;
 	msm_obj->madv = MSM_MADV_WILLNEED;
 
+	INIT_LIST_HEAD(&msm_obj->node);
 	INIT_LIST_HEAD(&msm_obj->vmas);
 
 	*obj = &msm_obj->base;
@@ -1166,7 +1167,7 @@
 
 	ret = msm_gem_new_impl(dev, size, flags, &obj);
 	if (ret)
-		goto fail;
+		return ERR_PTR(ret);
 
 	msm_obj = to_msm_bo(obj);
 
@@ -1250,7 +1251,7 @@
 
 	ret = msm_gem_new_impl(dev, size, MSM_BO_WC, &obj);
 	if (ret)
-		goto fail;
+		return ERR_PTR(ret);
 
 	drm_gem_private_object_init(dev, obj, size);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_gem_prime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_gem_prime.c
@@ -11,13 +11,28 @@
 #include "msm_drv.h"
 #include "msm_gem.h"
 
+int msm_gem_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
+{
+	int ret;
+
+	/* Ensure the mmap offset is initialized.  We lazily initialize it,
+	 * so if it has not been first mmap'd directly as a GEM object, the
+	 * mmap offset will not be already initialized.
+	 */
+	ret = drm_gem_create_mmap_offset(obj);
+	if (ret)
+		return ret;
+
+	return drm_gem_prime_mmap(obj, vma);
+}
+
 struct sg_table *msm_gem_prime_get_sg_table(struct drm_gem_object *obj)
 {
 	struct msm_gem_object *msm_obj = to_msm_bo(obj);
 	int npages = obj->size >> PAGE_SHIFT;
 
 	if (WARN_ON(!msm_obj->pages))  /* should have already pinned! */
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	return drm_prime_pages_to_sg(obj->dev, msm_obj->pages, npages);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_gem_submit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_gem_submit.c
@@ -220,6 +220,10 @@
 			goto out;
 		}
 		submit->cmd[i].relocs = kmalloc(sz, GFP_KERNEL);
+		if (!submit->cmd[i].relocs) {
+			ret = -ENOMEM;
+			goto out;
+		}
 		ret = copy_from_user(submit->cmd[i].relocs, userptr, sz);
 		if (ret) {
 			ret = -EFAULT;
@@ -636,8 +640,8 @@
 	int ret = 0;
 	uint32_t i, j;
 
-	post_deps = kmalloc_array(nr_syncobjs, sizeof(*post_deps),
-	                          GFP_KERNEL | __GFP_NOWARN | __GFP_NORETRY);
+	post_deps = kcalloc(nr_syncobjs, sizeof(*post_deps),
+			    GFP_KERNEL | __GFP_NOWARN | __GFP_NORETRY);
 	if (!post_deps)
 		return ERR_PTR(-ENOMEM);
 
@@ -652,7 +656,6 @@
 		}
 
 		post_deps[i].point = syncobj_desc.point;
-		post_deps[i].chain = NULL;
 
 		if (syncobj_desc.flags) {
 			ret = -EINVAL;
@@ -780,6 +783,7 @@
 		args->nr_cmds);
 	if (IS_ERR(submit)) {
 		ret = PTR_ERR(submit);
+		submit = NULL;
 		goto out_unlock;
 	}
 
@@ -886,9 +890,9 @@
 	 * to the underlying fence.
 	 */
 	submit->fence_id = idr_alloc_cyclic(&queue->fence_idr,
-			submit->user_fence, 0, INT_MAX, GFP_KERNEL);
+			submit->user_fence, 1, INT_MAX, GFP_KERNEL);
 	if (submit->fence_id < 0) {
-		ret = submit->fence_id = 0;
+		ret = submit->fence_id;
 		submit->fence_id = 0;
 		goto out;
 	}
@@ -911,6 +915,7 @@
 	drm_sched_entity_push_job(&submit->base, queue->entity);
 
 	args->fence = submit->fence_id;
+	queue->last_fence = submit->fence_id;
 
 	msm_reset_syncobjs(syncobjs_to_reset, args->nr_in_syncobjs);
 	msm_process_post_deps(post_deps, args->nr_out_syncobjs,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_gpu.c
@@ -150,7 +150,7 @@
 {
 	int ret;
 
-	WARN_ON(!mutex_is_locked(&gpu->dev->struct_mutex));
+	WARN_ON(!mutex_is_locked(&gpu->lock));
 
 	if (!gpu->needs_hw_init)
 		return 0;
@@ -296,7 +296,7 @@
 		state->bos = kcalloc(nr,
 			sizeof(struct msm_gpu_state_bo), GFP_KERNEL);
 
-		for (i = 0; i < submit->nr_bos; i++) {
+		for (i = 0; state->bos && i < submit->nr_bos; i++) {
 			if (should_dump(submit, i)) {
 				msm_gpu_crashstate_get_bo(state, submit->bos[i].obj,
 					submit->bos[i].iova, submit->bos[i].flags);
@@ -361,7 +361,7 @@
 	char *comm = NULL, *cmd = NULL;
 	int i;
 
-	mutex_lock(&dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 
 	DRM_DEV_ERROR(dev->dev, "%s: hangcheck recover!\n", gpu->name);
 
@@ -442,7 +442,7 @@
 		}
 	}
 
-	mutex_unlock(&dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	msm_gpu_retire(gpu);
 }
@@ -450,12 +450,11 @@
 static void fault_worker(struct kthread_work *work)
 {
 	struct msm_gpu *gpu = container_of(work, struct msm_gpu, fault_work);
-	struct drm_device *dev = gpu->dev;
 	struct msm_gem_submit *submit;
 	struct msm_ringbuffer *cur_ring = gpu->funcs->active_ring(gpu);
 	char *comm = NULL, *cmd = NULL;
 
-	mutex_lock(&dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 
 	submit = find_submit(cur_ring, cur_ring->memptrs->fence + 1);
 	if (submit && submit->fault_dumped)
@@ -490,7 +489,7 @@
 	memset(&gpu->fault_info, 0, sizeof(gpu->fault_info));
 	gpu->aspace->mmu->funcs->resume_translation(gpu->aspace->mmu);
 
-	mutex_unlock(&dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 }
 
 static void hangcheck_timer_reset(struct msm_gpu *gpu)
@@ -658,7 +657,6 @@
 	msm_submit_retire(submit);
 
 	pm_runtime_mark_last_busy(&gpu->pdev->dev);
-	pm_runtime_put_autosuspend(&gpu->pdev->dev);
 
 	spin_lock_irqsave(&ring->submit_lock, flags);
 	list_del(&submit->node);
@@ -672,6 +670,8 @@
 		msm_devfreq_idle(gpu);
 	mutex_unlock(&gpu->active_lock);
 
+	pm_runtime_put_autosuspend(&gpu->pdev->dev);
+
 	msm_gem_submit_put(submit);
 }
 
@@ -733,7 +733,7 @@
 	struct msm_ringbuffer *ring = submit->ring;
 	unsigned long flags;
 
-	WARN_ON(!mutex_is_locked(&dev->struct_mutex));
+	WARN_ON(!mutex_is_locked(&gpu->lock));
 
 	pm_runtime_get_sync(&gpu->pdev->dev);
 
@@ -763,7 +763,7 @@
 	mutex_unlock(&gpu->active_lock);
 
 	gpu->funcs->submit(gpu, submit);
-	priv->lastctx = submit->queue->ctx;
+	gpu->cur_ctx_seqno = submit->queue->ctx->seqno;
 
 	hangcheck_timer_reset(gpu);
 }
@@ -848,6 +848,7 @@
 
 	INIT_LIST_HEAD(&gpu->active_list);
 	mutex_init(&gpu->active_lock);
+	mutex_init(&gpu->lock);
 	kthread_init_work(&gpu->retire_work, retire_worker);
 	kthread_init_work(&gpu->recover_work, recover_worker);
 	kthread_init_work(&gpu->fault_work, fault_worker);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_gpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_gpu.h
@@ -137,6 +137,17 @@
 	struct msm_ringbuffer *rb[MSM_GPU_MAX_RINGS];
 	int nr_rings;
 
+	/**
+	 * cur_ctx_seqno:
+	 *
+	 * The ctx->seqno value of the last context to submit rendering,
+	 * and the one with current pgtables installed (for generations
+	 * that support per-context pgtables).  Tracked by seqno rather
+	 * than pointer value to avoid dangling pointers, and cases where
+	 * a ctx can be freed and a new one created with the same address.
+	 */
+	int cur_ctx_seqno;
+
 	/*
 	 * List of GEM active objects on this gpu.  Protected by
 	 * msm_drm_private::mm_lock
@@ -144,12 +155,22 @@
 	struct list_head active_list;
 
 	/**
+	 * lock:
+	 *
+	 * General lock for serializing all the gpu things.
+	 *
+	 * TODO move to per-ring locking where feasible (ie. submit/retire
+	 * path, etc)
+	 */
+	struct mutex lock;
+
+	/**
 	 * active_submits:
 	 *
 	 * The number of submitted but not yet retired submits, used to
 	 * determine transitions between active and idle.
 	 *
-	 * Protected by lock
+	 * Protected by active_lock
 	 */
 	int active_submits;
 
@@ -352,6 +373,8 @@
  * @ring_nr:   the ringbuffer used by this submitqueue, which is determined
  *             by the submitqueue's priority
  * @faults:    the number of GPU hangs associated with this submitqueue
+ * @last_fence: the sequence number of the last allocated fence (for error
+ *             checking)
  * @ctx:       the per-drm_file context associated with the submitqueue (ie.
  *             which set of pgtables do submits jobs associated with the
  *             submitqueue use)
@@ -367,6 +390,7 @@
 	u32 flags;
 	u32 ring_nr;
 	int faults;
+	uint32_t last_fence;
 	struct msm_file_private *ctx;
 	struct list_head node;
 	struct idr fence_idr;
@@ -527,28 +551,28 @@
 {
 	struct msm_gpu_state *state = NULL;
 
-	mutex_lock(&gpu->dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 
 	if (gpu->crashstate) {
 		kref_get(&gpu->crashstate->ref);
 		state = gpu->crashstate;
 	}
 
-	mutex_unlock(&gpu->dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	return state;
 }
 
 static inline void msm_gpu_crashstate_put(struct msm_gpu *gpu)
 {
-	mutex_lock(&gpu->dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 
 	if (gpu->crashstate) {
 		if (gpu->funcs->gpu_state_put(gpu->crashstate))
 			gpu->crashstate = NULL;
 	}
 
-	mutex_unlock(&gpu->dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_gpu_devfreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_gpu_devfreq.c
@@ -20,6 +20,10 @@
 	struct msm_gpu *gpu = dev_to_gpu(dev);
 	struct dev_pm_opp *opp;
 
+	/*
+	 * Note that devfreq_recommended_opp() can modify the freq
+	 * to something that actually is in the opp table:
+	 */
 	opp = devfreq_recommended_opp(dev, freq, flags);
 
 	/*
@@ -28,6 +32,7 @@
 	 */
 	if (gpu->devfreq.idle_freq) {
 		gpu->devfreq.idle_freq = *freq;
+		dev_pm_opp_put(opp);
 		return 0;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_iommu.c
@@ -58,7 +58,7 @@
 	u64 addr = iova;
 	unsigned int i;
 
-	for_each_sg(sgt->sgl, sg, sgt->nents, i) {
+	for_each_sgtable_sg(sgt, sg, i) {
 		size_t size = sg->length;
 		phys_addr_t phys = sg_phys(sg);
 
@@ -157,7 +157,12 @@
 	/* Get the pagetable configuration from the domain */
 	if (adreno_smmu->cookie)
 		ttbr1_cfg = adreno_smmu->get_ttbr1_cfg(adreno_smmu->cookie);
-	if (!ttbr1_cfg)
+
+	/*
+	 * If you hit this WARN_ONCE() you are probably missing an entry in
+	 * qcom_smmu_impl_of_match[] in arm-smmu-qcom.c
+	 */
+	if (WARN_ONCE(!ttbr1_cfg, "No per-process page tables"))
 		return ERR_PTR(-ENODEV);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_kms.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_kms.h
@@ -149,6 +149,7 @@
 
 	/* irq number to be passed on to msm_irq_install */
 	int irq;
+	bool irq_requested;
 
 	/* mapper-id used to request GEM buffer mapped for scanout: */
 	struct msm_gem_address_space *aspace;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_perf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_perf.c
@@ -155,9 +155,12 @@
 	struct msm_gpu *gpu = priv->gpu;
 	int ret = 0;
 
-	mutex_lock(&dev->struct_mutex);
+	if (!gpu)
+		return -ENODEV;
 
-	if (perf->open || !gpu) {
+	mutex_lock(&gpu->lock);
+
+	if (perf->open) {
 		ret = -EBUSY;
 		goto out;
 	}
@@ -171,7 +174,7 @@
 	perf->next_jiffies = jiffies + SAMPLE_TIME;
 
 out:
-	mutex_unlock(&dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_rd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_rd.c
@@ -86,7 +86,7 @@
 	struct msm_gem_submit *submit;
 
 	/* fifo access is synchronized on the producer side by
-	 * struct_mutex held by submit code (otherwise we could
+	 * gpu->lock held by submit code (otherwise we could
 	 * end up w/ cmds logged in different order than they
 	 * were executed).  And read_lock synchronizes the reads
 	 */
@@ -181,9 +181,12 @@
 	uint32_t gpu_id;
 	int ret = 0;
 
-	mutex_lock(&dev->struct_mutex);
+	if (!gpu)
+		return -ENODEV;
 
-	if (rd->open || !gpu) {
+	mutex_lock(&gpu->lock);
+
+	if (rd->open) {
 		ret = -EBUSY;
 		goto out;
 	}
@@ -191,6 +194,9 @@
 	file->private_data = rd;
 	rd->open = true;
 
+	/* Reset fifo to clear any previously unread data: */
+	rd->fifo.head = rd->fifo.tail = 0;
+
 	/* the parsing tools need to know gpu-id to know which
 	 * register database to load.
 	 */
@@ -200,7 +206,7 @@
 	rd_write_section(rd, RD_GPU_ID, &gpu_id, sizeof(gpu_id));
 
 out:
-	mutex_unlock(&dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 	return ret;
 }
 
@@ -340,11 +346,10 @@
 	msm_gem_unlock(&obj->base);
 }
 
-/* called under struct_mutex */
+/* called under gpu->lock */
 void msm_rd_dump_submit(struct msm_rd_state *rd, struct msm_gem_submit *submit,
 		const char *fmt, ...)
 {
-	struct drm_device *dev = submit->dev;
 	struct task_struct *task;
 	char msg[256];
 	int i, n;
@@ -355,7 +360,7 @@
 	/* writing into fifo is serialized by caller, and
 	 * rd->read_lock is used to serialize the reads
 	 */
-	WARN_ON(!mutex_is_locked(&dev->struct_mutex));
+	WARN_ON(!mutex_is_locked(&submit->gpu->lock));
 
 	if (fmt) {
 		va_list args;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_ringbuffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_ringbuffer.c
@@ -32,11 +32,11 @@
 	pm_runtime_get_sync(&gpu->pdev->dev);
 
 	/* TODO move submit path over to using a per-ring lock.. */
-	mutex_lock(&gpu->dev->struct_mutex);
+	mutex_lock(&gpu->lock);
 
 	msm_gpu_submit(gpu, submit);
 
-	mutex_unlock(&gpu->dev->struct_mutex);
+	mutex_unlock(&gpu->lock);
 
 	pm_runtime_put(&gpu->pdev->dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/msm/msm_submitqueue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/msm/msm_submitqueue.c
@@ -101,6 +101,7 @@
 
 		ret = drm_sched_entity_init(entity, sched_prio, &sched, 1, NULL);
 		if (ret) {
+			mutex_unlock(&entity_lock);
 			kfree(entity);
 			return ERR_PTR(ret);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mxsfb/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mxsfb/Kconfig
@@ -8,6 +8,7 @@
 	tristate "i.MX (e)LCDIF LCD controller"
 	depends on DRM && OF
 	depends on COMMON_CLK
+	depends on ARCH_MXS || ARCH_MXC || COMPILE_TEST
 	select DRM_MXS
 	select DRM_KMS_HELPER
 	select DRM_KMS_CMA_HELPER
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/mxsfb/mxsfb_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/mxsfb/mxsfb_kms.c
@@ -361,7 +361,17 @@
 		bridge_state =
 			drm_atomic_get_new_bridge_state(state,
 							mxsfb->bridge);
-		bus_format = bridge_state->input_bus_cfg.format;
+		if (!bridge_state)
+			bus_format = MEDIA_BUS_FMT_FIXED;
+		else
+			bus_format = bridge_state->input_bus_cfg.format;
+
+		if (bus_format == MEDIA_BUS_FMT_FIXED) {
+			dev_warn_once(drm->dev,
+				      "Bridge does not provide bus format, assuming MEDIA_BUS_FMT_RGB888_1X24.\n"
+				      "Please fix bridge driver by handling atomic_get_input_bus_fmts.\n");
+			bus_format = MEDIA_BUS_FMT_RGB888_1X24;
+		}
 	}
 
 	/* If there is no bridge, use bus format from connector */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv04/disp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv04/disp.c
@@ -205,7 +205,7 @@
 	nvif_notify_dtor(&disp->flip);
 
 	nouveau_display(dev)->priv = NULL;
-	kfree(disp);
+	vfree(disp);
 
 	nvif_object_unmap(&drm->client.device.object);
 }
@@ -223,7 +223,7 @@
 	struct nv04_display *disp;
 	int i, ret;
 
-	disp = kzalloc(sizeof(*disp), GFP_KERNEL);
+	disp = vzalloc(sizeof(*disp));
 	if (!disp)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv04/tvnv17.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv04/tvnv17.c
@@ -208,6 +208,8 @@
 		struct drm_display_mode *mode;
 
 		mode = drm_mode_duplicate(encoder->dev, tv_mode);
+		if (!mode)
+			continue;
 
 		mode->clock = tv_norm->tv_enc_mode.vrefresh *
 			mode->htotal / 1000 *
@@ -257,6 +259,8 @@
 		if (modes[i].hdisplay == output_mode->hdisplay &&
 		    modes[i].vdisplay == output_mode->vdisplay) {
 			mode = drm_mode_duplicate(encoder->dev, output_mode);
+			if (!mode)
+				continue;
 			mode->type |= DRM_MODE_TYPE_PREFERRED;
 
 		} else {
@@ -264,6 +268,8 @@
 					    modes[i].vdisplay, 60, false,
 					    (output_mode->flags &
 					     DRM_MODE_FLAG_INTERLACE), false);
+			if (!mode)
+				continue;
 		}
 
 		/* CVT modes are sometimes unsuitable... */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv50/atom.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv50/atom.h
@@ -160,14 +160,14 @@
 static inline struct drm_encoder *
 nv50_head_atom_get_encoder(struct nv50_head_atom *atom)
 {
-	struct drm_encoder *encoder = NULL;
+	struct drm_encoder *encoder;
 
 	/* We only ever have a single encoder */
 	drm_for_each_encoder_mask(encoder, atom->state.crtc->dev,
 				  atom->state.encoder_mask)
-		break;
+		return encoder;
 
-	return encoder;
+	return NULL;
 }
 
 #define nv50_wndw_atom(p) container_of((p), struct nv50_wndw_atom, state)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv50/crc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv50/crc.c
@@ -411,9 +411,18 @@
 		struct nv50_head_atom *armh = nv50_head_atom(old_crtc_state);
 		struct nv50_head_atom *asyh = nv50_head_atom(new_crtc_state);
 		struct nv50_outp_atom *outp_atom;
-		struct nouveau_encoder *outp =
-			nv50_real_outp(nv50_head_atom_get_encoder(armh));
-		struct drm_encoder *encoder = &outp->base.base;
+		struct nouveau_encoder *outp;
+		struct drm_encoder *encoder, *enc;
+
+		enc = nv50_head_atom_get_encoder(armh);
+		if (!enc)
+			continue;
+
+		outp = nv50_real_outp(enc);
+		if (!outp)
+			continue;
+
+		encoder = &outp->base.base;
 
 		if (!asyh->clr.crc)
 			continue;
@@ -464,8 +473,16 @@
 	struct drm_device *dev = crtc->dev;
 	struct nv50_crc *crc = &head->crc;
 	const struct nv50_crc_func *func = nv50_disp(dev)->core->func->crc;
-	struct nouveau_encoder *outp =
-		nv50_real_outp(nv50_head_atom_get_encoder(asyh));
+	struct nouveau_encoder *outp;
+	struct drm_encoder *encoder;
+
+	encoder = nv50_head_atom_get_encoder(asyh);
+	if (!encoder)
+		return;
+
+	outp = nv50_real_outp(encoder);
+	if (!outp)
+		return;
 
 	func->set_src(head, outp->or,
 		      nv50_crc_source_type(outp, asyh->crc.src),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv50/disp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv50/disp.c
@@ -411,6 +411,35 @@
 	return 0;
 }
 
+static void
+nv50_outp_atomic_fix_depth(struct drm_encoder *encoder, struct drm_crtc_state *crtc_state)
+{
+	struct nv50_head_atom *asyh = nv50_head_atom(crtc_state);
+	struct nouveau_encoder *nv_encoder = nouveau_encoder(encoder);
+	struct drm_display_mode *mode = &asyh->state.adjusted_mode;
+	unsigned int max_rate, mode_rate;
+
+	switch (nv_encoder->dcb->type) {
+	case DCB_OUTPUT_DP:
+		max_rate = nv_encoder->dp.link_nr * nv_encoder->dp.link_bw;
+
+		/* we don't support more than 10 anyway */
+		asyh->or.bpc = min_t(u8, asyh->or.bpc, 10);
+
+		/* reduce the bpc until it works out */
+		while (asyh->or.bpc > 6) {
+			mode_rate = DIV_ROUND_UP(mode->clock * asyh->or.bpc * 3, 8);
+			if (mode_rate <= max_rate)
+				break;
+
+			asyh->or.bpc -= 2;
+		}
+		break;
+	default:
+		break;
+	}
+}
+
 static int
 nv50_outp_atomic_check(struct drm_encoder *encoder,
 		       struct drm_crtc_state *crtc_state,
@@ -429,6 +458,9 @@
 	if (crtc_state->mode_changed || crtc_state->connectors_changed)
 		asyh->or.bpc = connector->display_info.bpc;
 
+	/* We might have to reduce the bpc */
+	nv50_outp_atomic_fix_depth(encoder, crtc_state);
+
 	return 0;
 }
 
@@ -2622,14 +2654,6 @@
 {
 	struct nouveau_drm *drm = nouveau_drm(dev);
 	struct drm_encoder *encoder;
-	struct drm_plane *plane;
-
-	drm_for_each_plane(plane, dev) {
-		struct nv50_wndw *wndw = nv50_wndw(plane);
-		if (plane->funcs != &nv50_wndw)
-			continue;
-		nv50_wndw_fini(wndw);
-	}
 
 	list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
 		if (encoder->encoder_type != DRM_MODE_ENCODER_DPMST)
@@ -2645,7 +2669,6 @@
 {
 	struct nv50_core *core = nv50_disp(dev)->core;
 	struct drm_encoder *encoder;
-	struct drm_plane *plane;
 
 	if (resume || runtime)
 		core->func->init(core);
@@ -2658,13 +2681,6 @@
 		}
 	}
 
-	drm_for_each_plane(plane, dev) {
-		struct nv50_wndw *wndw = nv50_wndw(plane);
-		if (plane->funcs != &nv50_wndw)
-			continue;
-		nv50_wndw_init(wndw);
-	}
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv50/wndw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv50/wndw.c
@@ -694,18 +694,6 @@
 	return NVIF_NOTIFY_KEEP;
 }
 
-void
-nv50_wndw_fini(struct nv50_wndw *wndw)
-{
-	nvif_notify_put(&wndw->notify);
-}
-
-void
-nv50_wndw_init(struct nv50_wndw *wndw)
-{
-	nvif_notify_get(&wndw->notify);
-}
-
 static const u64 nv50_cursor_format_modifiers[] = {
 	DRM_FORMAT_MOD_LINEAR,
 	DRM_FORMAT_MOD_INVALID,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/dispnv50/wndw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/dispnv50/wndw.h
@@ -38,10 +38,9 @@
 
 int nv50_wndw_new_(const struct nv50_wndw_func *, struct drm_device *,
 		   enum drm_plane_type, const char *name, int index,
-		   const u32 *format, enum nv50_disp_interlock_type,
-		   u32 interlock_data, u32 heads, struct nv50_wndw **);
-void nv50_wndw_init(struct nv50_wndw *);
-void nv50_wndw_fini(struct nv50_wndw *);
+		   const u32 *format, u32 heads,
+		   enum nv50_disp_interlock_type, u32 interlock_data,
+		   struct nv50_wndw **);
 void nv50_wndw_flush_set(struct nv50_wndw *, u32 *interlock,
 			 struct nv50_wndw_atom *);
 void nv50_wndw_flush_clr(struct nv50_wndw *, u32 *interlock, bool flush,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/include/nvkm/core/subdev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/include/nvkm/core/subdev.h
@@ -62,4 +62,6 @@
 #define nvkm_debug(s,f,a...) nvkm_printk((s), DEBUG,   info, f, ##a)
 #define nvkm_trace(s,f,a...) nvkm_printk((s), TRACE,   info, f, ##a)
 #define nvkm_spam(s,f,a...)  nvkm_printk((s),  SPAM,    dbg, f, ##a)
+
+#define nvkm_error_ratelimited(s,f,a...) nvkm_printk((s), ERROR, err_ratelimited, f, ##a)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_acpi.c
@@ -220,6 +220,9 @@
 	int optimus_funcs;
 	struct pci_dev *parent_pdev;
 
+	if (pdev->vendor != PCI_VENDOR_ID_NVIDIA)
+		return;
+
 	*has_pr3 = false;
 	parent_pdev = pci_upstream_bridge(pdev);
 	if (parent_pdev) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_backlight.c
@@ -46,8 +46,9 @@
 nouveau_get_backlight_name(char backlight_name[BL_NAME_SIZE],
 			   struct nouveau_backlight *bl)
 {
-	const int nb = ida_simple_get(&bl_ida, 0, 0, GFP_KERNEL);
-	if (nb < 0 || nb >= 100)
+	const int nb = ida_alloc_max(&bl_ida, 99, GFP_KERNEL);
+
+	if (nb < 0)
 		return false;
 	if (nb > 0)
 		snprintf(backlight_name, BL_NAME_SIZE, "nv_backlight%d", nb);
@@ -101,7 +102,6 @@
 	if (!(nvif_rd32(device, NV40_PMC_BACKLIGHT) & NV40_PMC_BACKLIGHT_MASK))
 		return -ENODEV;
 
-	props->type = BACKLIGHT_RAW;
 	props->max_brightness = 31;
 	*ops = &nv40_bl_ops;
 	return 0;
@@ -294,7 +294,8 @@
 	struct nouveau_drm *drm = nouveau_drm(nv_encoder->base.base.dev);
 	struct nvif_object *device = &drm->client.device.object;
 
-	if (!nvif_rd32(device, NV50_PDISP_SOR_PWM_CTL(ffs(nv_encoder->dcb->or) - 1)))
+	if (!nvif_rd32(device, NV50_PDISP_SOR_PWM_CTL(ffs(nv_encoder->dcb->or) - 1)) ||
+	    nv_conn->base.status != connector_status_connected)
 		return -ENODEV;
 
 	if (nv_conn->type == DCB_CONNECTOR_eDP) {
@@ -339,7 +340,6 @@
 	else
 		*ops = &nva3_bl_ops;
 
-	props->type = BACKLIGHT_RAW;
 	props->max_brightness = 100;
 
 	return 0;
@@ -407,11 +407,12 @@
 		goto fail_alloc;
 	}
 
+	props.type = BACKLIGHT_RAW;
 	bl->dev = backlight_device_register(backlight_name, connector->kdev,
 					    nv_encoder, ops, &props);
 	if (IS_ERR(bl->dev)) {
 		if (bl->id >= 0)
-			ida_simple_remove(&bl_ida, bl->id);
+			ida_free(&bl_ida, bl->id);
 		ret = PTR_ERR(bl->dev);
 		goto fail_alloc;
 	}
@@ -439,7 +440,7 @@
 		return;
 
 	if (bl->id >= 0)
-		ida_simple_remove(&bl_ida, bl->id);
+		ida_free(&bl_ida, bl->id);
 
 	backlight_device_unregister(bl->dev);
 	nv_conn->backlight = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_bios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_bios.c
@@ -23,6 +23,7 @@
  */
 
 #include "nouveau_drv.h"
+#include "nouveau_bios.h"
 #include "nouveau_reg.h"
 #include "dispnv04/hw.h"
 #include "nouveau_encoder.h"
@@ -1675,7 +1676,7 @@
 	 */
 	if (nv_match_device(dev, 0x0201, 0x1462, 0x8851)) {
 		if (*conn == 0xf2005014 && *conf == 0xffffffff) {
-			fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 1, 1, 1);
+			fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 1, 1, DCB_OUTPUT_B);
 			return false;
 		}
 	}
@@ -1761,26 +1762,26 @@
 #ifdef __powerpc__
 	/* Apple iMac G4 NV17 */
 	if (of_machine_is_compatible("PowerMac4,5")) {
-		fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 0, all_heads, 1);
-		fabricate_dcb_output(dcb, DCB_OUTPUT_ANALOG, 1, all_heads, 2);
+		fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS, 0, all_heads, DCB_OUTPUT_B);
+		fabricate_dcb_output(dcb, DCB_OUTPUT_ANALOG, 1, all_heads, DCB_OUTPUT_C);
 		return;
 	}
 #endif
 
 	/* Make up some sane defaults */
 	fabricate_dcb_output(dcb, DCB_OUTPUT_ANALOG,
-			     bios->legacy.i2c_indices.crt, 1, 1);
+			     bios->legacy.i2c_indices.crt, 1, DCB_OUTPUT_B);
 
 	if (nv04_tv_identify(dev, bios->legacy.i2c_indices.tv) >= 0)
 		fabricate_dcb_output(dcb, DCB_OUTPUT_TV,
 				     bios->legacy.i2c_indices.tv,
-				     all_heads, 0);
+				     all_heads, DCB_OUTPUT_A);
 
 	else if (bios->tmds.output0_script_ptr ||
 		 bios->tmds.output1_script_ptr)
 		fabricate_dcb_output(dcb, DCB_OUTPUT_TMDS,
 				     bios->legacy.i2c_indices.panel,
-				     all_heads, 1);
+				     all_heads, DCB_OUTPUT_B);
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_bo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_bo.c
@@ -281,8 +281,10 @@
 			break;
 	}
 
-	if (WARN_ON(pi < 0))
+	if (WARN_ON(pi < 0)) {
+		kfree(nvbo);
 		return ERR_PTR(-EINVAL);
+	}
 
 	/* Disable compression if suitable settings couldn't be found. */
 	if (nvbo->comp && !vmm->page[pi].comp) {
@@ -820,6 +822,15 @@
 		if (ret == 0) {
 			ret = nouveau_fence_new(chan, false, &fence);
 			if (ret == 0) {
+				/* TODO: figure out a better solution here
+				 *
+				 * wait on the fence here explicitly as going through
+				 * ttm_bo_move_accel_cleanup somehow doesn't seem to do it.
+				 *
+				 * Without this the operation can timeout and we'll fallback to a
+				 * software copy, which might take several minutes to finish.
+				 */
+				nouveau_fence_wait(fence, false, false);
 				ret = ttm_bo_move_accel_cleanup(bo,
 								&fence->base,
 								evict, false,
@@ -1175,6 +1186,8 @@
 			drm_vma_node_unmap(&nvbo->bo.base.vma_node,
 					   bdev->dev_mapping);
 			nouveau_ttm_io_mem_free_locked(drm, nvbo->bo.resource);
+			nvbo->bo.resource->bus.offset = 0;
+			nvbo->bo.resource->bus.addr = NULL;
 			goto retry;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_connector.c
@@ -503,7 +503,8 @@
 			connector->interlace_allowed =
 				nv_encoder->caps.dp_interlace;
 		else
-			connector->interlace_allowed = true;
+			connector->interlace_allowed =
+				drm->client.device.info.family < NV_DEVICE_INFO_V0_VOLTA;
 		connector->doublescan_allowed = true;
 	} else
 	if (nv_encoder->dcb->type == DCB_OUTPUT_LVDS ||
@@ -728,7 +729,8 @@
 #endif
 
 	nouveau_connector_set_edid(nv_connector, edid);
-	nouveau_connector_set_encoder(connector, nv_encoder);
+	if (nv_encoder)
+		nouveau_connector_set_encoder(connector, nv_encoder);
 	return status;
 }
 
@@ -752,7 +754,6 @@
 	if (!nv_encoder) {
 		NV_ERROR(drm, "can't find encoder to force %s on!\n",
 			 connector->name);
-		connector->status = connector_status_disconnected;
 		return;
 	}
 
@@ -977,6 +978,9 @@
 		struct drm_display_mode *mode;
 
 		mode = drm_mode_duplicate(dev, nv_connector->native_mode);
+		if (!mode)
+			return 0;
+
 		drm_mode_probed_add(connector, mode);
 		ret = 1;
 	}
@@ -985,7 +989,7 @@
 	 * "native" mode as some VBIOS tables require us to use the
 	 * pixel clock as part of the lookup...
 	 */
-	if (connector->connector_type == DRM_MODE_CONNECTOR_LVDS)
+	if (connector->connector_type == DRM_MODE_CONNECTOR_LVDS && nv_connector->native_mode)
 		nouveau_connector_detect_depth(connector);
 
 	if (nv_encoder->dcb->type == DCB_OUTPUT_TV)
@@ -1361,13 +1365,11 @@
 		snprintf(aux_name, sizeof(aux_name), "sor-%04x-%04x",
 			 dcbe->hasht, dcbe->hashm);
 		nv_connector->aux.name = kstrdup(aux_name, GFP_KERNEL);
-		drm_dp_aux_init(&nv_connector->aux);
-		if (ret) {
-			NV_ERROR(drm, "Failed to init AUX adapter for sor-%04x-%04x: %d\n",
-				 dcbe->hasht, dcbe->hashm, ret);
+		if (!nv_connector->aux.name) {
 			kfree(nv_connector);
-			return ERR_PTR(ret);
+			return ERR_PTR(-ENOMEM);
 		}
+		drm_dp_aux_init(&nv_connector->aux);
 		fallthrough;
 	default:
 		funcs = &nouveau_connector_funcs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_display.c
@@ -518,7 +518,7 @@
 
 	pm_runtime_mark_last_busy(drm->dev->dev);
 noop:
-	pm_runtime_put_sync(drm->dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 }
 
 #ifdef CONFIG_ACPI
@@ -540,7 +540,7 @@
 				 * it's own hotplug events.
 				 */
 				pm_runtime_put_autosuspend(drm->dev->dev);
-			} else if (ret == 0) {
+			} else if (ret == 0 || ret == -EINPROGRESS) {
 				/* We've started resuming the GPU already, so
 				 * it will handle scheduling a full reprobe
 				 * itself
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_dmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_dmem.c
@@ -149,7 +149,7 @@
 	if (!spage || !(args->src[0] & MIGRATE_PFN_MIGRATE))
 		return 0;
 
-	dpage = alloc_page_vma(GFP_HIGHUSER, vmf->vma, vmf->address);
+	dpage = alloc_page_vma(GFP_HIGHUSER | __GFP_ZERO, vmf->vma, vmf->address);
 	if (!dpage)
 		return VM_FAULT_SIGBUS;
 	lock_page(dpage);
@@ -679,7 +679,11 @@
 		goto out_free_dma;
 
 	for (i = 0; i < npages; i += max) {
-		args.end = start + (max << PAGE_SHIFT);
+		if (args.start + (max << PAGE_SHIFT) > end)
+			args.end = end;
+		else
+			args.end = args.start + (max << PAGE_SHIFT);
+
 		ret = migrate_vma_setup(&args);
 		if (ret)
 			goto out_free_pfns;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_dp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_dp.c
@@ -109,12 +109,15 @@
 	u8 *dpcd = nv_encoder->dp.dpcd;
 	int ret = NOUVEAU_DP_NONE;
 
-	/* If we've already read the DPCD on an eDP device, we don't need to
-	 * reread it as it won't change
+	/* eDP ports don't support hotplugging - so there's no point in probing eDP ports unless we
+	 * haven't probed them once before.
 	 */
-	if (connector->connector_type == DRM_MODE_CONNECTOR_eDP &&
-	    dpcd[DP_DPCD_REV] != 0)
-		return NOUVEAU_DP_SST;
+	if (connector->connector_type == DRM_MODE_CONNECTOR_eDP) {
+		if (connector->status == connector_status_connected)
+			return NOUVEAU_DP_SST;
+		else if (connector->status == connector_status_disconnected)
+			return NOUVEAU_DP_NONE;
+	}
 
 	mutex_lock(&nv_encoder->dp.hpd_irq_lock);
 	if (mstm) {
@@ -220,8 +223,6 @@
 }
 
 /* TODO:
- * - Use the minimum possible BPC here, once we add support for the max bpc
- *   property.
  * - Validate against the DP caps advertised by the GPU (we don't check these
  *   yet)
  */
@@ -233,7 +234,11 @@
 {
 	const unsigned int min_clock = 25000;
 	unsigned int max_rate, mode_rate, ds_max_dotclock, clock = mode->clock;
-	const u8 bpp = connector->display_info.bpc * 3;
+	/* Check with the minmum bpc always, so we can advertise better modes.
+	 * In particlar not doing this causes modes to be dropped on HDR
+	 * displays as we might check with a bpc of 16 even.
+	 */
+	const u8 bpp = 6 * 3;
 
 	if (mode->flags & DRM_MODE_FLAG_INTERLACE && !outp->caps.dp_interlace)
 		return MODE_NO_INTERLACE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_drm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_drm.c
@@ -126,10 +126,16 @@
 static inline bool
 nouveau_cli_work_ready(struct dma_fence *fence)
 {
-	if (!dma_fence_is_signaled(fence))
-		return false;
-	dma_fence_put(fence);
-	return true;
+	bool ret = true;
+
+	spin_lock_irq(fence->lock);
+	if (!dma_fence_is_signaled_locked(fence))
+		ret = false;
+	spin_unlock_irq(fence->lock);
+
+	if (ret == true)
+		dma_fence_put(fence);
+	return ret;
 }
 
 static void
@@ -562,6 +568,7 @@
 		nvkm_dbgopt(nouveau_debug, "DRM");
 
 	INIT_LIST_HEAD(&drm->clients);
+	mutex_init(&drm->clients_lock);
 	spin_lock_init(&drm->tile.lock);
 
 	/* workaround an odd issue on nvc1 by disabling the device's
@@ -632,6 +639,7 @@
 static void
 nouveau_drm_device_fini(struct drm_device *dev)
 {
+	struct nouveau_cli *cli, *temp_cli;
 	struct nouveau_drm *drm = nouveau_drm(dev);
 
 	if (nouveau_pmops_runtime()) {
@@ -656,9 +664,28 @@
 	nouveau_ttm_fini(drm);
 	nouveau_vga_fini(drm);
 
+	/*
+	 * There may be existing clients from as-yet unclosed files. For now,
+	 * clean them up here rather than deferring until the file is closed,
+	 * but this likely not correct if we want to support hot-unplugging
+	 * properly.
+	 */
+	mutex_lock(&drm->clients_lock);
+	list_for_each_entry_safe(cli, temp_cli, &drm->clients, head) {
+		list_del(&cli->head);
+		mutex_lock(&cli->mutex);
+		if (cli->abi16)
+			nouveau_abi16_fini(cli->abi16);
+		mutex_unlock(&cli->mutex);
+		nouveau_cli_fini(cli);
+		kfree(cli);
+	}
+	mutex_unlock(&drm->clients_lock);
+
 	nouveau_cli_fini(&drm->client);
 	nouveau_cli_fini(&drm->master);
 	nvif_parent_dtor(&drm->parent);
+	mutex_destroy(&drm->clients_lock);
 	kfree(drm);
 }
 
@@ -796,7 +823,7 @@
 	struct nvkm_client *client;
 	struct nvkm_device *device;
 
-	drm_dev_unregister(dev);
+	drm_dev_unplug(dev);
 
 	client = nvxx_client(&drm->client.base);
 	device = nvkm_device_find(client->device);
@@ -1090,9 +1117,9 @@
 
 	fpriv->driver_priv = cli;
 
-	mutex_lock(&drm->client.mutex);
+	mutex_lock(&drm->clients_lock);
 	list_add(&cli->head, &drm->clients);
-	mutex_unlock(&drm->client.mutex);
+	mutex_unlock(&drm->clients_lock);
 
 done:
 	if (ret && cli) {
@@ -1110,6 +1137,16 @@
 {
 	struct nouveau_cli *cli = nouveau_cli(fpriv);
 	struct nouveau_drm *drm = nouveau_drm(dev);
+	int dev_index;
+
+	/*
+	 * The device is gone, and as it currently stands all clients are
+	 * cleaned up in the removal codepath. In the future this may change
+	 * so that we can support hot-unplugging, but for now we immediately
+	 * return to avoid a double-free situation.
+	 */
+	if (!drm_dev_enter(dev, &dev_index))
+		return;
 
 	pm_runtime_get_sync(dev->dev);
 
@@ -1118,14 +1155,15 @@
 		nouveau_abi16_fini(cli->abi16);
 	mutex_unlock(&cli->mutex);
 
-	mutex_lock(&drm->client.mutex);
+	mutex_lock(&drm->clients_lock);
 	list_del(&cli->head);
-	mutex_unlock(&drm->client.mutex);
+	mutex_unlock(&drm->clients_lock);
 
 	nouveau_cli_fini(cli);
 	kfree(cli);
 	pm_runtime_mark_last_busy(dev->dev);
 	pm_runtime_put_autosuspend(dev->dev);
+	drm_dev_exit(dev_index);
 }
 
 static const struct drm_ioctl_desc
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_drv.h
@@ -139,6 +139,11 @@
 
 	struct list_head clients;
 
+	/**
+	 * @clients_lock: Protects access to the @clients list of &struct nouveau_cli.
+	 */
+	struct mutex clients_lock;
+
 	u8 old_pm_cap;
 
 	struct {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_fbcon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_fbcon.c
@@ -466,7 +466,7 @@
 	if (state == FBINFO_STATE_RUNNING) {
 		nouveau_fbcon_hotplug_resume(drm->fbcon);
 		pm_runtime_mark_last_busy(drm->dev->dev);
-		pm_runtime_put_sync(drm->dev->dev);
+		pm_runtime_put_autosuspend(drm->dev->dev);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_fence.c
@@ -353,15 +353,22 @@
 
 		if (ret)
 			return ret;
-	}
 
-	fobj = dma_resv_shared_list(resv);
-	fence = dma_resv_excl_fence(resv);
+		fobj = NULL;
+	} else {
+		fobj = dma_resv_shared_list(resv);
+	}
 
-	if (fence) {
+	/* Waiting for the exclusive fence first causes performance regressions
+	 * under some circumstances. So manually wait for the shared ones first.
+	 */
+	for (i = 0; i < (fobj ? fobj->shared_count : 0) && !ret; ++i) {
 		struct nouveau_channel *prev = NULL;
 		bool must_wait = true;
 
+		fence = rcu_dereference_protected(fobj->shared[i],
+						dma_resv_held(resv));
+
 		f = nouveau_local_fence(fence, chan->drm);
 		if (f) {
 			rcu_read_lock();
@@ -373,20 +380,13 @@
 
 		if (must_wait)
 			ret = dma_fence_wait(fence, intr);
-
-		return ret;
 	}
 
-	if (!exclusive || !fobj)
-		return ret;
-
-	for (i = 0; i < fobj->shared_count && !ret; ++i) {
+	fence = dma_resv_excl_fence(resv);
+	if (fence) {
 		struct nouveau_channel *prev = NULL;
 		bool must_wait = true;
 
-		fence = rcu_dereference_protected(fobj->shared[i],
-						dma_resv_held(resv));
-
 		f = nouveau_local_fence(fence, chan->drm);
 		if (f) {
 			rcu_read_lock();
@@ -398,6 +398,8 @@
 
 		if (must_wait)
 			ret = dma_fence_wait(fence, intr);
+
+		return ret;
 	}
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_gem.c
@@ -56,7 +56,7 @@
 
 	nouveau_bo_del_io_reserve_lru(bo);
 	prot = vm_get_page_prot(vma->vm_flags);
-	ret = ttm_bo_vm_fault_reserved(vmf, prot, TTM_BO_VM_NUM_PREFAULT, 1);
+	ret = ttm_bo_vm_fault_reserved(vmf, prot, TTM_BO_VM_NUM_PREFAULT);
 	nouveau_bo_add_io_reserve_lru(bo);
 	if (ret == VM_FAULT_RETRY && !(vmf->flags & FAULT_FLAG_RETRY_NOWAIT))
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_mem.c
@@ -162,11 +162,12 @@
 }
 
 void
-nouveau_mem_del(struct ttm_resource *reg)
+nouveau_mem_del(struct ttm_resource_manager *man, struct ttm_resource *reg)
 {
 	struct nouveau_mem *mem = nouveau_mem(reg);
 
 	nouveau_mem_fini(mem);
+	ttm_resource_fini(man, reg);
 	kfree(mem);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_mem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_mem.h
@@ -23,7 +23,8 @@
 
 int nouveau_mem_new(struct nouveau_cli *, u8 kind, u8 comp,
 		    struct ttm_resource **);
-void nouveau_mem_del(struct ttm_resource *);
+void nouveau_mem_del(struct ttm_resource_manager *man,
+		     struct ttm_resource *);
 int nouveau_mem_vram(struct ttm_resource *, bool contig, u8 page);
 int nouveau_mem_host(struct ttm_resource *, struct ttm_tt *);
 void nouveau_mem_fini(struct nouveau_mem *);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_prime.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_prime.c
@@ -63,7 +63,8 @@
 	 * to the caller, instead of a normal nouveau_bo ttm reference. */
 	ret = drm_gem_object_init(dev, &nvbo->bo.base, size);
 	if (ret) {
-		nouveau_bo_ref(NULL, &nvbo);
+		drm_gem_object_release(&nvbo->bo.base);
+		kfree(nvbo);
 		obj = ERR_PTR(-ENOMEM);
 		goto unlock;
 	}
@@ -71,7 +72,6 @@
 	ret = nouveau_bo_init(nvbo, size, align, NOUVEAU_GEM_DOMAIN_GART,
 			      sg, robj);
 	if (ret) {
-		nouveau_bo_ref(NULL, &nvbo);
 		obj = ERR_PTR(ret);
 		goto unlock;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_svm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_svm.c
@@ -162,10 +162,14 @@
 	 */
 
 	mm = get_task_mm(current);
+	if (!mm) {
+		return -EINVAL;
+	}
 	mmap_read_lock(mm);
 
 	if (!cli->svm.svmm) {
 		mmap_read_unlock(mm);
+		mmput(mm);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_ttm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_ttm.c
@@ -36,9 +36,10 @@
 #include <core/tegra.h>
 
 static void
-nouveau_manager_del(struct ttm_resource_manager *man, struct ttm_resource *reg)
+nouveau_manager_del(struct ttm_resource_manager *man,
+		    struct ttm_resource *reg)
 {
-	nouveau_mem_del(reg);
+	nouveau_mem_del(man, reg);
 }
 
 static int
@@ -62,7 +63,7 @@
 
 	ret = nouveau_mem_vram(*res, nvbo->contig, nvbo->page);
 	if (ret) {
-		nouveau_mem_del(*res);
+		nouveau_mem_del(man, *res);
 		return ret;
 	}
 
@@ -118,7 +119,7 @@
 	ret = nvif_vmm_get(&mem->cli->vmm.vmm, PTES, false, 12, 0,
 			   (long)(*res)->num_pages << PAGE_SHIFT, &mem->vma[0]);
 	if (ret) {
-		nouveau_mem_del(*res);
+		nouveau_mem_del(man, *res);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nouveau_vmm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nouveau_vmm.c
@@ -108,6 +108,9 @@
 	} else {
 		ret = nvif_vmm_get(&vmm->vmm, PTES, false, mem->mem.page, 0,
 				   mem->mem.size, &tmp);
+		if (ret)
+			goto done;
+
 		vma->addr = tmp.addr;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nv04_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nv04_fence.c
@@ -39,7 +39,7 @@
 static int
 nv04_fence_emit(struct nouveau_fence *fence)
 {
-	struct nvif_push *push = fence->channel->chan.push;
+	struct nvif_push *push = unrcu_pointer(fence->channel)->chan.push;
 	int ret = PUSH_WAIT(push, 2);
 	if (ret == 0) {
 		PUSH_NVSQ(push, NV_SW, 0x0150, fence->base.seqno);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/ce/gt215.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/ce/gt215.c
@@ -78,6 +78,6 @@
 gt215_ce_new(struct nvkm_device *device, enum nvkm_subdev_type type, int inst,
 	     struct nvkm_engine **pengine)
 {
-	return nvkm_falcon_new_(&gt215_ce, device, type, inst,
+	return nvkm_falcon_new_(&gt215_ce, device, type, -1,
 				(device->chipset != 0xaf), 0x104000, pengine);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/device/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/device/base.c
@@ -2606,6 +2606,27 @@
 };
 
 static const struct nvkm_device_chip
+nv173_chipset = {
+	.name = "GA103",
+	.bar      = { 0x00000001, tu102_bar_new },
+	.bios     = { 0x00000001, nvkm_bios_new },
+	.devinit  = { 0x00000001, ga100_devinit_new },
+	.fb       = { 0x00000001, ga102_fb_new },
+	.gpio     = { 0x00000001, ga102_gpio_new },
+	.i2c      = { 0x00000001, gm200_i2c_new },
+	.imem     = { 0x00000001, nv50_instmem_new },
+	.mc       = { 0x00000001, ga100_mc_new },
+	.mmu      = { 0x00000001, tu102_mmu_new },
+	.pci      = { 0x00000001, gp100_pci_new },
+	.privring = { 0x00000001, gm200_privring_new },
+	.timer    = { 0x00000001, gk20a_timer_new },
+	.top      = { 0x00000001, ga100_top_new },
+	.disp     = { 0x00000001, ga102_disp_new },
+	.dma      = { 0x00000001, gv100_dma_new },
+	.fifo     = { 0x00000001, ga102_fifo_new },
+};
+
+static const struct nvkm_device_chip
 nv174_chipset = {
 	.name = "GA104",
 	.bar      = { 0x00000001, tu102_bar_new },
@@ -2627,6 +2648,27 @@
 };
 
 static const struct nvkm_device_chip
+nv176_chipset = {
+	.name = "GA106",
+	.bar      = { 0x00000001, tu102_bar_new },
+	.bios     = { 0x00000001, nvkm_bios_new },
+	.devinit  = { 0x00000001, ga100_devinit_new },
+	.fb       = { 0x00000001, ga102_fb_new },
+	.gpio     = { 0x00000001, ga102_gpio_new },
+	.i2c      = { 0x00000001, gm200_i2c_new },
+	.imem     = { 0x00000001, nv50_instmem_new },
+	.mc       = { 0x00000001, ga100_mc_new },
+	.mmu      = { 0x00000001, tu102_mmu_new },
+	.pci      = { 0x00000001, gp100_pci_new },
+	.privring = { 0x00000001, gm200_privring_new },
+	.timer    = { 0x00000001, gk20a_timer_new },
+	.top      = { 0x00000001, ga100_top_new },
+	.disp     = { 0x00000001, ga102_disp_new },
+	.dma      = { 0x00000001, gv100_dma_new },
+	.fifo     = { 0x00000001, ga102_fifo_new },
+};
+
+static const struct nvkm_device_chip
 nv177_chipset = {
 	.name = "GA107",
 	.bar      = { 0x00000001, tu102_bar_new },
@@ -3071,7 +3113,9 @@
 		case 0x167: device->chip = &nv167_chipset; break;
 		case 0x168: device->chip = &nv168_chipset; break;
 		case 0x172: device->chip = &nv172_chipset; break;
+		case 0x173: device->chip = &nv173_chipset; break;
 		case 0x174: device->chip = &nv174_chipset; break;
+		case 0x176: device->chip = &nv176_chipset; break;
 		case 0x177: device->chip = &nv177_chipset; break;
 		default:
 			if (nvkm_boolopt(device->cfgopt, "NvEnableUnsupportedChipsets", false)) {
@@ -3147,8 +3191,7 @@
 	WARN_ON(device->chip->ptr.inst & ~((1 << ARRAY_SIZE(device->ptr)) - 1));             \
 	for (j = 0; device->chip->ptr.inst && j < ARRAY_SIZE(device->ptr); j++) {            \
 		if ((device->chip->ptr.inst & BIT(j)) && (subdev_mask & BIT_ULL(type))) {    \
-			int inst = (device->chip->ptr.inst == 1) ? -1 : (j);                 \
-			ret = device->chip->ptr.ctor(device, (type), inst, &device->ptr[j]); \
+			ret = device->chip->ptr.ctor(device, (type), (j), &device->ptr[j]);  \
 			subdev = nvkm_device_subdev(device, (type), (j));                    \
 			if (ret) {                                                           \
 				nvkm_subdev_del(&subdev);                                    \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c
@@ -123,7 +123,7 @@
 
 	mutex_init(&tdev->iommu.mutex);
 
-	if (iommu_present(&platform_bus_type)) {
+	if (device_iommu_mapped(dev)) {
 		tdev->iommu.domain = iommu_domain_alloc(&platform_bus_type);
 		if (!tdev->iommu.domain)
 			goto error;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/disp/hdmigv100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/disp/hdmigv100.c
@@ -62,7 +62,6 @@
 		nvkm_wr32(device, 0x6f0108 + hdmi, vendor_infoframe.header);
 		nvkm_wr32(device, 0x6f010c + hdmi, vendor_infoframe.subpack0_low);
 		nvkm_wr32(device, 0x6f0110 + hdmi, vendor_infoframe.subpack0_high);
-		nvkm_wr32(device, 0x6f0110 + hdmi, 0x00000000);
 		nvkm_wr32(device, 0x6f0114 + hdmi, 0x00000000);
 		nvkm_wr32(device, 0x6f0118 + hdmi, 0x00000000);
 		nvkm_wr32(device, 0x6f011c + hdmi, 0x00000000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.h
@@ -123,6 +123,7 @@
 
 extern const struct gf100_grctx_func gk110_grctx;
 void gk110_grctx_generate_r419eb0(struct gf100_gr *);
+void gk110_grctx_generate_r419f78(struct gf100_gr *);
 
 extern const struct gf100_grctx_func gk110b_grctx;
 extern const struct gf100_grctx_func gk208_grctx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk104.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk104.c
@@ -916,7 +916,9 @@
 gk104_grctx_generate_r419f78(struct gf100_gr *gr)
 {
 	struct nvkm_device *device = gr->base.engine.subdev.device;
-	nvkm_mask(device, 0x419f78, 0x00000001, 0x00000000);
+
+	/* bit 3 set disables loads in fp helper invocations, we need it enabled */
+	nvkm_mask(device, 0x419f78, 0x00000009, 0x00000000);
 }
 
 void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk110.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk110.c
@@ -820,6 +820,15 @@
 	nvkm_mask(device, 0x419eb0, 0x00001000, 0x00001000);
 }
 
+void
+gk110_grctx_generate_r419f78(struct gf100_gr *gr)
+{
+	struct nvkm_device *device = gr->base.engine.subdev.device;
+
+	/* bit 3 set disables loads in fp helper invocations, we need it enabled */
+	nvkm_mask(device, 0x419f78, 0x00000008, 0x00000000);
+}
+
 const struct gf100_grctx_func
 gk110_grctx = {
 	.main  = gf100_grctx_generate_main,
@@ -852,4 +861,5 @@
 	.gpc_tpc_nr = gk104_grctx_generate_gpc_tpc_nr,
 	.r418800 = gk104_grctx_generate_r418800,
 	.r419eb0 = gk110_grctx_generate_r419eb0,
+	.r419f78 = gk110_grctx_generate_r419f78,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk110b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk110b.c
@@ -101,4 +101,5 @@
 	.gpc_tpc_nr = gk104_grctx_generate_gpc_tpc_nr,
 	.r418800 = gk104_grctx_generate_r418800,
 	.r419eb0 = gk110_grctx_generate_r419eb0,
+	.r419f78 = gk110_grctx_generate_r419f78,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk208.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgk208.c
@@ -566,4 +566,5 @@
 	.dist_skip_table = gf117_grctx_generate_dist_skip_table,
 	.gpc_tpc_nr = gk104_grctx_generate_gpc_tpc_nr,
 	.r418800 = gk104_grctx_generate_r418800,
+	.r419f78 = gk110_grctx_generate_r419f78,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgm107.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgm107.c
@@ -991,4 +991,5 @@
 	.r406500 = gm107_grctx_generate_r406500,
 	.gpc_tpc_nr = gk104_grctx_generate_gpc_tpc_nr,
 	.r419e00 = gm107_grctx_generate_r419e00,
+	.r419f78 = gk110_grctx_generate_r419f78,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/falcon/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/falcon/base.c
@@ -117,8 +117,12 @@
 int
 nvkm_falcon_reset(struct nvkm_falcon *falcon)
 {
-	nvkm_falcon_disable(falcon);
-	return nvkm_falcon_enable(falcon);
+	if (!falcon->func->reset) {
+		nvkm_falcon_disable(falcon);
+		return nvkm_falcon_enable(falcon);
+	}
+
+	return falcon->func->reset(falcon);
 }
 
 int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/acr/gm200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/acr/gm200.c
@@ -207,11 +207,13 @@
 gm200_acr_wpr_parse(struct nvkm_acr *acr)
 {
 	const struct wpr_header *hdr = (void *)acr->wpr_fw->data;
+	struct nvkm_acr_lsfw *lsfw;
 
 	while (hdr->falcon_id != WPR_HEADER_V0_FALCON_ID_INVALID) {
 		wpr_header_dump(&acr->subdev, hdr);
-		if (!nvkm_acr_lsfw_add(NULL, acr, NULL, (hdr++)->falcon_id))
-			return -ENOMEM;
+		lsfw = nvkm_acr_lsfw_add(NULL, acr, NULL, (hdr++)->falcon_id);
+		if (IS_ERR(lsfw))
+			return PTR_ERR(lsfw);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/acr/gp102.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/acr/gp102.c
@@ -161,11 +161,13 @@
 gp102_acr_wpr_parse(struct nvkm_acr *acr)
 {
 	const struct wpr_header_v1 *hdr = (void *)acr->wpr_fw->data;
+	struct nvkm_acr_lsfw *lsfw;
 
 	while (hdr->falcon_id != WPR_HEADER_V1_FALCON_ID_INVALID) {
 		wpr_header_v1_dump(&acr->subdev, hdr);
-		if (!nvkm_acr_lsfw_add(NULL, acr, NULL, (hdr++)->falcon_id))
-			return -ENOMEM;
+		lsfw = nvkm_acr_lsfw_add(NULL, acr, NULL, (hdr++)->falcon_id);
+		if (IS_ERR(lsfw))
+			return PTR_ERR(lsfw);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/acr/hsfw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/acr/hsfw.c
@@ -142,11 +142,12 @@
 
 	hsfw->imem_size = desc->code_size;
 	hsfw->imem_tag = desc->start_tag;
-	hsfw->imem = kmalloc(desc->code_size, GFP_KERNEL);
-	memcpy(hsfw->imem, data + desc->code_off, desc->code_size);
-
+	hsfw->imem = kmemdup(data + desc->code_off, desc->code_size, GFP_KERNEL);
 	nvkm_firmware_put(fw);
-	return 0;
+	if (!hsfw->imem)
+		return -ENOMEM;
+	else
+		return 0;
 }
 
 int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/bios/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/bios/base.c
@@ -33,12 +33,12 @@
 {
 	u32 p = *addr;
 
-	if (*addr > bios->image0_size && bios->imaged_addr) {
+	if (*addr >= bios->image0_size && bios->imaged_addr) {
 		*addr -= bios->image0_size;
 		*addr += bios->imaged_addr;
 	}
 
-	if (unlikely(*addr + size >= bios->size)) {
+	if (unlikely(*addr + size > bios->size)) {
 		nvkm_error(&bios->subdev, "OOB %d %08x %08x\n", size, p, *addr);
 		return false;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadow.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadow.c
@@ -154,11 +154,17 @@
 	return (void *)fw;
 }
 
+static void
+shadow_fw_release(void *fw)
+{
+	release_firmware(fw);
+}
+
 static const struct nvbios_source
 shadow_fw = {
 	.name = "firmware",
 	.init = shadow_fw_init,
-	.fini = (void(*)(void *))release_firmware,
+	.fini = shadow_fw_release,
 	.read = shadow_fw_read,
 	.rw = false,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowof.c
@@ -66,11 +66,16 @@
 	return ERR_PTR(-EINVAL);
 }
 
+static void of_fini(void *p)
+{
+	kfree(p);
+}
+
 const struct nvbios_source
 nvbios_of = {
 	.name = "OpenFirmware",
 	.init = of_init,
-	.fini = (void(*)(void *))kfree,
+	.fini = of_fini,
 	.read = of_read,
 	.size = of_size,
 	.rw = false,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/bus/gf100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/bus/gf100.c
@@ -35,13 +35,13 @@
 		u32 addr = nvkm_rd32(device, 0x009084);
 		u32 data = nvkm_rd32(device, 0x009088);
 
-		nvkm_error(subdev,
-			   "MMIO %s of %08x FAULT at %06x [ %s%s%s]\n",
-			   (addr & 0x00000002) ? "write" : "read", data,
-			   (addr & 0x00fffffc),
-			   (stat & 0x00000002) ? "!ENGINE " : "",
-			   (stat & 0x00000004) ? "PRIVRING " : "",
-			   (stat & 0x00000008) ? "TIMEOUT " : "");
+		nvkm_error_ratelimited(subdev,
+				       "MMIO %s of %08x FAULT at %06x [ %s%s%s]\n",
+				       (addr & 0x00000002) ? "write" : "read", data,
+				       (addr & 0x00fffffc),
+				       (stat & 0x00000002) ? "!ENGINE " : "",
+				       (stat & 0x00000004) ? "PRIVRING " : "",
+				       (stat & 0x00000008) ? "TIMEOUT " : "");
 
 		nvkm_wr32(device, 0x009084, 0x00000000);
 		nvkm_wr32(device, 0x001100, (stat & 0x0000000e));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/bus/nv31.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/bus/nv31.c
@@ -45,9 +45,9 @@
 		u32 addr = nvkm_rd32(device, 0x009084);
 		u32 data = nvkm_rd32(device, 0x009088);
 
-		nvkm_error(subdev, "MMIO %s of %08x FAULT at %06x\n",
-			   (addr & 0x00000002) ? "write" : "read", data,
-			   (addr & 0x00fffffc));
+		nvkm_error_ratelimited(subdev, "MMIO %s of %08x FAULT at %06x\n",
+				       (addr & 0x00000002) ? "write" : "read", data,
+				       (addr & 0x00fffffc));
 
 		stat &= ~0x00000008;
 		nvkm_wr32(device, 0x001100, 0x00000008);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/bus/nv50.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/bus/nv50.c
@@ -60,9 +60,9 @@
 		u32 addr = nvkm_rd32(device, 0x009084);
 		u32 data = nvkm_rd32(device, 0x009088);
 
-		nvkm_error(subdev, "MMIO %s of %08x FAULT at %06x\n",
-			   (addr & 0x00000002) ? "write" : "read", data,
-			   (addr & 0x00fffffc));
+		nvkm_error_ratelimited(subdev, "MMIO %s of %08x FAULT at %06x\n",
+				       (addr & 0x00000002) ? "write" : "read", data,
+				       (addr & 0x00fffffc));
 
 		stat &= ~0x00000008;
 		nvkm_wr32(device, 0x001100, 0x00000008);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/clk/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/clk/base.c
@@ -135,10 +135,10 @@
 
 	list_for_each_entry_from_reverse(cstate, &pstate->list, head) {
 		if (nvkm_cstate_valid(clk, cstate, max_volt, clk->temp))
-			break;
+			return cstate;
 	}
 
-	return cstate;
+	return NULL;
 }
 
 static struct nvkm_cstate *
@@ -169,6 +169,8 @@
 	if (!list_empty(&pstate->list)) {
 		cstate = nvkm_cstate_get(clk, pstate, cstatei);
 		cstate = nvkm_cstate_find_best(clk, pstate, cstate);
+		if (!cstate)
+			return -EINVAL;
 	} else {
 		cstate = &pstate->base;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/devinit/tu102.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/devinit/tu102.c
@@ -65,10 +65,33 @@
 	return ret;
 }
 
+static int
+tu102_devinit_wait(struct nvkm_device *device)
+{
+	unsigned timeout = 50 + 2000;
+
+	do {
+		if (nvkm_rd32(device, 0x118128) & 0x00000001) {
+			if ((nvkm_rd32(device, 0x118234) & 0x000000ff) == 0xff)
+				return 0;
+		}
+
+		usleep_range(1000, 2000);
+	} while (timeout--);
+
+	return -ETIMEDOUT;
+}
+
 int
 tu102_devinit_post(struct nvkm_devinit *base, bool post)
 {
 	struct nv50_devinit *init = nv50_devinit(base);
+	int ret;
+
+	ret = tu102_devinit_wait(init->base.subdev.device);
+	if (ret)
+		return ret;
+
 	gm200_devinit_preos(init, post);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c
@@ -221,8 +221,11 @@
 	void __iomem *map = NULL;
 
 	/* Already mapped? */
-	if (refcount_inc_not_zero(&iobj->maps))
+	if (refcount_inc_not_zero(&iobj->maps)) {
+		/* read barrier match the wmb on refcount set */
+		smp_rmb();
 		return iobj->map;
+	}
 
 	/* Take the lock, and re-check that another thread hasn't
 	 * already mapped the object in the meantime.
@@ -249,6 +252,8 @@
 			iobj->base.memory.ptrs = &nv50_instobj_fast;
 		else
 			iobj->base.memory.ptrs = &nv50_instobj_slow;
+		/* barrier to ensure the ptrs are written before refcount is set */
+		smp_wmb();
 		refcount_set(&iobj->maps, 1);
 	}
 
@@ -313,7 +318,7 @@
 	struct nv50_instobj *iobj = nv50_instobj(memory);
 	struct nvkm_instmem *imem = &iobj->imem->base;
 	struct nvkm_vma *bar;
-	void *map = map;
+	void *map;
 
 	mutex_lock(&imem->mutex);
 	if (likely(iobj->lru.next))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/mmu/vmmtu102.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/mmu/vmmtu102.c
@@ -31,7 +31,7 @@
 
 	type |= 0x00000001; /* PAGE_ALL */
 	if (atomic_read(&vmm->engref[NVKM_SUBDEV_BAR]))
-		type |= 0x00000004; /* HUB_ONLY */
+		type |= 0x00000006; /* HUB_ONLY | ALL PDB (hack) */
 
 	mutex_lock(&vmm->mmu->mutex);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/base.c
@@ -94,20 +94,13 @@
 	return 0;
 }
 
-static int
+static void
 nvkm_pmu_reset(struct nvkm_pmu *pmu)
 {
 	struct nvkm_device *device = pmu->subdev.device;
 
 	if (!pmu->func->enabled(pmu))
-		return 0;
-
-	/* Inhibit interrupts, and wait for idle. */
-	nvkm_wr32(device, 0x10a014, 0x0000ffff);
-	nvkm_msec(device, 2000,
-		if (!nvkm_rd32(device, 0x10a04c))
-			break;
-	);
+		return;
 
 	/* Reset. */
 	if (pmu->func->reset)
@@ -118,25 +111,37 @@
 		if (!(nvkm_rd32(device, 0x10a10c) & 0x00000006))
 			break;
 	);
-
-	return 0;
 }
 
 static int
 nvkm_pmu_preinit(struct nvkm_subdev *subdev)
 {
 	struct nvkm_pmu *pmu = nvkm_pmu(subdev);
-	return nvkm_pmu_reset(pmu);
+	nvkm_pmu_reset(pmu);
+	return 0;
 }
 
 static int
 nvkm_pmu_init(struct nvkm_subdev *subdev)
 {
 	struct nvkm_pmu *pmu = nvkm_pmu(subdev);
-	int ret = nvkm_pmu_reset(pmu);
-	if (ret == 0 && pmu->func->init)
-		ret = pmu->func->init(pmu);
-	return ret;
+	struct nvkm_device *device = pmu->subdev.device;
+
+	if (!pmu->func->init)
+		return 0;
+
+	if (pmu->func->enabled(pmu)) {
+		/* Inhibit interrupts, and wait for idle. */
+		nvkm_wr32(device, 0x10a014, 0x0000ffff);
+		nvkm_msec(device, 2000,
+			if (!nvkm_rd32(device, 0x10a04c))
+				break;
+		);
+
+		nvkm_pmu_reset(pmu);
+	}
+
+	return pmu->func->init(pmu);
 }
 
 static void *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gm200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gm200.c
@@ -23,9 +23,38 @@
  */
 #include "priv.h"
 
+static int
+gm200_pmu_flcn_reset(struct nvkm_falcon *falcon)
+{
+	struct nvkm_pmu *pmu = container_of(falcon, typeof(*pmu), falcon);
+
+	nvkm_falcon_wr32(falcon, 0x014, 0x0000ffff);
+	pmu->func->reset(pmu);
+	return nvkm_falcon_enable(falcon);
+}
+
+const struct nvkm_falcon_func
+gm200_pmu_flcn = {
+	.debug = 0xc08,
+	.fbif = 0xe00,
+	.load_imem = nvkm_falcon_v1_load_imem,
+	.load_dmem = nvkm_falcon_v1_load_dmem,
+	.read_dmem = nvkm_falcon_v1_read_dmem,
+	.bind_context = nvkm_falcon_v1_bind_context,
+	.wait_for_halt = nvkm_falcon_v1_wait_for_halt,
+	.clear_interrupt = nvkm_falcon_v1_clear_interrupt,
+	.set_start_addr = nvkm_falcon_v1_set_start_addr,
+	.start = nvkm_falcon_v1_start,
+	.enable = nvkm_falcon_v1_enable,
+	.disable = nvkm_falcon_v1_disable,
+	.reset = gm200_pmu_flcn_reset,
+	.cmdq = { 0x4a0, 0x4b0, 4 },
+	.msgq = { 0x4c8, 0x4cc, 0 },
+};
+
 static const struct nvkm_pmu_func
 gm200_pmu = {
-	.flcn = &gt215_pmu_flcn,
+	.flcn = &gm200_pmu_flcn,
 	.enabled = gf100_pmu_enabled,
 	.reset = gf100_pmu_reset,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gm20b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gm20b.c
@@ -211,11 +211,12 @@
 
 static const struct nvkm_pmu_func
 gm20b_pmu = {
-	.flcn = &gt215_pmu_flcn,
+	.flcn = &gm200_pmu_flcn,
 	.enabled = gf100_pmu_enabled,
 	.intr = gt215_pmu_intr,
 	.recv = gm20b_pmu_recv,
 	.initmsg = gm20b_pmu_initmsg,
+	.reset = gf100_pmu_reset,
 };
 
 #if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp102.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp102.c
@@ -23,7 +23,7 @@
  */
 #include "priv.h"
 
-static void
+void
 gp102_pmu_reset(struct nvkm_pmu *pmu)
 {
 	struct nvkm_device *device = pmu->subdev.device;
@@ -39,7 +39,7 @@
 
 static const struct nvkm_pmu_func
 gp102_pmu = {
-	.flcn = &gt215_pmu_flcn,
+	.flcn = &gm200_pmu_flcn,
 	.enabled = gp102_pmu_enabled,
 	.reset = gp102_pmu_reset,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c
@@ -78,11 +78,12 @@
 
 static const struct nvkm_pmu_func
 gp10b_pmu = {
-	.flcn = &gt215_pmu_flcn,
+	.flcn = &gm200_pmu_flcn,
 	.enabled = gf100_pmu_enabled,
 	.intr = gt215_pmu_intr,
 	.recv = gm20b_pmu_recv,
 	.initmsg = gm20b_pmu_initmsg,
+	.reset = gp102_pmu_reset,
 };
 
 #if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/priv.h
@@ -41,9 +41,12 @@
 
 bool gf100_pmu_enabled(struct nvkm_pmu *);
 void gf100_pmu_reset(struct nvkm_pmu *);
+void gp102_pmu_reset(struct nvkm_pmu *pmu);
 
 void gk110_pmu_pgob(struct nvkm_pmu *, bool);
 
+extern const struct nvkm_falcon_func gm200_pmu_flcn;
+
 void gm20b_pmu_acr_bld_patch(struct nvkm_acr *, u32, s64);
 void gm20b_pmu_acr_bld_write(struct nvkm_acr *, u32, struct nvkm_acr_lsfw *);
 int gm20b_pmu_acr_boot(struct nvkm_falcon *);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/omapdrm/dss/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/omapdrm/dss/base.c
@@ -139,21 +139,13 @@
 }
 
 int omapdss_device_connect(struct dss_device *dss,
-			   struct omap_dss_device *src,
 			   struct omap_dss_device *dst)
 {
-	dev_dbg(&dss->pdev->dev, "connect(%s, %s)\n",
-		src ? dev_name(src->dev) : "NULL",
+	dev_dbg(&dss->pdev->dev, "connect(%s)\n",
 		dst ? dev_name(dst->dev) : "NULL");
 
-	if (!dst) {
-		/*
-		 * The destination is NULL when the source is connected to a
-		 * bridge instead of a DSS device. Stop here, we will attach
-		 * the bridge later when we will have a DRM encoder.
-		 */
-		return src && src->bridge ? 0 : -EINVAL;
-	}
+	if (!dst)
+		return -EINVAL;
 
 	if (omapdss_device_is_connected(dst))
 		return -EBUSY;
@@ -163,19 +155,14 @@
 	return 0;
 }
 
-void omapdss_device_disconnect(struct omap_dss_device *src,
+void omapdss_device_disconnect(struct dss_device *dss,
 			       struct omap_dss_device *dst)
 {
-	struct dss_device *dss = src ? src->dss : dst->dss;
-
-	dev_dbg(&dss->pdev->dev, "disconnect(%s, %s)\n",
-		src ? dev_name(src->dev) : "NULL",
+	dev_dbg(&dss->pdev->dev, "disconnect(%s)\n",
 		dst ? dev_name(dst->dev) : "NULL");
 
-	if (!dst) {
-		WARN_ON(!src->bridge);
+	if (WARN_ON(!dst))
 		return;
-	}
 
 	if (!dst->id && !omapdss_device_is_connected(dst)) {
 		WARN_ON(1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/omapdrm/dss/dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/omapdrm/dss/dsi.c
@@ -1039,22 +1039,26 @@
 {
 	struct dsi_data *dsi = s->private;
 	unsigned long flags;
-	struct dsi_irq_stats stats;
+	struct dsi_irq_stats *stats;
+
+	stats = kmalloc(sizeof(*stats), GFP_KERNEL);
+	if (!stats)
+		return -ENOMEM;
 
 	spin_lock_irqsave(&dsi->irq_stats_lock, flags);
 
-	stats = dsi->irq_stats;
+	*stats = dsi->irq_stats;
 	memset(&dsi->irq_stats, 0, sizeof(dsi->irq_stats));
 	dsi->irq_stats.last_reset = jiffies;
 
 	spin_unlock_irqrestore(&dsi->irq_stats_lock, flags);
 
 	seq_printf(s, "period %u ms\n",
-			jiffies_to_msecs(jiffies - stats.last_reset));
+			jiffies_to_msecs(jiffies - stats->last_reset));
 
-	seq_printf(s, "irqs %d\n", stats.irq_count);
+	seq_printf(s, "irqs %d\n", stats->irq_count);
 #define PIS(x) \
-	seq_printf(s, "%-20s %10d\n", #x, stats.dsi_irqs[ffs(DSI_IRQ_##x)-1]);
+	seq_printf(s, "%-20s %10d\n", #x, stats->dsi_irqs[ffs(DSI_IRQ_##x)-1]);
 
 	seq_printf(s, "-- DSI%d interrupts --\n", dsi->module_id + 1);
 	PIS(VC0);
@@ -1078,10 +1082,10 @@
 
 #define PIS(x) \
 	seq_printf(s, "%-20s %10d %10d %10d %10d\n", #x, \
-			stats.vc_irqs[0][ffs(DSI_VC_IRQ_##x)-1], \
-			stats.vc_irqs[1][ffs(DSI_VC_IRQ_##x)-1], \
-			stats.vc_irqs[2][ffs(DSI_VC_IRQ_##x)-1], \
-			stats.vc_irqs[3][ffs(DSI_VC_IRQ_##x)-1]);
+			stats->vc_irqs[0][ffs(DSI_VC_IRQ_##x)-1], \
+			stats->vc_irqs[1][ffs(DSI_VC_IRQ_##x)-1], \
+			stats->vc_irqs[2][ffs(DSI_VC_IRQ_##x)-1], \
+			stats->vc_irqs[3][ffs(DSI_VC_IRQ_##x)-1]);
 
 	seq_printf(s, "-- VC interrupts --\n");
 	PIS(CS);
@@ -1097,7 +1101,7 @@
 
 #define PIS(x) \
 	seq_printf(s, "%-20s %10d\n", #x, \
-			stats.cio_irqs[ffs(DSI_CIO_IRQ_##x)-1]);
+			stats->cio_irqs[ffs(DSI_CIO_IRQ_##x)-1]);
 
 	seq_printf(s, "-- CIO interrupts --\n");
 	PIS(ERRSYNCESC1);
@@ -1122,6 +1126,8 @@
 	PIS(ULPSACTIVENOT_ALL1);
 #undef PIS
 
+	kfree(stats);
+
 	return 0;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/omapdrm/dss/dss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/omapdrm/dss/dss.c
@@ -1176,6 +1176,7 @@
 		default:
 			break;
 		}
+		of_node_put(port);
 	}
 }
 
@@ -1208,11 +1209,13 @@
 		default:
 			break;
 		}
+		of_node_put(port);
 	}
 
 	return 0;
 
 error:
+	of_node_put(port);
 	__dss_uninit_ports(dss, i);
 	return r;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/omapdrm/dss/omapdss.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/omapdrm/dss/omapdss.h
@@ -242,9 +242,8 @@
 void omapdss_device_put(struct omap_dss_device *dssdev);
 struct omap_dss_device *omapdss_find_device_by_node(struct device_node *node);
 int omapdss_device_connect(struct dss_device *dss,
-			   struct omap_dss_device *src,
 			   struct omap_dss_device *dst);
-void omapdss_device_disconnect(struct omap_dss_device *src,
+void omapdss_device_disconnect(struct dss_device *dss,
 			       struct omap_dss_device *dst);
 
 int omap_dss_get_num_overlay_managers(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/omapdrm/omap_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/omapdrm/omap_drv.c
@@ -68,7 +68,6 @@
 {
 	struct drm_device *dev = old_state->dev;
 	struct omap_drm_private *priv = dev->dev_private;
-	bool fence_cookie = dma_fence_begin_signalling();
 
 	dispc_runtime_get(priv->dispc);
 
@@ -91,6 +90,8 @@
 		omap_atomic_wait_for_completion(dev, old_state);
 
 		drm_atomic_helper_commit_planes(dev, old_state, 0);
+
+		drm_atomic_helper_commit_hw_done(old_state);
 	} else {
 		/*
 		 * OMAP3 DSS seems to have issues with the work-around above,
@@ -100,11 +101,9 @@
 		drm_atomic_helper_commit_planes(dev, old_state, 0);
 
 		drm_atomic_helper_commit_modeset_enables(dev, old_state);
-	}
-
-	drm_atomic_helper_commit_hw_done(old_state);
 
-	dma_fence_end_signalling(fence_cookie);
+		drm_atomic_helper_commit_hw_done(old_state);
+	}
 
 	/*
 	 * Wait for completion of the page flips to ensure that old buffers
@@ -136,7 +135,7 @@
 	for (i = 0; i < priv->num_pipes; i++) {
 		struct omap_drm_pipeline *pipe = &priv->pipes[i];
 
-		omapdss_device_disconnect(NULL, pipe->output);
+		omapdss_device_disconnect(priv->dss, pipe->output);
 
 		omapdss_device_put(pipe->output);
 		pipe->output = NULL;
@@ -154,7 +153,7 @@
 	int r;
 
 	for_each_dss_output(output) {
-		r = omapdss_device_connect(priv->dss, NULL, output);
+		r = omapdss_device_connect(priv->dss, output);
 		if (r == -EPROBE_DEFER) {
 			omapdss_device_put(output);
 			return r;
@@ -574,6 +573,10 @@
 	soc = soc_device_match(omapdrm_soc_devices);
 	priv->omaprev = soc ? (unsigned int)soc->data : 0;
 	priv->wq = alloc_ordered_workqueue("omapdrm", 0);
+	if (!priv->wq) {
+		ret = -ENOMEM;
+		goto err_alloc_workqueue;
+	}
 
 	mutex_init(&priv->list_lock);
 	INIT_LIST_HEAD(&priv->obj_list);
@@ -621,6 +624,7 @@
 err_gem_deinit:
 	omap_gem_deinit(ddev);
 	destroy_workqueue(priv->wq);
+err_alloc_workqueue:
 	omap_disconnect_pipelines(ddev);
 	drm_dev_put(ddev);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/omapdrm/omap_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/omapdrm/omap_gem.c
@@ -1303,8 +1303,6 @@
 
 	omap_obj = to_omap_bo(obj);
 
-	mutex_lock(&omap_obj->lock);
-
 	omap_obj->sgt = sgt;
 
 	if (sgt->orig_nents == 1) {
@@ -1319,21 +1317,17 @@
 		pages = kcalloc(npages, sizeof(*pages), GFP_KERNEL);
 		if (!pages) {
 			omap_gem_free_object(obj);
-			obj = ERR_PTR(-ENOMEM);
-			goto done;
+			return ERR_PTR(-ENOMEM);
 		}
 
 		omap_obj->pages = pages;
 		ret = drm_prime_sg_to_page_array(sgt, pages, npages);
 		if (ret) {
 			omap_gem_free_object(obj);
-			obj = ERR_PTR(-ENOMEM);
-			goto done;
+			return ERR_PTR(-ENOMEM);
 		}
 	}
 
-done:
-	mutex_unlock(&omap_obj->lock);
 	return obj;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/Kconfig
@@ -83,6 +83,8 @@
 	depends on PM
 	select VIDEOMODE_HELPERS
 	select DRM_DP_AUX_BUS
+	select DRM_DP_HELPER
+	select DRM_KMS_HELPER
 	help
 	  DRM panel driver for dumb panels that need at most a regulator and
 	  a GPIO to be powered up. Optionally a backlight can be attached so
@@ -371,6 +373,8 @@
 	depends on OF
 	depends on BACKLIGHT_CLASS_DEVICE
 	depends on PM
+	select DRM_DISPLAY_DP_HELPER
+	select DRM_DISPLAY_HELPER
 	select DRM_DP_AUX_BUS
 	help
 	  DRM panel driver for the Samsung ATNA33XC20 panel. This panel can't
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-arm-versatile.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-arm-versatile.c
@@ -267,6 +267,8 @@
 	connector->display_info.bus_flags = vpanel->panel_type->bus_flags;
 
 	mode = drm_mode_duplicate(connector->dev, &vpanel->panel_type->mode);
+	if (!mode)
+		return -ENOMEM;
 	drm_mode_set_name(mode);
 	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
@@ -36,6 +36,7 @@
 	const struct panel_init_cmd *init_cmds;
 	unsigned int lanes;
 	bool discharge_on_disable;
+	bool lp11_before_reset;
 };
 
 struct boe_panel {
@@ -551,6 +552,14 @@
 
 	usleep_range(5000, 10000);
 
+	if (boe->desc->lp11_before_reset) {
+		ret = mipi_dsi_dcs_nop(boe->dsi);
+		if (ret < 0) {
+			dev_err(&boe->dsi->dev, "Failed to send NOP: %d\n", ret);
+			goto poweroff;
+		}
+		usleep_range(1000, 2000);
+	}
 	gpiod_set_value(boe->enable_gpio, 1);
 	usleep_range(1000, 2000);
 	gpiod_set_value(boe->enable_gpio, 0);
@@ -569,13 +578,13 @@
 	return 0;
 
 poweroff:
+	gpiod_set_value(boe->enable_gpio, 0);
 	regulator_disable(boe->avee);
 poweroffavdd:
 	regulator_disable(boe->avdd);
 poweroff1v8:
 	usleep_range(5000, 7000);
 	regulator_disable(boe->pp1800);
-	gpiod_set_value(boe->enable_gpio, 0);
 
 	return ret;
 }
@@ -692,6 +701,7 @@
 	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
 		      MIPI_DSI_MODE_LPM,
 	.init_cmds = auo_b101uan08_3_init_cmd,
+	.lp11_before_reset = true,
 };
 
 static const struct drm_display_mode boe_tv105wum_nw0_default_mode = {
@@ -719,6 +729,7 @@
 	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
 		      MIPI_DSI_MODE_LPM,
 	.init_cmds = boe_init_cmd,
+	.lp11_before_reset = true,
 };
 
 static int boe_panel_get_modes(struct drm_panel *panel,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-elida-kd35t133.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-elida-kd35t133.c
@@ -112,6 +112,8 @@
 		return ret;
 	}
 
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
 	regulator_disable(ctx->iovcc);
 	regulator_disable(ctx->vdd);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
@@ -227,7 +227,13 @@
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->lanes = 4;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		drm_panel_remove(&ctx->panel);
+		return ret;
+	}
+
+	return 0;
 }
 
 static int feiyang_dsi_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
@@ -420,7 +420,7 @@
 
 	ili9341_dpi_init(ili);
 
-	return ret;
+	return 0;
 }
 
 static int ili9341_dpi_enable(struct drm_panel *panel)
@@ -612,8 +612,10 @@
 	int ret;
 
 	vcc = devm_regulator_get_optional(dev, "vcc");
-	if (IS_ERR(vcc))
+	if (IS_ERR(vcc)) {
 		dev_err(dev, "get optional vcc failed\n");
+		vcc = NULL;
+	}
 
 	dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver,
 				    struct mipi_dbi_dev, drm);
@@ -714,18 +716,18 @@
 
 	reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(reset))
-		dev_err(dev, "Failed to get gpio 'reset'\n");
+		return dev_err_probe(dev, PTR_ERR(reset), "Failed to get gpio 'reset'\n");
 
 	dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
 	if (IS_ERR(dc))
-		dev_err(dev, "Failed to get gpio 'dc'\n");
+		return dev_err_probe(dev, PTR_ERR(dc), "Failed to get gpio 'dc'\n");
 
 	if (!strcmp(id->name, "sf-tc240t-9370-t"))
 		return ili9341_dpi_probe(spi, dc, reset);
 	else if (!strcmp(id->name, "yx240qv29"))
 		return ili9341_dbi_probe(spi, dc, reset);
 
-	return -1;
+	return -ENODEV;
 }
 
 static int ili9341_remove(struct spi_device *spi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
@@ -506,10 +506,10 @@
 	msleep(5);
 
 	/* And reset it */
-	gpiod_set_value(ctx->reset, 1);
+	gpiod_set_value_cansleep(ctx->reset, 1);
 	msleep(20);
 
-	gpiod_set_value(ctx->reset, 0);
+	gpiod_set_value_cansleep(ctx->reset, 0);
 	msleep(20);
 
 	for (i = 0; i < ctx->desc->init_length; i++) {
@@ -564,7 +564,7 @@
 
 	mipi_dsi_dcs_enter_sleep_mode(ctx->dsi);
 	regulator_disable(ctx->power);
-	gpiod_set_value(ctx->reset, 1);
+	gpiod_set_value_cansleep(ctx->reset, 1);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-innolux-p079zca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-innolux-p079zca.c
@@ -484,6 +484,7 @@
 static int innolux_panel_probe(struct mipi_dsi_device *dsi)
 {
 	const struct panel_desc *desc;
+	struct innolux_panel *innolux;
 	int err;
 
 	desc = of_device_get_match_data(&dsi->dev);
@@ -495,7 +496,14 @@
 	if (err < 0)
 		return err;
 
-	return mipi_dsi_attach(dsi);
+	err = mipi_dsi_attach(dsi);
+	if (err < 0) {
+		innolux = mipi_dsi_get_drvdata(dsi);
+		innolux_panel_del(innolux);
+		return err;
+	}
+
+	return 0;
 }
 
 static int innolux_panel_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-jdi-lt070me05000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-jdi-lt070me05000.c
@@ -473,7 +473,13 @@
 	if (ret < 0)
 		return ret;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		jdi_panel_del(jdi);
+		return ret;
+	}
+
+	return 0;
 }
 
 static int jdi_panel_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-kingdisplay-kd097d04.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-kingdisplay-kd097d04.c
@@ -406,7 +406,13 @@
 	if (err < 0)
 		return err;
 
-	return mipi_dsi_attach(dsi);
+	err = mipi_dsi_attach(dsi);
+	if (err < 0) {
+		kingdisplay_panel_del(kingdisplay);
+		return err;
+	}
+
+	return 0;
 }
 
 static int kingdisplay_panel_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
@@ -656,7 +656,13 @@
 	if (err < 0)
 		return err;
 
-	return mipi_dsi_attach(dsi);
+	err = mipi_dsi_attach(dsi);
+	if (err < 0) {
+		drm_panel_remove(&pinfo->base);
+		return err;
+	}
+
+	return 0;
 }
 
 static int nt36672a_panel_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-orisetech-otm8009a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-orisetech-otm8009a.c
@@ -444,7 +444,7 @@
 		       DRM_MODE_CONNECTOR_DSI);
 
 	ctx->bl_dev = devm_backlight_device_register(dev, dev_name(dev),
-						     dsi->host->dev, ctx,
+						     dev, ctx,
 						     &otm8009a_backlight_ops,
 						     NULL);
 	if (IS_ERR(ctx->bl_dev)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-panasonic-vvx10f034n00.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-panasonic-vvx10f034n00.c
@@ -241,7 +241,13 @@
 	if (ret < 0)
 		return ret;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		wuxga_nt_panel_del(wuxga_nt);
+		return ret;
+	}
+
+	return 0;
 }
 
 static int wuxga_nt_panel_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c
@@ -229,7 +229,7 @@
 
 	ret = i2c_smbus_write_byte_data(ts->i2c, reg, val);
 	if (ret)
-		dev_err(&ts->dsi->dev, "I2C write failed: %d\n", ret);
+		dev_err(&ts->i2c->dev, "I2C write failed: %d\n", ret);
 }
 
 static int rpi_touchscreen_write(struct rpi_touchscreen *ts, u16 reg, u32 val)
@@ -265,7 +265,7 @@
 	return 0;
 }
 
-static int rpi_touchscreen_enable(struct drm_panel *panel)
+static int rpi_touchscreen_prepare(struct drm_panel *panel)
 {
 	struct rpi_touchscreen *ts = panel_to_ts(panel);
 	int i;
@@ -295,6 +295,13 @@
 	rpi_touchscreen_write(ts, DSI_STARTDSI, 0x01);
 	msleep(100);
 
+	return 0;
+}
+
+static int rpi_touchscreen_enable(struct drm_panel *panel)
+{
+	struct rpi_touchscreen *ts = panel_to_ts(panel);
+
 	/* Turn on the backlight. */
 	rpi_touchscreen_i2c_write(ts, REG_PWM, 255);
 
@@ -349,7 +356,7 @@
 static const struct drm_panel_funcs rpi_touchscreen_funcs = {
 	.disable = rpi_touchscreen_disable,
 	.unprepare = rpi_touchscreen_noop,
-	.prepare = rpi_touchscreen_noop,
+	.prepare = rpi_touchscreen_prepare,
 	.enable = rpi_touchscreen_enable,
 	.get_modes = rpi_touchscreen_get_modes,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-ronbo-rb070d30.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-ronbo-rb070d30.c
@@ -199,7 +199,13 @@
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->lanes = 4;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		drm_panel_remove(&ctx->panel);
+		return ret;
+	}
+
+	return 0;
 }
 
 static int rb070d30_panel_dsi_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
@@ -692,7 +692,9 @@
 
 	dsi->lanes = 4;
 	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS |
+		MIPI_DSI_MODE_VIDEO_NO_HFP | MIPI_DSI_MODE_VIDEO_NO_HBP |
+		MIPI_DSI_MODE_VIDEO_NO_HSA | MIPI_DSI_MODE_NO_EOT_PACKET;
 
 	ctx->supplies[0].supply = "vdd3";
 	ctx->supplies[1].supply = "vci";
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-samsung-s6e63j0x03.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-samsung-s6e63j0x03.c
@@ -446,7 +446,8 @@
 
 	dsi->lanes = 1;
 	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_MODE_NO_EOT_PACKET;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO_NO_HFP |
+		MIPI_DSI_MODE_VIDEO_NO_HBP | MIPI_DSI_MODE_VIDEO_NO_HSA;
 
 	ctx->supplies[0].supply = "vdd3";
 	ctx->supplies[1].supply = "vci";
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-samsung-s6e88a0-ams452ef01.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-samsung-s6e88a0-ams452ef01.c
@@ -247,6 +247,7 @@
 	ret = mipi_dsi_attach(dsi);
 	if (ret < 0) {
 		dev_err(dev, "Failed to attach to DSI host: %d\n", ret);
+		drm_panel_remove(&ctx->panel);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-samsung-s6e8aa0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-samsung-s6e8aa0.c
@@ -990,8 +990,6 @@
 	dsi->lanes = 4;
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST
-		| MIPI_DSI_MODE_VIDEO_NO_HFP | MIPI_DSI_MODE_VIDEO_NO_HBP
-		| MIPI_DSI_MODE_VIDEO_NO_HSA | MIPI_DSI_MODE_NO_EOT_PACKET
 		| MIPI_DSI_MODE_VSYNC_FLUSH | MIPI_DSI_MODE_VIDEO_AUTO_VERT;
 
 	ret = s6e8aa0_parse_dt(ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-samsung-sofef00.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-samsung-sofef00.c
@@ -302,6 +302,7 @@
 	ret = mipi_dsi_attach(dsi);
 	if (ret < 0) {
 		dev_err(dev, "Failed to attach to DSI host: %d\n", ret);
+		drm_panel_remove(&ctx->panel);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-sharp-ls043t1le01.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-sharp-ls043t1le01.c
@@ -192,15 +192,15 @@
 }
 
 static const struct drm_display_mode default_mode = {
-	.clock = 41118,
+	.clock = (540 + 48 + 32 + 80) * (960 + 3 + 10 + 15) * 60 / 1000,
 	.hdisplay = 540,
 	.hsync_start = 540 + 48,
-	.hsync_end = 540 + 48 + 80,
-	.htotal = 540 + 48 + 80 + 32,
+	.hsync_end = 540 + 48 + 32,
+	.htotal = 540 + 48 + 32 + 80,
 	.vdisplay = 960,
 	.vsync_start = 960 + 3,
-	.vsync_end = 960 + 3 + 15,
-	.vtotal = 960 + 3 + 15 + 1,
+	.vsync_end = 960 + 3 + 10,
+	.vtotal = 960 + 3 + 10 + 15,
 };
 
 static int sharp_nt_panel_get_modes(struct drm_panel *panel,
@@ -280,6 +280,7 @@
 	dsi->lanes = 2;
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
+			MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
 			MIPI_DSI_MODE_VIDEO_HSE |
 			MIPI_DSI_CLOCK_NON_CONTINUOUS |
 			MIPI_DSI_MODE_NO_EOT_PACKET;
@@ -296,7 +297,13 @@
 	if (ret < 0)
 		return ret;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		sharp_nt_panel_del(sharp_nt);
+		return ret;
+	}
+
+	return 0;
 }
 
 static int sharp_nt_panel_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-simple.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-simple.c
@@ -721,6 +721,7 @@
 		err = panel_dpi_probe(dev, panel);
 		if (err)
 			goto free_ddc;
+		desc = panel->desc;
 	} else {
 		if (!of_get_display_timing(dev->of_node, "panel-timing", &dt))
 			panel_simple_parse_panel_timing_node(dev, panel, &dt);
@@ -861,7 +862,7 @@
 static const struct panel_desc ampire_am_1280800n3tzqw_t00h = {
 	.modes = &ampire_am_1280800n3tzqw_t00h_mode,
 	.num_modes = 1,
-	.bpc = 6,
+	.bpc = 8,
 	.size = {
 		.width = 217,
 		.height = 136,
@@ -889,8 +890,8 @@
 	.num_modes = 1,
 	.bpc = 8,
 	.size = {
-		.width = 105,
-		.height = 67,
+		.width = 99,
+		.height = 58,
 	},
 	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
 };
@@ -1257,21 +1258,21 @@
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
-static const struct drm_display_mode auo_g121ean01_mode = {
-	.clock = 66700,
-	.hdisplay = 1280,
-	.hsync_start = 1280 + 58,
-	.hsync_end = 1280 + 58 + 8,
-	.htotal = 1280 + 58 + 8 + 70,
-	.vdisplay = 800,
-	.vsync_start = 800 + 6,
-	.vsync_end = 800 + 6 + 4,
-	.vtotal = 800 + 6 + 4 + 10,
+static const struct display_timing auo_g121ean01_timing = {
+	.pixelclock = { 60000000, 74400000, 90000000 },
+	.hactive = { 1280, 1280, 1280 },
+	.hfront_porch = { 20, 50, 100 },
+	.hback_porch = { 20, 50, 100 },
+	.hsync_len = { 30, 100, 200 },
+	.vactive = { 800, 800, 800 },
+	.vfront_porch = { 2, 10, 25 },
+	.vback_porch = { 2, 10, 25 },
+	.vsync_len = { 4, 18, 50 },
 };
 
 static const struct panel_desc auo_g121ean01 = {
-	.modes = &auo_g121ean01_mode,
-	.num_modes = 1,
+	.timings = &auo_g121ean01_timing,
+	.num_timings = 1,
 	.bpc = 8,
 	.size = {
 		.width = 261,
@@ -1447,7 +1448,9 @@
 	.delay = {
 		.disable = 5,
 		.unprepare = 1000,
-	}
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
+	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
 static const struct drm_display_mode avic_tm070ddh03_mode = {
@@ -2468,6 +2471,7 @@
 		.height = 54,
 	},
 	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
 	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
 };
 
@@ -2509,7 +2513,7 @@
 static const struct panel_desc innolux_g070y2_l01 = {
 	.timings = &innolux_g070y2_l01_timing,
 	.num_timings = 1,
-	.bpc = 6,
+	.bpc = 8,
 	.size = {
 		.width = 152,
 		.height = 91,
@@ -2521,19 +2525,20 @@
 		.unprepare = 800,
 	},
 	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH,
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
-	.hfront_porch = { 41, 80, 100 },
-	.hback_porch = { 40, 79, 99 },
-	.hsync_len = { 1, 1, 1 },
+	.hfront_porch = { 30, 60, 70 },
+	.hback_porch = { 30, 60, 70 },
+	.hsync_len = { 22, 40, 60 },
 	.vactive = { 800, 800, 800 },
-	.vfront_porch = { 5, 11, 14 },
-	.vback_porch = { 4, 11, 14 },
-	.vsync_len = { 1, 1, 1 },
+	.vfront_porch = { 3, 8, 14 },
+	.vback_porch = { 3, 8, 14 },
+	.vsync_len = { 4, 7, 12 },
 	.flags = DISPLAY_FLAGS_DE_HIGH,
 };
 
@@ -2550,6 +2555,7 @@
 		.disable = 200,
 	},
 	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH,
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
@@ -2577,7 +2583,7 @@
 		.enable = 200,
 		.disable = 20,
 	},
-	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
+	.bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG,
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
@@ -2607,6 +2613,9 @@
 		.unprepare = 200,
 		.disable = 400,
 	},
+	.bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH,
+	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
 static const struct drm_display_mode innolux_n116bca_ea1_mode = {
@@ -2864,6 +2873,7 @@
 	.vfront_porch = { 3, 5, 10 },
 	.vback_porch = { 2, 5, 10 },
 	.vsync_len = { 5, 5, 5 },
+	.flags = DISPLAY_FLAGS_DE_HIGH,
 };
 
 static const struct panel_desc koe_tx26d202vm0bwa = {
@@ -3088,6 +3098,7 @@
 static const struct panel_desc logictechno_lt161010_2nh = {
 	.timings = &logictechno_lt161010_2nh_timing,
 	.num_timings = 1,
+	.bpc = 6,
 	.size = {
 		.width = 154,
 		.height = 86,
@@ -3117,6 +3128,7 @@
 static const struct panel_desc logictechno_lt170410_2whc = {
 	.timings = &logictechno_lt170410_2whc_timing,
 	.num_timings = 1,
+	.bpc = 8,
 	.size = {
 		.width = 217,
 		.height = 136,
@@ -3646,6 +3658,7 @@
 	.vsync_start = 480 + 49,
 	.vsync_end = 480 + 49 + 2,
 	.vtotal = 480 + 49 + 2 + 22,
+	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
 };
 
 static const struct panel_desc powertip_ph800480t013_idf02  = {
@@ -4164,6 +4177,7 @@
 	},
 	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH,
 };
 
 static const struct panel_desc tianma_tm070jvhg33 = {
@@ -4176,6 +4190,7 @@
 	},
 	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH,
 };
 
 static const struct display_timing tianma_tm070rvhg71_timing = {
@@ -4438,6 +4453,31 @@
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct drm_display_mode mchp_ac69t88a_mode = {
+	.clock = 25000,
+	.hdisplay = 800,
+	.hsync_start = 800 + 88,
+	.hsync_end = 800 + 88 + 5,
+	.htotal = 800 + 88 + 5 + 40,
+	.vdisplay = 480,
+	.vsync_start = 480 + 23,
+	.vsync_end = 480 + 23 + 5,
+	.vtotal = 480 + 23 + 5 + 1,
+};
+
+static const struct panel_desc mchp_ac69t88a = {
+	.modes = &mchp_ac69t88a_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 108,
+		.height = 65,
+	},
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH,
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA,
+	.connector_type = DRM_MODE_CONNECTOR_LVDS,
+};
+
 static const struct drm_display_mode arm_rtsm_mode[] = {
 	{
 		.clock = 65000,
@@ -4901,6 +4941,9 @@
 		.compatible = "yes-optoelectronics,ytc700tlag-05-201c",
 		.data = &yes_optoelectronics_ytc700tlag_05_201c,
 	}, {
+		.compatible = "microchip,ac69t88a",
+		.data = &mchp_ac69t88a,
+	}, {
 		/* Must be the last entry */
 		.compatible = "panel-dpi",
 		.data = &panel_dpi,
@@ -4984,6 +5027,33 @@
 	.lanes = 4,
 };
 
+static const struct drm_display_mode auo_b101uan01_mode = {
+	.clock = 154500,
+	.hdisplay = 1920,
+	.hsync_start = 1920 + 185,
+	.hsync_end = 1920 + 185,
+	.htotal = 1920 + 185 + 925,
+	.vdisplay = 1200,
+	.vsync_start = 1200 + 3,
+	.vsync_end = 1200 + 3 + 5,
+	.vtotal = 1200 + 3 + 5 + 4,
+};
+
+static const struct panel_desc_dsi auo_b101uan01 = {
+	.desc = {
+		.modes = &auo_b101uan01_mode,
+		.num_modes = 1,
+		.bpc = 8,
+		.size = {
+			.width = 108,
+			.height = 272,
+		},
+	},
+	.flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE,
+	.format = MIPI_DSI_FMT_RGB888,
+	.lanes = 4,
+};
+
 static const struct drm_display_mode boe_tv080wum_nl0_mode = {
 	.clock = 160000,
 	.hdisplay = 1200,
@@ -5163,6 +5233,9 @@
 		.compatible = "auo,b080uan01",
 		.data = &auo_b080uan01
 	}, {
+		.compatible = "auo,b101uan01",
+		.data = &auo_b101uan01
+	}, {
 		.compatible = "boe,tv080wum-nl0",
 		.data = &boe_tv080wum_nl0
 	}, {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-sitronix-st7701.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-sitronix-st7701.c
@@ -384,7 +384,15 @@
 	st7701->dsi = dsi;
 	st7701->desc = desc;
 
-	return mipi_dsi_attach(dsi);
+	ret = mipi_dsi_attach(dsi);
+	if (ret)
+		goto err_attach;
+
+	return 0;
+
+err_attach:
+	drm_panel_remove(&st7701->panel);
+	return ret;
 }
 
 static int st7701_dsi_remove(struct mipi_dsi_device *dsi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-sitronix-st7703.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-sitronix-st7703.c
@@ -428,29 +428,30 @@
 		return 0;
 
 	dev_dbg(ctx->dev, "Resetting the panel\n");
-	ret = regulator_enable(ctx->vcc);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
+	ret = regulator_enable(ctx->iovcc);
 	if (ret < 0) {
-		dev_err(ctx->dev, "Failed to enable vcc supply: %d\n", ret);
+		dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret);
 		return ret;
 	}
-	ret = regulator_enable(ctx->iovcc);
+
+	ret = regulator_enable(ctx->vcc);
 	if (ret < 0) {
-		dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret);
-		goto disable_vcc;
+		dev_err(ctx->dev, "Failed to enable vcc supply: %d\n", ret);
+		regulator_disable(ctx->iovcc);
+		return ret;
 	}
 
-	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
-	usleep_range(20, 40);
+	/* Give power supplies time to stabilize before deasserting reset. */
+	usleep_range(10000, 20000);
+
 	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
-	msleep(20);
+	usleep_range(15000, 20000);
 
 	ctx->prepared = true;
 
 	return 0;
-
-disable_vcc:
-	regulator_disable(ctx->vcc);
-	return ret;
 }
 
 static int st7703_get_modes(struct drm_panel *panel,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-tpo-tpg110.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-tpo-tpg110.c
@@ -379,6 +379,8 @@
 	connector->display_info.bus_flags = tpg->panel_mode->bus_flags;
 
 	mode = drm_mode_duplicate(connector->dev, &tpg->panel_mode->mode);
+	if (!mode)
+		return -ENOMEM;
 	drm_mode_set_name(mode);
 	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panel/panel-visionox-rm69299.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panel/panel-visionox-rm69299.c
@@ -261,8 +261,6 @@
 	struct visionox_rm69299 *ctx = mipi_dsi_get_drvdata(dsi);
 
 	mipi_dsi_detach(ctx->dsi);
-	mipi_dsi_device_unregister(ctx->dsi);
-
 	drm_panel_remove(&ctx->panel);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/Kconfig
@@ -3,7 +3,8 @@
 config DRM_PANFROST
 	tristate "Panfrost (DRM support for ARM Mali Midgard/Bifrost GPUs)"
 	depends on DRM
-	depends on ARM || ARM64 || (COMPILE_TEST && !GENERIC_ATOMIC64)
+	depends on ARM || ARM64 || COMPILE_TEST
+	depends on !GENERIC_ATOMIC64    # for IOMMU_IO_PGTABLE_LPAE
 	depends on MMU
 	select DRM_SCHED
 	select IOMMU_SUPPORT
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_devfreq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_devfreq.c
@@ -132,6 +132,17 @@
 		return PTR_ERR(opp);
 
 	panfrost_devfreq_profile.initial_freq = cur_freq;
+
+	/*
+	 * Set the recommend OPP this will enable and configure the regulator
+	 * if any and will avoid a switch off by regulator_late_cleanup()
+	 */
+	ret = dev_pm_opp_set_opp(dev, opp);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "Couldn't set recommended OPP\n");
+		return ret;
+	}
+
 	dev_pm_opp_put(opp);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_drv.c
@@ -82,6 +82,7 @@
 	struct panfrost_gem_object *bo;
 	struct drm_panfrost_create_bo *args = data;
 	struct panfrost_gem_mapping *mapping;
+	int ret;
 
 	if (!args->size || args->pad ||
 	    (args->flags & ~(PANFROST_BO_NOEXEC | PANFROST_BO_HEAP)))
@@ -92,21 +93,29 @@
 	    !(args->flags & PANFROST_BO_NOEXEC))
 		return -EINVAL;
 
-	bo = panfrost_gem_create_with_handle(file, dev, args->size, args->flags,
-					     &args->handle);
+	bo = panfrost_gem_create(dev, args->size, args->flags);
 	if (IS_ERR(bo))
 		return PTR_ERR(bo);
 
+	ret = drm_gem_handle_create(file, &bo->base.base, &args->handle);
+	if (ret)
+		goto out;
+
 	mapping = panfrost_gem_mapping_get(bo, priv);
-	if (!mapping) {
-		drm_gem_object_put(&bo->base.base);
-		return -EINVAL;
+	if (mapping) {
+		args->offset = mapping->mmnode.start << PAGE_SHIFT;
+		panfrost_gem_mapping_put(mapping);
+	} else {
+		/* This can only happen if the handle from
+		 * drm_gem_handle_create() has already been guessed and freed
+		 * by user space
+		 */
+		ret = -EINVAL;
 	}
 
-	args->offset = mapping->mmnode.start << PAGE_SHIFT;
-	panfrost_gem_mapping_put(mapping);
-
-	return 0;
+out:
+	drm_gem_object_put(&bo->base.base);
+	return ret;
 }
 
 /**
@@ -418,12 +427,12 @@
 		}
 	}
 
-	args->retained = drm_gem_shmem_madvise(gem_obj, args->madv);
+	args->retained = drm_gem_shmem_madvise(&bo->base, args->madv);
 
 	if (args->retained) {
 		if (args->madv == PANFROST_MADV_DONTNEED)
-			list_add_tail(&bo->base.madv_list,
-				      &pfdev->shrinker_list);
+			list_move_tail(&bo->base.madv_list,
+				       &pfdev->shrinker_list);
 		else if (args->madv == PANFROST_MADV_WILLNEED)
 			list_del_init(&bo->base.madv_list);
 	}
@@ -678,3 +687,4 @@
 MODULE_AUTHOR("Panfrost Project Developers");
 MODULE_DESCRIPTION("Panfrost DRM Driver");
 MODULE_LICENSE("GPL v2");
+MODULE_SOFTDEP("pre: governor_simpleondemand");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_gem.c
@@ -49,7 +49,7 @@
 		kvfree(bo->sgts);
 	}
 
-	drm_gem_shmem_free_object(obj);
+	drm_gem_shmem_free(&bo->base);
 }
 
 struct panfrost_gem_mapping *
@@ -187,23 +187,25 @@
 
 static int panfrost_gem_pin(struct drm_gem_object *obj)
 {
-	if (to_panfrost_bo(obj)->is_heap)
+	struct panfrost_gem_object *bo = to_panfrost_bo(obj);
+
+	if (bo->is_heap)
 		return -EINVAL;
 
-	return drm_gem_shmem_pin(obj);
+	return drm_gem_shmem_pin(&bo->base);
 }
 
 static const struct drm_gem_object_funcs panfrost_gem_funcs = {
 	.free = panfrost_gem_free_object,
 	.open = panfrost_gem_open,
 	.close = panfrost_gem_close,
-	.print_info = drm_gem_shmem_print_info,
+	.print_info = drm_gem_shmem_object_print_info,
 	.pin = panfrost_gem_pin,
-	.unpin = drm_gem_shmem_unpin,
-	.get_sg_table = drm_gem_shmem_get_sg_table,
-	.vmap = drm_gem_shmem_vmap,
-	.vunmap = drm_gem_shmem_vunmap,
-	.mmap = drm_gem_shmem_mmap,
+	.unpin = drm_gem_shmem_object_unpin,
+	.get_sg_table = drm_gem_shmem_object_get_sg_table,
+	.vmap = drm_gem_shmem_object_vmap,
+	.vunmap = drm_gem_shmem_object_vunmap,
+	.mmap = drm_gem_shmem_object_mmap,
 };
 
 /**
@@ -232,12 +234,8 @@
 }
 
 struct panfrost_gem_object *
-panfrost_gem_create_with_handle(struct drm_file *file_priv,
-				struct drm_device *dev, size_t size,
-				u32 flags,
-				uint32_t *handle)
+panfrost_gem_create(struct drm_device *dev, size_t size, u32 flags)
 {
-	int ret;
 	struct drm_gem_shmem_object *shmem;
 	struct panfrost_gem_object *bo;
 
@@ -253,16 +251,6 @@
 	bo->noexec = !!(flags & PANFROST_BO_NOEXEC);
 	bo->is_heap = !!(flags & PANFROST_BO_HEAP);
 
-	/*
-	 * Allocate an id of idr table where the obj is registered
-	 * and handle has the id what user can see.
-	 */
-	ret = drm_gem_handle_create(file_priv, &shmem->base, handle);
-	/* drop reference from allocate - handle holds it now. */
-	drm_gem_object_put(&shmem->base);
-	if (ret)
-		return ERR_PTR(ret);
-
 	return bo;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_gem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_gem.h
@@ -69,10 +69,7 @@
 				   struct sg_table *sgt);
 
 struct panfrost_gem_object *
-panfrost_gem_create_with_handle(struct drm_file *file_priv,
-				struct drm_device *dev, size_t size,
-				u32 flags,
-				uint32_t *handle);
+panfrost_gem_create(struct drm_device *dev, size_t size, u32 flags);
 
 int panfrost_gem_open(struct drm_gem_object *obj, struct drm_file *file_priv);
 void panfrost_gem_close(struct drm_gem_object *obj,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_gem_shrinker.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_gem_shrinker.c
@@ -52,7 +52,7 @@
 		goto unlock_mappings;
 
 	panfrost_gem_teardown_mappings_locked(bo);
-	drm_gem_shmem_purge_locked(obj);
+	drm_gem_shmem_purge_locked(&bo->base);
 	ret = true;
 
 	mutex_unlock(&shmem->pages_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_gpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_gpu.c
@@ -158,7 +158,6 @@
 struct panfrost_model {
 	const char *name;
 	u32 id;
-	u32 id_mask;
 	u64 features;
 	u64 issues;
 	struct {
@@ -360,8 +359,11 @@
 
 	panfrost_gpu_init_features(pfdev);
 
-	dma_set_mask_and_coherent(pfdev->dev,
+	err = dma_set_mask_and_coherent(pfdev->dev,
 		DMA_BIT_MASK(FIELD_GET(0xff00, pfdev->features.mmu_features)));
+	if (err)
+		return err;
+
 	dma_set_max_seg_size(pfdev->dev, UINT_MAX);
 
 	irq = platform_get_irq_byname(to_platform_device(pfdev->dev), "gpu");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_mmu.c
@@ -253,7 +253,7 @@
 	if (pm_runtime_active(pfdev->dev))
 		mmu_hw_do_operation(pfdev, mmu, iova, size, AS_COMMAND_FLUSH_PT);
 
-	pm_runtime_put_sync_autosuspend(pfdev->dev);
+	pm_runtime_put_autosuspend(pfdev->dev);
 }
 
 static int mmu_map_sg(struct panfrost_device *pfdev, struct panfrost_mmu *mmu,
@@ -288,7 +288,8 @@
 int panfrost_mmu_map(struct panfrost_gem_mapping *mapping)
 {
 	struct panfrost_gem_object *bo = mapping->obj;
-	struct drm_gem_object *obj = &bo->base.base;
+	struct drm_gem_shmem_object *shmem = &bo->base;
+	struct drm_gem_object *obj = &shmem->base;
 	struct panfrost_device *pfdev = to_panfrost_device(obj->dev);
 	struct sg_table *sgt;
 	int prot = IOMMU_READ | IOMMU_WRITE;
@@ -299,7 +300,7 @@
 	if (bo->noexec)
 		prot |= IOMMU_NOEXEC;
 
-	sgt = drm_gem_shmem_get_pages_sgt(obj);
+	sgt = drm_gem_shmem_get_pages_sgt(shmem);
 	if (WARN_ON(IS_ERR(sgt)))
 		return PTR_ERR(sgt);
 
@@ -464,11 +465,19 @@
 	mapping_set_unevictable(mapping);
 
 	for (i = page_offset; i < page_offset + NUM_FAULT_PAGES; i++) {
+		/* Can happen if the last fault only partially filled this
+		 * section of the pages array before failing. In that case
+		 * we skip already filled pages.
+		 */
+		if (pages[i])
+			continue;
+
 		pages[i] = shmem_read_mapping_page(mapping, i);
 		if (IS_ERR(pages[i])) {
 			mutex_unlock(&bo->base.pages_lock);
 			ret = PTR_ERR(pages[i]);
-			goto err_pages;
+			pages[i] = NULL;
+			goto err_bo;
 		}
 	}
 
@@ -478,7 +487,7 @@
 	ret = sg_alloc_table_from_pages(sgt, pages + page_offset,
 					NUM_FAULT_PAGES, 0, SZ_2M, GFP_KERNEL);
 	if (ret)
-		goto err_pages;
+		goto err_bo;
 
 	ret = dma_map_sgtable(pfdev->dev, sgt, DMA_BIDIRECTIONAL, 0);
 	if (ret)
@@ -498,10 +507,8 @@
 
 err_map:
 	sg_free_table(sgt);
-err_pages:
-	drm_gem_shmem_put_pages(&bo->base);
 err_bo:
-	drm_gem_object_put(&bo->base.base);
+	panfrost_gem_mapping_put(bomapping);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/panfrost/panfrost_perfcnt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/panfrost/panfrost_perfcnt.c
@@ -105,7 +105,7 @@
 		goto err_close_bo;
 	}
 
-	ret = drm_gem_shmem_vmap(&bo->base, &map);
+	ret = drm_gem_shmem_vmap(bo, &map);
 	if (ret)
 		goto err_put_mapping;
 	perfcnt->buf = map.vaddr;
@@ -164,7 +164,7 @@
 	return 0;
 
 err_vunmap:
-	drm_gem_shmem_vunmap(&bo->base, &map);
+	drm_gem_shmem_vunmap(bo, &map);
 err_put_mapping:
 	panfrost_gem_mapping_put(perfcnt->mapping);
 err_close_bo:
@@ -194,7 +194,7 @@
 		  GPU_PERFCNT_CFG_MODE(GPU_PERFCNT_CFG_MODE_OFF));
 
 	perfcnt->user = NULL;
-	drm_gem_shmem_vunmap(&perfcnt->mapping->obj->base.base, &map);
+	drm_gem_shmem_vunmap(&perfcnt->mapping->obj->base, &map);
 	perfcnt->buf = NULL;
 	panfrost_gem_close(&perfcnt->mapping->obj->base.base, file_priv);
 	panfrost_mmu_as_put(pfdev, perfcnt->mapping->mmu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/pl111/pl111_versatile.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/pl111/pl111_versatile.c
@@ -402,6 +402,7 @@
 		if (of_device_is_compatible(child, "arm,pl111")) {
 			has_coretile_clcd = true;
 			ct_clcd = child;
+			of_node_put(child);
 			break;
 		}
 		if (of_device_is_compatible(child, "arm,hdlcd")) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/qxl/qxl_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/qxl/qxl_display.c
@@ -233,6 +233,9 @@
 		return 0;
 
 	mode = drm_cvt_mode(dev, width, height, 60, false, false, false);
+	if (!mode)
+		return 0;
+
 	if (preferred)
 		mode->type |= DRM_MODE_TYPE_PREFERRED;
 	mode->hdisplay = width;
@@ -1221,6 +1224,9 @@
 	if (!qdev->monitors_config_bo)
 		return 0;
 
+	kfree(qdev->dumb_heads);
+	qdev->dumb_heads = NULL;
+
 	qdev->monitors_config = NULL;
 	qdev->ram_header->monitors_config = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/qxl/qxl_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/qxl/qxl_drv.h
@@ -318,7 +318,7 @@
 				      u32 domain,
 				      size_t size,
 				      struct qxl_surface *surf,
-				      struct qxl_bo **qobj,
+				      struct drm_gem_object **gobj,
 				      uint32_t *handle);
 void qxl_gem_object_free(struct drm_gem_object *gobj);
 int qxl_gem_object_open(struct drm_gem_object *obj, struct drm_file *file_priv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/qxl/qxl_dumb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/qxl/qxl_dumb.c
@@ -34,6 +34,7 @@
 {
 	struct qxl_device *qdev = to_qxl(dev);
 	struct qxl_bo *qobj;
+	struct drm_gem_object *gobj;
 	uint32_t handle;
 	int r;
 	struct qxl_surface surf;
@@ -62,11 +63,13 @@
 
 	r = qxl_gem_object_create_with_handle(qdev, file_priv,
 					      QXL_GEM_DOMAIN_CPU,
-					      args->size, &surf, &qobj,
+					      args->size, &surf, &gobj,
 					      &handle);
 	if (r)
 		return r;
+	qobj = gem_to_qxl_bo(gobj);
 	qobj->is_dumb = true;
+	drm_gem_object_put(gobj);
 	args->pitch = pitch;
 	args->handle = handle;
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/qxl/qxl_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/qxl/qxl_gem.c
@@ -72,32 +72,41 @@
 	return 0;
 }
 
+/*
+ * If the caller passed a valid gobj pointer, it is responsible to call
+ * drm_gem_object_put() when it no longer needs to acess the object.
+ *
+ * If gobj is NULL, it is handled internally.
+ */
 int qxl_gem_object_create_with_handle(struct qxl_device *qdev,
 				      struct drm_file *file_priv,
 				      u32 domain,
 				      size_t size,
 				      struct qxl_surface *surf,
-				      struct qxl_bo **qobj,
+				      struct drm_gem_object **gobj,
 				      uint32_t *handle)
 {
-	struct drm_gem_object *gobj;
 	int r;
+	struct drm_gem_object *local_gobj;
 
-	BUG_ON(!qobj);
 	BUG_ON(!handle);
 
 	r = qxl_gem_object_create(qdev, size, 0,
 				  domain,
 				  false, false, surf,
-				  &gobj);
+				  &local_gobj);
 	if (r)
 		return -ENOMEM;
-	r = drm_gem_handle_create(file_priv, gobj, handle);
+	r = drm_gem_handle_create(file_priv, local_gobj, handle);
 	if (r)
 		return r;
-	/* drop reference from allocate - handle holds it now */
-	*qobj = gem_to_qxl_bo(gobj);
-	drm_gem_object_put(gobj);
+
+	if (gobj)
+		*gobj = local_gobj;
+	else
+		/* drop reference from allocate - handle holds it now */
+		drm_gem_object_put(local_gobj);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/qxl/qxl_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/qxl/qxl_ioctl.c
@@ -39,7 +39,6 @@
 	struct qxl_device *qdev = to_qxl(dev);
 	struct drm_qxl_alloc *qxl_alloc = data;
 	int ret;
-	struct qxl_bo *qobj;
 	uint32_t handle;
 	u32 domain = QXL_GEM_DOMAIN_VRAM;
 
@@ -51,7 +50,7 @@
 						domain,
 						qxl_alloc->size,
 						NULL,
-						&qobj, &handle);
+						NULL, &handle);
 	if (ret) {
 		DRM_ERROR("%s: failed to create gem ret=%d\n",
 			  __func__, ret);
@@ -393,7 +392,6 @@
 {
 	struct qxl_device *qdev = to_qxl(dev);
 	struct drm_qxl_alloc_surf *param = data;
-	struct qxl_bo *qobj;
 	int handle;
 	int ret;
 	int size, actual_stride;
@@ -413,7 +411,7 @@
 						QXL_GEM_DOMAIN_SURFACE,
 						size,
 						&surf,
-						&qobj, &handle);
+						NULL, &handle);
 	if (ret) {
 		DRM_ERROR("%s: failed to create gem ret=%d\n",
 			  __func__, ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/Kconfig
@@ -1,4 +1,4 @@
-# SPDX-License-Identifier: GPL-2.0-only
+# SPDX-License-Identifier: MIT
 config DRM_RADEON_USERPTR
 	bool "Always enable userptr support"
 	depends on DRM_RADEON
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/Makefile
@@ -1,4 +1,4 @@
-# SPDX-License-Identifier: GPL-2.0
+# SPDX-License-Identifier: MIT
 #
 # Makefile for the drm device driver.  This driver provides support for the
 # Direct Rendering Infrastructure (DRI) in XFree86 4.1.0 and higher.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/atombios.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/atombios.h
@@ -3615,7 +3615,7 @@
 {
   UCHAR ucRecordType;
   UCHAR ucFakeEDIDLength;
-  UCHAR ucFakeEDIDString[1];    // This actually has ucFakeEdidLength elements.
+  UCHAR ucFakeEDIDString[];    // This actually has ucFakeEdidLength elements.
 } ATOM_FAKE_EDID_PATCH_RECORD;
 
 typedef struct  _ATOM_PANEL_RESOLUTION_PATCH_RECORD
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/atombios_encoders.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/atombios_encoders.c
@@ -198,7 +198,8 @@
 	 * so don't register a backlight device
 	 */
 	if ((rdev->pdev->subsystem_vendor == PCI_VENDOR_ID_APPLE) &&
-	    (rdev->pdev->device == 0x6741))
+	    (rdev->pdev->device == 0x6741) &&
+	    !dmi_match(DMI_PRODUCT_NAME, "iMac12,1"))
 		return;
 
 	if (!radeon_encoder->enc_priv)
@@ -2187,11 +2188,12 @@
 
 	/*
 	 * On DCE32 any encoder can drive any block so usually just use crtc id,
-	 * but Apple thinks different at least on iMac10,1, so there use linkb,
+	 * but Apple thinks different at least on iMac10,1 and iMac11,2, so there use linkb,
 	 * otherwise the internal eDP panel will stay dark.
 	 */
 	if (ASIC_IS_DCE32(rdev)) {
-		if (dmi_match(DMI_PRODUCT_NAME, "iMac10,1"))
+		if (dmi_match(DMI_PRODUCT_NAME, "iMac10,1") ||
+		    dmi_match(DMI_PRODUCT_NAME, "iMac11,2"))
 			enc_idx = (dig->linkb) ? 1 : 0;
 		else
 			enc_idx = radeon_crtc->crtc_id;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/ci_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/ci_dpm.c
@@ -5520,6 +5520,7 @@
 	u8 frev, crev;
 	u8 *power_state_offset;
 	struct ci_ps *ps;
+	int ret;
 
 	if (!atom_parse_data_header(mode_info->atom_context, index, NULL,
 				   &frev, &crev, &data_offset))
@@ -5549,11 +5550,15 @@
 		non_clock_array_index = power_state->v2.nonClockInfoIndex;
 		non_clock_info = (struct _ATOM_PPLIB_NONCLOCK_INFO *)
 			&non_clock_info_array->nonClockInfo[non_clock_array_index];
-		if (!rdev->pm.power_state[i].clock_info)
-			return -EINVAL;
+		if (!rdev->pm.power_state[i].clock_info) {
+			ret = -EINVAL;
+			goto err_free_ps;
+		}
 		ps = kzalloc(sizeof(struct ci_ps), GFP_KERNEL);
-		if (ps == NULL)
-			return -ENOMEM;
+		if (ps == NULL) {
+			ret = -ENOMEM;
+			goto err_free_ps;
+		}
 		rdev->pm.dpm.ps[i].ps_priv = ps;
 		ci_parse_pplib_non_clock_info(rdev, &rdev->pm.dpm.ps[i],
 					      non_clock_info,
@@ -5593,6 +5598,12 @@
 	}
 
 	return 0;
+
+err_free_ps:
+	for (i = 0; i < rdev->pm.dpm.num_ps; i++)
+		kfree(rdev->pm.dpm.ps[i].ps_priv);
+	kfree(rdev->pm.dpm.ps);
+	return ret;
 }
 
 static int ci_get_vbios_boot_values(struct radeon_device *rdev,
@@ -5681,25 +5692,26 @@
 
 	ret = ci_get_vbios_boot_values(rdev, &pi->vbios_boot_state);
 	if (ret) {
-		ci_dpm_fini(rdev);
+		kfree(rdev->pm.dpm.priv);
 		return ret;
 	}
 
 	ret = r600_get_platform_caps(rdev);
 	if (ret) {
-		ci_dpm_fini(rdev);
+		kfree(rdev->pm.dpm.priv);
 		return ret;
 	}
 
 	ret = r600_parse_extended_power_table(rdev);
 	if (ret) {
-		ci_dpm_fini(rdev);
+		kfree(rdev->pm.dpm.priv);
 		return ret;
 	}
 
 	ret = ci_parse_power_table(rdev);
 	if (ret) {
-		ci_dpm_fini(rdev);
+		kfree(rdev->pm.dpm.priv);
+		r600_free_extended_power_table(rdev);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/cik.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/cik.c
@@ -9534,17 +9534,8 @@
 			u16 bridge_cfg2, gpu_cfg2;
 			u32 max_lw, current_lw, tmp;
 
-			pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-						  &bridge_cfg);
-			pcie_capability_read_word(rdev->pdev, PCI_EXP_LNKCTL,
-						  &gpu_cfg);
-
-			tmp16 = bridge_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(root, PCI_EXP_LNKCTL, tmp16);
-
-			tmp16 = gpu_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(rdev->pdev, PCI_EXP_LNKCTL,
-						   tmp16);
+			pcie_capability_set_word(root, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
+			pcie_capability_set_word(rdev->pdev, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
 
 			tmp = RREG32_PCIE_PORT(PCIE_LC_STATUS1);
 			max_lw = (tmp & LC_DETECTED_LINK_WIDTH_MASK) >> LC_DETECTED_LINK_WIDTH_SHIFT;
@@ -9591,21 +9582,14 @@
 				msleep(100);
 
 				/* linkctl */
-				pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (bridge_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(root, PCI_EXP_LNKCTL,
-							   tmp16);
-
-				pcie_capability_read_word(rdev->pdev,
-							  PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (gpu_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(rdev->pdev,
-							   PCI_EXP_LNKCTL,
-							   tmp16);
+				pcie_capability_clear_and_set_word(root, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   bridge_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
+				pcie_capability_clear_and_set_word(rdev->pdev, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   gpu_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
 
 				/* linkctl2 */
 				pcie_capability_read_word(root, PCI_EXP_LNKCTL2,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/cypress_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/cypress_dpm.c
@@ -557,8 +557,12 @@
 						     ASIC_INTERNAL_MEMORY_SS, vco_freq)) {
 			u32 reference_clock = rdev->clock.mpll.reference_freq;
 			u32 decoded_ref = rv740_get_decoded_reference_divider(dividers.ref_div);
-			u32 clk_s = reference_clock * 5 / (decoded_ref * ss.rate);
-			u32 clk_v = ss.percentage *
+			u32 clk_s, clk_v;
+
+			if (!decoded_ref)
+				return -EINVAL;
+			clk_s = reference_clock * 5 / (decoded_ref * ss.rate);
+			clk_v = ss.percentage *
 				(0x4000 * dividers.whole_fb_div + 0x800 * dividers.frac_fb_div) / (clk_s * 625);
 
 			mpll_ss1 &= ~CLKV_MASK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/evergreen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/evergreen.c
@@ -4820,14 +4820,15 @@
 			break;
 		case 44: /* hdmi */
 			afmt_idx = src_data;
-			if (!(afmt_status[afmt_idx] & AFMT_AZ_FORMAT_WTRIG))
-				DRM_DEBUG("IH: IH event w/o asserted irq bit?\n");
-
 			if (afmt_idx > 5) {
 				DRM_ERROR("Unhandled interrupt: %d %d\n",
 					  src_id, src_data);
 				break;
 			}
+
+			if (!(afmt_status[afmt_idx] & AFMT_AZ_FORMAT_WTRIG))
+				DRM_DEBUG("IH: IH event w/o asserted irq bit?\n");
+
 			afmt_status[afmt_idx] &= ~AFMT_AZ_FORMAT_WTRIG;
 			queue_hdmi = true;
 			DRM_DEBUG("IH: HDMI%d\n", afmt_idx + 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/evergreen_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/evergreen_cs.c
@@ -395,7 +395,7 @@
 	struct evergreen_cs_track *track = p->track;
 	struct eg_surface surf;
 	unsigned pitch, slice, mslice;
-	unsigned long offset;
+	u64 offset;
 	int r;
 
 	mslice = G_028C6C_SLICE_MAX(track->cb_color_view[id]) + 1;
@@ -433,14 +433,14 @@
 		return r;
 	}
 
-	offset = track->cb_color_bo_offset[id] << 8;
+	offset = (u64)track->cb_color_bo_offset[id] << 8;
 	if (offset & (surf.base_align - 1)) {
-		dev_warn(p->dev, "%s:%d cb[%d] bo base %ld not aligned with %ld\n",
+		dev_warn(p->dev, "%s:%d cb[%d] bo base %llu not aligned with %ld\n",
 			 __func__, __LINE__, id, offset, surf.base_align);
 		return -EINVAL;
 	}
 
-	offset += surf.layer_size * mslice;
+	offset += (u64)surf.layer_size * mslice;
 	if (offset > radeon_bo_size(track->cb_color_bo[id])) {
 		/* old ddx are broken they allocate bo with w*h*bpp but
 		 * program slice with ALIGN(h, 8), catch this and patch
@@ -448,14 +448,14 @@
 		 */
 		if (!surf.mode) {
 			uint32_t *ib = p->ib.ptr;
-			unsigned long tmp, nby, bsize, size, min = 0;
+			u64 tmp, nby, bsize, size, min = 0;
 
 			/* find the height the ddx wants */
 			if (surf.nby > 8) {
 				min = surf.nby - 8;
 			}
 			bsize = radeon_bo_size(track->cb_color_bo[id]);
-			tmp = track->cb_color_bo_offset[id] << 8;
+			tmp = (u64)track->cb_color_bo_offset[id] << 8;
 			for (nby = surf.nby; nby > min; nby--) {
 				size = nby * surf.nbx * surf.bpe * surf.nsamples;
 				if ((tmp + size * mslice) <= bsize) {
@@ -467,7 +467,7 @@
 				slice = ((nby * surf.nbx) / 64) - 1;
 				if (!evergreen_surface_check(p, &surf, "cb")) {
 					/* check if this one works */
-					tmp += surf.layer_size * mslice;
+					tmp += (u64)surf.layer_size * mslice;
 					if (tmp <= bsize) {
 						ib[track->cb_color_slice_idx[id]] = slice;
 						goto old_ddx_ok;
@@ -476,9 +476,9 @@
 			}
 		}
 		dev_warn(p->dev, "%s:%d cb[%d] bo too small (layer size %d, "
-			 "offset %d, max layer %d, bo size %ld, slice %d)\n",
+			 "offset %llu, max layer %d, bo size %ld, slice %d)\n",
 			 __func__, __LINE__, id, surf.layer_size,
-			track->cb_color_bo_offset[id] << 8, mslice,
+			(u64)track->cb_color_bo_offset[id] << 8, mslice,
 			radeon_bo_size(track->cb_color_bo[id]), slice);
 		dev_warn(p->dev, "%s:%d problematic surf: (%d %d) (%d %d %d %d %d %d %d)\n",
 			 __func__, __LINE__, surf.nbx, surf.nby,
@@ -562,7 +562,7 @@
 	struct evergreen_cs_track *track = p->track;
 	struct eg_surface surf;
 	unsigned pitch, slice, mslice;
-	unsigned long offset;
+	u64 offset;
 	int r;
 
 	mslice = G_028008_SLICE_MAX(track->db_depth_view) + 1;
@@ -608,18 +608,18 @@
 		return r;
 	}
 
-	offset = track->db_s_read_offset << 8;
+	offset = (u64)track->db_s_read_offset << 8;
 	if (offset & (surf.base_align - 1)) {
-		dev_warn(p->dev, "%s:%d stencil read bo base %ld not aligned with %ld\n",
+		dev_warn(p->dev, "%s:%d stencil read bo base %llu not aligned with %ld\n",
 			 __func__, __LINE__, offset, surf.base_align);
 		return -EINVAL;
 	}
-	offset += surf.layer_size * mslice;
+	offset += (u64)surf.layer_size * mslice;
 	if (offset > radeon_bo_size(track->db_s_read_bo)) {
 		dev_warn(p->dev, "%s:%d stencil read bo too small (layer size %d, "
-			 "offset %ld, max layer %d, bo size %ld)\n",
+			 "offset %llu, max layer %d, bo size %ld)\n",
 			 __func__, __LINE__, surf.layer_size,
-			(unsigned long)track->db_s_read_offset << 8, mslice,
+			(u64)track->db_s_read_offset << 8, mslice,
 			radeon_bo_size(track->db_s_read_bo));
 		dev_warn(p->dev, "%s:%d stencil invalid (0x%08x 0x%08x 0x%08x 0x%08x)\n",
 			 __func__, __LINE__, track->db_depth_size,
@@ -627,18 +627,18 @@
 		return -EINVAL;
 	}
 
-	offset = track->db_s_write_offset << 8;
+	offset = (u64)track->db_s_write_offset << 8;
 	if (offset & (surf.base_align - 1)) {
-		dev_warn(p->dev, "%s:%d stencil write bo base %ld not aligned with %ld\n",
+		dev_warn(p->dev, "%s:%d stencil write bo base %llu not aligned with %ld\n",
 			 __func__, __LINE__, offset, surf.base_align);
 		return -EINVAL;
 	}
-	offset += surf.layer_size * mslice;
+	offset += (u64)surf.layer_size * mslice;
 	if (offset > radeon_bo_size(track->db_s_write_bo)) {
 		dev_warn(p->dev, "%s:%d stencil write bo too small (layer size %d, "
-			 "offset %ld, max layer %d, bo size %ld)\n",
+			 "offset %llu, max layer %d, bo size %ld)\n",
 			 __func__, __LINE__, surf.layer_size,
-			(unsigned long)track->db_s_write_offset << 8, mslice,
+			(u64)track->db_s_write_offset << 8, mslice,
 			radeon_bo_size(track->db_s_write_bo));
 		return -EINVAL;
 	}
@@ -659,7 +659,7 @@
 	struct evergreen_cs_track *track = p->track;
 	struct eg_surface surf;
 	unsigned pitch, slice, mslice;
-	unsigned long offset;
+	u64 offset;
 	int r;
 
 	mslice = G_028008_SLICE_MAX(track->db_depth_view) + 1;
@@ -706,34 +706,34 @@
 		return r;
 	}
 
-	offset = track->db_z_read_offset << 8;
+	offset = (u64)track->db_z_read_offset << 8;
 	if (offset & (surf.base_align - 1)) {
-		dev_warn(p->dev, "%s:%d stencil read bo base %ld not aligned with %ld\n",
+		dev_warn(p->dev, "%s:%d stencil read bo base %llu not aligned with %ld\n",
 			 __func__, __LINE__, offset, surf.base_align);
 		return -EINVAL;
 	}
-	offset += surf.layer_size * mslice;
+	offset += (u64)surf.layer_size * mslice;
 	if (offset > radeon_bo_size(track->db_z_read_bo)) {
 		dev_warn(p->dev, "%s:%d depth read bo too small (layer size %d, "
-			 "offset %ld, max layer %d, bo size %ld)\n",
+			 "offset %llu, max layer %d, bo size %ld)\n",
 			 __func__, __LINE__, surf.layer_size,
-			(unsigned long)track->db_z_read_offset << 8, mslice,
+			(u64)track->db_z_read_offset << 8, mslice,
 			radeon_bo_size(track->db_z_read_bo));
 		return -EINVAL;
 	}
 
-	offset = track->db_z_write_offset << 8;
+	offset = (u64)track->db_z_write_offset << 8;
 	if (offset & (surf.base_align - 1)) {
-		dev_warn(p->dev, "%s:%d stencil write bo base %ld not aligned with %ld\n",
+		dev_warn(p->dev, "%s:%d stencil write bo base %llu not aligned with %ld\n",
 			 __func__, __LINE__, offset, surf.base_align);
 		return -EINVAL;
 	}
-	offset += surf.layer_size * mslice;
+	offset += (u64)surf.layer_size * mslice;
 	if (offset > radeon_bo_size(track->db_z_write_bo)) {
 		dev_warn(p->dev, "%s:%d depth write bo too small (layer size %d, "
-			 "offset %ld, max layer %d, bo size %ld)\n",
+			 "offset %llu, max layer %d, bo size %ld)\n",
 			 __func__, __LINE__, surf.layer_size,
-			(unsigned long)track->db_z_write_offset << 8, mslice,
+			(u64)track->db_z_write_offset << 8, mslice,
 			radeon_bo_size(track->db_z_write_bo));
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/ni.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/ni.c
@@ -813,7 +813,7 @@
 			err = 0;
 		} else if (rdev->smc_fw->size != smc_req_size) {
 			pr_err("ni_mc: Bogus length %zu in firmware \"%s\"\n",
-			       rdev->mc_fw->size, fw_name);
+			       rdev->smc_fw->size, fw_name);
 			err = -EINVAL;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/ni_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/ni_dpm.c
@@ -2241,8 +2241,12 @@
 						     ASIC_INTERNAL_MEMORY_SS, vco_freq)) {
 			u32 reference_clock = rdev->clock.mpll.reference_freq;
 			u32 decoded_ref = rv740_get_decoded_reference_divider(dividers.ref_div);
-			u32 clk_s = reference_clock * 5 / (decoded_ref * ss.rate);
-			u32 clk_v = ss.percentage *
+			u32 clk_s, clk_v;
+
+			if (!decoded_ref)
+				return -EINVAL;
+			clk_s = reference_clock * 5 / (decoded_ref * ss.rate);
+			clk_v = ss.percentage *
 				(0x4000 * dividers.whole_fb_div + 0x800 * dividers.frac_fb_div) / (clk_s * 625);
 
 			mpll_ss1 &= ~CLKV_MASK;
@@ -2741,10 +2745,10 @@
 					table->mc_reg_table_entry[k].mc_data[j] |= 0x100;
 			}
 			j++;
-			if (j > SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE)
-				return -EINVAL;
 			break;
 		case MC_SEQ_RESERVE_M >> 2:
+			if (j >= SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE)
+				return -EINVAL;
 			temp_reg = RREG32(MC_PMG_CMD_MRS1);
 			table->mc_reg_address[j].s1 = MC_PMG_CMD_MRS1 >> 2;
 			table->mc_reg_address[j].s0 = MC_SEQ_PMG_CMD_MRS1_LP >> 2;
@@ -2753,8 +2757,6 @@
 					(temp_reg & 0xffff0000) |
 					(table->mc_reg_table_entry[k].mc_data[i] & 0x0000ffff);
 			j++;
-			if (j > SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE)
-				return -EINVAL;
 			break;
 		default:
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/r100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/r100.c
@@ -1014,45 +1014,65 @@
 
 	DRM_DEBUG_KMS("\n");
 
-	if ((rdev->family == CHIP_R100) || (rdev->family == CHIP_RV100) ||
-	    (rdev->family == CHIP_RV200) || (rdev->family == CHIP_RS100) ||
-	    (rdev->family == CHIP_RS200)) {
+	switch (rdev->family) {
+	case CHIP_R100:
+	case CHIP_RV100:
+	case CHIP_RV200:
+	case CHIP_RS100:
+	case CHIP_RS200:
 		DRM_INFO("Loading R100 Microcode\n");
 		fw_name = FIRMWARE_R100;
-	} else if ((rdev->family == CHIP_R200) ||
-		   (rdev->family == CHIP_RV250) ||
-		   (rdev->family == CHIP_RV280) ||
-		   (rdev->family == CHIP_RS300)) {
+		break;
+
+	case CHIP_R200:
+	case CHIP_RV250:
+	case CHIP_RV280:
+	case CHIP_RS300:
 		DRM_INFO("Loading R200 Microcode\n");
 		fw_name = FIRMWARE_R200;
-	} else if ((rdev->family == CHIP_R300) ||
-		   (rdev->family == CHIP_R350) ||
-		   (rdev->family == CHIP_RV350) ||
-		   (rdev->family == CHIP_RV380) ||
-		   (rdev->family == CHIP_RS400) ||
-		   (rdev->family == CHIP_RS480)) {
+		break;
+
+	case CHIP_R300:
+	case CHIP_R350:
+	case CHIP_RV350:
+	case CHIP_RV380:
+	case CHIP_RS400:
+	case CHIP_RS480:
 		DRM_INFO("Loading R300 Microcode\n");
 		fw_name = FIRMWARE_R300;
-	} else if ((rdev->family == CHIP_R420) ||
-		   (rdev->family == CHIP_R423) ||
-		   (rdev->family == CHIP_RV410)) {
+		break;
+
+	case CHIP_R420:
+	case CHIP_R423:
+	case CHIP_RV410:
 		DRM_INFO("Loading R400 Microcode\n");
 		fw_name = FIRMWARE_R420;
-	} else if ((rdev->family == CHIP_RS690) ||
-		   (rdev->family == CHIP_RS740)) {
+		break;
+
+	case CHIP_RS690:
+	case CHIP_RS740:
 		DRM_INFO("Loading RS690/RS740 Microcode\n");
 		fw_name = FIRMWARE_RS690;
-	} else if (rdev->family == CHIP_RS600) {
+		break;
+
+	case CHIP_RS600:
 		DRM_INFO("Loading RS600 Microcode\n");
 		fw_name = FIRMWARE_RS600;
-	} else if ((rdev->family == CHIP_RV515) ||
-		   (rdev->family == CHIP_R520) ||
-		   (rdev->family == CHIP_RV530) ||
-		   (rdev->family == CHIP_R580) ||
-		   (rdev->family == CHIP_RV560) ||
-		   (rdev->family == CHIP_RV570)) {
+		break;
+
+	case CHIP_RV515:
+	case CHIP_R520:
+	case CHIP_RV530:
+	case CHIP_R580:
+	case CHIP_RV560:
+	case CHIP_RV570:
 		DRM_INFO("Loading R500 Microcode\n");
 		fw_name = FIRMWARE_R520;
+		break;
+
+	default:
+		DRM_ERROR("Unsupported Radeon family %u\n", rdev->family);
+		return -EINVAL;
 	}
 
 	err = request_firmware(&rdev->me_fw, fw_name, rdev->dev);
@@ -2320,7 +2340,7 @@
 	switch (prim_walk) {
 	case 1:
 		for (i = 0; i < track->num_arrays; i++) {
-			size = track->arrays[i].esize * track->max_indx * 4;
+			size = track->arrays[i].esize * track->max_indx * 4UL;
 			if (track->arrays[i].robj == NULL) {
 				DRM_ERROR("(PW %u) Vertex array %u no buffer "
 					  "bound\n", prim_walk, i);
@@ -2339,7 +2359,7 @@
 		break;
 	case 2:
 		for (i = 0; i < track->num_arrays; i++) {
-			size = track->arrays[i].esize * (nverts - 1) * 4;
+			size = track->arrays[i].esize * (nverts - 1) * 4UL;
 			if (track->arrays[i].robj == NULL) {
 				DRM_ERROR("(PW %u) Vertex array %u no buffer "
 					  "bound\n", prim_walk, i);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/r300.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/r300.c
@@ -359,7 +359,8 @@
 	return -1;
 }
 
-static void r300_gpu_init(struct radeon_device *rdev)
+/* rs400_gpu_init also calls this! */
+void r300_gpu_init(struct radeon_device *rdev)
 {
 	uint32_t gb_tile_config, tmp;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/r600_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/r600_cs.c
@@ -1277,7 +1277,7 @@
 			return -EINVAL;
 		}
 		tmp = (reg - CB_COLOR0_BASE) / 4;
-		track->cb_color_bo_offset[tmp] = radeon_get_ib_value(p, idx) << 8;
+		track->cb_color_bo_offset[tmp] = (u64)radeon_get_ib_value(p, idx) << 8;
 		ib[idx] += (u32)((reloc->gpu_offset >> 8) & 0xffffffff);
 		track->cb_color_base_last[tmp] = ib[idx];
 		track->cb_color_bo[tmp] = reloc->robj;
@@ -1304,7 +1304,7 @@
 					"0x%04X\n", reg);
 			return -EINVAL;
 		}
-		track->htile_offset = radeon_get_ib_value(p, idx) << 8;
+		track->htile_offset = (u64)radeon_get_ib_value(p, idx) << 8;
 		ib[idx] += (u32)((reloc->gpu_offset >> 8) & 0xffffffff);
 		track->htile_bo = reloc->robj;
 		track->db_dirty = true;
@@ -2106,7 +2106,7 @@
 				return -EINVAL;
 			}
 
-			offset = radeon_get_ib_value(p, idx+1) << 8;
+			offset = (u64)radeon_get_ib_value(p, idx+1) << 8;
 			if (offset != track->vgt_strmout_bo_offset[idx_value]) {
 				DRM_ERROR("bad STRMOUT_BASE_UPDATE, bo offset does not match: 0x%llx, 0x%x\n",
 					  offset, track->vgt_strmout_bo_offset[idx_value]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon.h
@@ -132,7 +132,6 @@
 /* RADEON_IB_POOL_SIZE must be a power of 2 */
 #define RADEON_IB_POOL_SIZE			16
 #define RADEON_DEBUGFS_MAX_COMPONENTS		32
-#define RADEONFB_CONN_LIMIT			4
 #define RADEON_BIOS_NUM_SCRATCH			8
 
 /* internal ring indices */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_asic.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_asic.h
@@ -165,6 +165,7 @@
  */
 extern int r300_init(struct radeon_device *rdev);
 extern void r300_fini(struct radeon_device *rdev);
+extern void r300_gpu_init(struct radeon_device *rdev);
 extern int r300_suspend(struct radeon_device *rdev);
 extern int r300_resume(struct radeon_device *rdev);
 extern int r300_asic_reset(struct radeon_device *rdev, bool hard);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_atombios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_atombios.c
@@ -1714,23 +1714,29 @@
 					fake_edid_record = (ATOM_FAKE_EDID_PATCH_RECORD *)record;
 					if (fake_edid_record->ucFakeEDIDLength) {
 						struct edid *edid;
-						int edid_size =
-							max((int)EDID_LENGTH, (int)fake_edid_record->ucFakeEDIDLength);
-						edid = kmalloc(edid_size, GFP_KERNEL);
-						if (edid) {
-							memcpy((u8 *)edid, (u8 *)&fake_edid_record->ucFakeEDIDString[0],
-							       fake_edid_record->ucFakeEDIDLength);
+						int edid_size;
 
+						if (fake_edid_record->ucFakeEDIDLength == 128)
+							edid_size = fake_edid_record->ucFakeEDIDLength;
+						else
+							edid_size = fake_edid_record->ucFakeEDIDLength * 128;
+						edid = kmemdup(&fake_edid_record->ucFakeEDIDString[0],
+							       edid_size, GFP_KERNEL);
+						if (edid) {
 							if (drm_edid_is_valid(edid)) {
 								rdev->mode_info.bios_hardcoded_edid = edid;
 								rdev->mode_info.bios_hardcoded_edid_size = edid_size;
-							} else
+							} else {
 								kfree(edid);
+							}
 						}
+						record += struct_size(fake_edid_record,
+								      ucFakeEDIDString,
+								      edid_size);
+					} else {
+						/* empty fake edid record must be 3 bytes long */
+						record += sizeof(ATOM_FAKE_EDID_PATCH_RECORD) + 1;
 					}
-					record += fake_edid_record->ucFakeEDIDLength ?
-						fake_edid_record->ucFakeEDIDLength + 2 :
-						sizeof(ATOM_FAKE_EDID_PATCH_RECORD);
 					break;
 				case LCD_PANEL_RESOLUTION_RECORD_TYPE:
 					panel_res_record = (ATOM_PANEL_RESOLUTION_PATCH_RECORD *)record;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_bios.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_bios.c
@@ -227,6 +227,7 @@
 
 	if (!found)
 		return false;
+	pci_dev_put(pdev);
 
 	rdev->bios = kmalloc(size, GFP_KERNEL);
 	if (!rdev->bios) {
@@ -612,13 +613,14 @@
 	acpi_size tbl_size;
 	UEFI_ACPI_VFCT *vfct;
 	unsigned offset;
+	bool r = false;
 
 	if (!ACPI_SUCCESS(acpi_get_table("VFCT", 1, &hdr)))
 		return false;
 	tbl_size = hdr->length;
 	if (tbl_size < sizeof(UEFI_ACPI_VFCT)) {
 		DRM_ERROR("ACPI VFCT table present but broken (too short #1)\n");
-		return false;
+		goto out;
 	}
 
 	vfct = (UEFI_ACPI_VFCT *)hdr;
@@ -631,13 +633,13 @@
 		offset += sizeof(VFCT_IMAGE_HEADER);
 		if (offset > tbl_size) {
 			DRM_ERROR("ACPI VFCT image header truncated\n");
-			return false;
+			goto out;
 		}
 
 		offset += vhdr->ImageLength;
 		if (offset > tbl_size) {
 			DRM_ERROR("ACPI VFCT image truncated\n");
-			return false;
+			goto out;
 		}
 
 		if (vhdr->ImageLength &&
@@ -649,15 +651,18 @@
 			rdev->bios = kmemdup(&vbios->VbiosContent,
 					     vhdr->ImageLength,
 					     GFP_KERNEL);
+			if (rdev->bios)
+				r = true;
 
-			if (!rdev->bios)
-				return false;
-			return true;
+			goto out;
 		}
 	}
 
 	DRM_ERROR("ACPI VFCT table present but broken (too short #2)\n");
-	return false;
+
+out:
+	acpi_put_table(hdr);
+	return r;
 }
 #else
 static inline bool radeon_acpi_vfct_bios(struct radeon_device *rdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_connectors.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_connectors.c
@@ -204,7 +204,7 @@
 
 			/* Check if bpc is within clock limit. Try to degrade gracefully otherwise */
 			if ((bpc == 12) && (mode_clock * 3/2 > max_tmds_clock)) {
-				if ((connector->display_info.edid_hdmi_dc_modes & DRM_EDID_HDMI_DC_30) &&
+				if ((connector->display_info.edid_hdmi_rgb444_dc_modes & DRM_EDID_HDMI_DC_30) &&
 					(mode_clock * 5/4 <= max_tmds_clock))
 					bpc = 10;
 				else
@@ -473,6 +473,8 @@
 	    native_mode->vdisplay != 0 &&
 	    native_mode->clock != 0) {
 		mode = drm_mode_duplicate(dev, native_mode);
+		if (!mode)
+			return NULL;
 		mode->type = DRM_MODE_TYPE_PREFERRED | DRM_MODE_TYPE_DRIVER;
 		drm_mode_set_name(mode);
 
@@ -487,6 +489,8 @@
 		 * simpler.
 		 */
 		mode = drm_cvt_mode(dev, native_mode->hdisplay, native_mode->vdisplay, 60, true, false, false);
+		if (!mode)
+			return NULL;
 		mode->type = DRM_MODE_TYPE_PREFERRED | DRM_MODE_TYPE_DRIVER;
 		DRM_DEBUG_KMS("Adding cvt approximation of native panel mode %s\n", mode->name);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_cs.c
@@ -270,7 +270,8 @@
 {
 	struct drm_radeon_cs *cs = data;
 	uint64_t *chunk_array_ptr;
-	unsigned size, i;
+	u64 size;
+	unsigned i;
 	u32 ring = RADEON_CS_RING_GFX;
 	s32 priority = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_device.c
@@ -1022,6 +1022,7 @@
 {
 	if (rdev->mode_info.atom_context) {
 		kfree(rdev->mode_info.atom_context->scratch);
+		kfree(rdev->mode_info.atom_context->iio);
 	}
 	kfree(rdev->mode_info.atom_context);
 	rdev->mode_info.atom_context = NULL;
@@ -1617,6 +1618,9 @@
 		if (r) {
 			/* delay GPU reset to resume */
 			radeon_fence_driver_force_completion(rdev, i);
+		} else {
+			/* finish executing delayed work */
+			flush_delayed_work(&rdev->fence_drv[i].lockup_work);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_display.c
@@ -677,15 +677,20 @@
 	struct radeon_device *rdev = dev->dev_private;
 	struct radeon_crtc *radeon_crtc;
 
-	radeon_crtc = kzalloc(sizeof(struct radeon_crtc) + (RADEONFB_CONN_LIMIT * sizeof(struct drm_connector *)), GFP_KERNEL);
+	radeon_crtc = kzalloc(sizeof(*radeon_crtc), GFP_KERNEL);
 	if (radeon_crtc == NULL)
 		return;
 
+	radeon_crtc->flip_queue = alloc_workqueue("radeon-crtc", WQ_HIGHPRI, 0);
+	if (!radeon_crtc->flip_queue) {
+		kfree(radeon_crtc);
+		return;
+	}
+
 	drm_crtc_init(dev, &radeon_crtc->base, &radeon_crtc_funcs);
 
 	drm_mode_crtc_set_gamma_size(&radeon_crtc->base, 256);
 	radeon_crtc->crtc_id = index;
-	radeon_crtc->flip_queue = alloc_workqueue("radeon-crtc", WQ_HIGHPRI, 0);
 	rdev->mode_info.crtcs[index] = radeon_crtc;
 
 	if (rdev->family >= CHIP_BONAIRE) {
@@ -698,12 +703,6 @@
 	dev->mode_config.cursor_width = radeon_crtc->max_cursor_width;
 	dev->mode_config.cursor_height = radeon_crtc->max_cursor_height;
 
-#if 0
-	radeon_crtc->mode_set.crtc = &radeon_crtc->base;
-	radeon_crtc->mode_set.connectors = (struct drm_connector **)(radeon_crtc + 1);
-	radeon_crtc->mode_set.num_connectors = 0;
-#endif
-
 	if (rdev->is_atom_bios && (ASIC_IS_AVIVO(rdev) || radeon_r4xx_atom))
 		radeon_atombios_init_crtc(dev, radeon_crtc);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_encoders.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_encoders.c
@@ -41,7 +41,7 @@
 	struct radeon_device *rdev = dev->dev_private;
 	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
 	struct drm_encoder *clone_encoder;
-	uint32_t index_mask = 0;
+	uint32_t index_mask = drm_encoder_mask(encoder);
 	int count;
 
 	/* DIG routing gets problematic */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_gem.c
@@ -61,7 +61,7 @@
 		goto unlock_resv;
 
 	ret = ttm_bo_vm_fault_reserved(vmf, vmf->vma->vm_page_prot,
-				       TTM_BO_VM_NUM_PREFAULT, 1);
+				       TTM_BO_VM_NUM_PREFAULT);
 	if (ret == VM_FAULT_RETRY && !(vmf->flags & FAULT_FLAG_RETRY_NOWAIT))
 		goto unlock_mclk;
 
@@ -456,7 +456,6 @@
 	struct radeon_device *rdev = dev->dev_private;
 	struct drm_radeon_gem_set_domain *args = data;
 	struct drm_gem_object *gobj;
-	struct radeon_bo *robj;
 	int r;
 
 	/* for now if someone requests domain CPU -
@@ -469,13 +468,12 @@
 		up_read(&rdev->exclusive_lock);
 		return -ENOENT;
 	}
-	robj = gem_to_radeon_bo(gobj);
 
 	r = radeon_gem_set_domain(gobj, args->read_domains, args->write_domain);
 
 	drm_gem_object_put(gobj);
 	up_read(&rdev->exclusive_lock);
-	r = radeon_gem_handle_lockup(robj->rdev, r);
+	r = radeon_gem_handle_lockup(rdev, r);
 	return r;
 }
 
@@ -655,7 +653,7 @@
 	if (r)
 		goto error_unlock;
 
-	if (bo_va->it.start)
+	if (bo_va->it.start && bo_va->bo)
 		r = radeon_vm_bo_update(rdev, bo_va, bo_va->bo->tbo.resource);
 
 error_unlock:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_kms.c
@@ -648,6 +648,8 @@
 int radeon_driver_open_kms(struct drm_device *dev, struct drm_file *file_priv)
 {
 	struct radeon_device *rdev = dev->dev_private;
+	struct radeon_fpriv *fpriv;
+	struct radeon_vm *vm;
 	int r;
 
 	file_priv->driver_priv = NULL;
@@ -660,48 +662,52 @@
 
 	/* new gpu have virtual address space support */
 	if (rdev->family >= CHIP_CAYMAN) {
-		struct radeon_fpriv *fpriv;
-		struct radeon_vm *vm;
 
 		fpriv = kzalloc(sizeof(*fpriv), GFP_KERNEL);
 		if (unlikely(!fpriv)) {
 			r = -ENOMEM;
-			goto out_suspend;
+			goto err_suspend;
 		}
 
 		if (rdev->accel_working) {
 			vm = &fpriv->vm;
 			r = radeon_vm_init(rdev, vm);
-			if (r) {
-				kfree(fpriv);
-				goto out_suspend;
-			}
+			if (r)
+				goto err_fpriv;
 
 			r = radeon_bo_reserve(rdev->ring_tmp_bo.bo, false);
-			if (r) {
-				radeon_vm_fini(rdev, vm);
-				kfree(fpriv);
-				goto out_suspend;
-			}
+			if (r)
+				goto err_vm_fini;
 
 			/* map the ib pool buffer read only into
 			 * virtual address space */
 			vm->ib_bo_va = radeon_vm_bo_add(rdev, vm,
 							rdev->ring_tmp_bo.bo);
+			if (!vm->ib_bo_va) {
+				r = -ENOMEM;
+				goto err_vm_fini;
+			}
+
 			r = radeon_vm_bo_set_addr(rdev, vm->ib_bo_va,
 						  RADEON_VA_IB_OFFSET,
 						  RADEON_VM_PAGE_READABLE |
 						  RADEON_VM_PAGE_SNOOPED);
-			if (r) {
-				radeon_vm_fini(rdev, vm);
-				kfree(fpriv);
-				goto out_suspend;
-			}
+			if (r)
+				goto err_vm_fini;
 		}
 		file_priv->driver_priv = fpriv;
 	}
 
-out_suspend:
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
+	return 0;
+
+err_vm_fini:
+	radeon_vm_fini(rdev, vm);
+err_fpriv:
+	kfree(fpriv);
+
+err_suspend:
 	pm_runtime_mark_last_busy(dev->dev);
 	pm_runtime_put_autosuspend(dev->dev);
 	return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_vce.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_vce.c
@@ -557,7 +557,7 @@
 {
 	int session_idx = -1;
 	bool destroyed = false, created = false, allocated = false;
-	uint32_t tmp, handle = 0;
+	uint32_t tmp = 0, handle = 0;
 	uint32_t *size = &tmp;
 	int i, r = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/radeon_vm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/radeon_vm.c
@@ -1204,13 +1204,17 @@
 	r = radeon_bo_create(rdev, pd_size, align, true,
 			     RADEON_GEM_DOMAIN_VRAM, 0, NULL,
 			     NULL, &vm->page_directory);
-	if (r)
+	if (r) {
+		kfree(vm->page_tables);
+		vm->page_tables = NULL;
 		return r;
-
+	}
 	r = radeon_vm_clear_bo(rdev, vm->page_directory);
 	if (r) {
 		radeon_bo_unref(&vm->page_directory);
 		vm->page_directory = NULL;
+		kfree(vm->page_tables);
+		vm->page_tables = NULL;
 		return r;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/rs400.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/rs400.c
@@ -255,8 +255,22 @@
 
 static void rs400_gpu_init(struct radeon_device *rdev)
 {
-	/* FIXME: is this correct ? */
-	r420_pipes_init(rdev);
+	/* Earlier code was calling r420_pipes_init and then
+	 * rs400_mc_wait_for_idle(rdev). The problem is that
+	 * at least on my Mobility Radeon Xpress 200M RC410 card
+	 * that ends up in this code path ends up num_gb_pipes == 3
+	 * while the card seems to have only one pipe. With the
+	 * r420 pipe initialization method.
+	 *
+	 * Problems shown up as HyperZ glitches, see:
+	 * https://bugs.freedesktop.org/show_bug.cgi?id=110897
+	 *
+	 * Delegating initialization to r300 code seems to work
+	 * and results in proper pipe numbers. The rs400 cards
+	 * are said to be not r400, but r300 kind of cards.
+	 */
+	r300_gpu_init(rdev);
+
 	if (rs400_mc_wait_for_idle(rdev)) {
 		pr_warn("rs400: Failed to wait MC idle while programming pipes. Bad things might happen. %08x\n",
 			RREG32(RADEON_MC_STATUS));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/rv740_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/rv740_dpm.c
@@ -249,8 +249,12 @@
 						     ASIC_INTERNAL_MEMORY_SS, vco_freq)) {
 			u32 reference_clock = rdev->clock.mpll.reference_freq;
 			u32 decoded_ref = rv740_get_decoded_reference_divider(dividers.ref_div);
-			u32 clk_s = reference_clock * 5 / (decoded_ref * ss.rate);
-			u32 clk_v = 0x40000 * ss.percentage *
+			u32 clk_s, clk_v;
+
+			if (!decoded_ref)
+				return -EINVAL;
+			clk_s = reference_clock * 5 / (decoded_ref * ss.rate);
+			clk_v = 0x40000 * ss.percentage *
 				(dividers.whole_fb_div + (dividers.frac_fb_div / 8)) / (clk_s * 10000);
 
 			mpll_ss1 &= ~CLKV_MASK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/si.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/si.c
@@ -3611,6 +3611,10 @@
 	for (i = RADEON_RING_TYPE_GFX_INDEX; i <= CAYMAN_RING_TYPE_CP2_INDEX; ++i) {
 		ring = &rdev->ring[i];
 		r = radeon_ring_lock(rdev, ring, 2);
+		if (r) {
+			DRM_ERROR("radeon: cp failed to lock ring (%d).\n", r);
+			return r;
+		}
 
 		/* clear the compute context state */
 		radeon_ring_write(ring, PACKET3_COMPUTE(PACKET3_CLEAR_STATE, 0));
@@ -7131,17 +7135,8 @@
 			u16 bridge_cfg2, gpu_cfg2;
 			u32 max_lw, current_lw, tmp;
 
-			pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-						  &bridge_cfg);
-			pcie_capability_read_word(rdev->pdev, PCI_EXP_LNKCTL,
-						  &gpu_cfg);
-
-			tmp16 = bridge_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(root, PCI_EXP_LNKCTL, tmp16);
-
-			tmp16 = gpu_cfg | PCI_EXP_LNKCTL_HAWD;
-			pcie_capability_write_word(rdev->pdev, PCI_EXP_LNKCTL,
-						   tmp16);
+			pcie_capability_set_word(root, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
+			pcie_capability_set_word(rdev->pdev, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_HAWD);
 
 			tmp = RREG32_PCIE(PCIE_LC_STATUS1);
 			max_lw = (tmp & LC_DETECTED_LINK_WIDTH_MASK) >> LC_DETECTED_LINK_WIDTH_SHIFT;
@@ -7188,22 +7183,14 @@
 				msleep(100);
 
 				/* linkctl */
-				pcie_capability_read_word(root, PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (bridge_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(root,
-							   PCI_EXP_LNKCTL,
-							   tmp16);
-
-				pcie_capability_read_word(rdev->pdev,
-							  PCI_EXP_LNKCTL,
-							  &tmp16);
-				tmp16 &= ~PCI_EXP_LNKCTL_HAWD;
-				tmp16 |= (gpu_cfg & PCI_EXP_LNKCTL_HAWD);
-				pcie_capability_write_word(rdev->pdev,
-							   PCI_EXP_LNKCTL,
-							   tmp16);
+				pcie_capability_clear_and_set_word(root, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   bridge_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
+				pcie_capability_clear_and_set_word(rdev->pdev, PCI_EXP_LNKCTL,
+								   PCI_EXP_LNKCTL_HAWD,
+								   gpu_cfg &
+								   PCI_EXP_LNKCTL_HAWD);
 
 				/* linkctl2 */
 				pcie_capability_read_word(root, PCI_EXP_LNKCTL2,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/sumo_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/sumo_dpm.c
@@ -1493,8 +1493,10 @@
 		non_clock_array_index = power_state->v2.nonClockInfoIndex;
 		non_clock_info = (struct _ATOM_PPLIB_NONCLOCK_INFO *)
 			&non_clock_info_array->nonClockInfo[non_clock_array_index];
-		if (!rdev->pm.power_state[i].clock_info)
+		if (!rdev->pm.power_state[i].clock_info) {
+			kfree(rdev->pm.dpm.ps);
 			return -EINVAL;
+		}
 		ps = kzalloc(sizeof(struct sumo_ps), GFP_KERNEL);
 		if (ps == NULL) {
 			kfree(rdev->pm.dpm.ps);
@@ -1619,6 +1621,8 @@
 
 	for (i = 0; i < SUMO_MAX_HARDWARE_POWERLEVELS; i++) {
 		if (table[i].ulSupportedSCLK != 0) {
+			if (table[i].usVoltageIndex >= SUMO_MAX_NUMBER_VOLTAGES)
+				continue;
 			vid_mapping_table->entries[table[i].usVoltageIndex].vid_7bit =
 				table[i].usVoltageID;
 			vid_mapping_table->entries[table[i].usVoltageIndex].vid_2bit =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/radeon/trinity_dpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/radeon/trinity_dpm.c
@@ -1726,8 +1726,10 @@
 		non_clock_array_index = power_state->v2.nonClockInfoIndex;
 		non_clock_info = (struct _ATOM_PPLIB_NONCLOCK_INFO *)
 			&non_clock_info_array->nonClockInfo[non_clock_array_index];
-		if (!rdev->pm.power_state[i].clock_info)
+		if (!rdev->pm.power_state[i].clock_info) {
+			kfree(rdev->pm.dpm.ps);
 			return -EINVAL;
+		}
 		ps = kzalloc(sizeof(struct sumo_ps), GFP_KERNEL);
 		if (ps == NULL) {
 			kfree(rdev->pm.dpm.ps);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rcar-du/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rcar-du/Kconfig
@@ -4,8 +4,6 @@
 	depends on DRM && OF
 	depends on ARM || ARM64
 	depends on ARCH_RENESAS || COMPILE_TEST
-	imply DRM_RCAR_CMM
-	imply DRM_RCAR_LVDS
 	select DRM_KMS_HELPER
 	select DRM_KMS_CMA_HELPER
 	select DRM_GEM_CMA_HELPER
@@ -14,13 +12,17 @@
 	  Choose this option if you have an R-Car chipset.
 	  If M is selected the module will be called rcar-du-drm.
 
-config DRM_RCAR_CMM
-	tristate "R-Car DU Color Management Module (CMM) Support"
-	depends on DRM && OF
+config DRM_RCAR_USE_CMM
+	bool "R-Car DU Color Management Module (CMM) Support"
 	depends on DRM_RCAR_DU
+	default DRM_RCAR_DU
 	help
 	  Enable support for R-Car Color Management Module (CMM).
 
+config DRM_RCAR_CMM
+	def_tristate DRM_RCAR_DU
+	depends on DRM_RCAR_USE_CMM
+
 config DRM_RCAR_DW_HDMI
 	tristate "R-Car Gen3 and RZ/G2 DU HDMI Encoder Support"
 	depends on DRM && OF
@@ -28,15 +30,20 @@
 	help
 	  Enable support for R-Car Gen3 or RZ/G2 internal HDMI encoder.
 
+config DRM_RCAR_USE_LVDS
+	bool "R-Car DU LVDS Encoder Support"
+	depends on DRM_BRIDGE && OF
+	default DRM_RCAR_DU
+	help
+	  Enable support for the R-Car Display Unit embedded LVDS encoders.
+
 config DRM_RCAR_LVDS
-	tristate "R-Car DU LVDS Encoder Support"
-	depends on DRM && DRM_BRIDGE && OF
+	def_tristate DRM_RCAR_DU
+	depends on DRM_RCAR_USE_LVDS
 	select DRM_KMS_HELPER
 	select DRM_PANEL
 	select OF_FLATTREE
 	select OF_OVERLAY
-	help
-	  Enable support for the R-Car Display Unit embedded LVDS encoders.
 
 config DRM_RCAR_VSP
 	bool "R-Car DU VSP Compositor Support" if ARM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -215,6 +215,7 @@
 	const struct drm_display_mode *mode = &rcrtc->crtc.state->adjusted_mode;
 	struct rcar_du_device *rcdu = rcrtc->dev;
 	unsigned long mode_clock = mode->clock * 1000;
+	unsigned int hdse_offset;
 	u32 dsmr;
 	u32 escr;
 
@@ -298,10 +299,15 @@
 	     | DSMR_DIPM_DISP | DSMR_CSPM;
 	rcar_du_crtc_write(rcrtc, DSMR, dsmr);
 
+	hdse_offset = 19;
+	if (rcrtc->group->cmms_mask & BIT(rcrtc->index % 2))
+		hdse_offset += 25;
+
 	/* Display timings */
-	rcar_du_crtc_write(rcrtc, HDSR, mode->htotal - mode->hsync_start - 19);
+	rcar_du_crtc_write(rcrtc, HDSR, mode->htotal - mode->hsync_start -
+					hdse_offset);
 	rcar_du_crtc_write(rcrtc, HDER, mode->htotal - mode->hsync_start +
-					mode->hdisplay - 19);
+					mode->hdisplay - hdse_offset);
 	rcar_du_crtc_write(rcrtc, HSWR, mode->hsync_end -
 					mode->hsync_start - 1);
 	rcar_du_crtc_write(rcrtc, HCR,  mode->htotal - 1);
@@ -836,6 +842,7 @@
 	struct rcar_du_crtc *rcrtc = to_rcar_crtc(crtc);
 	struct rcar_du_device *rcdu = rcrtc->dev;
 	bool interlaced = mode->flags & DRM_MODE_FLAG_INTERLACE;
+	unsigned int min_sync_porch;
 	unsigned int vbp;
 
 	if (interlaced && !rcar_du_has(rcdu, RCAR_DU_FEATURE_INTERLACED))
@@ -843,9 +850,14 @@
 
 	/*
 	 * The hardware requires a minimum combined horizontal sync and back
-	 * porch of 20 pixels and a minimum vertical back porch of 3 lines.
+	 * porch of 20 pixels (when CMM isn't used) or 45 pixels (when CMM is
+	 * used), and a minimum vertical back porch of 3 lines.
 	 */
-	if (mode->htotal - mode->hsync_start < 20)
+	min_sync_porch = 20;
+	if (rcrtc->group->cmms_mask & BIT(rcrtc->index % 2))
+		min_sync_porch += 25;
+
+	if (mode->htotal - mode->hsync_start < min_sync_porch)
 		return MODE_HBLANK_NARROW;
 
 	vbp = (mode->vtotal - mode->vsync_end) / (interlaced ? 2 : 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rcar-du/rcar_du_encoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rcar-du/rcar_du_encoder.c
@@ -109,8 +109,8 @@
 	renc = drmm_encoder_alloc(&rcdu->ddev, struct rcar_du_encoder, base,
 				  &rcar_du_encoder_funcs, DRM_MODE_ENCODER_NONE,
 				  NULL);
-	if (!renc)
-		return -ENOMEM;
+	if (IS_ERR(renc))
+		return PTR_ERR(renc);
 
 	renc->output = output;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -398,7 +398,15 @@
 	if (IS_ERR(dp->adp))
 		return PTR_ERR(dp->adp);
 
-	return component_add(dev, &rockchip_dp_component_ops);
+	ret = component_add(dev, &rockchip_dp_component_ops);
+	if (ret)
+		goto err_dp_remove;
+
+	return 0;
+
+err_dp_remove:
+	analogix_dp_remove(dp->adp);
+	return ret;
 }
 
 static int rockchip_dp_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -277,8 +277,9 @@
 	return ret;
 }
 
-static int cdn_dp_connector_mode_valid(struct drm_connector *connector,
-				       struct drm_display_mode *mode)
+static enum drm_mode_status
+cdn_dp_connector_mode_valid(struct drm_connector *connector,
+			    struct drm_display_mode *mode)
 {
 	struct cdn_dp_device *dp = connector_to_dp(connector);
 	struct drm_display_info *display_info = &dp->connector.display_info;
@@ -564,7 +565,7 @@
 	video->v_sync_polarity = !!(mode->flags & DRM_MODE_FLAG_NVSYNC);
 	video->h_sync_polarity = !!(mode->flags & DRM_MODE_FLAG_NHSYNC);
 
-	memcpy(&dp->mode, adjusted, sizeof(*mode));
+	drm_mode_copy(&dp->mode, adjusted);
 }
 
 static bool cdn_dp_check_link_status(struct cdn_dp_device *dp)
@@ -915,9 +916,6 @@
 {
 	struct cdn_dp_device *dp = container_of(work, struct cdn_dp_device,
 						event_work);
-	struct drm_connector *connector = &dp->connector;
-	enum drm_connector_status old_status;
-
 	int ret;
 
 	mutex_lock(&dp->lock);
@@ -979,11 +977,7 @@
 
 out:
 	mutex_unlock(&dp->lock);
-
-	old_status = connector->status;
-	connector->status = connector->funcs->detect(connector, false);
-	if (old_status != connector->status)
-		drm_kms_helper_hotplug_event(dp->drm_dev);
+	drm_connector_helper_hpd_irq_event(&dp->connector);
 }
 
 static int cdn_dp_pd_event(struct notifier_block *nb,
@@ -1145,6 +1139,7 @@
 	struct cdn_dp_device *dp;
 	struct extcon_dev *extcon;
 	struct phy *phy;
+	int ret;
 	int i;
 
 	dp = devm_kzalloc(dev, sizeof(*dp), GFP_KERNEL);
@@ -1185,9 +1180,19 @@
 	mutex_init(&dp->lock);
 	dev_set_drvdata(dev, dp);
 
-	cdn_dp_audio_codec_init(dp, dev);
+	ret = cdn_dp_audio_codec_init(dp, dev);
+	if (ret)
+		return ret;
 
-	return component_add(dev, &cdn_dp_component_ops);
+	ret = component_add(dev, &cdn_dp_component_ops);
+	if (ret)
+		goto err_audio_deinit;
+
+	return 0;
+
+err_audio_deinit:
+	platform_device_unregister(dp->audio_pdev);
+	return ret;
 }
 
 static int cdn_dp_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c
@@ -268,6 +268,8 @@
 	struct dw_mipi_dsi *dmd;
 	const struct rockchip_dw_dsi_chip_data *cdata;
 	struct dw_mipi_dsi_plat_data pdata;
+
+	bool dsi_bound;
 };
 
 struct dphy_pll_parameter_map {
@@ -773,10 +775,6 @@
 	if (mux < 0)
 		return;
 
-	pm_runtime_get_sync(dsi->dev);
-	if (dsi->slave)
-		pm_runtime_get_sync(dsi->slave->dev);
-
 	/*
 	 * For the RK3399, the clk of grf must be enabled before writing grf
 	 * register. And for RK3288 or other soc, this grf_clk must be NULL,
@@ -795,20 +793,10 @@
 	clk_disable_unprepare(dsi->grf_clk);
 }
 
-static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
-{
-	struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder);
-
-	if (dsi->slave)
-		pm_runtime_put(dsi->slave->dev);
-	pm_runtime_put(dsi->dev);
-}
-
 static const struct drm_encoder_helper_funcs
 dw_mipi_dsi_encoder_helper_funcs = {
 	.atomic_check = dw_mipi_dsi_encoder_atomic_check,
 	.enable = dw_mipi_dsi_encoder_enable,
-	.disable = dw_mipi_dsi_encoder_disable,
 };
 
 static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi,
@@ -938,10 +926,14 @@
 		put_device(second);
 	}
 
+	pm_runtime_get_sync(dsi->dev);
+	if (dsi->slave)
+		pm_runtime_get_sync(dsi->slave->dev);
+
 	ret = clk_prepare_enable(dsi->pllref_clk);
 	if (ret) {
 		DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret);
-		return ret;
+		goto out_pm_runtime;
 	}
 
 	/*
@@ -953,7 +945,7 @@
 	ret = clk_prepare_enable(dsi->grf_clk);
 	if (ret) {
 		DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret);
-		return ret;
+		goto out_pll_clk;
 	}
 
 	dw_mipi_dsi_rockchip_config(dsi);
@@ -965,16 +957,27 @@
 	ret = rockchip_dsi_drm_create_encoder(dsi, drm_dev);
 	if (ret) {
 		DRM_DEV_ERROR(dev, "Failed to create drm encoder\n");
-		return ret;
+		goto out_pll_clk;
 	}
 
 	ret = dw_mipi_dsi_bind(dsi->dmd, &dsi->encoder);
 	if (ret) {
 		DRM_DEV_ERROR(dev, "Failed to bind: %d\n", ret);
-		return ret;
+		goto out_pll_clk;
 	}
 
+	dsi->dsi_bound = true;
+
 	return 0;
+
+out_pll_clk:
+	clk_disable_unprepare(dsi->pllref_clk);
+out_pm_runtime:
+	pm_runtime_put(dsi->dev);
+	if (dsi->slave)
+		pm_runtime_put(dsi->slave->dev);
+
+	return ret;
 }
 
 static void dw_mipi_dsi_rockchip_unbind(struct device *dev,
@@ -986,9 +989,15 @@
 	if (dsi->is_slave)
 		return;
 
+	dsi->dsi_bound = false;
+
 	dw_mipi_dsi_unbind(dsi->dmd);
 
 	clk_disable_unprepare(dsi->pllref_clk);
+
+	pm_runtime_put(dsi->dev);
+	if (dsi->slave)
+		pm_runtime_put(dsi->slave->dev);
 }
 
 static const struct component_ops dw_mipi_dsi_rockchip_ops = {
@@ -1018,23 +1027,31 @@
 	if (ret) {
 		DRM_DEV_ERROR(dsi->dev, "Failed to register component: %d\n",
 					ret);
-		return ret;
+		goto out;
 	}
 
 	second = dw_mipi_dsi_rockchip_find_second(dsi);
-	if (IS_ERR(second))
-		return PTR_ERR(second);
+	if (IS_ERR(second)) {
+		ret = PTR_ERR(second);
+		goto out;
+	}
 	if (second) {
 		ret = component_add(second, &dw_mipi_dsi_rockchip_ops);
 		if (ret) {
 			DRM_DEV_ERROR(second,
 				      "Failed to register component: %d\n",
 				      ret);
-			return ret;
+			goto out;
 		}
 	}
 
 	return 0;
+
+out:
+	mutex_lock(&dsi->usage_mutex);
+	dsi->usage_mode = DW_DSI_USAGE_IDLE;
+	mutex_unlock(&dsi->usage_mutex);
+	return ret;
 }
 
 static int dw_mipi_dsi_rockchip_host_detach(void *priv_data,
@@ -1276,6 +1293,36 @@
 	.exit		= dw_mipi_dsi_dphy_exit,
 };
 
+static int __maybe_unused dw_mipi_dsi_rockchip_resume(struct device *dev)
+{
+	struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev);
+	int ret;
+
+	/*
+	 * Re-configure DSI state, if we were previously initialized. We need
+	 * to do this before rockchip_drm_drv tries to re-enable() any panels.
+	 */
+	if (dsi->dsi_bound) {
+		ret = clk_prepare_enable(dsi->grf_clk);
+		if (ret) {
+			DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret);
+			return ret;
+		}
+
+		dw_mipi_dsi_rockchip_config(dsi);
+		if (dsi->slave)
+			dw_mipi_dsi_rockchip_config(dsi->slave);
+
+		clk_disable_unprepare(dsi->grf_clk);
+	}
+
+	return 0;
+}
+
+static const struct dev_pm_ops dw_mipi_dsi_rockchip_pm_ops = {
+	SET_LATE_SYSTEM_SLEEP_PM_OPS(NULL, dw_mipi_dsi_rockchip_resume)
+};
+
 static int dw_mipi_dsi_rockchip_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -1397,14 +1444,10 @@
 		if (ret != -EPROBE_DEFER)
 			DRM_DEV_ERROR(dev,
 				      "Failed to probe dw_mipi_dsi: %d\n", ret);
-		goto err_clkdisable;
+		return ret;
 	}
 
 	return 0;
-
-err_clkdisable:
-	clk_disable_unprepare(dsi->pllref_clk);
-	return ret;
 }
 
 static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev)
@@ -1593,6 +1636,13 @@
 	.remove		= dw_mipi_dsi_rockchip_remove,
 	.driver		= {
 		.of_match_table = dw_mipi_dsi_rockchip_dt_ids,
+		.pm	= &dw_mipi_dsi_rockchip_pm_ops,
 		.name	= "dw-mipi-dsi-rockchip",
+		/*
+		 * For dual-DSI display, one DSI pokes at the other DSI's
+		 * drvdata in dw_mipi_dsi_rockchip_find_second(). This is not
+		 * safe for asynchronous probe.
+		 */
+		.probe_type = PROBE_FORCE_SYNCHRONOUS,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c
@@ -389,6 +389,8 @@
 		HIWORD_UPDATE(RK3328_HDMI_SDAIN_MSK | RK3328_HDMI_SCLIN_MSK,
 			      RK3328_HDMI_SDAIN_MSK | RK3328_HDMI_SCLIN_MSK |
 			      RK3328_HDMI_HPD_IOE));
+
+	dw_hdmi_rk3328_read_hpd(dw_hdmi, data);
 }
 
 static const struct dw_hdmi_phy_ops rk3228_hdmi_phy_ops = {
@@ -529,13 +531,6 @@
 		return ret;
 	}
 
-	ret = clk_prepare_enable(hdmi->vpll_clk);
-	if (ret) {
-		DRM_DEV_ERROR(hdmi->dev, "Failed to enable HDMI vpll: %d\n",
-			      ret);
-		return ret;
-	}
-
 	hdmi->phy = devm_phy_optional_get(dev, "hdmi");
 	if (IS_ERR(hdmi->phy)) {
 		ret = PTR_ERR(hdmi->phy);
@@ -544,6 +539,13 @@
 		return ret;
 	}
 
+	ret = clk_prepare_enable(hdmi->vpll_clk);
+	if (ret) {
+		DRM_DEV_ERROR(hdmi->dev, "Failed to enable HDMI vpll: %d\n",
+			      ret);
+		return ret;
+	}
+
 	drm_encoder_helper_add(encoder, &dw_hdmi_rockchip_encoder_helper_funcs);
 	drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/inno_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/inno_hdmi.c
@@ -402,7 +402,7 @@
 	hdmi_writeb(hdmi, HDMI_VIDEO_EXT_HBLANK_L, value & 0xFF);
 	hdmi_writeb(hdmi, HDMI_VIDEO_EXT_HBLANK_H, (value >> 8) & 0xFF);
 
-	value = mode->hsync_start - mode->hdisplay;
+	value = mode->htotal - mode->hsync_start;
 	hdmi_writeb(hdmi, HDMI_VIDEO_EXT_HDELAY_L, value & 0xFF);
 	hdmi_writeb(hdmi, HDMI_VIDEO_EXT_HDELAY_H, (value >> 8) & 0xFF);
 
@@ -417,7 +417,7 @@
 	value = mode->vtotal - mode->vdisplay;
 	hdmi_writeb(hdmi, HDMI_VIDEO_EXT_VBLANK, value & 0xFF);
 
-	value = mode->vsync_start - mode->vdisplay;
+	value = mode->vtotal - mode->vsync_start;
 	hdmi_writeb(hdmi, HDMI_VIDEO_EXT_VDELAY, value & 0xFF);
 
 	value = mode->vsync_end - mode->vsync_start;
@@ -488,7 +488,7 @@
 	inno_hdmi_setup(hdmi, adj_mode);
 
 	/* Store the display mode for plugin/DPMS poweron events */
-	memcpy(&hdmi->previous_mode, adj_mode, sizeof(hdmi->previous_mode));
+	drm_mode_copy(&hdmi->previous_mode, adj_mode);
 }
 
 static void inno_hdmi_encoder_enable(struct drm_encoder *encoder)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rk3066_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rk3066_hdmi.c
@@ -383,7 +383,7 @@
 	struct rk3066_hdmi *hdmi = to_rk3066_hdmi(encoder);
 
 	/* Store the display mode for plugin/DPMS poweron events. */
-	memcpy(&hdmi->previous_mode, adj_mode, sizeof(hdmi->previous_mode));
+	drm_mode_copy(&hdmi->previous_mode, adj_mode);
 }
 
 static void rk3066_hdmi_encoder_enable(struct drm_encoder *encoder)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rockchip_drm_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rockchip_drm_gem.c
@@ -39,7 +39,7 @@
 
 	ret = iommu_map_sgtable(private->domain, rk_obj->dma_addr, rk_obj->sgt,
 				prot);
-	if (ret < rk_obj->base.size) {
+	if (ret < (ssize_t)rk_obj->base.size) {
 		DRM_ERROR("failed to map buffer: size=%zd request_size=%zd\n",
 			  ret, rk_obj->base.size);
 		ret = -ENOMEM;
@@ -251,9 +251,6 @@
 	else
 		ret = rockchip_drm_gem_object_mmap_dma(obj, vma);
 
-	if (ret)
-		drm_gem_vm_close(vma);
-
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -9,6 +9,7 @@
 #include <linux/delay.h>
 #include <linux/iopoll.h>
 #include <linux/kernel.h>
+#include <linux/log2.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
@@ -66,6 +67,9 @@
 #define VOP_REG_SET(vop, group, name, v) \
 		    vop_reg_set(vop, &vop->data->group->name, 0, ~0, v, #name)
 
+#define VOP_HAS_REG(vop, group, name) \
+		(!!(vop->data->group->name.mask))
+
 #define VOP_INTR_SET_TYPE(vop, name, type, v) \
 	do { \
 		int i, reg = 0, mask = 0; \
@@ -249,14 +253,22 @@
 	VOP_REG_SET(vop, common, cfg_done, 1);
 }
 
-static bool has_rb_swapped(uint32_t format)
+static bool has_rb_swapped(uint32_t version, uint32_t format)
 {
 	switch (format) {
 	case DRM_FORMAT_XBGR8888:
 	case DRM_FORMAT_ABGR8888:
-	case DRM_FORMAT_BGR888:
 	case DRM_FORMAT_BGR565:
 		return true;
+	/*
+	 * full framework (IP version 3.x) only need rb swapped for RGB888 and
+	 * little framework (IP version 2.x) only need rb swapped for BGR888,
+	 * check for 3.x to also only rb swap BGR888 for unknown vop version
+	 */
+	case DRM_FORMAT_RGB888:
+		return VOP_MAJOR(version) == 3;
+	case DRM_FORMAT_BGR888:
+		return VOP_MAJOR(version) != 3;
 	default:
 		return false;
 	}
@@ -363,8 +375,8 @@
 	if (info->is_yuv)
 		is_yuv = true;
 
-	if (dst_w > 3840) {
-		DRM_DEV_ERROR(vop->dev, "Maximum dst width (3840) exceeded\n");
+	if (dst_w > 4096) {
+		DRM_DEV_ERROR(vop->dev, "Maximum dst width (4096) exceeded\n");
 		return;
 	}
 
@@ -703,13 +715,13 @@
 	if (crtc->state->self_refresh_active)
 		rockchip_drm_set_win_enabled(crtc, false);
 
+	if (crtc->state->self_refresh_active)
+		goto out;
+
 	mutex_lock(&vop->vop_lock);
 
 	drm_crtc_vblank_off(crtc);
 
-	if (crtc->state->self_refresh_active)
-		goto out;
-
 	/*
 	 * Vop standby will take effect at end of current frame,
 	 * if dsp hold valid irq happen, it means standby complete.
@@ -741,9 +753,9 @@
 	vop_core_clks_disable(vop);
 	pm_runtime_put(vop->dev);
 
-out:
 	mutex_unlock(&vop->vop_lock);
 
+out:
 	if (crtc->state->event && !crtc->state->active) {
 		spin_lock_irq(&crtc->dev->event_lock);
 		drm_crtc_send_vblank_event(crtc, crtc->state->event);
@@ -820,12 +832,12 @@
 	 * need align with 2 pixel.
 	 */
 	if (fb->format->is_yuv && ((new_plane_state->src.x1 >> 16) % 2)) {
-		DRM_ERROR("Invalid Source: Yuv format not support odd xpos\n");
+		DRM_DEBUG_KMS("Invalid Source: Yuv format not support odd xpos\n");
 		return -EINVAL;
 	}
 
 	if (fb->format->is_yuv && new_plane_state->rotation & DRM_MODE_REFLECT_Y) {
-		DRM_ERROR("Invalid Source: Yuv format does not support this rotation\n");
+		DRM_DEBUG_KMS("Invalid Source: Yuv format does not support this rotation\n");
 		return -EINVAL;
 	}
 
@@ -833,7 +845,7 @@
 		struct vop *vop = to_vop(crtc);
 
 		if (!vop->data->afbc) {
-			DRM_ERROR("vop does not support AFBC\n");
+			DRM_DEBUG_KMS("vop does not support AFBC\n");
 			return -EINVAL;
 		}
 
@@ -842,15 +854,16 @@
 			return ret;
 
 		if (new_plane_state->src.x1 || new_plane_state->src.y1) {
-			DRM_ERROR("AFBC does not support offset display, xpos=%d, ypos=%d, offset=%d\n",
-				  new_plane_state->src.x1,
-				  new_plane_state->src.y1, fb->offsets[0]);
+			DRM_DEBUG_KMS("AFBC does not support offset display, " \
+				      "xpos=%d, ypos=%d, offset=%d\n",
+				      new_plane_state->src.x1, new_plane_state->src.y1,
+				      fb->offsets[0]);
 			return -EINVAL;
 		}
 
 		if (new_plane_state->rotation && new_plane_state->rotation != DRM_MODE_ROTATE_0) {
-			DRM_ERROR("No rotation support in AFBC, rotation=%d\n",
-				  new_plane_state->rotation);
+			DRM_DEBUG_KMS("No rotation support in AFBC, rotation=%d\n",
+				      new_plane_state->rotation);
 			return -EINVAL;
 		}
 	}
@@ -997,7 +1010,7 @@
 	VOP_WIN_SET(vop, win, dsp_info, dsp_info);
 	VOP_WIN_SET(vop, win, dsp_st, dsp_st);
 
-	rb_swap = has_rb_swapped(fb->format->format);
+	rb_swap = has_rb_swapped(vop->data->version, fb->format->format);
 	VOP_WIN_SET(vop, win, rb_swap, rb_swap);
 
 	/*
@@ -1052,10 +1065,10 @@
 	if (!plane->state->fb)
 		return -EINVAL;
 
-	if (state)
-		crtc_state = drm_atomic_get_existing_crtc_state(state,
-								new_plane_state->crtc);
-	else /* Special case for asynchronous cursor updates. */
+	crtc_state = drm_atomic_get_existing_crtc_state(state, new_plane_state->crtc);
+
+	/* Special case for asynchronous cursor updates. */
+	if (!crtc_state)
 		crtc_state = plane->crtc->state;
 
 	return drm_atomic_helper_check_plane_state(plane->state, crtc_state,
@@ -1202,17 +1215,22 @@
 	return vop_read_reg(vop, 0, &vop->data->common->dsp_lut_en);
 }
 
+static u32 vop_lut_buffer_index(struct vop *vop)
+{
+	return vop_read_reg(vop, 0, &vop->data->common->lut_buffer_index);
+}
+
 static void vop_crtc_write_gamma_lut(struct vop *vop, struct drm_crtc *crtc)
 {
 	struct drm_color_lut *lut = crtc->state->gamma_lut->data;
-	unsigned int i;
+	unsigned int i, bpc = ilog2(vop->data->lut_size);
 
 	for (i = 0; i < crtc->gamma_size; i++) {
 		u32 word;
 
-		word = (drm_color_lut_extract(lut[i].red, 10) << 20) |
-		       (drm_color_lut_extract(lut[i].green, 10) << 10) |
-			drm_color_lut_extract(lut[i].blue, 10);
+		word = (drm_color_lut_extract(lut[i].red, bpc) << (2 * bpc)) |
+		       (drm_color_lut_extract(lut[i].green, bpc) << bpc) |
+			drm_color_lut_extract(lut[i].blue, bpc);
 		writel(word, vop->lut_regs + i * 4);
 	}
 }
@@ -1222,38 +1240,66 @@
 {
 	struct drm_crtc_state *state = crtc->state;
 	unsigned int idle;
+	u32 lut_idx, old_idx;
 	int ret;
 
 	if (!vop->lut_regs)
 		return;
-	/*
-	 * To disable gamma (gamma_lut is null) or to write
-	 * an update to the LUT, clear dsp_lut_en.
-	 */
-	spin_lock(&vop->reg_lock);
-	VOP_REG_SET(vop, common, dsp_lut_en, 0);
-	vop_cfg_done(vop);
-	spin_unlock(&vop->reg_lock);
 
-	/*
-	 * In order to write the LUT to the internal memory,
-	 * we need to first make sure the dsp_lut_en bit is cleared.
-	 */
-	ret = readx_poll_timeout(vop_dsp_lut_is_enabled, vop,
-				 idle, !idle, 5, 30 * 1000);
-	if (ret) {
-		DRM_DEV_ERROR(vop->dev, "display LUT RAM enable timeout!\n");
-		return;
-	}
+	if (!state->gamma_lut || !VOP_HAS_REG(vop, common, update_gamma_lut)) {
+		/*
+		 * To disable gamma (gamma_lut is null) or to write
+		 * an update to the LUT, clear dsp_lut_en.
+		 */
+		spin_lock(&vop->reg_lock);
+		VOP_REG_SET(vop, common, dsp_lut_en, 0);
+		vop_cfg_done(vop);
+		spin_unlock(&vop->reg_lock);
 
-	if (!state->gamma_lut)
-		return;
+		/*
+		 * In order to write the LUT to the internal memory,
+		 * we need to first make sure the dsp_lut_en bit is cleared.
+		 */
+		ret = readx_poll_timeout(vop_dsp_lut_is_enabled, vop,
+					 idle, !idle, 5, 30 * 1000);
+		if (ret) {
+			DRM_DEV_ERROR(vop->dev, "display LUT RAM enable timeout!\n");
+			return;
+		}
+
+		if (!state->gamma_lut)
+			return;
+	} else {
+		/*
+		 * On RK3399 the gamma LUT can updated without clearing dsp_lut_en,
+		 * by setting update_gamma_lut then waiting for lut_buffer_index change
+		 */
+		old_idx = vop_lut_buffer_index(vop);
+	}
 
 	spin_lock(&vop->reg_lock);
 	vop_crtc_write_gamma_lut(vop, crtc);
 	VOP_REG_SET(vop, common, dsp_lut_en, 1);
+	VOP_REG_SET(vop, common, update_gamma_lut, 1);
 	vop_cfg_done(vop);
 	spin_unlock(&vop->reg_lock);
+
+	if (VOP_HAS_REG(vop, common, update_gamma_lut)) {
+		ret = readx_poll_timeout(vop_lut_buffer_index, vop,
+					 lut_idx, lut_idx != old_idx, 5, 30 * 1000);
+		if (ret) {
+			DRM_DEV_ERROR(vop->dev, "gamma LUT update timeout!\n");
+			return;
+		}
+
+		/*
+		 * update_gamma_lut is auto cleared by HW, but write 0 to clear the bit
+		 * in our backup of the regs.
+		 */
+		spin_lock(&vop->reg_lock);
+		VOP_REG_SET(vop, common, update_gamma_lut, 0);
+		spin_unlock(&vop->reg_lock);
+	}
 }
 
 static void vop_crtc_atomic_begin(struct drm_crtc *crtc,
@@ -1303,14 +1349,6 @@
 		return;
 	}
 
-	/*
-	 * If we have a GAMMA LUT in the state, then let's make sure
-	 * it's updated. We might be coming out of suspend,
-	 * which means the LUT internal memory needs to be re-written.
-	 */
-	if (crtc->state->gamma_lut)
-		vop_crtc_gamma_set(vop, crtc, old_state);
-
 	mutex_lock(&vop->vop_lock);
 
 	WARN_ON(vop->event);
@@ -1401,6 +1439,14 @@
 
 	VOP_REG_SET(vop, common, standby, 0);
 	mutex_unlock(&vop->vop_lock);
+
+	/*
+	 * If we have a GAMMA LUT in the state, then let's make sure
+	 * it's updated. We might be coming out of suspend,
+	 * which means the LUT internal memory needs to be re-written.
+	 */
+	if (crtc->state->gamma_lut)
+		vop_crtc_gamma_set(vop, crtc, old_state);
 }
 
 static bool vop_fs_irq_is_pending(struct vop *vop)
@@ -1498,6 +1544,10 @@
 	VOP_AFBC_SET(vop, enable, s->enable_afbc);
 	vop_cfg_done(vop);
 
+	/* Ack the DMA transfer of the previous frame (RK3066). */
+	if (VOP_HAS_REG(vop, common, dma_stop))
+		VOP_REG_SET(vop, common, dma_stop, 0);
+
 	spin_unlock(&vop->reg_lock);
 
 	/*
@@ -1550,7 +1600,11 @@
 {
 	struct rockchip_crtc_state *rockchip_state;
 
-	rockchip_state = kzalloc(sizeof(*rockchip_state), GFP_KERNEL);
+	if (WARN_ON(!crtc->state))
+		return NULL;
+
+	rockchip_state = kmemdup(to_rockchip_crtc_state(crtc->state),
+				 sizeof(*rockchip_state), GFP_KERNEL);
 	if (!rockchip_state)
 		return NULL;
 
@@ -1575,7 +1629,10 @@
 	if (crtc->state)
 		vop_crtc_destroy_state(crtc, crtc->state);
 
-	__drm_atomic_helper_crtc_reset(crtc, &crtc_state->base);
+	if (crtc_state)
+		__drm_atomic_helper_crtc_reset(crtc, &crtc_state->base);
+	else
+		__drm_atomic_helper_crtc_reset(crtc, NULL);
 }
 
 #ifdef CONFIG_DRM_ANALOGIX_DP
@@ -2116,15 +2173,15 @@
 	vop_win_init(vop);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	vop->len = resource_size(res);
 	vop->regs = devm_ioremap_resource(dev, res);
 	if (IS_ERR(vop->regs))
 		return PTR_ERR(vop->regs);
+	vop->len = resource_size(res);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 	if (res) {
-		if (!vop_data->lut_size) {
-			DRM_DEV_ERROR(dev, "no gamma LUT size defined\n");
+		if (vop_data->lut_size != 1024 && vop_data->lut_size != 256) {
+			DRM_DEV_ERROR(dev, "unsupported gamma LUT size %d\n", vop_data->lut_size);
 			return -EINVAL;
 		}
 		vop->lut_regs = devm_ioremap_resource(dev, res);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rockchip_drm_vop.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rockchip_drm_vop.h
@@ -99,8 +99,11 @@
 	struct vop_reg dither_down_en;
 	struct vop_reg dither_up;
 	struct vop_reg dsp_lut_en;
+	struct vop_reg update_gamma_lut;
+	struct vop_reg lut_buffer_index;
 	struct vop_reg gate_en;
 	struct vop_reg mmu_en;
+	struct vop_reg dma_stop;
 	struct vop_reg out_mode;
 	struct vop_reg standby;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rockchip_lvds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rockchip_lvds.c
@@ -145,7 +145,7 @@
 		DRM_DEV_ERROR(lvds->dev, "failed to enable lvds pclk %d\n", ret);
 		return ret;
 	}
-	ret = pm_runtime_get_sync(lvds->dev);
+	ret = pm_runtime_resume_and_get(lvds->dev);
 	if (ret < 0) {
 		DRM_DEV_ERROR(lvds->dev, "failed to get pm runtime: %d\n", ret);
 		clk_disable(lvds->pclk);
@@ -329,16 +329,20 @@
 {
 	int ret;
 
-	ret = pm_runtime_get_sync(lvds->dev);
+	ret = pm_runtime_resume_and_get(lvds->dev);
 	if (ret < 0) {
 		DRM_DEV_ERROR(lvds->dev, "failed to get pm runtime: %d\n", ret);
 		return ret;
 	}
 
 	/* Enable LVDS mode */
-	return regmap_update_bits(lvds->grf, PX30_LVDS_GRF_PD_VO_CON1,
+	ret = regmap_update_bits(lvds->grf, PX30_LVDS_GRF_PD_VO_CON1,
 				  PX30_LVDS_MODE_EN(1) | PX30_LVDS_P2S_EN(1),
 				  PX30_LVDS_MODE_EN(1) | PX30_LVDS_P2S_EN(1));
+	if (ret)
+		pm_runtime_put(lvds->dev);
+
+	return ret;
 }
 
 static void px30_lvds_poweroff(struct rockchip_lvds *lvds)
@@ -568,8 +572,7 @@
 		ret = -EINVAL;
 		goto err_put_port;
 	} else if (ret) {
-		DRM_DEV_ERROR(dev, "failed to find panel and bridge node\n");
-		ret = -EPROBE_DEFER;
+		dev_err_probe(dev, ret, "failed to find panel and bridge node\n");
 		goto err_put_port;
 	}
 	if (lvds->panel)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rockchip_vop_reg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rockchip_vop_reg.c
@@ -424,6 +424,7 @@
 };
 
 static const struct vop_common rk3066_common = {
+	.dma_stop = VOP_REG(RK3066_SYS_CTRL0, 0x1, 0),
 	.standby = VOP_REG(RK3066_SYS_CTRL0, 0x1, 1),
 	.out_mode = VOP_REG(RK3066_DSP_CTRL0, 0xf, 0),
 	.cfg_done = VOP_REG(RK3066_REG_CFG_DONE, 0x1, 0),
@@ -865,6 +866,24 @@
 	.mipi_dual_channel_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 3),
 };
 
+static const struct vop_common rk3399_common = {
+	.standby = VOP_REG_SYNC(RK3399_SYS_CTRL, 0x1, 22),
+	.gate_en = VOP_REG(RK3399_SYS_CTRL, 0x1, 23),
+	.mmu_en = VOP_REG(RK3399_SYS_CTRL, 0x1, 20),
+	.dither_down_sel = VOP_REG(RK3399_DSP_CTRL1, 0x1, 4),
+	.dither_down_mode = VOP_REG(RK3399_DSP_CTRL1, 0x1, 3),
+	.dither_down_en = VOP_REG(RK3399_DSP_CTRL1, 0x1, 2),
+	.pre_dither_down = VOP_REG(RK3399_DSP_CTRL1, 0x1, 1),
+	.dither_up = VOP_REG(RK3399_DSP_CTRL1, 0x1, 6),
+	.dsp_lut_en = VOP_REG(RK3399_DSP_CTRL1, 0x1, 0),
+	.update_gamma_lut = VOP_REG(RK3399_DSP_CTRL1, 0x1, 7),
+	.lut_buffer_index = VOP_REG(RK3399_DBG_POST_REG1, 0x1, 1),
+	.data_blank = VOP_REG(RK3399_DSP_CTRL0, 0x1, 19),
+	.dsp_blank = VOP_REG(RK3399_DSP_CTRL0, 0x3, 18),
+	.out_mode = VOP_REG(RK3399_DSP_CTRL0, 0xf, 0),
+	.cfg_done = VOP_REG_SYNC(RK3399_REG_CFG_DONE, 0x1, 0),
+};
+
 static const struct vop_yuv2yuv_phy rk3399_yuv2yuv_win01_data = {
 	.y2r_coefficients = {
 		VOP_REG(RK3399_WIN0_YUV2YUV_Y2R + 0, 0xffff, 0),
@@ -902,6 +921,7 @@
 	.enable = VOP_REG(RK3288_WIN0_CTRL0, 0x1, 0),
 	.format = VOP_REG(RK3288_WIN0_CTRL0, 0x7, 1),
 	.rb_swap = VOP_REG(RK3288_WIN0_CTRL0, 0x1, 12),
+	.x_mir_en = VOP_REG(RK3288_WIN0_CTRL0, 0x1, 21),
 	.y_mir_en = VOP_REG(RK3288_WIN0_CTRL0, 0x1, 22),
 	.act_info = VOP_REG(RK3288_WIN0_ACT_INFO, 0x1fff1fff, 0),
 	.dsp_info = VOP_REG(RK3288_WIN0_DSP_INFO, 0x0fff0fff, 0),
@@ -912,6 +932,7 @@
 	.uv_vir = VOP_REG(RK3288_WIN0_VIR, 0x3fff, 16),
 	.src_alpha_ctl = VOP_REG(RK3288_WIN0_SRC_ALPHA_CTRL, 0xff, 0),
 	.dst_alpha_ctl = VOP_REG(RK3288_WIN0_DST_ALPHA_CTRL, 0xff, 0),
+	.channel = VOP_REG(RK3288_WIN0_CTRL2, 0xff, 0),
 };
 
 /*
@@ -922,11 +943,11 @@
 static const struct vop_win_data rk3399_vop_win_data[] = {
 	{ .base = 0x00, .phy = &rk3399_win01_data,
 	  .type = DRM_PLANE_TYPE_PRIMARY },
-	{ .base = 0x40, .phy = &rk3288_win01_data,
+	{ .base = 0x40, .phy = &rk3368_win01_data,
 	  .type = DRM_PLANE_TYPE_OVERLAY },
-	{ .base = 0x00, .phy = &rk3288_win23_data,
+	{ .base = 0x00, .phy = &rk3368_win23_data,
 	  .type = DRM_PLANE_TYPE_OVERLAY },
-	{ .base = 0x50, .phy = &rk3288_win23_data,
+	{ .base = 0x50, .phy = &rk3368_win23_data,
 	  .type = DRM_PLANE_TYPE_CURSOR },
 };
 
@@ -944,7 +965,7 @@
 	.version = VOP_VERSION(3, 5),
 	.feature = VOP_FEATURE_OUTPUT_RGB10,
 	.intr = &rk3366_vop_intr,
-	.common = &rk3288_common,
+	.common = &rk3399_common,
 	.modeset = &rk3288_modeset,
 	.output = &rk3399_output,
 	.afbc = &rk3399_vop_afbc,
@@ -952,6 +973,7 @@
 	.win = rk3399_vop_win_data,
 	.win_size = ARRAY_SIZE(rk3399_vop_win_data),
 	.win_yuv2yuv = rk3399_vop_big_win_yuv2yuv_data,
+	.lut_size = 1024,
 };
 
 static const struct vop_win_data rk3399_vop_lit_win_data[] = {
@@ -970,13 +992,14 @@
 static const struct vop_data rk3399_vop_lit = {
 	.version = VOP_VERSION(3, 6),
 	.intr = &rk3366_vop_intr,
-	.common = &rk3288_common,
+	.common = &rk3399_common,
 	.modeset = &rk3288_modeset,
 	.output = &rk3399_output,
 	.misc = &rk3368_misc,
 	.win = rk3399_vop_lit_win_data,
 	.win_size = ARRAY_SIZE(rk3399_vop_lit_win_data),
 	.win_yuv2yuv = rk3399_vop_lit_win_yuv2yuv_data,
+	.lut_size = 256,
 };
 
 static const struct vop_win_data rk3228_vop_win_data[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/rockchip/rockchip_vop_reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/rockchip/rockchip_vop_reg.h
@@ -628,6 +628,7 @@
 #define RK3399_YUV2YUV_WIN			0x02c0
 #define RK3399_YUV2YUV_POST			0x02c4
 #define RK3399_AUTO_GATING_EN			0x02cc
+#define RK3399_DBG_POST_REG1			0x036c
 #define RK3399_WIN0_CSC_COE			0x03a0
 #define RK3399_WIN1_CSC_COE			0x03c0
 #define RK3399_WIN2_CSC_COE			0x03e0
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/scheduler/gpu_scheduler_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/scheduler/gpu_scheduler_trace.h
@@ -21,7 +21,7 @@
  *
  */
 
-#if !defined(_GPU_SCHED_TRACE_H) || defined(TRACE_HEADER_MULTI_READ)
+#if !defined(_GPU_SCHED_TRACE_H_) || defined(TRACE_HEADER_MULTI_READ)
 #define _GPU_SCHED_TRACE_H_
 
 #include <linux/stringify.h>
@@ -123,7 +123,7 @@
 		      __entry->seqno)
 );
 
-#endif
+#endif /* _GPU_SCHED_TRACE_H_ */
 
 /* This part must be outside protection */
 #undef TRACE_INCLUDE_PATH
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/scheduler/sched_entity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/scheduler/sched_entity.c
@@ -99,8 +99,10 @@
 {
 	WARN_ON(!num_sched_list || !sched_list);
 
+	spin_lock(&entity->rq_lock);
 	entity->sched_list = sched_list;
 	entity->num_sched_list = num_sched_list;
+	spin_unlock(&entity->rq_lock);
 }
 EXPORT_SYMBOL(drm_sched_entity_modify_sched);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/scheduler/sched_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/scheduler/sched_main.c
@@ -698,8 +698,7 @@
 						typeof(*next), list);
 		if (next)
 			next->s_fence->scheduled.timestamp =
-				job->s_fence->finished.timestamp;
-
+				dma_fence_timestamp(&job->s_fence->finished);
 	} else {
 		job = NULL;
 		/* queue timeout for next job */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/selftests/test-drm_dp_mst_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/selftests/test-drm_dp_mst_helper.c
@@ -131,8 +131,10 @@
 		return false;
 
 	txmsg = kzalloc(sizeof(*txmsg), GFP_KERNEL);
-	if (!txmsg)
+	if (!txmsg) {
+		kfree(out);
 		return false;
+	}
 
 	drm_dp_encode_sideband_req(in, txmsg);
 	ret = drm_dp_decode_sideband_req(txmsg, out);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_cursor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_cursor.c
@@ -199,6 +199,9 @@
 		return 0;
 
 	crtc_state = drm_atomic_get_crtc_state(state, crtc);
+	if (IS_ERR(crtc_state))
+		return PTR_ERR(crtc_state);
+
 	mode = &crtc_state->mode;
 	dst_x = new_plane_state->crtc_x;
 	dst_y = new_plane_state->crtc_y;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_dvo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_dvo.c
@@ -288,7 +288,7 @@
 
 	DRM_DEBUG_DRIVER("\n");
 
-	memcpy(&dvo->mode, mode, sizeof(struct drm_display_mode));
+	drm_mode_copy(&dvo->mode, mode);
 
 	/* According to the path used (main or aux), the dvo clocks should
 	 * have a different parent clock. */
@@ -346,8 +346,9 @@
 
 #define CLK_TOLERANCE_HZ 50
 
-static int sti_dvo_connector_mode_valid(struct drm_connector *connector,
-					struct drm_display_mode *mode)
+static enum drm_mode_status
+sti_dvo_connector_mode_valid(struct drm_connector *connector,
+			     struct drm_display_mode *mode)
 {
 	int target = mode->clock * 1000;
 	int target_min = target - CLK_TOLERANCE_HZ;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_gdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_gdp.c
@@ -636,6 +636,9 @@
 
 	mixer = to_sti_mixer(crtc);
 	crtc_state = drm_atomic_get_crtc_state(state, crtc);
+	if (IS_ERR(crtc_state))
+		return PTR_ERR(crtc_state);
+
 	mode = &crtc_state->mode;
 	dst_x = new_plane_state->crtc_x;
 	dst_y = new_plane_state->crtc_y;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_hda.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_hda.c
@@ -523,7 +523,7 @@
 
 	DRM_DEBUG_DRIVER("\n");
 
-	memcpy(&hda->mode, mode, sizeof(struct drm_display_mode));
+	drm_mode_copy(&hda->mode, mode);
 
 	if (!hda_get_mode_idx(hda->mode, &mode_idx)) {
 		DRM_ERROR("Undefined mode\n");
@@ -600,8 +600,9 @@
 
 #define CLK_TOLERANCE_HZ 50
 
-static int sti_hda_connector_mode_valid(struct drm_connector *connector,
-					struct drm_display_mode *mode)
+static enum drm_mode_status
+sti_hda_connector_mode_valid(struct drm_connector *connector,
+			     struct drm_display_mode *mode)
 {
 	int target = mode->clock * 1000;
 	int target_min = target - CLK_TOLERANCE_HZ;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_hdmi.c
@@ -940,7 +940,7 @@
 	DRM_DEBUG_DRIVER("\n");
 
 	/* Copy the drm display mode in the connector local structure */
-	memcpy(&hdmi->mode, mode, sizeof(struct drm_display_mode));
+	drm_mode_copy(&hdmi->mode, mode);
 
 	/* Update clock framerate according to the selected mode */
 	ret = clk_set_rate(hdmi->clk_pix, mode->clock * 1000);
@@ -1003,8 +1003,9 @@
 
 #define CLK_TOLERANCE_HZ 50
 
-static int sti_hdmi_connector_mode_valid(struct drm_connector *connector,
-					struct drm_display_mode *mode)
+static enum drm_mode_status
+sti_hdmi_connector_mode_valid(struct drm_connector *connector,
+			      struct drm_display_mode *mode)
 {
 	int target = mode->clock * 1000;
 	int target_min = target - CLK_TOLERANCE_HZ;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_hqvdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_hqvdp.c
@@ -1035,6 +1035,9 @@
 		return 0;
 
 	crtc_state = drm_atomic_get_crtc_state(state, crtc);
+	if (IS_ERR(crtc_state))
+		return PTR_ERR(crtc_state);
+
 	mode = &crtc_state->mode;
 	dst_x = new_plane_state->crtc_x;
 	dst_y = new_plane_state->crtc_y;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sti/sti_mixer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sti/sti_mixer.c
@@ -137,7 +137,7 @@
 	}
 }
 
-static void mixer_dbg_mxn(struct seq_file *s, void *addr)
+static void mixer_dbg_mxn(struct seq_file *s, void __iomem *addr)
 {
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/stm/drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/stm/drv.c
@@ -195,12 +195,14 @@
 
 	ret = drm_dev_register(ddev, 0);
 	if (ret)
-		goto err_put;
+		goto err_unload;
 
 	drm_fbdev_generic_setup(ddev, 16);
 
 	return 0;
 
+err_unload:
+	drv_unload(ddev);
 err_put:
 	drm_dev_put(ddev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/stm/ltdc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/stm/ltdc.c
@@ -528,8 +528,8 @@
 	struct drm_device *ddev = crtc->dev;
 	struct drm_connector_list_iter iter;
 	struct drm_connector *connector = NULL;
-	struct drm_encoder *encoder = NULL;
-	struct drm_bridge *bridge = NULL;
+	struct drm_encoder *encoder = NULL, *en_iter;
+	struct drm_bridge *bridge = NULL, *br_iter;
 	struct drm_display_mode *mode = &crtc->state->adjusted_mode;
 	u32 hsync, vsync, accum_hbp, accum_vbp, accum_act_w, accum_act_h;
 	u32 total_width, total_height;
@@ -538,15 +538,19 @@
 	int ret;
 
 	/* get encoder from crtc */
-	drm_for_each_encoder(encoder, ddev)
-		if (encoder->crtc == crtc)
+	drm_for_each_encoder(en_iter, ddev)
+		if (en_iter->crtc == crtc) {
+			encoder = en_iter;
 			break;
+		}
 
 	if (encoder) {
 		/* get bridge from encoder */
-		list_for_each_entry(bridge, &encoder->bridge_chain, chain_node)
-			if (bridge->encoder == encoder)
+		list_for_each_entry(br_iter, &encoder->bridge_chain, chain_node)
+			if (br_iter->encoder == encoder) {
+				bridge = br_iter;
 				break;
+			}
 
 		/* Get the connector from encoder */
 		drm_connector_list_iter_begin(ddev, &iter);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/Kconfig
@@ -46,6 +46,7 @@
 	default MACH_SUN8I
 	select CRC_CCITT
 	select DRM_MIPI_DSI
+	select RESET_CONTROLLER
 	select PHY_SUN6I_MIPI_DPHY
 	help
 	  Choose this option if you want have an Allwinner SoC with
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun4i_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun4i_drv.c
@@ -72,7 +72,6 @@
 		goto free_drm;
 	}
 
-	dev_set_drvdata(dev, drm);
 	drm->dev_private = drv;
 	INIT_LIST_HEAD(&drv->frontend_list);
 	INIT_LIST_HEAD(&drv->engine_list);
@@ -95,12 +94,12 @@
 	/* drm_vblank_init calls kcalloc, which can fail */
 	ret = drm_vblank_init(drm, drm->mode_config.num_crtc);
 	if (ret)
-		goto cleanup_mode_config;
+		goto unbind_all;
 
 	/* Remove early framebuffers (ie. simplefb) */
 	ret = drm_aperture_remove_framebuffers(false, &sun4i_drv_driver);
 	if (ret)
-		goto cleanup_mode_config;
+		goto unbind_all;
 
 	sun4i_framebuffer_init(drm);
 
@@ -113,10 +112,14 @@
 
 	drm_fbdev_generic_setup(drm, 32);
 
+	dev_set_drvdata(dev, drm);
+
 	return 0;
 
 finish_poll:
 	drm_kms_helper_poll_fini(drm);
+unbind_all:
+	component_unbind_all(dev, NULL);
 cleanup_mode_config:
 	drm_mode_config_cleanup(drm);
 	of_reserved_mem_device_release(dev);
@@ -129,6 +132,7 @@
 {
 	struct drm_device *drm = dev_get_drvdata(dev);
 
+	dev_set_drvdata(dev, NULL);
 	drm_dev_unregister(drm);
 	drm_kms_helper_poll_fini(drm);
 	drm_atomic_helper_shutdown(drm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun4i_frontend.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun4i_frontend.c
@@ -222,13 +222,11 @@
 
 	/* Set the physical address of the buffer in memory */
 	paddr = drm_fb_cma_get_gem_addr(fb, state, 0);
-	paddr -= PHYS_OFFSET;
 	DRM_DEBUG_DRIVER("Setting buffer #0 address to %pad\n", &paddr);
 	regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR0_REG, paddr);
 
 	if (fb->format->num_planes > 1) {
 		paddr = drm_fb_cma_get_gem_addr(fb, state, swap ? 2 : 1);
-		paddr -= PHYS_OFFSET;
 		DRM_DEBUG_DRIVER("Setting buffer #1 address to %pad\n", &paddr);
 		regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR1_REG,
 			     paddr);
@@ -236,7 +234,6 @@
 
 	if (fb->format->num_planes > 2) {
 		paddr = drm_fb_cma_get_gem_addr(fb, state, swap ? 1 : 2);
-		paddr -= PHYS_OFFSET;
 		DRM_DEBUG_DRIVER("Setting buffer #2 address to %pad\n", &paddr);
 		regmap_write(frontend->regs, SUN4I_FRONTEND_BUF_ADDR2_REG,
 			     paddr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -777,21 +777,19 @@
 static int sun4i_tcon_init_clocks(struct device *dev,
 				  struct sun4i_tcon *tcon)
 {
-	tcon->clk = devm_clk_get(dev, "ahb");
+	tcon->clk = devm_clk_get_enabled(dev, "ahb");
 	if (IS_ERR(tcon->clk)) {
 		dev_err(dev, "Couldn't get the TCON bus clock\n");
 		return PTR_ERR(tcon->clk);
 	}
-	clk_prepare_enable(tcon->clk);
 
 	if (tcon->quirks->has_channel_0) {
-		tcon->sclk0 = devm_clk_get(dev, "tcon-ch0");
+		tcon->sclk0 = devm_clk_get_enabled(dev, "tcon-ch0");
 		if (IS_ERR(tcon->sclk0)) {
 			dev_err(dev, "Couldn't get the TCON channel 0 clock\n");
 			return PTR_ERR(tcon->sclk0);
 		}
 	}
-	clk_prepare_enable(tcon->sclk0);
 
 	if (tcon->quirks->has_channel_1) {
 		tcon->sclk1 = devm_clk_get(dev, "tcon-ch1");
@@ -804,12 +802,6 @@
 	return 0;
 }
 
-static void sun4i_tcon_free_clocks(struct sun4i_tcon *tcon)
-{
-	clk_disable_unprepare(tcon->sclk0);
-	clk_disable_unprepare(tcon->clk);
-}
-
 static int sun4i_tcon_init_irq(struct device *dev,
 			       struct sun4i_tcon *tcon)
 {
@@ -1224,14 +1216,14 @@
 	ret = sun4i_tcon_init_regmap(dev, tcon);
 	if (ret) {
 		dev_err(dev, "Couldn't init our TCON regmap\n");
-		goto err_free_clocks;
+		goto err_assert_reset;
 	}
 
 	if (tcon->quirks->has_channel_0) {
 		ret = sun4i_dclk_create(dev, tcon);
 		if (ret) {
 			dev_err(dev, "Couldn't create our TCON dot clock\n");
-			goto err_free_clocks;
+			goto err_assert_reset;
 		}
 	}
 
@@ -1294,8 +1286,6 @@
 err_free_dotclock:
 	if (tcon->quirks->has_channel_0)
 		sun4i_dclk_free(tcon);
-err_free_clocks:
-	sun4i_tcon_free_clocks(tcon);
 err_assert_reset:
 	reset_control_assert(tcon->lcd_rst);
 	return ret;
@@ -1309,7 +1299,6 @@
 	list_del(&tcon->list);
 	if (tcon->quirks->has_channel_0)
 		sun4i_dclk_free(tcon);
-	sun4i_tcon_free_clocks(tcon);
 }
 
 static const struct component_ops sun4i_tcon_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
@@ -531,7 +531,7 @@
 				    struct drm_display_mode *mode)
 {
 	struct mipi_dsi_device *device = dsi->device;
-	unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8;
+	int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8;
 	u16 hbp = 0, hfp = 0, hsa = 0, hblk = 0, vblk = 0;
 	u32 basic_ctl = 0;
 	size_t bytes;
@@ -555,7 +555,7 @@
 		 * (4 bytes). Its minimal size is therefore 10 bytes
 		 */
 #define HSA_PACKET_OVERHEAD	10
-		hsa = max((unsigned int)HSA_PACKET_OVERHEAD,
+		hsa = max(HSA_PACKET_OVERHEAD,
 			  (mode->hsync_end - mode->hsync_start) * Bpp - HSA_PACKET_OVERHEAD);
 
 		/*
@@ -564,7 +564,7 @@
 		 * therefore 6 bytes
 		 */
 #define HBP_PACKET_OVERHEAD	6
-		hbp = max((unsigned int)HBP_PACKET_OVERHEAD,
+		hbp = max(HBP_PACKET_OVERHEAD,
 			  (mode->htotal - mode->hsync_end) * Bpp - HBP_PACKET_OVERHEAD);
 
 		/*
@@ -574,7 +574,7 @@
 		 * 16 bytes
 		 */
 #define HFP_PACKET_OVERHEAD	16
-		hfp = max((unsigned int)HFP_PACKET_OVERHEAD,
+		hfp = max(HFP_PACKET_OVERHEAD,
 			  (mode->hsync_start - mode->hdisplay) * Bpp - HFP_PACKET_OVERHEAD);
 
 		/*
@@ -583,7 +583,7 @@
 		 * bytes). Its minimal size is therefore 10 bytes.
 		 */
 #define HBLK_PACKET_OVERHEAD	10
-		hblk = max((unsigned int)HBLK_PACKET_OVERHEAD,
+		hblk = max(HBLK_PACKET_OVERHEAD,
 			   (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp -
 			   HBLK_PACKET_OVERHEAD);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun8i_csc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun8i_csc.h
@@ -16,8 +16,8 @@
 #define CCSC10_OFFSET 0xA0000
 #define CCSC11_OFFSET 0xF0000
 
-#define SUN8I_CSC_CTRL(base)		(base + 0x0)
-#define SUN8I_CSC_COEFF(base, i)	(base + 0x10 + 4 * i)
+#define SUN8I_CSC_CTRL(base)		((base) + 0x0)
+#define SUN8I_CSC_COEFF(base, i)	((base) + 0x10 + 4 * (i))
 
 #define SUN8I_CSC_CTRL_EN		BIT(0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c
@@ -658,8 +658,10 @@
 		return -EPROBE_DEFER;
 
 	phy = platform_get_drvdata(pdev);
-	if (!phy)
+	if (!phy) {
+		put_device(&pdev->dev);
 		return -EPROBE_DEFER;
+	}
 
 	hdmi->phy = phy;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/sun4i/sun8i_mixer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/sun4i/sun8i_mixer.h
@@ -111,10 +111,10 @@
 /* format 13 is semi-planar YUV411 VUVU */
 #define SUN8I_MIXER_FBFMT_YUV411	14
 /* format 15 doesn't exist */
-/* format 16 is P010 YVU */
-#define SUN8I_MIXER_FBFMT_P010_YUV	17
-/* format 18 is P210 YVU */
-#define SUN8I_MIXER_FBFMT_P210_YUV	19
+#define SUN8I_MIXER_FBFMT_P010_YUV	16
+/* format 17 is P010 YVU */
+#define SUN8I_MIXER_FBFMT_P210_YUV	18
+/* format 19 is P210 YVU */
 /* format 20 is packed YVU444 10-bit */
 /* format 21 is packed YUV444 10-bit */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/Kconfig
@@ -5,6 +5,7 @@
 	depends on COMMON_CLK
 	depends on DRM
 	depends on OF
+	select DRM_DP_AUX_BUS
 	select DRM_KMS_HELPER
 	select DRM_MIPI_DSI
 	select DRM_PANEL
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/dc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/dc.c
@@ -1762,10 +1762,9 @@
 	return 0;
 }
 
-static void tegra_dc_commit_state(struct tegra_dc *dc,
-				  struct tegra_dc_state *state)
+static void tegra_dc_set_clock_rate(struct tegra_dc *dc,
+				    struct tegra_dc_state *state)
 {
-	u32 value;
 	int err;
 
 	err = clk_set_parent(dc->clk, state->clk);
@@ -1796,11 +1795,6 @@
 	DRM_DEBUG_KMS("rate: %lu, div: %u\n", clk_get_rate(dc->clk),
 		      state->div);
 	DRM_DEBUG_KMS("pclk: %lu\n", state->pclk);
-
-	if (!dc->soc->has_nvdisplay) {
-		value = SHIFT_CLK_DIVIDER(state->div) | PIXEL_CLK_DIVIDER_PCD1;
-		tegra_dc_writel(dc, value, DC_DISP_DISP_CLOCK_CONTROL);
-	}
 }
 
 static void tegra_dc_stop(struct tegra_dc *dc)
@@ -2002,6 +1996,9 @@
 	u32 value;
 	int err;
 
+	/* apply PLL changes */
+	tegra_dc_set_clock_rate(dc, crtc_state);
+
 	err = host1x_client_resume(&dc->client);
 	if (err < 0) {
 		dev_err(dc->dev, "failed to resume: %d\n", err);
@@ -2076,8 +2073,11 @@
 	else
 		tegra_dc_writel(dc, 0, DC_DISP_BORDER_COLOR);
 
-	/* apply PLL and pixel clock changes */
-	tegra_dc_commit_state(dc, crtc_state);
+	/* apply pixel clock changes */
+	if (!dc->soc->has_nvdisplay) {
+		value = SHIFT_CLK_DIVIDER(crtc_state->div) | PIXEL_CLK_DIVIDER_PCD1;
+		tegra_dc_writel(dc, value, DC_DISP_DISP_CLOCK_CONTROL);
+	}
 
 	/* program display mode */
 	tegra_dc_set_timings(dc, mode);
@@ -2685,6 +2685,7 @@
 	.has_win_b_vfilter_mem_client = true,
 	.has_win_c_without_vert_filter = true,
 	.plane_tiled_memory_bandwidth_x2 = false,
+	.has_pll_d2_out0 = false,
 };
 
 static const struct tegra_dc_soc_info tegra30_dc_soc_info = {
@@ -2707,6 +2708,7 @@
 	.has_win_b_vfilter_mem_client = true,
 	.has_win_c_without_vert_filter = false,
 	.plane_tiled_memory_bandwidth_x2 = true,
+	.has_pll_d2_out0 = true,
 };
 
 static const struct tegra_dc_soc_info tegra114_dc_soc_info = {
@@ -2729,6 +2731,7 @@
 	.has_win_b_vfilter_mem_client = false,
 	.has_win_c_without_vert_filter = false,
 	.plane_tiled_memory_bandwidth_x2 = true,
+	.has_pll_d2_out0 = true,
 };
 
 static const struct tegra_dc_soc_info tegra124_dc_soc_info = {
@@ -2751,6 +2754,7 @@
 	.has_win_b_vfilter_mem_client = false,
 	.has_win_c_without_vert_filter = false,
 	.plane_tiled_memory_bandwidth_x2 = false,
+	.has_pll_d2_out0 = true,
 };
 
 static const struct tegra_dc_soc_info tegra210_dc_soc_info = {
@@ -2773,6 +2777,7 @@
 	.has_win_b_vfilter_mem_client = false,
 	.has_win_c_without_vert_filter = false,
 	.plane_tiled_memory_bandwidth_x2 = false,
+	.has_pll_d2_out0 = true,
 };
 
 static const struct tegra_windowgroup_soc tegra186_dc_wgrps[] = {
@@ -2823,6 +2828,7 @@
 	.wgrps = tegra186_dc_wgrps,
 	.num_wgrps = ARRAY_SIZE(tegra186_dc_wgrps),
 	.plane_tiled_memory_bandwidth_x2 = false,
+	.has_pll_d2_out0 = false,
 };
 
 static const struct tegra_windowgroup_soc tegra194_dc_wgrps[] = {
@@ -2873,6 +2879,7 @@
 	.wgrps = tegra194_dc_wgrps,
 	.num_wgrps = ARRAY_SIZE(tegra194_dc_wgrps),
 	.plane_tiled_memory_bandwidth_x2 = false,
+	.has_pll_d2_out0 = false,
 };
 
 static const struct of_device_id tegra_dc_of_match[] = {
@@ -3022,8 +3029,10 @@
 	usleep_range(2000, 4000);
 
 	err = reset_control_assert(dc->rst);
-	if (err < 0)
+	if (err < 0) {
+		clk_disable_unprepare(dc->clk);
 		return err;
+	}
 
 	usleep_range(2000, 4000);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/dc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/dc.h
@@ -76,6 +76,7 @@
 	bool has_win_b_vfilter_mem_client;
 	bool has_win_c_without_vert_filter;
 	bool plane_tiled_memory_bandwidth_x2;
+	bool has_pll_d2_out0;
 };
 
 struct tegra_dc {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/dpaux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/dpaux.c
@@ -19,6 +19,7 @@
 #include <linux/workqueue.h>
 
 #include <drm/drm_dp_helper.h>
+#include <drm/drm_dp_aux_bus.h>
 #include <drm/drm_panel.h>
 
 #include "dp.h"
@@ -468,7 +469,7 @@
 
 	dpaux->irq = platform_get_irq(pdev, 0);
 	if (dpaux->irq < 0)
-		return -ENXIO;
+		return dpaux->irq;
 
 	if (!pdev->dev.pm_domain) {
 		dpaux->rst = devm_reset_control_get(&pdev->dev, "dpaux");
@@ -524,7 +525,7 @@
 	if (err < 0) {
 		dev_err(dpaux->dev, "failed to request IRQ#%u: %d\n",
 			dpaux->irq, err);
-		return err;
+		goto err_pm_disable;
 	}
 
 	disable_irq(dpaux->irq);
@@ -544,7 +545,7 @@
 	 */
 	err = tegra_dpaux_pad_config(dpaux, DPAUX_PADCTL_FUNC_I2C);
 	if (err < 0)
-		return err;
+		goto err_pm_disable;
 
 #ifdef CONFIG_GENERIC_PINCONF
 	dpaux->desc.name = dev_name(&pdev->dev);
@@ -557,7 +558,8 @@
 	dpaux->pinctrl = devm_pinctrl_register(&pdev->dev, &dpaux->desc, dpaux);
 	if (IS_ERR(dpaux->pinctrl)) {
 		dev_err(&pdev->dev, "failed to register pincontrol\n");
-		return PTR_ERR(dpaux->pinctrl);
+		err = PTR_ERR(dpaux->pinctrl);
+		goto err_pm_disable;
 	}
 #endif
 	/* enable and clear all interrupts */
@@ -570,7 +572,18 @@
 	list_add_tail(&dpaux->list, &dpaux_list);
 	mutex_unlock(&dpaux_lock);
 
+	err = devm_of_dp_aux_populate_ep_devices(&dpaux->aux);
+	if (err < 0) {
+		dev_err(dpaux->dev, "failed to populate AUX bus: %d\n", err);
+		goto err_pm_disable;
+	}
+
 	return 0;
+
+err_pm_disable:
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	return err;
 }
 
 static int tegra_dpaux_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/drm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/drm.c
@@ -21,6 +21,10 @@
 #include <drm/drm_prime.h>
 #include <drm/drm_vblank.h>
 
+#if IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU)
+#include <asm/dma-iommu.h>
+#endif
+
 #include "dc.h"
 #include "drm.h"
 #include "gem.h"
@@ -936,6 +940,17 @@
 	struct iommu_group *group = NULL;
 	int err;
 
+#if IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU)
+	if (client->dev->archdata.mapping) {
+		struct dma_iommu_mapping *mapping =
+				to_dma_iommu_mapping(client->dev);
+		arm_iommu_detach_device(client->dev);
+		arm_iommu_release_mapping(mapping);
+
+		domain = iommu_get_domain_for_dev(client->dev);
+	}
+#endif
+
 	/*
 	 * If the host1x client is already attached to an IOMMU domain that is
 	 * not the shared IOMMU domain, don't try to attach it to a different
@@ -1068,6 +1083,10 @@
 	struct host1x *host1x = dev_get_drvdata(dev->dev.parent);
 	struct iommu_domain *domain;
 
+	/* Our IOMMU usage policy doesn't currently play well with GART */
+	if (of_machine_is_compatible("nvidia,tegra20"))
+		return false;
+
 	/*
 	 * If the Tegra DRM clients are backed by an IOMMU, push buffers are
 	 * likely to be allocated beyond the 32-bit boundary if sufficient
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/dsi.c
@@ -1534,12 +1534,16 @@
 	np = of_parse_phandle(dsi->dev->of_node, "nvidia,ganged-mode", 0);
 	if (np) {
 		struct platform_device *gangster = of_find_device_by_node(np);
+		of_node_put(np);
+		if (!gangster)
+			return -EPROBE_DEFER;
 
 		dsi->slave = platform_get_drvdata(gangster);
-		of_node_put(np);
 
-		if (!dsi->slave)
+		if (!dsi->slave) {
+			put_device(&gangster->dev);
 			return -EPROBE_DEFER;
+		}
 
 		dsi->slave->master = dsi;
 	}
@@ -1582,48 +1586,58 @@
 
 	if (!pdev->dev.pm_domain) {
 		dsi->rst = devm_reset_control_get(&pdev->dev, "dsi");
-		if (IS_ERR(dsi->rst))
-			return PTR_ERR(dsi->rst);
+		if (IS_ERR(dsi->rst)) {
+			err = PTR_ERR(dsi->rst);
+			goto remove;
+		}
 	}
 
 	dsi->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(dsi->clk)) {
-		dev_err(&pdev->dev, "cannot get DSI clock\n");
-		return PTR_ERR(dsi->clk);
+		err = dev_err_probe(&pdev->dev, PTR_ERR(dsi->clk),
+				    "cannot get DSI clock\n");
+		goto remove;
 	}
 
 	dsi->clk_lp = devm_clk_get(&pdev->dev, "lp");
 	if (IS_ERR(dsi->clk_lp)) {
-		dev_err(&pdev->dev, "cannot get low-power clock\n");
-		return PTR_ERR(dsi->clk_lp);
+		err = dev_err_probe(&pdev->dev, PTR_ERR(dsi->clk_lp),
+				    "cannot get low-power clock\n");
+		goto remove;
 	}
 
 	dsi->clk_parent = devm_clk_get(&pdev->dev, "parent");
 	if (IS_ERR(dsi->clk_parent)) {
-		dev_err(&pdev->dev, "cannot get parent clock\n");
-		return PTR_ERR(dsi->clk_parent);
+		err = dev_err_probe(&pdev->dev, PTR_ERR(dsi->clk_parent),
+				    "cannot get parent clock\n");
+		goto remove;
 	}
 
 	dsi->vdd = devm_regulator_get(&pdev->dev, "avdd-dsi-csi");
 	if (IS_ERR(dsi->vdd)) {
-		dev_err(&pdev->dev, "cannot get VDD supply\n");
-		return PTR_ERR(dsi->vdd);
+		err = dev_err_probe(&pdev->dev, PTR_ERR(dsi->vdd),
+				    "cannot get VDD supply\n");
+		goto remove;
 	}
 
 	err = tegra_dsi_setup_clocks(dsi);
 	if (err < 0) {
 		dev_err(&pdev->dev, "cannot setup clocks\n");
-		return err;
+		goto remove;
 	}
 
 	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dsi->regs = devm_ioremap_resource(&pdev->dev, regs);
-	if (IS_ERR(dsi->regs))
-		return PTR_ERR(dsi->regs);
+	if (IS_ERR(dsi->regs)) {
+		err = PTR_ERR(dsi->regs);
+		goto remove;
+	}
 
 	dsi->mipi = tegra_mipi_request(&pdev->dev, pdev->dev.of_node);
-	if (IS_ERR(dsi->mipi))
-		return PTR_ERR(dsi->mipi);
+	if (IS_ERR(dsi->mipi)) {
+		err = PTR_ERR(dsi->mipi);
+		goto remove;
+	}
 
 	dsi->host.ops = &tegra_dsi_host_ops;
 	dsi->host.dev = &pdev->dev;
@@ -1651,9 +1665,12 @@
 	return 0;
 
 unregister:
+	pm_runtime_disable(&pdev->dev);
 	mipi_dsi_host_unregister(&dsi->host);
 mipi_free:
 	tegra_mipi_free(dsi->mipi);
+remove:
+	tegra_output_remove(&dsi->output);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/fb.c
@@ -165,6 +165,7 @@
 
 		if (gem->size < size) {
 			err = -EINVAL;
+			drm_gem_object_put(gem);
 			goto unreference;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/firewall.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/firewall.c
@@ -97,6 +97,9 @@
 {
 	bool is_addr;
 
+	if (!fw->client->ops->is_addr_reg)
+		return 0;
+
 	is_addr = fw->client->ops->is_addr_reg(fw->client->base.dev, fw->class,
 					       offset);
 	if (is_addr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/gr2d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/gr2d.c
@@ -4,9 +4,11 @@
  */
 
 #include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/iommu.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
+#include <linux/reset.h>
 
 #include "drm.h"
 #include "gem.h"
@@ -19,6 +21,7 @@
 struct gr2d {
 	struct tegra_drm_client client;
 	struct host1x_channel *channel;
+	struct reset_control *rst;
 	struct clk *clk;
 
 	const struct gr2d_soc *soc;
@@ -208,6 +211,12 @@
 	if (!syncpts)
 		return -ENOMEM;
 
+	gr2d->rst = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(gr2d->rst)) {
+		dev_err(dev, "cannot get reset\n");
+		return PTR_ERR(gr2d->rst);
+	}
+
 	gr2d->clk = devm_clk_get(dev, NULL);
 	if (IS_ERR(gr2d->clk)) {
 		dev_err(dev, "cannot get clock\n");
@@ -220,6 +229,14 @@
 		return err;
 	}
 
+	usleep_range(2000, 4000);
+
+	err = reset_control_deassert(gr2d->rst);
+	if (err < 0) {
+		dev_err(dev, "failed to deassert reset: %d\n", err);
+		goto disable_clk;
+	}
+
 	INIT_LIST_HEAD(&gr2d->client.base.list);
 	gr2d->client.base.ops = &gr2d_client_ops;
 	gr2d->client.base.dev = dev;
@@ -234,8 +251,7 @@
 	err = host1x_client_register(&gr2d->client.base);
 	if (err < 0) {
 		dev_err(dev, "failed to register host1x client: %d\n", err);
-		clk_disable_unprepare(gr2d->clk);
-		return err;
+		goto assert_rst;
 	}
 
 	/* initialize address register map */
@@ -245,6 +261,13 @@
 	platform_set_drvdata(pdev, gr2d);
 
 	return 0;
+
+assert_rst:
+	(void)reset_control_assert(gr2d->rst);
+disable_clk:
+	clk_disable_unprepare(gr2d->clk);
+
+	return err;
 }
 
 static int gr2d_remove(struct platform_device *pdev)
@@ -259,6 +282,12 @@
 		return err;
 	}
 
+	err = reset_control_assert(gr2d->rst);
+	if (err < 0)
+		dev_err(&pdev->dev, "failed to assert reset: %d\n", err);
+
+	usleep_range(2000, 4000);
+
 	clk_disable_unprepare(gr2d->clk);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/output.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/output.c
@@ -139,8 +139,10 @@
 						       GPIOD_IN,
 						       "HDMI hotplug detect");
 	if (IS_ERR(output->hpd_gpio)) {
-		if (PTR_ERR(output->hpd_gpio) != -ENOENT)
-			return PTR_ERR(output->hpd_gpio);
+		if (PTR_ERR(output->hpd_gpio) != -ENOENT) {
+			err = PTR_ERR(output->hpd_gpio);
+			goto put_i2c;
+		}
 
 		output->hpd_gpio = NULL;
 	}
@@ -149,7 +151,7 @@
 		err = gpiod_to_irq(output->hpd_gpio);
 		if (err < 0) {
 			dev_err(output->dev, "gpiod_to_irq(): %d\n", err);
-			return err;
+			goto put_i2c;
 		}
 
 		output->hpd_irq = err;
@@ -162,7 +164,7 @@
 		if (err < 0) {
 			dev_err(output->dev, "failed to request IRQ#%u: %d\n",
 				output->hpd_irq, err);
-			return err;
+			goto put_i2c;
 		}
 
 		output->connector.polled = DRM_CONNECTOR_POLL_HPD;
@@ -176,6 +178,12 @@
 	}
 
 	return 0;
+
+put_i2c:
+	if (output->ddc)
+		i2c_put_adapter(output->ddc);
+
+	return err;
 }
 
 void tegra_output_remove(struct tegra_output *output)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/rgb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/rgb.c
@@ -17,6 +17,8 @@
 	struct tegra_output output;
 	struct tegra_dc *dc;
 
+	struct clk *pll_d_out0;
+	struct clk *pll_d2_out0;
 	struct clk *clk_parent;
 	struct clk *clk;
 };
@@ -123,6 +125,18 @@
 	tegra_dc_commit(rgb->dc);
 }
 
+static bool tegra_rgb_pll_rate_change_allowed(struct tegra_rgb *rgb)
+{
+	if (!rgb->pll_d2_out0)
+		return false;
+
+	if (!clk_is_match(rgb->clk_parent, rgb->pll_d_out0) &&
+	    !clk_is_match(rgb->clk_parent, rgb->pll_d2_out0))
+		return false;
+
+	return true;
+}
+
 static int
 tegra_rgb_encoder_atomic_check(struct drm_encoder *encoder,
 			       struct drm_crtc_state *crtc_state,
@@ -151,8 +165,17 @@
 	 * and hope that the desired frequency can be matched (or at least
 	 * matched sufficiently close that the panel will still work).
 	 */
-	div = ((clk_get_rate(rgb->clk) * 2) / pclk) - 2;
-	pclk = 0;
+	if (tegra_rgb_pll_rate_change_allowed(rgb)) {
+		/*
+		 * Set display controller clock to x2 of PCLK in order to
+		 * produce higher resolution pulse positions.
+		 */
+		div = 2;
+		pclk *= 2;
+	} else {
+		div = ((clk_get_rate(rgb->clk) * 2) / pclk) - 2;
+		pclk = 0;
+	}
 
 	err = tegra_dc_state_setup_clock(dc, crtc_state, rgb->clk_parent,
 					 pclk, div);
@@ -195,31 +218,61 @@
 	rgb->clk = devm_clk_get(dc->dev, NULL);
 	if (IS_ERR(rgb->clk)) {
 		dev_err(dc->dev, "failed to get clock\n");
-		return PTR_ERR(rgb->clk);
+		err = PTR_ERR(rgb->clk);
+		goto remove;
 	}
 
 	rgb->clk_parent = devm_clk_get(dc->dev, "parent");
 	if (IS_ERR(rgb->clk_parent)) {
 		dev_err(dc->dev, "failed to get parent clock\n");
-		return PTR_ERR(rgb->clk_parent);
+		err = PTR_ERR(rgb->clk_parent);
+		goto remove;
 	}
 
 	err = clk_set_parent(rgb->clk, rgb->clk_parent);
 	if (err < 0) {
 		dev_err(dc->dev, "failed to set parent clock: %d\n", err);
-		return err;
+		goto remove;
+	}
+
+	rgb->pll_d_out0 = clk_get_sys(NULL, "pll_d_out0");
+	if (IS_ERR(rgb->pll_d_out0)) {
+		err = PTR_ERR(rgb->pll_d_out0);
+		dev_err(dc->dev, "failed to get pll_d_out0: %d\n", err);
+		goto remove;
+	}
+
+	if (dc->soc->has_pll_d2_out0) {
+		rgb->pll_d2_out0 = clk_get_sys(NULL, "pll_d2_out0");
+		if (IS_ERR(rgb->pll_d2_out0)) {
+			err = PTR_ERR(rgb->pll_d2_out0);
+			dev_err(dc->dev, "failed to get pll_d2_out0: %d\n", err);
+			goto put_pll;
+		}
 	}
 
 	dc->rgb = &rgb->output;
 
 	return 0;
+
+put_pll:
+	clk_put(rgb->pll_d_out0);
+remove:
+	tegra_output_remove(&rgb->output);
+	return err;
 }
 
 int tegra_dc_rgb_remove(struct tegra_dc *dc)
 {
+	struct tegra_rgb *rgb;
+
 	if (!dc->rgb)
 		return 0;
 
+	rgb = to_rgb(dc->rgb);
+	clk_put(rgb->pll_d2_out0);
+	clk_put(rgb->pll_d_out0);
+
 	tegra_output_remove(dc->rgb);
 	dc->rgb = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/sor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/sor.c
@@ -1153,7 +1153,7 @@
 				    struct drm_dp_link *link)
 {
 	const u64 f = 100000, link_rate = link->rate * 1000;
-	const u64 pclk = mode->clock * 1000;
+	const u64 pclk = (u64)mode->clock * 1000;
 	u64 input, output, watermark, num;
 	struct tegra_sor_params params;
 	u32 num_syms_per_line;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/submit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/submit.c
@@ -475,8 +475,10 @@
 	kfree(job_data->used_mappings);
 	kfree(job_data);
 
-	if (pm_runtime_enabled(client->base.dev))
+	if (pm_runtime_enabled(client->base.dev)) {
+		pm_runtime_mark_last_busy(client->base.dev);
 		pm_runtime_put_autosuspend(client->base.dev);
+	}
 }
 
 int tegra_drm_ioctl_channel_submit(struct drm_device *drm, void *data,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tegra/vic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tegra/vic.c
@@ -5,6 +5,7 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dma-mapping.h>
 #include <linux/host1x.h>
 #include <linux/iommu.h>
 #include <linux/module.h>
@@ -232,10 +233,8 @@
 
 	if (!client->group) {
 		virt = dma_alloc_coherent(vic->dev, size, &iova, GFP_KERNEL);
-
-		err = dma_mapping_error(vic->dev, iova);
-		if (err < 0)
-			return err;
+		if (!virt)
+			return -ENOMEM;
 	} else {
 		virt = tegra_drm_alloc(tegra, size, &iova);
 	}
@@ -276,7 +275,7 @@
 }
 
 
-static int vic_runtime_resume(struct device *dev)
+static int __maybe_unused vic_runtime_resume(struct device *dev)
 {
 	struct vic *vic = dev_get_drvdata(dev);
 	int err;
@@ -310,7 +309,7 @@
 	return err;
 }
 
-static int vic_runtime_suspend(struct device *dev)
+static int __maybe_unused vic_runtime_suspend(struct device *dev)
 {
 	struct vic *vic = dev_get_drvdata(dev);
 	int err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tidss/tidss_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tidss/tidss_crtc.c
@@ -172,13 +172,13 @@
 	struct tidss_device *tidss = to_tidss(ddev);
 	unsigned long flags;
 
-	dev_dbg(ddev->dev,
-		"%s: %s enabled %d, needs modeset %d, event %p\n", __func__,
-		crtc->name, drm_atomic_crtc_needs_modeset(crtc->state),
-		crtc->state->enable, crtc->state->event);
+	dev_dbg(ddev->dev, "%s: %s is %sactive, %s modeset, event %p\n",
+		__func__, crtc->name, crtc->state->active ? "" : "not ",
+		drm_atomic_crtc_needs_modeset(crtc->state) ? "needs" : "doesn't need",
+		crtc->state->event);
 
 	/* There is nothing to do if CRTC is not going to be enabled. */
-	if (!crtc->state->enable)
+	if (!crtc->state->active)
 		return;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tidss/tidss_dispc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tidss/tidss_dispc.c
@@ -596,7 +596,7 @@
 {
 	dispc_irq_t old_mask = dispc_k2g_read_irqenable(dispc);
 
-	/* clear the irqstatus for newly enabled irqs */
+	/* clear the irqstatus for irqs that will be enabled */
 	dispc_k2g_clear_irqstatus(dispc, (mask ^ old_mask) & mask);
 
 	dispc_k2g_vp_set_irqenable(dispc, 0, mask);
@@ -604,6 +604,9 @@
 
 	dispc_write(dispc, DISPC_IRQENABLE_SET, (1 << 0) | (1 << 7));
 
+	/* clear the irqstatus for irqs that were disabled */
+	dispc_k2g_clear_irqstatus(dispc, (mask ^ old_mask) & old_mask);
+
 	/* flush posted write */
 	dispc_k2g_read_irqenable(dispc);
 }
@@ -676,24 +679,20 @@
 void dispc_k3_clear_irqstatus(struct dispc_device *dispc, dispc_irq_t clearmask)
 {
 	unsigned int i;
-	u32 top_clear = 0;
 
 	for (i = 0; i < dispc->feat->num_vps; ++i) {
-		if (clearmask & DSS_IRQ_VP_MASK(i)) {
+		if (clearmask & DSS_IRQ_VP_MASK(i))
 			dispc_k3_vp_write_irqstatus(dispc, i, clearmask);
-			top_clear |= BIT(i);
-		}
 	}
 	for (i = 0; i < dispc->feat->num_planes; ++i) {
-		if (clearmask & DSS_IRQ_PLANE_MASK(i)) {
+		if (clearmask & DSS_IRQ_PLANE_MASK(i))
 			dispc_k3_vid_write_irqstatus(dispc, i, clearmask);
-			top_clear |= BIT(4 + i);
-		}
 	}
 	if (dispc->feat->subrev == DISPC_K2G)
 		return;
 
-	dispc_write(dispc, DISPC_IRQSTATUS, top_clear);
+	/* always clear the top level irqstatus */
+	dispc_write(dispc, DISPC_IRQSTATUS, dispc_read(dispc, DISPC_IRQSTATUS));
 
 	/* Flush posted writes */
 	dispc_read(dispc, DISPC_IRQSTATUS);
@@ -739,7 +738,7 @@
 
 	old_mask = dispc_k3_read_irqenable(dispc);
 
-	/* clear the irqstatus for newly enabled irqs */
+	/* clear the irqstatus for irqs that will be enabled */
 	dispc_k3_clear_irqstatus(dispc, (old_mask ^ mask) & mask);
 
 	for (i = 0; i < dispc->feat->num_vps; ++i) {
@@ -764,6 +763,9 @@
 	if (main_disable)
 		dispc_write(dispc, DISPC_IRQENABLE_CLR, main_disable);
 
+	/* clear the irqstatus for irqs that were disabled */
+	dispc_k3_clear_irqstatus(dispc, (old_mask ^ mask) & old_mask);
+
 	/* Flush posted writes */
 	dispc_read(dispc, DISPC_IRQENABLE_SET);
 }
@@ -1855,8 +1857,8 @@
 	{ DRM_FORMAT_XBGR4444, 0x21, },
 	{ DRM_FORMAT_RGBX4444, 0x22, },
 
-	{ DRM_FORMAT_ARGB1555, 0x25, },
-	{ DRM_FORMAT_ABGR1555, 0x26, },
+	{ DRM_FORMAT_XRGB1555, 0x25, },
+	{ DRM_FORMAT_XBGR1555, 0x26, },
 
 	{ DRM_FORMAT_XRGB8888, 0x27, },
 	{ DRM_FORMAT_XBGR8888, 0x28, },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tidss/tidss_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tidss/tidss_kms.c
@@ -4,8 +4,6 @@
  * Author: Tomi Valkeinen <tomi.valkeinen@ti.com>
  */
 
-#include <linux/dma-fence.h>
-
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_bridge.h>
@@ -28,7 +26,6 @@
 {
 	struct drm_device *ddev = old_state->dev;
 	struct tidss_device *tidss = to_tidss(ddev);
-	bool fence_cookie = dma_fence_begin_signalling();
 
 	dev_dbg(ddev->dev, "%s\n", __func__);
 
@@ -39,7 +36,6 @@
 	drm_atomic_helper_commit_modeset_enables(ddev, old_state);
 
 	drm_atomic_helper_commit_hw_done(old_state);
-	dma_fence_end_signalling(fence_cookie);
 	drm_atomic_helper_wait_for_flip_done(ddev, old_state);
 
 	drm_atomic_helper_cleanup_planes(ddev, old_state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tidss/tidss_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tidss/tidss_plane.c
@@ -210,7 +210,7 @@
 
 	drm_plane_helper_add(&tplane->plane, &tidss_plane_helper_funcs);
 
-	drm_plane_create_zpos_property(&tplane->plane, hw_plane_id, 0,
+	drm_plane_create_zpos_property(&tplane->plane, tidss->num_planes, 0,
 				       num_planes - 1);
 
 	ret = drm_plane_create_color_properties(&tplane->plane,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tilcdc/tilcdc_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tilcdc/tilcdc_drv.c
@@ -140,7 +140,7 @@
 	if (ret)
 		return ret;
 
-	priv->irq_enabled = false;
+	priv->irq_enabled = true;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tilcdc/tilcdc_external.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tilcdc/tilcdc_external.c
@@ -60,11 +60,13 @@
 int tilcdc_add_component_encoder(struct drm_device *ddev)
 {
 	struct tilcdc_drm_private *priv = ddev->dev_private;
-	struct drm_encoder *encoder;
+	struct drm_encoder *encoder = NULL, *iter;
 
-	list_for_each_entry(encoder, &ddev->mode_config.encoder_list, head)
-		if (encoder->possible_crtcs & (1 << priv->crtc->index))
+	list_for_each_entry(iter, &ddev->mode_config.encoder_list, head)
+		if (iter->possible_crtcs & (1 << priv->crtc->index)) {
+			encoder = iter;
 			break;
+		}
 
 	if (!encoder) {
 		dev_err(ddev->dev, "%s: No suitable encoder found\n", __func__);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tiny/bochs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tiny/bochs.c
@@ -305,6 +305,8 @@
 static void bochs_hw_blank(struct bochs_device *bochs, bool blank)
 {
 	DRM_DEBUG_DRIVER("hw_blank %d\n", blank);
+	/* enable color bit (so VGA_IS1_RC access works) */
+	bochs_vga_writeb(bochs, VGA_MIS_W, VGA_MIS_COLOR);
 	/* discard ar_flip_flop */
 	(void)bochs_vga_readb(bochs, VGA_IS1_RC);
 	/* blank or unblank; we need only update index and set 0x20 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tiny/cirrus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tiny/cirrus.c
@@ -450,7 +450,7 @@
 	if (state->fb && cirrus->cpp != cirrus_cpp(state->fb))
 		cirrus_mode_set(cirrus, &crtc->mode, state->fb);
 
-	if (drm_atomic_helper_damage_merged(old_state, state, &rect))
+	if (state->fb && drm_atomic_helper_damage_merged(old_state, state, &rect))
 		cirrus_fb_blit_rect(state->fb, &shadow_plane_state->data[0], &rect);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tiny/gm12u320.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tiny/gm12u320.c
@@ -67,10 +67,10 @@
 #define READ_STATUS_SIZE		13
 #define MISC_VALUE_SIZE			4
 
-#define CMD_TIMEOUT			msecs_to_jiffies(200)
-#define DATA_TIMEOUT			msecs_to_jiffies(1000)
-#define IDLE_TIMEOUT			msecs_to_jiffies(2000)
-#define FIRST_FRAME_TIMEOUT		msecs_to_jiffies(2000)
+#define CMD_TIMEOUT			200
+#define DATA_TIMEOUT			1000
+#define IDLE_TIMEOUT			2000
+#define FIRST_FRAME_TIMEOUT		2000
 
 #define MISC_REQ_GET_SET_ECO_A		0xff
 #define MISC_REQ_GET_SET_ECO_B		0x35
@@ -386,7 +386,7 @@
 	 * switches back to showing its logo.
 	 */
 	queue_delayed_work(system_long_wq, &gm12u320->fb_update.work,
-			   IDLE_TIMEOUT);
+			   msecs_to_jiffies(IDLE_TIMEOUT));
 
 	return;
 err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tiny/ili9486.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tiny/ili9486.c
@@ -43,6 +43,7 @@
 			     size_t num)
 {
 	struct spi_device *spi = mipi->spi;
+	unsigned int bpw = 8;
 	void *data = par;
 	u32 speed_hz;
 	int i, ret;
@@ -56,8 +57,6 @@
 	 * The displays are Raspberry Pi HATs and connected to the 8-bit only
 	 * SPI controller, so 16-bit command and parameters need byte swapping
 	 * before being transferred as 8-bit on the big endian SPI bus.
-	 * Pixel data bytes have already been swapped before this function is
-	 * called.
 	 */
 	buf[0] = cpu_to_be16(*cmd);
 	gpiod_set_value_cansleep(mipi->dc, 0);
@@ -71,12 +70,18 @@
 		for (i = 0; i < num; i++)
 			buf[i] = cpu_to_be16(par[i]);
 		num *= 2;
-		speed_hz = mipi_dbi_spi_cmd_max_speed(spi, num);
 		data = buf;
 	}
 
+	/*
+	 * Check whether pixel data bytes needs to be swapped or not
+	 */
+	if (*cmd == MIPI_DCS_WRITE_MEMORY_START && !mipi->swap_bytes)
+		bpw = 16;
+
 	gpiod_set_value_cansleep(mipi->dc, 1);
-	ret = mipi_dbi_spi_transfer(spi, speed_hz, 8, data, num);
+	speed_hz = mipi_dbi_spi_cmd_max_speed(spi, num);
+	ret = mipi_dbi_spi_transfer(spi, speed_hz, bpw, data, num);
  free:
 	kfree(buf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tiny/simpledrm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tiny/simpledrm.c
@@ -458,7 +458,7 @@
 {
 	struct drm_display_mode mode = { SIMPLEDRM_MODE(width, height) };
 
-	mode.clock = 60 /* Hz */ * mode.hdisplay * mode.vdisplay;
+	mode.clock = mode.hdisplay * mode.vdisplay * 60 / 1000 /* kHz */;
 	drm_mode_set_name(&mode);
 
 	return mode;
@@ -614,7 +614,7 @@
 	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
 };
 
-static int
+static enum drm_mode_status
 simpledrm_simple_display_pipe_mode_valid(struct drm_simple_display_pipe *pipe,
 				    const struct drm_display_mode *mode)
 {
@@ -779,6 +779,9 @@
 	if (ret)
 		return ret;
 	drm_connector_helper_add(connector, &simpledrm_connector_helper_funcs);
+	drm_connector_set_panel_orientation_with_quirk(connector,
+						       DRM_MODE_PANEL_ORIENTATION_UNKNOWN,
+						       mode->hdisplay, mode->vdisplay);
 
 	formats = simpledrm_device_formats(sdev, &nformats);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/tiny/st7735r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/tiny/st7735r.c
@@ -174,6 +174,7 @@
 
 static const struct spi_device_id st7735r_id[] = {
 	{ "jd-t18003-t01", (uintptr_t)&jd_t18003_t01_cfg },
+	{ "rh128128t", (uintptr_t)&rh128128t_cfg },
 	{ },
 };
 MODULE_DEVICE_TABLE(spi, st7735r_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_bo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_bo.c
@@ -552,17 +552,18 @@
 		goto out;
 	}
 
-bounce:
-	ret = ttm_bo_handle_move_mem(bo, evict_mem, true, ctx, &hop);
-	if (ret == -EMULTIHOP) {
+	do {
+		ret = ttm_bo_handle_move_mem(bo, evict_mem, true, ctx, &hop);
+		if (ret != -EMULTIHOP)
+			break;
+
 		ret = ttm_bo_bounce_temp_buffer(bo, &evict_mem, ctx, &hop);
-		if (ret) {
+	} while (!ret);
+
+	if (ret) {
+		ttm_resource_free(bo, &evict_mem);
+		if (ret != -ERESTARTSYS && ret != -EINTR)
 			pr_err("Buffer eviction failed\n");
-			ttm_resource_free(bo, &evict_mem);
-			goto out;
-		}
-		/* try and move to final place now. */
-		goto bounce;
 	}
 out:
 	return ret;
@@ -603,6 +604,13 @@
 {
 	bool ret = false;
 
+	if (bo->pin_count) {
+		*locked = false;
+		if (busy)
+			*busy = false;
+		return false;
+	}
+
 	if (bo->base.resv == ctx->resv) {
 		dma_resv_assert_held(bo->base.resv);
 		if (ctx->allow_res_evict)
@@ -724,6 +732,8 @@
 	ret = ttm_bo_evict(bo, ctx);
 	if (locked)
 		ttm_bo_unreserve(bo);
+	else
+		ttm_bo_move_to_lru_tail_unlocked(bo);
 
 	ttm_bo_put(bo);
 	return ret;
@@ -985,7 +995,7 @@
 	/*
 	 * We might need to add a TTM.
 	 */
-	if (bo->resource->mem_type == TTM_PL_SYSTEM) {
+	if (!bo->resource || bo->resource->mem_type == TTM_PL_SYSTEM) {
 		ret = ttm_tt_create(bo, true);
 		if (ret)
 			return ret;
@@ -1185,6 +1195,7 @@
 		ret = ttm_bo_handle_move_mem(bo, evict_mem, true, &ctx, &hop);
 		if (unlikely(ret != 0)) {
 			WARN(ret == -EMULTIHOP, "Unexpected multihop in swaput - likely driver bug.\n");
+			ttm_resource_free(bo, &evict_mem);
 			goto out;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_bo_vm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_bo_vm.c
@@ -171,89 +171,6 @@
 }
 EXPORT_SYMBOL(ttm_bo_vm_reserve);
 
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-/**
- * ttm_bo_vm_insert_huge - Insert a pfn for PUD or PMD faults
- * @vmf: Fault data
- * @bo: The buffer object
- * @page_offset: Page offset from bo start
- * @fault_page_size: The size of the fault in pages.
- * @pgprot: The page protections.
- * Does additional checking whether it's possible to insert a PUD or PMD
- * pfn and performs the insertion.
- *
- * Return: VM_FAULT_NOPAGE on successful insertion, VM_FAULT_FALLBACK if
- * a huge fault was not possible, or on insertion error.
- */
-static vm_fault_t ttm_bo_vm_insert_huge(struct vm_fault *vmf,
-					struct ttm_buffer_object *bo,
-					pgoff_t page_offset,
-					pgoff_t fault_page_size,
-					pgprot_t pgprot)
-{
-	pgoff_t i;
-	vm_fault_t ret;
-	unsigned long pfn;
-	pfn_t pfnt;
-	struct ttm_tt *ttm = bo->ttm;
-	bool write = vmf->flags & FAULT_FLAG_WRITE;
-
-	/* Fault should not cross bo boundary. */
-	page_offset &= ~(fault_page_size - 1);
-	if (page_offset + fault_page_size > bo->resource->num_pages)
-		goto out_fallback;
-
-	if (bo->resource->bus.is_iomem)
-		pfn = ttm_bo_io_mem_pfn(bo, page_offset);
-	else
-		pfn = page_to_pfn(ttm->pages[page_offset]);
-
-	/* pfn must be fault_page_size aligned. */
-	if ((pfn & (fault_page_size - 1)) != 0)
-		goto out_fallback;
-
-	/* Check that memory is contiguous. */
-	if (!bo->resource->bus.is_iomem) {
-		for (i = 1; i < fault_page_size; ++i) {
-			if (page_to_pfn(ttm->pages[page_offset + i]) != pfn + i)
-				goto out_fallback;
-		}
-	} else if (bo->bdev->funcs->io_mem_pfn) {
-		for (i = 1; i < fault_page_size; ++i) {
-			if (ttm_bo_io_mem_pfn(bo, page_offset + i) != pfn + i)
-				goto out_fallback;
-		}
-	}
-
-	pfnt = __pfn_to_pfn_t(pfn, PFN_DEV);
-	if (fault_page_size == (HPAGE_PMD_SIZE >> PAGE_SHIFT))
-		ret = vmf_insert_pfn_pmd_prot(vmf, pfnt, pgprot, write);
-#ifdef CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD
-	else if (fault_page_size == (HPAGE_PUD_SIZE >> PAGE_SHIFT))
-		ret = vmf_insert_pfn_pud_prot(vmf, pfnt, pgprot, write);
-#endif
-	else
-		WARN_ON_ONCE(ret = VM_FAULT_FALLBACK);
-
-	if (ret != VM_FAULT_NOPAGE)
-		goto out_fallback;
-
-	return VM_FAULT_NOPAGE;
-out_fallback:
-	count_vm_event(THP_FAULT_FALLBACK);
-	return VM_FAULT_FALLBACK;
-}
-#else
-static vm_fault_t ttm_bo_vm_insert_huge(struct vm_fault *vmf,
-					struct ttm_buffer_object *bo,
-					pgoff_t page_offset,
-					pgoff_t fault_page_size,
-					pgprot_t pgprot)
-{
-	return VM_FAULT_FALLBACK;
-}
-#endif
-
 /**
  * ttm_bo_vm_fault_reserved - TTM fault helper
  * @vmf: The struct vm_fault given as argument to the fault callback
@@ -261,7 +178,6 @@
  * @num_prefault: Maximum number of prefault pages. The caller may want to
  * specify this based on madvice settings and the size of the GPU object
  * backed by the memory.
- * @fault_page_size: The size of the fault in pages.
  *
  * This function inserts one or more page table entries pointing to the
  * memory backing the buffer object, and then returns a return code
@@ -275,8 +191,7 @@
  */
 vm_fault_t ttm_bo_vm_fault_reserved(struct vm_fault *vmf,
 				    pgprot_t prot,
-				    pgoff_t num_prefault,
-				    pgoff_t fault_page_size)
+				    pgoff_t num_prefault)
 {
 	struct vm_area_struct *vma = vmf->vma;
 	struct ttm_buffer_object *bo = vma->vm_private_data;
@@ -327,11 +242,6 @@
 		prot = pgprot_decrypted(prot);
 	}
 
-	/* We don't prefault on huge faults. Yet. */
-	if (IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE) && fault_page_size != 1)
-		return ttm_bo_vm_insert_huge(vmf, bo, page_offset,
-					     fault_page_size, prot);
-
 	/*
 	 * Speculatively prefault a number of pages. Only error on
 	 * first page.
@@ -429,7 +339,7 @@
 
 	prot = vma->vm_page_prot;
 	if (drm_dev_enter(ddev, &idx)) {
-		ret = ttm_bo_vm_fault_reserved(vmf, prot, TTM_BO_VM_NUM_PREFAULT, 1);
+		ret = ttm_bo_vm_fault_reserved(vmf, prot, TTM_BO_VM_NUM_PREFAULT);
 		drm_dev_exit(idx);
 	} else {
 		ret = ttm_bo_vm_dummy_page(vmf, prot);
@@ -519,11 +429,6 @@
 
 	switch (bo->resource->mem_type) {
 	case TTM_PL_SYSTEM:
-		if (unlikely(bo->ttm->page_flags & TTM_PAGE_FLAG_SWAPPED)) {
-			ret = ttm_tt_swapin(bo->ttm);
-			if (unlikely(ret != 0))
-				return ret;
-		}
 		fallthrough;
 	case TTM_PL_TT:
 		ret = ttm_bo_vm_access_kmap(bo, offset, buf, len, write);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_device.c
@@ -234,10 +234,6 @@
 	struct ttm_resource_manager *man;
 	unsigned i;
 
-	man = ttm_manager_type(bdev, TTM_PL_SYSTEM);
-	ttm_resource_manager_set_used(man, false);
-	ttm_set_driver_manager(bdev, TTM_PL_SYSTEM, NULL);
-
 	mutex_lock(&ttm_global_mutex);
 	list_del(&bdev->device_list);
 	mutex_unlock(&ttm_global_mutex);
@@ -247,6 +243,10 @@
 	if (ttm_bo_delayed_delete(bdev, true))
 		pr_debug("Delayed destroy list was clean\n");
 
+	man = ttm_manager_type(bdev, TTM_PL_SYSTEM);
+	ttm_resource_manager_set_used(man, false);
+	ttm_set_driver_manager(bdev, TTM_PL_SYSTEM, NULL);
+
 	spin_lock(&bdev->lru_lock);
 	for (i = 0; i < TTM_MAX_BO_PRIORITY; ++i)
 		if (list_empty(&man->lru[0]))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_pool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_pool.c
@@ -345,6 +345,65 @@
 	return p->private;
 }
 
+/* Called when we got a page, either from a pool or newly allocated */
+static int ttm_pool_page_allocated(struct ttm_pool *pool, unsigned int order,
+				   struct page *p, dma_addr_t **dma_addr,
+				   unsigned long *num_pages,
+				   struct page ***pages)
+{
+	unsigned int i;
+	int r;
+
+	if (*dma_addr) {
+		r = ttm_pool_map(pool, order, p, dma_addr);
+		if (r)
+			return r;
+	}
+
+	*num_pages -= 1 << order;
+	for (i = 1 << order; i; --i, ++(*pages), ++p)
+		**pages = p;
+
+	return 0;
+}
+
+/**
+ * ttm_pool_free_range() - Free a range of TTM pages
+ * @pool: The pool used for allocating.
+ * @tt: The struct ttm_tt holding the page pointers.
+ * @caching: The page caching mode used by the range.
+ * @start_page: index for first page to free.
+ * @end_page: index for last page to free + 1.
+ *
+ * During allocation the ttm_tt page-vector may be populated with ranges of
+ * pages with different attributes if allocation hit an error without being
+ * able to completely fulfill the allocation. This function can be used
+ * to free these individual ranges.
+ */
+static void ttm_pool_free_range(struct ttm_pool *pool, struct ttm_tt *tt,
+				enum ttm_caching caching,
+				pgoff_t start_page, pgoff_t end_page)
+{
+	struct page **pages = &tt->pages[start_page];
+	unsigned int order;
+	pgoff_t i, nr;
+
+	for (i = start_page; i < end_page; i += nr, pages += nr) {
+		struct ttm_pool_type *pt = NULL;
+
+		order = ttm_pool_page_order(pool, *pages);
+		nr = (1UL << order);
+		if (tt->dma_address)
+			ttm_pool_unmap(pool, tt->dma_address[i], nr);
+
+		pt = ttm_pool_select_type(pool, caching, order);
+		if (pt)
+			ttm_pool_type_give(pt, *pages);
+		else
+			ttm_pool_free_page(pool, caching, order, *pages);
+	}
+}
+
 /**
  * ttm_pool_alloc - Fill a ttm_tt object
  *
@@ -360,12 +419,14 @@
 int ttm_pool_alloc(struct ttm_pool *pool, struct ttm_tt *tt,
 		   struct ttm_operation_ctx *ctx)
 {
-	unsigned long num_pages = tt->num_pages;
+	pgoff_t num_pages = tt->num_pages;
 	dma_addr_t *dma_addr = tt->dma_address;
 	struct page **caching = tt->pages;
 	struct page **pages = tt->pages;
+	enum ttm_caching page_caching;
 	gfp_t gfp_flags = GFP_USER;
-	unsigned int i, order;
+	pgoff_t caching_divide;
+	unsigned int order;
 	struct page *p;
 	int r;
 
@@ -386,45 +447,61 @@
 	for (order = min_t(unsigned int, MAX_ORDER - 1, __fls(num_pages));
 	     num_pages;
 	     order = min_t(unsigned int, order, __fls(num_pages))) {
-		bool apply_caching = false;
 		struct ttm_pool_type *pt;
 
+		page_caching = tt->caching;
 		pt = ttm_pool_select_type(pool, tt->caching, order);
 		p = pt ? ttm_pool_type_take(pt) : NULL;
 		if (p) {
-			apply_caching = true;
-		} else {
-			p = ttm_pool_alloc_page(pool, gfp_flags, order);
-			if (p && PageHighMem(p))
-				apply_caching = true;
-		}
-
-		if (!p) {
-			if (order) {
-				--order;
-				continue;
-			}
-			r = -ENOMEM;
-			goto error_free_all;
-		}
-
-		if (apply_caching) {
 			r = ttm_pool_apply_caching(caching, pages,
 						   tt->caching);
 			if (r)
 				goto error_free_page;
-			caching = pages + (1 << order);
+
+			caching = pages;
+			do {
+				r = ttm_pool_page_allocated(pool, order, p,
+							    &dma_addr,
+							    &num_pages,
+							    &pages);
+				if (r)
+					goto error_free_page;
+
+				caching = pages;
+				if (num_pages < (1 << order))
+					break;
+
+				p = ttm_pool_type_take(pt);
+			} while (p);
 		}
 
-		if (dma_addr) {
-			r = ttm_pool_map(pool, order, p, &dma_addr);
+		page_caching = ttm_cached;
+		while (num_pages >= (1 << order) &&
+		       (p = ttm_pool_alloc_page(pool, gfp_flags, order))) {
+
+			if (PageHighMem(p)) {
+				r = ttm_pool_apply_caching(caching, pages,
+							   tt->caching);
+				if (r)
+					goto error_free_page;
+				caching = pages;
+			}
+			r = ttm_pool_page_allocated(pool, order, p, &dma_addr,
+						    &num_pages, &pages);
 			if (r)
 				goto error_free_page;
+			if (PageHighMem(p))
+				caching = pages;
 		}
 
-		num_pages -= 1 << order;
-		for (i = 1 << order; i; --i)
-			*(pages++) = p++;
+		if (!p) {
+			if (order) {
+				--order;
+				continue;
+			}
+			r = -ENOMEM;
+			goto error_free_all;
+		}
 	}
 
 	r = ttm_pool_apply_caching(caching, pages, tt->caching);
@@ -434,15 +511,13 @@
 	return 0;
 
 error_free_page:
-	ttm_pool_free_page(pool, tt->caching, order, p);
+	ttm_pool_free_page(pool, page_caching, order, p);
 
 error_free_all:
 	num_pages = tt->num_pages - num_pages;
-	for (i = 0; i < num_pages; ) {
-		order = ttm_pool_page_order(pool, tt->pages[i]);
-		ttm_pool_free_page(pool, tt->caching, order, tt->pages[i]);
-		i += 1 << order;
-	}
+	caching_divide = caching - tt->pages;
+	ttm_pool_free_range(pool, tt, tt->caching, 0, caching_divide);
+	ttm_pool_free_range(pool, tt, ttm_cached, caching_divide, num_pages);
 
 	return r;
 }
@@ -458,27 +533,7 @@
  */
 void ttm_pool_free(struct ttm_pool *pool, struct ttm_tt *tt)
 {
-	unsigned int i;
-
-	for (i = 0; i < tt->num_pages; ) {
-		struct page *p = tt->pages[i];
-		unsigned int order, num_pages;
-		struct ttm_pool_type *pt;
-
-		order = ttm_pool_page_order(pool, p);
-		num_pages = 1ULL << order;
-		if (tt->dma_address)
-			ttm_pool_unmap(pool, tt->dma_address[i], num_pages);
-
-		pt = ttm_pool_select_type(pool, tt->caching, order);
-		if (pt)
-			ttm_pool_type_give(pt, tt->pages[i]);
-		else
-			ttm_pool_free_page(pool, tt->caching, order,
-					   tt->pages[i]);
-
-		i += num_pages;
-	}
+	ttm_pool_free_range(pool, tt, tt->caching, 0, tt->num_pages);
 
 	while (atomic_long_read(&allocated_pages) > page_pool_size)
 		ttm_pool_shrink();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_range_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_range_manager.c
@@ -89,6 +89,7 @@
 	spin_unlock(&rman->lock);
 
 	if (unlikely(ret)) {
+		ttm_resource_fini(man, *res);
 		kfree(node);
 		return ret;
 	}
@@ -108,6 +109,7 @@
 	drm_mm_remove_node(&node->mm_nodes[0]);
 	spin_unlock(&rman->lock);
 
+	ttm_resource_fini(man, res);
 	kfree(node);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_resource.c
@@ -29,6 +29,14 @@
 #include <drm/ttm/ttm_resource.h>
 #include <drm/ttm/ttm_bo_driver.h>
 
+/**
+ * ttm_resource_init - resource object constructure
+ * @bo: buffer object this resources is allocated for
+ * @place: placement of the resource
+ * @res: the resource object to inistilize
+ *
+ * Initialize a new resource object. Counterpart of &ttm_resource_fini.
+ */
 void ttm_resource_init(struct ttm_buffer_object *bo,
                        const struct ttm_place *place,
                        struct ttm_resource *res)
@@ -44,6 +52,21 @@
 }
 EXPORT_SYMBOL(ttm_resource_init);
 
+/**
+ * ttm_resource_fini - resource destructor
+ * @man: the resource manager this resource belongs to
+ * @res: the resource to clean up
+ *
+ * Should be used by resource manager backends to clean up the TTM resource
+ * objects before freeing the underlying structure. Counterpart of
+ * &ttm_resource_init
+ */
+void ttm_resource_fini(struct ttm_resource_manager *man,
+		       struct ttm_resource *res)
+{
+}
+EXPORT_SYMBOL(ttm_resource_fini);
+
 int ttm_resource_alloc(struct ttm_buffer_object *bo,
 		       const struct ttm_place *place,
 		       struct ttm_resource **res_ptr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/ttm/ttm_sys_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/ttm/ttm_sys_manager.c
@@ -23,6 +23,7 @@
 static void ttm_sys_man_free(struct ttm_resource_manager *man,
 			     struct ttm_resource *res)
 {
+	ttm_resource_fini(man, res);
 	kfree(res);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/udl/udl_connector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/udl/udl_connector.c
@@ -30,7 +30,7 @@
 		int bval = (i + block * EDID_LENGTH) << 8;
 		ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				      0x02, (0x80 | (0x02 << 5)), bval,
-				      0xA1, read_buff, 2, HZ);
+				      0xA1, read_buff, 2, 1000);
 		if (ret < 1) {
 			DRM_ERROR("Read EDID byte %d failed err %x\n", i, ret);
 			kfree(read_buff);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/udl/udl_modeset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/udl/udl_modeset.c
@@ -381,9 +381,6 @@
 
 	udl_handle_damage(fb, &shadow_plane_state->data[0], 0, 0, fb->width, fb->height);
 
-	if (!crtc_state->mode_changed)
-		return;
-
 	/* enable display */
 	udl_crtc_write_mode_to_hw(crtc);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_bo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_bo.c
@@ -47,18 +47,18 @@
 	/* GPU execution may have dirtied any pages in the BO. */
 	bo->base.pages_mark_dirty_on_put = true;
 
-	drm_gem_shmem_free_object(obj);
+	drm_gem_shmem_free(&bo->base);
 }
 
 static const struct drm_gem_object_funcs v3d_gem_funcs = {
 	.free = v3d_free_object,
-	.print_info = drm_gem_shmem_print_info,
-	.pin = drm_gem_shmem_pin,
-	.unpin = drm_gem_shmem_unpin,
-	.get_sg_table = drm_gem_shmem_get_sg_table,
-	.vmap = drm_gem_shmem_vmap,
-	.vunmap = drm_gem_shmem_vunmap,
-	.mmap = drm_gem_shmem_mmap,
+	.print_info = drm_gem_shmem_object_print_info,
+	.pin = drm_gem_shmem_object_pin,
+	.unpin = drm_gem_shmem_object_unpin,
+	.get_sg_table = drm_gem_shmem_object_get_sg_table,
+	.vmap = drm_gem_shmem_object_vmap,
+	.vunmap = drm_gem_shmem_object_vunmap,
+	.mmap = drm_gem_shmem_object_mmap,
 };
 
 /* gem_create_object function for allocating a BO struct and doing
@@ -95,7 +95,7 @@
 	/* So far we pin the BO in the MMU for its lifetime, so use
 	 * shmem's helper for getting a lifetime sgt.
 	 */
-	sgt = drm_gem_shmem_get_pages_sgt(&bo->base.base);
+	sgt = drm_gem_shmem_get_pages_sgt(&bo->base);
 	if (IS_ERR(sgt))
 		return PTR_ERR(sgt);
 
@@ -141,7 +141,7 @@
 	return bo;
 
 free_obj:
-	drm_gem_shmem_free_object(&shmem_obj->base);
+	drm_gem_shmem_free(shmem_obj);
 	return ERR_PTR(ret);
 }
 
@@ -159,7 +159,7 @@
 
 	ret = v3d_bo_create_finish(obj);
 	if (ret) {
-		drm_gem_shmem_free_object(obj);
+		drm_gem_shmem_free(&to_v3d_bo(obj)->base);
 		return ERR_PTR(ret);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_drv.c
@@ -221,6 +221,7 @@
 	int ret;
 	u32 mmu_debug;
 	u32 ident1;
+	u64 mask;
 
 
 	v3d = devm_drm_dev_alloc(dev, &v3d_drm_driver, struct v3d_dev, drm);
@@ -240,8 +241,11 @@
 		return ret;
 
 	mmu_debug = V3D_READ(V3D_MMU_DEBUG_INFO);
-	dma_set_mask_and_coherent(dev,
-		DMA_BIT_MASK(30 + V3D_GET_FIELD(mmu_debug, V3D_MMU_PA_WIDTH)));
+	mask = DMA_BIT_MASK(30 + V3D_GET_FIELD(mmu_debug, V3D_MMU_PA_WIDTH));
+	ret = dma_set_mask_and_coherent(dev, mask);
+	if (ret)
+		return ret;
+
 	v3d->va_width = 30 + V3D_GET_FIELD(mmu_debug, V3D_MMU_VA_WIDTH);
 
 	ident1 = V3D_READ(V3D_HUB_IDENT1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_gem.c
@@ -197,8 +197,8 @@
 
 	V3D_CORE_WRITE(core, V3D_CTL_L2TCACTL, V3D_L2TCACTL_TMUWCF);
 	if (wait_for(!(V3D_CORE_READ(core, V3D_CTL_L2TCACTL) &
-		       V3D_L2TCACTL_L2TFLS), 100)) {
-		DRM_ERROR("Timeout waiting for L1T write combiner flush\n");
+		       V3D_L2TCACTL_TMUWCF), 100)) {
+		DRM_ERROR("Timeout waiting for TMU write combiner flush\n");
 	}
 
 	mutex_lock(&v3d->cache_clean_lock);
@@ -625,7 +625,7 @@
 
 		if (!render->base.perfmon) {
 			ret = -ENOENT;
-			goto fail;
+			goto fail_perfmon;
 		}
 	}
 
@@ -678,6 +678,7 @@
 
 fail_unreserve:
 	mutex_unlock(&v3d->sched_lock);
+fail_perfmon:
 	drm_gem_unlock_reservations(last_job->bo,
 				    last_job->bo_count, &acquire_ctx);
 fail:
@@ -854,7 +855,7 @@
 						     args->perfmon_id);
 		if (!job->base.perfmon) {
 			ret = -ENOENT;
-			goto fail;
+			goto fail_perfmon;
 		}
 	}
 
@@ -886,6 +887,7 @@
 
 fail_unreserve:
 	mutex_unlock(&v3d->sched_lock);
+fail_perfmon:
 	drm_gem_unlock_reservations(clean_job->bo, clean_job->bo_count,
 				    &acquire_ctx);
 fail:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_irq.c
@@ -102,7 +102,10 @@
 			to_v3d_fence(v3d->bin_job->base.irq_fence);
 
 		trace_v3d_bcl_irq(&v3d->drm, fence->seqno);
+
+		v3d->bin_job = NULL;
 		dma_fence_signal(&fence->base);
+
 		status = IRQ_HANDLED;
 	}
 
@@ -111,7 +114,10 @@
 			to_v3d_fence(v3d->render_job->base.irq_fence);
 
 		trace_v3d_rcl_irq(&v3d->drm, fence->seqno);
+
+		v3d->render_job = NULL;
 		dma_fence_signal(&fence->base);
+
 		status = IRQ_HANDLED;
 	}
 
@@ -120,7 +126,10 @@
 			to_v3d_fence(v3d->csd_job->base.irq_fence);
 
 		trace_v3d_csd_irq(&v3d->drm, fence->seqno);
+
+		v3d->csd_job = NULL;
 		dma_fence_signal(&fence->base);
+
 		status = IRQ_HANDLED;
 	}
 
@@ -156,7 +165,10 @@
 			to_v3d_fence(v3d->tfu_job->base.irq_fence);
 
 		trace_v3d_tfu_irq(&v3d->drm, fence->seqno);
+
+		v3d->tfu_job = NULL;
 		dma_fence_signal(&fence->base);
+
 		status = IRQ_HANDLED;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_mmu.c
@@ -34,32 +34,23 @@
 {
 	int ret;
 
-	/* Make sure that another flush isn't already running when we
-	 * start this one.
-	 */
-	ret = wait_for(!(V3D_READ(V3D_MMU_CTL) &
-			 V3D_MMU_CTL_TLB_CLEARING), 100);
-	if (ret)
-		dev_err(v3d->drm.dev, "TLB clear wait idle pre-wait failed\n");
-
-	V3D_WRITE(V3D_MMU_CTL, V3D_READ(V3D_MMU_CTL) |
-		  V3D_MMU_CTL_TLB_CLEAR);
-
-	V3D_WRITE(V3D_MMUC_CONTROL,
-		  V3D_MMUC_CONTROL_FLUSH |
+	V3D_WRITE(V3D_MMUC_CONTROL, V3D_MMUC_CONTROL_FLUSH |
 		  V3D_MMUC_CONTROL_ENABLE);
 
-	ret = wait_for(!(V3D_READ(V3D_MMU_CTL) &
-			 V3D_MMU_CTL_TLB_CLEARING), 100);
+	ret = wait_for(!(V3D_READ(V3D_MMUC_CONTROL) &
+			 V3D_MMUC_CONTROL_FLUSHING), 100);
 	if (ret) {
-		dev_err(v3d->drm.dev, "TLB clear wait idle failed\n");
+		dev_err(v3d->drm.dev, "MMUC flush wait idle failed\n");
 		return ret;
 	}
 
-	ret = wait_for(!(V3D_READ(V3D_MMUC_CONTROL) &
-			 V3D_MMUC_CONTROL_FLUSHING), 100);
+	V3D_WRITE(V3D_MMU_CTL, V3D_READ(V3D_MMU_CTL) |
+		  V3D_MMU_CTL_TLB_CLEAR);
+
+	ret = wait_for(!(V3D_READ(V3D_MMU_CTL) &
+			 V3D_MMU_CTL_TLB_CLEARING), 100);
 	if (ret)
-		dev_err(v3d->drm.dev, "MMUC flush wait idle failed\n");
+		dev_err(v3d->drm.dev, "MMU TLB clear wait idle failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_perfmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_perfmon.c
@@ -25,11 +25,12 @@
 {
 	unsigned int i;
 	u32 mask;
-	u8 ncounters = perfmon->ncounters;
+	u8 ncounters;
 
 	if (WARN_ON_ONCE(!perfmon || v3d->active_perfmon))
 		return;
 
+	ncounters = perfmon->ncounters;
 	mask = GENMASK(ncounters - 1, 0);
 
 	for (i = 0; i < ncounters; i++) {
@@ -48,9 +49,9 @@
 		V3D_CORE_WRITE(0, V3D_V4_PCTR_0_SRC_X(source), channel);
 	}
 
+	V3D_CORE_WRITE(0, V3D_V4_PCTR_0_EN, mask);
 	V3D_CORE_WRITE(0, V3D_V4_PCTR_0_CLR, mask);
 	V3D_CORE_WRITE(0, V3D_PCTR_0_OVERFLOW, mask);
-	V3D_CORE_WRITE(0, V3D_V4_PCTR_0_EN, mask);
 
 	v3d->active_perfmon = perfmon;
 }
@@ -100,6 +101,11 @@
 static int v3d_perfmon_idr_del(int id, void *elem, void *data)
 {
 	struct v3d_perfmon *perfmon = elem;
+	struct v3d_dev *v3d = (struct v3d_dev *)data;
+
+	/* If the active perfmon is being destroyed, stop it first */
+	if (perfmon == v3d->active_perfmon)
+		v3d_perfmon_stop(v3d, perfmon, false);
 
 	v3d_perfmon_put(perfmon);
 
@@ -108,8 +114,10 @@
 
 void v3d_perfmon_close_file(struct v3d_file_priv *v3d_priv)
 {
+	struct v3d_dev *v3d = v3d_priv->v3d;
+
 	mutex_lock(&v3d_priv->perfmon.lock);
-	idr_for_each(&v3d_priv->perfmon.idr, v3d_perfmon_idr_del, NULL);
+	idr_for_each(&v3d_priv->perfmon.idr, v3d_perfmon_idr_del, v3d);
 	idr_destroy(&v3d_priv->perfmon.idr);
 	mutex_unlock(&v3d_priv->perfmon.lock);
 }
@@ -167,6 +175,7 @@
 {
 	struct v3d_file_priv *v3d_priv = file_priv->driver_priv;
 	struct drm_v3d_perfmon_destroy *req = data;
+	struct v3d_dev *v3d = v3d_priv->v3d;
 	struct v3d_perfmon *perfmon;
 
 	mutex_lock(&v3d_priv->perfmon.lock);
@@ -176,6 +185,10 @@
 	if (!perfmon)
 		return -EINVAL;
 
+	/* If the active perfmon is being destroyed, stop it first */
+	if (perfmon == v3d->active_perfmon)
+		v3d_perfmon_stop(v3d, perfmon, false);
+
 	v3d_perfmon_put(perfmon);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/v3d/v3d_sched.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/v3d/v3d_sched.c
@@ -202,11 +202,15 @@
 	struct drm_device *dev = &v3d->drm;
 	struct dma_fence *fence;
 
+	if (unlikely(job->base.base.s_fence->finished.error))
+		return NULL;
+
+	v3d->tfu_job = job;
+
 	fence = v3d_fence_create(v3d, V3D_TFU);
 	if (IS_ERR(fence))
 		return NULL;
 
-	v3d->tfu_job = job;
 	if (job->base.irq_fence)
 		dma_fence_put(job->base.irq_fence);
 	job->base.irq_fence = dma_fence_get(fence);
@@ -240,6 +244,9 @@
 	struct dma_fence *fence;
 	int i;
 
+	if (unlikely(job->base.base.s_fence->finished.error))
+		return NULL;
+
 	v3d->csd_job = job;
 
 	v3d_invalidate_caches(v3d);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vboxvideo/hgsmi_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vboxvideo/hgsmi_base.c
@@ -139,7 +139,15 @@
 		flags |= VBOX_MOUSE_POINTER_VISIBLE;
 	}
 
-	p = hgsmi_buffer_alloc(ctx, sizeof(*p) + pixel_len, HGSMI_CH_VBVA,
+	/*
+	 * The 4 extra bytes come from switching struct vbva_mouse_pointer_shape
+	 * from having a 4 bytes fixed array at the end to using a proper VLA
+	 * at the end. These 4 extra bytes were not subtracted from sizeof(*p)
+	 * before the switch to the VLA, so this way the behavior is unchanged.
+	 * Chances are these 4 extra bytes are not necessary but they are kept
+	 * to avoid regressions.
+	 */
+	p = hgsmi_buffer_alloc(ctx, sizeof(*p) + pixel_len + 4, HGSMI_CH_VBVA,
 			       VBVA_MOUSE_POINTER_SHAPE);
 	if (!p)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vboxvideo/vbox_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vboxvideo/vbox_main.c
@@ -127,8 +127,8 @@
 	/* Create guest-heap mem-pool use 2^4 = 16 byte chunks */
 	vbox->guest_pool = devm_gen_pool_create(vbox->ddev.dev, 4, -1,
 						"vboxvideo-accel");
-	if (!vbox->guest_pool)
-		return -ENOMEM;
+	if (IS_ERR(vbox->guest_pool))
+		return PTR_ERR(vbox->guest_pool);
 
 	ret = gen_pool_add_virt(vbox->guest_pool,
 				(unsigned long)vbox->guest_heap,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vboxvideo/vboxvideo.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vboxvideo/vboxvideo.h
@@ -351,10 +351,8 @@
 	 * Bytes in the gap between the AND and the XOR mask are undefined.
 	 * XOR mask scanlines have no gap between them and size of XOR mask is:
 	 * xor_len = width * 4 * height.
-	 *
-	 * Preallocate 4 bytes for accessing actual data as p->data.
 	 */
-	u8 data[4];
+	u8 data[];
 } __packed;
 
 /* pointer is visible */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/Kconfig
@@ -5,6 +5,7 @@
 	depends on DRM
 	depends on SND && SND_SOC
 	depends on COMMON_CLK
+	depends on PM
 	select DRM_KMS_HELPER
 	select DRM_KMS_CMA_HELPER
 	select DRM_GEM_CMA_HELPER
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_bo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_bo.c
@@ -391,7 +391,7 @@
 
 	bo = kzalloc(sizeof(*bo), GFP_KERNEL);
 	if (!bo)
-		return ERR_PTR(-ENOMEM);
+		return NULL;
 
 	bo->madv = VC4_MADV_WILLNEED;
 	refcount_set(&bo->usecnt, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -32,6 +32,7 @@
 #include <linux/clk.h>
 #include <linux/component.h>
 #include <linux/of_device.h>
+#include <linux/pm_runtime.h>
 
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_helper.h>
@@ -42,6 +43,7 @@
 #include <drm/drm_vblank.h>
 
 #include "vc4_drv.h"
+#include "vc4_hdmi.h"
 #include "vc4_regs.h"
 
 #define HVS_FIFO_LATENCY_PIX	6
@@ -121,7 +123,7 @@
 		*vpos /= 2;
 
 		/* Use hpos to correct for field offset in interlaced mode. */
-		if (VC4_GET_FIELD(val, SCALER_DISPSTATX_FRAME_COUNT) % 2)
+		if (vc4_hvs_get_fifo_frame_count(dev, vc4_crtc_state->assigned_channel) % 2)
 			*hpos += mode->crtc_htotal / 2;
 	}
 
@@ -328,7 +330,8 @@
 	u32 pixel_rep = (mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1;
 	bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
 		       vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
-	u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
+	bool is_dsi1 = vc4_encoder->type == VC4_ENCODER_TYPE_DSI1;
+	u32 format = is_dsi1 ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
 	u8 ppc = pv_data->pixels_per_clock;
 	bool debug_dump_regs = false;
 
@@ -354,7 +357,8 @@
 				 PV_HORZB_HACTIVE));
 
 	CRTC_WRITE(PV_VERTA,
-		   VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
+		   VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end +
+				 interlace,
 				 PV_VERTA_VBP) |
 		   VC4_SET_FIELD(mode->crtc_vsync_end - mode->crtc_vsync_start,
 				 PV_VERTA_VSYNC));
@@ -366,7 +370,7 @@
 	if (interlace) {
 		CRTC_WRITE(PV_VERTA_EVEN,
 			   VC4_SET_FIELD(mode->crtc_vtotal -
-					 mode->crtc_vsync_end - 1,
+					 mode->crtc_vsync_end,
 					 PV_VERTA_VBP) |
 			   VC4_SET_FIELD(mode->crtc_vsync_end -
 					 mode->crtc_vsync_start,
@@ -386,7 +390,7 @@
 			   PV_VCONTROL_CONTINUOUS |
 			   (is_dsi ? PV_VCONTROL_DSI : 0) |
 			   PV_VCONTROL_INTERLACE |
-			   VC4_SET_FIELD(mode->htotal * pixel_rep / 2,
+			   VC4_SET_FIELD(mode->htotal * pixel_rep / (2 * ppc),
 					 PV_VCONTROL_ODD_DELAY));
 		CRTC_WRITE(PV_VSYNCD_EVEN, 0);
 	} else {
@@ -496,8 +500,10 @@
 	enum vc4_encoder_type encoder_type;
 	const struct vc4_pv_data *pv_data;
 	struct drm_encoder *encoder;
+	struct vc4_hdmi *vc4_hdmi;
 	unsigned encoder_sel;
 	int channel;
+	int ret;
 
 	if (!(of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
 				      "brcm,bcm2711-pixelvalve2") ||
@@ -525,7 +531,22 @@
 	if (WARN_ON(!encoder))
 		return 0;
 
-	return vc4_crtc_disable(crtc, encoder, NULL, channel);
+	vc4_hdmi = encoder_to_vc4_hdmi(encoder);
+	ret = pm_runtime_resume_and_get(&vc4_hdmi->pdev->dev);
+	if (ret)
+		return ret;
+
+	ret = vc4_crtc_disable(crtc, encoder, NULL, channel);
+	if (ret)
+		return ret;
+
+	/*
+	 * post_crtc_powerdown will have called pm_runtime_put, so we
+	 * don't need it here otherwise we'll get the reference counting
+	 * wrong.
+	 */
+
+	return 0;
 }
 
 static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
@@ -691,14 +712,14 @@
 	struct drm_crtc *crtc = &vc4_crtc->base;
 	struct drm_device *dev = crtc->dev;
 	struct vc4_dev *vc4 = to_vc4_dev(dev);
-	struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
-	u32 chan = vc4_state->assigned_channel;
+	u32 chan = vc4_crtc->current_hvs_channel;
 	unsigned long flags;
 
 	spin_lock_irqsave(&dev->event_lock, flags);
+	spin_lock(&vc4_crtc->irq_lock);
 	if (vc4_crtc->event &&
-	    (vc4_state->mm.start == HVS_READ(SCALER_DISPLACTX(chan)) ||
-	     vc4_state->feed_txp)) {
+	    (vc4_crtc->current_dlist == HVS_READ(SCALER_DISPLACTX(chan)) ||
+	     vc4_crtc->feeds_txp)) {
 		drm_crtc_send_vblank_event(crtc, vc4_crtc->event);
 		vc4_crtc->event = NULL;
 		drm_crtc_vblank_put(crtc);
@@ -711,6 +732,7 @@
 		 */
 		vc4_hvs_unmask_underrun(dev, chan);
 	}
+	spin_unlock(&vc4_crtc->irq_lock);
 	spin_unlock_irqrestore(&dev->event_lock, flags);
 }
 
@@ -876,7 +898,6 @@
 		return NULL;
 
 	old_vc4_state = to_vc4_crtc_state(crtc->state);
-	vc4_state->feed_txp = old_vc4_state->feed_txp;
 	vc4_state->margins = old_vc4_state->margins;
 	vc4_state->assigned_channel = old_vc4_state->assigned_channel;
 
@@ -937,6 +958,7 @@
 static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
 	.mode_valid = vc4_crtc_mode_valid,
 	.atomic_check = vc4_crtc_atomic_check,
+	.atomic_begin = vc4_hvs_atomic_begin,
 	.atomic_flush = vc4_hvs_atomic_flush,
 	.atomic_enable = vc4_crtc_atomic_enable,
 	.atomic_disable = vc4_crtc_atomic_disable,
@@ -1111,6 +1133,7 @@
 		return PTR_ERR(primary_plane);
 	}
 
+	spin_lock_init(&vc4_crtc->irq_lock);
 	drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
 				  crtc_funcs, NULL);
 	drm_crtc_helper_add(crtc, crtc_helper_funcs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_dpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_dpi.c
@@ -148,35 +148,45 @@
 	}
 	drm_connector_list_iter_end(&conn_iter);
 
-	if (connector && connector->display_info.num_bus_formats) {
-		u32 bus_format = connector->display_info.bus_formats[0];
+	if (connector) {
+		if (connector->display_info.num_bus_formats) {
+			u32 bus_format = connector->display_info.bus_formats[0];
 
-		switch (bus_format) {
-		case MEDIA_BUS_FMT_RGB888_1X24:
-			dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB,
-					       DPI_FORMAT);
-			break;
-		case MEDIA_BUS_FMT_BGR888_1X24:
-			dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB,
-					       DPI_FORMAT);
-			dpi_c |= VC4_SET_FIELD(DPI_ORDER_BGR, DPI_ORDER);
-			break;
-		case MEDIA_BUS_FMT_RGB666_1X24_CPADHI:
-			dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_2,
-					       DPI_FORMAT);
-			break;
-		case MEDIA_BUS_FMT_RGB666_1X18:
-			dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_1,
-					       DPI_FORMAT);
-			break;
-		case MEDIA_BUS_FMT_RGB565_1X16:
-			dpi_c |= VC4_SET_FIELD(DPI_FORMAT_16BIT_565_RGB_3,
-					       DPI_FORMAT);
-			break;
-		default:
-			DRM_ERROR("Unknown media bus format %d\n", bus_format);
-			break;
+			switch (bus_format) {
+			case MEDIA_BUS_FMT_RGB888_1X24:
+				dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB,
+						       DPI_FORMAT);
+				break;
+			case MEDIA_BUS_FMT_BGR888_1X24:
+				dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB,
+						       DPI_FORMAT);
+				dpi_c |= VC4_SET_FIELD(DPI_ORDER_BGR,
+						       DPI_ORDER);
+				break;
+			case MEDIA_BUS_FMT_RGB666_1X24_CPADHI:
+				dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_2,
+						       DPI_FORMAT);
+				break;
+			case MEDIA_BUS_FMT_RGB666_1X18:
+				dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_1,
+						       DPI_FORMAT);
+				break;
+			case MEDIA_BUS_FMT_RGB565_1X16:
+				dpi_c |= VC4_SET_FIELD(DPI_FORMAT_16BIT_565_RGB_1,
+						       DPI_FORMAT);
+				break;
+			default:
+				DRM_ERROR("Unknown media bus format %d\n",
+					  bus_format);
+				break;
+			}
 		}
+
+		if (connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
+			dpi_c |= DPI_PIXEL_CLK_INVERT;
+
+		if (connector->display_info.bus_flags & DRM_BUS_FLAG_DE_LOW)
+			dpi_c |= DPI_OUTPUT_ENABLE_INVERT;
 	} else {
 		/* Default to 24bit if no connector found. */
 		dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, DPI_FORMAT);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_drv.c
@@ -214,6 +214,15 @@
 	}
 }
 
+static const struct of_device_id vc4_dma_range_matches[] = {
+	{ .compatible = "brcm,bcm2711-hvs" },
+	{ .compatible = "brcm,bcm2835-hvs" },
+	{ .compatible = "brcm,bcm2835-v3d" },
+	{ .compatible = "brcm,cygnus-v3d" },
+	{ .compatible = "brcm,vc4-v3d" },
+	{}
+};
+
 static int vc4_drm_bind(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
@@ -231,6 +240,16 @@
 		vc4_drm_driver.driver_features &= ~DRIVER_RENDER;
 	of_node_put(node);
 
+	node = of_find_matching_node_and_match(NULL, vc4_dma_range_matches,
+					       NULL);
+	if (node) {
+		ret = of_dma_configure(dev, node, true);
+		of_node_put(node);
+
+		if (ret)
+			return ret;
+	}
+
 	vc4 = devm_drm_dev_alloc(dev, &vc4_drm_driver, struct vc4_dev, base);
 	if (IS_ERR(vc4))
 		return PTR_ERR(vc4);
@@ -364,7 +383,12 @@
 	if (ret)
 		return ret;
 
-	return platform_driver_register(&vc4_platform_driver);
+	ret = platform_driver_register(&vc4_platform_driver);
+	if (ret)
+		platform_unregister_drivers(component_drivers,
+					    ARRAY_SIZE(component_drivers));
+
+	return ret;
 }
 
 static void __exit vc4_drm_unregister(void)
@@ -378,6 +402,7 @@
 module_exit(vc4_drm_unregister);
 
 MODULE_ALIAS("platform:vc4-drm");
+MODULE_SOFTDEP("pre: snd-soc-hdmi-codec");
 MODULE_DESCRIPTION("Broadcom VC4 DRM Driver");
 MODULE_AUTHOR("Eric Anholt <eric@anholt.net>");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_drv.h
@@ -495,6 +495,33 @@
 	struct drm_pending_vblank_event *event;
 
 	struct debugfs_regset32 regset;
+
+	/**
+	 * @feeds_txp: True if the CRTC feeds our writeback controller.
+	 */
+	bool feeds_txp;
+
+	/**
+	 * @irq_lock: Spinlock protecting the resources shared between
+	 * the atomic code and our vblank handler.
+	 */
+	spinlock_t irq_lock;
+
+	/**
+	 * @current_dlist: Start offset of the display list currently
+	 * set in the HVS for that CRTC. Protected by @irq_lock, and
+	 * copied in vc4_hvs_update_dlist() for the CRTC interrupt
+	 * handler to have access to that value.
+	 */
+	unsigned int current_dlist;
+
+	/**
+	 * @current_hvs_channel: HVS channel currently assigned to the
+	 * CRTC. Protected by @irq_lock, and copied in
+	 * vc4_hvs_atomic_begin() for the CRTC interrupt handler to have
+	 * access to that value.
+	 */
+	unsigned int current_hvs_channel;
 };
 
 static inline struct vc4_crtc *
@@ -521,7 +548,6 @@
 	struct drm_crtc_state base;
 	/* Dlist area for this CRTC configuration. */
 	struct drm_mm_node mm;
-	bool feed_txp;
 	bool txp_armed;
 	unsigned int assigned_channel;
 
@@ -907,7 +933,9 @@
 extern struct platform_driver vc4_hvs_driver;
 void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
 int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output);
+u8 vc4_hvs_get_fifo_frame_count(struct drm_device *dev, unsigned int fifo);
 int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_atomic_state *state);
+void vc4_hvs_atomic_begin(struct drm_crtc *crtc, struct drm_atomic_state *state);
 void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_atomic_state *state);
 void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_atomic_state *state);
 void vc4_hvs_atomic_flush(struct drm_crtc *crtc, struct drm_atomic_state *state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_dsi.c
@@ -181,8 +181,50 @@
 
 #define DSI0_TXPKT_PIX_FIFO		0x20 /* AKA PIX_FIFO */
 
-#define DSI0_INT_STAT		0x24
-#define DSI0_INT_EN		0x28
+#define DSI0_INT_STAT			0x24
+#define DSI0_INT_EN			0x28
+# define DSI0_INT_FIFO_ERR		BIT(25)
+# define DSI0_INT_CMDC_DONE_MASK	VC4_MASK(24, 23)
+# define DSI0_INT_CMDC_DONE_SHIFT	23
+#  define DSI0_INT_CMDC_DONE_NO_REPEAT		1
+#  define DSI0_INT_CMDC_DONE_REPEAT		3
+# define DSI0_INT_PHY_DIR_RTF		BIT(22)
+# define DSI0_INT_PHY_D1_ULPS		BIT(21)
+# define DSI0_INT_PHY_D1_STOP		BIT(20)
+# define DSI0_INT_PHY_RXLPDT		BIT(19)
+# define DSI0_INT_PHY_RXTRIG		BIT(18)
+# define DSI0_INT_PHY_D0_ULPS		BIT(17)
+# define DSI0_INT_PHY_D0_LPDT		BIT(16)
+# define DSI0_INT_PHY_D0_FTR		BIT(15)
+# define DSI0_INT_PHY_D0_STOP		BIT(14)
+/* Signaled when the clock lane enters the given state. */
+# define DSI0_INT_PHY_CLK_ULPS		BIT(13)
+# define DSI0_INT_PHY_CLK_HS		BIT(12)
+# define DSI0_INT_PHY_CLK_FTR		BIT(11)
+/* Signaled on timeouts */
+# define DSI0_INT_PR_TO			BIT(10)
+# define DSI0_INT_TA_TO			BIT(9)
+# define DSI0_INT_LPRX_TO		BIT(8)
+# define DSI0_INT_HSTX_TO		BIT(7)
+/* Contention on a line when trying to drive the line low */
+# define DSI0_INT_ERR_CONT_LP1		BIT(6)
+# define DSI0_INT_ERR_CONT_LP0		BIT(5)
+/* Control error: incorrect line state sequence on data lane 0. */
+# define DSI0_INT_ERR_CONTROL		BIT(4)
+# define DSI0_INT_ERR_SYNC_ESC		BIT(3)
+# define DSI0_INT_RX2_PKT		BIT(2)
+# define DSI0_INT_RX1_PKT		BIT(1)
+# define DSI0_INT_CMD_PKT		BIT(0)
+
+#define DSI0_INTERRUPTS_ALWAYS_ENABLED	(DSI0_INT_ERR_SYNC_ESC | \
+					 DSI0_INT_ERR_CONTROL |	 \
+					 DSI0_INT_ERR_CONT_LP0 | \
+					 DSI0_INT_ERR_CONT_LP1 | \
+					 DSI0_INT_HSTX_TO |	 \
+					 DSI0_INT_LPRX_TO |	 \
+					 DSI0_INT_TA_TO |	 \
+					 DSI0_INT_PR_TO)
+
 # define DSI1_INT_PHY_D3_ULPS		BIT(30)
 # define DSI1_INT_PHY_D3_STOP		BIT(29)
 # define DSI1_INT_PHY_D2_ULPS		BIT(28)
@@ -761,6 +803,9 @@
 	list_for_each_entry_reverse(iter, &dsi->bridge_chain, chain_node) {
 		if (iter->funcs->disable)
 			iter->funcs->disable(iter);
+
+		if (iter == dsi->bridge)
+			break;
 	}
 
 	vc4_dsi_ulps(dsi, true);
@@ -805,11 +850,9 @@
 	/* Find what divider gets us a faster clock than the requested
 	 * pixel clock.
 	 */
-	for (divider = 1; divider < 8; divider++) {
-		if (parent_rate / divider < pll_clock) {
-			divider--;
+	for (divider = 1; divider < 255; divider++) {
+		if (parent_rate / (divider + 1) < pll_clock)
 			break;
-		}
 	}
 
 	/* Now that we've picked a PLL divider, calculate back to its
@@ -846,7 +889,7 @@
 	unsigned long phy_clock;
 	int ret;
 
-	ret = pm_runtime_get_sync(dev);
+	ret = pm_runtime_resume_and_get(dev);
 	if (ret) {
 		DRM_ERROR("Failed to runtime PM enable on DSI%d\n", dsi->variant->port);
 		return;
@@ -894,6 +937,9 @@
 
 		DSI_PORT_WRITE(PHY_AFEC0, afec0);
 
+		/* AFEC reset hold time */
+		mdelay(1);
+
 		DSI_PORT_WRITE(PHY_AFEC1,
 			       VC4_SET_FIELD(6,  DSI0_PHY_AFEC1_IDR_DLANE1) |
 			       VC4_SET_FIELD(6,  DSI0_PHY_AFEC1_IDR_DLANE0) |
@@ -1060,12 +1106,9 @@
 		DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI1_CTRL_EN);
 
 	/* Bring AFE out of reset. */
-	if (dsi->variant->port == 0) {
-	} else {
-		DSI_PORT_WRITE(PHY_AFEC0,
-			       DSI_PORT_READ(PHY_AFEC0) &
-			       ~DSI1_PHY_AFEC0_RESET);
-	}
+	DSI_PORT_WRITE(PHY_AFEC0,
+		       DSI_PORT_READ(PHY_AFEC0) &
+		       ~DSI_PORT_BIT(PHY_AFEC0_RESET));
 
 	vc4_dsi_ulps(dsi, false);
 
@@ -1184,13 +1227,28 @@
 	/* Enable the appropriate interrupt for the transfer completion. */
 	dsi->xfer_result = 0;
 	reinit_completion(&dsi->xfer_completion);
-	DSI_PORT_WRITE(INT_STAT, DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF);
-	if (msg->rx_len) {
-		DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
-					DSI1_INT_PHY_DIR_RTF));
+	if (dsi->variant->port == 0) {
+		DSI_PORT_WRITE(INT_STAT,
+			       DSI0_INT_CMDC_DONE_MASK | DSI1_INT_PHY_DIR_RTF);
+		if (msg->rx_len) {
+			DSI_PORT_WRITE(INT_EN, (DSI0_INTERRUPTS_ALWAYS_ENABLED |
+						DSI0_INT_PHY_DIR_RTF));
+		} else {
+			DSI_PORT_WRITE(INT_EN,
+				       (DSI0_INTERRUPTS_ALWAYS_ENABLED |
+					VC4_SET_FIELD(DSI0_INT_CMDC_DONE_NO_REPEAT,
+						      DSI0_INT_CMDC_DONE)));
+		}
 	} else {
-		DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
-					DSI1_INT_TXPKT1_DONE));
+		DSI_PORT_WRITE(INT_STAT,
+			       DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF);
+		if (msg->rx_len) {
+			DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
+						DSI1_INT_PHY_DIR_RTF));
+		} else {
+			DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
+						DSI1_INT_TXPKT1_DONE));
+		}
 	}
 
 	/* Send the packet. */
@@ -1207,7 +1265,7 @@
 		ret = dsi->xfer_result;
 	}
 
-	DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
+	DSI_PORT_WRITE(INT_EN, DSI_PORT_BIT(INTERRUPTS_ALWAYS_ENABLED));
 
 	if (ret)
 		goto reset_fifo_and_return;
@@ -1253,7 +1311,7 @@
 		       DSI_PORT_BIT(CTRL_RESET_FIFOS));
 
 	DSI_PORT_WRITE(TXPKT1C, 0);
-	DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
+	DSI_PORT_WRITE(INT_EN, DSI_PORT_BIT(INTERRUPTS_ALWAYS_ENABLED));
 	return ret;
 }
 
@@ -1262,7 +1320,6 @@
 			       struct mipi_dsi_device *device)
 {
 	struct vc4_dsi *dsi = host_to_dsi(host);
-	int ret;
 
 	dsi->lanes = device->lanes;
 	dsi->channel = device->channel;
@@ -1297,18 +1354,15 @@
 		return 0;
 	}
 
-	ret = component_add(&dsi->pdev->dev, &vc4_dsi_ops);
-	if (ret) {
-		mipi_dsi_host_unregister(&dsi->dsi_host);
-		return ret;
-	}
-
-	return 0;
+	return component_add(&dsi->pdev->dev, &vc4_dsi_ops);
 }
 
 static int vc4_dsi_host_detach(struct mipi_dsi_host *host,
 			       struct mipi_dsi_device *device)
 {
+	struct vc4_dsi *dsi = host_to_dsi(host);
+
+	component_del(&dsi->pdev->dev, &vc4_dsi_ops);
 	return 0;
 }
 
@@ -1394,26 +1448,28 @@
 	DSI_PORT_WRITE(INT_STAT, stat);
 
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_ERR_SYNC_ESC, "LPDT sync");
+			 DSI_PORT_BIT(INT_ERR_SYNC_ESC), "LPDT sync");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_ERR_CONTROL, "data lane 0 sequence");
+			 DSI_PORT_BIT(INT_ERR_CONTROL), "data lane 0 sequence");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_ERR_CONT_LP0, "LP0 contention");
+			 DSI_PORT_BIT(INT_ERR_CONT_LP0), "LP0 contention");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_ERR_CONT_LP1, "LP1 contention");
+			 DSI_PORT_BIT(INT_ERR_CONT_LP1), "LP1 contention");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_HSTX_TO, "HSTX timeout");
+			 DSI_PORT_BIT(INT_HSTX_TO), "HSTX timeout");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_LPRX_TO, "LPRX timeout");
+			 DSI_PORT_BIT(INT_LPRX_TO), "LPRX timeout");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_TA_TO, "turnaround timeout");
+			 DSI_PORT_BIT(INT_TA_TO), "turnaround timeout");
 	dsi_handle_error(dsi, &ret, stat,
-			 DSI1_INT_PR_TO, "peripheral reset timeout");
+			 DSI_PORT_BIT(INT_PR_TO), "peripheral reset timeout");
 
-	if (stat & (DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF)) {
+	if (stat & ((dsi->variant->port ? DSI1_INT_TXPKT1_DONE :
+					  DSI0_INT_CMDC_DONE_MASK) |
+		    DSI_PORT_BIT(INT_PHY_DIR_RTF))) {
 		complete(&dsi->xfer_completion);
 		ret = IRQ_HANDLED;
-	} else if (stat & DSI1_INT_HSTX_TO) {
+	} else if (stat & DSI_PORT_BIT(INT_HSTX_TO)) {
 		complete(&dsi->xfer_completion);
 		dsi->xfer_result = -ETIMEDOUT;
 		ret = IRQ_HANDLED;
@@ -1491,22 +1547,32 @@
 				      dsi->clk_onecell);
 }
 
+static void vc4_dsi_dma_mem_release(void *ptr)
+{
+	struct vc4_dsi *dsi = ptr;
+	struct device *dev = &dsi->pdev->dev;
+
+	dma_free_coherent(dev, 4, dsi->reg_dma_mem, dsi->reg_dma_paddr);
+	dsi->reg_dma_mem = NULL;
+}
+
+static void vc4_dsi_dma_chan_release(void *ptr)
+{
+	struct vc4_dsi *dsi = ptr;
+
+	dma_release_channel(dsi->reg_dma_chan);
+	dsi->reg_dma_chan = NULL;
+}
+
 static int vc4_dsi_bind(struct device *dev, struct device *master, void *data)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct drm_device *drm = dev_get_drvdata(master);
 	struct vc4_dsi *dsi = dev_get_drvdata(dev);
 	struct vc4_dsi_encoder *vc4_dsi_encoder;
-	struct drm_panel *panel;
-	const struct of_device_id *match;
-	dma_cap_mask_t dma_mask;
 	int ret;
 
-	match = of_match_device(vc4_dsi_dt_match, dev);
-	if (!match)
-		return -ENODEV;
-
-	dsi->variant = match->data;
+	dsi->variant = of_device_get_match_data(dev);
 
 	vc4_dsi_encoder = devm_kzalloc(dev, sizeof(*vc4_dsi_encoder),
 				       GFP_KERNEL);
@@ -1514,7 +1580,8 @@
 		return -ENOMEM;
 
 	INIT_LIST_HEAD(&dsi->bridge_chain);
-	vc4_dsi_encoder->base.type = VC4_ENCODER_TYPE_DSI1;
+	vc4_dsi_encoder->base.type = dsi->variant->port ?
+			VC4_ENCODER_TYPE_DSI1 : VC4_ENCODER_TYPE_DSI0;
 	vc4_dsi_encoder->dsi = dsi;
 	dsi->encoder = &vc4_dsi_encoder->base.base;
 
@@ -1537,6 +1604,8 @@
 	 * so set up a channel for talking to it.
 	 */
 	if (dsi->variant->broken_axi_workaround) {
+		dma_cap_mask_t dma_mask;
+
 		dsi->reg_dma_mem = dma_alloc_coherent(dev, 4,
 						      &dsi->reg_dma_paddr,
 						      GFP_KERNEL);
@@ -1545,8 +1614,13 @@
 			return -ENOMEM;
 		}
 
+		ret = devm_add_action_or_reset(dev, vc4_dsi_dma_mem_release, dsi);
+		if (ret)
+			return ret;
+
 		dma_cap_zero(dma_mask);
 		dma_cap_set(DMA_MEMCPY, dma_mask);
+
 		dsi->reg_dma_chan = dma_request_chan_by_mask(&dma_mask);
 		if (IS_ERR(dsi->reg_dma_chan)) {
 			ret = PTR_ERR(dsi->reg_dma_chan);
@@ -1556,6 +1630,10 @@
 			return ret;
 		}
 
+		ret = devm_add_action_or_reset(dev, vc4_dsi_dma_chan_release, dsi);
+		if (ret)
+			return ret;
+
 		/* Get the physical address of the device's registers.  The
 		 * struct resource for the regs gives us the bus address
 		 * instead.
@@ -1609,27 +1687,9 @@
 		return ret;
 	}
 
-	ret = drm_of_find_panel_or_bridge(dev->of_node, 0, 0,
-					  &panel, &dsi->bridge);
-	if (ret) {
-		/* If the bridge or panel pointed by dev->of_node is not
-		 * enabled, just return 0 here so that we don't prevent the DRM
-		 * dev from being registered. Of course that means the DSI
-		 * encoder won't be exposed, but that's not a problem since
-		 * nothing is connected to it.
-		 */
-		if (ret == -ENODEV)
-			return 0;
-
-		return ret;
-	}
-
-	if (panel) {
-		dsi->bridge = devm_drm_panel_bridge_add_typed(dev, panel,
-							      DRM_MODE_CONNECTOR_DSI);
-		if (IS_ERR(dsi->bridge))
-			return PTR_ERR(dsi->bridge);
-	}
+	dsi->bridge = devm_drm_of_get_bridge(dev, dev->of_node, 0, 0);
+	if (IS_ERR(dsi->bridge))
+		return PTR_ERR(dsi->bridge);
 
 	/* The esc clock rate is supposed to always be 100Mhz. */
 	ret = clk_set_rate(dsi->escape_clock, 100 * 1000000);
@@ -1667,8 +1727,7 @@
 {
 	struct vc4_dsi *dsi = dev_get_drvdata(dev);
 
-	if (dsi->bridge)
-		pm_runtime_disable(dev);
+	pm_runtime_disable(dev);
 
 	/*
 	 * Restore the bridge_chain so the bridge detach procedure can happen
@@ -1706,9 +1765,7 @@
 	struct device *dev = &pdev->dev;
 	struct vc4_dsi *dsi = dev_get_drvdata(dev);
 
-	component_del(&pdev->dev, &vc4_dsi_ops);
 	mipi_dsi_host_unregister(&dsi->dsi_host);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -38,6 +38,7 @@
 #include <drm/drm_scdc_helper.h>
 #include <linux/clk.h>
 #include <linux/component.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/of_address.h>
 #include <linux/of_gpio.h>
@@ -78,6 +79,9 @@
 #define VC5_HDMI_VERTB_VSPO_SHIFT		16
 #define VC5_HDMI_VERTB_VSPO_MASK		VC4_MASK(29, 16)
 
+#define VC5_HDMI_MISC_CONTROL_PIXEL_REP_SHIFT	0
+#define VC5_HDMI_MISC_CONTROL_PIXEL_REP_MASK	VC4_MASK(3, 0)
+
 #define VC5_HDMI_SCRAMBLER_CTL_ENABLE		BIT(0)
 
 #define VC5_HDMI_DEEP_COLOR_CONFIG_1_INIT_PACK_PHASE_SHIFT	8
@@ -94,6 +98,7 @@
 # define VC4_HD_M_SW_RST			BIT(2)
 # define VC4_HD_M_ENABLE			BIT(0)
 
+#define HSM_MIN_CLOCK_FREQ	120000000
 #define CEC_CLOCK_FREQ 40000
 
 #define HDMI_14_MAX_TMDS_CLK   (340 * 1000 * 1000)
@@ -161,15 +166,19 @@
 static void vc4_hdmi_cec_update_clk_div(struct vc4_hdmi *vc4_hdmi) {}
 #endif
 
+static void vc4_hdmi_enable_scrambling(struct drm_encoder *encoder);
+
 static enum drm_connector_status
 vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
 	struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
 	bool connected = false;
 
-	if (vc4_hdmi->hpd_gpio &&
-	    gpiod_get_value_cansleep(vc4_hdmi->hpd_gpio)) {
-		connected = true;
+	WARN_ON(pm_runtime_resume_and_get(&vc4_hdmi->pdev->dev));
+
+	if (vc4_hdmi->hpd_gpio) {
+		if (gpiod_get_value_cansleep(vc4_hdmi->hpd_gpio))
+			connected = true;
 	} else if (drm_probe_ddc(vc4_hdmi->ddc)) {
 		connected = true;
 	} else if (HDMI_READ(HDMI_HOTPLUG) & VC4_HDMI_HOTPLUG_CONNECTED) {
@@ -187,10 +196,13 @@
 			}
 		}
 
+		vc4_hdmi_enable_scrambling(&vc4_hdmi->encoder.base.base);
+		pm_runtime_put(&vc4_hdmi->pdev->dev);
 		return connector_status_connected;
 	}
 
 	cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
+	pm_runtime_put(&vc4_hdmi->pdev->dev);
 	return connector_status_disconnected;
 }
 
@@ -210,7 +222,7 @@
 	edid = drm_get_edid(connector, vc4_hdmi->ddc);
 	cec_s_phys_addr_from_edid(vc4_hdmi->cec_adap, edid);
 	if (!edid)
-		return -ENODEV;
+		return 0;
 
 	vc4_encoder->hdmi_monitor = drm_detect_hdmi_monitor(edid);
 
@@ -627,7 +639,6 @@
 		vc4_hdmi->variant->phy_disable(vc4_hdmi);
 
 	clk_disable_unprepare(vc4_hdmi->pixel_bvb_clock);
-	clk_disable_unprepare(vc4_hdmi->hsm_clock);
 	clk_disable_unprepare(vc4_hdmi->pixel_clock);
 
 	ret = pm_runtime_put(&vc4_hdmi->pdev->dev);
@@ -727,12 +738,12 @@
 				   VC4_HDMI_VERTA_VFP) |
 		     VC4_SET_FIELD(mode->crtc_vdisplay, VC4_HDMI_VERTA_VAL));
 	u32 vertb = (VC4_SET_FIELD(0, VC4_HDMI_VERTB_VSPO) |
-		     VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
+		     VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end +
+				   interlaced,
 				   VC4_HDMI_VERTB_VBP));
 	u32 vertb_even = (VC4_SET_FIELD(0, VC4_HDMI_VERTB_VSPO) |
 			  VC4_SET_FIELD(mode->crtc_vtotal -
-					mode->crtc_vsync_end -
-					interlaced,
+					mode->crtc_vsync_end,
 					VC4_HDMI_VERTB_VBP));
 
 	HDMI_WRITE(HDMI_HORZA,
@@ -772,13 +783,14 @@
 		     VC4_SET_FIELD(mode->crtc_vsync_start - mode->crtc_vdisplay,
 				   VC5_HDMI_VERTA_VFP) |
 		     VC4_SET_FIELD(mode->crtc_vdisplay, VC5_HDMI_VERTA_VAL));
-	u32 vertb = (VC4_SET_FIELD(0, VC5_HDMI_VERTB_VSPO) |
-		     VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
+	u32 vertb = (VC4_SET_FIELD(mode->htotal >> (2 - pixel_rep),
+				   VC5_HDMI_VERTB_VSPO) |
+		     VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end +
+				   interlaced,
 				   VC4_HDMI_VERTB_VBP));
 	u32 vertb_even = (VC4_SET_FIELD(0, VC5_HDMI_VERTB_VSPO) |
 			  VC4_SET_FIELD(mode->crtc_vtotal -
-					mode->crtc_vsync_end -
-					interlaced,
+					mode->crtc_vsync_end,
 					VC4_HDMI_VERTB_VBP));
 	unsigned char gcp;
 	bool gcp_en;
@@ -841,6 +853,11 @@
 	reg |= gcp_en ? VC5_HDMI_GCP_CONFIG_GCP_ENABLE : 0;
 	HDMI_WRITE(HDMI_GCP_CONFIG, reg);
 
+	reg = HDMI_READ(HDMI_MISC_CONTROL);
+	reg &= ~VC5_HDMI_MISC_CONTROL_PIXEL_REP_MASK;
+	reg |= VC4_SET_FIELD(0, VC5_HDMI_MISC_CONTROL_PIXEL_REP);
+	HDMI_WRITE(HDMI_MISC_CONTROL, reg);
+
 	HDMI_WRITE(HDMI_CLOCK_STOP, 0);
 }
 
@@ -893,28 +910,10 @@
 		conn_state_to_vc4_hdmi_conn_state(conn_state);
 	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
 	struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
-	unsigned long bvb_rate, pixel_rate, hsm_rate;
+	unsigned long pixel_rate = vc4_conn_state->pixel_rate;
+	unsigned long bvb_rate, hsm_rate;
 	int ret;
 
-	ret = pm_runtime_resume_and_get(&vc4_hdmi->pdev->dev);
-	if (ret < 0) {
-		DRM_ERROR("Failed to retain power domain: %d\n", ret);
-		return;
-	}
-
-	pixel_rate = vc4_conn_state->pixel_rate;
-	ret = clk_set_rate(vc4_hdmi->pixel_clock, pixel_rate);
-	if (ret) {
-		DRM_ERROR("Failed to set pixel clock rate: %d\n", ret);
-		return;
-	}
-
-	ret = clk_prepare_enable(vc4_hdmi->pixel_clock);
-	if (ret) {
-		DRM_ERROR("Failed to turn on pixel clock: %d\n", ret);
-		return;
-	}
-
 	/*
 	 * As stated in RPi's vc4 firmware "HDMI state machine (HSM) clock must
 	 * be faster than pixel clock, infinitesimally faster, tested in
@@ -938,13 +937,25 @@
 		return;
 	}
 
-	ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
-	if (ret) {
-		DRM_ERROR("Failed to turn on HSM clock: %d\n", ret);
-		clk_disable_unprepare(vc4_hdmi->pixel_clock);
+	ret = pm_runtime_resume_and_get(&vc4_hdmi->pdev->dev);
+	if (ret < 0) {
+		DRM_ERROR("Failed to retain power domain: %d\n", ret);
 		return;
 	}
 
+	ret = clk_set_rate(vc4_hdmi->pixel_clock, pixel_rate);
+	if (ret) {
+		DRM_ERROR("Failed to set pixel clock rate: %d\n", ret);
+		goto err_put_runtime_pm;
+	}
+
+	ret = clk_prepare_enable(vc4_hdmi->pixel_clock);
+	if (ret) {
+		DRM_ERROR("Failed to turn on pixel clock: %d\n", ret);
+		goto err_put_runtime_pm;
+	}
+
+
 	vc4_hdmi_cec_update_clk_div(vc4_hdmi);
 
 	if (pixel_rate > 297000000)
@@ -957,17 +968,13 @@
 	ret = clk_set_min_rate(vc4_hdmi->pixel_bvb_clock, bvb_rate);
 	if (ret) {
 		DRM_ERROR("Failed to set pixel bvb clock rate: %d\n", ret);
-		clk_disable_unprepare(vc4_hdmi->hsm_clock);
-		clk_disable_unprepare(vc4_hdmi->pixel_clock);
-		return;
+		goto err_disable_pixel_clock;
 	}
 
 	ret = clk_prepare_enable(vc4_hdmi->pixel_bvb_clock);
 	if (ret) {
 		DRM_ERROR("Failed to turn on pixel bvb clock: %d\n", ret);
-		clk_disable_unprepare(vc4_hdmi->hsm_clock);
-		clk_disable_unprepare(vc4_hdmi->pixel_clock);
-		return;
+		goto err_disable_pixel_clock;
 	}
 
 	if (vc4_hdmi->variant->phy_init)
@@ -980,6 +987,15 @@
 
 	if (vc4_hdmi->variant->set_timings)
 		vc4_hdmi->variant->set_timings(vc4_hdmi, conn_state, mode);
+
+	return;
+
+err_disable_pixel_clock:
+	clk_disable_unprepare(vc4_hdmi->pixel_clock);
+err_put_runtime_pm:
+	pm_runtime_put(&vc4_hdmi->pdev->dev);
+
+	return;
 }
 
 static void vc4_hdmi_encoder_pre_crtc_enable(struct drm_encoder *encoder,
@@ -1084,6 +1100,7 @@
 	unsigned long long tmds_rate;
 
 	if (vc4_hdmi->variant->unsupported_odd_h_timings &&
+	    !(mode->flags & DRM_MODE_FLAG_DBLCLK) &&
 	    ((mode->hdisplay % 2) || (mode->hsync_start % 2) ||
 	     (mode->hsync_end % 2) || (mode->htotal % 2)))
 		return -EINVAL;
@@ -1131,6 +1148,7 @@
 	struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
 
 	if (vc4_hdmi->variant->unsupported_odd_h_timings &&
+	    !(mode->flags & DRM_MODE_FLAG_DBLCLK) &&
 	    ((mode->hdisplay % 2) || (mode->hsync_start % 2) ||
 	     (mode->hsync_end % 2) || (mode->htotal % 2)))
 		return MODE_H_ILLEGAL;
@@ -1374,10 +1392,10 @@
 
 	/* Set the MAI threshold */
 	HDMI_WRITE(HDMI_MAI_THR,
-		   VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_PANICHIGH) |
-		   VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_PANICLOW) |
-		   VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_DREQHIGH) |
-		   VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_DREQLOW));
+		   VC4_SET_FIELD(0x08, VC4_HD_MAI_THR_PANICHIGH) |
+		   VC4_SET_FIELD(0x08, VC4_HD_MAI_THR_PANICLOW) |
+		   VC4_SET_FIELD(0x06, VC4_HD_MAI_THR_DREQHIGH) |
+		   VC4_SET_FIELD(0x08, VC4_HD_MAI_THR_DREQLOW));
 
 	HDMI_WRITE(HDMI_MAI_CONFIG,
 		   VC4_HDMI_MAI_CONFIG_BIT_REVERSE |
@@ -1461,12 +1479,12 @@
 	struct device *dev = &vc4_hdmi->pdev->dev;
 	struct platform_device *codec_pdev;
 	const __be32 *addr;
-	int index;
+	int index, len;
 	int ret;
 
-	if (!of_find_property(dev->of_node, "dmas", NULL)) {
+	if (!of_find_property(dev->of_node, "dmas", &len) || !len) {
 		dev_warn(dev,
-			 "'dmas' DT property is missing, no HDMI audio\n");
+			 "'dmas' DT property is missing or empty, no HDMI audio\n");
 		return 0;
 	}
 
@@ -1488,6 +1506,8 @@
 		index = 1;
 
 	addr = of_get_address(dev->of_node, index, NULL, NULL);
+	if (!addr)
+		return -EINVAL;
 
 	vc4_hdmi->audio.dma_data.addr = be32_to_cpup(addr) + mai_data->offset;
 	vc4_hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
@@ -1514,6 +1534,7 @@
 		dev_err(dev, "Couldn't register the HDMI codec: %ld\n", PTR_ERR(codec_pdev));
 		return PTR_ERR(codec_pdev);
 	}
+	vc4_hdmi->audio.codec_pdev = codec_pdev;
 
 	dai_link->cpus		= &vc4_hdmi->audio.cpu;
 	dai_link->codecs	= &vc4_hdmi->audio.codec;
@@ -1553,6 +1574,12 @@
 
 }
 
+static void vc4_hdmi_audio_exit(struct vc4_hdmi *vc4_hdmi)
+{
+	platform_device_unregister(vc4_hdmi->audio.codec_pdev);
+	vc4_hdmi->audio.codec_pdev = NULL;
+}
+
 static irqreturn_t vc4_hdmi_hpd_irq_thread(int irq, void *priv)
 {
 	struct vc4_hdmi *vc4_hdmi = priv;
@@ -1830,7 +1857,8 @@
 	}
 
 	vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
-						  vc4_hdmi, "vc4",
+						  vc4_hdmi,
+						  vc4_hdmi->variant->card_name,
 						  CEC_CAP_DEFAULTS |
 						  CEC_CAP_CONNECTOR_INFO, 1);
 	ret = PTR_ERR_OR_ZERO(vc4_hdmi->cec_adap);
@@ -2098,6 +2126,27 @@
 	return 0;
 }
 
+static int vc4_hdmi_runtime_suspend(struct device *dev)
+{
+	struct vc4_hdmi *vc4_hdmi = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(vc4_hdmi->hsm_clock);
+
+	return 0;
+}
+
+static int vc4_hdmi_runtime_resume(struct device *dev)
+{
+	struct vc4_hdmi *vc4_hdmi = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
 static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
 {
 	const struct vc4_hdmi_variant *variant = of_device_get_match_data(dev);
@@ -2161,6 +2210,29 @@
 			vc4_hdmi->disable_4kp60 = true;
 	}
 
+	/*
+	 * If we boot without any cable connected to the HDMI connector,
+	 * the firmware will skip the HSM initialization and leave it
+	 * with a rate of 0, resulting in a bus lockup when we're
+	 * accessing the registers even if it's enabled.
+	 *
+	 * Let's put a sensible default at runtime_resume so that we
+	 * don't end up in this situation.
+	 */
+	ret = clk_set_min_rate(vc4_hdmi->hsm_clock, HSM_MIN_CLOCK_FREQ);
+	if (ret)
+		goto err_put_ddc;
+
+	pm_runtime_enable(dev);
+
+	/*
+	 *  We need to have the device powered up at this point to call
+	 *  our reset hook and for the CEC init.
+	 */
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret)
+		goto err_disable_runtime_pm;
+
 	if (vc4_hdmi->variant->reset)
 		vc4_hdmi->variant->reset(vc4_hdmi);
 
@@ -2172,8 +2244,6 @@
 		clk_prepare_enable(vc4_hdmi->pixel_bvb_clock);
 	}
 
-	pm_runtime_enable(dev);
-
 	drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
 	drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
 
@@ -2197,6 +2267,8 @@
 			     vc4_hdmi_debugfs_regs,
 			     vc4_hdmi);
 
+	pm_runtime_put_sync(dev);
+
 	return 0;
 
 err_free_cec:
@@ -2207,6 +2279,8 @@
 	vc4_hdmi_connector_destroy(&vc4_hdmi->connector);
 err_destroy_encoder:
 	drm_encoder_cleanup(encoder);
+	pm_runtime_put_sync(dev);
+err_disable_runtime_pm:
 	pm_runtime_disable(dev);
 err_put_ddc:
 	put_device(&vc4_hdmi->ddc->dev);
@@ -2243,6 +2317,7 @@
 	kfree(vc4_hdmi->hdmi_regset.regs);
 	kfree(vc4_hdmi->hd_regset.regs);
 
+	vc4_hdmi_audio_exit(vc4_hdmi);
 	vc4_hdmi_cec_exit(vc4_hdmi);
 	vc4_hdmi_hotplug_exit(vc4_hdmi);
 	vc4_hdmi_connector_destroy(&vc4_hdmi->connector);
@@ -2352,11 +2427,18 @@
 	{}
 };
 
+static const struct dev_pm_ops vc4_hdmi_pm_ops = {
+	SET_RUNTIME_PM_OPS(vc4_hdmi_runtime_suspend,
+			   vc4_hdmi_runtime_resume,
+			   NULL)
+};
+
 struct platform_driver vc4_hdmi_driver = {
 	.probe = vc4_hdmi_dev_probe,
 	.remove = vc4_hdmi_dev_remove,
 	.driver = {
 		.name = "vc4_hdmi",
 		.of_match_table = vc4_hdmi_dt_match,
+		.pm = &vc4_hdmi_pm_ops,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -113,6 +113,7 @@
 	struct snd_soc_dai_link_component platform;
 	struct snd_dmaengine_dai_dma_data dma_data;
 	struct hdmi_audio_infoframe infoframe;
+	struct platform_device *codec_pdev;
 	bool streaming;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_hdmi_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_hdmi_regs.h
@@ -123,6 +123,7 @@
 	HDMI_VERTB0,
 	HDMI_VERTB1,
 	HDMI_VID_CTL,
+	HDMI_MISC_CONTROL,
 };
 
 struct vc4_hdmi_register {
@@ -233,6 +234,7 @@
 	VC4_HDMI_REG(HDMI_VERTB0, 0x0f0),
 	VC4_HDMI_REG(HDMI_VERTA1, 0x0f4),
 	VC4_HDMI_REG(HDMI_VERTB1, 0x0f8),
+	VC4_HDMI_REG(HDMI_MISC_CONTROL, 0x100),
 	VC4_HDMI_REG(HDMI_MAI_CHANNEL_MAP, 0x09c),
 	VC4_HDMI_REG(HDMI_MAI_CONFIG, 0x0a0),
 	VC4_HDMI_REG(HDMI_DEEP_COLOR_CONFIG_1, 0x170),
@@ -313,6 +315,7 @@
 	VC4_HDMI_REG(HDMI_VERTB0, 0x0f0),
 	VC4_HDMI_REG(HDMI_VERTA1, 0x0f4),
 	VC4_HDMI_REG(HDMI_VERTB1, 0x0f8),
+	VC4_HDMI_REG(HDMI_MISC_CONTROL, 0x100),
 	VC4_HDMI_REG(HDMI_MAI_CHANNEL_MAP, 0x09c),
 	VC4_HDMI_REG(HDMI_MAI_CONFIG, 0x0a0),
 	VC4_HDMI_REG(HDMI_DEEP_COLOR_CONFIG_1, 0x170),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_hvs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -197,6 +197,29 @@
 	vc4_hvs_lut_load(crtc);
 }
 
+u8 vc4_hvs_get_fifo_frame_count(struct drm_device *dev, unsigned int fifo)
+{
+	struct vc4_dev *vc4 = to_vc4_dev(dev);
+	u8 field = 0;
+
+	switch (fifo) {
+	case 0:
+		field = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTAT1),
+				      SCALER_DISPSTAT1_FRCNT0);
+		break;
+	case 1:
+		field = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTAT1),
+				      SCALER_DISPSTAT1_FRCNT1);
+		break;
+	case 2:
+		field = VC4_GET_FIELD(HVS_READ(SCALER_DISPSTAT2),
+				      SCALER_DISPSTAT2_FRCNT2);
+		break;
+	}
+
+	return field;
+}
+
 int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output)
 {
 	struct vc4_dev *vc4 = to_vc4_dev(dev);
@@ -365,17 +388,16 @@
 	struct vc4_dev *vc4 = to_vc4_dev(dev);
 	struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
 	struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
+	unsigned long flags;
 
 	if (crtc->state->event) {
-		unsigned long flags;
-
 		crtc->state->event->pipe = drm_crtc_index(crtc);
 
 		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
 
 		spin_lock_irqsave(&dev->event_lock, flags);
 
-		if (!vc4_state->feed_txp || vc4_state->txp_armed) {
+		if (!vc4_crtc->feeds_txp || vc4_state->txp_armed) {
 			vc4_crtc->event = crtc->state->event;
 			crtc->state->event = NULL;
 		}
@@ -388,6 +410,22 @@
 		HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
 			  vc4_state->mm.start);
 	}
+
+	spin_lock_irqsave(&vc4_crtc->irq_lock, flags);
+	vc4_crtc->current_dlist = vc4_state->mm.start;
+	spin_unlock_irqrestore(&vc4_crtc->irq_lock, flags);
+}
+
+void vc4_hvs_atomic_begin(struct drm_crtc *crtc,
+			  struct drm_atomic_state *state)
+{
+	struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+	struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
+	unsigned long flags;
+
+	spin_lock_irqsave(&vc4_crtc->irq_lock, flags);
+	vc4_crtc->current_hvs_channel = vc4_state->assigned_channel;
+	spin_unlock_irqrestore(&vc4_crtc->irq_lock, flags);
 }
 
 void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
@@ -395,10 +433,9 @@
 {
 	struct drm_device *dev = crtc->dev;
 	struct vc4_dev *vc4 = to_vc4_dev(dev);
-	struct drm_crtc_state *new_crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
-	struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(new_crtc_state);
 	struct drm_display_mode *mode = &crtc->state->adjusted_mode;
-	bool oneshot = vc4_state->feed_txp;
+	struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+	bool oneshot = vc4_crtc->feeds_txp;
 
 	vc4_hvs_update_dlist(crtc);
 	vc4_hvs_init_channel(vc4, crtc, mode, oneshot);
@@ -568,6 +605,7 @@
 	struct vc4_hvs *hvs = NULL;
 	int ret;
 	u32 dispctrl;
+	u32 reg;
 
 	hvs = devm_kzalloc(&pdev->dev, sizeof(*hvs), GFP_KERNEL);
 	if (!hvs)
@@ -639,6 +677,26 @@
 
 	vc4->hvs = hvs;
 
+	reg = HVS_READ(SCALER_DISPECTRL);
+	reg &= ~SCALER_DISPECTRL_DSP2_MUX_MASK;
+	HVS_WRITE(SCALER_DISPECTRL,
+		  reg | VC4_SET_FIELD(0, SCALER_DISPECTRL_DSP2_MUX));
+
+	reg = HVS_READ(SCALER_DISPCTRL);
+	reg &= ~SCALER_DISPCTRL_DSP3_MUX_MASK;
+	HVS_WRITE(SCALER_DISPCTRL,
+		  reg | VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX));
+
+	reg = HVS_READ(SCALER_DISPEOLN);
+	reg &= ~SCALER_DISPEOLN_DSP4_MUX_MASK;
+	HVS_WRITE(SCALER_DISPEOLN,
+		  reg | VC4_SET_FIELD(3, SCALER_DISPEOLN_DSP4_MUX));
+
+	reg = HVS_READ(SCALER_DISPDITHER);
+	reg &= ~SCALER_DISPDITHER_DSP5_MUX_MASK;
+	HVS_WRITE(SCALER_DISPDITHER,
+		  reg | VC4_SET_FIELD(3, SCALER_DISPDITHER_DSP5_MUX));
+
 	dispctrl = HVS_READ(SCALER_DISPCTRL);
 
 	dispctrl |= SCALER_DISPCTRL_ENABLE;
@@ -646,10 +704,6 @@
 		    SCALER_DISPCTRL_DISPEIRQ(1) |
 		    SCALER_DISPCTRL_DISPEIRQ(2);
 
-	/* Set DSP3 (PV1) to use HVS channel 2, which would otherwise
-	 * be unused.
-	 */
-	dispctrl &= ~SCALER_DISPCTRL_DSP3_MUX_MASK;
 	dispctrl &= ~(SCALER_DISPCTRL_DMAEIRQ |
 		      SCALER_DISPCTRL_SLVWREIRQ |
 		      SCALER_DISPCTRL_SLVRDEIRQ |
@@ -663,7 +717,28 @@
 		      SCALER_DISPCTRL_DSPEISLUR(1) |
 		      SCALER_DISPCTRL_DSPEISLUR(2) |
 		      SCALER_DISPCTRL_SCLEIRQ);
-	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
+
+	/* Set AXI panic mode.
+	 * VC4 panics when < 2 lines in FIFO.
+	 * VC5 panics when less than 1 line in the FIFO.
+	 */
+	dispctrl &= ~(SCALER_DISPCTRL_PANIC0_MASK |
+		      SCALER_DISPCTRL_PANIC1_MASK |
+		      SCALER_DISPCTRL_PANIC2_MASK);
+	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC0);
+	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC1);
+	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC2);
+
+	/* Set AXI panic mode.
+	 * VC4 panics when < 2 lines in FIFO.
+	 * VC5 panics when less than 1 line in the FIFO.
+	 */
+	dispctrl &= ~(SCALER_DISPCTRL_PANIC0_MASK |
+		      SCALER_DISPCTRL_PANIC1_MASK |
+		      SCALER_DISPCTRL_PANIC2_MASK);
+	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC0);
+	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC1);
+	dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_PANIC2);
 
 	HVS_WRITE(SCALER_DISPCTRL, dispctrl);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_kms.c
@@ -193,8 +193,8 @@
 	struct drm_private_state *priv_state;
 
 	priv_state = drm_atomic_get_new_private_obj_state(state, &vc4->hvs_channels);
-	if (IS_ERR(priv_state))
-		return ERR_CAST(priv_state);
+	if (!priv_state)
+		return ERR_PTR(-EINVAL);
 
 	return to_vc4_hvs_state(priv_state);
 }
@@ -206,8 +206,8 @@
 	struct drm_private_state *priv_state;
 
 	priv_state = drm_atomic_get_old_private_obj_state(state, &vc4->hvs_channels);
-	if (IS_ERR(priv_state))
-		return ERR_CAST(priv_state);
+	if (!priv_state)
+		return ERR_PTR(-EINVAL);
 
 	return to_vc4_hvs_state(priv_state);
 }
@@ -233,6 +233,7 @@
 	unsigned int i;
 
 	for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+		struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
 		struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
 		u32 dispctrl;
 		u32 dsp3_mux;
@@ -253,7 +254,7 @@
 		 * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
 		 * route.
 		 */
-		if (vc4_state->feed_txp)
+		if (vc4_crtc->feeds_txp)
 			dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
 		else
 			dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
@@ -337,10 +338,10 @@
 	struct drm_device *dev = state->dev;
 	struct vc4_dev *vc4 = to_vc4_dev(dev);
 	struct vc4_hvs *hvs = vc4->hvs;
-	struct drm_crtc_state *old_crtc_state;
 	struct drm_crtc_state *new_crtc_state;
 	struct drm_crtc *crtc;
 	struct vc4_hvs_state *old_hvs_state;
+	unsigned int channel;
 	int i;
 
 	for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
@@ -353,30 +354,32 @@
 		vc4_hvs_mask_underrun(dev, vc4_crtc_state->assigned_channel);
 	}
 
-	if (vc4->hvs->hvs5)
-		clk_set_min_rate(hvs->core_clk, 500000000);
-
 	old_hvs_state = vc4_hvs_get_old_global_state(state);
-	if (!old_hvs_state)
+	if (IS_ERR(old_hvs_state))
 		return;
 
-	for_each_old_crtc_in_state(state, crtc, old_crtc_state, i) {
-		struct vc4_crtc_state *vc4_crtc_state =
-			to_vc4_crtc_state(old_crtc_state);
-		unsigned int channel = vc4_crtc_state->assigned_channel;
+	for (channel = 0; channel < HVS_NUM_CHANNELS; channel++) {
+		struct drm_crtc_commit *commit;
 		int ret;
 
-		if (channel == VC4_HVS_CHANNEL_DISABLED)
+		if (!old_hvs_state->fifo_state[channel].in_use)
 			continue;
 
-		if (!old_hvs_state->fifo_state[channel].in_use)
+		commit = old_hvs_state->fifo_state[channel].pending_commit;
+		if (!commit)
 			continue;
 
-		ret = drm_crtc_commit_wait(old_hvs_state->fifo_state[channel].pending_commit);
+		ret = drm_crtc_commit_wait(commit);
 		if (ret)
 			drm_err(dev, "Timed out waiting for commit\n");
+
+		drm_crtc_commit_put(commit);
+		old_hvs_state->fifo_state[channel].pending_commit = NULL;
 	}
 
+	if (vc4->hvs->hvs5)
+		clk_set_min_rate(hvs->core_clk, 500000000);
+
 	drm_atomic_helper_commit_modeset_disables(dev, state);
 
 	vc4_ctm_commit(vc4, state);
@@ -410,8 +413,8 @@
 	unsigned int i;
 
 	hvs_state = vc4_hvs_get_new_global_state(state);
-	if (!hvs_state)
-		return -EINVAL;
+	if (WARN_ON(IS_ERR(hvs_state)))
+		return PTR_ERR(hvs_state);
 
 	for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
 		struct vc4_crtc_state *vc4_crtc_state =
@@ -668,12 +671,6 @@
 
 	for (i = 0; i < HVS_NUM_CHANNELS; i++) {
 		state->fifo_state[i].in_use = old_state->fifo_state[i].in_use;
-
-		if (!old_state->fifo_state[i].pending_commit)
-			continue;
-
-		state->fifo_state[i].pending_commit =
-			drm_crtc_commit_get(old_state->fifo_state[i].pending_commit);
 	}
 
 	return &state->base;
@@ -762,8 +759,8 @@
 	unsigned int i;
 
 	hvs_new_state = vc4_hvs_get_global_state(state);
-	if (!hvs_new_state)
-		return -EINVAL;
+	if (IS_ERR(hvs_new_state))
+		return PTR_ERR(hvs_new_state);
 
 	for (i = 0; i < ARRAY_SIZE(hvs_new_state->fifo_state); i++)
 		if (!hvs_new_state->fifo_state[i].in_use)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_plane.c
@@ -72,11 +72,13 @@
 		.drm = DRM_FORMAT_ARGB1555,
 		.hvs = HVS_PIXEL_FORMAT_RGBA5551,
 		.pixel_order = HVS_PIXEL_ORDER_ABGR,
+		.pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
 	},
 	{
 		.drm = DRM_FORMAT_XRGB1555,
 		.hvs = HVS_PIXEL_FORMAT_RGBA5551,
 		.pixel_order = HVS_PIXEL_ORDER_ABGR,
+		.pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
 	},
 	{
 		.drm = DRM_FORMAT_RGB888,
@@ -303,16 +305,16 @@
 					       adjhdisplay,
 					       crtc_state->mode.hdisplay);
 	vc4_pstate->crtc_x += left;
-	if (vc4_pstate->crtc_x > crtc_state->mode.hdisplay - left)
-		vc4_pstate->crtc_x = crtc_state->mode.hdisplay - left;
+	if (vc4_pstate->crtc_x > crtc_state->mode.hdisplay - right)
+		vc4_pstate->crtc_x = crtc_state->mode.hdisplay - right;
 
 	adjvdisplay = crtc_state->mode.vdisplay - (top + bottom);
 	vc4_pstate->crtc_y = DIV_ROUND_CLOSEST(vc4_pstate->crtc_y *
 					       adjvdisplay,
 					       crtc_state->mode.vdisplay);
 	vc4_pstate->crtc_y += top;
-	if (vc4_pstate->crtc_y > crtc_state->mode.vdisplay - top)
-		vc4_pstate->crtc_y = crtc_state->mode.vdisplay - top;
+	if (vc4_pstate->crtc_y > crtc_state->mode.vdisplay - bottom)
+		vc4_pstate->crtc_y = crtc_state->mode.vdisplay - bottom;
 
 	vc4_pstate->crtc_w = DIV_ROUND_CLOSEST(vc4_pstate->crtc_w *
 					       adjhdisplay,
@@ -332,7 +334,6 @@
 	struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
 	struct drm_framebuffer *fb = state->fb;
 	struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
-	u32 subpixel_src_mask = (1 << 16) - 1;
 	int num_planes = fb->format->num_planes;
 	struct drm_crtc_state *crtc_state;
 	u32 h_subsample = fb->format->hsub;
@@ -354,18 +355,15 @@
 	for (i = 0; i < num_planes; i++)
 		vc4_state->offsets[i] = bo->paddr + fb->offsets[i];
 
-	/* We don't support subpixel source positioning for scaling. */
-	if ((state->src.x1 & subpixel_src_mask) ||
-	    (state->src.x2 & subpixel_src_mask) ||
-	    (state->src.y1 & subpixel_src_mask) ||
-	    (state->src.y2 & subpixel_src_mask)) {
-		return -EINVAL;
-	}
-
-	vc4_state->src_x = state->src.x1 >> 16;
-	vc4_state->src_y = state->src.y1 >> 16;
-	vc4_state->src_w[0] = (state->src.x2 - state->src.x1) >> 16;
-	vc4_state->src_h[0] = (state->src.y2 - state->src.y1) >> 16;
+	/*
+	 * We don't support subpixel source positioning for scaling,
+	 * but fractional coordinates can be generated by clipping
+	 * so just round for now
+	 */
+	vc4_state->src_x = DIV_ROUND_CLOSEST(state->src.x1, 1 << 16);
+	vc4_state->src_y = DIV_ROUND_CLOSEST(state->src.y1, 1 << 16);
+	vc4_state->src_w[0] = DIV_ROUND_CLOSEST(state->src.x2, 1 << 16) - vc4_state->src_x;
+	vc4_state->src_h[0] = DIV_ROUND_CLOSEST(state->src.y2, 1 << 16) - vc4_state->src_y;
 
 	vc4_state->crtc_x = state->dst.x1;
 	vc4_state->crtc_y = state->dst.y1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_regs.h
@@ -220,6 +220,12 @@
 #define SCALER_DISPCTRL                         0x00000000
 /* Global register for clock gating the HVS */
 # define SCALER_DISPCTRL_ENABLE			BIT(31)
+# define SCALER_DISPCTRL_PANIC0_MASK		VC4_MASK(25, 24)
+# define SCALER_DISPCTRL_PANIC0_SHIFT		24
+# define SCALER_DISPCTRL_PANIC1_MASK		VC4_MASK(27, 26)
+# define SCALER_DISPCTRL_PANIC1_SHIFT		26
+# define SCALER_DISPCTRL_PANIC2_MASK		VC4_MASK(29, 28)
+# define SCALER_DISPCTRL_PANIC2_SHIFT		28
 # define SCALER_DISPCTRL_DSP3_MUX_MASK		VC4_MASK(19, 18)
 # define SCALER_DISPCTRL_DSP3_MUX_SHIFT		18
 
@@ -379,8 +385,6 @@
 # define SCALER_DISPSTATX_MODE_EOF		3
 # define SCALER_DISPSTATX_FULL			BIT(29)
 # define SCALER_DISPSTATX_EMPTY			BIT(28)
-# define SCALER_DISPSTATX_FRAME_COUNT_MASK	VC4_MASK(17, 12)
-# define SCALER_DISPSTATX_FRAME_COUNT_SHIFT	12
 # define SCALER_DISPSTATX_LINE_MASK		VC4_MASK(11, 0)
 # define SCALER_DISPSTATX_LINE_SHIFT		0
 
@@ -403,9 +407,15 @@
 						 (x) * (SCALER_DISPBKGND1 - \
 							SCALER_DISPBKGND0))
 #define SCALER_DISPSTAT1                        0x00000058
+# define SCALER_DISPSTAT1_FRCNT0_MASK		VC4_MASK(23, 18)
+# define SCALER_DISPSTAT1_FRCNT0_SHIFT		18
+# define SCALER_DISPSTAT1_FRCNT1_MASK		VC4_MASK(17, 12)
+# define SCALER_DISPSTAT1_FRCNT1_SHIFT		12
+
 #define SCALER_DISPSTATX(x)			(SCALER_DISPSTAT0 +        \
 						 (x) * (SCALER_DISPSTAT1 - \
 							SCALER_DISPSTAT0))
+
 #define SCALER_DISPBASE1                        0x0000005c
 #define SCALER_DISPBASEX(x)			(SCALER_DISPBASE0 +        \
 						 (x) * (SCALER_DISPBASE1 - \
@@ -415,7 +425,11 @@
 						 (x) * (SCALER_DISPCTRL1 - \
 							SCALER_DISPCTRL0))
 #define SCALER_DISPBKGND2                       0x00000064
+
 #define SCALER_DISPSTAT2                        0x00000068
+# define SCALER_DISPSTAT2_FRCNT2_MASK		VC4_MASK(17, 12)
+# define SCALER_DISPSTAT2_FRCNT2_SHIFT		12
+
 #define SCALER_DISPBASE2                        0x0000006c
 #define SCALER_DISPALPHA2                       0x00000070
 #define SCALER_GAMADDR                          0x00000078
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_txp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_txp.c
@@ -298,12 +298,18 @@
 	if (WARN_ON(i == ARRAY_SIZE(drm_fmts)))
 		return;
 
-	ctrl = TXP_GO | TXP_VSTART_AT_EOF | TXP_EI |
+	ctrl = TXP_GO | TXP_EI |
 	       VC4_SET_FIELD(0xf, TXP_BYTE_ENABLE) |
 	       VC4_SET_FIELD(txp_fmts[i], TXP_FORMAT);
 
 	if (fb->format->has_alpha)
 		ctrl |= TXP_ALPHA_ENABLE;
+	else
+		/*
+		 * If TXP_ALPHA_ENABLE isn't set and TXP_ALPHA_INVERT is, the
+		 * hardware will force the output padding to be 0xff.
+		 */
+		ctrl |= TXP_ALPHA_INVERT;
 
 	gem = drm_fb_cma_get_gem_obj(fb, 0);
 	TXP_WRITE(TXP_DST_PTR, gem->paddr + fb->offsets[0]);
@@ -391,7 +397,6 @@
 {
 	struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state,
 									  crtc);
-	struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
 	int ret;
 
 	ret = vc4_hvs_atomic_check(crtc, state);
@@ -399,7 +404,6 @@
 		return ret;
 
 	crtc_state->no_vblank = true;
-	vc4_state->feed_txp = true;
 
 	return 0;
 }
@@ -437,6 +441,7 @@
 
 static const struct drm_crtc_helper_funcs vc4_txp_crtc_helper_funcs = {
 	.atomic_check	= vc4_txp_atomic_check,
+	.atomic_begin	= vc4_hvs_atomic_begin,
 	.atomic_flush	= vc4_hvs_atomic_flush,
 	.atomic_enable	= vc4_txp_atomic_enable,
 	.atomic_disable	= vc4_txp_atomic_disable,
@@ -482,6 +487,7 @@
 
 	vc4_crtc->pdev = pdev;
 	vc4_crtc->data = &vc4_txp_crtc_data;
+	vc4_crtc->feeds_txp = true;
 
 	txp->pdev = pdev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vc4/vc4_vec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vc4/vc4_vec.c
@@ -256,7 +256,7 @@
 static const struct drm_display_mode ntsc_mode = {
 	DRM_MODE("720x480", DRM_MODE_TYPE_DRIVER, 13500,
 		 720, 720 + 14, 720 + 14 + 64, 720 + 14 + 64 + 60, 0,
-		 480, 480 + 3, 480 + 3 + 3, 480 + 3 + 3 + 16, 0,
+		 480, 480 + 7, 480 + 7 + 6, 525, 0,
 		 DRM_MODE_FLAG_INTERLACE)
 };
 
@@ -278,7 +278,7 @@
 static const struct drm_display_mode pal_mode = {
 	DRM_MODE("720x576", DRM_MODE_TYPE_DRIVER, 13500,
 		 720, 720 + 20, 720 + 20 + 64, 720 + 20 + 64 + 60, 0,
-		 576, 576 + 2, 576 + 2 + 3, 576 + 2 + 3 + 20, 0,
+		 576, 576 + 4, 576 + 4 + 6, 625, 0,
 		 DRM_MODE_FLAG_INTERLACE)
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vgem/vgem_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vgem/vgem_fence.c
@@ -248,4 +248,5 @@
 {
 	idr_for_each(&vfile->fence_idr, __vgem_fence_idr_fini, vfile);
 	idr_destroy(&vfile->fence_idr);
+	mutex_destroy(&vfile->fence_mutex);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/virtio/virtgpu_display.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/virtio/virtgpu_display.c
@@ -179,6 +179,8 @@
 		DRM_DEBUG("add mode: %dx%d\n", width, height);
 		mode = drm_cvt_mode(connector->dev, width, height, 60,
 				    false, false, false);
+		if (!mode)
+			return count;
 		mode->type |= DRM_MODE_TYPE_PREFERRED;
 		drm_mode_probed_add(connector, mode);
 		count++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/virtio/virtgpu_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/virtio/virtgpu_gem.c
@@ -248,6 +248,9 @@
 {
 	u32 i;
 
+	if (!objs)
+		return;
+
 	for (i = 0; i < objs->nents; i++)
 		drm_gem_object_put(objs->objs[i]);
 	virtio_gpu_array_free(objs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/virtio/virtgpu_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/virtio/virtgpu_ioctl.c
@@ -292,10 +292,18 @@
 		drm_gem_object_release(obj);
 		return ret;
 	}
-	drm_gem_object_put(obj);
 
 	rc->res_handle = qobj->hw_res_handle; /* similiar to a VM address */
 	rc->bo_handle = handle;
+
+	/*
+	 * The handle owns the reference now.  But we must drop our
+	 * remaining reference *after* we no longer need to dereference
+	 * the obj.  Otherwise userspace could guess the handle and
+	 * race closing it from another thread.
+	 */
+	drm_gem_object_put(obj);
+
 	return 0;
 }
 
@@ -512,8 +520,10 @@
 	spin_unlock(&vgdev->display_info_lock);
 
 	/* not in cache - need to talk to hw */
-	virtio_gpu_cmd_get_capset(vgdev, found_valid, args->cap_set_ver,
-				  &cache_ent);
+	ret = virtio_gpu_cmd_get_capset(vgdev, found_valid, args->cap_set_ver,
+					&cache_ent);
+	if (ret)
+		return ret;
 	virtio_gpu_notify(vgdev);
 
 copy_exit:
@@ -654,11 +664,18 @@
 		drm_gem_object_release(obj);
 		return ret;
 	}
-	drm_gem_object_put(obj);
 
 	rc_blob->res_handle = bo->hw_res_handle;
 	rc_blob->bo_handle = handle;
 
+	/*
+	 * The handle owns the reference now.  But we must drop our
+	 * remaining reference *after* we no longer need to dereference
+	 * the obj.  Otherwise userspace could guess the handle and
+	 * race closing it from another thread.
+	 */
+	drm_gem_object_put(obj);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/virtio/virtgpu_object.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/virtio/virtgpu_object.c
@@ -79,10 +79,10 @@
 			sg_free_table(shmem->pages);
 			kfree(shmem->pages);
 			shmem->pages = NULL;
-			drm_gem_shmem_unpin(&bo->base.base);
+			drm_gem_shmem_unpin(&bo->base);
 		}
 
-		drm_gem_shmem_free_object(&bo->base.base);
+		drm_gem_shmem_free(&bo->base);
 	} else if (virtio_gpu_is_vram(bo)) {
 		struct virtio_gpu_object_vram *vram = to_virtio_gpu_vram(bo);
 
@@ -116,15 +116,14 @@
 	.free = virtio_gpu_free_object,
 	.open = virtio_gpu_gem_object_open,
 	.close = virtio_gpu_gem_object_close,
-
-	.print_info = drm_gem_shmem_print_info,
+	.print_info = drm_gem_shmem_object_print_info,
 	.export = virtgpu_gem_prime_export,
-	.pin = drm_gem_shmem_pin,
-	.unpin = drm_gem_shmem_unpin,
-	.get_sg_table = drm_gem_shmem_get_sg_table,
-	.vmap = drm_gem_shmem_vmap,
-	.vunmap = drm_gem_shmem_vunmap,
-	.mmap = drm_gem_shmem_mmap,
+	.pin = drm_gem_shmem_object_pin,
+	.unpin = drm_gem_shmem_object_unpin,
+	.get_sg_table = drm_gem_shmem_object_get_sg_table,
+	.vmap = drm_gem_shmem_object_vmap,
+	.vunmap = drm_gem_shmem_object_vunmap,
+	.mmap = drm_gem_shmem_object_mmap,
 };
 
 bool virtio_gpu_is_shmem(struct virtio_gpu_object *bo)
@@ -157,7 +156,7 @@
 	struct scatterlist *sg;
 	int si, ret;
 
-	ret = drm_gem_shmem_pin(&bo->base.base);
+	ret = drm_gem_shmem_pin(&bo->base);
 	if (ret < 0)
 		return -EINVAL;
 
@@ -167,10 +166,12 @@
 	 * dma-ops. This is discouraged for other drivers, but should be fine
 	 * since virtio_gpu doesn't support dma-buf import from other devices.
 	 */
-	shmem->pages = drm_gem_shmem_get_sg_table(&bo->base.base);
-	if (!shmem->pages) {
-		drm_gem_shmem_unpin(&bo->base.base);
-		return -EINVAL;
+	shmem->pages = drm_gem_shmem_get_sg_table(&bo->base);
+	if (IS_ERR(shmem->pages)) {
+		drm_gem_shmem_unpin(&bo->base);
+		ret = PTR_ERR(shmem->pages);
+		shmem->pages = NULL;
+		return ret;
 	}
 
 	if (use_dma_api) {
@@ -248,6 +249,8 @@
 
 	ret = virtio_gpu_object_shmem_init(vgdev, bo, &ents, &nents);
 	if (ret != 0) {
+		if (fence)
+			virtio_gpu_array_unlock_resv(objs);
 		virtio_gpu_array_put_free(objs);
 		virtio_gpu_free_object(&shmem_obj->base);
 		return ret;
@@ -277,6 +280,6 @@
 err_put_id:
 	virtio_gpu_resource_id_put(vgdev, bo->hw_res_handle);
 err_free_gem:
-	drm_gem_shmem_free_object(&shmem_obj->base);
+	drm_gem_shmem_free(shmem_obj);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/virtio/virtgpu_plane.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/virtio/virtgpu_plane.c
@@ -265,14 +265,14 @@
 }
 
 static void virtio_gpu_plane_cleanup_fb(struct drm_plane *plane,
-					struct drm_plane_state *old_state)
+					struct drm_plane_state *state)
 {
 	struct virtio_gpu_framebuffer *vgfb;
 
-	if (!plane->state->fb)
+	if (!state->fb)
 		return;
 
-	vgfb = to_virtio_gpu_framebuffer(plane->state->fb);
+	vgfb = to_virtio_gpu_framebuffer(state->fb);
 	if (vgfb->fence) {
 		dma_fence_put(&vgfb->fence->f);
 		vgfb->fence = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/virtio/virtgpu_vq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/virtio/virtgpu_vq.c
@@ -91,9 +91,7 @@
 {
 	struct virtio_gpu_vbuffer *vbuf;
 
-	vbuf = kmem_cache_zalloc(vgdev->vbufs, GFP_KERNEL);
-	if (!vbuf)
-		return ERR_PTR(-ENOMEM);
+	vbuf = kmem_cache_zalloc(vgdev->vbufs, GFP_KERNEL | __GFP_NOFAIL);
 
 	BUG_ON(size > MAX_INLINE_CMD_SIZE ||
 	       size < sizeof(struct virtio_gpu_ctrl_hdr));
@@ -147,10 +145,6 @@
 
 	vbuf = virtio_gpu_get_vbuf(vgdev, cmd_size,
 				   resp_size, resp_buf, cb);
-	if (IS_ERR(vbuf)) {
-		*vbuffer_p = NULL;
-		return ERR_CAST(vbuf);
-	}
 	*vbuffer_p = vbuf;
 	return (struct virtio_gpu_command *)vbuf->buf;
 }
@@ -610,7 +604,7 @@
 	bool use_dma_api = !virtio_has_dma_quirk(vgdev->vdev);
 	struct virtio_gpu_object_shmem *shmem = to_virtio_gpu_shmem(bo);
 
-	if (use_dma_api)
+	if (virtio_gpu_is_shmem(bo) && use_dma_api)
 		dma_sync_sgtable_for_device(vgdev->vdev->dev.parent,
 					    shmem->pages, DMA_TO_DEVICE);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vkms/vkms_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vkms/vkms_drv.c
@@ -57,7 +57,8 @@
 {
 	struct vkms_device *vkms = drm_device_to_vkms_device(dev);
 
-	destroy_workqueue(vkms->output.composer_workq);
+	if (vkms->output.composer_workq)
+		destroy_workqueue(vkms->output.composer_workq);
 }
 
 static void vkms_atomic_commit_tail(struct drm_atomic_state *old_state)
@@ -218,19 +219,26 @@
 
 static int __init vkms_init(void)
 {
+	int ret;
 	struct vkms_config *config;
 
 	config = kmalloc(sizeof(*config), GFP_KERNEL);
 	if (!config)
 		return -ENOMEM;
 
-	default_config = config;
-
 	config->cursor = enable_cursor;
 	config->writeback = enable_writeback;
 	config->overlay = enable_overlay;
 
-	return vkms_create(config);
+	ret = vkms_create(config);
+	if (ret) {
+		kfree(config);
+		return ret;
+	}
+
+	default_config = config;
+
+	return 0;
 }
 
 static void vkms_destroy(struct vkms_config *config)
@@ -254,9 +262,10 @@
 
 static void __exit vkms_exit(void)
 {
-	if (default_config->dev)
-		vkms_destroy(default_config);
+	if (!default_config)
+		return;
 
+	vkms_destroy(default_config);
 	kfree(default_config);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/Kconfig
@@ -2,7 +2,7 @@
 config DRM_VMWGFX
 	tristate "DRM driver for VMware Virtual GPU"
 	depends on DRM && PCI && MMU
-	depends on X86 || ARM64
+	depends on (X86 && HYPERVISOR_GUEST) || ARM64
 	select DRM_TTM
 	select MAPPING_DIRTY_HELPERS
 	# Only needed for the transitional use of drm_crtc_init - can be removed
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/Makefile
@@ -9,9 +9,8 @@
 	    vmwgfx_cotable.o vmwgfx_so.o vmwgfx_binding.o vmwgfx_msg.o \
 	    vmwgfx_simple_resource.o vmwgfx_va.o vmwgfx_blit.o \
 	    vmwgfx_validation.o vmwgfx_page_dirty.o vmwgfx_streamoutput.o \
-            vmwgfx_devcaps.o ttm_object.o ttm_memory.o
+	    vmwgfx_devcaps.o ttm_object.o ttm_memory.o vmwgfx_system_manager.o
 
 vmwgfx-$(CONFIG_DRM_FBDEV_EMULATION) += vmwgfx_fb.o
-vmwgfx-$(CONFIG_TRANSPARENT_HUGEPAGE) += vmwgfx_thp.o
 
 obj-$(CONFIG_DRM_VMWGFX) := vmwgfx.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/ttm_memory.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/ttm_memory.c
@@ -34,7 +34,6 @@
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/slab.h>
-#include <linux/swap.h>
 
 #include <drm/drm_device.h>
 #include <drm/drm_file.h>
@@ -173,69 +172,7 @@
 	.sysfs_ops = &ttm_mem_zone_ops,
 	.default_attrs = ttm_mem_zone_attrs,
 };
-
-static struct attribute ttm_mem_global_lower_mem_limit = {
-	.name = "lower_mem_limit",
-	.mode = S_IRUGO | S_IWUSR
-};
-
-static ssize_t ttm_mem_global_show(struct kobject *kobj,
-				 struct attribute *attr,
-				 char *buffer)
-{
-	struct ttm_mem_global *glob =
-		container_of(kobj, struct ttm_mem_global, kobj);
-	uint64_t val = 0;
-
-	spin_lock(&glob->lock);
-	val = glob->lower_mem_limit;
-	spin_unlock(&glob->lock);
-	/* convert from number of pages to KB */
-	val <<= (PAGE_SHIFT - 10);
-	return snprintf(buffer, PAGE_SIZE, "%llu\n",
-			(unsigned long long) val);
-}
-
-static ssize_t ttm_mem_global_store(struct kobject *kobj,
-				  struct attribute *attr,
-				  const char *buffer,
-				  size_t size)
-{
-	int chars;
-	uint64_t val64;
-	unsigned long val;
-	struct ttm_mem_global *glob =
-		container_of(kobj, struct ttm_mem_global, kobj);
-
-	chars = sscanf(buffer, "%lu", &val);
-	if (chars == 0)
-		return size;
-
-	val64 = val;
-	/* convert from KB to number of pages */
-	val64 >>= (PAGE_SHIFT - 10);
-
-	spin_lock(&glob->lock);
-	glob->lower_mem_limit = val64;
-	spin_unlock(&glob->lock);
-
-	return size;
-}
-
-static struct attribute *ttm_mem_global_attrs[] = {
-	&ttm_mem_global_lower_mem_limit,
-	NULL
-};
-
-static const struct sysfs_ops ttm_mem_global_ops = {
-	.show = &ttm_mem_global_show,
-	.store = &ttm_mem_global_store,
-};
-
-static struct kobj_type ttm_mem_glob_kobj_type = {
-	.sysfs_ops = &ttm_mem_global_ops,
-	.default_attrs = ttm_mem_global_attrs,
-};
+static struct kobj_type ttm_mem_glob_kobj_type = {0};
 
 static bool ttm_zones_above_swap_target(struct ttm_mem_global *glob,
 					bool from_wq, uint64_t extra)
@@ -435,11 +372,6 @@
 
 	si_meminfo(&si);
 
-	spin_lock(&glob->lock);
-	/* set it as 0 by default to keep original behavior of OOM */
-	glob->lower_mem_limit = 0;
-	spin_unlock(&glob->lock);
-
 	ret = ttm_mem_init_kernel_zone(glob, &si);
 	if (unlikely(ret != 0))
 		goto out_no_zone;
@@ -527,35 +459,6 @@
 }
 EXPORT_SYMBOL(ttm_mem_global_free);
 
-/*
- * check if the available mem is under lower memory limit
- *
- * a. if no swap disk at all or free swap space is under swap_mem_limit
- * but available system mem is bigger than sys_mem_limit, allow TTM
- * allocation;
- *
- * b. if the available system mem is less than sys_mem_limit but free
- * swap disk is bigger than swap_mem_limit, allow TTM allocation.
- */
-bool
-ttm_check_under_lowerlimit(struct ttm_mem_global *glob,
-			uint64_t num_pages,
-			struct ttm_operation_ctx *ctx)
-{
-	int64_t available;
-
-	/* We allow over commit during suspend */
-	if (ctx->force_alloc)
-		return false;
-
-	available = get_nr_swap_pages() + si_mem_available();
-	available -= num_pages;
-	if (available < glob->lower_mem_limit)
-		return true;
-
-	return false;
-}
-
 static int ttm_mem_global_reserve(struct ttm_mem_global *glob,
 				  struct ttm_mem_zone *single_zone,
 				  uint64_t amount, bool reserve)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/ttm_memory.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/ttm_memory.h
@@ -50,8 +50,6 @@
  * @work: The workqueue callback for the shrink queue.
  * @lock: Lock to protect the @shrink - and the memory accounting members,
  * that is, essentially the whole structure with some exceptions.
- * @lower_mem_limit: include lower limit of swap space and lower limit of
- * system memory.
  * @zones: Array of pointers to accounting zones.
  * @num_zones: Number of populated entries in the @zones array.
  * @zone_kernel: Pointer to the kernel zone.
@@ -69,7 +67,6 @@
 	struct workqueue_struct *swap_queue;
 	struct work_struct work;
 	spinlock_t lock;
-	uint64_t lower_mem_limit;
 	struct ttm_mem_zone *zones[TTM_MEM_MAX_ZONES];
 	unsigned int num_zones;
 	struct ttm_mem_zone *zone_kernel;
@@ -91,6 +88,5 @@
 void ttm_mem_global_free_page(struct ttm_mem_global *glob,
 			      struct page *page, uint64_t size);
 size_t ttm_round_pot(size_t size);
-bool ttm_check_under_lowerlimit(struct ttm_mem_global *glob, uint64_t num_pages,
-				struct ttm_operation_ctx *ctx);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_cmd.c
@@ -145,6 +145,13 @@
 		 (unsigned int) max,
 		 (unsigned int) min,
 		 (unsigned int) fifo->capabilities);
+
+	if (unlikely(min >= max)) {
+		drm_warn(&dev_priv->drm,
+			 "FIFO memory is not usable. Driver failed to initialize.");
+		return ERR_PTR(-ENXIO);
+	}
+
 	return fifo;
 }
 
@@ -521,7 +528,7 @@
 		*seqno = atomic_add_return(1, &dev_priv->marker_seq);
 	} while (*seqno == 0);
 
-	if (!(vmw_fifo_caps(dev_priv) & SVGA_FIFO_CAP_FENCE)) {
+	if (!vmw_has_fences(dev_priv)) {
 
 		/*
 		 * Don't request hardware to send a fence. The
@@ -668,11 +675,14 @@
  */
 bool vmw_cmd_supported(struct vmw_private *vmw)
 {
-	if ((vmw->capabilities & (SVGA_CAP_COMMAND_BUFFERS |
-				  SVGA_CAP_CMD_BUFFERS_2)) != 0)
-		return true;
+	bool has_cmdbufs =
+		(vmw->capabilities & (SVGA_CAP_COMMAND_BUFFERS |
+				      SVGA_CAP_CMD_BUFFERS_2)) != 0;
+	if (vmw_is_svga_v3(vmw))
+		return (has_cmdbufs &&
+			(vmw->capabilities & SVGA_CAP_GBOBJECTS) != 0);
 	/*
 	 * We have FIFO cmd's
 	 */
-	return vmw->fifo_mem != NULL;
+	return has_cmdbufs || vmw->fifo_mem != NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_drv.c
@@ -707,23 +707,15 @@
 static int vmw_vram_manager_init(struct vmw_private *dev_priv)
 {
 	int ret;
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-	ret = vmw_thp_init(dev_priv);
-#else
 	ret = ttm_range_man_init(&dev_priv->bdev, TTM_PL_VRAM, false,
 				 dev_priv->vram_size >> PAGE_SHIFT);
-#endif
 	ttm_resource_manager_set_used(ttm_manager_type(&dev_priv->bdev, TTM_PL_VRAM), false);
 	return ret;
 }
 
 static void vmw_vram_manager_fini(struct vmw_private *dev_priv)
 {
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-	vmw_thp_fini(dev_priv);
-#else
 	ttm_range_man_fini(&dev_priv->bdev, TTM_PL_VRAM);
-#endif
 }
 
 static int vmw_setup_pci_resources(struct vmw_private *dev,
@@ -912,13 +904,6 @@
 				vmw_read(dev_priv,
 					 SVGA_REG_SUGGESTED_GBOBJECT_MEM_SIZE_KB);
 
-		/*
-		 * Workaround for low memory 2D VMs to compensate for the
-		 * allocation taken by fbdev
-		 */
-		if (!(dev_priv->capabilities & SVGA_CAP_3D))
-			mem_size *= 3;
-
 		dev_priv->max_mob_pages = mem_size * 1024 / PAGE_SIZE;
 		dev_priv->max_primary_mem =
 			vmw_read(dev_priv, SVGA_REG_MAX_PRIMARY_MEM);
@@ -1071,6 +1056,12 @@
 				 "3D will be disabled.\n");
 			dev_priv->has_mob = false;
 		}
+		if (vmw_sys_man_init(dev_priv) != 0) {
+			drm_info(&dev_priv->drm,
+				 "No MOB page table memory available. "
+				 "3D will be disabled.\n");
+			dev_priv->has_mob = false;
+		}
 	}
 
 	if (dev_priv->has_mob && (dev_priv->capabilities & SVGA_CAP_DX)) {
@@ -1121,8 +1112,10 @@
 	vmw_overlay_close(dev_priv);
 	vmw_kms_close(dev_priv);
 out_no_kms:
-	if (dev_priv->has_mob)
+	if (dev_priv->has_mob) {
 		vmw_gmrid_man_fini(dev_priv, VMW_PL_MOB);
+		vmw_sys_man_fini(dev_priv);
+	}
 	if (dev_priv->has_gmr)
 		vmw_gmrid_man_fini(dev_priv, VMW_PL_GMR);
 	vmw_devcaps_destroy(dev_priv);
@@ -1172,8 +1165,10 @@
 		vmw_gmrid_man_fini(dev_priv, VMW_PL_GMR);
 
 	vmw_release_device_early(dev_priv);
-	if (dev_priv->has_mob)
+	if (dev_priv->has_mob) {
 		vmw_gmrid_man_fini(dev_priv, VMW_PL_MOB);
+		vmw_sys_man_fini(dev_priv);
+	}
 	vmw_devcaps_destroy(dev_priv);
 	vmw_vram_manager_fini(dev_priv);
 	ttm_device_fini(&dev_priv->bdev);
@@ -1617,34 +1612,40 @@
 
 	ret = drm_aperture_remove_conflicting_pci_framebuffers(pdev, &driver);
 	if (ret)
-		return ret;
+		goto out_error;
 
 	ret = pcim_enable_device(pdev);
 	if (ret)
-		return ret;
+		goto out_error;
 
 	vmw = devm_drm_dev_alloc(&pdev->dev, &driver,
 				 struct vmw_private, drm);
-	if (IS_ERR(vmw))
-		return PTR_ERR(vmw);
+	if (IS_ERR(vmw)) {
+		ret = PTR_ERR(vmw);
+		goto out_error;
+	}
 
 	pci_set_drvdata(pdev, &vmw->drm);
 
 	ret = ttm_mem_global_init(&ttm_mem_glob, &pdev->dev);
 	if (ret)
-		return ret;
+		goto out_error;
 
 	ret = vmw_driver_load(vmw, ent->device);
 	if (ret)
-		return ret;
+		goto out_release;
 
 	ret = drm_dev_register(&vmw->drm, 0);
-	if (ret) {
-		vmw_driver_unload(&vmw->drm);
-		return ret;
-	}
+	if (ret)
+		goto out_unload;
 
 	return 0;
+out_unload:
+	vmw_driver_unload(&vmw->drm);
+out_release:
+	ttm_mem_global_release(&ttm_mem_glob);
+out_error:
+	return ret;
 }
 
 static int __init vmwgfx_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_drv.h
@@ -59,11 +59,8 @@
 #define VMWGFX_DRIVER_MINOR 19
 #define VMWGFX_DRIVER_PATCHLEVEL 0
 #define VMWGFX_FIFO_STATIC_SIZE (1024*1024)
-#define VMWGFX_MAX_RELOCATIONS 2048
-#define VMWGFX_MAX_VALIDATIONS 2048
-#define VMWGFX_MAX_DISPLAYS 16
+#define VMWGFX_NUM_DISPLAY_UNITS 8
 #define VMWGFX_CMD_BOUNCE_INIT_SIZE 32768
-#define VMWGFX_ENABLE_SCREEN_TARGET_OTABLE 1
 
 #define VMWGFX_PCI_ID_SVGA2              0x0405
 #define VMWGFX_PCI_ID_SVGA3              0x0406
@@ -74,7 +71,7 @@
 #define VMWGFX_NUM_GB_CONTEXT 256
 #define VMWGFX_NUM_GB_SHADER 20000
 #define VMWGFX_NUM_GB_SURFACE 32768
-#define VMWGFX_NUM_GB_SCREEN_TARGET VMWGFX_MAX_DISPLAYS
+#define VMWGFX_NUM_GB_SCREEN_TARGET VMWGFX_NUM_DISPLAY_UNITS
 #define VMWGFX_NUM_DXCONTEXT 256
 #define VMWGFX_NUM_DXQUERY 512
 #define VMWGFX_NUM_MOB (VMWGFX_NUM_GB_CONTEXT +\
@@ -82,8 +79,9 @@
 			VMWGFX_NUM_GB_SURFACE +\
 			VMWGFX_NUM_GB_SCREEN_TARGET)
 
-#define VMW_PL_GMR (TTM_PL_PRIV + 0)
-#define VMW_PL_MOB (TTM_PL_PRIV + 1)
+#define VMW_PL_GMR      (TTM_PL_PRIV + 0)
+#define VMW_PL_MOB      (TTM_PL_PRIV + 1)
+#define VMW_PL_SYSTEM   (TTM_PL_PRIV + 2)
 
 #define VMW_RES_CONTEXT ttm_driver_type0
 #define VMW_RES_SURFACE ttm_driver_type1
@@ -1039,7 +1037,6 @@
 extern struct ttm_placement vmw_vram_sys_placement;
 extern struct ttm_placement vmw_vram_gmr_placement;
 extern struct ttm_placement vmw_sys_placement;
-extern struct ttm_placement vmw_evictable_placement;
 extern struct ttm_placement vmw_srf_placement;
 extern struct ttm_placement vmw_mob_placement;
 extern struct ttm_placement vmw_nonfixed_placement;
@@ -1115,15 +1112,14 @@
 				      struct vmw_private *dev_priv,
 				      struct vmw_fence_obj **p_fence,
 				      uint32_t *p_handle);
-extern void vmw_execbuf_copy_fence_user(struct vmw_private *dev_priv,
+extern int vmw_execbuf_copy_fence_user(struct vmw_private *dev_priv,
 					struct vmw_fpriv *vmw_fp,
 					int ret,
 					struct drm_vmw_fence_rep __user
 					*user_fence_rep,
 					struct vmw_fence_obj *fence,
 					uint32_t fence_handle,
-					int32_t out_fence_fd,
-					struct sync_file *sync_file);
+					int32_t out_fence_fd);
 bool vmw_cmd_describe(const void *buf, u32 *size, char const **cmd);
 
 /**
@@ -1252,6 +1248,12 @@
 void vmw_gmrid_man_fini(struct vmw_private *dev_priv, int type);
 
 /**
+ * System memory manager
+ */
+int vmw_sys_man_init(struct vmw_private *dev_priv);
+void vmw_sys_man_fini(struct vmw_private *dev_priv);
+
+/**
  * Prime - vmwgfx_prime.c
  */
 
@@ -1550,16 +1552,7 @@
 			pgoff_t start, pgoff_t end);
 vm_fault_t vmw_bo_vm_fault(struct vm_fault *vmf);
 vm_fault_t vmw_bo_vm_mkwrite(struct vm_fault *vmf);
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-vm_fault_t vmw_bo_vm_huge_fault(struct vm_fault *vmf,
-				enum page_entry_size pe_size);
-#endif
 
-/* Transparent hugepage support - vmwgfx_thp.c */
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-extern int vmw_thp_init(struct vmw_private *dev_priv);
-void vmw_thp_fini(struct vmw_private *dev_priv);
-#endif
 
 /**
  * VMW_DEBUG_KMS - Debug output for kernel mode-setting
@@ -1684,4 +1677,24 @@
 		outl(status, vmw->io_start + SVGA_IRQSTATUS_PORT);
 }
 
+static inline bool vmw_has_fences(struct vmw_private *vmw)
+{
+	if ((vmw->capabilities & (SVGA_CAP_COMMAND_BUFFERS |
+				  SVGA_CAP_CMD_BUFFERS_2)) != 0)
+		return true;
+	return (vmw_fifo_caps(vmw) & SVGA_FIFO_CAP_FENCE) != 0;
+}
+
+static inline bool vmw_shadertype_is_valid(enum vmw_sm_type shader_model,
+					   u32 shader_type)
+{
+	SVGA3dShaderType max_allowed = SVGA3D_SHADERTYPE_PREDX_MAX;
+
+	if (shader_model >= VMW_SM_5)
+		max_allowed = SVGA3D_SHADERTYPE_MAX;
+	else if (shader_model >= VMW_SM_4)
+		max_allowed = SVGA3D_SHADERTYPE_DX10_MAX;
+	return shader_type >= SVGA3D_SHADERTYPE_MIN && shader_type < max_allowed;
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_execbuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_execbuf.c
@@ -472,7 +472,7 @@
 	    vmw_res_type(ctx) == vmw_res_dx_context) {
 		for (i = 0; i < cotable_max; ++i) {
 			res = vmw_context_cotable(ctx, i);
-			if (IS_ERR(res))
+			if (IS_ERR_OR_NULL(res))
 				continue;
 
 			ret = vmw_execbuf_res_noctx_val_add(sw_context, res,
@@ -1277,6 +1277,8 @@
 		return -EINVAL;
 
 	cotable_res = vmw_context_cotable(ctx_node->ctx, SVGA_COTABLE_DXQUERY);
+	if (IS_ERR_OR_NULL(cotable_res))
+		return cotable_res ? PTR_ERR(cotable_res) : -EINVAL;
 	ret = vmw_cotable_notify(cotable_res, cmd->body.queryId);
 
 	return ret;
@@ -1632,7 +1634,7 @@
 {
 	VMW_DECLARE_CMD_VAR(*cmd, SVGA3dCmdSetTextureState);
 	SVGA3dTextureState *last_state = (SVGA3dTextureState *)
-	  ((unsigned long) header + header->size + sizeof(header));
+	  ((unsigned long) header + header->size + sizeof(*header));
 	SVGA3dTextureState *cur_state = (SVGA3dTextureState *)
 		((unsigned long) header + sizeof(*cmd));
 	struct vmw_resource *ctx;
@@ -2003,7 +2005,7 @@
 
 	cmd = container_of(header, typeof(*cmd), header);
 
-	if (cmd->body.type >= SVGA3D_SHADERTYPE_PREDX_MAX) {
+	if (!vmw_shadertype_is_valid(VMW_SM_LEGACY, cmd->body.type)) {
 		VMW_DEBUG_USER("Illegal shader type %u.\n",
 			       (unsigned int) cmd->body.type);
 		return -EINVAL;
@@ -2125,8 +2127,6 @@
 				      SVGA3dCmdHeader *header)
 {
 	VMW_DECLARE_CMD_VAR(*cmd, SVGA3dCmdDXSetSingleConstantBuffer);
-	SVGA3dShaderType max_shader_num = has_sm5_context(dev_priv) ?
-		SVGA3D_NUM_SHADERTYPE : SVGA3D_NUM_SHADERTYPE_DX10;
 
 	struct vmw_resource *res = NULL;
 	struct vmw_ctx_validation_info *ctx_node = VMW_GET_CTX_NODE(sw_context);
@@ -2143,6 +2143,14 @@
 	if (unlikely(ret != 0))
 		return ret;
 
+	if (!vmw_shadertype_is_valid(dev_priv->sm_type, cmd->body.type) ||
+	    cmd->body.slot >= SVGA3D_DX_MAX_CONSTBUFFERS) {
+		VMW_DEBUG_USER("Illegal const buffer shader %u slot %u.\n",
+			       (unsigned int) cmd->body.type,
+			       (unsigned int) cmd->body.slot);
+		return -EINVAL;
+	}
+
 	binding.bi.ctx = ctx_node->ctx;
 	binding.bi.res = res;
 	binding.bi.bt = vmw_ctx_binding_cb;
@@ -2151,14 +2159,6 @@
 	binding.size = cmd->body.sizeInBytes;
 	binding.slot = cmd->body.slot;
 
-	if (binding.shader_slot >= max_shader_num ||
-	    binding.slot >= SVGA3D_DX_MAX_CONSTBUFFERS) {
-		VMW_DEBUG_USER("Illegal const buffer shader %u slot %u.\n",
-			       (unsigned int) cmd->body.type,
-			       (unsigned int) binding.slot);
-		return -EINVAL;
-	}
-
 	vmw_binding_add(ctx_node->staged, &binding.bi, binding.shader_slot,
 			binding.slot);
 
@@ -2179,15 +2179,13 @@
 {
 	VMW_DECLARE_CMD_VAR(*cmd, SVGA3dCmdDXSetShaderResources) =
 		container_of(header, typeof(*cmd), header);
-	SVGA3dShaderType max_allowed = has_sm5_context(dev_priv) ?
-		SVGA3D_SHADERTYPE_MAX : SVGA3D_SHADERTYPE_DX10_MAX;
 
 	u32 num_sr_view = (cmd->header.size - sizeof(cmd->body)) /
 		sizeof(SVGA3dShaderResourceViewId);
 
 	if ((u64) cmd->body.startView + (u64) num_sr_view >
 	    (u64) SVGA3D_DX_MAX_SRVIEWS ||
-	    cmd->body.type >= max_allowed) {
+	    !vmw_shadertype_is_valid(dev_priv->sm_type, cmd->body.type)) {
 		VMW_DEBUG_USER("Invalid shader binding.\n");
 		return -EINVAL;
 	}
@@ -2211,8 +2209,6 @@
 				 SVGA3dCmdHeader *header)
 {
 	VMW_DECLARE_CMD_VAR(*cmd, SVGA3dCmdDXSetShader);
-	SVGA3dShaderType max_allowed = has_sm5_context(dev_priv) ?
-		SVGA3D_SHADERTYPE_MAX : SVGA3D_SHADERTYPE_DX10_MAX;
 	struct vmw_resource *res = NULL;
 	struct vmw_ctx_validation_info *ctx_node = VMW_GET_CTX_NODE(sw_context);
 	struct vmw_ctx_bindinfo_shader binding;
@@ -2223,8 +2219,7 @@
 
 	cmd = container_of(header, typeof(*cmd), header);
 
-	if (cmd->body.type >= max_allowed ||
-	    cmd->body.type < SVGA3D_SHADERTYPE_MIN) {
+	if (!vmw_shadertype_is_valid(dev_priv->sm_type, cmd->body.type)) {
 		VMW_DEBUG_USER("Illegal shader type %u.\n",
 			       (unsigned int) cmd->body.type);
 		return -EINVAL;
@@ -2462,6 +2457,8 @@
 		return ret;
 
 	res = vmw_context_cotable(ctx_node->ctx, vmw_view_cotables[view_type]);
+	if (IS_ERR_OR_NULL(res))
+		return res ? PTR_ERR(res) : -EINVAL;
 	ret = vmw_cotable_notify(res, cmd->defined_id);
 	if (unlikely(ret != 0))
 		return ret;
@@ -2547,8 +2544,8 @@
 
 	so_type = vmw_so_cmd_to_type(header->id);
 	res = vmw_context_cotable(ctx_node->ctx, vmw_so_cotables[so_type]);
-	if (IS_ERR(res))
-		return PTR_ERR(res);
+	if (IS_ERR_OR_NULL(res))
+		return res ? PTR_ERR(res) : -EINVAL;
 	cmd = container_of(header, typeof(*cmd), header);
 	ret = vmw_cotable_notify(res, cmd->defined_id);
 
@@ -2667,6 +2664,8 @@
 		return -EINVAL;
 
 	res = vmw_context_cotable(ctx_node->ctx, SVGA_COTABLE_DXSHADER);
+	if (IS_ERR_OR_NULL(res))
+		return res ? PTR_ERR(res) : -EINVAL;
 	ret = vmw_cotable_notify(res, cmd->body.shaderId);
 	if (ret)
 		return ret;
@@ -2988,6 +2987,8 @@
 	}
 
 	res = vmw_context_cotable(ctx_node->ctx, SVGA_COTABLE_STREAMOUTPUT);
+	if (IS_ERR_OR_NULL(res))
+		return res ? PTR_ERR(res) : -EINVAL;
 	ret = vmw_cotable_notify(res, cmd->body.soid);
 	if (ret)
 		return ret;
@@ -3823,17 +3824,17 @@
  * Also if copying fails, user-space will be unable to signal the fence object
  * so we wait for it immediately, and then unreference the user-space reference.
  */
-void
+int
 vmw_execbuf_copy_fence_user(struct vmw_private *dev_priv,
 			    struct vmw_fpriv *vmw_fp, int ret,
 			    struct drm_vmw_fence_rep __user *user_fence_rep,
 			    struct vmw_fence_obj *fence, uint32_t fence_handle,
-			    int32_t out_fence_fd, struct sync_file *sync_file)
+			    int32_t out_fence_fd)
 {
 	struct drm_vmw_fence_rep fence_rep;
 
 	if (user_fence_rep == NULL)
-		return;
+		return 0;
 
 	memset(&fence_rep, 0, sizeof(fence_rep));
 
@@ -3861,20 +3862,14 @@
 	 * handle.
 	 */
 	if (unlikely(ret != 0) && (fence_rep.error == 0)) {
-		if (sync_file)
-			fput(sync_file->file);
-
-		if (fence_rep.fd != -1) {
-			put_unused_fd(fence_rep.fd);
-			fence_rep.fd = -1;
-		}
-
 		ttm_ref_object_base_unref(vmw_fp->tfile, fence_handle,
 					  TTM_REF_USAGE);
 		VMW_DEBUG_USER("Fence copy error. Syncing.\n");
 		(void) vmw_fence_obj_wait(fence, false, false,
 					  VMW_FENCE_WAIT_TIMEOUT);
 	}
+
+	return ret ? -EFAULT : 0;
 }
 
 /**
@@ -4212,16 +4207,23 @@
 
 			(void) vmw_fence_obj_wait(fence, false, false,
 						  VMW_FENCE_WAIT_TIMEOUT);
+		}
+	}
+
+	ret = vmw_execbuf_copy_fence_user(dev_priv, vmw_fpriv(file_priv), ret,
+				    user_fence_rep, fence, handle, out_fence_fd);
+
+	if (sync_file) {
+		if (ret) {
+			/* usercopy of fence failed, put the file object */
+			fput(sync_file->file);
+			put_unused_fd(out_fence_fd);
 		} else {
 			/* Link the fence with the FD created earlier */
 			fd_install(out_fence_fd, sync_file->file);
 		}
 	}
 
-	vmw_execbuf_copy_fence_user(dev_priv, vmw_fpriv(file_priv), ret,
-				    user_fence_rep, fence, handle, out_fence_fd,
-				    sync_file);
-
 	/* Don't unreference when handing fence out */
 	if (unlikely(out_fence != NULL)) {
 		*out_fence = fence;
@@ -4239,7 +4241,7 @@
 	 */
 	vmw_validation_unref_lists(&val_ctx);
 
-	return 0;
+	return ret;
 
 out_unlock_binding:
 	mutex_unlock(&dev_priv->binding_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_fb.c
@@ -316,18 +316,18 @@
 	return 0;
 }
 
-static void vmw_deferred_io(struct fb_info *info,
-			    struct list_head *pagelist)
+static void vmw_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	struct vmw_fb_par *par = info->par;
 	unsigned long start, end, min, max;
 	unsigned long flags;
-	struct page *page;
+	struct fb_deferred_io_pageref *pageref;
 	int y1, y2;
 
 	min = ULONG_MAX;
 	max = 0;
-	list_for_each_entry(page, pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *page = pageref->page;
 		start = page->index << PAGE_SHIFT;
 		end = start + PAGE_SIZE - 1;
 		min = min(min, start);
@@ -490,7 +490,7 @@
 
 static int vmw_fb_kms_framebuffer(struct fb_info *info)
 {
-	struct drm_mode_fb_cmd2 mode_cmd;
+	struct drm_mode_fb_cmd2 mode_cmd = {0};
 	struct vmw_fb_par *par = info->par;
 	struct fb_var_screeninfo *var = &info->var;
 	struct drm_framebuffer *cur_fb;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_fence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_fence.c
@@ -32,7 +32,6 @@
 #define VMW_FENCE_WRAP (1 << 31)
 
 struct vmw_fence_manager {
-	int num_fence_objects;
 	struct vmw_private *dev_priv;
 	spinlock_t lock;
 	struct list_head fence_list;
@@ -85,6 +84,22 @@
 	return container_of(fence->base.lock, struct vmw_fence_manager, lock);
 }
 
+static u32 vmw_fence_goal_read(struct vmw_private *vmw)
+{
+	if ((vmw->capabilities2 & SVGA_CAP2_EXTRA_REGS) != 0)
+		return vmw_read(vmw, SVGA_REG_FENCE_GOAL);
+	else
+		return vmw_fifo_mem_read(vmw, SVGA_FIFO_FENCE_GOAL);
+}
+
+static void vmw_fence_goal_write(struct vmw_private *vmw, u32 value)
+{
+	if ((vmw->capabilities2 & SVGA_CAP2_EXTRA_REGS) != 0)
+		vmw_write(vmw, SVGA_REG_FENCE_GOAL, value);
+	else
+		vmw_fifo_mem_write(vmw, SVGA_FIFO_FENCE_GOAL, value);
+}
+
 /*
  * Note on fencing subsystem usage of irqs:
  * Typically the vmw_fences_update function is called
@@ -111,13 +126,13 @@
 {
 	struct vmw_fence_obj *fence =
 		container_of(f, struct vmw_fence_obj, base);
-
 	struct vmw_fence_manager *fman = fman_from_fence(fence);
 
-	spin_lock(&fman->lock);
-	list_del_init(&fence->head);
-	--fman->num_fence_objects;
-	spin_unlock(&fman->lock);
+	if (!list_empty(&fence->head)) {
+		spin_lock(&fman->lock);
+		list_del_init(&fence->head);
+		spin_unlock(&fman->lock);
+	}
 	fence->destroy(fence);
 }
 
@@ -244,7 +259,6 @@
 	.release = vmw_fence_obj_destroy,
 };
 
-
 /*
  * Execute signal actions on fences recently signaled.
  * This is done from a workqueue so we don't have to execute
@@ -347,7 +361,6 @@
 		goto out_unlock;
 	}
 	list_add_tail(&fence->head, &fman->fence_list);
-	++fman->num_fence_objects;
 
 out_unlock:
 	spin_unlock(&fman->lock);
@@ -395,22 +408,21 @@
 				      u32 passed_seqno)
 {
 	u32 goal_seqno;
-	struct vmw_fence_obj *fence;
+	struct vmw_fence_obj *fence, *next_fence;
 
 	if (likely(!fman->seqno_valid))
 		return false;
 
-	goal_seqno = vmw_fifo_mem_read(fman->dev_priv, SVGA_FIFO_FENCE_GOAL);
+	goal_seqno = vmw_fence_goal_read(fman->dev_priv);
 	if (likely(passed_seqno - goal_seqno >= VMW_FENCE_WRAP))
 		return false;
 
 	fman->seqno_valid = false;
-	list_for_each_entry(fence, &fman->fence_list, head) {
+	list_for_each_entry_safe(fence, next_fence, &fman->fence_list, head) {
 		if (!list_empty(&fence->seq_passed_actions)) {
 			fman->seqno_valid = true;
-			vmw_fifo_mem_write(fman->dev_priv,
-					   SVGA_FIFO_FENCE_GOAL,
-					   fence->base.seqno);
+			vmw_fence_goal_write(fman->dev_priv,
+					     fence->base.seqno);
 			break;
 		}
 	}
@@ -442,13 +454,12 @@
 	if (dma_fence_is_signaled_locked(&fence->base))
 		return false;
 
-	goal_seqno = vmw_fifo_mem_read(fman->dev_priv, SVGA_FIFO_FENCE_GOAL);
+	goal_seqno = vmw_fence_goal_read(fman->dev_priv);
 	if (likely(fman->seqno_valid &&
 		   goal_seqno - fence->base.seqno < VMW_FENCE_WRAP))
 		return false;
 
-	vmw_fifo_mem_write(fman->dev_priv, SVGA_FIFO_FENCE_GOAL,
-			   fence->base.seqno);
+	vmw_fence_goal_write(fman->dev_priv, fence->base.seqno);
 	fman->seqno_valid = true;
 
 	return true;
@@ -1054,7 +1065,7 @@
 	}
 
 	event->event.base.type = DRM_VMW_EVENT_FENCE_SIGNALED;
-	event->event.base.length = sizeof(*event);
+	event->event.base.length = sizeof(event->event);
 	event->event.user_data = user_data;
 
 	ret = drm_event_reserve_init(dev, file_priv, &event->base, &event->event.base);
@@ -1159,7 +1170,7 @@
 	}
 
 	vmw_execbuf_copy_fence_user(dev_priv, vmw_fp, 0, user_fence_rep, fence,
-				    handle, -1, NULL);
+				    handle, -1);
 	vmw_fence_obj_unreference(&fence);
 	return 0;
 out_no_create:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_gmrid_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_gmrid_manager.c
@@ -64,8 +64,11 @@
 	ttm_resource_init(bo, place, *res);
 
 	id = ida_alloc_max(&gman->gmr_ida, gman->max_gmr_ids - 1, GFP_KERNEL);
-	if (id < 0)
+	if (id < 0) {
+		ttm_resource_fini(man, *res);
+		kfree(*res);
 		return id;
+	}
 
 	spin_lock(&gman->lock);
 
@@ -116,6 +119,7 @@
 	gman->used_gmr_pages -= (*res)->num_pages;
 	spin_unlock(&gman->lock);
 	ida_free(&gman->gmr_ida, id);
+	ttm_resource_fini(man, *res);
 	kfree(*res);
 	return -ENOSPC;
 }
@@ -129,6 +133,7 @@
 	spin_lock(&gman->lock);
 	gman->used_gmr_pages -= res->num_pages;
 	spin_unlock(&gman->lock);
+	ttm_resource_fini(man, res);
 	kfree(res);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_irq.c
@@ -32,6 +32,14 @@
 
 #define VMW_FENCE_WRAP (1 << 24)
 
+static u32 vmw_irqflag_fence_goal(struct vmw_private *vmw)
+{
+	if ((vmw->capabilities2 & SVGA_CAP2_EXTRA_REGS) != 0)
+		return SVGA_IRQFLAG_REG_FENCE_GOAL;
+	else
+		return SVGA_IRQFLAG_FENCE_GOAL;
+}
+
 /**
  * vmw_thread_fn - Deferred (process context) irq handler
  *
@@ -96,7 +104,7 @@
 		wake_up_all(&dev_priv->fifo_queue);
 
 	if ((masked_status & (SVGA_IRQFLAG_ANY_FENCE |
-			      SVGA_IRQFLAG_FENCE_GOAL)) &&
+			      vmw_irqflag_fence_goal(dev_priv))) &&
 	    !test_and_set_bit(VMW_IRQTHREAD_FENCE, dev_priv->irqthread_pending))
 		ret = IRQ_WAKE_THREAD;
 
@@ -137,8 +145,7 @@
 	if (likely(dev_priv->last_read_seqno - seqno < VMW_FENCE_WRAP))
 		return true;
 
-	if (!(vmw_fifo_caps(dev_priv) & SVGA_FIFO_CAP_FENCE) &&
-	    vmw_fifo_idle(dev_priv, seqno))
+	if (!vmw_has_fences(dev_priv) && vmw_fifo_idle(dev_priv, seqno))
 		return true;
 
 	/**
@@ -160,6 +167,7 @@
 		      unsigned long timeout)
 {
 	struct vmw_fifo_state *fifo_state = dev_priv->fifo;
+	bool fifo_down = false;
 
 	uint32_t count = 0;
 	uint32_t signal_seq;
@@ -176,12 +184,14 @@
 	 */
 
 	if (fifo_idle) {
-		down_read(&fifo_state->rwsem);
 		if (dev_priv->cman) {
 			ret = vmw_cmdbuf_idle(dev_priv->cman, interruptible,
 					      10*HZ);
 			if (ret)
 				goto out_err;
+		} else if (fifo_state) {
+			down_read(&fifo_state->rwsem);
+			fifo_down = true;
 		}
 	}
 
@@ -218,12 +228,12 @@
 		}
 	}
 	finish_wait(&dev_priv->fence_queue, &__wait);
-	if (ret == 0 && fifo_idle)
+	if (ret == 0 && fifo_idle && fifo_state)
 		vmw_fence_write(dev_priv, signal_seq);
 
 	wake_up_all(&dev_priv->fence_queue);
 out_err:
-	if (fifo_idle)
+	if (fifo_down)
 		up_read(&fifo_state->rwsem);
 
 	return ret;
@@ -266,13 +276,13 @@
 
 void vmw_goal_waiter_add(struct vmw_private *dev_priv)
 {
-	vmw_generic_waiter_add(dev_priv, SVGA_IRQFLAG_FENCE_GOAL,
+	vmw_generic_waiter_add(dev_priv, vmw_irqflag_fence_goal(dev_priv),
 			       &dev_priv->goal_queue_waiters);
 }
 
 void vmw_goal_waiter_remove(struct vmw_private *dev_priv)
 {
-	vmw_generic_waiter_remove(dev_priv, SVGA_IRQFLAG_FENCE_GOAL,
+	vmw_generic_waiter_remove(dev_priv, vmw_irqflag_fence_goal(dev_priv),
 				  &dev_priv->goal_queue_waiters);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_kms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_kms.c
@@ -186,7 +186,8 @@
 	if (cmd->dma.guest.ptr.offset % PAGE_SIZE ||
 	    box->x != 0    || box->y != 0    || box->z != 0    ||
 	    box->srcx != 0 || box->srcy != 0 || box->srcz != 0 ||
-	    box->d != 1    || box_count != 1) {
+	    box->d != 1    || box_count != 1 ||
+	    box->w > 64 || box->h > 64) {
 		/* TODO handle none page aligned offsets */
 		/* TODO handle more dst & src != 0 */
 		/* TODO handle more then one copy */
@@ -536,6 +537,7 @@
 int vmw_du_crtc_atomic_check(struct drm_crtc *crtc,
 			     struct drm_atomic_state *state)
 {
+	struct vmw_private *vmw = vmw_priv(crtc->dev);
 	struct drm_crtc_state *new_state = drm_atomic_get_new_crtc_state(state,
 									 crtc);
 	struct vmw_display_unit *du = vmw_crtc_to_du(new_state->crtc);
@@ -543,9 +545,13 @@
 	bool has_primary = new_state->plane_mask &
 			   drm_plane_mask(crtc->primary);
 
-	/* We always want to have an active plane with an active CRTC */
-	if (has_primary != new_state->enable)
-		return -EINVAL;
+	/*
+	 * This is fine in general, but broken userspace might expect
+	 * some actual rendering so give a clue as why it's blank.
+	 */
+	if (new_state->enable && !has_primary)
+		drm_dbg_driver(&vmw->drm,
+			       "CRTC without a primary plane will be blank.\n");
 
 
 	if (new_state->connector_mask != connector_mask &&
@@ -916,6 +922,15 @@
 	 * Sanity checks.
 	 */
 
+	if (!drm_any_plane_has_format(&dev_priv->drm,
+				      mode_cmd->pixel_format,
+				      mode_cmd->modifier[0])) {
+		drm_dbg(&dev_priv->drm,
+			"unsupported pixel format %p4cc / modifier 0x%llx\n",
+			&mode_cmd->pixel_format, mode_cmd->modifier[0]);
+		return -EINVAL;
+	}
+
 	/* Surface must be marked as a scanout. */
 	if (unlikely(!surface->metadata.scanout))
 		return -EINVAL;
@@ -1229,20 +1244,13 @@
 		return -EINVAL;
 	}
 
-	/* Limited framebuffer color depth support for screen objects */
-	if (dev_priv->active_display_unit == vmw_du_screen_object) {
-		switch (mode_cmd->pixel_format) {
-		case DRM_FORMAT_XRGB8888:
-		case DRM_FORMAT_ARGB8888:
-			break;
-		case DRM_FORMAT_XRGB1555:
-		case DRM_FORMAT_RGB565:
-			break;
-		default:
-			DRM_ERROR("Invalid pixel format: %p4cc\n",
-				  &mode_cmd->pixel_format);
-			return -EINVAL;
-		}
+	if (!drm_any_plane_has_format(&dev_priv->drm,
+				      mode_cmd->pixel_format,
+				      mode_cmd->modifier[0])) {
+		drm_dbg(&dev_priv->drm,
+			"unsupported pixel format %p4cc / modifier 0x%llx\n",
+			&mode_cmd->pixel_format, mode_cmd->modifier[0]);
+		return -EINVAL;
 	}
 
 	vfbd = kzalloc(sizeof(*vfbd), GFP_KERNEL);
@@ -1336,7 +1344,6 @@
 		ret = vmw_kms_new_framebuffer_surface(dev_priv, surface, &vfb,
 						      mode_cmd,
 						      is_bo_proxy);
-
 		/*
 		 * vmw_create_bo_proxy() adds a reference that is no longer
 		 * needed
@@ -1398,15 +1405,19 @@
 	ret = vmw_user_lookup_handle(dev_priv, tfile,
 				     mode_cmd->handles[0],
 				     &surface, &bo);
-	if (ret)
+	if (ret) {
+		DRM_ERROR("Invalid buffer object handle %u (0x%x).\n",
+			  mode_cmd->handles[0], mode_cmd->handles[0]);
 		goto err_out;
+	}
 
 
 	if (!bo &&
 	    !vmw_kms_srf_ok(dev_priv, mode_cmd->width, mode_cmd->height)) {
-		DRM_ERROR("Surface size cannot exceed %dx%d",
+		DRM_ERROR("Surface size cannot exceed %dx%d\n",
 			dev_priv->texture_max_width,
 			dev_priv->texture_max_height);
+		ret = -EINVAL;
 		goto err_out;
 	}
 
@@ -2284,7 +2295,7 @@
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_vmw_update_layout_arg *arg =
 		(struct drm_vmw_update_layout_arg *)data;
-	void __user *user_rects;
+	const void __user *user_rects;
 	struct drm_vmw_rect *rects;
 	struct drm_rect *drm_rects;
 	unsigned rects_size;
@@ -2297,6 +2308,8 @@
 			      def_rect.x2, def_rect.y2);
 		vmw_du_update_layout(dev_priv, 1, &def_rect);
 		return 0;
+	} else if (arg->num_outputs > VMWGFX_NUM_DISPLAY_UNITS) {
+		return -E2BIG;
 	}
 
 	rects_size = arg->num_outputs * sizeof(struct drm_vmw_rect);
@@ -2516,7 +2529,7 @@
 	if (file_priv)
 		vmw_execbuf_copy_fence_user(dev_priv, vmw_fpriv(file_priv),
 					    ret, user_fence_rep, fence,
-					    handle, -1, NULL);
+					    handle, -1);
 	if (out_fence)
 		*out_fence = fence;
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_kms.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_kms.h
@@ -198,9 +198,6 @@
 	s32 unit_y2;
 };
 
-#define VMWGFX_NUM_DISPLAY_UNITS 8
-
-
 #define vmw_framebuffer_to_vfb(x) \
 	container_of(x, struct vmw_framebuffer, base)
 #define vmw_framebuffer_to_vfbs(x) \
@@ -246,11 +243,10 @@
 
 
 static const uint32_t __maybe_unused vmw_primary_plane_formats[] = {
-	DRM_FORMAT_XRGB1555,
-	DRM_FORMAT_RGB565,
-	DRM_FORMAT_RGB888,
 	DRM_FORMAT_XRGB8888,
 	DRM_FORMAT_ARGB8888,
+	DRM_FORMAT_RGB565,
+	DRM_FORMAT_XRGB1555,
 };
 
 static const uint32_t __maybe_unused vmw_cursor_plane_formats[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_mob.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_mob.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0 OR MIT
 /**************************************************************************
  *
- * Copyright 2012-2015 VMware, Inc., Palo Alto, CA., USA
+ * Copyright 2012-2021 VMware, Inc., Palo Alto, CA., USA
  *
  * Permission is hereby granted, free of charge, to any person obtaining a
  * copy of this software and associated documentation files (the
@@ -29,12 +29,6 @@
 
 #include "vmwgfx_drv.h"
 
-/*
- * If we set up the screen target otable, screen objects stop working.
- */
-
-#define VMW_OTABLE_SETUP_SUB ((VMWGFX_ENABLE_SCREEN_TARGET_OTABLE ? 0 : 1))
-
 #ifdef CONFIG_64BIT
 #define VMW_PPN_SIZE 8
 #define VMW_MOBFMT_PTDEPTH_0 SVGA3D_MOBFMT_PT64_0
@@ -75,7 +69,7 @@
 	{VMWGFX_NUM_GB_CONTEXT * sizeof(SVGAOTableContextEntry), NULL, true},
 	{VMWGFX_NUM_GB_SHADER * sizeof(SVGAOTableShaderEntry), NULL, true},
 	{VMWGFX_NUM_GB_SCREEN_TARGET * sizeof(SVGAOTableScreenTargetEntry),
-	 NULL, VMWGFX_ENABLE_SCREEN_TARGET_OTABLE}
+	 NULL, true}
 };
 
 static const struct vmw_otable dx_tables[] = {
@@ -84,7 +78,7 @@
 	{VMWGFX_NUM_GB_CONTEXT * sizeof(SVGAOTableContextEntry), NULL, true},
 	{VMWGFX_NUM_GB_SHADER * sizeof(SVGAOTableShaderEntry), NULL, true},
 	{VMWGFX_NUM_GB_SCREEN_TARGET * sizeof(SVGAOTableScreenTargetEntry),
-	 NULL, VMWGFX_ENABLE_SCREEN_TARGET_OTABLE},
+	 NULL, true},
 	{VMWGFX_NUM_DXCONTEXT * sizeof(SVGAOTableDXContextEntry), NULL, true},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_msg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_msg.c
@@ -1076,6 +1076,7 @@
 
 	if (desc_len < 0) {
 		atomic_set(&dev_priv->mksstat_user_pids[slot], 0);
+		__free_page(page);
 		return -EFAULT;
 	}
 
@@ -1084,21 +1085,21 @@
 	reset_ppn_array(pdesc->strsPPNs, ARRAY_SIZE(pdesc->strsPPNs));
 
 	/* Pin mksGuestStat user pages and store those in the instance descriptor */
-	nr_pinned_stat = pin_user_pages(arg->stat, num_pages_stat, FOLL_LONGTERM, pages_stat, NULL);
+	nr_pinned_stat = pin_user_pages_fast(arg->stat, num_pages_stat, FOLL_LONGTERM, pages_stat);
 	if (num_pages_stat != nr_pinned_stat)
 		goto err_pin_stat;
 
 	for (i = 0; i < num_pages_stat; ++i)
 		pdesc->statPPNs[i] = page_to_pfn(pages_stat[i]);
 
-	nr_pinned_info = pin_user_pages(arg->info, num_pages_info, FOLL_LONGTERM, pages_info, NULL);
+	nr_pinned_info = pin_user_pages_fast(arg->info, num_pages_info, FOLL_LONGTERM, pages_info);
 	if (num_pages_info != nr_pinned_info)
 		goto err_pin_info;
 
 	for (i = 0; i < num_pages_info; ++i)
 		pdesc->infoPPNs[i] = page_to_pfn(pages_info[i]);
 
-	nr_pinned_strs = pin_user_pages(arg->strs, num_pages_strs, FOLL_LONGTERM, pages_strs, NULL);
+	nr_pinned_strs = pin_user_pages_fast(arg->strs, num_pages_strs, FOLL_LONGTERM, pages_strs);
 	if (num_pages_strs != nr_pinned_strs)
 		goto err_pin_strs;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_overlay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_overlay.c
@@ -98,7 +98,7 @@
 {
 	struct vmw_escape_video_flush *flush;
 	size_t fifo_size;
-	bool have_so = (dev_priv->active_display_unit == vmw_du_screen_object);
+	bool have_so = (dev_priv->active_display_unit != vmw_du_legacy);
 	int i, num_items;
 	SVGAGuestPtr ptr;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_page_dirty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_page_dirty.c
@@ -477,7 +477,7 @@
 	else
 		prot = vm_get_page_prot(vma->vm_flags);
 
-	ret = ttm_bo_vm_fault_reserved(vmf, prot, num_prefault, 1);
+	ret = ttm_bo_vm_fault_reserved(vmf, prot, num_prefault);
 	if (ret == VM_FAULT_RETRY && !(vmf->flags & FAULT_FLAG_RETRY_NOWAIT))
 		return ret;
 
@@ -486,73 +486,3 @@
 
 	return ret;
 }
-
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-vm_fault_t vmw_bo_vm_huge_fault(struct vm_fault *vmf,
-				enum page_entry_size pe_size)
-{
-	struct vm_area_struct *vma = vmf->vma;
-	struct ttm_buffer_object *bo = (struct ttm_buffer_object *)
-	    vma->vm_private_data;
-	struct vmw_buffer_object *vbo =
-		container_of(bo, struct vmw_buffer_object, base);
-	pgprot_t prot;
-	vm_fault_t ret;
-	pgoff_t fault_page_size;
-	bool write = vmf->flags & FAULT_FLAG_WRITE;
-
-	switch (pe_size) {
-	case PE_SIZE_PMD:
-		fault_page_size = HPAGE_PMD_SIZE >> PAGE_SHIFT;
-		break;
-#ifdef CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD
-	case PE_SIZE_PUD:
-		fault_page_size = HPAGE_PUD_SIZE >> PAGE_SHIFT;
-		break;
-#endif
-	default:
-		WARN_ON_ONCE(1);
-		return VM_FAULT_FALLBACK;
-	}
-
-	/* Always do write dirty-tracking and COW on PTE level. */
-	if (write && (READ_ONCE(vbo->dirty) || is_cow_mapping(vma->vm_flags)))
-		return VM_FAULT_FALLBACK;
-
-	ret = ttm_bo_vm_reserve(bo, vmf);
-	if (ret)
-		return ret;
-
-	if (vbo->dirty) {
-		pgoff_t allowed_prefault;
-		unsigned long page_offset;
-
-		page_offset = vmf->pgoff -
-			drm_vma_node_start(&bo->base.vma_node);
-		if (page_offset >= bo->resource->num_pages ||
-		    vmw_resources_clean(vbo, page_offset,
-					page_offset + PAGE_SIZE,
-					&allowed_prefault)) {
-			ret = VM_FAULT_SIGBUS;
-			goto out_unlock;
-		}
-
-		/*
-		 * Write protect, so we get a new fault on write, and can
-		 * split.
-		 */
-		prot = vm_get_page_prot(vma->vm_flags & ~VM_SHARED);
-	} else {
-		prot = vm_get_page_prot(vma->vm_flags);
-	}
-
-	ret = ttm_bo_vm_fault_reserved(vmf, prot, 1, fault_page_size);
-	if (ret == VM_FAULT_RETRY && !(vmf->flags & FAULT_FLAG_RETRY_NOWAIT))
-		return ret;
-
-out_unlock:
-	dma_resv_unlock(bo->base.resv);
-
-	return ret;
-}
-#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_resource.c
@@ -862,22 +862,21 @@
 	struct ttm_device *bdev = bo->bdev;
 	struct vmw_private *dev_priv;
 
-
 	dev_priv = container_of(bdev, struct vmw_private, bdev);
 
 	mutex_lock(&dev_priv->binding_mutex);
 
-	dx_query_mob = container_of(bo, struct vmw_buffer_object, base);
-	if (!dx_query_mob || !dx_query_mob->dx_query_ctx) {
-		mutex_unlock(&dev_priv->binding_mutex);
-		return;
-	}
-
 	/* If BO is being moved from MOB to system memory */
 	if (new_mem->mem_type == TTM_PL_SYSTEM &&
 	    old_mem->mem_type == VMW_PL_MOB) {
 		struct vmw_fence_obj *fence;
 
+		dx_query_mob = container_of(bo, struct vmw_buffer_object, base);
+		if (!dx_query_mob || !dx_query_mob->dx_query_ctx) {
+			mutex_unlock(&dev_priv->binding_mutex);
+			return;
+		}
+
 		(void) vmw_query_readback_all(dx_query_mob);
 		mutex_unlock(&dev_priv->binding_mutex);
 
@@ -891,7 +890,6 @@
 		(void) ttm_bo_wait(bo, false, false);
 	} else
 		mutex_unlock(&dev_priv->binding_mutex);
-
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_scrn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_scrn.c
@@ -953,6 +953,10 @@
 	struct drm_device *dev = &dev_priv->drm;
 	int i, ret;
 
+	/* Screen objects won't work if GMR's aren't available */
+	if (!dev_priv->has_gmr)
+		return -ENOSYS;
+
 	if (!(dev_priv->capabilities & SVGA_CAP_SCREEN_OBJECT_2)) {
 		return -ENOSYS;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_stdu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_stdu.c
@@ -1872,8 +1872,8 @@
 	int i, ret;
 
 
-	/* Do nothing if Screen Target support is turned off */
-	if (!VMWGFX_ENABLE_SCREEN_TARGET_OTABLE || !dev_priv->has_mob)
+	/* Do nothing if there's no support for MOBs */
+	if (!dev_priv->has_mob)
 		return -ENOSYS;
 
 	if (!(dev_priv->capabilities & SVGA_CAP_GBOBJECTS))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_surface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_surface.c
@@ -807,9 +807,9 @@
 	metadata->num_sizes = num_sizes;
 	user_srf->size = size;
 	metadata->sizes =
-		memdup_user((struct drm_vmw_size __user *)(unsigned long)
+		memdup_array_user((struct drm_vmw_size __user *)(unsigned long)
 			    req->size_addr,
-			    sizeof(*metadata->sizes) * metadata->num_sizes);
+			    metadata->num_sizes, sizeof(*metadata->sizes));
 	if (IS_ERR(metadata->sizes)) {
 		ret = PTR_ERR(metadata->sizes);
 		goto out_no_sizes;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_system_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_system_manager.c
@@ -0,0 +1,91 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright 2021 VMware, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use, copy,
+ * modify, merge, publish, distribute, sublicense, and/or sell copies
+ * of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ *
+ */
+
+#include "vmwgfx_drv.h"
+
+#include <drm/ttm/ttm_bo_driver.h>
+#include <drm/ttm/ttm_device.h>
+#include <drm/ttm/ttm_placement.h>
+#include <drm/ttm/ttm_resource.h>
+#include <linux/slab.h>
+
+
+static int vmw_sys_man_alloc(struct ttm_resource_manager *man,
+			     struct ttm_buffer_object *bo,
+			     const struct ttm_place *place,
+			     struct ttm_resource **res)
+{
+	*res = kzalloc(sizeof(**res), GFP_KERNEL);
+	if (!*res)
+		return -ENOMEM;
+
+	ttm_resource_init(bo, place, *res);
+	return 0;
+}
+
+static void vmw_sys_man_free(struct ttm_resource_manager *man,
+			     struct ttm_resource *res)
+{
+	ttm_resource_fini(man, res);
+	kfree(res);
+}
+
+static const struct ttm_resource_manager_func vmw_sys_manager_func = {
+	.alloc = vmw_sys_man_alloc,
+	.free = vmw_sys_man_free,
+};
+
+int vmw_sys_man_init(struct vmw_private *dev_priv)
+{
+	struct ttm_device *bdev = &dev_priv->bdev;
+	struct ttm_resource_manager *man =
+			kzalloc(sizeof(*man), GFP_KERNEL);
+
+	if (!man)
+		return -ENOMEM;
+
+	man->use_tt = true;
+	man->func = &vmw_sys_manager_func;
+
+	ttm_resource_manager_init(man, 0);
+	ttm_set_driver_manager(bdev, VMW_PL_SYSTEM, man);
+	ttm_resource_manager_set_used(man, true);
+	return 0;
+}
+
+void vmw_sys_man_fini(struct vmw_private *dev_priv)
+{
+	struct ttm_resource_manager *man = ttm_manager_type(&dev_priv->bdev,
+							    VMW_PL_SYSTEM);
+
+	ttm_resource_manager_evict_all(&dev_priv->bdev, man);
+
+	ttm_resource_manager_set_used(man, false);
+	ttm_resource_manager_cleanup(man);
+
+	ttm_set_driver_manager(&dev_priv->bdev, VMW_PL_SYSTEM, NULL);
+	kfree(man);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_ttm_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_ttm_buffer.c
@@ -92,6 +92,13 @@
 	}
 };
 
+static const struct ttm_place vmw_sys_placement_flags = {
+	.fpfn = 0,
+	.lpfn = 0,
+	.mem_type = VMW_PL_SYSTEM,
+	.flags = 0
+};
+
 struct ttm_placement vmw_vram_gmr_placement = {
 	.num_placement = 2,
 	.placement = vram_gmr_placement_flags,
@@ -113,28 +120,11 @@
 	.busy_placement = &sys_placement_flags
 };
 
-static const struct ttm_place evictable_placement_flags[] = {
-	{
-		.fpfn = 0,
-		.lpfn = 0,
-		.mem_type = TTM_PL_SYSTEM,
-		.flags = 0
-	}, {
-		.fpfn = 0,
-		.lpfn = 0,
-		.mem_type = TTM_PL_VRAM,
-		.flags = 0
-	}, {
-		.fpfn = 0,
-		.lpfn = 0,
-		.mem_type = VMW_PL_GMR,
-		.flags = 0
-	}, {
-		.fpfn = 0,
-		.lpfn = 0,
-		.mem_type = VMW_PL_MOB,
-		.flags = 0
-	}
+struct ttm_placement vmw_pt_sys_placement = {
+	.num_placement = 1,
+	.placement = &vmw_sys_placement_flags,
+	.num_busy_placement = 1,
+	.busy_placement = &vmw_sys_placement_flags
 };
 
 static const struct ttm_place nonfixed_placement_flags[] = {
@@ -156,13 +146,6 @@
 	}
 };
 
-struct ttm_placement vmw_evictable_placement = {
-	.num_placement = 4,
-	.placement = evictable_placement_flags,
-	.num_busy_placement = 1,
-	.busy_placement = &sys_placement_flags
-};
-
 struct ttm_placement vmw_srf_placement = {
 	.num_placement = 1,
 	.num_busy_placement = 2,
@@ -484,6 +467,9 @@
 				    &vmw_be->vsgt, ttm->num_pages,
 				    vmw_be->gmr_id);
 		break;
+	case VMW_PL_SYSTEM:
+		/* Nothing to be done for a system bind */
+		break;
 	default:
 		BUG();
 	}
@@ -507,6 +493,8 @@
 	case VMW_PL_MOB:
 		vmw_mob_unbind(vmw_be->dev_priv, vmw_be->mob);
 		break;
+	case VMW_PL_SYSTEM:
+		break;
 	default:
 		BUG();
 	}
@@ -628,6 +616,7 @@
 
 	switch (mem->mem_type) {
 	case TTM_PL_SYSTEM:
+	case VMW_PL_SYSTEM:
 	case VMW_PL_GMR:
 	case VMW_PL_MOB:
 		return 0;
@@ -674,6 +663,11 @@
 	(void) ttm_bo_wait(bo, false, false);
 }
 
+static bool vmw_memtype_is_system(uint32_t mem_type)
+{
+	return mem_type == TTM_PL_SYSTEM || mem_type == VMW_PL_SYSTEM;
+}
+
 static int vmw_move(struct ttm_buffer_object *bo,
 		    bool evict,
 		    struct ttm_operation_ctx *ctx,
@@ -684,7 +678,7 @@
 	struct ttm_resource_manager *new_man = ttm_manager_type(bo->bdev, new_mem->mem_type);
 	int ret;
 
-	if (new_man->use_tt && new_mem->mem_type != TTM_PL_SYSTEM) {
+	if (new_man->use_tt && !vmw_memtype_is_system(new_mem->mem_type)) {
 		ret = vmw_ttm_bind(bo->bdev, bo->ttm, new_mem);
 		if (ret)
 			return ret;
@@ -693,7 +687,7 @@
 	vmw_move_notify(bo, bo->resource, new_mem);
 
 	if (old_man->use_tt && new_man->use_tt) {
-		if (bo->resource->mem_type == TTM_PL_SYSTEM) {
+		if (vmw_memtype_is_system(bo->resource->mem_type)) {
 			ttm_bo_move_null(bo, new_mem);
 			return 0;
 		}
@@ -740,7 +734,7 @@
 	int ret;
 
 	ret = vmw_bo_create_kernel(dev_priv, bo_size,
-				   &vmw_sys_placement,
+				   &vmw_pt_sys_placement,
 				   &bo);
 	if (unlikely(ret != 0))
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/vmwgfx/vmwgfx_ttm_glue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/vmwgfx/vmwgfx_ttm_glue.c
@@ -61,9 +61,6 @@
 		.fault = vmw_bo_vm_fault,
 		.open = ttm_bo_vm_open,
 		.close = ttm_bo_vm_close,
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-		.huge_fault = vmw_bo_vm_huge_fault,
-#endif
 	};
 	struct drm_file *file_priv = filp->private_data;
 	struct vmw_private *dev_priv = vmw_priv(file_priv->minor->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/Kconfig
@@ -3,14 +3,125 @@
 	depends on ARCH_ZYNQMP || COMPILE_TEST
 	depends on COMMON_CLK && DRM && OF
 	depends on DMADEVICES
-	depends on PHY_XILINX_ZYNQMP
-	depends on XILINX_ZYNQMP_DPDMA
-	select DMA_ENGINE
-	select DRM_GEM_CMA_HELPER
-	select DRM_KMS_CMA_HELPER
-	select DRM_KMS_HELPER
-	select GENERIC_PHY
+	depends on DRM_XLNX
+	select VIDEOMODE_HELPERS
+	select XILINX_DMA_ENGINES
+	select PHY_XILINX_ZYNQMP
+	select XILINX_ZYNQMP_DPDMA
+	select MFD_SYSCON
 	help
 	  This is a DRM/KMS driver for ZynqMP DisplayPort controller. Choose
 	  this option if you have a Xilinx ZynqMP SoC with DisplayPort
 	  subsystem.
+
+config DRM_XLNX
+	tristate "Xilinx DRM KMS Driver"
+	depends on DRM && OF
+	select DRM_KMS_HELPER
+	select DRM_KMS_CMA_HELPER
+	select DRM_GEM_CMA_HELPER
+	select SND_PCM_ELD
+	help
+	  Xilinx DRM KMS driver. Choose this option if you have
+	  a Xilinx SoCs with hardened display pipeline or soft
+	  display pipeline using Xilinx IPs in FPGA. This module
+	  provides the kernel mode setting functionalities
+	  for Xilinx display drivers.
+
+config DRM_XLNX_BRIDGE
+	tristate "Xilinx DRM KMS bridge"
+	depends on DRM_XLNX
+	help
+	  Xilinx DRM KMS bridge. This module provides some interfaces
+	  to enable inter-module communication. Choose this option
+	  from the provider driver when the Xilinx bridge interface is
+	  needed.
+
+config DRM_XLNX_BRIDGE_DEBUG_FS
+	bool "Xilinx DRM KMS bridge debugfs"
+	depends on DEBUG_FS && DRM_XLNX_BRIDGE
+	help
+	  Enable the debugfs code for Xilinx bridge. The debugfs code
+	  enables debugging or testing related features. It exposes some
+	  low level controls to the user space to help testing automation,
+	  as well as can enable additional diagnostic or statistical
+	  information.
+
+config DRM_XLNX_DPTX
+	tristate "Xilinx DRM DisplayPort Subsystem Driver"
+	depends on DRM_XLNX
+	help
+	  DRM driver for Xilinx DisplayPort Tx Subsystem for FPGA. Choose
+	  this option if you have a FPGA display pipeline that includes
+	  the Xilinx DisplayPort Tx Subsystem IP. The driver provides
+	  the kernel mode setting functionalities for the IP.
+
+config DRM_XLNX_DSI
+	tristate "Xilinx DRM DSI Subsystem Driver"
+	depends on DRM_XLNX
+	select DRM_MIPI_DSI
+	select DRM_PANEL
+	select BACKLIGHT_LCD_SUPPORT
+	select BACKLIGHT_CLASS_DEVICE
+	help
+	  DRM driver for Xilinx MIPI-DSI.
+
+config DRM_XLNX_HDMITX
+	tristate "Xilinx DRM HDMI Subsystem Driver"
+	depends on DRM_XLNX
+	help
+	  DRM driver for Xilinx HDMI Tx Subsystem for FPGA. Choose
+	  this option if you have a FPGA display pipeline that includes
+	  the Xilinx HDMI Tx Subsystem IP. The driver provides
+	  the kernel mode setting functionalities for the IP.
+
+config DRM_XLNX_MIXER
+	tristate "Xilinx DRM Mixer Driver"
+	depends on DRM_XLNX
+	select VIDEOMODE_HELPERS
+	help
+	  DRM driver for Xilinx Mixer driver.
+
+config DRM_XLNX_PL_DISP
+	tristate "Xilinx DRM PL display driver"
+	depends on DRM_XLNX && XILINX_FRMBUF
+	select VIDEOMODE_HELPERS
+	help
+	  DRM driver for Xilinx PL display driver, provides drm
+	  crtc and plane object to display pipeline. You need to
+	  choose this option if your display pipeline needs one
+	  crtc and plane object with single DMA connected.
+
+config DRM_XLNX_SDI
+	tristate "Xilinx DRM SDI Subsystem Driver"
+	depends on DRM_XLNX
+	help
+	  DRM driver for Xilinx SDI Tx Subsystem.
+
+config DRM_XLNX_BRIDGE_CSC
+	tristate "Xilinx DRM CSC Driver"
+	depends on DRM_XLNX_BRIDGE
+	help
+	  DRM brige driver for color space converter of VPSS. Choose
+	  this option if color space converter is connected to an encoder.
+	  The driver provides set/get resolution and color format
+	  functionality through bridge layer.
+
+config DRM_XLNX_BRIDGE_SCALER
+	tristate "Xilinx DRM Scaler Driver"
+	depends on DRM_XLNX_BRIDGE
+	help
+	  DRM brige driver for scaler of VPSS. Choose this option
+	  if scaler is connected to an encoder. The driver provides
+	  upscaling, down scaling and no scaling functionality through
+	  bridge layer.
+
+config DRM_XLNX_BRIDGE_VTC
+	tristate "Xilinx DRM VTC Driver"
+	depends on DRM_XLNX_BRIDGE
+	help
+	  DRM brige driver for Xilinx Video Timing Controller. Choose
+	  this option to make VTC a part of the CRTC in display pipeline.
+	  Currently the support is added to the Xilinx Video Mixer and
+	  Xilinx PL display CRTC drivers. This driver provides ability
+	  to generate timings through the bridge layer.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/Makefile
@@ -1,2 +1,15 @@
 zynqmp-dpsub-y := zynqmp_disp.o zynqmp_dpsub.o zynqmp_dp.o
 obj-$(CONFIG_DRM_ZYNQMP_DPSUB) += zynqmp-dpsub.o
+xlnx_drm-objs += xlnx_crtc.o xlnx_drv.o xlnx_fb.o xlnx_gem.o
+xlnx_drm-$(CONFIG_DRM_XLNX_BRIDGE) += xlnx_bridge.o
+obj-$(CONFIG_DRM_XLNX) += xlnx_drm.o
+obj-$(CONFIG_DRM_XLNX_BRIDGE_CSC) += xlnx_csc.o
+obj-$(CONFIG_DRM_XLNX_BRIDGE_SCALER) += xlnx_scaler.o
+obj-$(CONFIG_DRM_XLNX_BRIDGE_VTC) += xlnx_vtc.o
+obj-$(CONFIG_DRM_XLNX_DPTX) += xlnx_dptx.o
+obj-$(CONFIG_DRM_XLNX_DSI) += xlnx_dsi.o
+obj-$(CONFIG_DRM_XLNX_HDMITX) += xlnx_hdmi.o
+obj-$(CONFIG_DRM_XLNX_MIXER) += xlnx_mixer.o
+obj-$(CONFIG_DRM_XLNX_PL_DISP) += xlnx_pl_disp.o
+xlnx-sdi-objs += xlnx_sdi.o xlnx_sdi_timing.o
+obj-$(CONFIG_DRM_XLNX_SDI) += xlnx-sdi.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_bridge.c
@@ -0,0 +1,575 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM bridge driver
+ *
+ *  Copyright (C) 2017 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/list.h>
+
+#include "xlnx_bridge.h"
+#include "xlnx_drv.h"
+
+/*
+ * Overview
+ * --------
+ *
+ * Similar to drm bridge, but this can be used by any DRM driver. There
+ * is no limitation to be used by non DRM drivers as well. No complex topology
+ * is modeled, thus it's assumed that the Xilinx bridge device is directly
+ * attached to client. The client should call Xilinx bridge functions explicitly
+ * where it's needed, as opposed to drm bridge functions which are called
+ * implicitly by DRM core.
+ * One Xlnx bridge can be owned by one driver at a time.
+ */
+
+/**
+ * struct xlnx_bridge_helper - Xilinx bridge helper
+ * @xlnx_bridges: list of Xilinx bridges
+ * @lock: lock to protect @xlnx_crtcs
+ * @refcnt: reference count
+ * @error: flag if in error state
+ */
+struct xlnx_bridge_helper {
+	struct list_head xlnx_bridges;
+	struct mutex lock; /* lock for @xlnx_bridges */
+	unsigned int refcnt;
+	bool error;
+};
+
+static struct xlnx_bridge_helper helper;
+
+struct videomode;
+/*
+ * Client functions
+ */
+
+/**
+ * xlnx_bridge_enable - Enable the bridge
+ * @bridge: bridge to enable
+ *
+ * Enable bridge.
+ *
+ * Return: 0 on success. -ENOENT if no callback, -EFAULT in error state,
+ * or return code from callback.
+ */
+int xlnx_bridge_enable(struct xlnx_bridge *bridge)
+{
+	if (!bridge)
+		return 0;
+
+	if (helper.error)
+		return -EFAULT;
+
+	if (bridge->enable)
+		return bridge->enable(bridge);
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(xlnx_bridge_enable);
+
+/**
+ * xlnx_bridge_disable - Disable the bridge
+ * @bridge: bridge to disable
+ *
+ * Disable bridge.
+ */
+void xlnx_bridge_disable(struct xlnx_bridge *bridge)
+{
+	if (!bridge)
+		return;
+
+	if (helper.error)
+		return;
+
+	if (bridge->disable)
+		bridge->disable(bridge);
+}
+EXPORT_SYMBOL(xlnx_bridge_disable);
+
+/**
+ * xlnx_bridge_set_input - Set the input of @bridge
+ * @bridge: bridge to set
+ * @width: width
+ * @height: height
+ * @bus_fmt: bus format (ex, MEDIA_BUS_FMT_*);
+ *
+ * Set the bridge input with height / width / format.
+ *
+ * Return: 0 on success. -ENOENT if no callback, -EFAULT if in error state,
+ * or return code from callback.
+ */
+int xlnx_bridge_set_input(struct xlnx_bridge *bridge,
+			  u32 width, u32 height, u32 bus_fmt)
+{
+	if (!bridge)
+		return 0;
+
+	if (helper.error)
+		return -EFAULT;
+
+	if (bridge->set_input)
+		return bridge->set_input(bridge, width, height, bus_fmt);
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(xlnx_bridge_set_input);
+
+/**
+ * xlnx_bridge_get_input_fmts - Get the supported input formats
+ * @bridge: bridge to set
+ * @fmts: pointer to formats
+ * @count: pointer to format count
+ *
+ * Get the list of supported input bus formats.
+ *
+ * Return: 0 on success. -ENOENT if no callback, -EFAULT if in error state,
+ * or return code from callback.
+ */
+int xlnx_bridge_get_input_fmts(struct xlnx_bridge *bridge,
+			       const u32 **fmts, u32 *count)
+{
+	if (!bridge)
+		return 0;
+
+	if (helper.error)
+		return -EFAULT;
+
+	if (bridge->get_input_fmts)
+		return bridge->get_input_fmts(bridge, fmts, count);
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(xlnx_bridge_get_input_fmts);
+
+/**
+ * xlnx_bridge_set_output - Set the output of @bridge
+ * @bridge: bridge to set
+ * @width: width
+ * @height: height
+ * @bus_fmt: bus format (ex, MEDIA_BUS_FMT_*);
+ *
+ * Set the bridge output with height / width / format.
+ *
+ * Return: 0 on success. -ENOENT if no callback, -EFAULT if in error state,
+ * or return code from callback.
+ */
+int xlnx_bridge_set_output(struct xlnx_bridge *bridge,
+			   u32 width, u32 height, u32 bus_fmt)
+{
+	if (!bridge)
+		return 0;
+
+	if (helper.error)
+		return -EFAULT;
+
+	if (bridge->set_output)
+		return bridge->set_output(bridge, width, height, bus_fmt);
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(xlnx_bridge_set_output);
+
+/**
+ * xlnx_bridge_get_output_fmts - Get the supported output formats
+ * @bridge: bridge to set
+ * @fmts: pointer to formats
+ * @count: pointer to format count
+ *
+ * Get the list of supported output bus formats.
+ *
+ * Return: 0 on success. -ENOENT if no callback, -EFAULT if in error state,
+ * or return code from callback.
+ */
+int xlnx_bridge_get_output_fmts(struct xlnx_bridge *bridge,
+				const u32 **fmts, u32 *count)
+{
+	if (!bridge)
+		return 0;
+
+	if (helper.error)
+		return -EFAULT;
+
+	if (bridge->get_output_fmts)
+		return bridge->get_output_fmts(bridge, fmts, count);
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(xlnx_bridge_get_output_fmts);
+
+/**
+ * xlnx_bridge_set_timing - Set the video timing
+ * @bridge: bridge to set
+ * @vm: Videomode
+ *
+ * Set the video mode so that timing can be generated using this
+ * by the video timing controller.
+ *
+ * Return: 0 on success. -ENOENT if no callback, -EFAULT if in error state,
+ * or return code from callback.
+ */
+int xlnx_bridge_set_timing(struct xlnx_bridge *bridge, struct videomode *vm)
+{
+	if (!bridge)
+		return 0;
+
+	if (helper.error)
+		return -EFAULT;
+
+	if (bridge->set_timing) {
+		bridge->set_timing(bridge, vm);
+		return 0;
+	}
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(xlnx_bridge_set_timing);
+
+/**
+ * of_xlnx_bridge_get - Get the corresponding Xlnx bridge instance
+ * @bridge_np: The device node of the bridge device
+ *
+ * The function walks through the Xlnx bridge list of @drm, and return
+ * if any registered bridge matches the device node. The returned
+ * bridge will not be accesible by others.
+ *
+ * Return: the matching Xlnx bridge instance, or NULL
+ */
+struct xlnx_bridge *of_xlnx_bridge_get(struct device_node *bridge_np)
+{
+	struct xlnx_bridge *found = NULL;
+	struct xlnx_bridge *bridge;
+
+	if (helper.error)
+		return NULL;
+
+	mutex_lock(&helper.lock);
+	list_for_each_entry(bridge, &helper.xlnx_bridges, list) {
+		if (bridge->of_node == bridge_np && !bridge->owned) {
+			found = bridge;
+			bridge->owned = true;
+			break;
+		}
+	}
+	mutex_unlock(&helper.lock);
+
+	return found;
+}
+EXPORT_SYMBOL_GPL(of_xlnx_bridge_get);
+
+/**
+ * of_xlnx_bridge_put - Put the Xlnx bridge instance
+ * @bridge: Xlnx bridge instance to release
+ *
+ * Return the @bridge. After this, the bridge will be available for
+ * other drivers to use.
+ */
+void of_xlnx_bridge_put(struct xlnx_bridge *bridge)
+{
+	if (WARN_ON(helper.error))
+		return;
+
+	mutex_lock(&helper.lock);
+	WARN_ON(!bridge->owned);
+	bridge->owned = false;
+	mutex_unlock(&helper.lock);
+}
+EXPORT_SYMBOL_GPL(of_xlnx_bridge_put);
+
+#ifdef CONFIG_DRM_XLNX_BRIDGE_DEBUG_FS
+
+#include <linux/debugfs.h>
+
+struct xlnx_bridge_debugfs_dir {
+	struct dentry *dir;
+	int ref_cnt;
+};
+
+static struct xlnx_bridge_debugfs_dir *dir;
+
+struct xlnx_bridge_debugfs_file {
+	struct dentry *file;
+	const char *status;
+};
+
+#define XLNX_BRIDGE_DEBUGFS_MAX_BYTES	16
+
+static ssize_t xlnx_bridge_debugfs_read(struct file *f, char __user *buf,
+					size_t size, loff_t *pos)
+{
+	struct xlnx_bridge *bridge = f->f_inode->i_private;
+	int ret, count = 0;
+
+	if (size <= 0)
+		return -EINVAL;
+
+	if (*pos != 0)
+		return 0;
+
+	if (bridge->debugfs_file->status) {
+		count = min(size, strlen(bridge->debugfs_file->status));
+		ret = copy_to_user(buf, bridge->debugfs_file->status, count);
+		if (ret)
+			count = -EFAULT;
+	}
+
+	return count;
+}
+
+static ssize_t xlnx_bridge_debugfs_write(struct file *f, const char __user *buf,
+					 size_t size, loff_t *pos)
+{
+	struct xlnx_bridge *bridge = f->f_inode->i_private;
+
+	if (*pos != 0 || size <= 0)
+		return -EINVAL;
+
+	if (!strncmp(buf, "enable", 5)) {
+		xlnx_bridge_enable(bridge);
+	} else if (!strncmp(buf, "disable", 6)) {
+		xlnx_bridge_disable(bridge);
+	} else if (!strncmp(buf, "set_input", 3)) {
+		char *cmd, **tmp;
+		char *w, *h, *bus_fmt;
+		u32 width = 0, height = 0, fmt = 0;
+		int ret;
+
+		cmd = kzalloc(size, GFP_KERNEL);
+		if (!cmd)
+			return -ENOMEM;
+
+		ret = strncpy_from_user(cmd, buf, size);
+		if (ret < 0) {
+			pr_err("%s %d failed to copy the command  %s\n",
+			       __func__, __LINE__, buf);
+			kfree(cmd);
+			return ret;
+		}
+
+		tmp = &cmd;
+		strsep(tmp, " ");
+		w = strsep(tmp, " ");
+		h = strsep(tmp, " ");
+		bus_fmt = strsep(tmp, " ");
+		if (w && h && bus_fmt) {
+			ret = kstrtouint(w, 0, &width);
+			ret |= kstrtouint(h, 0, &height);
+			ret |= kstrtouint(bus_fmt, 0, &fmt);
+		}
+
+		kfree(cmd);
+		if (ret) {
+			pr_err("%s %d invalid command: %s\n",
+			       __func__, __LINE__, buf);
+			return -EINVAL;
+		}
+		xlnx_bridge_set_input(bridge, width, height, fmt);
+	}
+
+	return size;
+}
+
+static const struct file_operations xlnx_bridge_debugfs_fops = {
+	.owner	= THIS_MODULE,
+	.read	= xlnx_bridge_debugfs_read,
+	.write	= xlnx_bridge_debugfs_write,
+};
+
+static int xlnx_bridge_debugfs_register(struct xlnx_bridge *bridge)
+{
+	struct xlnx_bridge_debugfs_file *file;
+	char file_name[32];
+
+	file = kzalloc(sizeof(*file), GFP_KERNEL);
+	if (!file)
+		return -ENOMEM;
+
+	if (bridge->extra_name)
+		snprintf(file_name, sizeof(file_name), "xlnx_bridge-%s%s",
+			 bridge->of_node->name, bridge->extra_name);
+	else
+		snprintf(file_name, sizeof(file_name), "xlnx_bridge-%s",
+			 bridge->of_node->name);
+	file->file = debugfs_create_file(file_name, 0444, dir->dir, bridge,
+					 &xlnx_bridge_debugfs_fops);
+	bridge->debugfs_file = file;
+
+	return 0;
+}
+
+static void xlnx_bridge_debugfs_unregister(struct xlnx_bridge *bridge)
+{
+	if (!bridge->debugfs_file) {
+		pr_err("bridge %s debugfs file is NULL\n", bridge->of_node->name);
+		return;
+	}
+	debugfs_remove(bridge->debugfs_file->file);
+	kfree(bridge->debugfs_file);
+}
+
+static int xlnx_bridge_debugfs_init(void)
+{
+	if (dir) {
+		dir->ref_cnt++;
+		return 0;
+	}
+
+	dir = kzalloc(sizeof(*dir), GFP_KERNEL);
+	if (!dir)
+		return -ENOMEM;
+
+	dir->dir = debugfs_create_dir("xlnx-bridge", NULL);
+	if (!dir->dir)
+		return -ENODEV;
+	dir->ref_cnt++;
+
+	return 0;
+}
+
+static void xlnx_bridge_debugfs_fini(void)
+{
+	if (--dir->ref_cnt)
+		return;
+
+	debugfs_remove_recursive(dir->dir);
+	dir = NULL;
+}
+
+#else
+
+static int xlnx_bridge_debugfs_register(struct xlnx_bridge *bridge)
+{
+	return 0;
+}
+
+static void xlnx_bridge_debugfs_unregister(struct xlnx_bridge *bridge)
+{
+}
+
+static int xlnx_bridge_debugfs_init(void)
+{
+	return 0;
+}
+
+static void xlnx_bridge_debugfs_fini(void)
+{
+}
+
+#endif
+
+/*
+ * Provider functions
+ */
+
+/**
+ * xlnx_bridge_register - Register the bridge instance
+ * @bridge: Xlnx bridge instance to register
+ *
+ * Register @bridge to be available for clients.
+ *
+ * Return: 0 on success. -EPROBE_DEFER if helper is not initialized, or
+ * -EFAULT if in error state.
+ */
+int xlnx_bridge_register(struct xlnx_bridge *bridge)
+{
+	if (!helper.refcnt)
+		return -EPROBE_DEFER;
+
+	if (helper.error)
+		return -EFAULT;
+
+	mutex_lock(&helper.lock);
+	WARN_ON(!bridge->of_node);
+	bridge->owned = false;
+	xlnx_bridge_debugfs_register(bridge);
+	list_add_tail(&bridge->list, &helper.xlnx_bridges);
+	mutex_unlock(&helper.lock);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xlnx_bridge_register);
+
+/**
+ * xlnx_bridge_unregister - Unregister the bridge instance
+ * @bridge: Xlnx bridge instance to unregister
+ *
+ * Unregister @bridge. The bridge shouldn't be owned by any client
+ * at this point.
+ */
+void xlnx_bridge_unregister(struct xlnx_bridge *bridge)
+{
+	if (helper.error)
+		return;
+
+	mutex_lock(&helper.lock);
+	pr_warn("unregister bridge %s which is owned by other component\n",
+		bridge->of_node->name);
+	xlnx_bridge_debugfs_unregister(bridge);
+	list_del(&bridge->list);
+	mutex_unlock(&helper.lock);
+}
+EXPORT_SYMBOL_GPL(xlnx_bridge_unregister);
+
+/*
+ * Internal functions: used by Xlnx DRM
+ */
+
+/**
+ * xlnx_bridge_helper_init - Initialize the bridge helper
+ * @void: No arg
+ *
+ * Initialize the bridge helper or increment the reference count
+ * if already initialized.
+ *
+ * Return: 0 on success, or -EFAULT if in error state.
+ */
+int xlnx_bridge_helper_init(void)
+{
+	if (helper.refcnt++ > 0) {
+		if (helper.error)
+			return -EFAULT;
+		return 0;
+	}
+
+	INIT_LIST_HEAD(&helper.xlnx_bridges);
+	mutex_init(&helper.lock);
+	helper.error = false;
+
+	if (xlnx_bridge_debugfs_init())
+		pr_err("failed to init xlnx bridge debugfs\n");
+
+	return 0;
+}
+
+/**
+ * xlnx_bridge_helper_fini - Release the bridge helper
+ *
+ * Clean up or decrement the reference of the bridge helper.
+ */
+void xlnx_bridge_helper_fini(void)
+{
+	if (--helper.refcnt > 0)
+		return;
+
+	xlnx_bridge_debugfs_fini();
+
+	if (WARN_ON(!list_empty(&helper.xlnx_bridges))) {
+		helper.error = true;
+		pr_err("any further xlnx bridge call will fail\n");
+	}
+
+	mutex_destroy(&helper.lock);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_bridge.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_bridge.h
@@ -0,0 +1,180 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx DRM bridge header
+ *
+ *  Copyright (C) 2017 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_BRIDGE_H_
+#define _XLNX_BRIDGE_H_
+
+struct videomode;
+
+struct xlnx_bridge_debugfs_file;
+
+/**
+ * struct xlnx_bridge - Xilinx bridge device
+ * @list: list node for Xilinx bridge device list
+ * @of_node: OF node for the bridge
+ * @owned: flag if the bridge is owned
+ * @enable: callback to enable the bridge
+ * @disable: callback to disable the bridge
+ * @set_input: callback to set the input
+ * @get_input_fmts: callback to get supported input formats.
+ * @set_output: callback to set the output
+ * @get_output_fmts: callback to get supported output formats.
+ * @set_timing: callback to set timing in connected video timing controller.
+ * @debugfs_file: for debugfs support
+ * @extra_name: name to distinguish the bridges which share the same of_node
+ */
+struct xlnx_bridge {
+	struct list_head list;
+	struct device_node *of_node;
+	bool owned;
+	int (*enable)(struct xlnx_bridge *bridge);
+	void (*disable)(struct xlnx_bridge *bridge);
+	int (*set_input)(struct xlnx_bridge *bridge,
+			 u32 width, u32 height, u32 bus_fmt);
+	int (*get_input_fmts)(struct xlnx_bridge *bridge,
+			      const u32 **fmts, u32 *count);
+	int (*set_output)(struct xlnx_bridge *bridge,
+			  u32 width, u32 height, u32 bus_fmt);
+	int (*get_output_fmts)(struct xlnx_bridge *bridge,
+			       const u32 **fmts, u32 *count);
+	int (*set_timing)(struct xlnx_bridge *bridge, struct videomode *vm);
+	struct xlnx_bridge_debugfs_file *debugfs_file;
+	char *extra_name;
+};
+
+#if IS_ENABLED(CONFIG_DRM_XLNX_BRIDGE)
+/*
+ * Helper functions: used within Xlnx DRM
+ */
+
+struct xlnx_bridge_helper;
+
+int xlnx_bridge_helper_init(void);
+void xlnx_bridge_helper_fini(void);
+
+/*
+ * Helper functions: used by client driver
+ */
+
+int xlnx_bridge_enable(struct xlnx_bridge *bridge);
+void xlnx_bridge_disable(struct xlnx_bridge *bridge);
+int xlnx_bridge_set_input(struct xlnx_bridge *bridge,
+			  u32 width, u32 height, u32 bus_fmt);
+int xlnx_bridge_get_input_fmts(struct xlnx_bridge *bridge,
+			       const u32 **fmts, u32 *count);
+int xlnx_bridge_set_output(struct xlnx_bridge *bridge,
+			   u32 width, u32 height, u32 bus_fmt);
+int xlnx_bridge_get_output_fmts(struct xlnx_bridge *bridge,
+				const u32 **fmts, u32 *count);
+int xlnx_bridge_set_timing(struct xlnx_bridge *bridge, struct videomode *vm);
+struct xlnx_bridge *of_xlnx_bridge_get(struct device_node *bridge_np);
+void of_xlnx_bridge_put(struct xlnx_bridge *bridge);
+
+/*
+ * Bridge registration: used by bridge driver
+ */
+
+int xlnx_bridge_register(struct xlnx_bridge *bridge);
+void xlnx_bridge_unregister(struct xlnx_bridge *bridge);
+
+#else /* CONFIG_DRM_XLNX_BRIDGE */
+
+struct xlnx_bridge_helper;
+
+static inline int xlnx_bridge_helper_init(void)
+{
+	return 0;
+}
+
+static inline void xlnx_bridge_helper_fini(void)
+{
+}
+
+static inline int xlnx_bridge_enable(struct xlnx_bridge *bridge)
+{
+	if (bridge)
+		return -ENODEV;
+	return 0;
+}
+
+static inline void xlnx_bridge_disable(struct xlnx_bridge *bridge)
+{
+}
+
+static inline int xlnx_bridge_set_input(struct xlnx_bridge *bridge,
+					u32 width, u32 height, u32 bus_fmt)
+{
+	if (bridge)
+		return -ENODEV;
+	return 0;
+}
+
+static inline int xlnx_bridge_get_input_fmts(struct xlnx_bridge *bridge,
+					     const u32 **fmts, u32 *count)
+{
+	if (bridge)
+		return -ENODEV;
+	return 0;
+}
+
+static inline int xlnx_bridge_set_output(struct xlnx_bridge *bridge,
+					 u32 width, u32 height, u32 bus_fmt)
+{
+	if (bridge)
+		return -ENODEV;
+	return 0;
+}
+
+static inline int xlnx_bridge_get_output_fmts(struct xlnx_bridge *bridge,
+					      const u32 **fmts, u32 *count)
+{
+	if (bridge)
+		return -ENODEV;
+	return 0;
+}
+
+static inline int xlnx_bridge_set_timing(struct xlnx_bridge *bridge,
+					 struct videomode *vm)
+{
+	if (bridge)
+		return -ENODEV;
+	return 0;
+}
+
+static inline struct xlnx_bridge *
+of_xlnx_bridge_get(struct device_node *bridge_np)
+{
+	return NULL;
+}
+
+static inline void of_xlnx_bridge_put(struct xlnx_bridge *bridge)
+{
+}
+
+static inline int xlnx_bridge_register(struct xlnx_bridge *bridge)
+{
+	return 0;
+}
+
+static inline void xlnx_bridge_unregister(struct xlnx_bridge *bridge)
+{
+}
+
+#endif /* CONFIG_DRM_XLNX_BRIDGE */
+
+#endif /* _XLNX_BRIDGE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_crtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_crtc.c
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM crtc driver
+ *
+ *  Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drm_drv.h>
+#include <drm/drm_crtc.h>
+
+#include <linux/list.h>
+#include <linux/dma-mapping.h>
+
+#include "xlnx_crtc.h"
+#include "xlnx_drv.h"
+
+/*
+ * Overview
+ * --------
+ *
+ * The Xilinx CRTC layer is to enable the custom interface to CRTC drivers.
+ * The interface is used by Xilinx DRM driver where it needs CRTC
+ * functionailty. CRTC drivers should attach the desired callbacks
+ * to struct xlnx_crtc and register the xlnx_crtc with correcsponding
+ * drm_device. It's highly recommended CRTC drivers register all callbacks
+ * even though many of them are optional.
+ * The CRTC helper simply walks through the registered CRTC device,
+ * and call the callbacks.
+ */
+
+/**
+ * struct xlnx_crtc_helper - Xilinx CRTC helper
+ * @xlnx_crtcs: list of Xilinx CRTC devices
+ * @lock: lock to protect @xlnx_crtcs
+ * @drm: back pointer to DRM core
+ */
+struct xlnx_crtc_helper {
+	struct list_head xlnx_crtcs;
+	struct mutex lock; /* lock for @xlnx_crtcs */
+	struct drm_device *drm;
+};
+
+#define XLNX_CRTC_MAX_HEIGHT_WIDTH	INT_MAX
+
+unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	unsigned int align = 1, tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_align) {
+			tmp = crtc->get_align(crtc);
+			align = ALIGN(align, tmp);
+		}
+	}
+
+	return align;
+}
+
+u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	u64 mask = DMA_BIT_MASK(sizeof(dma_addr_t) * 8), tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_dma_mask) {
+			tmp = crtc->get_dma_mask(crtc);
+			mask = min(mask, tmp);
+		}
+	}
+
+	return mask;
+}
+
+int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	int width = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_max_width) {
+			tmp = crtc->get_max_width(crtc);
+			width = min(width, tmp);
+		}
+	}
+
+	return width;
+}
+
+int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	int height = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_max_height) {
+			tmp = crtc->get_max_height(crtc);
+			height = min(height, tmp);
+		}
+	}
+
+	return height;
+}
+
+uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	u32 format = 0, tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_format) {
+			tmp = crtc->get_format(crtc);
+			if (format && format != tmp)
+				return 0;
+			format = tmp;
+		}
+	}
+
+	return format;
+}
+
+u32 xlnx_crtc_helper_get_cursor_width(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	u32 width = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_cursor_width) {
+			tmp = crtc->get_cursor_width(crtc);
+			width = min(width, tmp);
+		}
+	}
+
+	return width;
+}
+
+u32 xlnx_crtc_helper_get_cursor_height(struct xlnx_crtc_helper *helper)
+{
+	struct xlnx_crtc *crtc;
+	u32 height = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
+
+	list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+		if (crtc->get_cursor_height) {
+			tmp = crtc->get_cursor_height(crtc);
+			height = min(height, tmp);
+		}
+	}
+
+	return height;
+}
+struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm)
+{
+	struct xlnx_crtc_helper *helper;
+
+	helper = devm_kzalloc(drm->dev, sizeof(*helper), GFP_KERNEL);
+	if (!helper)
+		return ERR_PTR(-ENOMEM);
+
+	INIT_LIST_HEAD(&helper->xlnx_crtcs);
+	mutex_init(&helper->lock);
+	helper->drm = drm;
+
+	return helper;
+}
+
+void xlnx_crtc_helper_fini(struct drm_device *drm,
+			   struct xlnx_crtc_helper *helper)
+{
+	if (WARN_ON(helper->drm != drm))
+		return;
+
+	if (WARN_ON(!list_empty(&helper->xlnx_crtcs)))
+		return;
+
+	mutex_destroy(&helper->lock);
+	devm_kfree(drm->dev, helper);
+}
+
+void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc)
+{
+	struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
+
+	mutex_lock(&helper->lock);
+	list_add_tail(&crtc->list, &helper->xlnx_crtcs);
+	mutex_unlock(&helper->lock);
+}
+EXPORT_SYMBOL_GPL(xlnx_crtc_register);
+
+void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc)
+{
+	struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
+
+	mutex_lock(&helper->lock);
+	list_del(&crtc->list);
+	mutex_unlock(&helper->lock);
+}
+EXPORT_SYMBOL_GPL(xlnx_crtc_unregister);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_crtc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_crtc.h
@@ -0,0 +1,76 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx DRM crtc header
+ *
+ *  Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_CRTC_H_
+#define _XLNX_CRTC_H_
+
+/**
+ * struct xlnx_crtc - Xilinx CRTC device
+ * @crtc: DRM CRTC device
+ * @list: list node for Xilinx CRTC device list
+ * @get_align: Get the alignment requirement of CRTC device
+ * @get_dma_mask: Get the dma mask of CRTC device
+ * @get_max_width: Get the maximum supported width
+ * @get_max_height: Get the maximum supported height
+ * @get_format: Get the current format of CRTC device
+ * @get_cursor_width: Get the cursor width
+ * @get_cursor_height: Get the cursor height
+ */
+struct xlnx_crtc {
+	struct drm_crtc crtc;
+	struct list_head list;
+	unsigned int (*get_align)(struct xlnx_crtc *crtc);
+	u64 (*get_dma_mask)(struct xlnx_crtc *crtc);
+	int (*get_max_width)(struct xlnx_crtc *crtc);
+	int (*get_max_height)(struct xlnx_crtc *crtc);
+	uint32_t (*get_format)(struct xlnx_crtc *crtc);
+	uint32_t (*get_cursor_width)(struct xlnx_crtc *crtc);
+	uint32_t (*get_cursor_height)(struct xlnx_crtc *crtc);
+};
+
+/*
+ * Helper functions: used within Xlnx DRM
+ */
+
+struct xlnx_crtc_helper;
+
+unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper);
+u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper);
+int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper);
+int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper);
+uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper);
+u32 xlnx_crtc_helper_get_cursor_width(struct xlnx_crtc_helper *helper);
+u32 xlnx_crtc_helper_get_cursor_height(struct xlnx_crtc_helper *helper);
+
+struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm);
+void xlnx_crtc_helper_fini(struct drm_device *drm,
+			   struct xlnx_crtc_helper *helper);
+
+/*
+ * CRTC registration: used by other sub-driver modules
+ */
+
+static inline struct xlnx_crtc *to_xlnx_crtc(struct drm_crtc *crtc)
+{
+	return container_of(crtc, struct xlnx_crtc, crtc);
+}
+
+void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc);
+void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc);
+
+#endif /* _XLNX_CRTC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_csc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_csc.c
@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * VPSS CSC DRM bridge driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Venkateshwar rao G <vgannava@xilinx.com>
+ */
+
+/*
+ * Overview:
+ * This experimentatl driver works as a bridge driver and
+ * reused the code from V4L2.
+ * TODO:
+ * Need to implement in a modular approach to share driver code between
+ * V4L2 and DRM frameworks.
+ * Should be integrated with plane
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <uapi/linux/media-bus-format.h>
+
+#include "xlnx_bridge.h"
+
+/* Register offset */
+#define XV_CSC_AP_CTRL			(0x000)
+#define XV_CSC_INVIDEOFORMAT		(0x010)
+#define XV_CSC_OUTVIDEOFORMAT		(0x018)
+#define XV_CSC_WIDTH			(0x020)
+#define XV_CSC_HEIGHT			(0x028)
+#define XV_CSC_K11			(0x050)
+#define XV_CSC_K12			(0x058)
+#define XV_CSC_K13			(0x060)
+#define XV_CSC_K21			(0x068)
+#define XV_CSC_K22			(0x070)
+#define XV_CSC_K23			(0x078)
+#define XV_CSC_K31			(0x080)
+#define XV_CSC_K32			(0x088)
+#define XV_CSC_K33			(0x090)
+#define XV_CSC_ROFFSET			(0x098)
+#define XV_CSC_GOFFSET			(0x0a0)
+#define XV_CSC_BOFFSET			(0x0a8)
+#define XV_CSC_CLAMPMIN			(0x0b0)
+#define XV_CSC_CLIPMAX			(0x0b8)
+#define XV_CSC_SCALE_FACTOR		(4096)
+#define XV_CSC_DIVISOR			(10000)
+/* Streaming Macros */
+#define XCSC_CLAMP_MIN_ZERO		(0)
+#define XCSC_AP_START			BIT(0)
+#define XCSC_AP_AUTO_RESTART		BIT(7)
+#define XCSC_STREAM_ON			(XCSC_AP_START | XCSC_AP_AUTO_RESTART)
+#define XCSC_STREAM_OFF			(0)
+/* GPIO Reset Assert/De-assert */
+#define XCSC_RESET_ASSERT		(1)
+#define XCSC_RESET_DEASSERT		(0)
+
+#define XCSC_MIN_WIDTH			(64)
+#define XCSC_MAX_WIDTH			(8192)
+#define XCSC_MIN_HEIGHT			(64)
+#define XCSC_MAX_HEIGHT			(4320)
+
+static const u32 xilinx_csc_video_fmts[] = {
+	MEDIA_BUS_FMT_RGB888_1X24,
+	MEDIA_BUS_FMT_VUY8_1X24,
+	MEDIA_BUS_FMT_UYVY8_1X16,
+	MEDIA_BUS_FMT_VYYUYY8_1X24,
+};
+
+/* vpss_csc_color_fmt - Color format type */
+enum vpss_csc_color_fmt {
+	XVIDC_CSF_RGB = 0,
+	XVIDC_CSF_YCRCB_444,
+	XVIDC_CSF_YCRCB_422,
+	XVIDC_CSF_YCRCB_420,
+};
+
+/**
+ * struct xilinx_csc - Core configuration of csc device structure
+ * @base: pointer to register base address
+ * @dev: device structure
+ * @bridge: xilinx bridge
+ * @cft_in: input color format
+ * @cft_out: output color format
+ * @color_depth: color depth
+ * @k_hw: array of hardware values
+ * @clip_max: clipping maximum value
+ * @width: width of the video
+ * @height: height of video
+ * @max_width: maximum number of pixels in a line
+ * @max_height: maximum number of lines per frame
+ * @rst_gpio: Handle to GPIO specifier to assert/de-assert the reset line
+ * @aclk: IP clock struct
+ */
+struct xilinx_csc {
+	void __iomem *base;
+	struct device *dev;
+	struct xlnx_bridge bridge;
+	enum vpss_csc_color_fmt cft_in;
+	enum vpss_csc_color_fmt cft_out;
+	u32 color_depth;
+	s32 k_hw[3][4];
+	s32 clip_max;
+	u32 width;
+	u32 height;
+	u32 max_width;
+	u32 max_height;
+	struct gpio_desc *rst_gpio;
+	struct clk *aclk;
+};
+
+static inline void xilinx_csc_write(void __iomem *base, u32 offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static inline u32 xilinx_csc_read(void __iomem *base, u32 offset)
+{
+	return readl(base + offset);
+}
+
+/**
+ * bridge_to_layer - Gets the parent structure
+ * @bridge: pointer to the member.
+ *
+ * Return: parent structure pointer
+ */
+static inline struct xilinx_csc *bridge_to_layer(struct xlnx_bridge *bridge)
+{
+	return container_of(bridge, struct xilinx_csc, bridge);
+}
+
+static void xilinx_csc_write_rgb_3x3(struct xilinx_csc *csc)
+{
+	xilinx_csc_write(csc->base, XV_CSC_K11, csc->k_hw[0][0]);
+	xilinx_csc_write(csc->base, XV_CSC_K12, csc->k_hw[0][1]);
+	xilinx_csc_write(csc->base, XV_CSC_K13, csc->k_hw[0][2]);
+	xilinx_csc_write(csc->base, XV_CSC_K21, csc->k_hw[1][0]);
+	xilinx_csc_write(csc->base, XV_CSC_K22, csc->k_hw[1][1]);
+	xilinx_csc_write(csc->base, XV_CSC_K23, csc->k_hw[1][2]);
+	xilinx_csc_write(csc->base, XV_CSC_K31, csc->k_hw[2][0]);
+	xilinx_csc_write(csc->base, XV_CSC_K32, csc->k_hw[2][1]);
+	xilinx_csc_write(csc->base, XV_CSC_K33, csc->k_hw[2][2]);
+}
+
+static void xilinx_csc_write_rgb_offset(struct xilinx_csc *csc)
+{
+	xilinx_csc_write(csc->base, XV_CSC_ROFFSET, csc->k_hw[0][3]);
+	xilinx_csc_write(csc->base, XV_CSC_GOFFSET, csc->k_hw[1][3]);
+	xilinx_csc_write(csc->base, XV_CSC_BOFFSET, csc->k_hw[2][3]);
+}
+
+static void xilinx_csc_write_coeff(struct xilinx_csc *csc)
+{
+	xilinx_csc_write_rgb_3x3(csc);
+	xilinx_csc_write_rgb_offset(csc);
+}
+
+static void xcsc_set_default_state(struct xilinx_csc *csc)
+{
+	csc->cft_in = XVIDC_CSF_YCRCB_422;
+	csc->cft_out = XVIDC_CSF_YCRCB_422;
+
+	/* This represents an identity matrix mutliped by 2^12 */
+	csc->k_hw[0][0] = XV_CSC_SCALE_FACTOR;
+	csc->k_hw[0][1] = 0;
+	csc->k_hw[0][2] = 0;
+	csc->k_hw[1][0] = 0;
+	csc->k_hw[1][1] = XV_CSC_SCALE_FACTOR;
+	csc->k_hw[1][2] = 0;
+	csc->k_hw[2][0] = 0;
+	csc->k_hw[2][1] = 0;
+	csc->k_hw[2][2] = XV_CSC_SCALE_FACTOR;
+	csc->k_hw[0][3] = 0;
+	csc->k_hw[1][3] = 0;
+	csc->k_hw[2][3] = 0;
+	csc->clip_max = ((1 << csc->color_depth) - 1);
+	xilinx_csc_write(csc->base, XV_CSC_INVIDEOFORMAT, csc->cft_in);
+	xilinx_csc_write(csc->base, XV_CSC_OUTVIDEOFORMAT, csc->cft_out);
+	xilinx_csc_write_coeff(csc);
+	xilinx_csc_write(csc->base, XV_CSC_CLIPMAX, csc->clip_max);
+	xilinx_csc_write(csc->base, XV_CSC_CLAMPMIN, XCSC_CLAMP_MIN_ZERO);
+}
+
+static void xcsc_ycrcb_to_rgb(struct xilinx_csc *csc, s32 *clip_max)
+{
+	u16 bpc_scale = (1 << (csc->color_depth - 8));
+	/*
+	 * See http://graficaobscura.com/matrix/index.html for
+	 * how these numbers are derived. The VPSS CSC IP is
+	 * derived from this Matrix style algorithm. And the
+	 * 'magic' numbers here are derived from the algorithm.
+	 *
+	 * XV_CSC_DIVISOR is used to help with floating constants
+	 * while performing multiplicative operations.
+	 *
+	 * Coefficients valid only for BT 709
+	 */
+	csc->k_hw[0][0] = 11644 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[0][1] = 0;
+	csc->k_hw[0][2] = 17927 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[1][0] = 11644 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[1][1] = -2132 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[1][2] = -5329 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[2][0] = 11644 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[2][1] = 21124 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[2][2] = 0;
+	csc->k_hw[0][3] = -248 * bpc_scale;
+	csc->k_hw[1][3] = 77 * bpc_scale;
+	csc->k_hw[2][3] = -289 * bpc_scale;
+	*clip_max = ((1 << csc->color_depth) - 1);
+}
+
+static void xcsc_rgb_to_ycrcb(struct xilinx_csc *csc, s32 *clip_max)
+{
+	u16 bpc_scale = (1 << (csc->color_depth - 8));
+	/*
+	 * See http://graficaobscura.com/matrix/index.html for
+	 * how these numbers are derived. The VPSS CSC
+	 * derived from this Matrix style algorithm. And the
+	 * 'magic' numbers here are derived from the algorithm.
+	 *
+	 * XV_CSC_DIVISOR is used to help with floating constants
+	 * while performing multiplicative operations.
+	 *
+	 * Coefficients valid only for BT 709
+	 */
+	csc->k_hw[0][0] = 1826 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[0][1] = 6142 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[0][2] = 620 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[1][0] = -1006 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[1][1] = -3386 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[1][2] = 4392 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[2][0] = 4392 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[2][1] = -3989 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[2][2] = -403 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR;
+	csc->k_hw[0][3] = 16 * bpc_scale;
+	csc->k_hw[1][3] = 128 * bpc_scale;
+	csc->k_hw[2][3] = 128 * bpc_scale;
+	*clip_max = ((1 << csc->color_depth) - 1);
+}
+
+/**
+ * xcsc_set_coeff- Sets the coefficients
+ * @csc: Pointer to csc device structure
+ *
+ * This function set the coefficients
+ *
+ */
+static void xcsc_set_coeff(struct xilinx_csc *csc)
+{
+	xilinx_csc_write(csc->base, XV_CSC_INVIDEOFORMAT, csc->cft_in);
+	xilinx_csc_write(csc->base, XV_CSC_OUTVIDEOFORMAT, csc->cft_out);
+	xilinx_csc_write_coeff(csc);
+	xilinx_csc_write(csc->base, XV_CSC_CLIPMAX, csc->clip_max);
+	xilinx_csc_write(csc->base, XV_CSC_CLAMPMIN, XCSC_CLAMP_MIN_ZERO);
+}
+
+/**
+ * xilinx_csc_bridge_enable - enabes csc core
+ * @bridge: bridge instance
+ *
+ * This function enables the csc core
+ *
+ * Return: 0 on success.
+ *
+ */
+static int xilinx_csc_bridge_enable(struct xlnx_bridge *bridge)
+{
+	struct xilinx_csc *csc = bridge_to_layer(bridge);
+
+	xilinx_csc_write(csc->base, XV_CSC_AP_CTRL, XCSC_STREAM_ON);
+
+	return 0;
+}
+
+/**
+ * xilinx_csc_bridge_disable - disables csc core
+ * @bridge: bridge instance
+ *
+ * This function disables the csc core
+ */
+static void xilinx_csc_bridge_disable(struct xlnx_bridge *bridge)
+{
+	struct xilinx_csc *csc = bridge_to_layer(bridge);
+
+	xilinx_csc_write(csc->base, XV_CSC_AP_CTRL, XCSC_STREAM_OFF);
+	/* Reset the Global IP Reset through GPIO */
+	gpiod_set_value_cansleep(csc->rst_gpio, XCSC_RESET_ASSERT);
+	gpiod_set_value_cansleep(csc->rst_gpio, XCSC_RESET_DEASSERT);
+}
+
+/**
+ * xilinx_csc_bridge_set_input - Sets the input parameters of csc
+ * @bridge: bridge instance
+ * @width: width of video
+ * @height: height of video
+ * @bus_fmt: video bus format
+ *
+ * This function sets the input parameters of csc
+ * Return: 0 on success. -EINVAL for invalid parameters.
+ */
+static int xilinx_csc_bridge_set_input(struct xlnx_bridge *bridge, u32 width,
+				       u32 height, u32 bus_fmt)
+{
+	struct xilinx_csc *csc = bridge_to_layer(bridge);
+
+	xcsc_set_default_state(csc);
+
+	if (height > csc->max_height || height < XCSC_MIN_HEIGHT)
+		return -EINVAL;
+
+	if (width > csc->max_width || width < XCSC_MIN_WIDTH)
+		return -EINVAL;
+
+	csc->height = height;
+	csc->width = width;
+
+	switch (bus_fmt) {
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		csc->cft_in = XVIDC_CSF_RGB;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+		csc->cft_in = XVIDC_CSF_YCRCB_444;
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+		csc->cft_in = XVIDC_CSF_YCRCB_422;
+		break;
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		csc->cft_in = XVIDC_CSF_YCRCB_420;
+		break;
+	default:
+		dev_dbg(csc->dev, "unsupported input video format\n");
+		return -EINVAL;
+	}
+
+	xilinx_csc_write(csc->base, XV_CSC_WIDTH, width);
+	xilinx_csc_write(csc->base, XV_CSC_HEIGHT, height);
+
+	return 0;
+}
+
+/**
+ * xilinx_csc_bridge_get_input_fmts - input formats supported by csc
+ * @bridge: bridge instance
+ * @fmts: Pointer to be updated with formats information
+ * @count: count of video bus formats
+ *
+ * This function provides the input video formats information csc
+ * Return: 0 on success.
+ */
+static int xilinx_csc_bridge_get_input_fmts(struct xlnx_bridge *bridge,
+					    const u32 **fmts, u32 *count)
+{
+	*fmts = xilinx_csc_video_fmts;
+	*count = ARRAY_SIZE(xilinx_csc_video_fmts);
+
+	return 0;
+}
+
+/**
+ * xilinx_csc_bridge_set_output - Sets the output parameters of csc
+ * @bridge: bridge instance
+ * @width: width of video
+ * @height: height of video
+ * @bus_fmt: video bus format
+ *
+ * This function sets the output parameters of csc
+ * Return: 0 on success. -EINVAL for invalid parameters.
+ */
+static int xilinx_csc_bridge_set_output(struct xlnx_bridge *bridge, u32 width,
+					u32 height, u32 bus_fmt)
+{
+	struct xilinx_csc *csc = bridge_to_layer(bridge);
+
+	if (width != csc->width || height != csc->height)
+		return -EINVAL;
+
+	switch (bus_fmt) {
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		csc->cft_out = XVIDC_CSF_RGB;
+		dev_dbg(csc->dev, "Media Format Out : RGB");
+		if (csc->cft_in != MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_ycrcb_to_rgb(csc, &csc->clip_max);
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+		csc->cft_out = XVIDC_CSF_YCRCB_444;
+		dev_dbg(csc->dev, "Media Format Out : YUV 444");
+		if (csc->cft_in == MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_rgb_to_ycrcb(csc, &csc->clip_max);
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+		csc->cft_out = XVIDC_CSF_YCRCB_422;
+		dev_dbg(csc->dev, "Media Format Out : YUV 422");
+		if (csc->cft_in == MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_rgb_to_ycrcb(csc, &csc->clip_max);
+		break;
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		csc->cft_out = XVIDC_CSF_YCRCB_420;
+		dev_dbg(csc->dev, "Media Format Out : YUV 420");
+		if (csc->cft_in == MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_rgb_to_ycrcb(csc, &csc->clip_max);
+		break;
+	default:
+		dev_info(csc->dev, "unsupported output video format\n");
+		return -EINVAL;
+	}
+	xcsc_set_coeff(csc);
+
+	return 0;
+}
+
+/**
+ * xilinx_csc_bridge_get_output_fmts - output formats supported by csc
+ * @bridge: bridge instance
+ * @fmts: Pointer to be updated with formats information
+ * @count: count of video bus formats
+ *
+ * This function provides the output video formats information csc
+ * Return: 0 on success.
+ */
+static int xilinx_csc_bridge_get_output_fmts(struct xlnx_bridge *bridge,
+					     const u32 **fmts, u32 *count)
+{
+	*fmts = xilinx_csc_video_fmts;
+	*count = ARRAY_SIZE(xilinx_csc_video_fmts);
+	return 0;
+}
+
+static int xcsc_parse_of(struct xilinx_csc *csc)
+{
+	int ret;
+	struct device_node *node = csc->dev->of_node;
+
+	csc->aclk = devm_clk_get(csc->dev, NULL);
+	if (IS_ERR(csc->aclk)) {
+		ret = PTR_ERR(csc->aclk);
+		dev_err(csc->dev, "failed to get aclk %d\n", ret);
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,video-width",
+				   &csc->color_depth);
+	if (ret < 0) {
+		dev_info(csc->dev, "video width not present in DT\n");
+		return ret;
+	}
+	if (csc->color_depth != 8 && csc->color_depth != 10 &&
+	    csc->color_depth != 12 && csc->color_depth != 16) {
+		dev_err(csc->dev, "Invalid video width in DT\n");
+		return -EINVAL;
+	}
+	/* Reset GPIO */
+	csc->rst_gpio = devm_gpiod_get(csc->dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(csc->rst_gpio)) {
+		if (PTR_ERR(csc->rst_gpio) != -EPROBE_DEFER)
+			dev_err(csc->dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(csc->rst_gpio);
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-height", &csc->max_height);
+	if (ret < 0) {
+		dev_err(csc->dev, "xlnx,max-height is missing!");
+		return -EINVAL;
+	} else if (csc->max_height > XCSC_MAX_HEIGHT ||
+		   csc->max_height < XCSC_MIN_HEIGHT) {
+		dev_err(csc->dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-width", &csc->max_width);
+	if (ret < 0) {
+		dev_err(csc->dev, "xlnx,max-width is missing!");
+		return -EINVAL;
+	} else if (csc->max_width > XCSC_MAX_WIDTH ||
+		   csc->max_width < XCSC_MIN_WIDTH) {
+		dev_err(csc->dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int xilinx_csc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct xilinx_csc *csc;
+	int ret;
+
+	csc = devm_kzalloc(dev, sizeof(*csc), GFP_KERNEL);
+	if (!csc)
+		return -ENOMEM;
+
+	csc->dev = dev;
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	csc->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(csc->base))
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, csc);
+	ret = xcsc_parse_of(csc);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_prepare_enable(csc->aclk);
+	if (ret) {
+		dev_err(csc->dev, "failed to enable clock %d\n", ret);
+		return ret;
+	}
+
+	gpiod_set_value_cansleep(csc->rst_gpio, XCSC_RESET_DEASSERT);
+	csc->bridge.enable = &xilinx_csc_bridge_enable;
+	csc->bridge.disable = &xilinx_csc_bridge_disable;
+	csc->bridge.set_input = &xilinx_csc_bridge_set_input;
+	csc->bridge.get_input_fmts = &xilinx_csc_bridge_get_input_fmts;
+	csc->bridge.set_output = &xilinx_csc_bridge_set_output;
+	csc->bridge.get_output_fmts = &xilinx_csc_bridge_get_output_fmts;
+	csc->bridge.of_node = dev->of_node;
+
+	ret = xlnx_bridge_register(&csc->bridge);
+	if (ret) {
+		dev_info(csc->dev, "Bridge registration failed\n");
+		goto err_clk;
+	}
+
+	dev_info(csc->dev, "Xilinx VPSS CSC DRM experimental driver probed\n");
+
+	return 0;
+
+err_clk:
+	clk_disable_unprepare(csc->aclk);
+	return ret;
+}
+
+static int xilinx_csc_remove(struct platform_device *pdev)
+{
+	struct xilinx_csc *csc = platform_get_drvdata(pdev);
+
+	xlnx_bridge_unregister(&csc->bridge);
+	clk_disable_unprepare(csc->aclk);
+
+	return 0;
+}
+
+static const struct of_device_id xilinx_csc_of_match[] = {
+	{ .compatible = "xlnx,vpss-csc"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xilinx_csc_of_match);
+
+static struct platform_driver csc_bridge_driver = {
+	.probe = xilinx_csc_probe,
+	.remove = xilinx_csc_remove,
+	.driver = {
+		.name = "xlnx,csc-bridge",
+		.of_match_table = xilinx_csc_of_match,
+	},
+};
+
+module_platform_driver(csc_bridge_driver);
+
+MODULE_AUTHOR("Venkateshwar Rao <vgannava@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx FPGA CSC Bridge Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_dptx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_dptx.c
@@ -0,0 +1,3546 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA DisplayPort TX Subsystem Driver
+ *
+ *  Copyright (C) 2020 Xilinx, Inc.
+ *
+ * Author: Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>
+ *	 : Venkateshwar Rao G <vgannava.xilinx.com>
+ *
+ */
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-dp.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_dp_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_of.h>
+#include <drm/drm_probe_helper.h>
+#include <linux/hdmi.h>
+#include <sound/soc.h>
+#include <sound/pcm_drm_eld.h>
+
+/* Link configuration registers */
+#define XDPTX_LINKBW_SET_REG			0x0
+#define XDPTX_LANECNT_SET_REG			0x4
+#define XDPTX_DPCD_LANECNT_SET_MASK		GENMASK(4, 0)
+#define XDPTX_EFRAME_EN_REG			0x8
+#define XDPTX_TRNGPAT_SET_REG			0xc
+#define XDPTX_SCRAMBLING_DIS_REG		0x14
+#define XDPTX_DOWNSPREAD_CTL_REG		0x18
+#define XDPTX_DPCD_SPREAD_AMP_MASK		BIT(4)
+#define XDPTX_SOFT_RST				0x1c
+#define XDPTX_SOFT_RST_VIDEO_STREAM_ALL_MASK	GENMASK(3, 0)
+#define XDPTX_SOFT_RST_HDCP_MASK		BIT(8)
+
+/* GtCtrl Registers */
+#define XDPTX_GTCTL_REG				0x4c
+#define XDPTX_GTCTL_VSWING_MASK			GENMASK(12, 8)
+#define XDPTX_GTCTL_POST_CUR_MASK		GENMASK(22, 18)
+#define XDPTX_GTCTL_LINE_RATE_MASK		GENMASK(2, 1)
+#define XDPTX_GTCTL_LINE_RATE_810G		0x03
+#define XDPTX_GTCTL_LINE_RATE_540G		0x02
+#define XDPTX_GTCTL_LINE_RATE_270G		0x01
+#define XDPTX_GTCTL_LINE_RATE_162G		0x00
+
+/* GTHE4 */
+#define XVPHY_GTHE4_DIFF_SWING_DP_V0P0		0x01
+#define XVPHY_GTHE4_DIFF_SWING_DP_V0P1		0x02
+#define XVPHY_GTHE4_DIFF_SWING_DP_V0P2		0x05
+#define XVPHY_GTHE4_DIFF_SWING_DP_V0P3		0x0b
+#define XVPHY_GTHE4_DIFF_SWING_DP_V1P0		0x02
+#define XVPHY_GTHE4_DIFF_SWING_DP_V1P1		0x05
+#define XVPHY_GTHE4_DIFF_SWING_DP_V1P2		0x07
+#define XVPHY_GTHE4_DIFF_SWING_DP_V2P0		0x04
+#define XVPHY_GTHE4_DIFF_SWING_DP_V2P1		0x07
+#define XVPHY_GTHE4_DIFF_SWING_DP_V3P0		0x08
+#define XVPHY_GTHE4_PREEMP_DP_L0		0x03
+#define XVPHY_GTHE4_PREEMP_DP_L1		0x0d
+#define XVPHY_GTHE4_PREEMP_DP_L2		0x16
+#define XVPHY_GTHE4_PREEMP_DP_L3		0x1d
+
+/* DPTX Core enable registers */
+#define XDPTX_ENABLE_REG			0x80
+#define XDPTX_MAINSTRM_ENABLE_REG		0x84
+#define XDPTX_SCRAMBLER_RESET			0xc0
+#define XDPTX_SCRAMBLER_RESET_MASK		BIT(0)
+#define XDPTX_MST_CONFIG			0xd0
+
+/* AUX channel interface registers */
+#define XDPTX_AUXCMD_REG			0x100
+#define XDPTX_AUX_WRITEFIFO_REG			0x104
+#define XDPTX_AUX_ADDR_REG			0x108
+#define XDPTX_AUXCMD_ADDRONLY_MASK		BIT(12)
+#define XDPTX_AUXCMD_SHIFT			0x8
+#define XDPTX_AUXCMD_BYTES_SHIFT		0x0
+#define XDPTX_AUX_READ_BIT				0x1
+
+#define XDPTX_CLKDIV_REG			0x10c
+#define XDPTX_CLKDIV_MHZ			1000000
+#define XDPTX_CLKDIV_AUXFILTER_SHIFT		0x8
+
+#define XDPTX_INTR_SIGSTATE_REG			0x130
+#define XDPTX_INTR_SIGHPDSTATE			BIT(0)
+#define XDPTX_INTR_SIGREQSTATE			BIT(1)
+#define XDPTX_INTR_SIGRPLYSTATE			BIT(2)
+#define XDPTX_INTR_RPLYTIMEOUT			BIT(3)
+
+#define XDPTX_AUXREPLY_DATA_REG			0x134
+#define XDPTX_AUXREPLY_CODE_REG			0x138
+#define XDPTX_AUXREPLYCODE_AUXACK_MASK		(0)
+#define XDPTX_AUXREPLYCODE_I2CACK_MASK		(0)
+
+#define XDPTX_AUXREPLY_DATACNT_REG		0x148
+#define XDPTX_AUXREPLY_DATACNT_MASK		GENMASK(7, 0)
+#define XDPTX_INTR_STATUS_REG			0x140
+#define XDPTX_INTR_MASK_REG			0x144
+#define XDPTX_INTR_HPDEVENT_MASK		BIT(1)
+#define XDPTX_INTR_HPDPULSE_MASK		BIT(4)
+#define XDPTX_INTR_CHBUFUNDFW_MASK		GENMASK(21, 16)
+#define XDPTX_INTR_CHBUFOVFW_MASK		GENMASK(27, 22)
+#define XDPTX_INTR_VBLANK_MASK			BIT(10)
+#define XDPTX_INTR_EXTPKT_TXD_MASK		BIT(5)
+#define XDPTX_HPD_DURATION_REG			0x150
+
+/* Main stream attribute registers */
+#define XDPTX_MAINSTRM_HTOTAL_REG		0x180
+#define XDPTX_MAINSTRM_VTOTAL_REG		0x184
+#define XDPTX_MAINSTRM_POL_REG			0x188
+#define XDPTX_MAINSTRM_POLHSYNC_SHIFT		0x0
+#define XDPTX_MAINSTRM_POLVSYNC_SHIFT		0x1
+#define XDPTX_MAINSTRM_HSWIDTH_REG		0x18c
+#define XDPTX_MAINSTRM_VSWIDTH_REG		0x190
+#define XDPTX_MAINSTRM_HRES_REG			0x194
+#define XDPTX_MAINSTRM_VRES_REG			0x198
+#define XDPTX_MAINSTRM_HSTART_REG		0x19c
+#define XDPTX_MAINSTRM_VSTART_REG		0x1a0
+#define XDPTX_MAINSTRM_MISC0_REG		0x1a4
+#define XDPTX_MAINSTRM_MISC0_MASK		BIT(0)
+#define XDPTX_MAINSTRM_MISC0_EXT_VSYNC_MASK	BIT(12)
+#define XDPTX_MAINSTRM_MISC1_REG		0x1a8
+#define XDPTX_MAINSTRM_MISC1_TIMING_IGNORED_MASK BIT(6)
+
+#define XDPTX_M_VID_REG				0x1ac
+#define XDPTX_TRANSFER_UNITSIZE_REG		0x1b0
+#define XDPTX_DEF_TRANSFER_UNITSIZE		0x40
+#define XDPTX_N_VID_REG				0x1b4
+#define XDPTX_USER_PIXELWIDTH_REG		0x1b8
+#define XDPTX_USER_DATACNTPERLANE_REG		0x1bc
+#define XDPTX_MINBYTES_PERTU_REG		0x1c4
+#define XDPTX_FRACBYTES_PERTU_REG		0x1c8
+#define XDPTX_INIT_WAIT_REG			0x1cc
+
+/* PHY configuration and status registers */
+#define XDPTX_PHYCONFIG_REG			0x200
+#define XDPTX_PHYCONFIG_RESET_MASK		BIT(0)
+#define XDPTX_PHYCONFIG_GTTXRESET_MASK		BIT(1)
+#define XDPTX_PHYCONFIG_PMARESET_MASK		BIT(8)
+#define XDPTX_PHYCONFIG_PCSRESET_MASK		BIT(9)
+#define XDPTX_PHYCONFIG_ALLRESET_MASK	(XDPTX_PHYCONFIG_RESET_MASK | \
+					 XDPTX_PHYCONFIG_GTTXRESET_MASK | \
+					 XDPTX_PHYCONFIG_PMARESET_MASK | \
+					 XDPTX_PHYCONFIG_PCSRESET_MASK)
+
+#define XDPTX_PHYCLOCK_FBSETTING_REG		0x234
+#define XDPTX_PHYCLOCK_FBSETTING162_MASK	0x1
+#define XDPTX_PHYCLOCK_FBSETTING270_MASK	0x3
+#define XDPTX_PHYCLOCK_FBSETTING810_MASK	0x5
+
+#define XDPTX_VS_PE_LEVEL_MAXCOUNT		3
+#define XDPTX_VS_LEVEL_MAXCOUNT			0x5
+
+#define XDPTX_PHYSTATUS_REG			0x280
+#define XDPTX_PHYSTATUS_FPGAPLLLOCK_MASK	BIT(6)
+#define XDPTX_MAX_RATE(bw, lanecnt, bpp)	((bw) * (lanecnt) * 8 / (bpp))
+
+#define XDPTX_MISC0_RGB_MASK			(0)
+#define XDPTX_MISC0_YCRCB422_MASK		(5 << 1)
+#define XDPTX_MISC0_YCRCB444_MASK		GENMASK(3, 2)
+#define XDPTX_MISC0_FORMAT_MASK			GENMASK(3, 1)
+#define XDPTX_MISC0_BPC6_MASK			(0 << 5)
+#define XDPTX_MISC0_BPC8_MASK			BIT(5)
+#define XDPTX_MISC0_BPC10_MASK			BIT(6)
+#define XDPTX_MISC0_BPC12_MASK			GENMASK(6, 5)
+#define XDPTX_MISC0_BPC16_MASK			BIT(7)
+#define XDPTX_MISC0_BPC_MASK			GENMASK(7, 5)
+#define XDPTX_MISC1_YONLY_MASK			BIT(7)
+
+#define XDPTX_MAX_LANES				0x4
+#define XDPTX_MAX_FREQ				3000000
+#define XDPTX_SINK_PWR_CYCLES			3
+
+#define XDPTX_REDUCED_BIT_RATE			162000
+#define XDPTX_HIGH_BIT_RATE_1			270000
+#define XDPTX_HIGH_BIT_RATE_2			540000
+#define XDPTX_HIGH_BIT_RATE_3			810000
+
+#define XDPTX_V1_2				0x12
+#define XDPTX_V1_4				0x14
+
+#define XDP_TRAIN_MAX_SWING_REACHED			BIT(2)
+#define XDP_TRAIN_PRE_EMPHASIS_SHIFT			GENMASK(1, 0)
+#define XDP_DPCD_TRAINING_LANEX_SET_MAX_PE_MASK		BIT(5)
+
+#define XDPTX_PHYPRECURSOR_LANE0_REG			0x23c
+#define XDPTX_PHYPOSTCURSOR_LANE0_REG			0x24c
+
+/* Transceiver PHY reset and Differential voltage swing */
+#define XDPTX_PHYVOLTAGE_DIFFLANE0_REG			0x220
+#define XDPTX_VS_LEVEL_OFFSET				0x4
+
+#define XDPTX_VTC_BASE					0x1000
+
+/* VTC register offsets and bit masks */
+#define XDPTX_VTC_CTL					0x000
+#define XDPTX_VTC_CTL_MASK				GENMASK(18, 8)
+#define XDPTX_VTC_CTL_GE				BIT(2)
+#define XDPTX_VTC_CTL_RU				BIT(1)
+
+#define XDPTX_VTC_GASIZE_F0				0x060
+#define XDPTX_VTC_ACTIVE_SIZE_MASK			GENMASK(12, 0)
+
+#define XDPTX_VTC_GFENC					0x068
+#define XDPTX_VTC_GFENC_MASK				BIT(6)
+
+#define XDPTX_VTC_GPOL					0x06c
+#define XDPTX_VTC_GPOL_FIELD_ID_POL			BIT(6)
+#define XDPTX_VTC_ACTIVE_CHROMA_POL			BIT(5)
+#define	XDPTX_VTC_ACTIVE_VIDEO_POL			BIT(4)
+#define XDPTX_VTC_HSYNC_POL				BIT(3)
+#define XDPTX_VTC_VSYNC_POL				BIT(2)
+#define XDPTX_VTC_HBLANK_POL				BIT(1)
+#define XDPTX_VTC_VBLANK_POL				BIT(0)
+#define XDPTX_VTC_GPOL_MASK		(XDPTX_VTC_VBLANK_POL |\
+					 XDPTX_VTC_HBLANK_POL |\
+					 XDPTX_VTC_VSYNC_POL |\
+					 XDPTX_VTC_HSYNC_POL |\
+					 XDPTX_VTC_ACTIVE_VIDEO_POL |\
+					 XDPTX_VTC_ACTIVE_CHROMA_POL)
+
+#define XDPTX_VTC_INT_GPOL_MASK		(XDPTX_VTC_GPOL_FIELD_ID_POL |\
+					 XDPTX_VTC_ACTIVE_CHROMA_POL |\
+					 XDPTX_VTC_ACTIVE_VIDEO_POL)
+
+#define XDPTX_VTC_GHSIZE				0x070
+#define XDPTX_VTC_GHSIZE_FRAME_HSIZE			GENMASK(12, 0)
+
+#define XDPTX_VTC_GVSIZE				0x074
+#define XDPTX_VTC_FIELD1_VSIZE_SHIFT			16
+#define XDPTX_VTC_GVSIZE_FRAME_VSIZE			GENMASK(12, 0)
+
+#define XDPTX_VTC_GHSYNC				0x078
+#define XDPTX_VTC_GH1BPSTART_SHIFT			16
+#define XDPTX_VTC_GHSYNC_END_MASK			GENMASK(28, 16)
+#define XDPTX_VTC_GHSYNC_START_MASK			GENMASK(12, 0)
+
+#define XDPTX_VTC_GVBHOFF				0x07c
+#define XDPTX_VTC_F0VSYNC_HEND_SHIFT			16
+#define XDPTX_VTC_F0VBLANK_HEND_MASK			GENMASK(28, 16)
+#define XDPTX_VTC_F0VBLANK_HSTART_MASK			GENMASK(12, 0)
+
+#define XDPTX_VTC_GVSYNC				0x080
+#define XDPTX_VTC_F0_VSYNC_VEND_MASK			GENMASK(28, 16)
+#define XDPTX_VTC_F0_VSYNC_VSTART_MASK			GENMASK(12, 0)
+
+#define XDPTX_VTC_GVSHOFF				0x084
+#define XDPTX_VTC_GVBHOFF_F1				0x088
+#define XDPTX_VTC_GVSYNC_F1				0x08c
+#define XDPTX_VTC_GVSHOFF_F1				0x090
+#define XDPTX_VTC_GASIZE_F1				0x094
+/*
+ * This is sleep time in milliseconds before start training and it can be
+ * modified as per the monitor
+ */
+#define XDPTX_POWERON_DELAY_MS				4
+#define XDPTX_AUDIO_CTRL_REG				0x300
+#define XDPTX_AUDIO_EN_MASK				BIT(0)
+#define XDPTX_AUDIO_MUTE_MASK				BIT(16)
+#define XDPTX_AUDIO_CHANNELS_REG			0x304
+#define XDPTX_AUDIO_INFO_DATA_REG			0x308
+#define XDPTX_AUDIO_MAUD_REG				0x328
+#define XDPTX_AUDIO_NAUD_REG				0x32C
+#define XDPTX_AUDIO_INFO_BUFF_STATUS			0x6A0
+#define XDPTX_AUDIO_INFO_BUFF_FULL			BIT(0)
+#define XDPTX_AUDIO_INFO_BUFF_OVERFLOW			BIT(1)
+
+#define DP_INFOFRAME_FIFO_SIZE_WORDS	8
+#define DP_INFOFRAME_FIFO_SIZE		(DP_INFOFRAME_FIFO_SIZE_WORDS * 4)
+#define DP_INFOFRAME_HEADER_SIZE	4
+#define DP_AUDIO_INFOFRAME_SIZE		10
+
+#define DP_INFOFRAME_SIZE(type)	\
+	(DP_INFOFRAME_HEADER_SIZE + DP_ ## type ## _INFOFRAME_SIZE)
+#define XDPTX_AUDIO_EXT_DATA(NUM)	(0x330 + 4 * ((NUM) - 1))
+#define XDPTX_AUDIO_EXT_DATA_2ND_TO_9TH_WORD		8
+#define XDPTX_VSC_SDP_PIXELENC_HEADER_MASK		0x13050700
+#define XDPTX_VSC_SDP_DYNAMIC_RANGE_SHIFT		15
+#define XDPTX_VSC_SDP_BPC_SHIFT				8
+#define XDPTX_VSC_SDP_BPC_MASK				GENMASK(2, 0)
+#define XDPTX_VSC_SDP_FMT_SHIFT				4
+
+#define DP_LINK_BW_SET_MASK			GENMASK(4, 0)
+#define DP_MAX_TRAINING_TRIES				5
+
+#define XDPTX_DP_LANE_COUNT_1				0x01
+#define XDPTX_DP_LANE_COUNT_2				0x02
+#define XDPTX_DP_LANE_COUNT_4				0x04
+
+#define XDPTX_DPCD_LANE02_CRDONE_MASK			0x01
+#define XDPTX_DPCD_LANE13_CRDONE_MASK			0x10
+
+#define XDPTX_LANE0_CRDONE_MASK				0x0
+#define XDPTX_LANE1_CRDONE_MASK				0x1
+#define XDPTX_LANE2_CRDONE_MASK				0x2
+#define XDPTX_LANE3_CRDONE_MASK				0x3
+
+#define I2S_FORMATS	(SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S16_BE |\
+			 SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S20_3BE |\
+			 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_3BE |\
+			 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S24_BE |\
+			 SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_S32_BE |\
+			 SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_LE)
+#define DP_RATES	(SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 |\
+			 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 |\
+			 SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_176400 |\
+			 SNDRV_PCM_RATE_192000)
+/*
+ * CEA speaker placement
+ *
+ *  FL  FLC   FC   FRC   FR   FRW
+ *
+ *                                  LFE
+ *
+ *  RL  RLC   RC   RRC   RR
+ */
+enum dp_codec_cea_spk_placement {
+	FL  = BIT(0),	/* Front Left           */
+	FC  = BIT(1),	/* Front Center         */
+	FR  = BIT(2),	/* Front Right          */
+	FLC = BIT(3),	/* Front Left Center    */
+	FRC = BIT(4),	/* Front Right Center   */
+	RL  = BIT(5),	/* Rear Left            */
+	RC  = BIT(6),	/* Rear Center          */
+	RR  = BIT(7),	/* Rear Right           */
+	RLC = BIT(8),	/* Rear Left Center     */
+	RRC = BIT(9),	/* Rear Right Center    */
+	LFE = BIT(10),	/* Low Frequency Effect */
+};
+
+/*
+ * cea Speaker allocation structure
+ */
+struct dp_codec_cea_spk_alloc {
+	const int ca_id;
+	unsigned int n_ch;
+	unsigned long mask;
+};
+
+/**
+ * struct xlnx_dptx_audio_data - Audio data structure
+ * @buffer: Audio infoframe data buffer
+ */
+struct xlnx_dptx_audio_data {
+	u32 buffer[DP_INFOFRAME_FIFO_SIZE_WORDS];
+};
+
+/**
+ * struct xlnx_dp_vscpkt: VSC extended packet structure
+ * @payload: VSC packet payload bytes from DB0 to DB28
+ * @header: VSC packet header
+ * @bpc: Number of bits per color component
+ * @fmt: The color format currenctly in use by the video stream
+ * @dynamic_range: The dynamic range colorimetry currenctly in use by te video stream
+ * @ycbcr_colorimetry: The ycbcr colorimetry currently in use by te video stream
+ */
+struct xlnx_dp_vscpkt {
+	u32 payload[8];
+	u32 header;
+	u32 bpc;
+	u8 fmt;
+	u8 dynamic_range;
+	u8 ycbcr_colorimetry;
+};
+
+/*
+ * struct xlnx_dp_link_config - Common link config between source and sink
+ * @max_rate: Miaximum link rate
+ * @max_lanes: Maximum number of lanes
+ */
+struct xlnx_dp_link_config {
+	int max_rate;
+	u8 max_lanes;
+	int link_rate;
+	u8 lane_count;
+	u8 cr_done_cnt;
+	u8 cr_done_oldstate;
+};
+
+/**
+ * struct xlnx_dp_tx_link_config - configuration information of the source
+ * @vs_level: voltage swing level
+ * @pe_level: pre emphasis level
+ */
+struct xlnx_dp_tx_link_config {
+	u8 vs_level;
+	u8 pe_level;
+};
+
+/**
+ * struct xlnx_dp_mode - Configured mode of DisplayPort
+ * @pclock: pixel clock frequency of current mode
+ * @bw_code: code for bandwidth(link rate)
+ * @lane_cnt: number of lanes
+ */
+struct xlnx_dp_mode {
+	int pclock;
+	u8 bw_code;
+	u8 lane_cnt;
+};
+
+/**
+ * struct xlnx_dp_config - Configuration of DisplayPort from DTS
+ * @max_lanes: Maximum number of lanes
+ * @max_link_rate: Maximum supported link rate
+ * @misc0: Misc0 configuration
+ * @bpp: Bits per pixel
+ * @bpc: Bits per component
+ * @num_colors: Number of color components
+ * @ppc: Pixels per component
+ * @fmt: Color format
+ * @audio_enabled: flag to indicate audio is enabled in device tree
+ * @versal_gt_present: flag to indicate versal-gt property in device tree
+ */
+struct xlnx_dp_config {
+	u32 max_lanes;
+	u32 max_link_rate;
+	u8 misc0;
+	u8 bpp;
+	u8 bpc;
+	u8 num_colors;
+	u8 ppc;
+	u8 fmt;
+	bool audio_enabled;
+	bool versal_gt_present;
+};
+
+enum xlnx_dp_train_state {
+	XLNX_DP_TRAIN_CR = 0,
+	XLNX_DP_TRAIN_CE = 1,
+	XLNX_DP_ADJUST_LINKRATE = 2,
+	XLNX_DP_ADJUST_LANECOUNT = 3,
+	XLNX_DP_TRAIN_FAILURE = 4,
+	XLNX_DP_TRAIN_SUCCESS = 5
+};
+
+/**
+ * struct xlnx_dp - Xilinx DisplayPort core
+ * @dev: device structure
+ * @encoder: the drm encoder structure
+ * @connector: the drm connector structure
+ * @sync_prop: synchronous mode property
+ * @bpc_prop: bpc mode property
+ * @aux: aux channel
+ * @config: IP core configuration from DTS
+ * @tx_link_config: source configuration
+ * @rx_config: sink configuration
+ * @link_config: common link configuration between IP core and sink device
+ * @drm: DRM core
+ * @mode: current mode between IP core and sink device
+ * @phy: PHY handles for DP lanes
+ * @axi_lite_clk: axi lite clock
+ * @tx_vid_clk: tx video clock
+ * @reset_gpio: reset gpio
+ * @hpd_work: hot plug detection worker
+ * @hpd_pulse_work: hot plug pulse detection worker
+ * @tx_audio_data: audio data
+ * @vscpkt: VSC extended packet data
+ * @phy_opts: Opaque generic phy configuration
+ * @status: connection status
+ * @dp_base: Base address of DisplayPort Tx subsystem
+ * @dpms: current dpms state
+ * @dpcd: DP configuration data from currently connected sink device
+ * @train_set: set of training data
+ * @num_lanes: number of enabled phy lanes
+ * @enabled: flag to indicate if the device is enabled
+ * @audio_init: flag to indicate audio is initialized
+ * @have_edid: flag to indicate if edid is available
+ * @colorimetry_through_vsc: colorimetry information through vsc packets
+ *
+ */
+struct xlnx_dp {
+	struct device *dev;
+	struct drm_encoder encoder;
+	struct drm_connector connector;
+	struct drm_property *sync_prop;
+	struct drm_property *bpc_prop;
+	struct drm_dp_aux aux;
+	struct xlnx_dp_config config;
+	struct xlnx_dp_tx_link_config tx_link_config;
+	struct xlnx_dp_link_config link_config;
+	struct drm_device *drm;
+	struct xlnx_dp_mode mode;
+	struct phy *phy[XDPTX_MAX_LANES];
+	struct clk *axi_lite_clk;
+	struct clk *tx_vid_clk;
+	struct gpio_desc *reset_gpio;
+	struct delayed_work hpd_work;
+	struct delayed_work hpd_pulse_work;
+	struct xlnx_dptx_audio_data *tx_audio_data;
+	struct xlnx_dp_vscpkt vscpkt;
+	union phy_configure_opts phy_opts;
+	enum drm_connector_status status;
+	void __iomem *dp_base;
+	int dpms;
+	u8 dpcd[DP_RECEIVER_CAP_SIZE];
+	u8 train_set[XDPTX_MAX_LANES];
+	u8 num_lanes;
+	unsigned int enabled : 1;
+	bool audio_init;
+	bool have_edid;
+	unsigned int colorimetry_through_vsc : 1;
+};
+
+/*
+ * dp_codec_channel_alloc: speaker configuration available for CEA
+ *
+ * This is an ordered list that must match with dp_codec_8ch_chmaps struct
+ * The preceding ones have better chances to be selected by
+ * dp_codec_get_ch_alloc_table_idx().
+ */
+static const struct dp_codec_cea_spk_alloc dp_codec_channel_alloc[] = {
+	{ .ca_id = 0x00, .n_ch = 2,
+	  .mask = FL | FR},
+	/* 2.1 */
+	{ .ca_id = 0x01, .n_ch = 4,
+	  .mask = FL | FR | LFE},
+	/* Dolby Surround */
+	{ .ca_id = 0x02, .n_ch = 4,
+	  .mask = FL | FR | FC },
+	/* surround51 */
+	{ .ca_id = 0x0b, .n_ch = 6,
+	  .mask = FL | FR | LFE | FC | RL | RR},
+	/* surround40 */
+	{ .ca_id = 0x08, .n_ch = 6,
+	  .mask = FL | FR | RL | RR },
+	/* surround41 */
+	{ .ca_id = 0x09, .n_ch = 6,
+	  .mask = FL | FR | LFE | RL | RR },
+	/* surround50 */
+	{ .ca_id = 0x0a, .n_ch = 6,
+	  .mask = FL | FR | FC | RL | RR },
+	/* 6.1 */
+	{ .ca_id = 0x0f, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | RC },
+	/* surround71 */
+	{ .ca_id = 0x13, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | RLC | RRC },
+	/* others */
+	{ .ca_id = 0x03, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC },
+	{ .ca_id = 0x04, .n_ch = 8,
+	  .mask = FL | FR | RC},
+	{ .ca_id = 0x05, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC },
+	{ .ca_id = 0x06, .n_ch = 8,
+	  .mask = FL | FR | FC | RC },
+	{ .ca_id = 0x07, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RC },
+	{ .ca_id = 0x0c, .n_ch = 8,
+	  .mask = FL | FR | RC | RL | RR },
+	{ .ca_id = 0x0d, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | RC },
+	{ .ca_id = 0x0e, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | RC },
+	{ .ca_id = 0x10, .n_ch = 8,
+	  .mask = FL | FR | RL | RR | RLC | RRC },
+	{ .ca_id = 0x11, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | RLC | RRC },
+	{ .ca_id = 0x12, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | RLC | RRC },
+	{ .ca_id = 0x14, .n_ch = 8,
+	  .mask = FL | FR | FLC | FRC },
+	{ .ca_id = 0x15, .n_ch = 8,
+	  .mask = FL | FR | LFE | FLC | FRC },
+	{ .ca_id = 0x16, .n_ch = 8,
+	  .mask = FL | FR | FC | FLC | FRC },
+	{ .ca_id = 0x17, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | FLC | FRC },
+	{ .ca_id = 0x18, .n_ch = 8,
+	  .mask = FL | FR | RC | FLC | FRC },
+	{ .ca_id = 0x19, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC | FLC | FRC },
+	{ .ca_id = 0x1a, .n_ch = 8,
+	  .mask = FL | FR | RC | FC | FLC | FRC },
+	{ .ca_id = 0x1b, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC | FC | FLC | FRC },
+	{ .ca_id = 0x1c, .n_ch = 8,
+	  .mask = FL | FR | RL | RR | FLC | FRC },
+	{ .ca_id = 0x1d, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | FLC | FRC },
+	{ .ca_id = 0x1e, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | FLC | FRC },
+	{ .ca_id = 0x1f, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | FLC | FRC },
+};
+
+static void xlnx_dp_hpd_pulse_work_func(struct work_struct *work);
+static int xlnx_dp_txconnected(struct xlnx_dp *dp);
+
+static inline struct xlnx_dp *encoder_to_dp(struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct xlnx_dp, encoder);
+}
+
+static inline struct xlnx_dp *connector_to_dp(struct drm_connector *connector)
+{
+	return container_of(connector, struct xlnx_dp, connector);
+}
+
+static void xlnx_dp_write(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static u32 xlnx_dp_read(void __iomem *base, int offset)
+{
+	return readl(base + offset);
+}
+
+static void xlnx_dp_set(void __iomem *base, int offset, u32 set)
+{
+	xlnx_dp_write(base, offset, xlnx_dp_read(base, offset) | set);
+}
+
+static void xlnx_dp_clr(void __iomem *base, int offset, u32 clr)
+{
+	xlnx_dp_write(base, offset, xlnx_dp_read(base, offset) & ~clr);
+}
+
+static void xlnx_dp_vtc_set_timing(struct xlnx_dp *dp,
+				   struct drm_display_mode *mode)
+{
+	u32 reg;
+	u32 htotal, hactive, hsync_start, hbackporch_start;
+	u32 vtotal, vactive, vsync_start, vbackporch_start;
+	u32 hsync_len, hfront_porch, hback_porch;
+	u32 vsync_len, vfront_porch, vback_porch;
+
+	/*
+	 * TODO : For now driver does not support interlace mode
+	 * In future  driver may add interlace support
+	 */
+
+	/*
+	 * Note that pixels-per-clock for video data and timing is non-existent
+	 * in the Video Timing Controller. There is only a single set of timing
+	 * signals for the video data bus. This means that horizontal (acive
+	 * pixles, hsync, hblank) timing settings can be detected and generated
+	 * only for a multiple of the pixels-per-clock configured in the system.
+	 */
+	hactive = mode->hdisplay / dp->config.ppc;
+	hfront_porch = (mode->hsync_start - mode->hdisplay) / dp->config.ppc;
+	hback_porch = (mode->htotal - mode->hsync_end) / dp->config.ppc;
+	hsync_len = (mode->hsync_end - mode->hsync_start) / dp->config.ppc;
+	htotal = hactive + hfront_porch + hsync_len + hback_porch;
+	hsync_start = hactive + hfront_porch;
+	hbackporch_start = hsync_start + hsync_len;
+
+	vactive = mode->vdisplay;
+	vfront_porch = mode->vsync_start - mode->vdisplay;
+	vback_porch = mode->vtotal - mode->vsync_end;
+	vsync_len = mode->vsync_end - mode->vsync_start;
+	vtotal = vactive + vfront_porch + vsync_len + vback_porch;
+	vsync_start = vactive + vfront_porch;
+	vbackporch_start = vsync_start + vsync_len;
+
+	reg = htotal & XDPTX_VTC_GHSIZE_FRAME_HSIZE;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GHSIZE, reg);
+
+	reg = vtotal & XDPTX_VTC_GVSIZE_FRAME_VSIZE;
+	reg |= reg << XDPTX_VTC_FIELD1_VSIZE_SHIFT;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GVSIZE, reg);
+
+	reg = hactive & XDPTX_VTC_ACTIVE_SIZE_MASK;
+	reg |= (vactive & XDPTX_VTC_ACTIVE_SIZE_MASK) <<
+		XDPTX_VTC_FIELD1_VSIZE_SHIFT;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GASIZE_F0, reg);
+
+	reg = hsync_start & XDPTX_VTC_GHSYNC_START_MASK;
+	reg |= (hbackporch_start << XDPTX_VTC_GH1BPSTART_SHIFT) &
+		XDPTX_VTC_GHSYNC_END_MASK;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GHSYNC, reg);
+
+	reg = vsync_start & XDPTX_VTC_F0_VSYNC_VSTART_MASK;
+	reg |= (vbackporch_start << XDPTX_VTC_FIELD1_VSIZE_SHIFT) &
+		XDPTX_VTC_F0_VSYNC_VEND_MASK;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GVSYNC, reg);
+	xlnx_dp_clr(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GFENC,
+		    XDPTX_VTC_GFENC_MASK);
+
+	/* Calculate and update Generator VBlank Hori field 0 */
+	reg = hactive & XDPTX_VTC_F0VBLANK_HSTART_MASK;
+	reg |= (hactive << XDPTX_VTC_F0VSYNC_HEND_SHIFT) &
+		XDPTX_VTC_F0VBLANK_HEND_MASK;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GVBHOFF, reg);
+
+	/* Calculate and update Generator VSync Hori field 0 */
+	reg = hsync_start & XDPTX_VTC_F0VBLANK_HSTART_MASK;
+	reg |= (hsync_start << XDPTX_VTC_F0VSYNC_HEND_SHIFT) &
+		XDPTX_VTC_F0VBLANK_HEND_MASK;
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GVSHOFF, reg);
+
+	/* sets all polarities as active high */
+	xlnx_dp_write(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_GPOL,
+		      XDPTX_VTC_GPOL_MASK);
+
+	/* configure timing source */
+	xlnx_dp_set(dp->dp_base,
+		    XDPTX_VTC_BASE + XDPTX_VTC_CTL, XDPTX_VTC_CTL_MASK);
+	xlnx_dp_set(dp->dp_base,
+		    XDPTX_VTC_BASE + XDPTX_VTC_CTL, XDPTX_VTC_CTL_RU);
+}
+
+/**
+ * xlnx_dp_update_bpp - Update the current bpp config
+ * @dp: DisplayPort IP core structure
+ *
+ * Update the current bpp based on the color format: bpc & num_colors.
+ * Any function that changes bpc or num_colors should call this
+ * to keep the bpp value in sync.
+ */
+static void xlnx_dp_update_bpp(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_config *config = &dp->config;
+
+	config->bpp = dp->config.bpc * dp->config.num_colors;
+}
+
+/**
+ * xlnx_dp_set_color - Set the color format
+ * @dp: DisplayPort IP core structure
+ * @drm_fourcc: Color string, from xlnx_disp_color_enum
+ *
+ * This function updates misc register values based on color string.
+ */
+static void xlnx_dp_set_color(struct xlnx_dp *dp, u32 drm_fourcc)
+{
+	struct xlnx_dp_config *config = &dp->config;
+
+	config->misc0 &= ~XDPTX_MISC0_FORMAT_MASK;
+
+	switch (drm_fourcc) {
+	case DRM_FORMAT_XBGR8888:
+		fallthrough;
+	case DRM_FORMAT_XRGB8888:
+		fallthrough;
+	case DRM_FORMAT_BGR888:
+		fallthrough;
+	case DRM_FORMAT_RGB888:
+		fallthrough;
+	case DRM_FORMAT_XBGR2101010:
+		config->misc0 |= XDPTX_MISC0_RGB_MASK;
+		config->num_colors = 3;
+		config->fmt = 0x0;
+		break;
+	case DRM_FORMAT_VUY888:
+		fallthrough;
+	case DRM_FORMAT_XVUY8888:
+		fallthrough;
+	case DRM_FORMAT_Y8:
+		fallthrough;
+	case DRM_FORMAT_XVUY2101010:
+		fallthrough;
+	case DRM_FORMAT_Y10:
+		config->misc0 |= XDPTX_MISC0_YCRCB444_MASK;
+		config->num_colors = 3;
+		config->fmt = 0x1;
+		break;
+	case DRM_FORMAT_YUYV:
+		fallthrough;
+	case DRM_FORMAT_UYVY:
+		fallthrough;
+	case DRM_FORMAT_NV16:
+		fallthrough;
+	case DRM_FORMAT_XV20:
+		config->misc0 |= XDPTX_MISC0_YCRCB422_MASK;
+		config->num_colors = 2;
+		config->fmt = 0x2;
+		break;
+	default:
+		dev_dbg(dp->dev, "Warning: Unknown drm_fourcc format :%d\n",
+			drm_fourcc);
+		config->misc0 |= XDPTX_MISC0_RGB_MASK;
+	}
+	xlnx_dp_update_bpp(dp);
+}
+
+/**
+ * xlnx_dp_init_phy - Initialize the phy
+ * @dp: DisplayPort IP core structure
+ *
+ * Initialize the phy.
+ *
+ * Return: 0 if the phy instances are initialized correctly, or the error code
+ * returned from the callee functions.
+ */
+static int xlnx_dp_init_phy(struct xlnx_dp *dp)
+{
+	unsigned int i;
+	int ret;
+
+	xlnx_dp_clr(dp->dp_base, XDPTX_PHYCONFIG_REG,
+		    XDPTX_PHYCONFIG_ALLRESET_MASK);
+
+	for (i = 0; i < XDPTX_MAX_LANES; i++) {
+		ret = phy_init(dp->phy[i]);
+		if (ret) {
+			dev_err(dp->dev,
+				"failed to init phy lane %d\n", i);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+/**
+ * xlnx_dp_exit_phy - Exit the phy
+ * @dp: DisplayPort IP core structure
+ *
+ * Exit the phy.
+ */
+static void xlnx_dp_exit_phy(struct xlnx_dp *dp)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < XDPTX_MAX_LANES; i++) {
+		ret = phy_exit(dp->phy[i]);
+		if (ret)
+			dev_err(dp->dev, "fail to exit phy(%d) %d\n", i, ret);
+		dp->phy[i] = NULL;
+	}
+}
+
+/**
+ * xlnx_dp_phy_ready - check if PHY is ready
+ * @dp: DisplayPort IP core structure
+ *
+ * check if PHY is ready. If PHY is not ready, wait 1ms to check for 100 times.
+ * This amount of delay was suggested by IP designer.
+ *
+ * Return: 0 if PHY is ready, or -ENODEV if PHY is not ready.
+ */
+static int xlnx_dp_phy_ready(struct xlnx_dp *dp)
+{
+	u32 i, reg, ready;
+
+	ready = (1 << XDPTX_MAX_LANES) - 1;
+	ready |= XDPTX_PHYSTATUS_FPGAPLLLOCK_MASK;
+
+	/* Wait for 100ms. This should be enough time for PHY to be ready */
+	for (i = 0; ; i++) {
+		reg = xlnx_dp_read(dp->dp_base, XDPTX_PHYSTATUS_REG);
+		if ((reg & ready) == ready)
+			return 0;
+		if (i == 100) {
+			dev_err(dp->dev, "PHY isn't ready\n");
+			return -ENODEV;
+		}
+		usleep_range(1000, 1100);
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dp_tx_set_vswing_preemp - This function sets current voltage swing and
+ * pre-emphasis level settings from the link_config structure to hardware.
+ * @dp: DisplayPort IP core structure
+ * @aux_data: Aux_data is a pointer to the array used for preparing a burst
+ * write over the AUX channel.
+ */
+static void xlnx_dp_tx_set_vswing_preemp(struct xlnx_dp *dp, u8 *aux_data)
+{
+	static const u32 tx_pe_levels[] = { 0x00, 0x0e, 0x14, 0x1b };
+	static const u8 tx_vs_levels[] = { 0x2, 0x5, 0x8, 0xf };
+	u32 pe_level, vs_level;
+	u8 data, i;
+
+	u8 vs_level_rx = dp->tx_link_config.vs_level;
+	u8 pe_level_rx = dp->tx_link_config.pe_level;
+
+	pe_level = tx_pe_levels[pe_level_rx];
+	vs_level = tx_vs_levels[vs_level_rx];
+
+	/*
+	 * Redriver in path requires different voltage-swing and pre-emphasis
+	 * values. Below case assumes there is no redriver in the path so
+	 * voltage-swing compensation offset is used when pre-emphasis is used.
+	 * See the VESA DisplayPort v1.4 Specification, section 3.6.1.1.
+	 */
+	if (!pe_level_rx)
+		vs_level += XDPTX_VS_LEVEL_OFFSET;
+
+	data = (pe_level_rx << XDP_TRAIN_PRE_EMPHASIS_SHIFT) |
+		vs_level_rx;
+
+	if (vs_level_rx == XDPTX_VS_PE_LEVEL_MAXCOUNT)
+		data |= XDP_TRAIN_MAX_SWING_REACHED;
+	if (pe_level_rx == XDPTX_VS_PE_LEVEL_MAXCOUNT)
+		data |= XDP_DPCD_TRAINING_LANEX_SET_MAX_PE_MASK;
+
+	memset(aux_data, data, XDPTX_MAX_LANES);
+
+	for (i = 0; i < dp->mode.lane_cnt; i++) {
+		xlnx_dp_write(dp->dp_base,
+			      XDPTX_PHYPRECURSOR_LANE0_REG + 4 * i, 0x0);
+		xlnx_dp_write(dp->dp_base,
+			      XDPTX_PHYVOLTAGE_DIFFLANE0_REG + 4 * i, vs_level);
+		xlnx_dp_write(dp->dp_base,
+			      XDPTX_PHYPOSTCURSOR_LANE0_REG + 4 * i, pe_level);
+	}
+}
+
+static int config_gt_control_linerate(struct xlnx_dp *dp, int bw_code)
+{
+	u32 data, regval;
+
+	switch (bw_code) {
+	case DP_LINK_BW_1_62:
+		data = XDPTX_GTCTL_LINE_RATE_162G;
+		break;
+	case DP_LINK_BW_2_7:
+		data = XDPTX_GTCTL_LINE_RATE_270G;
+		break;
+	case DP_LINK_BW_5_4:
+		data = XDPTX_GTCTL_LINE_RATE_540G;
+		break;
+	case DP_LINK_BW_8_1:
+		data = XDPTX_GTCTL_LINE_RATE_810G;
+		break;
+	default:
+		data = XDPTX_GTCTL_LINE_RATE_810G;
+	}
+
+	regval = xlnx_dp_read(dp->dp_base, XDPTX_GTCTL_REG);
+	regval &= ~XDPTX_GTCTL_LINE_RATE_MASK;
+	regval |= FIELD_PREP(XDPTX_GTCTL_LINE_RATE_MASK, data);
+	xlnx_dp_write(dp->dp_base, XDPTX_GTCTL_REG, regval);
+
+	/* Wait for PHY ready */
+	return xlnx_dp_phy_ready(dp);
+}
+
+static int xlnx_dp_tx_gt_control_init(struct xlnx_dp *dp)
+{
+	u32 data;
+	int ret;
+
+	/* Setting initial vswing */
+	data = xlnx_dp_read(dp->dp_base, XDPTX_GTCTL_REG);
+	data &= ~XDPTX_GTCTL_VSWING_MASK;
+	data |= FIELD_PREP(XDPTX_GTCTL_VSWING_MASK, 0x05);
+	xlnx_dp_write(dp->dp_base, XDPTX_GTCTL_REG, data);
+
+	xlnx_dp_clr(dp->dp_base, XDPTX_GTCTL_REG, 0x01);
+	ret = xlnx_dp_phy_ready(dp);
+	if (ret < 0)
+		return ret;
+
+	/* Setting initial link rate */
+	ret = config_gt_control_linerate(dp, DP_LINK_BW_5_4);
+	if (ret) {
+		dev_err(dp->dev, "Default Line Rate setting Failed\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dp_set_train_patttern - This function sets the training pattern to be
+ * used during link training for both the DisplayPort TX core and Rx core.
+ * @dp: DisplayPort IP core structure
+ * @pattern: pattern selects the pattern to be used. One of the following
+ *	- DP_TRAINING_PATTERN_DISABLE
+ *	- DP_TRAINING_PATTERN_1
+ *	- DP_TRAINING_PATTERN_2
+ *	- DP_TRAINING_PATTERN_3
+ *	- DP_TRAINING_PATTERN_4
+ *
+ * Returns:
+ *	- 0 on success or negative error code on failure
+ */
+static int xlnx_dp_set_train_patttern(struct xlnx_dp *dp, u32 pattern)
+{
+	int ret;
+	u8 aux_data[5];
+
+	xlnx_dp_write(dp->dp_base, XDPTX_TRNGPAT_SET_REG, pattern);
+	aux_data[0] = pattern;
+
+	/* write scrambler disable to DisplayPort TX core */
+	switch (pattern) {
+	case DP_TRAINING_PATTERN_DISABLE:
+		xlnx_dp_write(dp->dp_base, XDPTX_SCRAMBLING_DIS_REG, 0);
+		break;
+	case DP_TRAINING_PATTERN_1:
+	case DP_TRAINING_PATTERN_2:
+	case DP_TRAINING_PATTERN_3:
+		aux_data[0] |= DP_LINK_SCRAMBLING_DISABLE;
+		xlnx_dp_write(dp->dp_base, XDPTX_SCRAMBLING_DIS_REG, 1);
+		break;
+	case DP_TRAINING_PATTERN_4:
+		xlnx_dp_write(dp->dp_base, XDPTX_SCRAMBLING_DIS_REG, 0);
+		break;
+	default:
+		break;
+	}
+
+	/* Make the adjustment to both the DisplayPort TX core and the RX */
+	xlnx_dp_tx_set_vswing_preemp(dp, &aux_data[1]);
+
+	if (pattern == DP_TRAINING_PATTERN_DISABLE)
+		ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_PATTERN_SET,
+					aux_data, 1);
+	else
+		ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_PATTERN_SET,
+					aux_data, 5);
+
+	return ret;
+}
+
+/**
+ * xlnx_dp_tx_pe_vs_adjust_handler - Calculate and configure pe and vs values
+ * @dp: DisplayPort IP core structure
+ * @dp_phy_opts: phy configuration structure
+ *
+ * This function adjusts the pre emphasis and voltage swing values of phy.
+ */
+static void xlnx_dp_tx_pe_vs_adjust_handler(struct xlnx_dp *dp,
+					    struct phy_configure_opts_dp *dp_phy_opts)
+{
+	u8 preemp = 0, diff_swing = 0;
+	u32 data;
+
+	switch (dp_phy_opts->pre[0]) {
+	case 0:
+		preemp = XVPHY_GTHE4_PREEMP_DP_L0;
+		break;
+	case 1:
+		preemp = XVPHY_GTHE4_PREEMP_DP_L1;
+		break;
+	case 2:
+		preemp = XVPHY_GTHE4_PREEMP_DP_L2;
+		break;
+	case 3:
+		preemp = XVPHY_GTHE4_PREEMP_DP_L3;
+		break;
+	}
+
+	switch (dp_phy_opts->voltage[0]) {
+	case 0:
+		switch (dp_phy_opts->pre[0]) {
+		case 0:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V0P0;
+			break;
+		case 1:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V0P1;
+			break;
+		case 2:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V0P2;
+			break;
+		case 3:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V0P3;
+			break;
+		}
+		break;
+	case 1:
+		switch (dp_phy_opts->pre[0]) {
+		case 0:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V1P0;
+			break;
+		case 1:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V1P1;
+			break;
+		case 2:
+			fallthrough;
+		case 3:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V1P2;
+			break;
+		}
+		break;
+	case 2:
+		switch (dp_phy_opts->pre[0]) {
+		case 0:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V2P0;
+			break;
+		case 1:
+			fallthrough;
+		case 2:
+			fallthrough;
+		case 3:
+			diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V2P1;
+			break;
+		}
+		break;
+	case 3:
+		diff_swing = XVPHY_GTHE4_DIFF_SWING_DP_V3P0;
+		break;
+	}
+
+	data = xlnx_dp_read(dp->dp_base, XDPTX_GTCTL_REG);
+	data &= ~(XDPTX_GTCTL_POST_CUR_MASK | XDPTX_GTCTL_VSWING_MASK);
+	data |= FIELD_PREP(XDPTX_GTCTL_VSWING_MASK, diff_swing) |
+		FIELD_PREP(XDPTX_GTCTL_POST_CUR_MASK, preemp);
+	xlnx_dp_write(dp->dp_base, XDPTX_GTCTL_REG, data);
+
+	dp_phy_opts->set_voltages = 0;
+}
+
+/**
+ * xlnx_dp_tx_adj_vswing_preemp - Sets voltage swing and pre-emphasis levels
+ * using the adjustment requests obtained from the RX device
+ * @dp:Pointer to xlnx_dp structure
+ * @link_status: An array of link status register
+ *
+ * This function sets new voltage swing and pre-emphasis levels using the
+ * adjustment requests obtained from the sink.
+ *
+ * Return: 0 if the new levels were written successfully.
+ * error value on failure.
+ */
+static int xlnx_dp_tx_adj_vswing_preemp(struct xlnx_dp *dp, u8 link_status[6])
+{
+	struct phy_configure_opts_dp *phy_cfg = &dp->phy_opts.dp;
+	int ret;
+	u8 i, aux_data[4];
+	u8 vs_level_adj_req[4];
+	u8 pe_level_adj_req[4];
+	u8 max_lanes = dp->link_config.max_lanes;
+
+	/*
+	 * Analyze the adjustment requests for changes in voltage swing and
+	 * pre-emphasis levels.
+	 */
+	vs_level_adj_req[0] = FIELD_GET(DP_ADJUST_VOLTAGE_SWING_LANE0_MASK,
+					link_status[4]);
+	vs_level_adj_req[1] = FIELD_GET(DP_ADJUST_VOLTAGE_SWING_LANE1_MASK,
+					link_status[4]);
+	vs_level_adj_req[2] = FIELD_GET(DP_ADJUST_VOLTAGE_SWING_LANE0_MASK,
+					link_status[5]);
+	vs_level_adj_req[3] = FIELD_GET(DP_ADJUST_VOLTAGE_SWING_LANE1_MASK,
+					link_status[5]);
+	pe_level_adj_req[0] = FIELD_GET(DP_ADJUST_PRE_EMPHASIS_LANE0_MASK,
+					link_status[4]);
+	pe_level_adj_req[1] = FIELD_GET(DP_ADJUST_PRE_EMPHASIS_LANE1_MASK,
+					link_status[4]);
+	pe_level_adj_req[2] = FIELD_GET(DP_ADJUST_PRE_EMPHASIS_LANE0_MASK,
+					link_status[5]);
+	pe_level_adj_req[3] = FIELD_GET(DP_ADJUST_PRE_EMPHASIS_LANE1_MASK,
+					link_status[5]);
+
+	/*
+	 * change the drive settings to match the adjustment requests. Use the
+	 * greatest level requested.
+	 */
+	dp->tx_link_config.vs_level = 0;
+	dp->tx_link_config.pe_level = 0;
+	for (i = 0; i < dp->mode.lane_cnt ; i++) {
+		if (vs_level_adj_req[i] > dp->tx_link_config.vs_level)
+			dp->tx_link_config.vs_level = vs_level_adj_req[i];
+		if (pe_level_adj_req[i] > dp->tx_link_config.pe_level)
+			dp->tx_link_config.pe_level = pe_level_adj_req[i];
+	}
+
+	/*
+	 * Verify that the voltage swing and pre-emphasis combination is
+	 * allowed. Some combinations will result in differential peak-to-peak
+	 * voltage that is outside the permissible range. See the VESA
+	 * DisplayPort v1.4 Specification, section 3.1.5.2.
+	 * The valid combinations are:
+	 *      PE=0    PE=1    PE=2    PE=3
+	 * VS=0 Valid   Valid   Valid   Valid
+	 * VS=1 Valid   Valid   Valid
+	 * VS=2 Valid   Valid
+	 * VS=3 Valid
+	 */
+	if (dp->tx_link_config.pe_level > (4 - dp->tx_link_config.vs_level))
+		dp->tx_link_config.pe_level = 4 - dp->tx_link_config.vs_level;
+
+	/*
+	 * Make the adjustments to both the DisplayPort TX core and the RX
+	 * device.
+	 */
+	xlnx_dp_tx_set_vswing_preemp(dp, aux_data);
+	/*
+	 * Write the voltage swing and pre-emphasis levels for each lane to the
+	 * RX device.
+	 */
+	ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET,
+				&aux_data[0], 4);
+	if (ret < 0)
+		return ret;
+
+	phy_cfg->lanes = max_lanes;
+	phy_cfg->pre[0] = dp->tx_link_config.pe_level;
+	phy_cfg->voltage[0] = dp->tx_link_config.vs_level;
+	phy_cfg->set_voltages = 1;
+
+	if (!dp->config.versal_gt_present)
+		phy_configure(dp->phy[0], &dp->phy_opts);
+	else
+		xlnx_dp_tx_pe_vs_adjust_handler(dp, &dp->phy_opts.dp);
+
+	return 0;
+}
+
+/**
+ * xlnx_dp_check_clock_recovery - This function checks if the RX device's DPCD
+ * indicates that the clock recovery sequence during link training was
+ * successful - the RX device's link clock and data recovery unit has realized
+ * and maintained the frequency lock for all the lanes currently in use.
+ * @dp: DisplayPort IP core structure
+ * @lane_cnt: Number of lanes in use
+ *
+ * Return: 0 if the RX device's clock recovery PLL has achieved frequency lock
+ * for all the lanes in use.Othewise returns error value.
+ */
+static int xlnx_dp_check_clock_recovery(struct xlnx_dp *dp, u8 lane_cnt)
+{
+	struct xlnx_dp_link_config *link_config = &dp->link_config;
+	int ret;
+	u8 link_status[DP_LINK_STATUS_SIZE];
+
+	ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+	if (ret < 0)
+		return ret;
+
+	switch (lane_cnt) {
+	case XDPTX_DP_LANE_COUNT_4:
+		if (!(link_status[0] & XDPTX_DPCD_LANE02_CRDONE_MASK)) {
+			link_config->cr_done_cnt = XDPTX_LANE0_CRDONE_MASK;
+			return 1;
+		}
+		if (!(link_status[0] & XDPTX_DPCD_LANE13_CRDONE_MASK)) {
+			link_config->cr_done_cnt = XDPTX_LANE1_CRDONE_MASK;
+			return 1;
+		}
+		if (!(link_status[1] & XDPTX_DPCD_LANE02_CRDONE_MASK)) {
+			link_config->cr_done_cnt = XDPTX_LANE2_CRDONE_MASK;
+			return 1;
+		}
+		if (!(link_status[1] & XDPTX_DPCD_LANE13_CRDONE_MASK)) {
+			link_config->cr_done_cnt = XDPTX_LANE3_CRDONE_MASK;
+			return 1;
+		}
+		link_config->cr_done_cnt = 0x4;
+		fallthrough;
+	case XDPTX_DP_LANE_COUNT_2:
+		if (!(link_status[0] & XDPTX_DPCD_LANE02_CRDONE_MASK)) {
+			link_config->cr_done_cnt = 0x0;
+			return 1;
+		}
+		if (!(link_status[0] & XDPTX_DPCD_LANE13_CRDONE_MASK)) {
+			link_config->cr_done_cnt = 0x1;
+			return 1;
+		}
+		link_config->cr_done_cnt = 0x2;
+		fallthrough;
+	case XDPTX_DP_LANE_COUNT_1:
+		if (!(link_status[0] & XDPTX_DPCD_LANE02_CRDONE_MASK)) {
+			link_config->cr_done_cnt = 0x0;
+			return 1;
+		}
+		link_config->cr_done_cnt = 0x1;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+static int xlnx_dp_set_linkrate(struct xlnx_dp *dp, u8 bw_code)
+{
+	struct phy_configure_opts_dp *phy_cfg = &dp->phy_opts.dp;
+	int ret;
+	u32 reg, lrate_val = 0, val;
+	u8 lane_count = dp->mode.lane_cnt;
+
+	if (!xlnx_dp_txconnected(dp)) {
+		dev_dbg(dp->dev, "display is not connected");
+		return connector_status_disconnected;
+	}
+
+	dp->mode.bw_code = bw_code;
+
+	switch (bw_code) {
+	case DP_LINK_BW_1_62:
+		reg = XDPTX_PHYCLOCK_FBSETTING162_MASK;
+		phy_cfg->link_rate = XDPTX_REDUCED_BIT_RATE / 100;
+		if (dp->config.versal_gt_present)
+			lrate_val = XDPTX_GTCTL_LINE_RATE_162G;
+		break;
+	case DP_LINK_BW_2_7:
+		reg = XDPTX_PHYCLOCK_FBSETTING270_MASK;
+		phy_cfg->link_rate = XDPTX_HIGH_BIT_RATE_1 / 100;
+		if (dp->config.versal_gt_present)
+			lrate_val = XDPTX_GTCTL_LINE_RATE_270G;
+		break;
+	case DP_LINK_BW_5_4:
+		reg = XDPTX_PHYCLOCK_FBSETTING810_MASK;
+		phy_cfg->link_rate = XDPTX_HIGH_BIT_RATE_2 / 100;
+		if (dp->config.versal_gt_present)
+			lrate_val = XDPTX_GTCTL_LINE_RATE_540G;
+		break;
+	case DP_LINK_BW_8_1:
+		reg = XDPTX_PHYCLOCK_FBSETTING810_MASK;
+		phy_cfg->link_rate = XDPTX_HIGH_BIT_RATE_3 / 100;
+		if (dp->config.versal_gt_present)
+			lrate_val = XDPTX_GTCTL_LINE_RATE_810G;
+		break;
+	default:
+		reg = XDPTX_PHYCLOCK_FBSETTING810_MASK;
+		phy_cfg->link_rate = XDPTX_HIGH_BIT_RATE_3 / 100;
+		if (dp->config.versal_gt_present)
+			lrate_val = XDPTX_GTCTL_LINE_RATE_810G;
+	}
+
+	/*
+	 * set the clock frequency for the DisplayPort PHY corresponding
+	 * to a desired link rate
+	 */
+	val = xlnx_dp_read(dp->dp_base, XDPTX_ENABLE_REG);
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 0);
+	xlnx_dp_write(dp->dp_base, XDPTX_PHYCLOCK_FBSETTING_REG, reg);
+	if (val)
+		xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 1);
+	/* Wait for PHY ready */
+	ret = xlnx_dp_phy_ready(dp);
+	if (ret < 0)
+		return ret;
+
+	/* write new link rate to the DisplayPort TX core */
+	xlnx_dp_write(dp->dp_base, XDPTX_LINKBW_SET_REG, bw_code);
+	/* write new link rate to the RX device */
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_LINK_BW_SET, bw_code);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set DP bandwidth\n");
+		return ret;
+	}
+	/* configure video phy controller to new link rate */
+	phy_cfg->set_rate = 1;
+	phy_cfg->lanes = lane_count;
+	if (!dp->config.versal_gt_present)
+		phy_configure(dp->phy[0], &dp->phy_opts);
+
+	if (dp->config.versal_gt_present) {
+		val = xlnx_dp_read(dp->dp_base, XDPTX_GTCTL_REG);
+		val &= ~XDPTX_GTCTL_LINE_RATE_MASK;
+		val |= FIELD_PREP(XDPTX_GTCTL_LINE_RATE_MASK, lrate_val);
+		xlnx_dp_write(dp->dp_base, XDPTX_GTCTL_REG, val);
+	}
+
+	return 0;
+}
+
+static int xlnx_dp_set_lanecount(struct xlnx_dp *dp, u8 lane_cnt)
+{
+	int ret;
+	u8 data;
+
+	dp->mode.lane_cnt = lane_cnt;
+	xlnx_dp_write(dp->dp_base, XDPTX_LANECNT_SET_REG, lane_cnt);
+
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data);
+	if (ret < 0) {
+		dev_err(dp->dev, "DPCD read retry fails");
+		return ret;
+	}
+
+	data &= ~XDPTX_DPCD_LANECNT_SET_MASK;
+	data |= dp->mode.lane_cnt;
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, data);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set lane count\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dp_check_link_status - This function checks if the receiver has
+ * achieved and maintained clock recovery, channel equalization, symbol lock, and
+ * interlane alignment for all lanes currently in use
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: 0 if link status is successfully.
+ * error value on failure.
+ */
+static int xlnx_dp_check_link_status(struct xlnx_dp *dp)
+{
+	int ret;
+	u8 link_status[DP_LINK_STATUS_SIZE];
+	u8 retry = 0;
+
+	memset(link_status, 0, sizeof(link_status));
+
+	if (!xlnx_dp_txconnected(dp)) {
+		dev_dbg(dp->dev, "display is not connected");
+		return connector_status_disconnected;
+	}
+
+	for (retry = 0; retry < 5; retry++) {
+		ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+		if (ret < 0)
+			return ret;
+
+		if (drm_dp_clock_recovery_ok(link_status, dp->mode.lane_cnt) ||
+		    drm_dp_channel_eq_ok(link_status, dp->mode.lane_cnt))
+			return 0;
+	}
+
+	return -EINVAL;
+}
+
+static int xlnx_dp_post_training(struct xlnx_dp *dp)
+{
+	int ret;
+	u8 data;
+
+	if (dp->dpcd[DP_DPCD_REV] == XDPTX_V1_4) {
+		ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data);
+		if (ret < 0) {
+			dev_dbg(dp->dev, "DPCD read first try fails");
+			ret = drm_dp_dpcd_readb(&dp->aux,
+						DP_LANE_COUNT_SET, &data);
+			if (ret < 0) {
+				dev_err(dp->dev, "DPCD read retry fails");
+				return ret;
+			}
+		}
+
+		/*
+		 * Post Link Training ; An upstream device with a DPTX sets
+		 * this bit to 1 to grant the POST_LT_ADJ_REQ sequence by the
+		 * downstream DPRX if the downstream DPRX supports
+		 * POST_LT_ADJ_REQ
+		 */
+		data |= 0x20;
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, data);
+		if (ret < 0) {
+			dev_dbg(dp->dev, "DPCD write first try fails");
+			ret = drm_dp_dpcd_writeb(&dp->aux,
+						 DP_LANE_COUNT_SET, data);
+			if (ret < 0) {
+				dev_err(dp->dev, "DPCD write retry fails");
+				return ret;
+			}
+		}
+	}
+
+	ret = xlnx_dp_check_link_status(dp);
+	if (ret < 0)
+		return ret;
+
+	ret = xlnx_dp_set_train_patttern(dp, DP_TRAINING_PATTERN_DISABLE);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to disable training pattern\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dp_link_train_cr - Train clock recovery
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: 0 if clock recovery train is done successfully, or corresponding
+ * error code.
+ */
+static int xlnx_dp_link_train_cr(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_tx_link_config *link_config = &dp->tx_link_config;
+	struct xlnx_dp_link_config *config = &dp->link_config;
+	int ret;
+	u16 max_tries;
+	u8 prev_vs_level = 0, same_vs_level_count = 0;
+	u8 link_status[DP_LINK_STATUS_SIZE];
+	u8 lane_cnt = dp->mode.lane_cnt;
+	bool cr_done = 0;
+
+	/* start from minimal vs and pe levels */
+	dp->tx_link_config.vs_level = 0;
+	dp->tx_link_config.pe_level = 0;
+
+	ret = xlnx_dp_set_train_patttern(dp, DP_TRAINING_PATTERN_1);
+	if (ret < 0)
+		return XLNX_DP_TRAIN_FAILURE;
+
+	/*
+	 * 256 loops should be maximum iterations for 4 lanes and 4 values.
+	 * So, This loop should exit before 512 iterations
+	 */
+	for (max_tries = 0; max_tries < 512; max_tries++) {
+		/*
+		 * Obtain the required delay for clock recovery as specified
+		 * by the RX device.
+		 * Wait delay specified in TRAINING_AUX_RD_INTERVAL(0x0E)
+		 */
+		drm_dp_link_train_clock_recovery_delay(&dp->aux, dp->dpcd);
+		/*
+		 * check if all lanes have realized and maintained the
+		 * frequency lock and get adjustment requests.
+		 */
+		ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+		if (ret < 0)
+			return XLNX_DP_TRAIN_FAILURE;
+
+		cr_done = xlnx_dp_check_clock_recovery(dp, lane_cnt);
+		if (!cr_done)
+			return XLNX_DP_TRAIN_CE;
+		/*
+		 * check if the same voltage swing for each lane has been
+		 * used 5 consecutive times.
+		 */
+		if (prev_vs_level == link_config->vs_level) {
+			same_vs_level_count++;
+		} else {
+			same_vs_level_count = 0;
+			prev_vs_level = link_config->vs_level;
+		}
+
+		if (same_vs_level_count >= XDPTX_VS_LEVEL_MAXCOUNT)
+			break;
+
+		if (link_config->vs_level == XDPTX_VS_PE_LEVEL_MAXCOUNT)
+			break;
+		/* Adjust the drive settings as requested by the RX device */
+		ret = xlnx_dp_tx_adj_vswing_preemp(dp, link_status);
+		if (ret < 0)
+			return XLNX_DP_TRAIN_FAILURE;
+	}
+
+	if (dp->mode.bw_code == DP_LINK_BW_1_62) {
+		if (config->cr_done_cnt != 0x4 && config->cr_done_cnt != 0x0) {
+			ret = xlnx_dp_set_train_patttern(dp, DP_TRAINING_PATTERN_DISABLE);
+			if (ret < 0) {
+				dev_err(dp->dev, "failed to disable training pattern\n");
+				return ret;
+			}
+
+			ret = xlnx_dp_set_linkrate(dp, DP_LINK_BW_8_1);
+			if (ret < 0) {
+				dev_err(dp->dev, "failed to set link rate\n");
+				return ret;
+			}
+
+			ret = xlnx_dp_set_lanecount(dp, config->cr_done_cnt);
+			if (ret < 0) {
+				dev_err(dp->dev, "failed to set lane count\n");
+				return ret;
+			}
+			config->cr_done_oldstate = config->cr_done_cnt;
+
+			return XLNX_DP_TRAIN_CR;
+		}
+	}
+
+	return XLNX_DP_ADJUST_LINKRATE;
+}
+
+/**
+ * xlnx_dp_adjust_linkrate - Adjust the link rate
+ * @dp: DisplayPort core structure
+ *
+ * This function is reached if either the clock recovery or the channel
+ * equalization process failed during training. As a result, the data rate will
+ * be downshifted and training will be re-attempted at the reduced data rate. If
+ * the data rate is already at 1.62 Gbps, a downshited in lane count will be
+ * attempted.
+ *
+ * Return: The next training state:
+ *	- XLNX_DP_ADJUST_LANECOUNT if the minimal data rate is already in use.
+ *	re-attempt training at a reduced lane count.
+ *	- XLNX_DP_TRAIN_CR otherwise. Re-attempt training.
+ */
+static int xlnx_dp_adjust_linkrate(struct xlnx_dp *dp)
+{
+	int ret;
+	u8 bw_code;
+
+	switch (dp->mode.bw_code) {
+	case DP_LINK_BW_8_1:
+		bw_code = DP_LINK_BW_5_4;
+		break;
+	case DP_LINK_BW_5_4:
+		bw_code = DP_LINK_BW_2_7;
+		break;
+	case DP_LINK_BW_2_7:
+		bw_code = DP_LINK_BW_1_62;
+		break;
+	default:
+		/*
+		 * Already at the lowest link rate. Try reducing the lane
+		 * count next
+		 */
+		return XLNX_DP_ADJUST_LANECOUNT;
+	}
+
+	ret = xlnx_dp_set_linkrate(dp, bw_code);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set link rate\n");
+		return XLNX_DP_TRAIN_FAILURE;
+	}
+
+	ret = xlnx_dp_set_lanecount(dp, dp->link_config.cr_done_oldstate);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set lane count\n");
+		return XLNX_DP_TRAIN_FAILURE;
+	}
+
+	return XLNX_DP_TRAIN_CR;
+}
+
+/**
+ * xlnx_dp_adjust_lanecount - Adjust the lane count
+ * @dp: DisplayPort core structure
+ *
+ * This function is reached if either the clock recovery or the channel
+ * equalization process failed during training. As a result, the number of lanes
+ * will be downshifted and training will be re-attempted at this lower lane
+ * count.
+ *
+ * note: Training will be re-attempted with the maximum data rate being used
+ * with the reduced lane count to train the main link at the maximum bandwidth
+ * possible.
+ *
+ * Return: The next training state:
+ *	- XLNX_DP_TRAIN_FAILURE if only one lane is already in use
+ *	- XLNX_DP_TRAIN_CR otherwise. Re-attempt training
+ */
+static int xlnx_dp_adjust_lanecount(struct xlnx_dp *dp)
+{
+	int max_rate = dp->link_config.max_rate, ret;
+	u8 bw_code = drm_dp_link_rate_to_bw_code(max_rate), lane_cnt;
+
+	switch (dp->mode.lane_cnt) {
+	case XDPTX_DP_LANE_COUNT_4:
+		lane_cnt = XDPTX_DP_LANE_COUNT_2;
+		break;
+	case XDPTX_DP_LANE_COUNT_2:
+		lane_cnt = XDPTX_DP_LANE_COUNT_1;
+		break;
+	default:
+		dev_err(dp->dev, " Training failed at lowest linkrate and lane count\n");
+		return XLNX_DP_TRAIN_FAILURE;
+	}
+
+	ret = xlnx_dp_set_linkrate(dp, bw_code);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set link rate\n");
+		return XLNX_DP_TRAIN_FAILURE;
+	}
+
+	ret = xlnx_dp_set_lanecount(dp, lane_cnt);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set lane count\n");
+		return XLNX_DP_TRAIN_FAILURE;
+	}
+
+	return XLNX_DP_TRAIN_CR;
+}
+
+/**
+ * xlnx_dp_link_train_ce - Train channel equalization
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: 0 if channel equalization train is done successfully, or
+ * corresponding error code.
+ */
+
+static int xlnx_dp_link_train_ce(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_link_config *config = &dp->link_config;
+	struct xlnx_dp_mode *mode = &dp->mode;
+	int ret;
+	u32 i;
+	u8 pat, link_status[DP_LINK_STATUS_SIZE];
+	u8 lane_cnt = dp->mode.lane_cnt;
+	bool ce_done, cr_done;
+
+	if (dp->dpcd[DP_DPCD_REV] == XDPTX_V1_4 &&
+	    dp->dpcd[DP_MAX_DOWNSPREAD] & DP_TPS4_SUPPORTED) {
+		pat = DP_TRAINING_PATTERN_4;
+	} else if (dp->dpcd[DP_MAX_LANE_COUNT] & DP_TPS3_SUPPORTED) {
+		pat = DP_TRAINING_PATTERN_3;
+	} else {
+		pat = DP_TRAINING_PATTERN_2;
+	}
+
+	ret = xlnx_dp_set_train_patttern(dp, pat);
+	if (ret < 0)
+		return XLNX_DP_TRAIN_FAILURE;
+
+	for (i = 0; i < DP_MAX_TRAINING_TRIES; i++) {
+		/*
+		 * Obtain the required delay for channel equalization as
+		 * specified by the RX device.
+		 */
+		drm_dp_link_train_channel_eq_delay(&dp->aux, dp->dpcd);
+
+		ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+		if (ret < 0)
+			return XLNX_DP_TRAIN_FAILURE;
+
+		cr_done = drm_dp_clock_recovery_ok(link_status, lane_cnt);
+		if (!cr_done)
+			break;
+		/*
+		 * check if all lanes have accomplished channel equalization,
+		 * symbol lock, and interlane alignment.
+		 */
+		ce_done = drm_dp_channel_eq_ok(link_status, lane_cnt);
+		if (ce_done)
+			return XLNX_DP_TRAIN_SUCCESS;
+
+		ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+		if (ret < 0)
+			return XLNX_DP_TRAIN_FAILURE;
+
+		ret = xlnx_dp_tx_adj_vswing_preemp(dp, link_status);
+		if (ret != 0)
+			return XLNX_DP_TRAIN_FAILURE;
+	}
+	/*
+	 * Tried 5 times with no success. Try a reduced bitrate first, then
+	 * reduce the number of lanes.
+	 */
+
+	if (!cr_done) {
+		/* Down link on CR failure in EQ state */
+		config->cr_done_oldstate = config->max_lanes;
+		return XLNX_DP_ADJUST_LINKRATE;
+	} else if ((mode->lane_cnt == 1) && !ce_done) {
+		/* Need to set lanecount for next iter */
+		mode->lane_cnt = config->max_lanes;
+		config->cr_done_oldstate = config->max_lanes;
+		return XLNX_DP_ADJUST_LINKRATE;
+	} else if ((mode->lane_cnt > 1) && !ce_done) {
+		/* For EQ failure downlink the lane count */
+		return XLNX_DP_ADJUST_LANECOUNT;
+	}
+
+	config->cr_done_oldstate = config->max_lanes;
+
+	return XLNX_DP_ADJUST_LINKRATE;
+}
+
+/**
+ * xlnx_dp_run_training - Run the link training process
+ * @dp: DisplayPort core structure
+ *
+ * This function is implemented as a state machine, with each state returning
+ * the next state. First, the clock recovery sequence will be run; if successful,
+ * the channel equalization sequence will run. If either the clock recovery or
+ * channel equalization sequence failed, the link rate or the number of lanes
+ * used will be reduced and training will be re-attempted. If training fails
+ * at the minimal data rate, 1.62 Gbps with a single lane, training will no
+ * longer re-attempt and fail.
+ *
+ * Return: 0 if the training process succeeded.
+ * error value on training failure.
+ */
+static int xlnx_dp_run_training(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_link_config *config = &dp->link_config;
+	enum xlnx_dp_train_state state = XLNX_DP_TRAIN_CR;
+	int ret;
+
+	while (1) {
+		switch (state) {
+		case XLNX_DP_TRAIN_CR:
+			state = xlnx_dp_link_train_cr(dp);
+			break;
+		case XLNX_DP_TRAIN_CE:
+			state = xlnx_dp_link_train_ce(dp);
+			break;
+		case XLNX_DP_ADJUST_LINKRATE:
+			state = xlnx_dp_adjust_linkrate(dp);
+			break;
+		case XLNX_DP_ADJUST_LANECOUNT:
+			state = xlnx_dp_adjust_lanecount(dp);
+			break;
+		default:
+			break;
+		}
+
+		if (state == XLNX_DP_TRAIN_SUCCESS) {
+			config->cr_done_oldstate = config->max_lanes;
+			config->cr_done_cnt = config->max_lanes;
+			dev_dbg(dp->dev, "dp training is success !!");
+			break;
+		} else if (state == XLNX_DP_TRAIN_FAILURE) {
+			config->cr_done_oldstate = config->max_lanes;
+			config->cr_done_cnt = config->max_lanes;
+			goto err_out;
+		}
+
+		if (state == XLNX_DP_ADJUST_LINKRATE ||
+		    state == XLNX_DP_ADJUST_LANECOUNT) {
+			ret = xlnx_dp_set_train_patttern(dp, DP_TRAINING_PATTERN_DISABLE);
+			if (ret < 0) {
+				dev_err(dp->dev,
+					"failed to disable training pattern\n");
+				goto err_out;
+			}
+		}
+	}
+
+	return 0;
+err_out:
+	dev_err(dp->dev, "failed to train the DP link\n");
+	return -EIO;
+}
+
+static void xlnx_dp_phy_reset(struct xlnx_dp *dp, u32 reset)
+{
+	u32 phy_val, reg_val;
+
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 0);
+
+	/* Preserve the current PHY settings */
+	phy_val = xlnx_dp_read(dp->dp_base, XDPTX_PHYCONFIG_REG);
+
+	/* Apply reset */
+	reg_val = phy_val | reset;
+	xlnx_dp_write(dp->dp_base, XDPTX_PHYCONFIG_REG, reg_val);
+
+	/* Remove reset */
+	xlnx_dp_write(dp->dp_base, XDPTX_PHYCONFIG_REG, phy_val);
+
+	/* Wait for the PHY to be ready */
+	xlnx_dp_phy_ready(dp);
+
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 1);
+}
+
+/**
+ * xlnx_dp_aux_cmd_submit - Submit aux command
+ * @dp: DisplayPort IP core structure
+ * @cmd: aux command
+ * @addr: aux address
+ * @buf: buffer for command data
+ * @bytes: number of bytes for @buf
+ * @reply: reply code to be returned
+ *
+ * Submit an aux command. All aux related commands, native or i2c aux
+ * read/write, are submitted through this function. The function is mapped to
+ * the transfer function of struct drm_dp_aux. This function involves in
+ * multiple register reads/writes, thus synchronization is needed, and it is
+ * done by drm_dp_helper using @hw_mutex. The calling thread goes into sleep
+ * if there's no immediate reply to the command submission. The reply code is
+ * returned at @reply if @reply != NULL.
+ *
+ * Return: 0 if the command is submitted properly, or corresponding error code:
+ * -EBUSY when there is any request already being processed
+ * -ETIMEDOUT when receiving reply is timed out
+ * -EIO when received bytes are less than requested
+ */
+static int xlnx_dp_aux_cmd_submit(struct xlnx_dp *dp, u32 cmd, u16 addr,
+				  u8 *buf, u8 bytes, u8 *reply)
+{
+	bool is_read = (cmd & XDPTX_AUX_READ_BIT) ? true : false;
+	void __iomem *dp_base = dp->dp_base;
+	u32 reg, i;
+
+	reg = xlnx_dp_read(dp_base, XDPTX_INTR_SIGSTATE_REG);
+	if (reg & XDPTX_INTR_SIGREQSTATE)
+		return -EBUSY;
+
+	xlnx_dp_write(dp_base, XDPTX_AUX_ADDR_REG, addr);
+	if (!is_read) {
+		for (i = 0; i < bytes; i++) {
+			xlnx_dp_write(dp_base, XDPTX_AUX_WRITEFIFO_REG,
+				      buf[i]);
+		}
+	}
+
+	reg = cmd << XDPTX_AUXCMD_SHIFT;
+	if (!bytes)
+		reg |= XDPTX_AUXCMD_ADDRONLY_MASK;
+	else
+		reg |= (bytes - 1) << XDPTX_AUXCMD_BYTES_SHIFT;
+	xlnx_dp_write(dp_base, XDPTX_AUXCMD_REG, reg);
+
+	/* Wait for reply to be delivered upto 2ms */
+	for (i = 0; ; i++) {
+		reg = xlnx_dp_read(dp_base, XDPTX_INTR_SIGSTATE_REG);
+		if (reg & XDPTX_INTR_SIGRPLYSTATE)
+			break;
+
+		if (reg & XDPTX_INTR_RPLYTIMEOUT ||
+		    i == 2)
+			return -ETIMEDOUT;
+
+		usleep_range(1000, 1100);
+	}
+
+	reg = xlnx_dp_read(dp_base, XDPTX_AUXREPLY_CODE_REG);
+	if (reply)
+		*reply = reg;
+
+	if (is_read && !reg) {
+		reg = xlnx_dp_read(dp_base, XDPTX_AUXREPLY_DATACNT_REG);
+		if ((reg & XDPTX_AUXREPLY_DATACNT_MASK) != bytes)
+			return -EIO;
+
+		for (i = 0; i < bytes; i++) {
+			buf[i] = xlnx_dp_read(dp_base,
+					      XDPTX_AUXREPLY_DATA_REG);
+		}
+	}
+
+	return 0;
+}
+
+static ssize_t
+xlnx_dp_aux_transfer(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg)
+{
+	struct xlnx_dp *dp = container_of(aux, struct xlnx_dp, aux);
+	int ret;
+	unsigned int i, iter;
+
+	/* This is to iterate at least 50 msec */
+	iter = 50 * 1000 / 400;
+
+	for (i = 0; i < iter; i++) {
+		ret = xlnx_dp_aux_cmd_submit(dp, msg->request, msg->address,
+					     msg->buffer, msg->size,
+					       &msg->reply);
+		if (!ret) {
+			dev_dbg(dp->dev, "aux %d retries\n", i);
+			return msg->size;
+		}
+
+		if (dp->status == connector_status_disconnected) {
+			dev_info(dp->dev, "no connected aux device\n");
+			return -ENODEV;
+		}
+
+		usleep_range(3200, 3300);
+	}
+
+	dev_info(dp->dev, "failed aux transfer\n");
+
+	return ret;
+}
+
+/**
+ * xlnx_dp_init_aux - Initialize the DP aux
+ * @dp: DisplayPort IP core structure
+ *
+ * Initialize the DP aux. The aux clock is derived from the axi clock, so
+ * this function gets the axi clock frequency and calculates the filter
+ * value. Additionally, the interrupts and transmitter are enabled.
+ *
+ * Return: 0 on success, error value otherwise
+ */
+static int xlnx_dp_init_aux(struct xlnx_dp *dp)
+{
+	unsigned long rate;
+	u32 reg, w;
+
+	rate = clk_get_rate(dp->axi_lite_clk);
+	if (rate < XDPTX_CLKDIV_MHZ) {
+		dev_err(dp->dev, "aclk should be higher than 1MHz\n");
+		return -EINVAL;
+	}
+
+	/* Allowable values for this register are: 8, 16, 24, 32, 40, 48 */
+	for (w = 8; w <= 48; w += 8) {
+		/* AUX pulse width should be between 0.4 to 0.6 usec */
+		if (w >= (4 * rate / 10000000) &&
+		    w <= (6 * rate / 10000000))
+			break;
+	}
+
+	if (w > 48)
+		w = 48;
+
+	reg = w << XDPTX_CLKDIV_AUXFILTER_SHIFT;
+	reg |= rate / XDPTX_CLKDIV_MHZ;
+	xlnx_dp_write(dp->dp_base, XDPTX_CLKDIV_REG, reg);
+
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 1);
+	return 0;
+}
+
+/**
+ * xlnx_dp_exit_aux - De-initialize the DP aux
+ * @dp: DisplayPort IP core structure
+ *
+ * De-initialize the DP aux. Disable all interrupts which are enabled
+ * through aux initialization, as well as the transmitter.
+ */
+static void xlnx_dp_exit_aux(struct xlnx_dp *dp)
+{
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 0);
+	xlnx_dp_write(dp->dp_base, XDPTX_INTR_MASK_REG, 0xfff);
+}
+
+/**
+ * xlnx_dp_update_misc - Write the misc registers
+ * @dp: DisplayPort IP core structure
+ *
+ * The misc register values are stored in the structure, and this
+ * function applies the values into the registers.
+ */
+static void xlnx_dp_update_misc(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_config *config = &dp->config;
+
+	if (!dp->colorimetry_through_vsc) {
+		xlnx_dp_write(dp->dp_base, XDPTX_MAINSTRM_MISC0_REG,
+			      config->misc0);
+		xlnx_dp_write(dp->dp_base, XDPTX_MAINSTRM_MISC1_REG, 0x0);
+	} else {
+		xlnx_dp_set(dp->dp_base, XDPTX_MAINSTRM_MISC1_REG,
+			    XDPTX_MAINSTRM_MISC1_TIMING_IGNORED_MASK);
+	}
+}
+
+/**
+ * xlnx_dp_set_sync_mode - Set the sync mode bit in the software misc state
+ * @dp: DisplayPort IP core structure
+ * @mode: flag if the sync mode should be on or off
+ *
+ * Set the bit in software misc state. To apply to hardware,
+ * xlnx_dp_update_misc() should be called.
+ */
+static void xlnx_dp_set_sync_mode(struct xlnx_dp *dp, bool mode)
+{
+	struct xlnx_dp_config *config = &dp->config;
+
+	if (mode)
+		config->misc0 |= XDPTX_MAINSTRM_MISC0_MASK;
+	else
+		config->misc0 &= ~XDPTX_MAINSTRM_MISC0_MASK;
+}
+
+static void xlnx_dp_vsc_pkt_handler(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_vscpkt *vscpkt = &dp->vscpkt;
+	int i;
+
+	if (dp->colorimetry_through_vsc) {
+		xlnx_dp_write(dp->dp_base, XDPTX_AUDIO_EXT_DATA(1),
+			      vscpkt->header);
+		for (i = 0; i < XDPTX_AUDIO_EXT_DATA_2ND_TO_9TH_WORD; i++) {
+			xlnx_dp_write(dp->dp_base, XDPTX_AUDIO_EXT_DATA(i + 2),
+				      vscpkt->payload[i]);
+		}
+	}
+}
+
+static void xlnx_dp_prepare_vsc(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_config *config = &dp->config;
+	struct xlnx_dp_vscpkt *vscpkt = &dp->vscpkt;
+	int i;
+	u32 payload_data = 0, bpc;
+
+	vscpkt->header = XDPTX_VSC_SDP_PIXELENC_HEADER_MASK;
+	payload_data |= config->fmt << XDPTX_VSC_SDP_FMT_SHIFT;
+
+	switch (config->bpc) {
+	case 6:
+		bpc = 0x0;
+		break;
+	case 8:
+		bpc = 0x1;
+		break;
+	case 10:
+		bpc = 0x2;
+		break;
+	case 12:
+		bpc = 0x3;
+		break;
+	case 16:
+		bpc = 0x4;
+		break;
+	default:
+		dev_err(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n",
+			config->bpc);
+		bpc = 0x0;
+	}
+
+	bpc &= XDPTX_VSC_SDP_BPC_MASK;
+	payload_data |= (bpc << XDPTX_VSC_SDP_BPC_SHIFT);
+	/* TODO: it has to be dynamic */
+	payload_data |= (0x1 << XDPTX_VSC_SDP_DYNAMIC_RANGE_SHIFT);
+
+	dev_dbg(dp->dev, "payload_data 0x%x", payload_data);
+
+	/* population vsc payload */
+	for (i = 0; i < 8; i++) {
+		if (i == 4) {
+			vscpkt->payload[i] = payload_data;
+			continue;
+		}
+		vscpkt->payload[i] = 0x0;
+	}
+}
+
+/**
+ * xlnx_dp_set_bpc - Set bpc value in software misc state
+ * @dp: DisplayPort IP core structure
+ * @bpc: bits per component
+ *
+ * Return: 0 on success, or the fallback bpc value
+ */
+static u32 xlnx_dp_set_bpc(struct xlnx_dp *dp, u8 bpc)
+{
+	struct xlnx_dp_config *config = &dp->config;
+	unsigned int ret = 0;
+
+	if (dp->connector.display_info.bpc &&
+	    dp->connector.display_info.bpc != bpc) {
+		dev_err(dp->dev, "requested bpc (%u) != display info (%u)\n",
+			bpc, dp->connector.display_info.bpc);
+		bpc = dp->connector.display_info.bpc;
+	}
+
+	config->misc0 &= ~XDPTX_MISC0_BPC_MASK;
+	switch (bpc) {
+	case 6:
+		config->misc0 |= XDPTX_MISC0_BPC6_MASK;
+		break;
+	case 8:
+		config->misc0 |= XDPTX_MISC0_BPC8_MASK;
+		break;
+	case 10:
+		config->misc0 |= XDPTX_MISC0_BPC10_MASK;
+		break;
+	case 12:
+		config->misc0 |= XDPTX_MISC0_BPC12_MASK;
+		break;
+	case 16:
+		config->misc0 |= XDPTX_MISC0_BPC16_MASK;
+		break;
+	default:
+		dev_err(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n",
+			bpc);
+		config->misc0 |= XDPTX_MISC0_BPC8_MASK;
+		ret = 8;
+	}
+	config->bpc = bpc;
+	xlnx_dp_update_bpp(dp);
+
+	return ret;
+}
+
+/**
+ * xlnx_dp_encoder_mode_set_transfer_unit - Set the transfer unit values
+ * @dp: DisplayPort IP core structure
+ * @mode: requested display mode
+ *
+ * Set the transfer unit, and calculate all transfer unit size related values.
+ * Calculation is based on DP and IP core specification.
+ */
+static void
+xlnx_dp_encoder_mode_set_transfer_unit(struct xlnx_dp *dp,
+				       struct drm_display_mode *mode)
+{
+	struct xlnx_dp_config *config = &dp->config;
+	u32 tu = XDPTX_DEF_TRANSFER_UNITSIZE, temp;
+	u32 bw, vid_kbytes, avg_bytes_per_tu, init_wait, min_bytes_per_tu;
+
+	/* Use the max transfer unit size (default) */
+	xlnx_dp_write(dp->dp_base, XDPTX_TRANSFER_UNITSIZE_REG, tu);
+
+	vid_kbytes = (mode->clock / 1000) * (dp->config.bpp / 8);
+	bw = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
+	avg_bytes_per_tu = vid_kbytes * tu / (dp->mode.lane_cnt * bw);
+	min_bytes_per_tu = avg_bytes_per_tu / 1000;
+	xlnx_dp_write(dp->dp_base, XDPTX_MINBYTES_PERTU_REG,
+		      min_bytes_per_tu);
+
+	temp = (avg_bytes_per_tu % 1000) * 1024 / 1000;
+	xlnx_dp_write(dp->dp_base, XDPTX_FRACBYTES_PERTU_REG, temp);
+
+	init_wait = tu - min_bytes_per_tu;
+
+	/* Configure the initial wait cycle based on transfer unit size */
+	if (min_bytes_per_tu <= 4)
+		init_wait = tu;
+	else if ((config->misc0 & XDPTX_MISC0_YCRCB422_MASK) ==
+		XDPTX_MISC0_YCRCB422_MASK)
+		init_wait = init_wait / 2;
+
+	xlnx_dp_write(dp->dp_base, XDPTX_INIT_WAIT_REG, init_wait);
+}
+
+/**
+ * xlnx_dp_encoder_mode_set_stream - Configure the main stream
+ * @dp: DisplayPort IP core structure
+ * @mode: requested display mode
+ *
+ * Configure the main stream based on the requested mode @mode. Calculation is
+ * based on IP core specification.
+ */
+static void xlnx_dp_encoder_mode_set_stream(struct xlnx_dp *dp,
+					    struct drm_display_mode *mode)
+{
+	void __iomem *dp_base = dp->dp_base;
+	u32 reg, wpl, ppc;
+	u8 lane_cnt = dp->mode.lane_cnt;
+
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_HTOTAL_REG, mode->htotal);
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_VTOTAL_REG, mode->vtotal);
+
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_POL_REG,
+		      (!!(mode->flags & DRM_MODE_FLAG_PVSYNC) <<
+		      XDPTX_MAINSTRM_POLVSYNC_SHIFT) |
+		      (!!(mode->flags & DRM_MODE_FLAG_PHSYNC) <<
+		      XDPTX_MAINSTRM_POLHSYNC_SHIFT));
+
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_HSWIDTH_REG,
+		      mode->hsync_end - mode->hsync_start);
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_VSWIDTH_REG,
+		      mode->vsync_end - mode->vsync_start);
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_HRES_REG, mode->hdisplay);
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_VRES_REG, mode->vdisplay);
+
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_HSTART_REG,
+		      mode->htotal - mode->hsync_start);
+	xlnx_dp_write(dp_base, XDPTX_MAINSTRM_VSTART_REG,
+		      mode->vtotal - mode->vsync_start);
+	xlnx_dp_update_misc(dp);
+
+	if (mode->clock > 530000)
+		ppc = 4;
+	else if (mode->clock > 270000)
+		ppc = 2;
+	else
+		ppc = 1;
+
+	xlnx_dp_write(dp_base, XDPTX_USER_PIXELWIDTH_REG, ppc);
+	dp->config.ppc = ppc;
+
+	xlnx_dp_write(dp_base, XDPTX_M_VID_REG, mode->clock);
+	reg = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
+	xlnx_dp_write(dp_base, XDPTX_N_VID_REG, reg);
+
+	/* In synchronous mode, set the dividers */
+	if (dp->config.misc0 & XDPTX_MAINSTRM_MISC0_MASK) {
+		reg = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
+		xlnx_dp_write(dp_base, XDPTX_N_VID_REG, reg);
+		xlnx_dp_write(dp_base, XDPTX_M_VID_REG, mode->clock);
+	}
+
+	wpl = (mode->hdisplay * dp->config.bpp + 15) / 16;
+	reg = wpl + wpl % lane_cnt - lane_cnt;
+	xlnx_dp_write(dp_base, XDPTX_USER_DATACNTPERLANE_REG, reg);
+}
+
+static void xlnx_dp_mainlink_en(struct xlnx_dp *dp, u8 enable)
+{
+	xlnx_dp_write(dp->dp_base, XDPTX_SCRAMBLER_RESET,
+		      XDPTX_SCRAMBLER_RESET_MASK);
+	xlnx_dp_write(dp->dp_base, XDPTX_MAINSTRM_ENABLE_REG, enable);
+}
+
+static int xlnx_dp_power_cycle(struct xlnx_dp *dp)
+{
+	int ret = 0, i;
+	u8 value;
+
+	/* sink Power cycle */
+	for (i = 0; i < XDPTX_SINK_PWR_CYCLES; i++) {
+		ret = drm_dp_dpcd_readb(&dp->aux, DP_SET_POWER, &value);
+
+		value &= ~DP_SET_POWER_MASK;
+		value |= DP_SET_POWER_D3;
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, value);
+
+		usleep_range(300, 400);
+		value &= ~DP_SET_POWER_MASK;
+		value |= DP_SET_POWER_D0;
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, value);
+		usleep_range(300, 400);
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, value);
+		if (ret == 1)
+			break;
+		usleep_range(3000, 4000);
+	}
+
+	if (ret < 0) {
+		dev_err(dp->dev, "DP aux failed\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dp_start - start the DisplayPort core
+ * @dp: DisplayPort IP core structure
+ *
+ * This function trains the DisplayPort link based on the sink capabilities and
+ * enables the main link.
+ */
+static void xlnx_dp_start(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_mode *mode = &dp->mode;
+	int link_rate = dp->link_config.link_rate;
+	int ret = 0;
+	u32 val, intr_mask;
+	u8 data;
+	bool enhanced;
+
+	mode->bw_code = drm_dp_link_rate_to_bw_code(link_rate);
+	mode->lane_cnt = dp->link_config.lane_count;
+	dp->link_config.cr_done_oldstate = dp->link_config.max_lanes;
+
+	xlnx_dp_init_aux(dp);
+	if (dp->status != connector_status_connected) {
+		dev_info(dp->dev, "Display not connected\n");
+		return;
+	}
+
+	xlnx_dp_power_cycle(dp);
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 0);
+	/*
+	 * Give a bit of time for DP IP after monitor came up and starting
+	 * link training
+	 */
+	msleep(100);
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 1);
+
+	ret = xlnx_dp_set_linkrate(dp, mode->bw_code);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set link rate\n");
+		return;
+	}
+
+	ret = xlnx_dp_set_lanecount(dp, mode->lane_cnt);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set lane count\n");
+		return;
+	}
+
+	/* Disable MST mode in both the RX and TX */
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_MSTM_CTRL, 0);
+	if (ret < 0) {
+		dev_dbg(dp->dev, "DPCD write failed");
+		return;
+	}
+	xlnx_dp_write(dp->dp_base, XDPTX_MST_CONFIG, 0x0);
+
+	/* Disable main link during training. */
+	val = xlnx_dp_read(dp->dp_base, XDPTX_MAINSTRM_ENABLE_REG);
+	if (val)
+		xlnx_dp_mainlink_en(dp, 0x0);
+
+	/* Disable HPD pulse interrupts during link training */
+	intr_mask = xlnx_dp_read(dp->dp_base, XDPTX_INTR_MASK_REG);
+	xlnx_dp_write(dp->dp_base, XDPTX_INTR_MASK_REG,
+		      intr_mask | XDPTX_INTR_HPDPULSE_MASK);
+
+	/* Enable clock spreading for both DP TX and RX device */
+	drm_dp_dpcd_readb(&dp->aux, DP_DOWNSPREAD_CTRL, &data);
+	if (dp->dpcd[DP_MAX_DOWNSPREAD] & 0x1) {
+		xlnx_dp_write(dp->dp_base, XDPTX_DOWNSPREAD_CTL_REG, 1);
+		data |=  XDPTX_DPCD_SPREAD_AMP_MASK;
+	} else {
+		xlnx_dp_write(dp->dp_base, XDPTX_DOWNSPREAD_CTL_REG, 0);
+		data &= ~XDPTX_DPCD_SPREAD_AMP_MASK;
+	}
+	drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, data);
+
+	/* Enahanced framing model */
+	drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data);
+	enhanced = drm_dp_enhanced_frame_cap(dp->dpcd);
+	if (enhanced) {
+		xlnx_dp_write(dp->dp_base, XDPTX_EFRAME_EN_REG, 1);
+		data |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
+	}
+
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, data);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set lane count\n");
+		return;
+	}
+	/* set channel encoding */
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_MAIN_LINK_CHANNEL_CODING_SET,
+				 DP_SET_ANSI_8B10B);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to set ANSI 8B/10B encoding\n");
+		return;
+	}
+	/* Reset PHY */
+	xlnx_dp_phy_reset(dp, XDPTX_PHYCONFIG_RESET_MASK);
+
+	/* Wait for PHY ready */
+	ret = xlnx_dp_phy_ready(dp);
+	if (ret < 0)
+		return;
+
+	memset(dp->train_set, 0, XDPTX_MAX_LANES);
+
+	ret = xlnx_dp_run_training(dp);
+	if (ret < 0) {
+		dev_err(dp->dev, "DP Link Training Failed\n");
+		return;
+	}
+
+	ret = xlnx_dp_post_training(dp);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed post trining settings\n");
+		return;
+	}
+
+	/* re-enable main link after training if required */
+	if (val)
+		xlnx_dp_mainlink_en(dp, 0x1);
+	/* Enable HDP interrupts after link training */
+	xlnx_dp_write(dp->dp_base, XDPTX_INTR_MASK_REG, intr_mask);
+
+	dev_dbg(dp->dev, "Training done:");
+
+	/* reset the transmitter */
+	xlnx_dp_write(dp->dp_base, XDPTX_SOFT_RST,
+		      XDPTX_SOFT_RST_VIDEO_STREAM_ALL_MASK |
+		      XDPTX_SOFT_RST_HDCP_MASK);
+	xlnx_dp_write(dp->dp_base, XDPTX_SOFT_RST, 0x0);
+
+	/* Enable VTC and MainStream */
+	xlnx_dp_set(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_CTL,
+		    XDPTX_VTC_CTL_GE);
+	xlnx_dp_mainlink_en(dp, 0x1);
+
+	ret = xlnx_dp_check_link_status(dp);
+	if (ret < 0) {
+		dev_err(dp->dev, "Link is DOWN after main link enabled!\n");
+		return;
+	}
+	if (dp->colorimetry_through_vsc) {
+		/* program the VSC extended packet */
+		xlnx_dp_vsc_pkt_handler(dp);
+		/* This ensures that VSC pkt is sent every frame */
+		xlnx_dp_set(dp->dp_base, XDPTX_MAINSTRM_MISC0_REG,
+			    XDPTX_MAINSTRM_MISC0_EXT_VSYNC_MASK);
+	}
+	/* enable audio */
+	xlnx_dp_set(dp->dp_base, XDPTX_AUDIO_CTRL_REG, 0x1);
+	/* Enabling TX interrupts */
+	xlnx_dp_write(dp->dp_base, XDPTX_INTR_MASK_REG, 0);
+}
+
+/**
+ * xlnx_dp_stop - stop the DisplayPort core
+ * @dp: DisplayPort IP core structure
+ *
+ * This function disables the DisplayPort main link and VTC.
+ */
+static void xlnx_dp_stop(struct xlnx_dp *dp)
+{
+	struct phy_configure_opts_dp *phy_cfg = &dp->phy_opts.dp;
+
+	xlnx_dp_write(dp->dp_base, XDPTX_MAINSTRM_ENABLE_REG, 0);
+
+	/* Disabling the audio in dp core */
+	xlnx_dp_clr(dp->dp_base, XDPTX_AUDIO_CTRL_REG, 0);
+
+	/* set Vs and Pe to 0, 0 on cable disconnect */
+	phy_cfg->pre[0] = 0;
+	phy_cfg->voltage[0] = 0;
+	phy_cfg->set_voltages = 1;
+
+	if (!dp->config.versal_gt_present)
+		phy_configure(dp->phy[0], &dp->phy_opts);
+	else
+		xlnx_dp_tx_pe_vs_adjust_handler(dp, &dp->phy_opts.dp);
+
+	/* Disable VTC */
+	xlnx_dp_clr(dp->dp_base, XDPTX_VTC_BASE + XDPTX_VTC_CTL,
+		    XDPTX_VTC_CTL_GE);
+}
+
+static int xlnx_dp_txconnected(struct xlnx_dp *dp)
+{
+	u32 status;
+	u8 retries = 0;
+
+	do {
+		status = xlnx_dp_read(dp->dp_base,
+				      XDPTX_INTR_SIGSTATE_REG) & 0x1;
+		if (retries > 5)
+			return false;
+		retries++;
+		usleep_range(1000, 1100);
+	} while (status == 0);
+
+	return true;
+}
+
+/*
+ * DRM connector functions
+ */
+static enum drm_connector_status
+xlnx_dp_connector_detect(struct drm_connector *connector, bool force)
+{
+	struct xlnx_dp *dp = connector_to_dp(connector);
+	struct xlnx_dp_link_config *link_config = &dp->link_config;
+	struct xlnx_dp_mode *mode = &dp->mode;
+	int ret;
+	u8 dpcd_ext[DP_RECEIVER_CAP_SIZE];
+	u8 max_link_rate, ext_cap_rd = 0, data;
+
+	if (!xlnx_dp_txconnected(dp)) {
+		dev_dbg(dp->dev, "Display is not connected");
+		goto disconnected;
+	}
+
+	/* Reading the Ext capability for compliance */
+	ret = drm_dp_dpcd_read(&dp->aux, DP_DP13_DPCD_REV, dpcd_ext,
+			       sizeof(dpcd_ext));
+	if ((dp->dpcd[6] & 0x1) == 0x1) {
+		ret = drm_dp_dpcd_read(&dp->aux, DP_DOWNSTREAM_PORT_0,
+				       dpcd_ext, sizeof(dpcd_ext));
+	}
+
+	ret = drm_dp_dpcd_read(&dp->aux, DP_DPCD_REV, dp->dpcd,
+			       sizeof(dp->dpcd));
+	if (ret < 0) {
+		dev_dbg(dp->dev, "DPCD read first try fails");
+		ret = drm_dp_dpcd_read(&dp->aux, DP_DPCD_REV, dp->dpcd,
+				       sizeof(dp->dpcd));
+		if (ret < 0) {
+			dev_info(dp->dev, "DPCD read failes");
+			goto disconnected;
+		}
+	}
+	/* set MaxLinkRate to TX rate, if sink provides a non-standard value */
+	if (dp->dpcd[DP_MAX_LINK_RATE] != DP_LINK_BW_8_1 &&
+	    dp->dpcd[DP_MAX_LINK_RATE] != DP_LINK_BW_5_4 &&
+	    dp->dpcd[DP_MAX_LINK_RATE] != DP_LINK_BW_2_7 &&
+	    dp->dpcd[DP_MAX_LINK_RATE] != DP_LINK_BW_1_62) {
+		dp->dpcd[DP_MAX_LINK_RATE] = DP_LINK_BW_8_1;
+	}
+
+	if (dp->dpcd[DP_TRAINING_AUX_RD_INTERVAL] &
+	    DP_EXTENDED_RECEIVER_CAP_FIELD_PRESENT) {
+		ret = drm_dp_dpcd_read(&dp->aux, DP_DP13_MAX_LINK_RATE,
+				       &max_link_rate, 1);
+		if (ret < 0) {
+			dev_dbg(dp->dev, "DPCD read failed");
+			goto disconnected;
+		}
+
+		if (max_link_rate == DP_LINK_BW_8_1)
+			dp->dpcd[DP_MAX_LINK_RATE] = DP_LINK_BW_8_1;
+
+		/* compliance: UCD400 required reading these extended registers */
+		ret = drm_dp_dpcd_read(&dp->aux, DP_DP13_MAX_LINK_RATE,
+				       &ext_cap_rd, 1);
+		ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT_ESI,
+				       &ext_cap_rd, 1);
+		ret = drm_dp_dpcd_read(&dp->aux,
+				       DP_DEVICE_SERVICE_IRQ_VECTOR_ESI0,
+				       &ext_cap_rd, 1);
+		ret = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS_ESI,
+				       &ext_cap_rd, 1);
+		ret = drm_dp_dpcd_read(&dp->aux, DP_LANE2_3_STATUS_ESI,
+				       &ext_cap_rd, 1);
+		ret = drm_dp_dpcd_read(&dp->aux,
+				       DP_LANE_ALIGN_STATUS_UPDATED_ESI,
+				       &ext_cap_rd, 1);
+		ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_STATUS_ESI,
+				       &ext_cap_rd, 1);
+		if (ret < 0)
+			dev_dbg(dp->dev, "DPCD read fails");
+	}
+
+	link_config->max_rate = min_t(int,
+				      drm_dp_max_link_rate(dp->dpcd),
+				      dp->config.max_link_rate);
+	link_config->max_lanes = min_t(u8,
+				       drm_dp_max_lane_count(dp->dpcd),
+				       dp->config.max_lanes);
+	link_config->link_rate = link_config->max_rate;
+	link_config->lane_count = link_config->max_lanes;
+	mode->lane_cnt = link_config->max_lanes;
+	mode->bw_code = drm_dp_link_rate_to_bw_code(link_config->link_rate);
+
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_DPRX_FEATURE_ENUMERATION_LIST,
+				&data);
+	if (ret < 0) {
+		dev_dbg(dp->dev, "DPCD read failed");
+		goto disconnected;
+	}
+	dp->status = connector_status_connected;
+
+	if (data & DP_VSC_SDP_EXT_FOR_COLORIMETRY_SUPPORTED)
+		dp->colorimetry_through_vsc = true;
+	else
+		dp->colorimetry_through_vsc = false;
+
+	if (dp->enabled) {
+		xlnx_dp_stop(dp);
+		xlnx_dp_start(dp);
+	}
+
+	return connector_status_connected;
+disconnected:
+	dp->status = connector_status_disconnected;
+	if (dp->enabled)
+		xlnx_dp_stop(dp);
+
+	return connector_status_disconnected;
+}
+
+static int xlnx_dp_connector_get_modes(struct drm_connector *connector)
+{
+	struct xlnx_dp *dp = connector_to_dp(connector);
+	struct edid *edid;
+	int ret;
+
+	edid = drm_get_edid(connector, &dp->aux.ddc);
+	if (!edid) {
+		drm_connector_update_edid_property(connector, NULL);
+		dp->have_edid = false;
+		return 0;
+	}
+
+	drm_connector_update_edid_property(connector, edid);
+	ret = drm_add_edid_modes(connector, edid);
+	dp->have_edid = true;
+	kfree(edid);
+
+	return ret;
+}
+
+static struct drm_encoder *
+xlnx_dp_connector_best_encoder(struct drm_connector *connector)
+{
+	struct xlnx_dp *dp = connector_to_dp(connector);
+
+	return &dp->encoder;
+}
+
+static int xlnx_dp_connector_mode_valid(struct drm_connector *connector,
+					struct drm_display_mode *mode)
+{
+	struct xlnx_dp *dp = connector_to_dp(connector);
+	u8 max_lanes = dp->link_config.max_lanes;
+	u8 bpp = dp->config.bpp;
+	int max_rate = dp->link_config.max_rate;
+	int rate;
+
+	if (mode->clock > XDPTX_MAX_FREQ) {
+		dev_info(dp->dev, "filtered the mode, %s,for high pixel rate\n",
+			 mode->name);
+		drm_mode_debug_printmodeline(mode);
+		return MODE_CLOCK_HIGH;
+	}
+
+	/* check with link rate and lane count */
+	rate = XDPTX_MAX_RATE(max_rate, max_lanes, bpp);
+	if (mode->clock > rate) {
+		dev_dbg(dp->dev, "filtered the mode, %s,for high pixel rate\n",
+			mode->name);
+		drm_mode_debug_printmodeline(mode);
+
+		return MODE_CLOCK_HIGH;
+	}
+
+	return MODE_OK;
+}
+
+static void xlnx_dp_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+}
+
+static int
+xlnx_dp_connector_atomic_set_property(struct drm_connector *connector,
+				      struct drm_connector_state *state,
+				      struct drm_property *property,
+				      uint64_t val)
+{
+	struct xlnx_dp *dp = connector_to_dp(connector);
+	unsigned int bpc;
+
+	if (property == dp->sync_prop) {
+		xlnx_dp_set_sync_mode(dp, val);
+	} else if (property == dp->bpc_prop) {
+		bpc = xlnx_dp_set_bpc(dp, val);
+		if (bpc) {
+			drm_object_property_set_value(&connector->base,
+						      property, bpc);
+			return -EINVAL;
+		}
+	} else {
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int
+xlnx_dp_connector_atomic_get_property(struct drm_connector *connector,
+				      const struct drm_connector_state *state,
+					struct drm_property *property,
+					uint64_t *val)
+{
+	struct xlnx_dp *dp = connector_to_dp(connector);
+
+	if (property == dp->sync_prop)
+		*val = (dp->config.misc0 & XDPTX_MAINSTRM_MISC0_MASK);
+	else if (property == dp->bpc_prop)
+		*val = dp->config.bpc;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct drm_connector_funcs xlnx_dp_connector_funcs = {
+	.detect			= xlnx_dp_connector_detect,
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= xlnx_dp_connector_destroy,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_set_property	= xlnx_dp_connector_atomic_set_property,
+	.atomic_get_property	= xlnx_dp_connector_atomic_get_property,
+};
+
+static struct drm_connector_helper_funcs xlnx_dp_connector_helper_funcs = {
+	.get_modes	= xlnx_dp_connector_get_modes,
+	.best_encoder	= xlnx_dp_connector_best_encoder,
+	.mode_valid	= xlnx_dp_connector_mode_valid,
+};
+
+static int xlnx_dp_get_eld(struct device *dev, u8 *buf, size_t len)
+{
+	struct xlnx_dp *dp = dev_get_drvdata(dev);
+	size_t size;
+
+	if (!dp->have_edid)
+		return -EIO;
+
+	size = drm_eld_size(dp->connector.eld);
+	if (!size)
+		return -EINVAL;
+
+	if (len < size)
+		size = len;
+	memcpy(buf, dp->connector.eld, size);
+
+	return 0;
+}
+
+static unsigned long dp_codec_spk_mask_from_alloc(int spk_alloc)
+{
+	int i;
+	static const unsigned long dp_codec_eld_spk_alloc_bits[] = {
+		[0] = FL | FR, [1] = LFE, [2] = FC, [3] = RL | RR,
+		[4] = RC, [5] = FLC | FRC, [6] = RLC | RRC,
+	};
+	unsigned long spk_mask = 0;
+
+	for (i = 0; i < ARRAY_SIZE(dp_codec_eld_spk_alloc_bits); i++) {
+		if (spk_alloc & (1 << i))
+			spk_mask |= dp_codec_eld_spk_alloc_bits[i];
+	}
+
+	return spk_mask;
+}
+
+static int dp_codec_get_ch_alloc_table_idx(u8 *eld, u8 channels)
+{
+	int i;
+	u8 spk_alloc;
+	unsigned long spk_mask;
+	const struct dp_codec_cea_spk_alloc *cap = dp_codec_channel_alloc;
+
+	spk_alloc = drm_eld_get_spk_alloc(eld);
+	spk_mask = dp_codec_spk_mask_from_alloc(spk_alloc);
+
+	for (i = 0; i < ARRAY_SIZE(dp_codec_channel_alloc); i++, cap++) {
+		/* If spk_alloc == 0, DP is unplugged return stereo config */
+		if (!spk_alloc && cap->ca_id == 0)
+			return i;
+		if (cap->n_ch != channels)
+			continue;
+		if (!(cap->mask == (spk_mask & cap->mask)))
+			continue;
+		return i;
+	}
+
+	return -EINVAL;
+}
+
+static int dp_codec_fill_cea_params(struct snd_pcm_substream *substream,
+				    struct snd_soc_dai *dai,
+				    unsigned int channels,
+				    struct hdmi_audio_infoframe *cea)
+{
+	int idx;
+	int ret;
+	u8 eld[MAX_ELD_BYTES];
+
+	ret = xlnx_dp_get_eld(dai->dev, eld, sizeof(eld));
+	if (ret)
+		return ret;
+
+	ret = snd_pcm_hw_constraint_eld(substream->runtime, eld);
+	if (ret)
+		return ret;
+
+	/* Select a channel allocation that matches with ELD and pcm channels */
+	idx = dp_codec_get_ch_alloc_table_idx(eld, channels);
+	if (idx < 0) {
+		dev_err(dai->dev, "Not able to map channels to speakers (%d)\n",
+			idx);
+		return idx;
+	}
+
+	hdmi_audio_infoframe_init(cea);
+	cea->channels = channels;
+	cea->coding_type = HDMI_AUDIO_CODING_TYPE_STREAM;
+	cea->sample_size = HDMI_AUDIO_SAMPLE_SIZE_STREAM;
+	cea->sample_frequency = HDMI_AUDIO_SAMPLE_FREQUENCY_STREAM;
+	cea->channel_allocation = dp_codec_channel_alloc[idx].ca_id;
+
+	return 0;
+}
+
+/**
+ * xlnx_tx_pcm_startup - initialize audio during audio usecase
+ * @substream: PCM substream
+ * @dai: runtime dai data
+ *
+ * This function is called by ALSA framework before audio
+ * playback begins. This callback initializes audio.
+ *
+ * Return: 0 on success
+ */
+static int xlnx_tx_pcm_startup(struct snd_pcm_substream *substream,
+			       struct snd_soc_dai *dai)
+{
+	struct xlnx_dp *dp = dev_get_drvdata(dai->dev);
+
+	/* Enabling the audio in dp core */
+	xlnx_dp_clr(dp->dp_base, XDPTX_AUDIO_CTRL_REG, XDPTX_AUDIO_EN_MASK);
+
+	xlnx_dp_set(dp->dp_base, XDPTX_AUDIO_CTRL_REG, XDPTX_AUDIO_EN_MASK);
+
+	return 0;
+}
+
+/**
+ * xlnx_tx_pcm_hw_params - sets the playback stream properties
+ * @substream: PCM substream
+ * @params: PCM stream hardware parameters
+ * @dai: runtime dai data
+ *
+ * This function is called by ALSA framework after startup callback
+ * packs the audio infoframe from stream paremters and programs ACR
+ * block
+ *
+ * Return: 0 on success
+ */
+static int xlnx_tx_pcm_hw_params(struct snd_pcm_substream *substream,
+				 struct snd_pcm_hw_params *params,
+				 struct snd_soc_dai *dai)
+{
+	struct hdmi_audio_infoframe infoframe;
+	struct xlnx_dp *dp = dev_get_drvdata(dai->dev);
+	int ret;
+	u8 infopckt[DP_INFOFRAME_SIZE(AUDIO)] = {0};
+	u8 *ptr = (u8 *)dp->tx_audio_data->buffer;
+
+	ret = dp_codec_fill_cea_params(substream, dai,
+				       params_channels(params),
+				       &infoframe);
+	if (ret < 0)
+		return ret;
+
+	/* Setting audio channels */
+	xlnx_dp_write(dp->dp_base, XDPTX_AUDIO_CHANNELS_REG,
+		      infoframe.channels - 1);
+
+	hdmi_audio_infoframe_pack(&infoframe, infopckt,
+				  DP_INFOFRAME_SIZE(AUDIO));
+	/* Setting audio infoframe packet header. Please refer to PG 299 */
+	ptr[0] = 0x00;
+	ptr[1] = 0x84;
+	ptr[2] = 0x1B;
+	ptr[3] = 0x44;
+	memcpy((void *)(&ptr[4]), (void *)(&infopckt[4]),
+	       (DP_INFOFRAME_SIZE(AUDIO) - DP_INFOFRAME_HEADER_SIZE));
+
+	return 0;
+}
+
+/**
+ * xlnx_tx_pcm_shutdown - Deinitialze audio when audio usecase is stopped
+ * @substream: PCM substream
+ * @dai: runtime dai data
+ *
+ * This function is called by ALSA framework before audio playback usecase
+ * ends.
+ */
+static void xlnx_tx_pcm_shutdown(struct snd_pcm_substream *substream,
+				 struct snd_soc_dai *dai)
+{
+	struct xlnx_dp *dp = dev_get_drvdata(dai->dev);
+
+	/* Disabling the audio in dp core */
+	xlnx_dp_clr(dp->dp_base, XDPTX_AUDIO_CTRL_REG, XDPTX_AUDIO_EN_MASK);
+}
+
+/**
+ * xlnx_tx_pcm_digital_mute - mute or unmute audio
+ * @dai: runtime dai data
+ * @enable: enable or disable mute
+ * @direction: direction to enable mute (capture/playback)
+ *
+ * This function is called by ALSA framework before audio usecase
+ * starts and before audio usecase ends
+ *
+ * Return: 0 on success
+ */
+static int xlnx_tx_pcm_digital_mute(struct snd_soc_dai *dai, int enable,
+				    int direction)
+{
+	struct xlnx_dp *dp = dev_get_drvdata(dai->dev);
+
+	if (enable)
+		xlnx_dp_set(dp->dp_base, XDPTX_AUDIO_CTRL_REG, XDPTX_AUDIO_MUTE_MASK);
+	else
+		xlnx_dp_clr(dp->dp_base, XDPTX_AUDIO_CTRL_REG, XDPTX_AUDIO_MUTE_MASK);
+
+	return 0;
+}
+
+static const struct snd_soc_dai_ops xlnx_dp_tx_dai_ops = {
+	.startup = xlnx_tx_pcm_startup,
+	.hw_params = xlnx_tx_pcm_hw_params,
+	.shutdown = xlnx_tx_pcm_shutdown,
+	.mute_stream = xlnx_tx_pcm_digital_mute,
+	.no_capture_mute = 1,
+};
+
+static struct snd_soc_dai_driver xlnx_dp_tx_dai = {
+	.name = "xlnx_dp_tx",
+	.playback = {
+		.stream_name = "I2S Playback",
+		.channels_min = 2,
+		.channels_max = 8,
+		.rates = DP_RATES,
+		.formats = I2S_FORMATS,
+		.sig_bits = 24,
+	},
+	.ops = &xlnx_dp_tx_dai_ops,
+};
+
+static int xlnx_tx_codec_probe(struct snd_soc_component *component)
+{
+	return 0;
+}
+
+static void xlnx_tx_codec_remove(struct snd_soc_component *component)
+{
+}
+
+static const struct snd_soc_component_driver xlnx_dp_component = {
+	.probe = xlnx_tx_codec_probe,
+	.remove = xlnx_tx_codec_remove,
+};
+
+static int dptx_register_aud_dev(struct device *dev)
+{
+	return devm_snd_soc_register_component(dev, &xlnx_dp_component,
+			&xlnx_dp_tx_dai, 1);
+}
+
+static void xlnx_dp_encoder_enable(struct drm_encoder *encoder)
+{
+	struct xlnx_dp *dp = encoder_to_dp(encoder);
+
+	pm_runtime_get_sync(dp->dev);
+
+	if (!dp->enabled) {
+		dp->enabled = true;
+		xlnx_dp_start(dp);
+	}
+}
+
+static void xlnx_dp_encoder_disable(struct drm_encoder *encoder)
+{
+	struct xlnx_dp *dp = encoder_to_dp(encoder);
+
+	if (dp->enabled) {
+		dp->enabled = false;
+		cancel_delayed_work(&dp->hpd_work);
+		cancel_delayed_work(&dp->hpd_pulse_work);
+		xlnx_dp_stop(dp);
+	}
+	pm_runtime_put_sync(dp->dev);
+}
+
+static void
+xlnx_dp_encoder_atomic_mode_set(struct drm_encoder *encoder,
+				struct drm_crtc_state *crtc_state,
+				struct drm_connector_state *connector_state)
+{
+	struct xlnx_dp *dp = encoder_to_dp(encoder);
+	struct drm_display_mode *mode = &crtc_state->mode;
+	struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+	int rate, max_rate = dp->link_config.max_rate;
+	u32 clock, drm_fourcc;
+	u8 max_lanes = dp->link_config.max_lanes;
+	u8 bpp = dp->config.bpp;
+
+	/*
+	 * This assumes that there is no conversion  between framebuffer
+	 * and DP Tx
+	 */
+	drm_fourcc = encoder->crtc->primary->state->fb->format->format;
+
+	xlnx_dp_set_color(dp, drm_fourcc);
+
+	rate = XDPTX_MAX_RATE(max_rate, max_lanes, bpp);
+	if (mode->clock > rate) {
+		dev_err(dp->dev, "the mode, %s,has too high pixel rate\n",
+			mode->name);
+		drm_mode_debug_printmodeline(mode);
+	}
+
+	/* The timing register should be programmed always */
+	xlnx_dp_encoder_mode_set_stream(dp, adjusted_mode);
+	xlnx_dp_encoder_mode_set_transfer_unit(dp, adjusted_mode);
+	clock = adjusted_mode->clock * 1000;
+	clk_set_rate(dp->tx_vid_clk, clock / dp->config.ppc);
+
+	xlnx_dp_vtc_set_timing(dp, adjusted_mode);
+	/* prepare a vsc packet */
+	xlnx_dp_prepare_vsc(dp);
+}
+
+static const struct drm_encoder_funcs xlnx_dp_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+static const struct drm_encoder_helper_funcs xlnx_dp_encoder_helper_funcs = {
+	.enable			= xlnx_dp_encoder_enable,
+	.disable		= xlnx_dp_encoder_disable,
+	.atomic_mode_set	= xlnx_dp_encoder_atomic_mode_set,
+};
+
+static void xlnx_dp_hpd_work_func(struct work_struct *work)
+{
+	struct xlnx_dp *dp;
+
+	dp = container_of(work, struct xlnx_dp, hpd_work.work);
+
+	if (dp->drm)
+		drm_helper_hpd_irq_event(dp->drm);
+}
+
+static struct drm_prop_enum_list xlnx_dp_bpc_enum[] = {
+	{ 6, "6BPC" },
+	{ 8, "8BPC" },
+	{ 10, "10BPC" },
+	{ 12, "12BPC" },
+};
+
+static int xlnx_dp_bind(struct device *dev, struct device *master, void *data)
+{
+	struct xlnx_dp *dp = dev_get_drvdata(dev);
+	struct drm_encoder *encoder = &dp->encoder;
+	struct drm_connector *connector = &dp->connector;
+	struct drm_device *drm = data;
+	unsigned int ret;
+
+	encoder->possible_crtcs = 1;
+	drm_encoder_init(drm, encoder, &xlnx_dp_encoder_funcs,
+			 DRM_MODE_ENCODER_TMDS, NULL);
+	drm_encoder_helper_add(encoder, &xlnx_dp_encoder_helper_funcs);
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+	ret = drm_connector_init(encoder->dev, connector,
+				 &xlnx_dp_connector_funcs,
+				 DRM_MODE_CONNECTOR_DisplayPort);
+	if (ret) {
+		dev_err(dp->dev, "failed to initialize the drm connector");
+		goto error_encoder;
+	}
+
+	drm_connector_helper_add(connector, &xlnx_dp_connector_helper_funcs);
+	drm_connector_register(connector);
+	drm_connector_attach_encoder(connector, encoder);
+	connector->dpms = DRM_MODE_DPMS_OFF;
+
+	dp->drm = drm;
+	dp->sync_prop = drm_property_create_bool(drm, 0, "sync");
+	dp->bpc_prop = drm_property_create_enum(drm, 0, "bpc",
+						xlnx_dp_bpc_enum,
+						ARRAY_SIZE(xlnx_dp_bpc_enum));
+	dp->config.misc0 &= ~XDPTX_MAINSTRM_MISC0_MASK;
+	drm_object_attach_property(&connector->base, dp->sync_prop, false);
+	ret = xlnx_dp_set_bpc(dp, 8);
+	drm_object_attach_property(&connector->base, dp->bpc_prop,
+				   ret ? ret : 8);
+	xlnx_dp_update_bpp(dp);
+
+	/* This enables interrupts, so should be called after DRM init */
+	ret = xlnx_dp_init_aux(dp);
+	if (ret) {
+		dev_err(dp->dev, "failed to initialize DP aux");
+		goto error_prop;
+	}
+	INIT_DELAYED_WORK(&dp->hpd_work, xlnx_dp_hpd_work_func);
+	INIT_DELAYED_WORK(&dp->hpd_pulse_work, xlnx_dp_hpd_pulse_work_func);
+
+	return 0;
+
+error_prop:
+	drm_property_destroy(dp->drm, dp->bpc_prop);
+	drm_property_destroy(dp->drm, dp->sync_prop);
+	xlnx_dp_connector_destroy(&dp->connector);
+error_encoder:
+	drm_encoder_cleanup(&dp->encoder);
+
+	return ret;
+}
+
+static void xlnx_dp_unbind(struct device *dev,
+			   struct device *master, void *data)
+{
+	struct xlnx_dp *dp = dev_get_drvdata(dev);
+
+	cancel_delayed_work_sync(&dp->hpd_work);
+	cancel_delayed_work_sync(&dp->hpd_pulse_work);
+	xlnx_dp_exit_aux(dp);
+	drm_property_destroy(dp->drm, dp->bpc_prop);
+	drm_property_destroy(dp->drm, dp->sync_prop);
+	xlnx_dp_connector_destroy(&dp->connector);
+	drm_encoder_cleanup(&dp->encoder);
+}
+
+static void xlnx_dp_hpd_pulse_work_func(struct work_struct *work)
+{
+	struct xlnx_dp *dp;
+	int ret;
+	u8 link_status[DP_LINK_STATUS_SIZE];
+	u8 bw_set, lane_set;
+
+	dp = container_of(work, struct xlnx_dp, hpd_pulse_work.work);
+
+	if (!dp->enabled)
+		return;
+
+	if (!xlnx_dp_txconnected(dp)) {
+		dev_err(dp->dev, "incorrect HPD pulse received\n");
+		return;
+	}
+
+	/* Read Link information from downstream device */
+	ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+	if (ret < 0)
+		return;
+	ret |= drm_dp_dpcd_read(&dp->aux, DP_LINK_BW_SET, &bw_set, 1);
+	ret |= drm_dp_dpcd_read(&dp->aux, DP_LANE_COUNT_SET, &lane_set, 1);
+	if (ret < 0)
+		return;
+
+	bw_set &= DP_LINK_BW_SET_MASK;
+	if (bw_set != DP_LINK_BW_8_1 &&
+	    bw_set != DP_LINK_BW_5_4 &&
+	    bw_set != DP_LINK_BW_2_7 &&
+	    bw_set != DP_LINK_BW_1_62)
+		goto retrain_link;
+
+	lane_set &= DP_LANE_COUNT_MASK;
+	if (lane_set != 1 && lane_set != 2 && lane_set != 4)
+		goto retrain_link;
+
+	/* Verify the link status */
+	ret = drm_dp_channel_eq_ok(link_status, lane_set);
+	if (!ret)
+		goto retrain_link;
+
+	return;
+
+retrain_link:
+	xlnx_dp_stop(dp);
+	xlnx_dp_start(dp);
+}
+
+static void xlnx_dp_vsync_handler(struct xlnx_dp *dp)
+{
+	int i;
+	u32 fifosts = xlnx_dp_read(dp->dp_base, XDPTX_AUDIO_INFO_BUFF_STATUS);
+
+	if (!(fifosts & (XDPTX_AUDIO_INFO_BUFF_FULL |
+					XDPTX_AUDIO_INFO_BUFF_OVERFLOW))) {
+		/* Write new audio info packet */
+		for (i = 0; i < DP_INFOFRAME_FIFO_SIZE_WORDS; i++) {
+			xlnx_dp_write(dp->dp_base,
+				      XDPTX_AUDIO_INFO_DATA_REG,
+				      dp->tx_audio_data->buffer[i]);
+		}
+	}
+}
+
+static irqreturn_t xlnx_dp_irq_handler(int irq, void *data)
+{
+	struct xlnx_dp *dp = (struct xlnx_dp *)data;
+	u32 intrstatus;
+	u32 hpdduration;
+
+	/* Determine what kind of interrupt occurred. */
+	intrstatus = xlnx_dp_read(dp->dp_base, XDPTX_INTR_STATUS_REG);
+
+	if (!intrstatus)
+		return IRQ_NONE;
+	if (intrstatus & XDPTX_INTR_HPDEVENT_MASK) {
+		dev_dbg_ratelimited(dp->dev, "hpdevent detected\n");
+	} else if (intrstatus & XDPTX_INTR_HPDPULSE_MASK &&
+		   xlnx_dp_txconnected(dp)) {
+		/*
+		 * Some monitors give HPD pulse repeatedly which cause
+		 * HPD pulse function to be executed huge number of times.
+		 * Hence HPD pulse interrupt is disabled if pulse duration
+		 * is longer than 500 microseconds.
+		 */
+		hpdduration = xlnx_dp_read(dp->dp_base, XDPTX_HPD_DURATION_REG);
+		if (hpdduration >= 500)
+			xlnx_dp_write(dp->dp_base, XDPTX_INTR_MASK_REG, 0x10);
+	}
+
+	if (intrstatus & XDPTX_INTR_CHBUFUNDFW_MASK)
+		dev_dbg_ratelimited(dp->dev, "underflow interrupt\n");
+	if (intrstatus & XDPTX_INTR_CHBUFOVFW_MASK)
+		dev_dbg_ratelimited(dp->dev, "overflow interrupt\n");
+
+	if (intrstatus & XDPTX_INTR_HPDEVENT_MASK)
+		schedule_delayed_work(&dp->hpd_work, 0);
+	if (intrstatus & XDPTX_INTR_HPDPULSE_MASK)
+		schedule_delayed_work(&dp->hpd_pulse_work, 0);
+	if (intrstatus & XDPTX_INTR_EXTPKT_TXD_MASK)
+		xlnx_dp_vsc_pkt_handler(dp);
+	if (intrstatus & XDPTX_INTR_VBLANK_MASK)
+		xlnx_dp_vsync_handler(dp);
+
+	return IRQ_HANDLED;
+}
+
+static const struct component_ops xlnx_dp_component_ops = {
+	.bind	= xlnx_dp_bind,
+	.unbind	= xlnx_dp_unbind,
+};
+
+static int xlnx_dp_parse_of(struct xlnx_dp *dp)
+{
+	struct xlnx_dp_config *config = &dp->config;
+	struct device_node *node = dp->dev->of_node;
+	u32 bpc;
+	int ret;
+
+	ret = of_property_read_u32(node, "xlnx,max-lanes", &config->max_lanes);
+	if (ret < 0) {
+		dev_err(dp->dev, "No lane count in DT\n");
+		return ret;
+	}
+	if (config->max_lanes != 1 && config->max_lanes != 2 &&
+	    config->max_lanes != 4) {
+		dev_err(dp->dev, "Invalid max lanes in DT\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-link-rate",
+				   &config->max_link_rate);
+	if (ret < 0) {
+		dev_err(dp->dev, "No link rate in DT\n");
+		return ret;
+	}
+	if (config->max_link_rate != XDPTX_REDUCED_BIT_RATE &&
+	    config->max_link_rate != XDPTX_HIGH_BIT_RATE_1 &&
+	    config->max_link_rate != XDPTX_HIGH_BIT_RATE_2 &&
+	    config->max_link_rate != XDPTX_HIGH_BIT_RATE_3) {
+		dev_err(dp->dev, "Invalid link rate in DT\n");
+		return -EINVAL;
+	}
+
+	xlnx_dp_set_color(dp, DRM_FORMAT_RGB888);
+
+	ret = of_property_read_u32(node, "xlnx,bpc", &bpc);
+	if (ret < 0) {
+		dev_err(dp->dev, "No color depth(bpc) in DT\n");
+		return ret;
+	}
+
+	switch (bpc) {
+	case 6:
+		config->misc0 |= XDPTX_MISC0_BPC6_MASK;
+		break;
+	case 8:
+		config->misc0 |= XDPTX_MISC0_BPC8_MASK;
+		break;
+	case 10:
+		config->misc0 |= XDPTX_MISC0_BPC10_MASK;
+		break;
+	case 12:
+		config->misc0 |= XDPTX_MISC0_BPC12_MASK;
+		break;
+	case 16:
+		config->misc0 |= XDPTX_MISC0_BPC16_MASK;
+		break;
+	default:
+		dev_err(dp->dev, "Not supported color depth in DT\n");
+		return -EINVAL;
+	}
+
+	config->audio_enabled =
+		of_property_read_bool(node, "xlnx,audio-enable");
+
+	config->versal_gt_present =
+		of_property_read_bool(node, "xlnx,versal-gt");
+
+	return 0;
+}
+
+static int xlnx_dp_probe(struct platform_device *pdev)
+{
+	struct device_node *pnode = pdev->dev.of_node;
+	struct device_node *fnode;
+	struct platform_device *iface_pdev;
+	struct xlnx_dp *dp;
+	struct resource *res;
+	void *ptr;
+	unsigned int i;
+	int irq, ret;
+
+	dp = devm_kzalloc(&pdev->dev, sizeof(*dp), GFP_KERNEL);
+	if (!dp)
+		return -ENOMEM;
+
+	dp->tx_audio_data =
+		devm_kzalloc(&pdev->dev, sizeof(struct xlnx_dptx_audio_data),
+			     GFP_KERNEL);
+	if (!dp->tx_audio_data)
+		return -ENOMEM;
+
+	dp->dpms = DRM_MODE_DPMS_OFF;
+	dp->status = connector_status_disconnected;
+	dp->dev = &pdev->dev;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dp_base");
+	dp->dp_base = devm_ioremap_resource(dp->dev, res);
+	if (IS_ERR(dp->dp_base)) {
+		dev_err(&pdev->dev, "couldn't map DisplayPort registers\n");
+		return -ENODEV;
+	}
+
+	ret = xlnx_dp_parse_of(dp);
+	if (ret < 0)
+		return ret;
+
+	if (dp->config.versal_gt_present) {
+		dp->phy[0] = devm_phy_get(dp->dev, "dp-gtquad");
+		if (IS_ERR(dp->phy[0]))
+			return dev_err_probe(dp->dev, ret, "failed to get phy\n");
+
+		ret = phy_init(dp->phy[0]);
+		if (ret)
+			goto error_phy;
+
+		fnode = of_parse_phandle(pnode, "xlnx,xilinx-vfmc", 0);
+		if (!fnode) {
+			dev_err(&pdev->dev, "platform node not found\n");
+			of_node_put(fnode);
+		} else {
+			iface_pdev = of_find_device_by_node(fnode);
+			if (!iface_pdev) {
+				of_node_put(pnode);
+				return -ENODEV;
+			}
+
+			ptr = dev_get_drvdata(&iface_pdev->dev);
+			if (!ptr) {
+				dev_info(&pdev->dev,
+					 "platform device not found -EPROBE_DEFER\n");
+				of_node_put(fnode);
+				return -EPROBE_DEFER;
+			}
+			of_node_put(fnode);
+		}
+	}
+
+	dp->axi_lite_clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+	if (IS_ERR(dp->axi_lite_clk))
+		return PTR_ERR(dp->axi_lite_clk);
+
+	dp->tx_vid_clk = devm_clk_get(&pdev->dev, "tx_vid_clk");
+	if (IS_ERR(dp->tx_vid_clk))
+		dev_err(dp->dev, "failed to get vid clk stream1\n");
+
+	platform_set_drvdata(pdev, dp);
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 0);
+	xlnx_dp_write(dp->dp_base, XDPTX_MAINSTRM_ENABLE_REG, 0);
+
+	dp->tx_link_config.vs_level = 0;
+	dp->tx_link_config.pe_level = 0;
+
+	if (!dp->config.versal_gt_present) {
+		/* acquire vphy lanes */
+		for (i = 0; i < dp->config.max_lanes; i++) {
+			char phy_name[16];
+
+			snprintf(phy_name, sizeof(phy_name), "dp-phy%d", i);
+			dp->phy[i] = devm_phy_get(dp->dev, phy_name);
+			if (IS_ERR(dp->phy[i])) {
+				ret = PTR_ERR(dp->phy[i]);
+				dp->phy[i] = NULL;
+				if (ret == -EPROBE_DEFER) {
+					dev_info(dp->dev,
+						 "xvphy not ready -EPROBE_DEFER\n");
+					return ret;
+				}
+				if (ret != -EPROBE_DEFER)
+					dev_err(dp->dev, "failed to get phy lane %s i %d, error %d\n",
+						phy_name, i, ret);
+				goto error_phy;
+			}
+		}
+
+		ret = xlnx_dp_init_phy(dp);
+		if (ret)
+			goto error_phy;
+	} else {
+		ret = xlnx_dp_tx_gt_control_init(dp);
+		if (ret < 0)
+			return ret;
+	}
+
+	ret = clk_prepare_enable(dp->axi_lite_clk);
+	if (ret) {
+		dev_err(dp->dev, "failed to enable axi_lite_clk (%d)\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(dp->tx_vid_clk);
+	if (ret) {
+		dev_err(dp->dev, "failed to enable tx_vid_clk (%d)\n", ret);
+		goto tx_vid_clk_err;
+	}
+
+	dp->aux.name = "Xlnx DP AUX";
+	dp->aux.dev = dp->dev;
+	dp->aux.transfer = xlnx_dp_aux_transfer;
+	ret = drm_dp_aux_register(&dp->aux);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to initialize DP aux\n");
+		goto error;
+	}
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto error;
+	}
+	ret = devm_request_threaded_irq(dp->dev, irq, NULL,
+					xlnx_dp_irq_handler, IRQF_ONESHOT,
+					dev_name(dp->dev), dp);
+
+	if (ret < 0)
+		goto error;
+
+	if (dp->config.audio_enabled) {
+		if (dptx_register_aud_dev(dp->dev)) {
+			dp->audio_init = false;
+			dev_err(dp->dev, "dp tx audio init failed\n");
+			goto error;
+		} else {
+			dp->audio_init = true;
+			dev_info(dp->dev, "dp tx audio initialized\n");
+		}
+	}
+
+	return component_add(&pdev->dev, &xlnx_dp_component_ops);
+
+tx_vid_clk_err:
+	clk_disable_unprepare(dp->axi_lite_clk);
+error:
+	drm_dp_aux_unregister(&dp->aux);
+error_phy:
+	if (!dp->config.versal_gt_present) {
+		dev_dbg(&pdev->dev, "xdprxss_probe() error_phy:\n");
+		xlnx_dp_exit_phy(dp);
+	} else {
+		phy_exit(dp->phy[0]);
+	}
+
+	return ret;
+}
+
+static int xlnx_dp_remove(struct platform_device *pdev)
+{
+	struct xlnx_dp *dp = platform_get_drvdata(pdev);
+
+	xlnx_dp_write(dp->dp_base, XDPTX_ENABLE_REG, 0);
+	drm_dp_aux_unregister(&dp->aux);
+	if (!dp->config.versal_gt_present)
+		xlnx_dp_exit_phy(dp);
+	else
+		phy_exit(dp->phy[0]);
+	component_del(&pdev->dev, &xlnx_dp_component_ops);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_dp_of_match[] = {
+	{ .compatible = "xlnx,v-dp-txss-3.0", },
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xlnx_dp_of_match);
+
+static struct platform_driver dp_tx_driver = {
+	.probe = xlnx_dp_probe,
+	.remove = xlnx_dp_remove,
+	.driver = {
+		.name = "xlnx-dp-tx",
+		.of_match_table = xlnx_dp_of_match,
+	},
+};
+
+module_platform_driver(dp_tx_driver);
+
+MODULE_AUTHOR("Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx FPGA DisplayPort Tx Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_drv.c
@@ -0,0 +1,533 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS Driver
+ *
+ *  Copyright (C) 2013 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drm_drv.h>
+#include <drm/drm_vblank.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_of.h>
+#include <drm/drm_probe_helper.h>
+
+#include <linux/component.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/dma-resv.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+
+#include "xlnx_bridge.h"
+#include "xlnx_crtc.h"
+#include "xlnx_drv.h"
+#include "xlnx_fb.h"
+#include "xlnx_gem.h"
+
+#define DRIVER_NAME	"xlnx"
+#define DRIVER_DESC	"Xilinx DRM KMS Driver"
+#define DRIVER_DATE	"20130509"
+#define DRIVER_MAJOR	1
+#define DRIVER_MINOR	0
+
+#define MAX_CRTC	3
+
+static uint xlnx_fbdev_vres = 2;
+module_param_named(fbdev_vres, xlnx_fbdev_vres, uint, 0444);
+MODULE_PARM_DESC(fbdev_vres,
+		 "fbdev virtual resolution multiplier for fb (default: 2)");
+
+/**
+ * struct xlnx_drm - Xilinx DRM private data
+ * @drm: DRM core
+ * @crtc: Xilinx DRM CRTC helper
+ * @fb: DRM fb helper
+ * @master: logical master device for pipeline
+ * @suspend_state: atomic state for suspend / resume
+ * @master_count: Counter to track number of fake master instances
+ */
+struct xlnx_drm {
+	struct drm_device *drm;
+	struct xlnx_crtc_helper *crtc;
+	struct drm_fb_helper *fb;
+	struct platform_device *master;
+	struct drm_atomic_state *suspend_state;
+	u32 master_count;
+};
+
+/**
+ * xlnx_get_crtc_helper - Return the crtc helper instance
+ * @drm: DRM device
+ *
+ * Return: the crtc helper instance
+ */
+struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm)
+{
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+	return xlnx_drm->crtc;
+}
+
+/**
+ * xlnx_get_align - Return the align requirement through CRTC helper
+ * @drm: DRM device
+ *
+ * Return: the alignment requirement
+ */
+unsigned int xlnx_get_align(struct drm_device *drm)
+{
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+	return xlnx_crtc_helper_get_align(xlnx_drm->crtc);
+}
+
+/**
+ * xlnx_get_format - Return the current format of CRTC
+ * @drm: DRM device
+ *
+ * Return: the current CRTC format
+ */
+uint32_t xlnx_get_format(struct drm_device *drm)
+{
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+	return xlnx_crtc_helper_get_format(xlnx_drm->crtc);
+}
+
+static void xlnx_output_poll_changed(struct drm_device *drm)
+{
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+	if (xlnx_drm->fb)
+		drm_fb_helper_hotplug_event(xlnx_drm->fb);
+}
+
+static const struct drm_mode_config_funcs xlnx_mode_config_funcs = {
+	.fb_create		= xlnx_fb_create,
+	.output_poll_changed	= xlnx_output_poll_changed,
+	.atomic_check		= drm_atomic_helper_check,
+	.atomic_commit		= drm_atomic_helper_commit,
+};
+
+static void xlnx_mode_config_init(struct drm_device *drm)
+{
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+	struct xlnx_crtc_helper *crtc = xlnx_drm->crtc;
+
+	drm->mode_config.min_width = 0;
+	drm->mode_config.min_height = 0;
+	drm->mode_config.max_width = xlnx_crtc_helper_get_max_width(crtc);
+	drm->mode_config.max_height = xlnx_crtc_helper_get_max_height(crtc);
+	drm->mode_config.cursor_width =
+		xlnx_crtc_helper_get_cursor_width(crtc);
+	drm->mode_config.cursor_height =
+		xlnx_crtc_helper_get_cursor_height(crtc);
+}
+
+static int xlnx_drm_open(struct drm_device *dev, struct drm_file *file)
+{
+	struct xlnx_drm *xlnx_drm = dev->dev_private;
+
+	/* This is a hacky way to allow the root user to run as a master */
+	if (!(drm_is_primary_client(file) && !dev->master) &&
+	    !file->is_master && capable(CAP_SYS_ADMIN)) {
+		file->is_master = 1;
+		xlnx_drm->master_count++;
+	}
+
+	return 0;
+}
+
+static int xlnx_drm_release(struct inode *inode, struct file *filp)
+{
+	struct drm_file *file = filp->private_data;
+	struct drm_minor *minor = file->minor;
+	struct drm_device *drm = minor->dev;
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+	if (file->is_master && xlnx_drm->master_count) {
+		xlnx_drm->master_count--;
+		file->is_master = 0;
+	}
+
+	return drm_release(inode, filp);
+}
+
+static void xlnx_lastclose(struct drm_device *drm)
+{
+	struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+	if (xlnx_drm->fb)
+		drm_fb_helper_restore_fbdev_mode_unlocked(xlnx_drm->fb);
+}
+
+static const struct file_operations xlnx_fops = {
+	.owner		= THIS_MODULE,
+	.open		= drm_open,
+	.release	= xlnx_drm_release,
+	.unlocked_ioctl	= drm_ioctl,
+	.mmap		= drm_gem_mmap,
+	.poll		= drm_poll,
+	.read		= drm_read,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl	= drm_compat_ioctl,
+#endif
+	.llseek		= noop_llseek,
+};
+
+static struct drm_driver xlnx_drm_driver = {
+	.driver_features		= DRIVER_MODESET | DRIVER_GEM |
+					  DRIVER_ATOMIC,
+	.open				= xlnx_drm_open,
+	.lastclose			= xlnx_lastclose,
+
+	DRM_GEM_CMA_DRIVER_OPS_VMAP_WITH_DUMB_CREATE(xlnx_gem_cma_dumb_create),
+
+	.fops				= &xlnx_fops,
+
+	.name				= DRIVER_NAME,
+	.desc				= DRIVER_DESC,
+	.date				= DRIVER_DATE,
+	.major				= DRIVER_MAJOR,
+	.minor				= DRIVER_MINOR,
+};
+
+static int xlnx_bind(struct device *dev)
+{
+	struct xlnx_drm *xlnx_drm;
+	struct drm_device *drm;
+	const struct drm_format_info *info;
+	struct platform_device *master = to_platform_device(dev);
+	struct platform_device *pdev = to_platform_device(dev->parent);
+	int ret;
+	u32 format;
+
+	drm = drm_dev_alloc(&xlnx_drm_driver, &pdev->dev);
+	if (IS_ERR(drm))
+		return PTR_ERR(drm);
+
+	xlnx_drm = devm_kzalloc(drm->dev, sizeof(*xlnx_drm), GFP_KERNEL);
+	if (!xlnx_drm) {
+		ret = -ENOMEM;
+		goto err_drm;
+	}
+
+	drm_mode_config_init(drm);
+	drm->mode_config.funcs = &xlnx_mode_config_funcs;
+
+	ret = drm_vblank_init(drm, MAX_CRTC);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to initialize vblank\n");
+		goto err_xlnx_drm;
+	}
+
+	drm->dev_private = xlnx_drm;
+	xlnx_drm->drm = drm;
+	xlnx_drm->master = master;
+	drm_kms_helper_poll_init(drm);
+	platform_set_drvdata(master, xlnx_drm);
+
+	xlnx_drm->crtc = xlnx_crtc_helper_init(drm);
+	if (IS_ERR(xlnx_drm->crtc)) {
+		ret = PTR_ERR(xlnx_drm->crtc);
+		goto err_xlnx_drm;
+	}
+
+	ret = component_bind_all(&master->dev, drm);
+	if (ret)
+		goto err_crtc;
+
+	xlnx_mode_config_init(drm);
+	drm_mode_config_reset(drm);
+	dma_set_mask(drm->dev, xlnx_crtc_helper_get_dma_mask(xlnx_drm->crtc));
+
+	format = xlnx_crtc_helper_get_format(xlnx_drm->crtc);
+	info = drm_format_info(format);
+	if (info && info->depth && info->cpp[0]) {
+		unsigned int align;
+
+		align = xlnx_crtc_helper_get_align(xlnx_drm->crtc);
+		xlnx_drm->fb = xlnx_fb_init(drm, info->cpp[0] * 8, 1, align,
+					    xlnx_fbdev_vres);
+		if (IS_ERR(xlnx_drm->fb)) {
+			dev_err(&pdev->dev,
+				"failed to initialize drm fb\n");
+			xlnx_drm->fb = NULL;
+		}
+	} else {
+		/* fbdev emulation is optional */
+		dev_info(&pdev->dev, "fbdev is not initialized\n");
+	}
+
+	ret = drm_dev_register(drm, 0);
+	if (ret < 0)
+		goto err_fb;
+
+	return 0;
+
+err_fb:
+	if (xlnx_drm->fb)
+		xlnx_fb_fini(xlnx_drm->fb);
+	component_unbind_all(drm->dev, drm);
+err_crtc:
+	xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
+err_xlnx_drm:
+	drm_mode_config_cleanup(drm);
+err_drm:
+	drm_dev_put(drm);
+	return ret;
+}
+
+static void xlnx_unbind(struct device *dev)
+{
+	struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
+	struct drm_device *drm = xlnx_drm->drm;
+
+	drm_dev_unregister(drm);
+	component_unbind_all(&xlnx_drm->master->dev, drm);
+	if (xlnx_drm->fb) {
+		xlnx_fb_fini(xlnx_drm->fb);
+		xlnx_drm->fb = NULL;
+	}
+	xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
+	drm_kms_helper_poll_fini(drm);
+	drm_mode_config_cleanup(drm);
+	drm_dev_put(drm);
+}
+
+static const struct component_master_ops xlnx_master_ops = {
+	.bind	= xlnx_bind,
+	.unbind	= xlnx_unbind,
+};
+
+static int xlnx_of_component_probe(struct device *master_dev,
+				   int (*compare_of)(struct device *, void *),
+				   const struct component_master_ops *m_ops)
+{
+	struct device *dev = master_dev->parent;
+	struct device_node *ep, *port, *remote, *parent;
+	struct component_match *match = NULL;
+	int i;
+
+	if (!dev->of_node)
+		return -EINVAL;
+
+	component_match_add(master_dev, &match, compare_of, dev->of_node);
+
+	for (i = 0; ; i++) {
+		port = of_parse_phandle(dev->of_node, "ports", i);
+		if (!port)
+			break;
+
+		parent = port->parent;
+		if (!of_node_cmp(parent->name, "ports"))
+			parent = parent->parent;
+		parent = of_node_get(parent);
+
+		if (!of_device_is_available(parent)) {
+			of_node_put(parent);
+			of_node_put(port);
+			continue;
+		}
+
+		component_match_add(master_dev, &match, compare_of, parent);
+		of_node_put(parent);
+		of_node_put(port);
+	}
+
+	parent = dev->of_node;
+	for (i = 0; ; i++) {
+		parent = of_node_get(parent);
+		if (!of_device_is_available(parent)) {
+			of_node_put(parent);
+			continue;
+		}
+
+		for_each_endpoint_of_node(parent, ep) {
+			remote = of_graph_get_remote_port_parent(ep);
+			if (!remote || !of_device_is_available(remote) ||
+			    remote == dev->of_node) {
+				of_node_put(remote);
+				continue;
+			} else if (!of_device_is_available(remote->parent)) {
+				dev_warn(dev, "parent dev of %s unavailable\n",
+					 remote->full_name);
+				of_node_put(remote);
+				continue;
+			}
+			component_match_add(master_dev, &match, compare_of,
+					    remote);
+			of_node_put(remote);
+		}
+		of_node_put(parent);
+
+		port = of_parse_phandle(dev->of_node, "ports", i);
+		if (!port)
+			break;
+
+		parent = port->parent;
+		if (!of_node_cmp(parent->name, "ports"))
+			parent = parent->parent;
+		of_node_put(port);
+	}
+
+	return component_master_add_with_match(master_dev, m_ops, match);
+}
+
+static int xlnx_compare_of(struct device *dev, void *data)
+{
+	return dev->of_node == data;
+}
+
+static int xlnx_platform_probe(struct platform_device *pdev)
+{
+	return xlnx_of_component_probe(&pdev->dev, xlnx_compare_of,
+				       &xlnx_master_ops);
+}
+
+static int xlnx_platform_remove(struct platform_device *pdev)
+{
+	component_master_del(&pdev->dev, &xlnx_master_ops);
+	return 0;
+}
+
+static void xlnx_platform_shutdown(struct platform_device *pdev)
+{
+	component_master_del(&pdev->dev, &xlnx_master_ops);
+}
+
+static int __maybe_unused xlnx_pm_suspend(struct device *dev)
+{
+	struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
+	struct drm_device *drm = xlnx_drm->drm;
+
+	drm_kms_helper_poll_disable(drm);
+
+	xlnx_drm->suspend_state = drm_atomic_helper_suspend(drm);
+	if (IS_ERR(xlnx_drm->suspend_state)) {
+		drm_kms_helper_poll_enable(drm);
+		return PTR_ERR(xlnx_drm->suspend_state);
+	}
+
+	return 0;
+}
+
+static int __maybe_unused xlnx_pm_resume(struct device *dev)
+{
+	struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
+	struct drm_device *drm = xlnx_drm->drm;
+
+	drm_atomic_helper_resume(drm, xlnx_drm->suspend_state);
+	drm_kms_helper_poll_enable(drm);
+
+	return 0;
+}
+
+static const struct dev_pm_ops xlnx_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xlnx_pm_suspend, xlnx_pm_resume)
+};
+
+static struct platform_driver xlnx_driver = {
+	.probe			= xlnx_platform_probe,
+	.remove			= xlnx_platform_remove,
+	.shutdown		= xlnx_platform_shutdown,
+	.driver			= {
+		.name		= "xlnx-drm",
+		.pm		= &xlnx_pm_ops,
+	},
+};
+
+/* bitmap for master id */
+static u32 xlnx_master_ids = GENMASK(31, 0);
+
+/**
+ * xlnx_drm_pipeline_init - Initialize the drm pipeline for the device
+ * @pdev: The platform device to initialize the drm pipeline device
+ *
+ * This function initializes the drm pipeline device, struct drm_device,
+ * on @pdev by creating a logical master platform device. The logical platform
+ * device acts as a master device to bind slave devices and represents
+ * the entire pipeline.
+ * The logical master uses the port bindings of the calling device to
+ * figure out the pipeline topology.
+ *
+ * Return: the logical master platform device if the drm device is initialized
+ * on @pdev. Error code otherwise.
+ */
+struct platform_device *xlnx_drm_pipeline_init(struct platform_device *pdev)
+{
+	struct platform_device *master;
+	int id, ret;
+
+	id = ffs(xlnx_master_ids);
+	if (!id)
+		return ERR_PTR(-ENOSPC);
+
+	master = platform_device_alloc("xlnx-drm", id - 1);
+	if (!master)
+		return ERR_PTR(-ENOMEM);
+
+	master->dev.parent = &pdev->dev;
+	ret = platform_device_add(master);
+	if (ret)
+		goto err_out;
+
+	WARN_ON(master->id != id - 1);
+	xlnx_master_ids &= ~BIT(master->id);
+	return master;
+
+err_out:
+	platform_device_unregister(master);
+	return ERR_PTR(ret);
+}
+EXPORT_SYMBOL_GPL(xlnx_drm_pipeline_init);
+
+/**
+ * xlnx_drm_pipeline_exit - Release the drm pipeline for the device
+ * @master: The master pipeline device to release
+ *
+ * Release the logical pipeline device returned by xlnx_drm_pipeline_init().
+ */
+void xlnx_drm_pipeline_exit(struct platform_device *master)
+{
+	xlnx_master_ids |= BIT(master->id);
+	platform_device_unregister(master);
+}
+EXPORT_SYMBOL_GPL(xlnx_drm_pipeline_exit);
+
+static int __init xlnx_drm_drv_init(void)
+{
+	xlnx_bridge_helper_init();
+	platform_driver_register(&xlnx_driver);
+	return 0;
+}
+
+static void __exit xlnx_drm_drv_exit(void)
+{
+	platform_driver_unregister(&xlnx_driver);
+	xlnx_bridge_helper_fini();
+}
+
+module_init(xlnx_drm_drv_init);
+module_exit(xlnx_drm_drv_exit);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx DRM KMS Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_drv.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx DRM KMS Header for Xilinx
+ *
+ *  Copyright (C) 2013 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyunk@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_DRV_H_
+#define _XLNX_DRV_H_
+
+struct drm_device;
+struct xlnx_crtc_helper;
+
+struct platform_device *xlnx_drm_pipeline_init(struct platform_device *parent);
+void xlnx_drm_pipeline_exit(struct platform_device *pipeline);
+
+uint32_t xlnx_get_format(struct drm_device *drm);
+unsigned int xlnx_get_align(struct drm_device *drm);
+struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm);
+struct xlnx_bridge_helper *xlnx_get_bridge_helper(struct drm_device *drm);
+
+#endif /* _XLNX_DRV_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_dsi.c
@@ -0,0 +1,1035 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA MIPI DSI Tx Controller driver.
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author : Saurabh Sengar <saurabhs@xilinx.com>
+ *        : Siva Rajesh J <siva.rajesh.jarugula@xilinx.com>
+ */
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_probe_helper.h>
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/device.h>
+#include <linux/iopoll.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <video/mipi_display.h>
+#include <video/videomode.h>
+
+#include "xlnx_bridge.h"
+
+/* DSI Tx IP registers */
+#define XDSI_CCR			0x00
+#define XDSI_CCR_COREENB		BIT(0)
+#define XDSI_CCR_SOFTRST		BIT(1)
+#define XDSI_CCR_CRREADY		BIT(2)
+#define XDSI_CCR_CMDMODE		BIT(3)
+#define XDSI_CCR_DFIFORST		BIT(4)
+#define XDSI_CCR_CMDFIFORST		BIT(5)
+#define XDSI_PCR			0x04
+#define XDSI_PCR_VIDEOMODE(x)		(((x) & 0x3) << 3)
+#define XDSI_PCR_VIDEOMODE_MASK		(0x3 << 3)
+#define XDSI_PCR_VIDEOMODE_SHIFT	3
+#define XDSI_PCR_BLLPTYPE(x)		((x) << 5)
+#define XDSI_PCR_BLLPMODE(x)		((x) << 6)
+#define XDSI_PCR_EOTPENABLE(x)		((x) << 13)
+#define XDSI_GIER			0x20
+#define XDSI_ISR			0x24
+#define XDSI_IER			0x28
+#define XDSI_STR			0x2C
+#define XDSI_STR_RDY_SHPKT		BIT(6)
+#define XDSI_STR_RDY_LNGPKT		BIT(7)
+#define XDSI_STR_DFIFO_FULL		BIT(8)
+#define XDSI_STR_DFIFO_EMPTY		BIT(9)
+#define XDSI_STR_WAITFR_DATA		BIT(10)
+#define XDSI_STR_CMD_EXE_PGS		BIT(11)
+#define XDSI_STR_CCMD_PROC		BIT(12)
+#define XDSI_STR_LPKT_MASK		(0x5 << 7)
+#define XDSI_CMD			0x30
+#define XDSI_CMD_QUEUE_PACKET(x)	((x) & GENMASK(23, 0))
+#define XDSI_DFR			0x34
+#define XDSI_TIME1			0x50
+#define XDSI_TIME1_BLLP_BURST(x)	((x) & GENMASK(15, 0))
+#define XDSI_TIME1_HSA(x)		(((x) & GENMASK(15, 0)) << 16)
+#define XDSI_TIME2			0x54
+#define XDSI_TIME2_VACT(x)		((x) & GENMASK(15, 0))
+#define XDSI_TIME2_HACT(x)		(((x) & GENMASK(15, 0)) << 16)
+#define XDSI_HACT_MULTIPLIER		GENMASK(1, 0)
+#define XDSI_TIME3			0x58
+#define XDSI_TIME3_HFP(x)		((x) & GENMASK(15, 0))
+#define XDSI_TIME3_HBP(x)		(((x) & GENMASK(15, 0)) << 16)
+#define XDSI_TIME4			0x5c
+#define XDSI_TIME4_VFP(x)		((x) & GENMASK(7, 0))
+#define XDSI_TIME4_VBP(x)		(((x) & GENMASK(7, 0)) << 8)
+#define XDSI_TIME4_VSA(x)		(((x) & GENMASK(7, 0)) << 16)
+#define XDSI_LTIME			0x60
+#define XDSI_BLLP_TIME			0x64
+/*
+ * XDSI_NUM_DATA_T represents number of data types in the
+ * enum mipi_dsi_pixel_format in the MIPI DSI part of DRM framework.
+ */
+#define XDSI_NUM_DATA_T			4
+#define XDSI_VIDEO_MODE_SYNC_PULSE	0x0
+#define XDSI_VIDEO_MODE_SYNC_EVENT	0x1
+#define XDSI_VIDEO_MODE_BURST		0x2
+
+#define XDSI_DPHY_CLK_MIN	197000000000UL
+#define XDSI_DPHY_CLK_MAX	203000000000UL
+#define XDSI_DPHY_CLK_REQ	200000000000UL
+
+/* command timeout in usec */
+#define XDSI_CMD_TIMEOUT_VAL	(3000)
+
+/**
+ * struct xlnx_dsi - Core configuration DSI Tx subsystem device structure
+ * @encoder: DRM encoder structure
+ * @dsi_host: DSI host device
+ * @connector: DRM connector structure
+ * @panel_node: MIPI DSI device panel node
+ * @panel:  DRM panel structure
+ * @dev: device structure
+ * @iomem: Base address of DSI subsystem
+ * @lanes: number of active data lanes supported by DSI controller
+ * @cmdmode: command mode support
+ * @mode_flags: DSI operation mode related flags
+ * @format: pixel format for video mode of DSI controller
+ * @vm: videomode data structure
+ * @mul_factor: multiplication factor for HACT timing parameter
+ * @eotp_prop: configurable EoTP DSI parameter
+ * @bllp_mode_prop: configurable BLLP mode DSI parameter
+ * @bllp_type_prop: configurable BLLP type DSI parameter
+ * @video_mode_prop: configurable Video mode DSI parameter
+ * @bllp_burst_time_prop: Configurable BLLP time for burst mode
+ * @cmd_queue_prop: configurable command queue
+ * @eotp_prop_val: configurable EoTP DSI parameter value
+ * @bllp_mode_prop_val: configurable BLLP mode DSI parameter value
+ * @bllp_type_prop_val: configurable BLLP type DSI parameter value
+ * @video_mode_prop_val: configurable Video mode DSI parameter value
+ * @bllp_burst_time_prop_val: Configurable BLLP time for burst mode value
+ * @cmd_queue_prop_val: configurable command queue value
+ * @bridge: bridge structure
+ * @height_out: configurable bridge output height parameter
+ * @height_out_prop_val: configurable bridge output height parameter value
+ * @width_out: configurable bridge output width parameter
+ * @width_out_prop_val: configurable bridge output width parameter value
+ * @in_fmt: configurable bridge input media format
+ * @in_fmt_prop_val: configurable media bus format value
+ * @out_fmt: configurable bridge output media format
+ * @out_fmt_prop_val: configurable media bus format value
+ * @video_aclk: Video clock
+ * @dphy_clk_200M: 200MHz DPHY clock and AXI Lite clock
+ */
+struct xlnx_dsi {
+	struct drm_encoder encoder;
+	struct mipi_dsi_host dsi_host;
+	struct drm_connector connector;
+	struct device_node *panel_node;
+	struct drm_panel *panel;
+	struct device *dev;
+	void __iomem *iomem;
+	u32 lanes;
+	bool cmdmode;
+	u32 mode_flags;
+	enum mipi_dsi_pixel_format format;
+	struct videomode vm;
+	u32 mul_factor;
+	struct drm_property *eotp_prop;
+	struct drm_property *bllp_mode_prop;
+	struct drm_property *bllp_type_prop;
+	struct drm_property *video_mode_prop;
+	struct drm_property *bllp_burst_time_prop;
+	struct drm_property *cmd_queue_prop;
+	bool eotp_prop_val;
+	bool bllp_mode_prop_val;
+	bool bllp_type_prop_val;
+	u32 video_mode_prop_val;
+	u32 bllp_burst_time_prop_val;
+	u32 cmd_queue_prop_val;
+	struct xlnx_bridge *bridge;
+	struct drm_property *height_out;
+	u32 height_out_prop_val;
+	struct drm_property *width_out;
+	u32 width_out_prop_val;
+	struct drm_property *in_fmt;
+	u32 in_fmt_prop_val;
+	struct drm_property *out_fmt;
+	u32 out_fmt_prop_val;
+	struct clk *video_aclk;
+	struct clk *dphy_clk_200M;
+};
+
+#define host_to_dsi(host) container_of(host, struct xlnx_dsi, dsi_host)
+#define connector_to_dsi(c) container_of(c, struct xlnx_dsi, connector)
+#define encoder_to_dsi(e) container_of(e, struct xlnx_dsi, encoder)
+
+static inline void xlnx_dsi_writel(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static inline u32 xlnx_dsi_readl(void __iomem *base, int offset)
+{
+	return readl(base + offset);
+}
+
+/**
+ * xlnx_dsi_set_config_parameters - Configure DSI Tx registers with parameters
+ * given from user application.
+ * @dsi: DSI structure having the updated user parameters
+ *
+ * This function takes the DSI structure having drm_property parameters
+ * configured from  user application and writes them into DSI IP registers.
+ */
+static void xlnx_dsi_set_config_parameters(struct xlnx_dsi *dsi)
+{
+	u32 reg;
+
+	reg = XDSI_PCR_EOTPENABLE(dsi->eotp_prop_val);
+	reg |= XDSI_PCR_VIDEOMODE(dsi->video_mode_prop_val);
+	reg |= XDSI_PCR_BLLPTYPE(dsi->bllp_type_prop_val);
+	reg |= XDSI_PCR_BLLPMODE(dsi->bllp_mode_prop_val);
+
+	xlnx_dsi_writel(dsi->iomem, XDSI_PCR, reg);
+	/*
+	 * Configure the burst time if video mode is burst.
+	 * HSA of TIME1 register is ignored in this mode.
+	 */
+	if (dsi->video_mode_prop_val == XDSI_VIDEO_MODE_BURST) {
+		reg = XDSI_TIME1_BLLP_BURST(dsi->bllp_burst_time_prop_val);
+		xlnx_dsi_writel(dsi->iomem, XDSI_TIME1, reg);
+	}
+
+	reg = XDSI_CMD_QUEUE_PACKET(dsi->cmd_queue_prop_val);
+	xlnx_dsi_writel(dsi->iomem, XDSI_CMD, reg);
+
+	dev_dbg(dsi->dev, "PCR register value is = %x\n",
+		xlnx_dsi_readl(dsi->iomem, XDSI_PCR));
+}
+
+/**
+ * xlnx_dsi_set_display_mode - Configure DSI timing registers
+ * @dsi: DSI structure having the updated user parameters
+ *
+ * This function writes the timing parameters of DSI IP which are
+ * retrieved from panel timing values.
+ */
+static void xlnx_dsi_set_display_mode(struct xlnx_dsi *dsi)
+{
+	struct videomode *vm = &dsi->vm;
+	u32 reg, video_mode;
+
+	reg = xlnx_dsi_readl(dsi->iomem, XDSI_PCR);
+	video_mode = (reg & XDSI_PCR_VIDEOMODE_MASK) >>
+		      XDSI_PCR_VIDEOMODE_SHIFT;
+
+	/* configure the HSA value only if non_burst_sync_pluse video mode */
+	if (!video_mode &&
+	    (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)) {
+		reg = XDSI_TIME1_HSA(vm->hsync_len);
+		xlnx_dsi_writel(dsi->iomem, XDSI_TIME1, reg);
+	}
+
+	reg = XDSI_TIME4_VFP(vm->vfront_porch) |
+	      XDSI_TIME4_VBP(vm->vback_porch) |
+	      XDSI_TIME4_VSA(vm->vsync_len);
+	xlnx_dsi_writel(dsi->iomem, XDSI_TIME4, reg);
+
+	reg = XDSI_TIME3_HFP(vm->hfront_porch) |
+	      XDSI_TIME3_HBP(vm->hback_porch);
+	xlnx_dsi_writel(dsi->iomem, XDSI_TIME3, reg);
+
+	dev_dbg(dsi->dev, "mul factor for parsed datatype is = %d\n",
+		(dsi->mul_factor) / 100);
+	/*
+	 * The HACT parameter received from panel timing values should be
+	 * divisible by 4. The reason for this is, the word count given as
+	 * input to DSI controller is HACT * mul_factor. The mul_factor is
+	 * 3, 2.25, 2.25, 2 respectively for RGB888, RGB666_L, RGB666_P and
+	 * RGB565.
+	 * e.g. for RGB666_L color format and 1080p, the word count is
+	 * 1920*2.25 = 4320 which is divisible by 4 and it is a valid input
+	 * to DSI controller. Based on this 2.25 mul factor, we come up with
+	 * the division factor of (XDSI_HACT_MULTIPLIER) as 4 for checking
+	 */
+	if ((vm->hactive & XDSI_HACT_MULTIPLIER) != 0)
+		dev_warn(dsi->dev, "Incorrect HACT will be programmed\n");
+
+	reg = XDSI_TIME2_HACT((vm->hactive) * (dsi->mul_factor) / 100) |
+	      XDSI_TIME2_VACT(vm->vactive);
+	xlnx_dsi_writel(dsi->iomem, XDSI_TIME2, reg);
+
+	dev_dbg(dsi->dev, "LCD size = %dx%d\n", vm->hactive, vm->vactive);
+}
+
+/**
+ * xlnx_dsi_set_display_enable - Enables the DSI Tx IP core enable
+ * register bit
+ * @dsi: DSI structure having the updated user parameters
+ *
+ * This function takes the DSI strucure and enables the core enable bit
+ * of core configuration register.
+ */
+static void xlnx_dsi_set_display_enable(struct xlnx_dsi *dsi)
+{
+	u32 reg;
+
+	reg = xlnx_dsi_readl(dsi->iomem, XDSI_CCR);
+	reg |= XDSI_CCR_COREENB;
+
+	xlnx_dsi_writel(dsi->iomem, XDSI_CCR, reg);
+	dev_dbg(dsi->dev, "MIPI DSI Tx controller is enabled.\n");
+}
+
+/**
+ * xlnx_dsi_set_display_disable - Disable the DSI Tx IP core enable
+ * register bit
+ * @dsi: DSI structure having the updated user parameters
+ *
+ * This function takes the DSI strucure and disables the core enable bit
+ * of core configuration register.
+ */
+static void xlnx_dsi_set_display_disable(struct xlnx_dsi *dsi)
+{
+	u32 reg;
+
+	reg = xlnx_dsi_readl(dsi->iomem, XDSI_CCR);
+	reg &= ~XDSI_CCR_COREENB;
+
+	xlnx_dsi_writel(dsi->iomem, XDSI_CCR, reg);
+	dev_dbg(dsi->dev, "DSI Tx is disabled. reset regs to default values\n");
+}
+
+/**
+ * xlnx_dsi_atomic_set_property - implementation of drm_connector_funcs
+ * set_property invoked by IOCTL call to DRM_IOCTL_MODE_OBJ_SETPROPERTY
+ *
+ * @connector: pointer Xilinx DSI connector
+ * @state: DRM connector state
+ * @prop: pointer to the drm_property structure
+ * @val: DSI parameter value that is configured from user application
+ *
+ * This function takes a drm_property name and value given from user application
+ * and update the DSI structure property varabiles with the values.
+ * These values are later used to configure the DSI Rx IP.
+ *
+ * Return: 0 on success OR -EINVAL if setting property fails
+ */
+static int xlnx_dsi_atomic_set_property(struct drm_connector *connector,
+					struct drm_connector_state *state,
+					struct drm_property *prop, u64 val)
+{
+	struct xlnx_dsi *dsi = connector_to_dsi(connector);
+
+	dev_dbg(dsi->dev, "property name = %s, value = %lld\n",
+		prop->name, val);
+
+	if (prop == dsi->eotp_prop)
+		dsi->eotp_prop_val = !!val;
+	else if (prop == dsi->bllp_mode_prop)
+		dsi->bllp_mode_prop_val = !!val;
+	else if (prop == dsi->bllp_type_prop)
+		dsi->bllp_type_prop_val = !!val;
+	else if (prop == dsi->video_mode_prop)
+		dsi->video_mode_prop_val = (unsigned int)val;
+	else if (prop == dsi->bllp_burst_time_prop)
+		dsi->bllp_burst_time_prop_val = (unsigned int)val;
+	else if (prop == dsi->cmd_queue_prop)
+		dsi->cmd_queue_prop_val = (unsigned int)val;
+	else if (prop == dsi->height_out)
+		dsi->height_out_prop_val = (u32)val;
+	else if (prop == dsi->width_out)
+		dsi->width_out_prop_val = (u32)val;
+	else if (prop == dsi->in_fmt)
+		dsi->in_fmt_prop_val = (u32)val;
+	else if (prop == dsi->out_fmt)
+		dsi->out_fmt_prop_val = (u32)val;
+	else
+		return -EINVAL;
+
+	xlnx_dsi_set_config_parameters(dsi);
+
+	return 0;
+}
+
+static int
+xlnx_dsi_atomic_get_property(struct drm_connector *connector,
+			     const struct drm_connector_state *state,
+			     struct drm_property *prop, uint64_t *val)
+{
+	struct xlnx_dsi *dsi = connector_to_dsi(connector);
+
+	if (prop == dsi->eotp_prop)
+		*val = dsi->eotp_prop_val;
+	else if (prop == dsi->bllp_mode_prop)
+		*val = dsi->bllp_mode_prop_val;
+	else if (prop == dsi->bllp_type_prop)
+		*val = dsi->bllp_type_prop_val;
+	else if (prop == dsi->video_mode_prop)
+		*val = dsi->video_mode_prop_val;
+	else if (prop == dsi->bllp_burst_time_prop)
+		*val = dsi->bllp_burst_time_prop_val;
+	else if (prop == dsi->cmd_queue_prop)
+		*val = dsi->cmd_queue_prop_val;
+	else if (prop == dsi->height_out)
+		*val = dsi->height_out_prop_val;
+	else if (prop == dsi->width_out)
+		*val = dsi->width_out_prop_val;
+	else if (prop == dsi->in_fmt)
+		*val = dsi->in_fmt_prop_val;
+	else if (prop == dsi->out_fmt)
+		*val = dsi->out_fmt_prop_val;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * xlnx_dsi_host_transfer - transfer command to panel
+ * @host: mipi dsi host structure
+ * @msg: mipi dsi msg with type, length and data
+ *
+ * This function is valid only in command mode.
+ * It checks the command fifo empty status and writes into
+ * data or cmd register and waits for the completion status.
+ *
+ * Return:	number of bytes, on success and error number on failure
+ */
+static ssize_t xlnx_dsi_host_transfer(struct mipi_dsi_host *host,
+				      const struct mipi_dsi_msg *msg)
+{
+	struct xlnx_dsi *dsi = host_to_dsi(host);
+	u32 data0, data1, cmd0, val, offset;
+	int status;
+	const char *tx_buf = msg->tx_buf;
+
+	switch (msg->type) {
+	case MIPI_DSI_DCS_LONG_WRITE:
+		status = readl_poll_timeout(dsi->iomem + XDSI_STR, val,
+					    (val & XDSI_STR_LPKT_MASK) ==
+					     XDSI_STR_LPKT_MASK, 1,
+					    XDSI_CMD_TIMEOUT_VAL);
+		if (status) {
+			dev_err(dsi->dev, "long cmd fifo not empty!\n");
+			return -ETIMEDOUT;
+		}
+		data0 = tx_buf[0] | (tx_buf[1] << 8) | (tx_buf[2] << 16) |
+			(tx_buf[3] << 24);
+		data1 = tx_buf[4] | (tx_buf[5] << 8);
+		cmd0 = msg->type | (MIPI_DSI_DCS_READ << 8);
+
+		xlnx_dsi_writel(dsi->iomem, XDSI_DFR, data0);
+		xlnx_dsi_writel(dsi->iomem, XDSI_DFR, data1);
+		xlnx_dsi_writel(dsi->iomem, XDSI_CMD, cmd0);
+		break;
+	case MIPI_DSI_GENERIC_LONG_WRITE:
+		status = readl_poll_timeout(dsi->iomem + XDSI_STR, val,
+					    (val & XDSI_STR_LPKT_MASK) ==
+					    XDSI_STR_LPKT_MASK, 1,
+					    XDSI_CMD_TIMEOUT_VAL);
+		if (status) {
+			dev_err(dsi->dev, "long cmd fifo not empty!\n");
+			return -EBUSY;
+		}
+		cmd0 = msg->type | (msg->tx_len << 8);
+		xlnx_dsi_writel(dsi->iomem, XDSI_CMD, cmd0);
+
+		for (offset = 0; offset <= msg->tx_len; offset += 4) {
+			data0 = tx_buf[0 + offset] | tx_buf[1 + offset] << 8 |
+				tx_buf[2 + offset] << 16 |
+				tx_buf[3 + offset] << 24;
+			xlnx_dsi_writel(dsi->iomem, XDSI_DFR, data0);
+		}
+		break;
+	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
+		status = readl_poll_timeout(dsi->iomem + XDSI_STR, val,
+					    (val & XDSI_STR_RDY_SHPKT) ==
+					    XDSI_STR_RDY_SHPKT, 1,
+					    XDSI_CMD_TIMEOUT_VAL);
+		if (status) {
+			dev_err(dsi->dev, "short cmd fifo not empty\n");
+			return -EBUSY;
+		}
+		data0 = MIPI_DSI_DCS_SHORT_WRITE_PARAM |
+			(tx_buf[0] << 8) | (tx_buf[1] << 16);
+		xlnx_dsi_writel(dsi->iomem, XDSI_CMD, data0);
+		break;
+	case MIPI_DSI_DCS_SHORT_WRITE:
+		status = readl_poll_timeout(dsi->iomem + XDSI_STR, val,
+					    (val & XDSI_STR_RDY_SHPKT) ==
+					    XDSI_STR_RDY_SHPKT, 1,
+					    XDSI_CMD_TIMEOUT_VAL);
+		if (status) {
+			dev_err(dsi->dev, "short cmd fifo not empty\n");
+			return -EBUSY;
+		}
+		data0 = MIPI_DSI_DCS_SHORT_WRITE | (tx_buf[0] << 8);
+		xlnx_dsi_writel(dsi->iomem, XDSI_CMD, data0);
+		break;
+	default:
+		dev_err(dsi->dev, "Unsupported command type\n");
+		return -EINVAL;
+	}
+
+	status = readl_poll_timeout(dsi->iomem + XDSI_STR, val,
+				    !(val & XDSI_STR_CMD_EXE_PGS), 1,
+				    XDSI_CMD_TIMEOUT_VAL);
+	if (status) {
+		dev_err(dsi->dev, "cmd timeout\n");
+		return status;
+	}
+
+	return msg->tx_len;
+}
+
+static int xlnx_dsi_host_attach(struct mipi_dsi_host *host,
+				struct mipi_dsi_device *device)
+{
+	u32 panel_lanes;
+	struct xlnx_dsi *dsi = host_to_dsi(host);
+
+	panel_lanes = device->lanes;
+	dsi->mode_flags = device->mode_flags;
+	dsi->panel_node = device->dev.of_node;
+
+	if (panel_lanes != dsi->lanes) {
+		dev_err(dsi->dev, "Mismatch of lanes. panel = %d, DSI = %d\n",
+			panel_lanes, dsi->lanes);
+		return -EINVAL;
+	}
+
+	if (dsi->lanes > 4 || dsi->lanes < 1) {
+		dev_err(dsi->dev, "%d lanes : invalid xlnx,dsi-num-lanes\n",
+			dsi->lanes);
+		return -EINVAL;
+	}
+
+	if (device->format != dsi->format) {
+		dev_err(dsi->dev, "Mismatch of format. panel = %d, DSI = %d\n",
+			device->format, dsi->format);
+		return -EINVAL;
+	}
+
+	if (dsi->connector.dev)
+		drm_helper_hpd_irq_event(dsi->connector.dev);
+
+	return 0;
+}
+
+static int xlnx_dsi_host_detach(struct mipi_dsi_host *host,
+				struct mipi_dsi_device *device)
+{
+	struct xlnx_dsi *dsi = host_to_dsi(host);
+
+	dsi->panel = NULL;
+
+	if (dsi->connector.dev)
+		drm_helper_hpd_irq_event(dsi->connector.dev);
+
+	return 0;
+}
+
+static const struct mipi_dsi_host_ops xlnx_dsi_ops = {
+	.attach = xlnx_dsi_host_attach,
+	.detach = xlnx_dsi_host_detach,
+	.transfer = xlnx_dsi_host_transfer,
+};
+
+static int xlnx_dsi_connector_dpms(struct drm_connector *connector, int mode)
+{
+	struct xlnx_dsi *dsi = connector_to_dsi(connector);
+	int ret;
+
+	dev_dbg(dsi->dev, "connector dpms state: %d\n", mode);
+
+	switch (mode) {
+	case DRM_MODE_DPMS_ON:
+		ret = drm_panel_prepare(dsi->panel);
+		if (ret < 0) {
+			dev_err(dsi->dev, "DRM panel not found\n");
+			return ret;
+		}
+
+		ret = drm_panel_enable(dsi->panel);
+		if (ret < 0) {
+			drm_panel_unprepare(dsi->panel);
+			dev_err(dsi->dev, "DRM panel not enabled\n");
+			return ret;
+		}
+		break;
+	default:
+		drm_panel_disable(dsi->panel);
+		drm_panel_unprepare(dsi->panel);
+		break;
+	}
+
+	return drm_helper_connector_dpms(connector, mode);
+}
+
+static enum drm_connector_status
+xlnx_dsi_detect(struct drm_connector *connector, bool force)
+{
+	struct xlnx_dsi *dsi = connector_to_dsi(connector);
+
+	if (!dsi->panel) {
+		dsi->panel = of_drm_find_panel(dsi->panel_node);
+		if (dsi->panel) {
+			if (dsi->cmdmode) {
+				xlnx_dsi_writel(dsi->iomem, XDSI_CCR,
+						XDSI_CCR_CMDMODE |
+						XDSI_CCR_COREENB);
+				drm_panel_prepare(dsi->panel);
+				xlnx_dsi_writel(dsi->iomem, XDSI_CCR, 0);
+			}
+		}
+	} else if (!dsi->panel_node) {
+		xlnx_dsi_connector_dpms(connector, DRM_MODE_DPMS_OFF);
+		dsi->panel = NULL;
+	}
+
+	if (dsi->panel)
+		return connector_status_connected;
+
+	return connector_status_disconnected;
+}
+
+static void xlnx_dsi_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+	connector->dev = NULL;
+}
+
+static const struct drm_connector_funcs xlnx_dsi_connector_funcs = {
+	.dpms = xlnx_dsi_connector_dpms,
+	.detect = xlnx_dsi_detect,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.destroy = xlnx_dsi_connector_destroy,
+	.atomic_set_property = xlnx_dsi_atomic_set_property,
+	.atomic_get_property = xlnx_dsi_atomic_get_property,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+	.reset			= drm_atomic_helper_connector_reset,
+};
+
+static int xlnx_dsi_get_modes(struct drm_connector *connector)
+{
+	struct xlnx_dsi *dsi = connector_to_dsi(connector);
+
+	if (dsi->panel)
+		return dsi->panel->funcs->get_modes(dsi->panel, connector);
+
+	return 0;
+}
+
+static struct drm_encoder *
+xlnx_dsi_best_encoder(struct drm_connector *connector)
+{
+	return &(connector_to_dsi(connector)->encoder);
+}
+
+static struct drm_connector_helper_funcs xlnx_dsi_connector_helper_funcs = {
+	.get_modes = xlnx_dsi_get_modes,
+	.best_encoder = xlnx_dsi_best_encoder,
+};
+
+/**
+ * xlnx_dsi_connector_create_property -  create DSI connector properties
+ *
+ * @connector: pointer to Xilinx DSI connector
+ *
+ * This function takes the xilinx DSI connector component and defines
+ * the drm_property variables with their default values.
+ */
+static void xlnx_dsi_connector_create_property(struct drm_connector *connector)
+{
+	struct drm_device *dev = connector->dev;
+	struct xlnx_dsi *dsi  = connector_to_dsi(connector);
+
+	dsi->eotp_prop = drm_property_create_bool(dev, 0, "eotp");
+	dsi->video_mode_prop = drm_property_create_range(dev, 0, "video_mode",
+							 0, 2);
+	dsi->bllp_mode_prop = drm_property_create_bool(dev, 0, "bllp_mode");
+	dsi->bllp_type_prop = drm_property_create_bool(dev, 0, "bllp_type");
+	dsi->bllp_burst_time_prop =
+		drm_property_create_range(dev, 0, "bllp_burst_time", 0, 0xFFFF);
+	dsi->cmd_queue_prop = drm_property_create_range(dev, 0, "cmd_queue", 0,
+							0xffffff);
+	dsi->height_out = drm_property_create_range(dev, 0, "height_out",
+						    2, 4096);
+	dsi->width_out = drm_property_create_range(dev, 0, "width_out",
+						   2, 4096);
+	dsi->in_fmt = drm_property_create_range(dev, 0, "in_fmt", 0, 16384);
+	dsi->out_fmt = drm_property_create_range(dev, 0, "out_fmt", 0, 16384);
+}
+
+/**
+ * xlnx_dsi_connector_attach_property -  attach DSI connector
+ * properties
+ *
+ * @connector: pointer to Xilinx DSI connector
+ */
+static void xlnx_dsi_connector_attach_property(struct drm_connector *connector)
+{
+	struct xlnx_dsi *dsi = connector_to_dsi(connector);
+	struct drm_mode_object *obj = &connector->base;
+
+	if (dsi->eotp_prop)
+		drm_object_attach_property(obj, dsi->eotp_prop, 1);
+
+	if (dsi->video_mode_prop)
+		drm_object_attach_property(obj, dsi->video_mode_prop, 0);
+
+	if (dsi->bllp_burst_time_prop)
+		drm_object_attach_property(&connector->base,
+					   dsi->bllp_burst_time_prop, 0);
+
+	if (dsi->bllp_mode_prop)
+		drm_object_attach_property(&connector->base,
+					   dsi->bllp_mode_prop, 0);
+
+	if (dsi->bllp_type_prop)
+		drm_object_attach_property(&connector->base,
+					   dsi->bllp_type_prop, 0);
+
+	if (dsi->cmd_queue_prop)
+		drm_object_attach_property(&connector->base,
+					   dsi->cmd_queue_prop, 0);
+
+	if (dsi->height_out)
+		drm_object_attach_property(obj, dsi->height_out, 0);
+
+	if (dsi->width_out)
+		drm_object_attach_property(obj, dsi->width_out, 0);
+
+	if (dsi->in_fmt)
+		drm_object_attach_property(obj, dsi->in_fmt, 0);
+
+	if (dsi->out_fmt)
+		drm_object_attach_property(obj, dsi->out_fmt, 0);
+}
+
+static int xlnx_dsi_create_connector(struct drm_encoder *encoder)
+{
+	struct xlnx_dsi *dsi = encoder_to_dsi(encoder);
+	struct drm_connector *connector = &dsi->connector;
+	int ret;
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+
+	ret = drm_connector_init(encoder->dev, connector,
+				 &xlnx_dsi_connector_funcs,
+				 DRM_MODE_CONNECTOR_DSI);
+	if (ret) {
+		dev_err(dsi->dev, "Failed to initialize connector with drm\n");
+		return ret;
+	}
+
+	drm_connector_helper_add(connector, &xlnx_dsi_connector_helper_funcs);
+	drm_connector_register(connector);
+	drm_connector_attach_encoder(connector, encoder);
+	xlnx_dsi_connector_create_property(connector);
+	xlnx_dsi_connector_attach_property(connector);
+
+	return 0;
+}
+
+/**
+ * xlnx_dsi_atomic_mode_set -  derive the DSI timing parameters
+ *
+ * @encoder: pointer to Xilinx DRM encoder
+ * @crtc_state: Pointer to drm core crtc state
+ * @connector_state: DSI connector drm state
+ *
+ * This function derives the DSI IP timing parameters from the timing
+ * values given in the attached panel driver.
+ */
+static void
+xlnx_dsi_atomic_mode_set(struct drm_encoder *encoder,
+			 struct drm_crtc_state *crtc_state,
+				 struct drm_connector_state *connector_state)
+{
+	struct xlnx_dsi *dsi = encoder_to_dsi(encoder);
+	struct videomode *vm = &dsi->vm;
+	struct drm_display_mode *m = &crtc_state->adjusted_mode;
+
+	/* Set bridge input and output parameters */
+	xlnx_bridge_set_input(dsi->bridge, m->hdisplay, m->vdisplay,
+			      dsi->in_fmt_prop_val);
+	xlnx_bridge_set_output(dsi->bridge, dsi->width_out_prop_val,
+			       dsi->height_out_prop_val,
+			       dsi->out_fmt_prop_val);
+	xlnx_bridge_enable(dsi->bridge);
+
+	vm->hactive = m->hdisplay;
+	vm->vactive = m->vdisplay;
+	vm->vfront_porch = m->vsync_start - m->vdisplay;
+	vm->vback_porch = m->vtotal - m->vsync_end;
+	vm->vsync_len = m->vsync_end - m->vsync_start;
+	vm->hfront_porch = m->hsync_start - m->hdisplay;
+	vm->hback_porch = m->htotal - m->hsync_end;
+	vm->hsync_len = m->hsync_end - m->hsync_start;
+	xlnx_dsi_set_display_mode(dsi);
+}
+
+static void xlnx_dsi_disable(struct drm_encoder *encoder)
+{
+	struct xlnx_dsi *dsi = encoder_to_dsi(encoder);
+
+	if (dsi->bridge)
+		xlnx_bridge_disable(dsi->bridge);
+
+	xlnx_dsi_set_display_disable(dsi);
+}
+
+static void xlnx_dsi_enable(struct drm_encoder *encoder)
+{
+	struct xlnx_dsi *dsi = encoder_to_dsi(encoder);
+
+	xlnx_dsi_set_display_enable(dsi);
+}
+
+static const struct drm_encoder_helper_funcs xlnx_dsi_encoder_helper_funcs = {
+	.atomic_mode_set = xlnx_dsi_atomic_mode_set,
+	.enable = xlnx_dsi_enable,
+	.disable = xlnx_dsi_disable,
+};
+
+static const struct drm_encoder_funcs xlnx_dsi_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+static int xlnx_dsi_parse_dt(struct xlnx_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+	struct device_node *node = dev->of_node;
+	int ret;
+	u32 datatype;
+	static const int xdsi_mul_fact[XDSI_NUM_DATA_T] = {300, 225, 225, 200};
+
+	dsi->dphy_clk_200M = devm_clk_get(dev, "dphy_clk_200M");
+	if (IS_ERR(dsi->dphy_clk_200M)) {
+		ret = PTR_ERR(dsi->dphy_clk_200M);
+		dev_err(dev, "failed to get dphy_clk_200M %d\n", ret);
+		return ret;
+	}
+
+	dsi->video_aclk = devm_clk_get(dev, "s_axis_aclk");
+	if (IS_ERR(dsi->video_aclk)) {
+		ret = PTR_ERR(dsi->video_aclk);
+		dev_err(dev, "failed to get video_clk %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * Used as a multiplication factor for HACT based on used
+	 * DSI data type.
+	 *
+	 * e.g. for RGB666_L datatype and 1920x1080 resolution,
+	 * the Hact (WC) would be as follows -
+	 * 1920 pixels * 18 bits per pixel / 8 bits per byte
+	 * = 1920 pixels * 2.25 bytes per pixel = 4320 bytes.
+	 *
+	 * Data Type - Multiplication factor
+	 * RGB888    - 3
+	 * RGB666_L  - 2.25
+-	 * RGB666_P  - 2.25
+	 * RGB565    - 2
+	 *
+	 * Since the multiplication factor maybe a floating number,
+	 * a 100x multiplication factor is used.
+	 */
+	ret = of_property_read_u32(node, "xlnx,dsi-num-lanes", &dsi->lanes);
+	if (ret < 0) {
+		dev_err(dsi->dev, "missing xlnx,dsi-num-lanes property\n");
+		return ret;
+	}
+	if (dsi->lanes > 4 || dsi->lanes < 1) {
+		dev_err(dsi->dev, "%d lanes : invalid lanes\n", dsi->lanes);
+		return -EINVAL;
+	}
+	ret = of_property_read_u32(node, "xlnx,dsi-data-type", &datatype);
+	if (ret < 0) {
+		dev_err(dsi->dev, "missing xlnx,dsi-data-type property\n");
+		return ret;
+	}
+	dsi->format = datatype;
+	if (datatype > MIPI_DSI_FMT_RGB565) {
+		dev_err(dsi->dev, "Invalid xlnx,dsi-data-type string\n");
+		return -EINVAL;
+	}
+	dsi->mul_factor = xdsi_mul_fact[datatype];
+
+	dsi->cmdmode = of_property_read_bool(node, "xlnx,dsi-cmd-mode");
+
+	dev_dbg(dsi->dev, "DSI controller num lanes = %d", dsi->lanes);
+	dev_dbg(dsi->dev, "DSI controller datatype = %d\n", datatype);
+	dev_dbg(dsi->dev, "DSI controller cmd mode = %d\n", dsi->cmdmode);
+
+	return 0;
+}
+
+static int xlnx_dsi_bind(struct device *dev, struct device *master,
+			 void *data)
+{
+	struct xlnx_dsi *dsi = dev_get_drvdata(dev);
+	struct drm_encoder *encoder = &dsi->encoder;
+	struct drm_device *drm_dev = data;
+	int ret;
+
+	/*
+	 * TODO: The possible CRTCs are 1 now as per current implementation of
+	 * DSI tx drivers. DRM framework can support more than one CRTCs and
+	 * DSI driver can be enhanced for that.
+	 */
+	encoder->possible_crtcs = 1;
+	drm_encoder_init(drm_dev, encoder, &xlnx_dsi_encoder_funcs,
+			 DRM_MODE_ENCODER_DSI, NULL);
+	drm_encoder_helper_add(encoder, &xlnx_dsi_encoder_helper_funcs);
+	ret = xlnx_dsi_create_connector(encoder);
+	if (ret) {
+		dev_err(dsi->dev, "fail creating connector, ret = %d\n", ret);
+		drm_encoder_cleanup(encoder);
+		return ret;
+	}
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		xlnx_dsi_connector_destroy(&dsi->connector);
+		drm_encoder_cleanup(encoder);
+		return ret;
+	}
+	return 0;
+}
+
+static void xlnx_dsi_unbind(struct device *dev, struct device *master,
+			    void *data)
+{
+	struct xlnx_dsi *dsi = dev_get_drvdata(dev);
+
+	xlnx_dsi_disable(&dsi->encoder);
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+	xlnx_bridge_disable(dsi->bridge);
+}
+
+static const struct component_ops xlnx_dsi_component_ops = {
+	.bind	= xlnx_dsi_bind,
+	.unbind	= xlnx_dsi_unbind,
+};
+
+static int xlnx_dsi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct xlnx_dsi *dsi;
+	struct device_node *vpss_node;
+	int ret;
+	unsigned long rate;
+
+	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+	if (!dsi)
+		return -ENOMEM;
+
+	dsi->dsi_host.ops = &xlnx_dsi_ops;
+	dsi->dsi_host.dev = dev;
+	dsi->dev = dev;
+
+	ret = xlnx_dsi_parse_dt(dsi);
+	if (ret)
+		return ret;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	dsi->iomem = devm_ioremap_resource(dev, res);
+	if (IS_ERR(dsi->iomem))
+		return PTR_ERR(dsi->iomem);
+
+	platform_set_drvdata(pdev, dsi);
+
+	/* Bridge support */
+	vpss_node = of_parse_phandle(dsi->dev->of_node, "xlnx,vpss", 0);
+	if (vpss_node) {
+		dsi->bridge = of_xlnx_bridge_get(vpss_node);
+		if (!dsi->bridge) {
+			dev_info(dsi->dev, "Didn't get bridge instance\n");
+			return -EPROBE_DEFER;
+		}
+	}
+
+	ret = clk_set_rate(dsi->dphy_clk_200M, XDSI_DPHY_CLK_REQ);
+	if (ret) {
+		dev_err(dev, "failed to set dphy clk rate %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(dsi->dphy_clk_200M);
+	if (ret) {
+		dev_err(dev, "failed to enable dphy clk %d\n", ret);
+		return ret;
+	}
+
+	rate = clk_get_rate(dsi->dphy_clk_200M);
+	if (rate < XDSI_DPHY_CLK_MIN && rate > XDSI_DPHY_CLK_MAX) {
+		dev_err(dev, "Error DPHY clock = %lu\n", rate);
+		ret = -EINVAL;
+		goto err_disable_dphy_clk;
+	}
+
+	ret = clk_prepare_enable(dsi->video_aclk);
+	if (ret) {
+		dev_err(dev, "failed to enable video clk %d\n", ret);
+		goto err_disable_dphy_clk;
+	}
+
+	ret = component_add(dev, &xlnx_dsi_component_ops);
+	if (ret < 0)
+		goto err_disable_video_clk;
+
+	return ret;
+
+err_disable_video_clk:
+	clk_disable_unprepare(dsi->video_aclk);
+err_disable_dphy_clk:
+	clk_disable_unprepare(dsi->dphy_clk_200M);
+	return ret;
+}
+
+static int xlnx_dsi_remove(struct platform_device *pdev)
+{
+	struct xlnx_dsi *dsi = platform_get_drvdata(pdev);
+
+	component_del(&pdev->dev, &xlnx_dsi_component_ops);
+	clk_disable_unprepare(dsi->video_aclk);
+	clk_disable_unprepare(dsi->dphy_clk_200M);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_dsi_of_match[] = {
+	{ .compatible = "xlnx,dsi"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xlnx_dsi_of_match);
+
+static struct platform_driver dsi_driver = {
+	.probe = xlnx_dsi_probe,
+	.remove = xlnx_dsi_remove,
+	.driver = {
+		.name = "xlnx-dsi",
+		.of_match_table = xlnx_dsi_of_match,
+	},
+};
+
+module_platform_driver(dsi_driver);
+
+MODULE_AUTHOR("Siva Rajesh <sivaraj@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx FPGA MIPI DSI Tx Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_fb.c
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS Framebuffer helper
+ *
+ *  Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * Based on drm_fb_cma_helper.c
+ *
+ *  Copyright (C) 2012 Analog Device Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drm_vblank.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+
+#include "xlnx_crtc.h"
+#include "xlnx_drv.h"
+#include "xlnx_fb.h"
+
+static struct drm_framebuffer_funcs xlnx_fb_funcs = {
+	.destroy	= drm_gem_fb_destroy,
+	.create_handle	= drm_gem_fb_create_handle,
+};
+
+/**
+ * xlnx_fb_create - (struct drm_mode_config_funcs *)->fb_create callback
+ * @drm: DRM device
+ * @file_priv: drm file private data
+ * @mode_cmd: mode command for fb creation
+ *
+ * This functions creates a drm_framebuffer with xlnx_fb_funcs for given mode
+ * @mode_cmd. This functions is intended to be used for the fb_create callback
+ * function of drm_mode_config_funcs.
+ *
+ * Return: a drm_framebuffer object if successful, or
+ * ERR_PTR from drm_gem_fb_create_with_funcs().
+ */
+struct drm_framebuffer *
+xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
+	       const struct drm_mode_fb_cmd2 *mode_cmd)
+{
+	return drm_gem_fb_create_with_funcs(drm, file_priv, mode_cmd,
+					    &xlnx_fb_funcs);
+}
+
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+
+struct xlnx_fbdev {
+	struct drm_fb_helper fb_helper;
+	struct drm_framebuffer *fb;
+	unsigned int align;
+	unsigned int vres_mult;
+};
+
+static inline struct xlnx_fbdev *to_fbdev(struct drm_fb_helper *fb_helper)
+{
+	return container_of(fb_helper, struct xlnx_fbdev, fb_helper);
+}
+
+static int
+xlnx_fb_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
+{
+	struct drm_fb_helper *fb_helper = info->par;
+	struct drm_mode_set *mode_set;
+	int ret = 0;
+
+	switch (cmd) {
+	case FBIO_WAITFORVSYNC:
+		drm_client_for_each_modeset(mode_set, &fb_helper->client) {
+			struct drm_crtc *crtc;
+
+			crtc = mode_set->crtc;
+			ret = drm_crtc_vblank_get(crtc);
+			if (!ret) {
+				drm_crtc_wait_one_vblank(crtc);
+				drm_crtc_vblank_put(crtc);
+			}
+		}
+		return ret;
+	default:
+		return -ENOTTY;
+	}
+
+	return 0;
+}
+
+static struct fb_ops xlnx_fbdev_ops = {
+	.owner		= THIS_MODULE,
+	.fb_fillrect	= sys_fillrect,
+	.fb_copyarea	= sys_copyarea,
+	.fb_imageblit	= sys_imageblit,
+	.fb_check_var	= drm_fb_helper_check_var,
+	.fb_set_par	= drm_fb_helper_set_par,
+	.fb_blank	= drm_fb_helper_blank,
+	.fb_pan_display	= drm_fb_helper_pan_display,
+	.fb_setcmap	= drm_fb_helper_setcmap,
+	.fb_ioctl	= xlnx_fb_ioctl,
+};
+
+static struct drm_framebuffer *
+xlnx_fb_gem_fb_alloc(struct drm_device *drm,
+		     const struct drm_mode_fb_cmd2 *mode_cmd,
+		     struct drm_gem_object **obj, unsigned int num_planes,
+		     const struct drm_framebuffer_funcs *funcs)
+{
+	struct drm_framebuffer *fb;
+	int ret, i;
+
+	fb = kzalloc(sizeof(*fb), GFP_KERNEL);
+	if (!fb)
+		return ERR_PTR(-ENOMEM);
+
+	drm_helper_mode_fill_fb_struct(drm, fb, mode_cmd);
+
+	for (i = 0; i < num_planes; i++)
+		fb->obj[i] = obj[i];
+
+	ret = drm_framebuffer_init(drm, fb, funcs);
+	if (ret) {
+		dev_err(drm->dev, "Failed to init framebuffer: %d\n", ret);
+		kfree(fb);
+		return ERR_PTR(ret);
+	}
+
+	return fb;
+}
+
+static struct drm_framebuffer *
+xlnx_fb_gem_fbdev_fb_create(struct drm_device *drm,
+			struct drm_fb_helper_surface_size *size,
+			unsigned int pitch_align, struct drm_gem_object *obj,
+			const struct drm_framebuffer_funcs *funcs)
+{
+	struct drm_mode_fb_cmd2 mode_cmd = { 0 };
+
+	mode_cmd.width = size->surface_width;
+	mode_cmd.height = size->surface_height;
+	mode_cmd.pitches[0] = size->surface_width *
+			      DIV_ROUND_UP(size->surface_bpp, 8);
+	if (pitch_align)
+		mode_cmd.pitches[0] = roundup(mode_cmd.pitches[0],
+					      pitch_align);
+	mode_cmd.pixel_format = drm_driver_legacy_fb_format(drm,
+							    size->surface_bpp,
+							    size->surface_depth);
+	if (obj->size < (size_t)mode_cmd.pitches[0] * mode_cmd.height)
+		return ERR_PTR(-EINVAL);
+
+	return xlnx_fb_gem_fb_alloc(drm, &mode_cmd, &obj, 1, funcs);
+}
+
+/**
+ * xlnx_fbdev_create - Create the fbdev with a framebuffer
+ * @fb_helper: fb helper structure
+ * @size: framebuffer size info
+ *
+ * This function is based on drm_fbdev_cma_create().
+ *
+ * Return: 0 if successful, or the error code.
+ */
+static int xlnx_fbdev_create(struct drm_fb_helper *fb_helper,
+			     struct drm_fb_helper_surface_size *size)
+{
+	struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
+	struct drm_device *drm = fb_helper->dev;
+	struct drm_gem_cma_object *obj;
+	struct drm_framebuffer *fb;
+	unsigned int bytes_per_pixel;
+	unsigned long offset;
+	struct fb_info *fbi;
+	u32 format;
+	const struct drm_format_info *info;
+	size_t bytes;
+	int ret;
+
+	dev_dbg(drm->dev, "surface width(%d), height(%d) and bpp(%d)\n",
+		size->surface_width, size->surface_height, size->surface_bpp);
+
+	size->surface_height *= fbdev->vres_mult;
+	bytes_per_pixel = DIV_ROUND_UP(size->surface_bpp, 8);
+	bytes = ALIGN((size_t)size->surface_width * bytes_per_pixel,
+		      fbdev->align);
+	bytes *= size->surface_height;
+
+	obj = drm_gem_cma_create(drm, bytes);
+	if (IS_ERR(obj))
+		return PTR_ERR(obj);
+
+	fbi = framebuffer_alloc(0, drm->dev);
+	if (!fbi) {
+		dev_err(drm->dev, "Failed to allocate framebuffer info.\n");
+		ret = -ENOMEM;
+		goto err_drm_gem_cma_free_object;
+	}
+
+	/* Override the depth given by fb helper with current format value */
+	format = xlnx_get_format(drm);
+	info = drm_format_info(format);
+	if (size->surface_bpp == info->cpp[0] * 8)
+		size->surface_depth = info->depth;
+
+	fbdev->fb = xlnx_fb_gem_fbdev_fb_create(drm, size, fbdev->align,
+						&obj->base, &xlnx_fb_funcs);
+	if (IS_ERR(fbdev->fb)) {
+		dev_err(drm->dev, "Failed to allocate DRM framebuffer.\n");
+		ret = PTR_ERR(fbdev->fb);
+		goto err_framebuffer_release;
+	}
+
+	fb = fbdev->fb;
+	fb_helper->fb = fb;
+	fb_helper->fbdev = fbi;
+	fbi->flags = FBINFO_FLAG_DEFAULT;
+	fbi->fbops = &xlnx_fbdev_ops;
+
+	ret = fb_alloc_cmap(&fbi->cmap, 256, 0);
+	if (ret) {
+		dev_err(drm->dev, "Failed to allocate color map.\n");
+		goto err_fb_destroy;
+	}
+
+	drm_fb_helper_fill_info(fbi, fb_helper, size);
+	fbi->var.yres = fb->height / fbdev->vres_mult;
+
+	offset = (unsigned long)fbi->var.xoffset * bytes_per_pixel;
+	offset += fbi->var.yoffset * fb->pitches[0];
+
+	drm->mode_config.fb_base = (resource_size_t)obj->paddr;
+	fbi->screen_base = (char __iomem *)(obj->vaddr + offset);
+	fbi->fix.smem_start = (unsigned long)(obj->paddr + offset);
+	fbi->screen_size = bytes;
+	fbi->fix.smem_len = bytes;
+
+	return 0;
+
+err_fb_destroy:
+	drm_framebuffer_unregister_private(fb);
+	drm_gem_fb_destroy(fb);
+err_framebuffer_release:
+	framebuffer_release(fbi);
+err_drm_gem_cma_free_object:
+	drm_gem_cma_free_object(&obj->base);
+	return ret;
+}
+
+static struct drm_fb_helper_funcs xlnx_fb_helper_funcs = {
+	.fb_probe = xlnx_fbdev_create,
+};
+
+/**
+ * xlnx_fb_init - Allocate and initializes the Xilinx framebuffer
+ * @drm: DRM device
+ * @preferred_bpp: preferred bits per pixel for the device
+ * @max_conn_count: maximum number of connectors
+ * @align: alignment value for pitch
+ * @vres_mult: multiplier for virtual resolution
+ *
+ * This function is based on drm_fbdev_cma_init().
+ *
+ * Return: a newly allocated drm_fb_helper struct or a ERR_PTR.
+ */
+struct drm_fb_helper *
+xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
+	     unsigned int max_conn_count, unsigned int align,
+	     unsigned int vres_mult)
+{
+	struct xlnx_fbdev *fbdev;
+	struct drm_fb_helper *fb_helper;
+	int ret;
+
+	fbdev = kzalloc(sizeof(*fbdev), GFP_KERNEL);
+	if (!fbdev)
+		return ERR_PTR(-ENOMEM);
+
+	fbdev->vres_mult = vres_mult;
+	fbdev->align = align;
+	fb_helper = &fbdev->fb_helper;
+	drm_fb_helper_prepare(drm, fb_helper, &xlnx_fb_helper_funcs);
+
+	ret = drm_fb_helper_init(drm, fb_helper);
+	if (ret < 0) {
+		dev_err(drm->dev, "Failed to initialize drm fb helper.\n");
+		goto err_free;
+	}
+
+	ret = drm_fb_helper_initial_config(fb_helper, preferred_bpp);
+	if (ret < 0) {
+		dev_err(drm->dev, "Failed to set initial hw configuration.\n");
+		goto err_drm_fb_helper_fini;
+	}
+
+	return fb_helper;
+
+err_drm_fb_helper_fini:
+	drm_fb_helper_fini(fb_helper);
+err_free:
+	kfree(fbdev);
+	return ERR_PTR(ret);
+}
+
+/**
+ * xlnx_fbdev_defio_fini - Free the defio fb
+ * @fbi: fb_info struct
+ *
+ * This function is based on drm_fbdev_cma_defio_fini().
+ */
+static void xlnx_fbdev_defio_fini(struct fb_info *fbi)
+{
+	if (!fbi->fbdefio)
+		return;
+
+	fb_deferred_io_cleanup(fbi);
+	kfree(fbi->fbdefio);
+	kfree(fbi->fbops);
+}
+
+/**
+ * xlnx_fbdev_fini - Free the Xilinx framebuffer
+ * @fb_helper: drm_fb_helper struct
+ *
+ * This function is based on drm_fbdev_cma_fini().
+ */
+void xlnx_fb_fini(struct drm_fb_helper *fb_helper)
+{
+	struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
+
+	drm_fb_helper_unregister_fbi(&fbdev->fb_helper);
+	if (fbdev->fb_helper.fbdev)
+		xlnx_fbdev_defio_fini(fbdev->fb_helper.fbdev);
+
+	if (fbdev->fb_helper.fb)
+		drm_framebuffer_remove(fbdev->fb_helper.fb);
+
+	drm_fb_helper_fini(&fbdev->fb_helper);
+	kfree(fbdev);
+}
+
+#endif /* CONFIG_DRM_FBDEV_EMULATION */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_fb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_fb.h
@@ -0,0 +1,52 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx DRM KMS Framebuffer helper header
+ *
+ *  Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_FB_H_
+#define _XLNX_FB_H_
+
+struct drm_fb_helper;
+
+struct drm_framebuffer *
+xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
+	       const struct drm_mode_fb_cmd2 *mode_cmd);
+
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+
+struct drm_fb_helper *
+xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
+	     unsigned int max_conn_count, unsigned int align,
+	     unsigned int vres_mult);
+void xlnx_fb_fini(struct drm_fb_helper *fb_helper);
+
+#else /* CONFIG_DRM_FBDEV_EMULATION */
+
+static inline struct drm_fb_helper *
+xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
+	     unsigned int max_conn_count, unsigned int align,
+	     unsigned int vres_mult)
+{
+	return NULL;
+}
+
+static inline void xlnx_fb_fini(struct drm_fb_helper *fb_helper)
+{
+}
+
+#endif /* CONFIG_DRM_FBDEV_EMULATION */
+
+#endif /* _XLNX_FB_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_gem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_gem.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS GEM helper
+ *
+ *  Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drm_drv.h>
+#include <drm/drm_gem_cma_helper.h>
+
+#include "xlnx_drv.h"
+#include "xlnx_gem.h"
+
+/*
+ * xlnx_gem_cma_dumb_create - (struct drm_driver)->dumb_create callback
+ * @file_priv: drm_file object
+ * @drm: DRM object
+ * @args: info for dumb scanout buffer creation
+ *
+ * This function is for dumb_create callback of drm_driver struct. Simply
+ * it wraps around drm_gem_cma_dumb_create() and sets the pitch value
+ * by retrieving the value from the device.
+ *
+ * Return: The return value from drm_gem_cma_dumb_create()
+ */
+int xlnx_gem_cma_dumb_create(struct drm_file *file_priv, struct drm_device *drm,
+			     struct drm_mode_create_dumb *args)
+{
+	int pitch = DIV_ROUND_UP(args->width * args->bpp, 8);
+	unsigned int align = xlnx_get_align(drm);
+
+	if (!args->pitch || !IS_ALIGNED(args->pitch, align))
+		args->pitch = ALIGN(pitch, align);
+
+	return drm_gem_cma_dumb_create_internal(file_priv, drm, args);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_gem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_gem.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx DRM KMS GEM helper header
+ *
+ *  Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_GEM_H_
+#define _XLNX_GEM_H_
+
+int xlnx_gem_cma_dumb_create(struct drm_file *file_priv,
+			     struct drm_device *drm,
+			     struct drm_mode_create_dumb *args);
+
+#endif /* _XLNX_GEM_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_hdmi.c
@@ -0,0 +1,3053 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA HDMI TX Subsystem Driver
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ *
+ * Author: Venkateshwar Rao G <vgannava.xilinx.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/sysfs.h>
+#include <linux/workqueue.h>
+
+#include <uapi/linux/media-bus-format.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_of.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_sysfs.h>
+
+/* Parallel Interface registers */
+#define HDMI_TX_PIO_ID				0x40
+#define HDMI_TX_PIO_CTRL			0x44
+#define HDMI_TX_PIO_CTRL_IE			BIT(1)
+#define HDMI_TX_PIO_CTRL_RUN			BIT(0)
+#define HDMI_TX_PIO_CTRL_SET			0x48
+#define HDMI_TX_PIO_CTRL_CLR			0x4c
+#define HDMI_TX_PIO_STA				0x50
+#define HDMI_TX_PIO_STA_EVT			BIT(1)
+#define HDMI_TX_PIO_STA_IRQ			BIT(0)
+#define HDMI_TX_PIO_OUT				0x54
+#define HDMI_TX_PIO_OUT_GCP_AVMUTE		BIT(31)
+#define HDMI_TX_PIO_OUT_BRIDGE_PIXEL		BIT(30)
+#define HDMI_TX_PIO_OUT_BRIDGE_YUV420		BIT(29)
+#define HDMI_TX_PIO_OUT_GCP_CLEARAVMUTE		BIT(28)
+#define HDMI_TX_PIO_OUT_EXT_SYSRST		BIT(22)
+#define HDMI_TX_PIO_OUT_EXT_VRST		BIT(21)
+#define HDMI_TX_PIO_OUT_INT_LRST		BIT(20)
+#define HDMI_TX_PIO_OUT_SCRM			BIT(12)
+#define HDMI_TX_PIO_OUT_CS			GENMASK(11, 10)
+#define HDMI_TX_PIO_OUT_SR			GENMASK(9, 8)
+#define HDMI_TX_PIO_OUT_PR			GENMASK(7, 6)
+#define HDMI_TX_PIO_OUT_CD			GENMASK(5, 4)
+#define HDMI_TX_PIO_OUT_CD_SHIFT		4
+#define HDMI_TX_PIO_OUT_PR_SHIFT		6
+#define HDMI_TX_PIO_OUT_SR_SHIFT		8
+#define HDMI_TX_PIO_OUT_CS_SHIFT		10
+#define HDMI_TX_PIO_OUT_MODE			BIT(3)
+#define HDMI_TX_PIO_OUT_INT_VRST		BIT(0)
+#define HDMI_TX_PIO_OUT_SET			0x58
+#define HDMI_TX_PIO_OUT_CLR			0x5c
+#define HDMI_TX_PIO_OUT_MSK			0x60
+#define HDMI_TX_PIO_IN				0x64
+#define HDMI_TX_PIO_IN_BRIDGE_UFLOW		BIT(11)
+#define HDMI_TX_PIO_IN_BRIDGE_OFLOW		BIT(10)
+#define HDMI_TX_PIO_IN_BRIDGE_LOCKED		BIT(9)
+#define HDMI_TX_PIO_IN_HPD_TOGGLE		BIT(8)
+#define HDMI_TX_PIO_IN_PPP			GENMASK(7, 5)
+#define HDMI_TX_PIO_IN_ERR			BIT(4)
+#define HDMI_TX_PIO_IN_VS			BIT(3)
+#define HDMI_TX_PIO_IN_HPD_CONNECT		BIT(2)
+#define HDMI_TX_PIO_IN_VID_RDY			BIT(1)
+#define HDMI_TX_PIO_IN_LNK_RDY			BIT(0)
+#define HDMI_TX_PIO_IN_EVT			0x68
+#define HDMI_TX_PIO_IN_EVT_RE			0x6c
+#define HDMI_TX_PIO_IN_EVT_FE			0x70
+#define HDMI_TX_HPD_TIMEGRID			0x74
+#define HDMI_TX_HPD_TOGGLE_CONF			0x78
+#define HDMI_TX_HPD_CONNECT_CONF		0x7c
+
+/* Display Data Channel registers */
+#define HDMI_TX_DDC_ID				0x80
+#define HDMI_TX_DDC_CTRL			0x84
+#define HDMI_TX_DDC_CTRL_CLK_DIV		GENMASK(31, 16)
+#define HDMI_TX_DDC_CTRL_CLK_DIV_SHIFT		16
+#define HDMI_TX_DDC_CTRL_TO_STOP		BIT(2)
+#define HDMI_TX_DDC_CTRL_IE			BIT(1)
+#define HDMI_TX_DDC_CTRL_RUN			BIT(0)
+#define HDMI_TX_DDC_CTRL_SET			0x88
+#define HDMI_TX_DDC_CTRL_CLR			0x8c
+#define HDMI_TX_DDC_STA				0x90
+#define HDMI_TX_DDC_STA_DAT_USED_WRDS		GENMASK(31, 24)
+#define HDMI_TX_DDC_STA_CMD_FREE_WRDS		GENMASK(23, 16)
+#define HDMI_TX_DDC_STA_DAT_EMPTY		BIT(9)
+#define HDMI_TX_DDC_STA_CMD_FULL		BIT(8)
+#define HDMI_TX_DDC_STA_SDA			BIT(7)
+#define HDMI_TX_DDC_STA_SCL			BIT(6)
+#define HDMI_TX_DDC_STA_ACK			BIT(5)
+#define HDMI_TX_DDC_STA_TO			BIT(4)
+#define HDMI_TX_DDC_STA_DONE			BIT(3)
+#define HDMI_TX_DDC_STA_BUSY			BIT(2)
+#define HDMI_TX_DDC_STA_EVT			BIT(1)
+#define HDMI_TX_DDC_STA_IRQ			BIT(0)
+#define HDMI_TX_DDC_CMD				0x94
+#define HDMI_TX_DDC_DAT				0x98
+
+/* Auxiliary peripheral registers */
+#define HDMI_TX_AUX_ID				0xc0
+#define HDMI_TX_AUX_CTRL			0xc4
+#define HDMI_TX_AUX_CTRL_IE			BIT(1)
+#define HDMI_TX_AUX_CTRL_RUN			BIT(0)
+#define HDMI_TX_AUX_CTRL_SET			0xc8
+#define HDMI_TX_AUX_CTRL_CLR			0xcc
+#define HDMI_TX_AUX_STA				0xd0
+#define HDMI_TX_AUX_STA_FREE_PKTS		GENMASK(7, 4)
+#define HDMI_TX_AUX_STA_PKT_RDY			BIT(3)
+#define HDMI_TX_AUX_STA_FL			BIT(2)
+#define HDMI_TX_AUX_STA_EP			BIT(1)
+#define HDMI_TX_AUX_STA_IRQ			BIT(0)
+#define HDMI_TX_AUX_DAT				0xd4
+
+/* Audio peripheral registers */
+#define HDMI_TX_AUD_ID				0x100
+#define HDMI_TX_AUD_CTRL			0x104
+#define HDMI_TX_AUD_CTRL_AUD_CLK_RATIO		GENMASK(15, 12)
+#define HDMI_TX_AUD_CTRL_TMDS_LNKCLK_RATIO	GENMASK(11, 8)
+#define HDMI_TX_AUD_CTRL_ACR_SEL		BIT(7)
+#define HDMI_TX_AUD_CTRL_ACR_EN			BIT(6)
+#define HDMI_TX_AUD_CTRL_AUD_RESET		BIT(5)
+#define HDMI_TX_AUD_CTRL_AUD_FMT		BIT(4)
+#define HDMI_TX_AUD_CTRL_CH			GENMASK(3, 2)
+#define HDMI_TX_AUD_CTRL_IE			BIT(1)
+#define HDMI_TX_AUD_CTRL_RUN			BIT(0)
+#define HDMI_TX_AUD_CTRL_SET			0x108
+#define HDMI_TX_AUD_CTRL_CLR			0x10c
+#define HDMI_TX_AUD_STA				0x110
+#define HDMI_TX_AUD_ACR_N			0x114
+#define HDMI_TX_AUD_ACR_CTS			0x118
+#define HDMI_TX_AUD_ACR_CTS_ACR_CTS		GENMASK(19, 0)
+#define HDMI_TX_AUD_ACR_CTS_VLD			BIT(31)
+
+/* Video mask peripheral registers */
+#define HDMI_TX_VID_MSK_ID			0x140
+#define HDMI_TX_VID_MSK_CTRL			0x144
+#define HDMI_TX_VID_MSK_CTRL_IE			BIT(1)
+#define HDMI_TX_VID_MSK_CTRL_RUN		BIT(0)
+#define HDMI_TX_VID_MSK_CTRL_SET		0x148
+#define HDMI_TX_VID_MSK_CTRL_CLR		0x14c
+#define HDMI_TX_VID_MSK_STA			0x150
+#define HDMI_TX_VID_MSK_COMP_RED		0x154
+#define HDMI_TX_VID_MSK_COMP_GREEN		0x158
+#define HDMI_TX_VID_MSK_COMP_BLUE		0x15c
+
+/* FRL registers */
+#define HDMI_TX_FRL_ID				0x180
+#define HDMI_TX_FRL_CTRL			0x184
+#define HDMI_TX_FRL_CTRL_FRL_VCKE_EXT		BIT(24)
+#define HDMI_TX_FRL_CTRL_FRL_LTP3_REQ		GENMASK(23, 20)
+#define HDMI_TX_FRL_CTRL_FRL_LTP2_REQ		GENMASK(19, 16)
+#define HDMI_TX_FRL_CTRL_FRL_LTP1_REQ		GENMASK(15, 12)
+#define HDMI_TX_FRL_CTRL_FRL_LTP0_REQ		GENMASK(11, 8)
+#define HDMI_TX_FRL_CTRL_FRL_REQ_MASK		0xF
+#define HDMI_TX_FRL_CTRL_FRL_LTP0_SHIFT		8
+#define HDMI_TX_FRL_CTRL_FRL_LTP1_SHIFT		12
+#define HDMI_TX_FRL_CTRL_FRL_LTP2_SHIFT		16
+#define HDMI_TX_FRL_CTRL_FRL_LTP3_SHIFT		20
+#define HDMI_TX_FRL_CTRL_FRL_ACT		BIT(7)
+#define HDMI_TX_FRL_CTRL_TST_RC_DISABLE		BIT(5)
+#define HDMI_TX_FRL_CTRL_EXEC			BIT(4)
+#define HDMI_TX_FRL_CTRL_FRL_LN_OP		BIT(3)
+#define HDMI_TX_FRL_CTRL_OP_MODE		BIT(2)
+#define HDMI_TX_FRL_CTRL_IE			BIT(1)
+#define HDMI_TX_FRL_CTRL_RST			BIT(0)
+#define HDMI_TX_FRL_CTRL_SET			0x188
+#define HDMI_TX_FRL_CTRL_CLR			0x18c
+#define HDMI_TX_FRL_STA				0x190
+#define HDMI_TX_FRL_STA_GB_SYNC_ERR		BIT(8)
+#define HDMI_TX_FRL_STA_GB_EP			BIT(7)
+#define HDMI_TX_FRL_STA_VID_CLK_OOS		BIT(6)
+#define HDMI_TX_FRL_STA_LNK_CLK_OOS		BIT(5)
+#define HDMI_TX_FRL_STA_TRIB_RST		BIT(4)
+#define HDMI_TX_FRL_STA_FRL_RST			BIT(3)
+#define HDMI_TX_FRL_STA_TMR_ZERO		BIT(2)
+#define HDMI_TX_FRL_STA_TMR_EVT			BIT(1)
+#define HDMI_TX_FRL_STA_IRQ			BIT(0)
+#define HDMI_TX_FRL_TMR				0x194
+#define HDMI_TX_FRL_LNK_CLK			0x198
+#define HDMI_TX_FRL_VID_CLK			0x19c
+#define HDMI_TX_FRL_VP_FIFO_THRD		0x1a0
+#define HDMI_TX_DISP_ERR_INJ			0x1a4
+#define HDMI_TX_DISP_ERR_INJ_NUM_ERR_CB		GENMASK(31, 16)
+#define HDMI_TX_DISP_ERR_INJ_NUM_ERR_CHAR	GENMASK(15, 8)
+#define HDMI_TX_DISP_ERR_INJ_ERR_TYPE		GENMASK(6, 4)
+#define HDMI_TX_DISP_ERR_INJ_DISP_ERR_INJ_EN	BIT(0)
+#define HDMI_TX_FEC_ERR_INJ			0x1a8
+#define HDMI_TX_FEC_ERR_INJ_ERR_CB_LOC		GENMASK(25, 16)
+#define HDMI_TX_FEC_ERR_INJ_NUM_ERR_CB		GENMASK(15, 8)
+#define HDMI_TX_FEC_ERR_INJ_NUM_ERR_CHAR	GENMASK(7, 4)
+#define HDMI_TX_FEC_ERR_INJ_FEC_ERR_INJ_EN	BIT(0)
+/* VTC register offsets and bit masks */
+#define HDMI_TX_VTC_CTL				0x000
+#define HDMI_TX_VTC_CTL_MASK			GENMASK(18, 8)
+#define HDMI_TX_VTC_RST				BIT(31)
+#define HDMI_TX_VTC_CTL_GE			BIT(2)
+#define HDMI_TX_VTC_CTL_RU			BIT(1)
+
+#define HDMI_TX_VTC_GASIZE_F0			0x060
+#define HDMI_TX_VTC_ACTIVE_SIZE_MASK		GENMASK(12, 0)
+
+#define HDMI_TX_VTC_GFENC			0x068
+#define HDMI_TX_VTC_GFENC_MASK			BIT(6)
+
+#define HDMI_TX_VTC_GPOL			0x06c
+#define HDMI_TX_VTC_GPOL_FIELD_ID_POL		BIT(6)
+#define HDMI_TX_VTC_ACTIVE_CHROMA_POL		BIT(5)
+#define HDMI_TX_VTC_ACTIVE_VIDEO_POL		BIT(4)
+#define HDMI_TX_VTC_HSYNC_POL			BIT(3)
+#define HDMI_TX_VTC_VSYNC_POL			BIT(2)
+#define HDMI_TX_VTC_HBLANK_POL			BIT(1)
+#define HDMI_TX_VTC_VBLANK_POL			BIT(0)
+#define HDMI_TX_VTC_GPOL_MASK		(HDMI_TX_VTC_VBLANK_POL |\
+					 HDMI_TX_VTC_HBLANK_POL |\
+					 HDMI_TX_VTC_VSYNC_POL |\
+					 HDMI_TX_VTC_HSYNC_POL |\
+					 HDMI_TX_VTC_ACTIVE_VIDEO_POL |\
+					 HDMI_TX_VTC_ACTIVE_CHROMA_POL)
+
+#define HDMI_TX_VTC_INT_GPOL_MASK	(HDMI_TX_VTC_GPOL_FIELD_ID_POL |\
+					 HDMI_TX_VTC_ACTIVE_CHROMA_POL |\
+					 HDMI_TX_VTC_ACTIVE_VIDEO_POL)
+
+#define HDMI_TX_VTC_GHSIZE			0x070
+#define HDMI_TX_VTC_GHSIZE_FRAME_HSIZE		GENMASK(12, 0)
+
+#define HDMI_TX_VTC_GVSIZE			0x074
+#define HDMI_TX_VTC_FIELD1_VSIZE_SHIFT		16
+#define HDMI_TX_VTC_GVSIZE_FRAME_VSIZE		GENMASK(12, 0)
+
+#define HDMI_TX_VTC_GHSYNC			0x078
+#define HDMI_TX_VTC_GH1BPSTART_SHIFT		16
+#define HDMI_TX_VTC_GHSYNC_END_MASK		GENMASK(28, 16)
+#define HDMI_TX_VTC_GHSYNC_START_MASK		GENMASK(12, 0)
+
+#define HDMI_TX_VTC_GVBHOFF			0x07c
+#define HDMI_TX_VTC_F0VSYNC_HEND_SHIFT		16
+#define HDMI_TX_VTC_F0VBLANK_HEND_MASK		GENMASK(28, 16)
+#define HDMI_TX_VTC_F0VBLANK_HSTART_MASK	GENMASK(12, 0)
+
+#define HDMI_TX_VTC_GVSYNC			0x080
+#define HDMI_TX_VTC_F0_VSYNC_VEND_MASK		GENMASK(28, 16)
+#define HDMI_TX_VTC_F0_VSYNC_VSTART_MASK	GENMASK(12, 0)
+
+#define HDMI_TX_VTC_GVSHOFF			0x084
+#define HDMI_TX_VTC_GVBHOFF_F1			0x088
+#define HDMI_TX_VTC_GVSYNC_F1			0x08c
+#define HDMI_TX_VTC_GVSHOFF_F1			0x090
+#define HDMI_TX_VTC_GASIZE_F1			0x094
+
+#define HDMI_TX_VTC_BASE			0x10000
+#define HDMI_MAX_LANES				4
+
+#define HDMI_TX_3_4_GBPS			340000000
+#define HDMI_TX_SCRAMBLER_OFFSET		0x20
+#define HDMI_TX_TIMEGRID_VAL			0x18696
+#define HDMI_TX_TOGGLE_CONF_VAL			0x630032
+#define HDMI_TX_CONNECT_CONF_VAL		0xA0064
+#define HDMI_TX_DDC_SLAVEADDR			0x54
+#define HDMI_TX_DDC_CLKDIV			100000
+#define HDMI_TX_DDC_EDID_LENGTH			256
+#define HDMI_TX_DDC_EDID_SINK_BW		187
+#define HDMI_TX_DDC_EDID_BW_SHIFT		4
+#define HDMI_TX_DDC_ADDR			0x50
+#define HDMI_TX_DDC_READ_DIR			1
+#define HDMI_TX_DDC_DATA_MSK			0xFF
+#define HDMI_TX_DDC_CMD_MSK			0xFE
+#define HDMI_TX_DDC_CFG_1_FFE_LVLS_MASK		0xF
+#define HDMI_TX_DDC_CFG_1_FFE_LVLS_SHIFT	4
+#define HDMI_TX_DDC_CFG_1_FRL_RATE_MASK		0xF
+#define HDMI_TX_DDC_SINK_VER_REG		0x01
+#define HDMI_TX_DDC_UPDATE_FLGS_REG		0x10
+#define HDMI_TX_DDC_CED_REG			0x50
+#define HDMI_TX_DDC_STCR_REG			0x35
+#define HDMI_TX_DDC_STAT_FLGS_REG		0x40
+#define HDMI_TX_DDC_STAT_FLGS_LN01_REG		0x41
+#define HDMI_TX_DDC_STAT_FLGS_LN23_REG		0x42
+#define HDMI_TX_DDC_UPDATE_FLGS_CED_UPDATE_MASK	0x02
+#define HDMI_TX_DDC_UPDATE_FLGS_STUPDATE_MASK	0x08
+#define HDMI_TX_DDC_UPDATE_FLGS_FRL_START_MASK	0x10
+#define HDMI_TX_DDC_UPDATE_FLGS_FLT_UPDATE_MASK	0x20
+#define HDMI_TX_DDC_STCR_FLT_NO_TIMEOUT_MASK	0x20
+#define HDMI_TX_DDC_STAT_FLGS_FLT_RDY_MASK	0x40
+#define HDMI_TX_DDC_STAT_FLGS_LN01_LN0_MASK	0x0F
+#define HDMI_TX_DDC_STAT_FLGS_LN01_LN1_SHIFT	4
+#define HDMI_TX_DDC_STAT_FLGS_LN23_LN2_MASK	0x0F
+#define HDMI_TX_DDC_STAT_FLGS_LN23_LN3_MASK	0x0F
+#define HDMI_TX_DDC_STAT_FLGS_LN23_LN3_SHIFT	4
+
+#define HDMI_TX_FRL_CLK_CYCLES			0x3E7
+#define HDMI_TX_PIXEL_MAXRATE			2376000
+#define HDMI_TX_PIXELRATE_GBPS			((u64)1e9)
+
+#define HDMI_TX_DDC_CMD_STR_TOKEN		0x100
+#define HDMI_TX_DDC_CMD_STP_TOKEN		0x101
+#define HDMI_TX_DDC_CMD_RD_TOKEN		0x102
+#define HDMI_TX_DDC_CMD_WR_TOKEN		0x103
+
+#define hdmi_mutex_lock(x)	mutex_lock(x)
+#define hdmi_mutex_unlock(x)	mutex_unlock(x)
+
+#define TIMEOUT_2MS		2
+#define TIMEOUT_5MS		5
+#define TIMEOUT_100MS		100
+#define TIMEOUT_200MS		200
+#define TIMEOUT_250MS		250
+#define TIMEOUT_10US		10
+
+#define HDMI_TX_MAX_FRL_RATE	6
+#define HDMI_TX_SCDC_MASK	0xFF
+
+/**
+ * enum hdmi_state - Stream state
+ * @HDMI_TX_STATE_STREAM_DOWN: stream down
+ * @HDMI_TX_STATE_STREAM_UP: stream up
+ */
+enum hdmi_state {
+	HDMI_TX_STATE_STREAM_DOWN = 0,
+	HDMI_TX_STATE_STREAM_UP = 1
+};
+
+enum color_formats {
+	HDMI_TX_CSF_RGB = 0,
+	HDMI_TX_CSF_YCRCB_444 = 1,
+	HDMI_TX_CSF_YCRCB_422 = 2,
+	HDMI_TX_CSF_YCRCB_420 = 3
+};
+
+enum color_depths {
+	HDMI_TX_BPC_8 = 8,
+	HDMI_TX_BPC_10 = 10,
+	HDMI_TX_BPC_12 = 12,
+	HDMI_TX_BPC_16 = 16
+};
+
+enum config_ppc {
+	HDMI_TX_PPC_1 = 1,
+	HDMI_TX_PPC_2 = 2,
+	HDMI_TX_PPC_4 = 4,
+	HDMI_TX_PPC_8 = 8
+};
+
+enum vid_interface {
+	HDMI_TX_AXI_STREAM = 0,
+	HDMI_TX_NATIVE = 1,
+	HDMI_TX_NATIVE_IDE = 2
+};
+
+/* FRL Training States */
+enum frl_train_state {
+	HDMI_TX_FRLSTATE_LTS_L = 0,
+	HDMI_TX_FRLSTATE_LTS_1 = 1,
+	HDMI_TX_FRLSTATE_LTS_2 = 2,
+	HDMI_TX_FRLSTATE_LTS_3_ARM = 3,
+	HDMI_TX_FRLSTATE_LTS_3 = 4,
+	HDMI_TX_FRLSTATE_LTS_4 = 5,
+	HDMI_TX_FRLSTATE_LTS_P_ARM = 6,
+	HDMI_TX_FRLSTATE_LTS_P = 7,
+	HDMI_TX_FRLSTATE_LTS_P_FRL_RDY = 8
+};
+
+/* LTP type */
+enum frl_ltp_type {
+	HDMI_TX_LTP_NO_LTP = 0,
+	HDMI_TX_LTP_ALL_ONES = 1,
+	HDMI_TX_LTP_ALL_ZEROES = 2,
+	HDMI_TX_LTP_NYQUIST_CLOCK = 3,
+	HDMI_TX_LTP_TXDDE_COMPLIANCE = 4,
+	HDMI_TX_LTP_LFSR0 = 5,
+	HDMI_TX_LTP_LFSR1 = 6,
+	HDMI_TX_LTP_LFSR2 = 7,
+	HDMI_TX_LTP_LFSR3 = 8
+};
+
+enum frl_active_mode {
+	HDMI_TX_FRL_ACTIVE_MODE_GAP_ONLY = 0,
+	HDMI_TX_FRL_ACTIVE_MODE_FULL_STREAM = 1
+};
+
+/* HDMI TX SCDC Fields */
+enum xlnx_hdmi_scdc_fields {
+	HDMI_TX_SCDC_FIELD_SOURCE_VER = 0,
+	HDMI_TX_SCDC_FIELD_SNK_CFG0 = 1,
+	HDMI_TX_SCDC_FIELD_SNK_CFG1 = 2,
+	HDMI_TX_SCDC_FIELD_SNK_STU = 3,
+	HDMI_TX_SCDC_FIELD_CED_UPDATE = 4,
+	HDMI_TX_SCDC_FIELD_FRL_START = 5,
+	HDMI_TX_SCDC_FIELD_FLT_UPDATE = 6,
+	HDMI_TX_SCDC_FIELD_FLT_NO_RETRAIN = 7,
+	HDMI_TX_SCDC_FIELD_SIZE = 8
+};
+
+struct xlnx_hdmi_scdc_field {
+	u8 offset;
+	u8 msk;
+	u8 shift;
+};
+
+static const struct
+xlnx_hdmi_scdc_field scdc_field[HDMI_TX_SCDC_FIELD_SIZE] = {
+	{0x02, 0xFF, 0},/* HDMI_TX_SCDCFIELD_SOURCE_VER */
+	{0x30, 0xFF, 0},/* HDMI_TX_SCDCFIELD_SNK_CFG0 */
+	{0x31, 0xFF, 0},/* HDMI_TX_SCDCFIELD_SNK_CFG1 */
+	{0x10, 0x01, 3},/* HDMI_TX_SCDCFIELD_SNK_STU */
+	{0x10, 0xFF, 1},/* HDMI_TX_SCDCFIELD_CED_UPDATE */
+	{0x10, 0xFF, 4},/* HDMI_TX_SCDCFIELD_FRL_START */
+	{0x10, 0xFF, 5},/* HDMI_TX_SCDCFIELD_FLT_UPDATE */
+	{0x30, 0x01, 1}	/* HDMI_TX_SCDCFIELD_FLT_NO_RETRAIN */
+};
+
+/**
+ * struct xlnx_hdmi_frl_config - FRL config structure
+ * @timer_cnt: frl timer
+ * @timer_event: flag for timer event
+ * @flt_no_timeout: flag for no timeout
+ * @frl_train_states: indicates the frl training state
+ */
+struct xlnx_hdmi_frl_config {
+	u16 timer_cnt;
+	u8 timer_event;
+	u8 flt_no_timeout;
+	enum frl_train_state frl_train_states;
+};
+
+/**
+ * struct xlnx_hdmi_config - Configuration of HDMI
+ * @bpc: Bits per component
+ * @ppc: Pixels per component
+ * @vid_interface: AXI_stream or Native interface
+ * @max_frl_rate: maximum frl rate supported by hardware
+ */
+struct xlnx_hdmi_config {
+	enum color_depths bpc;
+	enum config_ppc ppc;
+	enum vid_interface vid_interface;
+	u8 max_frl_rate;
+};
+
+/**
+ * struct xlnx_hdmi_stream - Stream status
+ * @frl_config: frl config structure
+ * @is_frl: flag indicates frl or tmds
+ * @tmds_clock_ratio: tmds clock ratio
+ * @is_hdmi: flag indicates dvi or hdmi
+ * @is_scrambled: scrambled enabled status;
+ * @sink_max_linerate: maximum linerate supported by sink in Gbps
+ * @sink_max_lanes: maximum lanes supported by sink
+ * @state: enum reflects the stream is up or down
+ */
+struct xlnx_hdmi_stream {
+	struct xlnx_hdmi_frl_config frl_config;
+	u8 is_frl;
+	u8 tmds_clock_ratio;
+	u8 is_hdmi;
+	u8 is_scrambled;
+	u8 sink_max_linerate;
+	u8 sink_max_lanes;
+	enum hdmi_state state;
+};
+
+/**
+ * struct xlnx_hdmi - Xilinx HDMI core
+ * @dev: device structure
+ * @encoder: the drm encoder structure
+ * @connector: the drm connector structure
+ * @base: device I/O memory for register access
+ * @irq: hdmi subsystem irq
+ * @phy: PHY handle for hdmi lanes
+ * @hdmi_mutex: mutex to lock hdmi structure
+ * @irq_lock: to lock irq handler
+ * @cable_connected: flag to indicate cable state
+ * @hdmi_stream_up: flag to inidcate video stream state
+ * @is_hdmi_20_sink: flag to indicate if sink is hdmi2.0 capable
+ * @dpms: current dpms state
+ * @xvidc_colorfmt: hdmi ip internal colorformat representation
+ * @xvidc_colordepth: color depth
+ * @config: IP configuration structure
+ * @stream: stream properties
+ * @intr_status: Flag to indicate irq status
+ * @frl_status: Flag to indicate FRL interrupt status
+ * @wait_for_streamup: Flag for stream up
+ * @tmds_clk: TMDS clock
+ * @wait_event: Wait event
+ */
+struct xlnx_hdmi {
+	struct device *dev;
+	struct drm_encoder encoder;
+	struct drm_connector connector;
+	void __iomem *base;
+	int irq;
+	struct phy *phy[HDMI_MAX_LANES];
+	/* to lock hdmi */
+	struct mutex hdmi_mutex;
+	/* to lock irq */
+	spinlock_t irq_lock;
+	bool cable_connected;
+	bool hdmi_stream_up;
+	bool is_hdmi_20_sink;
+	int dpms;
+	enum color_formats xvidc_colorfmt;
+	enum color_depths xvidc_colordepth;
+	struct xlnx_hdmi_config config;
+	struct xlnx_hdmi_stream stream;
+	u32 intr_status;
+	u32 frl_status;
+	u32 wait_for_streamup:1;
+	u32 tmds_clk;
+	wait_queue_head_t wait_event;
+};
+
+enum xlnx_hdmitx_clks {
+	S_AXI_CPU_ACLK = 0,
+	LINK_CLK = 1,
+	VIDEO_CLK = 2,
+	FRL_CLK = 3,
+	S_AXIS_VIDEO_ACLK = 4,
+};
+
+static struct clk_bulk_data hdmitx_clks[] = {
+	{ .id = "s_axi_cpu_aclk" },
+	{ .id = "link_clk" },
+	{ .id = "video_clk" },
+	{ .id = "frl_clk" },
+	{ .id = "s_axis_video_aclk" },
+};
+
+/* Parallel Interface */
+#define xlnx_hdmi_piointr_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_CTRL_CLR,\
+			 HDMI_TX_PIO_CTRL_IE)
+
+#define xlnx_hdmi_piointr_clear(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_STA,\
+			 HDMI_TX_PIO_STA_IRQ)
+
+#define xlnx_hdmi_piointr_ie_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_CTRL_SET,\
+			 HDMI_TX_PIO_CTRL_IE)
+
+#define xlnx_hdmi_piointr_run_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_CTRL_SET,\
+			 HDMI_TX_PIO_CTRL_RUN)
+
+#define xlnx_hdmi_pio_set_sr(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_MSK,\
+			 HDMI_TX_PIO_OUT_SR)
+
+#define xlnx_hdmi_pio_set_pr(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_MSK,\
+			 HDMI_TX_PIO_OUT_PR)
+
+#define xlnx_hdmi_pio_set_cs(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_MSK,\
+			 HDMI_TX_PIO_OUT_CS)
+
+#define xlnx_hdmi_pio_set_cd(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_MSK,\
+			 HDMI_TX_PIO_OUT_CD)
+
+#define xlnx_pioout_bridge_yuv_clr(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR,\
+			 HDMI_TX_PIO_OUT_BRIDGE_YUV420)
+
+#define xlnx_pioout_bridge_pixel_clr(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR,\
+			 HDMI_TX_PIO_OUT_BRIDGE_PIXEL)
+
+#define xlnx_hdmi_auxintr_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_AUX_CTRL_SET,\
+			 HDMI_TX_AUD_CTRL_IE)
+
+/* Data Display Channel */
+#define xlnx_hdmi_ddc_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_CTRL_CLR,\
+			 HDMI_TX_DDC_CTRL_RUN)
+
+#define xlnx_hdmi_ddc_intr_clear(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_STA,\
+			 HDMI_TX_DDC_STA_IRQ)
+
+#define xlnx_hdmi_ddc_set_done(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_STA,\
+			 HDMI_TX_DDC_STA_DONE)
+
+#define xlnx_hdmi_ddc_set_timeout(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_STA,\
+			 HDMI_TX_DDC_STA_TO)
+
+#define xlnx_hdmi_ddc_intr_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_CTRL_CLR,\
+			 HDMI_TX_DDC_CTRL_IE)
+
+#define xlnx_hdmi_ddc_stop_cmd(hdmi) \
+	xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_STP_TOKEN)
+
+#define xlnx_hdmi_ddc_rdtoken_cmd(hdmi) \
+	xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_RD_TOKEN)
+
+#define xlnx_hdmi_ddc_rd_data(hdmi) \
+	xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_DAT)
+
+#define xlnx_hdmi_ddc_run_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_CTRL_SET,\
+			 HDMI_TX_DDC_CTRL_RUN)
+
+/* Audio */
+#define xlnx_hdmi_audio_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_AUD_CTRL_CLR,\
+			 HDMI_TX_AUD_CTRL_RUN)
+/* Aux communication */
+#define xlnx_hdmi_aux_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_AUX_CTRL_CLR,\
+			 HDMI_TX_AUX_CTRL_RUN)
+
+#define xlnx_hdmi_aux_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_AUX_CTRL_SET,\
+			 HDMI_TX_AUX_CTRL_RUN)
+
+#define xlnx_hdmi_auxintr_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_AUX_CTRL_SET,\
+			 HDMI_TX_AUD_CTRL_IE)
+
+#define xlnx_hdmi_auxintr_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_AUX_CTRL_CLR,\
+			 HDMI_TX_AUD_CTRL_IE)
+
+/* Fixed Rate Link */
+#define xlnx_hdmi_frl_intr_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_CLR,\
+			 HDMI_TX_FRL_CTRL_IE)
+
+#define xlnx_hdmi_frl_intr_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,\
+			 HDMI_TX_FRL_CTRL_IE)
+
+#define xlnx_hdmi_frl_clear(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_CLR,\
+			 HDMI_TX_FRL_CTRL_RST)
+
+#define xlnx_hdmi_frl_ext_vidsrc(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,\
+			 HDMI_TX_FRL_CTRL_FRL_VCKE_EXT)
+
+#define xlnx_hdmi_frl_reset(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,\
+			 HDMI_TX_FRL_CTRL_RST)
+
+#define xlnx_hdmi_frl_reset_assert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_CLR,\
+			 HDMI_TX_FRL_CTRL_RST)
+
+#define xlnx_hdmi_frl_reset_deassert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,\
+			 HDMI_TX_FRL_CTRL_RST)
+
+#define xlnx_hdmi_frl_sleep(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL,\
+			 HDMI_TX_FRL_CTRL_RST |\
+			 HDMI_TX_FRL_CTRL_IE |\
+			 HDMI_TX_FRL_CTRL_EXEC)
+
+#define xlnx_hdmi_frl_mode_enable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,\
+			 HDMI_TX_FRL_CTRL_OP_MODE)
+
+#define xlnx_hdmi_frl_mode_disable(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_CLR,\
+			 HDMI_TX_FRL_CTRL_OP_MODE)
+
+#define xlnx_hdmi_frl_execute(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,\
+			 HDMI_TX_FRL_CTRL_EXEC)
+
+#define xlnx_hdmi_set_hdmi_mode(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_SET,\
+			 HDMI_TX_PIO_OUT_MODE)
+
+/* assert VID_IN bridge resets */
+#define xlnx_hdmi_ext_sysrst_assert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR,\
+			 HDMI_TX_PIO_OUT_EXT_SYSRST)
+
+#define xlnx_hdmi_ext_vrst_assert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR,\
+			 HDMI_TX_PIO_OUT_EXT_VRST)
+
+#define xlnx_hdmi_int_lrst_assert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR,\
+			 HDMI_TX_PIO_OUT_INT_LRST)
+
+#define xlnx_hdmi_int_vrst_assert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR,\
+			 HDMI_TX_PIO_OUT_INT_VRST)
+
+#define xlnx_hdmi_ext_sysrst_deassert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_SET,\
+			 HDMI_TX_PIO_OUT_EXT_SYSRST)
+
+#define xlnx_hdmi_ext_vrst_deassert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_SET,\
+			 HDMI_TX_PIO_OUT_EXT_VRST)
+
+#define xlnx_hdmi_int_lrst_deassert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_SET,\
+			 HDMI_TX_PIO_OUT_INT_LRST)
+
+#define xlnx_hdmi_int_vrst_deassert(hdmi) \
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_SET,\
+			 HDMI_TX_PIO_OUT_INT_VRST)
+
+/* video timing controller */
+#define xlnx_hdmi_vtc_enable(hdmi) \
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_CTL, HDMI_TX_VTC_CTL_GE)
+
+#define xlnx_hdmi_vtc_disable(hdmi) \
+	xlnx_hdmi_vtc_clr(hdmi, HDMI_TX_VTC_CTL, HDMI_TX_VTC_CTL_GE)
+
+static inline void
+xlnx_hdmi_writel(struct xlnx_hdmi *hdmi, u32 offset, u32 val)
+{
+	writel(val, hdmi->base + offset);
+}
+
+static inline u32 xlnx_hdmi_readl(struct xlnx_hdmi *hdmi, int offset)
+{
+	return readl(hdmi->base + offset);
+}
+
+static void xlnx_hdmi_clr(struct xlnx_hdmi *hdmi, int offset, u32 clr)
+{
+	xlnx_hdmi_writel(hdmi, offset, xlnx_hdmi_readl(hdmi, offset) & ~clr);
+}
+
+static inline void
+xlnx_hdmi_vtc_writel(struct xlnx_hdmi *hdmi, u32 offset, u32 val)
+{
+	writel(val, hdmi->base + HDMI_TX_VTC_BASE + offset);
+}
+
+static inline u32
+xlnx_hdmi_vtc_readl(struct xlnx_hdmi *hdmi, u32 offset)
+{
+	return readl(hdmi->base + HDMI_TX_VTC_BASE + offset);
+}
+
+static inline void
+xlnx_hdmi_vtc_clr(struct xlnx_hdmi *hdmi, u32 offset, u32 clr)
+{
+	xlnx_hdmi_vtc_writel(hdmi, offset,
+			     xlnx_hdmi_vtc_readl(hdmi, offset) & ~clr);
+}
+
+static inline void
+xlnx_set_frl_link_clk(struct xlnx_hdmi *hdmi, u32 val)
+{
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_LNK_CLK, val);
+}
+
+static inline void
+xlnx_set_frl_vid_clk(struct xlnx_hdmi *hdmi, u32 val)
+{
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_VID_CLK, val);
+}
+
+static inline struct
+xlnx_hdmi *encoder_to_hdmi(struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct xlnx_hdmi, encoder);
+}
+
+static inline
+struct xlnx_hdmi *connector_to_hdmi(struct drm_connector *connector)
+{
+	return container_of(connector, struct xlnx_hdmi, connector);
+}
+
+/**
+ * xlnx_hdmi_vtc_set_timing - configure video timing parameters
+ * @hdmi: hdmi tx instance
+ * @mode: drm display mode
+ *
+ * Program timing parameters into video timing controller
+ * registers.
+ *
+ * @return: None
+ */
+static void xlnx_hdmi_vtc_set_timing(struct xlnx_hdmi *hdmi,
+				     struct drm_display_mode *mode)
+{
+	u32 reg;
+	u32 htotal, hactive, hsync_start, hbackporch_start;
+	u32 vtotal, vactive, vsync_start, vbackporch_start;
+	u32 hsync_len, hfront_porch, hback_porch;
+	u32 vsync_len, vfront_porch, vback_porch;
+
+	/* vtc reset */
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_CTL, HDMI_TX_VTC_RST);
+	reg = xlnx_hdmi_vtc_readl(hdmi, HDMI_TX_VTC_CTL);
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_CTL, reg | HDMI_TX_VTC_CTL_RU);
+
+	hactive = mode->hdisplay / hdmi->config.ppc;
+	hfront_porch = (mode->hsync_start - mode->hdisplay) / hdmi->config.ppc;
+	hback_porch = (mode->htotal - mode->hsync_end) / hdmi->config.ppc;
+	hsync_len = (mode->hsync_end - mode->hsync_start) / hdmi->config.ppc;
+	htotal = hactive + hfront_porch + hsync_len + hback_porch;
+	hsync_start = hactive + hfront_porch;
+	hbackporch_start = hsync_start + hsync_len;
+
+	vactive = mode->vdisplay;
+	vfront_porch = mode->vsync_start - mode->vdisplay;
+	vback_porch = mode->vtotal - mode->vsync_end;
+	vsync_len = mode->vsync_end - mode->vsync_start;
+	vtotal = vactive + vfront_porch + vsync_len + vback_porch;
+	vsync_start = vactive + vfront_porch;
+	vbackporch_start = vsync_start + vsync_len;
+
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_CTL, reg & ~HDMI_TX_VTC_CTL_RU);
+
+	reg = htotal & HDMI_TX_VTC_GHSIZE_FRAME_HSIZE;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GHSIZE, reg);
+
+	reg = vtotal & HDMI_TX_VTC_GVSIZE_FRAME_VSIZE;
+	reg |= reg << HDMI_TX_VTC_FIELD1_VSIZE_SHIFT;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GVSIZE, reg);
+
+	reg = hactive & HDMI_TX_VTC_ACTIVE_SIZE_MASK;
+	reg |= (vactive & HDMI_TX_VTC_ACTIVE_SIZE_MASK) <<
+		HDMI_TX_VTC_FIELD1_VSIZE_SHIFT;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GASIZE_F0, reg);
+
+	reg = hsync_start & HDMI_TX_VTC_GHSYNC_START_MASK;
+	reg |= (hbackporch_start << HDMI_TX_VTC_GH1BPSTART_SHIFT) &
+		HDMI_TX_VTC_GHSYNC_END_MASK;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GHSYNC, reg);
+
+	reg = vsync_start & HDMI_TX_VTC_F0_VSYNC_VSTART_MASK;
+	reg |= (vbackporch_start << HDMI_TX_VTC_FIELD1_VSIZE_SHIFT) &
+		HDMI_TX_VTC_F0_VSYNC_VEND_MASK;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GVSYNC, reg);
+	xlnx_hdmi_clr(hdmi, HDMI_TX_VTC_BASE + HDMI_TX_VTC_GFENC,
+		      HDMI_TX_VTC_GFENC_MASK);
+
+	/* Calculate and uppdate Generator VBlank Hori field 0 */
+	reg = hactive & HDMI_TX_VTC_F0VBLANK_HSTART_MASK;
+	reg |= (hactive << HDMI_TX_VTC_F0VSYNC_HEND_SHIFT) &
+		HDMI_TX_VTC_F0VBLANK_HEND_MASK;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GVBHOFF, reg);
+
+	/* Calculate and update Generator VSync Hori field 0 */
+	reg = hsync_start & HDMI_TX_VTC_F0VBLANK_HSTART_MASK;
+	reg |= (hsync_start << HDMI_TX_VTC_F0VSYNC_HEND_SHIFT) &
+		HDMI_TX_VTC_F0VBLANK_HEND_MASK;
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GVSHOFF, reg);
+
+	/* sets all polarities as active high */
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_GPOL, HDMI_TX_VTC_GPOL_MASK);
+	/* configure timing source */
+	xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_CTL, HDMI_TX_VTC_CTL_MASK |
+			     HDMI_TX_VTC_CTL_RU);
+}
+
+/**
+ * xlnx_hdmi_ddc_getack: get acknowledge
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: ddc transaction acknowledgment
+ */
+static bool xlnx_hdmi_ddc_getack(struct xlnx_hdmi *hdmi)
+{
+	u32 status;
+
+	status = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_STA);
+
+	return (status & HDMI_TX_DDC_STA_ACK);
+}
+
+/**
+ * xlnx_hdmi_ddcwaitfordone - wait for the ddc done flag to be set
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, 1 on timeout error
+ */
+static bool xlnx_hdmi_ddcwaitfordone(struct xlnx_hdmi *hdmi)
+{
+	u32 data;
+	bool status, val = false;
+
+	do {
+		data = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_CTRL);
+		if (data & HDMI_TX_DDC_CTRL_RUN) {
+			data = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_STA);
+			if (data & HDMI_TX_DDC_STA_DONE) {
+				xlnx_hdmi_ddc_set_done(hdmi);
+				val = true;
+				status = false;
+			} else if (data & HDMI_TX_DDC_STA_TO) {
+				xlnx_hdmi_ddc_set_timeout(hdmi);
+				val = true;
+				status = true;
+			}
+		} else {
+			status = true;
+			val = true;
+		}
+	} while (!val);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_ddcwrite_cmd - writes data into FIFO
+ * @hdmi: pointer to HDMI TX core instance
+ * @cmd: command to be written
+ *
+ * Returns: 0 on success, 1 if fifo full error
+ */
+static u32 xlnx_hdmi_ddcwrite_cmd(struct xlnx_hdmi *hdmi, u32 cmd)
+{
+	int tries = 0;
+	u32 status;
+	bool val = false;
+
+	do {
+		status = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_CTRL);
+		if (status & HDMI_TX_DDC_CTRL_RUN) {
+			status = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_STA);
+			status &= HDMI_TX_DDC_STA_CMD_FULL;
+			if (!status) {
+				xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_CMD, cmd);
+				status = 0;
+				val = true;
+			} else {
+				usleep_range(100, 200);
+				if (tries++ > 10) {
+					xlnx_hdmi_ddc_disable(hdmi);
+					status = 1;
+					val = true;
+				}
+			}
+		} else {
+			status = 1;
+			val = true;
+		}
+	} while (!val);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_ddcwrite - ddc write
+ * @hdmi: pointer to HDMI TX core instance
+ * @slave: slave address
+ * @length: length of the data to be written
+ * @buffer: data buffer
+ * @stop: stop flag
+ *
+ * Returns: 0 if write is successful, 1 on failure.
+ */
+static u32 xlnx_hdmi_ddcwrite(struct xlnx_hdmi *hdmi, u8 slave,
+			      u16 length, u8 *buffer, u8 stop)
+{
+	u32 data, index, status;
+
+	/* ddc enable */
+	xlnx_hdmi_ddc_run_enable(hdmi);
+	xlnx_hdmi_ddc_intr_disable(hdmi);
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_STR_TOKEN);
+	if (status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_WR_TOKEN);
+	if (status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, 0);
+	if (status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, 1);
+	if (status)
+		return status;
+
+	data = slave << 1;
+	data &= HDMI_TX_DDC_CMD_MSK;
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, data);
+	if (status)
+		return status;
+
+	/* Wait for done flag */
+	if (xlnx_hdmi_ddcwaitfordone(hdmi))
+		return 1;
+
+	if (xlnx_hdmi_ddc_getack(hdmi)) {
+		status = xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_WR_TOKEN);
+		if (status)
+			return status;
+
+		data = (length >> 8) & HDMI_TX_DDC_DATA_MSK;
+		status = xlnx_hdmi_ddcwrite_cmd(hdmi, data);
+		if (status)
+			return status;
+
+		data = length & HDMI_TX_DDC_DATA_MSK;
+		status = xlnx_hdmi_ddcwrite_cmd(hdmi, data);
+		if (status)
+			return status;
+
+		for (index = 0; index < length; index++) {
+			status = xlnx_hdmi_ddcwrite_cmd(hdmi, *buffer++);
+			if (status)
+				return status;
+		}
+		if (!xlnx_hdmi_ddcwaitfordone(hdmi)) {
+			if (xlnx_hdmi_ddc_getack(hdmi)) {
+				if (stop) {
+					status = xlnx_hdmi_ddc_stop_cmd(hdmi);
+					if (status)
+						return status;
+
+					xlnx_hdmi_ddcwaitfordone(hdmi);
+				}
+				status = 0;
+			}
+		}
+	}
+	xlnx_hdmi_ddc_disable(hdmi);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_ddcreaddata - read data
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: Byte data from ddc
+ */
+static u8 xlnx_hdmi_ddcreaddata(struct xlnx_hdmi *hdmi)
+{
+	u32 status;
+	int tries = 0;
+	u8 data;
+	bool val = false;
+
+	do {
+		data = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_CTRL);
+		if (data & HDMI_TX_DDC_CTRL_RUN) {
+			status = xlnx_hdmi_readl(hdmi, HDMI_TX_DDC_STA);
+			status &= HDMI_TX_DDC_STA_DAT_EMPTY;
+			if (!status) {
+				data = xlnx_hdmi_ddc_rd_data(hdmi);
+				val = true;
+			} else {
+				usleep_range(1000, 1100);
+				if (tries++ > 10) {
+					xlnx_hdmi_ddc_disable(hdmi);
+					val = true;
+					data = 0;
+				}
+			}
+		} else {
+			val = true;
+			data = 0;
+		}
+	} while (!val);
+
+	return data;
+}
+
+/**
+ * xlnx_hdmi_ddcread - read bulk data from ddc
+ * @hdmi: pointer to HDMI TX core instance
+ * @slave: slave address
+ * @length: length of data to be read
+ * @buffer: destination buffer address
+ * @stop: stop flag
+ *
+ * Returns: 0 on success, 1 on timeout errors
+ */
+static u32 xlnx_hdmi_ddcread(struct xlnx_hdmi *hdmi, u8 slave,
+			     u16 length, u8 *buffer, u8 stop)
+{
+	u32 data, index, status;
+
+	/* ddc enable */
+	xlnx_hdmi_ddc_run_enable(hdmi);
+	xlnx_hdmi_ddc_intr_disable(hdmi);
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_STR_TOKEN);
+	if (status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, HDMI_TX_DDC_CMD_WR_TOKEN);
+	if (status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, 0);
+	if (status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, 1);
+	if (status)
+		return status;
+
+	data = slave << 1;
+	/* set read bit */
+	data |= HDMI_TX_DDC_READ_DIR;
+
+	status = xlnx_hdmi_ddcwrite_cmd(hdmi, data);
+	if (status)
+		return status;
+
+	/* Wait for done flag */
+	if (!xlnx_hdmi_ddcwaitfordone(hdmi)) {
+		if (xlnx_hdmi_ddc_getack(hdmi)) {
+			status = xlnx_hdmi_ddc_rdtoken_cmd(hdmi);
+			if (status)
+				return status;
+
+			data = (length >> 8) & HDMI_TX_DDC_DATA_MSK;
+			status = xlnx_hdmi_ddcwrite_cmd(hdmi, data);
+			if (status)
+				return status;
+
+			data = length & HDMI_TX_DDC_DATA_MSK;
+			status = xlnx_hdmi_ddcwrite_cmd(hdmi, data);
+			if (status)
+				return status;
+
+			/* read data */
+			for (index = 0; index < length; index++)
+				*buffer++ = xlnx_hdmi_ddcreaddata(hdmi);
+			if (!xlnx_hdmi_ddcwaitfordone(hdmi)) {
+				if (stop) {
+					status = xlnx_hdmi_ddc_stop_cmd(hdmi);
+					if (status)
+						return(status);
+
+					xlnx_hdmi_ddcwaitfordone(hdmi);
+				}
+				status = 0;
+			}
+		}
+	}
+	xlnx_hdmi_ddc_disable(hdmi);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_ddc_readreg - read register from ddc
+ * @hdmi: pointer to HDMI TX core instance
+ * @slave: slave address
+ * @length: length of the data to be read
+ * @reg_addr: register address
+ * @buffer: destination buffer address
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int
+xlnx_hdmi_ddc_readreg(struct xlnx_hdmi *hdmi, u8 slave, u16 length,
+		      u8 reg_addr, u8 *buffer)
+{
+	int status;
+
+	/* Set the register to be read */
+	status = xlnx_hdmi_ddcwrite(hdmi, slave, 1, (u8 *)&reg_addr, false);
+	if (!status)
+		status = xlnx_hdmi_ddcread(hdmi, slave, length,
+					   (u8 *)buffer, true);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_ddcwrite_field - writes specified SCDC field
+ * @hdmi: HDMI TX core instance structure
+ * @field: field from SCDC channel to be written
+ * @val: value to be written
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_ddcwrite_field(struct xlnx_hdmi *hdmi,
+				    enum xlnx_hdmi_scdc_fields field, u8 val)
+{
+	u32 status;
+	u8 ddc_buf[2] = {0};
+	u8 offset = scdc_field[field].offset;
+
+	if (scdc_field[field].msk != HDMI_TX_SCDC_MASK) {
+		status = xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+					    (u8 *)&offset, false);
+		if (status)
+			return status;
+
+		status = xlnx_hdmi_ddcread(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+					   (u8 *)&ddc_buf, true);
+		if (status)
+			return status;
+
+		ddc_buf[0] &= ~(scdc_field[field].msk <<
+				scdc_field[field].shift);
+	} else {
+		ddc_buf[0] |= ((val & scdc_field[field].msk) <<
+			       scdc_field[field].shift);
+	}
+
+	ddc_buf[1] = ddc_buf[0];
+	ddc_buf[0] = offset;
+	return xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_SLAVEADDR, 2,
+				  (u8 *)&ddc_buf, true);
+}
+
+/**
+ * xlnx_hdmi_set_samplerate - set sample rate
+ * @hdmi: pointer to HDMI TX core instance
+ * @samplerate: sample rate value
+ *
+ * Returns: None
+ */
+static void
+xlnx_hdmi_set_samplerate(struct xlnx_hdmi *hdmi, unsigned int samplerate)
+{
+	u32 regvalue;
+
+	xlnx_hdmi_pio_set_sr(hdmi);
+
+	switch (samplerate) {
+	case 2:
+		regvalue = 2;
+		break;
+	case 3:
+		regvalue = 1;
+		break;
+	case 5:
+		regvalue = 3;
+		break;
+	default:
+		regvalue = 0;
+		break;
+	}
+
+	/* set sample rate */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT,
+			 (regvalue << (HDMI_TX_PIO_OUT_SR_SHIFT)));
+}
+
+/**
+ * xlnx_hdmi_set_ppc - set pixel per clock
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: None
+ */
+static void xlnx_hdmi_set_ppc(struct xlnx_hdmi *hdmi)
+{
+	u32 regvalue;
+
+	/* Mask PIO Out Mask register */
+	xlnx_hdmi_pio_set_pr(hdmi);
+
+	/* Check for pixel width */
+	switch (hdmi->config.ppc) {
+	case HDMI_TX_PPC_2:
+		regvalue = 1;
+		break;
+	case HDMI_TX_PPC_4:
+		regvalue = 2;
+		break;
+	case HDMI_TX_PPC_8:
+		regvalue = 3;
+		break;
+	default:
+		regvalue = 0;
+		break;
+	}
+	/* Write pixel rate into PIO Out register */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT,
+			 (regvalue << HDMI_TX_PIO_OUT_PR_SHIFT));
+}
+
+/**
+ * xlnx_hdmi_set_colorfmt - set color format
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: None
+ */
+static void xlnx_hdmi_set_colorfmt(struct xlnx_hdmi *hdmi)
+{
+	u32 regvalue;
+
+	/* Mask PIO Out Mask register */
+	xlnx_hdmi_pio_set_cs(hdmi);
+
+	/* Check for color format */
+	switch (hdmi->xvidc_colorfmt) {
+	case HDMI_TX_CSF_YCRCB_444:
+		regvalue = 1;
+		break;
+	case HDMI_TX_CSF_YCRCB_422:
+		regvalue = 2;
+		break;
+	case HDMI_TX_CSF_YCRCB_420:
+		regvalue = 3;
+		break;
+	default:
+		regvalue = 0;
+		break;
+	}
+	/* Write color space into PIO Out register */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT,
+			 (regvalue << HDMI_TX_PIO_OUT_CS_SHIFT));
+}
+
+/**
+ * xlnx_hdmi_set_colordepth - set color depth
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: None
+ */
+static void xlnx_hdmi_set_colordepth(struct xlnx_hdmi *hdmi)
+{
+	u32 regvalue;
+
+	/* Mask PIO Out Mask register */
+	xlnx_hdmi_pio_set_cd(hdmi);
+
+	switch (hdmi->config.bpc) {
+	case HDMI_TX_BPC_10:
+		regvalue = 1;
+		break;
+	case HDMI_TX_BPC_12:
+		regvalue = 2;
+		break;
+	case HDMI_TX_BPC_16:
+		regvalue = 3;
+		break;
+	default:
+		regvalue = 0;
+		break;
+	}
+	/* Write color depth into PIO Out register */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT,
+			 regvalue << HDMI_TX_PIO_OUT_CD_SHIFT);
+}
+
+/**
+ * xlnx_hdmi_clkratio - set clock ratio
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, error if ddc write fails.
+ */
+static u32
+xlnx_hdmi_clkratio(struct xlnx_hdmi *hdmi)
+{
+	u32 status;
+	u8 ddc_buf[2];
+
+	ddc_buf[0] = HDMI_TX_SCRAMBLER_OFFSET;
+	status = xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				    (u8 *)&ddc_buf, false);
+	if (status)
+		return status;
+
+	/* Read TMDS configuration */
+	status = xlnx_hdmi_ddcread(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				   (u8 *)&ddc_buf, true);
+	ddc_buf[0] &= 0xfd;
+
+	if (hdmi->stream.tmds_clock_ratio)
+		ddc_buf[0] |= 0x02;
+	ddc_buf[1] = ddc_buf[0];
+	ddc_buf[0] = HDMI_TX_SCRAMBLER_OFFSET;
+
+	status = xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_SLAVEADDR, 2,
+				    (u8 *)&ddc_buf, true);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_stream_start - set core parameters
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, 1 if ddc transaction fails
+ */
+static u32 xlnx_hdmi_stream_start(struct xlnx_hdmi *hdmi)
+{
+	u8 ddc_buf[2];
+	int status;
+
+	xlnx_hdmi_set_ppc(hdmi);
+	xlnx_hdmi_set_colorfmt(hdmi);
+	xlnx_hdmi_set_colordepth(hdmi);
+
+	/*
+	 * Set the TMDS clock ratio bit if the data rate is higher
+	 * than 3.4Gb/s
+	 */
+	if (hdmi->tmds_clk > HDMI_TX_3_4_GBPS) {
+		hdmi->stream.is_scrambled = true;
+		hdmi->stream.tmds_clock_ratio = true;
+	} else {
+		hdmi->stream.is_scrambled = false;
+		hdmi->stream.tmds_clock_ratio = false;
+	}
+
+	/* set scrambler */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_OUT_CLR, HDMI_TX_PIO_OUT_SCRM);
+
+	ddc_buf[0] = HDMI_TX_SCRAMBLER_OFFSET;
+	status = xlnx_hdmi_ddcread(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				   (u8 *)&ddc_buf, false);
+	if (!status)
+		return status;
+
+	status = xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				    (u8 *)&ddc_buf, true);
+	if (status) {
+		ddc_buf[1] = ddc_buf[0] & HDMI_TX_DDC_CMD_MSK;
+		ddc_buf[1] |= hdmi->stream.is_scrambled;
+
+		status = xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_SLAVEADDR, 2,
+					    (u8 *)&ddc_buf, true);
+	}
+	/* set clock ratio */
+	xlnx_hdmi_clkratio(hdmi);
+	return status;
+}
+
+/**
+ * xlnx_hdmi_set_frl_active: sets active FRL mode.
+ *
+ * @hdmi: HDMI TX core instance
+ * @mode: Mode specifies the active FRL mode.
+ * 0 = FRL transmission only includes GAP characters
+ * 1 = FRL transmission includes video, audio and control packets
+ */
+static void
+xlnx_hdmi_set_frl_active(struct xlnx_hdmi *hdmi, enum frl_active_mode mode)
+{
+	if (mode)
+		xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,
+				 HDMI_TX_FRL_CTRL_FRL_ACT);
+	else
+		xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_CLR,
+				 HDMI_TX_FRL_CTRL_FRL_ACT);
+}
+
+/**
+ * xlnx_hdmi_set_frl_ltp: sets the link training pattern for the selected lane.
+ *
+ * @hdmi: pointer to HDMI TX instance
+ * @lane: lane number
+ * @ltp_type: link training pattern type
+ */
+static void
+xlnx_hdmi_set_frl_ltp(struct xlnx_hdmi *hdmi, u8 lane, u8 ltp_type)
+{
+	u32 value = ltp_type;
+	u32 data;
+
+	data = xlnx_hdmi_readl(hdmi, HDMI_TX_FRL_CTRL);
+
+	switch (lane) {
+	case 0:
+		data = data & ~((u32)(HDMI_TX_FRL_CTRL_FRL_REQ_MASK <<
+				      HDMI_TX_FRL_CTRL_FRL_LTP0_SHIFT));
+		data = data | ((value & HDMI_TX_FRL_CTRL_FRL_REQ_MASK) <<
+			       HDMI_TX_FRL_CTRL_FRL_LTP0_SHIFT);
+		break;
+	case 1:
+		data = data & ~((u32)(HDMI_TX_FRL_CTRL_FRL_REQ_MASK <<
+				      HDMI_TX_FRL_CTRL_FRL_LTP1_SHIFT));
+		data = data | ((value & HDMI_TX_FRL_CTRL_FRL_REQ_MASK) <<
+			       HDMI_TX_FRL_CTRL_FRL_LTP1_SHIFT);
+		break;
+	case 2:
+		data = data & ~((u32)(HDMI_TX_FRL_CTRL_FRL_REQ_MASK <<
+				      HDMI_TX_FRL_CTRL_FRL_LTP2_SHIFT));
+		data = data | ((value & HDMI_TX_FRL_CTRL_FRL_REQ_MASK) <<
+			       HDMI_TX_FRL_CTRL_FRL_LTP2_SHIFT);
+		break;
+	case 3:
+		data = data & ~((u32)(HDMI_TX_FRL_CTRL_FRL_REQ_MASK <<
+				      HDMI_TX_FRL_CTRL_FRL_LTP3_SHIFT));
+		data = data | ((value & HDMI_TX_FRL_CTRL_FRL_REQ_MASK) <<
+			       HDMI_TX_FRL_CTRL_FRL_LTP3_SHIFT);
+		break;
+	default:
+		dev_dbg(hdmi->dev, "Wrong lane is selected!\n");
+		break;
+	}
+
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL, data);
+}
+
+/**
+ * xlnx_hdmi_set_frl_timer: sets the frl timer value
+ * @hdmi: pinter to HDMI TX core instance
+ * @timer_val: timer value in milliseconds
+ */
+static void xlnx_hdmi_set_frl_timer(struct xlnx_hdmi *hdmi, u32 timer_val)
+{
+	u32 clk_cycles = 0;
+	unsigned long clkrate;
+
+	clkrate = clk_get_rate(hdmitx_clks[S_AXI_CPU_ACLK].clk);
+	if (timer_val == TIMEOUT_10US)
+		clk_cycles = clkrate / 100000;
+	else if (timer_val > 0)
+		clk_cycles = clkrate * timer_val / 1000;
+
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_TMR, clk_cycles);
+}
+
+/**
+ * xlnx_hdmi_clear_frl_ltp - stops sending link training patterns
+ * @hdmi: pointer to HDMI TX core instance
+ */
+static void xlnx_hdmi_clear_frl_ltp(struct xlnx_hdmi *hdmi)
+{
+	u32 index;
+
+	for (index = 0; index < HDMI_MAX_LANES; index++)
+		xlnx_hdmi_set_frl_ltp(hdmi, index, HDMI_TX_LTP_NO_LTP);
+}
+
+/**
+ * xlnx_hdmi_frl_train_init: Initializes sink's SCDC for training.
+ * @hdmi: Pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_frl_train_init(struct xlnx_hdmi *hdmi)
+{
+	int status;
+
+	xlnx_hdmi_clear_frl_ltp(hdmi);
+	xlnx_hdmi_set_frl_active(hdmi, HDMI_TX_FRL_ACTIVE_MODE_GAP_ONLY);
+	xlnx_hdmi_frl_mode_enable(hdmi);
+
+	xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_CTRL_SET,
+			 HDMI_TX_FRL_CTRL_FRL_LN_OP);
+
+	status = xlnx_hdmi_ddcwrite_field(hdmi, HDMI_TX_SCDC_FIELD_SNK_CFG1,
+					  hdmi->config.max_frl_rate);
+	if (status)
+		return status;
+
+	return xlnx_hdmi_ddcwrite_field(hdmi, HDMI_TX_SCDC_FIELD_SNK_CFG0, 0);
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_ltsl - executes legacy training state
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_exec_frl_state_ltsl(struct xlnx_hdmi *hdmi)
+{
+	int status;
+	u8 ddc_buf;
+
+	xlnx_hdmi_set_frl_timer(hdmi, 0);
+	xlnx_hdmi_frl_reset_assert(hdmi);
+	xlnx_hdmi_frl_reset_deassert(hdmi);
+	xlnx_hdmi_frl_mode_disable(hdmi);
+	hdmi->stream.is_frl = 0;
+
+	status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				       HDMI_TX_DDC_UPDATE_FLGS_REG,
+				       (u8 *)&ddc_buf);
+	if (status)
+		return status;
+
+	if (ddc_buf & HDMI_TX_DDC_UPDATE_FLGS_FLT_UPDATE_MASK)
+		status = xlnx_hdmi_ddcwrite_field(hdmi,
+						  HDMI_TX_SCDC_FIELD_FLT_UPDATE,
+						  1);
+	if (!status)
+		xlnx_hdmi_frl_execute(hdmi);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_lts1 - executes FRL LTS1 training state
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_exec_frl_state_lts1(struct xlnx_hdmi *hdmi)
+{
+	int status;
+	u8 ddc_buf;
+
+	/* Read sink version */
+	status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				       HDMI_TX_DDC_SINK_VER_REG,
+				       (u8 *)&ddc_buf);
+
+	if (!status && ddc_buf != 0) {
+		status = xlnx_hdmi_ddcwrite_field(hdmi,
+						  HDMI_TX_SCDC_FIELD_SOURCE_VER,
+						  1);
+
+		if (!status) {
+			hdmi->stream.frl_config.frl_train_states =
+					HDMI_TX_FRLSTATE_LTS_2;
+			hdmi->stream.frl_config.timer_cnt = 0;
+		}
+	} else {
+		hdmi->stream.frl_config.frl_train_states =
+			HDMI_TX_FRLSTATE_LTS_L;
+		status = 1;
+	}
+
+	xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_lts2: executes FRL LTS2 training state
+ * @hdmi: pointer to Hdmi Tx core instance
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction or
+ * phy configure call fails.
+ */
+static int xlnx_hdmi_exec_frl_state_lts2(struct xlnx_hdmi *hdmi)
+{
+	union phy_configure_opts phy_cfg = {0};
+	int status, ret, i;
+	u8 ddc_buf, index;
+
+	hdmi->stream.frl_config.timer_cnt += TIMEOUT_5MS;
+	status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				       HDMI_TX_DDC_STCR_REG, (u8 *)&ddc_buf);
+	if (status)
+		return status;
+
+	if (ddc_buf & HDMI_TX_DDC_STCR_FLT_NO_TIMEOUT_MASK)
+		hdmi->stream.frl_config.flt_no_timeout = true;
+	else
+		hdmi->stream.frl_config.flt_no_timeout = false;
+
+	status = xlnx_hdmi_ddcwrite_field(hdmi, HDMI_TX_SCDC_FIELD_SNK_STU, 1);
+
+	/* Read FLT_NO_UPDATE SCDC Register */
+	if (!status && (hdmi->stream.frl_config.flt_no_timeout ||
+			hdmi->stream.frl_config.timer_cnt < TIMEOUT_100MS)) {
+		status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+					       HDMI_TX_DDC_STAT_FLGS_REG,
+					       (u8 *)&ddc_buf);
+		if (status)
+			return status;
+
+		if (ddc_buf & HDMI_TX_DDC_STAT_FLGS_FLT_RDY_MASK) {
+			/* Set the training state as LTS_3_ARM */
+			xlnx_hdmi_set_frl_timer(hdmi, 0);
+			hdmi->stream.frl_config.timer_cnt = 0;
+			hdmi->stream.frl_config.frl_train_states =
+					HDMI_TX_FRLSTATE_LTS_3_ARM;
+
+			/* Enable phy ibufds */
+			phy_cfg.hdmi.ibufds = 1;
+			phy_cfg.hdmi.ibufds_en = true;
+			for (i = 0; i < HDMI_MAX_LANES; i++) {
+				ret = phy_configure(hdmi->phy[i], &phy_cfg);
+				if (ret) {
+					dev_err(hdmi->dev, "phy_cfg: Ibufds config failed\n");
+					return ret;
+				}
+			}
+
+			/* Enable HDMI 2.1 config */
+			phy_cfg.hdmi.linerate =
+				(u64)(hdmi->stream.sink_max_linerate *
+				      HDMI_TX_PIXELRATE_GBPS);
+			phy_cfg.hdmi.nchannels = hdmi->stream.sink_max_lanes;
+			phy_cfg.hdmi.config_hdmi21 = 1;
+			for (i = 0; i < HDMI_MAX_LANES; i++) {
+				ret = phy_configure(hdmi->phy[i], &phy_cfg);
+				if (ret) {
+					dev_err(hdmi->dev, "phy_cfg: hdmi21 config failed\n");
+					return ret;
+				}
+			}
+
+			/* set Nyquist Clock as link training pattern */
+			for (index = 0; index < HDMI_MAX_LANES; index++) {
+				xlnx_hdmi_set_frl_ltp(hdmi, index,
+						      HDMI_TX_LTP_NYQUIST_CLOCK);
+			}
+
+			xlnx_hdmi_frl_execute(hdmi);
+		}
+	} else {
+		/* Timeout, fallback to LTS:L training state */
+		hdmi->stream.frl_config.frl_train_states =
+			HDMI_TX_FRLSTATE_LTS_L;
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+	}
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_lts2_ratewr: executes FRL LTS2-wr training state
+ * @hdmi: pointer to Hdmi Tx core instance
+ *
+ * Returns: 0 on success, non zero value on failure
+ */
+static int xlnx_hdmi_exec_frl_state_lts2_ratewr(struct xlnx_hdmi *hdmi)
+{
+	int status;
+
+	status = xlnx_hdmi_frl_train_init(hdmi);
+	if (status) {
+		dev_err(hdmi->dev, "lts2 train init failed\n");
+		return status;
+	}
+
+	xlnx_hdmi_frl_execute(hdmi);
+	hdmi->stream.frl_config.frl_train_states = HDMI_TX_FRLSTATE_LTS_3;
+	xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_lts3: executes FRL LTS3 training state
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_exec_frl_state_lts3(struct xlnx_hdmi *hdmi)
+{
+	int status;
+	u8 ddc_buf[4], ln;
+
+	/* If timeout is 200ms, fallback to LTS:L */
+	if (hdmi->stream.frl_config.timer_cnt > TIMEOUT_200MS &&
+	    !hdmi->stream.frl_config.flt_no_timeout) {
+		hdmi->stream.frl_config.timer_cnt = 0;
+		hdmi->stream.frl_config.frl_train_states =
+			HDMI_TX_FRLSTATE_LTS_L;
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+		return 1;
+	}
+
+	xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_2MS);
+	hdmi->stream.frl_config.timer_cnt += TIMEOUT_2MS;
+
+	status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				       HDMI_TX_DDC_UPDATE_FLGS_REG,
+				       (u8 *)&ddc_buf);
+
+	if (status || (ddc_buf[0] & HDMI_TX_DDC_UPDATE_FLGS_FLT_UPDATE_MASK) !=
+	    HDMI_TX_DDC_UPDATE_FLGS_FLT_UPDATE_MASK)
+		return 1;
+
+	if (ddc_buf[0] & HDMI_TX_DDC_UPDATE_FLGS_STUPDATE_MASK) {
+		status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+					       HDMI_TX_DDC_STCR_REG,
+					       (u8 *)&ddc_buf);
+		if (status)
+			return status;
+
+		if (ddc_buf[0] & HDMI_TX_DDC_STCR_FLT_NO_TIMEOUT_MASK)
+			hdmi->stream.frl_config.flt_no_timeout = true;
+		else
+			hdmi->stream.frl_config.flt_no_timeout = false;
+
+		status = xlnx_hdmi_ddcwrite_field(hdmi,
+						  HDMI_TX_SCDC_FIELD_SNK_STU,
+						  1);
+	}
+
+	status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 2,
+				       HDMI_TX_DDC_STAT_FLGS_LN01_REG,
+				       (u8 *)&ddc_buf);
+	if (status)
+		return status;
+
+	ddc_buf[3] = ddc_buf[1] >> HDMI_TX_DDC_STAT_FLGS_LN23_LN3_SHIFT;
+	ddc_buf[2] = ddc_buf[1] & HDMI_TX_DDC_STAT_FLGS_LN23_LN2_MASK;
+	ddc_buf[1] = ddc_buf[0] >> HDMI_TX_DDC_STAT_FLGS_LN01_LN1_SHIFT;
+	ddc_buf[0] = ddc_buf[0] & HDMI_TX_DDC_STAT_FLGS_LN01_LN0_MASK;
+
+	/* link training is successful, if ddc status flag value is 0x0 */
+	if (ddc_buf[0] == 0x0 && ddc_buf[1] == 0x0 &&
+	    ddc_buf[2] == 0x0 && ddc_buf[3] == 0x0) {
+		hdmi->stream.frl_config.timer_cnt = 0;
+		hdmi->stream.frl_config.frl_train_states =
+			HDMI_TX_FRLSTATE_LTS_P_ARM;
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+		return status;
+	} else if (ddc_buf[0] == 0xF && ddc_buf[1] == 0xF &&
+		   ddc_buf[2] == 0xF && ddc_buf[3] == 0xF) {
+		/* 0xF means a request to drop FRL rate */
+		hdmi->stream.frl_config.timer_cnt = 0;
+		hdmi->stream.frl_config.frl_train_states =
+			HDMI_TX_FRLSTATE_LTS_4;
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+	} else {
+		for (ln = 0; ln < 4; ln++) {
+			/*
+			 * 0x1 to 0x8 means specific link training pattern is
+			 * requested. Each of the lane need to be set to output
+			 * the link training pattern as requested.
+			 */
+			if (ddc_buf[ln] >= 1 && ddc_buf[ln] <= 8) {
+				if (ddc_buf[ln] != 3 ||
+				    hdmi->stream.frl_config.flt_no_timeout)
+					xlnx_hdmi_set_frl_ltp(hdmi, ln,
+							      ddc_buf[ln]);
+			}
+		}
+		xlnx_hdmi_frl_execute(hdmi);
+	}
+
+	return xlnx_hdmi_ddcwrite_field(hdmi, HDMI_TX_SCDC_FIELD_FLT_UPDATE, 1);
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_lts4: executes FRL LTS4 training state
+ * @hdmi: Pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_exec_frl_state_lts4(struct xlnx_hdmi *hdmi)
+{
+	int status = 0;
+
+	xlnx_hdmi_set_frl_timer(hdmi, 0);
+	xlnx_hdmi_clear_frl_ltp(hdmi);
+	status = xlnx_hdmi_ddcwrite_field(hdmi,
+					  HDMI_TX_SCDC_FIELD_FLT_UPDATE, 1);
+	if (!status) {
+		status = xlnx_hdmi_ddcwrite_field(hdmi,
+						  HDMI_TX_SCDC_FIELD_FLT_UPDATE,
+						  1);
+		if (!status) {
+			hdmi->stream.frl_config.timer_cnt = 0;
+			hdmi->stream.frl_config.frl_train_states =
+				HDMI_TX_FRLSTATE_LTS_3_ARM;
+			xlnx_hdmi_frl_execute(hdmi);
+			return status;
+		}
+	}
+
+	hdmi->stream.frl_config.timer_cnt = 0;
+	hdmi->stream.frl_config.frl_train_states = HDMI_TX_FRLSTATE_LTS_L;
+	xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+	xlnx_hdmi_frl_execute(hdmi);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_ltsp_arm: executes FRL LTSP-arm training state
+ * @hdmi: pointer to HDMI TX core instance.
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_exec_frl_state_ltsp_arm(struct xlnx_hdmi *hdmi)
+{
+	int status;
+
+	xlnx_hdmi_clear_frl_ltp(hdmi);
+	/* Send GAP characters */
+	xlnx_hdmi_set_frl_active(hdmi, HDMI_TX_FRL_ACTIVE_MODE_GAP_ONLY);
+	status = xlnx_hdmi_ddcwrite_field(hdmi,
+					  HDMI_TX_SCDC_FIELD_FLT_UPDATE, 1);
+	hdmi->stream.frl_config.frl_train_states = HDMI_TX_FRLSTATE_LTS_P;
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state_ltsp: executes FRL LTS-P training state
+ * @hdmi: pointer to HDMI TX core instance.
+ *
+ * Returns: 0 on success, non-zero value if ddc transaction fails.
+ */
+static int xlnx_hdmi_exec_frl_state_ltsp(struct xlnx_hdmi *hdmi)
+{
+	int status;
+	u8 ddc_buf;
+
+	if (hdmi->stream.frl_config.frl_train_states !=
+	    HDMI_TX_FRLSTATE_LTS_P_FRL_RDY)
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_2MS);
+	else
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_250MS);
+
+	status = xlnx_hdmi_ddc_readreg(hdmi, HDMI_TX_DDC_SLAVEADDR, 1,
+				       HDMI_TX_DDC_UPDATE_FLGS_REG,
+				       (u8 *)&ddc_buf);
+	if (status)
+		return status;
+
+	if (hdmi->stream.frl_config.frl_train_states ==
+	    HDMI_TX_FRLSTATE_LTS_P) {
+		if (ddc_buf & HDMI_TX_DDC_UPDATE_FLGS_FRL_START_MASK) {
+			xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_250MS);
+			status = xlnx_hdmi_ddcwrite_field(hdmi,
+							  HDMI_TX_SCDC_FIELD_FRL_START,
+							  1);
+			if (!status)
+				hdmi->stream.frl_config.frl_train_states =
+					HDMI_TX_FRLSTATE_LTS_P_FRL_RDY;
+		}
+	}
+
+	if (ddc_buf & HDMI_TX_DDC_UPDATE_FLGS_FLT_UPDATE_MASK) {
+		/* Stops transmitting link training pattern */
+		xlnx_hdmi_clear_frl_ltp(hdmi);
+		/* Stops transmitting video, audio and control packets */
+		xlnx_hdmi_set_frl_active(hdmi,
+					 HDMI_TX_FRL_ACTIVE_MODE_GAP_ONLY);
+		hdmi->stream.frl_config.timer_cnt = 0;
+		hdmi->stream.frl_config.frl_train_states =
+			HDMI_TX_FRLSTATE_LTS_3;
+		xlnx_hdmi_set_frl_timer(hdmi, TIMEOUT_10US);
+	} else if (ddc_buf & HDMI_TX_DDC_UPDATE_FLGS_CED_UPDATE_MASK) {
+		xlnx_hdmi_set_frl_timer(hdmi, 0);
+	}
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_exec_frl_state: executes states of FRL.
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: 0 on success, non-zero value on failure
+ */
+static int xlnx_hdmi_exec_frl_state(struct xlnx_hdmi *hdmi)
+{
+	int status = 1;
+
+	xlnx_hdmi_set_frl_timer(hdmi, 0);
+	xlnx_hdmi_frl_intr_enable(hdmi);
+	xlnx_hdmi_frl_execute(hdmi);
+
+	switch (hdmi->stream.frl_config.frl_train_states) {
+	case HDMI_TX_FRLSTATE_LTS_L:
+		status = xlnx_hdmi_exec_frl_state_ltsl(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_1:
+		status = xlnx_hdmi_exec_frl_state_lts1(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_2:
+		status = xlnx_hdmi_exec_frl_state_lts2(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_3_ARM:
+		status = xlnx_hdmi_exec_frl_state_lts2_ratewr(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_3:
+		status = xlnx_hdmi_exec_frl_state_lts3(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_4:
+		status = xlnx_hdmi_exec_frl_state_lts4(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_P_ARM:
+		status = xlnx_hdmi_exec_frl_state_ltsp_arm(hdmi);
+		if (!status)
+			status = xlnx_hdmi_exec_frl_state_ltsp(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_P:
+		status = xlnx_hdmi_exec_frl_state_ltsp(hdmi);
+		break;
+	case HDMI_TX_FRLSTATE_LTS_P_FRL_RDY:
+		status = xlnx_hdmi_exec_frl_state_ltsp(hdmi);
+		break;
+	default:
+		dev_dbg(hdmi->dev, "TX:S:FRL_INVALID_STATE!\n");
+		break;
+	}
+	/* Clear timer event flag */
+	hdmi->stream.frl_config.timer_event = false;
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_start_frl_train - starts the Fixed Rate Link Training.
+ * @hdmi: pointer to the HDMI Tx core instance.
+ * @frl_rate: frl rate to be trained
+ *
+ * Returns: 0 on success, 1 on failure.
+ */
+static int
+xlnx_hdmi_start_frl_train(struct xlnx_hdmi *hdmi, u32 frl_rate)
+{
+	int status;
+
+	hdmi->stream.frl_config.frl_train_states = HDMI_TX_FRLSTATE_LTS_1;
+	hdmi->stream.frl_config.timer_event = false;
+
+	status = xlnx_hdmi_exec_frl_state(hdmi);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_piointr_handler - HDMI TX peripheral interrupt handler.
+ * @hdmi: pointer to HDMI TX core instance
+ *
+ * Returns: None.
+ *
+ * This handler reads corresponding event interrupt from the PIO_IN_EVT
+ * register. It determines the source of the interrupt
+ */
+static void xlnx_hdmi_piointr_handler(struct xlnx_hdmi *hdmi)
+{
+	union phy_configure_opts phy_cfg = {0};
+	int ret, i;
+	u32 event, data;
+
+	/* Read PIO IN Event register */
+	event = xlnx_hdmi_readl(hdmi, HDMI_TX_PIO_IN_EVT);
+
+	/* Clear event flags */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_IN_EVT, event);
+
+	/* Read data */
+	data = xlnx_hdmi_readl(hdmi, HDMI_TX_PIO_IN);
+
+	/* HPD event has occurred */
+	if (event & HDMI_TX_PIO_IN_HPD_TOGGLE)
+		xlnx_hdmi_stream_start(hdmi);
+
+	/* HPD event has occurred */
+	if (event & HDMI_TX_PIO_IN_HPD_CONNECT) {
+		/* Check the HPD status */
+		if (data & HDMI_TX_PIO_IN_HPD_CONNECT) {
+			hdmi->cable_connected = 1;
+			hdmi->connector.status = connector_status_connected;
+			xlnx_hdmi_ddc_disable(hdmi);
+
+			phy_cfg.hdmi.ibufds = 1;
+			phy_cfg.hdmi.ibufds_en = true;
+			for (i = 0; i < HDMI_MAX_LANES; i++) {
+				ret = phy_configure(hdmi->phy[i], &phy_cfg);
+				if (ret) {
+					dev_err(hdmi->dev, "phy_cfg: Ibufds err\n");
+					return;
+				}
+			}
+
+			phy_cfg.hdmi.config_hdmi20 = 1;
+			for (i = 0; i < HDMI_MAX_LANES; i++) {
+				ret = phy_configure(hdmi->phy[i], &phy_cfg);
+				if (ret) {
+					dev_err(hdmi->dev, "phy_cfg: hdmi20 err\n");
+					return;
+				}
+			}
+
+			phy_cfg.hdmi.clkout1_obuftds = 1;
+			phy_cfg.hdmi.clkout1_obuftds_en = false;
+			for (i = 0; i < HDMI_MAX_LANES; i++) {
+				ret = phy_configure(hdmi->phy[i], &phy_cfg);
+				if (ret) {
+					dev_err(hdmi->dev, "phy_cfg:obuftds_en err\n");
+					return;
+				}
+			}
+		} else {
+			hdmi->cable_connected = 0;
+			hdmi->connector.status = connector_status_disconnected;
+			dev_info(hdmi->dev, "stream is not connected\n");
+			phy_cfg.hdmi.clkout1_obuftds = 1;
+			phy_cfg.hdmi.clkout1_obuftds_en = false;
+			for (i = 0; i < HDMI_MAX_LANES; i++) {
+				ret = phy_configure(hdmi->phy[i], &phy_cfg);
+				if (ret) {
+					dev_err(hdmi->dev, "phy_cfg:obuftds_dis err\n");
+					return;
+				}
+			}
+		}
+
+		if (hdmi->connector.dev)
+			drm_sysfs_hotplug_event(hdmi->connector.dev);
+		else
+			dev_dbg(hdmi->dev, "Not sending HOTPLUG.\n");
+	}
+
+	/* Bridge Unlocked event has occurred */
+	if (event & HDMI_TX_PIO_IN_BRIDGE_LOCKED) {
+		dev_dbg(hdmi->dev, "PIO IN status = 0x%x\n",
+			xlnx_hdmi_readl(hdmi, HDMI_TX_PIO_IN));
+		if (data & HDMI_TX_PIO_IN_BRIDGE_LOCKED)
+			dev_dbg(hdmi->dev, "Bridge locked\n");
+		else
+			dev_dbg(hdmi->dev, "Bridge unlocked\n");
+	}
+
+	/* Bridge Overflow event has occurred */
+	if (event & HDMI_TX_PIO_IN_BRIDGE_OFLOW)
+		dev_err_ratelimited(hdmi->dev, "Overflow interrupt\n");
+
+	/* Bridge Underflow event has occurred */
+	if (event & HDMI_TX_PIO_IN_BRIDGE_UFLOW)
+		dev_err_ratelimited(hdmi->dev, "Underflow interrupt\n");
+
+	/* Link ready event has occurred */
+	if (event & HDMI_TX_PIO_IN_LNK_RDY) {
+		/* Check the link status */
+		if (data & HDMI_TX_PIO_IN_LNK_RDY) {
+			hdmi->stream.state = HDMI_TX_STATE_STREAM_UP;
+			if (hdmi->stream.frl_config.frl_train_states ==
+			    HDMI_TX_FRLSTATE_LTS_3_ARM) {
+				/* Execute state machine */
+				xlnx_hdmi_exec_frl_state(hdmi);
+			}
+			if (!hdmi->stream.is_frl) {
+				xlnx_hdmi_aux_enable(hdmi);
+				xlnx_hdmi_auxintr_enable(hdmi);
+
+				phy_cfg.hdmi.clkout1_obuftds = 1;
+				phy_cfg.hdmi.clkout1_obuftds_en = true;
+				for (i = 0; i < HDMI_MAX_LANES; i++) {
+					ret = phy_configure(hdmi->phy[i],
+							    &phy_cfg);
+					if (ret) {
+						dev_err(hdmi->dev, "phy_cfg: 10bufds_en err\n");
+						return;
+					}
+				}
+				xlnx_hdmi_set_samplerate(hdmi, 1);
+
+				/* release vid_in bridge resets */
+				xlnx_hdmi_ext_sysrst_deassert(hdmi);
+				xlnx_hdmi_ext_vrst_deassert(hdmi);
+				/* release tx core resets */
+				xlnx_hdmi_int_lrst_deassert(hdmi);
+				xlnx_hdmi_int_vrst_deassert(hdmi);
+
+				hdmi->hdmi_stream_up = 1;
+
+				xlnx_pioout_bridge_yuv_clr(hdmi);
+				xlnx_pioout_bridge_pixel_clr(hdmi);
+				xlnx_hdmi_stream_start(hdmi);
+				xlnx_hdmi_clkratio(hdmi);
+			}
+		} else {
+			/* Set stream status to down */
+			hdmi->stream.state = HDMI_TX_STATE_STREAM_DOWN;
+			/* Disable AUX */
+			xlnx_hdmi_aux_disable(hdmi);
+		}
+	}
+}
+
+/**
+ * xlnx_hdmi_frlintr_handler - HDMI TX FRL interrupt handler.
+ * @hdmi: pointer to HDMI TX core instance
+ */
+static void xlnx_hdmi_frlintr_handler(struct xlnx_hdmi *hdmi)
+{
+	u32 data;
+
+	/* Read FRL Status register */
+	data = xlnx_hdmi_readl(hdmi, HDMI_TX_FRL_STA);
+
+	/* Check FRL timer event */
+	if ((data) & (HDMI_TX_FRL_STA_TMR_EVT)) {
+		xlnx_hdmi_writel(hdmi, HDMI_TX_FRL_STA,
+				 HDMI_TX_FRL_STA_TMR_EVT);
+		/* Set Timer event flag */
+		hdmi->stream.frl_config.timer_event = true;
+
+		/* Execute state machine */
+		xlnx_hdmi_exec_frl_state(hdmi);
+	}
+}
+
+static irqreturn_t hdmitx_irq_handler(int irq, void *dev_id)
+{
+	struct xlnx_hdmi *hdmi = (struct xlnx_hdmi *)dev_id;
+	unsigned long flags;
+
+	/* read status registers */
+	hdmi->intr_status = xlnx_hdmi_readl(hdmi, HDMI_TX_PIO_STA);
+	hdmi->intr_status &= HDMI_TX_PIO_STA_IRQ;
+
+	if (hdmi->stream.is_frl) {
+		hdmi->frl_status = xlnx_hdmi_readl(hdmi, HDMI_TX_FRL_STA);
+		hdmi->frl_status &= HDMI_TX_FRL_STA_IRQ;
+	}
+
+	spin_lock_irqsave(&hdmi->irq_lock, flags);
+	xlnx_hdmi_piointr_disable(hdmi);
+	if (hdmi->frl_status) {
+		xlnx_hdmi_frl_intr_disable(hdmi);
+		xlnx_hdmi_frl_execute(hdmi);
+	}
+	spin_unlock_irqrestore(&hdmi->irq_lock, flags);
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t hdmitx_irq_thread(int irq, void *data)
+{
+	struct xlnx_hdmi *hdmi = (struct xlnx_hdmi *)data;
+	unsigned long flags;
+
+	if (!hdmi)
+		return IRQ_HANDLED;
+
+	hdmi_mutex_lock(&hdmi->hdmi_mutex);
+
+	if (hdmi->intr_status)
+		xlnx_hdmi_piointr_handler(hdmi);
+
+	if (hdmi->frl_status && hdmi->stream.is_frl)
+		xlnx_hdmi_frlintr_handler(hdmi);
+
+	hdmi->cable_connected = 1;
+
+	hdmi_mutex_unlock(&hdmi->hdmi_mutex);
+
+	spin_lock_irqsave(&hdmi->irq_lock, flags);
+	xlnx_hdmi_piointr_ie_enable(hdmi);
+	spin_unlock_irqrestore(&hdmi->irq_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+/* DRM connector functions */
+static enum drm_connector_status
+xlnx_hdmi_connector_detect(struct drm_connector *connector, bool force)
+{
+	/* it takes HDMI 50 ms to detect connection on init */
+	static int first_time_ms = 50;
+	struct xlnx_hdmi *hdmi = connector_to_hdmi(connector);
+
+	/* first time; wait 50 ms max until cable connected */
+	while (first_time_ms && !hdmi->cable_connected) {
+		msleep(20);
+		first_time_ms--;
+	}
+
+	/* connected in less than 50 ms? */
+	if (first_time_ms) {
+		/* after first time, report immediately */
+		dev_info(hdmi->dev, "detect() waited %d ms until connect.\n",
+			 50 - first_time_ms);
+		first_time_ms = 0;
+	}
+
+	hdmi_mutex_lock(&hdmi->hdmi_mutex);
+	if (hdmi->cable_connected) {
+		hdmi_mutex_unlock(&hdmi->hdmi_mutex);
+		dev_dbg(hdmi->dev, "hdmi_connector_detect() = connected\n");
+		return connector_status_connected;
+	}
+
+	hdmi_mutex_unlock(&hdmi->hdmi_mutex);
+	dev_dbg(hdmi->dev, "hdmi_connector_detect() = disconnected\n");
+
+	return connector_status_disconnected;
+}
+
+static void xlnx_hdmi_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+	connector->dev = NULL;
+}
+
+static const struct drm_connector_funcs xlnx_hdmi_connector_funcs = {
+	.dpms			= drm_helper_connector_dpms,
+	.detect			= xlnx_hdmi_connector_detect,
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= xlnx_hdmi_connector_destroy,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+	.reset			= drm_atomic_helper_connector_reset,
+};
+
+/* DRM connector helper functions */
+static int
+xlnx_hdmi_connector_mode_valid(struct drm_connector *connector,
+			       struct drm_display_mode *mode)
+{
+	struct xlnx_hdmi *hdmi = connector_to_hdmi(connector);
+	enum drm_mode_status status = MODE_OK;
+
+	if (mode->flags & DRM_MODE_FLAG_INTERLACE) {
+		mode->vdisplay = mode->vdisplay / 2;
+		dev_dbg(hdmi->dev, "INTERLACE, mode->vdisplay %d\n",
+			mode->vdisplay);
+	}
+
+	if ((mode->flags & DRM_MODE_FLAG_DBLCLK) &&
+	    (mode->flags & DRM_MODE_FLAG_INTERLACE)) {
+		mode->clock *= 2;
+		dev_dbg(hdmi->dev, "clock = %d, refresh rate = %d\n",
+			mode->clock, drm_mode_vrefresh(mode));
+	}
+
+	drm_mode_debug_printmodeline(mode);
+	hdmi_mutex_lock(&hdmi->hdmi_mutex);
+
+	/* pixel clock too high for sink? */
+	if (mode->clock > HDMI_TX_PIXEL_MAXRATE)
+		status = MODE_CLOCK_HIGH;
+	hdmi_mutex_unlock(&hdmi->hdmi_mutex);
+
+	return status;
+}
+
+/**
+ * xlnx_hdmi_get_edid_block - callback function for drm_do_get_edid() used in
+ * get_modes through drm_do_get_edid() from drm/drm_edid.c.
+ *
+ * @data: pointer to hdmi instance
+ * @buf: buffer pointer to copy edid data
+ * @block: edid block
+ * @len: length of the data to be read
+ *
+ * @return: 0 on success, error code otherwise
+ */
+static int
+xlnx_hdmi_get_edid_block(void *data, u8 *buf, unsigned int block,
+			 size_t len)
+{
+	u8 *buffer;
+	struct xlnx_hdmi *hdmi = data;
+	int ret = 0;
+
+	/* out of bounds? */
+	if (((block * 128) + len) > HDMI_TX_DDC_EDID_LENGTH)
+		return -EINVAL;
+
+	buffer = kzalloc(HDMI_TX_DDC_EDID_LENGTH, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
+
+	/* first obtain edid in local buffer */
+	*buffer = 0;
+	ret = xlnx_hdmi_ddcwrite(hdmi, HDMI_TX_DDC_ADDR, 1, buffer, false);
+
+	if (!ret) {
+		ret = xlnx_hdmi_ddcread(hdmi, HDMI_TX_DDC_ADDR,
+					HDMI_TX_DDC_EDID_LENGTH, buffer, true);
+	} else {
+		kfree(buffer);
+		dev_err(hdmi->dev, "failed reading EDID\n");
+		return -EINVAL;
+	}
+
+	memcpy(buf, buffer + block * 128, len);
+	if (buffer[HDMI_TX_DDC_EDID_SINK_BW] >> HDMI_TX_DDC_EDID_BW_SHIFT)
+		hdmi->stream.is_frl = 1;
+
+	kfree(buffer);
+	return 0;
+}
+
+static int xlnx_hdmi_connector_get_modes(struct drm_connector *connector)
+{
+	struct xlnx_hdmi *hdmi = connector_to_hdmi(connector);
+	struct edid *edid;
+	int ret;
+	bool is_hdmi_sink;
+
+	hdmi_mutex_lock(&hdmi->hdmi_mutex);
+
+	edid = drm_do_get_edid(connector, xlnx_hdmi_get_edid_block, hdmi);
+
+	hdmi_mutex_unlock(&hdmi->hdmi_mutex);
+	if (!edid) {
+		dev_info(hdmi->dev, "no edid, assume <= 1024x768 works\n");
+		drm_connector_update_edid_property(connector, NULL);
+		return 0;
+	}
+
+	/* If the sink is non HDMI, set the stream type to DVI else HDMI */
+	is_hdmi_sink = drm_detect_hdmi_monitor(edid);
+	if (is_hdmi_sink) {
+		dev_dbg(hdmi->dev, "setting stream type to HDMI\n");
+		xlnx_hdmi_set_hdmi_mode(hdmi);
+		hdmi->stream.is_hdmi = true;
+		if (hdmi->stream.is_hdmi)
+			xlnx_hdmi_aux_enable(hdmi);
+	} else {
+		dev_dbg(hdmi->dev, "setting stream type to DVI\n");
+	}
+
+	drm_connector_update_edid_property(connector, edid);
+	ret = drm_add_edid_modes(connector, edid);
+	kfree(edid);
+
+	return ret;
+}
+
+static struct drm_encoder *
+xlnx_hdmi_connector_best_encoder(struct drm_connector *connector)
+{
+	struct xlnx_hdmi *hdmi = connector_to_hdmi(connector);
+
+	return &hdmi->encoder;
+}
+
+static struct
+drm_connector_helper_funcs xlnx_hdmi_connector_helper_funcs = {
+	.get_modes = xlnx_hdmi_connector_get_modes,
+	.best_encoder = xlnx_hdmi_connector_best_encoder,
+	.mode_valid = xlnx_hdmi_connector_mode_valid,
+};
+
+/* DRM encoder functions */
+static void xlnx_hdmi_encoder_dpms(struct drm_encoder *encoder, int dpms)
+{
+	struct xlnx_hdmi *hdmi = encoder_to_hdmi(encoder);
+
+	hdmi_mutex_lock(&hdmi->hdmi_mutex);
+	hdmi->dpms = dpms;
+	hdmi_mutex_unlock(&hdmi->hdmi_mutex);
+}
+
+static void xlnx_hdmi_encoder_enable(struct drm_encoder *encoder)
+{
+	struct xlnx_hdmi *hdmi = encoder_to_hdmi(encoder);
+	struct xlnx_hdmi_config *config = &hdmi->config;
+
+	xlnx_hdmi_encoder_dpms(encoder, DRM_MODE_DPMS_ON);
+	if (!config->vid_interface)
+		xlnx_hdmi_vtc_enable(hdmi);
+
+	xlnx_hdmi_ext_sysrst_deassert(hdmi);
+}
+
+static void xlnx_hdmi_encoder_disable(struct drm_encoder *encoder)
+{
+	struct xlnx_hdmi *hdmi = encoder_to_hdmi(encoder);
+	struct xlnx_hdmi_config *config = &hdmi->config;
+
+	xlnx_hdmi_encoder_dpms(encoder, DRM_MODE_DPMS_OFF);
+
+	/* Disable the EXT VRST which actually starts the bridge */
+	xlnx_hdmi_ext_sysrst_assert(hdmi);
+	if (!config->vid_interface)
+		xlnx_hdmi_vtc_disable(hdmi);
+}
+
+/**
+ * xlnx_hdmi_find_media_bus - finds drm_fourcc equivalent format
+ * @hdmi: pointer to HDMI TX core instance
+ * @drm_fourcc: drm fourcc code
+ *
+ * Returns: equivalent media bus format
+ */
+static enum
+color_formats xlnx_hdmi_find_media_bus(struct xlnx_hdmi *hdmi,
+				       u32 drm_fourcc)
+{
+	switch (drm_fourcc) {
+	case DRM_FORMAT_XBGR8888:
+	case DRM_FORMAT_XRGB8888:
+	case DRM_FORMAT_BGR888:
+	case DRM_FORMAT_RGB888:
+	case DRM_FORMAT_ARGB8888:
+	case DRM_FORMAT_ABGR8888:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_8;
+		return HDMI_TX_CSF_RGB;
+	case DRM_FORMAT_XBGR2101010:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_10;
+		return HDMI_TX_CSF_RGB;
+	case DRM_FORMAT_VUY888:
+	case DRM_FORMAT_XVUY8888:
+	case DRM_FORMAT_Y8:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_8;
+		return HDMI_TX_CSF_YCRCB_444;
+	case DRM_FORMAT_XVUY2101010:
+	case DRM_FORMAT_Y10:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_10;
+		return HDMI_TX_CSF_YCRCB_444;
+	case DRM_FORMAT_YUYV:
+	case DRM_FORMAT_UYVY:
+	case DRM_FORMAT_NV16:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_8;
+		return HDMI_TX_CSF_YCRCB_422;
+	case DRM_FORMAT_XV20:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_10;
+		return HDMI_TX_CSF_YCRCB_422;
+	case DRM_FORMAT_NV12:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_8;
+		return HDMI_TX_CSF_YCRCB_420;
+	case DRM_FORMAT_XV15:
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_10;
+		return HDMI_TX_CSF_YCRCB_420;
+	default:
+		dev_err(hdmi->dev, "Unknown drm fmt: %d\n", drm_fourcc);
+		hdmi->xvidc_colordepth = HDMI_TX_BPC_8;
+		return HDMI_TX_CSF_RGB;
+	}
+}
+
+/**
+ * xlnx_hdmi_encoder_atomic_mode_set - drive the HDMI timing parameters
+ *
+ * @encoder: pointer to Xilinx DRM encoder
+ * @crtc_state: DRM crtc state
+ * @connector_state: DRM connector state
+ *
+ * This function derives the HDMI IP timing parameters from the timing
+ * values given to timing module.
+ */
+static void
+xlnx_hdmi_encoder_atomic_mode_set(struct drm_encoder *encoder,
+				  struct drm_crtc_state *crtc_state,
+				  struct drm_connector_state *connector_state)
+{
+	struct xlnx_hdmi *hdmi = encoder_to_hdmi(encoder);
+	struct drm_connector *connector = &hdmi->connector;
+	struct xlnx_hdmi_config *config = &hdmi->config;
+	struct drm_display_mode *mode = &crtc_state->mode;
+	struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+	union phy_configure_opts phy_cfg = {0};
+	int ret, i;
+	u32 drm_fourcc, lnk_clk, vid_clk;
+
+	dev_dbg(hdmi->dev, "mode->clock = %d\n", mode->clock * 1000);
+	dev_dbg(hdmi->dev, "mode->crtc_clock = %d\n", mode->crtc_clock * 1000);
+	dev_dbg(hdmi->dev, "mode->pvsync = %d\n",
+		!!(mode->flags & DRM_MODE_FLAG_PVSYNC));
+	dev_dbg(hdmi->dev, "mode->phsync = %d\n",
+		!!(mode->flags & DRM_MODE_FLAG_PHSYNC));
+	dev_dbg(hdmi->dev, "mode->hsync_end = %d\n", mode->hsync_end);
+	dev_dbg(hdmi->dev, "mode->hsync_start = %d\n", mode->hsync_start);
+	dev_dbg(hdmi->dev, "mode->vsync_end = %d\n", mode->vsync_end);
+	dev_dbg(hdmi->dev, "mode->vsync_start = %d\n", mode->vsync_start);
+	dev_dbg(hdmi->dev, "mode->hdisplay = %d\n", mode->hdisplay);
+	dev_dbg(hdmi->dev, "mode->vdisplay = %d\n", mode->vdisplay);
+	dev_dbg(hdmi->dev, "mode->htotal = %d\n", mode->htotal);
+	dev_dbg(hdmi->dev, "mode->vtotal = %d\n", mode->vtotal);
+	dev_dbg(hdmi->dev, "mode->vrefresh = %d\n", drm_mode_vrefresh(mode));
+	dev_dbg(hdmi->dev, "mode->flags = %d interlace = %d\n", mode->flags,
+		!!(mode->flags & DRM_MODE_FLAG_INTERLACE));
+
+	if (hdmi->stream.is_frl) {
+		xlnx_hdmi_frl_reset_deassert(hdmi);
+		xlnx_hdmi_frl_intr_enable(hdmi);
+		xlnx_hdmi_frl_execute(hdmi);
+		hdmi->stream.sink_max_lanes =
+			connector->display_info.hdmi.max_lanes;
+		hdmi->stream.sink_max_linerate =
+			connector->display_info.hdmi.max_frl_rate_per_lane;
+	} else {
+		xlnx_hdmi_frl_ext_vidsrc(hdmi);
+		xlnx_hdmi_frl_sleep(hdmi);
+	}
+
+	drm_fourcc = encoder->crtc->primary->state->fb->format->format;
+	hdmi->xvidc_colorfmt = xlnx_hdmi_find_media_bus(hdmi, drm_fourcc);
+	dev_dbg(hdmi->dev, "xvidc_colorfmt = %d\n", hdmi->xvidc_colorfmt);
+	dev_dbg(hdmi->dev, "xvidc_colordepth = %d\n", hdmi->xvidc_colordepth);
+
+	hdmi->tmds_clk = adjusted_mode->clock * 1000;
+	dev_dbg(hdmi->dev, "tmds_clk = %u\n", hdmi->tmds_clk);
+
+	if (hdmi->stream.is_frl) {
+		phy_cfg.hdmi.clkout1_obuftds = 1;
+		phy_cfg.hdmi.clkout1_obuftds_en = false;
+		for (i = 0; i < HDMI_MAX_LANES; i++) {
+			ret = phy_configure(hdmi->phy[i], &phy_cfg);
+			if (ret) {
+				dev_err(hdmi->dev, "phy_cfg:10bufds_en err\n");
+				return;
+			}
+		}
+	}
+
+	xlnx_hdmi_stream_start(hdmi);
+	/* get tmds clock from phy */
+	if (!hdmi->stream.is_frl) {
+		xlnx_hdmi_clkratio(hdmi);
+
+		/* Assert VID_IN bridge resets */
+		xlnx_hdmi_ext_sysrst_assert(hdmi);
+		xlnx_hdmi_ext_vrst_assert(hdmi);
+
+		/* Assert HDMI TXCore resets */
+		xlnx_hdmi_int_lrst_assert(hdmi);
+		xlnx_hdmi_int_vrst_assert(hdmi);
+
+		phy_cfg.hdmi.tx_params = 1;
+		phy_cfg.hdmi.ppc = config->ppc;
+		phy_cfg.hdmi.bpc = config->bpc;
+		phy_cfg.hdmi.fmt = hdmi->xvidc_colorfmt;
+		phy_cfg.hdmi.tx_tmdsclk = hdmi->tmds_clk;
+		for (i = 0; i < HDMI_MAX_LANES; i++) {
+			ret = phy_configure(hdmi->phy[i], &phy_cfg);
+			if (ret) {
+				dev_err(hdmi->dev, "phy_config: set txparams error %d\n", ret);
+				return;
+			}
+		}
+	} else {
+		lnk_clk = adjusted_mode->clock / config->ppc;
+		vid_clk = lnk_clk;
+
+		xlnx_set_frl_link_clk(hdmi, lnk_clk);
+		xlnx_set_frl_vid_clk(hdmi, vid_clk);
+
+		xlnx_hdmi_aux_enable(hdmi);
+		xlnx_hdmi_start_frl_train(hdmi, hdmi->config.max_frl_rate);
+		xlnx_hdmi_auxintr_enable(hdmi);
+		xlnx_hdmi_set_samplerate(hdmi, 1);
+
+		/* release vid_in bridge resets */
+		xlnx_hdmi_ext_sysrst_deassert(hdmi);
+		xlnx_hdmi_ext_vrst_deassert(hdmi);
+		/* release tx cor resets */
+		xlnx_hdmi_int_lrst_deassert(hdmi);
+		xlnx_hdmi_int_vrst_deassert(hdmi);
+		xlnx_pioout_bridge_yuv_clr(hdmi);
+		xlnx_pioout_bridge_pixel_clr(hdmi);
+	}
+
+	dev_dbg(hdmi->dev, "mode->clock = %u Hz\n", adjusted_mode->clock);
+
+	hdmi->wait_for_streamup = 0;
+	wait_event_timeout(hdmi->wait_event, hdmi->wait_for_streamup,
+			   msecs_to_jiffies(1000));
+	if (!hdmi->wait_for_streamup)
+		dev_err(hdmi->dev, "wait_for_streamup timeout\n");
+
+	ret = xlnx_hdmi_readl(hdmi, HDMI_TX_PIO_IN);
+	if (ret & HDMI_TX_PIO_IN_VID_RDY) {
+		dev_dbg(hdmi->dev, "TX: Video ready interrupt received\n");
+		if (!config->vid_interface)
+			xlnx_hdmi_vtc_set_timing(hdmi, adjusted_mode);
+		if (hdmi->stream.is_frl)
+			xlnx_hdmi_vtc_writel(hdmi, HDMI_TX_VTC_CTL,
+					     HDMI_TX_VTC_CTL_GE);
+	} else {
+		dev_dbg(hdmi->dev, "video ready interrupt not received\n");
+	}
+
+	if (hdmi->stream.is_frl)
+		xlnx_hdmi_set_frl_active(hdmi,
+					 HDMI_TX_FRL_ACTIVE_MODE_FULL_STREAM);
+	else
+		xlnx_hdmi_ext_sysrst_assert(hdmi);
+}
+
+static const struct drm_encoder_funcs xlnx_hdmi_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+static const struct
+drm_encoder_helper_funcs xlnx_hdmi_encoder_helper_funcs = {
+	.dpms = xlnx_hdmi_encoder_dpms,
+	.enable = xlnx_hdmi_encoder_enable,
+	.disable = xlnx_hdmi_encoder_disable,
+	.atomic_mode_set = xlnx_hdmi_encoder_atomic_mode_set,
+};
+
+static int xlnx_hdmi_create_connector(struct drm_encoder *encoder)
+{
+	struct xlnx_hdmi *hdmi = encoder_to_hdmi(encoder);
+	struct drm_connector *connector = &hdmi->connector;
+	int ret;
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+	connector->interlace_allowed = true;
+
+	ret = drm_connector_init(encoder->dev, connector,
+				 &xlnx_hdmi_connector_funcs,
+				 DRM_MODE_CONNECTOR_HDMIA);
+	if (ret) {
+		dev_err(hdmi->dev, "Failed to initialize connector with drm\n");
+		return ret;
+	}
+
+	drm_connector_helper_add(connector, &xlnx_hdmi_connector_helper_funcs);
+	ret = drm_connector_register(connector);
+	if (ret) {
+		dev_err(hdmi->dev,
+			"Failed to register connector (ret=%d)\n", ret);
+		return ret;
+	}
+	ret = drm_connector_attach_encoder(connector, encoder);
+	if (ret) {
+		dev_err(hdmi->dev,
+			"Failed to attach connector (ret=%d)\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xlnx_hdmi_bind(struct device *dev, struct device *master,
+			  void *data)
+{
+	struct xlnx_hdmi *hdmi = dev_get_drvdata(dev);
+	struct drm_encoder *encoder = &hdmi->encoder;
+	struct drm_device *drm_dev = data;
+	int ret;
+
+	encoder->possible_crtcs = 1;
+	/* initialize encoder */
+	drm_encoder_init(drm_dev, encoder, &xlnx_hdmi_encoder_funcs,
+			 DRM_MODE_ENCODER_TMDS, NULL);
+	drm_encoder_helper_add(encoder, &xlnx_hdmi_encoder_helper_funcs);
+
+	/* create connector */
+	ret = xlnx_hdmi_create_connector(encoder);
+	if (ret) {
+		dev_err(hdmi->dev, "failed create connector, ret = %d\n", ret);
+		drm_encoder_cleanup(encoder);
+	}
+
+	return ret;
+}
+
+static void xlnx_hdmi_unbind(struct device *dev, struct device *master,
+			     void *data)
+{
+	struct xlnx_hdmi *hdmi = dev_get_drvdata(dev);
+
+	xlnx_hdmi_encoder_dpms(&hdmi->encoder, DRM_MODE_DPMS_OFF);
+	drm_encoder_cleanup(&hdmi->encoder);
+	drm_connector_cleanup(&hdmi->connector);
+}
+
+static const struct component_ops xlnx_hdmi_component_ops = {
+	.bind	= xlnx_hdmi_bind,
+	.unbind	= xlnx_hdmi_unbind
+};
+
+/**
+ * xlnx_hdmi_reset - Reset the core and bridge
+ * @hdmi: HDMI core structure
+ *
+ * Returns: None
+ */
+static void xlnx_hdmi_reset(struct xlnx_hdmi *hdmi)
+{
+	/* hdmi core reset - assert */
+	xlnx_hdmi_int_lrst_assert(hdmi);
+	xlnx_hdmi_int_vrst_assert(hdmi);
+
+	/* vid out bridge reset */
+	xlnx_hdmi_ext_sysrst_assert(hdmi);
+	xlnx_hdmi_ext_vrst_assert(hdmi);
+
+	/* release vid in bridge resets */
+	xlnx_hdmi_ext_sysrst_deassert(hdmi);
+	xlnx_hdmi_ext_vrst_deassert(hdmi);
+
+	/* release hdmi tx core resets */
+	xlnx_hdmi_int_lrst_deassert(hdmi);
+	xlnx_hdmi_int_vrst_deassert(hdmi);
+}
+
+/**
+ * xlnx_hdmi_exit_phy - Exit the phy
+ * @hdmi: HDMI core structure
+ *
+ * Exit the phy.
+ */
+static void xlnx_hdmi_exit_phy(struct xlnx_hdmi *hdmi)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < HDMI_MAX_LANES; i++) {
+		ret = phy_exit(hdmi->phy[i]);
+		if (ret)
+			dev_err(hdmi->dev, "fail to exit phy(%d) %d\n", i, ret);
+		hdmi->phy[i] = NULL;
+	}
+}
+
+/**
+ * xlnx_hdmi_initialize - Initializes the hdmi core
+ * @hdmi: HDMI core strcture
+ *
+ * Return: 0 on success, error code on failure
+ */
+static int xlnx_hdmi_initialize(struct xlnx_hdmi *hdmi)
+{
+	union phy_configure_opts phy_cfg = {0};
+	int ret, i;
+	unsigned long val, clkrate;
+
+	/* mutex that protects against concurrent access */
+	mutex_init(&hdmi->hdmi_mutex);
+	spin_lock_init(&hdmi->irq_lock);
+	init_waitqueue_head(&hdmi->wait_event);
+
+	/* set default color format to RGB */
+	hdmi->xvidc_colorfmt = HDMI_TX_CSF_RGB;
+
+	/* Reset all peripherals */
+	xlnx_hdmi_piointr_disable(hdmi);
+	xlnx_hdmi_ddc_disable(hdmi);
+	xlnx_hdmi_audio_disable(hdmi);
+	xlnx_hdmi_aux_disable(hdmi);
+	xlnx_hdmi_frl_intr_disable(hdmi);
+	xlnx_hdmi_frl_clear(hdmi);
+	xlnx_hdmi_piointr_clear(hdmi);
+	xlnx_hdmi_ddc_intr_clear(hdmi);
+
+	/* PIO: Set event rising edge masks */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_IN_EVT_RE,
+			 HDMI_TX_PIO_IN_BRIDGE_UFLOW |
+			 HDMI_TX_PIO_IN_BRIDGE_OFLOW |
+			 HDMI_TX_PIO_IN_BRIDGE_LOCKED |
+			 HDMI_TX_PIO_IN_HPD_TOGGLE |
+			 HDMI_TX_PIO_IN_HPD_CONNECT |
+			 HDMI_TX_PIO_IN_VS |
+			 HDMI_TX_PIO_IN_LNK_RDY);
+	/* PIO: Set event falling edge masks */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_PIO_IN_EVT_FE,
+			 HDMI_TX_PIO_IN_BRIDGE_LOCKED |
+			 HDMI_TX_PIO_IN_HPD_CONNECT |
+			 HDMI_TX_PIO_IN_LNK_RDY);
+
+	/* Set the Timegrid for HPD */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_HPD_TIMEGRID, HDMI_TX_TIMEGRID_VAL);
+	xlnx_hdmi_writel(hdmi, HDMI_TX_HPD_TOGGLE_CONF,
+			 HDMI_TX_TOGGLE_CONF_VAL);
+	xlnx_hdmi_writel(hdmi, HDMI_TX_HPD_CONNECT_CONF,
+			 HDMI_TX_CONNECT_CONF_VAL);
+
+	xlnx_hdmi_set_hdmi_mode(hdmi);
+	xlnx_hdmi_aux_enable(hdmi);
+
+	/* ddc init */
+	clkrate = clk_get_rate(hdmitx_clks[S_AXI_CPU_ACLK].clk);
+	val = (clkrate / HDMI_TX_DDC_CLKDIV) / 2;
+	val = (val << HDMI_TX_DDC_CTRL_CLK_DIV_SHIFT) &
+		HDMI_TX_DDC_CTRL_CLK_DIV;
+
+	/* Update DDC Control register */
+	xlnx_hdmi_writel(hdmi, HDMI_TX_DDC_CTRL, val);
+
+	xlnx_hdmi_frl_reset(hdmi);
+	xlnx_hdmi_set_hdmi_mode(hdmi);
+	xlnx_hdmi_aux_enable(hdmi);
+
+	xlnx_hdmi_reset(hdmi);
+
+	phy_cfg.hdmi.config_hdmi20 = 1;
+	for (i = 0; i < HDMI_MAX_LANES; i++) {
+		ret = phy_configure(hdmi->phy[i], &phy_cfg);
+		if (ret) {
+			dev_err(hdmi->dev, "phy_cfg: hdmi20 err\n");
+			return ret;
+		}
+	}
+
+	/* Enable Interrupts */
+	xlnx_hdmi_piointr_ie_enable(hdmi);
+	xlnx_hdmi_piointr_run_enable(hdmi);
+
+	return 0;
+}
+
+static int xlnx_hdmi_parse_of(struct xlnx_hdmi *hdmi)
+{
+	struct xlnx_hdmi_config *config = &hdmi->config;
+	struct device_node *node = hdmi->dev->of_node;
+	int ret;
+	u32 ppc, bpc, vid, frl_rate;
+
+	ret = of_property_read_u32(node, "xlnx,input-pixels-per-clock", &ppc);
+	if (ret || (ppc != HDMI_TX_PPC_4 && ppc != HDMI_TX_PPC_8)) {
+		dev_err(hdmi->dev, "missing or invalid pixels per clock dt prop\n");
+		return -EINVAL;
+	}
+	config->ppc = ppc;
+
+	ret = of_property_read_u32(node, "xlnx,max-bits-per-component", &bpc);
+	if (ret || (bpc != HDMI_TX_BPC_8 && bpc != HDMI_TX_BPC_10 &&
+		    bpc != HDMI_TX_BPC_12 && bpc != HDMI_TX_BPC_16)) {
+		dev_err(hdmi->dev, "missing or invalid max bpc dt prop\n");
+		return -EINVAL;
+	}
+	config->bpc = bpc;
+
+	ret = of_property_read_u32(node, "xlnx,vid-interface", &vid);
+	if (ret || (vid != HDMI_TX_AXI_STREAM && vid != HDMI_TX_NATIVE &&
+		    vid != HDMI_TX_NATIVE_IDE)) {
+		dev_err(hdmi->dev, "missing or unsupported video interface\n");
+		return -EINVAL;
+	}
+	config->vid_interface = vid;
+
+	ret = of_property_read_u32(node, "xlnx,max-frl-rate", &frl_rate);
+	if (ret || frl_rate > HDMI_TX_MAX_FRL_RATE) {
+		dev_err(hdmi->dev, "missing or unsupported frl rate\n");
+		return -EINVAL;
+	}
+	config->max_frl_rate = frl_rate;
+
+	return 0;
+}
+
+static int xlnx_hdmi_probe(struct platform_device *pdev)
+{
+	struct xlnx_hdmi *hdmi;
+	struct resource *res;
+	unsigned int index;
+	int ret, num_clks = ARRAY_SIZE(hdmitx_clks);
+
+	hdmi = devm_kzalloc(&pdev->dev, sizeof(*hdmi), GFP_KERNEL);
+	if (!hdmi)
+		return -ENOMEM;
+
+	hdmi->dpms = DRM_MODE_DPMS_OFF;
+	hdmi->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hdmi->base = devm_ioremap_resource(hdmi->dev, res);
+	if (IS_ERR(hdmi->base))
+		return PTR_ERR(hdmi->base);
+
+	ret = xlnx_hdmi_parse_of(hdmi);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_bulk_get(&pdev->dev, num_clks, hdmitx_clks);
+	if (ret)
+		return ret;
+
+	ret = clk_bulk_prepare_enable(num_clks, hdmitx_clks);
+	if (ret)
+		goto err_clk_put;
+
+	/* acquire hdmi phy lanes */
+	for (index = 0; index < HDMI_MAX_LANES; index++) {
+		char phy_name[16];
+
+		snprintf(phy_name, sizeof(phy_name), "hdmi-phy%d", index);
+		hdmi->phy[index] = devm_phy_get(hdmi->dev, phy_name);
+		if (IS_ERR(hdmi->phy[index])) {
+			dev_err(hdmi->dev, "failed to get hdmi phy\n");
+			ret = PTR_ERR(hdmi->phy[index]);
+			goto err_clk_put;
+		}
+		ret = phy_init(hdmi->phy[index]);
+		if (ret) {
+			dev_err(hdmi->dev, "failed to init hdmi phy\n");
+			goto error_phy;
+		}
+	}
+
+	dev_dbg(hdmi->dev, "axi_cpu_aclk = %lu Hz\n",
+		clk_get_rate(hdmitx_clks[S_AXI_CPU_ACLK].clk));
+	dev_dbg(hdmi->dev, "link clk = %lu Hz\n",
+		clk_get_rate(hdmitx_clks[LINK_CLK].clk));
+	dev_dbg(hdmi->dev, "video clk = %lu Hz\n",
+		clk_get_rate(hdmitx_clks[VIDEO_CLK].clk));
+	dev_dbg(hdmi->dev, "frl clk = %lu Hz\n",
+		clk_get_rate(hdmitx_clks[FRL_CLK].clk));
+	dev_dbg(hdmi->dev, "video aclk rate = %lu Hz\n",
+		clk_get_rate(hdmitx_clks[S_AXIS_VIDEO_ACLK].clk));
+
+	hdmi->irq = platform_get_irq(pdev, 0);
+	if (hdmi->irq < 0) {
+		dev_err(hdmi->dev, "platform_get_irq() failed\n");
+		ret = hdmi->irq;
+		goto error_phy;
+	}
+
+	/* Request the interrupt */
+	ret = devm_request_threaded_irq(hdmi->dev, hdmi->irq,
+					hdmitx_irq_handler, hdmitx_irq_thread,
+					IRQF_TRIGGER_HIGH,
+					"xilinx-hdmitxss", hdmi/* dev_id */);
+	if (ret) {
+		dev_err(hdmi->dev, "unable to request IRQ %d\n", hdmi->irq);
+		goto error_phy;
+	}
+
+	platform_set_drvdata(pdev, hdmi);
+
+	/* initialize hw */
+	ret = xlnx_hdmi_initialize(hdmi);
+	if (ret) {
+		dev_err(hdmi->dev, "hdmi initialization failed\n");
+		goto error_phy;
+	}
+
+	return component_add(hdmi->dev, &xlnx_hdmi_component_ops);
+
+error_phy:
+	dev_dbg(hdmi->dev, "probe failed:: error_phy:\n");
+	xlnx_hdmi_exit_phy(hdmi);
+	clk_bulk_disable_unprepare(num_clks, hdmitx_clks);
+err_clk_put:
+	clk_bulk_put(num_clks, hdmitx_clks);
+
+	return ret;
+}
+
+static int xlnx_hdmi_remove(struct platform_device *pdev)
+{
+	struct xlnx_hdmi *hdmi = platform_get_drvdata(pdev);
+	int num_clks = ARRAY_SIZE(hdmitx_clks);
+
+	xlnx_hdmi_exit_phy(hdmi);
+	component_del(&pdev->dev, &xlnx_hdmi_component_ops);
+	clk_bulk_disable_unprepare(num_clks, hdmitx_clks);
+	clk_bulk_put(num_clks, hdmitx_clks);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_hdmi_of_match[] = {
+	{ .compatible = "xlnx,v-hdmi-txss1-1.1" },
+	{ /* end of table */ },
+};
+
+MODULE_DEVICE_TABLE(of, xlnx_hdmi_of_match);
+
+static struct platform_driver xlnx_hdmi_driver = {
+	.probe			= xlnx_hdmi_probe,
+	.remove			= xlnx_hdmi_remove,
+	.driver			= {
+		.name		= "xlnx-hdmi",
+		.of_match_table	= xlnx_hdmi_of_match,
+	},
+};
+
+module_platform_driver(xlnx_hdmi_driver);
+
+MODULE_AUTHOR("Venkateshwar Rao G <vgannava@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx DRM KMS HDMI Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_mixer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_mixer.c
@@ -0,0 +1,3178 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx logicore video mixer driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *       : Jeffrey Mouroux <jmouroux@xilinx.com>
+ */
+
+#include <drm/drm_vblank.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_atomic_uapi.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_modeset_helper_vtables.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/component.h>
+#include <linux/dma/xilinx_frmbuf.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/gpio/consumer.h>
+#include <linux/of.h>
+#include <linux/of_dma.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <video/videomode.h>
+#include "xlnx_bridge.h"
+#include "xlnx_crtc.h"
+#include "xlnx_drv.h"
+
+/**************************** Register Data **********************************/
+#define XVMIX_AP_CTRL			0x00000
+#define XVMIX_GIE			0x00004
+#define XVMIX_IER			0x00008
+#define XVMIX_ISR			0x0000c
+#define XVMIX_WIDTH_DATA		0x00010
+#define XVMIX_HEIGHT_DATA		0x00018
+#define XVMIX_BACKGROUND_Y_R_DATA	0x00028
+#define XVMIX_BACKGROUND_U_G_DATA	0x00030
+#define XVMIX_BACKGROUND_V_B_DATA	0x00038
+#define XVMIX_LAYERENABLE_DATA		0x00040
+#define XVMIX_K00_1			0x00048
+#define XVMIX_K01_1			0x00050
+#define XVMIX_K02_1			0x00058
+#define XVMIX_K10_1			0x00060
+#define XVMIX_K11_1			0x00068
+#define XVMIX_K12_1			0x00070
+#define XVMIX_K20_1			0x00078
+#define XVMIX_K21_1			0x00080
+#define XVMIX_K22_1			0x00088
+#define XVMIX_Y_DATA			0x00090
+#define XVMIX_U_DATA			0x00098
+#define XVMIX_V_DATA			0x000A0
+#define XVMIX_LAYERALPHA_0_DATA		0x00100
+#define XVMIX_LAYERSTARTX_0_DATA	0x00108
+#define XVMIX_LAYERSTARTY_0_DATA	0x00110
+#define XVMIX_LAYERWIDTH_0_DATA		0x00118
+#define XVMIX_LAYERSTRIDE_0_DATA	0x00120
+#define XVMIX_LAYERHEIGHT_0_DATA	0x00128
+#define XVMIX_LAYERSCALE_0_DATA		0x00130
+#define XVMIX_LAYERVIDEOFORMAT_0_DATA	0x00138
+#define XVMIX_K00_2			0x00140
+#define XVMIX_K01_2			0x00148
+#define XVMIX_K02_2			0x00150
+#define XVMIX_K10_2			0x00158
+#define XVMIX_K11_2			0x00160
+#define XVMIX_K12_2			0x00168
+#define XVMIX_K20_2			0x00170
+#define XVMIX_K21_2			0x00178
+#define XVMIX_K22_2			0x00180
+#define XVMIX_R_DATA			0x00188
+#define XVMIX_G_DATA			0x00190
+#define XVMIX_B_DATA			0x00198
+#define XVMIX_LAYER1_BUF1_V_DATA	0x00240
+#define XVMIX_LAYER1_BUF2_V_DATA	0x0024c
+#define XVMIX_LOGOSTARTX_DATA		0x01000
+#define XVMIX_LOGOSTARTY_DATA		0x01008
+#define XVMIX_LOGOWIDTH_DATA		0x01010
+#define XVMIX_LOGOHEIGHT_DATA		0x01018
+#define XVMIX_LOGOSCALEFACTOR_DATA	0x01020
+#define XVMIX_LOGOALPHA_DATA		0x01028
+#define XVMIX_LOGOCLRKEYMIN_R_DATA	0x01030
+#define XVMIX_LOGOCLRKEYMIN_G_DATA	0x01038
+#define XVMIX_LOGOCLRKEYMIN_B_DATA	0x01040
+#define XVMIX_LOGOCLRKEYMAX_R_DATA	0x01048
+#define XVMIX_LOGOCLRKEYMAX_G_DATA	0x01050
+#define XVMIX_LOGOCLRKEYMAX_B_DATA	0x01058
+#define XVMIX_LOGOR_V_BASE		0x10000
+#define XVMIX_LOGOR_V_HIGH		0x10fff
+#define XVMIX_LOGOG_V_BASE		0x20000
+#define XVMIX_LOGOG_V_HIGH		0x20fff
+#define XVMIX_LOGOB_V_BASE		0x30000
+#define XVMIX_LOGOB_V_HIGH		0x30fff
+#define XVMIX_LOGOA_V_BASE		0x40000
+#define XVMIX_LOGOA_V_HIGH		0x40fff
+
+/************************** Constant Definitions *****************************/
+#define XVMIX_LOGO_OFFSET		0x1000
+#define XVMIX_MASK_DISABLE_ALL_LAYERS   0x0
+#define XVMIX_REG_OFFSET                0x100
+#define XVMIX_MASTER_LAYER_IDX		0x0
+#define XVMIX_LOGO_LAYER_IDX		0x1
+#define XVMIX_DISP_MAX_WIDTH		8192
+#define XVMIX_DISP_MAX_HEIGHT		4320
+#define XVMIX_DISP_MIN_WIDTH		64
+#define XVMIX_DISP_MIN_HEIGHT		64
+#define XVMIX_MAX_OVERLAY_LAYERS	16
+#define XVMIX_MAX_BPC			16
+#define XVMIX_ALPHA_MIN			0
+#define XVMIX_ALPHA_MAX			256
+#define XVMIX_LAYER_WIDTH_MIN		64
+#define XVMIX_LAYER_HEIGHT_MIN		64
+#define XVMIX_LOGO_LAYER_WIDTH_MIN	32
+#define XVMIX_LOGO_LAYER_HEIGHT_MIN	32
+#define XVMIX_LOGO_LAYER_WIDTH_MAX	256
+#define XVMIX_LOGO_LAYER_HEIGHT_MAX	256
+#define XVMIX_IRQ_DONE_MASK		BIT(0)
+#define XVMIX_GIE_EN_MASK		BIT(0)
+#define XVMIX_AP_EN_MASK		BIT(0)
+#define XVMIX_AP_RST_MASK		BIT(7)
+#define XVMIX_MAX_NUM_SUB_PLANES	4
+#define XVMIX_SCALE_FACTOR_1X		0
+#define	XVMIX_SCALE_FACTOR_2X		1
+#define	XVMIX_SCALE_FACTOR_4X		2
+#define	XVMIX_SCALE_FACTOR_INVALID	3
+#define	XVMIX_BASE_ALIGN		8
+#define XVMIX_CSC_MAX_ROWS		(3)
+#define XVMIX_CSC_MAX_COLS		(3)
+#define XVMIX_CSC_MATRIX_SIZE	(XVMIX_CSC_MAX_ROWS * XVMIX_CSC_MAX_COLS)
+#define XVMIX_CSC_COEFF_SIZE		(12)
+#define XVMIX_CSC_SCALE_FACTOR		(4096)
+#define XVMIX_CSC_DIVISOR		(10000)
+
+/*************************** STATIC DATA  ************************************/
+static const s16
+xlnx_mix_yuv2rgb_coeffs[][DRM_COLOR_ENCODING_MAX][XVMIX_CSC_COEFF_SIZE] = {
+	[DRM_COLOR_YCBCR_BT601][DRM_COLOR_YCBCR_LIMITED_RANGE] = {
+		10000, 0, 13669,
+		10000, -3367, -6986,
+		10000, 17335, 0,
+		-175, 132, -222
+	},
+	[DRM_COLOR_YCBCR_BT601][DRM_COLOR_YCBCR_FULL_RANGE] = {
+		10479, 0, 13979,
+		10479, -3443, -7145,
+		10479, 17729, 0,
+		-179, 136, -227
+	},
+	[DRM_COLOR_YCBCR_BT709][DRM_COLOR_YCBCR_LIMITED_RANGE] = {
+		10000, 0, 15406,
+		10000, -1832, -4579,
+		10000, 18153, 0,
+		-197, 82, -232
+	},
+	[DRM_COLOR_YCBCR_BT709][DRM_COLOR_YCBCR_FULL_RANGE] = {
+		10233, 0, 15756,
+		10233, -1873, -4683,
+		10233, 18566, 0,
+		-202, 84, -238
+	},
+	[DRM_COLOR_YCBCR_BT2020][DRM_COLOR_YCBCR_LIMITED_RANGE] = {
+		10000, 0, 14426,
+		10000, -1609, -5589,
+		10000, 18406, 0,
+		-185, 92, -236
+	},
+	[DRM_COLOR_YCBCR_BT2020][DRM_COLOR_YCBCR_FULL_RANGE] = {
+		10233, 0, 14754,
+		10233, -1646, -5716,
+		10233, 18824, 0,
+		-189, 94, -241
+	}
+};
+
+static const s16
+xlnx_mix_rgb2yuv_coeffs[][DRM_COLOR_ENCODING_MAX][XVMIX_CSC_COEFF_SIZE] = {
+	[DRM_COLOR_YCBCR_BT601][DRM_COLOR_YCBCR_LIMITED_RANGE] = {
+		2990, 5870, 1440,
+		-1720, -3390, 5110,
+		5110, -4280, -830,
+		0, 128, 128
+	},
+	[DRM_COLOR_YCBCR_BT601][DRM_COLOR_YCBCR_FULL_RANGE] = {
+		2921, 5735, 1113,
+		-1686, -3310, 4393,
+		4393, -4184, -812,
+		0, 128, 128
+	},
+	[DRM_COLOR_YCBCR_BT709][DRM_COLOR_YCBCR_LIMITED_RANGE] = {
+		2120, 7150, 720,
+		-1170, -3940, 5110,
+		5110, -4640, -470,
+		0, 128, 128
+	},
+	[DRM_COLOR_YCBCR_BT709][DRM_COLOR_YCBCR_FULL_RANGE] = {
+		2077, 6988, 705,
+		-1144, -3582, 4997,
+		4997, -4538, -458,
+		0, 128, 128
+	},
+	[DRM_COLOR_YCBCR_BT2020][DRM_COLOR_YCBCR_LIMITED_RANGE] = {
+		2625, 6775, 592,
+		-1427, -3684, 5110,
+		5110, -4699, -410,
+		0, 128, 128
+	},
+	[DRM_COLOR_YCBCR_BT2020][DRM_COLOR_YCBCR_FULL_RANGE] = {
+		2566, 6625, 579,
+		-1396, -3602, 4997,
+		4997, -4595, -401,
+		0, 128, 128
+	}
+};
+
+static const u32 color_table[] = {
+	DRM_FORMAT_BGR888,
+	DRM_FORMAT_RGB888,
+	DRM_FORMAT_XBGR2101010,
+	DRM_FORMAT_XRGB8888,
+	DRM_FORMAT_RGBA8888,
+	DRM_FORMAT_ABGR8888,
+	DRM_FORMAT_ARGB8888,
+	DRM_FORMAT_XBGR8888,
+	DRM_FORMAT_YUYV,
+	DRM_FORMAT_UYVY,
+	DRM_FORMAT_AYUV,
+	DRM_FORMAT_NV12,
+	DRM_FORMAT_NV16,
+	DRM_FORMAT_Y8,
+	DRM_FORMAT_Y10,
+	DRM_FORMAT_XVUY2101010,
+	DRM_FORMAT_VUY888,
+	DRM_FORMAT_XVUY8888,
+	DRM_FORMAT_XV15,
+	DRM_FORMAT_XV20,
+};
+
+static bool xlnx_mixer_primary_enable = true;
+module_param_named(mixer_primary_enable, xlnx_mixer_primary_enable, bool, 0600);
+MODULE_PARM_DESC(mixer_primary_enable, "Enable mixer primary plane (default: 1)");
+
+/*********************** Inline Functions/Macros *****************************/
+#define to_mixer_hw(p) (&((p)->mixer->mixer_hw))
+#define to_xlnx_crtc(x)	container_of(x, struct xlnx_crtc, crtc)
+#define to_xlnx_plane(x)	container_of(x, struct xlnx_mix_plane, base)
+#define to_xlnx_mixer(x)	container_of(x, struct xlnx_mix, crtc)
+
+/**
+ * enum xlnx_mix_layer_id - Describes the layer by index to be acted upon
+ * @XVMIX_LAYER_MASTER: Master layer
+ * @XVMIX_LAYER_1: Layer 1
+ * @XVMIX_LAYER_2: Layer 2
+ * @XVMIX_LAYER_3: Layer 3
+ * @XVMIX_LAYER_4: Layer 4
+ * @XVMIX_LAYER_5: Layer 5
+ * @XVMIX_LAYER_6: Layer 6
+ * @XVMIX_LAYER_7: Layer 7
+ * @XVMIX_LAYER_8: Layer 8
+ * @XVMIX_LAYER_9: Layer 9
+ * @XVMIX_LAYER_10: Layer 10
+ * @XVMIX_LAYER_11: Layer 11
+ * @XVMIX_LAYER_12: Layer 12
+ * @XVMIX_LAYER_13: Layer 13
+ * @XVMIX_LAYER_14: Layer 14
+ * @XVMIX_LAYER_15: Layer 15
+ * @XVMIX_LAYER_16: Layer 16
+ */
+enum xlnx_mix_layer_id {
+	XVMIX_LAYER_MASTER = 0,
+	XVMIX_LAYER_1,
+	XVMIX_LAYER_2,
+	XVMIX_LAYER_3,
+	XVMIX_LAYER_4,
+	XVMIX_LAYER_5,
+	XVMIX_LAYER_6,
+	XVMIX_LAYER_7,
+	XVMIX_LAYER_8,
+	XVMIX_LAYER_9,
+	XVMIX_LAYER_10,
+	XVMIX_LAYER_11,
+	XVMIX_LAYER_12,
+	XVMIX_LAYER_13,
+	XVMIX_LAYER_14,
+	XVMIX_LAYER_15,
+	XVMIX_LAYER_16
+};
+
+/**
+ * struct xlnx_mix_layer_data - Describes the hardware configuration of a given
+ * mixer layer
+ * @hw_config: struct specifying the IP hardware constraints for this layer
+ * @vid_fmt: DRM format for this layer
+ * @can_alpha: Indicates that layer alpha is enabled for this layer
+ * @can_scale: Indicates that layer scaling is enabled for this layer
+ * @is_streaming: Indicates layer is not using mixer DMA but streaming from
+ *  external DMA
+ * @max_width: Max possible pixel width
+ * @max_height: Max possible pixel height
+ * @min_width: Min possible pixel width
+ * @min_height: Min possible pixel height
+ * @layer_regs: struct containing current cached register values
+ * @buff_addr: Current physical address of image buffer
+ * @x_pos: Current CRTC x offset
+ * @y_pos: Current CRTC y offset
+ * @width: Current width in pixels
+ * @height: Current hight in pixels
+ * @stride: Current stride (when Mixer is performing DMA)
+ * @alpha: Current alpha setting
+ * @is_active: Logical flag indicating layer in use.  If false, calls to
+ *  enable layer will be ignored.
+ * @scale_fact: Current scaling factor applied to layer
+ * @id: The logical layer id identifies which layer this struct describes
+ *  (e.g. 0 = master, 1-15 = overlay).
+ *
+ * All mixer layers are reprsented by an instance of this struct:
+ * output streaming, overlay, logo.
+ * Current layer-specific register state is stored in the layer_regs struct.
+ * The hardware configuration is stored in struct hw_config.
+ *
+ * Note:
+ * Some properties of the logo layer are unique and not described in this
+ * struct.  Those properites are part of the xlnx_mix struct as global
+ * properties.
+ */
+struct xlnx_mix_layer_data {
+	struct {
+		u32     vid_fmt;
+		bool    can_alpha;
+		bool    can_scale;
+		bool    is_streaming;
+		u32     max_width;
+		u32     max_height;
+		u32     min_width;
+		u32     min_height;
+	} hw_config;
+
+	struct {
+		u64     buff_addr1;
+		u64     buff_addr2;
+		u32     x_pos;
+		u32     y_pos;
+		u32     width;
+		u32     height;
+		u32     stride;
+		u32     alpha;
+		bool	is_active;
+		u32	scale_fact;
+	} layer_regs;
+
+	enum xlnx_mix_layer_id id;
+};
+
+/**
+ * struct xlnx_mix_hw - Describes a mixer IP block instance within the design
+ * @base: Base physical address of Mixer IP in memory map
+ * @logo_layer_en: Indicates logo layer is enabled in hardware
+ * @logo_pixel_alpha_enabled: Indicates that per-pixel alpha supported for logo
+ *  layer
+ * @csc_enabled: Indicates that colorimetry coefficients are programmable
+ * @max_layer_width: Max possible width for any layer on this Mixer
+ * @max_layer_height: Max possible height for any layer on this Mixer
+ * @max_logo_layer_width: Min possible width for any layer on this Mixer
+ * @max_logo_layer_height: Min possible height for any layer on this Mixer
+ * @num_layers: Max number of layers (excl: logo)
+ * @bg_layer_bpc: Bits per component for the background streaming layer
+ * @dma_addr_size: dma address size in bits
+ * @ppc: Pixels per component
+ * @irq: Interrupt request number assigned
+ * @bg_color: Current RGB color value for internal background color generator
+ * @layer_data: Array of layer data
+ * @layer_cnt: Layer data array count
+ * @max_layers: Maximum number of layers supported by hardware
+ * @logo_layer_id: Index of logo layer
+ * @logo_en_mask: Mask used to enable logo layer
+ * @enable_all_mask: Mask used to enable all layers
+ * @reset_gpio: GPIO line used to reset IP between modesetting operations
+ * @intrpt_handler_fn: Interrupt handler function called when frame is completed
+ * @intrpt_data: Data pointer passed to interrupt handler
+ *
+ * Used as the primary data structure for many L2 driver functions. Logo layer
+ * data, if enabled within the IP, is described in this structure.  All other
+ * layers are described by an instance of xlnx_mix_layer_data referenced by this
+ * struct.
+ *
+ */
+struct xlnx_mix_hw {
+	void __iomem        *base;
+	bool                logo_layer_en;
+	bool                logo_pixel_alpha_enabled;
+	u32		    csc_enabled;
+	u32                 max_layer_width;
+	u32                 max_layer_height;
+	u32                 max_logo_layer_width;
+	u32                 max_logo_layer_height;
+	u32                 num_layers;
+	u32                 bg_layer_bpc;
+	u32		    dma_addr_size;
+	u32                 ppc;
+	int		    irq;
+	u64		    bg_color;
+	struct xlnx_mix_layer_data *layer_data;
+	u32 layer_cnt;
+	u32 max_layers;
+	u32 logo_layer_id;
+	u32 logo_en_mask;
+	u32 enable_all_mask;
+	struct gpio_desc *reset_gpio;
+	void (*intrpt_handler_fn)(void *);
+	void *intrpt_data;
+};
+
+/**
+ * struct xlnx_mix - Container for interfacing DRM driver to mixer
+ * @mixer_hw: Object representing actual hardware state of mixer
+ * @master: Logical master device from xlnx drm
+ * @crtc: Xilinx DRM driver crtc object
+ * @drm_primary_layer: Hardware layer serving as logical DRM primary layer
+ * @hw_master_layer: Base video streaming layer
+ * @hw_logo_layer: Hardware logo layer
+ * @planes: Mixer overlay layers
+ * @num_planes : number of planes
+ * @max_width : maximum width of plane
+ * @max_height : maximum height of plane
+ * @max_cursor_width : maximum cursor width
+ * @max_cursor_height: maximum cursor height
+ * @alpha_prop: Global layer alpha property
+ * @scale_prop: Layer scale property (1x, 2x or 4x)
+ * @bg_color: Background color property for primary layer
+ * @drm: core drm object
+ * @pixel_clock: pixel clock for mixer
+ * @pixel_clock_enabled: pixel clock status
+ * @dpms: mixer drm state
+ * @event: vblank pending event
+ * @vtc_bridge: vtc_bridge structure
+ * @disp_bridge: disp_bridge structure
+ *
+ * Contains pointers to logical constructions such as the DRM plane manager as
+ * well as pointers to distinquish the mixer layer serving as the DRM "primary"
+ * plane from the actual mixer layer which serves as the background layer in
+ * hardware.
+ *
+ */
+struct xlnx_mix {
+	struct xlnx_mix_hw mixer_hw;
+	struct platform_device *master;
+	struct xlnx_crtc crtc;
+	struct xlnx_mix_plane *drm_primary_layer;
+	struct xlnx_mix_plane *hw_master_layer;
+	struct xlnx_mix_plane *hw_logo_layer;
+	struct xlnx_mix_plane *planes;
+	u32 num_planes;
+	u32 max_width;
+	u32 max_height;
+	u32 max_cursor_width;
+	u32 max_cursor_height;
+	struct drm_property *alpha_prop;
+	struct drm_property *scale_prop;
+	struct drm_property *bg_color;
+	struct drm_device *drm;
+	struct clk *pixel_clock;
+	bool pixel_clock_enabled;
+	int dpms;
+	struct drm_pending_vblank_event *event;
+	struct xlnx_bridge *vtc_bridge;
+	struct xlnx_bridge *disp_bridge;
+};
+
+/**
+ * struct xlnx_mix_plane_dma - Xilinx drm plane VDMA object
+ *
+ * @chan: dma channel
+ * @xt: dma interleaved configuration template
+ * @sgl: data chunk for dma_interleaved_template
+ * @is_active: flag if the DMA is active
+ */
+struct xlnx_mix_plane_dma {
+	struct dma_chan *chan;
+	struct dma_interleaved_template xt;
+	struct data_chunk sgl[1];
+	bool is_active;
+};
+
+/**
+ * struct xlnx_mix_plane - Xilinx drm plane object
+ *
+ * @base: base drm plane object
+ * @mixer_layer: video mixer hardware layer data instance
+ * @mixer: mixer DRM object
+ * @dma: dma object
+ * @id: plane id
+ * @dpms: current dpms level
+ * @format: pixel format
+ */
+struct xlnx_mix_plane {
+	struct drm_plane base;
+	struct xlnx_mix_layer_data *mixer_layer;
+	struct xlnx_mix *mixer;
+	struct xlnx_mix_plane_dma dma[XVMIX_MAX_NUM_SUB_PLANES];
+	int id;
+	int dpms;
+	u32 format;
+};
+
+static inline void reg_writel(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static inline void reg_writeq(void __iomem *base, int offset, u64 val)
+{
+	writel(lower_32_bits(val), base + offset);
+	writel(upper_32_bits(val), base + offset + 4);
+}
+
+static inline u32 reg_readl(void __iomem *base, int offset)
+{
+	return readl(base + offset);
+}
+
+static u32 xlnx_mix_get_bus_fmt(struct xlnx_mix *mixer)
+{
+	struct xlnx_mix_layer_data *master;
+
+	master = &mixer->mixer_hw.layer_data[XVMIX_MASTER_LAYER_IDX];
+
+	switch (master->hw_config.vid_fmt) {
+	case DRM_FORMAT_BGR888:
+	case DRM_FORMAT_RGB888:
+	case DRM_FORMAT_XRGB8888:
+	case DRM_FORMAT_RGBA8888:
+	case DRM_FORMAT_ABGR8888:
+	case DRM_FORMAT_ARGB8888:
+	case DRM_FORMAT_XBGR8888:
+		return MEDIA_BUS_FMT_RBG888_1X24;
+	case DRM_FORMAT_XBGR2101010:
+		return MEDIA_BUS_FMT_RBG101010_1X30;
+	case DRM_FORMAT_YUYV:
+	case DRM_FORMAT_UYVY:
+	case DRM_FORMAT_NV16:
+		return MEDIA_BUS_FMT_UYVY8_1X16;
+	case DRM_FORMAT_AYUV:
+	case DRM_FORMAT_VUY888:
+	case DRM_FORMAT_XVUY8888:
+		return MEDIA_BUS_FMT_VUY8_1X24;
+	case DRM_FORMAT_NV12:
+		return MEDIA_BUS_FMT_VYYUYY8_1X24;
+	case DRM_FORMAT_Y8:
+		return MEDIA_BUS_FMT_Y8_1X8;
+	case DRM_FORMAT_Y10:
+		return MEDIA_BUS_FMT_Y10_1X10;
+	case DRM_FORMAT_XVUY2101010:
+		return MEDIA_BUS_FMT_VUY10_1X30;
+	case DRM_FORMAT_XV15:
+		return MEDIA_BUS_FMT_VYYUYY10_4X20;
+	case DRM_FORMAT_XV20:
+		return MEDIA_BUS_FMT_UYVY10_1X20;
+	default:
+		DRM_DEBUG_KMS("invalid layer format: %d\n",
+			      master->hw_config.vid_fmt);
+		return 0;
+	}
+}
+
+/**
+ * xlnx_mix_intrpt_enable_done - Enables interrupts
+ * @mixer: instance of mixer IP core
+ *
+ * Enables interrupts in the mixer core
+ */
+static void xlnx_mix_intrpt_enable_done(struct xlnx_mix_hw *mixer)
+{
+	u32 curr_val = reg_readl(mixer->base, XVMIX_IER);
+
+	/* Enable Interrupts */
+	reg_writel(mixer->base, XVMIX_IER, curr_val | XVMIX_IRQ_DONE_MASK);
+	reg_writel(mixer->base, XVMIX_GIE, XVMIX_GIE_EN_MASK);
+}
+
+/**
+ * xlnx_mix_intrpt_disable - Disable interrupts
+ * @mixer: instance of mixer IP core
+ *
+ * Disables interrupts in the mixer core
+ */
+static void xlnx_mix_intrpt_disable(struct xlnx_mix_hw *mixer)
+{
+	u32 curr_val =  reg_readl(mixer->base, XVMIX_IER);
+
+	reg_writel(mixer->base, XVMIX_IER, curr_val & (~XVMIX_IRQ_DONE_MASK));
+	reg_writel(mixer->base, XVMIX_GIE, 0);
+}
+
+/**
+ * xlnx_mix_start - Start the mixer core video generator
+ * @mixer: Mixer core instance for which to start video output
+ *
+ * Starts the core to generate a video frame.
+ */
+static void xlnx_mix_start(struct xlnx_mix_hw *mixer)
+{
+	u32 val;
+
+	val = XVMIX_AP_RST_MASK | XVMIX_AP_EN_MASK;
+	reg_writel(mixer->base, XVMIX_AP_CTRL, val);
+}
+
+/**
+ * xlnx_mix_stop - Stop the mixer core video generator
+ * @mixer: Mixer core instance for which to stop video output
+ *
+ * Starts the core to generate a video frame.
+ */
+static void xlnx_mix_stop(struct xlnx_mix_hw *mixer)
+{
+	reg_writel(mixer->base, XVMIX_AP_CTRL, 0);
+}
+
+static inline uint32_t xlnx_mix_get_intr_status(struct xlnx_mix_hw *mixer)
+{
+	return reg_readl(mixer->base, XVMIX_ISR) & XVMIX_IRQ_DONE_MASK;
+}
+
+static inline void xlnx_mix_clear_intr_status(struct xlnx_mix_hw *mixer,
+					      uint32_t intr)
+{
+	reg_writel(mixer->base, XVMIX_ISR, intr);
+}
+
+/**
+ * xlnx_mix_set_yuv2_rgb_coeff - Programs yuv to rgb coeffiecients
+ * @plane: Xilinx drm plane object
+ * @enc: Colorimetry encoding scheme
+ * @range: Colorimetry range
+ * Programs the colorimetry coefficients required for yuv to rgb
+ * conversion.
+ */
+static void xlnx_mix_set_yuv2_rgb_coeff(struct xlnx_mix_plane *plane,
+					enum drm_color_encoding enc,
+					enum drm_color_range range)
+{
+	struct xlnx_mix *mixer = plane->mixer;
+	u32 i;
+	u32 bpc_scale = 1 << (mixer->mixer_hw.bg_layer_bpc - 8);
+
+	for (i = 0; i < XVMIX_CSC_MATRIX_SIZE; i++)
+		reg_writel(mixer->mixer_hw.base, XVMIX_K00_1 + i * 8,
+			   xlnx_mix_yuv2rgb_coeffs[enc][range][i] *
+			   XVMIX_CSC_SCALE_FACTOR / XVMIX_CSC_DIVISOR);
+
+	for (i = XVMIX_CSC_MATRIX_SIZE; i < XVMIX_CSC_COEFF_SIZE; i++)
+		reg_writel(mixer->mixer_hw.base, XVMIX_K00_1 + i * 8,
+			   (xlnx_mix_yuv2rgb_coeffs[enc][range][i] *
+			    bpc_scale));
+}
+
+/**
+ * xlnx_mix_set_rgb2_yuv_coeff - Programs rgb to yuv coeffiecients
+ * @plane: Xilinx drm plane object
+ * @enc: Colorimetry encoding scheme
+ * @range: Colorimetry range
+ * Programs the colorimetry coefficients required for rgb to yuv
+ * conversion.
+ */
+static void xlnx_mix_set_rgb2_yuv_coeff(struct xlnx_mix_plane *plane,
+					enum drm_color_encoding enc,
+					enum drm_color_range range)
+{
+	struct xlnx_mix *mixer = plane->mixer;
+	u32 i;
+	u32 bpc_scale = 1 << (mixer->mixer_hw.bg_layer_bpc - 8);
+
+	for (i = 0; i < XVMIX_CSC_MATRIX_SIZE; i++)
+		reg_writel(mixer->mixer_hw.base, XVMIX_K00_2 + i * 8,
+			   xlnx_mix_rgb2yuv_coeffs[enc][range][i] *
+			   XVMIX_CSC_SCALE_FACTOR / XVMIX_CSC_DIVISOR);
+
+	for (i = XVMIX_CSC_MATRIX_SIZE; i < XVMIX_CSC_COEFF_SIZE; i++)
+		reg_writel(mixer->mixer_hw.base, XVMIX_K00_2 + i * 8,
+			   (xlnx_mix_rgb2yuv_coeffs[enc][range][i] *
+			    bpc_scale));
+}
+
+/**
+ * xlnx_mix_get_layer_data - Retrieve current hardware and register
+ * values for a logical video layer
+ * @mixer: Mixer instance to interrogate
+ * @id: Id of layer for which data is requested
+ *
+ * Return:
+ * Structure containing layer-specific data; NULL upon failure
+ */
+static struct xlnx_mix_layer_data *
+xlnx_mix_get_layer_data(struct xlnx_mix_hw *mixer, enum xlnx_mix_layer_id id)
+{
+	u32 i;
+	struct xlnx_mix_layer_data *layer_data;
+
+	for (i = 0; i <= (mixer->layer_cnt - 1); i++) {
+		layer_data = &mixer->layer_data[i];
+		if (layer_data->id == id)
+			return layer_data;
+	}
+	return NULL;
+}
+
+/**
+ * xlnx_mix_set_active_area - Sets the number of active horizontal and
+ * vertical scan lines for the mixer background layer.
+ * @mixer: Mixer instance for which to set a new viewable area
+ * @hactive: Width of new background image dimension
+ * @vactive: Height of new background image dimension
+ *
+ * Minimum values are 64x64 with maximum values determined by the IP hardware
+ * design.
+ *
+ * Return:
+ * Zero on success, -EINVAL on failure
+ */
+static int xlnx_mix_set_active_area(struct xlnx_mix_hw *mixer,
+				    u32 hactive, u32 vactive)
+{
+	struct xlnx_mix_layer_data *ld =
+		xlnx_mix_get_layer_data(mixer, XVMIX_LAYER_MASTER);
+
+	if (hactive > ld->hw_config.max_width ||
+	    vactive > ld->hw_config.max_height) {
+		DRM_ERROR("Invalid layer dimension\n");
+		return -EINVAL;
+	}
+	/* set resolution */
+	reg_writel(mixer->base, XVMIX_HEIGHT_DATA, vactive);
+	reg_writel(mixer->base, XVMIX_WIDTH_DATA, hactive);
+	ld->layer_regs.width  = hactive;
+	ld->layer_regs.height = vactive;
+
+	return 0;
+}
+
+/**
+ * is_window_valid - Validate requested plane dimensions
+ * @mixer: Mixer core instance for which to stop video output
+ * @x_pos: x position requested for start of plane
+ * @y_pos: y position requested for start of plane
+ * @width: width of plane
+ * @height: height of plane
+ * @scale: scale factor of plane
+ *
+ * Validates if the requested window is within the frame boundary
+ *
+ * Return:
+ * true on success, false on failure
+ */
+static bool is_window_valid(struct xlnx_mix_hw *mixer, u32 x_pos, u32 y_pos,
+			    u32 width, u32 height, u32 scale)
+{
+	struct xlnx_mix_layer_data *master_layer;
+	int scale_factor[3] = {1, 2, 4};
+
+	master_layer = xlnx_mix_get_layer_data(mixer, XVMIX_LAYER_MASTER);
+
+	/* Check if window scale factor is set */
+	if (scale < XVMIX_SCALE_FACTOR_INVALID) {
+		width  *= scale_factor[scale];
+		height *= scale_factor[scale];
+	}
+
+	/* verify overlay falls within currently active background area */
+	if (((x_pos + width)  <= master_layer->layer_regs.width) &&
+	    ((y_pos + height) <= master_layer->layer_regs.height))
+		return true;
+
+	DRM_ERROR("Requested plane dimensions can't be set\n");
+	return false;
+}
+
+/**
+ *  xlnx_mix_layer_enable - Enables the requested layers
+ * @mixer: Mixer instance in which to enable a video layer
+ * @id: Logical id (e.g. 16 = logo layer) to enable
+ *
+ * Enables (permit video output) for layers in mixer
+ * Enables the layer denoted by id in the IP core.
+ * Layer 0 will indicate the background layer and layer 8 the logo
+ * layer. Passing max layers value will enable all
+ */
+static void xlnx_mix_layer_enable(struct xlnx_mix_hw *mixer,
+				  enum xlnx_mix_layer_id id)
+{
+	struct xlnx_mix_layer_data *layer_data;
+	u32 curr_state;
+	struct xlnx_mix *mix;
+
+	mix = container_of(mixer, struct xlnx_mix, mixer_hw);
+	if (mix->drm_primary_layer->mixer_layer->id == id) {
+		if (!xlnx_mixer_primary_enable)
+			return;
+	}
+
+	/* Ensure layer is marked as 'active' by application before
+	 * turning on in hardware.  In some cases, layer register data
+	 * may be written to otherwise inactive layers in lieu of, eventually,
+	 * turning them on.
+	 */
+	layer_data = xlnx_mix_get_layer_data(mixer, id);
+	if (!layer_data) {
+		DRM_ERROR("Invalid layer id %d\n", id);
+		return;
+	}
+	if (!layer_data->layer_regs.is_active)
+		return; /* for inactive layers silently return */
+
+	/* Check if request is to enable all layers or single layer */
+	if (id == mixer->max_layers) {
+		reg_writel(mixer->base, XVMIX_LAYERENABLE_DATA,
+			   mixer->enable_all_mask);
+
+	} else if ((id < mixer->layer_cnt) || ((id == mixer->logo_layer_id) &&
+		   mixer->logo_layer_en)) {
+		curr_state = reg_readl(mixer->base, XVMIX_LAYERENABLE_DATA);
+		if (id == mixer->logo_layer_id)
+			curr_state |= mixer->logo_en_mask;
+		else
+			curr_state |= BIT(id);
+		reg_writel(mixer->base, XVMIX_LAYERENABLE_DATA, curr_state);
+	} else {
+		DRM_ERROR("Can't enable requested layer %d\n", id);
+	}
+}
+
+/**
+ * xlnx_mix_disp_layer_enable - Enables video output represented by the
+ * plane object
+ * @plane: Drm plane object describing video layer to enable
+ *
+ */
+static void xlnx_mix_disp_layer_enable(struct xlnx_mix_plane *plane)
+{
+	struct xlnx_mix_hw *mixer_hw;
+	struct xlnx_mix_layer_data *l_data;
+	u32 id;
+
+	if (!plane)
+		return;
+	mixer_hw = to_mixer_hw(plane);
+	l_data = plane->mixer_layer;
+	id = l_data->id;
+	if (id > mixer_hw->logo_layer_id) {
+		DRM_DEBUG_KMS("Attempt to activate invalid layer: %d\n", id);
+		return;
+	}
+	if (id == XVMIX_LAYER_MASTER && !l_data->hw_config.is_streaming)
+		return;
+
+	xlnx_mix_layer_enable(mixer_hw, id);
+}
+
+/**
+ * xlnx_mix_layer_disable - Disables the requested layer
+ * @mixer:  Mixer for which the layer will be disabled
+ * @id: Logical id of the layer to be disabled (0-16)
+ *
+ * Disables the layer denoted by layer_id in the IP core.
+ * Layer 0 will indicate the background layer and layer 16 the logo
+ * layer. Passing the value of max layers will disable all
+ * layers.
+ */
+static void xlnx_mix_layer_disable(struct xlnx_mix_hw *mixer,
+				   enum xlnx_mix_layer_id id)
+{
+	u32 num_layers, curr_state;
+
+	num_layers = mixer->layer_cnt;
+
+	if (id == mixer->max_layers) {
+		reg_writel(mixer->base, XVMIX_LAYERENABLE_DATA,
+			   XVMIX_MASK_DISABLE_ALL_LAYERS);
+	} else if ((id < num_layers) ||
+		   ((id == mixer->logo_layer_id) && (mixer->logo_layer_en))) {
+		curr_state = reg_readl(mixer->base, XVMIX_LAYERENABLE_DATA);
+		if (id == mixer->logo_layer_id)
+			curr_state &= ~(mixer->logo_en_mask);
+		else
+			curr_state &= ~(BIT(id));
+		reg_writel(mixer->base, XVMIX_LAYERENABLE_DATA, curr_state);
+	} else {
+		DRM_ERROR("Can't disable requested layer %d\n", id);
+	}
+}
+
+/**
+ * xlnx_mix_disp_layer_disable - Disables video output represented by the
+ * plane object
+ * @plane: Drm plane object describing video layer to disable
+ *
+ */
+static void xlnx_mix_disp_layer_disable(struct xlnx_mix_plane *plane)
+{
+	struct xlnx_mix_hw *mixer_hw;
+	u32 layer_id;
+
+	if (plane)
+		mixer_hw = to_mixer_hw(plane);
+	else
+		return;
+	layer_id = plane->mixer_layer->id;
+	if (layer_id > mixer_hw->logo_layer_id)
+		return;
+
+	xlnx_mix_layer_disable(mixer_hw, layer_id);
+}
+
+static int xlnx_mix_mark_layer_inactive(struct xlnx_mix_plane *plane)
+{
+	if (!plane || !plane->mixer_layer)
+		return -ENODEV;
+
+	plane->mixer_layer->layer_regs.is_active = false;
+
+	return 0;
+}
+
+/* apply mode to plane pipe */
+static void xlnx_mix_plane_commit(struct drm_plane *base_plane)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+	struct dma_async_tx_descriptor *desc;
+	enum dma_ctrl_flags flags;
+	unsigned int i;
+
+	/* for xlnx video framebuffer dma, if used */
+	xilinx_xdma_drm_config(plane->dma[0].chan, plane->format);
+	for (i = 0; i < XVMIX_MAX_NUM_SUB_PLANES; i++) {
+		struct xlnx_mix_plane_dma *dma = &plane->dma[i];
+
+		if (dma->chan && dma->is_active) {
+			flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+			desc = dmaengine_prep_interleaved_dma(dma->chan,
+							      &dma->xt,
+							      flags);
+			if (!desc) {
+				DRM_ERROR("failed to prepare DMA descriptor\n");
+				return;
+			}
+			dmaengine_submit(desc);
+			dma_async_issue_pending(dma->chan);
+		}
+	}
+}
+
+static int xlnx_mix_plane_get_max_width(struct drm_plane *base_plane)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+
+	return plane->mixer->max_width;
+}
+
+static int xlnx_mix_plane_get_max_height(struct drm_plane *base_plane)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+
+	return plane->mixer->max_height;
+}
+
+static int xlnx_mix_plane_get_max_cursor_width(struct drm_plane *base_plane)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+
+	return plane->mixer->max_cursor_width;
+}
+
+static int xlnx_mix_plane_get_max_cursor_height(struct drm_plane *base_plane)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+
+	return plane->mixer->max_cursor_height;
+}
+
+static int xlnx_mix_crtc_get_max_width(struct xlnx_crtc *crtc)
+{
+	return xlnx_mix_plane_get_max_width(crtc->crtc.primary);
+}
+
+static int xlnx_mix_crtc_get_max_height(struct xlnx_crtc *crtc)
+{
+	return xlnx_mix_plane_get_max_height(crtc->crtc.primary);
+}
+
+static unsigned int xlnx_mix_crtc_get_max_cursor_width(struct xlnx_crtc *crtc)
+{
+	return xlnx_mix_plane_get_max_cursor_width(crtc->crtc.primary);
+}
+
+static unsigned int xlnx_mix_crtc_get_max_cursor_height(struct xlnx_crtc *crtc)
+{
+	return xlnx_mix_plane_get_max_cursor_height(crtc->crtc.primary);
+}
+
+/**
+ * xlnx_mix_crtc_get_format - Get the current device format
+ * @crtc: xlnx crtc object
+ *
+ * Get the current format of pipeline
+ *
+ * Return: the corresponding DRM_FORMAT_XXX
+ */
+static uint32_t xlnx_mix_crtc_get_format(struct xlnx_crtc *crtc)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(crtc->crtc.primary);
+
+	return plane->format;
+}
+
+/**
+ * xlnx_mix_crtc_get_align - Get the alignment value for pitch
+ * @crtc: xlnx crtc object
+ *
+ * Get the alignment value for pitch from the plane
+ *
+ * Return: The alignment value if successful, or the error code.
+ */
+static unsigned int xlnx_mix_crtc_get_align(struct xlnx_crtc *crtc)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(crtc->crtc.primary);
+	struct xlnx_mix *m = plane->mixer;
+
+	return XVMIX_BASE_ALIGN * m->mixer_hw.ppc;
+}
+
+/**
+ * xlnx_mix_attach_plane_prop - Attach mixer-specific drm property to
+ * the given plane
+ * @plane: Xilinx drm plane object to inspect and attach appropriate
+ *  properties to
+ *
+ * The linked mixer layer will be inspected to see what capabilities it offers
+ * (e.g. global layer alpha; scaling) and drm property objects that indicate
+ * those capabilities will then be attached and initialized to default values.
+ */
+static void xlnx_mix_attach_plane_prop(struct xlnx_mix_plane *plane)
+{
+	struct drm_mode_object *base = &plane->base.base;
+	struct xlnx_mix *mixer = plane->mixer;
+
+	if (plane->mixer_layer->hw_config.can_scale)
+		drm_object_attach_property(base, mixer->scale_prop,
+					   XVMIX_SCALE_FACTOR_1X);
+	if (plane->mixer_layer->hw_config.can_alpha)
+		drm_object_attach_property(base, mixer->alpha_prop,
+					   XVMIX_ALPHA_MAX);
+	if (mixer->mixer_hw.csc_enabled) {
+		u32 supported_encodings = BIT(DRM_COLOR_YCBCR_BT601) |
+					  BIT(DRM_COLOR_YCBCR_BT709) |
+					  BIT(DRM_COLOR_YCBCR_BT2020);
+		u32 supported_ranges = BIT(DRM_COLOR_YCBCR_LIMITED_RANGE) |
+				       BIT(DRM_COLOR_YCBCR_FULL_RANGE);
+		enum drm_color_encoding encoding = DRM_COLOR_YCBCR_BT709;
+		enum drm_color_range range = DRM_COLOR_YCBCR_LIMITED_RANGE;
+
+		drm_plane_create_color_properties(&plane->base,
+						  supported_encodings,
+						  supported_ranges,
+						  encoding, range);
+	}
+}
+
+static int xlnx_mix_mark_layer_active(struct xlnx_mix_plane *plane)
+{
+	if (!plane->mixer_layer)
+		return -ENODEV;
+	plane->mixer_layer->layer_regs.is_active = true;
+
+	return 0;
+}
+
+static bool xlnx_mix_isfmt_support(u32 format)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(color_table); i++) {
+		if (format == color_table[i])
+			return true;
+	}
+	return false;
+}
+
+/*************** DISPLAY ************/
+
+/**
+ * xlnx_mix_get_layer_scaling - Get layer scaling factor
+ * @mixer: Mixer instance to program with new background color
+ * @id: Plane id
+ *
+ * Applicable only for overlay layers
+ *
+ * Return:
+ * scaling factor of the specified layer
+ */
+static int xlnx_mix_get_layer_scaling(struct xlnx_mix_hw *mixer,
+				      enum xlnx_mix_layer_id id)
+{
+	int scale_factor = 0;
+	u32 reg;
+	struct xlnx_mix_layer_data *l_data = xlnx_mix_get_layer_data(mixer, id);
+
+	if (id == mixer->logo_layer_id) {
+		if (mixer->logo_layer_en) {
+			if (mixer->max_layers > XVMIX_MAX_OVERLAY_LAYERS)
+				reg = XVMIX_LOGOSCALEFACTOR_DATA +
+					XVMIX_LOGO_OFFSET;
+			else
+				reg = XVMIX_LOGOSCALEFACTOR_DATA;
+			scale_factor = reg_readl(mixer->base, reg);
+			l_data->layer_regs.scale_fact = scale_factor;
+		}
+	} else {
+		/*Layer0-Layer15*/
+		if (id < mixer->logo_layer_id && l_data->hw_config.can_scale) {
+			reg = XVMIX_LAYERSCALE_0_DATA + (id * XVMIX_REG_OFFSET);
+			scale_factor = reg_readl(mixer->base, reg);
+			l_data->layer_regs.scale_fact = scale_factor;
+		}
+	}
+	return scale_factor;
+}
+
+/**
+ * xlnx_mix_set_layer_window - Sets the position of an overlay layer
+ * @mixer: Specific mixer object instance controlling the video
+ * @id: Logical layer id (1-15) to be positioned
+ * @x_pos: new: Column to start display of overlay layer
+ * @y_pos: new: Row to start display of overlay layer
+ * @width: Number of active columns to dislay for overlay layer
+ * @height: Number of active columns to display for overlay layer
+ * @stride: Width in bytes of overaly memory buffer (memory layer only)
+ *
+ * Sets the position of an overlay layer over the background layer (layer 0)
+ * Applicable only for layers 1-15 or the logo layer
+ *
+ * Return:
+ * Zero on success, -EINVAL if position is invalid or -ENODEV if layer
+ */
+static int xlnx_mix_set_layer_window(struct xlnx_mix_hw *mixer,
+				     enum xlnx_mix_layer_id id, u32 x_pos,
+				     u32 y_pos, u32 width, u32 height,
+				     u32 stride)
+{
+	struct xlnx_mix_layer_data *l_data;
+	u32 scale = 0;
+	int status = -EINVAL;
+	u32 x_reg, y_reg, w_reg, h_reg, s_reg;
+	u32 off;
+
+	l_data = xlnx_mix_get_layer_data(mixer, id);
+	if (!l_data)
+		return status;
+
+	scale = xlnx_mix_get_layer_scaling(mixer, id);
+	if (!is_window_valid(mixer, x_pos, y_pos, width, height, scale))
+		return status;
+
+	if (id == mixer->logo_layer_id) {
+		if (!(mixer->logo_layer_en &&
+		      width <= l_data->hw_config.max_width &&
+		      height <= l_data->hw_config.max_height &&
+		      height >= l_data->hw_config.min_height &&
+		      width >= l_data->hw_config.min_width))
+			return status;
+
+		if (mixer->max_layers > XVMIX_MAX_OVERLAY_LAYERS) {
+			x_reg = XVMIX_LOGOSTARTX_DATA + XVMIX_LOGO_OFFSET;
+			y_reg = XVMIX_LOGOSTARTY_DATA + XVMIX_LOGO_OFFSET;
+			w_reg = XVMIX_LOGOWIDTH_DATA + XVMIX_LOGO_OFFSET;
+			h_reg = XVMIX_LOGOHEIGHT_DATA + XVMIX_LOGO_OFFSET;
+		} else {
+			x_reg = XVMIX_LOGOSTARTX_DATA;
+			y_reg = XVMIX_LOGOSTARTY_DATA;
+			w_reg = XVMIX_LOGOWIDTH_DATA;
+			h_reg = XVMIX_LOGOHEIGHT_DATA;
+		}
+		reg_writel(mixer->base, x_reg, x_pos);
+		reg_writel(mixer->base, y_reg, y_pos);
+		reg_writel(mixer->base, w_reg, width);
+		reg_writel(mixer->base, h_reg, height);
+		l_data->layer_regs.x_pos = x_pos;
+		l_data->layer_regs.y_pos = y_pos;
+		l_data->layer_regs.width = width;
+		l_data->layer_regs.height = height;
+		status = 0;
+	} else {
+		 /*Layer1-Layer15*/
+
+		if (!(id < mixer->layer_cnt &&
+		      width <= l_data->hw_config.max_width &&
+		      width >= l_data->hw_config.min_width))
+			return status;
+		x_reg = XVMIX_LAYERSTARTX_0_DATA;
+		y_reg = XVMIX_LAYERSTARTY_0_DATA;
+		w_reg = XVMIX_LAYERWIDTH_0_DATA;
+		h_reg = XVMIX_LAYERHEIGHT_0_DATA;
+		s_reg = XVMIX_LAYERSTRIDE_0_DATA;
+
+		off = id * XVMIX_REG_OFFSET;
+		reg_writel(mixer->base, (x_reg + off), x_pos);
+		reg_writel(mixer->base, (y_reg + off), y_pos);
+		reg_writel(mixer->base, (w_reg + off), width);
+		reg_writel(mixer->base, (h_reg + off), height);
+		l_data->layer_regs.x_pos = x_pos;
+		l_data->layer_regs.y_pos = y_pos;
+		l_data->layer_regs.width = width;
+		l_data->layer_regs.height = height;
+
+		if (!l_data->hw_config.is_streaming)
+			reg_writel(mixer->base, (s_reg + off), stride);
+		status = 0;
+	}
+	return status;
+}
+
+/**
+ * xlnx_mix_set_layer_dimensions - Set layer dimensions
+ * @plane: Drm plane object desribing video layer to reposition
+ * @crtc_x: New horizontal anchor postion from which to begin rendering
+ * @crtc_y: New vertical anchor position from which to begin rendering
+ * @width: Width, in pixels, to render from stream or memory buffer
+ * @height: Height, in pixels, to render from stream or memory buffer
+ * @stride: Width, in bytes, of a memory buffer.  Used only for
+ *  memory layers.  Use 0 for streaming layers.
+ *
+ * Establishes new coordinates and dimensions for a video plane layer
+ * New size and coordinates of window must fit within the currently active
+ * area of the crtc (e.g. the background resolution)
+ *
+ * Return: 0 if successful; Either -EINVAL if coordindate data is invalid
+ * or -ENODEV if layer data not present
+ */
+static int xlnx_mix_set_layer_dimensions(struct xlnx_mix_plane *plane,
+					 u32 crtc_x, u32 crtc_y,
+					  u32 width, u32 height, u32 stride)
+{
+	struct xlnx_mix *mixer = plane->mixer;
+	struct xlnx_mix_hw *mixer_hw = to_mixer_hw(plane);
+	struct xlnx_mix_layer_data *layer_data;
+	enum xlnx_mix_layer_id layer_id;
+	int ret = 0;
+
+	layer_data = plane->mixer_layer;
+	layer_id = layer_data->id;
+	if (layer_data->layer_regs.height != height ||
+	    layer_data->layer_regs.width != width) {
+		if (mixer->drm_primary_layer == plane)
+			xlnx_mix_layer_disable(mixer_hw, XVMIX_LAYER_MASTER);
+
+		xlnx_mix_layer_disable(mixer_hw, layer_id);
+	}
+	if (mixer->drm_primary_layer == plane) {
+		crtc_x = 0;
+		crtc_y = 0;
+		ret = xlnx_mix_set_active_area(mixer_hw, width, height);
+		if (ret)
+			return ret;
+		xlnx_mix_layer_enable(mixer_hw, XVMIX_LAYER_MASTER);
+	}
+	if (layer_id != XVMIX_LAYER_MASTER && layer_id < mixer_hw->max_layers) {
+		ret = xlnx_mix_set_layer_window(mixer_hw, layer_id, crtc_x,
+						crtc_y, width, height, stride);
+		if (ret)
+			return ret;
+		xlnx_mix_disp_layer_enable(plane);
+	}
+	return ret;
+}
+
+/**
+ * xlnx_mix_set_layer_scaling - Sets scaling factor
+ * @mixer: Instance of mixer to be subject of scaling request
+ * @id: Logical id of video layer subject to new scale setting
+ * @scale: scale Factor (1x, 2x or 4x) for horiz. and vert. dimensions
+ *
+ * Sets the scaling factor for the specified video layer
+ * Not applicable to background stream layer (layer 0)
+ *
+ * Return:
+ * Zero on success, -EINVAL on failure to set scale for layer (likely
+ * returned if resulting size of layer exceeds dimensions of active
+ * display area
+ */
+static int xlnx_mix_set_layer_scaling(struct xlnx_mix_hw *mixer,
+				      enum xlnx_mix_layer_id id, u32 scale)
+{
+	void __iomem *reg = mixer->base;
+	struct xlnx_mix_layer_data *l_data;
+	int status = 0;
+	u32 x_pos, y_pos, width, height, offset;
+
+	l_data = xlnx_mix_get_layer_data(mixer, id);
+	x_pos = l_data->layer_regs.x_pos;
+	y_pos = l_data->layer_regs.y_pos;
+	width  = l_data->layer_regs.width;
+	height = l_data->layer_regs.height;
+
+	if (!is_window_valid(mixer, x_pos, y_pos, width, height, scale))
+		return -EINVAL;
+
+	if (id == mixer->logo_layer_id) {
+		if (mixer->logo_layer_en) {
+			if (mixer->max_layers > XVMIX_MAX_OVERLAY_LAYERS)
+				reg_writel(reg, XVMIX_LOGOSCALEFACTOR_DATA +
+					   XVMIX_LOGO_OFFSET, scale);
+			else
+				reg_writel(reg, XVMIX_LOGOSCALEFACTOR_DATA,
+					   scale);
+			l_data->layer_regs.scale_fact = scale;
+			status = 0;
+		}
+	} else {
+		 /* Layer0-Layer15 */
+		if (id < mixer->layer_cnt && l_data->hw_config.can_scale) {
+			offset = id * XVMIX_REG_OFFSET;
+
+			reg_writel(reg, (XVMIX_LAYERSCALE_0_DATA + offset),
+				   scale);
+			l_data->layer_regs.scale_fact = scale;
+			status = 0;
+		}
+	}
+	return status;
+}
+
+/**
+ * xlnx_mix_set_layer_scale - Change video scale factor for video plane
+ * @plane: Drm plane object describing layer to be modified
+ * @val: Index of scale factor to use:
+ *		0 = 1x
+ *		1 = 2x
+ *		2 = 4x
+ *
+ * Return:
+ * Zero on success, either -EINVAL if scale value is illegal or
+ * -ENODEV if layer does not exist (null)
+ */
+static int xlnx_mix_set_layer_scale(struct xlnx_mix_plane *plane,
+				    uint64_t val)
+{
+	struct xlnx_mix_hw *mixer_hw = to_mixer_hw(plane);
+	struct xlnx_mix_layer_data *layer = plane->mixer_layer;
+	int ret;
+
+	if (!layer || !layer->hw_config.can_scale)
+		return -ENODEV;
+	if (val > XVMIX_SCALE_FACTOR_4X) {
+		DRM_ERROR("Mixer layer scale value illegal.\n");
+		return -EINVAL;
+	}
+	xlnx_mix_disp_layer_disable(plane);
+	msleep(50);
+	ret = xlnx_mix_set_layer_scaling(mixer_hw, layer->id, val);
+	xlnx_mix_disp_layer_enable(plane);
+
+	return ret;
+}
+
+/**
+ * xlnx_mix_set_layer_alpha - Set the alpha value
+ * @mixer: Instance of mixer controlling layer to modify
+ * @layer_id: Logical id of video overlay to adjust alpha setting
+ * @alpha: Desired alpha setting (0-255) for layer specified
+ *            255 = completely opaque
+ *            0 = fully transparent
+ *
+ * Set the layer global transparency for a video overlay
+ * Not applicable to background streaming layer
+ *
+ * Return:
+ * Zero on success, -EINVAL on failure
+ */
+static int xlnx_mix_set_layer_alpha(struct xlnx_mix_hw *mixer,
+				    enum xlnx_mix_layer_id layer_id, u32 alpha)
+{
+	struct xlnx_mix_layer_data *layer_data;
+	u32 reg;
+	int status = -EINVAL;
+
+	layer_data = xlnx_mix_get_layer_data(mixer, layer_id);
+
+	if (layer_id == mixer->logo_layer_id) {
+		if (mixer->logo_layer_en) {
+			if (mixer->max_layers > XVMIX_MAX_OVERLAY_LAYERS)
+				reg = XVMIX_LOGOALPHA_DATA + XVMIX_LOGO_OFFSET;
+			else
+				reg = XVMIX_LOGOALPHA_DATA;
+			reg_writel(mixer->base, reg, alpha);
+			layer_data->layer_regs.alpha = alpha;
+			status = 0;
+		}
+	} else {
+		 /*Layer1-Layer15*/
+		if (layer_id < mixer->layer_cnt &&
+		    layer_data->hw_config.can_alpha) {
+			u32 offset =  layer_id * XVMIX_REG_OFFSET;
+
+			reg = XVMIX_LAYERALPHA_0_DATA;
+			reg_writel(mixer->base, (reg + offset), alpha);
+			layer_data->layer_regs.alpha = alpha;
+			status = 0;
+		}
+	}
+	return status;
+}
+
+/**
+ * xlnx_mix_disp_set_layer_alpha - Change the transparency of an entire plane
+ * @plane: Video layer affected by new alpha setting
+ * @val: Value of transparency setting (0-255) with 255 being opaque
+ *  0 being fully transparent
+ *
+ * Return:
+ * Zero on success, -EINVAL on failure
+ */
+static int xlnx_mix_disp_set_layer_alpha(struct xlnx_mix_plane *plane,
+					 uint64_t val)
+{
+	struct xlnx_mix_hw *mixer_hw = to_mixer_hw(plane);
+	struct xlnx_mix_layer_data *layer = plane->mixer_layer;
+
+	if (!layer || !layer->hw_config.can_alpha)
+		return -ENODEV;
+	if (val > XVMIX_ALPHA_MAX) {
+		DRM_ERROR("Mixer layer alpha dts value illegal.\n");
+		return -EINVAL;
+	}
+	return xlnx_mix_set_layer_alpha(mixer_hw, layer->id, val);
+}
+
+/**
+ * xlnx_mix_set_layer_buff_addr - Set buff addr for layer
+ * @mixer: Instance of mixer controlling layer to modify
+ * @id: Logical id of video overlay to adjust alpha setting
+ * @luma_addr: Start address of plane 1 of frame buffer for layer 1
+ * @chroma_addr: Start address of plane 2 of frame buffer for layer 1
+ *
+ * Sets the buffer address of the specified layer
+ * Return:
+ * Zero on success, -EINVAL on failure
+ */
+static int xlnx_mix_set_layer_buff_addr(struct xlnx_mix_hw *mixer,
+					enum xlnx_mix_layer_id id,
+					dma_addr_t luma_addr,
+					dma_addr_t chroma_addr)
+{
+	struct xlnx_mix_layer_data *layer_data;
+	u32 align, offset;
+	u32 reg1, reg2;
+
+	if (id >= mixer->layer_cnt)
+		return -EINVAL;
+
+	/* Check if addr is aligned to aximm width (PPC * 64-bits) */
+	align = mixer->ppc * 8;
+	if ((luma_addr % align) != 0 || (chroma_addr % align) != 0)
+		return -EINVAL;
+
+	offset = (id - 1) * XVMIX_REG_OFFSET;
+	reg1 = XVMIX_LAYER1_BUF1_V_DATA + offset;
+	reg2 = XVMIX_LAYER1_BUF2_V_DATA + offset;
+	layer_data = &mixer->layer_data[id];
+	if (mixer->dma_addr_size == 64 && sizeof(dma_addr_t) == 8) {
+		reg_writeq(mixer->base, reg1, luma_addr);
+		reg_writeq(mixer->base, reg2, chroma_addr);
+	} else {
+		reg_writel(mixer->base, reg1, (u32)luma_addr);
+		reg_writel(mixer->base, reg2, (u32)chroma_addr);
+	}
+	layer_data->layer_regs.buff_addr1 = luma_addr;
+	layer_data->layer_regs.buff_addr2 = chroma_addr;
+
+	return 0;
+}
+
+/**
+ * xlnx_mix_hw_plane_dpms - Implementation of display power management
+ * system call (dpms).
+ * @plane: Plane/mixer layer to enable/disable (based on dpms value)
+ * @dpms: Display power management state to act upon
+ *
+ * Designed to disable and turn off a plane and restore all attached drm
+ * properities to their initial values.  Alterntively, if dpms is "on", will
+ * enable a layer.
+ */
+
+static void
+xlnx_mix_hw_plane_dpms(struct xlnx_mix_plane *plane, int dpms)
+{
+	struct xlnx_mix *mixer;
+
+	if (!plane->mixer)
+		return;
+	mixer = plane->mixer;
+	plane->dpms = dpms;
+
+	switch (dpms) {
+	case DRM_MODE_DPMS_ON:
+		xlnx_mix_disp_layer_enable(plane);
+		break;
+	default:
+		xlnx_mix_mark_layer_inactive(plane);
+		xlnx_mix_disp_layer_disable(plane);
+		/* restore to default property values */
+		if (mixer->alpha_prop)
+			xlnx_mix_disp_set_layer_alpha(plane, XVMIX_ALPHA_MAX);
+		if (mixer->scale_prop)
+			xlnx_mix_set_layer_scale(plane, XVMIX_SCALE_FACTOR_1X);
+	}
+}
+
+static void xlnx_mix_plane_dpms(struct drm_plane *base_plane, int dpms)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+	unsigned int i;
+
+	DRM_DEBUG_KMS("plane->id: %d\n", plane->id);
+	DRM_DEBUG_KMS("dpms: %d -> %d\n", plane->dpms, dpms);
+
+	if (plane->dpms == dpms)
+		return;
+	plane->dpms = dpms;
+	switch (dpms) {
+	case DRM_MODE_DPMS_ON:
+		/* start dma engine */
+		for (i = 0; i < XVMIX_MAX_NUM_SUB_PLANES; i++)
+			if (plane->dma[i].chan && plane->dma[i].is_active)
+				dma_async_issue_pending(plane->dma[i].chan);
+		xlnx_mix_hw_plane_dpms(plane, dpms);
+		break;
+	default:
+		xlnx_mix_hw_plane_dpms(plane, dpms);
+		/* stop dma engine and release descriptors */
+		for (i = 0; i < XVMIX_MAX_NUM_SUB_PLANES; i++) {
+			if (plane->dma[i].chan && plane->dma[i].is_active) {
+				dmaengine_terminate_sync(plane->dma[i].chan);
+				plane->dma[i].is_active = false;
+			}
+		}
+		break;
+	}
+}
+
+static int
+xlnx_mix_disp_plane_atomic_set_property(struct drm_plane *base_plane,
+					struct drm_plane_state *state,
+				      struct drm_property *property, u64 val)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+	struct xlnx_mix *mixer = plane->mixer;
+
+	if (property == mixer->alpha_prop)
+		return xlnx_mix_disp_set_layer_alpha(plane, val);
+	else if (property == mixer->scale_prop)
+		return xlnx_mix_set_layer_scale(plane, val);
+	else
+		return -EINVAL;
+	return 0;
+}
+
+static int
+xlnx_mix_disp_plane_atomic_get_property(struct drm_plane *base_plane,
+					const struct drm_plane_state *state,
+				      struct drm_property *property,
+				      uint64_t *val)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+	struct xlnx_mix *mixer = plane->mixer;
+	struct xlnx_mix_hw *mixer_hw = to_mixer_hw(plane);
+	u32 layer_id = plane->mixer_layer->id;
+
+	if (property == mixer->alpha_prop)
+		*val = mixer_hw->layer_data[layer_id].layer_regs.alpha;
+	else if (property == mixer->scale_prop)
+		*val = mixer_hw->layer_data[layer_id].layer_regs.scale_fact;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * xlnx_mix_disp_plane_atomic_update_plane - plane update using atomic
+ * @plane: plane object to update
+ * @crtc: owning CRTC of owning plane
+ * @fb: framebuffer to flip onto plane
+ * @crtc_x: x offset of primary plane on crtc
+ * @crtc_y: y offset of primary plane on crtc
+ * @crtc_w: width of primary plane rectangle on crtc
+ * @crtc_h: height of primary plane rectangle on crtc
+ * @src_x: x offset of @fb for panning
+ * @src_y: y offset of @fb for panning
+ * @src_w: width of source rectangle in @fb
+ * @src_h: height of source rectangle in @fb
+ * @ctx: lock acquire context
+ *
+ * Provides a default plane update handler using the atomic driver interface.
+ *
+ * RETURNS:
+ * Zero on success, error code on failure
+ */
+static int
+xlnx_mix_disp_plane_atomic_update_plane(struct drm_plane *plane,
+					struct drm_crtc *crtc,
+					struct drm_framebuffer *fb,
+					int crtc_x, int crtc_y,
+					unsigned int crtc_w,
+					unsigned int crtc_h,
+					uint32_t src_x, uint32_t src_y,
+					uint32_t src_w, uint32_t src_h,
+					struct drm_modeset_acquire_ctx *ctx)
+{
+	struct drm_atomic_state *state;
+	struct drm_plane_state *plane_state;
+	int ret = 0;
+
+	state = drm_atomic_state_alloc(plane->dev);
+	if (!state)
+		return -ENOMEM;
+
+	state->acquire_ctx = ctx;
+	plane_state = drm_atomic_get_plane_state(state, plane);
+	if (IS_ERR(plane_state)) {
+		ret = PTR_ERR(plane_state);
+		goto fail;
+	}
+
+	ret = drm_atomic_set_crtc_for_plane(plane_state, crtc);
+	if (ret != 0)
+		goto fail;
+
+	drm_atomic_set_fb_for_plane(plane_state, fb);
+	plane_state->crtc_x = crtc_x;
+	plane_state->crtc_y = crtc_y;
+	plane_state->crtc_w = crtc_w;
+	plane_state->crtc_h = crtc_h;
+	plane_state->src_x = src_x;
+	plane_state->src_y = src_y;
+	plane_state->src_w = src_w;
+	plane_state->src_h = src_h;
+
+	if (plane == crtc->cursor)
+		state->legacy_cursor_update = true;
+
+	/* Do async-update if possible */
+	state->async_update = !drm_atomic_helper_async_check(plane->dev, state);
+
+	ret = drm_atomic_commit(state);
+
+fail:
+	drm_atomic_state_put(state);
+	return ret;
+}
+
+static struct drm_plane_funcs xlnx_mix_plane_funcs = {
+	.update_plane	= xlnx_mix_disp_plane_atomic_update_plane,
+	.disable_plane	= drm_atomic_helper_disable_plane,
+	.atomic_set_property	= xlnx_mix_disp_plane_atomic_set_property,
+	.atomic_get_property	= xlnx_mix_disp_plane_atomic_get_property,
+	.destroy		= drm_plane_cleanup,
+	.reset			= drm_atomic_helper_plane_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_plane_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_plane_destroy_state,
+};
+
+/**
+ * xlnx_mix_logo_load - Loads mixer's internal bram
+ * @mixer: Mixer instance to act upon
+ * @logo_w: Width of logo in pixels
+ * @logo_h: Height of logo in pixels
+ * @r_buf: Pointer to byte buffer array of R data values
+ * @g_buf: Pointer to byte buffer array of G data values
+ * @b_buf: Pointer to byte buffer array of B data values
+ * @a_buf: Pointer to byte buffer array of A data values
+ *
+ * Loads mixer's internal bram with planar R, G, B and A data
+ *
+ * Return:
+ * Zero on success, -ENODEV if logo layer not enabled; -EINVAL otherwise
+ */
+static int xlnx_mix_logo_load(struct xlnx_mix_hw *mixer, u32 logo_w, u32 logo_h,
+			      u8 *r_buf, u8 *g_buf, u8 *b_buf, u8 *a_buf)
+{
+	void __iomem *reg = mixer->base;
+	struct xlnx_mix_layer_data *layer_data;
+
+	int x;
+	u32 shift;
+	u32 rword, gword, bword, aword;
+	u32 pixel_cnt = logo_w * logo_h;
+	u32 unaligned_pix_cnt = pixel_cnt % 4;
+	u32 curr_x_pos, curr_y_pos;
+	u32 rbase_addr, gbase_addr, bbase_addr, abase_addr;
+
+	layer_data = xlnx_mix_get_layer_data(mixer, mixer->logo_layer_id);
+	rword = 0;
+	gword = 0;
+	bword = 0;
+	aword = 0;
+
+	if (!layer_data)
+		return -ENODEV;
+
+	/* RGBA data should be 32-bit word aligned */
+	if (unaligned_pix_cnt && mixer->logo_pixel_alpha_enabled)
+		return -EINVAL;
+
+	if (!(mixer->logo_layer_en &&
+	      logo_w <= layer_data->hw_config.max_width &&
+	    logo_h <= layer_data->hw_config.max_height))
+		return -EINVAL;
+
+	rbase_addr = XVMIX_LOGOR_V_BASE;
+	gbase_addr = XVMIX_LOGOG_V_BASE;
+	bbase_addr = XVMIX_LOGOB_V_BASE;
+	abase_addr = XVMIX_LOGOA_V_BASE;
+
+	for (x = 0; x < pixel_cnt; x++) {
+		shift = (x % 4) * 8;
+		rword |= r_buf[x] << shift;
+		gword |= g_buf[x] << shift;
+		bword |= b_buf[x] << shift;
+		if (mixer->logo_pixel_alpha_enabled)
+			aword |= a_buf[x] << shift;
+
+		if (x % 4 == 3) {
+			reg_writel(reg, (rbase_addr + (x - 3)), rword);
+			reg_writel(reg, (gbase_addr + (x - 3)), gword);
+			reg_writel(reg, (bbase_addr + (x - 3)), bword);
+			if (mixer->logo_pixel_alpha_enabled)
+				reg_writel(reg, (abase_addr + (x - 3)), aword);
+		}
+	}
+
+	curr_x_pos = layer_data->layer_regs.x_pos;
+	curr_y_pos = layer_data->layer_regs.y_pos;
+	return xlnx_mix_set_layer_window(mixer, mixer->logo_layer_id,
+					 curr_x_pos, curr_y_pos,
+					 logo_w, logo_h, 0);
+}
+
+static int xlnx_mix_update_logo_img(struct xlnx_mix_plane *plane,
+				    struct drm_gem_cma_object *buffer,
+				     u32 src_w, u32 src_h)
+{
+	struct xlnx_mix_layer_data *logo_layer = plane->mixer_layer;
+	struct xlnx_mix_hw *mixer = to_mixer_hw(plane);
+	size_t pixel_cnt = src_h * src_w;
+	bool per_pixel_alpha = false;
+	u32 max_width = logo_layer->hw_config.max_width;
+	u32 max_height = logo_layer->hw_config.max_height;
+	u32 min_width = logo_layer->hw_config.min_width;
+	u32 min_height = logo_layer->hw_config.min_height;
+	u8 *r_data = NULL;
+	u8 *g_data = NULL;
+	u8 *b_data = NULL;
+	u8 *a_data = NULL;
+	size_t el_size = sizeof(u8);
+	u8 *pixel_mem_data;
+	int ret, i, j;
+
+	/* ensure valid conditions for update */
+	if (logo_layer->id != mixer->logo_layer_id)
+		return 0;
+
+	if (src_h > max_height || src_w > max_width ||
+	    src_h < min_height || src_w < min_width) {
+		DRM_ERROR("Mixer logo/cursor layer dimensions illegal.\n");
+		return -EINVAL;
+	}
+
+	if (!xlnx_mix_isfmt_support(plane->mixer_layer->hw_config.vid_fmt)) {
+		DRM_ERROR("DRM color format not supported for logo layer\n");
+		return -EINVAL;
+	}
+	per_pixel_alpha = (logo_layer->hw_config.vid_fmt ==
+			   DRM_FORMAT_RGBA8888) ? true : false;
+	r_data = kcalloc(pixel_cnt, el_size, GFP_KERNEL);
+	g_data = kcalloc(pixel_cnt, el_size, GFP_KERNEL);
+	b_data = kcalloc(pixel_cnt, el_size, GFP_KERNEL);
+	if (per_pixel_alpha)
+		a_data = kcalloc(pixel_cnt, el_size, GFP_KERNEL);
+
+	if (!r_data || !g_data || !b_data || (per_pixel_alpha && !a_data)) {
+		DRM_ERROR("Unable to allocate memory for logo layer data\n");
+		ret = -ENOMEM;
+		goto free;
+	}
+	/* ensure buffer attributes have changed to indicate new logo
+	 * has been created
+	 */
+	if ((phys_addr_t)buffer->vaddr == logo_layer->layer_regs.buff_addr1 &&
+	    src_w == logo_layer->layer_regs.width &&
+	    src_h == logo_layer->layer_regs.height)
+		return 0;
+
+	/* cache buffer address for future comparison */
+	logo_layer->layer_regs.buff_addr1 = (phys_addr_t)buffer->vaddr;
+	pixel_mem_data = (u8 *)(buffer->vaddr);
+	for (i = 0, j = 0; j < pixel_cnt; j++) {
+		if (per_pixel_alpha && a_data)
+			a_data[j] = pixel_mem_data[i++];
+
+		b_data[j] = pixel_mem_data[i++];
+		g_data[j] = pixel_mem_data[i++];
+		r_data[j] = pixel_mem_data[i++];
+	}
+	ret = xlnx_mix_logo_load(to_mixer_hw(plane), src_w, src_h, r_data,
+				 g_data, b_data,
+				 per_pixel_alpha ? a_data : NULL);
+free:
+	kfree(r_data);
+	kfree(g_data);
+	kfree(b_data);
+	kfree(a_data);
+
+	return ret;
+}
+
+/**
+ * xlnx_mix_set_plane - Implementation of DRM plane_update callback
+ * @plane: xlnx_mix_plane object containing references to
+ *  the base plane and mixer
+ * @fb: Framebuffer descriptor
+ * @crtc_x: X position of layer on crtc.  Note, if the plane represents either
+ *  the master hardware layer (video0) or the layer representing the DRM primary
+ *  layer, the crtc x/y coordinates are either ignored and/or set to 0/0
+ *  respectively.
+ * @crtc_y: Y position of layer.  See description of crtc_x handling
+ * for more inforation.
+ * @src_x: x-offset in memory buffer from which to start reading
+ * @src_y: y-offset in memory buffer from which to start reading
+ * @src_w: Number of horizontal pixels to read from memory per row
+ * @src_h: Number of rows of video data to read from memory
+ *
+ * Configures a mixer layer to comply with user space SET_PLANE icotl
+ * call.
+ *
+ * Return:
+ * Zero on success, non-zero linux error code otherwise.
+ */
+static int xlnx_mix_set_plane(struct xlnx_mix_plane *plane,
+			      struct drm_framebuffer *fb,
+			      int crtc_x, int crtc_y,
+			      u32 src_x, u32 src_y,
+			      u32 src_w, u32 src_h)
+{
+	struct xlnx_mix_hw *mixer_hw;
+	struct xlnx_mix *mixer;
+	struct drm_gem_cma_object *luma_buffer;
+	u32 luma_stride = fb->pitches[0];
+	dma_addr_t luma_addr, chroma_addr = 0;
+	u32 active_area_width;
+	u32 active_area_height;
+	enum xlnx_mix_layer_id layer_id;
+	int ret;
+	const struct drm_format_info *info = fb->format;
+
+	mixer = plane->mixer;
+	mixer_hw = &mixer->mixer_hw;
+	layer_id = plane->mixer_layer->id;
+	active_area_width =
+		mixer->drm_primary_layer->mixer_layer->layer_regs.width;
+	active_area_height =
+		mixer->drm_primary_layer->mixer_layer->layer_regs.height;
+	/* compute memory data */
+	luma_buffer = drm_fb_cma_get_gem_obj(fb, 0);
+	luma_addr = drm_fb_cma_get_gem_addr(fb, plane->base.state, 0);
+	if (!luma_addr) {
+		DRM_ERROR("%s failed to get luma paddr\n", __func__);
+		return -EINVAL;
+	}
+
+	if (info->num_planes > 1) {
+		chroma_addr = drm_fb_cma_get_gem_addr(fb, plane->base.state, 1);
+		if (!chroma_addr) {
+			DRM_ERROR("failed to get chroma paddr\n");
+			return -EINVAL;
+		}
+	}
+	ret = xlnx_mix_mark_layer_active(plane);
+	if (ret)
+		return ret;
+
+	switch (layer_id) {
+	case XVMIX_LAYER_MASTER:
+		if (!plane->mixer_layer->hw_config.is_streaming)
+			xlnx_mix_mark_layer_inactive(plane);
+		if (mixer->drm_primary_layer == mixer->hw_master_layer) {
+			xlnx_mix_layer_disable(mixer_hw, layer_id);
+			ret = xlnx_mix_set_active_area(mixer_hw, src_w, src_h);
+			if (ret)
+				return ret;
+			xlnx_mix_layer_enable(mixer_hw, layer_id);
+
+		} else if (src_w != active_area_width ||
+			   src_h != active_area_height) {
+			DRM_ERROR("Invalid dimensions for mixer layer 0.\n");
+			return -EINVAL;
+		}
+		break;
+
+	default:
+		ret = xlnx_mix_set_layer_dimensions(plane, crtc_x, crtc_y,
+						    src_w, src_h, luma_stride);
+		if (ret)
+			break;
+		if (layer_id == mixer_hw->logo_layer_id) {
+			ret = xlnx_mix_update_logo_img(plane, luma_buffer,
+						       src_w, src_h);
+		} else {
+			if (!plane->mixer_layer->hw_config.is_streaming)
+				ret = xlnx_mix_set_layer_buff_addr
+					(mixer_hw, plane->mixer_layer->id,
+					 luma_addr, chroma_addr);
+		}
+	}
+	return ret;
+}
+
+/* mode set a plane */
+static int xlnx_mix_plane_mode_set(struct drm_plane *base_plane,
+				   struct drm_framebuffer *fb,
+				   int crtc_x, int crtc_y,
+				   unsigned int crtc_w, unsigned int crtc_h,
+				   u32 src_x, uint32_t src_y,
+				   u32 src_w, uint32_t src_h)
+{
+	struct xlnx_mix_plane *plane = to_xlnx_plane(base_plane);
+	struct xlnx_mix_hw *mixer_hw = to_mixer_hw(plane);
+	const struct drm_format_info *info = fb->format;
+	size_t i = 0;
+	dma_addr_t luma_paddr;
+	int ret;
+	u32 stride;
+
+	/* JPM TODO begin start of code to extract into prep-interleaved*/
+	DRM_DEBUG_KMS("plane->id: %d\n", plane->id);
+	DRM_DEBUG_KMS("h: %d(%d), v: %d(%d)\n", src_w, crtc_x, src_h, crtc_y);
+
+	/* We have multiple dma channels.  Set each per video plane */
+	for (; i < info->num_planes; i++) {
+		unsigned int width = src_w / (i ? info->hsub : 1);
+		unsigned int height = src_h / (i ? info->vsub : 1);
+
+		luma_paddr = drm_fb_cma_get_gem_addr(fb, base_plane->state, i);
+		if (!luma_paddr) {
+			DRM_ERROR("%s failed to get luma paddr\n", __func__);
+			return -EINVAL;
+		}
+
+		plane->dma[i].xt.numf = height;
+		plane->dma[i].sgl[0].size =
+			drm_format_plane_width_bytes(info, 0, width);
+		plane->dma[i].sgl[0].icg = fb->pitches[0] -
+						plane->dma[i].sgl[0].size;
+		plane->dma[i].xt.src_start = luma_paddr;
+		plane->dma[i].xt.frame_size = info->num_planes;
+		plane->dma[i].xt.dir = DMA_MEM_TO_DEV;
+		plane->dma[i].xt.src_sgl = true;
+		plane->dma[i].xt.dst_sgl = false;
+		plane->dma[i].is_active = true;
+	}
+
+	for (; i < XVMIX_MAX_NUM_SUB_PLANES; i++)
+		plane->dma[i].is_active = false;
+	/* Do we have a video format aware dma channel?
+	 * If so, modify descriptor accordingly
+	 */
+	if (plane->dma[0].chan && !plane->dma[1].chan && info->num_planes > 1) {
+		stride = plane->dma[0].sgl[0].size + plane->dma[0].sgl[0].icg;
+		plane->dma[0].sgl[0].src_icg = plane->dma[1].xt.src_start -
+				plane->dma[0].xt.src_start -
+				(plane->dma[0].xt.numf * stride);
+	}
+
+	if (mixer_hw->csc_enabled) {
+		/**
+		 * magic numbers of coefficient table for colorimetry
+		 * and range are derived from the following references:
+		 * [1] Rec. ITU-R BT.601-6
+		 * [2] Rec. ITU-R BT.709-5
+		 * [3] Rec. ITU-R BT.2020
+		 * [4] http://en.wikipedia.org/wiki/YCbCr
+		 * coefficient table supports BT601 / BT709 / BT2020 encoding
+		 * schemes and 16-235(limited) / 16-240(full) range.
+		 */
+		xlnx_mix_set_yuv2_rgb_coeff(plane,
+					    base_plane->state->color_encoding,
+					    base_plane->state->color_range);
+		xlnx_mix_set_rgb2_yuv_coeff(plane,
+					    base_plane->state->color_encoding,
+					    base_plane->state->color_range);
+	}
+
+	ret = xlnx_mix_set_plane(plane, fb, crtc_x, crtc_y, src_x, src_y,
+				 src_w, src_h);
+	return ret;
+}
+
+static int xlnx_mix_plane_prepare_fb(struct drm_plane *plane,
+				     struct drm_plane_state *new_state)
+{
+	return 0;
+}
+
+static void xlnx_mix_plane_cleanup_fb(struct drm_plane *plane,
+				      struct drm_plane_state *old_state)
+{
+}
+
+static int xlnx_mix_plane_atomic_check(struct drm_plane *plane,
+				       struct drm_atomic_state *statea)
+{
+	int scale;
+	struct xlnx_mix_plane *mix_plane = to_xlnx_plane(plane);
+	struct xlnx_mix_hw *mixer_hw = to_mixer_hw(mix_plane);
+	struct xlnx_mix *mix;
+	int scale_factor[3] = {1, 2, 4};
+	struct drm_plane_state *state = drm_atomic_get_new_plane_state(statea,
+								       plane);
+
+	/* No check required for the drm_primary_plane */
+	mix = container_of(mixer_hw, struct xlnx_mix, mixer_hw);
+	if (mix->drm_primary_layer == mix_plane)
+		return 0;
+
+	scale = xlnx_mix_get_layer_scaling(mixer_hw,
+					   mix_plane->mixer_layer->id);
+
+	if (state->fb && (((state->src_w >> 16) * scale_factor[scale] != state->crtc_w) ||
+			  ((state->src_h >> 16) * scale_factor[scale] != state->crtc_h))) {
+		DRM_DEBUG_KMS("Not possible to scale to the desired dimensions\n");
+		return -EINVAL;
+	}
+
+	if (is_window_valid(mixer_hw, state->crtc_x, state->crtc_y,
+			    state->src_w >> 16, state->src_h >> 16, scale))
+		return 0;
+
+	return -EINVAL;
+}
+
+static void xlnx_mix_plane_atomic_update(struct drm_plane *plane,
+					 struct drm_atomic_state *state)
+{
+	int ret;
+	struct drm_plane_state *old_state = drm_atomic_get_old_plane_state(state, plane);
+
+	if (!plane->state->crtc || !plane->state->fb)
+		return;
+
+	if (old_state->fb &&
+	    old_state->fb->format->format != plane->state->fb->format->format)
+		xlnx_mix_plane_dpms(plane, DRM_MODE_DPMS_OFF);
+
+	ret = xlnx_mix_plane_mode_set(plane, plane->state->fb,
+				      plane->state->crtc_x,
+				      plane->state->crtc_y,
+				      plane->state->crtc_w,
+				      plane->state->crtc_h,
+				      plane->state->src_x >> 16,
+				      plane->state->src_y >> 16,
+				      plane->state->src_w >> 16,
+				      plane->state->src_h >> 16);
+	if (ret) {
+		DRM_ERROR("failed to mode-set a plane\n");
+		return;
+	}
+	/* apply the new fb addr */
+	xlnx_mix_plane_commit(plane);
+	/* make sure a plane is on */
+	xlnx_mix_plane_dpms(plane, DRM_MODE_DPMS_ON);
+}
+
+static void xlnx_mix_plane_atomic_disable(struct drm_plane *plane,
+					  struct drm_atomic_state *state)
+{
+	xlnx_mix_plane_dpms(plane, DRM_MODE_DPMS_OFF);
+}
+
+static int xlnx_mix_plane_atomic_async_check(struct drm_plane *plane,
+					     struct drm_atomic_state *state)
+{
+	return 0;
+}
+
+static void
+xlnx_mix_plane_atomic_async_update(struct drm_plane *plane,
+				   struct drm_atomic_state *state)
+{
+	struct drm_plane_state *new_state =
+		drm_atomic_get_new_plane_state(state, plane);
+
+	/* Update the current state with new configurations */
+	swap(plane->state->fb, new_state->fb);
+	plane->state->crtc = new_state->crtc;
+	plane->state->crtc_x = new_state->crtc_x;
+	plane->state->crtc_y = new_state->crtc_y;
+	plane->state->crtc_w = new_state->crtc_w;
+	plane->state->crtc_h = new_state->crtc_h;
+	plane->state->src_x = new_state->src_x;
+	plane->state->src_y = new_state->src_y;
+	plane->state->src_w = new_state->src_w;
+	plane->state->src_h = new_state->src_h;
+	plane->state->state = new_state->state;
+
+	xlnx_mix_plane_atomic_update(plane, state);
+}
+
+static const struct drm_plane_helper_funcs xlnx_mix_plane_helper_funcs = {
+	.prepare_fb	= xlnx_mix_plane_prepare_fb,
+	.cleanup_fb	= xlnx_mix_plane_cleanup_fb,
+	.atomic_check	= xlnx_mix_plane_atomic_check,
+	.atomic_update	= xlnx_mix_plane_atomic_update,
+	.atomic_disable	= xlnx_mix_plane_atomic_disable,
+	.atomic_async_check = xlnx_mix_plane_atomic_async_check,
+	.atomic_async_update = xlnx_mix_plane_atomic_async_update,
+};
+
+static int xlnx_mix_init_plane(struct xlnx_mix_plane *plane,
+			       unsigned int poss_crtcs,
+			       struct device_node *layer_node)
+{
+	struct xlnx_mix *mixer = plane->mixer;
+	char name[16];
+	enum drm_plane_type type;
+	int ret, i;
+
+	plane->dpms = DRM_MODE_DPMS_OFF;
+	type = DRM_PLANE_TYPE_OVERLAY;
+
+	for (i = 0; i < XVMIX_MAX_NUM_SUB_PLANES; i++) {
+		snprintf(name, sizeof(name), "dma%d", i);
+		plane->dma[i].chan = of_dma_request_slave_channel(layer_node,
+								  name);
+		if (PTR_ERR(plane->dma[i].chan) == -ENODEV) {
+			plane->dma[i].chan = NULL;
+			continue;
+		}
+		if (IS_ERR(plane->dma[i].chan)) {
+			DRM_ERROR("failed to request dma channel\n");
+			ret = PTR_ERR(plane->dma[i].chan);
+			plane->dma[i].chan = NULL;
+			goto err_dma;
+		}
+	}
+	if (!xlnx_mix_isfmt_support(plane->mixer_layer->hw_config.vid_fmt)) {
+		DRM_ERROR("DRM color format not supported by mixer\n");
+		ret = -ENODEV;
+		goto err_init;
+	}
+	plane->format = plane->mixer_layer->hw_config.vid_fmt;
+	if (plane == mixer->hw_logo_layer)
+		type = DRM_PLANE_TYPE_CURSOR;
+	if (plane == mixer->drm_primary_layer)
+		type = DRM_PLANE_TYPE_PRIMARY;
+
+	/* initialize drm plane */
+	ret = drm_universal_plane_init(mixer->drm, &plane->base,
+				       poss_crtcs, &xlnx_mix_plane_funcs,
+				       &plane->format,
+				       1, NULL, type, NULL);
+
+	if (ret) {
+		DRM_ERROR("failed to initialize plane\n");
+		goto err_init;
+	}
+	drm_plane_helper_add(&plane->base, &xlnx_mix_plane_helper_funcs);
+	of_node_put(layer_node);
+
+	return 0;
+
+err_init:
+	xlnx_mix_disp_layer_disable(plane);
+err_dma:
+	for (i = 0; i < XVMIX_MAX_NUM_SUB_PLANES; i++)
+		if (plane->dma[i].chan)
+			dma_release_channel(plane->dma[i].chan);
+
+	of_node_put(layer_node);
+	return ret;
+}
+
+static int xlnx_mix_parse_dt_bg_video_fmt(struct device_node *node,
+					  struct xlnx_mix_hw *mixer_hw)
+{
+	struct device_node *layer_node;
+	struct xlnx_mix_layer_data *layer;
+	const char *vformat;
+
+	layer_node = of_get_child_by_name(node, "layer_0");
+	layer = &mixer_hw->layer_data[XVMIX_MASTER_LAYER_IDX];
+
+	/* Set default values */
+	layer->hw_config.can_alpha = false;
+	layer->hw_config.can_scale = false;
+	layer->hw_config.min_width = XVMIX_LAYER_WIDTH_MIN;
+	layer->hw_config.min_height = XVMIX_LAYER_HEIGHT_MIN;
+
+	if (of_property_read_string(layer_node, "xlnx,vformat",
+				    &vformat)) {
+		DRM_ERROR("No xlnx,vformat value for layer 0 in dts\n");
+		return -EINVAL;
+	}
+	strncpy((char *)&layer->hw_config.vid_fmt, vformat, 4);
+	layer->hw_config.is_streaming =
+		of_property_read_bool(layer_node, "xlnx,layer-streaming");
+	if (of_property_read_u32(node, "xlnx,bpc", &mixer_hw->bg_layer_bpc)) {
+		DRM_ERROR("Failed to get bits per component (bpc) prop\n");
+		return -EINVAL;
+	}
+	if (of_property_read_u32(layer_node, "xlnx,layer-max-width",
+				 &layer->hw_config.max_width)) {
+		DRM_ERROR("Failed to get screen width prop\n");
+		return -EINVAL;
+	} else if (layer->hw_config.max_width > XVMIX_DISP_MAX_WIDTH ||
+		   layer->hw_config.max_width < XVMIX_DISP_MIN_WIDTH) {
+		DRM_ERROR("Invalid width in dt");
+		return -EINVAL;
+	}
+
+	mixer_hw->max_layer_width = layer->hw_config.max_width;
+	if (of_property_read_u32(layer_node, "xlnx,layer-max-height",
+				 &layer->hw_config.max_height)) {
+		DRM_ERROR("Failed to get screen height prop\n");
+		return -EINVAL;
+	} else if (layer->hw_config.max_height > XVMIX_DISP_MAX_HEIGHT ||
+		   layer->hw_config.max_height < XVMIX_DISP_MIN_HEIGHT) {
+		DRM_ERROR("Invalid height in dt");
+		return -EINVAL;
+	}
+
+	mixer_hw->max_layer_height = layer->hw_config.max_height;
+	layer->id = XVMIX_LAYER_MASTER;
+
+	return 0;
+}
+
+static int xlnx_mix_parse_dt_logo_data(struct device_node *node,
+				       struct xlnx_mix_hw *mixer_hw)
+{
+	struct xlnx_mix_layer_data *layer_data;
+	struct device_node *logo_node;
+	u32 max_width, max_height;
+
+	logo_node = of_get_child_by_name(node, "logo");
+	if (!logo_node) {
+		DRM_ERROR("No logo node specified in device tree.\n");
+		return -EINVAL;
+	}
+
+	layer_data = &mixer_hw->layer_data[XVMIX_LOGO_LAYER_IDX];
+
+	/* set defaults for logo layer */
+	layer_data->hw_config.min_height = XVMIX_LOGO_LAYER_HEIGHT_MIN;
+	layer_data->hw_config.min_width = XVMIX_LOGO_LAYER_WIDTH_MIN;
+	layer_data->hw_config.is_streaming = false;
+	layer_data->hw_config.vid_fmt = DRM_FORMAT_RGB888;
+	layer_data->hw_config.can_alpha = true;
+	layer_data->hw_config.can_scale = true;
+	layer_data->layer_regs.buff_addr1 = 0;
+	layer_data->layer_regs.buff_addr2 = 0;
+	layer_data->id = mixer_hw->logo_layer_id;
+
+	if (of_property_read_u32(logo_node, "xlnx,logo-width", &max_width)) {
+		DRM_ERROR("Failed to get logo width prop\n");
+		return -EINVAL;
+	}
+	if (max_width > XVMIX_LOGO_LAYER_WIDTH_MAX ||
+	    max_width < XVMIX_LOGO_LAYER_WIDTH_MIN) {
+		DRM_ERROR("Illegal mixer logo layer width.\n");
+		return -EINVAL;
+	}
+	layer_data->hw_config.max_width = max_width;
+	mixer_hw->max_logo_layer_width = layer_data->hw_config.max_width;
+
+	if (of_property_read_u32(logo_node, "xlnx,logo-height", &max_height)) {
+		DRM_ERROR("Failed to get logo height prop\n");
+		return -EINVAL;
+	}
+	if (max_height > XVMIX_LOGO_LAYER_HEIGHT_MAX ||
+	    max_height < XVMIX_LOGO_LAYER_HEIGHT_MIN) {
+		DRM_ERROR("Illegal mixer logo layer height.\n");
+		return -EINVAL;
+	}
+	layer_data->hw_config.max_height = max_height;
+	mixer_hw->max_logo_layer_height = layer_data->hw_config.max_height;
+	mixer_hw->logo_pixel_alpha_enabled =
+		of_property_read_bool(logo_node, "xlnx,logo-pixel-alpha");
+	if (mixer_hw->logo_pixel_alpha_enabled)
+		layer_data->hw_config.vid_fmt = DRM_FORMAT_RGBA8888;
+
+	return 0;
+}
+
+static int xlnx_mix_dt_dp_bridge(struct device *dev, struct xlnx_mix *mixer)
+{
+	struct device_node *node, *disp_node;
+
+	node = dev->of_node;
+	/* Disp Bridge support */
+	disp_node = of_parse_phandle(node, "xlnx,disp-bridge", 0);
+	if (disp_node) {
+		mixer->disp_bridge = of_xlnx_bridge_get(disp_node);
+		if (!mixer->disp_bridge) {
+			dev_info(dev, "Didn't get disp bridge instance\n");
+			return -1;
+		}
+	} else {
+		dev_info(dev, "disp bridge property not present\n");
+		return -1;
+	}
+	return 0;
+}
+
+static int xlnx_mix_dt_parse(struct device *dev, struct xlnx_mix *mixer)
+{
+	struct xlnx_mix_plane *planes;
+	struct xlnx_mix_hw *mixer_hw;
+	struct device_node *node, *vtc_node, *port;
+	struct xlnx_mix_layer_data *l_data;
+	struct resource	res;
+	int ret, l_cnt, i;
+
+	node = dev->of_node;
+	mixer_hw = &mixer->mixer_hw;
+	mixer->dpms = DRM_MODE_DPMS_OFF;
+
+	mixer_hw->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(mixer_hw->reset_gpio)) {
+		ret = PTR_ERR(mixer_hw->reset_gpio);
+		if (ret == -EPROBE_DEFER)
+			dev_dbg(dev, "No gpio probed for mixer. Deferring\n");
+		else
+			dev_err(dev, "No reset gpio info from dts for mixer\n");
+		return ret;
+	}
+	gpiod_set_raw_value(mixer_hw->reset_gpio, 0);
+	gpiod_set_raw_value(mixer_hw->reset_gpio, 1);
+
+	ret = of_address_to_resource(node, 0, &res);
+	if (ret) {
+		dev_err(dev, "Invalid memory address for mixer %d\n", ret);
+		return ret;
+	}
+	/* Read in mandatory global dts properties */
+	mixer_hw->base = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(mixer_hw->base)) {
+		dev_err(dev, "Failed to map io mem space for mixer\n");
+		return PTR_ERR(mixer_hw->base);
+	}
+	if (of_device_is_compatible(dev->of_node, "xlnx,mixer-4.0") ||
+	    of_device_is_compatible(dev->of_node, "xlnx,mixer-5.0")) {
+		mixer_hw->max_layers = 18;
+		mixer_hw->logo_en_mask = BIT(23);
+		mixer_hw->enable_all_mask = (GENMASK(16, 0) |
+						mixer_hw->logo_en_mask);
+	} else {
+		mixer_hw->max_layers = 10;
+		mixer_hw->logo_en_mask = BIT(15);
+		mixer_hw->enable_all_mask = (GENMASK(8, 0) |
+						mixer_hw->logo_en_mask);
+	}
+	if (of_device_is_compatible(dev->of_node, "xlnx,mixer-5.0")) {
+		const char *prop_name = "xlnx,enable-csc-coefficient-register";
+
+		mixer_hw->csc_enabled = of_property_read_bool(node, prop_name);
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-layers",
+				   &mixer_hw->num_layers);
+	if (ret) {
+		dev_err(dev, "No xlnx,num-layers dts prop for mixer node\n");
+		return ret;
+	}
+	mixer_hw->logo_layer_id = mixer_hw->max_layers - 1;
+	if (mixer_hw->num_layers > mixer_hw->max_layers) {
+		dev_err(dev, "Num layer nodes in device tree > mixer max\n");
+		return -EINVAL;
+	}
+	ret = of_property_read_u32(node, "xlnx,dma-addr-width",
+				   &mixer_hw->dma_addr_size);
+	if (ret) {
+		dev_err(dev, "missing addr-width dts prop\n");
+		return ret;
+	}
+	if (mixer_hw->dma_addr_size != 32 && mixer_hw->dma_addr_size != 64) {
+		dev_err(dev, "invalid addr-width dts prop\n");
+		return -EINVAL;
+	}
+
+	/* VTC Bridge support */
+	vtc_node = of_parse_phandle(node, "xlnx,bridge", 0);
+	if (vtc_node) {
+		mixer->vtc_bridge = of_xlnx_bridge_get(vtc_node);
+		if (!mixer->vtc_bridge) {
+			dev_info(dev, "Didn't get vtc bridge instance\n");
+			return -EPROBE_DEFER;
+		}
+	} else {
+		dev_info(dev, "vtc bridge property not present\n");
+	}
+
+	mixer_hw->logo_layer_en = of_property_read_bool(node,
+							"xlnx,logo-layer");
+	l_cnt = mixer_hw->num_layers + (mixer_hw->logo_layer_en ? 1 : 0);
+	mixer_hw->layer_cnt = l_cnt;
+
+	l_data = devm_kzalloc(dev, sizeof(*l_data) * l_cnt, GFP_KERNEL);
+	if (!l_data)
+		return -ENOMEM;
+	mixer_hw->layer_data = l_data;
+	/* init DRM planes */
+	planes = devm_kzalloc(dev, sizeof(*planes) * l_cnt, GFP_KERNEL);
+	if (!planes)
+		return -ENOMEM;
+	mixer->planes = planes;
+	mixer->num_planes = l_cnt;
+	for (i = 0; i < mixer->num_planes; i++)
+		mixer->planes[i].mixer = mixer;
+
+	/* establish background layer video properties from dts */
+	ret = xlnx_mix_parse_dt_bg_video_fmt(node, mixer_hw);
+	if (ret)
+		return ret;
+	if (mixer_hw->logo_layer_en) {
+		/* read logo data from dts */
+		ret = xlnx_mix_parse_dt_logo_data(node, mixer_hw);
+		return ret;
+	}
+
+	/* Fill out crtc port OF node */
+	for_each_child_of_node(node, port) {
+		if (!port->name || of_node_cmp(port->name, "port"))
+			continue;
+		mixer->crtc.crtc.port = port;
+		break;
+	}
+	return 0;
+}
+
+static int xlnx_mix_of_init_layer(struct device *dev, struct device_node *node,
+				  char *name, struct xlnx_mix_layer_data *layer,
+				  u32 max_width, struct xlnx_mix *mixer, int id)
+{
+	struct device_node *layer_node;
+	const char *vformat;
+	int ret;
+
+	layer_node = of_get_child_by_name(node, name);
+	if (!layer_node)
+		return -EINVAL;
+
+	/* Set default values */
+	layer->hw_config.can_alpha = false;
+	layer->hw_config.can_scale = false;
+	layer->hw_config.is_streaming = false;
+	layer->hw_config.max_width = max_width;
+	layer->hw_config.min_width = XVMIX_LAYER_WIDTH_MIN;
+	layer->hw_config.min_height = XVMIX_LAYER_HEIGHT_MIN;
+	layer->hw_config.vid_fmt = 0;
+	layer->id = 0;
+	mixer->planes[id].mixer_layer = layer;
+
+	ret = of_property_read_u32(layer_node, "xlnx,layer-id", &layer->id);
+	if (ret) {
+		dev_err(dev, "xlnx,layer-id property not found\n");
+		return ret;
+	}
+	if (layer->id < 1 || layer->id >= mixer->mixer_hw.max_layers) {
+		dev_err(dev, "Mixer layer id %u in dts is out of legal range\n",
+			layer->id);
+		return -EINVAL;
+	}
+	ret = of_property_read_string(layer_node, "xlnx,vformat", &vformat);
+	if (ret) {
+		dev_err(dev, "No mixer layer vformat in dts for layer id %d\n",
+			layer->id);
+		return ret;
+	}
+
+	strncpy((char *)&layer->hw_config.vid_fmt, vformat, 4);
+	layer->hw_config.can_scale =
+		    of_property_read_bool(layer_node, "xlnx,layer-scale");
+	if (layer->hw_config.can_scale) {
+		ret = of_property_read_u32(layer_node, "xlnx,layer-max-width",
+					   &layer->hw_config.max_width);
+		if (ret) {
+			dev_err(dev, "Mixer layer %d dts missing width prop.\n",
+				layer->id);
+			return ret;
+		}
+
+		if (layer->hw_config.max_width > max_width) {
+			dev_err(dev, "Illlegal Mixer layer %d width %d\n",
+				layer->id, layer->hw_config.max_width);
+			return -EINVAL;
+		}
+	}
+	layer->hw_config.can_alpha =
+		    of_property_read_bool(layer_node, "xlnx,layer-alpha");
+	layer->hw_config.is_streaming =
+		    of_property_read_bool(layer_node, "xlnx,layer-streaming");
+	if (of_property_read_bool(layer_node, "xlnx,layer-primary")) {
+		if (mixer->drm_primary_layer) {
+			dev_err(dev,
+				"More than one primary layer in mixer dts\n");
+			return -EINVAL;
+		}
+		mixer->drm_primary_layer = &mixer->planes[id];
+	}
+	ret = xlnx_mix_init_plane(&mixer->planes[id], 1, layer_node);
+	if (ret)
+		dev_err(dev, "Unable to init drm mixer plane id = %u", id);
+
+	return ret;
+}
+
+static irqreturn_t xlnx_mix_intr_handler(int irq, void *data)
+{
+	struct xlnx_mix_hw *mixer = data;
+	u32 intr = xlnx_mix_get_intr_status(mixer);
+
+	if (!intr)
+		return IRQ_NONE;
+	if (mixer->intrpt_handler_fn)
+		mixer->intrpt_handler_fn(mixer->intrpt_data);
+	xlnx_mix_clear_intr_status(mixer, intr);
+
+	return IRQ_HANDLED;
+}
+
+static void xlnx_mix_create_plane_properties(struct xlnx_mix *mixer)
+{
+	mixer->scale_prop = drm_property_create_range(mixer->drm, 0, "scale",
+						      XVMIX_SCALE_FACTOR_1X,
+						      XVMIX_SCALE_FACTOR_4X);
+	mixer->alpha_prop = drm_property_create_range(mixer->drm, 0, "alpha",
+						      XVMIX_ALPHA_MIN,
+						      XVMIX_ALPHA_MAX);
+}
+
+static int xlnx_mix_plane_create(struct device *dev, struct xlnx_mix *mixer)
+{
+	struct xlnx_mix_hw		*mixer_hw;
+	struct device_node		*node, *layer_node;
+	char				name[20];
+	struct xlnx_mix_layer_data	*layer_data;
+	int				ret, i;
+	int				layer_idx;
+
+	node = dev->of_node;
+	mixer_hw = &mixer->mixer_hw;
+	xlnx_mix_create_plane_properties(mixer);
+
+	mixer->planes[XVMIX_MASTER_LAYER_IDX].mixer_layer =
+				&mixer_hw->layer_data[XVMIX_MASTER_LAYER_IDX];
+	mixer->planes[XVMIX_MASTER_LAYER_IDX].id = XVMIX_MASTER_LAYER_IDX;
+	mixer->hw_master_layer = &mixer->planes[XVMIX_MASTER_LAYER_IDX];
+
+	if (mixer_hw->logo_layer_en) {
+		mixer->planes[XVMIX_LOGO_LAYER_IDX].mixer_layer =
+				&mixer_hw->layer_data[XVMIX_LOGO_LAYER_IDX];
+		mixer->planes[XVMIX_LOGO_LAYER_IDX].id = XVMIX_LOGO_LAYER_IDX;
+		mixer->hw_logo_layer = &mixer->planes[XVMIX_LOGO_LAYER_IDX];
+		layer_node = of_get_child_by_name(node, "logo");
+		ret = xlnx_mix_init_plane(&mixer->planes[XVMIX_LOGO_LAYER_IDX],
+					  1, layer_node);
+		if (ret)
+			return ret;
+	}
+	layer_idx = mixer_hw->logo_layer_en ? 2 : 1;
+	for (i = 1; i < mixer_hw->num_layers; i++, layer_idx++) {
+		snprintf(name, sizeof(name), "layer_%d", i);
+		ret = xlnx_mix_of_init_layer(dev, node, name,
+					     &mixer_hw->layer_data[layer_idx],
+					     mixer_hw->max_layer_width,
+					     mixer, layer_idx);
+		if (ret)
+			return ret;
+	}
+	/* If none of the overlay layers were designated as the drm
+	 * primary layer, default to the mixer's video0 layer as drm primary
+	 */
+	if (!mixer->drm_primary_layer)
+		mixer->drm_primary_layer = mixer->hw_master_layer;
+	layer_node = of_get_child_by_name(node, "layer_0");
+	ret = xlnx_mix_init_plane(&mixer->planes[XVMIX_MASTER_LAYER_IDX], 1,
+				  layer_node);
+	/* request irq and obtain pixels-per-clock (ppc) property */
+	mixer_hw->irq = irq_of_parse_and_map(node, 0);
+	if (mixer_hw->irq > 0) {
+		ret = devm_request_irq(dev, mixer_hw->irq,
+				       xlnx_mix_intr_handler,
+				       IRQF_SHARED, "xlnx-mixer", mixer_hw);
+		if (ret) {
+			dev_err(dev, "Failed to request irq\n");
+			return ret;
+		}
+	}
+	ret = of_property_read_u32(node, "xlnx,ppc", &mixer_hw->ppc);
+	if (ret) {
+		dev_err(dev, "No xlnx,ppc property for mixer dts\n");
+		return ret;
+	}
+
+	mixer->max_width = mixer_hw->max_layer_width;
+	mixer->max_height = mixer_hw->max_layer_height;
+
+	if (mixer->hw_logo_layer) {
+		layer_data = &mixer_hw->layer_data[XVMIX_LOGO_LAYER_IDX];
+		mixer->max_cursor_width = layer_data->hw_config.max_width;
+		mixer->max_cursor_height = layer_data->hw_config.max_height;
+	}
+	return 0;
+}
+
+/**
+ * xlnx_mix_plane_restore - Restore the plane states
+ * @mixer: mixer device core structure
+ *
+ * Restore the plane states to the default ones. Any state that needs to be
+ * restored should be here. This improves consistency as applications see
+ * the same default values, and removes mismatch between software and hardware
+ * values as software values are updated as hardware values are reset.
+ */
+static void xlnx_mix_plane_restore(struct xlnx_mix *mixer)
+{
+	struct xlnx_mix_plane *plane;
+	unsigned int i;
+
+	if (!mixer)
+		return;
+	/*
+	 * Reinitialize property default values as they get reset by DPMS OFF
+	 * operation. User will read the correct default values later, and
+	 * planes will be initialized with default values.
+	 */
+	for (i = 0; i < mixer->num_planes; i++) {
+		plane = &mixer->planes[i];
+		if (!plane)
+			continue;
+		xlnx_mix_hw_plane_dpms(plane, DRM_MODE_DPMS_OFF);
+	}
+}
+
+/**
+ * xlnx_mix_set_bkg_col - Set background color
+ * @mixer: Mixer instance to program with new background color
+ * @rgb_value: RGB encoded as 32-bit integer in little-endian format
+ *
+ * Set the color to be output as background color when background stream layer
+ */
+static void xlnx_mix_set_bkg_col(struct xlnx_mix_hw *mixer, u64 rgb_value)
+{
+	u32 bg_bpc = mixer->bg_layer_bpc;
+	u32 bpc_mask_shift = XVMIX_MAX_BPC - bg_bpc;
+	u32 val_mask = (GENMASK(15, 0) >> bpc_mask_shift);
+	u16 b_val = (rgb_value >> (bg_bpc * 2)) & val_mask;
+	u16 g_val = (rgb_value >> bg_bpc) & val_mask;
+	u16 r_val = (rgb_value >> 0) &  val_mask;
+
+	/* Set Background Color */
+	reg_writel(mixer->base, XVMIX_BACKGROUND_Y_R_DATA, r_val);
+	reg_writel(mixer->base, XVMIX_BACKGROUND_U_G_DATA, g_val);
+	reg_writel(mixer->base, XVMIX_BACKGROUND_V_B_DATA, b_val);
+	mixer->bg_color = rgb_value;
+}
+
+/**
+ * xlnx_mix_reset - Reset the mixer core video generator
+ * @mixer: Mixer core instance for which to start video output
+ *
+ * Toggle the reset gpio and restores the bg color, plane and interrupt mask.
+ */
+static void xlnx_mix_reset(struct xlnx_mix *mixer)
+{
+	struct xlnx_mix_hw *mixer_hw = &mixer->mixer_hw;
+
+	gpiod_set_raw_value(mixer_hw->reset_gpio, 0);
+	gpiod_set_raw_value(mixer_hw->reset_gpio, 1);
+	/* restore layer properties and bg color after reset */
+	xlnx_mix_set_bkg_col(mixer_hw, mixer_hw->bg_color);
+	xlnx_mix_plane_restore(mixer);
+	xlnx_mix_intrpt_enable_done(&mixer->mixer_hw);
+}
+
+static void xlnx_mix_dpms(struct xlnx_mix *mixer, int dpms)
+{
+	switch (dpms) {
+	case DRM_MODE_DPMS_ON:
+		xlnx_mix_start(&mixer->mixer_hw);
+		break;
+	default:
+		xlnx_mix_stop(&mixer->mixer_hw);
+		mdelay(50); /* let IP shut down */
+		xlnx_mix_reset(mixer);
+	}
+}
+
+/* set crtc dpms */
+static void xlnx_mix_crtc_dpms(struct drm_crtc *base_crtc, int dpms)
+{
+	struct xlnx_crtc *crtc = to_xlnx_crtc(base_crtc);
+	struct xlnx_mix *mixer = to_xlnx_mixer(crtc);
+	int ret;
+	struct videomode vm;
+	struct drm_display_mode *mode = &base_crtc->mode;
+	struct drm_display_mode *adjusted_mode =
+					&base_crtc->state->adjusted_mode;
+
+	DRM_DEBUG_KMS("dpms: %d\n", dpms);
+	if (mixer->dpms == dpms)
+		return;
+	mixer->dpms = dpms;
+
+	switch (dpms) {
+	case DRM_MODE_DPMS_ON:
+		if (!mixer->pixel_clock_enabled) {
+			ret = clk_prepare_enable(mixer->pixel_clock);
+			if (ret) {
+				DRM_ERROR("failed to enable a pixel clock\n");
+				mixer->pixel_clock_enabled = false;
+			}
+		}
+		mixer->pixel_clock_enabled = true;
+
+		if (mixer->vtc_bridge) {
+			drm_display_mode_to_videomode(mode, &vm);
+			xlnx_bridge_set_timing(mixer->vtc_bridge, &vm);
+			xlnx_bridge_enable(mixer->vtc_bridge);
+		}
+
+		if (mixer->disp_bridge) {
+			drm_display_mode_to_videomode(adjusted_mode, &vm);
+			xlnx_bridge_set_input(mixer->disp_bridge,
+					      adjusted_mode->hdisplay,
+					      adjusted_mode->vdisplay,
+					      xlnx_mix_get_bus_fmt(mixer));
+			xlnx_bridge_set_timing(mixer->disp_bridge, &vm);
+			xlnx_bridge_enable(mixer->disp_bridge);
+		}
+
+		xlnx_mix_dpms(mixer, dpms);
+		xlnx_mix_plane_dpms(base_crtc->primary, dpms);
+		break;
+	default:
+		xlnx_mix_plane_dpms(base_crtc->primary, dpms);
+		xlnx_mix_dpms(mixer, dpms);
+		xlnx_bridge_disable(mixer->vtc_bridge);
+		if (mixer->pixel_clock_enabled) {
+			clk_disable_unprepare(mixer->pixel_clock);
+			mixer->pixel_clock_enabled = false;
+		}
+		break;
+	}
+}
+
+static void xlnx_mix_set_intr_handler(struct xlnx_mix *mixer,
+				      void (*intr_handler_fn)(void *),
+				       void *data)
+{
+	mixer->mixer_hw.intrpt_handler_fn = intr_handler_fn;
+	mixer->mixer_hw.intrpt_data = data;
+}
+
+static void xlnx_mix_crtc_vblank_handler(void *data)
+{
+	struct drm_crtc *base_crtc = data;
+	struct xlnx_crtc *crtc = to_xlnx_crtc(base_crtc);
+	struct xlnx_mix *mixer = to_xlnx_mixer(crtc);
+	struct drm_device *drm = base_crtc->dev;
+	struct drm_pending_vblank_event *event;
+	unsigned long flags;
+
+	drm_crtc_handle_vblank(base_crtc);
+	/* Finish page flip */
+	spin_lock_irqsave(&drm->event_lock, flags);
+	event = mixer->event;
+	mixer->event = NULL;
+	if (event) {
+		drm_crtc_send_vblank_event(base_crtc, event);
+		drm_crtc_vblank_put(base_crtc);
+	}
+	spin_unlock_irqrestore(&drm->event_lock, flags);
+}
+
+static int xlnx_mix_crtc_enable_vblank(struct drm_crtc *base_crtc)
+{
+	struct xlnx_crtc *crtc = to_xlnx_crtc(base_crtc);
+	struct xlnx_mix *mixer = to_xlnx_mixer(crtc);
+
+	xlnx_mix_set_intr_handler(mixer, xlnx_mix_crtc_vblank_handler,
+				  base_crtc);
+	return 0;
+}
+
+static void xlnx_mix_crtc_disable_vblank(struct drm_crtc *base_crtc)
+{
+	struct xlnx_crtc *crtc = to_xlnx_crtc(base_crtc);
+	struct xlnx_mix *mixer = to_xlnx_mixer(crtc);
+
+	mixer->mixer_hw.intrpt_handler_fn = NULL;
+	mixer->mixer_hw.intrpt_data = NULL;
+}
+
+static void xlnx_mix_crtc_destroy(struct drm_crtc *base_crtc)
+{
+	struct xlnx_crtc *crtc = to_xlnx_crtc(base_crtc);
+	struct xlnx_mix *mixer = to_xlnx_mixer(crtc);
+
+	/* make sure crtc is off */
+	mixer->alpha_prop = NULL;
+	mixer->scale_prop = NULL;
+	mixer->bg_color = NULL;
+	xlnx_mix_crtc_dpms(base_crtc, DRM_MODE_DPMS_OFF);
+
+	if (mixer->pixel_clock_enabled) {
+		clk_disable_unprepare(mixer->pixel_clock);
+		mixer->pixel_clock_enabled = false;
+	}
+	drm_crtc_cleanup(base_crtc);
+}
+
+static int
+xlnx_mix_disp_crtc_atomic_set_property(struct drm_crtc *crtc,
+				       struct drm_crtc_state *state,
+				     struct drm_property *property,
+				     uint64_t val)
+{
+	return 0;
+}
+
+static int
+xlnx_mix_disp_crtc_atomic_get_property(struct drm_crtc *crtc,
+				       const struct drm_crtc_state *state,
+				     struct drm_property *property,
+				     uint64_t *val)
+{
+	return 0;
+}
+
+static struct drm_crtc_funcs xlnx_mix_crtc_funcs = {
+	.destroy		= xlnx_mix_crtc_destroy,
+	.set_config		= drm_atomic_helper_set_config,
+	.page_flip		= drm_atomic_helper_page_flip,
+	.atomic_set_property	= xlnx_mix_disp_crtc_atomic_set_property,
+	.atomic_get_property	= xlnx_mix_disp_crtc_atomic_get_property,
+	.reset			= drm_atomic_helper_crtc_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_crtc_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_crtc_destroy_state,
+	.enable_vblank		= xlnx_mix_crtc_enable_vblank,
+	.disable_vblank		= xlnx_mix_crtc_disable_vblank,
+};
+
+static void
+xlnx_mix_crtc_atomic_enable(struct drm_crtc *crtc,
+			    struct drm_atomic_state *state)
+{
+	struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode;
+	int vrefresh;
+
+	xlnx_mix_crtc_dpms(crtc, DRM_MODE_DPMS_ON);
+
+	/* Delay of 3 vblank interval for timing gen to be stable */
+	vrefresh = ((adjusted_mode->clock * 1000) /
+		    (adjusted_mode->vtotal * adjusted_mode->htotal));
+	msleep(3 * 1000 / vrefresh);
+}
+
+/**
+ * xlnx_mix_clear_event - Clear any event if pending
+ * @crtc: DRM crtc object
+ *
+ */
+static void xlnx_mix_clear_event(struct drm_crtc *crtc)
+{
+	if (crtc->state->event) {
+		complete_all(crtc->state->event->base.completion);
+		crtc->state->event = NULL;
+	}
+}
+
+static void
+xlnx_mix_crtc_atomic_disable(struct drm_crtc *crtc,
+			     struct drm_atomic_state *state)
+{
+	xlnx_mix_crtc_dpms(crtc, DRM_MODE_DPMS_OFF);
+	xlnx_mix_clear_event(crtc);
+	drm_crtc_vblank_off(crtc);
+}
+
+static void xlnx_mix_crtc_mode_set_nofb(struct drm_crtc *crtc)
+{
+}
+
+static int xlnx_mix_crtc_atomic_check(struct drm_crtc *crtc,
+				      struct drm_atomic_state *state)
+{
+	return drm_atomic_add_affected_planes(state, crtc);
+}
+
+static void
+xlnx_mix_crtc_atomic_begin(struct drm_crtc *crtc,
+			   struct drm_atomic_state *state)
+{
+	drm_crtc_vblank_on(crtc);
+	/* Don't rely on vblank when disabling crtc */
+	if (crtc->state->event) {
+		struct xlnx_crtc *xcrtc = to_xlnx_crtc(crtc);
+		struct xlnx_mix *mixer = to_xlnx_mixer(xcrtc);
+
+		/* Consume the flip_done event from atomic helper */
+		crtc->state->event->pipe = drm_crtc_index(crtc);
+		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
+		mixer->event = crtc->state->event;
+		crtc->state->event = NULL;
+	}
+}
+
+static struct drm_crtc_helper_funcs xlnx_mix_crtc_helper_funcs = {
+	.atomic_enable	= xlnx_mix_crtc_atomic_enable,
+	.atomic_disable	= xlnx_mix_crtc_atomic_disable,
+	.mode_set_nofb	= xlnx_mix_crtc_mode_set_nofb,
+	.atomic_check	= xlnx_mix_crtc_atomic_check,
+	.atomic_begin	= xlnx_mix_crtc_atomic_begin,
+};
+
+/**
+ * xlnx_mix_crtc_create - create crtc for mixer
+ * @mixer: xilinx video mixer object
+ *
+ * Return:
+ * Zero on success, error on failure
+ *
+ */
+static int xlnx_mix_crtc_create(struct xlnx_mix *mixer)
+{
+	struct xlnx_crtc *crtc;
+	int ret, i;
+
+	crtc = &mixer->crtc;
+
+	for (i = 0; i < mixer->num_planes; i++)
+		xlnx_mix_attach_plane_prop(&mixer->planes[i]);
+	mixer->pixel_clock = devm_clk_get(mixer->drm->dev, NULL);
+	if (IS_ERR(mixer->pixel_clock)) {
+		DRM_DEBUG_KMS("failed to get pixel clock\n");
+		mixer->pixel_clock = NULL;
+	}
+	ret = clk_prepare_enable(mixer->pixel_clock);
+	if (ret) {
+		DRM_ERROR("failed to enable a pixel clock\n");
+		mixer->pixel_clock_enabled = false;
+		goto err_plane;
+	}
+	mixer->pixel_clock_enabled = true;
+	/* initialize drm crtc */
+	ret = drm_crtc_init_with_planes(mixer->drm, &crtc->crtc,
+					&mixer->drm_primary_layer->base,
+					&mixer->hw_logo_layer->base,
+					&xlnx_mix_crtc_funcs, NULL);
+	if (ret) {
+		DRM_ERROR("failed to initialize mixer crtc\n");
+		goto err_pixel_clk;
+	}
+	drm_crtc_helper_add(&crtc->crtc, &xlnx_mix_crtc_helper_funcs);
+	crtc->get_max_width = &xlnx_mix_crtc_get_max_width;
+	crtc->get_max_height = &xlnx_mix_crtc_get_max_height;
+	crtc->get_align = &xlnx_mix_crtc_get_align;
+	crtc->get_format = &xlnx_mix_crtc_get_format;
+	crtc->get_cursor_height = &xlnx_mix_crtc_get_max_cursor_height;
+	crtc->get_cursor_width = &xlnx_mix_crtc_get_max_cursor_width;
+	xlnx_crtc_register(mixer->drm, crtc);
+	dev_info(mixer->drm->dev,
+		 "Registered mixer CRTC with id: %d\n", crtc->crtc.base.id);
+
+	return 0;
+
+err_pixel_clk:
+	if (mixer->pixel_clock_enabled) {
+		clk_disable_unprepare(mixer->pixel_clock);
+		mixer->pixel_clock_enabled = false;
+	}
+err_plane:
+	return ret;
+}
+
+/**
+ * xlnx_mix_init - Establishes a default power-on state for the mixer IP
+ * core
+ * @mixer: instance of IP core to initialize to a default state
+ *
+ * Background layer initialized to maximum height and width settings based on
+ * device tree properties and all overlay layers set to minimum height and width
+ * sizes and positioned to 0,0 in the crtc.   All layers are inactive (resulting
+ * in video output being generated by the background color generator).
+ * Interrupts are disabled and the IP is started (with auto-restart enabled).
+ */
+static void xlnx_mix_init(struct xlnx_mix_hw *mixer)
+{
+	u32 i;
+	u32 bg_bpc = mixer->bg_layer_bpc;
+	u64 rgb_bg_clr = (0xFFFF >> (XVMIX_MAX_BPC - bg_bpc)) << (bg_bpc * 2);
+	enum xlnx_mix_layer_id layer_id;
+	struct xlnx_mix_layer_data *layer_data;
+
+	layer_data = xlnx_mix_get_layer_data(mixer, XVMIX_LAYER_MASTER);
+	xlnx_mix_layer_disable(mixer, mixer->max_layers);
+	xlnx_mix_set_active_area(mixer, layer_data->hw_config.max_width,
+				 layer_data->hw_config.max_height);
+	/* default to blue */
+	xlnx_mix_set_bkg_col(mixer, rgb_bg_clr);
+
+	for (i = 0; i < mixer->layer_cnt; i++) {
+		layer_id = mixer->layer_data[i].id;
+		layer_data = &mixer->layer_data[i];
+		if (layer_id == XVMIX_LAYER_MASTER)
+			continue;
+		xlnx_mix_set_layer_window(mixer, layer_id, 0, 0,
+					  XVMIX_LAYER_WIDTH_MIN,
+					  XVMIX_LAYER_HEIGHT_MIN, 0);
+		if (layer_data->hw_config.can_scale)
+			xlnx_mix_set_layer_scaling(mixer, layer_id, 0);
+		if (layer_data->hw_config.can_alpha)
+			xlnx_mix_set_layer_alpha(mixer, layer_id,
+						 XVMIX_ALPHA_MAX);
+	}
+	xlnx_mix_intrpt_enable_done(mixer);
+}
+
+static int xlnx_mix_bind(struct device *dev, struct device *master,
+			 void *data)
+{
+	struct xlnx_mix *mixer = dev_get_drvdata(dev);
+	struct drm_device *drm = data;
+	u32 ret;
+
+	xlnx_mix_dt_dp_bridge(dev, mixer);
+
+	mixer->drm = drm;
+	ret = xlnx_mix_plane_create(dev, mixer);
+	if (ret)
+		return ret;
+	ret = xlnx_mix_crtc_create(mixer);
+	if (ret)
+		return ret;
+	xlnx_mix_init(&mixer->mixer_hw);
+
+	return ret;
+}
+
+static void xlnx_mix_unbind(struct device *dev, struct device *master,
+			    void *data)
+{
+	struct xlnx_mix *mixer = dev_get_drvdata(dev);
+	int i, j;
+
+	for (i = 0; i < mixer->num_planes; i++) {
+		for (j = 0; j < XVMIX_MAX_NUM_SUB_PLANES; j++) {
+			if (mixer->planes[i].dma[j].chan)
+				dma_release_channel(mixer->planes[i].dma[j].chan);
+		}
+	}
+
+	dev_set_drvdata(dev, NULL);
+	xlnx_mix_intrpt_disable(&mixer->mixer_hw);
+	xlnx_crtc_unregister(mixer->drm, &mixer->crtc);
+}
+
+static const struct component_ops xlnx_mix_component_ops = {
+	.bind	= xlnx_mix_bind,
+	.unbind	= xlnx_mix_unbind,
+};
+
+static int xlnx_mix_probe(struct platform_device *pdev)
+{
+	struct xlnx_mix *mixer;
+	int ret;
+
+	mixer = devm_kzalloc(&pdev->dev, sizeof(*mixer), GFP_KERNEL);
+	if (!mixer)
+		return -ENOMEM;
+
+	ret = of_reserved_mem_device_init(&pdev->dev);
+	if (ret)
+		dev_dbg(&pdev->dev, "of_reserved_mem_device_init: %d\n", ret);
+
+	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	if (ret) {
+		dev_err(&pdev->dev, "dma_set_coherent_mask: %d\n", ret);
+		return ret;
+	}
+
+	/* Sub-driver will access mixer from drvdata */
+	platform_set_drvdata(pdev, mixer);
+	ret = xlnx_mix_dt_parse(&pdev->dev, mixer);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Failed to probe mixer\n");
+		return ret;
+	}
+
+	ret = component_add(&pdev->dev, &xlnx_mix_component_ops);
+	if (ret)
+		goto err;
+
+	mixer->master = xlnx_drm_pipeline_init(pdev);
+	if (IS_ERR(mixer->master)) {
+		dev_err(&pdev->dev, "Failed to initialize the drm pipeline\n");
+		goto err_component;
+	}
+
+	dev_info(&pdev->dev, "Xilinx Mixer driver probed success\n");
+	return ret;
+
+err_component:
+	component_del(&pdev->dev, &xlnx_mix_component_ops);
+err:
+	return ret;
+}
+
+static int xlnx_mix_remove(struct platform_device *pdev)
+{
+	struct xlnx_mix *mixer = platform_get_drvdata(pdev);
+
+	if (mixer->vtc_bridge)
+		of_xlnx_bridge_put(mixer->vtc_bridge);
+	if (mixer->disp_bridge) {
+		of_xlnx_bridge_put(mixer->disp_bridge);
+		xlnx_mix_crtc_atomic_disable(&mixer->crtc.crtc, NULL);
+	}
+	xlnx_drm_pipeline_exit(mixer->master);
+	component_del(&pdev->dev, &xlnx_mix_component_ops);
+	return 0;
+}
+
+/*
+ * TODO:
+ * In Mixer IP core version 4.0, layer enable bits and logo layer offsets
+ * have been changed. To provide backward compatibility number of max layers
+ * field has been taken to differentiate IP versions.
+ * This logic will have to be changed properly using the IP core version.
+ */
+
+static const struct of_device_id xlnx_mix_of_match[] = {
+	{ .compatible = "xlnx,mixer-3.0", },
+	{ .compatible = "xlnx,mixer-4.0", },
+	{ .compatible = "xlnx,mixer-5.0", },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xlnx_mix_of_match);
+
+static struct platform_driver xlnx_mix_driver = {
+	.probe			= xlnx_mix_probe,
+	.remove			= xlnx_mix_remove,
+	.driver			= {
+		.name		= "xlnx-mixer",
+		.of_match_table	= xlnx_mix_of_match,
+	},
+};
+
+module_platform_driver(xlnx_mix_driver);
+
+MODULE_AUTHOR("Saurabh Sengar");
+MODULE_DESCRIPTION("Xilinx Mixer Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_pl_disp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_pl_disp.c
@@ -0,0 +1,687 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM CRTC DMA engine driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author : Saurabh Sengar <saurabhs@xilinx.com>
+ *        : Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ */
+
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_vblank.h>
+#include <linux/component.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dmaengine.h>
+#include <linux/dma/xilinx_frmbuf.h>
+#include <linux/of.h>
+#include <linux/of_dma.h>
+#include <linux/platform_device.h>
+#include <video/videomode.h>
+#include "xlnx_bridge.h"
+#include "xlnx_crtc.h"
+#include "xlnx_drv.h"
+
+#define XLNX_PL_DISP_MAX_NUM_PLANES	3
+/*
+ * Overview
+ * --------
+ *
+ * This driver intends to support the display pipeline with DMA engine
+ * driver by initializing DRM crtc and plane objects. The driver makes
+ * an assumption that it's single plane pipeline, as multi-plane pipeline
+ * would require programing beyond the DMA engine interface.
+ */
+
+/**
+ * struct xlnx_dma_chan - struct for DMA engine
+ * @dma_chan: DMA channel
+ * @xt: Interleaved desc config container
+ * @sgl: Data chunk for dma_interleaved_template
+ */
+struct xlnx_dma_chan {
+	struct dma_chan *dma_chan;
+	struct dma_interleaved_template xt;
+	struct data_chunk sgl[1];
+};
+
+/**
+ * struct xlnx_pl_disp - struct for display subsystem
+ * @dev: device structure
+ * @master: logical master device from xlnx drm
+ * @xlnx_crtc: Xilinx DRM driver crtc object
+ * @plane: base drm plane object
+ * @chan: struct for DMA engine
+ * @event: vblank pending event
+ * @callback: callback for registering DMA callback function
+ * @callback_param: parameter for passing  to DMA callback function
+ * @drm: core drm object
+ * @fmt: drm color format
+ * @vtc_bridge: vtc_bridge structure
+ * @fid: field id
+ * @fid_err_prop: field id error property
+ * @fid_err_val: field id error value
+ * @fid_out_prop: field id out property
+ * @fid_out_val: field out value
+ */
+struct xlnx_pl_disp {
+	struct device *dev;
+	struct platform_device *master;
+	struct xlnx_crtc xlnx_crtc;
+	struct drm_plane plane;
+	struct xlnx_dma_chan *chan;
+	struct drm_pending_vblank_event *event;
+	dma_async_tx_callback callback;
+	void *callback_param;
+	struct drm_device *drm;
+	u32 fmt;
+	struct xlnx_bridge *vtc_bridge;
+	u32 fid;
+	struct drm_property *fid_err_prop;
+	u32 fid_err_val;
+	struct drm_property *fid_out_prop;
+	u32 fid_out_val;
+};
+
+/*
+ * Xlnx crtc functions
+ */
+static inline struct xlnx_pl_disp *crtc_to_dma(struct xlnx_crtc *xlnx_crtc)
+{
+	return container_of(xlnx_crtc, struct xlnx_pl_disp, xlnx_crtc);
+}
+
+/**
+ * xlnx_pl_disp_complete - vblank handler
+ * @param: parameter to vblank handler
+ *
+ * This function handles the vblank interrupt, and sends an event to
+ * CRTC object.
+ */
+static void xlnx_pl_disp_complete(void *param)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = param;
+	struct drm_device *drm = xlnx_pl_disp->drm;
+	struct xlnx_dma_chan *xlnx_dma_chan = xlnx_pl_disp->chan;
+	int ret;
+
+	/* Get fid err flag and fid out val */
+	ret = xilinx_xdma_get_fid_err_flag(xlnx_dma_chan->dma_chan,
+					   &xlnx_pl_disp->fid_err_val);
+	if (ret)
+		dev_dbg(xlnx_pl_disp->dev, "failed to get fid_err info\n");
+
+	ret = xilinx_xdma_get_fid_out(xlnx_dma_chan->dma_chan,
+				      &xlnx_pl_disp->fid_out_val);
+	if (ret)
+		dev_dbg(xlnx_pl_disp->dev, "failed to get fid_out info\n");
+
+	drm_handle_vblank(drm, 0);
+}
+
+/**
+ * xlnx_pl_disp_get_format - Get the current display pipeline format
+ * @xlnx_crtc: xlnx crtc object
+ *
+ * Get the current format of pipeline
+ *
+ * Return: the corresponding DRM_FORMAT_XXX
+ */
+static uint32_t xlnx_pl_disp_get_format(struct xlnx_crtc *xlnx_crtc)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = crtc_to_dma(xlnx_crtc);
+
+	return xlnx_pl_disp->fmt;
+}
+
+/**
+ * xlnx_pl_disp_get_align - Get the alignment value for pitch
+ * @xlnx_crtc: xlnx crtc object
+ *
+ * Get the alignment value for pitch from the plane
+ *
+ * Return: The alignment value if successful, or the error code.
+ */
+static unsigned int xlnx_pl_disp_get_align(struct xlnx_crtc *xlnx_crtc)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = crtc_to_dma(xlnx_crtc);
+
+	return 1 << xlnx_pl_disp->chan->dma_chan->device->copy_align;
+}
+
+/*
+ * DRM plane functions
+ */
+static inline struct xlnx_pl_disp *plane_to_dma(struct drm_plane *plane)
+{
+	return container_of(plane, struct xlnx_pl_disp, plane);
+}
+
+/**
+ * xlnx_pl_disp_plane_disable - Disables DRM plane
+ * @plane: DRM plane object
+ *
+ * Disable the DRM plane, by stopping the corrosponding DMA
+ */
+static void xlnx_pl_disp_plane_disable(struct drm_plane *plane)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = plane_to_dma(plane);
+	struct xlnx_dma_chan *xlnx_dma_chan = xlnx_pl_disp->chan;
+
+	dmaengine_terminate_sync(xlnx_dma_chan->dma_chan);
+}
+
+/**
+ * xlnx_pl_disp_plane_enable - Enables DRM plane
+ * @plane: DRM plane object
+ *
+ * Enable the DRM plane, by enabling the corresponding DMA
+ */
+static void xlnx_pl_disp_plane_enable(struct drm_plane *plane)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = plane_to_dma(plane);
+	struct dma_async_tx_descriptor *desc;
+	unsigned long flags;
+	struct xlnx_dma_chan *xlnx_dma_chan = xlnx_pl_disp->chan;
+	struct dma_chan *dma_chan = xlnx_dma_chan->dma_chan;
+	struct dma_interleaved_template *xt = &xlnx_dma_chan->xt;
+
+	flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+	desc = dmaengine_prep_interleaved_dma(dma_chan, xt, flags);
+	if (!desc) {
+		dev_err(xlnx_pl_disp->dev,
+			"failed to prepare DMA descriptor\n");
+		return;
+	}
+	desc->callback = xlnx_pl_disp->callback;
+	desc->callback_param = xlnx_pl_disp->callback_param;
+	xilinx_xdma_set_earlycb(xlnx_dma_chan->dma_chan, desc, EARLY_CALLBACK);
+
+	if (plane->state->crtc->state->adjusted_mode.flags &
+			DRM_MODE_FLAG_INTERLACE) {
+		/*
+		 * Framebuffer DMA Reader sends the first field twice, which
+		 * causes the following fields out of order. The fid is
+		 * reverted to restore the order
+		 */
+		if (plane->state->fb->flags == DRM_MODE_FB_ALTERNATE_TOP) {
+			xlnx_pl_disp->fid = 0;
+		} else if (plane->state->fb->flags ==
+				DRM_MODE_FB_ALTERNATE_BOTTOM) {
+			xlnx_pl_disp->fid = 1;
+		} else {
+			/*
+			 * FIXME: for interlace mode, application may send
+			 * dummy packets before the video field, need to set
+			 * the fid correctly to avoid display distortion
+			 */
+			xlnx_pl_disp->fid = 0;
+		}
+
+		xilinx_xdma_set_fid(xlnx_dma_chan->dma_chan, desc,
+				    xlnx_pl_disp->fid);
+	}
+
+	dmaengine_submit(desc);
+	dma_async_issue_pending(xlnx_dma_chan->dma_chan);
+}
+
+static void xlnx_pl_disp_plane_atomic_disable(struct drm_plane *plane,
+					      struct drm_atomic_state *state)
+{
+	xlnx_pl_disp_plane_disable(plane);
+}
+
+static int xlnx_pl_disp_plane_mode_set(struct drm_plane *plane,
+				       struct drm_framebuffer *fb,
+				       int crtc_x, int crtc_y,
+				       unsigned int crtc_w, unsigned int crtc_h,
+				       u32 src_x, uint32_t src_y,
+				       u32 src_w, uint32_t src_h)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = plane_to_dma(plane);
+	const struct drm_format_info *info = fb->format;
+	dma_addr_t luma_paddr, chroma_paddr;
+	size_t stride;
+	struct xlnx_dma_chan *xlnx_dma_chan = xlnx_pl_disp->chan;
+
+	if (info->num_planes > XLNX_PL_DISP_MAX_NUM_PLANES) {
+		dev_err(xlnx_pl_disp->dev, "Color format not supported\n");
+		return -EINVAL;
+	}
+	luma_paddr = drm_fb_cma_get_gem_addr(fb, plane->state, 0);
+	if (!luma_paddr) {
+		dev_err(xlnx_pl_disp->dev, "failed to get luma paddr\n");
+		return -EINVAL;
+	}
+
+	dev_dbg(xlnx_pl_disp->dev, "num planes = %d\n", info->num_planes);
+	xlnx_dma_chan->xt.numf = src_h;
+	xlnx_dma_chan->sgl[0].size = drm_format_plane_width_bytes(info,
+								  0, src_w);
+	xlnx_dma_chan->sgl[0].icg = fb->pitches[0] - xlnx_dma_chan->sgl[0].size;
+	xlnx_dma_chan->xt.src_start = luma_paddr;
+	xlnx_dma_chan->xt.frame_size = info->num_planes;
+	xlnx_dma_chan->xt.dir = DMA_MEM_TO_DEV;
+	xlnx_dma_chan->xt.src_sgl = true;
+	xlnx_dma_chan->xt.dst_sgl = false;
+
+	/* Do we have a video format aware dma channel?
+	 * so, modify descriptor accordingly. Hueristic test:
+	 * we have a multi-plane format but only one dma channel
+	 */
+	if (info->num_planes > 1) {
+		chroma_paddr = drm_fb_cma_get_gem_addr(fb, plane->state, 1);
+		if (!chroma_paddr) {
+			dev_err(xlnx_pl_disp->dev,
+				"failed to get chroma paddr\n");
+			return -EINVAL;
+		}
+		stride = xlnx_dma_chan->sgl[0].size +
+			xlnx_dma_chan->sgl[0].icg;
+		xlnx_dma_chan->sgl[0].src_icg = chroma_paddr -
+			xlnx_dma_chan->xt.src_start -
+			(xlnx_dma_chan->xt.numf * stride);
+	}
+
+	return 0;
+}
+
+static void xlnx_pl_disp_plane_atomic_update(struct drm_plane *plane,
+					     struct drm_atomic_state *state)
+{
+	int ret;
+	struct xlnx_pl_disp *xlnx_pl_disp = plane_to_dma(plane);
+
+	ret = xlnx_pl_disp_plane_mode_set(plane,
+					  plane->state->fb,
+					  plane->state->crtc_x,
+					  plane->state->crtc_y,
+					  plane->state->crtc_w,
+					  plane->state->crtc_h,
+					  plane->state->src_x >> 16,
+					  plane->state->src_y >> 16,
+					  plane->state->src_w >> 16,
+					  plane->state->src_h >> 16);
+	if (ret) {
+		dev_err(xlnx_pl_disp->dev, "failed to mode set a plane\n");
+		return;
+	}
+	/* in case frame buffer is used set the color format */
+	xilinx_xdma_drm_config(xlnx_pl_disp->chan->dma_chan,
+			       xlnx_pl_disp->plane.state->fb->format->format);
+	/* apply the new fb addr and enable */
+	xlnx_pl_disp_plane_enable(plane);
+}
+
+static int
+xlnx_pl_disp_plane_atomic_check(struct drm_plane *plane,
+				struct drm_atomic_state *state)
+{
+	struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
+	const struct drm_plane_state *old_plane_state =
+		drm_atomic_get_old_plane_state(state, plane);
+	struct drm_crtc *crtc = new_plane_state->crtc ?: old_plane_state->crtc;
+	struct drm_crtc_state *new_crtc_state;
+
+	if (!crtc)
+		return 0;
+
+	new_crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
+
+	/* plane must be enabled when state is active */
+	if (new_crtc_state->active && !new_plane_state->crtc)
+		return -EINVAL;
+
+	/*
+	 * This check is required to call modeset if there is a change in color
+	 * format
+	 */
+	if (new_plane_state->fb && old_plane_state->fb &&
+	    new_plane_state->fb->format->format !=
+	    old_plane_state->fb->format->format)
+		new_crtc_state->mode_changed = true;
+
+	return 0;
+}
+
+static int
+xlnx_pl_disp_plane_atomic_get_property(struct drm_plane *plane,
+				       const struct drm_plane_state *state,
+				       struct drm_property *property,
+				       uint64_t *val)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = plane_to_dma(plane);
+
+	if (property == xlnx_pl_disp->fid_err_prop)
+		*val = xlnx_pl_disp->fid_err_val;
+	else if (property == xlnx_pl_disp->fid_out_prop)
+		*val = xlnx_pl_disp->fid_out_val;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct drm_plane_helper_funcs xlnx_pl_disp_plane_helper_funcs = {
+	.atomic_update = xlnx_pl_disp_plane_atomic_update,
+	.atomic_disable = xlnx_pl_disp_plane_atomic_disable,
+	.atomic_check = xlnx_pl_disp_plane_atomic_check,
+};
+
+static struct drm_plane_funcs xlnx_pl_disp_plane_funcs = {
+	.update_plane = drm_atomic_helper_update_plane,
+	.disable_plane = drm_atomic_helper_disable_plane,
+	.destroy = drm_plane_cleanup,
+	.reset = drm_atomic_helper_plane_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_plane_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
+	.atomic_get_property = xlnx_pl_disp_plane_atomic_get_property,
+};
+
+static inline struct xlnx_pl_disp *drm_crtc_to_dma(struct drm_crtc *crtc)
+{
+	struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+
+	return crtc_to_dma(xlnx_crtc);
+}
+
+static void xlnx_pl_disp_crtc_atomic_begin(struct drm_crtc *crtc,
+					   struct drm_atomic_state *state)
+{
+	drm_crtc_vblank_on(crtc);
+	spin_lock_irq(&crtc->dev->event_lock);
+	if (crtc->state->event) {
+		/* Consume the flip_done event from atomic helper */
+		crtc->state->event->pipe = drm_crtc_index(crtc);
+		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
+		drm_crtc_arm_vblank_event(crtc, crtc->state->event);
+		crtc->state->event = NULL;
+	}
+	spin_unlock_irq(&crtc->dev->event_lock);
+}
+
+static void xlnx_pl_disp_clear_event(struct drm_crtc *crtc)
+{
+	if (crtc->state->event) {
+		complete_all(crtc->state->event->base.completion);
+		crtc->state->event = NULL;
+	}
+}
+
+static void xlnx_pl_disp_crtc_atomic_enable(struct drm_crtc *crtc,
+					    struct drm_atomic_state *state)
+{
+	struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode;
+	int vrefresh;
+	struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+	struct xlnx_pl_disp *xlnx_pl_disp = crtc_to_dma(xlnx_crtc);
+	struct videomode vm;
+
+	if (xlnx_pl_disp->vtc_bridge) {
+		/* set video timing */
+		drm_display_mode_to_videomode(adjusted_mode, &vm);
+		xlnx_bridge_set_timing(xlnx_pl_disp->vtc_bridge, &vm);
+		xlnx_bridge_enable(xlnx_pl_disp->vtc_bridge);
+	}
+
+	xlnx_pl_disp_plane_enable(crtc->primary);
+
+	/* Delay of 1 vblank interval for timing gen to be stable */
+	vrefresh = (adjusted_mode->clock * 1000) /
+		   (adjusted_mode->vtotal * adjusted_mode->htotal);
+	msleep(1 * 1000 / vrefresh);
+}
+
+static void xlnx_pl_disp_crtc_atomic_disable(struct drm_crtc *crtc,
+					     struct drm_atomic_state *state)
+{
+	struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+	struct xlnx_pl_disp *xlnx_pl_disp = crtc_to_dma(xlnx_crtc);
+
+	xlnx_pl_disp_plane_disable(crtc->primary);
+	xlnx_pl_disp_clear_event(crtc);
+	drm_crtc_vblank_off(crtc);
+	if (xlnx_pl_disp->vtc_bridge)
+		xlnx_bridge_disable(xlnx_pl_disp->vtc_bridge);
+}
+
+static int xlnx_pl_disp_crtc_atomic_check(struct drm_crtc *crtc,
+					  struct drm_atomic_state *state)
+{
+	return drm_atomic_add_affected_planes(state, crtc);
+}
+
+static struct drm_crtc_helper_funcs xlnx_pl_disp_crtc_helper_funcs = {
+	.atomic_enable = xlnx_pl_disp_crtc_atomic_enable,
+	.atomic_disable = xlnx_pl_disp_crtc_atomic_disable,
+	.atomic_check = xlnx_pl_disp_crtc_atomic_check,
+	.atomic_begin = xlnx_pl_disp_crtc_atomic_begin,
+};
+
+static void xlnx_pl_disp_crtc_destroy(struct drm_crtc *crtc)
+{
+	xlnx_pl_disp_plane_disable(crtc->primary);
+	drm_crtc_cleanup(crtc);
+}
+
+static int xlnx_pl_disp_crtc_enable_vblank(struct drm_crtc *crtc)
+{
+	struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+	struct xlnx_pl_disp *xlnx_pl_disp = crtc_to_dma(xlnx_crtc);
+
+	/*
+	 * Use the complete callback for vblank event assuming the dma engine
+	 * starts on the next descriptor upon this event. This may not be safe
+	 * assumption for some dma engines.
+	 */
+	xlnx_pl_disp->callback = xlnx_pl_disp_complete;
+	xlnx_pl_disp->callback_param = xlnx_pl_disp;
+
+	return 0;
+}
+
+static void xlnx_pl_disp_crtc_disable_vblank(struct drm_crtc *crtc)
+{
+	struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+	struct xlnx_pl_disp *xlnx_pl_disp = crtc_to_dma(xlnx_crtc);
+
+	xlnx_pl_disp->callback = NULL;
+	xlnx_pl_disp->callback_param = NULL;
+}
+
+static struct drm_crtc_funcs xlnx_pl_disp_crtc_funcs = {
+	.destroy = xlnx_pl_disp_crtc_destroy,
+	.set_config = drm_atomic_helper_set_config,
+	.page_flip = drm_atomic_helper_page_flip,
+	.reset = drm_atomic_helper_crtc_reset,
+	.atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
+	.enable_vblank = xlnx_pl_disp_crtc_enable_vblank,
+	.disable_vblank = xlnx_pl_disp_crtc_disable_vblank,
+};
+
+static int xlnx_pl_disp_bind(struct device *dev, struct device *master,
+			     void *data)
+{
+	struct drm_device *drm = data;
+	struct xlnx_pl_disp *xlnx_pl_disp = dev_get_drvdata(dev);
+	struct drm_mode_object *obj = &xlnx_pl_disp->plane.base;
+	int ret;
+	u32 *fmts = NULL;
+	unsigned int num_fmts = 0;
+
+	/* in case of fb IP query the supported formats and there count */
+	xilinx_xdma_get_drm_vid_fmts(xlnx_pl_disp->chan->dma_chan,
+				     &num_fmts, &fmts);
+	ret = drm_universal_plane_init(drm, &xlnx_pl_disp->plane, 0,
+				       &xlnx_pl_disp_plane_funcs,
+				       fmts ? fmts : &xlnx_pl_disp->fmt,
+				       num_fmts ? num_fmts : 1,
+				       NULL, DRM_PLANE_TYPE_PRIMARY, NULL);
+	if (ret)
+		return ret;
+
+	drm_plane_helper_add(&xlnx_pl_disp->plane,
+			     &xlnx_pl_disp_plane_helper_funcs);
+
+	ret = drm_crtc_init_with_planes(drm, &xlnx_pl_disp->xlnx_crtc.crtc,
+					&xlnx_pl_disp->plane, NULL,
+					&xlnx_pl_disp_crtc_funcs, NULL);
+	if (ret) {
+		drm_plane_cleanup(&xlnx_pl_disp->plane);
+		return ret;
+	}
+
+	drm_crtc_helper_add(&xlnx_pl_disp->xlnx_crtc.crtc,
+			    &xlnx_pl_disp_crtc_helper_funcs);
+	xlnx_pl_disp->xlnx_crtc.get_format = &xlnx_pl_disp_get_format;
+	xlnx_pl_disp->xlnx_crtc.get_align = &xlnx_pl_disp_get_align;
+	xlnx_pl_disp->drm = drm;
+
+	xlnx_pl_disp->fid_err_prop = drm_property_create_bool(xlnx_pl_disp->drm,
+							      0, "fid_err");
+	xlnx_pl_disp->fid_out_prop = drm_property_create_bool(xlnx_pl_disp->drm,
+							      0, "fid_out");
+	drm_object_attach_property(obj, xlnx_pl_disp->fid_err_prop, 0);
+	drm_object_attach_property(obj, xlnx_pl_disp->fid_out_prop, 0);
+
+	xlnx_crtc_register(xlnx_pl_disp->drm, &xlnx_pl_disp->xlnx_crtc);
+
+	return 0;
+}
+
+static void xlnx_pl_disp_unbind(struct device *dev, struct device *master,
+				void *data)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = dev_get_drvdata(dev);
+
+	drm_property_destroy(xlnx_pl_disp->drm, xlnx_pl_disp->fid_out_prop);
+	drm_property_destroy(xlnx_pl_disp->drm, xlnx_pl_disp->fid_err_prop);
+	xlnx_crtc_unregister(xlnx_pl_disp->drm, &xlnx_pl_disp->xlnx_crtc);
+	drm_plane_cleanup(&xlnx_pl_disp->plane);
+	drm_crtc_cleanup(&xlnx_pl_disp->xlnx_crtc.crtc);
+}
+
+static const struct component_ops xlnx_pl_disp_component_ops = {
+	.bind	= xlnx_pl_disp_bind,
+	.unbind	= xlnx_pl_disp_unbind,
+};
+
+static int xlnx_pl_disp_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *vtc_node;
+	struct xlnx_pl_disp *xlnx_pl_disp;
+	int ret;
+	const char *vformat;
+	struct dma_chan *dma_chan;
+	struct xlnx_dma_chan *xlnx_dma_chan;
+
+	xlnx_pl_disp = devm_kzalloc(dev, sizeof(*xlnx_pl_disp), GFP_KERNEL);
+	if (!xlnx_pl_disp)
+		return -ENOMEM;
+
+	dma_chan = of_dma_request_slave_channel(dev->of_node, "dma0");
+	if (IS_ERR_OR_NULL(dma_chan)) {
+		dev_err(dev, "failed to request dma channel\n");
+		return PTR_ERR(dma_chan);
+	}
+
+	xlnx_dma_chan = devm_kzalloc(dev, sizeof(*xlnx_dma_chan), GFP_KERNEL);
+	if (!xlnx_dma_chan)
+		return -ENOMEM;
+
+	xlnx_dma_chan->dma_chan = dma_chan;
+	xlnx_pl_disp->chan = xlnx_dma_chan;
+	ret = of_property_read_string(dev->of_node, "xlnx,vformat", &vformat);
+	if (ret) {
+		dev_err(dev, "No xlnx,vformat value in dts\n");
+		goto err_dma;
+	}
+
+	strcpy((char *)&xlnx_pl_disp->fmt, vformat);
+
+	/* VTC Bridge support */
+	vtc_node = of_parse_phandle(dev->of_node, "xlnx,bridge", 0);
+	if (vtc_node) {
+		xlnx_pl_disp->vtc_bridge = of_xlnx_bridge_get(vtc_node);
+		if (!xlnx_pl_disp->vtc_bridge) {
+			dev_info(dev, "Didn't get vtc bridge instance\n");
+			ret = -EPROBE_DEFER;
+			goto err_dma;
+		}
+	} else {
+		dev_info(dev, "vtc bridge property not present\n");
+	}
+
+	xlnx_pl_disp->dev = dev;
+	platform_set_drvdata(pdev, xlnx_pl_disp);
+
+	ret = component_add(dev, &xlnx_pl_disp_component_ops);
+	if (ret)
+		goto err_dma;
+
+	xlnx_pl_disp->master = xlnx_drm_pipeline_init(pdev);
+	if (IS_ERR(xlnx_pl_disp->master)) {
+		ret = PTR_ERR(xlnx_pl_disp->master);
+		dev_err(dev, "failed to initialize the drm pipeline\n");
+		goto err_component;
+	}
+
+	dev_info(&pdev->dev, "Xlnx PL display driver probed\n");
+
+	return 0;
+
+err_component:
+	component_del(dev, &xlnx_pl_disp_component_ops);
+err_dma:
+	dma_release_channel(xlnx_pl_disp->chan->dma_chan);
+
+	return ret;
+}
+
+static int xlnx_pl_disp_remove(struct platform_device *pdev)
+{
+	struct xlnx_pl_disp *xlnx_pl_disp = platform_get_drvdata(pdev);
+	struct xlnx_dma_chan *xlnx_dma_chan = xlnx_pl_disp->chan;
+
+	if (xlnx_pl_disp->vtc_bridge)
+		of_xlnx_bridge_put(xlnx_pl_disp->vtc_bridge);
+	xlnx_drm_pipeline_exit(xlnx_pl_disp->master);
+	component_del(&pdev->dev, &xlnx_pl_disp_component_ops);
+
+	/* Make sure the channel is terminated before release */
+	dmaengine_terminate_sync(xlnx_dma_chan->dma_chan);
+	dma_release_channel(xlnx_dma_chan->dma_chan);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_pl_disp_of_match[] = {
+	{ .compatible = "xlnx,pl-disp"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xlnx_pl_disp_of_match);
+
+static struct platform_driver xlnx_pl_disp_driver = {
+	.probe = xlnx_pl_disp_probe,
+	.remove = xlnx_pl_disp_remove,
+	.driver = {
+		.name = "xlnx-pl-disp",
+		.of_match_table = xlnx_pl_disp_of_match,
+	},
+};
+
+module_platform_driver(xlnx_pl_disp_driver);
+
+MODULE_AUTHOR("Saurabh Sengar");
+MODULE_DESCRIPTION("Xilinx DRM Display Driver for PL IPs");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_scaler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_scaler.c
@@ -0,0 +1,1980 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * VPSS SCALER DRM bridge driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Venkateshwar rao G <vgannava@xilinx.com>
+ *	   Rohit Athavale <rathavale@xilinx.com>
+ */
+
+/*
+ * Overview:
+ * This experimentatl driver works as a bridge driver and
+ * reused the code from V4L2.
+ * TODO:
+ * Need to implement in a modular approach to share driver code between
+ * V4L2 and DRM frameworks.
+ * Should be integrated with plane.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <uapi/linux/media-bus-format.h>
+
+#include "xlnx_bridge.h"
+
+#define XSCALER_MAX_WIDTH		(3840)
+#define XSCALER_MAX_HEIGHT		(2160)
+#define XSCALER_MAX_PHASES		(64)
+#define XSCALER_MIN_WIDTH		(64)
+#define XSCALER_MIN_HEIGHT		(64)
+
+/* Video subsytems block offset */
+#define S_AXIS_RESET_OFF		(0x00010000)
+#define V_HSCALER_OFF			(0x00000000)
+#define V_VSCALER_OFF			(0x00020000)
+
+/* HW Reset Network GPIO Channel */
+#define XGPIO_CH_RESET_SEL		(1)
+#define XGPIO_RESET_MASK_VIDEO_IN	BIT(0)
+#define XGPIO_RESET_MASK_IP_AXIS	BIT(1)
+#define XGPIO_RESET_MASK_ALL_BLOCKS	(XGPIO_RESET_MASK_VIDEO_IN | \
+						XGPIO_RESET_MASK_IP_AXIS)
+#define XGPIO_DATA_OFFSET		(0x0)
+#define XGPIO_DATA2_OFFSET		(0x8)
+#define XGPIO_TRI2_OFFSET		(0xc)
+
+#define XGPIO_ISR_OFFSET		(0x120)
+#define XGPIO_IER_OFFSET		(0x128)
+#define XGPIO_CHAN_OFFSET		(8)
+#define STEP_PRECISION			(65536)
+
+/* SCALER POWER MACROS */
+#define XSCALER_RESET_ASSERT            (0x1)
+#define XSCALER_RESET_DEASSERT          (0x0)
+
+/* Video IP PPC */
+#define XSCALER_PPC_1			(1)
+#define XSCALER_PPC_2			(2)
+
+#define XV_HSCALER_MAX_H_TAPS		(12)
+#define XV_HSCALER_MAX_H_PHASES		(64)
+#define XV_HSCALER_MAX_LINE_WIDTH	(3840)
+#define XV_VSCALER_MAX_V_TAPS		(12)
+#define XV_VSCALER_MAX_V_PHASES		(64)
+
+#define XV_HSCALER_TAPS_2		(2)
+#define XV_HSCALER_TAPS_4		(4)
+#define XV_HSCALER_TAPS_6		(6)
+#define XV_HSCALER_TAPS_8		(8)
+#define XV_HSCALER_TAPS_10		(10)
+#define XV_HSCALER_TAPS_12		(12)
+#define XV_VSCALER_TAPS_2		(2)
+#define XV_VSCALER_TAPS_4		(4)
+#define XV_VSCALER_TAPS_6		(6)
+#define XV_VSCALER_TAPS_8		(8)
+#define XV_VSCALER_TAPS_10		(10)
+#define XV_VSCALER_TAPS_12		(12)
+
+/* Mask definitions for Low and high 16 bits in a 32 bit number */
+#define XHSC_MASK_LOW_16BITS		GENMASK(15, 0)
+#define XHSC_MASK_HIGH_16BITS		GENMASK(31, 16)
+#define XHSC_MASK_LOW_32BITS		GENMASK(31, 0)
+#define XHSC_STEP_PRECISION_SHIFT	(16)
+#define XHSC_HPHASE_SHIFT_BY_6		(6)
+#define XHSC_HPHASE_MULTIPLIER		(9)
+#define XSCALER_BITSHIFT_16		(16)
+
+/* Mask definitions for Low and high 16 bits in a 32 bit number */
+#define XVSC_MASK_LOW_16BITS		GENMASK(15, 0)
+#define XVSC_MASK_HIGH_16BITS		GENMASK(31, 16)
+
+/* Scaler AP Control Registers */
+#define XSCALER_START			BIT(0)
+#define XSCALER_AUTO_RESTART		BIT(7)
+#define XSCALER_STREAM_ON		(XSCALER_START | XSCALER_AUTO_RESTART)
+
+/* H-scaler registers */
+#define XV_HSCALER_CTRL_ADDR_AP_CTRL			(0x0000)
+#define XV_HSCALER_CTRL_ADDR_GIE			(0x0004)
+#define XV_HSCALER_CTRL_ADDR_IER			(0x0008)
+#define XV_HSCALER_CTRL_ADDR_ISR			(0x000c)
+#define XV_HSCALER_CTRL_ADDR_HWREG_HEIGHT_DATA		(0x0010)
+#define XV_HSCALER_CTRL_ADDR_HWREG_WIDTHIN_DATA		(0x0018)
+#define XV_HSCALER_CTRL_ADDR_HWREG_WIDTHOUT_DATA	(0x0020)
+#define XV_HSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA	(0x0028)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PIXELRATE_DATA	(0x0030)
+#define XV_HSCALER_CTRL_ADDR_HWREG_COLORMODEOUT_DATA	(0X0038)
+#define XV_HSCALER_CTRL_ADDR_HWREG_HFLTCOEFF_BASE	(0x0800)
+#define XV_HSCALER_CTRL_ADDR_HWREG_HFLTCOEFF_HIGH	(0x0bff)
+
+#define XV_HSCALER_CTRL_WIDTH_HWREG_HFLTCOEFF		(16)
+#define XV_HSCALER_CTRL_DEPTH_HWREG_HFLTCOEFF		(384)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PHASESH_V_BASE	(0x2000)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PHASESH_V_HIGH	(0x3fff)
+#define XV_HSCALER_CTRL_WIDTH_HWREG_PHASESH_V		(18)
+#define XV_HSCALER_CTRL_DEPTH_HWREG_PHASESH_V		(1920)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PHASEH_FIX		(0x4000)
+
+/* H-scaler masks */
+#define XV_HSCALER_PHASESH_V_OUTPUT_WR_EN		BIT(8)
+
+/* V-scaler registers */
+#define XV_VSCALER_CTRL_ADDR_AP_CTRL			(0x000)
+#define XV_VSCALER_CTRL_ADDR_GIE			(0x004)
+#define XV_VSCALER_CTRL_ADDR_IER			(0x008)
+#define XV_VSCALER_CTRL_ADDR_ISR			(0x00c)
+#define XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTIN_DATA	(0x010)
+#define XV_VSCALER_CTRL_ADDR_HWREG_WIDTH_DATA		(0x018)
+#define XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTOUT_DATA	(0x020)
+#define XV_VSCALER_CTRL_ADDR_HWREG_LINERATE_DATA	(0x028)
+#define XV_VSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA	(0x030)
+#define XV_VSCALER_CTRL_ADDR_HWREG_VFLTCOEFF_BASE	(0x800)
+#define XV_VSCALER_CTRL_ADDR_HWREG_VFLTCOEFF_HIGH	(0xbff)
+
+/* Coefficients for 6, 8, 10 and 12 tap filters */
+
+static const s16
+XV_lanczos2_taps6[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{   0,    0, 4096,    0,    0,   0, },
+	{   0,  -40, 4099,   42,    0,  -5, },
+	{  -1,  -77, 4097,   87,   -1,  -9, },
+	{  -2, -111, 4092,  134,   -2, -15, },
+	{  -4, -143, 4082,  184,   -4, -19, },
+	{  -6, -173, 4068,  237,   -7, -23, },
+	{  -8, -201, 4051,  292,  -10, -28, },
+	{ -11, -226, 4029,  350,  -13, -33, },
+	{ -14, -248, 4003,  411,  -18, -38, },
+	{ -17, -269, 3974,  474,  -23, -43, },
+	{ -21, -287, 3940,  539,  -28, -47, },
+	{ -24, -303, 3903,  608,  -34, -54, },
+	{ -28, -317, 3862,  678,  -41, -58, },
+	{ -32, -329, 3817,  751,  -49, -62, },
+	{ -37, -339, 3768,  826,  -57, -65, },
+	{ -41, -347, 3716,  903,  -65, -70, },
+	{ -45, -353, 3661,  982,  -75, -74, },
+	{ -50, -358, 3602, 1063,  -84, -77, },
+	{ -54, -361, 3539, 1146,  -95, -79, },
+	{ -58, -362, 3474, 1230, -106, -82, },
+	{ -62, -361, 3406, 1317, -117, -87, },
+	{ -66, -359, 3335, 1404, -128, -90, },
+	{ -70, -356, 3261, 1493, -140, -92, },
+	{ -74, -351, 3185, 1583, -153, -94, },
+	{ -77, -346, 3106, 1673, -165, -95, },
+	{ -81, -339, 3025, 1765, -178, -96, },
+	{ -84, -331, 2942, 1857, -191, -97, },
+	{ -87, -322, 2858, 1950, -204, -99, },
+	{ -89, -313, 2771, 2043, -217, -99, },
+	{ -92, -302, 2683, 2136, -230, -99, },
+	{ -94, -292, 2594, 2228, -243, -97, },
+	{ -95, -280, 2504, 2321, -256, -98, },
+	{ -97, -268, 2413, 2413, -268, -97, },
+	{ -97, -256, 2321, 2504, -280, -96, },
+	{ -98, -243, 2228, 2594, -292, -93, },
+	{ -98, -230, 2136, 2683, -302, -93, },
+	{ -98, -217, 2043, 2771, -313, -90, },
+	{ -98, -204, 1950, 2858, -322, -88, },
+	{ -97, -191, 1857, 2942, -331, -84, },
+	{ -96, -178, 1765, 3025, -339, -81, },
+	{ -95, -165, 1673, 3106, -346, -77, },
+	{ -93, -153, 1583, 3185, -351, -75, },
+	{ -91, -140, 1493, 3261, -356, -71, },
+	{ -89, -128, 1404, 3335, -359, -67, },
+	{ -86, -117, 1317, 3406, -361, -63, },
+	{ -83, -106, 1230, 3474, -362, -57, },
+	{ -80,  -95, 1146, 3539, -361, -53, },
+	{ -77,  -84, 1063, 3602, -358, -50, },
+	{ -73,  -75,  982, 3661, -353, -46, },
+	{ -69,  -65,  903, 3716, -347, -42, },
+	{ -65,  -57,  826, 3768, -339, -37, },
+	{ -61,  -49,  751, 3817, -329, -33, },
+	{ -57,  -41,  678, 3862, -317, -29, },
+	{ -52,  -34,  608, 3903, -303, -26, },
+	{ -47,  -28,  539, 3940, -287, -21, },
+	{ -43,  -23,  474, 3974, -269, -17, },
+	{ -38,  -18,  411, 4003, -248, -14, },
+	{ -33,  -13,  350, 4029, -226, -11, },
+	{ -28,  -10,  292, 4051, -201,  -8, },
+	{ -24,   -7,  237, 4068, -173,  -5, },
+	{ -19,   -4,  184, 4082, -143,  -4, },
+	{ -14,   -2,  134, 4092, -111,  -3, },
+	{  -9,   -1,   87, 4097,  -77,  -1, },
+	{  -5,    0,   42, 4099,  -40,   0, }
+};
+
+/* ScalingRatio = 1.25 */
+static const s16
+XV_fixedcoeff_taps6_SR1p2[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{ -102,  512, 3208,  512, -102,  68, },
+	{  -97,  471, 3209,  555, -107,  65, },
+	{  -92,  431, 3208,  599, -113,  63, },
+	{  -87,  392, 3205,  645, -118,  59, },
+	{  -82,  354, 3199,  691, -124,  58, },
+	{  -77,  318, 3191,  739, -130,  55, },
+	{  -72,  282, 3181,  788, -136,  53, },
+	{  -68,  248, 3169,  838, -141,  50, },
+	{  -64,  216, 3155,  889, -147,  47, },
+	{  -59,  184, 3139,  941, -153,  44, },
+	{  -55,  154, 3120,  993, -158,  42, },
+	{  -52,  125, 3100, 1047, -164,  40, },
+	{  -48,   98, 3077, 1101, -169,  37, },
+	{  -44,   71, 3052, 1157, -174,  34, },
+	{  -41,   46, 3025, 1212, -180,  34, },
+	{  -38,   23, 2996, 1269, -184,  30, },
+	{  -35,    0, 2965, 1326, -189,  29, },
+	{  -32,  -21, 2933, 1383, -193,  26, },
+	{  -29,  -41, 2898, 1441, -198,  25, },
+	{  -26,  -60, 2862, 1500, -201,  21, },
+	{  -24,  -78, 2823, 1558, -205,  22, },
+	{  -21,  -94, 2784, 1617, -208,  18, },
+	{  -19, -109, 2742, 1676, -210,  16, },
+	{  -17, -123, 2699, 1734, -212,  15, },
+	{  -14, -136, 2654, 1793, -214,  13, },
+	{  -12, -148, 2608, 1852, -214,  10, },
+	{  -10, -159, 2560, 1910, -215,  10, },
+	{   -9, -168, 2512, 1968, -215,   8, },
+	{   -7, -177, 2461, 2026, -214,   7, },
+	{   -5, -185, 2410, 2083, -212,   5, },
+	{   -3, -192, 2358, 2139, -209,   3, },
+	{   -2, -197, 2304, 2195, -206,   2, },
+	{    0, -202, 2250, 2250, -202,   0, },
+	{    2, -206, 2195, 2304, -197,  -2, },
+	{    3, -209, 2139, 2358, -192,  -3, },
+	{    5, -212, 2083, 2410, -185,  -5, },
+	{    6, -214, 2026, 2461, -177,  -6, },
+	{    8, -215, 1968, 2512, -168,  -9, },
+	{   10, -215, 1910, 2560, -159, -10, },
+	{   11, -214, 1852, 2608, -148, -13, },
+	{   13, -214, 1793, 2654, -136, -14, },
+	{   15, -212, 1734, 2699, -123, -17, },
+	{   17, -210, 1676, 2742, -109, -20, },
+	{   18, -208, 1617, 2784,  -94, -21, },
+	{   20, -205, 1558, 2823,  -78, -22, },
+	{   22, -201, 1500, 2862,  -60, -27, },
+	{   24, -198, 1441, 2898,  -41, -28, },
+	{   26, -193, 1383, 2933,  -21, -32, },
+	{   28, -189, 1326, 2965,    0, -34, },
+	{   30, -184, 1269, 2996,   23, -38, },
+	{   33, -180, 1212, 3025,   46, -40, },
+	{   35, -174, 1157, 3052,   71, -45, },
+	{   37, -169, 1101, 3077,   98, -48, },
+	{   40, -164, 1047, 3100,  125, -52, },
+	{   42, -158,  993, 3120,  154, -55, },
+	{   44, -153,  941, 3139,  184, -59, },
+	{   47, -147,  889, 3155,  216, -64, },
+	{   50, -141,  838, 3169,  248, -68, },
+	{   52, -136,  788, 3181,  282, -71, },
+	{   55, -130,  739, 3191,  318, -77, },
+	{   57, -124,  691, 3199,  354, -81, },
+	{   60, -118,  645, 3205,  392, -88, },
+	{   63, -113,  599, 3208,  431, -92, },
+	{   65, -107,  555, 3209,  471, -97, }
+};
+
+/* ScalingRatio = 2.0 */
+static const s16
+XV_fixedcoeff_taps6_SR2[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{   0, 970, 2235,  970,   0, -79, },
+	{  -3, 943, 2233,  997,   3, -77, },
+	{  -5, 915, 2231, 1025,   6, -76, },
+	{  -8, 888, 2227, 1052,  10, -73, },
+	{ -10, 861, 2223, 1079,  14, -71, },
+	{ -12, 834, 2218, 1107,  18, -69, },
+	{ -14, 808, 2213, 1134,  22, -67, },
+	{ -15, 782, 2206, 1162,  27, -66, },
+	{ -17, 756, 2199, 1189,  32, -63, },
+	{ -18, 731, 2191, 1217,  37, -62, },
+	{ -20, 706, 2182, 1245,  42, -59, },
+	{ -21, 681, 2172, 1272,  48, -56, },
+	{ -22, 657, 2162, 1300,  55, -56, },
+	{ -22, 633, 2151, 1327,  61, -54, },
+	{ -23, 609, 2139, 1355,  68, -52, },
+	{ -24, 586, 2126, 1382,  76, -50, },
+	{ -25, 564, 2113, 1410,  83, -49, },
+	{ -25, 541, 2099, 1437,  91, -47, },
+	{ -26, 520, 2084, 1464, 100, -46, },
+	{ -26, 498, 2069, 1491, 109, -45, },
+	{ -27, 477, 2053, 1517, 118, -42, },
+	{ -27, 457, 2036, 1544, 128, -42, },
+	{ -27, 437, 2019, 1570, 138, -41, },
+	{ -28, 418, 2001, 1596, 148, -39, },
+	{ -28, 399, 1983, 1622, 160, -40, },
+	{ -29, 380, 1964, 1647, 171, -37, },
+	{ -29, 362, 1944, 1672, 183, -36, },
+	{ -29, 345, 1924, 1697, 195, -36, },
+	{ -30, 328, 1903, 1722, 208, -35, },
+	{ -30, 311, 1882, 1746, 221, -34, },
+	{ -31, 295, 1860, 1770, 235, -33, },
+	{ -31, 279, 1838, 1793, 249, -32, },
+	{ -32, 264, 1816, 1816, 264, -32, },
+	{ -32, 249, 1793, 1838, 279, -31, },
+	{ -33, 235, 1770, 1860, 295, -31, },
+	{ -34, 221, 1746, 1882, 311, -30, },
+	{ -35, 208, 1722, 1903, 328, -30, },
+	{ -35, 195, 1697, 1924, 345, -30, },
+	{ -36, 183, 1672, 1944, 362, -29, },
+	{ -37, 171, 1647, 1964, 380, -29, },
+	{ -38, 160, 1622, 1983, 399, -30, },
+	{ -39, 148, 1596, 2001, 418, -28, },
+	{ -40, 138, 1570, 2019, 437, -28, },
+	{ -42, 128, 1544, 2036, 457, -27, },
+	{ -43, 118, 1517, 2053, 477, -26, },
+	{ -44, 109, 1491, 2069, 498, -27, },
+	{ -46, 100, 1464, 2084, 520, -26, },
+	{ -47,  91, 1437, 2099, 541, -25, },
+	{ -49,  83, 1410, 2113, 564, -25, },
+	{ -50,  76, 1382, 2126, 586, -24, },
+	{ -52,  68, 1355, 2139, 609, -23, },
+	{ -54,  61, 1327, 2151, 633, -22, },
+	{ -55,  55, 1300, 2162, 657, -23, },
+	{ -57,  48, 1272, 2172, 681, -20, },
+	{ -59,  42, 1245, 2182, 706, -20, },
+	{ -61,  37, 1217, 2191, 731, -19, },
+	{ -63,  32, 1189, 2199, 756, -17, },
+	{ -65,  27, 1162, 2206, 782, -16, },
+	{ -67,  22, 1134, 2213, 808, -14, },
+	{ -69,  18, 1107, 2218, 834, -12, },
+	{ -71,  14, 1079, 2223, 861, -10, },
+	{ -73,  10, 1052, 2227, 888,  -8, },
+	{ -75,   6, 1025, 2231, 915,  -6, },
+	{ -77,   3,  997, 2233, 943,  -3, }
+};
+
+/* ScalingRatio = 3.0 */
+static const s16
+XV_fixedcoeff_taps6_SR3[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{ 126, 1019, 1806, 1019,  126,   0, },
+	{ 120, 1000, 1805, 1038,  132,   1, },
+	{ 114,  980, 1804, 1057,  138,   3, },
+	{ 108,  961, 1802, 1075,  145,   5, },
+	{ 103,  942, 1800, 1094,  152,   5, },
+	{  98,  922, 1797, 1113,  159,   7, },
+	{  93,  903, 1794, 1131,  167,   8, },
+	{  88,  884, 1790, 1150,  174,  10, },
+	{  84,  865, 1786, 1168,  182,  11, },
+	{  80,  846, 1782, 1187,  191,  10, },
+	{  76,  827, 1777, 1205,  199,  12, },
+	{  72,  809, 1771, 1223,  208,  13, },
+	{  68,  790, 1766, 1241,  217,  14, },
+	{  65,  772, 1759, 1259,  226,  15, },
+	{  61,  753, 1753, 1277,  236,  16, },
+	{  58,  735, 1746, 1295,  246,  16, },
+	{  56,  717, 1738, 1313,  256,  16, },
+	{  53,  699, 1730, 1330,  266,  18, },
+	{  50,  682, 1722, 1347,  277,  18, },
+	{  48,  664, 1713, 1364,  288,  19, },
+	{  46,  647, 1704, 1381,  299,  19, },
+	{  43,  630, 1694, 1398,  311,  20, },
+	{  41,  613, 1684, 1414,  323,  21, },
+	{  40,  596, 1674, 1430,  335,  21, },
+	{  38,  580, 1663, 1446,  347,  22, },
+	{  36,  563, 1652, 1462,  360,  23, },
+	{  35,  547, 1641, 1478,  373,  22, },
+	{  33,  531, 1629, 1493,  386,  24, },
+	{  32,  516, 1617, 1508,  399,  24, },
+	{  31,  500, 1604, 1523,  413,  25, },
+	{  30,  485, 1592, 1537,  427,  25, },
+	{  29,  470, 1578, 1551,  441,  27, },
+	{  28,  455, 1565, 1565,  455,  28, },
+	{  27,  441, 1551, 1578,  470,  29, },
+	{  26,  427, 1537, 1592,  485,  29, },
+	{  25,  413, 1523, 1604,  500,  31, },
+	{  24,  399, 1508, 1617,  516,  32, },
+	{  24,  386, 1493, 1629,  531,  33, },
+	{  23,  373, 1478, 1641,  547,  34, },
+	{  22,  360, 1462, 1652,  563,  37, },
+	{  22,  347, 1446, 1663,  580,  38, },
+	{  21,  335, 1430, 1674,  596,  40, },
+	{  20,  323, 1414, 1684,  613,  42, },
+	{  20,  311, 1398, 1694,  630,  43, },
+	{  19,  299, 1381, 1704,  647,  46, },
+	{  19,  288, 1364, 1713,  664,  48, },
+	{  18,  277, 1347, 1722,  682,  50, },
+	{  17,  266, 1330, 1730,  699,  54, },
+	{  17,  256, 1313, 1738,  717,  55, },
+	{  16,  246, 1295, 1746,  735,  58, },
+	{  15,  236, 1277, 1753,  753,  62, },
+	{  15,  226, 1259, 1759,  772,  65, },
+	{  14,  217, 1241, 1766,  790,  68, },
+	{  13,  208, 1223, 1771,  809,  72, },
+	{  12,  199, 1205, 1777,  827,  76, },
+	{  11,  191, 1187, 1782,  846,  79, },
+	{  10,  182, 1168, 1786,  865,  85, },
+	{   9,  174, 1150, 1790,  884,  89, },
+	{   8,  167, 1131, 1794,  903,  93, },
+	{   7,  159, 1113, 1797,  922,  98, },
+	{   6,  152, 1094, 1800,  942, 102, },
+	{   5,  145, 1075, 1802,  961, 108, },
+	{   3,  138, 1057, 1804,  980, 114, },
+	{   2,  132, 1038, 1805, 1000, 119, }
+};
+
+/* ScalingRatio = 4 */
+static const s16
+XV_fixedcoeff_taps6_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{ 176, 1009, 1643, 1009, 176,  83, },
+	{ 169,  993, 1644, 1026, 183,  81, },
+	{ 162,  978, 1644, 1042, 190,  80, },
+	{ 156,  962, 1643, 1058, 198,  79, },
+	{ 150,  946, 1642, 1074, 205,  79, },
+	{ 144,  930, 1641, 1091, 213,  77, },
+	{ 138,  914, 1640, 1107, 222,  75, },
+	{ 133,  898, 1638, 1123, 230,  74, },
+	{ 128,  882, 1635, 1139, 239,  73, },
+	{ 123,  866, 1633, 1154, 248,  72, },
+	{ 118,  850, 1629, 1170, 257,  72, },
+	{ 114,  834, 1626, 1186, 267,  69, },
+	{ 109,  818, 1622, 1201, 276,  70, },
+	{ 105,  802, 1618, 1217, 286,  68, },
+	{ 101,  786, 1613, 1232, 297,  67, },
+	{  97,  771, 1608, 1247, 307,  66, },
+	{  94,  755, 1603, 1262, 318,  64, },
+	{  91,  739, 1597, 1276, 328,  65, },
+	{  87,  724, 1591, 1291, 339,  64, },
+	{  85,  708, 1585, 1305, 351,  62, },
+	{  82,  693, 1578, 1319, 362,  62, },
+	{  79,  677, 1571, 1333, 374,  62, },
+	{  77,  662, 1563, 1347, 386,  61, },
+	{  75,  647, 1556, 1360, 398,  60, },
+	{  73,  632, 1547, 1373, 410,  61, },
+	{  71,  617, 1539, 1386, 423,  60, },
+	{  69,  602, 1530, 1399, 436,  60, },
+	{  68,  587, 1521, 1412, 449,  59, },
+	{  66,  573, 1511, 1424, 462,  60, },
+	{  65,  558, 1501, 1436, 475,  61, },
+	{  64,  544, 1491, 1447, 488,  62, },
+	{  63,  530, 1481, 1459, 502,  61, },
+	{  62,  516, 1470, 1470, 516,  62, },
+	{  62,  502, 1459, 1481, 530,  62, },
+	{  61,  488, 1447, 1491, 544,  65, },
+	{  61,  475, 1436, 1501, 558,  65, },
+	{  60,  462, 1424, 1511, 573,  66, },
+	{  60,  449, 1412, 1521, 587,  67, },
+	{  60,  436, 1399, 1530, 602,  69, },
+	{  60,  423, 1386, 1539, 617,  71, },
+	{  61,  410, 1373, 1547, 632,  73, },
+	{  61,  398, 1360, 1556, 647,  74, },
+	{  61,  386, 1347, 1563, 662,  77, },
+	{  62,  374, 1333, 1571, 677,  79, },
+	{  62,  362, 1319, 1578, 693,  82, },
+	{  63,  351, 1305, 1585, 708,  84, },
+	{  64,  339, 1291, 1591, 724,  87, },
+	{  64,  328, 1276, 1597, 739,  92, },
+	{  65,  318, 1262, 1603, 755,  93, },
+	{  66,  307, 1247, 1608, 771,  97, },
+	{  67,  297, 1232, 1613, 786, 101, },
+	{  68,  286, 1217, 1618, 802, 105, },
+	{  69,  276, 1201, 1622, 818, 110, },
+	{  70,  267, 1186, 1626, 834, 113, },
+	{  71,  257, 1170, 1629, 850, 119, },
+	{  72,  248, 1154, 1633, 866, 123, },
+	{  73,  239, 1139, 1635, 882, 128, },
+	{  75,  230, 1123, 1638, 898, 132, },
+	{  76,  222, 1107, 1640, 914, 137, },
+	{  77,  213, 1091, 1641, 930, 144, },
+	{  78,  205, 1074, 1642, 946, 151, },
+	{  79,  198, 1058, 1643, 962, 156, },
+	{  80,  190, 1042, 1644, 978, 162, },
+	{  82,  183, 1026, 1644, 993, 168, }
+};
+
+/* ScalingRatio = 2.0 */
+static const s16
+XV_fixedcoeff_taps8_SR2[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_8] = {
+	{ -55,   0, 1078, 2049, 1078,    0, -55,   1, },
+	{ -53,  -7, 1055, 2049, 1102,    7, -56,  -1, },
+	{ -52, -13, 1032, 2048, 1126,   15, -58,  -2, },
+	{ -50, -20, 1009, 2047, 1149,   22, -59,  -2, },
+	{ -49, -26,  986, 2046, 1173,   31, -61,  -4, },
+	{ -47, -31,  963, 2043, 1197,   39, -62,  -6, },
+	{ -46, -37,  940, 2040, 1220,   48, -64,  -5, },
+	{ -45, -42,  917, 2037, 1244,   57, -65,  -7, },
+	{ -43, -47,  894, 2033, 1267,   66, -67,  -7, },
+	{ -42, -51,  871, 2028, 1290,   76, -69,  -7, },
+	{ -41, -55,  848, 2023, 1313,   86, -70,  -8, },
+	{ -40, -59,  826, 2017, 1336,   97, -72,  -9, },
+	{ -38, -63,  803, 2010, 1359,  108, -73, -10, },
+	{ -37, -67,  781, 2003, 1382,  119, -75, -10, },
+	{ -36, -70,  759, 1996, 1405,  130, -76, -12, },
+	{ -35, -73,  737, 1987, 1427,  142, -78, -11, },
+	{ -34, -76,  715, 1979, 1449,  154, -79, -12, },
+	{ -33, -78,  693, 1969, 1471,  167, -81, -12, },
+	{ -32, -81,  672, 1959, 1493,  180, -82, -13, },
+	{ -31, -83,  650, 1949, 1514,  193, -83, -13, },
+	{ -30, -85,  629, 1938, 1536,  207, -85, -14, },
+	{ -29, -86,  609, 1926, 1557,  221, -86, -16, },
+	{ -28, -88,  588, 1914, 1577,  235, -87, -15, },
+	{ -28, -89,  568, 1902, 1598,  250, -88, -17, },
+	{ -27, -90,  548, 1889, 1618,  265, -89, -18, },
+	{ -26, -91,  528, 1875, 1638,  280, -90, -18, },
+	{ -25, -92,  508, 1861, 1657,  296, -91, -18, },
+	{ -24, -93,  489, 1846, 1676,  312, -92, -18, },
+	{ -24, -93,  470, 1831, 1695,  328, -92, -19, },
+	{ -23, -94,  451, 1816, 1714,  345, -93, -20, },
+	{ -22, -94,  432, 1800, 1732,  361, -93, -20, },
+	{ -22, -94,  414, 1783, 1749,  379, -94, -19, },
+	{ -21, -94,  396, 1767, 1767,  396, -94, -21, },
+	{ -21, -94,  379, 1749, 1783,  414, -94, -20, },
+	{ -20, -93,  361, 1732, 1800,  432, -94, -22, },
+	{ -19, -93,  345, 1714, 1816,  451, -94, -24, },
+	{ -19, -92,  328, 1695, 1831,  470, -93, -24, },
+	{ -18, -92,  312, 1676, 1846,  489, -93, -24, },
+	{ -18, -91,  296, 1657, 1861,  508, -92, -25, },
+	{ -17, -90,  280, 1638, 1875,  528, -91, -27, },
+	{ -17, -89,  265, 1618, 1889,  548, -90, -28, },
+	{ -16, -88,  250, 1598, 1902,  568, -89, -29, },
+	{ -16, -87,  235, 1577, 1914,  588, -88, -27, },
+	{ -15, -86,  221, 1557, 1926,  609, -86, -30, },
+	{ -14, -85,  207, 1536, 1938,  629, -85, -30, },
+	{ -14, -83,  193, 1514, 1949,  650, -83, -30, },
+	{ -13, -82,  180, 1493, 1959,  672, -81, -32, },
+	{ -13, -81,  167, 1471, 1969,  693, -78, -32, },
+	{ -12, -79,  154, 1449, 1979,  715, -76, -34, },
+	{ -12, -78,  142, 1427, 1987,  737, -73, -34, },
+	{ -11, -76,  130, 1405, 1996,  759, -70, -37, },
+	{ -10, -75,  119, 1382, 2003,  781, -67, -37, },
+	{ -10, -73,  108, 1359, 2010,  803, -63, -38, },
+	{  -9, -72,   97, 1336, 2017,  826, -59, -40, },
+	{  -8, -70,   86, 1313, 2023,  848, -55, -41, },
+	{  -8, -69,   76, 1290, 2028,  871, -51, -41, },
+	{  -7, -67,   66, 1267, 2033,  894, -47, -43, },
+	{  -6, -65,   57, 1244, 2037,  917, -42, -46, },
+	{  -5, -64,   48, 1220, 2040,  940, -37, -46, },
+	{  -5, -62,   39, 1197, 2043,  963, -31, -48, },
+	{  -4, -61,   31, 1173, 2046,  986, -26, -49, },
+	{  -3, -59,   22, 1149, 2047, 1009, -20, -49, },
+	{  -2, -58,   15, 1126, 2048, 1032, -13, -52, },
+	{  -1, -56,    7, 1102, 2049, 1055,  -7, -53, }
+};
+
+/* ScalingRatio = 3.0 */
+static const s16
+XV_fixedcoeff_taps8_SR3[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_8] = {
+	{   0, 275, 1036, 1514, 1036,  275,   0, -40, },
+	{  -1, 266, 1023, 1514, 1048,  283,   1, -38, },
+	{  -2, 257, 1010, 1513, 1060,  292,   2, -36, },
+	{  -3, 249,  997, 1512, 1073,  301,   3, -36, },
+	{  -3, 241,  983, 1510, 1085,  310,   5, -35, },
+	{  -4, 233,  970, 1509, 1097,  319,   6, -34, },
+	{  -5, 225,  957, 1507, 1109,  329,   7, -33, },
+	{  -6, 217,  944, 1505, 1121,  338,   9, -32, },
+	{  -6, 210,  931, 1503, 1133,  348,  10, -33, },
+	{  -7, 202,  917, 1500, 1144,  358,  12, -30, },
+	{  -7, 195,  904, 1497, 1156,  368,  13, -30, },
+	{  -8, 188,  891, 1494, 1167,  378,  15, -29, },
+	{  -9, 181,  877, 1491, 1179,  388,  17, -28, },
+	{  -9, 174,  864, 1487, 1190,  398,  19, -27, },
+	{  -9, 168,  851, 1483, 1201,  409,  21, -28, },
+	{ -10, 161,  837, 1479, 1212,  419,  23, -25, },
+	{ -10, 155,  824, 1475, 1223,  430,  25, -26, },
+	{ -11, 149,  811, 1470, 1233,  441,  27, -24, },
+	{ -11, 142,  798, 1465, 1244,  452,  29, -23, },
+	{ -12, 137,  784, 1460, 1254,  463,  32, -22, },
+	{ -12, 131,  771, 1455, 1264,  474,  34, -21, },
+	{ -12, 125,  758, 1449, 1275,  486,  37, -22, },
+	{ -13, 120,  745, 1444, 1284,  497,  40, -21, },
+	{ -13, 115,  732, 1438, 1294,  509,  42, -21, },
+	{ -13, 109,  719, 1432, 1304,  520,  45, -20, },
+	{ -14, 104,  706, 1425, 1313,  532,  48, -18, },
+	{ -14, 100,  693, 1418, 1322,  544,  52, -19, },
+	{ -14,  95,  680, 1412, 1332,  556,  55, -20, },
+	{ -15,  90,  667, 1404, 1340,  568,  58, -16, },
+	{ -15,  86,  655, 1397, 1349,  580,  62, -18, },
+	{ -16,  82,  642, 1390, 1358,  592,  66, -18, },
+	{ -16,  77,  630, 1382, 1366,  605,  69, -17, },
+	{ -16,  73,  617, 1374, 1374,  617,  73, -16, },
+	{ -17,  69,  605, 1366, 1382,  630,  77, -16, },
+	{ -17,  66,  592, 1358, 1390,  642,  82, -17, },
+	{ -18,  62,  580, 1349, 1397,  655,  86, -15, },
+	{ -18,  58,  568, 1340, 1404,  667,  90, -13, },
+	{ -18,  55,  556, 1332, 1412,  680,  95, -16, },
+	{ -19,  52,  544, 1322, 1418,  693, 100, -14, },
+	{ -19,  48,  532, 1313, 1425,  706, 104, -13, },
+	{ -20,  45,  520, 1304, 1432,  719, 109, -13, },
+	{ -20,  42,  509, 1294, 1438,  732, 115, -14, },
+	{ -21,  40,  497, 1284, 1444,  745, 120, -13, },
+	{ -22,  37,  486, 1275, 1449,  758, 125, -12, },
+	{ -22,  34,  474, 1264, 1455,  771, 131, -11, },
+	{ -23,  32,  463, 1254, 1460,  784, 137, -11, },
+	{ -23,  29,  452, 1244, 1465,  798, 142, -11, },
+	{ -24,  27,  441, 1233, 1470,  811, 149, -11, },
+	{ -25,  25,  430, 1223, 1475,  824, 155, -11, },
+	{ -26,  23,  419, 1212, 1479,  837, 161,  -9, },
+	{ -26,  21,  409, 1201, 1483,  851, 168, -11, },
+	{ -27,  19,  398, 1190, 1487,  864, 174,  -9, },
+	{ -28,  17,  388, 1179, 1491,  877, 181,  -9, },
+	{ -29,  15,  378, 1167, 1494,  891, 188,  -8, },
+	{ -29,  13,  368, 1156, 1497,  904, 195,  -8, },
+	{ -30,  12,  358, 1144, 1500,  917, 202,  -7, },
+	{ -31,  10,  348, 1133, 1503,  931, 210,  -8, },
+	{ -32,   9,  338, 1121, 1505,  944, 217,  -6, },
+	{ -33,   7,  329, 1109, 1507,  957, 225,  -5, },
+	{ -34,   6,  319, 1097, 1509,  970, 233,  -4, },
+	{ -35,   5,  310, 1085, 1510,  983, 241,  -3, },
+	{ -36,   3,  301, 1073, 1512,  997, 249,  -3, },
+	{ -37,   2,  292, 1060, 1513, 1010, 257,  -1, },
+	{ -38,   1,  283, 1048, 1514, 1023, 266,  -1, }
+};
+
+/* ScalingRatio = 4 */
+static const s16
+XV_fixedcoeff_taps8_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_8] = {
+	{ 49, 366, 977, 1312,  977, 366,  49,  0, },
+	{ 48, 357, 967, 1312,  986, 374,  51,  1, },
+	{ 46, 349, 958, 1311,  995, 382,  54,  1, },
+	{ 44, 342, 948, 1311, 1004, 390,  56,  1, },
+	{ 42, 334, 939, 1310, 1013, 399,  58,  1, },
+	{ 40, 326, 929, 1309, 1021, 407,  60,  4, },
+	{ 39, 318, 919, 1308, 1030, 415,  63,  4, },
+	{ 37, 311, 910, 1307, 1039, 424,  65,  3, },
+	{ 36, 303, 900, 1305, 1047, 433,  68,  4, },
+	{ 34, 296, 890, 1303, 1055, 442,  70,  6, },
+	{ 33, 289, 880, 1301, 1064, 450,  73,  6, },
+	{ 32, 282, 870, 1299, 1072, 459,  76,  6, },
+	{ 31, 275, 861, 1297, 1080, 468,  79,  5, },
+	{ 29, 268, 851, 1295, 1088, 477,  82,  6, },
+	{ 28, 261, 841, 1292, 1096, 486,  85,  7, },
+	{ 27, 254, 831, 1289, 1104, 496,  88,  7, },
+	{ 26, 248, 821, 1287, 1112, 505,  91,  6, },
+	{ 25, 241, 811, 1284, 1119, 514,  94,  8, },
+	{ 24, 235, 800, 1280, 1127, 523,  98,  9, },
+	{ 23, 228, 790, 1277, 1134, 533, 101, 10, },
+	{ 22, 222, 780, 1273, 1141, 542, 105, 11, },
+	{ 22, 216, 770, 1270, 1148, 552, 109,  9, },
+	{ 21, 210, 760, 1266, 1155, 561, 112, 11, },
+	{ 20, 204, 750, 1262, 1162, 571, 116, 11, },
+	{ 19, 198, 740, 1257, 1169, 581, 120, 12, },
+	{ 19, 193, 730, 1253, 1175, 590, 124, 12, },
+	{ 18, 187, 720, 1248, 1182, 600, 129, 12, },
+	{ 17, 182, 710, 1244, 1188, 610, 133, 12, },
+	{ 17, 176, 700, 1239, 1194, 620, 137, 13, },
+	{ 16, 171, 690, 1234, 1201, 630, 142, 12, },
+	{ 16, 166, 680, 1229, 1206, 640, 146, 13, },
+	{ 15, 161, 670, 1223, 1212, 650, 151, 14, },
+	{ 15, 156, 660, 1218, 1218, 660, 156, 13, },
+	{ 14, 151, 650, 1212, 1223, 670, 161, 15, },
+	{ 14, 146, 640, 1206, 1229, 680, 166, 15, },
+	{ 13, 142, 630, 1201, 1234, 690, 171, 15, },
+	{ 13, 137, 620, 1194, 1239, 700, 176, 17, },
+	{ 12, 133, 610, 1188, 1244, 710, 182, 17, },
+	{ 12, 129, 600, 1182, 1248, 720, 187, 18, },
+	{ 11, 124, 590, 1175, 1253, 730, 193, 20, },
+	{ 11, 120, 581, 1169, 1257, 740, 198, 20, },
+	{ 11, 116, 571, 1162, 1262, 750, 204, 20, },
+	{ 10, 112, 561, 1155, 1266, 760, 210, 22, },
+	{ 10, 109, 552, 1148, 1270, 770, 216, 21, },
+	{ 10, 105, 542, 1141, 1273, 780, 222, 23, },
+	{  9, 101, 533, 1134, 1277, 790, 228, 24, },
+	{  9,  98, 523, 1127, 1280, 800, 235, 24, },
+	{  8,  94, 514, 1119, 1284, 811, 241, 25, },
+	{  8,  91, 505, 1112, 1287, 821, 248, 24, },
+	{  8,  88, 496, 1104, 1289, 831, 254, 26, },
+	{  7,  85, 486, 1096, 1292, 841, 261, 28, },
+	{  7,  82, 477, 1088, 1295, 851, 268, 28, },
+	{  6,  79, 468, 1080, 1297, 861, 275, 30, },
+	{  6,  76, 459, 1072, 1299, 870, 282, 32, },
+	{  5,  73, 450, 1064, 1301, 880, 289, 34, },
+	{  5,  70, 442, 1055, 1303, 890, 296, 35, },
+	{  4,  68, 433, 1047, 1305, 900, 303, 36, },
+	{  4,  65, 424, 1039, 1307, 910, 311, 36, },
+	{  3,  63, 415, 1030, 1308, 919, 318, 40, },
+	{  3,  60, 407, 1021, 1309, 929, 326, 41, },
+	{  2,  58, 399, 1013, 1310, 939, 334, 41, },
+	{  2,  56, 390, 1004, 1311, 948, 342, 43, },
+	{  1,  54, 382,  995, 1311, 958, 349, 46, },
+	{  1,  51, 374,  986, 1312, 967, 357, 48, }
+};
+
+/* ScalingRatio = 3.0 */
+static const s16
+XV_fixedcoeff_taps10_SR3[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_10] = {
+	{ -31,   0, 359, 1033, 1399, 1033,  359,   0, -31, -25, },
+	{ -31,  -2, 350, 1022, 1398, 1043,  368,   3, -31, -24, },
+	{ -30,  -4, 341, 1012, 1398, 1053,  378,   5, -32, -25, },
+	{ -30,  -6, 333, 1002, 1398, 1062,  387,   8, -32, -26, },
+	{ -30,  -8, 324,  992, 1397, 1072,  396,  10, -32, -25, },
+	{ -30, -10, 315,  981, 1396, 1082,  406,  13, -33, -24, },
+	{ -29, -12, 307,  971, 1395, 1091,  415,  16, -33, -25, },
+	{ -29, -13, 298,  960, 1393, 1101,  425,  18, -33, -24, },
+	{ -29, -15, 290,  949, 1392, 1110,  434,  21, -34, -22, },
+	{ -28, -17, 282,  939, 1390, 1120,  444,  25, -34, -25, },
+	{ -28, -18, 274,  928, 1388, 1129,  454,  28, -34, -25, },
+	{ -28, -20, 266,  917, 1386, 1138,  464,  31, -34, -24, },
+	{ -27, -21, 258,  906, 1384, 1147,  474,  34, -35, -24, },
+	{ -27, -22, 250,  895, 1381, 1156,  484,  38, -35, -24, },
+	{ -27, -23, 242,  885, 1379, 1164,  494,  41, -35, -24, },
+	{ -27, -25, 235,  874, 1376, 1173,  504,  45, -35, -24, },
+	{ -26, -26, 227,  863, 1373, 1181,  515,  49, -36, -24, },
+	{ -26, -27, 220,  852, 1369, 1190,  525,  53, -36, -24, },
+	{ -26, -28, 213,  841, 1366, 1198,  535,  56, -36, -23, },
+	{ -26, -29, 206,  830, 1362, 1206,  546,  61, -36, -24, },
+	{ -25, -29, 199,  819, 1358, 1214,  556,  65, -36, -25, },
+	{ -25, -30, 192,  808, 1354, 1222,  567,  69, -36, -25, },
+	{ -25, -31, 185,  797, 1350, 1229,  577,  73, -36, -23, },
+	{ -25, -32, 178,  785, 1346, 1237,  588,  78, -36, -23, },
+	{ -25, -32, 172,  774, 1341, 1244,  599,  83, -36, -24, },
+	{ -25, -33, 165,  763, 1336, 1252,  610,  87, -36, -23, },
+	{ -24, -33, 159,  752, 1331, 1259,  620,  92, -36, -24, },
+	{ -24, -34, 153,  741, 1326, 1266,  631,  97, -36, -24, },
+	{ -24, -34, 147,  730, 1321, 1272,  642, 102, -36, -24, },
+	{ -24, -35, 141,  719, 1315, 1279,  653, 107, -36, -23, },
+	{ -24, -35, 135,  708, 1310, 1285,  664, 113, -36, -24, },
+	{ -24, -35, 129,  697, 1304, 1292,  675, 118, -36, -24, },
+	{ -24, -36, 124,  686, 1298, 1298,  686, 124, -36, -24, },
+	{ -24, -36, 118,  675, 1292, 1304,  697, 129, -35, -24, },
+	{ -24, -36, 113,  664, 1285, 1310,  708, 135, -35, -24, },
+	{ -24, -36, 107,  653, 1279, 1315,  719, 141, -35, -23, },
+	{ -24, -36, 102,  642, 1272, 1321,  730, 147, -34, -24, },
+	{ -23, -36,  97,  631, 1266, 1326,  741, 153, -34, -25, },
+	{ -23, -36,  92,  620, 1259, 1331,  752, 159, -33, -25, },
+	{ -23, -36,  87,  610, 1252, 1336,  763, 165, -33, -25, },
+	{ -23, -36,  83,  599, 1244, 1341,  774, 172, -32, -26, },
+	{ -23, -36,  78,  588, 1237, 1346,  785, 178, -32, -25, },
+	{ -23, -36,  73,  577, 1229, 1350,  797, 185, -31, -25, },
+	{ -23, -36,  69,  567, 1222, 1354,  808, 192, -30, -27, },
+	{ -23, -36,  65,  556, 1214, 1358,  819, 199, -29, -27, },
+	{ -24, -36,  61,  546, 1206, 1362,  830, 206, -29, -26, },
+	{ -24, -36,  56,  535, 1198, 1366,  841, 213, -28, -25, },
+	{ -24, -36,  53,  525, 1190, 1369,  852, 220, -27, -26, },
+	{ -24, -36,  49,  515, 1181, 1373,  863, 227, -26, -26, },
+	{ -24, -35,  45,  504, 1173, 1376,  874, 235, -25, -27, },
+	{ -24, -35,  41,  494, 1164, 1379,  885, 242, -23, -27, },
+	{ -24, -35,  38,  484, 1156, 1381,  895, 250, -22, -27, },
+	{ -24, -35,  34,  474, 1147, 1384,  906, 258, -21, -27, },
+	{ -24, -34,  31,  464, 1138, 1386,  917, 266, -20, -28, },
+	{ -24, -34,  28,  454, 1129, 1388,  928, 274, -18, -29, },
+	{ -24, -34,  25,  444, 1120, 1390,  939, 282, -17, -29, },
+	{ -24, -34,  21,  434, 1110, 1392,  949, 290, -15, -27, },
+	{ -24, -33,  18,  425, 1101, 1393,  960, 298, -13, -29, },
+	{ -24, -33,  16,  415, 1091, 1395,  971, 307, -12, -30, },
+	{ -25, -33,  13,  406, 1082, 1396,  981, 315, -10, -29, },
+	{ -25, -32,  10,  396, 1072, 1397,  992, 324,  -8, -30, },
+	{ -25, -32,   8,  387, 1062, 1398, 1002, 333,  -6, -31, },
+	{ -25, -32,   5,  378, 1053, 1398, 1012, 341,  -4, -30, },
+	{ -25, -31,   3,  368, 1043, 1398, 1022, 350,  -2, -30, }
+};
+
+/* ScalingRatio = 4 */
+static const s16
+XV_fixedcoeff_taps10_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_10] = {
+	{   0, 107, 454, 924, 1150,  924, 454, 107,   0, -24, },
+	{   0, 104, 446, 917, 1149,  930, 461, 110,   0, -21, },
+	{  -1, 100, 439, 910, 1149,  936, 468, 114,   1, -20, },
+	{  -1,  97, 432, 904, 1149,  942, 475, 117,   2, -21, },
+	{  -2,  94, 425, 897, 1148,  948, 482, 121,   2, -19, },
+	{  -2,  91, 418, 890, 1147,  954, 490, 125,   3, -20, },
+	{  -3,  88, 411, 883, 1147,  960, 497, 128,   3, -18, },
+	{  -3,  85, 404, 876, 1146,  966, 504, 132,   4, -18, },
+	{  -3,  82, 397, 869, 1145,  972, 512, 136,   5, -19, },
+	{  -4,  79, 390, 862, 1144,  978, 519, 140,   5, -17, },
+	{  -4,  76, 384, 855, 1142,  983, 526, 144,   6, -16, },
+	{  -4,  74, 377, 848, 1141,  989, 534, 148,   7, -18, },
+	{  -5,  71, 370, 841, 1139,  995, 541, 152,   7, -15, },
+	{  -5,  68, 364, 834, 1138, 1000, 549, 156,   8, -16, },
+	{  -5,  66, 357, 827, 1136, 1005, 556, 160,   9, -15, },
+	{  -6,  63, 350, 820, 1134, 1011, 564, 165,  10, -15, },
+	{  -6,  61, 344, 812, 1132, 1016, 571, 169,  11, -14, },
+	{  -6,  59, 338, 805, 1130, 1021, 579, 174,  12, -16, },
+	{  -6,  56, 331, 798, 1128, 1026, 586, 178,  13, -14, },
+	{  -7,  54, 325, 790, 1126, 1031, 594, 183,  14, -14, },
+	{  -7,  52, 319, 783, 1124, 1036, 601, 187,  15, -14, },
+	{  -7,  50, 312, 776, 1121, 1041, 609, 192,  16, -14, },
+	{  -7,  48, 306, 768, 1119, 1045, 617, 197,  17, -14, },
+	{  -8,  46, 300, 761, 1116, 1050, 624, 202,  18, -13, },
+	{  -8,  44, 294, 753, 1113, 1054, 632, 207,  19, -12, },
+	{  -8,  42, 288, 746, 1110, 1059, 639, 212,  20, -12, },
+	{  -8,  40, 282, 738, 1107, 1063, 647, 217,  22, -12, },
+	{  -9,  38, 277, 731, 1104, 1067, 655, 222,  23, -12, },
+	{  -9,  36, 271, 723, 1101, 1071, 662, 227,  24, -10, },
+	{  -9,  35, 265, 715, 1097, 1075, 670, 232,  26, -10, },
+	{  -9,  33, 259, 708, 1094, 1079, 677, 238,  27, -10, },
+	{ -10,  32, 254, 700, 1091, 1083, 685, 243,  28, -10, },
+	{ -10,  30, 248, 693, 1087, 1087, 693, 248,  30, -10, },
+	{ -10,  28, 243, 685, 1083, 1091, 700, 254,  32, -10, },
+	{ -10,  27, 238, 677, 1079, 1094, 708, 259,  33,  -9, },
+	{ -11,  26, 232, 670, 1075, 1097, 715, 265,  35,  -8, },
+	{ -11,  24, 227, 662, 1071, 1101, 723, 271,  36,  -8, },
+	{ -11,  23, 222, 655, 1067, 1104, 731, 277,  38, -10, },
+	{ -12,  22, 217, 647, 1063, 1107, 738, 282,  40,  -8, },
+	{ -12,  20, 212, 639, 1059, 1110, 746, 288,  42,  -8, },
+	{ -12,  19, 207, 632, 1054, 1113, 753, 294,  44,  -8, },
+	{ -12,  18, 202, 624, 1050, 1116, 761, 300,  46,  -9, },
+	{ -13,  17, 197, 617, 1045, 1119, 768, 306,  48,  -8, },
+	{ -13,  16, 192, 609, 1041, 1121, 776, 312,  50,  -8, },
+	{ -13,  15, 187, 601, 1036, 1124, 783, 319,  52,  -8, },
+	{ -14,  14, 183, 594, 1031, 1126, 790, 325,  54,  -7, },
+	{ -14,  13, 178, 586, 1026, 1128, 798, 331,  56,  -6, },
+	{ -14,  12, 174, 579, 1021, 1130, 805, 338,  59,  -8, },
+	{ -15,  11, 169, 571, 1016, 1132, 812, 344,  61,  -5, },
+	{ -15,  10, 165, 564, 1011, 1134, 820, 350,  63,  -6, },
+	{ -16,   9, 160, 556, 1005, 1136, 827, 357,  66,  -4, },
+	{ -16,   8, 156, 549, 1000, 1138, 834, 364,  68,  -5, },
+	{ -16,   7, 152, 541,  995, 1139, 841, 370,  71,  -4, },
+	{ -17,   7, 148, 534,  989, 1141, 848, 377,  74,  -5, },
+	{ -17,   6, 144, 526,  983, 1142, 855, 384,  76,  -3, },
+	{ -18,   5, 140, 519,  978, 1144, 862, 390,  79,  -3, },
+	{ -18,   5, 136, 512,  972, 1145, 869, 397,  82,  -4, },
+	{ -19,   4, 132, 504,  966, 1146, 876, 404,  85,  -2, },
+	{ -19,   3, 128, 497,  960, 1147, 883, 411,  88,  -2, },
+	{ -20,   3, 125, 490,  954, 1147, 890, 418,  91,  -2, },
+	{ -20,   2, 121, 482,  948, 1148, 897, 425,  94,  -1, },
+	{ -21,   2, 117, 475,  942, 1149, 904, 432,  97,  -1, },
+	{ -21,   1, 114, 468,  936, 1149, 910, 439, 100,   0, },
+	{ -22,   0, 110, 461,  930, 1149, 917, 446, 104,   1, }
+};
+
+/* ScalingRatio = 4 */
+static const s16
+XV_fixedcoeff_taps12_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_12] = {
+	{ -19,   0, 152, 498, 893, 1070,  893, 498, 152,   0, -19, -22, },
+	{ -19,  -1, 147, 487, 879, 1059,  889, 499, 155,   1, -19,  19, },
+	{ -19,  -2, 143, 480, 874, 1059,  894, 506, 159,   2, -19,  19, },
+	{ -19,  -3, 139, 474, 869, 1059,  899, 512, 163,   3, -19,  19, },
+	{ -19,  -4, 136, 468, 863, 1059,  904, 519, 167,   4, -19,  18, },
+	{ -19,  -5, 132, 461, 858, 1058,  909, 525, 171,   5, -19,  20, },
+	{ -19,  -5, 128, 455, 853, 1058,  913, 531, 175,   7, -19,  19, },
+	{ -18,  -6, 125, 449, 847, 1057,  918, 538, 180,   8, -19,  17, },
+	{ -18,  -7, 121, 443, 842, 1056,  923, 544, 184,   9, -19,  18, },
+	{ -18,  -8, 118, 436, 836, 1056,  927, 551, 188,  10, -19,  19, },
+	{ -18,  -8, 114, 430, 831, 1055,  932, 557, 193,  12, -19,  17, },
+	{ -18,  -9, 111, 424, 825, 1054,  936, 564, 197,  13, -19,  18, },
+	{ -18, -10, 107, 418, 819, 1053,  941, 570, 202,  14, -19,  19, },
+	{ -18, -10, 104, 412, 814, 1052,  945, 577, 206,  16, -19,  17, },
+	{ -18, -11, 101, 406, 808, 1050,  949, 583, 211,  17, -19,  19, },
+	{ -18, -11,  98, 400, 802, 1049,  954, 590, 216,  19, -19,  16, },
+	{ -18, -12,  95, 394, 796, 1048,  958, 596, 220,  20, -19,  18, },
+	{ -18, -12,  92, 388, 791, 1046,  962, 603, 225,  22, -19,  16, },
+	{ -18, -13,  89, 382, 785, 1045,  966, 609, 230,  24, -19,  16, },
+	{ -18, -13,  86, 376, 779, 1043,  970, 616, 235,  25, -19,  16, },
+	{ -18, -14,  83, 370, 773, 1041,  973, 622, 240,  27, -19,  18, },
+	{ -18, -14,  80, 364, 767, 1039,  977, 629, 244,  29, -19,  18, },
+	{ -18, -15,  77, 358, 761, 1037,  981, 635, 249,  31, -19,  19, },
+	{ -18, -15,  74, 352, 755, 1035,  984, 642, 255,  33, -19,  18, },
+	{ -18, -15,  71, 347, 749, 1033,  988, 648, 260,  35, -19,  17, },
+	{ -18, -16,  69, 341, 743, 1031,  991, 654, 265,  36, -19,  19, },
+	{ -18, -16,  66, 335, 736, 1029,  995, 661, 270,  38, -19,  19, },
+	{ -18, -16,  64, 330, 730, 1026,  998, 667, 275,  41, -18,  17, },
+	{ -18, -17,  61, 324, 724, 1024, 1001, 674, 280,  43, -18,  18, },
+	{ -18, -17,  59, 318, 718, 1021, 1004, 680, 286,  45, -18,  18, },
+	{ -18, -17,  56, 313, 712, 1019, 1007, 686, 291,  47, -18,  18, },
+	{ -18, -17,  54, 307, 705, 1016, 1010, 693, 296,  49, -18,  19, },
+	{ -18, -18,  51, 302, 699, 1013, 1013, 699, 302,  51, -18,  20, },
+	{ -18, -18,  49, 296, 693, 1010, 1016, 705, 307,  54, -17,  19, },
+	{ -18, -18,  47, 291, 686, 1007, 1019, 712, 313,  56, -17,  18, },
+	{ -18, -18,  45, 286, 680, 1004, 1021, 718, 318,  59, -17,  18, },
+	{ -18, -18,  43, 280, 674, 1001, 1024, 724, 324,  61, -17,  18, },
+	{ -18, -18,  41, 275, 667,  998, 1026, 730, 330,  64, -16,  17, },
+	{ -18, -19,  38, 270, 661,  995, 1029, 736, 335,  66, -16,  19, },
+	{ -19, -19,  36, 265, 654,  991, 1031, 743, 341,  69, -16,  20, },
+	{ -19, -19,  35, 260, 648,  988, 1033, 749, 347,  71, -15,  18, },
+	{ -19, -19,  33, 255, 642,  984, 1035, 755, 352,  74, -15,  19, },
+	{ -19, -19,  31, 249, 635,  981, 1037, 761, 358,  77, -15,  20, },
+	{ -19, -19,  29, 244, 629,  977, 1039, 767, 364,  80, -14,  19, },
+	{ -19, -19,  27, 240, 622,  973, 1041, 773, 370,  83, -14,  19, },
+	{ -19, -19,  25, 235, 616,  970, 1043, 779, 376,  86, -13,  17, },
+	{ -19, -19,  24, 230, 609,  966, 1045, 785, 382,  89, -13,  17, },
+	{ -19, -19,  22, 225, 603,  962, 1046, 791, 388,  92, -12,  17, },
+	{ -19, -19,  20, 220, 596,  958, 1048, 796, 394,  95, -12,  19, },
+	{ -20, -19,  19, 216, 590,  954, 1049, 802, 400,  98, -11,  18, },
+	{ -20, -19,  17, 211, 583,  949, 1050, 808, 406, 101, -11,  21, },
+	{ -20, -19,  16, 206, 577,  945, 1052, 814, 412, 104, -10,  19, },
+	{ -20, -19,  14, 202, 570,  941, 1053, 819, 418, 107, -10,  21, },
+	{ -20, -19,  13, 197, 564,  936, 1054, 825, 424, 111,  -9,  20, },
+	{ -20, -19,  12, 193, 557,  932, 1055, 831, 430, 114,  -8,  19, },
+	{ -21, -19,  10, 188, 551,  927, 1056, 836, 436, 118,  -8,  22, },
+	{ -21, -19,   9, 184, 544,  923, 1056, 842, 443, 121,  -7,  21, },
+	{ -21, -19,   8, 180, 538,  918, 1057, 847, 449, 125,  -6,  20, },
+	{ -21, -19,   7, 175, 531,  913, 1058, 853, 455, 128,  -5,  21, },
+	{ -21, -19,   5, 171, 525,  909, 1058, 858, 461, 132,  -5,  22, },
+	{ -21, -19,   4, 167, 519,  904, 1059, 863, 468, 136,  -4,  20, },
+	{ -22, -19,   3, 163, 512,  899, 1059, 869, 474, 139,  -3,  22, },
+	{ -22, -19,   2, 159, 506,  894, 1059, 874, 480, 143,  -2,  22, },
+	{ -22, -19,   1, 155, 499,  889, 1059, 879, 487, 147,  -1,  22, }
+};
+
+enum xilinx_scaler_vid_reg_fmts {
+	XVIDC_CSF_RGB = 0,
+	XVIDC_CSF_YCRCB_444,
+	XVIDC_CSF_YCRCB_422,
+	XVIDC_CSF_YCRCB_420,
+};
+
+static const u32 xilinx_scaler_video_fmts[] = {
+	MEDIA_BUS_FMT_RGB888_1X24,
+	MEDIA_BUS_FMT_VUY8_1X24,
+	MEDIA_BUS_FMT_UYVY8_1X16,
+	MEDIA_BUS_FMT_VYYUYY8_1X24,
+};
+
+/* This bit is for xscaler feature flag */
+#define XSCALER_HPHASE_FIX	BIT(0)
+
+/**
+ * struct xscaler_feature - dt or IP property structure
+ * @flags: Bitmask of properties enabled in IP or dt
+ */
+struct xscaler_feature {
+	u32 flags;
+};
+
+/**
+ * struct xilinx_scaler - Core configuration of scaler device structure
+ * @base: pointer to register base address
+ * @dev: device structure
+ * @bridge: xilinx bridge
+ * @width_in: input width
+ * @height_in: input height
+ * @width_out: output width
+ * @height_out: output height
+ * @fmt_in: input format
+ * @fmt_out: output format
+ * @num_hori_taps: number of horizontal taps
+ * @num_vert_taps: number of vertical taps
+ * @max_num_phases: maximum number of phases
+ * @pix_per_clk: Pixels per Clock cycle the IP operates upon
+ * @max_pixels: The maximum number of pixels that the H-scaler examines
+ * @max_lines: The maximum number of lines that the V-scaler examines
+ * @H_phases: The phases needed to program the H-scaler for different taps
+ * @hscaler_coeff: The complete array of H-scaler coefficients
+ * @vscaler_coeff: The complete array of V-scaler coefficients
+ * @is_polyphase: Track if scaling algorithm is polyphase or not
+ * @rst_gpio: GPIO reset line to bring VPSS Scaler out of reset
+ * @ctrl_clk: AXI Lite clock
+ * @axis_clk: Video Clock
+ * @cfg: Pointer to scaler config structure
+ */
+struct xilinx_scaler {
+	void __iomem *base;
+	struct device *dev;
+	struct xlnx_bridge bridge;
+	u32 width_in;
+	u32 height_in;
+	u32 width_out;
+	u32 height_out;
+	u32 fmt_in;
+	u32 fmt_out;
+	u32 num_hori_taps;
+	u32 num_vert_taps;
+	u32 max_num_phases;
+	u32 pix_per_clk;
+	u32 max_pixels;
+	u32 max_lines;
+	u32 H_phases[XV_HSCALER_MAX_LINE_WIDTH];
+	short hscaler_coeff[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_MAX_H_TAPS];
+	short vscaler_coeff[XV_VSCALER_MAX_V_PHASES][XV_VSCALER_MAX_V_TAPS];
+	bool is_polyphase;
+	struct gpio_desc *rst_gpio;
+	struct clk *ctrl_clk;
+	struct clk *axis_clk;
+	const struct xscaler_feature *cfg;
+};
+
+static inline void xilinx_scaler_write(void __iomem *base, u32 offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static inline u32 xilinx_scaler_read(void __iomem *base, u32 offset)
+{
+	return readl(base + offset);
+}
+
+static inline void xilinx_scaler_clr(void __iomem *base, u32 offset, u32 clr)
+{
+	xilinx_scaler_write(base, offset,
+			    xilinx_scaler_read(base, offset) & ~clr);
+}
+
+static inline void xilinx_scaler_set(void __iomem *base, u32 offset, u32 set)
+{
+	xilinx_scaler_write(base, offset,
+			    xilinx_scaler_read(base, offset) | set);
+}
+
+static inline void
+xilinx_scaler_disable_block(struct xilinx_scaler *scaler, u32 channel,
+			    u32 ip_block)
+{
+	xilinx_scaler_clr(scaler->base, ((channel - 1) * XGPIO_CHAN_OFFSET) +
+			  XGPIO_DATA_OFFSET + S_AXIS_RESET_OFF, ip_block);
+}
+
+static inline void
+xilinx_scaler_enable_block(struct xilinx_scaler *scaler, u32 channel,
+			   u32 ip_block)
+{
+	xilinx_scaler_set(scaler->base, ((channel - 1) * XGPIO_CHAN_OFFSET) +
+			  XGPIO_DATA_OFFSET + S_AXIS_RESET_OFF, ip_block);
+}
+
+/**
+ * bridge_to_layer - Gets the parent structure
+ * @bridge: pointer to the member.
+ *
+ * Return: parent structure pointer
+ */
+static inline struct xilinx_scaler *bridge_to_layer(struct xlnx_bridge *bridge)
+{
+	return container_of(bridge, struct xilinx_scaler, bridge);
+}
+
+/**
+ * xilinx_scaler_reset - Resets scaler block
+ * @scaler: Pointer to scaler device structure
+ *
+ * This function resets scaler block
+ */
+static void xilinx_scaler_reset(struct xilinx_scaler *scaler)
+{
+	xilinx_scaler_disable_block(scaler, XGPIO_CH_RESET_SEL,
+				    XGPIO_RESET_MASK_ALL_BLOCKS);
+	xilinx_scaler_enable_block(scaler, XGPIO_CH_RESET_SEL,
+				   XGPIO_RESET_MASK_IP_AXIS);
+}
+
+/**
+ * xv_hscaler_calculate_phases - Calculates h-scaler phases
+ * @scaler: Pointer to scaler registers base
+ * @width_in: input width
+ * @width_out: output width
+ * @pixel_rate: pixel rate
+ */
+static void
+xv_hscaler_calculate_phases(struct xilinx_scaler *scaler,
+			    u32 width_in, u32 width_out, u32 pixel_rate)
+{
+	unsigned int loop_width;
+	unsigned int x, s;
+	int offset = 0;
+	int xwrite_pos = 0;
+	bool output_write_en;
+	bool get_new_pix;
+	u64 phaseH;
+	u32 array_idx = 0;
+	int nr_rds;
+	int nr_rds_clck;
+	unsigned int nphases = scaler->max_num_phases;
+	unsigned int nppc = scaler->pix_per_clk;
+	unsigned int shift = XHSC_STEP_PRECISION_SHIFT - ilog2(nphases);
+
+	loop_width = max_t(u32, width_in, width_out);
+	loop_width = ALIGN(loop_width + nppc - 1, nppc);
+
+	for (x = 0; x < loop_width; x++) {
+		nr_rds_clck = 0;
+		for (s = 0; s < nppc; s++) {
+			phaseH = (offset >> shift) & (nphases - 1);
+			get_new_pix = false;
+			output_write_en = false;
+			if ((offset >> XHSC_STEP_PRECISION_SHIFT) != 0) {
+				get_new_pix = true;
+				offset -= (1 << XHSC_STEP_PRECISION_SHIFT);
+				array_idx++;
+			}
+
+			if (((offset >> XHSC_STEP_PRECISION_SHIFT) == 0) &&
+			    xwrite_pos < width_out) {
+				offset += pixel_rate;
+				output_write_en = true;
+				xwrite_pos++;
+			}
+
+			scaler->H_phases[x] |= (phaseH <<
+						(s * XHSC_HPHASE_MULTIPLIER));
+			scaler->H_phases[x] |= (array_idx <<
+						(XHSC_HPHASE_SHIFT_BY_6 +
+						(s * XHSC_HPHASE_MULTIPLIER)));
+			if (output_write_en) {
+				scaler->H_phases[x] |=
+				(XV_HSCALER_PHASESH_V_OUTPUT_WR_EN <<
+				(s * XHSC_HPHASE_MULTIPLIER));
+			}
+
+			if (get_new_pix)
+				nr_rds_clck++;
+		}
+		if (array_idx >= nppc)
+			array_idx &= (nppc - 1);
+
+		nr_rds += nr_rds_clck;
+		if (nr_rds >= nppc)
+			nr_rds -= nppc;
+	}
+}
+
+/**
+ * xv_hscaler_load_ext_coeff - Loads external coefficients of h-scaler
+ * @scaler: Pointer to scaler registers base
+ * @coeff: Pointer to coeff array
+ * @ntaps: number of taps
+ *
+ * This function loads h-scaler coefficients.
+ */
+static void
+xv_hscaler_load_ext_coeff(struct xilinx_scaler *scaler,
+			  const short *coeff, u32 ntaps)
+{
+	unsigned int i, j, pad, offset;
+	u32 nphases = scaler->max_num_phases;
+
+	/* Determine if coefficient needs padding (effective vs. max taps) */
+	pad = XV_HSCALER_MAX_H_TAPS - ntaps;
+	offset = pad >> 1;
+	/* Load coefficients into scaler coefficient table */
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps; ++j)
+			scaler->hscaler_coeff[i][j + offset] =
+						coeff[i * ntaps + j];
+	}
+
+	if (pad) {
+		for (i = 0; i < nphases; i++) {
+			for (j = 0; j < offset; j++)
+				scaler->hscaler_coeff[i][j] = 0;
+			j = ntaps + offset;
+			for (; j < XV_HSCALER_MAX_H_TAPS; j++)
+				scaler->hscaler_coeff[i][j] = 0;
+		}
+	}
+}
+
+static const short *xv_select_coeff(struct xilinx_scaler *scaler,
+				    u32 in, u32 out, u32 *ntaps)
+{
+	const short *coeff = NULL;
+
+	/*
+	 * Scale Down Mode will use dynamic filter selection logic
+	 * Scale Up Mode (including 1:1) will always use 6 tap filter
+	 */
+	if (out < in) {
+		u16 scale_ratio = (in * 10) / out;
+
+		/* Since XV_HSCALER_TAPS_* is same as XV_VSCALER_TAPS_* */
+		switch (*ntaps) {
+		case XV_HSCALER_TAPS_6:
+			*ntaps = XV_HSCALER_TAPS_6;
+			if (scale_ratio > 35)
+				coeff = &XV_fixedcoeff_taps6_SR4[0][0];
+			else if (scale_ratio > 25)
+				coeff = &XV_fixedcoeff_taps6_SR3[0][0];
+			else if (scale_ratio > 15)
+				coeff = &XV_fixedcoeff_taps6_SR2[0][0];
+			else
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+			break;
+		case XV_HSCALER_TAPS_8:
+			if (scale_ratio > 35) {
+				coeff = &XV_fixedcoeff_taps8_SR4[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else if (scale_ratio > 25) {
+				coeff = &XV_fixedcoeff_taps8_SR3[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else if (scale_ratio > 15) {
+				coeff = &XV_fixedcoeff_taps8_SR2[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else {
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+				*ntaps = XV_HSCALER_TAPS_6;
+			}
+			break;
+		case XV_HSCALER_TAPS_10:
+			if (scale_ratio > 35) {
+				coeff = &XV_fixedcoeff_taps10_SR4[0][0];
+				*ntaps = XV_HSCALER_TAPS_10;
+			} else if (scale_ratio > 25) {
+				coeff = &XV_fixedcoeff_taps10_SR3[0][0];
+				*ntaps = XV_HSCALER_TAPS_10;
+			} else if (scale_ratio > 15) {
+				coeff = &XV_fixedcoeff_taps8_SR2[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else {
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+				*ntaps = XV_HSCALER_TAPS_6;
+			}
+			break;
+		case XV_HSCALER_TAPS_12:
+			if (scale_ratio > 35) {
+				coeff = &XV_fixedcoeff_taps12_SR4[0][0];
+				*ntaps = XV_HSCALER_TAPS_12;
+			} else if (scale_ratio > 25) {
+				coeff = &XV_fixedcoeff_taps10_SR3[0][0];
+				*ntaps = XV_HSCALER_TAPS_10;
+			} else if (scale_ratio > 15) {
+				coeff = &XV_fixedcoeff_taps8_SR2[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else {
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+				*ntaps = XV_HSCALER_TAPS_6;
+			}
+			break;
+		default:
+			dev_err(scaler->dev,
+				"Unsupported number of taps = %d",
+				*ntaps);
+		}
+	} else {
+		dev_dbg(scaler->dev, "scaler : scale up 6 tap");
+		coeff = &XV_lanczos2_taps6[0][0];
+		*ntaps = XV_HSCALER_TAPS_6;
+	}
+
+	return coeff;
+}
+
+/**
+ * xv_hscaler_coeff_select - Selection of H-Scaler coefficients of operation
+ * @scaler: Pointer to Scaler device structure
+ * @width_in: Width of input video
+ * @width_out: Width of desired output video
+ *
+ * There are instances when a N-tap filter might operate in an M-tap
+ * configuration where N > M.
+ *
+ * For example :
+ * Depending on the ratio of scaling (while downscaling), a 12-tap
+ * filter may operate with 10 tap coefficients and zero-pads the remaining
+ * coefficients.
+ *
+ * While upscaling the driver will program 6-tap filter coefficients
+ * in any N-tap configurations (for N >= 6).
+ *
+ * This selection is adopted by the as it gives optimal
+ * video output determined by repeated testing of the IP
+ *
+ * Return: Will return 0 if successful. Returns -EINVAL on an unsupported
+ * H-scaler number of taps.
+ */
+static int
+xv_hscaler_select_coeff(struct xilinx_scaler *scaler,
+			u32 width_in, u32 width_out)
+{
+	const short *coeff;
+	u32 ntaps = scaler->num_hori_taps;
+
+	coeff = xv_select_coeff(scaler, width_in, width_out, &ntaps);
+	if (!coeff)
+		return -EINVAL;
+
+	xv_hscaler_load_ext_coeff(scaler, coeff, ntaps);
+	return 0;
+}
+
+/**
+ * xv_hscaler_set_coeff - Sets h-scaler coefficients
+ * @scaler: Pointer to scaler device structure
+ *
+ * This function sets coefficients of h-scaler.
+ */
+static void xv_hscaler_set_coeff(struct xilinx_scaler *scaler)
+{
+	int val, i, j, offset, rd_indx;
+	u32 ntaps = scaler->num_hori_taps;
+	u32 nphases = scaler->max_num_phases;
+	u32 base_addr;
+
+	offset = (XV_HSCALER_MAX_H_TAPS - ntaps) / 2;
+	base_addr = V_HSCALER_OFF + XV_HSCALER_CTRL_ADDR_HWREG_HFLTCOEFF_BASE;
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps / 2; j++) {
+			rd_indx = j * 2 + offset;
+			val = (scaler->hscaler_coeff[i][rd_indx + 1] <<
+			       XSCALER_BITSHIFT_16) |
+			       (scaler->hscaler_coeff[i][rd_indx] &
+			       XHSC_MASK_LOW_16BITS);
+			xilinx_scaler_write(scaler->base, base_addr +
+				((i * ntaps / 2 + j) * 4), val);
+		}
+	}
+}
+
+/**
+ * xv_vscaler_load_ext_coeff - Loads external coefficients of v-scaler
+ * @scaler: Pointer to scaler device structure
+ * @coeff: Pointer to coeff array
+ * @ntaps: number of taps
+ *
+ * This function loads v-scaler coefficients.
+ */
+static void
+xv_vscaler_load_ext_coeff(struct xilinx_scaler *scaler,
+			  const short *coeff, u32 ntaps)
+{
+	int i, j, pad, offset;
+	u32 nphases = scaler->max_num_phases;
+
+	/* Determine if coefficient needs padding (effective vs. max taps) */
+	pad = XV_VSCALER_MAX_V_TAPS - ntaps;
+	offset = pad ? (pad >> 1) : 0;
+	/* Load User defined coefficients into scaler coefficient table */
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps; ++j)
+			scaler->vscaler_coeff[i][j + offset] =
+						coeff[i * ntaps + j];
+	}
+	if (pad) {
+		/* effective taps < max_taps */
+		for (i = 0; i < nphases; i++) {
+			/* pad left */
+			for (j = 0; j < offset; j++)
+				scaler->vscaler_coeff[i][j] = 0;
+			/* pad right */
+			j = ntaps + offset;
+			for (; j < XV_VSCALER_MAX_V_TAPS; j++)
+				scaler->vscaler_coeff[i][j] = 0;
+		}
+	}
+}
+
+/**
+ * xv_vscaler_set_coeff - Sets v-scaler coefficients
+ * @scaler: Pointer to scaler device structure
+ *
+ * This function sets coefficients of v-scaler.
+ */
+static void xv_vscaler_set_coeff(struct xilinx_scaler *scaler)
+{
+	u32 nphases = scaler->max_num_phases;
+	u32 ntaps = scaler->num_vert_taps;
+	int val, i, j, offset, rd_indx;
+	u32 base_addr;
+
+	offset = (XV_VSCALER_MAX_V_TAPS - ntaps) / 2;
+	base_addr = V_VSCALER_OFF + XV_VSCALER_CTRL_ADDR_HWREG_VFLTCOEFF_BASE;
+
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps / 2; j++) {
+			rd_indx = j * 2 + offset;
+			val = (scaler->vscaler_coeff[i][rd_indx + 1] <<
+			       XSCALER_BITSHIFT_16) |
+			       (scaler->vscaler_coeff[i][rd_indx] &
+			       XVSC_MASK_LOW_16BITS);
+			xilinx_scaler_write(scaler->base, base_addr +
+				((i * ntaps / 2 + j) * 4), val);
+		}
+	}
+}
+
+/**
+ * xv_vscaler_coeff_select - Selection of V-Scaler coefficients of operation
+ * @scaler: Pointer to Scaler device structure
+ * @height_in: Height of input video
+ * @height_out: Height of desired output video
+ *
+ * There are instances when a N-tap filter might operate in an M-tap
+ * configuration where N > M.
+ *
+ * For example :
+ * Depending on the ratio of scaling (while downscaling), a 10-tap
+ * filter may operate with 6 tap coefficients and zero-pads the remaining
+ * coefficients.
+ *
+ * While upscaling the driver will program 6-tap filter coefficients
+ * in any N-tap configurations (for N >= 6).
+ *
+ * This selection is adopted by the as it gives optimal
+ * video output determined by repeated testing of the IP
+ *
+ * Return: Will return 0 if successful. Returns -EINVAL on an unsupported
+ * V-scaler number of taps.
+ */
+static int
+xv_vscaler_select_coeff(struct xilinx_scaler *scaler,
+			u32 height_in, u32 height_out)
+{
+	const short *coeff;
+	u32 ntaps = scaler->num_vert_taps;
+
+	coeff = xv_select_coeff(scaler, height_in, height_out, &ntaps);
+	if (!coeff)
+		return -EINVAL;
+
+	xv_vscaler_load_ext_coeff(scaler, coeff, ntaps);
+	return 0;
+}
+
+/**
+ * xv_hscaler_set_phases - Sets phases of h-scaler
+ * @scaler: Pointer to scaler device structure
+ *
+ * This function sets phases of h-scaler.
+ */
+static void
+xv_hscaler_set_phases(struct xilinx_scaler *scaler)
+{
+	u32 loop_width;
+	u32 index, val;
+	u32 offset, i, lsb, msb;
+
+	loop_width = scaler->max_pixels / scaler->pix_per_clk;
+	if (scaler->cfg->flags & XSCALER_HPHASE_FIX) {
+		offset = V_HSCALER_OFF +
+			XV_HSCALER_CTRL_ADDR_HWREG_PHASEH_FIX;
+	} else {
+		offset = V_HSCALER_OFF +
+			XV_HSCALER_CTRL_ADDR_HWREG_PHASESH_V_BASE;
+	}
+
+	switch (scaler->pix_per_clk) {
+	case XSCALER_PPC_1:
+		index = 0;
+		for (i = 0; i < loop_width; i += 2) {
+			lsb = scaler->H_phases[i] & XHSC_MASK_LOW_16BITS;
+			msb = scaler->H_phases[i + 1] & XHSC_MASK_LOW_16BITS;
+			val = (msb << 16 | lsb);
+			xilinx_scaler_write(scaler->base, offset +
+				(index * 4), val);
+			++index;
+		}
+		return;
+	case XSCALER_PPC_2:
+		for (i = 0; i < loop_width; i++) {
+			val = (scaler->H_phases[i] & XHSC_MASK_LOW_32BITS);
+			xilinx_scaler_write(scaler->base, offset +
+				(i * 4), val);
+		}
+		return;
+	}
+}
+
+/**
+ * xv_vscaler_setup_video_fmt - Sets video format of v-scaler
+ * @scaler: Pointer to scaler device structure
+ * @code_in: format to be set
+ *
+ * This function set the given format of v-scaler
+ *
+ * Return: format value on success. -EINVAL for invalid format.
+ *
+ */
+static int
+xv_vscaler_setup_video_fmt(struct xilinx_scaler *scaler, u32 code_in)
+{
+	u32 video_in;
+
+	switch (code_in) {
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+		video_in = XVIDC_CSF_YCRCB_422;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+		video_in = XVIDC_CSF_YCRCB_444;
+		break;
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		video_in = XVIDC_CSF_RGB;
+		break;
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		video_in = XVIDC_CSF_YCRCB_420;
+		break;
+	default:
+		dev_info(scaler->dev, "Vscaler Unsupported media fmt\n");
+		return -EINVAL;
+	}
+	xilinx_scaler_write(scaler->base, V_VSCALER_OFF +
+			    XV_VSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA,
+			    video_in);
+	return video_in;
+}
+
+/**
+ * xv_hscaler_setup_video_fmt - Sets video format of h-scaler
+ * @scaler: Pointer to scaler device structure
+ * @code_out: bus format to be set
+ * @vsc_out: return value of vscaler
+ *
+ * This function set the given video format of h-scaler
+ *
+ * Return: format value on success. -EINVAL for invalid format.
+ *
+ */
+static int xv_hscaler_setup_video_fmt(struct xilinx_scaler *scaler,
+				      u32 code_out, u32 vsc_out)
+{
+	u32 video_out;
+
+	switch (vsc_out) {
+	case XVIDC_CSF_YCRCB_422:
+		break;
+	case XVIDC_CSF_YCRCB_444:
+		break;
+	case XVIDC_CSF_RGB:
+		break;
+	case XVIDC_CSF_YCRCB_420:
+		break;
+	default:
+		dev_info(scaler->dev, "unsupported format from Vscaler");
+		return -EINVAL;
+	}
+
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+		XV_HSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA,
+		vsc_out);
+
+	switch (code_out) {
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+		video_out = XVIDC_CSF_YCRCB_422;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+		video_out = XVIDC_CSF_YCRCB_444;
+		break;
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		video_out = XVIDC_CSF_RGB;
+		break;
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		video_out = XVIDC_CSF_YCRCB_420;
+		break;
+	default:
+		dev_info(scaler->dev, "Hscaler Unsupported Out media fmt\n");
+		return -EINVAL;
+	}
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+			    XV_HSCALER_CTRL_ADDR_HWREG_COLORMODEOUT_DATA,
+			    video_out);
+	return 0;
+}
+
+/**
+ * xilinx_scaler_parse_of - Parse device tree information
+ * @scaler: Pointer to scaler device structure
+ *
+ * This function reads the device tree contents
+ *
+ * Return: 0 on success. -EINVAL for invalid value.
+ *
+ */
+static int xilinx_scaler_parse_of(struct xilinx_scaler *scaler)
+{
+	int ret;
+	u32 dt_ppc;
+	struct device_node *node = scaler->dev->of_node;
+
+	scaler->ctrl_clk = devm_clk_get(scaler->dev, "aclk_ctrl");
+	if (IS_ERR(scaler->ctrl_clk)) {
+		ret = PTR_ERR(scaler->ctrl_clk);
+		dev_err(scaler->dev, "failed to get axi lite clk %d\n", ret);
+		return ret;
+	}
+
+	scaler->axis_clk = devm_clk_get(scaler->dev, "aclk_axis");
+	if (IS_ERR(scaler->axis_clk)) {
+		ret = PTR_ERR(scaler->axis_clk);
+		dev_err(scaler->dev, "failed to get video clk %d\n", ret);
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,h-scaler-taps",
+				   &scaler->num_hori_taps);
+	if (ret < 0) {
+		dev_info(scaler->dev, "h-scaler-taps not present in DT\n");
+		return ret;
+	}
+	switch (scaler->num_hori_taps) {
+	case XV_HSCALER_TAPS_2:
+	case XV_HSCALER_TAPS_4:
+		scaler->is_polyphase = false;
+		break;
+	case XV_HSCALER_TAPS_6:
+	case XV_HSCALER_TAPS_8:
+	case XV_HSCALER_TAPS_10:
+	case XV_HSCALER_TAPS_12:
+		scaler->is_polyphase = true;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,v-scaler-taps",
+				   &scaler->num_vert_taps);
+	if (ret < 0) {
+		dev_info(scaler->dev, "v-scaler-taps not present in DT\n");
+		return ret;
+	}
+
+	switch (scaler->num_vert_taps) {
+	case XV_HSCALER_TAPS_2:
+	case XV_VSCALER_TAPS_4:
+		if (scaler->num_vert_taps != scaler->num_hori_taps)
+			return -EINVAL;
+		break;
+	case XV_VSCALER_TAPS_6:
+	case XV_VSCALER_TAPS_8:
+	case XV_VSCALER_TAPS_10:
+	case XV_VSCALER_TAPS_12:
+		scaler->is_polyphase = true;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,samples-per-clk", &dt_ppc);
+	if (ret < 0) {
+		dev_info(scaler->dev, "PPC is missing in DT\n");
+		return ret;
+	}
+	if (dt_ppc != XSCALER_PPC_1 && dt_ppc != XSCALER_PPC_2) {
+		dev_info(scaler->dev, "Unsupported ppc: %d", dt_ppc);
+		return -EINVAL;
+	}
+	scaler->pix_per_clk = dt_ppc;
+
+	/* Reset GPIO */
+	scaler->rst_gpio = devm_gpiod_get(scaler->dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(scaler->rst_gpio)) {
+		if (PTR_ERR(scaler->rst_gpio) != -EPROBE_DEFER)
+			dev_err(scaler->dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(scaler->rst_gpio);
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-height",
+				   &scaler->max_lines);
+	if (ret < 0) {
+		dev_err(scaler->dev, "xlnx,max-height is missing!");
+		return -EINVAL;
+	} else if (scaler->max_lines > XSCALER_MAX_HEIGHT ||
+		   scaler->max_lines < XSCALER_MIN_HEIGHT) {
+		dev_err(scaler->dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-width",
+				   &scaler->max_pixels);
+	if (ret < 0) {
+		dev_err(scaler->dev, "xlnx,max-width is missing!");
+		return -EINVAL;
+	} else if (scaler->max_pixels > XSCALER_MAX_WIDTH ||
+		   scaler->max_pixels < XSCALER_MIN_WIDTH) {
+		dev_err(scaler->dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * xilinx_scaler_stream - Set up v-scaler and h-scaler for streaming
+ * @scaler: Pointer to scaler device structure
+ *
+ * This function sets up the required configuration of v-scaler and h-scaler
+ *
+ * Return: 0 on success. Returns -EINVAL on failure conditions.
+ */
+static int xilinx_scaler_stream(struct xilinx_scaler *scaler)
+{
+	u32 fmt_in, fmt_out;
+	u32 pixel_rate;
+	u32 line_rate;
+	int ret;
+
+	fmt_in = scaler->fmt_in;
+	fmt_out = scaler->fmt_out;
+	line_rate = (scaler->height_in * STEP_PRECISION) / scaler->height_out;
+
+	if (scaler->is_polyphase) {
+		ret = xv_vscaler_select_coeff(scaler, scaler->height_in,
+					      scaler->height_out);
+		if (ret < 0) {
+			dev_info(scaler->dev, "Failed: vscaler select coeff\n");
+			return ret;
+		}
+		xv_vscaler_set_coeff(scaler);
+	}
+	xilinx_scaler_write(scaler->base, V_VSCALER_OFF +
+			    XV_VSCALER_CTRL_ADDR_HWREG_LINERATE_DATA,
+			    line_rate);
+	ret = xv_vscaler_setup_video_fmt(scaler, scaler->fmt_in);
+	if (ret < 0) {
+		dev_info(scaler->dev, "Failed: vscaler setup video format\n");
+		return ret;
+	}
+	pixel_rate = (scaler->width_in * STEP_PRECISION) / scaler->width_out;
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+			    XV_HSCALER_CTRL_ADDR_HWREG_PIXELRATE_DATA,
+			    pixel_rate);
+	ret = xv_hscaler_setup_video_fmt(scaler, scaler->fmt_out, ret);
+	if (ret < 0) {
+		dev_info(scaler->dev, "Failed: vscaler setup video format\n");
+		return ret;
+	}
+	if (scaler->is_polyphase) {
+		ret = xv_hscaler_select_coeff(scaler, scaler->width_in,
+					      scaler->width_out);
+		if (ret < 0) {
+			dev_info(scaler->dev, "Failed: hscaler select coeff\n");
+			return ret;
+		}
+		xv_hscaler_set_coeff(scaler);
+	}
+	xv_hscaler_calculate_phases(scaler, scaler->width_in,
+				    scaler->width_out, pixel_rate);
+	xv_hscaler_set_phases(scaler);
+	return 0;
+}
+
+/**
+ * xilinx_scaler_bridge_enable - enabes scaler sub-cores
+ * @bridge: bridge instance
+ *
+ * This function enables the scaler sub-cores
+ *
+ * Return: 0 on success. Return -EINVAL on failure conditions.
+ *
+ */
+static int xilinx_scaler_bridge_enable(struct xlnx_bridge *bridge)
+{
+	int ret;
+	struct xilinx_scaler *scaler = bridge_to_layer(bridge);
+
+	ret = xilinx_scaler_stream(scaler);
+	if (ret)
+		return ret;
+
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+			    XV_HSCALER_CTRL_ADDR_AP_CTRL, XSCALER_STREAM_ON);
+	xilinx_scaler_write(scaler->base, V_VSCALER_OFF +
+			    XV_VSCALER_CTRL_ADDR_AP_CTRL, XSCALER_STREAM_ON);
+	xilinx_scaler_enable_block(scaler, XGPIO_CH_RESET_SEL,
+				   XGPIO_RESET_MASK_IP_AXIS);
+	return ret;
+}
+
+/**
+ * xilinx_scaler_bridge_disable - disables scaler sub-cores
+ * @bridge: bridge instance
+ *
+ * This function disables the scaler sub-cores
+ */
+static void xilinx_scaler_bridge_disable(struct xlnx_bridge *bridge)
+{
+	struct xilinx_scaler *scaler = bridge_to_layer(bridge);
+
+	xilinx_scaler_disable_block(scaler, XGPIO_CH_RESET_SEL,
+				    XGPIO_RESET_MASK_ALL_BLOCKS);
+}
+
+/**
+ * xilinx_scaler_bridge_set_input - Sets the input parameters of scaler
+ * @bridge: bridge instance
+ * @width: width of video
+ * @height: height of video
+ * @bus_fmt: video bus format
+ *
+ * This function sets the input parameters of scaler
+ * Return: 0 on success. -EINVAL for invalid parameters.
+ */
+static int xilinx_scaler_bridge_set_input(struct xlnx_bridge *bridge,
+					  u32 width, u32 height, u32 bus_fmt)
+{
+	struct xilinx_scaler *scaler = bridge_to_layer(bridge);
+
+	if (width > scaler->max_pixels || height > scaler->max_lines)
+		return -EINVAL;
+
+	scaler->height_in = height;
+	scaler->width_in = width;
+	scaler->fmt_in = bus_fmt;
+
+	/* IP Reset through GPIO */
+	gpiod_set_value_cansleep(scaler->rst_gpio, XSCALER_RESET_ASSERT);
+	gpiod_set_value_cansleep(scaler->rst_gpio, XSCALER_RESET_DEASSERT);
+	xilinx_scaler_reset(scaler);
+	memset(scaler->H_phases, 0, sizeof(scaler->H_phases));
+
+	xilinx_scaler_write(scaler->base, V_VSCALER_OFF +
+			    XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTIN_DATA, height);
+	xilinx_scaler_write(scaler->base, V_VSCALER_OFF +
+			    XV_VSCALER_CTRL_ADDR_HWREG_WIDTH_DATA, width);
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+			    XV_HSCALER_CTRL_ADDR_HWREG_WIDTHIN_DATA, width);
+
+	return 0;
+}
+
+/**
+ * xilinx_scaler_bridge_get_input_fmts - input formats supported by scaler
+ * @bridge: bridge instance
+ * @fmts: Pointer to be updated with formats information
+ * @count: count of video bus formats
+ *
+ * This function provides the input video formats information scaler
+ * Return: 0 on success.
+ */
+static int xilinx_scaler_bridge_get_input_fmts(struct xlnx_bridge *bridge,
+					       const u32 **fmts, u32 *count)
+{
+	*fmts = xilinx_scaler_video_fmts;
+	*count = ARRAY_SIZE(xilinx_scaler_video_fmts);
+	return 0;
+}
+
+/**
+ * xilinx_scaler_bridge_set_output - Sets the output parameters of scaler
+ * @bridge: bridge instance
+ * @width: width of video
+ * @height: height of video
+ * @bus_fmt: video bus format
+ *
+ * This function sets the output parameters of scaler
+ * Return: 0 on success. -EINVAL for invalid parameters.
+ */
+static int xilinx_scaler_bridge_set_output(struct xlnx_bridge *bridge,
+					   u32 width, u32 height, u32 bus_fmt)
+{
+	struct xilinx_scaler *scaler = bridge_to_layer(bridge);
+
+	if (width > scaler->max_pixels || height > scaler->max_lines)
+		return -EINVAL;
+
+	scaler->height_out = height;
+	scaler->width_out = width;
+	scaler->fmt_out = bus_fmt;
+
+	xilinx_scaler_write(scaler->base, V_VSCALER_OFF +
+			    XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTOUT_DATA, height);
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+			    XV_HSCALER_CTRL_ADDR_HWREG_HEIGHT_DATA, height);
+	xilinx_scaler_write(scaler->base, V_HSCALER_OFF +
+			    XV_HSCALER_CTRL_ADDR_HWREG_WIDTHOUT_DATA, width);
+	return 0;
+}
+
+/**
+ * xilinx_scaler_bridge_get_output_fmts - output formats supported by scaler
+ * @bridge: bridge instance
+ * @fmts: Pointer to be updated with formats information
+ * @count: count of video bus formats
+ *
+ * This function provides the output video formats information scaler
+ * Return: 0 on success.
+ */
+static int xilinx_scaler_bridge_get_output_fmts(struct xlnx_bridge *bridge,
+						const u32 **fmts, u32 *count)
+{
+	*fmts = xilinx_scaler_video_fmts;
+	*count = ARRAY_SIZE(xilinx_scaler_video_fmts);
+	return 0;
+}
+
+static const struct xscaler_feature xlnx_scaler_v2_2 = {
+	.flags = XSCALER_HPHASE_FIX,
+};
+
+static const struct xscaler_feature xlnx_scaler = {
+	.flags = 0,
+};
+
+static const struct of_device_id xilinx_scaler_of_match[] = {
+	{ .compatible = "xlnx,vpss-scaler",
+		.data = &xlnx_scaler},
+	{ .compatible = "xlnx,vpss-scaler-2.2",
+		.data = &xlnx_scaler_v2_2},
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, xilinx_scaler_of_match);
+
+static int xilinx_scaler_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct xilinx_scaler *scaler;
+	const struct of_device_id *match;
+	struct device_node *node = pdev->dev.of_node;
+	int ret;
+
+	scaler = devm_kzalloc(dev, sizeof(*scaler), GFP_KERNEL);
+	if (!scaler)
+		return -ENOMEM;
+	scaler->dev = dev;
+
+	match = of_match_node(xilinx_scaler_of_match, node);
+	if (!match)
+		return -ENODEV;
+
+	scaler->cfg = match->data;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	scaler->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(scaler->base)) {
+		dev_err(dev, "failed to remap io region\n");
+		return -ENOMEM;
+	}
+	platform_set_drvdata(pdev, scaler);
+
+	ret = xilinx_scaler_parse_of(scaler);
+	if (ret < 0) {
+		dev_info(scaler->dev, "parse_of failed\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(scaler->ctrl_clk);
+	if (ret) {
+		dev_err(scaler->dev, "unable to enable axi lite clk %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(scaler->axis_clk);
+	if (ret) {
+		dev_err(scaler->dev, "unable to enable video clk %d\n", ret);
+		goto err_ctrl_clk;
+	}
+
+	scaler->max_num_phases = XSCALER_MAX_PHASES;
+
+	/* Reset the Global IP Reset through a GPIO */
+	gpiod_set_value_cansleep(scaler->rst_gpio, XSCALER_RESET_DEASSERT);
+	xilinx_scaler_reset(scaler);
+
+	scaler->bridge.enable = &xilinx_scaler_bridge_enable;
+	scaler->bridge.disable = &xilinx_scaler_bridge_disable;
+	scaler->bridge.set_input = &xilinx_scaler_bridge_set_input;
+	scaler->bridge.get_input_fmts = &xilinx_scaler_bridge_get_input_fmts;
+	scaler->bridge.set_output = &xilinx_scaler_bridge_set_output;
+	scaler->bridge.get_output_fmts = &xilinx_scaler_bridge_get_output_fmts;
+	scaler->bridge.of_node = dev->of_node;
+
+	ret = xlnx_bridge_register(&scaler->bridge);
+	if (ret) {
+		dev_info(scaler->dev, "Bridge registration failed\n");
+		goto err_axis_clk;
+	}
+	dev_info(scaler->dev, "xlnx drm scaler experimental driver probed\n");
+
+	return 0;
+
+err_axis_clk:
+	clk_disable_unprepare(scaler->axis_clk);
+err_ctrl_clk:
+	clk_disable_unprepare(scaler->ctrl_clk);
+	return ret;
+}
+
+static int xilinx_scaler_remove(struct platform_device *pdev)
+{
+	struct xilinx_scaler *scaler = platform_get_drvdata(pdev);
+
+	xlnx_bridge_unregister(&scaler->bridge);
+	clk_disable_unprepare(scaler->axis_clk);
+	clk_disable_unprepare(scaler->ctrl_clk);
+	return 0;
+}
+
+static struct platform_driver scaler_bridge_driver = {
+	.probe = xilinx_scaler_probe,
+	.remove = xilinx_scaler_remove,
+	.driver = {
+		.name = "xlnx,scaler-bridge",
+		.of_match_table = xilinx_scaler_of_match,
+	},
+};
+
+module_platform_driver(scaler_bridge_driver);
+
+MODULE_AUTHOR("Venkateshwar Rao <vgannava@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx FPGA SCALER Bridge Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_sdi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_sdi.c
@@ -0,0 +1,1448 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA SDI Tx Subsystem driver.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Contacts: Saurabh Sengar <saurabhs@xilinx.com>
+ */
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_probe_helper.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/component.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <media/hdr-ctrls.h>
+#include <video/videomode.h>
+#include "xlnx_sdi_modes.h"
+#include "xlnx_sdi_timing.h"
+
+#include "xlnx_bridge.h"
+
+/* SDI register offsets */
+#define XSDI_TX_RST_CTRL		0x00
+#define XSDI_TX_MDL_CTRL		0x04
+#define XSDI_TX_GLBL_IER		0x0C
+#define XSDI_TX_ISR_STAT		0x10
+#define XSDI_TX_IER_STAT		0x14
+#define XSDI_TX_ST352_LINE		0x18
+#define XSDI_TX_ST352_DATA_CH0		0x1C
+#define XSDI_TX_VER			0x3C
+#define XSDI_TX_SYS_CFG			0x40
+#define XSDI_TX_STS_SB_TDATA		0x60
+#define XSDI_TX_AXI4S_STS1		0x68
+#define XSDI_TX_AXI4S_STS2		0x6C
+#define XSDI_TX_ST352_DATA_DS2		0x70
+
+/* MODULE_CTRL register masks */
+#define XSDI_TX_CTRL_M			BIT(7)
+#define XSDI_TX_CTRL_INS_CRC		BIT(12)
+#define XSDI_TX_CTRL_INS_ST352		BIT(13)
+#define XSDI_TX_CTRL_OVR_ST352		BIT(14)
+#define XSDI_TX_CTRL_INS_SYNC_BIT	BIT(16)
+#define XSDI_TX_CTRL_USE_ANC_IN		BIT(18)
+#define XSDI_TX_CTRL_INS_LN		BIT(19)
+#define XSDI_TX_CTRL_INS_EDH		BIT(20)
+#define XSDI_TX_CTRL_MODE		0x7
+#define XSDI_TX_CTRL_MUX		0x7
+#define XSDI_TX_CTRL_MODE_SHIFT		4
+#define XSDI_TX_CTRL_M_SHIFT		7
+#define XSDI_TX_CTRL_MUX_SHIFT		8
+#define XSDI_TX_CTRL_ST352_F2_EN_SHIFT	15
+#define XSDI_TX_CTRL_420_BIT		BIT(21)
+#define XSDI_TX_CTRL_INS_ST352_CHROMA	BIT(23)
+#define XSDI_TX_CTRL_USE_DS2_3GA	BIT(24)
+
+/* TX_ST352_LINE register masks */
+#define XSDI_TX_ST352_LINE_MASK		GENMASK(10, 0)
+#define XSDI_TX_ST352_LINE_F2_SHIFT	16
+
+/* ISR STAT register masks */
+#define XSDI_GTTX_RSTDONE_INTR		BIT(0)
+#define XSDI_TX_CE_ALIGN_ERR_INTR	BIT(1)
+#define XSDI_TX_VSYNC_INTR		BIT(2)
+#define XSDI_AXI4S_VID_LOCK_INTR	BIT(8)
+#define XSDI_OVERFLOW_INTR		BIT(9)
+#define XSDI_UNDERFLOW_INTR		BIT(10)
+#define XSDI_IER_EN_MASK		(XSDI_GTTX_RSTDONE_INTR | \
+					 XSDI_TX_CE_ALIGN_ERR_INTR | \
+					 XSDI_TX_VSYNC_INTR | \
+					 XSDI_OVERFLOW_INTR | \
+					 XSDI_UNDERFLOW_INTR)
+
+/* RST_CTRL_OFFSET masks */
+#define XSDI_TX_CTRL_EN			BIT(0)
+#define XSDI_TX_BRIDGE_CTRL_EN		BIT(8)
+#define XSDI_TX_AXI4S_CTRL_EN		BIT(9)
+/* STS_SB_TX_TDATA masks */
+#define XSDI_TX_TDATA_GT_RESETDONE	BIT(2)
+
+#define XSDI_TX_MUX_SD_HD_3GA		0
+#define	XSDI_TX_MUX_3GB			1
+#define	XSDI_TX_MUX_8STREAM_6G_12G	2
+#define	XSDI_TX_MUX_4STREAM_6G		3
+#define	XSDI_TX_MUX_16STREAM_12G	4
+
+#define SDI_MAX_DATASTREAM		8
+#define PIXELS_PER_CLK			2
+#define XSDI_CH_SHIFT			29
+#define XST352_PROG_PIC			BIT(6)
+#define XST352_PROG_TRANS		BIT(7)
+#define XST352_2048_SHIFT		BIT(6)
+#define XST352_YUV420_MASK		0x03
+#define ST352_BYTE3			0x00
+
+/* Electro Optical Transfer Function */
+#define XST352_BYTE2_EOTF_MASK		GENMASK(13, 12)
+#define XST352_BYTE2_EOTF_SDRTV		0x0
+#define XST352_BYTE2_EOTF_HLG		0x1
+#define XST352_BYTE2_EOTF_SMPTE2084	0x2
+#define XST352_BYTE2_EOTF_UNKNOWN	0x3
+#define XST352_BYTE3_COLORIMETRY_HD	BIT(23)
+#define XST352_BYTE3_COLORIMETRY	BIT(21)
+
+#define ST352_BYTE4			0x01
+#define GT_TIMEOUT			50
+/* SDI modes */
+#define XSDI_MODE_HD			0
+#define	XSDI_MODE_SD			1
+#define	XSDI_MODE_3GA			2
+#define	XSDI_MODE_3GB			3
+#define	XSDI_MODE_6G			4
+#define	XSDI_MODE_12G			5
+
+#define SDI_TIMING_PARAMS_SIZE		48
+#define CLK_RATE			148500000UL
+
+/**
+ * enum payload_line_1 - Payload Ids Line 1 number
+ * @PAYLD_LN1_HD_3_6_12G:	line 1 HD,3G,6G or 12G mode value
+ * @PAYLD_LN1_SDPAL:		line 1 SD PAL mode value
+ * @PAYLD_LN1_SDNTSC:		line 1 SD NTSC mode value
+ */
+enum payload_line_1 {
+	PAYLD_LN1_HD_3_6_12G = 10,
+	PAYLD_LN1_SDPAL = 9,
+	PAYLD_LN1_SDNTSC = 13
+};
+
+/**
+ * enum payload_line_2 - Payload Ids Line 2 number
+ * @PAYLD_LN2_HD_3_6_12G:	line 2 HD,3G,6G or 12G mode value
+ * @PAYLD_LN2_SDPAL:		line 2 SD PAL mode value
+ * @PAYLD_LN2_SDNTSC:		line 2 SD NTSC mode value
+ */
+enum payload_line_2 {
+	PAYLD_LN2_HD_3_6_12G = 572,
+	PAYLD_LN2_SDPAL = 322,
+	PAYLD_LN2_SDNTSC = 276
+};
+
+/**
+ * struct xlnx_sdi - Core configuration SDI Tx subsystem device structure
+ * @encoder: DRM encoder structure
+ * @connector: DRM connector structure
+ * @dev: device structure
+ * @gt_rst_gpio: GPIO handle to reset GT phy
+ * @base: Base address of SDI subsystem
+ * @mode_flags: SDI operation mode related flags
+ * @wait_event: wait event
+ * @event_received: wait event status
+ * @enable_st352_chroma: Able to send ST352 packets in Chroma stream.
+ * @enable_anc_data: Enable/Disable Ancillary Data insertion for Audio
+ * @sdi_mode: configurable SDI mode parameter, supported values are:
+ *		0 - HD
+ *		1 - SD
+ *		2 - 3GA
+ *		3 - 3GB
+ *		4 - 6G
+ *		5 - 12G
+ * @sdi_mod_prop_val: configurable SDI mode parameter value
+ * @sdi_data_strm: configurable SDI data stream parameter
+ * @sdi_data_strm_prop_val: configurable number of SDI data streams
+ *			    value currently supported are 2, 4 and 8
+ * @sdi_420_in: Specifying input bus color format parameter to SDI
+ * @sdi_420_in_val: 1 for yuv420 and 0 for yuv422
+ * @sdi_420_out: configurable SDI out color format parameter
+ * @sdi_420_out_val: 1 for yuv420 and 0 for yuv422
+ * @is_frac_prop: configurable SDI fractional fps parameter
+ * @is_frac_prop_val: configurable SDI fractional fps parameter value
+ * @bridge: bridge structure
+ * @height_out: configurable bridge output height parameter
+ * @height_out_prop_val: configurable bridge output height parameter value
+ * @width_out: configurable bridge output width parameter
+ * @width_out_prop_val: configurable bridge output width parameter value
+ * @in_fmt: configurable bridge input media format
+ * @in_fmt_prop_val: configurable media bus format value
+ * @out_fmt: configurable bridge output media format
+ * @out_fmt_prop_val: configurable media bus format value
+ * @en_st352_c_prop: configurable ST352 payload on Chroma stream parameter
+ * @en_st352_c_val: configurable ST352 payload on Chroma parameter value
+ * @use_ds2_3ga_prop: Use DS2 instead of DS3 in 3GA mode parameter
+ * @use_ds2_3ga_val: Use DS2 instead of DS3 in 3GA mode parameter value
+ * @c_encoding: configurable color encoding
+ * @c_encoding_prop_val: 1 for UHDTV and 0 for Rec709
+ * @video_mode: current display mode
+ * @axi_clk: AXI Lite interface clock
+ * @sditx_clk: SDI Tx Clock
+ * @vidin_clk: Video Clock
+ * @qpll1_enabled: indicates qpll1 presence
+ * @picxo_enabled: indicates picxo core presence
+ * @prev_eotf: previous end of transfer function
+ */
+struct xlnx_sdi {
+	struct drm_encoder encoder;
+	struct drm_connector connector;
+	struct device *dev;
+	struct gpio_desc *gt_rst_gpio;
+	void __iomem *base;
+	u32 mode_flags;
+	wait_queue_head_t wait_event;
+	bool event_received;
+	bool enable_st352_chroma;
+	bool enable_anc_data;
+	struct drm_property *sdi_mode;
+	u32 sdi_mod_prop_val;
+	struct drm_property *sdi_data_strm;
+	u32 sdi_data_strm_prop_val;
+	struct drm_property *sdi_420_in;
+	bool sdi_420_in_val;
+	struct drm_property *sdi_420_out;
+	bool sdi_420_out_val;
+	struct drm_property *is_frac_prop;
+	bool is_frac_prop_val;
+	struct xlnx_bridge *bridge;
+	struct drm_property *height_out;
+	u32 height_out_prop_val;
+	struct drm_property *width_out;
+	u32 width_out_prop_val;
+	struct drm_property *in_fmt;
+	u32 in_fmt_prop_val;
+	struct drm_property *out_fmt;
+	u32 out_fmt_prop_val;
+	struct drm_property *en_st352_c_prop;
+	bool en_st352_c_val;
+	struct drm_property *use_ds2_3ga_prop;
+	bool use_ds2_3ga_val;
+	struct drm_property *c_encoding;
+	u32 c_encoding_prop_val;
+	struct drm_display_mode video_mode;
+	struct clk *axi_clk;
+	struct clk *sditx_clk;
+	struct clk *vidin_clk;
+	bool qpll1_enabled;
+	bool picxo_enabled;
+	u8 prev_eotf;
+};
+
+#define connector_to_sdi(c) container_of(c, struct xlnx_sdi, connector)
+#define encoder_to_sdi(e) container_of(e, struct xlnx_sdi, encoder)
+
+static inline void xlnx_sdi_writel(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static inline u32 xlnx_sdi_readl(void __iomem *base, int offset)
+{
+	return readl(base + offset);
+}
+
+/**
+ * xlnx_sdi_en_axi4s - Enable SDI Tx AXI4S-to-Video core
+ * @sdi:	Pointer to SDI Tx structure
+ *
+ * This function enables the SDI Tx AXI4S-to-Video core.
+ */
+static void xlnx_sdi_en_axi4s(struct xlnx_sdi *sdi)
+{
+	u32 data;
+
+	data = xlnx_sdi_readl(sdi->base, XSDI_TX_RST_CTRL);
+	data |= XSDI_TX_AXI4S_CTRL_EN;
+	xlnx_sdi_writel(sdi->base, XSDI_TX_RST_CTRL, data);
+}
+
+/**
+ * xlnx_sdi_en_bridge - Enable SDI Tx bridge
+ * @sdi:	Pointer to SDI Tx structure
+ *
+ * This function enables the SDI Tx bridge.
+ */
+static void xlnx_sdi_en_bridge(struct xlnx_sdi *sdi)
+{
+	u32 data;
+
+	data = xlnx_sdi_readl(sdi->base, XSDI_TX_RST_CTRL);
+	data |= XSDI_TX_BRIDGE_CTRL_EN;
+	xlnx_sdi_writel(sdi->base, XSDI_TX_RST_CTRL, data);
+}
+
+/**
+ * xlnx_sdi_gt_reset - Reset cores through gpio
+ * @sdi: Pointer to SDI Tx structure
+ *
+ * This function resets the GT phy core.
+ */
+static void xlnx_sdi_gt_reset(struct xlnx_sdi *sdi)
+{
+	gpiod_set_value(sdi->gt_rst_gpio, 1);
+	gpiod_set_value(sdi->gt_rst_gpio, 0);
+	/* delay added to get vtc_en signal */
+	mdelay(5);
+}
+
+/**
+ * xlnx_sdi_set_eotf - Set eotf field in payload
+ * @sdi: Pointer to SDI Tx structure
+ *
+ * This function parse the hdr metadata and sets
+ * eotf and colorimetry fields of payload.
+ */
+static void xlnx_sdi_set_eotf(struct xlnx_sdi *sdi)
+{
+	struct hdmi_drm_infoframe frame;
+	struct drm_connector_state *state = sdi->connector.state;
+	u32 payload, i;
+	int ret;
+	u8 eotf, colori;
+
+	ret = drm_hdmi_infoframe_set_gen_hdr_metadata(&frame, state);
+	if (ret)
+		return;
+
+	eotf = (__u8)frame.eotf;
+
+	if (sdi->prev_eotf == eotf || eotf > XST352_BYTE2_EOTF_UNKNOWN)
+		return;
+
+	switch (eotf) {
+	case V4L2_EOTF_BT_2100_HLG:
+		eotf = XST352_BYTE2_EOTF_HLG;
+		break;
+	case V4L2_EOTF_TRADITIONAL_GAMMA_SDR:
+		eotf = XST352_BYTE2_EOTF_SDRTV;
+		break;
+	case V4L2_EOTF_SMPTE_ST2084:
+		eotf = XST352_BYTE2_EOTF_SMPTE2084;
+		break;
+	}
+
+	colori = sdi->c_encoding_prop_val;
+	payload = xlnx_sdi_readl(sdi->base, XSDI_TX_ST352_DATA_CH0);
+
+	/*
+	 * For HD mode, bit 23 and 20 of payload represents
+	 * colorimetry as per SMPTE 292-1:2018 Sec 9.5.
+	 * For other modes, its bit 21 and 20.
+	 * For BT709 & BT2020 - bit 20 is always zero
+	 */
+	if (sdi->sdi_mod_prop_val == XSDI_MODE_HD) {
+		payload &= ~(XST352_BYTE2_EOTF_MASK |
+			     XST352_BYTE3_COLORIMETRY_HD);
+		payload |= FIELD_PREP(XST352_BYTE2_EOTF_MASK, eotf) |
+			FIELD_PREP(XST352_BYTE3_COLORIMETRY_HD, colori);
+	} else {
+		payload &= ~(XST352_BYTE2_EOTF_MASK |
+			     XST352_BYTE3_COLORIMETRY);
+		payload |= FIELD_PREP(XST352_BYTE2_EOTF_MASK, eotf) |
+			FIELD_PREP(XST352_BYTE3_COLORIMETRY, colori);
+	}
+
+	dev_dbg(sdi->dev, "payload = 0x%x, eotf = %d\n", payload, eotf);
+	for (i = 0; i < sdi->sdi_data_strm_prop_val / 2; i++)
+		xlnx_sdi_writel(sdi->base,
+				(XSDI_TX_ST352_DATA_CH0 + (i * 4)), payload);
+	sdi->prev_eotf = eotf;
+}
+
+/**
+ * xlnx_sdi_irq_handler - SDI Tx interrupt
+ * @irq:	irq number
+ * @data:	irq data
+ *
+ * Return: IRQ_HANDLED for all cases.
+ *
+ * This is the compact GT ready interrupt.
+ */
+static irqreturn_t xlnx_sdi_irq_handler(int irq, void *data)
+{
+	struct xlnx_sdi *sdi = (struct xlnx_sdi *)data;
+	u32 reg;
+
+	reg = xlnx_sdi_readl(sdi->base, XSDI_TX_ISR_STAT);
+
+	if (reg & XSDI_TX_VSYNC_INTR)
+		xlnx_sdi_set_eotf(sdi);
+	if (reg & XSDI_GTTX_RSTDONE_INTR)
+		dev_dbg(sdi->dev, "GT reset interrupt received\n");
+	if (reg & XSDI_TX_CE_ALIGN_ERR_INTR)
+		dev_err_ratelimited(sdi->dev, "SDI SD CE align error\n");
+	if (reg & XSDI_OVERFLOW_INTR)
+		dev_err_ratelimited(sdi->dev, "AXI-4 Stream Overflow error\n");
+	if (reg & XSDI_UNDERFLOW_INTR)
+		dev_err_ratelimited(sdi->dev, "AXI-4 Stream Underflow error\n");
+	xlnx_sdi_writel(sdi->base, XSDI_TX_ISR_STAT,
+			reg & ~(XSDI_AXI4S_VID_LOCK_INTR));
+
+	reg = xlnx_sdi_readl(sdi->base, XSDI_TX_STS_SB_TDATA);
+	if (reg & XSDI_TX_TDATA_GT_RESETDONE) {
+		sdi->event_received = true;
+		wake_up_interruptible(&sdi->wait_event);
+	}
+	return IRQ_HANDLED;
+}
+
+/**
+ * xlnx_sdi_set_payload_line - set ST352 packet line number
+ * @sdi:	Pointer to SDI Tx structure
+ * @line_1:	line number used to insert st352 packet for field 1.
+ * @line_2:	line number used to insert st352 packet for field 2.
+ *
+ * This function set 352 packet line number.
+ */
+static void xlnx_sdi_set_payload_line(struct xlnx_sdi *sdi,
+				      u32 line_1, u32 line_2)
+{
+	u32 data;
+
+	data = ((line_1 & XSDI_TX_ST352_LINE_MASK) |
+		((line_2 & XSDI_TX_ST352_LINE_MASK) <<
+		XSDI_TX_ST352_LINE_F2_SHIFT));
+
+	xlnx_sdi_writel(sdi->base, XSDI_TX_ST352_LINE, data);
+
+	data = xlnx_sdi_readl(sdi->base, XSDI_TX_MDL_CTRL);
+	data |= (1 << XSDI_TX_CTRL_ST352_F2_EN_SHIFT);
+
+	xlnx_sdi_writel(sdi->base, XSDI_TX_MDL_CTRL, data);
+}
+
+/**
+ * xlnx_sdi_set_payload_data - set ST352 packet payload
+ * @sdi:		Pointer to SDI Tx structure
+ * @data_strm:		data stream number
+ * @payload:		st352 packet payload
+ *
+ * This function set ST352 payload data to corresponding stream.
+ */
+static void xlnx_sdi_set_payload_data(struct xlnx_sdi *sdi,
+				      u32 data_strm, u32 payload)
+{
+	xlnx_sdi_writel(sdi->base,
+			(XSDI_TX_ST352_DATA_CH0 + (data_strm * 4)), payload);
+
+	dev_dbg(sdi->dev, "enable_st352_chroma = %d and en_st352_c_val = %d\n",
+		sdi->enable_st352_chroma, sdi->en_st352_c_val);
+	if (sdi->enable_st352_chroma && sdi->en_st352_c_val) {
+		xlnx_sdi_writel(sdi->base,
+				(XSDI_TX_ST352_DATA_DS2 + (data_strm * 4)),
+				payload);
+	}
+}
+
+/**
+ * xlnx_sdi_set_display_disable - Disable the SDI Tx IP core enable
+ * register bit
+ * @sdi: SDI structure having the updated user parameters
+ *
+ * This function takes the SDI strucure and disables the core enable bit
+ * of core configuration register.
+ */
+static void xlnx_sdi_set_display_disable(struct xlnx_sdi *sdi)
+{
+	u32 i;
+
+	for (i = 0; i < SDI_MAX_DATASTREAM; i++)
+		xlnx_sdi_set_payload_data(sdi, i, 0);
+
+	xlnx_sdi_writel(sdi->base, XSDI_TX_GLBL_IER, 0);
+	xlnx_sdi_writel(sdi->base, XSDI_TX_RST_CTRL, 0);
+}
+
+/**
+ * xlnx_sdi_payload_config -  config the SDI payload parameters
+ * @sdi:	pointer Xilinx SDI Tx structure
+ * @mode:	display mode
+ *
+ * This function config the SDI st352 payload parameter.
+ */
+static void xlnx_sdi_payload_config(struct xlnx_sdi *sdi, u32 mode)
+{
+	u32 payload_1, payload_2;
+
+	switch (mode) {
+	case XSDI_MODE_SD:
+		payload_1 = PAYLD_LN1_SDPAL;
+		payload_2 = PAYLD_LN2_SDPAL;
+		break;
+	case XSDI_MODE_HD:
+	case XSDI_MODE_3GA:
+	case XSDI_MODE_3GB:
+	case XSDI_MODE_6G:
+	case XSDI_MODE_12G:
+		payload_1 = PAYLD_LN1_HD_3_6_12G;
+		payload_2 = PAYLD_LN2_HD_3_6_12G;
+		break;
+	default:
+		payload_1 = 0;
+		payload_2 = 0;
+		break;
+	}
+
+	xlnx_sdi_set_payload_line(sdi, payload_1, payload_2);
+}
+
+/**
+ * xlnx_sdi_set_mode -  Set mode parameters in SDI Tx
+ * @sdi:	pointer Xilinx SDI Tx structure
+ * @mode:	SDI Tx display mode
+ * @is_frac:	0 - integer 1 - fractional
+ * @mux_ptrn:	specifiy the data stream interleaving pattern to be used
+ * This function config the SDI st352 payload parameter.
+ */
+static void xlnx_sdi_set_mode(struct xlnx_sdi *sdi, u32 mode,
+			      bool is_frac, u32 mux_ptrn)
+{
+	u32 data;
+
+	xlnx_sdi_payload_config(sdi, mode);
+
+	data = xlnx_sdi_readl(sdi->base, XSDI_TX_MDL_CTRL);
+	data &= ~(XSDI_TX_CTRL_MODE << XSDI_TX_CTRL_MODE_SHIFT);
+	data &= ~(XSDI_TX_CTRL_M);
+	data &= ~(XSDI_TX_CTRL_MUX << XSDI_TX_CTRL_MUX_SHIFT);
+	data &= ~XSDI_TX_CTRL_420_BIT;
+
+	data |= (((mode & XSDI_TX_CTRL_MODE) << XSDI_TX_CTRL_MODE_SHIFT) |
+		(is_frac  << XSDI_TX_CTRL_M_SHIFT) |
+		((mux_ptrn & XSDI_TX_CTRL_MUX) << XSDI_TX_CTRL_MUX_SHIFT));
+
+	if (sdi->sdi_420_out_val)
+		data |= XSDI_TX_CTRL_420_BIT;
+	xlnx_sdi_writel(sdi->base, XSDI_TX_MDL_CTRL, data);
+}
+
+/**
+ * xlnx_sdi_set_config_parameters - Configure SDI Tx registers with parameters
+ * given from user application.
+ * @sdi: SDI structure having the updated user parameters
+ *
+ * This function takes the SDI structure having drm_property parameters
+ * configured from  user application and writes them into SDI IP registers.
+ */
+static void xlnx_sdi_set_config_parameters(struct xlnx_sdi *sdi)
+{
+	int mux_ptrn = -EINVAL;
+
+	switch (sdi->sdi_mod_prop_val) {
+	case XSDI_MODE_3GA:
+		mux_ptrn = XSDI_TX_MUX_SD_HD_3GA;
+		break;
+	case XSDI_MODE_3GB:
+		mux_ptrn = XSDI_TX_MUX_3GB;
+		break;
+	case XSDI_MODE_6G:
+		if (sdi->sdi_data_strm_prop_val == 4)
+			mux_ptrn = XSDI_TX_MUX_4STREAM_6G;
+		else if (sdi->sdi_data_strm_prop_val == 8)
+			mux_ptrn = XSDI_TX_MUX_8STREAM_6G_12G;
+		break;
+	case XSDI_MODE_12G:
+		if (sdi->sdi_data_strm_prop_val == 8)
+			mux_ptrn = XSDI_TX_MUX_8STREAM_6G_12G;
+		break;
+	default:
+		mux_ptrn = 0;
+		break;
+	}
+	if (mux_ptrn == -EINVAL) {
+		dev_err(sdi->dev, "%d data stream not supported for %d mode",
+			sdi->sdi_data_strm_prop_val, sdi->sdi_mod_prop_val);
+		return;
+	}
+	xlnx_sdi_set_mode(sdi, sdi->sdi_mod_prop_val, sdi->is_frac_prop_val,
+			  mux_ptrn);
+}
+
+/**
+ * xlnx_sdi_atomic_set_property - implementation of drm_connector_funcs
+ * set_property invoked by IOCTL call to DRM_IOCTL_MODE_OBJ_SETPROPERTY
+ *
+ * @connector: pointer Xilinx SDI connector
+ * @state: DRM connector state
+ * @property: pointer to the drm_property structure
+ * @val: SDI parameter value that is configured from user application
+ *
+ * This function takes a drm_property name and value given from user application
+ * and update the SDI structure property varabiles with the values.
+ * These values are later used to configure the SDI Rx IP.
+ *
+ * Return: 0 on success OR -EINVAL if setting property fails
+ */
+static int
+xlnx_sdi_atomic_set_property(struct drm_connector *connector,
+			     struct drm_connector_state *state,
+			     struct drm_property *property, uint64_t val)
+{
+	struct xlnx_sdi *sdi = connector_to_sdi(connector);
+
+	if (property == sdi->sdi_mode)
+		sdi->sdi_mod_prop_val = (unsigned int)val;
+	else if (property == sdi->sdi_data_strm)
+		sdi->sdi_data_strm_prop_val = (unsigned int)val;
+	else if (property == sdi->sdi_420_in)
+		sdi->sdi_420_in_val = val;
+	else if (property == sdi->sdi_420_out)
+		sdi->sdi_420_out_val = val;
+	else if (property == sdi->is_frac_prop)
+		sdi->is_frac_prop_val = !!val;
+	else if (property == sdi->height_out)
+		sdi->height_out_prop_val = (unsigned int)val;
+	else if (property == sdi->width_out)
+		sdi->width_out_prop_val = (unsigned int)val;
+	else if (property == sdi->in_fmt)
+		sdi->in_fmt_prop_val = (unsigned int)val;
+	else if (property == sdi->out_fmt)
+		sdi->out_fmt_prop_val = (unsigned int)val;
+	else if (property == sdi->en_st352_c_prop)
+		sdi->en_st352_c_val = !!val;
+	else if (property == sdi->use_ds2_3ga_prop)
+		sdi->use_ds2_3ga_val = !!val;
+	else if (property == sdi->c_encoding)
+		sdi->c_encoding_prop_val = val;
+	else
+		return -EINVAL;
+	return 0;
+}
+
+static int
+xlnx_sdi_atomic_get_property(struct drm_connector *connector,
+			     const struct drm_connector_state *state,
+			     struct drm_property *property, uint64_t *val)
+{
+	struct xlnx_sdi *sdi = connector_to_sdi(connector);
+
+	if (property == sdi->sdi_mode)
+		*val = sdi->sdi_mod_prop_val;
+	else if (property == sdi->sdi_data_strm)
+		*val =  sdi->sdi_data_strm_prop_val;
+	else if (property == sdi->sdi_420_in)
+		*val = sdi->sdi_420_in_val;
+	else if (property == sdi->sdi_420_out)
+		*val = sdi->sdi_420_out_val;
+	else if (property == sdi->is_frac_prop)
+		*val =  sdi->is_frac_prop_val;
+	else if (property == sdi->height_out)
+		*val = sdi->height_out_prop_val;
+	else if (property == sdi->width_out)
+		*val = sdi->width_out_prop_val;
+	else if (property == sdi->in_fmt)
+		*val = sdi->in_fmt_prop_val;
+	else if (property == sdi->out_fmt)
+		*val = sdi->out_fmt_prop_val;
+	else if (property == sdi->en_st352_c_prop)
+		*val =  sdi->en_st352_c_val;
+	else if (property == sdi->use_ds2_3ga_prop)
+		*val =  sdi->use_ds2_3ga_val;
+	else if (property == sdi->c_encoding)
+		*val = sdi->c_encoding_prop_val;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * xlnx_sdi_get_mode_id - Search for a video mode in the supported modes table
+ *
+ * @mode: mode being searched
+ *
+ * Return: mode id if mode is found OR -EINVAL otherwise
+ */
+static int xlnx_sdi_get_mode_id(struct drm_display_mode *mode)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(xlnx_sdi_modes); i++)
+		if (xlnx_sdi_modes[i].mode.htotal == mode->htotal &&
+		    xlnx_sdi_modes[i].mode.vtotal == mode->vtotal &&
+		    xlnx_sdi_modes[i].mode.clock == mode->clock &&
+		    xlnx_sdi_modes[i].mode.flags == mode->flags)
+			return i;
+	return -EINVAL;
+}
+
+/**
+ * xlnx_sdi_drm_add_modes - Adds SDI supported modes
+ * @connector: pointer Xilinx SDI connector
+ *
+ * Return:	Count of modes added
+ *
+ * This function adds the SDI modes supported and returns its count
+ */
+static int xlnx_sdi_drm_add_modes(struct drm_connector *connector)
+{
+	int num_modes = 0;
+	u32 i;
+	struct drm_display_mode *mode;
+	struct drm_device *dev = connector->dev;
+
+	for (i = 0; i < ARRAY_SIZE(xlnx_sdi_modes); i++) {
+		const struct drm_display_mode *ptr = &xlnx_sdi_modes[i].mode;
+
+		mode = drm_mode_duplicate(dev, ptr);
+		if (mode) {
+			drm_mode_probed_add(connector, mode);
+			num_modes++;
+		}
+	}
+	return num_modes;
+}
+
+static enum drm_connector_status
+xlnx_sdi_detect(struct drm_connector *connector, bool force)
+{
+	return connector_status_connected;
+}
+
+static void xlnx_sdi_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+	connector->dev = NULL;
+}
+
+static const struct drm_connector_funcs xlnx_sdi_connector_funcs = {
+	.detect = xlnx_sdi_detect,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.destroy = xlnx_sdi_connector_destroy,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_set_property = xlnx_sdi_atomic_set_property,
+	.atomic_get_property = xlnx_sdi_atomic_get_property,
+};
+
+static struct drm_encoder *
+xlnx_sdi_best_encoder(struct drm_connector *connector)
+{
+	return &(connector_to_sdi(connector)->encoder);
+}
+
+static int xlnx_sdi_get_modes(struct drm_connector *connector)
+{
+	return xlnx_sdi_drm_add_modes(connector);
+}
+
+static int xlnx_sdi_mode_valid(struct drm_connector *connector,
+			       struct drm_display_mode *mode)
+{
+	if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+		mode->vdisplay /= 2;
+
+	return MODE_OK;
+}
+
+static struct drm_connector_helper_funcs xlnx_sdi_connector_helper_funcs = {
+	.get_modes = xlnx_sdi_get_modes,
+	.best_encoder = xlnx_sdi_best_encoder,
+	.mode_valid = xlnx_sdi_mode_valid,
+};
+
+/**
+ * xlnx_sdi_drm_connector_create_property -  create SDI connector properties
+ *
+ * @base_connector: pointer to Xilinx SDI connector
+ *
+ * This function takes the xilinx SDI connector component and defines
+ * the drm_property variables with their default values.
+ */
+static void
+xlnx_sdi_drm_connector_create_property(struct drm_connector *base_connector)
+{
+	struct drm_device *dev = base_connector->dev;
+	struct xlnx_sdi *sdi  = connector_to_sdi(base_connector);
+
+	sdi->is_frac_prop = drm_property_create_bool(dev, 0, "is_frac");
+	sdi->sdi_mode = drm_property_create_range(dev, 0,
+						  "sdi_mode", 0, 5);
+	sdi->sdi_data_strm = drm_property_create_range(dev, 0,
+						       "sdi_data_stream", 2, 8);
+	sdi->sdi_420_in = drm_property_create_bool(dev, 0, "sdi_420_in");
+	sdi->sdi_420_out = drm_property_create_bool(dev, 0, "sdi_420_out");
+	sdi->height_out = drm_property_create_range(dev, 0,
+						    "height_out", 2, 4096);
+	sdi->width_out = drm_property_create_range(dev, 0,
+						   "width_out", 2, 4096);
+	sdi->in_fmt = drm_property_create_range(dev, 0,
+						"in_fmt", 0, 16384);
+	sdi->out_fmt = drm_property_create_range(dev, 0,
+						 "out_fmt", 0, 16384);
+	if (sdi->enable_st352_chroma) {
+		sdi->en_st352_c_prop = drm_property_create_bool(dev, 0,
+								"en_st352_c");
+		sdi->use_ds2_3ga_prop = drm_property_create_bool(dev, 0,
+								 "use_ds2_3ga");
+	}
+	sdi->c_encoding = drm_property_create_bool(dev, 0, "c_encoding");
+}
+
+/**
+ * xlnx_sdi_drm_connector_attach_property -  attach SDI connector
+ * properties
+ *
+ * @base_connector: pointer to Xilinx SDI connector
+ */
+static void
+xlnx_sdi_drm_connector_attach_property(struct drm_connector *base_connector)
+{
+	struct xlnx_sdi *sdi = connector_to_sdi(base_connector);
+	struct drm_mode_object *obj = &base_connector->base;
+
+	if (sdi->sdi_mode)
+		drm_object_attach_property(obj, sdi->sdi_mode, 0);
+
+	if (sdi->sdi_data_strm)
+		drm_object_attach_property(obj, sdi->sdi_data_strm, 0);
+
+	if (sdi->sdi_420_in)
+		drm_object_attach_property(obj, sdi->sdi_420_in, 0);
+
+	if (sdi->sdi_420_out)
+		drm_object_attach_property(obj, sdi->sdi_420_out, 0);
+
+	if (sdi->is_frac_prop)
+		drm_object_attach_property(obj, sdi->is_frac_prop, 0);
+
+	if (sdi->height_out)
+		drm_object_attach_property(obj, sdi->height_out, 0);
+
+	if (sdi->width_out)
+		drm_object_attach_property(obj, sdi->width_out, 0);
+
+	if (sdi->in_fmt)
+		drm_object_attach_property(obj, sdi->in_fmt, 0);
+
+	if (sdi->out_fmt)
+		drm_object_attach_property(obj, sdi->out_fmt, 0);
+
+	if (sdi->en_st352_c_prop)
+		drm_object_attach_property(obj, sdi->en_st352_c_prop, 0);
+
+	if (sdi->use_ds2_3ga_prop)
+		drm_object_attach_property(obj, sdi->use_ds2_3ga_prop, 0);
+
+	if (sdi->c_encoding)
+		drm_object_attach_property(obj, sdi->c_encoding, 0);
+
+	drm_object_attach_property(obj,
+				   base_connector->dev->mode_config.gen_hdr_output_metadata_property, 0);
+}
+
+static int xlnx_sdi_create_connector(struct drm_encoder *encoder)
+{
+	struct xlnx_sdi *sdi = encoder_to_sdi(encoder);
+	struct drm_connector *connector = &sdi->connector;
+	int ret;
+
+	connector->interlace_allowed = true;
+	connector->doublescan_allowed = true;
+
+	ret = drm_connector_init(encoder->dev, connector,
+				 &xlnx_sdi_connector_funcs,
+				 DRM_MODE_CONNECTOR_Unknown);
+	if (ret) {
+		dev_err(sdi->dev, "Failed to initialize connector with drm\n");
+		return ret;
+	}
+
+	drm_connector_helper_add(connector, &xlnx_sdi_connector_helper_funcs);
+	drm_connector_register(connector);
+	drm_connector_attach_encoder(connector, encoder);
+	xlnx_sdi_drm_connector_create_property(connector);
+	xlnx_sdi_drm_connector_attach_property(connector);
+
+	/* Fill out the supported EOTFs */
+	connector->hdr_sink_metadata.hdmi_type1.eotf |=
+		BIT(V4L2_EOTF_BT_2100_HLG) |
+		BIT(V4L2_EOTF_TRADITIONAL_GAMMA_SDR) |
+		BIT(V4L2_EOTF_SMPTE_ST2084);
+
+	return 0;
+}
+
+/**
+ * xlnx_sdi_set_display_enable - Enables the SDI Tx IP core enable
+ * register bit
+ * @sdi: SDI structure having the updated user parameters
+ *
+ * This function takes the SDI strucure and enables the core enable bit
+ * of core configuration register.
+ */
+static void xlnx_sdi_set_display_enable(struct xlnx_sdi *sdi)
+{
+	u32 data;
+
+	data = xlnx_sdi_readl(sdi->base, XSDI_TX_RST_CTRL);
+	data |= XSDI_TX_CTRL_EN;
+	xlnx_sdi_writel(sdi->base, XSDI_TX_RST_CTRL, data);
+}
+
+/**
+ * xlnx_sdi_calc_st352_payld -  calculate the st352 payload
+ *
+ * @sdi: pointer to SDI Tx structure
+ * @mode: DRM display mode
+ *
+ * This function calculates the st352 payload to be configured.
+ * Please refer to SMPTE ST352 documents for it.
+ * Return:	return st352 payload
+ */
+static u32 xlnx_sdi_calc_st352_payld(struct xlnx_sdi *sdi,
+				     struct drm_display_mode *mode)
+{
+	u8 byt1, byt2;
+	u16 is_p;
+	int id;
+	u32 sdi_mode = sdi->sdi_mod_prop_val;
+	bool is_frac = sdi->is_frac_prop_val;
+	u32 byt3 = ST352_BYTE3;
+
+	id = xlnx_sdi_get_mode_id(mode);
+	dev_dbg(sdi->dev, "mode id: %d\n", id);
+	if (mode->hdisplay == 2048 || mode->hdisplay == 4096)
+		byt3 |= XST352_2048_SHIFT;
+	if (sdi->sdi_420_in_val)
+		byt3 |= XST352_YUV420_MASK;
+
+	/* byte 2 calculation */
+	is_p = !(mode->flags & DRM_MODE_FLAG_INTERLACE);
+	byt2 = xlnx_sdi_modes[id].st352_byt2[is_frac];
+	if (sdi_mode == XSDI_MODE_3GB ||
+	    (mode->flags & DRM_MODE_FLAG_DBLSCAN) || is_p)
+		byt2 |= XST352_PROG_PIC;
+	if (is_p && mode->vtotal >= 1125)
+		byt2 |= XST352_PROG_TRANS;
+
+	/* byte 1 calculation */
+	byt1 = xlnx_sdi_modes[id].st352_byt1[sdi_mode];
+
+	return (ST352_BYTE4 << 24 | byt3 << 16 | byt2 << 8 | byt1);
+}
+
+static void xlnx_sdi_setup(struct xlnx_sdi *sdi)
+{
+	u32 reg;
+
+	dev_dbg(sdi->dev, "%s\n", __func__);
+
+	reg = xlnx_sdi_readl(sdi->base, XSDI_TX_MDL_CTRL);
+	reg |= XSDI_TX_CTRL_INS_CRC | XSDI_TX_CTRL_INS_ST352 |
+		XSDI_TX_CTRL_OVR_ST352 | XSDI_TX_CTRL_INS_SYNC_BIT |
+		XSDI_TX_CTRL_INS_EDH;
+
+	if (sdi->enable_anc_data)
+		reg |= XSDI_TX_CTRL_USE_ANC_IN;
+
+	if (sdi->enable_st352_chroma) {
+		if (sdi->en_st352_c_val) {
+			reg |= XSDI_TX_CTRL_INS_ST352_CHROMA;
+			if (sdi->use_ds2_3ga_val)
+				reg |= XSDI_TX_CTRL_USE_DS2_3GA;
+			else
+				reg &= ~XSDI_TX_CTRL_USE_DS2_3GA;
+		} else {
+			reg &= ~XSDI_TX_CTRL_INS_ST352_CHROMA;
+			reg &= ~XSDI_TX_CTRL_USE_DS2_3GA;
+		}
+	}
+
+	xlnx_sdi_writel(sdi->base, XSDI_TX_MDL_CTRL, reg);
+	xlnx_sdi_writel(sdi->base, XSDI_TX_IER_STAT, XSDI_IER_EN_MASK);
+	xlnx_sdi_writel(sdi->base, XSDI_TX_GLBL_IER, 1);
+	xlnx_stc_reset(sdi->base);
+}
+
+/**
+ * xlnx_sdi_encoder_atomic_mode_set -  drive the SDI timing parameters
+ *
+ * @encoder: pointer to Xilinx DRM encoder
+ * @crtc_state: DRM crtc state
+ * @connector_state: DRM connector state
+ *
+ * This function derives the SDI IP timing parameters from the timing
+ * values given to timing module.
+ */
+static void xlnx_sdi_encoder_atomic_mode_set(struct drm_encoder *encoder,
+					     struct drm_crtc_state *crtc_state,
+				  struct drm_connector_state *connector_state)
+{
+	struct xlnx_sdi *sdi = encoder_to_sdi(encoder);
+	struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+	struct videomode vm;
+	u32 payload, i;
+	u32 sditx_blank, vtc_blank;
+	unsigned long clkrate;
+	int ret;
+
+	/*
+	 * For the transceiver TX, for integer and fractional frame rate, the
+	 * PLL ref clock must be a different frequency. Other than SD mode
+	 * its 148.5MHz for an integer & 148.5/1.001 for fractional framerate.
+	 * Program clocks followed by reset, if picxo is not enabled.
+	 */
+	if (!sdi->picxo_enabled) {
+		if (sdi->is_frac_prop_val &&
+		    sdi->sdi_mod_prop_val != XSDI_MODE_SD)
+			clkrate = (CLK_RATE * 1000) / 1001;
+		else
+			clkrate = CLK_RATE;
+		ret = clk_set_rate(sdi->sditx_clk, clkrate);
+		if (ret)
+			dev_err(sdi->dev, "failed to set clk rate = %lu\n",
+				clkrate);
+		clkrate = clk_get_rate(sdi->sditx_clk);
+		dev_info(sdi->dev, "clkrate = %lu is_frac = %d\n", clkrate,
+			 sdi->is_frac_prop_val);
+		/*
+		 * Delay required to get QPLL1 lock as per the si5328
+		 * datasheet
+		 */
+		mdelay(50);
+		xlnx_sdi_gt_reset(sdi);
+	}
+
+	/* Set timing parameters as per bridge output parameters */
+	xlnx_bridge_set_input(sdi->bridge, adjusted_mode->hdisplay,
+			      adjusted_mode->vdisplay, sdi->in_fmt_prop_val);
+	xlnx_bridge_set_output(sdi->bridge, sdi->width_out_prop_val,
+			       sdi->height_out_prop_val, sdi->out_fmt_prop_val);
+	xlnx_bridge_enable(sdi->bridge);
+
+	if (sdi->bridge) {
+		for (i = 0; i < ARRAY_SIZE(xlnx_sdi_modes); i++) {
+			if (xlnx_sdi_modes[i].mode.hdisplay ==
+			    sdi->width_out_prop_val &&
+			    xlnx_sdi_modes[i].mode.vdisplay ==
+			    sdi->height_out_prop_val &&
+			    adjusted_mode->flags == xlnx_sdi_modes[i].mode.flags &&
+			    drm_mode_vrefresh(&xlnx_sdi_modes[i].mode) ==
+			    drm_mode_vrefresh(adjusted_mode)) {
+				memcpy((char *)adjusted_mode +
+				       offsetof(struct drm_display_mode,
+						clock),
+				       &xlnx_sdi_modes[i].mode.clock,
+				       SDI_TIMING_PARAMS_SIZE);
+				break;
+			}
+		}
+	}
+
+	xlnx_sdi_setup(sdi);
+	xlnx_sdi_set_config_parameters(sdi);
+
+	/* set st352 payloads */
+	payload = xlnx_sdi_calc_st352_payld(sdi, adjusted_mode);
+	dev_dbg(sdi->dev, "payload : %0x\n", payload);
+
+	for (i = 0; i < sdi->sdi_data_strm_prop_val / 2; i++) {
+		if (sdi->sdi_mod_prop_val == XSDI_MODE_3GB)
+			payload |= (i << 1) << XSDI_CH_SHIFT;
+		xlnx_sdi_set_payload_data(sdi, i, payload);
+	}
+
+	/* UHDSDI is fixed 2 pixels per clock, horizontal timings div by 2 */
+	vm.hactive = adjusted_mode->hdisplay / PIXELS_PER_CLK;
+	vm.hfront_porch = (adjusted_mode->hsync_start -
+			  adjusted_mode->hdisplay) / PIXELS_PER_CLK;
+	vm.hback_porch = (adjusted_mode->htotal -
+			 adjusted_mode->hsync_end) / PIXELS_PER_CLK;
+	vm.hsync_len = (adjusted_mode->hsync_end -
+		       adjusted_mode->hsync_start) / PIXELS_PER_CLK;
+
+	vm.vactive = adjusted_mode->vdisplay;
+	if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) {
+		vm.vfront_porch = adjusted_mode->vsync_start / 2 -
+				  adjusted_mode->vdisplay;
+		vm.vback_porch = (adjusted_mode->vtotal -
+				  adjusted_mode->vsync_end) / 2;
+		vm.vsync_len = (adjusted_mode->vsync_end -
+				adjusted_mode->vsync_start) / 2;
+	} else {
+		vm.vfront_porch = adjusted_mode->vsync_start -
+				  adjusted_mode->vdisplay;
+		vm.vback_porch = adjusted_mode->vtotal -
+				 adjusted_mode->vsync_end;
+		vm.vsync_len = adjusted_mode->vsync_end -
+			       adjusted_mode->vsync_start;
+	}
+
+	vm.flags = 0;
+	if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE)
+		vm.flags |= DISPLAY_FLAGS_INTERLACED;
+	if (adjusted_mode->flags & DRM_MODE_FLAG_PHSYNC)
+		vm.flags |= DISPLAY_FLAGS_HSYNC_LOW;
+	if (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC)
+		vm.flags |= DISPLAY_FLAGS_VSYNC_LOW;
+
+	do {
+		sditx_blank = (adjusted_mode->hsync_start -
+			       adjusted_mode->hdisplay) +
+			      (adjusted_mode->hsync_end -
+			       adjusted_mode->hsync_start) +
+			      (adjusted_mode->htotal -
+			       adjusted_mode->hsync_end);
+
+		vtc_blank = (vm.hfront_porch + vm.hback_porch +
+			     vm.hsync_len) * PIXELS_PER_CLK;
+
+		if (vtc_blank != sditx_blank)
+			vm.hfront_porch++;
+	} while (vtc_blank < sditx_blank);
+
+	vm.pixelclock = adjusted_mode->clock * 1000;
+
+	/* parameters for sdi audio */
+	sdi->video_mode.vdisplay = adjusted_mode->vdisplay;
+	sdi->video_mode.hdisplay = adjusted_mode->hdisplay;
+	sdi->video_mode.flags = adjusted_mode->flags;
+	sdi->video_mode.htotal = adjusted_mode->htotal;
+	sdi->video_mode.vtotal = adjusted_mode->vtotal;
+	sdi->video_mode.clock = adjusted_mode->clock;
+
+	xlnx_stc_sig(sdi->base, &vm);
+}
+
+static void xlnx_sdi_commit(struct drm_encoder *encoder)
+{
+	struct xlnx_sdi *sdi = encoder_to_sdi(encoder);
+	long ret;
+
+	dev_dbg(sdi->dev, "%s\n", __func__);
+	xlnx_sdi_set_display_enable(sdi);
+	ret = wait_event_interruptible_timeout(sdi->wait_event,
+					       sdi->event_received,
+					       usecs_to_jiffies(GT_TIMEOUT));
+	if (!ret) {
+		dev_err(sdi->dev, "Timeout: GT interrupt not received\n");
+		return;
+	}
+	sdi->event_received = false;
+	/* enable sdi bridge, timing controller and Axi4s_vid_out_ctrl */
+	xlnx_sdi_en_bridge(sdi);
+	xlnx_stc_enable(sdi->base);
+	xlnx_sdi_en_axi4s(sdi);
+}
+
+static void xlnx_sdi_disable(struct drm_encoder *encoder)
+{
+	struct xlnx_sdi *sdi = encoder_to_sdi(encoder);
+
+	if (sdi->bridge)
+		xlnx_bridge_disable(sdi->bridge);
+
+	xlnx_sdi_set_display_disable(sdi);
+	xlnx_stc_disable(sdi->base);
+}
+
+static const struct drm_encoder_helper_funcs xlnx_sdi_encoder_helper_funcs = {
+	.atomic_mode_set	= xlnx_sdi_encoder_atomic_mode_set,
+	.enable			= xlnx_sdi_commit,
+	.disable		= xlnx_sdi_disable,
+};
+
+static const struct drm_encoder_funcs xlnx_sdi_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+static int xlnx_sdi_bind(struct device *dev, struct device *master,
+			 void *data)
+{
+	struct xlnx_sdi *sdi = dev_get_drvdata(dev);
+	struct drm_encoder *encoder = &sdi->encoder;
+	struct drm_device *drm_dev = data;
+	int ret;
+
+	/*
+	 * TODO: The possible CRTCs are 1 now as per current implementation of
+	 * SDI tx drivers. DRM framework can support more than one CRTCs and
+	 * SDI driver can be enhanced for that.
+	 */
+	encoder->possible_crtcs = 1;
+
+	drm_encoder_init(drm_dev, encoder, &xlnx_sdi_encoder_funcs,
+			 DRM_MODE_ENCODER_TMDS, NULL);
+
+	drm_encoder_helper_add(encoder, &xlnx_sdi_encoder_helper_funcs);
+
+	ret = xlnx_sdi_create_connector(encoder);
+	if (ret) {
+		dev_err(sdi->dev, "fail creating connector, ret = %d\n", ret);
+		drm_encoder_cleanup(encoder);
+	}
+	return ret;
+}
+
+static void xlnx_sdi_unbind(struct device *dev, struct device *master,
+			    void *data)
+{
+	struct xlnx_sdi *sdi = dev_get_drvdata(dev);
+
+	xlnx_sdi_set_display_disable(sdi);
+	xlnx_stc_disable(sdi->base);
+	drm_encoder_cleanup(&sdi->encoder);
+	drm_connector_cleanup(&sdi->connector);
+	xlnx_bridge_disable(sdi->bridge);
+}
+
+static const struct component_ops xlnx_sdi_component_ops = {
+	.bind	= xlnx_sdi_bind,
+	.unbind	= xlnx_sdi_unbind,
+};
+
+static int xlnx_sdi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct xlnx_sdi *sdi;
+	struct device_node *vpss_node;
+	int ret, irq;
+	struct device_node *ports, *port;
+	u32 nports = 0, portmask = 0;
+	unsigned long clkrate = 0;
+	enum gpiod_flags flags;
+
+	sdi = devm_kzalloc(dev, sizeof(*sdi), GFP_KERNEL);
+	if (!sdi)
+		return -ENOMEM;
+
+	sdi->dev = dev;
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	sdi->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(sdi->base)) {
+		dev_err(dev, "failed to remap io region\n");
+		return PTR_ERR(sdi->base);
+	}
+	platform_set_drvdata(pdev, sdi);
+
+	sdi->axi_clk = devm_clk_get(dev, "s_axi_aclk");
+	if (IS_ERR(sdi->axi_clk)) {
+		ret = PTR_ERR(sdi->axi_clk);
+		dev_err(dev, "failed to get s_axi_aclk %d\n", ret);
+		return ret;
+	}
+
+	sdi->sditx_clk = devm_clk_get(dev, "sdi_tx_clk");
+	if (IS_ERR(sdi->sditx_clk)) {
+		ret = PTR_ERR(sdi->sditx_clk);
+		dev_err(dev, "failed to get sdi_tx_clk %d\n", ret);
+		return ret;
+	}
+
+	sdi->vidin_clk = devm_clk_get(dev, "video_in_clk");
+	if (IS_ERR(sdi->vidin_clk)) {
+		ret = PTR_ERR(sdi->vidin_clk);
+		dev_err(dev, "failed to get video_in_clk %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(sdi->axi_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable axi_clk %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(sdi->sditx_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable sditx_clk %d\n", ret);
+		goto err_disable_axi_clk;
+	}
+
+	ret = clk_prepare_enable(sdi->vidin_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable vidin_clk %d\n", ret);
+		goto err_disable_sditx_clk;
+	}
+
+	sdi->qpll1_enabled = of_property_read_bool(sdi->dev->of_node,
+						   "xlnx,qpll1_enabled");
+
+	sdi->picxo_enabled = of_property_read_bool(sdi->dev->of_node,
+						   "xlnx,picxo_enabled");
+	dev_dbg(dev, "sdi-tx: value of qpll1_en = %d picxo_en = %d\n",
+		sdi->qpll1_enabled, sdi->picxo_enabled);
+
+	if (sdi->qpll1_enabled)
+		flags = GPIOD_OUT_LOW;
+	else
+		flags = GPIOD_OUT_HIGH;
+
+	sdi->gt_rst_gpio = devm_gpiod_get_optional(&pdev->dev, "phy-reset",
+						   flags);
+
+	if (IS_ERR(sdi->gt_rst_gpio)) {
+		ret = PTR_ERR(sdi->gt_rst_gpio);
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Unable to get phy gpio\n");
+		goto err_disable_vidin_clk;
+	}
+
+	ret = clk_set_rate(sdi->sditx_clk, CLK_RATE);
+	if (ret)
+		dev_err(sdi->dev, "failed to set clk rate = %lu\n", CLK_RATE);
+
+	clkrate = clk_get_rate(sdi->sditx_clk);
+	dev_dbg(sdi->dev, "clkrate = %lu\n", clkrate);
+
+	/* in case all "port" nodes are grouped under a "ports" node */
+	ports = of_get_child_by_name(sdi->dev->of_node, "ports");
+	if (!ports) {
+		dev_dbg(dev, "Searching for port nodes in device node.\n");
+		ports = sdi->dev->of_node;
+	}
+
+	for_each_child_of_node(ports, port) {
+		struct device_node *endpoint;
+		u32 index;
+
+		if (!port->name || of_node_cmp(port->name, "port")) {
+			dev_dbg(dev, "port name is null or node name is not port!\n");
+			continue;
+		}
+
+		endpoint = of_get_next_child(port, NULL);
+		if (!endpoint) {
+			dev_err(dev, "No remote port at %s\n", port->name);
+			of_node_put(endpoint);
+			ret = -EINVAL;
+			goto err_disable_vidin_clk;
+		}
+
+		of_node_put(endpoint);
+
+		ret = of_property_read_u32(port, "reg", &index);
+		if (ret) {
+			dev_err(dev, "reg property not present - %d\n", ret);
+			goto err_disable_vidin_clk;
+		}
+
+		portmask |= (1 << index);
+
+		nports++;
+	}
+
+	if (nports == 2 && portmask & 0x3) {
+		dev_dbg(dev, "enable ancillary port\n");
+		sdi->enable_anc_data = true;
+	} else if (nports == 1 && portmask & 0x1) {
+		dev_dbg(dev, "no ancillary port\n");
+		sdi->enable_anc_data = false;
+	} else {
+		dev_err(dev, "Incorrect dt node!\n");
+		ret = -EINVAL;
+		goto err_disable_vidin_clk;
+	}
+
+	sdi->enable_st352_chroma = of_property_read_bool(sdi->dev->of_node,
+							 "xlnx,tx-insert-c-str-st352");
+
+	/* disable interrupt */
+	xlnx_sdi_writel(sdi->base, XSDI_TX_GLBL_IER, 0);
+	irq = platform_get_irq_byname(pdev, "sdi_tx_irq");
+	if (irq < 0) {
+		/*
+		 * If there is no IRQ with this name, try to get the first
+		 * IRQ defined in the device tree.
+		 */
+		irq = platform_get_irq(pdev, 0);
+		if (irq < 0) {
+			ret = irq;
+			goto err_disable_vidin_clk;
+		}
+	}
+
+	ret = devm_request_threaded_irq(sdi->dev, irq, NULL,
+					xlnx_sdi_irq_handler, IRQF_ONESHOT,
+					dev_name(sdi->dev), sdi);
+	if (ret < 0)
+		goto err_disable_vidin_clk;
+
+	/* initialize the wait queue for GT reset event */
+	init_waitqueue_head(&sdi->wait_event);
+
+	/* Bridge support */
+	vpss_node = of_parse_phandle(sdi->dev->of_node, "xlnx,vpss", 0);
+	if (vpss_node) {
+		sdi->bridge = of_xlnx_bridge_get(vpss_node);
+		if (!sdi->bridge) {
+			dev_info(sdi->dev, "Didn't get bridge instance\n");
+			ret = -EPROBE_DEFER;
+			goto err_disable_vidin_clk;
+		}
+	}
+
+	/* video mode properties needed by audio driver are shared to audio
+	 * driver through a pointer in platform data. This will be used in
+	 * audio driver. The solution may be needed to modify/extend to avoid
+	 * probable error scenarios
+	 */
+	pdev->dev.platform_data = &sdi->video_mode;
+	/* Initialize to IP default value */
+	sdi->prev_eotf = XST352_BYTE2_EOTF_SDRTV;
+
+	ret = component_add(dev, &xlnx_sdi_component_ops);
+	if (ret < 0)
+		goto err_disable_vidin_clk;
+
+	return ret;
+
+err_disable_vidin_clk:
+	clk_disable_unprepare(sdi->vidin_clk);
+err_disable_sditx_clk:
+	clk_disable_unprepare(sdi->sditx_clk);
+err_disable_axi_clk:
+	clk_disable_unprepare(sdi->axi_clk);
+
+	return ret;
+}
+
+static int xlnx_sdi_remove(struct platform_device *pdev)
+{
+	struct xlnx_sdi *sdi = platform_get_drvdata(pdev);
+
+	component_del(&pdev->dev, &xlnx_sdi_component_ops);
+	clk_disable_unprepare(sdi->vidin_clk);
+	clk_disable_unprepare(sdi->sditx_clk);
+	clk_disable_unprepare(sdi->axi_clk);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_sdi_of_match[] = {
+	{ .compatible = "xlnx,sdi-tx"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xlnx_sdi_of_match);
+
+static struct platform_driver sdi_tx_driver = {
+	.probe = xlnx_sdi_probe,
+	.remove = xlnx_sdi_remove,
+	.driver = {
+		.name = "xlnx-sdi-tx",
+		.of_match_table = xlnx_sdi_of_match,
+	},
+};
+
+module_platform_driver(sdi_tx_driver);
+
+MODULE_AUTHOR("Saurabh Sengar <saurabhs@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx FPGA SDI Tx Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_sdi_modes.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_sdi_modes.h
@@ -0,0 +1,411 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx FPGA SDI modes timing values for various
+ * resolutions
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Contacts: Saurabh Sengar <saurabhs@xilinx.com>
+ */
+
+#ifndef _XLNX_SDI_MODES_H_
+#define _XLNX_SDI_MODES_H_
+
+/**
+ * struct xlnx_sdi_display_config - SDI supported modes structure
+ * @mode: drm display mode
+ * @st352_byt2: st352 byte 2 value
+ *		index 0 : value for integral fps
+ *		index 1 : value for fractional fps
+ * @st352_byt1: st352 byte 1 value
+ *		index 0 : value for HD mode
+ *		index 1 : value for SD mode
+ *		index 2 : value for 3GA
+ *		index 3 : value for 3GB
+ *		index 4 : value for 6G
+ *		index 5 : value for 12G
+ */
+struct xlnx_sdi_display_config {
+	struct drm_display_mode mode;
+	u8 st352_byt2[2];
+	u8 st352_byt1[6];
+};
+
+/*
+ * xlnx_sdi_modes - SDI DRM modes
+ */
+static const struct xlnx_sdi_display_config xlnx_sdi_modes[] = {
+	/* 0 - dummy, VICs start at 1 */
+	{ },
+	/* SD: 720x486i@59.94Hz */
+	{{ DRM_MODE("720x486i", DRM_MODE_TYPE_DRIVER, 13500, 720, 739,
+		   801, 858, 0, 486, 494, 500, 525, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLCLK),
+		   }, {0x7, 0x6},
+		   {0x81, 0x81, 0x81, 0x81, 0x81, 0x81} },
+	/* SD: 720x576i@50Hz */
+	{{ DRM_MODE("720x576i", DRM_MODE_TYPE_DRIVER, 13500, 720, 732,
+		   795, 864, 0, 576, 580, 586, 625, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLCLK),
+		   }, {0x9, 0x9},
+		   {0x81, 0x81, 0x81, 0x81, 0x81, 0x81} },
+	/* HD: 1280x720@25Hz */
+	{{ DRM_MODE("1280x720", DRM_MODE_TYPE_DRIVER, 74250, 1280, 2250,
+		   2990, 3960, 0, 720, 725, 730, 750, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x5, 0x5},
+		   {0x84, 0x84, 0x88, 0x84, 0x84, 0x84} },
+	/* HD: 1280x720@24Hz */
+	{{ DRM_MODE("1280x720", DRM_MODE_TYPE_DRIVER, 74250, 1280, 2250,
+		   3155, 4125, 0, 720, 725, 730, 750, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x84, 0x84, 0x88, 0x84, 0x84, 0x84} },
+	/* HD: 1280x720@30Hz */
+	 {{ DRM_MODE("1280x720", DRM_MODE_TYPE_DRIVER, 74250, 1280, 2250,
+		   2330, 3300, 0, 720, 725, 730, 750, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x84, 0x84, 0x88, 0x84, 0x84, 0x84} },
+	/* HD: 1280x720@50Hz */
+	{{ DRM_MODE("1280x720", DRM_MODE_TYPE_DRIVER, 74250, 1280, 1720,
+		   1760, 1980, 0, 720, 725, 730, 750, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x9, 0x9},
+		   {0x84, 0x84, 0x88, 0x84, 0x84, 0x84} },
+	/* HD: 1280x720@60Hz */
+	{{ DRM_MODE("1280x720", DRM_MODE_TYPE_DRIVER, 74250, 1280, 1390,
+		   1430, 1650, 0, 720, 725, 730, 750, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x84, 0x84, 0x88, 0x84, 0x84, 0x84} },
+	/* HD: 1920x1080@24Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2558,
+		   2602, 2750, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080@25Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2448,
+		   2492, 2640, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x5, 0x5},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080@30Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080i@48Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2291,
+		   2379, 2750, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x3, 0x2},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080i@50Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2448,
+		   2492, 2640, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x5, 0x5},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080i@60Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080i@59.94Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 74175, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080sf@24Hz */
+	{{ DRM_MODE("1920x1080sf", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2291,
+		   2379, 2750, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLSCAN),
+		   }, {0x3, 0x2},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080sf@25Hz */
+	{{ DRM_MODE("1920x1080sf", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2448,
+		   2492, 2640, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLSCAN),
+		   }, {0x5, 0x5},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 1920x1080sf@30Hz */
+	{{ DRM_MODE("1920x1080sf", DRM_MODE_TYPE_DRIVER, 74250, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLSCAN),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080i@48Hz */
+	{{ DRM_MODE("2048x1080i", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2377,
+		   2421, 2750, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x3, 0x2},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080i@50Hz */
+	{{ DRM_MODE("2048x1080i", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2322,
+		   2366, 2640, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x5, 0x5},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080i@60Hz */
+	{{ DRM_MODE("2048x1080i", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2114,
+		   2134, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080sf@24Hz */
+	{{ DRM_MODE("2048x1080sf", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2377,
+		   2421, 2750, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLSCAN),
+		   }, {0x3, 0x2},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080sf@25Hz */
+	{{ DRM_MODE("2048x1080sf", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2322,
+		   2366, 2640, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLSCAN),
+		   }, {0x5, 0x5},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080sf@30Hz */
+	{{ DRM_MODE("2048x1080sf", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2114,
+		   2134, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE | DRM_MODE_FLAG_DBLSCAN),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080@30Hz */
+	{{ DRM_MODE("2048x1080", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2114,
+		   2134, 2200, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080@25Hz */
+	{{ DRM_MODE("2048x1080", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2448,
+		   2492, 2640, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x5, 0x5},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* HD: 2048x1080@24Hz */
+	{{ DRM_MODE("2048x1080", DRM_MODE_TYPE_DRIVER, 74250, 2048, 2558,
+		   2602, 2750, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 1920x1080@48Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 148500, 1920, 2558,
+		   2602, 2750, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x8, 0x4},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 1920x1080@50Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 148500, 1920, 2448,
+		   2492, 2640, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x9, 0x9},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 1920x1080@60Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 148500, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 1920x1080@59.94Hz */
+	{{ DRM_MODE("1920x1080", DRM_MODE_TYPE_DRIVER, 148350, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 2048x1080@60Hz */
+	{{ DRM_MODE("2048x1080", DRM_MODE_TYPE_DRIVER, 148500, 2048, 2136,
+		   2180, 2200, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 2048x1080@50Hz */
+	{{ DRM_MODE("2048x1080", DRM_MODE_TYPE_DRIVER, 148500, 2048, 2448,
+		   2492, 2640, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x9, 0x9},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G: 2048x1080@48Hz */
+	{{ DRM_MODE("2048x1080", DRM_MODE_TYPE_DRIVER, 148500, 2048, 2558,
+		   2602, 2750, 0, 1080, 1084, 1089, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x8, 0x4},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G-B: 1920x1080i@96Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 148500, 1920, 2291,
+		   2379, 2750, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x8, 0x4},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G-B: 1920x1080i@100Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 148500, 1920, 2448,
+		   2492, 2640, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x9, 0x9},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G-B: 1920x1080i@120Hz */
+	{{ DRM_MODE("1920x1080i", DRM_MODE_TYPE_DRIVER, 148500, 1920, 2008,
+		   2052, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0xB, 0xA},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G-B: 2048x1080i@96Hz */
+	{{ DRM_MODE("2048x1080i", DRM_MODE_TYPE_DRIVER, 148500, 2048, 2377,
+		   2421, 2750, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x8, 0x4},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G-B: 2048x1080i@100Hz */
+	{{ DRM_MODE("2048x1080i", DRM_MODE_TYPE_DRIVER, 148500, 2048, 2322,
+		   2366, 2640, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0x9, 0x9},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 3G-B: 2048x1080i@120Hz */
+	{{ DRM_MODE("2048x1080i", DRM_MODE_TYPE_DRIVER, 148500, 2048, 2114,
+		   2134, 2200, 0, 1080, 1084, 1094, 1125, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC |
+		   DRM_MODE_FLAG_INTERLACE),
+		   }, {0xB, 0xA},
+		   {0x85, 0x85, 0x89, 0x8A, 0xC1, 0xC1} },
+	/* 6G: 3840x2160@29.97Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 296704, 3840, 4016,
+		   4104, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 3840x2160@30Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 297000, 3840, 4016,
+		   4104, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 3840x2160@25Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 297000, 3840, 4896,
+		   4984, 5280, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x5, 0x5},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 3840x2160@23.98Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 296704, 3840, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 3840x2160@24Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 297000, 3840, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 4096x2160@23.98 */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 296704, 4096, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 4096x2160@24Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 297000, 4096, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x3, 0x2},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 4096x2160@25Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 297000, 4096, 5064,
+		   5152, 5280, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x5, 0x5},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 4096x2160@29.97Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 296704, 4096, 4184,
+		   4272, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 6G: 4096x2160@30Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 297000, 4096, 4184,
+		   4272, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x7, 0x6},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 3840x2160@48Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 594000, 3840, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x8, 0x4},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 3840x2160@50Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 594000, 3840, 4896,
+		   4984, 5280, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x9, 0x9},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 3840x2160@59.94Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 593406, 3840, 4016,
+		   4104, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 3840x2160@60Hz */
+	{{ DRM_MODE("3840x2160", DRM_MODE_TYPE_DRIVER, 594000, 3840, 4016,
+		   4104, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 4096x2160@47.95Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 593406, 4096, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x8, 0x4},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 4096x2160@48Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 594000, 4096, 5116,
+		   5204, 5500, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x8, 0x4},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 4096x2160@50Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 594000, 4096, 5064,
+		   5152, 5280, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0x9, 0x9},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 4096x2160@59.94Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 593408, 4096, 4184,
+		   4272, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+	/* 12G: 4096x2160@60Hz */
+	{{ DRM_MODE("4096x2160", DRM_MODE_TYPE_DRIVER, 594000, 4096, 4184,
+		   4272, 4400, 0, 2160, 2168, 2178, 2250, 0,
+		   DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC),
+		   }, {0xB, 0xA},
+		   {0x98, 0x98, 0x97, 0x98, 0xC0, 0xCE} },
+};
+
+#endif /* _XLNX_SDI_MODES_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_sdi_timing.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_sdi_timing.c
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx FPGA SDI Tx timing controller driver
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Contacts: Saurabh Sengar <saurabhs@xilinx.com>
+ */
+
+#include <drm/drm_print.h>
+#include <linux/device.h>
+#include <video/videomode.h>
+#include <asm/io.h>
+#include "xlnx_sdi_timing.h"
+
+/* timing controller register offsets */
+#define XSTC_CTL	0x00
+#define XSTC_STATS	0x04
+#define XSTC_ERROR	0x08
+#define XSTC_GASIZE	0x60
+#define XSTC_GENC	0x68
+#define XSTC_GPOL	0x6c
+#define XSTC_GHSIZE	0x70
+#define XSTC_GVSIZE	0x74
+#define XSTC_GHSYNC	0x78
+#define XSTC_GVBH_F0	0x7c
+#define XSTC_GVSYNC_F0	0x80
+#define XSTC_GVSH_F0	0x84
+#define XSTC_GVBH_F1	0x88
+#define XSTC_GVSYNC_F1	0x8C
+#define XSTC_GVSH_F1	0x90
+#define XSTC_GASIZE_F1	0x94
+#define XSTC_OFFSET	0x10000
+
+/* timing controller register bit */
+#define XSTC_CTL_FIP	BIT(6)	/* field id polarity */
+#define XSTC_CTL_ACP	BIT(5)	/* active chroma polarity */
+#define XSTC_CTL_AVP	BIT(4)	/* active video polarity */
+#define XSTC_CTL_HSP	BIT(3)	/* hori sync polarity */
+#define XSTC_CTL_VSP	BIT(2)	/* vert sync polarity */
+#define XSTC_CTL_HBP	BIT(1)	/* hori blank polarity */
+#define XSTC_CTL_VBP	BIT(0)	/* vert blank polarity */
+#define XSTC_CTL_FIPSS	BIT(26)	/* field id polarity source */
+#define XSTC_CTL_ACPSS	BIT(25)	/* active chroma polarity src */
+#define XSTC_CTL_AVPSS	BIT(24)	/* active video polarity src */
+#define XSTC_CTL_HSPSS	BIT(23)	/* hori sync polarity src */
+#define XSTC_CTL_VSPSS	BIT(22)	/* vert sync polarity src */
+#define XSTC_CTL_HBPSS	BIT(21)	/* hori blank polarity src */
+#define XSTC_CTL_VBPSS	BIT(20)	/* vert blank polarity src */
+#define XSTC_CTL_VCSS	BIT(18)	/* chroma src */
+#define XSTC_CTL_VASS	BIT(17)	/* vertical offset src */
+#define XSTC_CTL_VBSS	BIT(16)	/* vertical sync end src */
+#define XSTC_CTL_VSSS	BIT(15)	/* vertical sync start src */
+#define XSTC_CTL_VFSS	BIT(14)	/* vertical active size src */
+#define XSTC_CTL_VTSS	BIT(13)	/* vertical frame size src */
+#define XSTC_CTL_HBSS	BIT(11)	/* horiz sync end src */
+#define XSTC_CTL_HSSS	BIT(10)	/* horiz sync start src */
+#define XSTC_CTL_HFSS	BIT(9)	/* horiz active size src */
+#define XSTC_CTL_HTSS	BIT(8)	/* horiz frame size src */
+#define XSTC_CTL_GE	BIT(2)	/* timing generator enable */
+#define XSTC_CTL_RU	BIT(1)	/* timing register update */
+
+/* timing generator horizontal 1 */
+#define XSTC_GH1_BPSTART_MASK	GENMASK(28, 16)
+#define XSTC_GH1_BPSTART_SHIFT	16
+#define XSTC_GH1_SYNCSTART_MASK	GENMASK(12, 0)
+/* timing generator vertical 1 (filed 0) */
+#define XSTC_GV1_BPSTART_MASK	GENMASK(28, 16)
+#define XSTC_GV1_BPSTART_SHIFT	16
+#define XSTC_GV1_SYNCSTART_MASK	GENMASK(12, 0)
+/* timing generator/detector vblank/vsync horizontal offset registers */
+#define XSTC_XVXHOX_HEND_MASK	GENMASK(28, 16)
+#define XSTC_XVXHOX_HEND_SHIFT	16
+#define XSTC_XVXHOX_HSTART_MASK	GENMASK(12, 0)
+
+#define XSTC_GHFRAME_HSIZE	GENMASK(12, 0)
+#define XSTC_GVFRAME_HSIZE_F1	GENMASK(12, 0)
+#define XSTC_GA_ACTSIZE_MASK	GENMASK(12, 0)
+/* reset register bit definition */
+#define XSTC_RST		BIT(31)
+/* Interlaced bit in XSTC_GENC */
+#define XSTC_GENC_INTERL	BIT(6)
+
+/**
+ * struct xlnx_stc_polarity - timing signal polarity
+ *
+ * @field_id: field ID polarity
+ * @vblank: vblank polarity
+ * @vsync: vsync polarity
+ * @hblank: hblank polarity
+ * @hsync: hsync polarity
+ */
+struct xlnx_stc_polarity {
+	u8 field_id;
+	u8 vblank;
+	u8 vsync;
+	u8 hblank;
+	u8 hsync;
+};
+
+/**
+ * struct xlnx_stc_hori_off - timing signal horizontal offset
+ *
+ * @v0blank_hori_start: vblank horizontal start (field 0)
+ * @v0blank_hori_end: vblank horizontal end (field 0)
+ * @v0sync_hori_start: vsync horizontal start (field 0)
+ * @v0sync_hori_end: vsync horizontal end (field 0)
+ * @v1blank_hori_start: vblank horizontal start (field 1)
+ * @v1blank_hori_end: vblank horizontal end (field 1)
+ * @v1sync_hori_start: vsync horizontal start (field 1)
+ * @v1sync_hori_end: vsync horizontal end (field 1)
+ */
+struct xlnx_stc_hori_off {
+	u16 v0blank_hori_start;
+	u16 v0blank_hori_end;
+	u16 v0sync_hori_start;
+	u16 v0sync_hori_end;
+	u16 v1blank_hori_start;
+	u16 v1blank_hori_end;
+	u16 v1sync_hori_start;
+	u16 v1sync_hori_end;
+};
+
+/**
+ * xlnx_stc_writel - Memory mapped SDI Tx timing controller write
+ * @base:	Pointer to SDI Tx registers base
+ * @offset:	Register offset
+ * @val:	value to be written
+ *
+ * This function writes the value to SDI TX timing controller registers
+ */
+static inline void xlnx_stc_writel(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + XSTC_OFFSET + offset);
+}
+
+/**
+ * xlnx_stc_readl - Memory mapped timing controllerregister read
+ * @base:	Pointer to SDI Tx registers base
+ * @offset:	Register offset
+ *
+ * Return: The contents of the SDI Tx timing controller register
+ *
+ * This function returns the contents of the corresponding SDI Tx register.
+ */
+static inline u32 xlnx_stc_readl(void __iomem *base, int offset)
+{
+	return readl(base + XSTC_OFFSET + offset);
+}
+
+/**
+ * xlnx_stc_enable - Enable timing controller
+ * @base:	Base address of SDI Tx subsystem
+ *
+ * This function enables the SDI Tx subsystem's timing controller
+ */
+void xlnx_stc_enable(void __iomem *base)
+{
+	u32 reg;
+
+	reg = xlnx_stc_readl(base, XSTC_CTL);
+	xlnx_stc_writel(base, XSTC_CTL, reg | XSTC_CTL_GE);
+}
+
+/**
+ * xlnx_stc_disable - Disable timing controller
+ * @base:	Base address of SDI Tx subsystem
+ *
+ * This function disables the SDI Tx subsystem's timing controller
+ */
+void xlnx_stc_disable(void __iomem *base)
+{
+	u32 reg;
+
+	reg = xlnx_stc_readl(base, XSTC_CTL);
+	xlnx_stc_writel(base, XSTC_CTL, reg & ~XSTC_CTL_GE);
+}
+
+/**
+ * xlnx_stc_reset - Reset timing controller
+ * @base:	Base address of SDI Tx subsystem
+ *
+ * This function resets the SDI Tx subsystem's timing controller
+ */
+void xlnx_stc_reset(void __iomem *base)
+{
+	u32 reg;
+
+	xlnx_stc_writel(base, XSTC_CTL, XSTC_RST);
+
+	/* enable register update */
+	reg = xlnx_stc_readl(base, XSTC_CTL);
+	xlnx_stc_writel(base, XSTC_CTL, reg | XSTC_CTL_RU);
+}
+
+/**
+ * xlnx_stc_polarity - Configure timing signal polarity
+ * @base:	Base address of SDI Tx subsystem
+ * @polarity:	timing signal polarity data
+ *
+ * This function configure timing signal polarity
+ */
+static void xlnx_stc_polarity(void __iomem *base,
+			      struct xlnx_stc_polarity *polarity)
+{
+	u32 reg = 0;
+
+	reg = XSTC_CTL_ACP;
+	reg |= XSTC_CTL_AVP;
+	if (polarity->field_id)
+		reg |= XSTC_CTL_FIP;
+	if (polarity->vblank)
+		reg |= XSTC_CTL_VBP;
+	if (polarity->vsync)
+		reg |= XSTC_CTL_VSP;
+	if (polarity->hblank)
+		reg |= XSTC_CTL_HBP;
+	if (polarity->hsync)
+		reg |= XSTC_CTL_HSP;
+
+	xlnx_stc_writel(base, XSTC_GPOL, reg);
+}
+
+/**
+ * xlnx_stc_hori_off - Configure horzontal timing offset
+ * @base:	Base address of SDI Tx subsystem
+ * @hori_off:	horizontal offset configuration data
+ * @flags:	Display flags
+ *
+ * This function configure horizontal offset
+ */
+static void xlnx_stc_hori_off(void __iomem *base,
+			      struct xlnx_stc_hori_off *hori_off,
+			      enum display_flags flags)
+{
+	u32 reg;
+
+	/* Calculate and update Generator VBlank Hori field 0 */
+	reg = hori_off->v0blank_hori_start & XSTC_XVXHOX_HSTART_MASK;
+	reg |= (hori_off->v0blank_hori_end << XSTC_XVXHOX_HEND_SHIFT) &
+		XSTC_XVXHOX_HEND_MASK;
+	xlnx_stc_writel(base, XSTC_GVBH_F0, reg);
+
+	/* Calculate and update Generator VSync Hori field 0 */
+	reg = hori_off->v0sync_hori_start & XSTC_XVXHOX_HSTART_MASK;
+	reg |= (hori_off->v0sync_hori_end << XSTC_XVXHOX_HEND_SHIFT) &
+		XSTC_XVXHOX_HEND_MASK;
+	xlnx_stc_writel(base, XSTC_GVSH_F0, reg);
+
+	/* Calculate and update Generator VBlank Hori field 1 */
+	if (flags & DISPLAY_FLAGS_INTERLACED) {
+		reg = hori_off->v1blank_hori_start & XSTC_XVXHOX_HSTART_MASK;
+		reg |= (hori_off->v1blank_hori_end << XSTC_XVXHOX_HEND_SHIFT) &
+			XSTC_XVXHOX_HEND_MASK;
+		xlnx_stc_writel(base, XSTC_GVBH_F1, reg);
+	}
+
+	/* Calculate and update Generator VBlank Hori field 1 */
+	if (flags & DISPLAY_FLAGS_INTERLACED) {
+		reg = hori_off->v1sync_hori_start & XSTC_XVXHOX_HSTART_MASK;
+		reg |= (hori_off->v1sync_hori_end << XSTC_XVXHOX_HEND_SHIFT) &
+			XSTC_XVXHOX_HEND_MASK;
+		xlnx_stc_writel(base, XSTC_GVSH_F1, reg);
+	}
+}
+
+/**
+ * xlnx_stc_src - Configure timing source
+ * @base:	Base address of SDI Tx subsystem
+ *
+ * This function configure timing source
+ */
+static void xlnx_stc_src(void __iomem *base)
+{
+	u32 reg;
+
+	reg = xlnx_stc_readl(base, XSTC_CTL);
+	reg |= XSTC_CTL_VCSS;
+	reg |= XSTC_CTL_VASS;
+	reg |= XSTC_CTL_VBSS;
+	reg |= XSTC_CTL_VSSS;
+	reg |= XSTC_CTL_VFSS;
+	reg |= XSTC_CTL_VTSS;
+	reg |= XSTC_CTL_HBSS;
+	reg |= XSTC_CTL_HSSS;
+	reg |= XSTC_CTL_HFSS;
+	reg |= XSTC_CTL_HTSS;
+	xlnx_stc_writel(base, XSTC_CTL, reg);
+}
+
+/**
+ * xlnx_stc_sig - Generates timing signal
+ * @base:	Base address of SDI Tx subsystem
+ * @vm:		video mode
+ *
+ * This function generated the timing for given vide mode
+ */
+void xlnx_stc_sig(void __iomem *base, struct videomode *vm)
+{
+	u32 reg;
+	u32 htotal, hactive, hsync_start, hbackporch_start;
+	u32 vtotal, vactive, vsync_start, vbackporch_start;
+	struct xlnx_stc_hori_off hori_off;
+	struct xlnx_stc_polarity polarity;
+
+	reg = xlnx_stc_readl(base, XSTC_CTL);
+	xlnx_stc_writel(base, XSTC_CTL, reg & ~XSTC_CTL_RU);
+
+	htotal = vm->hactive + vm->hfront_porch + vm->hsync_len +
+		 vm->hback_porch;
+	vtotal = vm->vactive + vm->vfront_porch + vm->vsync_len +
+		 vm->vback_porch;
+	hactive = vm->hactive;
+	vactive = vm->vactive;
+	hsync_start = vm->hactive + vm->hfront_porch;
+	vsync_start = vm->vactive + vm->vfront_porch;
+	hbackporch_start = hsync_start + vm->hsync_len;
+	vbackporch_start = vsync_start + vm->vsync_len;
+
+	DRM_DEBUG_DRIVER("ha: %d, va: %d\n", hactive, vactive);
+	DRM_DEBUG_DRIVER("hs: %d, hb: %d\n", hsync_start, hbackporch_start);
+	DRM_DEBUG_DRIVER("vs: %d, vb: %d\n", vsync_start, vbackporch_start);
+	DRM_DEBUG_DRIVER("ht: %d, vt: %d\n", htotal, vtotal);
+
+	reg = htotal & XSTC_GHFRAME_HSIZE;
+	xlnx_stc_writel(base, XSTC_GHSIZE, reg);
+	reg = vtotal & XSTC_GVFRAME_HSIZE_F1;
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		if (vm->pixelclock == 148500000)
+			reg |= (reg + 2) <<
+				XSTC_GV1_BPSTART_SHIFT;
+		else
+			reg |= (reg + 1) <<
+				XSTC_GV1_BPSTART_SHIFT;
+	} else {
+		reg |= reg << XSTC_GV1_BPSTART_SHIFT;
+	}
+	xlnx_stc_writel(base, XSTC_GVSIZE, reg);
+	reg = hactive & XSTC_GA_ACTSIZE_MASK;
+	reg |= (vactive & XSTC_GA_ACTSIZE_MASK) << 16;
+	xlnx_stc_writel(base, XSTC_GASIZE, reg);
+
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		if (vactive == 243)
+			reg = ((vactive + 1) & XSTC_GA_ACTSIZE_MASK) << 16;
+		else
+			reg = (vactive & XSTC_GA_ACTSIZE_MASK) << 16;
+		xlnx_stc_writel(base, XSTC_GASIZE_F1, reg);
+	}
+
+	reg = hsync_start & XSTC_GH1_SYNCSTART_MASK;
+	reg |= (hbackporch_start << XSTC_GH1_BPSTART_SHIFT) &
+	       XSTC_GH1_BPSTART_MASK;
+	xlnx_stc_writel(base, XSTC_GHSYNC, reg);
+	reg = vsync_start & XSTC_GV1_SYNCSTART_MASK;
+	reg |= (vbackporch_start << XSTC_GV1_BPSTART_SHIFT) &
+	       XSTC_GV1_BPSTART_MASK;
+
+	/*
+	 * Fix the Vsync_vstart and vsync_vend of Field 0
+	 * for all interlaced modes including 3GB.
+	 */
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED)
+		reg = ((((reg & XSTC_GV1_BPSTART_MASK) >>
+			XSTC_GV1_BPSTART_SHIFT) - 1) <<
+			XSTC_GV1_BPSTART_SHIFT) |
+			((reg & XSTC_GV1_SYNCSTART_MASK) - 1);
+
+	xlnx_stc_writel(base, XSTC_GVSYNC_F0, reg);
+
+	/*
+	 * Fix the Vsync_vstart and vsync_vend of Field 1
+	 * for interlaced and 3GB modes.
+	 */
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		if (vm->pixelclock == 148500000)
+			/* Revert and increase by 1 for 3GB mode */
+			reg = ((((reg & XSTC_GV1_BPSTART_MASK) >>
+				XSTC_GV1_BPSTART_SHIFT) + 2) <<
+				XSTC_GV1_BPSTART_SHIFT) |
+				((reg & XSTC_GV1_SYNCSTART_MASK) + 2);
+		else
+			/* Only revert the reduction */
+			reg = ((((reg & XSTC_GV1_BPSTART_MASK) >>
+				XSTC_GV1_BPSTART_SHIFT) + 1) <<
+				XSTC_GV1_BPSTART_SHIFT) |
+				((reg & XSTC_GV1_SYNCSTART_MASK) + 1);
+	}
+
+	hori_off.v0blank_hori_start = hactive;
+	hori_off.v0blank_hori_end = hactive;
+	hori_off.v0sync_hori_start = hsync_start;
+	hori_off.v0sync_hori_end = hsync_start;
+	hori_off.v1blank_hori_start = hactive;
+	hori_off.v1blank_hori_end = hactive;
+
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		hori_off.v1sync_hori_start = hsync_start - (htotal / 2);
+		hori_off.v1sync_hori_end = hsync_start - (htotal / 2);
+		xlnx_stc_writel(base, XSTC_GVSYNC_F1, reg);
+		reg = xlnx_stc_readl(base, XSTC_GENC)
+				     | XSTC_GENC_INTERL;
+		xlnx_stc_writel(base, XSTC_GENC, reg);
+	} else {
+		hori_off.v1sync_hori_start = hsync_start;
+		hori_off.v1sync_hori_end = hsync_start;
+		reg = xlnx_stc_readl(base, XSTC_GENC)
+				     & ~XSTC_GENC_INTERL;
+		xlnx_stc_writel(base, XSTC_GENC, reg);
+	}
+
+	xlnx_stc_hori_off(base, &hori_off, vm->flags);
+	/* set up polarity */
+	memset(&polarity, 0x0, sizeof(polarity));
+	polarity.hsync = !!(vm->flags & DISPLAY_FLAGS_HSYNC_LOW);
+	polarity.vsync = !!(vm->flags & DISPLAY_FLAGS_VSYNC_LOW);
+	polarity.hblank = !!(vm->flags & DISPLAY_FLAGS_HSYNC_LOW);
+	polarity.vblank = !!(vm->flags & DISPLAY_FLAGS_VSYNC_LOW);
+	polarity.field_id = !!(vm->flags & DISPLAY_FLAGS_INTERLACED);
+	xlnx_stc_polarity(base, &polarity);
+
+	xlnx_stc_src(base);
+
+	reg = xlnx_stc_readl(base, XSTC_CTL);
+	xlnx_stc_writel(base, XSTC_CTL, reg | XSTC_CTL_RU);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_sdi_timing.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_sdi_timing.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx FPGA SDI Tx timing controller driver
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Contacts: Saurabh Sengar <saurabhs@xilinx.com>
+ */
+
+#ifndef _XLNX_SDI_TIMING_H_
+#define _XLNX_SDI_TIMING_H_
+
+struct videomode;
+
+void xlnx_stc_enable(void __iomem *base);
+void xlnx_stc_disable(void __iomem *base);
+void xlnx_stc_reset(void __iomem *base);
+void xlnx_stc_sig(void __iomem *base, struct videomode *vm);
+
+#endif /* _XLNX_SDI_TIMING_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/xlnx_vtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/xlnx_vtc.c
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Video Timing Controller support for Xilinx DRM KMS
+ *
+ * Copyright (C) 2013 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyunk@xilinx.com>
+ *	   Saurabh Sengar <saurabhs@xilinx.com>
+ *	   Vishal Sagar <vishal.sagar@xilinx.com>
+ *
+ * This driver adds support to control the Xilinx Video Timing
+ * Controller connected to the CRTC.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <video/videomode.h>
+#include "xlnx_bridge.h"
+
+/* register offsets */
+#define XVTC_CTL		0x000
+#define XVTC_VER		0x010
+#define XVTC_GASIZE		0x060
+#define XVTC_GENC		0x068
+#define XVTC_GPOL		0x06c
+#define XVTC_GHSIZE		0x070
+#define XVTC_GVSIZE		0x074
+#define XVTC_GHSYNC		0x078
+#define XVTC_GVBHOFF_F0		0x07c
+#define XVTC_GVSYNC_F0		0x080
+#define XVTC_GVSHOFF_F0		0x084
+#define XVTC_GVBHOFF_F1		0x088
+#define XVTC_GVSYNC_F1		0x08C
+#define XVTC_GVSHOFF_F1		0x090
+#define XVTC_GASIZE_F1		0x094
+
+/* vtc control register bits */
+#define XVTC_CTL_SWRESET	BIT(31)
+#define XVTC_CTL_FIPSS		BIT(26)
+#define XVTC_CTL_ACPSS		BIT(25)
+#define XVTC_CTL_AVPSS		BIT(24)
+#define XVTC_CTL_HSPSS		BIT(23)
+#define XVTC_CTL_VSPSS		BIT(22)
+#define XVTC_CTL_HBPSS		BIT(21)
+#define XVTC_CTL_VBPSS		BIT(20)
+#define XVTC_CTL_VCSS		BIT(18)
+#define XVTC_CTL_VASS		BIT(17)
+#define XVTC_CTL_VBSS		BIT(16)
+#define XVTC_CTL_VSSS		BIT(15)
+#define XVTC_CTL_VFSS		BIT(14)
+#define XVTC_CTL_VTSS		BIT(13)
+#define XVTC_CTL_HBSS		BIT(11)
+#define XVTC_CTL_HSSS		BIT(10)
+#define XVTC_CTL_HFSS		BIT(9)
+#define XVTC_CTL_HTSS		BIT(8)
+#define XVTC_CTL_GE		BIT(2)
+#define XVTC_CTL_RU		BIT(1)
+
+/* vtc generator polarity register bits */
+#define XVTC_GPOL_FIP		BIT(6)
+#define XVTC_GPOL_ACP		BIT(5)
+#define XVTC_GPOL_AVP		BIT(4)
+#define XVTC_GPOL_HSP		BIT(3)
+#define XVTC_GPOL_VSP		BIT(2)
+#define XVTC_GPOL_HBP		BIT(1)
+#define XVTC_GPOL_VBP		BIT(0)
+
+/* vtc generator horizontal 1 */
+#define XVTC_GH1_BPSTART_MASK	GENMASK(28, 16)
+#define XVTC_GH1_BPSTART_SHIFT	16
+#define XVTC_GH1_SYNCSTART_MASK GENMASK(12, 0)
+/* vtc generator vertical 1 (field 0) */
+#define XVTC_GV1_BPSTART_MASK	GENMASK(28, 16)
+#define XVTC_GV1_BPSTART_SHIFT	16
+#define XVTC_GV1_SYNCSTART_MASK	GENMASK(12, 0)
+/* vtc generator/detector vblank/vsync horizontal offset registers */
+#define XVTC_XVXHOX_HEND_MASK	GENMASK(28, 16)
+#define XVTC_XVXHOX_HEND_SHIFT	16
+#define XVTC_XVXHOX_HSTART_MASK	GENMASK(12, 0)
+
+#define XVTC_GHFRAME_HSIZE	GENMASK(12, 0)
+#define XVTC_GVFRAME_HSIZE_F1	GENMASK(12, 0)
+#define XVTC_GA_ACTSIZE_MASK	GENMASK(12, 0)
+
+/* vtc generator encoding register bits */
+#define XVTC_GENC_INTERL	BIT(6)
+
+/**
+ * struct xlnx_vtc - Xilinx VTC object
+ *
+ * @bridge: xilinx bridge structure
+ * @dev: device structure
+ * @base: base addr
+ * @ppc: pixels per clock
+ * @axi_clk: AXI Lite clock
+ * @vid_clk: Video clock
+ */
+struct xlnx_vtc {
+	struct xlnx_bridge bridge;
+	struct device *dev;
+	void __iomem *base;
+	u32 ppc;
+	struct clk *axi_clk;
+	struct clk *vid_clk;
+};
+
+static inline void xlnx_vtc_writel(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + offset);
+}
+
+static inline u32 xlnx_vtc_readl(void __iomem *base, int offset)
+{
+	return readl(base + offset);
+}
+
+static inline struct xlnx_vtc *bridge_to_vtc(struct xlnx_bridge *bridge)
+{
+	return container_of(bridge, struct xlnx_vtc, bridge);
+}
+
+static void xlnx_vtc_reset(struct xlnx_vtc *vtc)
+{
+	u32 reg;
+
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, XVTC_CTL_SWRESET);
+
+	/* enable register update */
+	reg = xlnx_vtc_readl(vtc->base, XVTC_CTL);
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, reg | XVTC_CTL_RU);
+}
+
+/**
+ * xlnx_vtc_enable - Enable the VTC
+ * @bridge: xilinx bridge structure pointer
+ *
+ * Return:
+ * Zero on success.
+ *
+ * This function enables the VTC
+ */
+static int xlnx_vtc_enable(struct xlnx_bridge *bridge)
+{
+	u32 reg;
+	struct xlnx_vtc *vtc = bridge_to_vtc(bridge);
+
+	/* enable generator */
+	reg = xlnx_vtc_readl(vtc->base, XVTC_CTL);
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, reg | XVTC_CTL_GE);
+	dev_dbg(vtc->dev, "enabled\n");
+	return 0;
+}
+
+/**
+ * xlnx_vtc_disable - Disable the VTC
+ * @bridge: xilinx bridge structure pointer
+ *
+ * This function disables and resets the VTC.
+ */
+static void xlnx_vtc_disable(struct xlnx_bridge *bridge)
+{
+	u32 reg;
+	struct xlnx_vtc *vtc = bridge_to_vtc(bridge);
+
+	/* disable generator and reset */
+	reg = xlnx_vtc_readl(vtc->base, XVTC_CTL);
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, reg & ~XVTC_CTL_GE);
+	xlnx_vtc_reset(vtc);
+	dev_dbg(vtc->dev, "disabled\n");
+}
+
+/**
+ * xlnx_vtc_set_timing - Configures the VTC
+ * @bridge: xilinx bridge structure pointer
+ * @vm: video mode requested
+ *
+ * Return:
+ * Zero on success.
+ *
+ * This function calculates the timing values from the video mode
+ * structure passed from the CRTC and configures the VTC.
+ */
+static int xlnx_vtc_set_timing(struct xlnx_bridge *bridge,
+			       struct videomode *vm)
+{
+	u32 reg;
+	u32 htotal, hactive, hsync_start, hbackporch_start;
+	u32 vtotal, vactive, vsync_start, vbackporch_start;
+	struct xlnx_vtc *vtc = bridge_to_vtc(bridge);
+
+	reg = xlnx_vtc_readl(vtc->base, XVTC_CTL);
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, reg & ~XVTC_CTL_RU);
+
+	vm->hactive /= vtc->ppc;
+	vm->hfront_porch /= vtc->ppc;
+	vm->hback_porch /= vtc->ppc;
+	vm->hsync_len /= vtc->ppc;
+
+	htotal = vm->hactive + vm->hfront_porch + vm->hsync_len +
+		 vm->hback_porch;
+	vtotal = vm->vactive + vm->vfront_porch + vm->vsync_len +
+		 vm->vback_porch;
+
+	hactive = vm->hactive;
+	vactive = vm->vactive;
+
+	hsync_start = vm->hactive + vm->hfront_porch;
+	vsync_start = vm->vactive + vm->vfront_porch;
+
+	hbackporch_start = hsync_start + vm->hsync_len;
+	vbackporch_start = vsync_start + vm->vsync_len;
+
+	dev_dbg(vtc->dev, "ha: %d, va: %d\n", hactive, vactive);
+	dev_dbg(vtc->dev, "ht: %d, vt: %d\n", htotal, vtotal);
+	dev_dbg(vtc->dev, "hs: %d, hb: %d\n", hsync_start, hbackporch_start);
+	dev_dbg(vtc->dev, "vs: %d, vb: %d\n", vsync_start, vbackporch_start);
+
+	reg = htotal & XVTC_GHFRAME_HSIZE;
+	xlnx_vtc_writel(vtc->base, XVTC_GHSIZE, reg);
+
+	reg = vtotal & XVTC_GVFRAME_HSIZE_F1;
+	reg |= reg << XVTC_GV1_BPSTART_SHIFT;
+	xlnx_vtc_writel(vtc->base, XVTC_GVSIZE, reg);
+
+	reg = hactive & XVTC_GA_ACTSIZE_MASK;
+	reg |= (vactive & XVTC_GA_ACTSIZE_MASK) << 16;
+	xlnx_vtc_writel(vtc->base, XVTC_GASIZE, reg);
+
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED)
+		xlnx_vtc_writel(vtc->base, XVTC_GASIZE_F1, reg);
+
+	reg = hsync_start & XVTC_GH1_SYNCSTART_MASK;
+	reg |= (hbackporch_start << XVTC_GH1_BPSTART_SHIFT) &
+	       XVTC_GH1_BPSTART_MASK;
+	xlnx_vtc_writel(vtc->base, XVTC_GHSYNC, reg);
+
+	reg = vsync_start & XVTC_GV1_SYNCSTART_MASK;
+	reg |= (vbackporch_start << XVTC_GV1_BPSTART_SHIFT) &
+	       XVTC_GV1_BPSTART_MASK;
+	xlnx_vtc_writel(vtc->base, XVTC_GVSYNC_F0, reg);
+
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		xlnx_vtc_writel(vtc->base, XVTC_GVSYNC_F1, reg);
+		reg = xlnx_vtc_readl(vtc->base, XVTC_GENC) | XVTC_GENC_INTERL;
+		xlnx_vtc_writel(vtc->base, XVTC_GENC, reg);
+	} else {
+		reg = xlnx_vtc_readl(vtc->base, XVTC_GENC) & ~XVTC_GENC_INTERL;
+		xlnx_vtc_writel(vtc->base, XVTC_GENC, reg);
+	}
+
+	/* configure horizontal offset */
+	/* Calculate and update Generator VBlank Hori field 0 */
+	reg = hactive & XVTC_XVXHOX_HSTART_MASK;
+	reg |= (hactive << XVTC_XVXHOX_HEND_SHIFT) &
+		XVTC_XVXHOX_HEND_MASK;
+	xlnx_vtc_writel(vtc->base, XVTC_GVBHOFF_F0, reg);
+
+	/* Calculate and update Generator VSync Hori field 0 */
+	reg = hsync_start & XVTC_XVXHOX_HSTART_MASK;
+	reg |= (hsync_start << XVTC_XVXHOX_HEND_SHIFT) &
+		XVTC_XVXHOX_HEND_MASK;
+	xlnx_vtc_writel(vtc->base, XVTC_GVSHOFF_F0, reg);
+
+	/* Calculate and update Generator VBlank Hori field 1 */
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		reg = hactive & XVTC_XVXHOX_HSTART_MASK;
+		reg |= (hactive << XVTC_XVXHOX_HEND_SHIFT) &
+			XVTC_XVXHOX_HEND_MASK;
+		xlnx_vtc_writel(vtc->base, XVTC_GVBHOFF_F1, reg);
+	}
+
+	/* Calculate and update Generator VBlank Hori field 1 */
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED) {
+		reg =  (hsync_start - (htotal / 2)) & XVTC_XVXHOX_HSTART_MASK;
+		reg |= ((hsync_start - (htotal / 2)) <<
+			XVTC_XVXHOX_HEND_SHIFT) & XVTC_XVXHOX_HEND_MASK;
+	} else {
+		reg =  hsync_start & XVTC_XVXHOX_HSTART_MASK;
+		reg |= (hsync_start << XVTC_XVXHOX_HEND_SHIFT) &
+			XVTC_XVXHOX_HEND_MASK;
+	}
+
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED)
+		xlnx_vtc_writel(vtc->base, XVTC_GVSHOFF_F1, reg);
+
+	/* configure polarity of signals */
+	reg = 0;
+	reg |= XVTC_GPOL_ACP;
+	reg |= XVTC_GPOL_AVP;
+	if (vm->flags & DISPLAY_FLAGS_INTERLACED)
+		reg |= XVTC_GPOL_FIP;
+	if (vm->flags & DISPLAY_FLAGS_VSYNC_HIGH) {
+		reg |= XVTC_GPOL_VBP;
+		reg |= XVTC_GPOL_VSP;
+	}
+	if (vm->flags & DISPLAY_FLAGS_HSYNC_HIGH) {
+		reg |= XVTC_GPOL_HBP;
+		reg |= XVTC_GPOL_HSP;
+	}
+	xlnx_vtc_writel(vtc->base, XVTC_GPOL, reg);
+
+	/* configure timing source */
+	reg = xlnx_vtc_readl(vtc->base, XVTC_CTL);
+	reg |= XVTC_CTL_VCSS;
+	reg |= XVTC_CTL_VASS;
+	reg |= XVTC_CTL_VBSS;
+	reg |= XVTC_CTL_VSSS;
+	reg |= XVTC_CTL_VFSS;
+	reg |= XVTC_CTL_VTSS;
+	reg |= XVTC_CTL_HBSS;
+	reg |= XVTC_CTL_HSSS;
+	reg |= XVTC_CTL_HFSS;
+	reg |= XVTC_CTL_HTSS;
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, reg);
+
+	reg = xlnx_vtc_readl(vtc->base, XVTC_CTL);
+	xlnx_vtc_writel(vtc->base, XVTC_CTL, reg | XVTC_CTL_RU);
+	dev_dbg(vtc->dev, "set timing done\n");
+
+	return 0;
+}
+
+static int xlnx_vtc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct xlnx_vtc *vtc;
+	struct resource *res;
+	int ret;
+
+	vtc = devm_kzalloc(dev, sizeof(*vtc), GFP_KERNEL);
+	if (!vtc)
+		return -ENOMEM;
+
+	vtc->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "failed to get resource for device\n");
+		return -EFAULT;
+	}
+
+	vtc->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(vtc->base)) {
+		dev_err(dev, "failed to remap io region\n");
+		return PTR_ERR(vtc->base);
+	}
+
+	platform_set_drvdata(pdev, vtc);
+
+	ret = of_property_read_u32(dev->of_node, "xlnx,pixels-per-clock",
+				   &vtc->ppc);
+	if (ret || (vtc->ppc != 1 && vtc->ppc != 2 && vtc->ppc != 4)) {
+		dev_err(dev, "failed to get ppc\n");
+		return ret;
+	}
+	dev_info(dev, "vtc ppc = %d\n", vtc->ppc);
+
+	vtc->axi_clk = devm_clk_get(vtc->dev, "s_axi_aclk");
+	if (IS_ERR(vtc->axi_clk)) {
+		ret = PTR_ERR(vtc->axi_clk);
+		dev_err(dev, "failed to get axi lite clk %d\n", ret);
+		return ret;
+	}
+
+	vtc->vid_clk = devm_clk_get(vtc->dev, "clk");
+	if (IS_ERR(vtc->vid_clk)) {
+		ret = PTR_ERR(vtc->vid_clk);
+		dev_err(dev, "failed to get video clk %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(vtc->axi_clk);
+	if (ret) {
+		dev_err(vtc->dev, "unable to enable axilite clk %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(vtc->vid_clk);
+	if (ret) {
+		dev_err(vtc->dev, "unable to enable video clk %d\n", ret);
+		goto err_axi_clk;
+	}
+
+	xlnx_vtc_reset(vtc);
+
+	vtc->bridge.enable = &xlnx_vtc_enable;
+	vtc->bridge.disable = &xlnx_vtc_disable;
+	vtc->bridge.set_timing = &xlnx_vtc_set_timing;
+	vtc->bridge.of_node = dev->of_node;
+	ret = xlnx_bridge_register(&vtc->bridge);
+	if (ret) {
+		dev_err(dev, "Bridge registration failed\n");
+		goto err_vid_clk;
+	}
+
+	dev_info(dev, "Xilinx VTC IP version : 0x%08x\n",
+		 xlnx_vtc_readl(vtc->base, XVTC_VER));
+	dev_info(dev, "Xilinx VTC DRM Bridge driver probed\n");
+	return 0;
+
+err_vid_clk:
+	clk_disable_unprepare(vtc->vid_clk);
+err_axi_clk:
+	clk_disable_unprepare(vtc->axi_clk);
+	return ret;
+}
+
+static int xlnx_vtc_remove(struct platform_device *pdev)
+{
+	struct xlnx_vtc *vtc = platform_get_drvdata(pdev);
+
+	xlnx_bridge_unregister(&vtc->bridge);
+	clk_disable_unprepare(vtc->vid_clk);
+	clk_disable_unprepare(vtc->axi_clk);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_vtc_of_match[] = {
+	{ .compatible = "xlnx,bridge-v-tc-6.1" },
+	{ /* end of table */ },
+};
+
+MODULE_DEVICE_TABLE(of, xlnx_vtc_of_match);
+
+static struct platform_driver xlnx_vtc_bridge_driver = {
+	.probe = xlnx_vtc_probe,
+	.remove = xlnx_vtc_remove,
+	.driver = {
+		.name = "xlnx,bridge-vtc",
+		.of_match_table = xlnx_vtc_of_match,
+	},
+};
+
+module_platform_driver(xlnx_vtc_bridge_driver);
+
+MODULE_AUTHOR("Vishal Sagar");
+MODULE_DESCRIPTION("Xilinx VTC Bridge Driver");
+MODULE_LICENSE("GPL v2");
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_disp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_disp.c
@@ -13,25 +13,35 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_atomic_uapi.h>
 #include <drm/drm_crtc.h>
-#include <drm/drm_device.h>
+#include <drm/drm_crtc_helper.h>
 #include <drm/drm_fb_cma_helper.h>
 #include <drm/drm_fourcc.h>
-#include <drm/drm_framebuffer.h>
-#include <drm/drm_managed.h>
-#include <drm/drm_plane.h>
 #include <drm/drm_plane_helper.h>
 #include <drm/drm_vblank.h>
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/device.h>
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/irqreturn.h>
+#include <linux/list.h>
 #include <linux/module.h>
+#include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/of_dma.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/spinlock.h>
-
+#include <linux/uaccess.h>
+#include <video/videomode.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+#include "xlnx_bridge.h"
+#include "xlnx_crtc.h"
+#include "xlnx_fb.h"
 #include "zynqmp_disp.h"
 #include "zynqmp_disp_regs.h"
 #include "zynqmp_dp.h"
@@ -41,61 +51,70 @@
  * Overview
  * --------
  *
- * The display controller part of ZynqMP DP subsystem, made of the Audio/Video
- * Buffer Manager, the Video Rendering Pipeline (blender) and the Audio Mixer.
- *
- *              +------------------------------------------------------------+
- * +--------+   | +----------------+     +-----------+                       |
- * | DPDMA  | --->|                | --> |   Video   | Video +-------------+ |
- * | 4x vid |   | |                |     | Rendering | -+--> |             | |   +------+
- * | 2x aud |   | |  Audio/Video   | --> | Pipeline  |  |    | DisplayPort |---> | PHY0 |
- * +--------+   | | Buffer Manager |     +-----------+  |    |   Source    | |   +------+
- *              | |    and STC     |     +-----------+  |    | Controller  | |   +------+
- * Live Video --->|                | --> |   Audio   | Audio |             |---> | PHY1 |
- *              | |                |     |   Mixer   | --+-> |             | |   +------+
- * Live Audio --->|                | --> |           |  ||   +-------------+ |
- *              | +----------------+     +-----------+  ||                   |
- *              +---------------------------------------||-------------------+
- *                                                      vv
- *                                                Blended Video and
- *                                                Mixed Audio to PL
- *
- * Only non-live input from the DPDMA and output to the DisplayPort Source
- * Controller are currently supported. Interface with the programmable logic
- * for live streams is not implemented.
- *
- * The display controller code creates planes for the DPDMA video and graphics
- * layers, and a CRTC for the Video Rendering Pipeline.
- */
+ * The display part of ZynqMP DP subsystem. Internally, the device
+ * is partitioned into 3 blocks: AV buffer manager, Blender, Audio.
+ * The driver creates the DRM crtc and plane objectes and maps the DRM
+ * interface into those 3 blocks. In high level, the driver is layered
+ * in the following way:
+ *
+ * zynqmp_disp_crtc & zynqmp_disp_plane
+ * |->zynqmp_disp
+ *	|->zynqmp_disp_aud
+ *	|->zynqmp_disp_blend
+ *	|->zynqmp_disp_av_buf
+ *
+ * The driver APIs are used externally by
+ * - zynqmp_dpsub: Top level ZynqMP DP subsystem driver
+ * - zynqmp_dp: ZynqMP DP driver
+ * - xlnx_crtc: Xilinx DRM specific crtc functions
+ */
+
+/* The default value is ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB565 */
+static uint zynqmp_disp_gfx_init_fmt;
+module_param_named(gfx_init_fmt, zynqmp_disp_gfx_init_fmt, uint, 0444);
+MODULE_PARM_DESC(gfx_init_fmt, "The initial format of the graphics layer\n"
+			       "\t\t0 = rgb565 (default)\n"
+			       "\t\t1 = rgb888\n"
+			       "\t\t2 = argb8888\n");
+/* These value should be mapped to index of av_buf_gfx_fmts[] */
+#define ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB565		10
+#define ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB888		5
+#define ZYNQMP_DISP_AV_BUF_GFX_FMT_ARGB8888		1
+static const u32 zynqmp_disp_gfx_init_fmts[] = {
+	ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB565,
+	ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB888,
+	ZYNQMP_DISP_AV_BUF_GFX_FMT_ARGB8888,
+};
 
 #define ZYNQMP_DISP_AV_BUF_NUM_VID_GFX_BUFFERS		4
 #define ZYNQMP_DISP_AV_BUF_NUM_BUFFERS			6
 
 #define ZYNQMP_DISP_NUM_LAYERS				2
 #define ZYNQMP_DISP_MAX_NUM_SUB_PLANES			3
-
-/**
- * struct zynqmp_disp_format - Display subsystem format information
- * @drm_fmt: DRM format (4CC)
- * @buf_fmt: AV buffer format
- * @bus_fmt: Media bus formats (live formats)
- * @swap: Flag to swap R & B for RGB formats, and U & V for YUV formats
- * @sf: Scaling factors for color components
+/*
+ * 3840x2160 is advertised max resolution, but almost any resolutions under
+ * 300Mhz pixel rate would work. Thus put 4096 as maximum width and height.
  */
-struct zynqmp_disp_format {
-	u32 drm_fmt;
-	u32 buf_fmt;
-	u32 bus_fmt;
-	bool swap;
-	const u32 *sf;
+#define ZYNQMP_DISP_MAX_WIDTH				4096
+#define ZYNQMP_DISP_MAX_HEIGHT				4096
+/* 44 bit addressing. This is actually DPDMA limitation */
+#define ZYNQMP_DISP_MAX_DMA_BIT				44
+
+static struct regmap_config dpaud_regmap_config = {
+	.name = "regmap",
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0xfff,
+	.cache_type = REGCACHE_NONE,
 };
 
 /**
- * enum zynqmp_disp_layer_id - Layer identifier
+ * enum zynqmp_disp_layer_type - Layer type (can be used for hw ID)
  * @ZYNQMP_DISP_LAYER_VID: Video layer
  * @ZYNQMP_DISP_LAYER_GFX: Graphics layer
  */
-enum zynqmp_disp_layer_id {
+enum zynqmp_disp_layer_type {
 	ZYNQMP_DISP_LAYER_VID,
 	ZYNQMP_DISP_LAYER_GFX
 };
@@ -111,1334 +130,2466 @@
 };
 
 /**
- * struct zynqmp_disp_layer_dma - DMA channel for one data plane of a layer
+ * struct zynqmp_disp_layer_dma - struct for DMA engine
  * @chan: DMA channel
- * @xt: Interleaved DMA descriptor template
+ * @is_active: flag if the DMA is active
+ * @xt: Interleaved desc config container
  * @sgl: Data chunk for dma_interleaved_template
  */
 struct zynqmp_disp_layer_dma {
 	struct dma_chan *chan;
+	bool is_active;
 	struct dma_interleaved_template xt;
-	struct data_chunk sgl;
-};
-
-/**
- * struct zynqmp_disp_layer_info - Static layer information
- * @formats: Array of supported formats
- * @num_formats: Number of formats in @formats array
- * @num_channels: Number of DMA channels
- */
-struct zynqmp_disp_layer_info {
-	const struct zynqmp_disp_format *formats;
-	unsigned int num_formats;
-	unsigned int num_channels;
+	struct data_chunk sgl[1];
 };
 
 /**
- * struct zynqmp_disp_layer - Display layer (DRM plane)
+ * struct zynqmp_disp_layer - Display subsystem layer
  * @plane: DRM plane
+ * @bridge: Xlnx bridge
+ * @dma: struct for DMA engine
+ * @num_chan: Number of DMA channel
  * @id: Layer ID
- * @disp: Back pointer to struct zynqmp_disp
- * @info: Static layer information
- * @dmas: DMA channels
- * @disp_fmt: Current format information
- * @drm_fmt: Current DRM format information
- * @mode: Current operation mode
+ * @offset: Layer offset in the register space
+ * @enabled: flag if enabled
+ * @fmt: Current format descriptor
+ * @drm_fmts: Array of supported DRM formats
+ * @num_fmts: Number of supported DRM formats
+ * @bus_fmts: Array of supported bus formats
+ * @num_bus_fmts: Number of supported bus formats
+ * @w: Width
+ * @h: Height
+ * @mode: the operation mode
+ * @other: other layer
+ * @disp: back pointer to struct zynqmp_disp
  */
 struct zynqmp_disp_layer {
 	struct drm_plane plane;
-	enum zynqmp_disp_layer_id id;
+	struct xlnx_bridge bridge;
+	struct zynqmp_disp_layer_dma dma[ZYNQMP_DISP_MAX_NUM_SUB_PLANES];
+	unsigned int num_chan;
+	enum zynqmp_disp_layer_type id;
+	u32 offset;
+	u8 enabled;
+	const struct zynqmp_disp_fmt *fmt;
+	u32 *drm_fmts;
+	unsigned int num_fmts;
+	u32 *bus_fmts;
+	unsigned int num_bus_fmts;
+	u32 w;
+	u32 h;
+	enum zynqmp_disp_layer_mode mode;
+	struct zynqmp_disp_layer *other;
 	struct zynqmp_disp *disp;
-	const struct zynqmp_disp_layer_info *info;
+};
 
-	struct zynqmp_disp_layer_dma dmas[ZYNQMP_DISP_MAX_NUM_SUB_PLANES];
+/**
+ * struct zynqmp_disp_blend - Blender
+ * @base: Base address offset
+ */
+struct zynqmp_disp_blend {
+	void __iomem *base;
+};
 
-	const struct zynqmp_disp_format *disp_fmt;
-	const struct drm_format_info *drm_fmt;
-	enum zynqmp_disp_layer_mode mode;
+/**
+ * struct zynqmp_disp_av_buf - AV buffer manager
+ * @base: Base address offset
+ */
+struct zynqmp_disp_av_buf {
+	void __iomem *base;
 };
 
 /**
- * struct zynqmp_disp - Display controller
- * @dev: Device structure
- * @drm: DRM core
+ * struct zynqmp_disp_aud - Audio
+ * @base: Base address offset
+ */
+struct zynqmp_disp_aud {
+	struct regmap *base;
+};
+
+/**
+ * struct zynqmp_disp - Display subsystem
+ * @xlnx_crtc: Xilinx DRM crtc
+ * @dev: device structure
  * @dpsub: Display subsystem
- * @crtc: DRM CRTC
- * @blend.base: Register I/O base address for the blender
- * @avbuf.base: Register I/O base address for the audio/video buffer manager
- * @audio.base: Registers I/O base address for the audio mixer
- * @audio.clk: Audio clock
- * @audio.clk_from_ps: True of the audio clock comes from PS, false from PL
- * @layers: Layers (planes)
- * @event: Pending vblank event request
+ * @drm: DRM core
+ * @enabled: flag if enabled
+ * @blend: Blender block
+ * @av_buf: AV buffer manager block
+ * @aud:Audio block
+ * @layers: layers
+ * @g_alpha_prop: global alpha property
+ * @alpha: current global alpha value
+ * @g_alpha_en_prop: the global alpha enable property
+ * @alpha_en: flag if the global alpha is enabled
+ * @color_prop: output color format property
+ * @color: current output color value
+ * @bg_c0_prop: 1st component of background color property
+ * @bg_c0: current value of 1st background color component
+ * @bg_c1_prop: 2nd component of background color property
+ * @bg_c1: current value of 2nd background color component
+ * @bg_c2_prop: 3rd component of background color property
+ * @bg_c2: current value of 3rd background color component
+ * @tpg_prop: Test Pattern Generation mode property
+ * @tpg_on: current TPG mode state
+ * @event: pending vblank event request
+ * @_ps_pclk: Pixel clock from PS
+ * @_pl_pclk: Pixel clock from PL
  * @pclk: Pixel clock
- * @pclk_from_ps: True of the video clock comes from PS, false from PL
+ * @pclk_en: Flag if the pixel clock is enabled
+ * @_ps_audclk: Audio clock from PS
+ * @_pl_audclk: Audio clock from PL
+ * @audclk: Audio clock
+ * @audclk_en: Flag if the audio clock is enabled
+ * @aclk: APB clock
+ * @aclk_en: Flag if the APB clock is enabled
+ * @vtc_bridge: vtc_bridge structure
  */
 struct zynqmp_disp {
+	struct xlnx_crtc xlnx_crtc;
 	struct device *dev;
-	struct drm_device *drm;
 	struct zynqmp_dpsub *dpsub;
+	struct drm_device *drm;
+	bool enabled;
+	struct zynqmp_disp_blend blend;
+	struct zynqmp_disp_av_buf av_buf;
+	struct zynqmp_disp_aud aud;
+	struct zynqmp_disp_layer layers[ZYNQMP_DISP_NUM_LAYERS];
+	struct drm_property *g_alpha_prop;
+	u32 alpha;
+	struct drm_property *g_alpha_en_prop;
+	bool alpha_en;
+	struct drm_property *color_prop;
+	unsigned int color;
+	struct drm_property *bg_c0_prop;
+	u32 bg_c0;
+	struct drm_property *bg_c1_prop;
+	u32 bg_c1;
+	struct drm_property *bg_c2_prop;
+	u32 bg_c2;
+	struct drm_property *tpg_prop;
+	bool tpg_on;
+	struct drm_pending_vblank_event *event;
+	/* Don't operate directly on _ps_ */
+	struct clk *_ps_pclk;
+	struct clk *_pl_pclk;
+	struct clk *pclk;
+	bool pclk_en;
+	struct clk *_ps_audclk;
+	struct clk *_pl_audclk;
+	struct clk *audclk;
+	bool audclk_en;
+	struct clk *aclk;
+	bool aclk_en;
+	struct xlnx_bridge *vtc_bridge;
+};
 
-	struct drm_crtc crtc;
+/**
+ * struct zynqmp_disp_fmt - Display subsystem format mapping
+ * @drm_fmt: drm format
+ * @disp_fmt: Display subsystem format
+ * @bus_fmt: Bus formats (live formats)
+ * @rgb: flag for RGB formats
+ * @swap: flag to swap r & b for rgb formats, and u & v for yuv formats
+ * @chroma_sub: flag for chroma subsampled formats
+ * @sf: scaling factors for up to 3 color components
+ */
+struct zynqmp_disp_fmt {
+	u32 drm_fmt;
+	u32 disp_fmt;
+	u32 bus_fmt;
+	bool rgb;
+	bool swap;
+	bool chroma_sub;
+	u32 sf[3];
+};
 
-	struct {
-		void __iomem *base;
-	} blend;
-	struct {
-		void __iomem *base;
-	} avbuf;
-	struct {
-		void __iomem *base;
-		struct clk *clk;
-		bool clk_from_ps;
-	} audio;
+static void zynqmp_disp_write(void __iomem *base, int offset, u32 val)
+{
+	writel(val, base + offset);
+}
 
-	struct zynqmp_disp_layer layers[ZYNQMP_DISP_NUM_LAYERS];
+static u32 zynqmp_disp_read(void __iomem *base, int offset)
+{
+	return readl(base + offset);
+}
 
-	struct drm_pending_vblank_event *event;
+static void zynqmp_disp_clr(void __iomem *base, int offset, u32 clr)
+{
+	zynqmp_disp_write(base, offset, zynqmp_disp_read(base, offset) & ~clr);
+}
 
-	struct clk *pclk;
-	bool pclk_from_ps;
-};
+static void zynqmp_disp_set(void __iomem *base, int offset, u32 set)
+{
+	zynqmp_disp_write(base, offset, zynqmp_disp_read(base, offset) | set);
+}
 
-/* -----------------------------------------------------------------------------
- * Audio/Video Buffer Manager
+/*
+ * Clock functions
  */
 
-static const u32 scaling_factors_444[] = {
-	ZYNQMP_DISP_AV_BUF_4BIT_SF,
-	ZYNQMP_DISP_AV_BUF_4BIT_SF,
-	ZYNQMP_DISP_AV_BUF_4BIT_SF,
-};
+/**
+ * zynqmp_disp_clk_enable - Enable the clock if needed
+ * @clk: clk device
+ * @flag: flag if the clock is enabled
+ *
+ * Enable the clock only if it's not enabled @flag.
+ *
+ * Return: value from clk_prepare_enable().
+ */
+static int zynqmp_disp_clk_enable(struct clk *clk, bool *flag)
+{
+	int ret = 0;
 
-static const u32 scaling_factors_555[] = {
-	ZYNQMP_DISP_AV_BUF_5BIT_SF,
-	ZYNQMP_DISP_AV_BUF_5BIT_SF,
-	ZYNQMP_DISP_AV_BUF_5BIT_SF,
-};
+	if (!*flag) {
+		ret = clk_prepare_enable(clk);
+		if (!ret)
+			*flag = true;
+	}
 
-static const u32 scaling_factors_565[] = {
-	ZYNQMP_DISP_AV_BUF_5BIT_SF,
-	ZYNQMP_DISP_AV_BUF_6BIT_SF,
-	ZYNQMP_DISP_AV_BUF_5BIT_SF,
-};
+	return ret;
+}
 
-static const u32 scaling_factors_888[] = {
-	ZYNQMP_DISP_AV_BUF_8BIT_SF,
-	ZYNQMP_DISP_AV_BUF_8BIT_SF,
-	ZYNQMP_DISP_AV_BUF_8BIT_SF,
-};
+/**
+ * zynqmp_disp_clk_disable - Disable the clock if needed
+ * @clk: clk device
+ * @flag: flag if the clock is enabled
+ *
+ * Disable the clock only if it's enabled @flag.
+ */
+static void zynqmp_disp_clk_disable(struct clk *clk, bool *flag)
+{
+	if (*flag) {
+		clk_disable_unprepare(clk);
+		*flag = false;
+	}
+}
+
+/**
+ * zynqmp_disp_clk_enable_disable - Enable and disable the clock
+ * @clk: clk device
+ * @flag: flag if the clock is enabled
+ *
+ * This is to ensure the clock is disabled. The initial hardware state is
+ * unknown, and this makes sure that the clock is disabled.
+ *
+ * Return: value from clk_prepare_enable().
+ */
+static int zynqmp_disp_clk_enable_disable(struct clk *clk, bool *flag)
+{
+	int ret = 0;
+
+	if (!*flag) {
+		ret = clk_prepare_enable(clk);
+		clk_disable_unprepare(clk);
+	}
+
+	return ret;
+}
+
+/*
+ * Blender functions
+ */
+
+/**
+ * zynqmp_disp_blend_set_output_fmt - Set the output format of the blend
+ * @blend: blend object
+ * @fmt: output format
+ *
+ * Set the output format to @fmt.
+ */
+static void
+zynqmp_disp_blend_set_output_fmt(struct zynqmp_disp_blend *blend, u32 fmt)
+{
+	u16 reset_coeffs[] = { 0x1000, 0x0, 0x0,
+			       0x0, 0x1000, 0x0,
+			       0x0, 0x0, 0x1000 };
+	u32 reset_offsets[] = { 0x0, 0x0, 0x0 };
+	u16 sdtv_coeffs[] = { 0x4c9, 0x864, 0x1d3,
+			      0x7d4d, 0x7ab3, 0x800,
+			      0x800, 0x794d, 0x7eb3 };
+	u32 full_range_offsets[] = { 0x0, 0x8000000, 0x8000000 };
+	u16 *coeffs;
+	u32 *offsets;
+	u32 offset, i;
+
+	zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT, fmt);
+	if (fmt == ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB) {
+		coeffs = reset_coeffs;
+		offsets = reset_offsets;
+	} else {
+		/* Hardcode Full-range SDTV values. Can be runtime config */
+		coeffs = sdtv_coeffs;
+		offsets = full_range_offsets;
+	}
+
+	offset = ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF0;
+	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i++)
+		zynqmp_disp_write(blend->base, offset + i * 4, coeffs[i]);
 
-static const u32 scaling_factors_101010[] = {
-	ZYNQMP_DISP_AV_BUF_10BIT_SF,
-	ZYNQMP_DISP_AV_BUF_10BIT_SF,
-	ZYNQMP_DISP_AV_BUF_10BIT_SF,
+	offset = ZYNQMP_DISP_V_BLEND_LUMA_OUTCSC_OFFSET;
+	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
+		zynqmp_disp_write(blend->base, offset + i * 4, offsets[i]);
+}
+
+/**
+ * zynqmp_disp_blend_layer_coeff - Set the coefficients for @layer
+ * @blend: blend object
+ * @layer: layer to set the coefficients for
+ * @on: if layer is on / off
+ *
+ * Depending on the format (rgb / yuv and swap), and the status (on / off),
+ * this function sets the coefficients for the given layer @layer accordingly.
+ */
+static void zynqmp_disp_blend_layer_coeff(struct zynqmp_disp_blend *blend,
+					  struct zynqmp_disp_layer *layer,
+					  bool on)
+{
+	u32 offset, i, s0, s1;
+	u16 sdtv_coeffs[] = { 0x1000, 0x166f, 0x0,
+			      0x1000, 0x7483, 0x7a7f,
+			      0x1000, 0x0, 0x1c5a };
+	u16 sdtv_coeffs_yonly[] = { 0x0, 0x0, 0x1000,
+				    0x0, 0x0, 0x1000,
+				    0x0, 0x0, 0x1000 };
+	u16 swap_coeffs[] = { 0x1000, 0x0, 0x0,
+			      0x0, 0x1000, 0x0,
+			      0x0, 0x0, 0x1000 };
+	u16 null_coeffs[] = { 0x0, 0x0, 0x0,
+			      0x0, 0x0, 0x0,
+			      0x0, 0x0, 0x0 };
+	u16 *coeffs;
+	u32 sdtv_offsets[] = { 0x0, 0x1800, 0x1800 };
+	u32 sdtv_offsets_yonly[] = { 0x1800, 0x1800, 0x0 };
+	u32 null_offsets[] = { 0x0, 0x0, 0x0 };
+	u32 *offsets;
+	struct zynqmp_disp *display = layer->disp;
+
+	if (layer->id == ZYNQMP_DISP_LAYER_VID)
+		offset = ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF0;
+	else
+		offset = ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF0;
+
+	if (!on) {
+		coeffs = null_coeffs;
+		offsets = null_offsets;
+	} else {
+		if ((!layer->fmt->rgb) && (!display->tpg_on)) {
+			/*
+			 * In case of Y_ONLY formats, pixels are unpacked
+			 * differently compared to YCbCr
+			 */
+			if (layer->fmt->drm_fmt == DRM_FORMAT_Y8 ||
+			    layer->fmt->drm_fmt == DRM_FORMAT_Y10) {
+				coeffs = sdtv_coeffs_yonly;
+				offsets = sdtv_offsets_yonly;
+			} else {
+				coeffs = sdtv_coeffs;
+				offsets = sdtv_offsets;
+			}
+
+			s0 = 1;
+			s1 = 2;
+		} else {
+			coeffs = swap_coeffs;
+			s0 = 0;
+			s1 = 2;
+
+			/* No offset for RGB formats */
+			offsets = null_offsets;
+		}
+
+		if (layer->fmt->swap) {
+			for (i = 0; i < 3; i++) {
+				coeffs[i * 3 + s0] ^= coeffs[i * 3 + s1];
+				coeffs[i * 3 + s1] ^= coeffs[i * 3 + s0];
+				coeffs[i * 3 + s0] ^= coeffs[i * 3 + s1];
+			}
+		}
+	}
+
+	/* Program coefficients. Can be runtime configurable */
+	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i++)
+		zynqmp_disp_write(blend->base, offset + i * 4, coeffs[i]);
+
+	if (layer->id == ZYNQMP_DISP_LAYER_VID)
+		offset = ZYNQMP_DISP_V_BLEND_LUMA_IN1CSC_OFFSET;
+	else
+		offset = ZYNQMP_DISP_V_BLEND_LUMA_IN2CSC_OFFSET;
+
+	/* Program offsets. Can be runtime configurable */
+	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
+		zynqmp_disp_write(blend->base, offset + i * 4, offsets[i]);
+}
+
+/**
+ * zynqmp_disp_blend_layer_enable - Enable a layer
+ * @blend: blend object
+ * @layer: layer to enable
+ *
+ * Enable a layer @layer.
+ */
+static void zynqmp_disp_blend_layer_enable(struct zynqmp_disp_blend *blend,
+					   struct zynqmp_disp_layer *layer)
+{
+	u32 reg;
+
+	reg = layer->fmt->rgb ? ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_RGB : 0;
+	reg |= layer->fmt->chroma_sub ?
+	       ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_EN_US : 0;
+
+	zynqmp_disp_write(blend->base,
+			  ZYNQMP_DISP_V_BLEND_LAYER_CONTROL + layer->offset,
+			  reg);
+
+	zynqmp_disp_blend_layer_coeff(blend, layer, true);
+}
+
+/**
+ * zynqmp_disp_blend_layer_disable - Disable a layer
+ * @blend: blend object
+ * @layer: layer to disable
+ *
+ * Disable a layer @layer.
+ */
+static void zynqmp_disp_blend_layer_disable(struct zynqmp_disp_blend *blend,
+					    struct zynqmp_disp_layer *layer)
+{
+	zynqmp_disp_write(blend->base,
+			  ZYNQMP_DISP_V_BLEND_LAYER_CONTROL + layer->offset, 0);
+
+	zynqmp_disp_blend_layer_coeff(blend, layer, false);
+}
+
+/**
+ * zynqmp_disp_blend_set_bg_color - Set the background color
+ * @blend: blend object
+ * @c0: color component 0
+ * @c1: color component 1
+ * @c2: color component 2
+ *
+ * Set the background color.
+ */
+static void zynqmp_disp_blend_set_bg_color(struct zynqmp_disp_blend *blend,
+					   u32 c0, u32 c1, u32 c2)
+{
+	zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_BG_CLR_0, c0);
+	zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_BG_CLR_1, c1);
+	zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_BG_CLR_2, c2);
+}
+
+/**
+ * zynqmp_disp_blend_set_alpha - Set the alpha for blending
+ * @blend: blend object
+ * @alpha: alpha value to be used
+ *
+ * Set the alpha for blending.
+ */
+static void
+zynqmp_disp_blend_set_alpha(struct zynqmp_disp_blend *blend, u32 alpha)
+{
+	u32 reg;
+
+	reg = zynqmp_disp_read(blend->base,
+			       ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA);
+	reg &= ~ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MASK;
+	reg |= alpha << 1;
+	zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA,
+			  reg);
+}
+
+/**
+ * zynqmp_disp_blend_enable_alpha - Enable/disable the global alpha
+ * @blend: blend object
+ * @enable: flag to enable or disable alpha blending
+ *
+ * Enable/disable the global alpha blending based on @enable.
+ */
+static void
+zynqmp_disp_blend_enable_alpha(struct zynqmp_disp_blend *blend, bool enable)
+{
+	if (enable)
+		zynqmp_disp_set(blend->base,
+				ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA, BIT(0));
+	else
+		zynqmp_disp_clr(blend->base,
+				ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA, BIT(0));
+}
+
+/* List of blend output formats */
+/* The id / order should be aligned with zynqmp_disp_color_enum */
+static const struct zynqmp_disp_fmt blend_output_fmts[] = {
+	{
+		.disp_fmt	= ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB,
+	}, {
+		.disp_fmt	= ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR444,
+	}, {
+		.disp_fmt	= ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR422,
+	}, {
+		.disp_fmt	= ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YONLY,
+	}
 };
 
+/*
+ * AV buffer manager functions
+ */
+
 /* List of video layer formats */
-static const struct zynqmp_disp_format avbuf_vid_fmts[] = {
+#define ZYNQMP_DISP_AV_BUF_VID_FMT_YUYV	2
+static const struct zynqmp_disp_fmt av_buf_vid_fmts[] = {
 	{
 		.drm_fmt	= DRM_FORMAT_VYUY,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_UYVY,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YUYV,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YVYU,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YUV422,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YVU422,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YUV444,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YVU444,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_NV16,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_NV61,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+	}, {
+		.drm_fmt	= DRM_FORMAT_Y8,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_MONO,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+	}, {
+		.drm_fmt	= DRM_FORMAT_Y10,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YONLY_10,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_BGR888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_RGB888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_XBGR8888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_XRGB8888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_XBGR2101010,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_101010,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_XRGB2101010,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_101010,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YUV420,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_YVU420,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_NV12,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420,
+		.rgb		= false,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_NV21,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420,
+		.rgb		= false,
 		.swap		= true,
-		.sf		= scaling_factors_888,
-	},
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+	}, {
+		.drm_fmt	= DRM_FORMAT_XV15,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420_10,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+	}, {
+		.drm_fmt	= DRM_FORMAT_XV20,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_10,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+	}, {
+		.drm_fmt	= DRM_FORMAT_X403,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24_10,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+	}
 };
 
 /* List of graphics layer formats */
-static const struct zynqmp_disp_format avbuf_gfx_fmts[] = {
+static const struct zynqmp_disp_fmt av_buf_gfx_fmts[] = {
 	{
 		.drm_fmt	= DRM_FORMAT_ABGR8888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_ARGB8888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_RGBA8888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_BGRA8888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_BGR888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB888,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_RGB888,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_BGR888,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_BGR888,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_888,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_RGBA5551,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_555,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_BGRA5551,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_555,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_RGBA4444,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_444,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_4BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_4BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_4BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_BGRA4444,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_444,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_4BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_4BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_4BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_RGB565,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565,
+		.rgb		= true,
 		.swap		= false,
-		.sf		= scaling_factors_565,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_6BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
 	}, {
 		.drm_fmt	= DRM_FORMAT_BGR565,
-		.buf_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565,
+		.rgb		= true,
 		.swap		= true,
-		.sf		= scaling_factors_565,
-	},
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_6BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_5BIT_SF,
+	}
+};
+
+/* List of live formats */
+/* Format can be combination of color, bpc, and cb-cr order.
+ * - Color: RGB / YUV444 / YUV422 / Y only
+ * - BPC: 6, 8, 10, 12
+ * - Swap: Cb and Cr swap
+ * which can be 32 bus formats. Only list the subset of those for now.
+ */
+static const struct zynqmp_disp_fmt av_buf_live_fmts[] = {
+	{
+		.bus_fmt	= MEDIA_BUS_FMT_RGB666_1X18,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_6 |
+				  ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB,
+		.rgb		= true,
+		.swap		= false,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_6BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_6BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_6BIT_SF,
+	}, {
+		.bus_fmt	= MEDIA_BUS_FMT_RBG888_1X24,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 |
+				  ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB,
+		.rgb		= true,
+		.swap		= false,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+	}, {
+		.bus_fmt	= MEDIA_BUS_FMT_UYVY8_1X16,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 |
+				  ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+	}, {
+		.bus_fmt	= MEDIA_BUS_FMT_VUY8_1X24,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 |
+				  ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV444,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= false,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_8BIT_SF,
+	}, {
+		.bus_fmt	= MEDIA_BUS_FMT_UYVY10_1X20,
+		.disp_fmt	= ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_10 |
+				  ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422,
+		.rgb		= false,
+		.swap		= false,
+		.chroma_sub	= true,
+		.sf[0]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[1]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+		.sf[2]		= ZYNQMP_DISP_AV_BUF_10BIT_SF,
+	}
 };
 
-static u32 zynqmp_disp_avbuf_read(struct zynqmp_disp *disp, int reg)
+/**
+ * zynqmp_disp_av_buf_set_fmt - Set the input formats
+ * @av_buf: av buffer manager
+ * @fmt: formats
+ *
+ * Set the av buffer manager format to @fmt. @fmt should have valid values
+ * for both video and graphics layer.
+ */
+static void
+zynqmp_disp_av_buf_set_fmt(struct zynqmp_disp_av_buf *av_buf, u32 fmt)
 {
-	return readl(disp->avbuf.base + reg);
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_FMT, fmt);
 }
 
-static void zynqmp_disp_avbuf_write(struct zynqmp_disp *disp, int reg, u32 val)
+/**
+ * zynqmp_disp_av_buf_get_fmt - Get the input formats
+ * @av_buf: av buffer manager
+ *
+ * Get the input formats (which include video and graphics) of
+ * av buffer manager.
+ *
+ * Return: value of ZYNQMP_DISP_AV_BUF_FMT register.
+ */
+static u32
+zynqmp_disp_av_buf_get_fmt(struct zynqmp_disp_av_buf *av_buf)
 {
-	writel(val, disp->avbuf.base + reg);
+	return zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_FMT);
 }
 
-static bool zynqmp_disp_layer_is_gfx(const struct zynqmp_disp_layer *layer)
+/**
+ * zynqmp_disp_av_buf_set_live_fmt - Set the live_input format
+ * @av_buf: av buffer manager
+ * @fmt: format
+ * @is_vid: if it's for video layer
+ *
+ * Set the live input format to @fmt. @fmt should have valid values.
+ * @vid will determine if it's for video layer or graphics layer
+ * @fmt should be a valid hardware value.
+ */
+static void zynqmp_disp_av_buf_set_live_fmt(struct zynqmp_disp_av_buf *av_buf,
+					    u32 fmt, bool is_vid)
 {
-	return layer->id == ZYNQMP_DISP_LAYER_GFX;
+	u32 offset;
+
+	if (is_vid)
+		offset = ZYNQMP_DISP_AV_BUF_LIVE_VID_CONFIG;
+	else
+		offset = ZYNQMP_DISP_AV_BUF_LIVE_GFX_CONFIG;
+
+	zynqmp_disp_write(av_buf->base, offset, fmt);
 }
 
-static bool zynqmp_disp_layer_is_video(const struct zynqmp_disp_layer *layer)
+/**
+ * zynqmp_disp_av_buf_set_vid_clock_src - Set the video clock source
+ * @av_buf: av buffer manager
+ * @from_ps: flag if the video clock is from ps
+ *
+ * Set the video clock source based on @from_ps. It can come from either PS or
+ * PL.
+ */
+static void
+zynqmp_disp_av_buf_set_vid_clock_src(struct zynqmp_disp_av_buf *av_buf,
+				     bool from_ps)
 {
-	return layer->id == ZYNQMP_DISP_LAYER_VID;
+	u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
+
+	if (from_ps)
+		reg |= ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS;
+	else
+		reg &= ~ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_set_format - Set the input format for a layer
- * @disp: Display controller
- * @layer: The layer
- * @fmt: The format information
+ * zynqmp_disp_av_buf_vid_clock_src_is_ps - if ps clock is used
+ * @av_buf: av buffer manager
  *
- * Set the video buffer manager format for @layer to @fmt.
+ * Return: if ps clock is used
  */
-static void zynqmp_disp_avbuf_set_format(struct zynqmp_disp *disp,
-					 struct zynqmp_disp_layer *layer,
-					 const struct zynqmp_disp_format *fmt)
+static bool
+zynqmp_disp_av_buf_vid_clock_src_is_ps(struct zynqmp_disp_av_buf *av_buf)
 {
-	unsigned int i;
-	u32 val;
+	u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
 
-	val = zynqmp_disp_avbuf_read(disp, ZYNQMP_DISP_AV_BUF_FMT);
-	val &= zynqmp_disp_layer_is_video(layer)
-	    ? ~ZYNQMP_DISP_AV_BUF_FMT_NL_VID_MASK
-	    : ~ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_MASK;
-	val |= fmt->buf_fmt;
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_FMT, val);
+	return !!(reg & ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS);
+}
 
-	for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_SF; i++) {
-		unsigned int reg = zynqmp_disp_layer_is_video(layer)
-				 ? ZYNQMP_DISP_AV_BUF_VID_COMP_SF(i)
-				 : ZYNQMP_DISP_AV_BUF_GFX_COMP_SF(i);
+/**
+ * zynqmp_disp_av_buf_set_vid_timing_src - Set the video timing source
+ * @av_buf: av buffer manager
+ * @internal: flag if the video timing is generated internally
+ *
+ * Set the video timing source based on @internal. It can come externally or
+ * be generated internally.
+ */
+static void
+zynqmp_disp_av_buf_set_vid_timing_src(struct zynqmp_disp_av_buf *av_buf,
+				      bool internal)
+{
+	u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
 
-		zynqmp_disp_avbuf_write(disp, reg, fmt->sf[i]);
-	}
+	if (internal)
+		reg |= ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING;
+	else
+		reg &= ~ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_set_clocks_sources - Set the clocks sources
- * @disp: Display controller
- * @video_from_ps: True if the video clock originates from the PS
- * @audio_from_ps: True if the audio clock originates from the PS
- * @timings_internal: True if video timings are generated internally
+ * zynqmp_disp_av_buf_vid_timing_src_is_int - if internal timing is used
+ * @av_buf: av buffer manager
  *
- * Set the source for the video and audio clocks, as well as for the video
- * timings. Clocks can originate from the PS or PL, and timings can be
- * generated internally or externally.
+ * Return: if the internal timing is used
  */
-static void
-zynqmp_disp_avbuf_set_clocks_sources(struct zynqmp_disp *disp,
-				     bool video_from_ps, bool audio_from_ps,
-				     bool timings_internal)
+static bool
+zynqmp_disp_av_buf_vid_timing_src_is_int(struct zynqmp_disp_av_buf *av_buf)
 {
-	u32 val = 0;
+	u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
+
+	return !!(reg & ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING);
+}
 
-	if (video_from_ps)
-		val |= ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS;
-	if (audio_from_ps)
-		val |= ZYNQMP_DISP_AV_BUF_CLK_SRC_AUD_FROM_PS;
-	if (timings_internal)
-		val |= ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING;
+/**
+ * zynqmp_disp_av_buf_set_aud_clock_src - Set the audio clock source
+ * @av_buf: av buffer manager
+ * @from_ps: flag if the video clock is from ps
+ *
+ * Set the audio clock source based on @from_ps. It can come from either PS or
+ * PL.
+ */
+static void
+zynqmp_disp_av_buf_set_aud_clock_src(struct zynqmp_disp_av_buf *av_buf,
+				     bool from_ps)
+{
+	u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
 
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_CLK_SRC, val);
+	if (from_ps)
+		reg |= ZYNQMP_DISP_AV_BUF_CLK_SRC_AUD_FROM_PS;
+	else
+		reg &= ~ZYNQMP_DISP_AV_BUF_CLK_SRC_AUD_FROM_PS;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_enable_channels - Enable buffer channels
- * @disp: Display controller
+ * zynqmp_disp_av_buf_enable_buf - Enable buffers
+ * @av_buf: av buffer manager
  *
- * Enable all (video and audio) buffer channels.
+ * Enable all (video and audio) buffers.
  */
-static void zynqmp_disp_avbuf_enable_channels(struct zynqmp_disp *disp)
+static void
+zynqmp_disp_av_buf_enable_buf(struct zynqmp_disp_av_buf *av_buf)
 {
-	unsigned int i;
-	u32 val;
+	u32 reg, i;
 
-	val = ZYNQMP_DISP_AV_BUF_CHBUF_EN |
-	      (ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_MAX <<
-	       ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT);
+	reg = ZYNQMP_DISP_AV_BUF_CHBUF_EN;
+	reg |= ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_MAX <<
+	       ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT;
 
 	for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_VID_GFX_BUFFERS; i++)
-		zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_CHBUF(i),
-					val);
+		zynqmp_disp_write(av_buf->base,
+				  ZYNQMP_DISP_AV_BUF_CHBUF + i * 4, reg);
 
-	val = ZYNQMP_DISP_AV_BUF_CHBUF_EN |
-	      (ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_AUD_MAX <<
-	       ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT);
+	reg = ZYNQMP_DISP_AV_BUF_CHBUF_EN;
+	reg |= ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_AUD_MAX <<
+	       ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT;
 
 	for (; i < ZYNQMP_DISP_AV_BUF_NUM_BUFFERS; i++)
-		zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_CHBUF(i),
-					val);
+		zynqmp_disp_write(av_buf->base,
+				  ZYNQMP_DISP_AV_BUF_CHBUF + i * 4, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_disable_channels - Disable buffer channels
- * @disp: Display controller
+ * zynqmp_disp_av_buf_disable_buf - Disable buffers
+ * @av_buf: av buffer manager
  *
- * Disable all (video and audio) buffer channels.
+ * Disable all (video and audio) buffers.
  */
-static void zynqmp_disp_avbuf_disable_channels(struct zynqmp_disp *disp)
+static void
+zynqmp_disp_av_buf_disable_buf(struct zynqmp_disp_av_buf *av_buf)
 {
-	unsigned int i;
+	u32 reg, i;
 
+	reg = ZYNQMP_DISP_AV_BUF_CHBUF_FLUSH & ~ZYNQMP_DISP_AV_BUF_CHBUF_EN;
 	for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_BUFFERS; i++)
-		zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_CHBUF(i),
-					ZYNQMP_DISP_AV_BUF_CHBUF_FLUSH);
+		zynqmp_disp_write(av_buf->base,
+				  ZYNQMP_DISP_AV_BUF_CHBUF + i * 4, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_enable_aud - Enable audio
+ * @av_buf: av buffer manager
+ *
+ * Enable all audio buffers.
+ */
+static void
+zynqmp_disp_av_buf_enable_aud(struct zynqmp_disp_av_buf *av_buf)
+{
+	u32 reg;
+
+	reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+	reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK;
+	reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MEM;
+	reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_enable_audio - Enable audio
- * @disp: Display controller
+ * zynqmp_disp_av_buf_enable - Enable the video pipe
+ * @av_buf: av buffer manager
  *
- * Enable all audio buffers with a non-live (memory) source.
+ * De-assert the video pipe reset
  */
-static void zynqmp_disp_avbuf_enable_audio(struct zynqmp_disp *disp)
+static void
+zynqmp_disp_av_buf_enable(struct zynqmp_disp_av_buf *av_buf)
 {
-	u32 val;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_SRST_REG, 0);
+}
 
-	val = zynqmp_disp_avbuf_read(disp, ZYNQMP_DISP_AV_BUF_OUTPUT);
-	val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK;
-	val |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MEM;
-	val |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN;
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_OUTPUT, val);
+/**
+ * zynqmp_disp_av_buf_disable - Disable the video pipe
+ * @av_buf: av buffer manager
+ *
+ * Assert the video pipe reset
+ */
+static void
+zynqmp_disp_av_buf_disable(struct zynqmp_disp_av_buf *av_buf)
+{
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_SRST_REG,
+			  ZYNQMP_DISP_AV_BUF_SRST_REG_VID_RST);
 }
 
 /**
- * zynqmp_disp_avbuf_disable_audio - Disable audio
- * @disp: Display controller
+ * zynqmp_disp_av_buf_disable_aud - Disable audio
+ * @av_buf: av buffer manager
  *
  * Disable all audio buffers.
  */
-static void zynqmp_disp_avbuf_disable_audio(struct zynqmp_disp *disp)
+static void
+zynqmp_disp_av_buf_disable_aud(struct zynqmp_disp_av_buf *av_buf)
+{
+	u32 reg;
+
+	reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+	reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK;
+	reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_DISABLE;
+	reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_set_tpg - Set TPG mode
+ * @av_buf: av buffer manager
+ * @tpg_on: if TPG should be on
+ *
+ * Set the TPG mode based on @tpg_on.
+ */
+static void zynqmp_disp_av_buf_set_tpg(struct zynqmp_disp_av_buf *av_buf,
+				       bool tpg_on)
 {
-	u32 val;
+	u32 reg;
 
-	val = zynqmp_disp_avbuf_read(disp, ZYNQMP_DISP_AV_BUF_OUTPUT);
-	val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK;
-	val |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_DISABLE;
-	val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN;
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_OUTPUT, val);
+	reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+	reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
+	if (tpg_on)
+		reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_PATTERN;
+	else
+		reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_PATTERN;
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_enable_video - Enable a video layer
- * @disp: Display controller
- * @layer: The layer
- * @mode: Operating mode of layer
+ * zynqmp_disp_av_buf_enable_vid - Enable the video layer buffer
+ * @av_buf: av buffer manager
+ * @layer: layer to enable
+ * @mode: operation mode of layer
  *
  * Enable the video/graphics buffer for @layer.
  */
-static void zynqmp_disp_avbuf_enable_video(struct zynqmp_disp *disp,
-					   struct zynqmp_disp_layer *layer,
-					   enum zynqmp_disp_layer_mode mode)
-{
-	u32 val;
-
-	val = zynqmp_disp_avbuf_read(disp, ZYNQMP_DISP_AV_BUF_OUTPUT);
-	if (zynqmp_disp_layer_is_video(layer)) {
-		val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
+static void zynqmp_disp_av_buf_enable_vid(struct zynqmp_disp_av_buf *av_buf,
+					  struct zynqmp_disp_layer *layer,
+					  enum zynqmp_disp_layer_mode mode)
+{
+	u32 reg;
+
+	reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+	if (layer->id == ZYNQMP_DISP_LAYER_VID) {
+		reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
 		if (mode == ZYNQMP_DISP_LAYER_NONLIVE)
-			val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MEM;
+			reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MEM;
 		else
-			val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_LIVE;
+			reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_LIVE;
 	} else {
-		val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK;
-		val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM;
+		reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK;
+		reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM;
 		if (mode == ZYNQMP_DISP_LAYER_NONLIVE)
-			val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM;
+			reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM;
 		else
-			val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_LIVE;
+			reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_LIVE;
 	}
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_OUTPUT, val);
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_disable_video - Disable a video layer
- * @disp: Display controller
- * @layer: The layer
+ * zynqmp_disp_av_buf_disable_vid - Disable the video layer buffer
+ * @av_buf: av buffer manager
+ * @layer: layer to disable
  *
  * Disable the video/graphics buffer for @layer.
  */
-static void zynqmp_disp_avbuf_disable_video(struct zynqmp_disp *disp,
-					    struct zynqmp_disp_layer *layer)
+static void
+zynqmp_disp_av_buf_disable_vid(struct zynqmp_disp_av_buf *av_buf,
+			       struct zynqmp_disp_layer *layer)
 {
-	u32 val;
+	u32 reg;
 
-	val = zynqmp_disp_avbuf_read(disp, ZYNQMP_DISP_AV_BUF_OUTPUT);
-	if (zynqmp_disp_layer_is_video(layer)) {
-		val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
-		val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_NONE;
+	reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+	if (layer->id == ZYNQMP_DISP_LAYER_VID) {
+		reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
+		reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_NONE;
 	} else {
-		val &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK;
-		val |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_DISABLE;
+		reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK;
+		reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_DISABLE;
 	}
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_OUTPUT, val);
+	zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
 }
 
 /**
- * zynqmp_disp_avbuf_enable - Enable the video pipe
- * @disp: Display controller
+ * zynqmp_disp_av_buf_init_sf - Initialize scaling factors
+ * @av_buf: av buffer manager
+ * @vid_fmt: video format descriptor
+ * @gfx_fmt: graphics format descriptor
  *
- * De-assert the video pipe reset.
+ * Initialize scaling factors for both video and graphics layers.
+ * If the format descriptor is NULL, the function skips the programming.
  */
-static void zynqmp_disp_avbuf_enable(struct zynqmp_disp *disp)
+static void zynqmp_disp_av_buf_init_sf(struct zynqmp_disp_av_buf *av_buf,
+				       const struct zynqmp_disp_fmt *vid_fmt,
+				       const struct zynqmp_disp_fmt *gfx_fmt)
 {
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_SRST_REG, 0);
+	unsigned int i;
+	u32 offset;
+
+	if (gfx_fmt) {
+		offset = ZYNQMP_DISP_AV_BUF_GFX_COMP0_SF;
+		for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_SF; i++)
+			zynqmp_disp_write(av_buf->base, offset + i * 4,
+					  gfx_fmt->sf[i]);
+	}
+
+	if (vid_fmt) {
+		offset = ZYNQMP_DISP_AV_BUF_VID_COMP0_SF;
+		for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_SF; i++)
+			zynqmp_disp_write(av_buf->base, offset + i * 4,
+					  vid_fmt->sf[i]);
+	}
 }
 
 /**
- * zynqmp_disp_avbuf_disable - Disable the video pipe
- * @disp: Display controller
+ * zynqmp_disp_av_buf_init_live_sf - Initialize scaling factors for live source
+ * @av_buf: av buffer manager
+ * @fmt: format descriptor
+ * @is_vid: flag if this is for video layer
  *
- * Assert the video pipe reset.
+ * Initialize scaling factors for live source.
  */
-static void zynqmp_disp_avbuf_disable(struct zynqmp_disp *disp)
+static void zynqmp_disp_av_buf_init_live_sf(struct zynqmp_disp_av_buf *av_buf,
+					    const struct zynqmp_disp_fmt *fmt,
+					    bool is_vid)
 {
-	zynqmp_disp_avbuf_write(disp, ZYNQMP_DISP_AV_BUF_SRST_REG,
-				ZYNQMP_DISP_AV_BUF_SRST_REG_VID_RST);
+	unsigned int i;
+	u32 offset;
+
+	if (is_vid)
+		offset = ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP0_SF;
+	else
+		offset = ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP0_SF;
+
+	for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_SF; i++)
+		zynqmp_disp_write(av_buf->base, offset + i * 4,
+				  fmt->sf[i]);
 }
 
-/* -----------------------------------------------------------------------------
- * Blender (Video Pipeline)
+/*
+ * Audio functions
  */
 
-static void zynqmp_disp_blend_write(struct zynqmp_disp *disp, int reg, u32 val)
+/**
+ * zynqmp_disp_aud_init - Initialize the audio
+ * @aud: audio
+ *
+ * Initialize the audio with default mixer volume. The de-assertion will
+ * initialize the audio states.
+ */
+static void zynqmp_disp_aud_init(struct zynqmp_disp_aud *aud)
+{
+	/* Clear the audio soft reset register as it's an non-reset flop */
+	regmap_write(aud->base, ZYNQMP_DISP_AUD_SOFT_RESET, 0);
+	regmap_write(aud->base, ZYNQMP_DISP_AUD_MIXER_VOLUME,
+		     ZYNQMP_DISP_AUD_MIXER_VOLUME_NO_SCALE);
+}
+
+/**
+ * zynqmp_disp_aud_deinit - De-initialize the audio
+ * @aud: audio
+ *
+ * Put the audio in reset.
+ */
+static void zynqmp_disp_aud_deinit(struct zynqmp_disp_aud *aud)
 {
-	writel(val, disp->blend.base + reg);
+	regmap_write_bits(aud->base, ZYNQMP_DISP_AUD_SOFT_RESET,
+			  ZYNQMP_DISP_AUD_SOFT_RESET_AUD_SRST,
+			  ZYNQMP_DISP_AUD_SOFT_RESET_AUD_SRST);
 }
 
 /*
- * Colorspace conversion matrices.
+ * ZynqMP Display layer functions
+ */
+
+/**
+ * zynqmp_disp_layer_check_size - Verify width and height for the layer
+ * @disp: Display subsystem
+ * @layer: layer
+ * @width: width
+ * @height: height
  *
- * Hardcode RGB <-> YUV conversion to full-range SDTV for now.
+ * The Display subsystem has the limitation that both layers should have
+ * identical size. This function stores width and height of @layer, and verifies
+ * if the size (width and height) is valid.
+ *
+ * Return: 0 on success, or -EINVAL if width or/and height is invalid.
  */
-static const u16 csc_zero_matrix[] = {
-	0x0,    0x0,    0x0,
-	0x0,    0x0,    0x0,
-	0x0,    0x0,    0x0
-};
+static int zynqmp_disp_layer_check_size(struct zynqmp_disp *disp,
+					struct zynqmp_disp_layer *layer,
+					u32 width, u32 height)
+{
+	struct zynqmp_disp_layer *other = layer->other;
 
-static const u16 csc_identity_matrix[] = {
-	0x1000, 0x0,    0x0,
-	0x0,    0x1000, 0x0,
-	0x0,    0x0,    0x1000
-};
+	if (other->enabled && (other->w != width || other->h != height)) {
+		dev_err(disp->dev, "Layer width:height must be %d:%d\n",
+			other->w, other->h);
+		return -EINVAL;
+	}
 
-static const u32 csc_zero_offsets[] = {
-	0, 0, 0
-};
+	layer->w = width;
+	layer->h = height;
 
-static const u16 csc_rgb_to_sdtv_matrix[] = {
-	0x4c9,  0x864,  0x1d3,
-	0x7d4d, 0x7ab3, 0x800,
-	0x800,  0x794d, 0x7eb3
-};
+	return 0;
+}
 
-static const u32 csc_rgb_to_sdtv_offsets[] = {
-	0x0, 0x8000000, 0x8000000
-};
+/**
+ * zynqmp_disp_map_fmt - Find the Display subsystem format for given drm format
+ * @fmts: format table to look up
+ * @size: size of the table @fmts
+ * @drm_fmt: DRM format to search
+ *
+ * Search a Display subsystem format corresponding to the given DRM format
+ * @drm_fmt, and return the format descriptor which contains the Display
+ * subsystem format value.
+ *
+ * Return: a Display subsystem format descriptor on success, or NULL.
+ */
+static const struct zynqmp_disp_fmt *
+zynqmp_disp_map_fmt(const struct zynqmp_disp_fmt fmts[],
+		    unsigned int size, uint32_t drm_fmt)
+{
+	unsigned int i;
 
-static const u16 csc_sdtv_to_rgb_matrix[] = {
-	0x1000, 0x166f, 0x0,
-	0x1000, 0x7483, 0x7a7f,
-	0x1000, 0x0,    0x1c5a
-};
+	for (i = 0; i < size; i++)
+		if (fmts[i].drm_fmt == drm_fmt)
+			return &fmts[i];
 
-static const u32 csc_sdtv_to_rgb_offsets[] = {
-	0x0, 0x1800, 0x1800
-};
+	return NULL;
+}
+
+/**
+ * zynqmp_disp_layer_set_fmt - Set the format of the layer
+ * @disp: Display subsystem
+ * @layer: layer to set the format
+ * @drm_fmt: DRM format to set
+ *
+ * Set the format of the given layer to @drm_fmt.
+ *
+ * Return: 0 on success. -EINVAL if @drm_fmt is not supported by the layer.
+ */
+static int zynqmp_disp_layer_set_fmt(struct zynqmp_disp *disp,
+				     struct zynqmp_disp_layer *layer,
+				     uint32_t drm_fmt)
+{
+	const struct zynqmp_disp_fmt *fmt;
+	const struct zynqmp_disp_fmt *vid_fmt = NULL, *gfx_fmt = NULL;
+	u32 size, fmts, mask;
+
+	if (layer->id == ZYNQMP_DISP_LAYER_VID) {
+		size = ARRAY_SIZE(av_buf_vid_fmts);
+		mask = ~ZYNQMP_DISP_AV_BUF_FMT_NL_VID_MASK;
+		fmt = zynqmp_disp_map_fmt(av_buf_vid_fmts, size, drm_fmt);
+		vid_fmt = fmt;
+	} else {
+		size = ARRAY_SIZE(av_buf_gfx_fmts);
+		mask = ~ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_MASK;
+		fmt = zynqmp_disp_map_fmt(av_buf_gfx_fmts, size, drm_fmt);
+		gfx_fmt = fmt;
+	}
+
+	if (!fmt)
+		return -EINVAL;
+
+	fmts = zynqmp_disp_av_buf_get_fmt(&disp->av_buf);
+	fmts &= mask;
+	fmts |= fmt->disp_fmt;
+	zynqmp_disp_av_buf_set_fmt(&disp->av_buf, fmts);
+	zynqmp_disp_av_buf_init_sf(&disp->av_buf, vid_fmt, gfx_fmt);
+	layer->fmt = fmt;
+
+	return 0;
+}
 
 /**
- * zynqmp_disp_blend_set_output_format - Set the output format of the blender
- * @disp: Display controller
- * @format: Output format
- *
- * Set the output format of the blender to @format.
- */
-static void zynqmp_disp_blend_set_output_format(struct zynqmp_disp *disp,
-						enum zynqmp_dpsub_format format)
-{
-	static const unsigned int blend_output_fmts[] = {
-		[ZYNQMP_DPSUB_FORMAT_RGB] = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB,
-		[ZYNQMP_DPSUB_FORMAT_YCRCB444] = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR444,
-		[ZYNQMP_DPSUB_FORMAT_YCRCB422] = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR422
-					       | ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_EN_DOWNSAMPLE,
-		[ZYNQMP_DPSUB_FORMAT_YONLY] = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YONLY,
-	};
-
-	u32 fmt = blend_output_fmts[format];
-	const u16 *coeffs;
-	const u32 *offsets;
+ * zynqmp_disp_map_live_fmt - Find the hardware format for given bus format
+ * @fmts: format table to look up
+ * @size: size of the table @fmts
+ * @bus_fmt: bus format to search
+ *
+ * Search a Display subsystem format corresponding to the given bus format
+ * @bus_fmt, and return the format descriptor which contains the Display
+ * subsystem format value.
+ *
+ * Return: a Display subsystem format descriptor on success, or NULL.
+ */
+static const struct zynqmp_disp_fmt *
+zynqmp_disp_map_live_fmt(const struct zynqmp_disp_fmt fmts[],
+			 unsigned int size, uint32_t bus_fmt)
+{
 	unsigned int i;
 
-	zynqmp_disp_blend_write(disp, ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT, fmt);
-	if (fmt == ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB) {
-		coeffs = csc_identity_matrix;
-		offsets = csc_zero_offsets;
-	} else {
-		coeffs = csc_rgb_to_sdtv_matrix;
-		offsets = csc_rgb_to_sdtv_offsets;
+	for (i = 0; i < size; i++)
+		if (fmts[i].bus_fmt == bus_fmt)
+			return &fmts[i];
+
+	return NULL;
+}
+
+/**
+ * zynqmp_disp_layer_set_live_fmt - Set the live format of the layer
+ * @disp: Display subsystem
+ * @layer: layer to set the format
+ * @bus_fmt: bus format to set
+ *
+ * Set the live format of the given layer to @live_fmt.
+ *
+ * Return: 0 on success. -EINVAL if @bus_fmt is not supported by the layer.
+ */
+static int zynqmp_disp_layer_set_live_fmt(struct zynqmp_disp *disp,
+					  struct zynqmp_disp_layer *layer,
+					  uint32_t bus_fmt)
+{
+	const struct zynqmp_disp_fmt *fmt;
+	u32 size;
+	bool is_vid = layer->id == ZYNQMP_DISP_LAYER_VID;
+
+	size = ARRAY_SIZE(av_buf_live_fmts);
+	fmt = zynqmp_disp_map_live_fmt(av_buf_live_fmts, size, bus_fmt);
+	if (!fmt)
+		return -EINVAL;
+
+	zynqmp_disp_av_buf_set_live_fmt(&disp->av_buf, fmt->disp_fmt, is_vid);
+	zynqmp_disp_av_buf_init_live_sf(&disp->av_buf, fmt, is_vid);
+	layer->fmt = fmt;
+
+	return 0;
+}
+
+/**
+ * zynqmp_disp_layer_set_tpg - Enable or disable TPG
+ * @disp: Display subsystem
+ * @layer: Video layer
+ * @tpg_on: flag if TPG needs to be enabled or disabled
+ *
+ * Enable / disable the TPG mode on the video layer @layer depending on
+ * @tpg_on. The video layer should be disabled prior to enable request.
+ *
+ * Return: 0 on success. -ENODEV if it's not video layer. -EIO if
+ * the video layer is enabled.
+ */
+static int zynqmp_disp_layer_set_tpg(struct zynqmp_disp *disp,
+				     struct zynqmp_disp_layer *layer,
+				     bool tpg_on)
+{
+	if (layer->id != ZYNQMP_DISP_LAYER_VID) {
+		dev_err(disp->dev,
+			"only the video layer has the tpg mode\n");
+		return -ENODEV;
 	}
 
-	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i++)
-		zynqmp_disp_blend_write(disp,
-					ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF(i),
-					coeffs[i]);
+	if (layer->enabled) {
+		dev_err(disp->dev,
+			"the video layer should be disabled for tpg mode\n");
+		return -EIO;
+	}
 
-	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
-		zynqmp_disp_blend_write(disp,
-					ZYNQMP_DISP_V_BLEND_OUTCSC_OFFSET(i),
-					offsets[i]);
+	disp->tpg_on = tpg_on;
+	zynqmp_disp_av_buf_set_tpg(&disp->av_buf, tpg_on);
+
+	return 0;
 }
 
 /**
- * zynqmp_disp_blend_set_bg_color - Set the background color
- * @disp: Display controller
- * @rcr: Red/Cr color component
- * @gy: Green/Y color component
- * @bcb: Blue/Cb color component
+ * zynqmp_disp_layer_get_tpg - Get the TPG mode status
+ * @disp: Display subsystem
+ * @layer: Video layer
+ *
+ * Return if the TPG is enabled or not.
  *
- * Set the background color to (@rcr, @gy, @bcb), corresponding to the R, G and
- * B or Cr, Y and Cb components respectively depending on the selected output
- * format.
+ * Return: true if TPG is on, otherwise false
  */
-static void zynqmp_disp_blend_set_bg_color(struct zynqmp_disp *disp,
-					   u32 rcr, u32 gy, u32 bcb)
+static bool zynqmp_disp_layer_get_tpg(struct zynqmp_disp *disp,
+				      struct zynqmp_disp_layer *layer)
 {
-	zynqmp_disp_blend_write(disp, ZYNQMP_DISP_V_BLEND_BG_CLR_0, rcr);
-	zynqmp_disp_blend_write(disp, ZYNQMP_DISP_V_BLEND_BG_CLR_1, gy);
-	zynqmp_disp_blend_write(disp, ZYNQMP_DISP_V_BLEND_BG_CLR_2, bcb);
+	return disp->tpg_on;
 }
 
 /**
- * zynqmp_disp_blend_set_global_alpha - Configure global alpha blending
- * @disp: Display controller
- * @enable: True to enable global alpha blending
- * @alpha: Global alpha value (ignored if @enabled is false)
+ * zynqmp_disp_layer_get_fmts - Get the supported DRM formats of the layer
+ * @disp: Display subsystem
+ * @layer: layer to get the formats
+ * @drm_fmts: pointer to array of DRM format strings
+ * @num_fmts: pointer to number of returned DRM formats
+ *
+ * Get the supported DRM formats of the given layer.
  */
-static void zynqmp_disp_blend_set_global_alpha(struct zynqmp_disp *disp,
-					       bool enable, u32 alpha)
+static void zynqmp_disp_layer_get_fmts(struct zynqmp_disp *disp,
+				       struct zynqmp_disp_layer *layer,
+				       u32 **drm_fmts, unsigned int *num_fmts)
 {
-	zynqmp_disp_blend_write(disp, ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA,
-				ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_VALUE(alpha) |
-				(enable ? ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_EN : 0));
+	*drm_fmts = layer->drm_fmts;
+	*num_fmts = layer->num_fmts;
 }
 
 /**
- * zynqmp_disp_blend_layer_set_csc - Configure colorspace conversion for layer
- * @disp: Display controller
- * @layer: The layer
- * @coeffs: Colorspace conversion matrix
- * @offsets: Colorspace conversion offsets
+ * zynqmp_disp_layer_enable - Enable the layer
+ * @disp: Display subsystem
+ * @layer: layer to esable
+ * @mode: operation mode
+ *
+ * Enable the layer @layer.
  *
- * Configure the input colorspace conversion matrix and offsets for the @layer.
- * Columns of the matrix are automatically swapped based on the input format to
- * handle RGB and YCrCb components permutations.
+ * Return: 0 on success, otherwise error code.
  */
-static void zynqmp_disp_blend_layer_set_csc(struct zynqmp_disp *disp,
-					    struct zynqmp_disp_layer *layer,
-					    const u16 *coeffs,
-					    const u32 *offsets)
+static int zynqmp_disp_layer_enable(struct zynqmp_disp *disp,
+				    struct zynqmp_disp_layer *layer,
+				    enum zynqmp_disp_layer_mode mode)
 {
-	unsigned int swap[3] = { 0, 1, 2 };
-	unsigned int reg;
+	struct device *dev = disp->dev;
+	struct dma_async_tx_descriptor *desc;
+	unsigned long flags;
 	unsigned int i;
 
-	if (layer->disp_fmt->swap) {
-		if (layer->drm_fmt->is_yuv) {
-			/* Swap U and V. */
-			swap[1] = 2;
-			swap[2] = 1;
-		} else {
-			/* Swap R and B. */
-			swap[0] = 2;
-			swap[2] = 0;
+	if (layer->enabled && layer->mode != mode) {
+		dev_err(dev, "layer is already enabled in different mode\n");
+		return -EBUSY;
+	}
+
+	zynqmp_disp_av_buf_enable_vid(&disp->av_buf, layer, mode);
+	zynqmp_disp_blend_layer_enable(&disp->blend, layer);
+
+	layer->enabled = true;
+	layer->mode = mode;
+
+	if (mode == ZYNQMP_DISP_LAYER_LIVE)
+		return 0;
+
+	for (i = 0; i < ZYNQMP_DISP_MAX_NUM_SUB_PLANES; i++) {
+		struct zynqmp_disp_layer_dma *dma = &layer->dma[i];
+
+		if (dma->chan && dma->is_active) {
+			flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT | DMA_PREP_REPEAT |
+				DMA_PREP_LOAD_EOT;
+			desc = dmaengine_prep_interleaved_dma(dma->chan,
+							      &dma->xt, flags);
+			if (!desc) {
+				dev_err(dev, "failed to prep DMA descriptor\n");
+				return -ENOMEM;
+			}
+
+			dmaengine_submit(desc);
+			dma_async_issue_pending(dma->chan);
 		}
 	}
 
-	if (zynqmp_disp_layer_is_video(layer))
-		reg = ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF(0);
-	else
-		reg = ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF(0);
+	return 0;
+}
+
+/**
+ * zynqmp_disp_layer_disable - Disable the layer
+ * @disp: Display subsystem
+ * @layer: layer to disable
+ * @mode: operation mode
+ *
+ * Disable the layer @layer.
+ *
+ * Return: 0 on success, or -EBUSY if the layer is in different mode.
+ */
+static int zynqmp_disp_layer_disable(struct zynqmp_disp *disp,
+				     struct zynqmp_disp_layer *layer,
+				     enum zynqmp_disp_layer_mode mode)
+{
+	struct device *dev = disp->dev;
+	unsigned int i;
 
-	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i += 3, reg += 12) {
-		zynqmp_disp_blend_write(disp, reg + 0, coeffs[i + swap[0]]);
-		zynqmp_disp_blend_write(disp, reg + 4, coeffs[i + swap[1]]);
-		zynqmp_disp_blend_write(disp, reg + 8, coeffs[i + swap[2]]);
+	if (layer->mode != mode) {
+		dev_err(dev, "the layer is operating in different mode\n");
+		return -EBUSY;
 	}
 
-	if (zynqmp_disp_layer_is_video(layer))
-		reg = ZYNQMP_DISP_V_BLEND_IN1CSC_OFFSET(0);
-	else
-		reg = ZYNQMP_DISP_V_BLEND_IN2CSC_OFFSET(0);
+	for (i = 0; i < ZYNQMP_DISP_MAX_NUM_SUB_PLANES; i++)
+		if (layer->dma[i].chan && layer->dma[i].is_active)
+			dmaengine_terminate_sync(layer->dma[i].chan);
+
+	zynqmp_disp_av_buf_disable_vid(&disp->av_buf, layer);
+	zynqmp_disp_blend_layer_disable(&disp->blend, layer);
+	layer->enabled = false;
 
-	for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
-		zynqmp_disp_blend_write(disp, reg + i * 4, offsets[i]);
+	return 0;
 }
 
 /**
- * zynqmp_disp_blend_layer_enable - Enable a layer
- * @disp: Display controller
- * @layer: The layer
+ * zynqmp_disp_layer_request_dma - Request DMA channels for a layer
+ * @disp: Display subsystem
+ * @layer: layer to request DMA channels
+ * @name: identifier string for layer type
+ *
+ * Request DMA engine channels for corresponding layer.
+ *
+ * Return: 0 on success, or err value from of_dma_request_slave_channel().
  */
-static void zynqmp_disp_blend_layer_enable(struct zynqmp_disp *disp,
-					   struct zynqmp_disp_layer *layer)
+static int
+zynqmp_disp_layer_request_dma(struct zynqmp_disp *disp,
+			      struct zynqmp_disp_layer *layer, const char *name)
 {
-	const u16 *coeffs;
-	const u32 *offsets;
-	u32 val;
-
-	val = (layer->drm_fmt->is_yuv ?
-	       0 : ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_RGB) |
-	      (layer->drm_fmt->hsub > 1 ?
-	       ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_EN_US : 0);
-
-	zynqmp_disp_blend_write(disp,
-				ZYNQMP_DISP_V_BLEND_LAYER_CONTROL(layer->id),
-				val);
-
-	if (layer->drm_fmt->is_yuv) {
-		coeffs = csc_sdtv_to_rgb_matrix;
-		offsets = csc_sdtv_to_rgb_offsets;
-	} else {
-		coeffs = csc_identity_matrix;
-		offsets = csc_zero_offsets;
+	struct zynqmp_disp_layer_dma *dma;
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < layer->num_chan; i++) {
+		char temp[16];
+
+		dma = &layer->dma[i];
+		snprintf(temp, sizeof(temp), "%s%d", name, i);
+		dma->chan = of_dma_request_slave_channel(disp->dev->of_node,
+							 temp);
+		if (IS_ERR(dma->chan)) {
+			dev_err(disp->dev, "failed to request dma channel\n");
+			ret = PTR_ERR(dma->chan);
+			dma->chan = NULL;
+			return ret;
+		}
 	}
 
-	zynqmp_disp_blend_layer_set_csc(disp, layer, coeffs, offsets);
+	return 0;
 }
 
 /**
- * zynqmp_disp_blend_layer_disable - Disable a layer
- * @disp: Display controller
- * @layer: The layer
+ * zynqmp_disp_layer_release_dma - Release DMA channels for a layer
+ * @disp: Display subsystem
+ * @layer: layer to release DMA channels
+ *
+ * Release the dma channels associated with @layer.
  */
-static void zynqmp_disp_blend_layer_disable(struct zynqmp_disp *disp,
-					    struct zynqmp_disp_layer *layer)
+static void zynqmp_disp_layer_release_dma(struct zynqmp_disp *disp,
+					  struct zynqmp_disp_layer *layer)
 {
-	zynqmp_disp_blend_write(disp,
-				ZYNQMP_DISP_V_BLEND_LAYER_CONTROL(layer->id),
-				0);
+	unsigned int i;
 
-	zynqmp_disp_blend_layer_set_csc(disp, layer, csc_zero_matrix,
-					csc_zero_offsets);
+	for (i = 0; i < layer->num_chan; i++) {
+		if (layer->dma[i].chan) {
+			/* Make sure the channel is terminated before release */
+			dmaengine_terminate_all(layer->dma[i].chan);
+			dma_release_channel(layer->dma[i].chan);
+		}
+	}
 }
 
-/* -----------------------------------------------------------------------------
- * Audio Mixer
+/**
+ * zynqmp_disp_layer_is_live - if any layer is live
+ * @disp: Display subsystem
+ *
+ * Return: true if any layer is live
  */
-
-static void zynqmp_disp_audio_write(struct zynqmp_disp *disp, int reg, u32 val)
+static bool zynqmp_disp_layer_is_live(struct zynqmp_disp *disp)
 {
-	writel(val, disp->audio.base + reg);
+	unsigned int i;
+
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+		if (disp->layers[i].enabled &&
+		    disp->layers[i].mode == ZYNQMP_DISP_LAYER_LIVE)
+			return true;
+	}
+
+	return false;
 }
 
 /**
- * zynqmp_disp_audio_enable - Enable the audio mixer
- * @disp: Display controller
+ * zynqmp_disp_layer_is_enabled - if any layer is enabled
+ * @disp: Display subsystem
  *
- * Enable the audio mixer by de-asserting the soft reset. The audio state is set to
- * default values by the reset, set the default mixer volume explicitly.
+ * Return: true if any layer is enabled
  */
-static void zynqmp_disp_audio_enable(struct zynqmp_disp *disp)
+static bool zynqmp_disp_layer_is_enabled(struct zynqmp_disp *disp)
 {
-	/* Clear the audio soft reset register as it's an non-reset flop. */
-	zynqmp_disp_audio_write(disp, ZYNQMP_DISP_AUD_SOFT_RESET, 0);
-	zynqmp_disp_audio_write(disp, ZYNQMP_DISP_AUD_MIXER_VOLUME,
-				ZYNQMP_DISP_AUD_MIXER_VOLUME_NO_SCALE);
+	unsigned int i;
+
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
+		if (disp->layers[i].enabled)
+			return true;
+
+	return false;
 }
 
 /**
- * zynqmp_disp_audio_disable - Disable the audio mixer
- * @disp: Display controller
+ * zynqmp_disp_layer_destroy - Destroy all layers
+ * @disp: Display subsystem
  *
- * Disable the audio mixer by asserting its soft reset.
+ * Destroy all layers.
  */
-static void zynqmp_disp_audio_disable(struct zynqmp_disp *disp)
+static void zynqmp_disp_layer_destroy(struct zynqmp_disp *disp)
 {
-	zynqmp_disp_audio_write(disp, ZYNQMP_DISP_AUD_SOFT_RESET,
-				ZYNQMP_DISP_AUD_SOFT_RESET_AUD_SRST);
+	unsigned int i;
+
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
+		zynqmp_disp_layer_release_dma(disp, &disp->layers[i]);
 }
 
-static void zynqmp_disp_audio_init(struct zynqmp_disp *disp)
+/**
+ * zynqmp_disp_layer_create - Create all layers
+ * @disp: Display subsystem
+ *
+ * Create all layers.
+ *
+ * Return: 0 on success, otherwise error code from failed function
+ */
+static int zynqmp_disp_layer_create(struct zynqmp_disp *disp)
 {
-	/* Try the live PL audio clock. */
-	disp->audio.clk = devm_clk_get(disp->dev, "dp_live_audio_aclk");
-	if (!IS_ERR(disp->audio.clk)) {
-		disp->audio.clk_from_ps = false;
-		return;
-	}
+	struct zynqmp_disp_layer *layer;
+	unsigned int i;
+	int num_chans[ZYNQMP_DISP_NUM_LAYERS] = { 3, 1 };
+	const char * const dma_name[] = { "vid", "gfx" };
+	int ret = -EINVAL;
 
-	/* If the live PL audio clock is not valid, fall back to PS clock. */
-	disp->audio.clk = devm_clk_get(disp->dev, "dp_aud_clk");
-	if (!IS_ERR(disp->audio.clk)) {
-		disp->audio.clk_from_ps = true;
-		return;
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+		layer = &disp->layers[i];
+		layer->id = (enum zynqmp_disp_layer_type)i;
+		layer->offset = i * 4;
+		layer->other = &disp->layers[!i];
+		layer->num_chan = num_chans[i];
+		ret = zynqmp_disp_layer_request_dma(disp, layer, dma_name[i]);
+		if (ret)
+			goto err;
+		layer->disp = disp;
 	}
 
-	dev_err(disp->dev, "audio disabled due to missing clock\n");
+	return 0;
+
+err:
+	zynqmp_disp_layer_destroy(disp);
+	return ret;
 }
 
-/* -----------------------------------------------------------------------------
- * ZynqMP Display external functions for zynqmp_dp
+/*
+ * ZynqMP Display internal functions
  */
 
+/*
+ * Output format enumeration.
+ * The ID should be aligned with blend_output_fmts.
+ * The string should be aligned with how zynqmp_dp_set_color() decodes.
+ */
+static struct drm_prop_enum_list zynqmp_disp_color_enum[] = {
+	{ 0, "rgb" },
+	{ 1, "ycrcb444" },
+	{ 2, "ycrcb422" },
+	{ 3, "yonly" },
+};
+
 /**
- * zynqmp_disp_handle_vblank - Handle the vblank event
- * @disp: Display controller
+ * zynqmp_disp_set_output_fmt - Set the output format
+ * @disp: Display subsystem
+ * @id: the format ID. Refer to zynqmp_disp_color_enum[].
  *
- * This function handles the vblank interrupt, and sends an event to
- * CRTC object. This will be called by the DP vblank interrupt handler.
+ * This function sets the output format of the display / blender as well as
+ * the format of DP controller. The @id should be aligned with
+ * zynqmp_disp_color_enum.
  */
-void zynqmp_disp_handle_vblank(struct zynqmp_disp *disp)
+static void
+zynqmp_disp_set_output_fmt(struct zynqmp_disp *disp, unsigned int id)
 {
-	struct drm_crtc *crtc = &disp->crtc;
+	const struct zynqmp_disp_fmt *fmt = &blend_output_fmts[id];
 
-	drm_crtc_handle_vblank(crtc);
+	zynqmp_dp_set_color(disp->dpsub->dp, zynqmp_disp_color_enum[id].name);
+	zynqmp_disp_blend_set_output_fmt(&disp->blend, fmt->disp_fmt);
 }
 
 /**
- * zynqmp_disp_audio_enabled - If the audio is enabled
- * @disp: Display controller
- *
- * Return if the audio is enabled depending on the audio clock.
+ * zynqmp_disp_set_bg_color - Set the background color
+ * @disp: Display subsystem
+ * @c0: color component 0
+ * @c1: color component 1
+ * @c2: color component 2
  *
- * Return: true if audio is enabled, or false.
+ * Set the background color with given color components (@c0, @c1, @c2).
  */
-bool zynqmp_disp_audio_enabled(struct zynqmp_disp *disp)
+static void zynqmp_disp_set_bg_color(struct zynqmp_disp *disp,
+				     u32 c0, u32 c1, u32 c2)
 {
-	return !!disp->audio.clk;
+	zynqmp_disp_blend_set_bg_color(&disp->blend, c0, c1, c2);
 }
 
 /**
- * zynqmp_disp_get_audio_clk_rate - Get the current audio clock rate
- * @disp: Display controller
+ * zynqmp_disp_set_alpha - Set the alpha value
+ * @disp: Display subsystem
+ * @alpha: alpha value to set
  *
- * Return: the current audio clock rate.
+ * Set the alpha value for blending.
  */
-unsigned int zynqmp_disp_get_audio_clk_rate(struct zynqmp_disp *disp)
+static void zynqmp_disp_set_alpha(struct zynqmp_disp *disp, u32 alpha)
 {
-	if (zynqmp_disp_audio_enabled(disp))
-		return 0;
-	return clk_get_rate(disp->audio.clk);
+	disp->alpha = alpha;
+	zynqmp_disp_blend_set_alpha(&disp->blend, alpha);
 }
 
 /**
- * zynqmp_disp_get_crtc_mask - Return the CRTC bit mask
- * @disp: Display controller
+ * zynqmp_disp_get_alpha - Get the alpha value
+ * @disp: Display subsystem
  *
- * Return: the crtc mask of the zyqnmp_disp CRTC.
+ * Get the alpha value for blending.
+ *
+ * Return: current alpha value.
  */
-uint32_t zynqmp_disp_get_crtc_mask(struct zynqmp_disp *disp)
+static u32 zynqmp_disp_get_alpha(struct zynqmp_disp *disp)
 {
-	return drm_crtc_mask(&disp->crtc);
+	return disp->alpha;
 }
 
-/* -----------------------------------------------------------------------------
- * ZynqMP Display Layer & DRM Plane
+/**
+ * zynqmp_disp_set_g_alpha - Enable/disable the global alpha blending
+ * @disp: Display subsystem
+ * @enable: flag to enable or disable alpha blending
+ *
+ * Set the alpha value for blending.
  */
+static void zynqmp_disp_set_g_alpha(struct zynqmp_disp *disp, bool enable)
+{
+	disp->alpha_en = enable;
+	zynqmp_disp_blend_enable_alpha(&disp->blend, enable);
+}
 
 /**
- * zynqmp_disp_layer_find_format - Find format information for a DRM format
- * @layer: The layer
- * @drm_fmt: DRM format to search
+ * zynqmp_disp_get_g_alpha - Get the global alpha status
+ * @disp: Display subsystem
+ *
+ * Get the global alpha statue.
  *
- * Search display subsystem format information corresponding to the given DRM
- * format @drm_fmt for the @layer, and return a pointer to the format
- * descriptor.
- *
- * Return: A pointer to the format descriptor if found, NULL otherwise
- */
-static const struct zynqmp_disp_format *
-zynqmp_disp_layer_find_format(struct zynqmp_disp_layer *layer,
-			      u32 drm_fmt)
+ * Return: true if global alpha is enabled, or false.
+ */
+static bool zynqmp_disp_get_g_alpha(struct zynqmp_disp *disp)
 {
-	unsigned int i;
-
-	for (i = 0; i < layer->info->num_formats; i++) {
-		if (layer->info->formats[i].drm_fmt == drm_fmt)
-			return &layer->info->formats[i];
-	}
-
-	return NULL;
+	return disp->alpha_en;
 }
 
 /**
- * zynqmp_disp_layer_enable - Enable a layer
- * @layer: The layer
+ * zynqmp_disp_enable - Enable the Display subsystem
+ * @disp: Display subsystem
  *
- * Enable the @layer in the audio/video buffer manager and the blender. DMA
- * channels are started separately by zynqmp_disp_layer_update().
+ * Enable the Display subsystem.
  */
-static void zynqmp_disp_layer_enable(struct zynqmp_disp_layer *layer)
+static void zynqmp_disp_enable(struct zynqmp_disp *disp)
 {
-	zynqmp_disp_avbuf_enable_video(layer->disp, layer,
-				       ZYNQMP_DISP_LAYER_NONLIVE);
-	zynqmp_disp_blend_layer_enable(layer->disp, layer);
+	bool live;
 
-	layer->mode = ZYNQMP_DISP_LAYER_NONLIVE;
+	if (disp->enabled)
+		return;
+
+	zynqmp_disp_av_buf_enable(&disp->av_buf);
+	/* Choose clock source based on the DT clock handle */
+	zynqmp_disp_av_buf_set_vid_clock_src(&disp->av_buf, !!disp->_ps_pclk);
+	zynqmp_disp_av_buf_set_aud_clock_src(&disp->av_buf, !!disp->_ps_audclk);
+	live = zynqmp_disp_layer_is_live(disp);
+	zynqmp_disp_av_buf_set_vid_timing_src(&disp->av_buf, !live);
+	zynqmp_disp_av_buf_enable_buf(&disp->av_buf);
+	zynqmp_disp_av_buf_enable_aud(&disp->av_buf);
+	zynqmp_disp_aud_init(&disp->aud);
+	disp->enabled = true;
 }
 
 /**
- * zynqmp_disp_layer_disable - Disable the layer
- * @layer: The layer
+ * zynqmp_disp_disable - Disable the Display subsystem
+ * @disp: Display subsystem
+ * @force: flag to disable forcefully
  *
- * Disable the layer by stopping its DMA channels and disabling it in the
- * audio/video buffer manager and the blender.
+ * Disable the Display subsystem.
  */
-static void zynqmp_disp_layer_disable(struct zynqmp_disp_layer *layer)
+static void zynqmp_disp_disable(struct zynqmp_disp *disp, bool force)
 {
-	unsigned int i;
+	struct drm_crtc *crtc = &disp->xlnx_crtc.crtc;
+
+	if (!force && (!disp->enabled || zynqmp_disp_layer_is_enabled(disp)))
+		return;
+
+	zynqmp_disp_aud_deinit(&disp->aud);
+	zynqmp_disp_av_buf_disable_aud(&disp->av_buf);
+	zynqmp_disp_av_buf_disable_buf(&disp->av_buf);
+	zynqmp_disp_av_buf_disable(&disp->av_buf);
 
-	for (i = 0; i < layer->drm_fmt->num_planes; i++)
-		dmaengine_terminate_sync(layer->dmas[i].chan);
+	/* Mark the flip is done as crtc is disabled anyway */
+	if (crtc->state->event) {
+		complete_all(crtc->state->event->base.completion);
+		crtc->state->event = NULL;
+	}
 
-	zynqmp_disp_avbuf_disable_video(layer->disp, layer);
-	zynqmp_disp_blend_layer_disable(layer->disp, layer);
+	disp->enabled = false;
 }
 
 /**
- * zynqmp_disp_layer_set_format - Set the layer format
- * @layer: The layer
- * @state: The plane state
+ * zynqmp_disp_init - Initialize the Display subsystem states
+ * @disp: Display subsystem
  *
- * Set the format for @layer based on @state->fb->format. The layer must be
- * disabled.
+ * Some states are not initialized as desired. For example, the output select
+ * register resets to the live source. This function is to initialize
+ * some register states as desired.
  */
-static void zynqmp_disp_layer_set_format(struct zynqmp_disp_layer *layer,
-					 struct drm_plane_state *state)
+static void zynqmp_disp_init(struct zynqmp_disp *disp)
 {
-	const struct drm_format_info *info = state->fb->format;
+	struct zynqmp_disp_layer *layer;
 	unsigned int i;
 
-	layer->disp_fmt = zynqmp_disp_layer_find_format(layer, info->format);
-	layer->drm_fmt = info;
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+		layer = &disp->layers[i];
+		zynqmp_disp_av_buf_disable_vid(&disp->av_buf, layer);
+	}
+}
 
-	zynqmp_disp_avbuf_set_format(layer->disp, layer, layer->disp_fmt);
+/*
+ * ZynqMP Display external functions for zynqmp_dp
+ */
 
-	/*
-	 * Set slave_id for each DMA channel to indicate they're part of a
-	 * video group.
-	 */
-	for (i = 0; i < info->num_planes; i++) {
-		struct zynqmp_disp_layer_dma *dma = &layer->dmas[i];
-		struct dma_slave_config config = {
-			.direction = DMA_MEM_TO_DEV,
-			.slave_id = 1,
-		};
+/**
+ * zynqmp_disp_handle_vblank - Handle the vblank event
+ * @disp: Display subsystem
+ *
+ * This function handles the vblank interrupt, and sends an event to
+ * CRTC object. This will be called by the DP vblank interrupt handler.
+ */
+void zynqmp_disp_handle_vblank(struct zynqmp_disp *disp)
+{
+	struct drm_crtc *crtc = &disp->xlnx_crtc.crtc;
 
-		dmaengine_slave_config(dma->chan, &config);
-	}
+	drm_crtc_handle_vblank(crtc);
 }
 
 /**
- * zynqmp_disp_layer_update - Update the layer framebuffer
- * @layer: The layer
- * @state: The plane state
- *
- * Update the framebuffer for the layer by issuing a new DMA engine transaction
- * for the new framebuffer.
+ * zynqmp_disp_get_apb_clk_rate - Get the current APB clock rate
+ * @disp: Display subsystem
  *
- * Return: 0 on success, or the DMA descriptor failure error otherwise
+ * Return: the current APB clock rate.
  */
-static int zynqmp_disp_layer_update(struct zynqmp_disp_layer *layer,
-				    struct drm_plane_state *state)
+unsigned int zynqmp_disp_get_apb_clk_rate(struct zynqmp_disp *disp)
 {
-	const struct drm_format_info *info = layer->drm_fmt;
-	unsigned int i;
+	return clk_get_rate(disp->aclk);
+}
 
-	for (i = 0; i < layer->drm_fmt->num_planes; i++) {
-		unsigned int width = state->crtc_w / (i ? info->hsub : 1);
-		unsigned int height = state->crtc_h / (i ? info->vsub : 1);
-		struct zynqmp_disp_layer_dma *dma = &layer->dmas[i];
-		struct dma_async_tx_descriptor *desc;
-		dma_addr_t paddr;
-
-		paddr = drm_fb_cma_get_gem_addr(state->fb, state, i);
-
-		dma->xt.numf = height;
-		dma->sgl.size = width * info->cpp[i];
-		dma->sgl.icg = state->fb->pitches[i] - dma->sgl.size;
-		dma->xt.src_start = paddr;
-		dma->xt.frame_size = 1;
-		dma->xt.dir = DMA_MEM_TO_DEV;
-		dma->xt.src_sgl = true;
-		dma->xt.dst_sgl = false;
-
-		desc = dmaengine_prep_interleaved_dma(dma->chan, &dma->xt,
-						      DMA_CTRL_ACK |
-						      DMA_PREP_REPEAT |
-						      DMA_PREP_LOAD_EOT);
-		if (!desc) {
-			dev_err(layer->disp->dev,
-				"failed to prepare DMA descriptor\n");
-			return -ENOMEM;
-		}
+/**
+ * zynqmp_disp_aud_enabled - If the audio is enabled
+ * @disp: Display subsystem
+ *
+ * Return if the audio is enabled depending on the audio clock.
+ *
+ * Return: true if audio is enabled, or false.
+ */
+bool zynqmp_disp_aud_enabled(struct zynqmp_disp *disp)
+{
+	return !!disp->audclk;
+}
 
-		dmaengine_submit(desc);
-		dma_async_issue_pending(dma->chan);
-	}
+/**
+ * zynqmp_disp_get_aud_clk_rate - Get the current audio clock rate
+ * @disp: Display subsystem
+ *
+ * Return: the current audio clock rate.
+ */
+unsigned int zynqmp_disp_get_aud_clk_rate(struct zynqmp_disp *disp)
+{
+	if (zynqmp_disp_aud_enabled(disp))
+		return 0;
+	return clk_get_rate(disp->aclk);
+}
 
-	return 0;
+/**
+ * zynqmp_disp_get_crtc_mask - Return the CRTC bit mask
+ * @disp: Display subsystem
+ *
+ * Return: the crtc mask of the zyqnmp_disp CRTC.
+ */
+uint32_t zynqmp_disp_get_crtc_mask(struct zynqmp_disp *disp)
+{
+	return drm_crtc_mask(&disp->xlnx_crtc.crtc);
 }
 
+/*
+ * DRM plane functions
+ */
+
 static inline struct zynqmp_disp_layer *plane_to_layer(struct drm_plane *plane)
 {
 	return container_of(plane, struct zynqmp_disp_layer, plane);
 }
 
-static int
-zynqmp_disp_plane_atomic_check(struct drm_plane *plane,
-			       struct drm_atomic_state *state)
+static int zynqmp_disp_plane_enable(struct drm_plane *plane)
 {
-	struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state,
-										 plane);
-	struct drm_crtc_state *crtc_state;
+	struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+	struct zynqmp_disp *disp = layer->disp;
+	int ret;
 
-	if (!new_plane_state->crtc)
-		return 0;
+	zynqmp_disp_set_g_alpha(disp, disp->alpha_en);
+	zynqmp_disp_set_alpha(disp, disp->alpha);
+	ret = zynqmp_disp_layer_enable(layer->disp, layer,
+				       ZYNQMP_DISP_LAYER_NONLIVE);
+	if (ret)
+		return ret;
 
-	crtc_state = drm_atomic_get_crtc_state(state, new_plane_state->crtc);
-	if (IS_ERR(crtc_state))
-		return PTR_ERR(crtc_state);
-
-	return drm_atomic_helper_check_plane_state(new_plane_state,
-						   crtc_state,
-						   DRM_PLANE_HELPER_NO_SCALING,
-						   DRM_PLANE_HELPER_NO_SCALING,
-						   false, false);
+	if (layer->id == ZYNQMP_DISP_LAYER_GFX && disp->tpg_on) {
+		layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+		zynqmp_disp_layer_set_tpg(disp, layer, disp->tpg_on);
+	}
+
+	return 0;
 }
 
-static void
-zynqmp_disp_plane_atomic_disable(struct drm_plane *plane,
-				 struct drm_atomic_state *state)
+static int zynqmp_disp_plane_disable(struct drm_plane *plane)
 {
-	struct drm_plane_state *old_state = drm_atomic_get_old_plane_state(state,
-									   plane);
 	struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+	struct zynqmp_disp *disp = layer->disp;
 
-	if (!old_state->fb)
-		return;
-
-	zynqmp_disp_layer_disable(layer);
+	zynqmp_disp_layer_disable(disp, layer, ZYNQMP_DISP_LAYER_NONLIVE);
+	if (layer->id == ZYNQMP_DISP_LAYER_VID && disp->tpg_on)
+		zynqmp_disp_layer_set_tpg(disp, layer, disp->tpg_on);
 
-	if (zynqmp_disp_layer_is_gfx(layer))
-		zynqmp_disp_blend_set_global_alpha(layer->disp, false,
-						   plane->state->alpha >> 8);
+	return 0;
 }
 
-static void
-zynqmp_disp_plane_atomic_update(struct drm_plane *plane,
-				struct drm_atomic_state *state)
+static int zynqmp_disp_plane_mode_set(struct drm_plane *plane,
+				      struct drm_framebuffer *fb,
+				      int crtc_x, int crtc_y,
+				      unsigned int crtc_w, unsigned int crtc_h,
+				      u32 src_x, u32 src_y,
+				      u32 src_w, u32 src_h)
 {
-	struct drm_plane_state *old_state = drm_atomic_get_old_plane_state(state, plane);
-	struct drm_plane_state *new_state = drm_atomic_get_new_plane_state(state, plane);
 	struct zynqmp_disp_layer *layer = plane_to_layer(plane);
-	bool format_changed = false;
+	const struct drm_format_info *info = fb->format;
+	struct device *dev = layer->disp->dev;
+	dma_addr_t paddr;
+	unsigned int i;
+	int ret;
 
-	if (!old_state->fb ||
-	    old_state->fb->format->format != new_state->fb->format->format)
-		format_changed = true;
+	if (!info) {
+		dev_err(dev, "No format info found\n");
+		return -EINVAL;
+	}
 
-	/*
-	 * If the format has changed (including going from a previously
-	 * disabled state to any format), reconfigure the format. Disable the
-	 * plane first if needed.
-	 */
-	if (format_changed) {
-		if (old_state->fb)
-			zynqmp_disp_layer_disable(layer);
+	ret = zynqmp_disp_layer_check_size(layer->disp, layer, src_w, src_h);
+	if (ret)
+		return ret;
 
-		zynqmp_disp_layer_set_format(layer, new_state);
+	for (i = 0; i < info->num_planes; i++) {
+		unsigned int width = src_w / (i ? info->hsub : 1);
+		unsigned int height = src_h / (i ? info->vsub : 1);
+		int width_bytes;
+
+		paddr = drm_fb_cma_get_gem_addr(fb, plane->state, i);
+		if (!paddr) {
+			dev_err(dev, "failed to get a paddr\n");
+			return -EINVAL;
+		}
+
+		layer->dma[i].xt.numf = height;
+		width_bytes = drm_format_plane_width_bytes(info, i, width);
+		layer->dma[i].sgl[0].size = width_bytes;
+		layer->dma[i].sgl[0].icg = fb->pitches[i] -
+					   layer->dma[i].sgl[0].size;
+		layer->dma[i].xt.src_start = paddr;
+		layer->dma[i].xt.frame_size = 1;
+		layer->dma[i].xt.dir = DMA_MEM_TO_DEV;
+		layer->dma[i].xt.src_sgl = true;
+		layer->dma[i].xt.dst_sgl = false;
+		layer->dma[i].is_active = true;
 	}
 
-	zynqmp_disp_layer_update(layer, new_state);
+	for (; i < ZYNQMP_DISP_MAX_NUM_SUB_PLANES; i++)
+		layer->dma[i].is_active = false;
 
-	if (zynqmp_disp_layer_is_gfx(layer))
-		zynqmp_disp_blend_set_global_alpha(layer->disp, true,
-						   plane->state->alpha >> 8);
+	ret = zynqmp_disp_layer_set_fmt(layer->disp,  layer, info->format);
+	if (ret)
+		dev_err(dev, "failed to set dp_sub layer fmt\n");
 
-	/* Enable or re-enable the plane is the format has changed. */
-	if (format_changed)
-		zynqmp_disp_layer_enable(layer);
+	return ret;
 }
 
-static const struct drm_plane_helper_funcs zynqmp_disp_plane_helper_funcs = {
-	.atomic_check		= zynqmp_disp_plane_atomic_check,
-	.atomic_update		= zynqmp_disp_plane_atomic_update,
-	.atomic_disable		= zynqmp_disp_plane_atomic_disable,
-};
+static void zynqmp_disp_plane_destroy(struct drm_plane *plane)
+{
+	struct zynqmp_disp_layer *layer = plane_to_layer(plane);
 
-static const struct drm_plane_funcs zynqmp_disp_plane_funcs = {
-	.update_plane		= drm_atomic_helper_update_plane,
-	.disable_plane		= drm_atomic_helper_disable_plane,
-	.destroy		= drm_plane_cleanup,
-	.reset			= drm_atomic_helper_plane_reset,
-	.atomic_duplicate_state	= drm_atomic_helper_plane_duplicate_state,
-	.atomic_destroy_state	= drm_atomic_helper_plane_destroy_state,
-};
+	xlnx_bridge_unregister(&layer->bridge);
+	drm_plane_cleanup(plane);
+}
 
-static int zynqmp_disp_create_planes(struct zynqmp_disp *disp)
+static int
+zynqmp_disp_plane_atomic_set_property(struct drm_plane *plane,
+				      struct drm_plane_state *state,
+				      struct drm_property *property, u64 val)
 {
-	unsigned int i, j;
-	int ret;
+	struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+	struct zynqmp_disp *disp = layer->disp;
+	int ret = 0;
 
-	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
-		struct zynqmp_disp_layer *layer = &disp->layers[i];
-		enum drm_plane_type type;
-		u32 *drm_formats;
-
-		drm_formats = drmm_kcalloc(disp->drm, sizeof(*drm_formats),
-					   layer->info->num_formats,
-					   GFP_KERNEL);
-		if (!drm_formats)
-			return -ENOMEM;
-
-		for (j = 0; j < layer->info->num_formats; ++j)
-			drm_formats[j] = layer->info->formats[j].drm_fmt;
-
-		/* Graphics layer is primary, and video layer is overlay. */
-		type = zynqmp_disp_layer_is_video(layer)
-		     ? DRM_PLANE_TYPE_OVERLAY : DRM_PLANE_TYPE_PRIMARY;
-		ret = drm_universal_plane_init(disp->drm, &layer->plane, 0,
-					       &zynqmp_disp_plane_funcs,
-					       drm_formats,
-					       layer->info->num_formats,
-					       NULL, type, NULL);
-		if (ret)
-			return ret;
+	if (property == disp->g_alpha_prop)
+		zynqmp_disp_set_alpha(disp, val);
+	else if (property == disp->g_alpha_en_prop)
+		zynqmp_disp_set_g_alpha(disp, val);
+	else if (property == disp->tpg_prop)
+		ret = zynqmp_disp_layer_set_tpg(disp, layer, val);
+	else
+		return -EINVAL;
 
-		drm_plane_helper_add(&layer->plane,
-				     &zynqmp_disp_plane_helper_funcs);
+	return ret;
+}
+
+static int
+zynqmp_disp_plane_atomic_get_property(struct drm_plane *plane,
+				      const struct drm_plane_state *state,
+				      struct drm_property *property,
+				      uint64_t *val)
+{
+	struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+	struct zynqmp_disp *disp = layer->disp;
+	int ret = 0;
+
+	if (property == disp->g_alpha_prop)
+		*val = zynqmp_disp_get_alpha(disp);
+	else if (property == disp->g_alpha_en_prop)
+		*val = zynqmp_disp_get_g_alpha(disp);
+	else if (property == disp->tpg_prop)
+		*val = zynqmp_disp_layer_get_tpg(disp, layer);
+	else
+		return -EINVAL;
+
+	return ret;
+}
 
-		drm_plane_create_zpos_immutable_property(&layer->plane, i);
-		if (zynqmp_disp_layer_is_gfx(layer))
-			drm_plane_create_alpha_property(&layer->plane);
+static int
+zynqmp_disp_plane_atomic_update_plane(struct drm_plane *plane,
+				      struct drm_crtc *crtc,
+				      struct drm_framebuffer *fb,
+				      int crtc_x, int crtc_y,
+				      unsigned int crtc_w, unsigned int crtc_h,
+				      u32 src_x, u32 src_y,
+				      u32 src_w, u32 src_h,
+				      struct drm_modeset_acquire_ctx *ctx)
+{
+	struct drm_atomic_state *state;
+	struct drm_plane_state *plane_state;
+	int ret;
+
+	state = drm_atomic_state_alloc(plane->dev);
+	if (!state)
+		return -ENOMEM;
+
+	state->acquire_ctx = ctx;
+	plane_state = drm_atomic_get_plane_state(state, plane);
+	if (IS_ERR(plane_state)) {
+		ret = PTR_ERR(plane_state);
+		goto fail;
 	}
 
-	return 0;
+	ret = drm_atomic_set_crtc_for_plane(plane_state, crtc);
+	if (ret)
+		goto fail;
+	drm_atomic_set_fb_for_plane(plane_state, fb);
+	plane_state->crtc_x = crtc_x;
+	plane_state->crtc_y = crtc_y;
+	plane_state->crtc_w = crtc_w;
+	plane_state->crtc_h = crtc_h;
+	plane_state->src_x = src_x;
+	plane_state->src_y = src_y;
+	plane_state->src_w = src_w;
+	plane_state->src_h = src_h;
+
+	if (plane == crtc->cursor)
+		state->legacy_cursor_update = true;
+
+	/* Do async-update if possible */
+	state->async_update = !drm_atomic_helper_async_check(plane->dev, state);
+	ret = drm_atomic_commit(state);
+fail:
+	drm_atomic_state_put(state);
+	return ret;
 }
 
-/**
- * zynqmp_disp_layer_release_dma - Release DMA channels for a layer
- * @disp: Display controller
- * @layer: The layer
- *
- * Release the DMA channels associated with @layer.
- */
-static void zynqmp_disp_layer_release_dma(struct zynqmp_disp *disp,
-					  struct zynqmp_disp_layer *layer)
+static struct drm_plane_funcs zynqmp_disp_plane_funcs = {
+	.update_plane		= zynqmp_disp_plane_atomic_update_plane,
+	.disable_plane		= drm_atomic_helper_disable_plane,
+	.atomic_set_property	= zynqmp_disp_plane_atomic_set_property,
+	.atomic_get_property	= zynqmp_disp_plane_atomic_get_property,
+	.destroy		= zynqmp_disp_plane_destroy,
+	.reset			= drm_atomic_helper_plane_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_plane_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_plane_destroy_state,
+};
+
+static void
+zynqmp_disp_plane_atomic_update(struct drm_plane *plane,
+				struct drm_atomic_state *state)
 {
-	unsigned int i;
+	int ret;
+	struct drm_plane_state *old_state = drm_atomic_get_old_plane_state(state, plane);
 
-	if (!layer->info)
+	if (!plane->state->crtc || !plane->state->fb)
 		return;
 
-	for (i = 0; i < layer->info->num_channels; i++) {
-		struct zynqmp_disp_layer_dma *dma = &layer->dmas[i];
+	if (plane->state->fb == old_state->fb &&
+	    plane->state->crtc_x == old_state->crtc_x &&
+	    plane->state->crtc_y == old_state->crtc_y &&
+	    plane->state->crtc_w == old_state->crtc_w &&
+	    plane->state->crtc_h == old_state->crtc_h &&
+	    plane->state->src_x == old_state->src_x &&
+	    plane->state->src_y == old_state->src_y &&
+	    plane->state->src_w == old_state->src_w &&
+	    plane->state->src_h == old_state->src_h)
+		return;
 
-		if (!dma->chan)
-			continue;
+	if (old_state->fb &&
+	    old_state->fb->format->format != plane->state->fb->format->format)
+		zynqmp_disp_plane_disable(plane);
+
+	ret = zynqmp_disp_plane_mode_set(plane, plane->state->fb,
+					 plane->state->crtc_x,
+					 plane->state->crtc_y,
+					 plane->state->crtc_w,
+					 plane->state->crtc_h,
+					 plane->state->src_x >> 16,
+					 plane->state->src_y >> 16,
+					 plane->state->src_w >> 16,
+					 plane->state->src_h >> 16);
+	if (ret)
+		return;
 
-		/* Make sure the channel is terminated before release. */
-		dmaengine_terminate_sync(dma->chan);
-		dma_release_channel(dma->chan);
-	}
+	zynqmp_disp_plane_enable(plane);
 }
 
-/**
- * zynqmp_disp_destroy_layers - Destroy all layers
- * @disp: Display controller
- */
-static void zynqmp_disp_destroy_layers(struct zynqmp_disp *disp)
+static void
+zynqmp_disp_plane_atomic_disable(struct drm_plane *plane,
+				 struct drm_atomic_state *state)
 {
-	unsigned int i;
+	zynqmp_disp_plane_disable(plane);
+}
 
-	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
-		zynqmp_disp_layer_release_dma(disp, &disp->layers[i]);
+static int zynqmp_disp_plane_atomic_async_check(struct drm_plane *plane,
+						struct drm_atomic_state *state)
+{
+	return 0;
 }
 
-/**
- * zynqmp_disp_layer_request_dma - Request DMA channels for a layer
- * @disp: Display controller
- * @layer: The layer
- *
- * Request all DMA engine channels needed by @layer.
- *
- * Return: 0 on success, or the DMA channel request error otherwise
- */
-static int zynqmp_disp_layer_request_dma(struct zynqmp_disp *disp,
-					 struct zynqmp_disp_layer *layer)
+static void
+zynqmp_disp_plane_atomic_async_update(struct drm_plane *plane,
+				      struct drm_atomic_state *state)
 {
-	static const char * const dma_names[] = { "vid", "gfx" };
-	unsigned int i;
 	int ret;
+	struct drm_plane_state *new_state = drm_atomic_get_new_plane_state(state, plane);
 
-	for (i = 0; i < layer->info->num_channels; i++) {
-		struct zynqmp_disp_layer_dma *dma = &layer->dmas[i];
-		char dma_channel_name[16];
-
-		snprintf(dma_channel_name, sizeof(dma_channel_name),
-			 "%s%u", dma_names[layer->id], i);
-		dma->chan = dma_request_chan(disp->dev, dma_channel_name);
-		if (IS_ERR(dma->chan)) {
-			dev_err(disp->dev, "failed to request dma channel\n");
-			ret = PTR_ERR(dma->chan);
-			dma->chan = NULL;
-			return ret;
-		}
-	}
+	if (plane->state->fb == new_state->fb)
+		return;
 
-	return 0;
+	if (plane->state->fb &&
+	    plane->state->fb->format->format != new_state->fb->format->format)
+		zynqmp_disp_plane_disable(plane);
+
+	 /* Update the current state with new configurations */
+	swap(plane->state->fb, new_state->fb);
+	plane->state->crtc = new_state->crtc;
+	plane->state->crtc_x = new_state->crtc_x;
+	plane->state->crtc_y = new_state->crtc_y;
+	plane->state->crtc_w = new_state->crtc_w;
+	plane->state->crtc_h = new_state->crtc_h;
+	plane->state->src_x = new_state->src_x;
+	plane->state->src_y = new_state->src_y;
+	plane->state->src_w = new_state->src_w;
+	plane->state->src_h = new_state->src_h;
+	plane->state->state = new_state->state;
+
+	ret = zynqmp_disp_plane_mode_set(plane, plane->state->fb,
+					 plane->state->crtc_x,
+					 plane->state->crtc_y,
+					 plane->state->crtc_w,
+					 plane->state->crtc_h,
+					 plane->state->src_x >> 16,
+					 plane->state->src_y >> 16,
+					 plane->state->src_w >> 16,
+					 plane->state->src_h >> 16);
+	if (ret)
+		return;
+
+	zynqmp_disp_plane_enable(plane);
 }
 
-/**
- * zynqmp_disp_create_layers - Create and initialize all layers
- * @disp: Display controller
- *
- * Return: 0 on success, or the DMA channel request error otherwise
- */
-static int zynqmp_disp_create_layers(struct zynqmp_disp *disp)
-{
-	static const struct zynqmp_disp_layer_info layer_info[] = {
-		[ZYNQMP_DISP_LAYER_VID] = {
-			.formats = avbuf_vid_fmts,
-			.num_formats = ARRAY_SIZE(avbuf_vid_fmts),
-			.num_channels = 3,
-		},
-		[ZYNQMP_DISP_LAYER_GFX] = {
-			.formats = avbuf_gfx_fmts,
-			.num_formats = ARRAY_SIZE(avbuf_gfx_fmts),
-			.num_channels = 1,
-		},
-	};
+static const struct drm_plane_helper_funcs zynqmp_disp_plane_helper_funcs = {
+	.atomic_update		= zynqmp_disp_plane_atomic_update,
+	.atomic_disable		= zynqmp_disp_plane_atomic_disable,
+	.atomic_async_check	= zynqmp_disp_plane_atomic_async_check,
+	.atomic_async_update	= zynqmp_disp_plane_atomic_async_update,
+};
 
+static int zynqmp_disp_create_plane(struct zynqmp_disp *disp)
+{
+	struct zynqmp_disp_layer *layer;
 	unsigned int i;
+	u32 *fmts = NULL;
+	unsigned int num_fmts = 0;
+	enum drm_plane_type type;
 	int ret;
 
+	/* graphics layer is primary, and video layer is overaly */
+	type = DRM_PLANE_TYPE_OVERLAY;
 	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
-		struct zynqmp_disp_layer *layer = &disp->layers[i];
-
-		layer->id = i;
-		layer->disp = disp;
-		layer->info = &layer_info[i];
-
-		ret = zynqmp_disp_layer_request_dma(disp, layer);
+		layer = &disp->layers[i];
+		zynqmp_disp_layer_get_fmts(disp, layer, &fmts, &num_fmts);
+		ret = drm_universal_plane_init(disp->drm, &layer->plane, 0,
+					       &zynqmp_disp_plane_funcs, fmts,
+					       num_fmts, NULL, type, NULL);
 		if (ret)
-			goto err;
+			goto err_plane;
+		drm_plane_helper_add(&layer->plane,
+				     &zynqmp_disp_plane_helper_funcs);
+		type = DRM_PLANE_TYPE_PRIMARY;
 	}
 
-	return 0;
+	/* Attach properties to each layers */
+	drm_object_attach_property(&layer->plane.base, disp->g_alpha_prop,
+				   ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX);
+	disp->alpha = ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX;
+	/* Enable the global alpha as default */
+	drm_object_attach_property(&layer->plane.base, disp->g_alpha_en_prop,
+				   true);
+	disp->alpha_en = true;
+
+	layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+	drm_object_attach_property(&layer->plane.base, disp->tpg_prop, false);
 
-err:
-	zynqmp_disp_destroy_layers(disp);
+	return ret;
+
+err_plane:
+	if (i)
+		drm_plane_cleanup(&disp->layers[0].plane);
 	return ret;
 }
 
-/* -----------------------------------------------------------------------------
- * ZynqMP Display & DRM CRTC
- */
+static void zynqmp_disp_destroy_plane(struct zynqmp_disp *disp)
+{
+	unsigned int i;
 
-/**
- * zynqmp_disp_enable - Enable the display controller
- * @disp: Display controller
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
+		zynqmp_disp_plane_destroy(&disp->layers[i].plane);
+}
+
+/*
+ * Xlnx crtc functions
  */
-static void zynqmp_disp_enable(struct zynqmp_disp *disp)
+
+static inline struct zynqmp_disp *xlnx_crtc_to_disp(struct xlnx_crtc *xlnx_crtc)
+{
+	return container_of(xlnx_crtc, struct zynqmp_disp, xlnx_crtc);
+}
+
+static int zynqmp_disp_get_max_width(struct xlnx_crtc *xlnx_crtc)
 {
-	zynqmp_disp_avbuf_enable(disp);
-	/* Choose clock source based on the DT clock handle. */
-	zynqmp_disp_avbuf_set_clocks_sources(disp, disp->pclk_from_ps,
-					     disp->audio.clk_from_ps, true);
-	zynqmp_disp_avbuf_enable_channels(disp);
-	zynqmp_disp_avbuf_enable_audio(disp);
+	return ZYNQMP_DISP_MAX_WIDTH;
+}
 
-	zynqmp_disp_audio_enable(disp);
+static int zynqmp_disp_get_max_height(struct xlnx_crtc *xlnx_crtc)
+{
+	return ZYNQMP_DISP_MAX_HEIGHT;
 }
 
-/**
- * zynqmp_disp_disable - Disable the display controller
- * @disp: Display controller
- */
-static void zynqmp_disp_disable(struct zynqmp_disp *disp)
+static uint32_t zynqmp_disp_get_format(struct xlnx_crtc *xlnx_crtc)
+{
+	struct zynqmp_disp *disp = xlnx_crtc_to_disp(xlnx_crtc);
+
+	return disp->layers[ZYNQMP_DISP_LAYER_GFX].fmt->drm_fmt;
+}
+
+static unsigned int zynqmp_disp_get_align(struct xlnx_crtc *xlnx_crtc)
 {
-	zynqmp_disp_audio_disable(disp);
+	struct zynqmp_disp *disp = xlnx_crtc_to_disp(xlnx_crtc);
+	struct zynqmp_disp_layer *layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
 
-	zynqmp_disp_avbuf_disable_audio(disp);
-	zynqmp_disp_avbuf_disable_channels(disp);
-	zynqmp_disp_avbuf_disable(disp);
+	return 1 << layer->dma->chan->device->copy_align;
 }
 
+static u64 zynqmp_disp_get_dma_mask(struct xlnx_crtc *xlnx_crtc)
+{
+	return DMA_BIT_MASK(ZYNQMP_DISP_MAX_DMA_BIT);
+}
+
+/*
+ * DRM crtc functions
+ */
+
 static inline struct zynqmp_disp *crtc_to_disp(struct drm_crtc *crtc)
 {
-	return container_of(crtc, struct zynqmp_disp, crtc);
+	struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+
+	return xlnx_crtc_to_disp(xlnx_crtc);
 }
 
-static int zynqmp_disp_crtc_setup_clock(struct drm_crtc *crtc,
-					struct drm_display_mode *adjusted_mode)
+static int zynqmp_disp_crtc_mode_set(struct drm_crtc *crtc,
+				     struct drm_display_mode *mode,
+				     struct drm_display_mode *adjusted_mode,
+				     int x, int y,
+				     struct drm_framebuffer *old_fb)
 {
 	struct zynqmp_disp *disp = crtc_to_disp(crtc);
-	unsigned long mode_clock = adjusted_mode->clock * 1000;
 	unsigned long rate;
 	long diff;
 	int ret;
 
-	ret = clk_set_rate(disp->pclk, mode_clock);
+	zynqmp_disp_clk_disable(disp->pclk, &disp->pclk_en);
+	ret = clk_set_rate(disp->pclk,
+			   (unsigned long)adjusted_mode->clock * 1000);
 	if (ret) {
 		dev_err(disp->dev, "failed to set a pixel clock\n");
 		return ret;
 	}
 
 	rate = clk_get_rate(disp->pclk);
-	diff = rate - mode_clock;
-	if (abs(diff) > mode_clock / 20)
-		dev_info(disp->dev,
-			 "requested pixel rate: %lu actual rate: %lu\n",
-			 mode_clock, rate);
-	else
-		dev_dbg(disp->dev,
-			"requested pixel rate: %lu actual rate: %lu\n",
-			mode_clock, rate);
+	diff = rate - (unsigned long)adjusted_mode->clock * 1000;
+	if (abs(diff) > ((long)adjusted_mode->clock * 1000) / 20) {
+		dev_info(disp->dev, "request pixel rate: %d actual rate: %lu\n",
+			 adjusted_mode->clock, rate);
+	} else {
+		dev_dbg(disp->dev, "request pixel rate: %d actual rate: %lu\n",
+			adjusted_mode->clock, rate);
+	}
+
+	/* The timing register should be programmed always */
+	zynqmp_dp_encoder_mode_set_stream(disp->dpsub->dp, adjusted_mode);
 
 	return 0;
 }
@@ -1451,22 +2602,23 @@
 	struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode;
 	int ret, vrefresh;
 
-	pm_runtime_get_sync(disp->dev);
+	zynqmp_disp_crtc_mode_set(crtc, &crtc->state->mode,
+				  adjusted_mode, crtc->x, crtc->y, NULL);
 
-	zynqmp_disp_crtc_setup_clock(crtc, adjusted_mode);
+	ret = pm_runtime_get_sync(disp->dev);
+	if (ret < 0) {
+		dev_err(disp->dev, "IRQ sync failed to resume: %d\n", ret);
+		return;
+	}
 
-	ret = clk_prepare_enable(disp->pclk);
+	ret = zynqmp_disp_clk_enable(disp->pclk, &disp->pclk_en);
 	if (ret) {
 		dev_err(disp->dev, "failed to enable a pixel clock\n");
-		pm_runtime_put_sync(disp->dev);
 		return;
 	}
-
-	zynqmp_disp_blend_set_output_format(disp, ZYNQMP_DPSUB_FORMAT_RGB);
-	zynqmp_disp_blend_set_bg_color(disp, 0, 0, 0);
-
+	zynqmp_disp_set_output_fmt(disp, disp->color);
+	zynqmp_disp_set_bg_color(disp, disp->bg_c0, disp->bg_c1, disp->bg_c2);
 	zynqmp_disp_enable(disp);
-
 	/* Delay of 3 vblank intervals for timing gen to be stable */
 	vrefresh = (adjusted_mode->clock * 1000) /
 		   (adjusted_mode->vtotal * adjusted_mode->htotal);
@@ -1478,29 +2630,12 @@
 				struct drm_atomic_state *state)
 {
 	struct zynqmp_disp *disp = crtc_to_disp(crtc);
-	struct drm_plane_state *old_plane_state;
-
-	/*
-	 * Disable the plane if active. The old plane state can be NULL in the
-	 * .shutdown() path if the plane is already disabled, skip
-	 * zynqmp_disp_plane_atomic_disable() in that case.
-	 */
-	old_plane_state = drm_atomic_get_old_plane_state(state, crtc->primary);
-	if (old_plane_state)
-		zynqmp_disp_plane_atomic_disable(crtc->primary, state);
-
-	zynqmp_disp_disable(disp);
-
-	drm_crtc_vblank_off(&disp->crtc);
-
-	spin_lock_irq(&crtc->dev->event_lock);
-	if (crtc->state->event) {
-		drm_crtc_send_vblank_event(crtc, crtc->state->event);
-		crtc->state->event = NULL;
-	}
-	spin_unlock_irq(&crtc->dev->event_lock);
 
-	clk_disable_unprepare(disp->pclk);
+	zynqmp_disp_clk_disable(disp->pclk, &disp->pclk_en);
+	zynqmp_disp_plane_disable(crtc->primary);
+	zynqmp_disp_disable(disp, true);
+	if (!disp->dpsub->external_crtc_attached)
+		drm_crtc_vblank_off(crtc);
 	pm_runtime_put_sync(disp->dev);
 }
 
@@ -1515,37 +2650,31 @@
 			      struct drm_atomic_state *state)
 {
 	drm_crtc_vblank_on(crtc);
-}
-
-static void
-zynqmp_disp_crtc_atomic_flush(struct drm_crtc *crtc,
-			      struct drm_atomic_state *state)
-{
+	/* Don't rely on vblank when disabling crtc */
+	spin_lock_irq(&crtc->dev->event_lock);
 	if (crtc->state->event) {
-		struct drm_pending_vblank_event *event;
-
-		/* Consume the flip_done event from atomic helper. */
-		event = crtc->state->event;
-		crtc->state->event = NULL;
-
-		event->pipe = drm_crtc_index(crtc);
-
+		/* Consume the flip_done event from atomic helper */
+		crtc->state->event->pipe = drm_crtc_index(crtc);
 		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
-
-		spin_lock_irq(&crtc->dev->event_lock);
-		drm_crtc_arm_vblank_event(crtc, event);
-		spin_unlock_irq(&crtc->dev->event_lock);
+		drm_crtc_arm_vblank_event(crtc, crtc->state->event);
+		crtc->state->event = NULL;
 	}
+	spin_unlock_irq(&crtc->dev->event_lock);
 }
 
-static const struct drm_crtc_helper_funcs zynqmp_disp_crtc_helper_funcs = {
+static struct drm_crtc_helper_funcs zynqmp_disp_crtc_helper_funcs = {
 	.atomic_enable	= zynqmp_disp_crtc_atomic_enable,
 	.atomic_disable	= zynqmp_disp_crtc_atomic_disable,
 	.atomic_check	= zynqmp_disp_crtc_atomic_check,
 	.atomic_begin	= zynqmp_disp_crtc_atomic_begin,
-	.atomic_flush	= zynqmp_disp_crtc_atomic_flush,
 };
 
+static void zynqmp_disp_crtc_destroy(struct drm_crtc *crtc)
+{
+	zynqmp_disp_crtc_atomic_disable(crtc, NULL);
+	drm_crtc_cleanup(crtc);
+}
+
 static int zynqmp_disp_crtc_enable_vblank(struct drm_crtc *crtc)
 {
 	struct zynqmp_disp *disp = crtc_to_disp(crtc);
@@ -1562,10 +2691,60 @@
 	zynqmp_dp_disable_vblank(disp->dpsub->dp);
 }
 
-static const struct drm_crtc_funcs zynqmp_disp_crtc_funcs = {
-	.destroy		= drm_crtc_cleanup,
+static int
+zynqmp_disp_crtc_atomic_set_property(struct drm_crtc *crtc,
+				     struct drm_crtc_state *state,
+				     struct drm_property *property,
+				     uint64_t val)
+{
+	struct zynqmp_disp *disp = crtc_to_disp(crtc);
+
+	/*
+	 * CRTC prop values are just stored here and applied when CRTC gets
+	 * enabled
+	 */
+	if (property == disp->color_prop)
+		disp->color = val;
+	else if (property == disp->bg_c0_prop)
+		disp->bg_c0 = val;
+	else if (property == disp->bg_c1_prop)
+		disp->bg_c1 = val;
+	else if (property == disp->bg_c2_prop)
+		disp->bg_c2 = val;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static int
+zynqmp_disp_crtc_atomic_get_property(struct drm_crtc *crtc,
+				     const struct drm_crtc_state *state,
+				     struct drm_property *property,
+				     uint64_t *val)
+{
+	struct zynqmp_disp *disp = crtc_to_disp(crtc);
+
+	if (property == disp->color_prop)
+		*val = disp->color;
+	else if (property == disp->bg_c0_prop)
+		*val = disp->bg_c0;
+	else if (property == disp->bg_c1_prop)
+		*val = disp->bg_c1;
+	else if (property == disp->bg_c2_prop)
+		*val = disp->bg_c2;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static struct drm_crtc_funcs zynqmp_disp_crtc_funcs = {
+	.destroy		= zynqmp_disp_crtc_destroy,
 	.set_config		= drm_atomic_helper_set_config,
 	.page_flip		= drm_atomic_helper_page_flip,
+	.atomic_set_property	= zynqmp_disp_crtc_atomic_set_property,
+	.atomic_get_property	= zynqmp_disp_crtc_atomic_get_property,
 	.reset			= drm_atomic_helper_crtc_reset,
 	.atomic_duplicate_state	= drm_atomic_helper_crtc_duplicate_state,
 	.atomic_destroy_state	= drm_atomic_helper_crtc_destroy_state,
@@ -1576,117 +2755,472 @@
 static int zynqmp_disp_create_crtc(struct zynqmp_disp *disp)
 {
 	struct drm_plane *plane = &disp->layers[ZYNQMP_DISP_LAYER_GFX].plane;
+	struct drm_mode_object *obj = &disp->xlnx_crtc.crtc.base;
 	int ret;
 
-	ret = drm_crtc_init_with_planes(disp->drm, &disp->crtc, plane,
-					NULL, &zynqmp_disp_crtc_funcs, NULL);
-	if (ret < 0)
+	ret = drm_crtc_init_with_planes(disp->drm, &disp->xlnx_crtc.crtc,
+					plane, NULL, &zynqmp_disp_crtc_funcs,
+					NULL);
+	if (ret < 0) {
+		dev_err(disp->dev, "failed to initialize disp CRTC: %d\n",
+			ret);
 		return ret;
+	}
 
-	drm_crtc_helper_add(&disp->crtc, &zynqmp_disp_crtc_helper_funcs);
-
-	/* Start with vertical blanking interrupt reporting disabled. */
-	drm_crtc_vblank_off(&disp->crtc);
+	drm_crtc_helper_add(&disp->xlnx_crtc.crtc,
+			    &zynqmp_disp_crtc_helper_funcs);
+	drm_object_attach_property(obj, disp->color_prop, 0);
+	zynqmp_dp_set_color(disp->dpsub->dp, zynqmp_disp_color_enum[0].name);
+	drm_object_attach_property(obj, disp->bg_c0_prop, 0);
+	drm_object_attach_property(obj, disp->bg_c1_prop, 0);
+	drm_object_attach_property(obj, disp->bg_c2_prop, 0);
+
+	disp->xlnx_crtc.get_max_width = &zynqmp_disp_get_max_width;
+	disp->xlnx_crtc.get_max_height = &zynqmp_disp_get_max_height;
+	disp->xlnx_crtc.get_format = &zynqmp_disp_get_format;
+	disp->xlnx_crtc.get_align = &zynqmp_disp_get_align;
+	disp->xlnx_crtc.get_dma_mask = &zynqmp_disp_get_dma_mask;
+	/* Only register the PS DP CRTC if there is no external port/CRTC */
+	if (!disp->dpsub->external_crtc_attached)
+		xlnx_crtc_register(disp->drm, &disp->xlnx_crtc);
 
 	return 0;
 }
 
+static void zynqmp_disp_destroy_crtc(struct zynqmp_disp *disp)
+{
+	if (!disp->dpsub->external_crtc_attached)
+		xlnx_crtc_unregister(disp->drm, &disp->xlnx_crtc);
+	zynqmp_disp_crtc_destroy(&disp->xlnx_crtc.crtc);
+}
+
 static void zynqmp_disp_map_crtc_to_plane(struct zynqmp_disp *disp)
 {
-	u32 possible_crtcs = drm_crtc_mask(&disp->crtc);
+	u32 possible_crtcs = drm_crtc_mask(&disp->xlnx_crtc.crtc);
 	unsigned int i;
 
 	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
 		disp->layers[i].plane.possible_crtcs = possible_crtcs;
 }
 
-/* -----------------------------------------------------------------------------
- * Initialization & Cleanup
+/*
+ * Xlnx bridge functions
  */
 
-int zynqmp_disp_drm_init(struct zynqmp_dpsub *dpsub)
+static inline struct zynqmp_disp_layer
+*bridge_to_layer(struct xlnx_bridge *bridge)
 {
-	struct zynqmp_disp *disp = dpsub->disp;
+	return container_of(bridge, struct zynqmp_disp_layer, bridge);
+}
+
+static int zynqmp_disp_bridge_enable(struct xlnx_bridge *bridge)
+{
+	struct zynqmp_disp_layer *layer = bridge_to_layer(bridge);
+	struct zynqmp_disp *disp = layer->disp;
+	struct drm_crtc *crtc = &disp->xlnx_crtc.crtc;
+	struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode;
+	struct videomode vm;
 	int ret;
 
-	ret = zynqmp_disp_create_planes(disp);
+	if (!disp->_pl_pclk) {
+		dev_err(disp->dev, "PL clock is required for live\n");
+		return -ENODEV;
+	}
+
+	ret = zynqmp_disp_layer_check_size(disp, layer, layer->w, layer->h);
 	if (ret)
 		return ret;
 
-	ret = zynqmp_disp_create_crtc(disp);
-	if (ret < 0)
+	/* Enable DP encoder if external CRTC attached */
+	if (disp->dpsub->external_crtc_attached)
+		zynqmp_disp_crtc_atomic_enable(crtc, NULL);
+
+	if (disp->vtc_bridge) {
+		drm_display_mode_to_videomode(adjusted_mode, &vm);
+		xlnx_bridge_set_timing(disp->vtc_bridge, &vm);
+		xlnx_bridge_enable(disp->vtc_bridge);
+	}
+
+	/* If external CRTC is connected through video layer, set alpha to 0 */
+	if (disp->dpsub->external_crtc_attached && layer->id == ZYNQMP_DISP_LAYER_VID)
+		disp->alpha = 0;
+
+	zynqmp_disp_set_g_alpha(disp, disp->alpha_en);
+	zynqmp_disp_set_alpha(disp, disp->alpha);
+	ret = zynqmp_disp_layer_enable(layer->disp, layer,
+				       ZYNQMP_DISP_LAYER_LIVE);
+	if (ret)
+		return ret;
+
+	if (layer->id == ZYNQMP_DISP_LAYER_GFX && disp->tpg_on) {
+		layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+		zynqmp_disp_layer_set_tpg(disp, layer, disp->tpg_on);
+	}
+
+	if (zynqmp_disp_av_buf_vid_timing_src_is_int(&disp->av_buf) ||
+	    zynqmp_disp_av_buf_vid_clock_src_is_ps(&disp->av_buf)) {
+		dev_info(disp->dev,
+			 "Disabling the pipeline to change the clk/timing src");
+		zynqmp_disp_disable(disp, true);
+		zynqmp_disp_av_buf_set_vid_clock_src(&disp->av_buf, false);
+		zynqmp_disp_av_buf_set_vid_timing_src(&disp->av_buf, false);
+	}
+
+	zynqmp_disp_enable(disp);
+
+	return 0;
+}
+
+static void zynqmp_disp_bridge_disable(struct xlnx_bridge *bridge)
+{
+	struct zynqmp_disp_layer *layer = bridge_to_layer(bridge);
+	struct zynqmp_disp *disp = layer->disp;
+
+	zynqmp_disp_disable(disp, false);
+
+	zynqmp_disp_layer_disable(disp, layer, ZYNQMP_DISP_LAYER_LIVE);
+	if (layer->id == ZYNQMP_DISP_LAYER_VID && disp->tpg_on)
+		zynqmp_disp_layer_set_tpg(disp, layer, disp->tpg_on);
+
+	if (!zynqmp_disp_layer_is_live(disp)) {
+		dev_info(disp->dev,
+			 "Disabling the pipeline to change the clk/timing src");
+		zynqmp_disp_disable(disp, true);
+		zynqmp_disp_av_buf_set_vid_clock_src(&disp->av_buf, true);
+		zynqmp_disp_av_buf_set_vid_timing_src(&disp->av_buf, true);
+		if (zynqmp_disp_layer_is_enabled(disp))
+			zynqmp_disp_enable(disp);
+	}
+}
+
+static int zynqmp_disp_bridge_set_input(struct xlnx_bridge *bridge,
+					u32 width, u32 height, u32 bus_fmt)
+{
+	struct zynqmp_disp_layer *layer = bridge_to_layer(bridge);
+	int ret;
+
+	ret = zynqmp_disp_layer_check_size(layer->disp, layer, width, height);
+	if (ret)
 		return ret;
 
+	ret = zynqmp_disp_layer_set_live_fmt(layer->disp,  layer, bus_fmt);
+	if (ret)
+		dev_err(layer->disp->dev, "failed to set live fmt\n");
+
+	return ret;
+}
+
+static int zynqmp_disp_bridge_get_input_fmts(struct xlnx_bridge *bridge,
+					     const u32 **fmts, u32 *count)
+{
+	struct zynqmp_disp_layer *layer = bridge_to_layer(bridge);
+
+	*fmts = layer->bus_fmts;
+	*count = layer->num_bus_fmts;
+
+	return 0;
+}
+
+static int zynqmp_disp_bridge_set_timing(struct xlnx_bridge *bridge,
+					 struct videomode *vm)
+{
+	struct zynqmp_disp_layer *layer = bridge_to_layer(bridge);
+	struct zynqmp_disp *disp = layer->disp;
+	struct drm_crtc *crtc = &disp->xlnx_crtc.crtc;
+	struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode;
+
+	drm_display_mode_from_videomode(vm, adjusted_mode);
+
+	return 0;
+}
+
+/*
+ * Component functions
+ */
+
+int zynqmp_disp_bind(struct device *dev, struct device *master, void *data)
+{
+	struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+	struct zynqmp_disp *disp = dpsub->disp;
+	struct drm_device *drm = data;
+	int num;
+	u64 max;
+	int ret;
+
+	disp->drm = drm;
+
+	max = ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX;
+	disp->g_alpha_prop = drm_property_create_range(drm, 0, "alpha", 0, max);
+	disp->g_alpha_en_prop = drm_property_create_bool(drm, 0,
+							 "g_alpha_en");
+	num = ARRAY_SIZE(zynqmp_disp_color_enum);
+	disp->color_prop = drm_property_create_enum(drm, 0,
+						    "output_color",
+						    zynqmp_disp_color_enum,
+						    num);
+	max = ZYNQMP_DISP_V_BLEND_BG_MAX;
+	disp->bg_c0_prop = drm_property_create_range(drm, 0, "bg_c0", 0, max);
+	disp->bg_c1_prop = drm_property_create_range(drm, 0, "bg_c1", 0, max);
+	disp->bg_c2_prop = drm_property_create_range(drm, 0, "bg_c2", 0, max);
+	disp->tpg_prop = drm_property_create_bool(drm, 0, "tpg");
+
+	ret = zynqmp_disp_create_plane(disp);
+	if (ret)
+		return ret;
+	ret = zynqmp_disp_create_crtc(disp);
+	if (ret)
+		return ret;
 	zynqmp_disp_map_crtc_to_plane(disp);
 
 	return 0;
 }
 
-int zynqmp_disp_probe(struct zynqmp_dpsub *dpsub, struct drm_device *drm)
+void zynqmp_disp_unbind(struct device *dev, struct device *master, void *data)
+{
+	struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+	struct zynqmp_disp *disp = dpsub->disp;
+
+	zynqmp_disp_destroy_crtc(disp);
+	zynqmp_disp_destroy_plane(disp);
+	drm_property_destroy(disp->drm, disp->bg_c2_prop);
+	drm_property_destroy(disp->drm, disp->bg_c1_prop);
+	drm_property_destroy(disp->drm, disp->bg_c0_prop);
+	drm_property_destroy(disp->drm, disp->color_prop);
+	drm_property_destroy(disp->drm, disp->g_alpha_en_prop);
+	drm_property_destroy(disp->drm, disp->g_alpha_prop);
+}
+
+/*
+ * Platform initialization functions
+ */
+
+static int zynqmp_disp_enumerate_fmts(struct zynqmp_disp *disp)
 {
-	struct platform_device *pdev = to_platform_device(dpsub->dev);
-	struct zynqmp_disp *disp;
 	struct zynqmp_disp_layer *layer;
+	u32 *bus_fmts;
+	u32 i, size, num_bus_fmts;
+	u32 gfx_fmt = ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB565;
+
+	num_bus_fmts = ARRAY_SIZE(av_buf_live_fmts);
+	bus_fmts = devm_kzalloc(disp->dev, sizeof(*bus_fmts) * num_bus_fmts,
+				GFP_KERNEL);
+	if (!bus_fmts)
+		return -ENOMEM;
+	for (i = 0; i < num_bus_fmts; i++)
+		bus_fmts[i] = av_buf_live_fmts[i].bus_fmt;
+
+	layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+	layer->num_bus_fmts = num_bus_fmts;
+	layer->bus_fmts = bus_fmts;
+	size = ARRAY_SIZE(av_buf_vid_fmts);
+	layer->num_fmts = size;
+	layer->drm_fmts = devm_kzalloc(disp->dev,
+				       sizeof(*layer->drm_fmts) * size,
+				       GFP_KERNEL);
+	if (!layer->drm_fmts)
+		return -ENOMEM;
+	for (i = 0; i < layer->num_fmts; i++)
+		layer->drm_fmts[i] = av_buf_vid_fmts[i].drm_fmt;
+	layer->fmt = &av_buf_vid_fmts[ZYNQMP_DISP_AV_BUF_VID_FMT_YUYV];
+
+	layer = &disp->layers[ZYNQMP_DISP_LAYER_GFX];
+	layer->num_bus_fmts = num_bus_fmts;
+	layer->bus_fmts = bus_fmts;
+	size = ARRAY_SIZE(av_buf_gfx_fmts);
+	layer->num_fmts = size;
+	layer->drm_fmts = devm_kzalloc(disp->dev,
+				       sizeof(*layer->drm_fmts) * size,
+				       GFP_KERNEL);
+	if (!layer->drm_fmts)
+		return -ENOMEM;
+
+	for (i = 0; i < layer->num_fmts; i++)
+		layer->drm_fmts[i] = av_buf_gfx_fmts[i].drm_fmt;
+	if (zynqmp_disp_gfx_init_fmt < ARRAY_SIZE(zynqmp_disp_gfx_init_fmts))
+		gfx_fmt = zynqmp_disp_gfx_init_fmts[zynqmp_disp_gfx_init_fmt];
+	layer->fmt = &av_buf_gfx_fmts[gfx_fmt];
+
+	return 0;
+}
+
+int zynqmp_disp_probe(struct platform_device *pdev)
+{
+	struct zynqmp_dpsub *dpsub;
+	struct zynqmp_disp *disp;
 	struct resource *res;
+	void __iomem *regs;
 	int ret;
+	struct zynqmp_disp_layer *layer;
+	unsigned int i, j;
+	struct device_node *vtc_node;
 
-	disp = drmm_kzalloc(drm, sizeof(*disp), GFP_KERNEL);
+	disp = devm_kzalloc(&pdev->dev, sizeof(*disp), GFP_KERNEL);
 	if (!disp)
 		return -ENOMEM;
-
 	disp->dev = &pdev->dev;
-	disp->dpsub = dpsub;
-	disp->drm = drm;
-
-	dpsub->disp = disp;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "blend");
-	disp->blend.base = devm_ioremap_resource(disp->dev, res);
+	disp->blend.base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(disp->blend.base))
 		return PTR_ERR(disp->blend.base);
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "av_buf");
-	disp->avbuf.base = devm_ioremap_resource(disp->dev, res);
-	if (IS_ERR(disp->avbuf.base))
-		return PTR_ERR(disp->avbuf.base);
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "aud");
-	disp->audio.base = devm_ioremap_resource(disp->dev, res);
-	if (IS_ERR(disp->audio.base))
-		return PTR_ERR(disp->audio.base);
+	disp->av_buf.base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(disp->av_buf.base))
+		return PTR_ERR(disp->av_buf.base);
+
+	disp->aud.base = syscon_regmap_lookup_by_phandle(disp->dev->of_node,
+							 "xlnx,dpaud-reg");
+	if (IS_ERR(disp->aud.base)) {
+		dev_info(&pdev->dev, "could not find xlnx,dpaud-reg, trying direct register access. DisplayPort audio will not work\n");
+
+		regs = devm_platform_ioremap_resource_byname(pdev, "aud");
+		if (IS_ERR(regs)) {
+			dev_err(&pdev->dev, "get aud memory resource failed.\n");
+			return PTR_ERR(regs);
+		}
+		disp->aud.base =
+			devm_regmap_init_mmio(&pdev->dev, regs,
+					      &dpaud_regmap_config);
+		if (IS_ERR(disp->aud.base)) {
+			dev_err(&pdev->dev, "failed to init regmap\n");
+			return PTR_ERR(disp->aud.base);
+		}
+	}
+
+	dpsub = platform_get_drvdata(pdev);
+	dpsub->disp = disp;
+	disp->dpsub = dpsub;
+
+	ret = zynqmp_disp_enumerate_fmts(disp);
+	if (ret)
+		return ret;
 
 	/* Try the live PL video clock */
-	disp->pclk = devm_clk_get(disp->dev, "dp_live_video_in_clk");
-	if (!IS_ERR(disp->pclk))
-		disp->pclk_from_ps = false;
-	else if (PTR_ERR(disp->pclk) == -EPROBE_DEFER)
-		return PTR_ERR(disp->pclk);
+	disp->_pl_pclk = devm_clk_get(disp->dev, "dp_live_video_in_clk");
+	if (!IS_ERR(disp->_pl_pclk)) {
+		disp->pclk = disp->_pl_pclk;
+		ret = zynqmp_disp_clk_enable_disable(disp->pclk,
+						     &disp->pclk_en);
+		if (ret)
+			disp->pclk = NULL;
+	} else if (PTR_ERR(disp->_pl_pclk) == -EPROBE_DEFER) {
+		return PTR_ERR(disp->_pl_pclk);
+	}
 
 	/* If the live PL video clock is not valid, fall back to PS clock */
-	if (IS_ERR_OR_NULL(disp->pclk)) {
-		disp->pclk = devm_clk_get(disp->dev, "dp_vtc_pixel_clk_in");
-		if (IS_ERR(disp->pclk)) {
+	if (!disp->pclk) {
+		disp->_ps_pclk = devm_clk_get(disp->dev, "dp_vtc_pixel_clk_in");
+		if (IS_ERR(disp->_ps_pclk)) {
 			dev_err(disp->dev, "failed to init any video clock\n");
-			return PTR_ERR(disp->pclk);
+			return PTR_ERR(disp->_ps_pclk);
+		}
+		disp->pclk = disp->_ps_pclk;
+		ret = zynqmp_disp_clk_enable_disable(disp->pclk,
+						     &disp->pclk_en);
+		if (ret) {
+			dev_err(disp->dev, "failed to init any video clock\n");
+			return ret;
 		}
-		disp->pclk_from_ps = true;
 	}
 
-	zynqmp_disp_audio_init(disp);
+	disp->aclk = devm_clk_get(disp->dev, "dp_apb_clk");
+	if (IS_ERR(disp->aclk))
+		return PTR_ERR(disp->aclk);
+	ret = zynqmp_disp_clk_enable(disp->aclk, &disp->aclk_en);
+	if (ret) {
+		dev_err(disp->dev, "failed to enable the APB clk\n");
+		return ret;
+	}
+
+	/* Try the live PL audio clock */
+	disp->_pl_audclk = devm_clk_get(disp->dev, "dp_live_audio_aclk");
+	if (!IS_ERR(disp->_pl_audclk)) {
+		disp->audclk = disp->_pl_audclk;
+		ret = zynqmp_disp_clk_enable_disable(disp->audclk,
+						     &disp->audclk_en);
+		if (ret)
+			disp->audclk = NULL;
+	}
+
+	/* If the live PL audio clock is not valid, fall back to PS clock */
+	if (!disp->audclk) {
+		disp->_ps_audclk = devm_clk_get(disp->dev, "dp_aud_clk");
+		if (!IS_ERR(disp->_ps_audclk)) {
+			disp->audclk = disp->_ps_audclk;
+			ret = zynqmp_disp_clk_enable_disable(disp->audclk,
+							     &disp->audclk_en);
+			if (ret)
+				disp->audclk = NULL;
+		}
+
+		if (!disp->audclk) {
+			dev_err(disp->dev,
+				"audio is disabled due to clock failure\n");
+		}
+	}
 
-	ret = zynqmp_disp_create_layers(disp);
+	/* VTC Bridge support */
+	vtc_node = of_parse_phandle(disp->dev->of_node, "xlnx,bridge", 0);
+	if (vtc_node) {
+		disp->vtc_bridge = of_xlnx_bridge_get(vtc_node);
+		if (!disp->vtc_bridge) {
+			dev_info(disp->dev, "Didn't get vtc bridge instance\n");
+			return -EPROBE_DEFER;
+		}
+	} else {
+		dev_info(disp->dev, "vtc bridge property not present\n");
+	}
+
+	ret = zynqmp_disp_layer_create(disp);
 	if (ret)
-		return ret;
+		goto error_aclk;
 
-	layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
-	dpsub->dma_align = 1 << layer->dmas[0].chan->device->copy_align;
+	zynqmp_disp_init(disp);
+
+	/*
+	 * Register live bridges so external CRTCs will be able probe
+	 * successfully
+	 */
+	for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+		layer = &disp->layers[i];
+		layer->bridge.enable = &zynqmp_disp_bridge_enable;
+		layer->bridge.disable = &zynqmp_disp_bridge_disable;
+		layer->bridge.set_input = &zynqmp_disp_bridge_set_input;
+		layer->bridge.get_input_fmts =
+			&zynqmp_disp_bridge_get_input_fmts;
+		layer->bridge.set_timing = &zynqmp_disp_bridge_set_timing;
+		layer->bridge.of_node = disp->dev->of_node;
+		layer->bridge.extra_name = ((i == 0) ? ".vid" : ".gfx");
+		ret = xlnx_bridge_register(&layer->bridge);
+		if (ret) {
+			dev_info(disp->dev, "Bridge registration failed\n");
+			for (j = 0; j < i; j++)
+				xlnx_bridge_unregister(&disp->layers[j].bridge);
+			goto error_aclk;
+		}
+	}
 
 	return 0;
+
+error_aclk:
+	zynqmp_disp_clk_disable(disp->aclk, &disp->aclk_en);
+	return ret;
 }
 
-void zynqmp_disp_remove(struct zynqmp_dpsub *dpsub)
+int zynqmp_disp_remove(struct platform_device *pdev)
 {
+	struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
 	struct zynqmp_disp *disp = dpsub->disp;
 
-	zynqmp_disp_destroy_layers(disp);
+	zynqmp_disp_layer_destroy(disp);
+	if (disp->audclk)
+		zynqmp_disp_clk_disable(disp->audclk, &disp->audclk_en);
+	if (disp->vtc_bridge)
+		of_xlnx_bridge_put(disp->vtc_bridge);
+	zynqmp_disp_clk_disable(disp->aclk, &disp->aclk_en);
+	zynqmp_disp_clk_disable(disp->pclk, &disp->pclk_en);
+	dpsub->disp = NULL;
+
+	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_disp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_disp.h
@@ -12,31 +12,18 @@
 #ifndef _ZYNQMP_DISP_H_
 #define _ZYNQMP_DISP_H_
 
-#include <linux/types.h>
-
-/*
- * 3840x2160 is advertised as the maximum resolution, but almost any
- * resolutions under a 300Mhz pixel rate would work. Pick 4096x4096.
- */
-#define ZYNQMP_DISP_MAX_WIDTH				4096
-#define ZYNQMP_DISP_MAX_HEIGHT				4096
-
-/* The DPDMA is limited to 44 bit addressing. */
-#define ZYNQMP_DISP_MAX_DMA_BIT				44
-
-struct device;
-struct drm_device;
-struct platform_device;
 struct zynqmp_disp;
-struct zynqmp_dpsub;
 
 void zynqmp_disp_handle_vblank(struct zynqmp_disp *disp);
-bool zynqmp_disp_audio_enabled(struct zynqmp_disp *disp);
-unsigned int zynqmp_disp_get_audio_clk_rate(struct zynqmp_disp *disp);
+unsigned int zynqmp_disp_get_apb_clk_rate(struct zynqmp_disp *disp);
+bool zynqmp_disp_aud_enabled(struct zynqmp_disp *disp);
+unsigned int zynqmp_disp_get_aud_clk_rate(struct zynqmp_disp *disp);
 uint32_t zynqmp_disp_get_crtc_mask(struct zynqmp_disp *disp);
 
-int zynqmp_disp_drm_init(struct zynqmp_dpsub *dpsub);
-int zynqmp_disp_probe(struct zynqmp_dpsub *dpsub, struct drm_device *drm);
-void zynqmp_disp_remove(struct zynqmp_dpsub *dpsub);
+int zynqmp_disp_bind(struct device *dev, struct device *master, void *data);
+void zynqmp_disp_unbind(struct device *dev, struct device *master, void *data);
+
+int zynqmp_disp_probe(struct platform_device *pdev);
+int zynqmp_disp_remove(struct platform_device *pdev);
 
 #endif /* _ZYNQMP_DISP_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_disp_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_disp_regs.h
@@ -20,6 +20,8 @@
 #define ZYNQMP_DISP_V_BLEND_BG_CLR_2			0x8
 #define ZYNQMP_DISP_V_BLEND_BG_MAX			0xfff
 #define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA		0xc
+#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MASK	0x1fe
+#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX	0xff
 #define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_VALUE(n)	((n) << 1)
 #define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_EN		BIT(0)
 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT		0x14
@@ -28,12 +30,31 @@
 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR422	0x2
 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YONLY	0x3
 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_XVYCC	0x4
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_EN_DOWNSAMPLE	BIT(4)
 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_EN_DOWNSAMPLE	BIT(4)
-#define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL(n)		(0x18 + ((n) * 4))
+#define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL		0x18
 #define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_EN_US		BIT(0)
 #define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_RGB		BIT(1)
 #define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_BYPASS	BIT(8)
 #define ZYNQMP_DISP_V_BLEND_NUM_COEFF			9
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF0		0x20
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF1		0x24
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF2		0x28
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF3		0x2c
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF4		0x30
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF5		0x34
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF6		0x38
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF7		0x3c
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF8		0x40
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF0		0x44
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF1		0x48
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF2		0x4c
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF3		0x50
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF4		0x54
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF5		0x58
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF6		0x5c
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF7		0x60
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF8		0x64
 #define ZYNQMP_DISP_V_BLEND_NUM_OFFSET			3
 #define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF(n)		(0x20 + ((n) * 4))
 #define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF(n)		(0x44 + ((n) * 4))
@@ -41,6 +62,24 @@
 #define ZYNQMP_DISP_V_BLEND_OUTCSC_OFFSET(n)		(0x74 + ((n) * 4))
 #define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF(n)		(0x80 + ((n) * 4))
 #define ZYNQMP_DISP_V_BLEND_IN2CSC_OFFSET(n)		(0xa4 + ((n) * 4))
+#define ZYNQMP_DISP_V_BLEND_LUMA_IN1CSC_OFFSET		0x68
+#define ZYNQMP_DISP_V_BLEND_CR_IN1CSC_OFFSET		0x6c
+#define ZYNQMP_DISP_V_BLEND_CB_IN1CSC_OFFSET		0x70
+#define ZYNQMP_DISP_V_BLEND_LUMA_OUTCSC_OFFSET		0x74
+#define ZYNQMP_DISP_V_BLEND_CR_OUTCSC_OFFSET		0x78
+#define ZYNQMP_DISP_V_BLEND_CB_OUTCSC_OFFSET		0x7c
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF0		0x80
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF1		0x84
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF2		0x88
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF3		0x8c
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF4		0x90
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF5		0x94
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF6		0x98
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF7		0x9c
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF8		0xa0
+#define ZYNQMP_DISP_V_BLEND_LUMA_IN2CSC_OFFSET		0xa4
+#define ZYNQMP_DISP_V_BLEND_CR_IN2CSC_OFFSET		0xa8
+#define ZYNQMP_DISP_V_BLEND_CB_IN2CSC_OFFSET		0xac
 #define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_ENABLE		0x1d0
 #define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_COMP1		0x1d4
 #define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_COMP2		0x1d8
@@ -89,7 +128,7 @@
 #define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_2BPP		(9 << 8)
 #define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_1BPP		(10 << 8)
 #define ZYNQMP_DISP_AV_BUF_NON_LIVE_LATENCY		0x8
-#define ZYNQMP_DISP_AV_BUF_CHBUF(n)			(0x10 + ((n) * 4))
+#define ZYNQMP_DISP_AV_BUF_CHBUF			0x10
 #define ZYNQMP_DISP_AV_BUF_CHBUF_EN			BIT(0)
 #define ZYNQMP_DISP_AV_BUF_CHBUF_FLUSH			BIT(1)
 #define ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT	2
@@ -148,10 +187,22 @@
 #define ZYNQMP_DISP_AV_BUF_SRST_REG_VID_RST		BIT(1)
 #define ZYNQMP_DISP_AV_BUF_AUDIO_CH_CONFIG		0x12c
 #define ZYNQMP_DISP_AV_BUF_GFX_COMP_SF(n)		(0x200 + ((n) * 4))
+#define ZYNQMP_DISP_AV_BUF_GFX_COMP0_SF			0x200
+#define ZYNQMP_DISP_AV_BUF_GFX_COMP1_SF			0x204
+#define ZYNQMP_DISP_AV_BUF_GFX_COMP2_SF			0x208
 #define ZYNQMP_DISP_AV_BUF_VID_COMP_SF(n)		(0x20c + ((n) * 4))
+#define ZYNQMP_DISP_AV_BUF_VID_COMP0_SF			0x20c
+#define ZYNQMP_DISP_AV_BUF_VID_COMP1_SF			0x210
+#define ZYNQMP_DISP_AV_BUF_VID_COMP2_SF			0x214
 #define ZYNQMP_DISP_AV_BUF_LIVD_VID_COMP_SF(n)		(0x218 + ((n) * 4))
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP0_SF		0x218
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP1_SF		0x21c
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP2_SF		0x220
 #define ZYNQMP_DISP_AV_BUF_LIVE_VID_CONFIG		0x224
 #define ZYNQMP_DISP_AV_BUF_LIVD_GFX_COMP_SF(n)		(0x228 + ((n) * 4))
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP0_SF		0x228
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP1_SF		0x22c
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP2_SF		0x230
 #define ZYNQMP_DISP_AV_BUF_LIVE_GFX_CONFIG		0x234
 #define ZYNQMP_DISP_AV_BUF_4BIT_SF			0x11111
 #define ZYNQMP_DISP_AV_BUF_5BIT_SF			0x10842
@@ -165,10 +216,10 @@
 #define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_10		0x2
 #define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_12		0x3
 #define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_MASK		GENMASK(2, 0)
-#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB		0x0
-#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV444	0x1
-#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422	0x2
-#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YONLY	0x3
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB		0x00
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV444	0x10
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422	0x20
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YONLY	0x30
 #define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_MASK		GENMASK(5, 4)
 #define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_CB_FIRST		BIT(8)
 #define ZYNQMP_DISP_AV_BUF_PALETTE_MEMORY		0x400
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_dp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_dp.c
@@ -12,24 +12,20 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_connector.h>
 #include <drm/drm_crtc.h>
-#include <drm/drm_device.h>
+#include <drm/drm_crtc_helper.h>
 #include <drm/drm_dp_helper.h>
-#include <drm/drm_edid.h>
-#include <drm/drm_encoder.h>
-#include <drm/drm_managed.h>
-#include <drm/drm_modes.h>
 #include <drm/drm_of.h>
 #include <drm/drm_probe_helper.h>
-#include <drm/drm_simple_kms_helper.h>
 
-#include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/module.h>
+#include <linux/mutex.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/phy/phy.h>
 #include <linux/reset.h>
+#include <linux/uaccess.h>
 
 #include "zynqmp_disp.h"
 #include "zynqmp_dp.h"
@@ -47,188 +43,207 @@
 MODULE_PARM_DESC(power_on_delay_ms, "DP power on delay in msec (default: 4)");
 
 /* Link configuration registers */
-#define ZYNQMP_DP_LINK_BW_SET				0x0
-#define ZYNQMP_DP_LANE_COUNT_SET			0x4
-#define ZYNQMP_DP_ENHANCED_FRAME_EN			0x8
-#define ZYNQMP_DP_TRAINING_PATTERN_SET			0xc
-#define ZYNQMP_DP_SCRAMBLING_DISABLE			0x14
-#define ZYNQMP_DP_DOWNSPREAD_CTL			0x18
-#define ZYNQMP_DP_SOFTWARE_RESET			0x1c
-#define ZYNQMP_DP_SOFTWARE_RESET_STREAM1		BIT(0)
-#define ZYNQMP_DP_SOFTWARE_RESET_STREAM2		BIT(1)
-#define ZYNQMP_DP_SOFTWARE_RESET_STREAM3		BIT(2)
-#define ZYNQMP_DP_SOFTWARE_RESET_STREAM4		BIT(3)
-#define ZYNQMP_DP_SOFTWARE_RESET_AUX			BIT(7)
-#define ZYNQMP_DP_SOFTWARE_RESET_ALL			(ZYNQMP_DP_SOFTWARE_RESET_STREAM1 | \
-							 ZYNQMP_DP_SOFTWARE_RESET_STREAM2 | \
-							 ZYNQMP_DP_SOFTWARE_RESET_STREAM3 | \
-							 ZYNQMP_DP_SOFTWARE_RESET_STREAM4 | \
-							 ZYNQMP_DP_SOFTWARE_RESET_AUX)
+#define ZYNQMP_DP_TX_LINK_BW_SET			0x0
+#define ZYNQMP_DP_TX_LANE_CNT_SET			0x4
+#define ZYNQMP_DP_TX_ENHANCED_FRAME_EN			0x8
+#define ZYNQMP_DP_TX_TRAINING_PATTERN_SET		0xc
+#define ZYNQMP_DP_TX_SCRAMBLING_DISABLE			0x14
+#define ZYNQMP_DP_TX_DOWNSPREAD_CTL			0x18
+#define ZYNQMP_DP_TX_SW_RESET				0x1c
+#define ZYNQMP_DP_TX_SW_RESET_STREAM1			BIT(0)
+#define ZYNQMP_DP_TX_SW_RESET_STREAM2			BIT(1)
+#define ZYNQMP_DP_TX_SW_RESET_STREAM3			BIT(2)
+#define ZYNQMP_DP_TX_SW_RESET_STREAM4			BIT(3)
+#define ZYNQMP_DP_TX_SW_RESET_AUX			BIT(7)
+#define ZYNQMP_DP_TX_SW_RESET_ALL			(ZYNQMP_DP_TX_SW_RESET_STREAM1 | \
+							 ZYNQMP_DP_TX_SW_RESET_STREAM2 | \
+							 ZYNQMP_DP_TX_SW_RESET_STREAM3 | \
+							 ZYNQMP_DP_TX_SW_RESET_STREAM4 | \
+							 ZYNQMP_DP_TX_SW_RESET_AUX)
 
 /* Core enable registers */
-#define ZYNQMP_DP_TRANSMITTER_ENABLE			0x80
-#define ZYNQMP_DP_MAIN_STREAM_ENABLE			0x84
-#define ZYNQMP_DP_FORCE_SCRAMBLER_RESET			0xc0
-#define ZYNQMP_DP_VERSION				0xf8
-#define ZYNQMP_DP_VERSION_MAJOR_MASK			GENMASK(31, 24)
-#define ZYNQMP_DP_VERSION_MAJOR_SHIFT			24
-#define ZYNQMP_DP_VERSION_MINOR_MASK			GENMASK(23, 16)
-#define ZYNQMP_DP_VERSION_MINOR_SHIFT			16
-#define ZYNQMP_DP_VERSION_REVISION_MASK			GENMASK(15, 12)
-#define ZYNQMP_DP_VERSION_REVISION_SHIFT		12
-#define ZYNQMP_DP_VERSION_PATCH_MASK			GENMASK(11, 8)
-#define ZYNQMP_DP_VERSION_PATCH_SHIFT			8
-#define ZYNQMP_DP_VERSION_INTERNAL_MASK			GENMASK(7, 0)
-#define ZYNQMP_DP_VERSION_INTERNAL_SHIFT		0
+#define ZYNQMP_DP_TX_ENABLE				0x80
+#define ZYNQMP_DP_TX_ENABLE_MAIN_STREAM			0x84
+#define ZYNQMP_DP_TX_FORCE_SCRAMBLER_RESET		0xc0
+#define ZYNQMP_DP_TX_VERSION				0xf8
+#define ZYNQMP_DP_TX_VERSION_MAJOR_MASK			GENMASK(31, 24)
+#define ZYNQMP_DP_TX_VERSION_MAJOR_SHIFT		24
+#define ZYNQMP_DP_TX_VERSION_MINOR_MASK			GENMASK(23, 16)
+#define ZYNQMP_DP_TX_VERSION_MINOR_SHIFT		16
+#define ZYNQMP_DP_TX_VERSION_REVISION_MASK		GENMASK(15, 12)
+#define ZYNQMP_DP_TX_VERSION_REVISION_SHIFT		12
+#define ZYNQMP_DP_TX_VERSION_PATCH_MASK			GENMASK(11, 8)
+#define ZYNQMP_DP_TX_VERSION_PATCH_SHIFT		8
+#define ZYNQMP_DP_TX_VERSION_INTERNAL_MASK		GENMASK(7, 0)
+#define ZYNQMP_DP_TX_VERSION_INTERNAL_SHIFT		0
 
 /* Core ID registers */
-#define ZYNQMP_DP_CORE_ID				0xfc
-#define ZYNQMP_DP_CORE_ID_MAJOR_MASK			GENMASK(31, 24)
-#define ZYNQMP_DP_CORE_ID_MAJOR_SHIFT			24
-#define ZYNQMP_DP_CORE_ID_MINOR_MASK			GENMASK(23, 16)
-#define ZYNQMP_DP_CORE_ID_MINOR_SHIFT			16
-#define ZYNQMP_DP_CORE_ID_REVISION_MASK			GENMASK(15, 8)
-#define ZYNQMP_DP_CORE_ID_REVISION_SHIFT		8
-#define ZYNQMP_DP_CORE_ID_DIRECTION			GENMASK(1)
+#define ZYNQMP_DP_TX_CORE_ID				0xfc
+#define ZYNQMP_DP_TX_CORE_ID_MAJOR_MASK			GENMASK(31, 24)
+#define ZYNQMP_DP_TX_CORE_ID_MAJOR_SHIFT		24
+#define ZYNQMP_DP_TX_CORE_ID_MINOR_MASK			GENMASK(23, 16)
+#define ZYNQMP_DP_TX_CORE_ID_MINOR_SHIFT		16
+#define ZYNQMP_DP_TX_CORE_ID_REVISION_MASK		GENMASK(15, 8)
+#define ZYNQMP_DP_TX_CORE_ID_REVISION_SHIFT		8
+#define ZYNQMP_DP_TX_CORE_ID_DIRECTION			GENMASK(1)
 
 /* AUX channel interface registers */
-#define ZYNQMP_DP_AUX_COMMAND				0x100
-#define ZYNQMP_DP_AUX_COMMAND_CMD_SHIFT			8
-#define ZYNQMP_DP_AUX_COMMAND_ADDRESS_ONLY		BIT(12)
-#define ZYNQMP_DP_AUX_COMMAND_BYTES_SHIFT		0
-#define ZYNQMP_DP_AUX_WRITE_FIFO			0x104
-#define ZYNQMP_DP_AUX_ADDRESS				0x108
-#define ZYNQMP_DP_AUX_CLK_DIVIDER			0x10c
-#define ZYNQMP_DP_AUX_CLK_DIVIDER_AUX_FILTER_SHIFT	8
-#define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE		0x130
-#define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD		BIT(0)
-#define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REQUEST	BIT(1)
-#define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY		BIT(2)
-#define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY_TIMEOUT	BIT(3)
-#define ZYNQMP_DP_AUX_REPLY_DATA			0x134
-#define ZYNQMP_DP_AUX_REPLY_CODE			0x138
-#define ZYNQMP_DP_AUX_REPLY_CODE_AUX_ACK		(0)
-#define ZYNQMP_DP_AUX_REPLY_CODE_AUX_NACK		BIT(0)
-#define ZYNQMP_DP_AUX_REPLY_CODE_AUX_DEFER		BIT(1)
-#define ZYNQMP_DP_AUX_REPLY_CODE_I2C_ACK		(0)
-#define ZYNQMP_DP_AUX_REPLY_CODE_I2C_NACK		BIT(2)
-#define ZYNQMP_DP_AUX_REPLY_CODE_I2C_DEFER		BIT(3)
-#define ZYNQMP_DP_AUX_REPLY_COUNT			0x13c
-#define ZYNQMP_DP_REPLY_DATA_COUNT			0x148
-#define ZYNQMP_DP_REPLY_DATA_COUNT_MASK			0xff
-#define ZYNQMP_DP_INT_STATUS				0x3a0
-#define ZYNQMP_DP_INT_MASK				0x3a4
-#define ZYNQMP_DP_INT_EN				0x3a8
-#define ZYNQMP_DP_INT_DS				0x3ac
-#define ZYNQMP_DP_INT_HPD_IRQ				BIT(0)
-#define ZYNQMP_DP_INT_HPD_EVENT				BIT(1)
-#define ZYNQMP_DP_INT_REPLY_RECEIVED			BIT(2)
-#define ZYNQMP_DP_INT_REPLY_TIMEOUT			BIT(3)
-#define ZYNQMP_DP_INT_HPD_PULSE_DET			BIT(4)
-#define ZYNQMP_DP_INT_EXT_PKT_TXD			BIT(5)
-#define ZYNQMP_DP_INT_LIV_ABUF_UNDRFLW			BIT(12)
-#define ZYNQMP_DP_INT_VBLANK_START			BIT(13)
-#define ZYNQMP_DP_INT_PIXEL1_MATCH			BIT(14)
-#define ZYNQMP_DP_INT_PIXEL0_MATCH			BIT(15)
-#define ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK		0x3f0000
-#define ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK		0xfc00000
-#define ZYNQMP_DP_INT_CUST_TS_2				BIT(28)
-#define ZYNQMP_DP_INT_CUST_TS				BIT(29)
-#define ZYNQMP_DP_INT_EXT_VSYNC_TS			BIT(30)
-#define ZYNQMP_DP_INT_VSYNC_TS				BIT(31)
-#define ZYNQMP_DP_INT_ALL				(ZYNQMP_DP_INT_HPD_IRQ | \
-							 ZYNQMP_DP_INT_HPD_EVENT | \
-							 ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK | \
-							 ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK)
+#define ZYNQMP_DP_TX_AUX_COMMAND			0x100
+#define ZYNQMP_DP_TX_AUX_COMMAND_CMD_SHIFT		8
+#define ZYNQMP_DP_TX_AUX_COMMAND_ADDRESS_ONLY		BIT(12)
+#define ZYNQMP_DP_TX_AUX_COMMAND_BYTES_SHIFT		0
+#define ZYNQMP_DP_TX_AUX_WRITE_FIFO			0x104
+#define ZYNQMP_DP_TX_AUX_ADDRESS			0x108
+#define ZYNQMP_DP_TX_CLK_DIVIDER			0x10c
+#define ZYNQMP_DP_TX_CLK_DIVIDER_MHZ			1000000
+#define ZYNQMP_DP_TX_CLK_DIVIDER_AUX_FILTER_SHIFT	8
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE			0x130
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_HPD		BIT(0)
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REQUEST		BIT(1)
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY		BIT(2)
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY_TIMEOUT	BIT(3)
+#define ZYNQMP_DP_TX_AUX_REPLY_DATA			0x134
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE			0x138
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_ACK		(0)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_NACK		BIT(0)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_DEFER		BIT(1)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_ACK		(0)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_NACK		BIT(2)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_DEFER		BIT(3)
+#define ZYNQMP_DP_TX_AUX_REPLY_CNT			0x13c
+#define ZYNQMP_DP_TX_AUX_REPLY_CNT_MASK			0xff
+#define ZYNQMP_DP_TX_INTR_STATUS			0x140
+#define ZYNQMP_DP_TX_INTR_MASK				0x144
+#define ZYNQMP_DP_TX_INTR_HPD_IRQ			BIT(0)
+#define ZYNQMP_DP_TX_INTR_HPD_EVENT			BIT(1)
+#define ZYNQMP_DP_TX_INTR_REPLY_RECV			BIT(2)
+#define ZYNQMP_DP_TX_INTR_REPLY_TIMEOUT			BIT(3)
+#define ZYNQMP_DP_TX_INTR_HPD_PULSE			BIT(4)
+#define ZYNQMP_DP_TX_INTR_EXT_PKT_TXD			BIT(5)
+#define ZYNQMP_DP_TX_INTR_LIV_ABUF_UNDRFLW		BIT(12)
+#define ZYNQMP_DP_TX_INTR_VBLANK_START			BIT(13)
+#define ZYNQMP_DP_TX_INTR_PIXEL0_MATCH			BIT(14)
+#define ZYNQMP_DP_TX_INTR_PIXEL1_MATCH			BIT(15)
+#define ZYNQMP_DP_TX_INTR_CHBUF_UNDERFLW_MASK		0x3f0000
+#define ZYNQMP_DP_TX_INTR_CHBUF_OVERFLW_MASK		0xfc00000
+#define ZYNQMP_DP_TX_INTR_CUST_TS_2			BIT(28)
+#define ZYNQMP_DP_TX_INTR_CUST_TS			BIT(29)
+#define ZYNQMP_DP_TX_INTR_EXT_VSYNC_TS			BIT(30)
+#define ZYNQMP_DP_TX_INTR_VSYNC_TS			BIT(31)
+#define ZYNQMP_DP_TX_INTR_ALL				(ZYNQMP_DP_TX_INTR_HPD_IRQ | \
+							 ZYNQMP_DP_TX_INTR_HPD_EVENT | \
+							 ZYNQMP_DP_TX_INTR_REPLY_RECV | \
+							 ZYNQMP_DP_TX_INTR_REPLY_TIMEOUT | \
+							 ZYNQMP_DP_TX_INTR_HPD_PULSE | \
+							 ZYNQMP_DP_TX_INTR_EXT_PKT_TXD | \
+							 ZYNQMP_DP_TX_INTR_LIV_ABUF_UNDRFLW | \
+							 ZYNQMP_DP_TX_INTR_CHBUF_UNDERFLW_MASK | \
+							 ZYNQMP_DP_TX_INTR_CHBUF_OVERFLW_MASK)
+#define ZYNQMP_DP_TX_NO_INTR_ALL			(ZYNQMP_DP_TX_INTR_PIXEL0_MATCH | \
+							 ZYNQMP_DP_TX_INTR_PIXEL1_MATCH | \
+							 ZYNQMP_DP_TX_INTR_CUST_TS_2 | \
+							 ZYNQMP_DP_TX_INTR_CUST_TS | \
+							 ZYNQMP_DP_TX_INTR_EXT_VSYNC_TS | \
+							 ZYNQMP_DP_TX_INTR_VSYNC_TS)
+#define ZYNQMP_DP_TX_REPLY_DATA_CNT			0x148
+#define ZYNQMP_DP_SUB_TX_INTR_STATUS			0x3a0
+#define ZYNQMP_DP_SUB_TX_INTR_MASK			0x3a4
+#define ZYNQMP_DP_SUB_TX_INTR_EN			0x3a8
+#define ZYNQMP_DP_SUB_TX_INTR_DS			0x3ac
 
 /* Main stream attribute registers */
-#define ZYNQMP_DP_MAIN_STREAM_HTOTAL			0x180
-#define ZYNQMP_DP_MAIN_STREAM_VTOTAL			0x184
-#define ZYNQMP_DP_MAIN_STREAM_POLARITY			0x188
-#define ZYNQMP_DP_MAIN_STREAM_POLARITY_HSYNC_SHIFT	0
-#define ZYNQMP_DP_MAIN_STREAM_POLARITY_VSYNC_SHIFT	1
-#define ZYNQMP_DP_MAIN_STREAM_HSWIDTH			0x18c
-#define ZYNQMP_DP_MAIN_STREAM_VSWIDTH			0x190
-#define ZYNQMP_DP_MAIN_STREAM_HRES			0x194
-#define ZYNQMP_DP_MAIN_STREAM_VRES			0x198
-#define ZYNQMP_DP_MAIN_STREAM_HSTART			0x19c
-#define ZYNQMP_DP_MAIN_STREAM_VSTART			0x1a0
-#define ZYNQMP_DP_MAIN_STREAM_MISC0			0x1a4
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK		BIT(0)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_RGB	(0 << 1)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_422	(5 << 1)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_444	(6 << 1)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_MASK	(7 << 1)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_DYNAMIC_RANGE	BIT(3)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_YCBCR_COLR		BIT(4)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_6		(0 << 5)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8		(1 << 5)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_10		(2 << 5)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_12		(3 << 5)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_16		(4 << 5)
-#define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_MASK		(7 << 5)
-#define ZYNQMP_DP_MAIN_STREAM_MISC1			0x1a8
-#define ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN		BIT(7)
-#define ZYNQMP_DP_MAIN_STREAM_M_VID			0x1ac
-#define ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE		0x1b0
-#define ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE_TU_SIZE_DEF	64
-#define ZYNQMP_DP_MAIN_STREAM_N_VID			0x1b4
-#define ZYNQMP_DP_USER_PIX_WIDTH			0x1b8
-#define ZYNQMP_DP_USER_DATA_COUNT_PER_LANE		0x1bc
-#define ZYNQMP_DP_MIN_BYTES_PER_TU			0x1c4
-#define ZYNQMP_DP_FRAC_BYTES_PER_TU			0x1c8
-#define ZYNQMP_DP_INIT_WAIT				0x1cc
+#define ZYNQMP_DP_TX_MAIN_STREAM_HTOTAL			0x180
+#define ZYNQMP_DP_TX_MAIN_STREAM_VTOTAL			0x184
+#define ZYNQMP_DP_TX_MAIN_STREAM_POLARITY		0x188
+#define ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_HSYNC_SHIFT	0
+#define ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_VSYNC_SHIFT	1
+#define ZYNQMP_DP_TX_MAIN_STREAM_HSWIDTH		0x18c
+#define ZYNQMP_DP_TX_MAIN_STREAM_VSWIDTH		0x190
+#define ZYNQMP_DP_TX_MAIN_STREAM_HRES			0x194
+#define ZYNQMP_DP_TX_MAIN_STREAM_VRES			0x198
+#define ZYNQMP_DP_TX_MAIN_STREAM_HSTART			0x19c
+#define ZYNQMP_DP_TX_MAIN_STREAM_VSTART			0x1a0
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0			0x1a4
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC		BIT(0)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_FORMAT_SHIFT	1
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_DYNAMIC_RANGE	BIT(3)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_YCBCR_COLRIMETRY	BIT(4)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_BPC_SHIFT	5
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC1			0x1a8
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_INTERLACED_VERT	BIT(0)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_STEREO_VID_SHIFT	1
+#define ZYNQMP_DP_TX_M_VID				0x1ac
+#define ZYNQMP_DP_TX_TRANSFER_UNIT_SIZE			0x1b0
+#define ZYNQMP_DP_TX_DEF_TRANSFER_UNIT_SIZE		64
+#define ZYNQMP_DP_TX_N_VID				0x1b4
+#define ZYNQMP_DP_TX_USER_PIXEL_WIDTH			0x1b8
+#define ZYNQMP_DP_TX_USER_DATA_CNT_PER_LANE		0x1bc
+#define ZYNQMP_DP_TX_MIN_BYTES_PER_TU			0x1c4
+#define ZYNQMP_DP_TX_FRAC_BYTES_PER_TU			0x1c8
+#define ZYNQMP_DP_TX_INIT_WAIT				0x1cc
 
 /* PHY configuration and status registers */
-#define ZYNQMP_DP_PHY_RESET				0x200
-#define ZYNQMP_DP_PHY_RESET_PHY_RESET			BIT(0)
-#define ZYNQMP_DP_PHY_RESET_GTTX_RESET			BIT(1)
-#define ZYNQMP_DP_PHY_RESET_PHY_PMA_RESET		BIT(8)
-#define ZYNQMP_DP_PHY_RESET_PHY_PCS_RESET		BIT(9)
-#define ZYNQMP_DP_PHY_RESET_ALL_RESET			(ZYNQMP_DP_PHY_RESET_PHY_RESET | \
-							 ZYNQMP_DP_PHY_RESET_GTTX_RESET | \
-							 ZYNQMP_DP_PHY_RESET_PHY_PMA_RESET | \
-							 ZYNQMP_DP_PHY_RESET_PHY_PCS_RESET)
-#define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_0		0x210
-#define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_1		0x214
-#define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_2		0x218
-#define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_3		0x21c
-#define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_0		0x220
-#define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_1		0x224
-#define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_2		0x228
-#define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_3		0x22c
-#define ZYNQMP_DP_PHY_CLOCK_SELECT			0x234
-#define ZYNQMP_DP_PHY_CLOCK_SELECT_1_62G		0x1
-#define ZYNQMP_DP_PHY_CLOCK_SELECT_2_70G		0x3
-#define ZYNQMP_DP_PHY_CLOCK_SELECT_5_40G		0x5
+#define ZYNQMP_DP_TX_PHY_CONFIG				0x200
+#define ZYNQMP_DP_TX_PHY_CONFIG_PHY_RESET		BIT(0)
+#define ZYNQMP_DP_TX_PHY_CONFIG_GTTX_RESET		BIT(1)
+#define ZYNQMP_DP_TX_PHY_CONFIG_PHY_PMA_RESET		BIT(8)
+#define ZYNQMP_DP_TX_PHY_CONFIG_PHY_PCS_RESET		BIT(9)
+#define ZYNQMP_DP_TX_PHY_CONFIG_ALL_RESET		(ZYNQMP_DP_TX_PHY_CONFIG_PHY_RESET | \
+							 ZYNQMP_DP_TX_PHY_CONFIG_GTTX_RESET | \
+							 ZYNQMP_DP_TX_PHY_CONFIG_PHY_PMA_RESET | \
+							 ZYNQMP_DP_TX_PHY_CONFIG_PHY_PCS_RESET)
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_0		0x210
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_1		0x214
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_2		0x218
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_3		0x21c
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_0		0x220
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_1		0x224
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_2		0x228
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_3		0x22c
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING		0x234
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_162	0x1
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_270	0x3
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_540	0x5
 #define ZYNQMP_DP_TX_PHY_POWER_DOWN			0x238
 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_0		BIT(0)
 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_1		BIT(1)
 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_2		BIT(2)
 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_3		BIT(3)
 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL			0xf
-#define ZYNQMP_DP_PHY_PRECURSOR_LANE_0			0x23c
-#define ZYNQMP_DP_PHY_PRECURSOR_LANE_1			0x240
-#define ZYNQMP_DP_PHY_PRECURSOR_LANE_2			0x244
-#define ZYNQMP_DP_PHY_PRECURSOR_LANE_3			0x248
-#define ZYNQMP_DP_PHY_POSTCURSOR_LANE_0			0x24c
-#define ZYNQMP_DP_PHY_POSTCURSOR_LANE_1			0x250
-#define ZYNQMP_DP_PHY_POSTCURSOR_LANE_2			0x254
-#define ZYNQMP_DP_PHY_POSTCURSOR_LANE_3			0x258
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_0		0x23c
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_1		0x240
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_2		0x244
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_3		0x248
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_0		0x24c
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_1		0x250
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_2		0x254
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_3		0x258
 #define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0		0x24c
 #define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_1		0x250
-#define ZYNQMP_DP_PHY_STATUS				0x280
-#define ZYNQMP_DP_PHY_STATUS_PLL_LOCKED_SHIFT		4
-#define ZYNQMP_DP_PHY_STATUS_FPGA_PLL_LOCKED		BIT(6)
+#define ZYNQMP_DP_TX_PHY_STATUS				0x280
+#define ZYNQMP_DP_TX_PHY_STATUS_PLL_LOCKED_SHIFT	4
+#define ZYNQMP_DP_TX_PHY_STATUS_FPGA_PLL_LOCKED		BIT(6)
 
 /* Audio registers */
 #define ZYNQMP_DP_TX_AUDIO_CONTROL			0x300
 #define ZYNQMP_DP_TX_AUDIO_CHANNELS			0x304
 #define ZYNQMP_DP_TX_AUDIO_INFO_DATA			0x308
-#define ZYNQMP_DP_TX_M_AUD				0x328
-#define ZYNQMP_DP_TX_N_AUD				0x32c
+#define ZYNQMP_DP_TX_AUDIO_M_AUD			0x328
+#define ZYNQMP_DP_TX_AUDIO_N_AUD			0x32c
 #define ZYNQMP_DP_TX_AUDIO_EXT_DATA			0x330
 
+#define ZYNQMP_DP_MISC0_RGB				(0)
+#define ZYNQMP_DP_MISC0_YCRCB_422			(5 << 1)
+#define ZYNQMP_DP_MISC0_YCRCB_444			(6 << 1)
+#define ZYNQMP_DP_MISC0_FORMAT_MASK			0xe
+#define ZYNQMP_DP_MISC0_BPC_6				(0 << 5)
+#define ZYNQMP_DP_MISC0_BPC_8				(1 << 5)
+#define ZYNQMP_DP_MISC0_BPC_10				(2 << 5)
+#define ZYNQMP_DP_MISC0_BPC_12				(3 << 5)
+#define ZYNQMP_DP_MISC0_BPC_16				(4 << 5)
+#define ZYNQMP_DP_MISC0_BPC_MASK			0xe0
+#define ZYNQMP_DP_MISC1_Y_ONLY				(1 << 7)
+
 #define ZYNQMP_DP_MAX_LANES				2
 #define ZYNQMP_MAX_FREQ					3000000
 
@@ -267,17 +282,23 @@
  * @misc0: misc0 configuration (per DP v1.2 spec)
  * @misc1: misc1 configuration (per DP v1.2 spec)
  * @bpp: bits per pixel
+ * @bpc: bits per component
+ * @num_colors: number of color components
  */
 struct zynqmp_dp_config {
 	u8 misc0;
 	u8 misc1;
 	u8 bpp;
+	u8 bpc;
+	u8 num_colors;
 };
 
 /**
  * struct zynqmp_dp - Xilinx DisplayPort core
  * @encoder: the drm encoder structure
  * @connector: the drm connector structure
+ * @sync_prop: synchronous mode property
+ * @bpc_prop: bpc mode property
  * @dev: device structure
  * @dpsub: Display subsystem
  * @drm: DRM core
@@ -291,6 +312,7 @@
  * @hpd_work: hot plug detection worker
  * @status: connection status
  * @enabled: flag to indicate if the device is enabled
+ * @dpms: current dpms state
  * @dpcd: DP configuration data from currently connected sink device
  * @link_config: common link configuration between IP core and sink device
  * @mode: current mode between IP core and sink device
@@ -299,6 +321,8 @@
 struct zynqmp_dp {
 	struct drm_encoder encoder;
 	struct drm_connector connector;
+	struct drm_property *sync_prop;
+	struct drm_property *bpc_prop;
 	struct device *dev;
 	struct zynqmp_dpsub *dpsub;
 	struct drm_device *drm;
@@ -314,6 +338,7 @@
 	enum drm_connector_status status;
 	bool enabled;
 
+	int dpms;
 	u8 dpcd[DP_RECEIVER_CAP_SIZE];
 	struct zynqmp_dp_link_config link_config;
 	struct zynqmp_dp_mode mode;
@@ -330,30 +355,29 @@
 	return container_of(connector, struct zynqmp_dp, connector);
 }
 
-static void zynqmp_dp_write(struct zynqmp_dp *dp, int offset, u32 val)
+static void zynqmp_dp_write(void __iomem *base, int offset, u32 val)
 {
-	writel(val, dp->iomem + offset);
+	writel(val, base + offset);
 }
 
-static u32 zynqmp_dp_read(struct zynqmp_dp *dp, int offset)
+static u32 zynqmp_dp_read(void __iomem *base, int offset)
 {
-	return readl(dp->iomem + offset);
+	return readl(base + offset);
 }
 
-static void zynqmp_dp_clr(struct zynqmp_dp *dp, int offset, u32 clr)
+static void zynqmp_dp_clr(void __iomem *base, int offset, u32 clr)
 {
-	zynqmp_dp_write(dp, offset, zynqmp_dp_read(dp, offset) & ~clr);
+	zynqmp_dp_write(base, offset, zynqmp_dp_read(base, offset) & ~clr);
 }
 
-static void zynqmp_dp_set(struct zynqmp_dp *dp, int offset, u32 set)
+static void zynqmp_dp_set(void __iomem *base, int offset, u32 set)
 {
-	zynqmp_dp_write(dp, offset, zynqmp_dp_read(dp, offset) | set);
+	zynqmp_dp_write(base, offset, zynqmp_dp_read(base, offset) | set);
 }
 
 /* -----------------------------------------------------------------------------
  * PHY Handling
  */
-
 #define RST_TIMEOUT_MS			1000
 
 static int zynqmp_dp_reset(struct zynqmp_dp *dp, bool assert)
@@ -402,7 +426,8 @@
 		}
 	}
 
-	zynqmp_dp_clr(dp, ZYNQMP_DP_PHY_RESET, ZYNQMP_DP_PHY_RESET_ALL_RESET);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS, ZYNQMP_DP_TX_INTR_ALL);
+	zynqmp_dp_clr(dp->iomem, ZYNQMP_DP_TX_PHY_CONFIG, ZYNQMP_DP_TX_PHY_CONFIG_ALL_RESET);
 
 	/*
 	 * Power on lanes in reverse order as only lane 0 waits for the PLL to
@@ -512,7 +537,7 @@
 
 	/* Wait for 100 * 1ms. This should be enough time for PHY to be ready */
 	for (i = 0; ; i++) {
-		reg = zynqmp_dp_read(dp, ZYNQMP_DP_PHY_STATUS);
+		reg = zynqmp_dp_read(dp->iomem, ZYNQMP_DP_TX_PHY_STATUS);
 		if ((reg & ready) == ready)
 			return 0;
 
@@ -527,8 +552,112 @@
 	return 0;
 }
 
-/* -----------------------------------------------------------------------------
- * DisplayPort Link Training
+/*
+ * Internal functions: used by zynqmp_disp.c
+ */
+
+/**
+ * zynqmp_dp_update_bpp - Update the current bpp config
+ * @dp: DisplayPort IP core structure
+ *
+ * Update the current bpp based on the color format: bpc & num_colors.
+ * Any function that changes bpc or num_colors should call this
+ * to keep the bpp value in sync.
+ */
+static void zynqmp_dp_update_bpp(struct zynqmp_dp *dp)
+{
+	struct zynqmp_dp_config *config = &dp->config;
+
+	config->bpp = dp->config.bpc * dp->config.num_colors;
+}
+
+/**
+ * zynqmp_dp_set_color - Set the color
+ * @dp: DisplayPort IP core structure
+ * @color: color string, from zynqmp_disp_color_enum
+ *
+ * Update misc register values based on @color string.
+ *
+ * Return: 0 on success, or -EINVAL.
+ */
+int zynqmp_dp_set_color(struct zynqmp_dp *dp, const char *color)
+{
+	struct zynqmp_dp_config *config = &dp->config;
+
+	config->misc0 &= ~ZYNQMP_DP_MISC0_FORMAT_MASK;
+	config->misc1 &= ~ZYNQMP_DP_MISC1_Y_ONLY;
+	if (strcmp(color, "rgb") == 0) {
+		config->misc0 |= ZYNQMP_DP_MISC0_RGB;
+		config->num_colors = 3;
+	} else if (strcmp(color, "ycrcb422") == 0) {
+		config->misc0 |= ZYNQMP_DP_MISC0_YCRCB_422;
+		config->num_colors = 2;
+	} else if (strcmp(color, "ycrcb444") == 0) {
+		config->misc0 |= ZYNQMP_DP_MISC0_YCRCB_444;
+		config->num_colors = 3;
+	} else if (strcmp(color, "yonly") == 0) {
+		config->misc1 |= ZYNQMP_DP_MISC1_Y_ONLY;
+		config->num_colors = 1;
+	} else {
+		dev_err(dp->dev, "Invalid colormetry in DT\n");
+		return -EINVAL;
+	}
+	zynqmp_dp_update_bpp(dp);
+
+	return 0;
+}
+
+/**
+ * zynqmp_dp_enable_vblank - Enable vblank
+ * @dp: DisplayPort IP core structure
+ *
+ * Enable vblank interrupt
+ */
+void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp)
+{
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_EN,
+			ZYNQMP_DP_TX_INTR_VBLANK_START);
+}
+
+/**
+ * zynqmp_dp_disable_vblank - Disable vblank
+ * @dp: DisplayPort IP core structure
+ *
+ * Disable vblank interrupt
+ */
+void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp)
+{
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS,
+			ZYNQMP_DP_TX_INTR_VBLANK_START);
+}
+
+/*
+ * Power Management functions
+ */
+/**
+ * zynqmp_dp_pm_resume - Resume DP IP
+ * @dp: DisplayPort IP core structure
+ *
+ * Resume the DP IP including PHY and pipeline.
+ */
+void zynqmp_dp_pm_resume(struct zynqmp_dp *dp)
+{
+	zynqmp_dp_phy_init(dp);
+}
+
+/**
+ * zynqmp_dp_pm_suspend - Suspend DP IP
+ * @dp: DisplayPort IP core structure
+ *
+ * Suspend the DP IP including PHY and pipeline.
+ */
+void zynqmp_dp_pm_suspend(struct zynqmp_dp *dp)
+{
+	zynqmp_dp_phy_exit(dp);
+}
+
+/*
+ * DP functions
  */
 
 /**
@@ -648,10 +777,11 @@
  */
 static int zynqmp_dp_update_vs_emph(struct zynqmp_dp *dp)
 {
-	unsigned int i;
+	u8 *train_set = dp->train_set;
+	u8 i;
 	int ret;
 
-	ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, dp->train_set,
+	ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, train_set,
 				dp->mode.lane_cnt);
 	if (ret < 0)
 		return ret;
@@ -667,8 +797,7 @@
 			       >> DP_TRAIN_PRE_EMPHASIS_SHIFT;
 
 		phy_configure(dp->phy[i], &opts);
-
-		zynqmp_dp_write(dp, reg, 0x2);
+		zynqmp_dp_write(dp->iomem, reg, 0x2);
 	}
 
 	return 0;
@@ -690,7 +819,7 @@
 	bool cr_done;
 	int ret;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET,
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRAINING_PATTERN_SET,
 			DP_TRAINING_PATTERN_1);
 	ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
 				 DP_TRAINING_PATTERN_1 |
@@ -761,7 +890,7 @@
 	else
 		pat = DP_TRAINING_PATTERN_2;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, pat);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRAINING_PATTERN_SET, pat);
 	ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
 				 pat | DP_LINK_SCRAMBLING_DISABLE);
 	if (ret < 0)
@@ -791,7 +920,7 @@
 }
 
 /**
- * zynqmp_dp_link_train - Train the link
+ * zynqmp_dp_train - Train the link
  * @dp: DisplayPort IP core structure
  *
  * Return: 0 if all trains are done successfully, or corresponding error code.
@@ -805,19 +934,19 @@
 	bool enhanced;
 	int ret;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_LANE_COUNT_SET, lane_cnt);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_LANE_CNT_SET, lane_cnt);
 	enhanced = drm_dp_enhanced_frame_cap(dp->dpcd);
 	if (enhanced) {
-		zynqmp_dp_write(dp, ZYNQMP_DP_ENHANCED_FRAME_EN, 1);
+		zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENHANCED_FRAME_EN, 1);
 		aux_lane_cnt |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
 	}
 
 	if (dp->dpcd[3] & 0x1) {
-		zynqmp_dp_write(dp, ZYNQMP_DP_DOWNSPREAD_CTL, 1);
+		zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_DOWNSPREAD_CTL, 1);
 		drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL,
 				   DP_SPREAD_AMP_0_5);
 	} else {
-		zynqmp_dp_write(dp, ZYNQMP_DP_DOWNSPREAD_CTL, 0);
+		zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_DOWNSPREAD_CTL, 0);
 		drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, 0);
 	}
 
@@ -840,27 +969,28 @@
 		return ret;
 	}
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_LINK_BW_SET, bw_code);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_LINK_BW_SET, bw_code);
 	switch (bw_code) {
 	case DP_LINK_BW_1_62:
-		reg = ZYNQMP_DP_PHY_CLOCK_SELECT_1_62G;
+		reg = ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_162;
 		break;
 	case DP_LINK_BW_2_7:
-		reg = ZYNQMP_DP_PHY_CLOCK_SELECT_2_70G;
+		reg = ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_270;
 		break;
 	case DP_LINK_BW_5_4:
 	default:
-		reg = ZYNQMP_DP_PHY_CLOCK_SELECT_5_40G;
+		reg = ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_540;
 		break;
 	}
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_PHY_CLOCK_SELECT, reg);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING,
+			reg);
 	ret = zynqmp_dp_phy_ready(dp);
 	if (ret < 0)
 		return ret;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_SCRAMBLING_DISABLE, 1);
-	memset(dp->train_set, 0, sizeof(dp->train_set));
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_SCRAMBLING_DISABLE, 1);
+	memset(dp->train_set, 0, ARRAY_SIZE(dp->train_set));
 	ret = zynqmp_dp_link_train_cr(dp);
 	if (ret)
 		return ret;
@@ -875,10 +1005,10 @@
 		dev_err(dp->dev, "failed to disable training pattern\n");
 		return ret;
 	}
-	zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET,
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRAINING_PATTERN_SET,
 			DP_TRAINING_PATTERN_DISABLE);
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_SCRAMBLING_DISABLE, 0);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_SCRAMBLING_DISABLE, 0);
 
 	return 0;
 }
@@ -915,8 +1045,8 @@
 	dev_err(dp->dev, "failed to train the DP link\n");
 }
 
-/* -----------------------------------------------------------------------------
- * DisplayPort AUX
+/*
+ * DP Aux functions
  */
 
 #define AUX_READ_BIT	0x1
@@ -947,51 +1077,54 @@
 				    u8 *buf, u8 bytes, u8 *reply)
 {
 	bool is_read = (cmd & AUX_READ_BIT) ? true : false;
+	void __iomem *iomem = dp->iomem;
 	u32 reg, i;
 
-	reg = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE);
-	if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REQUEST)
+	reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_INTR_SIGNAL_STATE);
+	if (reg & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REQUEST)
 		return -EBUSY;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_AUX_ADDRESS, addr);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUX_ADDRESS, addr);
 	if (!is_read)
 		for (i = 0; i < bytes; i++)
-			zynqmp_dp_write(dp, ZYNQMP_DP_AUX_WRITE_FIFO,
+			zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUX_WRITE_FIFO,
 					buf[i]);
 
-	reg = cmd << ZYNQMP_DP_AUX_COMMAND_CMD_SHIFT;
+	reg = cmd << ZYNQMP_DP_TX_AUX_COMMAND_CMD_SHIFT;
 	if (!buf || !bytes)
-		reg |= ZYNQMP_DP_AUX_COMMAND_ADDRESS_ONLY;
+		reg |= ZYNQMP_DP_TX_AUX_COMMAND_ADDRESS_ONLY;
 	else
-		reg |= (bytes - 1) << ZYNQMP_DP_AUX_COMMAND_BYTES_SHIFT;
-	zynqmp_dp_write(dp, ZYNQMP_DP_AUX_COMMAND, reg);
+		reg |= (bytes - 1) << ZYNQMP_DP_TX_AUX_COMMAND_BYTES_SHIFT;
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUX_COMMAND, reg);
 
 	/* Wait for reply to be delivered upto 2ms */
 	for (i = 0; ; i++) {
-		reg = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE);
-		if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY)
+		reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_INTR_SIGNAL_STATE);
+		if (reg & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY)
 			break;
 
-		if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY_TIMEOUT ||
+		if (reg & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY_TIMEOUT ||
 		    i == 2)
 			return -ETIMEDOUT;
 
 		usleep_range(1000, 1100);
 	}
 
-	reg = zynqmp_dp_read(dp, ZYNQMP_DP_AUX_REPLY_CODE);
+	reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_AUX_REPLY_CODE);
 	if (reply)
 		*reply = reg;
 
 	if (is_read &&
-	    (reg == ZYNQMP_DP_AUX_REPLY_CODE_AUX_ACK ||
-	     reg == ZYNQMP_DP_AUX_REPLY_CODE_I2C_ACK)) {
-		reg = zynqmp_dp_read(dp, ZYNQMP_DP_REPLY_DATA_COUNT);
-		if ((reg & ZYNQMP_DP_REPLY_DATA_COUNT_MASK) != bytes)
+	    (reg == ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_ACK ||
+	     reg == ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_ACK)) {
+		reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_REPLY_DATA_CNT);
+		if ((reg & ZYNQMP_DP_TX_AUX_REPLY_CNT_MASK) != bytes)
 			return -EIO;
 
-		for (i = 0; i < bytes; i++)
-			buf[i] = zynqmp_dp_read(dp, ZYNQMP_DP_AUX_REPLY_DATA);
+		for (i = 0; i < bytes; i++) {
+			buf[i] = zynqmp_dp_read(iomem,
+						ZYNQMP_DP_TX_AUX_REPLY_DATA);
+		}
 	}
 
 	return 0;
@@ -1031,57 +1164,65 @@
 }
 
 /**
- * zynqmp_dp_aux_init - Initialize and register the DP AUX
+ * zynqmp_dp_init_aux - Initialize the DP aux
  * @dp: DisplayPort IP core structure
  *
- * Program the AUX clock divider and filter and register the DP AUX adapter.
+ * Initialize the DP aux. The aux clock is derived from the axi clock, so
+ * this function gets the axi clock frequency and calculates the filter
+ * value. Additionally, the interrupts and transmitter are enabled.
  *
  * Return: 0 on success, error value otherwise
  */
-static int zynqmp_dp_aux_init(struct zynqmp_dp *dp)
+static int zynqmp_dp_init_aux(struct zynqmp_dp *dp)
 {
-	unsigned long rate;
-	unsigned int w;
+	unsigned int rate;
+	u32 reg, w;
 
-	/*
-	 * The AUX_SIGNAL_WIDTH_FILTER is the number of APB clock cycles
-	 * corresponding to the AUX pulse. Allowable values are 8, 16, 24, 32,
-	 * 40 and 48. The AUX pulse width must be between 0.4µs and 0.6µs,
-	 * compute the w / 8 value corresponding to 0.4µs rounded up, and make
-	 * sure it stays below 0.6µs and within the allowable values.
-	 */
-	rate = clk_get_rate(dp->dpsub->apb_clk);
-	w = DIV_ROUND_UP(4 * rate, 1000 * 1000 * 10 * 8) * 8;
-	if (w > 6 * rate / (1000 * 1000 * 10) || w > 48) {
-		dev_err(dp->dev, "aclk frequency too high\n");
+	rate = zynqmp_disp_get_apb_clk_rate(dp->dpsub->disp);
+	if (rate < ZYNQMP_DP_TX_CLK_DIVIDER_MHZ) {
+		dev_err(dp->dev, "aclk should be higher than 1MHz\n");
 		return -EINVAL;
 	}
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_AUX_CLK_DIVIDER,
-			(w << ZYNQMP_DP_AUX_CLK_DIVIDER_AUX_FILTER_SHIFT) |
-			(rate / (1000 * 1000)));
+	/* Allowable values for this register are: 8, 16, 24, 32, 40, 48 */
+	for (w = 8; w <= 48; w += 8) {
+		/* AUX pulse width should be between 0.4 to 0.6 usec */
+		if (w >= (4 * rate / 10000000) &&
+		    w <= (6 * rate / 10000000))
+			break;
+	}
 
-	dp->aux.name = "ZynqMP DP AUX";
-	dp->aux.dev = dp->dev;
-	dp->aux.drm_dev = dp->drm;
-	dp->aux.transfer = zynqmp_dp_aux_transfer;
+	if (w > 48) {
+		dev_err(dp->dev, "aclk frequency too high\n");
+		return -EINVAL;
+	}
+	reg = w << ZYNQMP_DP_TX_CLK_DIVIDER_AUX_FILTER_SHIFT;
+	reg |= rate / ZYNQMP_DP_TX_CLK_DIVIDER_MHZ;
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_CLK_DIVIDER, reg);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_EN,
+			ZYNQMP_DP_TX_INTR_ALL);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS,
+			ZYNQMP_DP_TX_NO_INTR_ALL);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 1);
 
-	return drm_dp_aux_register(&dp->aux);
+	return 0;
 }
 
 /**
- * zynqmp_dp_aux_cleanup - Cleanup the DP AUX
+ * zynqmp_dp_exit_aux - De-initialize the DP aux
  * @dp: DisplayPort IP core structure
  *
- * Unregister the DP AUX adapter.
+ * De-initialize the DP aux. Disable all interrupts which are enabled
+ * through aux initialization, as well as the transmitter.
  */
-static void zynqmp_dp_aux_cleanup(struct zynqmp_dp *dp)
+static void zynqmp_dp_exit_aux(struct zynqmp_dp *dp)
 {
-	drm_dp_aux_unregister(&dp->aux);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 0);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS, 0xffffffff);
 }
 
-/* -----------------------------------------------------------------------------
- * DisplayPort Generic Support
+/*
+ * Generic DP functions
  */
 
 /**
@@ -1093,95 +1234,101 @@
  */
 static void zynqmp_dp_update_misc(struct zynqmp_dp *dp)
 {
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_MISC0, dp->config.misc0);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_MISC1, dp->config.misc1);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_MAIN_STREAM_MISC0,
+			dp->config.misc0);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_MAIN_STREAM_MISC1,
+			dp->config.misc1);
 }
 
 /**
- * zynqmp_dp_set_format - Set the input format
+ * zynqmp_dp_set_sync_mode - Set the sync mode bit in the software misc state
  * @dp: DisplayPort IP core structure
- * @format: input format
- * @bpc: bits per component
+ * @mode: flag if the sync mode should be on or off
  *
- * Update misc register values based on input @format and @bpc.
- *
- * Return: 0 on success, or -EINVAL.
+ * Set the bit in software misc state. To apply to hardware,
+ * zynqmp_dp_update_misc() should be called.
  */
-static int zynqmp_dp_set_format(struct zynqmp_dp *dp,
-				enum zynqmp_dpsub_format format,
-				unsigned int bpc)
+static void zynqmp_dp_set_sync_mode(struct zynqmp_dp *dp, bool mode)
 {
-	static const struct drm_display_info *display;
 	struct zynqmp_dp_config *config = &dp->config;
-	unsigned int num_colors;
 
-	config->misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_MASK;
-	config->misc1 &= ~ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN;
-
-	switch (format) {
-	case ZYNQMP_DPSUB_FORMAT_RGB:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_RGB;
-		num_colors = 3;
-		break;
-
-	case ZYNQMP_DPSUB_FORMAT_YCRCB444:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_444;
-		num_colors = 3;
-		break;
+	if (mode)
+		config->misc0 |= ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+	else
+		config->misc0 &= ~ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+}
 
-	case ZYNQMP_DPSUB_FORMAT_YCRCB422:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_422;
-		num_colors = 2;
-		break;
+/**
+ * zynqmp_dp_get_sync_mode - Get the sync mode state
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: true if the sync mode is on, or false
+ */
+static bool zynqmp_dp_get_sync_mode(struct zynqmp_dp *dp)
+{
+	struct zynqmp_dp_config *config = &dp->config;
 
-	case ZYNQMP_DPSUB_FORMAT_YONLY:
-		config->misc1 |= ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN;
-		num_colors = 1;
-		break;
+	return !!(config->misc0 & ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC);
+}
 
-	default:
-		dev_err(dp->dev, "Invalid colormetry in DT\n");
-		return -EINVAL;
-	}
+/**
+ * zynqmp_dp_set_bpc - Set bpc value in software misc state
+ * @dp: DisplayPort IP core structure
+ * @bpc: bits per component
+ *
+ * Return: 0 on success, or the fallback bpc value
+ */
+static u8 zynqmp_dp_set_bpc(struct zynqmp_dp *dp, u8 bpc)
+{
+	struct zynqmp_dp_config *config = &dp->config;
+	u8 ret = 0;
 
-	display = &dp->connector.display_info;
-	if (display->bpc && bpc > display->bpc) {
-		dev_warn(dp->dev,
-			 "downgrading requested %ubpc to display limit %ubpc\n",
-			 bpc, display->bpc);
-		bpc = display->bpc;
+	if (dp->connector.display_info.bpc &&
+	    dp->connector.display_info.bpc != bpc) {
+		dev_err(dp->dev, "requested bpc (%u) != display info (%u)\n",
+			bpc, dp->connector.display_info.bpc);
+		bpc = dp->connector.display_info.bpc;
 	}
 
-	config->misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_MASK;
-
+	config->misc0 &= ~ZYNQMP_DP_MISC0_BPC_MASK;
 	switch (bpc) {
 	case 6:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_6;
+		config->misc0 |= ZYNQMP_DP_MISC0_BPC_6;
 		break;
 	case 8:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8;
+		config->misc0 |= ZYNQMP_DP_MISC0_BPC_8;
 		break;
 	case 10:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_10;
+		config->misc0 |= ZYNQMP_DP_MISC0_BPC_10;
 		break;
 	case 12:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_12;
+		config->misc0 |= ZYNQMP_DP_MISC0_BPC_12;
 		break;
 	case 16:
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_16;
+		config->misc0 |= ZYNQMP_DP_MISC0_BPC_16;
 		break;
 	default:
-		dev_warn(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n",
-			 bpc);
-		config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8;
-		bpc = 8;
+		dev_err(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n",
+			bpc);
+		config->misc0 |= ZYNQMP_DP_MISC0_BPC_8;
+		ret = 8;
 		break;
 	}
+	config->bpc = bpc;
+	zynqmp_dp_update_bpp(dp);
 
-	/* Update the current bpp based on the format. */
-	config->bpp = bpc * num_colors;
+	return ret;
+}
 
-	return 0;
+/**
+ * zynqmp_dp_get_bpc - Set bpc value from software state
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: current bpc value
+ */
+static u8 zynqmp_dp_get_bpc(struct zynqmp_dp *dp)
+{
+	return dp->config.bpc;
 }
 
 /**
@@ -1196,18 +1343,18 @@
 zynqmp_dp_encoder_mode_set_transfer_unit(struct zynqmp_dp *dp,
 					 struct drm_display_mode *mode)
 {
-	u32 tu = ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE_TU_SIZE_DEF;
+	u32 tu = ZYNQMP_DP_TX_DEF_TRANSFER_UNIT_SIZE;
 	u32 bw, vid_kbytes, avg_bytes_per_tu, init_wait;
 
 	/* Use the max transfer unit size (default) */
-	zynqmp_dp_write(dp, ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE, tu);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRANSFER_UNIT_SIZE, tu);
 
 	vid_kbytes = mode->clock * (dp->config.bpp / 8);
 	bw = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
 	avg_bytes_per_tu = vid_kbytes * tu / (dp->mode.lane_cnt * bw / 1000);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MIN_BYTES_PER_TU,
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_MIN_BYTES_PER_TU,
 			avg_bytes_per_tu / 1000);
-	zynqmp_dp_write(dp, ZYNQMP_DP_FRAC_BYTES_PER_TU,
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_FRAC_BYTES_PER_TU,
 			avg_bytes_per_tu % 1000);
 
 	/* Configure the initial wait cycle based on transfer unit size */
@@ -1218,7 +1365,7 @@
 	else
 		init_wait = tu - avg_bytes_per_tu / 1000;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_INIT_WAIT, init_wait);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_INIT_WAIT, init_wait);
 }
 
 /**
@@ -1229,58 +1376,60 @@
  * Configure the main stream based on the requested mode @mode. Calculation is
  * based on IP core specification.
  */
-static void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp,
-					      const struct drm_display_mode *mode)
+void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp,
+				       struct drm_display_mode *mode)
 {
+	void __iomem *iomem = dp->iomem;
 	u8 lane_cnt = dp->mode.lane_cnt;
 	u32 reg, wpl;
 	unsigned int rate;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HTOTAL, mode->htotal);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VTOTAL, mode->vtotal);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_POLARITY,
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HTOTAL, mode->htotal);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VTOTAL, mode->vtotal);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_POLARITY,
 			(!!(mode->flags & DRM_MODE_FLAG_PVSYNC) <<
-			 ZYNQMP_DP_MAIN_STREAM_POLARITY_VSYNC_SHIFT) |
+			 ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_VSYNC_SHIFT) |
 			(!!(mode->flags & DRM_MODE_FLAG_PHSYNC) <<
-			 ZYNQMP_DP_MAIN_STREAM_POLARITY_HSYNC_SHIFT));
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HSWIDTH,
+			 ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_HSYNC_SHIFT));
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HSWIDTH,
 			mode->hsync_end - mode->hsync_start);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VSWIDTH,
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VSWIDTH,
 			mode->vsync_end - mode->vsync_start);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HRES, mode->hdisplay);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VRES, mode->vdisplay);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HSTART,
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HRES, mode->hdisplay);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VRES, mode->vdisplay);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HSTART,
 			mode->htotal - mode->hsync_start);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VSTART,
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VSTART,
 			mode->vtotal - mode->vsync_start);
 
 	/* In synchronous mode, set the diviers */
-	if (dp->config.misc0 & ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK) {
+	if (dp->config.misc0 & ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC) {
 		reg = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
-		zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_N_VID, reg);
-		zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_M_VID, mode->clock);
-		rate = zynqmp_disp_get_audio_clk_rate(dp->dpsub->disp);
+		zynqmp_dp_write(iomem, ZYNQMP_DP_TX_N_VID, reg);
+		zynqmp_dp_write(iomem, ZYNQMP_DP_TX_M_VID, mode->clock);
+		rate = zynqmp_disp_get_aud_clk_rate(dp->dpsub->disp);
 		if (rate) {
 			dev_dbg(dp->dev, "Audio rate: %d\n", rate / 512);
-			zynqmp_dp_write(dp, ZYNQMP_DP_TX_N_AUD, reg);
-			zynqmp_dp_write(dp, ZYNQMP_DP_TX_M_AUD, rate / 1000);
+			zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_N_AUD, reg);
+			zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_M_AUD,
+					rate / 1000);
 		}
 	}
 
 	/* Only 2 channel audio is supported now */
-	if (zynqmp_disp_audio_enabled(dp->dpsub->disp))
-		zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CHANNELS, 1);
+	if (zynqmp_disp_aud_enabled(dp->dpsub->disp))
+		zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_CHANNELS, 1);
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_USER_PIX_WIDTH, 1);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_USER_PIXEL_WIDTH, 1);
 
 	/* Translate to the native 16 bit datapath based on IP core spec */
 	wpl = (mode->hdisplay * dp->config.bpp + 15) / 16;
 	reg = wpl + wpl % lane_cnt - lane_cnt;
-	zynqmp_dp_write(dp, ZYNQMP_DP_USER_DATA_COUNT_PER_LANE, reg);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_USER_DATA_CNT_PER_LANE, reg);
 }
 
-/* -----------------------------------------------------------------------------
- * DRM Connector
+/*
+ * DRM connector functions
  */
 
 static enum drm_connector_status
@@ -1296,18 +1445,25 @@
 	 * get the HPD signal with some monitors.
 	 */
 	for (i = 0; i < 10; i++) {
-		state = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE);
-		if (state & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD)
+		state = zynqmp_dp_read(dp->iomem,
+				       ZYNQMP_DP_TX_INTR_SIGNAL_STATE);
+		if (state & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_HPD)
 			break;
 		msleep(100);
 	}
 
-	if (state & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD) {
+	if (state & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_HPD) {
+		dp->status = connector_status_connected;
 		ret = drm_dp_dpcd_read(&dp->aux, 0x0, dp->dpcd,
 				       sizeof(dp->dpcd));
 		if (ret < 0) {
-			dev_dbg(dp->dev, "DPCD read failed");
-			goto disconnected;
+			dev_dbg(dp->dev, "DPCD read first try fails");
+			ret = drm_dp_dpcd_read(&dp->aux, 0x0, dp->dpcd,
+					       sizeof(dp->dpcd));
+			if (ret < 0) {
+				dev_dbg(dp->dev, "DPCD read retry fails");
+				goto disconnected;
+			}
 		}
 
 		link_config->max_rate = min_t(int,
@@ -1317,7 +1473,6 @@
 					       drm_dp_max_lane_count(dp->dpcd),
 					       dp->num_lanes);
 
-		dp->status = connector_status_connected;
 		return connector_status_connected;
 	}
 
@@ -1379,38 +1534,96 @@
 	return MODE_OK;
 }
 
+static void zynqmp_dp_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+}
+
+static int
+zynqmp_dp_connector_atomic_set_property(struct drm_connector *connector,
+					struct drm_connector_state *state,
+					struct drm_property *property,
+					uint64_t val)
+{
+	struct zynqmp_dp *dp = connector_to_dp(connector);
+
+	if (property == dp->sync_prop) {
+		zynqmp_dp_set_sync_mode(dp, val);
+	} else if (property == dp->bpc_prop) {
+		u8 bpc;
+
+		bpc = zynqmp_dp_set_bpc(dp, val);
+		if (bpc) {
+			drm_object_property_set_value(&connector->base,
+						      property, bpc);
+			return -EINVAL;
+		}
+	} else {
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int
+zynqmp_dp_connector_atomic_get_property(struct drm_connector *connector,
+					const struct drm_connector_state *state,
+					struct drm_property *property,
+					uint64_t *val)
+{
+	struct zynqmp_dp *dp = connector_to_dp(connector);
+
+	if (property == dp->sync_prop)
+		*val = zynqmp_dp_get_sync_mode(dp);
+	else if (property == dp->bpc_prop)
+		*val =  zynqmp_dp_get_bpc(dp);
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
 static const struct drm_connector_funcs zynqmp_dp_connector_funcs = {
 	.detect			= zynqmp_dp_connector_detect,
 	.fill_modes		= drm_helper_probe_single_connector_modes,
-	.destroy		= drm_connector_cleanup,
+	.destroy		= zynqmp_dp_connector_destroy,
 	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
 	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
 	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_set_property	= zynqmp_dp_connector_atomic_set_property,
+	.atomic_get_property	= zynqmp_dp_connector_atomic_get_property,
 };
 
-static const struct drm_connector_helper_funcs
-zynqmp_dp_connector_helper_funcs = {
+static struct drm_connector_helper_funcs zynqmp_dp_connector_helper_funcs = {
 	.get_modes	= zynqmp_dp_connector_get_modes,
 	.best_encoder	= zynqmp_dp_connector_best_encoder,
 	.mode_valid	= zynqmp_dp_connector_mode_valid,
 };
 
-/* -----------------------------------------------------------------------------
- * DRM Encoder
+/*
+ * DRM encoder functions
  */
 
 static void zynqmp_dp_encoder_enable(struct drm_encoder *encoder)
 {
 	struct zynqmp_dp *dp = encoder_to_dp(encoder);
+	void __iomem *iomem = dp->iomem;
 	unsigned int i;
 	int ret = 0;
 
-	pm_runtime_get_sync(dp->dev);
+	ret = pm_runtime_get_sync(dp->dev);
+	if (ret < 0) {
+		dev_err(dp->dev, "IRQ sync failed to resume: %d\n", ret);
+		return;
+	}
+
 	dp->enabled = true;
+	zynqmp_dp_init_aux(dp);
 	zynqmp_dp_update_misc(dp);
-	if (zynqmp_disp_audio_enabled(dp->dpsub->disp))
-		zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 1);
-	zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 0);
+	if (zynqmp_disp_aud_enabled(dp->dpsub->disp))
+		zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_CONTROL, 1);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_PHY_POWER_DOWN, 0);
 	if (dp->status == connector_status_connected) {
 		for (i = 0; i < 3; i++) {
 			ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER,
@@ -1426,23 +1639,35 @@
 		dev_dbg(dp->dev, "DP aux failed\n");
 	else
 		zynqmp_dp_train_loop(dp);
-	zynqmp_dp_write(dp, ZYNQMP_DP_SOFTWARE_RESET,
-			ZYNQMP_DP_SOFTWARE_RESET_ALL);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 1);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_SW_RESET,
+			ZYNQMP_DP_TX_SW_RESET_ALL);
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_ENABLE_MAIN_STREAM, 1);
 }
 
 static void zynqmp_dp_encoder_disable(struct drm_encoder *encoder)
 {
 	struct zynqmp_dp *dp = encoder_to_dp(encoder);
+	void __iomem *iomem = dp->iomem;
+	int ret;
+	u8 pwr;
 
 	dp->enabled = false;
 	cancel_delayed_work(&dp->hpd_work);
-	zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 0);
-	drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
-	zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN,
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_ENABLE_MAIN_STREAM, 0);
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_SET_POWER, &pwr);
+	/* Do write only if read succeeds */
+	if (ret >= 0) {
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
+		if (ret < 0) {
+			dev_err(dp->dev, "failed to write a byte to the DPCD: %d\n",
+				ret);
+			return;
+		}
+	}
+	zynqmp_dp_write(iomem, ZYNQMP_DP_TX_PHY_POWER_DOWN,
 			ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL);
-	if (zynqmp_disp_audio_enabled(dp->dpsub->disp))
-		zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 0);
+	if (zynqmp_disp_aud_enabled(dp->dpsub->disp))
+		zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_CONTROL, 0);
 	pm_runtime_put_sync(dp->dev);
 }
 
@@ -1459,8 +1684,6 @@
 	int rate, max_rate = dp->link_config.max_rate;
 	int ret;
 
-	zynqmp_dp_set_format(dp, ZYNQMP_DPSUB_FORMAT_RGB, 8);
-
 	/* Check again as bpp or format might have been chagned */
 	rate = zynqmp_dp_max_rate(max_rate, max_lanes, bpp);
 	if (mode->clock > rate) {
@@ -1474,7 +1697,6 @@
 		return;
 
 	zynqmp_dp_encoder_mode_set_transfer_unit(dp, adjusted_mode);
-	zynqmp_dp_encoder_mode_set_stream(dp, adjusted_mode);
 }
 
 #define ZYNQMP_DP_MIN_H_BACKPORCH	20
@@ -1484,29 +1706,30 @@
 			       struct drm_crtc_state *crtc_state,
 			       struct drm_connector_state *conn_state)
 {
-	struct drm_display_mode *mode = &crtc_state->mode;
 	struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
-	int diff = mode->htotal - mode->hsync_end;
+	int diff = adjusted_mode->htotal - adjusted_mode->hsync_end;
 
 	/*
 	 * ZynqMP DP requires horizontal backporch to be greater than 12.
 	 * This limitation may not be compatible with the sink device.
 	 */
 	if (diff < ZYNQMP_DP_MIN_H_BACKPORCH) {
-		int vrefresh = (adjusted_mode->clock * 1000) /
-			       (adjusted_mode->vtotal * adjusted_mode->htotal);
-
 		dev_dbg(encoder->dev->dev, "hbackporch adjusted: %d to %d",
 			diff, ZYNQMP_DP_MIN_H_BACKPORCH - diff);
 		diff = ZYNQMP_DP_MIN_H_BACKPORCH - diff;
 		adjusted_mode->htotal += diff;
-		adjusted_mode->clock = adjusted_mode->vtotal *
-				       adjusted_mode->htotal * vrefresh / 1000;
+		adjusted_mode->clock = (adjusted_mode->clock *
+					adjusted_mode->htotal) /
+				       (adjusted_mode->htotal - diff);
 	}
 
 	return 0;
 }
 
+static const struct drm_encoder_funcs zynqmp_dp_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
 static const struct drm_encoder_helper_funcs zynqmp_dp_encoder_helper_funcs = {
 	.enable			= zynqmp_dp_encoder_enable,
 	.disable		= zynqmp_dp_encoder_disable,
@@ -1514,78 +1737,157 @@
 	.atomic_check		= zynqmp_dp_encoder_atomic_check,
 };
 
-/* -----------------------------------------------------------------------------
- * Interrupt Handling
+/*
+ * Component functions
  */
 
-/**
- * zynqmp_dp_enable_vblank - Enable vblank
- * @dp: DisplayPort IP core structure
- *
- * Enable vblank interrupt
- */
-void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp)
+static void zynqmp_dp_hpd_work_func(struct work_struct *work)
 {
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_EN, ZYNQMP_DP_INT_VBLANK_START);
+	struct zynqmp_dp *dp;
+
+	dp = container_of(work, struct zynqmp_dp, hpd_work.work);
+
+	if (dp->drm)
+		drm_helper_hpd_irq_event(dp->drm);
 }
 
-/**
- * zynqmp_dp_disable_vblank - Disable vblank
- * @dp: DisplayPort IP core structure
- *
- * Disable vblank interrupt
- */
-void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp)
+static struct drm_prop_enum_list zynqmp_dp_bpc_enum[] = {
+	{ 6, "6BPC" },
+	{ 8, "8BPC" },
+	{ 10, "10BPC" },
+	{ 12, "12BPC" },
+};
+
+int zynqmp_dp_bind(struct device *dev, struct device *master, void *data)
 {
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, ZYNQMP_DP_INT_VBLANK_START);
+	struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+	struct zynqmp_dp *dp = dpsub->dp;
+	struct drm_encoder *encoder = &dp->encoder;
+	struct drm_connector *connector = &dp->connector;
+	struct drm_device *drm = data;
+	int ret;
+
+	if (!dp->num_lanes)
+		return 0;
+
+	encoder->possible_crtcs |= zynqmp_disp_get_crtc_mask(dpsub->disp);
+	if (dpsub->external_crtc_attached)
+		encoder->possible_crtcs |=
+			drm_of_find_possible_crtcs(drm, dev->of_node);
+
+	drm_encoder_init(drm, encoder, &zynqmp_dp_encoder_funcs,
+			 DRM_MODE_ENCODER_TMDS, NULL);
+	drm_encoder_helper_add(encoder, &zynqmp_dp_encoder_helper_funcs);
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+	ret = drm_connector_init(encoder->dev, connector,
+				 &zynqmp_dp_connector_funcs,
+				 DRM_MODE_CONNECTOR_DisplayPort);
+	if (ret) {
+		dev_err(dp->dev, "failed to initialize the drm connector");
+		goto error_encoder;
+	}
+
+	drm_connector_helper_add(connector, &zynqmp_dp_connector_helper_funcs);
+	drm_connector_register(connector);
+	drm_connector_attach_encoder(connector, encoder);
+	connector->dpms = DRM_MODE_DPMS_OFF;
+
+	dp->drm = drm;
+	dp->aux.drm_dev = drm;
+	dp->sync_prop = drm_property_create_bool(drm, 0, "sync");
+	dp->bpc_prop = drm_property_create_enum(drm, 0, "bpc",
+						zynqmp_dp_bpc_enum,
+						ARRAY_SIZE(zynqmp_dp_bpc_enum));
+
+	dp->config.misc0 &= ~ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+	drm_object_attach_property(&connector->base, dp->sync_prop, false);
+	ret = zynqmp_dp_set_bpc(dp, 8);
+	drm_object_attach_property(&connector->base, dp->bpc_prop,
+				   ret ? ret : 8);
+	zynqmp_dp_update_bpp(dp);
+
+	INIT_DELAYED_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func);
+
+	/* This enables interrupts, so should be called after DRM init */
+	ret = zynqmp_dp_init_aux(dp);
+	if (ret) {
+		dev_err(dp->dev, "failed to initialize DP aux");
+		goto error_prop;
+	}
+
+	return 0;
+
+error_prop:
+	drm_property_destroy(dp->drm, dp->bpc_prop);
+	drm_property_destroy(dp->drm, dp->sync_prop);
+	zynqmp_dp_connector_destroy(&dp->connector);
+error_encoder:
+	drm_encoder_cleanup(&dp->encoder);
+	return ret;
 }
 
-static void zynqmp_dp_hpd_work_func(struct work_struct *work)
+void zynqmp_dp_unbind(struct device *dev, struct device *master, void *data)
 {
-	struct zynqmp_dp *dp;
+	struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+	struct zynqmp_dp *dp = dpsub->dp;
 
-	dp = container_of(work, struct zynqmp_dp, hpd_work.work);
+	disable_irq(dp->irq);
+	if (!dp->num_lanes)
+		return;
 
-	if (dp->drm)
-		drm_helper_hpd_irq_event(dp->drm);
+	cancel_delayed_work_sync(&dp->hpd_work);
+	zynqmp_dp_exit_aux(dp);
+	drm_property_destroy(dp->drm, dp->bpc_prop);
+	drm_property_destroy(dp->drm, dp->sync_prop);
+	zynqmp_dp_connector_destroy(&dp->connector);
+	drm_encoder_cleanup(&dp->encoder);
 }
 
+/*
+ * Platform functions
+ */
+
 static irqreturn_t zynqmp_dp_irq_handler(int irq, void *data)
 {
 	struct zynqmp_dp *dp = (struct zynqmp_dp *)data;
 	u32 status, mask;
 
-	status = zynqmp_dp_read(dp, ZYNQMP_DP_INT_STATUS);
-	mask = zynqmp_dp_read(dp, ZYNQMP_DP_INT_MASK);
+	status = zynqmp_dp_read(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_STATUS);
+	mask = zynqmp_dp_read(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_MASK);
 	if (!(status & ~mask))
 		return IRQ_NONE;
 
 	/* dbg for diagnostic, but not much that the driver can do */
-	if (status & ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK)
+	if (status & ZYNQMP_DP_TX_INTR_CHBUF_UNDERFLW_MASK)
 		dev_dbg_ratelimited(dp->dev, "underflow interrupt\n");
-	if (status & ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK)
+	if (status & ZYNQMP_DP_TX_INTR_CHBUF_OVERFLW_MASK)
 		dev_dbg_ratelimited(dp->dev, "overflow interrupt\n");
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_STATUS, status);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_STATUS, status);
 
-	if (status & ZYNQMP_DP_INT_VBLANK_START)
+	/* The DP vblank will not be enabled with remote crtc device */
+	if (status & ZYNQMP_DP_TX_INTR_VBLANK_START &&
+	    !dp->dpsub->external_crtc_attached)
 		zynqmp_disp_handle_vblank(dp->dpsub->disp);
 
-	if (status & ZYNQMP_DP_INT_HPD_EVENT)
+	if (status & ZYNQMP_DP_TX_INTR_HPD_EVENT)
 		schedule_delayed_work(&dp->hpd_work, 0);
 
-	if (status & ZYNQMP_DP_INT_HPD_IRQ) {
+	if (status & ZYNQMP_DP_TX_INTR_HPD_IRQ) {
 		int ret;
-		u8 status[DP_LINK_STATUS_SIZE + 2];
+		u8 buf[DP_LINK_STATUS_SIZE + 2];
 
-		ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT, status,
+		memset(buf, 0, ARRAY_SIZE(buf));
+
+		ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT, buf,
 				       DP_LINK_STATUS_SIZE + 2);
 		if (ret < 0)
 			goto handled;
 
-		if (status[4] & DP_LINK_STATUS_UPDATED ||
-		    !drm_dp_clock_recovery_ok(&status[2], dp->mode.lane_cnt) ||
-		    !drm_dp_channel_eq_ok(&status[2], dp->mode.lane_cnt)) {
+		if (buf[4] & DP_LINK_STATUS_UPDATED ||
+		    !drm_dp_clock_recovery_ok(&buf[2], dp->mode.lane_cnt) ||
+		    !drm_dp_channel_eq_ok(&buf[2], dp->mode.lane_cnt)) {
 			zynqmp_dp_train_loop(dp);
 		}
 	}
@@ -1594,127 +1896,94 @@
 	return IRQ_HANDLED;
 }
 
-/* -----------------------------------------------------------------------------
- * Initialization & Cleanup
- */
-
-int zynqmp_dp_drm_init(struct zynqmp_dpsub *dpsub)
+int zynqmp_dp_probe(struct platform_device *pdev)
 {
-	struct zynqmp_dp *dp = dpsub->dp;
-	struct drm_encoder *encoder = &dp->encoder;
-	struct drm_connector *connector = &dp->connector;
-	int ret;
-
-	dp->config.misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK;
-	zynqmp_dp_set_format(dp, ZYNQMP_DPSUB_FORMAT_RGB, 8);
-
-	/* Create the DRM encoder and connector. */
-	encoder->possible_crtcs |= zynqmp_disp_get_crtc_mask(dpsub->disp);
-	drm_simple_encoder_init(dp->drm, encoder, DRM_MODE_ENCODER_TMDS);
-	drm_encoder_helper_add(encoder, &zynqmp_dp_encoder_helper_funcs);
-
-	connector->polled = DRM_CONNECTOR_POLL_HPD;
-	ret = drm_connector_init(encoder->dev, connector,
-				 &zynqmp_dp_connector_funcs,
-				 DRM_MODE_CONNECTOR_DisplayPort);
-	if (ret) {
-		dev_err(dp->dev, "failed to create the DRM connector\n");
-		return ret;
-	}
-
-	drm_connector_helper_add(connector, &zynqmp_dp_connector_helper_funcs);
-	drm_connector_register(connector);
-	drm_connector_attach_encoder(connector, encoder);
-
-	/* Initialize and register the AUX adapter. */
-	ret = zynqmp_dp_aux_init(dp);
-	if (ret) {
-		dev_err(dp->dev, "failed to initialize DP aux\n");
-		return ret;
-	}
-
-	/* Now that initialisation is complete, enable interrupts. */
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_EN, ZYNQMP_DP_INT_ALL);
-
-	return 0;
-}
-
-int zynqmp_dp_probe(struct zynqmp_dpsub *dpsub, struct drm_device *drm)
-{
-	struct platform_device *pdev = to_platform_device(dpsub->dev);
+	struct zynqmp_dpsub *dpsub;
 	struct zynqmp_dp *dp;
 	struct resource *res;
-	int ret;
+	struct device_node *port;
+	int irq, ret;
 
-	dp = drmm_kzalloc(drm, sizeof(*dp), GFP_KERNEL);
+	dp = devm_kzalloc(&pdev->dev, sizeof(*dp), GFP_KERNEL);
 	if (!dp)
 		return -ENOMEM;
 
-	dp->dev = &pdev->dev;
-	dp->dpsub = dpsub;
+	dp->dpms = DRM_MODE_DPMS_OFF;
 	dp->status = connector_status_disconnected;
-	dp->drm = drm;
-
-	INIT_DELAYED_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func);
-
-	dpsub->dp = dp;
+	dp->dev = &pdev->dev;
 
-	/* Acquire all resources (IOMEM, IRQ and PHYs). */
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dp");
 	dp->iomem = devm_ioremap_resource(dp->dev, res);
 	if (IS_ERR(dp->iomem))
 		return PTR_ERR(dp->iomem);
 
-	dp->irq = platform_get_irq(pdev, 0);
-	if (dp->irq < 0)
-		return dp->irq;
-
 	dp->reset = devm_reset_control_get(dp->dev, NULL);
-	if (IS_ERR(dp->reset)) {
-		if (PTR_ERR(dp->reset) != -EPROBE_DEFER)
-			dev_err(dp->dev, "failed to get reset: %ld\n",
-				PTR_ERR(dp->reset));
-		return PTR_ERR(dp->reset);
-	}
+	if (IS_ERR(dp->reset))
+		return dev_err_probe(dp->dev, PTR_ERR(dp->reset),
+			"failed to get reset: %ld\n", PTR_ERR(dp->reset));
 
 	ret = zynqmp_dp_reset(dp, false);
 	if (ret < 0)
 		return ret;
 
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_PHY_POWER_DOWN,
+			ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL);
+	zynqmp_dp_set(dp->iomem, ZYNQMP_DP_TX_PHY_CONFIG,
+		      ZYNQMP_DP_TX_PHY_CONFIG_ALL_RESET);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_FORCE_SCRAMBLER_RESET, 1);
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 0);
+
 	ret = zynqmp_dp_phy_probe(dp);
 	if (ret)
 		goto err_reset;
 
-	/* Initialize the hardware. */
-	zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN,
-			ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL);
-	zynqmp_dp_set(dp, ZYNQMP_DP_PHY_RESET, ZYNQMP_DP_PHY_RESET_ALL_RESET);
-	zynqmp_dp_write(dp, ZYNQMP_DP_FORCE_SCRAMBLER_RESET, 1);
-	zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 0);
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, 0xffffffff);
-
 	ret = zynqmp_dp_phy_init(dp);
 	if (ret)
-		goto err_reset;
+		goto error_phy;
+
+	dp->aux.name = "ZynqMP DP AUX";
+	dp->aux.dev = dp->dev;
+	dp->aux.transfer = zynqmp_dp_aux_transfer;
+	ret = drm_dp_aux_register(&dp->aux);
+	if (ret < 0) {
+		dev_err(dp->dev, "failed to initialize DP aux\n");
+		goto error;
+	}
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 1);
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto error;
+	}
 
-	/*
-	 * Now that the hardware is initialized and won't generate spurious
-	 * interrupts, request the IRQ.
-	 */
-	ret = devm_request_threaded_irq(dp->dev, dp->irq, NULL,
+	ret = devm_request_threaded_irq(dp->dev, irq, NULL,
 					zynqmp_dp_irq_handler, IRQF_ONESHOT,
 					dev_name(dp->dev), dp);
 	if (ret < 0)
-		goto err_phy_exit;
+		goto error;
+	dp->irq = irq;
+
+	dpsub = platform_get_drvdata(pdev);
+	dpsub->dp = dp;
+	dp->dpsub = dpsub;
+
+	for_each_child_of_node(pdev->dev.of_node, port) {
+		if (!port->name || of_node_cmp(port->name, "port"))
+			continue;
+
+		dpsub->external_crtc_attached = true;
+		break;
+	}
 
-	dev_dbg(dp->dev, "ZynqMP DisplayPort Tx probed with %u lanes\n",
+	dev_dbg(dp->dev,
+		"ZynqMP DisplayPort Tx driver probed with %u phy lanes\n",
 		dp->num_lanes);
 
 	return 0;
 
-err_phy_exit:
+error:
+	drm_dp_aux_unregister(&dp->aux);
+error_phy:
 	zynqmp_dp_phy_exit(dp);
 err_reset:
 	zynqmp_dp_reset(dp, true);
@@ -1722,19 +1991,16 @@
 	return ret;
 }
 
-void zynqmp_dp_remove(struct zynqmp_dpsub *dpsub)
+int zynqmp_dp_remove(struct platform_device *pdev)
 {
+	struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
 	struct zynqmp_dp *dp = dpsub->dp;
 
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, ZYNQMP_DP_INT_ALL);
-	disable_irq(dp->irq);
-
-	cancel_delayed_work_sync(&dp->hpd_work);
-	zynqmp_dp_aux_cleanup(dp);
-
-	zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 0);
-	zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, 0xffffffff);
-
+	zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 0);
+	drm_dp_aux_unregister(&dp->aux);
 	zynqmp_dp_phy_exit(dp);
 	zynqmp_dp_reset(dp, true);
+	dpsub->dp = NULL;
+
+	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_dp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_dp.h
@@ -12,16 +12,20 @@
 #ifndef _ZYNQMP_DP_H_
 #define _ZYNQMP_DP_H_
 
-struct drm_device;
-struct platform_device;
 struct zynqmp_dp;
-struct zynqmp_dpsub;
+struct drm_display_mode;
 
+int zynqmp_dp_set_color(struct zynqmp_dp *dp, const char *color);
 void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp);
 void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp);
+void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp,
+				       struct drm_display_mode *mode);
+void __maybe_unused zynqmp_dp_pm_suspend(struct zynqmp_dp *dp);
+void __maybe_unused zynqmp_dp_pm_resume(struct zynqmp_dp *dp);
+int zynqmp_dp_bind(struct device *dev, struct device *master, void *data);
+void zynqmp_dp_unbind(struct device *dev, struct device *master, void *data);
 
-int zynqmp_dp_drm_init(struct zynqmp_dpsub *dpsub);
-int zynqmp_dp_probe(struct zynqmp_dpsub *dpsub, struct drm_device *drm);
-void zynqmp_dp_remove(struct zynqmp_dpsub *dpsub);
+int zynqmp_dp_probe(struct platform_device *pdev);
+int zynqmp_dp_remove(struct platform_device *pdev);
 
 #endif /* _ZYNQMP_DP_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_dpsub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_dpsub.c
@@ -9,266 +9,174 @@
  * - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
  */
 
-#include <linux/clk.h>
-#include <linux/dma-mapping.h>
+#include <linux/component.h>
 #include <linux/module.h>
+#include <linux/of_platform.h>
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 
-#include <drm/drm_atomic_helper.h>
-#include <drm/drm_device.h>
-#include <drm/drm_drv.h>
-#include <drm/drm_fb_helper.h>
-#include <drm/drm_fourcc.h>
-#include <drm/drm_gem_cma_helper.h>
-#include <drm/drm_gem_framebuffer_helper.h>
-#include <drm/drm_managed.h>
-#include <drm/drm_mode_config.h>
-#include <drm/drm_probe_helper.h>
-#include <drm/drm_vblank.h>
+#include "xlnx_drv.h"
 
 #include "zynqmp_disp.h"
 #include "zynqmp_dp.h"
 #include "zynqmp_dpsub.h"
 
-/* -----------------------------------------------------------------------------
- * Dumb Buffer & Framebuffer Allocation
- */
-
-static int zynqmp_dpsub_dumb_create(struct drm_file *file_priv,
-				    struct drm_device *drm,
-				    struct drm_mode_create_dumb *args)
-{
-	struct zynqmp_dpsub *dpsub = to_zynqmp_dpsub(drm);
-	unsigned int pitch = DIV_ROUND_UP(args->width * args->bpp, 8);
-
-	/* Enforce the alignment constraints of the DMA engine. */
-	args->pitch = ALIGN(pitch, dpsub->dma_align);
-
-	return drm_gem_cma_dumb_create_internal(file_priv, drm, args);
-}
+#define DP_PCM_NAME_0 "zynqmp_dp_snd_pcm0"
+#define DP_PCM_NAME_1 "zynqmp_dp_snd_pcm1"
 
-static struct drm_framebuffer *
-zynqmp_dpsub_fb_create(struct drm_device *drm, struct drm_file *file_priv,
-		       const struct drm_mode_fb_cmd2 *mode_cmd)
+static int
+zynqmp_dpsub_bind(struct device *dev, struct device *master, void *data)
 {
-	struct zynqmp_dpsub *dpsub = to_zynqmp_dpsub(drm);
-	struct drm_mode_fb_cmd2 cmd = *mode_cmd;
-	unsigned int i;
-
-	/* Enforce the alignment constraints of the DMA engine. */
-	for (i = 0; i < ARRAY_SIZE(cmd.pitches); ++i)
-		cmd.pitches[i] = ALIGN(cmd.pitches[i], dpsub->dma_align);
-
-	return drm_gem_fb_create(drm, file_priv, &cmd);
-}
-
-static const struct drm_mode_config_funcs zynqmp_dpsub_mode_config_funcs = {
-	.fb_create		= zynqmp_dpsub_fb_create,
-	.atomic_check		= drm_atomic_helper_check,
-	.atomic_commit		= drm_atomic_helper_commit,
-};
-
-/* -----------------------------------------------------------------------------
- * DRM/KMS Driver
- */
-
-DEFINE_DRM_GEM_CMA_FOPS(zynqmp_dpsub_drm_fops);
-
-static const struct drm_driver zynqmp_dpsub_drm_driver = {
-	.driver_features		= DRIVER_MODESET | DRIVER_GEM |
-					  DRIVER_ATOMIC,
-
-	DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE(zynqmp_dpsub_dumb_create),
-
-	.fops				= &zynqmp_dpsub_drm_fops,
-
-	.name				= "zynqmp-dpsub",
-	.desc				= "Xilinx DisplayPort Subsystem Driver",
-	.date				= "20130509",
-	.major				= 1,
-	.minor				= 0,
-};
-
-static int zynqmp_dpsub_drm_init(struct zynqmp_dpsub *dpsub)
-{
-	struct drm_device *drm = &dpsub->drm;
 	int ret;
 
-	/* Initialize mode config, vblank and the KMS poll helper. */
-	ret = drmm_mode_config_init(drm);
-	if (ret < 0)
-		return ret;
-
-	drm->mode_config.funcs = &zynqmp_dpsub_mode_config_funcs;
-	drm->mode_config.min_width = 0;
-	drm->mode_config.min_height = 0;
-	drm->mode_config.max_width = ZYNQMP_DISP_MAX_WIDTH;
-	drm->mode_config.max_height = ZYNQMP_DISP_MAX_HEIGHT;
-
-	ret = drm_vblank_init(drm, 1);
+	ret = zynqmp_disp_bind(dev, master, data);
 	if (ret)
 		return ret;
 
-	drm_kms_helper_poll_init(drm);
-
-	/*
-	 * Initialize the DISP and DP components. This will creates planes,
-	 * CRTC, encoder and connector. The DISP should be initialized first as
-	 * the DP encoder needs the CRTC.
-	 */
-	ret = zynqmp_disp_drm_init(dpsub);
+	/* zynqmp_disp should bind first, so zynqmp_dp encoder can find crtc */
+	ret = zynqmp_dp_bind(dev, master, data);
 	if (ret)
-		goto err_poll_fini;
-
-	ret = zynqmp_dp_drm_init(dpsub);
-	if (ret)
-		goto err_poll_fini;
-
-	/* Reset all components and register the DRM device. */
-	drm_mode_config_reset(drm);
-
-	ret = drm_dev_register(drm, 0);
-	if (ret < 0)
-		goto err_poll_fini;
-
-	/* Initialize fbdev generic emulation. */
-	drm_fbdev_generic_setup(drm, 24);
+		return ret;
 
 	return 0;
-
-err_poll_fini:
-	drm_kms_helper_poll_fini(drm);
-	return ret;
-}
-
-/* -----------------------------------------------------------------------------
- * Power Management
- */
-
-static int __maybe_unused zynqmp_dpsub_suspend(struct device *dev)
-{
-	struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
-
-	return drm_mode_config_helper_suspend(&dpsub->drm);
 }
 
-static int __maybe_unused zynqmp_dpsub_resume(struct device *dev)
+static void
+zynqmp_dpsub_unbind(struct device *dev, struct device *master, void *data)
 {
-	struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
-
-	return drm_mode_config_helper_resume(&dpsub->drm);
+	zynqmp_dp_unbind(dev, master, data);
+	zynqmp_disp_unbind(dev, master, data);
 }
 
-static const struct dev_pm_ops zynqmp_dpsub_pm_ops = {
-	SET_SYSTEM_SLEEP_PM_OPS(zynqmp_dpsub_suspend, zynqmp_dpsub_resume)
+static const struct component_ops zynqmp_dpsub_component_ops = {
+	.bind	= zynqmp_dpsub_bind,
+	.unbind	= zynqmp_dpsub_unbind,
 };
 
-/* -----------------------------------------------------------------------------
- * Probe & Remove
- */
-
-static int zynqmp_dpsub_init_clocks(struct zynqmp_dpsub *dpsub)
-{
-	int ret;
-
-	dpsub->apb_clk = devm_clk_get(dpsub->dev, "dp_apb_clk");
-	if (IS_ERR(dpsub->apb_clk))
-		return PTR_ERR(dpsub->apb_clk);
-
-	ret = clk_prepare_enable(dpsub->apb_clk);
-	if (ret) {
-		dev_err(dpsub->dev, "failed to enable the APB clock\n");
-		return ret;
-	}
-
-	return 0;
-}
+static struct of_dev_auxdata zynqmp_dpsub_auxdata_lookup[] = {
+	OF_DEV_AUXDATA("xlnx,dp-snd-pcm0", 0, DP_PCM_NAME_0, NULL),
+	OF_DEV_AUXDATA("xlnx,dp-snd-pcm1", 0, DP_PCM_NAME_1, NULL),
+	{ /* end of table */ }
+};
 
 static int zynqmp_dpsub_probe(struct platform_device *pdev)
 {
 	struct zynqmp_dpsub *dpsub;
 	int ret;
 
-	/* Allocate private data. */
-	dpsub = devm_drm_dev_alloc(&pdev->dev, &zynqmp_dpsub_drm_driver,
-				   struct zynqmp_dpsub, drm);
-	if (IS_ERR(dpsub))
-		return PTR_ERR(dpsub);
+	dpsub = devm_kzalloc(&pdev->dev, sizeof(*dpsub), GFP_KERNEL);
+	if (!dpsub)
+		return -ENOMEM;
 
-	dpsub->dev = &pdev->dev;
+	/* Sub-driver will access dpsub from drvdata */
 	platform_set_drvdata(pdev, dpsub);
-
-	dma_set_mask(dpsub->dev, DMA_BIT_MASK(ZYNQMP_DISP_MAX_DMA_BIT));
-
-	/* Try the reserved memory. Proceed if there's none. */
-	of_reserved_mem_device_init(&pdev->dev);
-
-	ret = zynqmp_dpsub_init_clocks(dpsub);
-	if (ret < 0)
-		goto err_mem;
-
 	pm_runtime_enable(&pdev->dev);
 
 	/*
 	 * DP should be probed first so that the zynqmp_disp can set the output
 	 * format accordingly.
 	 */
-	ret = zynqmp_dp_probe(dpsub, &dpsub->drm);
+	ret = zynqmp_dp_probe(pdev);
 	if (ret)
 		goto err_pm;
 
-	ret = zynqmp_disp_probe(dpsub, &dpsub->drm);
+	ret = zynqmp_disp_probe(pdev);
 	if (ret)
 		goto err_dp;
 
-	ret = zynqmp_dpsub_drm_init(dpsub);
+	ret = component_add(&pdev->dev, &zynqmp_dpsub_component_ops);
 	if (ret)
 		goto err_disp;
 
+	/* Try the reserved memory. Proceed if there's none */
+	of_reserved_mem_device_init(&pdev->dev);
+
+	/* Populate the sound child nodes */
+	ret = of_platform_populate(pdev->dev.of_node, NULL,
+				   zynqmp_dpsub_auxdata_lookup, &pdev->dev);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to populate child nodes\n");
+		goto err_rmem;
+	}
+
+	if (!dpsub->external_crtc_attached) {
+		dpsub->master = xlnx_drm_pipeline_init(pdev);
+		if (IS_ERR(dpsub->master)) {
+			dev_err(&pdev->dev, "failed to initialize the drm pipeline\n");
+			goto err_populate;
+		}
+	}
+
 	dev_info(&pdev->dev, "ZynqMP DisplayPort Subsystem driver probed");
 
 	return 0;
 
+err_populate:
+	of_platform_depopulate(&pdev->dev);
+err_rmem:
+	of_reserved_mem_device_release(&pdev->dev);
+	component_del(&pdev->dev, &zynqmp_dpsub_component_ops);
 err_disp:
-	zynqmp_disp_remove(dpsub);
+	zynqmp_disp_remove(pdev);
 err_dp:
-	zynqmp_dp_remove(dpsub);
+	zynqmp_dp_remove(pdev);
 err_pm:
 	pm_runtime_disable(&pdev->dev);
-	clk_disable_unprepare(dpsub->apb_clk);
-err_mem:
-	of_reserved_mem_device_release(&pdev->dev);
 	return ret;
 }
 
 static int zynqmp_dpsub_remove(struct platform_device *pdev)
 {
 	struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
-	struct drm_device *drm = &dpsub->drm;
+	int err, ret = 0;
 
-	drm_dev_unregister(drm);
-	drm_atomic_helper_shutdown(drm);
-	drm_kms_helper_poll_fini(drm);
+	if (!dpsub->external_crtc_attached)
+		xlnx_drm_pipeline_exit(dpsub->master);
+	of_platform_depopulate(&pdev->dev);
+	of_reserved_mem_device_release(&pdev->dev);
+	component_del(&pdev->dev, &zynqmp_dpsub_component_ops);
 
-	zynqmp_disp_remove(dpsub);
-	zynqmp_dp_remove(dpsub);
+	err = zynqmp_disp_remove(pdev);
+	if (err)
+		ret = -EIO;
+
+	err = zynqmp_dp_remove(pdev);
+	if (err)
+		ret = -EIO;
 
 	pm_runtime_disable(&pdev->dev);
-	clk_disable_unprepare(dpsub->apb_clk);
-	of_reserved_mem_device_release(&pdev->dev);
+
+	return ret;
+}
+
+static int __maybe_unused zynqmp_dpsub_pm_suspend(struct device *dev)
+{
+	struct platform_device *pdev =
+		container_of(dev, struct platform_device, dev);
+	struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
+
+	zynqmp_dp_pm_suspend(dpsub->dp);
 
 	return 0;
 }
 
-static void zynqmp_dpsub_shutdown(struct platform_device *pdev)
+static int __maybe_unused zynqmp_dpsub_pm_resume(struct device *dev)
 {
+	struct platform_device *pdev =
+		container_of(dev, struct platform_device, dev);
 	struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
 
-	drm_atomic_helper_shutdown(&dpsub->drm);
+	zynqmp_dp_pm_resume(dpsub->dp);
+
+	return 0;
 }
 
+static const struct dev_pm_ops zynqmp_dpsub_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(zynqmp_dpsub_pm_suspend,
+				zynqmp_dpsub_pm_resume)
+};
+
 static const struct of_device_id zynqmp_dpsub_of_match[] = {
 	{ .compatible = "xlnx,zynqmp-dpsub-1.7", },
 	{ /* end of table */ },
@@ -278,9 +186,8 @@
 static struct platform_driver zynqmp_dpsub_driver = {
 	.probe			= zynqmp_dpsub_probe,
 	.remove			= zynqmp_dpsub_remove,
-	.shutdown		= zynqmp_dpsub_shutdown,
 	.driver			= {
-		.name		= "zynqmp-dpsub",
+		.name		= "zynqmp-display",
 		.pm		= &zynqmp_dpsub_pm_ops,
 		.of_match_table	= zynqmp_dpsub_of_match,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/xlnx/zynqmp_dpsub.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/xlnx/zynqmp_dpsub.h
@@ -12,43 +12,11 @@
 #ifndef _ZYNQMP_DPSUB_H_
 #define _ZYNQMP_DPSUB_H_
 
-struct clk;
-struct device;
-struct drm_device;
-struct zynqmp_disp;
-struct zynqmp_dp;
-
-enum zynqmp_dpsub_format {
-	ZYNQMP_DPSUB_FORMAT_RGB,
-	ZYNQMP_DPSUB_FORMAT_YCRCB444,
-	ZYNQMP_DPSUB_FORMAT_YCRCB422,
-	ZYNQMP_DPSUB_FORMAT_YONLY,
-};
-
-/**
- * struct zynqmp_dpsub - ZynqMP DisplayPort Subsystem
- * @drm: The DRM/KMS device
- * @dev: The physical device
- * @apb_clk: The APB clock
- * @disp: The display controller
- * @dp: The DisplayPort controller
- * @dma_align: DMA alignment constraint (must be a power of 2)
- */
 struct zynqmp_dpsub {
-	struct drm_device drm;
-	struct device *dev;
-
-	struct clk *apb_clk;
-
-	struct zynqmp_disp *disp;
 	struct zynqmp_dp *dp;
-
-	unsigned int dma_align;
+	struct zynqmp_disp *disp;
+	bool external_crtc_attached;
+	struct platform_device *master;
 };
 
-static inline struct zynqmp_dpsub *to_zynqmp_dpsub(struct drm_device *drm)
-{
-	return container_of(drm, struct zynqmp_dpsub, drm);
-}
-
 #endif /* _ZYNQMP_DPSUB_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/Kconfig
@@ -0,0 +1,8 @@
+config DRM_ZOCL
+	tristate "Xilinx Zynq OpenCL"
+	depends on DRM
+	select DRM_KMS_HELPER
+	select DRM_KMS_CMA_HELPER
+	select DRM_GEM_CMA_HELPER
+	help
+	  Xilinx Zynq OpenCL Manager
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/LICENSE
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/LICENSE
@@ -0,0 +1,481 @@
+All "zocl" Linux kernel driver code authored by Xilinx is released
+under the terms of either Apache License, Version 2.0, or alternatively
+under the terms of the GNU General Public License version 2:
+
+Copyright (C) 2016-2020 Xilinx, Inc. All rights reserved.
+
+This software is licensed under the terms of the GNU General Public
+License version 2, as published by the Free Software Foundation, and
+may be copied, distributed, and modified under those terms.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You may use the Linux kernel driver code according to either of these
+licenses as is most appropriate for your project on a case-by-case basis.
+
+The full text for both licenses is included for reference below.
+
+
+
+                                 Apache License
+                           Version 2.0, January 2004
+                        http://www.apache.org/licenses/
+
+   TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
+
+   1. Definitions.
+
+      "License" shall mean the terms and conditions for use, reproduction,
+      and distribution as defined by Sections 1 through 9 of this document.
+
+      "Licensor" shall mean the copyright owner or entity authorized by
+      the copyright owner that is granting the License.
+
+      "Legal Entity" shall mean the union of the acting entity and all
+      other entities that control, are controlled by, or are under common
+      control with that entity. For the purposes of this definition,
+      "control" means (i) the power, direct or indirect, to cause the
+      direction or management of such entity, whether by contract or
+      otherwise, or (ii) ownership of fifty percent (50%) or more of the
+      outstanding shares, or (iii) beneficial ownership of such entity.
+
+      "You" (or "Your") shall mean an individual or Legal Entity
+      exercising permissions granted by this License.
+
+      "Source" form shall mean the preferred form for making modifications,
+      including but not limited to software source code, documentation
+      source, and configuration files.
+
+      "Object" form shall mean any form resulting from mechanical
+      transformation or translation of a Source form, including but
+      not limited to compiled object code, generated documentation,
+      and conversions to other media types.
+
+      "Work" shall mean the work of authorship, whether in Source or
+      Object form, made available under the License, as indicated by a
+      copyright notice that is included in or attached to the work
+      (an example is provided in the Appendix below).
+
+      "Derivative Works" shall mean any work, whether in Source or Object
+      form, that is based on (or derived from) the Work and for which the
+      editorial revisions, annotations, elaborations, or other modifications
+      represent, as a whole, an original work of authorship. For the purposes
+      of this License, Derivative Works shall not include works that remain
+      separable from, or merely link (or bind by name) to the interfaces of,
+      the Work and Derivative Works thereof.
+
+      "Contribution" shall mean any work of authorship, including
+      the original version of the Work and any modifications or additions
+      to that Work or Derivative Works thereof, that is intentionally
+      submitted to Licensor for inclusion in the Work by the copyright owner
+      or by an individual or Legal Entity authorized to submit on behalf of
+      the copyright owner. For the purposes of this definition, "submitted"
+      means any form of electronic, verbal, or written communication sent
+      to the Licensor or its representatives, including but not limited to
+      communication on electronic mailing lists, source code control systems,
+      and issue tracking systems that are managed by, or on behalf of, the
+      Licensor for the purpose of discussing and improving the Work, but
+      excluding communication that is conspicuously marked or otherwise
+      designated in writing by the copyright owner as "Not a Contribution."
+
+      "Contributor" shall mean Licensor and any individual or Legal Entity
+      on behalf of whom a Contribution has been received by Licensor and
+      subsequently incorporated within the Work.
+
+   2. Grant of Copyright License. Subject to the terms and conditions of
+      this License, each Contributor hereby grants to You a perpetual,
+      worldwide, non-exclusive, no-charge, royalty-free, irrevocable
+      copyright license to reproduce, prepare Derivative Works of,
+      publicly display, publicly perform, sublicense, and distribute the
+      Work and such Derivative Works in Source or Object form.
+
+   3. Grant of Patent License. Subject to the terms and conditions of
+      this License, each Contributor hereby grants to You a perpetual,
+      worldwide, non-exclusive, no-charge, royalty-free, irrevocable
+      (except as stated in this section) patent license to make, have made,
+      use, offer to sell, sell, import, and otherwise transfer the Work,
+      where such license applies only to those patent claims licensable
+      by such Contributor that are necessarily infringed by their
+      Contribution(s) alone or by combination of their Contribution(s)
+      with the Work to which such Contribution(s) was submitted. If You
+      institute patent litigation against any entity (including a
+      cross-claim or counterclaim in a lawsuit) alleging that the Work
+      or a Contribution incorporated within the Work constitutes direct
+      or contributory patent infringement, then any patent licenses
+      granted to You under this License for that Work shall terminate
+      as of the date such litigation is filed.
+
+   4. Redistribution. You may reproduce and distribute copies of the
+      Work or Derivative Works thereof in any medium, with or without
+      modifications, and in Source or Object form, provided that You
+      meet the following conditions:
+
+      (a) You must give any other recipients of the Work or
+          Derivative Works a copy of this License; and
+
+      (b) You must cause any modified files to carry prominent notices
+          stating that You changed the files; and
+
+      (c) You must retain, in the Source form of any Derivative Works
+          that You distribute, all copyright, patent, trademark, and
+          attribution notices from the Source form of the Work,
+          excluding those notices that do not pertain to any part of
+          the Derivative Works; and
+
+      (d) If the Work includes a "NOTICE" text file as part of its
+          distribution, then any Derivative Works that You distribute must
+          include a readable copy of the attribution notices contained
+          within such NOTICE file, excluding those notices that do not
+          pertain to any part of the Derivative Works, in at least one
+          of the following places: within a NOTICE text file distributed
+          as part of the Derivative Works; within the Source form or
+          documentation, if provided along with the Derivative Works; or,
+          within a display generated by the Derivative Works, if and
+          wherever such third-party notices normally appear. The contents
+          of the NOTICE file are for informational purposes only and
+          do not modify the License. You may add Your own attribution
+          notices within Derivative Works that You distribute, alongside
+          or as an addendum to the NOTICE text from the Work, provided
+          that such additional attribution notices cannot be construed
+          as modifying the License.
+
+      You may add Your own copyright statement to Your modifications and
+      may provide additional or different license terms and conditions
+      for use, reproduction, or distribution of Your modifications, or
+      for any such Derivative Works as a whole, provided Your use,
+      reproduction, and distribution of the Work otherwise complies with
+      the conditions stated in this License.
+
+   5. Submission of Contributions. Unless You explicitly state otherwise,
+      any Contribution intentionally submitted for inclusion in the Work
+      by You to the Licensor shall be under the terms and conditions of
+      this License, without any additional terms or conditions.
+      Notwithstanding the above, nothing herein shall supersede or modify
+      the terms of any separate license agreement you may have executed
+      with Licensor regarding such Contributions.
+
+   6. Trademarks. This License does not grant permission to use the trade
+      names, trademarks, service marks, or product names of the Licensor,
+      except as required for reasonable and customary use in describing the
+      origin of the Work and reproducing the content of the NOTICE file.
+
+   7. Disclaimer of Warranty. Unless required by applicable law or
+      agreed to in writing, Licensor provides the Work (and each
+      Contributor provides its Contributions) on an "AS IS" BASIS,
+      WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or
+      implied, including, without limitation, any warranties or conditions
+      of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A
+      PARTICULAR PURPOSE. You are solely responsible for determining the
+      appropriateness of using or redistributing the Work and assume any
+      risks associated with Your exercise of permissions under this License.
+
+   8. Limitation of Liability. In no event and under no legal theory,
+      whether in tort (including negligence), contract, or otherwise,
+      unless required by applicable law (such as deliberate and grossly
+      negligent acts) or agreed to in writing, shall any Contributor be
+      liable to You for damages, including any direct, indirect, special,
+      incidental, or consequential damages of any character arising as a
+      result of this License or out of the use or inability to use the
+      Work (including but not limited to damages for loss of goodwill,
+      work stoppage, computer failure or malfunction, or any and all
+      other commercial damages or losses), even if such Contributor
+      has been advised of the possibility of such damages.
+
+   9. Accepting Warranty or Additional Liability. While redistributing
+      the Work or Derivative Works thereof, You may choose to offer,
+      and charge a fee for, acceptance of support, warranty, indemnity,
+      or other liability obligations and/or rights consistent with this
+      License. However, in accepting such obligations, You may act only
+      on Your own behalf and on Your sole responsibility, not on behalf
+      of any other Contributor, and only if You agree to indemnify,
+      defend, and hold each Contributor harmless for any liability
+      incurred by, or claims asserted against, such Contributor by reason
+      of your accepting any such warranty or additional liability.
+
+   END OF TERMS AND CONDITIONS
+
+---------------------------------------------------------------------------
+
+ GNU GENERAL PUBLIC LICENSE
+                       Version 2, June 1991
+
+ Copyright (C) 1989, 1991 Free Software Foundation, Inc.,
+ 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+                            Preamble
+
+  The licenses for most software are designed to take away your
+freedom to share and change it.  By contrast, the GNU General Public
+License is intended to guarantee your freedom to share and change free
+software--to make sure the software is free for all its users.  This
+General Public License applies to most of the Free Software
+Foundation's software and to any other program whose authors commit to
+using it.  (Some other Free Software Foundation software is covered by
+the GNU Lesser General Public License instead.)  You can apply it to
+your programs, too.
+
+  When we speak of free software, we are referring to freedom, not
+price.  Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+this service if you wish), that you receive source code or can get it
+if you want it, that you can change the software or use pieces of it
+in new free programs; and that you know you can do these things.
+
+  To protect your rights, we need to make restrictions that forbid
+anyone to deny you these rights or to ask you to surrender the rights.
+These restrictions translate to certain responsibilities for you if you
+distribute copies of the software, or if you modify it.
+
+  For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must give the recipients all the rights that
+you have.  You must make sure that they, too, receive or can get the
+source code.  And you must show them these terms so they know their
+rights.
+
+  We protect your rights with two steps: (1) copyright the software, and
+(2) offer you this license which gives you legal permission to copy,
+distribute and/or modify the software.
+
+  Also, for each author's protection and ours, we want to make certain
+that everyone understands that there is no warranty for this free
+software.  If the software is modified by someone else and passed on, we
+want its recipients to know that what they have is not the original, so
+that any problems introduced by others will not reflect on the original
+authors' reputations.
+
+  Finally, any free program is threatened constantly by software
+patents.  We wish to avoid the danger that redistributors of a free
+program will individually obtain patent licenses, in effect making the
+program proprietary.  To prevent this, we have made it clear that any
+patent must be licensed for everyone's free use or not licensed at all.
+
+  The precise terms and conditions for copying, distribution and
+modification follow.
+
+                    GNU GENERAL PUBLIC LICENSE
+   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
+
+  0. This License applies to any program or other work which contains
+a notice placed by the copyright holder saying it may be distributed
+under the terms of this General Public License.  The "Program", below,
+refers to any such program or work, and a "work based on the Program"
+means either the Program or any derivative work under copyright law:
+that is to say, a work containing the Program or a portion of it,
+either verbatim or with modifications and/or translated into another
+language.  (Hereinafter, translation is included without limitation in
+the term "modification".)  Each licensee is addressed as "you".
+
+Activities other than copying, distribution and modification are not
+covered by this License; they are outside its scope.  The act of
+running the Program is not restricted, and the output from the Program
+is covered only if its contents constitute a work based on the
+Program (independent of having been made by running the Program).
+Whether that is true depends on what the Program does.
+
+  1. You may copy and distribute verbatim copies of the Program's
+source code as you receive it, in any medium, provided that you
+conspicuously and appropriately publish on each copy an appropriate
+copyright notice and disclaimer of warranty; keep intact all the
+notices that refer to this License and to the absence of any warranty;
+and give any other recipients of the Program a copy of this License
+along with the Program.
+
+You may charge a fee for the physical act of transferring a copy, and
+you may at your option offer warranty protection in exchange for a fee.
+
+  2. You may modify your copy or copies of the Program or any portion
+of it, thus forming a work based on the Program, and copy and
+distribute such modifications or work under the terms of Section 1
+above, provided that you also meet all of these conditions:
+
+    a) You must cause the modified files to carry prominent notices
+    stating that you changed the files and the date of any change.
+
+    b) You must cause any work that you distribute or publish, that in
+    whole or in part contains or is derived from the Program or any
+    part thereof, to be licensed as a whole at no charge to all third
+    parties under the terms of this License.
+
+    c) If the modified program normally reads commands interactively
+    when run, you must cause it, when started running for such
+    interactive use in the most ordinary way, to print or display an
+    announcement including an appropriate copyright notice and a
+    notice that there is no warranty (or else, saying that you provide
+    a warranty) and that users may redistribute the program under
+    these conditions, and telling the user how to view a copy of this
+    License.  (Exception: if the Program itself is interactive but
+    does not normally print such an announcement, your work based on
+    the Program is not required to print an announcement.)
+
+These requirements apply to the modified work as a whole.  If
+identifiable sections of that work are not derived from the Program,
+and can be reasonably considered independent and separate works in
+themselves, then this License, and its terms, do not apply to those
+sections when you distribute them as separate works.  But when you
+distribute the same sections as part of a whole which is a work based
+on the Program, the distribution of the whole must be on the terms of
+this License, whose permissions for other licensees extend to the
+entire whole, and thus to each and every part regardless of who wrote it.
+
+Thus, it is not the intent of this section to claim rights or contest
+your rights to work written entirely by you; rather, the intent is to
+exercise the right to control the distribution of derivative or
+collective works based on the Program.
+
+In addition, mere aggregation of another work not based on the Program
+with the Program (or with a work based on the Program) on a volume of
+a storage or distribution medium does not bring the other work under
+the scope of this License.
+
+  3. You may copy and distribute the Program (or a work based on it,
+under Section 2) in object code or executable form under the terms of
+Sections 1 and 2 above provided that you also do one of the following:
+
+    a) Accompany it with the complete corresponding machine-readable
+    source code, which must be distributed under the terms of Sections
+    1 and 2 above on a medium customarily used for software interchange; or,
+
+    b) Accompany it with a written offer, valid for at least three
+    years, to give any third party, for a charge no more than your
+    cost of physically performing source distribution, a complete
+    machine-readable copy of the corresponding source code, to be
+    distributed under the terms of Sections 1 and 2 above on a medium
+    customarily used for software interchange; or,
+
+    c) Accompany it with the information you received as to the offer
+    to distribute corresponding source code.  (This alternative is
+    allowed only for noncommercial distribution and only if you
+    received the program in object code or executable form with such
+    an offer, in accord with Subsection b above.)
+
+The source code for a work means the preferred form of the work for
+making modifications to it.  For an executable work, complete source
+code means all the source code for all modules it contains, plus any
+associated interface definition files, plus the scripts used to
+control compilation and installation of the executable.  However, as a
+special exception, the source code distributed need not include
+anything that is normally distributed (in either source or binary
+form) with the major components (compiler, kernel, and so on) of the
+operating system on which the executable runs, unless that component
+itself accompanies the executable.
+
+If distribution of executable or object code is made by offering
+access to copy from a designated place, then offering equivalent
+access to copy the source code from the same place counts as
+distribution of the source code, even though third parties are not
+compelled to copy the source along with the object code.
+
+  4. You may not copy, modify, sublicense, or distribute the Program
+except as expressly provided under this License.  Any attempt
+otherwise to copy, modify, sublicense or distribute the Program is
+void, and will automatically terminate your rights under this License.
+However, parties who have received copies, or rights, from you under
+this License will not have their licenses terminated so long as such
+parties remain in full compliance.
+
+  5. You are not required to accept this License, since you have not
+signed it.  However, nothing else grants you permission to modify or
+distribute the Program or its derivative works.  These actions are
+prohibited by law if you do not accept this License.  Therefore, by
+modifying or distributing the Program (or any work based on the
+Program), you indicate your acceptance of this License to do so, and
+all its terms and conditions for copying, distributing or modifying
+the Program or works based on it.
+
+  6. Each time you redistribute the Program (or any work based on the
+Program), the recipient automatically receives a license from the
+original licensor to copy, distribute or modify the Program subject to
+these terms and conditions.  You may not impose any further
+restrictions on the recipients' exercise of the rights granted herein.
+You are not responsible for enforcing compliance by third parties to
+this License.
+
+  7. If, as a consequence of a court judgment or allegation of patent
+infringement or for any other reason (not limited to patent issues),
+conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License.  If you cannot
+distribute so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you
+may not distribute the Program at all.  For example, if a patent
+license would not permit royalty-free redistribution of the Program by
+all those who receive copies directly or indirectly through you, then
+the only way you could satisfy both it and this License would be to
+refrain entirely from distribution of the Program.
+
+If any portion of this section is held invalid or unenforceable under
+any particular circumstance, the balance of the section is intended to
+apply and the section as a whole is intended to apply in other
+circumstances.
+
+It is not the purpose of this section to induce you to infringe any
+patents or other property right claims or to contest validity of any
+such claims; this section has the sole purpose of protecting the
+integrity of the free software distribution system, which is
+implemented by public license practices.  Many people have made
+generous contributions to the wide range of software distributed
+through that system in reliance on consistent application of that
+system; it is up to the author/donor to decide if he or she is willing
+to distribute software through any other system and a licensee cannot
+impose that choice.
+
+This section is intended to make thoroughly clear what is believed to
+be a consequence of the rest of this License.
+
+  8. If the distribution and/or use of the Program is restricted in
+certain countries either by patents or by copyrighted interfaces, the
+original copyright holder who places the Program under this License
+may add an explicit geographical distribution limitation excluding
+those countries, so that distribution is permitted only in or among
+countries not thus excluded.  In such case, this License incorporates
+the limitation as if written in the body of this License.
+
+  9. The Free Software Foundation may publish revised and/or new versions
+of the General Public License from time to time.  Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+Each version is given a distinguishing version number.  If the Program
+specifies a version number of this License which applies to it and "any
+later version", you have the option of following the terms and conditions
+either of that version or of any later version published by the Free
+Software Foundation.  If the Program does not specify a version number of
+this License, you may choose any version ever published by the Free Software
+Foundation.
+
+  10. If you wish to incorporate parts of the Program into other free
+programs whose distribution conditions are different, write to the author
+to ask for permission.  For software which is copyrighted by the Free
+Software Foundation, write to the Free Software Foundation; we sometimes
+make exceptions for this.  Our decision will be guided by the two goals
+of preserving the free status of all derivatives of our free software and
+of promoting the sharing and reuse of software generally.
+
+                            NO WARRANTY
+
+  11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
+FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.  EXCEPT WHEN
+OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
+PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
+OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRE RISK AS
+TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.  SHOULD THE
+PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
+REPAIR OR CORRECTION.
+
+  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
+REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
+INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
+OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
+TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
+YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
+PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGES.
+
+                     END OF TERMS AND CONDITIONS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/Makefile
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: GPL-2.0
+
+export XRT_DRIVER_VERSION := 2.13.479
+ccflags-y := -I$(srctree)/$(src)/include -I$(src)/../../include -I$(src)/../../../include -I$(src)/../../../common/drv/include -DXRT_HASH="\"$(GIT_HASH)\"" -DXRT_HASH_DATE="\"$(GIT_HASH_DATE)\"" -DXRT_BRANCH="\"$(GIT_BRANCH)\"" -DXRT_MODIFIED_FILES="\"$(GIT_MODIFIED_FILES)\"" -DXRT_DATE="\"$(DATE_NOW)\"" -DXRT_DRIVER_VERSION="\"$(XRT_DRIVER_VERSION)\""
+
+common_dir = common
+drv_common-y   := $(common_dir)/kds_core.o \
+                  $(common_dir)/cu_hls.o \
+                  $(common_dir)/fast_adapter.o \
+                  $(common_dir)/xrt_cu.o \
+                  $(common_dir)/xrt_xclbin.o
+
+zocl-y := \
+	$(drv_common-y) \
+	zocl_sysfs.o \
+	zocl_ioctl.o \
+	zocl_ert.o \
+	zocl_watchdog.o \
+	zocl_drv.o \
+	zocl_bo.o \
+	zocl_dma.o \
+	zocl_cu.o \
+	zocl_mailbox.o \
+	zocl_ov_sysfs.o \
+	zocl_ospi_versal.o \
+	zocl_xclbin.o \
+	zocl_sk.o \
+	zocl_kds.o \
+	cu.o \
+	cu_scu.o \
+	scu.o \
+	zocl_error.o \
+	zocl_aie.o \
+	zocl_ctrl_ert.o \
+	zocl_xgq.o \
+	zocl_lib.o \
+	zocl_cu_xgq.o \
+	zocl_rpu_channel.o \
+	zocl_csr_intc.o \
+	zocl_xgq_intc.o
+
+obj-$(CONFIG_DRM_ZOCL) += zocl.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0 OR Apache-2.0
+#
+# Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+#
+# Authors:
+#
+# This file is dual-licensed; you may select either the GNU General Public
+# License version 2 or Apache License, Version 2.0.
+
+clean:
+	rm -f *.o *~ core .depend .*.cmd *.ko *.mod.c
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/cu_hls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/cu_hls.c
@@ -0,0 +1,548 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx HLS CU
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/delay.h>
+#include "xrt_cu.h"
+#include "xgq_cmd_ert.h"
+
+/* Control register bits and special behavior if any.
+ * Bit 0: ap_start(Read/Set). Clear by CU when ap_ready assert.
+ * Bit 1: ap_done(Read only). Clear on read.
+ * Bit 2: ap_idle(Read only).
+ * Bit 3: ap_ready(Read only). Self clear after clear ap_start.
+ * Bit 4: ap_continue(Read/Set). Self clear.
+ * Bit 5-7: Not support yet
+ * Bit 8: ap_sw_reset. Clear when reset is done.
+ */
+#define CTRL		0x0
+/* Global interrupt enable: Set bit 0 to enable. Clear it to disable */
+#define GIE		0x4
+/* Interrupt Enable Register
+ * Bit 0: ap_done. 0 - disable; 1 - enable.
+ * Bit 1: ap_ready. 0 - disable; 1 - enable.
+ */
+#define IER		0x8
+/* Interrupt Status Register
+ * Bit 0: ap_done(Toggle on set).
+ * Bit 1: ap_done(Toggle on set).
+ *   Toggle on set - Write 1 would flip the bit. Write 0 has no change.
+ */
+#define ISR		0xC
+#define ARGS		0x10
+
+extern int kds_echo;
+
+struct xrt_cu_hls {
+	void __iomem		*vaddr;
+	int			 max_credits;
+	int			 credits;
+	int			 run_cnts;
+	bool			 ctrl_chain;
+	bool			 sw_reset;
+	spinlock_t		 cu_lock;
+	u32			 done;
+	u32			 ready;
+	struct list_head	 submitted;
+	struct list_head	 completed;
+};
+
+static inline u32 cu_read32(struct xrt_cu_hls *cu, u32 reg)
+{
+	u32 ret;
+
+	ret = ioread32(cu->vaddr + reg);
+	return ret;
+}
+
+static inline void cu_write32(struct xrt_cu_hls *cu, u32 reg, u32 val)
+{
+	iowrite32(val, cu->vaddr + reg);
+}
+
+static inline void cu_move_to_complete(struct xrt_cu_hls *cu, int status)
+{
+	struct kds_command *xcmd = NULL;
+
+	if (unlikely(list_empty(&cu->submitted)))
+		return;
+
+	xcmd = list_first_entry(&cu->submitted, struct kds_command, list);
+	xcmd->status = status;
+	cu->run_cnts--;
+	list_move_tail(&xcmd->list, &cu->completed);
+}
+
+static int cu_hls_alloc_credit(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	return (cu_hls->credits) ? cu_hls->credits-- : 0;
+}
+
+static void cu_hls_free_credit(void *core, u32 count)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	cu_hls->credits += count;
+	if (cu_hls->credits > cu_hls->max_credits)
+		cu_hls->credits = cu_hls->max_credits;
+}
+
+static int cu_hls_peek_credit(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	return cu_hls->credits;
+}
+
+static void cu_hls_xgq_start(struct xrt_cu_hls *cu_hls, u32 *data)
+{
+	struct xgq_cmd_start_cuidx *cmd = (struct xgq_cmd_start_cuidx *)data;
+	u32 num_reg = 0;
+	u32 i = 0;
+
+	num_reg = (cmd->hdr.count - (sizeof(struct xgq_cmd_start_cuidx)
+				     - sizeof(cmd->hdr) - sizeof(cmd->data)))/sizeof(u32);
+	for (i = 0; i < num_reg; ++i) {
+		cu_write32(cu_hls, ARGS + i * 4, cmd->data[i]);
+	}
+}
+
+static void cu_hls_xgq_start_kv(struct xrt_cu_hls *cu_hls, u32 *data)
+{
+	struct xgq_cmd_start_cuidx_kv *cmd = (struct xgq_cmd_start_cuidx_kv *)data;
+	u32 num_reg = 0;
+	u32 i = 0;
+
+	num_reg = (cmd->hdr.count - (sizeof(struct xgq_cmd_start_cuidx_kv)
+				     - sizeof(cmd->hdr) - sizeof(cmd->data)))/sizeof(u32);
+	/* data is a {offset : value} pairs list
+	 * cmd->data[i] -> offset
+	 * cmd->data[i+1] -> value
+	 */
+	for (i = 0; i < num_reg; i += 2)
+		cu_write32(cu_hls, cmd->data[i], cmd->data[i + 1]);
+}
+
+static int cu_hls_configure(void *core, u32 *data, size_t sz, int type)
+{
+	struct xrt_cu_hls *cu_hls = core;
+	struct xgq_cmd_sq_hdr *hdr;
+	size_t num_reg = 0;
+	u32 i = 0;
+
+	if (kds_echo)
+		return 0;
+
+	num_reg = sz / sizeof(u32);
+	switch (type) {
+	case REGMAP:
+		/* Write register map, starting at base_addr + 0x10 (byte) */
+		for (i = 0; i < num_reg; ++i)
+			cu_write32(cu_hls, ARGS + i * 4, data[i]);
+		break;
+	case KEY_VAL:
+		/* Use {offset, value} pairs to configure CU
+		 * data[i]: register offset
+		 * data[i + 1]: value
+		 */
+		for (i = 0; i < num_reg; i += 2)
+			cu_write32(cu_hls, data[i], data[i + 1]);
+		break;
+	case XGQ_CMD:
+		hdr = (struct xgq_cmd_sq_hdr *)data;
+		if (hdr->opcode == XGQ_CMD_OP_START_CUIDX)
+			cu_hls_xgq_start(cu_hls, data);
+		else if (hdr->opcode == XGQ_CMD_OP_START_CUIDX_KV)
+			cu_hls_xgq_start_kv(cu_hls, data);
+		else
+			return -EINVAL;
+		break;
+	}
+	return 0;
+}
+
+static void cu_hls_start(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	cu_hls->run_cnts++;
+
+	if (kds_echo)
+		return;
+
+	cu_write32(cu_hls, CTRL, CU_AP_START);
+}
+
+/*
+ * In ap_ctrl_hs protocol, HLS CU can run one task at a time. Once CU is
+ * started, software should wait for CU done before configure/start CU again.
+ * The done bit is clear on read. So, the software just need to read control
+ * register.
+ */
+static inline void
+cu_hls_ctrl_hs_check(struct xrt_cu_hls *cu_hls, struct xcu_status *status, bool force)
+{
+	u32 ctrl_reg = 0;
+	u32 done_reg = 0;
+	u32 ready_reg = 0;
+
+	/* Avoid access CU register unless we do have running commands.
+	 * This has a huge impact on performance.
+	 */
+	if (!force && !cu_hls->run_cnts)
+		return;
+
+	ctrl_reg = cu_read32(cu_hls, CTRL);
+	/* ap_ready and ap_done would assert at the same cycle */
+	if (ctrl_reg & CU_AP_DONE) {
+		done_reg  = 1;
+		ready_reg = 1;
+		cu_move_to_complete(cu_hls, KDS_COMPLETED);
+	}
+
+	status->num_done  = done_reg;
+	status->num_ready = ready_reg;
+	status->new_status = ctrl_reg;
+}
+
+/*
+ * In ap_ctrl_check protocol, HLS CU can setup next task before CU is done.
+ * After CU started, the start bit will keep high until CU assert ap_ready.
+ * Once a CU is ready, it means CU is ready to be configured.
+ * If CU is done, it means the previous task is completed. But the CU would
+ * stall until ap_continue bit is set.
+ */
+static inline void
+cu_hls_ctrl_chain_check(struct xrt_cu_hls *cu_hls, struct xcu_status *status, bool force)
+{
+	u32 ctrl_reg = 0;
+	u32 done_reg = 0;
+	u32 ready_reg = 0;
+	u32 used_credit;
+	unsigned long flags;
+
+	used_credit = cu_hls->max_credits - cu_hls->credits;
+
+	/* Access CU when there are unsed credits or running commands
+	 * This has a huge impact on performance.
+	 */
+	if (!force && !used_credit && !cu_hls->run_cnts)
+		return;
+
+	/* HLS ap_ctrl_chain reqiured software to set ap_continue before
+	 * clear interrupt. Otherwise, the clear would failed.
+	 * So, we have to make ap_continue and clear interrupt as atomic.
+	 */
+	spin_lock_irqsave(&cu_hls->cu_lock, flags);
+	done_reg  = cu_hls->done;
+	ready_reg = cu_hls->ready;
+	cu_hls->done = 0;
+	cu_hls->ready = 0;
+
+	ctrl_reg = cu_read32(cu_hls, CTRL);
+
+	/* if there is submitted tasks, then check if ap_start bit is clear
+	 * See comments in cu_hls_start().
+	 */
+	if (!ready_reg && used_credit && !(ctrl_reg & CU_AP_START))
+		ready_reg = 1;
+
+	if (ctrl_reg & CU_AP_DONE) {
+		done_reg += 1;
+		cu_write32(cu_hls, CTRL, CU_AP_CONTINUE);
+		cu_move_to_complete(cu_hls, KDS_COMPLETED);
+	}
+	spin_unlock_irqrestore(&cu_hls->cu_lock, flags);
+
+	status->num_done  = done_reg;
+	status->num_ready = ready_reg;
+	status->new_status = ctrl_reg;
+}
+
+static void cu_hls_check(void *core, struct xcu_status *status, bool force)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	if (kds_echo) {
+		status->num_done = 1;
+		status->num_ready = 1;
+		status->new_status = CU_AP_IDLE;
+		cu_move_to_complete(cu_hls, KDS_COMPLETED);
+		return;
+	}
+
+	if (cu_hls->ctrl_chain)
+		cu_hls_ctrl_chain_check(cu_hls, status, force);
+	else
+		cu_hls_ctrl_hs_check(cu_hls, status, force);
+}
+
+static void cu_hls_enable_intr(void *core, u32 intr_type)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	cu_write32(cu_hls, GIE, 0x1);
+	cu_write32(cu_hls, IER, intr_type);
+}
+
+static void cu_hls_disable_intr(void *core, u32 intr_type)
+{
+	struct xrt_cu_hls *cu_hls = core;
+	u32 orig = cu_read32(cu_hls, IER);
+	/* if bit 0 of intr_type is set, it means disable ap_done,
+	 * same to bit 1 for ap_ready.
+	 */
+	u32 new = orig & (~intr_type);
+
+	cu_write32(cu_hls, GIE, 0x0);
+	cu_write32(cu_hls, IER, new);
+}
+
+static u32 cu_hls_clear_intr(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	/* Clear all interrupts of the CU
+	 *
+	 * HLS style kernel has Interrupt Status Register at offset 0x0C
+	 * It has two interrupt bits, bit[0] is ap_done, bit[1] is ap_ready.
+	 *
+	 * The ap_done interrupt means this CU is complete.
+	 * The ap_ready interrupt means all inputs have been read.
+	 */
+	if (cu_hls->max_credits == 1) {
+		u32 isr;
+		u32 ctrl_reg = 0;
+		unsigned long flags;
+
+		/*
+		 * The old HLS adapter.
+		 *
+		 * The Interrupt Status Register is Toggle On Write
+		 * RegData = RegData ^ WriteData
+		 *
+		 * So, the reliable way to clear this register is read
+		 * then write the same value back.
+		 *
+		 * Do not write 1 to this register.  If, somehow, the
+		 * status register is 0, write 1 to this register will
+		 * trigger interrupt.
+		 */
+		isr = cu_read32(cu_hls, ISR);
+
+		/* See comment in cu_hls_ctrl_chain_check() */
+		if (cu_hls->ctrl_chain) {
+			spin_lock_irqsave(&cu_hls->cu_lock, flags);
+			if (isr & CU_INTR_READY)
+				cu_hls->ready++;
+
+			if (isr & CU_INTR_DONE) {
+				ctrl_reg = cu_read32(cu_hls, CTRL);
+				if (ctrl_reg & CU_AP_DONE) {
+					cu_hls->done++;
+					cu_move_to_complete(cu_hls, KDS_COMPLETED);
+					cu_write32(cu_hls, CTRL, CU_AP_CONTINUE);
+				}
+			}
+			spin_unlock_irqrestore(&cu_hls->cu_lock, flags);
+		}
+
+		cu_write32(cu_hls, ISR, isr);
+		return isr;
+	}
+
+	/*
+	 * The new HLS adapter with queue.
+	 *
+	 * The Interrupt Status Register is Clear on Read.
+	 *
+	 * For debug purpose, This register is toggle on write.
+	 * Write 1 to this register will trigger interrupt.
+	 */
+	return cu_read32(cu_hls, ISR);
+}
+
+static void cu_hls_reset(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+
+	cu_write32(cu_hls, CTRL, CU_AP_SW_RESET);
+}
+
+static bool cu_hls_reset_done(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+	u32 ctrl_reg;
+
+	ctrl_reg = cu_read32(cu_hls, CTRL);
+	if (ctrl_reg & CU_AP_SW_RESET)
+		return false;
+
+	return true;
+}
+
+static int cu_hls_submit_config(void *core, struct kds_command *xcmd)
+{
+	struct xrt_cu_hls *cu_hls = core;
+	int ret = 0;
+
+	ret = cu_hls_configure(core, (u32 *)xcmd->info, xcmd->isize, xcmd->payload_type);
+	if (ret)
+		return ret;
+
+	list_move_tail(&xcmd->list, &cu_hls->submitted);
+	return ret;
+}
+
+static struct kds_command *cu_hls_get_complete(void *core)
+{
+	struct xrt_cu_hls *cu_hls = core;
+	struct kds_command *xcmd = NULL;
+
+	if (list_empty(&cu_hls->completed))
+		return NULL;
+
+	xcmd = list_first_entry(&cu_hls->completed, struct kds_command, list);
+	list_del_init(&xcmd->list);
+
+	return xcmd;
+}
+
+static int cu_hls_abort(void *core, void *cond,
+			bool (*match)(struct kds_command *xcmd, void *cond))
+{
+	struct xrt_cu_hls *cu_hls = core;
+	struct kds_command *xcmd = NULL;
+	struct kds_command *next = NULL;
+	int ret = -EBUSY;
+
+	if (cu_hls->sw_reset) {
+		int time = 10 * 1000 * 1000; /* 10 second */
+		cu_hls_reset(core);
+
+		do {
+			usleep_range(1000, 1500);
+			time -= 1000;
+			if (cu_hls_reset_done(core))
+				break;
+		} while (time > 0);
+
+		/* Reset is done, CU is still functional */
+		if (time >= 0) {
+			cu_hls->credits = cu_hls->max_credits;
+			ret = 0;
+		}
+	}
+
+	list_for_each_entry_safe(xcmd, next, &cu_hls->submitted, list) {
+		if (!match(xcmd, cond))
+			continue;
+
+		xcmd->status = KDS_TIMEOUT;
+		list_move_tail(&xcmd->list, &cu_hls->completed);
+	}
+
+	return ret;
+}
+
+static struct xcu_funcs xrt_cu_hls_funcs = {
+	.alloc_credit	= cu_hls_alloc_credit,
+	.free_credit	= cu_hls_free_credit,
+	.peek_credit	= cu_hls_peek_credit,
+	.configure	= cu_hls_configure,
+	.start		= cu_hls_start,
+	.check		= cu_hls_check,
+	.enable_intr	= cu_hls_enable_intr,
+	.disable_intr	= cu_hls_disable_intr,
+	.clear_intr	= cu_hls_clear_intr,
+	.reset		= cu_hls_reset,
+	.reset_done	= cu_hls_reset_done,
+	.submit_config  = cu_hls_submit_config,
+	.get_complete   = cu_hls_get_complete,
+	.abort		= cu_hls_abort,
+};
+
+int xrt_cu_hls_init(struct xrt_cu *xcu)
+{
+	struct xrt_cu_hls *core;
+	struct resource *res;
+	size_t size;
+	int err = 0;
+
+	core = kzalloc(sizeof(struct xrt_cu_hls), GFP_KERNEL);
+	if (!core) {
+		err = -ENOMEM;
+		goto err;
+	}
+
+	/* map CU register */
+	/* TODO: add comment why uses res[0] */
+	res = xcu->res[0];
+	size = res->end - res->start + 1;
+	core->vaddr = ioremap_nocache(res->start, size);
+	if (!core->vaddr) {
+		err = -ENOMEM;
+		xcu_err(xcu, "Map CU register failed");
+		goto err;
+	}
+
+	core->max_credits = 1;
+	core->credits = core->max_credits;
+	core->run_cnts = 0;
+	core->ctrl_chain = (xcu->info.protocol == CTRL_CHAIN)? true : false;
+	spin_lock_init(&core->cu_lock);
+	core->done = 0;
+	core->ready = 0;
+	core->sw_reset = xcu->info.sw_reset;
+	INIT_LIST_HEAD(&core->submitted);
+	INIT_LIST_HEAD(&core->completed);
+
+	xcu->core = core;
+	xcu->funcs = &xrt_cu_hls_funcs;
+
+	xcu->busy_threshold = -1;
+	xcu->interval_min = 2;
+	xcu->interval_max = 5;
+
+	/* No control and interrupt registers in ap_ctrl_none protocol.
+	 * In this case, return here for creating CU sub-dev. No need to setup
+	 * CU thread and queues.
+	 */
+	if (xcu->info.protocol == CTRL_NONE)
+		return  0;
+
+	xcu->status = cu_read32(core, CTRL);
+	err = xrt_cu_init(xcu);
+	if (err)
+		return err;
+
+	return 0;
+
+err:
+	kfree(core);
+	return err;
+}
+
+void xrt_cu_hls_fini(struct xrt_cu *xcu)
+{
+	struct xrt_cu_hls *core = xcu->core;
+
+	if (xcu->info.protocol != CTRL_NONE)
+		xrt_cu_fini(xcu);
+
+	if (xcu->core) {
+		if (core->vaddr)
+			iounmap(core->vaddr);
+		kfree(xcu->core);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/fast_adapter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/fast_adapter.c
@@ -0,0 +1,355 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx CU with fast adapter.
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "xrt_cu.h"
+
+/* Fast Adapter register layout
+ * nextDescriptorAddr_MSW: Most significant word of paddr of descriptor
+ * nextDescriptorAddr_LSW: Least significant word of paddr of descriptor
+ * interruptStatus: Interrupt status register
+ * Status: Flagging error conditions, e.g. FIFO overrun
+ * taskCount: Task Counter that tracks how many tasks have been processed
+ * currentDescriptorAddr: Address of descriptor currently being processed by CU
+ * fifoDepth: Current adapter FIFO depth
+ */
+#define MSWR		0x0
+#define LSWR		0x4
+#define ISR		0x8
+#define IER		0xC
+#define SR		0x10
+#define TCR		0x14
+#define CDAR		0x18
+#define FDR		0x1C
+
+#define ENABLE  1
+#define DISABLE 0
+
+extern int kds_echo;
+
+static inline u32 cu_read32(struct xrt_cu_fa *cu, u32 reg)
+{
+	u32 ret;
+
+	ret = ioread32(cu->vaddr + reg);
+	return ret;
+}
+
+static inline void cu_write32(struct xrt_cu_fa *cu, u32 reg, u32 val)
+{
+	iowrite32(val, cu->vaddr + reg);
+}
+
+static inline void cu_move_to_complete(struct xrt_cu_fa *cu, int status)
+{
+	struct kds_command *xcmd = NULL;
+
+	if (unlikely(list_empty(&cu->submitted)))
+		return;
+
+	xcmd = list_first_entry(&cu->submitted, struct kds_command, list);
+	xcmd->status = status;
+
+	list_move_tail(&xcmd->list, &cu->completed);
+}
+
+static int cu_fa_alloc_credit(void *core)
+{
+	struct xrt_cu_fa *cu_fa = core;
+
+	return (cu_fa->credits) ? cu_fa->credits-- : 0;
+}
+
+static void cu_fa_free_credit(void *core, u32 count)
+{
+	struct xrt_cu_fa *cu_fa = core;
+	int max_credits;
+
+	cu_fa->credits += count;
+
+	max_credits = (cu_fa->num_slots < cu_fa->max_credits)?
+		       cu_fa->num_slots : cu_fa->max_credits;
+
+	if (cu_fa->credits > max_credits)
+		cu_fa->credits = max_credits;
+}
+
+static int cu_fa_peek_credit(void *core)
+{
+	struct xrt_cu_fa *cu_fa = core;
+
+	return cu_fa->credits;
+}
+
+static int cu_fa_configure(void *core, u32 *data, size_t sz, int type)
+{
+	struct xrt_cu_fa *cu_fa = core;
+	u32 *slot = cu_fa->cmdmem + cu_fa->head_slot;
+
+	/* in case cmdmem is not update properly */
+	WARN_ON(!cu_fa->cmdmem);
+
+	if (kds_echo || !cu_fa->cmdmem)
+		return 0;
+
+	/* move commands to device quickly is the key of performance */
+	memcpy(&slot[1], &data[1], sz - 4);
+
+	/* Update status of descriptor */
+	wmb();
+	slot[0] = data[0];
+	return 0;
+}
+
+static void cu_fa_start(void *core)
+{
+	struct xrt_cu_fa *cu_fa = core;
+	u32 desc_msw = cu_fa->paddr >> 32;
+	u32 desc_lsw = (u32)cu_fa->paddr;
+
+	cu_fa->run_cnts++;
+
+	if (kds_echo || !cu_fa->cmdmem)
+		return;
+
+	/* The MSW of descriptor is fixed */
+	if (desc_msw != cu_fa->desc_msw) {
+		cu_write32(cu_fa, MSWR, desc_msw);
+		cu_fa->desc_msw = desc_msw;
+	}
+
+	/* Write LSW would kick off CU */
+	cu_write32(cu_fa, LSWR, desc_lsw + cu_fa->head_slot);
+
+	/* move to next descriptor slot */
+	cu_fa->head_slot += cu_fa->slot_sz;
+	if (cu_fa->head_slot == cu_fa->slot_sz * cu_fa->num_slots)
+		cu_fa->head_slot = 0;
+}
+
+static void cu_fa_check(void *core, struct xcu_status *status, bool force)
+{
+	struct xrt_cu_fa *cu_fa = core;
+	u32 task_count = 0;
+	u32 done = 0;
+	int i = 0;
+
+	if (kds_echo || !cu_fa->cmdmem) {
+		cu_fa->run_cnts--;
+		status->num_done = 1;
+		status->num_ready = 1;
+		return;
+	}
+
+	/* Avoid access CU register unless we do have running commands.
+	 * This has a huge impact on performance.
+	 */
+	if (!force && !cu_fa->run_cnts)
+		return;
+
+	cu_fa->check_count++;
+	task_count = cu_read32(cu_fa, TCR);
+	/* If taskCount register overflow once, below calculate is still correct.
+	 * Only when the register overflow more than once, this is wrong.
+	 * But this should never be the case.
+	 */
+	done = task_count - cu_fa->task_cnt;
+	cu_fa->task_cnt = task_count;
+
+	cu_fa->run_cnts -= done;
+	for (i = 0; i < done; i++)
+		cu_move_to_complete(cu_fa, KDS_COMPLETED);
+
+	status->num_done  = done;
+	status->num_ready = done;
+}
+
+static void cu_fa_enable_intr(void *core, u32 intr_type)
+{
+	struct xrt_cu_fa *cu_fa = core;
+
+	cu_write32(cu_fa, IER, ENABLE);
+	return;
+}
+
+static void cu_fa_disable_intr(void *core, u32 intr_type)
+{
+	struct xrt_cu_fa *cu_fa = core;
+
+	cu_write32(cu_fa, IER, DISABLE);
+	return;
+}
+
+static u32 cu_fa_clear_intr(void *core)
+{
+	struct xrt_cu_fa *cu_fa = core;
+
+	return cu_read32(cu_fa, ISR);
+}
+
+static void cu_fa_reset(void *core)
+{
+	/* Fast adapter doesn't define software reset */
+	return;
+}
+
+static bool cu_fa_reset_done(void *core)
+{
+	return true;
+}
+
+static int cu_fa_submit_config(void *core, struct kds_command *xcmd)
+{
+	struct xrt_cu_fa *cu_fa = core;
+	int ret = 0;
+
+	ret = cu_fa_configure(core, (u32 *)xcmd->info, xcmd->isize, xcmd->payload_type);
+	if (ret)
+		return ret;
+
+	list_move_tail(&xcmd->list, &cu_fa->submitted);
+	return ret;
+}
+
+static struct kds_command *cu_fa_get_complete(void *core)
+{
+	struct xrt_cu_fa *cu_fa = core;
+	struct kds_command *xcmd = NULL;
+
+	if (list_empty(&cu_fa->completed))
+		return NULL;
+
+	xcmd = list_first_entry(&cu_fa->completed, struct kds_command, list);
+	list_del_init(&xcmd->list);
+
+	return xcmd;
+}
+
+static int cu_fa_abort(void *core, void *cond,
+		       bool (*match)(struct kds_command *xcmd, void *cond))
+{
+	struct xrt_cu_fa *cu_fa = core;
+	struct kds_command *xcmd = NULL;
+	struct kds_command *next = NULL;
+	int ret = -EBUSY;
+
+	list_for_each_entry_safe(xcmd, next, &cu_fa->submitted, list) {
+		if (!match(xcmd, cond))
+			continue;
+
+		xcmd->status = KDS_TIMEOUT;
+		list_move_tail(&xcmd->list, &cu_fa->completed);
+	}
+
+	return ret;
+}
+
+static struct xcu_funcs xrt_cu_fa_funcs = {
+	.alloc_credit	= cu_fa_alloc_credit,
+	.free_credit	= cu_fa_free_credit,
+	.peek_credit	= cu_fa_peek_credit,
+	.configure	= cu_fa_configure,
+	.start		= cu_fa_start,
+	.check		= cu_fa_check,
+	.enable_intr	= cu_fa_enable_intr,
+	.disable_intr	= cu_fa_disable_intr,
+	.clear_intr	= cu_fa_clear_intr,
+	.reset		= cu_fa_reset,
+	.reset_done	= cu_fa_reset_done,
+	.submit_config  = cu_fa_submit_config,
+	.get_complete   = cu_fa_get_complete,
+	.abort		= cu_fa_abort,
+};
+
+int xrt_cu_fa_init(struct xrt_cu *xcu)
+{
+	struct xrt_cu_fa *core;
+	struct resource *res;
+	size_t size;
+	int err = 0;
+
+	core = kzalloc(sizeof(struct xrt_cu_fa), GFP_KERNEL);
+	if (!core) {
+		err = -ENOMEM;
+		goto err;
+	}
+
+	/* map CU register */
+	res = xcu->res[0];
+	size = res->end - res->start + 1;
+	core->vaddr = ioremap_nocache(res->start, size);
+	if (!core->vaddr) {
+		err = -ENOMEM;
+		xcu_err(xcu, "Map CU register failed");
+		goto err;
+	}
+
+	/* TODO:
+	 * Looks like it would read wrong value from a just downloaded
+	 * fast adapter. This is a hardware bug.
+	 * We could write 0x0 to Status Register (read only) to workaround
+	 * this issue.
+	 * But, read any register doesn't always work.
+	 * Please do not remove below line until it is fixed on hardware.
+	 */
+	cu_write32(core, SR, 0x0);
+	core->max_credits = cu_read32(core, FDR);
+	core->task_cnt = cu_read32(core, TCR);
+	core->desc_msw = cu_read32(core, MSWR);
+	xcu_info(xcu, "Fast adapter FIFO depth %d", core->max_credits);
+	xcu_info(xcu, "Fast adapter init taskCount 0x%x", core->task_cnt);
+	core->credits = core->max_credits;
+	core->run_cnts = 0;
+	INIT_LIST_HEAD(&core->submitted);
+	INIT_LIST_HEAD(&core->completed);
+
+	/* TODO:
+	 * Maybe in the future, we could initial all of the CU resource at this
+	 * place. Now, this is just to note that below variables will initial
+	 * when xclbin download finished and kds get update.
+	 *   core->cmdmem
+	 *   core->paddr
+	 *   core->head_slot
+	 *   core->num_slots
+	 */
+
+	xcu->core = core;
+	xcu->funcs = &xrt_cu_fa_funcs;
+	/* Not sure what is the best initial value.
+	 * But below parameters are configurable to user. No worry.
+	 */
+	xcu->busy_threshold = core->max_credits / 2;
+	xcu->interval_min = 2;
+	xcu->interval_max = 5;
+
+	err = xrt_cu_init(xcu);
+	if (err)
+		return err;
+
+	return 0;
+
+err:
+	kfree(core);
+	return err;
+}
+
+void xrt_cu_fa_fini(struct xrt_cu *xcu)
+{
+	struct xrt_cu_fa *core = xcu->core;
+
+	xrt_cu_fini(xcu);
+
+	if (xcu->core) {
+		if (core->vaddr)
+			iounmap(core->vaddr);
+		kfree(xcu->core);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/cu_xgq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/cu_xgq.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx CU XGQ header
+ *
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: chienwei@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _CU_XGQ_H
+#define _CU_XGQ_H
+
+#include "xrt_cu.h"
+
+int xrt_cu_xgq_init(struct xrt_cu *xcu, int slow_path);
+void xrt_cu_xgq_fini(struct xrt_cu *xcu);
+
+#endif // _CU_XGQ_H
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/kds_client.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/kds_client.h
@@ -0,0 +1,102 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2021-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_CLIENT_H
+#define _KDS_CLIENT_H
+
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/pid.h>
+#include <linux/device.h>
+#include <linux/uuid.h>
+
+#include "xrt_cu.h"
+#include "kds_stat.h"
+
+#define EV_ABORT	0x1
+
+/* Multiple xclbin context can be active under a single client.
+ * Client should maintain all the active XCLBIN.
+ */
+struct kds_client_ctx {
+	struct list_head          link;
+	void			 *xclbin_id;
+	u32			  slot_idx;
+	u32			  num_ctx;
+	u32			  num_scu_ctx;
+	u32			  virt_cu_ref;
+};
+
+/**
+ * struct kds_client: Manage user client
+ * Whenever user applciation open the device, a client would be created.
+ * A client will keep alive util application close the device or being killed.
+ * The client could open multiple contexts to access compute resources.
+ *
+ * @link: Client is added to list in KDS scheduler
+ * @dev:  Device
+ * @pid:  Client process ID
+ * @lock: Mutex to protext context related members
+ * @xclbin_id: UUID of xclbin cache
+ * @num_ctx: Number of context that opened
+ * @num_scu_ctx: Number of soft kernel context that opened
+ * @virt_cu_ref: Reference count of virtual CU
+ * @cu_bitmap: bitmap of opening CU
+ * @scu_bitmap: bitmap of opening SCU
+ * @waitq: Wait queue for poll client
+ * @event: Events to notify user client
+ */
+struct kds_client {
+	struct list_head	  link;
+	struct device	         *dev;
+	struct pid	         *pid;
+	struct mutex		  lock;
+
+	/* TODO: xocl not suppot multiple xclbin context yet. */
+	struct kds_client_ctx    *ctx;
+	struct list_head          ctx_list;
+
+	struct list_head          graph_list;
+	spinlock_t                graph_list_lock;
+	u32                       aie_ctx;
+
+	DECLARE_BITMAP(cu_bitmap, MAX_CUS);
+	DECLARE_BITMAP(scu_bitmap, MAX_CUS);
+	/* Per client statistics. Use percpu variable for two reasons
+	 * 1. no lock is need while modifying these counters
+	 * 2. do not need to worry about cache false share
+	 */
+	struct client_stats __percpu *stats;
+
+	struct list_head	  ev_entry;
+	int			  ev_type;
+
+	/*
+	 * Below are modified when the other thread is completing commands.
+	 * In order to prevent false sharing, they need to be in different
+	 * cache lines.
+	 */
+	wait_queue_head_t	  waitq ____cacheline_aligned_in_smp;
+	atomic_t		  event;
+};
+
+/* Macros to operates client statistics */
+#define client_stat_read(client, field) \
+	stat_read((client)->stats, field)
+
+#define client_stat_inc(client, field) \
+	this_stat_inc((client)->stats, field)
+
+#define client_stat_dec(client, field) \
+	this_stat_dec((client)->stats, field)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/kds_command.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/kds_command.h
@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2020-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_COMMAND_H
+#define _KDS_COMMAND_H
+
+#include "xgq_cmd_ert.h"
+/* Userspace command format */
+#include "ert.h"
+
+#define REGMAP 0
+#define KEY_VAL 1
+#define XGQ_CMD 2
+
+enum kds_opcode {
+	OP_NONE = 0,
+	OP_CONFIG,
+	OP_START,
+	OP_ABORT,
+	OP_CONFIG_SK, /* TODO: There is a plan to remove softkernel config and unconfig command */
+	OP_START_SK,
+	OP_CLK_CALIB,
+	OP_VALIDATE,
+	OP_GET_STAT,
+};
+
+/* KDS_NEW:		Command is validated
+ * KDS_QUEUED:		Command is sent to pending queue
+ * KDS_RUNNING:		Command is sent to hardware (CU/ERT)
+ * KDS_COMPLETED:	Command is completed
+ * KDS_ERROR:		Command is error out
+ * KDS_ABORT:		Command is abort
+ * KDS_TIMEOUT:		Command is timeout
+ */
+enum kds_status {
+	KDS_NEW = 0,
+	KDS_QUEUED,
+	KDS_RUNNING,
+	KDS_COMPLETED,
+	KDS_ERROR,
+	KDS_ABORT,
+	KDS_TIMEOUT,
+	KDS_STAT_MAX,
+};
+
+struct kds_command;
+
+struct kds_cmd_ops {
+	void (*notify_host)(struct kds_command *xcmd, int status);
+	void (*free)(struct kds_command *xcmd);
+};
+
+struct in_kernel_cb {
+	void (*func)(unsigned long cb_data, int err);
+	void *data;
+};
+
+/* Default cu index of a command */
+#define NO_INDEX -1
+
+/**
+ * struct kds_command: KDS command struct
+ * @client: the client that the command belongs to
+ * @type:   type of the command. Use this to determin controller
+ */
+struct kds_command {
+	struct kds_client	*client;
+	int			 status;
+	u32			 rcode;
+	int			 cu_idx;
+	u32			 type;
+	u32			 opcode;
+	struct list_head	 list;
+	u32			 payload_alloc;
+	u32			 payload_type;
+	void			*info;
+	size_t			 isize;
+	void                    *response;
+	size_t                   response_size;
+	struct kds_cmd_ops	 cb;
+	void			*priv;
+
+	unsigned int		 tick;
+	u32			 timestamp_enabled;
+	u64			 timestamp[KDS_STAT_MAX];
+
+	/* TODO: may rethink if we should have cu bit mask here
+	 * or move it to info.
+	 * Since NO all types of command have cu_mask
+	 */
+	u32			 cu_mask[4];
+	u32			 num_mask;
+	u64			 start;
+
+	/* execbuf is used to update the header
+	 * of execbuf when notifying host
+	 */
+	u32			*execbuf;
+	u32			*u_execbuf;
+	void			*gem_obj;
+	u32			 exec_bo_handle;
+	/* to notify inkernel exec completion */
+	struct in_kernel_cb	*inkern_cb;
+};
+
+void set_xcmd_timestamp(struct kds_command *xcmd, enum kds_status s);
+
+/* execbuf command related funtions */
+void cfg_ecmd2xcmd(struct ert_configure_cmd *ecmd,
+		   struct kds_command *xcmd);
+void start_krnl_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd);
+void start_skrnl_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd);
+void start_krnl_kv_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			     struct kds_command *xcmd);
+void start_fa_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			struct kds_command *xcmd);
+void abort_ecmd2xcmd(struct ert_abort_cmd *ecmd,
+		     struct kds_command *xcmd);
+int cu_mask_to_cu_idx(struct kds_command *xcmd, uint8_t *cus);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/kds_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/kds_core.h
@@ -0,0 +1,211 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_CORE_H
+#define _KDS_CORE_H
+
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/pid.h>
+#include <linux/device.h>
+#include <linux/uuid.h>
+#include <linux/kthread.h>
+
+#include "kds_client.h"
+#include "kds_command.h"
+#include "xrt_cu.h"
+#include "kds_stat.h"
+#include "xclbin.h"
+
+#define kds_info(client, fmt, args...)			\
+	dev_info(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+#define kds_err(client, fmt, args...)			\
+	dev_err(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+#define kds_warn(client, fmt, args...)			\
+	dev_warn(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+#define kds_dbg(client, fmt, args...)			\
+	dev_dbg(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+
+enum kds_type {
+	KDS_CU		= 0,
+	KDS_SCU,
+	KDS_ERT,
+	KDS_MAX_TYPE, // always the last one
+};
+
+/* Context properties */
+#define	CU_CTX_PROP_MASK	0x0F
+#define	CU_CTX_SHARED		0x00
+#define	CU_CTX_EXCLUSIVE	0x01
+
+/* Virtual CU index
+ * This is useful when there is no need to open a context on hardware CU,
+ * but still need to lockdown the xclbin.
+ */
+#define	CU_CTX_VIRT_CU		0xffffffff
+struct kds_ctx_info {
+	u32		  cu_domain;
+	u32		  cu_idx;
+	u32		  flags;
+	void		 *curr_ctx; // Holds the current context ptr for kds
+};
+
+/* TODO: PS kernel is very different with FPGA kernel.
+ * Let's see if we can unify them later.
+ */
+struct kds_scu_mgmt {
+	struct xrt_cu		 *xcus[MAX_CUS];
+	struct mutex		  lock;
+	int			  num_cus;
+	u32			  status[MAX_CUS];
+	char			  name[MAX_CUS][32];
+	u32			  cu_refs[MAX_CUS];
+	struct cu_stats __percpu *cu_stats;
+};
+
+/* the MSB of cu_refs is used for exclusive flag */
+#define CU_EXCLU_MASK		0x80000000
+struct kds_cu_mgmt {
+	struct xrt_cu		 *xcus[MAX_CUS];
+	struct mutex		  lock;
+	int			  num_cus;
+	int			  num_cdma;
+	u32			  cu_intr[MAX_CUS];
+	u32			  cu_refs[MAX_CUS];
+	struct cu_stats __percpu *cu_stats;
+	int			  rw_shared;
+};
+
+#define cu_stat_read(cu_mgmt, field) \
+	stat_read((cu_mgmt)->cu_stats, field)
+
+#define cu_stat_write(cu_mgmt, field, val) \
+	stat_write((cu_mgmt)->cu_stats, field, val)
+
+#define cu_stat_inc(cu_mgmt, field) \
+	this_stat_inc((cu_mgmt)->cu_stats, field)
+
+#define cu_stat_dec(cu_mgmt, field) \
+	this_stat_dec((cu_mgmt)->cu_stats, field)
+
+/* ERT core */
+struct kds_ert {
+	u32			slot_size;
+	void (* submit)(struct kds_ert *ert, struct kds_command *xcmd);
+	void (* abort)(struct kds_ert *ert, struct kds_client *client, int cu_idx);
+	bool (* abort_done)(struct kds_ert *ert, struct kds_client *client, int cu_idx);
+	bool (* abort_sync)(struct kds_ert *ert, struct kds_client *client, int cu_idx);
+};
+
+/* Fast adapter memory info */
+#define FA_MEM_MAX_SIZE 128 * 1024
+struct cmdmem_info {
+	/* This is use for free bo, do not use it in shared code */
+	void		       *bo;
+	u64			bar_paddr;
+	u64			dev_paddr;
+	void __iomem		*vaddr;
+	u32			size;
+};
+
+/**
+ * struct kds_sched: KDS scheduler manage CUs and client list.
+ *		     There should be only one KDS per device.
+ *
+ * @list_head: Client list
+ * @num_client: Number of clients
+ * @lock: Mutex to protect client list
+ * @cu_mgmt: hardware CUs management data structure
+ * @ert: remote scheduler
+ * @ert_disable: remote scheduler is disabled or not
+ * @xgq_enable: remote scheduler supports XGQ
+ * @cu_intr_cap: capbility of CU interrupt support
+ * @cu_intr: CU or ERT interrupt. 1 for CU, 0 for ERT.
+ * @anon_client: driver own kds client used with driver generated command
+ * @polling_thread: poll CUs when ERT is disabled
+ */
+#define KDS_SYSFS_SETTING_BIT	(1 << 31)
+#define KDS_SET_SYSFS_BIT(val)	(val | KDS_SYSFS_SETTING_BIT)
+#define KDS_SYSFS_SETTING(val)	(val & KDS_SYSFS_SETTING_BIT)
+#define KDS_SETTING(val)	(val & ~KDS_SYSFS_SETTING_BIT)
+struct kds_sched {
+	struct list_head	clients;
+	int			num_client;
+	struct mutex		lock;
+	bool			bad_state;
+	struct kds_cu_mgmt	cu_mgmt;
+	struct kds_scu_mgmt	scu_mgmt;
+	struct kds_ert	       *ert;
+	bool			xgq_enable;
+	u32			cu_intr_cap;
+	struct cmdmem_info	cmdmem;
+	struct completion	comp;
+	struct kds_client      *anon_client;
+
+	/* Settings */
+	bool			ini_disable;
+	bool			ert_disable;
+	u32			cu_intr;
+
+	/* KDS polling thread */
+	struct task_struct     *polling_thread;
+	struct list_head	alive_cus; /* alive CU list */
+	wait_queue_head_t	wait_queue;
+	int			polling_start;
+	int			polling_stop;
+	u32			interval;
+};
+
+int kds_init_sched(struct kds_sched *kds);
+int kds_init_ert(struct kds_sched *kds, struct kds_ert *ert);
+int kds_init_client(struct kds_sched *kds, struct kds_client *client);
+void kds_fini_sched(struct kds_sched *kds);
+int kds_fini_ert(struct kds_sched *kds);
+void kds_fini_client(struct kds_sched *kds, struct kds_client *client);
+void kds_reset(struct kds_sched *kds);
+int kds_cfg_update(struct kds_sched *kds);
+void kds_cus_irq_enable(struct kds_sched *kds, bool enable);
+int is_bad_state(struct kds_sched *kds);
+u32 kds_live_clients(struct kds_sched *kds, pid_t **plist);
+u32 kds_live_clients_nolock(struct kds_sched *kds, pid_t **plist);
+int kds_add_cu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_del_cu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_add_scu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_del_scu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_get_cu_total(struct kds_sched *kds);
+u32 kds_get_cu_addr(struct kds_sched *kds, int idx);
+u32 kds_get_cu_proto(struct kds_sched *kds, int idx);
+int kds_get_max_regmap_size(struct kds_sched *kds);
+int kds_add_context(struct kds_sched *kds, struct kds_client *client,
+		    struct kds_ctx_info *info);
+int kds_del_context(struct kds_sched *kds, struct kds_client *client,
+		    struct kds_ctx_info *info);
+int kds_open_ucu(struct kds_sched *kds, struct kds_client *client, u32 cu_idx);
+int kds_map_cu_addr(struct kds_sched *kds, struct kds_client *client,
+		    int idx, unsigned long size, u32 *addrp);
+int kds_add_command(struct kds_sched *kds, struct kds_command *xcmd);
+/* Use this function in xclbin download flow for config commands */
+int kds_submit_cmd_and_wait(struct kds_sched *kds, struct kds_command *xcmd);
+
+struct kds_command *kds_alloc_command(struct kds_client *client, u32 size);
+
+void kds_free_command(struct kds_command *xcmd);
+int kds_ip_layout2cu_info(struct ip_layout *ip_layout, struct xrt_cu_info cu_info[], int num_info);
+int kds_ip_layout2scu_info(struct ip_layout *ip_layout, struct xrt_cu_info cu_info[], int num_info);
+
+/* sysfs */
+int store_kds_echo(struct kds_sched *kds, const char *buf, size_t count,
+		   int *echo);
+ssize_t show_kds_stat(struct kds_sched *kds, char *buf);
+ssize_t show_kds_custat_raw(struct kds_sched *kds, char *buf);
+ssize_t show_kds_scustat_raw(struct kds_sched *kds, char *buf);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/kds_stat.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/kds_stat.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_STAT_H
+#define _KDS_STAT_H
+
+#include <linux/percpu-defs.h>
+
+/* TODO: Using MAX_CUS in this header file is not ideal.
+ * This file eventually should be very independent.
+ * Let's remove all MAX_CUS from this file once we have chance.
+ */
+#ifndef MAX_CUS
+#define MAX_CUS 128
+#endif
+
+/* This header file defines statistics struct and macros to operates them.
+ * Percpu variable are used for performance concerns.
+ */
+
+struct client_stats {
+	/* Per CU counter that counts when a command is submitted to CU */
+	unsigned long		s_cnt[MAX_CUS];
+	/* Per CU counter that counts when a command is completed or error */
+	unsigned long		c_cnt[MAX_CUS];
+	/* Per soft CU counter that counts when a command is submitted to SCU */
+	unsigned long		scu_s_cnt[MAX_CUS];
+	/* Per soft CU counter that counts when a command is completed or error */
+	unsigned long		scu_c_cnt[MAX_CUS];
+};
+
+struct cu_stats {
+	u64		  usage[MAX_CUS];
+};
+
+/*
+ * Macros to operates on percpu statistics:
+ * this_cpu_* are operations with implied preemption/interrupt protection.
+ */
+#define this_stat_get(statp, field) \
+	this_cpu_read((statp)->field)
+
+#define this_stat_set(statp, field, val) \
+	this_cpu_write((statp)->field, val)
+
+#define this_stat_inc(statp, field) \
+	this_cpu_add((statp)->field, 1)
+
+#define this_stat_dec(statp, field) \
+	this_cpu_add((statp)->field, -1)
+
+#define stat_read(statp, field)					\
+({								\
+	typeof((statp)->field) res = 0;				\
+	unsigned int _cpu;					\
+	for_each_possible_cpu(_cpu)				\
+		res += per_cpu_ptr((statp), _cpu)->field;	\
+	res;							\
+})
+
+#define stat_write(statp, field, val)				\
+({								\
+	unsigned int _cpu;					\
+	for_each_possible_cpu(_cpu)				\
+		per_cpu_ptr((statp), _cpu)->field = val;	\
+})
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/xgq_execbuf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/xgq_execbuf.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2021-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XGQ_EXECBUF_H
+#define _XGQ_EXECBUF_H
+
+#include "ert.h"
+#include "xgq_cmd_ert.h"
+
+int xgq_exec_convert_start_cu_cmd(struct xgq_cmd_start_cuidx *xgq_cmd,
+					struct ert_start_kernel_cmd *ecmd);
+int xgq_exec_convert_start_scu_cmd(struct xgq_cmd_start_cuidx *xgq_cmd,
+					struct ert_start_kernel_cmd *ecmd);
+int xgq_exec_convert_start_kv_cu_cmd(struct xgq_cmd_start_cuidx *xgq_cmd,
+				     struct ert_start_kernel_cmd *ecmd);
+int xgq_exec_convert_clock_calib_cmd(struct xgq_cmd_clock_calib *xgq_cmd,
+					struct ert_packet *ecmd);
+int xgq_exec_convert_accessible_cmd(struct xgq_cmd_access_valid *xgq_cmd,
+					struct ert_packet *ecmd);
+int xgq_exec_convert_data_integrity_cmd(struct xgq_cmd_data_integrity *xgq_cmd,
+					struct ert_packet *ecmd);
+#endif /* _XGQ_EXECBUF_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/xrt_cu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/xrt_cu.h
@@ -0,0 +1,568 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Unify CU Model
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_CU_H
+#define _XRT_CU_H
+
+#include <linux/version.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/semaphore.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/kthread.h>
+#include <linux/circ_buf.h>
+#include "kds_command.h"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+#define ioremap_nocache         ioremap
+#endif
+
+#define MAX_CUS 128
+#define MAX_SLOT 32
+
+/* Soft kernel indices are numbered from 0 to some MAX_CUS
+ * but are in a distinct domain which is indiciated by the
+ * first 16 bit of the index used to identify the soft kernel
+ */
+#define SCU_DOMAIN 0x10000
+#define	SOFT_KERNEL_REG_SIZE	4096
+
+/* The normal CU in ip_layout would assign a interrupt
+ * ID in range 0 to 127. Use 128 for m2m cu could ensure
+ * m2m CU is at the end of the CU, which is compatible with
+ * legacy implementation.
+ */
+#define M2M_CU_ID 128
+
+#define xcu_info(xcu, fmt, args...)			\
+	dev_info(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+#define xcu_warn(xcu, fmt, args...)			\
+	dev_warn(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+#define xcu_err(xcu, fmt, args...)			\
+	dev_err(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+#define xcu_dbg(xcu, fmt, args...)			\
+	dev_dbg(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+
+/* XRT CU timer macros */
+/* A low frequence timer per CU to check if CU/command timeout */
+#define CU_TICKS_PER_SEC	2
+#define CU_TIMER		(HZ / CU_TICKS_PER_SEC) /* in jiffies */
+#define CU_EXEC_DEFAULT_TTL	(5UL * CU_TICKS_PER_SEC)
+
+/* HLS CU macros */
+#define CU_AP_START	(0x1 << 0)
+#define CU_AP_DONE	(0x1 << 1)
+#define CU_AP_IDLE	(0x1 << 2)
+#define CU_AP_READY	(0x1 << 3)
+#define CU_AP_CONTINUE	(0x1 << 4)
+#define CU_AP_RESET	(0x1 << 5)
+#define CU_AP_SW_RESET	(0x1 << 8)
+/* Special macro(s) which not defined by HLS CU */
+#define CU_AP_CRASHED	(0xFFFFFFFF)
+
+#define CU_INTR_DONE  0x1
+#define CU_INTR_READY 0x2
+
+enum xcu_model {
+	XCU_HLS,
+	XCU_ACC,
+	XCU_FA,
+	XCU_XGQ,
+	XCU_AUTO,
+};
+
+enum xcu_config_type {
+	CONSECUTIVE_T,
+	PAIRS_T,
+	XGQ_T,
+};
+
+enum xcu_process_result {
+	XCU_IDLE = 0,
+	XCU_BUSY,
+};
+
+/* Let's use HLS style status bits in new_status
+ * Bit 0: start (running)
+ * Bit 1: done
+ * Bit 2: idle
+ */
+struct xcu_status {
+	u32	num_done;
+	u32	num_ready;
+	u32	new_status;
+	u32	rcode;
+};
+
+typedef void *xcu_core_t;
+struct xcu_funcs {
+	/**
+	 * @alloc_credit:
+	 *
+	 * Try to alloc one credit on the CU. A credit is required before
+	 * submit a task to the CU. Otherwise, it would lead to unknown CU
+	 * behaviour.
+	 * Return: the number of remaining credit.
+	 */
+	int (*alloc_credit)(void *core);
+
+	/**
+	 * @free_credit:
+	 *
+	 * free credits.
+	 */
+	void (*free_credit)(void *core, u32 count);
+
+	/**
+	 * @peek_credit:
+	 *
+	 * Check how many credits the CU could provide with side effect.
+	 */
+	int (*peek_credit)(void *core);
+
+	/**
+	 * @configure:
+	 *
+	 * Congifure CU arguments.
+	 *
+	 * There are two types of configuration format.
+	 *
+	 * 1. CONSECUTIVE: Which is a blind copy from data to CU.
+	 * 2. PAIRS: The data contains {offset, val} pairs.
+	 * 3. XGQ: The data contains a XGQ command.
+	 */
+	int (*configure)(void *core, u32 *data, size_t sz, int type);
+
+	/**
+	 * @start:
+	 *
+	 * Start a CU.
+	 */
+	void (*start)(void *core);
+
+	/**
+	 * @check:
+	 *
+	 * Check CU status and the pending task status.
+	 */
+	void (*check)(void *core, struct xcu_status *status, bool force);
+
+	/**
+	 * @submit_config:
+	 *
+	 * This is like configure CU. But it takes xcmd and own it.
+	 *
+	 */
+	int (*submit_config)(void *core, struct kds_command *xcmd);
+
+	/**
+	 * @get_complete:
+	 *
+	 * Get next completed xcmd.
+	 *
+	 */
+	struct kds_command *(*get_complete)(void *core);
+
+	/**
+	 * @abort:
+	 *
+	 */
+	int (*abort)(void *core, void *cond, bool (*match)(struct kds_command *xcmd, void *cond));
+
+	/**
+	 * @reset:
+	 *
+	 * Reset CU.
+	 */
+	void (*reset)(void *core);
+
+	/**
+	 * @reset_done:
+	 *
+	 * Check if CU is properly reset
+	 */
+	bool (*reset_done)(void *core);
+
+	/**
+	 * @enable_intr:
+	 *
+	 * Enable interrupt. Support DONE and READY interrupt.
+	 */
+	void (*enable_intr)(void *core, u32 intr_type);
+
+	/**
+	 * @disable_intr:
+	 *
+	 * Disable interrupt.
+	 */
+	void (*disable_intr)(void *core, u32 intr_type);
+
+	/**
+	 * @clear_intr:
+	 *
+	 * Clear interrupt.
+	 */
+	u32 (*clear_intr)(void *core);
+};
+
+enum arg_dir {
+	DIR_NONE = 0,
+	DIR_INPUT,
+	DIR_OUTPUT
+};
+
+struct xrt_cu_arg {
+	char	name[64];
+	u32	offset;
+	u32	size;
+	u32	dir;
+};
+
+enum CU_PROTOCOL {
+	CTRL_HS = 0,
+	CTRL_CHAIN = 1,
+	CTRL_NONE = 2,
+	CTRL_ME = 3,
+	CTRL_ACC = 4,
+	CTRL_FA = 5
+};
+
+struct xrt_cu_info {
+	u32			 model;
+	int			 cu_idx;
+	u32			 slot_idx;
+	int			 inst_idx;
+	u64			 addr;
+	size_t			 size;
+	u32			 protocol;
+	u32			 intr_id;
+	u32			 is_m2m;
+	u32			 num_res;
+	bool			 intr_enable;
+	bool			 sw_reset;
+	struct xrt_cu_arg	*args;
+	u32			 num_args;
+	char			 iname[64];
+	char			 kname[64];
+	void			*xgq;
+	int			 cu_domain;
+	unsigned char		 uuid[16];
+};
+
+struct per_custat {
+	u64		usage;
+};
+
+#define CU_STATE_GOOD  0x1
+#define CU_STATE_BAD   0x2
+
+/* The Buf size and xrt_cu_log size must be power of 2 */
+#define CIRC_BUF_SIZE 2 * 4096
+struct xrt_cu_log {
+	u64		stage:32;
+	uintptr_t	cmd_id:32;
+	u64		ts;
+};
+#define CU_LOG_STAGE_RQ		1
+#define CU_LOG_STAGE_ISR	2
+#define CU_LOG_STAGE_SQ		3
+#define CU_LOG_STAGE_CQ		4
+
+/* Supported event type */
+struct xrt_cu {
+	struct device		 *dev;
+	struct xrt_cu_info	  info;
+	struct resource		**res;
+	struct list_head	  cu;
+	/* pending queue */
+	struct list_head	  pq;
+	spinlock_t		  pq_lock;
+	u32			  num_pq;
+	/* high priority queue */
+	struct list_head	  hpq;
+	spinlock_t		  hpq_lock;
+	u32			  num_hpq;
+	struct completion	  comp;
+	/*
+	 * Pending Q is used in thread that is submitting CU cmds.
+	 * Other Qs are used in thread that is completing them.
+	 * In order to prevent false sharing, they need to be in different
+	 * cache lines.
+	 */
+	/* run queue */
+	struct list_head	  rq ____cacheline_aligned_in_smp;
+	u32			  num_rq;
+	/* submitted queue */
+	u32			  num_sq;
+	/* completed queue */
+	struct list_head	  cq;
+	u32			  num_cq;
+	struct semaphore	  sem;
+	struct semaphore	  sem_cu;
+	void			 *core;
+	u32			  stop;
+	bool			  bad_state;
+	u32			  done_cnt;
+	u32			  ready_cnt;
+	u32			  status;
+	u32			  rcode;
+	int			  busy_threshold;
+	u32			  interval_min;
+	u32			  interval_max;
+	struct kds_command	 *old_cmd;
+
+	struct mutex		  ev_lock;
+	struct list_head	  events;
+
+	struct timer_list	  timer;
+	atomic_t		  tick;
+	u32			  start_tick;
+
+	struct per_custat	  cu_stat;
+
+	/**
+	 * @funcs:
+	 *
+	 * Compute unit functions.
+	 */
+	struct xcu_funcs          *funcs;
+	/* TODO: Maybe rethink if we should use two threads,
+	 * one for submit, one for complete
+	 */
+	struct task_struct	  *thread;
+	/* Good for debug */
+	u32			   sleep_cnt;
+	u32			   max_running;
+
+	/* support user management CU interrupt */
+	DECLARE_BITMAP(is_ucu, 1);
+	wait_queue_head_t	   ucu_waitq;
+	atomic_t		   ucu_event;
+	int (* user_manage_irq)(struct xrt_cu *xcu, bool user_manage);
+	int (* configure_irq)(struct xrt_cu *xcu, bool enable);
+
+	/* For debug/analysis */
+	char			   debug;
+	char			   log_buf[CIRC_BUF_SIZE] __aligned(sizeof(u64));
+	struct circ_buf		   crc_buf;
+};
+
+static inline char *prot2str(enum CU_PROTOCOL prot)
+{
+	switch (prot) {
+	case CTRL_HS:		return "CTRL_HS";
+	case CTRL_CHAIN:	return "CTRL_CHAIN";
+	case CTRL_NONE:		return "CTRL_NONE";
+	case CTRL_ME:		return "CTRL_ME";
+	case CTRL_ACC:		return "CTRL_ACC";
+	case CTRL_FA:		return "CTRL_FA";
+	default:		return "UNKNOWN";
+	}
+}
+
+static void inline xrt_cu_enable_intr(struct xrt_cu *xcu, u32 intr_type)
+{
+	if (xcu->funcs)
+		xcu->funcs->enable_intr(xcu->core, intr_type);
+}
+
+static void inline xrt_cu_disable_intr(struct xrt_cu *xcu, u32 intr_type)
+{
+	if (xcu->funcs)
+		xcu->funcs->disable_intr(xcu->core, intr_type);
+}
+
+static u32 inline xrt_cu_clear_intr(struct xrt_cu *xcu)
+{
+	return xcu->funcs ? xcu->funcs->clear_intr(xcu->core) : 0;
+}
+
+static inline int xrt_cu_config(struct xrt_cu *xcu, u32 *data, size_t sz, int type)
+{
+	return xcu->funcs->configure(xcu->core, data, sz, type);
+}
+
+static inline void xrt_cu_start(struct xrt_cu *xcu)
+{
+	xcu->funcs->start(xcu->core);
+}
+
+static inline int xrt_cu_submit_config(struct xrt_cu *xcu, struct kds_command *xcmd)
+{
+	if (!xcu->funcs->submit_config)
+		return -EINVAL;
+
+	return xcu->funcs->submit_config(xcu->core, xcmd);
+}
+
+static inline struct kds_command *xrt_cu_get_complete(struct xrt_cu *xcu)
+{
+	if (!xcu->funcs->get_complete)
+		return NULL;
+
+	return xcu->funcs->get_complete(xcu->core);
+}
+
+static inline int
+xrt_cu_cmd_abort(struct xrt_cu *xcu, void *cond,
+		 bool (*match)(struct kds_command *xcmd, void *cond))
+{
+	if (!xcu->funcs->abort)
+		return -EINVAL;
+
+	return xcu->funcs->abort(xcu->core, cond, match);
+}
+
+static inline void xrt_cu_reset(struct xrt_cu *xcu)
+{
+	xcu->funcs->reset(xcu->core);
+}
+
+static inline bool xrt_cu_reset_done(struct xrt_cu *xcu)
+{
+	return xcu->funcs->reset_done(xcu->core);
+}
+
+static inline void __xrt_cu_check(struct xrt_cu *xcu, bool force)
+{
+	struct xcu_status status;
+
+	status.num_done = 0;
+	status.num_ready = 0;
+	status.new_status = 0;
+	status.rcode = 0;
+	xcu->funcs->check(xcu->core, &status, force);
+	/* XRT CU assume command finished in order */
+	xcu->done_cnt += status.num_done;
+	xcu->ready_cnt += status.num_ready;
+	xcu->status = status.new_status;
+	xcu->rcode  = status.rcode;
+}
+
+static inline void xrt_cu_check(struct xrt_cu *xcu)
+{
+	__xrt_cu_check(xcu, false);
+}
+
+static inline void xrt_cu_check_force(struct xrt_cu *xcu)
+{
+	__xrt_cu_check(xcu, true);
+}
+
+static inline int xrt_cu_get_credit(struct xrt_cu *xcu)
+{
+	return xcu->funcs->alloc_credit(xcu->core);
+}
+
+static inline int is_zero_credit(struct xrt_cu *xcu)
+{
+	return (xcu->funcs->peek_credit(xcu->core) == 0);
+}
+
+static inline int xrt_cu_peek_credit(struct xrt_cu *xcu)
+{
+	return xcu->funcs->peek_credit(xcu->core);
+}
+
+static inline void xrt_cu_put_credit(struct xrt_cu *xcu, u32 count)
+{
+	xcu->funcs->free_credit(xcu->core, count);
+}
+
+/* This is a bit trick to calculate next highest power of 2.
+ * If size is a power of 2, the return would be the same as size.
+ */
+static __attribute__((unused))
+u32 round_up_to_next_power2(u32 size)
+{
+	u32 v = --size;
+	v |= v >> 1;
+	v |= v >> 2;
+	v |= v >> 4;
+	v |= v >> 8;
+	v |= v >> 16;
+	return ++v;
+}
+
+/* 1. Move commands from pending command queue to running queue
+ * 2. If CU is ready, submit command(Configure hardware)
+ * 3. Check if submitted command is completed or not
+ */
+void xrt_cu_submit(struct xrt_cu *xcu, struct kds_command *xcmd);
+void xrt_cu_hpq_submit(struct xrt_cu *xcu, struct kds_command *xcmd);
+void xrt_cu_abort(struct xrt_cu *xcu, struct kds_client *client);
+bool xrt_cu_abort_done(struct xrt_cu *xcu, struct kds_client *client);
+int xrt_cu_cfg_update(struct xrt_cu *xcu, int intr);
+int xrt_fa_cfg_update(struct xrt_cu *xcu, u64 bar, u64 dev, void __iomem *vaddr, u32 num_slots);
+int xrt_is_fa(struct xrt_cu *xcu, u32 *size);
+int xrt_cu_get_protocol(struct xrt_cu *xcu);
+u32 xrt_cu_get_status(struct xrt_cu *xcu);
+int xrt_cu_regmap_size(struct xrt_cu *xcu);
+
+int  xrt_cu_init(struct xrt_cu *xcu);
+void xrt_cu_fini(struct xrt_cu *xcu);
+
+ssize_t show_cu_stat(struct xrt_cu *xcu, char *buf);
+ssize_t show_cu_info(struct xrt_cu *xcu, char *buf);
+ssize_t show_formatted_cu_stat(struct xrt_cu *xcu, char *buf);
+
+void xrt_cu_circ_produce(struct xrt_cu *xcu, u32 stage, uintptr_t cmd);
+ssize_t xrt_cu_circ_consume_all(struct xrt_cu *xcu, char *buf, size_t size);
+
+int xrt_cu_process_queues(struct xrt_cu *xcu);
+
+/* CU Implementations */
+int xrt_cu_hls_init(struct xrt_cu *xcu);
+void xrt_cu_hls_fini(struct xrt_cu *xcu);
+
+typedef struct {
+	u32 argOffset;
+	u32 argSize;
+	u32 argValue[];
+} descEntry_t;
+
+typedef struct {
+	u32 status;
+	u32 numInputEntries;
+	u32 inputEntryBytes;
+	u32 numOutputEntries;
+	u32 outputEntryBytes;
+	u32 data[];
+} descriptor_t;
+
+#define to_cu_fa(core) ((struct xrt_cu_fa *)(core))
+struct xrt_cu_fa {
+	void __iomem		*vaddr;
+	void __iomem		*cmdmem;
+	u64			 paddr;
+	u32			 slot_sz;
+	u32			 num_slots;
+	u32			 head_slot;
+	u32			 desc_msw;
+	u32			 task_cnt;
+	int			 max_credits;
+	int			 credits;
+	int			 run_cnts;
+	u64			 check_count;
+
+	struct list_head	 submitted;
+	struct list_head	 completed;
+};
+
+int xrt_cu_fa_init(struct xrt_cu *xcu);
+void xrt_cu_fa_fini(struct xrt_cu *xcu);
+
+int xrt_cu_scu_init(struct xrt_cu *xcu, void *vaddr, struct semaphore *sem);
+void xrt_cu_scu_fini(struct xrt_cu *xcu);
+
+#endif /* _XRT_CU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/xrt_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/xrt_drv.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style device manager for PCIe based OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_DRV_H
+#define _XRT_DRV_H
+
+#define XRT_DRV_BO_DEVICE_MEM 	(1 << 31)
+#define XRT_DRV_BO_HOST_MEM	(1 << 30)
+#define XRT_DRV_BO_DRV_ALLOC	(1 << 29)
+#define XRT_DRV_BO_DRM_IMPORT 	(1 << 28)
+#define XRT_DRV_BO_P2P		(1 << 27)
+#define XRT_DRV_BO_DRM_SHMEM	(1 << 26)
+#define XRT_DRV_BO_USER_ALLOC	(1 << 25)
+#define XRT_DRV_BO_CMA		(1 << 24)
+#define XRT_DRV_BO_CACHEABLE	(1 << 23)
+#define XRT_DRV_BO_SGL		(1 << 22)
+#define XRT_DRV_BO_KERN_BUF	(1 << 21)
+
+/* Versal transfer cache packet definition */
+
+#define	XRT_XFR_VER			1
+
+/*
+ * Note: we should keep the existing PKT status and flags
+ *       stable to not breaking the old versal platform
+ */
+#define	XRT_XFR_PKT_STATUS_IDLE		0
+#define	XRT_XFR_PKT_STATUS_NEW		1
+#define	XRT_XFR_PKT_STATUS_DONE		2
+#define	XRT_XFR_PKT_STATUS_FAIL		3
+
+#define	XRT_XFR_PKT_TYPE_SHIFT		1
+#define	XRT_XFR_PKT_TYPE_MASK		7
+
+#define	XRT_XFR_PKT_VER_SHIFT		4
+#define	XRT_XFR_PKT_VER_MASK		3
+
+#define	XRT_XFR_PKT_TYPE_PDI		0
+#define	XRT_XFR_PKT_TYPE_XCLBIN		1
+
+#define	XRT_XFR_PKT_FLAGS_LAST		(1 << 0)
+#define	XRT_XFR_PKT_FLAGS_PDI		(XRT_XFR_PKT_TYPE_PDI << \
+	XRT_XFR_PKT_TYPE_SHIFT)
+#define	XRT_XFR_PKT_FLAGS_XCLBIN	(XRT_XFR_PKT_TYPE_XCLBIN << \
+	XRT_XFR_PKT_TYPE_SHIFT)
+#define	XRT_XFR_PKT_FLAGS_VER		(XRT_XFR_VER << XRT_XFR_PKT_VER_SHIFT)
+
+struct pdi_packet {
+	union {
+		struct {
+			u8	pkt_status;
+			u8	pkt_flags;
+			u16	pkt_size;
+		};
+		u32 header;
+	};
+} __packed;
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/xrt_ert.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/xrt_ert.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx ERT Model
+ *
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: chienwei@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_ERT_H
+#define _XRT_ERT_H
+
+#include "ert.h"
+#include "kds_command.h"
+#include "xgq_cmd_common.h"
+
+struct xrt_ert_command;
+
+struct ert_cmd_ops {
+	void (*complete)(struct xrt_ert_command *ecmd, void *core);
+	void (*notify)(void *core);
+	void (*free_payload)(void *payload);
+};
+
+struct xrt_ert_command {
+	struct list_head		list;
+	struct kds_command		*xcmd;
+
+	uint32_t			handle;
+
+	void 				*client;
+	struct ert_cmd_ops		cb;
+	uint32_t			*payload;
+	// payload size in words
+	uint32_t			payload_size;
+	uint32_t			cu_idx;
+	struct xgq_com_queue_entry	complete_entry;
+	uint32_t			response_size;
+
+	uint32_t			response[0];
+};
+
+struct ert_queue {
+	void				*handle;
+	struct xrt_ert_queue_funcs	*func;
+	uint64_t			size;
+};
+
+struct xrt_ert_queue_funcs {
+
+	void (*poll)(void *queue_handle);
+
+	int (*submit)(struct xrt_ert_command *ecmd, void *queue_handle);
+
+	int  (*queue_config)(uint32_t slot_size, bool polling, void *ert_handle, void *queue_handle);
+
+	uint32_t (*max_slot_num)(void *queue_handle);
+
+	void (*abort)(void *client, void *queue_handle);
+
+	void (*intc_config)(bool enable, void *queue_handle);
+
+};
+
+#endif /* _XRT_ERT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/include/xrt_xclbin.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/include/xrt_xclbin.h
@@ -0,0 +1,80 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver XCLBIN parser
+ *
+ * Copyright (C) 2020-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: David Zhang <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_XCLBIN_H
+#define _XRT_XCLBIN_H
+
+#include <linux/types.h>
+
+/* Used for parsing bitstream header */
+#define XHI_EVEN_MAGIC_BYTE     0x0f
+#define XHI_ODD_MAGIC_BYTE      0xf0
+
+/* Extra mode for IDLE */
+#define XHI_OP_IDLE  -1
+#define XHI_BIT_HEADER_FAILURE -1
+
+/* The imaginary module length register */
+#define XHI_MLR                  15
+
+#define DMA_HWICAP_BITFILE_BUFFER_SIZE 1024
+
+enum axlf_section_kind;
+struct axlf_section_header;
+struct axlf;
+
+/**
+ * Bitstream header information.
+ */
+struct XHwIcap_Bit_Header {
+	unsigned int HeaderLength;     /* Length of header in 32 bit words */
+	unsigned int BitstreamLength;  /* Length of bitstream to read in bytes*/
+	unsigned char *DesignName;     /* Design name get from bitstream */
+	unsigned char *PartName;       /* Part name read from bitstream */
+	unsigned char *Date;           /* Date read from bitstream header */
+	unsigned char *Time;           /* Bitstream creation time*/
+	unsigned int MagicLength;      /* Length of the magic numbers*/
+};
+
+int
+xrt_xclbin_parse_header(const unsigned char *data,
+	unsigned int size, struct XHwIcap_Bit_Header *header);
+
+void
+xrt_xclbin_free_header(struct XHwIcap_Bit_Header *header);
+
+char *
+xrt_xclbin_kind_to_string(enum axlf_section_kind kind);
+
+const struct axlf_section_header *
+xrt_xclbin_get_section_hdr(const struct axlf *xclbin, enum axlf_section_kind kind);
+
+int
+xrt_xclbin_check_section_hdr(const struct axlf_section_header *header,
+	uint64_t xclbin_len);
+
+int
+xrt_xclbin_section_info(const struct axlf *xclbin, enum axlf_section_kind kind,
+	uint64_t *offset, uint64_t *size);
+
+int
+xrt_xclbin_get_section(const struct axlf *xclbin,
+	enum axlf_section_kind kind, void **data, uint64_t *len);
+
+struct axlf_section_header *
+xrt_xclbin_get_section_hdr_next(const struct axlf *xclbin,
+	enum axlf_section_kind kind, struct axlf_section_header *cur);
+
+int xrt_xclbin_get_section_num(const struct axlf *xclbin,
+	enum axlf_section_kind kind);
+
+#endif /* _XRT_XCLBIN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/kds_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/kds_core.c
@@ -0,0 +1,2106 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/slab.h>
+#include <linux/sched.h>
+#include <linux/vmalloc.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/poll.h>
+#include <linux/anon_inodes.h>
+#include "kds_core.h"
+
+/* for sysfs */
+int store_kds_echo(struct kds_sched *kds, const char *buf, size_t count,
+		   int *echo)
+{
+	u32 enable;
+	u32 live_clients;
+
+	live_clients = kds_live_clients(kds, NULL);
+	/* Ideally, KDS should be locked to reject new client.
+	 * But, this node is hidden for internal test purpose.
+	 * Let's refine it after new KDS is the default and
+	 * user is allow to configure it through xbutil.
+	 */
+	if (live_clients > 0)
+		return -EBUSY;
+
+	if (kstrtou32(buf, 10, &enable) == -EINVAL || enable > 1)
+		return -EINVAL;
+
+	*echo = enable;
+
+	return count;
+}
+
+/* Each line is a CU, format:
+ * "cu_idx kernel_name:cu_name address status usage"
+ */
+ssize_t show_kds_custat_raw(struct kds_sched *kds, char *buf)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	struct xrt_cu *xcu = NULL;
+	char *cu_fmt = "%d,%d,%s:%s,0x%llx,0x%x,%llu\n";
+	ssize_t sz = 0;
+	int i;
+	int j;
+
+	mutex_lock(&cu_mgmt->lock);
+	for (j = 0; j < MAX_SLOT; ++j) {
+		for (i = 0; i < MAX_CUS; ++i) {
+			xcu = cu_mgmt->xcus[i];
+			if (!xcu)
+				continue;
+
+			/* Show the CUs as per slot order */
+			if (xcu->info.slot_idx == j) {
+				sz += scnprintf(buf+sz, PAGE_SIZE - sz, cu_fmt, j, i,
+						xcu->info.kname, xcu->info.iname,
+						xcu->info.addr, xcu->status,
+						cu_stat_read(cu_mgmt, usage[i]));
+			}
+		}
+	}
+	mutex_unlock(&cu_mgmt->lock);
+
+	return sz;
+}
+
+/* Each line is a PS kernel, format:
+ * "idx kernel_name status usage"
+ */
+ssize_t show_kds_scustat_raw(struct kds_sched *kds, char *buf)
+{
+	struct kds_scu_mgmt *scu_mgmt = &kds->scu_mgmt;
+	char *cu_fmt = "%d,%d,%s:%s,0x%x,%u\n";
+	struct xrt_cu *xcu = NULL;
+	ssize_t sz = 0;
+	int i;
+	int j;
+
+	/* TODO: The number of PS kernel could be 64 or even more.
+	 * Sysfs has PAGE_SIZE limit, which keep bother us in old KDS.
+	 * In 128 PS kernels case, each line is average 32 bytes.
+	 * The kernel name is no more than 19 bytes.
+	 *
+	 * Old KDS shows FPGA Kernel and PS kernel in one file.
+	 * So, this separate kds_scustat_raw is better.
+	 *
+	 * But in the worst case, this is still not good enough.
+	 *
+	 * Soft kernels are namespaced with a domain identifer that
+	 * is or'ed into the scu index.	 For soft kernels the
+	 * domain is SCU_DOMAIN.
+	 */
+	mutex_lock(&scu_mgmt->lock);
+	for (j = 0; j < MAX_SLOT; ++j) {
+		for (i = 0; i < MAX_CUS; ++i) {
+			xcu = scu_mgmt->xcus[i];
+			if (!xcu)
+				continue;
+
+			/* Show the CUs as per slot order */
+			if (xcu->info.slot_idx != j)
+				continue;
+
+			sz += scnprintf(buf+sz, PAGE_SIZE - sz, cu_fmt, j,
+					(i | SCU_DOMAIN), xcu->info.kname,xcu->info.iname,
+					xcu->status,
+					cu_stat_read(scu_mgmt,usage[i]));
+		}
+	}
+	mutex_unlock(&scu_mgmt->lock);
+
+	return sz;
+}
+
+ssize_t show_kds_stat(struct kds_sched *kds, char *buf)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	char *cu_fmt = "  CU[%d] usage(%llu) shared(%d) refcnt(%d) intr(%s)\n";
+	ssize_t sz = 0;
+	bool shared;
+	int ref;
+	int i;
+
+	mutex_lock(&cu_mgmt->lock);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz,
+			"CU to host interrupt capability: %d\n",
+			kds->cu_intr_cap);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Interrupt mode: %s\n",
+			(KDS_SETTING(kds->cu_intr))? "cu" : "ert");
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Number of CUs: %d\n",
+			cu_mgmt->num_cus);
+	for (i = 0; i < MAX_CUS; ++i) {
+		if (!cu_mgmt->xcus[i])
+			continue;
+
+		shared = !(cu_mgmt->cu_refs[i] & CU_EXCLU_MASK);
+		ref = cu_mgmt->cu_refs[i] & ~CU_EXCLU_MASK;
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, cu_fmt, i,
+				cu_stat_read(cu_mgmt, usage[i]), shared, ref,
+				(cu_mgmt->cu_intr[i])? "enable" : "disable");
+	}
+	mutex_unlock(&cu_mgmt->lock);
+
+	return sz;
+}
+/* sysfs end */
+
+static int
+kds_wake_up_poll(struct kds_sched *kds)
+{
+	if (kds->polling_start) {
+		kds->polling_start = 0;
+		return 1;
+	}
+
+	if (kds->polling_stop)
+		return 1;
+
+	return 0;
+}
+
+static int kds_polling_thread(void *data)
+{
+	struct kds_sched *kds = (struct kds_sched *)data;
+	int busy_cnt = 0;
+	int loop_cnt = 0;
+
+	while (!kds->polling_stop) {
+		struct xrt_cu *xcu;
+		busy_cnt = 0;
+
+		list_for_each_entry(xcu, &kds->alive_cus, cu) {
+			if (xrt_cu_process_queues(xcu) == XCU_BUSY)
+				busy_cnt += 1;
+		}
+
+		/* If kds->interval is 0, keep poling CU without sleeping.
+		 * If kds->interval is greater than 0, this thread will sleep
+		 * interval to interval + 3 microseconds.
+		 */
+		if (kds->interval > 0)
+			usleep_range(kds->interval, kds->interval + 3);
+
+		/* Avoid large num_rq leads to more 120 sec blocking */
+		if (++loop_cnt == 8) {
+			loop_cnt = 0;
+			schedule();
+		}
+
+		if (busy_cnt != 0)
+			continue;
+
+		wait_event_interruptible(kds->wait_queue, kds_wake_up_poll(kds));
+	}
+
+	return 0;
+}
+
+/**
+ * get_cu_by_addr -Get CU index by address
+ *
+ * @cu_mgmt: KDS CU management struct
+ * @addr: The address of the target CU
+ *
+ * Returns CU index if found. Returns an out of range number if not found.
+ */
+static __attribute__((unused)) int
+get_cu_by_addr(struct kds_cu_mgmt *cu_mgmt, u32 addr)
+{
+	int i;
+
+	/* Do not use this search in critical path */
+	for (i = 0; i < MAX_CUS; ++i) {
+		if (!cu_mgmt->xcus[i])
+			continue;
+
+		if (cu_mgmt->xcus[i]->info.addr == addr)
+			break;
+	}
+
+	return i;
+}
+
+static int
+kds_scu_config(struct kds_scu_mgmt *scu_mgmt, struct kds_command *xcmd)
+{
+	struct ert_configure_sk_cmd *scmd;
+	int i, j;
+
+	scmd = (struct ert_configure_sk_cmd *)xcmd->execbuf;
+	mutex_lock(&scu_mgmt->lock);
+	for (i = 0; i < scmd->num_image; i++) {
+		struct config_sk_image *cp = &scmd->image[i];
+
+		for (j = 0; j < cp->num_cus; j++) {
+			u32 scu_idx = j + cp->start_cuidx;
+
+			/*
+			 * TODO: Need consider size limit of the name.
+			 * In case PAGE_SIZE sysfs node cannot show all
+			 * SCUs (more than 64 SCUs or up to 128).
+			 */
+			strncpy(scu_mgmt->name[scu_idx], (char *)cp->sk_name,
+				sizeof(scu_mgmt->name[0]));
+
+			cu_stat_write(scu_mgmt, usage[scu_idx], 0);
+		}
+	}
+	mutex_unlock(&scu_mgmt->lock);
+
+	return 0;
+}
+
+/**
+ * acquire_cu_idx - Get ready CU index
+ *
+ * @xcmd: Command
+ *
+ * Returns: Negative value for error. 0 or positive value for index
+ *
+ */
+static u32
+acquire_cu_idx(struct kds_cu_mgmt *cu_mgmt, struct kds_command *xcmd)
+{
+	struct kds_client *client = xcmd->client;
+	/* User marked CUs */
+	uint8_t user_cus[MAX_CUS];
+	int num_marked;
+	/* After validation */
+	uint8_t valid_cus[MAX_CUS];
+	int num_valid = 0;
+	uint8_t index;
+	u64 usage;
+	u64 min_usage;
+	int i;
+
+	num_marked = cu_mask_to_cu_idx(xcmd, user_cus);
+	if (unlikely(num_marked > cu_mgmt->num_cus)) {
+		kds_err(client, "Too many CUs in CU mask");
+		return -EINVAL;
+	}
+
+	/* Check if CU is added in the context */
+	for (i = 0; i < num_marked; ++i) {
+		if (test_bit(user_cus[i], client->cu_bitmap)) {
+			valid_cus[num_valid] = user_cus[i];
+			++num_valid;
+		}
+	}
+
+	if (num_valid == 1) {
+		index = valid_cus[0];
+		goto out;
+	} else if (num_valid == 0) {
+		kds_err(client, "All CUs in mask are out of context");
+		return -EINVAL;
+	}
+
+	/* Find out the CU with minimum usage */
+	for (i = 1, index = valid_cus[0]; i < num_valid; ++i) {
+		usage = cu_stat_read(cu_mgmt, usage[valid_cus[i]]);
+		min_usage = cu_stat_read(cu_mgmt, usage[index]);
+		if (usage < min_usage)
+			index = valid_cus[i];
+	}
+
+out:
+	if (xrt_cu_get_protocol(cu_mgmt->xcus[index]) == CTRL_NONE) {
+		kds_err(client, "Cannot submit command to ap_ctrl_none CU");
+		return -EINVAL;
+	}
+
+	if (test_bit(0, cu_mgmt->xcus[index]->is_ucu))
+		return -EBUSY;
+
+	cu_stat_inc(cu_mgmt, usage[index]);
+	client_stat_inc(client, s_cnt[index]);
+	xcmd->cu_idx = index;
+	/* Before it go, make sure selected CU is still opening. */
+	if (unlikely(!test_bit(index, client->cu_bitmap))) {
+		client_stat_dec(client, s_cnt[index]);
+		index = -EAGAIN;
+	}
+
+	return index;
+}
+
+/**
+ * acquire_scu_idx - Get ready SCU index
+ *
+ * @xcmd: Command
+ *
+ * Returns: Negative value for error. 0 or positive value for index
+ *
+ */
+static int
+acquire_scu_idx(struct kds_scu_mgmt *scu_mgmt, struct kds_command *xcmd)
+{
+	struct kds_client *client = xcmd->client;
+	/* User marked CUs */
+	uint8_t user_cus[MAX_CUS];
+	int num_marked;
+	/* After validation */
+	uint8_t valid_cus[MAX_CUS];
+	int num_valid = 0;
+	uint8_t index;
+	u64 usage;
+	u64 min_usage;
+	int i;
+
+	num_marked = cu_mask_to_cu_idx(xcmd, user_cus);
+	if (unlikely(num_marked > scu_mgmt->num_cus)) {
+		kds_err(client, "Too many CUs in CU mask");
+		return -EINVAL;
+	}
+
+	/* Check if CU is added in the context */
+	for (i = 0; i < num_marked; ++i) {
+		if (test_bit(user_cus[i], client->scu_bitmap)) {
+			valid_cus[num_valid] = user_cus[i];
+			++num_valid;
+		}
+	}
+
+	if (num_valid == 1) {
+		index = valid_cus[0];
+		goto out;
+	} else if (num_valid == 0) {
+		kds_err(client, "All CUs in mask are out of context");
+		return -EINVAL;
+	}
+
+	/* Find out the CU with minimum usage */
+	for (i = 1, index = valid_cus[0]; i < num_valid; ++i) {
+		usage = cu_stat_read(scu_mgmt, usage[valid_cus[i]]);
+		min_usage = cu_stat_read(scu_mgmt, usage[index]);
+		if (usage < min_usage)
+			index = valid_cus[i];
+	}
+
+out:
+	cu_stat_inc(scu_mgmt, usage[index]);
+	client_stat_inc(client, scu_s_cnt[index]);
+	xcmd->cu_idx = index;
+	/* Before it go, make sure selected CU is still opening. */
+	if (unlikely(!test_bit(index, client->scu_bitmap))) {
+		client_stat_dec(client, scu_s_cnt[index]);
+		index = -EAGAIN;
+	}
+
+	return index;
+}
+
+static int
+kds_cu_dispatch(struct kds_cu_mgmt *cu_mgmt, struct kds_command *xcmd)
+{
+	int cu_idx = 0;
+
+	do {
+		cu_idx = acquire_cu_idx(cu_mgmt, xcmd);
+	} while(cu_idx == -EAGAIN);
+	if (cu_idx < 0)
+		return cu_idx;
+
+	xrt_cu_submit(cu_mgmt->xcus[cu_idx], xcmd);
+	set_xcmd_timestamp(xcmd, KDS_QUEUED);
+	return 0;
+}
+
+static int
+kds_scu_dispatch(struct kds_scu_mgmt *scu_mgmt, struct kds_command *xcmd)
+{
+	int cu_idx = 0;
+
+	do {
+		cu_idx = acquire_scu_idx(scu_mgmt, xcmd);
+	} while(cu_idx == -EAGAIN);
+	if (cu_idx < 0)
+		return cu_idx;
+
+	xrt_cu_submit(scu_mgmt->xcus[cu_idx], xcmd);
+	set_xcmd_timestamp(xcmd, KDS_QUEUED);
+	return 0;
+}
+
+static void
+kds_cu_abort_cmd(struct kds_cu_mgmt *cu_mgmt, struct kds_command *xcmd)
+{
+	struct kds_sched *kds;
+	int i;
+
+	/* Broadcast abort command to each CU and let CU finds out how to abort
+	 * the target command.
+	 */
+	for (i = 0; i < MAX_CUS; i++) {
+		if (!cu_mgmt->xcus[i])
+			continue;
+
+		xrt_cu_hpq_submit(cu_mgmt->xcus[i], xcmd);
+
+		if (xcmd->status == KDS_NEW)
+			continue;
+
+		if (xcmd->status == KDS_TIMEOUT) {
+			kds = container_of(cu_mgmt, struct kds_sched, cu_mgmt);
+			kds->bad_state = 1;
+			kds_info(xcmd->client, "CU(%d) hangs, reset device", i);
+		}
+
+		xcmd->cb.notify_host(xcmd, xcmd->status);
+		xcmd->cb.free(xcmd);
+		return;
+	}
+
+	/* Command is not found in any CUs and any queues */
+	xcmd->status = KDS_ERROR;
+	xcmd->cb.notify_host(xcmd, xcmd->status);
+	xcmd->cb.free(xcmd);
+}
+
+static void
+kds_scu_abort_cmd(struct kds_scu_mgmt *scu_mgmt, struct kds_command *xcmd)
+{
+	struct kds_sched *kds;
+	int i;
+
+	/* Broadcast abort command to each CU and let CU finds out how to abort
+	 * the target command.
+	 */
+	for (i = 0; i < scu_mgmt->num_cus; i++) {
+		xrt_cu_hpq_submit(scu_mgmt->xcus[i], xcmd);
+
+		if (xcmd->status == KDS_NEW)
+			continue;
+
+		if (xcmd->status == KDS_TIMEOUT) {
+			kds = container_of(scu_mgmt, struct kds_sched, scu_mgmt);
+			kds->bad_state = 1;
+			kds_info(xcmd->client, "CU(%d) hangs, reset device", i);
+		}
+
+		xcmd->cb.notify_host(xcmd, xcmd->status);
+		xcmd->cb.free(xcmd);
+		return;
+	}
+
+	/* Command is not found in any CUs and any queues */
+	xcmd->status = KDS_ERROR;
+	xcmd->cb.notify_host(xcmd, xcmd->status);
+	xcmd->cb.free(xcmd);
+}
+
+static int
+kds_submit_cu(struct kds_sched *kds, struct kds_command *xcmd)
+{
+	int ret = 0;
+
+	switch (xcmd->opcode) {
+	case OP_START:
+		ret = kds_cu_dispatch(&kds->cu_mgmt, xcmd);
+		if (!ret && (kds->ert_disable || kds->xgq_enable)) {
+			kds->polling_start = 1;
+			wake_up_interruptible(&kds->wait_queue);
+		}
+		break;
+	case OP_CONFIG:
+		/* No need to config for KDS mode */
+	case OP_GET_STAT:
+		xcmd->cb.notify_host(xcmd, KDS_COMPLETED);
+		xcmd->cb.free(xcmd);
+		break;
+	case OP_ABORT:
+		kds_cu_abort_cmd(&kds->cu_mgmt, xcmd);
+		break;
+	default:
+		ret = -EINVAL;
+		kds_err(xcmd->client, "Unknown opcode");
+	}
+
+	return ret;
+}
+
+static int
+kds_submit_scu(struct kds_sched *kds, struct kds_command *xcmd)
+{
+	int ret = 0;
+
+	switch (xcmd->opcode) {
+	case OP_START_SK:
+		ret = kds_scu_dispatch(&kds->scu_mgmt, xcmd);
+		if (!ret && (kds->ert_disable || kds->xgq_enable)) {
+			kds->polling_start = 1;
+			wake_up_interruptible(&kds->wait_queue);
+		}
+		break;
+	case OP_CONFIG:
+		break;
+	case OP_GET_STAT:
+		xcmd->cb.notify_host(xcmd, KDS_COMPLETED);
+		xcmd->cb.free(xcmd);
+		break;
+	case OP_ABORT:
+		kds_scu_abort_cmd(&kds->scu_mgmt, xcmd);
+		break;
+	default:
+		ret = -EINVAL;
+		kds_err(xcmd->client, "Unknown opcode");
+	}
+
+	return ret;
+}
+
+static int
+kds_submit_ert(struct kds_sched *kds, struct kds_command *xcmd)
+{
+	struct kds_ert *ert = kds->ert;
+	int ret = 0;
+	int cu_idx = 0;
+
+	/* BUG_ON(!ert || !ert->submit); */
+
+	switch (xcmd->opcode) {
+	case OP_START:
+		/* KDS should select a CU and set it in cu_mask */
+		do {
+			cu_idx = acquire_cu_idx(&kds->cu_mgmt, xcmd);
+		} while(cu_idx == -EAGAIN);
+		if (cu_idx < 0)
+			return cu_idx;
+		break;
+	case OP_CONFIG_SK:
+		ret = kds_scu_config(&kds->scu_mgmt, xcmd);
+		if (ret)
+			return ret;
+		break;
+	case OP_GET_STAT:
+		if (!kds->scu_mgmt.num_cus) {
+			xcmd->cb.notify_host(xcmd, KDS_COMPLETED);
+			xcmd->cb.free(xcmd);
+			return 0;
+		}
+		break;
+	case OP_CONFIG:
+	case OP_START_SK:
+	case OP_CLK_CALIB:
+	case OP_VALIDATE:
+		break;
+	default:
+		kds_err(xcmd->client, "Unknown opcode");
+		return -EINVAL;
+	}
+
+	ert->submit(ert, xcmd);
+	set_xcmd_timestamp(xcmd, KDS_QUEUED);
+	return 0;
+}
+
+static int
+kds_add_cu_context(struct kds_sched *kds, struct kds_client *client,
+		   struct kds_ctx_info *info)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	u32 cu_idx = info->cu_idx;
+	u32 prop;
+	bool shared;
+	int ret = 0;
+
+	if ((cu_idx >= MAX_CUS) || (!cu_mgmt->xcus[cu_idx])) {
+		kds_err(client, "CU(%d) not found", cu_idx);
+		return -EINVAL;
+	}
+
+	if (test_and_set_bit(cu_idx, client->cu_bitmap)) {
+		kds_err(client, "CU(%d) has been added", cu_idx);
+		return -EINVAL;
+	}
+
+	prop = info->flags & CU_CTX_PROP_MASK;
+	shared = (prop != CU_CTX_EXCLUSIVE);
+
+	/* cu_mgmt->cu_refs is the critical section of multiple clients */
+	mutex_lock(&cu_mgmt->lock);
+	/* Must check exclusive bit is set first */
+	if (cu_mgmt->cu_refs[cu_idx] & CU_EXCLU_MASK) {
+		kds_err(client, "CU(%d) has been exclusively reserved", cu_idx);
+		ret = -EBUSY;
+		goto err;
+	}
+
+	/* Not allow exclusively reserved if CU is shared */
+	if (!shared && cu_mgmt->cu_refs[cu_idx]) {
+		kds_err(client, "CU(%d) has been shared", cu_idx);
+		ret = -EBUSY;
+		goto err;
+	}
+
+	/* CU is not shared and not exclusively reserved */
+	if (!shared)
+		cu_mgmt->cu_refs[cu_idx] |= CU_EXCLU_MASK;
+	else
+		++cu_mgmt->cu_refs[cu_idx];
+	mutex_unlock(&cu_mgmt->lock);
+
+	return 0;
+err:
+	mutex_unlock(&cu_mgmt->lock);
+	clear_bit(cu_idx, client->cu_bitmap);
+	return ret;
+}
+
+static int
+kds_del_cu_context(struct kds_sched *kds, struct kds_client *client,
+		   struct kds_ctx_info *info)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	u32 cu_idx = info->cu_idx;
+	unsigned long submitted;
+	unsigned long completed;
+	bool bad_state = false;
+	int wait_ms;
+
+	if ((cu_idx >= MAX_CUS) || (!cu_mgmt->xcus[cu_idx])) {
+	        kds_err(client, "Client pid(%d) CU(%d) not found", pid_nr(client->pid), cu_idx);
+		return -EINVAL;
+	}
+
+	if (!test_and_clear_bit(cu_idx, client->cu_bitmap)) {
+		kds_err(client, "Client pid(%d) CU(%d) has never been reserved", pid_nr(client->pid), cu_idx);
+		return -EINVAL;
+	}
+
+	/* Before close, make sure no remain commands in CU's queue. */
+	submitted = client_stat_read(client, s_cnt[cu_idx]);
+	completed = client_stat_read(client, c_cnt[cu_idx]);
+	if (submitted == completed)
+		goto skip;
+
+	if (kds->ert_disable || kds->xgq_enable) {
+		wait_ms = 500;
+		xrt_cu_abort(cu_mgmt->xcus[cu_idx], client);
+
+		/* sub-device that handle command should do abort with a timeout */
+		do {
+			kds_warn(client, "%ld outstanding command(s) on CU(%d)",
+				 submitted - completed, cu_idx);
+			msleep(wait_ms);
+			submitted = client_stat_read(client, s_cnt[cu_idx]);
+			completed = client_stat_read(client, c_cnt[cu_idx]);
+		} while (submitted != completed);
+
+		bad_state = xrt_cu_abort_done(cu_mgmt->xcus[cu_idx], client);
+	} else if (!kds->ert->abort_sync) {
+		/* TODO: once ert_user sub-dev implemented abort_sync(), we can
+		 * remove this branch.
+		 */
+		wait_ms = 500;
+		kds->ert->abort(kds->ert, client, cu_idx);
+
+		do {
+			kds_warn(client, "%ld outstanding command(s) on CU(%d)",
+				 submitted - completed, cu_idx);
+			msleep(wait_ms);
+			submitted = client_stat_read(client, s_cnt[cu_idx]);
+			completed = client_stat_read(client, c_cnt[cu_idx]);
+		} while (submitted != completed);
+
+		bad_state = kds->ert->abort_done(kds->ert, client, cu_idx);
+	} else if (kds->ert->abort_sync) {
+		/* Wait 5 seconds */
+		wait_ms = 5000;
+		do {
+			kds_warn(client, "%ld outstanding command(s) on CU(%d)",
+				 submitted - completed, cu_idx);
+			msleep(500);
+			wait_ms -= 500;
+			submitted = client_stat_read(client, s_cnt[cu_idx]);
+			completed = client_stat_read(client, c_cnt[cu_idx]);
+			if (submitted == completed)
+				break;
+		} while (wait_ms);
+
+		if (submitted != completed)
+			kds->ert->abort_sync(kds->ert, client, cu_idx);
+	}
+
+	if (bad_state) {
+		kds->bad_state = 1;
+		kds_info(client, "CU(%d) hangs, please reset device", cu_idx);
+	}
+
+skip:
+	/* cu_mgmt->cu_refs is the critical section of multiple clients */
+	mutex_lock(&cu_mgmt->lock);
+	if (cu_mgmt->cu_refs[cu_idx] & CU_EXCLU_MASK)
+		cu_mgmt->cu_refs[cu_idx] = 0;
+	else
+		--cu_mgmt->cu_refs[cu_idx];
+	mutex_unlock(&cu_mgmt->lock);
+
+	return 0;
+}
+
+static int
+kds_add_scu_context(struct kds_sched *kds, struct kds_client *client,
+		   struct kds_ctx_info *info)
+{
+	struct kds_scu_mgmt *scu_mgmt = &kds->scu_mgmt;
+	u32 cu_idx = info->cu_idx;
+	u32 prop = 0;
+	bool shared;
+	int ret = 0;
+
+	if ((cu_idx >= MAX_CUS) || (!scu_mgmt->xcus[cu_idx])) {
+		kds_err(client, "SCU(%d) not found", cu_idx);
+		return -EINVAL;
+	}
+
+	if (test_and_set_bit(cu_idx, client->scu_bitmap)) {
+		kds_err(client, "SCU(%d) has been added", cu_idx);
+		return -EINVAL;
+	}
+
+	prop = info->flags & CU_CTX_PROP_MASK;
+	shared = (prop != CU_CTX_EXCLUSIVE);
+
+	/* scu_mgmt->cu_refs is the critical section of multiple clients */
+	mutex_lock(&scu_mgmt->lock);
+	/* Must check exclusive bit is set first */
+	if (scu_mgmt->cu_refs[cu_idx] & CU_EXCLU_MASK) {
+		kds_err(client, "CU(%d) has been exclusively reserved", cu_idx);
+		ret = -EBUSY;
+		goto err;
+	}
+
+	/* Not allow exclusively reserved if CU is shared */
+	if (!shared && scu_mgmt->cu_refs[cu_idx]) {
+		kds_err(client, "CU(%d) has been shared", cu_idx);
+		ret = -EBUSY;
+		goto err;
+	}
+
+	/* CU is not shared and not exclusively reserved */
+	if (!shared)
+		scu_mgmt->cu_refs[cu_idx] |= CU_EXCLU_MASK;
+	else
+		++scu_mgmt->cu_refs[cu_idx];
+	mutex_unlock(&scu_mgmt->lock);
+
+	return 0;
+err:
+	mutex_unlock(&scu_mgmt->lock);
+	clear_bit(cu_idx, client->scu_bitmap);
+	return ret;
+}
+
+static int
+kds_del_scu_context(struct kds_sched *kds, struct kds_client *client,
+		   struct kds_ctx_info *info)
+{
+	struct kds_scu_mgmt *scu_mgmt = &kds->scu_mgmt;
+	u32 cu_idx = info->cu_idx;
+	unsigned long submitted = 0;
+	unsigned long completed = 0;
+	bool bad_state = false;
+
+	if ((cu_idx >= MAX_CUS) || (!scu_mgmt->xcus[cu_idx])) {
+		kds_err(client, "SCU(%d) not found", cu_idx);
+		return -EINVAL;
+	}
+
+	if (!test_and_clear_bit(cu_idx, client->scu_bitmap)) {
+		kds_err(client, "SCU(%d) has never been reserved", cu_idx);
+		return -EINVAL;
+	}
+
+	/* Before close, make sure no remain commands in CU's queue. */
+	submitted = client_stat_read(client, scu_s_cnt[cu_idx]);
+	completed = client_stat_read(client, scu_c_cnt[cu_idx]);
+	if (submitted == completed)
+		goto skip;
+
+	if (kds->xgq_enable) {
+		int wait_ms = 500;
+
+		xrt_cu_abort(scu_mgmt->xcus[cu_idx], client);
+
+		/* sub-device that handle command should do abort with a timeout */
+		do {
+			kds_warn(client, "%ld outstanding command(s) on SCU(%d)",
+				 submitted - completed, cu_idx);
+			msleep(wait_ms);
+			submitted = client_stat_read(client, scu_s_cnt[cu_idx]);
+			completed = client_stat_read(client, scu_c_cnt[cu_idx]);
+		} while (submitted != completed);
+
+		bad_state = xrt_cu_abort_done(scu_mgmt->xcus[cu_idx], client);
+	}
+
+	if (bad_state) {
+		kds->bad_state = 1;
+		kds_info(client, "CU(%d) hangs, please reset device", cu_idx);
+	}
+
+skip:
+	/* scu_mgmt->cu_refs is the critical section of multiple clients */
+	mutex_lock(&scu_mgmt->lock);
+	if (scu_mgmt->cu_refs[cu_idx] & CU_EXCLU_MASK)
+		scu_mgmt->cu_refs[cu_idx] = 0;
+	else
+		--scu_mgmt->cu_refs[cu_idx];
+	mutex_unlock(&scu_mgmt->lock);
+
+	return 0;
+}
+
+static int kds_ucu_release(struct inode *inode, struct file *filp)
+{
+	struct xrt_cu *xcu = filp->private_data;
+
+	xcu->user_manage_irq(xcu, false);
+	clear_bit(0, xcu->is_ucu);
+
+	return 0;
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 16, 0)
+static unsigned int kds_ucu_poll(struct file *filp, poll_table *wait)
+{
+	unsigned int ret = 0;
+#else
+static __poll_t kds_ucu_poll(struct file *filp, poll_table *wait)
+{
+	__poll_t ret = 0;
+#endif
+	struct xrt_cu *xcu = filp->private_data;
+
+	poll_wait(filp, &xcu->ucu_waitq, wait);
+
+	if (atomic_read(&xcu->ucu_event) > 0)
+		ret = POLLIN;
+
+	return ret;
+}
+
+static ssize_t kds_ucu_read(struct file *filp, char __user *buf,
+			    size_t count, loff_t *ppos)
+{
+	struct xrt_cu *xcu = filp->private_data;
+	ssize_t ret = 0;
+	s32 events = 0;
+
+	if (count != sizeof(s32))
+		return -EINVAL;
+
+	ret = wait_event_interruptible(xcu->ucu_waitq,
+				       (atomic_read(&xcu->ucu_event) > 0));
+	if (ret)
+		return ret;
+
+	events = atomic_xchg(&xcu->ucu_event, 0);
+	if (copy_to_user(buf, &events, count))
+		return -EFAULT;
+
+	return sizeof(events);
+}
+
+static ssize_t kds_ucu_write(struct file *filp, const char __user *buf,
+			     size_t count, loff_t *ppos)
+{
+	struct xrt_cu *xcu = filp->private_data;
+	s32 enable;
+
+	if (count != sizeof(s32))
+		return -EINVAL;
+
+	if (copy_from_user(&enable, buf, count))
+		return -EFAULT;
+
+	if (!xcu->configure_irq)
+		return -EOPNOTSUPP;
+	xcu->configure_irq(xcu, enable);
+
+	return sizeof(s32);
+}
+
+static const struct file_operations ucu_fops = {
+	.release	= kds_ucu_release,
+	.poll		= kds_ucu_poll,
+	.read		= kds_ucu_read,
+	.write		= kds_ucu_write,
+	.llseek		= noop_llseek,
+};
+
+int kds_open_ucu(struct kds_sched *kds, struct kds_client *client, u32 cu_idx)
+{
+	int fd;
+	struct kds_cu_mgmt *cu_mgmt;
+	struct xrt_cu *xcu;
+
+	cu_mgmt = &kds->cu_mgmt;
+	if ((cu_idx >= MAX_CUS) || (!cu_mgmt->xcus[cu_idx])) {
+		kds_err(client, "CU(%d) not found", cu_idx);
+		return -EINVAL;
+	}
+
+	if (!test_bit(cu_idx, client->cu_bitmap)) {
+		kds_err(client, "cu(%d) isn't reserved\n", cu_idx);
+		return -EINVAL;
+	}
+
+	mutex_lock(&cu_mgmt->lock);
+	if (!(cu_mgmt->cu_refs[cu_idx] & CU_EXCLU_MASK)) {
+		kds_err(client, "cu(%d) isn't exclusively reserved\n", cu_idx);
+		mutex_unlock(&cu_mgmt->lock);
+		return -EINVAL;
+	}
+	mutex_unlock(&cu_mgmt->lock);
+
+	xcu = cu_mgmt->xcus[cu_idx];
+	if (!client_stat_read(client, s_cnt[cu_idx])) {
+		set_bit(0, xcu->is_ucu);
+		if (client_stat_read(client, s_cnt[cu_idx])) {
+			clear_bit(0, xcu->is_ucu);
+			return -EBUSY;
+		}
+	}
+
+	if (!xcu->user_manage_irq)
+		return -EOPNOTSUPP;
+
+	if (xcu->user_manage_irq(xcu, true))
+		return -EINVAL;
+
+	init_waitqueue_head(&cu_mgmt->xcus[cu_idx]->ucu_waitq);
+	atomic_set(&cu_mgmt->xcus[cu_idx]->ucu_event, 0);
+	fd = anon_inode_getfd("[user_manage_cu]", &ucu_fops,
+			      cu_mgmt->xcus[cu_idx], O_RDWR);
+
+	return fd;
+}
+
+int kds_init_sched(struct kds_sched *kds)
+{
+	int i;
+
+	for (i = 0; i < MAX_CUS; i++) {
+		kds->cu_mgmt.xcus[i] = NULL;
+		kds->scu_mgmt.xcus[i] = NULL;
+	}
+	kds->cu_mgmt.cu_stats = alloc_percpu(struct cu_stats);
+	if (!kds->cu_mgmt.cu_stats)
+		return -ENOMEM;
+
+	kds->scu_mgmt.cu_stats = alloc_percpu(struct cu_stats);
+	if (!kds->scu_mgmt.cu_stats)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&kds->clients);
+	INIT_LIST_HEAD(&kds->alive_cus);
+	mutex_init(&kds->lock);
+	mutex_init(&kds->cu_mgmt.lock);
+	mutex_init(&kds->scu_mgmt.lock);
+	kds->num_client = 0;
+	kds->bad_state = 0;
+	/* At this point, I don't know if ERT subdev exist or not */
+	kds->ert_disable = true;
+	kds->ini_disable = false;
+	init_completion(&kds->comp);
+	init_waitqueue_head(&kds->wait_queue);
+
+	return 0;
+}
+
+void kds_fini_sched(struct kds_sched *kds)
+{
+	mutex_destroy(&kds->lock);
+	mutex_destroy(&kds->cu_mgmt.lock);
+
+	free_percpu(kds->cu_mgmt.cu_stats);
+}
+
+struct kds_command *kds_alloc_command(struct kds_client *client, u32 size)
+{
+	struct kds_command *xcmd;
+
+	xcmd = kzalloc(sizeof(struct kds_command), GFP_KERNEL);
+	if (!xcmd)
+		return NULL;
+
+	xcmd->client = client;
+	xcmd->type = 0;
+	xcmd->cu_idx = NO_INDEX;
+	xcmd->opcode = OP_NONE;
+	xcmd->status = KDS_NEW;
+	xcmd->timestamp_enabled = 0;
+
+	if (size == 0)
+		goto done;
+
+	xcmd->info = kzalloc(size, GFP_KERNEL);
+	if (!xcmd->info) {
+		kfree(xcmd);
+		return NULL;
+	}
+	xcmd->isize = size;
+	xcmd->payload_alloc = 1;
+
+done:
+	return xcmd;
+}
+
+void kds_free_command(struct kds_command *xcmd)
+{
+	if (!xcmd)
+		return;
+
+	if (xcmd->payload_alloc)
+		kfree(xcmd->info);
+	kfree(xcmd);
+}
+
+int kds_add_command(struct kds_sched *kds, struct kds_command *xcmd)
+{
+	struct kds_client *client = xcmd->client;
+	int err = 0;
+
+	BUG_ON(!xcmd->cb.notify_host);
+	BUG_ON(!xcmd->cb.free);
+
+	/* TODO: Check if command is blocked */
+	
+	/* Command is good to submit */
+	switch (xcmd->type) {
+	case KDS_CU:
+		err = kds_submit_cu(kds, xcmd);
+		break;
+	case KDS_SCU:
+		err = kds_submit_scu(kds, xcmd);
+		break;
+	case KDS_ERT:
+		err = kds_submit_ert(kds, xcmd);
+		break;
+	default:
+		kds_err(client, "Unknown type");
+		err = -EINVAL;
+	}
+	if (err) {
+		xcmd->cb.notify_host(xcmd, KDS_ERROR);
+		xcmd->cb.free(xcmd);
+	}
+	return err;
+}
+
+int kds_submit_cmd_and_wait(struct kds_sched *kds, struct kds_command *xcmd)
+{
+	struct kds_client *client = xcmd->client;
+	int ret = 0;
+
+	ret = kds_add_command(kds, xcmd);
+	if (ret)
+		return ret;
+
+	/* Why not wait_for_completion_interruptible_timeout()?
+	 * This is the process to configure ERT. If user ctrl-c, ERT will be
+	 * mark as in bad status and need reset device to recovery from it.
+	 * But ERT is actually alive.
+	 * To avoid this, wait for few seconds for ERT to complete command.
+	 */
+	ret = wait_for_completion_timeout(&kds->comp, msecs_to_jiffies(3000));
+	if (!ret) {
+		kds->ert->abort_sync(kds->ert, client, NO_INDEX);
+		/* ERT abort would handle command in time. The command would be
+		 * marked as ABORT or TIMEOUT and kds->comp would increase.
+		 * It is a  bug if below waiting never finished.
+		 */
+		wait_for_completion(&kds->comp);
+	}
+
+	return 0;
+}
+
+int kds_init_client(struct kds_sched *kds, struct kds_client *client)
+{
+	client->stats = alloc_percpu(struct client_stats);
+	if (!client->stats)
+		return -ENOMEM;
+
+	client->pid = get_pid(task_pid(current));
+	mutex_init(&client->lock);
+
+	init_waitqueue_head(&client->waitq);
+	atomic_set(&client->event, 0);
+
+	mutex_lock(&kds->lock);
+	list_add_tail(&client->link, &kds->clients);
+	kds->num_client++;
+	mutex_unlock(&kds->lock);
+
+	return 0;
+}
+
+/* This function returns true if the given CU/SCU belongs to the current slot
+ * per the kds context argument.
+ */
+static bool
+is_cu_in_ctx_slot(struct kds_sched *kds, struct kds_client_ctx *cctx, u32 bit, u32 cu_domain)
+{
+	struct xrt_cu *xcu = NULL;
+
+	if (cu_domain == (SCU_DOMAIN>>16))
+		xcu = kds->scu_mgmt.xcus[bit];
+	else
+		xcu = kds->cu_mgmt.xcus[bit];
+
+	if (xcu && (xcu->info.slot_idx == cctx->slot_idx))
+		return true;
+
+	return false;
+}
+
+static inline void
+_kds_fini_client(struct kds_sched *kds, struct kds_client *client,
+		 struct kds_client_ctx *cctx)
+{
+	struct kds_ctx_info info;
+	u32 bit;
+
+	kds_info(client, "Client pid(%d) has %d opening context for %d slot",
+		 pid_nr(client->pid), cctx->num_ctx, cctx->slot_idx);
+
+	mutex_lock(&client->lock);
+	while (cctx->virt_cu_ref) {
+		info.cu_idx = CU_CTX_VIRT_CU;
+		info.curr_ctx = cctx;
+		info.cu_domain = 0;
+		kds_del_context(kds, client, &info);
+	}
+
+	bit = find_first_bit(client->scu_bitmap, MAX_CUS);
+	while (bit < MAX_CUS) {
+		/* Check whether this SCU belongs to current slot */
+	        if (is_cu_in_ctx_slot(kds, cctx, bit, (SCU_DOMAIN>>16))) {
+			info.cu_idx = bit;
+			info.cu_domain = (SCU_DOMAIN>>16);
+			info.curr_ctx = cctx;
+			kds_del_context(kds, client, &info);
+		}
+		kds_info(client,"Removing CU Domain[%d] CU Index [%d]",info.cu_domain,info.cu_idx);
+		bit = find_next_bit(client->scu_bitmap, MAX_CUS, bit + 1);
+	};
+	bitmap_zero(client->scu_bitmap, MAX_CUS);
+	bit = find_first_bit(client->cu_bitmap, MAX_CUS);
+	while (bit < MAX_CUS) {
+		/* Check whether this CU belongs to current slot */
+	        if (is_cu_in_ctx_slot(kds, cctx, bit, 0 /* regular CUs */)) {
+			info.cu_idx = bit;
+			info.cu_domain = 0;
+			info.curr_ctx = cctx;
+			kds_del_context(kds, client, &info);
+		}
+		kds_info(client,"Removing CU Domain[%d] CU Index [%d]",info.cu_domain,info.cu_idx);
+		bit = find_next_bit(client->cu_bitmap, MAX_CUS, bit + 1);
+	};
+	bitmap_zero(client->cu_bitmap, MAX_CUS);
+	mutex_unlock(&client->lock);
+
+	WARN_ON(cctx->num_ctx);
+}
+
+void kds_fini_client(struct kds_sched *kds, struct kds_client *client)
+{
+	struct kds_client_ctx *curr;
+
+        list_for_each_entry(curr, &client->ctx_list, link) {
+		/* Release client's resources */
+		if (curr->num_ctx)
+			_kds_fini_client(kds, client, curr);
+        }
+
+	put_pid(client->pid);
+	mutex_destroy(&client->lock);
+
+	mutex_lock(&kds->lock);
+	list_del(&client->link);
+	kds->num_client--;
+	mutex_unlock(&kds->lock);
+
+	free_percpu(client->stats);
+}
+
+int kds_add_context(struct kds_sched *kds, struct kds_client *client,
+		    struct kds_ctx_info *info)
+{
+	u32 cu_idx = info->cu_idx;
+	bool shared = (info->flags != CU_CTX_EXCLUSIVE);
+	struct kds_client_ctx *cctx = (struct kds_client_ctx *)info->curr_ctx;
+	int i;
+
+	BUG_ON(!mutex_is_locked(&client->lock));
+
+	if (!cctx)
+		return -EINVAL;
+
+	/* TODO: In lagcy KDS, there is a concept of implicit CUs.
+	 * It looks like that part is related to cdma. But it use the same
+	 * cu bit map and it relies on to how user open context.
+	 * Let's consider that kind of CUs later.
+	 */
+	if (cu_idx == CU_CTX_VIRT_CU) {
+		if (!shared) {
+			kds_err(client, "Only allow share virtual CU");
+			return -EINVAL;
+		}
+		/* a special handling for m2m cu :( */
+		/* SAIF TODO */
+		if (kds->cu_mgmt.num_cdma && !cctx->virt_cu_ref) {
+			i = kds->cu_mgmt.num_cus - kds->cu_mgmt.num_cdma;
+			test_and_set_bit(i, client->cu_bitmap);
+			mutex_lock(&kds->cu_mgmt.lock);
+			++kds->cu_mgmt.cu_refs[i];
+			mutex_unlock(&kds->cu_mgmt.lock);
+		}
+		++cctx->virt_cu_ref;
+	} else {
+	     if (info->cu_domain == (SCU_DOMAIN>>16)) {
+		if (kds_add_scu_context(kds, client, info))
+			return -EINVAL;
+	     } else {
+		if (kds_add_cu_context(kds, client, info))
+			return -EINVAL;
+	     }
+	}
+
+	++cctx->num_ctx;
+	kds_info(client, "Client pid(%d) add context Domain(%d) CU(0x%x) shared(%s)",
+		 pid_nr(client->pid), info->cu_domain, cu_idx, shared? "true" : "false");
+	return 0;
+}
+
+int kds_del_context(struct kds_sched *kds, struct kds_client *client,
+		    struct kds_ctx_info *info)
+{
+	u32 cu_idx = info->cu_idx;
+	struct kds_client_ctx *cctx = (struct kds_client_ctx *)info->curr_ctx;
+	int i;
+
+	BUG_ON(!mutex_is_locked(&client->lock));
+
+	if (!cctx)
+		return -EINVAL;
+	if (cu_idx == CU_CTX_VIRT_CU) {
+		if (!cctx->virt_cu_ref) {
+			kds_err(client, "No opening virtual CU");
+			return -EINVAL;
+		}
+		--cctx->virt_cu_ref;
+		/* a special handling for m2m cu :( */
+		/* SAIF TODO */
+		if (kds->cu_mgmt.num_cdma && !cctx->virt_cu_ref) {
+			i = kds->cu_mgmt.num_cus - kds->cu_mgmt.num_cdma;
+			if (!test_and_clear_bit(i, client->cu_bitmap)) {
+				kds_err(client, "never reserved cmda");
+				return -EINVAL;
+			}
+			mutex_lock(&kds->cu_mgmt.lock);
+			--kds->cu_mgmt.cu_refs[i];
+			mutex_unlock(&kds->cu_mgmt.lock);
+		}
+	} else {
+	     if (info->cu_domain == (SCU_DOMAIN>>16)) {
+		if (kds_del_scu_context(kds, client, info))
+			return -EINVAL;
+	     } else {
+		if (kds_del_cu_context(kds, client, info))
+			return -EINVAL;
+	     }
+	}
+
+	--cctx->num_ctx;
+	kds_info(client, "Client pid(%d) del context Domain(%d) CU(0x%x)",
+		 pid_nr(client->pid), info->cu_domain, cu_idx);
+	return 0;
+}
+
+int kds_map_cu_addr(struct kds_sched *kds, struct kds_client *client,
+		    int idx, unsigned long size, u32 *addrp)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+
+	BUG_ON(!mutex_is_locked(&client->lock));
+	if ((idx >= MAX_CUS) || (!cu_mgmt->xcus[idx])) {
+		kds_err(client, "cu(%d) out of range\n", idx);
+		return -EINVAL;
+	}
+
+	if (!test_bit(idx, client->cu_bitmap)) {
+		kds_err(client, "cu(%d) isn't reserved\n", idx);
+		return -EINVAL;
+	}
+
+	mutex_lock(&cu_mgmt->lock);
+	/* WORKAROUND: If rw_shared is true, allow map shared CU */
+	if (!cu_mgmt->rw_shared && !(cu_mgmt->cu_refs[idx] & CU_EXCLU_MASK)) {
+		kds_err(client, "cu(%d) isn't exclusively reserved\n", idx);
+		mutex_unlock(&cu_mgmt->lock);
+		return -EINVAL;
+	}
+	mutex_unlock(&cu_mgmt->lock);
+
+	*addrp = kds_get_cu_addr(kds, idx);
+
+	return 0;
+}
+
+static inline void
+insert_cu(struct kds_cu_mgmt *cu_mgmt, int i, struct xrt_cu *xcu)
+{
+	cu_mgmt->xcus[i] = xcu;
+	/* m2m cu */
+	if (xcu->info.intr_id == M2M_CU_ID)
+		cu_mgmt->num_cdma++;
+}
+
+int kds_add_cu(struct kds_sched *kds, struct xrt_cu *xcu)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	int i;
+
+	if (cu_mgmt->num_cus >= MAX_CUS)
+		return -ENOMEM;
+
+	/* 
+	 * For multi slot sorting CUs are not possible. We will find a free slot and
+	 * assign the CUs to that.
+	 */
+
+	/* Get a free slot in kds for this CU */
+	for (i = 0; i < MAX_CUS; i++) {
+		if (cu_mgmt->xcus[i] == NULL) {
+			insert_cu(cu_mgmt, i, xcu);
+			++cu_mgmt->num_cus;
+			list_add_tail(&xcu->cu, &kds->alive_cus);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+int kds_del_cu(struct kds_sched *kds, struct xrt_cu *xcu)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	int i;
+
+	if (cu_mgmt->num_cus == 0)
+		return -EINVAL;
+
+	for (i = 0; i < MAX_CUS; i++) {
+		if (cu_mgmt->xcus[i] != xcu)
+			continue;
+
+		cu_mgmt->xcus[i] = NULL;
+		cu_mgmt->cu_intr[i] = 0;
+		--cu_mgmt->num_cus;
+		list_del(&xcu->cu);
+		cu_stat_write(cu_mgmt, usage[i], 0);
+		break;
+	}
+
+	/* m2m cu */
+	if (xcu->info.intr_id == M2M_CU_ID)
+		cu_mgmt->num_cdma--;
+
+	return 0;
+}
+
+int kds_add_scu(struct kds_sched *kds, struct xrt_cu *xcu)
+{
+	struct kds_scu_mgmt *scu_mgmt = &kds->scu_mgmt;
+	int i;
+
+	if (xcu->info.cu_idx >= MAX_CUS)
+		return -EINVAL;
+
+	/* Get a free slot in kds for this CU */
+	for (i = 0; i < MAX_CUS; i++) {
+		if (scu_mgmt->xcus[i] == NULL) {
+			scu_mgmt->xcus[i] = xcu;
+			xcu->info.cu_idx = i;
+			++scu_mgmt->num_cus;
+
+			list_add_tail(&xcu->cu, &kds->alive_cus);
+			return 0;
+		}
+	}
+
+	return -ENOSPC;
+}
+
+int kds_del_scu(struct kds_sched *kds, struct xrt_cu *xcu)
+{
+	struct kds_scu_mgmt *scu_mgmt = &kds->scu_mgmt;
+	int i = 0;
+
+	if (scu_mgmt->num_cus == 0)
+		return -EINVAL;
+
+	for (i = 0; i < MAX_CUS; i++) {
+		if (scu_mgmt->xcus[i] != xcu)
+			continue;
+
+		scu_mgmt->xcus[i] = NULL;
+		--scu_mgmt->num_cus;
+		list_del(&xcu->cu);
+		cu_stat_write(scu_mgmt, usage[i], 0);
+		break;
+	}
+
+	return 0;
+}
+
+/* Do not use this function when xclbin can be changed */
+int kds_get_cu_total(struct kds_sched *kds)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+
+	return cu_mgmt->num_cus;
+}
+
+/* Do not use this function when xclbin can be changed */
+u32 kds_get_cu_addr(struct kds_sched *kds, int idx)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+
+	return cu_mgmt->xcus[idx]->info.addr;
+}
+
+/* Do not use this function when xclbin can be changed */
+u32 kds_get_cu_proto(struct kds_sched *kds, int idx)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+
+	return cu_mgmt->xcus[idx]->info.protocol;
+}
+
+int kds_get_max_regmap_size(struct kds_sched *kds)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	int size;
+	int max_size = 0;
+	int i;
+
+	for (i = 0; i < MAX_CUS; i++) {
+		if (!cu_mgmt->xcus[i])
+			continue;
+
+		size = xrt_cu_regmap_size(cu_mgmt->xcus[i]);
+		if (max_size < size)
+			max_size = size;
+	}
+
+	return max_size;
+}
+
+static void ert_dummy_submit(struct kds_ert *ert, struct kds_command *xcmd)
+{
+	kds_err(xcmd->client, "ert submit op not implemented\n");
+	return;
+}
+
+static void ert_dummy_abort(struct kds_ert *ert, struct kds_client *client, int cu_idx)
+{
+	kds_err(client, "ert abort op not implemented\n");
+	return;
+}
+
+static bool ert_dummy_abort_done(struct kds_ert *ert, struct kds_client *client, int cu_idx)
+{
+	kds_err(client, "ert abort_done op not implemented\n");
+	return false;
+}
+
+int kds_init_ert(struct kds_sched *kds, struct kds_ert *ert)
+{
+	kds->ert = ert;
+	/* By default enable ERT if it exist */
+	kds->ert_disable = false;
+
+	if (!ert->submit)
+		ert->submit = ert_dummy_submit;
+
+	if (!ert->abort)
+		ert->abort = ert_dummy_abort;
+
+	if (!ert->abort_done)
+		ert->abort_done = ert_dummy_abort_done;
+
+	return 0;
+}
+
+int kds_fini_ert(struct kds_sched *kds)
+{
+	kds->ert_disable = true;
+	kds->ert = NULL;
+	return 0;
+}
+
+void kds_reset(struct kds_sched *kds)
+{
+	kds->bad_state = 0;
+	kds->ini_disable = false;
+
+	if (!kds->ert)
+		kds->ert_disable = true;
+
+	if (kds->polling_thread && !IS_ERR(kds->polling_thread)) {
+		kds->polling_stop = 1;
+		wake_up_interruptible(&kds->wait_queue);
+		(void) kthread_stop(kds->polling_thread);
+		kds->polling_thread = NULL;
+	}
+}
+
+static int kds_fa_assign_cmdmem(struct kds_sched *kds)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	u32 total_sz = 0;
+	u32 num_slots;
+	u32 size;
+	u64 bar_addr;
+	u64 dev_addr;
+	int ret = 0;
+	int i;
+	void __iomem *vaddr;
+
+	for (i = 0; i < MAX_CUS; i++) {
+		if (!cu_mgmt->xcus[i])
+			continue;
+
+		if (!xrt_is_fa(cu_mgmt->xcus[i], &size))
+			continue;
+
+		total_sz += size;
+		/* Release old resoruces if exist */
+		xrt_fa_cfg_update(cu_mgmt->xcus[i], 0, 0, 0, 0);
+	}
+
+	total_sz = round_up_to_next_power2(total_sz);
+
+	if (kds->cmdmem.size < total_sz)
+		return -EINVAL;
+
+	num_slots = kds->cmdmem.size / total_sz;
+
+	bar_addr = kds->cmdmem.bar_paddr;
+	dev_addr = kds->cmdmem.dev_paddr;
+	vaddr = kds->cmdmem.vaddr;
+	for (i = 0; i < MAX_CUS; i++) {
+		if (!cu_mgmt->xcus[i])
+			continue;
+
+		if (!xrt_is_fa(cu_mgmt->xcus[i], &size))
+			continue;
+
+		/* The updated FA CU would release when it is removed */
+		ret = xrt_fa_cfg_update(cu_mgmt->xcus[i], bar_addr, dev_addr, vaddr, num_slots);
+		if (ret)
+			return ret;
+		bar_addr += (u64)size * num_slots;
+		dev_addr += (u64)size * num_slots;
+		vaddr += (u64)size * num_slots;
+	}
+
+	return 0;
+}
+
+int kds_cfg_update(struct kds_sched *kds)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	struct xrt_cu *xcu;
+	int ret = 0;
+	int i;
+
+	/* Update PLRAM CU */
+	if (kds->cmdmem.bo) {
+		ret = kds_fa_assign_cmdmem(kds);
+		if (ret)
+			return -EINVAL;
+		/* ERT doesn't understand Fast adapter
+		 * Host crash at around configure command if ERT is enabled.
+		 * TODO: Support fast adapter in ERT?
+		 */
+		kds->ert_disable = true;
+	}
+
+	/* Update CU interrupt mode */
+	if (kds->cu_intr_cap) {
+		//run polling thread if there is any cu without interrupt support
+		for (i = 0; i < MAX_CUS; i++) {
+			xcu = cu_mgmt->xcus[i];
+			if (!xcu)
+				continue;
+			if (!xcu->info.intr_enable) {
+				u32 cu_idx = xcu->info.cu_idx;
+
+				kds->cu_intr = false;
+				xcu_info(xcu, "CU(%d) doesnt support interrupt, running polling thread for all cus", cu_idx);
+				goto run_polling;
+			}
+		}
+
+		for (i = 0; i < MAX_CUS; i++) {
+			xcu = cu_mgmt->xcus[i];
+			if (!xcu)
+				continue;
+
+			if (cu_mgmt->cu_intr[i] == KDS_SETTING(kds->cu_intr))
+				continue;
+
+			ret = xrt_cu_cfg_update(xcu, KDS_SETTING(kds->cu_intr));
+			if (!ret)
+				cu_mgmt->cu_intr[i] = KDS_SETTING(kds->cu_intr);
+			else if (ret == -ENOSYS) {
+				/* CU doesn't support interrupt */
+				cu_mgmt->cu_intr[i] = 0;
+				ret = 0;
+			}
+		}
+	}
+
+run_polling:
+	if (!KDS_SETTING(kds->cu_intr) && !kds->polling_thread) {
+		kds->polling_stop = 0;
+		kds->polling_thread = kthread_run(kds_polling_thread, kds, "kds_poll");
+		if (IS_ERR(kds->polling_thread)) {
+			ret = IS_ERR(kds->polling_thread);
+			kds->polling_thread = NULL;
+		}
+	}
+
+	return ret;
+}
+
+void kds_cus_irq_enable(struct kds_sched *kds, bool enable)
+{
+	struct kds_cu_mgmt *cu_mgmt = &kds->cu_mgmt;
+	struct xrt_cu *xcu = NULL;
+	int i;
+
+	for (i = 0; i < MAX_CUS; i++) {
+		xcu = cu_mgmt->xcus[i];
+		if (!xcu)
+			continue;
+
+		if (!xcu->info.intr_enable)
+			continue;
+
+		xcu->configure_irq(xcu, enable);
+	}
+}
+
+int is_bad_state(struct kds_sched *kds)
+{
+	return kds->bad_state;
+}
+
+u32 kds_live_clients(struct kds_sched *kds, pid_t **plist)
+{
+	u32 count = 0;
+
+	mutex_lock(&kds->lock);
+	count = kds_live_clients_nolock(kds, plist);
+	mutex_unlock(&kds->lock);
+
+	return count;
+}
+
+/*
+ * Return number of client with open ("live") contexts on CUs.
+ * If this number > 0, xclbin is locked down.
+ * If plist is non-NULL, the list of PIDs of live clients will also be returned.
+ * Note that plist should be freed by caller.
+ */
+u32 kds_live_clients_nolock(struct kds_sched *kds, pid_t **plist)
+{
+	const struct list_head *ptr;
+	struct kds_client *client;
+	struct kds_client_ctx *curr;
+	pid_t *pl = NULL;
+	u32 count = 0;
+	u32 i = 0;
+
+	/* Find out number of active client */
+	list_for_each(ptr, &kds->clients) {
+		client = list_entry(ptr, struct kds_client, link);
+		list_for_each_entry(curr, &client->ctx_list, link) {
+			if (curr->num_ctx > 0)
+			count++;
+		}
+	}
+	if (count == 0 || plist == NULL)
+		goto out;
+
+	/* Collect list of PIDs of active client */
+	pl = (pid_t *)vmalloc(sizeof(pid_t) * count);
+	if (pl == NULL)
+		goto out;
+
+	list_for_each(ptr, &kds->clients) {
+		client = list_entry(ptr, struct kds_client, link);
+		list_for_each_entry(curr, &client->ctx_list, link) {
+			if (curr->num_ctx > 0) {
+				pl[i] = pid_nr(client->pid);
+				i++;
+			}
+		}
+	}
+
+	*plist = pl;
+out:
+	return count;
+}
+
+/*
+ * This function would parse ip_layout and return a sorted CU info array.
+ * But ip_layout only provides a portion of CU info. The caller would need to
+ * fetch and fill the missing info.
+ *
+ * This function determines CU indexing for all supported platforms.
+ */
+int kds_ip_layout2cu_info(struct ip_layout *ip_layout,
+			 struct xrt_cu_info cu_info[], int num_info)
+{
+	struct xrt_cu_info info = { 0 };
+	struct ip_data *ip;
+	char kname[64] = { 0 };
+	char *kname_p = NULL;
+	int num_cus = 0;
+	int i = 0, j = 0;
+
+	for(i = 0; i < ip_layout->m_count; ++i) {
+		ip = &ip_layout->m_ip_data[i];
+
+		if (ip->m_type != IP_KERNEL)
+			continue;
+
+		if ((~ip->m_base_address) == 0)
+			continue;
+
+		memset(&info, 0, sizeof(info));
+
+		/* ip_data->m_name format "<kernel name>:<instance name>",
+		 * where instance name is so called CU name.
+		 */
+		strncpy(kname, ip->m_name, sizeof(kname));
+		kname[sizeof(kname)-1] = '\0';
+		kname_p = &kname[0];
+		strncpy(info.kname, strsep(&kname_p, ":"), sizeof(info.kname));
+		info.kname[sizeof(info.kname)-1] = '\0';
+		strncpy(info.iname, strsep(&kname_p, ":"), sizeof(info.iname));
+		info.iname[sizeof(info.kname)-1] = '\0';
+
+		info.addr = ip->m_base_address;
+		info.intr_enable = ip->properties & IP_INT_ENABLE_MASK;
+		info.protocol = (ip->properties & IP_CONTROL_MASK) >> IP_CONTROL_SHIFT;
+		info.intr_id = (ip->properties & IP_INTERRUPT_ID_MASK) >> IP_INTERRUPT_ID_SHIFT;
+
+		/* Rules to determine CUs ordering:
+		 * Sort CU in interrupt ID increase order.
+		 * If interrupt ID is the same, sort CU in address increase order.
+		 * This strategy is good for both legacy xclbin and latest xclbin.
+		 *
+		 * - For legacy xclbin, all of the interrupt IDs are 0. The
+		 * interrupt is wiring by CU address increase order.
+		 * - For latest xclbin, the interrupt ID is from 0 ~ 127.
+		 *   -- One exception is if only 1 CU, the interrupt ID would be 1.
+		 *
+		 * With below insertion sort algorithm, we don't need to check
+		 * if xclbin is legacy or latest.
+		 */
+
+		/* Insertion sort */
+		for (j = num_cus; j >= 0; j--) {
+			struct xrt_cu_info *prev_info;
+
+			if (j == 0) {
+				memcpy(&cu_info[j], &info, sizeof(info));
+				cu_info[j].cu_idx = j;
+				num_cus++;
+				break;
+			}
+
+			prev_info = &cu_info[j-1];
+			if (prev_info->intr_id < info.intr_id) {
+				memcpy(&cu_info[j], &info, sizeof(info));
+				cu_info[j].cu_idx = j;
+				num_cus++;
+				break;
+			} else if (prev_info->intr_id > info.intr_id) {
+				memcpy(&cu_info[j], prev_info, sizeof(info));
+				cu_info[j].cu_idx = j;
+				continue;
+			}
+
+			/* Same interrupt ID case. Sorted by address */
+			if (prev_info->addr < info.addr) {
+				memcpy(&cu_info[j], &info, sizeof(info));
+				cu_info[j].cu_idx = j;
+				num_cus++;
+				break;
+			} else if (prev_info->addr > info.addr) {
+				memcpy(&cu_info[j], prev_info, sizeof(info));
+				cu_info[j].cu_idx = j;
+				continue;
+			}
+			/*
+			 * Same CU address? Something wrong in the ip_layout.
+			 * But I will just ignore this IP and not error out.
+			 */
+			break;
+		}
+	}
+
+	return num_cus;
+}
+
+/*
+ * This function would parse ip_layout and return a sorted CU info array.
+ * But ip_layout only provides a portion of CU info. The caller would need to
+ * fetch and fill the missing info.
+ *
+ * This function determines CU indexing for all supported platforms.
+ */
+int kds_ip_layout2scu_info(struct ip_layout *ip_layout, struct xrt_cu_info cu_info[], int num_info)
+{
+	struct xrt_cu_info info = {0};
+	struct ip_data *ip;
+	char kname[64] = {0};
+	char *kname_p = NULL;
+	int num_cus = 0;
+	int i = 0;
+
+	for(i = 0; i < ip_layout->m_count; ++i) {
+		ip = &ip_layout->m_ip_data[i];
+
+		if (ip->m_type != IP_PS_KERNEL)
+			continue;
+
+		memset(&info, 0, sizeof(info));
+
+		/* ip_data->m_name format "<kernel name>:<instance name>",
+		 * where instance name is so called CU name.
+		 */
+		strncpy(kname, ip->m_name, sizeof(kname));
+		kname[sizeof(kname)-1] = '\0';
+		kname_p = &kname[0];
+		strncpy(info.kname, strsep(&kname_p, ":"), sizeof(info.kname));
+		info.kname[sizeof(info.kname)-1] = '\0';
+		strncpy(info.iname, strsep(&kname_p, ":"), sizeof(info.iname));
+		info.iname[sizeof(info.kname)-1] = '\0';
+
+		info.addr = 0;
+		info.intr_enable = 0;
+		info.protocol = CTRL_HS;
+		info.intr_id = 0;
+
+		memcpy(&cu_info[num_cus], &info, sizeof(info));
+		cu_info[num_cus].cu_idx = num_cus;
+		num_cus++;
+	}
+
+	return num_cus;
+}
+
+/* User space execbuf command related functions below */
+void cfg_ecmd2xcmd(struct ert_configure_cmd *ecmd,
+		   struct kds_command *xcmd)
+{
+	int i;
+
+	/* To let ERT 3.0 firmware aware new KDS is talking to it,
+	 * set kds_30 bit. This is no harm for ERT 2.0 firmware.
+	 */
+	ecmd->kds_30 = 1;
+
+	xcmd->opcode = OP_CONFIG;
+
+	xcmd->execbuf = (u32 *)ecmd;
+
+	xcmd->isize = ecmd->num_cus * sizeof(u32);
+	/* Remove encoding at the low bits
+	 * The same information is stored in CU already.
+	 */
+	for (i = 0; i < ecmd->num_cus; i++)
+		ecmd->data[i] &= ~0x000000FF;
+
+	/* Expect a ordered list of CU address */
+	memcpy(xcmd->info, ecmd->data, xcmd->isize);
+}
+
+void start_skrnl_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd)
+{
+	xcmd->opcode = OP_START_SK;
+
+	xcmd->execbuf = (u32 *)ecmd;
+	if (ecmd->stat_enabled) {
+		xcmd->timestamp_enabled = 1;
+		set_xcmd_timestamp(xcmd, KDS_NEW);
+	}
+
+	xcmd->cu_mask[0] = ecmd->cu_mask;
+	memcpy(&xcmd->cu_mask[1], ecmd->data, ecmd->extra_cu_masks);
+	xcmd->num_mask = 1 + ecmd->extra_cu_masks;
+
+	xcmd->isize = (ecmd->count - xcmd->num_mask) * sizeof(u32);
+	memcpy(xcmd->info, &ecmd->data[ecmd->extra_cu_masks], xcmd->isize);
+	ecmd->type = ERT_SCU;
+}
+
+void start_krnl_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd)
+{
+	xcmd->opcode = OP_START;
+
+	xcmd->execbuf = (u32 *)ecmd;
+	if (ecmd->stat_enabled) {
+		xcmd->timestamp_enabled = 1;
+		set_xcmd_timestamp(xcmd, KDS_NEW);
+	}
+
+	xcmd->cu_mask[0] = ecmd->cu_mask;
+	memcpy(&xcmd->cu_mask[1], ecmd->data, ecmd->extra_cu_masks);
+	xcmd->num_mask = 1 + ecmd->extra_cu_masks;
+
+	/* Copy resigter map into info and isize is the size of info in bytes.
+	 *
+	 * Based on ert.h, ecmd->count is the number of words following header.
+	 * In ert_start_kernel_cmd, the CU register map size is
+	 * (count - (1 + extra_cu_masks)) and I would like to Skip
+	 * first 4 control registers
+	 */
+	xcmd->isize = (ecmd->count - xcmd->num_mask - 4) * sizeof(u32);
+	memcpy(xcmd->info, &ecmd->data[4 + ecmd->extra_cu_masks], xcmd->isize);
+	xcmd->payload_type = REGMAP;
+	ecmd->type = ERT_CU;
+}
+
+void start_krnl_kv_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			     struct kds_command *xcmd)
+{
+	xcmd->opcode = OP_START;
+
+	xcmd->execbuf = (u32 *)ecmd;
+	if (ecmd->stat_enabled) {
+		xcmd->timestamp_enabled = 1;
+		set_xcmd_timestamp(xcmd, KDS_NEW);
+	}
+
+	xcmd->cu_mask[0] = ecmd->cu_mask;
+	memcpy(&xcmd->cu_mask[1], ecmd->data, ecmd->extra_cu_masks);
+	xcmd->num_mask = 1 + ecmd->extra_cu_masks;
+
+	/* Copy resigter map into info and isize is the size of info in bytes.
+	 *
+	 * Based on ert.h, ecmd->count is the number of words following header.
+	 * In ert_start_kernel_cmd, the CU register map size is
+	 * (count - (1 + extra_cu_masks)).
+	 */
+	xcmd->isize = (ecmd->count - xcmd->num_mask) * sizeof(u32);
+	memcpy(xcmd->info, &ecmd->data[ecmd->extra_cu_masks], xcmd->isize);
+	xcmd->payload_type = KEY_VAL;
+	ecmd->type = ERT_CU;
+}
+
+void start_fa_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd)
+{
+	xcmd->opcode = OP_START;
+
+	xcmd->execbuf = (u32 *)ecmd;
+	if (ecmd->stat_enabled) {
+		xcmd->timestamp_enabled = 1;
+		set_xcmd_timestamp(xcmd, KDS_NEW);
+	}
+
+	xcmd->cu_mask[0] = ecmd->cu_mask;
+	memcpy(&xcmd->cu_mask[1], ecmd->data, ecmd->extra_cu_masks);
+	xcmd->num_mask = 1 + ecmd->extra_cu_masks;
+
+	/* Copy descriptor into info and isize is the size of info in bytes.
+	 *
+	 * Based on ert.h, ecmd->count is the number of words following header.
+	 * The descriptor size is (count - (1 + extra_cu_masks)).
+	 */
+	xcmd->isize = (ecmd->count - xcmd->num_mask) * sizeof(u32);
+	memcpy(xcmd->info, &ecmd->data[ecmd->extra_cu_masks], xcmd->isize);
+	ecmd->type = ERT_CTRL;
+}
+
+void abort_ecmd2xcmd(struct ert_abort_cmd *ecmd, struct kds_command *xcmd)
+{
+	u32 *exec_bo_handle = xcmd->info;
+
+	xcmd->opcode = OP_ABORT;
+	*exec_bo_handle = ecmd->exec_bo_handle;
+}
+
+void set_xcmd_timestamp(struct kds_command *xcmd, enum kds_status s)
+{
+	if (!xcmd->timestamp_enabled)
+		return;
+
+	xcmd->timestamp[s] = ktime_to_ns(ktime_get());
+}
+
+/**
+ * cu_mask_to_cu_idx - Convert CU mask to CU index list
+ *
+ * @xcmd: Command
+ * @cus:  CU index list
+ *
+ * Returns: Number of CUs
+ *
+ */
+inline int
+cu_mask_to_cu_idx(struct kds_command *xcmd, uint8_t *cus)
+{
+	int num_cu = 0;
+	u32 mask;
+	/* i for iterate masks, j for iterate bits */
+	int i, j;
+
+	for (i = 0; i < xcmd->num_mask; ++i) {
+		if (xcmd->cu_mask[i] == 0)
+			continue;
+
+		mask = xcmd->cu_mask[i];
+		for (j = 0; mask > 0; ++j) {
+			if (!(mask & 0x1)) {
+				mask >>= 1;
+				continue;
+			}
+
+			cus[num_cu] = i * 32 + j;
+			num_cu++;
+			mask >>= 1;
+		}
+	}
+
+	return num_cu;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/xgq_execbuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/xgq_execbuf.c
@@ -0,0 +1,105 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General
+ Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/string.h>
+#include "xocl_drv.h"
+#include "xgq_execbuf.h"
+#include "xrt_cu.h"
+
+/* return the size of the xgq start cu command */
+int xgq_exec_convert_start_cu_cmd(struct xgq_cmd_start_cuidx *xgq_cmd,
+					struct ert_start_kernel_cmd *ecmd)
+{
+	int num_mask = 0;
+	int payload_size = 0;
+
+	num_mask = 1 + ecmd->extra_cu_masks;
+	payload_size = (ecmd->count - num_mask - 4) * sizeof(u32);
+	memcpy(xgq_cmd->data, &ecmd->data[4 + ecmd->extra_cu_masks], payload_size);
+
+	xgq_cmd->hdr.opcode = XGQ_CMD_OP_START_CUIDX;
+	xgq_cmd->hdr.state = 1;
+	xgq_cmd->hdr.count = payload_size;
+
+	return sizeof(xgq_cmd->hdr) + payload_size;
+}
+
+/* return the size of the xgq start cu command for ps kernel */
+int xgq_exec_convert_start_scu_cmd(struct xgq_cmd_start_cuidx *xgq_cmd,
+					struct ert_start_kernel_cmd *ecmd)
+{
+	int num_mask = 0;
+	int payload_size = 0;
+
+	num_mask = 1 + ecmd->extra_cu_masks;
+	payload_size = (ecmd->count - num_mask) * sizeof(u32);
+	memcpy(xgq_cmd->data, &ecmd->data[0], payload_size);
+
+	xgq_cmd->hdr.opcode = XGQ_CMD_OP_START_CUIDX;
+	xgq_cmd->hdr.state = 1;
+	xgq_cmd->hdr.count = payload_size;
+	xgq_cmd->hdr.cu_domain = (SCU_DOMAIN>>16);
+
+	return sizeof(xgq_cmd->hdr) + payload_size;
+}
+
+int xgq_exec_convert_start_kv_cu_cmd(struct xgq_cmd_start_cuidx *xgq_cmd,
+				     struct ert_start_kernel_cmd *ecmd)
+{
+	int num_mask = 0;
+	int payload_size = 0;
+
+	num_mask = 1 + ecmd->extra_cu_masks;
+	payload_size = (ecmd->count - num_mask) * sizeof(u32);
+	memcpy(xgq_cmd->data, &ecmd->data[ecmd->extra_cu_masks], payload_size);
+
+	xgq_cmd->hdr.opcode = XGQ_CMD_OP_START_CUIDX_KV;
+	xgq_cmd->hdr.state = 1;
+	xgq_cmd->hdr.count = payload_size;
+
+	return sizeof(xgq_cmd->hdr) + payload_size;
+}
+
+/* return the size of the xgq clock calibration command */
+int xgq_exec_convert_clock_calib_cmd(struct xgq_cmd_clock_calib *xgq_cmd,
+					struct ert_packet *ecmd)
+{
+
+	xgq_cmd->hdr.opcode = XGQ_CMD_OP_CLOCK_CALIB;
+	xgq_cmd->hdr.state = 1;
+	xgq_cmd->hdr.count = ecmd->count * sizeof(u32);
+
+	return sizeof(xgq_cmd->hdr) + xgq_cmd->hdr.count;
+}
+
+/* return the size of the xgq accessibility command */
+int xgq_exec_convert_accessible_cmd(struct xgq_cmd_access_valid *xgq_cmd,
+					struct ert_packet *ecmd)
+{
+	xgq_cmd->hdr.opcode = XGQ_CMD_OP_ACCESS_VALID;
+	xgq_cmd->hdr.state = 1;
+	xgq_cmd->hdr.count = ecmd->count * sizeof(u32);
+
+	return sizeof(xgq_cmd->hdr) + xgq_cmd->hdr.count;
+}
+
+/* return the size of the xgq data integrity command */
+int xgq_exec_convert_data_integrity_cmd(struct xgq_cmd_data_integrity *xgq_cmd,
+					struct ert_packet *ecmd)
+{
+	xgq_cmd->hdr.opcode = XGQ_CMD_OP_DATA_INTEGRITY;
+	xgq_cmd->hdr.state = 1;
+	xgq_cmd->hdr.count = ecmd->count * sizeof(u32);
+
+	return sizeof(struct xgq_cmd_data_integrity);	
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/xrt_cu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/xrt_cu.c
@@ -0,0 +1,883 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Unify CU Model
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/delay.h>
+#include "kds_client.h"
+#include "xrt_cu.h"
+
+inline void xrt_cu_circ_produce(struct xrt_cu *xcu, u32 stage, uintptr_t cmd)
+{
+	unsigned long head = xcu->crc_buf.head;
+	unsigned long tail = xcu->crc_buf.tail;
+	struct xrt_cu_log *item;
+
+	if (!xcu->debug)
+		return;
+
+	/* Will overwrite oldest data if buffer is full */
+	item = (struct xrt_cu_log *)&xcu->crc_buf.buf[head];
+	item->stage = stage;
+	item->cmd_id = cmd;
+	item->ts = ktime_to_ns(ktime_get());
+
+	if (CIRC_SPACE(head, tail, CIRC_BUF_SIZE) < sizeof(struct xrt_cu_log)) {
+		tail += sizeof(struct xrt_cu_log);
+		if (tail >= CIRC_BUF_SIZE)
+			tail = 0;
+	}
+
+	head += sizeof(struct xrt_cu_log);
+	if (head >= CIRC_BUF_SIZE)
+		head = 0;
+
+	xcu->crc_buf.head = head;
+	xcu->crc_buf.tail = tail;
+}
+
+ssize_t xrt_cu_circ_consume_all(struct xrt_cu *xcu, char *buf, size_t size)
+{
+	unsigned long head = xcu->crc_buf.head;
+	unsigned long tail = xcu->crc_buf.tail;
+	size_t cnt = CIRC_CNT(head, tail, CIRC_BUF_SIZE);
+	/* return min(count to the end of buffer, CIRC_CNT()) */
+	size_t cnt_to_end = CIRC_CNT_TO_END(head, tail, CIRC_BUF_SIZE);
+	size_t nread = 0;
+
+	if (size < cnt)
+		nread = size;
+	else
+		nread = cnt;
+
+	if (nread <= cnt_to_end) {
+		memcpy(buf, xcu->crc_buf.buf + tail, nread);
+		xcu->crc_buf.tail += nread;
+	} else {
+		/* Needs two times of copy */
+		memcpy(buf, xcu->crc_buf.buf + tail, cnt_to_end);
+		memcpy(buf + cnt_to_end, xcu->crc_buf.buf, nread - cnt_to_end);
+		xcu->crc_buf.tail = nread - cnt_to_end;
+	}
+
+	return nread;
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)
+static void cu_timer(unsigned long data)
+{
+	struct xrt_cu *xcu = (struct xrt_cu *)data;
+#else
+static void cu_timer(struct timer_list *t)
+{
+	struct xrt_cu *xcu = from_timer(xcu, t, timer);
+#endif
+
+	xcu_dbg(xcu, "%s tick\n", xcu->info.iname);
+
+	atomic_inc(&xcu->tick);
+
+	mod_timer(&xcu->timer, jiffies + CU_TIMER);
+}
+
+static inline struct kds_client *
+first_event_client_or_null(struct xrt_cu *xcu)
+{
+	struct kds_client *curr = NULL;
+
+	if (list_empty(&xcu->events))
+		return NULL;
+
+	mutex_lock(&xcu->ev_lock);
+	if (list_empty(&xcu->events))
+		goto done;
+
+	curr = list_first_entry(&xcu->events, struct kds_client, ev_entry);
+
+done:
+	mutex_unlock(&xcu->ev_lock);
+	return curr;
+}
+
+static inline void
+move_to_queue(struct kds_command *xcmd, struct list_head *dst_q, u32 *dst_len)
+{
+	if (dst_q)
+		list_move_tail(&xcmd->list, dst_q);
+	++(*dst_len);
+}
+
+static bool abort_client(struct kds_command *xcmd, void *cond)
+{
+	void *client = cond;
+
+	return (xcmd->client == client)? true : false;
+}
+
+static bool abort_handle(struct kds_command *xcmd, void *cond)
+{
+	u32 handle = *(u32 *)cond;
+
+	return (xcmd->exec_bo_handle == handle)? true : false;
+}
+
+/**
+ * process_cq() - Process completed queue
+ * @xcu: Target XRT CU
+ */
+static inline void process_cq(struct xrt_cu *xcu)
+{
+	struct kds_command *xcmd;
+
+	if (!xcu->num_cq)
+		return;
+
+	/* Notify host and free command
+	 *
+	 * NOTE: Use loop to handle completed commands could improve
+	 * performance (Reduce sleep time and increase chance for more
+	 * pending commands at one time)
+	 */
+	while (xcu->num_cq) {
+		xcmd = list_first_entry(&xcu->cq, struct kds_command, list);
+		set_xcmd_timestamp(xcmd, xcmd->status);
+		xrt_cu_circ_produce(xcu, CU_LOG_STAGE_CQ, (uintptr_t)xcmd);
+		xcmd->cb.notify_host(xcmd, xcmd->status);
+		list_del(&xcmd->list);
+		xcmd->cb.free(xcmd);
+		--xcu->num_cq;
+		xcu->cu_stat.usage++;
+	}
+}
+
+/**
+ * __process_sq() - Process submitted queue
+ * @xcu: Target XRT CU
+ */
+static inline void __process_sq(struct xrt_cu *xcu)
+{
+	struct kds_command *xcmd;
+	struct kds_client *ev_client = NULL;
+	unsigned int tick;
+
+	/* CU is ready to accept more commands
+	 * Return credits to allow submit more commands
+	 */
+	if (xcu->ready_cnt) {
+		xrt_cu_put_credit(xcu, xcu->ready_cnt);
+		xcu->ready_cnt = 0;
+	}
+
+	/* Sometimes a CU done but it doesn't ready for new command.
+	 * In this case, sq could be empty.
+	 */
+	if (!xcu->num_sq)
+		return;
+
+	ev_client = first_event_client_or_null(xcu);
+	if (unlikely(ev_client)) {
+		tick = atomic_read(&xcu->tick);
+		if (xcu->start_tick == 0) {
+			xcu->start_tick = tick;
+			goto get_complete_and_out;
+		}
+
+		if (tick - xcu->start_tick < CU_EXEC_DEFAULT_TTL)
+			goto get_complete_and_out;
+
+		if (xrt_cu_cmd_abort(xcu, ev_client, abort_client))
+			xcu->bad_state = true;
+
+		xcu->start_tick = 0;
+	}
+
+get_complete_and_out:
+	xcmd = xrt_cu_get_complete(xcu);
+	while (xcmd) {
+		xrt_cu_circ_produce(xcu, CU_LOG_STAGE_SQ, (uintptr_t)xcmd);
+		move_to_queue(xcmd, &xcu->cq, &xcu->num_cq);
+		--xcu->num_sq;
+		xcmd = xrt_cu_get_complete(xcu);
+	}
+}
+
+/**
+ * process_sq() - Process submitted queue
+ * @xcu: Target XRT CU
+ */
+static inline void process_sq(struct xrt_cu *xcu)
+{
+	/* A submitted command might be done but the CU is still
+	 * not ready for next command. In this case, check CU status
+	 * to get ready count.
+	 */
+	if (!xcu->num_sq && !is_zero_credit(xcu))
+		return;
+
+	/* If no command is running on the hardware,
+	 * this would not really access hardware.
+	 */
+	xrt_cu_check(xcu);
+
+	__process_sq(xcu);
+}
+
+/**
+ * process_rq() - Process run queue
+ * @xcu: Target XRT CU
+ *
+ * Return: return 0 if run queue is empty or no credit
+ *	   Otherwise, return 1
+ */
+static inline int process_rq(struct xrt_cu *xcu)
+{
+	struct kds_command *xcmd;
+	struct kds_client *ev_client;
+	struct list_head *dst_q;
+	int *dst_len;
+
+	if (!xcu->num_rq)
+		return 0;
+
+	xcmd = list_first_entry(&xcu->rq, struct kds_command, list);
+
+	ev_client = first_event_client_or_null(xcu);
+	if (unlikely(xcu->bad_state || (ev_client == xcmd->client))) {
+		xcmd->status = KDS_ABORT;
+		dst_q = &xcu->cq;
+		dst_len = &xcu->num_cq;
+		goto move_cmd;
+	}
+
+	if (!xrt_cu_get_credit(xcu))
+		return 0;
+
+	/* if successfully get credit, you must start cu */
+	if (xrt_cu_submit_config(xcu, xcmd)) {
+		xrt_cu_put_credit(xcu, 1);
+		return 0;
+	}
+	xrt_cu_start(xcu);
+	set_xcmd_timestamp(xcmd, KDS_RUNNING);
+	xrt_cu_circ_produce(xcu, CU_LOG_STAGE_RQ, (uintptr_t)xcmd);
+
+	dst_q = NULL;
+	dst_len = &xcu->num_sq;
+	/* ktime_get_* is still heavy. This impact ~20% of IOPS on echo mode.
+	 * For some sort of CU, which usually has a relative long execute time,
+	 * we could hide this overhead and provide timestamp for each command.
+	 * But this implementation is used for general purpose. Please create CU
+	 * specific thread if needed.
+	 */
+	//xcmd->start = ktime_get_raw_fast_ns();
+move_cmd:
+	move_to_queue(xcmd, dst_q, dst_len);
+	--xcu->num_rq;
+
+	return 1;
+}
+
+/**
+ * process_pq() - Process pending queue
+ * @xcu: Target XRT CU
+ *
+ * Move all of the pending queue commands to the tail of run queue
+ * and re-initialized pending queue
+ */
+static inline void process_pq(struct xrt_cu *xcu)
+{
+	unsigned long flags;
+
+	/* Get pending queue command number without lock.
+	 * The idea is to reduce the possibility of conflict on lock.
+	 * Need to check pending command number again after lock.
+	 */
+	if (!xcu->num_pq)
+		return;
+	spin_lock_irqsave(&xcu->pq_lock, flags);
+	if (xcu->num_pq) {
+		list_splice_tail_init(&xcu->pq, &xcu->rq);
+		xcu->num_rq += xcu->num_pq;
+		xcu->num_pq = 0;
+	}
+	spin_unlock_irqrestore(&xcu->pq_lock, flags);
+	if (xcu->max_running < xcu->num_rq)
+		xcu->max_running = xcu->num_rq;
+}
+
+static inline void
+try_abort_cmd(struct xrt_cu *xcu, struct kds_command *abort_cmd)
+{
+	struct kds_command *xcmd;
+	struct kds_command *tmp;
+	u32 handle;
+
+	/* Never call this function on the performance critical path */
+	handle = *(u32 *)abort_cmd->info;
+	list_for_each_entry_safe(xcmd, tmp, &xcu->rq, list) {
+		if (xcmd->exec_bo_handle != handle)
+			continue;
+
+		/* Found the xcmd to abort! */
+		abort_cmd->status = KDS_COMPLETED;
+
+		xcu_info(xcu, "Abort command(%d) on running queue", handle);
+		xcmd->status = KDS_ABORT;
+		move_to_queue(xcmd, &xcu->cq, &xcu->num_cq);
+		--xcu->num_rq;
+		return;
+	}
+
+	if (!xcu->num_sq)
+		return;
+
+	if (xrt_cu_cmd_abort(xcu, &handle, abort_handle)) {
+		xcu->bad_state = true;
+		abort_cmd->status = KDS_TIMEOUT;
+	} else {
+		abort_cmd->status = KDS_COMPLETED;
+	}
+
+	xcmd = xrt_cu_get_complete(xcu);
+	while (xcmd) {
+		move_to_queue(xcmd, &xcu->cq, &xcu->num_cq);
+		--xcu->num_sq;
+		xcmd = xrt_cu_get_complete(xcu);
+	}
+}
+
+/**
+ * process_hpq() - Process high priority queue
+ * @xcu: Target XRT CU
+ *
+ */
+static inline void process_hpq(struct xrt_cu *xcu)
+{
+	struct kds_command *xcmd;
+	struct kds_command *tmp;
+	unsigned long flags;
+
+	if (!xcu->num_hpq)
+		return;
+
+	/* slowpath */
+	spin_lock_irqsave(&xcu->hpq_lock, flags);
+	if (!xcu->num_hpq)
+		goto done;
+
+	list_for_each_entry_safe(xcmd, tmp, &xcu->hpq, list) {
+		if (xcmd->opcode == OP_ABORT)
+			try_abort_cmd(xcu, xcmd);
+
+		list_del(&xcmd->list);
+		--xcu->num_hpq;
+	}
+
+done:
+	spin_unlock_irqrestore(&xcu->hpq_lock, flags);
+	complete(&xcu->comp);
+}
+
+int xrt_cu_process_queues(struct xrt_cu *xcu)
+{
+	/* Move pending commands to running queue */
+	process_pq(xcu);
+
+	/* Make sure to submit as many commands as possible */
+	while (process_rq(xcu));
+
+	/* process completed queue before submitted queue, for
+	 * two reasons:
+	 * - The last submitted command may be still running
+	 * - while handling completed queue, running command might done
+	 * - process_sq will check CU status, which is thru slow bus
+	 */
+	process_cq(xcu);
+	process_sq(xcu);
+
+	/* process rare commands with very high priority. For example
+	 * abort command.
+	 * If this kind of command don't not exist, this would be a very
+	 * low overhead and should not impact performance.
+	 * But if this kind of command exist, this would be a slow path.
+	 */
+	process_hpq(xcu);
+
+	if (xcu->num_rq || xcu->num_sq || xcu->num_cq)
+		return XCU_BUSY;
+
+	return XCU_IDLE;
+}
+
+int xrt_cu_intr_thread(void *data)
+{
+	struct xrt_cu *xcu = (struct xrt_cu *)data;
+	int ret = 0;
+	int loop_cnt = 0;
+
+	xcu_info(xcu, "CU[%d] start", xcu->info.cu_idx);
+	mod_timer(&xcu->timer, jiffies + CU_TIMER);
+	xrt_cu_enable_intr(xcu, CU_INTR_DONE | CU_INTR_READY);
+	while (!xcu->stop) {
+		/* Make sure to submit as many commands as possible.
+		 * This is why we call continue here. This is important to make
+		 * CU busy, especially CU has hardware queue.
+		 */
+		if (process_rq(xcu))
+			continue;
+
+		if (xcu->num_sq || is_zero_credit(xcu)) {
+			xrt_cu_check(xcu);
+			if (!xcu->done_cnt || !xcu->ready_cnt) {
+				xcu->sleep_cnt++;
+				/* Don't use down_interruptible() here.
+				 * If CU hang, this thread would keep waiting.
+				 * Host application is not able to exit since
+				 * there are outstading commands.
+				 *
+				 * CU_TIMER is runing at low frequence. For
+				 * normal CU, it will unlikely timeout.
+				 */
+				if (down_timeout(&xcu->sem_cu, CU_TIMER))
+					ret = -ERESTARTSYS;
+				xrt_cu_check(xcu);
+			}
+			__process_sq(xcu);
+		}
+
+		process_cq(xcu);
+		process_hpq(xcu);
+
+		/* Avoid large num_rq leads to more 120 sec blocking */
+		if (++loop_cnt == 8) {
+			loop_cnt = 0;
+			schedule();
+		}
+
+		/* Continue until run queue empty */
+		if (xcu->num_rq)
+			continue;
+
+		if (!xcu->num_sq && !xcu->num_cq) {
+			loop_cnt = 0;
+			/* Record CU status before sleep */
+			if (!xcu->num_pq)
+				xrt_cu_check_force(xcu);
+			if (down_interruptible(&xcu->sem))
+				ret = -ERESTARTSYS;
+		}
+
+		process_pq(xcu);
+	}
+	xrt_cu_disable_intr(xcu, CU_INTR_DONE | CU_INTR_READY);
+	del_timer_sync(&xcu->timer);
+
+	if (xcu->bad_state)
+		ret = -EBUSY;
+
+	xcu_info(xcu, "CU[%d] thread end, bad state %d\n",
+		 xcu->info.cu_idx, xcu->bad_state);
+	return ret;
+}
+
+void xrt_cu_submit(struct xrt_cu *xcu, struct kds_command *xcmd)
+{
+	unsigned long flags;
+	bool first_command = false;
+
+	/* Add command to pending queue
+	 * wakeup CU thread if it is the first command
+	 */
+	spin_lock_irqsave(&xcu->pq_lock, flags);
+	list_add_tail(&xcmd->list, &xcu->pq);
+	++xcu->num_pq;
+	first_command = (xcu->num_pq == 1);
+	spin_unlock_irqrestore(&xcu->pq_lock, flags);
+	if (first_command)
+		up(&xcu->sem);
+}
+
+void xrt_cu_hpq_submit(struct xrt_cu *xcu, struct kds_command *xcmd)
+{
+	unsigned long flags;
+
+	/* This high priority queue is designed to handle those hight priority
+	 * but low frequency commands. Like abort command.
+	 */
+	spin_lock_irqsave(&xcu->hpq_lock, flags);
+	list_add_tail(&xcmd->list, &xcu->hpq);
+	++xcu->num_hpq;
+	spin_unlock_irqrestore(&xcu->hpq_lock, flags);
+	up(&xcu->sem);
+
+	wait_for_completion(&xcu->comp);
+}
+
+/**
+ * xrt_cu_abort() - Set an abort event in the CU for client
+ * @xcu: Target XRT CU
+ * @client: The client tries to abort commands
+ *
+ * This is used to ask CU thread to abort all commands from the client.
+ */
+void xrt_cu_abort(struct xrt_cu *xcu, struct kds_client *client)
+{
+	struct kds_client *curr;
+
+	mutex_lock(&xcu->ev_lock);
+	if (list_empty(&xcu->events))
+		goto add_event;
+
+	/* avoid re-add the same client */
+	list_for_each_entry(curr, &xcu->events, ev_entry) {
+		if (client == curr)
+			goto done;
+	}
+
+add_event:
+	client->ev_type = EV_ABORT;
+	list_add_tail(&client->ev_entry, &xcu->events);
+done:
+	mutex_unlock(&xcu->ev_lock);
+}
+
+/**
+ * xrt_cu_abort_done() - Let CU know client asked abort is done
+ * @xcu: Target XRT CU
+ * @client: The client tries to abort commands
+ *
+ */
+bool xrt_cu_abort_done(struct xrt_cu *xcu, struct kds_client *client)
+{
+	struct kds_client *curr;
+	struct kds_client *next;
+
+	mutex_lock(&xcu->ev_lock);
+	if (list_empty(&xcu->events))
+		goto done;
+
+	list_for_each_entry_safe(curr, next, &xcu->events, ev_entry) {
+		if (client != curr)
+			continue;
+
+		list_del(&curr->ev_entry);
+		break;
+	}
+
+done:
+	mutex_unlock(&xcu->ev_lock);
+
+	return xcu->bad_state;
+}
+
+int xrt_cu_cfg_update(struct xrt_cu *xcu, int intr)
+{
+	int err = 0;
+
+	/* Check if CU support interrupt in hardware */
+	if (!xcu->info.intr_enable)
+		return -ENOSYS;
+
+	if (xrt_cu_get_protocol(xcu) == CTRL_NONE) {
+		xcu_warn(xcu, "Interrupt enabled value should be false for ap_ctrl_none cu\n");
+		return -ENOSYS;
+	}
+
+	if (xcu->thread) {
+		/* Stop old thread */
+		xcu->stop = 1;
+		up(&xcu->sem_cu);
+		up(&xcu->sem);
+		if (!IS_ERR(xcu->thread))
+			(void) kthread_stop(xcu->thread);
+		xcu->thread = NULL;
+	}
+
+	if (!intr)
+		return 0;
+
+	/* launch new thread */
+	xcu->stop = 0;
+	sema_init(&xcu->sem, 0);
+	sema_init(&xcu->sem_cu, 0);
+	atomic_set(&xcu->tick, 0);
+	xcu->thread = kthread_run(xrt_cu_intr_thread, xcu, xcu->info.iname);
+	if (IS_ERR(xcu->thread)) {
+		err = IS_ERR(xcu->thread);
+		xcu->thread = NULL;
+		xcu_err(xcu, "Create CU thread failed, err %d\n", err);
+	}
+
+	return err;
+}
+
+/*
+ * If KDS has to manage PLRAM resources, we should come up with a better design.
+ * Ideally, CU subdevice should request for cmdmem resource instead of KDS assign
+ * cmdmem resource to CU.
+ * Or, another solution is to let KDS create CU subdevice indtead of
+ * icap/zocl_xclbin.
+ */
+static u32 cu_fa_get_desc_size(struct xrt_cu *xcu)
+{
+	struct xrt_cu_info *info = &xcu->info;
+	u32 size = sizeof(descriptor_t);
+	int i;
+
+	for (i = 0; i < info->num_args; i++) {
+		/* The "nextDescriptorAddr" argument is a fast adapter argument.
+		 * It is not required to construct descriptor
+		 */
+		if (!strcmp(info->args[i].name, "nextDescriptorAddr") || !info->args[i].size)
+			continue;
+
+		size += (sizeof(descEntry_t)+info->args[i].size);
+	}
+
+	return round_up_to_next_power2(size);
+}
+
+int xrt_is_fa(struct xrt_cu *xcu, u32 *size)
+{
+	struct xrt_cu_info *info = &xcu->info;
+	int ret;
+
+	ret = (info->model == XCU_FA)? 1 : 0;
+
+	if (ret && size)
+		*size = cu_fa_get_desc_size(xcu);
+
+	return ret;
+}
+
+int xrt_fa_cfg_update(struct xrt_cu *xcu, u64 bar, u64 dev, void __iomem *vaddr, u32 num_slots)
+{
+	struct xrt_cu_fa *cu_fa = xcu->core;
+	u32 slot_size;
+
+	if (bar == 0) {
+		cu_fa->cmdmem = NULL;
+		cu_fa->paddr = 0;
+		cu_fa->slot_sz = 0;
+		cu_fa->num_slots = 0;
+		return 0;
+	}
+
+	slot_size = cu_fa_get_desc_size(xcu);
+
+	cu_fa->cmdmem = vaddr;
+	cu_fa->paddr = dev;
+	cu_fa->slot_sz = slot_size;
+	cu_fa->num_slots = num_slots;
+
+	cu_fa->credits = (cu_fa->num_slots < cu_fa->max_credits)?
+			 cu_fa->num_slots : cu_fa->max_credits;
+
+	return 0;
+}
+
+int xrt_cu_get_protocol(struct xrt_cu *xcu)
+{
+	return xcu->info.protocol;
+}
+
+u32 xrt_cu_get_status(struct xrt_cu *xcu)
+{
+	return xcu->status;
+}
+
+int xrt_cu_regmap_size(struct xrt_cu *xcu)
+{
+	int max_off_idx = 0;
+	int max_off = 0;
+	int i;
+
+	if (!xcu->info.num_args)
+		return xcu->info.size;
+
+	/* Max regmap size is max offset + register size */
+	for (i = 0; i < xcu->info.num_args; i++) {
+		if (max_off < xcu->info.args[i].offset) {
+			max_off = xcu->info.args[i].offset;
+			max_off_idx = i;
+		}
+	}
+
+	return max_off + xcu->info.args[max_off_idx].size;
+}
+
+int xrt_cu_init(struct xrt_cu *xcu)
+{
+	int err = 0;
+	char *name = xcu->info.iname;
+
+	/* TODO A workaround to avoid m2m subdev launch thread */
+	if (!strlen(name))
+		return 0;
+
+	/* Use list for driver space command queue
+	 * Should we consider ring buffer?
+	 */
+
+	/* Initialize pending queue and lock */
+	INIT_LIST_HEAD(&xcu->pq);
+	spin_lock_init(&xcu->pq_lock);
+	/* Initialize run queue */
+	INIT_LIST_HEAD(&xcu->rq);
+	/* Initialize completed queue */
+	INIT_LIST_HEAD(&xcu->cq);
+
+	mutex_init(&xcu->ev_lock);
+	INIT_LIST_HEAD(&xcu->events);
+	sema_init(&xcu->sem, 0);
+	sema_init(&xcu->sem_cu, 0);
+
+	INIT_LIST_HEAD(&xcu->hpq);
+	spin_lock_init(&xcu->hpq_lock);
+	init_completion(&xcu->comp);
+
+	xcu->crc_buf.head = 0;
+	xcu->crc_buf.tail = 0;
+	xcu->crc_buf.buf = xcu->log_buf;
+
+	memset(&xcu->cu_stat, 0, sizeof(struct per_custat));
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)
+	setup_timer(&xcu->timer, cu_timer, (unsigned long)xcu);
+#else
+	timer_setup(&xcu->timer, cu_timer, 0);
+#endif
+	atomic_set(&xcu->tick, 0);
+	xcu->start_tick = 0;
+	xcu->thread = NULL;
+
+	mod_timer(&xcu->timer, jiffies + CU_TIMER);
+	return err;
+}
+
+void xrt_cu_fini(struct xrt_cu *xcu)
+{
+	/* TODO A workaround for m2m subdev */
+	if (!strlen(xcu->info.iname))
+		return;
+
+	xcu->stop = 1;
+	up(&xcu->sem_cu);
+	up(&xcu->sem);
+	if (xcu->thread && !IS_ERR(xcu->thread))
+		(void) kthread_stop(xcu->thread);
+
+	del_timer_sync(&xcu->timer);
+	return;
+}
+
+ssize_t show_cu_stat(struct xrt_cu *xcu, char *buf)
+{
+	ssize_t sz = 0;
+
+	/* Add CU dynamic statistic information in below */
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Pending queue:    %d\n",
+			xcu->num_pq);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Running queue:    %d\n",
+			xcu->num_rq);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Submitted queue:  %d\n",
+			xcu->num_sq);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Completed queue:  %d\n",
+			xcu->num_cq);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Bad state:        %d\n",
+			xcu->bad_state);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Current credit:   %d\n",
+			xrt_cu_peek_credit(xcu));
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "CU status:        0x%x\n",
+			xcu->status);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "sleep cnt:        %d\n",
+			xcu->sleep_cnt);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "max running:      %d\n",
+			xcu->max_running);
+
+	if (xcu->info.model == XCU_FA) {
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, "-- FA CU specific --\n");
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Check count: %lld\n",
+				to_cu_fa(xcu->core)->check_count);
+	}
+
+	if (sz < PAGE_SIZE - 1)
+		buf[sz++] = 0;
+	else
+		buf[PAGE_SIZE - 1] = 0;
+
+	return sz;
+}
+
+ssize_t show_cu_info(struct xrt_cu *xcu, char *buf)
+{
+	struct xrt_cu_info *info = &xcu->info;
+	ssize_t sz = 0;
+	char dir[10];
+	int i;
+
+	/* Add any CU static information in below */
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Kernel name: %s\n",
+			info->kname);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Instance(CU) name: %s\n",
+			info->iname);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "CU address: 0x%llx\n",
+			info->addr);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "CU index: %d\n",
+			info->cu_idx);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Protocol: %s\n",
+			prot2str(info->protocol));
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Interrupt cap: %d\n",
+			info->intr_enable);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Interrupt ID:  %d\n",
+			info->intr_id);
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "SW Resettable: %d\n",
+			info->sw_reset);
+
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "--- Arguments ---\n");
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, "Number of arguments: %d\n",
+			info->num_args);
+	for (i = 0; i < info->num_args; i++) {
+		if (info->args[i].dir == DIR_INPUT)
+			strcpy(dir, "input");
+		else if (info->args[i].dir == DIR_OUTPUT)
+			strcpy(dir, "output");
+		else
+			strcpy(dir, "unknown");
+
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, "arg name: %s\n",
+				info->args[i].name);
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, "  size: %d\n",
+				info->args[i].size);
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, "  offset: 0x%x\n",
+				info->args[i].offset);
+		sz += scnprintf(buf+sz, PAGE_SIZE - sz, "  direction: %s\n",
+				dir);
+	}
+
+	if (sz < PAGE_SIZE - 1)
+		buf[sz++] = 0;
+	else
+		buf[PAGE_SIZE - 1] = 0;
+
+
+	return sz;
+}
+
+ssize_t show_formatted_cu_stat(struct xrt_cu *xcu, char *buf)
+{
+	ssize_t sz = 0;
+	char *fmt = "%lld %d\n";
+	int in_flight = xcu->num_sq;
+
+	sz += scnprintf(buf+sz, PAGE_SIZE - sz, fmt,
+			xcu->cu_stat.usage, in_flight);
+
+	return sz;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/common/xrt_xclbin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/common/xrt_xclbin.c
@@ -0,0 +1,311 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver XCLBIN parser
+ *
+ * Copyright (C) 2020-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: David Zhang <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <asm/errno.h>
+#include <linux/vmalloc.h>
+#include "xclbin.h"
+#include "xrt_xclbin.h"
+
+int xrt_xclbin_parse_header(const unsigned char *data,
+	unsigned int size, struct XHwIcap_Bit_Header *header)
+{
+	unsigned int i;
+	unsigned int len;
+	unsigned int tmp;
+	unsigned int index;
+
+	/* Start Index at start of bitstream */
+	index = 0;
+
+	/* Initialize HeaderLength.  If header returned early inidicates
+	 * failure.
+	 */
+	header->HeaderLength = XHI_BIT_HEADER_FAILURE;
+
+	/* Get "Magic" length */
+	header->MagicLength = data[index++];
+	header->MagicLength = (header->MagicLength << 8) | data[index++];
+
+	/* Read in "magic" */
+	for (i = 0; i < header->MagicLength - 1; i++) {
+		tmp = data[index++];
+		if (i%2 == 0 && tmp != XHI_EVEN_MAGIC_BYTE)
+			return -1;   /* INVALID_FILE_HEADER_ERROR */
+
+		if (i%2 == 1 && tmp != XHI_ODD_MAGIC_BYTE)
+			return -1;   /* INVALID_FILE_HEADER_ERROR */
+
+	}
+
+	/* Read null end of magic data. */
+	tmp = data[index++];
+
+	/* Read 0x01 (short) */
+	tmp = data[index++];
+	tmp = (tmp << 8) | data[index++];
+
+	/* Check the "0x01" half word */
+	if (tmp != 0x01)
+		return -1;	 /* INVALID_FILE_HEADER_ERROR */
+
+	/* Read 'a' */
+	tmp = data[index++];
+	if (tmp != 'a')
+		return -1;	  /* INVALID_FILE_HEADER_ERROR	*/
+
+	/* Get Design Name length */
+	len = data[index++];
+	len = (len << 8) | data[index++];
+
+	/* allocate space for design name and final null character. */
+	header->DesignName = vmalloc(len);
+
+	/* Read in Design Name */
+	for (i = 0; i < len; i++)
+		header->DesignName[i] = data[index++];
+
+
+	if (header->DesignName[len-1] != '\0')
+		return -1;
+
+	/* Read 'b' */
+	tmp = data[index++];
+	if (tmp != 'b')
+		return -1;	/* INVALID_FILE_HEADER_ERROR */
+
+	/* Get Part Name length */
+	len = data[index++];
+	len = (len << 8) | data[index++];
+
+	/* allocate space for part name and final null character. */
+	header->PartName = vmalloc(len);
+
+	/* Read in part name */
+	for (i = 0; i < len; i++)
+		header->PartName[i] = data[index++];
+
+	if (header->PartName[len-1] != '\0')
+		return -1;
+
+	/* Read 'c' */
+	tmp = data[index++];
+	if (tmp != 'c')
+		return -1;	/* INVALID_FILE_HEADER_ERROR */
+
+	/* Get date length */
+	len = data[index++];
+	len = (len << 8) | data[index++];
+
+	/* allocate space for date and final null character. */
+	header->Date = vmalloc(len);
+
+	/* Read in date name */
+	for (i = 0; i < len; i++)
+		header->Date[i] = data[index++];
+
+	if (header->Date[len - 1] != '\0')
+		return -1;
+
+	/* Read 'd' */
+	tmp = data[index++];
+	if (tmp != 'd')
+		return -1;	/* INVALID_FILE_HEADER_ERROR  */
+
+	/* Get time length */
+	len = data[index++];
+	len = (len << 8) | data[index++];
+
+	/* allocate space for time and final null character. */
+	header->Time = vmalloc(len);
+
+	/* Read in time name */
+	for (i = 0; i < len; i++)
+		header->Time[i] = data[index++];
+
+	if (header->Time[len - 1] != '\0')
+		return -1;
+
+	/* Read 'e' */
+	tmp = data[index++];
+	if (tmp != 'e')
+		return -1;	/* INVALID_FILE_HEADER_ERROR */
+
+	/* Get byte length of bitstream */
+	header->BitstreamLength = data[index++];
+	header->BitstreamLength = (header->BitstreamLength << 8) | data[index++];
+	header->BitstreamLength = (header->BitstreamLength << 8) | data[index++];
+	header->BitstreamLength = (header->BitstreamLength << 8) | data[index++];
+	header->HeaderLength = index;
+
+	return 0;
+}
+
+void
+xrt_xclbin_free_header(struct XHwIcap_Bit_Header *header)
+{
+	vfree(header->DesignName);
+	vfree(header->PartName);
+	vfree(header->Date);
+	vfree(header->Time);
+}
+
+char *
+xrt_xclbin_kind_to_string(enum axlf_section_kind kind)
+{
+	switch (kind) {
+	case BITSTREAM:  		return "BITSTREAM";
+	case CLEARING_BITSTREAM:  	return "CLEARING_BITSTREAM";
+	case EMBEDDED_METADATA:  	return "EMBEDDED_METADATA";
+	case FIRMWARE:  		return "FIRMWARE";
+	case DEBUG_DATA:  		return "DEBUG_DATA";
+	case SCHED_FIRMWARE:  		return "SCHED_FIRMWARE";
+	case MEM_TOPOLOGY:  		return "MEM_TOPOLOGY";
+	case CONNECTIVITY:  		return "CONNECTIVITY";
+	case IP_LAYOUT:  		return "IP_LAYOUT";
+	case DEBUG_IP_LAYOUT:  		return "DEBUG_IP_LAYOUT";
+	case DESIGN_CHECK_POINT: 	return "DESIGN_CHECK_POINT";
+	case CLOCK_FREQ_TOPOLOGY: 	return "CLOCK_FREQ_TOPOLOGY";
+	case MCS: 			return "MCS";
+	case BMC: 			return "BMC";
+	case BUILD_METADATA: 		return "BUILD_METADATA";
+	case KEYVALUE_METADATA: 	return "KEYVALUE_METADATA";
+	case USER_METADATA: 		return "USER_METADATA";
+	case DNA_CERTIFICATE: 		return "DNA_CERTIFICATE";
+	case PDI: 			return "PDI";
+	case BITSTREAM_PARTIAL_PDI: 	return "BITSTREAM_PARTIAL_PDI";
+	case PARTITION_METADATA: 	return "PARTITION_METADATA";
+	case EMULATION_DATA: 		return "EMULATION_DATA";
+	case SYSTEM_METADATA: 		return "SYSTEM_METADATA";
+	case SOFT_KERNEL: 		return "SOFT_KERNEL";
+	case ASK_FLASH: 		return "ASK_FLASH";
+	case AIE_METADATA: 		return "AIE_METADATA";
+	case ASK_GROUP_TOPOLOGY: 	return "ASK_GROUP_TOPOLOGY";
+	case ASK_GROUP_CONNECTIVITY: 	return "ASK_GROUP_CONNECTIVITY";
+	case SMARTNIC:			return "SMARTNIC";
+	case AIE_RESOURCES:		return "AIE_RESOURCES";
+	default: 			return "UNKNOWN";
+	}
+}
+
+const struct axlf_section_header *
+xrt_xclbin_get_section_hdr(const struct axlf *xclbin, enum axlf_section_kind kind)
+{
+	int i = 0;
+
+	/* Sanity check. */
+	if (xclbin->m_header.m_numSections > XCLBIN_MAX_NUM_SECTION)
+		return NULL;
+
+	for (i = 0; i < xclbin->m_header.m_numSections; i++) {
+		if (xclbin->m_sections[i].m_sectionKind == kind)
+			return &xclbin->m_sections[i];
+	}
+
+	return NULL;
+}
+
+int
+xrt_xclbin_check_section_hdr(const struct axlf_section_header *header,
+	uint64_t xclbin_len)
+{
+	return (header->m_sectionOffset + header->m_sectionSize) > xclbin_len ?
+		-EINVAL : 0;
+}
+
+int
+xrt_xclbin_section_info(const struct axlf *xclbin, enum axlf_section_kind kind,
+	uint64_t *offset, uint64_t *size)
+{
+	const struct axlf_section_header *memHeader = NULL;
+	uint64_t xclbin_len;
+	int err = 0;
+
+	memHeader = xrt_xclbin_get_section_hdr(xclbin, kind);
+	if (!memHeader)
+		return -EINVAL;
+
+	xclbin_len = xclbin->m_header.m_length;
+	err = xrt_xclbin_check_section_hdr(memHeader, xclbin_len);
+	if (err)
+		return err;
+
+	*offset = memHeader->m_sectionOffset;
+	*size = memHeader->m_sectionSize;
+
+	return 0;
+}
+
+struct axlf_section_header *
+xrt_xclbin_get_section_hdr_next(const struct axlf *xclbin,
+	enum axlf_section_kind kind, struct axlf_section_header *cur)
+{
+	int i;
+	int found = -1;
+	bool match = false;
+
+	for (i = 0; i < xclbin->m_header.m_numSections; i++) {
+		if (xclbin->m_sections[i].m_sectionKind == kind) {
+			if (match)
+				return (struct axlf_section_header *)&xclbin->m_sections[i];
+
+			if (&xclbin->m_sections[i] == cur) {
+				match = true;
+				found = -1;
+				continue;
+			} else
+				found = (found < 0 ? i : found);
+		}
+	}
+
+	if (found < 0)
+		return NULL;
+
+	return (struct axlf_section_header *)&xclbin->m_sections[found];
+}
+
+int xrt_xclbin_get_section_num(const struct axlf *xclbin,
+	enum axlf_section_kind kind)
+{
+	int i, cnt = 0;
+
+	for (i = 0; i < xclbin->m_header.m_numSections; i++) {
+		if (xclbin->m_sections[i].m_sectionKind == kind)
+			cnt++;
+	}
+
+	return cnt;
+}
+
+/* caller should free the allocated memory for **data */
+int xrt_xclbin_get_section(const struct axlf *xclbin,
+	enum axlf_section_kind kind, void **data, uint64_t *len)
+{
+	void *section = NULL;
+	int err = 0;
+	uint64_t offset = 0;
+	uint64_t size = 0;
+
+	err = xrt_xclbin_section_info(xclbin, kind, &offset, &size);
+	if (err)
+		return err;
+
+	section = vmalloc(size);
+	if (section == NULL)
+		return -ENOMEM;
+
+	memcpy(section, ((const char *)xclbin) + offset, size);
+
+	*data = section;
+	*len = size;
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/cu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/cu.c
@@ -0,0 +1,328 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "zocl_drv.h"
+#include "xrt_cu.h"
+
+#define IRQ_DISABLED 0
+
+struct zocl_cu {
+	struct xrt_cu		 base;
+	struct platform_device	*pdev;
+	u32			 irq;
+	char			*irq_name;
+	DECLARE_BITMAP(flag, 1);
+	spinlock_t		 lock;
+};
+
+static ssize_t debug_show(struct device *dev,
+	struct device_attribute *attr, char *buf)
+{
+#if 0
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_cu *cu = platform_get_drvdata(pdev);
+	struct xrt_cu *xcu = &cu->base;
+#endif
+	/* Place holder for now. */
+	return 0;
+}
+
+static ssize_t debug_store(struct device *dev,
+	struct device_attribute *da, const char *buf, size_t count)
+{
+#if 0
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_cu *cu = platform_get_drvdata(pdev);
+	struct xrt_cu *xcu = &cu->base;
+#endif
+
+	/* Place holder for now. */
+	return count;
+}
+static DEVICE_ATTR_RW(debug);
+
+static ssize_t
+cu_stat_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_cu *cu = platform_get_drvdata(pdev);
+
+	return show_cu_stat(&cu->base, buf);
+}
+static DEVICE_ATTR_RO(cu_stat);
+
+static ssize_t
+cu_info_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_cu *cu = platform_get_drvdata(pdev);
+
+	return show_cu_info(&cu->base, buf);
+}
+static DEVICE_ATTR_RO(cu_info);
+
+static ssize_t
+stat_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_cu *cu = platform_get_drvdata(pdev);
+
+	return show_formatted_cu_stat(&cu->base, buf);
+}
+static DEVICE_ATTR_RO(stat);
+
+static struct attribute *cu_attrs[] = {
+	&dev_attr_debug.attr,
+	&dev_attr_cu_stat.attr,
+	&dev_attr_cu_info.attr,
+	&dev_attr_stat.attr,
+	NULL,
+};
+
+static const struct attribute_group cu_attrgroup = {
+	.attrs = cu_attrs,
+};
+
+irqreturn_t cu_isr(int irq, void *arg)
+{
+	struct zocl_cu *zcu = arg;
+
+	xrt_cu_clear_intr(&zcu->base);
+
+	up(&zcu->base.sem_cu);
+
+	return IRQ_HANDLED;
+}
+
+irqreturn_t ucu_isr(int irq, void *arg)
+{
+	struct zocl_cu *zcu = arg;
+	unsigned long flags;
+
+	spin_lock_irqsave(&zcu->lock, flags);
+	atomic_inc(&zcu->base.ucu_event);
+
+	/* To handle level interrupt, have to disable this irq line.
+	 * We could esaily support edge interrupt if needed.
+	 * Like, provide one more gcu->flag to permanently enabl irq.
+	 */
+	if (!__test_and_set_bit(IRQ_DISABLED, zcu->flag))
+		disable_irq_nosync(irq);
+	spin_unlock_irqrestore(&zcu->lock, flags);
+
+	wake_up_interruptible(&zcu->base.ucu_waitq);
+
+	return IRQ_HANDLED;
+}
+
+static int user_manage_irq(struct xrt_cu *xcu, bool user_manage)
+{
+	struct zocl_cu *zcu = (struct zocl_cu *)xcu;
+	int ret;
+
+	if (xcu->info.intr_enable)
+		free_irq(zcu->irq, zcu);
+
+	/* Do not use IRQF_SHARED! */
+	if (user_manage)
+		ret = request_irq(zcu->irq, ucu_isr, 0, zcu->irq_name, zcu);
+	else
+		ret = request_irq(zcu->irq, cu_isr, 0, zcu->irq_name, zcu);
+	if (ret) {
+		DRM_INFO("%s: request_irq() failed\n", __func__);
+		return ret;
+	}
+
+	if (user_manage) {
+		__set_bit(IRQ_DISABLED, zcu->flag);
+		spin_lock_init(&zcu->lock);
+		disable_irq(zcu->irq);
+	}
+
+	return 0;
+}
+
+static int configure_irq(struct xrt_cu *xcu, bool enable)
+{
+	struct zocl_cu *zcu = (struct zocl_cu *)xcu;
+	unsigned long flags;
+
+	spin_lock_irqsave(&zcu->lock, flags);
+	if (enable) {
+		if (__test_and_clear_bit(IRQ_DISABLED, zcu->flag))
+			enable_irq(zcu->irq);
+	} else {
+		if (!__test_and_set_bit(IRQ_DISABLED, zcu->flag))
+			disable_irq(zcu->irq);
+	}
+	spin_unlock_irqrestore(&zcu->lock, flags);
+
+	return 0;
+}
+
+static int cu_probe(struct platform_device *pdev)
+{
+	struct zocl_cu *zcu;
+	struct resource **res;
+	struct xrt_cu_info *info;
+	struct drm_zocl_dev *zdev;
+	struct xrt_cu_arg *args = NULL;
+	int err = 0;
+	int i;
+
+	zcu = kzalloc(sizeof(*zcu), GFP_KERNEL);
+	if (!zcu)
+		return -ENOMEM;
+
+	zcu->pdev = pdev;
+	zcu->base.dev = &pdev->dev;
+
+	info = dev_get_platdata(&pdev->dev);
+	memcpy(&zcu->base.info, info, sizeof(struct xrt_cu_info));
+
+	res = vzalloc(sizeof(struct resource *) * info->num_res);
+	if (!res) {
+		err = -ENOMEM;
+		goto err;
+	}
+
+	for (i = 0; i < info->num_res; ++i) {
+		res[i] = platform_get_resource(pdev, IORESOURCE_MEM, i);
+		if (!res[i]) {
+			err = -EINVAL;
+			goto err1;
+		}
+	}
+	zcu->base.res = res;
+
+	zdev = zocl_get_zdev();
+	err = zocl_kds_add_cu(zdev, &zcu->base);
+	if (err) {
+		DRM_ERROR("Not able to add CU %p to KDS", zcu);
+		goto err1;
+	}
+
+	zcu->irq_name = kzalloc(20, GFP_KERNEL);
+	if (!zcu->irq_name)
+		return -ENOMEM;
+
+	sprintf(zcu->irq_name, "zocl_cu[%d]", info->intr_id);
+
+	if (info->intr_enable) {
+		zcu->irq = zdev->irq[info->intr_id];
+		/* Currently requesting irq if it's enable in cu config.
+		 * Not disabling it further, even user wants to use 
+		 * polling.
+		 */
+		err = request_irq(zcu->irq, cu_isr, 0,
+			  zcu->irq_name, zcu);
+		if (err) {
+			DRM_WARN("Failed to initial CU interrupt. "
+			    "Fall back to polling\n");
+			zcu->base.info.intr_enable = 0;
+		}
+	}
+
+	switch (info->model) {
+	case XCU_HLS:
+		err = xrt_cu_hls_init(&zcu->base);
+		break;
+	case XCU_FA:
+		err = xrt_cu_fa_init(&zcu->base);
+		break;
+	default:
+		err = -EINVAL;
+	}
+	if (err) {
+		DRM_ERROR("Not able to initial CU %p\n", zcu);
+		goto err2;
+	}
+
+	platform_set_drvdata(pdev, zcu);
+
+	err = sysfs_create_group(&pdev->dev.kobj, &cu_attrgroup);
+	if (err)
+		zocl_err(&pdev->dev, "create CU attrs failed: %d", err);
+
+	zcu->base.user_manage_irq = user_manage_irq;
+	zcu->base.configure_irq = configure_irq;
+
+	zocl_info(&pdev->dev, "CU[%d] created", info->cu_idx);
+	return 0;
+err2:
+	zocl_kds_del_cu(zdev, &zcu->base);
+err1:
+	vfree(args);
+	vfree(res);
+err:
+	kfree(zcu);
+	return err;
+}
+
+static int cu_remove(struct platform_device *pdev)
+{
+	struct zocl_cu *zcu;
+	struct drm_zocl_dev *zdev;
+	struct xrt_cu_info *info;
+
+	zcu = platform_get_drvdata(pdev);
+	if (!zcu)
+		return -EINVAL;
+
+	info = &zcu->base.info;
+	switch (info->model) {
+	case XCU_HLS:
+		xrt_cu_hls_fini(&zcu->base);
+		break;
+	case XCU_FA:
+		xrt_cu_fa_fini(&zcu->base);
+		break;
+	}
+
+	if (info->intr_enable)
+		free_irq(zcu->irq, zcu);
+
+	zdev = zocl_get_zdev();
+	if(zdev)
+		zocl_kds_del_cu(zdev, &zcu->base);
+
+	if (zcu->base.res)
+		vfree(zcu->base.res);
+
+	sysfs_remove_group(&pdev->dev.kobj, &cu_attrgroup);
+
+	zocl_info(&pdev->dev, "CU[%d] removed", info->cu_idx);
+	kfree(zcu->irq_name);
+	kfree(zcu);
+
+	return 0;
+}
+
+static struct platform_device_id cu_id_table[] = {
+	{"CU", 0 },
+	{ },
+};
+
+struct platform_driver cu_driver = {
+	.probe		= cu_probe,
+	.remove		= cu_remove,
+	.driver		= {
+		.name = "cu_drv",
+	},
+	.id_table	= cu_id_table,
+};
+u32 zocl_cu_get_status(struct platform_device *pdev)
+{
+	struct zocl_cu *zcu = platform_get_drvdata(pdev);
+
+	BUG_ON(!zcu);
+	return xrt_cu_get_status(&zcu->base);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/cu_scu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/cu_scu.c
@@ -0,0 +1,271 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Soft CU
+ *
+ * Copyright (C) 2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com, j.lin@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/delay.h>
+#include "xrt_cu.h"
+#include "xgq_cmd_ert.h"
+#include "zocl_drv.h"
+
+/* Control register bits and special behavior if any.
+ * Bit 0: ap_start(Read/Set). Clear by CU when ap_ready assert.
+ * Bit 1: ap_done(Read only). Clear on read.
+ * Bit 2: ap_idle(Read only).
+ * Bit 3: ap_ready(Read only). Self clear after clear ap_start.
+ * Bit 4: ap_continue(Read/Set). Self clear.
+ * Bit 5-7: Not support yet
+ */
+#define CTRL		0x0
+#define ARGS		0x4
+
+extern int kds_echo;
+
+struct xrt_cu_scu {
+	int			 max_credits;
+	int			 credits;
+	int			 run_cnts;
+	void			*vaddr;
+	struct semaphore	*sc_sem;
+	struct list_head	 submitted;
+	struct list_head	 completed;
+};
+
+static inline void cu_move_to_complete(struct xrt_cu_scu *cu, int status)
+{
+	struct kds_command *xcmd = NULL;
+
+	if (unlikely(list_empty(&cu->submitted)))
+		return;
+
+	xcmd = list_first_entry(&cu->submitted, struct kds_command, list);
+	xcmd->status = status;
+	list_move_tail(&xcmd->list, &cu->completed);
+}
+
+static int scu_alloc_credit(void *core)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+
+	return (scu->credits) ? scu->credits-- : 0;
+}
+
+static void scu_free_credit(void *core, u32 count)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+
+	scu->credits += count;
+	if (scu->credits > scu->max_credits)
+		scu->credits = scu->max_credits;
+}
+
+static int scu_peek_credit(void *core)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+
+	return scu->credits;
+}
+
+static void scu_xgq_start(struct xrt_cu_scu *scu, u32 *data)
+{
+	struct xgq_cmd_start_cuidx *cmd = (struct xgq_cmd_start_cuidx *)data;
+	u32 num_reg = 0;
+	u32 i = 0;
+	u32 *cu_regfile = scu->vaddr;
+
+	num_reg = (cmd->hdr.count - (sizeof(struct xgq_cmd_start_cuidx)
+				     - sizeof(cmd->hdr) - sizeof(cmd->data)))/sizeof(u32);
+	for (i = 0; i < num_reg; ++i) {
+		cu_regfile[i+1] = cmd->data[i];
+	}
+}
+
+static int scu_configure(void *core, u32 *data, size_t sz, int type)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+	struct xgq_cmd_sq_hdr *hdr = NULL;
+	size_t num_reg = 0;
+
+	if (kds_echo)
+		return 0;
+
+	num_reg = sz / sizeof(u32);
+	hdr = (struct xgq_cmd_sq_hdr *)data;
+	scu_xgq_start(scu, data);
+	return 0;
+}
+
+static void scu_start(void *core)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+	u32 *cu_regfile = scu->vaddr;
+
+	scu->run_cnts++;
+	if (kds_echo)
+		return;
+
+	*cu_regfile = CU_AP_START;
+	up(scu->sc_sem);
+}
+
+/*
+ * In ap_ctrl_hs protocol, HLS CU can run one task at a time. Once CU is
+ * started, software should wait for CU done before configure/start CU again.
+ * The done bit is clear on read. So, the software just need to read control
+ * register.
+ */
+static inline void
+scu_ctrl_hs_check(struct xrt_cu_scu *scu, struct xcu_status *status, bool force)
+{
+	u32 ctrl_reg = 0;
+	u32 done_reg = 0;
+	u32 ready_reg = 0;
+	u32 *cu_regfile = scu->vaddr;
+
+	/* Avoid access CU register unless we do have running commands.
+	 * This has a huge impact on performance.
+	 */
+	if (!force && !scu->run_cnts)
+		return;
+
+	ctrl_reg = *cu_regfile;
+	/* ap_ready and ap_done would assert at the same cycle */
+	if (ctrl_reg & CU_AP_DONE) {
+		done_reg  = 1;
+		ready_reg = 1;
+		scu->run_cnts--;
+		cu_move_to_complete(scu, KDS_COMPLETED);
+	}
+
+	status->num_done  = done_reg;
+	status->num_ready = ready_reg;
+	status->new_status = ctrl_reg;
+	status->rcode = cu_regfile[1];
+}
+
+static void scu_check(void *core, struct xcu_status *status, bool force)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+
+	if (kds_echo) {
+		scu->run_cnts--;
+		status->num_done = 1;
+		status->num_ready = 1;
+		status->new_status = CU_AP_IDLE;
+		return;
+	}
+
+	scu_ctrl_hs_check(scu, status, force);
+}
+
+static int scu_submit_config(void *core, struct kds_command *xcmd)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+	int ret = 0;
+
+	ret = scu_configure(core, (u32 *)xcmd->info, xcmd->isize, xcmd->payload_type);
+	if (ret)
+		return ret;
+
+	list_move_tail(&xcmd->list, &scu->submitted);
+	return ret;
+}
+
+static struct kds_command *scu_get_complete(void *core)
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+	struct kds_command *xcmd = NULL;
+
+	if (list_empty(&scu->completed))
+		return NULL;
+
+	xcmd = list_first_entry(&scu->completed, struct kds_command, list);
+	list_del_init(&xcmd->list);
+
+	return xcmd;
+}
+
+static int scu_abort(void *core, void *cond,
+			bool (*match)(struct kds_command *xcmd, void *cond))
+{
+	struct xrt_cu_scu *scu = (struct xrt_cu_scu *)core;
+	struct kds_command *xcmd = NULL;
+	struct kds_command *next = NULL;
+	int ret = -EBUSY;
+
+	list_for_each_entry_safe(xcmd, next, &scu->submitted, list) {
+		if (!match(xcmd, cond))
+			continue;
+
+		xcmd->status = KDS_TIMEOUT;
+		list_move_tail(&xcmd->list, &scu->completed);
+	}
+
+	return ret;
+}
+
+static struct xcu_funcs xrt_scu_funcs = {
+	.alloc_credit	= scu_alloc_credit,
+	.free_credit	= scu_free_credit,
+	.peek_credit	= scu_peek_credit,
+	.configure	= scu_configure,
+	.start		= scu_start,
+	.check		= scu_check,
+	.submit_config  = scu_submit_config,
+	.get_complete   = scu_get_complete,
+	.abort		= scu_abort,
+};
+
+int xrt_cu_scu_init(struct xrt_cu *xcu, void *vaddr, struct semaphore *sem)
+{
+	struct xrt_cu_scu *core = NULL;
+	int err = 0;
+
+	core = kzalloc(sizeof(struct xrt_cu_scu), GFP_KERNEL);
+	if (!core) {
+		err = -ENOMEM;
+		goto err;
+	}
+
+	core->max_credits = 1;
+	core->credits = core->max_credits;
+	core->run_cnts = 0;
+	core->sc_sem = sem;
+	core->vaddr = vaddr;
+	INIT_LIST_HEAD(&core->submitted);
+	INIT_LIST_HEAD(&core->completed);
+
+	xcu->core = core;
+	xcu->funcs = &xrt_scu_funcs;
+
+	xcu->busy_threshold = -1;
+	xcu->interval_min = 2;
+	xcu->interval_max = 5;
+
+	xcu->status = 0;
+	err = xrt_cu_init(xcu);
+	if (err)
+		return err;
+
+	return 0;
+
+err:
+	kfree(core);
+	return err;
+}
+
+void xrt_cu_scu_fini(struct xrt_cu *xcu)
+{
+	xrt_cu_fini(xcu);
+
+	if (xcu->core) {
+		kfree(xcu->core);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/ert.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/ert.h
@@ -0,0 +1,913 @@
+/*
+ *  Copyright (C) 2019-2022, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+/**
+ * DOC: XRT Embedded Runtime definition
+ *
+ * Header file *ert.h* defines data structures used by Emebdded Runtime (ERT) and
+ * XRT xclExecBuf() API.
+ */
+
+#ifndef _ERT_H_
+#define _ERT_H_
+
+#if defined(__KERNEL__)
+# include <linux/types.h>
+#elif defined(__cplusplus)
+# include <cstdint>
+#else
+# include <stdint.h>
+# include <stdbool.h>
+#endif
+
+#ifdef _WIN32
+# pragma warning( push )
+# pragma warning( disable : 4201 )
+#endif
+
+#define to_cfg_pkg(pkg) \
+    ((struct ert_configure_cmd *)(pkg))
+#define to_start_krnl_pkg(pkg) \
+    ((struct ert_start_kernel_cmd *)(pkg))
+#define to_copybo_pkg(pkg) \
+    ((struct ert_start_copybo_cmd *)(pkg))
+#define to_cfg_sk_pkg(pkg) \
+    ((struct ert_configure_sk_cmd *)(pkg))
+#define to_init_krnl_pkg(pkg) \
+    ((struct ert_init_kernel_cmd *)(pkg))
+#define to_validate_pkg(pkg) \
+    ((struct ert_validate_cmd *)(pkg))
+#define to_abort_pkg(pkg) \
+    ((struct ert_abort_cmd *)(pkg))
+
+
+#define HOST_RW_PATTERN     0xF0F0F0F0
+#define DEVICE_RW_PATTERN   0x0F0F0F0F
+
+/**
+ * struct ert_packet: ERT generic packet format
+ *
+ * @state:   [3-0] current state of a command
+ * @custom:  [11-4] custom per specific commands
+ * @count:   [22-12] number of words in payload (data)
+ * @opcode:  [27-23] opcode identifying specific command
+ * @type:    [31-28] type of command (currently 0)
+ * @data:    count number of words representing packet payload
+ */
+struct ert_packet {
+  union {
+    struct {
+      uint32_t state:4;   /* [3-0]   */
+      uint32_t custom:8;  /* [11-4]  */
+      uint32_t count:11;  /* [22-12] */
+      uint32_t opcode:5;  /* [27-23] */
+      uint32_t type:4;    /* [31-28] */
+    };
+    uint32_t header;
+  };
+  uint32_t data[1];   /* count number of words */
+};
+
+/**
+ * struct ert_start_kernel_cmd: ERT start kernel command format
+ *
+ * @state:           [3-0]   current state of a command
+ * @stat_enabled:    [4]     enabled driver to record timestamp for various
+ *                           states cmd has gone through. The stat data
+ *                           is appended after cmd data.
+ * @extra_cu_masks:  [11-10] extra CU masks in addition to mandatory mask
+ * @count:           [22-12] number of words following header for cmd data. Not
+ *                           include stat data.
+ * @opcode:          [27-23] 0, opcode for start_kernel
+ * @type:            [31-27] 0, type of start_kernel
+ *
+ * @cu_mask:         first mandatory CU mask
+ * @data:            count-1 number of words representing interpreted payload
+ *
+ * The packet payload is comprised of reserved id field, a mandatory CU mask,
+ * and extra_cu_masks per header field, followed by a CU register map of size
+ * (count - (1 + extra_cu_masks)) uint32_t words.
+ */
+struct ert_start_kernel_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t stat_enabled:1;   /* [4]     */
+      uint32_t unused:5;         /* [9-5]   */
+      uint32_t extra_cu_masks:2; /* [11-10] */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+
+  /* payload */
+  union {
+    uint32_t cu_mask;          /* mandatory cu mask */
+    int32_t return_code;       /* return code from soft kernel*/
+  };
+  uint32_t data[1];            /* count-1 number of words */
+};
+
+/**
+ * struct ert_init_kernel_cmd: ERT initialize kernel command format
+ * this command initializes CUs by writing CU registers. CUs are
+ * represented by cu_mask and extra_cu_masks.
+ *
+ * @state:           [3-0]   current state of a command
+ * @update_rtp:      [4]     command is for runtime update of cu argument
+ * @extra_cu_masks:  [11-10] extra CU masks in addition to mandatory mask
+ * @count:           [22-12] number of words following header
+ * @opcode:          [27-23] 0, opcode for init_kernel
+ * @type:            [31-27] 0, type of init_kernel
+ *
+ * @cu_run_timeout   the configured CU timeout value in Microseconds
+ *                   setting to 0 means CU should not timeout
+ * @cu_reset_timeout the configured CU reset timeout value in Microseconds
+ *                   when CU timeout, CU will be reset. this indicates
+ *                   CU reset should be completed within the timeout value.
+ *                   if cu_run_timeout is set to 0, this field is undefined.
+ *
+ * @cu_mask:         first mandatory CU mask
+ * @data:            count-9 number of words representing interpreted payload
+ *
+ * The packet payload is comprised of reserved id field, 8 reserved fields,
+ * a mandatory CU mask, and extra_cu_masks per header field, followed by a
+ * CU register map of size (count - (9 + extra_cu_masks)) uint32_t words.
+ */
+struct ert_init_kernel_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t update_rtp:1;     /* [4]  */
+      uint32_t unused:5;         /* [9-5]  */
+      uint32_t extra_cu_masks:2; /* [11-10]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+
+  uint32_t cu_run_timeout;   /* CU timeout value in Microseconds */
+  uint32_t cu_reset_timeout; /* CU reset timeout value in Microseconds */
+  uint32_t reserved[6];      /* reserved for future use */
+
+  /* payload */
+  uint32_t cu_mask;          /* mandatory cu mask */
+  uint32_t data[1];          /* count-9 number of words */
+};
+
+#define KDMA_BLOCK_SIZE 64   /* Limited by KDMA CU */
+struct ert_start_copybo_cmd {
+  uint32_t state:4;          /* [3-0], must be ERT_CMD_STATE_NEW */
+  uint32_t unused:6;         /* [9-4] */
+  uint32_t extra_cu_masks:2; /* [11-10], = 3 */
+  uint32_t count:11;         /* [22-12], = 16, exclude 'arg' */
+  uint32_t opcode:5;         /* [27-23], = ERT_START_COPYBO */
+  uint32_t type:4;           /* [31-27], = ERT_DEFAULT */
+  uint32_t cu_mask[4];       /* mandatory cu masks */
+  uint32_t reserved[4];      /* for scheduler use */
+  uint32_t src_addr_lo;      /* low 32 bit of src addr */
+  uint32_t src_addr_hi;      /* high 32 bit of src addr */
+  uint32_t src_bo_hdl;       /* src bo handle, cleared by driver */
+  uint32_t dst_addr_lo;      /* low 32 bit of dst addr */
+  uint32_t dst_addr_hi;      /* high 32 bit of dst addr */
+  uint32_t dst_bo_hdl;       /* dst bo handle, cleared by driver */
+  uint32_t size;             /* size in bytes low 32 bit*/
+  uint32_t size_hi;          /* size in bytes high 32 bit*/
+  void     *arg;             /* pointer to aux data for KDS */
+};
+
+/**
+ * struct ert_configure_cmd: ERT configure command format
+ *
+ * @state:           [3-0] current state of a command
+ * @count:           [22-12] number of words in payload (5 + num_cus)
+ * @opcode:          [27-23] 1, opcode for configure
+ * @type:            [31-27] 0, type of configure
+ *
+ * @slot_size:       command queue slot size
+ * @num_cus:         number of compute units in program
+ * @cu_shift:        shift value to convert CU idx to CU addr
+ * @cu_base_addr:    base address to add to CU addr for actual physical address
+ *
+ * @ert:1            enable embedded HW scheduler
+ * @polling:1        poll for command completion
+ * @cu_dma:1         enable CUDMA custom module for HW scheduler
+ * @cu_isr:1         enable CUISR custom module for HW scheduler
+ * @cq_int:1         enable interrupt from host to HW scheduler
+ * @cdma:1           enable CDMA kernel
+ * @unused:25
+ * @dsa52:1          reserved for internal use
+ *
+ * @data:            addresses of @num_cus CUs
+ */
+struct ert_configure_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t unused:8;         /* [11-4]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+
+  /* payload */
+  uint32_t slot_size;
+  uint32_t num_cus;
+  uint32_t cu_shift;
+  uint32_t cu_base_addr;
+
+  /* features */
+  uint32_t ert:1;
+  uint32_t polling:1;
+  uint32_t cu_dma:1;
+  uint32_t cu_isr:1;
+  uint32_t cq_int:1;
+  uint32_t cdma:1;
+  uint32_t dataflow:1;
+  /* WORKAROUND: allow xclRegWrite/xclRegRead access shared CU */
+  uint32_t rw_shared:1;
+  uint32_t kds_30:1;
+  uint32_t dmsg:1;
+  uint32_t echo:1;
+  uint32_t intr:1;
+  uint32_t unusedf:19;
+  uint32_t dsa52:1;
+
+  /* cu address map size is num_cus */
+  uint32_t data[1];
+};
+
+/*
+ * Note: We need to put maximum 128 soft kernel image
+ *       in one config command (1024 DWs including header).
+ *       So each one needs to be smaller than 8 DWs.
+ *
+ * This data struct is obsoleted. Only used in legacy ERT firmware.
+ * Use 'struct config_sk_image_uuid' instead on XGQ based ERT.
+ *
+ * @start_cuidx:     start index of compute units of each image
+ * @num_cus:         number of compute units of each image
+ * @sk_name:         symbol name of soft kernel of each image
+ */
+struct config_sk_image {
+  uint32_t start_cuidx;
+  uint32_t num_cus;
+  uint32_t sk_name[5];
+};
+
+/*
+ * Note: We need to put maximum 128 soft kernel image
+ *       in one config command (1024 DWs including header).
+ *       So each one needs to be smaller than 8 DWs.
+ *
+ * @start_cuidx:     start index of compute units of each image
+ * @num_cus:         number of compute units of each image
+ * @sk_name:         symbol name of soft kernel of each image
+ * @sk_uuid:         xclbin uuid that this soft kernel image belones to
+ */
+struct config_sk_image_uuid {
+  uint32_t start_cuidx;
+  uint32_t num_cus;
+  uint32_t sk_name[5];
+  unsigned char     sk_uuid[16];
+};
+
+/**
+ * struct ert_configure_sk_cmd: ERT configure soft kernel command format
+ *
+ * @state:           [3-0] current state of a command
+ * @count:           [22-12] number of words in payload
+ * @opcode:          [27-23] 1, opcode for configure
+ * @type:            [31-27] 0, type of configure
+ *
+ * @num_image:       number of images
+*/
+struct ert_configure_sk_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t unused:8;         /* [11-4]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+
+  /* payload */
+  uint32_t num_image;
+  struct config_sk_image image[1];
+};
+
+/**
+ * struct ert_unconfigure_sk_cmd: ERT unconfigure soft kernel command format
+ *
+ * @state:           [3-0] current state of a command
+ * @count:           [22-12] number of words in payload
+ * @opcode:          [27-23] 1, opcode for configure
+ * @type:            [31-27] 0, type of configure
+ *
+ * @start_cuidx:     start index of compute units
+ * @num_cus:         number of compute units in program
+ */
+struct ert_unconfigure_sk_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t unused:8;         /* [11-4]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+
+  /* payload */
+  uint32_t start_cuidx;
+  uint32_t num_cus;
+};
+
+/**
+ * struct ert_abort_cmd: ERT abort command format.
+ *
+ * @exec_bo_handle: The bo handle of execbuf command to abort
+ */
+struct ert_abort_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t custom:8;         /* [11-4]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+
+  /* payload */
+  uint64_t exec_bo_handle;
+};
+
+/**
+ * struct ert_validate_cmd: ERT BIST command format.
+ *
+ */
+struct ert_validate_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t custom:8;         /* [11-4]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+  uint32_t timestamp;
+  uint32_t cq_read_single;
+  uint32_t cq_write_single;
+  uint32_t cu_read_single;
+  uint32_t cu_write_single;
+};
+
+/**
+ * struct ert_validate_cmd: ERT BIST command format.
+ *
+ */
+struct ert_access_valid_cmd {
+  union {
+    struct {
+      uint32_t state:4;          /* [3-0]   */
+      uint32_t custom:8;         /* [11-4]  */
+      uint32_t count:11;         /* [22-12] */
+      uint32_t opcode:5;         /* [27-23] */
+      uint32_t type:4;           /* [31-27] */
+    };
+    uint32_t header;
+  };
+  uint32_t h2h_access;
+  uint32_t h2d_access;
+  uint32_t d2h_access;
+  uint32_t d2d_access;
+  uint32_t d2cu_access;
+  uint32_t wr_count;
+  uint32_t wr_test;
+};
+
+/**
+ * ERT command state
+ *
+ * @ERT_CMD_STATE_NEW:         Set by host before submitting a command to
+ *                             scheduler
+ * @ERT_CMD_STATE_QUEUED:      Internal scheduler state
+ * @ERT_CMD_STATE_SUBMITTED:   Internal scheduler state
+ * @ERT_CMD_STATE_RUNNING:     Internal scheduler state
+ * @ERT_CMD_STATE_COMPLETE:    Set by scheduler when command completes
+ * @ERT_CMD_STATE_ERROR:       Set by scheduler if command failed
+ * @ERT_CMD_STATE_ABORT:       Set by scheduler if command abort
+ * @ERT_CMD_STATE_TIMEOUT:     Set by scheduler if command timeout and reset
+ * @ERT_CMD_STATE_NORESPONSE:  Set by scheduler if command timeout and fail to
+ *                             reset
+ */
+enum ert_cmd_state {
+  ERT_CMD_STATE_NEW = 1,
+  ERT_CMD_STATE_QUEUED = 2,
+  ERT_CMD_STATE_RUNNING = 3,
+  ERT_CMD_STATE_COMPLETED = 4,
+  ERT_CMD_STATE_ERROR = 5,
+  ERT_CMD_STATE_ABORT = 6,
+  ERT_CMD_STATE_SUBMITTED = 7,
+  ERT_CMD_STATE_TIMEOUT = 8,
+  ERT_CMD_STATE_NORESPONSE = 9,
+  ERT_CMD_STATE_SKERROR = 10, //Check for error return code from Soft Kernel
+  ERT_CMD_STATE_SKCRASHED = 11, //Soft kernel has crashed
+  ERT_CMD_STATE_MAX, // Always the last one
+};
+
+struct cu_cmd_state_timestamps {
+  uint64_t skc_timestamps[ERT_CMD_STATE_MAX]; // In nano-second
+};
+
+/**
+ * Opcode types for commands
+ *
+ * @ERT_START_CU:       start a workgroup on a CU
+ * @ERT_START_KERNEL:   currently aliased to ERT_START_CU
+ * @ERT_CONFIGURE:      configure command scheduler
+ * @ERT_EXEC_WRITE:     execute a specified CU after writing
+ * @ERT_CU_STAT:        get stats about CU execution
+ * @ERT_START_COPYBO:   start KDMA CU or P2P, may be converted to ERT_START_CU
+ *                      before cmd reach to scheduler, short-term hack
+ * @ERT_SK_CONFIG:      configure soft kernel
+ * @ERT_SK_START:       start a soft kernel
+ * @ERT_SK_UNCONFIG:    unconfigure a soft kernel
+ * @ERT_START_KEY_VAL:  same as ERT_START_CU but with key-value pair flavor
+ */
+enum ert_cmd_opcode {
+  ERT_START_CU      = 0,
+  ERT_START_KERNEL  = 0,
+  ERT_CONFIGURE     = 2,
+  ERT_EXIT          = 3,
+  ERT_ABORT         = 4,
+  ERT_EXEC_WRITE    = 5,
+  ERT_CU_STAT       = 6,
+  ERT_START_COPYBO  = 7,
+  ERT_SK_CONFIG     = 8,
+  ERT_SK_START      = 9,
+  ERT_SK_UNCONFIG   = 10,
+  ERT_INIT_CU       = 11,
+  ERT_START_FA      = 12,
+  ERT_CLK_CALIB     = 13,
+  ERT_MB_VALIDATE   = 14,
+  ERT_START_KEY_VAL = 15,
+  ERT_ACCESS_TEST_C = 16,
+  ERT_ACCESS_TEST   = 17,
+};
+
+/**
+ * Command types
+ *
+ * @ERT_DEFAULT:        default command type
+ * @ERT_KDS_LOCAL:      command processed by KDS locally
+ * @ERT_CTRL:           control command uses reserved command queue slot
+ * @ERT_CU:             compute unit command
+ */
+enum ert_cmd_type {
+  ERT_DEFAULT = 0,
+  ERT_KDS_LOCAL = 1,
+  ERT_CTRL = 2,
+  ERT_CU = 3,
+  ERT_SCU = 4,
+};
+
+/**
+ * Soft kernel types
+ *
+ * @SOFTKERNEL_TYPE_EXEC:       executable
+ */
+enum softkernel_type {
+  SOFTKERNEL_TYPE_EXEC = 0,
+};
+
+/*
+ * Base address GPIO per spec
+ * | Offset  | Description
+ * -----------------------
+ * | 0x00    | ERT_MGMT_PF_base_addr (Not sure where this should be use)
+ * | 0x08    | ERT_USER_PF_base_addr. The base address of ERT peripherals
+ */
+#if defined(ERT_BUILD_V20)
+uint32_t ert_base_addr = 0;
+# define ERT_BASE_ADDR                     0x01F30008
+#endif
+
+#if defined(ERT_BUILD_V30)
+uint32_t ert_base_addr = 0;
+# define ERT_BASE_ADDR                     0x01F30008
+#endif
+
+/**
+ * Address constants per spec
+ */
+#define ERT_WORD_SIZE                      4          /* 4 bytes */
+#define ERT_CQ_SIZE                        0x10000    /* 64K */
+#if defined(ERT_BUILD_U50)
+# define ERT_CQ_BASE_ADDR                  0x340000
+# define ERT_CSR_ADDR                      0x360000
+#elif defined(ERT_BUILD_V20)
+# define ERT_CQ_BASE_ADDR                  (0x000000 + ert_base_addr)
+# define ERT_CSR_ADDR                      (0x010000 + ert_base_addr)
+#elif defined(ERT_BUILD_V30)
+# define ERT_CQ_BASE_ADDR                  0x1F60000
+# define ERT_CSR_ADDR                      (0x010000 + ert_base_addr)
+#else
+# define ERT_CQ_BASE_ADDR                  0x190000
+# define ERT_CSR_ADDR                      0x180000
+#endif
+
+/**
+ * The STATUS REGISTER is for communicating completed CQ slot indices
+ * MicroBlaze write, host reads.  MB(W) / HOST(COR)
+ */
+#define ERT_STATUS_REGISTER_ADDR          (ERT_CSR_ADDR)
+#define ERT_STATUS_REGISTER_ADDR0         (ERT_CSR_ADDR)
+#define ERT_STATUS_REGISTER_ADDR1         (ERT_CSR_ADDR + 0x4)
+#define ERT_STATUS_REGISTER_ADDR2         (ERT_CSR_ADDR + 0x8)
+#define ERT_STATUS_REGISTER_ADDR3         (ERT_CSR_ADDR + 0xC)
+
+/**
+ * The CU DMA REGISTER is for communicating which CQ slot is to be started
+ * on a specific CU.  MB selects a free CU on which the command can
+ * run, then writes the 1<<CU back to the command slot CU mask and
+ * writes the slot index to the CU DMA REGISTER.  HW is notified when
+ * the register is written and now does the DMA transfer of CU regmap
+ * map from command to CU, while MB continues its work. MB(W) / HW(R)
+ */
+#define ERT_CU_DMA_ENABLE_ADDR            (ERT_CSR_ADDR + 0x18)
+#define ERT_CU_DMA_REGISTER_ADDR          (ERT_CSR_ADDR + 0x1C)
+#define ERT_CU_DMA_REGISTER_ADDR0         (ERT_CSR_ADDR + 0x1C)
+#define ERT_CU_DMA_REGISTER_ADDR1         (ERT_CSR_ADDR + 0x20)
+#define ERT_CU_DMA_REGISTER_ADDR2         (ERT_CSR_ADDR + 0x24)
+#define ERT_CU_DMA_REGISTER_ADDR3         (ERT_CSR_ADDR + 0x28)
+
+/**
+ * The SLOT SIZE is the size of slots in command queue, it is
+ * configurable per xclbin. MB(W) / HW(R)
+ */
+#define ERT_CQ_SLOT_SIZE_ADDR             (ERT_CSR_ADDR + 0x2C)
+
+/**
+ * The CU_OFFSET is the size of a CU's address map in power of 2.  For
+ * example a 64K regmap is 2^16 so 16 is written to the CU_OFFSET_ADDR.
+ * MB(W) / HW(R)
+ */
+#define ERT_CU_OFFSET_ADDR                (ERT_CSR_ADDR + 0x30)
+
+/**
+ * The number of slots is command_queue_size / slot_size.
+ * MB(W) / HW(R)
+ */
+#define ERT_CQ_NUMBER_OF_SLOTS_ADDR       (ERT_CSR_ADDR + 0x34)
+
+/**
+ * All CUs placed in same address space separated by CU_OFFSET. The
+ * CU_BASE_ADDRESS is the address of the first CU. MB(W) / HW(R)
+ */
+#define ERT_CU_BASE_ADDRESS_ADDR          (ERT_CSR_ADDR + 0x38)
+
+/**
+ * The CQ_BASE_ADDRESS is the base address of the command queue.
+ * MB(W) / HW(R)
+ */
+#define ERT_CQ_BASE_ADDRESS_ADDR          (ERT_CSR_ADDR + 0x3C)
+
+/**
+ * The CU_ISR_HANDLER_ENABLE (MB(W)/HW(R)) enables the HW handling of
+ * CU interrupts.  When a CU interrupts (when done), hardware handles
+ * the interrupt and writes the index of the CU that completed into
+ * the CU_STATUS_REGISTER (HW(W)/MB(COR)) as a bitmask
+ */
+#define ERT_CU_ISR_HANDLER_ENABLE_ADDR    (ERT_CSR_ADDR + 0x40)
+#define ERT_CU_STATUS_REGISTER_ADDR       (ERT_CSR_ADDR + 0x44)
+#define ERT_CU_STATUS_REGISTER_ADDR0      (ERT_CSR_ADDR + 0x44)
+#define ERT_CU_STATUS_REGISTER_ADDR1      (ERT_CSR_ADDR + 0x48)
+#define ERT_CU_STATUS_REGISTER_ADDR2      (ERT_CSR_ADDR + 0x4C)
+#define ERT_CU_STATUS_REGISTER_ADDR3      (ERT_CSR_ADDR + 0x50)
+
+/**
+ * The CQ_STATUS_ENABLE (MB(W)/HW(R)) enables interrupts from HOST to
+ * MB to indicate the presense of a new command in some slot.  The
+ * slot index is written to the CQ_STATUS_REGISTER (HOST(W)/MB(R))
+ */
+#define ERT_CQ_STATUS_ENABLE_ADDR         (ERT_CSR_ADDR + 0x54)
+#define ERT_CQ_STATUS_REGISTER_ADDR       (ERT_CSR_ADDR + 0x58)
+#define ERT_CQ_STATUS_REGISTER_ADDR0      (ERT_CSR_ADDR + 0x58)
+#define ERT_CQ_STATUS_REGISTER_ADDR1      (ERT_CSR_ADDR + 0x5C)
+#define ERT_CQ_STATUS_REGISTER_ADDR2      (ERT_CSR_ADDR + 0x60)
+#define ERT_CQ_STATUS_REGISTER_ADDR3      (ERT_CSR_ADDR + 0x64)
+
+/**
+ * The NUMBER_OF_CU (MB(W)/HW(R) is the number of CUs per current
+ * xclbin.  This is an optimization that allows HW to only check CU
+ * completion on actual CUs.
+ */
+#define ERT_NUMBER_OF_CU_ADDR             (ERT_CSR_ADDR + 0x68)
+
+/**
+ * Enable global interrupts from MB to HOST on command completion.
+ * When enabled writing to STATUS_REGISTER causes an interrupt in HOST.
+ * MB(W)
+ */
+#define ERT_HOST_INTERRUPT_ENABLE_ADDR    (ERT_CSR_ADDR + 0x100)
+
+/**
+ * Interrupt controller base address
+ * This value is per hardware BSP (XPAR_INTC_SINGLE_BASEADDR)
+ */
+#if defined(ERT_BUILD_U50)
+# define ERT_INTC_ADDR                     0x00310000
+#elif defined(ERT_BUILD_V20)
+# define ERT_INTC_ADDR                     0x01F20000
+#elif defined(ERT_BUILD_V30)
+# define ERT_INTC_ADDR                     0x01F20000
+# define ERT_INTC_CU_0_31_ADDR             (0x0000 + ert_base_addr)
+# define ERT_INTC_CU_32_63_ADDR            (0x1000 + ert_base_addr)
+# define ERT_INTC_CU_64_95_ADDR            (0x2000 + ert_base_addr)
+# define ERT_INTC_CU_96_127_ADDR           (0x3000 + ert_base_addr)
+#else
+# define ERT_INTC_ADDR                     0x41200000
+# define ERT_INTC_CU_0_31_ADDR             0x0000
+# define ERT_INTC_CU_32_63_ADDR            0x1000
+# define ERT_INTC_CU_64_95_ADDR            0x2000
+# define ERT_INTC_CU_96_127_ADDR           0x3000
+#endif
+
+/**
+ * Look up table for CUISR for CU addresses
+ */
+#define ERT_CUISR_LUT_ADDR                (ERT_CSR_ADDR + 0x400)
+
+/**
+ * ERT exit command/ack
+ */
+#define	ERT_EXIT_CMD			  ((ERT_EXIT << 23) | ERT_CMD_STATE_NEW)
+#define	ERT_EXIT_ACK			  (ERT_CMD_STATE_COMPLETED)
+#define	ERT_EXIT_CMD_OP			  (ERT_EXIT << 23)
+
+/**
+ * State machine for both CUDMA and CUISR modules
+ */
+#define ERT_HLS_MODULE_IDLE               0x1
+#define ERT_CUDMA_STATE                   (ERT_CSR_ADDR + 0x318)
+#define ERT_CUISR_STATE                   (ERT_CSR_ADDR + 0x328)
+
+/**
+ * Interrupt address masks written by MB when interrupts from
+ * CU are enabled
+ */
+#define ERT_INTC_IPR_ADDR                 (ERT_INTC_ADDR + 0x4)  /* pending */
+#define ERT_INTC_IER_ADDR                 (ERT_INTC_ADDR + 0x8)  /* enable */
+#define ERT_INTC_IAR_ADDR                 (ERT_INTC_ADDR + 0x0C) /* acknowledge */
+#define ERT_INTC_MER_ADDR                 (ERT_INTC_ADDR + 0x1C) /* master enable */
+
+#define ERT_INTC_CU_0_31_IPR              (ERT_INTC_CU_0_31_ADDR + 0x4)  /* pending */
+#define ERT_INTC_CU_0_31_IER              (ERT_INTC_CU_0_31_ADDR + 0x8)  /* enable */
+#define ERT_INTC_CU_0_31_IAR              (ERT_INTC_CU_0_31_ADDR + 0x0C) /* acknowledge */
+#define ERT_INTC_CU_0_31_MER              (ERT_INTC_CU_0_31_ADDR + 0x1C) /* master enable */
+
+#define ERT_INTC_CU_32_63_IPR             (ERT_INTC_CU_32_63_ADDR + 0x4)  /* pending */
+#define ERT_INTC_CU_32_63_IER             (ERT_INTC_CU_32_63_ADDR + 0x8)  /* enable */
+#define ERT_INTC_CU_32_63_IAR             (ERT_INTC_CU_32_63_ADDR + 0x0C) /* acknowledge */
+#define ERT_INTC_CU_32_63_MER             (ERT_INTC_CU_32_63_ADDR + 0x1C) /* master enable */
+
+#define ERT_INTC_CU_64_95_IPR             (ERT_INTC_CU_64_95_ADDR + 0x4)  /* pending */
+#define ERT_INTC_CU_64_95_IER             (ERT_INTC_CU_64_95_ADDR + 0x8)  /* enable */
+#define ERT_INTC_CU_64_95_IAR             (ERT_INTC_CU_64_95_ADDR + 0x0C) /* acknowledge */
+#define ERT_INTC_CU_64_95_MER             (ERT_INTC_CU_64_95_ADDR + 0x1C) /* master enable */
+
+#define ERT_INTC_CU_96_127_IPR            (ERT_INTC_CU_96_127_ADDR + 0x4)  /* pending */
+#define ERT_INTC_CU_96_127_IER            (ERT_INTC_CU_96_127_ADDR + 0x8)  /* enable */
+#define ERT_INTC_CU_96_127_IAR            (ERT_INTC_CU_96_127_ADDR + 0x0C) /* acknowledge */
+#define ERT_INTC_CU_96_127_MER            (ERT_INTC_CU_96_127_ADDR + 0x1C) /* master enable */
+
+
+#if defined(ERT_BUILD_V30)
+# define ERT_CLK_COUNTER_ADDR              0x1F70000
+#else
+# define ERT_CLK_COUNTER_ADDR              0x0
+#endif
+
+/*
+* Used in driver and user space code
+*/
+/*
+* Upper limit on number of dependencies in execBuf waitlist
+*/
+#define MAX_DEPS        8
+
+/*
+* Maximum size of mandatory fields in bytes for all packet type
+*/
+#define MAX_HEADER_SIZE 64
+
+/*
+* Maximum size of mandatory fields in bytes for all packet type
+*/
+#define MAX_CONFIG_PACKET_SIZE 512
+
+/*
+* Maximum size of CQ slot
+*/
+#define MAX_CQ_SLOT_SIZE 4096
+
+/*
+ * Helper functions to hide details of ert_start_copybo_cmd
+ */
+static inline void
+ert_fill_copybo_cmd(struct ert_start_copybo_cmd *pkt, uint32_t src_bo,
+  uint32_t dst_bo, uint64_t src_offset, uint64_t dst_offset, uint32_t size)
+{
+  pkt->state = ERT_CMD_STATE_NEW;
+  pkt->extra_cu_masks = 3;
+  pkt->count = 16;
+  pkt->opcode = ERT_START_COPYBO;
+  pkt->type = ERT_DEFAULT;
+  pkt->cu_mask[0] = 0;
+  pkt->cu_mask[1] = 0;
+  pkt->cu_mask[2] = 0;
+  pkt->cu_mask[3] = 0;
+  pkt->src_addr_lo = (uint32_t)src_offset;
+  pkt->src_addr_hi = (src_offset >> 32) & 0xFFFFFFFF;
+  pkt->src_bo_hdl = src_bo;
+  pkt->dst_addr_lo = (uint32_t)dst_offset;
+  pkt->dst_addr_hi = (dst_offset >> 32) & 0xFFFFFFFF;
+  pkt->dst_bo_hdl = dst_bo;
+  pkt->size = size;
+  pkt->size_hi = 0; /* set to 0 explicitly */
+  pkt->arg = 0;
+}
+static inline uint64_t
+ert_copybo_src_offset(struct ert_start_copybo_cmd *pkt)
+{
+  return (uint64_t)pkt->src_addr_hi << 32 | pkt->src_addr_lo;
+}
+static inline uint64_t
+ert_copybo_dst_offset(struct ert_start_copybo_cmd *pkt)
+{
+  return (uint64_t)pkt->dst_addr_hi << 32 | pkt->dst_addr_lo;
+}
+static inline uint64_t
+ert_copybo_size(struct ert_start_copybo_cmd *pkt)
+{
+  return pkt->size;
+}
+
+static inline bool
+ert_valid_opcode(struct ert_packet *pkt)
+{
+  struct ert_start_kernel_cmd *skcmd;
+  struct ert_init_kernel_cmd *ikcmd;
+  struct ert_start_copybo_cmd *sccmd;
+  struct ert_configure_cmd *ccmd;
+  struct ert_configure_sk_cmd *cscmd;
+  bool valid;
+
+  switch (pkt->opcode) {
+  case ERT_START_CU:
+    skcmd = to_start_krnl_pkg(pkt);
+    /* 1 cu mask + 4 registers */
+    valid = (skcmd->count >= skcmd->extra_cu_masks + 1 + 4);
+    break;
+  case ERT_START_KEY_VAL:
+    skcmd = to_start_krnl_pkg(pkt);
+    /* 1 cu mask */
+    valid = (skcmd->count >= skcmd->extra_cu_masks + 1);
+    break;
+  case ERT_EXEC_WRITE:
+    skcmd = to_start_krnl_pkg(pkt);
+    /* 1 cu mask + 6 registers */
+    valid = (skcmd->count >= skcmd->extra_cu_masks + 1 + 6);
+    break;
+  case ERT_START_FA:
+    skcmd = to_start_krnl_pkg(pkt);
+    /* 1 cu mask */
+    valid = (skcmd->count >= skcmd->extra_cu_masks + 1);
+    break;
+  case ERT_SK_START:
+    skcmd = to_start_krnl_pkg(pkt);
+    /* 1 cu mask + 1 control word */
+    valid = (skcmd->count >= skcmd->extra_cu_masks + 1 + 1);
+    break;
+  case ERT_CONFIGURE:
+    ccmd = to_cfg_pkg(pkt);
+    /* 5 mandatory fields in struct */
+    valid = (ccmd->count >= 5 + ccmd->num_cus);
+    break;
+  case ERT_START_COPYBO:
+    sccmd = to_copybo_pkg(pkt);
+    valid = (sccmd->count == 16);
+    break;
+  case ERT_INIT_CU:
+    ikcmd = to_init_krnl_pkg(pkt);
+    /* 9 mandatory words in struct + 4 control registers */
+    valid = (ikcmd->count >= ikcmd->extra_cu_masks + 9 + 4);
+    break;
+  case ERT_SK_CONFIG:
+    cscmd = to_cfg_sk_pkg(pkt);
+    valid = (cscmd->count == sizeof(struct config_sk_image) * cscmd->num_image / 4 + 1);
+    break;
+  case ERT_CLK_CALIB:
+  case ERT_MB_VALIDATE:
+  case ERT_ACCESS_TEST_C:  
+  case ERT_CU_STAT: /* TODO: Rules to validate? */
+  case ERT_EXIT:
+  case ERT_ABORT:
+    valid = true;
+    break;
+  case ERT_SK_UNCONFIG: /* NOTE: obsolete */
+  default:
+    valid = false;
+  }
+
+  return valid;
+}
+
+#ifdef __GNUC__
+#define P2ROUNDUP(x, align)     (-(-(x) & -(align)))
+static inline struct cu_cmd_state_timestamps *
+ert_start_kernel_timestamps(struct ert_start_kernel_cmd *pkt)
+{
+  uint64_t offset = pkt->count * sizeof(uint32_t) + sizeof(pkt->header);
+  /* Make sure the offset of timestamps are properly aligned. */
+  return (struct cu_cmd_state_timestamps *)
+    ((char *)pkt + P2ROUNDUP(offset, sizeof(uint64_t)));
+}
+
+/* Return 0 if this pkt doesn't support timestamp or disabled */
+static inline int
+get_size_with_timestamps_or_zero(struct ert_packet *pkt)
+{
+  struct ert_start_kernel_cmd *skcmd;
+  int size = 0;
+
+  switch (pkt->opcode) {
+  case ERT_START_CU:
+  case ERT_EXEC_WRITE:
+  case ERT_START_FA:
+  case ERT_SK_START:
+    skcmd = to_start_krnl_pkg(pkt);
+    if (skcmd->stat_enabled) {
+      size = (char *)ert_start_kernel_timestamps(skcmd) - (char *)pkt;
+      size += sizeof(struct cu_cmd_state_timestamps);
+    }
+  }
+
+  return size;
+}
+#endif
+
+#ifdef _WIN32
+# pragma warning( pop )
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/kds_client.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/kds_client.h
@@ -0,0 +1,102 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2021-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_CLIENT_H
+#define _KDS_CLIENT_H
+
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/pid.h>
+#include <linux/device.h>
+#include <linux/uuid.h>
+
+#include "xrt_cu.h"
+#include "kds_stat.h"
+
+#define EV_ABORT	0x1
+
+/* Multiple xclbin context can be active under a single client.
+ * Client should maintain all the active XCLBIN.
+ */
+struct kds_client_ctx {
+	struct list_head          link;
+	void			 *xclbin_id;
+	u32			  slot_idx;
+	u32			  num_ctx;
+	u32			  num_scu_ctx;
+	u32			  virt_cu_ref;
+};
+
+/**
+ * struct kds_client: Manage user client
+ * Whenever user applciation open the device, a client would be created.
+ * A client will keep alive util application close the device or being killed.
+ * The client could open multiple contexts to access compute resources.
+ *
+ * @link: Client is added to list in KDS scheduler
+ * @dev:  Device
+ * @pid:  Client process ID
+ * @lock: Mutex to protext context related members
+ * @xclbin_id: UUID of xclbin cache
+ * @num_ctx: Number of context that opened
+ * @num_scu_ctx: Number of soft kernel context that opened
+ * @virt_cu_ref: Reference count of virtual CU
+ * @cu_bitmap: bitmap of opening CU
+ * @scu_bitmap: bitmap of opening SCU
+ * @waitq: Wait queue for poll client
+ * @event: Events to notify user client
+ */
+struct kds_client {
+	struct list_head	  link;
+	struct device	         *dev;
+	struct pid	         *pid;
+	struct mutex		  lock;
+
+	/* TODO: xocl not suppot multiple xclbin context yet. */
+	struct kds_client_ctx    *ctx;
+	struct list_head          ctx_list;
+
+	struct list_head          graph_list;
+	spinlock_t                graph_list_lock;
+	u32                       aie_ctx;
+
+	DECLARE_BITMAP(cu_bitmap, MAX_CUS);
+	DECLARE_BITMAP(scu_bitmap, MAX_CUS);
+	/* Per client statistics. Use percpu variable for two reasons
+	 * 1. no lock is need while modifying these counters
+	 * 2. do not need to worry about cache false share
+	 */
+	struct client_stats __percpu *stats;
+
+	struct list_head	  ev_entry;
+	int			  ev_type;
+
+	/*
+	 * Below are modified when the other thread is completing commands.
+	 * In order to prevent false sharing, they need to be in different
+	 * cache lines.
+	 */
+	wait_queue_head_t	  waitq ____cacheline_aligned_in_smp;
+	atomic_t		  event;
+};
+
+/* Macros to operates client statistics */
+#define client_stat_read(client, field) \
+	stat_read((client)->stats, field)
+
+#define client_stat_inc(client, field) \
+	this_stat_inc((client)->stats, field)
+
+#define client_stat_dec(client, field) \
+	this_stat_dec((client)->stats, field)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/kds_command.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/kds_command.h
@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2020-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_COMMAND_H
+#define _KDS_COMMAND_H
+
+#include "xgq_cmd_ert.h"
+/* Userspace command format */
+#include "ert.h"
+
+#define REGMAP 0
+#define KEY_VAL 1
+#define XGQ_CMD 2
+
+enum kds_opcode {
+	OP_NONE = 0,
+	OP_CONFIG,
+	OP_START,
+	OP_ABORT,
+	OP_CONFIG_SK, /* TODO: There is a plan to remove softkernel config and unconfig command */
+	OP_START_SK,
+	OP_CLK_CALIB,
+	OP_VALIDATE,
+	OP_GET_STAT,
+};
+
+/* KDS_NEW:		Command is validated
+ * KDS_QUEUED:		Command is sent to pending queue
+ * KDS_RUNNING:		Command is sent to hardware (CU/ERT)
+ * KDS_COMPLETED:	Command is completed
+ * KDS_ERROR:		Command is error out
+ * KDS_ABORT:		Command is abort
+ * KDS_TIMEOUT:		Command is timeout
+ */
+enum kds_status {
+	KDS_NEW = 0,
+	KDS_QUEUED,
+	KDS_RUNNING,
+	KDS_COMPLETED,
+	KDS_ERROR,
+	KDS_ABORT,
+	KDS_TIMEOUT,
+	KDS_STAT_MAX,
+};
+
+struct kds_command;
+
+struct kds_cmd_ops {
+	void (*notify_host)(struct kds_command *xcmd, int status);
+	void (*free)(struct kds_command *xcmd);
+};
+
+struct in_kernel_cb {
+	void (*func)(unsigned long cb_data, int err);
+	void *data;
+};
+
+/* Default cu index of a command */
+#define NO_INDEX -1
+
+/**
+ * struct kds_command: KDS command struct
+ * @client: the client that the command belongs to
+ * @type:   type of the command. Use this to determin controller
+ */
+struct kds_command {
+	struct kds_client	*client;
+	int			 status;
+	u32			 rcode;
+	int			 cu_idx;
+	u32			 type;
+	u32			 opcode;
+	struct list_head	 list;
+	u32			 payload_alloc;
+	u32			 payload_type;
+	void			*info;
+	size_t			 isize;
+	void                    *response;
+	size_t                   response_size;
+	struct kds_cmd_ops	 cb;
+	void			*priv;
+
+	unsigned int		 tick;
+	u32			 timestamp_enabled;
+	u64			 timestamp[KDS_STAT_MAX];
+
+	/* TODO: may rethink if we should have cu bit mask here
+	 * or move it to info.
+	 * Since NO all types of command have cu_mask
+	 */
+	u32			 cu_mask[4];
+	u32			 num_mask;
+	u64			 start;
+
+	/* execbuf is used to update the header
+	 * of execbuf when notifying host
+	 */
+	u32			*execbuf;
+	u32			*u_execbuf;
+	void			*gem_obj;
+	u32			 exec_bo_handle;
+	/* to notify inkernel exec completion */
+	struct in_kernel_cb	*inkern_cb;
+};
+
+void set_xcmd_timestamp(struct kds_command *xcmd, enum kds_status s);
+
+/* execbuf command related funtions */
+void cfg_ecmd2xcmd(struct ert_configure_cmd *ecmd,
+		   struct kds_command *xcmd);
+void start_krnl_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd);
+void start_skrnl_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			  struct kds_command *xcmd);
+void start_krnl_kv_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			     struct kds_command *xcmd);
+void start_fa_ecmd2xcmd(struct ert_start_kernel_cmd *ecmd,
+			struct kds_command *xcmd);
+void abort_ecmd2xcmd(struct ert_abort_cmd *ecmd,
+		     struct kds_command *xcmd);
+int cu_mask_to_cu_idx(struct kds_command *xcmd, uint8_t *cus);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/kds_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/kds_core.h
@@ -0,0 +1,211 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_CORE_H
+#define _KDS_CORE_H
+
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/pid.h>
+#include <linux/device.h>
+#include <linux/uuid.h>
+#include <linux/kthread.h>
+
+#include "kds_client.h"
+#include "kds_command.h"
+#include "xrt_cu.h"
+#include "kds_stat.h"
+#include "xclbin.h"
+
+#define kds_info(client, fmt, args...)			\
+	dev_info(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+#define kds_err(client, fmt, args...)			\
+	dev_err(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+#define kds_warn(client, fmt, args...)			\
+	dev_warn(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+#define kds_dbg(client, fmt, args...)			\
+	dev_dbg(client->dev, " %llx %s: "fmt, (u64)client->dev, __func__, ##args)
+
+enum kds_type {
+	KDS_CU		= 0,
+	KDS_SCU,
+	KDS_ERT,
+	KDS_MAX_TYPE, // always the last one
+};
+
+/* Context properties */
+#define	CU_CTX_PROP_MASK	0x0F
+#define	CU_CTX_SHARED		0x00
+#define	CU_CTX_EXCLUSIVE	0x01
+
+/* Virtual CU index
+ * This is useful when there is no need to open a context on hardware CU,
+ * but still need to lockdown the xclbin.
+ */
+#define	CU_CTX_VIRT_CU		0xffffffff
+struct kds_ctx_info {
+	u32		  cu_domain;
+	u32		  cu_idx;
+	u32		  flags;
+	void		 *curr_ctx; // Holds the current context ptr for kds
+};
+
+/* TODO: PS kernel is very different with FPGA kernel.
+ * Let's see if we can unify them later.
+ */
+struct kds_scu_mgmt {
+	struct xrt_cu		 *xcus[MAX_CUS];
+	struct mutex		  lock;
+	int			  num_cus;
+	u32			  status[MAX_CUS];
+	char			  name[MAX_CUS][32];
+	u32			  cu_refs[MAX_CUS];
+	struct cu_stats __percpu *cu_stats;
+};
+
+/* the MSB of cu_refs is used for exclusive flag */
+#define CU_EXCLU_MASK		0x80000000
+struct kds_cu_mgmt {
+	struct xrt_cu		 *xcus[MAX_CUS];
+	struct mutex		  lock;
+	int			  num_cus;
+	int			  num_cdma;
+	u32			  cu_intr[MAX_CUS];
+	u32			  cu_refs[MAX_CUS];
+	struct cu_stats __percpu *cu_stats;
+	int			  rw_shared;
+};
+
+#define cu_stat_read(cu_mgmt, field) \
+	stat_read((cu_mgmt)->cu_stats, field)
+
+#define cu_stat_write(cu_mgmt, field, val) \
+	stat_write((cu_mgmt)->cu_stats, field, val)
+
+#define cu_stat_inc(cu_mgmt, field) \
+	this_stat_inc((cu_mgmt)->cu_stats, field)
+
+#define cu_stat_dec(cu_mgmt, field) \
+	this_stat_dec((cu_mgmt)->cu_stats, field)
+
+/* ERT core */
+struct kds_ert {
+	u32			slot_size;
+	void (* submit)(struct kds_ert *ert, struct kds_command *xcmd);
+	void (* abort)(struct kds_ert *ert, struct kds_client *client, int cu_idx);
+	bool (* abort_done)(struct kds_ert *ert, struct kds_client *client, int cu_idx);
+	bool (* abort_sync)(struct kds_ert *ert, struct kds_client *client, int cu_idx);
+};
+
+/* Fast adapter memory info */
+#define FA_MEM_MAX_SIZE 128 * 1024
+struct cmdmem_info {
+	/* This is use for free bo, do not use it in shared code */
+	void		       *bo;
+	u64			bar_paddr;
+	u64			dev_paddr;
+	void __iomem		*vaddr;
+	u32			size;
+};
+
+/**
+ * struct kds_sched: KDS scheduler manage CUs and client list.
+ *		     There should be only one KDS per device.
+ *
+ * @list_head: Client list
+ * @num_client: Number of clients
+ * @lock: Mutex to protect client list
+ * @cu_mgmt: hardware CUs management data structure
+ * @ert: remote scheduler
+ * @ert_disable: remote scheduler is disabled or not
+ * @xgq_enable: remote scheduler supports XGQ
+ * @cu_intr_cap: capbility of CU interrupt support
+ * @cu_intr: CU or ERT interrupt. 1 for CU, 0 for ERT.
+ * @anon_client: driver own kds client used with driver generated command
+ * @polling_thread: poll CUs when ERT is disabled
+ */
+#define KDS_SYSFS_SETTING_BIT	(1 << 31)
+#define KDS_SET_SYSFS_BIT(val)	(val | KDS_SYSFS_SETTING_BIT)
+#define KDS_SYSFS_SETTING(val)	(val & KDS_SYSFS_SETTING_BIT)
+#define KDS_SETTING(val)	(val & ~KDS_SYSFS_SETTING_BIT)
+struct kds_sched {
+	struct list_head	clients;
+	int			num_client;
+	struct mutex		lock;
+	bool			bad_state;
+	struct kds_cu_mgmt	cu_mgmt;
+	struct kds_scu_mgmt	scu_mgmt;
+	struct kds_ert	       *ert;
+	bool			xgq_enable;
+	u32			cu_intr_cap;
+	struct cmdmem_info	cmdmem;
+	struct completion	comp;
+	struct kds_client      *anon_client;
+
+	/* Settings */
+	bool			ini_disable;
+	bool			ert_disable;
+	u32			cu_intr;
+
+	/* KDS polling thread */
+	struct task_struct     *polling_thread;
+	struct list_head	alive_cus; /* alive CU list */
+	wait_queue_head_t	wait_queue;
+	int			polling_start;
+	int			polling_stop;
+	u32			interval;
+};
+
+int kds_init_sched(struct kds_sched *kds);
+int kds_init_ert(struct kds_sched *kds, struct kds_ert *ert);
+int kds_init_client(struct kds_sched *kds, struct kds_client *client);
+void kds_fini_sched(struct kds_sched *kds);
+int kds_fini_ert(struct kds_sched *kds);
+void kds_fini_client(struct kds_sched *kds, struct kds_client *client);
+void kds_reset(struct kds_sched *kds);
+int kds_cfg_update(struct kds_sched *kds);
+void kds_cus_irq_enable(struct kds_sched *kds, bool enable);
+int is_bad_state(struct kds_sched *kds);
+u32 kds_live_clients(struct kds_sched *kds, pid_t **plist);
+u32 kds_live_clients_nolock(struct kds_sched *kds, pid_t **plist);
+int kds_add_cu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_del_cu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_add_scu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_del_scu(struct kds_sched *kds, struct xrt_cu *xcu);
+int kds_get_cu_total(struct kds_sched *kds);
+u32 kds_get_cu_addr(struct kds_sched *kds, int idx);
+u32 kds_get_cu_proto(struct kds_sched *kds, int idx);
+int kds_get_max_regmap_size(struct kds_sched *kds);
+int kds_add_context(struct kds_sched *kds, struct kds_client *client,
+		    struct kds_ctx_info *info);
+int kds_del_context(struct kds_sched *kds, struct kds_client *client,
+		    struct kds_ctx_info *info);
+int kds_open_ucu(struct kds_sched *kds, struct kds_client *client, u32 cu_idx);
+int kds_map_cu_addr(struct kds_sched *kds, struct kds_client *client,
+		    int idx, unsigned long size, u32 *addrp);
+int kds_add_command(struct kds_sched *kds, struct kds_command *xcmd);
+/* Use this function in xclbin download flow for config commands */
+int kds_submit_cmd_and_wait(struct kds_sched *kds, struct kds_command *xcmd);
+
+struct kds_command *kds_alloc_command(struct kds_client *client, u32 size);
+
+void kds_free_command(struct kds_command *xcmd);
+int kds_ip_layout2cu_info(struct ip_layout *ip_layout, struct xrt_cu_info cu_info[], int num_info);
+int kds_ip_layout2scu_info(struct ip_layout *ip_layout, struct xrt_cu_info cu_info[], int num_info);
+
+/* sysfs */
+int store_kds_echo(struct kds_sched *kds, const char *buf, size_t count,
+		   int *echo);
+ssize_t show_kds_stat(struct kds_sched *kds, char *buf);
+ssize_t show_kds_custat_raw(struct kds_sched *kds, char *buf);
+ssize_t show_kds_scustat_raw(struct kds_sched *kds, char *buf);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/kds_stat.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/kds_stat.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver Scheduler
+ *
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _KDS_STAT_H
+#define _KDS_STAT_H
+
+#include <linux/percpu-defs.h>
+
+/* TODO: Using MAX_CUS in this header file is not ideal.
+ * This file eventually should be very independent.
+ * Let's remove all MAX_CUS from this file once we have chance.
+ */
+#ifndef MAX_CUS
+#define MAX_CUS 128
+#endif
+
+/* This header file defines statistics struct and macros to operates them.
+ * Percpu variable are used for performance concerns.
+ */
+
+struct client_stats {
+	/* Per CU counter that counts when a command is submitted to CU */
+	unsigned long		s_cnt[MAX_CUS];
+	/* Per CU counter that counts when a command is completed or error */
+	unsigned long		c_cnt[MAX_CUS];
+	/* Per soft CU counter that counts when a command is submitted to SCU */
+	unsigned long		scu_s_cnt[MAX_CUS];
+	/* Per soft CU counter that counts when a command is completed or error */
+	unsigned long		scu_c_cnt[MAX_CUS];
+};
+
+struct cu_stats {
+	u64		  usage[MAX_CUS];
+};
+
+/*
+ * Macros to operates on percpu statistics:
+ * this_cpu_* are operations with implied preemption/interrupt protection.
+ */
+#define this_stat_get(statp, field) \
+	this_cpu_read((statp)->field)
+
+#define this_stat_set(statp, field, val) \
+	this_cpu_write((statp)->field, val)
+
+#define this_stat_inc(statp, field) \
+	this_cpu_add((statp)->field, 1)
+
+#define this_stat_dec(statp, field) \
+	this_cpu_add((statp)->field, -1)
+
+#define stat_read(statp, field)					\
+({								\
+	typeof((statp)->field) res = 0;				\
+	unsigned int _cpu;					\
+	for_each_possible_cpu(_cpu)				\
+		res += per_cpu_ptr((statp), _cpu)->field;	\
+	res;							\
+})
+
+#define stat_write(statp, field, val)				\
+({								\
+	unsigned int _cpu;					\
+	for_each_possible_cpu(_cpu)				\
+		per_cpu_ptr((statp), _cpu)->field = val;	\
+})
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/ps_kernel.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/ps_kernel.h
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2021 Xilinx, Inc
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"). You may
+ * not use this file except in compliance with the License. A copy of the
+ * License is located at
+ *
+ *		 http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ */
+
+#ifndef _PS_KERNEL_H_
+#define _PS_KERNEL_H_
+
+/*
+ * This header file contains data structure for xrt PS kernel metadata. This
+ * file is included in user space utilities and kernel drivers. The data
+ * structure is used to describe PS kernel which is written by driver
+ * and read by utility.
+ */
+
+#define	PS_KERNEL_NAME_LENGTH	20
+#define	PS_KERNEL_REG_OFFSET	4
+
+struct ps_kernel_data {
+	char		pkd_sym_name[PS_KERNEL_NAME_LENGTH];
+	uint32_t	pkd_num_instances;
+};
+
+struct ps_kernel_node {
+	uint32_t		pkn_count;
+	struct ps_kernel_data	pkn_data[1];
+};
+
+#endif /* _PS_KERNEL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/sched_exec.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/sched_exec.h
@@ -0,0 +1,315 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Compute unit execution, interrupt management and
+ * client context core data structures.
+ *
+ * Copyright (C) 2017-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XCL_SCHE_EXEC_H_
+#define _XCL_SCHE_EXEC_H_
+
+#include <linux/mutex.h>
+#include <linux/init_task.h>
+#include <linux/list.h>
+#include <linux/wait.h>
+#include "zocl_drv.h"
+#include "zocl_cu.h"
+#include "ert.h"
+
+#define MAX_SLOTS 128
+#define MAX_U32_SLOT_MASKS (((MAX_SLOTS-1)>>5) + 1)
+/* MAX_CU_NUM are defined in zocl_util.h */
+#define MAX_U32_CU_MASKS (((MAX_CU_NUM-1)>>5) + 1)
+
+/* Timer thread wake up interval in Millisecond */
+#define	ZOCL_CU_TIMER_INTERVAL		(500)
+
+/* Reset timer interval in Microsecond */
+#define	ZOCL_CU_RESET_TIMER_INTERVAL	(1000)
+
+/*
+ * For zocl cu version 1. The done counter will have risk to overflow
+ * if more than 31 commands done but kds still not able to read done counter.
+ * TBD. This is related to the hardware implementation.
+ */
+#define MAX_PENDING_CMD         31
+
+/**
+ * Timestamp only use in set_cmd_ext_timestamp()
+ */
+enum zocl_ts_type {
+	CU_START_TIME,
+	CU_DONE_TIME,
+};
+
+enum zocl_cu_type {
+	ZOCL_HARD_CU,
+	ZOCL_SOFT_CU,
+};
+
+enum zocl_exec_status {
+	ZOCL_EXEC_NORMAL = 0,
+	ZOCL_EXEC_STOP,
+	ZOCL_EXEC_FLUSH,
+};
+
+struct sched_dev;
+struct sched_ops;
+
+/*
+ * struct sched_client_ctx: Manage user space client attached to device
+ *
+ * @link: Client context is added to list in device
+ * @trigger: Poll wait counter for number of completed exec buffers
+ * @outstanding_execs: Counter for number outstanding exec buffers
+ * @lock: Mutex lock for exclusive access
+ * @num_cus: Number of resources (CUs) explcitly acquired
+ * @pid: process ID that this context belongs to
+ * @abort: Flag to indicate that this context has detached from user space
+ * @shcus: CUs shared reserved by this context
+ * @excus: CUs exclusively reserved by this context
+ * @graph_list: Graphs that this client opens are added to this list.
+ * @graph_list_lock: Graph list lock.
+ * @aie_ctx: The AIE context acquired.
+ */
+struct sched_client_ctx {
+	struct list_head   link;
+	atomic_t           trigger;
+	atomic_t           outstanding_execs;
+	struct mutex       lock;
+	int		   num_cus;
+	struct pid	   *pid;
+	unsigned int	   abort;
+	DECLARE_BITMAP(shcus, MAX_CU_NUM);
+	DECLARE_BITMAP(excus, MAX_CU_NUM);
+
+	struct list_head   graph_list;
+	spinlock_t         graph_list_lock;
+	u32                aie_ctx;
+};
+#define CLIENT_NUM_CU_CTX(client) ((client)->num_cus)
+
+/**
+ * struct sched_exec_core: Core data structure for command execution on a device
+ *
+ * @ctx_list: Context list populated with device context
+ * @ctx_list_lock: Context list lock
+ * @poll_wait_queue: Wait queue for device polling
+ * @scheduler: Command queue scheduler
+ * @submitted_cmds: Tracking of command submitted for execution on this device
+ * @num_slots: Number of command queue slots
+ * @num_cus: Number of CUs in loaded program
+ * @cu_shift_offset: CU idx to CU address shift value
+ * @cu_base_addr: Base address of CU address space
+ * @polling_mode: If set then poll for command completion
+ * @cq_interrupt: If set then X86 host will trigger interrupt to PS
+ * @configured: Flag of the core data structure has been initialized
+ * @slot_status: Status (busy(1)/free(0)) of slots in command queue
+ * @num_slot_masks: Number of slots status masks used
+ * @cu_status: Status (busy(1)/free(0)) of CUs. Unused in ERT mode.
+ * @num_cu_masks: Number of CU masks used (computed from @num_cus)
+ * @cu_addr_phy: Physical address of CUs.
+ * @cu: Per CU structure.
+ * @ops: Scheduler operations vtable
+ * @cq_thread: Kernel thread to check the ert command queue.
+ * @timer_task: Kernel thread as a timer interrupt.
+ */
+struct sched_exec_core {
+	void __iomem               *base;
+	struct list_head           ctx_list;
+	spinlock_t                 ctx_list_lock;
+	wait_queue_head_t          poll_wait_queue;
+
+	struct scheduler          *scheduler;
+
+	struct sched_cmd          *submitted_cmds[MAX_SLOTS];
+
+	unsigned int               num_slots;
+	unsigned int               num_cus;
+	unsigned int               cu_shift_offset;
+	u32                        cu_base_addr;
+	unsigned int               polling_mode;
+	unsigned int               cq_interrupt;
+	unsigned int               cu_dma;
+	unsigned int               cu_isr;
+	unsigned int               configured;
+
+
+	/* Bitmap tracks busy(1)/free(0) slots in cmd_slots*/
+	u32                        slot_status[MAX_U32_SLOT_MASKS];
+	unsigned int               num_slot_masks; /* ((num_slots-1)>>5)+1 */
+
+	/* Bitmap tracks CU busy(1)/free(0) */
+	u32                        cu_status[MAX_U32_CU_MASKS];
+	unsigned int               num_cu_masks; /* ((num_cus-1)>>5+1 */
+
+	/* Bitmap tracks CU initialization initialized(1)/uninitialized(0) */
+	u32                        cu_init[MAX_U32_CU_MASKS];
+
+	/* Soft kernel definitions */
+	u32                        scu_status[MAX_U32_CU_MASKS];
+
+	/* Bitmap tracks valid CU valid(1)/invalid(0) */
+	u32			   cu_valid[MAX_U32_CU_MASKS];
+
+	struct zocl_cu		  *zcu;
+
+	struct sched_ops          *ops;
+	struct task_struct        *cq_thread;
+	wait_queue_head_t          cq_wait_queue;
+	atomic_t                   cq_intc;
+
+	struct task_struct        *timer_task;
+
+	/* Context switch */
+	atomic_t		  exec_status;
+
+	/*
+	 * Watchdog thread monitoring the state of skd/cmc/cq/sched.
+	 * This is only working in ert mode. And in this mode, kds mode
+	 * is not working, which means there is no handling thread per cu.
+	 * In the future if per thread cu is enabled, since those threads
+	 * are created after xclbin is loaded, we may need a list to
+	 * maitain all of the thread to be monitored.
+	 */
+	struct task_struct      *watchdog_thread;
+};
+
+/**
+ * struct scheduler: scheduler for sched_cmd objects
+ *
+ * @sched_thread: thread associated with this scheduler
+ * @use_count: use count for this scheduler
+ * @wait_queue: conditional wait queue for scheduler thread
+ * @error: set to 1 to indicate scheduler error
+ * @stop: set to 1 to indicate scheduler should stop
+ * @cq: list of command objects managed by scheduler
+ * @intc: set when there is a pending interrupt for command completion
+ * @poll: number of running commands in polling mode
+ * @check: flag to indicate a CU timerout check
+ */
+struct scheduler {
+	struct task_struct        *sched_thread;
+	unsigned int               use_count;
+	// KDS CMD Stats
+	atomic_t 		   num_pending;
+	atomic_t 		   num_running;
+	atomic_t 		   num_received;
+	atomic_t 		   num_notified;
+
+	wait_queue_head_t          wait_queue;
+	unsigned int               error;
+	unsigned int               stop;
+
+	struct list_head           cq;
+	unsigned int               intc; /* pending intr shared with isr*/
+	unsigned int               poll; /* number of cmds to poll */
+	atomic_t                   check;
+};
+
+/**
+ * Command data used by scheduler
+ *
+ * @list: command object moves from list to list
+ * @exec: core data structure for scheduler
+ * @state: state of command object per scheduling
+ * @cu_idx: index of CU executing this cmd object; used in penguin mode only
+ * @slot_idx: command queue index of this command object
+ * @buffer: underlying buffer (ex. drm buffer object)
+ * @exectime: time unit elapsed after CU is triggered to run
+ * @packet: mapped ert packet object from user space
+ * @check_timeout: flag to indicate if we should check timeout on this CU
+ */
+struct sched_cmd {
+	struct list_head list;
+	struct list_head rq_list;
+	struct drm_device *ddev;
+	struct scheduler *sched;
+	struct sched_exec_core *exec;
+	struct sched_client_ctx *client;
+	enum ert_cmd_state state;
+	int cu_idx; /* running cu, initialized to -1 */
+	uint32_t slot_idx;
+	uint32_t cq_slot_idx;
+	void *buffer;
+	void (*free_buffer)(struct sched_cmd *xcmd);
+
+	/*
+	 * This is a rough time unit elapsed after the CU is running.
+	 * It is set to a initial value configured by init CU command
+	 * and decreased every time unit. If it reaches zero, this CU
+	 * timeouts.
+	 *
+	 * The time unit is 500 Milliseconds now.
+	 */
+	uint32_t exectime;
+
+	/*
+	 * If this flag is set, we should check the timeout of this
+	 * command. It is set based on the CU timeout value. If the
+	 * timeout value is 0, we should not set this flag.
+	 */
+	int check_timeout;
+
+	/*
+	 * If this flag is set, record time stamps in the user's command
+	 * package when the command state change.
+	 */
+	bool timestamp_enabled;
+
+	/* The actual cmd object representation */
+	union {
+		struct ert_packet *packet;
+		struct ert_start_copybo_cmd *ert_cp;
+		struct ert_start_kernel_cmd *ert_cu;
+	};
+
+	zocl_dma_handle_t dma_handle;
+};
+
+/**
+ * struct sched_ops: scheduler specific operations
+ *
+ * Scheduler can operate in MicroBlaze mode (mb/ert) or in penguin mode. This
+ * struct differentiates specific operations.  The struct is per device node,
+ * meaning that one device can operate in ert mode while another can operate in
+ * penguin mode.
+ */
+struct sched_ops {
+	int (*submit)(struct sched_cmd *xcmd);
+	void (*query)(struct sched_cmd *xcmd);
+};
+
+int sched_init_exec(struct drm_device *drm);
+int sched_fini_exec(struct drm_device *drm);
+int sched_reset_exec(struct drm_device *drm);
+int sched_reset_scheduler(struct drm_device *drm);
+
+
+int sched_xclbin_ctx(struct drm_zocl_dev *zdev, struct drm_zocl_ctx *ctx,
+		                        struct sched_client_ctx *client);
+int sched_context_ioctl(struct drm_zocl_dev *zdev, void *data,
+			                struct drm_file *filp);
+int sched_poll_client(struct file *filp, poll_table *wait);
+int sched_create_client(struct drm_device *dev, void **priv);
+void sched_destroy_client(struct drm_device *dev, void **priv);
+
+void zocl_track_ctx(struct drm_device *dev, struct sched_client_ctx *fpriv);
+void zocl_untrack_ctx(struct drm_device *dev, struct sched_client_ctx *fpriv);
+
+int zocl_exec_valid_cu(struct sched_exec_core *exec, unsigned int cuid);
+u32 sched_is_busy(struct drm_zocl_dev *zdev);
+u32 sched_live_clients(struct drm_zocl_dev *zdev, pid_t **plist);
+int sched_attach_cu(struct drm_zocl_dev *zdev, u32 cu_idx);
+int sched_detach_cu(struct drm_zocl_dev *zdev, u32 cu_idx);
+int zocl_execbuf_exec(struct drm_device *dev, void *data,
+		      struct drm_file *filp);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/types.h
@@ -0,0 +1,25 @@
+/**
+ * Copyright (C) 2019 Xilinx, Inc
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"). You may
+ * not use this file except in compliance with the License. A copy of the
+ * License is located at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ */
+
+#ifndef core_include_types_h_
+#define core_include_types_h_
+
+#if defined(_WIN32)
+# include "windows/types.h"
+# include "windows/uuid.h"
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xclbin.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xclbin.h
@@ -0,0 +1,569 @@
+/**
+ *  Copyright (C) 2015-2022, Xilinx Inc
+ *  Copyright (C) 2022 Advanced Micro Devices, Inc.
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 3 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ */
+
+#ifndef _XCLBIN_H_
+#define _XCLBIN_H_
+
+#ifdef _WIN32
+  #include <cstdint>
+  #include <algorithm>
+  #include "windows/uuid.h"
+#else
+  #if defined(__KERNEL__)
+    #include <linux/types.h>
+    #include <linux/uuid.h>
+    #include <linux/version.h>
+  #elif defined(__cplusplus)
+    #include <cstdlib>
+    #include <cstdint>
+    #include <algorithm>
+    #include <uuid/uuid.h>
+  #else
+    #include <stdlib.h>
+    #include <stdint.h>
+    #include <uuid/uuid.h>
+  #endif
+
+  #if !defined(__KERNEL__)
+    typedef uuid_t xuid_t;
+  #else //(__KERNEL__)
+    #if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 12, 0)
+      typedef uuid_t xuid_t;
+    #elif defined(RHEL_RELEASE_CODE)
+      #if RHEL_RELEASE_CODE > RHEL_RELEASE_VERSION(7,4)
+        typedef uuid_t xuid_t;
+      #else
+        typedef uuid_le xuid_t;
+      #endif
+    #else
+      typedef uuid_le xuid_t;
+    #endif
+  #endif
+#endif
+
+// ----------------- Custom Assert Macro -------------------------
+// The xclbin.h header file is used both by the driver and host
+// applications/libraries.  For C++ static_assert() would be used, but
+// for the the drivers (e.g., linux) a more custom solution is needed
+// e.g., BUILD_BUG_ON_ZERO()).  Instead of creating a wrapper around the
+// various OS builds, a custom assert (based on the linux assert) is used.
+
+#ifdef __cplusplus
+  // Used C++ static assert
+  #define XCLBIN_STATIC_ASSERT(e,m) \
+    static_assert (e, m)
+#else
+  // Use our "custom" kernel compilation assert
+  #define XLCBIN_ASSERT_CONCAT_(a, b) a##b
+  #define XLCBIN_ASSERT_CONCAT(a, b) XLCBIN_ASSERT_CONCAT_(a, b)
+
+  // Create an artifitial assertion via a bad divide by zero assertion.
+  #define XCLBIN_STATIC_ASSERT(e,m) \
+    enum { XLCBIN_ASSERT_CONCAT(assert_line_, __LINE__) = 1/(int)(!!(e)) }
+#endif
+
+// Reports a size of structure via an error
+#define SIZE_OF_STRUCT(s) \
+   char (*__fail)[sizeof(struct s)] = 1
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+    /**
+     * Container format for Xilinx bitstreams, metadata and other
+     * binary blobs.
+     * Every segment must be aligned at 8 byte boundary with null byte padding
+     * between adjacent segments if required.
+     * For segements which are not present both offset and length must be 0 in
+     * the header.
+     * Currently only xclbin0\0 is recognized as file magic. In future if/when file
+     * format is updated the magic string will be changed to xclbin1\0 and so on.
+     */
+    enum XCLBIN_MODE {
+        XCLBIN_FLAT,
+        XCLBIN_PR,
+        XCLBIN_TANDEM_STAGE2,
+        XCLBIN_TANDEM_STAGE2_WITH_PR,
+        XCLBIN_HW_EMU,
+        XCLBIN_SW_EMU,
+        XCLBIN_HW_EMU_PR,
+        XCLBIN_MODE_MAX
+    };
+
+    /*
+     *  AXLF LAYOUT
+     *  -----------
+     *
+     *  -----------------------------------------
+     *  | Magic                                 |
+     *  -----------------------------------------
+     *  | Header                                |
+     *  -----------------------------------------
+     *  | One or more section headers           |
+     *  -----------------------------------------
+     *  | Matching number of sections with data |
+     *  -----------------------------------------
+     *
+     */
+
+    enum axlf_section_kind {
+        BITSTREAM              =  0,
+        CLEARING_BITSTREAM     =  1,
+        EMBEDDED_METADATA      =  2,
+        FIRMWARE               =  3,
+        DEBUG_DATA             =  4,
+        SCHED_FIRMWARE         =  5,
+        MEM_TOPOLOGY           =  6,
+        CONNECTIVITY           =  7,
+        IP_LAYOUT              =  8,
+        DEBUG_IP_LAYOUT        =  9,
+        DESIGN_CHECK_POINT     = 10,
+        CLOCK_FREQ_TOPOLOGY    = 11,
+        MCS                    = 12,
+        BMC                    = 13,
+        BUILD_METADATA         = 14,
+        KEYVALUE_METADATA      = 15,
+        USER_METADATA          = 16,
+        DNA_CERTIFICATE        = 17,
+        PDI                    = 18,
+        BITSTREAM_PARTIAL_PDI  = 19,
+        PARTITION_METADATA     = 20,
+        EMULATION_DATA         = 21,
+        SYSTEM_METADATA        = 22,
+        SOFT_KERNEL            = 23,
+        ASK_FLASH              = 24,
+        AIE_METADATA           = 25,
+        ASK_GROUP_TOPOLOGY     = 26,
+        ASK_GROUP_CONNECTIVITY = 27,
+        SMARTNIC               = 28,
+        AIE_RESOURCES          = 29,
+        OVERLAY                = 30,
+        VENDER_METADATA        = 31,
+    };
+
+    enum MEM_TYPE {
+        MEM_DDR3,
+        MEM_DDR4,
+        MEM_DRAM,
+        MEM_STREAMING,
+        MEM_PREALLOCATED_GLOB,
+        MEM_ARE, //Aurora
+        MEM_HBM,
+        MEM_BRAM,
+        MEM_URAM,
+        MEM_STREAMING_CONNECTION,
+        MEM_HOST,
+        MEM_PS_KERNEL,
+    };
+
+    enum IP_TYPE {
+        IP_MB = 0,
+        IP_KERNEL, //kernel instance
+        IP_DNASC,
+        IP_DDR4_CONTROLLER,
+        IP_MEM_DDR4,
+        IP_MEM_HBM,
+        IP_MEM_HBM_ECC,
+        IP_PS_KERNEL,
+    };
+
+    enum ACTION_MASK {
+      AM_LOAD_AIE = 0x1                     /* Indicates to the driver to load the AIE PID section */
+    };
+
+    struct axlf_section_header {
+        uint32_t m_sectionKind;             /* Section type */
+        char m_sectionName[16];             /* Examples: "stage2", "clear1", "clear2", "ocl1", "ocl2, "ublaze", "sched" */
+        uint64_t m_sectionOffset;           /* File offset of section data */
+        uint64_t m_sectionSize;             /* Size of section data */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct axlf_section_header) == 40, "axlf_section_header structure no longer is 40 bytes in size");
+
+    struct axlf_header {
+        uint64_t m_length;                  /* Total size of the xclbin file */
+        uint64_t m_timeStamp;               /* Number of seconds since epoch when xclbin was created */
+        uint64_t m_featureRomTimeStamp;     /* TimeSinceEpoch of the featureRom */
+        uint16_t m_versionPatch;            /* Patch Version */
+        uint8_t m_versionMajor;             /* Major Version - Version: 2.1.0*/
+        uint8_t m_versionMinor;             /* Minor Version */
+        uint16_t m_mode;                    /* XCLBIN_MODE */
+        uint16_t m_actionMask;              /* Bit Mask */
+	union {
+	    struct {
+		uint64_t m_platformId;      /* 64 bit platform ID: vendor-device-subvendor-subdev */
+		uint64_t m_featureId;       /* 64 bit feature id */
+	    } rom;
+	    unsigned char rom_uuid[16];     /* feature ROM UUID for which this xclbin was generated */
+	};
+        unsigned char m_platformVBNV[64];   /* e.g. xilinx:xil-accel-rd-ku115:4ddr-xpr:3.4: null terminated */
+	union {
+	    char m_next_axlf[16];           /* Name of next xclbin file in the daisy chain */
+	    xuid_t uuid;                    /* uuid of this xclbin*/
+	};
+        char m_debug_bin[16];               /* Name of binary with debug information */
+        uint32_t m_numSections;             /* Number of section headers */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct axlf_header) == 152, "axlf_header structure no longer is 152 bytes in size");
+    #define XCLBIN_MAX_NUM_SECTION    0x10000
+
+    struct axlf {
+        char m_magic[8];                            /* Should be "xclbin2\0"  */
+        int32_t m_signature_length;                 /* Length of the signature. -1 indicates no signature */
+        unsigned char reserved[28];                 /* Note: Initialized to 0xFFs */
+
+        unsigned char m_keyBlock[256];              /* Signature for validation of binary */
+        uint64_t m_uniqueId;                        /* axlf's uniqueId, use it to skip redownload etc */
+        struct axlf_header m_header;                /* Inline header */
+        struct axlf_section_header m_sections[1];   /* One or more section headers follow */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct axlf) == 496, "axlf structure no longer is 496 bytes in size");
+
+    typedef struct axlf xclBin;
+
+    /**** BEGIN : Xilinx internal section *****/
+
+    /* bitstream information */
+    struct xlnx_bitstream {
+        uint8_t m_freq[8];
+        char bits[1];
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct xlnx_bitstream) == 9, "xlnx_bitstream structure no longer is 9 bytes in size");
+
+
+    /****   MEMORY TOPOLOGY SECTION ****/
+    struct mem_data {
+        uint8_t m_type;          // enum corresponding to mem_type.
+        uint8_t m_used;          // if 0 this bank is not present
+        uint8_t padding[6];      // 8 Byte alignment padding (initialized to zeros)
+        union {
+            uint64_t m_size;     // if mem_type DDR, then size in KB;
+            uint64_t route_id;   // if streaming then "route_id"
+        };
+        union {
+            uint64_t m_base_address; // if DDR then the base address;
+            uint64_t flow_id;        // if streaming then "flow id"
+        };
+        unsigned char m_tag[16]; // DDR: BANK0,1,2,3, has to be null terminated; if streaming then stream0, 1 etc
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct mem_data) == 40, "mem_data structure no longer is 40 bytes in size");
+
+    struct mem_topology {
+        int32_t m_count; //Number of mem_data
+        struct mem_data m_mem_data[1]; //Should be sorted on mem_type
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct mem_topology) == 48, "mem_topology structure no longer is 48 bytes in size");
+
+
+    /****   CONNECTIVITY SECTION ****/
+    /* Connectivity of each argument of Kernel. It will be in terms of argument
+     * index associated. For associating kernel instances with arguments and
+     * banks, start at the connectivity section. Using the m_ip_layout_index
+     * access the ip_data.m_name. Now we can associate this kernel instance
+     * with its original kernel name and get the connectivity as well. This
+     * enables us to form related groups of kernel instances.
+     */
+
+    struct connection {
+        int32_t arg_index; //From 0 to n, may not be contiguous as scalars skipped
+        int32_t m_ip_layout_index; //index into the ip_layout section. ip_layout.m_ip_data[index].m_type == IP_KERNEL
+        int32_t mem_data_index; //index of the m_mem_data . Flag error is m_used false.
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct connection) == 12, "connection structure no longer is 12 bytes in size");
+
+    struct connectivity {
+        int32_t m_count;
+        struct connection m_connection[1];
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct connectivity) == 16, "connectivity structure no longer is 16 bytes in size");
+
+    /****   IP_LAYOUT SECTION ****/
+
+    // IP Kernel
+    #define IP_INT_ENABLE_MASK    0x0001
+    #define IP_INTERRUPT_ID_MASK  0x00FE
+    #define IP_INTERRUPT_ID_SHIFT 0x1
+
+    enum IP_CONTROL {
+        AP_CTRL_HS = 0,
+        AP_CTRL_CHAIN = 1,
+        AP_CTRL_NONE = 2,
+        AP_CTRL_ME = 3,
+        ACCEL_ADAPTER = 4,
+        FAST_ADAPTER = 5
+    };
+
+    #define IP_CONTROL_MASK  0xFF00
+    #define IP_CONTROL_SHIFT 0x8
+
+    /* IPs on AXI lite - their types, names, and base addresses.*/
+    struct ip_data {
+        uint32_t m_type; //map to IP_TYPE enum
+        union {
+            uint32_t properties; // Default: 32-bits to indicate ip specific property.
+                                 // m_type: IP_KERNEL
+                                 //         m_int_enable   : Bit  - 0x0000_0001;
+                                 //         m_interrupt_id : Bits - 0x0000_00FE;
+                                 //         m_ip_control   : Bits = 0x0000_FF00;
+            struct {             // m_type: IP_MEM_*
+               uint16_t m_index;
+               uint8_t m_pc_index;
+               uint8_t unused;
+            } indices;
+        };
+        uint64_t m_base_address;
+        uint8_t m_name[64]; //eg Kernel name corresponding to KERNEL instance, can embed CU name in future.
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct ip_data) == 80, "ip_data structure no longer is 80 bytes in size");
+
+    struct ip_layout {
+        int32_t m_count;
+        struct ip_data m_ip_data[1]; //All the ip_data needs to be sorted by m_base_address.
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct ip_layout) == 88, "ip_layout structure no longer is 88 bytes in size");
+
+    /*** Debug IP section layout ****/
+    enum DEBUG_IP_TYPE {
+        UNDEFINED = 0,
+        LAPC,
+        ILA,
+        AXI_MM_MONITOR,
+        AXI_TRACE_FUNNEL,
+        AXI_MONITOR_FIFO_LITE,
+        AXI_MONITOR_FIFO_FULL,
+        ACCEL_MONITOR,
+        AXI_STREAM_MONITOR,
+        AXI_STREAM_PROTOCOL_CHECKER,
+        TRACE_S2MM,
+        AXI_DMA,
+        TRACE_S2MM_FULL,
+        AXI_NOC,
+        ACCEL_DEADLOCK_DETECTOR,
+        DEBUG_IP_TYPE_MAX
+    };
+
+    struct debug_ip_data {
+        uint8_t m_type; // type of enum DEBUG_IP_TYPE
+        uint8_t m_index_lowbyte;
+        uint8_t m_properties;
+        uint8_t m_major;
+        uint8_t m_minor;
+        uint8_t m_index_highbyte;
+        uint8_t m_reserved[2];
+        uint64_t m_base_address;
+        char    m_name[128];
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct debug_ip_data) == 144, "debug_ip_data structure no longer is 144 bytes in size");
+
+    struct debug_ip_layout {
+        uint16_t m_count;
+        struct debug_ip_data m_debug_ip_data[1];
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct debug_ip_layout) == 152, "debug_ip_layout structure no longer is 152 bytes in size");
+
+    enum CLOCK_TYPE {                      /* Supported clock frequency types */
+        CT_UNUSED = 0,                     /* Initialized value */
+        CT_DATA   = 1,                     /* Data clock */
+        CT_KERNEL = 2,                     /* Kernel clock */
+        CT_SYSTEM = 3                      /* System Clock */
+    };
+
+    struct clock_freq {                    /* Clock Frequency Entry */
+        uint16_t m_freq_Mhz;               /* Frequency in MHz */
+        uint8_t m_type;                    /* Clock type (enum CLOCK_TYPE) */
+        uint8_t m_unused[5];               /* Not used - padding */
+        char m_name[128];                  /* Clock Name */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct clock_freq) == 136, "clock_freq structure no longer is 136 bytes in size");
+
+    struct clock_freq_topology {           /* Clock frequency section */
+        int16_t m_count;                   /* Number of entries */
+        struct clock_freq m_clock_freq[1]; /* Clock array */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct clock_freq_topology) == 138, "clock_freq_topology structure no longer is 138 bytes in size");
+
+    enum MCS_TYPE {                        /* Supported MCS file types */
+        MCS_UNKNOWN = 0,                   /* Initialized value */
+        MCS_PRIMARY = 1,                   /* The primary mcs file data */
+        MCS_SECONDARY = 2,                 /* The secondary mcs file data */
+    };
+
+    struct mcs_chunk {                     /* One chunk of MCS data */
+        uint8_t m_type;                    /* MCS data type */
+        uint8_t m_unused[7];               /* padding */
+        uint64_t m_offset;                 /* data offset from the start of the section */
+        uint64_t m_size;                   /* data size */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct mcs_chunk) == 24, "mcs_chunk structure no longer is 24 bytes in size");
+
+    struct mcs {                           /* MCS data section */
+        int8_t m_count;                    /* Number of chunks */
+        int8_t m_unused[7];                /* padding */
+        struct mcs_chunk m_chunk[1];       /* MCS chunks followed by data */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct mcs) == 32, "mcs structure no longer is 32 bytes in size");
+
+    struct bmc {                           /* bmc data section  */
+        uint64_t m_offset;                 /* data offset from the start of the section */
+        uint64_t m_size;                   /* data size (bytes)*/
+        char m_image_name[64];             /* Name of the image (e.g., MSP432P401R) */
+        char m_device_name[64];            /* Device ID         (e.g., VCU1525)  */
+        char m_version[64];
+        char m_md5value[33];               /* MD5 Expected Value(e.g., 56027182079c0bd621761b7dab5a27ca)*/
+        char m_padding[7];                 /* Padding */
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct bmc) == 248, "bmc structure no longer is 248 bytes in size");
+
+    struct soft_kernel {                   /* soft kernel data section  */
+        // Prefix Syntax:
+        //   mpo - member, pointer, offset
+        //     This variable represents a zero terminated string
+        //     that is offseted from the beginning of the section.
+        //
+        //     The pointer to access the string is initialized as follows:
+        //     char * pCharString = (address_of_section) + (mpo value)
+        uint32_t mpo_name;         // Name of the soft kernel
+        uint32_t m_image_offset;   // Image offset
+        uint32_t m_image_size;     // Image size
+        uint32_t mpo_version;      // Version
+        uint32_t mpo_md5_value;    // MD5 checksum
+        uint32_t mpo_symbol_name;  // Symbol name
+        uint32_t m_num_instances;  // Number of instances
+        uint8_t padding[36];       // Reserved for future use
+        uint8_t reservedExt[16];   // Reserved for future extended data
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct soft_kernel) == 80, "soft_kernel structure no longer is 80 bytes in size");
+
+    enum FLASH_TYPE
+    {
+        FLT_UNKNOWN = 0,
+        FLT_BIN_PRIMARY
+    };
+
+    struct flash {                 /* flash data section  */
+        // Prefix Syntax:
+        //   mpo - member, pointer, offset
+        //     This variable represents a zero terminated string
+        //     that is offseted from the beginning of the section.
+        //
+        //     The pointer to access the string is initialized as follows:
+        //     char * pCharString = (address_of_section) + (mpo value)
+        uint16_t m_flash_type;     // ENUM FLASH_TYPE
+        uint8_t padding[2];        // Alignment buffer
+        uint32_t m_image_offset;   // Image offset
+        uint32_t m_image_size;     // Image size
+        uint32_t mpo_name;         // Name of the flash image
+        uint32_t mpo_version;      // Version
+        uint32_t mpo_md5_value;    // MD5 checksum
+        uint8_t reserved[32];      // Reserved for future use
+        uint8_t reservedExt[16];   // Reserved for future extended data
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct flash) == 72, "flash structure no longer is 72 bytes in size");
+
+    enum CHECKSUM_TYPE
+    {
+        CST_UNKNOWN = 0,
+        CST_SDBM = 1,
+        CST_LAST
+    };
+
+    struct vender_metadata {                   /* vender metadata section  */
+        // Prefix Syntax:
+        //   mpo - member, pointer, offset
+        //     This variable represents a zero terminated string
+        //     that is offseted from the beginning of the section.
+        //
+        //     The pointer to access the string is initialized as follows:
+        //     char * pCharString = (address_of_section) + (mpo value)
+        uint32_t mpo_name;         // Name of the the vender metadata section
+        uint32_t m_image_offset;   // Image offset
+        uint32_t m_image_size;     // Image size
+        uint8_t padding[36];       // Reserved for future use
+    };
+    XCLBIN_STATIC_ASSERT(sizeof(struct vender_metadata) == 48, "vender metadata kernel structure no longer is 48 bytes in size");
+
+    /**** END : Xilinx internal section *****/
+
+# ifdef __cplusplus
+    namespace xclbin {
+      inline const axlf_section_header*
+      get_axlf_section(const axlf* top, axlf_section_kind kind)
+      {
+        auto begin = top->m_sections;
+        auto end = begin + top->m_header.m_numSections;
+        auto itr = std::find_if(begin,end,[kind](const axlf_section_header& sec) { return sec.m_sectionKind == static_cast<uint32_t>(kind); });
+        return (itr!=end) ? &(*itr) : nullptr;
+      }
+
+      // Helper C++ section iteration
+      // To keep with with the current "coding" them, the function get_axlf_section_next() was
+      // introduced find 'next' common section names.
+      //
+      // Future TODO: Create a custom iterator and refactor the code base to use it.
+      //
+      // Example on how this function may be used:
+      //
+      // const axlf_section_header * pSection;
+      // const axlf* top = <xclbin image in memory>;
+      // for (pSection = xclbin::get_axlf_section( top, SOFT_KERNEL);
+      //      pSection != nullptr;
+      //      pSection = xclbin::get_axlf_section_next( top, pSection, SOFT_KERNEL)) {
+      //   <code to do work>
+      // }
+      inline const axlf_section_header*
+      get_axlf_section_next(const axlf* top, const axlf_section_header* current_section, axlf_section_kind kind)
+      {
+        if (top == nullptr) { return nullptr; }
+        if (current_section == nullptr) { return nullptr; }
+
+        auto end = top->m_sections + top->m_header.m_numSections;
+
+        auto begin = current_section + 1;        // Point to the next section
+        if (begin == end) { return nullptr; }
+
+        auto itr = std::find_if(begin, end, [kind](const axlf_section_header &sec) {return sec.m_sectionKind == static_cast<uint32_t>(kind); });
+        return (itr!=end) ? &(*itr) : nullptr;
+      }
+    }
+# endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xclerr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xclerr.h
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2017 Xilinx, Inc
+ * Author: Umang Parekh
+ *
+ * This file is dual licensed.  It may be redistributed and/or modified
+ * under the terms of the Apache 2.0 License OR version 2 of the GNU
+ * General Public License.
+ *
+ * Apache License Verbiage
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"). You may
+ * not use this file except in compliance with the License. A copy of the
+ * License is located at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ * GPL license Verbiage:
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the Free Software Foundation;
+ * either version 2 of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+ * without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ * See the GNU General Public License for more details.
+ * You should have received a copy of the GNU General Public License along with this program;
+ * if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+/**
+ * DOC: Device error status related structs and defines
+ * This file is used by both userspace and xclmgmt kernel driver.
+ */
+
+#ifndef XCLERR_H_
+#define XCLERR_H_
+
+/**
+ * enum xclFirewallID - AXI Firewall IDs used to identify individual AXI Firewalls
+ *
+ * @XCL_FW_MGMT_CONTROL:  MGMT BAR AXI-Lite BAR access protection
+ * @XCL_FW_USER_CONTROL:  USER BAR AXI-Lite BAR access protection
+ * @XCL_FW_DATAPATH:      DMA data path protection
+ */
+enum xclFirewallID {
+        XCL_FW_MGMT_CONTROL = 0,
+        XCL_FW_USER_CONTROL,
+        XCL_FW_DATAPATH,
+        XCL_FW_MAX_LEVEL // always the last one
+};
+
+/**
+ * struct xclAXIErrorStatus - Record used to capture specific error
+ *
+ * @mErrFirewallTime:    Timestamp of when Firewall tripped
+ * @mErrFirewallStatus:  Error code obtained from the Firewall
+ * @mErrFirewallID:      Firewall ID
+ */
+struct xclAXIErrorStatus {
+        unsigned long       mErrFirewallTime;
+        unsigned            mErrFirewallStatus;
+        enum xclFirewallID  mErrFirewallID;
+};
+
+struct xclPCIErrorStatus {
+        unsigned mDeviceStatus;
+        unsigned mUncorrErrStatus;
+        unsigned mCorrErrStatus;
+        unsigned rsvd1;
+        unsigned rsvd2;
+};
+
+/**
+ * struct xclErrorStatus - Container for all error records
+ *
+ * @mNumFirewalls:    Count of Firewalls in the record (max is 8)
+ * @mAXIErrorStatus:  Records holding Firewall information
+ * @mPCIErrorStatus:  Unused
+ */
+struct xclErrorStatus {
+        unsigned  mNumFirewalls;
+        struct xclAXIErrorStatus mAXIErrorStatus[8];
+        struct xclPCIErrorStatus mPCIErrorStatus;
+        unsigned mFirewallLevel;
+};
+
+#endif /* XCLERR_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xclfeatures.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xclfeatures.h
@@ -0,0 +1,146 @@
+/**
+ *  Copyright (C) 2015-2018, Xilinx Inc
+ *
+ *  This file is dual licensed.	 It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+
+/**
+ *  Xilinx SDAccel FPGA BIOS definition
+ *  Copyright (C) 2016-2018, Xilinx Inc - All rights reserved
+ */
+
+#ifndef xclfeatures_h_
+#define xclfeatures_h_
+
+#define FEATURE_ROM_MAJOR_VERSION 10
+#define FEATURE_ROM_MINOR_VERSION 1
+
+//Layout: At address 0xB0000, we will have the FeatureRomHeader that comprises:
+//
+//1. First have FeatureRomHeader: 152 bytes of information followed by
+//2. Then, as a part of FeatureRomHeader we have the PRRegion struct(s).
+//	The number of such structs will be same as OCLRegionCount.
+//3. After this the freq scaling table is laid out.
+//
+
+//#include <stdint.h>
+
+struct PartialRegion {
+	uint16_t clk[4];
+	int8_t XPR; //0 : non-xpt, 1: xpr
+};
+
+// Each entry represents one row in freq scaling table.
+struct FreqScalingTableRow {
+	short config0;
+	short freq;
+	short config2;
+};
+
+enum PROMType  {
+	BPI	= 0
+	, SPI	= 1
+   //room for 6 more types of flash devices.
+};
+
+enum DebugType	{
+	DT_NIFD	 = 0x01,
+	DT_FIREWALL  = 0x02
+  //There is room for future expansion upto 8 IPs
+};
+
+// This bit mask is used with the FeatureBitMap to calculate 64 bool features
+//
+// To test if a feature is provided:
+//   FeatureRomHeader header;
+//   if (FeatureBitMask::FBM_IS_UNIFIED & header.FeatureBitMap)
+//     // it is supported
+//   else
+//     // it is not supported
+//
+// To set if a feature is provided:
+//   header.FeatureBitMap = 0;
+//   header.FeatureBitMap |= FeatureBitMask::FBM_IS_UNIFIED;
+//
+enum FeatureBitMask {
+	UNIFIED_PLATFORM       =   0x0000000000000001	     /* bit 1 : Unified platform */
+	, XARE_ENBLD	       =   0x0000000000000002	    /* bit 2 : Aurora link enabled DSA */
+	, BOARD_MGMT_ENBLD     =   0x0000000000000004	    /* bit 3 : Has MB based power monitoring */
+	, MB_SCHEDULER	       =   0x0000000000000008	    /* bit 4:  Has MB based scheduler */
+	, PROM_MASK	       =   0x0000000000000070	    /* bits 5,6 &7  : 3 bits for PROMType */
+	/**  ------ Bit 8 unused **/
+	, DEBUG_MASK	       =   0x000000000000FF00	    /* bits 9 through 16  : 8 bits for DebugType */
+	, PEER_TO_PEER	       =   0x0000000000010000	    /* bits 17	: Bar 2 is a peer to peer bar*/
+	, FBM_UUID		       =   0x0000000000020000	    /* bits 18	: UUID enabled. uuid[16] field is valid*/
+	, HBM		       =   0x0000000000040000	    /* bits 19	: Device has HBM's. HBMCount/Size are valid*/
+	, CDMA		       =   0x0000000000080000	    /* bits 21	: Device has CDMA*/
+	, QDMA		       =   0x0000000000100000	    /* bits 20	: Device has QDMA*/
+	, RUNTIME_CLK_SCALE    =   0x0000000000200000	    /* bit 22 : Device has RUNTIME CLOCK SCALING feature*/
+	, PASSTHROUGH_VIRTUALIZATION    =   0x0000000000400000	/* bit 23 : Device has Passthrough Virtualization feature*/
+
+   //....more
+};
+
+
+
+// In the following data structures, the EntryPointString, MajorVersion, and MinorVersion
+// values are all used in the Runtime to identify if the ROM is producing valid data, and
+// to pick the schema to read the rest of the data; Ergo, these values shall not change.
+
+/*
+ * Struct used for >  2017.2_sdx
+ * This struct should be used for version (==) 10.0 (Major: 10, Minor: 0)
+ */
+struct FeatureRomHeader {
+	unsigned char EntryPointString[4];  // This is "xlnx"
+	uint8_t MajorVersion;		    // Feature ROM's major version eg 1
+	uint8_t MinorVersion;		    // minor version eg 2.
+	// -- DO NOT CHANGE THE TYPES ABOVE THIS LINE --
+	uint32_t VivadoBuildID;		    // Vivado Software Build (e.g., 1761098 ). From ./vivado --version
+	uint32_t IPBuildID;		    // IP Build (e.g., 1759159 from abve)
+	uint64_t TimeSinceEpoch;	    // linux time(NULL) call, at write_dsa_rom invocation
+	unsigned char FPGAPartName[64];	    // The hardware FPGA part. Null termninated
+	unsigned char VBNVName[64];	    // eg : xilinx:xil-accel-rd-ku115:4ddr-xpr:3.4: null terminated
+	uint8_t DDRChannelCount;	    // 4 for TUL
+	uint8_t DDRChannelSize;		    // 4 (in GB)
+	uint64_t DRBaseAddress;		    // The Dynamic Range's (AppPF/CL/Userspace) Base Address
+	uint64_t FeatureBitMap;		    // Feature Bit Map, 64 different bool features, maps to enum FeatureBitMask
+	unsigned char uuid[16];		    // UUID of the DSA.
+	uint8_t HBMCount;		    // Number of HBMs
+	uint8_t HBMSize;		    // Size of (each) HBM in GB
+	uint32_t CDMABaseAddress[4];	    // CDMA base addresses
+};
+
+#endif // xclfeatures_h_
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xclhal2_mem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xclhal2_mem.h
@@ -0,0 +1,23 @@
+/*
+ * Copyright (C) 2019, Xilinx Inc - All rights reserved.
+ * Xilinx Runtime (XRT) APIs
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"). You may
+ * not use this file except in compliance with the License. A copy of the
+ * License is located at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ */
+
+#ifndef _XCLHAL2_MEM_H_
+#define _XCLHAL2_MEM_H_
+
+#include "xrt_mem.h"
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xgq_cmd_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xgq_cmd_common.h
@@ -0,0 +1,336 @@
+/*
+ *  Copyright (C) 2021-2022, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef XGQ_CMD_COMMON_H
+#define XGQ_CMD_COMMON_H
+
+/* !!! This header file is for internal project use only and it is subject to removal without notice !!! */
+#if defined(__KERNEL__)
+# include <linux/types.h>
+#else
+# include <stdint.h>
+# include <stddef.h>
+# include <errno.h>
+#endif
+
+/**
+ * This header file could be used both in driver and user space applications.
+ * It could be used cross platform as well. Need assert macro.
+ */
+#ifdef __cplusplus
+  // Used C++ static assert
+  #define XGQ_STATIC_ASSERT(e,m) \
+    static_assert (e, m)
+#else
+  // Use our "custom" kernel compilation assert
+  #define XGQ_ASSERT_CONCAT_(a, b) a##b
+  #define XGQ_ASSERT_CONCAT(a, b) XGQ_ASSERT_CONCAT_(a, b)
+
+  // Create an artifitial assertion via a bad divide by zero assertion.
+  #define XGQ_STATIC_ASSERT(e,m) \
+    enum { XGQ_ASSERT_CONCAT(xgq_assert_line_, __LINE__) = 1/(int)(!!(e)) }
+#endif
+
+#define XGQ_SUB_Q1_SLOT_SIZE	512	// NOLINT
+#define XGQ_QUEUE1_SLOT_NUM	4	// NOLINT
+#define XGQ_QUEUE1_SLOT_MASK	(XGQ_QUEUE1_SLOT_NUM - 1)	// NOLINT
+
+#define XGQ_Q1_SUB_SIZE		(XGQ_SUB_Q1_SLOT_SIZE * XGQ_QUEUE1_SLOT_NUM) // NOLINT
+#define XGQ_Q1_COM_SIZE		(XGQ_COM_Q1_SLOT_SIZE * XGQ_QUEUE1_SLOT_NUM) // NOLINT
+
+/* Opcode encoding rules:
+ * | 15 ------ 11 | 10 ----- 8 | 7 ----- 0 |
+ * +--------------+------------+-----------+
+ * |   Reserved   |    Type    |  OP's ID  |
+ * +--------------+------------+-----------+
+ */
+enum xgq_cmd_opcode {
+	/* Management command type */
+	XGQ_CMD_OP_LOAD_XCLBIN		= 0x0,
+	XGQ_CMD_OP_CONFIGURE		= 0x1,
+
+	XGQ_CMD_OP_GET_LOG_PAGE		= 0x8,
+
+	XGQ_CMD_OP_DOWNLOAD_PDI		= 0xa,
+	XGQ_CMD_OP_CLOCK		= 0xb,
+	XGQ_CMD_OP_SENSOR		= 0xc,
+	XGQ_CMD_OP_LOAD_APUBIN		= 0xd,
+	XGQ_CMD_OP_VMR_CONTROL		= 0xe,
+
+	/* User command type */
+	XGQ_CMD_OP_START_CUIDX	        = 0x100,
+	XGQ_CMD_OP_START_CUIDX_INDIR	= 0x101,
+	XGQ_CMD_OP_START_CUIDX_KV	= 0x102,
+	XGQ_CMD_OP_START_CUIDX_KV_INDIR	= 0x103,
+	XGQ_CMD_OP_INIT_CUIDX	        = 0x104,
+	XGQ_CMD_OP_INIT_CUIDX_INDIR     = 0x105,
+	XGQ_CMD_OP_INIT_CUIDX_KV	= 0x106,
+	XGQ_CMD_OP_INIT_CUIDX_KV_INDIR	= 0x107,
+	XGQ_CMD_OP_CFG_START	        = 0x108,
+	XGQ_CMD_OP_CFG_END	        = 0x109,
+	XGQ_CMD_OP_CFG_CU	        = 0x10a,
+	XGQ_CMD_OP_QUERY_CU	        = 0x10b,
+	XGQ_CMD_OP_CLOCK_CALIB     	= 0x10c,
+	XGQ_CMD_OP_ACCESS_VALID     	= 0x10d,
+	XGQ_CMD_OP_DATA_INTEGRITY   	= 0x10e,
+	XGQ_CMD_OP_EXIT             	= 0x10f,
+
+	/* Common command type */
+	XGQ_CMD_OP_BARRIER		= 0x200,
+	XGQ_CMD_OP_EXIT_ERT		= 0x201,
+	XGQ_CMD_OP_IDENTIFY		= 0x202,
+};
+
+enum xgq_cmd_addr_type {
+	XGQ_CMD_ADD_TYPE_DEVICE		= 0x0,
+	XGQ_CMD_ADD_TYPE_SLAVEBRIDGE	= 0x1,
+	XGQ_CMD_ADD_TYPE_HOST_MEM	= 0x2,
+	XGQ_CMD_ADD_TYPE_AP_OFFSET	= 0x3,
+};
+
+#define XGQ_SQ_CMD_NEW 1
+
+enum xgq_cmd_state {
+	XGQ_CMD_STATE_COMPLETED		= 0x0,
+	XGQ_CMD_STATE_ABORTED		= 0x1,
+	XGQ_CMD_STATE_TIMEOUT		= 0x2,
+	XGQ_CMD_STATE_INVALID		= 0x3,
+	XGQ_CMD_STATE_CONFLICT_ID	= 0x4,
+};
+
+enum xgq_cmd_page_id {
+	XGQ_CMD_PAGE_ID_HEALTH		= 0x0,
+	XGQ_CMD_PAGE_ID_ERROR_INFO	= 0x1,
+	XGQ_CMD_PAGE_ID_PROFIL		= 0x2,
+	XGQ_CMD_PAGE_ID_DEBUG		= 0x3,
+	XGQ_CMD_PAGE_ID_SENSOR		= 0x4,
+};
+
+/*
+ * On some platforms, XGQ IP and XGQ ring buffer can be located
+ * on different hardware location, e.g. separate PCIe BARs. So
+ * updating doorbell register can be faster than the ring buffer.
+ * We have a special flag in Submission queue and Completion queue
+ * entry to indicate this entry is a new one. This flag is located
+ * at the first Word MSB in both Submission queue and Completion
+ * entry. After receiving doorbell update interrupt, consumer will
+ * need to check this flag as well to make sure this is a new entry.
+ * After the check, consumer also needs to clear it so that it won't
+ * be confused by the stale data next time when it comes to this slot.
+ * To handle this case, XGQ_OUT_OF_ORDER_WRITE macro shall be defined.
+ *
+ * Note: for same reason, the producer will make sure to write to
+ *       Word0 as the last update of the Submission and Completion
+ *       queue entry before writing to the doorbell register.
+ */
+#define XGQ_ENTRY_NEW_FLAG_MASK		0x80000000
+
+/**
+ * struct xgq_cmd_sq_hdr: XGQ submission queue entry header format
+ *
+ * @opcode:	[15-0]	command opcode identifying specific command
+ * @count:	[30-16]	number of bytes representing packet payload
+ * @state:	[31]	flag indicates this is a new entry
+ * @cid:		unique command id
+ * @rsvd:	        reserved for future use
+ * @cu_domain:	[3-0]	CU domain for certain start CU op codes
+ * @cu_idx:	[11-0]	CU index for certain start CU op codes
+ *
+ * Any command in XGQ submission queue shares same command header.
+ * An command ID is used to identify the command. When the command
+ * is completed, the same command ID is put into the completion
+ * queue entry.
+ *
+ * Please declare this struct at the begin of a submission queue entry
+ */
+struct xgq_cmd_sq_hdr {
+	union {
+		struct {
+			uint32_t opcode:16; /* [15-0]   */
+			uint32_t count:15;  /* [30-16] */
+			uint32_t state:1;   /* [31] */
+			uint16_t cid;
+			union {
+				uint16_t rsvd;
+				struct {
+					uint16_t cu_idx:12;
+					uint16_t cu_domain:4;
+				};
+			};
+		};
+		uint32_t header[2]; // NOLINT
+	};
+};
+XGQ_STATIC_ASSERT(sizeof(struct xgq_cmd_sq_hdr) == 8, "xgq_cmd_sq_hdr structure no longer is 8 bytes in size");
+
+/**
+ * struct xgq_cmd_cq_hdr: XGQ completion queue entry header format
+ *
+ * @cid:        unique command id
+ * @cstate:     command state
+ * @specific:	flag indicates there is command specific info in result
+ * @state:      flag indicates this is a new entry
+ *
+ * This is the header of the completion queue entry. A generic command
+ * state is put into cstate. The command is identified by cid which
+ * matches the cid in submission queue.
+ *
+ * Please declare this struct at the begin of a completion queue entry
+ */
+struct xgq_cmd_cq_hdr {
+	union {
+		struct {
+			uint16_t cid;
+			uint16_t cstate:14;
+			uint16_t specific:1;
+			uint16_t state:1;
+		};
+		uint32_t header[1]; // NOLINT
+	};
+};
+XGQ_STATIC_ASSERT(sizeof(struct xgq_cmd_cq_hdr) == 4, "xgq_cmd_cq_hdr structure no longer is 4 bytes in size");
+
+/**
+ * struct xgq_sub_queue_entry: XGQ submission queue entry
+ *
+ * @hdr: header of the entry
+ * @data: payload of the entry
+ *
+ * XGQ submission command is variable length command.
+ * This is very useful when a XGQ entity needs to access command payload,
+ * but it doesn't need to know the detail of the payload. 
+ */
+struct xgq_sub_queue_entry {
+	struct xgq_cmd_sq_hdr  hdr;
+	uint32_t data[1]; // NOLINT
+};
+
+/**
+ * struct xgq_com_queue_entry: XGQ completion queue entry format
+ *
+ * @hdr: header of the entry
+ * @result: command specific result
+ * @resvd: reserved
+ * @rcode: POSIX error return code
+ *
+ * When a command is completed, a completion entry is put into completion
+ * queue. A generic command state is put into cstate. The command is
+ * identified by cid which matches the cid in submission queue.
+ * More command specific result is put into result field. POSIX error code
+ * can be put into rcode. This is useful for some case like PS kernel.
+ *
+ * All completion queue entries have a same fixed size of 4 words.
+ */
+struct xgq_com_queue_entry {
+	union {
+		struct {
+			struct xgq_cmd_cq_hdr hdr;
+			uint32_t result;
+			uint32_t resvd;
+			uint32_t rcode;
+		};
+		uint32_t data[4]; // NOLINT
+	};
+};
+XGQ_STATIC_ASSERT(sizeof(struct xgq_com_queue_entry) == 16, "xgq_com_queue_entry structure no longer is 16 bytes in size");
+
+#define XGQ_SUB_HEADER_SIZE	(sizeof(struct xgq_cmd_sq_hdr)) // NOLINT
+#define XGQ_COM_Q1_SLOT_SIZE	(sizeof(struct xgq_com_queue_entry)) // NOLINT
+
+/**
+ * struct xgq_cmd_load_xclbin: load XCLBIN command
+ *
+ * @hdr: header of the command
+ * @address:	XCLBIN address
+ * @size:	XCLBIN size in Byte
+ * @addr_type:	Address type
+ *
+ * This command is used to load XCLBIN to device through XGQ.
+ * This is an indirect command that XCLBIN blob's address is
+ * embedded.
+ */
+struct xgq_cmd_load_xclbin {
+	struct xgq_cmd_sq_hdr  hdr;
+	uint64_t address;
+	uint32_t size;
+	uint32_t addr_type:4;
+	uint32_t rsvd1:28;
+};
+
+struct xgq_cmd_configure {
+	struct xgq_cmd_sq_hdr  hdr;
+	uint32_t data[1]; // NOLINT
+};
+
+/**
+ * struct xgq_cmd_indentify: identify command
+ *
+ * @hdr: header of the command
+ *
+ * This command is used to get XGQ command set version.
+ * After that XGQ client XGQ server can support
+ */
+struct xgq_cmd_identify {
+	struct xgq_cmd_sq_hdr  hdr;
+};
+
+/**
+ * struct xgq_cmd_resp_indentify: identify command response
+ *
+ * @minor: minor version of the XGQ command set
+ * @major: major version of the XGQ command set
+ *
+ * This command is used to get XGQ command set version information.
+ */
+struct xgq_cmd_resp_identify {
+	struct xgq_cmd_cq_hdr  hdr;
+	union {
+		struct {
+			uint16_t minor;
+			uint16_t major;
+		};
+		uint32_t result;
+	};
+	uint32_t resvd;
+	uint32_t rcode;
+};
+
+struct xgq_cmd_exit_ert {
+	struct xgq_cmd_sq_hdr  hdr;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xgq_cmd_ert.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xgq_cmd_ert.h
@@ -0,0 +1,386 @@
+/*
+ *  Copyright (C) 2021-2022, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef XGQ_CMD_ERT_H
+#define XGQ_CMD_ERT_H
+
+/* !!! This header file is for internal project use only and it is subject to removal without notice !!! */
+#include "xgq_cmd_common.h"
+
+/* This header file defines data structure format for user opcodes. */
+
+/**
+ * struct xgq_cmd_start_cuidx: start CU by index command
+ *
+ * @hdr:	CU command header
+ * @data:	CU parameters
+ *
+ * This command is used to start a specific CU with its index. And the
+ * CU parameters are embedded in the command payload.
+ */
+struct xgq_cmd_start_cuidx {
+	struct xgq_cmd_sq_hdr hdr;
+	uint32_t data[1]; // NOLINT
+};
+
+/**
+ * struct xgq_cmd_start_cuidx_kv: start CU with offset-value pairs by index command
+ *
+ * @hdr:	CU command header
+ * @data:	cu parameters in a [offset:value] list. The offset is in bytes.
+ *
+ * This command is used to start a specific CU with its index. And the
+ * [offset:value] list are embedded in the command payload.
+ */
+struct xgq_cmd_start_cuidx_kv {
+	struct xgq_cmd_sq_hdr hdr;
+	/*
+	 * even index (0, 2, 4, ...) are offsets
+	 * odd index (1, 3, 5, ...) are values
+	 */
+	uint32_t data[1]; // NOLINT
+};
+
+/**
+ * struct xgq_cmd_init_cuidx: init CU by index command
+ *
+ * @hdr:	CU command header
+ * @offset:	Offset to start initialize CU parameters
+ * @data:	CU parameters
+ *
+ * This command is used to initial a specific CU with its index. And the
+ * CU parameters are embedded in the command payload.
+ *
+ * This command would NOT kick off the CU.
+ */
+struct xgq_cmd_init_cuidx {
+	struct xgq_cmd_sq_hdr hdr;
+	uint32_t offset;
+	uint32_t data[1]; // NOLINT
+};
+
+/**
+ * struct xgq_cmd_init_cuidx_kv: init CU with offset-value pairs by index command
+ *
+ * @hdr:	CU command header
+ * @data:	CU parameters in a [offset:value] list. The offset is in bytes.
+ *
+ * This command is used to initial a specific CU with its index. And the
+ * [offset:value] list are embedded in the command payload.
+ *
+ * This command would NOT kick off the CU.
+ */
+struct xgq_cmd_init_cuidx_kv {
+	struct xgq_cmd_sq_hdr hdr;
+	/*
+	 * even index (0, 2, 4, ...) are offsets
+	 * odd index (1, 3, 5, ...) are values
+	 */
+	uint32_t data[1]; // NOLINT
+};
+
+/**
+ * struct xgq_cmd_config_start: configure start command
+ *
+ * @num_cus: number of CUs
+ * @i2h: ERT interrupt to host enable
+ * @i2e: Host interrupt to ERT enable
+ * @cui: CU interrupt to ERT enable
+ *
+ * This command would let ERT goes into configure state
+ */
+struct xgq_cmd_config_start {
+	struct xgq_cmd_sq_hdr hdr;
+
+	/* word 2 */
+	uint32_t num_cus:13;
+	uint32_t i2h:1;
+	uint32_t i2e:1;
+	uint32_t cui:1;
+	uint32_t mode:2;
+	uint32_t echo:1;
+	uint32_t verbose:1;
+	uint32_t resvd:12;
+
+	/* word 3 */
+	uint32_t num_scus:32;
+};
+
+/**
+ * struct xgq_cmd_clock_calib: xgq clock counter command
+ *
+ * This command would let ERT read the clock counter
+ */
+
+struct xgq_cmd_clock_calib {
+	struct xgq_cmd_sq_hdr hdr;
+};
+
+/**
+ * struct xgq_cmd_access_valid: ERT performance measurement
+ *
+ * This command would measure the performance number of ERT accessing peripherals
+ */
+
+struct xgq_cmd_access_valid {
+	struct xgq_cmd_sq_hdr hdr;
+};
+
+/**
+ * struct xgq_cmd_data_integrity: queue data integrity test
+ *
+ * @rw_count: the number of write operation remaining
+ * @draft:    the offset of read/write operation
+ *
+ * This command would let ERT test host/device accessibility
+ */
+
+struct xgq_cmd_data_integrity {
+	struct xgq_cmd_sq_hdr hdr;
+
+	uint32_t rw_count;
+	uint32_t draft;
+};
+/**
+ * struct xgq_cmd_resp_config_start: configure start command response
+ *
+ * @i2h: ERT interrupt to host enabled
+ * @i2e: Host interrupt to ERT enable
+ * @cui: CU interrupt to ERT enable
+ * @ob:  device supports out of band memory
+ *
+ * The response of start configure command.
+ */
+struct xgq_cmd_resp_config_start {
+	struct xgq_cmd_cq_hdr hdr;
+
+	uint32_t i2h:1;
+	uint32_t i2e:1;
+	uint32_t cui:1;
+	uint32_t ob:1;
+	uint32_t rsvd:28;
+	uint32_t resvd;
+	uint32_t rcode;
+};
+
+/**
+ * struct xgq_cmd_config_end: configure end command
+ *
+ * This command has no payload. Once ERT received this command it knowns configure is done.
+ */
+struct xgq_cmd_config_end {
+	struct xgq_cmd_sq_hdr hdr;
+};
+
+/**
+ * struct xgq_cmd_config_cu: configure CU command
+ *
+ * @cu_idx: cu index to configure
+ * @ip_ctrl: IP control protocol
+ * @map_size: use this size to map CU if apply
+ * @laddr: lower 32 bits of the CU address
+ * @haddr: higher 32 bits of the CU address
+ * @payload_size: CU XGQ slot payload size
+ * @name: name of the CU
+ * @uuid: UUID of the XCLBIN of the CU
+ *
+ * Configure PL/PS CUs.
+ */
+struct xgq_cmd_config_cu {
+	struct xgq_cmd_sq_hdr hdr;
+
+	/* word 2 */
+	uint32_t cu_idx:12;
+	uint32_t cu_domain:4;
+	uint32_t ip_ctrl:8;
+	uint32_t rsvd2:8;
+
+	uint32_t map_size;
+	uint32_t laddr;
+	uint32_t haddr;
+	uint32_t payload_size;
+	char name[64];
+	unsigned char uuid[16];
+};
+
+/**
+ * struct xgq_cmd_query_cu: query CU command
+ *
+ * @cu_idx: cu index to query
+ * @type: type of the query
+ *
+ */
+enum xgq_cmd_query_cu_type {
+	XGQ_CMD_QUERY_CU_CONFIG =	0x0,
+	XGQ_CMD_QUERY_CU_STATUS =	0x1,
+};
+
+struct xgq_cmd_query_cu {
+	struct xgq_cmd_sq_hdr hdr;
+
+	/* word 2 */
+	uint32_t cu_idx:12;
+	uint32_t cu_domain:4;
+	uint32_t type:4;
+	uint32_t rsvd2:8;
+};
+
+/**
+ * struct xgq_cmd_resp_query_cu: query CU command response
+ *
+ * @status: status of the CU
+ *
+ * @xgq_id: XGQ ID
+ * @type: type of the queue
+ * @offset: ring buffer offset
+ *
+ */
+enum xgq_cmd_resp_query_cu_type {
+	XGQ_CMD_RESP_QUERY_XGQ =	0x0,
+	XGQ_CMD_RESP_QUERY_OOO =	0x1,
+};
+
+struct xgq_cmd_resp_query_cu {
+	struct xgq_cmd_cq_hdr hdr;
+
+	union {
+		struct {
+			uint16_t status;
+			uint16_t rsvd1;
+			uint32_t resvd;
+		};
+		struct {
+			uint32_t xgq_id:12;
+			uint32_t rsvd2:4;
+			uint32_t size:15;
+			uint32_t type:1;
+			uint32_t offset;
+		};
+	};
+	uint32_t rcode;
+};
+
+/**
+ * struct xgq_cmd_resp_clock_calib: query clock counter response
+ *
+ * @timestamp: the number of clock counter
+ *
+ */
+
+struct xgq_cmd_resp_clock_calib {
+	struct xgq_cmd_cq_hdr hdr;
+
+	union {
+		struct {
+			uint32_t resvd;
+			uint32_t timestamp;
+		};
+	};
+	uint32_t rcode;
+};
+
+/**
+ * struct xgq_cmd_resp_access_valid: query performance measurement response
+ *
+ * @cq_read_single: the cycle number of single queue read
+ * @cq_write_single: the cycle number of single queue write
+ * @cu_read_single: the cycle number of single CU read
+ * @cu_write_single: the cycle number of single CU write
+ *
+ */
+
+struct xgq_cmd_resp_access_valid {
+	struct xgq_cmd_cq_hdr hdr;
+
+	union {
+		struct {
+			uint16_t status;
+			uint16_t rsvd1;
+			uint32_t resvd;
+		};
+		struct {
+			uint8_t cq_read_single;
+			uint8_t cq_write_single;
+			uint8_t cu_read_single;
+			uint8_t cu_write_single;
+		};
+	};
+	uint32_t rcode;
+};
+
+/**
+ * struct xgq_cmd_resp_data_integrity: device accessibility response
+ *
+ * @h2d_access:     the result of host to device accessibility
+ * @d2d_access:     the result of device accessibility
+ * @d2cu_access:    the result of device to cu accessibility
+ * @data_integrity: the result of stress test
+ *
+ */
+
+struct xgq_cmd_resp_data_integrity {
+	struct xgq_cmd_cq_hdr hdr;
+
+	union {
+		struct {
+			uint32_t h2d_access:1;
+			uint32_t d2d_access:1;
+			uint32_t d2cu_access:1;
+			uint32_t data_integrity:1;
+			uint32_t resvd:28;
+		};
+	};
+	uint32_t rcode;
+};
+
+/* Helper functions */
+static inline uint32_t xgq_cmd_get_cu_payload_size(struct xgq_cmd_sq_hdr *hdr)
+{
+	uint32_t ret = hdr->count;
+
+	if (hdr->opcode == XGQ_CMD_OP_INIT_CUIDX)
+		ret -= sizeof(uint32_t);
+	return ret;
+}
+
+static inline uint32_t xgq_cmd_is_cu_kv(struct xgq_cmd_sq_hdr *hdr)
+{
+	return (hdr->opcode == XGQ_CMD_OP_START_CUIDX_KV ||
+		hdr->opcode == XGQ_CMD_OP_START_CUIDX_KV) ? 1 : 0;
+}
+
+#endif // XGQ_CMD_ERT_H
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xgq_cmd_vmr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xgq_cmd_vmr.h
@@ -0,0 +1,372 @@
+/*
+ *  Copyright (C) 2021-2022, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef XGQ_CMD_VMR_H
+#define XGQ_CMD_VMR_H
+
+/* !!! This header file is for internal project use only and it is subject to removal without notice !!! */
+#include "xgq_cmd_common.h"
+
+/* This header file defines struct of mgmt command type opcode */
+
+/* The Clock IP use index 0 for data, 1 for kernel, 2 for sys, 3 for sys1 */ 
+#define XGQ_CLOCK_WIZ_MAX_RES           4
+
+/**
+ * sensor data request types
+ */
+enum xgq_cmd_sensor_application_id {
+	XGQ_CMD_SENSOR_AID_GET_SIZE			= 0x1,
+	XGQ_CMD_SENSOR_AID_GET_SDR			= 0x2,
+	XGQ_CMD_SENSOR_AID_GET_SINGLE_SENSOR_DATA	= 0x3,
+	XGQ_CMD_SENSOR_AID_GET_ALL_SENSOR_DATA		= 0x4,
+};
+
+/**
+ * sensor data request types
+ */
+enum xgq_cmd_sensor_page_id {
+	XGQ_CMD_SENSOR_SID_GET_SIZE	= 0x0,
+	XGQ_CMD_SENSOR_SID_BDINFO	= 0x1,
+	XGQ_CMD_SENSOR_SID_TEMP		= 0x2,
+	XGQ_CMD_SENSOR_SID_VOLTAGE	= 0x3,
+	XGQ_CMD_SENSOR_SID_CURRENT	= 0x4,
+	XGQ_CMD_SENSOR_SID_POWER	= 0x5,
+	XGQ_CMD_SENSOR_SID_QSFP		= 0x6,
+	XGQ_CMD_SENSOR_SID_ALL		= 0x7,
+};
+
+/**
+ * clock operation request types
+ */
+enum xgq_cmd_clock_req_type {
+	XGQ_CMD_CLOCK_WIZARD 		= 0x0,
+	XGQ_CMD_CLOCK_COUNTER		= 0x1,
+	XGQ_CMD_CLOCK_SCALE		= 0x2,
+};
+
+/**
+ * multi-boot operation request types
+ */
+enum xgq_cmd_vmr_control_type {
+	XGQ_CMD_VMR_QUERY	= 0x0,
+	XGQ_CMD_BOOT_DEFAULT	= 0x1,
+	XGQ_CMD_BOOT_BACKUP	= 0x2,
+	XGQ_CMD_PROGRAM_SC	= 0x3,
+	XGQ_CMD_VMR_DEBUG	= 0x4,
+};
+
+/**
+ * log page type
+ */
+enum xgq_cmd_log_page_type {
+	XGQ_CMD_LOG_AF_CHECK	= 0x0,
+	XGQ_CMD_LOG_FW		= 0x1,
+	XGQ_CMD_LOG_INFO	= 0x2,
+	XGQ_CMD_LOG_AF_CLEAR	= 0x3,
+	XGQ_CMD_LOG_ENDPOINT	= 0x4,
+};
+
+/**
+ * struct xgq_cmd_log_payload: log_page request command
+ *
+ * @address:	pre-allocated log data, device writes log data at this address
+ * @size:	size of pre-allocated log data
+ * @offset:	offset of returned device data
+ * @pid:	log_page page id
+ * @addr_type:	pre-allocated address type
+ *
+ * This payload is used for log_page and sensor data report.
+ */
+struct xgq_cmd_log_payload {
+	uint64_t address;
+	uint32_t size;
+	uint32_t offset;
+	uint32_t pid:16;
+	uint32_t addr_type:3;
+	uint32_t rsvd1:13;
+	uint32_t pad;
+};
+
+/**
+ * struct xgq_cmd_sensor_payload: sensor_page request command
+ *
+ * @address:	pre-allocated sensor data, device writes sensor data at this address
+ * @size:	size of pre-allocated sensor data
+ * @offset:	offset of returned device data
+ * @pid:	sensor request id
+ * @addr_type:	pre-allocated address type
+ *
+ * This payload is used for sensor data report.
+ */
+struct xgq_cmd_sensor_payload {
+	uint64_t address;
+	uint32_t size;
+	uint32_t offset;
+	uint32_t aid:8;
+	uint32_t sid:8;
+	uint32_t addr_type:3;
+	uint32_t rsvd1:13;
+	uint32_t pad;
+};
+
+/**
+ * struct xgq_cmd_clock_payload: clock request command
+ *
+ * @ocl_region:		clock region
+ * @ocl_req_type:	clock request type
+ * @ocl_req_id:		clock resource index 0,1,2,3
+ * @ocl_req_num:	max effective index 1 -> 4
+ * @ocl_req_freq:	request freq number array
+ */
+struct xgq_cmd_clock_payload {
+	uint32_t ocl_region;
+	uint32_t ocl_req_type:8;
+	uint32_t ocl_req_id:2;
+	uint32_t ocl_req_num:4;
+	uint32_t rsvd1:18;
+	uint32_t ocl_req_freq[XGQ_CLOCK_WIZ_MAX_RES];
+};
+
+/**
+ * struct xgq_cmd_data_payload: data request payload command
+ *
+ * @address:		data that needs to be transferred
+ * @size:		data size
+ * @addr_type:		address_type
+ */
+struct xgq_cmd_data_payload {
+	uint64_t address;
+	uint32_t size;
+	uint32_t remain_size;
+	uint32_t addr_type:4;
+	uint32_t flash_type:4;
+	uint32_t rsvd1:24;
+	uint32_t pad1;
+};
+
+enum xgq_cmd_flash_type {
+	XGQ_CMD_FLASH_DEFAULT		= 0x0,
+	XGQ_CMD_FLASH_NO_BACKUP		= 0x1,
+	XGQ_CMD_FLASH_TO_LEGACY		= 0x2,
+};
+
+enum xgq_cmd_debug_type {
+	XGQ_CMD_DBG_CLEAR		= 0x0,
+	XGQ_CMD_DBG_RMGMT		= 0x1,
+	XGQ_CMD_DBG_VMC			= 0x2,
+};
+
+/**
+ * struct xgq_cmd_vmr_control_payload: vmr controlling ops
+ *
+ * @req_type:		request type
+ */
+struct xgq_cmd_vmr_control_payload {
+	uint32_t req_type:8;
+	uint32_t debug_level:3;
+	uint32_t debug_type:5;
+	uint32_t rsvd:16;
+};
+
+/**
+ * struct xgq_cmd_sq: vmr xgq command
+ *
+ * @hdr:		vmr xgq command header
+ *
+ * @log_payload:	corresponding payload definition in a union
+ * @clock_payload:
+ * @pdi_payload:
+ * @xclbin_payload:
+ * @sensor_payload:
+ */
+struct xgq_cmd_sq {
+	struct xgq_cmd_sq_hdr hdr;
+	union {
+		struct xgq_cmd_log_payload		log_payload;
+		struct xgq_cmd_clock_payload		clock_payload;
+		struct xgq_cmd_data_payload		pdi_payload;
+		struct xgq_cmd_data_payload		xclbin_payload;
+		struct xgq_cmd_sensor_payload		sensor_payload;
+		struct xgq_cmd_vmr_control_payload	vmr_control_payload;
+	};
+};
+
+/**
+ * struct xgq_cmd_cq_default_payload: vmr default completion payload
+ *
+ * @result:	result code
+ */
+struct xgq_cmd_cq_default_payload {
+	uint32_t resvd0;
+	uint32_t resvd1;
+};
+
+/**
+ * struct xgq_cmd_cq_clock_payload: vmr clock completion payload 
+ *
+ * @ocl_freq: 	result of clock frequency value
+ */
+struct xgq_cmd_cq_clock_payload {
+	uint32_t ocl_freq;
+	uint32_t resvd;
+};
+
+/**
+ * struct xgq_cmd_cq_sensor_payload: vmr sensor completion payload
+ *
+ * @result: 	result code
+ */
+struct xgq_cmd_cq_sensor_payload {
+	uint32_t result;
+	uint32_t resvd;
+};
+
+/**
+ * struct xgq_cmd_cq_log_page_payload: vmr log page completion payload
+ *
+ * @count:	how many data returned in bytes
+ */
+struct xgq_cmd_cq_log_page_payload {
+	uint32_t count;
+	uint32_t resvd1;
+};
+
+/**
+ * struct xgq_cmd_cq_log_page_payload: load xclbin/pdi data payload
+ *
+ * @count:	how many data returned in bytes
+ */
+struct xgq_cmd_cq_data_payload {
+	uint32_t count;
+	uint32_t resvd1;
+};
+
+/**
+ * struct xgq_cmd_cq_vmr_payload: vmr device status payload
+ *
+ * bitfields for indicting flash partition statistics.
+ * vmr device status.
+ */
+struct xgq_cmd_cq_vmr_payload {
+	uint16_t has_fpt:1;
+	uint16_t has_fpt_recovery:1;
+	uint16_t boot_on_default:1;
+	uint16_t boot_on_backup:1;
+	uint16_t boot_on_recovery:1;
+	uint16_t has_extfpt:1;
+	uint16_t has_ext_xsabin:1;
+	uint16_t has_ext_scfw:1;
+	uint16_t has_ext_sysdtb:1;
+	uint16_t ps_is_ready:1;
+	uint16_t pl_is_ready:1;
+	uint16_t resvd1:5;
+	uint16_t current_multi_boot_offset;
+	uint32_t debug_level:3;
+	uint32_t program_progress:7;
+	uint16_t resvd2:6;
+	uint16_t boot_on_offset;
+};
+
+/*
+ * struct xgq_cmd_cq: vmr completion command
+ *
+ * @hdr:		vmr completion command header
+ *
+ * @default_payload: 	payload definitions in a union
+ * @clock_payload:
+ * @sensor_payload:
+ * @multiboot_payload:
+ */
+struct xgq_cmd_cq {
+	struct xgq_cmd_cq_hdr hdr;
+	union {
+		struct xgq_cmd_cq_default_payload	cq_default_payload;
+		struct xgq_cmd_cq_clock_payload		cq_clock_payload;
+		struct xgq_cmd_cq_sensor_payload	cq_sensor_payload;
+		struct xgq_cmd_cq_vmr_payload		cq_vmr_payload;
+		struct xgq_cmd_cq_log_page_payload	cq_log_payload;
+		struct xgq_cmd_cq_data_payload		cq_xclbin_payload;
+	};
+	uint32_t rcode;
+};
+XGQ_STATIC_ASSERT(sizeof(struct xgq_cmd_cq) == 16, "xgq_cmd_cq has to be 16 bytes in size");
+
+/**
+ * XGQ memory partition table, should be positioned at shared memory offset 0,
+ *     and inited by VMR software on RPU device.
+ *
+ * We use the memory partition table for sharing info between host and RPU.
+ * Including:
+ *
+ * @vmr_magic_no:	the magic no.
+ * @ring_buffer_off:	the offset of xgq ring buffer inited by xgq server
+ * @ring_buffer_len:	the length of xgq ring buffer inited by xgq server
+ * TODO: only support hearbeat now
+ * @vmr_status_off:	the offset of vmr device status
+ * @vmr_status_len:	the length of vmr device status
+ * @log_msg_index:	the current index of ring buffer log
+ * @log_msg_buf_off:	the offset of dbg log 
+ * @log_msg_buf_len:	the length of dbg log
+ * @vmr_data_start:	the offset of data buffer started
+ * @vmr_data_end: 	the offset of data buffer ended
+ */
+struct vmr_shared_mem {
+	uint32_t	vmr_magic_no;
+	uint32_t	ring_buffer_off;
+	uint32_t	ring_buffer_len;
+	uint32_t	vmr_status_off;
+	uint32_t	vmr_status_len;
+	uint32_t	log_msg_index;
+	uint32_t	log_msg_buf_off;
+	uint32_t	log_msg_buf_len;
+	uint32_t	vmr_data_start;
+	uint32_t	vmr_data_end;
+};
+
+#define VMR_MAGIC_NO	0x564D5230 /* VMR0 */
+
+#define VMR_LOG_ENTRY_SIZE (96)
+#define VMR_LOG_MAX_RECS (50)
+
+struct vmr_log {
+	char	log_buf[VMR_LOG_ENTRY_SIZE];
+};
+
+#define LOG_BUF_LEN (sizeof(struct vmr_log) * VMR_LOG_MAX_RECS);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xgq_impl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xgq_impl.h
@@ -0,0 +1,597 @@
+/*
+ *  Copyright (C) 2021, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef XGQ_IMPL_H
+#define XGQ_IMPL_H
+
+/* !!! This header file is for internal project use only and it is subject to removal without notice !!! */
+#if defined(__KERNEL__)
+# include <linux/types.h>
+#else
+# include <stdint.h>
+# include <stddef.h>
+# include <errno.h>
+#endif /* __KERNEL__ */
+
+#include "xgq_cmd_common.h"
+
+/*
+ * Standard bool type's portability is poor across multiple OSes and HW platforms.
+ * Defineing our own true and false values as integer to avoid using bool.
+ */
+#define XGQ_TRUE	1
+#define XGQ_FALSE	0
+
+/*
+ * Generic XGQ implementation.
+ *
+ * Each platform should define its own xgq_XXX_plat.h where the platform
+ * specific operations are implemented. Afterwards, XGQ_IMPL should be
+ * defined and xgq_impl.h should be included there.
+ *
+ * Note: This file (xgq_impl.h) should only be included by xgq_XXX_plat.h.
+ */
+
+#ifndef XGQ_IMPL
+#if !defined(__KERNEL__)
+#define ____cacheline_aligned_in_smp
+#endif
+static inline void xgq_mem_write32(uint64_t hdl, uint64_t addr, uint32_t val) {}
+static inline void xgq_reg_write32(uint64_t hdl, uint64_t addr, uint32_t val) {}
+static inline uint32_t xgq_mem_read32(uint64_t hdl, uint64_t addr)
+{
+	return 0xFFFFFFFF;
+}
+static inline uint32_t xgq_reg_read32(uint64_t hdl, uint64_t addr)
+{
+	return 0xFFFFFFFF;
+}
+#endif
+
+#ifndef likely
+#define likely(x)	__builtin_expect(!!(x), 1) // NOLINT
+#endif
+#ifndef unlikely
+#define unlikely(x)	__builtin_expect(!!(x), 0) // NOLINT
+#endif
+
+/*
+ * xgq_read32() and xgq_write32() is used when the address can be register or in memory.
+ * The producer pointer is one example today.
+ */
+static inline uint32_t xgq_read32(uint64_t io_hdl, uint64_t addr, int is_mem)
+{
+#ifdef XGQ_MEM_REG_ACCESS_DIFFER
+	return is_mem ? xgq_mem_read32(io_hdl, addr) : xgq_reg_read32(io_hdl, addr);
+#else
+	return xgq_reg_read32(io_hdl, addr);
+#endif
+}
+static inline void xgq_write32(uint64_t io_hdl, uint64_t addr, uint32_t val, int is_mem)
+{
+#ifdef XGQ_MEM_REG_ACCESS_DIFFER
+	is_mem ? xgq_mem_write32(io_hdl, addr, val) : xgq_reg_write32(io_hdl, addr, val);
+#else
+	xgq_reg_write32(io_hdl, addr, val);
+#endif
+}
+
+/*
+ * Currently, this is only used as a workaround for the BRAM read/write collision HW
+ * issue on MB ERT, which will cause ERT to read incorrect value from CQ. We only
+ * trust the value until we read twice and got the same value.
+ */
+static inline uint32_t xgq_double_read32(uint64_t io_hdl, uint64_t addr, int is_mem)
+{
+	uint32_t val[2];
+	int i = 0;
+
+	val[1] = xgq_read32(io_hdl, addr, is_mem);
+	val[0] = val[1] - 1;
+	while (val[0] != val[1])
+		val[i++ & 0x1] = xgq_read32(io_hdl, addr, is_mem);
+	return val[0];
+}
+
+/*
+ * One XGQ consists of one submission (SQ) and one completion ring (CQ) buffer shared by one client
+ * and one server. Client send request through SQ to server, which processes it and send back
+ * response through CQ.
+ */
+#define XGQ_ALLOC_MAGIC			0x5847513F	/* XGQ? */
+#define XGQ_MAJOR			1
+#define XGQ_MINOR			0
+#define XGQ_MIN_NUM_SLOTS		2
+#define XGQ_VERSION			((XGQ_MAJOR<<16)+XGQ_MINOR)
+#define GET_XGQ_MAJOR(version)		(version>>16)
+#define GET_XGQ_MINOR(version)		(version&0xFFFF)
+
+/*
+ * Meta data shared b/w client and server of XGQ
+ */
+struct xgq_header {
+	uint32_t xh_magic; /* Always the first member */
+	uint32_t xh_version;
+
+	/* SQ and CQ share the same num of slots. */
+	uint32_t xh_slot_num;
+
+	uint32_t xh_sq_offset;
+	uint32_t xh_sq_slot_size;
+	uint32_t xh_cq_offset;
+	/* CQ slot size and format is tied to XGQ version. */
+
+	/*
+	 * Consumed pointer for both SQ and CQ are here since they don't generate interrupt,
+	 * so no need to be a register.
+	 */
+	uint32_t xh_sq_consumed;
+	uint32_t xh_cq_consumed;
+
+	uint32_t xh_flags;
+
+	/*
+	 * On some platforms, there is no dedicated producer pointer register. We can use
+	 * below in-mem version to communicate b/w the peers.
+	 */
+	uint32_t xh_sq_produced;
+	uint32_t xh_cq_produced;
+};
+
+/* Software representation of a single ring buffer. */
+struct xgq_ring {
+	struct xgq *xr_xgq; /* pointing back to parent q */
+	uint32_t xr_slot_num;
+	uint32_t xr_slot_sz;
+	uint32_t xr_produced;
+	uint32_t xr_consumed;
+
+	uint64_t xr_produced_addr;
+	uint64_t xr_consumed_addr;
+	uint64_t xr_slot_addr;
+};
+
+/* Software representation of a single XGQ. */
+#define XGQ_DOUBLE_READ		(1UL << 1) // NOLINT
+#define XGQ_IN_MEM_PROD		(1UL << 2) // NOLINT
+struct xgq {
+	uint64_t xq_io_hdl;
+	uint64_t xq_header_addr;
+	uint32_t xq_flags;
+	struct xgq_ring xq_sq ____cacheline_aligned_in_smp;
+	struct xgq_ring xq_cq ____cacheline_aligned_in_smp;
+};
+#define XGQ_NEED_DOUBLE_READ(xgq)	(((xgq)->xq_flags & XGQ_DOUBLE_READ) != 0)
+#define XGQ_IS_IN_MEM_PROD(xgq)		(((xgq)->xq_flags & XGQ_IN_MEM_PROD) != 0)
+
+
+/*
+ * XGQ implementation details and helper routines.
+ */
+
+static inline size_t xgq_ring_len(size_t nslots, size_t slotsz)
+{
+	return sizeof(struct xgq_header) + nslots * (slotsz + sizeof(struct xgq_com_queue_entry));
+}
+
+static inline void xgq_copy_to_ring(uint64_t io_hdl, void *buf, uint64_t tgt, size_t len)
+{
+	size_t i = 0;
+	uint32_t *src = (uint32_t *)buf;
+
+	for (i = 0; i < len / 4; i++, tgt += 4)
+		xgq_mem_write32(io_hdl, tgt, src[i]);
+}
+
+static inline void xgq_copy_from_ring(uint64_t io_hdl, void *buf, uint64_t src, size_t len)
+{
+	size_t i = 0;
+	uint32_t *tgt = (uint32_t *)buf;
+
+	for (i = 0; i < len / 4; i++, src += 4)
+		tgt[i] = xgq_mem_read32(io_hdl, src);
+}
+
+static inline void xgq_init_ring(struct xgq *xgq, struct xgq_ring *ring,
+				 uint64_t produced, uint64_t consumed, uint64_t slots,
+				 uint32_t slot_num, uint32_t slot_size)
+{
+	ring->xr_xgq = xgq;
+	ring->xr_produced_addr = produced;
+	ring->xr_consumed_addr = consumed;
+	ring->xr_slot_addr = slots;
+	ring->xr_slot_sz = slot_size;
+	ring->xr_slot_num = slot_num;
+	ring->xr_produced = ring->xr_consumed = 0;
+}
+
+static inline int xgq_ring_full(struct xgq_ring *ring)
+{
+	return (ring->xr_produced - ring->xr_consumed) >= ring->xr_slot_num;
+}
+
+static inline int xgq_ring_empty(struct xgq_ring *ring)
+{
+	return ring->xr_produced == ring->xr_consumed;
+}
+
+static inline void xgq_ring_read_produced(uint64_t io_hdl, struct xgq_ring *ring)
+{
+#ifdef BRAM_COLLISION_WORKAROUND
+	ring->xr_produced = xgq_double_read32(io_hdl, ring->xr_produced_addr,
+					      XGQ_IS_IN_MEM_PROD(ring->xr_xgq));
+#else
+	if (unlikely(XGQ_NEED_DOUBLE_READ(ring->xr_xgq))) {
+		ring->xr_produced = xgq_double_read32(io_hdl, ring->xr_produced_addr,
+						      XGQ_IS_IN_MEM_PROD(ring->xr_xgq));
+	} else {
+		ring->xr_produced = xgq_read32(io_hdl, ring->xr_produced_addr,
+					       XGQ_IS_IN_MEM_PROD(ring->xr_xgq));
+	}
+#endif
+}
+
+static inline void xgq_ring_write_produced(uint64_t io_hdl, struct xgq_ring *ring)
+{
+	xgq_write32(io_hdl, ring->xr_produced_addr, ring->xr_produced,
+		    XGQ_IS_IN_MEM_PROD(ring->xr_xgq));
+}
+
+static inline void xgq_ring_read_consumed(uint64_t io_hdl, struct xgq_ring *ring)
+{
+#ifdef BRAM_COLLISION_WORKAROUND
+	ring->xr_consumed = xgq_double_read32(io_hdl, ring->xr_consumed_addr, XGQ_TRUE);
+#else
+	if (unlikely(XGQ_NEED_DOUBLE_READ(ring->xr_xgq)))
+		ring->xr_consumed = xgq_double_read32(io_hdl, ring->xr_consumed_addr, XGQ_TRUE);
+	else
+		ring->xr_consumed = xgq_mem_read32(io_hdl, ring->xr_consumed_addr);
+#endif
+}
+
+static inline void xgq_ring_write_consumed(uint64_t io_hdl, struct xgq_ring *ring)
+{
+	xgq_mem_write32(io_hdl, ring->xr_consumed_addr, ring->xr_consumed);
+}
+
+static inline uint64_t xgq_ring_slot_ptr_produced(struct xgq_ring *ring)
+{
+	return ring->xr_slot_addr +
+	       (uint64_t)ring->xr_slot_sz * (ring->xr_produced & (ring->xr_slot_num - 1));
+}
+
+static inline uint64_t xgq_ring_slot_ptr_consumed(struct xgq_ring *ring)
+{
+	return ring->xr_slot_addr +
+	       (uint64_t)ring->xr_slot_sz * (ring->xr_consumed & (ring->xr_slot_num - 1));
+}
+
+static inline int xgq_can_produce(struct xgq *xgq)
+{
+#ifdef XGQ_SERVER
+	struct xgq_ring *ring = &xgq->xq_cq;
+#else
+	struct xgq_ring *ring = &xgq->xq_sq;
+#endif
+
+	if (likely(!xgq_ring_full(ring)))
+		return XGQ_TRUE;
+	xgq_ring_read_consumed(xgq->xq_io_hdl, ring);
+	return !xgq_ring_full(ring);
+}
+
+static inline int xgq_can_consume(struct xgq *xgq)
+{
+#ifdef XGQ_SERVER
+	struct xgq_ring *ring = &xgq->xq_sq;
+#else
+	struct xgq_ring *ring = &xgq->xq_cq;
+#endif
+
+	if (likely(!xgq_ring_empty(ring)))
+		return XGQ_TRUE;
+	xgq_ring_read_produced(xgq->xq_io_hdl, ring);
+	return !xgq_ring_empty(ring);
+}
+
+/*
+ * Fast forward to where we left. Used only during xgq_attach().
+ */
+static inline void xgq_fast_forward(struct xgq *xgq, struct xgq_ring *ring)
+{
+	xgq_ring_read_produced(xgq->xq_io_hdl, ring);
+	xgq_ring_read_consumed(xgq->xq_io_hdl, ring);
+}
+
+/*
+ * Set consumed to be the same as produced to ignore any existing commands. And there should not
+ * be any left over commands anyway. Used only during xgq_alloc().
+ */
+static inline void xgq_soft_reset(struct xgq *xgq, struct xgq_ring *ring)
+{
+	xgq_ring_read_produced(xgq->xq_io_hdl, ring);
+	ring->xr_consumed = ring->xr_produced;
+	xgq_ring_write_consumed(xgq->xq_io_hdl, ring);
+}
+
+static inline void
+xgq_init(struct xgq *xgq, uint64_t flags, uint64_t io_hdl, uint64_t ring_addr,
+	 size_t n_slots, uint32_t slot_size, uint64_t sq_produced, uint64_t cq_produced)
+{
+	struct xgq_header hdr = {};
+	uint64_t sqprod, cqprod;
+
+	xgq->xq_flags = flags;
+#ifdef BRAM_COLLISION_WORKAROUND
+	xgq->xq_flags |= XGQ_DOUBLE_READ;
+#endif
+	xgq->xq_io_hdl = io_hdl;
+	xgq->xq_header_addr = ring_addr;
+	
+	if (XGQ_IS_IN_MEM_PROD(xgq)) {
+		/* Passed-in sq/cq producer pointer will be ignored. */
+		sqprod = ring_addr + offsetof(struct xgq_header, xh_sq_produced);
+		cqprod = ring_addr + offsetof(struct xgq_header, xh_cq_produced);
+	} else {
+		sqprod = sq_produced;
+		cqprod = cq_produced;
+	}
+	xgq_init_ring(xgq, &xgq->xq_sq, sqprod,
+		      ring_addr + offsetof(struct xgq_header, xh_sq_consumed),
+		      ring_addr + sizeof(struct xgq_header), n_slots, slot_size);
+	xgq_init_ring(xgq, &xgq->xq_cq, cqprod,
+		      ring_addr + offsetof(struct xgq_header, xh_cq_consumed),
+		      ring_addr + sizeof(struct xgq_header) + n_slots * slot_size,
+		      n_slots, sizeof(struct xgq_com_queue_entry));
+
+	hdr.xh_magic = 0;
+	hdr.xh_version = XGQ_VERSION;
+	hdr.xh_slot_num = n_slots;
+	hdr.xh_sq_offset = xgq->xq_sq.xr_slot_addr - ring_addr;
+	hdr.xh_sq_slot_size = slot_size;
+	hdr.xh_cq_offset = xgq->xq_cq.xr_slot_addr - ring_addr;
+	hdr.xh_sq_consumed = 0;
+	hdr.xh_sq_consumed = 0;
+	hdr.xh_cq_produced = 0;
+	hdr.xh_cq_produced = 0;
+	hdr.xh_flags = xgq->xq_flags;
+	xgq_copy_to_ring(xgq->xq_io_hdl, &hdr, ring_addr, sizeof(hdr));
+
+	xgq_soft_reset(xgq, &xgq->xq_sq);
+	xgq_soft_reset(xgq, &xgq->xq_cq);
+
+	// Write the magic number to confirm the header is fully initialized
+	hdr.xh_magic = XGQ_ALLOC_MAGIC;
+	xgq_copy_to_ring(xgq->xq_io_hdl, &hdr, ring_addr, sizeof(uint32_t));
+}
+
+static inline size_t
+xgq_alloc_num_slots(size_t rlen, const uint32_t *slot_size, size_t n_slots)
+{
+	const uint32_t numbits = (sizeof(uint32_t) * 8);
+	uint32_t i = 0;
+	uint32_t total_len = 0;
+	uint32_t numslots = 1;
+
+	while ((total_len <= rlen) && (numslots < (0x1U << (numbits - 1)))) {
+		numslots <<= 1;
+		for (i = 0, total_len = 0; i < n_slots; i++)
+			total_len += xgq_ring_len(numslots, slot_size[i]);
+	}
+	return numslots >> 1;
+}
+
+/*
+ * XGQ APIs.
+ *
+ * Typical flow:
+ *
+ * Client -> xgq_alloc() -> xgq_produce() -> fill-up-SQ-entry -> xgq_notify_peer_produced()
+ * 	  -> xgq_consume() -> process-CQ-entry -> xgq_notify_peer_consumed()
+ *
+ * Server -> xgq_attach() -> xgq_consume() -> process-SQ-entry -> xgq_notify_peer_consumed()
+ * 	  -> xgq_produce() -> fill-up-CQ-entry -> xgq_notify_peer_produced()
+ *
+ * You can call xgq_produce() and fill out entries multiple times before you call
+ * xgq_notify_peer_produced(), which then will publish all entries at once to peer.
+ */
+
+static inline int
+xgq_alloc(struct xgq *xgq, uint64_t flags, uint64_t io_hdl, uint64_t ring_addr, size_t *ring_len,
+	  uint32_t slot_size, uint64_t sq_produced, uint64_t cq_produced)
+{
+	uint32_t numslots = 0;
+	size_t rlen = *ring_len;
+
+	if (slot_size % sizeof(uint32_t))
+		return -EINVAL;
+
+	numslots = xgq_alloc_num_slots(rlen, &slot_size, 1);
+	if (numslots < XGQ_MIN_NUM_SLOTS)
+		return -E2BIG;
+
+	xgq_init(xgq, flags, io_hdl, ring_addr, numslots, slot_size, sq_produced, cq_produced);
+	*ring_len = xgq_ring_len(numslots, slot_size);
+	return 0;
+}
+
+/*
+ * Alloc a group of XGQs on the ring buffer. Producer pointers will be embedded in the header.
+ */
+static inline int
+xgq_group_alloc(struct xgq *a_xgq, size_t n_qs, uint64_t flags, uint64_t io_hdl, uint64_t ring_addr,
+		size_t *ring_len, const uint32_t *a_slot_size, const uint32_t max_slots)
+{
+	size_t i;
+	uint32_t numslots = 0;
+	size_t rlen = *ring_len;
+	uint64_t raddr = ring_addr;
+
+	/* Only support in-mem producer pointer for group xgq alloc. */
+	flags |= XGQ_IN_MEM_PROD;
+
+	for (i = 0; i < n_qs; i++) {
+		if (a_slot_size[i] % sizeof(uint32_t))
+			return -EINVAL;
+	}
+
+	numslots = xgq_alloc_num_slots(rlen, a_slot_size, n_qs);
+	if (numslots < XGQ_MIN_NUM_SLOTS)
+		return -E2BIG;
+	if (max_slots && numslots > max_slots)
+		numslots = max_slots;
+
+	for (i = 0; i < n_qs; i++) {
+		xgq_init(&a_xgq[i], flags, io_hdl, raddr, numslots, a_slot_size[i], 0, 0);
+		raddr += xgq_ring_len(numslots, a_slot_size[i]);
+	}
+
+	*ring_len = raddr - ring_addr;
+	return 0;
+}
+
+static inline int xgq_attach(struct xgq *xgq, uint64_t flags, uint64_t io_hdl, uint64_t ring_addr,
+			     uint64_t sq_produced, uint64_t cq_produced)
+{
+	struct xgq_header hdr = {};
+	uint32_t nslots;
+	uint64_t sqprod, cqprod;
+
+	xgq_copy_from_ring(xgq->xq_io_hdl, &hdr, ring_addr, sizeof(uint32_t));
+	// Magic number must show up to confirm the header is fully initialized
+	if (hdr.xh_magic != XGQ_ALLOC_MAGIC)
+		return -EAGAIN;
+
+	xgq_copy_from_ring(xgq->xq_io_hdl, &hdr, ring_addr, sizeof(struct xgq_header));
+	if (GET_XGQ_MAJOR(hdr.xh_version) != XGQ_MAJOR)
+		return -EOPNOTSUPP;
+
+	nslots = hdr.xh_slot_num;
+	if ((nslots < XGQ_MIN_NUM_SLOTS) || (nslots & (nslots - 1)))
+		return -EPROTO;
+
+	xgq->xq_flags = 0;
+	xgq->xq_flags |= flags;
+	xgq->xq_flags |= (hdr.xh_flags & XGQ_DOUBLE_READ);
+	xgq->xq_flags |= (hdr.xh_flags & XGQ_IN_MEM_PROD);
+
+	if (XGQ_IS_IN_MEM_PROD(xgq)) {
+		/* Passed-in sq/cq producer pointer will be ignored. */
+		sqprod = ring_addr + offsetof(struct xgq_header, xh_sq_produced);
+		cqprod = ring_addr + offsetof(struct xgq_header, xh_cq_produced);
+	} else {
+		sqprod = sq_produced;
+		cqprod = cq_produced;
+	}
+	xgq_init_ring(xgq, &xgq->xq_sq, sqprod,
+		      ring_addr + offsetof(struct xgq_header, xh_sq_consumed),
+		      ring_addr + hdr.xh_sq_offset,
+		      hdr.xh_slot_num, hdr.xh_sq_slot_size);
+	xgq_init_ring(xgq, &xgq->xq_cq, cqprod,
+		      ring_addr + offsetof(struct xgq_header, xh_cq_consumed),
+		      ring_addr + hdr.xh_cq_offset,
+		      hdr.xh_slot_num, sizeof(struct xgq_com_queue_entry));
+
+	xgq_fast_forward(xgq, &xgq->xq_sq);
+	xgq_fast_forward(xgq, &xgq->xq_cq);
+	return 0;
+}
+
+static inline int xgq_produce(struct xgq *xgq, uint64_t *slot_addr)
+{
+#ifdef XGQ_SERVER
+	struct xgq_ring *ring = &xgq->xq_cq;
+#else
+	struct xgq_ring *ring = &xgq->xq_sq;
+#endif
+
+	if (unlikely(!xgq_can_produce(xgq)))
+		return -ENOSPC;
+	*slot_addr = xgq_ring_slot_ptr_produced(ring);
+	ring->xr_produced++;
+	return 0;
+}
+
+static inline int xgq_consume(struct xgq *xgq, uint64_t *slot_addr)
+{
+#ifdef XGQ_OUT_OF_ORDER_WRITE
+	uint32_t val = 0;
+#endif
+#ifdef XGQ_SERVER
+	struct xgq_ring *ring = &xgq->xq_sq;
+#else
+	struct xgq_ring *ring = &xgq->xq_cq;
+#endif
+
+	if (unlikely(!xgq_can_consume(xgq)))
+		return -ENOENT;
+	*slot_addr = xgq_ring_slot_ptr_consumed(ring);
+	ring->xr_consumed++;
+
+#ifdef XGQ_OUT_OF_ORDER_WRITE
+	/*
+	 * Producer pointer does not gurantee the slot content is up-to-date.
+	 * See comments above XGQ_ENTRY_NEW_FLAG_MASK for details.
+	 */
+	while (!(val & XGQ_ENTRY_NEW_FLAG_MASK))
+		val = xgq_mem_read32(xgq->xq_io_hdl, *slot_addr);
+	xgq_mem_write32(xgq->xq_io_hdl, *slot_addr, val & ~XGQ_ENTRY_NEW_FLAG_MASK);
+#endif
+
+	return 0;
+}
+
+static inline void xgq_notify_peer_produced(struct xgq *xgq)
+{
+#ifdef XGQ_SERVER
+	xgq_ring_write_produced(xgq->xq_io_hdl, &xgq->xq_cq);
+#else
+	xgq_ring_write_produced(xgq->xq_io_hdl, &xgq->xq_sq);
+#endif
+
+}
+
+static inline void xgq_notify_peer_consumed(struct xgq *xgq)
+{
+#ifdef XGQ_SERVER
+	xgq_ring_write_consumed(xgq->xq_io_hdl, &xgq->xq_sq);
+#else
+	xgq_ring_write_consumed(xgq->xq_io_hdl, &xgq->xq_cq);
+#endif
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xgq_resp_parser.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xgq_resp_parser.h
@@ -0,0 +1,116 @@
+/*
+ *  Copyright (C) 2021-2022, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef XGQ_RESP_PARSER_H
+#define XGQ_RESP_PARSER_H
+
+#define SDR_NULL_BYTE	0x00
+#define SDR_LENGTH_MASK	0x3F
+#define SDR_TYPE_MASK	0x03
+#define SDR_TYPE_POS	6
+
+#define SDR_COMPLETE_IDX  0
+#define SDR_REPO_IDX      1
+#define SDR_REPO_VER_IDX  2
+#define SDR_NUM_REC_IDX   3
+#define SDR_NUM_BYTES_IDX 4
+#define SDR_HEADER_SIZE   5
+
+#define SDR_EOR_BYTES     3
+
+#define THRESHOLD_UPPER_WARNING_MASK	(0x1 << 0)
+#define THRESHOLD_UPPER_CRITICAL_MASK	(0x1 << 1)
+#define THRESHOLD_UPPER_FATAL_MASK		(0x1 << 2)
+#define THRESHOLD_LOWER_WARNING_MASK	(0x1 << 3)
+#define THRESHOLD_LOWER_CRITICAL_MASK	(0x1 << 4)
+#define THRESHOLD_LOWER_FATAL_MASK		(0x1 << 5)
+#define THRESHOLD_SENSOR_AVG_MASK		(0x1 << 6)
+#define THRESHOLD_SENSOR_MAX_MASK		(0x1 << 7)
+
+enum xgq_sdr_repo_type {
+    SDR_TYPE_GET_SIZE     = 0x00,
+    SDR_TYPE_BDINFO       = 0xC0,
+    SDR_TYPE_TEMP         = 0xC1,
+    SDR_TYPE_VOLTAGE      = 0xC2,
+    SDR_TYPE_CURRENT      = 0xC3,
+    SDR_TYPE_POWER        = 0xC4,
+    SDR_TYPE_QSFP         = 0xC5,
+    SDR_TYPE_VPD_PCIE     = 0xD0,
+    SDR_TYPE_IPMIFRU      = 0xD1,
+    SDR_TYPE_CSDR_LOGDATA = 0xE0,
+    SDR_TYPE_VMC_LOGDATA  = 0xE1,
+    SDR_TYPE_MAX	  = 11,//increment if new entry added in this enum
+};
+
+enum xgq_sdr_completion_code {
+    SDR_CODE_NOT_AVAILABLE            = 0x00,
+    SDR_CODE_OP_SUCCESS               = 0x01,
+    SDR_CODE_OP_FAILED                = 0x02,
+    SDR_CODE_FLOW_CONTROL_READ_STALE  = 0x03,
+    SDR_CODE_FLOW_CONTROL_WRITE_ERROR = 0x04,
+    SDR_CODE_INVALID_SENSOR_ID        = 0x05,
+};
+
+enum sensor_record_fields {
+    SENSOR_ID = 0,
+    SENSOR_NAME_TL,
+    SENSOR_NAME,
+    SENSOR_VALUE_TL,
+    SENSOR_VALUE,
+    SENSOR_BASEUNIT_TL,
+    SENSOR_BASEUNIT,
+    SENSOR_UNIT_MODIFIER,
+    SENSOR_THRESHOLD_SUPPORT,
+    SENSOR_LOWER_FATAL,
+    SENSOR_LOWER_CRITICAL,
+    SENSOR_LOWER_WARNING,
+    SENSOR_UPPER_FATAL,
+    SENSOR_UPPER_CRITICAL,
+    SENSOR_UPPER_WARNING,
+    SENSOR_STATUS,
+    SENSOR_MAX_VAL,
+    SENSOR_AVG_VAL,
+};
+
+enum sensor_status {
+    SENSOR_NOT_PRESENT          = 0x00,
+    SENSOR_PRESENT_AND_VALID    = 0x01,
+    DATA_NOT_AVAILABLE          = 0x02,
+    SENSOR_STATUS_NOT_AVAILABLE = 0x7F,
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xrt_cu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xrt_cu.h
@@ -0,0 +1,568 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Unify CU Model
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: min.ma@xilinx.com
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_CU_H
+#define _XRT_CU_H
+
+#include <linux/version.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/semaphore.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/kthread.h>
+#include <linux/circ_buf.h>
+#include "kds_command.h"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+#define ioremap_nocache         ioremap
+#endif
+
+#define MAX_CUS 128
+#define MAX_SLOT 32
+
+/* Soft kernel indices are numbered from 0 to some MAX_CUS
+ * but are in a distinct domain which is indiciated by the
+ * first 16 bit of the index used to identify the soft kernel
+ */
+#define SCU_DOMAIN 0x10000
+#define	SOFT_KERNEL_REG_SIZE	4096
+
+/* The normal CU in ip_layout would assign a interrupt
+ * ID in range 0 to 127. Use 128 for m2m cu could ensure
+ * m2m CU is at the end of the CU, which is compatible with
+ * legacy implementation.
+ */
+#define M2M_CU_ID 128
+
+#define xcu_info(xcu, fmt, args...)			\
+	dev_info(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+#define xcu_warn(xcu, fmt, args...)			\
+	dev_warn(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+#define xcu_err(xcu, fmt, args...)			\
+	dev_err(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+#define xcu_dbg(xcu, fmt, args...)			\
+	dev_dbg(xcu->dev, " %llx %s: "fmt, (u64)xcu->dev, __func__, ##args)
+
+/* XRT CU timer macros */
+/* A low frequence timer per CU to check if CU/command timeout */
+#define CU_TICKS_PER_SEC	2
+#define CU_TIMER		(HZ / CU_TICKS_PER_SEC) /* in jiffies */
+#define CU_EXEC_DEFAULT_TTL	(5UL * CU_TICKS_PER_SEC)
+
+/* HLS CU macros */
+#define CU_AP_START	(0x1 << 0)
+#define CU_AP_DONE	(0x1 << 1)
+#define CU_AP_IDLE	(0x1 << 2)
+#define CU_AP_READY	(0x1 << 3)
+#define CU_AP_CONTINUE	(0x1 << 4)
+#define CU_AP_RESET	(0x1 << 5)
+#define CU_AP_SW_RESET	(0x1 << 8)
+/* Special macro(s) which not defined by HLS CU */
+#define CU_AP_CRASHED	(0xFFFFFFFF)
+
+#define CU_INTR_DONE  0x1
+#define CU_INTR_READY 0x2
+
+enum xcu_model {
+	XCU_HLS,
+	XCU_ACC,
+	XCU_FA,
+	XCU_XGQ,
+	XCU_AUTO,
+};
+
+enum xcu_config_type {
+	CONSECUTIVE_T,
+	PAIRS_T,
+	XGQ_T,
+};
+
+enum xcu_process_result {
+	XCU_IDLE = 0,
+	XCU_BUSY,
+};
+
+/* Let's use HLS style status bits in new_status
+ * Bit 0: start (running)
+ * Bit 1: done
+ * Bit 2: idle
+ */
+struct xcu_status {
+	u32	num_done;
+	u32	num_ready;
+	u32	new_status;
+	u32	rcode;
+};
+
+typedef void *xcu_core_t;
+struct xcu_funcs {
+	/**
+	 * @alloc_credit:
+	 *
+	 * Try to alloc one credit on the CU. A credit is required before
+	 * submit a task to the CU. Otherwise, it would lead to unknown CU
+	 * behaviour.
+	 * Return: the number of remaining credit.
+	 */
+	int (*alloc_credit)(void *core);
+
+	/**
+	 * @free_credit:
+	 *
+	 * free credits.
+	 */
+	void (*free_credit)(void *core, u32 count);
+
+	/**
+	 * @peek_credit:
+	 *
+	 * Check how many credits the CU could provide with side effect.
+	 */
+	int (*peek_credit)(void *core);
+
+	/**
+	 * @configure:
+	 *
+	 * Congifure CU arguments.
+	 *
+	 * There are two types of configuration format.
+	 *
+	 * 1. CONSECUTIVE: Which is a blind copy from data to CU.
+	 * 2. PAIRS: The data contains {offset, val} pairs.
+	 * 3. XGQ: The data contains a XGQ command.
+	 */
+	int (*configure)(void *core, u32 *data, size_t sz, int type);
+
+	/**
+	 * @start:
+	 *
+	 * Start a CU.
+	 */
+	void (*start)(void *core);
+
+	/**
+	 * @check:
+	 *
+	 * Check CU status and the pending task status.
+	 */
+	void (*check)(void *core, struct xcu_status *status, bool force);
+
+	/**
+	 * @submit_config:
+	 *
+	 * This is like configure CU. But it takes xcmd and own it.
+	 *
+	 */
+	int (*submit_config)(void *core, struct kds_command *xcmd);
+
+	/**
+	 * @get_complete:
+	 *
+	 * Get next completed xcmd.
+	 *
+	 */
+	struct kds_command *(*get_complete)(void *core);
+
+	/**
+	 * @abort:
+	 *
+	 */
+	int (*abort)(void *core, void *cond, bool (*match)(struct kds_command *xcmd, void *cond));
+
+	/**
+	 * @reset:
+	 *
+	 * Reset CU.
+	 */
+	void (*reset)(void *core);
+
+	/**
+	 * @reset_done:
+	 *
+	 * Check if CU is properly reset
+	 */
+	bool (*reset_done)(void *core);
+
+	/**
+	 * @enable_intr:
+	 *
+	 * Enable interrupt. Support DONE and READY interrupt.
+	 */
+	void (*enable_intr)(void *core, u32 intr_type);
+
+	/**
+	 * @disable_intr:
+	 *
+	 * Disable interrupt.
+	 */
+	void (*disable_intr)(void *core, u32 intr_type);
+
+	/**
+	 * @clear_intr:
+	 *
+	 * Clear interrupt.
+	 */
+	u32 (*clear_intr)(void *core);
+};
+
+enum arg_dir {
+	DIR_NONE = 0,
+	DIR_INPUT,
+	DIR_OUTPUT
+};
+
+struct xrt_cu_arg {
+	char	name[64];
+	u32	offset;
+	u32	size;
+	u32	dir;
+};
+
+enum CU_PROTOCOL {
+	CTRL_HS = 0,
+	CTRL_CHAIN = 1,
+	CTRL_NONE = 2,
+	CTRL_ME = 3,
+	CTRL_ACC = 4,
+	CTRL_FA = 5
+};
+
+struct xrt_cu_info {
+	u32			 model;
+	int			 cu_idx;
+	u32			 slot_idx;
+	int			 inst_idx;
+	u64			 addr;
+	size_t			 size;
+	u32			 protocol;
+	u32			 intr_id;
+	u32			 is_m2m;
+	u32			 num_res;
+	bool			 intr_enable;
+	bool			 sw_reset;
+	struct xrt_cu_arg	*args;
+	u32			 num_args;
+	char			 iname[64];
+	char			 kname[64];
+	void			*xgq;
+	int			 cu_domain;
+	unsigned char		 uuid[16];
+};
+
+struct per_custat {
+	u64		usage;
+};
+
+#define CU_STATE_GOOD  0x1
+#define CU_STATE_BAD   0x2
+
+/* The Buf size and xrt_cu_log size must be power of 2 */
+#define CIRC_BUF_SIZE 2 * 4096
+struct xrt_cu_log {
+	u64		stage:32;
+	uintptr_t	cmd_id:32;
+	u64		ts;
+};
+#define CU_LOG_STAGE_RQ		1
+#define CU_LOG_STAGE_ISR	2
+#define CU_LOG_STAGE_SQ		3
+#define CU_LOG_STAGE_CQ		4
+
+/* Supported event type */
+struct xrt_cu {
+	struct device		 *dev;
+	struct xrt_cu_info	  info;
+	struct resource		**res;
+	struct list_head	  cu;
+	/* pending queue */
+	struct list_head	  pq;
+	spinlock_t		  pq_lock;
+	u32			  num_pq;
+	/* high priority queue */
+	struct list_head	  hpq;
+	spinlock_t		  hpq_lock;
+	u32			  num_hpq;
+	struct completion	  comp;
+	/*
+	 * Pending Q is used in thread that is submitting CU cmds.
+	 * Other Qs are used in thread that is completing them.
+	 * In order to prevent false sharing, they need to be in different
+	 * cache lines.
+	 */
+	/* run queue */
+	struct list_head	  rq ____cacheline_aligned_in_smp;
+	u32			  num_rq;
+	/* submitted queue */
+	u32			  num_sq;
+	/* completed queue */
+	struct list_head	  cq;
+	u32			  num_cq;
+	struct semaphore	  sem;
+	struct semaphore	  sem_cu;
+	void			 *core;
+	u32			  stop;
+	bool			  bad_state;
+	u32			  done_cnt;
+	u32			  ready_cnt;
+	u32			  status;
+	u32			  rcode;
+	int			  busy_threshold;
+	u32			  interval_min;
+	u32			  interval_max;
+	struct kds_command	 *old_cmd;
+
+	struct mutex		  ev_lock;
+	struct list_head	  events;
+
+	struct timer_list	  timer;
+	atomic_t		  tick;
+	u32			  start_tick;
+
+	struct per_custat	  cu_stat;
+
+	/**
+	 * @funcs:
+	 *
+	 * Compute unit functions.
+	 */
+	struct xcu_funcs          *funcs;
+	/* TODO: Maybe rethink if we should use two threads,
+	 * one for submit, one for complete
+	 */
+	struct task_struct	  *thread;
+	/* Good for debug */
+	u32			   sleep_cnt;
+	u32			   max_running;
+
+	/* support user management CU interrupt */
+	DECLARE_BITMAP(is_ucu, 1);
+	wait_queue_head_t	   ucu_waitq;
+	atomic_t		   ucu_event;
+	int (* user_manage_irq)(struct xrt_cu *xcu, bool user_manage);
+	int (* configure_irq)(struct xrt_cu *xcu, bool enable);
+
+	/* For debug/analysis */
+	char			   debug;
+	char			   log_buf[CIRC_BUF_SIZE] __aligned(sizeof(u64));
+	struct circ_buf		   crc_buf;
+};
+
+static inline char *prot2str(enum CU_PROTOCOL prot)
+{
+	switch (prot) {
+	case CTRL_HS:		return "CTRL_HS";
+	case CTRL_CHAIN:	return "CTRL_CHAIN";
+	case CTRL_NONE:		return "CTRL_NONE";
+	case CTRL_ME:		return "CTRL_ME";
+	case CTRL_ACC:		return "CTRL_ACC";
+	case CTRL_FA:		return "CTRL_FA";
+	default:		return "UNKNOWN";
+	}
+}
+
+static void inline xrt_cu_enable_intr(struct xrt_cu *xcu, u32 intr_type)
+{
+	if (xcu->funcs)
+		xcu->funcs->enable_intr(xcu->core, intr_type);
+}
+
+static void inline xrt_cu_disable_intr(struct xrt_cu *xcu, u32 intr_type)
+{
+	if (xcu->funcs)
+		xcu->funcs->disable_intr(xcu->core, intr_type);
+}
+
+static u32 inline xrt_cu_clear_intr(struct xrt_cu *xcu)
+{
+	return xcu->funcs ? xcu->funcs->clear_intr(xcu->core) : 0;
+}
+
+static inline int xrt_cu_config(struct xrt_cu *xcu, u32 *data, size_t sz, int type)
+{
+	return xcu->funcs->configure(xcu->core, data, sz, type);
+}
+
+static inline void xrt_cu_start(struct xrt_cu *xcu)
+{
+	xcu->funcs->start(xcu->core);
+}
+
+static inline int xrt_cu_submit_config(struct xrt_cu *xcu, struct kds_command *xcmd)
+{
+	if (!xcu->funcs->submit_config)
+		return -EINVAL;
+
+	return xcu->funcs->submit_config(xcu->core, xcmd);
+}
+
+static inline struct kds_command *xrt_cu_get_complete(struct xrt_cu *xcu)
+{
+	if (!xcu->funcs->get_complete)
+		return NULL;
+
+	return xcu->funcs->get_complete(xcu->core);
+}
+
+static inline int
+xrt_cu_cmd_abort(struct xrt_cu *xcu, void *cond,
+		 bool (*match)(struct kds_command *xcmd, void *cond))
+{
+	if (!xcu->funcs->abort)
+		return -EINVAL;
+
+	return xcu->funcs->abort(xcu->core, cond, match);
+}
+
+static inline void xrt_cu_reset(struct xrt_cu *xcu)
+{
+	xcu->funcs->reset(xcu->core);
+}
+
+static inline bool xrt_cu_reset_done(struct xrt_cu *xcu)
+{
+	return xcu->funcs->reset_done(xcu->core);
+}
+
+static inline void __xrt_cu_check(struct xrt_cu *xcu, bool force)
+{
+	struct xcu_status status;
+
+	status.num_done = 0;
+	status.num_ready = 0;
+	status.new_status = 0;
+	status.rcode = 0;
+	xcu->funcs->check(xcu->core, &status, force);
+	/* XRT CU assume command finished in order */
+	xcu->done_cnt += status.num_done;
+	xcu->ready_cnt += status.num_ready;
+	xcu->status = status.new_status;
+	xcu->rcode  = status.rcode;
+}
+
+static inline void xrt_cu_check(struct xrt_cu *xcu)
+{
+	__xrt_cu_check(xcu, false);
+}
+
+static inline void xrt_cu_check_force(struct xrt_cu *xcu)
+{
+	__xrt_cu_check(xcu, true);
+}
+
+static inline int xrt_cu_get_credit(struct xrt_cu *xcu)
+{
+	return xcu->funcs->alloc_credit(xcu->core);
+}
+
+static inline int is_zero_credit(struct xrt_cu *xcu)
+{
+	return (xcu->funcs->peek_credit(xcu->core) == 0);
+}
+
+static inline int xrt_cu_peek_credit(struct xrt_cu *xcu)
+{
+	return xcu->funcs->peek_credit(xcu->core);
+}
+
+static inline void xrt_cu_put_credit(struct xrt_cu *xcu, u32 count)
+{
+	xcu->funcs->free_credit(xcu->core, count);
+}
+
+/* This is a bit trick to calculate next highest power of 2.
+ * If size is a power of 2, the return would be the same as size.
+ */
+static __attribute__((unused))
+u32 round_up_to_next_power2(u32 size)
+{
+	u32 v = --size;
+	v |= v >> 1;
+	v |= v >> 2;
+	v |= v >> 4;
+	v |= v >> 8;
+	v |= v >> 16;
+	return ++v;
+}
+
+/* 1. Move commands from pending command queue to running queue
+ * 2. If CU is ready, submit command(Configure hardware)
+ * 3. Check if submitted command is completed or not
+ */
+void xrt_cu_submit(struct xrt_cu *xcu, struct kds_command *xcmd);
+void xrt_cu_hpq_submit(struct xrt_cu *xcu, struct kds_command *xcmd);
+void xrt_cu_abort(struct xrt_cu *xcu, struct kds_client *client);
+bool xrt_cu_abort_done(struct xrt_cu *xcu, struct kds_client *client);
+int xrt_cu_cfg_update(struct xrt_cu *xcu, int intr);
+int xrt_fa_cfg_update(struct xrt_cu *xcu, u64 bar, u64 dev, void __iomem *vaddr, u32 num_slots);
+int xrt_is_fa(struct xrt_cu *xcu, u32 *size);
+int xrt_cu_get_protocol(struct xrt_cu *xcu);
+u32 xrt_cu_get_status(struct xrt_cu *xcu);
+int xrt_cu_regmap_size(struct xrt_cu *xcu);
+
+int  xrt_cu_init(struct xrt_cu *xcu);
+void xrt_cu_fini(struct xrt_cu *xcu);
+
+ssize_t show_cu_stat(struct xrt_cu *xcu, char *buf);
+ssize_t show_cu_info(struct xrt_cu *xcu, char *buf);
+ssize_t show_formatted_cu_stat(struct xrt_cu *xcu, char *buf);
+
+void xrt_cu_circ_produce(struct xrt_cu *xcu, u32 stage, uintptr_t cmd);
+ssize_t xrt_cu_circ_consume_all(struct xrt_cu *xcu, char *buf, size_t size);
+
+int xrt_cu_process_queues(struct xrt_cu *xcu);
+
+/* CU Implementations */
+int xrt_cu_hls_init(struct xrt_cu *xcu);
+void xrt_cu_hls_fini(struct xrt_cu *xcu);
+
+typedef struct {
+	u32 argOffset;
+	u32 argSize;
+	u32 argValue[];
+} descEntry_t;
+
+typedef struct {
+	u32 status;
+	u32 numInputEntries;
+	u32 inputEntryBytes;
+	u32 numOutputEntries;
+	u32 outputEntryBytes;
+	u32 data[];
+} descriptor_t;
+
+#define to_cu_fa(core) ((struct xrt_cu_fa *)(core))
+struct xrt_cu_fa {
+	void __iomem		*vaddr;
+	void __iomem		*cmdmem;
+	u64			 paddr;
+	u32			 slot_sz;
+	u32			 num_slots;
+	u32			 head_slot;
+	u32			 desc_msw;
+	u32			 task_cnt;
+	int			 max_credits;
+	int			 credits;
+	int			 run_cnts;
+	u64			 check_count;
+
+	struct list_head	 submitted;
+	struct list_head	 completed;
+};
+
+int xrt_cu_fa_init(struct xrt_cu *xcu);
+void xrt_cu_fa_fini(struct xrt_cu *xcu);
+
+int xrt_cu_scu_init(struct xrt_cu *xcu, void *vaddr, struct semaphore *sem);
+void xrt_cu_scu_fini(struct xrt_cu *xcu);
+
+#endif /* _XRT_CU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xrt_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xrt_drv.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style device manager for PCIe based OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_DRV_H
+#define _XRT_DRV_H
+
+#define XRT_DRV_BO_DEVICE_MEM 	(1 << 31)
+#define XRT_DRV_BO_HOST_MEM	(1 << 30)
+#define XRT_DRV_BO_DRV_ALLOC	(1 << 29)
+#define XRT_DRV_BO_DRM_IMPORT 	(1 << 28)
+#define XRT_DRV_BO_P2P		(1 << 27)
+#define XRT_DRV_BO_DRM_SHMEM	(1 << 26)
+#define XRT_DRV_BO_USER_ALLOC	(1 << 25)
+#define XRT_DRV_BO_CMA		(1 << 24)
+#define XRT_DRV_BO_CACHEABLE	(1 << 23)
+#define XRT_DRV_BO_SGL		(1 << 22)
+#define XRT_DRV_BO_KERN_BUF	(1 << 21)
+
+/* Versal transfer cache packet definition */
+
+#define	XRT_XFR_VER			1
+
+/*
+ * Note: we should keep the existing PKT status and flags
+ *       stable to not breaking the old versal platform
+ */
+#define	XRT_XFR_PKT_STATUS_IDLE		0
+#define	XRT_XFR_PKT_STATUS_NEW		1
+#define	XRT_XFR_PKT_STATUS_DONE		2
+#define	XRT_XFR_PKT_STATUS_FAIL		3
+
+#define	XRT_XFR_PKT_TYPE_SHIFT		1
+#define	XRT_XFR_PKT_TYPE_MASK		7
+
+#define	XRT_XFR_PKT_VER_SHIFT		4
+#define	XRT_XFR_PKT_VER_MASK		3
+
+#define	XRT_XFR_PKT_TYPE_PDI		0
+#define	XRT_XFR_PKT_TYPE_XCLBIN		1
+
+#define	XRT_XFR_PKT_FLAGS_LAST		(1 << 0)
+#define	XRT_XFR_PKT_FLAGS_PDI		(XRT_XFR_PKT_TYPE_PDI << \
+	XRT_XFR_PKT_TYPE_SHIFT)
+#define	XRT_XFR_PKT_FLAGS_XCLBIN	(XRT_XFR_PKT_TYPE_XCLBIN << \
+	XRT_XFR_PKT_TYPE_SHIFT)
+#define	XRT_XFR_PKT_FLAGS_VER		(XRT_XFR_VER << XRT_XFR_PKT_VER_SHIFT)
+
+struct pdi_packet {
+	union {
+		struct {
+			u8	pkt_status;
+			u8	pkt_flags;
+			u16	pkt_size;
+		};
+		u32 header;
+	};
+} __packed;
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xrt_error_code.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xrt_error_code.h
@@ -0,0 +1,156 @@
+/*
+ *  Copyright (C) 2020, Xilinx Inc
+ *
+ *  This file is dual licensed.  It may be redistributed and/or modified
+ *  under the terms of the Apache 2.0 License OR version 2 of the GNU
+ *  General Public License.
+ *
+ *  Apache License Verbiage
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License");
+ *  you may not use this file except in compliance with the License.
+ *  You may obtain a copy of the License at
+ *
+ *  http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software
+ *  distributed under the License is distributed on an "AS IS" BASIS,
+ *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ *  See the License for the specific language governing permissions and
+ *  limitations under the License.
+ *
+ *  GPL license Verbiage:
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License as
+ *  published by the Free Software Foundation; either version 2 of the
+ *  License, or (at your option) any later version.  This program is
+ *  distributed in the hope that it will be useful, but WITHOUT ANY
+ *  WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ *  License for more details.  You should have received a copy of the
+ *  GNU General Public License along with this program; if not, write
+ *  to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+ *  Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef XRT_ERROR_CODE_H_
+#define XRT_ERROR_CODE_H_
+
+#if defined(__KERNEL__)
+# include <linux/types.h>
+#elif defined(__cplusplus)
+# include <cstdint>
+#else
+# include <stdint.h>
+#endif
+
+/**
+ * xrtErrorCode layout
+ *
+ * This layout is internal to XRT (akin to a POSIX error code).
+ *
+ * The error code is populated by driver and consumed by XRT
+ * implementation where it is translated into an actual error / info /
+ * warning that is propagated to the end user.
+ *
+ * 63 - 48  47 - 40   39 - 32   31 - 24   23 - 16    15 - 0
+ * --------------------------------------------------------
+ * |    |    |    |    |    |    |    |    |    |    |----| xrtErrorNum
+ * |    |    |    |    |    |    |    |    |----|---------- xrtErrorDriver
+ * |    |    |    |    |    |    |----|-------------------- xrtErrorSeverity
+ * |    |    |    |    |----|------------------------------ xrtErrorModule
+ * |    |    |----|---------------------------------------- xrtErrorClass
+ * |----|-------------------------------------------------- reserved
+ *
+ */
+typedef uint64_t xrtErrorCode;
+typedef uint64_t xrtErrorTime;
+
+#define XRT_ERROR_NUM_MASK		0xFFFFUL
+#define XRT_ERROR_NUM_SHIFT		0
+#define XRT_ERROR_DRIVER_MASK		0xFUL
+#define XRT_ERROR_DRIVER_SHIFT		16
+#define XRT_ERROR_SEVERITY_MASK		0xFUL
+#define XRT_ERROR_SEVERITY_SHIFT	24
+#define XRT_ERROR_MODULE_MASK		0xFUL
+#define XRT_ERROR_MODULE_SHIFT		32
+#define XRT_ERROR_CLASS_MASK		0xFUL
+#define XRT_ERROR_CLASS_SHIFT		40
+
+#define	XRT_ERROR_CODE_BUILD(num, driver, severity, module, eclass) \
+	((((num) & XRT_ERROR_NUM_MASK) << XRT_ERROR_NUM_SHIFT) | \
+	(((driver) & XRT_ERROR_DRIVER_MASK) << XRT_ERROR_DRIVER_SHIFT) | \
+	(((severity) & XRT_ERROR_SEVERITY_MASK) << XRT_ERROR_SEVERITY_SHIFT) | \
+	(((module) & XRT_ERROR_MODULE_MASK) << XRT_ERROR_MODULE_SHIFT) | \
+	(((eclass) & XRT_ERROR_CLASS_MASK) << XRT_ERROR_CLASS_SHIFT))
+
+#define XRT_ERROR_NUM(code) (((code) >> XRT_ERROR_NUM_SHIFT) & XRT_ERROR_NUM_MASK)
+#define XRT_ERROR_DRIVER(code) (((code) >> XRT_ERROR_DRIVER_SHIFT) & XRT_ERROR_DRIVER_MASK)
+#define XRT_ERROR_SEVERITY(code) (((code) >> XRT_ERROR_SEVERITY_SHIFT) & XRT_ERROR_SEVERITY_MASK)
+#define XRT_ERROR_MODULE(code) (((code) >> XRT_ERROR_MODULE_SHIFT) & XRT_ERROR_MODULE_MASK)
+#define XRT_ERROR_CLASS(code) (((code) >> XRT_ERROR_CLASS_SHIFT) & XRT_ERROR_CLASS_MASK)
+
+/**
+ * xrt_error_num - XRT specific error numbers
+ */
+enum xrtErrorNum {
+  XRT_ERROR_NUM_FIRWWALL_TRIP = 1,
+  XRT_ERROR_NUM_TEMP_HIGH,
+  XRT_ERROR_NUM_AIE_SATURATION,
+  XRT_ERROR_NUM_AIE_FP,
+  XRT_ERROR_NUM_AIE_STREAM,
+  XRT_ERROR_NUM_AIE_ACCESS,
+  XRT_ERROR_NUM_AIE_BUS,
+  XRT_ERROR_NUM_AIE_INSTRUCTION,
+  XRT_ERROR_NUM_AIE_ECC,
+  XRT_ERROR_NUM_AIE_LOCK,
+  XRT_ERROR_NUM_AIE_DMA,
+  XRT_ERROR_NUM_AIE_MEM_PARITY,
+  XRT_ERROR_NUM_KDS_CU,
+  XRT_ERROR_NUM_KDS_EXEC,
+  XRT_ERROR_NUM_UNKNOWN
+};
+
+enum xrtErrorDriver {
+  XRT_ERROR_DRIVER_XOCL = 1,
+  XRT_ERROR_DRIVER_XCLMGMT,
+  XRT_ERROR_DRIVER_ZOCL,
+  XRT_ERROR_DRIVER_AIE,
+  XRT_ERROR_DRIVER_UNKNOWN
+};
+
+enum xrtErrorSeverity {
+  XRT_ERROR_SEVERITY_EMERGENCY = 1,
+  XRT_ERROR_SEVERITY_ALERT,
+  XRT_ERROR_SEVERITY_CRITICAL,
+  XRT_ERROR_SEVERITY_ERROR,
+  XRT_ERROR_SEVERITY_WARNING,
+  XRT_ERROR_SEVERITY_NOTICE,
+  XRT_ERROR_SEVERITY_INFO,
+  XRT_ERROR_SEVERITY_DEBUG,
+  XRT_ERROR_SEVERITY_UNKNOWN
+};
+
+enum xrtErrorModule {
+  XRT_ERROR_MODULE_FIREWALL = 1,
+  XRT_ERROR_MODULE_CMC,
+  XRT_ERROR_MODULE_AIE_CORE,
+  XRT_ERROR_MODULE_AIE_MEMORY,
+  XRT_ERROR_MODULE_AIE_SHIM,
+  XRT_ERROR_MODULE_AIE_NOC,
+  XRT_ERROR_MODULE_AIE_PL,
+  XRT_ERROR_MODULE_UNKNOWN
+};
+
+enum xrtErrorClass {
+  XRT_ERROR_CLASS_FIRST_ENTRY = 1,
+  XRT_ERROR_CLASS_SYSTEM = XRT_ERROR_CLASS_FIRST_ENTRY,
+  XRT_ERROR_CLASS_AIE,
+  XRT_ERROR_CLASS_HARDWARE,
+  XRT_ERROR_CLASS_UNKNOWN,
+  XRT_ERROR_CLASS_LAST_ENTRY = XRT_ERROR_CLASS_UNKNOWN
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xrt_mem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xrt_mem.h
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2019, Xilinx Inc - All rights reserved.
+ * Xilinx Runtime (XRT) APIs
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"). You may
+ * not use this file except in compliance with the License. A copy of the
+ * License is located at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ */
+
+#ifndef _XRT_MEM_H_
+#define _XRT_MEM_H_
+
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * XCL BO Flags bits layout
+ *
+ * bits  0 ~ 15: DDR BANK index
+ * bits 24 ~ 31: BO flags
+ */
+#define XRT_BO_FLAGS_MEMIDX_MASK	(0xFFFFFFUL)
+#define	XCL_BO_FLAGS_NONE		(0)
+#define	XCL_BO_FLAGS_CACHEABLE		(1U << 24)
+#define	XCL_BO_FLAGS_KERNBUF		(1U << 25)
+#define	XCL_BO_FLAGS_SGL		(1U << 26)
+#define	XCL_BO_FLAGS_SVM		(1U << 27)
+#define	XCL_BO_FLAGS_DEV_ONLY		(1U << 28)
+#define	XCL_BO_FLAGS_HOST_ONLY		(1U << 29)
+#define	XCL_BO_FLAGS_P2P		(1U << 30)
+#define	XCL_BO_FLAGS_EXECBUF		(1U << 31)
+
+/**
+ * XRT Native BO flags
+ *
+ * These flags are simple aliases for use with XRT native BO APIs.
+ */
+#define XRT_BO_FLAGS_NONE      XCL_BO_FLAGS_NONE
+#define XRT_BO_FLAGS_CACHEABLE XCL_BO_FLAGS_CACHEABLE
+#define XRT_BO_FLAGS_DEV_ONLY  XCL_BO_FLAGS_DEV_ONLY
+#define XRT_BO_FLAGS_HOST_ONLY XCL_BO_FLAGS_HOST_ONLY
+#define XRT_BO_FLAGS_P2P       XCL_BO_FLAGS_P2P
+#define XRT_BO_FLAGS_SVM       XCL_BO_FLAGS_SVM
+
+/**
+ * This is the legacy usage of XCL DDR Flags.
+ *
+ * byte-0 lower 4 bits for DDR Flags are one-hot encoded
+ */
+enum xclDDRFlags {
+    XCL_DEVICE_RAM_BANK0 = 0x00000000,
+    XCL_DEVICE_RAM_BANK1 = 0x00000002,
+    XCL_DEVICE_RAM_BANK2 = 0x00000004,
+    XCL_DEVICE_RAM_BANK3 = 0x00000008,
+};
+
+#ifdef __cplusplus
+}
+#endif
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/xrt_xclbin.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/xrt_xclbin.h
@@ -0,0 +1,80 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Xilinx Kernel Driver XCLBIN parser
+ *
+ * Copyright (C) 2020-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Authors: David Zhang <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XRT_XCLBIN_H
+#define _XRT_XCLBIN_H
+
+#include <linux/types.h>
+
+/* Used for parsing bitstream header */
+#define XHI_EVEN_MAGIC_BYTE     0x0f
+#define XHI_ODD_MAGIC_BYTE      0xf0
+
+/* Extra mode for IDLE */
+#define XHI_OP_IDLE  -1
+#define XHI_BIT_HEADER_FAILURE -1
+
+/* The imaginary module length register */
+#define XHI_MLR                  15
+
+#define DMA_HWICAP_BITFILE_BUFFER_SIZE 1024
+
+enum axlf_section_kind;
+struct axlf_section_header;
+struct axlf;
+
+/**
+ * Bitstream header information.
+ */
+struct XHwIcap_Bit_Header {
+	unsigned int HeaderLength;     /* Length of header in 32 bit words */
+	unsigned int BitstreamLength;  /* Length of bitstream to read in bytes*/
+	unsigned char *DesignName;     /* Design name get from bitstream */
+	unsigned char *PartName;       /* Part name read from bitstream */
+	unsigned char *Date;           /* Date read from bitstream header */
+	unsigned char *Time;           /* Bitstream creation time*/
+	unsigned int MagicLength;      /* Length of the magic numbers*/
+};
+
+int
+xrt_xclbin_parse_header(const unsigned char *data,
+	unsigned int size, struct XHwIcap_Bit_Header *header);
+
+void
+xrt_xclbin_free_header(struct XHwIcap_Bit_Header *header);
+
+char *
+xrt_xclbin_kind_to_string(enum axlf_section_kind kind);
+
+const struct axlf_section_header *
+xrt_xclbin_get_section_hdr(const struct axlf *xclbin, enum axlf_section_kind kind);
+
+int
+xrt_xclbin_check_section_hdr(const struct axlf_section_header *header,
+	uint64_t xclbin_len);
+
+int
+xrt_xclbin_section_info(const struct axlf *xclbin, enum axlf_section_kind kind,
+	uint64_t *offset, uint64_t *size);
+
+int
+xrt_xclbin_get_section(const struct axlf *xclbin,
+	enum axlf_section_kind kind, void **data, uint64_t *len);
+
+struct axlf_section_header *
+xrt_xclbin_get_section_hdr_next(const struct axlf *xclbin,
+	enum axlf_section_kind kind, struct axlf_section_header *cur);
+
+int xrt_xclbin_get_section_num(const struct axlf *xclbin,
+	enum axlf_section_kind kind);
+
+#endif /* _XRT_XCLBIN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_aie.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_aie.h
@@ -0,0 +1,158 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu <yliu@xilinx.com>
+ *    Himanshu Choudhary <hchoudha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_AIE_H_
+#define _ZOCL_AIE_H_
+
+#include "zynq_ioctl.h"
+
+/* Wait 100 * 1 ms before AIE parition is availabe after reset */
+#define	ZOCL_AIE_RESET_TIMEOUT_INTERVAL	1
+#define	ZOCL_AIE_RESET_TIMEOUT_NUMBER	100
+
+#define	ZOCL_AIE_ERROR_CACHE_CAP	8
+
+struct aie_work_data {
+	struct work_struct work;
+	struct drm_zocl_dev *zdev;
+};
+
+struct aie_error_cache {
+	u32			num;		/* Cached error # */
+	u32			cap;		/* Cache capacity */
+	struct aie_error	*errors;	/* Error array */
+};
+
+struct zocl_aie {
+	struct device	*aie_dev;	/* AI engine partition device */
+	u32		partition_id;	/* Partition ID */
+	u32		uid;		/* Imiage identifier loaded */
+	u32		fd_cnt;		/* # of fd requested */
+	bool		aie_reset;	/* If AIE is reset */
+
+	struct aie_error_cache	err;	/* AIE error cache */
+	struct workqueue_struct *wq;	/* AIE work queue */
+};
+
+struct zocl_graph_ctx_node {
+	struct list_head	link;
+	u32			ctx_code;
+	u32			gid;
+};
+
+#ifdef __NONE_PETALINUX__
+
+#define AIE_ERROR_CATEGORY_SATURATION		0U
+#define AIE_ERROR_CATEGORY_FP			1U
+#define AIE_ERROR_CATEGORY_STREAM		2U
+#define AIE_ERROR_CATEGORY_ACCESS		3U
+#define AIE_ERROR_CATEGORY_BUS			4U
+#define AIE_ERROR_CATEGORY_INSTRUCTION		5U
+#define AIE_ERROR_CATEGORY_ECC			6U
+#define AIE_ERROR_CATEGORY_LOCK			7U
+#define AIE_ERROR_CATEGORY_DMA			8U
+#define AIE_ERROR_CATEGORY_MEM_PARITY		9U
+
+enum aie_module_type {
+	AIE_MEM_MOD,
+	AIE_CORE_MOD,
+	AIE_PL_MOD,
+	AIE_NOC_MOD,
+};
+
+struct aie_location {
+	__u32 col;
+	__u32 row;
+};
+
+struct aie_partition_req {
+	__u32 partition_id;
+	__u32 uid;
+	__u64 meta_data;
+	__u32 flag;
+};
+
+struct aie_error {
+	struct aie_location loc;
+	enum aie_module_type module;
+	u32 error_id;
+	u32 category;
+};
+
+struct aie_errors {
+	struct device *dev;
+	struct aie_error *errors;
+	u32 num_err;
+};
+
+static inline struct device *
+aie_partition_request(struct aie_partition_req *req)
+{
+	return NULL;
+}
+
+static inline int
+aie_partition_get_fd(struct device *aie_dev)
+{
+	return -EINVAL;
+
+}
+
+static inline void aie_partition_release(struct device *dev) {}
+
+static inline bool
+aie_partition_is_available(struct aie_partition_req *req)
+{
+	return false;
+}
+
+static inline int
+aie_register_error_notification(struct device *dev, void (*cb)(void *priv),
+		void *priv)
+{
+	return -1;
+}
+
+static inline struct aie_errors *
+aie_get_errors(struct device *dev)
+{
+	return NULL;
+}
+
+static inline void
+aie_free_errors(struct aie_errors *aie_errs)
+{
+}
+#endif
+
+struct aie_info {
+	struct list_head	aie_cmd_list;
+	struct mutex		aie_lock;
+	struct aie_info_cmd	*cmd_inprogress;
+	wait_queue_head_t	aie_wait_queue;
+};
+
+struct aie_info_packet {
+	enum aie_info_code	opcode;
+	uint32_t		size;
+	char			info[AIE_INFO_SIZE];
+};
+
+struct aie_info_cmd {
+	struct list_head	aiec_list;
+	struct semaphore	aiec_sem;
+	struct aie_info_packet	*aiec_packet;
+};
+
+int zocl_init_aie(struct drm_zocl_dev *zdev);
+
+#endif /* _ZOCL_AIE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_bo.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_bo.h
@@ -0,0 +1,76 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu    <yliu@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_BO_H
+#define _ZOCL_BO_H
+
+#include "xclhal2_mem.h"
+
+/**
+ * XCL BO Flags bits layout
+ *
+ * bits  0 ~ 15: DDR BANK index
+ * bits 16 ~ 31: BO flags
+ *
+ * TODO These flags are copied from old xclhal2_mem.h. BO flags
+ * in current xclhal2_mem.h are modified. To prevent zocl from
+ * being broken, we keep a copy of old flags and implement a
+ * converter from the new flags to these old ones. These flags
+ * will be removed when we implement BO BO BO project at edge
+ * side.
+ */
+#define ZOCL_BO_FLAGS_CACHEABLE		(1 << 24)
+#define ZOCL_BO_FLAGS_HOST_BO		(1 << 25)
+#define ZOCL_BO_FLAGS_COHERENT		(1 << 26)
+#define ZOCL_BO_FLAGS_SVM		(1 << 27)
+#define ZOCL_BO_FLAGS_USERPTR		(1 << 28)
+#define ZOCL_BO_FLAGS_CMA		(1 << 29)
+#define ZOCL_BO_FLAGS_P2P		(1 << 30)
+#define ZOCL_BO_FLAGS_EXECBUF		(1 << 31)
+
+/* BO types we support */
+#define ZOCL_BO_NORMAL	(XRT_DRV_BO_HOST_MEM | XRT_DRM_SHMEM | \
+			XRT_DRV_BO_DRM_ALLOC)
+#define ZOCL_BO_EXECBUF	(ZOCL_BO_NORMAL)
+#define ZOCL_BO_CACHE	(ZOCL_BO_NORMAL | XRT_CACHEABLE)
+#define ZOCL_BO_USERPTR	(XRT_USER_MEM | XRT_DRV_BO_USER_ALLOC)
+#define ZOCL_BO_SVM	(XRT_DRV_BO_HOST_MEM | XRT_DRM_SHMEM | \
+			XRT_DRV_BO_DRM_ALLOC)
+#define ZOCL_BO_PL_DDR	(XRT_DEVICE_MEM)
+#define ZOCL_BO_HOST_BO	(XRT_DRV_BO_HOST_MEM)
+#define ZOCL_BO_IMPORT	(XRT_DRM_IMPORT | XRT_DRV_BO_HOST_MEM)
+
+static inline uint32_t zocl_convert_bo_uflags(uint32_t uflags)
+{
+	uint32_t zflags = 0;
+
+	/*
+	 * Keep the bank index and remove all flags, except EXECBUF and
+	 * CACHEABLE.
+	 */
+	if (uflags & XCL_BO_FLAGS_EXECBUF)
+		zflags |= ZOCL_BO_FLAGS_EXECBUF;
+
+	if (uflags & XCL_BO_FLAGS_CACHEABLE)
+		zflags |= ZOCL_BO_FLAGS_CACHEABLE;
+
+	zflags |= (uflags & 0xFFFF);
+
+	return zflags;
+}
+
+struct drm_gem_object *
+zocl_gem_import(struct drm_device *dev, struct dma_buf *dma_buf);
+
+#endif /* _ZOCL_BO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_cu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_cu.h
@@ -0,0 +1,187 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Compute unit structures.
+ *
+ * Copyright (C) 2019-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_CU_H_
+#define _ZOCL_CU_H_
+
+#include <linux/types.h>
+
+#include "zocl_util.h"
+
+#define U32_MASK 0xFFFFFFFF
+
+#define ZOCL_KDS_MASK		(~0xFF)
+#define ZOCL_CU_FREE_RUNNING	(U32_MASK & ZOCL_KDS_MASK)
+
+#define CU_INTR_DONE  0x1
+#define CU_INTR_READY 0x2
+
+#define CU_VERSION_MASK         0x00000F00
+#define CU_MAX_CAP_MASK         0x0000F000
+#define CU_READY_CNT_MASK       0x00FF0000
+#define CU_DONE_CNT_MASK        0xFF000000
+
+#define CU_AP_START	(0x1 << 0)
+#define CU_AP_DONE	(0x1 << 1)
+#define CU_AP_IDLE	(0x1 << 2)
+#define CU_AP_READY	(0x1 << 3)
+#define CU_AP_CONTINUE	(0x1 << 4)
+#define CU_AP_RESET	(0x1 << 5)
+
+struct zocl_cu;
+
+/* Supported CU models */
+enum zcu_model {
+	MODEL_ACC,
+	MODEL_HLS,
+};
+
+enum zcu_configure_type {
+	PAIRS,
+	CONSECUTIVE,
+};
+
+struct zcu_tasks_info {
+	u32	num_tasks_done;
+	u32	num_tasks_ready;
+};
+
+struct zcu_core {
+	phys_addr_t		 paddr;
+	u32 __iomem		*vaddr;
+	u32			 max_credits;
+	u32			 credits;
+	u32			 intr_type;
+	u32			 pending_intr;
+	u32			 running;
+	u32			 control;
+};
+
+struct zcu_funcs {
+	/**
+	 * @get_credit:
+	 *
+	 * Try to get one credit from the CU. A credit is required before
+	 * submit a task to the CU. Otherwise, it would lead to unknown CU
+	 * behaviour.
+	 * Return: the number of remaining credit.
+	 */
+	int (*get_credit)(void *core);
+
+	/**
+	 * @refund_credit:
+	 *
+	 * refund credit to the CU.
+	 */
+	void (*refund_credit)(void *core, u32 count);
+
+	/**
+	 * @configure:
+	 *
+	 * Congifure CU registers. It supports two types of configuration
+	 * format.
+	 *
+	 * 1. CONSECUTIVE: Which is a blind copy from data to CU.
+	 * 2. PAIRS: The data contains {addr, val} pairs.
+	 */
+	void (*configure)(void *core, u32 *data, size_t sz, int type);
+
+	/**
+	 * @start:
+	 *
+	 * Start a CU.
+	 */
+	void (*start)(void *core);
+
+	/**
+	 * @check:
+	 *
+	 * Check CU status and the pending task status.
+	 */
+	void (*check)(void *core, struct zcu_tasks_info *tasks);
+
+	/**
+	 * @reset:
+	 *
+	 * Reset CU.
+	 */
+	void (*reset)(void *core);
+
+	/**
+	 * @reset_done:
+	 *
+	 * Check if CU is properly reset
+	 */
+	int (*reset_done)(void *core);
+
+	/**
+	 * @enable_intr:
+	 *
+	 * Enable interrupt. Support DONE and READY interrupt.
+	 */
+	void (*enable_intr)(void *core, u32 intr_type);
+
+	/**
+	 * @disable_intr:
+	 *
+	 * Disable interrupt.
+	 */
+	void (*disable_intr)(void *core, u32 intr_type);
+
+	/**
+	 * @clear_intr:
+	 *
+	 * Clear interrupt.
+	 */
+	u32 (*clear_intr)(void *core);
+};
+
+struct zocl_cu {
+	enum zcu_model	          model;
+	struct list_head	  running_queue;
+	void                     *core;
+	u32			  usage;
+	u32			  done_cnt;
+	u32			  ready_cnt;
+	u32                       run_timeout;
+	u32                       reset_timeout;
+	u32			  irq;
+	char			 *irq_name;
+	/**
+	 * @funcs:
+	 *
+	 * Compute unit functions. Use these functions for operating the CU.
+	 */
+	struct zcu_funcs          *funcs;
+};
+
+int zocl_cu_init(struct zocl_cu *cu, enum zcu_model m, phys_addr_t paddr);
+int zocl_cu_fini(struct zocl_cu *cu);
+
+int  zocl_cu_get_credit(struct zocl_cu *cu);
+void zocl_cu_refund_credit(struct zocl_cu *cu, u32 count);
+void zocl_cu_configure(struct zocl_cu *cu, u32 *data, size_t sz, int type);
+void zocl_cu_start(struct zocl_cu *cu);
+void zocl_cu_check(struct zocl_cu *cu);
+void zocl_cu_reset(struct zocl_cu *cu);
+int  zocl_cu_reset_done(struct zocl_cu *cu);
+void zocl_cu_enable_intr(struct zocl_cu *cu, u32 intr_type);
+void zocl_cu_disable_intr(struct zocl_cu *cu, u32 intr_type);
+u32  zocl_cu_clear_intr(struct zocl_cu *cu);
+
+phys_addr_t zocl_cu_get_paddr(struct zocl_cu *cu);
+void zocl_cu_status_print(struct zocl_cu *cu);
+int zocl_cu_status_get(struct zocl_cu *cu);
+u32 zocl_cu_get_control(struct zocl_cu *cu);
+
+#endif /* _ZOCL_CU_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_cu_xgq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_cu_xgq.h
@@ -0,0 +1,41 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_CU_XGQ_H_
+#define _ZOCL_CU_XGQ_H_
+
+#include <linux/platform_device.h>
+
+#define CU_XGQ_DEV_NAME		"ZOCL_CU_XGQ"
+
+/*
+ * Resources for one cu xgq device.
+ */
+/* XGQ IP reg. Use in-mem version, if not provided. */
+#define	ZCX_RES_XGQ_IP		"ZOCL_CU_XGQ_IP"
+/* Reg to trigger interrupt to peer. Use prod/con pointer regs, if not provided. */
+#define	ZCX_RES_CQ_PROD_INT	"ZOCL_CU_XGQ_CQ_PRODUCER_INT"
+/* Shared ring buffer. */
+#define	ZCX_RES_RING		"ZOCL_CU_XGQ_RING"
+/* IRQ for incoming interrupt. */
+#define	ZCX_RES_IRQ		"ZOCL_CU_XGQ_IRQ"
+
+/* Platform data structure. */
+struct zocl_cu_xgq_info {
+	size_t zcxi_slot_size;
+	bool zcxi_echo_mode;
+	struct platform_device *zcxi_intc_pdev;
+};
+
+int zcu_xgq_assign_cu(struct platform_device *pdev, u32 cu_idx, u32 cu_domain);
+int zcu_xgq_unassign_cu(struct platform_device *pdev, u32 cu_idx, u32 cu_domain);
+
+#endif /* _ZOCL_CU_XGQ_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_dma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_dma.h
@@ -0,0 +1,78 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *    Jan Stephan  <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+
+/**
+ * DOC: Embedded driver handler interface for DMA
+ *
+ * Internal interfaces designed for interacting with Embedded Linux DMA Engine.
+ */
+#ifndef _ZOCL_DMA_H_
+#define _ZOCL_DMA_H_
+
+#define ZOCL_DMA_DONE	(1 << 0)
+#define ZOCL_DMA_ERROR	(1 << 1)
+
+typedef void (*zocl_dma_complete_cb)(void *arg, int ret);
+
+/**
+ * struct zocl_dma_handle - DMA handler for zocl driver
+ *
+ * @dma_flags: indicate if DMA returns error
+ * @dma_chan: DMA Channel, acquired before use DMA
+ * @dma_cookie: DMA Engine cookie
+ * @dma_done: DMA completion opaque
+ * @dma_func: call back function when dma complete
+ * @dma_arg: private data for dma_func call back function
+ *
+ * Prior to pass this handler to ZOCL DMA Engine, user can set dma_func and
+ * dma_arg for handling subsequent asynchronous operations. When DMA is
+ * completed the dma_func will be called with dma_arg. DMA error is returned
+ * via zocl_dma_complete_cb argument ret.
+ */
+typedef struct zocl_dma_handle {
+	int			dma_flags;
+	struct dma_chan		*dma_chan;
+	dma_cookie_t		dma_cookie;
+	struct completion	dma_done;
+	zocl_dma_complete_cb	dma_func;
+	void			*dma_arg;
+} zocl_dma_handle_t;
+
+/**
+ * zocl_dma_memcpy_pre() - DMA memory copy preparation.
+ *
+ * @dma_handle: zocl dma handler
+ * @dst_paddr: destination dma address
+ * @src_paddr: source dma address
+ * @size: number of bytes to read from source
+ */
+int zocl_dma_memcpy_pre(zocl_dma_handle_t *dma_handle, dma_addr_t dst_paddr,
+			dma_addr_t src_paddr, size_t size);
+
+/**
+ * zocl_dma_start() - Start DMA Engine.
+ *
+ * @dma_handle: zocl dma handler
+ *
+ * Common API for starting async DMA Engine. Current ZOCL DMA Engine only
+ * support memcpy, it can be enhanced for other type of DMAs when necessary.
+ */
+void zocl_dma_start(zocl_dma_handle_t *dma_handle);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_drv.h
@@ -0,0 +1,335 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *    Jan Stephan  <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_DRV_H_
+#define _ZOCL_DRV_H_
+#include <drm/drm.h>
+#include <drm/drm_device.h>
+#include <drm/drm_drv.h>
+#include <drm/drm_gem.h>
+#include <drm/drm_mm.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <linux/version.h>
+#include <linux/poll.h>
+#include "zocl_util.h"
+#include "zocl_ioctl.h"
+#include "zocl_ert.h"
+#include "zocl_bo.h"
+#include "zocl_dma.h"
+#include "zocl_ospi_versal.h"
+#include "zocl_watchdog.h"
+#include "xrt_cu.h"
+
+#if defined(CONFIG_ARM64)
+#define ZOCL_PLATFORM_ARM64   1
+#else
+#define ZOCL_PLATFORM_ARM64   0
+#endif
+
+/* Ensure compatibility with newer kernels and backported Red Hat kernels. */
+/* The y2k38 bug fix was introduced with Kernel 3.17 and backported to Red Hat
+ * 7.2.
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 17, 0)
+	#define ZOCL_TIMESPEC struct timespec64
+	#define ZOCL_GETTIME ktime_get_real_ts64
+	#define ZOCL_USEC tv_nsec / NSEC_PER_USEC
+#elif defined(RHEL_RELEASE_CODE)
+	#if RHEL_RELEASE_CODE >= RHEL_RELEASE_VERSION(7, 2)
+		#define ZOCL_TIMESPEC struct timespec64
+		#define ZOCL_GETTIME ktime_get_real_ts64
+		#define ZOCL_USEC tv_nsec / NSEC_PER_USEC
+	#else
+		#define ZOCL_TIMESPEC struct timeval
+		#define ZOCL_GETTIME do_gettimeofday
+		#define ZOCL_USEC tv_usec
+	#endif
+#else
+	#define ZOCL_TIMESPEC struct timeval
+	#define ZOCL_GETTIME do_gettimeofday
+	#define ZOCL_USEC tv_usec
+#endif
+
+/* drm_gem_object_put_unlocked was introduced with Kernel 4.12 and backported to
+ * Red Hat 7.5
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 7, 0)
+	#define ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED drm_gem_object_put
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(4, 12, 0)
+	#define ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED drm_gem_object_put_unlocked
+#elif defined(RHEL_RELEASE_CODE)
+	#if RHEL_RELEASE_CODE >= RHEL_RELEASE_VERSION(7, 5)
+		#define ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED \
+			drm_gem_object_put_unlocked
+	#else
+		#define ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED \
+			drm_gem_object_unreference_unlocked
+	#endif
+#else
+	#define ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED \
+		drm_gem_object_unreference_unlocked
+#endif
+
+/* drm_dev_put was introduced with Kernel 4.15 and backported to Red Hat 7.6. */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 15, 0)
+	#define ZOCL_DRM_DEV_PUT drm_dev_put
+#elif defined(RHEL_RELEASE_CODE)
+	#if RHEL_RELEASE_CODE >= RHEL_RELEASE_VERSION(7, 6)
+		#define ZOCL_DRM_DEV_PUT drm_dev_put
+	#else
+		#define ZOCL_DRM_DEV_PUT drm_dev_unref
+	#endif
+#else
+	#define ZOCL_DRM_DEV_PUT drm_dev_unref
+#endif
+
+/* access_ok lost its first parameter with Linux 5.0. */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 0, 0)
+	#define ZOCL_ACCESS_OK(TYPE, ADDR, SIZE) access_ok(ADDR, SIZE)
+#else
+	#define ZOCL_ACCESS_OK(TYPE, ADDR, SIZE) access_ok(TYPE, ADDR, SIZE)
+#endif
+
+struct sched_client_ctx;
+
+struct drm_zocl_exec_metadata {
+	enum drm_zocl_execbuf_state state;
+	unsigned int                index;
+};
+
+struct zocl_drv_private {
+	void		       *ops;
+};
+
+struct drm_zocl_bo {
+	union {
+		struct drm_gem_cma_object       cma_base;
+		struct {
+			struct drm_gem_object         gem_base;
+			struct page                 **pages;
+			struct sg_table              *sgt;
+			void                         *vmapping;
+			uint64_t                      uaddr;
+		};
+	};
+	struct drm_mm_node            *mm_node;
+	struct drm_zocl_exec_metadata  metadata;
+	unsigned int                   mem_index;
+	uint32_t                       flags;
+	unsigned int                   user_flags;
+};
+
+struct drm_zocl_copy_bo {
+	uint32_t dst_handle;
+	uint32_t src_handle;
+	uint64_t size;
+	uint64_t dst_offset;
+	uint64_t src_offset;
+};
+
+static inline struct drm_gem_object *
+zocl_gem_object_lookup(struct drm_device *dev,
+		struct drm_file   *filp,
+		u32                handle)
+{
+	return drm_gem_object_lookup(filp, handle);
+}
+
+static inline struct
+drm_zocl_bo *to_zocl_bo(struct drm_gem_object *bo)
+{
+	return (struct drm_zocl_bo *) bo;
+}
+
+static inline bool
+zocl_bo_userptr(const struct drm_zocl_bo *bo)
+{
+	return (bo->flags & ZOCL_BO_FLAGS_USERPTR);
+}
+
+static inline bool
+zocl_bo_execbuf(const struct drm_zocl_bo *bo)
+{
+	return (bo->flags & ZOCL_BO_FLAGS_EXECBUF);
+}
+
+static inline struct kernel_info *
+zocl_query_kernel(struct drm_zocl_slot *slot, const char *name)
+{
+	struct kernel_info *kernel;
+	int off = 0;
+
+	while (off < slot->ksize) {
+		kernel = (struct kernel_info *)(slot->kernels + off);
+		if (!strcmp(kernel->name, name))
+			break;
+		off += sizeof(struct kernel_info);
+		off += sizeof(struct argument_info) * kernel->anums;
+	}
+
+	if (off < slot->ksize)
+		return kernel;
+
+	return NULL;
+}
+
+static inline int
+zocl_kds_add_cu(struct drm_zocl_dev *zdev, struct xrt_cu *xcu)
+{
+	return kds_add_cu(&zdev->kds, xcu);
+}
+
+static inline int
+zocl_kds_add_scu(struct drm_zocl_dev *zdev, struct xrt_cu *xcu)
+{
+	return kds_add_scu(&zdev->kds, xcu);
+}
+
+static inline int
+zocl_kds_del_cu(struct drm_zocl_dev *zdev, struct xrt_cu *xcu)
+{
+	return kds_del_cu(&zdev->kds, xcu);
+}
+
+static inline int
+zocl_kds_del_scu(struct drm_zocl_dev *zdev, struct xrt_cu *xcu)
+{
+	return kds_del_scu(&zdev->kds, xcu);
+}
+
+int zocl_copy_bo_async(struct drm_device *dev, struct drm_file *fipl,
+		zocl_dma_handle_t *handle, struct drm_zocl_copy_bo *bo);
+
+bool zocl_can_dma_performed(struct drm_device *dev, struct drm_file *filp,
+	struct drm_zocl_copy_bo *args, uint64_t *dst_paddr,
+	uint64_t *src_paddr);
+int zocl_dma_channel_instance(zocl_dma_handle_t *dma_handle,
+			      struct drm_zocl_dev *zdev);
+
+void zocl_describe(const struct drm_zocl_bo *obj);
+
+void zocl_free_userptr_bo(struct drm_gem_object *obj);
+void zocl_free_host_bo(struct drm_gem_object *obj);
+int zocl_iommu_map_bo(struct drm_device *dev, struct drm_zocl_bo *bo);
+int zocl_iommu_unmap_bo(struct drm_device *dev, struct drm_zocl_bo *bo);
+
+int zocl_init_sysfs(struct device *dev);
+void zocl_fini_sysfs(struct device *dev);
+void zocl_free_sections(struct drm_zocl_slot *slot);
+void zocl_free_bo(struct drm_gem_object *obj);
+void zocl_drm_free_bo(struct drm_zocl_bo *bo);
+struct drm_zocl_bo *zocl_drm_create_bo(struct drm_device *dev,
+		uint64_t unaligned_size, unsigned user_flags);
+void zocl_update_mem_stat(struct drm_zocl_dev *zdev, u64 size,
+		int count, uint32_t bank);
+void zocl_init_mem(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot);
+void zocl_clear_mem(struct drm_zocl_dev *zdev);
+void zocl_clear_mem_slot(struct drm_zocl_dev *zdev, u32 slot_idx);
+int zocl_create_aie(struct drm_zocl_dev *zdev, struct axlf *axlf,
+		void *aie_res, uint8_t hw_gen);
+void zocl_destroy_aie(struct drm_zocl_dev *zdev);
+int zocl_aie_request_part_fd(struct drm_zocl_dev *zdev, void *data);
+int zocl_aie_reset(struct drm_zocl_dev *zdev);
+int zocl_aie_freqscale(struct drm_zocl_dev *zdev, void *data);
+int zocl_aie_graph_alloc_context(struct drm_zocl_dev *dev, u32 gid,
+		u32 ctx_code, struct sched_client_ctx *client);
+int zocl_aie_graph_free_context(struct drm_zocl_dev *dev, u32 gid,
+		struct sched_client_ctx *client);
+void zocl_aie_graph_free_context_all(struct drm_zocl_dev *zdev,
+		struct sched_client_ctx *client);
+int zocl_aie_alloc_context(struct drm_zocl_dev *zdev, u32 ctx_code,
+		struct sched_client_ctx *client);
+int zocl_aie_free_context(struct drm_zocl_dev *zdev,
+		struct sched_client_ctx *client);
+int zocl_aie_kds_add_graph_context(struct drm_zocl_dev *zdev, u32 gid,
+	        u32 ctx_code, struct kds_client *client);
+int zocl_aie_kds_del_graph_context(struct drm_zocl_dev *zdev, u32 gid,
+	        struct kds_client *client);
+void zocl_aie_kds_del_graph_context_all(struct kds_client *client);
+int zocl_aie_kds_add_context(struct drm_zocl_dev *zdev, u32 ctx_code,
+	struct kds_client *client);
+int zocl_aie_kds_del_context(struct drm_zocl_dev *zdev,
+	struct kds_client *client);
+int zocl_add_context_kernel(struct drm_zocl_dev *zdev, void *client_hdl, u32 cu_idx, u32 flags, u32 cu_domain);
+int zocl_del_context_kernel(struct drm_zocl_dev *zdev, void *client_hdl, u32 cu_idx, u32 cu_domain);
+
+int zocl_inject_error(struct drm_zocl_dev *zdev, void *data,
+		struct drm_file *filp);
+int zocl_init_error(struct drm_zocl_dev *zdev);
+void zocl_fini_error(struct drm_zocl_dev *zdev);
+int zocl_insert_error_record(struct drm_zocl_dev *zdev, xrtErrorCode err_code);
+
+/* zocl_kds.c */
+int zocl_init_sched(struct drm_zocl_dev *zdev);
+void zocl_fini_sched(struct drm_zocl_dev *zdev);
+int zocl_create_client(struct device *dev, void **client_hdl);
+void zocl_destroy_client(void *client_hdl);
+uint zocl_poll_client(struct file *filp, poll_table *wait);
+int zocl_command_ioctl(struct drm_zocl_dev *zdev, void *data,
+		       struct drm_file *filp);
+int zocl_context_ioctl(struct drm_zocl_dev *zdev, void *data,
+		       struct drm_file *filp);
+struct platform_device *zocl_find_pdev(char *name);
+
+static inline struct drm_zocl_dev *
+zocl_get_zdev(void)
+{
+	struct platform_device *pdev = zocl_find_pdev("zyxclmm_drm");
+	if(!pdev)
+		return NULL;
+	return platform_get_drvdata(pdev);
+}
+int get_apt_index_by_addr(struct drm_zocl_dev *zdev, phys_addr_t addr);
+int get_apt_index_by_cu_idx(struct drm_zocl_dev *zdev, int cu_idx);
+void update_cu_idx_in_apt(struct drm_zocl_dev *zdev, int apt_idx, int cu_idx);
+
+int zocl_kds_reset(struct drm_zocl_dev *zdev);
+
+int subdev_create_cu(struct device *dev, struct xrt_cu_info *info, struct platform_device **pdevp);
+void subdev_destroy_cu(struct drm_zocl_dev *zdev);
+int subdev_create_scu(struct device *dev, struct xrt_cu_info *info, struct platform_device **pdevp);
+void subdev_destroy_scu(struct drm_zocl_dev *zdev);
+/* Sub device driver */
+extern struct platform_driver zocl_cu_xgq_driver;
+extern struct platform_driver zocl_csr_intc_driver;
+extern struct platform_driver zocl_xgq_intc_driver;
+extern struct platform_driver zocl_rpu_channel_driver;
+extern struct platform_driver cu_driver;
+extern struct platform_driver scu_driver;
+struct zocl_cu_ops {
+	int (*submit)(struct platform_device *pdev, struct kds_command *xcmd);
+};
+
+static inline int
+zocl_cu_submit_xcmd(struct drm_zocl_dev *zdev, int i, struct kds_command *xcmd)
+{
+	struct platform_device *pdev;
+	struct zocl_drv_private *priv;
+	struct zocl_cu_ops *ops;
+
+	pdev = zdev->cu_pldev[i];
+	priv = (void *)platform_get_device_id(pdev)->driver_data;
+	ops = (struct zocl_cu_ops *)priv->ops;
+	return ops->submit(pdev, xcmd);
+}
+
+extern u32 zocl_cu_get_status(struct platform_device *pdev);
+extern u32 zocl_scu_get_status(struct platform_device *pdev);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+extern const struct drm_gem_object_funcs zocl_gem_object_funcs;
+extern const struct drm_gem_object_funcs zocl_cma_default_funcs;
+#endif
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_error.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_error.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu    <yliu@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_ERROR_H
+#define _ZOCL_ERROR_H
+
+#include "xrt_error_code.h"
+
+#define	ZOCL_DEFAULT_ERROR_CAPACITY	8
+
+struct zocl_err_record {
+	xrtErrorCode	zer_err_code;	/* XRT error code */
+	u64		zer_ts;		/* timestamp */
+};
+
+struct zocl_error {
+	int		ze_num;		/* number of errors recorded */
+	int		ze_cap;		/* capacity of current error array */
+	struct zocl_err_record *ze_err;	/* error array pointer */
+};
+
+#endif /* _ZOCL_ERROR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_ert.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_ert.h
@@ -0,0 +1,201 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2016-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_ERT_H_
+#define _ZOCL_ERT_H_
+
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include "ert.h"
+
+/* DSA and/or Device tree related */
+#define ERT_IRQ_NUMBER 2
+#define ERT_CQ_IRQ     0
+#define ERT_CU_IRQ     1
+
+#define ZOCL_ERT_HW_RES     0
+#define ZOCL_ERT_CQ_RES     1
+
+/**
+ * Address constants per spec
+ */
+#define WORD_SIZE                     4          /* 4 bytes */
+#define CQ_SIZE                       0x10000    /* 64K */
+#define CQ_SLOT_SIZE                  0x1000     /* 4K each cq slot */
+#define CQ_BASE_ADDR                  0x190000
+#define CSR_ADDR                      0x180000
+
+#define CQ_SLOT_NUM	(CQ_SIZE / CQ_SLOT_SIZE)      /* defult cq slot num = 16 */
+
+/**
+ * The STATUS REGISTER is for communicating completed CQ slot indices
+ * MicroBlaze write, host reads.  MB(W) / HOST(COR)
+ */
+#define ERT_STATUS_REG          0x0
+#define ERT_STATUS_REG0         0x0
+#define ERT_STATUS_REG1         0x4
+#define ERT_STATUS_REG2         0x8
+#define ERT_STATUS_REG3         0xC
+
+/**
+ * The CU DMA REGISTER is for communicating which CQ slot is to be started
+ * on a specific CU.  MB selects a free CU on which the command can
+ * run, then writes the 1<<CU back to the command slot CU mask and
+ * writes the slot index to the CU DMA REGISTER.  HW is notified when
+ * the register is written and now does the DMA transfer of CU regmap
+ * map from command to CU, while MB continues its work. MB(W) / HW(R)
+ */
+#define ERT_CU_DMA_ENABLE       0x18
+#define ERT_CU_DMA_REG          0x1C
+#define ERT_CU_DMA_REG0         0x1C
+#define ERT_CU_DMA_REG1         0x20
+#define ERT_CU_DMA_REG2         0x24
+#define ERT_CU_DMA_REG3         0x28
+
+/**
+ * The SLOT SIZE is the size of slots in command queue, it is
+ * configurable per xclbin. MB(W) / HW(R)
+ */
+#define ERT_CQ_SLOT_SIZE_REG    0x2C
+
+/**
+ * The CU_OFFSET is the size of a CU's address map in power of 2.  For
+ * example a 64K regmap is 2^16 so 16 is written to the CU_OFFSET_ADDR.
+ * MB(W) / HW(R)
+ */
+#define ERT_CU_OFFSET_REG       0x30
+
+/**
+ * The number of slots is command_queue_size / slot_size.
+ * MB(W) / HW(R)
+ */
+#define ERT_CQ_NUM_OF_SLOTS_REG 0x34
+
+/**
+ * All CUs placed in same address space separated by CU_OFFSET. The
+ * CU_BASE_ADDRESS is the address of the first CU. MB(W) / HW(R)
+ */
+#define ERT_CU_BASE_ADDR_REG    0x38
+
+/**
+ * The CQ_BASE_ADDRESS is the base address of the command queue.
+ * MB(W) / HW(R)
+ */
+#define ERT_CQ_BASE_ADDR_REG    0x3C
+
+/**
+ * The CU_ISR_HANDLER_ENABLE (MB(W)/HW(R)) enables the HW handling of
+ * CU interrupts.  When a CU interrupts (when done), hardware handles
+ * the interrupt and writes the index of the CU that completed into
+ * the CU_STATUS_REGISTER (HW(W)/MB(COR)) as a bitmask
+ */
+#define ERT_CU_ISR_ENABLE       0x40
+#define ERT_CU_STATUS_REG       0x44
+#define ERT_CU_STATUS_REG0      0x44
+#define ERT_CU_STATUS_REG1      0x48
+#define ERT_CU_STATUS_REG2      0x4C
+#define ERT_CU_STATUS_REG3      0x50
+
+/**
+ * The CQ_STATUS_ENABLE (MB(W)/HW(R)) enables interrupts from HOST to
+ * MB to indicate the presense of a new command in some slot.  The
+ * slot index is written to the CQ_STATUS_REGISTER (HOST(W)/MB(R))
+ */
+#define ERT_CQ_STATUS_ENABLE    0x54
+#define ERT_CQ_STATUS_REG       0x58
+#define ERT_CQ_STATUS_REG0      0x58
+#define ERT_CQ_STATUS_REG1      0x5C
+#define ERT_CQ_STATUS_REG2      0x60
+#define ERT_CQ_STATUS_REG3      0x64
+
+/**
+ * The NUMBER_OF_CU (MB(W)/HW(R) is the number of CUs per current
+ * xclbin.  This is an optimization that allows HW to only check CU
+ * completion on actual CUs.
+ */
+#define ERT_NUM_OF_CU_REG       0x68
+
+/**
+ * Enable global interrupts from MB to HOST on command completion.
+ * When enabled writing to STATUS_REGISTER causes an interrupt in HOST.
+ * MB(W)
+ */
+#define ERT_HOST_INT_ENABLE     0x100
+
+/* ERT drive name */
+#define ZOCL_ERT_NAME "zocl_ert"
+
+extern struct platform_driver zocl_ert_driver;
+struct zocl_ert_ops;
+
+struct zocl_ert_dev {
+	struct platform_device       *pdev;
+	void __iomem                 *hw_ioremap;
+	void __iomem                 *cq_ioremap;
+	unsigned int                  irq[ERT_IRQ_NUMBER];
+	const struct zocl_ert_ops    *ops;
+};
+
+struct zocl_ert_ops {
+	/**
+	 * @init:
+	 *
+	 * Initial ERT dedicated FPGA module
+	 */
+	void (*init)(struct zocl_ert_dev *ert);
+	/**
+	 * @fini:
+	 *
+	 * Finish ERT dedicated FPGA module
+	 */
+	void (*fini)(struct zocl_ert_dev *ert);
+	/**
+	 * @config:
+	 *
+	 * Configure command could configure ERT dedicated module
+	 */
+	void (*config)(struct zocl_ert_dev *ert,
+		       struct ert_configure_cmd *cfg);
+	/**
+	 * @get_next_cmd:
+	 *
+	 * Return next cmd. If no command found, return NULL.
+	 */
+	struct ert_packet *
+	(*get_next_cmd)(struct zocl_ert_dev *ert,
+			struct ert_packet *pkg, int *idx_ret);
+	/**
+	 * @notify_host:
+	 *
+	 * Notify host the status of a command is changed.
+	 */
+	void (*notify_host)(struct zocl_ert_dev *ert, int slot_idx);
+
+	/**
+	 * @updata_cmd:
+	 *
+	 * Update the data section of a CQ slot
+	 */
+	void (*update_cmd)(struct zocl_ert_dev *ert, int idx,
+			    void *data, int sz);
+};
+
+struct zocl_ert_info {
+	int			model;
+	struct zocl_ert_ops    *ops;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_ert_intc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_ert_intc.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_ERT_INTC_H_
+#define _ZOCL_ERT_INTC_H_
+
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include "zocl_lib.h"
+
+#define ERT_CSR_INTC_DEV_NAME		"ZOCL_CSR_INTC"
+#define ERT_XGQ_INTC_DEV_NAME		"ZOCL_XGQ_INTC"
+
+/*
+ * Resources for one ERT INTC device.
+ */
+#define	ZEI_RES_IRQ		"ZOCL_ERT_INTC_IRQ"
+#define	ZEI_RES_STATUS		"ZOCL_ERT_INTC_STATUS"
+
+/* 5 registers for CU and CQ status resptectively. Max supported ID is 128. */
+struct zocl_ert_intc_status_reg {
+	u32		zeisr_enable;
+	u32		zeisr_status[4];
+};
+
+struct zocl_ert_intc_handler {
+	struct platform_device *zeih_pdev;
+	u32		zeih_irq;
+	irq_handler_t	zeih_cb;
+	void		*zeih_arg;
+	bool		zeih_enabled;
+};
+
+struct zocl_ert_intc_drv_data {
+	void (*add)(struct platform_device *pdev, u32 id, irq_handler_t handler, void *arg);
+	void (*remove)(struct platform_device *pdev, u32 id);
+	void (*config)(struct platform_device *pdev, u32 id, bool enabled);
+};
+
+#define	ERT_INTC_DRVDATA(pdev)	\
+	((struct zocl_ert_intc_drv_data *)platform_get_device_id(pdev)->driver_data)
+
+static inline void
+zocl_ert_intc_add(struct platform_device *pdev, u32 id, irq_handler_t cb, void *arg)
+{
+	ERT_INTC_DRVDATA(pdev)->add(pdev, id, cb, arg);
+}
+
+static inline void
+zocl_ert_intc_remove(struct platform_device *pdev, u32 id)
+{
+	ERT_INTC_DRVDATA(pdev)->remove(pdev, id);
+}
+
+static inline void zocl_ert_intc_config(struct platform_device *pdev, u32 id, bool enabled)
+{
+	ERT_INTC_DRVDATA(pdev)->config(pdev, id, enabled);
+}
+
+static inline int zocl_ert_create_intc(struct device *dev, u32 *irqs, size_t num_irqs,
+				       u64 status_reg, const char *dev_name,
+				       struct platform_device **pdevp)
+{
+	/* Total num of res is irqs + status reg. */
+	struct resource *res = kzalloc(sizeof(*res) * (num_irqs + 1), GFP_KERNEL);
+	int ret = 0;
+	size_t i = 0;
+
+	if (!res)
+		return -ENOMEM;
+
+	/* Fill in IRQ and status reg resources. */
+	for (i = 0; i < num_irqs; i++)
+		fill_irq_res(&res[i], irqs[i], ZEI_RES_IRQ);
+	fill_iomem_res(&res[i++], status_reg, sizeof(struct zocl_ert_intc_status_reg),
+		       ZEI_RES_STATUS);
+
+	ret = zlib_create_subdev(dev, dev_name, res, i, NULL, 0, pdevp);
+	kfree(res);
+
+	return ret;
+}
+
+static inline void zocl_ert_destroy_intc(struct platform_device *pdev)
+{
+	zlib_destroy_subdev(pdev);
+}
+
+#endif /* _ZOCL_ERT_INTC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_generic_cu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_generic_cu.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Generic compute unit structures.
+ *
+ * Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_GENERIC_CU_H_
+#define _ZOCL_GENERIC_CU_H_
+
+/* Bits in generic_cu_info.flag */
+#define GCU_IRQ_DISABLED 0
+
+struct generic_cu {
+	struct drm_zocl_dev	*zdev;
+	struct generic_cu_info	*info;
+	wait_queue_head_t	waitq;
+	atomic_t		event;
+	unsigned long		flag;
+	spinlock_t		lock;
+};
+
+struct generic_cu_info {
+	const char		*name;
+	int			cu_idx;
+	int                     irq;
+};
+
+int zocl_open_gcu(struct drm_zocl_dev *zdev, struct drm_zocl_ctx *ctx,
+		  struct sched_client_ctx *client);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_ioctl.h
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style CMA backed memory manager for ZynQ based OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _XCL_ZOCL_IOCTL_H_
+#define _XCL_ZOCL_IOCTL_H_
+
+#include "zynq_ioctl.h"
+
+int zocl_create_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_userptr_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_get_hbo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_sync_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_map_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_info_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_pwrite_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_pread_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_execbuf_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_read_axlf_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_sk_getcmd_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_sk_create_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_sk_report_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_info_cu_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_ctx_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_error_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_aie_fd_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_aie_reset_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_aie_getcmd_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_aie_putcmd_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+int zocl_aie_freqscale_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_lib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_lib.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2016-2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_LIB_H_
+#define _ZOCL_LIB_H_
+
+#include <linux/platform_device.h>
+
+#define zocl_err(dev, fmt, args...)	dev_err(dev, "%s: "fmt, __func__, ##args)
+#define zocl_info(dev, fmt, args...)	dev_info(dev, "%s: "fmt, __func__, ##args)
+#define zocl_dbg(dev, fmt, args...)	dev_dbg(dev, "%s: "fmt, __func__, ##args)
+
+void __iomem *zlib_map_res(struct device *dev, struct resource *res, u64 *startp, size_t *szp);
+void __iomem *zlib_map_res_by_id(struct platform_device *pdev, int id, u64 *startp, size_t *szp);
+void __iomem *zlib_map_res_by_name(struct platform_device *pdev,
+				   const char *name, u64 *startp, size_t *szp);
+void __iomem *zlib_map_phandle_res_by_name(struct platform_device *pdev,
+					   const char *name, u64 *startp, size_t *szp);
+int zlib_create_subdev(struct device *dev, const char *devname, struct resource *res, size_t nres,
+		       void *info, size_t info_size, struct platform_device **pdevp);
+void zlib_destroy_subdev(struct platform_device *pdev);
+
+static inline void fill_irq_res(struct resource *res, u32 irq, char *name)
+{
+	res->start = irq;
+	res->end = irq;
+	res->flags = IORESOURCE_IRQ;
+	res->name = name;
+}
+
+static inline void fill_iomem_res(struct resource *res, resource_size_t start,
+				  resource_size_t size, char *name)
+{
+	res->start = start;
+	res->end = start + size - 1;
+	res->flags = IORESOURCE_MEM;
+	res->name = name;
+}
+
+static inline void fill_reg_res(struct resource *res, resource_size_t start, char *name)
+{
+	fill_iomem_res(res, start, sizeof(u32), name);
+}
+
+#endif /* _ZOCL_LIB_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_mailbox.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_mailbox.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    David Zhang <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_MAILBOX_H_
+#define _ZOCL_MAILBOX_H_
+
+#define	MBX_STATUS_EMPTY	(1 << 0)
+#define	MBX_STATUS_FULL		(1 << 1)
+#define	MBX_STATUS_STA		(1 << 2)
+#define	MBX_STATUS_RTA		(1 << 3)
+
+/*
+ * Mailbox IP register layout
+ */
+struct mailbox_reg {
+	u32			mbr_wrdata;
+	u32			mbr_resv1;
+	u32			mbr_rddata;
+	u32			mbr_resv2;
+	u32			mbr_status;
+	u32			mbr_error;
+	u32			mbr_sit;
+	u32			mbr_rit;
+	u32			mbr_is;
+	u32			mbr_ie;
+	u32			mbr_ip;
+	u32			mbr_ctrl;
+} __packed;
+
+struct mailbox {
+	struct mailbox_reg	*mbx_regs;
+};
+
+u32 zocl_mailbox_status(struct mailbox *mbx);
+u32 zocl_mailbox_get(struct mailbox *mbx);
+void zocl_mailbox_set(struct mailbox *mbx, u32 val);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_ospi_versal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_ospi_versal.h
@@ -0,0 +1,64 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu <yliu@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_OSPI_VERSAL_H_
+#define	_ZOCL_OSPI_VERSAL_H_
+
+extern struct platform_driver zocl_ospi_versal_driver;
+
+struct zocl_ov_pkt_node {
+	size_t			zn_size;
+	u32			*zn_datap;
+	struct zocl_ov_pkt_node	*zn_next;
+};
+
+/**
+ * Main structure of ospi versal subdev.
+ * @timer_task:	main thread pointer
+ * @base:	PDI packet area base address
+ * @size:	PDI packet area size
+ * @pdi_ready:	flag to indicate PDI image is ready
+ * @pdi_done:	flag to indicate PDI flashing is done
+ * @pdev:	platform_device
+ * @head:	head node of PDI packet linked list
+ */
+struct zocl_ov_dev {
+	struct task_struct	*timer_task;
+	void __iomem		*base;
+	size_t			size;
+	u8			pdi_ready;
+	u8			pdi_done;
+	rwlock_t		att_rwlock;
+
+	/* platform device */
+	struct platform_device  *pdev;
+
+	/* parent platform device */
+	struct platform_device	*ppdev;
+
+	struct zocl_ov_pkt_node	*head;
+};
+
+/* Timer thread wake up interval in Millisecond */
+#define	ZOCL_OV_TIMER_INTERVAL		(1000)
+
+#define	ZOCL_OSPI_VERSAL_BRAM_RES	0
+
+/* OSPI VERSAL driver name */
+#define	ZOCL_OSPI_VERSAL_NAME "zocl_ospi_versal"
+
+int zocl_ov_init_sysfs(struct device *dev);
+void zocl_ov_fini_sysfs(struct device *dev);
+
+#endif /* _ZOCL_OSPI_VERSAL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_sk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_sk.h
@@ -0,0 +1,97 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu <yliu@xilinx.com>
+ *    Jeff Lin  <jeffli@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_SK_H_
+#define _ZOCL_SK_H_
+
+#include "ps_kernel.h"
+
+#define	MAX_SOFT_KERNEL		128
+
+#define	ZOCL_SCU_FLAGS_RELEASE	1
+
+#define SK_CRASHED		-1
+#define SK_ERROR		-2
+#define SK_NOTEXIST		-3
+#define SK_DONE			1
+#define SK_RUNNING		2
+
+struct soft_cu {
+	void			*sc_vregs;
+	struct drm_gem_object	*gem_obj;
+
+	/*
+	 * This semaphore is used for each soft kernel
+	 * CU to wait for next command. When new command
+	 * for this CU comes in or we are told to abort
+	 * a CU, ert will up this semaphore.
+	 */
+	struct semaphore	sc_sem;
+
+	uint32_t		sc_flags;
+	uint64_t		usage;
+
+	/*
+	 * soft cu pid and parent pid. This can be used to identify if the
+	 * soft cu is still running or not. The parent should never crash
+	 */
+	uint32_t		sc_pid;
+	uint32_t		sc_parent_pid;
+};
+
+struct scu_image {
+	uint32_t		si_start;	/* start instance # */
+	uint32_t		si_end;		/* end instance # */
+	int			si_bohdl;	/* BO handle */
+	struct drm_zocl_bo	*si_bo;		/* BO to hold the image */
+	char		        scu_name[PS_KERNEL_NAME_LENGTH];	/* Soft Kernel Name */
+};
+
+struct soft_krnl {
+	struct list_head	sk_cmd_list;
+	struct mutex		sk_lock;
+	struct soft_cu		*sk_cu[MAX_SOFT_KERNEL];
+
+	/*
+	 * sk_ncus is a counter represents how many
+	 * compute units are configured.
+	 */
+	uint32_t		sk_ncus;
+
+	int			sk_meta_bohdl;	/* metadata BO handle */
+	struct drm_zocl_bo	*sk_meta_bo;		/* BO to hold metadata */
+	uint32_t		sk_nimg;
+	struct scu_image	*sk_img;
+	wait_queue_head_t	sk_wait_queue;
+};
+
+struct soft_krnl_cmd {
+	struct list_head	skc_list;
+	uint32_t		skc_opcode;
+	struct config_sk_image_uuid	*skc_packet;
+};
+
+int zocl_init_soft_kernel(struct drm_zocl_dev *zdev);
+void zocl_fini_soft_kernel(struct drm_zocl_dev *zdev);
+extern struct platform_device *zert_get_scu_pdev(struct platform_device *pdev, u32 cu_idx);
+extern int zocl_scu_create_sk(struct platform_device *pdev, u32 pid, u32 parent_pid, struct drm_file *filp, int *boHandle);
+extern int zocl_scu_wait_cmd_sk(struct platform_device *pdev);
+extern int zocl_scu_wait_ready(struct platform_device *pdev);
+extern void zocl_scu_sk_ready(struct platform_device *pdev);
+extern void zocl_scu_sk_crash(struct platform_device *pdev);
+extern void zocl_scu_sk_shutdown(struct platform_device *pdev);
+extern void zocl_scu_sk_fini(struct platform_device *pdev);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_util.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_util.h
@@ -0,0 +1,178 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_UTIL_H_
+#define _ZOCL_UTIL_H_
+
+#include "zocl_lib.h"
+#include "kds_core.h"
+#include "zocl_error.h"
+#include "zynq_ioctl.h"
+
+#define _4KB	0x1000
+#define _8KB	0x2000
+#define _64KB	0x10000
+
+#define MAX_PR_SLOT_NUM	32
+#define MAX_CU_NUM     128
+/* Apertures contains both ip and debug ip information */
+#define MAX_APT_NUM		2*MAX_CU_NUM
+#define EMPTY_APT_VALUE		((phys_addr_t) -1)
+#define CU_SIZE        _64KB
+#define PR_ISO_SIZE    _4KB
+
+#define CLEAR(x) \
+	memset(&x, 0, sizeof(x))
+
+#define sizeof_section(sect, data) \
+({ \
+	size_t ret; \
+	size_t data_size; \
+	data_size = sect->m_count * sizeof(typeof(sect->data)); \
+	ret = (sect) ? offsetof(typeof(*sect), data) + data_size : 0; \
+	(ret); \
+})
+
+/*
+ * Get the bank index from BO creation flags.
+ * bits  0 ~ 15: DDR BANK index
+ */
+#define MEM_BANK_SHIFT_BIT	11
+#define	GET_MEM_INDEX(x)	((x) & 0xFFFF)
+#define	GET_SLOT_INDEX(x)	(((x) >> MEM_BANK_SHIFT_BIT) & 0x7FF)
+#define SET_MEM_INDEX(x, y)	(((x) << MEM_BANK_SHIFT_BIT) | y)
+
+#define ZOCL_GET_ZDEV(ddev) (ddev->dev_private)
+
+struct drm_zocl_mm_stat {
+	size_t memory_usage;
+	unsigned int bo_count;
+};
+
+struct addr_aperture {
+	phys_addr_t	addr;
+	size_t		size;
+	u32		prop;
+	int		cu_idx;
+	u32		slot_idx;
+};
+
+enum zocl_mem_type {
+	ZOCL_MEM_TYPE_CMA		= 0,
+	ZOCL_MEM_TYPE_RANGE_ALLOC	= 1,
+	ZOCL_MEM_TYPE_STREAMING		= 2,
+};
+
+/*
+ * Memory structure in zocl driver. There will be an array of this
+ * structure where each element is representing each section in
+ * the memory topology in xclbin.
+ */
+struct zocl_mem {
+	u32			zm_mem_idx;
+	enum zocl_mem_type	zm_type;
+	unsigned int		zm_used;
+	u64			zm_base_addr;
+	u64			zm_size;
+	struct drm_zocl_mm_stat zm_stat;
+	struct list_head	link;
+	struct list_head        zm_list;
+};
+
+/*
+ * zocl dev specific data info, if there are different configs across
+ * different compitible device, add their specific data here.
+ */
+struct zdev_data {
+	char fpga_driver_name[64];
+};
+
+struct aie_metadata {
+	size_t size;
+	void *data;
+};
+
+struct drm_zocl_slot {
+	u32			 slot_idx;
+	struct mem_topology	*topology;
+	struct ip_layout	*ip;
+	struct debug_ip_layout	*debug_ip;
+	struct connectivity	*connectivity;
+	struct axlf             *axlf;
+	size_t                   axlf_size;
+	struct aie_metadata	 aie_data;
+
+	u64			 pr_isolation_addr;
+	u16			 pr_isolation_freeze;
+	u16			 pr_isolation_unfreeze;
+	int			 partial_overlay_id;
+
+	int			 ksize;
+	char			*kernels;
+
+	struct zocl_xclbin	*slot_xclbin;
+	struct mutex		 slot_xclbin_lock;
+};
+
+struct drm_zocl_dev {
+	struct drm_device       *ddev;
+	struct fpga_manager     *fpga_mgr;
+	struct zocl_ert_dev     *ert;
+	struct iommu_domain	*domain;
+	phys_addr_t              host_mem;
+	resource_size_t          host_mem_len;
+	/* Record start address, this is only for MPSoC as PCIe platform */
+	phys_addr_t		 res_start;
+	unsigned int		 cu_num;
+	unsigned int             irq[MAX_CU_NUM];
+	struct sched_exec_core  *exec;
+	/* Zocl driver memory list head */
+	struct list_head	 zm_list_head;
+	struct drm_mm           *zm_drm_mm;    /* DRM MM node for PL-DDR */
+	struct mutex		 mm_lock;
+	struct mutex		 aie_lock;
+
+	struct list_head	 ctx_list;
+
+	struct addr_aperture	*apertures;
+	unsigned int		 num_apts;
+
+	struct kds_sched	 kds;
+	struct platform_device	*cu_pldev[MAX_CU_NUM];
+
+	/*
+	 * This RW lock is to protect the sysfs nodes exported
+	 * by zocl driver. Currently, all zocl attributes exported
+	 * to sysfs nodes are protected by a single lock. Any read
+	 * functions which not atomically touch those attributes should
+	 * hold read lock; And all write functions which not atomically
+	 * touch those attributes should hold write lock.
+	 */
+	rwlock_t		attr_rwlock;
+
+	struct soft_krnl	*soft_kernel;
+	struct aie_info		*aie_information;
+	struct dma_chan		*zdev_dma_chan;
+	struct mailbox		*zdev_mailbox;
+	const struct zdev_data	*zdev_data_info;
+	struct generic_cu	*generic_cu;
+	struct zocl_error	 zdev_error;
+	struct zocl_aie		*aie;
+	struct zocl_watchdog_dev *watchdog;
+
+	int			 num_pr_slot;
+	int			 full_overlay_id;
+	struct drm_zocl_slot	*pr_slot[MAX_PR_SLOT_NUM];
+};
+
+int zocl_kds_update(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot,
+		    struct drm_zocl_kds *cfg);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_watchdog.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_watchdog.h
@@ -0,0 +1,88 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_WATCHDOG_H_
+#define _ZOCL_WATCHDOG_H_
+
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+/* watchdog subdev driver name */
+#define ZOCL_WATCHDOG_NAME "zocl_watchdog"
+
+/*
+ * will the cmc process name change?
+ * or
+ * do we even need to monitor cmc?
+ */
+#define CMC "xilinx-cmc"
+
+/* check every 3s */
+#define ZOCL_WATCHDOG_FREQ (3000)
+
+/*
+ * register at ps_reset_controller offset 0xc, upper 16 bits
+ * are being used for the watchdog purpose
+ * 
+ * Among the 16 bits, the upper 8 bits are used as counter and the lower
+ * 8 bits are used to show the state of individual part.
+ *
+ * The counter will be increased by 1 every check and gone back to 1 once
+ * overflow. This happens only when each piece we are monitoring is healthy.
+ * a 0 in counter means nothing is being monitored, say during ps reboot
+ *
+ * The pieces we are monitoring so far include,
+ * skd,
+ * cmc,
+ * cq thread
+ * sched thread
+ *
+ * So far when zocl is running in ert mode, we don't support kds. If in future
+ * we do support kds, which means, we may not need sched thread and create
+ * per cu thread, and since the per cu thread is created when the xclbin is
+ * created, the watchdog thread may not know those thread before hand.
+ * In that case, we may need to introduce a list linking all threads being
+ * monitored -- the link itself can be dynamically changed.
+ */
+#define WATCHDOG_OFFSET		0xc
+#define COUNTER_MASK		0xff000000
+#define RESET_MASK		0xffff
+#define SKD_BIT_SHIFT		16
+#define CMC_BIT_SHIFT		17
+#define CQ_THD_BIT_SHIFT	18
+#define SCHED_THD_BIT_SHIFT	19
+#define COUNTER_BITS_SHIFT	24
+
+extern struct platform_driver zocl_watchdog_driver;
+struct zocl_watchdog_dev;
+
+struct watchdog_cfg {
+	bool skd_run;
+	bool cmc_run;
+	bool cq_thread_run;
+	bool sched_thread_run;
+};
+
+struct zocl_watchdog_ops {
+	void (*init)(struct zocl_watchdog_dev *watchdog);
+	void (*fini)(struct zocl_watchdog_dev *watchdog);
+	void (*config)(struct zocl_watchdog_dev *watchdog,
+		       struct watchdog_cfg cfg);
+};
+
+struct zocl_watchdog_dev {
+	struct platform_device       *pdev;
+	void __iomem                 *base;
+	const struct zocl_watchdog_ops    *ops;
+};
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_xclbin.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_xclbin.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2019-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    David Zhang <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_XCLBIN_H_
+#define _ZOCL_XCLBIN_H_
+
+#include <linux/uuid.h>
+
+struct zocl_xclbin {
+	int		zx_refcnt;
+	char		*zx_dtbo_path;
+	void		*zx_uuid;
+};
+
+int zocl_xclbin_init(struct drm_zocl_slot *slot);
+void zocl_xclbin_fini(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot);
+
+int zocl_xclbin_set_uuid(struct drm_zocl_slot *slot, void *uuid);
+void *zocl_xclbin_get_uuid(struct drm_zocl_slot *slot);
+int zocl_xclbin_hold(struct drm_zocl_slot *slot, const uuid_t *id);
+int zocl_lock_bitstream(struct drm_zocl_slot *slot, const uuid_t *id);
+int zocl_xclbin_release(struct drm_zocl_slot *slot, const uuid_t *id);
+int zocl_unlock_bitstream(struct drm_zocl_slot *slot, const uuid_t *id);
+struct drm_zocl_slot *zocl_get_slot(struct drm_zocl_dev *zdev,
+					uuid_t *id);
+
+int zocl_xclbin_refcount(struct drm_zocl_slot *slot);
+int zocl_xclbin_read_axlf(struct drm_zocl_dev *zdev,
+	struct drm_zocl_axlf *axlf_obj, struct sched_client_ctx *client);
+int zocl_xclbin_load_pdi(struct drm_zocl_dev *zdev, void *data,
+			struct drm_zocl_slot *slot);
+int zocl_xclbin_load_pskernel(struct drm_zocl_dev *zdev, void *data);
+bool zocl_xclbin_accel_adapter(int kds_mask);
+int zocl_xclbin_set_dtbo_path(struct drm_zocl_slot *slot, char *dtbo_path,
+		uint32_t len);
+
+#endif /* _ZOCL_XCLBIN_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_xgq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_xgq.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_XGQ_H_
+#define _ZOCL_XGQ_H_
+
+#include <linux/platform_device.h>
+#include "xgq_cmd_common.h"
+#include "xgq_cmd_vmr.h"
+
+/*
+ * Callback function for processing cmd. Cmd buffer is allocated by zocl_xgq and should be
+ * freed by callback provider when it is not needed.
+ */
+typedef void (*zxgq_cmd_handler)(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd);
+
+struct zocl_xgq_init_args {
+	struct platform_device *zxia_pdev;
+	u32			zxia_irq;
+	struct platform_device *zxia_intc_pdev;
+	void __iomem		*zxia_ring;
+	size_t			zxia_ring_size;
+	size_t			zxia_ring_slot_size;
+	void __iomem		*zxia_xgq_ip;
+	void __iomem		*zxia_cq_prod_int;
+	zxgq_cmd_handler	zxia_cmd_handler;
+	bool			zxia_simple_cmd_hdr;
+};
+
+void *zxgq_init(struct zocl_xgq_init_args *arg);
+void zxgq_fini(void *zxgq_hdl);
+void zxgq_send_response(void *zxgq_hdl, struct xgq_com_queue_entry *resp);
+
+#endif /* _ZOCL_XGQ_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zocl_xgq_plat.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zocl_xgq_plat.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#ifndef _ZOCL_XGQ_PLAT_H_
+#define _ZOCL_XGQ_PLAT_H_
+
+static inline void xgq_mem_write32(uint64_t io_hdl, uint64_t addr, uint32_t val)
+{
+	void __iomem *tgt = (void __iomem *)(uintptr_t)addr;
+
+	iowrite32(val, tgt);
+}
+#define xgq_reg_write32	xgq_mem_write32
+
+static inline uint32_t xgq_mem_read32(uint64_t io_hdl, uint64_t addr)
+{
+	void __iomem *src = (void __iomem *)(uintptr_t)addr;
+
+	return ioread32(src);
+}
+#define xgq_reg_read32	xgq_mem_read32
+
+#define XGQ_IMPL
+#define XGQ_SERVER
+#endif /* _ZOCL_XGQ_PLAT_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/include/zynq_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/include/zynq_ioctl.h
@@ -0,0 +1,578 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style CMA backed memory manager for ZynQ based OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *    Min Ma       <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+/**
+ * DOC: A GEM style driver for Xilinx edge based accelerators
+ * File *zynq_ioctl.h* defines ioctl command codes and associated structures for interacting with
+ * *zocl* driver for Xilinx FPGA platforms(Zynq/ZynqMP/Versal).
+ *
+ * Accelerator memory allocation is modeled as buffer objects (bo). zocl
+ * supports both SMMU based shared virtual memory and CMA based shared physical memory
+ * between PS and PL. zocl also supports memory management of PL-DDRs and PL-BRAMs.
+ * PL-DDR is reserved by zocl driver via device tree. Both PS Linux and PL logic can access PL-DDRs
+ *
+ * Execution model is asynchronous where execute commands are submitted using command buffers and
+ * POSIX poll is used to wait for finished commands. Commands for a compute unit can only be submitted
+ * after an explicit context has been opened by the client for that compute unit.
+ *
+ * *zocl* driver functionality is described in the following table.
+ *
+ * ==== ====================================== ============================== ==================================
+ * #    Functionality                          ioctl request code             data format
+ * ==== ====================================== ============================== ==================================
+ * 1    Allocate buffer on device              DRM_IOCTL_ZOCL_CREATE_BO       drm_zocl_create_bo
+ * 2    Allocate buffer on device with         DRM_IOCTL_ZOCL_USERPTR_BO      drm_zocl_userptr_bo
+ *      userptr
+ * 3    Get the buffer handle of given         DRM_IOCTL_ZOCL_GET_HOST_BO     drm_zocl_host_bo
+ *      physical address
+ * 4    Prepare bo for mapping into user's     DRM_IOCTL_ZOCL_MAP_BO          drm_zocl_map_bo
+ *      address space
+ * 5    Synchronize (DMA) buffer contents in   DRM_IOCTL_ZOCL_SYNC_BO         drm_zocl_sync_bo
+ *      requested direction
+ * 6    Obtain information about buffer        DRM_IOCTL_ZOCL_INFO_BO         drm_zocl_info_bo
+ *      object
+ * 7    Update bo backing storage with user's  DRM_IOCTL_ZOCL_PWRITE_BO       drm_zocl_pwrite_bo
+ *      data
+ * 8    Read back data in bo backing storage   DRM_IOCTL_ZOCL_PREAD_BO        drm_zocl_pread_bo
+ * 9    Update device view with a specific     DRM_IOCTL_ZOCL_PCAP_DOWNLOAD   drm_zocl_pcap_download
+ *      xclbin image
+ * 10   Read the xclbin and map the compute    DRM_IOCTL_ZOCL_READ_AXLF       drm_zocl_axlf
+ *      units.
+ * 11   Send an execute job to a compute unit  DRM_IOCTL_ZOCL_EXECBUF         drm_zocl_execbuf
+ * 12   Get the soft kernel command            DRM_IOCTL_ZOCL_SK_GETCMD       drm_zocl_sk_getcmd
+ *      (experimental)
+ * 13   Create the soft kernel                 DRM_IOCTL_ZOCL_SK_CREATE       drm_zocl_sk_create
+ *      (experimental)
+ * 14   Report the soft kernel state           DRM_IOCTL_ZOCL_SK_REPORT       drm_zocl_sk_report
+ *      (experimental)
+ * 15   Get Information about Compute Unit     DRM_IOCTL_ZOCL_INFO_CU         drm_zocl_info_cu
+ *      (experimental)
+ *
+ * ==== ====================================== ============================== ==================================
+ */
+
+#ifndef __ZYNQ_IOCTL_H__
+#define __ZYNQ_IOCTL_H__
+
+#ifndef __KERNEL__
+#include <stdint.h>
+#include <libdrm/drm.h>
+#include <libdrm/drm_mode.h>
+#else
+#include <uapi/drm/drm_mode.h>
+#endif /* !__KERNEL__ */
+
+/*
+ * enum drm_zocl_ops - ioctl command code enumerations
+ */
+enum drm_zocl_ops {
+	/* Buffer creation */
+	DRM_ZOCL_CREATE_BO = 0,
+	/* Buffer creation from user provided pointer */
+	DRM_ZOCL_USERPTR_BO,
+	/* Get the buffer handle of given physical address */
+	DRM_ZOCL_GET_HOST_BO,
+	/* Map buffer into application user space (no DMA is performed) */
+	DRM_ZOCL_MAP_BO,
+	/* Sync buffer (like fsync) in the desired direction by using CPU cache flushing/invalidation */
+	DRM_ZOCL_SYNC_BO,
+	/* Get information about the buffer such as physical address in the device, etc */
+	DRM_ZOCL_INFO_BO,
+	/* Update host cached copy of buffer wih user's data */
+	DRM_ZOCL_PWRITE_BO,
+	/* Update user's data with host cached copy of buffer */
+	DRM_ZOCL_PREAD_BO,
+	/* Program the Device with specific xclbin image */
+	DRM_ZOCL_PCAP_DOWNLOAD,
+	/* Send an execute job to a compute unit */
+	DRM_ZOCL_EXECBUF,
+	/* Read the xclbin and map CUs */
+	DRM_ZOCL_READ_AXLF,
+	/* Get the soft kernel command */
+	DRM_ZOCL_SK_GETCMD,
+	/* Create the soft kernel */
+	DRM_ZOCL_SK_CREATE,
+	/* Report the soft kernel state */
+	DRM_ZOCL_SK_REPORT,
+	/* Get the information about Compute Unit such as physical address in the device */
+	DRM_ZOCL_INFO_CU,
+	/* Open/Close context */
+	DRM_ZOCL_CTX,
+	/* Error injection */
+	DRM_ZOCL_ERROR_INJECT,
+	/* Request/Release AIE partition */
+	DRM_ZOCL_AIE_FD,
+	/* Reset AIE Array */
+	DRM_ZOCL_AIE_RESET,
+	/* Get the aie info command */
+	DRM_ZOCL_AIE_GETCMD,
+	/* Put the aie info command */
+	DRM_ZOCL_AIE_PUTCMD,
+	/* Set/Get freq of AIE partition */
+	DRM_ZOCL_AIE_FREQSCALE,
+	DRM_ZOCL_NUM_IOCTLS
+};
+
+enum drm_zocl_sync_bo_dir {
+	DRM_ZOCL_SYNC_BO_TO_DEVICE,
+	DRM_ZOCL_SYNC_BO_FROM_DEVICE
+};
+
+#define DRM_ZOCL_BO_FLAGS_HOST_BO    (0x1 << 26)
+#define DRM_ZOCL_BO_FLAGS_COHERENT   (0x1 << 27)
+#define DRM_ZOCL_BO_FLAGS_CMA        (0x1 << 28)
+#define DRM_ZOCL_BO_FLAGS_SVM        (0x1 << 29)
+#define DRM_ZOCL_BO_FLAGS_USERPTR    (0x1 << 30)
+#define DRM_ZOCL_BO_FLAGS_EXECBUF    (0x1 << 31)
+/**
+ * struct drm_zocl_create_bo - Create buffer object
+ * used with DRM_IOCTL_ZOCL_CREATE_BO ioctl
+ *
+ * @size:       Requested size of the buffer object
+ * @handle:     bo handle returned by the driver
+ * @flags:      DRM_ZOCL_BO_XXX flags
+ */
+struct drm_zocl_create_bo {
+	uint64_t size;
+	uint32_t handle;
+	uint32_t flags;
+};
+
+/**
+ * struct drm_zocl_userptr_bo - Create buffer object with user's pointer
+ * used with DRM_IOCTL_ZOCL_USERPTR_BO ioctl
+ *
+ * @addr:       Address of buffer allocated by user
+ * @size:       Requested size of the buffer object
+ * @handle:     bo handle returned by the driver
+ * @flags:      DRM_XOCL_BO_XXX flags
+ */
+struct drm_zocl_userptr_bo {
+	uint64_t addr;
+	uint64_t size;
+	uint32_t handle;
+	uint32_t flags;
+};
+
+/**
+ * struct drm_zocl_map_bo - Prepare a buffer object for mmap
+ * used with DRM_IOCTL_ZOCL_MAP_BO ioctl
+ *
+ * @handle:     bo handle
+ * @pad:        Unused
+ * @offset:     'Fake' offset returned by the driver which can be used with POSIX mmap
+ */
+struct drm_zocl_map_bo {
+	uint32_t handle;
+	uint32_t pad;
+	uint64_t offset;
+};
+
+/**
+ * struct drm_zocl_sync_bo - Synchronize the buffer in the requested direction
+ * via cache flush/invalidation.
+ * used with DRM_ZOCL_SYNC_BO ioctl.
+ *
+ * @handle:	GEM object handle
+ * @dir:	DRM_ZOCL_SYNC_DIR_XXX
+ * @offset:	Offset into the object to write to
+ * @size:	Length of data to write
+ */
+struct drm_zocl_sync_bo {
+	uint32_t handle;
+	enum drm_zocl_sync_bo_dir dir;
+	uint64_t offset;
+	uint64_t size;
+};
+
+/**
+ * struct drm_zocl_info_bo - Obtain information about buffer object
+ * used with DRM_IOCTL_ZOCL_INFO_BO ioctl
+ *
+ * @handle:	GEM object handle
+ * @flags:	User BO flags
+ * @size:	Size of BO
+ * @paddr:	physical address
+ */
+struct drm_zocl_info_bo {
+	uint32_t	handle;
+	uint32_t	flags;
+	uint64_t	size;
+	uint64_t	paddr;
+};
+
+/**
+ * struct drm_zocl_host_bo - Get the buffer handle of given physical address
+ * used with DRM_IOCTL_ZOCL_GET_HOST_BO ioctl
+ *
+ * @paddr:	physical address
+ * @size:	Size of BO
+ * @handle:	GEM object handle
+ */
+struct drm_zocl_host_bo {
+	uint64_t	paddr;
+	size_t		size;
+	uint32_t	handle;
+};
+
+/**
+ * struct drm_zocl_pwrite_bo - Update bo with user's data
+ * used with DRM_IOCTL_ZOCL_PWRITE_BO ioctl
+ *
+ * @handle:	GEM object handle
+ * @pad:	Padding
+ * @offset:	Offset into the object to write to
+ * @size:	Length of data to write
+ * @data_ptr:	Pointer to read the data from (pointers not 32/64 compatible)
+ */
+struct drm_zocl_pwrite_bo {
+	uint32_t handle;
+	uint32_t pad;
+	uint64_t offset;
+	uint64_t size;
+	uint64_t data_ptr;
+};
+
+/**
+ * struct drm_zocl_pread_bo - Read data from bo
+ * used with DRM_IOCTL_ZOCL_PREAD_BO ioctl
+ *
+ * @handle:	GEM object handle
+ * @pad:	Padding
+ * @offset:	Offset into the object to read from
+ * @size:	Length of data to wrreadite
+ * @data_ptr:	Pointer to write the data into (pointers not 32/64 compatible)
+ */
+struct drm_zocl_pread_bo {
+	uint32_t handle;
+	uint32_t pad;
+	uint64_t offset;
+	uint64_t size;
+	uint64_t data_ptr;
+};
+
+/**
+ * struct drm_zocl_info_cu - Get information about Compute Unit (experimental)
+ * used with DRM_IOCTL_ZOCL_INFO_CU ioctl
+ *
+ *  @paddr: Physical address
+ *  @apt_idx: Aperture index
+ *  @cu_idx: CU index
+ */
+struct drm_zocl_info_cu {
+	uint64_t paddr;
+	int apt_idx;
+	int cu_idx;
+};
+
+enum drm_zocl_ctx_code {
+	ZOCL_CTX_OP_ALLOC_CTX = 0,
+	ZOCL_CTX_OP_FREE_CTX,
+	ZOCL_CTX_OP_OPEN_GCU_FD,
+	ZOCL_CTX_OP_ALLOC_GRAPH_CTX,
+	ZOCL_CTX_OP_FREE_GRAPH_CTX,
+	ZOCL_CTX_OP_ALLOC_AIE_CTX,
+	ZOCL_CTX_OP_FREE_AIE_CTX
+};
+
+#define	ZOCL_CTX_NOOPS		0
+#define	ZOCL_CTX_SHARED		(1 << 0)
+#define	ZOCL_CTX_EXCLUSIVE	(1 << 1)
+#define	ZOCL_CTX_VERBOSE	(1 << 2)
+#define	ZOCL_CTX_PRIMARY	(1 << 3)
+#define	ZOCL_CTX_VIRT_CU_INDEX	0xffffffff
+
+struct drm_zocl_ctx {
+	uint64_t uuid_ptr;
+	uint64_t uuid_size;
+	union {
+		uint32_t cu_index;
+		uint32_t graph_id;
+	};
+	uint32_t flags;
+	// unused, in future it would return context id
+	uint32_t handle;
+	enum drm_zocl_ctx_code op;
+};
+
+struct drm_zocl_aie_fd {
+	uint32_t partition_id;
+	uint32_t uid;
+	int fd;
+};
+
+struct drm_zocl_aie_reset {
+	uint32_t partition_id;
+};
+
+struct drm_zocl_aie_freq_scale {
+	uint32_t partition_id;
+	uint64_t freq;
+	bool dir;
+};
+
+/**
+ * Opcodes for the embedded scheduler provided by the client to the driver
+ */
+enum drm_zocl_execbuf_code {
+  DRM_ZOCL_EXECBUF_RUN_KERNEL = 0,
+  DRM_ZOCL_EXECBUF_RUN_KERNEL_XYZ,
+  DRM_ZOCL_EXECBUF_PING,
+  DRM_ZOCL_EXECBUF_DEBUG,
+};
+
+/**
+ * State of exec request managed by the kernel driver
+ */
+enum drm_zocl_execbuf_state {
+  DRM_ZOCL_EXECBUF_STATE_COMPLETE = 0,
+  DRM_ZOCL_EXECBUF_STATE_RUNNING,
+  DRM_ZOCL_EXECBUF_STATE_SUBMITTED,
+  DRM_ZOCL_EXECBUF_STATE_QUEUED,
+  DRM_ZOCL_EXECBUF_STATE_ERROR,
+  DRM_ZOCL_EXECBUF_STATE_ABORT,
+};
+
+/**
+ * struct drm_zocl_execbuf - Submit a command buffer for execution on a compute
+ * unit  (experimental) used with DRM_IOCTL_ZOCL_EXECBUF ioctl
+ *
+ * @ctx_id:         Pass 0
+ * @exec_bo_handle: BO handle of command buffer formatted as ERT command
+ */
+struct drm_zocl_execbuf {
+  uint32_t ctx_id;
+  uint32_t exec_bo_handle;
+};
+
+/*
+ * enum drm_zocl_platform_flags - can be used for axlf bitstream
+ */
+enum drm_zocl_axlf_flags {
+	DRM_ZOCL_PLATFORM_BASE		= 0,
+	DRM_ZOCL_PLATFORM_PR		= (1 << 0),
+	DRM_ZOCL_PLATFORM_FLAT		= (1 << 1),
+	DRM_ZOCL_FORCE_PROGRAM		= (1 << 2)
+};
+
+/**
+ * struct argument_info - Kernel argument information
+ *
+ * @name:	argument name
+ * @offset:	argument offset in CU
+ * @size:	argument size in bytes
+ * @dir:	input or output argument for a CU
+ */
+struct argument_info {
+	char		name[64];
+	uint32_t	offset;
+	uint32_t	size;
+	uint32_t	dir;
+};
+
+/* Kernel features macro */
+#define KRNL_SW_RESET	(1 << 0)
+
+/**
+ * struct kernel_info - Kernel information
+ *
+ * @name:	kernel name
+ * @range:	kernel range
+ * @anums:	number of argument
+ * @args:	argument array
+ */
+struct kernel_info {
+	char                     name[64];
+	uint32_t		 range;
+	int		         anums;
+	int			 features;
+	struct argument_info	 args[];
+};
+
+/**
+ * struct drm_zocl_kds - KDS user configuration
+ *
+ * @polling:	poll for command completion
+ */
+struct drm_zocl_kds {
+	uint32_t polling:1;
+	uint32_t unused:31;
+};
+
+/**
+ * struct drm_zocl_axlf - Read xclbin (AXLF) device image and map CUs (experimental)
+ * used with DRM_IOCTL_ZOCL_READ_AXLF ioctl
+ *
+ * @za_xclbin_ptr: Pointer to xclbin (AXLF) object
+ * @za_flags:   platform flags
+ * @za_ksize:	size of kernels in bytes
+ * @za_kernels:	pointer of argument array
+ * @za_slot_id:	xclbin slot
+ * @hw_gen:	aie generation
+ **/
+struct drm_zocl_axlf {
+	struct axlf		*za_xclbin_ptr;
+	uint32_t		za_flags;
+	int			za_ksize;
+	char			*za_kernels;
+	uint32_t		za_slot_id;
+	char			*za_dtbo_path;
+	uint32_t 		za_dtbo_path_len;
+	uint8_t		        hw_gen;
+	struct drm_zocl_kds	kds_cfg;
+};
+
+#define	ZOCL_MAX_NAME_LENGTH		32
+#define	ZOCL_MAX_PATH_LENGTH		255
+#define AIE_INFO_SIZE			4096
+
+/**
+ * struct drm_zocl_sk_getcmd - Get the soft kernel command  (experimental)
+ * used with DRM_IOCTL_ZOCL_SK_GETCMD ioctl
+ *
+ * @opcode       : opcode for the Soft Kernel Command Packet
+ * @start_cuidx  : start index of compute units
+ * @cu_nums      : number of compute units in program
+ * @size         : size in bytes of soft kernel image
+ * @paddr        : soft kernel image's physical address (little endian)
+ * @name         : symbol name of soft kernel
+ * @bohdl        : BO to hold soft kernel image
+ * @meta_bohdl   : BO to hold metadata
+ * @uuid         : UUID for the xclbin
+ */
+struct drm_zocl_sk_getcmd {
+	uint32_t	opcode;
+	uint32_t	start_cuidx;
+	uint32_t	cu_nums;
+	char		name[ZOCL_MAX_NAME_LENGTH];
+	int		bohdl;
+	int		meta_bohdl;
+	unsigned char	uuid[16];
+};
+
+enum aie_info_code {
+	GRAPH_STATUS = 1,
+};
+
+/**
+ * struct drm_zocl_aie_cmd - Get the aie command
+ * used with DRM_IOCTL_ZOCL_AIE_GETCMD and DRM_IOCTL_ZOCL_AIE_PUTCMD ioctl
+ *
+ * @opcode       : opcode for the Aie Command Packet
+ * @size         : size in bytes of info data
+ * @info         : information to transfer
+ */
+struct drm_zocl_aie_cmd {
+	uint32_t	opcode;
+	uint32_t	size;
+	char		info[AIE_INFO_SIZE];
+};
+
+/**
+ * struct drm_zocl_sk_create - Create a soft kernel  (experimental)
+ * used with DRM_IOCTL_ZOCL_SK_CREATE ioctl
+ *
+ * @cu_idx     : Compute unit index
+ * @handle     : Buffer object handle
+ */
+struct drm_zocl_sk_create {
+	uint32_t	cu_idx;
+	int		handle;
+};
+
+/**
+ * State of soft compute unit
+ */
+enum drm_zocl_scu_state {
+	ZOCL_SCU_STATE_DONE,
+	ZOCL_SCU_STATE_READY,
+	ZOCL_SCU_STATE_CRASH,
+	ZOCL_SCU_STATE_FINI,
+};
+
+/**
+ * struct drm_zocl_sk_report- Report the Soft Kernel State  (experimental)
+ * used with DRM_IOCTL_ZOCL_SK_REPORT ioctl
+ *
+ * @cu_idx     : Compute unit index
+ * @cu_state   : State of the Soft Compute Unit
+ */
+struct drm_zocl_sk_report {
+	uint32_t		cu_idx;
+	uint32_t		cu_domain;
+	enum drm_zocl_scu_state	cu_state;
+};
+
+enum drm_zocl_err_ops {
+	ZOCL_ERROR_OP_INJECT = 0,
+	ZOCL_ERROR_OP_CLEAR_ALL
+};
+
+struct drm_zocl_error_inject {
+	enum drm_zocl_err_ops	err_ops;
+	uint16_t		err_num;
+	uint16_t		err_driver;
+	uint16_t		err_severity;
+	uint16_t		err_module;
+	uint16_t		err_class;
+};
+
+#define DRM_IOCTL_ZOCL_CREATE_BO       DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_CREATE_BO,     \
+                                       struct drm_zocl_create_bo)
+#define DRM_IOCTL_ZOCL_USERPTR_BO      DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_USERPTR_BO,     \
+                                       struct drm_zocl_userptr_bo)
+#define DRM_IOCTL_ZOCL_GET_HOST_BO     DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_GET_HOST_BO,     \
+                                       struct drm_zocl_host_bo)
+#define DRM_IOCTL_ZOCL_MAP_BO          DRM_IOWR(DRM_COMMAND_BASE +          \
+                                       DRM_ZOCL_MAP_BO, struct drm_zocl_map_bo)
+#define DRM_IOCTL_ZOCL_SYNC_BO         DRM_IOWR(DRM_COMMAND_BASE +          \
+                                       DRM_ZOCL_SYNC_BO, struct drm_zocl_sync_bo)
+#define DRM_IOCTL_ZOCL_INFO_BO         DRM_IOWR(DRM_COMMAND_BASE +          \
+                                       DRM_ZOCL_INFO_BO, struct drm_zocl_info_bo)
+#define DRM_IOCTL_ZOCL_PWRITE_BO       DRM_IOWR(DRM_COMMAND_BASE +  \
+                                       DRM_ZOCL_PWRITE_BO, \
+                                       struct drm_zocl_pwrite_bo)
+#define DRM_IOCTL_ZOCL_PREAD_BO        DRM_IOWR(DRM_COMMAND_BASE +      \
+                                       DRM_ZOCL_PREAD_BO, struct drm_zocl_pread_bo)
+#define DRM_IOCTL_ZOCL_EXECBUF         DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_EXECBUF, struct drm_zocl_execbuf)
+#define DRM_IOCTL_ZOCL_READ_AXLF       DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_READ_AXLF, struct drm_zocl_axlf)
+#define DRM_IOCTL_ZOCL_SK_GETCMD       DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_SK_GETCMD, struct drm_zocl_sk_getcmd)
+#define DRM_IOCTL_ZOCL_SK_CREATE       DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_SK_CREATE, struct drm_zocl_sk_create)
+#define	DRM_IOCTL_ZOCL_SK_REPORT       DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_SK_REPORT, struct drm_zocl_sk_report)
+#define DRM_IOCTL_ZOCL_INFO_CU         DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_INFO_CU, struct drm_zocl_info_cu)
+#define DRM_IOCTL_ZOCL_CTX             DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_CTX, struct drm_zocl_ctx)
+#define DRM_IOCTL_ZOCL_ERROR_INJECT    DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_ERROR_INJECT, struct drm_zocl_error_inject)
+#define DRM_IOCTL_ZOCL_AIE_FD          DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_AIE_FD, struct drm_zocl_aie_fd)
+#define DRM_IOCTL_ZOCL_AIE_RESET       DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_AIE_RESET, struct drm_zocl_aie_reset)
+#define DRM_IOCTL_ZOCL_AIE_GETCMD      DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_AIE_GETCMD, struct drm_zocl_aie_cmd)
+#define DRM_IOCTL_ZOCL_AIE_PUTCMD      DRM_IOWR(DRM_COMMAND_BASE + \
+                                       DRM_ZOCL_AIE_PUTCMD, struct drm_zocl_aie_cmd)
+#define DRM_IOCTL_ZOCL_AIE_FREQSCALE   DRM_IOWR(DRM_COMMAND_BASE + \
+				       DRM_ZOCL_AIE_FREQSCALE, struct drm_zocl_aie_freq_scale)
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/scu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/scu.c
@@ -0,0 +1,356 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2022 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Min Ma <min.ma@xilinx.com>
+ *        Jeff Lin <jeffli@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "zocl_drv.h"
+#include "zocl_sk.h"
+#include "xrt_cu.h"
+
+struct zocl_scu {
+	struct xrt_cu		 base;
+	struct platform_device	*pdev;
+	struct drm_zocl_bo	*sc_bo;
+	/*
+	 * This semaphore is used for each soft kernel
+	 * CU to wait for next command. When new command
+	 * for this CU comes in or we are told to abort
+	 * a CU, ert will up this semaphore.
+	 */
+	struct semaphore	sc_sem;
+
+	/*
+	 * soft cu pid and parent pid. This can be used to identify if the
+	 * soft cu is still running or not. The parent should never crash
+	 */
+	uint32_t		sc_pid;
+	uint32_t		sc_parent_pid;
+};
+
+static ssize_t debug_show(struct device *dev,
+	struct device_attribute *attr, char *buf)
+{
+#if 0
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_scu *scu = platform_get_drvdata(pdev);
+	struct xrt_cu *xcu = &scu->base;
+#endif
+	/* Place holder for now. */
+	return 0;
+}
+
+static ssize_t debug_store(struct device *dev,
+	struct device_attribute *da, const char *buf, size_t count)
+{
+#if 0
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_scu *scu = platform_get_drvdata(pdev);
+	struct xrt_cu *xcu = &scu->base;
+#endif
+
+	/* Place holder for now. */
+	return count;
+}
+static DEVICE_ATTR_RW(debug);
+
+static ssize_t
+cu_stat_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_scu *scu = platform_get_drvdata(pdev);
+
+	return show_cu_stat(&scu->base, buf);
+}
+static DEVICE_ATTR_RO(cu_stat);
+
+static ssize_t
+cu_info_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_scu *scu = platform_get_drvdata(pdev);
+
+	return show_cu_info(&scu->base, buf);
+}
+static DEVICE_ATTR_RO(cu_info);
+
+static ssize_t
+stat_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct zocl_scu *scu = platform_get_drvdata(pdev);
+
+	return show_formatted_cu_stat(&scu->base, buf);
+}
+static DEVICE_ATTR_RO(stat);
+
+static struct attribute *scu_attrs[] = {
+	&dev_attr_debug.attr,
+	&dev_attr_cu_stat.attr,
+	&dev_attr_cu_info.attr,
+	&dev_attr_stat.attr,
+	NULL,
+};
+
+static const struct attribute_group scu_attrgroup = {
+	.attrs = scu_attrs,
+};
+
+static int configure_soft_kernel(u32 cuidx, char kname[64], unsigned char uuid[16])
+{
+	struct drm_zocl_dev *zdev = zocl_get_zdev();
+	struct soft_krnl *sk = zdev->soft_kernel;
+	struct soft_krnl_cmd *scmd = NULL;
+	struct config_sk_image_uuid *cp = NULL;
+
+	cp = kmalloc(sizeof(struct config_sk_image_uuid), GFP_KERNEL);
+	cp->start_cuidx = cuidx;
+	cp->num_cus = 1;
+	strncpy((char *)cp->sk_name,kname,PS_KERNEL_NAME_LENGTH);
+	memcpy(cp->sk_uuid,uuid,sizeof(cp->sk_uuid));
+
+	// Locking soft kernel data structure
+	mutex_lock(&sk->sk_lock);
+
+	/*
+	 * Fill up a soft kernel command and add to soft
+	 * kernel command list
+	 */
+	scmd = kmalloc(sizeof(struct soft_krnl_cmd), GFP_KERNEL);
+	if (!scmd) {
+		DRM_WARN("Config Soft CU failed: no memory.\n");
+		mutex_unlock(&sk->sk_lock);
+		return -ENOMEM;
+	}
+
+	scmd->skc_opcode = ERT_SK_CONFIG;
+	scmd->skc_packet = cp;
+
+	list_add_tail(&scmd->skc_list, &sk->sk_cmd_list);
+	// Releasing soft kernel data structure lock
+	mutex_unlock(&sk->sk_lock);
+
+	/* start CU by waking up PS kernel handler */
+	wake_up_interruptible(&sk->sk_wait_queue);
+
+	return 0;
+}
+
+static int scu_probe(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = NULL;
+	struct xrt_cu_info *info = NULL;
+	struct drm_zocl_dev *zdev = NULL;
+	int err = 0;
+
+	zcu = kzalloc(sizeof(*zcu), GFP_KERNEL);
+	if (!zcu)
+		return -ENOMEM;
+
+	zcu->pdev = pdev;
+	zcu->base.dev = &pdev->dev;
+	sema_init(&zcu->sc_sem, 0);
+
+	info = dev_get_platdata(&pdev->dev);
+	memcpy(&zcu->base.info, info, sizeof(struct xrt_cu_info));
+
+	zdev = zocl_get_zdev();
+	zcu->sc_bo = zocl_drm_create_bo(zdev->ddev, SOFT_KERNEL_REG_SIZE, ZOCL_BO_FLAGS_CMA);
+	if (IS_ERR(zcu->sc_bo)) {
+		return -ENOMEM;
+		goto err;
+	}
+	zcu->sc_bo->flags = ZOCL_BO_FLAGS_CMA;
+	err = xrt_cu_scu_init(&zcu->base, zcu->sc_bo->cma_base.vaddr, &zcu->sc_sem);
+	if (err) {
+		DRM_ERROR("Not able to initial SCU %p\n", zcu);
+		goto err;
+	}
+
+	platform_set_drvdata(pdev, zcu);
+
+	err = sysfs_create_group(&pdev->dev.kobj, &scu_attrgroup);
+	if (err)
+		zocl_err(&pdev->dev, "create SCU attrs failed: %d", err);
+
+	err = configure_soft_kernel(info->cu_idx,info->kname,info->uuid);
+	if (err)
+		zocl_err(&pdev->dev, "configuring SCU failed: %d", err);
+
+	zocl_info(&pdev->dev, "SCU[%d] created", info->cu_idx);
+	return 0;
+err:
+	kfree(zcu);
+	return err;
+}
+
+static int scu_remove(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+	struct drm_zocl_dev *zdev = zocl_get_zdev();
+	struct xrt_cu_info *info = &zcu->base.info;
+
+	xrt_cu_scu_fini(&zcu->base);
+
+	zocl_kds_del_scu(zdev, &zcu->base);
+
+	if (zcu->base.res)
+		vfree(zcu->base.res);
+
+	// Free Command Buffer BO
+	zocl_drm_free_bo(zcu->sc_bo);
+	sysfs_remove_group(&pdev->dev.kobj, &scu_attrgroup);
+
+	zocl_info(&pdev->dev, "SCU[%d] removed", info->cu_idx);
+	kfree(zcu);
+
+	return 0;
+}
+
+static struct platform_device_id scu_id_table[] = {
+	{"SCU", 0 },
+	{ /* end of table */ },
+};
+
+struct platform_driver scu_driver = {
+	.probe		= scu_probe,
+	.remove		= scu_remove,
+	.driver		= {
+		.name = "scu_drv",
+	},
+	.id_table	= scu_id_table,
+};
+
+u32 zocl_scu_get_status(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+
+	BUG_ON(!zcu);
+	return xrt_cu_get_status(&zcu->base);
+}
+
+int zocl_scu_create_sk(struct platform_device *pdev, u32 pid, u32 parent_pid, struct drm_file *filp, int *boHandle)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+	int ret = 0;
+
+	zcu->sc_pid = pid;
+	zcu->sc_parent_pid = parent_pid;
+	ret = drm_gem_handle_create(filp,
+				    &zcu->sc_bo->cma_base.base, boHandle);
+	return(ret);
+}
+
+int zocl_scu_wait_cmd_sk(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+	int ret = 0;
+	u32 *vaddr = zcu->sc_bo->cma_base.vaddr;
+
+	/* If the CU is running, mark it as done */
+	if (*vaddr & 1)
+		/* Clear Bit 0 and set Bit 1 */
+		*vaddr = 2 | (*vaddr & ~3);
+
+	if (down_interruptible(&zcu->sc_sem)) {
+		ret = -EINTR;
+	}
+
+	if (ret) {
+		/* We are interrupted */
+		return ret;
+	}
+
+	/* Clear Bit 1 and set Bit 0 */
+	*vaddr = 1 | (*vaddr & ~3);
+
+	return 0;
+}
+
+int zocl_scu_wait_ready(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+	struct xrt_cu *xcu = &zcu->base;
+	int ret = 0;
+
+	// Wait for PS kernel initizliation complete
+	if(down_timeout(&zcu->sc_sem,100)) {
+		zocl_err(&pdev->dev, "PS kernel initialization timed out!");
+		return -ETIME;
+	}
+	ret = zocl_kds_add_scu(zocl_get_zdev(), xcu);
+	if (ret) {
+		zocl_err(&pdev->dev, "Not able to add SCU %p to KDS", zcu);
+		return ret;
+	}
+	return 0;
+}
+
+void zocl_scu_sk_ready(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+
+	up(&zcu->sc_sem);
+}
+
+void zocl_scu_sk_crash(struct platform_device *pdev)
+{
+	//struct zocl_scu *zcu = platform_get_drvdata(pdev);
+
+	// TO-DO
+	// Add taks to indicate PS kernel crash
+	return; /* Place holder */
+}
+
+void zocl_scu_sk_shutdown(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+	struct pid *p = NULL;
+	struct task_struct *task = NULL;
+	int ret = 0;
+
+	// Wait for PS Kernel Process to finish
+	p = find_get_pid(zcu->sc_pid);
+	if(!p) {
+		// Process already gone
+		goto skip_kill;
+	}
+
+	task = pid_task(p, PIDTYPE_PID);
+	if(!task) {
+		DRM_WARN("Failed to get task for pid %d\n", zcu->sc_pid);
+		put_pid(p);
+		goto skip_kill;
+	}
+
+	if(zcu->sc_parent_pid != task_ppid_nr(task)) {
+		DRM_WARN("Parent pid does not match\n");
+		put_pid(p);
+		goto skip_kill;
+	}
+
+	ret = kill_pid(p, SIGTERM, 1);
+	if (ret) {
+		DRM_WARN("Failed to terminate SCU pid %d.  Performing SIGKILL.\n", zcu->sc_pid);
+		kill_pid(p, SIGKILL, 1);
+	}
+	put_pid(p);
+
+	if (down_timeout(&zcu->sc_sem,100))
+		DRM_WARN("Wait for PS kernel timeout\n");
+ skip_kill:
+	return;
+}
+
+void zocl_scu_sk_fini(struct platform_device *pdev)
+{
+	struct zocl_scu *zcu = platform_get_drvdata(pdev);
+
+	up(&zcu->sc_sem);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_aie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_aie.c
@@ -0,0 +1,989 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu <yliu@xilinc.com>
+ *    Himanshu Choudhary <hchoudha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "zocl_drv.h"
+#include "zocl_aie.h"
+#include "xrt_xclbin.h"
+#include "xclbin.h"
+#include "sched_exec.h"
+
+#ifndef __NONE_PETALINUX__
+#include <linux/xlnx-ai-engine.h>
+#endif
+
+#include <linux/workqueue.h>
+#include <linux/delay.h>
+
+static inline u8
+get_error_module(enum aie_module_type aie_module) {
+	switch (aie_module) {
+	case AIE_MEM_MOD:
+		return XRT_ERROR_MODULE_AIE_MEMORY;
+	case AIE_CORE_MOD:
+		return XRT_ERROR_MODULE_AIE_CORE;
+	case AIE_PL_MOD:
+		return XRT_ERROR_MODULE_AIE_PL;
+	case AIE_NOC_MOD:
+		return XRT_ERROR_MODULE_AIE_NOC;
+	default:
+		return XRT_ERROR_MODULE_UNKNOWN;
+	}
+}
+
+static inline u8
+get_error_num(u8 aie_category) {
+	switch (aie_category) {
+	case AIE_ERROR_CATEGORY_SATURATION:
+		return XRT_ERROR_NUM_AIE_SATURATION;
+	case AIE_ERROR_CATEGORY_FP:
+		return XRT_ERROR_NUM_AIE_FP;
+	case AIE_ERROR_CATEGORY_STREAM:
+		return XRT_ERROR_NUM_AIE_STREAM;
+	case AIE_ERROR_CATEGORY_ACCESS:
+		return XRT_ERROR_NUM_AIE_ACCESS;
+	case AIE_ERROR_CATEGORY_BUS:
+		return XRT_ERROR_NUM_AIE_BUS;
+	case AIE_ERROR_CATEGORY_INSTRUCTION:
+		return XRT_ERROR_NUM_AIE_INSTRUCTION;
+	case AIE_ERROR_CATEGORY_ECC:
+		return XRT_ERROR_NUM_AIE_ECC;
+	case AIE_ERROR_CATEGORY_LOCK:
+		return XRT_ERROR_NUM_AIE_LOCK;
+	case AIE_ERROR_CATEGORY_DMA:
+		return XRT_ERROR_NUM_AIE_DMA;
+	case AIE_ERROR_CATEGORY_MEM_PARITY:
+		return XRT_ERROR_NUM_AIE_MEM_PARITY;
+	default:
+		return XRT_ERROR_NUM_UNKNOWN;
+	}
+}
+
+static int
+zocl_aie_cache_error(struct aie_error_cache *zerr, struct aie_error *err)
+{
+	struct aie_error *temp;
+
+	/* If the current error cache is full, double the cache size */
+	if (zerr->num == zerr->cap) {
+		temp = vzalloc(sizeof (struct aie_error) * zerr->cap * 2);
+		if (!temp)
+			return -ENOMEM;
+
+		memcpy(temp, zerr->errors, sizeof (struct aie_error) *
+		    zerr->num);
+		zerr->cap *= 2;
+		vfree(zerr->errors);
+		zerr->errors = temp;
+	}
+
+	zerr->errors[zerr->num].error_id = err->error_id;
+	zerr->errors[zerr->num].module = err->module;
+	zerr->errors[zerr->num].loc.col = err->loc.col;
+	zerr->errors[zerr->num].loc.row = err->loc.row;
+	zerr->num++;
+
+	return 0;
+}
+
+static bool
+is_cached_error(struct aie_error_cache *zerr, struct aie_error *err)
+{
+	int i;
+
+	for (i = 0; i < zerr->num; i++) {
+		if (zerr->errors[i].error_id == err->error_id &&
+		    zerr->errors[i].category == err->category &&
+		    zerr->errors[i].module == err->module &&
+		    zerr->errors[i].loc.col == err->loc.col &&
+		    zerr->errors[i].loc.row == err->loc.row)
+			break;
+	}
+
+	return i < zerr->num ? true : false;
+}
+
+static void
+zocl_aie_error_cb(void *arg)
+{
+	struct drm_zocl_dev *zdev = arg;
+	struct aie_errors *errors;
+	int i;
+
+	if (!zdev) {
+		DRM_WARN("%s: zdev is not initialized\n", __func__);
+		return;
+	}
+
+	mutex_lock(&zdev->aie_lock);
+	if (!zdev->aie) {
+		DRM_WARN("%s: AIE image is not loaded.\n", __func__);
+		mutex_unlock(&zdev->aie_lock);
+		return;
+	}
+
+	if (!zdev->aie->aie_dev) {
+		DRM_WARN("%s: No available AIE partition.\n", __func__);
+		mutex_unlock(&zdev->aie_lock);
+		return;
+	}
+
+	errors = aie_get_errors(zdev->aie->aie_dev);
+	if (IS_ERR(errors)) {
+		DRM_WARN("%s: aie_get_errors failed\n", __func__);
+		mutex_unlock(&zdev->aie_lock);
+		return;
+	}
+
+	for (i = 0; i < errors->num_err; i++) {
+		xrtErrorCode err_code;
+
+		DRM_INFO("Get AIE asynchronous Error: "
+		    "error_id %d Mod %d, category %d, Col %d, Row %d\n",
+		    errors->errors[i].error_id,
+		    errors->errors[i].module,
+		    errors->errors[i].category,
+		    errors->errors[i].loc.col,
+		    errors->errors[i].loc.row
+		    );
+
+		if (is_cached_error(&zdev->aie->err, &((errors->errors)[i])))
+			continue;
+
+		err_code = XRT_ERROR_CODE_BUILD(
+		    get_error_num(errors->errors[i].category),
+		    XRT_ERROR_DRIVER_AIE,
+		    XRT_ERROR_SEVERITY_CRITICAL,
+		    get_error_module(errors->errors[i].module),
+		    XRT_ERROR_CLASS_AIE
+		    );
+
+		zocl_insert_error_record(zdev, err_code);
+		zocl_aie_cache_error(&zdev->aie->err, &((errors->errors)[i]));
+	}
+
+	aie_free_errors(errors);
+
+	mutex_unlock(&zdev->aie_lock);
+}
+
+int
+zocl_aie_request_part_fd(struct drm_zocl_dev *zdev, void *data)
+{
+	struct drm_zocl_aie_fd *args = data;
+	int fd;
+	int rval = 0;
+
+	mutex_lock(&zdev->aie_lock);
+
+	if (!zdev->aie) {
+		DRM_ERROR("AIE image is not loaded.\n");
+		rval = -ENODEV;
+		goto done;
+	}
+
+	if (!zdev->aie->aie_dev) {
+		DRM_ERROR("No available AIE partition.\n");
+		rval = -ENODEV;
+		goto done;
+	}
+
+	if (zdev->aie->partition_id != args->partition_id) {
+		DRM_ERROR("AIE partition %d does not exist.\n",
+		    args->partition_id);
+		rval = -ENODEV;
+		goto done;
+	}
+
+	fd = aie_partition_get_fd(zdev->aie->aie_dev);
+	if (fd < 0) {
+		DRM_ERROR("Get AIE partition %d fd: %d\n",
+		    args->partition_id, fd);
+		rval = fd;
+		goto done;
+	}
+
+	args->fd = fd;
+
+	zdev->aie->fd_cnt++;
+
+done:
+	mutex_unlock(&zdev->aie_lock);
+
+	return rval;
+}
+
+int
+zocl_create_aie(struct drm_zocl_dev *zdev, struct axlf *axlf, void *aie_res, uint8_t hw_gen)
+{
+	uint64_t offset;
+	uint64_t size;
+	struct aie_partition_req req;
+	int rval = 0;
+
+	rval = xrt_xclbin_section_info(axlf, AIE_METADATA, &offset, &size);
+	if (rval)
+		return rval;
+
+	mutex_lock(&zdev->aie_lock);
+
+	/* AIE is reset and no PDI is loaded after reset */
+	if (zdev->aie && zdev->aie->aie_reset) {
+		rval = -ENODEV;
+		DRM_ERROR("PDI is not loaded after AIE reset.\n");
+		goto done;
+	}
+
+	if (!zdev->aie) {
+		zdev->aie = vzalloc(sizeof (struct zocl_aie));
+		if (!zdev->aie) {
+			rval = -ENOMEM;
+			DRM_ERROR("Fail to allocate memory.\n");
+			goto done;
+		}
+
+		zdev->aie->err.errors = vzalloc(sizeof (struct aie_error) *
+		    ZOCL_AIE_ERROR_CACHE_CAP);
+		if (!zdev->aie->err.errors) {
+			rval = -ENOMEM;
+			vfree(zdev->aie);
+			DRM_ERROR("Fail to allocate memory.\n");
+			goto done;
+		}
+
+		zdev->aie->err.num = 0;
+		zdev->aie->err.cap = ZOCL_AIE_ERROR_CACHE_CAP;
+
+	}
+
+	if (!zdev->aie->wq) {
+		zdev->aie->wq = create_singlethread_workqueue("aie-workq");
+		if (!zdev->aie->wq) {
+			rval = -ENOMEM;
+			DRM_ERROR("Fail to create work queue.\n");
+			goto done;
+		}
+	}
+
+	/* TODO figure out the partition id and uid from xclbin or PDI */
+	req.partition_id = 1;
+	req.uid = 0;
+	/* only aie-1 supports resources */
+	if (hw_gen == 1)
+		req.meta_data = (u64)aie_res;
+
+	if (zdev->aie->aie_dev) {
+		DRM_INFO("Partition %d already requested\n",
+		    req.partition_id);
+		goto done;
+	}
+
+	zdev->aie->aie_dev = aie_partition_request(&req);
+
+	if (IS_ERR(zdev->aie->aie_dev)) {
+		rval = PTR_ERR(zdev->aie->aie_dev);
+		DRM_ERROR("Request AIE partition %d, %d\n",
+		    req.partition_id, rval);
+		goto done;
+	}
+
+	zdev->aie->partition_id = req.partition_id;
+	zdev->aie->uid = req.uid;
+
+	/* Register AIE error call back function. */
+	/* only aie-1 supports error management*/
+	if (hw_gen == 1) {
+		rval = aie_register_error_notification(zdev->aie->aie_dev,
+		zocl_aie_error_cb, zdev);
+	}
+	mutex_unlock(&zdev->aie_lock);
+
+	zocl_init_aie(zdev);
+
+	return 0;
+
+done:
+	mutex_unlock(&zdev->aie_lock);
+
+	return rval;
+}
+
+void
+zocl_destroy_aie(struct drm_zocl_dev *zdev)
+{
+	if (!zdev->aie_information)
+		return;
+
+	vfree(zdev->aie_information);
+	mutex_lock(&zdev->aie_lock);
+
+	if (!zdev->aie) {
+		mutex_unlock(&zdev->aie_lock);
+		return;
+	}
+
+	if (zdev->aie->aie_dev)
+		aie_partition_release(zdev->aie->aie_dev);
+
+	if (zdev->aie->wq)
+		destroy_workqueue(zdev->aie->wq);
+
+	vfree(zdev->aie->err.errors);
+	vfree(zdev->aie);
+	zdev->aie = NULL;
+	mutex_unlock(&zdev->aie_lock);
+}
+
+static void
+zocl_aie_reset_work(struct work_struct *aie_work)
+{
+	struct aie_work_data *data = container_of(aie_work,
+	    struct aie_work_data, work);
+	struct drm_zocl_dev *zdev= data->zdev;
+	int i;
+
+	/*
+	 * Note: we can not hold lock here because this
+	 *       work thread is invoked within a lock and
+	 *       that lock will not be relased until the
+	 *       work is flushed.
+	 */
+
+	/*
+	 * Reset AIE by releasing AIE partition. The times we
+	 * release AIE partition is based on the # of fd is
+	 * requested + 1.
+	 */
+	for (i = 0; i < zdev->aie->fd_cnt + 1; i++)
+		aie_partition_release(zdev->aie->aie_dev);
+
+	zdev->aie->fd_cnt = 0;
+}
+
+int
+zocl_aie_reset(struct drm_zocl_dev *zdev)
+{
+	struct aie_partition_req req;
+	bool aie_available = false;
+	struct aie_work_data *data;
+	int count;
+
+	mutex_lock(&zdev->aie_lock);
+
+	if (!zdev->aie) {
+		mutex_unlock(&zdev->aie_lock);
+		DRM_ERROR("AIE image is not loaded.\n");
+		return -ENODEV;
+	}
+
+	if (!zdev->aie->aie_dev) {
+		mutex_unlock(&zdev->aie_lock);
+		DRM_ERROR("No available AIE partition.\n");
+		return -ENODEV;
+	}
+
+	data = kmalloc(sizeof(struct aie_work_data), GFP_KERNEL);
+	if (!data) {
+		mutex_unlock(&zdev->aie_lock);
+		DRM_ERROR("Can not allocate memory,\n");
+		return -ENOMEM;
+	}
+	data->zdev = zdev;
+
+	/*
+	 * Per the requrirement of current AIE driver, we
+	 * need to release the partition in a separate thread.
+	 */
+	INIT_WORK(&data->work, zocl_aie_reset_work);
+	queue_work(zdev->aie->wq, &data->work);
+
+	/* Make sure the reset thread is done */
+	flush_workqueue(zdev->aie->wq);
+	kfree(data);
+
+	req.partition_id = zdev->aie->partition_id;
+	req.uid = zdev->aie->uid;
+
+	/* Check if AIE partition is available in a given time */
+	count = 0;
+	while (1) {
+		aie_available = aie_partition_is_available(&req);
+		if (aie_available)
+			break;
+		count++;
+		if (count == ZOCL_AIE_RESET_TIMEOUT_NUMBER) {
+			mutex_unlock(&zdev->aie_lock);
+			DRM_ERROR("AIE Reset fail: timeout.");
+			return -ETIME;
+		}
+		msleep(ZOCL_AIE_RESET_TIMEOUT_INTERVAL);
+	}
+
+	zdev->aie->aie_dev = NULL;
+	zdev->aie->aie_reset = true;
+	zdev->aie->err.num = 0;
+
+	mutex_unlock(&zdev->aie_lock);
+
+	return 0;
+}
+
+int zocl_aie_freqscale(struct drm_zocl_dev *zdev, void *data)
+{
+	struct drm_zocl_aie_freq_scale *args= data;
+	int ret = 0;
+
+	mutex_lock(&zdev->aie_lock);
+
+	if (!zdev->aie) {
+		mutex_unlock(&zdev->aie_lock);
+		DRM_ERROR("AIE image is not loaded.\n");
+		return -ENODEV;
+	}
+
+	if (!zdev->aie->aie_dev) {
+		mutex_unlock(&zdev->aie_lock);
+		DRM_ERROR("No available AIE partition.\n");
+		return -ENODEV;
+	}
+
+	if (zdev->aie->partition_id != args->partition_id) {
+		mutex_unlock(&zdev->aie_lock);
+		DRM_ERROR("AIE partition %d does not exist.\n",
+		    args->partition_id);
+		return -ENODEV;
+	}
+
+	if(!args->dir) {
+		// Read frequency from requested aie partition
+		ret = aie_partition_get_freq(zdev->aie->aie_dev, &args->freq);
+		mutex_unlock(&zdev->aie_lock);
+		if(ret)
+			DRM_ERROR("Reading clock frequency from AIE partition(%d) failed with error %d\n",
+				args->partition_id, ret);
+		return ret;
+	} else {
+		// Send Set frequency request for aie partition
+		ret = aie_partition_set_freq_req(zdev->aie->aie_dev, args->freq);
+		mutex_unlock(&zdev->aie_lock);
+		if(ret)
+			DRM_ERROR("Setting clock frequency for AIE partition(%d) failed with error %d\n",
+				args->partition_id, ret);
+		return ret;
+
+	}
+}
+
+int
+zocl_aie_graph_alloc_context(struct drm_zocl_dev *zdev, u32 gid, u32 ctx_code,
+	struct sched_client_ctx *client)
+{
+	struct list_head *cptr, *gptr;
+	struct zocl_graph_ctx_node *gnode;
+	struct sched_client_ctx *ctx;
+	unsigned long ctx_flags, graph_flags;
+	int ret;
+
+	spin_lock_irqsave(&zdev->exec->ctx_list_lock, ctx_flags);
+
+	list_for_each(cptr, &zdev->exec->ctx_list) {
+		ctx = list_entry(cptr, struct sched_client_ctx, link);
+
+		spin_lock_irqsave(&ctx->graph_list_lock, graph_flags);
+
+		list_for_each(gptr, &ctx->graph_list) {
+			gnode = list_entry(gptr, struct zocl_graph_ctx_node,
+			    link);
+
+			if (gnode->gid != gid)
+				continue;
+
+			if (ctx == client) {
+				/*
+				 * This graph has been opened by same
+				 * context.
+				 */
+				DRM_ERROR("Graph %d has been opened.\n", gid);
+				ret = -EINVAL;
+				goto out;
+			}
+
+			if (gnode->ctx_code == ZOCL_CTX_EXCLUSIVE ||
+			    ctx_code == ZOCL_CTX_EXCLUSIVE) {
+				/*
+				 * This graph has been opened with
+				 * exclusive context or;
+				 * We request exclusive context but
+				 * this graph has been opened with
+				 * non-exclusive context
+				 */
+				DRM_ERROR("Graph %d only one exclusive context can be opened.\n",
+				    gid);
+				ret = -EBUSY;
+				goto out;
+			}
+
+			if (gnode->ctx_code == ZOCL_CTX_PRIMARY &&
+			    ctx_code != ZOCL_CTX_SHARED) {
+				/*
+				 * This graph has been opened with
+				 * primary context but the request
+				 * is not shared context
+				 */
+				DRM_ERROR("Graph %d has been opened with primary context.\n",
+				    gid);
+				ret = -EBUSY;
+				goto out;
+			}
+		}
+		spin_unlock_irqrestore(&ctx->graph_list_lock, graph_flags);
+	}
+
+	gnode = kzalloc(sizeof(*gnode), GFP_KERNEL);
+	gnode->ctx_code = ctx_code;
+	gnode->gid = gid;
+	list_add_tail(&gnode->link, &client->graph_list);
+
+	spin_unlock_irqrestore(&zdev->exec->ctx_list_lock, ctx_flags);
+	return 0;
+
+out:
+	spin_unlock_irqrestore(&ctx->graph_list_lock, graph_flags);
+	spin_unlock_irqrestore(&zdev->exec->ctx_list_lock, ctx_flags);
+
+	return ret;
+}
+
+int
+zocl_aie_graph_free_context(struct drm_zocl_dev *zdev, u32 gid,
+	struct sched_client_ctx *client)
+{
+	struct list_head *gptr, *next;
+	struct zocl_graph_ctx_node *gnode;
+	unsigned long flags = 0;
+	int ret;
+
+	spin_lock_irqsave(&client->graph_list_lock, flags);
+
+	list_for_each_safe(gptr, next, &client->graph_list) {
+		gnode = list_entry(gptr, struct zocl_graph_ctx_node, link);
+
+		if (gnode->gid == gid) {
+			list_del(gptr);
+			kfree(gnode);
+			ret = 0;
+			goto out;
+		}
+	}
+
+	DRM_ERROR("Fail to close graph context: Graph %d does not exist.\n",
+	    gid);
+	ret = -EINVAL;
+
+out:
+	spin_unlock_irqrestore(&client->graph_list_lock, flags);
+	return ret;
+}
+
+void
+zocl_aie_graph_free_context_all(struct drm_zocl_dev *zdev,
+	struct sched_client_ctx *client)
+{
+	struct list_head *gptr, *next;
+	struct zocl_graph_ctx_node *gnode;
+	unsigned long flags = 0;
+
+	spin_lock_irqsave(&client->graph_list_lock, flags);
+
+	list_for_each_safe(gptr, next, &client->graph_list) {
+		gnode = list_entry(gptr, struct zocl_graph_ctx_node, link);
+
+		list_del(gptr);
+		kfree(gnode);
+	}
+
+	spin_unlock_irqrestore(&client->graph_list_lock, flags);
+}
+
+int
+zocl_aie_alloc_context(struct drm_zocl_dev *zdev, u32 ctx_code,
+	struct sched_client_ctx *client)
+{
+	struct list_head *cptr;
+	struct sched_client_ctx *ctx;
+	unsigned long ctx_flags;
+	int ret;
+
+	spin_lock_irqsave(&zdev->exec->ctx_list_lock, ctx_flags);
+
+	if (client->aie_ctx != ZOCL_CTX_NOOPS) {
+		DRM_ERROR("Changing AIE context is not supported.\n");
+		ret = -EBUSY;
+		goto out;
+	}
+
+	list_for_each(cptr, &zdev->exec->ctx_list) {
+		ctx = list_entry(cptr, struct sched_client_ctx, link);
+
+		if (ctx == client || ctx->aie_ctx == ZOCL_CTX_NOOPS)
+			continue;
+
+		if (ctx->aie_ctx == ZOCL_CTX_EXCLUSIVE ||
+		    ctx_code == ZOCL_CTX_EXCLUSIVE) {
+			/*
+			 * This AIE array has been allocated exclusive
+			 * context or;
+			 * We request exclusive context but this AIE array
+			 * has been allocated with non-exclusive context
+			 */
+			DRM_ERROR("Only one exclusive AIE context can be allocated.\n");
+			ret = -EBUSY;
+			goto out;
+		}
+
+		if (ctx->aie_ctx == ZOCL_CTX_PRIMARY &&
+		    ctx_code != ZOCL_CTX_SHARED) {
+			/*
+			 * This AIE array has been allocated primary context
+			 * but the request is not shared context
+			 */
+			DRM_ERROR("Primary AIE context has been allocated.\n");
+			ret = -EBUSY;
+			goto out;
+		}
+	}
+
+	client->aie_ctx = ctx_code;
+
+	spin_unlock_irqrestore(&zdev->exec->ctx_list_lock, ctx_flags);
+	return 0;
+
+out:
+	spin_unlock_irqrestore(&zdev->exec->ctx_list_lock, ctx_flags);
+	return ret;
+}
+
+int
+zocl_aie_free_context(struct drm_zocl_dev *zdev,
+	struct sched_client_ctx *client)
+{
+	unsigned long ctx_flags;
+
+	spin_lock_irqsave(&zdev->exec->ctx_list_lock, ctx_flags);
+
+	if (client->aie_ctx == ZOCL_CTX_NOOPS) {
+		DRM_ERROR("No AIE context has been allocated.\n");
+		spin_unlock_irqrestore(&zdev->exec->ctx_list_lock, ctx_flags);
+		return -EINVAL;
+	}
+
+	client->aie_ctx = ZOCL_CTX_NOOPS;
+
+	spin_unlock_irqrestore(&zdev->exec->ctx_list_lock, ctx_flags);
+
+	return 0;
+}
+
+int
+zocl_aie_kds_add_graph_context(struct drm_zocl_dev *zdev, u32 gid,
+	u32 ctx_code, struct kds_client *client)
+{
+	struct list_head *cptr, *gptr;
+	struct zocl_graph_ctx_node *gnode;
+	struct kds_client *ctx;
+	unsigned long graph_flags;
+	struct kds_sched *kds = &zdev->kds;
+	int ret;
+
+	mutex_lock(&kds->lock);
+
+	list_for_each(cptr, &kds->clients) {
+		ctx = list_entry(cptr, struct kds_client, link);
+
+		spin_lock_irqsave(&ctx->graph_list_lock, graph_flags);
+
+		list_for_each(gptr, &ctx->graph_list) {
+			gnode = list_entry(gptr, struct zocl_graph_ctx_node,
+			    link);
+
+			if (gnode->gid != gid)
+				continue;
+
+			if (ctx == client) {
+				/*
+				 * This graph has been opened by same
+				 * context.
+				 */
+				DRM_ERROR("Graph %d has been opened.\n", gid);
+				ret = -EINVAL;
+				goto out;
+			}
+
+			if (gnode->ctx_code == ZOCL_CTX_EXCLUSIVE ||
+			    ctx_code == ZOCL_CTX_EXCLUSIVE) {
+				/*
+				 * This graph has been opened with
+				 * exclusive context or;
+				 * We request exclusive context but
+				 * this graph has been opened with
+				 * non-exclusive context
+				 */
+				DRM_ERROR("Graph %d only one exclusive context can be opened.\n",
+				    gid);
+				ret = -EBUSY;
+				goto out;
+			}
+
+			if (gnode->ctx_code == ZOCL_CTX_PRIMARY &&
+			    ctx_code != ZOCL_CTX_SHARED) {
+				/*
+				 * This graph has been opened with
+				 * primary context but the request
+				 * is not shared context
+				 */
+				DRM_ERROR("Graph %d has been opened with primary context.\n",
+				    gid);
+				ret = -EBUSY;
+				goto out;
+			}
+		}
+		spin_unlock_irqrestore(&ctx->graph_list_lock, graph_flags);
+	}
+
+	gnode = kzalloc(sizeof(*gnode), GFP_KERNEL);
+	gnode->ctx_code = ctx_code;
+	gnode->gid = gid;
+	list_add_tail(&gnode->link, &client->graph_list);
+
+	mutex_unlock(&kds->lock);
+	return 0;
+
+out:
+	spin_unlock_irqrestore(&ctx->graph_list_lock, graph_flags);
+	mutex_unlock(&kds->lock);
+
+	return ret;
+}
+
+int
+zocl_aie_kds_del_graph_context(struct drm_zocl_dev *zdev, u32 gid,
+	struct kds_client *client)
+{
+	struct list_head *gptr, *next;
+	struct zocl_graph_ctx_node *gnode;
+	unsigned long flags = 0;
+	int ret;
+
+	spin_lock_irqsave(&client->graph_list_lock, flags);
+
+	list_for_each_safe(gptr, next, &client->graph_list) {
+		gnode = list_entry(gptr, struct zocl_graph_ctx_node, link);
+
+		if (gnode->gid == gid) {
+			list_del(gptr);
+			kfree(gnode);
+			ret = 0;
+			goto out;
+		}
+	}
+
+	DRM_ERROR("Fail to close graph context: Graph %d does not exist.\n",
+	    gid);
+	ret = -EINVAL;
+
+out:
+	spin_unlock_irqrestore(&client->graph_list_lock, flags);
+	return ret;
+}
+
+void
+zocl_aie_kds_del_graph_context_all(struct kds_client *client)
+{
+	struct list_head *gptr, *next;
+	struct zocl_graph_ctx_node *gnode;
+	unsigned long flags = 0;
+
+	spin_lock_irqsave(&client->graph_list_lock, flags);
+
+	list_for_each_safe(gptr, next, &client->graph_list) {
+		gnode = list_entry(gptr, struct zocl_graph_ctx_node, link);
+
+		list_del(gptr);
+		kfree(gnode);
+	}
+
+	spin_unlock_irqrestore(&client->graph_list_lock, flags);
+}
+
+int
+zocl_aie_kds_add_context(struct drm_zocl_dev *zdev, u32 ctx_code,
+	struct kds_client *client)
+{
+	struct list_head *cptr;
+	struct kds_client *ctx;
+	struct kds_sched *kds = &zdev->kds;
+	int ret = 0;
+
+	mutex_lock(&kds->lock);
+
+	if (client->aie_ctx != ZOCL_CTX_NOOPS) {
+		DRM_ERROR("Changing AIE context is not supported.\n");
+		ret = -EBUSY;
+		goto out;
+	}
+
+	list_for_each(cptr, &kds->clients) {
+		ctx = list_entry(cptr, struct kds_client, link);
+
+		if (ctx == client || ctx->aie_ctx == ZOCL_CTX_NOOPS)
+			continue;
+
+		if (ctx->aie_ctx == ZOCL_CTX_EXCLUSIVE ||
+		    ctx_code == ZOCL_CTX_EXCLUSIVE) {
+			/*
+			 * This AIE array has been allocated exclusive
+			 * context or;
+			 * We request exclusive context but this AIE array
+			 * has been allocated with non-exclusive context
+			 */
+			DRM_ERROR("Only one exclusive AIE context can be allocated.\n");
+			ret = -EBUSY;
+			goto out;
+		}
+
+		if (ctx->aie_ctx == ZOCL_CTX_PRIMARY &&
+		    ctx_code != ZOCL_CTX_SHARED) {
+			/*
+			 * This AIE array has been allocated primary context
+			 * but the request is not shared context
+			 */
+			DRM_ERROR("Primary AIE context has been allocated.\n");
+			ret = -EBUSY;
+			goto out;
+		}
+	}
+
+	client->aie_ctx = ctx_code;
+
+out:
+	mutex_unlock(&kds->lock);
+	return ret;
+}
+
+int
+zocl_aie_kds_del_context(struct drm_zocl_dev *zdev, struct kds_client *client)
+{
+	struct kds_sched *kds = &zdev->kds;
+
+	mutex_lock(&kds->lock);
+
+	if (client->aie_ctx == ZOCL_CTX_NOOPS) {
+		DRM_ERROR("No AIE context has been allocated.\n");
+		mutex_unlock(&kds->lock);
+		return -EINVAL;
+	}
+
+	client->aie_ctx = ZOCL_CTX_NOOPS;
+
+	mutex_unlock(&kds->lock);
+	return 0;
+
+}
+
+int
+zocl_aie_getcmd_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	int ret;
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct aie_info *aie = zdev->aie_information;
+	struct aie_info_cmd *acmd;
+	struct drm_zocl_aie_cmd *kdata = data;
+
+	if(aie == NULL)
+		return -EAGAIN;
+
+	/* If no command, the process who calls this ioctl will block here */
+	mutex_lock(&aie->aie_lock);
+	while (list_empty(&aie->aie_cmd_list)) {
+		mutex_unlock(&aie->aie_lock);
+		/*
+ 		 * Return greater than 0 if condition true before timeout,
+ 		 * 0 when time out, else -ERESTARTSYS.
+ 		 */
+		ret = wait_event_interruptible_timeout(aie->aie_wait_queue,
+		    !list_empty(&aie->aie_cmd_list), msecs_to_jiffies(500));
+		if (ret <= 0) {
+			return -ERESTARTSYS;
+                }
+		mutex_lock(&aie->aie_lock);
+	}
+
+	acmd = list_first_entry(&aie->aie_cmd_list, struct aie_info_cmd,
+	    aiec_list);
+	list_del(&acmd->aiec_list);
+
+	/* Only one aied thread */
+	aie->cmd_inprogress = acmd;
+	mutex_unlock(&aie->aie_lock);
+
+	kdata->opcode = acmd->aiec_packet->opcode;
+
+	return 0;
+}
+int
+zocl_aie_putcmd_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct aie_info *aie = zdev->aie_information;
+	struct aie_info_cmd *acmd;
+	struct drm_zocl_aie_cmd *kdata = data;
+	struct aie_info_packet *cmd;
+
+	if(aie == NULL)
+		return -EAGAIN;
+
+	mutex_lock(&aie->aie_lock);
+	acmd = aie->cmd_inprogress;
+	mutex_unlock(&aie->aie_lock);
+	if (!acmd) {
+		return -ENOMEM;
+	}
+
+	cmd = acmd->aiec_packet;
+	cmd->size = (kdata->size < AIE_INFO_SIZE) ? kdata->size : AIE_INFO_SIZE;
+	snprintf(cmd->info, cmd->size, "%s", (char *)kdata->info);
+
+	up(&acmd->aiec_sem);
+
+	return 0;
+}
+
+int
+zocl_init_aie(struct drm_zocl_dev *zdev)
+{
+	struct aie_info *aie;
+	aie = vzalloc(sizeof(struct aie_info));
+	if (!aie) {
+		zdev->aie_information = NULL;
+		return -ENOMEM;
+	}
+
+	mutex_init(&aie->aie_lock);
+	INIT_LIST_HEAD(&aie->aie_cmd_list);
+	init_waitqueue_head(&aie->aie_wait_queue);
+	aie->cmd_inprogress = NULL;
+	zdev->aie_information = aie;
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_bo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_bo.c
@@ -0,0 +1,1327 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *    Jan Stephan  <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/pagemap.h>
+#include <linux/of_address.h>
+#include <linux/iommu.h>
+#include <linux/version.h>
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0))
+#include <linux/dma-buf-map.h>
+#endif
+#include <asm/io.h>
+#include "xrt_drv.h"
+#include "zocl_drv.h"
+#include "xclbin.h"
+#include "zocl_bo.h"
+
+static inline void __user *to_user_ptr(u64 address)
+{
+	return (void __user *)(uintptr_t)address;
+}
+
+void zocl_describe(const struct drm_zocl_bo *obj)
+{
+	size_t size_in_kb = obj->cma_base.base.size / 1024;
+	size_t physical_addr = obj->cma_base.paddr;
+
+	DRM_DEBUG("%px: H[0x%zxKB] D[0x%zx]\n",
+			obj,
+			size_in_kb,
+			physical_addr);
+}
+
+static inline void
+zocl_bo_describe(const struct drm_zocl_bo *bo, uint64_t *size, uint64_t *paddr)
+{
+	if (bo->flags & (ZOCL_BO_FLAGS_CMA | ZOCL_BO_FLAGS_USERPTR)) {
+		*size = (uint64_t)bo->cma_base.base.size;
+		*paddr = (uint64_t)bo->cma_base.paddr;
+	} else {
+		*size = (uint64_t)bo->gem_base.size;
+		*paddr = (uint64_t)bo->mm_node->start;
+	}
+}
+
+int zocl_iommu_map_bo(struct drm_device *dev, struct drm_zocl_bo *bo)
+{
+	int prot = IOMMU_READ | IOMMU_WRITE;
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	size_t bo_size = bo->gem_base.size;
+	ssize_t err;
+
+	/* Create scatter gather list from user's pages */
+#if LINUX_VERSION_CODE <= KERNEL_VERSION(5, 9, 0)
+	bo->sgt = drm_prime_pages_to_sg(bo->pages, bo_size >> PAGE_SHIFT);
+#else
+	bo->sgt = drm_prime_pages_to_sg(dev, bo->pages, bo_size >> PAGE_SHIFT);
+#endif
+	if (IS_ERR(bo->sgt)) {
+		bo->uaddr = 0;
+		return PTR_ERR(bo->sgt);
+	}
+
+	/* MAP user's VA to pages table into IOMMU */
+	err = iommu_map_sg(zdev->domain, bo->uaddr, bo->sgt->sgl,
+			bo->sgt->nents, prot);
+	if (err < 0) {
+		/* If IOMMU map failed forget user's VA */
+		bo->uaddr = 0;
+		DRM_ERROR("Failed to map buffer through IOMMU: %zd\n", err);
+		return err;
+	}
+	return 0;
+}
+
+int zocl_iommu_unmap_bo(struct drm_device *dev, struct drm_zocl_bo *bo)
+{
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	/* If IOMMU map had failed before bo->uaddr will be zero */
+	if (bo->uaddr)
+		iommu_unmap(zdev->domain, bo->uaddr, bo->gem_base.size);
+	return 0;
+}
+
+static struct drm_zocl_bo *zocl_create_userprt_bo(struct drm_device *dev,
+		uint64_t unaligned_size)
+{
+	size_t size = PAGE_ALIGN(unaligned_size);
+	struct drm_gem_cma_object *cma_obj;
+	int err = 0;
+
+	if (!size)
+		return ERR_PTR(-EINVAL);
+
+	cma_obj = kzalloc(sizeof(*cma_obj), GFP_KERNEL);
+	if (!cma_obj) {
+		DRM_DEBUG("cma object create failed\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+	cma_obj->base.funcs = &zocl_gem_object_funcs;
+#endif
+	err = drm_gem_object_init(dev, &cma_obj->base, size);
+	if (err) {
+		DRM_DEBUG("drm gem object initial failed\n");
+		goto out1;
+	}
+
+	cma_obj->sgt   = NULL;
+	cma_obj->vaddr = NULL;
+	cma_obj->paddr = 0x0;
+
+	return to_zocl_bo(&cma_obj->base);
+out1:
+	kfree(cma_obj);
+	return NULL;
+}
+
+void zocl_free_userptr_bo(struct drm_gem_object *gem_obj)
+{
+	/* Do all drm_gem_cma_free_object(bo->base) do, execpt free vaddr */
+	struct drm_zocl_bo *zocl_bo = to_zocl_bo(gem_obj);
+
+	DRM_DEBUG("%s: obj 0x%px", __func__, zocl_bo);
+	if (zocl_bo->cma_base.sgt)
+		sg_free_table(zocl_bo->cma_base.sgt);
+
+	drm_gem_object_release(gem_obj);
+
+	kfree(&zocl_bo->cma_base);
+}
+
+static struct drm_zocl_bo *
+zocl_create_cma_mem(struct drm_device *dev, size_t size)
+{
+	struct drm_gem_cma_object *cma_obj;
+	struct drm_zocl_bo *bo;
+
+	/* Allocate from CMA buffer */
+	cma_obj = drm_gem_cma_create(dev, size);
+	if (IS_ERR(cma_obj))
+		return ERR_PTR(-ENOMEM);
+
+	bo = to_zocl_bo(&cma_obj->base);
+
+	return bo;
+}
+
+/*
+ * This function allocates memory from the range allocator.
+ * Also try to allocate memory from the similer memory types.
+ *
+ * @param       zdev:   zocl device structure
+ * @param       size:	requested memory size
+ * @param       mem:	requested zocl memory structure
+ *
+ * @return	bo pointer on success, error code on failure
+ */
+static struct drm_zocl_bo *
+zocl_create_range_mem(struct drm_device *dev, size_t size, struct zocl_mem *mem)
+{
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct drm_zocl_bo *bo = NULL;
+	struct zocl_mem *head_mem = mem;
+	int err = -ENOMEM;
+
+	bo = kzalloc(sizeof(struct drm_zocl_bo), GFP_KERNEL);
+	if (IS_ERR(bo))
+		return ERR_PTR(-ENOMEM);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+	bo->gem_base.funcs = &zocl_gem_object_funcs;
+#endif
+	err = drm_gem_object_init(dev, &bo->gem_base, size);
+	if (err) {
+		kfree(bo);
+		return ERR_PTR(err);
+	}
+
+	bo->mm_node = kzalloc(sizeof(struct drm_mm_node),
+			GFP_KERNEL);
+	if (IS_ERR(bo->mm_node)) {
+		drm_gem_object_release(&bo->gem_base);
+		kfree(bo);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	mutex_lock(&zdev->mm_lock);
+	do {
+		if (mem->zm_type == ZOCL_MEM_TYPE_CMA) {
+			struct drm_zocl_bo *cma_bo =
+				zocl_create_cma_mem(dev, size);
+			if (!IS_ERR(cma_bo)) {
+				/* Get the memory from CMA memory region */
+				mutex_unlock(&zdev->mm_lock);
+				kfree(bo->mm_node);
+				drm_gem_object_release(&bo->gem_base);
+				kfree(bo);
+				cma_bo->flags |= ZOCL_BO_FLAGS_CMA;
+				return cma_bo;
+			}
+			DRM_WARN("Memory allocated from CMA region"
+				" whereas requested for reserved memory region\n");
+		}
+		else {
+			err = drm_mm_insert_node_in_range(zdev->zm_drm_mm,
+				bo->mm_node, size, PAGE_SIZE, 0,
+				mem->zm_base_addr,
+				mem->zm_base_addr + mem->zm_size, 0);
+			if (!err) {
+				/* Got memory from this Range memory manager */
+				break;
+			}
+		}
+
+		/* No memory left to this memory manager.
+		 * Try to allocate from similer memory manger link list
+		 */
+		mem = list_entry(mem->zm_list.next, typeof(*mem), zm_list);
+
+	} while (&mem->zm_list != &head_mem->zm_list);
+
+	if (err) {
+		DRM_ERROR("Fail to allocate BO: size %ld\n",
+				(long)size);
+		mutex_unlock(&zdev->mm_lock);
+		kfree(bo->mm_node);
+		drm_gem_object_release(&bo->gem_base);
+		kfree(bo);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	mutex_unlock(&zdev->mm_lock);
+
+	/*
+	 * Set up a kernel mapping for direct BO access.
+	 * We don't have to fail BO allocation if we can
+	 * not establish the kernel mapping. We just can not
+	 * access BO directly from kernel.
+	 */
+	bo->vmapping = memremap(bo->mm_node->start, size, MEMREMAP_WC);
+
+	err = drm_gem_create_mmap_offset(&bo->gem_base);
+	if (err) {
+		DRM_ERROR("Fail to create BO mmap offset.\n");
+		zocl_free_bo(&bo->gem_base);
+		return ERR_PTR(err);
+	}
+
+	return bo;
+}
+
+/*
+ * This function returns zocl memory for the given memory index.
+ * Memory index is a pair of slot id and bank id.
+ *
+ * @param       zdev:    	zocl device structure
+ * @param       mem_index: 	memory index
+ *
+ * @return	memory pointer on success, NULL on failure
+ */
+static struct zocl_mem *
+zocl_get_mem_by_mem_index(struct drm_zocl_dev *zdev, u32 mem_index)
+{
+	struct zocl_mem *curr_mem = NULL;
+	list_for_each_entry(curr_mem, &zdev->zm_list_head, link)
+		if (curr_mem->zm_mem_idx == mem_index)
+			return curr_mem;
+
+	return NULL;
+}
+
+/* This function returns zocl memory for the given slot based on a
+ * specific memory topology
+ *
+ * @param       zdev:		zocl device structure
+ * @param       md:		memory topology structure
+ * @param       slot_idx:	slot index
+ *
+ * @return	memory pointer on success, NULL on failure
+ */
+static struct zocl_mem *
+zocl_get_memp_by_mem_data(struct drm_zocl_dev *zdev,
+		     struct mem_data *md, u32 slot_idx)
+{
+	struct zocl_mem *memp = NULL;
+
+	/* Create a link list for similar memory manager for this slot */
+	list_for_each_entry(memp, &zdev->zm_list_head, link) {
+		if (GET_SLOT_INDEX(memp->zm_mem_idx) != slot_idx)
+		    continue;
+
+		if ((memp->zm_base_addr == md->m_base_address) &&
+		    (memp->zm_size == md->m_size * 1024))
+			return memp;
+	}
+
+	return NULL;
+}
+
+static struct drm_zocl_bo *
+zocl_create_bo(struct drm_device *dev, uint64_t unaligned_size, u32 user_flags)
+{
+	size_t size = PAGE_ALIGN(unaligned_size);
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct drm_zocl_bo *bo = NULL;
+	int err = 0;
+
+	if (!size)
+		return ERR_PTR(-EINVAL);
+
+	if (zdev->domain) {
+		bo = kzalloc(sizeof(*bo), GFP_KERNEL);
+		if (!bo)
+			return ERR_PTR(-ENOMEM);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+		bo->gem_base.funcs = &zocl_gem_object_funcs;
+#endif
+		err = drm_gem_object_init(dev, &bo->gem_base, size);
+		if (err < 0)
+			goto free;
+	} else if (user_flags & ZOCL_BO_FLAGS_CMA) {
+		bo = zocl_create_cma_mem(dev, size);
+	} else {
+		/* We are allocating from a separate mem Index, i.e. PL-DDR or LPDDR */
+		unsigned int mem_index = GET_MEM_INDEX(user_flags);
+		struct zocl_mem *mem = zocl_get_mem_by_mem_index(zdev, mem_index);
+		if (mem == NULL)
+			return ERR_PTR(-ENOMEM);
+
+		if (!mem->zm_used || mem->zm_type != ZOCL_MEM_TYPE_RANGE_ALLOC)
+			return ERR_PTR(-EINVAL);
+
+		bo = zocl_create_range_mem(dev, size, mem);
+	}
+
+	if (user_flags & ZOCL_BO_FLAGS_EXECBUF) {
+		bo->flags = ZOCL_BO_FLAGS_EXECBUF;
+		bo->metadata.state = DRM_ZOCL_EXECBUF_STATE_ABORT;
+	}
+
+	return bo;
+free:
+	kfree(bo);
+	return ERR_PTR(err);
+}
+
+static struct drm_zocl_bo *
+zocl_create_svm_bo(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_create_bo *args = data;
+	struct drm_zocl_bo *bo = NULL;
+	size_t bo_size = 0;
+	int ret = 0;
+
+	if ((args->flags & ZOCL_BO_FLAGS_COHERENT) ||
+			(args->flags & ZOCL_BO_FLAGS_CMA))
+		return ERR_PTR(-EINVAL);
+
+	args->flags |= ZOCL_BO_FLAGS_SVM;
+	if (!(args->flags & ZOCL_BO_FLAGS_SVM))
+		return ERR_PTR(-EINVAL);
+
+	bo = zocl_create_bo(dev, args->size, args->flags);
+	bo->flags |= ZOCL_BO_FLAGS_SVM;
+	bo->mem_index = GET_MEM_INDEX(args->flags);
+
+	if (IS_ERR(bo)) {
+		DRM_DEBUG("object creation failed\n");
+		return bo;
+	}
+	bo->pages = drm_gem_get_pages(&bo->gem_base);
+	if (IS_ERR(bo->pages)) {
+		ret = PTR_ERR(bo->pages);
+		goto out_free;
+	}
+
+	bo_size = bo->gem_base.size;
+#if LINUX_VERSION_CODE <= KERNEL_VERSION(5, 9, 0)
+	bo->sgt = drm_prime_pages_to_sg(bo->pages, bo_size >> PAGE_SHIFT);
+#else
+	bo->sgt = drm_prime_pages_to_sg(dev, bo->pages, bo_size >> PAGE_SHIFT);
+#endif
+	if (IS_ERR(bo->sgt))
+		goto out_free;
+
+	bo->vmapping = vmap(bo->pages, bo->gem_base.size >> PAGE_SHIFT, VM_MAP,
+			pgprot_writecombine(PAGE_KERNEL));
+
+	if (!bo->vmapping) {
+		ret = -ENOMEM;
+		goto out_free;
+	}
+
+	ret = drm_gem_create_mmap_offset(&bo->gem_base);
+	if (ret < 0)
+		goto out_free;
+
+	ret = drm_gem_handle_create(filp, &bo->gem_base, &args->handle);
+	if (ret < 0)
+		goto out_free;
+
+	zocl_describe(bo);
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(&bo->gem_base);
+
+	/* Update memory usage statistics */
+	zocl_update_mem_stat(dev->dev_private, args->size, 1, bo->mem_index);
+
+	return bo;
+
+out_free:
+	zocl_free_bo(&bo->gem_base);
+	return ERR_PTR(ret);
+}
+
+int
+zocl_create_bo_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	int ret = 0;
+	struct drm_zocl_create_bo *args = data;
+	struct drm_zocl_bo *bo = NULL;
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct zocl_mem *mem = NULL;
+	unsigned int mem_index = 0;
+	uint32_t user_flags = args->flags;
+
+	args->flags = zocl_convert_bo_uflags(args->flags);
+
+	if (zdev->domain) {
+		bo = zocl_create_svm_bo(dev, data, filp);
+		if (IS_ERR(bo))
+			return PTR_ERR(bo);
+		bo->user_flags = user_flags;
+		return 0;
+	}
+
+	mem_index = GET_MEM_INDEX(args->flags);
+	mem = zocl_get_mem_by_mem_index(zdev, mem_index);
+
+	/* Always allocate EXECBUF from CMA */
+	if (args->flags & ZOCL_BO_FLAGS_EXECBUF)
+		args->flags |= ZOCL_BO_FLAGS_CMA;
+	else {
+		/*
+		 * For specified valid DDR bank, we only mark CMA flags
+		 * if the bank type is CMA, non-CMA type bank will use
+		 * PL-DDR; For any other cases (invalid bank index), we
+		 * allocate from CMA by default.
+		 */
+		if (mem && mem->zm_used) {
+			if (mem->zm_type == ZOCL_MEM_TYPE_CMA)
+				args->flags |= ZOCL_BO_FLAGS_CMA;
+		} else {
+			DRM_WARN("Allocating BO from CMA for invalid or unused memory index[%d]\n",
+					mem_index);
+			args->flags |= ZOCL_BO_FLAGS_CMA;
+		}
+	}
+
+	if (!(args->flags & ZOCL_BO_FLAGS_CACHEABLE)) {
+		/* If cacheable is not set, make sure we set COHERENT. */
+		args->flags |= ZOCL_BO_FLAGS_COHERENT;
+	} else if (!(args->flags & ZOCL_BO_FLAGS_CMA)) {
+		/*
+		 * We do not support allocating cacheable BO from PL-DDR or
+		 * LPDDR
+		 */
+		DRM_WARN("Cache is not supported and turned off for PL-DDR or LPDDR\n");
+		args->flags &= ~ZOCL_BO_FLAGS_CACHEABLE;
+	}
+
+	bo = zocl_create_bo(dev, args->size, args->flags);
+	if (IS_ERR(bo)) {
+		DRM_DEBUG("object creation failed\n");
+		return PTR_ERR(bo);
+	}
+
+	bo->mem_index = mem_index;
+	if (args->flags & ZOCL_BO_FLAGS_CACHEABLE)
+		bo->flags |= ZOCL_BO_FLAGS_CACHEABLE;
+	else
+		bo->flags |= ZOCL_BO_FLAGS_COHERENT;
+
+	if (args->flags & ZOCL_BO_FLAGS_CMA) {
+		bo->flags |= ZOCL_BO_FLAGS_CMA;
+		ret = drm_gem_handle_create(filp, &bo->cma_base.base,
+		    &args->handle);
+		if (ret) {
+			drm_gem_cma_free_object(&bo->cma_base.base);
+			DRM_DEBUG("handle creation failed\n");
+			return ret;
+		}
+	} else {
+		ret = drm_gem_handle_create(filp, &bo->gem_base,
+		    &args->handle);
+		if (ret) {
+			zocl_free_bo(&bo->gem_base);
+			DRM_DEBUG("handle create failed\n");
+			return ret;
+		}
+	}
+
+	bo->user_flags = user_flags;
+	zocl_describe(bo);
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(&bo->cma_base.base);
+
+	/*
+	 * Update memory usage statistics.
+	 *
+	 * Note: We can not use args->size here because it is
+	 *       the required size while gem object records the
+	 *       actual size allocated.
+	 */
+	zocl_update_mem_stat(zdev, bo->gem_base.size, 1, bo->mem_index);
+
+	return ret;
+}
+
+int
+zocl_userptr_bo_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	int ret = 0;
+	struct drm_zocl_bo *bo = NULL;
+	unsigned int page_count = 0;
+	struct drm_zocl_userptr_bo *args = data;
+	struct page **pages = NULL;
+	unsigned int sg_count = 0;
+	uint32_t user_flags = args->flags;
+
+	if (offset_in_page(args->addr)) {
+		DRM_ERROR("User ptr not PAGE aligned\n");
+		return -EINVAL;
+	}
+
+	if (user_flags & ZOCL_BO_FLAGS_EXECBUF) {
+		DRM_ERROR("Exec buf could not be a user buffer\n");
+		return -EINVAL;
+	}
+
+	bo = zocl_create_userprt_bo(dev, args->size);
+	if (IS_ERR(bo)) {
+		DRM_ERROR("Object creation failed\n");
+		return PTR_ERR(bo);
+	}
+
+	/* For accurately account for number of pages */
+	page_count = bo->cma_base.base.size >> PAGE_SHIFT;
+
+	pages = kvmalloc_array(page_count, sizeof(*pages), GFP_KERNEL);
+	if (!pages) {
+		ret = -ENOMEM;
+		goto out1;
+	}
+
+	ret = get_user_pages_fast(args->addr, page_count, 1, pages);
+	if (ret != page_count) {
+		DRM_ERROR("Unable to get user pages\n");
+		ret = -ENOMEM;
+		goto out0;
+	}
+
+#if LINUX_VERSION_CODE <= KERNEL_VERSION(5, 9, 0)
+	bo->cma_base.sgt = drm_prime_pages_to_sg(pages, page_count);
+#else
+	bo->cma_base.sgt = drm_prime_pages_to_sg(dev, pages, page_count);
+#endif
+	if (IS_ERR(bo->cma_base.sgt)) {
+		ret = PTR_ERR(bo->cma_base.sgt);
+		goto out0;
+	}
+
+	sg_count = dma_map_sg(dev->dev, bo->cma_base.sgt->sgl,
+				bo->cma_base.sgt->nents, 0);
+	if (sg_count <= 0) {
+		DRM_ERROR("Map SG list failed\n");
+		ret = -ENOMEM;
+		goto out0;
+	}
+
+	bo->cma_base.paddr = sg_dma_address((bo->cma_base.sgt)->sgl);
+
+	/* Physical address must be continuous */
+	if (sg_count != 1) {
+		DRM_WARN("User buffer is not physical contiguous\n");
+		ret = -EINVAL;
+		goto out0;
+	}
+
+	bo->cma_base.vaddr = (void *)(uintptr_t)args->addr;
+
+	ret = drm_gem_handle_create(filp, &bo->cma_base.base, &args->handle);
+	if (ret) {
+		ret = -EINVAL;
+		DRM_ERROR("Handle creation failed\n");
+		goto out0;
+	}
+
+	bo->flags |= ZOCL_BO_FLAGS_USERPTR;
+
+	bo->user_flags = user_flags;
+	zocl_describe(bo);
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(&bo->cma_base.base);
+
+	kvfree(pages);
+
+	return ret;
+
+out0:
+	kvfree(pages);
+out1:
+	zocl_free_userptr_bo(&bo->cma_base.base);
+	DRM_DEBUG("handle creation failed\n");
+	return ret;
+}
+
+struct drm_zocl_bo *zocl_drm_create_bo(struct drm_device *dev,
+					  uint64_t unaligned_size,
+					  unsigned user_flags)
+{
+	return zocl_create_bo(dev, unaligned_size, user_flags);
+}
+
+int zocl_map_bo_ioctl(struct drm_device *dev,
+		void *data,
+		struct drm_file *filp)
+{
+	int ret = 0;
+	struct drm_zocl_map_bo *args = data;
+	struct drm_gem_object *gem_obj = NULL;
+
+	gem_obj = zocl_gem_object_lookup(dev, filp, args->handle);
+	if (!gem_obj) {
+		DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
+		return -EINVAL;
+	}
+
+	if (zocl_bo_userptr(to_zocl_bo(gem_obj))) {
+		ret = -EPERM;
+		goto out;
+	}
+
+	/* The mmap offset was set up at BO allocation time. */
+	args->offset = drm_vma_node_offset_addr(&gem_obj->vma_node);
+	zocl_describe(to_zocl_bo(gem_obj));
+
+out:
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(gem_obj);
+	return ret;
+}
+
+int zocl_sync_bo_ioctl(struct drm_device *dev,
+		void *data,
+		struct drm_file *filp)
+{
+	const struct drm_zocl_sync_bo	*args = data;
+	struct drm_gem_object		*gem_obj;
+	struct drm_gem_cma_object	*cma_obj;
+	struct drm_zocl_bo		*bo;
+	dma_addr_t			bus_addr;
+	int				rc = 0;
+
+	gem_obj = zocl_gem_object_lookup(dev, filp, args->handle);
+	if (!gem_obj) {
+		DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
+		return -EINVAL;
+	}
+
+	if ((args->offset > gem_obj->size) || (args->size > gem_obj->size) ||
+			((args->offset + args->size) > gem_obj->size)) {
+		rc = -EINVAL;
+		goto out;
+	}
+
+	bo = to_zocl_bo(gem_obj);
+	if (bo->flags & ZOCL_BO_FLAGS_COHERENT) {
+		/* The CMA buf is coherent, we don't need to do anything */
+		rc = 0;
+		goto out;
+	}
+
+	cma_obj = to_drm_gem_cma_obj(gem_obj);
+	bus_addr = cma_obj->paddr;
+
+	/* only invalidate the range of addresses requested by the user */
+	bus_addr += args->offset;
+
+	/**
+	 * NOTE: We a little bit abuse the dma_sync_single_* API here because
+	 *       it is documented as for the DMA buffer mapped by dma_map_*
+	 *       API. The buffer we are syncing here is mapped through
+	 *       remap_pfn_range(). But so far this is our best choice
+	 *       and it works.
+	 */
+	if (args->dir == DRM_ZOCL_SYNC_BO_TO_DEVICE) {
+		dma_sync_single_for_device(dev->dev, bus_addr, args->size,
+		    DMA_TO_DEVICE);
+	} else if (args->dir == DRM_ZOCL_SYNC_BO_FROM_DEVICE) {
+		dma_sync_single_for_cpu(dev->dev, bus_addr, args->size,
+		    DMA_FROM_DEVICE);
+	} else
+		rc = -EINVAL;
+
+out:
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(gem_obj);
+
+	return rc;
+}
+
+bool
+zocl_can_dma_performed(struct drm_device *dev, struct drm_file *filp,
+	struct drm_zocl_copy_bo *args, uint64_t *dst_paddr, uint64_t *src_paddr)
+{
+	struct drm_gem_object  *dst_gem_obj, *src_gem_obj;
+	struct drm_zocl_bo     *dst_bo, *src_bo;
+	uint64_t               dst_size, src_size;
+	int                    unsupported_flags = 0;
+	bool                   rc = true;
+
+	dst_gem_obj = zocl_gem_object_lookup(dev, filp, args->dst_handle);
+	if (!dst_gem_obj) {
+		DRM_ERROR("Failed to look up GEM dst handle %d\n",
+		    args->dst_handle);
+		return false;
+	}
+
+	src_gem_obj = zocl_gem_object_lookup(dev, filp, args->src_handle);
+	if (!src_gem_obj) {
+		DRM_ERROR("Failed to look up GEM src handle %d\n",
+		    args->src_handle);
+		rc = false;
+		goto out;
+	}
+
+	dst_bo = to_zocl_bo(dst_gem_obj);
+	src_bo = to_zocl_bo(src_gem_obj);
+	unsupported_flags = (ZOCL_BO_FLAGS_USERPTR | ZOCL_BO_FLAGS_HOST_BO |
+		ZOCL_BO_FLAGS_SVM);
+	if ((dst_bo->flags & unsupported_flags) ||
+	    (src_bo->flags & unsupported_flags)) {
+		DRM_ERROR("Failed: Not supported dst flags 0x%x and "
+		    "src flags 0x%x\n", dst_bo->flags, src_bo->flags);
+		rc = false;
+		goto out;
+	}
+
+	zocl_bo_describe(dst_bo, &dst_size, dst_paddr);
+	zocl_bo_describe(src_bo, &src_size, src_paddr);
+
+	/*
+	 * pre check before requesting DMA memory copy.
+	 *    dst_offset + size <= dst_size
+	 *    src_offset + size <= src_size`
+	 */
+	if (args->size == 0) {
+		DRM_ERROR("Failed: request size cannot be ZERO!");
+		rc = false;
+		goto out;
+	}
+	if (args->dst_offset + args->size > dst_size) {
+		DRM_ERROR("Failed: dst_offset + size out of boundary");
+		rc = false;
+		goto out;
+	}
+	if (args->src_offset + args->size > src_size) {
+		DRM_ERROR("Failed: src_offset + size out of boundary");
+		rc = false;
+		goto out;
+	}
+
+out:
+	if (dst_gem_obj)
+		ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(dst_gem_obj);
+
+	if (src_gem_obj)
+		ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(src_gem_obj);
+
+	return rc;
+}
+
+int zocl_dma_channel_instance(zocl_dma_handle_t *dma_handle,
+			      struct drm_zocl_dev *zdev)
+{
+	dma_cap_mask_t dma_mask;
+
+	if (!dma_handle->dma_chan && ZOCL_PLATFORM_ARM64) {
+		/* If zdev_dma_chan is NULL, we haven't initialized it yet. */
+		if (!zdev->zdev_dma_chan) {
+			dma_cap_zero(dma_mask);
+			dma_cap_set(DMA_MEMCPY, dma_mask);
+			zdev->zdev_dma_chan =
+			    dma_request_channel(dma_mask, 0, NULL);
+			if (!zdev->zdev_dma_chan) {
+				DRM_WARN("no DMA Channel available.\n");
+				return -EBUSY;
+			}
+		}
+		dma_handle->dma_chan = zdev->zdev_dma_chan;
+	}
+
+	return dma_handle->dma_chan ? 0 : -EINVAL;
+}
+
+int zocl_copy_bo_async(struct drm_device *dev,
+		struct drm_file *filp,
+		zocl_dma_handle_t *dma_handle,
+		struct drm_zocl_copy_bo *args)
+{
+	uint64_t dst_paddr, src_paddr;
+	int rc = 0;
+	bool ret = false;
+
+	if (dma_handle->dma_func == NULL) {
+		DRM_ERROR("Failed: no callback dma_func for async dma");
+		return -EINVAL;
+	}
+
+	ret = zocl_can_dma_performed(dev, filp, args, &dst_paddr, &src_paddr);
+	if (!ret) {
+		DRM_ERROR("Failed: Cannot perform DMA due to previous Errors");
+		return -EINVAL;
+	}
+
+	dst_paddr += args->dst_offset;
+	src_paddr += args->src_offset;
+
+	rc = zocl_dma_memcpy_pre(dma_handle, (dma_addr_t)dst_paddr,
+	    (dma_addr_t)src_paddr, (size_t)args->size);
+	if (!rc)
+		zocl_dma_start(dma_handle);
+
+	return rc;
+}
+
+int zocl_info_bo_ioctl(struct drm_device *dev,
+		void *data,
+		struct drm_file *filp)
+{
+	const struct drm_zocl_bo *bo;
+	struct drm_zocl_info_bo *args = data;
+	struct drm_gem_object *gem_obj = zocl_gem_object_lookup(dev, filp,
+			args->handle);
+
+	if (!gem_obj) {
+		DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
+		return -EINVAL;
+	}
+
+	bo = to_zocl_bo(gem_obj);
+	zocl_bo_describe(bo, &args->size, &args->paddr);
+	args->flags = bo->user_flags;
+
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(gem_obj);
+
+	return 0;
+}
+
+static int zocl_bo_rdwr_ioctl(struct drm_device *dev, void *data,
+			      struct drm_file *filp, bool is_read)
+{
+	const struct drm_zocl_pwrite_bo *args = data;
+	struct drm_gem_object *gem_obj = zocl_gem_object_lookup(dev, filp,
+								args->handle);
+	char __user *user_data = to_user_ptr(args->data_ptr);
+	struct drm_zocl_bo *bo;
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0))
+	struct dma_buf_map map;
+#endif
+	int ret = 0;
+	char *kaddr;
+
+	if (!gem_obj) {
+		DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
+		return -EINVAL;
+	}
+
+	if ((args->offset > gem_obj->size) || (args->size > gem_obj->size)
+	    || ((args->offset + args->size) > gem_obj->size)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (args->size == 0) {
+		ret = 0;
+		goto out;
+	}
+	if (!ZOCL_ACCESS_OK(VERIFY_READ, user_data, args->size)) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	bo = to_zocl_bo(gem_obj);
+	if (bo->flags & ZOCL_BO_FLAGS_CMA) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 12, 0)
+		ret = drm_gem_cma_vmap(gem_obj, &map);
+		if(ret || dma_buf_map_is_null(&map))
+			kaddr = NULL;
+		else
+			kaddr = map.is_iomem ? map.vaddr_iomem : map.vaddr;
+#else
+		kaddr = drm_gem_cma_prime_vmap(gem_obj);
+#endif
+	}
+	else
+		kaddr = bo->vmapping;
+	if (!kaddr) {
+		DRM_ERROR("Fail to map BO %d\n", args->handle);
+		ret = -EFAULT;
+		goto out;
+	}
+
+	kaddr += args->offset;
+
+	if (is_read)
+		ret = copy_to_user(user_data, kaddr, args->size);
+	else
+		ret = copy_from_user(kaddr, user_data, args->size);
+
+out:
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(gem_obj);
+
+	return ret;
+
+}
+
+int zocl_pwrite_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp)
+{
+	return (zocl_bo_rdwr_ioctl(dev, data, filp, false));
+}
+
+int zocl_pread_bo_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp)
+{
+	return (zocl_bo_rdwr_ioctl(dev, data, filp, true));
+}
+
+static struct drm_gem_cma_object *
+zocl_cma_create(struct drm_device *dev, size_t size)
+{
+	struct drm_gem_cma_object *cma_obj;
+	struct drm_gem_object *gem_obj;
+	int ret;
+
+	gem_obj = kzalloc(sizeof(struct drm_zocl_bo), GFP_KERNEL);
+	if (!gem_obj) {
+		DRM_ERROR("cma_create: alloc failed\n");
+		return ERR_PTR(-ENOMEM);
+	}
+	cma_obj = container_of(gem_obj, struct drm_gem_cma_object, base);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+	gem_obj->funcs = &zocl_cma_default_funcs;
+#endif
+
+	ret = drm_gem_object_init(dev, gem_obj, size);
+	if (ret) {
+		DRM_ERROR("cma_create: gem_obj_init failed\n");
+		goto error;
+	}
+
+	ret = drm_gem_create_mmap_offset(gem_obj);
+	if (ret) {
+		DRM_ERROR("cma_create: gem_mmap_offset failed\n");
+		drm_gem_object_release(gem_obj);
+		goto error;
+	}
+
+	return cma_obj;
+
+error:
+	kfree(cma_obj);
+	return ERR_PTR(ret);
+}
+
+int zocl_get_hbo_ioctl(struct drm_device *dev, void *data,
+		       struct drm_file *filp)
+{
+	struct drm_zocl_bo *bo;
+	struct drm_zocl_host_bo *args = data;
+	struct drm_gem_cma_object *cma_obj;
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	u64 host_mem_start = zdev->host_mem;
+	u64 host_mem_end = zdev->host_mem + zdev->host_mem_len;
+	int ret;
+
+	if (args->size == 0) {
+		DRM_ERROR("get_hbo: Buffer size must be greater than zero\n");
+		return -EINVAL;
+	}
+	if (!(host_mem_start <= args->paddr &&
+	   args->paddr < host_mem_end &&
+	   args->size <= host_mem_end - args->paddr)) {
+		DRM_ERROR("get_hbo: Buffer at out side of reserved memory region\n");
+		return -ENOMEM;
+	}
+	if (!PAGE_ALIGNED(args->paddr) || !PAGE_ALIGNED(args->size)) {
+		/* DRM requirement */
+		DRM_ERROR("get_hbo: Buffer paddr & size must be page aligned to page_size. paddr: 0x%llx, size: 0x%lx\n", args->paddr, args->size);
+		return -EINVAL;
+	}
+
+	cma_obj = zocl_cma_create(dev, args->size);
+	if (IS_ERR(cma_obj))
+		return -ENOMEM;
+
+	cma_obj->paddr = args->paddr;
+	cma_obj->vaddr = memremap(args->paddr, args->size, MEMREMAP_WB);
+	if (!cma_obj->vaddr) {
+		DRM_ERROR("get_hbo: failed to allocate buffer with size %zu\n",
+			  args->size);
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	bo = to_zocl_bo(&cma_obj->base);
+
+	bo->flags |= ZOCL_BO_FLAGS_HOST_BO;
+	bo->flags |= ZOCL_BO_FLAGS_CMA;
+
+	ret = drm_gem_handle_create(filp, &bo->cma_base.base, &args->handle);
+	if (ret) {
+		drm_gem_cma_free_object(&bo->cma_base.base);
+		DRM_ERROR("get_hbo: gem handle creation failed\n");
+		return ret;
+	}
+
+	zocl_describe(bo);
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(&bo->cma_base.base);
+
+	return ret;
+error:
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(&cma_obj->base);
+	return ret;
+}
+
+void zocl_free_host_bo(struct drm_gem_object *gem_obj)
+{
+	struct drm_zocl_bo *zocl_bo = to_zocl_bo(gem_obj);
+
+	DRM_DEBUG("%s: obj 0x%px", __func__, zocl_bo);
+
+	memunmap(zocl_bo->cma_base.vaddr);
+
+	drm_gem_object_release(gem_obj);
+
+	kfree(&zocl_bo->cma_base);
+}
+
+/*
+ * Update the memory usage of by BO.
+ *
+ * count is the number of BOs being allocated/freed. If count > 0, we are
+ * allocating 'count' BOs with total size 'size'; If count < 0, we are
+ * freeing 'count' BOs with total size 'size'.
+ */
+void zocl_update_mem_stat(struct drm_zocl_dev *zdev, u64 size, int count,
+		uint32_t index)
+{
+	struct zocl_mem *mem = zocl_get_mem_by_mem_index(zdev, index);
+	if (!mem)
+		return;
+
+	/*
+	 * If the 'bank' passed in is a valid bank and its type is
+	 * PL-DDR or LPDDR , we update that bank usage. Otherwise, we go
+	 * through our bank list and find the CMA bank to update
+	 * its usage.
+	 */
+	if (mem->zm_type != ZOCL_MEM_TYPE_RANGE_ALLOC) {
+		struct zocl_mem *curr_mem = NULL;
+		list_for_each_entry(curr_mem, &zdev->zm_list_head, link) {
+			if (curr_mem->zm_used &&
+			    curr_mem->zm_type == ZOCL_MEM_TYPE_CMA) {
+				mem = curr_mem;
+				break;
+			}
+		}
+	}
+
+	write_lock(&zdev->attr_rwlock);
+	mem->zm_stat.memory_usage +=
+	    (count > 0) ?  size : -size;
+	mem->zm_stat.bo_count += count;
+	write_unlock(&zdev->attr_rwlock);
+}
+
+/* This function return True if given region is reserved
+ * on device tree. Else return False
+ */
+static bool check_for_reserved_memory(uint64_t start_addr, size_t size)
+{
+	struct device_node *mem_np;
+	struct device_node *np_it;
+	struct resource res_mem;
+	int err;
+
+	mem_np = of_find_node_by_name(NULL, "reserved-memory");
+	if(!mem_np)
+		return false;
+
+	/* Traverse through all the child nodes */
+	for (np_it = NULL; (np_it = of_get_next_child(mem_np, np_it)) != NULL;) {
+		err = of_address_to_resource(np_it, 0, &res_mem);
+		if (!err) {
+			/* Check the given address and size fall
+			 * in this reserved memory region
+			 */
+			if (start_addr >= res_mem.start &&
+					size <= resource_size(&res_mem)) {
+				of_node_put(mem_np);
+				return true;
+			}
+		}
+	}
+
+	of_node_put(mem_np);
+	return false;
+}
+
+
+/*
+ * Initialize the memory structure in zocl driver based on the memory
+ * topology extracted from xclbin.
+ *
+ * Currently, we could have multiple memory sections but only two type
+ * of them could be marked as used. We identify the memory type by its
+ * tag. If the tag field contains "MIG", it is PL-DDR. Tag filed LPDDR
+ * for higher order LPDDR memory. Other tags e.g. "HP", "HPC", it is
+ * CMA memory.
+ *
+ * PL-DDR and LPDDR are managed by DRM MM Range Allocator;
+ * CMA is managed by DRM CMA Allocator.
+ *
+ * @param       zdev:    zocl device structure
+ * @param       slot:  	 slot specific structure
+ *
+ */
+void zocl_init_mem(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot)
+{
+	struct zocl_mem *memp = NULL;
+	struct mem_topology *mtopo = slot->topology;
+	uint64_t mm_start_addr = 0;
+	uint64_t mm_end_addr = 0;
+	int i, j;
+
+	if (!mtopo)
+		return;
+
+	mutex_lock(&zdev->mm_lock);
+	/* Initialize with max and min possible value */
+	mm_start_addr = 0xffffFFFFffffFFFF;
+	mm_end_addr = 0;
+
+	for (i = 0; i < mtopo->m_count; i++) {
+		struct mem_data *md = &mtopo->m_mem_data[i];
+
+		memp = vzalloc(sizeof(struct zocl_mem));
+		if (md->m_type == MEM_STREAMING) {
+			memp->zm_type = ZOCL_MEM_TYPE_STREAMING;
+			continue;
+		}
+
+		memp->zm_base_addr = md->m_base_address;
+		/* In mem_topology, size is in KB */
+		memp->zm_size = md->m_size * 1024;
+		memp->zm_used = md->m_used;
+		memp->zm_mem_idx = SET_MEM_INDEX(slot->slot_idx, i);
+		/* This list used for multiple tag case */
+		INIT_LIST_HEAD(&memp->zm_list);
+
+		list_add_tail(&memp->link, &zdev->zm_list_head);
+
+		if (!check_for_reserved_memory(memp->zm_base_addr,
+					       memp->zm_size)) {
+			DRM_INFO("Memory %d is not reserved in device tree."
+					" Will allocate memory from CMA\n", i);
+			memp->zm_type = ZOCL_MEM_TYPE_CMA;
+			continue;
+		}
+
+                /* Update the start and end address for the memory manager */
+                if (memp->zm_base_addr < mm_start_addr)
+                        mm_start_addr = memp->zm_base_addr;
+                if ((memp->zm_base_addr + memp->zm_size) > mm_end_addr)
+                        mm_end_addr = memp->zm_base_addr + memp->zm_size;
+
+		memp->zm_type = ZOCL_MEM_TYPE_RANGE_ALLOC;
+	}
+
+	/* Initialize drm memory manager if not yet done */
+	if (!zdev->zm_drm_mm) {
+		/* Initialize a single drm memory manager for whole memory
+		 * available for this device.
+		 */
+		zdev->zm_drm_mm = vzalloc(sizeof(struct drm_mm));
+		drm_mm_init(zdev->zm_drm_mm, mm_start_addr,
+			    (mm_end_addr - mm_start_addr));
+	}
+
+	/* Create a link list for similar memory manager for this slot */
+	for (i = 0; i < mtopo->m_count; i++) {
+		struct mem_data *md = &mtopo->m_mem_data[i];
+		if (!md->m_used)
+			continue;
+
+		memp = zocl_get_memp_by_mem_data(zdev, md, slot->slot_idx);
+		if (!memp) {
+			DRM_ERROR("Failed to get the memoory\n");
+			mutex_unlock(&zdev->mm_lock);
+			return;
+		}
+
+		for (j = 0; j < mtopo->m_count; j++) {
+			struct zocl_mem *tmp_memp;
+			if ((i == j) || !mtopo->m_mem_data[j].m_used)
+				continue;
+
+			tmp_memp = zocl_get_memp_by_mem_data(zdev,
+					&mtopo->m_mem_data[j],
+					slot->slot_idx);
+			if (strcmp(mtopo->m_mem_data[i].m_tag,
+				   mtopo->m_mem_data[j].m_tag) &&
+			    list_empty(&tmp_memp->zm_list)) {
+				list_add_tail(&memp->zm_list,
+					      &tmp_memp->zm_list);
+				memp = tmp_memp;
+			}
+		}
+	}
+
+	mutex_unlock(&zdev->mm_lock);
+}
+
+/*
+ * Clean the memories for a specific slot. Other memory remain unchanged.
+ * This will not delete the memory manager.
+ *
+ * @param       zdev:		zocl device structure
+ * @param       slot_idx:	slot index
+ *
+ */
+void zocl_clear_mem_slot(struct drm_zocl_dev *zdev, u32 slot_idx)
+{
+	struct zocl_mem *curr_mem = NULL;
+	struct zocl_mem *next = NULL;
+
+	mutex_lock(&zdev->mm_lock);
+	if (list_empty(&zdev->zm_list_head))
+		goto done;
+
+	list_for_each_entry_safe(curr_mem, next, &zdev->zm_list_head, link) {
+		if (slot_idx != GET_SLOT_INDEX(curr_mem->zm_mem_idx))
+			continue;
+
+		list_del(&curr_mem->link);
+		vfree(curr_mem);
+	}
+
+done:
+	mutex_unlock(&zdev->mm_lock);
+}
+
+/*
+ * Clean all the memories for a specific device. This will also delete
+ * the memory manager.
+ *
+ * @param       zdev:	zocl device structure
+ *
+ */
+void zocl_clear_mem(struct drm_zocl_dev *zdev)
+{
+	struct zocl_mem *curr_mem = NULL;
+	struct zocl_mem *next = NULL;
+
+	mutex_lock(&zdev->mm_lock);
+
+	list_for_each_entry_safe(curr_mem, next, &zdev->zm_list_head, link) {
+		list_del(&curr_mem->link);
+		vfree(curr_mem);
+	}
+
+	/* clean up a drm_mm allocator. Free the memory */
+	if (zdev->zm_drm_mm) {
+		drm_mm_takedown(zdev->zm_drm_mm);
+		vfree(zdev->zm_drm_mm);
+	}
+
+	mutex_unlock(&zdev->mm_lock);
+}
+
+struct drm_gem_object *zocl_gem_import(struct drm_device *dev,
+				       struct dma_buf *dma_buf)
+{
+	struct drm_gem_object *gem_obj;
+	struct drm_zocl_bo *zocl_bo;
+
+	gem_obj = drm_gem_prime_import(dev, dma_buf);
+	if (!IS_ERR(gem_obj)) {
+		zocl_bo = to_zocl_bo(gem_obj);
+		/* drm_gem_cma_prime_import_sg_table() is used for hook
+		 * gem_prime_import_sg_table. It will check if import buffer
+		 * is a CMA buffer and create CMA object.
+		 */
+		zocl_bo->flags |= ZOCL_BO_FLAGS_CMA;
+	}
+
+	return gem_obj;
+}
+
+void zocl_drm_free_bo(struct drm_zocl_bo *bo)
+{
+	zocl_free_bo(&bo->gem_base);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_csr_intc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_csr_intc.c
@@ -0,0 +1,202 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include "zocl_lib.h"
+#include "zocl_ert_intc.h"
+
+#define WORD_BITS			32
+/* ERT INTC driver name. */
+#define ZINTC_NAME			"zocl_csr_intc"
+/* The CSR IP provided 128 bit status. */
+#define ZINTC_MAX_VECTORS		128
+/* Every 32 status bits requires one irq */
+#define ZINTC_MAX_IRQS			(ZINTC_MAX_VECTORS / WORD_BITS)
+
+#define ZINTC2PDEV(zintc)		((zintc)->zei_pdev)
+#define ZINTC2DEV(zintc)		(&ZINTC2PDEV(zintc)->dev)
+#define zintc_err(zintc, fmt, args...)	zocl_err(ZINTC2DEV(zintc), fmt"\n", ##args)
+#define zintc_info(zintc, fmt, args...)	zocl_info(ZINTC2DEV(zintc), fmt"\n", ##args)
+#define zintc_dbg(zintc, fmt, args...)	zocl_dbg(ZINTC2DEV(zintc), fmt"\n", ##args)
+
+struct zocl_csr_intc {
+	struct platform_device		*zei_pdev;
+	int				zei_num_irqs;
+	u32				zei_irqs[ZINTC_MAX_IRQS];
+	struct zocl_ert_intc_status_reg	*zei_status;
+
+	spinlock_t			zei_lock;
+	struct zocl_ert_intc_handler	zei_handler[ZINTC_MAX_VECTORS];
+};
+
+static inline void reg_write(void __iomem  *addr, u32 val)
+{
+	iowrite32(val, addr);
+}
+
+static inline u32 reg_read(void __iomem *addr)
+{
+	return ioread32(addr);
+}
+
+static irqreturn_t zintc_isr(int irq, void *arg)
+{
+	unsigned long irqflags;
+	const u32 lastbit = 0x1;
+	int word_idx, i;
+	u32 intr;
+	struct zocl_csr_intc *zintc = (struct zocl_csr_intc *)arg;
+	struct zocl_ert_intc_handler *h;
+
+	spin_lock_irqsave(&zintc->zei_lock, irqflags);
+	/* Find out status word based on irq. */
+	for (word_idx = 0; word_idx < zintc->zei_num_irqs; word_idx++) {
+		if (zintc->zei_irqs[word_idx] == irq)
+			break;
+	}
+	BUG_ON(word_idx >= zintc->zei_num_irqs);
+
+	intr = reg_read(&zintc->zei_status->zeisr_status[i]);
+	for (i = word_idx * WORD_BITS; i < (word_idx + 1) * WORD_BITS && intr; i++, intr >>= 1) {
+		if ((intr & lastbit) == 0) 
+			continue;
+		h = &zintc->zei_handler[i];
+		if (h->zeih_cb && h->zeih_enabled)
+			h->zeih_cb(i, h->zeih_arg);
+		else
+			zintc_err(zintc, "Spurious interrupt received on %d", i); 
+	}
+	spin_unlock_irqrestore(&zintc->zei_lock, irqflags);
+	return IRQ_HANDLED;
+}
+
+static int zintc_probe(struct platform_device *pdev)
+{
+	int ret;
+	int i;
+	struct zocl_csr_intc *zintc = NULL;
+	int num_irqs = platform_irq_count(pdev);
+
+	if (num_irqs <= 0 || num_irqs > ZINTC_MAX_IRQS) {
+		zocl_err(&pdev->dev, "invalid num of IRQ: %d\n", num_irqs); 
+		return -EINVAL;
+	}
+
+	zintc = devm_kzalloc(&pdev->dev, sizeof(*zintc), GFP_KERNEL);
+	if (!zintc)
+		return -ENOMEM;
+	zintc->zei_pdev = pdev;
+	zintc->zei_num_irqs = num_irqs;
+	spin_lock_init(&zintc->zei_lock);
+	platform_set_drvdata(pdev, zintc);
+
+	zintc->zei_status = zlib_map_res_by_name(pdev, ZEI_RES_STATUS, NULL, NULL);
+	if (!zintc->zei_status) {
+		zintc_err(zintc, "failed to find INTC Status registers"); 
+		return -EINVAL;
+	}
+	/* Disable interrupt till we are ready to handle it. */
+	reg_write(&zintc->zei_status->zeisr_enable, 0);
+
+	for (i = 0; i < num_irqs; i++) {
+		struct resource *res = platform_get_resource(pdev, IORESOURCE_IRQ, i);
+		u32 irq = res->start;
+
+		zintc->zei_irqs[i] = irq;
+		ret = devm_request_irq(&pdev->dev, irq, zintc_isr, 0, ZINTC_NAME, zintc);
+		if (ret)
+			zintc_err(zintc, "failed to add isr for IRQ: %d: %d", irq, ret); 
+		else
+			zintc_info(zintc, "managing IRQ %d", irq); 
+	}
+
+	for (i = 0; i < ZINTC_MAX_VECTORS; i++) {
+		struct zocl_ert_intc_handler *h = &zintc->zei_handler[i];
+
+		h->zeih_pdev = pdev;
+		h->zeih_irq = zintc->zei_irqs[i / WORD_BITS];
+	}
+
+	/* Ready to turn on interrupts! */
+	reg_write(&zintc->zei_status->zeisr_enable, 1);
+	return 0;
+}
+
+static int zintc_remove(struct platform_device *pdev)
+{
+	struct zocl_csr_intc *zintc = platform_get_drvdata(pdev);
+
+	zintc_info(zintc, "Removing %s", ZINTC_NAME);
+	return 0;
+}
+
+/*
+ * Interfaces exposed to other subdev drivers.
+ */
+
+static void zocl_csr_intc_add(struct platform_device *pdev, u32 id, irq_handler_t cb, void *arg)
+{
+	unsigned long irqflags;
+	struct zocl_csr_intc *zintc = platform_get_drvdata(pdev);
+	struct zocl_ert_intc_handler *h;
+
+	BUG_ON(id >= ZINTC_MAX_VECTORS);
+
+	spin_lock_irqsave(&zintc->zei_lock, irqflags);
+
+	h = &zintc->zei_handler[id];
+	if (h->zeih_irq == 0)
+		zintc_err(zintc, "vector %d has no matching irq", id);
+
+	BUG_ON(h->zeih_cb);
+	h->zeih_cb = cb;
+	h->zeih_arg = arg;
+	h->zeih_enabled = true;
+
+	spin_unlock_irqrestore(&zintc->zei_lock, irqflags);
+}
+
+static void zocl_csr_intc_remove(struct platform_device *pdev, u32 id)
+{
+	unsigned long irqflags;
+	struct zocl_csr_intc *zintc = platform_get_drvdata(pdev);
+	struct zocl_ert_intc_handler *h;
+
+	BUG_ON(id >= ZINTC_MAX_VECTORS);
+	spin_lock_irqsave(&zintc->zei_lock, irqflags);
+
+	h = &zintc->zei_handler[id];
+	h->zeih_cb = NULL;
+	h->zeih_arg = NULL;
+	h->zeih_enabled = false;
+
+	spin_unlock_irqrestore(&zintc->zei_lock, irqflags);
+}
+
+static struct zocl_ert_intc_drv_data zocl_csr_intc_drvdata = {
+	.add = zocl_csr_intc_add,
+	.remove = zocl_csr_intc_remove,
+};
+
+static const struct platform_device_id zocl_csr_intc_id_match[] = {
+	{ ERT_CSR_INTC_DEV_NAME, (kernel_ulong_t)&zocl_csr_intc_drvdata },
+	{ /* end of table */ },
+};
+
+struct platform_driver zocl_csr_intc_driver = {
+	.driver = {
+		.name = ZINTC_NAME,
+	},
+	.probe  = zintc_probe,
+	.remove = zintc_remove,
+	.id_table = zocl_csr_intc_id_match,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_ctrl_ert.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_ctrl_ert.c
@@ -0,0 +1,979 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include "zocl_lib.h"
+#include "zocl_drv.h"
+#include "xrt_cu.h"
+#include "xgq_cmd_ert.h"
+#include "xgq_impl.h"
+#include "zocl_sk.h"
+#include "zocl_xgq.h"
+#include "zocl_cu_xgq.h"
+#include "zocl_ert_intc.h"
+
+/* ERT XGQ driver name. */
+#define ZERT_NAME "zocl_ctrl_ert"
+
+#define ZERT2PDEV(zert)			((zert)->zce_pdev)
+#define ZERT2DEV(zert)			(&ZERT2PDEV(zert)->dev)
+#define zert_err(zert, fmt, args...)	zocl_err(ZERT2DEV(zert), fmt"\n", ##args)
+#define zert_info(zert, fmt, args...)	zocl_info(ZERT2DEV(zert), fmt"\n", ##args)
+#define zert_dbg(zert, fmt, args...)	zocl_dbg(ZERT2DEV(zert), fmt"\n", ##args)
+
+/* Legacy ERT resources. */
+#define ZERT_HW_RES     		0
+#define ZERT_CQ_RES     		1
+
+#define ZERT_CU_DMA_ENABLE		0x18
+/*
+ * The CU_STATUS is for CU to notify PS about completion of a command.
+ */
+#define ZERT_CU_STATUS_REG		0x40
+/*
+ * The CQ_STATUS is for host to notify PS about arriving of a new command.
+ */
+#define ZERT_CQ_STATUS_REG		0x54
+/*
+ * This STATUS REGISTER is for communicating completed CQ slot indices
+ * MicroBlaze write, host reads.  MB(W) / HOST(COR). In total, there are
+ * four of them contiguously.
+ */
+#define ZERT_CMD_STATUS_REG		0x0
+/*
+ * Enable global interrupts from MB to HOST on command completion.
+ * When enabled writing to STATUS_REGISTER causes an interrupt in HOST.
+ * MB(W)
+ */
+#define ZERT_HOST_INT_ENABLE		0x100
+
+#define ERT_CQ_IRQ			0
+#define ERT_CU_IRQ			1
+
+/*
+ * CQ format version 1.0:
+ * First word on CQ is version number, followed by ctrl XGQ, which may go up to 1.5k.
+ */
+#define ZERT_CQ_FMT_VER			0x10000
+#define CTRL_XGQ_SLOT_SIZE		512
+#define MAX_CTRL_XGQ_SIZE		(1024 + 512)
+struct zocl_ert_cq_header {
+	u32			zcx_ver;
+	u32			zcx_ctrl_ring[0];
+};
+
+struct zocl_ert_cq {
+	union {
+		struct zocl_ert_cq_header	zec_header;
+		char				zec_buf[MAX_CTRL_XGQ_SIZE];
+	};
+};
+
+/* Max 128 PL kernels and 128 PS kernels. */
+#define ZERT_MAX_NUM_CU			256
+
+/* For now, hard-coded 32 CU XGQs so we only use one interrupt line. */
+#define ZERT_MAX_NUM_CU_XGQ		32
+/*
+ * Num of slots for each CU XGQ. Adding more slots will just result in
+ * more cmd sitting on HW which will not help with performance, but only
+ * waste HW resources. Using less slots may impact performance.
+ */
+#define ZERT_CU_XGQ_MAX_SLOTS		128
+#define ZERT_CU_XGQ_MIN_SLOTS		4
+
+/* Config for each CU sub-dev. */
+#define ZERT_INVALID_XGQ_ID	((u32)-1)
+struct zocl_ctrl_ert_cu {
+	u32			zcec_xgq_idx;
+	struct platform_device	*zcec_pdev;
+};
+
+/* Config for each CU XGQ sub-dev. */
+struct zocl_ctrl_ert_cu_xgq {
+	u32			zcecx_irq;
+	struct platform_device	*zcecx_intc_pdev;
+
+	// for XGQ IP access
+	resource_size_t		zcecx_xgq_reg;
+	// for triggering intr to host, if the write to tail pointer does not
+	resource_size_t		zcecx_cq_int_reg;
+
+	resource_size_t		zcecx_ring;
+	resource_size_t		zcecx_slot_size;
+	resource_size_t		zcecx_ring_size;
+	bool			zcecx_echo_mode;
+	struct platform_device	*zcecx_pdev;
+};
+
+struct zocl_ctrl_ert {
+	struct platform_device	*zce_pdev;
+
+	struct zocl_ert_cq __iomem *zce_cq;
+	size_t			zce_cq_size;
+	u64			zce_cq_start;
+	u64			zce_cu_xgq_ring_start;
+	size_t			zce_cu_xgq_ring_size;
+
+	void			*zce_ctrl_xgq_hdl;
+
+	size_t			zce_num_cu_xgqs;
+	struct zocl_ctrl_ert_cu_xgq *zce_cu_xgqs;
+
+	size_t			zce_num_cus;
+	struct zocl_ctrl_ert_cu *zce_cus;
+	resource_size_t		zce_max_cu_size;
+
+	size_t			zce_num_scus;
+	struct zocl_ctrl_ert_cu *zce_scus;
+
+	struct platform_device	*zce_xgq_intc;
+
+	bool			zce_config_completed;
+	bool			zce_echo_mode;
+};
+
+static void zert_cmd_handler(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd);
+
+static inline void reg_write(void __iomem *base, u64 off, u32 val)
+{
+	iowrite32(val, base + off);
+}
+
+static inline u32 reg_read(void __iomem *base, u64 off)
+{
+	return ioread32(base + off);
+}
+
+static void cu_conf2info(struct xgq_cmd_config_cu *conf, struct xrt_cu_info *info)
+{
+	char *kname_p = conf->name;
+
+	memset(info, 0, sizeof(*info));
+	info->num_res = 1;
+	info->addr = conf->haddr;
+	info->addr <<= 32;
+	info->addr |= conf->laddr;
+	info->size = conf->map_size;
+	info->intr_enable = 0;
+	info->intr_id = 0;
+	info->slot_idx = 0;
+	info->protocol = conf->ip_ctrl;
+	if (info->protocol == CTRL_FA)
+		info->model = XCU_FA;
+	else
+		info->model = XCU_HLS;
+	info->cu_domain = conf->cu_domain;
+	info->cu_idx = conf->cu_idx;
+	strcpy(info->kname, strsep(&kname_p, ":"));
+	strcpy(info->iname, strsep(&kname_p, ":"));
+	memcpy(info->uuid, conf->uuid, sizeof(info->uuid));
+}
+
+static int zert_create_cu(struct zocl_ctrl_ert *zert, struct xgq_cmd_config_cu *conf)
+{
+	int ret = 0;
+	struct xrt_cu_info info;
+	u32 cuidx = conf->cu_idx;
+
+	if (cuidx >= zert->zce_num_cus) {
+		zert_err(zert, "CU index (%d) is out of range", cuidx);
+		return -EINVAL;
+	}
+
+	BUG_ON(zert->zce_cus[cuidx].zcec_pdev);
+	cu_conf2info(conf, &info);
+	ret = subdev_create_cu(ZERT2DEV(zert), &info, &zert->zce_cus[cuidx].zcec_pdev);
+	if (ret) {
+		zert_err(zert, "Failed to create CU.%d device", cuidx);
+		return ret;
+	}
+
+	if (conf->payload_size > zert->zce_max_cu_size)
+		zert->zce_max_cu_size = conf->payload_size;
+
+	return 0;
+}
+
+static int zert_create_scu(struct zocl_ctrl_ert *zert, struct xgq_cmd_config_cu *conf)
+{
+	int ret = 0;
+	struct xrt_cu_info info = {0};
+	u32 cuidx = conf->cu_idx;
+
+	if (cuidx >= zert->zce_num_scus) {
+		zert_err(zert, "SCU index (%d) is out of range", cuidx);
+		return -EINVAL;
+	}
+
+	BUG_ON(zert->zce_scus[cuidx].zcec_pdev);
+	cu_conf2info(conf, &info);
+	ret = subdev_create_scu(ZERT2DEV(zert), &info, &zert->zce_scus[cuidx].zcec_pdev);
+	if (ret) {
+		zert_err(zert, "Failed to create SCU.%d device", cuidx);
+		return ret;
+	}
+
+	if (conf->payload_size > zert->zce_max_cu_size)
+		zert->zce_max_cu_size = conf->payload_size;
+
+	ret = zocl_scu_wait_ready(zert->zce_scus[cuidx].zcec_pdev);
+	if(ret) {
+		zert_err(zert, "SCU.%d failed to initialize", cuidx);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void zert_init_cus(struct zocl_ctrl_ert *zert)
+{
+	u32 i = 0;
+	struct zocl_ctrl_ert_cu *cu = &zert->zce_cus[0];
+
+	for (i = 0; i < zert->zce_num_cus; i++, cu++) {
+		cu->zcec_pdev = NULL;
+		cu->zcec_xgq_idx = ZERT_INVALID_XGQ_ID;
+	}
+
+	cu = &zert->zce_scus[0];
+
+	for (i = 0; i < zert->zce_num_scus; i++, cu++) {
+		cu->zcec_pdev = NULL;
+		cu->zcec_xgq_idx = ZERT_INVALID_XGQ_ID;
+	}
+
+}
+
+static int zert_validate_cus(struct zocl_ctrl_ert *zert)
+{
+	u32 i = 0;
+	struct zocl_ctrl_ert_cu *cu = &zert->zce_cus[0];
+
+	for (i = 0; i < zert->zce_num_cus; i++, cu++) {
+		if ((cu->zcec_pdev == NULL) && (i < zert->zce_num_cus)) {
+			zert_err(zert, "Some CUs are not configured properly.");
+			return -EINVAL;
+		}
+		if (cu->zcec_pdev && (i >= zert->zce_num_cus)) {
+			zert_err(zert, "CU index out of range");
+			return -EINVAL;
+		}
+	}
+
+	cu = &zert->zce_scus[0];
+
+	for (i = 0; i < zert->zce_num_scus; i++, cu++) {
+		if ((cu->zcec_pdev == NULL) && (i < zert->zce_num_scus)) {
+			zert_err(zert, "Some SCUs are not configured properly.");
+			return -EINVAL;
+		}
+		if (cu->zcec_pdev && (i >= zert->zce_num_scus)) {
+			zert_err(zert, "SCU index out of range");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static void zert_unassign_cu_xgqs(struct zocl_ctrl_ert *zert)
+{
+	int ret = 0;
+	u32 i = 0;
+	u32 idx = 0;
+	struct zocl_ctrl_ert_cu *cu = &zert->zce_cus[0];
+
+	for (i = 0; i < zert->zce_num_cus; i++, cu++) {
+		idx = cu->zcec_xgq_idx;
+		if (idx != ZERT_INVALID_XGQ_ID) {
+			ret = zcu_xgq_unassign_cu(zert->zce_cu_xgqs[idx].zcecx_pdev, i, 0);
+			if (ret)
+				zert_err(zert, "Failed to unassign CU %d to XGQ %d", i, idx);
+		}
+		cu->zcec_xgq_idx = ZERT_INVALID_XGQ_ID;
+	}
+
+	cu = &zert->zce_scus[0];
+
+	for (i = 0; i < zert->zce_num_scus; i++, cu++) {
+		idx = cu->zcec_xgq_idx;
+		if (idx != ZERT_INVALID_XGQ_ID) {
+			ret = zcu_xgq_unassign_cu(zert->zce_cu_xgqs[idx].zcecx_pdev, i, SCU_DOMAIN>>16);
+			if (ret)
+				zert_err(zert, "Failed to unassign SCU %d to XGQ %d", i, idx);
+		}
+		cu->zcec_xgq_idx = ZERT_INVALID_XGQ_ID;
+	}
+
+}
+
+static void zert_destroy_cus(struct zocl_ctrl_ert *zert)
+{
+	u32 i = 0;
+	struct zocl_ctrl_ert_cu *cu = &zert->zce_scus[0];
+
+	zert_unassign_cu_xgqs(zert);
+
+	// Need to remove PS kernel first before removing PL CU contexts.
+	// TO-DO: Will need to make this more robust in future
+	for (i = 0; i < zert->zce_num_scus; i++, cu++) {
+		if (cu->zcec_pdev) {
+			zocl_scu_sk_shutdown(cu->zcec_pdev);
+			zlib_destroy_subdev(cu->zcec_pdev);
+			cu->zcec_pdev = NULL;
+			BUG_ON(cu->zcec_xgq_idx != ZERT_INVALID_XGQ_ID);
+		}
+	}
+	zert->zce_num_scus = 0;
+	kfree(zert->zce_scus);
+	zert->zce_scus = NULL;
+
+	cu = &zert->zce_cus[0];
+
+	for (i = 0; i < zert->zce_num_cus; i++, cu++) {
+		if (cu->zcec_pdev) {
+			zlib_destroy_subdev(cu->zcec_pdev);
+			cu->zcec_pdev = NULL;
+			BUG_ON(cu->zcec_xgq_idx != ZERT_INVALID_XGQ_ID);
+		}
+	}
+	zert->zce_num_cus = 0;
+	zert->zce_max_cu_size = 0;
+	kfree(zert->zce_cus);
+	zert->zce_cus = NULL;
+
+}
+
+static int zert_create_cu_xgq(struct zocl_ctrl_ert *zert, struct zocl_ctrl_ert_cu_xgq *info)
+{
+	int ret, i;
+	struct resource res[10] = {};
+	struct zocl_cu_xgq_info zci = {};
+
+	i = 0;
+	fill_irq_res(&res[i++], info->zcecx_irq, ZCX_RES_IRQ);
+	// Using XGQ IP
+	if (info->zcecx_xgq_reg)
+		fill_reg_res(&res[i++], info->zcecx_xgq_reg, ZCX_RES_XGQ_IP);
+	// Legacy CQ status
+	if (info->zcecx_cq_int_reg)
+		fill_reg_res(&res[i++], info->zcecx_cq_int_reg, ZCX_RES_CQ_PROD_INT);
+	fill_iomem_res(&res[i++], info->zcecx_ring, info->zcecx_ring_size, ZCX_RES_RING);
+
+	zci.zcxi_slot_size = info->zcecx_slot_size;
+	zci.zcxi_echo_mode = info->zcecx_echo_mode;
+	zci.zcxi_intc_pdev = info->zcecx_intc_pdev;
+
+	ret = zlib_create_subdev(ZERT2DEV(zert), CU_XGQ_DEV_NAME, res, i, &zci, sizeof(zci),
+				 &info->zcecx_pdev);
+	if (ret)
+		zert_err(zert, "Failed to create %s.%d device", CU_XGQ_DEV_NAME, info->zcecx_irq);
+
+	return ret;
+}
+
+static void zert_assign_cu_xgqs(struct zocl_ctrl_ert *zert)
+{
+	int ret = 0;
+	u32 i = 0;
+	u32 idx = 0;
+	u32 xgqidx = 0;
+	struct zocl_ctrl_ert_cu *cu = &zert->zce_cus[0];
+
+	for (i = 0; i < zert->zce_num_cu_xgqs; i++) {
+		if (zert->zce_cu_xgqs[i].zcecx_pdev)
+			break;
+	}
+	if (i == zert->zce_num_cu_xgqs) {
+		zert_err(zert, "No XGQ is available");
+		return;
+	}
+
+	for (i = 0; i < zert->zce_num_cus; i++, cu++) {
+		struct platform_device *xgqpdev = NULL;
+
+		if (cu->zcec_pdev) {
+			/* Find next enabled XGQ, we are guaranteed to have one. */
+			while (xgqpdev == NULL) {
+				idx = xgqidx++ % zert->zce_num_cu_xgqs;
+				xgqpdev = zert->zce_cu_xgqs[idx].zcecx_pdev;
+			}
+
+			BUG_ON(cu->zcec_xgq_idx != ZERT_INVALID_XGQ_ID);
+			ret = zcu_xgq_assign_cu(xgqpdev, i, 0);
+			if (ret)
+				zert_err(zert, "Failed to assign CU %d to XGQ %d", i, idx);
+			else
+				cu->zcec_xgq_idx = idx;
+		}
+	}
+
+	cu = &zert->zce_scus[0];
+	for (i = 0; i < zert->zce_num_scus; i++, cu++) {
+		struct platform_device *xgqpdev = NULL;
+
+		if (cu->zcec_pdev) {
+			/* Find next enabled XGQ, we are guaranteed to have one. */
+			while (xgqpdev == NULL) {
+				idx = xgqidx++ % zert->zce_num_cu_xgqs;
+				xgqpdev = zert->zce_cu_xgqs[idx].zcecx_pdev;
+			}
+
+			BUG_ON(cu->zcec_xgq_idx != ZERT_INVALID_XGQ_ID);
+			ret = zcu_xgq_assign_cu(xgqpdev, i, SCU_DOMAIN>>16);
+			if (ret)
+				zert_err(zert, "Failed to assign CU %d to XGQ %d", i, idx);
+			else
+				cu->zcec_xgq_idx = idx;
+		}
+	}
+}
+
+static int zert_create_cu_xgqs(struct zocl_ctrl_ert *zert)
+{
+	int rc, i;
+	const u32 alignment = sizeof(u32);
+	struct zocl_ctrl_ert_cu_xgq *xcu;
+	size_t slot_sz = zert->zce_max_cu_size;
+	size_t slot_num = ZERT_CU_XGQ_MAX_SLOTS;
+	size_t xgq_ring_size;
+	size_t nxgqs;
+
+	BUG_ON(zert->zce_cu_xgq_ring_start % alignment);
+	BUG_ON(zert->zce_cu_xgq_ring_size % alignment);
+
+	/* No need to create CU XGQ if there is no CU configured. */
+	if ((zert->zce_num_cus == 0) && (zert->zce_num_scus == 0)) {
+		zert_info(zert, "No CU is configured, skip creating XGQs");
+		return 0;
+	}
+
+	/* Find out the appropriate number of slots. */
+	xgq_ring_size = xgq_ring_len(slot_num, slot_sz);
+	while (slot_num && xgq_ring_size > zert->zce_cu_xgq_ring_size) {
+		slot_num >>= 1;
+		xgq_ring_size = xgq_ring_len(slot_num, slot_sz);
+	}
+	if (slot_num < ZERT_CU_XGQ_MIN_SLOTS) {
+		zert_err(zert, "XGQ slot size is too big: %ld", slot_sz);
+		return -E2BIG;
+	}
+
+	/* Find out the appropriate number of XGQs to enable. */
+	nxgqs = zert->zce_cu_xgq_ring_size / xgq_ring_size;
+	if (nxgqs > (zert->zce_num_cus + zert->zce_num_scus))
+		nxgqs = zert->zce_num_cus + zert->zce_num_scus;
+	if (nxgqs > zert->zce_num_cu_xgqs)
+		nxgqs = zert->zce_num_cu_xgqs;
+
+	zert_info(zert, "Creating %ld XGQs (slot size 0x%lx) for %ld CUs and %ld SCUs",
+		  nxgqs, slot_sz, zert->zce_num_cus, zert->zce_num_scus);
+
+	/* Enable first nxgqs number of CU XGQs. */
+	for (i = 0; i < nxgqs; i++) {
+		xcu = &zert->zce_cu_xgqs[i];
+		xcu->zcecx_ring = zert->zce_cu_xgq_ring_start + xgq_ring_size * i;
+		xcu->zcecx_ring_size = xgq_ring_size;
+		xcu->zcecx_slot_size = slot_sz; /* All CU XGQs use the same slot size. */
+		xcu->zcecx_echo_mode = zert->zce_echo_mode;
+
+		/* intc for receiving interrupt from host. */
+		xcu->zcecx_intc_pdev = zert->zce_xgq_intc;
+
+		rc = zert_create_cu_xgq(zert, xcu);
+		if (rc) {
+			zert_err(zert, "failed to alloc CU XGQ %d: %d", i, rc);
+			break;
+		}
+	}
+
+	zert_assign_cu_xgqs(zert);
+	return rc;
+}
+
+static void zert_destroy_cu_xgqs(struct zocl_ctrl_ert *zert)
+{
+	int i;
+	struct zocl_ctrl_ert_cu_xgq *xcu;
+
+	if (zert->zce_num_cu_xgqs == 0)
+		return;
+
+	for (i = 0; i < zert->zce_num_cu_xgqs; i++) {
+		xcu = &zert->zce_cu_xgqs[i];
+		if (xcu->zcecx_pdev)
+			zlib_destroy_subdev(xcu->zcecx_pdev);
+		zert->zce_cu_xgqs[i].zcecx_pdev = NULL;
+	}
+}
+
+static int zert_versal_init(struct zocl_ctrl_ert *zert)
+{
+	int i = 0;
+	int ret = 0;
+	const char *cq_res_name = "xlnx,xgq_buffer";
+	const char *xgq_res_name = "xlnx,xgq_device";
+	struct device_node *np = NULL;
+	struct zocl_ctrl_ert_cu_xgq *cuxgq = NULL;
+	struct resource res = {};
+	u32 *irqs = NULL;
+
+	/* Obtain shared ring buffer. */
+	zert->zce_cq = zlib_map_phandle_res_by_name(ZERT2PDEV(zert), cq_res_name,
+						    &zert->zce_cq_start, &zert->zce_cq_size);
+	if (!zert->zce_cq) {
+		zert_err(zert, "failed to find ERT command queue");
+		return -EINVAL;
+	}
+
+	/* Obtain all CU XGQs. */
+	ret = of_count_phandle_with_args(ZERT2DEV(zert)->of_node, xgq_res_name, NULL);
+	if (ret <= 0) {
+		zert_err(zert, "failed to find CU XGQs");
+		return -EINVAL;
+	}
+	zert->zce_num_cu_xgqs = ret;
+	zert->zce_cu_xgqs = kzalloc(sizeof(struct zocl_ctrl_ert_cu_xgq) * ret, GFP_KERNEL);
+	if (!zert->zce_cu_xgqs)
+		return -ENOMEM;
+
+	for (i = 0; i < zert->zce_num_cu_xgqs; i++) {
+		np = of_parse_phandle(ZERT2DEV(zert)->of_node, xgq_res_name, i);
+		if (!np) {
+			zert_err(zert, "failed to find node for CU XGQ %d", i);
+			continue;
+		}
+		ret = of_address_to_resource(np, 0, &res);
+		if (ret) {
+			zert_err(zert, "failed to find res for CU XGQ %d: %d", i, ret);
+			continue;
+		}
+
+		cuxgq = &zert->zce_cu_xgqs[i];
+		cuxgq->zcecx_irq = of_irq_get(np, 0);
+		cuxgq->zcecx_xgq_reg = res.start;
+		/* Write to tail pointer will trigger interrupt. */
+		cuxgq->zcecx_cq_int_reg = 0;
+
+		zert_info(zert, "Found CU XGQ @ %pR on irq %d", &res, cuxgq->zcecx_irq);
+	}
+
+	/* Bring up XGQ INTC. */
+	irqs = kzalloc(sizeof(u32) * zert->zce_num_cu_xgqs, GFP_KERNEL);
+	if (!irqs) {
+		zert_err(zert, "Failed to alloc irq array for intc device");
+	} else {
+		for (i = 0; i < zert->zce_num_cu_xgqs; i++)
+			irqs[i] = zert->zce_cu_xgqs[i].zcecx_irq;
+		ret = zocl_ert_create_intc(ZERT2DEV(zert), irqs, i, 0, ERT_XGQ_INTC_DEV_NAME,
+					   &zert->zce_xgq_intc);
+		if (ret)
+			zert_err(zert, "Failed to create xgq intc device: %d", ret);
+	}
+
+	/* TODO: Bringup INTC sub-dev to handle interrupts for all CUs. */
+
+	/* Initialize soft kernel data structure */
+	zocl_init_soft_kernel(zocl_get_zdev());
+
+	return 0;
+}
+
+static int zert_mpsoc_init(struct zocl_ctrl_ert *zert)
+{
+	void __iomem *regs;
+	u64 reg_start = 0;
+	/* We support max 32 XGQs since we have only one interrupt line from host. */
+	const int max_xgq = 32;
+	u32 irq = 0;
+	size_t i = 0;
+	int ret = 0;
+
+	/* Obtain CSR and CQ status registers. */
+	regs = zlib_map_res_by_id(ZERT2PDEV(zert), ZERT_HW_RES, &reg_start, NULL);
+	if (!regs) {
+		zert_err(zert, "failed to find ERT registers");
+		return -EINVAL;
+	}
+	/* Obtain shared ring buffer. */
+	zert->zce_cq = zlib_map_res_by_id(ZERT2PDEV(zert), ZERT_CQ_RES,
+					  &zert->zce_cq_start, &zert->zce_cq_size);
+	if (!zert->zce_cq) {
+		zert_err(zert, "failed to find ERT command queue");
+		return -EINVAL;
+	}
+
+	/* Disable CUDMA, always. */
+	reg_write(regs, ZERT_CU_DMA_ENABLE, 0);
+	/* Enable host intr, always. */
+	reg_write(regs, ZERT_HOST_INT_ENABLE, 1);
+	/* Done with registers. */
+	devm_iounmap(ZERT2DEV(zert), regs);
+
+	/* Obtain all XGQs. */
+	zert->zce_num_cu_xgqs = max_xgq;
+	zert->zce_cu_xgqs = kzalloc(sizeof(struct zocl_ctrl_ert_cu_xgq) * zert->zce_num_cu_xgqs,
+				    GFP_KERNEL);
+	if (!zert->zce_cu_xgqs)
+		return -ENOMEM;
+	for (i = 0; i < zert->zce_num_cu_xgqs; i++) {
+		struct zocl_ctrl_ert_cu_xgq *cuxgq = &zert->zce_cu_xgqs[i];
+		cuxgq->zcecx_irq = i;
+		cuxgq->zcecx_xgq_reg = 0;
+		cuxgq->zcecx_cq_int_reg = reg_start + ZERT_CMD_STATUS_REG;
+	}
+
+	/* Bringup INTC sub-dev to handle interrupts for all CU XGQs. */
+	irq = platform_get_irq(ZERT2PDEV(zert), ERT_CQ_IRQ);
+	ret = zocl_ert_create_intc(ZERT2DEV(zert), &irq, 1, reg_start + ZERT_CQ_STATUS_REG,
+				   ERT_CSR_INTC_DEV_NAME, &zert->zce_xgq_intc);
+	if (ret)
+		zert_err(zert, "Failed to create xgq intc device: %d", ret);
+
+	/* Initialize soft kernel data structure */
+	zocl_init_soft_kernel(zocl_get_zdev());
+	
+	return 0;
+}
+
+static const struct zocl_ctrl_ert_drvdata {
+	int (*zced_dev_init)(struct zocl_ctrl_ert *zert);
+}
+zocl_ctrl_ert_drvdata_mpsoc = { zert_mpsoc_init },
+zocl_ctrl_ert_drvdata_versal = { zert_versal_init };
+
+static const struct of_device_id zocl_ctrl_ert_of_match[] = {
+	{ .compatible = "xlnx,embedded_sched", .data = &zocl_ctrl_ert_drvdata_mpsoc },
+	{ .compatible = "xlnx,embedded_sched_versal", .data = &zocl_ctrl_ert_drvdata_versal },
+	{ /* end of table */ },
+};
+
+static int zert_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	const struct of_device_id *id = NULL;
+	struct zocl_ctrl_ert_drvdata *data = NULL;
+	struct zocl_ctrl_ert *zert = devm_kzalloc(&pdev->dev, sizeof(*zert), GFP_KERNEL);
+	struct zocl_xgq_init_args xgq_arg = {};
+
+	if (!zert)
+		return -ENOMEM;
+	zert->zce_pdev = pdev;
+	platform_set_drvdata(pdev, zert);
+
+	id = of_match_node(zocl_ctrl_ert_of_match, pdev->dev.of_node);
+	data = (struct zocl_ctrl_ert_drvdata *)id->data;
+	ret = data->zced_dev_init(zert);
+	if (ret)
+		return ret;
+
+	zert->zce_cu_xgq_ring_start = zert->zce_cq_start + sizeof(struct zocl_ert_cq);
+	zert->zce_cu_xgq_ring_size = zert->zce_cq_size - sizeof(struct zocl_ert_cq);
+	/* Remap CQ to just what we need. The rest will be passed onto CU XGQ drivers. */
+	devm_iounmap(ZERT2DEV(zert), zert->zce_cq);
+	zert->zce_cq = devm_ioremap(ZERT2DEV(zert), zert->zce_cq_start, sizeof(struct zocl_ert_cq));
+	/* Init header and advertise CQ version */
+	memset_io(zert->zce_cq, 0, sizeof(struct zocl_ert_cq));
+	iowrite32(ZERT_CQ_FMT_VER, &zert->zce_cq->zec_header.zcx_ver);
+
+	/* Bringup CTRL XGQ last */
+	xgq_arg.zxia_pdev = ZERT2PDEV(zert);
+	xgq_arg.zxia_ring = zert->zce_cq->zec_header.zcx_ctrl_ring;
+	xgq_arg.zxia_ring_size = sizeof(struct zocl_ert_cq) - sizeof(struct zocl_ert_cq_header);
+	xgq_arg.zxia_ring_slot_size = CTRL_XGQ_SLOT_SIZE;
+	xgq_arg.zxia_cmd_handler = zert_cmd_handler;
+	zert->zce_ctrl_xgq_hdl = zxgq_init(&xgq_arg);
+	if (!zert->zce_ctrl_xgq_hdl)
+		zert_err(zert, "failed to initialize CTRL XGQ");
+
+	return 0;
+}
+
+static int zert_remove(struct platform_device *pdev)
+{
+	struct zocl_ctrl_ert *zert = platform_get_drvdata(pdev);
+
+	zert_info(zert, "Removing %s", ZERT_NAME);
+
+	if (zert->zce_ctrl_xgq_hdl)
+		zxgq_fini(zert->zce_ctrl_xgq_hdl);
+
+	zert_destroy_cus(zert);
+	zert_destroy_cu_xgqs(zert);
+	zocl_fini_soft_kernel(zocl_get_zdev());
+	kfree(zert->zce_cu_xgqs);
+	zert->zce_cu_xgqs = NULL;
+	zert->zce_num_cu_xgqs = 0;
+	zocl_ert_destroy_intc(zert->zce_xgq_intc);
+
+	return 0;
+}
+
+struct platform_driver zocl_ctrl_ert_driver = {
+	.driver = {
+		.name = ZERT_NAME,
+		.of_match_table = zocl_ctrl_ert_of_match,
+	},
+	.probe  = zert_probe,
+	.remove = zert_remove,
+};
+
+
+/*
+ * Control commands are handled below.
+ */
+
+#define ZERT_CMD_HANDLER_VER_MAJOR	1
+#define ZERT_CMD_HANDLER_VER_MINOR	0
+
+typedef void (*cmd_handler)(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+			    struct xgq_com_queue_entry *resp);
+
+static void init_resp(struct xgq_com_queue_entry *resp, u16 cid, u32 rcode)
+{
+	memset(resp, 0, sizeof(*resp));
+	resp->hdr.cid = cid;
+	if (rcode != 0) {
+		resp->hdr.cstate = XGQ_CMD_STATE_TIMEOUT;
+	} else
+		resp->hdr.cstate = XGQ_CMD_STATE_COMPLETED;
+	resp->rcode = rcode;
+}
+
+static void zert_cmd_identify(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+			      struct xgq_com_queue_entry *resp)
+{
+	struct xgq_cmd_resp_identify *r = (struct xgq_cmd_resp_identify *)resp;
+
+	init_resp(resp, cmd->cid, 0);
+
+	r->major = ZERT_CMD_HANDLER_VER_MAJOR;
+	r->minor = ZERT_CMD_HANDLER_VER_MINOR;
+}
+
+static void zert_cmd_cfg_start(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+			       struct xgq_com_queue_entry *resp)
+{
+	struct xgq_cmd_config_start *c = (struct xgq_cmd_config_start *)cmd;
+	struct xgq_cmd_resp_config_start *r = (struct xgq_cmd_resp_config_start *)resp;
+	struct zocl_ctrl_ert_cu *cus = NULL;
+	struct zocl_ctrl_ert_cu *scus = NULL;
+
+	if (ZERT_MAX_NUM_CU < c->num_cus) {
+		zert_err(zert, "Configuring too many CUs: %d", c->num_cus);
+		init_resp(resp, cmd->cid, -EINVAL);
+		return;
+	}
+	cus = kzalloc(sizeof(struct zocl_ctrl_ert_cu) * c->num_cus, GFP_KERNEL);
+	if (!cus) {
+		init_resp(resp, cmd->cid, -ENOMEM);
+		return;
+	}
+	if (ZERT_MAX_NUM_CU < c->num_scus) {
+		zert_err(zert, "Configuring too many SCUs: %d", c->num_scus);
+		init_resp(resp, cmd->cid, -EINVAL);
+		return;
+	}
+	scus = kzalloc(sizeof(struct zocl_ctrl_ert_cu) * c->num_scus, GFP_KERNEL);
+	if (!scus) {
+		init_resp(resp, cmd->cid, -ENOMEM);
+		return;
+	}
+
+	zert_destroy_cus(zert);
+	zert_destroy_cu_xgqs(zert);
+	kds_reset(&zocl_get_zdev()->kds);
+	zert->zce_config_completed = false;
+
+	zert->zce_cus = cus;
+	zert->zce_num_cus = c->num_cus;
+	zert->zce_scus = scus;
+	zert->zce_num_scus = c->num_scus;
+	zert->zce_echo_mode = c->echo;
+	zert_init_cus(zert);
+
+	init_resp(resp, cmd->cid, 0);
+	r->i2h = true;
+	r->i2e = true;
+	r->cui = false;
+	r->ob = false;
+}
+
+static void zert_cmd_cfg_end(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+			     struct xgq_com_queue_entry *resp)
+{
+	int rc;
+
+	if (zert->zce_config_completed) {
+		zert_err(zert, "ERT is not in config mode");
+		init_resp(resp, cmd->cid, -EINVAL);
+		return;
+	}
+	zert->zce_config_completed = true;
+
+	zocl_get_zdev()->kds.cu_intr_cap = 1;
+	zocl_get_zdev()->kds.cu_intr = 0;
+	kds_cfg_update(&zocl_get_zdev()->kds);
+
+	rc = zert_validate_cus(zert);
+	if (!rc)
+		rc = zert_create_cu_xgqs(zert);
+
+	init_resp(resp, cmd->cid, rc);
+}
+
+static void zert_cmd_default_handler(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+				     struct xgq_com_queue_entry *resp)
+{
+	zert_err(zert, "Unknown cmd: %d", cmd->opcode);
+	init_resp(resp, cmd->cid, -ENOTTY);
+}
+
+static void zert_cmd_cfg_cu(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+			    struct xgq_com_queue_entry *resp)
+{
+	int rc;
+	struct xgq_cmd_config_cu *c = (struct xgq_cmd_config_cu *)cmd;
+
+	if(c->cu_domain==(SCU_DOMAIN>>16)) {
+		rc = zert_create_scu(zert, c);
+		init_resp(resp, cmd->cid, rc);
+	} else {
+		rc = zert_create_cu(zert, c);
+		init_resp(resp, cmd->cid, rc);
+	}
+}
+
+static void zert_cmd_query_cu(struct zocl_ctrl_ert *zert, struct xgq_cmd_sq_hdr *cmd,
+			      struct xgq_com_queue_entry *resp)
+{
+	struct zocl_ctrl_ert_cu *cu;
+	struct xgq_cmd_query_cu *c = (struct xgq_cmd_query_cu *)cmd;
+	struct xgq_cmd_resp_query_cu *r = (struct xgq_cmd_resp_query_cu *)resp;
+
+	if(c->cu_domain == (SCU_DOMAIN>>16)) {
+		if (zert->zce_num_scus <= c->cu_idx) {
+			zert_err(zert, "SCU index (%d) out of range", c->cu_idx);
+			init_resp(resp, cmd->cid, -EINVAL);
+			return;
+		}
+
+		cu = &zert->zce_scus[c->cu_idx];
+		if (!cu->zcec_pdev) {
+			zert_err(zert, "SCU index (%d) not exists", c->cu_idx);
+			init_resp(resp, cmd->cid, -ENOENT);
+			return;
+		}
+	} else {
+		if (zert->zce_num_cus <= c->cu_idx) {
+			zert_err(zert, "CU index (%d) out of range", c->cu_idx);
+			init_resp(resp, cmd->cid, -EINVAL);
+			return;
+		}
+
+		cu = &zert->zce_cus[c->cu_idx];
+		if (!cu->zcec_pdev) {
+			zert_err(zert, "CU index (%d) not exists", c->cu_idx);
+			init_resp(resp, cmd->cid, -ENOENT);
+			return;
+		}
+	}
+
+	init_resp(resp, cmd->cid, 0);
+
+	switch (c->type) {
+	case XGQ_CMD_QUERY_CU_CONFIG:
+		r->xgq_id = cu->zcec_xgq_idx;
+		r->type = XGQ_CMD_RESP_QUERY_XGQ;
+		r->offset = zert->zce_cu_xgqs[r->xgq_id].zcecx_ring - zert->zce_cq_start;
+		break;
+	case XGQ_CMD_QUERY_CU_STATUS:
+		if(c->cu_domain == (SCU_DOMAIN>>16)) {
+			r->status = zocl_scu_get_status(cu->zcec_pdev);
+		} else {
+			r->status = zocl_cu_get_status(cu->zcec_pdev);
+		}
+		break;
+	default:
+		zert_err(zert, "Unknown query cu type: %d", c->type);
+		init_resp(resp, cmd->cid, -EINVAL);
+		break;
+	}
+}
+
+struct zert_ops {
+	u32 op;
+	char *name;
+	cmd_handler handler;
+} zert_op_table[] = {
+	{ XGQ_CMD_OP_CFG_START, "XGQ_CMD_OP_CFG_START", zert_cmd_cfg_start },
+	{ XGQ_CMD_OP_CFG_END, "XGQ_CMD_OP_CFG_END", zert_cmd_cfg_end },
+	{ XGQ_CMD_OP_CFG_CU, "XGQ_CMD_OP_CFG_CU", zert_cmd_cfg_cu },
+	{ XGQ_CMD_OP_QUERY_CU, "XGQ_CMD_OP_QUERY_CU", zert_cmd_query_cu },
+	{ XGQ_CMD_OP_IDENTIFY, "XGQ_CMD_OP_IDENTIFY", zert_cmd_identify }
+};
+
+static inline const struct zert_ops *opcode2op(u32 op)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(zert_op_table); i++) {
+		if (zert_op_table[i].op == op)
+			return &zert_op_table[i];
+	}
+	return NULL;
+}
+
+static inline const char *opcode2name(u32 opcode)
+{
+	const struct zert_ops *op = opcode2op(opcode);
+
+	return op ? op->name : "UNKNOWN_CMD";
+}
+
+static inline cmd_handler opcode2handler(u32 opcode)
+{
+	const struct zert_ops *op = opcode2op(opcode);
+
+	return op ? op->handler : NULL;
+}
+
+/* All control command is run-to-complete, no async process is supported. */
+static void zert_cmd_handler(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd)
+{
+	struct zocl_ctrl_ert *zert = platform_get_drvdata(pdev);
+	u32 op = cmd->opcode;
+	cmd_handler func = opcode2handler(op);
+	struct xgq_com_queue_entry r = {};
+
+	zert_info(zert, "%s received", opcode2name(op));
+	if (func)
+		func(zert, cmd, &r);
+	else
+		zert_cmd_default_handler(zert, cmd, &r);
+	zxgq_send_response(zert->zce_ctrl_xgq_hdl, &r);
+	kfree(cmd);
+}
+
+struct platform_device *zert_get_scu_pdev(struct platform_device *pdev, u32 cu_idx)
+{
+	struct zocl_ctrl_ert *zert = platform_get_drvdata(pdev);
+	struct zocl_ctrl_ert_cu *cu = NULL;
+
+	if((zert->zce_num_scus <= 0) && (cu_idx >= zert->zce_num_scus))
+		return NULL;
+
+	cu = &zert->zce_scus[cu_idx];
+	return(cu->zcec_pdev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_cu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_cu.c
@@ -0,0 +1,546 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * MPSoC based OpenCL accelerators Compute Units.
+ *
+ * Copyright (C) 2019-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Min Ma      <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+
+#include <drm/drm.h>
+#include <drm/drm_print.h>
+#include <linux/io.h>
+
+#include "zocl_cu.h"
+
+void
+zocl_cu_disable_intr(struct zocl_cu *cu, u32 type)
+{
+	cu->funcs->disable_intr(cu->core, type);
+}
+
+void
+zocl_cu_enable_intr(struct zocl_cu *cu, u32 type)
+{
+	cu->funcs->enable_intr(cu->core, type);
+}
+
+u32
+zocl_cu_clear_intr(struct zocl_cu *cu)
+{
+	return cu->funcs->clear_intr(cu->core);
+}
+
+int
+zocl_cu_get_credit(struct zocl_cu *cu)
+{
+	struct zcu_core *cu_core = cu->core;
+
+	cu_core->credits--;
+	return cu_core->credits;
+}
+
+void
+zocl_cu_refund_credit(struct zocl_cu *cu, u32 count)
+{
+	struct zcu_core *cu_core = cu->core;
+
+	cu_core->credits += count;
+}
+
+void
+zocl_cu_configure(struct zocl_cu *cu, u32 *data, size_t sz, int type)
+{
+	cu->funcs->configure(cu->core, data, sz, type);
+}
+
+void
+zocl_cu_start(struct zocl_cu *cu)
+{
+	cu->funcs->start(cu->core);
+}
+
+void
+zocl_cu_check(struct zocl_cu *cu)
+{
+	struct zcu_tasks_info tasks;
+
+	cu->funcs->check(cu->core, &tasks);
+	cu->done_cnt += tasks.num_tasks_done;
+	cu->ready_cnt += tasks.num_tasks_ready;
+}
+
+void
+zocl_cu_reset(struct zocl_cu *cu)
+{
+	cu->funcs->reset(cu->core);
+}
+
+int
+zocl_cu_reset_done(struct zocl_cu *cu)
+{
+	return cu->funcs->reset_done(cu->core);
+}
+
+phys_addr_t
+zocl_cu_get_paddr(struct zocl_cu *cu)
+{
+	struct zcu_core *cu_core = cu->core;
+
+	return cu_core->paddr;
+}
+
+void
+zocl_cu_status_print(struct zocl_cu *cu)
+{
+	struct zcu_core *cu_core = cu->core;
+
+	if (!cu_core)
+		return;
+
+	DRM_INFO("addr 0x%llx, status 0x%x",
+	    (u64)cu_core->paddr, ioread32(cu_core->vaddr));
+}
+
+int
+zocl_cu_status_get(struct zocl_cu *cu)
+{
+	struct zcu_core *cu_core = cu->core;
+
+	if (!cu_core)
+		return -1;//soft cu has crashed
+
+	return (u32)ioread32(cu_core->vaddr);
+}
+
+u32
+zocl_cu_get_control(struct zocl_cu *cu)
+{
+	struct zcu_core *cu_core = cu->core;
+
+	return cu_core->control;
+}
+
+/* -- HLS adapter start -- */
+/* HLS adapter implementation realted code. */
+static void
+zocl_hls_enable_intr(void *core, u32 intr_type)
+{
+	struct zcu_core *cu_core = core;
+	u32 intr_mask = intr_type & CU_INTR_DONE;
+
+	/* 0x04 and 0x08 -- Interrupt Enable Registers */
+	iowrite32(0x1, cu_core->vaddr + 1);
+	/*
+	 * bit 0 is ap_done, bit 1 is ap_ready
+	 * only enable ap_done before dataflow support, interrupts are handled
+	 * in sched_exec_isr, please see dataflow comments for more information.
+	 */
+	iowrite32(intr_mask, cu_core->vaddr + 2);
+}
+
+static void
+zocl_hls_disable_intr(void *core, u32 intr_type)
+{
+	struct zcu_core *cu_core = core;
+	u32 intr_mask = intr_type & ioread32(cu_core->vaddr + 2);
+
+	/* 0x04 and 0x08 -- Interrupt Enable Registers */
+	iowrite32(0x0, cu_core->vaddr + 1);
+	/* bit 0 is ap_done, bit 1 is ap_ready, disable both of interrupts */
+	iowrite32(intr_mask, cu_core->vaddr + 2);
+}
+
+static u32
+zocl_hls_clear_intr(void *core)
+{
+	struct zcu_core *cu_core = core;
+
+	/* Clear all interrupts of the CU
+	 *
+	 * HLS style kernel has Interrupt Status Register at offset 0x0C
+	 * It has two interrupt bits, bit[0] is ap_done, bit[1] is ap_ready.
+	 *
+	 * The ap_done interrupt means this CU is complete.
+	 * The ap_ready interrupt means all inputs have been read.
+	 */
+	if (cu_core->max_credits == 1) {
+		u32 isr;
+
+		/*
+		 * The old HLS adapter.
+		 *
+		 * The Interrupt Status Register is Toggle On Write
+		 * RegData = RegData ^ WriteData
+		 *
+		 * So, the reliable way to clear this register is read
+		 * then write the same value back.
+		 *
+		 * Do not write 1 to this register.  If, somehow, the
+		 * status register is 0, write 1 to this register will
+		 * trigger interrupt.
+		 */
+		isr = ioread32(cu_core->vaddr + 3);
+		iowrite32(isr, cu_core->vaddr + 3);
+		return isr;
+	}
+
+	/*
+	 * The new HLS adapter with queue.
+	 *
+	 * The Interrupt Status Register is Clear on Read.
+	 *
+	 * For debug purpose, This register is toggle on write.
+	 * Write 1 to this register will trigger interrupt.
+	 */
+	return ioread32(cu_core->vaddr + 3);
+}
+
+static void
+zocl_hls_configure(void *core, u32 *data, size_t sz, int type)
+{
+	struct zcu_core *cu_core = core;
+	u32 *base_addr = cu_core->vaddr;
+	u32 i, offset, val;
+
+	switch (type) {
+	case CONSECUTIVE:
+		/* Write register map, starting at base_addr + 0x10 (byte)
+		 * This based on the fact that kernel used
+		 *	0x00 -- Control Register
+		 *	0x04 and 0x08 -- Interrupt Enable Registers
+		 *	0x0C -- Interrupt Status Register
+		 * Skip the first 4 words in user regmap.
+		 */
+		for (i = 4; i < sz; ++i)
+			iowrite32(data[i], base_addr + i);
+		break;
+	case PAIRS:
+		/* This is the {offset, value} pairs to configure CU.
+		 * It relies on the KDS/ERT command format.
+		 * The data in the command is 32 bits.
+		 */
+		for (i = 0; i < sz - 1; i += 2) {
+			 /* The offset is the offset to CU base address */
+			offset = *(data + i);
+			val = *(data + i + 1);
+
+			iowrite32(val, base_addr + offset / 4);
+		}
+		break;
+	}
+}
+
+static void
+zocl_hls_start(void *core)
+{
+	struct zcu_core *cu_core = core;
+
+	/* Bit 0 -- The CU start control bit.
+	 * Write 0 to this bit will be ignored.
+	 * Until the CU is ready to take next task, this bit will reamin 1.
+	 * Once ths CU is ready, it will clear this bit.
+	 * So, if this bit is 1, it means the CU is running.
+	 */
+	iowrite32(0x1, cu_core->vaddr);
+}
+
+static void
+zocl_hls_check(void *core, struct zcu_tasks_info *tasks_info)
+{
+	struct zcu_core *cu_core = core;
+	u32 version;
+	u32 ctrl_reg;
+	u32 ready_cnt = 0;
+	u32 done_cnt = 0;
+
+	/* done is indicated by AP_DONE(2) alone or by AP_DONE(2) | AP_IDLE(4)
+	 * but not by AP_IDLE itself.  Since 0x10 | (0x10 | 0x100) = 0x110
+	 * checking for 0x10 is sufficient.
+	 */
+	ctrl_reg  = ioread32(cu_core->vaddr);
+	version   = (ctrl_reg & CU_VERSION_MASK) >> 8;
+
+	/* For the old version of HLS adapter
+	 * There is no ready and done counter. If done bit is 1, means CU is
+	 * ready for a new command and a command was done.
+	 */
+	if (version != 0) {
+		ready_cnt = (ctrl_reg & CU_READY_CNT_MASK) >> 16;
+		done_cnt  = (ctrl_reg & CU_DONE_CNT_MASK) >> 24;
+	} else if (ctrl_reg & CU_AP_DONE) {
+		ready_cnt = 1;
+		done_cnt = 1;
+
+		/*
+		 * wrtie AP_CONTINUE to restart CU.
+		 * this is safe for all hls/versal kernel
+		 */
+		iowrite32(CU_AP_CONTINUE, cu_core->vaddr);
+		/*
+		 * reading AP_DONE is redudent, it should be done in next cycle.
+		 */
+		ctrl_reg = ioread32(cu_core->vaddr);
+		if ((ctrl_reg & CU_AP_DONE) != 0)
+			DRM_ERROR("AP_DONE is not zero: 0x%x", ctrl_reg);
+
+	}
+
+	tasks_info->num_tasks_ready = ready_cnt;
+	tasks_info->num_tasks_done = done_cnt;
+}
+
+static void
+zocl_hls_reset(void *core)
+{
+	struct zcu_core *cu_core = core;
+
+	iowrite32(CU_AP_RESET, cu_core->vaddr);
+}
+
+static int
+zocl_hls_reset_done(void *core)
+{
+	struct zcu_core *cu_core = core;
+	u32 status;
+
+	status = ioread32(cu_core->vaddr);
+
+	/* reset done is indicated by AP_RESET_DONE, bit 6 */
+	if (status & (1 << 6))
+		return true;
+
+	return false;
+}
+
+static struct zcu_funcs hls_adapter_ops = {
+	.enable_intr	= zocl_hls_enable_intr,
+	.disable_intr	= zocl_hls_disable_intr,
+	.clear_intr	= zocl_hls_clear_intr,
+	.configure	= zocl_hls_configure,
+	.start		= zocl_hls_start,
+	.check		= zocl_hls_check,
+	.reset		= zocl_hls_reset,
+	.reset_done	= zocl_hls_reset_done,
+};
+
+static int
+zocl_hls_cu_init(struct zocl_cu *cu, phys_addr_t paddr)
+{
+	struct zcu_core *core;
+	u32 ctrl_reg;
+	u32 version;
+	u32 max_cap;
+
+	core = vzalloc(sizeof(struct zcu_core));
+	if (!core) {
+		DRM_ERROR("Could not allocate CU core object\n");
+		return -ENOMEM;
+	}
+
+	core->control = paddr & 0x7;
+	paddr = paddr & ZOCL_KDS_MASK;
+	core->paddr = paddr;
+	core->vaddr = ioremap(paddr, CU_SIZE);
+	if (!core->vaddr) {
+		DRM_ERROR("Mapping CU failed\n");
+		vfree(core);
+		return -ENOMEM;
+	}
+
+	DRM_DEBUG("CU 0x%llx map to 0x%p\n", (u64)core->paddr, core->vaddr);
+	ctrl_reg = ioread32(core->vaddr);
+	version = (ctrl_reg & CU_VERSION_MASK) >> 8;
+	max_cap = (ctrl_reg & CU_MAX_CAP_MASK) >> 12;
+	switch (version) {
+	case 1:
+		core->max_credits = 1 << max_cap;
+		break;
+	default:
+		core->max_credits = 1;
+	}
+	core->credits = core->max_credits;
+
+	core->intr_type = CU_INTR_DONE | CU_INTR_READY;
+
+	/* In case CU object is not initialled as 0 */
+	cu->done_cnt = 0;
+	cu->ready_cnt = 0;
+	cu->usage = 0;
+	cu->core = core;
+	cu->funcs = &hls_adapter_ops;
+
+	INIT_LIST_HEAD(&cu->running_queue);
+
+	return 0;
+}
+
+static int
+zocl_hls_cu_fini(struct zocl_cu *cu)
+{
+	struct zcu_core *core = cu->core;
+
+	if (!core)
+		return 0;
+
+	if (core->vaddr)
+		iounmap(core->vaddr);
+	vfree(core);
+
+	return 0;
+}
+
+/* -- HLS adapter end -- */
+
+/* -- ACC adapter start -- */
+static void
+zocl_acc_configure(void *core, u32 *data, size_t sz, int type)
+{
+	struct zcu_core *cu_core = core;
+	u32 *base_addr = cu_core->vaddr;
+	u32 i, offset, val;
+
+	if (type != PAIRS)
+		return;
+
+	/*
+	 * Same open issue like HLS adapter
+	 * Skip 6 data,this is how user layer construct the command.
+	 */
+	for (i = 6; i < sz - 1; i += 2) {
+		offset = *(data + i) - cu_core->paddr;
+		val = *(data + i + 1);
+
+		iowrite32(val, base_addr + offset/4);
+	}
+}
+
+static void
+zocl_acc_start(void *core)
+{
+	struct zcu_core *cu_core = core;
+	/* 0x08 -- Command register
+	 * Write a zero to the command queue to indicate the start of a command
+	 */
+	iowrite32(0x0, cu_core->vaddr + 2);
+}
+
+static void
+zocl_acc_check(void *core, struct zcu_tasks_info *tasks_info)
+{
+	struct zcu_core *cu_core = core;
+	u32 status;
+
+	tasks_info->num_tasks_ready = 0;
+	tasks_info->num_tasks_done = 0;
+	/* 0x04 -- Status register. If the CU is idle, the value is 0x6 or 0x4.
+	 * Bit 5, O means a task is finished. 1 means done queue empty
+	 * So, if the CU is running or idle, this bit would be 1.
+	 */
+	status = ioread32(cu_core->vaddr + 1);
+	if ((status & 0x20) == 0) {
+		/* One command is done.
+		 * This adapter didn't support CU ready signal.
+		 * So think the CU alway ready and done at the same time.
+		 */
+		tasks_info->num_tasks_ready = 1;
+		tasks_info->num_tasks_done = 1;
+	}
+}
+
+static struct zcu_funcs acc_adapter_ops = {
+	.configure	= zocl_acc_configure,
+	.start		= zocl_acc_start,
+	.check		= zocl_acc_check,
+};
+
+static int
+zocl_acc_cu_init(struct zocl_cu *cu, phys_addr_t paddr)
+{
+	struct zcu_core *core;
+
+	core = vzalloc(sizeof(struct zcu_core));
+	if (!core) {
+		DRM_ERROR("Could not allocate CU core object\n");
+		return -ENOMEM;
+	}
+
+	core->paddr = paddr;
+	core->vaddr = ioremap(paddr, CU_SIZE);
+	if (!core->vaddr) {
+		DRM_ERROR("Mapping CU failed\n");
+		vfree(core);
+		return -ENOMEM;
+	}
+
+	DRM_DEBUG("CU 0x%llx map to 0x%p\n", (u64)core->paddr, core->vaddr);
+	/* Unless otherwise configured, the adapter IP has space for 16
+	 * outstanding computations.
+	 */
+	core->max_credits = 16;
+	core->credits = core->max_credits;
+
+	core->intr_type = 0;
+	core->control = 0;
+
+	cu->done_cnt = 0;
+	cu->ready_cnt = 0;
+	cu->usage = 0;
+	cu->core = core;
+	cu->funcs = &acc_adapter_ops;
+
+	INIT_LIST_HEAD(&cu->running_queue);
+
+	return 0;
+}
+
+static int
+zocl_acc_cu_fini(struct zocl_cu *cu)
+{
+	struct zcu_core *core = cu->core;
+
+	if (!core)
+		return 0;
+
+	if (core->vaddr)
+		iounmap(core->vaddr);
+	vfree(core);
+
+	return 0;
+}
+/* -- ACC adapter end -- */
+
+int zocl_cu_init(struct zocl_cu *cu, enum zcu_model m, phys_addr_t paddr)
+{
+	cu->model = m;
+	switch (cu->model) {
+	case MODEL_HLS:
+		return zocl_hls_cu_init(cu, paddr);
+	case MODEL_ACC:
+		return zocl_acc_cu_init(cu, paddr);
+	default:
+		DRM_ERROR("Unknown CU model\n");
+		return -EINVAL;
+	}
+}
+
+int zocl_cu_fini(struct zocl_cu *cu)
+{
+	if (!cu)
+		return 0;
+
+	switch (cu->model) {
+	case MODEL_HLS:
+		return zocl_hls_cu_fini(cu);
+	case MODEL_ACC:
+		return zocl_acc_cu_fini(cu);
+	default:
+		DRM_ERROR("Unknown CU model\n");
+		return -EINVAL;
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_cu_xgq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_cu_xgq.c
@@ -0,0 +1,523 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include "zocl_lib.h"
+#include "zocl_drv.h"
+#include "zocl_xgq.h"
+#include "zocl_cu_xgq.h"
+/* CU XGQ driver name. */
+#define ZCU_XGQ_NAME "zocl_cu_xgq"
+
+#define ZCU_XGQ2PDEV(zcu_xgq)			((zcu_xgq)->zxc_pdev)
+#define ZCU_XGQ2DEV(zcu_xgq)			(&ZCU_XGQ2PDEV(zcu_xgq)->dev)
+#define zcu_xgq_err(zcu_xgq, fmt, args...)	zocl_err(ZCU_XGQ2DEV(zcu_xgq), fmt"\n", ##args)
+#define zcu_xgq_info(zcu_xgq, fmt, args...)	zocl_info(ZCU_XGQ2DEV(zcu_xgq), fmt"\n", ##args)
+#define zcu_xgq_dbg(zcu_xgq, fmt, args...)	zocl_dbg(ZCU_XGQ2DEV(zcu_xgq), fmt"\n", ##args)
+
+#define ZCU_XGQ_MAX_SLOT_SIZE	1024
+#define ZCU_XGQ_FAST_PATH(zcu_xgq)		((zcu_xgq)->zxc_num_cu == 1)
+
+static void zcu_xgq_cmd_handler(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd);
+
+#ifdef ZCU_XGQ_DEBUG
+#include <linux/circ_buf.h>
+
+struct log_ring {
+	char			*lr_buf;
+	size_t			lr_size;
+	size_t			lr_head;
+	size_t			lr_tail;
+};
+
+int lr_init(struct log_ring *lr, size_t size)
+{
+	lr->lr_buf = vzalloc(size);
+	if (!lr->lr_buf)
+		return -ENOMEM;
+
+	lr->lr_size = size;
+	lr->lr_head = 0;
+	lr->lr_tail = 0;
+	return 0;
+}
+
+void lr_fini(struct log_ring *lr)
+{
+	vfree(lr->lr_buf);
+}
+
+void lr_produce(struct log_ring *lr, char *log, size_t size)
+{
+	size_t head = lr->lr_head;
+	size_t tail = lr->lr_tail;
+	size_t space = CIRC_SPACE(head, tail, lr->lr_size);
+	/* return min(head pointer to the end of buffer, CIRC_SPACE()) */
+	size_t space_to_end = CIRC_SPACE_TO_END(head, tail, lr->lr_size);
+
+	if (!lr || !lr->lr_buf || !log)
+		return;
+
+	if (size > space) {
+		tail = (tail + size - space) & (lr->lr_size - 1);
+		space = CIRC_SPACE(head, tail, lr->lr_size);
+		space_to_end = CIRC_SPACE_TO_END(head, tail, lr->lr_size);
+		lr->lr_tail = tail;
+	}
+	/* Copy data to buffer. Depende on if it cross the end of the ring
+	 * buffer, there are two situations.
+	 */
+	if (space_to_end != space) {
+		memcpy(lr->lr_buf + head, log, space_to_end);
+		memcpy(lr->lr_buf, log + space_to_end, size - space_to_end);
+	} else
+		memcpy(lr->lr_buf + head, log, size);
+
+	 /* Update head/tail pointer. We might overwrite oldest data, this is
+	  * why tail pointer needs updat as well
+	  */
+	lr->lr_head = (lr->lr_head + size) & (lr->lr_size - 1);
+}
+
+ssize_t lr_consume(struct log_ring *lr, char *buf, size_t size)
+{
+	size_t head = lr->lr_head;
+	size_t tail = lr->lr_tail;
+	size_t cnt = CIRC_CNT(head, tail, lr->lr_size);
+	/* return min(count to the end of buffer, CIRC_CNT()) */
+	size_t cnt_to_end = CIRC_CNT_TO_END(head, tail, lr->lr_size);
+	size_t nread = 0;
+
+	if (!lr || !lr->lr_buf || !buf)
+		return 0;
+
+	if (size < cnt)
+		nread = size;
+	else
+		nread = cnt;
+
+	if (nread <= cnt_to_end) {
+		memcpy(buf, lr->lr_buf + tail, nread);
+		lr->lr_tail += nread;
+	} else {
+		/* Cross the end of the buffer, two times of copy */
+		memcpy(buf, lr->lr_buf + tail, cnt_to_end);
+		memcpy(buf + cnt_to_end, lr->lr_buf, nread - cnt_to_end);
+		lr->lr_tail = nread - cnt_to_end;
+	}
+
+	return nread;
+}
+#endif
+
+struct zocl_cu_xgq {
+	struct platform_device	*zxc_pdev;
+	struct zocl_cu_xgq_info	*zxc_pdata;
+
+	void			*zxc_zxgq_hdl;
+	void			*zxc_client_hdl;
+	struct drm_zocl_dev	*zxc_zdev;
+
+	struct mutex		zxc_lock;
+	u32			zxc_cu_domain;
+	u32			zxc_cu_idx;
+	size_t			zxc_num_cu;
+
+	u32			zxc_irq;
+	void __iomem		*zxc_ring;
+	size_t			zxc_ring_size;
+	void __iomem		*zxc_xgq_ip;
+	void __iomem		*zxc_cq_prod_int;
+#ifdef ZCU_XGQ_DEBUG
+	struct log_ring		zxc_log;
+#endif
+};
+
+static ssize_t
+debug_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct zocl_cu_xgq *zcu_xgq = (struct zocl_cu_xgq *)dev_get_drvdata(dev);
+	struct kds_client *client;
+	ssize_t sz;
+
+	sz = sprintf(buf, "zcu_xgq %p\n", zcu_xgq);
+
+	client = zcu_xgq->zxc_client_hdl;
+	sz += sprintf(buf+sz, "s_cnt %ld\n", client_stat_read(client, s_cnt[0]));
+	sz += sprintf(buf+sz, "c_cnt %ld\n", client_stat_read(client, c_cnt[0]));
+
+	return sz;
+}
+static DEVICE_ATTR_RO(debug);
+
+static struct attribute *zcu_xgq_attrs[] = {
+	&dev_attr_debug.attr,
+	NULL,
+};
+
+static ssize_t
+xgq_ring(struct file *filp, struct kobject *kobj,
+	 struct bin_attribute *attr, char *buf,
+	 loff_t offset, size_t count)
+{
+	struct zocl_cu_xgq *zcu_xgq;
+	struct device *dev = container_of(kobj, struct device, kobj);
+	ssize_t nread = 0;
+	size_t size = 0;
+
+	zcu_xgq = (struct zocl_cu_xgq *)dev_get_drvdata(dev);
+	if (!zcu_xgq || !zcu_xgq->zxc_ring)
+		return 0;
+
+	size = zcu_xgq->zxc_ring_size;
+	if (offset >= size)
+		goto done;
+
+	if (offset + count < size)
+		nread = count;
+	else
+		nread = size - offset;
+
+	memcpy_fromio(buf, zcu_xgq->zxc_ring + offset, nread);
+
+done:
+	return nread;
+}
+
+static struct bin_attribute ring_attr = {
+	.attr = {
+		.name ="xgq_ring",
+		.mode = 0444
+	},
+	.read = xgq_ring,
+	.write = NULL,
+	.size = 0
+};
+
+#ifdef ZCU_XGQ_DEBUG
+static ssize_t
+cmd_log_show(struct file *filp, struct kobject *kobj,
+	struct bin_attribute *attr, char *buf,
+	loff_t offset, size_t count)
+{
+	struct zocl_cu_xgq *zcu_xgq;
+	struct device *dev = container_of(kobj, struct device, kobj);
+
+	zcu_xgq = (struct zocl_cu_xgq *)dev_get_drvdata(dev);
+	if (!zcu_xgq)
+		return 0;
+
+	return lr_consume(&zcu_xgq->zxc_log, buf, count);
+}
+
+static struct bin_attribute log_attr = {
+	.attr = {
+		.name ="cmd_log",
+		.mode = 0444
+	},
+	.read = cmd_log_show,
+	.write = NULL,
+	.size = 0
+};
+#endif
+
+static struct bin_attribute *zcu_xgq_bin_attrs[] = {
+	&ring_attr,
+#ifdef ZCU_XGQ_DEBUG
+	&log_attr,
+#endif
+	NULL,
+};
+
+static const struct attribute_group zcu_xgq_attrgroup = {
+	.attrs = zcu_xgq_attrs,
+	.bin_attrs = zcu_xgq_bin_attrs,
+};
+
+static inline void reg_write(void __iomem  *addr, u32 val)
+{
+	iowrite32(val, addr);
+}
+
+static inline u32 reg_read(void __iomem *addr)
+{
+	return ioread32(addr);
+}
+
+static void zcu_xgq_init_xgq(struct zocl_cu_xgq *zcu_xgq)
+{
+	struct zocl_xgq_init_args arg = {};
+
+	arg.zxia_pdev = zcu_xgq->zxc_pdev;
+	arg.zxia_irq = zcu_xgq->zxc_irq;
+	arg.zxia_ring = zcu_xgq->zxc_ring;
+	arg.zxia_ring_size = zcu_xgq->zxc_ring_size;
+	arg.zxia_ring_slot_size = zcu_xgq->zxc_pdata->zcxi_slot_size;
+	arg.zxia_intc_pdev = zcu_xgq->zxc_pdata->zcxi_intc_pdev;
+	if (ZCU_XGQ_MAX_SLOT_SIZE < arg.zxia_ring_slot_size)
+		arg.zxia_ring_slot_size = ZCU_XGQ_MAX_SLOT_SIZE;
+	arg.zxia_xgq_ip = zcu_xgq->zxc_xgq_ip;
+	arg.zxia_cq_prod_int = zcu_xgq->zxc_cq_prod_int;
+	arg.zxia_cmd_handler = zcu_xgq->zxc_pdata->zcxi_echo_mode ? NULL : zcu_xgq_cmd_handler;
+	arg.zxia_simple_cmd_hdr = ZCU_XGQ_FAST_PATH(zcu_xgq);
+
+	/* Init CU XGQ */
+	zcu_xgq->zxc_zxgq_hdl = zxgq_init(&arg);
+	if (!zcu_xgq->zxc_zxgq_hdl)
+		zcu_xgq_err(zcu_xgq, "failed to initialize CU XGQ");
+}
+
+static void zcu_xgq_fini_xgq(struct zocl_cu_xgq *zcu_xgq)
+{
+	if (zcu_xgq->zxc_zxgq_hdl)
+		zxgq_fini(zcu_xgq->zxc_zxgq_hdl);
+	zcu_xgq->zxc_zxgq_hdl = NULL;
+}
+
+static int zcu_xgq_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct zocl_cu_xgq *zcu_xgq = devm_kzalloc(&pdev->dev, sizeof(*zcu_xgq), GFP_KERNEL);
+	int ret;
+
+	if (!zcu_xgq)
+		return -ENOMEM;
+	zcu_xgq->zxc_pdev = pdev;
+
+	res = platform_get_resource_byname(ZCU_XGQ2PDEV(zcu_xgq), IORESOURCE_IRQ, ZCX_RES_IRQ);
+	if (!res) {
+		zcu_xgq_err(zcu_xgq, "failed to find CU XGQ IRQ"); 
+		return -EINVAL;
+	}
+	zcu_xgq->zxc_irq = res->start;
+	zcu_xgq_info(zcu_xgq, "CU XGQ IRQ: %d", zcu_xgq->zxc_irq); 
+
+	zcu_xgq->zxc_pdata = dev_get_platdata(ZCU_XGQ2DEV(zcu_xgq));
+	BUG_ON(zcu_xgq->zxc_pdata == NULL);
+
+	zcu_xgq->zxc_ring = zlib_map_res_by_name(pdev, ZCX_RES_RING, NULL, &zcu_xgq->zxc_ring_size);
+	if (!zcu_xgq->zxc_ring)
+		return -EINVAL;
+
+	ret = zocl_create_client(ZCU_XGQ2DEV(zcu_xgq), &zcu_xgq->zxc_client_hdl);
+	if (ret)
+		return ret;
+
+	zcu_xgq->zxc_xgq_ip = zlib_map_res_by_name(pdev, ZCX_RES_XGQ_IP, NULL, NULL);
+	zcu_xgq->zxc_cq_prod_int = zlib_map_res_by_name(pdev, ZCX_RES_CQ_PROD_INT, NULL, NULL);
+
+	zcu_xgq->zxc_zdev = zocl_get_zdev();
+	mutex_init(&zcu_xgq->zxc_lock);
+	platform_set_drvdata(pdev, zcu_xgq);
+
+#ifdef ZCU_XGQ_DEBUG
+	ret = lr_init(&zcu_xgq->zxc_log, 4 * 1024 * 1024);
+	if (ret)
+		zcu_xgq_info(zcu_xgq, "create ZCU_XGQ log buffer failed");
+#endif
+
+	ret = sysfs_create_group(&pdev->dev.kobj, &zcu_xgq_attrgroup);
+	if (ret)
+		zcu_xgq_err(zcu_xgq, "create ZCU_XGQ attrs failed: %d", ret);
+	return 0;
+}
+
+static int zcu_xgq_remove(struct platform_device *pdev)
+{
+	struct zocl_cu_xgq *zcu_xgq = platform_get_drvdata(pdev);
+
+	zcu_xgq_info(zcu_xgq, "Removing %s", ZCU_XGQ_NAME);
+
+	sysfs_remove_group(&pdev->dev.kobj, &zcu_xgq_attrgroup);
+
+#ifdef ZCU_XGQ_DEBUG
+	lr_fini(&zcu_xgq->zxc_log);
+#endif
+
+	mutex_destroy(&zcu_xgq->zxc_lock);
+	if (zcu_xgq->zxc_client_hdl)
+		zocl_destroy_client(zcu_xgq->zxc_client_hdl);
+	zcu_xgq_fini_xgq(zcu_xgq);
+	return 0;
+}
+
+static const struct platform_device_id zocl_cu_xgq_id_match[] = {
+	{ CU_XGQ_DEV_NAME, 0 },
+	{ /* end of table */ },
+};
+
+struct platform_driver zocl_cu_xgq_driver = {
+	.driver = {
+		.name = ZCU_XGQ_NAME,
+	},
+	.probe  = zcu_xgq_probe,
+	.remove = zcu_xgq_remove,
+	.id_table = zocl_cu_xgq_id_match,
+};
+
+int zcu_xgq_assign_cu(struct platform_device *pdev, u32 cu_idx, u32 cu_domain)
+{
+	int rc = 0;
+	struct zocl_cu_xgq *zcu_xgq = platform_get_drvdata(pdev);
+
+	mutex_lock(&zcu_xgq->zxc_lock);
+	zcu_xgq->zxc_num_cu++;
+	/* For optimization when there is only 1 CU. */
+	zcu_xgq->zxc_cu_domain = cu_domain;
+	zcu_xgq->zxc_cu_idx = cu_idx;
+	rc = zocl_add_context_kernel(zcu_xgq->zxc_zdev, zcu_xgq->zxc_client_hdl,
+				     cu_idx, CU_CTX_SHARED, cu_domain);
+	if (!rc) {
+		/* Re-init xgq since we may have > 1 CU assigned so can't use fast path anymore. */
+		zcu_xgq_fini_xgq(zcu_xgq);
+		zcu_xgq_init_xgq(zcu_xgq);
+	}
+	mutex_unlock(&zcu_xgq->zxc_lock);
+
+	zcu_xgq_info(zcu_xgq, "CU Domain[%d] CU[%d] assigned", cu_domain, cu_idx);
+	return rc;
+}
+
+int zcu_xgq_unassign_cu(struct platform_device *pdev, u32 cu_idx, u32 cu_domain)
+{
+	int rc = 0;
+	struct zocl_cu_xgq *zcu_xgq;
+
+	BUG_ON(pdev == NULL);
+	zcu_xgq = platform_get_drvdata(pdev);
+
+	BUG_ON(zcu_xgq == NULL);
+	mutex_lock(&zcu_xgq->zxc_lock);
+	zcu_xgq->zxc_num_cu--;
+	rc = zocl_del_context_kernel(zcu_xgq->zxc_zdev, zcu_xgq->zxc_client_hdl, cu_idx, cu_domain);
+	mutex_unlock(&zcu_xgq->zxc_lock);
+	return rc;
+}
+
+static void init_resp(struct xgq_com_queue_entry *resp, u16 cid, u32 rcode)
+{
+	memset(resp, 0, sizeof(*resp));
+	resp->hdr.cid = cid;
+	resp->hdr.cstate = XGQ_CMD_STATE_COMPLETED;
+	resp->rcode = rcode;
+}
+
+static inline void
+zcu_xgq_cmd_complete(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd, int ret)
+{
+	struct xgq_com_queue_entry r;
+	struct zocl_cu_xgq *zcu_xgq = platform_get_drvdata(pdev);
+
+	if (likely(ret == 0 && ZCU_XGQ_FAST_PATH(zcu_xgq))) {
+		zxgq_send_response(zcu_xgq->zxc_zxgq_hdl, NULL);
+	} else {
+		init_resp(&r, cmd->cid, ret);
+		zxgq_send_response(zcu_xgq->zxc_zxgq_hdl, &r);
+	}
+	kfree(cmd);
+}
+
+static void zcu_xgq_cmd_notify(struct kds_command *xcmd, int status)
+{
+	struct zocl_cu_xgq *zcu_xgq = (struct zocl_cu_xgq *)xcmd->priv;
+	struct xgq_cmd_sq_hdr *cmd = xcmd->info;
+
+	xcmd->info = NULL;
+	zcu_xgq_cmd_complete(ZCU_XGQ2PDEV(zcu_xgq), cmd, xcmd->rcode);
+
+	if (xcmd->cu_idx >= 0) {
+		if (cmd->cu_domain != 0)
+			client_stat_inc(xcmd->client, scu_c_cnt[xcmd->cu_idx]);
+		else
+			client_stat_inc(xcmd->client, c_cnt[xcmd->cu_idx]);
+	}
+}
+
+static inline void
+zcu_xgq_cmd_start_cuidx(struct zocl_cu_xgq *zcu_xgq, struct xgq_cmd_sq_hdr *cmd)
+{
+	struct kds_command *xcmd;
+	int mask_idx;
+	int bit_idx;
+
+#if 0
+	zcu_xgq_cmd_complete(ZCU_XGQ2PDEV(zcu_xgq), cmd, 0);
+	return;
+#endif
+	xcmd = kds_alloc_command(zcu_xgq->zxc_client_hdl, 0);
+	if (!xcmd) {
+		zcu_xgq_cmd_complete(ZCU_XGQ2PDEV(zcu_xgq), cmd, -ENOMEM);
+		return;
+	}
+
+	xcmd->info = cmd;
+	xcmd->payload_type = XGQ_CMD;
+
+	xcmd->cb.notify_host = zcu_xgq_cmd_notify;
+	xcmd->cb.free = kds_free_command;
+	xcmd->priv = zcu_xgq;
+	xcmd->response_size = 0;
+
+	if (ZCU_XGQ_FAST_PATH(zcu_xgq)) {
+		cmd->cu_domain = zcu_xgq->zxc_cu_domain;
+		mask_idx = zcu_xgq->zxc_cu_idx / 32;
+		bit_idx = zcu_xgq->zxc_cu_idx % 32;
+	} else {
+		mask_idx = cmd->cu_idx / 32;
+		bit_idx = cmd->cu_idx % 32;
+	}
+	if (cmd->cu_domain != 0) {
+		xcmd->type = KDS_SCU;
+		xcmd->opcode = OP_START_SK;
+	} else {
+		xcmd->type = KDS_CU;
+		xcmd->opcode = OP_START;
+	}
+	xcmd->cu_mask[mask_idx] = 1 << bit_idx;
+	if (mask_idx < 4) {
+		xcmd->num_mask = mask_idx + 1;
+	} else {
+		xcmd->num_mask = 0;
+	}
+
+	kds_add_command(&zcu_xgq->zxc_zdev->kds, xcmd);
+}
+
+static void zcu_xgq_cmd_default(struct zocl_cu_xgq *zcu_xgq, struct xgq_cmd_sq_hdr *cmd)
+{
+	zcu_xgq_err(zcu_xgq, "Unknown cmd: %d", cmd->opcode);
+	zcu_xgq_cmd_complete(ZCU_XGQ2PDEV(zcu_xgq), cmd, -ENOTTY);
+}
+
+static void zcu_xgq_cmd_handler(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd)
+{
+	struct zocl_cu_xgq *zcu_xgq = platform_get_drvdata(pdev);
+
+#ifdef ZCU_XGQ_DEBUG
+	lr_produce(&zcu_xgq->zxc_log, (char *)cmd, sizeof(*cmd));
+#endif
+
+	switch (cmd->opcode) {
+	case XGQ_CMD_OP_START_CUIDX:
+		zcu_xgq_dbg(zcu_xgq, "XGQ_CMD_OP_START_CUIDX received");
+		zcu_xgq_cmd_start_cuidx(zcu_xgq, cmd);
+		break;
+	case XGQ_CMD_OP_START_CUIDX_KV:
+		zcu_xgq_dbg(zcu_xgq, "XGQ_CMD_OP_START_CUIDX_KV received");
+		zcu_xgq_cmd_start_cuidx(zcu_xgq, cmd);
+		break;
+	default:
+		zcu_xgq_cmd_default(zcu_xgq, cmd);
+		break;
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_dma.c
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2019 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *    Jan Stephan  <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "zocl_dma.h"
+#include <drm/drm_print.h>
+
+static void zocl_dma_irq_done(void *data)
+{
+	zocl_dma_handle_t *dma_handle = data;
+	enum dma_status status;
+
+	status = dmaengine_tx_status(dma_handle->dma_chan,
+	    dma_handle->dma_cookie, NULL);
+
+	switch (status) {
+	case DMA_IN_PROGRESS:
+		DRM_DEBUG("%s: Received DMA_IN_PROGRESS", __func__);
+		break;
+	case DMA_PAUSED:
+		DRM_ERROR("Received DMA_PAUSED");
+		break;
+	case DMA_ERROR:
+		DRM_ERROR("Received DMA_ERROR");
+		complete(&dma_handle->dma_done);
+		/* registered callback function from user */
+		if (dma_handle->dma_func)
+			dma_handle->dma_func(dma_handle->dma_arg, -EIO);
+		break;
+	case DMA_COMPLETE:
+		complete(&dma_handle->dma_done);
+		/* registered callback function from user */
+		if (dma_handle->dma_func)
+			dma_handle->dma_func(dma_handle->dma_arg, 0);
+		break;
+	default:
+		DRM_ERROR("Received Unknown status: %d", status);
+	}
+}
+
+int zocl_dma_memcpy_pre(zocl_dma_handle_t *dma_handle,
+    dma_addr_t dst_paddr, dma_addr_t src_paddr, size_t size)
+{
+	struct dma_async_tx_descriptor 	*dma_tx;
+	int 				rc = 0;
+
+	/* prep dma memcpy engine */
+	dma_tx = dmaengine_prep_dma_memcpy(dma_handle->dma_chan, dst_paddr,
+	    src_paddr, size, DMA_CTRL_ACK);
+	if (!dma_tx) {
+		DRM_ERROR("Failed to prepare DMA memcpy\n");
+		rc = -EINVAL;
+		goto out;
+	}
+
+	dma_tx->callback = zocl_dma_irq_done;
+	dma_tx->callback_param = dma_handle;
+
+	/* submit dma engine */
+	dma_handle->dma_cookie = dmaengine_submit(dma_tx);
+	if (dma_submit_error(dma_handle->dma_cookie)) {
+		DRM_ERROR("Failed to submit dma\n");
+		rc = -EINVAL;
+		goto out;
+	}
+out:
+	return rc;
+}
+
+void zocl_dma_start(zocl_dma_handle_t *dma_handle)
+{
+	init_completion(&dma_handle->dma_done);
+	dma_async_issue_pending(dma_handle->dma_chan);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_drv.c
@@ -0,0 +1,1320 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Umang Parekh <umang.parekh@xilinx.com>
+ *    Min Ma       <min.ma@xilinx.com>
+ *    Jan Stephan  <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-buf.h>
+#include <linux/module.h>
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/iommu.h>
+#include <linux/pagemap.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/poll.h>
+#include <linux/spinlock.h>
+#include "zocl_drv.h"
+#include "zocl_sk.h"
+#include "zocl_aie.h"
+#include "zocl_bo.h"
+#include "sched_exec.h"
+#include "zocl_xclbin.h"
+#include "zocl_error.h"
+
+#define ZOCL_DRIVER_NAME        "zocl"
+#define ZOCL_DRIVER_DESC        "Zynq BO manager"
+
+static char driver_date[9];
+
+/* This should be the same as DRM_FILE_PAGE_OFFSET_START in drm_gem.c */
+#if defined(CONFIG_ARM64)
+#define ZOCL_FILE_PAGE_OFFSET   0x00100000
+#else
+#define ZOCL_FILE_PAGE_OFFSET   0x00010000
+#endif
+
+#ifndef VM_RESERVED
+#define VM_RESERVED (VM_DONTEXPAND | VM_DONTDUMP)
+#endif
+
+
+int enable_xgq_ert = 1;
+module_param(enable_xgq_ert, int, (S_IRUGO|S_IWUSR));
+MODULE_PARM_DESC(enable_xgq_ert, "0 = legacy ERT mode, 1 = XGQ ERT mode (default)");
+
+extern struct platform_driver zocl_ctrl_ert_driver;
+
+static const struct vm_operations_struct reg_physical_vm_ops = {
+#ifdef CONFIG_HAVE_IOREMAP_PROT
+	.access = generic_access_phys,
+#endif
+};
+
+
+#if KERNEL_VERSION(5, 3, 0) <= LINUX_VERSION_CODE
+static int
+match_name(struct device *dev, const void *data)
+#else
+static int
+match_name(struct device *dev, void *data)
+#endif
+{
+	const char *name = data;
+	/*
+	 * check if given name is substring inside dev.
+	 * the dev_name is like: 20300030000.ert_hw
+	 */
+	return strstr(dev_name(dev), name) != NULL;
+}
+
+/**
+ * zocl_pr_slot_init : PR Slot specific initialization
+ *
+ * @zdev: zocl device struct
+ * @pdev: platform device struct
+ *
+ * Returns 0 if initialization successfully.
+ * Returns -EINVAL if failed.
+ */
+
+static int zocl_pr_slot_init(struct drm_zocl_dev *zdev,
+		                       struct platform_device *pdev)
+{
+	struct drm_zocl_slot *zocl_slot = NULL;
+	int ret = 0;
+	int i = 0;
+
+	zdev->num_pr_slot = 0;
+	/* TODO : Need to update this function based on the device tree */
+	if (ZOCL_PLATFORM_ARM64) {
+		u64 pr_num;
+		if (!of_property_read_u64(pdev->dev.of_node,
+					  "xlnx,pr-num-support", &pr_num))
+			zdev->num_pr_slot = (int)pr_num;
+	} else {
+		/* Work around for CR-1119382 issue.
+		 * ZOCL driver is crashing if it accessing the device tree node */
+		if (false) {
+			u32 pr_num;
+			if (!of_property_read_u32(pdev->dev.of_node,
+					  "xlnx,pr-num-support", &pr_num))
+				zdev->num_pr_slot = (int)pr_num;
+		}
+	}
+
+	/* If there is no information available for number of slot available
+	 * for this device then consider it for a single slot device for
+	 * backward compartability.
+	 */
+	if (zdev->num_pr_slot == 0)
+		zdev->num_pr_slot = 1;
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = (struct drm_zocl_slot *)
+			kzalloc(sizeof(struct drm_zocl_slot), GFP_KERNEL);
+		if (!zocl_slot)
+			return -ENOMEM;
+
+		/* Initial xclbin */
+		ret = zocl_xclbin_init(zocl_slot);
+		if (ret)
+			return ret;
+
+		mutex_init(&zocl_slot->slot_xclbin_lock);
+ 
+		if (ZOCL_PLATFORM_ARM64) {
+			zocl_slot->pr_isolation_freeze = 0x0;
+			zocl_slot->pr_isolation_unfreeze = 0x3;
+			if (of_property_read_u64(pdev->dev.of_node,
+					"xlnx,pr-isolation-addr",
+					&zocl_slot->pr_isolation_addr))
+				zocl_slot->pr_isolation_addr = 0;
+			if (of_property_read_bool(pdev->dev.of_node,
+						  "xlnx,pr-decoupler")) {
+				zocl_slot->pr_isolation_freeze = 0x1;
+				zocl_slot->pr_isolation_unfreeze = 0x0;
+			}
+		} else {
+			/* Work around for CR-1119382 issue.
+			 * ZOCL driver is crashing if it accessing the device tree node */
+			if (false) {
+				u32 prop_addr = 0;
+
+				if (of_property_read_u32(pdev->dev.of_node,
+							 "xlnx,pr-isolation-addr",
+							 &prop_addr))
+					zocl_slot->pr_isolation_addr = 0;
+				else
+					zocl_slot->pr_isolation_addr = prop_addr;
+			}
+		}
+
+		DRM_INFO("PR[%d] Isolation addr 0x%llx", i,
+			 zocl_slot->pr_isolation_addr);
+
+		zocl_slot->partial_overlay_id = -1;
+
+		zdev->pr_slot[i] = zocl_slot;
+	}
+
+	zdev->full_overlay_id  = -1;
+
+	return 0;
+}
+
+/**
+ * zocl_pr_slot_fini : PR Slot specific Cleanup
+ *
+ * @zdev: zocl device struct
+ *
+ */
+static void zocl_pr_slot_fini(struct drm_zocl_dev *zdev)
+{
+	struct drm_zocl_slot *zocl_slot = NULL;
+	int i = 0;
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+		if (zocl_slot) {
+			zocl_free_sections(zocl_slot);
+			mutex_destroy(&zocl_slot->slot_xclbin_lock);
+			zocl_xclbin_fini(zdev, zocl_slot);
+			kfree(zocl_slot);
+			zdev->pr_slot[i] = NULL;
+		}
+	}
+}
+
+/**
+ * Initialize the aparture and allocate memory for it.
+ *
+ * @param	zdev: device structure
+ *
+ * @return	0 on success, Error code on failure.
+ */
+static int zocl_aperture_init(struct drm_zocl_dev *zdev)
+{
+	struct addr_aperture *apts = NULL;
+	int i = 0;
+
+	zdev->apertures = kcalloc(MAX_APT_NUM, sizeof(struct addr_aperture),
+				 GFP_KERNEL);
+	if (!zdev->apertures) {
+		DRM_ERROR("Out of memory for Aperture\n");
+		return -ENOMEM;
+	}
+
+	apts = zdev->apertures;
+	/* Consider this magic number as uninitialized aperture identity */
+	for (i = 0; i < MAX_APT_NUM; ++i)
+		apts[i].addr = EMPTY_APT_VALUE;
+
+	zdev->num_apts = 0;
+
+	return 0;
+}
+
+/**
+ * Cleanup the aparture
+ *
+ * @param	zdev: device structure
+ *
+ */
+static void zocl_aperture_fini(struct drm_zocl_dev *zdev)
+{
+	/* Free aperture memory */
+	if (zdev->apertures)
+		vfree(zdev->apertures);
+
+	zdev->apertures = NULL;
+}
+
+
+/**
+ * get_reserved_mem_region - Get reserved memory region
+ *
+ * @dev: device struct
+ * @res: resource struct
+ *
+ * Returns 0 is get reserved memory resion successfully.
+ * Returns -EINVAL if not found.
+ */
+static int get_reserved_mem_region(struct device *dev, struct resource *res)
+{
+	struct device_node *np = NULL;
+	int ret;
+
+	np = of_parse_phandle(dev->of_node, "memory-region", 0);
+	if (!np)
+		return -EINVAL;
+
+	ret = of_address_to_resource(np, 0, res);
+	if (ret)
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * Find platform device by name
+ *
+ * @param	name: device name
+ *
+ * Returns a platform device. Returns NULL if not found.
+ */
+struct platform_device *zocl_find_pdev(char *name)
+{
+	struct device *dev;
+	struct platform_device *pdev;
+
+	dev = bus_find_device(&platform_bus_type, NULL, (void *)name,
+	    match_name);
+	if (!dev)
+		return NULL;
+
+	pdev = container_of(dev, struct platform_device, dev);
+	return pdev;
+}
+
+/**
+ * Set scheduler CU index in aperture
+ *
+ * @param	zdev:	zocl device struct
+ * @param	apt_idx: aperture index in the IP_LAYOUT ordering
+ * @param	cu_idx: CU index in the scheduler ordering
+ *
+ */
+void update_cu_idx_in_apt(struct drm_zocl_dev *zdev, int apt_idx, int cu_idx)
+{
+	struct addr_aperture *apts = zdev->apertures;
+
+	/* Actually, we should consider lock this.
+	 * So far, let do this without lock. Since the scheduler would only
+	 * update this when xclbin was changed.
+	 */
+	apts[apt_idx].cu_idx = cu_idx;
+}
+
+/**
+ * Get the index of the geiven phys address,
+ *		   if it is the start of an aperture
+ *
+ * @param	zdev: zocl device struct
+ * @param	addr: physical address of the aperture
+ *
+ * Returns the index if aperture was found, -EINVAL if not found.
+ *
+ */
+int get_apt_index_by_addr(struct drm_zocl_dev *zdev, phys_addr_t addr)
+{
+	struct addr_aperture *apts = zdev->apertures;
+	int i;
+
+	/* Haven't consider search efficiency yet. */
+	for (i = 0; i < zdev->num_apts; ++i)
+		if (apts[i].addr == addr)
+			break;
+
+	return (i == zdev->num_apts) ? -EINVAL : i;
+}
+
+/**
+ * Get the index of the geiven phys address,
+ *		   if it is the start of an aperture
+ *
+ * @param	zdev:	zocl device struct
+ * @param	cu_idx: CU index
+ *
+ * Returns the index if aperture was found, -EINVAL if not found.
+ *
+ */
+int get_apt_index_by_cu_idx(struct drm_zocl_dev *zdev, int cu_idx)
+{
+	struct addr_aperture *apts = zdev->apertures;
+	int i;
+
+	WARN_ON(cu_idx >= MAX_CU_NUM);
+	if (cu_idx >= MAX_CU_NUM)
+		return -EINVAL;
+
+	/* Haven't consider search efficiency yet. */
+	for (i = 0; i < zdev->num_apts; ++i)
+		if (apts[i].cu_idx == cu_idx)
+			break;
+
+	return (i == zdev->num_apts) ? -EINVAL : i;
+}
+
+/**
+ * Create a new CU subdevice. And try to attach to the driver. This will force
+ * cu probe to call.
+ *
+ * @param	zdev: zocl Device Instance
+ * @param	info: CU related information
+ *
+ * @return	0 on success, Error code on failure.
+ */
+int subdev_create_cu(struct device *dev, struct xrt_cu_info *info, struct platform_device **pdevp)
+{
+	struct platform_device *pldev;
+	struct resource res = {};
+	int ret;
+
+	pldev = platform_device_alloc("CU", PLATFORM_DEVID_AUTO);
+	if (!pldev) {
+		DRM_ERROR("Failed to alloc device CU\n");
+		return -ENOMEM;
+	}
+
+	/*
+	 * Only on U30 and some Versal platforms, the res_start is not zero.
+	 * But the situations are different,
+	 *
+	 *     On U30, CUs are assigned to lower 4GB address space.
+	 * Host doesn't know the CU base address, which is 0x80000000,
+	 * but zocl get it from device tree and store it in res_start.
+	 *
+	 *     On Versal, CUs are assigned to above 4GB address space.
+	 * Host knows the CU base address from xclbin.
+	 * But on some specific shells, zocl will get base address in
+	 * device tree. "Or" operation still works in this case.
+	 */
+	res.start = info->addr | zocl_get_zdev()->res_start;
+	res.end = res.start + info->size - 1;
+	res.flags = IORESOURCE_MEM;
+	ret = platform_device_add_resources(pldev, &res, 1);
+	if (ret) {
+		DRM_ERROR("Failed to add resource\n");
+		goto err;
+	}
+
+	ret = platform_device_add_data(pldev, info, sizeof(*info));
+	if (ret) {
+		DRM_ERROR("Failed to add data\n");
+		goto err;
+	}
+
+	pldev->dev.parent = dev;
+
+	ret = platform_device_add(pldev);
+	if (ret) {
+		DRM_ERROR("Failed to add device\n");
+		goto err;
+	}
+
+	/*
+	 * force probe to avoid dependence issue. if probing
+	 * failed, it could be the driver is not registered.
+	 */
+	ret = device_attach(&pldev->dev);
+	if (ret != 1) {
+		ret = -EINVAL;
+		DRM_ERROR("Failed to probe device\n");
+		goto err1;
+	}
+	*pdevp = pldev;
+
+	return 0;
+err1:
+	platform_device_del(pldev);
+err:
+	platform_device_put(pldev);
+	return ret;
+}
+
+/* This function destroy and remove the platform-level devices
+ * for all the CUs.
+ *
+ * @param	zdev: zocl Device Instance
+ *
+ */
+void subdev_destroy_cu(struct drm_zocl_dev *zdev)
+{
+	int i;
+
+	for (i = 0; i < MAX_CU_NUM; ++i) {
+		if (!zdev->cu_pldev[i])
+			continue;
+
+		/* Remove the platform-level device */
+		platform_device_del(zdev->cu_pldev[i]);
+		/* Destroy the platform device */
+		platform_device_put(zdev->cu_pldev[i]);
+		zdev->cu_pldev[i] = NULL;
+	}
+}
+
+/**
+ * Create a new SCU subdevice. And try to attach to the driver. This will force
+ * cu probe to call.
+ *
+ * @param	zdev: zocl Device Instance
+ * @param	info: SCU related information
+ *
+ * @return	0 on success, Error code on failure.
+ */
+int subdev_create_scu(struct device *dev, struct xrt_cu_info *info, struct platform_device **pdevp)
+{
+	struct platform_device *pldev;
+	int ret;
+
+	pldev = platform_device_alloc("SCU", PLATFORM_DEVID_AUTO);
+	if (!pldev) {
+		DRM_ERROR("Failed to alloc device SCU\n");
+		return -ENOMEM;
+	}
+
+	ret = platform_device_add_data(pldev, info, sizeof(*info));
+	if (ret) {
+		DRM_ERROR("Failed to add data\n");
+		goto err;
+	}
+
+	pldev->dev.parent = dev;
+
+	ret = platform_device_add(pldev);
+	if (ret) {
+		DRM_ERROR("Failed to add device\n");
+		goto err;
+	}
+
+	/*
+	 * force probe to avoid dependence issue. if probing
+	 * failed, it could be the driver is not registered.
+	 */
+	ret = device_attach(&pldev->dev);
+	if (ret != 1) {
+		ret = -EINVAL;
+		DRM_ERROR("Failed to probe device\n");
+		goto err1;
+	}
+	*pdevp = pldev;
+
+	return 0;
+err1:
+	platform_device_del(pldev);
+err:
+	platform_device_put(pldev);
+	return ret;
+}
+
+/**
+ * zocl_gem_create_object - Create drm_zocl_bo object instead of DRM CMA object.
+ *
+ * @dev: DRM device struct
+ * @size: This size was not use, just to match function prototype.
+ *
+ */
+struct drm_gem_object *
+zocl_gem_create_object(struct drm_device *dev, size_t size)
+{
+	struct drm_zocl_bo *bo = kzalloc(sizeof(struct drm_zocl_bo), GFP_KERNEL);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+	bo->gem_base.funcs = &zocl_gem_object_funcs;
+#endif
+	return (&bo->gem_base);
+}
+
+/* This callback function release GEM buffer objects and free memory associated
+ * with it. This function is also responsable for free up the memory for BOs.
+ *
+ * @param	obj:	GEM buffer object
+ *
+ */
+void zocl_free_bo(struct drm_gem_object *obj)
+{
+	struct drm_zocl_bo *zocl_obj;
+	struct drm_zocl_dev *zdev;
+	int npages;
+
+	if (IS_ERR(obj) || !obj)
+		return;
+
+	DRM_DEBUG("Freeing BO\n");
+	zocl_obj = to_zocl_bo(obj);
+	zdev = obj->dev->dev_private;
+
+	if (!zdev->domain) {
+		zocl_describe(zocl_obj);
+		if (zocl_obj->flags & ZOCL_BO_FLAGS_USERPTR)
+			zocl_free_userptr_bo(obj);
+		else if (zocl_obj->flags & ZOCL_BO_FLAGS_HOST_BO)
+			zocl_free_host_bo(obj);
+		else if (zocl_obj->flags & ZOCL_BO_FLAGS_CMA) {
+			/* Update memory usage statistics */
+			zocl_update_mem_stat(zdev, obj->size, -1,
+			    zocl_obj->mem_index);
+			/* free resources associated with a CMA GEM object */
+			drm_gem_cma_free_object(obj);
+
+		} else {
+			if (zocl_obj->mm_node) {
+				mutex_lock(&zdev->mm_lock);
+				drm_mm_remove_node(zocl_obj->mm_node);
+				mutex_unlock(&zdev->mm_lock);
+				kfree(zocl_obj->mm_node);
+				if (zocl_obj->vmapping) {
+					memunmap(zocl_obj->vmapping);
+					zocl_obj->vmapping = NULL;
+				}
+				zocl_update_mem_stat(zdev, obj->size, -1,
+				    zocl_obj->mem_index);
+			}
+			/* release GEM buffer object resources */
+			drm_gem_object_release(obj);
+			kfree(zocl_obj);
+		}
+
+		return;
+	}
+
+	npages = obj->size >> PAGE_SHIFT;
+	/* release GEM buffer object resources */
+	drm_gem_object_release(obj);
+
+	if (zocl_obj->vmapping)
+		vunmap(zocl_obj->vmapping);
+	zocl_obj->vmapping = NULL;
+
+	zocl_iommu_unmap_bo(obj->dev, zocl_obj);
+	if (zocl_obj->pages) {
+		if (zocl_bo_userptr(zocl_obj)) {
+#if KERNEL_VERSION(4, 15, 0) <= LINUX_VERSION_CODE
+			release_pages(zocl_obj->pages, npages);
+#else
+			release_pages(zocl_obj->pages, npages, 0);
+#endif
+			kvfree(zocl_obj->pages);
+		} else {
+			drm_gem_put_pages(obj, zocl_obj->pages, false, false);
+
+			/* Update memory usage statistics */
+			zocl_update_mem_stat(zdev, obj->size, -1,
+			    zocl_obj->mem_index);
+		}
+	}
+	if (zocl_obj->sgt)
+		sg_free_table(zocl_obj->sgt);
+	zocl_obj->sgt = NULL;
+	zocl_obj->pages = NULL;
+	kfree(zocl_obj);
+}
+
+/* This function memory map for GEM objects.
+ *
+ * @param	flip:	file data structure
+ * @param	vma:	struct to a virtual memory area
+ *
+ * @return	0 on success, Error code on failure.
+ */
+static int
+zocl_gem_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+	struct drm_gem_cma_object *cma_obj = NULL;
+	struct drm_gem_object *gem_obj;
+	struct drm_zocl_bo *bo;
+	dma_addr_t paddr;
+	pgprot_t prot;
+	int rc;
+
+	/**
+	 * drm_gem_mmap may modify the vma prot as non-cacheable.
+	 * We need to preserve this field and resume it in case
+	 * the BO is cacheable.
+	 */
+	prot = vma->vm_page_prot;
+
+	rc = drm_gem_mmap(filp, vma);
+
+	if (rc)
+		return rc;
+
+	/**
+	 * Clear the VM_PFNMAP flag that was set by drm_gem_mmap(),
+	 * and set the vm_pgoff (used as a fake buffer offset by DRM)
+	 * to 0 as we want to map the whole buffer.
+	 */
+	vma->vm_flags &= ~VM_PFNMAP;
+	vma->vm_pgoff = 0;
+
+	gem_obj = vma->vm_private_data;
+	bo = to_zocl_bo(gem_obj);
+
+	if (bo->flags & ZOCL_BO_FLAGS_CACHEABLE)
+		/**
+		 * Resume the protection field from mmap(). Most likely
+		 * it will be cacheable. If there is a case that mmap()
+		 * protection field explicitly tells us not to map with
+		 * cache enabled, we should comply with it and overwrite
+		 * the cacheable BO property.
+		 */
+		vma->vm_page_prot = prot;
+
+	if (bo->flags & ZOCL_BO_FLAGS_CMA) {
+		cma_obj = to_drm_gem_cma_obj(gem_obj);
+		paddr = cma_obj->paddr;
+	} else
+		paddr = bo->mm_node->start;
+
+	if ((!(bo->flags & ZOCL_BO_FLAGS_CMA)) ||
+	    (bo->flags & ZOCL_BO_FLAGS_CMA &&
+	    bo->flags & ZOCL_BO_FLAGS_CACHEABLE)) {
+		/* Map PL-DDR and cacheable CMA */
+		rc = remap_pfn_range(vma, vma->vm_start,
+		    paddr >> PAGE_SHIFT, vma->vm_end - vma->vm_start,
+		    vma->vm_page_prot);
+	} else {
+		/* Map non-cacheable CMA */
+		rc = dma_mmap_wc(cma_obj->base.dev->dev, vma, cma_obj->vaddr,
+		    paddr, vma->vm_end - vma->vm_start);
+	}
+
+	if (rc)
+		drm_gem_vm_close(vma);
+
+	return rc;
+}
+
+/* This function map two types of kernel address to user space.
+ * The first type is pysical registers of a hardware IP, like CUs.
+ * The second type is GEM buffer.
+ *
+ * @param	flip:	file data structure
+ * @param	vma:	struct to a virtual memory area
+ *
+ * @return	0 on success, Error code on failure.
+ */
+static int zocl_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+	struct drm_file     *priv = filp->private_data;
+	struct drm_device   *dev = priv->minor->dev;
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct addr_aperture *apts = zdev->apertures;
+	struct drm_zocl_bo  *bo = NULL;
+	unsigned long        vsize;
+	phys_addr_t          phy_addr;
+	int apt_idx;
+	int rc;
+
+	/* A GEM buffer object has a fake mmap offset start from page offset
+	 * DRM_FILE_PAGE_OFFSET_START. See drm_gem_init().
+	 * ZOCL_FILE_PAGE_OFFSET should equal to DRM_FILE_PAGE_OFFSET_START.
+	 * ZOCL_FILE_PAGE_OFFSET is 4GB for 64 bits system.
+	 */
+	if (likely(vma->vm_pgoff >= ZOCL_FILE_PAGE_OFFSET)) {
+		if (!zdev->domain)
+			return zocl_gem_mmap(filp, vma);
+
+		/* Map user's pages into his VM */
+		rc = drm_gem_mmap(filp, vma);
+		if (rc)
+			return rc;
+		/* vma->vm_private_data is set by drm_gem_mmap */
+		bo = to_zocl_bo(vma->vm_private_data);
+
+		bo->uaddr = vma->vm_start;
+		/* Map user's VA into IOMMU */
+		rc = zocl_iommu_map_bo(dev, bo);
+		if (rc)
+			return rc;
+		vma->vm_flags &= ~VM_PFNMAP;
+		vma->vm_flags |= VM_MIXEDMAP;
+		/* Reset the fake offset used to identify the BO */
+		vma->vm_pgoff = 0;
+		return 0;
+	}
+
+
+	/* Only allow user to map register ranges in apertures list.
+	 * Could not map from the middle of an aperture.
+	 */
+	apt_idx = vma->vm_pgoff;
+	if (apt_idx < 0 || apt_idx >= zdev->num_apts) {
+		DRM_ERROR("The offset is not in the apertures list\n");
+		return -EINVAL;
+	}
+	phy_addr = apts[apt_idx].addr;
+	vma->vm_pgoff = phy_addr >> PAGE_SHIFT;
+
+	vsize = vma->vm_end - vma->vm_start;
+	if (vsize > zdev->apertures[apt_idx].size)
+		return -EINVAL;
+
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	vma->vm_flags |= VM_IO;
+	vma->vm_flags |= VM_RESERVED;
+
+	vma->vm_ops = &reg_physical_vm_ops;
+	rc = io_remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
+				vsize, vma->vm_page_prot);
+
+	return rc;
+}
+
+/**
+ * Registering callback for fault handler.
+ *
+ * @param	vmf:	vm page fault instance
+ *
+ * @return	VM_FAULT_NOPAGE on success, Error code on failure.
+ */
+static vm_fault_t zocl_bo_fault(struct vm_fault *vmf)
+{
+	struct vm_area_struct *vma = vmf->vma;
+	struct drm_gem_object *obj = vma->vm_private_data;
+	struct drm_zocl_bo *bo = to_zocl_bo(obj);
+	struct drm_zocl_dev *zdev = obj->dev->dev_private;
+	struct page *page;
+	pgoff_t offset;
+	int err;
+
+	if (!zdev->domain)
+		return 0;
+
+	if (!bo->pages)
+		return VM_FAULT_SIGBUS;
+
+	offset = ((unsigned long)vmf->address - vma->vm_start) >> PAGE_SHIFT;
+	page = bo->pages[offset];
+
+	err = vm_insert_page(vma, (unsigned long)vmf->address, page);
+	switch (err) {
+	case -EAGAIN:
+	case 0:
+	case -ERESTARTSYS:
+	case -EINTR:
+	case -EBUSY:
+		return VM_FAULT_NOPAGE;
+	case -ENOMEM:
+		return VM_FAULT_OOM;
+	}
+	return VM_FAULT_SIGBUS;
+}
+
+/**
+ * Driver callback when a new &struct drm_file is opened.
+ * This function will create a new client for this device
+ *
+ * @param	dev:	DRM device structure
+ * @param	flip:	DRM file private data
+ *
+ * @return	0 on success, Error code on failure.
+ */
+static int zocl_client_open(struct drm_device *dev, struct drm_file *filp)
+{
+	return zocl_create_client(dev->dev, &filp->driver_priv);
+}
+
+/**
+ * Driver callback when a new &struct drm_file is closed.
+ * This function will cleanup driver-private data structures
+ * allocated in @open and destroy the client.
+ *
+ * @param	dev:	DRM device structure
+ * @param	flip:	DRM file private data
+ *
+ * @return	0 on success, Error code on failure.
+ */
+static void zocl_client_release(struct drm_device *dev, struct drm_file *filp)
+{
+	return zocl_destroy_client(filp->driver_priv);
+}
+
+/**
+ * Register a poll callback function for this driver
+ *
+ * @param	flip:	file data structure
+ * @param	wait:	poll table
+ *
+ * @return	POLLIN on success, 0 on failure.
+ */
+static unsigned int zocl_poll(struct file *filp, poll_table *wait)
+{
+	return zocl_poll_client(filp, wait);
+}
+
+/**
+ * Initialize iommu domain for this device
+ *
+ * @param	zdev: zocl Device Instance
+ * @param	pdev: Platform Device Instance
+ *
+ * @return	0 on success, Error code on failure.
+ */
+static int zocl_iommu_init(struct drm_zocl_dev *zdev,
+		struct platform_device *pdev)
+{
+	struct iommu_domain_geometry *geometry;
+	u64 start, end;
+	int ret;
+
+	zdev->domain = iommu_domain_alloc(&platform_bus_type);
+	if (!zdev->domain)
+		return -ENOMEM;
+
+	ret = iommu_attach_device(zdev->domain, &pdev->dev);
+	if (ret) {
+		DRM_INFO("IOMMU attach device failed. ret(%d)\n", ret);
+		iommu_domain_free(zdev->domain);
+		zdev->domain = NULL;
+		return ret;
+	}
+
+	geometry = &zdev->domain->geometry;
+	start = geometry->aperture_start;
+	end = geometry->aperture_end;
+
+	DRM_INFO("IOMMU aperture initialized (%#llx-%#llx)\n",
+				start, end);
+
+	return 0;
+}
+
+const struct vm_operations_struct zocl_bo_vm_ops = {
+	.fault = zocl_bo_fault,
+	.open  = drm_gem_vm_open,
+	.close = drm_gem_vm_close,
+};
+
+static const struct drm_ioctl_desc zocl_ioctls[] = {
+	DRM_IOCTL_DEF_DRV(ZOCL_CREATE_BO, zocl_create_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_USERPTR_BO, zocl_userptr_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_GET_HOST_BO, zocl_get_hbo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_MAP_BO, zocl_map_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_SYNC_BO, zocl_sync_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_INFO_BO, zocl_info_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_PWRITE_BO, zocl_pwrite_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_PREAD_BO, zocl_pread_bo_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_EXECBUF, zocl_execbuf_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_READ_AXLF, zocl_read_axlf_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_SK_GETCMD, zocl_sk_getcmd_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_SK_CREATE, zocl_sk_create_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_SK_REPORT, zocl_sk_report_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_INFO_CU, zocl_info_cu_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_CTX, zocl_ctx_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_ERROR_INJECT, zocl_error_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_AIE_FD, zocl_aie_fd_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_AIE_RESET, zocl_aie_reset_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_AIE_GETCMD, zocl_aie_getcmd_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_AIE_PUTCMD, zocl_aie_putcmd_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+	DRM_IOCTL_DEF_DRV(ZOCL_AIE_FREQSCALE, zocl_aie_freqscale_ioctl,
+			DRM_AUTH|DRM_UNLOCKED|DRM_RENDER_ALLOW),
+};
+
+static const struct file_operations zocl_driver_fops = {
+	.owner          = THIS_MODULE,
+	.open           = drm_open,
+	.mmap           = zocl_mmap,
+	.poll           = zocl_poll,
+	.read           = drm_read,
+	.unlocked_ioctl = drm_ioctl,
+	.release        = drm_release,
+};
+
+static struct drm_driver zocl_driver = {
+#if KERNEL_VERSION(5, 4, 0) > LINUX_VERSION_CODE
+	.driver_features           = DRIVER_GEM | DRIVER_PRIME | DRIVER_RENDER,
+#else
+	.driver_features           = DRIVER_GEM | DRIVER_RENDER,
+#endif
+	.open                      = zocl_client_open,
+	.postclose                 = zocl_client_release,
+#if LINUX_VERSION_CODE < KERNEL_VERSION(5, 11, 0)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 7, 0)
+	.gem_free_object_unlocked  = zocl_free_bo,
+#else
+	.gem_free_object           = zocl_free_bo,
+#endif
+
+	.gem_vm_ops                = &zocl_bo_vm_ops,
+	.gem_prime_get_sg_table    = drm_gem_cma_prime_get_sg_table,
+	.gem_prime_vmap            = drm_gem_cma_prime_vmap,
+	.gem_prime_vunmap          = drm_gem_cma_prime_vunmap,
+	.gem_prime_export          = drm_gem_prime_export,
+#endif
+
+	.gem_create_object         = zocl_gem_create_object,
+	.prime_handle_to_fd        = drm_gem_prime_handle_to_fd,
+	.prime_fd_to_handle        = drm_gem_prime_fd_to_handle,
+	.gem_prime_import          = zocl_gem_import,
+	.gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
+	.gem_prime_mmap            = drm_gem_prime_mmap,
+	.ioctls                    = zocl_ioctls,
+	.num_ioctls                = ARRAY_SIZE(zocl_ioctls),
+	.fops                      = &zocl_driver_fops,
+	.name                      = ZOCL_DRIVER_NAME,
+	.desc                      = ZOCL_DRIVER_DESC,
+	.date                      = driver_date,
+};
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 11, 0)
+const struct drm_gem_object_funcs zocl_gem_object_funcs = {
+	.free = zocl_free_bo,
+	.vm_ops = &zocl_bo_vm_ops,
+	.get_sg_table = drm_gem_cma_get_sg_table,
+	.vmap = drm_gem_cma_vmap,
+	.export = drm_gem_prime_export,
+};
+
+const struct drm_gem_object_funcs zocl_cma_default_funcs = {
+	.free = zocl_free_bo,
+	.get_sg_table = drm_gem_cma_get_sg_table,
+	.vm_ops = &zocl_bo_vm_ops,
+};
+#endif
+static const struct zdev_data zdev_data_mpsoc = {
+	.fpga_driver_name = "pcap",
+};
+
+static const struct zdev_data zdev_data_versal = {
+	.fpga_driver_name = "versal_fpga"
+};
+
+static const struct of_device_id zocl_drm_of_match[] = {
+	{ .compatible = "xlnx,zocl", .data = &zdev_data_mpsoc},
+	{ .compatible = "xlnx,zoclsvm", .data = &zdev_data_mpsoc},
+	{ .compatible = "xlnx,zocl-ert", .data = &zdev_data_mpsoc},
+	{ .compatible = "xlnx,zocl-versal", .data = &zdev_data_versal},
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, zocl_drm_of_match);
+
+/*
+ *
+ * Initialization of Xilinx openCL DRM platform device.
+ *
+ * @param        pdev: Platform Device Instance
+ *
+ * @return       0 on success, Error code on failure.
+ *
+ */
+static int zocl_drm_platform_probe(struct platform_device *pdev)
+{
+	const struct of_device_id *id;
+	struct drm_device *drm;
+	struct drm_zocl_dev	*zdev;
+	struct platform_device *subdev;
+	struct resource res_mem;
+	struct resource *res;
+	struct device_node *fnode;
+	int index;
+	int irq;
+	int ret;
+	int year, mon, day;
+
+	id = of_match_node(zocl_drm_of_match, pdev->dev.of_node);
+	DRM_INFO("Probing for %s\n", id->compatible);
+
+	/* Create zocl device and initial */
+	zdev = devm_kzalloc(&pdev->dev, sizeof(*zdev), GFP_KERNEL);
+	if (!zdev)
+		return -ENOMEM;
+
+	zdev->zdev_data_info = id->data;
+	INIT_LIST_HEAD(&zdev->ctx_list);
+
+	/* Record and get IRQ number */
+	for (index = 0; index < MAX_CU_NUM; index++) {
+		irq = platform_get_irq(pdev, index);
+		if (irq < 0)
+			break;
+		DRM_DEBUG("CU(%d) IRQ %d\n", index, irq);
+		zdev->irq[index] = irq;
+	}
+	zdev->cu_num = index;
+
+	/* set to 0xFFFFFFFF(32bit) or 0xFFFFFFFFFFFFFFFF(64bit) */
+	zdev->host_mem = (phys_addr_t) -1;
+	zdev->host_mem_len = 0;
+	/* Work around for CR-1119382 issue.
+	 * ZOCL driver is crashing if it accessing the device tree node */
+	if (ZOCL_PLATFORM_ARM64) {
+		/* If reserved memory region are not found, just keep going */
+		ret = get_reserved_mem_region(&pdev->dev, &res_mem);
+		if (!ret) {
+			DRM_INFO("Reserved memory for host at 0x%lx, size 0x%lx\n",
+				 (unsigned long)res_mem.start,
+				 (unsigned long)resource_size(&res_mem));
+			zdev->host_mem = res_mem.start;
+			zdev->host_mem_len = resource_size(&res_mem);
+		}
+	}
+	mutex_init(&zdev->mm_lock);
+	INIT_LIST_HEAD(&zdev->zm_list_head);
+
+	subdev = zocl_find_pdev("ert_hw");
+	if (subdev) {
+		DRM_INFO("ert_hw found: 0x%llx\n", (uint64_t)(uintptr_t)subdev);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (res) {
+			zdev->res_start = res->start;
+		}
+
+		zdev->res_start = res->start;
+		zdev->ert = (struct zocl_ert_dev *)platform_get_drvdata(subdev);
+		//ert_hw is present only for PCIe + PS devices (ex: U30,VCK5000
+		//Dont enable new kds for those devices
+	}
+
+	subdev = zocl_find_pdev("reset_ps");
+	if (subdev) {
+		DRM_INFO("reset_ps found: 0x%llx\n", (uint64_t)(uintptr_t)subdev);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (!res) {
+			DRM_ERROR("The base address of reset_ps is not found or 0\n");
+			return -EINVAL;
+		}
+
+		zdev->watchdog = platform_get_drvdata(subdev);
+	}
+
+	/* Work around for CR-1119382 issue.
+	 * ZOCL driver is crashing if it accessing the device tree node */
+	if (ZOCL_PLATFORM_ARM64) {
+		/* For Non PR platform, there is not need to have FPGA manager
+		 * For PR platform, the FPGA manager is required. No good way to
+		 * determin if it is a PR platform at probe.
+		 */
+		fnode = of_find_node_by_name(NULL,
+				     zdev->zdev_data_info->fpga_driver_name);
+		if (fnode) {
+			zdev->fpga_mgr = of_fpga_mgr_get(fnode);
+			if (IS_ERR(zdev->fpga_mgr))
+				zdev->fpga_mgr = NULL;
+			DRM_INFO("FPGA programming device %s founded.\n",
+				 zdev->zdev_data_info->fpga_driver_name);
+			of_node_put(fnode);
+		}
+	}
+
+	/* Initialize Aperture */
+	ret = zocl_aperture_init(zdev);
+	if (ret)
+		goto err_apt;
+
+	/* Initialzie Slot */
+	ret = zocl_pr_slot_init(zdev, pdev);
+	if (ret)
+		goto err_drm;
+
+	/* Initialzie IOMMU */
+	if (iommu_present(&platform_bus_type)) {
+		/*
+		 * Note: we ignore the return value of zocl_iommu_init().
+		 * In the case of failing to initialize iommu, zocl
+		 * driver will keep working with iommu disabled.
+		 */
+		(void) zocl_iommu_init(zdev, pdev);
+	}
+
+	platform_set_drvdata(pdev, zdev);
+
+	/* Work around for CR-1119382 issue.
+	 * ZOCL driver is crashing if it accessing the device tree node */
+	if (ZOCL_PLATFORM_ARM64) {
+		sscanf(XRT_DRIVER_VERSION, "%d.%d.%d",
+		       &zocl_driver.major,
+		       &zocl_driver.minor,
+		       &zocl_driver.patchlevel);
+		sscanf(XRT_DATE, "%d-%d-%d ", &year, &mon, &day);
+		//e.g HASH_DATE ==> Wed, 4 Nov 2020 08:46:44 -0800
+		//e.g XRT_DATE ==> 2020-11-04
+		snprintf(driver_date, sizeof(driver_date),
+			 "%d%02d%02d", year, mon, day);
+	}
+	/* Create and register DRM device */
+	drm = drm_dev_alloc(&zocl_driver, &pdev->dev);
+	if (IS_ERR(drm)) {
+		ret = PTR_ERR(drm);
+		goto err_drm;
+	}
+
+	ret = drm_dev_register(drm, 0);
+	if (ret)
+		goto err_sysfs;
+
+	/* During attach, we don't request dma channel */
+	zdev->zdev_dma_chan = NULL;
+
+	/* doen with zdev initialization */
+	drm->dev_private = zdev;
+	zdev->ddev       = drm;
+
+	ret = zocl_init_error(zdev);
+	if (ret)
+		goto err_sysfs;
+
+	mutex_init(&zdev->aie_lock);
+
+	/* Initial sysfs */
+	rwlock_init(&zdev->attr_rwlock);
+	ret = zocl_init_sysfs(drm->dev);
+	if (ret)
+		goto err_err;
+
+	/* Now initial kds */
+	ret = zocl_init_sched(zdev);
+	if (ret)
+		goto err_sched;
+
+	return 0;
+
+/* error out in exact reverse order of init */
+err_sched:
+	zocl_fini_sysfs(drm->dev);
+err_err:
+	mutex_destroy(&zdev->aie_lock);
+	zocl_fini_error(zdev);
+err_sysfs:
+	ZOCL_DRM_DEV_PUT(drm);
+err_drm:
+	zocl_pr_slot_fini(zdev);
+err_apt:
+	zocl_aperture_fini(zdev);
+	return ret;
+}
+
+/*
+ *
+ * Exit Xilinx openCL DRM platform device.
+ *
+ * @param        pdev: Platform Device Instance
+ *
+ * @return       0 on success, Error code on failure.
+ *
+ */
+static int zocl_drm_platform_remove(struct platform_device *pdev)
+{
+	struct drm_zocl_dev *zdev = platform_get_drvdata(pdev);
+	struct drm_device *drm = zdev->ddev;
+
+	/* Cleanup of iommu domain, if exists */
+	if (zdev->domain) {
+		iommu_detach_device(zdev->domain, drm->dev);
+		iommu_domain_free(zdev->domain);
+	}
+
+	/* If dma channel has been requested, make sure it is released */
+	if (zdev->zdev_dma_chan) {
+		dma_release_channel(zdev->zdev_dma_chan);
+		zdev->zdev_dma_chan = NULL;
+	}
+
+	if (zdev->fpga_mgr)
+		fpga_mgr_put(zdev->fpga_mgr);
+
+	zocl_clear_mem(zdev);
+	mutex_destroy(&zdev->mm_lock);
+	zocl_pr_slot_fini(zdev);
+	zocl_destroy_aie(zdev);
+	mutex_destroy(&zdev->aie_lock);
+	zocl_fini_sysfs(drm->dev);
+	zocl_fini_error(zdev);
+
+	zocl_fini_sched(zdev);
+
+	if (zdev->apertures)
+		kfree(zdev->apertures);
+
+	drm_dev_unregister(drm);
+	ZOCL_DRM_DEV_PUT(drm);
+
+	return 0;
+}
+
+static struct platform_driver zocl_drm_private_driver = {
+	.probe			= zocl_drm_platform_probe,
+	.remove			= zocl_drm_platform_remove,
+	.driver			= {
+		.name	        = "zocl-drm",
+		.of_match_table	= zocl_drm_of_match,
+	},
+};
+
+static struct platform_driver *drivers[] = {
+	&zocl_watchdog_driver,
+	&zocl_ospi_versal_driver,
+	&cu_driver,
+	&scu_driver,
+	&zocl_drm_private_driver,
+	&zocl_csr_intc_driver,
+	&zocl_xgq_intc_driver,
+	&zocl_cu_xgq_driver,
+	&zocl_ctrl_ert_driver,
+	&zocl_rpu_channel_driver,
+};
+
+static int __init zocl_init(void)
+{
+	int ret = 0, total = ARRAY_SIZE(drivers), i;
+
+	/* HACK: fix ert driver. */
+	if (!enable_xgq_ert) {
+		for (i = 0; i < total && ret >= 0; i++) {
+			if (drivers[i] == &zocl_ctrl_ert_driver) {
+				drivers[i] = &zocl_ert_driver;
+				break;
+			}
+		}
+	}
+
+	for (i = 0; i < total && ret >= 0; i++)
+		ret = platform_driver_register(drivers[i]);
+	if (ret >= 0)
+		return 0;
+
+	/* Failed to register some drivers, undo. */
+	while (--i >= 0)
+		platform_driver_unregister(drivers[i]);
+	return ret;
+}
+module_init(zocl_init);
+
+static void __exit zocl_exit(void)
+{
+	int i = ARRAY_SIZE(drivers);
+
+	while (--i >= 0)
+		platform_driver_unregister(drivers[i]);
+}
+module_exit(zocl_exit);
+
+MODULE_VERSION(XRT_DRIVER_VERSION);
+
+MODULE_DESCRIPTION(ZOCL_DRIVER_DESC);
+MODULE_AUTHOR("Sonal Santan <sonal.santan@xilinx.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_error.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_error.c
@@ -0,0 +1,130 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu <yliu@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/mutex.h>
+
+#include "zocl_error.h"
+#include "zocl_drv.h"
+
+static void
+zocl_clear_all_error_record(struct drm_zocl_dev *zdev)
+{
+	struct zocl_error *zer = &zdev->zdev_error;
+
+	write_lock(&zdev->attr_rwlock);
+
+	memset(zer->ze_err, 0, sizeof(struct zocl_err_record) * zer->ze_num);
+	zer->ze_num = 0;
+
+	write_unlock(&zdev->attr_rwlock);
+}
+
+int
+zocl_insert_error_record(struct drm_zocl_dev *zdev, xrtErrorCode err_code)
+{
+	struct zocl_error *zer = &zdev->zdev_error;
+	u64 timestamp = ktime_to_ns(ktime_get_real());
+	enum xrtErrorClass class;
+	int i;
+
+	write_lock(&zdev->attr_rwlock);
+
+	if (zer->ze_num == zer->ze_cap) {
+		DRM_INFO("Error cache is full. "
+		    "No more asynchronous error will be recorded.\n");
+		write_unlock(&zdev->attr_rwlock);
+		return -ENOSPC;
+	}
+
+	/*
+	 * We only record one error for each error class.
+	 * If we can find existing error class, replace it;
+	 * Otherwise, record the error at the end.
+	 */
+	class = XRT_ERROR_CLASS(err_code);
+	for (i = 0; i < zer->ze_num; i++) {
+		if (class == XRT_ERROR_CLASS(zer->ze_err[i].zer_err_code))
+			break;
+	}
+
+	zer->ze_err[i].zer_err_code = err_code;
+	zer->ze_err[i].zer_ts = timestamp;
+	if (i == zer->ze_num)
+		zer->ze_num++;
+
+	write_unlock(&zdev->attr_rwlock);
+
+	return 0;
+}
+
+int
+zocl_inject_error(struct drm_zocl_dev *zdev, void *data,
+		struct drm_file *filp)
+{
+	struct drm_zocl_error_inject *args = data;
+	xrtErrorCode err_code;
+	int ret = 0;
+
+	switch (args->err_ops) {
+	case ZOCL_ERROR_OP_INJECT:
+		err_code = XRT_ERROR_CODE_BUILD(
+		    args->err_num,
+		    args->err_driver,
+		    args->err_severity,
+		    args->err_module,
+		    args->err_class
+		    );
+
+		ret = zocl_insert_error_record(zdev, err_code);
+		break;
+
+	case ZOCL_ERROR_OP_CLEAR_ALL:
+		zocl_clear_all_error_record(zdev);
+		break;
+
+	default:
+		DRM_ERROR("Unknow error ioctl operation code: %d\n",
+		    args->err_ops);
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+int
+zocl_init_error(struct drm_zocl_dev *zdev)
+{
+	struct zocl_error *zer = &zdev->zdev_error;
+
+	zer->ze_num = 0;
+	zer->ze_cap = ZOCL_DEFAULT_ERROR_CAPACITY;
+
+	zer->ze_err = vzalloc(zer->ze_cap * sizeof(struct zocl_err_record));
+	if (!zer->ze_err) {
+		zer->ze_cap = 0;
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+void
+zocl_fini_error(struct drm_zocl_dev *zdev)
+{
+	struct zocl_error *zer = &zdev->zdev_error;
+
+	vfree(zer->ze_err);
+	zer->ze_err = NULL;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_ert.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_ert.c
@@ -0,0 +1,314 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2016-2020 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+#include "ert.h"
+#include "zocl_ert.h"
+#include "zocl_util.h"
+#include "zocl_mailbox.h"
+
+#define ert_err(pdev, fmt, args...)  \
+	zocl_err(&pdev->dev, fmt"\n", ##args)
+#define ert_info(pdev, fmt, args...)  \
+	zocl_info(&pdev->dev, fmt"\n", ##args)
+#define ert_dbg(pdev, fmt, args...)  \
+	zocl_dbg(&pdev->dev, fmt"\n", ##args)
+
+struct ert_packet *
+get_packet(struct ert_packet *packet, u32 idx, u32 size)
+{
+	char *bytes = (char *)packet;
+
+	return (struct ert_packet *)(bytes + idx * size);
+}
+
+static void
+ert_mpsoc_init(struct zocl_ert_dev *ert)
+{
+	return;
+}
+
+static void
+ert_mpsoc_fini(struct zocl_ert_dev *ert)
+{
+	return;
+}
+
+static void
+ert_mpsoc_config(struct zocl_ert_dev *ert, struct ert_configure_cmd *cfg)
+{
+	char *ert_hw = ert->hw_ioremap;
+
+	/* Set slot size(4K) */
+	iowrite32(cfg->slot_size / 4, ert_hw + ERT_CQ_SLOT_SIZE_REG);
+
+	/* CU offset in shift value */
+	iowrite32(cfg->cu_shift, ert_hw + ERT_CU_OFFSET_REG);
+
+	/* Number of command slots */
+	iowrite32(CQ_SIZE / cfg->slot_size, ert_hw + ERT_CQ_NUM_OF_SLOTS_REG);
+
+	/* CU physical address */
+	/* TODO: Think about how to make the address mapping correct */
+	iowrite32(0x81800000/4, ert_hw + ERT_CU_BASE_ADDR_REG);
+
+	/* Command queue physical address */
+	iowrite32(0x80190000/4, ert_hw + ERT_CQ_BASE_ADDR_REG);
+
+	/* Number of CUs */
+	iowrite32(cfg->num_cus, ert_hw + ERT_NUM_OF_CU_REG);
+
+	/* Enable/Disable CU_DMA module */
+	iowrite32(cfg->cu_dma, ert_hw + ERT_CU_DMA_ENABLE);
+
+	if (cfg->cq_int)
+		iowrite32(1, ert_hw + ERT_CQ_STATUS_ENABLE);
+	else
+		iowrite32(0, ert_hw + ERT_CQ_STATUS_ENABLE);
+
+	/* Enable device to host interrupts */
+	iowrite32(1, ert_hw + ERT_HOST_INT_ENABLE);
+}
+
+static u32 cq_status[4];
+
+static struct ert_packet *
+ert_mpsoc_next(struct zocl_ert_dev *ert, struct ert_packet *pkg, int *idx_ret)
+{
+	char *ert_hw = ert->hw_ioremap;
+	int slot_idx, mask_idx, slot_tmp;
+	int slot_sz;
+	int i, found;
+	u64 slot_info;
+
+	slot_sz = ioread32(ert_hw + ERT_CQ_SLOT_SIZE_REG) * 4;
+	/* Calculate current slot index */
+	if (pkg == NULL) {
+		slot_idx = -1;
+		/* ERT CQ STATUS register is W/COR
+		 * Store all of the status
+		 * registers when getting the first command.
+		 */
+		cq_status[0] = ioread32(ert_hw + ERT_CQ_STATUS_REG0);
+		cq_status[1] = ioread32(ert_hw + ERT_CQ_STATUS_REG1);
+		cq_status[2] = ioread32(ert_hw + ERT_CQ_STATUS_REG2);
+		cq_status[3] = ioread32(ert_hw + ERT_CQ_STATUS_REG3);
+	} else {
+		/* ERT mode is only for 64 bits system */
+		slot_info = ((u64)pkg - (u64)ert->cq_ioremap);
+		do_div(slot_info, slot_sz);
+		slot_idx = slot_info;
+	}
+
+	/* Get mask index and local slot index for the next commmand */
+	slot_idx += 1;
+	mask_idx = slot_idx >> 5;
+	slot_tmp = slot_idx % 32;
+
+	found = 0;
+	for (i = mask_idx; i < 4; i++) {
+		while (cq_status[i] && (slot_tmp < 32)) {
+			if (cq_status[i] & (1 << slot_tmp)) {
+				found = 1;
+				cq_status[i] ^= (1 << slot_tmp);
+				break;
+			}
+			slot_tmp++;
+			slot_idx++;
+		}
+		if (found)
+			break;
+
+		slot_tmp = 0;
+	}
+
+	if (found) {
+		*idx_ret = slot_idx;
+		return get_packet(ert->cq_ioremap, slot_idx, slot_sz);
+	} else {
+		*idx_ret = -1;
+		return NULL;
+	}
+}
+
+static void ert_mpsoc_notify_host(struct zocl_ert_dev *ert, int slot_idx)
+{
+	u32 mask_idx = slot_idx >> 5;
+	u32 csr_offset = ERT_STATUS_REG + (mask_idx<<2);
+	u32 pos = slot_idx % 32;
+
+	iowrite32(1 << pos, ert->hw_ioremap + csr_offset);
+}
+
+/* ert versal ops */
+static void
+ert_versal_init(struct zocl_ert_dev *ert)
+{
+	return;
+}
+
+static void
+ert_versal_fini(struct zocl_ert_dev *ert)
+{
+	return;
+}
+
+static void
+ert_versal_config(struct zocl_ert_dev *ert, struct ert_configure_cmd *cfg)
+{
+	return;
+}
+
+static struct ert_packet *
+ert_versal_next(struct zocl_ert_dev *ert, struct ert_packet *pkg, int *idx_ret)
+{
+	return NULL;
+}
+
+static void
+ert_versal_notify_host(struct zocl_ert_dev *ert, int slot_idx)
+{
+	struct mailbox mbx;
+	u32 status = (u32)-1;
+	mbx.mbx_regs = (struct mailbox_reg *)ert->hw_ioremap;
+
+	while (1) {
+		status = zocl_mailbox_status(&mbx);
+		if (status == (u32)-1) {
+			ert_err(ert->pdev, "mailbox error: 0x%x", status);
+			break;
+		}
+
+		if ((status & MBX_STATUS_FULL) == 0) {
+			zocl_mailbox_set(&mbx, slot_idx);
+			break;
+		}
+	}
+}
+
+static void
+update_cmd(struct zocl_ert_dev *ert, int idx, void *data, int sz)
+{
+	struct ert_packet *pkg;
+	char *ert_hw = ert->hw_ioremap;
+	int slot_sz;
+
+	slot_sz = ioread32(ert_hw + ERT_CQ_SLOT_SIZE_REG) * 4;
+
+	pkg = ert->cq_ioremap + idx * slot_sz;
+	memcpy_toio(pkg->data, data, sz);
+}
+
+static struct zocl_ert_ops mpsoc_ops = {
+	.init         = ert_mpsoc_init,
+	.fini         = ert_mpsoc_fini,
+	.config       = ert_mpsoc_config,
+	.get_next_cmd = ert_mpsoc_next,
+	.notify_host  = ert_mpsoc_notify_host,
+	.update_cmd   = update_cmd,
+};
+
+static struct zocl_ert_ops versal_ops = {
+	.init         = ert_versal_init,
+	.fini         = ert_versal_fini,
+	.config       = ert_versal_config,
+	.get_next_cmd = ert_versal_next,
+	.notify_host  = ert_versal_notify_host,
+	.update_cmd   = update_cmd,
+};
+
+static const struct zocl_ert_info mpsoc_ert_info = {
+	.ops   = &mpsoc_ops,
+};
+
+static const struct zocl_ert_info versal_ert_info = {
+	.ops   = &versal_ops,
+};
+
+static const struct of_device_id zocl_ert_of_match[] = {
+	{ .compatible = "xlnx,embedded_sched",
+	  .data = &mpsoc_ert_info,
+	},
+	{ .compatible = "xlnx,embedded_sched_versal",
+	  .data = &versal_ert_info,
+	},
+	{ /* end of table */ },
+};
+
+MODULE_DEVICE_TABLE(of, zocl_ert_of_match);
+
+static int zocl_ert_probe(struct platform_device *pdev)
+{
+	struct zocl_ert_dev *ert;
+	const struct of_device_id *id;
+	struct resource *res;
+	const struct zocl_ert_info *info;
+	void __iomem *map;
+
+	id = of_match_node(zocl_ert_of_match, pdev->dev.of_node);
+	ert_info(pdev, "Probing for %s", id->compatible);
+
+	ert = devm_kzalloc(&pdev->dev, sizeof(*ert), GFP_KERNEL);
+	ert->pdev = pdev;
+
+	info = of_device_get_match_data(&pdev->dev);
+	ert->ops = info->ops;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, ZOCL_ERT_HW_RES);
+	map = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(map)) {
+		ert_err(pdev, "Failed to map ERT HW registers: %0lx",
+				PTR_ERR(map));
+		return PTR_ERR(map);
+	}
+	ert->hw_ioremap = map;
+	ert_info(pdev, "IP(embedded_scheduler_hw) IO start %lx, end %lx",
+	      (unsigned long)res->start, (unsigned long)res->end);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, ZOCL_ERT_CQ_RES);
+	map = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(map)) {
+		ert_err(pdev, "Failed to map Command Queue: %0lx",
+				PTR_ERR(map));
+		return PTR_ERR(map);
+	}
+	ert->cq_ioremap = map;
+	ert_info(pdev, "Command Queue IO start %lx, end %lx",
+		(unsigned long)res->start, (unsigned long)res->end);
+
+	/* Initial CQ */
+	memset_io(ert->cq_ioremap, 0, res->end - res->start + 1);
+
+	ert->irq[ERT_CQ_IRQ] = platform_get_irq(pdev, ERT_CQ_IRQ);
+	ert->irq[ERT_CU_IRQ] = platform_get_irq(pdev, ERT_CU_IRQ);
+	ert_info(pdev, "CQ irq %d, CU irq %d", ert->irq[ERT_CQ_IRQ],
+			ert->irq[ERT_CU_IRQ]);
+
+	if (info->ops == NULL) {
+		ert_err(pdev, "zocl ert probe failed due to ops has not been set");
+		return -ENODEV;
+	}
+	platform_set_drvdata(pdev, ert);
+	return 0;
+}
+
+static int zocl_ert_remove(struct platform_device *pdev)
+{
+	ert_dbg(pdev, "Release resource");
+	return 0;
+}
+
+struct platform_driver zocl_ert_driver = {
+	.driver = {
+		.name = ZOCL_ERT_NAME,
+		.of_match_table = zocl_ert_of_match,
+	},
+	.probe  = zocl_ert_probe,
+	.remove = zocl_ert_remove,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_ioctl.c
@@ -0,0 +1,139 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Sonal Santan <sonal.santan@xilinx.com>
+ *    Jan Stephan  <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "sched_exec.h"
+#include "zocl_xclbin.h"
+#include "zocl_error.h"
+
+/*
+ * read_axlf and ctx should be protected by slot_xclbin_lock exclusively.
+ */
+int
+zocl_read_axlf_ioctl(struct drm_device *ddev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_axlf *axlf_obj = data;
+	struct drm_zocl_dev *zdev = ZOCL_GET_ZDEV(ddev);
+	struct sched_client_ctx *client = filp->driver_priv;
+
+	return zocl_xclbin_read_axlf(zdev, axlf_obj, client);
+}
+
+/*
+ * Block comment for context switch.
+ * The read_axlf_ioctl can happen without calling open context, we need to use mutex
+ * lock to exclude access between read_axlf_ioctl and zocl_ctx_ioctl. At one
+ * time, only one operation can be accessed.
+ *
+ * When swaping xclbin, first call read_axlf_ioctl to download new xclbin, the
+ * following conditions have to be true:
+ *   -  When we lock the slot_xclbin_lock, no more zocl_ctx/read_axlf
+ *   -  If still have live context, we cannot swap xclbin
+ *   -  If no live contexts, but still live cmds from previous closed context,
+ *      we cannot swap xclbin.
+ * If all the above conditions is cleared, we start changing to new xclbin.
+ */
+int
+zocl_ctx_ioctl(struct drm_device *ddev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = ZOCL_GET_ZDEV(ddev);
+
+	/* Do not acquire slot_xclbin_lock like sched_xclbin_ctx().
+	 * New KDS would lock bitstream when open the fist context.
+	 * The lock bitstream would exclude read_axlf_ioctl().
+	 */
+	return zocl_context_ioctl(zdev, data, filp);
+}
+
+/* IOCTL to get CU index in aperture list
+ * used for recognizing BO and CU in mmap
+ */
+int
+zocl_info_cu_ioctl(struct drm_device *ddev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_info_cu *args = data;
+	struct drm_zocl_dev *zdev = ddev->dev_private;
+	struct addr_aperture *apts = zdev->apertures;
+	int apt_idx = args->apt_idx;
+	int cu_idx = args->cu_idx;
+	phys_addr_t addr = args->paddr;
+
+	if (cu_idx != -1) {
+		apt_idx = get_apt_index_by_cu_idx(zdev, cu_idx);
+		if (apt_idx != -EINVAL) {
+			addr = apts[apt_idx].addr;
+			goto out;
+		}
+	}
+
+	apt_idx = get_apt_index_by_addr(zdev, args->paddr);
+	if (apt_idx != -EINVAL)
+		cu_idx = apts[apt_idx].cu_idx;
+
+out:
+	args->paddr = addr;
+	args->apt_idx = apt_idx;
+	args->cu_idx = cu_idx;
+	return 0;
+}
+
+int
+zocl_execbuf_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = dev->dev_private;
+
+	return zocl_command_ioctl(zdev, data, filp);
+}
+
+int
+zocl_error_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	int ret;
+
+	if (!capable(CAP_SYS_ADMIN))
+		return -EACCES;
+
+	ret = zocl_inject_error(zdev, data, filp);
+	return ret;
+}
+
+int
+zocl_aie_fd_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_aie *args = data;
+	struct drm_zocl_dev *zdev = ZOCL_GET_ZDEV(dev);
+	int ret = 0;
+
+	ret = zocl_aie_request_part_fd(zdev, args);
+	return ret;
+}
+
+int
+zocl_aie_reset_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = ZOCL_GET_ZDEV(dev);
+	int ret;
+
+	ret = zocl_aie_reset(zdev);
+	return ret;
+}
+
+int
+zocl_aie_freqscale_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = ZOCL_GET_ZDEV(dev);
+
+	return zocl_aie_freqscale(zdev, data);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_kds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_kds.c
@@ -0,0 +1,1006 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2020-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Min Ma <min.ma@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/sched/signal.h>
+#include "zocl_drv.h"
+#include "zocl_util.h"
+#include "zocl_xclbin.h"
+#include "kds_core.h"
+#include "xclbin.h"
+
+#define print_ecmd_info(ecmd) \
+do {\
+	int i;\
+	printk("%s: ecmd header 0x%x\n", __func__, ecmd->header);\
+	for (i = 0; i < ecmd->count; i++) {\
+		printk("%s: ecmd data[%d] 0x%x\n", __func__, i, ecmd->data[i]);\
+	}\
+} while(0)
+
+int kds_echo = 0;
+
+/*
+ * Callback function for async dma operation. This will also clean the
+ * command memory.
+ *
+ * @param       arg:	kds command pointer
+ * @param       ret:    return value of the dma operation.
+ *
+ */
+static void zocl_kds_dma_complete(void *arg, int ret)
+{
+	struct kds_command *xcmd = (struct kds_command *)arg;
+	zocl_dma_handle_t *dma_handle = (zocl_dma_handle_t *)xcmd->priv;
+
+	xcmd->status = KDS_COMPLETED;
+	if (ret)
+		xcmd->status = KDS_ERROR;
+	xcmd->cb.notify_host(xcmd, xcmd->status);
+	xcmd->cb.free(xcmd);
+
+	kfree(dma_handle);
+}
+
+/*
+ * Copy the user space command to kds command. Also register the callback
+ * function for the DMA operation.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       flip:	DRM file private data
+ * @param       ecmd:	ERT command structure
+ * @param       xcmd:   KDS command structure
+ *
+ * @return      0 on success, Error code on failure.
+ */
+static int copybo_ecmd2xcmd(struct drm_zocl_dev *zdev, struct drm_file *filp,
+			    struct ert_start_copybo_cmd *ecmd,
+			    struct kds_command *xcmd)
+{
+	struct drm_device *dev = zdev->ddev;
+	zocl_dma_handle_t *dma_handle;
+	struct drm_zocl_copy_bo args = {
+		.dst_handle = ecmd->dst_bo_hdl,
+		.src_handle = ecmd->src_bo_hdl,
+		.size = ert_copybo_size(ecmd),
+		.dst_offset = ert_copybo_dst_offset(ecmd),
+		.src_offset = ert_copybo_src_offset(ecmd),
+	};
+	int ret = 0;
+
+	dma_handle = kmalloc(sizeof(zocl_dma_handle_t), GFP_KERNEL);
+	if (!dma_handle)
+		return -ENOMEM;
+
+	memset(dma_handle, 0, sizeof(zocl_dma_handle_t));
+
+	ret = zocl_dma_channel_instance(dma_handle, zdev);
+	if (ret)
+		return ret;
+
+	/* We must set up callback for async dma operations. */
+	dma_handle->dma_func = zocl_kds_dma_complete;
+	dma_handle->dma_arg = xcmd;
+	xcmd->priv = dma_handle;
+
+	ret = zocl_copy_bo_async(dev, filp, dma_handle, &args);
+	return ret;
+}
+
+static inline void
+zocl_ctx_to_info(struct drm_zocl_ctx *args, struct kds_ctx_info *info)
+{
+	if (args->cu_index == ZOCL_CTX_VIRT_CU_INDEX)
+		info->cu_idx = CU_CTX_VIRT_CU;
+	else
+		info->cu_idx = args->cu_index;
+
+	/* Ignore ZOCL_CTX_SHARED bit if ZOCL_CTX_EXCLUSIVE bit is set */
+	if (args->flags & ZOCL_CTX_EXCLUSIVE)
+		info->flags = CU_CTX_EXCLUSIVE;
+	else
+		info->flags = CU_CTX_SHARED;
+}
+
+/*
+ * Remove the client context and free all the memeory.
+ * This function is also unlock the bitstrean for the slot associated with
+ * this context.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       client:	KDS client structure
+ * @param       cctx:   Client context structure
+ *
+ */
+static void
+zocl_remove_client_context(struct drm_zocl_dev *zdev,
+			struct kds_client *client, struct kds_client_ctx *cctx)
+{
+	struct drm_zocl_slot *slot = NULL;
+	uuid_t *id = (uuid_t *)cctx->xclbin_id;
+
+	/* Check whether active count exists for this context */
+	if (cctx && !cctx->num_ctx) {
+		/* Get the corresponding slot for this xclbin */
+		slot = zocl_get_slot(zdev, id);
+		if (!slot)
+			return;
+
+		/* Unlock this slot specific xclbin */
+		zocl_unlock_bitstream(slot, id);
+
+		list_del(&cctx->link);
+		if (cctx->xclbin_id)
+			vfree(cctx->xclbin_id);
+		if (cctx)
+			vfree(cctx);
+	}
+}
+
+/*
+ * Create a new client context and lock the bitstrean for the slot
+ * associated with this context.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       client:	KDS client structure
+ * @param       id:	XCLBIN id
+ *
+ * @return      newly created context on success, Error code on failure.
+ *
+ */
+static struct kds_client_ctx *
+zocl_create_client_context(struct drm_zocl_dev *zdev,
+			struct kds_client *client, uuid_t *id)
+{
+	struct drm_zocl_slot *slot = NULL;
+	struct kds_client_ctx *cctx = NULL;
+	int ret = 0;
+
+	/* Get the corresponding slot for this xclbin */
+	slot = zocl_get_slot(zdev, id);
+	if (!slot)
+		return NULL;
+
+	/* Lock this slot specific xclbin */
+	ret = zocl_lock_bitstream(slot, id);
+	if (ret)
+		return NULL;
+
+	/* Allocate the new client context and store the xclbin */
+	cctx = vzalloc(sizeof(struct kds_client_ctx));
+	if (!cctx) {
+		(void) zocl_unlock_bitstream(slot, id);
+		return NULL;
+	}
+
+	cctx->xclbin_id = vzalloc(sizeof(uuid_t));
+	if (!cctx->xclbin_id) {
+		vfree(cctx);
+		(void) zocl_unlock_bitstream(slot, id);
+		return NULL;
+	}
+	uuid_copy(cctx->xclbin_id, id);
+
+	list_add_tail(&cctx->link, &client->ctx_list);
+
+	return cctx;
+}
+
+/*
+ * Check whether there is a active context for this xclbin in this kds client.
+ *
+ * @param       client:	KDS client structure
+ * @param       id:	XCLBIN id
+ *
+ * @return      existing context on success, NULL on failure.
+ *
+ */
+static struct kds_client_ctx *
+zocl_check_exists_context(struct kds_client *client, const uuid_t *id)
+{
+	struct kds_client_ctx *curr = NULL;
+
+	/* Find whether the xclbin is already loaded and the context is exists
+	 */
+	list_for_each_entry(curr, &client->ctx_list, link)
+		if (uuid_equal(curr->xclbin_id, id))
+			break;
+
+	/* Not found any matching context */
+	if (&curr->link == &client->ctx_list)
+		return NULL;
+
+	return curr;
+}
+
+/*
+ * Create a new context if no active context present for this xclbin and add
+ * it to the kds.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       client:	KDS client structure
+ * @param       id:	XCLBIN id
+ *
+ * @return      0 on success, error core on failure.
+ *
+ */
+static int
+zocl_add_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		 struct drm_zocl_ctx *args)
+{
+	struct kds_ctx_info info = { 0 };
+	void *uuid_ptr = (void *)(uintptr_t)args->uuid_ptr;
+	struct kds_client_ctx *cctx = NULL;
+	uuid_t *id = NULL;
+	int ret = 0;
+
+	id = vmalloc(sizeof(uuid_t));
+	if (!id)
+		return -ENOMEM;
+
+	ret = copy_from_user(id, uuid_ptr, sizeof(uuid_t));
+	if (ret) {
+		vfree(id);
+		return ret;
+	}
+
+	mutex_lock(&client->lock);
+
+	cctx = zocl_check_exists_context(client, id);
+	if (cctx == NULL) {
+		/* No existing context found. Create a new context to this client */
+		cctx = zocl_create_client_context(zdev, client, id);
+		if (cctx == NULL)
+			goto out;
+	}
+
+	/* Bitstream is locked. No one could load a new one
+	 * until this client close all of the contexts.
+	 */
+	zocl_ctx_to_info(args, &info);
+	info.curr_ctx = (void *)cctx;
+	ret = kds_add_context(&zdev->kds, client, &info);
+	if (ret) {
+		zocl_remove_client_context(zdev, client, cctx);
+		goto out;
+	}
+
+out:
+	mutex_unlock(&client->lock);
+	vfree(id);
+	return ret;
+}
+
+int zocl_add_context_kernel(struct drm_zocl_dev *zdev, void *client_hdl, u32 cu_idx, u32 flags, u32 cu_domain)
+{
+	int ret = 0;
+	struct kds_ctx_info info = { 0 };
+	struct kds_client *client = (struct kds_client *)client_hdl;
+	struct kds_client_ctx *cctx = NULL;
+
+	cctx = vzalloc(sizeof(struct kds_client_ctx));
+	if (!cctx)
+		return -ENOMEM;
+
+	cctx->xclbin_id = vzalloc(sizeof(uuid_t));
+	if (!cctx->xclbin_id) {
+		vfree(info.curr_ctx);
+		return -ENOMEM;
+	}
+	uuid_copy(cctx->xclbin_id, &uuid_null);
+
+	info.cu_domain = cu_domain;
+	info.cu_idx = cu_idx;
+	info.flags = flags;
+	info.curr_ctx = cctx;
+
+	mutex_lock(&client->lock);
+
+	list_add_tail(&(cctx->link), &client->ctx_list);
+	ret = kds_add_context(&zdev->kds, client, &info);
+	mutex_unlock(&client->lock);
+	return ret;
+}
+
+int zocl_del_context_kernel(struct drm_zocl_dev *zdev, void *client_hdl, u32 cu_idx, u32 cu_domain)
+{
+	int ret = 0;
+	struct kds_ctx_info info = { 0 };
+	struct kds_client *client = (struct kds_client *)client_hdl;
+	struct kds_client_ctx *cctx = NULL;
+
+	info.cu_domain = cu_domain;
+	info.cu_idx = cu_idx;
+	mutex_lock(&client->lock);
+	cctx = zocl_check_exists_context(client, &uuid_null);
+	if (cctx == NULL)
+		return -EINVAL;
+
+	info.curr_ctx = (void *)cctx;
+	ret = kds_del_context(&zdev->kds, client, &info);
+
+	list_del(&cctx->link);
+	mutex_unlock(&client->lock);
+
+	if (cctx->xclbin_id)
+		vfree(cctx->xclbin_id);
+	if (cctx)
+		vfree(cctx);
+	return ret;
+}
+
+/*
+ * Detele an existing context and remove it from the kds.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       client:	KDS client structure
+ * @param       args:	userspace arguments
+ *
+ * @return      0 on success, error core on failure.
+ *
+ */
+static int
+zocl_del_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		 struct drm_zocl_ctx *args)
+{
+	struct kds_ctx_info info = { 0 };
+	void *uuid_ptr = (void *)(uintptr_t)args->uuid_ptr;
+	uuid_t *id = NULL;
+	struct kds_client_ctx *cctx = NULL;
+	int ret = 0;
+
+	id = vmalloc(sizeof(uuid_t));
+	if (!id)
+		return -ENOMEM;
+
+	ret = copy_from_user(id, uuid_ptr, sizeof(uuid_t));
+	if (ret) {
+		vfree(id);
+		return ret;
+	}
+
+	mutex_lock(&client->lock);
+	cctx = zocl_check_exists_context(client, id);
+	if (cctx == NULL) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	zocl_ctx_to_info(args, &info);
+
+	/* Store the current context here. KDS required that later */
+	info.curr_ctx = (void *)cctx;
+	ret = kds_del_context(&zdev->kds, client, &info);
+	if (ret)
+		goto out;
+
+	/* Delete the current client context */
+	zocl_remove_client_context(zdev, client, cctx);
+
+out:
+	mutex_unlock(&client->lock);
+	vfree(id);
+	return ret;
+}
+
+static int
+zocl_add_graph_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		struct drm_zocl_ctx *args)
+{
+	void *uuid_ptr = (void *)(uintptr_t)args->uuid_ptr;
+	xuid_t *xclbin_id = NULL;
+	uuid_t *ctx_id = NULL;
+	u32 gid = args->graph_id;
+	u32 flags = args->flags;
+	int ret = 0;
+	struct drm_zocl_slot *slot = NULL;
+
+	ctx_id = vmalloc(sizeof(uuid_t));
+	if (!ctx_id)
+		return -ENOMEM;
+
+	ret = copy_from_user(ctx_id, uuid_ptr, sizeof(uuid_t));
+	if (ret)
+		goto out;
+
+	/* Get the corresponding slot for this xclbin
+	 */
+	slot = zocl_get_slot(zdev, ctx_id);
+	if (!slot)
+		return -EINVAL;
+
+	mutex_lock(&slot->slot_xclbin_lock);
+	xclbin_id = (xuid_t *)zocl_xclbin_get_uuid(slot);
+	mutex_unlock(&slot->slot_xclbin_lock);
+
+	mutex_lock(&client->lock);
+	if (!uuid_equal(ctx_id, xclbin_id)) {
+		DRM_ERROR("try to allocate Graph CTX with wrong xclbin %pUB",
+		    ctx_id);
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = zocl_aie_kds_add_graph_context(zdev, gid, flags, client);
+out:
+	mutex_unlock(&client->lock);
+	vfree(ctx_id);
+	return ret;
+}
+
+static int
+zocl_del_graph_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		struct drm_zocl_ctx *args)
+{
+	u32 gid = args->graph_id;
+	int ret = 0;
+
+	mutex_lock(&client->lock);
+	ret = zocl_aie_kds_del_graph_context(zdev, gid, client);
+	mutex_unlock(&client->lock);
+
+	return 0;
+}
+
+static int
+zocl_add_aie_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		struct drm_zocl_ctx *args)
+{
+	u32 flags = args->flags;
+
+	return zocl_aie_kds_add_context(zdev, flags, client);
+}
+
+static int
+zocl_del_aie_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		struct drm_zocl_ctx *args)
+{
+	return zocl_aie_kds_del_context(zdev, client);
+}
+
+static int
+zocl_open_ucu(struct drm_zocl_dev *zdev, struct kds_client *client,
+	      struct drm_zocl_ctx *args)
+{
+	struct kds_sched  *kds = NULL;
+	u32 cu_idx = args->cu_index;
+
+	kds = &zdev->kds;
+	return kds_open_ucu(kds, client, cu_idx);
+}
+
+/*
+ * This is an entry point for context ioctl. This function calls the
+ * appropoate function based on the requested operation from the userspace.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       data:	userspace arguments
+ * @param       flip:	DRM file private data
+ *
+ * @return      0 on success, error core on failure.
+ *
+ */
+int zocl_context_ioctl(struct drm_zocl_dev *zdev, void *data,
+		       struct drm_file *filp)
+{
+	struct drm_zocl_ctx *args = data;
+	struct kds_client *client = filp->driver_priv;
+	int ret = 0;
+
+	switch (args->op) {
+	case ZOCL_CTX_OP_ALLOC_CTX:
+		ret = zocl_add_context(zdev, client, args);
+		break;
+	case ZOCL_CTX_OP_FREE_CTX:
+		ret = zocl_del_context(zdev, client, args);
+		break;
+	case ZOCL_CTX_OP_ALLOC_GRAPH_CTX:
+		ret = zocl_add_graph_context(zdev, client, args);
+		break;
+	case ZOCL_CTX_OP_FREE_GRAPH_CTX:
+		ret = zocl_del_graph_context(zdev, client, args);
+		break;
+	case ZOCL_CTX_OP_ALLOC_AIE_CTX:
+		ret = zocl_add_aie_context(zdev, client, args);
+		break;
+	case ZOCL_CTX_OP_FREE_AIE_CTX:
+		ret = zocl_del_aie_context(zdev, client, args);
+		break;
+	case ZOCL_CTX_OP_OPEN_GCU_FD:
+		ret = zocl_open_ucu(zdev, client, args);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+static void notify_execbuf(struct kds_command *xcmd, int status)
+{
+	struct kds_client *client = xcmd->client;
+	struct ert_packet *ecmd = (struct ert_packet *)xcmd->execbuf;
+
+	if (status == KDS_COMPLETED)
+		ecmd->state = ERT_CMD_STATE_COMPLETED;
+	else if (status == KDS_ERROR)
+		ecmd->state = ERT_CMD_STATE_ERROR;
+	else if (status == KDS_TIMEOUT)
+		ecmd->state = ERT_CMD_STATE_TIMEOUT;
+	else if (status == KDS_ABORT)
+		ecmd->state = ERT_CMD_STATE_ABORT;
+
+	if (xcmd->timestamp_enabled) {
+		/* Only start kernel command supports timestamps */
+		struct ert_start_kernel_cmd *scmd;
+		struct cu_cmd_state_timestamps *ts;
+
+		scmd = (struct ert_start_kernel_cmd *)ecmd;
+		ts = ert_start_kernel_timestamps(scmd);
+		ts->skc_timestamps[ERT_CMD_STATE_NEW] = xcmd->timestamp[KDS_NEW];
+		ts->skc_timestamps[ERT_CMD_STATE_QUEUED] = xcmd->timestamp[KDS_QUEUED];
+		ts->skc_timestamps[ERT_CMD_STATE_RUNNING] = xcmd->timestamp[KDS_RUNNING];
+		ts->skc_timestamps[ecmd->state] = xcmd->timestamp[status];
+	}
+
+	ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(xcmd->gem_obj);
+
+	if (xcmd->cu_idx >= 0)
+		client_stat_inc(client, c_cnt[xcmd->cu_idx]);
+
+	atomic_inc(&client->event);
+	wake_up_interruptible(&client->waitq);
+}
+
+/* This function returns the corresponding context associated to the given CU
+ *
+ * @param	zdev:   zocl device structure
+ * @param       client:	KDS client context
+ * @param       cu_idx:	CU index
+ *
+ * @return      context on success, error core on failure.
+ */
+static struct kds_client_ctx *
+zocl_get_cu_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		    int cu_idx)
+{
+	struct kds_sched *kds = &zdev->kds;
+	struct drm_zocl_slot *slot = NULL;
+	struct kds_cu_mgmt *cu_mgmt = NULL;
+	u32 slot_idx = 0xFFFF;
+
+	if (!kds)
+		return NULL;
+
+	cu_mgmt = &kds->cu_mgmt;
+	if (cu_mgmt) {
+		struct xrt_cu *xcu = cu_mgmt->xcus[cu_idx];
+
+		/* Found the cu Index. Extract slot id out of it */
+		if (xcu)
+			slot_idx = xcu->info.slot_idx;
+	}
+
+	slot = zdev->pr_slot[slot_idx];
+	if (slot) {
+		struct kds_client_ctx *curr;
+		mutex_lock(&slot->slot_xclbin_lock);
+		list_for_each_entry(curr, &client->ctx_list, link) {
+			if (uuid_equal(curr->xclbin_id,
+				       zocl_xclbin_get_uuid(slot))) {
+				curr->slot_idx = slot->slot_idx;
+				break;
+			}
+		}
+		mutex_unlock(&slot->slot_xclbin_lock);
+
+		/* check matching context */
+		if (&curr->link != &client->ctx_list) {
+			/* Found one context */
+			return curr;
+		}
+	}
+
+	/* No match found. Invalid Context */
+	return NULL;
+
+}
+
+/* Every CU is associated with a slot. And a client can open only one
+ * context for a slot. Hence, from the CU we can validate whethe the
+ * current context is valid or not.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       client:	KDS client context
+ * @param       xcmd:	KDS command structure
+ *
+ * @return      0 on success, error core on failure.
+ */
+static int
+check_for_open_context(struct drm_zocl_dev *zdev, struct kds_client *client,
+		      struct kds_command *xcmd)
+{
+	int first_cu_idx = -EINVAL;
+	u32 mask = 0;
+	int i, j;
+
+	/* i for iterate masks, j for iterate bits */
+	for (i = 0; i < xcmd->num_mask; ++i) {
+		if (xcmd->cu_mask[i] == 0)
+			continue;
+
+		mask = xcmd->cu_mask[i];
+		for (j = 0; mask > 0; ++j) {
+			if (!(mask & 0x1)) {
+				mask >>= 1;
+				continue;
+			}
+
+			first_cu_idx = i * sizeof(u32) + j;
+			goto out;
+		}
+	}
+
+out:
+	if (first_cu_idx < 0)
+		return -EINVAL;
+
+	if (zocl_get_cu_context(zdev, client, first_cu_idx) != NULL)
+		return 0;
+	else
+		return -EINVAL;
+}
+
+/*
+ * This function will create a kds command using the given parameters from the
+ * userspace and add that to the KDS.
+ *
+ * @param	zdev:   zocl device structure
+ * @param       data:	userspace arguments
+ * @param       flip:	DRM file private data
+ *
+ * @return      0 on success, error core on failure.
+ */
+int zocl_command_ioctl(struct drm_zocl_dev *zdev, void *data,
+		       struct drm_file *filp)
+{
+	struct drm_gem_object *gem_obj = NULL;
+	struct drm_device *dev = zdev->ddev;
+	struct drm_zocl_execbuf *args = data;
+	struct kds_client *client = filp->driver_priv;
+	struct drm_zocl_bo *zocl_bo = NULL;
+	struct ert_packet *ecmd = NULL;
+	struct kds_command *xcmd = NULL;
+	int ret = 0;
+
+	if (zdev->kds.bad_state) {
+		DRM_ERROR("KDS is in bad state\n");
+		return -EDEADLK;
+	}
+
+	gem_obj = zocl_gem_object_lookup(dev, filp, args->exec_bo_handle);
+	if (!gem_obj) {
+		DRM_ERROR("Look up GEM BO %d failed\n", args->exec_bo_handle);
+		return -EINVAL;
+	}
+
+	zocl_bo = to_zocl_bo(gem_obj);
+	if (!zocl_bo_execbuf(zocl_bo)) {
+		DRM_ERROR("Command buffer is not exec buf\n");
+		return -EINVAL;
+	}
+
+	ecmd = (struct ert_packet *)zocl_bo->cma_base.vaddr;
+
+	ecmd->state = ERT_CMD_STATE_NEW;
+	/* only the user command knows the real size of the payload.
+	 * count is more than enough!
+	 */
+	xcmd = kds_alloc_command(client, ecmd->count * sizeof(u32));
+	if (!xcmd) {
+		DRM_ERROR("Failed to alloc xcmd\n");
+		ret = -ENOMEM;
+		goto out;
+	}
+	xcmd->cb.free = kds_free_command;
+	xcmd->cb.notify_host = notify_execbuf;
+	xcmd->execbuf = (u32 *)ecmd;
+	xcmd->gem_obj = gem_obj;
+	xcmd->exec_bo_handle = args->exec_bo_handle;
+
+	//print_ecmd_info(ecmd);
+
+	switch(ecmd->opcode) {
+	case ERT_CONFIGURE:
+		xcmd->status = KDS_COMPLETED;
+		xcmd->cb.notify_host(xcmd, xcmd->status);
+		goto out1;
+	case ERT_START_CU:
+		start_krnl_ecmd2xcmd(to_start_krnl_pkg(ecmd), xcmd);
+		break;
+	case ERT_EXEC_WRITE:
+		DRM_WARN_ONCE("ERT_EXEC_WRITE is obsoleted, use ERT_START_KEY_VAL\n");
+#if KERNEL_VERSION(5, 4, 0) > LINUX_VERSION_CODE
+		__attribute__ ((fallthrough));
+#else
+		__attribute__ ((__fallthrough__));
+#endif
+		/* pass through */
+	case ERT_START_KEY_VAL:
+		start_krnl_kv_ecmd2xcmd(to_start_krnl_pkg(ecmd), xcmd);
+		break;
+	case ERT_START_FA:
+		start_fa_ecmd2xcmd(to_start_krnl_pkg(ecmd), xcmd);
+		break;
+	case ERT_START_COPYBO:
+		ret = copybo_ecmd2xcmd(zdev, filp, to_copybo_pkg(ecmd), xcmd);
+		if (ret)
+			goto out1;
+		goto out;
+	case ERT_ABORT:
+		abort_ecmd2xcmd(to_abort_pkg(ecmd), xcmd);
+		break;
+	default:
+		DRM_ERROR("Unsupport command\n");
+		ret = -EINVAL;
+		goto out1;
+	}
+
+	/* Check whether client has already Open Context for this Command */
+	if (check_for_open_context(zdev, client, xcmd) < 0) {
+		DRM_ERROR("The client has no opening context\n");
+		return -EINVAL;
+	}
+
+	/* Now, we could forget execbuf */
+	ret = kds_add_command(&zdev->kds, xcmd);
+	return ret;
+
+out1:
+	xcmd->cb.free(xcmd);
+out:
+	/* Don't forget to put gem object if error happen */
+	if (ret < 0) {
+		ZOCL_DRM_GEM_OBJECT_PUT_UNLOCKED(gem_obj);
+	}
+	return ret;
+}
+
+uint zocl_poll_client(struct file *filp, poll_table *wait)
+{
+	struct drm_file *priv = filp->private_data;
+	struct kds_client *client = (struct kds_client *)priv->driver_priv;
+	int event = 0;
+
+	poll_wait(filp, &client->waitq, wait);
+
+	event = atomic_dec_if_positive(&client->event);
+	if (event == -1)
+		return 0;
+
+	return POLLIN;
+}
+
+/*
+ * Create a new client and initialize it with KDS.
+ *
+ * @param	zdev:		zocl device structure
+ * @param       priv[output]:	new client pointer
+ *
+ * @return      0 on success, error core on failure.
+ */
+int zocl_create_client(struct device *dev, void **client_hdl)
+{
+	struct drm_zocl_dev *zdev = zocl_get_zdev();
+	struct kds_client *client = NULL;
+	struct kds_sched  *kds = NULL;
+	int ret = 0;
+
+	client = kzalloc(sizeof(*client), GFP_KERNEL);
+	if (!client)
+		return -ENOMEM;
+
+	kds = &zdev->kds;
+	client->dev = dev;
+	ret = kds_init_client(kds, client);
+	if (ret) {
+		kfree(client);
+		goto out;
+	}
+
+	/* Multiple context can be active. Initializing context list */
+	INIT_LIST_HEAD(&client->ctx_list);
+
+	INIT_LIST_HEAD(&client->graph_list);
+	spin_lock_init(&client->graph_list_lock);
+	*client_hdl = client;
+
+out:
+	zocl_info(dev, "created KDS client for pid(%d), ret: %d\n",
+		  pid_nr(task_tgid(current)), ret);
+	return ret;
+}
+
+/*
+ * Destroy the given client and delete it from the KDS.
+ *
+ * @param	zdev:	zocl device structure
+ * @param       priv:	client pointer
+ *
+ */
+void zocl_destroy_client(void *client_hdl)
+{
+	struct drm_zocl_dev *zdev = zocl_get_zdev();
+	struct kds_client *client = (struct kds_client *)client_hdl;
+	struct kds_sched  *kds = NULL;
+	struct kds_client_ctx *curr = NULL;
+	struct kds_client_ctx *tmp = NULL;
+	struct drm_zocl_slot *slot = NULL;
+	int pid = pid_nr(client->pid);
+
+	if (!zdev) {
+		zocl_info(client->dev, "client exits pid(%d)\n", pid);
+		kfree(client);
+		return;
+	}
+
+	kds = &zdev->kds;
+
+	/* kds_fini_client should released resources hold by the client.
+	 * release xclbin_id and unlock bitstream if needed.
+	 */
+	zocl_aie_kds_del_graph_context_all(client);
+	kds_fini_client(kds, client);
+
+	/* Delete all the existing context associated to this device for this
+	 * client.
+	 */
+	list_for_each_entry_safe(curr, tmp, &client->ctx_list, link) {
+		/* Get the corresponding slot for this xclbin */
+		slot = zocl_get_slot(zdev, curr->xclbin_id);
+		if (!slot)
+			continue;
+
+		/* Unlock this slot specific xclbin */
+		zocl_unlock_bitstream(slot, curr->xclbin_id);
+		vfree(curr->xclbin_id);
+		list_del(&curr->link);
+		vfree(curr);
+	}
+
+	zocl_info(client->dev, "client exits pid(%d)\n", pid);
+	kfree(client);
+}
+
+int zocl_init_sched(struct drm_zocl_dev *zdev)
+{
+	return kds_init_sched(&zdev->kds);
+}
+
+void zocl_fini_sched(struct drm_zocl_dev *zdev)
+{
+	struct drm_zocl_bo *bo = NULL;
+
+	bo = zdev->kds.cmdmem.bo;
+	if (bo)
+		zocl_drm_free_bo(bo);
+	zdev->kds.cmdmem.bo = NULL;
+
+	kds_fini_sched(&zdev->kds);
+}
+
+static void zocl_detect_fa_cmdmem(struct drm_zocl_dev *zdev,
+				  struct drm_zocl_slot *slot)
+{
+	struct ip_layout    *ip_layout = NULL;
+	struct drm_zocl_bo *bo = NULL;
+	struct drm_zocl_create_bo args = { 0 };
+	int i = 0;
+	uint64_t size = 0;
+	uint64_t base_addr = 0;
+	void __iomem *vaddr = NULL;
+	ulong bar_paddr = 0;
+
+	/* Detect Fast adapter */
+	ip_layout = slot->ip;
+	if (!ip_layout)
+		return;
+
+	for (i = 0; i < ip_layout->m_count; ++i) {
+		struct ip_data *ip = &ip_layout->m_ip_data[i];
+		u32 prot;
+
+		if (ip->m_type != IP_KERNEL)
+			continue;
+
+		prot = (ip->properties & IP_CONTROL_MASK) >> IP_CONTROL_SHIFT;
+		if (prot != FAST_ADAPTER)
+			continue;
+
+		break;
+	}
+
+	if (i == ip_layout->m_count)
+		return;
+
+	/* TODO: logic to dynamicly select size */
+	size = 4096;
+
+	args.size = size;
+	args.flags = ZOCL_BO_FLAGS_CMA;
+	bo = zocl_drm_create_bo(zdev->ddev, size, args.flags);
+	if (IS_ERR(bo))
+		return;
+
+	
+	bar_paddr = (uint64_t)bo->cma_base.paddr;	
+	base_addr = (uint64_t)bo->cma_base.paddr;	
+	vaddr = bo->cma_base.vaddr;	
+
+	zdev->kds.cmdmem.bo = bo;
+	zdev->kds.cmdmem.bar_paddr = bar_paddr;
+	zdev->kds.cmdmem.dev_paddr = base_addr;
+	zdev->kds.cmdmem.vaddr = vaddr;
+	zdev->kds.cmdmem.size = size;
+}
+
+int zocl_kds_update(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot,
+		    struct drm_zocl_kds *cfg)
+{
+	struct drm_zocl_bo *bo = NULL;
+	int i;
+
+	if (zdev->kds.cmdmem.bo) {
+		bo = zdev->kds.cmdmem.bo;
+		zocl_drm_free_bo(bo);
+		zdev->kds.cmdmem.bo = NULL;
+		zdev->kds.cmdmem.bar_paddr = 0;
+		zdev->kds.cmdmem.dev_paddr = 0;
+		zdev->kds.cmdmem.vaddr = 0;
+		zdev->kds.cmdmem.size = 0;
+	}
+
+	zocl_detect_fa_cmdmem(zdev, slot);
+	
+	// Default supporting interrupt mode
+	zdev->kds.cu_intr_cap = 1;	
+
+	for (i = 0; i < MAX_CUS; i++) {
+		struct xrt_cu *xcu;
+		int apt_idx;
+
+		xcu = zdev->kds.cu_mgmt.xcus[i];
+		if (!xcu)
+			continue;
+
+		apt_idx = get_apt_index_by_addr(zdev, xcu->info.addr); 
+		if (apt_idx < 0) {
+			DRM_ERROR("CU address %llx is not found in XCLBIN\n",
+			    xcu->info.addr);
+			return apt_idx;
+		}
+		update_cu_idx_in_apt(zdev, apt_idx, i);
+	}
+
+	// Check for polling mode and enable CU interrupt if polling_mode is false
+	if (cfg->polling)
+		zdev->kds.cu_intr = 0;
+	else
+		zdev->kds.cu_intr = 1;
+
+	return kds_cfg_update(&zdev->kds);
+}
+
+int zocl_kds_reset(struct drm_zocl_dev *zdev)
+{
+	kds_reset(&zdev->kds);
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_lib.c
@@ -0,0 +1,142 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include "zocl_lib.h"
+
+void __iomem *zlib_map_res(struct device *dev, struct resource *res, u64 *startp, size_t *szp)
+{
+	void __iomem *map = devm_ioremap(dev, res->start, res->end - res->start + 1);
+
+	if (IS_ERR(map)) {
+		zocl_err(dev, "Failed to map resource: %ld", PTR_ERR(map));
+		return NULL;
+	}
+
+	if (startp)
+		*startp = res->start;
+	if (szp)
+		*szp = res->end - res->start + 1;
+	return map;
+}
+
+void __iomem *zlib_map_res_by_id(struct platform_device *pdev, int id, u64 *startp, size_t *szp)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, id);
+
+	if (!res) {
+		zocl_err(dev, "failed to find resource ID (%d)", id);
+		return NULL;
+	}
+	zocl_info(dev, "Found resource (%d): %pR", id, res);
+
+	return zlib_map_res(dev, res, startp, szp);
+}
+
+void __iomem *zlib_map_res_by_name(struct platform_device *pdev,
+				   const char *name, u64 *startp, size_t *szp)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res = platform_get_resource_byname(pdev, IORESOURCE_MEM, name);
+
+	if (!res) {
+		zocl_err(dev, "failed to find resource (%s)", name);
+		return NULL;
+	}
+	zocl_info(dev, "Found resource (%s): %pR", name, res);
+
+	return zlib_map_res(dev, res, startp, szp);
+}
+
+void __iomem *zlib_map_phandle_res_by_name(struct platform_device *pdev,
+					   const char *name, u64 *startp, size_t *szp)
+{
+	int ret = -EINVAL;
+	struct resource res = {};
+	struct device_node *np = NULL;
+	struct device *dev = &pdev->dev;
+
+	np = of_parse_phandle(dev->of_node, name, 0);
+	if (np)
+		ret = of_address_to_resource(np, 0, &res);
+	if (ret) {
+		zocl_err(dev, "failed to find resource (%s): %d", name, ret);
+		return NULL;
+	}
+	zocl_info(dev, "Found resource (%s): %pR", name, &res);
+
+	return zlib_map_res(dev, &res, startp, szp);
+}
+
+int zlib_create_subdev(struct device *dev, const char *devname, struct resource *res, size_t nres,
+		       void *info, size_t info_size, struct platform_device **pdevp)
+{
+	struct platform_device *pldev;
+	int ret;
+
+	pldev = platform_device_alloc(devname, PLATFORM_DEVID_AUTO);
+	if (!pldev) {
+		zocl_err(dev, "Failed to alloc %s device", devname);
+		return -ENOMEM;
+	}
+
+	ret = platform_device_add_resources(pldev, res, nres);
+	if (ret) {
+		zocl_err(dev, "Failed to add resource for %s device", devname);
+		goto err;
+	}
+
+	if (info) {
+		ret = platform_device_add_data(pldev, info, info_size);
+		if (ret) {
+			zocl_err(dev, "Failed to add data for %s device", devname);
+			goto err;
+		}
+	}
+
+	pldev->dev.parent = dev;
+
+	ret = platform_device_add(pldev);
+	if (ret) {
+		zocl_err(dev, "Failed to create %s device", devname);
+		goto err;
+	}
+
+	ret = device_attach(&pldev->dev);
+	if (ret != 1) {
+		ret = -EINVAL;
+		zocl_err(dev, "Failed to attach driver to %s device", devname);
+		goto err1;
+	}
+
+	*pdevp = pldev;
+
+	return 0;
+
+err1:
+	platform_device_del(pldev);
+err:
+	platform_device_put(pldev);
+	return ret;
+}
+
+void zlib_destroy_subdev(struct platform_device *pdev)
+{
+	if (!pdev)
+		return;
+
+	platform_device_del(pdev);
+	platform_device_put(pdev);
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_mailbox.c
@@ -0,0 +1,70 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu       <yliu@xilinx.com>
+ *    David Zhang     <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "ert.h"
+#include "zocl_drv.h"
+#include "zocl_mailbox.h"
+
+static inline const char *
+reg2name(struct mailbox *mbx, u32 *reg)
+{
+	const char *reg_names[] = {
+		"wrdata",
+		"reserved1",
+		"rddata",
+		"reserved2",
+		"status",
+		"error",
+		"sit",
+		"rit",
+		"is",
+		"ie",
+		"ip",
+		"ctrl"
+	};
+
+	return reg_names[((uintptr_t)reg -
+		(uintptr_t)mbx->mbx_regs) / sizeof(u32)];
+}
+
+static inline u32
+mailbox_reg_read(u32 *reg)
+{
+	return ioread32(reg);
+}
+
+static inline void
+mailbox_reg_write(u32 *reg, u32 val)
+{
+	iowrite32(val, reg);
+}
+
+u32
+zocl_mailbox_status(struct mailbox *mbx)
+{
+	return mailbox_reg_read(&mbx->mbx_regs->mbr_status);
+}
+
+u32
+zocl_mailbox_get(struct mailbox *mbx)
+{
+	return mailbox_reg_read(&mbx->mbx_regs->mbr_rddata);
+}
+
+void
+zocl_mailbox_set(struct mailbox *mbx, u32 val)
+{
+	mailbox_reg_write(&mbx->mbx_regs->mbr_wrdata, val);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_ospi_versal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_ospi_versal.c
@@ -0,0 +1,521 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu <yliu@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/delay.h>
+#include <linux/kthread.h>
+#include <linux/platform_device.h>
+
+#include "zocl_drv.h"
+#include "xrt_drv.h"
+#include "sched_exec.h"
+#include "zocl_xclbin.h"
+#include "zocl_ospi_versal.h"
+
+#define ov_err(pdev, fmt, args...)  \
+	zocl_err(&pdev->dev, fmt"\n", ##args)
+#define ov_info(pdev, fmt, args...)  \
+	zocl_info(&pdev->dev, fmt"\n", ##args)
+#define ov_dbg(pdev, fmt, args...)  \
+	zocl_dbg(&pdev->dev, fmt"\n", ##args)
+
+static inline u32 wait_for_status(struct zocl_ov_dev *ov, u8 status)
+{
+	u32 header;
+	struct pdi_packet *pkt = (struct pdi_packet *)&header;
+
+	for (;;) {
+		header = ioread32(ov->base);
+		if (pkt->pkt_status == status)
+			break;
+	}
+
+	return header;
+}
+
+static inline u8 get_pkt_flags(struct zocl_ov_dev *ov)
+{
+	struct pdi_packet *pkt;
+	u32 header;
+
+	pkt = (struct pdi_packet *)&header;
+	header = ioread32(ov->base);
+	return pkt->pkt_flags;
+}
+
+static inline bool check_for_status(struct zocl_ov_dev *ov, u8 status)
+{
+	struct pdi_packet *pkt;
+	u32 header;
+
+	pkt = (struct pdi_packet *)&header;
+	header = ioread32(ov->base);
+	return (pkt->pkt_status == status);
+}
+
+static inline void set_flags(struct zocl_ov_dev *ov, u8 flags)
+{
+	struct pdi_packet *pkt;
+	u32 header;
+
+	pkt = (struct pdi_packet *)&header;
+	header = ioread32(ov->base);
+	pkt->pkt_flags = flags;
+
+	iowrite32(pkt->header, ov->base);
+}
+
+static inline void set_version(struct zocl_ov_dev *ov)
+{
+	set_flags(ov, XRT_XFR_VER <<  XRT_XFR_PKT_VER_SHIFT);
+}
+
+static inline void set_status(struct zocl_ov_dev *ov, u8 status)
+{
+	struct pdi_packet *pkt;
+	u32 header;
+
+	pkt = (struct pdi_packet *)&header;
+	header = ioread32(ov->base);
+	pkt->pkt_status = status;
+
+	iowrite32(pkt->header, ov->base);
+}
+
+static inline void read_data(u32 *addr, u32 *data, size_t sz)
+{
+	int i;
+
+	for (i = 0; i < sz; ++i)
+		*(data + i) = ioread32(addr + i);
+}
+
+static void zocl_ov_clean(struct zocl_ov_dev *ov)
+{
+	struct zocl_ov_pkt_node *node;
+	struct zocl_ov_pkt_node *pnode;
+
+	node = ov->head;
+	while (node != NULL) {
+		pnode = node;
+		node = pnode->zn_next;
+		vfree(pnode->zn_datap);
+		vfree(pnode);
+	}
+
+	ov->head = NULL;
+}
+
+static int zocl_ov_find_parent_dev(struct zocl_ov_dev *ov)
+{
+	struct platform_device *parent_dev;
+
+	parent_dev = zocl_find_pdev("zyxclmm_drm");
+	if (parent_dev) {
+		ov_info(ov->pdev, "Found parent pdev zyxclmm_drv: 0x%llx",
+		    (uint64_t)(uintptr_t)parent_dev);
+		ov->ppdev = parent_dev;
+		return 0;
+	}
+
+	ov_err(ov->pdev, "Can NOT find parent pdev zyxclmm_drv");
+
+	ov->ppdev = NULL;
+	return -ENXIO;
+}
+
+static int zocl_ov_copy_xclbin(struct zocl_ov_dev *ov, struct axlf **xclbin)
+{
+	struct zocl_ov_pkt_node *node = ov->head;
+	char *xp;
+	size_t len = 0;
+
+	while (node) {
+		len += node->zn_size;
+		node = node->zn_next;
+	}
+
+	if (len == 0) {
+		ov_err(ov->pdev, "Load xclbin failed: size is 0");
+		return -EINVAL;
+	}
+
+	*xclbin = vmalloc(len);
+	if (!(*xclbin)) {
+		ov_err(ov->pdev, "Load xclbin failed to allocate buf");
+		return -ENOMEM;
+	}
+
+	xp = (char *)*xclbin;
+	node = ov->head;
+	while (node) {
+		memcpy(xp, node->zn_datap, node->zn_size);
+		xp += node->zn_size;
+		node = node->zn_next;
+	}
+
+	return 0;
+}
+
+static int zocl_ov_recieve(struct zocl_ov_dev *ov)
+{
+	struct zocl_ov_pkt_node *node = ov->head;
+	u32 *base = ov->base;
+	int len = 0, next = 0;
+	int ret;
+
+	for (;;) {
+		u32 pkt_header;
+		struct pdi_packet *pkt = (struct pdi_packet *)&pkt_header;
+		struct zocl_ov_pkt_node *new;
+
+		/* Busy wait here until we get a new packet */
+		pkt_header = wait_for_status(ov, XRT_XFR_PKT_STATUS_NEW);
+
+		new = vzalloc(sizeof(struct zocl_ov_pkt_node));
+		if (!new) {
+			ret = -ENOMEM;
+			break;
+		}
+		new->zn_datap = vmalloc(ov->size);
+		if (!new->zn_datap) {
+			ret = -ENOMEM;
+			break;
+		}
+		new->zn_size = pkt->pkt_size;
+
+		/* Read packet data payload on a 4 bytes base */
+		read_data(base + (sizeof(struct pdi_packet)) / 4,
+		    new->zn_datap, (ov->size - sizeof(struct pdi_packet)) / 4);
+
+		/* Notify host that the data has been read */
+		set_status(ov, XRT_XFR_PKT_STATUS_IDLE);
+
+		len += ov->size;
+		if ((len / 1000000) > next) {
+			ov_info(ov->pdev, "%d M", len / 1000000);
+			next++;
+		}
+
+		/* Add packet data to linked list */
+		if (node)
+			node->zn_next = new;
+		else
+			ov->head = new;
+		node = new;
+
+		/* Bail out here if this is the last packet */
+		if (pkt->pkt_flags & XRT_XFR_PKT_FLAGS_LAST) {
+			ret = 0;
+			break;
+		}
+	}
+
+	return ret;
+}
+
+/*
+ * This function is called once we detect there is a new XCLBIN packet and it
+ * will communicate with host driver to collect all XCLBIN packets and then
+ * call zocl driver service to load this xclbin.
+ *
+ * 1) start receiving XCLBIN packets
+ * 2) put all XCLBIN packets into a linked packets list
+ * 3) once got all packets, copy XCLBIN packets to a XCLBIN buffer
+ * 4) call zocl driver service to load XCLBIN
+ * 5) update XCLBIN packet status to notify host
+ */
+static int zocl_ov_get_xclbin(struct zocl_ov_dev *ov)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *slot = NULL;
+	struct axlf *xclbin = NULL;
+	void *pdrv = NULL;
+	int ret = 0;
+
+	ov_info(ov->pdev, "xclbin is being downloaded...");
+
+	write_lock(&ov->att_rwlock);
+
+	ret = zocl_ov_recieve(ov);
+	if (ret) {
+		set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+		ov_err(ov->pdev, "Fail to recieve XCLBIN file %d", ret);
+		goto out;
+	}
+
+	ov_info(ov->pdev, "XCLBIN is transfered");
+
+	ret = zocl_ov_copy_xclbin(ov, &xclbin);
+	if (ret) {
+		set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+		goto out;
+	}
+
+	if (!ov->ppdev) {
+		ret = zocl_ov_find_parent_dev(ov);
+		if (ret) {
+			set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+			goto out;
+		}
+	}
+
+	pdrv = platform_get_drvdata(ov->ppdev);
+	if (!pdrv) {
+		ov_err(ov->pdev, "Fail to get parent dev driver data");
+		set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+		ret = -ENXIO;
+		goto out;
+	}
+
+	write_unlock(&ov->att_rwlock);
+	zdev = (struct drm_zocl_dev *)pdrv;
+	if (!zdev) {
+		ret = -ENXIO;
+		goto out;
+	}
+
+	/* For OSPI device use default slot i.e. 0 */
+	slot = zdev->pr_slot[0];
+	ret = zocl_xclbin_load_pdi(pdrv, xclbin, slot);
+	if (ret) {
+		set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+		goto out;
+	}
+	write_lock(&ov->att_rwlock);
+
+	ov_info(ov->pdev, "xclbin_done: %d", ov->pdi_done);
+
+	set_status(ov, XRT_XFR_PKT_STATUS_DONE);
+
+out:
+	zocl_ov_clean(ov);
+	write_unlock(&ov->att_rwlock);
+	vfree(xclbin);
+
+	wait_for_status(ov, XRT_XFR_PKT_STATUS_IDLE);
+	set_version(ov);
+
+	return ret;
+}
+
+/*
+ * This function is called once we detect there is a new PDI packet and it
+ * will communicate with host driver to collect all PDI packets and then
+ * communicate with user space daemon to flash the PDI.
+ *
+ * 1) start receiving PDI packets
+ * 2) put all pdi packets into a linked packets list
+ * 3) once got all packets, update sysfs node to indicate PDI is ready
+ * 4) wait on sysfs node on PDI flash done
+ * 5) update PDI packet status to notify host
+ */
+static int zocl_ov_get_pdi(struct zocl_ov_dev *ov)
+{
+	int ret;
+
+	ov_info(ov->pdev, "pdi is being downloaded...");
+
+	/* Clear the done flag */
+	write_lock(&ov->att_rwlock);
+	ov->pdi_done = 0;
+
+	ret = zocl_ov_recieve(ov);
+	if (ret) {
+		write_unlock(&ov->att_rwlock);
+		set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+		ov_err(ov->pdev, "Fail to recieve PDI file %d", ret);
+		goto fail;
+	}
+
+	ov_info(ov->pdev, "pdi is ready for ospi_daemon");
+
+	/* Set ready flag */
+	ov->pdi_ready = 1;
+	write_unlock(&ov->att_rwlock);
+
+	/* Wait for done */
+	read_lock(&ov->att_rwlock);
+	while (true) {
+		/*
+		 * pdi_done indicates the status of the flashing
+		 * 0: in progress
+		 * 1: completed successfully
+		 * 2: fail
+		 */
+		if (!ov->pdi_done) {
+			read_unlock(&ov->att_rwlock);
+			msleep(ZOCL_OV_TIMER_INTERVAL);
+			read_lock(&ov->att_rwlock);
+			continue;
+		}
+		if (ov->pdi_done == 1)
+			set_status(ov, XRT_XFR_PKT_STATUS_DONE);
+		else
+			set_status(ov, XRT_XFR_PKT_STATUS_FAIL);
+		break;
+	}
+	read_unlock(&ov->att_rwlock);
+
+	ov_info(ov->pdev, "pdi_done: %d", ov->pdi_done);
+
+	/* Clear ready flag */
+	write_lock(&ov->att_rwlock);
+	ov->pdi_ready = 0;
+	zocl_ov_clean(ov);
+	write_unlock(&ov->att_rwlock);
+
+	wait_for_status(ov, XRT_XFR_PKT_STATUS_IDLE);
+	set_version(ov);
+
+	return 0;
+
+fail:
+	write_lock(&ov->att_rwlock);
+	zocl_ov_clean(ov);
+	write_unlock(&ov->att_rwlock);
+
+	wait_for_status(ov, XRT_XFR_PKT_STATUS_IDLE);
+	set_version(ov);
+
+	return ret;
+}
+
+/*
+ * This is the main thread in zocl ospi versal subdriver.
+ *
+ * The thread will wake up every second and check the packet
+ * status. If there is a new packet ready, it will start load and
+ * handle the packets.
+ */
+static int zocl_ov_thread(void *data)
+{
+	struct zocl_ov_dev *ov = (struct zocl_ov_dev *)data;
+	u8 pkt_flags, pkt_type;
+
+	set_status(ov, XRT_XFR_PKT_STATUS_IDLE);
+
+	while (1) {
+		if (kthread_should_stop())
+			break;
+
+		if (check_for_status(ov, XRT_XFR_PKT_STATUS_IDLE)) {
+			msleep(ZOCL_OV_TIMER_INTERVAL);
+			continue;
+		}
+
+		pkt_flags = get_pkt_flags(ov);
+		pkt_type = pkt_flags >> XRT_XFR_PKT_TYPE_SHIFT &
+		    XRT_XFR_PKT_TYPE_MASK;
+		switch (pkt_type) {
+		case XRT_XFR_PKT_TYPE_PDI:
+			zocl_ov_get_pdi(ov);
+			break;
+		case XRT_XFR_PKT_TYPE_XCLBIN:
+			zocl_ov_get_xclbin(ov);
+			break;
+		default:
+			ov_err(ov->pdev, "Unknow packet type: %d", pkt_type);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static const struct of_device_id zocl_ospi_versal_of_match[] = {
+	{ .compatible = "xlnx,ospi_versal",
+	},
+	{ .compatible = "xlnx,mpsoc_ocm",
+	},
+	{ /* end of table */ },
+};
+
+MODULE_DEVICE_TABLE(of, zocl_ospi_versal_of_match);
+
+static int zocl_ov_probe(struct platform_device  *pdev)
+{
+	struct zocl_ov_dev *ov;
+	const struct of_device_id *id;
+	struct resource *res;
+	void __iomem *map;
+	char thread_name[256] = "zocl-ov-thread";
+	int ret;
+
+	id = of_match_node(zocl_ospi_versal_of_match, pdev->dev.of_node);
+	ov_info(pdev, "Probing for %s", id->compatible);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM,
+	    ZOCL_OSPI_VERSAL_BRAM_RES);
+	map = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(map)) {
+		ov_err(pdev, "Unable to map OSPI resource: %0lx",
+		    PTR_ERR(map));
+		return PTR_ERR(map);
+	}
+
+	ov = devm_kzalloc(&pdev->dev, sizeof(*ov), GFP_KERNEL);
+	if (!ov)
+		return -ENOMEM;
+
+	ov->base = map;
+	ov->size = res->end - res->start + 1;
+	memset_io(ov->base, 0, ov->size);
+	ov->pdev = pdev;
+
+	rwlock_init(&ov->att_rwlock);
+
+	ret = zocl_ov_init_sysfs(&pdev->dev);
+	if (ret) {
+		ov_err(pdev, "Unable to create ospi versal sysfs node");
+		kfree(ov);
+		return ret;
+	}
+
+	set_version(ov);
+
+	/* Start the thread. */
+	ov->timer_task = kthread_run(zocl_ov_thread, ov, thread_name);
+	if (IS_ERR(ov->timer_task)) {
+		ret = PTR_ERR(ov->timer_task);
+
+		ov_err(pdev, "Unable to create ospi versal thread");
+		kfree(ov);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, ov);
+
+	return 0;
+}
+
+static int zocl_ov_remove(struct platform_device *pdev)
+{
+	struct zocl_ov_dev *ov = platform_get_drvdata(pdev);
+
+	zocl_ov_fini_sysfs(&pdev->dev);
+
+	if (ov && ov->timer_task)
+		kthread_stop(ov->timer_task);
+
+	return 0;
+}
+
+struct platform_driver zocl_ospi_versal_driver = {
+	.driver = {
+		.name = ZOCL_OSPI_VERSAL_NAME,
+		.of_match_table = zocl_ospi_versal_of_match,
+	},
+	.probe  = zocl_ov_probe,
+	.remove = zocl_ov_remove,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_ov_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_ov_sysfs.c
@@ -0,0 +1,145 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ base
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu   <yliu@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "zocl_drv.h"
+#include "zocl_ospi_versal.h"
+
+static ssize_t pdi_done_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct zocl_ov_dev *ov = dev_get_drvdata(dev);
+	u8 val;
+
+	if (!ov)
+		return 0;
+
+	if (kstrtou8(buf, 16, &val) == -EINVAL)
+		return -EINVAL;
+
+	write_lock(&ov->att_rwlock);
+	ov->pdi_done = val;
+	write_unlock(&ov->att_rwlock);
+
+	return count;
+}
+static DEVICE_ATTR_WO(pdi_done);
+
+static ssize_t pdi_ready_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct zocl_ov_dev *ov = dev_get_drvdata(dev);
+	ssize_t size = 0;
+
+	if (!ov)
+		return 0;
+
+	read_lock(&ov->att_rwlock);
+	size += sprintf(buf, "%d\n", ov->pdi_ready);
+	read_unlock(&ov->att_rwlock);
+
+	return size;
+}
+static DEVICE_ATTR_RO(pdi_ready);
+
+static struct attribute *zocl_ov_attrs[] = {
+	&dev_attr_pdi_ready.attr,
+	&dev_attr_pdi_done.attr,
+	NULL,
+};
+
+static ssize_t read_versal_pdi(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct zocl_ov_dev *ov;
+	struct zocl_ov_pkt_node *node;
+	size_t pre_size = 0, size = 0, cp_size;
+	size_t rem_count = count;
+	loff_t cp_start;
+	u32 nread = 0;
+
+	ov = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!ov)
+		return 0;
+
+	read_lock(&ov->att_rwlock);
+	node = ov->head;
+	if (!node) {
+		read_unlock(&ov->att_rwlock);
+		return 0;
+	}
+
+	while (node) {
+		size += node->zn_size;
+		if (off > size) {
+			node = node->zn_next;
+			pre_size = size;
+			continue;
+		}
+
+		cp_start = off >= pre_size ? off - pre_size : 0;
+		if (node->zn_size - cp_start >= rem_count)
+			cp_size = rem_count;
+		else
+			cp_size = node->zn_size - cp_start;
+		rem_count -= cp_size;
+
+		memcpy(buf + nread, ((char *)node->zn_datap) + cp_start,
+		    cp_size);
+		nread += cp_size;
+		if (rem_count == 0)
+			break;
+
+		pre_size = size;
+		node = node->zn_next;
+	}
+
+	read_unlock(&ov->att_rwlock);
+	return nread;
+}
+
+static struct bin_attribute versal_pdi_attr = {
+	.attr = {
+		.name = "versal_pdi",
+		.mode = 0444
+	},
+	.read = read_versal_pdi,
+	.write = NULL,
+	.size = 0
+};
+
+static struct bin_attribute *zocl_ov_bin_attrs[] = {
+	&versal_pdi_attr,
+	NULL,
+};
+
+static struct attribute_group zocl_ov_attr_group = {
+	.attrs = zocl_ov_attrs,
+	.bin_attrs = zocl_ov_bin_attrs,
+};
+
+int zocl_ov_init_sysfs(struct device *dev)
+{
+	int ret;
+
+	ret = sysfs_create_group(&dev->kobj, &zocl_ov_attr_group);
+	if (ret)
+		DRM_ERROR("Create zocl attrs failed: %d\n", ret);
+
+	return ret;
+}
+
+void zocl_ov_fini_sysfs(struct device *dev)
+{
+	sysfs_remove_group(&dev->kobj, &zocl_ov_attr_group);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_rpu_channel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_rpu_channel.c
@@ -0,0 +1,391 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Lizhi Hou <lizhih@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include "zocl_drv.h"
+#include "zocl_ert_intc.h"
+#include "zocl_xgq.h"
+#include "zocl_xclbin.h"
+
+#define ZRPU_CHANNEL_NAME "zocl_rpu_channel"
+
+#define ZCHAN2PDEV(chan)		((chan)->pdev)
+#define ZCHAN2DEV(chan)			(&ZCHAN2PDEV(chan)->dev)
+#define zchan_err(chan, fmt, args...)	zocl_err(ZCHAN2DEV(chan), fmt"\n", ##args)
+#define zchan_info(chan, fmt, args...)	zocl_info(ZCHAN2DEV(chan), fmt"\n", ##args)
+#define zchan_dbg(chan, fmt, args...)	zocl_dbg(ZCHAN2DEV(chan), fmt"\n", ##args)
+
+/* reserve 4k shared memory for RPU outband communication */
+#define ZRPU_CHANNEL_READY		0
+#define ZRPU_CHANNEL_XGQ_OFF		4
+
+/* hardcode XGQ buffer from offset 4K, size is 4K, too */
+#define ZRPU_CHANNEL_XGQ_BUFFER		4096
+#define ZRPU_CHANNEL_XGQ_BUFFER_SIZE	4096
+#define ZRPU_CHANNEL_XGQ_SLOT_SIZE	1024
+
+struct zocl_rpu_data_entry {
+	struct list_head	entry_list;
+	char			*data_entry;
+	size_t			data_size;
+};
+
+struct zocl_rpu_channel {
+	struct platform_device *pdev;
+	struct platform_device *intc_pdev;
+	void __iomem *mem_base;
+	void __iomem *xgq_base;
+	void *xgq_hdl;
+	u64 mem_start;
+	size_t mem_size;
+	struct list_head	data_list;
+};
+
+static inline void reg_write(void __iomem *base, u64 off, u32 val)
+{
+	iowrite32(val, base + off);
+}
+
+static inline u32 reg_read(void __iomem *base, u64 off)
+{
+	return ioread32(base + off);
+}
+
+static ssize_t ready_store(struct device *dev, struct device_attribute *da,
+	const char *buf, size_t count)
+{
+	struct zocl_rpu_channel *chan = (struct zocl_rpu_channel *)dev_get_drvdata(dev);
+	u32 val;
+
+	if (kstrtou32(buf, 10, &val) < 0 || val != 1) {
+		zchan_err(chan, "invalid input %d\n", val);
+		return -EINVAL;
+	}
+
+	reg_write(chan->mem_base, ZRPU_CHANNEL_READY, 1);
+
+	return count;
+}
+static DEVICE_ATTR_WO(ready);
+
+static struct attribute *zrpu_channel_attrs[] = {
+	&dev_attr_ready.attr,
+	NULL,
+};
+
+static const struct attribute_group zrpu_channel_attrgroup = {
+	.attrs = zrpu_channel_attrs,
+};
+
+static const struct of_device_id zocl_rpu_channel_of_match[] = {
+	{ .compatible = "xlnx,rpu-channel", },
+	{ /* end of table */ },
+};
+
+#define ZCHAN_CMD_HANDLER_VER_MAJOR	1
+#define ZCHAN_CMD_HANDLER_VER_MINOR	0
+
+typedef void (*cmd_handler)(struct zocl_rpu_channel *chan, struct xgq_cmd_sq_hdr *cmd,
+			    struct xgq_com_queue_entry *resp);
+
+static void init_resp(struct xgq_com_queue_entry *resp, u16 cid, u32 rcode)
+{
+	memset(resp, 0, sizeof(*resp));
+	resp->hdr.cid = cid;
+	resp->hdr.cstate = XGQ_CMD_STATE_COMPLETED;
+	resp->rcode = rcode;
+}
+
+static void zchan_cmd_identify(struct zocl_rpu_channel *chan, struct xgq_cmd_sq_hdr *cmd,
+			       struct xgq_com_queue_entry *resp)
+{
+	struct xgq_cmd_resp_identify *r = (struct xgq_cmd_resp_identify *)resp;
+
+	init_resp(resp, cmd->cid, 0);
+
+	r->major = ZCHAN_CMD_HANDLER_VER_MAJOR;
+	r->minor = ZCHAN_CMD_HANDLER_VER_MINOR;
+}
+
+static void zchan_cmd_load_xclbin(struct zocl_rpu_channel *chan, struct xgq_cmd_sq_hdr *cmd,
+	struct xgq_com_queue_entry *resp)
+{
+	struct xgq_cmd_sq *sq = (struct xgq_cmd_sq *)cmd;
+	struct xgq_cmd_cq *cq = (struct xgq_cmd_cq *)resp;
+	u32 address_offset = sq->xclbin_payload.address;
+	u32 size = sq->xclbin_payload.size;
+	u32 remain_size = sq->xclbin_payload.remain_size;
+	struct zocl_rpu_data_entry *entry = NULL;
+	void __iomem *src = chan->mem_base + address_offset;
+	int ret = 0;
+
+	zchan_info(chan, "addr_off 0x%x, size %d, remain %d",
+		address_offset, size, remain_size);
+
+	/*
+	 * if remain_size is not 0, this is not last pkt.
+	 *
+	 * every pkt will be added to linkedlist.
+	 * if this is last pkt, dump linked list to whole xclbin.
+	 */
+	entry = vmalloc(sizeof(struct zocl_rpu_data_entry));
+	if (entry == NULL) {
+		zchan_err(chan, "no memory");
+		ret = -ENOMEM;
+		goto fail;
+	}
+	entry->data_size = size;
+	entry->data_entry = vmalloc(size);
+	memcpy_fromio(entry->data_entry, src, size);
+
+	list_add_tail(&entry->entry_list, &chan->data_list);
+
+	/* remain_size 0 indicates this is the last pkt */
+	if (remain_size == 0) {
+		struct list_head *pos = NULL, *next = NULL;
+		struct zocl_rpu_data_entry *elem = NULL;
+		size_t total_size = 0;
+		char *total_data = NULL;
+		char *cur = NULL;
+		int ret;
+
+		list_for_each_safe(pos, next, &chan->data_list) {
+			elem = list_entry(pos, struct zocl_rpu_data_entry, entry_list);
+			total_size += elem->data_size;
+		}
+
+		total_data = vmalloc(total_size);
+		if (total_data == NULL) {
+			zchan_err(chan, "no memory");
+			ret = -ENOMEM;
+			goto fail;
+		}
+
+		cur = total_data;
+		pos = NULL;
+		next = NULL;
+		list_for_each_safe(pos, next, &chan->data_list) {
+			elem = list_entry(pos, struct zocl_rpu_data_entry, entry_list);
+			
+			memcpy(cur, elem->data_entry, elem->data_size);
+			cur += elem->data_size;
+
+			list_del(pos);
+			vfree(elem->data_entry);
+			vfree(elem);
+		}
+		zchan_info(chan, "total size: %ld list empty %d",
+			   total_size, list_empty(&chan->data_list));
+		INIT_LIST_HEAD(&chan->data_list);
+
+		ret = zocl_xclbin_load_pskernel(zocl_get_zdev(),total_data);
+		if (ret)
+			zchan_err(chan, "failed to cache xclbin: %d", ret);
+
+		vfree(total_data);
+	}
+
+	init_resp(resp, cmd->cid, 0);
+	cq->cq_xclbin_payload.count = size;
+	return;
+fail:
+	/* if list is not empty, clean up memory and re-init list */
+	if (list_empty(&chan->data_list)) {
+		struct list_head *pos = NULL, *next = NULL;
+		struct zocl_rpu_data_entry *elem = NULL;
+
+		list_for_each_safe(pos, next, &chan->data_list) {
+			elem = list_entry(pos, struct zocl_rpu_data_entry, entry_list);
+			list_del(pos);
+			vfree(elem->data_entry);
+			vfree(elem);
+		}
+		INIT_LIST_HEAD(&chan->data_list);
+	}
+	init_resp(resp, cmd->cid, ret);
+	return;
+
+}
+
+static void zchan_cmd_default_handler(struct zocl_rpu_channel *chan, struct xgq_cmd_sq_hdr *cmd,
+				      struct xgq_com_queue_entry *resp)
+{
+	zchan_err(chan, "Unknown cmd: %d", cmd->opcode);
+	init_resp(resp, cmd->cid, -ENOTTY);
+}
+
+struct zchan_ops {
+	u32 op;
+	char *name;
+	cmd_handler handler;
+} zchan_op_table[] = {
+	{ XGQ_CMD_OP_IDENTIFY, "XGQ_CMD_OP_IDENTIFY", zchan_cmd_identify },
+	{ XGQ_CMD_OP_LOAD_XCLBIN, "XGQ_CMD_OP_LOAD_XCLBIN", zchan_cmd_load_xclbin },
+};
+
+static inline const struct zchan_ops *opcode2op(u32 op)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(zchan_op_table); i++) {
+		if (zchan_op_table[i].op == op)
+			return &zchan_op_table[i];
+	}
+	return NULL;
+}
+
+static inline const char *opcode2name(u32 opcode)
+{
+	const struct zchan_ops *op = opcode2op(opcode);
+
+	return op ? op->name : "UNKNOWN_CMD";
+}
+
+static inline cmd_handler opcode2handler(u32 opcode)
+{
+	const struct zchan_ops *op = opcode2op(opcode);
+
+	return op ? op->handler : NULL;
+}
+
+/* All channel command is run-to-complete, no async process is supported. */
+static void zchan_cmd_handler(struct platform_device *pdev, struct xgq_cmd_sq_hdr *cmd)
+{
+	struct zocl_rpu_channel *chan = platform_get_drvdata(pdev);
+	u32 op = cmd->opcode;
+	cmd_handler func = opcode2handler(op);
+	struct xgq_com_queue_entry r = {};
+
+	zchan_info(chan, "%s received", opcode2name(op));
+	if (func)
+		func(chan, cmd, &r);
+	else
+		zchan_cmd_default_handler(chan, cmd, &r);
+	zxgq_send_response(chan->xgq_hdl, &r);
+	kfree(cmd);
+}
+
+static int zrpu_channel_probe(struct platform_device *pdev)
+{
+	const char *mem_res_name = "xlnx,xgq_buffer";
+	const char *xgq_res_name = "xlnx,xgq_device";
+	struct device_node *np = NULL;
+	struct resource res = {};
+	struct zocl_rpu_channel *chan;
+	struct zocl_xgq_init_args xgq_arg = {};
+	int ret;
+	u32 irq;
+
+	chan = devm_kzalloc(&pdev->dev, sizeof(*chan), GFP_KERNEL);
+	if (!chan)
+		return -ENOMEM;
+
+	chan->pdev = pdev;
+	platform_set_drvdata(pdev, chan);
+
+	INIT_LIST_HEAD(&chan->data_list);
+
+	/* Discover and init shared ring buffer. */
+	chan->mem_base = zlib_map_phandle_res_by_name(ZCHAN2PDEV(chan), mem_res_name,
+						      &chan->mem_start, &chan->mem_size);
+	if (!chan->mem_base) {
+		zchan_err(chan, "failed to find channel buffer");
+		return -EINVAL;
+	}
+	reg_write(chan->mem_base, ZRPU_CHANNEL_XGQ_OFF, ZRPU_CHANNEL_XGQ_BUFFER);
+
+	/* Discover and init XGQ. */
+	ret = of_count_phandle_with_args(ZCHAN2DEV(chan)->of_node, xgq_res_name, NULL);
+	if (ret <= 0) {
+		zchan_err(chan, "failed to find RPU channel XGQ");
+		return -EINVAL;
+	}
+	if (ret != 1) {
+		zchan_info(chan, "found > 1 XGQs, only use the first one");
+	}
+	np = of_parse_phandle(ZCHAN2DEV(chan)->of_node, xgq_res_name, 0);
+	if (!np) {
+		zchan_err(chan, "failed to find node for XGQ");
+		return -EINVAL;
+	}
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret) {
+		zchan_err(chan, "failed to find res for XGQ: %d", ret);
+		return -EINVAL;
+	}
+	irq = of_irq_get(np, 0);
+	zchan_info(chan, "Found XGQ @ %pR on irq %d", &res, irq);
+	chan->xgq_base = zlib_map_res(ZCHAN2DEV(chan), &res, NULL, NULL);
+	if (!chan->xgq_base) {
+		zchan_err(chan, "failed to map XGQ IP");
+		return -EINVAL;
+	}
+
+	ret = sysfs_create_group(&ZCHAN2DEV(chan)->kobj, &zrpu_channel_attrgroup);
+	if (ret) {
+		zchan_err(chan, "failed to create sysfs: %d", ret);
+		return ret;
+	}
+
+	/* Bringup INTC sub-dev to handle interrupts for this XGQ. */
+	ret = zocl_ert_create_intc(ZCHAN2DEV(chan), &irq, 1, 0,
+				   ERT_XGQ_INTC_DEV_NAME, &chan->intc_pdev);
+	if (ret) {
+		zchan_err(chan, "Failed to create xgq intc device: %d", ret);
+		goto err_intc;
+	}
+
+	/* Bringup the XGQ. */
+	xgq_arg.zxia_pdev = ZCHAN2PDEV(chan);
+	xgq_arg.zxia_ring = chan->mem_base + ZRPU_CHANNEL_XGQ_BUFFER;
+	xgq_arg.zxia_ring_size = ZRPU_CHANNEL_XGQ_BUFFER_SIZE;
+	xgq_arg.zxia_ring_slot_size = ZRPU_CHANNEL_XGQ_SLOT_SIZE;
+	xgq_arg.zxia_irq = irq;
+	xgq_arg.zxia_intc_pdev = chan->intc_pdev;
+	xgq_arg.zxia_xgq_ip = chan->xgq_base;
+	xgq_arg.zxia_cmd_handler = zchan_cmd_handler;
+	chan->xgq_hdl = zxgq_init(&xgq_arg);
+	if (!chan->xgq_hdl) {
+		zchan_err(chan, "failed to initialize XGQ");
+		goto err_xgq;
+	}
+
+	return 0;
+
+err_xgq:
+	zocl_ert_destroy_intc(chan->intc_pdev);
+err_intc:
+	sysfs_remove_group(&pdev->dev.kobj, &zrpu_channel_attrgroup);
+	return -EINVAL;
+};
+
+static int zrpu_channel_remove(struct platform_device *pdev)
+{
+	struct zocl_rpu_channel *chan = platform_get_drvdata(pdev);
+
+	if (chan->xgq_hdl)
+		zxgq_fini(chan->xgq_hdl);
+	zocl_ert_destroy_intc(chan->intc_pdev);
+	sysfs_remove_group(&pdev->dev.kobj, &zrpu_channel_attrgroup);
+	return 0;
+};
+
+struct platform_driver zocl_rpu_channel_driver = {
+	.driver = {
+		.name = ZRPU_CHANNEL_NAME,
+		.of_match_table = zocl_rpu_channel_of_match,
+	},
+	.probe = zrpu_channel_probe,
+	.remove = zrpu_channel_remove,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_sk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_sk.c
@@ -0,0 +1,256 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style (optionally CMA backed) device manager for ZynQ based
+ * OpenCL accelerators.
+ *
+ * Copyright (C) 2019-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Larry Liu       <yliu@xilinx.com>
+ *    Jeff Lin        <jeffli@xilinx.com>
+ *    Jan Stephan     <j.stephan@hzdr.de>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "ert.h"
+#include "zocl_drv.h"
+#include "zocl_cu.h"
+#include "zocl_sk.h"
+
+int
+zocl_sk_getcmd_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_dev *zdev = dev->dev_private;
+	struct soft_krnl *sk = zdev->soft_kernel;
+	struct soft_krnl_cmd *scmd;
+	struct drm_zocl_sk_getcmd *kdata = data;
+
+	/* If no command, the process who calls this ioctl will block here */
+	mutex_lock(&sk->sk_lock);
+	while (list_empty(&sk->sk_cmd_list)) {
+		mutex_unlock(&sk->sk_lock);
+		if (wait_event_interruptible(sk->sk_wait_queue,
+		    !list_empty(&sk->sk_cmd_list)))
+			return -ERESTARTSYS;
+		mutex_lock(&sk->sk_lock);
+	}
+
+	scmd = list_first_entry(&sk->sk_cmd_list, struct soft_krnl_cmd,
+	    skc_list);
+	list_del(&scmd->skc_list);
+	mutex_unlock(&sk->sk_lock);
+
+	kdata->opcode = scmd->skc_opcode;
+
+	if (kdata->opcode == ERT_SK_CONFIG) {
+		struct config_sk_image_uuid *cmd = NULL;
+		u32 bohdl = 0xffffffff;
+		u32 meta_bohdl = 0xffffffff;
+		int i, ret;
+
+		cmd = scmd->skc_packet;
+
+		if (sk->sk_meta_bohdl >= 0) {
+			meta_bohdl = sk->sk_meta_bohdl;
+		} else {
+			ret = drm_gem_handle_create(filp,
+						    &sk->sk_meta_bo->cma_base.base, &meta_bohdl);
+
+			if (ret) {
+				DRM_WARN("%s Failed create metadata BO handle: %d\n",
+					 __func__, ret);
+				meta_bohdl = 0xffffffff;
+			} else {
+				sk->sk_meta_bohdl = meta_bohdl;
+				DRM_INFO("sk_meta_data BO handle 0x%x created\n",meta_bohdl);
+			}
+		}
+
+		for (i = 0; i < sk->sk_nimg; i++) {
+			if(strcmp(sk->sk_img[i].scu_name,(char *)cmd->sk_name)!=0) {
+				DRM_INFO("SK image name %s not matching sk_name %s\n",
+					 sk->sk_img[i].scu_name,(char *)cmd->sk_name);
+				continue;
+			}
+			DRM_INFO("Found SK image name %s matching sk_name %s\n",
+				 sk->sk_img[i].scu_name,(char *)cmd->sk_name);
+
+			if (sk->sk_img[i].si_bohdl >= 0) {
+				bohdl = sk->sk_img[i].si_bohdl;
+				break;
+			}
+
+			ret = drm_gem_handle_create(filp,
+			    &sk->sk_img[i].si_bo->cma_base.base, &bohdl);
+
+			if (ret) {
+				DRM_WARN("%s Failed create BO handle: %d\n",
+				    __func__, ret);
+				bohdl = 0xffffffff;
+			} else {
+				sk->sk_img[i].si_bohdl = bohdl;
+				DRM_INFO("sk_img[%d] BO handle %d created\n",i,bohdl);
+			}
+
+			break;
+		}
+
+		/* Copy the command to ioctl caller */
+		kdata->start_cuidx = cmd->start_cuidx;
+		kdata->cu_nums = cmd->num_cus;
+		kdata->bohdl = bohdl;
+		kdata->meta_bohdl = meta_bohdl;
+		memcpy(kdata->uuid,cmd->sk_uuid,sizeof(kdata->uuid));
+
+		snprintf(kdata->name, ZOCL_MAX_NAME_LENGTH, "%s",
+		    (char *)cmd->sk_name);
+	} else
+		/* We will handle more opcodes */
+		DRM_WARN("Unknown soft kernel command: %d\n",
+		    kdata->opcode);
+
+	kfree(scmd);
+	return 0;
+}
+
+int
+zocl_sk_create_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
+{
+	struct drm_zocl_sk_create *args = data;
+	uint32_t cu_idx = args->cu_idx;
+	struct platform_device *zert = zocl_find_pdev("ert_hw");
+	struct platform_device *scu_pdev = NULL;
+	struct zocl_cu *scu = NULL;
+	int boHandle = -1;
+	int ret = 0;
+	
+	if (cu_idx >= MAX_SOFT_KERNEL) {
+		DRM_ERROR("Fail to create soft kernel: CU index %d > %d.\n",
+			  cu_idx,MAX_SOFT_KERNEL);
+		return -EINVAL;
+	}
+
+	if(!zert) {
+		DRM_ERROR("ERT not found!");
+		return -EINVAL;
+	}
+	scu_pdev = zert_get_scu_pdev(zert, cu_idx);
+     	scu = platform_get_drvdata(scu_pdev);
+	if (!scu) {
+		DRM_ERROR("SCU %d does not exist.\n", cu_idx);
+		return -EINVAL;
+	}
+
+	ret = zocl_scu_create_sk(scu_pdev,task_pid_nr(current),task_ppid_nr(current), filp, &boHandle);
+	if (ret) {
+		DRM_WARN("%s Failed to create SK command BO handle: %d\n",
+			 __func__, ret);
+		boHandle = 0xffffffff;
+	}
+	
+	args->handle = boHandle;
+	return ret;
+}
+
+int
+zocl_sk_report_ioctl(struct drm_device *dev, void *data,
+		struct drm_file *filp)
+{
+	struct drm_zocl_sk_report *args = data;
+	struct zocl_cu *scu = NULL;
+	uint32_t cu_idx = args->cu_idx;
+	enum drm_zocl_scu_state state = args->cu_state;
+	int ret = 0;
+	struct platform_device *zert = zocl_find_pdev("ert_hw");
+	struct platform_device *scu_pdev = NULL;
+	
+	if(!zert) {
+		DRM_ERROR("ERT not found!");
+		return -EINVAL;
+	}
+	scu_pdev = zert_get_scu_pdev(zert, cu_idx);
+	if (!scu_pdev) {
+		DRM_ERROR("SCU %d does not exist.\n", cu_idx);
+		return -EINVAL;
+	}
+
+	scu = platform_get_drvdata(scu_pdev);
+	if (!scu) {
+		DRM_ERROR("SCU %d does not exist.\n", cu_idx);
+		return -EINVAL;
+	}
+
+	switch (state) {
+
+	case ZOCL_SCU_STATE_DONE:
+
+		ret = zocl_scu_wait_cmd_sk(scu_pdev);
+		break;
+
+	case ZOCL_SCU_STATE_READY:
+
+		zocl_scu_sk_ready(scu_pdev);
+		break;
+
+	case ZOCL_SCU_STATE_CRASH:
+
+		zocl_scu_sk_crash(scu_pdev);
+		break;
+
+	case ZOCL_SCU_STATE_FINI:
+		zocl_scu_sk_fini(scu_pdev);
+		break;
+
+	default:
+		/*
+		 * More soft kernel state will be added as the kernel
+		 * is not completed but ready to take another run.
+		 */
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+int
+zocl_init_soft_kernel(struct drm_zocl_dev *zdev)
+{
+	struct soft_krnl *sk;
+
+	sk = devm_kzalloc(zdev->ddev->dev, sizeof(*sk), GFP_KERNEL);
+	if (!sk)
+		return -ENOMEM;
+
+	zdev->soft_kernel = sk;
+	mutex_init(&sk->sk_lock);
+	INIT_LIST_HEAD(&sk->sk_cmd_list);
+	init_waitqueue_head(&sk->sk_wait_queue);
+
+	return 0;
+}
+
+void
+zocl_fini_soft_kernel(struct drm_zocl_dev *zdev)
+{
+	struct soft_krnl *sk;
+	int i;
+
+	sk = zdev->soft_kernel;
+	mutex_lock(&sk->sk_lock);
+
+	if(!IS_ERR(&sk->sk_meta_bo)) {
+		zocl_drm_free_bo(sk->sk_meta_bo);
+	}
+	
+	for (i = 0; i < sk->sk_nimg; i++) {
+		if (IS_ERR(&sk->sk_img[i].si_bo))
+			continue;
+		zocl_drm_free_bo(sk->sk_img[i].si_bo);
+	}
+	kfree(sk->sk_img);
+
+	mutex_unlock(&sk->sk_lock);
+	mutex_destroy(&sk->sk_lock);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_sysfs.c
@@ -0,0 +1,722 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * A GEM style device manager for PCIe based OpenCL accelerators.
+ *
+ * Copyright (C) 2016-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include "zocl_drv.h"
+#include "zocl_aie.h"
+#include "sched_exec.h"
+#include "zocl_xclbin.h"
+#include "xclbin.h"
+#include "zocl_sk.h"
+#include "kds_core.h"
+
+extern int kds_echo;
+
+/* -KDS sysfs-- */
+static ssize_t
+kds_echo_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return sprintf(buf, "%d\n", kds_echo);
+}
+
+static ssize_t
+kds_echo_store(struct device *dev, struct device_attribute *da,
+	       const char *buf, size_t count)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+
+	return store_kds_echo(&zdev->kds, buf, count, &kds_echo);
+}
+static DEVICE_ATTR(kds_echo, 0644, kds_echo_show, kds_echo_store);
+
+static ssize_t
+kds_stat_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+
+	return show_kds_stat(&zdev->kds, buf);
+}
+static DEVICE_ATTR_RO(kds_stat);
+
+static ssize_t
+kds_custat_raw_show(struct device *dev, struct device_attribute *attr,
+		    char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+
+	return show_kds_custat_raw(&zdev->kds, buf);
+}
+static DEVICE_ATTR_RO(kds_custat_raw);
+
+static ssize_t xclbinid_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	struct drm_zocl_slot *zocl_slot = NULL;
+	const char *raw_fmt = "%d %pUb\n";
+	ssize_t size = 0;
+	ssize_t count = 0;
+	int i = 0;
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+		if (!zocl_slot || !zocl_slot->slot_xclbin ||
+		    !zocl_slot->slot_xclbin->zx_uuid)
+			return 0;
+
+		count = sprintf(buf+size, raw_fmt, zocl_slot->slot_idx,
+				zocl_slot->slot_xclbin->zx_uuid);
+		size += count;
+	}
+
+	return size;
+}
+static DEVICE_ATTR_RO(xclbinid);
+
+static ssize_t dtbo_path_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	struct drm_zocl_slot *zocl_slot = NULL;
+	const char *raw_fmt = "%d %s\n";
+	ssize_t size = 0;
+	ssize_t count = 0;
+	int i = 0;
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+		if (!zocl_slot || !zocl_slot->slot_xclbin ||
+		    !zocl_slot->slot_xclbin->zx_dtbo_path)
+			continue;
+
+		count = sprintf(buf+size, raw_fmt, zocl_slot->slot_idx,
+				zocl_slot->slot_xclbin->zx_dtbo_path);
+		size += count;
+	}
+
+	return size;
+}
+static DEVICE_ATTR_RO(dtbo_path);
+
+static ssize_t kds_numcus_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	struct kds_sched *kds = &zdev->kds;
+	ssize_t size;
+
+	if (!zdev || !kds)
+		return 0;
+
+	size = sprintf(buf, "%d\n", kds->cu_mgmt.num_cus);
+
+	return size;
+}
+static DEVICE_ATTR_RO(kds_numcus);
+
+static ssize_t kds_skstat_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	struct soft_krnl *sk;
+	struct soft_cu *scu;
+	ssize_t sz = 0;
+	int i;
+
+	if (!zdev || !zdev->soft_kernel)
+		return 0;
+
+	sk = zdev->soft_kernel;
+	mutex_lock(&sk->sk_lock);
+	for (i = 0; i < sk->sk_ncus; i++) {
+		scu = sk->sk_cu[i];
+		if (scu) {
+			sz += sprintf(buf+sz, "SK %d\n", i);
+			sz += sprintf(buf+sz, " flags %d\n", scu->sc_flags);
+			sz += sprintf(buf+sz, " usage %lld\n", scu->usage);
+			sz += sprintf(buf+sz, " vregs[0] 0x%x\n", ((u32*)scu->sc_vregs)[0]);
+		} else {
+			sz += sprintf(buf+sz, "SK %d is released\n", i);
+		}
+	}
+	mutex_unlock(&sk->sk_lock);
+
+	return sz;
+}
+static DEVICE_ATTR_RO(kds_skstat);
+
+static ssize_t
+kds_interval_store(struct device *dev, struct device_attribute *da,
+	       const char *buf, size_t count)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	u32 interval;
+
+	if (kstrtou32(buf, 10, &interval) == -EINVAL)
+		return -EINVAL;
+
+	zdev->kds.interval = interval;
+
+	return count;
+}
+
+static ssize_t
+kds_interval_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%d\n", zdev->kds.interval);
+}
+static DEVICE_ATTR(kds_interval, 0644, kds_interval_show, kds_interval_store);
+
+static ssize_t kds_xrt_version_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	ssize_t sz = 0;
+
+	if (!zdev || !zdev->soft_kernel)
+		return 0;
+
+	sz += sprintf(buf+sz, "XRT GIT BRANCH: %s\n", XRT_BRANCH);
+	sz += sprintf(buf+sz, "XRT GIT HASH: %s\n", XRT_HASH);
+	sz += sprintf(buf+sz, "XRT GIT HASH DATE: %s\n", XRT_HASH_DATE);
+	sz += sprintf(buf+sz, "XRT GIT Modified Files: %s\n", XRT_MODIFIED_FILES);
+
+	return sz;
+}
+static DEVICE_ATTR_RO(kds_xrt_version);
+
+static ssize_t zocl_get_memstat(struct device *dev, char *buf, bool raw)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	struct zocl_mem *memp = NULL;
+	ssize_t size = 0;
+	ssize_t count = 0;
+	size_t memory_usage = 0;
+	unsigned int bo_count = 0;
+	const char *txt_fmt = "[%s] 0x%012llx\t(%4lluMB):\t%lluKB\t%dBOs\n";
+	const char *raw_fmt = "%llu %d %llu\n";
+
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+        list_for_each_entry(memp, &zdev->zm_list_head, link) {
+		if (memp->zm_type == ZOCL_MEM_TYPE_STREAMING)
+			continue;
+
+		memory_usage = memp->zm_stat.memory_usage;
+		bo_count = memp->zm_stat.bo_count;
+
+		if (raw)
+			count = sprintf(buf, raw_fmt, memory_usage, bo_count, 0);
+		else {
+			count = sprintf(buf, txt_fmt,
+			    memp->zm_used ? "IN-USE" : "UNUSED",
+			    memp->zm_base_addr,
+			    memp->zm_size / 1024,
+			    memory_usage / 1024,
+			    bo_count);
+		}
+		buf += count;
+		size += count;
+	}
+
+	read_unlock(&zdev->attr_rwlock);
+
+	return size;
+}
+
+static ssize_t graph_status_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct aie_info *aie;
+	struct aie_info_cmd *acmd;
+	struct aie_info_packet *aiec_packet;
+	ssize_t nread = 0;
+	zdev = dev_get_drvdata(dev);
+	if (!zdev)
+		return 0;
+
+	aie = zdev->aie_information;
+	if (!aie)
+		return 0;
+
+	/* create request */
+	acmd = kmalloc(sizeof(struct aie_info_cmd), GFP_KERNEL);
+	if (!acmd) {
+		return -ENOMEM;
+	}
+
+	aiec_packet = kmalloc(sizeof(struct aie_info_packet), GFP_KERNEL);
+	if (!aiec_packet) {
+		return -ENOMEM;
+	}
+
+	/* set command */
+	aiec_packet->opcode = GRAPH_STATUS;
+	acmd->aiec_packet = aiec_packet;
+
+	/* init semaphore */
+	sema_init(&acmd->aiec_sem, 0);
+
+	/* caller release the wait aied thread and wait for result */
+	mutex_lock(&aie->aie_lock);
+	if (waitqueue_active(&aie->aie_wait_queue)) {
+		list_add_tail(&acmd->aiec_list, &aie->aie_cmd_list);
+		mutex_unlock(&aie->aie_lock);
+		wake_up_interruptible(&aie->aie_wait_queue);
+		if (down_interruptible(&acmd->aiec_sem)) {
+			nread = -ERESTARTSYS;
+			goto clean;
+		}
+	} else {
+		mutex_unlock(&aie->aie_lock);
+		nread =  -ERESTARTSYS;
+		goto clean;
+	}
+
+	nread = snprintf(buf, acmd->aiec_packet->size, "%s\n", acmd->aiec_packet->info);
+
+clean:
+	kfree(acmd->aiec_packet);
+	kfree(acmd);
+	return nread;
+}
+static DEVICE_ATTR_RO(graph_status);
+
+static ssize_t read_aie_metadata(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *zocl_slot = NULL;
+	size_t size = 0;
+	u32 nread = 0;
+	u32 f_nread = 0;
+	int i = 0;
+
+	zdev = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+
+		size = zocl_slot->aie_data.size;
+
+		/* Read offset should be lesser then total size of metadata */
+		if (off >= size) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		/* Buffer size should be greater than the size of metadata to be read */
+		if (count < size - off)
+			nread = count;
+		else
+			nread = size - off;
+
+		memcpy(buf, (char *)zocl_slot->aie_data.data + off, nread);
+
+		buf += nread;
+		f_nread += nread;
+	}
+	read_unlock(&zdev->attr_rwlock);
+
+	return f_nread;
+}
+
+static ssize_t memstat_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	return zocl_get_memstat(dev, buf, false);
+}
+static DEVICE_ATTR_RO(memstat);
+
+static ssize_t memstat_raw_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	return zocl_get_memstat(dev, buf, true);
+}
+static DEVICE_ATTR_RO(memstat_raw);
+
+static ssize_t errors_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct drm_zocl_dev *zdev = dev_get_drvdata(dev);
+	ssize_t size = 0;
+	xrtErrorCode error_code;
+	u64 timestamp;
+	int i;
+
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	if (!zdev->zdev_error.ze_err) {
+		read_unlock(&zdev->attr_rwlock);
+		return 0;
+	}
+
+	for (i = 0; i < zdev->zdev_error.ze_num; i++) {
+		error_code = zdev->zdev_error.ze_err[i].zer_err_code;
+		timestamp = zdev->zdev_error.ze_err[i].zer_ts;
+		size += sprintf(buf + size, "%llu%20llu\n",
+		    error_code, timestamp);
+	}
+
+	read_unlock(&zdev->attr_rwlock);
+
+	return size;
+}
+static DEVICE_ATTR_RO(errors);
+
+static struct attribute *zocl_attrs[] = {
+	&dev_attr_xclbinid.attr,
+	&dev_attr_kds_numcus.attr,
+	&dev_attr_kds_skstat.attr,
+	&dev_attr_kds_xrt_version.attr,
+	&dev_attr_kds_echo.attr,
+	&dev_attr_kds_stat.attr,
+	&dev_attr_kds_custat_raw.attr,
+	&dev_attr_kds_interval.attr,
+	&dev_attr_memstat.attr,
+	&dev_attr_memstat_raw.attr,
+	&dev_attr_errors.attr,
+	&dev_attr_graph_status.attr,
+	&dev_attr_dtbo_path.attr,
+	NULL,
+};
+
+static ssize_t read_debug_ip_layout(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *zocl_slot = NULL;
+	size_t size = 0;
+	u32 nread = 0;
+	u32 f_nread = 0;
+	int i = 0;
+
+	zdev = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+
+		if (!zocl_slot->debug_ip) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		size = sizeof_section(zocl_slot->debug_ip, m_debug_ip_data);
+
+		if (off >= size) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		if (count < size - off)
+			nread = count;
+		else
+			nread = size - off;
+
+		memcpy(buf, ((char *)zocl_slot->debug_ip) + off, nread);
+		buf += nread;
+		f_nread += nread;
+	}
+	read_unlock(&zdev->attr_rwlock);
+
+	return f_nread;
+}
+
+static ssize_t read_ip_layout(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *zocl_slot = NULL;
+	size_t size = 0;
+	u32 nread = 0;
+	u32 f_nread = 0;
+	int i = 0;
+
+	zdev = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+
+		if (!zocl_slot->ip) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		size = sizeof_section(zocl_slot->ip, m_ip_data);
+
+		if (off >= size) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		if (count < size - off)
+			nread = count;
+		else
+			nread = size - off;
+
+		memcpy(buf, ((char *)zocl_slot->ip) + off, nread);
+		buf += nread;
+		f_nread += nread;
+	}
+	read_unlock(&zdev->attr_rwlock);
+
+	return f_nread;
+}
+
+static ssize_t read_connectivity(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *zocl_slot = NULL;
+	size_t size = 0;
+	u32 nread = 0;
+	u32 f_nread = 0;
+	int i = 0;
+
+	zdev = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+
+		if (!zocl_slot->connectivity) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		size = sizeof_section(zocl_slot->connectivity, m_connection);
+
+		if (off >= size) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		if (count < size - off)
+			nread = count;
+		else
+			nread = size - off;
+
+		memcpy(buf, ((char *)zocl_slot->connectivity + off), nread);
+		buf += nread;
+		f_nread += nread;
+	}
+	read_unlock(&zdev->attr_rwlock);
+
+	return f_nread;
+}
+
+static ssize_t read_mem_topology(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *zocl_slot = NULL;
+	size_t size = 0;
+	u32 nread = 0;
+	u32 f_nread = 0;
+	int i = 0;
+
+	zdev = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+
+		if (!zocl_slot->topology) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		size = sizeof_section(zocl_slot->topology, m_mem_data);
+
+		if (off >= size) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		if (count < size - off)
+			nread = count;
+		else
+			nread = size - off;
+
+		memcpy(buf, ((char *)zocl_slot->topology + off), nread);
+		buf += nread;
+		f_nread += nread;
+	}
+
+	read_unlock(&zdev->attr_rwlock);
+
+	return f_nread;
+}
+
+static ssize_t read_xclbin_full(struct file *filp, struct kobject *kobj,
+		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+	struct drm_zocl_dev *zdev = NULL;
+	struct drm_zocl_slot *zocl_slot = NULL;
+	size_t size = 0;
+	u32 nread = 0;
+	u32 f_nread = 0;
+	int i = 0;
+
+	zdev = dev_get_drvdata(container_of(kobj, struct device, kobj));
+	if (!zdev)
+		return 0;
+
+	read_lock(&zdev->attr_rwlock);
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+
+		if (!zocl_slot->axlf) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		size = zocl_slot->axlf_size;
+
+		if (off >= size) {
+			read_unlock(&zdev->attr_rwlock);
+			return 0;
+		}
+
+		if (count < size - off)
+			nread = count;
+		else
+			nread = size - off;
+
+		memcpy(buf, ((char *)zocl_slot->axlf + off), nread);
+
+		buf += nread;
+		f_nread += nread;
+	}
+	read_unlock(&zdev->attr_rwlock);
+
+	return f_nread;
+}
+
+static struct bin_attribute aie_metadata_attr = {
+	.attr = {
+		.name = "aie_metadata",
+		.mode = 0444
+	},
+	.read = read_aie_metadata,
+	.write = NULL,
+	.size = 0
+};
+
+static struct bin_attribute debug_ip_layout_attr = {
+	.attr = {
+		.name = "debug_ip_layout",
+		.mode = 0444
+	},
+	.read = read_debug_ip_layout,
+	.write = NULL,
+	.size = 0
+};
+
+static struct bin_attribute ip_layout_attr = {
+	.attr = {
+		.name = "ip_layout",
+		.mode = 0444
+	},
+	.read = read_ip_layout,
+	.write = NULL,
+	.size = 0
+};
+
+static struct bin_attribute connectivity_attr = {
+	.attr = {
+		.name = "connectivity",
+		.mode = 0444
+	},
+	.read = read_connectivity,
+	.write = NULL,
+	.size = 0
+};
+
+static struct bin_attribute mem_topology_attr = {
+	.attr = {
+		.name = "mem_topology",
+		.mode = 0444
+	},
+	.read = read_mem_topology,
+	.write = NULL,
+	.size = 0
+};
+
+static struct bin_attribute xclbin_full_attr = {
+	.attr = {
+		.name = "xclbin_full",
+		.mode = 0444
+	},
+	.read = read_xclbin_full,
+	.write = NULL,
+	.size = 0
+};
+
+
+static struct bin_attribute *zocl_bin_attrs[] = {
+	&debug_ip_layout_attr,
+	&ip_layout_attr,
+	&connectivity_attr,
+	&mem_topology_attr,
+	&aie_metadata_attr,
+	&xclbin_full_attr,
+	NULL,
+};
+
+static struct attribute_group zocl_attr_group = {
+	.attrs = zocl_attrs,
+	.bin_attrs = zocl_bin_attrs,
+};
+
+int zocl_init_sysfs(struct device *dev)
+{
+	int ret;
+
+	ret = sysfs_create_group(&dev->kobj, &zocl_attr_group);
+	if (ret)
+		DRM_ERROR("Create zocl attrs failed: %d\n", ret);
+
+	return ret;
+}
+
+void zocl_fini_sysfs(struct device *dev)
+{
+	sysfs_remove_group(&dev->kobj, &zocl_attr_group);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_watchdog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_watchdog.c
@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2020 Xilinx, Inc. All rights reserved.
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+#include "zocl_drv.h"
+#include "zocl_watchdog.h"
+
+#define watchdog_err(pdev, fmt, args...)  \
+	zocl_err(&pdev->dev, fmt"\n", ##args)
+#define watchdog_info(pdev, fmt, args...)  \
+	zocl_info(&pdev->dev, fmt"\n", ##args)
+#define watchdog_dbg(pdev, fmt, args...)  \
+	zocl_dbg(&pdev->dev, fmt"\n", ##args)
+
+/*
+ * do nothing so far
+ */ 
+static void watchdog_init(struct zocl_watchdog_dev *watchdog)
+{
+}
+
+/*
+ * reset counter part to 0.
+ * 0 has special meaning -- nothing is monitored
+ */ 
+static void watchdog_fini(struct zocl_watchdog_dev *watchdog)
+{
+	u32 val;
+	val = ioread32(watchdog->base + WATCHDOG_OFFSET);
+	val &= RESET_MASK;
+	iowrite32(val, watchdog->base + WATCHDOG_OFFSET);
+}
+
+/*
+ * if everyting is running, increase the counter by 1, set to 1 if overflow 
+ * otherwise, just set the state bit for each individual being monitored
+ */ 
+static void watchdog_config(struct zocl_watchdog_dev *watchdog,
+	struct watchdog_cfg cfg)
+{
+	u32 val;
+	u8 counter;
+	val = ioread32(watchdog->base + WATCHDOG_OFFSET);
+	counter = (val & COUNTER_MASK) >> COUNTER_BITS_SHIFT;
+
+	/*
+	 * counter 0 has special meaning. So if just started,
+	 * set counter as 1
+	 */
+	if (!counter)
+		counter++;
+
+	/* only update counter when everything is running */
+	if (cfg.skd_run && cfg.cmc_run && cfg.cq_thread_run &&
+		cfg.sched_thread_run) {
+		if (counter == (COUNTER_MASK >> COUNTER_BITS_SHIFT))
+			counter = 1;
+		else
+			counter++;
+	}
+	val = (counter << COUNTER_BITS_SHIFT) +
+	       (val & RESET_MASK) +
+	       (cfg.skd_run ? 1 << SKD_BIT_SHIFT : 0) +
+	       (cfg.cmc_run ? 1 << CMC_BIT_SHIFT : 0) +
+	       (cfg.cq_thread_run ? 1 << CQ_THD_BIT_SHIFT : 0) +
+	       (cfg.sched_thread_run ? 1 << SCHED_THD_BIT_SHIFT : 0);
+	iowrite32(val, watchdog->base + WATCHDOG_OFFSET);
+}
+
+static struct zocl_watchdog_ops watchdog_ops = {
+	.init         = watchdog_init,
+	.fini         = watchdog_fini,
+	.config       = watchdog_config,
+};
+
+static const struct of_device_id zocl_watchdog_of_match[] = {
+	{ .compatible = "xlnx,reset_ps",
+	  .data = &watchdog_ops,
+	},
+	{ /* end of table */ },
+};
+
+MODULE_DEVICE_TABLE(of, zocl_watchdog_of_match);
+
+static int zocl_watchdog_probe(struct platform_device *pdev)
+{
+	struct zocl_watchdog_dev *watchdog;
+	const struct of_device_id *id;
+	struct resource *res;
+	const struct zocl_watchdog_ops *ops;
+	void __iomem *map;
+
+	id = of_match_node(zocl_watchdog_of_match, pdev->dev.of_node);
+	watchdog_info(pdev, "Probing for %s", id->compatible);
+
+	watchdog = devm_kzalloc(&pdev->dev, sizeof(*watchdog), GFP_KERNEL);
+	watchdog->pdev = pdev;
+
+	ops = of_device_get_match_data(&pdev->dev);
+	watchdog->ops = ops;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	map = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(map)) {
+		watchdog_err(pdev, "Failed to map reset controller HW registers:"
+			" %0lx", PTR_ERR(map));
+		return PTR_ERR(map);
+	}
+	watchdog->base = map;
+	watchdog_info(pdev, "IP(reset controller) IO start %lx, end %lx",
+	      (unsigned long)res->start, (unsigned long)res->end);
+
+	platform_set_drvdata(pdev, watchdog);
+	return 0;
+}
+
+static int zocl_watchdog_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+struct platform_driver zocl_watchdog_driver = {
+	.driver = {
+		.name = ZOCL_WATCHDOG_NAME,
+		.of_match_table = zocl_watchdog_of_match,
+	},
+	.probe  = zocl_watchdog_probe,
+	.remove = zocl_watchdog_remove,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_xclbin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_xclbin.c
@@ -0,0 +1,1749 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * MPSoC based OpenCL accelerators Compute Units.
+ *
+ * Copyright (C) 2019-2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    David Zhang <davidzha@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/of.h>
+#include "sched_exec.h"
+#include "zocl_xclbin.h"
+#include "zocl_aie.h"
+#include "zocl_sk.h"
+#include "xrt_xclbin.h"
+#include "xclbin.h"
+
+/*
+ * Load xclbin using FPGA manager
+ *
+ * @param       zdev:    zocl device structure
+ * @param       data:   xclbin data buffer pointer
+ * @param       size:   xclbin data buffer size
+ * @param       flag:   FPGA Manager flags
+ *
+ * @return      0 on success, Error code on failure.
+ */
+static int
+zocl_fpga_mgr_load(struct drm_zocl_dev *zdev, const char *data, int size,
+		   u32 flags)
+{
+	struct drm_device *ddev = zdev->ddev;
+	struct device *dev = ddev->dev;
+	struct fpga_manager *fpga_mgr = zdev->fpga_mgr;
+	struct fpga_image_info *info = NULL;
+	int err = 0;
+
+	 /* On Non PR platform, it shouldn't never go to this point.
+	  * On PR platform, the fpga_mgr should be alive.
+	  */
+	if (!zdev->fpga_mgr) {
+		DRM_ERROR("FPGA manager is not found\n");
+		return -ENXIO;
+	}
+
+	/* Allocate an FPGA image info struct */
+	info = fpga_image_info_alloc(dev);
+	if (!info)
+		return -ENOMEM;
+
+	info->flags = flags;
+	info->buf = data;
+	info->count = size;
+
+	/* load FPGA from buffer */
+	err = fpga_mgr_load(fpga_mgr, info);
+	if (err == 0)
+		DRM_INFO("FPGA Manager load DONE");
+	else
+		DRM_ERROR("FPGA Manager load FAILED: %d", err);
+
+	fpga_image_info_free(info);
+
+	return err;
+}
+
+/*
+ * Load partial bitstream to PR platform
+ *
+ * @param       zdev:   zocl device structure
+ * @param       buffer: xclbin data buffer pointer
+ * @param       length: xclbin data buffer size
+ * @param       slot: 	Target slot structure
+ *
+ * @return      0 on success, Error code on failure.
+ */
+static int
+zocl_load_partial(struct drm_zocl_dev *zdev, const char *buffer, int length,
+		  struct drm_zocl_slot *slot)
+{
+	int err = 0;
+	void __iomem *map = NULL;
+
+	if (!slot->pr_isolation_addr) {
+		DRM_ERROR("PR isolation address is not set");
+		return -ENODEV;
+	}
+
+	map = ioremap(slot->pr_isolation_addr, PR_ISO_SIZE);
+	if (IS_ERR_OR_NULL(map)) {
+		DRM_ERROR("ioremap PR isolation address 0x%llx failed",
+		    slot->pr_isolation_addr);
+		return -EFAULT;
+	}
+
+	/* Freeze PR ISOLATION IP for bitstream download */
+	iowrite32(slot->pr_isolation_freeze, map);
+	err = zocl_fpga_mgr_load(zdev, buffer, length, FPGA_MGR_PARTIAL_RECONFIG);
+	/* Unfreeze PR ISOLATION IP */
+	iowrite32(slot->pr_isolation_unfreeze, map);
+
+	iounmap(map);
+	return err;
+}
+
+/*
+ * Load the bitstream. For PR platform load the partial bitstream and for FLAT
+ * platform load the full bitstream.
+ *
+ * @param       zdev:   zocl device structure
+ * @param       buffer: xclbin data buffer pointer
+ * @param       length: xclbin data buffer size
+ * @param       slot: Target slot structure
+ *
+ * @return      0 on success, Error code on failure.
+ */
+static int
+zocl_load_bitstream(struct drm_zocl_dev *zdev, char *buffer, int length,
+		   struct drm_zocl_slot *slot)
+{
+	struct XHwIcap_Bit_Header bit_header = { 0 };
+	char *data = NULL;
+	size_t i;
+
+	memset(&bit_header, 0, sizeof(bit_header));
+	if (xrt_xclbin_parse_header(buffer, DMA_HWICAP_BITFILE_BUFFER_SIZE,
+	    &bit_header)) {
+		DRM_ERROR("bitstream header parse failed");
+		return -EINVAL;
+	}
+
+	if ((bit_header.HeaderLength + bit_header.BitstreamLength) > length) {
+		DRM_ERROR("bitstream header+stream length parse failed");
+		return -EINVAL;
+	}
+
+	/*
+	 * Swap bytes to big endian
+	 */
+	data = buffer + bit_header.HeaderLength;
+	for (i = 0; i < (bit_header.BitstreamLength / 4) ; ++i)
+		cpu_to_be32s((u32*)(data) + i);
+
+	/* On pr platofrm load partial bitstream and on Flat platform load full bitstream */
+	if (slot->pr_isolation_addr)
+		return zocl_load_partial(zdev, data, bit_header.BitstreamLength, slot);
+	/* 0 is for full bitstream */
+	return zocl_fpga_mgr_load(zdev, buffer, length, 0);
+}
+
+static int
+zocl_load_pskernel(struct drm_zocl_dev *zdev, struct axlf *axlf)
+{
+	struct axlf_section_header *header = NULL;
+	char *xclbin = (char *)axlf;
+	struct soft_krnl *sk = zdev->soft_kernel;
+	int count, sec_idx = 0, scu_idx = 0;
+	int i, ret;
+
+	if (!sk) {
+		DRM_ERROR("%s Failed: no softkernel support\n", __func__);
+		return -ENODEV;
+	}
+
+	mutex_lock(&sk->sk_lock);
+	if(!IS_ERR(&sk->sk_meta_bo)) {
+		zocl_drm_free_bo(sk->sk_meta_bo);
+	}
+	for (i = 0; i < sk->sk_nimg; i++) {
+		if (IS_ERR(&sk->sk_img[i].si_bo))
+			continue;
+		zocl_drm_free_bo(sk->sk_img[i].si_bo);
+	}
+	kfree(sk->sk_img);
+	sk->sk_nimg = 0;
+	sk->sk_img = NULL;
+
+	count = xrt_xclbin_get_section_num(axlf, SOFT_KERNEL);
+	if (count == 0) {
+		mutex_unlock(&sk->sk_lock);
+		return 0;
+	}
+
+
+	sk->sk_nimg = count;
+	sk->sk_img = kzalloc(sizeof(struct scu_image) * count, GFP_KERNEL);
+	header = xrt_xclbin_get_section_hdr_next(axlf, EMBEDDED_METADATA, header);
+	if(header) {
+		DRM_INFO("Found EMBEDDED_METADATA section\n");
+	} else {
+		DRM_ERROR("EMBEDDED_METADATA section not found!\n");
+		mutex_unlock(&sk->sk_lock);
+		return -EINVAL;
+	}
+	sk->sk_meta_bo = zocl_drm_create_bo(zdev->ddev, header->m_sectionSize,
+					    ZOCL_BO_FLAGS_CMA);
+	if (IS_ERR(sk->sk_meta_bo)) {
+		ret = PTR_ERR(sk->sk_meta_bo);
+		DRM_ERROR("Failed to allocate BO: %d\n", ret);
+		mutex_unlock(&sk->sk_lock);
+		return ret;
+	}
+
+	sk->sk_meta_bo->flags = ZOCL_BO_FLAGS_CMA;
+	sk->sk_meta_bohdl = -1;
+	DRM_INFO("Caching EMBEDDED_METADATA\n");
+	memcpy(sk->sk_meta_bo->cma_base.vaddr, xclbin + header->m_sectionOffset,
+	       header->m_sectionSize);
+
+	header = xrt_xclbin_get_section_hdr_next(axlf, SOFT_KERNEL, header);
+	while (header) {
+		struct soft_kernel *sp =
+		    (struct soft_kernel *)&xclbin[header->m_sectionOffset];
+		char *begin = (char *)sp;
+		struct scu_image *sip = &sk->sk_img[sec_idx++];
+
+		DRM_INFO("Found soft kernel %d\n",sec_idx);
+		sip->si_start = scu_idx;
+		sip->si_end = scu_idx + sp->m_num_instances - 1;
+		if (sip->si_end >= MAX_SOFT_KERNEL) {
+			DRM_ERROR("PS CU number exceeds %d\n", MAX_SOFT_KERNEL);
+			mutex_unlock(&sk->sk_lock);
+			return -EINVAL;
+		}
+
+		sip->si_bo = zocl_drm_create_bo(zdev->ddev, sp->m_image_size,
+		    ZOCL_BO_FLAGS_CMA);
+		if (IS_ERR(sip->si_bo)) {
+			ret = PTR_ERR(sip->si_bo);
+			DRM_ERROR("Failed to allocate BO: %d\n", ret);
+			mutex_unlock(&sk->sk_lock);
+			return ret;
+		}
+
+		sip->si_bo->flags = ZOCL_BO_FLAGS_CMA;
+		sip->si_bohdl = -1;
+		memcpy(sip->si_bo->cma_base.vaddr, begin + sp->m_image_offset,
+		    sp->m_image_size);
+
+		strncpy(sip->scu_name,
+		    begin + sp->mpo_symbol_name,
+		    PS_KERNEL_NAME_LENGTH - 1);
+		scu_idx += sp->m_num_instances;
+
+		header = xrt_xclbin_get_section_hdr_next(axlf, SOFT_KERNEL,
+		    header);
+	}
+
+	mutex_unlock(&sk->sk_lock);
+
+	return 0;
+}
+
+static int
+zocl_offsetof_sect(enum axlf_section_kind kind, void *sect,
+		struct axlf *axlf_full, char __user *xclbin_ptr)
+{
+	uint64_t offset;
+	uint64_t size;
+	void **sect_tmp = (void *)sect;
+	int err = 0;
+
+	err = xrt_xclbin_section_info(axlf_full, kind, &offset, &size);
+	if (err) {
+		DRM_WARN("get section %s err: %d ",
+		    xrt_xclbin_kind_to_string(kind), err);
+		return 0;
+	}
+
+	*sect_tmp = &xclbin_ptr[offset];
+
+	return size;
+}
+
+/* zocl_read_sect will alloc memory for sect, callers will call vfree */
+static int
+zocl_read_sect(enum axlf_section_kind kind, void *sect,
+		struct axlf *axlf_full, char __user *xclbin_ptr)
+{
+	uint64_t offset;
+	uint64_t size;
+	void **sect_tmp = (void *)sect;
+	int err = 0;
+
+	err = xrt_xclbin_section_info(axlf_full, kind, &offset, &size);
+	if (err) {
+		DRM_INFO("skip kind %d(%s) return code: %d", kind,
+		    xrt_xclbin_kind_to_string(kind), err);
+		return 0;
+	} else {
+		DRM_INFO("found kind %d(%s)", kind,
+		    xrt_xclbin_kind_to_string(kind));
+	}
+
+	*sect_tmp = vmalloc(size);
+	err = copy_from_user(*sect_tmp, &xclbin_ptr[offset], size);
+	if (err) {
+		DRM_WARN("copy_from_user for section %s err: %d ",
+		    xrt_xclbin_kind_to_string(kind), err);
+		vfree(*sect_tmp);
+		sect = NULL;
+		return 0;
+	}
+
+	return size;
+}
+
+/* Read XCLBIN sections in kernel space */
+/* zocl_read_sect will alloc memory for sect, callers will call vfree */
+static int
+zocl_read_sect_kernel(enum axlf_section_kind kind, void *sect,
+		      struct axlf *axlf_full, char *xclbin_ptr)
+{
+	uint64_t offset = 0;
+	uint64_t size = 0;
+	void **sect_tmp = (void *)sect;
+	int err = 0;
+
+	err = xrt_xclbin_section_info(axlf_full, kind, &offset, &size);
+	if (err) {
+		DRM_INFO("skip kind %d(%s) return code: %d", kind,
+		    xrt_xclbin_kind_to_string(kind), err);
+		return 0;
+	} else {
+		DRM_INFO("found kind %d(%s)", kind,
+		    xrt_xclbin_kind_to_string(kind));
+	}
+
+	*sect_tmp = vmalloc(size);
+	memcpy(*sect_tmp, &xclbin_ptr[offset], size);
+
+	return size;
+}
+
+static inline u32 xclbin_protocol(u32 prop)
+{
+	u32 intr_id = prop & IP_CONTROL_MASK;
+
+	return intr_id >> IP_CONTROL_SHIFT;
+}
+
+static inline u32 xclbin_intr_enable(u32 prop)
+{
+	u32 intr_enable = prop & IP_INT_ENABLE_MASK;
+
+	return intr_enable;
+}
+
+static inline u32 xclbin_intr_id(u32 prop)
+{
+	u32 intr_id = prop & IP_INTERRUPT_ID_MASK;
+
+	return intr_id >> IP_INTERRUPT_ID_SHIFT;
+}
+
+/*
+ * Get the next free aparture index. If phy_addr is zero of an index then
+ * consider it as free index.
+ *
+ * @param       zdev:    zocl device structure
+ *
+ * @return      valid index on success, Error code on failure.
+ */
+static int
+get_next_free_apt_index(struct drm_zocl_dev *zdev)
+{
+	int apt_idx = 0;
+
+	for (apt_idx = 0; apt_idx < MAX_APT_NUM; ++apt_idx) {
+		if (zdev->apertures[apt_idx].addr == EMPTY_APT_VALUE)
+			return apt_idx;
+	}
+
+	return -ENOSPC;
+}
+
+/*
+ * Always keep tract of max aperture index. This will help not to traverse
+ * maximum size of the aperture number always.
+ *
+ * @param       zdev:    zocl device structure
+ *
+ */
+static void
+update_max_apt_number(struct drm_zocl_dev *zdev)
+{
+	int apt_idx = 0;
+
+	zdev->num_apts = 0;
+	for (apt_idx = 0; apt_idx < MAX_APT_NUM; ++apt_idx) {
+		if (zdev->apertures[apt_idx].addr != 0)
+			zdev->num_apts = apt_idx + 1;
+	}
+}
+
+/*
+ * Cleanup the apertures of a specific slot. Others will remain same without
+ * changing the index.
+ *
+ * @param       zdev:		zocl device structure
+ * @param       slot_idx:	Specific slot index
+ *
+ */
+static void
+zocl_clean_aperture(struct drm_zocl_dev *zdev, u32 slot_idx)
+{
+	int apt_idx = 0;
+	struct addr_aperture *apt = NULL;
+
+	for (apt_idx = 0; apt_idx < MAX_APT_NUM; ++apt_idx) {
+		apt = &zdev->apertures[apt_idx];
+		if (apt->slot_idx == slot_idx) {
+			/* Reset this aperture index */
+			apt->addr = EMPTY_APT_VALUE;
+			apt->size = 0;
+			apt->prop = 0;
+			apt->cu_idx = -1;
+			apt->slot_idx = 0xFFFF;
+		}
+	}
+
+	update_max_apt_number(zdev);
+}
+
+/* Record all of the hardware address apertures in the XCLBIN
+ * This could be used to verify if the configure command set wrong CU base
+ * address and allow user map one of the aperture to user space.
+ *
+ * The xclbin doesn't contain IP size. Use hardcoding size for now.
+ *
+ * @param       zdev:	zocl device structure
+ * @param       slot:	Specific slot staructure
+ *
+ * @return      0 on success, Error code on failure.
+ */
+static int
+zocl_update_apertures(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot)
+{
+	struct ip_data *ip = NULL;
+	struct debug_ip_data *dbg_ip = NULL;
+	struct addr_aperture *apt = NULL;
+	int total = 0;
+	int apt_idx = 0;
+	int i = 0;
+
+	/* Update aperture should only happen when loading xclbin */
+	if (slot->ip)
+		total += slot->ip->m_count;
+
+	if (slot->debug_ip)
+		total += slot->debug_ip->m_count;
+
+	if (total == 0)
+		return 0;
+
+	/* If this happened, the xclbin is super bad */
+	if ((total < 0) || (total > MAX_APT_NUM)) {
+		DRM_ERROR("Invalid number of apertures\n");
+		return -EINVAL;
+	}
+
+	/* Cleanup the aperture for this slot before update for new xclbin */
+	zocl_clean_aperture(zdev, slot->slot_idx);
+
+	/* Now update the aperture for the new xclbin */
+	if (slot->ip) {
+		for (i = 0; i < slot->ip->m_count; ++i) {
+			ip = &slot->ip->m_ip_data[i];
+			apt_idx = get_next_free_apt_index(zdev);
+			if (apt_idx < 0) {
+				DRM_ERROR("No more free apertures\n");
+				return -EINVAL;
+			}
+			apt = &zdev->apertures[apt_idx];
+
+			apt->addr = ip->m_base_address;
+			apt->size = CU_SIZE;
+			apt->prop = ip->properties;
+			apt->cu_idx = -1;
+			apt->slot_idx = slot->slot_idx;
+		}
+		/* Update num_apts based on current index */
+		update_max_apt_number(zdev);
+	}
+
+	if (slot->debug_ip) {
+		for (i = 0; i < slot->debug_ip->m_count; ++i) {
+			dbg_ip = &slot->debug_ip->m_debug_ip_data[i];
+			apt_idx = get_next_free_apt_index(zdev);
+			if (apt_idx < 0) {
+				DRM_ERROR("No more free apertures\n");
+				return -EINVAL;
+			}
+			apt = &zdev->apertures[apt_idx];
+
+			apt->addr = dbg_ip->m_base_address;
+			apt->slot_idx = slot->slot_idx;
+			if (dbg_ip->m_type == AXI_MONITOR_FIFO_LITE
+			    || dbg_ip->m_type == AXI_MONITOR_FIFO_FULL)
+				/* FIFO_LITE has 4KB and FIFO FULL has 8KB
+				 * address range. Use both 8K is okay.
+				 */
+				apt->size = _8KB;
+			else
+				/* Others debug IPs have 64KB address range*/
+				apt->size = _64KB;
+		}
+		/* Update num_apts based on current index */
+		update_max_apt_number(zdev);
+	}
+
+	return 0;
+}
+
+/*
+ * Get the next free CU index. If cu platform device is NULL of an index then
+ * consider it as free index.
+ *
+ * @param       zdev:    zocl device structure
+ *
+ * @return      valid index on success, Error code on failure.
+ */
+static int
+zocl_get_cu_inst_idx(struct drm_zocl_dev *zdev)
+{
+	int i = 0;
+
+	/* TODO : Didn't think about efficient way till now */
+	for (i = 0; i < MAX_CU_NUM; ++i)
+		if (zdev->cu_pldev[i] == NULL)
+			return i;
+
+	return -ENOSPC;
+}
+
+/*
+ * Destroy all the CUs belongs to a specific slot. All the other CUs remain
+ * same. There could be possibility of holes in the lists. But we should not
+ * change the index of existing CUs
+ *
+ * @param       zdev:		zocl device structure
+ * @param       slot_idx:	Specific slot index
+ *
+ */
+static void
+zocl_destroy_cu_slot(struct drm_zocl_dev *zdev, u32 slot_idx)
+{
+	struct platform_device *pldev = NULL;
+	struct xrt_cu_info *info = NULL;
+	int i = 0;
+
+	for (i = 0; i < MAX_CU_NUM; ++i) {
+		pldev = zdev->cu_pldev[i];
+		if (!pldev)
+			continue;
+
+		info = dev_get_platdata(&pldev->dev);
+		if (info->slot_idx == slot_idx) {
+			/* Remove the platform-level device */
+			platform_device_del(pldev);
+			/* Destroy the platform device */
+			platform_device_put(pldev);
+			zdev->cu_pldev[i] = NULL;
+		}
+	}
+}
+
+/*
+ * Create the CUs for a specific slot. CUs for a specific slot may not be
+ * contigious. CU index will be assign based on the next free index.
+ *
+ * @param       zdev:	zocl device structure
+ * @param       slot: Specific slot structure
+ *
+ * @return      0 on success, Error code on failure.
+ */
+static int
+zocl_create_cu(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot)
+{
+	int err = 0;
+	int i = 0;
+	int num_cus = 0;
+	struct xrt_cu_info *cu_info = NULL;
+	struct kernel_info *krnl_info = NULL;
+
+	if (!slot->ip)
+		return 0;
+
+	cu_info = kzalloc(MAX_CUS * sizeof(struct xrt_cu_info), GFP_KERNEL);
+	if (!cu_info)
+		return -ENOMEM;
+
+	num_cus = kds_ip_layout2cu_info(slot->ip, cu_info, MAX_CUS);
+
+	for (i = 0; i < num_cus; ++i) {
+
+		/* Skip streaming kernel */
+		if (cu_info[i].addr == -1)
+			continue;
+
+		cu_info[i].slot_idx = slot->slot_idx;
+		cu_info[i].num_res = 1;
+
+		switch (cu_info[i].protocol) {
+		case CTRL_HS:
+		case CTRL_CHAIN:
+		case CTRL_NONE:
+			cu_info[i].model = XCU_HLS;
+			break;
+		case CTRL_FA:
+			cu_info[i].model = XCU_FA;
+			break;
+		default:
+			kfree(cu_info);
+			return -EINVAL;
+		}
+
+		/* Get the next free CU index */
+		cu_info[i].inst_idx = zocl_get_cu_inst_idx(zdev);
+		/* ip_data->m_name format "<kernel name>:<instance name>",
+		 * where instance name is so called CU name.
+		 */
+		krnl_info = zocl_query_kernel(slot, cu_info[i].kname);
+		if (!krnl_info) {
+			DRM_WARN("%s CU has no metadata, using default",cu_info[i].kname);
+			cu_info[i].args = NULL;
+			cu_info[i].num_args = 0;
+			cu_info[i].size = 0x10000;
+		} else {
+			cu_info[i].args = (struct xrt_cu_arg *)&krnl_info->args[i];
+			cu_info[i].num_args = krnl_info->anums;
+			cu_info[i].size = krnl_info->range;
+
+			if (krnl_info->features & KRNL_SW_RESET)
+				cu_info[i].sw_reset = true;
+		}
+
+		/* CU sub device is a virtual device, which means there is no
+		 * device tree nodes
+		 */
+		err = subdev_create_cu(zdev->ddev->dev, &cu_info[i], &zdev->cu_pldev[i]);
+		if (err) {
+			DRM_ERROR("cannot create CU subdev");
+			goto err;
+		}
+	}
+	kfree(cu_info);
+
+	return 0;
+err:
+	zocl_destroy_cu_slot(zdev, slot->slot_idx);
+	return err;
+}
+
+static inline bool
+zocl_xclbin_same_uuid(struct drm_zocl_slot *slot, xuid_t *uuid)
+{
+	return (zocl_xclbin_get_uuid(slot) != NULL &&
+	    uuid_equal(uuid, zocl_xclbin_get_uuid(slot)));
+}
+
+/*
+ * Return the slot pointer for the given xclbin uuid as an Input.
+ *
+ * @param       zdev:	zocl device structure
+ * @param       id:	xclbin uuid
+ *
+ * @return      domian pointer on success, NULL on failure.
+ */
+struct drm_zocl_slot *
+zocl_get_slot(struct drm_zocl_dev *zdev, uuid_t *id)
+{
+	struct drm_zocl_slot *zocl_slot = NULL;
+	int i = 0;
+
+	for (i = 0; i < zdev->num_pr_slot; i++) {
+		zocl_slot = zdev->pr_slot[i];
+		if (zocl_slot) {
+			mutex_lock(&zocl_slot->slot_xclbin_lock);
+			if (zocl_xclbin_same_uuid(zocl_slot, id)) {
+				mutex_unlock(&zocl_slot->slot_xclbin_lock);
+				return zocl_slot;
+			}
+			mutex_unlock(&zocl_slot->slot_xclbin_lock);
+		}
+	}
+
+	return NULL;
+}
+
+/*
+ * Cache the xclbin blob so that it can be shared by processes.
+ *
+ * Note: currently, we only cache xclbin blob for AIE only xclbin to
+ *       support AIE multi-processes. For AIE only xclbin, we load
+ *       the PDI to AIE even it has been loaded. But if a process is
+ *       using UUID to load xclbin metatdata, we don't load PDI to AIE.
+ *       So that a shared AIE context can load AIE metadata without
+ *       reload the hardware and can do non-destructive operations.
+ */
+static int
+zocl_cache_xclbin(struct drm_zocl_slot *slot, struct axlf *axlf,
+		char __user *xclbin_ptr)
+{
+	int ret = 0;
+	size_t size = axlf->m_header.m_length;
+
+	slot->axlf = vmalloc(size);
+	if (!slot->axlf)
+		return -ENOMEM;
+
+	ret = copy_from_user(slot->axlf, xclbin_ptr, size);
+	if (ret) {
+		vfree(slot->axlf);
+		return ret;
+	}
+
+	slot->axlf_size = size;
+
+	return 0;
+}
+
+/*
+ * Cache the xclbin blob so that it can be shared by processes.
+ *
+ * Note: currently, we only cache xclbin blob for AIE only xclbin to
+ *       support AIE multi-processes. For AIE only xclbin, we load
+ *       the PDI to AIE even it has been loaded. But if a process is
+ *       using UUID to load xclbin metatdata, we don't load PDI to AIE.
+ *       So that a shared AIE context can load AIE metadata without
+ *       reload the hardware and can do non-destructive operations.
+ */
+static int
+zocl_kernel_cache_xclbin(struct drm_zocl_slot *slot, struct axlf *axlf,
+		char *xclbin_ptr)
+{
+	size_t size = axlf->m_header.m_length;
+
+	slot->axlf = vmalloc(size);
+	if (!slot->axlf) {
+		DRM_ERROR("%s cannot allocate slot->axlf memory!",__func__);
+		return -ENOMEM;
+	}
+
+	memcpy(slot->axlf, xclbin_ptr, size);
+
+	slot->axlf_size = size;
+
+	return 0;
+}
+
+/*
+ * This function takes an XCLBIN in kernel buffer and extracts
+ * BITSTREAM_PDI section (or PDI section). Then load the extracted
+ * section through fpga manager.
+ *
+ * Note: this is only used under ert mode so that we do not need to
+ * check context or cache XCLBIN metadata, which are done by host
+ * XRT driver. Only if the same XCLBIN has been loaded, we skip loading.
+ *
+ * @param       zdev:   zocl device structure
+ * @param       data:   xclbin buffer
+ * @param       slot: Specific slot structure
+ *
+ * @return      0 on success, Error code on failure.
+ */
+int
+zocl_xclbin_load_pdi(struct drm_zocl_dev *zdev, void *data,
+                    struct drm_zocl_slot *slot)
+{
+        struct axlf *axlf = data;
+        struct axlf *axlf_head = axlf;
+        char *xclbin = NULL;
+        char *section_buffer = NULL;
+        size_t size_of_header = 0;
+        size_t num_of_sections = 0;
+        uint64_t size = 0;
+        int ret = 0;
+        int count = 0;
+
+        if (memcmp(axlf_head->m_magic, "xclbin2", 8)) {
+                DRM_INFO("Invalid xclbin magic string");
+                return -EINVAL;
+        }
+
+        mutex_lock(&slot->slot_xclbin_lock);
+	/* Check unique ID */
+	if (zocl_xclbin_same_uuid(slot, &axlf_head->m_header.uuid)) {
+		DRM_INFO("%s The XCLBIN already loaded, uuid: %pUb",
+			 __func__, &axlf_head->m_header.uuid);
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return ret;
+	}
+
+	write_lock(&zdev->attr_rwlock);
+
+	/* Get full axlf header */
+	size_of_header = sizeof(struct axlf_section_header);
+	num_of_sections = axlf_head->m_header.m_numSections-1;
+	xclbin = (char __user *)axlf;
+	ret =
+	    !ZOCL_ACCESS_OK(VERIFY_READ, xclbin, axlf_head->m_header.m_length);
+	if (ret) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	size = zocl_offsetof_sect(BITSTREAM_PARTIAL_PDI, &section_buffer,
+	    axlf, xclbin);
+	if (size > 0) {
+		write_unlock(&zdev->attr_rwlock);
+		ret = zocl_load_partial(zdev, section_buffer, size, slot);
+		write_lock(&zdev->attr_rwlock);
+		if (ret)
+			goto out;
+	}
+
+	size = zocl_offsetof_sect(PDI, &section_buffer, axlf, xclbin);
+	if (size > 0) {
+		write_unlock(&zdev->attr_rwlock);
+		ret = zocl_load_partial(zdev, section_buffer, size, slot);
+		write_lock(&zdev->attr_rwlock);
+		if (ret)
+			goto out;
+	}
+
+	count = xrt_xclbin_get_section_num(axlf, SOFT_KERNEL);
+	if (count > 0) {
+		ret = zocl_cache_xclbin(slot, axlf, xclbin);
+		if (ret) {
+			DRM_ERROR("%s cannot cache xclbin",__func__);
+			goto out;
+		}
+		ret = zocl_load_pskernel(zdev, slot->axlf);
+		if (ret)
+			goto out;
+	}
+
+	/* preserve uuid, avoid double download */
+	zocl_xclbin_set_uuid(slot, &axlf_head->m_header.uuid);
+
+	/* no need to reset scheduler, config will always reset scheduler */
+
+out:
+	write_unlock(&zdev->attr_rwlock);
+	DRM_INFO("%s %pUb ret: %d", __func__, zocl_xclbin_get_uuid(slot),
+		ret);
+	mutex_unlock(&slot->slot_xclbin_lock);
+	return ret;
+}
+
+/*
+ * This function takes an XCLBIN in kernel buffer and extracts
+ * SOFT_KERNEL section.
+ *
+ * If the same XCLBIN has been loaded, we skip loading.
+ *
+ * @param       zdev:   zocl device structure
+ * @param       data:   xclbin buffer
+ *
+ * @return      0 on success, Error code on failure.
+ */
+int
+zocl_xclbin_load_pskernel(struct drm_zocl_dev *zdev, void *data)
+{
+        struct axlf *axlf = (struct axlf *)data;
+        struct axlf *axlf_head = axlf;
+	struct drm_zocl_slot *slot;
+        char *xclbin = NULL;
+        size_t size_of_header = 0;
+        size_t num_of_sections = 0;
+        int ret = 0;
+        int count = 0;
+	void *aie_res = 0;
+
+        if (memcmp(axlf_head->m_magic, "xclbin2", 8)) {
+                DRM_INFO("Invalid xclbin magic string");
+                return -EINVAL;
+        }
+
+	// Currently only 1 slot - TODO: Support multi-slot in the future
+	slot = zdev->pr_slot[0];
+	
+        mutex_lock(&slot->slot_xclbin_lock);
+	/* Check unique ID */
+	if (zocl_xclbin_same_uuid(slot, &axlf_head->m_header.uuid)) {
+		DRM_INFO("%s The XCLBIN already loaded, uuid: %pUb",
+			 __func__, &axlf_head->m_header.uuid);
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return ret;
+	}
+
+	write_lock(&zdev->attr_rwlock);
+
+	/* Get full axlf header */
+	size_of_header = sizeof(struct axlf_section_header);
+	num_of_sections = axlf_head->m_header.m_numSections-1;
+	xclbin = (char *)axlf;
+	if (zocl_xclbin_get_uuid(slot) != NULL) {
+		if (zdev->aie) {
+			/*
+			 * Dont reset if aie is already in reset
+			 * state
+			 */
+			if( !zdev->aie->aie_reset) {
+				ret = zocl_aie_reset(zdev);
+				if (ret)
+					goto out;
+			}
+			zocl_destroy_aie(zdev);
+		}
+	}
+	
+	/*
+	 * Read AIE_RESOURCES section. aie_res will be NULL if there is no
+	 * such a section.
+	 */
+	zocl_read_sect_kernel(AIE_RESOURCES, &aie_res, axlf, xclbin);
+
+	// Cache full xclbin
+	write_unlock(&zdev->attr_rwlock);
+	//last argument represents aie generation. 1. aie, 2. aie-ml ...
+	zocl_create_aie(zdev, axlf, aie_res,1);
+	write_lock(&zdev->attr_rwlock);
+
+	count = xrt_xclbin_get_section_num(axlf, SOFT_KERNEL);
+	if (count > 0) {
+		ret = zocl_kernel_cache_xclbin(slot, axlf, xclbin);
+		if (ret) {
+			DRM_ERROR("%s cannot cache xclbin",__func__);
+			goto out;
+		}
+		ret = zocl_load_pskernel(zdev, slot->axlf);
+		if (ret)
+			goto out;
+	}
+
+	/* preserve uuid, avoid double download */
+	zocl_xclbin_set_uuid(slot, &axlf_head->m_header.uuid);
+
+	/* no need to reset scheduler, config will always reset scheduler */
+
+out:
+	write_unlock(&zdev->attr_rwlock);
+	vfree(aie_res);
+	if (!ret)
+		DRM_INFO("%s %pUb ret: %d", __func__, zocl_xclbin_get_uuid(slot), ret);
+	else
+		DRM_INFO("%s ret: %d", __func__, ret);
+	mutex_unlock(&slot->slot_xclbin_lock);
+	return ret;
+}
+
+static int
+zocl_load_aie_only_pdi(struct drm_zocl_dev *zdev, struct axlf *axlf,
+			char __user *xclbin, struct sched_client_ctx *client)
+{
+	uint64_t size = 0;
+	char *pdi_buf = NULL;
+	int ret = 0;
+
+	if (client && client->aie_ctx == ZOCL_CTX_SHARED) {
+		DRM_ERROR("%s Shared context can not load xclbin", __func__);
+		return -EPERM;
+	}
+
+	size = zocl_read_sect(PDI, &pdi_buf, axlf, xclbin);
+	if (size == 0)
+		return 0;
+
+	ret = zocl_fpga_mgr_load(zdev, pdi_buf, size, FPGA_MGR_PARTIAL_RECONFIG);
+	vfree(pdi_buf);
+
+	/* Mark AIE out of reset state after load PDI */
+	if (zdev->aie) {
+		mutex_lock(&zdev->aie_lock);
+		zdev->aie->aie_reset = false;
+		mutex_unlock(&zdev->aie_lock);
+	}
+
+	return ret;
+}
+
+/*
+ * Free the xclbin specific sections for this slot.
+ *
+ * @param       slot: Specific slot structure
+ *
+ */
+void zocl_free_sections(struct drm_zocl_slot *slot)
+{
+	if (slot->ip) {
+		vfree(slot->ip);
+		CLEAR(slot->ip);
+	}
+	if (slot->debug_ip) {
+		vfree(slot->debug_ip);
+		CLEAR(slot->debug_ip);
+	}
+	if (slot->connectivity) {
+		vfree(slot->connectivity);
+		CLEAR(slot->connectivity);
+	}
+	if (slot->topology) {
+		vfree(slot->topology);
+		CLEAR(slot->topology);
+	}
+	if (slot->axlf) {
+		vfree(slot->axlf);
+		CLEAR(slot->axlf);
+		slot->axlf_size = 0;
+	}
+}
+
+/*
+ * Load a bitstream, partial metadata or PDI to the FPGA from userspace pointer.
+ *
+ * @param       zdev:		zocl device structure
+ * @param       axlf:		xclbin userspace header pointer
+ * @param       xclbin:		xclbin userspace buffer pointer
+ * @param       kind:		xclbin section type
+ * @param       slot:		Specific slot structure
+ *
+ * @return      0 on success, Error code on failure.
+ *
+ */
+static int
+zocl_load_sect(struct drm_zocl_dev *zdev, struct axlf *axlf, char __user *xclbin,
+	      enum axlf_section_kind kind, struct drm_zocl_slot *slot)
+{
+	uint64_t size = 0;
+	char *section_buffer = NULL;
+	int ret = 0;
+
+	size = zocl_read_sect(kind, &section_buffer, axlf, xclbin);
+	if (size == 0)
+		return 0;
+
+	switch (kind) {
+	case BITSTREAM:
+		ret = zocl_load_bitstream(zdev, section_buffer, size, slot);
+		break;
+	case PDI:
+	case BITSTREAM_PARTIAL_PDI:
+		ret = zocl_load_partial(zdev, section_buffer, size, slot);
+		break;
+#if KERNEL_VERSION(5, 4, 0) <= LINUX_VERSION_CODE
+	case PARTITION_METADATA: {
+		int id = -1, err = 0;
+		char *bsection_buffer = NULL;
+		char *vaddr = NULL;
+		struct drm_zocl_bo *bo;
+		uint64_t bsize = 0;
+		uint64_t flags = 0;
+		if (slot->partial_overlay_id != -1 &&
+			axlf->m_header.m_mode == XCLBIN_PR) {
+			err = of_overlay_remove(&slot->partial_overlay_id);
+			if (err < 0) {
+				DRM_WARN("Failed to delete rm overlay (err=%d)\n", err);
+				ret = err;
+				break;
+			}
+			slot->partial_overlay_id = -1;
+		} else if (zdev->full_overlay_id != -1 &&
+			   axlf->m_header.m_mode == XCLBIN_FLAT) {
+			err = of_overlay_remove_all();
+			if (err < 0) {
+				DRM_WARN("Failed to delete static overlay (err=%d)\n", err);
+				ret = err;
+				break;
+			}
+			slot->partial_overlay_id = -1;
+			zdev->full_overlay_id = -1;
+		}
+
+		bsize = zocl_read_sect(BITSTREAM, &bsection_buffer, axlf,
+				       xclbin);
+		if (bsize == 0) {
+			ret = 0;
+			break;
+		}
+
+		bo = zocl_drm_create_bo(zdev->ddev, bsize, ZOCL_BO_FLAGS_CMA);
+		if (IS_ERR(bo)) {
+			vfree(bsection_buffer);
+			ret = PTR_ERR(bo);
+			break;
+		}
+		vaddr = bo->cma_base.vaddr;
+		memcpy(vaddr,bsection_buffer,bsize);
+
+		flags = zdev->fpga_mgr->flags;
+		zdev->fpga_mgr->flags |= FPGA_MGR_CONFIG_DMA_BUF;
+		zdev->fpga_mgr->dmabuf = drm_gem_prime_export(&bo->gem_base, 0);
+		err = of_overlay_fdt_apply((void *)section_buffer, size, &id);
+		if (err < 0) {
+			DRM_WARN("Failed to create overlay (err=%d)\n", err);
+			zdev->fpga_mgr->flags = flags;
+			zdev->fpga_mgr->dmabuf = NULL;
+			zocl_drm_free_bo(bo);
+			vfree(bsection_buffer);
+			ret = err;
+			break;
+		}
+
+		if (axlf->m_header.m_mode == XCLBIN_PR)
+			slot->partial_overlay_id = id;
+		else
+			zdev->full_overlay_id = id;
+
+		/* Restore the flags */
+		zdev->fpga_mgr->flags = flags;
+		zdev->fpga_mgr->dmabuf = NULL;
+		zocl_drm_free_bo(bo);
+		vfree(bsection_buffer);
+		break;
+		}
+#endif
+	default:
+		DRM_WARN("Unsupported load type %d", kind);
+	}
+
+	vfree(section_buffer);
+
+	return ret;
+}
+
+static bool
+is_aie_only(struct axlf *axlf)
+{
+	return (axlf->m_header.m_actionMask & AM_LOAD_AIE);
+}
+
+int
+zocl_xclbin_refcount(struct drm_zocl_slot *slot)
+{
+	BUG_ON(!mutex_is_locked(&slot->slot_xclbin_lock));
+
+	return slot->slot_xclbin->zx_refcnt;
+}
+
+/*
+ * This function is the main entry point to load xclbin. It's takes an userspace
+ * pointer of xclbin and copy the xclbin data to kernel space. Then load that
+ * xclbin to the FPGA. It also initialize other modules like, memory, aie, CUs
+ * etc.
+ *
+ * @param       zdev:		zocl device structure
+ * @param       axlf_obj:	xclbin userspace structure
+ * @param       client:		user space client attached to device
+ *
+ * @return      0 on success, Error code on failure.
+ */
+int
+zocl_xclbin_read_axlf(struct drm_zocl_dev *zdev, struct drm_zocl_axlf *axlf_obj,
+	struct sched_client_ctx *client)
+{
+	struct axlf axlf_head;
+	struct axlf *axlf = NULL;
+	long axlf_size;
+	char __user *xclbin = NULL;
+	size_t size_of_header;
+	size_t num_of_sections;
+	void *kernels;
+	void *aie_res = 0;
+	uint64_t size = 0;
+	int ret = 0;
+	struct drm_zocl_slot *slot = NULL;
+	int slot_id = axlf_obj->za_slot_id;
+	uint8_t hw_gen = axlf_obj->hw_gen;
+
+	if (slot_id > zdev->num_pr_slot) {
+		DRM_ERROR("Invalid Slot[%d]", slot_id);
+		return -EINVAL;
+	}
+
+	slot = zdev->pr_slot[slot_id];
+	if (!slot) {
+		DRM_ERROR("Slot[%d] doesn't exists", slot_id);
+		return -EINVAL;
+	}
+
+	mutex_lock(&slot->slot_xclbin_lock);
+
+	if (copy_from_user(&axlf_head, axlf_obj->za_xclbin_ptr,
+	    sizeof(struct axlf))) {
+		DRM_WARN("copy_from_user failed for za_xclbin_ptr");
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return -EFAULT;
+	}
+
+	if (memcmp(axlf_head.m_magic, "xclbin2", 8)) {
+		DRM_WARN("xclbin magic is invalid %s", axlf_head.m_magic);
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return -EINVAL;
+	}
+
+	/* Get full axlf header */
+	size_of_header = sizeof(struct axlf_section_header);
+	num_of_sections = axlf_head.m_header.m_numSections - 1;
+	axlf_size = sizeof(struct axlf) + size_of_header * num_of_sections;
+	axlf = vmalloc(axlf_size);
+	if (!axlf) {
+		DRM_WARN("read xclbin fails: no memory");
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return -ENOMEM;
+	}
+
+	if (copy_from_user(axlf, axlf_obj->za_xclbin_ptr, axlf_size)) {
+		DRM_WARN("read xclbin: fail copy from user memory");
+		vfree(axlf);
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return -EFAULT;
+	}
+
+	xclbin = (char __user *)axlf_obj->za_xclbin_ptr;
+	ret = !ZOCL_ACCESS_OK(VERIFY_READ, xclbin, axlf_head.m_header.m_length);
+	if (ret) {
+		DRM_WARN("read xclbin: fail the access check");
+		vfree(axlf);
+		mutex_unlock(&slot->slot_xclbin_lock);
+		return -EFAULT;
+	}
+
+	/* After this lock till unlock is an atomic context */
+	write_lock(&zdev->attr_rwlock);
+
+	/*
+	 * Read AIE_RESOURCES section. aie_res will be NULL if there is no
+	 * such a section.
+	 */
+	zocl_read_sect(AIE_RESOURCES, &aie_res, axlf, xclbin);
+
+	/* Check unique ID */
+	if (zocl_xclbin_same_uuid(slot, &axlf_head.m_header.uuid)) {
+		if (!(axlf_obj->za_flags & DRM_ZOCL_FORCE_PROGRAM)) {
+			if (is_aie_only(axlf)) {
+				write_unlock(&zdev->attr_rwlock);
+				ret = zocl_load_aie_only_pdi(zdev, axlf, xclbin,
+							     client);
+				write_lock(&zdev->attr_rwlock);
+				if (ret)
+					DRM_WARN("read xclbin: fail to load AIE");
+				else {
+					write_unlock(&zdev->attr_rwlock);
+					zocl_create_aie(zdev, axlf, aie_res,hw_gen);
+					write_lock(&zdev->attr_rwlock);
+					zocl_cache_xclbin(slot, axlf, xclbin);
+				}
+			} else {
+				DRM_INFO("%s The XCLBIN already loaded", __func__);
+			}
+			goto out0;
+		} else {
+			// We come here if user sets force_xclbin_program
+			// option "true" in xrt.ini under [Runtime] section
+			DRM_WARN("%s The XCLBIN already loaded. Force xclbin download", __func__);
+		}
+	}
+
+	/* 1. We locked &zdev->slot_xclbin_lock so that no new contexts
+	 * can be opened and/or closed
+	 * 2. A opened context would lock bitstream and hold it.
+	 * 3. If all contexts are closed, new kds would make sure all
+	 * relative exec BO are released
+	 */
+	if (zocl_xclbin_refcount(slot) > 0) {
+		DRM_ERROR("Current xclbin is in-use, can't change");
+		ret = -EBUSY;
+		goto out0;
+	}
+
+	/* Free sections before load the new xclbin */
+	zocl_free_sections(slot);
+
+#if KERNEL_VERSION(5, 4, 0) <= LINUX_VERSION_CODE
+	if (xrt_xclbin_get_section_num(axlf, PARTITION_METADATA) &&
+	    axlf_head.m_header.m_mode != XCLBIN_HW_EMU &&
+	    axlf_head.m_header.m_mode != XCLBIN_HW_EMU_PR) {
+		/*
+		 * Perform dtbo overlay for both static and rm region
+		 * axlf should have dtbo in PARTITION_METADATA section and
+		 * bitstream in BITSTREAM section.
+		 */
+		write_unlock(&zdev->attr_rwlock);
+		ret = zocl_load_sect(zdev, axlf, xclbin, PARTITION_METADATA,
+				    slot);
+		write_lock(&zdev->attr_rwlock);
+		if (ret)
+			goto out0;
+
+	} else
+#endif
+	if (slot->pr_isolation_addr) {
+		/* For PR support platform, device-tree has configured addr */
+		if (axlf_head.m_header.m_mode != XCLBIN_PR &&
+		    axlf_head.m_header.m_mode != XCLBIN_HW_EMU &&
+		    axlf_head.m_header.m_mode != XCLBIN_HW_EMU_PR) {
+			DRM_ERROR("xclbin m_mod %d is not a PR mode",
+			    axlf_head.m_header.m_mode);
+			ret = -EINVAL;
+			goto out0;
+		}
+
+		if (!(axlf_obj->za_flags & DRM_ZOCL_PLATFORM_PR)) {
+			DRM_INFO("disable partial bitstream download, "
+			    "axlf flags is %d", axlf_obj->za_flags);
+		} else {
+			 /*
+			  * cleanup previously loaded xclbin related data
+			  * before loading new bitstream/pdi
+			  */
+			if (zocl_xclbin_get_uuid(slot) != NULL) {
+				zocl_destroy_cu_slot(zdev, slot->slot_idx);
+				if (zdev->aie) {
+					/*
+					 * Dont reset if aie is already in reset
+					 * state
+					 */
+					if( !zdev->aie->aie_reset) {
+						ret = zocl_aie_reset(zdev);
+						if (ret)
+							goto out0;
+					}
+					zocl_destroy_aie(zdev);
+				}
+			}
+			/*
+			 * Make sure we load PL bitstream first,
+			 * if there is one, before loading AIE PDI.
+			 */
+			write_unlock(&zdev->attr_rwlock);
+			ret = zocl_load_sect(zdev, axlf, xclbin, BITSTREAM,
+					    slot);
+			write_lock(&zdev->attr_rwlock);
+			if (ret)
+				goto out0;
+
+			write_unlock(&zdev->attr_rwlock);
+			ret = zocl_load_sect(zdev, axlf, xclbin,
+			    BITSTREAM_PARTIAL_PDI, slot);
+			write_lock(&zdev->attr_rwlock);
+			if (ret)
+				goto out0;
+
+			write_unlock(&zdev->attr_rwlock);
+			ret = zocl_load_sect(zdev, axlf, xclbin, PDI, slot);
+			write_lock(&zdev->attr_rwlock);
+			if (ret)
+				goto out0;
+		}
+	} else if (is_aie_only(axlf)) {
+		write_unlock(&zdev->attr_rwlock);
+		ret = zocl_load_aie_only_pdi(zdev, axlf, xclbin, client);
+		write_lock(&zdev->attr_rwlock);
+		if (ret)
+			goto out0;
+
+		zocl_cache_xclbin(slot, axlf, xclbin);
+	} else if ((axlf_obj->za_flags & DRM_ZOCL_PLATFORM_FLAT) &&
+		   axlf_head.m_header.m_mode == XCLBIN_FLAT &&
+		   axlf_head.m_header.m_mode != XCLBIN_HW_EMU &&
+		   axlf_head.m_header.m_mode != XCLBIN_HW_EMU_PR) {
+		/*
+		 * Load full bitstream, enabled in xrt runtime config
+		 * and xclbin has full bitstream and its not hw emulation
+		 */
+		write_unlock(&zdev->attr_rwlock);
+		ret = zocl_load_sect(zdev, axlf, xclbin, BITSTREAM, slot);
+		write_lock(&zdev->attr_rwlock);
+		if (ret)
+			goto out0;
+	}
+
+	/* Populating IP_LAYOUT sections */
+	/* zocl_read_sect return size of section when successfully find it */
+	size = zocl_read_sect(IP_LAYOUT, &slot->ip, axlf, xclbin);
+	if (size <= 0) {
+		if (size != 0) {
+			ret = size;
+			goto out0;
+		}
+	} else if (sizeof_section(slot->ip, m_ip_data) != size) {
+		ret = -EINVAL;
+		goto out0;
+	}
+
+	/* Populating DEBUG_IP_LAYOUT sections */
+	size = zocl_read_sect(DEBUG_IP_LAYOUT, &slot->debug_ip, axlf, xclbin);
+	if (size <= 0) {
+		if (size != 0) {
+			ret = size;
+			goto out0;
+		}
+	} else if (sizeof_section(slot->debug_ip, m_debug_ip_data) != size) {
+		ret = -EINVAL;
+		goto out0;
+	}
+
+	ret = zocl_update_apertures(zdev, slot);
+	if (ret)
+		goto out0;
+
+	/* Kernels are slot specific. */
+	if (slot->kernels != NULL) {
+		vfree(slot->kernels);
+		slot->kernels = NULL;
+		slot->ksize = 0;
+	}
+
+	if (axlf_obj->za_ksize > 0) {
+		kernels = vmalloc(axlf_obj->za_ksize);
+		if (!kernels) {
+			ret = -ENOMEM;
+			goto out0;
+		}
+		if (copy_from_user(kernels, axlf_obj->za_kernels,
+		    axlf_obj->za_ksize)) {
+			ret = -EFAULT;
+			goto out0;
+		}
+		slot->ksize = axlf_obj->za_ksize;
+		slot->kernels = kernels;
+	}
+
+	/* Populating AIE_METADATA sections */
+	size = zocl_read_sect(AIE_METADATA, &slot->aie_data.data, axlf,
+			     xclbin);
+	if (size < 0) {
+		ret = size;
+		goto out0;
+	}
+	slot->aie_data.size = size;
+
+	/* Populating CONNECTIVITY sections */
+	size = zocl_read_sect(CONNECTIVITY, &slot->connectivity, axlf, xclbin);
+	if (size <= 0) {
+		if (size != 0) {
+			ret = size;
+			goto out0;
+		}
+	} else if (sizeof_section(slot->connectivity, m_connection) != size) {
+		ret = -EINVAL;
+		goto out0;
+	}
+
+	/* Populating MEM_TOPOLOGY sections */
+	size = zocl_read_sect(MEM_TOPOLOGY, &slot->topology, axlf, xclbin);
+	if (size <= 0) {
+		if (size != 0) {
+			ret = size;
+			goto out0;
+		}
+	} else if (sizeof_section(slot->topology, m_mem_data) != size) {
+		ret = -EINVAL;
+		goto out0;
+	}
+
+	zocl_clear_mem_slot(zdev, slot->slot_idx);
+	/* Initialize the memory for the new xclbin */
+	zocl_init_mem(zdev, slot);
+
+	/* Createing AIE Partition */
+	write_unlock(&zdev->attr_rwlock);
+	zocl_create_aie(zdev, axlf, aie_res,hw_gen);
+	write_lock(&zdev->attr_rwlock);
+
+	/*
+	 * Remember xclbin_uuid for opencontext.
+	 */
+	slot->slot_xclbin->zx_refcnt = 0;
+	if(ZOCL_PLATFORM_ARM64)
+		zocl_xclbin_set_dtbo_path(slot, axlf_obj->za_dtbo_path,
+				axlf_obj->za_dtbo_path_len);
+	zocl_xclbin_set_uuid(slot, &axlf_head.m_header.uuid);
+
+	/*
+	 * Invoking kernel thread (kthread), hence need
+	 * to call this outside of the atomic context
+	 */
+	write_unlock(&zdev->attr_rwlock);
+
+	/* Destroy the CUs specific for this slot */
+	zocl_destroy_cu_slot(zdev, slot->slot_idx);
+
+	/* Create the CUs for this slot */
+	ret = zocl_create_cu(zdev, slot);
+	if (ret) {
+		write_lock(&zdev->attr_rwlock);
+		goto out0;
+	}
+
+	ret = zocl_kds_update(zdev, slot, &axlf_obj->kds_cfg);
+	if (ret) {
+		write_lock(&zdev->attr_rwlock);
+		goto out0;
+	}
+
+	write_lock(&zdev->attr_rwlock);
+
+out0:
+	write_unlock(&zdev->attr_rwlock);
+	vfree(aie_res);
+	vfree(axlf);
+	DRM_INFO("%s %pUb ret: %d", __func__, zocl_xclbin_get_uuid(slot),
+		ret);
+	mutex_unlock(&slot->slot_xclbin_lock);
+	return ret;
+}
+
+void *
+zocl_xclbin_get_uuid(struct drm_zocl_slot *slot)
+{
+	BUG_ON(!mutex_is_locked(&slot->slot_xclbin_lock));
+	if (!slot->slot_xclbin)
+		return NULL;
+
+	return slot->slot_xclbin->zx_uuid;
+}
+
+/*
+ * Block the bitstream for this slot. This will increase reference count.
+ *
+ * @param       slot:	slot specific structure
+ * @param       id:	xclbin uuid
+ *
+ * @return      0 on success, -EBUSY if already locked, Error code on failure.
+ */
+int
+zocl_xclbin_hold(struct drm_zocl_slot *slot, const uuid_t *id)
+{
+	xuid_t *xclbin_id = (xuid_t *)zocl_xclbin_get_uuid(slot);
+
+	if (!xclbin_id) {
+		DRM_ERROR("No active xclbin. Cannot hold ");
+		return -EINVAL;
+	}
+
+	// check whether uuid is null or not
+	if (uuid_is_null(id)) {
+		DRM_WARN("NULL uuid to hold\n");
+		return -EINVAL;
+	}
+	BUG_ON(!mutex_is_locked(&slot->slot_xclbin_lock));
+
+	if (!uuid_equal(id, xclbin_id)) {
+		DRM_ERROR("lock bitstream %pUb failed, on Slot: %pUb",
+		    id, xclbin_id);
+		return -EBUSY;
+	}
+
+	slot->slot_xclbin->zx_refcnt++;
+	DRM_INFO("bitstream %pUb locked, ref=%d",
+		 id, slot->slot_xclbin->zx_refcnt);
+
+	return 0;
+}
+
+/*
+ * Lock this bitstream for this slot. This will help to protect the slot
+ * for accidental update of new xclbin.
+ *
+ * @param       slot:	slot specific structure
+ * @param       id:	xclbin uuid
+ *
+ * @return      0 on success, -EBUSY if already locked, Error code on failure.
+ */
+int zocl_lock_bitstream(struct drm_zocl_slot *slot, const uuid_t *id)
+{
+	int ret = 0;
+
+	mutex_lock(&slot->slot_xclbin_lock);
+	ret = zocl_xclbin_hold(slot, id);
+	mutex_unlock(&slot->slot_xclbin_lock);
+
+	return ret;
+}
+
+/*
+ * Release this bitstream for this slot. Also decrease the reference count
+ * for this slot.
+ *
+ * @param       slot:	slot specific structure
+ * @param       id:	xclbin uuid
+ *
+ * @return      0 on success Error code on failure.
+ */
+int
+zocl_xclbin_release(struct drm_zocl_slot *slot, const uuid_t *id)
+{
+	xuid_t *xclbin_uuid = (xuid_t *)zocl_xclbin_get_uuid(slot);
+
+	if (!xclbin_uuid) {
+		DRM_ERROR("No active xclbin. Cannot release");
+		return -EINVAL;
+	}
+
+	BUG_ON(!mutex_is_locked(&slot->slot_xclbin_lock));
+
+	if (uuid_is_null(id)) /* force unlock all */
+		slot->slot_xclbin->zx_refcnt = 0;
+	else if (uuid_equal(xclbin_uuid, id))
+		--slot->slot_xclbin->zx_refcnt;
+	else {
+		DRM_WARN("unlock bitstream %pUb failed, on device: %pUb",
+			 id, xclbin_uuid);
+		return -EINVAL;
+	}
+
+	DRM_INFO("bitstream %pUb unlocked, ref=%d",
+		 xclbin_uuid, slot->slot_xclbin->zx_refcnt);
+
+	return 0;
+}
+
+/*
+ * Unlock this bitstream for this slot. This will help to reload a new xclbin
+ * for this slot.
+ *
+ * @param       slot:	slot specific structure
+ * @param       id:	xclbin uuid
+ *
+ * @return      0 on success Error code on failure.
+ */
+int zocl_unlock_bitstream(struct drm_zocl_slot *slot, const uuid_t *id)
+{
+	int ret = 0;
+
+	mutex_lock(&slot->slot_xclbin_lock);
+	ret = zocl_xclbin_release(slot, id);
+	mutex_unlock(&slot->slot_xclbin_lock);
+
+	return ret;
+}
+
+/*
+ * Set this uuid for this slot.
+ *
+ * @param       slot:	slot specific structure
+ * @param       id:	xclbin uuid
+ *
+ * @return      0 on success Error code on failure.
+ */
+int
+zocl_xclbin_set_uuid(struct drm_zocl_slot *slot, void *uuid)
+{
+	xuid_t *zx_uuid = slot->slot_xclbin->zx_uuid;
+
+	if (zx_uuid) {
+		vfree(zx_uuid);
+		zx_uuid = NULL;
+	}
+
+	zx_uuid = vmalloc(UUID_SIZE * sizeof(u8));
+	if (!zx_uuid)
+		return -ENOMEM;
+
+	uuid_copy(zx_uuid, uuid);
+	slot->slot_xclbin->zx_uuid = zx_uuid;
+	return 0;
+}
+
+/*
+ * Initialize the xclbin for this slot. Allocate necessery memory for the
+ * same.
+ *
+ * @param       slot:	slot specific structure
+ *
+ * @return      0 on success Error code on failure.
+ */
+int
+zocl_xclbin_init(struct drm_zocl_slot *slot)
+{
+	struct zocl_xclbin *z_xclbin = NULL;
+
+	z_xclbin = vmalloc(sizeof(struct zocl_xclbin));
+	if (!z_xclbin) {
+		DRM_ERROR("Alloc slot_xclbin failed: no memory\n");
+		return -ENOMEM;
+	}
+
+	z_xclbin->zx_refcnt = 0;
+	z_xclbin->zx_dtbo_path = NULL;
+	z_xclbin->zx_uuid = NULL;
+
+	slot->slot_xclbin = z_xclbin;
+
+	return 0;
+}
+
+/*
+ * Cleanup the xclbin for this slot. Also destroy the CUs associated with this
+ * slot.
+ *
+ * @param       zdev:	zocl device structure
+ * @param       slot:	slot specific structure
+ *
+ * @return      0 on success Error code on failure.
+ */
+void
+zocl_xclbin_fini(struct drm_zocl_dev *zdev, struct drm_zocl_slot *slot)
+{
+	if (!slot->slot_xclbin)
+		return;
+
+	vfree(slot->slot_xclbin->zx_uuid);
+	slot->slot_xclbin->zx_uuid = NULL;
+	vfree(slot->slot_xclbin);
+	slot->slot_xclbin = NULL;
+
+	/* Delete CU devices if exist for this slot */
+	zocl_destroy_cu_slot(zdev, slot->slot_idx);
+}
+
+/*
+ * Set dtbo path for this slot.
+ *
+ * @param       slot:   slot specific structure
+ * @param       dtbo_path: path that stores device tree overlay
+ *
+ * @return      0 on success Error code on failure.
+ */
+int
+zocl_xclbin_set_dtbo_path(struct drm_zocl_slot *slot, char *dtbo_path,
+		uint32_t len)
+{
+        char *path = slot->slot_xclbin->zx_dtbo_path;
+
+        if (path) {
+                vfree(path);
+                path = NULL;
+        }
+
+	if(dtbo_path) {
+		path = vmalloc(len + 1);
+		if (!path)
+			return -ENOMEM;
+		copy_from_user(path, dtbo_path, len);
+		path[len] = '\0';
+	}
+
+        slot->slot_xclbin->zx_dtbo_path = path;
+        return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_xgq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_xgq.c
@@ -0,0 +1,376 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+#include <linux/completion.h>
+#include <linux/timer.h>
+#include <linux/delay.h>
+#include "zocl_drv.h"
+#include "zocl_util.h"
+#include "zocl_xgq_plat.h"
+#include "xgq_impl.h"
+#include "zocl_ert_intc.h"
+#include "zocl_xgq.h"
+
+#define ZXGQ2PDEV(zxgq)			((zxgq)->zx_pdev)
+#define ZXGQ2DEV(zxgq)			(&ZXGQ2PDEV(zxgq)->dev)
+#define zxgq_err(zxgq, fmt, args...)	zocl_err(ZXGQ2DEV(zxgq), fmt"\n", ##args)
+#define zxgq_info(zxgq, fmt, args...)	zocl_info(ZXGQ2DEV(zxgq), fmt"\n", ##args)
+#define zxgq_dbg(zxgq, fmt, args...)	zocl_dbg(ZXGQ2DEV(zxgq), fmt"\n", ##args)
+/* Timer for non-intr driven XGQs. */
+#define ZXGQ_IS_INTR_ENABLED(zxgq)	((zxgq)->zx_intc_pdev != NULL)
+#define	ZXGQ_THREAD_TIMER		(HZ / 20) /* in jiffies */
+
+#define ZXGQ_IP_SQ_PROD			0x0
+#define ZXGQ_IP_CQ_PROD			0x100
+#define ZXGQ_IP_CQ_CONF			0x10C
+#define ZXGQ_IP_RESET			(0x1 << 31)
+
+struct zocl_xgq {
+	struct platform_device	*zx_pdev;
+	struct platform_device	*zx_intc_pdev;
+	struct xgq		zx_xgq;
+
+	struct workqueue_struct	*zx_wq;
+	struct work_struct	zx_worker;
+	bool			zx_worker_stop;
+	struct completion	zx_comp;
+
+	u32			zx_irq;
+	struct timer_list	zx_timer;
+
+	size_t			zx_slot_size;
+
+	void __iomem		*zx_cq_prod_int;
+	zxgq_cmd_handler	zx_cmd_handler;
+
+	spinlock_t		zx_lock;
+
+	u64			zx_num_requests;
+	u64			zx_num_responses;
+	u64			zx_num_dropped_responses;
+
+	bool			zx_simple_cmd_hdr;
+};
+
+static inline void reg_write(void __iomem  *addr, u32 val)
+{
+	iowrite32(val, addr);
+}
+
+static inline u32 reg_read(void __iomem *addr)
+{
+	return ioread32(addr);
+}
+
+/* It's tempting to use memcpy_fromio(), but it is very slow. */
+static inline void cpy_fromio(void *tgt, u64 src, size_t cnt)
+{
+	u32 *t = tgt;
+	void __iomem *s = (void __iomem *)(uintptr_t)src;
+	size_t n_words = cnt / sizeof(*t);
+	size_t i;
+
+	for (i = 0; i < n_words; i++, s += sizeof(*t))
+		t[i] = ioread32(s);
+}
+
+/* It's tempting to use memcpy_toio(), but it is very slow. */
+static inline void cpy_toio(u64 tgt, void *src, size_t cnt)
+{
+	u32 *s = src;
+	void __iomem *t = (void __iomem *)(uintptr_t)tgt;
+	size_t n_words = cnt / sizeof(*s);
+	size_t i;
+
+	for (i = 0; i < n_words; i++, t += sizeof(*s))
+		iowrite32(s[i], t);
+}
+
+static inline void zxgq_trigger_cq_intr(struct zocl_xgq *zxgq)
+{
+	if (unlikely(!zxgq->zx_cq_prod_int))
+		return;
+	reg_write(zxgq->zx_cq_prod_int, (1U << zxgq->zx_irq));
+}
+
+static int zxgq_fetch_request(struct zocl_xgq *zxgq, struct xgq_cmd_sq_hdr **cmd)
+{
+	int rc;
+	u64 cmd_addr;
+	size_t cnt;
+	struct xgq *xgq = &zxgq->zx_xgq;
+	const size_t header_sz = sizeof(struct xgq_cmd_sq_hdr);
+	void *buf = NULL;
+
+	rc = xgq_consume(xgq, &cmd_addr);
+	if (unlikely(rc))
+		return rc;
+
+	buf = kmalloc(zxgq->zx_slot_size, GFP_KERNEL);
+	if (unlikely(!buf))
+		return -ENOMEM;
+	*cmd = (struct xgq_cmd_sq_hdr *)buf;
+
+	/* Only need first word in header for optimization. */
+	if (likely(zxgq->zx_simple_cmd_hdr))
+		cpy_fromio(buf, cmd_addr, sizeof(u32));
+	else
+		cpy_fromio(buf, cmd_addr, header_sz);
+	cnt = (*cmd)->count;
+	if (unlikely(cnt + header_sz > zxgq->zx_slot_size)) {
+		cnt = zxgq->zx_slot_size - header_sz;
+		zxgq_err(zxgq, "Payload size %dB is too big, truncated!", (*cmd)->count);
+	}
+	cpy_fromio(buf + header_sz, cmd_addr + header_sz, cnt);
+
+	xgq_notify_peer_consumed(xgq);
+
+	return 0;
+}
+
+/* Implementing echo mode for perf test. */
+static void zxgq_req_receiver_noop(struct work_struct *work)
+{
+	struct zocl_xgq *zxgq = container_of(work, struct zocl_xgq, zx_worker);
+	struct xgq *q = &zxgq->zx_xgq;
+	u64 slot_addr;
+
+	zxgq_info(zxgq, "XGQ NO-OP thread started");
+
+	while (!zxgq->zx_worker_stop) {
+		size_t cmds = 0;
+		int rc = 0;
+
+		while (rc != -ENOENT) {
+			rc = xgq_consume(q, &slot_addr);
+			if (likely(!rc))
+				cmds++;
+		}
+		if (likely(cmds)) {
+			xgq_notify_peer_consumed(q);
+			while (cmds-- > 0)
+				xgq_produce(q, &slot_addr);
+			xgq_notify_peer_produced(q);
+			zxgq_trigger_cq_intr(zxgq);
+		}
+		wait_for_completion_interruptible(&zxgq->zx_comp);
+	}
+
+	zxgq_info(zxgq, "XGQ NO-OP thread stopped");
+}
+
+static void zxgq_req_receiver(struct work_struct *work)
+{
+	int rc = 0;
+	int loop_cnt = 0;
+	struct xgq_cmd_sq_hdr *cmd = NULL;
+	struct zocl_xgq *zxgq = container_of(work, struct zocl_xgq, zx_worker);
+
+	zxgq_info(zxgq, "XGQ thread started");
+
+	while (!zxgq->zx_worker_stop) {
+		/* Avoid large number of incoming requests leads to more 120 sec blocking */
+		if (++loop_cnt == 8) {
+			loop_cnt = 0;
+			schedule();
+		}
+
+		rc = zxgq_fetch_request(zxgq, &cmd);
+		if (unlikely(rc == -ENOENT)) {
+			if (ZXGQ_IS_INTR_ENABLED(zxgq)) {
+				wait_for_completion_interruptible(&zxgq->zx_comp);
+			} else {
+				/* Timer is not reliable, add a timeout as a backup. */
+				wait_for_completion_interruptible_timeout(&zxgq->zx_comp,
+									  ZXGQ_THREAD_TIMER * 2);
+			}
+			continue;
+		}
+		if (unlikely(rc)) {
+			zxgq_err(zxgq, "XGQ access failed: %d", rc);
+			break;
+		}
+
+		zxgq->zx_num_requests++;
+		zxgq->zx_cmd_handler(zxgq->zx_pdev, cmd);
+		cmd = NULL;
+	}
+
+	zxgq_info(zxgq, "XGQ thread stopped");
+}
+
+static void zxgq_timer(struct timer_list *t)
+{
+	struct zocl_xgq *zxgq = from_timer(zxgq, t, zx_timer);
+
+	complete(&zxgq->zx_comp);
+	/* We're a periodic timer. */
+	mod_timer(&zxgq->zx_timer, jiffies + ZXGQ_THREAD_TIMER);
+}
+
+static void zxgq_start_worker(struct zocl_xgq *zxgq)
+{
+	init_completion(&zxgq->zx_comp);
+
+	/* Dedicated thread for listening to peer request. */
+	zxgq->zx_wq = create_singlethread_workqueue(dev_name(ZXGQ2DEV(zxgq)));
+	if (!zxgq->zx_wq) {
+		zxgq_err(zxgq, "failed to create xgq work queue");
+		return;
+	}
+
+	if (zxgq->zx_cmd_handler)
+		INIT_WORK(&zxgq->zx_worker, zxgq_req_receiver);
+	else
+		INIT_WORK(&zxgq->zx_worker, zxgq_req_receiver_noop);
+	queue_work(zxgq->zx_wq, &zxgq->zx_worker);
+}
+
+static void zxgq_stop_worker(struct zocl_xgq *zxgq)
+{
+	if (!zxgq->zx_wq)
+		return;
+
+	zxgq->zx_worker_stop = true;
+	complete(&zxgq->zx_comp);
+
+	cancel_work_sync(&zxgq->zx_worker);
+	destroy_workqueue(zxgq->zx_wq);
+	zxgq->zx_wq = NULL;
+}
+
+static irqreturn_t zxgq_isr(int irq, void *arg)
+{
+	struct zocl_xgq *zxgq = (struct zocl_xgq *)arg;
+
+	zxgq_dbg(zxgq, "Interrupt received on %d", irq);
+	complete(&zxgq->zx_comp);
+
+	return IRQ_HANDLED;
+}
+
+static int zxgq_post_resp(struct zocl_xgq *zxgq, struct xgq_com_queue_entry *resp)
+{
+	int ret;
+	u64 comp_addr;
+	unsigned long irqflags;
+	struct xgq *xgq = &zxgq->zx_xgq;
+
+	spin_lock_irqsave(&zxgq->zx_lock, irqflags);
+	ret = xgq_produce(xgq, &comp_addr);
+	if (likely(!ret)) {
+		if (unlikely(resp))
+			cpy_toio(comp_addr, resp, sizeof(*resp));
+		xgq_notify_peer_produced(xgq);
+		zxgq_trigger_cq_intr(zxgq);
+		zxgq->zx_num_responses++;
+	}
+	spin_unlock_irqrestore(&zxgq->zx_lock, irqflags);
+
+	return ret;
+}
+
+void zxgq_send_response(void *zxgq_hdl, struct xgq_com_queue_entry *resp)
+{
+	int ret;
+	unsigned long irqflags;
+	const unsigned int sleep = 50; /* in ms */
+	const unsigned int max_sleep = sleep * 100; /* in ms */
+	u64 total_slept = 0;
+	struct zocl_xgq *zxgq = (struct zocl_xgq *)zxgq_hdl;
+
+	while ((ret = zxgq_post_resp(zxgq, resp)) == -ENOSPC) {
+		msleep(sleep);
+		total_slept += sleep;
+		if (total_slept >= max_sleep)
+			break;
+	}
+	if (unlikely(ret)) {
+		spin_lock_irqsave(&zxgq->zx_lock, irqflags);
+		zxgq->zx_num_dropped_responses++;
+		spin_unlock_irqrestore(&zxgq->zx_lock, irqflags);
+		zxgq_err(zxgq, "Failed to send response, dropped: %d", ret);
+	}
+}
+
+void *zxgq_init(struct zocl_xgq_init_args *arg)
+{
+	int rc;
+	u64 flags = 0;
+	size_t ringsz = arg->zxia_ring_size;
+	struct zocl_xgq *zxgq = devm_kzalloc(&arg->zxia_pdev->dev, sizeof(*zxgq), GFP_KERNEL);
+	u64 sqprod = 0, cqprod = 0;
+
+	if (!zxgq)
+		return NULL;
+	zxgq->zx_pdev = arg->zxia_pdev;
+	zxgq->zx_irq = arg->zxia_irq;
+	zxgq->zx_slot_size = arg->zxia_ring_slot_size;
+	zxgq->zx_cq_prod_int = arg->zxia_cq_prod_int;
+	zxgq->zx_cmd_handler = arg->zxia_cmd_handler;
+	zxgq->zx_simple_cmd_hdr = arg->zxia_simple_cmd_hdr;
+	zxgq->zx_intc_pdev = arg->zxia_intc_pdev;
+
+	if (!arg->zxia_xgq_ip) {
+		flags |= XGQ_IN_MEM_PROD;
+	} else {
+		sqprod = (u64)(uintptr_t)(arg->zxia_xgq_ip + ZXGQ_IP_SQ_PROD);
+		cqprod = (u64)(uintptr_t)(arg->zxia_xgq_ip + ZXGQ_IP_CQ_PROD);
+	}
+	/* Reset ring buffer. */
+	memset_io(arg->zxia_ring, 0, ringsz);
+
+	rc = xgq_alloc(&zxgq->zx_xgq, flags, 0, (u64)(uintptr_t)arg->zxia_ring, &ringsz,
+		       zxgq->zx_slot_size, sqprod, cqprod);
+	if (rc) {
+		zxgq_err(zxgq, "failed to alloc XGQ: %d", rc);
+		return NULL;
+	}
+
+	spin_lock_init(&zxgq->zx_lock);
+
+	zxgq_start_worker(zxgq);
+
+	if (ZXGQ_IS_INTR_ENABLED(zxgq)) {
+		zocl_ert_intc_add(zxgq->zx_intc_pdev, zxgq->zx_irq, zxgq_isr, zxgq);
+	} else {
+		timer_setup(&zxgq->zx_timer, zxgq_timer, 0);
+		mod_timer(&zxgq->zx_timer, jiffies + ZXGQ_THREAD_TIMER);
+	}
+
+	zxgq_info(zxgq, "Initialized XGQ with irq=%d, ring size=%ld, slot size=%ld",
+		  ZXGQ_IS_INTR_ENABLED(zxgq) ? zxgq->zx_irq : -1, ringsz, zxgq->zx_slot_size);
+	return zxgq;
+}
+
+void zxgq_fini(void *zxgq_hdl)
+{
+	struct zocl_xgq *zxgq = (struct zocl_xgq *)zxgq_hdl;
+	struct platform_device *intc = zxgq->zx_intc_pdev;
+
+	if (intc)
+		zocl_ert_intc_remove(intc, zxgq->zx_irq);
+	else
+		del_timer_sync(&zxgq->zx_timer);
+
+	zxgq_stop_worker(zxgq);
+
+	/* Don't leave until we have seen responses for all requests we have sent out. */
+	while (zxgq->zx_num_requests != zxgq->zx_num_responses + zxgq->zx_num_dropped_responses) {
+		zxgq_err(zxgq, "Outstanding requests detected: reqs=%lld, resp=%lld, dropped=%lld",
+			 zxgq->zx_num_requests, zxgq->zx_num_responses,
+			 zxgq->zx_num_dropped_responses);
+		ssleep(3);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/drm/zocl/zocl_xgq_intc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/drm/zocl/zocl_xgq_intc.c
@@ -0,0 +1,167 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Apache-2.0 */
+/*
+ * Copyright (C) 2021 Xilinx, Inc. All rights reserved.
+ *
+ * Author(s):
+ *        Max Zhen <maxz@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include "zocl_lib.h"
+#include "zocl_ert_intc.h"
+
+/* ERT INTC driver name. */
+#define ZINTC_NAME			"zocl_xgq_intc"
+
+#define ZINTC2PDEV(zintc)		((zintc)->zei_pdev)
+#define ZINTC2DEV(zintc)		(&ZINTC2PDEV(zintc)->dev)
+#define zintc_err(zintc, fmt, args...)	zocl_err(ZINTC2DEV(zintc), fmt"\n", ##args)
+#define zintc_info(zintc, fmt, args...)	zocl_info(ZINTC2DEV(zintc), fmt"\n", ##args)
+#define zintc_dbg(zintc, fmt, args...)	zocl_dbg(ZINTC2DEV(zintc), fmt"\n", ##args)
+
+struct zocl_xgq_intc {
+	struct platform_device		*zei_pdev;
+
+	spinlock_t			zei_lock;
+
+	int				zei_num_irqs;
+	/* variable length based on num of irqs, always the last member */
+	struct zocl_ert_intc_handler	zei_handler[0];
+};
+
+static irqreturn_t zintc_isr(int irq, void *arg)
+{
+	unsigned long irqflags;
+	struct zocl_ert_intc_handler *h = (struct zocl_ert_intc_handler *)arg;
+	struct zocl_xgq_intc *zintc = platform_get_drvdata(h->zeih_pdev);
+
+	spin_lock_irqsave(&zintc->zei_lock, irqflags);
+	if (h->zeih_cb && h->zeih_enabled)
+		h->zeih_cb(irq, h->zeih_arg);
+	else
+		zintc_err(zintc, "Spurious interrupt received on %d", irq); 
+	spin_unlock_irqrestore(&zintc->zei_lock, irqflags);
+	return IRQ_HANDLED;
+}
+
+static int zintc_probe(struct platform_device *pdev)
+{
+	int ret;
+	int i;
+	struct zocl_xgq_intc *zintc;
+	int num_irqs = platform_irq_count(pdev);
+
+	if (num_irqs <= 0) {
+		zocl_err(&pdev->dev, "failed to find IRQs, num of IRQ: %d\n", num_irqs); 
+		return -EINVAL;
+	}
+
+	zintc = devm_kzalloc(&pdev->dev,
+			     sizeof(*zintc) + sizeof(struct zocl_ert_intc_handler) * num_irqs,
+			     GFP_KERNEL);
+	if (!zintc)
+		return -ENOMEM;
+	zintc->zei_pdev = pdev;
+	zintc->zei_num_irqs = num_irqs;
+	spin_lock_init(&zintc->zei_lock);
+	platform_set_drvdata(pdev, zintc);
+
+	/* Ready to turn on interrupts! */
+	for (i = 0; i < num_irqs; i++) {
+		struct zocl_ert_intc_handler *h = &zintc->zei_handler[i];
+		struct resource *res = platform_get_resource(ZINTC2PDEV(zintc), IORESOURCE_IRQ, i);
+		u32 irq = res->start;
+
+		h->zeih_pdev = pdev;
+		h->zeih_irq = irq;
+		BUG_ON(irq < 0);
+		ret = devm_request_irq(ZINTC2DEV(zintc), irq, zintc_isr, 0, ZINTC_NAME, h);
+		if (ret)
+			zintc_err(zintc, "failed to add isr for IRQ: %d: %d", irq, ret); 
+		else
+			zintc_info(zintc, "managing IRQ %d", irq); 
+	}
+
+	return 0;
+}
+
+static int zintc_remove(struct platform_device *pdev)
+{
+	struct zocl_xgq_intc *zintc = platform_get_drvdata(pdev);
+
+	zintc_info(zintc, "Removing %s", ZINTC_NAME);
+	return 0;
+}
+
+/*
+ * Interfaces exposed to other subdev drivers.
+ */
+
+static struct zocl_ert_intc_handler *find_handler(struct zocl_xgq_intc *zintc, u32 irq)
+{
+	int i;
+	struct zocl_ert_intc_handler *h;
+
+	for (i = 0; i < zintc->zei_num_irqs; i++) {
+		h = &zintc->zei_handler[i];
+		if (h->zeih_irq == irq)
+			return h;
+	}
+	return NULL;
+}
+
+static void zocl_xgq_intc_add(struct platform_device *pdev, u32 irq, irq_handler_t cb, void *arg)
+{
+	unsigned long irqflags;
+	struct zocl_xgq_intc *zintc = platform_get_drvdata(pdev);
+	struct zocl_ert_intc_handler *h = find_handler(zintc, irq);
+
+	BUG_ON(!h);
+	spin_lock_irqsave(&zintc->zei_lock, irqflags);
+
+	BUG_ON(h->zeih_cb);
+	h->zeih_cb = cb;
+	h->zeih_arg = arg;
+	h->zeih_enabled = true;
+
+	spin_unlock_irqrestore(&zintc->zei_lock, irqflags);
+}
+
+static void zocl_xgq_intc_remove(struct platform_device *pdev, u32 irq)
+{
+	unsigned long irqflags;
+	struct zocl_xgq_intc *zintc = platform_get_drvdata(pdev);
+	struct zocl_ert_intc_handler *h = find_handler(zintc, irq);
+
+	BUG_ON(!h);
+	spin_lock_irqsave(&zintc->zei_lock, irqflags);
+
+	h->zeih_cb = NULL;
+	h->zeih_arg = NULL;
+	h->zeih_enabled = false;
+
+	spin_unlock_irqrestore(&zintc->zei_lock, irqflags);
+}
+
+static struct zocl_ert_intc_drv_data zocl_xgq_intc_drvdata = {
+	.add = zocl_xgq_intc_add,
+	.remove = zocl_xgq_intc_remove,
+};
+
+static const struct platform_device_id zocl_xgq_intc_id_match[] = {
+	{ ERT_XGQ_INTC_DEV_NAME, (kernel_ulong_t)&zocl_xgq_intc_drvdata },
+	{ /* end of table */ },
+};
+
+struct platform_driver zocl_xgq_intc_driver = {
+	.driver = {
+		.name = ZINTC_NAME,
+	},
+	.probe  = zintc_probe,
+	.remove = zintc_remove,
+	.id_table = zocl_xgq_intc_id_match,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/host1x/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/host1x/Kconfig
@@ -2,6 +2,7 @@
 config TEGRA_HOST1X
 	tristate "NVIDIA Tegra host1x driver"
 	depends on ARCH_TEGRA || (ARM && COMPILE_TEST)
+	select DMA_SHARED_BUFFER
 	select IOMMU_IOVA
 	help
 	  Driver for the NVIDIA Tegra host1x hardware.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/host1x/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/host1x/bus.c
@@ -367,11 +367,6 @@
 	return 0;
 }
 
-static int host1x_dma_configure(struct device *dev)
-{
-	return of_dma_configure(dev, dev->of_node, true);
-}
-
 static const struct dev_pm_ops host1x_device_pm_ops = {
 	.suspend = pm_generic_suspend,
 	.resume = pm_generic_resume,
@@ -385,7 +380,6 @@
 	.name = "host1x",
 	.match = host1x_device_match,
 	.uevent = host1x_device_uevent,
-	.dma_configure = host1x_dma_configure,
 	.pm = &host1x_device_pm_ops,
 };
 
@@ -474,8 +468,6 @@
 	device->dev.bus = &host1x_bus_type;
 	device->dev.parent = host1x->dev;
 
-	of_dma_configure(&device->dev, host1x->dev->of_node, true);
-
 	device->dev.dma_parms = &device->dma_parms;
 	dma_set_max_seg_size(&device->dev, UINT_MAX);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/host1x/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/host1x/dev.c
@@ -18,6 +18,10 @@
 #include <trace/events/host1x.h>
 #undef CREATE_TRACE_POINTS
 
+#if IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU)
+#include <asm/dma-iommu.h>
+#endif
+
 #include "bus.h"
 #include "channel.h"
 #include "debug.h"
@@ -200,6 +204,10 @@
 
 static bool host1x_wants_iommu(struct host1x *host1x)
 {
+	/* Our IOMMU usage policy doesn't currently play well with GART */
+	if (of_machine_is_compatible("nvidia,tegra20"))
+		return false;
+
 	/*
 	 * If we support addressing a maximum of 32 bits of physical memory
 	 * and if the host1x firewall is enabled, there's no need to enable
@@ -238,6 +246,17 @@
 	struct iommu_domain *domain = iommu_get_domain_for_dev(host->dev);
 	int err;
 
+#if IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU)
+	if (host->dev->archdata.mapping) {
+		struct dma_iommu_mapping *mapping =
+				to_dma_iommu_mapping(host->dev);
+		arm_iommu_detach_device(host->dev);
+		arm_iommu_release_mapping(mapping);
+
+		domain = iommu_get_domain_for_dev(host->dev);
+	}
+#endif
+
 	/*
 	 * We may not always want to enable IOMMU support (for example if the
 	 * host1x firewall is already enabled and we don't support addressing
@@ -511,6 +530,7 @@
 	host1x_syncpt_deinit(host);
 	reset_control_assert(host->rst);
 	clk_disable_unprepare(host->clk);
+	host1x_channel_list_free(&host->channel_list);
 	host1x_iommu_exit(host);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/host1x/hw/syncpt_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/host1x/hw/syncpt_hw.c
@@ -106,9 +106,6 @@
 #if HOST1X_HW >= 6
 	struct host1x *host = sp->host;
 
-	if (!host->hv_regs)
-		return;
-
 	host1x_sync_writel(host,
 			   HOST1X_SYNC_SYNCPT_CH_APP_CH(ch ? ch->id : 0xff),
 			   HOST1X_SYNC_SYNCPT_CH_APP(sp->id));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/host1x/syncpt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/host1x/syncpt.c
@@ -225,27 +225,12 @@
 	void *ref;
 	struct host1x_waitlist *waiter;
 	int err = 0, check_count = 0;
-	u32 val;
 
 	if (value)
-		*value = 0;
-
-	/* first check cache */
-	if (host1x_syncpt_is_expired(sp, thresh)) {
-		if (value)
-			*value = host1x_syncpt_load(sp);
+		*value = host1x_syncpt_load(sp);
 
+	if (host1x_syncpt_is_expired(sp, thresh))
 		return 0;
-	}
-
-	/* try to read from register */
-	val = host1x_hw_syncpt_load(sp->host, sp);
-	if (host1x_syncpt_is_expired(sp, thresh)) {
-		if (value)
-			*value = val;
-
-		goto done;
-	}
 
 	if (!timeout) {
 		err = -EAGAIN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/ipu-v3/ipu-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/ipu-v3/ipu-common.c
@@ -1165,6 +1165,7 @@
 		pdev = platform_device_alloc(reg->name, id++);
 		if (!pdev) {
 			ret = -ENOMEM;
+			of_node_put(of_node);
 			goto err_register;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/gpu/ipu-v3/ipu-di.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/gpu/ipu-v3/ipu-di.c
@@ -447,8 +447,9 @@
 
 		error = rate / (sig->mode.pixelclock / 1000);
 
-		dev_dbg(di->ipu->dev, "  IPU clock can give %lu with divider %u, error %d.%u%%\n",
-			rate, div, (signed)(error - 1000) / 10, error % 10);
+		dev_dbg(di->ipu->dev, "  IPU clock can give %lu with divider %u, error %c%d.%d%%\n",
+			rate, div, error < 1000 ? '-' : '+',
+			abs(error - 1000) / 10, abs(error - 1000) % 10);
 
 		/* Allow a 1% error */
 		if (error < 1010 && error >= 990) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/greybus/interface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/greybus/interface.c
@@ -694,6 +694,7 @@
 
 	trace_gb_interface_release(intf);
 
+	cancel_work_sync(&intf->mode_switch_work);
 	kfree(intf);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/greybus/svc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/greybus/svc.c
@@ -866,8 +866,14 @@
 
 	gb_svc_debugfs_init(svc);
 
-	return gb_svc_queue_deferred_request(op);
+	ret = gb_svc_queue_deferred_request(op);
+	if (ret)
+		goto err_remove_debugfs;
 
+	return 0;
+
+err_remove_debugfs:
+	gb_svc_debugfs_exit(svc);
 err_unregister_device:
 	gb_svc_watchdog_destroy(svc);
 	device_del(&svc->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/Kconfig
@@ -207,14 +207,14 @@
 
 config HID_CHICONY
 	tristate "Chicony devices"
-	depends on HID
+	depends on USB_HID
 	default !EXPERT
 	help
 	Support for Chicony Tactical pad and special keys on Chicony keyboards.
 
 config HID_CORSAIR
 	tristate "Corsair devices"
-	depends on HID && USB && LEDS_CLASS
+	depends on USB_HID && LEDS_CLASS
 	help
 	Support for Corsair devices that are not fully compliant with the
 	HID standard.
@@ -245,7 +245,7 @@
 
 config HID_PRODIKEYS
 	tristate "Prodikeys PC-MIDI Keyboard support"
-	depends on HID && SND
+	depends on USB_HID && SND
 	select SND_RAWMIDI
 	help
 	Support for Prodikeys PC-MIDI Keyboard device support.
@@ -553,7 +553,7 @@
 
 config HID_LOGITECH
 	tristate "Logitech devices"
-	depends on HID
+	depends on USB_HID
 	depends on LEDS_CLASS
 	default !EXPERT
 	help
@@ -919,7 +919,7 @@
 
 config HID_SAMSUNG
 	tristate "Samsung InfraRed remote control or keyboards"
-	depends on HID
+	depends on USB_HID
 	help
 	Support for Samsung InfraRed remote control or keyboards.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/Makefile
@@ -144,7 +144,6 @@
 obj-$(CONFIG_I2C_HID_CORE)	+= i2c-hid/
 
 obj-$(CONFIG_INTEL_ISH_HID)	+= intel-ish-hid/
-obj-$(INTEL_ISH_FIRMWARE_DOWNLOADER)	+= intel-ish-hid/
 
 obj-$(CONFIG_AMD_SFH_HID)       += amd-sfh-hid/
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/amd-sfh-hid/amd_sfh_client.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/amd-sfh-hid/amd_sfh_client.c
@@ -154,6 +154,8 @@
 	dev = &privdata->pdev->dev;
 
 	cl_data->num_hid_devices = amd_mp2_get_sensor_num(privdata, &cl_data->sensor_idx[0]);
+	if (cl_data->num_hid_devices == 0)
+		return -ENODEV;
 
 	INIT_DELAYED_WORK(&cl_data->work, amd_sfh_work);
 	INIT_DELAYED_WORK(&cl_data->work_buffer, amd_sfh_work_buffer);
@@ -161,9 +163,13 @@
 	cl_data->in_data = in_data;
 
 	for (i = 0; i < cl_data->num_hid_devices; i++) {
-		in_data->sensor_virt_addr[i] = dma_alloc_coherent(dev, sizeof(int) * 8,
-								  &cl_data->sensor_dma_addr[i],
-								  GFP_KERNEL);
+		in_data->sensor_virt_addr[i] = dmam_alloc_coherent(dev, sizeof(int) * 8,
+								   &cl_data->sensor_dma_addr[i],
+								   GFP_KERNEL);
+		if (!in_data->sensor_virt_addr[i]) {
+			rc = -ENOMEM;
+			goto cleanup;
+		}
 		cl_data->sensor_sts[i] = SENSOR_DISABLED;
 		cl_data->sensor_requested_cnt[i] = 0;
 		cl_data->cur_hid_dev = i;
@@ -226,6 +232,17 @@
 		dev_dbg(dev, "sid 0x%x status 0x%x\n",
 			cl_data->sensor_idx[i], cl_data->sensor_sts[i]);
 	}
+	if (privdata->mp2_ops->discovery_status &&
+	    privdata->mp2_ops->discovery_status(privdata) == 0) {
+		amd_sfh_hid_client_deinit(privdata);
+		for (i = 0; i < cl_data->num_hid_devices; i++) {
+			devm_kfree(dev, cl_data->feature_report[i]);
+			devm_kfree(dev, in_data->input_report[i]);
+			devm_kfree(dev, cl_data->report_descr[i]);
+		}
+		dev_warn(dev, "Failed to discover, sensors not enabled\n");
+		return -EOPNOTSUPP;
+	}
 	schedule_delayed_work(&cl_data->work_buffer, msecs_to_jiffies(AMD_SFH_IDLE_LOOP));
 	return 0;
 
@@ -246,7 +263,6 @@
 int amd_sfh_hid_client_deinit(struct amd_mp2_dev *privdata)
 {
 	struct amdtp_cl_data *cl_data = privdata->cl_data;
-	struct amd_input_data *in_data = cl_data->in_data;
 	int i, status;
 
 	for (i = 0; i < cl_data->num_hid_devices; i++) {
@@ -265,12 +281,5 @@
 	cancel_delayed_work_sync(&cl_data->work_buffer);
 	amdtp_hid_remove(cl_data);
 
-	for (i = 0; i < cl_data->num_hid_devices; i++) {
-		if (in_data->sensor_virt_addr[i]) {
-			dma_free_coherent(&privdata->pdev->dev, 8 * sizeof(int),
-					  in_data->sensor_virt_addr[i],
-					  cl_data->sensor_dma_addr[i]);
-		}
-	}
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/amd-sfh-hid/amd_sfh_hid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/amd-sfh-hid/amd_sfh_hid.c
@@ -98,11 +98,15 @@
 
 void amdtp_hid_wakeup(struct hid_device *hid)
 {
-	struct amdtp_hid_data *hid_data = hid->driver_data;
-	struct amdtp_cl_data *cli_data = hid_data->cli_data;
+	struct amdtp_hid_data *hid_data;
+	struct amdtp_cl_data *cli_data;
 
-	cli_data->request_done[cli_data->cur_hid_dev] = true;
-	wake_up_interruptible(&hid_data->hid_wait);
+	if (hid) {
+		hid_data = hid->driver_data;
+		cli_data = hid_data->cli_data;
+		cli_data->request_done[cli_data->cur_hid_dev] = true;
+		wake_up_interruptible(&hid_data->hid_wait);
+	}
 }
 
 static struct hid_ll_driver amdtp_hid_ll_driver = {
@@ -139,10 +143,10 @@
 
 	hid->driver_data = hid_data;
 	cli_data->hid_sensor_hubs[cur_hid_dev] = hid;
-	hid->bus = BUS_AMD_AMDTP;
+	hid->bus = BUS_AMD_SFH;
 	hid->vendor = AMD_SFH_HID_VENDOR;
 	hid->product = AMD_SFH_HID_PRODUCT;
-	snprintf(hid->name, sizeof(hid->name), "%s %04X:%04X", "hid-amdtp",
+	snprintf(hid->name, sizeof(hid->name), "%s %04X:%04X", "hid-amdsfh",
 		 hid->vendor, hid->product);
 
 	rc = hid_add_device(hid);
@@ -160,11 +164,13 @@
 void amdtp_hid_remove(struct amdtp_cl_data *cli_data)
 {
 	int i;
+	struct amdtp_hid_data *hid_data;
 
 	for (i = 0; i < cli_data->num_hid_devices; ++i) {
 		if (cli_data->hid_sensor_hubs[i]) {
-			kfree(cli_data->hid_sensor_hubs[i]->driver_data);
+			hid_data = cli_data->hid_sensor_hubs[i]->driver_data;
 			hid_destroy_device(cli_data->hid_sensor_hubs[i]);
+			kfree(hid_data);
 			cli_data->hid_sensor_hubs[i] = NULL;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/amd-sfh-hid/amd_sfh_hid.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/amd-sfh-hid/amd_sfh_hid.h
@@ -10,7 +10,7 @@
 #define AMDSFH_HID_H
 
 #define MAX_HID_DEVICES		5
-#define BUS_AMD_AMDTP		0x20
+#define BUS_AMD_SFH		0x20
 #define AMD_SFH_HID_VENDOR	0x1022
 #define AMD_SFH_HID_PRODUCT	0x0001
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/amd-sfh-hid/amd_sfh_pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/amd-sfh-hid/amd_sfh_pcie.c
@@ -36,11 +36,11 @@
 {
 	union cmd_response cmd_resp;
 
-	/* Get response with status within a max of 800 ms timeout */
+	/* Get response with status within a max of 1600 ms timeout */
 	if (!readl_poll_timeout(mp2->mmio + AMD_P2C_MSG(0), cmd_resp.resp,
 				(cmd_resp.response_v2.response == sensor_sts &&
 				cmd_resp.response_v2.status == 0 && (sid == 0xff ||
-				cmd_resp.response_v2.sensor_id == sid)), 500, 800000))
+				cmd_resp.response_v2.sensor_id == sid)), 500, 1600000))
 		return cmd_resp.response_v2.response;
 
 	return SENSOR_DISABLED;
@@ -52,6 +52,7 @@
 
 	cmd_base.ul = 0;
 	cmd_base.cmd_v2.cmd_id = ENABLE_SENSOR;
+	cmd_base.cmd_v2.intr_disable = 1;
 	cmd_base.cmd_v2.period = info.period;
 	cmd_base.cmd_v2.sensor_id = info.sensor_idx;
 	cmd_base.cmd_v2.length = 16;
@@ -69,6 +70,7 @@
 
 	cmd_base.ul = 0;
 	cmd_base.cmd_v2.cmd_id = DISABLE_SENSOR;
+	cmd_base.cmd_v2.intr_disable = 1;
 	cmd_base.cmd_v2.period = 0;
 	cmd_base.cmd_v2.sensor_id = sensor_idx;
 	cmd_base.cmd_v2.length  = 16;
@@ -82,12 +84,57 @@
 	union sfh_cmd_base cmd_base;
 
 	cmd_base.cmd_v2.cmd_id = STOP_ALL_SENSORS;
+	cmd_base.cmd_v2.intr_disable = 1;
 	cmd_base.cmd_v2.period = 0;
 	cmd_base.cmd_v2.sensor_id = 0;
 
 	writel(cmd_base.ul, privdata->mmio + AMD_C2P_MSG0);
 }
 
+static void amd_sfh_clear_intr_v2(struct amd_mp2_dev *privdata)
+{
+	if (readl(privdata->mmio + AMD_P2C_MSG(4))) {
+		writel(0, privdata->mmio + AMD_P2C_MSG(4));
+		writel(0xf, privdata->mmio + AMD_P2C_MSG(5));
+	}
+}
+
+static void amd_sfh_clear_intr(struct amd_mp2_dev *privdata)
+{
+	if (privdata->mp2_ops->clear_intr)
+		privdata->mp2_ops->clear_intr(privdata);
+}
+
+static irqreturn_t amd_sfh_irq_handler(int irq, void *data)
+{
+	amd_sfh_clear_intr(data);
+
+	return IRQ_HANDLED;
+}
+
+static int amd_sfh_irq_init_v2(struct amd_mp2_dev *privdata)
+{
+	int rc;
+
+	pci_intx(privdata->pdev, true);
+
+	rc = devm_request_irq(&privdata->pdev->dev, privdata->pdev->irq,
+			      amd_sfh_irq_handler, 0, DRIVER_NAME, privdata);
+	if (rc) {
+		dev_err(&privdata->pdev->dev, "failed to request irq %d err=%d\n",
+			privdata->pdev->irq, rc);
+		return rc;
+	}
+
+	return 0;
+}
+
+static int amd_sfh_dis_sts_v2(struct amd_mp2_dev *privdata)
+{
+	return (readl(privdata->mmio + AMD_P2C_MSG(1)) &
+		      SENSOR_DISCOVERY_STATUS_MASK) >> SENSOR_DISCOVERY_STATUS_SHIFT;
+}
+
 void amd_start_sensor(struct amd_mp2_dev *privdata, struct amd_mp2_sensor_info info)
 {
 	union sfh_cmd_param cmd_param;
@@ -192,6 +239,8 @@
 	struct amd_mp2_dev *mp2 = privdata;
 	amd_sfh_hid_client_deinit(privdata);
 	mp2->mp2_ops->stop_all(mp2);
+	pci_intx(mp2->pdev, false);
+	amd_sfh_clear_intr(mp2);
 }
 
 static const struct amd_mp2_ops amd_sfh_ops_v2 = {
@@ -199,6 +248,9 @@
 	.stop = amd_stop_sensor_v2,
 	.stop_all = amd_stop_all_sensor_v2,
 	.response = amd_sfh_wait_response_v2,
+	.clear_intr = amd_sfh_clear_intr_v2,
+	.init_intr = amd_sfh_irq_init_v2,
+	.discovery_status = amd_sfh_dis_sts_v2,
 };
 
 static const struct amd_mp2_ops amd_sfh_ops = {
@@ -224,11 +276,37 @@
 	}
 }
 
+static int amd_sfh_irq_init(struct amd_mp2_dev *privdata)
+{
+	if (privdata->mp2_ops->init_intr)
+		return privdata->mp2_ops->init_intr(privdata);
+
+	return 0;
+}
+
+static const struct dmi_system_id dmi_nodevs[] = {
+	{
+		/*
+		 * Google Chromebooks use Chrome OS Embedded Controller Sensor
+		 * Hub instead of Sensor Hub Fusion and leaves MP2
+		 * uninitialized, which disables all functionalities, even
+		 * including the registers necessary for feature detections.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Google"),
+		},
+	},
+	{ }
+};
+
 static int amd_mp2_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	struct amd_mp2_dev *privdata;
 	int rc;
 
+	if (dmi_first_match(dmi_nodevs))
+		return -ENODEV;
+
 	privdata = devm_kzalloc(&pdev->dev, sizeof(*privdata), GFP_KERNEL);
 	if (!privdata)
 		return -ENOMEM;
@@ -257,13 +335,33 @@
 
 	mp2_select_ops(privdata);
 
+	rc = amd_sfh_irq_init(privdata);
+	if (rc) {
+		dev_err(&pdev->dev, "amd_sfh_irq_init failed\n");
+		return rc;
+	}
+
 	rc = amd_sfh_hid_client_init(privdata);
-	if (rc)
+	if (rc) {
+		amd_sfh_clear_intr(privdata);
+		if (rc != -EOPNOTSUPP)
+			dev_err(&pdev->dev, "amd_sfh_hid_client_init failed\n");
 		return rc;
+	}
+
+	amd_sfh_clear_intr(privdata);
 
 	return devm_add_action_or_reset(&pdev->dev, amd_mp2_pci_remove, privdata);
 }
 
+static void amd_sfh_shutdown(struct pci_dev *pdev)
+{
+	struct amd_mp2_dev *mp2 = pci_get_drvdata(pdev);
+
+	if (mp2 && mp2->mp2_ops)
+		mp2->mp2_ops->stop_all(mp2);
+}
+
 static int __maybe_unused amd_mp2_pci_resume(struct device *dev)
 {
 	struct pci_dev *pdev = to_pci_dev(dev);
@@ -287,6 +385,9 @@
 		}
 	}
 
+	schedule_delayed_work(&cl_data->work_buffer, msecs_to_jiffies(AMD_SFH_IDLE_LOOP));
+	amd_sfh_clear_intr(mp2);
+
 	return 0;
 }
 
@@ -310,6 +411,9 @@
 		}
 	}
 
+	cancel_delayed_work_sync(&cl_data->work_buffer);
+	amd_sfh_clear_intr(mp2);
+
 	return 0;
 }
 
@@ -327,6 +431,7 @@
 	.id_table	= amd_mp2_pci_tbl,
 	.probe		= amd_mp2_pci_probe,
 	.driver.pm	= &amd_mp2_pm_ops,
+	.shutdown	= amd_sfh_shutdown,
 };
 module_pci_driver(amd_mp2_pci_driver);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/amd-sfh-hid/amd_sfh_pcie.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/amd-sfh-hid/amd_sfh_pcie.h
@@ -38,6 +38,9 @@
 
 #define AMD_SFH_IDLE_LOOP	200
 
+#define SENSOR_DISCOVERY_STATUS_MASK		GENMASK(5, 3)
+#define SENSOR_DISCOVERY_STATUS_SHIFT		3
+
 /* SFH Command register */
 union sfh_cmd_base {
 	u32 ul;
@@ -48,7 +51,7 @@
 	} s;
 	struct {
 		u32 cmd_id : 4;
-		u32 intr_enable : 1;
+		u32 intr_disable : 1;
 		u32 rsvd1 : 3;
 		u32 length : 7;
 		u32 mem_type : 1;
@@ -116,10 +119,10 @@
 struct hpd_status {
 	union {
 		struct {
-			u32 human_presence_report : 4;
-			u32 human_presence_actual : 4;
-			u32 probablity		  : 8;
 			u32 object_distance       : 16;
+			u32 probablity		  : 8;
+			u32 human_presence_actual : 4;
+			u32 human_presence_report : 4;
 		} shpd;
 		u32 val;
 	};
@@ -140,5 +143,8 @@
 	 void (*stop)(struct amd_mp2_dev *privdata, u16 sensor_idx);
 	 void (*stop_all)(struct amd_mp2_dev *privdata);
 	 int (*response)(struct amd_mp2_dev *mp2, u8 sid, u32 sensor_sts);
+	 void (*clear_intr)(struct amd_mp2_dev *privdata);
+	 int (*init_intr)(struct amd_mp2_dev *privdata);
+	 int (*discovery_status)(struct amd_mp2_dev *privdata);
 };
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/amd-sfh-hid/hid_descriptor/amd_sfh_hid_desc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/amd-sfh-hid/hid_descriptor/amd_sfh_hid_desc.c
@@ -26,6 +26,7 @@
 #define HID_USAGE_SENSOR_STATE_READY_ENUM                             0x02
 #define HID_USAGE_SENSOR_STATE_INITIALIZING_ENUM                      0x05
 #define HID_USAGE_SENSOR_EVENT_DATA_UPDATED_ENUM                      0x04
+#define ILLUMINANCE_MASK					GENMASK(14, 0)
 
 int get_report_descriptor(int sensor_idx, u8 *rep_desc)
 {
@@ -245,7 +246,8 @@
 		get_common_inputs(&als_input.common_property, report_id);
 		/* For ALS ,V2 Platforms uses C2P_MSG5 register instead of DRAM access method */
 		if (supported_input == V2_STATUS)
-			als_input.illuminance_value = (int)readl(privdata->mmio + AMD_C2P_MSG(5));
+			als_input.illuminance_value =
+				readl(privdata->mmio + AMD_C2P_MSG(5)) & ILLUMINANCE_MASK;
 		else
 			als_input.illuminance_value =
 				(int)sensor_virt_addr[0] / AMD_SFH_FW_MULTIPLIER;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-alps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-alps.c
@@ -831,6 +831,8 @@
 	{ HID_DEVICE(HID_BUS_ANY, HID_GROUP_ANY,
 		USB_VENDOR_ID_ALPS_JP, HID_DEVICE_ID_ALPS_U1) },
 	{ HID_DEVICE(HID_BUS_ANY, HID_GROUP_ANY,
+		USB_VENDOR_ID_ALPS_JP, HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY) },
+	{ HID_DEVICE(HID_BUS_ANY, HID_GROUP_ANY,
 		USB_VENDOR_ID_ALPS_JP, HID_DEVICE_ID_ALPS_T4_BTNLESS) },
 	{ }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-apple.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-apple.c
@@ -70,6 +70,28 @@
 	u8 flags;
 };
 
+static const struct apple_key_translation apple2021_fn_keys[] = {
+	{ KEY_BACKSPACE, KEY_DELETE },
+	{ KEY_ENTER,	KEY_INSERT },
+	{ KEY_F1,	KEY_BRIGHTNESSDOWN, APPLE_FLAG_FKEY },
+	{ KEY_F2,	KEY_BRIGHTNESSUP,   APPLE_FLAG_FKEY },
+	{ KEY_F3,	KEY_SCALE,          APPLE_FLAG_FKEY },
+	{ KEY_F4,	KEY_SEARCH,         APPLE_FLAG_FKEY },
+	{ KEY_F5,	KEY_MICMUTE,        APPLE_FLAG_FKEY },
+	{ KEY_F6,	KEY_SLEEP,          APPLE_FLAG_FKEY },
+	{ KEY_F7,	KEY_PREVIOUSSONG,   APPLE_FLAG_FKEY },
+	{ KEY_F8,	KEY_PLAYPAUSE,      APPLE_FLAG_FKEY },
+	{ KEY_F9,	KEY_NEXTSONG,       APPLE_FLAG_FKEY },
+	{ KEY_F10,	KEY_MUTE,           APPLE_FLAG_FKEY },
+	{ KEY_F11,	KEY_VOLUMEDOWN,     APPLE_FLAG_FKEY },
+	{ KEY_F12,	KEY_VOLUMEUP,       APPLE_FLAG_FKEY },
+	{ KEY_UP,	KEY_PAGEUP },
+	{ KEY_DOWN,	KEY_PAGEDOWN },
+	{ KEY_LEFT,	KEY_HOME },
+	{ KEY_RIGHT,	KEY_END },
+	{ }
+};
+
 static const struct apple_key_translation macbookair_fn_keys[] = {
 	{ KEY_BACKSPACE, KEY_DELETE },
 	{ KEY_ENTER,	KEY_INSERT },
@@ -214,7 +236,9 @@
 	}
 
 	if (fnmode) {
-		if (hid->product >= USB_DEVICE_ID_APPLE_WELLSPRING4_ANSI &&
+		if (hid->product == USB_DEVICE_ID_APPLE_MAGIC_KEYBOARD_2021)
+			table = apple2021_fn_keys;
+		else if (hid->product >= USB_DEVICE_ID_APPLE_WELLSPRING4_ANSI &&
 				hid->product <= USB_DEVICE_ID_APPLE_WELLSPRING4A_JIS)
 			table = macbookair_fn_keys;
 		else if (hid->product < 0x21d || hid->product >= 0x300)
@@ -377,6 +401,9 @@
 	for (trans = apple_iso_keyboard; trans->from; trans++)
 		set_bit(trans->to, input->keybit);
 
+	for (trans = apple2021_fn_keys; trans->from; trans++)
+		set_bit(trans->to, input->keybit);
+
 	if (swap_fn_leftctrl) {
 		for (trans = swapped_fn_leftctrl_keys; trans->from; trans++)
 			set_bit(trans->to, input->keybit);
@@ -429,7 +456,7 @@
 
 	if ((asc->quirks & APPLE_HAS_FN) && !asc->fn_found) {
 		hid_info(hdev, "Fn key not found (Apple Wireless Keyboard clone?), disabling Fn key handling\n");
-		asc->quirks = 0;
+		asc->quirks &= ~APPLE_HAS_FN;
 	}
 
 	return 0;
@@ -640,6 +667,10 @@
 		.driver_data = APPLE_NUMLOCK_EMULATION | APPLE_HAS_FN },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY),
 		.driver_data = APPLE_NUMLOCK_EMULATION | APPLE_HAS_FN },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MAGIC_KEYBOARD_2021),
+		.driver_data = APPLE_HAS_FN },
+	{ HID_BLUETOOTH_DEVICE(BT_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MAGIC_KEYBOARD_2021),
+		.driver_data = APPLE_HAS_FN },
 
 	{ }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-appleir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-appleir.c
@@ -188,7 +188,7 @@
 	static const u8 flatbattery[] = { 0x25, 0x87, 0xe0 };
 	unsigned long flags;
 
-	if (len != 5)
+	if (len != 5 || !(hid->claimed & HID_CLAIMED_INPUT))
 		goto out;
 
 	if (!memcmp(data, keydown, sizeof(keydown))) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-asus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-asus.c
@@ -98,6 +98,7 @@
 	struct hid_device *hdev;
 	struct work_struct work;
 	unsigned int brightness;
+	spinlock_t lock;
 	bool removed;
 };
 
@@ -381,7 +382,7 @@
 	return 0;
 }
 
-static int asus_kbd_set_report(struct hid_device *hdev, u8 *buf, size_t buf_size)
+static int asus_kbd_set_report(struct hid_device *hdev, const u8 *buf, size_t buf_size)
 {
 	unsigned char *dmabuf;
 	int ret;
@@ -404,7 +405,7 @@
 
 static int asus_kbd_init(struct hid_device *hdev)
 {
-	u8 buf[] = { FEATURE_KBD_REPORT_ID, 0x41, 0x53, 0x55, 0x53, 0x20, 0x54,
+	const u8 buf[] = { FEATURE_KBD_REPORT_ID, 0x41, 0x53, 0x55, 0x53, 0x20, 0x54,
 		     0x65, 0x63, 0x68, 0x2e, 0x49, 0x6e, 0x63, 0x2e, 0x00 };
 	int ret;
 
@@ -418,7 +419,7 @@
 static int asus_kbd_get_functions(struct hid_device *hdev,
 				  unsigned char *kbd_func)
 {
-	u8 buf[] = { FEATURE_KBD_REPORT_ID, 0x05, 0x20, 0x31, 0x00, 0x08 };
+	const u8 buf[] = { FEATURE_KBD_REPORT_ID, 0x05, 0x20, 0x31, 0x00, 0x08 };
 	u8 *readbuf;
 	int ret;
 
@@ -449,7 +450,7 @@
 
 static int rog_nkey_led_init(struct hid_device *hdev)
 {
-	u8 buf_init_start[] = { FEATURE_KBD_LED_REPORT_ID1, 0xB9 };
+	const u8 buf_init_start[] = { FEATURE_KBD_LED_REPORT_ID1, 0xB9 };
 	u8 buf_init2[] = { FEATURE_KBD_LED_REPORT_ID1, 0x41, 0x53, 0x55, 0x53, 0x20,
 				0x54, 0x65, 0x63, 0x68, 0x2e, 0x49, 0x6e, 0x63, 0x2e, 0x00 };
 	u8 buf_init3[] = { FEATURE_KBD_LED_REPORT_ID1,
@@ -492,21 +493,42 @@
 	return ret;
 }
 
+static void asus_schedule_work(struct asus_kbd_leds *led)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&led->lock, flags);
+	if (!led->removed)
+		schedule_work(&led->work);
+	spin_unlock_irqrestore(&led->lock, flags);
+}
+
 static void asus_kbd_backlight_set(struct led_classdev *led_cdev,
 				   enum led_brightness brightness)
 {
 	struct asus_kbd_leds *led = container_of(led_cdev, struct asus_kbd_leds,
 						 cdev);
+	unsigned long flags;
+
+	spin_lock_irqsave(&led->lock, flags);
 	led->brightness = brightness;
-	schedule_work(&led->work);
+	spin_unlock_irqrestore(&led->lock, flags);
+
+	asus_schedule_work(led);
 }
 
 static enum led_brightness asus_kbd_backlight_get(struct led_classdev *led_cdev)
 {
 	struct asus_kbd_leds *led = container_of(led_cdev, struct asus_kbd_leds,
 						 cdev);
+	enum led_brightness brightness;
+	unsigned long flags;
 
-	return led->brightness;
+	spin_lock_irqsave(&led->lock, flags);
+	brightness = led->brightness;
+	spin_unlock_irqrestore(&led->lock, flags);
+
+	return brightness;
 }
 
 static void asus_kbd_backlight_work(struct work_struct *work)
@@ -514,11 +536,11 @@
 	struct asus_kbd_leds *led = container_of(work, struct asus_kbd_leds, work);
 	u8 buf[] = { FEATURE_KBD_REPORT_ID, 0xba, 0xc5, 0xc4, 0x00 };
 	int ret;
+	unsigned long flags;
 
-	if (led->removed)
-		return;
-
+	spin_lock_irqsave(&led->lock, flags);
 	buf[4] = led->brightness;
+	spin_unlock_irqrestore(&led->lock, flags);
 
 	ret = asus_kbd_set_report(led->hdev, buf, sizeof(buf));
 	if (ret < 0)
@@ -586,6 +608,7 @@
 	drvdata->kbd_backlight->cdev.brightness_set = asus_kbd_backlight_set;
 	drvdata->kbd_backlight->cdev.brightness_get = asus_kbd_backlight_get;
 	INIT_WORK(&drvdata->kbd_backlight->work, asus_kbd_backlight_work);
+	spin_lock_init(&drvdata->kbd_backlight->lock);
 
 	ret = devm_led_classdev_register(&hdev->dev, &drvdata->kbd_backlight->cdev);
 	if (ret < 0) {
@@ -991,6 +1014,24 @@
 	return 0;
 }
 
+static int __maybe_unused asus_resume(struct hid_device *hdev) {
+	struct asus_drvdata *drvdata = hid_get_drvdata(hdev);
+	int ret = 0;
+
+	if (drvdata->kbd_backlight) {
+		const u8 buf[] = { FEATURE_KBD_REPORT_ID, 0xba, 0xc5, 0xc4,
+				drvdata->kbd_backlight->cdev.brightness };
+		ret = asus_kbd_set_report(hdev, buf, sizeof(buf));
+		if (ret < 0) {
+			hid_err(hdev, "Asus failed to set keyboard backlight: %d\n", ret);
+			goto asus_resume_err;
+		}
+	}
+
+asus_resume_err:
+	return ret;
+}
+
 static int __maybe_unused asus_reset_resume(struct hid_device *hdev)
 {
 	struct asus_drvdata *drvdata = hid_get_drvdata(hdev);
@@ -1028,8 +1069,7 @@
 	if (drvdata->quirks & QUIRK_IS_MULTITOUCH)
 		drvdata->tp = &asus_i2c_tp;
 
-	if ((drvdata->quirks & QUIRK_T100_KEYBOARD) &&
-	    hid_is_using_ll_driver(hdev, &usb_hid_driver)) {
+	if ((drvdata->quirks & QUIRK_T100_KEYBOARD) && hid_is_usb(hdev)) {
 		struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
 
 		if (intf->altsetting->desc.bInterfaceNumber == T100_TPAD_INTF) {
@@ -1057,8 +1097,7 @@
 		drvdata->tp = &asus_t100chi_tp;
 	}
 
-	if ((drvdata->quirks & QUIRK_MEDION_E1239T) &&
-	    hid_is_using_ll_driver(hdev, &usb_hid_driver)) {
+	if ((drvdata->quirks & QUIRK_MEDION_E1239T) && hid_is_usb(hdev)) {
 		struct usb_host_interface *alt =
 			to_usb_interface(hdev->dev.parent)->altsetting;
 
@@ -1123,9 +1162,13 @@
 static void asus_remove(struct hid_device *hdev)
 {
 	struct asus_drvdata *drvdata = hid_get_drvdata(hdev);
+	unsigned long flags;
 
 	if (drvdata->kbd_backlight) {
+		spin_lock_irqsave(&drvdata->kbd_backlight->lock, flags);
 		drvdata->kbd_backlight->removed = true;
+		spin_unlock_irqrestore(&drvdata->kbd_backlight->lock, flags);
+
 		cancel_work_sync(&drvdata->kbd_backlight->work);
 	}
 
@@ -1214,6 +1257,13 @@
 		rdesc = new_rdesc;
 	}
 
+	if (drvdata->quirks & QUIRK_ROG_NKEY_KEYBOARD &&
+			*rsize == 331 && rdesc[190] == 0x85 && rdesc[191] == 0x5a &&
+			rdesc[204] == 0x95 && rdesc[205] == 0x05) {
+		hid_info(hdev, "Fixing up Asus N-KEY keyb report descriptor\n");
+		rdesc[205] = 0x01;
+	}
+
 	return rdesc;
 }
 
@@ -1273,6 +1323,7 @@
 	.input_configured       = asus_input_configured,
 #ifdef CONFIG_PM
 	.reset_resume           = asus_reset_resume,
+	.resume					= asus_resume,
 #endif
 	.event			= asus_event,
 	.raw_event		= asus_raw_event
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-betopff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-betopff.c
@@ -60,7 +60,6 @@
 	struct list_head *report_list =
 			&hid->report_enum[HID_OUTPUT_REPORT].report_list;
 	struct input_dev *dev;
-	int field_count = 0;
 	int error;
 	int i, j;
 
@@ -86,19 +85,21 @@
 	 * -----------------------------------------
 	 * Do init them with default value.
 	 */
+	if (report->maxfield < 4) {
+		hid_err(hid, "not enough fields in the report: %d\n",
+				report->maxfield);
+		return -ENODEV;
+	}
 	for (i = 0; i < report->maxfield; i++) {
+		if (report->field[i]->report_count < 1) {
+			hid_err(hid, "no values in the field\n");
+			return -ENODEV;
+		}
 		for (j = 0; j < report->field[i]->report_count; j++) {
 			report->field[i]->value[j] = 0x00;
-			field_count++;
 		}
 	}
 
-	if (field_count < 4) {
-		hid_err(hid, "not enough fields in the report: %d\n",
-				field_count);
-		return -ENODEV;
-	}
-
 	betopff = kzalloc(sizeof(*betopff), GFP_KERNEL);
 	if (!betopff)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-bigbenff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-bigbenff.c
@@ -174,6 +174,7 @@
 struct bigben_device {
 	struct hid_device *hid;
 	struct hid_report *report;
+	spinlock_t lock;
 	bool removed;
 	u8 led_state;         /* LED1 = 1 .. LED4 = 8 */
 	u8 right_motor_on;    /* right motor off/on 0/1 */
@@ -184,18 +185,39 @@
 	struct work_struct worker;
 };
 
+static inline void bigben_schedule_work(struct bigben_device *bigben)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&bigben->lock, flags);
+	if (!bigben->removed)
+		schedule_work(&bigben->worker);
+	spin_unlock_irqrestore(&bigben->lock, flags);
+}
 
 static void bigben_worker(struct work_struct *work)
 {
 	struct bigben_device *bigben = container_of(work,
 		struct bigben_device, worker);
 	struct hid_field *report_field = bigben->report->field[0];
+	bool do_work_led = false;
+	bool do_work_ff = false;
+	u8 *buf;
+	u32 len;
+	unsigned long flags;
 
-	if (bigben->removed)
+	buf = hid_alloc_report_buf(bigben->report, GFP_KERNEL);
+	if (!buf)
 		return;
 
+	len = hid_report_len(bigben->report);
+
+	/* LED work */
+	spin_lock_irqsave(&bigben->lock, flags);
+
 	if (bigben->work_led) {
 		bigben->work_led = false;
+		do_work_led = true;
 		report_field->value[0] = 0x01; /* 1 = led message */
 		report_field->value[1] = 0x08; /* reserved value, always 8 */
 		report_field->value[2] = bigben->led_state;
@@ -204,11 +226,22 @@
 		report_field->value[5] = 0x00; /* padding */
 		report_field->value[6] = 0x00; /* padding */
 		report_field->value[7] = 0x00; /* padding */
-		hid_hw_request(bigben->hid, bigben->report, HID_REQ_SET_REPORT);
+		hid_output_report(bigben->report, buf);
 	}
 
+	spin_unlock_irqrestore(&bigben->lock, flags);
+
+	if (do_work_led) {
+		hid_hw_raw_request(bigben->hid, bigben->report->id, buf, len,
+				   bigben->report->type, HID_REQ_SET_REPORT);
+	}
+
+	/* FF work */
+	spin_lock_irqsave(&bigben->lock, flags);
+
 	if (bigben->work_ff) {
 		bigben->work_ff = false;
+		do_work_ff = true;
 		report_field->value[0] = 0x02; /* 2 = rumble effect message */
 		report_field->value[1] = 0x08; /* reserved value, always 8 */
 		report_field->value[2] = bigben->right_motor_on;
@@ -217,8 +250,17 @@
 		report_field->value[5] = 0x00; /* padding */
 		report_field->value[6] = 0x00; /* padding */
 		report_field->value[7] = 0x00; /* padding */
-		hid_hw_request(bigben->hid, bigben->report, HID_REQ_SET_REPORT);
+		hid_output_report(bigben->report, buf);
+	}
+
+	spin_unlock_irqrestore(&bigben->lock, flags);
+
+	if (do_work_ff) {
+		hid_hw_raw_request(bigben->hid, bigben->report->id, buf, len,
+				   bigben->report->type, HID_REQ_SET_REPORT);
 	}
+
+	kfree(buf);
 }
 
 static int hid_bigben_play_effect(struct input_dev *dev, void *data,
@@ -228,6 +270,7 @@
 	struct bigben_device *bigben = hid_get_drvdata(hid);
 	u8 right_motor_on;
 	u8 left_motor_force;
+	unsigned long flags;
 
 	if (!bigben) {
 		hid_err(hid, "no device data\n");
@@ -242,10 +285,13 @@
 
 	if (right_motor_on != bigben->right_motor_on ||
 			left_motor_force != bigben->left_motor_force) {
+		spin_lock_irqsave(&bigben->lock, flags);
 		bigben->right_motor_on   = right_motor_on;
 		bigben->left_motor_force = left_motor_force;
 		bigben->work_ff = true;
-		schedule_work(&bigben->worker);
+		spin_unlock_irqrestore(&bigben->lock, flags);
+
+		bigben_schedule_work(bigben);
 	}
 
 	return 0;
@@ -259,6 +305,7 @@
 	struct bigben_device *bigben = hid_get_drvdata(hid);
 	int n;
 	bool work;
+	unsigned long flags;
 
 	if (!bigben) {
 		hid_err(hid, "no device data\n");
@@ -267,6 +314,7 @@
 
 	for (n = 0; n < NUM_LEDS; n++) {
 		if (led == bigben->leds[n]) {
+			spin_lock_irqsave(&bigben->lock, flags);
 			if (value == LED_OFF) {
 				work = (bigben->led_state & BIT(n));
 				bigben->led_state &= ~BIT(n);
@@ -274,10 +322,11 @@
 				work = !(bigben->led_state & BIT(n));
 				bigben->led_state |= BIT(n);
 			}
+			spin_unlock_irqrestore(&bigben->lock, flags);
 
 			if (work) {
 				bigben->work_led = true;
-				schedule_work(&bigben->worker);
+				bigben_schedule_work(bigben);
 			}
 			return;
 		}
@@ -307,8 +356,12 @@
 static void bigben_remove(struct hid_device *hid)
 {
 	struct bigben_device *bigben = hid_get_drvdata(hid);
+	unsigned long flags;
 
+	spin_lock_irqsave(&bigben->lock, flags);
 	bigben->removed = true;
+	spin_unlock_irqrestore(&bigben->lock, flags);
+
 	cancel_work_sync(&bigben->worker);
 	hid_hw_stop(hid);
 }
@@ -318,7 +371,6 @@
 {
 	struct bigben_device *bigben;
 	struct hid_input *hidinput;
-	struct list_head *report_list;
 	struct led_classdev *led;
 	char *name;
 	size_t name_sz;
@@ -343,14 +395,24 @@
 		return error;
 	}
 
-	report_list = &hid->report_enum[HID_OUTPUT_REPORT].report_list;
-	bigben->report = list_entry(report_list->next,
-		struct hid_report, list);
+	bigben->report = hid_validate_values(hid, HID_OUTPUT_REPORT, 0, 0, 8);
+	if (!bigben->report) {
+		hid_err(hid, "no output report found\n");
+		error = -ENODEV;
+		goto error_hw_stop;
+	}
+
+	if (list_empty(&hid->inputs)) {
+		hid_err(hid, "no inputs found\n");
+		error = -ENODEV;
+		goto error_hw_stop;
+	}
 
 	hidinput = list_first_entry(&hid->inputs, struct hid_input, list);
 	set_bit(FF_RUMBLE, hidinput->input->ffbit);
 
 	INIT_WORK(&bigben->worker, bigben_worker);
+	spin_lock_init(&bigben->lock);
 
 	error = input_ff_create_memless(hidinput->input, NULL,
 		hid_bigben_play_effect);
@@ -391,7 +453,7 @@
 	bigben->left_motor_force = 0;
 	bigben->work_led = true;
 	bigben->work_ff = true;
-	schedule_work(&bigben->worker);
+	bigben_schedule_work(bigben);
 
 	hid_info(hid, "LED and force feedback support for BigBen gamepad\n");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-chicony.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-chicony.c
@@ -114,6 +114,9 @@
 {
 	int ret;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	hdev->quirks |= HID_QUIRK_INPUT_PER_APP;
 	ret = hid_parse(hdev);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-core.c
@@ -258,6 +258,7 @@
 {
 	struct hid_report *report;
 	struct hid_field *field;
+	unsigned int max_buffer_size = HID_MAX_BUFFER_SIZE;
 	unsigned int usages;
 	unsigned int offset;
 	unsigned int i;
@@ -288,8 +289,11 @@
 	offset = report->size;
 	report->size += parser->global.report_size * parser->global.report_count;
 
+	if (parser->device->ll_driver->max_buffer_size)
+		max_buffer_size = parser->device->ll_driver->max_buffer_size;
+
 	/* Total size check: Allow for possible report index byte */
-	if (report->size > (HID_MAX_BUFFER_SIZE - 1) << 3) {
+	if (report->size > (max_buffer_size - 1) << 3) {
 		hid_err(parser->device, "report is too long\n");
 		return -1;
 	}
@@ -698,15 +702,22 @@
  * Free a device structure, all reports, and all fields.
  */
 
-static void hid_device_release(struct device *dev)
+void hiddev_free(struct kref *ref)
 {
-	struct hid_device *hid = to_hid_device(dev);
+	struct hid_device *hid = container_of(ref, struct hid_device, ref);
 
 	hid_close_report(hid);
 	kfree(hid->dev_rdesc);
 	kfree(hid);
 }
 
+static void hid_device_release(struct device *dev)
+{
+	struct hid_device *hid = to_hid_device(dev);
+
+	kref_put(&hid->ref, hiddev_free);
+}
+
 /*
  * Fetch a report description item from the data stream. We support long
  * items, though they are not used yet.
@@ -988,8 +999,8 @@
 		 * Validating on id 0 means we should examine the first
 		 * report in the list.
 		 */
-		report = list_entry(
-				hid->report_enum[type].report_list.next,
+		report = list_first_entry_or_null(
+				&hid->report_enum[type].report_list,
 				struct hid_report, list);
 	} else {
 		report = hid->report_enum[type].report_id_hash[id];
@@ -1113,6 +1124,8 @@
 	while (multiplier_collection->parent_idx != -1 &&
 	       multiplier_collection->type != HID_COLLECTION_LOGICAL)
 		multiplier_collection = &hid->collection[multiplier_collection->parent_idx];
+	if (multiplier_collection->type != HID_COLLECTION_LOGICAL)
+		multiplier_collection = NULL;
 
 	effective_multiplier = hid_calculate_multiplier(hid, multiplier);
 
@@ -1197,6 +1210,7 @@
 	__u8 *end;
 	__u8 *next;
 	int ret;
+	int i;
 	static int (*dispatch_type[])(struct hid_parser *parser,
 				      struct hid_item *item) = {
 		hid_parser_main,
@@ -1247,6 +1261,8 @@
 		goto err;
 	}
 	device->collection_size = HID_DEFAULT_NUM_COLLECTIONS;
+	for (i = 0; i < HID_DEFAULT_NUM_COLLECTIONS; i++)
+		device->collection[i].parent_idx = -1;
 
 	ret = -EINVAL;
 	while ((next = fetch_item(start, end, &item)) != NULL) {
@@ -1310,6 +1326,9 @@
 	if (!value || !n)
 		return 0;
 
+	if (n > 32)
+		n = 32;
+
 	switch (n) {
 	case 8:  return ((__s8)value);
 	case 16: return ((__s16)value);
@@ -1429,7 +1448,6 @@
 			hid_warn(hid,
 				 "%s() called with too large value %d (n: %d)! (%s)\n",
 				 __func__, value, n, current->comm);
-			WARN_ON(1);
 			value &= m;
 		}
 	}
@@ -1648,7 +1666,7 @@
 
 	u32 len = hid_report_len(report) + 7;
 
-	return kmalloc(len, flags);
+	return kzalloc(len, flags);
 }
 EXPORT_SYMBOL_GPL(hid_alloc_report_buf);
 
@@ -1746,6 +1764,7 @@
 	struct hid_report_enum *report_enum = hid->report_enum + type;
 	struct hid_report *report;
 	struct hid_driver *hdrv;
+	int max_buffer_size = HID_MAX_BUFFER_SIZE;
 	unsigned int a;
 	u32 rsize, csize = size;
 	u8 *cdata = data;
@@ -1762,10 +1781,13 @@
 
 	rsize = hid_compute_report_size(report);
 
-	if (report_enum->numbered && rsize >= HID_MAX_BUFFER_SIZE)
-		rsize = HID_MAX_BUFFER_SIZE - 1;
-	else if (rsize > HID_MAX_BUFFER_SIZE)
-		rsize = HID_MAX_BUFFER_SIZE;
+	if (hid->ll_driver->max_buffer_size)
+		max_buffer_size = hid->ll_driver->max_buffer_size;
+
+	if (report_enum->numbered && rsize >= max_buffer_size)
+		rsize = max_buffer_size - 1;
+	else if (rsize > max_buffer_size)
+		rsize = max_buffer_size;
 
 	if (csize < rsize) {
 		dbg_hid("report %d is too short, (%d < %d)\n", report->id,
@@ -2428,10 +2450,12 @@
 			hid_warn(hdev, "bad device descriptor (%d)\n", ret);
 	}
 
+	hdev->id = atomic_inc_return(&id);
+
 	/* XXX hack, any other cleaner solution after the driver core
 	 * is converted to allow more than 20 bytes as the device name? */
 	dev_set_name(&hdev->dev, "%04X:%04X:%04X.%04X", hdev->bus,
-		     hdev->vendor, hdev->product, atomic_inc_return(&id));
+		     hdev->vendor, hdev->product, hdev->id);
 
 	hid_debug_register(hdev, dev_name(&hdev->dev));
 	ret = device_add(&hdev->dev);
@@ -2474,6 +2498,7 @@
 	spin_lock_init(&hdev->debug_list_lock);
 	sema_init(&hdev->driver_input_lock, 1);
 	mutex_init(&hdev->ll_open_lock);
+	kref_init(&hdev->ref);
 
 	return hdev;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-corsair.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-corsair.c
@@ -553,7 +553,12 @@
 	int ret;
 	unsigned long quirks = id->driver_data;
 	struct corsair_drvdata *drvdata;
-	struct usb_interface *usbif = to_usb_interface(dev->dev.parent);
+	struct usb_interface *usbif;
+
+	if (!hid_is_usb(dev))
+		return -EINVAL;
+
+	usbif = to_usb_interface(dev->dev.parent);
 
 	drvdata = devm_kzalloc(&dev->dev, sizeof(struct corsair_drvdata),
 			       GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-cougar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-cougar.c
@@ -106,7 +106,7 @@
 static __u8 *cougar_report_fixup(struct hid_device *hdev, __u8 *rdesc,
 				 unsigned int *rsize)
 {
-	if (rdesc[2] == 0x09 && rdesc[3] == 0x02 &&
+	if (*rsize >= 117 && rdesc[2] == 0x09 && rdesc[3] == 0x02 &&
 	    (rdesc[115] | rdesc[116] << 8) >= HID_MAX_USAGES) {
 		hid_info(hdev,
 			"usage count exceeds max: fixing up report descriptor\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-cp2112.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-cp2112.c
@@ -788,6 +788,11 @@
 		data->word = le16_to_cpup((__le16 *)buf);
 		break;
 	case I2C_SMBUS_I2C_BLOCK_DATA:
+		if (read_length > I2C_SMBUS_BLOCK_MAX) {
+			ret = -EINVAL;
+			goto power_normal;
+		}
+
 		memcpy(data->block + 1, buf, read_length);
 		break;
 	case I2C_SMBUS_BLOCK_DATA:
@@ -1152,8 +1157,6 @@
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 	struct cp2112_device *dev = gpiochip_get_data(gc);
 
-	INIT_DELAYED_WORK(&dev->gpio_poll_worker, cp2112_gpio_poll_callback);
-
 	if (!dev->gpio_poll) {
 		dev->gpio_poll = true;
 		schedule_delayed_work(&dev->gpio_poll_worker, 0);
@@ -1168,7 +1171,10 @@
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 	struct cp2112_device *dev = gpiochip_get_data(gc);
 
-	cancel_delayed_work_sync(&dev->gpio_poll_worker);
+	if (!dev->irq_mask) {
+		dev->gpio_poll = false;
+		cancel_delayed_work_sync(&dev->gpio_poll_worker);
+	}
 }
 
 static int cp2112_gpio_irq_type(struct irq_data *d, unsigned int type)
@@ -1347,6 +1353,9 @@
 	girq->parents = NULL;
 	girq->default_type = IRQ_TYPE_NONE;
 	girq->handler = handle_simple_irq;
+	girq->threaded = true;
+
+	INIT_DELAYED_WORK(&dev->gpio_poll_worker, cp2112_gpio_poll_callback);
 
 	ret = gpiochip_add_data(&dev->gc, dev);
 	if (ret < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-debug.c
@@ -825,7 +825,9 @@
 	[KEY_F22] = "F22",			[KEY_F23] = "F23",
 	[KEY_F24] = "F24",			[KEY_PLAYCD] = "PlayCD",
 	[KEY_PAUSECD] = "PauseCD",		[KEY_PROG3] = "Prog3",
-	[KEY_PROG4] = "Prog4",			[KEY_SUSPEND] = "Suspend",
+	[KEY_PROG4] = "Prog4",
+	[KEY_ALL_APPLICATIONS] = "AllApplications",
+	[KEY_SUSPEND] = "Suspend",
 	[KEY_CLOSE] = "Close",			[KEY_PLAY] = "Play",
 	[KEY_FASTFORWARD] = "FastForward",	[KEY_BASSBOOST] = "BassBoost",
 	[KEY_PRINT] = "Print",			[KEY_HP] = "HP",
@@ -934,6 +936,8 @@
 	[KEY_ASSISTANT] = "Assistant",
 	[KEY_KBD_LAYOUT_NEXT] = "KbdLayoutNext",
 	[KEY_EMOJI_PICKER] = "EmojiPicker",
+	[KEY_DICTATE] = "Dictate",
+	[KEY_MICMUTE] = "MicrophoneMute",
 	[KEY_BRIGHTNESS_MIN] = "BrightnessMin",
 	[KEY_BRIGHTNESS_MAX] = "BrightnessMax",
 	[KEY_BRIGHTNESS_AUTO] = "BrightnessAuto",
@@ -1092,6 +1096,7 @@
 		goto out;
 	}
 	list->hdev = (struct hid_device *) inode->i_private;
+	kref_get(&list->hdev->ref);
 	file->private_data = list;
 	mutex_init(&list->read_mutex);
 
@@ -1184,6 +1189,8 @@
 	list_del(&list->node);
 	spin_unlock_irqrestore(&list->hdev->debug_list_lock, flags);
 	kfifo_free(&list->hid_debug_fifo);
+
+	kref_put(&list->hdev->ref, hiddev_free);
 	kfree(list);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-elan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-elan.c
@@ -50,7 +50,7 @@
 
 static int is_not_elan_touchpad(struct hid_device *hdev)
 {
-	if (hdev->bus == BUS_USB) {
+	if (hid_is_usb(hdev)) {
 		struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
 
 		return (intf->altsetting->desc.bInterfaceNumber !=
@@ -188,7 +188,6 @@
 	ret = input_mt_init_slots(input, ELAN_MAX_FINGERS, INPUT_MT_POINTER);
 	if (ret) {
 		hid_err(hdev, "Failed to init elan MT slots: %d\n", ret);
-		input_free_device(input);
 		return ret;
 	}
 
@@ -200,7 +199,6 @@
 		hid_err(hdev, "Failed to register elan input device: %d\n",
 			ret);
 		input_mt_destroy_slots(input);
-		input_free_device(input);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-elecom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-elecom.c
@@ -12,6 +12,7 @@
  *  Copyright (c) 2017 Alex Manoussakis <amanou@gnu.org>
  *  Copyright (c) 2017 Tomasz Kramkowski <tk@the-tk.com>
  *  Copyright (c) 2020 YOSHIOKA Takuma <lo48576@hard-wi.red>
+ *  Copyright (c) 2022 Takahiro Fujii <fujii@xaxxi.net>
  */
 
 /*
@@ -89,7 +90,7 @@
 	case USB_DEVICE_ID_ELECOM_M_DT1URBK:
 	case USB_DEVICE_ID_ELECOM_M_DT1DRBK:
 	case USB_DEVICE_ID_ELECOM_M_HT1URBK:
-	case USB_DEVICE_ID_ELECOM_M_HT1DRBK:
+	case USB_DEVICE_ID_ELECOM_M_HT1DRBK_010D:
 		/*
 		 * Report descriptor format:
 		 * 12: button bit count
@@ -99,6 +100,16 @@
 		 */
 		mouse_button_fixup(hdev, rdesc, *rsize, 12, 30, 14, 20, 8);
 		break;
+	case USB_DEVICE_ID_ELECOM_M_HT1DRBK_011C:
+		/*
+		 * Report descriptor format:
+		 * 22: button bit count
+		 * 30: padding bit count
+		 * 24: button report size
+		 * 16: button usage maximum
+		 */
+		mouse_button_fixup(hdev, rdesc, *rsize, 22, 30, 24, 16, 8);
+		break;
 	}
 	return rdesc;
 }
@@ -112,7 +123,8 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_DT1URBK) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_DT1DRBK) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1URBK) },
-	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1DRBK) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1DRBK_010D) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1DRBK_011C) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, elecom_devices);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-elo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-elo.c
@@ -228,15 +228,16 @@
 {
 	struct elo_priv *priv;
 	int ret;
-	struct usb_device *udev;
+
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
 
 	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
 
 	INIT_DELAYED_WORK(&priv->work, elo_work);
-	udev = interface_to_usbdev(to_usb_interface(hdev->dev.parent));
-	priv->usbdev = usb_get_dev(udev);
+	priv->usbdev = interface_to_usbdev(to_usb_interface(hdev->dev.parent));
 
 	hid_set_drvdata(hdev, priv);
 
@@ -267,8 +268,6 @@
 {
 	struct elo_priv *priv = hid_get_drvdata(hdev);
 
-	usb_put_dev(priv->usbdev);
-
 	hid_hw_stop(hdev);
 	cancel_delayed_work_sync(&priv->work);
 	kfree(priv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-ft260.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-ft260.c
@@ -915,6 +915,9 @@
 	struct ft260_get_chip_version_report version;
 	int ret;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	dev = devm_kzalloc(&hdev->dev, sizeof(*dev), GFP_KERNEL);
 	if (!dev)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-glorious.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-glorious.c
@@ -21,6 +21,10 @@
  * Glorious Model O and O- specify the const flag in the consumer input
  * report descriptor, which leads to inputs being ignored. Fix this
  * by patching the descriptor.
+ *
+ * Glorious Model I incorrectly specifes the Usage Minimum for its
+ * keyboard HID report, causing keycodes to be misinterpreted.
+ * Fix this by setting Usage Minimum to 0 in that report.
  */
 static __u8 *glorious_report_fixup(struct hid_device *hdev, __u8 *rdesc,
 		unsigned int *rsize)
@@ -32,6 +36,10 @@
 		rdesc[85] = rdesc[113] = rdesc[141] = \
 			HID_MAIN_ITEM_VARIABLE | HID_MAIN_ITEM_RELATIVE;
 	}
+	if (*rsize == 156 && rdesc[41] == 1) {
+		hid_info(hdev, "patching Glorious Model I keyboard report descriptor\n");
+		rdesc[41] = 0;
+	}
 	return rdesc;
 }
 
@@ -44,6 +52,8 @@
 		model = "Model O"; break;
 	case USB_DEVICE_ID_GLORIOUS_MODEL_D:
 		model = "Model D"; break;
+	case USB_DEVICE_ID_GLORIOUS_MODEL_I:
+		model = "Model I"; break;
 	}
 
 	snprintf(hdev->name, sizeof(hdev->name), "%s %s", "Glorious", model);
@@ -66,10 +76,12 @@
 }
 
 static const struct hid_device_id glorious_devices[] = {
-	{ HID_USB_DEVICE(USB_VENDOR_ID_GLORIOUS,
+	{ HID_USB_DEVICE(USB_VENDOR_ID_SINOWEALTH,
 		USB_DEVICE_ID_GLORIOUS_MODEL_O) },
-	{ HID_USB_DEVICE(USB_VENDOR_ID_GLORIOUS,
+	{ HID_USB_DEVICE(USB_VENDOR_ID_SINOWEALTH,
 		USB_DEVICE_ID_GLORIOUS_MODEL_D) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_LAVIEW,
+		USB_DEVICE_ID_GLORIOUS_MODEL_I) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, glorious_devices);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-google-hammer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-google-hammer.c
@@ -267,11 +267,13 @@
 	return 0;
 }
 
+#ifdef CONFIG_ACPI
 static const struct acpi_device_id cbas_ec_acpi_ids[] = {
 	{ "GOOG000B", 0 },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, cbas_ec_acpi_ids);
+#endif
 
 #ifdef CONFIG_OF
 static const struct of_device_id cbas_ec_of_match[] = {
@@ -586,8 +588,12 @@
 	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
 		     USB_VENDOR_ID_GOOGLE, USB_DEVICE_ID_GOOGLE_DON) },
 	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
+		     USB_VENDOR_ID_GOOGLE, USB_DEVICE_ID_GOOGLE_EEL) },
+	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
 		     USB_VENDOR_ID_GOOGLE, USB_DEVICE_ID_GOOGLE_HAMMER) },
 	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
+		     USB_VENDOR_ID_GOOGLE, USB_DEVICE_ID_GOOGLE_JEWEL) },
+	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
 		     USB_VENDOR_ID_GOOGLE, USB_DEVICE_ID_GOOGLE_MAGNEMITE) },
 	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
 		     USB_VENDOR_ID_GOOGLE, USB_DEVICE_ID_GOOGLE_MASTERBALL) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-holtek-kbd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-holtek-kbd.c
@@ -130,6 +130,10 @@
 		return -ENODEV;
 
 	boot_hid = usb_get_intfdata(boot_interface);
+	if (list_empty(&boot_hid->inputs)) {
+		hid_err(hid, "no inputs found\n");
+		return -ENODEV;
+	}
 	boot_hid_input = list_first_entry(&boot_hid->inputs,
 		struct hid_input, list);
 
@@ -140,12 +144,17 @@
 static int holtek_kbd_probe(struct hid_device *hdev,
 		const struct hid_device_id *id)
 {
-	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
-	int ret = hid_parse(hdev);
+	struct usb_interface *intf;
+	int ret;
+
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
 
+	ret = hid_parse(hdev);
 	if (!ret)
 		ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
 
+	intf = to_usb_interface(hdev->dev.parent);
 	if (!ret && intf->cur_altsetting->desc.bInterfaceNumber == 1) {
 		struct hid_input *hidinput;
 		list_for_each_entry(hidinput, &hdev->inputs, list) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-holtek-mouse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-holtek-mouse.c
@@ -62,6 +62,29 @@
 	return rdesc;
 }
 
+static int holtek_mouse_probe(struct hid_device *hdev,
+			      const struct hid_device_id *id)
+{
+	int ret;
+
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
+	ret = hid_parse(hdev);
+	if (ret) {
+		hid_err(hdev, "hid parse failed: %d\n", ret);
+		return ret;
+	}
+
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (ret) {
+		hid_err(hdev, "hw start failed: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
 static const struct hid_device_id holtek_mouse_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT,
 			USB_DEVICE_ID_HOLTEK_ALT_MOUSE_A067) },
@@ -83,6 +106,7 @@
 	.name = "holtek_mouse",
 	.id_table = holtek_mouse_devices,
 	.report_fixup = holtek_mouse_report_fixup,
+	.probe = holtek_mouse_probe,
 };
 
 module_hid_driver(holtek_mouse_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-hyperv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-hyperv.c
@@ -498,7 +498,7 @@
 
 	ret = hid_add_device(hid_dev);
 	if (ret)
-		goto probe_err1;
+		goto probe_err2;
 
 
 	ret = hid_parse(hid_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-ids.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-ids.h
@@ -174,6 +174,7 @@
 #define USB_DEVICE_ID_APPLE_IRCONTROL3	0x8241
 #define USB_DEVICE_ID_APPLE_IRCONTROL4	0x8242
 #define USB_DEVICE_ID_APPLE_IRCONTROL5	0x8243
+#define USB_DEVICE_ID_APPLE_MAGIC_KEYBOARD_2021   0x029c
 
 #define USB_VENDOR_ID_ASUS		0x0486
 #define USB_DEVICE_ID_ASUS_T91MT	0x0185
@@ -349,6 +350,7 @@
 
 #define USB_VENDOR_ID_DELL				0x413c
 #define USB_DEVICE_ID_DELL_PIXART_USB_OPTICAL_MOUSE	0x301a
+#define USB_DEVICE_ID_DELL_PRO_WIRELESS_KM5221W		0x4503
 
 #define USB_VENDOR_ID_DELORME		0x1163
 #define USB_DEVICE_ID_DELORME_EARTHMATE	0x0100
@@ -394,8 +396,12 @@
 #define USB_DEVICE_ID_HP_X2		0x074d
 #define USB_DEVICE_ID_HP_X2_10_COVER	0x0755
 #define I2C_DEVICE_ID_HP_SPECTRE_X360_15	0x2817
+#define I2C_DEVICE_ID_HP_ENVY_X360_15T_DR100	0x29CF
+#define USB_DEVICE_ID_ASUS_UX550VE_TOUCHSCREEN	0x2544
 #define USB_DEVICE_ID_ASUS_UX550_TOUCHSCREEN	0x2706
 #define I2C_DEVICE_ID_SURFACE_GO_TOUCHSCREEN	0x261A
+#define I2C_DEVICE_ID_SURFACE_GO2_TOUCHSCREEN	0x2A1C
+#define I2C_DEVICE_ID_LENOVO_YOGA_C630_TOUCHSCREEN	0x279F
 
 #define USB_VENDOR_ID_ELECOM		0x056e
 #define USB_DEVICE_ID_ELECOM_BM084	0x0061
@@ -406,7 +412,8 @@
 #define USB_DEVICE_ID_ELECOM_M_DT1URBK	0x00fe
 #define USB_DEVICE_ID_ELECOM_M_DT1DRBK	0x00ff
 #define USB_DEVICE_ID_ELECOM_M_HT1URBK	0x010c
-#define USB_DEVICE_ID_ELECOM_M_HT1DRBK	0x010d
+#define USB_DEVICE_ID_ELECOM_M_HT1DRBK_010D	0x010d
+#define USB_DEVICE_ID_ELECOM_M_HT1DRBK_011C	0x011c
 
 #define USB_VENDOR_ID_DREAM_CHEEKY	0x1d34
 #define USB_DEVICE_ID_DREAM_CHEEKY_WN	0x0004
@@ -476,11 +483,9 @@
 #define USB_DEVICE_ID_GENERAL_TOUCH_WIN8_PIT_010A 0x010a
 #define USB_DEVICE_ID_GENERAL_TOUCH_WIN8_PIT_E100 0xe100
 
-#define USB_VENDOR_ID_GLORIOUS  0x258a
-#define USB_DEVICE_ID_GLORIOUS_MODEL_D 0x0033
-#define USB_DEVICE_ID_GLORIOUS_MODEL_O 0x0036
-
 #define I2C_VENDOR_ID_GOODIX		0x27c6
+#define I2C_DEVICE_ID_GOODIX_01E8	0x01e8
+#define I2C_DEVICE_ID_GOODIX_01E9	0x01e9
 #define I2C_DEVICE_ID_GOODIX_01F0	0x01f0
 
 #define USB_VENDOR_ID_GOODTOUCH		0x1aad
@@ -496,6 +501,8 @@
 #define USB_DEVICE_ID_GOOGLE_MAGNEMITE	0x503d
 #define USB_DEVICE_ID_GOOGLE_MOONBALL	0x5044
 #define USB_DEVICE_ID_GOOGLE_DON	0x5050
+#define USB_DEVICE_ID_GOOGLE_EEL	0x5057
+#define USB_DEVICE_ID_GOOGLE_JEWEL	0x5061
 
 #define USB_VENDOR_ID_GOTOP		0x08f2
 #define USB_DEVICE_ID_SUPER_Q2		0x007f
@@ -586,6 +593,7 @@
 #define USB_DEVICE_ID_UGCI_FIGHTING	0x0030
 
 #define USB_VENDOR_ID_HP		0x03f0
+#define USB_PRODUCT_ID_HP_ELITE_PRESENTER_MOUSE_464A		0x464a
 #define USB_PRODUCT_ID_HP_LOGITECH_OEM_USB_OPTICAL_MOUSE_0A4A	0x0a4a
 #define USB_PRODUCT_ID_HP_LOGITECH_OEM_USB_OPTICAL_MOUSE_0B4A	0x0b4a
 #define USB_PRODUCT_ID_HP_PIXART_OEM_USB_OPTICAL_MOUSE		0x134a
@@ -699,6 +707,9 @@
 #define USB_VENDOR_ID_LABTEC		0x1020
 #define USB_DEVICE_ID_LABTEC_WIRELESS_KEYBOARD	0x0006
 
+#define USB_VENDOR_ID_LAVIEW		0x22D4
+#define USB_DEVICE_ID_GLORIOUS_MODEL_I	0x1503
+
 #define USB_VENDOR_ID_LCPOWER		0x1241
 #define USB_DEVICE_ID_LCPOWER_LC1000	0xf767
 
@@ -750,6 +761,8 @@
 #define USB_DEVICE_ID_LENOVO_X1_COVER	0x6085
 #define USB_DEVICE_ID_LENOVO_X1_TAB	0x60a3
 #define USB_DEVICE_ID_LENOVO_X1_TAB3	0x60b5
+#define USB_DEVICE_ID_LENOVO_X12_TAB	0x60fe
+#define USB_DEVICE_ID_LENOVO_X12_TAB2	0x61ae
 #define USB_DEVICE_ID_LENOVO_OPTICAL_USB_MOUSE_600E	0x600e
 #define USB_DEVICE_ID_LENOVO_PIXART_USB_MOUSE_608D	0x608d
 #define USB_DEVICE_ID_LENOVO_PIXART_USB_MOUSE_6019	0x6019
@@ -767,6 +780,7 @@
 #define USB_DEVICE_ID_LOGITECH_AUDIOHUB 0x0a0e
 #define USB_DEVICE_ID_LOGITECH_T651	0xb00c
 #define USB_DEVICE_ID_LOGITECH_DINOVO_EDGE_KBD	0xb309
+#define USB_DEVICE_ID_LOGITECH_CASA_TOUCHPAD	0xbb00
 #define USB_DEVICE_ID_LOGITECH_C007	0xc007
 #define USB_DEVICE_ID_LOGITECH_C077	0xc077
 #define USB_DEVICE_ID_LOGITECH_RECEIVER	0xc101
@@ -817,6 +831,7 @@
 #define USB_DEVICE_ID_LOGITECH_NANO_RECEIVER_LIGHTSPEED_1	0xc539
 #define USB_DEVICE_ID_LOGITECH_NANO_RECEIVER_LIGHTSPEED_1_1	0xc53f
 #define USB_DEVICE_ID_LOGITECH_NANO_RECEIVER_POWERPLAY	0xc53a
+#define USB_DEVICE_ID_LOGITECH_BOLT_RECEIVER	0xc548
 #define USB_DEVICE_ID_SPACETRAVELLER	0xc623
 #define USB_DEVICE_ID_SPACENAVIGATOR	0xc626
 #define USB_DEVICE_ID_DINOVO_DESKTOP	0xc704
@@ -839,6 +854,7 @@
 #define USB_DEVICE_ID_MADCATZ_BEATPAD	0x4540
 #define USB_DEVICE_ID_MADCATZ_RAT5	0x1705
 #define USB_DEVICE_ID_MADCATZ_RAT9	0x1709
+#define USB_DEVICE_ID_MADCATZ_MMO7  0x1713
 
 #define USB_VENDOR_ID_MCC		0x09db
 #define USB_DEVICE_ID_MCC_PMD1024LS	0x0076
@@ -881,9 +897,19 @@
 #define USB_DEVICE_ID_MS_TOUCH_COVER_2   0x07a7
 #define USB_DEVICE_ID_MS_TYPE_COVER_2    0x07a9
 #define USB_DEVICE_ID_MS_POWER_COVER     0x07da
-#define USB_DEVICE_ID_MS_XBOX_ONE_S_CONTROLLER	0x02fd
+#define USB_DEVICE_ID_MS_SURFACE3_COVER		0x07de
+/*
+ * For a description of the Xbox controller models, refer to:
+ * https://en.wikipedia.org/wiki/Xbox_Wireless_Controller#Summary
+ */
+#define USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1708	0x02fd
+#define USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1708_BLE	0x0b20
+#define USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1914	0x0b13
+#define USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1797	0x0b05
+#define USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1797_BLE	0x0b22
 #define USB_DEVICE_ID_MS_PIXART_MOUSE    0x00cb
 #define USB_DEVICE_ID_8BITDO_SN30_PRO_PLUS      0x02e0
+#define USB_DEVICE_ID_MS_MOUSE_0783      0x0783
 
 #define USB_VENDOR_ID_MOJO		0x8282
 #define USB_DEVICE_ID_RETRO_ADAPTER	0x3201
@@ -956,7 +982,12 @@
 #define USB_DEVICE_ID_ORTEK_IHOME_IMAC_A210S	0x8003
 
 #define USB_VENDOR_ID_PLANTRONICS	0x047f
+#define USB_DEVICE_ID_PLANTRONICS_BLACKWIRE_3210_SERIES	0xc055
 #define USB_DEVICE_ID_PLANTRONICS_BLACKWIRE_3220_SERIES	0xc056
+#define USB_DEVICE_ID_PLANTRONICS_BLACKWIRE_3215_SERIES	0xc057
+#define USB_DEVICE_ID_PLANTRONICS_BLACKWIRE_3225_SERIES	0xc058
+#define USB_DEVICE_ID_PLANTRONICS_BLACKWIRE_3325_SERIES	0x430c
+#define USB_DEVICE_ID_PLANTRONICS_ENCOREPRO_500_SERIES		0x431e
 
 #define USB_VENDOR_ID_PANASONIC		0x04da
 #define USB_DEVICE_ID_PANABOARD_UBT780	0x1044
@@ -1006,6 +1037,7 @@
 #define USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH_3001		0x3001
 #define USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH_3003		0x3003
 #define USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH_3008		0x3008
+#define USB_DEVICE_ID_QUANTA_HP_5MP_CAMERA_5473		0x5473
 
 #define I2C_VENDOR_ID_RAYDIUM		0x2386
 #define I2C_PRODUCT_ID_RAYDIUM_4B33	0x4b33
@@ -1078,6 +1110,10 @@
 #define USB_VENDOR_ID_SIGMATEL		0x066F
 #define USB_DEVICE_ID_SIGMATEL_STMP3780	0x3780
 
+#define USB_VENDOR_ID_SINOWEALTH  0x258a
+#define USB_DEVICE_ID_GLORIOUS_MODEL_D 0x0033
+#define USB_DEVICE_ID_GLORIOUS_MODEL_O 0x0036
+
 #define USB_VENDOR_ID_SIS_TOUCH		0x0457
 #define USB_DEVICE_ID_SIS9200_TOUCH	0x9200
 #define USB_DEVICE_ID_SIS817_TOUCH	0x0817
@@ -1102,6 +1138,7 @@
 #define USB_DEVICE_ID_SONY_PS4_CONTROLLER_2	0x09cc
 #define USB_DEVICE_ID_SONY_PS4_CONTROLLER_DONGLE	0x0ba0
 #define USB_DEVICE_ID_SONY_PS5_CONTROLLER	0x0ce6
+#define USB_DEVICE_ID_SONY_PS5_CONTROLLER_2	0x0df2
 #define USB_DEVICE_ID_SONY_MOTION_CONTROLLER	0x03d5
 #define USB_DEVICE_ID_SONY_NAVIGATION_CONTROLLER	0x042f
 #define USB_DEVICE_ID_SONY_BUZZ_CONTROLLER		0x0002
@@ -1173,6 +1210,7 @@
 #define USB_DEVICE_ID_SYNAPTICS_DELL_K15A	0x6e21
 #define USB_DEVICE_ID_SYNAPTICS_ACER_ONE_S1002	0x73f4
 #define USB_DEVICE_ID_SYNAPTICS_ACER_ONE_S1003	0x73f5
+#define USB_DEVICE_ID_SYNAPTICS_ACER_SWITCH5_017	0x73f6
 #define USB_DEVICE_ID_SYNAPTICS_ACER_SWITCH5	0x81a7
 
 #define USB_VENDOR_ID_TEXAS_INSTRUMENTS	0x2047
@@ -1276,6 +1314,9 @@
 #define	USB_DEVICE_ID_WEIDA_8752	0xC300
 #define	USB_DEVICE_ID_WEIDA_8755	0xC301
 
+#define USB_VENDOR_ID_WINBOND		0x0416
+#define USB_DEVICE_ID_TSTP_MTOUCH	0xc168
+
 #define USB_VENDOR_ID_WISEGROUP		0x0925
 #define USB_DEVICE_ID_SMARTJOY_PLUS	0x0005
 #define USB_DEVICE_ID_SUPER_JOY_BOX_3	0x8888
@@ -1326,6 +1367,7 @@
 
 #define USB_VENDOR_ID_PRIMAX	0x0461
 #define USB_DEVICE_ID_PRIMAX_MOUSE_4D22	0x4d22
+#define USB_DEVICE_ID_PRIMAX_MOUSE_4E2A	0x4e2a
 #define USB_DEVICE_ID_PRIMAX_KEYBOARD	0x4e05
 #define USB_DEVICE_ID_PRIMAX_REZEL	0x4e72
 #define USB_DEVICE_ID_PRIMAX_PIXART_MOUSE_4D0F	0x4d0f
@@ -1346,6 +1388,7 @@
 #define USB_VENDOR_ID_UGTIZER			0x2179
 #define USB_DEVICE_ID_UGTIZER_TABLET_GP0610	0x0053
 #define USB_DEVICE_ID_UGTIZER_TABLET_GT5040	0x0077
+#define USB_DEVICE_ID_UGTIZER_TABLET_WP5540	0x0004
 
 #define USB_VENDOR_ID_VIEWSONIC			0x0543
 #define USB_DEVICE_ID_VIEWSONIC_PD1011		0xe621
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-input.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-input.c
@@ -160,6 +160,7 @@
 	if (usage) {
 		*old_keycode = usage->type == EV_KEY ?
 				usage->code : KEY_RESERVED;
+		usage->type = EV_KEY;
 		usage->code = ke->keycode;
 
 		clear_bit(*old_keycode, dev->keybit);
@@ -324,10 +325,18 @@
 	  HID_BATTERY_QUIRK_IGNORE },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELAN, USB_DEVICE_ID_ASUS_UX550_TOUCHSCREEN),
 	  HID_BATTERY_QUIRK_IGNORE },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ELAN, USB_DEVICE_ID_ASUS_UX550VE_TOUCHSCREEN),
+	  HID_BATTERY_QUIRK_IGNORE },
+	{ HID_I2C_DEVICE(USB_VENDOR_ID_ELAN, I2C_DEVICE_ID_HP_ENVY_X360_15T_DR100),
+	  HID_BATTERY_QUIRK_IGNORE },
 	{ HID_I2C_DEVICE(USB_VENDOR_ID_ELAN, I2C_DEVICE_ID_HP_SPECTRE_X360_15),
 	  HID_BATTERY_QUIRK_IGNORE },
 	{ HID_I2C_DEVICE(USB_VENDOR_ID_ELAN, I2C_DEVICE_ID_SURFACE_GO_TOUCHSCREEN),
 	  HID_BATTERY_QUIRK_IGNORE },
+	{ HID_I2C_DEVICE(USB_VENDOR_ID_ELAN, I2C_DEVICE_ID_SURFACE_GO2_TOUCHSCREEN),
+	  HID_BATTERY_QUIRK_IGNORE },
+	{ HID_I2C_DEVICE(USB_VENDOR_ID_ELAN, I2C_DEVICE_ID_LENOVO_YOGA_C630_TOUCHSCREEN),
+	  HID_BATTERY_QUIRK_IGNORE },
 	{}
 };
 
@@ -650,10 +659,9 @@
 						code += KEY_MACRO1;
 					else
 						code += BTN_TRIGGER_HAPPY - 0x1e;
-				} else {
-					goto ignore;
+					break;
 				}
-				break;
+				fallthrough;
 		default:
 			switch (field->physical) {
 			case HID_GD_MOUSE:
@@ -701,6 +709,14 @@
 			break;
 		}
 
+		if ((usage->hid & 0xf0) == 0xa0) {	/* SystemControl */
+			switch (usage->hid & 0xf) {
+			case 0x9: map_key_clear(KEY_MICMUTE); break;
+			default: goto ignore;
+			}
+			break;
+		}
+
 		if ((usage->hid & 0xf0) == 0xb0) {	/* SC - Display */
 			switch (usage->hid & 0xf) {
 			case 0x05: map_key_clear(KEY_SWITCHVIDEOMODE); break;
@@ -987,6 +1003,7 @@
 		case 0x0cd: map_key_clear(KEY_PLAYPAUSE);	break;
 		case 0x0cf: map_key_clear(KEY_VOICECOMMAND);	break;
 
+		case 0x0d8: map_key_clear(KEY_DICTATE);		break;
 		case 0x0d9: map_key_clear(KEY_EMOJI_PICKER);	break;
 
 		case 0x0e0: map_abs_clear(ABS_VOLUME);		break;
@@ -1078,6 +1095,8 @@
 
 		case 0x29d: map_key_clear(KEY_KBD_LAYOUT_NEXT);	break;
 
+		case 0x2a2: map_key_clear(KEY_ALL_APPLICATIONS);	break;
+
 		case 0x2c7: map_key_clear(KEY_KBDINPUTASSIST_PREV);		break;
 		case 0x2c8: map_key_clear(KEY_KBDINPUTASSIST_NEXT);		break;
 		case 0x2c9: map_key_clear(KEY_KBDINPUTASSIST_PREVGROUP);		break;
@@ -1328,6 +1347,12 @@
 
 	input = field->hidinput->input;
 
+	if (usage->type == EV_ABS &&
+	    (((*quirks & HID_QUIRK_X_INVERT) && usage->code == ABS_X) ||
+	     ((*quirks & HID_QUIRK_Y_INVERT) && usage->code == ABS_Y))) {
+		value = field->logical_maximum - value;
+	}
+
 	if (usage->hat_min < usage->hat_max || usage->hat_dir) {
 		int hat_dir = usage->hat_dir;
 		if (!hat_dir)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-ite.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-ite.c
@@ -121,6 +121,11 @@
 		     USB_VENDOR_ID_SYNAPTICS,
 		     USB_DEVICE_ID_SYNAPTICS_ACER_ONE_S1003),
 	  .driver_data = QUIRK_TOUCHPAD_ON_OFF_REPORT },
+	/* ITE8910 USB kbd ctlr, with Synaptics touchpad connected to it. */
+	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
+		     USB_VENDOR_ID_SYNAPTICS,
+		     USB_DEVICE_ID_SYNAPTICS_ACER_SWITCH5_017),
+	  .driver_data = QUIRK_TOUCHPAD_ON_OFF_REPORT },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, ite_devices);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-led.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-led.c
@@ -366,7 +366,7 @@
 		.type = DREAM_CHEEKY,
 		.name = "Dream Cheeky Webmail Notifier",
 		.short_name = "dream_cheeky",
-		.max_brightness = 31,
+		.max_brightness = 63,
 		.num_leds = 1,
 		.report_size = 9,
 		.report_type = RAW_REQUEST,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-lenovo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-lenovo.c
@@ -50,8 +50,13 @@
 	int select_right;
 	int sensitivity;
 	int press_speed;
-	u8 middlebutton_state; /* 0:Up, 1:Down (undecided), 2:Scrolling */
+	/* 0: Up
+	 * 1: Down (undecided)
+	 * 2: Scrolling
+	 */
+	u8 middlebutton_state;
 	bool fn_lock;
+	bool middleclick_workaround_cptkbd;
 };
 
 #define map_key_clear(c) hid_map_usage_clear(hi, usage, bit, max, EV_KEY, (c))
@@ -338,6 +343,7 @@
 		return lenovo_input_mapping_tp10_ultrabook_kbd(hdev, hi, field,
 							       usage, bit, max);
 	case USB_DEVICE_ID_LENOVO_X1_TAB:
+	case USB_DEVICE_ID_LENOVO_X1_TAB3:
 		return lenovo_input_mapping_x1_tab_kbd(hdev, hi, field, usage, bit, max);
 	default:
 		return 0;
@@ -426,6 +432,7 @@
 		break;
 	case USB_DEVICE_ID_LENOVO_TP10UBKBD:
 	case USB_DEVICE_ID_LENOVO_X1_TAB:
+	case USB_DEVICE_ID_LENOVO_X1_TAB3:
 		ret = lenovo_led_set_tp10ubkbd(hdev, TP10UBKBD_FN_LOCK_LED, value);
 		if (ret)
 			return ret;
@@ -464,6 +471,36 @@
 	return count;
 }
 
+static ssize_t attr_middleclick_workaround_show_cptkbd(struct device *dev,
+		struct device_attribute *attr,
+		char *buf)
+{
+	struct hid_device *hdev = to_hid_device(dev);
+	struct lenovo_drvdata *cptkbd_data = hid_get_drvdata(hdev);
+
+	return snprintf(buf, PAGE_SIZE, "%u\n",
+		cptkbd_data->middleclick_workaround_cptkbd);
+}
+
+static ssize_t attr_middleclick_workaround_store_cptkbd(struct device *dev,
+		struct device_attribute *attr,
+		const char *buf,
+		size_t count)
+{
+	struct hid_device *hdev = to_hid_device(dev);
+	struct lenovo_drvdata *cptkbd_data = hid_get_drvdata(hdev);
+	int value;
+
+	if (kstrtoint(buf, 10, &value))
+		return -EINVAL;
+	if (value < 0 || value > 1)
+		return -EINVAL;
+
+	cptkbd_data->middleclick_workaround_cptkbd = !!value;
+
+	return count;
+}
+
 
 static struct device_attribute dev_attr_fn_lock =
 	__ATTR(fn_lock, S_IWUSR | S_IRUGO,
@@ -475,10 +512,16 @@
 			attr_sensitivity_show_cptkbd,
 			attr_sensitivity_store_cptkbd);
 
+static struct device_attribute dev_attr_middleclick_workaround_cptkbd =
+	__ATTR(middleclick_workaround, S_IWUSR | S_IRUGO,
+			attr_middleclick_workaround_show_cptkbd,
+			attr_middleclick_workaround_store_cptkbd);
+
 
 static struct attribute *lenovo_attributes_cptkbd[] = {
 	&dev_attr_fn_lock.attr,
 	&dev_attr_sensitivity_cptkbd.attr,
+	&dev_attr_middleclick_workaround_cptkbd.attr,
 	NULL
 };
 
@@ -529,31 +572,33 @@
 {
 	struct lenovo_drvdata *cptkbd_data = hid_get_drvdata(hdev);
 
-	/* "wheel" scroll events */
-	if (usage->type == EV_REL && (usage->code == REL_WHEEL ||
-			usage->code == REL_HWHEEL)) {
-		/* Scroll events disable middle-click event */
-		cptkbd_data->middlebutton_state = 2;
-		return 0;
-	}
+	if (cptkbd_data->middleclick_workaround_cptkbd) {
+		/* "wheel" scroll events */
+		if (usage->type == EV_REL && (usage->code == REL_WHEEL ||
+				usage->code == REL_HWHEEL)) {
+			/* Scroll events disable middle-click event */
+			cptkbd_data->middlebutton_state = 2;
+			return 0;
+		}
 
-	/* Middle click events */
-	if (usage->type == EV_KEY && usage->code == BTN_MIDDLE) {
-		if (value == 1) {
-			cptkbd_data->middlebutton_state = 1;
-		} else if (value == 0) {
-			if (cptkbd_data->middlebutton_state == 1) {
-				/* No scrolling inbetween, send middle-click */
-				input_event(field->hidinput->input,
-					EV_KEY, BTN_MIDDLE, 1);
-				input_sync(field->hidinput->input);
-				input_event(field->hidinput->input,
-					EV_KEY, BTN_MIDDLE, 0);
-				input_sync(field->hidinput->input);
+		/* Middle click events */
+		if (usage->type == EV_KEY && usage->code == BTN_MIDDLE) {
+			if (value == 1) {
+				cptkbd_data->middlebutton_state = 1;
+			} else if (value == 0) {
+				if (cptkbd_data->middlebutton_state == 1) {
+					/* No scrolling inbetween, send middle-click */
+					input_event(field->hidinput->input,
+						EV_KEY, BTN_MIDDLE, 1);
+					input_sync(field->hidinput->input);
+					input_event(field->hidinput->input,
+						EV_KEY, BTN_MIDDLE, 0);
+					input_sync(field->hidinput->input);
+				}
+				cptkbd_data->middlebutton_state = 0;
 			}
-			cptkbd_data->middlebutton_state = 0;
+			return 1;
 		}
-		return 1;
 	}
 
 	return 0;
@@ -571,6 +616,7 @@
 		return lenovo_event_cptkbd(hdev, field, usage, value);
 	case USB_DEVICE_ID_LENOVO_TP10UBKBD:
 	case USB_DEVICE_ID_LENOVO_X1_TAB:
+	case USB_DEVICE_ID_LENOVO_X1_TAB3:
 		return lenovo_event_tp10ubkbd(hdev, field, usage, value);
 	default:
 		return 0;
@@ -853,6 +899,7 @@
 		break;
 	case USB_DEVICE_ID_LENOVO_TP10UBKBD:
 	case USB_DEVICE_ID_LENOVO_X1_TAB:
+	case USB_DEVICE_ID_LENOVO_X1_TAB3:
 		ret = lenovo_led_set_tp10ubkbd(hdev, tp10ubkbd_led[led_nr], value);
 		break;
 	}
@@ -992,6 +1039,7 @@
 	cptkbd_data->middlebutton_state = 0;
 	cptkbd_data->fn_lock = true;
 	cptkbd_data->sensitivity = 0x05;
+	cptkbd_data->middleclick_workaround_cptkbd = true;
 	lenovo_features_set_cptkbd(hdev);
 
 	ret = sysfs_create_group(&hdev->dev.kobj, &lenovo_attr_group_cptkbd);
@@ -1092,6 +1140,7 @@
 		break;
 	case USB_DEVICE_ID_LENOVO_TP10UBKBD:
 	case USB_DEVICE_ID_LENOVO_X1_TAB:
+	case USB_DEVICE_ID_LENOVO_X1_TAB3:
 		ret = lenovo_probe_tp10ubkbd(hdev);
 		break;
 	default:
@@ -1158,6 +1207,7 @@
 		break;
 	case USB_DEVICE_ID_LENOVO_TP10UBKBD:
 	case USB_DEVICE_ID_LENOVO_X1_TAB:
+	case USB_DEVICE_ID_LENOVO_X1_TAB3:
 		lenovo_remove_tp10ubkbd(hdev);
 		break;
 	}
@@ -1203,6 +1253,8 @@
 	 */
 	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
 		     USB_VENDOR_ID_LENOVO, USB_DEVICE_ID_LENOVO_X1_TAB) },
+	{ HID_DEVICE(BUS_USB, HID_GROUP_GENERIC,
+		     USB_VENDOR_ID_LENOVO, USB_DEVICE_ID_LENOVO_X1_TAB3) },
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-lg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-lg.c
@@ -749,12 +749,18 @@
 
 static int lg_probe(struct hid_device *hdev, const struct hid_device_id *id)
 {
-	struct usb_interface *iface = to_usb_interface(hdev->dev.parent);
-	__u8 iface_num = iface->cur_altsetting->desc.bInterfaceNumber;
+	struct usb_interface *iface;
+	__u8 iface_num;
 	unsigned int connect_mask = HID_CONNECT_DEFAULT;
 	struct lg_drv_data *drv_data;
 	int ret;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
+	iface = to_usb_interface(hdev->dev.parent);
+	iface_num = iface->cur_altsetting->desc.bInterfaceNumber;
+
 	/* G29 only work with the 1st interface */
 	if ((hdev->product == USB_DEVICE_ID_LOGITECH_G29_WHEEL) &&
 	    (iface_num != 0)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-lg4ff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-lg4ff.c
@@ -872,6 +872,12 @@
 		return -ENOMEM;
 
 	i = strlen(lbuf);
+
+	if (i == 0) {
+		kfree(lbuf);
+		return -EINVAL;
+	}
+
 	if (lbuf[i-1] == '\n') {
 		if (i == 1) {
 			kfree(lbuf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-logitech-dj.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-logitech-dj.c
@@ -965,9 +965,7 @@
 		}
 		break;
 	case REPORT_TYPE_MOUSE:
-		workitem->reports_supported |= STD_MOUSE | HIDPP;
-		if (djrcv_dev->type == recvr_type_mouse_only)
-			workitem->reports_supported |= MULTIMEDIA;
+		workitem->reports_supported |= STD_MOUSE | HIDPP | MULTIMEDIA;
 		break;
 	}
 }
@@ -1068,6 +1066,7 @@
 		workitem.reports_supported |= STD_KEYBOARD;
 		break;
 	case 0x0f:
+	case 0x11:
 		device_type = "eQUAD Lightspeed 1.2";
 		logi_hidpp_dev_conn_notif_equad(hdev, hidpp_report, &workitem);
 		workitem.reports_supported |= STD_KEYBOARD;
@@ -1284,6 +1283,11 @@
 		 * 50 msec should gives enough time to the receiver to be ready.
 		 */
 		msleep(50);
+
+		if (retval) {
+			kfree(dj_report);
+			return retval;
+		}
 	}
 
 	/*
@@ -1305,7 +1309,7 @@
 	buf[5] = 0x09;
 	buf[6] = 0x00;
 
-	hid_hw_raw_request(hdev, REPORT_ID_HIDPP_SHORT, buf,
+	retval = hid_hw_raw_request(hdev, REPORT_ID_HIDPP_SHORT, buf,
 			HIDPP_REPORT_SHORT_LENGTH, HID_OUTPUT_REPORT,
 			HID_REQ_SET_REPORT);
 
@@ -1777,7 +1781,7 @@
 	case recvr_type_bluetooth:	no_dj_interfaces = 2; break;
 	case recvr_type_dinovo:		no_dj_interfaces = 2; break;
 	}
-	if (hid_is_using_ll_driver(hdev, &usb_hid_driver)) {
+	if (hid_is_usb(hdev)) {
 		intf = to_usb_interface(hdev->dev.parent);
 		if (intf && intf->altsetting->desc.bInterfaceNumber >=
 							no_dj_interfaces) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-logitech-hidpp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-logitech-hidpp.c
@@ -31,11 +31,6 @@
 MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>");
 MODULE_AUTHOR("Nestor Lopez Casado <nlopezcasad@logitech.com>");
 
-static bool disable_raw_mode;
-module_param(disable_raw_mode, bool, 0644);
-MODULE_PARM_DESC(disable_raw_mode,
-	"Disable Raw mode reporting for touchpads and keep firmware gestures.");
-
 static bool disable_tap_to_click;
 module_param(disable_tap_to_click, bool, 0644);
 MODULE_PARM_DESC(disable_tap_to_click,
@@ -68,7 +63,7 @@
 /* bits 2..20 are reserved for classes */
 /* #define HIDPP_QUIRK_CONNECT_EVENTS		BIT(21) disabled */
 #define HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS	BIT(22)
-#define HIDPP_QUIRK_NO_HIDINPUT			BIT(23)
+#define HIDPP_QUIRK_DELAYED_INIT		BIT(23)
 #define HIDPP_QUIRK_FORCE_OUTPUT_REPORTS	BIT(24)
 #define HIDPP_QUIRK_UNIFYING			BIT(25)
 #define HIDPP_QUIRK_HI_RES_SCROLL_1P0		BIT(26)
@@ -87,8 +82,6 @@
 					 HIDPP_QUIRK_HI_RES_SCROLL_X2120 | \
 					 HIDPP_QUIRK_HI_RES_SCROLL_X2121)
 
-#define HIDPP_QUIRK_DELAYED_INIT		HIDPP_QUIRK_NO_HIDINPUT
-
 #define HIDPP_CAPABILITY_HIDPP10_BATTERY	BIT(0)
 #define HIDPP_CAPABILITY_HIDPP20_BATTERY	BIT(1)
 #define HIDPP_CAPABILITY_BATTERY_MILEAGE	BIT(2)
@@ -834,8 +827,7 @@
 	if (ret)
 		return ret;
 
-	snprintf(hdev->uniq, sizeof(hdev->uniq), "%04x-%4phD",
-		 hdev->product, &serial);
+	snprintf(hdev->uniq, sizeof(hdev->uniq), "%4phD", &serial);
 	dbg_hid("HID++ Unifying: Got serial: %s\n", hdev->uniq);
 
 	name = hidpp_unifying_get_name(hidpp);
@@ -929,6 +921,54 @@
 }
 
 /* -------------------------------------------------------------------------- */
+/* 0x0003: Device Information                                                 */
+/* -------------------------------------------------------------------------- */
+
+#define HIDPP_PAGE_DEVICE_INFORMATION			0x0003
+
+#define CMD_GET_DEVICE_INFO				0x00
+
+static int hidpp_get_serial(struct hidpp_device *hidpp, u32 *serial)
+{
+	struct hidpp_report response;
+	u8 feature_type;
+	u8 feature_index;
+	int ret;
+
+	ret = hidpp_root_get_feature(hidpp, HIDPP_PAGE_DEVICE_INFORMATION,
+				     &feature_index,
+				     &feature_type);
+	if (ret)
+		return ret;
+
+	ret = hidpp_send_fap_command_sync(hidpp, feature_index,
+					  CMD_GET_DEVICE_INFO,
+					  NULL, 0, &response);
+	if (ret)
+		return ret;
+
+	/* See hidpp_unifying_get_serial() */
+	*serial = *((u32 *)&response.rap.params[1]);
+	return 0;
+}
+
+static int hidpp_serial_init(struct hidpp_device *hidpp)
+{
+	struct hid_device *hdev = hidpp->hid_dev;
+	u32 serial;
+	int ret;
+
+	ret = hidpp_get_serial(hidpp, &serial);
+	if (ret)
+		return ret;
+
+	snprintf(hdev->uniq, sizeof(hdev->uniq), "%4phD", &serial);
+	dbg_hid("HID++ DeviceInformation: Got serial: %s\n", hdev->uniq);
+
+	return 0;
+}
+
+/* -------------------------------------------------------------------------- */
 /* 0x0005: GetDeviceNameType                                                  */
 /* -------------------------------------------------------------------------- */
 
@@ -1713,15 +1753,14 @@
 /* -------------------------------------------------------------------------- */
 #define HIDPP_PAGE_WIRELESS_DEVICE_STATUS			0x1d4b
 
-static int hidpp_set_wireless_feature_index(struct hidpp_device *hidpp)
+static int hidpp_get_wireless_feature_index(struct hidpp_device *hidpp, u8 *feature_index)
 {
 	u8 feature_type;
 	int ret;
 
 	ret = hidpp_root_get_feature(hidpp,
 				     HIDPP_PAGE_WIRELESS_DEVICE_STATUS,
-				     &hidpp->wireless_feature_index,
-				     &feature_type);
+				     feature_index, &feature_type);
 
 	return ret;
 }
@@ -3910,6 +3949,13 @@
 		}
 	}
 
+	if (hidpp->protocol_major >= 2) {
+		u8 feature_index;
+
+		if (!hidpp_get_wireless_feature_index(hidpp, &feature_index))
+			hidpp->wireless_feature_index = feature_index;
+	}
+
 	if (hidpp->name == hdev->name && hidpp->protocol_major >= 2) {
 		name = hidpp_get_device_name(hidpp);
 		if (name) {
@@ -3946,7 +3992,7 @@
 	if (hidpp->quirks & HIDPP_QUIRK_HI_RES_SCROLL)
 		hi_res_scroll_enable(hidpp);
 
-	if (!(hidpp->quirks & HIDPP_QUIRK_NO_HIDINPUT) || hidpp->delayed_input)
+	if (!(hidpp->quirks & HIDPP_QUIRK_DELAYED_INIT) || hidpp->delayed_input)
 		/* if the input nodes are already created, we can stop now */
 		return;
 
@@ -4089,11 +4135,6 @@
 	    hidpp_application_equals(hdev, HID_GD_KEYBOARD))
 		hidpp->quirks |= HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS;
 
-	if (disable_raw_mode) {
-		hidpp->quirks &= ~HIDPP_QUIRK_CLASS_WTP;
-		hidpp->quirks &= ~HIDPP_QUIRK_NO_HIDINPUT;
-	}
-
 	if (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP) {
 		ret = wtp_allocate(hdev, id);
 		if (ret)
@@ -4115,8 +4156,10 @@
 			 hdev->name);
 
 	/*
-	 * Plain USB connections need to actually call start and open
-	 * on the transport driver to allow incoming data.
+	 * First call hid_hw_start(hdev, 0) to allow IO without connecting any
+	 * hid subdrivers (hid-input, hidraw). This allows retrieving the dev's
+	 * name and serial number and store these in hdev->name and hdev->uniq,
+	 * before the hid-input and hidraw drivers expose these to userspace.
 	 */
 	ret = hid_hw_start(hdev, 0);
 	if (ret) {
@@ -4136,6 +4179,8 @@
 
 	if (hidpp->quirks & HIDPP_QUIRK_UNIFYING)
 		hidpp_unifying_init(hidpp);
+	else if (hid_is_usb(hidpp->hid_dev))
+		hidpp_serial_init(hidpp);
 
 	connected = hidpp_root_get_protocol_version(hidpp) == 0;
 	atomic_set(&hidpp->connected, connected);
@@ -4149,14 +4194,6 @@
 		hidpp_overwrite_name(hdev);
 	}
 
-	if (connected && hidpp->protocol_major >= 2) {
-		ret = hidpp_set_wireless_feature_index(hidpp);
-		if (ret == -ENOENT)
-			hidpp->wireless_feature_index = 0;
-		else if (ret)
-			goto hid_hw_init_fail;
-	}
-
 	if (connected && (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP)) {
 		ret = wtp_get_config(hidpp);
 		if (ret)
@@ -4167,21 +4204,17 @@
 			goto hid_hw_init_fail;
 	}
 
-	hidpp_connect_event(hidpp);
-
-	/* Reset the HID node state */
-	hid_device_io_stop(hdev);
-	hid_hw_close(hdev);
-	hid_hw_stop(hdev);
+	schedule_work(&hidpp->work);
+	flush_work(&hidpp->work);
 
-	if (hidpp->quirks & HIDPP_QUIRK_NO_HIDINPUT)
+	if (hidpp->quirks & HIDPP_QUIRK_DELAYED_INIT)
 		connect_mask &= ~HID_CONNECT_HIDINPUT;
 
 	/* Now export the actual inputs and hidraw nodes to the world */
-	ret = hid_hw_start(hdev, connect_mask);
+	ret = hid_connect(hdev, connect_mask);
 	if (ret) {
-		hid_err(hdev, "%s:hid_hw_start returned error\n", __func__);
-		goto hid_hw_start_fail;
+		hid_err(hdev, "%s:hid_connect returned error %d\n", __func__, ret);
+		goto hid_hw_init_fail;
 	}
 
 	if (hidpp->quirks & HIDPP_QUIRK_CLASS_G920) {
@@ -4192,6 +4225,11 @@
 				 ret);
 	}
 
+	/*
+	 * This relies on logi_dj_ll_close() being a no-op so that DJ connection
+	 * events will still be received.
+	 */
+	hid_hw_close(hdev);
 	return ret;
 
 hid_hw_init_fail:
@@ -4238,7 +4276,7 @@
 	{ /* wireless touchpad T651 */
 	  HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH,
 		USB_DEVICE_ID_LOGITECH_T651),
-	  .driver_data = HIDPP_QUIRK_CLASS_WTP },
+	  .driver_data = HIDPP_QUIRK_CLASS_WTP | HIDPP_QUIRK_DELAYED_INIT },
 	{ /* Mouse Logitech Anywhere MX */
 	  LDJ_DEVICE(0x1017), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_1P0 },
 	{ /* Mouse Logitech Cube */
@@ -4320,6 +4358,8 @@
 	  HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC086) },
 	{ /* Logitech G903 Hero Gaming Mouse over USB */
 	  HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC091) },
+	{ /* Logitech G915 TKL Keyboard over USB */
+	  HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC343) },
 	{ /* Logitech G920 Wheel over USB */
 	  HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_G920_WHEEL),
 		.driver_data = HIDPP_QUIRK_CLASS_G920 | HIDPP_QUIRK_FORCE_OUTPUT_REPORTS},
@@ -4335,6 +4375,8 @@
 	{ /* MX5500 keyboard over Bluetooth */
 	  HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH, 0xb30b),
 	  .driver_data = HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS },
+	{ /* Logitech G915 TKL keyboard over Bluetooth */
+	  HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH, 0xb35f) },
 	{ /* M-RCQ142 V470 Cordless Laser Mouse over Bluetooth */
 	  HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH, 0xb008) },
 	{ /* MX Master mouse over Bluetooth */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-magicmouse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-magicmouse.c
@@ -57,6 +57,8 @@
 #define MOUSE_REPORT_ID    0x29
 #define MOUSE2_REPORT_ID   0x12
 #define DOUBLE_REPORT_ID   0xf7
+#define USB_BATTERY_TIMEOUT_MS 60000
+
 /* These definitions are not precise, but they're close enough.  (Bits
  * 0x03 seem to indicate the aspect ratio of the touch, bits 0x70 seem
  * to be some kind of bit mask -- 0x20 may be a near-field reading,
@@ -140,6 +142,7 @@
 
 	struct hid_device *hdev;
 	struct delayed_work work;
+	struct timer_list battery_timer;
 };
 
 static int magicmouse_firm_touch(struct magicmouse_sc *msc)
@@ -256,8 +259,11 @@
 		unsigned long now = jiffies;
 		int step_x = msc->touches[id].scroll_x - x;
 		int step_y = msc->touches[id].scroll_y - y;
-		int step_hr = ((64 - (int)scroll_speed) * msc->scroll_accel) /
-			      SCROLL_HR_STEPS;
+		int step_hr =
+			max_t(int,
+			      ((64 - (int)scroll_speed) * msc->scroll_accel) /
+					SCROLL_HR_STEPS,
+			      1);
 		int step_x_hr = msc->touches[id].scroll_x_hr - x;
 		int step_y_hr = msc->touches[id].scroll_y_hr - y;
 
@@ -472,7 +478,7 @@
 		magicmouse_raw_event(hdev, report, data + 2, data[1]);
 		magicmouse_raw_event(hdev, report, data + 2 + data[1],
 			size - 2 - data[1]);
-		break;
+		return 0;
 	default:
 		return 0;
 	}
@@ -735,6 +741,44 @@
 		hid_err(msc->hdev, "unable to request touch data (%d)\n", ret);
 }
 
+static int magicmouse_fetch_battery(struct hid_device *hdev)
+{
+#ifdef CONFIG_HID_BATTERY_STRENGTH
+	struct hid_report_enum *report_enum;
+	struct hid_report *report;
+
+	if (!hdev->battery || hdev->vendor != USB_VENDOR_ID_APPLE ||
+	    (hdev->product != USB_DEVICE_ID_APPLE_MAGICMOUSE2 &&
+	     hdev->product != USB_DEVICE_ID_APPLE_MAGICTRACKPAD2))
+		return -1;
+
+	report_enum = &hdev->report_enum[hdev->battery_report_type];
+	report = report_enum->report_id_hash[hdev->battery_report_id];
+
+	if (!report || report->maxfield < 1)
+		return -1;
+
+	if (hdev->battery_capacity == hdev->battery_max)
+		return -1;
+
+	hid_hw_request(hdev, report, HID_REQ_GET_REPORT);
+	return 0;
+#else
+	return -1;
+#endif
+}
+
+static void magicmouse_battery_timer_tick(struct timer_list *t)
+{
+	struct magicmouse_sc *msc = from_timer(msc, t, battery_timer);
+	struct hid_device *hdev = msc->hdev;
+
+	if (magicmouse_fetch_battery(hdev) == 0) {
+		mod_timer(&msc->battery_timer,
+			  jiffies + msecs_to_jiffies(USB_BATTERY_TIMEOUT_MS));
+	}
+}
+
 static int magicmouse_probe(struct hid_device *hdev,
 	const struct hid_device_id *id)
 {
@@ -742,11 +786,6 @@
 	struct hid_report *report;
 	int ret;
 
-	if (id->vendor == USB_VENDOR_ID_APPLE &&
-	    id->product == USB_DEVICE_ID_APPLE_MAGICTRACKPAD2 &&
-	    hdev->type != HID_TYPE_USBMOUSE)
-		return -ENODEV;
-
 	msc = devm_kzalloc(&hdev->dev, sizeof(*msc), GFP_KERNEL);
 	if (msc == NULL) {
 		hid_err(hdev, "can't alloc magicmouse descriptor\n");
@@ -772,6 +811,16 @@
 		return ret;
 	}
 
+	timer_setup(&msc->battery_timer, magicmouse_battery_timer_tick, 0);
+	mod_timer(&msc->battery_timer,
+		  jiffies + msecs_to_jiffies(USB_BATTERY_TIMEOUT_MS));
+	magicmouse_fetch_battery(hdev);
+
+	if (id->vendor == USB_VENDOR_ID_APPLE &&
+	    (id->product == USB_DEVICE_ID_APPLE_MAGICMOUSE2 ||
+	     (id->product == USB_DEVICE_ID_APPLE_MAGICTRACKPAD2 && hdev->type != HID_TYPE_USBMOUSE)))
+		return 0;
+
 	if (!msc->input) {
 		hid_err(hdev, "magicmouse input not registered\n");
 		ret = -ENOMEM;
@@ -824,6 +873,7 @@
 
 	return 0;
 err_stop_hw:
+	del_timer_sync(&msc->battery_timer);
 	hid_hw_stop(hdev);
 	return ret;
 }
@@ -832,17 +882,52 @@
 {
 	struct magicmouse_sc *msc = hid_get_drvdata(hdev);
 
-	if (msc)
+	if (msc) {
 		cancel_delayed_work_sync(&msc->work);
+		del_timer_sync(&msc->battery_timer);
+	}
 
 	hid_hw_stop(hdev);
 }
 
+static __u8 *magicmouse_report_fixup(struct hid_device *hdev, __u8 *rdesc,
+				     unsigned int *rsize)
+{
+	/*
+	 * Change the usage from:
+	 *   0x06, 0x00, 0xff, // Usage Page (Vendor Defined Page 1)  0
+	 *   0x09, 0x0b,       // Usage (Vendor Usage 0x0b)           3
+	 * To:
+	 *   0x05, 0x01,       // Usage Page (Generic Desktop)        0
+	 *   0x09, 0x02,       // Usage (Mouse)                       2
+	 */
+	if (hdev->vendor == USB_VENDOR_ID_APPLE &&
+	    (hdev->product == USB_DEVICE_ID_APPLE_MAGICMOUSE2 ||
+	     hdev->product == USB_DEVICE_ID_APPLE_MAGICTRACKPAD2) &&
+	    *rsize == 83 && rdesc[46] == 0x84 && rdesc[58] == 0x85) {
+		hid_info(hdev,
+			 "fixing up magicmouse battery report descriptor\n");
+		*rsize = *rsize - 1;
+		rdesc = kmemdup(rdesc + 1, *rsize, GFP_KERNEL);
+		if (!rdesc)
+			return NULL;
+
+		rdesc[0] = 0x05;
+		rdesc[1] = 0x01;
+		rdesc[2] = 0x09;
+		rdesc[3] = 0x02;
+	}
+
+	return rdesc;
+}
+
 static const struct hid_device_id magic_mice[] = {
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_APPLE,
 		USB_DEVICE_ID_APPLE_MAGICMOUSE), .driver_data = 0 },
 	{ HID_BLUETOOTH_DEVICE(BT_VENDOR_ID_APPLE,
 		USB_DEVICE_ID_APPLE_MAGICMOUSE2), .driver_data = 0 },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE,
+		USB_DEVICE_ID_APPLE_MAGICMOUSE2), .driver_data = 0 },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_APPLE,
 		USB_DEVICE_ID_APPLE_MAGICTRACKPAD), .driver_data = 0 },
 	{ HID_BLUETOOTH_DEVICE(BT_VENDOR_ID_APPLE,
@@ -858,6 +943,7 @@
 	.id_table = magic_mice,
 	.probe = magicmouse_probe,
 	.remove = magicmouse_remove,
+	.report_fixup = magicmouse_report_fixup,
 	.raw_event = magicmouse_raw_event,
 	.event = magicmouse_event,
 	.input_mapping = magicmouse_input_mapping,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-mcp2221.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-mcp2221.c
@@ -385,6 +385,9 @@
 		data_len = 7;
 		break;
 	default:
+		if (len > I2C_SMBUS_BLOCK_MAX)
+			return -EINVAL;
+
 		memcpy(&mcp->txbuf[5], buf, len);
 		data_len = len + 5;
 	}
@@ -837,12 +840,19 @@
 		return ret;
 	}
 
-	ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW);
+	/*
+	 * This driver uses the .raw_event callback and therefore does not need any
+	 * HID_CONNECT_xxx flags.
+	 */
+	ret = hid_hw_start(hdev, 0);
 	if (ret) {
 		hid_err(hdev, "can't start hardware\n");
 		return ret;
 	}
 
+	hid_info(hdev, "USB HID v%x.%02x Device [%s] on %s\n", hdev->version >> 8,
+			hdev->version & 0xff, hdev->name, hdev->phys);
+
 	ret = hid_hw_open(hdev);
 	if (ret) {
 		hid_err(hdev, "can't open device\n");
@@ -867,8 +877,7 @@
 	mcp->adapter.retries = 1;
 	mcp->adapter.dev.parent = &hdev->dev;
 	snprintf(mcp->adapter.name, sizeof(mcp->adapter.name),
-			"MCP2221 usb-i2c bridge on hidraw%d",
-			((struct hidraw *)hdev->hidraw)->minor);
+			"MCP2221 usb-i2c bridge");
 
 	ret = i2c_add_adapter(&mcp->adapter);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-microsoft.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-microsoft.c
@@ -446,7 +446,16 @@
 		.driver_data = MS_PRESENTER },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, 0x091B),
 		.driver_data = MS_SURFACE_DIAL },
-	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_ONE_S_CONTROLLER),
+
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1708),
+		.driver_data = MS_QUIRK_FF },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1708_BLE),
+		.driver_data = MS_QUIRK_FF },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1914),
+		.driver_data = MS_QUIRK_FF },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1797),
+		.driver_data = MS_QUIRK_FF },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_CONTROLLER_MODEL_1797_BLE),
 		.driver_data = MS_QUIRK_FF },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_8BITDO_SN30_PRO_PLUS),
 		.driver_data = MS_QUIRK_FF },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-multitouch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-multitouch.c
@@ -71,6 +71,7 @@
 #define MT_QUIRK_SEPARATE_APP_REPORT	BIT(19)
 #define MT_QUIRK_FORCE_MULTI_INPUT	BIT(20)
 #define MT_QUIRK_DISABLE_WAKEUP		BIT(21)
+#define MT_QUIRK_ORIENTATION_INVERT	BIT(22)
 
 #define MT_INPUTMODE_TOUCHSCREEN	0x02
 #define MT_INPUTMODE_TOUCHPAD		0x03
@@ -193,6 +194,8 @@
 /* reserved					0x0014 */
 #define MT_CLS_WIN_8_FORCE_MULTI_INPUT		0x0015
 #define MT_CLS_WIN_8_DISABLE_WAKEUP		0x0016
+#define MT_CLS_WIN_8_NO_STICKY_FINGERS		0x0017
+#define MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU	0x0018
 
 /* vendor specific classes */
 #define MT_CLS_3M				0x0101
@@ -285,6 +288,15 @@
 			MT_QUIRK_WIN8_PTP_BUTTONS |
 			MT_QUIRK_FORCE_MULTI_INPUT,
 		.export_all_inputs = true },
+	{ .name = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+		.quirks = MT_QUIRK_IGNORE_DUPLICATES |
+			MT_QUIRK_HOVERING |
+			MT_QUIRK_CONTACT_CNT_ACCURATE |
+			MT_QUIRK_STICKY_FINGERS |
+			MT_QUIRK_WIN8_PTP_BUTTONS |
+			MT_QUIRK_FORCE_MULTI_INPUT |
+			MT_QUIRK_NOT_SEEN_MEANS_UP,
+		.export_all_inputs = true },
 	{ .name = MT_CLS_WIN_8_DISABLE_WAKEUP,
 		.quirks = MT_QUIRK_ALWAYS_VALID |
 			MT_QUIRK_IGNORE_DUPLICATES |
@@ -294,6 +306,13 @@
 			MT_QUIRK_WIN8_PTP_BUTTONS |
 			MT_QUIRK_DISABLE_WAKEUP,
 		.export_all_inputs = true },
+	{ .name = MT_CLS_WIN_8_NO_STICKY_FINGERS,
+		.quirks = MT_QUIRK_ALWAYS_VALID |
+			MT_QUIRK_IGNORE_DUPLICATES |
+			MT_QUIRK_HOVERING |
+			MT_QUIRK_CONTACT_CNT_ACCURATE |
+			MT_QUIRK_WIN8_PTP_BUTTONS,
+		.export_all_inputs = true },
 
 	/*
 	 * vendor specific classes
@@ -775,6 +794,7 @@
 		case HID_DG_CONFIDENCE:
 			if ((cls->name == MT_CLS_WIN_8 ||
 			     cls->name == MT_CLS_WIN_8_FORCE_MULTI_INPUT ||
+			     cls->name == MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU ||
 			     cls->name == MT_CLS_WIN_8_DISABLE_WAKEUP) &&
 				(field->application == HID_DG_TOUCHPAD ||
 				 field->application == HID_DG_TOUCHSCREEN))
@@ -990,6 +1010,7 @@
 			    struct mt_usages *slot)
 {
 	struct input_mt *mt = input->mt;
+	struct hid_device *hdev = td->hdev;
 	__s32 quirks = app->quirks;
 	bool valid = true;
 	bool confidence_state = true;
@@ -1067,6 +1088,10 @@
 		int orientation = wide;
 		int max_azimuth;
 		int azimuth;
+		int x;
+		int y;
+		int cx;
+		int cy;
 
 		if (slot->a != DEFAULT_ZERO) {
 			/*
@@ -1085,6 +1110,9 @@
 			if (azimuth > max_azimuth * 2)
 				azimuth -= max_azimuth * 4;
 			orientation = -azimuth;
+			if (quirks & MT_QUIRK_ORIENTATION_INVERT)
+				orientation = -orientation;
+
 		}
 
 		if (quirks & MT_QUIRK_TOUCH_SIZE_SCALING) {
@@ -1096,10 +1124,23 @@
 			minor = minor >> 1;
 		}
 
-		input_event(input, EV_ABS, ABS_MT_POSITION_X, *slot->x);
-		input_event(input, EV_ABS, ABS_MT_POSITION_Y, *slot->y);
-		input_event(input, EV_ABS, ABS_MT_TOOL_X, *slot->cx);
-		input_event(input, EV_ABS, ABS_MT_TOOL_Y, *slot->cy);
+		x = hdev->quirks & HID_QUIRK_X_INVERT ?
+			input_abs_get_max(input, ABS_MT_POSITION_X) - *slot->x :
+			*slot->x;
+		y = hdev->quirks & HID_QUIRK_Y_INVERT ?
+			input_abs_get_max(input, ABS_MT_POSITION_Y) - *slot->y :
+			*slot->y;
+		cx = hdev->quirks & HID_QUIRK_X_INVERT ?
+			input_abs_get_max(input, ABS_MT_POSITION_X) - *slot->cx :
+			*slot->cx;
+		cy = hdev->quirks & HID_QUIRK_Y_INVERT ?
+			input_abs_get_max(input, ABS_MT_POSITION_Y) - *slot->cy :
+			*slot->cy;
+
+		input_event(input, EV_ABS, ABS_MT_POSITION_X, x);
+		input_event(input, EV_ABS, ABS_MT_POSITION_Y, y);
+		input_event(input, EV_ABS, ABS_MT_TOOL_X, cx);
+		input_event(input, EV_ABS, ABS_MT_TOOL_Y, cy);
 		input_event(input, EV_ABS, ABS_MT_DISTANCE, !*slot->tip_state);
 		input_event(input, EV_ABS, ABS_MT_ORIENTATION, orientation);
 		input_event(input, EV_ABS, ABS_MT_PRESSURE, *slot->p);
@@ -1167,7 +1208,7 @@
 	int contact_count = -1;
 
 	/* sticky fingers release in progress, abort */
-	if (test_and_set_bit(MT_IO_FLAGS_RUNNING, &td->mt_io_flags))
+	if (test_and_set_bit_lock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags))
 		return;
 
 	scantime = *app->scantime;
@@ -1248,7 +1289,7 @@
 			del_timer(&td->release_timer);
 	}
 
-	clear_bit(MT_IO_FLAGS_RUNNING, &td->mt_io_flags);
+	clear_bit_unlock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags);
 }
 
 static int mt_touch_input_configured(struct hid_device *hdev,
@@ -1401,6 +1442,30 @@
 	return 0;
 }
 
+static __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
+			     unsigned int *size)
+{
+	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
+	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
+	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
+		if (rdesc[607] == 0x15) {
+			rdesc[607] = 0x25;
+			dev_info(
+				&hdev->dev,
+				"GT7868Q report descriptor fixup is applied.\n");
+		} else {
+			dev_info(
+				&hdev->dev,
+				"The byte is not expected for fixing the report descriptor. \
+It's possible that the touchpad firmware is not suitable for applying the fix. \
+got: %x\n",
+				rdesc[607]);
+		}
+	}
+
+	return rdesc;
+}
+
 static void mt_report(struct hid_device *hid, struct hid_report *report)
 {
 	struct mt_device *td = hid_get_drvdata(hid);
@@ -1553,7 +1618,6 @@
 static int mt_input_configured(struct hid_device *hdev, struct hid_input *hi)
 {
 	struct mt_device *td = hid_get_drvdata(hdev);
-	char *name;
 	const char *suffix = NULL;
 	struct mt_report_data *rdata;
 	struct mt_application *mt_application = NULL;
@@ -1608,13 +1672,10 @@
 	}
 
 	if (suffix) {
-		name = devm_kzalloc(&hi->input->dev,
-				    strlen(hdev->name) + strlen(suffix) + 2,
-				    GFP_KERNEL);
-		if (name) {
-			sprintf(name, "%s %s", hdev->name, suffix);
-			hi->input->name = name;
-		}
+		hi->input->name = devm_kasprintf(&hdev->dev, GFP_KERNEL,
+						 "%s %s", hdev->name, suffix);
+		if (!hi->input->name)
+			return -ENOMEM;
 	}
 
 	return 0;
@@ -1683,11 +1744,11 @@
 	 * An input report came in just before we release the sticky fingers,
 	 * it will take care of the sticky fingers.
 	 */
-	if (test_and_set_bit(MT_IO_FLAGS_RUNNING, &td->mt_io_flags))
+	if (test_and_set_bit_lock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags))
 		return;
 	if (test_bit(MT_IO_FLAGS_PENDING_SLOTS, &td->mt_io_flags))
 		mt_release_contacts(hdev);
-	clear_bit(MT_IO_FLAGS_RUNNING, &td->mt_io_flags);
+	clear_bit_unlock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags);
 }
 
 static int mt_probe(struct hid_device *hdev, const struct hid_device_id *id)
@@ -1719,6 +1780,15 @@
 	if (id->vendor == HID_ANY_ID && id->product == HID_ANY_ID)
 		td->serial_maybe = true;
 
+
+	/* Orientation is inverted if the X or Y axes are
+	 * flipped, but normalized if both are inverted.
+	 */
+	if (hdev->quirks & (HID_QUIRK_X_INVERT | HID_QUIRK_Y_INVERT) &&
+	    !((hdev->quirks & HID_QUIRK_X_INVERT)
+	      && (hdev->quirks & HID_QUIRK_Y_INVERT)))
+		td->mtclass.quirks = MT_QUIRK_ORIENTATION_INVERT;
+
 	/* This allows the driver to correctly support devices
 	 * that emit events over several HID messages.
 	 */
@@ -1946,6 +2016,14 @@
 		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
 			USB_VENDOR_ID_ELAN, 0x313a) },
 
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT,
+		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
+			USB_VENDOR_ID_ELAN, 0x3148) },
+
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
+			USB_VENDOR_ID_ELAN, 0x32ae) },
+
 	/* Elitegroup panel */
 	{ .driver_data = MT_CLS_SERIAL,
 		MT_USB_DEVICE(USB_VENDOR_ID_ELITEGROUP,
@@ -1989,6 +2067,14 @@
 		MT_BT_DEVICE(USB_VENDOR_ID_FRUCTEL,
 			USB_DEVICE_ID_GAMETEL_MT_MODE) },
 
+	/* Goodix GT7868Q devices */
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+	  HID_DEVICE(BUS_I2C, HID_GROUP_ANY, I2C_VENDOR_ID_GOODIX,
+		     I2C_DEVICE_ID_GOODIX_01E8) },
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+	  HID_DEVICE(BUS_I2C, HID_GROUP_ANY, I2C_VENDOR_ID_GOODIX,
+		     I2C_DEVICE_ID_GOODIX_01E9) },
+
 	/* GoodTouch panels */
 	{ .driver_data = MT_CLS_NSMU,
 		MT_USB_DEVICE(USB_VENDOR_ID_GOODTOUCH,
@@ -1999,6 +2085,16 @@
 		MT_USB_DEVICE(USB_VENDOR_ID_HANVON_ALT,
 			USB_DEVICE_ID_HANVON_ALT_MULTITOUCH) },
 
+	/* HONOR GLO-GXXX panel */
+	{ .driver_data = MT_CLS_VTL,
+		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
+			0x347d, 0x7853) },
+
+	/* HONOR MagicBook Art 14 touchpad */
+	{ .driver_data = MT_CLS_VTL,
+		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
+			0x35cc, 0x0104) },
+
 	/* Ilitek dual touch panel */
 	{  .driver_data = MT_CLS_NSMU,
 		MT_USB_DEVICE(USB_VENDOR_ID_ILITEK,
@@ -2024,6 +2120,28 @@
 			   USB_VENDOR_ID_LENOVO,
 			   USB_DEVICE_ID_LENOVO_X1_TAB3) },
 
+	/* Lenovo X12 TAB Gen 1 */
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+		HID_DEVICE(BUS_USB, HID_GROUP_MULTITOUCH_WIN_8,
+			   USB_VENDOR_ID_LENOVO,
+			   USB_DEVICE_ID_LENOVO_X12_TAB) },
+
+	/* Lenovo X12 TAB Gen 2 */
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+		HID_DEVICE(BUS_USB, HID_GROUP_MULTITOUCH_WIN_8,
+			   USB_VENDOR_ID_LENOVO,
+			   USB_DEVICE_ID_LENOVO_X12_TAB2) },
+
+	/* Logitech devices */
+	{ .driver_data = MT_CLS_NSMU,
+		HID_DEVICE(BUS_BLUETOOTH, HID_GROUP_MULTITOUCH_WIN_8,
+			USB_VENDOR_ID_LOGITECH,
+			USB_DEVICE_ID_LOGITECH_CASA_TOUCHPAD) },
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT_NSMU,
+		HID_DEVICE(BUS_USB, HID_GROUP_MULTITOUCH_WIN_8,
+			USB_VENDOR_ID_LOGITECH,
+			USB_DEVICE_ID_LOGITECH_BOLT_RECEIVER) },
+
 	/* MosArt panels */
 	{ .driver_data = MT_CLS_CONFIDENCE_MINUS_ONE,
 		MT_USB_DEVICE(USB_VENDOR_ID_ASUS,
@@ -2091,6 +2209,14 @@
 	/* Synaptics devices */
 	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT,
 		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
+			USB_VENDOR_ID_SYNAPTICS, 0xcd7e) },
+
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT,
+		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
+			USB_VENDOR_ID_SYNAPTICS, 0xcddc) },
+
+	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT,
+		HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8,
 			USB_VENDOR_ID_SYNAPTICS, 0xce08) },
 
 	{ .driver_data = MT_CLS_WIN_8_FORCE_MULTI_INPUT,
@@ -2120,6 +2246,11 @@
 		MT_USB_DEVICE(USB_VENDOR_ID_VTL,
 			USB_DEVICE_ID_VTL_MULTITOUCH_FF3F) },
 
+	/* Winbond Electronics Corp. */
+	{ .driver_data = MT_CLS_WIN_8_NO_STICKY_FINGERS,
+		HID_DEVICE(HID_BUS_ANY, HID_GROUP_MULTITOUCH_WIN_8,
+			   USB_VENDOR_ID_WINBOND, USB_DEVICE_ID_TSTP_MTOUCH) },
+
 	/* Wistron panels */
 	{ .driver_data = MT_CLS_NSMU,
 		MT_USB_DEVICE(USB_VENDOR_ID_WISTRON,
@@ -2163,6 +2294,9 @@
 	{ .driver_data = MT_CLS_GOOGLE,
 		HID_DEVICE(HID_BUS_ANY, HID_GROUP_ANY, USB_VENDOR_ID_GOOGLE,
 			USB_DEVICE_ID_GOOGLE_TOUCH_ROSE) },
+	{ .driver_data = MT_CLS_GOOGLE,
+		HID_DEVICE(BUS_USB, HID_GROUP_MULTITOUCH_WIN_8, USB_VENDOR_ID_GOOGLE,
+			USB_DEVICE_ID_GOOGLE_WHISKERS) },
 
 	/* Generic MT device */
 	{ HID_DEVICE(HID_BUS_ANY, HID_GROUP_MULTITOUCH, HID_ANY_ID, HID_ANY_ID) },
@@ -2191,6 +2325,7 @@
 	.feature_mapping = mt_feature_mapping,
 	.usage_table = mt_grabbed_usages,
 	.event = mt_event,
+	.report_fixup = mt_report_fixup,
 	.report = mt_report,
 #ifdef CONFIG_PM
 	.suspend = mt_suspend,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-picolcd_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-picolcd_fb.c
@@ -432,7 +432,7 @@
 
 
 /* Callback from deferred IO workqueue */
-static void picolcd_fb_deferred_io(struct fb_info *info, struct list_head *pagelist)
+static void picolcd_fb_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	picolcd_fb_update(info);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-plantronics.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-plantronics.c
@@ -6,9 +6,6 @@
  *  Copyright (c) 2015-2018 Terry Junge <terry.junge@plantronics.com>
  */
 
-/*
- */
-
 #include "hid-ids.h"
 
 #include <linux/hid.h>
@@ -23,28 +20,28 @@
 
 #define PLT_VOL_UP		0x00b1
 #define PLT_VOL_DOWN		0x00b2
+#define PLT_MIC_MUTE		0x00b5
 
 #define PLT1_VOL_UP		(PLT_HID_1_0_PAGE | PLT_VOL_UP)
 #define PLT1_VOL_DOWN		(PLT_HID_1_0_PAGE | PLT_VOL_DOWN)
+#define PLT1_MIC_MUTE		(PLT_HID_1_0_PAGE | PLT_MIC_MUTE)
 #define PLT2_VOL_UP		(PLT_HID_2_0_PAGE | PLT_VOL_UP)
 #define PLT2_VOL_DOWN		(PLT_HID_2_0_PAGE | PLT_VOL_DOWN)
+#define PLT2_MIC_MUTE		(PLT_HID_2_0_PAGE | PLT_MIC_MUTE)
+#define HID_TELEPHONY_MUTE	(HID_UP_TELEPHONY | 0x2f)
+#define HID_CONSUMER_MUTE	(HID_UP_CONSUMER | 0xe2)
 
 #define PLT_DA60		0xda60
 #define PLT_BT300_MIN		0x0413
 #define PLT_BT300_MAX		0x0418
 
-
-#define PLT_ALLOW_CONSUMER (field->application == HID_CP_CONSUMERCONTROL && \
-			    (usage->hid & HID_USAGE_PAGE) == HID_UP_CONSUMER)
-
-#define PLT_QUIRK_DOUBLE_VOLUME_KEYS BIT(0)
-
 #define PLT_DOUBLE_KEY_TIMEOUT 5 /* ms */
 
 struct plt_drv_data {
 	unsigned long device_type;
-	unsigned long last_volume_key_ts;
-	u32 quirks;
+	unsigned long last_key_ts;
+	unsigned long double_key_to;
+	__u16 last_key;
 };
 
 static int plantronics_input_mapping(struct hid_device *hdev,
@@ -56,34 +53,43 @@
 	unsigned short mapped_key;
 	struct plt_drv_data *drv_data = hid_get_drvdata(hdev);
 	unsigned long plt_type = drv_data->device_type;
+	int allow_mute = usage->hid == HID_TELEPHONY_MUTE;
+	int allow_consumer = field->application == HID_CP_CONSUMERCONTROL &&
+			(usage->hid & HID_USAGE_PAGE) == HID_UP_CONSUMER &&
+			usage->hid != HID_CONSUMER_MUTE;
 
 	/* special case for PTT products */
 	if (field->application == HID_GD_JOYSTICK)
 		goto defaulted;
 
-	/* handle volume up/down mapping */
 	/* non-standard types or multi-HID interfaces - plt_type is PID */
 	if (!(plt_type & HID_USAGE_PAGE)) {
 		switch (plt_type) {
 		case PLT_DA60:
-			if (PLT_ALLOW_CONSUMER)
+			if (allow_consumer)
 				goto defaulted;
-			goto ignored;
+			if (usage->hid == HID_CONSUMER_MUTE) {
+				mapped_key = KEY_MICMUTE;
+				goto mapped;
+			}
+			break;
 		default:
-			if (PLT_ALLOW_CONSUMER)
+			if (allow_consumer || allow_mute)
 				goto defaulted;
 		}
+		goto ignored;
 	}
-	/* handle standard types - plt_type is 0xffa0uuuu or 0xffa2uuuu */
-	/* 'basic telephony compliant' - allow default consumer page map */
-	else if ((plt_type & HID_USAGE) >= PLT_BASIC_TELEPHONY &&
-		 (plt_type & HID_USAGE) != PLT_BASIC_EXCEPTION) {
-		if (PLT_ALLOW_CONSUMER)
-			goto defaulted;
-	}
-	/* not 'basic telephony' - apply legacy mapping */
-	/* only map if the field is in the device's primary vendor page */
-	else if (!((field->application ^ plt_type) & HID_USAGE_PAGE)) {
+
+	/* handle standard consumer control mapping */
+	/* and standard telephony mic mute mapping */
+	if (allow_consumer || allow_mute)
+		goto defaulted;
+
+	/* handle vendor unique types - plt_type is 0xffa0uuuu or 0xffa2uuuu */
+	/* if not 'basic telephony compliant' - map vendor unique controls */
+	if (!((plt_type & HID_USAGE) >= PLT_BASIC_TELEPHONY &&
+	      (plt_type & HID_USAGE) != PLT_BASIC_EXCEPTION) &&
+	      !((field->application ^ plt_type) & HID_USAGE_PAGE))
 		switch (usage->hid) {
 		case PLT1_VOL_UP:
 		case PLT2_VOL_UP:
@@ -93,8 +99,11 @@
 		case PLT2_VOL_DOWN:
 			mapped_key = KEY_VOLUMEDOWN;
 			goto mapped;
+		case PLT1_MIC_MUTE:
+		case PLT2_MIC_MUTE:
+			mapped_key = KEY_MICMUTE;
+			goto mapped;
 		}
-	}
 
 /*
  * Future mapping of call control or other usages,
@@ -103,6 +112,8 @@
  */
 
 ignored:
+	hid_dbg(hdev, "usage: %08x (appl: %08x) - ignored\n",
+		usage->hid, field->application);
 	return -1;
 
 defaulted:
@@ -121,23 +132,26 @@
 			     struct hid_usage *usage, __s32 value)
 {
 	struct plt_drv_data *drv_data = hid_get_drvdata(hdev);
+	unsigned long prev_tsto, cur_ts;
+	__u16 prev_key, cur_key;
 
-	if (drv_data->quirks & PLT_QUIRK_DOUBLE_VOLUME_KEYS) {
-		unsigned long prev_ts, cur_ts;
-
-		/* Usages are filtered in plantronics_usages. */
+	/* Usages are filtered in plantronics_usages. */
 
-		if (!value) /* Handle key presses only. */
-			return 0;
-
-		prev_ts = drv_data->last_volume_key_ts;
-		cur_ts = jiffies;
-		if (jiffies_to_msecs(cur_ts - prev_ts) <= PLT_DOUBLE_KEY_TIMEOUT)
-			return 1; /* Ignore the repeated key. */
-
-		drv_data->last_volume_key_ts = cur_ts;
+	/* HZ too low for ms resolution - double key detection disabled */
+	/* or it is a key release - handle key presses only. */
+	if (!drv_data->double_key_to || !value)
+		return 0;
+
+	prev_tsto = drv_data->last_key_ts + drv_data->double_key_to;
+	cur_ts = drv_data->last_key_ts = jiffies;
+	prev_key = drv_data->last_key;
+	cur_key = drv_data->last_key = usage->code;
+
+	/* If the same key occurs in <= double_key_to -- ignore it */
+	if (prev_key == cur_key && time_before_eq(cur_ts, prev_tsto)) {
+		hid_dbg(hdev, "double key %d ignored\n", cur_key);
+		return 1; /* Ignore the repeated key. */
 	}
-
 	return 0;
 }
 
@@ -179,12 +193,16 @@
 	ret = hid_parse(hdev);
 	if (ret) {
 		hid_err(hdev, "parse failed\n");
-		goto err;
+		return ret;
 	}
 
 	drv_data->device_type = plantronics_device_type(hdev);
-	drv_data->quirks = id->driver_data;
-	drv_data->last_volume_key_ts = jiffies - msecs_to_jiffies(PLT_DOUBLE_KEY_TIMEOUT);
+	drv_data->double_key_to = msecs_to_jiffies(PLT_DOUBLE_KEY_TIMEOUT);
+	drv_data->last_key_ts = jiffies - drv_data->double_key_to;
+
+	/* if HZ does not allow ms resolution - disable double key detection */
+	if (drv_data->double_key_to < PLT_DOUBLE_KEY_TIMEOUT)
+		drv_data->double_key_to = 0;
 
 	hid_set_drvdata(hdev, drv_data);
 
@@ -193,14 +211,10 @@
 	if (ret)
 		hid_err(hdev, "hw start failed\n");
 
-err:
 	return ret;
 }
 
 static const struct hid_device_id plantronics_devices[] = {
-	{ HID_USB_DEVICE(USB_VENDOR_ID_PLANTRONICS,
-					 USB_DEVICE_ID_PLANTRONICS_BLACKWIRE_3220_SERIES),
-		.driver_data = PLT_QUIRK_DOUBLE_VOLUME_KEYS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PLANTRONICS, HID_ANY_ID) },
 	{ }
 };
@@ -209,6 +223,14 @@
 static const struct hid_usage_id plantronics_usages[] = {
 	{ HID_CP_VOLUMEUP, EV_KEY, HID_ANY_ID },
 	{ HID_CP_VOLUMEDOWN, EV_KEY, HID_ANY_ID },
+	{ HID_TELEPHONY_MUTE, EV_KEY, HID_ANY_ID },
+	{ HID_CONSUMER_MUTE, EV_KEY, HID_ANY_ID },
+	{ PLT2_VOL_UP, EV_KEY, HID_ANY_ID },
+	{ PLT2_VOL_DOWN, EV_KEY, HID_ANY_ID },
+	{ PLT2_MIC_MUTE, EV_KEY, HID_ANY_ID },
+	{ PLT1_VOL_UP, EV_KEY, HID_ANY_ID },
+	{ PLT1_VOL_DOWN, EV_KEY, HID_ANY_ID },
+	{ PLT1_MIC_MUTE, EV_KEY, HID_ANY_ID },
 	{ HID_TERMINATOR, HID_TERMINATOR, HID_TERMINATOR }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-playstation.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-playstation.c
@@ -626,6 +626,7 @@
 
 static int dualsense_get_calibration_data(struct dualsense *ds)
 {
+	struct hid_device *hdev = ds->base.hdev;
 	short gyro_pitch_bias, gyro_pitch_plus, gyro_pitch_minus;
 	short gyro_yaw_bias, gyro_yaw_plus, gyro_yaw_minus;
 	short gyro_roll_bias, gyro_roll_plus, gyro_roll_minus;
@@ -636,6 +637,7 @@
 	int speed_2x;
 	int range_2g;
 	int ret = 0;
+	int i;
 	uint8_t *buf;
 
 	buf = kzalloc(DS_FEATURE_REPORT_CALIBRATION_SIZE, GFP_KERNEL);
@@ -688,6 +690,21 @@
 	ds->gyro_calib_data[2].sens_denom = gyro_roll_plus - gyro_roll_minus;
 
 	/*
+	 * Sanity check gyro calibration data. This is needed to prevent crashes
+	 * during report handling of virtual, clone or broken devices not implementing
+	 * calibration data properly.
+	 */
+	for (i = 0; i < ARRAY_SIZE(ds->gyro_calib_data); i++) {
+		if (ds->gyro_calib_data[i].sens_denom == 0) {
+			hid_warn(hdev, "Invalid gyro calibration data for axis (%d), disabling calibration.",
+					ds->gyro_calib_data[i].abs_code);
+			ds->gyro_calib_data[i].bias = 0;
+			ds->gyro_calib_data[i].sens_numer = DS_GYRO_RANGE;
+			ds->gyro_calib_data[i].sens_denom = S16_MAX;
+		}
+	}
+
+	/*
 	 * Set accelerometer calibration and normalization parameters.
 	 * Data values will be normalized to 1/DS_ACC_RES_PER_G g.
 	 */
@@ -709,6 +726,21 @@
 	ds->accel_calib_data[2].sens_numer = 2*DS_ACC_RES_PER_G;
 	ds->accel_calib_data[2].sens_denom = range_2g;
 
+	/*
+	 * Sanity check accelerometer calibration data. This is needed to prevent crashes
+	 * during report handling of virtual, clone or broken devices not implementing calibration
+	 * data properly.
+	 */
+	for (i = 0; i < ARRAY_SIZE(ds->accel_calib_data); i++) {
+		if (ds->accel_calib_data[i].sens_denom == 0) {
+			hid_warn(hdev, "Invalid accelerometer calibration data for axis (%d), disabling calibration.",
+					ds->accel_calib_data[i].abs_code);
+			ds->accel_calib_data[i].bias = 0;
+			ds->accel_calib_data[i].sens_numer = DS_ACC_RANGE;
+			ds->accel_calib_data[i].sens_denom = S16_MAX;
+		}
+	}
+
 err_free:
 	kfree(buf);
 	return ret;
@@ -1282,7 +1314,8 @@
 		goto err_stop;
 	}
 
-	if (hdev->product == USB_DEVICE_ID_SONY_PS5_CONTROLLER) {
+	if (hdev->product == USB_DEVICE_ID_SONY_PS5_CONTROLLER ||
+		hdev->product == USB_DEVICE_ID_SONY_PS5_CONTROLLER_2) {
 		dev = dualsense_create(hdev);
 		if (IS_ERR(dev)) {
 			hid_err(hdev, "Failed to create dualsense.\n");
@@ -1320,6 +1353,8 @@
 static const struct hid_device_id ps_devices[] = {
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS5_CONTROLLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS5_CONTROLLER) },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS5_CONTROLLER_2) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS5_CONTROLLER_2) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, ps_devices);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-prodikeys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-prodikeys.c
@@ -798,12 +798,18 @@
 static int pk_probe(struct hid_device *hdev, const struct hid_device_id *id)
 {
 	int ret;
-	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
-	unsigned short ifnum = intf->cur_altsetting->desc.bInterfaceNumber;
+	struct usb_interface *intf;
+	unsigned short ifnum;
 	unsigned long quirks = id->driver_data;
 	struct pk_device *pk;
 	struct pcmidi_snd *pm = NULL;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
+	intf = to_usb_interface(hdev->dev.parent);
+	ifnum = intf->cur_altsetting->desc.bInterfaceNumber;
+
 	pk = kzalloc(sizeof(*pk), GFP_KERNEL);
 	if (pk == NULL) {
 		hid_err(hdev, "can't alloc descriptor\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-quirks.c
@@ -33,6 +33,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_AKAI, USB_DEVICE_ID_AKAI_MPKMINI2), HID_QUIRK_NO_INIT_REPORTS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ALPS, USB_DEVICE_ID_IBM_GAMEPAD), HID_QUIRK_BADPAD },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_AMI, USB_DEVICE_ID_AMI_VIRT_KEYBOARD_AND_MOUSE), HID_QUIRK_ALWAYS_POLL },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_ALU_REVB_ANSI), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_2PORTKVM), HID_QUIRK_NOGET },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVMC), HID_QUIRK_NOGET },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVM), HID_QUIRK_NOGET },
@@ -66,6 +67,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CORSAIR, USB_DEVICE_ID_CORSAIR_STRAFE), HID_QUIRK_NO_INIT_REPORTS | HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CREATIVELABS, USB_DEVICE_ID_CREATIVE_SB_OMNI_SURROUND_51), HID_QUIRK_NOGET },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_DELL, USB_DEVICE_ID_DELL_PIXART_USB_OPTICAL_MOUSE), HID_QUIRK_ALWAYS_POLL },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_DELL, USB_DEVICE_ID_DELL_PRO_WIRELESS_KM5221W), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_DMI, USB_DEVICE_ID_DMI_ENC), HID_QUIRK_NOGET },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_DRACAL_RAPHNET, USB_DEVICE_ID_RAPHNET_2NES2SNES), HID_QUIRK_MULTI_INPUT },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_DRACAL_RAPHNET, USB_DEVICE_ID_RAPHNET_4NES4SNES), HID_QUIRK_MULTI_INPUT },
@@ -96,6 +98,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT, USB_DEVICE_ID_HOLTEK_ALT_KEYBOARD_A096), HID_QUIRK_NO_INIT_REPORTS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HOLTEK_ALT, USB_DEVICE_ID_HOLTEK_ALT_KEYBOARD_A293), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HP, USB_PRODUCT_ID_HP_LOGITECH_OEM_USB_OPTICAL_MOUSE_0A4A), HID_QUIRK_ALWAYS_POLL },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_HP, USB_PRODUCT_ID_HP_ELITE_PRESENTER_MOUSE_464A), HID_QUIRK_MULTI_INPUT },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HP, USB_PRODUCT_ID_HP_LOGITECH_OEM_USB_OPTICAL_MOUSE_0B4A), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HP, USB_PRODUCT_ID_HP_PIXART_OEM_USB_OPTICAL_MOUSE), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_HP, USB_PRODUCT_ID_HP_PIXART_OEM_USB_OPTICAL_MOUSE_094A), HID_QUIRK_ALWAYS_POLL },
@@ -122,8 +125,10 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_MOUSE_C05A), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_MOUSE_C06A), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MCS, USB_DEVICE_ID_MCS_GAMEPADBLOCK), HID_QUIRK_MULTI_INPUT },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_MOUSE_0783), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_PIXART_MOUSE), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_POWER_COVER), HID_QUIRK_NO_INIT_REPORTS },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_SURFACE3_COVER), HID_QUIRK_NO_INIT_REPORTS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_SURFACE_PRO_2), HID_QUIRK_NO_INIT_REPORTS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_TOUCH_COVER_2), HID_QUIRK_NO_INIT_REPORTS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_TYPE_COVER_2), HID_QUIRK_NO_INIT_REPORTS },
@@ -145,6 +150,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN), HID_QUIRK_NO_INIT_REPORTS },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_USB_OPTICAL_MOUSE), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_MOUSE_4D22), HID_QUIRK_ALWAYS_POLL },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_MOUSE_4E2A), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_PIXART_MOUSE_4D0F), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_PIXART_MOUSE_4D65), HID_QUIRK_ALWAYS_POLL },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_PIXART_MOUSE_4E22), HID_QUIRK_ALWAYS_POLL },
@@ -186,6 +192,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_TURBOX, USB_DEVICE_ID_TURBOX_KEYBOARD), HID_QUIRK_NOGET },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UCLOGIC_TABLET_KNA5), HID_QUIRK_MULTI_INPUT },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UCLOGIC_TABLET_TWA60), HID_QUIRK_MULTI_INPUT },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_UGTIZER, USB_DEVICE_ID_UGTIZER_TABLET_WP5540), HID_QUIRK_MULTI_INPUT },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_WALTOP, USB_DEVICE_ID_WALTOP_MEDIA_TABLET_10_6_INCH), HID_QUIRK_MULTI_INPUT },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_WALTOP, USB_DEVICE_ID_WALTOP_MEDIA_TABLET_14_1_INCH), HID_QUIRK_MULTI_INPUT },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_WALTOP, USB_DEVICE_ID_WALTOP_SIRIUS_BATTERY_FREE_TABLET), HID_QUIRK_MULTI_INPUT },
@@ -302,6 +309,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MAGIC_KEYBOARD_ANSI) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_MAGIC_KEYBOARD_2021) },
 #endif
 #if IS_ENABLED(CONFIG_HID_APPLEIR)
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_IRCONTROL) },
@@ -377,7 +385,8 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_DT1URBK) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_DT1DRBK) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1URBK) },
-	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1DRBK) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1DRBK_010D) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ELECOM, USB_DEVICE_ID_ELECOM_M_HT1DRBK_011C) },
 #endif
 #if IS_ENABLED(CONFIG_HID_ELO)
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ELO, 0x0009) },
@@ -606,6 +615,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_MMO7) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MADCATZ, USB_DEVICE_ID_MADCATZ_RAT5) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MADCATZ, USB_DEVICE_ID_MADCATZ_RAT9) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MADCATZ, USB_DEVICE_ID_MADCATZ_MMO7) },
 #endif
 #if IS_ENABLED(CONFIG_HID_SAMSUNG)
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_IR_REMOTE) },
@@ -861,6 +871,7 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SYNAPTICS, USB_DEVICE_ID_SYNAPTICS_DPAD) },
 #endif
 	{ HID_USB_DEVICE(USB_VENDOR_ID_YEALINK, USB_DEVICE_ID_YEALINK_P1K_P4K_B2K) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_QUANTA_HP_5MP_CAMERA_5473) },
 	{ }
 };
 
@@ -1211,7 +1222,7 @@
 static unsigned long hid_gets_squirk(const struct hid_device *hdev)
 {
 	const struct hid_device_id *bl_entry;
-	unsigned long quirks = 0;
+	unsigned long quirks = hdev->initial_quirks;
 
 	if (hid_match_id(hdev, hid_ignore_list))
 		quirks |= HID_QUIRK_IGNORE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-arvo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-arvo.c
@@ -344,6 +344,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-isku.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-isku.c
@@ -324,6 +324,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-kone.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-kone.c
@@ -749,6 +749,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-koneplus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-koneplus.c
@@ -431,6 +431,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-konepure.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-konepure.c
@@ -133,6 +133,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-kovaplus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-kovaplus.c
@@ -501,6 +501,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-lua.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-lua.c
@@ -160,6 +160,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-pyra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-pyra.c
@@ -449,6 +449,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-ryos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-ryos.c
@@ -141,6 +141,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat-savu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat-savu.c
@@ -113,6 +113,9 @@
 {
 	int retval;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	retval = hid_parse(hdev);
 	if (retval) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-roccat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-roccat.c
@@ -257,6 +257,8 @@
 	if (!new_value)
 		return -ENOMEM;
 
+	mutex_lock(&device->cbuf_lock);
+
 	report = &device->cbuf[device->cbuf_end];
 
 	/* passing NULL is safe */
@@ -276,6 +278,8 @@
 			reader->cbuf_start = (reader->cbuf_start + 1) % ROCCAT_CBUF_SIZE;
 	}
 
+	mutex_unlock(&device->cbuf_lock);
+
 	wake_up_interruptible(&device->wait);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-saitek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-saitek.c
@@ -187,6 +187,8 @@
 		.driver_data = SAITEK_RELEASE_MODE_RAT7 },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_MMO7),
 		.driver_data = SAITEK_RELEASE_MODE_MMO7 },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MADCATZ, USB_DEVICE_ID_MADCATZ_MMO7),
+		.driver_data = SAITEK_RELEASE_MODE_MMO7 },
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-samsung.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-samsung.c
@@ -152,6 +152,9 @@
 	int ret;
 	unsigned int cmask = HID_CONNECT_DEFAULT;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	ret = hid_parse(hdev);
 	if (ret) {
 		hid_err(hdev, "parse failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-sensor-custom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-sensor-custom.c
@@ -62,7 +62,7 @@
 	u32 raw_len;
 } __packed;
 
-static struct attribute hid_custom_attrs[] = {
+static struct attribute hid_custom_attrs[HID_CUSTOM_TOTAL_ATTRS] = {
 	{.name = "name", .mode = S_IRUGO},
 	{.name = "units", .mode = S_IRUGO},
 	{.name = "unit-expo", .mode = S_IRUGO},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-sensor-hub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-sensor-hub.c
@@ -728,23 +728,30 @@
 	return ret;
 }
 
+static int sensor_hub_finalize_pending_fn(struct device *dev, void *data)
+{
+	struct hid_sensor_hub_device *hsdev = dev->platform_data;
+
+	if (hsdev->pending.status)
+		complete(&hsdev->pending.ready);
+
+	return 0;
+}
+
 static void sensor_hub_remove(struct hid_device *hdev)
 {
 	struct sensor_hub_data *data = hid_get_drvdata(hdev);
 	unsigned long flags;
-	int i;
 
 	hid_dbg(hdev, " hardware removed\n");
 	hid_hw_close(hdev);
 	hid_hw_stop(hdev);
+
 	spin_lock_irqsave(&data->lock, flags);
-	for (i = 0; i < data->hid_sensor_client_cnt; ++i) {
-		struct hid_sensor_hub_device *hsdev =
-			data->hid_sensor_hub_client_devs[i].platform_data;
-		if (hsdev->pending.status)
-			complete(&hsdev->pending.ready);
-	}
+	device_for_each_child(&hdev->dev, NULL,
+			      sensor_hub_finalize_pending_fn);
 	spin_unlock_irqrestore(&data->lock, flags);
+
 	mfd_remove_devices(&hdev->dev);
 	mutex_destroy(&data->mutex);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-sony.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-sony.c
@@ -3000,7 +3000,6 @@
 	sc->quirks = quirks;
 	hid_set_drvdata(hdev, sc);
 	sc->hdev = hdev;
-	usbdev = to_usb_device(sc->hdev->dev.parent->parent);
 
 	ret = hid_parse(hdev);
 	if (ret) {
@@ -3038,14 +3037,23 @@
 	 */
 	if (!(hdev->claimed & HID_CLAIMED_INPUT)) {
 		hid_err(hdev, "failed to claim input\n");
-		hid_hw_stop(hdev);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto err;
 	}
 
 	if (sc->quirks & (GHL_GUITAR_PS3WIIU | GHL_GUITAR_PS4)) {
+		if (!hid_is_usb(hdev)) {
+			ret = -EINVAL;
+			goto err;
+		}
+
+		usbdev = to_usb_device(sc->hdev->dev.parent->parent);
+
 		sc->ghl_urb = usb_alloc_urb(0, GFP_ATOMIC);
-		if (!sc->ghl_urb)
-			return -ENOMEM;
+		if (!sc->ghl_urb) {
+			ret = -ENOMEM;
+			goto err;
+		}
 
 		if (sc->quirks & GHL_GUITAR_PS3WIIU)
 			ret = ghl_init_urb(sc, usbdev, ghl_ps3wiiu_magic_data,
@@ -3055,7 +3063,7 @@
 							   ARRAY_SIZE(ghl_ps4_magic_data));
 		if (ret) {
 			hid_err(hdev, "error preparing URB\n");
-			return ret;
+			goto err;
 		}
 
 		timer_setup(&sc->ghl_poke_timer, ghl_magic_poke, 0);
@@ -3064,6 +3072,12 @@
 	}
 
 	return ret;
+
+err:
+	usb_free_urb(sc->ghl_urb);
+
+	hid_hw_stop(hdev);
+	return ret;
 }
 
 static void sony_remove(struct hid_device *hdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-steam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-steam.c
@@ -134,6 +134,11 @@
 	int ret;
 
 	r = steam->hdev->report_enum[HID_FEATURE_REPORT].report_id_hash[0];
+	if (!r) {
+		hid_err(steam->hdev, "No HID_FEATURE_REPORT submitted -  nothing to read\n");
+		return -EINVAL;
+	}
+
 	if (hid_report_len(r) < 64)
 		return -EINVAL;
 
@@ -165,6 +170,11 @@
 	int ret;
 
 	r = steam->hdev->report_enum[HID_FEATURE_REPORT].report_id_hash[0];
+	if (!r) {
+		hid_err(steam->hdev, "No HID_FEATURE_REPORT submitted -  nothing to read\n");
+		return -EINVAL;
+	}
+
 	if (hid_report_len(r) < 64)
 		return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-thrustmaster.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-thrustmaster.c
@@ -64,13 +64,16 @@
  */
 static const struct tm_wheel_info tm_wheels_infos[] = {
 	{0x0306, 0x0006, "Thrustmaster T150RS"},
+	{0x0200, 0x0005, "Thrustmaster T300RS (Missing Attachment)"},
 	{0x0206, 0x0005, "Thrustmaster T300RS"},
+	{0x0209, 0x0005, "Thrustmaster T300RS (Open Wheel Attachment)"},
+	{0x020a, 0x0005, "Thrustmaster T300RS (Sparco R383 Mod)"},
 	{0x0204, 0x0005, "Thrustmaster T300 Ferrari Alcantara Edition"},
 	{0x0002, 0x0002, "Thrustmaster T500RS"}
 	//{0x0407, 0x0001, "Thrustmaster TMX"}
 };
 
-static const uint8_t tm_wheels_infos_length = 4;
+static const uint8_t tm_wheels_infos_length = 7;
 
 /*
  * This structs contains (in little endian) the response data
@@ -158,6 +161,12 @@
 		return;
 	}
 
+	if (usbif->cur_altsetting->desc.bNumEndpoints < 2) {
+		kfree(send_buf);
+		hid_err(hdev, "Wrong number of endpoints?\n");
+		return;
+	}
+
 	ep = &usbif->cur_altsetting->endpoint[1];
 	b_ep = ep->desc.bEndpointAddress;
 
@@ -274,6 +283,9 @@
 	int ret = 0;
 	struct tm_wheel *tm_wheel = 0;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	ret = hid_parse(hdev);
 	if (ret) {
 		hid_err(hdev, "parse failed with error %d\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-u2fzero.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-u2fzero.c
@@ -132,7 +132,7 @@
 
 	ret = (wait_for_completion_timeout(
 		&ctx.done, msecs_to_jiffies(USB_CTRL_SET_TIMEOUT)));
-	if (ret < 0) {
+	if (ret == 0) {
 		usb_kill_urb(dev->urb);
 		hid_err(hdev, "urb submission timed out");
 	} else {
@@ -191,6 +191,8 @@
 	struct u2f_hid_msg resp;
 	int ret;
 	size_t actual_length;
+	/* valid packets must have a correct header */
+	int min_length = offsetof(struct u2f_hid_msg, init.data);
 
 	if (!dev->present) {
 		hid_dbg(dev->hdev, "device not present");
@@ -200,12 +202,12 @@
 	ret = u2fzero_recv(dev, &req, &resp);
 
 	/* ignore errors or packets without data */
-	if (ret < offsetof(struct u2f_hid_msg, init.data))
+	if (ret < min_length)
 		return 0;
 
 	/* only take the minimum amount of data it is safe to take */
-	actual_length = min3((size_t)ret - offsetof(struct u2f_hid_msg,
-		init.data), U2F_HID_MSG_LEN(resp), max);
+	actual_length = min3((size_t)ret - min_length,
+		U2F_HID_MSG_LEN(resp), max);
 
 	memcpy(data, resp.init.data, actual_length);
 
@@ -288,7 +290,7 @@
 	unsigned int minor;
 	int ret;
 
-	if (!hid_is_using_ll_driver(hdev, &usb_hid_driver))
+	if (!hid_is_usb(hdev))
 		return -EINVAL;
 
 	dev = devm_kzalloc(&hdev->dev, sizeof(*dev), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-uclogic-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-uclogic-core.c
@@ -164,11 +164,15 @@
 	struct uclogic_drvdata *drvdata = NULL;
 	bool params_initialized = false;
 
+	if (!hid_is_usb(hdev))
+		return -EINVAL;
+
 	/*
 	 * libinput requires the pad interface to be on a different node
 	 * than the pen, so use QUIRK_MULTI_INPUT for all tablets.
 	 */
 	hdev->quirks |= HID_QUIRK_MULTI_INPUT;
+	hdev->quirks |= HID_QUIRK_HIDINPUT_FORCE;
 
 	/* Allocate and assign driver data */
 	drvdata = devm_kzalloc(&hdev->dev, sizeof(*drvdata), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-uclogic-params.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-uclogic-params.c
@@ -66,7 +66,7 @@
 					__u8 idx, size_t len)
 {
 	int rc;
-	struct usb_device *udev = hid_to_usb_dev(hdev);
+	struct usb_device *udev;
 	__u8 *buf = NULL;
 
 	/* Check arguments */
@@ -75,6 +75,8 @@
 		goto cleanup;
 	}
 
+	udev = hid_to_usb_dev(hdev);
+
 	buf = kmalloc(len, GFP_KERNEL);
 	if (buf == NULL) {
 		rc = -ENOMEM;
@@ -450,7 +452,7 @@
 {
 	int rc;
 	bool found = false;
-	struct usb_device *usb_dev = hid_to_usb_dev(hdev);
+	struct usb_device *usb_dev;
 	char *str_buf = NULL;
 	const size_t str_len = 16;
 
@@ -460,6 +462,8 @@
 		goto cleanup;
 	}
 
+	usb_dev = hid_to_usb_dev(hdev);
+
 	/*
 	 * Enable generic button mode
 	 */
@@ -707,9 +711,9 @@
 				     struct hid_device *hdev)
 {
 	int rc;
-	struct usb_device *udev = hid_to_usb_dev(hdev);
-	struct usb_interface *iface = to_usb_interface(hdev->dev.parent);
-	__u8 bInterfaceNumber = iface->cur_altsetting->desc.bInterfaceNumber;
+	struct usb_device *udev;
+	struct usb_interface *iface;
+	__u8 bInterfaceNumber;
 	bool found;
 	/* The resulting parameters (noop) */
 	struct uclogic_params p = {0, };
@@ -723,6 +727,10 @@
 		goto cleanup;
 	}
 
+	udev = hid_to_usb_dev(hdev);
+	iface = to_usb_interface(hdev->dev.parent);
+	bInterfaceNumber = iface->cur_altsetting->desc.bInterfaceNumber;
+
 	/* If it's not a pen interface */
 	if (bInterfaceNumber != 0) {
 		/* TODO: Consider marking the interface invalid */
@@ -834,21 +842,25 @@
 			struct hid_device *hdev)
 {
 	int rc;
-	struct usb_device *udev = hid_to_usb_dev(hdev);
-	__u8  bNumInterfaces = udev->config->desc.bNumInterfaces;
-	struct usb_interface *iface = to_usb_interface(hdev->dev.parent);
-	__u8 bInterfaceNumber = iface->cur_altsetting->desc.bInterfaceNumber;
+	struct usb_device *udev;
+	__u8  bNumInterfaces;
+	struct usb_interface *iface;
+	__u8 bInterfaceNumber;
 	bool found;
 	/* The resulting parameters (noop) */
 	struct uclogic_params p = {0, };
 
 	/* Check arguments */
-	if (params == NULL || hdev == NULL ||
-	    !hid_is_using_ll_driver(hdev, &usb_hid_driver)) {
+	if (params == NULL || hdev == NULL || !hid_is_usb(hdev)) {
 		rc = -EINVAL;
 		goto cleanup;
 	}
 
+	udev = hid_to_usb_dev(hdev);
+	bNumInterfaces = udev->config->desc.bNumInterfaces;
+	iface = to_usb_interface(hdev->dev.parent);
+	bInterfaceNumber = iface->cur_altsetting->desc.bInterfaceNumber;
+
 	/*
 	 * Set replacement report descriptor if the original matches the
 	 * specified size. Otherwise keep interface unchanged.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hid-vivaldi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hid-vivaldi.c
@@ -57,6 +57,9 @@
 	int ret;
 
 	drvdata = devm_kzalloc(&hdev->dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata)
+		return -ENOMEM;
+
 	hid_set_drvdata(hdev, drvdata);
 
 	ret = hid_parse(hdev);
@@ -71,10 +74,11 @@
 				    struct hid_usage *usage)
 {
 	struct vivaldi_data *drvdata = hid_get_drvdata(hdev);
+	struct hid_report *report = field->report;
 	int fn_key;
 	int ret;
 	u32 report_len;
-	u8 *buf;
+	u8 *report_data, *buf;
 
 	if (field->logical != HID_USAGE_FN_ROW_PHYSMAP ||
 	    (usage->hid & HID_USAGE_PAGE) != HID_UP_ORDINAL)
@@ -86,12 +90,24 @@
 	if (fn_key > drvdata->max_function_row_key)
 		drvdata->max_function_row_key = fn_key;
 
-	buf = hid_alloc_report_buf(field->report, GFP_KERNEL);
-	if (!buf)
+	report_data = buf = hid_alloc_report_buf(report, GFP_KERNEL);
+	if (!report_data)
 		return;
 
-	report_len = hid_report_len(field->report);
-	ret = hid_hw_raw_request(hdev, field->report->id, buf,
+	report_len = hid_report_len(report);
+	if (!report->id) {
+		/*
+		 * hid_hw_raw_request() will stuff report ID (which will be 0)
+		 * into the first byte of the buffer even for unnumbered
+		 * reports, so we need to account for this to avoid getting
+		 * -EOVERFLOW in return.
+		 * Note that hid_alloc_report_buf() adds 7 bytes to the size
+		 * so we can safely say that we have space for an extra byte.
+		 */
+		report_len++;
+	}
+
+	ret = hid_hw_raw_request(hdev, report->id, report_data,
 				 report_len, HID_FEATURE_REPORT,
 				 HID_REQ_GET_REPORT);
 	if (ret < 0) {
@@ -100,7 +116,16 @@
 		goto out;
 	}
 
-	ret = hid_report_raw_event(hdev, HID_FEATURE_REPORT, buf,
+	if (!report->id) {
+		/*
+		 * Undo the damage from hid_hw_raw_request() for unnumbered
+		 * reports.
+		 */
+		report_data++;
+		report_len--;
+	}
+
+	ret = hid_report_raw_event(hdev, HID_FEATURE_REPORT, report_data,
 				   report_len, 0);
 	if (ret) {
 		dev_warn(&hdev->dev, "failed to report feature %d\n",
@@ -118,7 +143,7 @@
 static int vivaldi_input_configured(struct hid_device *hdev,
 				    struct hid_input *hidinput)
 {
-	return sysfs_create_group(&hdev->dev.kobj, &input_attribute_group);
+	return devm_device_add_group(&hdev->dev, &input_attribute_group);
 }
 
 static const struct hid_device_id vivaldi_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/hidraw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/hidraw.c
@@ -346,10 +346,13 @@
 	unsigned int minor = iminor(inode);
 	struct hidraw_list *list = file->private_data;
 	unsigned long flags;
+	int i;
 
 	mutex_lock(&minors_lock);
 
 	spin_lock_irqsave(&hidraw_table[minor]->list_lock, flags);
+	for (i = list->tail; i < list->head; i++)
+		kfree(list->buffer[i].value);
 	list_del(&list->node);
 	spin_unlock_irqrestore(&hidraw_table[minor]->list_lock, flags);
 	kfree(list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/i2c-hid/i2c-hid-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/i2c-hid/i2c-hid-acpi.c
@@ -111,7 +111,7 @@
 	}
 
 	return i2c_hid_core_probe(client, &ihid_acpi->ops,
-				  hid_descriptor_address);
+				  hid_descriptor_address, 0);
 }
 
 static const struct acpi_device_id i2c_hid_acpi_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/i2c-hid/i2c-hid-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/i2c-hid/i2c-hid-core.c
@@ -51,7 +51,6 @@
 /* flags */
 #define I2C_HID_STARTED		0
 #define I2C_HID_RESET_PENDING	1
-#define I2C_HID_READ_PENDING	2
 
 #define I2C_HID_PWR_ON		0x00
 #define I2C_HID_PWR_SLEEP	0x01
@@ -251,7 +250,6 @@
 		msg[1].len = data_len;
 		msg[1].buf = buf_recv;
 		msg_num = 2;
-		set_bit(I2C_HID_READ_PENDING, &ihid->flags);
 	}
 
 	if (wait)
@@ -259,9 +257,6 @@
 
 	ret = i2c_transfer(client->adapter, msg, msg_num);
 
-	if (data_len > 0)
-		clear_bit(I2C_HID_READ_PENDING, &ihid->flags);
-
 	if (ret != msg_num)
 		return ret < 0 ? ret : -EIO;
 
@@ -533,9 +528,6 @@
 {
 	struct i2c_hid *ihid = dev_id;
 
-	if (test_bit(I2C_HID_READ_PENDING, &ihid->flags))
-		return IRQ_HANDLED;
-
 	i2c_hid_get_input(ihid);
 
 	return IRQ_HANDLED;
@@ -615,6 +607,17 @@
 	if (report_type == HID_OUTPUT_REPORT)
 		return -EINVAL;
 
+	/*
+	 * In case of unnumbered reports the response from the device will
+	 * not have the report ID that the upper layers expect, so we need
+	 * to stash it the buffer ourselves and adjust the data size.
+	 */
+	if (!report_number) {
+		buf[0] = 0;
+		buf++;
+		count--;
+	}
+
 	/* +2 bytes to include the size of the reply in the query buffer */
 	ask_count = min(count + 2, (size_t)ihid->bufsize);
 
@@ -636,6 +639,9 @@
 	count = min(count, ret_count - 2);
 	memcpy(buf, ihid->rawbuf + 2, count);
 
+	if (!report_number)
+		count++;
+
 	return count;
 }
 
@@ -652,17 +658,19 @@
 
 	mutex_lock(&ihid->reset_lock);
 
-	if (report_id) {
-		buf++;
-		count--;
-	}
-
+	/*
+	 * Note that both numbered and unnumbered reports passed here
+	 * are supposed to have report ID stored in the 1st byte of the
+	 * buffer, so we strip it off unconditionally before passing payload
+	 * to i2c_hid_set_or_send_report which takes care of encoding
+	 * everything properly.
+	 */
 	ret = i2c_hid_set_or_send_report(client,
 				report_type == HID_FEATURE_REPORT ? 0x03 : 0x02,
-				report_id, buf, count, use_data);
+				report_id, buf + 1, count - 1, use_data);
 
-	if (report_id && ret >= 0)
-		ret++; /* add report_id to the number of transfered bytes */
+	if (ret >= 0)
+		ret++; /* add report_id to the number of transferred bytes */
 
 	mutex_unlock(&ihid->reset_lock);
 
@@ -912,7 +920,7 @@
 }
 
 int i2c_hid_core_probe(struct i2c_client *client, struct i2chid_ops *ops,
-		       u16 hid_descriptor_address)
+		       u16 hid_descriptor_address, u32 quirks)
 {
 	int ret;
 	struct i2c_hid *ihid;
@@ -996,6 +1004,10 @@
 	hid->vendor = le16_to_cpu(ihid->hdesc.wVendorID);
 	hid->product = le16_to_cpu(ihid->hdesc.wProductID);
 
+	hid->initial_quirks = quirks;
+	hid->initial_quirks |= i2c_hid_get_dmi_quirks(hid->vendor,
+						      hid->product);
+
 	snprintf(hid->name, sizeof(hid->name), "%s %04X:%04X",
 		 client->name, (u16)hid->vendor, (u16)hid->product);
 	strlcpy(hid->phys, dev_name(&client->dev), sizeof(hid->phys));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/i2c-hid/i2c-hid-dmi-quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/i2c-hid/i2c-hid-dmi-quirks.c
@@ -10,8 +10,10 @@
 #include <linux/types.h>
 #include <linux/dmi.h>
 #include <linux/mod_devicetable.h>
+#include <linux/hid.h>
 
 #include "i2c-hid.h"
+#include "../hid-ids.h"
 
 
 struct i2c_hid_desc_override {
@@ -416,6 +418,28 @@
 	{ }	/* Terminate list */
 };
 
+static const struct hid_device_id i2c_hid_elan_flipped_quirks = {
+	HID_DEVICE(BUS_I2C, HID_GROUP_MULTITOUCH_WIN_8, USB_VENDOR_ID_ELAN, 0x2dcd),
+		HID_QUIRK_X_INVERT | HID_QUIRK_Y_INVERT
+};
+
+/*
+ * This list contains devices which have specific issues based on the system
+ * they're on and not just the device itself. The driver_data will have a
+ * specific hid device to match against.
+ */
+static const struct dmi_system_id i2c_hid_dmi_quirk_table[] = {
+	{
+		.ident = "DynaBook K50/FR",
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Dynabook Inc."),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "dynabook K50/FR"),
+		},
+		.driver_data = (void *)&i2c_hid_elan_flipped_quirks,
+	},
+	{ }	/* Terminate list */
+};
+
 
 struct i2c_hid_desc *i2c_hid_get_dmi_i2c_hid_desc_override(uint8_t *i2c_name)
 {
@@ -450,3 +474,21 @@
 	*size = override->hid_report_desc_size;
 	return override->hid_report_desc;
 }
+
+u32 i2c_hid_get_dmi_quirks(const u16 vendor, const u16 product)
+{
+	u32 quirks = 0;
+	const struct dmi_system_id *system_id =
+			dmi_first_match(i2c_hid_dmi_quirk_table);
+
+	if (system_id) {
+		const struct hid_device_id *device_id =
+				(struct hid_device_id *)(system_id->driver_data);
+
+		if (device_id && device_id->vendor == vendor &&
+		    device_id->product == product)
+			quirks = device_id->driver_data;
+	}
+
+	return quirks;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/i2c-hid/i2c-hid-of-goodix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/i2c-hid/i2c-hid-of-goodix.c
@@ -27,7 +27,6 @@
 
 	struct regulator *vdd;
 	struct notifier_block nb;
-	struct mutex regulator_mutex;
 	struct gpio_desc *reset_gpio;
 	const struct goodix_i2c_hid_timing_data *timings;
 };
@@ -67,8 +66,6 @@
 		container_of(nb, struct i2c_hid_of_goodix, nb);
 	int ret = NOTIFY_OK;
 
-	mutex_lock(&ihid_goodix->regulator_mutex);
-
 	switch (event) {
 	case REGULATOR_EVENT_PRE_DISABLE:
 		gpiod_set_value_cansleep(ihid_goodix->reset_gpio, 1);
@@ -87,8 +84,6 @@
 		break;
 	}
 
-	mutex_unlock(&ihid_goodix->regulator_mutex);
-
 	return ret;
 }
 
@@ -102,8 +97,6 @@
 	if (!ihid_goodix)
 		return -ENOMEM;
 
-	mutex_init(&ihid_goodix->regulator_mutex);
-
 	ihid_goodix->ops.power_up = goodix_i2c_hid_power_up;
 	ihid_goodix->ops.power_down = goodix_i2c_hid_power_down;
 
@@ -130,27 +123,30 @@
 	 *   long. Holding the controller in reset apparently draws extra
 	 *   power.
 	 */
-	mutex_lock(&ihid_goodix->regulator_mutex);
 	ihid_goodix->nb.notifier_call = ihid_goodix_vdd_notify;
 	ret = devm_regulator_register_notifier(ihid_goodix->vdd, &ihid_goodix->nb);
-	if (ret) {
-		mutex_unlock(&ihid_goodix->regulator_mutex);
+	if (ret)
 		return dev_err_probe(&client->dev, ret,
 			"regulator notifier request failed\n");
-	}
 
 	/*
 	 * If someone else is holding the regulator on (or the regulator is
 	 * an always-on one) we might never be told to deassert reset. Do it
-	 * now. Here we'll assume that someone else might have _just
-	 * barely_ turned the regulator on so we'll do the full
-	 * "post_power_delay" just in case.
+	 * now... and temporarily bump the regulator reference count just to
+	 * make sure it is impossible for this to race with our own notifier!
+	 * We also assume that someone else might have _just barely_ turned
+	 * the regulator on so we'll do the full "post_power_delay" just in
+	 * case.
 	 */
-	if (ihid_goodix->reset_gpio && regulator_is_enabled(ihid_goodix->vdd))
+	if (ihid_goodix->reset_gpio && regulator_is_enabled(ihid_goodix->vdd)) {
+		ret = regulator_enable(ihid_goodix->vdd);
+		if (ret)
+			return ret;
 		goodix_i2c_hid_deassert_reset(ihid_goodix, true);
-	mutex_unlock(&ihid_goodix->regulator_mutex);
+		regulator_disable(ihid_goodix->vdd);
+	}
 
-	return i2c_hid_core_probe(client, &ihid_goodix->ops, 0x0001);
+	return i2c_hid_core_probe(client, &ihid_goodix->ops, 0x0001, 0);
 }
 
 static const struct goodix_i2c_hid_timing_data goodix_gt7375p_timing_data = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/i2c-hid/i2c-hid-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/i2c-hid/i2c-hid-of.c
@@ -21,6 +21,7 @@
 
 #include <linux/delay.h>
 #include <linux/device.h>
+#include <linux/hid.h>
 #include <linux/i2c.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -71,6 +72,7 @@
 	struct device *dev = &client->dev;
 	struct i2c_hid_of *ihid_of;
 	u16 hid_descriptor_address;
+	u32 quirks = 0;
 	int ret;
 	u32 val;
 
@@ -78,6 +80,7 @@
 	if (!ihid_of)
 		return -ENOMEM;
 
+	ihid_of->client = client;
 	ihid_of->ops.power_up = i2c_hid_of_power_up;
 	ihid_of->ops.power_down = i2c_hid_of_power_down;
 
@@ -105,8 +108,14 @@
 	if (ret)
 		return ret;
 
+	if (device_property_read_bool(dev, "touchscreen-inverted-x"))
+		quirks |= HID_QUIRK_X_INVERT;
+
+	if (device_property_read_bool(dev, "touchscreen-inverted-y"))
+		quirks |= HID_QUIRK_Y_INVERT;
+
 	return i2c_hid_core_probe(client, &ihid_of->ops,
-				  hid_descriptor_address);
+				  hid_descriptor_address, quirks);
 }
 
 static const struct of_device_id i2c_hid_of_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/i2c-hid/i2c-hid.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/i2c-hid/i2c-hid.h
@@ -9,6 +9,7 @@
 struct i2c_hid_desc *i2c_hid_get_dmi_i2c_hid_desc_override(uint8_t *i2c_name);
 char *i2c_hid_get_dmi_hid_report_desc_override(uint8_t *i2c_name,
 					       unsigned int *size);
+u32 i2c_hid_get_dmi_quirks(const u16 vendor, const u16 product);
 #else
 static inline struct i2c_hid_desc
 		   *i2c_hid_get_dmi_i2c_hid_desc_override(uint8_t *i2c_name)
@@ -16,6 +17,8 @@
 static inline char *i2c_hid_get_dmi_hid_report_desc_override(uint8_t *i2c_name,
 							     unsigned int *size)
 { return NULL; }
+static inline u32 i2c_hid_get_dmi_quirks(const u16 vendor, const u16 product)
+{ return 0; }
 #endif
 
 /**
@@ -32,7 +35,7 @@
 };
 
 int i2c_hid_core_probe(struct i2c_client *client, struct i2chid_ops *ops,
-		       u16 hid_descriptor_address);
+		       u16 hid_descriptor_address, u32 quirks);
 int i2c_hid_core_remove(struct i2c_client *client);
 
 void i2c_hid_core_shutdown(struct i2c_client *client);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ipc/ipc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ipc/ipc.c
@@ -5,6 +5,7 @@
  * Copyright (c) 2014-2016, Intel Corporation.
  */
 
+#include <linux/devm-helpers.h>
 #include <linux/sched.h>
 #include <linux/spinlock.h>
 #include <linux/delay.h>
@@ -576,14 +577,14 @@
 static void _ish_sync_fw_clock(struct ishtp_device *dev)
 {
 	static unsigned long	prev_sync;
-	uint64_t	usec;
+	struct ipc_time_update_msg time = {};
 
 	if (prev_sync && jiffies - prev_sync < 20 * HZ)
 		return;
 
 	prev_sync = jiffies;
-	usec = ktime_to_us(ktime_get_boottime());
-	ipc_send_mng_msg(dev, MNG_SYNC_FW_CLOCK, &usec, sizeof(uint64_t));
+	/* The fields of time would be updated while sending message */
+	ipc_send_mng_msg(dev, MNG_SYNC_FW_CLOCK, &time, sizeof(time));
 }
 
 /**
@@ -621,7 +622,6 @@
 	case MNG_RESET_NOTIFY:
 		if (!ishtp_dev) {
 			ishtp_dev = dev;
-			INIT_WORK(&fw_reset_work, fw_reset_work_fn);
 		}
 		schedule_work(&fw_reset_work);
 		break;
@@ -936,6 +936,7 @@
 {
 	struct ishtp_device *dev;
 	int	i;
+	int	ret;
 
 	dev = devm_kzalloc(&pdev->dev,
 			   sizeof(struct ishtp_device) + sizeof(struct ish_hw),
@@ -943,6 +944,7 @@
 	if (!dev)
 		return NULL;
 
+	dev->devc = &pdev->dev;
 	ishtp_device_init(dev);
 
 	init_waitqueue_head(&dev->wait_hw_ready);
@@ -971,8 +973,13 @@
 		list_add_tail(&tx_buf->link, &dev->wr_free_list);
 	}
 
+	ret = devm_work_autocancel(&pdev->dev, &fw_reset_work, fw_reset_work_fn);
+	if (ret) {
+		dev_err(dev->devc, "Failed to initialise FW reset work\n");
+		return NULL;
+	}
+
 	dev->ops = &ish_hw_ops;
-	dev->devc = &pdev->dev;
 	dev->mtu = IPC_PAYLOAD_SIZE - sizeof(struct ishtp_msg_hdr);
 	return dev;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ipc/pci-ish.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ipc/pci-ish.c
@@ -129,6 +129,14 @@
 	}
 	wakeup = &adev->wakeup;
 
+	/*
+	 * Call acpi_disable_gpe(), so that reference count
+	 * gpe_event_info->runtime_count doesn't overflow.
+	 * When gpe_event_info->runtime_count = 0, the call
+	 * to acpi_disable_gpe() simply return.
+	 */
+	acpi_disable_gpe(wakeup->gpe_device, wakeup->gpe_number);
+
 	acpi_sts = acpi_enable_gpe(wakeup->gpe_device, wakeup->gpe_number);
 	if (ACPI_FAILURE(acpi_sts)) {
 		dev_err(dev, "enable ose_gpe failed\n");
@@ -204,6 +212,11 @@
 
 	/* request and enable interrupt */
 	ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
+	if (ret < 0) {
+		dev_err(dev, "ISH: Failed to allocate IRQ vectors\n");
+		return ret;
+	}
+
 	if (!pdev->msi_enabled && !pdev->msix_enabled)
 		irq_flag = IRQF_SHARED;
 
@@ -266,7 +279,8 @@
 
 	if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag
 			&& IPC_IS_ISH_ILUP(fwsts)) {
-		disable_irq_wake(pdev->irq);
+		if (device_may_wakeup(&pdev->dev))
+			disable_irq_wake(pdev->irq);
 
 		ish_set_host_ready(dev);
 
@@ -337,7 +351,8 @@
 			 */
 			pci_save_state(pdev);
 
-			enable_irq_wake(pdev->irq);
+			if (device_may_wakeup(&pdev->dev))
+				enable_irq_wake(pdev->irq);
 		}
 	} else {
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ishtp-fw-loader.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ishtp-fw-loader.c
@@ -631,7 +631,7 @@
 				  const struct firmware *fw,
 				  const struct shim_fw_info fw_info)
 {
-	int rv;
+	int rv = 0;
 	void *dma_buf;
 	dma_addr_t dma_buf_phy;
 	u32 fragment_offset, fragment_size, payload_max_size;
@@ -657,21 +657,12 @@
 	 */
 	payload_max_size &= ~(L1_CACHE_BYTES - 1);
 
-	dma_buf = kmalloc(payload_max_size, GFP_KERNEL | GFP_DMA32);
+	dma_buf = dma_alloc_coherent(devc, payload_max_size, &dma_buf_phy, GFP_KERNEL);
 	if (!dma_buf) {
 		client_data->flag_retry = true;
 		return -ENOMEM;
 	}
 
-	dma_buf_phy = dma_map_single(devc, dma_buf, payload_max_size,
-				     DMA_TO_DEVICE);
-	if (dma_mapping_error(devc, dma_buf_phy)) {
-		dev_err(cl_data_to_dev(client_data), "DMA map failed\n");
-		client_data->flag_retry = true;
-		rv = -ENOMEM;
-		goto end_err_dma_buf_release;
-	}
-
 	ldr_xfer_dma_frag.fragment.hdr.command = LOADER_CMD_XFER_FRAGMENT;
 	ldr_xfer_dma_frag.fragment.xfer_mode = LOADER_XFER_MODE_DIRECT_DMA;
 	ldr_xfer_dma_frag.ddr_phys_addr = (u64)dma_buf_phy;
@@ -691,14 +682,7 @@
 		ldr_xfer_dma_frag.fragment.size = fragment_size;
 		memcpy(dma_buf, &fw->data[fragment_offset], fragment_size);
 
-		dma_sync_single_for_device(devc, dma_buf_phy,
-					   payload_max_size,
-					   DMA_TO_DEVICE);
-
-		/*
-		 * Flush cache here because the dma_sync_single_for_device()
-		 * does not do for x86.
-		 */
+		/* Flush cache to be sure the data is in main memory. */
 		clflush_cache_range(dma_buf, payload_max_size);
 
 		dev_dbg(cl_data_to_dev(client_data),
@@ -721,15 +705,8 @@
 		fragment_offset += fragment_size;
 	}
 
-	dma_unmap_single(devc, dma_buf_phy, payload_max_size, DMA_TO_DEVICE);
-	kfree(dma_buf);
-	return 0;
-
 end_err_resp_buf_release:
-	/* Free ISH buffer if not done already, in error case */
-	dma_unmap_single(devc, dma_buf_phy, payload_max_size, DMA_TO_DEVICE);
-end_err_dma_buf_release:
-	kfree(dma_buf);
+	dma_free_coherent(devc, payload_max_size, dma_buf, dma_buf_phy);
 	return rv;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ishtp-hid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ishtp-hid.c
@@ -261,12 +261,14 @@
  */
 void ishtp_hid_remove(struct ishtp_cl_data *client_data)
 {
+	void *data;
 	int i;
 
 	for (i = 0; i < client_data->num_hid_devices; ++i) {
 		if (client_data->hid_sensor_hubs[i]) {
-			kfree(client_data->hid_sensor_hubs[i]->driver_data);
+			data = client_data->hid_sensor_hubs[i]->driver_data;
 			hid_destroy_device(client_data->hid_sensor_hubs[i]);
+			kfree(data);
 			client_data->hid_sensor_hubs[i] = NULL;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ishtp-hid.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ishtp-hid.h
@@ -105,7 +105,7 @@
  * @multi_packet_cnt:	Count of fragmented packet count
  *
  * This structure is used to store completion flags and per client data like
- * like report description, number of HID devices etc.
+ * report description, number of HID devices etc.
  */
 struct ishtp_cl_data {
 	/* completion flags */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ishtp/client.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ishtp/client.c
@@ -626,13 +626,14 @@
 }
 
 /**
- * ipc_tx_callback() - IPC tx callback function
+ * ipc_tx_send() - IPC tx send function
  * @prm: Pointer to client device instance
  *
- * Send message over IPC either first time or on callback on previous message
- * completion
+ * Send message over IPC. Message will be split into fragments
+ * if message size is bigger than IPC FIFO size, and all
+ * fragments will be sent one by one.
  */
-static void ipc_tx_callback(void *prm)
+static void ipc_tx_send(void *prm)
 {
 	struct ishtp_cl	*cl = prm;
 	struct ishtp_cl_tx_ring	*cl_msg;
@@ -677,32 +678,41 @@
 			    list);
 	rem = cl_msg->send_buf.size - cl->tx_offs;
 
-	ishtp_hdr.host_addr = cl->host_client_id;
-	ishtp_hdr.fw_addr = cl->fw_client_id;
-	ishtp_hdr.reserved = 0;
-	pmsg = cl_msg->send_buf.data + cl->tx_offs;
-
-	if (rem <= dev->mtu) {
-		ishtp_hdr.length = rem;
-		ishtp_hdr.msg_complete = 1;
-		cl->sending = 0;
-		list_del_init(&cl_msg->list);	/* Must be before write */
-		spin_unlock_irqrestore(&cl->tx_list_spinlock, tx_flags);
-		/* Submit to IPC queue with no callback */
-		ishtp_write_message(dev, &ishtp_hdr, pmsg);
-		spin_lock_irqsave(&cl->tx_free_list_spinlock, tx_free_flags);
-		list_add_tail(&cl_msg->list, &cl->tx_free_list.list);
-		++cl->tx_ring_free_size;
-		spin_unlock_irqrestore(&cl->tx_free_list_spinlock,
-			tx_free_flags);
-	} else {
-		/* Send IPC fragment */
-		spin_unlock_irqrestore(&cl->tx_list_spinlock, tx_flags);
-		cl->tx_offs += dev->mtu;
-		ishtp_hdr.length = dev->mtu;
-		ishtp_hdr.msg_complete = 0;
-		ishtp_send_msg(dev, &ishtp_hdr, pmsg, ipc_tx_callback, cl);
+	while (rem > 0) {
+		ishtp_hdr.host_addr = cl->host_client_id;
+		ishtp_hdr.fw_addr = cl->fw_client_id;
+		ishtp_hdr.reserved = 0;
+		pmsg = cl_msg->send_buf.data + cl->tx_offs;
+
+		if (rem <= dev->mtu) {
+			/* Last fragment or only one packet */
+			ishtp_hdr.length = rem;
+			ishtp_hdr.msg_complete = 1;
+			/* Submit to IPC queue with no callback */
+			ishtp_write_message(dev, &ishtp_hdr, pmsg);
+			cl->tx_offs = 0;
+			cl->sending = 0;
+
+			break;
+		} else {
+			/* Send ipc fragment */
+			ishtp_hdr.length = dev->mtu;
+			ishtp_hdr.msg_complete = 0;
+			/* All fregments submitted to IPC queue with no callback */
+			ishtp_write_message(dev, &ishtp_hdr, pmsg);
+			cl->tx_offs += dev->mtu;
+			rem = cl_msg->send_buf.size - cl->tx_offs;
+		}
 	}
+
+	list_del_init(&cl_msg->list);
+	spin_unlock_irqrestore(&cl->tx_list_spinlock, tx_flags);
+
+	spin_lock_irqsave(&cl->tx_free_list_spinlock, tx_free_flags);
+	list_add_tail(&cl_msg->list, &cl->tx_free_list.list);
+	++cl->tx_ring_free_size;
+	spin_unlock_irqrestore(&cl->tx_free_list_spinlock,
+		tx_free_flags);
 }
 
 /**
@@ -720,7 +730,7 @@
 		return;
 
 	cl->tx_offs = 0;
-	ipc_tx_callback(cl);
+	ipc_tx_send(cl);
 	++cl->send_msg_cnt_ipc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/intel-ish-hid/ishtp/dma-if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/intel-ish-hid/ishtp/dma-if.c
@@ -104,6 +104,11 @@
 	int required_slots = (size / DMA_SLOT_SIZE)
 		+ 1 * (size % DMA_SLOT_SIZE != 0);
 
+	if (!dev->ishtp_dma_tx_map) {
+		dev_err(dev->devc, "Fail to allocate Tx map\n");
+		return NULL;
+	}
+
 	spin_lock_irqsave(&dev->ishtp_dma_tx_lock, flags);
 	for (i = 0; i <= (dev->ishtp_dma_num_slots - required_slots); i++) {
 		free = 1;
@@ -150,6 +155,11 @@
 		return;
 	}
 
+	if (!dev->ishtp_dma_tx_map) {
+		dev_err(dev->devc, "Fail to allocate Tx map\n");
+		return;
+	}
+
 	i = (msg_addr - dev->ishtp_host_dma_tx_buf) / DMA_SLOT_SIZE;
 	spin_lock_irqsave(&dev->ishtp_dma_tx_lock, flags);
 	for (j = 0; j < acked_slots; j++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/surface-hid/surface_hid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/surface-hid/surface_hid.c
@@ -209,7 +209,7 @@
 
 	shid->notif.base.priority = 1;
 	shid->notif.base.fn = ssam_hid_event_fn;
-	shid->notif.event.reg = SSAM_EVENT_REGISTRY_REG;
+	shid->notif.event.reg = SSAM_EVENT_REGISTRY_REG(sdev->uid.target);
 	shid->notif.event.id.target_category = sdev->uid.category;
 	shid->notif.event.id.instance = sdev->uid.instance;
 	shid->notif.event.mask = SSAM_EVENT_MASK_STRICT;
@@ -230,7 +230,7 @@
 }
 
 static const struct ssam_device_id surface_hid_match[] = {
-	{ SSAM_SDEV(HID, 0x02, SSAM_ANY_IID, 0x00) },
+	{ SSAM_SDEV(HID, SSAM_ANY_TID, SSAM_ANY_IID, 0x00) },
 	{ },
 };
 MODULE_DEVICE_TABLE(ssam, surface_hid_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/uhid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/uhid.c
@@ -28,11 +28,22 @@
 
 struct uhid_device {
 	struct mutex devlock;
+
+	/* This flag tracks whether the HID device is usable for commands from
+	 * userspace. The flag is already set before hid_add_device(), which
+	 * runs in workqueue context, to allow hid_add_device() to communicate
+	 * with userspace.
+	 * However, if hid_add_device() fails, the flag is cleared without
+	 * holding devlock.
+	 * We guarantee that if @running changes from true to false while you're
+	 * holding @devlock, it's still fine to access @hid.
+	 */
 	bool running;
 
 	__u8 *rd_data;
 	uint rd_size;
 
+	/* When this is NULL, userspace may use UHID_CREATE/UHID_CREATE2. */
 	struct hid_device *hid;
 	struct uhid_event input_buf;
 
@@ -63,9 +74,18 @@
 	if (ret) {
 		hid_err(uhid->hid, "Cannot register HID device: error %d\n", ret);
 
-		hid_destroy_device(uhid->hid);
-		uhid->hid = NULL;
-		uhid->running = false;
+		/* We used to call hid_destroy_device() here, but that's really
+		 * messy to get right because we have to coordinate with
+		 * concurrent writes from userspace that might be in the middle
+		 * of using uhid->hid.
+		 * Just leave uhid->hid as-is for now, and clean it up when
+		 * userspace tries to close or reinitialize the uhid instance.
+		 *
+		 * However, we do have to clear the ->running flag and do a
+		 * wakeup to make sure userspace knows that the device is gone.
+		 */
+		WRITE_ONCE(uhid->running, false);
+		wake_up_interruptible(&uhid->report_wait);
 	}
 }
 
@@ -174,9 +194,9 @@
 	spin_unlock_irqrestore(&uhid->qlock, flags);
 
 	ret = wait_event_interruptible_timeout(uhid->report_wait,
-				!uhid->report_running || !uhid->running,
+				!uhid->report_running || !READ_ONCE(uhid->running),
 				5 * HZ);
-	if (!ret || !uhid->running || uhid->report_running)
+	if (!ret || !READ_ONCE(uhid->running) || uhid->report_running)
 		ret = -EIO;
 	else if (ret < 0)
 		ret = -ERESTARTSYS;
@@ -217,7 +237,7 @@
 	struct uhid_event *ev;
 	int ret;
 
-	if (!uhid->running)
+	if (!READ_ONCE(uhid->running))
 		return -EIO;
 
 	ev = kzalloc(sizeof(*ev), GFP_KERNEL);
@@ -259,7 +279,7 @@
 	struct uhid_event *ev;
 	int ret;
 
-	if (!uhid->running || count > UHID_DATA_MAX)
+	if (!READ_ONCE(uhid->running) || count > UHID_DATA_MAX)
 		return -EIO;
 
 	ev = kzalloc(sizeof(*ev), GFP_KERNEL);
@@ -375,6 +395,7 @@
 	.parse = uhid_hid_parse,
 	.raw_request = uhid_hid_raw_request,
 	.output_report = uhid_hid_output_report,
+	.max_buffer_size = UHID_DATA_MAX,
 };
 EXPORT_SYMBOL_GPL(uhid_hid_driver);
 
@@ -474,7 +495,7 @@
 	void *rd_data;
 	int ret;
 
-	if (uhid->running)
+	if (uhid->hid)
 		return -EALREADY;
 
 	rd_size = ev->u.create2.rd_size;
@@ -556,15 +577,16 @@
 
 static int uhid_dev_destroy(struct uhid_device *uhid)
 {
-	if (!uhid->running)
+	if (!uhid->hid)
 		return -EINVAL;
 
-	uhid->running = false;
+	WRITE_ONCE(uhid->running, false);
 	wake_up_interruptible(&uhid->report_wait);
 
 	cancel_work_sync(&uhid->worker);
 
 	hid_destroy_device(uhid->hid);
+	uhid->hid = NULL;
 	kfree(uhid->rd_data);
 
 	return 0;
@@ -572,7 +594,7 @@
 
 static int uhid_dev_input(struct uhid_device *uhid, struct uhid_event *ev)
 {
-	if (!uhid->running)
+	if (!READ_ONCE(uhid->running))
 		return -EINVAL;
 
 	hid_input_report(uhid->hid, HID_INPUT_REPORT, ev->u.input.data,
@@ -583,7 +605,7 @@
 
 static int uhid_dev_input2(struct uhid_device *uhid, struct uhid_event *ev)
 {
-	if (!uhid->running)
+	if (!READ_ONCE(uhid->running))
 		return -EINVAL;
 
 	hid_input_report(uhid->hid, HID_INPUT_REPORT, ev->u.input2.data,
@@ -595,7 +617,7 @@
 static int uhid_dev_get_report_reply(struct uhid_device *uhid,
 				     struct uhid_event *ev)
 {
-	if (!uhid->running)
+	if (!READ_ONCE(uhid->running))
 		return -EINVAL;
 
 	uhid_report_wake_up(uhid, ev->u.get_report_reply.id, ev);
@@ -605,7 +627,7 @@
 static int uhid_dev_set_report_reply(struct uhid_device *uhid,
 				     struct uhid_event *ev)
 {
-	if (!uhid->running)
+	if (!READ_ONCE(uhid->running))
 		return -EINVAL;
 
 	uhid_report_wake_up(uhid, ev->u.set_report_reply.id, ev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/wacom.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/wacom.h
@@ -91,6 +91,7 @@
 #include <linux/leds.h>
 #include <linux/usb/input.h>
 #include <linux/power_supply.h>
+#include <linux/timer.h>
 #include <asm/unaligned.h>
 
 /*
@@ -152,6 +153,7 @@
 		struct input_dev *input;
 		bool registered;
 		struct wacom_battery battery;
+		ktime_t active_time;
 	} remotes[WACOM_MAX_REMOTES];
 };
 
@@ -167,6 +169,7 @@
 	struct delayed_work init_work;
 	struct wacom_remote *remote;
 	struct work_struct mode_change_work;
+	struct timer_list idleprox_timer;
 	bool generic_has_leds;
 	struct wacom_leds {
 		struct wacom_group_leds *groups;
@@ -239,4 +242,5 @@
 struct wacom_led *wacom_led_next(struct wacom *wacom, struct wacom_led *cur);
 int wacom_equivalent_usage(int usage);
 int wacom_initialize_leds(struct wacom *wacom);
+void wacom_idleprox_timeout(struct timer_list *list);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/wacom_sys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/wacom_sys.c
@@ -160,6 +160,9 @@
 {
 	struct wacom *wacom = hid_get_drvdata(hdev);
 
+	if (wacom->wacom_wac.features.type == BOOTLOADER)
+		return 0;
+
 	if (size > WACOM_PKGLEN_MAX)
 		return 1;
 
@@ -726,7 +729,7 @@
 	 * Skip the query for this type and modify defaults based on
 	 * interface number.
 	 */
-	if (features->type == WIRELESS) {
+	if (features->type == WIRELESS && intf) {
 		if (intf->cur_altsetting->desc.bInterfaceNumber == 0)
 			features->device_type = WACOM_DEVICETYPE_WL_MONITOR;
 		else
@@ -2085,7 +2088,7 @@
 	return 0;
 }
 
-static int wacom_register_inputs(struct wacom *wacom)
+static int wacom_setup_inputs(struct wacom *wacom)
 {
 	struct input_dev *pen_input_dev, *touch_input_dev, *pad_input_dev;
 	struct wacom_wac *wacom_wac = &(wacom->wacom_wac);
@@ -2104,10 +2107,6 @@
 		input_free_device(pen_input_dev);
 		wacom_wac->pen_input = NULL;
 		pen_input_dev = NULL;
-	} else {
-		error = input_register_device(pen_input_dev);
-		if (error)
-			goto fail;
 	}
 
 	error = wacom_setup_touch_input_capabilities(touch_input_dev, wacom_wac);
@@ -2116,19 +2115,42 @@
 		input_free_device(touch_input_dev);
 		wacom_wac->touch_input = NULL;
 		touch_input_dev = NULL;
-	} else {
-		error = input_register_device(touch_input_dev);
-		if (error)
-			goto fail;
 	}
 
 	error = wacom_setup_pad_input_capabilities(pad_input_dev, wacom_wac);
 	if (error) {
-		/* no pad in use on this interface */
+		/* no pad events using this interface */
 		input_free_device(pad_input_dev);
 		wacom_wac->pad_input = NULL;
 		pad_input_dev = NULL;
-	} else {
+	}
+
+	return 0;
+}
+
+static int wacom_register_inputs(struct wacom *wacom)
+{
+	struct input_dev *pen_input_dev, *touch_input_dev, *pad_input_dev;
+	struct wacom_wac *wacom_wac = &(wacom->wacom_wac);
+	int error = 0;
+
+	pen_input_dev = wacom_wac->pen_input;
+	touch_input_dev = wacom_wac->touch_input;
+	pad_input_dev = wacom_wac->pad_input;
+
+	if (pen_input_dev) {
+		error = input_register_device(pen_input_dev);
+		if (error)
+			goto fail;
+	}
+
+	if (touch_input_dev) {
+		error = input_register_device(touch_input_dev);
+		if (error)
+			goto fail;
+	}
+
+	if (pad_input_dev) {
 		error = input_register_device(pad_input_dev);
 		if (error)
 			goto fail;
@@ -2217,10 +2239,11 @@
 	if ((features->type == HID_GENERIC) && !strcmp("Wacom HID", features->name)) {
 		char *product_name = wacom->hdev->name;
 
-		if (hid_is_using_ll_driver(wacom->hdev, &usb_hid_driver)) {
+		if (hid_is_usb(wacom->hdev)) {
 			struct usb_interface *intf = to_usb_interface(wacom->hdev->dev.parent);
 			struct usb_device *dev = interface_to_usbdev(intf);
-			product_name = dev->product;
+			if (dev->product != NULL)
+				product_name = dev->product;
 		}
 
 		if (wacom->hdev->bus == BUS_I2C) {
@@ -2384,6 +2407,20 @@
 			goto fail;
 	}
 
+	error = wacom_setup_inputs(wacom);
+	if (error)
+		goto fail;
+
+	if (features->type == HID_GENERIC)
+		connect_mask |= HID_CONNECT_DRIVER;
+
+	/* Regular HID work starts now */
+	error = hid_hw_start(hdev, connect_mask);
+	if (error) {
+		hid_err(hdev, "hw start failed\n");
+		goto fail;
+	}
+
 	error = wacom_register_inputs(wacom);
 	if (error)
 		goto fail;
@@ -2398,16 +2435,6 @@
 			goto fail;
 	}
 
-	if (features->type == HID_GENERIC)
-		connect_mask |= HID_CONNECT_DRIVER;
-
-	/* Regular HID work starts now */
-	error = hid_hw_start(hdev, connect_mask);
-	if (error) {
-		hid_err(hdev, "hw start failed\n");
-		goto fail;
-	}
-
 	if (!wireless) {
 		/* Note that if query fails it is not a hard failure */
 		wacom_query_tablet_data(wacom);
@@ -2422,8 +2449,13 @@
 		goto fail_quirks;
 	}
 
-	if (features->device_type & WACOM_DEVICETYPE_WL_MONITOR)
+	if (features->device_type & WACOM_DEVICETYPE_WL_MONITOR) {
 		error = hid_hw_open(hdev);
+		if (error) {
+			hid_err(hdev, "hw open failed\n");
+			goto fail_quirks;
+		}
+	}
 
 	wacom_set_shared_values(wacom_wac);
 	devres_close_group(&hdev->dev, wacom);
@@ -2454,6 +2486,9 @@
 
 	wacom_destroy_battery(wacom);
 
+	if (!usbdev)
+		return;
+
 	/* Stylus interface */
 	hdev1 = usb_get_intfdata(usbdev->config->interface[1]);
 	wacom1 = hid_get_drvdata(hdev1);
@@ -2524,6 +2559,18 @@
 	return;
 }
 
+static void wacom_remote_destroy_battery(struct wacom *wacom, int index)
+{
+	struct wacom_remote *remote = wacom->remote;
+
+	if (remote->remotes[index].battery.battery) {
+		devres_release_group(&wacom->hdev->dev,
+				     &remote->remotes[index].battery.bat_desc);
+		remote->remotes[index].battery.battery = NULL;
+		remote->remotes[index].active_time = 0;
+	}
+}
+
 static void wacom_remote_destroy_one(struct wacom *wacom, unsigned int index)
 {
 	struct wacom_remote *remote = wacom->remote;
@@ -2538,9 +2585,7 @@
 			remote->remotes[i].registered = false;
 			spin_unlock_irqrestore(&remote->remote_lock, flags);
 
-			if (remote->remotes[i].battery.battery)
-				devres_release_group(&wacom->hdev->dev,
-						     &remote->remotes[i].battery.bat_desc);
+			wacom_remote_destroy_battery(wacom, i);
 
 			if (remote->remotes[i].group.name)
 				devres_release_group(&wacom->hdev->dev,
@@ -2548,7 +2593,6 @@
 
 			remote->remotes[i].serial = 0;
 			remote->remotes[i].group.name = NULL;
-			remote->remotes[i].battery.battery = NULL;
 			wacom->led.groups[i].select = WACOM_STATUS_UNKNOWN;
 		}
 	}
@@ -2633,6 +2677,9 @@
 	if (remote->remotes[index].battery.battery)
 		return 0;
 
+	if (!remote->remotes[index].active_time)
+		return 0;
+
 	if (wacom->led.groups[index].select == WACOM_STATUS_UNKNOWN)
 		return 0;
 
@@ -2648,6 +2695,7 @@
 {
 	struct wacom *wacom = container_of(work, struct wacom, remote_work);
 	struct wacom_remote *remote = wacom->remote;
+	ktime_t kt = ktime_get();
 	struct wacom_remote_data data;
 	unsigned long flags;
 	unsigned int count;
@@ -2674,6 +2722,10 @@
 		serial = data.remote[i].serial;
 		if (data.remote[i].connected) {
 
+			if (kt - remote->remotes[i].active_time > WACOM_REMOTE_BATTERY_TIMEOUT
+			    && remote->remotes[i].active_time != 0)
+				wacom_remote_destroy_battery(wacom, i);
+
 			if (remote->remotes[i].serial == serial) {
 				wacom_remote_attach_battery(wacom, i);
 				continue;
@@ -2733,8 +2785,6 @@
 static int wacom_probe(struct hid_device *hdev,
 		const struct hid_device_id *id)
 {
-	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
-	struct usb_device *dev = interface_to_usbdev(intf);
 	struct wacom *wacom;
 	struct wacom_wac *wacom_wac;
 	struct wacom_features *features;
@@ -2769,14 +2819,21 @@
 	wacom_wac->hid_data.inputmode = -1;
 	wacom_wac->mode_report = -1;
 
-	wacom->usbdev = dev;
-	wacom->intf = intf;
+	if (hid_is_usb(hdev)) {
+		struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
+		struct usb_device *dev = interface_to_usbdev(intf);
+
+		wacom->usbdev = dev;
+		wacom->intf = intf;
+	}
+
 	mutex_init(&wacom->lock);
 	INIT_DELAYED_WORK(&wacom->init_work, wacom_init_work);
 	INIT_WORK(&wacom->wireless_work, wacom_wireless_work);
 	INIT_WORK(&wacom->battery_work, wacom_battery_work);
 	INIT_WORK(&wacom->remote_work, wacom_remote_work);
 	INIT_WORK(&wacom->mode_change_work, wacom_mode_change_work);
+	timer_setup(&wacom->idleprox_timer, &wacom_idleprox_timeout, TIMER_DEFERRABLE);
 
 	/* ask for the report descriptor to be loaded by HID */
 	error = hid_parse(hdev);
@@ -2785,6 +2842,11 @@
 		return error;
 	}
 
+	if (features->type == BOOTLOADER) {
+		hid_warn(hdev, "Using device in hidraw-only mode");
+		return hid_hw_start(hdev, HID_CONNECT_HIDRAW);
+	}
+
 	error = wacom_parse_and_register(wacom, false);
 	if (error)
 		return error;
@@ -2817,6 +2879,7 @@
 	cancel_work_sync(&wacom->battery_work);
 	cancel_work_sync(&wacom->remote_work);
 	cancel_work_sync(&wacom->mode_change_work);
+	del_timer_sync(&wacom->idleprox_timer);
 	if (hdev->bus == BUS_BLUETOOTH)
 		device_remove_file(&hdev->dev, &dev_attr_speed);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/wacom_wac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/wacom_wac.c
@@ -11,6 +11,7 @@
 #include "wacom_wac.h"
 #include "wacom.h"
 #include <linux/input/mt.h>
+#include <linux/jiffies.h>
 
 /* resolution for penabled devices */
 #define WACOM_PL_RES		20
@@ -41,6 +42,43 @@
 
 static void wacom_update_led(struct wacom *wacom, int button_count, int mask,
 			     int group);
+
+static void wacom_force_proxout(struct wacom_wac *wacom_wac)
+{
+	struct input_dev *input = wacom_wac->pen_input;
+
+	wacom_wac->shared->stylus_in_proximity = 0;
+
+	input_report_key(input, BTN_TOUCH, 0);
+	input_report_key(input, BTN_STYLUS, 0);
+	input_report_key(input, BTN_STYLUS2, 0);
+	input_report_key(input, BTN_STYLUS3, 0);
+	input_report_key(input, wacom_wac->tool[0], 0);
+	if (wacom_wac->serial[0]) {
+		input_report_abs(input, ABS_MISC, 0);
+	}
+	input_report_abs(input, ABS_PRESSURE, 0);
+
+	wacom_wac->tool[0] = 0;
+	wacom_wac->id[0] = 0;
+	wacom_wac->serial[0] = 0;
+
+	input_sync(input);
+}
+
+void wacom_idleprox_timeout(struct timer_list *list)
+{
+	struct wacom *wacom = from_timer(wacom, list, idleprox_timer);
+	struct wacom_wac *wacom_wac = &wacom->wacom_wac;
+
+	if (!wacom_wac->hid_data.sense_state) {
+		return;
+	}
+
+	hid_warn(wacom->hdev, "%s: tool appears to be hung in-prox. forcing it out.\n", __func__);
+	wacom_force_proxout(wacom_wac);
+}
+
 /*
  * Percent of battery capacity for Graphire.
  * 8th value means AC online and show 100% capacity.
@@ -638,9 +676,26 @@
 	return (tool_id & ~0xFFF) << 4 | (tool_id & 0xFFF);
 }
 
+static bool wacom_is_art_pen(int tool_id)
+{
+	bool is_art_pen = false;
+
+	switch (tool_id) {
+	case 0x885:	/* Intuos3 Marker Pen */
+	case 0x804:	/* Intuos4/5 13HD/24HD Marker Pen */
+	case 0x10804:	/* Intuos4/5 13HD/24HD Art Pen */
+		is_art_pen = true;
+		break;
+	}
+	return is_art_pen;
+}
+
 static int wacom_intuos_get_tool_type(int tool_id)
 {
-	int tool_type;
+	int tool_type = BTN_TOOL_PEN;
+
+	if (wacom_is_art_pen(tool_id))
+		return tool_type;
 
 	switch (tool_id) {
 	case 0x812: /* Inking pen */
@@ -655,17 +710,16 @@
 	case 0x852:
 	case 0x823: /* Intuos3 Grip Pen */
 	case 0x813: /* Intuos3 Classic Pen */
-	case 0x885: /* Intuos3 Marker Pen */
 	case 0x802: /* Intuos4/5 13HD/24HD General Pen */
-	case 0x804: /* Intuos4/5 13HD/24HD Marker Pen */
 	case 0x8e2: /* IntuosHT2 pen */
 	case 0x022:
-	case 0x10804: /* Intuos4/5 13HD/24HD Art Pen */
+	case 0x200: /* Pro Pen 3 */
 	case 0x10842: /* MobileStudio Pro Pro Pen slim */
 	case 0x14802: /* Intuos4/5 13HD/24HD Classic Pen */
 	case 0x16802: /* Cintiq 13HD Pro Pen */
 	case 0x18802: /* DTH2242 Pen */
 	case 0x10802: /* Intuos4/5 13HD/24HD General Pen */
+	case 0x8842: /* Intuos Pro and Cintiq Pro 3D Pen */
 		tool_type = BTN_TOOL_PEN;
 		break;
 
@@ -718,10 +772,6 @@
 	case 0x10902: /* Intuos4/5 13HD/24HD Airbrush */
 		tool_type = BTN_TOOL_AIRBRUSH;
 		break;
-
-	default: /* Unknown tool */
-		tool_type = BTN_TOOL_PEN;
-		break;
 	}
 	return tool_type;
 }
@@ -780,7 +830,7 @@
 	/* Enter report */
 	if ((data[1] & 0xfc) == 0xc0) {
 		/* serial number of the tool */
-		wacom->serial[idx] = ((data[3] & 0x0f) << 28) +
+		wacom->serial[idx] = ((__u64)(data[3] & 0x0f) << 28) +
 			(data[4] << 20) + (data[5] << 12) +
 			(data[6] << 4) + (data[7] >> 4);
 
@@ -1083,6 +1133,7 @@
 	if (index < 0 || !remote->remotes[index].registered)
 		goto out;
 
+	remote->remotes[i].active_time = ktime_get();
 	input = remote->remotes[index].input;
 
 	input_report_key(input, BTN_0, (data[9] & 0x01));
@@ -1262,6 +1313,9 @@
 
 	struct input_dev *pen_input = wacom->pen_input;
 	unsigned char *data = wacom->data;
+	int number_of_valid_frames = 0;
+	ktime_t time_interval = 15000000;
+	ktime_t time_packet_received = ktime_get();
 	int i;
 
 	if (wacom->features.type == INTUOSP2_BT ||
@@ -1282,12 +1336,30 @@
 		wacom->id[0] |= (wacom->serial[0] >> 32) & 0xFFFFF;
 	}
 
+	/* number of valid frames */
 	for (i = 0; i < pen_frames; i++) {
 		unsigned char *frame = &data[i*pen_frame_len + 1];
 		bool valid = frame[0] & 0x80;
+
+		if (valid)
+			number_of_valid_frames++;
+	}
+
+	if (number_of_valid_frames) {
+		if (wacom->hid_data.time_delayed)
+			time_interval = ktime_get() - wacom->hid_data.time_delayed;
+		time_interval = div_u64(time_interval, number_of_valid_frames);
+		wacom->hid_data.time_delayed = time_packet_received;
+	}
+
+	for (i = 0; i < number_of_valid_frames; i++) {
+		unsigned char *frame = &data[i*pen_frame_len + 1];
+		bool valid = frame[0] & 0x80;
 		bool prox = frame[0] & 0x40;
 		bool range = frame[0] & 0x20;
 		bool invert = frame[0] & 0x10;
+		int frames_number_reversed = number_of_valid_frames - i - 1;
+		ktime_t event_timestamp = time_packet_received - frames_number_reversed * time_interval;
 
 		if (!valid)
 			continue;
@@ -1300,6 +1372,7 @@
 			wacom->tool[0] = 0;
 			wacom->id[0] = 0;
 			wacom->serial[0] = 0;
+			wacom->hid_data.time_delayed = 0;
 			return;
 		}
 
@@ -1328,14 +1401,15 @@
 					rotation -= 1800;
 
 				input_report_abs(pen_input, ABS_TILT_X,
-						 (char)frame[7]);
+						 (signed char)frame[7]);
 				input_report_abs(pen_input, ABS_TILT_Y,
-						 (char)frame[8]);
+						 (signed char)frame[8]);
 				input_report_abs(pen_input, ABS_Z, rotation);
 				input_report_abs(pen_input, ABS_WHEEL,
 						 get_unaligned_le16(&frame[11]));
 			}
 		}
+
 		if (wacom->tool[0]) {
 			input_report_abs(pen_input, ABS_PRESSURE, get_unaligned_le16(&frame[5]));
 			if (wacom->features.type == INTUOSP2_BT ||
@@ -1359,6 +1433,9 @@
 
 		wacom->shared->stylus_in_proximity = prox;
 
+		/* add timestamp to unpack the frames */
+		input_set_timestamp(pen_input, event_timestamp);
+
 		input_sync(pen_input);
 	}
 }
@@ -1847,11 +1924,14 @@
 	int fmax = field->logical_maximum;
 	unsigned int equivalent_usage = wacom_equivalent_usage(usage->hid);
 	int resolution_code = code;
+	int resolution;
 
 	if (equivalent_usage == HID_DG_TWIST) {
 		resolution_code = ABS_RZ;
 	}
 
+	resolution = hidinput_calc_abs_res(field, resolution_code);
+
 	if (equivalent_usage == HID_GD_X) {
 		fmin += features->offset_left;
 		fmax -= features->offset_right;
@@ -1867,8 +1947,15 @@
 	switch (type) {
 	case EV_ABS:
 		input_set_abs_params(input, code, fmin, fmax, fuzz, 0);
-		input_abs_set_res(input, code,
-				  hidinput_calc_abs_res(field, resolution_code));
+
+		/* older tablet may miss physical usage */
+		if ((code == ABS_X || code == ABS_Y) && !resolution) {
+			resolution = WACOM_INTUOS_RES;
+			hid_warn(input,
+				 "Wacom usage (%d) missing resolution \n",
+				 code);
+		}
+		input_abs_set_res(input, code, resolution);
 		break;
 	case EV_KEY:
 	case EV_MSC:
@@ -1881,18 +1968,7 @@
 static void wacom_wac_battery_usage_mapping(struct hid_device *hdev,
 		struct hid_field *field, struct hid_usage *usage)
 {
-	struct wacom *wacom = hid_get_drvdata(hdev);
-	struct wacom_wac *wacom_wac = &wacom->wacom_wac;
-	struct wacom_features *features = &wacom_wac->features;
-	unsigned equivalent_usage = wacom_equivalent_usage(usage->hid);
-
-	switch (equivalent_usage) {
-	case HID_DG_BATTERYSTRENGTH:
-	case WACOM_HID_WD_BATTERY_LEVEL:
-	case WACOM_HID_WD_BATTERY_CHARGING:
-		features->quirks |= WACOM_QUIRK_BATTERY;
-		break;
-	}
+	return;
 }
 
 static void wacom_wac_battery_event(struct hid_device *hdev, struct hid_field *field,
@@ -1913,18 +1989,21 @@
 			wacom_wac->hid_data.bat_connected = 1;
 			wacom_wac->hid_data.bat_status = WACOM_POWER_SUPPLY_STATUS_AUTO;
 		}
+		wacom_wac->features.quirks |= WACOM_QUIRK_BATTERY;
 		break;
 	case WACOM_HID_WD_BATTERY_LEVEL:
 		value = value * 100 / (field->logical_maximum - field->logical_minimum);
 		wacom_wac->hid_data.battery_capacity = value;
 		wacom_wac->hid_data.bat_connected = 1;
 		wacom_wac->hid_data.bat_status = WACOM_POWER_SUPPLY_STATUS_AUTO;
+		wacom_wac->features.quirks |= WACOM_QUIRK_BATTERY;
 		break;
 	case WACOM_HID_WD_BATTERY_CHARGING:
 		wacom_wac->hid_data.bat_charging = value;
 		wacom_wac->hid_data.ps_connected = value;
 		wacom_wac->hid_data.bat_connected = 1;
 		wacom_wac->hid_data.bat_status = WACOM_POWER_SUPPLY_STATUS_AUTO;
+		wacom_wac->features.quirks |= WACOM_QUIRK_BATTERY;
 		break;
 	}
 }
@@ -1940,18 +2019,15 @@
 {
 	struct wacom *wacom = hid_get_drvdata(hdev);
 	struct wacom_wac *wacom_wac = &wacom->wacom_wac;
-	struct wacom_features *features = &wacom_wac->features;
 
-	if (features->quirks & WACOM_QUIRK_BATTERY) {
-		int status = wacom_wac->hid_data.bat_status;
-		int capacity = wacom_wac->hid_data.battery_capacity;
-		bool charging = wacom_wac->hid_data.bat_charging;
-		bool connected = wacom_wac->hid_data.bat_connected;
-		bool powered = wacom_wac->hid_data.ps_connected;
+	int status = wacom_wac->hid_data.bat_status;
+	int capacity = wacom_wac->hid_data.battery_capacity;
+	bool charging = wacom_wac->hid_data.bat_charging;
+	bool connected = wacom_wac->hid_data.bat_connected;
+	bool powered = wacom_wac->hid_data.ps_connected;
 
-		wacom_notify_battery(wacom_wac, status, capacity, charging,
-				     connected, powered);
-	}
+	wacom_notify_battery(wacom_wac, status, capacity, charging,
+			     connected, powered);
 }
 
 static void wacom_wac_pad_usage_mapping(struct hid_device *hdev,
@@ -2007,7 +2083,6 @@
 		wacom_wac->has_mute_touch_switch = true;
 		usage->type = EV_SW;
 		usage->code = SW_MUTE_DEVICE;
-		features->device_type |= WACOM_DEVICETYPE_PAD;
 		break;
 	case WACOM_HID_WD_TOUCHSTRIP:
 		wacom_map_usage(input, usage, field, EV_ABS, ABS_RX, 0);
@@ -2087,6 +2162,30 @@
 			wacom_wac->hid_data.inrange_state |= value;
 	}
 
+	/* Process touch switch state first since it is reported through touch interface,
+	 * which is indepentent of pad interface. In the case when there are no other pad
+	 * events, the pad interface will not even be created.
+	 */
+	if ((equivalent_usage == WACOM_HID_WD_MUTE_DEVICE) ||
+	   (equivalent_usage == WACOM_HID_WD_TOUCHONOFF)) {
+		if (wacom_wac->shared->touch_input) {
+			bool *is_touch_on = &wacom_wac->shared->is_touch_on;
+
+			if (equivalent_usage == WACOM_HID_WD_MUTE_DEVICE && value)
+				*is_touch_on = !(*is_touch_on);
+			else if (equivalent_usage == WACOM_HID_WD_TOUCHONOFF)
+				*is_touch_on = value;
+
+			input_report_switch(wacom_wac->shared->touch_input,
+					    SW_MUTE_DEVICE, !(*is_touch_on));
+			input_sync(wacom_wac->shared->touch_input);
+		}
+		return;
+	}
+
+	if (!input)
+		return;
+
 	switch (equivalent_usage) {
 	case WACOM_HID_WD_TOUCHRING:
 		/*
@@ -2122,22 +2221,6 @@
 			input_event(input, usage->type, usage->code, 0);
 		break;
 
-	case WACOM_HID_WD_MUTE_DEVICE:
-	case WACOM_HID_WD_TOUCHONOFF:
-		if (wacom_wac->shared->touch_input) {
-			bool *is_touch_on = &wacom_wac->shared->is_touch_on;
-
-			if (equivalent_usage == WACOM_HID_WD_MUTE_DEVICE && value)
-				*is_touch_on = !(*is_touch_on);
-			else if (equivalent_usage == WACOM_HID_WD_TOUCHONOFF)
-				*is_touch_on = value;
-
-			input_report_switch(wacom_wac->shared->touch_input,
-					    SW_MUTE_DEVICE, !(*is_touch_on));
-			input_sync(wacom_wac->shared->touch_input);
-		}
-		break;
-
 	case WACOM_HID_WD_MODE_CHANGE:
 		if (wacom_wac->is_direct_mode != value) {
 			wacom_wac->is_direct_mode = value;
@@ -2299,6 +2382,7 @@
 		value = field->logical_maximum - value;
 		break;
 	case HID_DG_INRANGE:
+		mod_timer(&wacom->idleprox_timer, jiffies + msecs_to_jiffies(100));
 		wacom_wac->hid_data.inrange_state = value;
 		if (!(features->quirks & WACOM_QUIRK_SENSE))
 			wacom_wac->hid_data.sense_state = value;
@@ -2323,6 +2407,9 @@
 		}
 		return;
 	case HID_DG_TWIST:
+		/* don't modify the value if the pen doesn't support the feature */
+		if (!wacom_is_art_pen(wacom_wac->id[0])) return;
+
 		/*
 		 * Userspace expects pen twist to have its zero point when
 		 * the buttons/finger is on the tablet's left. HID values
@@ -2465,7 +2552,14 @@
 				wacom_wac->hid_data.tipswitch);
 		input_report_key(input, wacom_wac->tool[0], sense);
 		if (wacom_wac->serial[0]) {
-			input_event(input, EV_MSC, MSC_SERIAL, wacom_wac->serial[0]);
+			/*
+			 * xf86-input-wacom does not accept a serial number
+			 * of '0'. Report the low 32 bits if possible, but
+			 * if they are zero, report the upper ones instead.
+			 */
+			__u32 serial_lo = wacom_wac->serial[0] & 0xFFFFFFFFu;
+			__u32 serial_hi = wacom_wac->serial[0] >> 32;
+			input_event(input, EV_MSC, MSC_SERIAL, (int)(serial_lo ? serial_lo : serial_hi));
 			input_report_abs(input, ABS_MISC, sense ? id : 0);
 		}
 
@@ -2537,8 +2631,8 @@
 {
 	struct hid_data *hid_data = &wacom_wac->hid_data;
 	bool mt = wacom_wac->features.touch_max > 1;
-	bool prox = hid_data->tipswitch &&
-		    report_touch_events(wacom_wac);
+	bool touch_down = hid_data->tipswitch && hid_data->confidence;
+	bool prox = touch_down && report_touch_events(wacom_wac);
 
 	if (touch_is_muted(wacom_wac)) {
 		if (!wacom_wac->shared->touch_down)
@@ -2603,6 +2697,9 @@
 		return;
 
 	switch (equivalent_usage) {
+	case HID_DG_CONFIDENCE:
+		wacom_wac->hid_data.confidence = value;
+		break;
 	case HID_GD_X:
 		wacom_wac->hid_data.x = value;
 		break;
@@ -2653,6 +2750,12 @@
 
 	wacom_wac->is_invalid_bt_frame = false;
 
+	hid_data->confidence = true;
+
+	hid_data->cc_report = 0;
+	hid_data->cc_index = -1;
+	hid_data->cc_value_index = -1;
+
 	for (i = 0; i < report->maxfield; i++) {
 		struct hid_field *field = report->field[i];
 		int j;
@@ -2686,11 +2789,14 @@
 	    hid_data->cc_index >= 0) {
 		struct hid_field *field = report->field[hid_data->cc_index];
 		int value = field->value[hid_data->cc_value_index];
-		if (value)
+		if (value) {
 			hid_data->num_expected = value;
+			hid_data->num_received = 0;
+		}
 	}
 	else {
 		hid_data->num_expected = wacom_wac->features.touch_max;
+		hid_data->num_received = 0;
 	}
 }
 
@@ -2718,6 +2824,7 @@
 
 	input_sync(input);
 	wacom_wac->hid_data.num_received = 0;
+	wacom_wac->hid_data.num_expected = 0;
 
 	/* keep touch state for pen event */
 	wacom_wac->shared->touch_down = wacom_wac_finger_count_touches(wacom_wac);
@@ -2758,7 +2865,7 @@
 	/* usage tests must precede field tests */
 	if (WACOM_BATTERY_USAGE(usage))
 		wacom_wac_battery_event(hdev, field, usage, value);
-	else if (WACOM_PAD_FIELD(field) && wacom->wacom_wac.pad_input)
+	else if (WACOM_PAD_FIELD(field))
 		wacom_wac_pad_event(hdev, field, usage, value);
 	else if (WACOM_PEN_FIELD(field) && wacom->wacom_wac.pen_input)
 		wacom_wac_pen_event(hdev, field, usage, value);
@@ -4752,10 +4859,17 @@
 static const struct wacom_features wacom_features_0x3c8 =
 	{ "Wacom Intuos BT M", 21600, 13500, 4095, 63,
 	  INTUOSHT3_BT, WACOM_INTUOS_RES, WACOM_INTUOS_RES, 4 };
+static const struct wacom_features wacom_features_0x3dd =
+	{ "Wacom Intuos Pro S", 31920, 19950, 8191, 63,
+	  INTUOSP2S_BT, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES, 7,
+	  .touch_max = 10 };
 
 static const struct wacom_features wacom_features_HID_ANY_ID =
 	{ "Wacom HID", .type = HID_GENERIC, .oVid = HID_ANY_ID, .oPid = HID_ANY_ID };
 
+static const struct wacom_features wacom_features_0x94 =
+	{ "Wacom Bootloader", .type = BOOTLOADER };
+
 #define USB_DEVICE_WACOM(prod)						\
 	HID_DEVICE(BUS_USB, HID_GROUP_WACOM, USB_VENDOR_ID_WACOM, prod),\
 	.driver_data = (kernel_ulong_t)&wacom_features_##prod
@@ -4768,6 +4882,10 @@
 	HID_DEVICE(BUS_I2C, HID_GROUP_WACOM, USB_VENDOR_ID_WACOM, prod),\
 	.driver_data = (kernel_ulong_t)&wacom_features_##prod
 
+#define PCI_DEVICE_WACOM(prod)						\
+	HID_DEVICE(BUS_PCI, HID_GROUP_WACOM, USB_VENDOR_ID_WACOM, prod),\
+	.driver_data = (kernel_ulong_t)&wacom_features_##prod
+
 #define USB_DEVICE_LENOVO(prod)					\
 	HID_USB_DEVICE(USB_VENDOR_ID_LENOVO, prod),			\
 	.driver_data = (kernel_ulong_t)&wacom_features_##prod
@@ -4829,6 +4947,7 @@
 	{ USB_DEVICE_WACOM(0x84) },
 	{ USB_DEVICE_WACOM(0x90) },
 	{ USB_DEVICE_WACOM(0x93) },
+	{ USB_DEVICE_WACOM(0x94) },
 	{ USB_DEVICE_WACOM(0x97) },
 	{ USB_DEVICE_WACOM(0x9A) },
 	{ USB_DEVICE_WACOM(0x9F) },
@@ -4927,6 +5046,7 @@
 	{ BT_DEVICE_WACOM(0x393) },
 	{ BT_DEVICE_WACOM(0x3c6) },
 	{ BT_DEVICE_WACOM(0x3c8) },
+	{ BT_DEVICE_WACOM(0x3dd) },
 	{ USB_DEVICE_WACOM(0x4001) },
 	{ USB_DEVICE_WACOM(0x4004) },
 	{ USB_DEVICE_WACOM(0x5000) },
@@ -4935,6 +5055,7 @@
 
 	{ USB_DEVICE_WACOM(HID_ANY_ID) },
 	{ I2C_DEVICE_WACOM(HID_ANY_ID) },
+	{ PCI_DEVICE_WACOM(HID_ANY_ID) },
 	{ BT_DEVICE_WACOM(HID_ANY_ID) },
 	{ }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hid/wacom_wac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hid/wacom_wac.h
@@ -15,6 +15,7 @@
 #define WACOM_NAME_MAX		64
 #define WACOM_MAX_REMOTES	5
 #define WACOM_STATUS_UNKNOWN	255
+#define WACOM_REMOTE_BATTERY_TIMEOUT	21000000000ll
 
 /* packet length for individual models */
 #define WACOM_PKGLEN_BBFUN	 9
@@ -242,6 +243,7 @@
 	MTTPC,
 	MTTPC_B,
 	HID_GENERIC,
+	BOOTLOADER,
 	MAX_TYPE
 };
 
@@ -301,6 +303,7 @@
 	bool barrelswitch;
 	bool barrelswitch2;
 	bool serialhi;
+	bool confidence;
 	int x;
 	int y;
 	int pressure;
@@ -319,6 +322,7 @@
 	int bat_connected;
 	int ps_connected;
 	bool pad_input_event_flag;
+	ktime_t time_delayed;
 };
 
 struct wacom_remote_data {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hsi/controllers/omap_ssi_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hsi/controllers/omap_ssi_core.c
@@ -502,8 +502,10 @@
 	platform_set_drvdata(pd, ssi);
 
 	err = ssi_add_controller(ssi, pd);
-	if (err < 0)
+	if (err < 0) {
+		hsi_put_controller(ssi);
 		goto out1;
+	}
 
 	pm_runtime_enable(&pd->dev);
 
@@ -524,6 +526,7 @@
 		if (!childpdev) {
 			err = -ENODEV;
 			dev_err(&pd->dev, "failed to create ssi controller port\n");
+			of_node_put(child);
 			goto out3;
 		}
 	}
@@ -535,9 +538,9 @@
 	device_for_each_child(&pd->dev, NULL, ssi_remove_ports);
 out2:
 	ssi_remove_controller(ssi);
+	pm_runtime_disable(&pd->dev);
 out1:
 	platform_set_drvdata(pd, NULL);
-	pm_runtime_disable(&pd->dev);
 
 	return err;
 }
@@ -628,7 +631,13 @@
 	if (ret)
 		return ret;
 
-	return platform_driver_register(&ssi_port_pdriver);
+	ret = platform_driver_register(&ssi_port_pdriver);
+	if (ret) {
+		platform_driver_unregister(&ssi_pdriver);
+		return ret;
+	}
+
+	return 0;
 }
 module_init(ssi_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hsi/controllers/omap_ssi_port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hsi/controllers/omap_ssi_port.c
@@ -230,10 +230,10 @@
 	if (msg->ttype == HSI_MSG_READ) {
 		err = dma_map_sg(&ssi->device, msg->sgt.sgl, msg->sgt.nents,
 							DMA_FROM_DEVICE);
-		if (err < 0) {
+		if (!err) {
 			dev_dbg(&ssi->device, "DMA map SG failed !\n");
 			pm_runtime_put_autosuspend(omap_port->pdev);
-			return err;
+			return -EIO;
 		}
 		csdp = SSI_DST_BURST_4x32_BIT | SSI_DST_MEMORY_PORT |
 			SSI_SRC_SINGLE_ACCESS0 | SSI_SRC_PERIPHERAL_PORT |
@@ -247,10 +247,10 @@
 	} else {
 		err = dma_map_sg(&ssi->device, msg->sgt.sgl, msg->sgt.nents,
 							DMA_TO_DEVICE);
-		if (err < 0) {
+		if (!err) {
 			dev_dbg(&ssi->device, "DMA map SG failed !\n");
 			pm_runtime_put_autosuspend(omap_port->pdev);
-			return err;
+			return -EIO;
 		}
 		csdp = SSI_SRC_BURST_4x32_BIT | SSI_SRC_MEMORY_PORT |
 			SSI_DST_SINGLE_ACCESS0 | SSI_DST_PERIPHERAL_PORT |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hsi/hsi_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hsi/hsi_core.c
@@ -102,6 +102,7 @@
 	if (device_register(&cl->device) < 0) {
 		pr_err("hsi: failed to register client: %s\n", info->name);
 		put_device(&cl->device);
+		goto err;
 	}
 
 	return cl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/Kconfig
@@ -18,6 +18,7 @@
 config HYPERV_UTILS
 	tristate "Microsoft Hyper-V Utilities driver"
 	depends on HYPERV && CONNECTOR && NLS
+	depends on PTP_1588_CLOCK_OPTIONAL
 	help
 	  Select this option to enable the Hyper-V Utilities.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/channel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/channel.c
@@ -1221,7 +1221,9 @@
 
 	/*
 	 * Cannot return an ID of 0, which is reserved for an unsolicited
-	 * message from Hyper-V.
+	 * message from Hyper-V; Hyper-V does not acknowledge (respond to)
+	 * VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED requests with ID of
+	 * 0 sent by the guest.
 	 */
 	return current_id + 1;
 }
@@ -1246,7 +1248,7 @@
 
 	/* Hyper-V can send an unsolicited message with ID of 0 */
 	if (!trans_id)
-		return trans_id;
+		return VMBUS_RQST_ERROR;
 
 	spin_lock_irqsave(&rqstor->req_lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/channel_mgmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/channel_mgmt.c
@@ -380,7 +380,7 @@
 	 * execute:
 	 *
 	 *  (a) In the "normal (i.e., not resuming from hibernation)" path,
-	 *      the full barrier in smp_store_mb() guarantees that the store
+	 *      the full barrier in virt_store_mb() guarantees that the store
 	 *      is propagated to all CPUs before the add_channel_work work
 	 *      is queued.  In turn, add_channel_work is queued before the
 	 *      channel's ring buffer is allocated/initialized and the
@@ -392,14 +392,14 @@
 	 *      recv_int_page before retrieving the channel pointer from the
 	 *      array of channels.
 	 *
-	 *  (b) In the "resuming from hibernation" path, the smp_store_mb()
+	 *  (b) In the "resuming from hibernation" path, the virt_store_mb()
 	 *      guarantees that the store is propagated to all CPUs before
 	 *      the VMBus connection is marked as ready for the resume event
 	 *      (cf. check_ready_for_resume_event()).  The interrupt handler
 	 *      of the VMBus driver and vmbus_chan_sched() can not run before
 	 *      vmbus_bus_resume() has completed execution (cf. resume_noirq).
 	 */
-	smp_store_mb(
+	virt_store_mb(
 		vmbus_connection.channels[channel->offermsg.child_relid],
 		channel);
 }
@@ -531,13 +531,17 @@
 	 * Add the new device to the bus. This will kick off device-driver
 	 * binding which eventually invokes the device driver's AddDevice()
 	 * method.
+	 *
+	 * If vmbus_device_register() fails, the 'device_obj' is freed in
+	 * vmbus_device_release() as called by device_unregister() in the
+	 * error path of vmbus_device_register(). In the outside error
+	 * path, there's no need to free it.
 	 */
 	ret = vmbus_device_register(newchannel->device_obj);
 
 	if (ret != 0) {
 		pr_err("unable to add child device object (relid %d)\n",
 			newchannel->offermsg.child_relid);
-		kfree(newchannel->device_obj);
 		goto err_deq_chan;
 	}
 
@@ -637,6 +641,7 @@
 		 */
 		if (newchannel->offermsg.offer.sub_channel_index == 0) {
 			mutex_unlock(&vmbus_connection.channel_mutex);
+			cpus_read_unlock();
 			/*
 			 * Don't call free_channel(), because newchannel->kobj
 			 * is not initialized yet.
@@ -822,11 +827,22 @@
 		if (completion_done(&vmbus_connection.unload_event))
 			goto completed;
 
-		for_each_online_cpu(cpu) {
+		for_each_present_cpu(cpu) {
 			struct hv_per_cpu_context *hv_cpu
 				= per_cpu_ptr(hv_context.cpu_context, cpu);
 
+			/*
+			 * In a CoCo VM the synic_message_page is not allocated
+			 * in hv_synic_alloc(). Instead it is set/cleared in
+			 * hv_synic_enable_regs() and hv_synic_disable_regs()
+			 * such that it is set only when the CPU is online. If
+			 * not all present CPUs are online, the message page
+			 * might be NULL, so skip such CPUs.
+			 */
 			page_addr = hv_cpu->synic_message_page;
+			if (!page_addr)
+				continue;
+
 			msg = (struct hv_message *)page_addr
 				+ VMBUS_MESSAGE_SINT;
 
@@ -860,11 +876,14 @@
 	 * maybe-pending messages on all CPUs to be able to receive new
 	 * messages after we reconnect.
 	 */
-	for_each_online_cpu(cpu) {
+	for_each_present_cpu(cpu) {
 		struct hv_per_cpu_context *hv_cpu
 			= per_cpu_ptr(hv_context.cpu_context, cpu);
 
 		page_addr = hv_cpu->synic_message_page;
+		if (!page_addr)
+			continue;
+
 		msg = (struct hv_message *)page_addr + VMBUS_MESSAGE_SINT;
 		msg->header.message_type = HVMSG_NONE;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/connection.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/connection.c
@@ -315,6 +315,10 @@
  */
 struct vmbus_channel *relid2channel(u32 relid)
 {
+	if (vmbus_connection.channels == NULL) {
+		pr_warn_once("relid2channel: relid=%d: No channels mapped!\n", relid);
+		return NULL;
+	}
 	if (WARN_ON(relid >= MAX_CHANNEL_RELIDS))
 		return NULL;
 	return READ_ONCE(vmbus_connection.channels[relid]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/hv_balloon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/hv_balloon.c
@@ -17,6 +17,7 @@
 #include <linux/slab.h>
 #include <linux/kthread.h>
 #include <linux/completion.h>
+#include <linux/count_zeros.h>
 #include <linux/memory_hotplug.h>
 #include <linux/memory.h>
 #include <linux/notifier.h>
@@ -480,7 +481,7 @@
 MODULE_PARM_DESC(pressure_report_delay, "Delay in secs in reporting pressure");
 static atomic_t trans_id = ATOMIC_INIT(0);
 
-static int dm_ring_size = 20 * 1024;
+static int dm_ring_size = VMBUS_RING_SIZE(16 * 1024);
 
 /*
  * Driver specific state.
@@ -1130,6 +1131,7 @@
 	struct dm_status status;
 	unsigned long now = jiffies;
 	unsigned long last_post = last_post_time;
+	unsigned long num_pages_avail, num_pages_committed;
 
 	if (pressure_report_delay > 0) {
 		--pressure_report_delay;
@@ -1154,16 +1156,21 @@
 	 * num_pages_onlined) as committed to the host, otherwise it can try
 	 * asking us to balloon them out.
 	 */
-	status.num_avail = si_mem_available();
-	status.num_committed = vm_memory_committed() +
+	num_pages_avail = si_mem_available();
+	num_pages_committed = vm_memory_committed() +
 		dm->num_pages_ballooned +
 		(dm->num_pages_added > dm->num_pages_onlined ?
 		 dm->num_pages_added - dm->num_pages_onlined : 0) +
 		compute_balloon_floor();
 
-	trace_balloon_status(status.num_avail, status.num_committed,
+	trace_balloon_status(num_pages_avail, num_pages_committed,
 			     vm_memory_committed(), dm->num_pages_ballooned,
 			     dm->num_pages_added, dm->num_pages_onlined);
+
+	/* Convert numbers of pages into numbers of HV_HYP_PAGEs. */
+	status.num_avail = num_pages_avail * NR_HV_HYP_PAGES_IN_PAGE;
+	status.num_committed = num_pages_committed * NR_HV_HYP_PAGES_IN_PAGE;
+
 	/*
 	 * If our transaction ID is no longer current, just don't
 	 * send the status. This can happen if we were interrupted
@@ -1563,7 +1570,7 @@
 			break;
 
 		default:
-			pr_warn("Unhandled message: type: %d\n", dm_hdr->type);
+			pr_warn_ratelimited("Unhandled message: type: %d\n", dm_hdr->type);
 
 		}
 	}
@@ -1653,6 +1660,38 @@
 	}
 }
 
+static int ballooning_enabled(void)
+{
+	/*
+	 * Disable ballooning if the page size is not 4k (HV_HYP_PAGE_SIZE),
+	 * since currently it's unclear to us whether an unballoon request can
+	 * make sure all page ranges are guest page size aligned.
+	 */
+	if (PAGE_SIZE != HV_HYP_PAGE_SIZE) {
+		pr_info("Ballooning disabled because page size is not 4096 bytes\n");
+		return 0;
+	}
+
+	return 1;
+}
+
+static int hot_add_enabled(void)
+{
+	/*
+	 * Disable hot add on ARM64, because we currently rely on
+	 * memory_add_physaddr_to_nid() to get a node id of a hot add range,
+	 * however ARM64's memory_add_physaddr_to_nid() always return 0 and
+	 * DM_MEM_HOT_ADD_REQUEST doesn't have the NUMA node information for
+	 * add_memory().
+	 */
+	if (IS_ENABLED(CONFIG_ARM64)) {
+		pr_info("Memory hot add disabled on ARM64\n");
+		return 0;
+	}
+
+	return 1;
+}
+
 static int balloon_connect_vsp(struct hv_device *dev)
 {
 	struct dm_version_request version_req;
@@ -1660,6 +1699,13 @@
 	unsigned long t;
 	int ret;
 
+	/*
+	 * max_pkt_size should be large enough for one vmbus packet header plus
+	 * our receive buffer size. Hyper-V sends messages up to
+	 * HV_HYP_PAGE_SIZE bytes long on balloon channel.
+	 */
+	dev->channel->max_pkt_size = HV_HYP_PAGE_SIZE * 2;
+
 	ret = vmbus_open(dev->channel, dm_ring_size, dm_ring_size, NULL, 0,
 			 balloon_onchannelcallback, dev);
 	if (ret)
@@ -1717,8 +1763,8 @@
 	 * currently still requires the bits to be set, so we have to add code
 	 * to fail the host's hot-add and balloon up/down requests, if any.
 	 */
-	cap_msg.caps.cap_bits.balloon = 1;
-	cap_msg.caps.cap_bits.hot_add = 1;
+	cap_msg.caps.cap_bits.balloon = ballooning_enabled();
+	cap_msg.caps.cap_bits.hot_add = hot_add_enabled();
 
 	/*
 	 * Specify our alignment requirements as it relates
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/hv_kvp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/hv_kvp.c
@@ -767,6 +767,12 @@
 	 */
 	kvp_transaction.state = HVUTIL_DEVICE_INIT;
 
+	return 0;
+}
+
+int
+hv_kvp_init_transport(void)
+{
 	hvt = hvutil_transport_init(kvp_devname, CN_KVP_IDX, CN_KVP_VAL,
 				    kvp_on_msg, kvp_on_reset);
 	if (!hvt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/hv_snapshot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/hv_snapshot.c
@@ -385,6 +385,12 @@
 	 */
 	vss_transaction.state = HVUTIL_DEVICE_INIT;
 
+	return 0;
+}
+
+int
+hv_vss_init_transport(void)
+{
 	hvt = hvutil_transport_init(vss_devname, CN_VSS_IDX, CN_VSS_VAL,
 				    vss_on_msg, vss_on_reset);
 	if (!hvt) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/hv_util.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/hv_util.c
@@ -141,6 +141,7 @@
 static struct hv_util_service util_kvp = {
 	.util_cb = hv_kvp_onchannelcallback,
 	.util_init = hv_kvp_init,
+	.util_init_transport = hv_kvp_init_transport,
 	.util_pre_suspend = hv_kvp_pre_suspend,
 	.util_pre_resume = hv_kvp_pre_resume,
 	.util_deinit = hv_kvp_deinit,
@@ -149,6 +150,7 @@
 static struct hv_util_service util_vss = {
 	.util_cb = hv_vss_onchannelcallback,
 	.util_init = hv_vss_init,
+	.util_init_transport = hv_vss_init_transport,
 	.util_pre_suspend = hv_vss_pre_suspend,
 	.util_pre_resume = hv_vss_pre_resume,
 	.util_deinit = hv_vss_deinit,
@@ -592,6 +594,13 @@
 	if (ret)
 		goto error;
 
+	if (srv->util_init_transport) {
+		ret = srv->util_init_transport();
+		if (ret) {
+			vmbus_close(dev->channel);
+			goto error;
+		}
+	}
 	return 0;
 
 error:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/hyperv_vmbus.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/hyperv_vmbus.h
@@ -356,12 +356,14 @@
 void vmbus_on_msg_dpc(unsigned long data);
 
 int hv_kvp_init(struct hv_util_service *srv);
+int hv_kvp_init_transport(void);
 void hv_kvp_deinit(void);
 int hv_kvp_pre_suspend(void);
 int hv_kvp_pre_resume(void);
 void hv_kvp_onchannelcallback(void *context);
 
 int hv_vss_init(struct hv_util_service *srv);
+int hv_vss_init_transport(void);
 void hv_vss_deinit(void);
 int hv_vss_pre_suspend(void);
 int hv_vss_pre_resume(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/ring_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/ring_buffer.c
@@ -249,6 +249,19 @@
 	ring_info->pkt_buffer_size = 0;
 }
 
+/*
+ * Check if the ring buffer spinlock is available to take or not; used on
+ * atomic contexts, like panic path (see the Hyper-V framebuffer driver).
+ */
+
+bool hv_ringbuffer_spinlock_busy(struct vmbus_channel *channel)
+{
+	struct hv_ring_buffer_info *rinfo = &channel->outbound;
+
+	return spin_is_locked(&rinfo->ring_lock);
+}
+EXPORT_SYMBOL_GPL(hv_ringbuffer_spinlock_busy);
+
 /* Write to the ring buffer. */
 int hv_ringbuffer_write(struct vmbus_channel *channel,
 			const struct kvec *kv_list, u32 kv_count,
@@ -408,7 +421,16 @@
 static u32 hv_pkt_iter_avail(const struct hv_ring_buffer_info *rbi)
 {
 	u32 priv_read_loc = rbi->priv_read_index;
-	u32 write_loc = READ_ONCE(rbi->ring_buffer->write_index);
+	u32 write_loc;
+
+	/*
+	 * The Hyper-V host writes the packet data, then uses
+	 * store_release() to update the write_index.  Use load_acquire()
+	 * here to prevent loads of the packet data from being re-ordered
+	 * before the read of the write_index and potentially getting
+	 * stale data.
+	 */
+	write_loc = virt_load_acquire(&rbi->ring_buffer->write_index);
 
 	if (write_loc >= priv_read_loc)
 		return write_loc - priv_read_loc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hv/vmbus_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hv/vmbus_drv.c
@@ -76,8 +76,8 @@
 
 	/*
 	 * Hyper-V should be notified only once about a panic.  If we will be
-	 * doing hyperv_report_panic_msg() later with kmsg data, don't do
-	 * the notification here.
+	 * doing hv_kmsg_dump() with kmsg data later, don't do the notification
+	 * here.
 	 */
 	if (ms_hyperv.misc_features & HV_FEATURE_GUEST_CRASH_MSR_AVAILABLE
 	    && hyperv_report_reg()) {
@@ -99,8 +99,8 @@
 
 	/*
 	 * Hyper-V should be notified only once about a panic.  If we will be
-	 * doing hyperv_report_panic_msg() later with kmsg data, don't do
-	 * the notification here.
+	 * doing hv_kmsg_dump() with kmsg data later, don't do the notification
+	 * here.
 	 */
 	if (hyperv_report_reg())
 		hyperv_report_panic(regs, val, true);
@@ -1381,7 +1381,7 @@
 			tasklet_schedule(&hv_cpu->msg_dpc);
 	}
 
-	add_interrupt_randomness(vmbus_interrupt, 0);
+	add_interrupt_randomness(vmbus_interrupt);
 }
 
 static irqreturn_t vmbus_percpu_isr(int irq, void *dev_id)
@@ -1538,21 +1538,27 @@
 	ret = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "hyperv/vmbus:online",
 				hv_synic_init, hv_synic_cleanup);
 	if (ret < 0)
-		goto err_cpuhp;
+		goto err_alloc;
 	hyperv_cpuhp_online = ret;
 
 	ret = vmbus_connect();
 	if (ret)
 		goto err_connect;
 
+	if (hv_is_isolation_supported())
+		sysctl_record_panic_msg = 0;
+
 	/*
 	 * Only register if the crash MSRs are available
 	 */
 	if (ms_hyperv.misc_features & HV_FEATURE_GUEST_CRASH_MSR_AVAILABLE) {
 		u64 hyperv_crash_ctl;
 		/*
-		 * Sysctl registration is not fatal, since by default
-		 * reporting is enabled.
+		 * Panic message recording (sysctl_record_panic_msg)
+		 * is enabled by default in non-isolated guests and
+		 * disabled by default in isolated guests; the panic
+		 * message recording won't be available in isolated
+		 * guests should the following registration fail.
 		 */
 		hv_ctl_table_hdr = register_sysctl_table(hv_root_table);
 		if (!hv_ctl_table_hdr)
@@ -1583,9 +1589,8 @@
 
 err_connect:
 	cpuhp_remove_state(hyperv_cpuhp_online);
-err_cpuhp:
-	hv_synic_free();
 err_alloc:
+	hv_synic_free();
 	if (vmbus_irq == -1) {
 		hv_remove_vmbus_handler();
 	} else {
@@ -2003,6 +2008,7 @@
 
 	return attr->mode;
 }
+EXPORT_SYMBOL_GPL(vmbus_device_unregister);
 
 static struct attribute_group vmbus_chan_group = {
 	.attrs = vmbus_chan_attrs,
@@ -2027,8 +2033,10 @@
 	kobj->kset = dev->channels_kset;
 	ret = kobject_init_and_add(kobj, &vmbus_chan_ktype, NULL,
 				   "%u", relid);
-	if (ret)
+	if (ret) {
+		kobject_put(kobj);
 		return ret;
+	}
 
 	ret = sysfs_create_group(kobj, &vmbus_chan_group);
 
@@ -2037,6 +2045,7 @@
 		 * The calling functions' error handling paths will cleanup the
 		 * empty channel directory.
 		 */
+		kobject_put(kobj);
 		dev_err(device, "Unable to set up channel sysfs files\n");
 		return ret;
 	}
@@ -2100,6 +2109,7 @@
 	ret = device_register(&child_device_obj->device);
 	if (ret) {
 		pr_err("Unable to register child device\n");
+		put_device(&child_device_obj->device);
 		return ret;
 	}
 
@@ -2331,7 +2341,7 @@
 			bool fb_overlap_ok)
 {
 	struct resource *iter, *shadow;
-	resource_size_t range_min, range_max, start;
+	resource_size_t range_min, range_max, start, end;
 	const char *dev_n = dev_name(&device_obj->device);
 	int retval;
 
@@ -2366,6 +2376,14 @@
 		range_max = iter->end;
 		start = (range_min + align - 1) & ~(align - 1);
 		for (; start + size - 1 <= range_max; start += align) {
+			end = start + size - 1;
+
+			/* Skip the whole fb_mmio region if not fb_overlap_ok */
+			if (!fb_overlap_ok && fb_mmio &&
+			    (((start >= fb_mmio->start) && (start <= fb_mmio->end)) ||
+			     ((end >= fb_mmio->start) && (end <= fb_mmio->end))))
+				continue;
+
 			shadow = __request_region(iter, start, size, NULL,
 						  IORESOURCE_BUSY);
 			if (!shadow)
@@ -2401,12 +2419,25 @@
 	struct resource *iter;
 
 	mutex_lock(&hyperv_mmio_lock);
+
+	/*
+	 * If all bytes of the MMIO range to be released are within the
+	 * special case fb_mmio shadow region, skip releasing the shadow
+	 * region since no corresponding __request_region() was done
+	 * in vmbus_allocate_mmio().
+	 */
+	if (fb_mmio && start >= fb_mmio->start &&
+	    (start + size - 1 <= fb_mmio->end))
+		goto skip_shadow_release;
+
 	for (iter = hyperv_mmio; iter; iter = iter->sibling) {
 		if ((iter->start >= start + size) || (iter->end <= start))
 			continue;
 
 		__release_region(iter, start, size);
 	}
+
+skip_shadow_release:
 	release_mem_region(start, size);
 	mutex_unlock(&hyperv_mmio_lock);
 
@@ -2773,10 +2804,15 @@
 	if (ms_hyperv.misc_features & HV_FEATURE_GUEST_CRASH_MSR_AVAILABLE) {
 		kmsg_dump_unregister(&hv_kmsg_dumper);
 		unregister_die_notifier(&hyperv_die_block);
-		atomic_notifier_chain_unregister(&panic_notifier_list,
-						 &hyperv_panic_block);
 	}
 
+	/*
+	 * The panic notifier is always registered, hence we should
+	 * also unconditionally unregister it here as well.
+	 */
+	atomic_notifier_chain_unregister(&panic_notifier_list,
+					 &hyperv_panic_block);
+
 	free_page((unsigned long)hv_panic_page);
 	unregister_sysctl_table(hv_ctl_table_hdr);
 	hv_ctl_table_hdr = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/Kconfig
@@ -38,6 +38,18 @@
 
 comment "Native drivers"
 
+config SENSORS_AAEON
+	tristate "AAEON hwmon driver"
+	depends on X86
+	depends on UBUNTU_ODM_DRIVERS
+	select MFD_AAEON
+	help
+	  This hwmon driver adds support for reporting temperature or fan
+	  speed and voltage on Single Board Computers produced by AAEON.
+
+	  This driver leverages the ASUS WMI interface to access device
+	  resources.
+
 config SENSORS_ABITUGURU
 	tristate "Abit uGuru (rev 1 & 2)"
 	depends on X86 && DMI
@@ -165,6 +177,7 @@
 	tristate "Analog Devices ADM9240 and compatibles"
 	depends on I2C
 	select HWMON_VID
+	select REGMAP_I2C
 	help
 	  If you say yes here you get support for Analog Devices ADM9240,
 	  Dallas DS1780, National Semiconductor LM81 sensor chips.
@@ -225,6 +238,7 @@
 config SENSORS_ADT7470
 	tristate "Analog Devices ADT7470"
 	depends on I2C
+	select REGMAP_I2C
 	help
 	  If you say yes here you get support for the Analog Devices
 	  ADT7470 temperature monitoring chips.
@@ -776,6 +790,7 @@
 config SENSORS_JC42
 	tristate "JEDEC JC42.4 compliant memory module temperature sensors"
 	depends on I2C
+	select REGMAP_I2C
 	help
 	  If you say yes here, you get support for JEDEC JC42.4 compliant
 	  temperature sensors, which are used on many DDR3 memory modules for
@@ -944,7 +959,7 @@
 
 config SENSORS_LTQ_CPUTEMP
 	bool "Lantiq cpu temperature sensor driver"
-	depends on LANTIQ
+	depends on SOC_XWAY
 	help
 	  If you say yes here you get support for the temperature
 	  sensor inside your CPU.
@@ -1317,7 +1332,7 @@
 	  Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658,
 	  MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696,
 	  ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG,
-	  Philips SA56004, GMT G781, and Texas Instruments TMP451
+	  Philips SA56004, GMT G781, Texas Instruments TMP451 and TMP461
 	  sensor chips.
 
 	  This driver can also be built as a module. If so, the module
@@ -1948,6 +1963,7 @@
 config SENSORS_TMP513
 	tristate "Texas Instruments TMP513 and compatibles"
 	depends on I2C
+	select REGMAP_I2C
 	help
 	  If you say yes here you get support for Texas Instruments TMP512,
 	  and TMP513 temperature and power supply sensor chips.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/Makefile
@@ -81,6 +81,7 @@
 obj-$(CONFIG_SENSORS_GSC)	+= gsc-hwmon.o
 obj-$(CONFIG_SENSORS_GPIO_FAN)	+= gpio-fan.o
 obj-$(CONFIG_SENSORS_HIH6130)	+= hih6130.o
+obj-$(CONFIG_SENSORS_AAEON)     += hwmon-aaeon.o
 obj-$(CONFIG_SENSORS_ULTRA45)	+= ultra45_env.o
 obj-$(CONFIG_SENSORS_I5500)	+= i5500_temp.o
 obj-$(CONFIG_SENSORS_I5K_AMB)	+= i5k_amb.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/acpi_power_meter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/acpi_power_meter.c
@@ -31,6 +31,7 @@
 #define POWER_METER_CAN_NOTIFY	(1 << 3)
 #define POWER_METER_IS_BATTERY	(1 << 8)
 #define UNKNOWN_HYSTERESIS	0xFFFFFFFF
+#define UNKNOWN_POWER		0xFFFFFFFF
 
 #define METER_NOTIFY_CONFIG	0x80
 #define METER_NOTIFY_TRIP	0x81
@@ -348,6 +349,9 @@
 	update_meter(resource);
 	mutex_unlock(&resource->lock);
 
+	if (resource->power == UNKNOWN_POWER)
+		return -ENODATA;
+
 	return sprintf(buf, "%llu\n", resource->power * 1000);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ad7314.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ad7314.c
@@ -22,11 +22,13 @@
  */
 #define AD7314_TEMP_MASK		0x7FE0
 #define AD7314_TEMP_SHIFT		5
+#define AD7314_LEADING_ZEROS_MASK	BIT(15)
 
 /*
  * ADT7301 and ADT7302 temperature masks
  */
 #define ADT7301_TEMP_MASK		0x3FFF
+#define ADT7301_LEADING_ZEROS_MASK	(BIT(15) | BIT(14))
 
 enum ad7314_variant {
 	adt7301,
@@ -65,12 +67,20 @@
 		return ret;
 	switch (spi_get_device_id(chip->spi_dev)->driver_data) {
 	case ad7314:
+		if (ret & AD7314_LEADING_ZEROS_MASK) {
+			/* Invalid read-out, leading zero part is missing */
+			return -EIO;
+		}
 		data = (ret & AD7314_TEMP_MASK) >> AD7314_TEMP_SHIFT;
 		data = sign_extend32(data, 9);
 
 		return sprintf(buf, "%d\n", 250 * data);
 	case adt7301:
 	case adt7302:
+		if (ret & ADT7301_LEADING_ZEROS_MASK) {
+			/* Invalid read-out, leading zero part is missing */
+			return -EIO;
+		}
 		/*
 		 * Documented as a 13 bit twos complement register
 		 * with a sign bit - which is a 14 bit 2's complement
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/adc128d818.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/adc128d818.c
@@ -176,7 +176,7 @@
 
 	mutex_lock(&data->update_lock);
 	/* 10 mV LSB on limit registers */
-	regval = clamp_val(DIV_ROUND_CLOSEST(val, 10), 0, 255);
+	regval = DIV_ROUND_CLOSEST(clamp_val(val, 0, 2550), 10);
 	data->in[index][nr] = regval << 4;
 	reg = index == 1 ? ADC128_REG_IN_MIN(nr) : ADC128_REG_IN_MAX(nr);
 	i2c_smbus_write_byte_data(data->client, reg, regval);
@@ -214,7 +214,7 @@
 		return err;
 
 	mutex_lock(&data->update_lock);
-	regval = clamp_val(DIV_ROUND_CLOSEST(val, 1000), -128, 127);
+	regval = DIV_ROUND_CLOSEST(clamp_val(val, -128000, 127000), 1000);
 	data->temp[index] = regval << 1;
 	i2c_smbus_write_byte_data(data->client,
 				  index == 1 ? ADC128_REG_TEMP_MAX
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/adt7470.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/adt7470.c
@@ -19,6 +19,7 @@
 #include <linux/log2.h>
 #include <linux/kthread.h>
 #include <linux/regmap.h>
+#include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/util_macros.h>
 
@@ -294,11 +295,10 @@
 		adt7470_read_temperatures(data);
 		mutex_unlock(&data->lock);
 
-		set_current_state(TASK_INTERRUPTIBLE);
 		if (kthread_should_stop())
 			break;
 
-		schedule_timeout(msecs_to_jiffies(data->auto_update_interval));
+		schedule_timeout_interruptible(msecs_to_jiffies(data->auto_update_interval));
 	}
 
 	return 0;
@@ -662,6 +662,9 @@
 	struct adt7470_data *data = dev_get_drvdata(dev);
 	int err;
 
+	if (val <= 0)
+		return -EINVAL;
+
 	val = FAN_RPM_TO_PERIOD(val);
 	val = clamp_val(val, 1, 65534);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/adt7475.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/adt7475.c
@@ -486,10 +486,10 @@
 		val = (temp - val) / 1000;
 
 		if (sattr->index != 1) {
-			data->temp[HYSTERSIS][sattr->index] &= 0xF0;
+			data->temp[HYSTERSIS][sattr->index] &= 0x0F;
 			data->temp[HYSTERSIS][sattr->index] |= (val & 0xF) << 4;
 		} else {
-			data->temp[HYSTERSIS][sattr->index] &= 0x0F;
+			data->temp[HYSTERSIS][sattr->index] &= 0xF0;
 			data->temp[HYSTERSIS][sattr->index] |= (val & 0xF);
 		}
 
@@ -554,11 +554,11 @@
 		val = data->enh_acoustics[0] & 0xf;
 		break;
 	case 1:
-		val = (data->enh_acoustics[1] >> 4) & 0xf;
+		val = data->enh_acoustics[1] & 0xf;
 		break;
 	case 2:
 	default:
-		val = data->enh_acoustics[1] & 0xf;
+		val = (data->enh_acoustics[1] >> 4) & 0xf;
 		break;
 	}
 
@@ -1515,9 +1515,9 @@
 	int ret, i;
 	u8 val;
 
-	ret = of_property_read_u32_array(client->dev.of_node,
-					 "adi,pwm-active-state", states,
-					 ARRAY_SIZE(states));
+	ret = device_property_read_u32_array(&client->dev,
+					     "adi,pwm-active-state", states,
+					     ARRAY_SIZE(states));
 	if (ret)
 		return ret;
 
@@ -1770,7 +1770,7 @@
 		data->pwm[CONTROL][index] &= ~0xE0;
 		data->pwm[CONTROL][index] |= (7 << 5);
 
-		i2c_smbus_write_byte_data(client, PWM_CONFIG_REG(index),
+		i2c_smbus_write_byte_data(client, PWM_REG(index),
 					  data->pwm[INPUT][index]);
 
 		i2c_smbus_write_byte_data(client, PWM_CONFIG_REG(index),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/amc6821.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/amc6821.c
@@ -934,10 +934,21 @@
 
 MODULE_DEVICE_TABLE(i2c, amc6821_id);
 
+static const struct of_device_id __maybe_unused amc6821_of_match[] = {
+	{
+		.compatible = "ti,amc6821",
+		.data = (void *)amc6821,
+	},
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, amc6821_of_match);
+
 static struct i2c_driver amc6821_driver = {
 	.class = I2C_CLASS_HWMON,
 	.driver = {
 		.name	= "amc6821",
+		.of_match_table = of_match_ptr(amc6821_of_match),
 	},
 	.probe_new = amc6821_probe,
 	.id_table = amc6821_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/aspeed-pwm-tacho.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/aspeed-pwm-tacho.c
@@ -194,6 +194,8 @@
 	u8 fan_tach_ch_source[16];
 	struct aspeed_cooling_device *cdev[8];
 	const struct attribute_group *groups[3];
+	/* protects access to shared ASPEED_PTCR_RESULT */
+	struct mutex tach_lock;
 };
 
 enum type { TYPEM, TYPEN, TYPEO };
@@ -528,6 +530,8 @@
 	u8 fan_tach_ch_source, type, mode, both;
 	int ret;
 
+	mutex_lock(&priv->tach_lock);
+
 	regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0);
 	regmap_write(priv->regmap, ASPEED_PTCR_TRIGGER, 0x1 << fan_tach_ch);
 
@@ -545,6 +549,8 @@
 		ASPEED_RPM_STATUS_SLEEP_USEC,
 		usec);
 
+	mutex_unlock(&priv->tach_lock);
+
 	/* return -ETIMEDOUT if we didn't get an answer. */
 	if (ret)
 		return ret;
@@ -904,6 +910,7 @@
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
+	mutex_init(&priv->tach_lock);
 	priv->regmap = devm_regmap_init(dev, NULL, (__force void *)regs,
 			&aspeed_pwm_tacho_regmap_config);
 	if (IS_ERR(priv->regmap))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/axi-fan-control.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/axi-fan-control.c
@@ -508,6 +508,21 @@
 		return -ENODEV;
 	}
 
+	ret = axi_fan_control_init(ctl, pdev->dev.of_node);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to initialize device\n");
+		return ret;
+	}
+
+	ctl->hdev = devm_hwmon_device_register_with_info(&pdev->dev,
+							 name,
+							 ctl,
+							 &axi_chip_info,
+							 axi_fan_control_groups);
+
+	if (IS_ERR(ctl->hdev))
+		return PTR_ERR(ctl->hdev);
+
 	ctl->irq = platform_get_irq(pdev, 0);
 	if (ctl->irq < 0)
 		return ctl->irq;
@@ -521,19 +536,7 @@
 		return ret;
 	}
 
-	ret = axi_fan_control_init(ctl, pdev->dev.of_node);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to initialize device\n");
-		return ret;
-	}
-
-	ctl->hdev = devm_hwmon_device_register_with_info(&pdev->dev,
-							 name,
-							 ctl,
-							 &axi_chip_info,
-							 axi_fan_control_groups);
-
-	return PTR_ERR_OR_ZERO(ctl->hdev);
+	return 0;
 }
 
 static struct platform_driver axi_fan_control_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/coretemp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/coretemp.c
@@ -40,15 +40,12 @@
 
 #define PKG_SYSFS_ATTR_NO	1	/* Sysfs attribute for package temp */
 #define BASE_SYSFS_ATTR_NO	2	/* Sysfs Base attr no for coretemp */
-#define NUM_REAL_CORES		128	/* Number of Real cores per cpu */
-#define CORETEMP_NAME_LENGTH	19	/* String Length of attrs */
+#define NUM_REAL_CORES		512	/* Number of Real cores per cpu */
+#define CORETEMP_NAME_LENGTH	28	/* String Length of attrs */
 #define MAX_CORE_ATTRS		4	/* Maximum no of basic attrs */
 #define TOTAL_ATTRS		(MAX_CORE_ATTRS + 1)
 #define MAX_CORE_DATA		(NUM_REAL_CORES + BASE_SYSFS_ATTR_NO)
 
-#define TO_CORE_ID(cpu)		(cpu_data(cpu).cpu_core_id)
-#define TO_ATTR_NO(cpu)		(TO_CORE_ID(cpu) + BASE_SYSFS_ATTR_NO)
-
 #ifdef CONFIG_SMP
 #define for_each_sibling(i, cpu) \
 	for_each_cpu(i, topology_sibling_cpumask(cpu))
@@ -91,6 +88,8 @@
 struct platform_data {
 	struct device		*hwmon_dev;
 	u16			pkg_id;
+	u16			cpu_map[NUM_REAL_CORES];
+	struct ida		ida;
 	struct cpumask		cpumask;
 	struct temp_data	*core_data[MAX_CORE_DATA];
 	struct device_attribute name_attr;
@@ -243,10 +242,13 @@
 	 */
 	if (host_bridge && host_bridge->vendor == PCI_VENDOR_ID_INTEL) {
 		for (i = 0; i < ARRAY_SIZE(tjmax_pci_table); i++) {
-			if (host_bridge->device == tjmax_pci_table[i].device)
+			if (host_bridge->device == tjmax_pci_table[i].device) {
+				pci_dev_put(host_bridge);
 				return tjmax_pci_table[i].tjmax;
+			}
 		}
 	}
+	pci_dev_put(host_bridge);
 
 	for (i = 0; i < ARRAY_SIZE(tjmax_table); i++) {
 		if (strstr(c->x86_model_id, tjmax_table[i].id))
@@ -378,7 +380,7 @@
 }
 
 static int create_core_attrs(struct temp_data *tdata, struct device *dev,
-			     int attr_no)
+			     int index)
 {
 	int i;
 	static ssize_t (*const rd_ptr[TOTAL_ATTRS]) (struct device *dev,
@@ -390,13 +392,20 @@
 	};
 
 	for (i = 0; i < tdata->attr_size; i++) {
+		/*
+		 * We map the attr number to core id of the CPU
+		 * The attr number is always core id + 2
+		 * The Pkgtemp will always show up as temp1_*, if available
+		 */
+		int attr_no = tdata->is_pkg_data ? 1 : tdata->cpu_core_id + 2;
+
 		snprintf(tdata->attr_name[i], CORETEMP_NAME_LENGTH,
 			 "temp%d_%s", attr_no, suffixes[i]);
 		sysfs_attr_init(&tdata->sd_attrs[i].dev_attr.attr);
 		tdata->sd_attrs[i].dev_attr.attr.name = tdata->attr_name[i];
 		tdata->sd_attrs[i].dev_attr.attr.mode = 0444;
 		tdata->sd_attrs[i].dev_attr.show = rd_ptr[i];
-		tdata->sd_attrs[i].index = attr_no;
+		tdata->sd_attrs[i].index = index;
 		tdata->attrs[i] = &tdata->sd_attrs[i].dev_attr.attr;
 	}
 	tdata->attr_group.attrs = tdata->attrs;
@@ -441,7 +450,7 @@
 							MSR_IA32_THERM_STATUS;
 	tdata->is_pkg_data = pkg_flag;
 	tdata->cpu = cpu;
-	tdata->cpu_core_id = TO_CORE_ID(cpu);
+	tdata->cpu_core_id = topology_core_id(cpu);
 	tdata->attr_size = MAX_CORE_ATTRS;
 	mutex_init(&tdata->update_lock);
 	return tdata;
@@ -454,22 +463,29 @@
 	struct platform_data *pdata = platform_get_drvdata(pdev);
 	struct cpuinfo_x86 *c = &cpu_data(cpu);
 	u32 eax, edx;
-	int err, attr_no;
+	int err, index;
 
 	/*
-	 * Find attr number for sysfs:
-	 * We map the attr number to core id of the CPU
-	 * The attr number is always core id + 2
-	 * The Pkgtemp will always show up as temp1_*, if available
+	 * Get the index of tdata in pdata->core_data[]
+	 * tdata for package: pdata->core_data[1]
+	 * tdata for core: pdata->core_data[2] .. pdata->core_data[NUM_REAL_CORES + 1]
 	 */
-	attr_no = pkg_flag ? PKG_SYSFS_ATTR_NO : TO_ATTR_NO(cpu);
+	if (pkg_flag) {
+		index = PKG_SYSFS_ATTR_NO;
+	} else {
+		index = ida_alloc_max(&pdata->ida, NUM_REAL_CORES - 1, GFP_KERNEL);
+		if (index < 0)
+			return index;
 
-	if (attr_no > MAX_CORE_DATA - 1)
-		return -ERANGE;
+		pdata->cpu_map[index] = topology_core_id(cpu);
+		index += BASE_SYSFS_ATTR_NO;
+	}
 
 	tdata = init_temp_data(cpu, pkg_flag);
-	if (!tdata)
-		return -ENOMEM;
+	if (!tdata) {
+		err = -ENOMEM;
+		goto ida_free;
+	}
 
 	/* Test if we can access the status register */
 	err = rdmsr_safe_on_cpu(cpu, tdata->status_reg, &eax, &edx);
@@ -494,17 +510,20 @@
 		}
 	}
 
-	pdata->core_data[attr_no] = tdata;
+	pdata->core_data[index] = tdata;
 
 	/* Create sysfs interfaces */
-	err = create_core_attrs(tdata, pdata->hwmon_dev, attr_no);
+	err = create_core_attrs(tdata, pdata->hwmon_dev, index);
 	if (err)
 		goto exit_free;
 
 	return 0;
 exit_free:
-	pdata->core_data[attr_no] = NULL;
+	pdata->core_data[index] = NULL;
 	kfree(tdata);
+ida_free:
+	if (!pkg_flag)
+		ida_free(&pdata->ida, index - BASE_SYSFS_ATTR_NO);
 	return err;
 }
 
@@ -519,71 +538,63 @@
 {
 	struct temp_data *tdata = pdata->core_data[indx];
 
+	/* if we errored on add then this is already gone */
+	if (!tdata)
+		return;
+
 	/* Remove the sysfs attributes */
 	sysfs_remove_group(&pdata->hwmon_dev->kobj, &tdata->attr_group);
 
 	kfree(pdata->core_data[indx]);
 	pdata->core_data[indx] = NULL;
+
+	if (indx >= BASE_SYSFS_ATTR_NO)
+		ida_free(&pdata->ida, indx - BASE_SYSFS_ATTR_NO);
 }
 
-static int coretemp_probe(struct platform_device *pdev)
+static int coretemp_device_add(int zoneid)
 {
-	struct device *dev = &pdev->dev;
+	struct platform_device *pdev;
 	struct platform_data *pdata;
+	int err;
 
 	/* Initialize the per-zone data structures */
-	pdata = devm_kzalloc(dev, sizeof(struct platform_data), GFP_KERNEL);
+	pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
 	if (!pdata)
 		return -ENOMEM;
 
-	pdata->pkg_id = pdev->id;
-	platform_set_drvdata(pdev, pdata);
+	pdata->pkg_id = zoneid;
+	ida_init(&pdata->ida);
 
-	pdata->hwmon_dev = devm_hwmon_device_register_with_groups(dev, DRVNAME,
-								  pdata, NULL);
-	return PTR_ERR_OR_ZERO(pdata->hwmon_dev);
-}
-
-static int coretemp_remove(struct platform_device *pdev)
-{
-	struct platform_data *pdata = platform_get_drvdata(pdev);
-	int i;
+	pdev = platform_device_alloc(DRVNAME, zoneid);
+	if (!pdev) {
+		err = -ENOMEM;
+		goto err_free_pdata;
+	}
 
-	for (i = MAX_CORE_DATA - 1; i >= 0; --i)
-		if (pdata->core_data[i])
-			coretemp_remove_core(pdata, i);
+	err = platform_device_add(pdev);
+	if (err)
+		goto err_put_dev;
 
+	platform_set_drvdata(pdev, pdata);
+	zone_devices[zoneid] = pdev;
 	return 0;
-}
 
-static struct platform_driver coretemp_driver = {
-	.driver = {
-		.name = DRVNAME,
-	},
-	.probe = coretemp_probe,
-	.remove = coretemp_remove,
-};
+err_put_dev:
+	platform_device_put(pdev);
+err_free_pdata:
+	kfree(pdata);
+	return err;
+}
 
-static struct platform_device *coretemp_device_add(unsigned int cpu)
+static void coretemp_device_remove(int zoneid)
 {
-	int err, zoneid = topology_logical_die_id(cpu);
-	struct platform_device *pdev;
-
-	if (zoneid < 0)
-		return ERR_PTR(-ENOMEM);
-
-	pdev = platform_device_alloc(DRVNAME, zoneid);
-	if (!pdev)
-		return ERR_PTR(-ENOMEM);
-
-	err = platform_device_add(pdev);
-	if (err) {
-		platform_device_put(pdev);
-		return ERR_PTR(err);
-	}
+	struct platform_device *pdev = zone_devices[zoneid];
+	struct platform_data *pdata = platform_get_drvdata(pdev);
 
-	zone_devices[zoneid] = pdev;
-	return pdev;
+	ida_destroy(&pdata->ida);
+	kfree(pdata);
+	platform_device_unregister(pdev);
 }
 
 static int coretemp_cpu_online(unsigned int cpu)
@@ -607,7 +618,10 @@
 	if (!cpu_has(c, X86_FEATURE_DTHERM))
 		return -ENODEV;
 
-	if (!pdev) {
+	pdata = platform_get_drvdata(pdev);
+	if (!pdata->hwmon_dev) {
+		struct device *hwmon;
+
 		/* Check the microcode version of the CPU */
 		if (chk_ucode_version(cpu))
 			return -EINVAL;
@@ -618,9 +632,11 @@
 		 * online. So, initialize per-pkg data structures and
 		 * then bring this core online.
 		 */
-		pdev = coretemp_device_add(cpu);
-		if (IS_ERR(pdev))
-			return PTR_ERR(pdev);
+		hwmon = hwmon_device_register_with_groups(&pdev->dev, DRVNAME,
+							  pdata, NULL);
+		if (IS_ERR(hwmon))
+			return PTR_ERR(hwmon);
+		pdata->hwmon_dev = hwmon;
 
 		/*
 		 * Check whether pkgtemp support is available.
@@ -630,7 +646,6 @@
 			coretemp_add_core(pdev, cpu, 1);
 	}
 
-	pdata = platform_get_drvdata(pdev);
 	/*
 	 * Check whether a thread sibling is already online. If not add the
 	 * interface for this CPU core.
@@ -647,25 +662,28 @@
 	struct platform_device *pdev = coretemp_get_pdev(cpu);
 	struct platform_data *pd;
 	struct temp_data *tdata;
-	int indx, target;
+	int i, indx = -1, target;
 
-	/*
-	 * Don't execute this on suspend as the device remove locks
-	 * up the machine.
-	 */
+	/* No need to tear down any interfaces for suspend */
 	if (cpuhp_tasks_frozen)
 		return 0;
 
 	/* If the physical CPU device does not exist, just return */
-	if (!pdev)
+	pd = platform_get_drvdata(pdev);
+	if (!pd->hwmon_dev)
 		return 0;
 
-	/* The core id is too big, just return */
-	indx = TO_ATTR_NO(cpu);
-	if (indx > MAX_CORE_DATA - 1)
+	for (i = 0; i < NUM_REAL_CORES; i++) {
+		if (pd->cpu_map[i] == topology_core_id(cpu)) {
+			indx = i + BASE_SYSFS_ATTR_NO;
+			break;
+		}
+	}
+
+	/* Too many cores and this core is not populated, just return */
+	if (indx < 0)
 		return 0;
 
-	pd = platform_get_drvdata(pdev);
 	tdata = pd->core_data[indx];
 
 	cpumask_clear_cpu(cpu, &pd->cpumask);
@@ -685,13 +703,14 @@
 	}
 
 	/*
-	 * If all cores in this pkg are offline, remove the device. This
-	 * will invoke the platform driver remove function, which cleans up
-	 * the rest.
+	 * If all cores in this pkg are offline, remove the interface.
 	 */
+	tdata = pd->core_data[PKG_SYSFS_ATTR_NO];
 	if (cpumask_empty(&pd->cpumask)) {
-		zone_devices[topology_logical_die_id(cpu)] = NULL;
-		platform_device_unregister(pdev);
+		if (tdata)
+			coretemp_remove_core(pd, PKG_SYSFS_ATTR_NO);
+		hwmon_device_unregister(pd->hwmon_dev);
+		pd->hwmon_dev = NULL;
 		return 0;
 	}
 
@@ -699,7 +718,6 @@
 	 * Check whether this core is the target for the package
 	 * interface. We need to assign it to some other cpu.
 	 */
-	tdata = pd->core_data[PKG_SYSFS_ATTR_NO];
 	if (tdata && tdata->cpu == cpu) {
 		target = cpumask_first(&pd->cpumask);
 		mutex_lock(&tdata->update_lock);
@@ -718,7 +736,7 @@
 
 static int __init coretemp_init(void)
 {
-	int err;
+	int i, err;
 
 	/*
 	 * CPUID.06H.EAX[0] indicates whether the CPU has thermal
@@ -734,20 +752,22 @@
 	if (!zone_devices)
 		return -ENOMEM;
 
-	err = platform_driver_register(&coretemp_driver);
-	if (err)
-		goto outzone;
+	for (i = 0; i < max_zones; i++) {
+		err = coretemp_device_add(i);
+		if (err)
+			goto outzone;
+	}
 
 	err = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "hwmon/coretemp:online",
 				coretemp_cpu_online, coretemp_cpu_offline);
 	if (err < 0)
-		goto outdrv;
+		goto outzone;
 	coretemp_hp_online = err;
 	return 0;
 
-outdrv:
-	platform_driver_unregister(&coretemp_driver);
 outzone:
+	while (i--)
+		coretemp_device_remove(i);
 	kfree(zone_devices);
 	return err;
 }
@@ -755,8 +775,11 @@
 
 static void __exit coretemp_exit(void)
 {
+	int i;
+
 	cpuhp_remove_state(coretemp_hp_online);
-	platform_driver_unregister(&coretemp_driver);
+	for (i = 0; i < max_zones; i++)
+		coretemp_device_remove(i);
 	kfree(zone_devices);
 }
 module_exit(coretemp_exit)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/corsair-cpro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/corsair-cpro.c
@@ -16,6 +16,7 @@
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 #include <linux/types.h>
 
 #define USB_VENDOR_ID_CORSAIR			0x1b1c
@@ -77,8 +78,11 @@
 struct ccp_device {
 	struct hid_device *hdev;
 	struct device *hwmon_dev;
+	/* For reinitializing the completion below */
+	spinlock_t wait_input_report_lock;
 	struct completion wait_input_report;
 	struct mutex mutex; /* whenever buffer is used, lock before send_usb_cmd */
+	u8 *cmd_buffer;
 	u8 *buffer;
 	int target[6];
 	DECLARE_BITMAP(temp_cnct, NUM_TEMP_SENSORS);
@@ -111,15 +115,23 @@
 	unsigned long t;
 	int ret;
 
-	memset(ccp->buffer, 0x00, OUT_BUFFER_SIZE);
-	ccp->buffer[0] = command;
-	ccp->buffer[1] = byte1;
-	ccp->buffer[2] = byte2;
-	ccp->buffer[3] = byte3;
-
+	memset(ccp->cmd_buffer, 0x00, OUT_BUFFER_SIZE);
+	ccp->cmd_buffer[0] = command;
+	ccp->cmd_buffer[1] = byte1;
+	ccp->cmd_buffer[2] = byte2;
+	ccp->cmd_buffer[3] = byte3;
+
+	/*
+	 * Disable raw event parsing for a moment to safely reinitialize the
+	 * completion. Reinit is done because hidraw could have triggered
+	 * the raw event parsing and marked the ccp->wait_input_report
+	 * completion as done.
+	 */
+	spin_lock_bh(&ccp->wait_input_report_lock);
 	reinit_completion(&ccp->wait_input_report);
+	spin_unlock_bh(&ccp->wait_input_report_lock);
 
-	ret = hid_hw_output_report(ccp->hdev, ccp->buffer, OUT_BUFFER_SIZE);
+	ret = hid_hw_output_report(ccp->hdev, ccp->cmd_buffer, OUT_BUFFER_SIZE);
 	if (ret < 0)
 		return ret;
 
@@ -135,11 +147,12 @@
 	struct ccp_device *ccp = hid_get_drvdata(hdev);
 
 	/* only copy buffer when requested */
-	if (completion_done(&ccp->wait_input_report))
-		return 0;
-
-	memcpy(ccp->buffer, data, min(IN_BUFFER_SIZE, size));
-	complete(&ccp->wait_input_report);
+	spin_lock(&ccp->wait_input_report_lock);
+	if (!completion_done(&ccp->wait_input_report)) {
+		memcpy(ccp->buffer, data, min(IN_BUFFER_SIZE, size));
+		complete_all(&ccp->wait_input_report);
+	}
+	spin_unlock(&ccp->wait_input_report_lock);
 
 	return 0;
 }
@@ -492,7 +505,11 @@
 	if (!ccp)
 		return -ENOMEM;
 
-	ccp->buffer = devm_kmalloc(&hdev->dev, OUT_BUFFER_SIZE, GFP_KERNEL);
+	ccp->cmd_buffer = devm_kmalloc(&hdev->dev, OUT_BUFFER_SIZE, GFP_KERNEL);
+	if (!ccp->cmd_buffer)
+		return -ENOMEM;
+
+	ccp->buffer = devm_kmalloc(&hdev->dev, IN_BUFFER_SIZE, GFP_KERNEL);
 	if (!ccp->buffer)
 		return -ENOMEM;
 
@@ -510,7 +527,9 @@
 
 	ccp->hdev = hdev;
 	hid_set_drvdata(hdev, ccp);
+
 	mutex_init(&ccp->mutex);
+	spin_lock_init(&ccp->wait_input_report_lock);
 	init_completion(&ccp->wait_input_report);
 
 	hid_device_io_start(hdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/corsair-psu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/corsair-psu.c
@@ -729,7 +729,7 @@
 	corsairpsu_check_cmd_support(priv);
 
 	priv->hwmon_dev = hwmon_device_register_with_info(&hdev->dev, "corsairpsu", priv,
-							  &corsairpsu_chip_info, 0);
+							  &corsairpsu_chip_info, NULL);
 
 	if (IS_ERR(priv->hwmon_dev)) {
 		ret = PTR_ERR(priv->hwmon_dev);
@@ -808,7 +808,23 @@
 	.reset_resume	= corsairpsu_resume,
 #endif
 };
-module_hid_driver(corsairpsu_driver);
+
+static int __init corsair_init(void)
+{
+	return hid_register_driver(&corsairpsu_driver);
+}
+
+static void __exit corsair_exit(void)
+{
+	hid_unregister_driver(&corsairpsu_driver);
+}
+
+/*
+ * With module_init() the driver would load before the HID bus when
+ * built-in, so use late_initcall() instead.
+ */
+late_initcall(corsair_init);
+module_exit(corsair_exit);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Wilken Gottwalt <wilken.gottwalt@posteo.net>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/dell-smm-hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/dell-smm-hwmon.c
@@ -326,7 +326,7 @@
 }
 
 /*
- * Set the fan speed (off, low, high). Returns the new fan status.
+ * Set the fan speed (off, low, high, ...).
  */
 static int i8k_set_fan(const struct dell_smm_data *data, int fan, int speed)
 {
@@ -338,7 +338,7 @@
 	speed = (speed < 0) ? 0 : ((speed > data->i8k_fan_max) ? data->i8k_fan_max : speed);
 	regs.ebx = (fan & 0xff) | (speed << 8);
 
-	return i8k_smm(&regs) ? : i8k_get_fan_status(data, fan);
+	return i8k_smm(&regs);
 }
 
 static int __init i8k_get_temp_type(int sensor)
@@ -452,7 +452,7 @@
 i8k_ioctl_unlocked(struct file *fp, struct dell_smm_data *data, unsigned int cmd, unsigned long arg)
 {
 	int val = 0;
-	int speed;
+	int speed, err;
 	unsigned char buff[16];
 	int __user *argp = (int __user *)arg;
 
@@ -513,7 +513,11 @@
 		if (copy_from_user(&speed, argp + 1, sizeof(int)))
 			return -EFAULT;
 
-		val = i8k_set_fan(data, val, speed);
+		err = i8k_set_fan(data, val, speed);
+		if (err < 0)
+			return err;
+
+		val = i8k_get_fan_status(data, val);
 		break;
 
 	default:
@@ -623,10 +627,9 @@
 {
 	struct dell_smm_data *data = dev_get_drvdata(dev);
 
-	/* Register the proc entry */
-	proc_create_data("i8k", 0, NULL, &i8k_proc_ops, data);
-
-	devm_add_action_or_reset(dev, i8k_exit_procfs, NULL);
+	/* Only register exit function if creation was successful */
+	if (proc_create_data("i8k", 0, NULL, &i8k_proc_ops, data))
+		devm_add_action_or_reset(dev, i8k_exit_procfs, NULL);
 }
 
 #else
@@ -1195,6 +1198,14 @@
 		},
 		.driver_data = (void *)&i8k_fan_control_data[I8K_FAN_34A3_35A3],
 	},
+	{
+		.ident = "Dell XPS 13 7390",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "XPS 13 7390"),
+		},
+		.driver_data = (void *)&i8k_fan_control_data[I8K_FAN_34A3_35A3],
+	},
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/drivetemp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/drivetemp.c
@@ -621,3 +621,4 @@
 MODULE_AUTHOR("Guenter Roeck <linus@roeck-us.net>");
 MODULE_DESCRIPTION("Hard drive temperature monitor");
 MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:drivetemp");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/f71882fg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/f71882fg.c
@@ -1577,8 +1577,9 @@
 		temp *= 125;
 		if (sign)
 			temp -= 128000;
-	} else
-		temp = data->temp[nr] * 1000;
+	} else {
+		temp = ((s8)data->temp[nr]) * 1000;
+	}
 
 	return sprintf(buf, "%d\n", temp);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ftsteutates.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ftsteutates.c
@@ -12,6 +12,7 @@
 #include <linux/i2c.h>
 #include <linux/init.h>
 #include <linux/jiffies.h>
+#include <linux/math.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
@@ -347,13 +348,15 @@
 {
 	struct fts_data *data = dev_get_drvdata(dev);
 	int index = to_sensor_dev_attr(devattr)->index;
-	int err;
+	int value, err;
 
 	err = fts_update_device(data);
 	if (err < 0)
 		return err;
 
-	return sprintf(buf, "%u\n", data->volt[index]);
+	value = DIV_ROUND_CLOSEST(data->volt[index] * 3300, 255);
+
+	return sprintf(buf, "%d\n", value);
 }
 
 static ssize_t temp_value_show(struct device *dev,
@@ -361,13 +364,15 @@
 {
 	struct fts_data *data = dev_get_drvdata(dev);
 	int index = to_sensor_dev_attr(devattr)->index;
-	int err;
+	int value, err;
 
 	err = fts_update_device(data);
 	if (err < 0)
 		return err;
 
-	return sprintf(buf, "%u\n", data->temp_input[index]);
+	value = (data->temp_input[index] - 64) * 1000;
+
+	return sprintf(buf, "%d\n", value);
 }
 
 static ssize_t temp_fault_show(struct device *dev,
@@ -436,13 +441,15 @@
 {
 	struct fts_data *data = dev_get_drvdata(dev);
 	int index = to_sensor_dev_attr(devattr)->index;
-	int err;
+	int value, err;
 
 	err = fts_update_device(data);
 	if (err < 0)
 		return err;
 
-	return sprintf(buf, "%u\n", data->fan_input[index]);
+	value = data->fan_input[index] * 60;
+
+	return sprintf(buf, "%d\n", value);
 }
 
 static ssize_t fan_source_show(struct device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/gpio-fan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/gpio-fan.c
@@ -391,6 +391,9 @@
 	if (!fan_data)
 		return -EINVAL;
 
+	if (state >= fan_data->num_speed)
+		return -EINVAL;
+
 	set_fan_speed(fan_data, state);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/gsc-hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/gsc-hwmon.c
@@ -82,8 +82,8 @@
 	if (kstrtol(buf, 10, &temp))
 		return -EINVAL;
 
-	temp = clamp_val(temp, 0, 10000);
-	temp = DIV_ROUND_CLOSEST(temp, 10);
+	temp = clamp_val(temp, 0, 100000);
+	temp = DIV_ROUND_CLOSEST(temp, 100);
 
 	regs[0] = temp & 0xff;
 	regs[1] = (temp >> 8) & 0xff;
@@ -100,7 +100,7 @@
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
 
-	return sprintf(buf, "%d\n", 255 * (50 + (attr->index * 10)) / 100);
+	return sprintf(buf, "%d\n", 255 * (50 + (attr->index * 10)));
 }
 
 static SENSOR_DEVICE_ATTR_RO(pwm1_auto_point1_pwm, pwm_auto_point_pwm, 0);
@@ -267,6 +267,7 @@
 	pdata->nchannels = nchannels;
 
 	/* fan controller base address */
+	of_node_get(dev->parent->of_node);
 	fan = of_find_compatible_node(dev->parent->of_node, NULL, "gw,gsc-fan");
 	if (fan && of_property_read_u32(fan, "reg", &pdata->fan_base)) {
 		dev_err(dev, "fan node without base\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/hwmon-aaeon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/hwmon-aaeon.c
@@ -0,0 +1,568 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * AAEON HWMON driver
+ * Copyright (c) 2021, AAEON Ltd.
+ *
+ * Author: Edward Lin	<edward1_lin@aaeon.com.tw>
+ * Author: Kunyang Fan	<kunyang_fan@aaeon.com.tw>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/acpi.h>
+#include <linux/err.h>
+#include <linux/jiffies.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_data/x86/asus-wmi.h>
+#include <linux/platform_device.h>
+
+#define DRVNAME "hwmon-aaeon"
+
+#define AAEON_WMI_MGMT_GUID		"97845ED0-4E6D-11DE-8A39-0800200C9A66"
+
+#define AAEON_VERSION_METHOD_ID		0x00000000
+#define HWM_INFORMATION_METHOD_ID	0x00030000
+#define HWM_METHOD_ID				0x00030001
+
+#define BITMAP_TEMP_ARG			0x12
+#define BITMAP_FAN_ARG			0x13
+#define BITMAP_VOLTAGE_ARG		0x14
+
+#define SENSOR_TEMP_NUMBER		0
+#define SENSOR_FAN_NUMBER		1
+#define SENSOR_VOLTAGE_NUMBER	2
+#define SENSOR_MAX_NUMBER		2
+
+static ssize_t aaeon_show_sensor(struct device *dev,
+			       struct device_attribute *devattr, char *buf);
+static ssize_t aaeon_show_sensor_name(struct device *dev,
+				    struct device_attribute *devattr,
+				    char *buf);
+static ssize_t aaeon_show_version(struct device *dev,
+				  struct device_attribute *devattr, char *buf);
+static ssize_t name_show(struct device *dev, struct device_attribute *devattr,
+			 char *buf);
+static int aaeon_get_version(void);
+static int aaeon_hwmon_probe(struct platform_device *pdev);
+static int aaeon_hwmon_remove(struct platform_device *pdev);
+
+static const char * const temp_sensors_name_table[] = {
+			"CPU_Temp",
+			"SYS1_Temp",
+			"SYS2_Temp",
+};
+
+static const char * const temp_sensors_name_table_V3[] = {
+			"SYS_Temp",
+			"CPU_Temp",
+};
+
+static const char * const fan_sensors_name_table[] = {
+			"CPU_FAN",
+			"SYS1_FAN",
+			"SYS2_FAN",
+			"Chasis1_FAN",
+			"Chasis2_FAN",
+};
+
+static const char * const fan_sensors_name_table_V3[] = {
+			"Chasis_FAN",
+			"CPU_FAN",
+};
+
+static const char * const voltage_sensors_name_table[] = {
+			"VCORE_Voltage",
+			"VMEM_Voltage",
+			"+12_Voltage",
+			"+5_Voltage",
+			"+3.3_Voltage",
+			"+1.8_Voltage",
+			"5VSB_Voltage",
+			"3VSB_Voltage",
+			"VBAT_Voltage",
+};
+
+static const char * const voltage_sensors_name_table_V3[] = {
+			"VCORE_Voltage",
+			"+5_Voltage",
+			"AVCC_Voltage",
+			"+3.3_Voltage",
+			"+12_Voltage",
+			"VCOREREFIN_Voltage",
+			"VIN4_Voltage",
+			"3VSB_Voltage",
+			"VBAT_Voltage",
+};
+
+struct aaeon_hwmon_data {
+	struct device *hwmon_dev;
+	int bfpi_version;
+	u32 temp_bitmap;
+	u32 fan_bitmap;
+	u32 voltage_bitmap;
+	unsigned int sensors_number[SENSOR_MAX_NUMBER + 1];
+	const char * const *temp_names;
+	const char * const *fan_names;
+	const char * const *voltage_names;
+};
+
+/* Temperature attributes */
+static struct sensor_device_attribute_2 temp_sys_nodes_atts[] = {
+	SENSOR_ATTR_2(temp1_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_TEMP_NUMBER, 0),
+	SENSOR_ATTR_2(temp1_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_TEMP_NUMBER, 0),
+	SENSOR_ATTR_2(temp2_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_TEMP_NUMBER, 1),
+	SENSOR_ATTR_2(temp2_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_TEMP_NUMBER, 1),
+	SENSOR_ATTR_2(temp3_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_TEMP_NUMBER, 2),
+	SENSOR_ATTR_2(temp3_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_TEMP_NUMBER, 2),
+};
+
+/* Cooler Fan attributes */
+static struct sensor_device_attribute_2 fan_sys_nodes_atts[] = {
+	SENSOR_ATTR_2(fan1_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_FAN_NUMBER, 0),
+	SENSOR_ATTR_2(fan1_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_FAN_NUMBER, 0),
+	SENSOR_ATTR_2(fan2_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_FAN_NUMBER, 1),
+	SENSOR_ATTR_2(fan2_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_FAN_NUMBER, 1),
+	SENSOR_ATTR_2(fan3_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_FAN_NUMBER, 2),
+	SENSOR_ATTR_2(fan3_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_FAN_NUMBER, 2),
+	SENSOR_ATTR_2(fan4_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_FAN_NUMBER, 3),
+	SENSOR_ATTR_2(fan4_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_FAN_NUMBER, 3),
+	SENSOR_ATTR_2(fan5_input, 0444, aaeon_show_sensor, NULL,
+				SENSOR_FAN_NUMBER, 4),
+	SENSOR_ATTR_2(fan5_label, 0444, aaeon_show_sensor_name, NULL,
+				SENSOR_FAN_NUMBER, 4),
+};
+
+/* Voltage attributes */
+static struct sensor_device_attribute_2 voltage_sys_nodes_atts[] = {
+	SENSOR_ATTR_2(in1_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 0),
+	SENSOR_ATTR_2(in1_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 0),
+	SENSOR_ATTR_2(in2_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 1),
+	SENSOR_ATTR_2(in2_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 1),
+	SENSOR_ATTR_2(in3_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 2),
+	SENSOR_ATTR_2(in3_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 2),
+	SENSOR_ATTR_2(in4_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 3),
+	SENSOR_ATTR_2(in4_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 3),
+	SENSOR_ATTR_2(in5_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 4),
+	SENSOR_ATTR_2(in5_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 4),
+	SENSOR_ATTR_2(in6_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 5),
+	SENSOR_ATTR_2(in6_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 5),
+	SENSOR_ATTR_2(in7_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 6),
+	SENSOR_ATTR_2(in7_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 6),
+	SENSOR_ATTR_2(in8_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 7),
+	SENSOR_ATTR_2(in8_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 7),
+	SENSOR_ATTR_2(in9_input, 0444, aaeon_show_sensor, NULL,
+			SENSOR_VOLTAGE_NUMBER, 8),
+	SENSOR_ATTR_2(in9_label, 0444, aaeon_show_sensor_name, NULL,
+			SENSOR_VOLTAGE_NUMBER, 8),
+
+};
+
+static struct sensor_device_attribute_2 info_sys_nodes_atts[] = {
+	/* WMI version Information */
+	SENSOR_ATTR_2(AAEON_VERSION, 0444, aaeon_show_version, NULL, 0, 0),
+};
+
+DEVICE_ATTR_RO(name);
+static ssize_t name_show(struct device *dev, struct device_attribute *devattr,
+			 char *buf)
+{
+	return sprintf(buf, "%s\n", DRVNAME);
+}
+
+static ssize_t aaeon_show_version(struct device *dev,
+				  struct device_attribute *devattr, char *buf)
+{
+	struct aaeon_hwmon_data *data =
+			(struct aaeon_hwmon_data *)dev_get_drvdata(dev);
+
+	return sprintf(buf, "%d\n", data->bfpi_version);
+}
+
+static ssize_t aaeon_show_sensor_name(struct device *dev,
+				    struct device_attribute *devattr, char *buf)
+{
+	u8 nr = to_sensor_dev_attr_2(devattr)->nr;
+	u8 index = to_sensor_dev_attr_2(devattr)->index;
+	struct aaeon_hwmon_data *data =
+			(struct aaeon_hwmon_data *)dev_get_drvdata(dev);
+
+	if (nr > SENSOR_MAX_NUMBER || index >= data->sensors_number[nr]) {
+		pr_debug("Can not check the device");
+		return -1;
+	}
+
+	switch (nr) {
+	case SENSOR_TEMP_NUMBER:
+		return sprintf(buf, "%s\n", data->temp_names[index]);
+	case SENSOR_FAN_NUMBER:
+		return sprintf(buf, "%s\n", data->fan_names[index]);
+	case SENSOR_VOLTAGE_NUMBER:
+		return sprintf(buf, "%s\n", data->voltage_names[index]);
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+static ssize_t aaeon_show_sensor(struct device *dev,
+			       struct device_attribute *devattr, char *buf)
+{
+	u8 nr = to_sensor_dev_attr_2(devattr)->nr;
+	u8 index = to_sensor_dev_attr_2(devattr)->index;
+	u32 dev_id;
+	int retval, err;
+	struct aaeon_hwmon_data *data =
+			(struct aaeon_hwmon_data *)dev_get_drvdata(dev);
+
+	if (nr > SENSOR_MAX_NUMBER || index >= data->sensors_number[nr]) {
+		pr_debug("Can not check the device");
+		return -1;
+	}
+
+	/* For the V3 version, index need offset */
+	if (data->bfpi_version == 0x03 && nr != SENSOR_VOLTAGE_NUMBER)
+		index++;
+
+	dev_id = (index << 12) | (nr << 8);
+	err = asus_wmi_evaluate_method(HWM_METHOD_ID, dev_id, 0, &retval);
+	if (err)
+		return err;
+
+	/* For the V3 version, need to convert the raw value*/
+	if (nr == SENSOR_VOLTAGE_NUMBER && data->bfpi_version == 0x03) {
+		switch (index) {
+		case 0: /* VCORE */
+			retval = retval * 16;
+			break;
+		case 1: /* +5V */
+			retval = (retval * 2008) / 50;
+			break;
+		case 2: /* AVCC */
+			retval = retval * 16;
+			break;
+		case 3: /* +3.3V */
+			retval = retval * 16;
+			break;
+		case 4: /* +12V */
+			retval = retval * 96;
+			break;
+		case 5: /* VCOREREFIN */
+			retval = (retval * 552) / 41;
+			break;
+		case 6: /* VIN4 */
+			retval = retval * 8;
+			break;
+		case 7: /* 3VSB */
+			retval = retval * 16;
+			break;
+		case 8: /* VBAT */
+			retval = retval * 16;
+			break;
+		default:
+			break;
+		}
+	} else if (nr == SENSOR_TEMP_NUMBER && data->bfpi_version == 0x03)
+		retval = retval * 1000;
+
+	return sprintf(buf, "%d\n", retval);
+}
+
+static int aaeon_hwmon_create_sub_sysfs_fs(struct platform_device *pdev,
+					struct sensor_device_attribute_2 *attr,
+					int sensor_number,
+					u32 sensor_mask,
+					int bfpi_version)
+{
+	int i, err = 0;
+
+	for (i = 0; i < sensor_number; i++) {
+		if (bfpi_version == 0x03 || sensor_mask & BIT(i)) {
+			err = device_create_file(&pdev->dev, &attr[2 * i].dev_attr);
+			if (err)
+				break;
+			err = device_create_file(&pdev->dev, &attr[2 * i + 1].dev_attr);
+			if (err)
+				break;
+		}
+	}
+
+	return err;
+}
+
+static int
+aaeon_hwmon_create_sysfs_files(struct platform_device *pdev, struct aaeon_hwmon_data *data)
+{
+	int err;
+
+	/* register sysfs interface files */
+	err = device_create_file(&pdev->dev, &dev_attr_name);
+	if (err)
+		return err;
+
+	/* registe sysfs to dump sensors BFPI version */
+	err = device_create_file(&pdev->dev, &info_sys_nodes_atts[0].dev_attr);
+	if (err)
+		return err;
+
+	/* create temperature name and value node */
+	err = aaeon_hwmon_create_sub_sysfs_fs(pdev, temp_sys_nodes_atts,
+				data->sensors_number[SENSOR_TEMP_NUMBER],
+				data->temp_bitmap, data->bfpi_version);
+	if (err)
+		return err;
+
+	/* create fan name and value node */
+	err = aaeon_hwmon_create_sub_sysfs_fs(pdev, fan_sys_nodes_atts,
+				data->sensors_number[SENSOR_FAN_NUMBER],
+				data->fan_bitmap, data->bfpi_version);
+	if (err)
+		return err;
+
+	/* create voltage name and value node */
+	err = aaeon_hwmon_create_sub_sysfs_fs(pdev, voltage_sys_nodes_atts,
+				data->sensors_number[SENSOR_VOLTAGE_NUMBER],
+				data->voltage_bitmap, data->bfpi_version);
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static void aaeon_hwmon_remove_sub_sysfs_fs(struct platform_device *pdev,
+					struct sensor_device_attribute_2 *attr,
+					int sensor_number,
+					u32 sensor_mask,
+					int bfpi_version)
+{
+	int i;
+
+	for (i = 0; i < sensor_number; i++) {
+		if (bfpi_version == 0x03 || sensor_mask & BIT(i)) {
+			device_remove_file(&pdev->dev, &attr[2 * i].dev_attr);
+			device_remove_file(&pdev->dev, &attr[2 * i + 1].dev_attr);
+		}
+	}
+}
+
+static void
+aaeon_hwmon_remove_sysfs_files(struct platform_device *pdev,
+			       struct aaeon_hwmon_data *data)
+{
+	/* degister sysfs interface files */
+	device_remove_file(&pdev->dev, &dev_attr_name);
+
+	/* degiste sysfs to dump sensors BFPI version */
+	device_remove_file(&pdev->dev, &info_sys_nodes_atts[0].dev_attr);
+
+	/* remove temperature name and value node */
+	aaeon_hwmon_remove_sub_sysfs_fs(pdev, temp_sys_nodes_atts,
+				data->sensors_number[SENSOR_TEMP_NUMBER],
+				data->temp_bitmap,
+				data->bfpi_version);
+
+	/* remove fan name and value node */
+	aaeon_hwmon_remove_sub_sysfs_fs(pdev, fan_sys_nodes_atts,
+				data->sensors_number[SENSOR_FAN_NUMBER],
+				data->fan_bitmap,
+				data->bfpi_version);
+
+	/* remove voltage name and value node */
+	aaeon_hwmon_remove_sub_sysfs_fs(pdev, voltage_sys_nodes_atts,
+				data->sensors_number[SENSOR_VOLTAGE_NUMBER],
+				data->voltage_bitmap,
+				data->bfpi_version);
+}
+
+static int aaeon_hwmon_remove(struct platform_device *pdev)
+{
+	struct aaeon_hwmon_data *data = platform_get_drvdata(pdev);
+
+	if (data->hwmon_dev)
+		hwmon_device_unregister(data->hwmon_dev);
+
+	aaeon_hwmon_remove_sysfs_files(pdev, data);
+
+	return 0;
+}
+
+static int aaeon_get_version(void)
+{
+	int err, retval;
+	u32 dev_id = 0x00;
+
+	err = asus_wmi_evaluate_method(AAEON_VERSION_METHOD_ID, dev_id, 0,
+				       &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static int aaeon_hwmon_init_drv_data(struct aaeon_hwmon_data *data)
+{
+	int err;
+
+	data->bfpi_version = aaeon_get_version();
+	if (data->bfpi_version < 0) {
+		pr_debug("Error BFPI verion\n");
+		return -1;
+	}
+
+	if (data->bfpi_version == 0x03) {
+		/* set the number of bits in temp bitmap */
+		data->sensors_number[SENSOR_TEMP_NUMBER] =
+				ARRAY_SIZE(temp_sensors_name_table_V3);
+		data->temp_names = temp_sensors_name_table_V3;
+
+		/* set the number of bits in fan bitmap */
+		data->sensors_number[SENSOR_FAN_NUMBER] =
+				ARRAY_SIZE(fan_sensors_name_table_V3);
+		data->fan_names = fan_sensors_name_table_V3;
+
+		/* set the number of bits in voltage bitmap */
+		data->sensors_number[SENSOR_VOLTAGE_NUMBER] =
+				ARRAY_SIZE(voltage_sensors_name_table_V3);
+		data->voltage_names = voltage_sensors_name_table_V3;
+	} else {
+		/* set the number of bits in temp bitmap */
+		data->sensors_number[SENSOR_TEMP_NUMBER] =
+				ARRAY_SIZE(temp_sensors_name_table);
+		data->temp_names = temp_sensors_name_table;
+
+		/* set the number of bits in fan bitmap */
+		data->sensors_number[SENSOR_FAN_NUMBER] =
+				ARRAY_SIZE(fan_sensors_name_table);
+		data->fan_names = fan_sensors_name_table;
+
+		/* set the number of bits in voltage bitmap */
+		data->sensors_number[SENSOR_VOLTAGE_NUMBER] =
+				ARRAY_SIZE(voltage_sensors_name_table);
+		data->voltage_names = voltage_sensors_name_table;
+	}
+
+	/* get temp supported bitmap */
+	err = asus_wmi_evaluate_method(HWM_INFORMATION_METHOD_ID,
+				BITMAP_TEMP_ARG, 0, &data->temp_bitmap);
+	if (err)
+		return err;
+
+	/* get fan supported bitmap */
+	err = asus_wmi_evaluate_method(HWM_INFORMATION_METHOD_ID,
+				BITMAP_FAN_ARG, 0, &data->fan_bitmap);
+	if (err)
+		return err;
+
+	/* get voltage supported bitmap */
+	err = asus_wmi_evaluate_method(HWM_INFORMATION_METHOD_ID,
+				BITMAP_VOLTAGE_ARG, 0, &data->voltage_bitmap);
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static int aaeon_hwmon_probe(struct platform_device *pdev)
+{
+	int err;
+	struct aaeon_hwmon_data *data;
+
+	pr_debug("aaeon hwomon device probe (support V3)!\n");
+	if (!wmi_has_guid(AAEON_WMI_MGMT_GUID)) {
+		pr_info("AAEON Management GUID not found\n");
+		return -ENODEV;
+	}
+
+	data = devm_kzalloc(&pdev->dev, sizeof(struct aaeon_hwmon_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	err = aaeon_hwmon_init_drv_data(data);
+	if (err) {
+		pr_info("Error to get sensor support bitmap\n");
+		goto exit;
+	}
+
+	if (data->bfpi_version != 0x03 && data->temp_bitmap == 0 &&
+		data->fan_bitmap == 0 && data->voltage_bitmap == 0) {
+		pr_debug("No sensors found\n");
+		err = -ENODEV;
+		goto exit;
+	}
+
+	platform_set_drvdata(pdev, data);
+	err = aaeon_hwmon_create_sysfs_files(pdev, data);
+	if (err)
+		goto exit;
+
+	data->hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev,
+							  "AAEON_HWM",
+							  data,
+							  NULL,
+							  NULL);
+	if (IS_ERR(data->hwmon_dev)) {
+		err = PTR_ERR(data->hwmon_dev);
+		data->hwmon_dev = NULL;
+		goto exit_unregister_sysfs;
+	}
+
+	return 0;
+
+exit_unregister_sysfs:
+	aaeon_hwmon_remove(pdev);
+exit:
+	return err;
+}
+
+static struct platform_driver aaeon_hwmon_driver = {
+	.driver = {
+		.name = DRVNAME,
+		.owner = THIS_MODULE,
+	},
+	.probe = aaeon_hwmon_probe,
+	.remove = aaeon_hwmon_remove,
+};
+
+module_platform_driver_probe(aaeon_hwmon_driver, aaeon_hwmon_probe);
+
+MODULE_ALIAS("platform:hwmon-aaeon");
+MODULE_DESCRIPTION("AAEON Hardware Monitoring Driver");
+MODULE_AUTHOR("Edward Lin <edward1_lin@aaeon.com.tw>");
+MODULE_AUTHOR("Kunyang Fan <kunyang_fan@aaeon.com.tw>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/hwmon.c
@@ -214,12 +214,14 @@
 
 	tzd = devm_thermal_zone_of_sensor_register(dev, index, tdata,
 						   &hwmon_thermal_ops);
-	/*
-	 * If CONFIG_THERMAL_OF is disabled, this returns -ENODEV,
-	 * so ignore that error but forward any other error.
-	 */
-	if (IS_ERR(tzd) && (PTR_ERR(tzd) != -ENODEV))
-		return PTR_ERR(tzd);
+	if (IS_ERR(tzd)) {
+		if (PTR_ERR(tzd) != -ENODEV)
+			return PTR_ERR(tzd);
+		dev_info(dev, "temp%d_input not attached to any thermal zone\n",
+			 index + 1);
+		devm_kfree(dev, tdata);
+		return 0;
+	}
 
 	err = devm_add_action(dev, hwmon_thermal_remove_sensor, &tdata->node);
 	if (err)
@@ -734,6 +736,7 @@
 {
 	struct hwmon_device *hwdev;
 	struct device *hdev;
+	struct device *tdev = dev;
 	int i, err, id;
 
 	/* Complain about invalid characters in hwmon name attribute */
@@ -791,17 +794,21 @@
 	hwdev->name = name;
 	hdev->class = &hwmon_class;
 	hdev->parent = dev;
-	hdev->of_node = dev ? dev->of_node : NULL;
+	while (tdev && !tdev->of_node)
+		tdev = tdev->parent;
+	hdev->of_node = tdev ? tdev->of_node : NULL;
 	hwdev->chip = chip;
 	dev_set_drvdata(hdev, drvdata);
 	dev_set_name(hdev, HWMON_ID_FORMAT, id);
 	err = device_register(hdev);
-	if (err)
-		goto free_hwmon;
+	if (err) {
+		put_device(hdev);
+		goto ida_remove;
+	}
 
 	INIT_LIST_HEAD(&hwdev->tzdata);
 
-	if (dev && dev->of_node && chip && chip->ops->read &&
+	if (hdev->of_node && chip && chip->ops->read &&
 	    chip->info[0]->type == hwmon_chip &&
 	    (chip->info[0]->config[0] & HWMON_C_REGISTER_TZ)) {
 		err = hwmon_thermal_register_sensors(hdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/i5500_temp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/i5500_temp.c
@@ -108,7 +108,7 @@
 	u32 tstimer;
 	s8 tsfsc;
 
-	err = pci_enable_device(pdev);
+	err = pcim_enable_device(pdev);
 	if (err) {
 		dev_err(&pdev->dev, "Failed to enable device\n");
 		return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ibmaem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ibmaem.c
@@ -550,7 +550,7 @@
 
 	res = platform_device_add(data->pdev);
 	if (res)
-		goto ipmi_err;
+		goto dev_add_err;
 
 	platform_set_drvdata(data->pdev, data);
 
@@ -598,7 +598,9 @@
 	ipmi_destroy_user(data->ipmi.user);
 ipmi_err:
 	platform_set_drvdata(data->pdev, NULL);
-	platform_device_unregister(data->pdev);
+	platform_device_del(data->pdev);
+dev_add_err:
+	platform_device_put(data->pdev);
 dev_err:
 	ida_simple_remove(&aem_ida, data->id);
 id_err:
@@ -690,7 +692,7 @@
 
 	res = platform_device_add(data->pdev);
 	if (res)
-		goto ipmi_err;
+		goto dev_add_err;
 
 	platform_set_drvdata(data->pdev, data);
 
@@ -738,7 +740,9 @@
 	ipmi_destroy_user(data->ipmi.user);
 ipmi_err:
 	platform_set_drvdata(data->pdev, NULL);
-	platform_device_unregister(data->pdev);
+	platform_device_del(data->pdev);
+dev_add_err:
+	platform_device_put(data->pdev);
 dev_err:
 	ida_simple_remove(&aem_ida, data->id);
 id_err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ibmpex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ibmpex.c
@@ -502,6 +502,7 @@
 	return;
 
 out_register:
+	list_del(&data->list);
 	hwmon_device_unregister(data->hwmon_dev);
 out_user:
 	ipmi_destroy_user(data->user);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ina3221.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ina3221.c
@@ -228,7 +228,7 @@
 	 * Shunt Voltage Sum register has 14-bit value with 1-bit shift
 	 * Other Shunt Voltage registers have 12 bits with 3-bit shift
 	 */
-	if (reg == INA3221_SHUNT_SUM)
+	if (reg == INA3221_SHUNT_SUM || reg == INA3221_CRIT_SUM)
 		*val = sign_extend32(regval >> 1, 14);
 	else
 		*val = sign_extend32(regval >> 3, 12);
@@ -465,7 +465,7 @@
 	 *     SHUNT_SUM: (1 / 40uV) << 1 = 1 / 20uV
 	 *     SHUNT[1-3]: (1 / 40uV) << 3 = 1 / 5uV
 	 */
-	if (reg == INA3221_SHUNT_SUM)
+	if (reg == INA3221_SHUNT_SUM || reg == INA3221_CRIT_SUM)
 		regval = DIV_ROUND_CLOSEST(voltage_uv, 20) & 0xfffe;
 	else
 		regval = DIV_ROUND_CLOSEST(voltage_uv, 5) & 0xfff8;
@@ -772,7 +772,7 @@
 		return ret;
 	} else if (val > INA3221_CHANNEL3) {
 		dev_err(dev, "invalid reg %d of %pOFn\n", val, child);
-		return ret;
+		return -EINVAL;
 	}
 
 	input = &ina->inputs[val];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/it87.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/it87.c
@@ -486,6 +486,8 @@
 #define has_pwm_freq2(data)	((data)->features & FEAT_PWM_FREQ2)
 #define has_six_temp(data)	((data)->features & FEAT_SIX_TEMP)
 #define has_vin3_5v(data)	((data)->features & FEAT_VIN3_5V)
+#define has_scaling(data)	((data)->features & (FEAT_12MV_ADC | \
+						     FEAT_10_9MV_ADC))
 
 struct it87_sio_data {
 	int sioaddr;
@@ -3098,7 +3100,7 @@
 			 "Detected broken BIOS defaults, disabling PWM interface\n");
 
 	/* Starting with IT8721F, we handle scaling of internal voltages */
-	if (has_12mv_adc(data)) {
+	if (has_scaling(data)) {
 		if (sio_data->internal & BIT(0))
 			data->in_scaled |= BIT(3);	/* in3 is AVCC */
 		if (sio_data->internal & BIT(1))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/jc42.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/jc42.c
@@ -19,6 +19,7 @@
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/regmap.h>
 
 /* Addresses to scan */
 static const unsigned short normal_i2c[] = {
@@ -189,31 +190,14 @@
 	{ STM_MANID, STTS3000_DEVID, STTS3000_DEVID_MASK },
 };
 
-enum temp_index {
-	t_input = 0,
-	t_crit,
-	t_min,
-	t_max,
-	t_num_temp
-};
-
-static const u8 temp_regs[t_num_temp] = {
-	[t_input] = JC42_REG_TEMP,
-	[t_crit] = JC42_REG_TEMP_CRITICAL,
-	[t_min] = JC42_REG_TEMP_LOWER,
-	[t_max] = JC42_REG_TEMP_UPPER,
-};
-
 /* Each client has this additional data */
 struct jc42_data {
-	struct i2c_client *client;
 	struct mutex	update_lock;	/* protect register access */
+	struct regmap	*regmap;
 	bool		extended;	/* true if extended range supported */
 	bool		valid;
-	unsigned long	last_updated;	/* In jiffies */
 	u16		orig_config;	/* original configuration */
 	u16		config;		/* current configuration */
-	u16		temp[t_num_temp];/* Temperatures */
 };
 
 #define JC42_TEMP_MIN_EXTENDED	(-40000)
@@ -238,85 +222,102 @@
 	return reg * 125 / 2;
 }
 
-static struct jc42_data *jc42_update_device(struct device *dev)
-{
-	struct jc42_data *data = dev_get_drvdata(dev);
-	struct i2c_client *client = data->client;
-	struct jc42_data *ret = data;
-	int i, val;
-
-	mutex_lock(&data->update_lock);
-
-	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
-		for (i = 0; i < t_num_temp; i++) {
-			val = i2c_smbus_read_word_swapped(client, temp_regs[i]);
-			if (val < 0) {
-				ret = ERR_PTR(val);
-				goto abort;
-			}
-			data->temp[i] = val;
-		}
-		data->last_updated = jiffies;
-		data->valid = true;
-	}
-abort:
-	mutex_unlock(&data->update_lock);
-	return ret;
-}
-
 static int jc42_read(struct device *dev, enum hwmon_sensor_types type,
 		     u32 attr, int channel, long *val)
 {
-	struct jc42_data *data = jc42_update_device(dev);
-	int temp, hyst;
+	struct jc42_data *data = dev_get_drvdata(dev);
+	unsigned int regval;
+	int ret, temp, hyst;
 
-	if (IS_ERR(data))
-		return PTR_ERR(data);
+	mutex_lock(&data->update_lock);
 
 	switch (attr) {
 	case hwmon_temp_input:
-		*val = jc42_temp_from_reg(data->temp[t_input]);
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP, &regval);
+		if (ret)
+			break;
+
+		*val = jc42_temp_from_reg(regval);
+		break;
 	case hwmon_temp_min:
-		*val = jc42_temp_from_reg(data->temp[t_min]);
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP_LOWER, &regval);
+		if (ret)
+			break;
+
+		*val = jc42_temp_from_reg(regval);
+		break;
 	case hwmon_temp_max:
-		*val = jc42_temp_from_reg(data->temp[t_max]);
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP_UPPER, &regval);
+		if (ret)
+			break;
+
+		*val = jc42_temp_from_reg(regval);
+		break;
 	case hwmon_temp_crit:
-		*val = jc42_temp_from_reg(data->temp[t_crit]);
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP_CRITICAL,
+				  &regval);
+		if (ret)
+			break;
+
+		*val = jc42_temp_from_reg(regval);
+		break;
 	case hwmon_temp_max_hyst:
-		temp = jc42_temp_from_reg(data->temp[t_max]);
+		ret = regmap_read(data->regmap, JC42_REG_TEMP_UPPER, &regval);
+		if (ret)
+			break;
+
+		temp = jc42_temp_from_reg(regval);
 		hyst = jc42_hysteresis[(data->config & JC42_CFG_HYST_MASK)
 						>> JC42_CFG_HYST_SHIFT];
 		*val = temp - hyst;
-		return 0;
+		break;
 	case hwmon_temp_crit_hyst:
-		temp = jc42_temp_from_reg(data->temp[t_crit]);
+		ret = regmap_read(data->regmap, JC42_REG_TEMP_CRITICAL,
+				  &regval);
+		if (ret)
+			break;
+
+		temp = jc42_temp_from_reg(regval);
 		hyst = jc42_hysteresis[(data->config & JC42_CFG_HYST_MASK)
 						>> JC42_CFG_HYST_SHIFT];
 		*val = temp - hyst;
-		return 0;
+		break;
 	case hwmon_temp_min_alarm:
-		*val = (data->temp[t_input] >> JC42_ALARM_MIN_BIT) & 1;
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP, &regval);
+		if (ret)
+			break;
+
+		*val = (regval >> JC42_ALARM_MIN_BIT) & 1;
+		break;
 	case hwmon_temp_max_alarm:
-		*val = (data->temp[t_input] >> JC42_ALARM_MAX_BIT) & 1;
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP, &regval);
+		if (ret)
+			break;
+
+		*val = (regval >> JC42_ALARM_MAX_BIT) & 1;
+		break;
 	case hwmon_temp_crit_alarm:
-		*val = (data->temp[t_input] >> JC42_ALARM_CRIT_BIT) & 1;
-		return 0;
+		ret = regmap_read(data->regmap, JC42_REG_TEMP, &regval);
+		if (ret)
+			break;
+
+		*val = (regval >> JC42_ALARM_CRIT_BIT) & 1;
+		break;
 	default:
-		return -EOPNOTSUPP;
+		ret = -EOPNOTSUPP;
+		break;
 	}
+
+	mutex_unlock(&data->update_lock);
+
+	return ret;
 }
 
 static int jc42_write(struct device *dev, enum hwmon_sensor_types type,
 		      u32 attr, int channel, long val)
 {
 	struct jc42_data *data = dev_get_drvdata(dev);
-	struct i2c_client *client = data->client;
+	unsigned int regval;
 	int diff, hyst;
 	int ret;
 
@@ -324,21 +325,23 @@
 
 	switch (attr) {
 	case hwmon_temp_min:
-		data->temp[t_min] = jc42_temp_to_reg(val, data->extended);
-		ret = i2c_smbus_write_word_swapped(client, temp_regs[t_min],
-						   data->temp[t_min]);
+		ret = regmap_write(data->regmap, JC42_REG_TEMP_LOWER,
+				   jc42_temp_to_reg(val, data->extended));
 		break;
 	case hwmon_temp_max:
-		data->temp[t_max] = jc42_temp_to_reg(val, data->extended);
-		ret = i2c_smbus_write_word_swapped(client, temp_regs[t_max],
-						   data->temp[t_max]);
+		ret = regmap_write(data->regmap, JC42_REG_TEMP_UPPER,
+				   jc42_temp_to_reg(val, data->extended));
 		break;
 	case hwmon_temp_crit:
-		data->temp[t_crit] = jc42_temp_to_reg(val, data->extended);
-		ret = i2c_smbus_write_word_swapped(client, temp_regs[t_crit],
-						   data->temp[t_crit]);
+		ret = regmap_write(data->regmap, JC42_REG_TEMP_CRITICAL,
+				   jc42_temp_to_reg(val, data->extended));
 		break;
 	case hwmon_temp_crit_hyst:
+		ret = regmap_read(data->regmap, JC42_REG_TEMP_CRITICAL,
+				  &regval);
+		if (ret)
+			break;
+
 		/*
 		 * JC42.4 compliant chips only support four hysteresis values.
 		 * Pick best choice and go from there.
@@ -346,7 +349,7 @@
 		val = clamp_val(val, (data->extended ? JC42_TEMP_MIN_EXTENDED
 						     : JC42_TEMP_MIN) - 6000,
 				JC42_TEMP_MAX);
-		diff = jc42_temp_from_reg(data->temp[t_crit]) - val;
+		diff = jc42_temp_from_reg(regval) - val;
 		hyst = 0;
 		if (diff > 0) {
 			if (diff < 2250)
@@ -358,9 +361,8 @@
 		}
 		data->config = (data->config & ~JC42_CFG_HYST_MASK) |
 				(hyst << JC42_CFG_HYST_SHIFT);
-		ret = i2c_smbus_write_word_swapped(data->client,
-						   JC42_REG_CONFIG,
-						   data->config);
+		ret = regmap_write(data->regmap, JC42_REG_CONFIG,
+				   data->config);
 		break;
 	default:
 		ret = -EOPNOTSUPP;
@@ -458,51 +460,80 @@
 	.info = jc42_info,
 };
 
+static bool jc42_readable_reg(struct device *dev, unsigned int reg)
+{
+	return (reg >= JC42_REG_CAP && reg <= JC42_REG_DEVICEID) ||
+		reg == JC42_REG_SMBUS;
+}
+
+static bool jc42_writable_reg(struct device *dev, unsigned int reg)
+{
+	return (reg >= JC42_REG_CONFIG && reg <= JC42_REG_TEMP_CRITICAL) ||
+		reg == JC42_REG_SMBUS;
+}
+
+static bool jc42_volatile_reg(struct device *dev, unsigned int reg)
+{
+	return reg == JC42_REG_CONFIG || reg == JC42_REG_TEMP;
+}
+
+static const struct regmap_config jc42_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+	.val_format_endian = REGMAP_ENDIAN_BIG,
+	.max_register = JC42_REG_SMBUS,
+	.writeable_reg = jc42_writable_reg,
+	.readable_reg = jc42_readable_reg,
+	.volatile_reg = jc42_volatile_reg,
+	.cache_type = REGCACHE_RBTREE,
+};
+
 static int jc42_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
 	struct device *hwmon_dev;
+	unsigned int config, cap;
 	struct jc42_data *data;
-	int config, cap;
+	int ret;
 
 	data = devm_kzalloc(dev, sizeof(struct jc42_data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
-	data->client = client;
+	data->regmap = devm_regmap_init_i2c(client, &jc42_regmap_config);
+	if (IS_ERR(data->regmap))
+		return PTR_ERR(data->regmap);
+
 	i2c_set_clientdata(client, data);
 	mutex_init(&data->update_lock);
 
-	cap = i2c_smbus_read_word_swapped(client, JC42_REG_CAP);
-	if (cap < 0)
-		return cap;
+	ret = regmap_read(data->regmap, JC42_REG_CAP, &cap);
+	if (ret)
+		return ret;
 
 	data->extended = !!(cap & JC42_CAP_RANGE);
 
 	if (device_property_read_bool(dev, "smbus-timeout-disable")) {
-		int smbus;
-
 		/*
 		 * Not all chips support this register, but from a
 		 * quick read of various datasheets no chip appears
 		 * incompatible with the below attempt to disable
 		 * the timeout. And the whole thing is opt-in...
 		 */
-		smbus = i2c_smbus_read_word_swapped(client, JC42_REG_SMBUS);
-		if (smbus < 0)
-			return smbus;
-		i2c_smbus_write_word_swapped(client, JC42_REG_SMBUS,
-					     smbus | SMBUS_STMOUT);
+		ret = regmap_set_bits(data->regmap, JC42_REG_SMBUS,
+				      SMBUS_STMOUT);
+		if (ret)
+			return ret;
 	}
 
-	config = i2c_smbus_read_word_swapped(client, JC42_REG_CONFIG);
-	if (config < 0)
-		return config;
+	ret = regmap_read(data->regmap, JC42_REG_CONFIG, &config);
+	if (ret)
+		return ret;
 
 	data->orig_config = config;
 	if (config & JC42_CFG_SHUTDOWN) {
 		config &= ~JC42_CFG_SHUTDOWN;
-		i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, config);
+		regmap_write(data->regmap, JC42_REG_CONFIG, config);
 	}
 	data->config = config;
 
@@ -523,7 +554,7 @@
 
 		config = (data->orig_config & ~JC42_CFG_HYST_MASK)
 		  | (data->config & JC42_CFG_HYST_MASK);
-		i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, config);
+		regmap_write(data->regmap, JC42_REG_CONFIG, config);
 	}
 	return 0;
 }
@@ -535,8 +566,11 @@
 	struct jc42_data *data = dev_get_drvdata(dev);
 
 	data->config |= JC42_CFG_SHUTDOWN;
-	i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG,
-				     data->config);
+	regmap_write(data->regmap, JC42_REG_CONFIG, data->config);
+
+	regcache_cache_only(data->regmap, true);
+	regcache_mark_dirty(data->regmap);
+
 	return 0;
 }
 
@@ -544,10 +578,13 @@
 {
 	struct jc42_data *data = dev_get_drvdata(dev);
 
+	regcache_cache_only(data->regmap, false);
+
 	data->config &= ~JC42_CFG_SHUTDOWN;
-	i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG,
-				     data->config);
-	return 0;
+	regmap_write(data->regmap, JC42_REG_CONFIG, data->config);
+
+	/* Restore cached register values to hardware */
+	return regcache_sync(data->regmap);
 }
 
 static const struct dev_pm_ops jc42_dev_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/k10temp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/k10temp.c
@@ -75,26 +75,14 @@
 
 #define ZEN_CUR_TEMP_SHIFT			21
 #define ZEN_CUR_TEMP_RANGE_SEL_MASK		BIT(19)
+#define ZEN_CUR_TEMP_TJ_SEL_MASK		GENMASK(17, 16)
 
-#define ZEN_SVI_BASE				0x0005A000
-
-/* F17h thermal registers through SMN */
-#define F17H_M01H_SVI_TEL_PLANE0		(ZEN_SVI_BASE + 0xc)
-#define F17H_M01H_SVI_TEL_PLANE1		(ZEN_SVI_BASE + 0x10)
-#define F17H_M31H_SVI_TEL_PLANE0		(ZEN_SVI_BASE + 0x14)
-#define F17H_M31H_SVI_TEL_PLANE1		(ZEN_SVI_BASE + 0x10)
-
-#define F17H_M01H_CFACTOR_ICORE			1000000	/* 1A / LSB	*/
-#define F17H_M01H_CFACTOR_ISOC			250000	/* 0.25A / LSB	*/
-#define F17H_M31H_CFACTOR_ICORE			1000000	/* 1A / LSB	*/
-#define F17H_M31H_CFACTOR_ISOC			310000	/* 0.31A / LSB	*/
-
-/* F19h thermal registers through SMN */
-#define F19H_M01_SVI_TEL_PLANE0			(ZEN_SVI_BASE + 0x14)
-#define F19H_M01_SVI_TEL_PLANE1			(ZEN_SVI_BASE + 0x10)
-
-#define F19H_M01H_CFACTOR_ICORE			1000000	/* 1A / LSB	*/
-#define F19H_M01H_CFACTOR_ISOC			310000	/* 0.31A / LSB	*/
+/*
+ * AMD's Industrial processor 3255 supports temperature from -40 deg to 105 deg Celsius.
+ * Use the model name to identify 3255 CPUs and set a flag to display negative temperature.
+ * Do not round off to zero for negative Tctl or Tdie values if the flag is set
+ */
+#define AMD_I3255_STR				"3255"
 
 struct k10temp_data {
 	struct pci_dev *pdev;
@@ -105,6 +93,7 @@
 	u32 show_temp;
 	bool is_zen;
 	u32 ccd_offset;
+	bool disp_negative;
 };
 
 #define TCTL_BIT	0
@@ -175,7 +164,8 @@
 
 	data->read_tempreg(data->pdev, &regval);
 	temp = (regval >> ZEN_CUR_TEMP_SHIFT) * 125;
-	if (regval & data->temp_adjust_mask)
+	if ((regval & data->temp_adjust_mask) ||
+	    (regval & ZEN_CUR_TEMP_TJ_SEL_MASK) == ZEN_CUR_TEMP_TJ_SEL_MASK)
 		temp -= 49000;
 	return temp;
 }
@@ -191,6 +181,10 @@
 	"Tccd6",
 	"Tccd7",
 	"Tccd8",
+	"Tccd9",
+	"Tccd10",
+	"Tccd11",
+	"Tccd12",
 };
 
 static int k10temp_read_labels(struct device *dev,
@@ -218,15 +212,15 @@
 		switch (channel) {
 		case 0:		/* Tctl */
 			*val = get_raw_temp(data);
-			if (*val < 0)
+			if (*val < 0 && !data->disp_negative)
 				*val = 0;
 			break;
 		case 1:		/* Tdie */
 			*val = get_raw_temp(data) - data->temp_offset;
-			if (*val < 0)
+			if (*val < 0 && !data->disp_negative)
 				*val = 0;
 			break;
-		case 2 ... 9:		/* Tccd{1-8} */
+		case 2 ... 13:		/* Tccd{1-12} */
 			amd_smn_read(amd_pci_dev_to_node_id(data->pdev),
 				     ZEN_CCD_TEMP(data->ccd_offset, channel - 2),
 						  &regval);
@@ -361,6 +355,10 @@
 			   HWMON_T_INPUT | HWMON_T_LABEL,
 			   HWMON_T_INPUT | HWMON_T_LABEL,
 			   HWMON_T_INPUT | HWMON_T_LABEL,
+			   HWMON_T_INPUT | HWMON_T_LABEL,
+			   HWMON_T_INPUT | HWMON_T_LABEL,
+			   HWMON_T_INPUT | HWMON_T_LABEL,
+			   HWMON_T_INPUT | HWMON_T_LABEL,
 			   HWMON_T_INPUT | HWMON_T_LABEL),
 	NULL
 };
@@ -415,6 +413,11 @@
 	data->pdev = pdev;
 	data->show_temp |= BIT(TCTL_BIT);	/* Always show Tctl */
 
+	if (boot_cpu_data.x86 == 0x17 &&
+	    strstr(boot_cpu_data.x86_model_id, AMD_I3255_STR)) {
+		data->disp_negative = true;
+	}
+
 	if (boot_cpu_data.x86 == 0x15 &&
 	    ((boot_cpu_data.x86_model & 0xf0) == 0x60 ||
 	     (boot_cpu_data.x86_model & 0xf0) == 0x70)) {
@@ -457,6 +460,11 @@
 			data->ccd_offset = 0x300;
 			k10temp_get_ccd_support(pdev, data, 8);
 			break;
+		case 0x10 ... 0x1f:
+		case 0xa0 ... 0xaf:
+			data->ccd_offset = 0x300;
+			k10temp_get_ccd_support(pdev, data, 12);
+			break;
 		}
 	} else {
 		data->read_htcreg = read_htcreg_pci;
@@ -497,6 +505,7 @@
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_17H_M60H_DF_F3) },
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_17H_M70H_DF_F3) },
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_19H_DF_F3) },
+	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_19H_M10H_DF_F3) },
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_19H_M40H_DF_F3) },
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_19H_M50H_DF_F3) },
 	{ PCI_VDEVICE(HYGON, PCI_DEVICE_ID_AMD_17H_DF_F3) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/lm90.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/lm90.c
@@ -35,13 +35,14 @@
  * explicitly as max6659, or if its address is not 0x4c.
  * These chips lack the remote temperature offset feature.
  *
- * This driver also supports the MAX6654 chip made by Maxim. This chip can
- * be at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is
- * otherwise similar to MAX6657/MAX6658/MAX6659. Extended range is available
- * by setting the configuration register accordingly, and is done during
- * initialization. Extended precision is only available at conversion rates
- * of 1 Hz and slower. Note that extended precision is not enabled by
- * default, as this driver initializes all chips to 2 Hz by design.
+ * This driver also supports the MAX6654 chip made by Maxim. This chip can be
+ * at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is similar
+ * to MAX6657/MAX6658/MAX6659, but does not support critical temperature
+ * limits. Extended range is available by setting the configuration register
+ * accordingly, and is done during initialization. Extended precision is only
+ * available at conversion rates of 1 Hz and slower. Note that extended
+ * precision is not enabled by default, as this driver initializes all chips
+ * to 2 Hz by design.
  *
  * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
  * MAX6692 chips made by Maxim.  These are again similar to the LM86,
@@ -69,10 +70,10 @@
  * This driver also supports the G781 from GMT. This device is compatible
  * with the ADM1032.
  *
- * This driver also supports TMP451 from Texas Instruments. This device is
- * supported in both compatibility and extended mode. It's mostly compatible
- * with ADT7461 except for local temperature low byte register and max
- * conversion rate.
+ * This driver also supports TMP451 and TMP461 from Texas Instruments.
+ * Those devices are supported in both compatibility and extended mode.
+ * They are mostly compatible with ADT7461 except for local temperature
+ * low byte register and max conversion rate.
  *
  * Since the LM90 was the first chipset supported by this driver, most
  * comments will refer to this chipset, but are actually general and
@@ -112,7 +113,7 @@
 	0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
 
 enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
-	max6646, w83l771, max6696, sa56004, g781, tmp451, max6654 };
+	max6646, w83l771, max6696, sa56004, g781, tmp451, tmp461, max6654 };
 
 /*
  * The LM90 registers
@@ -168,8 +169,12 @@
 
 #define LM90_MAX_CONVRATE_MS	16000	/* Maximum conversion rate in ms */
 
-/* TMP451 registers */
+/* TMP451/TMP461 registers */
 #define TMP451_REG_R_LOCAL_TEMPL	0x15
+#define TMP451_REG_CONALERT		0x22
+
+#define TMP461_REG_CHEN			0x16
+#define TMP461_REG_DFC			0x24
 
 /*
  * Device flags
@@ -182,7 +187,10 @@
 #define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm		*/
 #define LM90_HAVE_TEMP3		(1 << 6) /* 3rd temperature sensor	*/
 #define LM90_HAVE_BROKEN_ALERT	(1 << 7) /* Broken alert		*/
-#define LM90_PAUSE_FOR_CONFIG	(1 << 8) /* Pause conversion for config	*/
+#define LM90_HAVE_EXTENDED_TEMP	(1 << 8) /* extended temperature support*/
+#define LM90_PAUSE_FOR_CONFIG	(1 << 9) /* Pause conversion for config	*/
+#define LM90_HAVE_CRIT		(1 << 10)/* Chip supports CRIT/OVERT register	*/
+#define LM90_HAVE_CRIT_ALRM_SWP	(1 << 11)/* critical alarm bits swapped	*/
 
 /* LM90 status */
 #define LM90_STATUS_LTHRM	(1 << 0) /* local THERM limit tripped */
@@ -192,6 +200,7 @@
 #define LM90_STATUS_RHIGH	(1 << 4) /* remote high temp limit tripped */
 #define LM90_STATUS_LLOW	(1 << 5) /* local low temp limit tripped */
 #define LM90_STATUS_LHIGH	(1 << 6) /* local high temp limit tripped */
+#define LM90_STATUS_BUSY	(1 << 7) /* conversion is ongoing */
 
 #define MAX6696_STATUS2_R2THRM	(1 << 1) /* remote2 THERM limit tripped */
 #define MAX6696_STATUS2_R2OPEN	(1 << 2) /* remote2 is an open circuit */
@@ -229,6 +238,7 @@
 	{ "w83l771", w83l771 },
 	{ "sa56004", sa56004 },
 	{ "tmp451", tmp451 },
+	{ "tmp461", tmp461 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, lm90_id);
@@ -326,6 +336,10 @@
 		.compatible = "ti,tmp451",
 		.data = (void *)tmp451
 	},
+	{
+		.compatible = "ti,tmp461",
+		.data = (void *)tmp461
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, lm90_of_match);
@@ -344,85 +358,99 @@
 static const struct lm90_params lm90_params[] = {
 	[adm1032] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 10,
 	},
 	[adt7461] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 10,
 	},
 	[g781] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
-		.max_convrate = 8,
+		.max_convrate = 7,
 	},
 	[lm86] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 	},
 	[lm90] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 	},
 	[lm99] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 	},
 	[max6646] = {
+		.flags = LM90_HAVE_CRIT | LM90_HAVE_BROKEN_ALERT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 6,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[max6654] = {
+		.flags = LM90_HAVE_BROKEN_ALERT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 7,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[max6657] = {
-		.flags = LM90_PAUSE_FOR_CONFIG,
+		.flags = LM90_PAUSE_FOR_CONFIG | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[max6659] = {
-		.flags = LM90_HAVE_EMERGENCY,
+		.flags = LM90_HAVE_EMERGENCY | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[max6680] = {
-		.flags = LM90_HAVE_OFFSET,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT
+		  | LM90_HAVE_CRIT_ALRM_SWP | LM90_HAVE_BROKEN_ALERT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 7,
 	},
 	[max6696] = {
 		.flags = LM90_HAVE_EMERGENCY
-		  | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3,
+		  | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3 | LM90_HAVE_CRIT,
 		.alert_alarms = 0x1c7c,
 		.max_convrate = 6,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[w83l771] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 	},
 	[sa56004] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 		.reg_local_ext = SA56004_REG_R_LOCAL_TEMPL,
 	},
 	[tmp451] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT,
+		.alert_alarms = 0x7c,
+		.max_convrate = 9,
+		.reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+	},
+	[tmp461] = {
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 9,
 		.reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
@@ -651,20 +679,22 @@
 	struct i2c_client *client = data->client;
 	int val;
 
-	val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
-	if (val < 0)
-		return val;
-	data->temp8[LOCAL_CRIT] = val;
+	if (data->flags & LM90_HAVE_CRIT) {
+		val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
+		if (val < 0)
+			return val;
+		data->temp8[LOCAL_CRIT] = val;
 
-	val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
-	if (val < 0)
-		return val;
-	data->temp8[REMOTE_CRIT] = val;
+		val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
+		if (val < 0)
+			return val;
+		data->temp8[REMOTE_CRIT] = val;
 
-	val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
-	if (val < 0)
-		return val;
-	data->temp_hyst = val;
+		val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
+		if (val < 0)
+			return val;
+		data->temp_hyst = val;
+	}
 
 	val = lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH);
 	if (val < 0)
@@ -792,7 +822,7 @@
 		val = lm90_read_reg(client, LM90_REG_R_STATUS);
 		if (val < 0)
 			return val;
-		data->alarms = val;	/* lower 8 bit of alarms */
+		data->alarms = val & ~LM90_STATUS_BUSY;
 
 		if (data->kind == max6696) {
 			val = lm90_select_remote_channel(data, 1);
@@ -819,7 +849,7 @@
 		 * Re-enable ALERT# output if it was originally enabled and
 		 * relevant alarms are all clear
 		 */
-		if (!(data->config_orig & 0x80) &&
+		if ((client->irq || !(data->config_orig & 0x80)) &&
 		    !(data->alarms & data->alert_alarms)) {
 			if (data->config & 0x80) {
 				dev_dbg(&client->dev, "Re-enabling ALERT#\n");
@@ -998,7 +1028,7 @@
 	s16 temp11 = data->temp11[index];
 	int temp;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u16_adt7461(data, temp11);
 	else if (data->kind == max6646)
 		temp = temp_from_u16(temp11);
@@ -1035,7 +1065,7 @@
 		val -= 16000;
 	}
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		data->temp11[index] = temp_to_u16_adt7461(data, val);
 	else if (data->kind == max6646)
 		data->temp11[index] = temp_to_u8(val) << 8;
@@ -1062,7 +1092,7 @@
 	s8 temp8 = data->temp8[index];
 	int temp;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u8_adt7461(data, temp8);
 	else if (data->kind == max6646)
 		temp = temp_from_u8(temp8);
@@ -1098,7 +1128,7 @@
 		val -= 16000;
 	}
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		data->temp8[index] = temp_to_u8_adt7461(data, val);
 	else if (data->kind == max6646)
 		data->temp8[index] = temp_to_u8(val);
@@ -1116,7 +1146,7 @@
 {
 	int temp;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u8_adt7461(data, data->temp8[index]);
 	else if (data->kind == max6646)
 		temp = temp_from_u8(data->temp8[index]);
@@ -1136,15 +1166,15 @@
 	int temp;
 	int err;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u8_adt7461(data, data->temp8[LOCAL_CRIT]);
 	else if (data->kind == max6646)
 		temp = temp_from_u8(data->temp8[LOCAL_CRIT]);
 	else
 		temp = temp_from_s8(data->temp8[LOCAL_CRIT]);
 
-	/* prevent integer underflow */
-	val = max(val, -128000l);
+	/* prevent integer overflow/underflow */
+	val = clamp_val(val, -128000l, 255000l);
 
 	data->temp_hyst = hyst_to_reg(temp - val);
 	err = i2c_smbus_write_byte_data(client, LM90_REG_W_TCRIT_HYST,
@@ -1175,6 +1205,7 @@
 static const u8 lm90_min_alarm_bits[3] = { 5, 3, 11 };
 static const u8 lm90_max_alarm_bits[3] = { 6, 4, 12 };
 static const u8 lm90_crit_alarm_bits[3] = { 0, 1, 9 };
+static const u8 lm90_crit_alarm_bits_swapped[3] = { 1, 0, 9 };
 static const u8 lm90_emergency_alarm_bits[3] = { 15, 13, 14 };
 static const u8 lm90_fault_bits[3] = { 0, 2, 10 };
 
@@ -1200,7 +1231,10 @@
 		*val = (data->alarms >> lm90_max_alarm_bits[channel]) & 1;
 		break;
 	case hwmon_temp_crit_alarm:
-		*val = (data->alarms >> lm90_crit_alarm_bits[channel]) & 1;
+		if (data->flags & LM90_HAVE_CRIT_ALRM_SWP)
+			*val = (data->alarms >> lm90_crit_alarm_bits_swapped[channel]) & 1;
+		else
+			*val = (data->alarms >> lm90_crit_alarm_bits[channel]) & 1;
 		break;
 	case hwmon_temp_emergency_alarm:
 		*val = (data->alarms >> lm90_emergency_alarm_bits[channel]) & 1;
@@ -1448,12 +1482,11 @@
 	if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0)
 		return -ENODEV;
 
-	if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) {
+	if (man_id == 0x01 || man_id == 0x5C || man_id == 0xA1) {
 		config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2);
 		if (config2 < 0)
 			return -ENODEV;
-	} else
-		config2 = 0;		/* Make compiler happy */
+	}
 
 	if ((address == 0x4C || address == 0x4D)
 	 && man_id == 0x01) { /* National Semiconductor */
@@ -1627,18 +1660,26 @@
 		 && convrate <= 0x08)
 			name = "g781";
 	} else
-	if (address == 0x4C
-	 && man_id == 0x55) { /* Texas Instruments */
-		int local_ext;
+	if (man_id == 0x55 && chip_id == 0x00 &&
+	    (config1 & 0x1B) == 0x00 && convrate <= 0x09) {
+		int local_ext, conalert, chen, dfc;
 
 		local_ext = i2c_smbus_read_byte_data(client,
 						     TMP451_REG_R_LOCAL_TEMPL);
-
-		if (chip_id == 0x00 /* TMP451 */
-		 && (config1 & 0x1B) == 0x00
-		 && convrate <= 0x09
-		 && (local_ext & 0x0F) == 0x00)
-			name = "tmp451";
+		conalert = i2c_smbus_read_byte_data(client,
+						    TMP451_REG_CONALERT);
+		chen = i2c_smbus_read_byte_data(client, TMP461_REG_CHEN);
+		dfc = i2c_smbus_read_byte_data(client, TMP461_REG_DFC);
+
+		if ((local_ext & 0x0F) == 0x00 &&
+		    (conalert & 0xf1) == 0x01 &&
+		    (chen & 0xfc) == 0x00 &&
+		    (dfc & 0xfc) == 0x00) {
+			if (address == 0x4c && !(chen & 0x03))
+				name = "tmp451";
+			else if (address >= 0x48 && address <= 0x4f)
+				name = "tmp461";
+		}
 	}
 
 	if (!name) { /* identification failed */
@@ -1685,7 +1726,7 @@
 	lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
 
 	/* Check Temperature Range Select */
-	if (data->kind == adt7461 || data->kind == tmp451) {
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP) {
 		if (config & 0x04)
 			data->flags |= LM90_FLAG_ADT7461_EXT;
 	}
@@ -1767,22 +1808,22 @@
 
 	if (st & LM90_STATUS_LLOW)
 		hwmon_notify_event(data->hwmon_dev, hwmon_temp,
-				   hwmon_temp_min, 0);
+				   hwmon_temp_min_alarm, 0);
 	if (st & LM90_STATUS_RLOW)
 		hwmon_notify_event(data->hwmon_dev, hwmon_temp,
-				   hwmon_temp_min, 1);
+				   hwmon_temp_min_alarm, 1);
 	if (st2 & MAX6696_STATUS2_R2LOW)
 		hwmon_notify_event(data->hwmon_dev, hwmon_temp,
-				   hwmon_temp_min, 2);
+				   hwmon_temp_min_alarm, 2);
 	if (st & LM90_STATUS_LHIGH)
 		hwmon_notify_event(data->hwmon_dev, hwmon_temp,
-				   hwmon_temp_max, 0);
+				   hwmon_temp_max_alarm, 0);
 	if (st & LM90_STATUS_RHIGH)
 		hwmon_notify_event(data->hwmon_dev, hwmon_temp,
-				   hwmon_temp_max, 1);
+				   hwmon_temp_max_alarm, 1);
 	if (st2 & MAX6696_STATUS2_R2HIGH)
 		hwmon_notify_event(data->hwmon_dev, hwmon_temp,
-				   hwmon_temp_max, 2);
+				   hwmon_temp_max_alarm, 2);
 
 	return true;
 }
@@ -1878,11 +1919,14 @@
 	info->config = data->channel_config;
 
 	data->channel_config[0] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
-		HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
-		HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM;
+		HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM;
 	data->channel_config[1] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
-		HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
-		HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM | HWMON_T_FAULT;
+		HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | HWMON_T_FAULT;
+
+	if (data->flags & LM90_HAVE_CRIT) {
+		data->channel_config[0] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
+		data->channel_config[1] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
+	}
 
 	if (data->flags & LM90_HAVE_OFFSET)
 		data->channel_config[1] |= HWMON_T_OFFSET;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/lm95234.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/lm95234.c
@@ -301,7 +301,8 @@
 	if (ret < 0)
 		return ret;
 
-	val = clamp_val(DIV_ROUND_CLOSEST(val, 1000), 0, index ? 255 : 127);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, 0, (index ? 255 : 127) * 1000),
+				1000);
 
 	mutex_lock(&data->update_lock);
 	data->tcrit2[index] = val;
@@ -350,7 +351,7 @@
 	if (ret < 0)
 		return ret;
 
-	val = clamp_val(DIV_ROUND_CLOSEST(val, 1000), 0, 255);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, 0, 255000), 1000);
 
 	mutex_lock(&data->update_lock);
 	data->tcrit1[index] = val;
@@ -391,7 +392,7 @@
 	if (ret < 0)
 		return ret;
 
-	val = DIV_ROUND_CLOSEST(val, 1000);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, -255000, 255000), 1000);
 	val = clamp_val((int)data->tcrit1[index] - val, 0, 31);
 
 	mutex_lock(&data->update_lock);
@@ -431,7 +432,7 @@
 		return ret;
 
 	/* Accuracy is 1/2 degrees C */
-	val = clamp_val(DIV_ROUND_CLOSEST(val, 500), -128, 127);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, -64000, 63500), 500);
 
 	mutex_lock(&data->update_lock);
 	data->toffset[index] = val;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ltc2945.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ltc2945.c
@@ -248,6 +248,8 @@
 
 	/* convert to register value, then clamp and write result */
 	regval = ltc2945_val_to_reg(dev, reg, val);
+	if (regval < 0)
+		return regval;
 	if (is_power_reg(reg)) {
 		regval = clamp_val(regval, 0, 0xffffff);
 		regbuf[0] = regval >> 16;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ltc2947-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ltc2947-core.c
@@ -396,7 +396,7 @@
 		return ret;
 
 	/* in milidegrees celcius, temp is given by: */
-	*val = (__val * 204) + 550;
+	*val = (__val * 204) + 5500;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ltc2992.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ltc2992.c
@@ -324,6 +324,7 @@
 	st->gc.label = name;
 	st->gc.parent = &st->client->dev;
 	st->gc.owner = THIS_MODULE;
+	st->gc.can_sleep = true;
 	st->gc.base = -1;
 	st->gc.names = st->gpio_names;
 	st->gc.ngpio = ARRAY_SIZE(st->gpio_names);
@@ -911,8 +912,14 @@
 		}
 
 		ret = fwnode_property_read_u32(child, "shunt-resistor-micro-ohms", &val);
-		if (!ret)
+		if (!ret) {
+			if (!val) {
+				fwnode_handle_put(child);
+				return dev_err_probe(&st->client->dev, -EINVAL,
+						     "shunt resistor value cannot be zero\n");
+			}
 			st->r_sense_uohm[addr] = val;
+		}
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/max16065.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/max16065.c
@@ -79,7 +79,7 @@
 };
 
 struct max16065_data {
-	enum chips type;
+	enum chips chip;
 	struct i2c_client *client;
 	const struct attribute_group *groups[4];
 	struct mutex update_lock;
@@ -114,9 +114,10 @@
 	return limit * range / 256;
 }
 
-static inline int MV_TO_LIMIT(int mv, int range)
+static inline int MV_TO_LIMIT(unsigned long mv, int range)
 {
-	return clamp_val(DIV_ROUND_CLOSEST(mv * 256, range), 0, 255);
+	mv = clamp_val(mv, 0, ULONG_MAX / 256);
+	return DIV_ROUND_CLOSEST(clamp_val(mv * 256, 0, range * 255), range);
 }
 
 static inline int ADC_TO_CURR(int adc, int gain)
@@ -161,10 +162,17 @@
 						     MAX16065_CURR_SENSE);
 		}
 
-		for (i = 0; i < DIV_ROUND_UP(data->num_adc, 8); i++)
+		for (i = 0; i < 2; i++)
 			data->fault[i]
 			  = i2c_smbus_read_byte_data(client, MAX16065_FAULT(i));
 
+		/*
+		 * MAX16067 and MAX16068 have separate undervoltage and
+		 * overvoltage alarm bits. Squash them together.
+		 */
+		if (data->chip == max16067 || data->chip == max16068)
+			data->fault[0] |= data->fault[1];
+
 		data->last_updated = jiffies;
 		data->valid = 1;
 	}
@@ -493,8 +501,6 @@
 	.is_visible = max16065_secondary_is_visible,
 };
 
-static const struct i2c_device_id max16065_id[];
-
 static int max16065_probe(struct i2c_client *client)
 {
 	struct i2c_adapter *adapter = client->adapter;
@@ -505,7 +511,7 @@
 	bool have_secondary;		/* true if chip has secondary limits */
 	bool secondary_is_max = false;	/* secondary limits reflect max */
 	int groups = 0;
-	const struct i2c_device_id *id = i2c_match_id(max16065_id, client);
+	enum chips chip = (uintptr_t)i2c_get_match_data(client);
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA
 				     | I2C_FUNC_SMBUS_READ_WORD_DATA))
@@ -515,12 +521,13 @@
 	if (unlikely(!data))
 		return -ENOMEM;
 
+	data->chip = chip;
 	data->client = client;
 	mutex_init(&data->update_lock);
 
-	data->num_adc = max16065_num_adc[id->driver_data];
-	data->have_current = max16065_have_current[id->driver_data];
-	have_secondary = max16065_have_secondary[id->driver_data];
+	data->num_adc = max16065_num_adc[chip];
+	data->have_current = max16065_have_current[chip];
+	have_secondary = max16065_have_secondary[chip];
 
 	if (have_secondary) {
 		val = i2c_smbus_read_byte_data(client, MAX16065_SW_ENABLE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/max6697.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/max6697.c
@@ -312,6 +312,7 @@
 		return ret;
 
 	mutex_lock(&data->update_lock);
+	temp = clamp_val(temp, -1000000, 1000000);	/* prevent underflow */
 	temp = DIV_ROUND_CLOSEST(temp, 1000) + data->temp_offset;
 	temp = clamp_val(temp, 0, data->type == max6581 ? 255 : 127);
 	data->temp[nr][index] = temp;
@@ -429,14 +430,14 @@
 static SENSOR_DEVICE_ATTR_RO(temp7_max_alarm, alarm, 21);
 static SENSOR_DEVICE_ATTR_RO(temp8_max_alarm, alarm, 23);
 
-static SENSOR_DEVICE_ATTR_RO(temp1_crit_alarm, alarm, 14);
+static SENSOR_DEVICE_ATTR_RO(temp1_crit_alarm, alarm, 15);
 static SENSOR_DEVICE_ATTR_RO(temp2_crit_alarm, alarm, 8);
 static SENSOR_DEVICE_ATTR_RO(temp3_crit_alarm, alarm, 9);
 static SENSOR_DEVICE_ATTR_RO(temp4_crit_alarm, alarm, 10);
 static SENSOR_DEVICE_ATTR_RO(temp5_crit_alarm, alarm, 11);
 static SENSOR_DEVICE_ATTR_RO(temp6_crit_alarm, alarm, 12);
 static SENSOR_DEVICE_ATTR_RO(temp7_crit_alarm, alarm, 13);
-static SENSOR_DEVICE_ATTR_RO(temp8_crit_alarm, alarm, 15);
+static SENSOR_DEVICE_ATTR_RO(temp8_crit_alarm, alarm, 14);
 
 static SENSOR_DEVICE_ATTR_RO(temp2_fault, alarm, 1);
 static SENSOR_DEVICE_ATTR_RO(temp3_fault, alarm, 2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/mlxreg-fan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/mlxreg-fan.c
@@ -151,6 +151,12 @@
 			if (err)
 				return err;
 
+			if (MLXREG_FAN_GET_FAULT(regval, tacho->mask)) {
+				/* FAN is broken - return zero for FAN speed. */
+				*val = 0;
+				return 0;
+			}
+
 			*val = MLXREG_FAN_GET_RPM(regval, fan->divider,
 						  fan->samples);
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/mr75203.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/mr75203.c
@@ -68,8 +68,9 @@
 
 /* VM Individual Macro Register */
 #define VM_COM_REG_SIZE	0x200
-#define VM_SDIF_DONE(n)	(VM_COM_REG_SIZE + 0x34 + 0x200 * (n))
-#define VM_SDIF_DATA(n)	(VM_COM_REG_SIZE + 0x40 + 0x200 * (n))
+#define VM_SDIF_DONE(vm)	(VM_COM_REG_SIZE + 0x34 + 0x200 * (vm))
+#define VM_SDIF_DATA(vm, ch)	\
+	(VM_COM_REG_SIZE + 0x40 + 0x200 * (vm) + 0x4 * (ch))
 
 /* SDA Slave Register */
 #define IP_CTRL			0x00
@@ -93,7 +94,7 @@
 #define VM_CH_REQ	BIT(21)
 
 #define IP_TMR			0x05
-#define POWER_DELAY_CYCLE_256	0x80
+#define POWER_DELAY_CYCLE_256	0x100
 #define POWER_DELAY_CYCLE_64	0x40
 
 #define PVT_POLL_DELAY_US	20
@@ -115,6 +116,7 @@
 	u32			t_num;
 	u32			p_num;
 	u32			v_num;
+	u32			c_num;
 	u32			ip_freq;
 	u8			*vm_idx;
 };
@@ -178,14 +180,15 @@
 {
 	struct pvt_device *pvt = dev_get_drvdata(dev);
 	struct regmap *v_map = pvt->v_map;
+	u8 vm_idx, ch_idx;
 	u32 n, stat;
-	u8 vm_idx;
 	int ret;
 
-	if (channel >= pvt->v_num)
+	if (channel >= pvt->v_num * pvt->c_num)
 		return -EINVAL;
 
-	vm_idx = pvt->vm_idx[channel];
+	vm_idx = pvt->vm_idx[channel / pvt->c_num];
+	ch_idx = channel % pvt->c_num;
 
 	switch (attr) {
 	case hwmon_in_input:
@@ -196,13 +199,23 @@
 		if (ret)
 			return ret;
 
-		ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx), &n);
+		ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx, ch_idx), &n);
 		if(ret < 0)
 			return ret;
 
 		n &= SAMPLE_DATA_MSK;
-		/* Convert the N bitstream count into voltage */
-		*val = (PVT_N_CONST * n - PVT_R_CONST) >> PVT_CONV_BITS;
+		/*
+		 * Convert the N bitstream count into voltage.
+		 * To support negative voltage calculation for 64bit machines
+		 * n must be cast to long, since n and *val differ both in
+		 * signedness and in size.
+		 * Division is used instead of right shift, because for signed
+		 * numbers, the sign bit is used to fill the vacated bit
+		 * positions, and if the number is negative, 1 is used.
+		 * BIT(x) may not be used instead of (1 << x) because it's
+		 * unsigned.
+		 */
+		*val = (PVT_N_CONST * (long)n - PVT_R_CONST) / (1 << PVT_CONV_BITS);
 
 		return 0;
 	default:
@@ -385,6 +398,19 @@
 		if (ret)
 			return ret;
 
+		val = (BIT(pvt->c_num) - 1) | VM_CH_INIT |
+		      IP_POLL << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if (ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
 		val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT |
 		      CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT |
 		      SDIF_WRN_W | SDIF_PROG;
@@ -499,8 +525,8 @@
 
 static int mr75203_probe(struct platform_device *pdev)
 {
+	u32 ts_num, vm_num, pd_num, ch_num, val, index, i;
 	const struct hwmon_channel_info **pvt_info;
-	u32 ts_num, vm_num, pd_num, val, index, i;
 	struct device *dev = &pdev->dev;
 	u32 *temp_config, *in_config;
 	struct device *hwmon_dev;
@@ -541,9 +567,11 @@
 	ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT;
 	pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT;
 	vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT;
+	ch_num = (val & CH_NUM_MSK) >> CH_NUM_SFT;
 	pvt->t_num = ts_num;
 	pvt->p_num = pd_num;
 	pvt->v_num = vm_num;
+	pvt->c_num = ch_num;
 	val = 0;
 	if (ts_num)
 		val++;
@@ -580,7 +608,7 @@
 	}
 
 	if (vm_num) {
-		u32 num = vm_num;
+		u32 total_ch;
 
 		ret = pvt_get_regmap(pdev, "vm", pvt);
 		if (ret)
@@ -594,30 +622,30 @@
 		ret = device_property_read_u8_array(dev, "intel,vm-map",
 						    pvt->vm_idx, vm_num);
 		if (ret) {
-			num = 0;
+			/*
+			 * Incase intel,vm-map property is not defined, we
+			 * assume incremental channel numbers.
+			 */
+			for (i = 0; i < vm_num; i++)
+				pvt->vm_idx[i] = i;
 		} else {
 			for (i = 0; i < vm_num; i++)
 				if (pvt->vm_idx[i] >= vm_num ||
 				    pvt->vm_idx[i] == 0xff) {
-					num = i;
+					pvt->v_num = i;
+					vm_num = i;
 					break;
 				}
 		}
 
-		/*
-		 * Incase intel,vm-map property is not defined, we assume
-		 * incremental channel numbers.
-		 */
-		for (i = num; i < vm_num; i++)
-			pvt->vm_idx[i] = i;
-
-		in_config = devm_kcalloc(dev, num + 1,
+		total_ch = ch_num * vm_num;
+		in_config = devm_kcalloc(dev, total_ch + 1,
 					 sizeof(*in_config), GFP_KERNEL);
 		if (!in_config)
 			return -ENOMEM;
 
-		memset32(in_config, HWMON_I_INPUT, num);
-		in_config[num] = 0;
+		memset32(in_config, HWMON_I_INPUT, total_ch);
+		in_config[total_ch] = 0;
 		pvt_in.config = in_config;
 
 		pvt_info[index++] = &pvt_in;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/nct6775.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/nct6775.c
@@ -420,8 +420,8 @@
 static const u16 NCT6776_REG_TOLERANCE_H[] = {
 	0x10c, 0x20c, 0x30c, 0x80c, 0x90c, 0xa0c, 0xb0c };
 
-static const u8 NCT6776_REG_PWM_MODE[] = { 0x04, 0, 0, 0, 0, 0 };
-static const u8 NCT6776_PWM_MODE_MASK[] = { 0x01, 0, 0, 0, 0, 0 };
+static const u8 NCT6776_REG_PWM_MODE[] = { 0x04, 0, 0, 0, 0, 0, 0 };
+static const u8 NCT6776_PWM_MODE_MASK[] = { 0x01, 0, 0, 0, 0, 0, 0 };
 
 static const u16 NCT6776_REG_FAN_MIN[] = {
 	0x63a, 0x63c, 0x63e, 0x640, 0x642, 0x64a, 0x64c };
@@ -2374,7 +2374,7 @@
 	if (err < 0)
 		return err;
 
-	val = clamp_val(DIV_ROUND_CLOSEST(val, 1000), -128, 127);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, -128000, 127000), 1000);
 
 	mutex_lock(&data->update_lock);
 	data->temp_offset[nr] = val;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/nct7802.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/nct7802.c
@@ -708,7 +708,7 @@
 	if (index >= 38 && index < 46 && !(reg & 0x01))		/* PECI 0 */
 		return 0;
 
-	if (index >= 0x46 && (!(reg & 0x02)))			/* PECI 1 */
+	if (index >= 46 && !(reg & 0x02))			/* PECI 1 */
 		return 0;
 
 	return attr->mode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/ntc_thermistor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/ntc_thermistor.c
@@ -55,6 +55,7 @@
 	[NTC_NCP21WB473]      = { "ncp21wb473",      TYPE_NCPXXWB473 },
 	[NTC_LAST]            = { },
 };
+MODULE_DEVICE_TABLE(platform, ntc_thermistor_id);
 
 /*
  * A compensation table should be sorted by the values of .ohm
@@ -173,40 +174,40 @@
 };
 
 static const struct ntc_compensation ncpXXxh103[] = {
-	{ .temp_c	= -40, .ohm	= 247565 },
-	{ .temp_c	= -35, .ohm	= 181742 },
-	{ .temp_c	= -30, .ohm	= 135128 },
-	{ .temp_c	= -25, .ohm	= 101678 },
-	{ .temp_c	= -20, .ohm	= 77373 },
-	{ .temp_c	= -15, .ohm	= 59504 },
-	{ .temp_c	= -10, .ohm	= 46222 },
-	{ .temp_c	= -5, .ohm	= 36244 },
-	{ .temp_c	= 0, .ohm	= 28674 },
-	{ .temp_c	= 5, .ohm	= 22878 },
-	{ .temp_c	= 10, .ohm	= 18399 },
-	{ .temp_c	= 15, .ohm	= 14910 },
-	{ .temp_c	= 20, .ohm	= 12169 },
+	{ .temp_c	= -40, .ohm	= 195652 },
+	{ .temp_c	= -35, .ohm	= 148171 },
+	{ .temp_c	= -30, .ohm	= 113347 },
+	{ .temp_c	= -25, .ohm	= 87559 },
+	{ .temp_c	= -20, .ohm	= 68237 },
+	{ .temp_c	= -15, .ohm	= 53650 },
+	{ .temp_c	= -10, .ohm	= 42506 },
+	{ .temp_c	= -5, .ohm	= 33892 },
+	{ .temp_c	= 0, .ohm	= 27219 },
+	{ .temp_c	= 5, .ohm	= 22021 },
+	{ .temp_c	= 10, .ohm	= 17926 },
+	{ .temp_c	= 15, .ohm	= 14674 },
+	{ .temp_c	= 20, .ohm	= 12081 },
 	{ .temp_c	= 25, .ohm	= 10000 },
-	{ .temp_c	= 30, .ohm	= 8271 },
-	{ .temp_c	= 35, .ohm	= 6883 },
-	{ .temp_c	= 40, .ohm	= 5762 },
-	{ .temp_c	= 45, .ohm	= 4851 },
-	{ .temp_c	= 50, .ohm	= 4105 },
-	{ .temp_c	= 55, .ohm	= 3492 },
-	{ .temp_c	= 60, .ohm	= 2985 },
-	{ .temp_c	= 65, .ohm	= 2563 },
-	{ .temp_c	= 70, .ohm	= 2211 },
-	{ .temp_c	= 75, .ohm	= 1915 },
-	{ .temp_c	= 80, .ohm	= 1666 },
-	{ .temp_c	= 85, .ohm	= 1454 },
-	{ .temp_c	= 90, .ohm	= 1275 },
-	{ .temp_c	= 95, .ohm	= 1121 },
-	{ .temp_c	= 100, .ohm	= 990 },
-	{ .temp_c	= 105, .ohm	= 876 },
-	{ .temp_c	= 110, .ohm	= 779 },
-	{ .temp_c	= 115, .ohm	= 694 },
-	{ .temp_c	= 120, .ohm	= 620 },
-	{ .temp_c	= 125, .ohm	= 556 },
+	{ .temp_c	= 30, .ohm	= 8315 },
+	{ .temp_c	= 35, .ohm	= 6948 },
+	{ .temp_c	= 40, .ohm	= 5834 },
+	{ .temp_c	= 45, .ohm	= 4917 },
+	{ .temp_c	= 50, .ohm	= 4161 },
+	{ .temp_c	= 55, .ohm	= 3535 },
+	{ .temp_c	= 60, .ohm	= 3014 },
+	{ .temp_c	= 65, .ohm	= 2586 },
+	{ .temp_c	= 70, .ohm	= 2228 },
+	{ .temp_c	= 75, .ohm	= 1925 },
+	{ .temp_c	= 80, .ohm	= 1669 },
+	{ .temp_c	= 85, .ohm	= 1452 },
+	{ .temp_c	= 90, .ohm	= 1268 },
+	{ .temp_c	= 95, .ohm	= 1110 },
+	{ .temp_c	= 100, .ohm	= 974 },
+	{ .temp_c	= 105, .ohm	= 858 },
+	{ .temp_c	= 110, .ohm	= 758 },
+	{ .temp_c	= 115, .ohm	= 672 },
+	{ .temp_c	= 120, .ohm	= 596 },
+	{ .temp_c	= 125, .ohm	= 531 },
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/nzxt-kraken2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/nzxt-kraken2.c
@@ -161,13 +161,13 @@
 	ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW);
 	if (ret) {
 		hid_err(hdev, "hid hw start failed with %d\n", ret);
-		goto fail_and_stop;
+		return ret;
 	}
 
 	ret = hid_hw_open(hdev);
 	if (ret) {
 		hid_err(hdev, "hid hw open failed with %d\n", ret);
-		goto fail_and_close;
+		goto fail_and_stop;
 	}
 
 	priv->hwmon_dev = hwmon_device_register_with_info(&hdev->dev, "kraken2",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/occ/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/occ/common.c
@@ -132,22 +132,20 @@
 static int occ_poll(struct occ *occ)
 {
 	int rc;
-	u16 checksum = occ->poll_cmd_data + occ->seq_no + 1;
-	u8 cmd[8];
+	u8 cmd[7];
 	struct occ_poll_response_header *header;
 
 	/* big endian */
-	cmd[0] = occ->seq_no++;		/* sequence number */
+	cmd[0] = 0;			/* sequence number */
 	cmd[1] = 0;			/* cmd type */
 	cmd[2] = 0;			/* data length msb */
 	cmd[3] = 1;			/* data length lsb */
 	cmd[4] = occ->poll_cmd_data;	/* data */
-	cmd[5] = checksum >> 8;		/* checksum msb */
-	cmd[6] = checksum & 0xFF;	/* checksum lsb */
-	cmd[7] = 0;
+	cmd[5] = 0;			/* checksum msb */
+	cmd[6] = 0;			/* checksum lsb */
 
 	/* mutex should already be locked if necessary */
-	rc = occ->send_cmd(occ, cmd);
+	rc = occ->send_cmd(occ, cmd, sizeof(cmd), &occ->resp, sizeof(occ->resp));
 	if (rc) {
 		occ->last_error = rc;
 		if (occ->error_count++ > OCC_ERROR_COUNT_THRESHOLD)
@@ -184,25 +182,24 @@
 {
 	int rc;
 	u8 cmd[8];
-	u16 checksum = 0x24;
+	u8 resp[8];
 	__be16 user_power_cap_be = cpu_to_be16(user_power_cap);
 
-	cmd[0] = 0;
-	cmd[1] = 0x22;
-	cmd[2] = 0;
-	cmd[3] = 2;
+	cmd[0] = 0;	/* sequence number */
+	cmd[1] = 0x22;	/* cmd type */
+	cmd[2] = 0;	/* data length msb */
+	cmd[3] = 2;	/* data length lsb */
 
 	memcpy(&cmd[4], &user_power_cap_be, 2);
 
-	checksum += cmd[4] + cmd[5];
-	cmd[6] = checksum >> 8;
-	cmd[7] = checksum & 0xFF;
+	cmd[6] = 0;	/* checksum msb */
+	cmd[7] = 0;	/* checksum lsb */
 
 	rc = mutex_lock_interruptible(&occ->lock);
 	if (rc)
 		return rc;
 
-	rc = occ->send_cmd(occ, cmd);
+	rc = occ->send_cmd(occ, cmd, sizeof(cmd), resp, sizeof(resp));
 
 	mutex_unlock(&occ->lock);
 
@@ -1144,8 +1141,6 @@
 {
 	int rc;
 
-	/* start with 1 to avoid false match with zero-initialized SRAM buffer */
-	occ->seq_no = 1;
 	mutex_init(&occ->lock);
 	occ->groups[0] = &occ->group;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/occ/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/occ/common.h
@@ -95,9 +95,9 @@
 	struct occ_sensors sensors;
 
 	int powr_sample_time_us;	/* average power sample time */
-	u8 seq_no;
 	u8 poll_cmd_data;		/* to perform OCC poll command */
-	int (*send_cmd)(struct occ *occ, u8 *cmd);
+	int (*send_cmd)(struct occ *occ, u8 *cmd, size_t len, void *resp,
+			size_t resp_len);
 
 	unsigned long next_update;
 	struct mutex lock;		/* lock OCC access */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/occ/p8_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/occ/p8_i2c.c
@@ -97,18 +97,22 @@
 }
 
 static int p8_i2c_occ_putscom_be(struct i2c_client *client, u32 address,
-				 u8 *data)
+				 u8 *data, size_t len)
 {
-	__be32 data0, data1;
+	__be32 data0 = 0, data1 = 0;
 
-	memcpy(&data0, data, 4);
-	memcpy(&data1, data + 4, 4);
+	memcpy(&data0, data, min_t(size_t, len, 4));
+	if (len > 4) {
+		len -= 4;
+		memcpy(&data1, data + 4, min_t(size_t, len, 4));
+	}
 
 	return p8_i2c_occ_putscom_u32(client, address, be32_to_cpu(data0),
 				      be32_to_cpu(data1));
 }
 
-static int p8_i2c_occ_send_cmd(struct occ *occ, u8 *cmd)
+static int p8_i2c_occ_send_cmd(struct occ *occ, u8 *cmd, size_t len,
+			       void *resp, size_t resp_len)
 {
 	int i, rc;
 	unsigned long start;
@@ -117,7 +121,7 @@
 	const long wait_time = msecs_to_jiffies(OCC_CMD_IN_PRG_WAIT_MS);
 	struct p8_i2c_occ *ctx = to_p8_i2c_occ(occ);
 	struct i2c_client *client = ctx->client;
-	struct occ_response *resp = &occ->resp;
+	struct occ_response *or = (struct occ_response *)resp;
 
 	start = jiffies;
 
@@ -127,7 +131,7 @@
 		return rc;
 
 	/* write command (expected to already be BE), we need bus-endian... */
-	rc = p8_i2c_occ_putscom_be(client, OCB_DATA3, cmd);
+	rc = p8_i2c_occ_putscom_be(client, OCB_DATA3, cmd, len);
 	if (rc)
 		return rc;
 
@@ -148,7 +152,7 @@
 			return rc;
 
 		/* wait for OCC */
-		if (resp->return_status == OCC_RESP_CMD_IN_PRG) {
+		if (or->return_status == OCC_RESP_CMD_IN_PRG) {
 			rc = -EALREADY;
 
 			if (time_after(jiffies, start + timeout))
@@ -160,7 +164,7 @@
 	} while (rc);
 
 	/* check the OCC response */
-	switch (resp->return_status) {
+	switch (or->return_status) {
 	case OCC_RESP_CMD_IN_PRG:
 		rc = -ETIMEDOUT;
 		break;
@@ -189,8 +193,8 @@
 	if (rc < 0)
 		return rc;
 
-	data_length = get_unaligned_be16(&resp->data_length);
-	if (data_length > OCC_RESP_DATA_BYTES)
+	data_length = get_unaligned_be16(&or->data_length);
+	if ((data_length + 7) > resp_len)
 		return -EMSGSIZE;
 
 	/* fetch the rest of the response data */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/occ/p9_sbe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/occ/p9_sbe.c
@@ -16,18 +16,17 @@
 
 #define to_p9_sbe_occ(x)	container_of((x), struct p9_sbe_occ, occ)
 
-static int p9_sbe_occ_send_cmd(struct occ *occ, u8 *cmd)
+static int p9_sbe_occ_send_cmd(struct occ *occ, u8 *cmd, size_t len,
+			       void *resp, size_t resp_len)
 {
-	struct occ_response *resp = &occ->resp;
 	struct p9_sbe_occ *ctx = to_p9_sbe_occ(occ);
-	size_t resp_len = sizeof(*resp);
 	int rc;
 
-	rc = fsi_occ_submit(ctx->sbe, cmd, 8, resp, &resp_len);
+	rc = fsi_occ_submit(ctx->sbe, cmd, len, resp, &resp_len);
 	if (rc < 0)
 		return rc;
 
-	switch (resp->return_status) {
+	switch (((struct occ_response *)resp)->return_status) {
 	case OCC_RESP_CMD_IN_PRG:
 		rc = -ETIMEDOUT;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/Kconfig
@@ -340,6 +340,26 @@
 	  This driver can also be built as a module. If so, the module will
 	  be called tps53679.
 
+config SENSORS_TPS544
+	tristate "TI TPS544"
+	help
+	  If you say yes here you get hardware monitoring support for Texas
+	  Instruments TPS544.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called tps544.
+
+config SENSORS_TPS544_REGULATOR
+	bool "Regulator support for TPS544"
+	depends on SENSORS_TPS544
+	select REGULATOR
+	help
+	  If you say yes here you get regulator support for Texas Instruments
+	  TPS544.
+
+	  This driver is dependent on TPS544 sensor and it can also be built
+	  as a module.
+
 config SENSORS_UCD9000
 	tristate "TI UCD90120, UCD90124, UCD90160, UCD90320, UCD9090, UCD90910"
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/Makefile
@@ -37,6 +37,7 @@
 obj-$(CONFIG_SENSORS_STPDDC60)	+= stpddc60.o
 obj-$(CONFIG_SENSORS_TPS40422)	+= tps40422.o
 obj-$(CONFIG_SENSORS_TPS53679)	+= tps53679.o
+obj-$(CONFIG_SENSORS_TPS544)	+= tps544.o
 obj-$(CONFIG_SENSORS_UCD9000)	+= ucd9000.o
 obj-$(CONFIG_SENSORS_UCD9200)	+= ucd9200.o
 obj-$(CONFIG_SENSORS_XDPE122)	+= xdpe12284.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/adm1266.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/adm1266.c
@@ -301,6 +301,7 @@
 	data->gc.label = name;
 	data->gc.parent = &data->client->dev;
 	data->gc.owner = THIS_MODULE;
+	data->gc.can_sleep = true;
 	data->gc.base = -1;
 	data->gc.names = data->gpio_names;
 	data->gc.ngpio = ARRAY_SIZE(data->gpio_names);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/adm1275.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/adm1275.c
@@ -37,10 +37,13 @@
 
 #define ADM1272_IRANGE			BIT(0)
 
+#define ADM1278_TSFILT			BIT(15)
 #define ADM1278_TEMP1_EN		BIT(3)
 #define ADM1278_VIN_EN			BIT(2)
 #define ADM1278_VOUT_EN			BIT(1)
 
+#define ADM1278_PMON_DEFCONFIG		(ADM1278_VOUT_EN | ADM1278_TEMP1_EN | ADM1278_TSFILT)
+
 #define ADM1293_IRANGE_25		0
 #define ADM1293_IRANGE_50		BIT(6)
 #define ADM1293_IRANGE_100		BIT(7)
@@ -462,6 +465,22 @@
 };
 MODULE_DEVICE_TABLE(i2c, adm1275_id);
 
+/* Enable VOUT & TEMP1 if not enabled (disabled by default) */
+static int adm1275_enable_vout_temp(struct i2c_client *client, int config)
+{
+	int ret;
+
+	if ((config & ADM1278_PMON_DEFCONFIG) != ADM1278_PMON_DEFCONFIG) {
+		config |= ADM1278_PMON_DEFCONFIG;
+		ret = i2c_smbus_write_word_data(client, ADM1275_PMON_CONFIG, config);
+		if (ret < 0) {
+			dev_err(&client->dev, "Failed to enable VOUT/TEMP1 monitoring\n");
+			return ret;
+		}
+	}
+	return 0;
+}
+
 static int adm1275_probe(struct i2c_client *client)
 {
 	s32 (*config_read_fn)(const struct i2c_client *client, u8 reg);
@@ -475,6 +494,7 @@
 	int vindex = -1, voindex = -1, cindex = -1, pindex = -1;
 	int tindex = -1;
 	u32 shunt;
+	u32 avg;
 
 	if (!i2c_check_functionality(client->adapter,
 				     I2C_FUNC_SMBUS_READ_BYTE_DATA
@@ -614,19 +634,10 @@
 			PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
 			PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP;
 
-		/* Enable VOUT & TEMP1 if not enabled (disabled by default) */
-		if ((config & (ADM1278_VOUT_EN | ADM1278_TEMP1_EN)) !=
-		    (ADM1278_VOUT_EN | ADM1278_TEMP1_EN)) {
-			config |= ADM1278_VOUT_EN | ADM1278_TEMP1_EN;
-			ret = i2c_smbus_write_byte_data(client,
-							ADM1275_PMON_CONFIG,
-							config);
-			if (ret < 0) {
-				dev_err(&client->dev,
-					"Failed to enable VOUT monitoring\n");
-				return -ENODEV;
-			}
-		}
+		ret = adm1275_enable_vout_temp(client, config);
+		if (ret)
+			return ret;
+
 		if (config & ADM1278_VIN_EN)
 			info->func[0] |= PMBUS_HAVE_VIN;
 		break;
@@ -683,19 +694,9 @@
 			PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
 			PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP;
 
-		/* Enable VOUT & TEMP1 if not enabled (disabled by default) */
-		if ((config & (ADM1278_VOUT_EN | ADM1278_TEMP1_EN)) !=
-		    (ADM1278_VOUT_EN | ADM1278_TEMP1_EN)) {
-			config |= ADM1278_VOUT_EN | ADM1278_TEMP1_EN;
-			ret = i2c_smbus_write_byte_data(client,
-							ADM1275_PMON_CONFIG,
-							config);
-			if (ret < 0) {
-				dev_err(&client->dev,
-					"Failed to enable VOUT monitoring\n");
-				return -ENODEV;
-			}
-		}
+		ret = adm1275_enable_vout_temp(client, config);
+		if (ret)
+			return ret;
 
 		if (config & ADM1278_VIN_EN)
 			info->func[0] |= PMBUS_HAVE_VIN;
@@ -756,6 +757,43 @@
 		return -ENODEV;
 	}
 
+	if (data->have_power_sampling &&
+	    of_property_read_u32(client->dev.of_node,
+				 "adi,power-sample-average", &avg) == 0) {
+		if (!avg || avg > ADM1275_SAMPLES_AVG_MAX ||
+		    BIT(__fls(avg)) != avg) {
+			dev_err(&client->dev,
+				"Invalid number of power samples");
+			return -EINVAL;
+		}
+		ret = adm1275_write_pmon_config(data, client, true,
+						ilog2(avg));
+		if (ret < 0) {
+			dev_err(&client->dev,
+				"Setting power sample averaging failed with error %d",
+				ret);
+			return ret;
+		}
+	}
+
+	if (of_property_read_u32(client->dev.of_node,
+				"adi,volt-curr-sample-average", &avg) == 0) {
+		if (!avg || avg > ADM1275_SAMPLES_AVG_MAX ||
+		    BIT(__fls(avg)) != avg) {
+			dev_err(&client->dev,
+				"Invalid number of voltage/current samples");
+			return -EINVAL;
+		}
+		ret = adm1275_write_pmon_config(data, client, false,
+						ilog2(avg));
+		if (ret < 0) {
+			dev_err(&client->dev,
+				"Setting voltage and current sample averaging failed with error %d",
+				ret);
+			return ret;
+		}
+	}
+
 	if (voindex < 0)
 		voindex = vindex;
 	if (vindex >= 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/bel-pfe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/bel-pfe.c
@@ -17,12 +17,13 @@
 enum chips {pfe1100, pfe3000};
 
 /*
- * Disable status check for pfe3000 devices, because some devices report
- * communication error (invalid command) for VOUT_MODE command (0x20)
- * although correct VOUT_MODE (0x16) is returned: it leads to incorrect
- * exponent in linear mode.
+ * Disable status check because some devices report communication error
+ * (invalid command) for VOUT_MODE command (0x20) although the correct
+ * VOUT_MODE (0x16) is returned: it leads to incorrect exponent in linear
+ * mode.
+ * This affects both pfe3000 and pfe1100.
  */
-static struct pmbus_platform_data pfe3000_plat_data = {
+static struct pmbus_platform_data pfe_plat_data = {
 	.flags = PMBUS_SKIP_STATUS_CHECK,
 };
 
@@ -94,16 +95,15 @@
 	int model;
 
 	model = (int)i2c_match_id(pfe_device_id, client)->driver_data;
+	client->dev.platform_data = &pfe_plat_data;
 
 	/*
 	 * PFE3000-12-069RA devices may not stay in page 0 during device
 	 * probe which leads to probe failure (read status word failed).
 	 * So let's set the device to page 0 at the beginning.
 	 */
-	if (model == pfe3000) {
-		client->dev.platform_data = &pfe3000_plat_data;
+	if (model == pfe3000)
 		i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
-	}
 
 	return pmbus_do_probe(client, &pfe_driver_info[model]);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/fsp-3y.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/fsp-3y.c
@@ -180,7 +180,6 @@
 			PMBUS_HAVE_FAN12,
 		.func[YM2151_PAGE_5VSB_LOG] =
 			PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT,
-			PMBUS_HAVE_IIN,
 		.read_word_data = fsp3y_read_word_data,
 		.read_byte_data = fsp3y_read_byte_data,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/lm25066.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/lm25066.c
@@ -51,26 +51,31 @@
 #define PSC_CURRENT_IN_L	(PSC_NUM_CLASSES)
 #define PSC_POWER_L		(PSC_NUM_CLASSES + 1)
 
-static struct __coeff lm25066_coeff[6][PSC_NUM_CLASSES + 2] = {
+static struct __coeff lm25066_coeff[][PSC_NUM_CLASSES + 2] = {
 	[lm25056] = {
 		[PSC_VOLTAGE_IN] = {
 			.m = 16296,
+			.b = 1343,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN] = {
 			.m = 13797,
+			.b = -1833,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN_L] = {
 			.m = 6726,
+			.b = -537,
 			.R = -2,
 		},
 		[PSC_POWER] = {
 			.m = 5501,
+			.b = -2908,
 			.R = -3,
 		},
 		[PSC_POWER_L] = {
 			.m = 26882,
+			.b = -5646,
 			.R = -4,
 		},
 		[PSC_TEMPERATURE] = {
@@ -82,26 +87,32 @@
 	[lm25066] = {
 		[PSC_VOLTAGE_IN] = {
 			.m = 22070,
+			.b = -1800,
 			.R = -2,
 		},
 		[PSC_VOLTAGE_OUT] = {
 			.m = 22070,
+			.b = -1800,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN] = {
 			.m = 13661,
+			.b = -5200,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN_L] = {
 			.m = 6852,
+			.b = -3100,
 			.R = -2,
 		},
 		[PSC_POWER] = {
 			.m = 736,
+			.b = -3300,
 			.R = -2,
 		},
 		[PSC_POWER_L] = {
 			.m = 369,
+			.b = -1900,
 			.R = -2,
 		},
 		[PSC_TEMPERATURE] = {
@@ -111,26 +122,32 @@
 	[lm5064] = {
 		[PSC_VOLTAGE_IN] = {
 			.m = 4611,
+			.b = -642,
 			.R = -2,
 		},
 		[PSC_VOLTAGE_OUT] = {
 			.m = 4621,
+			.b = 423,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN] = {
 			.m = 10742,
+			.b = 1552,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN_L] = {
 			.m = 5456,
+			.b = 2118,
 			.R = -2,
 		},
 		[PSC_POWER] = {
 			.m = 1204,
+			.b = 8524,
 			.R = -3,
 		},
 		[PSC_POWER_L] = {
 			.m = 612,
+			.b = 11202,
 			.R = -3,
 		},
 		[PSC_TEMPERATURE] = {
@@ -140,26 +157,32 @@
 	[lm5066] = {
 		[PSC_VOLTAGE_IN] = {
 			.m = 4587,
+			.b = -1200,
 			.R = -2,
 		},
 		[PSC_VOLTAGE_OUT] = {
 			.m = 4587,
+			.b = -2400,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN] = {
 			.m = 10753,
+			.b = -1200,
 			.R = -2,
 		},
 		[PSC_CURRENT_IN_L] = {
 			.m = 5405,
+			.b = -600,
 			.R = -2,
 		},
 		[PSC_POWER] = {
 			.m = 1204,
+			.b = -6000,
 			.R = -3,
 		},
 		[PSC_POWER_L] = {
 			.m = 605,
+			.b = -8000,
 			.R = -3,
 		},
 		[PSC_TEMPERATURE] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/mp2888.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/mp2888.c
@@ -34,7 +34,7 @@
 	int curr_sense_gain;
 };
 
-#define to_mp2888_data(x)  container_of(x, struct mp2888_data, info)
+#define to_mp2888_data(x)	container_of(x, struct mp2888_data, info)
 
 static int mp2888_read_byte_data(struct i2c_client *client, int page, int reg)
 {
@@ -109,7 +109,7 @@
 	 * - Kcs is the DrMOS current sense gain of power stage, which is obtained from the
 	 *   register MP2888_MFR_VR_CONFIG1, bits 13-12 with the following selection of DrMOS
 	 *   (data->curr_sense_gain):
-	 *   00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A.
+	 *   00b - 8.5µA/A, 01b - 9.7µA/A, 1b - 10µA/A, 11b - 5µA/A.
 	 * - Rcs is the internal phase current sense resistor. This parameter depends on hardware
 	 *   assembly. By default it is set to 1kΩ. In case of different assembly, user should
 	 *   scale this parameter by dividing it by Rcs.
@@ -118,10 +118,9 @@
 	 * because sampling of current occurrence of bit weight has a big deviation, especially for
 	 * light load.
 	 */
-	ret = DIV_ROUND_CLOSEST(ret * 100 - 9800, data->curr_sense_gain);
-	ret = (data->phase_curr_resolution) ? ret * 2 : ret;
+	ret = DIV_ROUND_CLOSEST(ret * 200 - 19600, data->curr_sense_gain);
 	/* Scale according to total current resolution. */
-	ret = (data->total_curr_resolution) ? ret * 8 : ret * 4;
+	ret = (data->total_curr_resolution) ? ret * 2 : ret;
 	return ret;
 }
 
@@ -212,7 +211,7 @@
 		ret = pmbus_read_word_data(client, page, phase, reg);
 		if (ret < 0)
 			return ret;
-		ret = data->total_curr_resolution ? ret * 2 : ret;
+		ret = data->total_curr_resolution ? ret : DIV_ROUND_CLOSEST(ret, 2);
 		break;
 	case PMBUS_POUT_OP_WARN_LIMIT:
 		ret = pmbus_read_word_data(client, page, phase, reg);
@@ -223,7 +222,7 @@
 		 * set 1. Actual power is reported with 0.5W or 1W respectively resolution. Scaling
 		 * is needed to match both.
 		 */
-		ret = data->total_curr_resolution ? ret * 4 : ret * 2;
+		ret = data->total_curr_resolution ? ret * 2 : ret;
 		break;
 	/*
 	 * The below registers are not implemented by device or implemented not according to the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/pmbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/pmbus.c
@@ -103,6 +103,8 @@
 		if (pmbus_check_byte_register(client, 0, PMBUS_PAGE)) {
 			int page;
 
+			info->pages = PMBUS_PAGES;
+
 			for (page = 1; page < PMBUS_PAGES; page++) {
 				if (pmbus_set_page(client, page, 0xff) < 0)
 					break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/pmbus.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/pmbus.h
@@ -319,6 +319,7 @@
 /*
  * STATUS_VOUT, STATUS_INPUT
  */
+#define PB_VOLTAGE_VIN_OFF		BIT(3)
 #define PB_VOLTAGE_UV_FAULT		BIT(4)
 #define PB_VOLTAGE_UV_WARNING		BIT(5)
 #define PB_VOLTAGE_OV_WARNING		BIT(6)
@@ -408,6 +409,12 @@
 enum pmbus_data_format { linear = 0, direct, vid };
 enum vrm_version { vr11 = 0, vr12, vr13, imvp9, amd625mv };
 
+/* PMBus revision identifiers */
+#define PMBUS_REV_10 0x00	/* PMBus revision 1.0 */
+#define PMBUS_REV_11 0x11	/* PMBus revision 1.1 */
+#define PMBUS_REV_12 0x22	/* PMBus revision 1.2 */
+#define PMBUS_REV_13 0x33	/* PMBus revision 1.3 */
+
 struct pmbus_driver_info {
 	int pages;		/* Total number of pages */
 	u8 phases[PMBUS_PAGES];	/* Number of phases per page */
@@ -437,6 +444,8 @@
 	int (*read_byte_data)(struct i2c_client *client, int page, int reg);
 	int (*read_word_data)(struct i2c_client *client, int page, int phase,
 			      int reg);
+	int (*write_byte_data)(struct i2c_client *client, int page, int reg,
+			      u8 byte);
 	int (*write_word_data)(struct i2c_client *client, int page, int reg,
 			       u16 word);
 	int (*write_byte)(struct i2c_client *client, int page, u8 value);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/pmbus_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/pmbus_core.c
@@ -82,6 +82,8 @@
 
 	u32 flags;		/* from platform data */
 
+	u8 revision;	/* The PMBus revision the device is compliant with */
+
 	int exponent[PMBUS_PAGES];
 				/* linear mode: exponent for output voltages */
 
@@ -276,6 +278,24 @@
 	return pmbus_write_word_data(client, page, reg, word);
 }
 
+/*
+ * _pmbus_write_byte_data() is similar to pmbus_write_byte_data(), but checks if
+ * a device specific mapping function exists and calls it if necessary.
+ */
+static int _pmbus_write_byte_data(struct i2c_client *client, int page, int reg, u8 value)
+{
+	struct pmbus_data *data = i2c_get_clientdata(client);
+	const struct pmbus_driver_info *info = data->info;
+	int status;
+
+	if (info->write_byte_data) {
+		status = info->write_byte_data(client, page, reg, value);
+		if (status != -ENODATA)
+			return status;
+	}
+	return pmbus_write_byte_data(client, page, reg, value);
+}
+
 int pmbus_update_fan(struct i2c_client *client, int page, int id,
 		     u8 config, u8 mask, u16 command)
 {
@@ -290,7 +310,7 @@
 
 	to = (from & ~mask) | (config & mask);
 	if (to != from) {
-		rv = pmbus_write_byte_data(client, page,
+		rv = _pmbus_write_byte_data(client, page,
 					   pmbus_fan_config_registers[id], to);
 		if (rv < 0)
 			return rv;
@@ -397,7 +417,7 @@
 	tmp = (rv & ~mask) | (value & mask);
 
 	if (tmp != rv)
-		rv = pmbus_write_byte_data(client, page, reg, tmp);
+		rv = _pmbus_write_byte_data(client, page, reg, tmp);
 
 	return rv;
 }
@@ -911,6 +931,16 @@
 		pmbus_update_sensor_data(client, s2);
 
 	regval = status & mask;
+	if (regval) {
+		if (data->revision >= PMBUS_REV_12) {
+			ret = _pmbus_write_byte_data(client, page, reg, regval);
+			if (ret)
+				goto unlock;
+		} else {
+			pmbus_clear_fault_page(client, page);
+		}
+
+	}
 	if (s1 && s2) {
 		s64 v1, v2;
 
@@ -1368,7 +1398,7 @@
 		.reg = PMBUS_VIN_UV_FAULT_LIMIT,
 		.attr = "lcrit",
 		.alarm = "lcrit_alarm",
-		.sbit = PB_VOLTAGE_UV_FAULT,
+		.sbit = PB_VOLTAGE_UV_FAULT | PB_VOLTAGE_VIN_OFF,
 	}, {
 		.reg = PMBUS_VIN_OV_WARN_LIMIT,
 		.attr = "max",
@@ -2304,6 +2334,21 @@
 	int page, ret;
 
 	/*
+	 * Figure out if PEC is enabled before accessing any other register.
+	 * Make sure PEC is disabled, will be enabled later if needed.
+	 */
+	client->flags &= ~I2C_CLIENT_PEC;
+
+	/* Enable PEC if the controller and bus supports it */
+	if (!(data->flags & PMBUS_NO_CAPABILITY)) {
+		ret = i2c_smbus_read_byte_data(client, PMBUS_CAPABILITY);
+		if (ret >= 0 && (ret & PB_CAPABILITY_ERROR_CHECK)) {
+			if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_PEC))
+				client->flags |= I2C_CLIENT_PEC;
+		}
+	}
+
+	/*
 	 * Some PMBus chips don't support PMBUS_STATUS_WORD, so try
 	 * to use PMBUS_STATUS_BYTE instead if that is the case.
 	 * Bail out if both registers are not supported.
@@ -2321,16 +2366,6 @@
 		data->has_status_word = true;
 	}
 
-	/* Enable PEC if the controller and bus supports it */
-	if (!(data->flags & PMBUS_NO_CAPABILITY)) {
-		ret = i2c_smbus_read_byte_data(client, PMBUS_CAPABILITY);
-		if (ret >= 0 && (ret & PB_CAPABILITY_ERROR_CHECK)) {
-			if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_PEC)) {
-				client->flags |= I2C_CLIENT_PEC;
-			}
-		}
-	}
-
 	/*
 	 * Check if the chip is write protected. If it is, we can not clear
 	 * faults, and we should not try it. Also, in that case, writes into
@@ -2342,6 +2377,10 @@
 			data->flags |= PMBUS_WRITE_PROTECTED | PMBUS_SKIP_STATUS_CHECK;
 	}
 
+	ret = i2c_smbus_read_byte_data(client, PMBUS_REVISION);
+	if (ret >= 0)
+		data->revision = ret;
+
 	if (data->info->pages)
 		pmbus_clear_faults(client);
 	else
@@ -2386,10 +2425,14 @@
 {
 	struct device *dev = rdev_get_dev(rdev);
 	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct pmbus_data *data = i2c_get_clientdata(client);
 	u8 page = rdev_get_id(rdev);
 	int ret;
 
+	mutex_lock(&data->update_lock);
 	ret = pmbus_read_byte_data(client, page, PMBUS_OPERATION);
+	mutex_unlock(&data->update_lock);
+
 	if (ret < 0)
 		return ret;
 
@@ -2400,11 +2443,17 @@
 {
 	struct device *dev = rdev_get_dev(rdev);
 	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct pmbus_data *data = i2c_get_clientdata(client);
 	u8 page = rdev_get_id(rdev);
+	int ret;
+
+	mutex_lock(&data->update_lock);
+	ret = pmbus_update_byte_data(client, page, PMBUS_OPERATION,
+				     PB_OPERATION_CONTROL_ON,
+				     enable ? PB_OPERATION_CONTROL_ON : 0);
+	mutex_unlock(&data->update_lock);
 
-	return pmbus_update_byte_data(client, page, PMBUS_OPERATION,
-				      PB_OPERATION_CONTROL_ON,
-				      enable ? PB_OPERATION_CONTROL_ON : 0);
+	return ret;
 }
 
 static int pmbus_regulator_enable(struct regulator_dev *rdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/tps544.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/tps544.c
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * TPS544B25 power regulator driver
+ *
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/regulator/driver.h>
+#include "pmbus.h"
+
+#define TPS544_NUM_PAGES		1
+
+struct tps544_data {
+	struct device *dev;
+	u16 vout_min[TPS544_NUM_PAGES], vout_max[TPS544_NUM_PAGES];
+	struct pmbus_driver_info info;
+};
+
+struct vlut {
+	int vol;
+	u16 vloop;
+	u16 v_ovfault;
+	u16 v_ovwarn;
+	u16 vmax;
+	u16 mfr_vmin;
+	u16 v_uvwarn;
+	u16 v_uvfault;
+};
+
+#if IS_ENABLED(CONFIG_SENSORS_TPS544_REGULATOR)
+#define TPS544_MFR_VOUT_MIN		0xA4
+#define TPS544_MFR_RESTORE_DEF_ALL	0x12
+#define TPS544_MFR_IOUT_CAL_OFFSET	0x39
+
+#define TPS544_VOUTREAD_MULTIPLIER	1950
+#define TPS544_IOUTREAD_MULTIPLIER	62500
+#define TPS544_IOUTREAD_MASK		GENMASK(9, 0)
+
+#define TPS544_VOUT_LIMIT		5300000
+
+#define to_tps544_data(x) container_of(x, struct tps544_data, info)
+
+/*
+ * This currently supports 3 voltage out buckets:
+ * 0.5V to 1.3V
+ * 1.3V to 2.6V
+ * 2.6V to 5.3V
+ * Any requested voltage will be mapped to one of these buckets and
+ * VOUT will be programmed with 0.1V granularity.
+ */
+static const struct vlut tps544_vout[3] = {
+	{500000, 0xF004, 0x0290, 0x0285, 0x0300, 0x0100, 0x00CD, 0x009A},
+	{1300000, 0xF002, 0x059A, 0x0566, 0x0600, 0x0100, 0x0143, 0x0130},
+	{2600000, 0xF001, 0x0B00, 0x0A9A, 0x0A00, 0x0100, 0x0143, 0x0130}
+};
+#endif
+
+static int tps544_read_word_data(struct i2c_client *client, int page, int phase, int reg)
+{
+	return pmbus_read_word_data(client, page, phase, reg);
+}
+
+static int tps544_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	return pmbus_read_byte_data(client, page, reg);
+}
+
+static int tps544_write_byte(struct i2c_client *client, int page, u8 byte)
+{
+	return pmbus_write_byte(client, page, byte);
+}
+
+static int tps544_write_word_data(struct i2c_client *client, int page,
+				  int reg, u16 word)
+{
+	int ret;
+
+	ret = pmbus_write_word_data(client, page, reg, word);
+	/* TODO - Define new PMBUS virtual register entries for these */
+
+	return ret;
+}
+
+#if IS_ENABLED(CONFIG_SENSORS_TPS544_REGULATOR)
+static int tps544_regulator_get_voltage(struct regulator_dev *rdev)
+{
+	struct device *dev = rdev_get_dev(rdev);
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	int page = 0;
+
+	return pmbus_read_word_data(client, page, 0xff, PMBUS_READ_VOUT);
+}
+
+static int tps544_regulator_set_voltage(struct regulator_dev *rdev, int min_uV,
+					int max_uV, unsigned int *selector)
+{
+	struct device *dev = rdev_get_dev(rdev);
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tps544_data *data = to_tps544_data(info);
+	int index, page = 0;
+	u16 vout;
+
+	/* voltage will be set close to min value requested */
+	vout = (u16)((min_uV * 512) / 1000000);
+
+	/* Check voltage bucket */
+	if (min_uV >= tps544_vout[2].vol)
+		index = 2;
+	else if (min_uV >= tps544_vout[1].vol)
+		index = 1;
+	else if (min_uV >= tps544_vout[0].vol)
+		index = 0;
+	else
+		return -EINVAL;
+
+	pmbus_write_word_data(client, page, PMBUS_VOUT_SCALE_LOOP,
+			      tps544_vout[index].vloop);
+	/* Use delay after setting scale loop; this is derived from testing */
+	msleep(2000);
+	pmbus_write_word_data(client, page, PMBUS_VOUT_OV_FAULT_LIMIT,
+			      tps544_vout[index].v_ovfault);
+	pmbus_write_word_data(client, page, PMBUS_VOUT_OV_WARN_LIMIT,
+			      tps544_vout[index].v_ovwarn);
+	pmbus_write_word_data(client, page, PMBUS_VOUT_MAX,
+			      tps544_vout[index].vmax);
+	pmbus_write_word_data(client, page, PMBUS_VOUT_COMMAND, vout);
+	tps544_write_word_data(client, page, TPS544_MFR_VOUT_MIN,
+			       tps544_vout[index].mfr_vmin);
+	pmbus_write_word_data(client, page, PMBUS_VOUT_UV_WARN_LIMIT,
+			      tps544_vout[index].v_uvwarn);
+	pmbus_write_word_data(client, page, PMBUS_VOUT_UV_FAULT_LIMIT,
+			      tps544_vout[index].v_uvfault);
+
+	data->vout_min[page] = min_uV;
+	data->vout_max[page] = max_uV;
+
+	return 0;
+}
+
+static ssize_t tps544_setv_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct regulator_dev *rdev = dev_get_drvdata(dev);
+	int vout;
+
+	vout = tps544_regulator_get_voltage(rdev) * TPS544_VOUTREAD_MULTIPLIER;
+	return sprintf(buf, "%d\n", vout);
+}
+
+static ssize_t tps544_setv_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	struct regulator_dev *rdev = dev_get_drvdata(dev);
+	int val;
+	int err;
+
+	err = kstrtoint(buf, 0, &val);
+	if (err)
+		return err;
+	if (val > TPS544_VOUT_LIMIT)
+		return -EINVAL;
+
+	err = tps544_regulator_set_voltage(rdev, val, val, NULL);
+	if (err)
+		return err;
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(tps544_setv);
+
+static ssize_t tps544_restorev_store(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	int err;
+
+	err = pmbus_write_byte(client, 0, TPS544_MFR_RESTORE_DEF_ALL);
+	if (err)
+		return err;
+
+	return count;
+}
+
+static DEVICE_ATTR_WO(tps544_restorev);
+
+static ssize_t tps544_geti_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	u16 reg_iout;
+
+	reg_iout = pmbus_read_word_data(client, 0, 0xff, PMBUS_READ_IOUT) &
+			TPS544_IOUTREAD_MASK;
+
+	return sprintf(buf, "%d\n", reg_iout * TPS544_IOUTREAD_MULTIPLIER);
+}
+
+static DEVICE_ATTR_RO(tps544_geti);
+
+static ssize_t tps544_setcali_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	int reg_cali;
+
+	reg_cali = pmbus_read_word_data(client, 0, 0xff, TPS544_MFR_IOUT_CAL_OFFSET);
+
+	return sprintf(buf, "Current: 0x%x; Set value in hex to calibrate\n",
+		       reg_cali);
+}
+
+static ssize_t tps544_setcali_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	u16 val;
+	int err;
+
+	err = kstrtou16(buf, 0x0, &val);
+	if (err)
+		return err;
+
+	err = pmbus_write_word_data(client, 0, TPS544_MFR_IOUT_CAL_OFFSET, val);
+	if (err)
+		return err;
+
+	return (ssize_t)count;
+}
+
+static DEVICE_ATTR_RW(tps544_setcali);
+
+static struct attribute *reg_attrs[] = {
+	&dev_attr_tps544_setv.attr,
+	&dev_attr_tps544_restorev.attr,
+	&dev_attr_tps544_geti.attr,
+	&dev_attr_tps544_setcali.attr,
+	NULL,
+};
+
+ATTRIBUTE_GROUPS(reg);
+
+static const struct regulator_desc tps544_reg_desc[] = {
+	PMBUS_REGULATOR("vout", 0),
+};
+#endif /* CONFIG_SENSORS_TPS544_REGULATOR */
+
+static int tps544_probe(struct i2c_client *client)
+{
+	unsigned int i;
+	struct device *dev = &client->dev;
+	struct tps544_data *data;
+	struct pmbus_driver_info *info;
+#if IS_ENABLED(CONFIG_SENSORS_TPS544_REGULATOR)
+	int ret;
+	struct regulator_dev *rdev;
+	struct regulator_config rconfig = { };
+#endif
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_READ_WORD_DATA))
+		return -ENODEV;
+
+	data = devm_kzalloc(dev, sizeof(struct tps544_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->dev = dev;
+
+	info = &data->info;
+	info->write_word_data = tps544_write_word_data;
+	/* TODO - remove these 3 hooks maybe unnecessary */
+	info->write_byte = tps544_write_byte;
+	info->read_word_data = tps544_read_word_data;
+	info->read_byte_data = tps544_read_byte_data;
+
+	for (i = 0; i < ARRAY_SIZE(data->vout_min); i++)
+		data->vout_min[i] = 0xffff;
+
+	info->pages = TPS544_NUM_PAGES;
+	info->func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT;
+
+#if IS_ENABLED(CONFIG_SENSORS_TPS544_REGULATOR)
+	rconfig.dev = dev;
+	rconfig.driver_data = data;
+	info->num_regulators = info->pages;
+	info->reg_desc = tps544_reg_desc;
+	if (info->num_regulators > (int)ARRAY_SIZE(tps544_reg_desc)) {
+		dev_err(&client->dev, "num_regulators too large!");
+		info->num_regulators = ARRAY_SIZE(tps544_reg_desc);
+	}
+
+	rdev = devm_regulator_register(dev, tps544_reg_desc, &rconfig);
+	if (IS_ERR(rdev)) {
+		dev_err(dev, "Failed to register %s regulator\n",
+			info->reg_desc[0].name);
+		return (int)PTR_ERR(rdev);
+	}
+
+	ret = sysfs_create_groups(&rdev->dev.kobj, reg_groups);
+	if (ret)
+		return ret;
+
+	dev_set_drvdata(dev, rdev);
+#endif
+
+	return pmbus_do_probe(client, info);
+}
+
+static int tps544_remove(struct i2c_client *client)
+{
+#if IS_ENABLED(CONFIG_SENSORS_TPS544_REGULATOR)
+	struct device *dev = &client->dev;
+	struct regulator_dev *rdev = dev_get_drvdata(dev);
+
+	sysfs_remove_groups(&rdev->dev.kobj, reg_groups);
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id tps544_of_match[] = {
+	{ .compatible = "ti,tps544" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, tps544_of_match);
+#endif
+
+static const struct i2c_device_id tps544_id[] = {
+	{"tps544", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, tps544_id);
+
+static struct i2c_driver tps544_driver = {
+	.driver = {
+		.name = "tps544",
+		.of_match_table = of_match_ptr(tps544_of_match),
+	},
+	.probe_new = tps544_probe,
+	.remove = tps544_remove,
+	.id_table = tps544_id,
+};
+
+module_i2c_driver(tps544_driver);
+
+MODULE_AUTHOR("Harini Katakam");
+MODULE_DESCRIPTION("PMBus regulator driver for TPS544");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pmbus/ucd9000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pmbus/ucd9000.c
@@ -7,6 +7,7 @@
  */
 
 #include <linux/debugfs.h>
+#include <linux/delay.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
@@ -16,6 +17,7 @@
 #include <linux/i2c.h>
 #include <linux/pmbus.h>
 #include <linux/gpio/driver.h>
+#include <linux/timekeeping.h>
 #include "pmbus.h"
 
 enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd90320, ucd9090,
@@ -65,6 +67,7 @@
 	struct gpio_chip gpio;
 #endif
 	struct dentry *debugfs;
+	ktime_t write_time;
 };
 #define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info)
 
@@ -73,6 +76,73 @@
 	u8 index;
 };
 
+/*
+ * It has been observed that the UCD90320 randomly fails register access when
+ * doing another access right on the back of a register write. To mitigate this
+ * make sure that there is a minimum delay between a write access and the
+ * following access. The 500 is based on experimental data. At a delay of
+ * 350us the issue seems to go away. Add a bit of extra margin to allow for
+ * system to system differences.
+ */
+#define UCD90320_WAIT_DELAY_US 500
+
+static inline void ucd90320_wait(const struct ucd9000_data *data)
+{
+	s64 delta = ktime_us_delta(ktime_get(), data->write_time);
+
+	if (delta < UCD90320_WAIT_DELAY_US)
+		udelay(UCD90320_WAIT_DELAY_US - delta);
+}
+
+static int ucd90320_read_word_data(struct i2c_client *client, int page,
+				   int phase, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct ucd9000_data *data = to_ucd9000_data(info);
+
+	if (reg >= PMBUS_VIRT_BASE)
+		return -ENXIO;
+
+	ucd90320_wait(data);
+	return pmbus_read_word_data(client, page, phase, reg);
+}
+
+static int ucd90320_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct ucd9000_data *data = to_ucd9000_data(info);
+
+	ucd90320_wait(data);
+	return pmbus_read_byte_data(client, page, reg);
+}
+
+static int ucd90320_write_word_data(struct i2c_client *client, int page,
+				    int reg, u16 word)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct ucd9000_data *data = to_ucd9000_data(info);
+	int ret;
+
+	ucd90320_wait(data);
+	ret = pmbus_write_word_data(client, page, reg, word);
+	data->write_time = ktime_get();
+
+	return ret;
+}
+
+static int ucd90320_write_byte(struct i2c_client *client, int page, u8 value)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct ucd9000_data *data = to_ucd9000_data(info);
+	int ret;
+
+	ucd90320_wait(data);
+	ret = pmbus_write_byte(client, page, value);
+	data->write_time = ktime_get();
+
+	return ret;
+}
+
 static int ucd9000_get_fan_config(struct i2c_client *client, int fan)
 {
 	int fan_config = 0;
@@ -598,6 +668,11 @@
 		info->read_byte_data = ucd9000_read_byte_data;
 		info->func[0] |= PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12
 		  | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
+	} else if (mid->driver_data == ucd90320) {
+		info->read_byte_data = ucd90320_read_byte_data;
+		info->read_word_data = ucd90320_read_word_data;
+		info->write_byte = ucd90320_write_byte;
+		info->write_word_data = ucd90320_write_word_data;
 	}
 
 	ucd9000_probe_gpio(client, mid, data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/pwm-fan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/pwm-fan.c
@@ -336,8 +336,6 @@
 			return ret;
 	}
 
-	ctx->pwm_value = MAX_PWM;
-
 	pwm_init_state(ctx->pwm, &ctx->pwm_state);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/sch56xx-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/sch56xx-common.c
@@ -422,7 +422,7 @@
 	data->wddev.max_timeout = 255 * 60;
 	watchdog_set_nowayout(&data->wddev, nowayout);
 	if (output_enable & SCH56XX_WDOG_OUTPUT_ENABLE)
-		set_bit(WDOG_ACTIVE, &data->wddev.status);
+		set_bit(WDOG_HW_RUNNING, &data->wddev.status);
 
 	/* Since the watchdog uses a downcounter there is no register to read
 	   the BIOS set timeout from (if any was set at all) ->
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/sht15.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/sht15.c
@@ -1020,25 +1020,20 @@
 static int sht15_remove(struct platform_device *pdev)
 {
 	struct sht15_data *data = platform_get_drvdata(pdev);
+	int ret;
 
-	/*
-	 * Make sure any reads from the device are done and
-	 * prevent new ones beginning
-	 */
-	mutex_lock(&data->read_lock);
-	if (sht15_soft_reset(data)) {
-		mutex_unlock(&data->read_lock);
-		return -EFAULT;
-	}
 	hwmon_device_unregister(data->hwmon_dev);
 	sysfs_remove_group(&pdev->dev.kobj, &sht15_attr_group);
+
+	ret = sht15_soft_reset(data);
+	if (ret)
+		dev_err(&pdev->dev, "Failed to reset device (%pe)\n", ERR_PTR(ret));
+
 	if (!IS_ERR(data->reg)) {
 		regulator_unregister_notifier(data->reg, &data->nb);
 		regulator_disable(data->reg);
 	}
 
-	mutex_unlock(&data->read_lock);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/sht4x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/sht4x.c
@@ -129,7 +129,7 @@
 
 static ssize_t sht4x_interval_write(struct sht4x_data *data, long val)
 {
-	data->update_interval = clamp_val(val, SHT4X_MIN_POLL_INTERVAL, UINT_MAX);
+	data->update_interval = clamp_val(val, SHT4X_MIN_POLL_INTERVAL, INT_MAX);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/shtc1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/shtc1.c
@@ -238,7 +238,7 @@
 
 	if (np) {
 		data->setup.blocking_io = of_property_read_bool(np, "sensirion,blocking-io");
-		data->setup.high_precision = !of_property_read_bool(np, "sensicon,low-precision");
+		data->setup.high_precision = !of_property_read_bool(np, "sensirion,low-precision");
 	} else {
 		if (client->dev.platform_data)
 			data->setup = *(struct shtc1_platform_data *)dev->platform_data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/tmp401.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/tmp401.c
@@ -730,10 +730,21 @@
 	return 0;
 }
 
+static const struct of_device_id __maybe_unused tmp4xx_of_match[] = {
+	{ .compatible = "ti,tmp401", },
+	{ .compatible = "ti,tmp411", },
+	{ .compatible = "ti,tmp431", },
+	{ .compatible = "ti,tmp432", },
+	{ .compatible = "ti,tmp435", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, tmp4xx_of_match);
+
 static struct i2c_driver tmp401_driver = {
 	.class		= I2C_CLASS_HWMON,
 	.driver = {
 		.name	= "tmp401",
+		.of_match_table = of_match_ptr(tmp4xx_of_match),
 	},
 	.probe_new	= tmp401_probe,
 	.id_table	= tmp401_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/tmp513.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/tmp513.c
@@ -19,15 +19,20 @@
  * the Free Software Foundation; version 2 of the License.
  */
 
+#include <linux/bitops.h>
+#include <linux/bug.h>
+#include <linux/device.h>
 #include <linux/err.h>
 #include <linux/hwmon.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
-#include <linux/kernel.h>
+#include <linux/math.h>
 #include <linux/module.h>
+#include <linux/property.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
-#include <linux/util_macros.h>
+#include <linux/types.h>
+#include <linux/units.h>
 
 // Common register definition
 #define TMP51X_SHUNT_CONFIG		0x00
@@ -100,8 +105,8 @@
 #define TMP51X_REMOTE_TEMP_LIMIT_2_POS		8
 #define TMP513_REMOTE_TEMP_LIMIT_3_POS		7
 
-#define TMP51X_VBUS_RANGE_32V		32000000
-#define TMP51X_VBUS_RANGE_16V		16000000
+#define TMP51X_VBUS_RANGE_32V		(32 * MICRO)
+#define TMP51X_VBUS_RANGE_16V		(16 * MICRO)
 
 // Max and Min value
 #define MAX_BUS_VOLTAGE_32_LIMIT	32764
@@ -173,7 +178,7 @@
 	struct regmap *regmap;
 };
 
-// Set the shift based on the gain 8=4, 4=3, 2=2, 1=1
+// Set the shift based on the gain: 8 -> 1, 4 -> 2, 2 -> 3, 1 -> 4
 static inline u8 tmp51x_get_pga_shift(struct tmp51x_data *data)
 {
 	return 5 - ffs(data->pga_gain);
@@ -195,8 +200,11 @@
 		 * 2's complement number shifted by one to four depending
 		 * on the pga gain setting. 1lsb = 10uV
 		 */
-		*val = sign_extend32(regval, 17 - tmp51x_get_pga_shift(data));
-		*val = DIV_ROUND_CLOSEST(*val * 10000, data->shunt_uohms);
+		*val = sign_extend32(regval,
+				     reg == TMP51X_SHUNT_CURRENT_RESULT ?
+				     16 - tmp51x_get_pga_shift(data) : 15);
+		*val = DIV_ROUND_CLOSEST(*val * 10 * (long)MILLI, (long)data->shunt_uohms);
+
 		break;
 	case TMP51X_BUS_VOLTAGE_RESULT:
 	case TMP51X_BUS_VOLTAGE_H_LIMIT:
@@ -211,8 +219,8 @@
 		break;
 	case TMP51X_BUS_CURRENT_RESULT:
 		// Current = (ShuntVoltage * CalibrationRegister) / 4096
-		*val = sign_extend32(regval, 16) * data->curr_lsb_ua;
-		*val = DIV_ROUND_CLOSEST(*val, 1000);
+		*val = sign_extend32(regval, 15) * (long)data->curr_lsb_ua;
+		*val = DIV_ROUND_CLOSEST(*val, (long)MILLI);
 		break;
 	case TMP51X_LOCAL_TEMP_RESULT:
 	case TMP51X_REMOTE_TEMP_RESULT_1:
@@ -223,7 +231,7 @@
 	case TMP51X_REMOTE_TEMP_LIMIT_2:
 	case TMP513_REMOTE_TEMP_LIMIT_3:
 		// 1lsb = 0.0625 degrees centigrade
-		*val = sign_extend32(regval, 16) >> TMP51X_TEMP_SHIFT;
+		*val = sign_extend32(regval, 15) >> TMP51X_TEMP_SHIFT;
 		*val = DIV_ROUND_CLOSEST(*val * 625, 10);
 		break;
 	case TMP51X_N_FACTOR_AND_HYST_1:
@@ -252,7 +260,7 @@
 		 * The user enter current value and we convert it to
 		 * voltage. 1lsb = 10uV
 		 */
-		val = DIV_ROUND_CLOSEST(val * data->shunt_uohms, 10000);
+		val = DIV_ROUND_CLOSEST(val * (long)data->shunt_uohms, 10 * (long)MILLI);
 		max_val = U16_MAX >> tmp51x_get_pga_shift(data);
 		regval = clamp_val(val, -max_val, max_val);
 		break;
@@ -434,7 +442,7 @@
 
 	switch (type) {
 	case hwmon_temp:
-		if (data->id == tmp512 && channel == 4)
+		if (data->id == tmp512 && channel == 3)
 			return 0;
 		switch (attr) {
 		case hwmon_temp_input:
@@ -542,18 +550,16 @@
 	if (data->shunt_uohms == 0)
 		return regmap_write(data->regmap, TMP51X_SHUNT_CALIBRATION, 0);
 
-	max_curr_ma = DIV_ROUND_CLOSEST_ULL(vshunt_max * 1000 * 1000,
-					    data->shunt_uohms);
+	max_curr_ma = DIV_ROUND_CLOSEST_ULL(vshunt_max * MICRO, data->shunt_uohms);
 
 	/*
 	 * Calculate the minimal bit resolution for the current and the power.
 	 * Those values will be used during register interpretation.
 	 */
-	data->curr_lsb_ua = DIV_ROUND_CLOSEST_ULL(max_curr_ma * 1000, 32767);
+	data->curr_lsb_ua = DIV_ROUND_CLOSEST_ULL(max_curr_ma * MILLI, 32767);
 	data->pwr_lsb_uw = 20 * data->curr_lsb_ua;
 
-	div = DIV_ROUND_CLOSEST_ULL(data->curr_lsb_ua * data->shunt_uohms,
-				    1000 * 1000);
+	div = DIV_ROUND_CLOSEST_ULL(data->curr_lsb_ua * data->shunt_uohms, MICRO);
 
 	return regmap_write(data->regmap, TMP51X_SHUNT_CALIBRATION,
 			    DIV_ROUND_CLOSEST(40960, div));
@@ -628,9 +634,9 @@
 	} else if (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_16V) {
 		data->shunt_config &= ~TMP51X_BUS_VOLTAGE_MASK;
 	} else {
-		dev_err(dev, "ti,bus-range-microvolt is invalid: %u\n",
-			data->vbus_range_uvolt);
-		return -EINVAL;
+		return dev_err_probe(dev, -EINVAL,
+				     "ti,bus-range-microvolt is invalid: %u\n",
+				     data->vbus_range_uvolt);
 	}
 	return 0;
 }
@@ -646,8 +652,8 @@
 	} else if (data->pga_gain == 1) {
 		data->shunt_config |= CURRENT_SENSE_VOLTAGE_40_MASK;
 	} else {
-		dev_err(dev, "ti,pga-gain is invalid: %u\n", data->pga_gain);
-		return -EINVAL;
+		return dev_err_probe(dev, -EINVAL,
+				     "ti,pga-gain is invalid: %u\n", data->pga_gain);
 	}
 	return 0;
 }
@@ -679,10 +685,10 @@
 		memcpy(data->nfactor, nfactor, (data->id == tmp513) ? 3 : 2);
 
 	// Check if shunt value is compatible with pga-gain
-	if (data->shunt_uohms > data->pga_gain * 40 * 1000 * 1000) {
-		dev_err(dev, "shunt-resistor: %u too big for pga_gain: %u\n",
-			data->shunt_uohms, data->pga_gain);
-		return -EINVAL;
+	if (data->shunt_uohms > data->pga_gain * 40 * MICRO) {
+		return dev_err_probe(dev, -EINVAL,
+				     "shunt-resistor: %u too big for pga_gain: %u\n",
+				     data->shunt_uohms, data->pga_gain);
 	}
 
 	return 0;
@@ -726,22 +732,17 @@
 		data->id = i2c_match_id(tmp51x_id, client)->driver_data;
 
 	ret = tmp51x_configure(dev, data);
-	if (ret < 0) {
-		dev_err(dev, "error configuring the device: %d\n", ret);
-		return ret;
-	}
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "error configuring the device\n");
 
 	data->regmap = devm_regmap_init_i2c(client, &tmp51x_regmap_config);
-	if (IS_ERR(data->regmap)) {
-		dev_err(dev, "failed to allocate register map\n");
-		return PTR_ERR(data->regmap);
-	}
+	if (IS_ERR(data->regmap))
+		return dev_err_probe(dev, PTR_ERR(data->regmap),
+				     "failed to allocate register map\n");
 
 	ret = tmp51x_init(data);
-	if (ret < 0) {
-		dev_err(dev, "error configuring the device: %d\n", ret);
-		return -ENODEV;
-	}
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "error configuring the device\n");
 
 	hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
 							 data,
@@ -758,7 +759,7 @@
 static struct i2c_driver tmp51x_driver = {
 	.driver = {
 		.name	= "tmp51x",
-		.of_match_table = of_match_ptr(tmp51x_of_match),
+		.of_match_table = tmp51x_of_match,
 	},
 	.probe_new	= tmp51x_probe,
 	.id_table	= tmp51x_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/tps23861.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/tps23861.c
@@ -132,7 +132,7 @@
 	if (err < 0)
 		return err;
 
-	*val = (regval * TEMPERATURE_LSB) - 20000;
+	*val = ((long)regval * TEMPERATURE_LSB) - 20000;
 
 	return 0;
 }
@@ -489,18 +489,20 @@
 
 static int tps23861_port_resistance(struct tps23861_data *data, int port)
 {
-	u16 regval;
+	unsigned int raw_val;
+	__le16 regval;
 
 	regmap_bulk_read(data->regmap,
 			 PORT_1_RESISTANCE_LSB + PORT_N_RESISTANCE_LSB_OFFSET * (port - 1),
 			 &regval,
 			 2);
 
-	switch (FIELD_GET(PORT_RESISTANCE_RSN_MASK, regval)) {
+	raw_val = le16_to_cpu(regval);
+	switch (FIELD_GET(PORT_RESISTANCE_RSN_MASK, raw_val)) {
 	case PORT_RESISTANCE_RSN_OTHER:
-		return (FIELD_GET(PORT_RESISTANCE_MASK, regval) * RESISTANCE_LSB) / 10000;
+		return (FIELD_GET(PORT_RESISTANCE_MASK, raw_val) * RESISTANCE_LSB) / 10000;
 	case PORT_RESISTANCE_RSN_LOW:
-		return (FIELD_GET(PORT_RESISTANCE_MASK, regval) * RESISTANCE_LSB_LOW) / 10000;
+		return (FIELD_GET(PORT_RESISTANCE_MASK, raw_val) * RESISTANCE_LSB_LOW) / 10000;
 	case PORT_RESISTANCE_RSN_SHORT:
 	case PORT_RESISTANCE_RSN_OPEN:
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/w83627ehf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/w83627ehf.c
@@ -895,7 +895,7 @@
 	if (err < 0)
 		return err;
 
-	val = clamp_val(DIV_ROUND_CLOSEST(val, 1000), 0, 127);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, 0, 127000), 1000);
 
 	mutex_lock(&data->update_lock);
 	data->target_temp[nr] = val;
@@ -920,7 +920,7 @@
 		return err;
 
 	/* Limit the temp to 0C - 15C */
-	val = clamp_val(DIV_ROUND_CLOSEST(val, 1000), 0, 15);
+	val = DIV_ROUND_CLOSEST(clamp_val(val, 0, 15000), 1000);
 
 	mutex_lock(&data->update_lock);
 	reg = w83627ehf_read_value(data, W83627EHF_REG_TOLERANCE[nr]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwmon/xgene-hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwmon/xgene-hwmon.c
@@ -719,7 +719,7 @@
 			goto out;
 		}
 
-		if (!ctx->pcc_comm_addr) {
+		if (IS_ERR_OR_NULL(ctx->pcc_comm_addr)) {
 			dev_err(&pdev->dev,
 				"Failed to ioremap PCC comm region\n");
 			rc = -ENOMEM;
@@ -768,6 +768,7 @@
 {
 	struct xgene_hwmon_dev *ctx = platform_get_drvdata(pdev);
 
+	cancel_work_sync(&ctx->workq);
 	hwmon_device_unregister(ctx->hwmon_dev);
 	kfifo_free(&ctx->async_msg_fifo);
 	if (acpi_disabled)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwspinlock/hwspinlock_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwspinlock/hwspinlock_core.c
@@ -303,6 +303,34 @@
 EXPORT_SYMBOL_GPL(__hwspin_unlock);
 
 /**
+ * hwspin_lock_bust() - bust a specific hwspinlock
+ * @hwlock: a previously-acquired hwspinlock which we want to bust
+ * @id: identifier of the remote lock holder, if applicable
+ *
+ * This function will bust a hwspinlock that was previously acquired as
+ * long as the current owner of the lock matches the id given by the caller.
+ *
+ * Context: Process context.
+ *
+ * Returns: 0 on success, or -EINVAL if the hwspinlock does not exist, or
+ * the bust operation fails, and -EOPNOTSUPP if the bust operation is not
+ * defined for the hwspinlock.
+ */
+int hwspin_lock_bust(struct hwspinlock *hwlock, unsigned int id)
+{
+	if (WARN_ON(!hwlock))
+		return -EINVAL;
+
+	if (!hwlock->bank->ops->bust) {
+		pr_err("bust operation not defined\n");
+		return -EOPNOTSUPP;
+	}
+
+	return hwlock->bank->ops->bust(hwlock, id);
+}
+EXPORT_SYMBOL_GPL(hwspin_lock_bust);
+
+/**
  * of_hwspin_lock_simple_xlate - translate hwlock_spec to return a lock id
  * @bank: the hwspinlock device bank
  * @hwlock_spec: hwlock specifier as found in the device tree
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwspinlock/hwspinlock_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwspinlock/hwspinlock_internal.h
@@ -21,6 +21,8 @@
  * @trylock: make a single attempt to take the lock. returns 0 on
  *	     failure and true on success. may _not_ sleep.
  * @unlock:  release the lock. always succeed. may _not_ sleep.
+ * @bust:    optional, platform-specific bust handler, called by hwspinlock
+ *	     core to bust a specific lock.
  * @relax:   optional, platform-specific relax handler, called by hwspinlock
  *	     core while spinning on a lock, between two successive
  *	     invocations of @trylock. may _not_ sleep.
@@ -28,6 +30,7 @@
 struct hwspinlock_ops {
 	int (*trylock)(struct hwspinlock *lock);
 	void (*unlock)(struct hwspinlock *lock);
+	int (*bust)(struct hwspinlock *lock, unsigned int id);
 	void (*relax)(struct hwspinlock *lock);
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwspinlock/qcom_hwspinlock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwspinlock/qcom_hwspinlock.c
@@ -105,7 +105,7 @@
 	.reg_bits		= 32,
 	.reg_stride		= 4,
 	.val_bits		= 32,
-	.max_register		= 0x40000,
+	.max_register		= 0x20000,
 	.fast_io		= true,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-catu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-catu.c
@@ -267,7 +267,7 @@
 	 * Each table can address upto 1MB and we can have
 	 * CATU_PAGES_PER_SYSPAGE tables in a system page.
 	 */
-	nr_tpages = DIV_ROUND_UP(size, SZ_1M) / CATU_PAGES_PER_SYSPAGE;
+	nr_tpages = DIV_ROUND_UP(size, CATU_PAGES_PER_SYSPAGE * SZ_1M);
 	catu_table = tmc_alloc_sg_table(catu_dev, node, nr_tpages,
 					size >> PAGE_SHIFT, pages);
 	if (IS_ERR(catu_table))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-core.c
@@ -1382,7 +1382,7 @@
 			continue;
 		conn->child_dev =
 			coresight_find_csdev_by_fwnode(conn->child_fwnode);
-		if (conn->child_dev) {
+		if (conn->child_dev && conn->child_dev->has_conns_grp) {
 			ret = coresight_make_links(csdev, conn,
 						   conn->child_dev);
 			if (ret)
@@ -1421,12 +1421,8 @@
 		if (csdev->dev.fwnode == conn->child_fwnode) {
 			iterator->orphan = true;
 			coresight_remove_links(iterator, conn);
-			/*
-			 * Drop the reference to the handle for the remote
-			 * device acquired in parsing the connections from
-			 * platform data.
-			 */
-			fwnode_handle_put(conn->child_fwnode);
+
+			conn->child_dev = NULL;
 			/* No need to continue */
 			break;
 		}
@@ -1574,6 +1570,7 @@
 	int nr_refcnts = 1;
 	atomic_t *refcnts = NULL;
 	struct coresight_device *csdev;
+	bool registered = false;
 
 	csdev = kzalloc(sizeof(*csdev), GFP_KERNEL);
 	if (!csdev) {
@@ -1594,7 +1591,8 @@
 	refcnts = kcalloc(nr_refcnts, sizeof(*refcnts), GFP_KERNEL);
 	if (!refcnts) {
 		ret = -ENOMEM;
-		goto err_free_csdev;
+		kfree(csdev);
+		goto err_out;
 	}
 
 	csdev->refcnt = refcnts;
@@ -1619,6 +1617,13 @@
 	csdev->dev.fwnode = fwnode_handle_get(dev_fwnode(desc->dev));
 	dev_set_name(&csdev->dev, "%s", desc->name);
 
+	/*
+	 * Make sure the device registration and the connection fixup
+	 * are synchronised, so that we don't see uninitialised devices
+	 * on the coresight bus while trying to resolve the connections.
+	 */
+	mutex_lock(&coresight_mutex);
+
 	ret = device_register(&csdev->dev);
 	if (ret) {
 		put_device(&csdev->dev);
@@ -1626,7 +1631,7 @@
 		 * All resources are free'd explicitly via
 		 * coresight_device_release(), triggered from put_device().
 		 */
-		goto err_out;
+		goto out_unlock;
 	}
 
 	if (csdev->type == CORESIGHT_DEV_TYPE_SINK ||
@@ -1641,11 +1646,11 @@
 			 * from put_device(), which is in turn called from
 			 * function device_unregister().
 			 */
-			goto err_out;
+			goto out_unlock;
 		}
 	}
-
-	mutex_lock(&coresight_mutex);
+	/* Device is now registered */
+	registered = true;
 
 	ret = coresight_create_conns_sysfs_group(csdev);
 	if (!ret)
@@ -1655,16 +1660,18 @@
 	if (!ret && cti_assoc_ops && cti_assoc_ops->add)
 		cti_assoc_ops->add(csdev);
 
+out_unlock:
 	mutex_unlock(&coresight_mutex);
-	if (ret) {
+	/* Success */
+	if (!ret)
+		return csdev;
+
+	/* Unregister the device if needed */
+	if (registered) {
 		coresight_unregister(csdev);
 		return ERR_PTR(ret);
 	}
 
-	return csdev;
-
-err_free_csdev:
-	kfree(csdev);
 err_out:
 	/* Cleanup the connection information */
 	coresight_release_platform_data(NULL, desc->pdata);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-cpu-debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-cpu-debug.c
@@ -380,9 +380,10 @@
 	int cpu;
 	struct debug_drvdata *drvdata;
 
-	mutex_lock(&debug_lock);
+	/* Bail out if we can't acquire the mutex or the functionality is off */
+	if (!mutex_trylock(&debug_lock))
+		return NOTIFY_DONE;
 
-	/* Bail out if the functionality is disabled */
 	if (!debug_enable)
 		goto skip_dump;
 
@@ -401,7 +402,7 @@
 
 skip_dump:
 	mutex_unlock(&debug_lock);
-	return 0;
+	return NOTIFY_DONE;
 }
 
 static struct notifier_block debug_notifier = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-cti-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-cti-core.c
@@ -90,11 +90,9 @@
 static int cti_enable_hw(struct cti_drvdata *drvdata)
 {
 	struct cti_config *config = &drvdata->config;
-	struct device *dev = &drvdata->csdev->dev;
 	unsigned long flags;
 	int rc = 0;
 
-	pm_runtime_get_sync(dev->parent);
 	spin_lock_irqsave(&drvdata->spinlock, flags);
 
 	/* no need to do anything if enabled or unpowered*/
@@ -119,7 +117,6 @@
 	/* cannot enable due to error */
 cti_err_not_enabled:
 	spin_unlock_irqrestore(&drvdata->spinlock, flags);
-	pm_runtime_put(dev->parent);
 	return rc;
 }
 
@@ -153,11 +150,17 @@
 static int cti_disable_hw(struct cti_drvdata *drvdata)
 {
 	struct cti_config *config = &drvdata->config;
-	struct device *dev = &drvdata->csdev->dev;
 	struct coresight_device *csdev = drvdata->csdev;
+	int ret = 0;
 
 	spin_lock(&drvdata->spinlock);
 
+	/* don't allow negative refcounts, return an error */
+	if (!atomic_read(&drvdata->config.enable_req_count)) {
+		ret = -EINVAL;
+		goto cti_not_disabled;
+	}
+
 	/* check refcount - disable on 0 */
 	if (atomic_dec_return(&drvdata->config.enable_req_count) > 0)
 		goto cti_not_disabled;
@@ -175,13 +178,12 @@
 	coresight_disclaim_device_unlocked(csdev);
 	CS_LOCK(drvdata->base);
 	spin_unlock(&drvdata->spinlock);
-	pm_runtime_put(dev);
-	return 0;
+	return ret;
 
 	/* not disabled this call */
 cti_not_disabled:
 	spin_unlock(&drvdata->spinlock);
-	return 0;
+	return ret;
 }
 
 void cti_write_single_reg(struct cti_drvdata *drvdata, int offset, u32 value)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-cti-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-cti-sysfs.c
@@ -108,10 +108,19 @@
 	if (ret)
 		return ret;
 
-	if (val)
+	if (val) {
+		ret = pm_runtime_resume_and_get(dev->parent);
+		if (ret)
+			return ret;
 		ret = cti_enable(drvdata->csdev);
-	else
+		if (ret)
+			pm_runtime_put(dev->parent);
+	} else {
 		ret = cti_disable(drvdata->csdev);
+		if (!ret)
+			pm_runtime_put(dev->parent);
+	}
+
 	if (ret)
 		return ret;
 	return size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-etm-perf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-etm-perf.c
@@ -830,6 +830,7 @@
 	etm_pmu.addr_filters_sync	= etm_addr_filters_sync;
 	etm_pmu.addr_filters_validate	= etm_addr_filters_validate;
 	etm_pmu.nr_addr_filters		= ETM_ADDR_CMP_MAX;
+	etm_pmu.module			= THIS_MODULE;
 
 	ret = perf_pmu_register(&etm_pmu, CORESIGHT_ETM_PMU_NAME, -1);
 	if (ret == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-etm4x-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-etm4x-core.c
@@ -384,8 +384,10 @@
 		etm4x_relaxed_write32(csa, config->vipcssctlr, TRCVIPCSSCTLR);
 	for (i = 0; i < drvdata->nrseqstate - 1; i++)
 		etm4x_relaxed_write32(csa, config->seq_ctrl[i], TRCSEQEVRn(i));
-	etm4x_relaxed_write32(csa, config->seq_rst, TRCSEQRSTEVR);
-	etm4x_relaxed_write32(csa, config->seq_state, TRCSEQSTR);
+	if (drvdata->nrseqstate) {
+		etm4x_relaxed_write32(csa, config->seq_rst, TRCSEQRSTEVR);
+		etm4x_relaxed_write32(csa, config->seq_state, TRCSEQSTR);
+	}
 	etm4x_relaxed_write32(csa, config->ext_inp, TRCEXTINSELR);
 	for (i = 0; i < drvdata->nr_cntr; i++) {
 		etm4x_relaxed_write32(csa, config->cntrldvr[i], TRCCNTRLDVRn(i));
@@ -409,7 +411,7 @@
 		if (etm4x_sspcicrn_present(drvdata, i))
 			etm4x_relaxed_write32(csa, config->ss_pe_cmp[i], TRCSSPCICRn(i));
 	}
-	for (i = 0; i < drvdata->nr_addr_cmp; i++) {
+	for (i = 0; i < drvdata->nr_addr_cmp * 2; i++) {
 		etm4x_relaxed_write64(csa, config->addr_val[i], TRCACVRn(i));
 		etm4x_relaxed_write64(csa, config->addr_acc[i], TRCACATRn(i));
 	}
@@ -949,25 +951,21 @@
 				   struct csdev_access *csa)
 {
 	u32 devarch = readl_relaxed(drvdata->base + TRCDEVARCH);
-	u32 idr1 = readl_relaxed(drvdata->base + TRCIDR1);
 
 	/*
 	 * All ETMs must implement TRCDEVARCH to indicate that
-	 * the component is an ETMv4. To support any broken
-	 * implementations we fall back to TRCIDR1 check, which
-	 * is not really reliable.
+	 * the component is an ETMv4. Even though TRCIDR1 also
+	 * contains the information, it is part of the "Trace"
+	 * register and must be accessed with the OSLK cleared,
+	 * with MMIO. But we cannot touch the OSLK until we are
+	 * sure this is an ETM. So rely only on the TRCDEVARCH.
 	 */
-	if ((devarch & ETM_DEVARCH_ID_MASK) == ETM_DEVARCH_ETMv4x_ARCH) {
-		drvdata->arch = etm_devarch_to_arch(devarch);
-	} else {
-		pr_warn("CPU%d: ETM4x incompatible TRCDEVARCH: %x, falling back to TRCIDR1\n",
-			smp_processor_id(), devarch);
-
-		if (ETM_TRCIDR1_ARCH_MAJOR(idr1) != ETM_TRCIDR1_ARCH_ETMv4)
-			return false;
-		drvdata->arch = etm_trcidr_to_arch(idr1);
+	if ((devarch & ETM_DEVARCH_ID_MASK) != ETM_DEVARCH_ETMv4x_ARCH) {
+		pr_warn_once("TRCDEVARCH doesn't match ETMv4 architecture\n");
+		return false;
 	}
 
+	drvdata->arch = etm_devarch_to_arch(devarch);
 	*csa = CSDEV_ACCESS_IOMEM(drvdata->base);
 	return true;
 }
@@ -1050,41 +1048,23 @@
 	etmidr0 = etm4x_relaxed_read32(csa, TRCIDR0);
 
 	/* INSTP0, bits[2:1] P0 tracing support field */
-	if (BMVAL(etmidr0, 1, 1) && BMVAL(etmidr0, 2, 2))
-		drvdata->instrp0 = true;
-	else
-		drvdata->instrp0 = false;
-
+	drvdata->instrp0 = !!(FIELD_GET(TRCIDR0_INSTP0_MASK, etmidr0) == 0b11);
 	/* TRCBB, bit[5] Branch broadcast tracing support bit */
-	if (BMVAL(etmidr0, 5, 5))
-		drvdata->trcbb = true;
-	else
-		drvdata->trcbb = false;
-
+	drvdata->trcbb = !!(etmidr0 & TRCIDR0_TRCBB);
 	/* TRCCOND, bit[6] Conditional instruction tracing support bit */
-	if (BMVAL(etmidr0, 6, 6))
-		drvdata->trccond = true;
-	else
-		drvdata->trccond = false;
-
+	drvdata->trccond = !!(etmidr0 & TRCIDR0_TRCCOND);
 	/* TRCCCI, bit[7] Cycle counting instruction bit */
-	if (BMVAL(etmidr0, 7, 7))
-		drvdata->trccci = true;
-	else
-		drvdata->trccci = false;
-
+	drvdata->trccci = !!(etmidr0 & TRCIDR0_TRCCCI);
 	/* RETSTACK, bit[9] Return stack bit */
-	if (BMVAL(etmidr0, 9, 9))
-		drvdata->retstack = true;
-	else
-		drvdata->retstack = false;
-
+	drvdata->retstack = !!(etmidr0 & TRCIDR0_RETSTACK);
 	/* NUMEVENT, bits[11:10] Number of events field */
-	drvdata->nr_event = BMVAL(etmidr0, 10, 11);
+	drvdata->nr_event = FIELD_GET(TRCIDR0_NUMEVENT_MASK, etmidr0);
 	/* QSUPP, bits[16:15] Q element support field */
-	drvdata->q_support = BMVAL(etmidr0, 15, 16);
+	drvdata->q_support = FIELD_GET(TRCIDR0_QSUPP_MASK, etmidr0);
+	if (drvdata->q_support)
+		drvdata->q_filt = !!(etmidr0 & TRCIDR0_QFILT);
 	/* TSSIZE, bits[28:24] Global timestamp size field */
-	drvdata->ts_size = BMVAL(etmidr0, 24, 28);
+	drvdata->ts_size = FIELD_GET(TRCIDR0_TSSIZE_MASK, etmidr0);
 
 	/* maximum size of resources */
 	etmidr2 = etm4x_relaxed_read32(csa, TRCIDR2);
@@ -1604,22 +1584,22 @@
 	state->trcccctlr = etm4x_read32(csa, TRCCCCTLR);
 	state->trcbbctlr = etm4x_read32(csa, TRCBBCTLR);
 	state->trctraceidr = etm4x_read32(csa, TRCTRACEIDR);
-	state->trcqctlr = etm4x_read32(csa, TRCQCTLR);
+	if (drvdata->q_filt)
+		state->trcqctlr = etm4x_read32(csa, TRCQCTLR);
 
 	state->trcvictlr = etm4x_read32(csa, TRCVICTLR);
 	state->trcviiectlr = etm4x_read32(csa, TRCVIIECTLR);
 	state->trcvissctlr = etm4x_read32(csa, TRCVISSCTLR);
 	if (drvdata->nr_pe_cmp)
 		state->trcvipcssctlr = etm4x_read32(csa, TRCVIPCSSCTLR);
-	state->trcvdctlr = etm4x_read32(csa, TRCVDCTLR);
-	state->trcvdsacctlr = etm4x_read32(csa, TRCVDSACCTLR);
-	state->trcvdarcctlr = etm4x_read32(csa, TRCVDARCCTLR);
 
 	for (i = 0; i < drvdata->nrseqstate - 1; i++)
 		state->trcseqevr[i] = etm4x_read32(csa, TRCSEQEVRn(i));
 
-	state->trcseqrstevr = etm4x_read32(csa, TRCSEQRSTEVR);
-	state->trcseqstr = etm4x_read32(csa, TRCSEQSTR);
+	if (drvdata->nrseqstate) {
+		state->trcseqrstevr = etm4x_read32(csa, TRCSEQRSTEVR);
+		state->trcseqstr = etm4x_read32(csa, TRCSEQSTR);
+	}
 	state->trcextinselr = etm4x_read32(csa, TRCEXTINSELR);
 
 	for (i = 0; i < drvdata->nr_cntr; i++) {
@@ -1628,7 +1608,8 @@
 		state->trccntvr[i] = etm4x_read32(csa, TRCCNTVRn(i));
 	}
 
-	for (i = 0; i < drvdata->nr_resource * 2; i++)
+	/* Resource selector pair 0 is reserved */
+	for (i = 2; i < drvdata->nr_resource * 2; i++)
 		state->trcrsctlr[i] = etm4x_read32(csa, TRCRSCTLRn(i));
 
 	for (i = 0; i < drvdata->nr_ss_cmp; i++) {
@@ -1697,8 +1678,10 @@
 {
 	int i;
 	struct etmv4_save_state *state = drvdata->save_state;
-	struct csdev_access tmp_csa = CSDEV_ACCESS_IOMEM(drvdata->base);
-	struct csdev_access *csa = &tmp_csa;
+	struct csdev_access *csa = &drvdata->csdev->access;
+
+	if (WARN_ON(!drvdata->csdev))
+		return;
 
 	etm4_cs_unlock(drvdata, csa);
 	etm4x_relaxed_write32(csa, state->trcclaimset, TRCCLAIMSET);
@@ -1717,22 +1700,22 @@
 	etm4x_relaxed_write32(csa, state->trcccctlr, TRCCCCTLR);
 	etm4x_relaxed_write32(csa, state->trcbbctlr, TRCBBCTLR);
 	etm4x_relaxed_write32(csa, state->trctraceidr, TRCTRACEIDR);
-	etm4x_relaxed_write32(csa, state->trcqctlr, TRCQCTLR);
+	if (drvdata->q_filt)
+		etm4x_relaxed_write32(csa, state->trcqctlr, TRCQCTLR);
 
 	etm4x_relaxed_write32(csa, state->trcvictlr, TRCVICTLR);
 	etm4x_relaxed_write32(csa, state->trcviiectlr, TRCVIIECTLR);
 	etm4x_relaxed_write32(csa, state->trcvissctlr, TRCVISSCTLR);
 	if (drvdata->nr_pe_cmp)
 		etm4x_relaxed_write32(csa, state->trcvipcssctlr, TRCVIPCSSCTLR);
-	etm4x_relaxed_write32(csa, state->trcvdctlr, TRCVDCTLR);
-	etm4x_relaxed_write32(csa, state->trcvdsacctlr, TRCVDSACCTLR);
-	etm4x_relaxed_write32(csa, state->trcvdarcctlr, TRCVDARCCTLR);
 
 	for (i = 0; i < drvdata->nrseqstate - 1; i++)
 		etm4x_relaxed_write32(csa, state->trcseqevr[i], TRCSEQEVRn(i));
 
-	etm4x_relaxed_write32(csa, state->trcseqrstevr, TRCSEQRSTEVR);
-	etm4x_relaxed_write32(csa, state->trcseqstr, TRCSEQSTR);
+	if (drvdata->nrseqstate) {
+		etm4x_relaxed_write32(csa, state->trcseqrstevr, TRCSEQRSTEVR);
+		etm4x_relaxed_write32(csa, state->trcseqstr, TRCSEQSTR);
+	}
 	etm4x_relaxed_write32(csa, state->trcextinselr, TRCEXTINSELR);
 
 	for (i = 0; i < drvdata->nr_cntr; i++) {
@@ -1741,7 +1724,8 @@
 		etm4x_relaxed_write32(csa, state->trccntvr[i], TRCCNTVRn(i));
 	}
 
-	for (i = 0; i < drvdata->nr_resource * 2; i++)
+	/* Resource selector pair 0 is reserved */
+	for (i = 2; i < drvdata->nr_resource * 2; i++)
 		etm4x_relaxed_write32(csa, state->trcrsctlr[i], TRCRSCTLRn(i));
 
 	for (i = 0; i < drvdata->nr_ss_cmp; i++) {
@@ -2020,6 +2004,9 @@
 	ret = etm4_probe(&pdev->dev, NULL, 0);
 
 	pm_runtime_put(&pdev->dev);
+	if (ret)
+		pm_runtime_disable(&pdev->dev);
+
 	return ret;
 }
 
@@ -2039,7 +2026,7 @@
 	etmdrvdata[cpu] = NULL;
 }
 
-static int __exit etm4_remove_dev(struct etmv4_drvdata *drvdata)
+static void etm4_remove_dev(struct etmv4_drvdata *drvdata)
 {
 	etm_perf_symlink(drvdata->csdev, false);
 	/*
@@ -2060,11 +2047,9 @@
 
 	cscfg_unregister_csdev(drvdata->csdev);
 	coresight_unregister(drvdata->csdev);
-
-	return 0;
 }
 
-static void __exit etm4_remove_amba(struct amba_device *adev)
+static void etm4_remove_amba(struct amba_device *adev)
 {
 	struct etmv4_drvdata *drvdata = dev_get_drvdata(&adev->dev);
 
@@ -2072,15 +2057,14 @@
 		etm4_remove_dev(drvdata);
 }
 
-static int __exit etm4_remove_platform_dev(struct platform_device *pdev)
+static int etm4_remove_platform_dev(struct platform_device *pdev)
 {
-	int ret = 0;
 	struct etmv4_drvdata *drvdata = dev_get_drvdata(&pdev->dev);
 
 	if (drvdata)
-		ret = etm4_remove_dev(drvdata);
+		etm4_remove_dev(drvdata);
 	pm_runtime_disable(&pdev->dev);
-	return ret;
+	return 0;
 }
 
 static const struct amba_id etm4_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-etm4x-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-etm4x-sysfs.c
@@ -367,8 +367,12 @@
 	mode = ETM_MODE_QELEM(config->mode);
 	/* start by clearing QE bits */
 	config->cfg &= ~(BIT(13) | BIT(14));
-	/* if supported, Q elements with instruction counts are enabled */
-	if ((mode & BIT(0)) && (drvdata->q_support & BIT(0)))
+	/*
+	 * if supported, Q elements with instruction counts are enabled.
+	 * Always set the low bit for any requested mode. Valid combos are
+	 * 0b00, 0b01 and 0b11.
+	 */
+	if (mode && drvdata->q_support)
 		config->cfg |= BIT(13);
 	/*
 	 * if supported, Q elements with and without instruction
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-etm4x.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-etm4x.h
@@ -7,6 +7,7 @@
 #define _CORESIGHT_CORESIGHT_ETM_H
 
 #include <asm/local.h>
+#include <linux/const.h>
 #include <linux/spinlock.h>
 #include <linux/types.h>
 #include "coresight-priv.h"
@@ -42,9 +43,6 @@
 #define TRCVIIECTLR			0x084
 #define TRCVISSCTLR			0x088
 #define TRCVIPCSSCTLR			0x08C
-#define TRCVDCTLR			0x0A0
-#define TRCVDSACCTLR			0x0A4
-#define TRCVDARCCTLR			0x0A8
 /* Derived resources registers */
 #define TRCSEQEVRn(n)			(0x100 + (n * 4)) /* n = 0-2 */
 #define TRCSEQRSTEVR			0x118
@@ -89,9 +87,6 @@
 /* Address Comparator registers n = 0-15 */
 #define TRCACVRn(n)			(0x400 + (n * 8))
 #define TRCACATRn(n)			(0x480 + (n * 8))
-/* Data Value Comparator Value registers, n = 0-7 */
-#define TRCDVCVRn(n)			(0x500 + (n * 16))
-#define TRCDVCMRn(n)			(0x580 + (n * 16))
 /* ContextID/Virtual ContextID comparators, n = 0-7 */
 #define TRCCIDCVRn(n)			(0x600 + (n * 8))
 #define TRCVMIDCVRn(n)			(0x640 + (n * 8))
@@ -131,6 +126,20 @@
 #define TRCRSR_TA			BIT(12)
 
 /*
+ * Bit positions of registers that are defined above, in the sysreg.h style
+ * of _MASK for multi bit fields and BIT() for single bits.
+ */
+#define TRCIDR0_INSTP0_MASK			GENMASK(2, 1)
+#define TRCIDR0_TRCBB				BIT(5)
+#define TRCIDR0_TRCCOND				BIT(6)
+#define TRCIDR0_TRCCCI				BIT(7)
+#define TRCIDR0_RETSTACK			BIT(9)
+#define TRCIDR0_NUMEVENT_MASK			GENMASK(11, 10)
+#define TRCIDR0_QFILT				BIT(14)
+#define TRCIDR0_QSUPP_MASK			GENMASK(16, 15)
+#define TRCIDR0_TSSIZE_MASK			GENMASK(28, 24)
+
+/*
  * System instructions to access ETM registers.
  * See ETMv4.4 spec ARM IHI0064F section 4.3.6 System instructions
  */
@@ -173,9 +182,6 @@
 /* List of registers accessible via System instructions */
 #define ETM4x_ONLY_SYSREG_LIST(op, val)		\
 	CASE_##op((val), TRCPROCSELR)		\
-	CASE_##op((val), TRCVDCTLR)		\
-	CASE_##op((val), TRCVDSACCTLR)		\
-	CASE_##op((val), TRCVDARCCTLR)		\
 	CASE_##op((val), TRCOSLAR)
 
 #define ETM_COMMON_SYSREG_LIST(op, val)		\
@@ -323,22 +329,6 @@
 	CASE_##op((val), TRCACATRn(13))		\
 	CASE_##op((val), TRCACATRn(14))		\
 	CASE_##op((val), TRCACATRn(15))		\
-	CASE_##op((val), TRCDVCVRn(0))		\
-	CASE_##op((val), TRCDVCVRn(1))		\
-	CASE_##op((val), TRCDVCVRn(2))		\
-	CASE_##op((val), TRCDVCVRn(3))		\
-	CASE_##op((val), TRCDVCVRn(4))		\
-	CASE_##op((val), TRCDVCVRn(5))		\
-	CASE_##op((val), TRCDVCVRn(6))		\
-	CASE_##op((val), TRCDVCVRn(7))		\
-	CASE_##op((val), TRCDVCMRn(0))		\
-	CASE_##op((val), TRCDVCMRn(1))		\
-	CASE_##op((val), TRCDVCMRn(2))		\
-	CASE_##op((val), TRCDVCMRn(3))		\
-	CASE_##op((val), TRCDVCMRn(4))		\
-	CASE_##op((val), TRCDVCMRn(5))		\
-	CASE_##op((val), TRCDVCMRn(6))		\
-	CASE_##op((val), TRCDVCMRn(7))		\
 	CASE_##op((val), TRCCIDCVRn(0))		\
 	CASE_##op((val), TRCCIDCVRn(1))		\
 	CASE_##op((val), TRCCIDCVRn(2))		\
@@ -417,7 +407,7 @@
 	({									\
 		u64 __val;							\
 										\
-		if (__builtin_constant_p((offset)))				\
+		if (__is_constexpr((offset)))					\
 			__val = read_etm4x_sysreg_const_offset((offset));	\
 		else								\
 			__val = etm4x_sysreg_read((offset), true, (_64bit));	\
@@ -668,14 +658,12 @@
  * TRCDEVARCH	- CoreSight architected register
  *                - Bits[15:12] - Major version
  *                - Bits[19:16] - Minor version
- * TRCIDR1	- ETM architected register
- *                - Bits[11:8] - Major version
- *                - Bits[7:4]  - Minor version
- * We must rely on TRCDEVARCH for the version information,
- * however we don't want to break the support for potential
- * old implementations which might not implement it. Thus
- * we fall back to TRCIDR1 if TRCDEVARCH is not implemented
- * for memory mapped components.
+ *
+ * We must rely only on TRCDEVARCH for the version information. Even though,
+ * TRCIDR1 also provides the architecture version, it is a "Trace" register
+ * and as such must be accessed only with Trace power domain ON. This may
+ * not be available at probe time.
+ *
  * Now to make certain decisions easier based on the version
  * we use an internal representation of the version in the
  * driver, as follows :
@@ -701,12 +689,6 @@
 				ETM_DEVARCH_REVISION(devarch));
 }
 
-static inline u8 etm_trcidr_to_arch(u32 trcidr1)
-{
-	return ETM_ARCH_VERSION(ETM_TRCIDR1_ARCH_MAJOR(trcidr1),
-				ETM_TRCIDR1_ARCH_MINOR(trcidr1));
-}
-
 enum etm_impdef_type {
 	ETM4_IMPDEF_HISI_CORE_COMMIT,
 	ETM4_IMPDEF_FEATURE_MAX,
@@ -828,9 +810,6 @@
 	u32	trcviiectlr;
 	u32	trcvissctlr;
 	u32	trcvipcssctlr;
-	u32	trcvdctlr;
-	u32	trcvdsacctlr;
-	u32	trcvdarcctlr;
 
 	u32	trcseqevr[ETM_MAX_SEQ_STATES];
 	u32	trcseqrstevr;
@@ -902,6 +881,7 @@
  * @os_unlock:  True if access to management registers is allowed.
  * @instrp0:	Tracing of load and store instructions
  *		as P0 elements is supported.
+ * @q_filt:	Q element filtering support, if Q elements are supported.
  * @trcbb:	Indicates if the trace unit supports branch broadcast tracing.
  * @trccond:	If the trace unit supports conditional
  *		instruction tracing.
@@ -951,7 +931,7 @@
 	u8				ctxid_size;
 	u8				vmid_size;
 	u8				ccsize;
-	u8				ccitmin;
+	u16				ccitmin;
 	u8				s_ex_level;
 	u8				ns_ex_level;
 	u8				q_support;
@@ -960,6 +940,7 @@
 	bool				boot_enable;
 	bool				os_unlock;
 	bool				instrp0;
+	bool				q_filt;
 	bool				trcbb;
 	bool				trccond;
 	bool				retstack;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-platform.c
@@ -323,8 +323,10 @@
 			continue;
 
 		ret = of_coresight_parse_endpoint(dev, ep, pdata);
-		if (ret)
+		if (ret) {
+			of_node_put(ep);
 			return ret;
+		}
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-syscfg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-syscfg.c
@@ -791,7 +791,7 @@
 
 	err = device_register(dev);
 	if (err)
-		cscfg_dev_release(dev);
+		put_device(dev);
 
 create_dev_exit_unlock:
 	mutex_unlock(&cscfg_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-tmc-etf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-tmc-etf.c
@@ -428,7 +428,7 @@
 		return -EINVAL;
 
 	/* wrap head around to the amount of space we have */
-	head = handle->head & ((buf->nr_pages << PAGE_SHIFT) - 1);
+	head = handle->head & (((unsigned long)buf->nr_pages << PAGE_SHIFT) - 1);
 
 	/* find the page to write to */
 	buf->cur = head / PAGE_SIZE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-tmc-etr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-tmc-etr.c
@@ -47,7 +47,8 @@
 };
 
 /* Convert the perf index to an offset within the ETR buffer */
-#define PERF_IDX2OFF(idx, buf)	((idx) % ((buf)->nr_pages << PAGE_SHIFT))
+#define PERF_IDX2OFF(idx, buf)		\
+		((idx) % ((unsigned long)(buf)->nr_pages << PAGE_SHIFT))
 
 /* Lower limit for ETR hardware buffer */
 #define TMC_ETR_PERF_MIN_BUF_SIZE	SZ_1M
@@ -256,6 +257,7 @@
 {
 	tmc_free_table_pages(sg_table);
 	tmc_free_data_pages(sg_table);
+	kfree(sg_table);
 }
 EXPORT_SYMBOL_GPL(tmc_free_sg_table);
 
@@ -337,7 +339,6 @@
 		rc = tmc_alloc_table_pages(sg_table);
 	if (rc) {
 		tmc_free_sg_table(sg_table);
-		kfree(sg_table);
 		return ERR_PTR(rc);
 	}
 
@@ -926,7 +927,7 @@
 
 	len = tmc_etr_buf_get_data(etr_buf, offset,
 				   CORESIGHT_BARRIER_PKT_SIZE, &bufp);
-	if (WARN_ON(len < CORESIGHT_BARRIER_PKT_SIZE))
+	if (WARN_ON(len < 0 || len < CORESIGHT_BARRIER_PKT_SIZE))
 		return -EINVAL;
 	coresight_insert_barrier_packet(bufp);
 	return offset + CORESIGHT_BARRIER_PKT_SIZE;
@@ -1232,7 +1233,7 @@
 	 * than the size requested via sysfs.
 	 */
 	if ((nr_pages << PAGE_SHIFT) > drvdata->size) {
-		etr_buf = tmc_alloc_etr_buf(drvdata, (nr_pages << PAGE_SHIFT),
+		etr_buf = tmc_alloc_etr_buf(drvdata, ((ssize_t)nr_pages << PAGE_SHIFT),
 					    0, node, NULL);
 		if (!IS_ERR(etr_buf))
 			goto done;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-tmc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-tmc.h
@@ -321,7 +321,7 @@
 static inline unsigned long
 tmc_sg_table_buf_size(struct tmc_sg_table *sg_table)
 {
-	return sg_table->data_pages.nr_pages << PAGE_SHIFT;
+	return (unsigned long)sg_table->data_pages.nr_pages << PAGE_SHIFT;
 }
 
 struct coresight_device *tmc_etr_get_catu_device(struct tmc_drvdata *drvdata);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/coresight/coresight-trbe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/coresight/coresight-trbe.c
@@ -366,7 +366,7 @@
 
 static unsigned long trbe_normal_offset(struct perf_output_handle *handle)
 {
-	struct trbe_buf *buf = perf_get_aux(handle);
+	struct trbe_buf *buf = etm_perf_sink_config(handle);
 	u64 limit = __trbe_normal_offset(handle);
 	u64 head = PERF_IDX2OFF(handle->head, buf);
 
@@ -869,6 +869,10 @@
 	if (WARN_ON(trbe_csdev))
 		return;
 
+	/* If the TRBE was not probed on the CPU, we shouldn't be here */
+	if (WARN_ON(!cpudata->drvdata))
+		return;
+
 	dev = &cpudata->drvdata->pdev->dev;
 	desc.name = devm_kasprintf(dev, GFP_KERNEL, "trbe%d", cpu);
 	if (!desc.name)
@@ -950,7 +954,9 @@
 		return -ENOMEM;
 
 	for_each_cpu(cpu, &drvdata->supported_cpus) {
-		smp_call_function_single(cpu, arm_trbe_probe_cpu, drvdata, 1);
+		/* If we fail to probe the CPU, let us defer it to hotplug callbacks */
+		if (smp_call_function_single(cpu, arm_trbe_probe_cpu, drvdata, 1))
+			continue;
 		if (cpumask_test_cpu(cpu, &drvdata->supported_cpus))
 			arm_trbe_register_coresight_cpu(drvdata, cpu);
 		if (cpumask_test_cpu(cpu, &drvdata->supported_cpus))
@@ -1024,6 +1030,7 @@
 
 static void arm_trbe_remove_cpuhp(struct trbe_drvdata *drvdata)
 {
+	cpuhp_state_remove_instance(drvdata->trbe_online, &drvdata->hotplug_node);
 	cpuhp_remove_multi_state(drvdata->trbe_online);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/intel_th/msu-sink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/intel_th/msu-sink.c
@@ -71,6 +71,9 @@
 		block = dma_alloc_coherent(priv->dev->parent->parent,
 					   PAGE_SIZE, &sg_dma_address(sg_ptr),
 					   GFP_KERNEL);
+		if (!block)
+			return -ENOMEM;
+
 		sg_set_buf(sg_ptr, block, PAGE_SIZE);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/intel_th/msu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/intel_th/msu.c
@@ -1069,6 +1069,16 @@
 static inline void msc_buffer_set_wb(struct msc *msc) {}
 #endif /* CONFIG_X86 */
 
+static struct page *msc_sg_page(struct scatterlist *sg)
+{
+	void *addr = sg_virt(sg);
+
+	if (is_vmalloc_addr(addr))
+		return vmalloc_to_page(addr);
+
+	return sg_page(sg);
+}
+
 /**
  * msc_buffer_win_alloc() - alloc a window for a multiblock mode
  * @msc:	MSC device
@@ -1139,7 +1149,7 @@
 	int i;
 
 	for_each_sg(win->sgt->sgl, sg, win->nr_segs, i) {
-		struct page *page = sg_page(sg);
+		struct page *page = msc_sg_page(sg);
 
 		page->mapping = NULL;
 		dma_free_coherent(msc_dev(win->msc)->parent->parent, PAGE_SIZE,
@@ -1403,7 +1413,7 @@
 	pgoff -= win->pgoff;
 
 	for_each_sg(win->sgt->sgl, sg, win->nr_segs, blk) {
-		struct page *page = sg_page(sg);
+		struct page *page = msc_sg_page(sg);
 		size_t pgsz = PFN_DOWN(sg->length);
 
 		if (pgoff < pgsz)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/intel_th/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/intel_th/pci.c
@@ -100,8 +100,10 @@
 		}
 
 	th = intel_th_alloc(&pdev->dev, drvdata, resource, r);
-	if (IS_ERR(th))
-		return PTR_ERR(th);
+	if (IS_ERR(th)) {
+		err = PTR_ERR(th);
+		goto err_free_irq;
+	}
 
 	th->activate   = intel_th_pci_activate;
 	th->deactivate = intel_th_pci_deactivate;
@@ -109,6 +111,10 @@
 	pci_set_master(pdev);
 
 	return 0;
+
+err_free_irq:
+	pci_free_irq_vectors(pdev);
+	return err;
 }
 
 static void intel_th_pci_remove(struct pci_dev *pdev)
@@ -279,6 +285,66 @@
 		.driver_data = (kernel_ulong_t)&intel_th_2x,
 	},
 	{
+		/* Meteor Lake-P */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x7e24),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Meteor Lake-S CPU */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0xae24),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Meteor Lake-S */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x7f26),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Raptor Lake-S */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x7a26),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Raptor Lake-S CPU */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0xa76f),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Granite Rapids */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0963),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Granite Rapids SOC */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x3256),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Sapphire Rapids SOC */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x3456),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Lunar Lake */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0xa824),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Arrow Lake */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x7724),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Panther Lake-H */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0xe324),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
+		/* Panther Lake-P/U */
+		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0xe424),
+		.driver_data = (kernel_ulong_t)&intel_th_2x,
+	},
+	{
 		/* Alder Lake CPU */
 		PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x466f),
 		.driver_data = (kernel_ulong_t)&intel_th_2x,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/hwtracing/stm/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/hwtracing/stm/core.c
@@ -868,8 +868,11 @@
 		return -ENOMEM;
 
 	stm->major = register_chrdev(0, stm_data->name, &stm_fops);
-	if (stm->major < 0)
-		goto err_free;
+	if (stm->major < 0) {
+		err = stm->major;
+		vfree(stm);
+		return err;
+	}
 
 	device_initialize(&stm->dev);
 	stm->dev.devt = MKDEV(stm->major, 0);
@@ -913,10 +916,8 @@
 err_device:
 	unregister_chrdev(stm->major, stm_data->name);
 
-	/* matches device_initialize() above */
+	/* calls stm_device_release() */
 	put_device(&stm->dev);
-err_free:
-	vfree(stm);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/Kconfig
@@ -488,7 +488,7 @@
 
 config I2C_CADENCE
 	tristate "Cadence I2C Controller"
-	depends on ARCH_ZYNQ || ARM64 || XTENSA
+	depends on ARCH_ZYNQ || ARM64 || XTENSA || COMPILE_TEST
 	help
 	  Say yes here to select Cadence I2C Host Controller. This controller is
 	  e.g. used by Xilinx Zynq.
@@ -677,7 +677,7 @@
 
 config I2C_IMX
 	tristate "IMX I2C interface"
-	depends on ARCH_MXC || ARCH_LAYERSCAPE || COLDFIRE
+	depends on ARCH_MXC || ARCH_LAYERSCAPE || COLDFIRE || COMPILE_TEST
 	select I2C_SLAVE
 	help
 	  Say Y here if you want to use the IIC bus controller on
@@ -921,7 +921,7 @@
 
 config I2C_QUP
 	tristate "Qualcomm QUP based I2C controller"
-	depends on ARCH_QCOM
+	depends on ARCH_QCOM || COMPILE_TEST
 	help
 	  If you say yes to this option, support will be included for the
 	  built-in I2C interface on the Qualcomm SoCs.
@@ -1308,6 +1308,16 @@
 	  If you have a 2019 edition board with an LTC2990 sensor at address
 	  0x4c, loading the module 'ltc2990' is sufficient to enable it.
 
+config I2C_LJCA
+	tristate "I2C functionality of INTEL La Jolla Cove Adapter"
+	depends on MFD_LJCA
+	help
+	  If you say yes to this option, I2C functionality support of INTEL
+	  La Jolla Cove Adapter (LJCA) will be included.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-ljca.
+
 config I2C_MLXCPLD
 	tristate "Mellanox I2C driver"
 	depends on X86_64 || COMPILE_TEST
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/Makefile
@@ -137,6 +137,7 @@
 obj-$(CONFIG_I2C_CROS_EC_TUNNEL)	+= i2c-cros-ec-tunnel.o
 obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
 obj-$(CONFIG_I2C_ICY)		+= i2c-icy.o
+obj-$(CONFIG_I2C_LJCA)		+= i2c-ljca.o
 obj-$(CONFIG_I2C_MLXBF)		+= i2c-mlxbf.o
 obj-$(CONFIG_I2C_MLXCPLD)	+= i2c-mlxcpld.o
 obj-$(CONFIG_I2C_OPAL)		+= i2c-opal.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-ali1535.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-ali1535.c
@@ -490,6 +490,8 @@
 
 static int ali1535_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
+	int ret;
+
 	if (ali1535_setup(dev)) {
 		dev_warn(&dev->dev,
 			"ALI1535 not detected, module not inserted.\n");
@@ -501,7 +503,15 @@
 
 	snprintf(ali1535_adapter.name, sizeof(ali1535_adapter.name),
 		"SMBus ALI1535 adapter at %04x", ali1535_offset);
-	return i2c_add_adapter(&ali1535_adapter);
+	ret = i2c_add_adapter(&ali1535_adapter);
+	if (ret)
+		goto release_region;
+
+	return 0;
+
+release_region:
+	release_region(ali1535_smba, ALI1535_SMB_IOSIZE);
+	return ret;
 }
 
 static void ali1535_remove(struct pci_dev *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-ali15x3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-ali15x3.c
@@ -473,6 +473,8 @@
 
 static int ali15x3_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
+	int ret;
+
 	if (ali15x3_setup(dev)) {
 		dev_err(&dev->dev,
 			"ALI15X3 not detected, module not inserted.\n");
@@ -484,7 +486,15 @@
 
 	snprintf(ali15x3_adapter.name, sizeof(ali15x3_adapter.name),
 		"SMBus ALI15X3 adapter at %04x", ali15x3_smba);
-	return i2c_add_adapter(&ali15x3_adapter);
+	ret = i2c_add_adapter(&ali15x3_adapter);
+	if (ret)
+		goto release_region;
+
+	return 0;
+
+release_region:
+	release_region(ali15x3_smba, ALI15X3_SMB_IOSIZE);
+	return ret;
 }
 
 static void ali15x3_remove(struct pci_dev *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-aspeed.c
@@ -172,6 +172,13 @@
 
 static int aspeed_i2c_reset(struct aspeed_i2c_bus *bus);
 
+/* precondition: bus.lock has been acquired. */
+static void aspeed_i2c_do_stop(struct aspeed_i2c_bus *bus)
+{
+	bus->master_state = ASPEED_I2C_MASTER_STOP;
+	writel(ASPEED_I2CD_M_STOP_CMD, bus->base + ASPEED_I2C_CMD_REG);
+}
+
 static int aspeed_i2c_recover_bus(struct aspeed_i2c_bus *bus)
 {
 	unsigned long time_left, flags;
@@ -189,7 +196,7 @@
 			command);
 
 		reinit_completion(&bus->cmd_complete);
-		writel(ASPEED_I2CD_M_STOP_CMD, bus->base + ASPEED_I2C_CMD_REG);
+		aspeed_i2c_do_stop(bus);
 		spin_unlock_irqrestore(&bus->lock, flags);
 
 		time_left = wait_for_completion_timeout(
@@ -250,18 +257,46 @@
 	if (!slave)
 		return 0;
 
-	command = readl(bus->base + ASPEED_I2C_CMD_REG);
+	/*
+	 * Handle stop conditions early, prior to SLAVE_MATCH. Some masters may drive
+	 * transfers with low enough latency between the nak/stop phase of the current
+	 * command and the start/address phase of the following command that the
+	 * interrupts are coalesced by the time we process them.
+	 */
+	if (irq_status & ASPEED_I2CD_INTR_NORMAL_STOP) {
+		irq_handled |= ASPEED_I2CD_INTR_NORMAL_STOP;
+		bus->slave_state = ASPEED_I2C_SLAVE_STOP;
+	}
+
+	if (irq_status & ASPEED_I2CD_INTR_TX_NAK &&
+	    bus->slave_state == ASPEED_I2C_SLAVE_READ_PROCESSED) {
+		irq_handled |= ASPEED_I2CD_INTR_TX_NAK;
+		bus->slave_state = ASPEED_I2C_SLAVE_STOP;
+	}
 
-	/* Slave was requested, restart state machine. */
+	/* Propagate any stop conditions to the slave implementation. */
+	if (bus->slave_state == ASPEED_I2C_SLAVE_STOP) {
+		i2c_slave_event(slave, I2C_SLAVE_STOP, &value);
+		bus->slave_state = ASPEED_I2C_SLAVE_INACTIVE;
+	}
+
+	/*
+	 * Now that we've dealt with any potentially coalesced stop conditions,
+	 * address any start conditions.
+	 */
 	if (irq_status & ASPEED_I2CD_INTR_SLAVE_MATCH) {
 		irq_handled |= ASPEED_I2CD_INTR_SLAVE_MATCH;
 		bus->slave_state = ASPEED_I2C_SLAVE_START;
 	}
 
-	/* Slave is not currently active, irq was for someone else. */
+	/*
+	 * If the slave has been stopped and not started then slave interrupt
+	 * handling is complete.
+	 */
 	if (bus->slave_state == ASPEED_I2C_SLAVE_INACTIVE)
 		return irq_handled;
 
+	command = readl(bus->base + ASPEED_I2C_CMD_REG);
 	dev_dbg(bus->dev, "slave irq status 0x%08x, cmd 0x%08x\n",
 		irq_status, command);
 
@@ -280,17 +315,6 @@
 		irq_handled |= ASPEED_I2CD_INTR_RX_DONE;
 	}
 
-	/* Slave was asked to stop. */
-	if (irq_status & ASPEED_I2CD_INTR_NORMAL_STOP) {
-		irq_handled |= ASPEED_I2CD_INTR_NORMAL_STOP;
-		bus->slave_state = ASPEED_I2C_SLAVE_STOP;
-	}
-	if (irq_status & ASPEED_I2CD_INTR_TX_NAK &&
-	    bus->slave_state == ASPEED_I2C_SLAVE_READ_PROCESSED) {
-		irq_handled |= ASPEED_I2CD_INTR_TX_NAK;
-		bus->slave_state = ASPEED_I2C_SLAVE_STOP;
-	}
-
 	switch (bus->slave_state) {
 	case ASPEED_I2C_SLAVE_READ_REQUESTED:
 		if (unlikely(irq_status & ASPEED_I2CD_INTR_TX_ACK))
@@ -319,8 +343,7 @@
 		i2c_slave_event(slave, I2C_SLAVE_WRITE_RECEIVED, &value);
 		break;
 	case ASPEED_I2C_SLAVE_STOP:
-		i2c_slave_event(slave, I2C_SLAVE_STOP, &value);
-		bus->slave_state = ASPEED_I2C_SLAVE_INACTIVE;
+		/* Stop event handling is done early. Unreachable. */
 		break;
 	case ASPEED_I2C_SLAVE_START:
 		/* Slave was just started. Waiting for the next event. */;
@@ -370,13 +393,6 @@
 }
 
 /* precondition: bus.lock has been acquired. */
-static void aspeed_i2c_do_stop(struct aspeed_i2c_bus *bus)
-{
-	bus->master_state = ASPEED_I2C_MASTER_STOP;
-	writel(ASPEED_I2CD_M_STOP_CMD, bus->base + ASPEED_I2C_CMD_REG);
-}
-
-/* precondition: bus.lock has been acquired. */
 static void aspeed_i2c_next_msg_or_stop(struct aspeed_i2c_bus *bus)
 {
 	if (bus->msgs_index + 1 < bus->msgs_count) {
@@ -693,13 +709,16 @@
 
 	if (time_left == 0) {
 		/*
-		 * If timed out and bus is still busy in a multi master
-		 * environment, attempt recovery at here.
+		 * In a multi-master setup, if a timeout occurs, attempt
+		 * recovery. But if the bus is idle, we still need to reset the
+		 * i2c controller to clear the remaining interrupts.
 		 */
 		if (bus->multi_master &&
 		    (readl(bus->base + ASPEED_I2C_CMD_REG) &
 		     ASPEED_I2CD_BUS_BUSY_STS))
 			aspeed_i2c_recover_bus(bus);
+		else
+			aspeed_i2c_reset(bus);
 
 		/*
 		 * If timed out and the state is still pending, drop the pending
@@ -741,6 +760,8 @@
 	func_ctrl_reg_val = readl(bus->base + ASPEED_I2C_FUN_CTRL_REG);
 	func_ctrl_reg_val |= ASPEED_I2CD_SLAVE_EN;
 	writel(func_ctrl_reg_val, bus->base + ASPEED_I2C_FUN_CTRL_REG);
+
+	bus->slave_state = ASPEED_I2C_SLAVE_INACTIVE;
 }
 
 static int aspeed_i2c_reg_slave(struct i2c_client *client)
@@ -757,7 +778,6 @@
 	__aspeed_i2c_reg_slave(bus, client->addr);
 
 	bus->slave = client;
-	bus->slave_state = ASPEED_I2C_SLAVE_INACTIVE;
 	spin_unlock_irqrestore(&bus->lock, flags);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-at91-master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-at91-master.c
@@ -656,6 +656,7 @@
 	unsigned int_addr_flag = 0;
 	struct i2c_msg *m_start = msg;
 	bool is_read;
+	u8 *dma_buf = NULL;
 
 	dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);
 
@@ -703,7 +704,17 @@
 	dev->msg = m_start;
 	dev->recv_len_abort = false;
 
+	if (dev->use_dma) {
+		dma_buf = i2c_get_dma_safe_msg_buf(m_start, 1);
+		if (!dma_buf) {
+			ret = -ENOMEM;
+			goto out;
+		}
+		dev->buf = dma_buf;
+	}
+
 	ret = at91_do_twi_transfer(dev);
+	i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
 
 	ret = (ret < 0) ? ret : num;
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-at91-slave.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-at91-slave.c
@@ -106,8 +106,7 @@
 
 static u32 at91_twi_func(struct i2c_adapter *adapter)
 {
-	return I2C_FUNC_SLAVE | I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL
-		| I2C_FUNC_SMBUS_READ_BLOCK_DATA;
+	return I2C_FUNC_SLAVE;
 }
 
 static const struct i2c_algorithm at91_twi_algorithm_slave = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-bcm-iproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -243,13 +243,14 @@
 				   u32 offset)
 {
 	u32 val;
+	unsigned long flags;
 
 	if (iproc_i2c->idm_base) {
-		spin_lock(&iproc_i2c->idm_lock);
+		spin_lock_irqsave(&iproc_i2c->idm_lock, flags);
 		writel(iproc_i2c->ape_addr_mask,
 		       iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
 		val = readl(iproc_i2c->base + offset);
-		spin_unlock(&iproc_i2c->idm_lock);
+		spin_unlock_irqrestore(&iproc_i2c->idm_lock, flags);
 	} else {
 		val = readl(iproc_i2c->base + offset);
 	}
@@ -260,12 +261,14 @@
 static inline void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
 				    u32 offset, u32 val)
 {
+	unsigned long flags;
+
 	if (iproc_i2c->idm_base) {
-		spin_lock(&iproc_i2c->idm_lock);
+		spin_lock_irqsave(&iproc_i2c->idm_lock, flags);
 		writel(iproc_i2c->ape_addr_mask,
 		       iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
 		writel(val, iproc_i2c->base + offset);
-		spin_unlock(&iproc_i2c->idm_lock);
+		spin_unlock_irqrestore(&iproc_i2c->idm_lock, flags);
 	} else {
 		writel(val, iproc_i2c->base + offset);
 	}
@@ -323,26 +326,44 @@
 	iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 }
 
-static void bcm_iproc_i2c_check_slave_status(
-	struct bcm_iproc_i2c_dev *iproc_i2c)
+static bool bcm_iproc_i2c_check_slave_status
+	(struct bcm_iproc_i2c_dev *iproc_i2c, u32 status)
 {
 	u32 val;
+	bool recover = false;
+
+	/* check slave transmit status only if slave is transmitting */
+	if (!iproc_i2c->slave_rx_only) {
+		val = iproc_i2c_rd_reg(iproc_i2c, S_CMD_OFFSET);
+		/* status is valid only when START_BUSY is cleared */
+		if (!(val & BIT(S_CMD_START_BUSY_SHIFT))) {
+			val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
+			if (val == S_CMD_STATUS_TIMEOUT ||
+			    val == S_CMD_STATUS_MASTER_ABORT) {
+				dev_warn(iproc_i2c->device,
+					 (val == S_CMD_STATUS_TIMEOUT) ?
+					 "slave random stretch time timeout\n" :
+					 "Master aborted read transaction\n");
+				recover = true;
+			}
+		}
+	}
 
-	val = iproc_i2c_rd_reg(iproc_i2c, S_CMD_OFFSET);
-	/* status is valid only when START_BUSY is cleared after it was set */
-	if (val & BIT(S_CMD_START_BUSY_SHIFT))
-		return;
-
-	val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
-	if (val == S_CMD_STATUS_TIMEOUT || val == S_CMD_STATUS_MASTER_ABORT) {
-		dev_err(iproc_i2c->device, (val == S_CMD_STATUS_TIMEOUT) ?
-			"slave random stretch time timeout\n" :
-			"Master aborted read transaction\n");
+	/* RX_EVENT is not valid when START_BUSY is set */
+	if ((status & BIT(IS_S_RX_EVENT_SHIFT)) &&
+	    (status & BIT(IS_S_START_BUSY_SHIFT))) {
+		dev_warn(iproc_i2c->device, "Slave aborted read transaction\n");
+		recover = true;
+	}
+
+	if (recover) {
 		/* re-initialize i2c for recovery */
 		bcm_iproc_i2c_enable_disable(iproc_i2c, false);
 		bcm_iproc_i2c_slave_init(iproc_i2c, true);
 		bcm_iproc_i2c_enable_disable(iproc_i2c, true);
 	}
+
+	return recover;
 }
 
 static void bcm_iproc_i2c_slave_read(struct bcm_iproc_i2c_dev *iproc_i2c)
@@ -427,48 +448,6 @@
 	u32 val;
 	u8 value;
 
-	/*
-	 * Slave events in case of master-write, master-write-read and,
-	 * master-read
-	 *
-	 * Master-write     : only IS_S_RX_EVENT_SHIFT event
-	 * Master-write-read: both IS_S_RX_EVENT_SHIFT and IS_S_RD_EVENT_SHIFT
-	 *                    events
-	 * Master-read      : both IS_S_RX_EVENT_SHIFT and IS_S_RD_EVENT_SHIFT
-	 *                    events or only IS_S_RD_EVENT_SHIFT
-	 *
-	 * iproc has a slave rx fifo size of 64 bytes. Rx fifo full interrupt
-	 * (IS_S_RX_FIFO_FULL_SHIFT) will be generated when RX fifo becomes
-	 * full. This can happen if Master issues write requests of more than
-	 * 64 bytes.
-	 */
-	if (status & BIT(IS_S_RX_EVENT_SHIFT) ||
-	    status & BIT(IS_S_RD_EVENT_SHIFT) ||
-	    status & BIT(IS_S_RX_FIFO_FULL_SHIFT)) {
-		/* disable slave interrupts */
-		val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
-		val &= ~iproc_i2c->slave_int_mask;
-		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
-
-		if (status & BIT(IS_S_RD_EVENT_SHIFT))
-			/* Master-write-read request */
-			iproc_i2c->slave_rx_only = false;
-		else
-			/* Master-write request only */
-			iproc_i2c->slave_rx_only = true;
-
-		/* schedule tasklet to read data later */
-		tasklet_schedule(&iproc_i2c->slave_rx_tasklet);
-
-		/*
-		 * clear only IS_S_RX_EVENT_SHIFT and
-		 * IS_S_RX_FIFO_FULL_SHIFT interrupt.
-		 */
-		val = BIT(IS_S_RX_EVENT_SHIFT);
-		if (status & BIT(IS_S_RX_FIFO_FULL_SHIFT))
-			val |= BIT(IS_S_RX_FIFO_FULL_SHIFT);
-		iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, val);
-	}
 
 	if (status & BIT(IS_S_TX_UNDERRUN_SHIFT)) {
 		iproc_i2c->tx_underrun++;
@@ -500,8 +479,9 @@
 		 * less than PKT_LENGTH bytes were output on the SMBUS
 		 */
 		iproc_i2c->slave_int_mask &= ~BIT(IE_S_TX_UNDERRUN_SHIFT);
-		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET,
-				 iproc_i2c->slave_int_mask);
+		val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
+		val &= ~BIT(IE_S_TX_UNDERRUN_SHIFT);
+		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 
 		/* End of SMBUS for Master Read */
 		val = BIT(S_TX_WR_STATUS_SHIFT);
@@ -522,9 +502,49 @@
 				 BIT(IS_S_START_BUSY_SHIFT));
 	}
 
-	/* check slave transmit status only if slave is transmitting */
-	if (!iproc_i2c->slave_rx_only)
-		bcm_iproc_i2c_check_slave_status(iproc_i2c);
+	/* if the controller has been reset, immediately return from the ISR */
+	if (bcm_iproc_i2c_check_slave_status(iproc_i2c, status))
+		return true;
+
+	/*
+	 * Slave events in case of master-write, master-write-read and,
+	 * master-read
+	 *
+	 * Master-write     : only IS_S_RX_EVENT_SHIFT event
+	 * Master-write-read: both IS_S_RX_EVENT_SHIFT and IS_S_RD_EVENT_SHIFT
+	 *                    events
+	 * Master-read      : both IS_S_RX_EVENT_SHIFT and IS_S_RD_EVENT_SHIFT
+	 *                    events or only IS_S_RD_EVENT_SHIFT
+	 *
+	 * iproc has a slave rx fifo size of 64 bytes. Rx fifo full interrupt
+	 * (IS_S_RX_FIFO_FULL_SHIFT) will be generated when RX fifo becomes
+	 * full. This can happen if Master issues write requests of more than
+	 * 64 bytes.
+	 */
+	if (status & BIT(IS_S_RX_EVENT_SHIFT) ||
+	    status & BIT(IS_S_RD_EVENT_SHIFT) ||
+	    status & BIT(IS_S_RX_FIFO_FULL_SHIFT)) {
+		/* disable slave interrupts */
+		val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
+		val &= ~iproc_i2c->slave_int_mask;
+		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
+
+		if (status & BIT(IS_S_RD_EVENT_SHIFT))
+			/* Master-write-read request */
+			iproc_i2c->slave_rx_only = false;
+		else
+			/* Master-write request only */
+			iproc_i2c->slave_rx_only = true;
+
+		/* schedule tasklet to read data later */
+		tasklet_schedule(&iproc_i2c->slave_rx_tasklet);
+
+		/* clear IS_S_RX_FIFO_FULL_SHIFT interrupt */
+		if (status & BIT(IS_S_RX_FIFO_FULL_SHIFT)) {
+			val = BIT(IS_S_RX_FIFO_FULL_SHIFT);
+			iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, val);
+		}
+	}
 
 	return true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-bcm2835.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-bcm2835.c
@@ -23,6 +23,11 @@
 #define BCM2835_I2C_FIFO	0x10
 #define BCM2835_I2C_DIV		0x14
 #define BCM2835_I2C_DEL		0x18
+/*
+ * 16-bit field for the number of SCL cycles to wait after rising SCL
+ * before deciding the slave is not responding. 0 disables the
+ * timeout detection.
+ */
 #define BCM2835_I2C_CLKT	0x1c
 
 #define BCM2835_I2C_C_READ	BIT(0)
@@ -402,7 +407,7 @@
 static int bcm2835_i2c_probe(struct platform_device *pdev)
 {
 	struct bcm2835_i2c_dev *i2c_dev;
-	struct resource *mem, *irq;
+	struct resource *mem;
 	int ret;
 	struct i2c_adapter *adap;
 	struct clk *mclk;
@@ -449,21 +454,20 @@
 	ret = clk_prepare_enable(i2c_dev->bus_clk);
 	if (ret) {
 		dev_err(&pdev->dev, "Couldn't prepare clock");
-		return ret;
+		goto err_put_exclusive_rate;
 	}
 
-	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (!irq) {
-		dev_err(&pdev->dev, "No IRQ resource\n");
-		return -ENODEV;
+	i2c_dev->irq = platform_get_irq(pdev, 0);
+	if (i2c_dev->irq < 0) {
+		ret = i2c_dev->irq;
+		goto err_disable_unprepare_clk;
 	}
-	i2c_dev->irq = irq->start;
 
 	ret = request_irq(i2c_dev->irq, bcm2835_i2c_isr, IRQF_SHARED,
 			  dev_name(&pdev->dev), i2c_dev);
 	if (ret) {
 		dev_err(&pdev->dev, "Could not request IRQ\n");
-		return -ENODEV;
+		goto err_disable_unprepare_clk;
 	}
 
 	adap = &i2c_dev->adapter;
@@ -477,11 +481,26 @@
 	adap->dev.of_node = pdev->dev.of_node;
 	adap->quirks = of_device_get_match_data(&pdev->dev);
 
+	/*
+	 * Disable the hardware clock stretching timeout. SMBUS
+	 * specifies a limit for how long the device can stretch the
+	 * clock, but core I2C doesn't.
+	 */
+	bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_CLKT, 0);
 	bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, 0);
 
 	ret = i2c_add_adapter(adap);
 	if (ret)
-		free_irq(i2c_dev->irq, i2c_dev);
+		goto err_free_irq;
+
+	return 0;
+
+err_free_irq:
+	free_irq(i2c_dev->irq, i2c_dev);
+err_disable_unprepare_clk:
+	clk_disable_unprepare(i2c_dev->bus_clk);
+err_put_exclusive_rate:
+	clk_rate_exclusive_put(i2c_dev->bus_clk);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-brcmstb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-brcmstb.c
@@ -673,7 +673,7 @@
 
 	/* set the data in/out register size for compatible SoCs */
 	if (of_device_is_compatible(dev->device->of_node,
-				    "brcmstb,brcmper-i2c"))
+				    "brcm,brcmper-i2c"))
 		dev->data_regsz = sizeof(u8);
 	else
 		dev->data_regsz = sizeof(u32);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-cadence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-cadence.c
@@ -7,13 +7,16 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
+#include <linux/of_gpio.h>
 #include <linux/pm_runtime.h>
+#include <linux/pinctrl/consumer.h>
 
 /* Register offsets for the I2C device. */
 #define CDNS_I2C_CR_OFFSET		0x00 /* Control Register, RW */
@@ -22,12 +25,14 @@
 #define CDNS_I2C_DATA_OFFSET		0x0C /* I2C Data Register, RW */
 #define CDNS_I2C_ISR_OFFSET		0x10 /* IRQ Status Register, RW */
 #define CDNS_I2C_XFER_SIZE_OFFSET	0x14 /* Transfer Size Register, RW */
+#define CDNS_I2C_SLV_PAUSE_OFFSET	0x18 /* Transfer Size Register, RW */
 #define CDNS_I2C_TIME_OUT_OFFSET	0x1C /* Time Out Register, RW */
 #define CDNS_I2C_IMR_OFFSET		0x20 /* IRQ Mask Register, RO */
 #define CDNS_I2C_IER_OFFSET		0x24 /* IRQ Enable Register, WO */
 #define CDNS_I2C_IDR_OFFSET		0x28 /* IRQ Disable Register, WO */
 
 /* Control Register Bit mask definitions */
+#define CDNS_I2C_CR_SLVMON		BIT(5) /* Slave monitor mode bit */
 #define CDNS_I2C_CR_HOLD		BIT(4) /* Hold Bus bit */
 #define CDNS_I2C_CR_ACK_EN		BIT(3)
 #define CDNS_I2C_CR_NEA			BIT(2)
@@ -179,6 +184,10 @@
  * @clk_rate_change_nb:	Notifier block for clock rate changes
  * @quirks:		flag for broken hold bit usage in r1p10
  * @ctrl_reg:		Cached value of the control register.
+ * @rinfo:		Structure holding recovery information.
+ * @pinctrl:		Pin control state holder.
+ * @pinctrl_pins_default: Default pin control state.
+ * @pinctrl_pins_gpio:	GPIO pin control state.
  * @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register
  * @slave:		Registered slave instance.
  * @dev_mode:		I2C operating role(master/slave).
@@ -204,6 +213,10 @@
 	struct notifier_block clk_rate_change_nb;
 	u32 quirks;
 	u32 ctrl_reg;
+	struct i2c_bus_recovery_info rinfo;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pinctrl_pins_default;
+	struct pinctrl_state *pinctrl_pins_gpio;
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	u16 ctrl_reg_diva_divb;
 	struct i2c_client *slave;
@@ -388,9 +401,9 @@
  */
 static irqreturn_t cdns_i2c_master_isr(void *ptr)
 {
-	unsigned int isr_status, avail_bytes, updatetx;
+	unsigned int isr_status, avail_bytes;
 	unsigned int bytes_to_send;
-	bool hold_quirk;
+	bool updatetx;
 	struct cdns_i2c *id = ptr;
 	/* Signal completion only after everything is updated */
 	int done_flag = 0;
@@ -410,11 +423,7 @@
 	 * Check if transfer size register needs to be updated again for a
 	 * large data receive operation.
 	 */
-	updatetx = 0;
-	if (id->recv_count > id->curr_recv_count)
-		updatetx = 1;
-
-	hold_quirk = (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT) && updatetx;
+	updatetx = id->recv_count > id->curr_recv_count;
 
 	/* When receiving, handle data interrupt and completion interrupt */
 	if (id->p_recv_buf &&
@@ -445,7 +454,7 @@
 				break;
 			}
 
-			if (cdns_is_holdquirk(id, hold_quirk))
+			if (cdns_is_holdquirk(id, updatetx))
 				break;
 		}
 
@@ -456,7 +465,7 @@
 		 * maintain transfer size non-zero while performing a large
 		 * receive operation.
 		 */
-		if (cdns_is_holdquirk(id, hold_quirk)) {
+		if (cdns_is_holdquirk(id, updatetx)) {
 			/* wait while fifo is full */
 			while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) !=
 			       (id->curr_recv_count - CDNS_I2C_FIFO_DEPTH))
@@ -478,22 +487,6 @@
 						  CDNS_I2C_XFER_SIZE_OFFSET);
 				id->curr_recv_count = id->recv_count;
 			}
-		} else if (id->recv_count && !hold_quirk &&
-						!id->curr_recv_count) {
-
-			/* Set the slave address in address register*/
-			cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
-						CDNS_I2C_ADDR_OFFSET);
-
-			if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
-				cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
-						CDNS_I2C_XFER_SIZE_OFFSET);
-				id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
-			} else {
-				cdns_i2c_writereg(id->recv_count,
-						CDNS_I2C_XFER_SIZE_OFFSET);
-				id->curr_recv_count = id->recv_count;
-			}
 		}
 
 		/* Clear hold (if not repeated start) and signal completion */
@@ -540,6 +533,23 @@
 		status = IRQ_HANDLED;
 	}
 
+	/* Handling Slave monitor mode interrupt */
+	if (isr_status & CDNS_I2C_IXR_SLV_RDY) {
+		unsigned int ctrl_reg;
+		/* Read control register */
+		ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
+
+		/* Disable slave monitor mode */
+		ctrl_reg &= ~CDNS_I2C_CR_SLVMON;
+		cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
+
+		/* Clear interrupt flag for slvmon mode */
+		cdns_i2c_writereg(CDNS_I2C_IXR_SLV_RDY, CDNS_I2C_IDR_OFFSET);
+
+		done_flag = 1;
+		status = IRQ_HANDLED;
+	}
+
 	/* Update the status for errors */
 	id->err_status |= isr_status & CDNS_I2C_IXR_ERR_INTR_MASK;
 	if (id->err_status)
@@ -593,8 +603,13 @@
 	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
 	ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO;
 
+	/*
+	 * Receive up to I2C_SMBUS_BLOCK_MAX data bytes, plus one message length
+	 * byte, plus one checksum byte if PEC is enabled. p_msg->len will be 2 if
+	 * PEC is enabled, otherwise 1.
+	 */
 	if (id->p_msg->flags & I2C_M_RECV_LEN)
-		id->recv_count = I2C_SMBUS_BLOCK_MAX + 1;
+		id->recv_count = I2C_SMBUS_BLOCK_MAX + id->p_msg->len;
 
 	id->curr_recv_count = id->recv_count;
 
@@ -729,6 +744,40 @@
 }
 
 /**
+ * cdns_i2c_slvmon - Handling Slav monitor mode feature
+ * @id:		pointer to the i2c device
+ */
+static void cdns_i2c_slvmon(struct cdns_i2c *id)
+{
+	unsigned int ctrl_reg;
+	unsigned int isr_status;
+
+	id->p_recv_buf = NULL;
+	id->p_send_buf = id->p_msg->buf;
+	id->send_count = id->p_msg->len;
+
+	/* Clear the interrupts in interrupt status register. */
+	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
+	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
+
+	/* Enable slvmon control reg */
+	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
+	ctrl_reg |=  CDNS_I2C_CR_MS | CDNS_I2C_CR_NEA | CDNS_I2C_CR_SLVMON
+			| CDNS_I2C_CR_CLR_FIFO;
+	ctrl_reg &= ~(CDNS_I2C_CR_RW);
+	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
+
+	/* Initialize slvmon reg */
+	cdns_i2c_writereg(0xF, CDNS_I2C_SLV_PAUSE_OFFSET);
+
+	/* Set the slave address to start the slave address transmission */
+	cdns_i2c_writereg(id->p_msg->addr, CDNS_I2C_ADDR_OFFSET);
+
+	/* Setup slvmon interrupt flag */
+	cdns_i2c_writereg(CDNS_I2C_IXR_SLV_RDY, CDNS_I2C_IER_OFFSET);
+}
+
+/**
  * cdns_i2c_master_reset - Reset the interface
  * @adap:	pointer to the i2c adapter driver instance
  *
@@ -744,7 +793,7 @@
 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
 	/* Clear the hold bit and fifos */
 	regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
-	regval &= ~CDNS_I2C_CR_HOLD;
+	regval &= ~(CDNS_I2C_CR_HOLD | CDNS_I2C_CR_SLVMON);
 	regval |= CDNS_I2C_CR_CLR_FIFO;
 	cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET);
 	/* Update the transfercount register to zero */
@@ -760,7 +809,7 @@
 static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg,
 		struct i2c_adapter *adap)
 {
-	unsigned long time_left;
+	unsigned long time_left, msg_timeout;
 	u32 reg;
 
 	id->p_msg = msg;
@@ -778,16 +827,27 @@
 			cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA,
 					CDNS_I2C_CR_OFFSET);
 	}
-
-	/* Check for the R/W flag on each msg */
-	if (msg->flags & I2C_M_RD)
+	/* Check for zero length - Slave monitor mode */
+	if (msg->len == 0)
+		cdns_i2c_slvmon(id);
+	 /* Check for the R/W flag on each msg */
+	else if (msg->flags & I2C_M_RD)
 		cdns_i2c_mrecv(id);
 	else
 		cdns_i2c_msend(id);
 
+	/* Minimal time to execute this message */
+	msg_timeout = msecs_to_jiffies((1000 * msg->len * BITS_PER_BYTE) / id->i2c_clk);
+	/* Plus some wiggle room */
+	msg_timeout += msecs_to_jiffies(500);
+
+	if (msg_timeout < adap->timeout)
+		msg_timeout = adap->timeout;
+
 	/* Wait for the signal of completion */
-	time_left = wait_for_completion_timeout(&id->xfer_done, adap->timeout);
+	time_left = wait_for_completion_timeout(&id->xfer_done, msg_timeout);
 	if (time_left == 0) {
+		i2c_recover_bus(adap);
 		cdns_i2c_master_reset(adap);
 		dev_err(id->adap.dev.parent,
 				"timeout waiting on completion\n");
@@ -801,6 +861,9 @@
 	if (id->err_status & CDNS_I2C_IXR_ARB_LOST)
 		return -EAGAIN;
 
+	if (msg->flags & I2C_M_RECV_LEN)
+		msg->len += min_t(unsigned int, msg->buf[0], I2C_SMBUS_BLOCK_MAX);
+
 	return 0;
 }
 
@@ -832,8 +895,10 @@
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	/* Check i2c operating mode and switch if possible */
 	if (id->dev_mode == CDNS_I2C_MODE_SLAVE) {
-		if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE)
-			return -EAGAIN;
+		if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE) {
+			ret = -EAGAIN;
+			goto out;
+		}
 
 		/* Set mode to master */
 		cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
@@ -844,10 +909,11 @@
 #endif
 
 	/* Check if the bus is free */
-	if (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & CDNS_I2C_SR_BA) {
-		ret = -EAGAIN;
-		goto out;
-	}
+	if (msgs->len)
+		if (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & CDNS_I2C_SR_BA) {
+			ret = -EAGAIN;
+			goto out;
+		}
 
 	hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT);
 	/*
@@ -1208,6 +1274,96 @@
 	return 0;
 }
 
+/**
+ * cdns_i2c_prepare_recovery - Withhold recovery state
+ * @adapter:    Pointer to i2c adapter
+ *
+ * This function is called to prepare for recovery.
+ * It changes the state of pins from SCL/SDA to GPIO.
+ */
+static void cdns_i2c_prepare_recovery(struct i2c_adapter *adapter)
+{
+	struct cdns_i2c *p_cdns_i2c;
+	int ret;
+
+	p_cdns_i2c = container_of(adapter, struct cdns_i2c, adap);
+
+	/* Setting pin state as gpio */
+	ret = pinctrl_select_state(p_cdns_i2c->pinctrl,
+			     p_cdns_i2c->pinctrl_pins_gpio);
+	if (ret < 0)
+		dev_err(p_cdns_i2c->adap.dev.parent,
+				"pinctrl_select_state failed\n");
+}
+
+/**
+ * cdns_i2c_unprepare_recovery - Release recovery state
+ * @adapter:    Pointer to i2c adapter
+ *
+ * This function is called on exiting recovery. It reverts
+ * the state of pins from GPIO to SCL/SDA.
+ */
+static void cdns_i2c_unprepare_recovery(struct i2c_adapter *adapter)
+{
+	struct cdns_i2c *p_cdns_i2c;
+	int ret;
+
+	p_cdns_i2c = container_of(adapter, struct cdns_i2c, adap);
+
+	/* Setting pin state to default(i2c) */
+	ret = pinctrl_select_state(p_cdns_i2c->pinctrl,
+			     p_cdns_i2c->pinctrl_pins_default);
+	if (ret < 0)
+		dev_err(p_cdns_i2c->adap.dev.parent,
+				"pinctrl_select_state failed\n");
+}
+
+/**
+ * cdns_i2c_init_recovery_info  - Initialize I2C bus recovery
+ * @pid:        Pointer to cdns i2c structure
+ * @pdev:       Handle to the platform device structure
+ *
+ * This function does required initialization for i2c bus
+ * recovery. It registers three functions for prepare,
+ * recover and unprepare
+ *
+ * Return: 0 on Success, negative error otherwise.
+ */
+static int cdns_i2c_init_recovery_info(struct cdns_i2c *pid,
+		struct platform_device *pdev)
+{
+	struct i2c_bus_recovery_info *rinfo = &pid->rinfo;
+
+	pid->pinctrl_pins_default = pinctrl_lookup_state(pid->pinctrl,
+			PINCTRL_STATE_DEFAULT);
+	pid->pinctrl_pins_gpio = pinctrl_lookup_state(pid->pinctrl, "gpio");
+
+	/* Fetches GPIO pins */
+	rinfo->sda_gpiod = devm_gpiod_get(&pdev->dev, "sda-gpios", GPIOD_ASIS);
+	rinfo->scl_gpiod = devm_gpiod_get(&pdev->dev, "scl-gpios", GPIOD_ASIS);
+
+	/* if GPIO driver isn't ready yet, deffer probe */
+	if (PTR_ERR(rinfo->sda_gpiod) == -EPROBE_DEFER ||
+	    PTR_ERR(rinfo->scl_gpiod) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	/* Validates fetched information */
+	if (IS_ERR(rinfo->sda_gpiod) ||
+	    IS_ERR(rinfo->scl_gpiod) ||
+			IS_ERR(pid->pinctrl_pins_default) ||
+			IS_ERR(pid->pinctrl_pins_gpio)) {
+		dev_dbg(&pdev->dev, "recovery information incomplete\n");
+		return 0;
+	}
+
+	rinfo->prepare_recovery     = cdns_i2c_prepare_recovery;
+	rinfo->unprepare_recovery   = cdns_i2c_unprepare_recovery;
+	rinfo->recover_bus          = i2c_generic_scl_recovery;
+	pid->adap.bus_recovery_info = rinfo;
+
+	return 0;
+}
+
 static const struct dev_pm_ops cdns_i2c_dev_pm_ops = {
 	SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend,
 			   cdns_i2c_runtime_resume, NULL)
@@ -1254,6 +1410,13 @@
 		id->quirks = data->quirks;
 	}
 
+	id->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (!IS_ERR(id->pinctrl)) {
+		ret = cdns_i2c_init_recovery_info(id, pdev);
+		if (ret)
+			return ret;
+	}
+
 	id->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &r_mem);
 	if (IS_ERR(id->membase))
 		return PTR_ERR(id->membase);
@@ -1330,6 +1493,7 @@
 	return 0;
 
 err_clk_dis:
+	clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
 	clk_disable_unprepare(id->clk);
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_set_suspended(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-cbus-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-cbus-gpio.c
@@ -195,8 +195,9 @@
 }
 
 static const struct i2c_algorithm cbus_i2c_algo = {
-	.smbus_xfer	= cbus_i2c_smbus_xfer,
-	.functionality	= cbus_i2c_func,
+	.smbus_xfer		= cbus_i2c_smbus_xfer,
+	.smbus_xfer_atomic	= cbus_i2c_smbus_xfer,
+	.functionality		= cbus_i2c_func,
 };
 
 static int cbus_i2c_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-designware-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-designware-common.c
@@ -63,7 +63,7 @@
 {
 	struct dw_i2c_dev *dev = context;
 
-	*val = readl_relaxed(dev->base + reg);
+	*val = readl(dev->base + reg);
 
 	return 0;
 }
@@ -72,7 +72,7 @@
 {
 	struct dw_i2c_dev *dev = context;
 
-	writel_relaxed(val, dev->base + reg);
+	writel(val, dev->base + reg);
 
 	return 0;
 }
@@ -81,7 +81,7 @@
 {
 	struct dw_i2c_dev *dev = context;
 
-	*val = swab32(readl_relaxed(dev->base + reg));
+	*val = swab32(readl(dev->base + reg));
 
 	return 0;
 }
@@ -90,7 +90,7 @@
 {
 	struct dw_i2c_dev *dev = context;
 
-	writel_relaxed(swab32(val), dev->base + reg);
+	writel(swab32(val), dev->base + reg);
 
 	return 0;
 }
@@ -99,8 +99,8 @@
 {
 	struct dw_i2c_dev *dev = context;
 
-	*val = readw_relaxed(dev->base + reg) |
-		(readw_relaxed(dev->base + reg + 2) << 16);
+	*val = readw(dev->base + reg) |
+		(readw(dev->base + reg + 2) << 16);
 
 	return 0;
 }
@@ -109,8 +109,8 @@
 {
 	struct dw_i2c_dev *dev = context;
 
-	writew_relaxed(val, dev->base + reg);
-	writew_relaxed(val >> 16, dev->base + reg + 2);
+	writew(val, dev->base + reg);
+	writew(val >> 16, dev->base + reg + 2);
 
 	return 0;
 }
@@ -351,7 +351,8 @@
 		 *
 		 * If your hardware is free from tHD;STA issue, try this one.
 		 */
-		return DIV_ROUND_CLOSEST(ic_clk * tSYMBOL, MICRO) - 8 + offset;
+		return DIV_ROUND_CLOSEST_ULL((u64)ic_clk * tSYMBOL, MICRO) -
+		       8 + offset;
 	else
 		/*
 		 * Conditional expression:
@@ -367,7 +368,8 @@
 		 * The reason why we need to take into account "tf" here,
 		 * is the same as described in i2c_dw_scl_lcnt().
 		 */
-		return DIV_ROUND_CLOSEST(ic_clk * (tSYMBOL + tf), MICRO) - 3 + offset;
+		return DIV_ROUND_CLOSEST_ULL((u64)ic_clk * (tSYMBOL + tf), MICRO) -
+		       3 + offset;
 }
 
 u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset)
@@ -383,7 +385,8 @@
 	 * account the fall time of SCL signal (tf).  Default tf value
 	 * should be 0.3 us, for safety.
 	 */
-	return DIV_ROUND_CLOSEST(ic_clk * (tLOW + tf), MICRO) - 1 + offset;
+	return DIV_ROUND_CLOSEST_ULL((u64)ic_clk * (tLOW + tf), MICRO) -
+	       1 + offset;
 }
 
 int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev)
@@ -462,7 +465,7 @@
 	dev_warn(dev->dev, "timeout in disabling adapter\n");
 }
 
-unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev)
+u32 i2c_dw_clk_rate(struct dw_i2c_dev *dev)
 {
 	/*
 	 * Clock is not necessary if we got LCNT/HCNT values directly from
@@ -477,9 +480,6 @@
 {
 	int ret;
 
-	if (IS_ERR(dev->clk))
-		return PTR_ERR(dev->clk);
-
 	if (prepare) {
 		/* Optional interface clock */
 		ret = clk_prepare_enable(dev->pclk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-designware-core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-designware-core.h
@@ -126,8 +126,9 @@
  * status codes
  */
 #define STATUS_IDLE			0x0
-#define STATUS_WRITE_IN_PROGRESS	0x1
-#define STATUS_READ_IN_PROGRESS		0x2
+#define STATUS_ACTIVE			0x1
+#define STATUS_WRITE_IN_PROGRESS	0x2
+#define STATUS_READ_IN_PROGRESS		0x4
 
 /*
  * operation modes
@@ -309,7 +310,7 @@
 u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset);
 u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset);
 int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev);
-unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev);
+u32 i2c_dw_clk_rate(struct dw_i2c_dev *dev);
 int i2c_dw_prepare_clk(struct dw_i2c_dev *dev, bool prepare);
 int i2c_dw_acquire_lock(struct dw_i2c_dev *dev);
 void i2c_dw_release_lock(struct dw_i2c_dev *dev);
@@ -322,12 +323,14 @@
 
 static inline void __i2c_dw_enable(struct dw_i2c_dev *dev)
 {
+	dev->status |= STATUS_ACTIVE;
 	regmap_write(dev->map, DW_IC_ENABLE, 1);
 }
 
 static inline void __i2c_dw_disable_nowait(struct dw_i2c_dev *dev)
 {
 	regmap_write(dev->map, DW_IC_ENABLE, 0);
+	dev->status &= ~STATUS_ACTIVE;
 }
 
 void __i2c_dw_disable(struct dw_i2c_dev *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-designware-master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-designware-master.c
@@ -456,10 +456,16 @@
 
 		/*
 		 * Because we don't know the buffer length in the
-		 * I2C_FUNC_SMBUS_BLOCK_DATA case, we can't stop
-		 * the transaction here.
+		 * I2C_FUNC_SMBUS_BLOCK_DATA case, we can't stop the
+		 * transaction here. Also disable the TX_EMPTY IRQ
+		 * while waiting for the data length byte to avoid the
+		 * bogus interrupts flood.
 		 */
-		if (buf_len > 0 || flags & I2C_M_RECV_LEN) {
+		if (flags & I2C_M_RECV_LEN) {
+			dev->status |= STATUS_WRITE_IN_PROGRESS;
+			intr_mask &= ~DW_IC_INTR_TX_EMPTY;
+			break;
+		} else if (buf_len > 0) {
 			/* more bytes to be written */
 			dev->status |= STATUS_WRITE_IN_PROGRESS;
 			break;
@@ -495,6 +501,13 @@
 	msgs[dev->msg_read_idx].len = len;
 	msgs[dev->msg_read_idx].flags &= ~I2C_M_RECV_LEN;
 
+	/*
+	 * Received buffer length, re-enable TX_EMPTY interrupt
+	 * to resume the SMBUS transaction.
+	 */
+	regmap_update_bits(dev->map, DW_IC_INTR_MASK, DW_IC_INTR_TX_EMPTY,
+			   DW_IC_INTR_TX_EMPTY);
+
 	return len;
 }
 
@@ -525,9 +538,21 @@
 			u32 flags = msgs[dev->msg_read_idx].flags;
 
 			regmap_read(dev->map, DW_IC_DATA_CMD, &tmp);
+			tmp &= DW_IC_DATA_CMD_DAT;
 			/* Ensure length byte is a valid value */
-			if (flags & I2C_M_RECV_LEN &&
-			    (tmp & DW_IC_DATA_CMD_DAT) <= I2C_SMBUS_BLOCK_MAX && tmp > 0) {
+			if (flags & I2C_M_RECV_LEN) {
+				/*
+				 * if IC_EMPTYFIFO_HOLD_MASTER_EN is set, which cannot be
+				 * detected from the registers, the controller can be
+				 * disabled if the STOP bit is set. But it is only set
+				 * after receiving block data response length in
+				 * I2C_FUNC_SMBUS_BLOCK_DATA case. That needs to read
+				 * another byte with STOP bit set when the block data
+				 * response length is invalid to complete the transaction.
+				 */
+				if (!tmp || tmp > I2C_SMBUS_BLOCK_MAX)
+					tmp = 1;
+
 				len = i2c_dw_recv_len(dev, tmp);
 			}
 			*buf++ = tmp;
@@ -720,6 +745,19 @@
 	u32 stat;
 
 	stat = i2c_dw_read_clear_intrbits(dev);
+
+	if (!(dev->status & STATUS_ACTIVE)) {
+		/*
+		 * Unexpected interrupt in driver point of view. State
+		 * variables are either unset or stale so acknowledge and
+		 * disable interrupts for suppressing further interrupts if
+		 * interrupt really came from this HW (E.g. firmware has left
+		 * the HW active).
+		 */
+		regmap_write(dev->map, DW_IC_INTR_MASK, 0);
+		return 0;
+	}
+
 	if (stat & DW_IC_INTR_TX_ABRT) {
 		dev->cmd_err |= DW_IC_ERR_TX_ABRT;
 		dev->status = STATUS_IDLE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-designware-pcidrv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-designware-pcidrv.c
@@ -39,10 +39,10 @@
 };
 
 struct dw_scl_sda_cfg {
-	u32 ss_hcnt;
-	u32 fs_hcnt;
-	u32 ss_lcnt;
-	u32 fs_lcnt;
+	u16 ss_hcnt;
+	u16 fs_hcnt;
+	u16 ss_lcnt;
+	u16 fs_lcnt;
 	u32 sda_hold;
 };
 
@@ -398,6 +398,8 @@
 	{ PCI_VDEVICE(ATI,  0x73a4), navi_amd },
 	{ PCI_VDEVICE(ATI,  0x73e4), navi_amd },
 	{ PCI_VDEVICE(ATI,  0x73c4), navi_amd },
+	{ PCI_VDEVICE(ATI,  0x7444), navi_amd },
+	{ PCI_VDEVICE(ATI,  0x7464), navi_amd },
 	{ 0,}
 };
 MODULE_DEVICE_TABLE(pci, i2_designware_pci_ids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-designware-platdrv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -262,8 +262,17 @@
 		goto exit_reset;
 	}
 
-	dev->clk = devm_clk_get(&pdev->dev, NULL);
-	if (!i2c_dw_prepare_clk(dev, true)) {
+	dev->clk = devm_clk_get_optional(&pdev->dev, NULL);
+	if (IS_ERR(dev->clk)) {
+		ret = PTR_ERR(dev->clk);
+		goto exit_reset;
+	}
+
+	ret = i2c_dw_prepare_clk(dev, true);
+	if (ret)
+		goto exit_reset;
+
+	if (dev->clk) {
 		u64 clk_khz;
 
 		dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-designware-slave.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-designware-slave.c
@@ -232,7 +232,7 @@
 
 void i2c_dw_configure_slave(struct dw_i2c_dev *dev)
 {
-	dev->functionality = I2C_FUNC_SLAVE | DW_IC_DEFAULT_FUNCTIONALITY;
+	dev->functionality = I2C_FUNC_SLAVE;
 
 	dev->slave_cfg = DW_IC_CON_RX_FIFO_FULL_HLD_CTRL |
 			 DW_IC_CON_RESTART_EN | DW_IC_CON_STOP_DET_IFADDRESSED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-hisi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-hisi.c
@@ -315,6 +315,13 @@
 		    max_write == 0)
 			break;
 	}
+
+	/*
+	 * Disable the TX_EMPTY interrupt after finishing all the messages to
+	 * avoid overwhelming the CPU.
+	 */
+	if (ctlr->msg_tx_idx == ctlr->msg_num)
+		hisi_i2c_disable_int(ctlr, HISI_I2C_INT_TX_EMPTY);
 }
 
 static irqreturn_t hisi_i2c_irq(int irq, void *context)
@@ -322,6 +329,14 @@
 	struct hisi_i2c_controller *ctlr = context;
 	u32 int_stat;
 
+	/*
+	 * Don't handle the interrupt if cltr->completion is NULL. We may
+	 * reach here because the interrupt is spurious or the transfer is
+	 * started by another port (e.g. firmware) rather than us.
+	 */
+	if (!ctlr->completion)
+		return IRQ_NONE;
+
 	int_stat = readl(ctlr->iobase + HISI_I2C_INT_MSTAT);
 	hisi_i2c_clear_int(ctlr, int_stat);
 	if (!(int_stat & HISI_I2C_INT_ALL))
@@ -340,7 +355,11 @@
 		hisi_i2c_read_rx_fifo(ctlr);
 
 out:
-	if (int_stat & HISI_I2C_INT_TRANS_CPLT || ctlr->xfer_err) {
+	/*
+	 * Only use TRANS_CPLT to indicate the completion. On error cases we'll
+	 * get two interrupts, INT_ERR first then TRANS_CPLT.
+	 */
+	if (int_stat & HISI_I2C_INT_TRANS_CPLT) {
 		hisi_i2c_disable_int(ctlr, HISI_I2C_INT_ALL);
 		hisi_i2c_clear_int(ctlr, HISI_I2C_INT_ALL);
 		complete(ctlr->completion);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-i801.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-i801.c
@@ -519,12 +519,13 @@
 		return -EOPNOTSUPP;
 	}
 
-	inb_p(SMBHSTCNT(priv)); /* reset the data buffer index */
+	/* Set block buffer mode */
+	outb_p(inb_p(SMBAUXCTL(priv)) | SMBAUXCTL_E32B, SMBAUXCTL(priv));
 
-	/* Use 32-byte buffer to process this transaction */
 	if (read_write == I2C_SMBUS_WRITE) {
 		len = data->block[0];
 		outb_p(len, SMBHSTDAT0(priv));
+		inb_p(SMBHSTCNT(priv));	/* reset the data buffer index */
 		for (i = 0; i < len; i++)
 			outb_p(data->block[i+1], SMBBLKDAT(priv));
 	}
@@ -540,6 +541,7 @@
 			return -EPROTO;
 
 		data->block[0] = len;
+		inb_p(SMBHSTCNT(priv));	/* reset the data buffer index */
 		for (i = 0; i < len; i++)
 			data->block[i + 1] = inb_p(SMBBLKDAT(priv));
 	}
@@ -702,15 +704,11 @@
 		return i801_check_post(priv, result ? priv->status : -ETIMEDOUT);
 	}
 
-	for (i = 1; i <= len; i++) {
-		if (i == len && read_write == I2C_SMBUS_READ)
-			smbcmd |= SMBHSTCNT_LAST_BYTE;
-		outb_p(smbcmd, SMBHSTCNT(priv));
-
-		if (i == 1)
-			outb_p(inb(SMBHSTCNT(priv)) | SMBHSTCNT_START,
-			       SMBHSTCNT(priv));
+	if (len == 1 && read_write == I2C_SMBUS_READ)
+		smbcmd |= SMBHSTCNT_LAST_BYTE;
+	outb_p(smbcmd | SMBHSTCNT_START, SMBHSTCNT(priv));
 
+	for (i = 1; i <= len; i++) {
 		status = i801_wait_byte_done(priv);
 		if (status)
 			goto exit;
@@ -733,9 +731,12 @@
 			data->block[0] = len;
 		}
 
-		/* Retrieve/store value in SMBBLKDAT */
-		if (read_write == I2C_SMBUS_READ)
+		if (read_write == I2C_SMBUS_READ) {
 			data->block[i] = inb_p(SMBBLKDAT(priv));
+			if (i == len - 1)
+				outb_p(smbcmd | SMBHSTCNT_LAST_BYTE, SMBHSTCNT(priv));
+		}
+
 		if (read_write == I2C_SMBUS_WRITE && i+1 <= len)
 			outb_p(data->block[i+1], SMBBLKDAT(priv));
 
@@ -748,14 +749,6 @@
 	return i801_check_post(priv, status);
 }
 
-static int i801_set_block_buffer_mode(struct i801_priv *priv)
-{
-	outb_p(inb_p(SMBAUXCTL(priv)) | SMBAUXCTL_E32B, SMBAUXCTL(priv));
-	if ((inb_p(SMBAUXCTL(priv)) & SMBAUXCTL_E32B) == 0)
-		return -EIO;
-	return 0;
-}
-
 /* Block transaction function */
 static int i801_block_transaction(struct i801_priv *priv, union i2c_smbus_data *data,
 				  char read_write, int command)
@@ -763,6 +756,11 @@
 	int result = 0;
 	unsigned char hostc;
 
+	if (read_write == I2C_SMBUS_READ && command == I2C_SMBUS_BLOCK_DATA)
+		data->block[0] = I2C_SMBUS_BLOCK_MAX;
+	else if (data->block[0] < 1 || data->block[0] > I2C_SMBUS_BLOCK_MAX)
+		return -EPROTO;
+
 	if (command == I2C_SMBUS_I2C_BLOCK_DATA) {
 		if (read_write == I2C_SMBUS_WRITE) {
 			/* set I2C_EN bit in configuration register */
@@ -776,22 +774,11 @@
 		}
 	}
 
-	if (read_write == I2C_SMBUS_WRITE
-	 || command == I2C_SMBUS_I2C_BLOCK_DATA) {
-		if (data->block[0] < 1)
-			data->block[0] = 1;
-		if (data->block[0] > I2C_SMBUS_BLOCK_MAX)
-			data->block[0] = I2C_SMBUS_BLOCK_MAX;
-	} else {
-		data->block[0] = 32;	/* max for SMBus block reads */
-	}
-
 	/* Experience has shown that the block buffer can only be used for
 	   SMBus (not I2C) block transactions, even though the datasheet
 	   doesn't mention this limitation. */
-	if ((priv->features & FEATURE_BLOCK_BUFFER)
-	 && command != I2C_SMBUS_I2C_BLOCK_DATA
-	 && i801_set_block_buffer_mode(priv) == 0)
+	if ((priv->features & FEATURE_BLOCK_BUFFER) &&
+	    command != I2C_SMBUS_I2C_BLOCK_DATA)
 		result = i801_block_transaction_by_block(priv, data,
 							 read_write,
 							 command);
@@ -1058,7 +1045,7 @@
 MODULE_DEVICE_TABLE(pci, i801_ids);
 
 #if defined CONFIG_X86 && defined CONFIG_DMI
-static unsigned char apanel_addr;
+static unsigned char apanel_addr __ro_after_init;
 
 /* Scan the system ROM for the signature "FJKEYINF" */
 static __init const void __iomem *bios_signature(const void __iomem *bios)
@@ -1247,6 +1234,7 @@
 	 */
 	{ "Latitude 5480",      0x29 },
 	{ "Vostro V131",        0x1d },
+	{ "Vostro 5568",        0x29 },
 };
 
 static void register_dell_lis3lv02d_i2c_device(struct i801_priv *priv)
@@ -1428,7 +1416,6 @@
 				    mux_config->gpios[i], "mux", 0);
 	}
 	gpiod_add_lookup_table(lookup);
-	priv->lookup = lookup;
 
 	/*
 	 * Register the mux device, we use PLATFORM_DEVID_NONE here
@@ -1442,7 +1429,10 @@
 				sizeof(struct i2c_mux_gpio_platform_data));
 	if (IS_ERR(priv->mux_pdev)) {
 		gpiod_remove_lookup_table(lookup);
+		devm_kfree(dev, lookup);
 		dev_err(dev, "Failed to register i2c-mux-gpio device\n");
+	} else {
+		priv->lookup = lookup;
 	}
 
 	return PTR_ERR_OR_ZERO(priv->mux_pdev);
@@ -1493,7 +1483,6 @@
 i801_add_tco_spt(struct i801_priv *priv, struct pci_dev *pci_dev,
 		 struct resource *tco_res)
 {
-	static DEFINE_MUTEX(p2sb_mutex);
 	struct resource *res;
 	unsigned int devfn;
 	u64 base64_addr;
@@ -1506,7 +1495,7 @@
 	 * enumerated by the PCI subsystem, so we need to unhide/hide it
 	 * to lookup the P2SB BAR.
 	 */
-	mutex_lock(&p2sb_mutex);
+	pci_lock_rescan_remove();
 
 	devfn = PCI_DEVFN(PCI_SLOT(pci_dev->devfn), 1);
 
@@ -1524,7 +1513,7 @@
 	/* Hide the P2SB device, if it was hidden before */
 	if (hidden)
 		pci_bus_write_config_byte(pci_dev->bus, devfn, 0xe1, hidden);
-	mutex_unlock(&p2sb_mutex);
+	pci_unlock_rescan_remove();
 
 	res = &tco_res[1];
 	if (pci_dev->device == PCI_DEVICE_ID_INTEL_DNV_SMBUS)
@@ -1862,10 +1851,18 @@
 
 	i801_add_tco(priv);
 
+	/*
+	 * adapter.name is used by platform code to find the main I801 adapter
+	 * to instantiante i2c_clients, do not change.
+	 */
 	snprintf(priv->adapter.name, sizeof(priv->adapter.name),
-		"SMBus I801 adapter at %04lx", priv->smba);
+		 "SMBus %s adapter at %04lx",
+		 (priv->features & FEATURE_IDF) ? "I801 IDF" : "I801",
+		 priv->smba);
+
 	err = i2c_add_adapter(&priv->adapter);
 	if (err) {
+		platform_device_unregister(priv->tco_pdev);
 		i801_acpi_remove(priv);
 		return err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-ibm_iic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-ibm_iic.c
@@ -694,10 +694,8 @@
 	int ret;
 
 	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
-	if (!dev) {
-		dev_err(&ofdev->dev, "failed to allocate device data\n");
+	if (!dev)
 		return -ENOMEM;
-	}
 
 	platform_set_drvdata(ofdev, dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-imx-lpi2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-imx-lpi2c.c
@@ -99,6 +99,7 @@
 	__u8			*rx_buf;
 	__u8			*tx_buf;
 	struct completion	complete;
+	unsigned long		rate_per;
 	unsigned int		msglen;
 	unsigned int		delivered;
 	unsigned int		block_data;
@@ -200,14 +201,15 @@
 /* CLKLO = I2C_CLK_RATIO * CLKHI, SETHOLD = CLKHI, DATAVD = CLKHI/2 */
 static int lpi2c_imx_config(struct lpi2c_imx_struct *lpi2c_imx)
 {
-	u8 prescale, filt, sethold, clkhi, clklo, datavd;
-	unsigned int clk_rate, clk_cycle;
+	u8 prescale, filt, sethold, datavd;
+	unsigned int clk_rate, clk_cycle, clkhi, clklo;
 	enum lpi2c_imx_pincfg pincfg;
 	unsigned int temp;
 
 	lpi2c_imx_set_mode(lpi2c_imx);
 
-	clk_rate = clk_get_rate(lpi2c_imx->clk);
+	clk_rate = lpi2c_imx->rate_per;
+
 	if (lpi2c_imx->mode == HS || lpi2c_imx->mode == ULTRA_FAST)
 		filt = 0;
 	else
@@ -462,6 +464,8 @@
 		if (num == 1 && msgs[0].len == 0)
 			goto stop;
 
+		lpi2c_imx->rx_buf = NULL;
+		lpi2c_imx->tx_buf = NULL;
 		lpi2c_imx->delivered = 0;
 		lpi2c_imx->msglen = msgs[i].len;
 		init_completion(&lpi2c_imx->complete);
@@ -502,10 +506,14 @@
 static irqreturn_t lpi2c_imx_isr(int irq, void *dev_id)
 {
 	struct lpi2c_imx_struct *lpi2c_imx = dev_id;
+	unsigned int enabled;
 	unsigned int temp;
 
+	enabled = readl(lpi2c_imx->base + LPI2C_MIER);
+
 	lpi2c_imx_intctrl(lpi2c_imx, 0);
 	temp = readl(lpi2c_imx->base + LPI2C_MSR);
+	temp &= enabled;
 
 	if (temp & MSR_RDF)
 		lpi2c_imx_read_rxfifo(lpi2c_imx);
@@ -588,6 +596,20 @@
 		return ret;
 	}
 
+	/*
+	 * Lock the parent clock rate to avoid getting parent clock upon
+	 * each transfer
+	 */
+	ret = devm_clk_rate_exclusive_get(&pdev->dev, lpi2c_imx->clk);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret,
+				     "can't lock I2C peripheral clock rate\n");
+
+	lpi2c_imx->rate_per = clk_get_rate(lpi2c_imx->clk);
+	if (!lpi2c_imx->rate_per)
+		return dev_err_probe(&pdev->dev, -EINVAL,
+				     "can't get I2C peripheral clock rate\n");
+
 	pm_runtime_set_autosuspend_delay(&pdev->dev, I2C_PM_TIMEOUT);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_get_noresume(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-imx.c
@@ -37,6 +37,8 @@
 #include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/hrtimer.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
@@ -51,6 +53,8 @@
 /* This will be the driver name the kernel reports */
 #define DRIVER_NAME "imx-i2c"
 
+#define I2C_IMX_CHECK_DELAY 30000 /* Time to check for bus idle, in NS */
+
 /*
  * Enable DMA if transfer byte size is bigger than this threshold.
  * As the hardware request, it must bigger than 4 bytes.\
@@ -210,6 +214,10 @@
 	struct imx_i2c_dma	*dma;
 	struct i2c_client	*slave;
 	enum i2c_slave_event last_slave_event;
+
+	/* For checking slave events. */
+	spinlock_t     slave_lock;
+	struct hrtimer slave_timer;
 };
 
 static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
@@ -680,7 +688,7 @@
 
 static void i2c_imx_slave_finish_op(struct imx_i2c_struct *i2c_imx)
 {
-	u8 val;
+	u8 val = 0;
 
 	while (i2c_imx->last_slave_event != I2C_SLAVE_STOP) {
 		switch (i2c_imx->last_slave_event) {
@@ -701,10 +709,11 @@
 	}
 }
 
-static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
-				     unsigned int status, unsigned int ctl)
+/* Returns true if the timer should be restarted, false if not. */
+static irqreturn_t i2c_imx_slave_handle(struct imx_i2c_struct *i2c_imx,
+					unsigned int status, unsigned int ctl)
 {
-	u8 value;
+	u8 value = 0;
 
 	if (status & I2SR_IAL) { /* Arbitration lost */
 		i2c_imx_clear_irq(i2c_imx, I2SR_IAL);
@@ -712,6 +721,16 @@
 			return IRQ_HANDLED;
 	}
 
+	if (!(status & I2SR_IBB)) {
+		/* No master on the bus, that could mean a stop condition. */
+		i2c_imx_slave_finish_op(i2c_imx);
+		return IRQ_HANDLED;
+	}
+
+	if (!(status & I2SR_ICF))
+		/* Data transfer still in progress, ignore this. */
+		goto out;
+
 	if (status & I2SR_IAAS) { /* Addressed as a slave */
 		i2c_imx_slave_finish_op(i2c_imx);
 		if (status & I2SR_SRW) { /* Master wants to read from us*/
@@ -737,16 +756,9 @@
 			imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
 		}
 	} else if (!(ctl & I2CR_MTX)) { /* Receive mode */
-		if (status & I2SR_IBB) { /* No STOP signal detected */
-			value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
-			i2c_imx_slave_event(i2c_imx,
-					    I2C_SLAVE_WRITE_RECEIVED, &value);
-		} else { /* STOP signal is detected */
-			dev_dbg(&i2c_imx->adapter.dev,
-				"STOP signal detected");
-			i2c_imx_slave_event(i2c_imx,
-					    I2C_SLAVE_STOP, &value);
-		}
+		value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
+		i2c_imx_slave_event(i2c_imx,
+				    I2C_SLAVE_WRITE_RECEIVED, &value);
 	} else if (!(status & I2SR_RXAK)) { /* Transmit mode received ACK */
 		ctl |= I2CR_MTX;
 		imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
@@ -755,15 +767,48 @@
 				    I2C_SLAVE_READ_PROCESSED, &value);
 
 		imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
-	} else { /* Transmit mode received NAK */
+	} else { /* Transmit mode received NAK, operation is done */
 		ctl &= ~I2CR_MTX;
 		imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
 		imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
+
+		/* flag the last byte as processed */
+		i2c_imx_slave_event(i2c_imx,
+				    I2C_SLAVE_READ_PROCESSED, &value);
+
+		i2c_imx_slave_finish_op(i2c_imx);
+		return IRQ_HANDLED;
 	}
 
+out:
+	/*
+	 * No need to check the return value here.  If it returns 0 or
+	 * 1, then everything is fine.  If it returns -1, then the
+	 * timer is running in the handler.  This will still work,
+	 * though it may be redone (or already have been done) by the
+	 * timer function.
+	 */
+	hrtimer_try_to_cancel(&i2c_imx->slave_timer);
+	hrtimer_forward_now(&i2c_imx->slave_timer, I2C_IMX_CHECK_DELAY);
+	hrtimer_restart(&i2c_imx->slave_timer);
 	return IRQ_HANDLED;
 }
 
+static enum hrtimer_restart i2c_imx_slave_timeout(struct hrtimer *t)
+{
+	struct imx_i2c_struct *i2c_imx = container_of(t, struct imx_i2c_struct,
+						      slave_timer);
+	unsigned int ctl, status;
+	unsigned long flags;
+
+	spin_lock_irqsave(&i2c_imx->slave_lock, flags);
+	status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
+	ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+	i2c_imx_slave_handle(i2c_imx, status, ctl);
+	spin_unlock_irqrestore(&i2c_imx->slave_lock, flags);
+	return HRTIMER_NORESTART;
+}
+
 static void i2c_imx_slave_init(struct imx_i2c_struct *i2c_imx)
 {
 	int temp;
@@ -843,7 +888,9 @@
 {
 	struct imx_i2c_struct *i2c_imx = dev_id;
 	unsigned int ctl, status;
+	unsigned long flags;
 
+	spin_lock_irqsave(&i2c_imx->slave_lock, flags);
 	status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 	ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 
@@ -851,14 +898,20 @@
 		i2c_imx_clear_irq(i2c_imx, I2SR_IIF);
 		if (i2c_imx->slave) {
 			if (!(ctl & I2CR_MSTA)) {
-				return i2c_imx_slave_isr(i2c_imx, status, ctl);
-			} else if (i2c_imx->last_slave_event !=
-				   I2C_SLAVE_STOP) {
-				i2c_imx_slave_finish_op(i2c_imx);
+				irqreturn_t ret;
+
+				ret = i2c_imx_slave_handle(i2c_imx,
+							   status, ctl);
+				spin_unlock_irqrestore(&i2c_imx->slave_lock,
+						       flags);
+				return ret;
 			}
+			i2c_imx_slave_finish_op(i2c_imx);
 		}
+		spin_unlock_irqrestore(&i2c_imx->slave_lock, flags);
 		return i2c_imx_master_isr(i2c_imx, status);
 	}
+	spin_unlock_irqrestore(&i2c_imx->slave_lock, flags);
 
 	return IRQ_NONE;
 }
@@ -1051,7 +1104,8 @@
 	int i, result;
 	unsigned int temp;
 	int block_data = msgs->flags & I2C_M_RECV_LEN;
-	int use_dma = i2c_imx->dma && msgs->len >= DMA_THRESHOLD && !block_data;
+	int use_dma = i2c_imx->dma && msgs->flags & I2C_M_DMA_SAFE &&
+		msgs->len >= DMA_THRESHOLD && !block_data;
 
 	dev_dbg(&i2c_imx->adapter.dev,
 		"<%s> write slave address: addr=0x%x\n",
@@ -1217,7 +1271,8 @@
 			result = i2c_imx_read(i2c_imx, &msgs[i], is_lastmsg, atomic);
 		} else {
 			if (!atomic &&
-			    i2c_imx->dma && msgs[i].len >= DMA_THRESHOLD)
+			    i2c_imx->dma && msgs[i].len >= DMA_THRESHOLD &&
+				msgs[i].flags & I2C_M_DMA_SAFE)
 				result = i2c_imx_dma_write(i2c_imx, &msgs[i]);
 			else
 				result = i2c_imx_write(i2c_imx, &msgs[i], atomic);
@@ -1378,6 +1433,10 @@
 	if (!i2c_imx)
 		return -ENOMEM;
 
+	spin_lock_init(&i2c_imx->slave_lock);
+	hrtimer_init(&i2c_imx->slave_timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
+	i2c_imx->slave_timer.function = i2c_imx_slave_timeout;
+
 	match = device_get_match_data(&pdev->dev);
 	if (match)
 		i2c_imx->hwdata = match;
@@ -1487,9 +1546,9 @@
 	struct imx_i2c_struct *i2c_imx = platform_get_drvdata(pdev);
 	int irq, ret;
 
-	ret = pm_runtime_resume_and_get(&pdev->dev);
-	if (ret < 0)
-		return ret;
+	ret = pm_runtime_get_sync(&pdev->dev);
+
+	hrtimer_cancel(&i2c_imx->slave_timer);
 
 	/* remove adapter */
 	dev_dbg(&i2c_imx->adapter.dev, "adapter removed\n");
@@ -1498,17 +1557,21 @@
 	if (i2c_imx->dma)
 		i2c_imx_dma_free(i2c_imx);
 
-	/* setup chip registers to defaults */
-	imx_i2c_write_reg(0, i2c_imx, IMX_I2C_IADR);
-	imx_i2c_write_reg(0, i2c_imx, IMX_I2C_IFDR);
-	imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2CR);
-	imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2SR);
+	if (ret >= 0) {
+		/* setup chip registers to defaults */
+		imx_i2c_write_reg(0, i2c_imx, IMX_I2C_IADR);
+		imx_i2c_write_reg(0, i2c_imx, IMX_I2C_IFDR);
+		imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2CR);
+		imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2SR);
+		clk_disable(i2c_imx->clk);
+	}
 
 	clk_notifier_unregister(i2c_imx->clk, &i2c_imx->clk_change_nb);
 	irq = platform_get_irq(pdev, 0);
 	if (irq >= 0)
 		free_irq(irq, i2c_imx);
-	clk_disable_unprepare(i2c_imx->clk);
+
+	clk_unprepare(i2c_imx->clk);
 
 	pm_runtime_put_noidle(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-isch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-isch.c
@@ -99,8 +99,7 @@
 	if (retries > MAX_RETRIES) {
 		dev_err(&sch_adapter.dev, "SMBus Timeout!\n");
 		result = -ETIMEDOUT;
-	}
-	if (temp & 0x04) {
+	} else if (temp & 0x04) {
 		result = -EIO;
 		dev_dbg(&sch_adapter.dev, "Bus collision! SMBus may be "
 			"locked until next hard reset. (sorry!)\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-ismt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-ismt.c
@@ -82,6 +82,7 @@
 
 #define ISMT_DESC_ENTRIES	2	/* number of descriptor entries */
 #define ISMT_MAX_RETRIES	3	/* number of SMBus retries to attempt */
+#define ISMT_LOG_ENTRIES	3	/* number of interrupt cause log entries */
 
 /* Hardware Descriptor Constants - Control Field */
 #define ISMT_DESC_CWRL	0x01	/* Command/Write Length */
@@ -175,6 +176,8 @@
 	u8 head;				/* ring buffer head pointer */
 	struct completion cmp;			/* interrupt completion */
 	u8 buffer[I2C_SMBUS_BLOCK_MAX + 16];	/* temp R/W data buffer */
+	dma_addr_t log_dma;
+	u32 *log;
 };
 
 static const struct pci_device_id ismt_ids[] = {
@@ -411,6 +414,9 @@
 	memset(desc, 0, sizeof(struct ismt_desc));
 	desc->tgtaddr_rw = ISMT_DESC_ADDR_RW(addr, read_write);
 
+	/* Always clear the log entries */
+	memset(priv->log, 0, ISMT_LOG_ENTRIES * sizeof(u32));
+
 	/* Initialize common control bits */
 	if (likely(pci_dev_msi_enabled(priv->pci_dev)))
 		desc->control = ISMT_DESC_INT | ISMT_DESC_FAIR;
@@ -503,6 +509,9 @@
 		if (read_write == I2C_SMBUS_WRITE) {
 			/* Block Write */
 			dev_dbg(dev, "I2C_SMBUS_BLOCK_DATA:  WRITE\n");
+			if (data->block[0] < 1 || data->block[0] > I2C_SMBUS_BLOCK_MAX)
+				return -EINVAL;
+
 			dma_size = data->block[0] + 1;
 			dma_direction = DMA_TO_DEVICE;
 			desc->wr_len_cmd = dma_size;
@@ -522,6 +531,9 @@
 
 	case I2C_SMBUS_BLOCK_PROC_CALL:
 		dev_dbg(dev, "I2C_SMBUS_BLOCK_PROC_CALL\n");
+		if (data->block[0] > I2C_SMBUS_BLOCK_MAX)
+			return -EINVAL;
+
 		dma_size = I2C_SMBUS_BLOCK_MAX;
 		desc->tgtaddr_rw = ISMT_DESC_ADDR_RW(addr, 1);
 		desc->wr_len_cmd = data->block[0] + 1;
@@ -708,6 +720,8 @@
 	/* initialize the Master Descriptor Base Address (MDBA) */
 	writeq(priv->io_rng_dma, priv->smba + ISMT_MSTR_MDBA);
 
+	writeq(priv->log_dma, priv->smba + ISMT_GR_SMTICL);
+
 	/* initialize the Master Control Register (MCTRL) */
 	writel(ISMT_MCTRL_MEIE, priv->smba + ISMT_MSTR_MCTRL);
 
@@ -795,6 +809,12 @@
 	priv->head = 0;
 	init_completion(&priv->cmp);
 
+	priv->log = dmam_alloc_coherent(&priv->pci_dev->dev,
+					ISMT_LOG_ENTRIES * sizeof(u32),
+					&priv->log_dma, GFP_KERNEL);
+	if (!priv->log)
+		return -ENOMEM;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-ljca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-ljca.c
@@ -0,0 +1,422 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Intel La Jolla Cove Adapter USB-I2C driver
+ *
+ * Copyright (c) 2021, Intel Corporation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/i2c.h>
+#include <linux/mfd/ljca.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+/* I2C commands */
+enum i2c_cmd {
+	I2C_INIT = 1,
+	I2C_XFER,
+	I2C_START,
+	I2C_STOP,
+	I2C_READ,
+	I2C_WRITE,
+};
+
+enum i2c_address_mode {
+	I2C_ADDRESS_MODE_7BIT,
+	I2C_ADDRESS_MODE_10BIT,
+};
+
+enum xfer_type {
+	READ_XFER_TYPE,
+	WRITE_XFER_TYPE,
+};
+
+#define DEFAULT_I2C_CONTROLLER_ID 1
+#define DEFAULT_I2C_CAPACITY 0
+#define DEFAULT_I2C_INTR_PIN 0
+
+/* I2C r/w Flags */
+#define I2C_SLAVE_TRANSFER_WRITE (0)
+#define I2C_SLAVE_TRANSFER_READ (1)
+
+/* i2c init flags */
+#define I2C_INIT_FLAG_MODE_MASK (0x1 << 0)
+#define I2C_INIT_FLAG_MODE_POLLING (0x0 << 0)
+#define I2C_INIT_FLAG_MODE_INTERRUPT (0x1 << 0)
+
+#define I2C_FLAG_ADDR_16BIT (0x1 << 0)
+
+#define I2C_INIT_FLAG_FREQ_MASK (0x3 << 1)
+#define I2C_FLAG_FREQ_100K (0x0 << 1)
+#define I2C_FLAG_FREQ_400K (0x1 << 1)
+#define I2C_FLAG_FREQ_1M (0x2 << 1)
+
+/* I2C Transfer */
+struct i2c_xfer {
+	u8 id;
+	u8 slave;
+	u16 flag; /* speed, 8/16bit addr, addr increase, etc */
+	u16 addr;
+	u16 len;
+	u8 data[];
+} __packed;
+
+/* I2C raw commands: Init/Start/Read/Write/Stop */
+struct i2c_rw_packet {
+	u8 id;
+	__le16 len;
+	u8 data[];
+} __packed;
+
+#define LJCA_I2C_MAX_XFER_SIZE 256
+#define LJCA_I2C_BUF_SIZE                                                      \
+	(LJCA_I2C_MAX_XFER_SIZE + sizeof(struct i2c_rw_packet))
+
+struct ljca_i2c_dev {
+	struct platform_device *pdev;
+	struct ljca_i2c_info *ctr_info;
+	struct i2c_adapter adap;
+
+	u8 obuf[LJCA_I2C_BUF_SIZE];
+	u8 ibuf[LJCA_I2C_BUF_SIZE];
+};
+
+static u8 ljca_i2c_format_slave_addr(u8 slave_addr, enum i2c_address_mode mode)
+{
+	if (mode == I2C_ADDRESS_MODE_7BIT)
+		return slave_addr << 1;
+
+	return 0xFF;
+}
+
+static int ljca_i2c_init(struct ljca_i2c_dev *ljca_i2c, u8 id)
+{
+	struct i2c_rw_packet *w_packet = (struct i2c_rw_packet *)ljca_i2c->obuf;
+
+	memset(w_packet, 0, sizeof(*w_packet));
+	w_packet->id = id;
+	w_packet->len = cpu_to_le16(1);
+	w_packet->data[0] = I2C_FLAG_FREQ_400K;
+
+	return ljca_transfer(ljca_i2c->pdev, I2C_INIT, w_packet,
+			     sizeof(*w_packet) + 1, NULL, NULL);
+}
+
+static int ljca_i2c_start(struct ljca_i2c_dev *ljca_i2c, u8 slave_addr,
+			  enum xfer_type type)
+{
+	struct i2c_rw_packet *w_packet = (struct i2c_rw_packet *)ljca_i2c->obuf;
+	struct i2c_rw_packet *r_packet = (struct i2c_rw_packet *)ljca_i2c->ibuf;
+	int ret;
+	int ibuf_len;
+
+	memset(w_packet, 0, sizeof(*w_packet));
+	w_packet->id = ljca_i2c->ctr_info->id;
+	w_packet->len = cpu_to_le16(1);
+	w_packet->data[0] =
+		ljca_i2c_format_slave_addr(slave_addr, I2C_ADDRESS_MODE_7BIT);
+	w_packet->data[0] |= (type == READ_XFER_TYPE) ?
+					   I2C_SLAVE_TRANSFER_READ :
+					   I2C_SLAVE_TRANSFER_WRITE;
+
+	ret = ljca_transfer(ljca_i2c->pdev, I2C_START, w_packet,
+			    sizeof(*w_packet) + 1, r_packet, &ibuf_len);
+
+	if (ret || ibuf_len < sizeof(*r_packet))
+		return -EIO;
+
+	if ((s16)le16_to_cpu(r_packet->len) < 0 ||
+	    r_packet->id != w_packet->id) {
+		dev_err(&ljca_i2c->adap.dev,
+			"i2c start failed len:%d id:%d %d\n",
+			(s16)le16_to_cpu(r_packet->len), r_packet->id,
+			w_packet->id);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int ljca_i2c_stop(struct ljca_i2c_dev *ljca_i2c, u8 slave_addr)
+{
+	struct i2c_rw_packet *w_packet = (struct i2c_rw_packet *)ljca_i2c->obuf;
+	struct i2c_rw_packet *r_packet = (struct i2c_rw_packet *)ljca_i2c->ibuf;
+	int ret;
+	int ibuf_len;
+
+	memset(w_packet, 0, sizeof(*w_packet));
+	w_packet->id = ljca_i2c->ctr_info->id;
+	w_packet->len = cpu_to_le16(1);
+	w_packet->data[0] = 0;
+
+	ret = ljca_transfer(ljca_i2c->pdev, I2C_STOP, w_packet,
+			    sizeof(*w_packet) + 1, r_packet, &ibuf_len);
+
+	if (ret || ibuf_len < sizeof(*r_packet))
+		return -EIO;
+
+	if ((s16)le16_to_cpu(r_packet->len) < 0 ||
+	    r_packet->id != w_packet->id) {
+		dev_err(&ljca_i2c->adap.dev,
+			"i2c stop failed len:%d id:%d %d\n",
+			(s16)le16_to_cpu(r_packet->len), r_packet->id,
+			w_packet->id);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int ljca_i2c_pure_read(struct ljca_i2c_dev *ljca_i2c, u8 *data, int len)
+{
+	struct i2c_rw_packet *w_packet = (struct i2c_rw_packet *)ljca_i2c->obuf;
+	struct i2c_rw_packet *r_packet = (struct i2c_rw_packet *)ljca_i2c->ibuf;
+	int ibuf_len;
+	int ret;
+
+	if (len > LJCA_I2C_MAX_XFER_SIZE)
+		return -EINVAL;
+
+	memset(w_packet, 0, sizeof(*w_packet));
+	w_packet->id = ljca_i2c->ctr_info->id;
+	w_packet->len = cpu_to_le16(len);
+	ret = ljca_transfer(ljca_i2c->pdev, I2C_READ, w_packet,
+			    sizeof(*w_packet) + 1, r_packet, &ibuf_len);
+	if (ret) {
+		dev_err(&ljca_i2c->adap.dev, "I2C_READ failed ret:%d\n", ret);
+		return ret;
+	}
+
+	if (ibuf_len < sizeof(*r_packet))
+		return -EIO;
+
+	if ((s16)le16_to_cpu(r_packet->len) != len ||
+	    r_packet->id != w_packet->id) {
+		dev_err(&ljca_i2c->adap.dev,
+			"i2c raw read failed len:%d id:%d %d\n",
+			(s16)le16_to_cpu(r_packet->len), r_packet->id,
+			w_packet->id);
+		return -EIO;
+	}
+
+	memcpy(data, r_packet->data, len);
+
+	return 0;
+}
+
+static int ljca_i2c_read(struct ljca_i2c_dev *ljca_i2c, u8 slave_addr, u8 *data,
+			 u8 len)
+{
+	int ret;
+
+	ret = ljca_i2c_start(ljca_i2c, slave_addr, READ_XFER_TYPE);
+	if (ret)
+		return ret;
+
+	ret = ljca_i2c_pure_read(ljca_i2c, data, len);
+	if (ret) {
+		dev_err(&ljca_i2c->adap.dev, "i2c raw read failed ret:%d\n",
+			ret);
+
+		return ret;
+	}
+
+	return ljca_i2c_stop(ljca_i2c, slave_addr);
+}
+
+static int ljca_i2c_pure_write(struct ljca_i2c_dev *ljca_i2c, u8 *data, u8 len)
+{
+	struct i2c_rw_packet *w_packet = (struct i2c_rw_packet *)ljca_i2c->obuf;
+	struct i2c_rw_packet *r_packet = (struct i2c_rw_packet *)ljca_i2c->ibuf;
+	int ret;
+	int ibuf_len;
+
+	if (len > LJCA_I2C_MAX_XFER_SIZE)
+		return -EINVAL;
+
+	memset(w_packet, 0, sizeof(*w_packet));
+	w_packet->id = ljca_i2c->ctr_info->id;
+	w_packet->len = cpu_to_le16(len);
+	memcpy(w_packet->data, data, len);
+
+	ret = ljca_transfer(ljca_i2c->pdev, I2C_WRITE, w_packet,
+			    sizeof(*w_packet) + w_packet->len, r_packet,
+			    &ibuf_len);
+
+	if (ret || ibuf_len < sizeof(*r_packet))
+		return -EIO;
+
+	if ((s16)le16_to_cpu(r_packet->len) != len ||
+	    r_packet->id != w_packet->id) {
+		dev_err(&ljca_i2c->adap.dev,
+			"i2c write failed len:%d id:%d/%d\n",
+			(s16)le16_to_cpu(r_packet->len), r_packet->id,
+			w_packet->id);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int ljca_i2c_write(struct ljca_i2c_dev *ljca_i2c, u8 slave_addr,
+			  u8 *data, u8 len)
+{
+	int ret;
+
+	if (!data)
+		return -EINVAL;
+
+	ret = ljca_i2c_start(ljca_i2c, slave_addr, WRITE_XFER_TYPE);
+	if (ret)
+		return ret;
+
+	ret = ljca_i2c_pure_write(ljca_i2c, data, len);
+	if (ret)
+		return ret;
+
+	return ljca_i2c_stop(ljca_i2c, slave_addr);
+}
+
+static int ljca_i2c_xfer(struct i2c_adapter *adapter, struct i2c_msg *msg,
+			 int num)
+{
+	struct ljca_i2c_dev *ljca_i2c;
+	struct i2c_msg *cur_msg;
+	int i, ret;
+
+	ljca_i2c = i2c_get_adapdata(adapter);
+	if (!ljca_i2c)
+		return -EINVAL;
+
+	for (i = 0; i < num; i++) {
+		cur_msg = &msg[i];
+		dev_dbg(&adapter->dev, "i:%d msg:(%d %d)\n", i, cur_msg->flags,
+			cur_msg->len);
+		if (cur_msg->flags & I2C_M_RD)
+			ret = ljca_i2c_read(ljca_i2c, cur_msg->addr,
+					    cur_msg->buf, cur_msg->len);
+
+		else
+			ret = ljca_i2c_write(ljca_i2c, cur_msg->addr,
+					     cur_msg->buf, cur_msg->len);
+
+		if (ret)
+			return ret;
+	}
+
+	return num;
+}
+
+static u32 ljca_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_adapter_quirks ljca_i2c_quirks = {
+	.max_read_len = LJCA_I2C_MAX_XFER_SIZE,
+	.max_write_len = LJCA_I2C_MAX_XFER_SIZE,
+};
+
+static const struct i2c_algorithm ljca_i2c_algo = {
+	.master_xfer = ljca_i2c_xfer,
+	.functionality = ljca_i2c_func,
+};
+
+static void try_bind_acpi(struct platform_device *pdev,
+			  struct ljca_i2c_dev *ljca_i2c)
+{
+	struct acpi_device *parent, *child;
+	struct acpi_device *cur = ACPI_COMPANION(&pdev->dev);
+	const char *hid1;
+	const char *uid1;
+	char uid2[2] = { 0 };
+
+	if (!cur)
+		return;
+
+	hid1 = acpi_device_hid(cur);
+	uid1 = acpi_device_uid(cur);
+	snprintf(uid2, sizeof(uid2), "%d", ljca_i2c->ctr_info->id);
+
+	/*
+	* If the pdev is bound to the right acpi device, just forward it to the
+	* adapter. Otherwise, we find that of current adapter manually.
+	*/
+	if (!uid1 || !strcmp(uid1, uid2)) {
+		ACPI_COMPANION_SET(&ljca_i2c->adap.dev, cur);
+		return;
+	}
+
+	dev_dbg(&pdev->dev, "hid %s uid %s new uid%s\n", hid1, uid1, uid2);
+	parent = ACPI_COMPANION(pdev->dev.parent);
+	if (!parent)
+		return;
+
+	list_for_each_entry(child, &parent->children, node) {
+		if (acpi_dev_hid_uid_match(child, hid1, uid2)) {
+			ACPI_COMPANION_SET(&ljca_i2c->adap.dev, child);
+			return;
+		}
+	}
+}
+
+static int ljca_i2c_probe(struct platform_device *pdev)
+{
+	struct ljca_i2c_dev *ljca_i2c;
+	struct ljca_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	int ret;
+
+	ljca_i2c = devm_kzalloc(&pdev->dev, sizeof(*ljca_i2c), GFP_KERNEL);
+	if (!ljca_i2c)
+		return -ENOMEM;
+
+	ljca_i2c->pdev = pdev;
+	ljca_i2c->ctr_info = &pdata->i2c_info;
+
+	ljca_i2c->adap.owner = THIS_MODULE;
+	ljca_i2c->adap.class = I2C_CLASS_HWMON;
+	ljca_i2c->adap.algo = &ljca_i2c_algo;
+	ljca_i2c->adap.dev.parent = &pdev->dev;
+
+	try_bind_acpi(pdev, ljca_i2c);
+
+	ljca_i2c->adap.dev.of_node = pdev->dev.of_node;
+	i2c_set_adapdata(&ljca_i2c->adap, ljca_i2c);
+	snprintf(ljca_i2c->adap.name, sizeof(ljca_i2c->adap.name), "%s-%s-%d",
+		 "ljca-i2c", dev_name(pdev->dev.parent),
+		 ljca_i2c->ctr_info->id);
+
+	platform_set_drvdata(pdev, ljca_i2c);
+
+	ret = ljca_i2c_init(ljca_i2c, ljca_i2c->ctr_info->id);
+	if (ret) {
+		dev_err(&pdev->dev, "i2c init failed id:%d\n",
+			ljca_i2c->ctr_info->id);
+		return -EIO;
+	}
+
+	return i2c_add_adapter(&ljca_i2c->adap);
+}
+
+static int ljca_i2c_remove(struct platform_device *pdev)
+{
+	struct ljca_i2c_dev *ljca_i2c = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&ljca_i2c->adap);
+
+	return 0;
+}
+
+static struct platform_driver ljca_i2c_driver = {
+	.driver.name = "ljca-i2c",
+	.probe = ljca_i2c_probe,
+	.remove = ljca_i2c_remove,
+};
+
+module_platform_driver(ljca_i2c_driver);
+
+MODULE_AUTHOR("Ye Xiang <xiang.ye@intel.com>");
+MODULE_AUTHOR("Zhang Lixu <lixu.zhang@intel.com>");
+MODULE_DESCRIPTION("Intel La Jolla Cove Adapter USB-I2C driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ljca-i2c");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-meson.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-meson.c
@@ -465,18 +465,18 @@
 	 */
 	meson_i2c_set_mask(i2c, REG_CTRL, REG_CTRL_START, 0);
 
-	ret = i2c_add_adapter(&i2c->adap);
-	if (ret < 0) {
-		clk_disable_unprepare(i2c->clk);
-		return ret;
-	}
-
 	/* Disable filtering */
 	meson_i2c_set_mask(i2c, REG_SLAVE_ADDR,
 			   REG_SLV_SDA_FILTER | REG_SLV_SCL_FILTER, 0);
 
 	meson_i2c_set_clk_div(i2c, timings.bus_freq_hz);
 
+	ret = i2c_add_adapter(&i2c->adap);
+	if (ret < 0) {
+		clk_disable_unprepare(i2c->clk);
+		return ret;
+	}
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mlxbf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mlxbf.c
@@ -6,6 +6,7 @@
  */
 
 #include <linux/acpi.h>
+#include <linux/bitfield.h>
 #include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/interrupt.h>
@@ -63,13 +64,14 @@
  */
 #define MLXBF_I2C_TYU_PLL_OUT_FREQ  (400 * 1000 * 1000)
 /* Reference clock for Bluefield - 156 MHz. */
-#define MLXBF_I2C_PLL_IN_FREQ       (156 * 1000 * 1000)
+#define MLXBF_I2C_PLL_IN_FREQ       156250000ULL
 
 /* Constant used to determine the PLL frequency. */
-#define MLNXBF_I2C_COREPLL_CONST    16384
+#define MLNXBF_I2C_COREPLL_CONST    16384ULL
+
+#define MLXBF_I2C_FREQUENCY_1GHZ  1000000000ULL
 
 /* PLL registers. */
-#define MLXBF_I2C_CORE_PLL_REG0         0x0
 #define MLXBF_I2C_CORE_PLL_REG1         0x4
 #define MLXBF_I2C_CORE_PLL_REG2         0x8
 
@@ -181,22 +183,15 @@
 #define MLXBF_I2C_COREPLL_FREQ          MLXBF_I2C_TYU_PLL_OUT_FREQ
 
 /* Core PLL TYU configuration. */
-#define MLXBF_I2C_COREPLL_CORE_F_TYU_MASK   GENMASK(12, 0)
-#define MLXBF_I2C_COREPLL_CORE_OD_TYU_MASK  GENMASK(3, 0)
-#define MLXBF_I2C_COREPLL_CORE_R_TYU_MASK   GENMASK(5, 0)
-
-#define MLXBF_I2C_COREPLL_CORE_F_TYU_SHIFT  3
-#define MLXBF_I2C_COREPLL_CORE_OD_TYU_SHIFT 16
-#define MLXBF_I2C_COREPLL_CORE_R_TYU_SHIFT  20
+#define MLXBF_I2C_COREPLL_CORE_F_TYU_MASK   GENMASK(15, 3)
+#define MLXBF_I2C_COREPLL_CORE_OD_TYU_MASK  GENMASK(19, 16)
+#define MLXBF_I2C_COREPLL_CORE_R_TYU_MASK   GENMASK(25, 20)
 
 /* Core PLL YU configuration. */
 #define MLXBF_I2C_COREPLL_CORE_F_YU_MASK    GENMASK(25, 0)
 #define MLXBF_I2C_COREPLL_CORE_OD_YU_MASK   GENMASK(3, 0)
-#define MLXBF_I2C_COREPLL_CORE_R_YU_MASK    GENMASK(5, 0)
+#define MLXBF_I2C_COREPLL_CORE_R_YU_MASK    GENMASK(31, 26)
 
-#define MLXBF_I2C_COREPLL_CORE_F_YU_SHIFT   0
-#define MLXBF_I2C_COREPLL_CORE_OD_YU_SHIFT  1
-#define MLXBF_I2C_COREPLL_CORE_R_YU_SHIFT   26
 
 /* Core PLL frequency. */
 static u64 mlxbf_i2c_corepll_frequency;
@@ -311,6 +306,7 @@
  * exact.
  */
 #define MLXBF_I2C_SMBUS_TIMEOUT   (300 * 1000) /* 300ms */
+#define MLXBF_I2C_SMBUS_LOCK_POLL_TIMEOUT (300 * 1000) /* 300ms */
 
 /* Encapsulates timing parameters. */
 struct mlxbf_i2c_timings {
@@ -479,8 +475,6 @@
 #define MLXBF_I2C_MASK_8    GENMASK(7, 0)
 #define MLXBF_I2C_MASK_16   GENMASK(15, 0)
 
-#define MLXBF_I2C_FREQUENCY_1GHZ  1000000000
-
 /*
  * Function to poll a set of bits at a specific address; it checks whether
  * the bits are equal to zero when eq_zero is set to 'true', and not equal
@@ -521,6 +515,25 @@
 	return false;
 }
 
+/*
+ * wait for the lock to be released before acquiring it.
+ */
+static bool mlxbf_i2c_smbus_master_lock(struct mlxbf_i2c_priv *priv)
+{
+	if (mlxbf_smbus_poll(priv->smbus->io, MLXBF_I2C_SMBUS_MASTER_GW,
+			   MLXBF_I2C_MASTER_LOCK_BIT, true,
+			   MLXBF_I2C_SMBUS_LOCK_POLL_TIMEOUT))
+		return true;
+
+	return false;
+}
+
+static void mlxbf_i2c_smbus_master_unlock(struct mlxbf_i2c_priv *priv)
+{
+	/* Clear the gw to clear the lock */
+	writel(0, priv->smbus->io + MLXBF_I2C_SMBUS_MASTER_GW);
+}
+
 static bool mlxbf_i2c_smbus_transaction_success(u32 master_status,
 						u32 cause_status)
 {
@@ -669,7 +682,7 @@
 	/* Clear status bits. */
 	writel(0x0, priv->smbus->io + MLXBF_I2C_SMBUS_MASTER_STATUS);
 	/* Set the cause data. */
-	writel(~0x0, priv->smbus->io + MLXBF_I2C_CAUSE_OR_CLEAR);
+	writel(~0x0, priv->mst_cause->io + MLXBF_I2C_CAUSE_OR_CLEAR);
 	/* Zero PEC byte. */
 	writel(0x0, priv->smbus->io + MLXBF_I2C_SMBUS_MASTER_PEC);
 	/* Zero byte count. */
@@ -712,10 +725,19 @@
 	slave = request->slave & GENMASK(6, 0);
 	addr = slave << 1;
 
-	/* First of all, check whether the HW is idle. */
-	if (WARN_ON(!mlxbf_smbus_master_wait_for_idle(priv)))
+	/*
+	 * Try to acquire the smbus gw lock before any reads of the GW register since
+	 * a read sets the lock.
+	 */
+	if (WARN_ON(!mlxbf_i2c_smbus_master_lock(priv)))
 		return -EBUSY;
 
+	/* Check whether the HW is idle */
+	if (WARN_ON(!mlxbf_smbus_master_wait_for_idle(priv))) {
+		ret = -EBUSY;
+		goto out_unlock;
+	}
+
 	/* Set first byte. */
 	data_desc[data_idx++] = addr;
 
@@ -738,6 +760,11 @@
 		if (flags & MLXBF_I2C_F_WRITE) {
 			write_en = 1;
 			write_len += operation->length;
+			if (data_idx + operation->length >
+					MLXBF_I2C_MASTER_DATA_DESC_SIZE) {
+				ret = -ENOBUFS;
+				goto out_unlock;
+			}
 			memcpy(data_desc + data_idx,
 			       operation->buffer, operation->length);
 			data_idx += operation->length;
@@ -769,7 +796,7 @@
 		ret = mlxbf_i2c_smbus_enable(priv, slave, write_len, block_en,
 					 pec_en, 0);
 		if (ret)
-			return ret;
+			goto out_unlock;
 	}
 
 	if (read_en) {
@@ -796,6 +823,9 @@
 			priv->smbus->io + MLXBF_I2C_SMBUS_MASTER_FSM);
 	}
 
+out_unlock:
+	mlxbf_i2c_smbus_master_unlock(priv);
+
 	return ret;
 }
 
@@ -1407,24 +1437,19 @@
 	return 0;
 }
 
-static u64 mlxbf_calculate_freq_from_tyu(struct mlxbf_i2c_resource *corepll_res)
+static u64 mlxbf_i2c_calculate_freq_from_tyu(struct mlxbf_i2c_resource *corepll_res)
 {
-	u64 core_frequency, pad_frequency;
+	u64 core_frequency;
 	u8 core_od, core_r;
 	u32 corepll_val;
 	u16 core_f;
 
-	pad_frequency = MLXBF_I2C_PLL_IN_FREQ;
-
 	corepll_val = readl(corepll_res->io + MLXBF_I2C_CORE_PLL_REG1);
 
 	/* Get Core PLL configuration bits. */
-	core_f = rol32(corepll_val, MLXBF_I2C_COREPLL_CORE_F_TYU_SHIFT) &
-			MLXBF_I2C_COREPLL_CORE_F_TYU_MASK;
-	core_od = rol32(corepll_val, MLXBF_I2C_COREPLL_CORE_OD_TYU_SHIFT) &
-			MLXBF_I2C_COREPLL_CORE_OD_TYU_MASK;
-	core_r = rol32(corepll_val, MLXBF_I2C_COREPLL_CORE_R_TYU_SHIFT) &
-			MLXBF_I2C_COREPLL_CORE_R_TYU_MASK;
+	core_f = FIELD_GET(MLXBF_I2C_COREPLL_CORE_F_TYU_MASK, corepll_val);
+	core_od = FIELD_GET(MLXBF_I2C_COREPLL_CORE_OD_TYU_MASK, corepll_val);
+	core_r = FIELD_GET(MLXBF_I2C_COREPLL_CORE_R_TYU_MASK, corepll_val);
 
 	/*
 	 * Compute PLL output frequency as follow:
@@ -1436,31 +1461,26 @@
 	 * Where PLL_OUT_FREQ and PLL_IN_FREQ refer to CoreFrequency
 	 * and PadFrequency, respectively.
 	 */
-	core_frequency = pad_frequency * (++core_f);
+	core_frequency = MLXBF_I2C_PLL_IN_FREQ * (++core_f);
 	core_frequency /= (++core_r) * (++core_od);
 
 	return core_frequency;
 }
 
-static u64 mlxbf_calculate_freq_from_yu(struct mlxbf_i2c_resource *corepll_res)
+static u64 mlxbf_i2c_calculate_freq_from_yu(struct mlxbf_i2c_resource *corepll_res)
 {
 	u32 corepll_reg1_val, corepll_reg2_val;
-	u64 corepll_frequency, pad_frequency;
+	u64 corepll_frequency;
 	u8 core_od, core_r;
 	u32 core_f;
 
-	pad_frequency = MLXBF_I2C_PLL_IN_FREQ;
-
 	corepll_reg1_val = readl(corepll_res->io + MLXBF_I2C_CORE_PLL_REG1);
 	corepll_reg2_val = readl(corepll_res->io + MLXBF_I2C_CORE_PLL_REG2);
 
 	/* Get Core PLL configuration bits */
-	core_f = rol32(corepll_reg1_val, MLXBF_I2C_COREPLL_CORE_F_YU_SHIFT) &
-			MLXBF_I2C_COREPLL_CORE_F_YU_MASK;
-	core_r = rol32(corepll_reg1_val, MLXBF_I2C_COREPLL_CORE_R_YU_SHIFT) &
-			MLXBF_I2C_COREPLL_CORE_R_YU_MASK;
-	core_od = rol32(corepll_reg2_val,  MLXBF_I2C_COREPLL_CORE_OD_YU_SHIFT) &
-			MLXBF_I2C_COREPLL_CORE_OD_YU_MASK;
+	core_f = FIELD_GET(MLXBF_I2C_COREPLL_CORE_F_YU_MASK, corepll_reg1_val);
+	core_r = FIELD_GET(MLXBF_I2C_COREPLL_CORE_R_YU_MASK, corepll_reg1_val);
+	core_od = FIELD_GET(MLXBF_I2C_COREPLL_CORE_OD_YU_MASK, corepll_reg2_val);
 
 	/*
 	 * Compute PLL output frequency as follow:
@@ -1472,7 +1492,7 @@
 	 * Where PLL_OUT_FREQ and PLL_IN_FREQ refer to CoreFrequency
 	 * and PadFrequency, respectively.
 	 */
-	corepll_frequency = (pad_frequency * core_f) / MLNXBF_I2C_COREPLL_CONST;
+	corepll_frequency = (MLXBF_I2C_PLL_IN_FREQ * core_f) / MLNXBF_I2C_COREPLL_CONST;
 	corepll_frequency /= (++core_r) * (++core_od);
 
 	return corepll_frequency;
@@ -2180,14 +2200,14 @@
 			[1] = &mlxbf_i2c_corepll_res[MLXBF_I2C_CHIP_TYPE_1],
 			[2] = &mlxbf_i2c_gpio_res[MLXBF_I2C_CHIP_TYPE_1]
 		},
-		.calculate_freq = mlxbf_calculate_freq_from_tyu
+		.calculate_freq = mlxbf_i2c_calculate_freq_from_tyu
 	},
 	[MLXBF_I2C_CHIP_TYPE_2] = {
 		.type = MLXBF_I2C_CHIP_TYPE_2,
 		.shared_res = {
 			[0] = &mlxbf_i2c_corepll_res[MLXBF_I2C_CHIP_TYPE_2]
 		},
-		.calculate_freq = mlxbf_calculate_freq_from_yu
+		.calculate_freq = mlxbf_i2c_calculate_freq_from_yu
 	}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mlxcpld.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mlxcpld.c
@@ -49,7 +49,7 @@
 #define MLXCPLD_LPCI2C_NACK_IND		2
 
 #define MLXCPLD_I2C_FREQ_1000KHZ_SET	0x04
-#define MLXCPLD_I2C_FREQ_400KHZ_SET	0x0c
+#define MLXCPLD_I2C_FREQ_400KHZ_SET	0x0e
 #define MLXCPLD_I2C_FREQ_100KHZ_SET	0x42
 
 enum mlxcpld_i2c_frequency {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mpc.c
@@ -119,23 +119,30 @@
 /* Sometimes 9th clock pulse isn't generated, and slave doesn't release
  * the bus, because it wants to send ACK.
  * Following sequence of enabling/disabling and sending start/stop generates
- * the 9 pulses, so it's all OK.
+ * the 9 pulses, each with a START then ending with STOP, so it's all OK.
  */
 static void mpc_i2c_fixup(struct mpc_i2c *i2c)
 {
 	int k;
-	u32 delay_val = 1000000 / i2c->real_clk + 1;
-
-	if (delay_val < 2)
-		delay_val = 2;
+	unsigned long flags;
 
 	for (k = 9; k; k--) {
 		writeccr(i2c, 0);
-		writeccr(i2c, CCR_MSTA | CCR_MTX | CCR_MEN);
+		writeb(0, i2c->base + MPC_I2C_SR); /* clear any status bits */
+		writeccr(i2c, CCR_MEN | CCR_MSTA); /* START */
+		readb(i2c->base + MPC_I2C_DR); /* init xfer */
+		udelay(15); /* let it hit the bus */
+		local_irq_save(flags); /* should not be delayed further */
+		writeccr(i2c, CCR_MEN | CCR_MSTA | CCR_RSTA); /* delay SDA */
 		readb(i2c->base + MPC_I2C_DR);
-		writeccr(i2c, CCR_MEN);
-		udelay(delay_val << 1);
-	}
+		if (k != 1)
+			udelay(5);
+		local_irq_restore(flags);
+	}
+	writeccr(i2c, CCR_MEN); /* Initiate STOP */
+	readb(i2c->base + MPC_I2C_DR);
+	udelay(15); /* Let STOP propagate */
+	writeccr(i2c, 0);
 }
 
 static int i2c_mpc_wait_sr(struct mpc_i2c *i2c, int mask)
@@ -492,7 +499,7 @@
 
 static void mpc_i2c_do_action(struct mpc_i2c *i2c)
 {
-	struct i2c_msg *msg = &i2c->msgs[i2c->curr_msg];
+	struct i2c_msg *msg = NULL;
 	int dir = 0;
 	int recv_len = 0;
 	u8 byte;
@@ -501,10 +508,13 @@
 
 	i2c->cntl_bits &= ~(CCR_RSTA | CCR_MTX | CCR_TXAK);
 
-	if (msg->flags & I2C_M_RD)
-		dir = 1;
-	if (msg->flags & I2C_M_RECV_LEN)
-		recv_len = 1;
+	if (i2c->action != MPC_I2C_ACTION_STOP) {
+		msg = &i2c->msgs[i2c->curr_msg];
+		if (msg->flags & I2C_M_RD)
+			dir = 1;
+		if (msg->flags & I2C_M_RECV_LEN)
+			recv_len = 1;
+	}
 
 	switch (i2c->action) {
 	case MPC_I2C_ACTION_RESTART:
@@ -581,7 +591,7 @@
 		break;
 	}
 
-	if (msg->len == i2c->byte_posn) {
+	if (msg && msg->len == i2c->byte_posn) {
 		i2c->curr_msg++;
 		i2c->byte_posn = 0;
 
@@ -636,7 +646,7 @@
 	status = readb(i2c->base + MPC_I2C_SR);
 	if (status & CSR_MIF) {
 		/* Wait up to 100us for transfer to properly complete */
-		readb_poll_timeout(i2c->base + MPC_I2C_SR, status, !(status & CSR_MCF), 0, 100);
+		readb_poll_timeout_atomic(i2c->base + MPC_I2C_SR, status, status & CSR_MCF, 0, 100);
 		writeb(0, i2c->base + MPC_I2C_SR);
 		mpc_i2c_do_intr(i2c, status);
 		return IRQ_HANDLED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mt65xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mt65xx.c
@@ -195,7 +195,7 @@
 	[OFFSET_CLOCK_DIV] = 0x48,
 	[OFFSET_SOFTRESET] = 0x50,
 	[OFFSET_SCL_MIS_COMP_POINT] = 0x90,
-	[OFFSET_DEBUGSTAT] = 0xe0,
+	[OFFSET_DEBUGSTAT] = 0xe4,
 	[OFFSET_DEBUGCTRL] = 0xe8,
 	[OFFSET_FIFO_STAT] = 0xf4,
 	[OFFSET_FIFO_THRESH] = 0xf8,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mt7621.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mt7621.c
@@ -304,7 +304,8 @@
 
 	if (i2c->bus_freq == 0) {
 		dev_warn(i2c->dev, "clock-frequency 0 not supported\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_disable_clk;
 	}
 
 	adap = &i2c->adap;
@@ -322,10 +323,15 @@
 
 	ret = i2c_add_adapter(adap);
 	if (ret < 0)
-		return ret;
+		goto err_disable_clk;
 
 	dev_info(&pdev->dev, "clock %u kHz\n", i2c->bus_freq / 1000);
 
+	return 0;
+
+err_disable_clk:
+	clk_disable_unprepare(i2c->clk);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mv64xxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mv64xxx.c
@@ -150,6 +150,7 @@
 	/* Clk div is 2 to the power n, not 2 to the power n + 1 */
 	bool			clk_n_base_0;
 	struct i2c_bus_recovery_info	rinfo;
+	bool			atomic;
 };
 
 static struct mv64xxx_i2c_regs mv64xxx_i2c_regs_mv64xxx = {
@@ -179,7 +180,10 @@
 	u32	dir = 0;
 
 	drv_data->cntl_bits = MV64XXX_I2C_REG_CONTROL_ACK |
-		MV64XXX_I2C_REG_CONTROL_INTEN | MV64XXX_I2C_REG_CONTROL_TWSIEN;
+			      MV64XXX_I2C_REG_CONTROL_TWSIEN;
+
+	if (!drv_data->atomic)
+		drv_data->cntl_bits |= MV64XXX_I2C_REG_CONTROL_INTEN;
 
 	if (msg->flags & I2C_M_RD)
 		dir = 1;
@@ -409,7 +413,8 @@
 	case MV64XXX_I2C_ACTION_RCV_DATA_STOP:
 		drv_data->msg->buf[drv_data->byte_posn++] =
 			readl(drv_data->reg_base + drv_data->reg_offsets.data);
-		drv_data->cntl_bits &= ~MV64XXX_I2C_REG_CONTROL_INTEN;
+		if (!drv_data->atomic)
+			drv_data->cntl_bits &= ~MV64XXX_I2C_REG_CONTROL_INTEN;
 		writel(drv_data->cntl_bits | MV64XXX_I2C_REG_CONTROL_STOP,
 			drv_data->reg_base + drv_data->reg_offsets.control);
 		drv_data->block = 0;
@@ -427,7 +432,8 @@
 		drv_data->rc = -EIO;
 		fallthrough;
 	case MV64XXX_I2C_ACTION_SEND_STOP:
-		drv_data->cntl_bits &= ~MV64XXX_I2C_REG_CONTROL_INTEN;
+		if (!drv_data->atomic)
+			drv_data->cntl_bits &= ~MV64XXX_I2C_REG_CONTROL_INTEN;
 		writel(drv_data->cntl_bits | MV64XXX_I2C_REG_CONTROL_STOP,
 			drv_data->reg_base + drv_data->reg_offsets.control);
 		drv_data->block = 0;
@@ -514,6 +520,17 @@
 
 	while (readl(drv_data->reg_base + drv_data->reg_offsets.control) &
 						MV64XXX_I2C_REG_CONTROL_IFLG) {
+		/*
+		 * It seems that sometime the controller updates the status
+		 * register only after it asserts IFLG in control register.
+		 * This may result in weird bugs when in atomic mode. A delay
+		 * of 100 ns before reading the status register solves this
+		 * issue. This bug does not seem to appear when using
+		 * interrupts.
+		 */
+		if (drv_data->atomic)
+			ndelay(100);
+
 		status = readl(drv_data->reg_base + drv_data->reg_offsets.status);
 		mv64xxx_i2c_fsm(drv_data, status);
 		mv64xxx_i2c_do_action(drv_data);
@@ -575,6 +592,17 @@
 		spin_unlock_irqrestore(&drv_data->lock, flags);
 }
 
+static void mv64xxx_i2c_wait_polling(struct mv64xxx_i2c_data *drv_data)
+{
+	ktime_t timeout = ktime_add_ms(ktime_get(), drv_data->adapter.timeout);
+
+	while (READ_ONCE(drv_data->block) &&
+	       ktime_compare(ktime_get(), timeout) < 0) {
+		udelay(5);
+		mv64xxx_i2c_intr(0, drv_data);
+	}
+}
+
 static int
 mv64xxx_i2c_execute_msg(struct mv64xxx_i2c_data *drv_data, struct i2c_msg *msg,
 				int is_last)
@@ -590,7 +618,11 @@
 	mv64xxx_i2c_send_start(drv_data);
 	spin_unlock_irqrestore(&drv_data->lock, flags);
 
-	mv64xxx_i2c_wait_for_completion(drv_data);
+	if (!drv_data->atomic)
+		mv64xxx_i2c_wait_for_completion(drv_data);
+	else
+		mv64xxx_i2c_wait_polling(drv_data);
+
 	return drv_data->rc;
 }
 
@@ -717,7 +749,7 @@
 }
 
 static int
-mv64xxx_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
+mv64xxx_i2c_xfer_core(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 {
 	struct mv64xxx_i2c_data *drv_data = i2c_get_adapdata(adap);
 	int rc, ret = num;
@@ -730,7 +762,7 @@
 	drv_data->msgs = msgs;
 	drv_data->num_msgs = num;
 
-	if (mv64xxx_i2c_can_offload(drv_data))
+	if (mv64xxx_i2c_can_offload(drv_data) && !drv_data->atomic)
 		rc = mv64xxx_i2c_offload_xfer(drv_data);
 	else
 		rc = mv64xxx_i2c_execute_msg(drv_data, &msgs[0], num == 1);
@@ -747,8 +779,27 @@
 	return ret;
 }
 
+static int
+mv64xxx_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
+{
+	struct mv64xxx_i2c_data *drv_data = i2c_get_adapdata(adap);
+
+	drv_data->atomic = 0;
+	return mv64xxx_i2c_xfer_core(adap, msgs, num);
+}
+
+static int mv64xxx_i2c_xfer_atomic(struct i2c_adapter *adap,
+				   struct i2c_msg msgs[], int num)
+{
+	struct mv64xxx_i2c_data *drv_data = i2c_get_adapdata(adap);
+
+	drv_data->atomic = 1;
+	return mv64xxx_i2c_xfer_core(adap, msgs, num);
+}
+
 static const struct i2c_algorithm mv64xxx_i2c_algo = {
 	.master_xfer = mv64xxx_i2c_xfer,
+	.master_xfer_atomic = mv64xxx_i2c_xfer_atomic,
 	.functionality = mv64xxx_i2c_functionality,
 };
 
@@ -1047,14 +1098,6 @@
 	return 0;
 }
 
-static void
-mv64xxx_i2c_shutdown(struct platform_device *pd)
-{
-	pm_runtime_disable(&pd->dev);
-	if (!pm_runtime_status_suspended(&pd->dev))
-		mv64xxx_i2c_runtime_suspend(&pd->dev);
-}
-
 static const struct dev_pm_ops mv64xxx_i2c_pm_ops = {
 	SET_RUNTIME_PM_OPS(mv64xxx_i2c_runtime_suspend,
 			   mv64xxx_i2c_runtime_resume, NULL)
@@ -1065,7 +1108,6 @@
 static struct platform_driver mv64xxx_i2c_driver = {
 	.probe	= mv64xxx_i2c_probe,
 	.remove	= mv64xxx_i2c_remove,
-	.shutdown = mv64xxx_i2c_shutdown,
 	.driver	= {
 		.name	= MV64XXX_I2C_CTLR_NAME,
 		.pm     = &mv64xxx_i2c_pm_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-mxs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-mxs.c
@@ -799,7 +799,7 @@
 	if (!i2c)
 		return -ENOMEM;
 
-	i2c->dev_type = (enum mxs_i2c_devtype)of_device_get_match_data(&pdev->dev);
+	i2c->dev_type = (uintptr_t)of_device_get_match_data(&pdev->dev);
 
 	i2c->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(i2c->regs))
@@ -826,8 +826,8 @@
 	/* Setup the DMA */
 	i2c->dmach = dma_request_chan(dev, "rx-tx");
 	if (IS_ERR(i2c->dmach)) {
-		dev_err(dev, "Failed to request dma\n");
-		return PTR_ERR(i2c->dmach);
+		return dev_err_probe(dev, PTR_ERR(i2c->dmach),
+				     "Failed to request dma\n");
 	}
 
 	platform_set_drvdata(pdev, i2c);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-nomadik.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-nomadik.c
@@ -970,12 +970,10 @@
 	struct i2c_vendor_data *vendor = id->data;
 	u32 max_fifo_threshold = (vendor->fifodepth / 2) - 1;
 
-	dev = devm_kzalloc(&adev->dev, sizeof(struct nmk_i2c_dev), GFP_KERNEL);
-	if (!dev) {
-		dev_err(&adev->dev, "cannot allocate memory\n");
-		ret = -ENOMEM;
-		goto err_no_mem;
-	}
+	dev = devm_kzalloc(&adev->dev, sizeof(*dev), GFP_KERNEL);
+	if (!dev)
+		return -ENOMEM;
+
 	dev->vendor = vendor;
 	dev->adev = adev;
 	nmk_i2c_of_probe(np, dev);
@@ -996,30 +994,21 @@
 
 	dev->virtbase = devm_ioremap(&adev->dev, adev->res.start,
 				resource_size(&adev->res));
-	if (!dev->virtbase) {
-		ret = -ENOMEM;
-		goto err_no_mem;
-	}
+	if (!dev->virtbase)
+		return -ENOMEM;
 
 	dev->irq = adev->irq[0];
 	ret = devm_request_irq(&adev->dev, dev->irq, i2c_irq_handler, 0,
 				DRIVER_NAME, dev);
 	if (ret) {
 		dev_err(&adev->dev, "cannot claim the irq %d\n", dev->irq);
-		goto err_no_mem;
+		return ret;
 	}
 
-	dev->clk = devm_clk_get(&adev->dev, NULL);
+	dev->clk = devm_clk_get_enabled(&adev->dev, NULL);
 	if (IS_ERR(dev->clk)) {
-		dev_err(&adev->dev, "could not get i2c clock\n");
-		ret = PTR_ERR(dev->clk);
-		goto err_no_mem;
-	}
-
-	ret = clk_prepare_enable(dev->clk);
-	if (ret) {
-		dev_err(&adev->dev, "can't prepare_enable clock\n");
-		goto err_no_mem;
+		dev_err(&adev->dev, "could enable i2c clock\n");
+		return PTR_ERR(dev->clk);
 	}
 
 	init_hw(dev);
@@ -1042,22 +1031,15 @@
 
 	ret = i2c_add_adapter(adap);
 	if (ret)
-		goto err_no_adap;
+		return ret;
 
 	pm_runtime_put(&adev->dev);
 
 	return 0;
-
- err_no_adap:
-	clk_disable_unprepare(dev->clk);
- err_no_mem:
-
-	return ret;
 }
 
 static void nmk_i2c_remove(struct amba_device *adev)
 {
-	struct resource *res = &adev->res;
 	struct nmk_i2c_dev *dev = amba_get_drvdata(adev);
 
 	i2c_del_adapter(&dev->adap);
@@ -1066,8 +1048,6 @@
 	clear_all_interrupts(dev);
 	/* disable the controller */
 	i2c_clr_bit(dev->virtbase + I2C_CR, I2C_CR_PE);
-	clk_disable_unprepare(dev->clk);
-	release_mem_region(res->start, resource_size(res));
 }
 
 static struct i2c_vendor_data vendor_stn8815 = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-npcm7xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-npcm7xx.c
@@ -123,11 +123,11 @@
  * Since the addr regs are sprinkled all over the address space,
  * use this array to get the address or each register.
  */
-#define I2C_NUM_OWN_ADDR 10
+#define I2C_NUM_OWN_ADDR 2
+#define I2C_NUM_OWN_ADDR_SUPPORTED 2
+
 static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
-	NPCM_I2CADDR1, NPCM_I2CADDR2, NPCM_I2CADDR3, NPCM_I2CADDR4,
-	NPCM_I2CADDR5, NPCM_I2CADDR6, NPCM_I2CADDR7, NPCM_I2CADDR8,
-	NPCM_I2CADDR9, NPCM_I2CADDR10,
+	NPCM_I2CADDR1, NPCM_I2CADDR2,
 };
 #endif
 
@@ -359,14 +359,14 @@
 {
 	struct npcm_i2c *bus = container_of(_adap, struct npcm_i2c, adap);
 
-	return !!(I2CCTL3_SCL_LVL & ioread32(bus->reg + NPCM_I2CCTL3));
+	return !!(I2CCTL3_SCL_LVL & ioread8(bus->reg + NPCM_I2CCTL3));
 }
 
 static int npcm_i2c_get_SDA(struct i2c_adapter *_adap)
 {
 	struct npcm_i2c *bus = container_of(_adap, struct npcm_i2c, adap);
 
-	return !!(I2CCTL3_SDA_LVL & ioread32(bus->reg + NPCM_I2CCTL3));
+	return !!(I2CCTL3_SDA_LVL & ioread8(bus->reg + NPCM_I2CCTL3));
 }
 
 static inline u16 npcm_i2c_get_index(struct npcm_i2c *bus)
@@ -391,14 +391,10 @@
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	int i;
 
-	/* select bank 0 for I2C addresses */
-	npcm_i2c_select_bank(bus, I2C_BANK_0);
-
 	/* Slave addresses removal */
-	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR; i++)
+	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++)
 		iowrite8(0, bus->reg + npcm_i2caddr[i]);
 
-	npcm_i2c_select_bank(bus, I2C_BANK_1);
 #endif
 	/* Disable module */
 	i2cctl2 = ioread8(bus->reg + NPCM_I2CCTL2);
@@ -563,6 +559,15 @@
 	iowrite8(val, bus->reg + NPCM_I2CCTL1);
 }
 
+static inline void npcm_i2c_clear_master_status(struct npcm_i2c *bus)
+{
+	u8 val;
+
+	/* Clear NEGACK, STASTR and BER bits */
+	val = NPCM_I2CST_BER | NPCM_I2CST_NEGACK | NPCM_I2CST_STASTR;
+	iowrite8(val, bus->reg + NPCM_I2CST);
+}
+
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 static void npcm_i2c_slave_int_enable(struct npcm_i2c *bus, bool enable)
 {
@@ -594,8 +599,7 @@
 			i2cctl1 &= ~NPCM_I2CCTL1_GCMEN;
 		iowrite8(i2cctl1, bus->reg + NPCM_I2CCTL1);
 		return 0;
-	}
-	if (addr_type == I2C_ARP_ADDR) {
+	} else if (addr_type == I2C_ARP_ADDR) {
 		i2cctl3 = ioread8(bus->reg + NPCM_I2CCTL3);
 		if (enable)
 			i2cctl3 |= I2CCTL3_ARPMEN;
@@ -604,16 +608,16 @@
 		iowrite8(i2cctl3, bus->reg + NPCM_I2CCTL3);
 		return 0;
 	}
+	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
+		dev_err(bus->dev, "try to enable more than 2 SA not supported\n");
+
 	if (addr_type >= I2C_ARP_ADDR)
 		return -EFAULT;
-	/* select bank 0 for address 3 to 10 */
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_0);
+
 	/* Set and enable the address */
 	iowrite8(sa_reg, bus->reg + npcm_i2caddr[addr_type]);
 	npcm_i2c_slave_int_enable(bus, enable);
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_1);
+
 	return 0;
 }
 #endif
@@ -642,8 +646,8 @@
 	iowrite8(NPCM_I2CCST_BB, bus->reg + NPCM_I2CCST);
 	iowrite8(0xFF, bus->reg + NPCM_I2CST);
 
-	/* Clear EOB bit */
-	iowrite8(NPCM_I2CCST3_EO_BUSY, bus->reg + NPCM_I2CCST3);
+	/* Clear and disable EOB */
+	npcm_i2c_eob_int(bus, false);
 
 	/* Clear all fifo bits: */
 	iowrite8(NPCM_I2CFIF_CTS_CLR_FIFO, bus->reg + NPCM_I2CFIF_CTS);
@@ -655,6 +659,9 @@
 	}
 #endif
 
+	/* clear status bits for spurious interrupts */
+	npcm_i2c_clear_master_status(bus);
+
 	bus->state = I2C_IDLE;
 }
 
@@ -668,6 +675,7 @@
 {
 	struct i2c_msg *msgs;
 	int msgs_num;
+	bool do_complete = false;
 
 	msgs = bus->msgs;
 	msgs_num = bus->msgs_num;
@@ -694,23 +702,17 @@
 				 msgs[1].flags & I2C_M_RD)
 				msgs[1].len = info;
 		}
-		if (completion_done(&bus->cmd_complete) == false)
-			complete(&bus->cmd_complete);
-	break;
-
+		do_complete = true;
+		break;
 	case I2C_NACK_IND:
 		/* MASTER transmit got a NACK before tx all bytes */
 		bus->cmd_err = -ENXIO;
-		if (bus->master_or_slave == I2C_MASTER)
-			complete(&bus->cmd_complete);
-
+		do_complete = true;
 		break;
 	case I2C_BUS_ERR_IND:
 		/* Bus error */
 		bus->cmd_err = -EAGAIN;
-		if (bus->master_or_slave == I2C_MASTER)
-			complete(&bus->cmd_complete);
-
+		do_complete = true;
 		break;
 	case I2C_WAKE_UP_IND:
 		/* I2C wake up */
@@ -724,6 +726,8 @@
 	if (bus->slave)
 		bus->master_or_slave = I2C_SLAVE;
 #endif
+	if (do_complete)
+		complete(&bus->cmd_complete);
 }
 
 static u8 npcm_i2c_fifo_usage(struct npcm_i2c *bus)
@@ -815,15 +819,6 @@
 	}
 }
 
-static inline void npcm_i2c_clear_master_status(struct npcm_i2c *bus)
-{
-	u8 val;
-
-	/* Clear NEGACK, STASTR and BER bits */
-	val = NPCM_I2CST_BER | NPCM_I2CST_NEGACK | NPCM_I2CST_STASTR;
-	iowrite8(val, bus->reg + NPCM_I2CST);
-}
-
 static void npcm_i2c_master_abort(struct npcm_i2c *bus)
 {
 	/* Only current master is allowed to issue a stop condition */
@@ -840,15 +835,11 @@
 {
 	u8 slave_add;
 
-	/* select bank 0 for address 3 to 10 */
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_0);
+	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
+		dev_err(bus->dev, "get slave: try to use more than 2 SA not supported\n");
 
 	slave_add = ioread8(bus->reg + npcm_i2caddr[(int)addr_type]);
 
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_1);
-
 	return slave_add;
 }
 
@@ -858,12 +849,12 @@
 
 	/* Set the enable bit */
 	slave_add |= 0x80;
-	npcm_i2c_select_bank(bus, I2C_BANK_0);
-	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR; i++) {
+
+	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++) {
 		if (ioread8(bus->reg + npcm_i2caddr[i]) == slave_add)
 			iowrite8(0, bus->reg + npcm_i2caddr[i]);
 	}
-	npcm_i2c_select_bank(bus, I2C_BANK_1);
+
 	return 0;
 }
 
@@ -918,11 +909,15 @@
 	for (i = 0; i < I2C_HW_FIFO_SIZE; i++) {
 		if (bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
 			break;
-		i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+		if (bus->state == I2C_SLAVE_MATCH) {
+			i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+			bus->state = I2C_OPER_STARTED;
+		} else {
+			i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
+		}
 		ind = (bus->slv_wr_ind + bus->slv_wr_size) % I2C_HW_FIFO_SIZE;
 		bus->slv_wr_buf[ind] = value;
 		bus->slv_wr_size++;
-		i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
 	}
 	return I2C_HW_FIFO_SIZE - ret;
 }
@@ -970,7 +965,6 @@
 	if (nwrite == 0)
 		return;
 
-	bus->state = I2C_OPER_STARTED;
 	bus->operation = I2C_WRITE_OPER;
 
 	/* get the next buffer */
@@ -1231,7 +1225,16 @@
 		ret = IRQ_HANDLED;
 	} /* SDAST */
 
-	return ret;
+	/*
+	 * if irq is not one of the above, make sure EOB is disabled and all
+	 * status bits are cleared.
+	 */
+	if (ret == IRQ_NONE) {
+		npcm_i2c_eob_int(bus, false);
+		npcm_i2c_clear_master_status(bus);
+	}
+
+	return IRQ_HANDLED;
 }
 
 static int npcm_i2c_reg_slave(struct i2c_client *client)
@@ -1467,6 +1470,9 @@
 		npcm_i2c_eob_int(bus, false);
 		npcm_i2c_master_stop(bus);
 
+		/* Clear SDA Status bit (by reading dummy byte) */
+		npcm_i2c_rd_byte(bus);
+
 		/*
 		 * The bus is released from stall only after the SW clears
 		 * NEGACK bit. Then a Stop condition is sent.
@@ -1474,6 +1480,8 @@
 		npcm_i2c_clear_master_status(bus);
 		readx_poll_timeout_atomic(ioread8, bus->reg + NPCM_I2CCST, val,
 					  !(val & NPCM_I2CCST_BUSY), 10, 200);
+		/* verify no status bits are still set after bus is released */
+		npcm_i2c_clear_master_status(bus);
 	}
 	bus->state = I2C_IDLE;
 
@@ -1672,10 +1680,10 @@
 	int              iter = 27;
 
 	if ((npcm_i2c_get_SDA(_adap) == 1) && (npcm_i2c_get_SCL(_adap) == 1)) {
-		dev_dbg(bus->dev, "bus%d recovery skipped, bus not stuck",
-			bus->num);
+		dev_dbg(bus->dev, "bus%d-0x%x recovery skipped, bus not stuck",
+			bus->num, bus->dest_addr);
 		npcm_i2c_reset(bus);
-		return status;
+		return 0;
 	}
 
 	npcm_i2c_int_enable(bus, false);
@@ -1909,6 +1917,7 @@
 	    bus_freq_hz < I2C_FREQ_MIN_HZ || bus_freq_hz > I2C_FREQ_MAX_HZ)
 		return -EINVAL;
 
+	npcm_i2c_int_enable(bus, false);
 	npcm_i2c_disable(bus);
 
 	/* Configure FIFO mode : */
@@ -1937,10 +1946,17 @@
 	val = (val | NPCM_I2CCTL1_NMINTE) & ~NPCM_I2CCTL1_RWS;
 	iowrite8(val, bus->reg + NPCM_I2CCTL1);
 
-	npcm_i2c_int_enable(bus, true);
-
 	npcm_i2c_reset(bus);
 
+	/* check HW is OK: SDA and SCL should be high at this point. */
+	if ((npcm_i2c_get_SDA(&bus->adap) == 0) || (npcm_i2c_get_SCL(&bus->adap) == 0)) {
+		dev_err(bus->dev, "I2C%d init fail: lines are low\n", bus->num);
+		dev_err(bus->dev, "SDA=%d SCL=%d\n", npcm_i2c_get_SDA(&bus->adap),
+			npcm_i2c_get_SCL(&bus->adap));
+		return -ENXIO;
+	}
+
+	npcm_i2c_int_enable(bus, true);
 	return 0;
 }
 
@@ -1988,10 +2004,14 @@
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	if (bus->slave) {
 		bus->master_or_slave = I2C_SLAVE;
-		return npcm_i2c_int_slave_handler(bus);
+		if (npcm_i2c_int_slave_handler(bus))
+			return IRQ_HANDLED;
 	}
 #endif
-	return IRQ_NONE;
+	/* clear status bits for spurious interrupts */
+	npcm_i2c_clear_master_status(bus);
+
+	return IRQ_HANDLED;
 }
 
 static bool npcm_i2c_master_start_xmit(struct npcm_i2c *bus,
@@ -2047,8 +2067,7 @@
 	u16 nwrite, nread;
 	u8 *write_data, *read_data;
 	u8 slave_addr;
-	int timeout;
-	int ret = 0;
+	unsigned long timeout;
 	bool read_block = false;
 	bool read_PEC = false;
 	u8 bus_busy;
@@ -2099,13 +2118,13 @@
 	 * 9: bits per transaction (including the ack/nack)
 	 */
 	timeout_usec = (2 * 9 * USEC_PER_SEC / bus->bus_freq) * (2 + nread + nwrite);
-	timeout = max(msecs_to_jiffies(35), usecs_to_jiffies(timeout_usec));
+	timeout = max_t(unsigned long, bus->adap.timeout, usecs_to_jiffies(timeout_usec));
 	if (nwrite >= 32 * 1024 || nread >= 32 * 1024) {
 		dev_err(bus->dev, "i2c%d buffer too big\n", bus->num);
 		return -EINVAL;
 	}
 
-	time_left = jiffies + msecs_to_jiffies(DEFAULT_STALL_COUNT) + 1;
+	time_left = jiffies + timeout + 1;
 	do {
 		/*
 		 * we must clear slave address immediately when the bus is not
@@ -2138,12 +2157,12 @@
 	bus->read_block_use = read_block;
 
 	reinit_completion(&bus->cmd_complete);
-	if (!npcm_i2c_master_start_xmit(bus, slave_addr, nwrite, nread,
-					write_data, read_data, read_PEC,
-					read_block))
-		ret = -EBUSY;
 
-	if (ret != -EBUSY) {
+	npcm_i2c_int_enable(bus, true);
+
+	if (npcm_i2c_master_start_xmit(bus, slave_addr, nwrite, nread,
+				       write_data, read_data, read_PEC,
+				       read_block)) {
 		time_left = wait_for_completion_timeout(&bus->cmd_complete,
 							timeout);
 
@@ -2157,26 +2176,31 @@
 			}
 		}
 	}
-	ret = bus->cmd_err;
 
 	/* if there was BER, check if need to recover the bus: */
 	if (bus->cmd_err == -EAGAIN)
-		ret = i2c_recover_bus(adap);
+		bus->cmd_err = i2c_recover_bus(adap);
 
 	/*
 	 * After any type of error, check if LAST bit is still set,
 	 * due to a HW issue.
 	 * It cannot be cleared without resetting the module.
 	 */
-	if (bus->cmd_err &&
-	    (NPCM_I2CRXF_CTL_LAST_PEC & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
+	else if (bus->cmd_err &&
+		 (NPCM_I2CRXF_CTL_LAST_PEC & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
 		npcm_i2c_reset(bus);
 
+	/* after any xfer, successful or not, stall and EOB must be disabled */
+	npcm_i2c_stall_after_start(bus, false);
+	npcm_i2c_eob_int(bus, false);
+
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	/* reenable slave if it was enabled */
 	if (bus->slave)
 		iowrite8((bus->slave->addr & 0x7F) | NPCM_I2CADDR_SAEN,
 			 bus->reg + NPCM_I2CADDR1);
+#else
+	npcm_i2c_int_enable(bus, false);
 #endif
 	return bus->cmd_err;
 }
@@ -2269,7 +2293,7 @@
 	adap = &bus->adap;
 	adap->owner = THIS_MODULE;
 	adap->retries = 3;
-	adap->timeout = HZ;
+	adap->timeout = msecs_to_jiffies(35);
 	adap->algo = &npcm_i2c_algo;
 	adap->quirks = &npcm_i2c_quirks;
 	adap->algo_data = bus;
@@ -2281,6 +2305,13 @@
 	if (irq < 0)
 		return irq;
 
+	/*
+	 * Disable the interrupt to avoid the interrupt handler being triggered
+	 * incorrectly by the asynchronous interrupt status since the machine
+	 * might do a warm reset during the last smbus/i2c transfer session.
+	 */
+	npcm_i2c_int_enable(bus, false);
+
 	ret = devm_request_irq(bus->dev, irq, npcm_i2c_bus_irq, 0,
 			       dev_name(bus->dev), bus);
 	if (ret)
@@ -2335,8 +2366,16 @@
 
 static int __init npcm_i2c_init(void)
 {
+	int ret;
+
 	npcm_i2c_debugfs_dir = debugfs_create_dir("npcm_i2c", NULL);
-	platform_driver_register(&npcm_i2c_bus_driver);
+
+	ret = platform_driver_register(&npcm_i2c_bus_driver);
+	if (ret) {
+		debugfs_remove_recursive(npcm_i2c_debugfs_dir);
+		return ret;
+	}
+
 	return 0;
 }
 module_init(npcm_i2c_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-ocores.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-ocores.c
@@ -342,18 +342,18 @@
  * ocores_isr(), we just add our polling code around it.
  *
  * It can run in atomic context
+ *
+ * Return: 0 on success, -ETIMEDOUT on timeout
  */
-static void ocores_process_polling(struct ocores_i2c *i2c)
+static int ocores_process_polling(struct ocores_i2c *i2c)
 {
-	while (1) {
-		irqreturn_t ret;
-		int err;
+	irqreturn_t ret;
+	int err = 0;
 
+	while (1) {
 		err = ocores_poll_wait(i2c);
-		if (err) {
-			i2c->state = STATE_ERROR;
+		if (err)
 			break; /* timeout */
-		}
 
 		ret = ocores_isr(-1, i2c);
 		if (ret == IRQ_NONE)
@@ -364,13 +364,15 @@
 					break;
 		}
 	}
+
+	return err;
 }
 
 static int ocores_xfer_core(struct ocores_i2c *i2c,
 			    struct i2c_msg *msgs, int num,
 			    bool polling)
 {
-	int ret;
+	int ret = 0;
 	u8 ctrl;
 
 	ctrl = oc_getreg(i2c, OCI2C_CONTROL);
@@ -388,15 +390,16 @@
 	oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_START);
 
 	if (polling) {
-		ocores_process_polling(i2c);
+		ret = ocores_process_polling(i2c);
 	} else {
-		ret = wait_event_timeout(i2c->wait,
-					 (i2c->state == STATE_ERROR) ||
-					 (i2c->state == STATE_DONE), HZ);
-		if (ret == 0) {
-			ocores_process_timeout(i2c);
-			return -ETIMEDOUT;
-		}
+		if (wait_event_timeout(i2c->wait,
+				       (i2c->state == STATE_ERROR) ||
+				       (i2c->state == STATE_DONE), HZ) == 0)
+			ret = -ETIMEDOUT;
+	}
+	if (ret) {
+		ocores_process_timeout(i2c);
+		return ret;
 	}
 
 	return (i2c->state == STATE_DONE) ? num : -EIO;
@@ -439,8 +442,8 @@
 	oc_setreg(i2c, OCI2C_PREHIGH, prescale >> 8);
 
 	/* Init the device */
-	oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_IACK);
 	oc_setreg(i2c, OCI2C_CONTROL, ctrl | OCI2C_CTRL_EN);
+	oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_IACK);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-omap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-omap.c
@@ -1049,23 +1049,6 @@
 	return 0;
 }
 
-static irqreturn_t
-omap_i2c_isr(int irq, void *dev_id)
-{
-	struct omap_i2c_dev *omap = dev_id;
-	irqreturn_t ret = IRQ_HANDLED;
-	u16 mask;
-	u16 stat;
-
-	stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
-	mask = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG);
-
-	if (stat & mask)
-		ret = IRQ_WAKE_THREAD;
-
-	return ret;
-}
-
 static int omap_i2c_xfer_data(struct omap_i2c_dev *omap)
 {
 	u16 bits;
@@ -1096,8 +1079,13 @@
 		}
 
 		if (stat & OMAP_I2C_STAT_NACK) {
-			err |= OMAP_I2C_STAT_NACK;
+			omap->cmd_err |= OMAP_I2C_STAT_NACK;
 			omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK);
+
+			if (!(stat & ~OMAP_I2C_STAT_NACK)) {
+				err = -EAGAIN;
+				break;
+			}
 		}
 
 		if (stat & OMAP_I2C_STAT_AL) {
@@ -1475,7 +1463,7 @@
 				IRQF_NO_SUSPEND, pdev->name, omap);
 	else
 		r = devm_request_threaded_irq(&pdev->dev, omap->irq,
-				omap_i2c_isr, omap_i2c_isr_thread,
+				NULL, omap_i2c_isr_thread,
 				IRQF_NO_SUSPEND | IRQF_ONESHOT,
 				pdev->name, omap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-pasemi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-pasemi.c
@@ -137,6 +137,12 @@
 
 		TXFIFO_WR(smbus, msg->buf[msg->len-1] |
 			  (stop ? MTXFIFO_STOP : 0));
+
+		if (stop) {
+			err = pasemi_smb_waitready(smbus);
+			if (err)
+				goto reset_out;
+		}
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-piix4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-piix4.c
@@ -77,6 +77,7 @@
 
 /* SB800 constants */
 #define SB800_PIIX4_SMB_IDX		0xcd6
+#define SB800_PIIX4_SMB_MAP_SIZE	2
 
 #define KERNCZ_IMC_IDX			0x3e
 #define KERNCZ_IMC_DATA			0x3f
@@ -97,6 +98,9 @@
 #define SB800_PIIX4_PORT_IDX_MASK_KERNCZ	0x18
 #define SB800_PIIX4_PORT_IDX_SHIFT_KERNCZ	3
 
+#define SB800_PIIX4_FCH_PM_ADDR			0xFED80300
+#define SB800_PIIX4_FCH_PM_SIZE			8
+
 /* insmod parameters */
 
 /* If force is set to anything different from 0, we forcibly enable the
@@ -155,6 +159,11 @@
 };
 static const char *piix4_aux_port_name_sb800 = " port 1";
 
+struct sb800_mmio_cfg {
+	void __iomem *addr;
+	bool use_mmio;
+};
+
 struct i2c_piix4_adapdata {
 	unsigned short smba;
 
@@ -162,8 +171,74 @@
 	bool sb800_main;
 	bool notify_imc;
 	u8 port;		/* Port number, shifted */
+	struct sb800_mmio_cfg mmio_cfg;
 };
 
+static int piix4_sb800_region_request(struct device *dev,
+				      struct sb800_mmio_cfg *mmio_cfg)
+{
+	if (mmio_cfg->use_mmio) {
+		void __iomem *addr;
+
+		if (!request_mem_region_muxed(SB800_PIIX4_FCH_PM_ADDR,
+					      SB800_PIIX4_FCH_PM_SIZE,
+					      "sb800_piix4_smb")) {
+			dev_err(dev,
+				"SMBus base address memory region 0x%x already in use.\n",
+				SB800_PIIX4_FCH_PM_ADDR);
+			return -EBUSY;
+		}
+
+		addr = ioremap(SB800_PIIX4_FCH_PM_ADDR,
+			       SB800_PIIX4_FCH_PM_SIZE);
+		if (!addr) {
+			release_mem_region(SB800_PIIX4_FCH_PM_ADDR,
+					   SB800_PIIX4_FCH_PM_SIZE);
+			dev_err(dev, "SMBus base address mapping failed.\n");
+			return -ENOMEM;
+		}
+
+		mmio_cfg->addr = addr;
+
+		return 0;
+	}
+
+	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
+				  "sb800_piix4_smb")) {
+		dev_err(dev,
+			"SMBus base address index region 0x%x already in use.\n",
+			SB800_PIIX4_SMB_IDX);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void piix4_sb800_region_release(struct device *dev,
+				       struct sb800_mmio_cfg *mmio_cfg)
+{
+	if (mmio_cfg->use_mmio) {
+		iounmap(mmio_cfg->addr);
+		release_mem_region(SB800_PIIX4_FCH_PM_ADDR,
+				   SB800_PIIX4_FCH_PM_SIZE);
+		return;
+	}
+
+	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+}
+
+static bool piix4_sb800_use_mmio(struct pci_dev *PIIX4_dev)
+{
+	/*
+	 * cd6h/cd7h port I/O accesses can be disabled on AMD processors
+	 * w/ SMBus PCI revision ID 0x51 or greater. MMIO is supported on
+	 * the same processors and is the recommended access method.
+	 */
+	return (PIIX4_dev->vendor == PCI_VENDOR_ID_AMD &&
+		PIIX4_dev->device == PCI_DEVICE_ID_AMD_KERNCZ_SMBUS &&
+		PIIX4_dev->revision >= 0x51);
+}
+
 static int piix4_setup(struct pci_dev *PIIX4_dev,
 		       const struct pci_device_id *id)
 {
@@ -263,12 +338,61 @@
 	return piix4_smba;
 }
 
+static int piix4_setup_sb800_smba(struct pci_dev *PIIX4_dev,
+				  u8 smb_en,
+				  u8 aux,
+				  u8 *smb_en_status,
+				  unsigned short *piix4_smba)
+{
+	struct sb800_mmio_cfg mmio_cfg;
+	u8 smba_en_lo;
+	u8 smba_en_hi;
+	int retval;
+
+	mmio_cfg.use_mmio = piix4_sb800_use_mmio(PIIX4_dev);
+	retval = piix4_sb800_region_request(&PIIX4_dev->dev, &mmio_cfg);
+	if (retval)
+		return retval;
+
+	if (mmio_cfg.use_mmio) {
+		smba_en_lo = ioread8(mmio_cfg.addr);
+		smba_en_hi = ioread8(mmio_cfg.addr + 1);
+	} else {
+		outb_p(smb_en, SB800_PIIX4_SMB_IDX);
+		smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
+		outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
+		smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
+	}
+
+	piix4_sb800_region_release(&PIIX4_dev->dev, &mmio_cfg);
+
+	if (!smb_en) {
+		*smb_en_status = smba_en_lo & 0x10;
+		*piix4_smba = smba_en_hi << 8;
+		if (aux)
+			*piix4_smba |= 0x20;
+	} else {
+		*smb_en_status = smba_en_lo & 0x01;
+		*piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
+	}
+
+	if (!*smb_en_status) {
+		dev_err(&PIIX4_dev->dev,
+			"SMBus Host Controller not enabled!\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
 static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			     const struct pci_device_id *id, u8 aux)
 {
 	unsigned short piix4_smba;
-	u8 smba_en_lo, smba_en_hi, smb_en, smb_en_status, port_sel;
+	u8 smb_en, smb_en_status, port_sel;
 	u8 i2ccfg, i2ccfg_offset = 0x10;
+	struct sb800_mmio_cfg mmio_cfg;
+	int retval;
 
 	/* SB800 and later SMBus does not support forcing address */
 	if (force || force_addr) {
@@ -290,35 +414,11 @@
 	else
 		smb_en = (aux) ? 0x28 : 0x2c;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, 2, "sb800_piix4_smb")) {
-		dev_err(&PIIX4_dev->dev,
-			"SMB base address index region 0x%x already in use.\n",
-			SB800_PIIX4_SMB_IDX);
-		return -EBUSY;
-	}
-
-	outb_p(smb_en, SB800_PIIX4_SMB_IDX);
-	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
-	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
-	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
-
-	release_region(SB800_PIIX4_SMB_IDX, 2);
+	retval = piix4_setup_sb800_smba(PIIX4_dev, smb_en, aux, &smb_en_status,
+					&piix4_smba);
 
-	if (!smb_en) {
-		smb_en_status = smba_en_lo & 0x10;
-		piix4_smba = smba_en_hi << 8;
-		if (aux)
-			piix4_smba |= 0x20;
-	} else {
-		smb_en_status = smba_en_lo & 0x01;
-		piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
-	}
-
-	if (!smb_en_status) {
-		dev_err(&PIIX4_dev->dev,
-			"SMBus Host Controller not enabled!\n");
-		return -ENODEV;
-	}
+	if (retval)
+		return retval;
 
 	if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
 		return -ENODEV;
@@ -371,10 +471,11 @@
 			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		}
 	} else {
-		if (!request_muxed_region(SB800_PIIX4_SMB_IDX, 2,
-					  "sb800_piix4_smb")) {
+		mmio_cfg.use_mmio = piix4_sb800_use_mmio(PIIX4_dev);
+		retval = piix4_sb800_region_request(&PIIX4_dev->dev, &mmio_cfg);
+		if (retval) {
 			release_region(piix4_smba, SMBIOSIZE);
-			return -EBUSY;
+			return retval;
 		}
 
 		outb_p(SB800_PIIX4_PORT_IDX_SEL, SB800_PIIX4_SMB_IDX);
@@ -384,7 +485,7 @@
 				       SB800_PIIX4_PORT_IDX;
 		piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
 		piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
-		release_region(SB800_PIIX4_SMB_IDX, 2);
+		piix4_sb800_region_release(&PIIX4_dev->dev, &mmio_cfg);
 	}
 
 	dev_info(&PIIX4_dev->dev,
@@ -662,6 +763,29 @@
 	release_region(KERNCZ_IMC_IDX, 2);
 }
 
+static int piix4_sb800_port_sel(u8 port, struct sb800_mmio_cfg *mmio_cfg)
+{
+	u8 smba_en_lo, val;
+
+	if (mmio_cfg->use_mmio) {
+		smba_en_lo = ioread8(mmio_cfg->addr + piix4_port_sel_sb800);
+		val = (smba_en_lo & ~piix4_port_mask_sb800) | port;
+		if (smba_en_lo != val)
+			iowrite8(val, mmio_cfg->addr + piix4_port_sel_sb800);
+
+		return (smba_en_lo & piix4_port_mask_sb800);
+	}
+
+	outb_p(piix4_port_sel_sb800, SB800_PIIX4_SMB_IDX);
+	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
+
+	val = (smba_en_lo & ~piix4_port_mask_sb800) | port;
+	if (smba_en_lo != val)
+		outb_p(val, SB800_PIIX4_SMB_IDX + 1);
+
+	return (smba_en_lo & piix4_port_mask_sb800);
+}
+
 /*
  * Handles access to multiple SMBus ports on the SB800.
  * The port is selected by bits 2:1 of the smb_en register (0x2c).
@@ -678,12 +802,12 @@
 	unsigned short piix4_smba = adapdata->smba;
 	int retries = MAX_TIMEOUT;
 	int smbslvcnt;
-	u8 smba_en_lo;
-	u8 port;
+	u8 prev_port;
 	int retval;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, 2, "sb800_piix4_smb"))
-		return -EBUSY;
+	retval = piix4_sb800_region_request(&adap->dev, &adapdata->mmio_cfg);
+	if (retval)
+		return retval;
 
 	/* Request the SMBUS semaphore, avoid conflicts with the IMC */
 	smbslvcnt  = inb_p(SMBSLVCNT);
@@ -738,18 +862,12 @@
 		}
 	}
 
-	outb_p(piix4_port_sel_sb800, SB800_PIIX4_SMB_IDX);
-	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
-
-	port = adapdata->port;
-	if ((smba_en_lo & piix4_port_mask_sb800) != port)
-		outb_p((smba_en_lo & ~piix4_port_mask_sb800) | port,
-		       SB800_PIIX4_SMB_IDX + 1);
+	prev_port = piix4_sb800_port_sel(adapdata->port, &adapdata->mmio_cfg);
 
 	retval = piix4_access(adap, addr, flags, read_write,
 			      command, size, data);
 
-	outb_p(smba_en_lo, SB800_PIIX4_SMB_IDX + 1);
+	piix4_sb800_port_sel(prev_port, &adapdata->mmio_cfg);
 
 	/* Release the semaphore */
 	outb_p(smbslvcnt | 0x20, SMBSLVCNT);
@@ -758,7 +876,7 @@
 		piix4_imc_wakeup();
 
 release:
-	release_region(SB800_PIIX4_SMB_IDX, 2);
+	piix4_sb800_region_release(&adap->dev, &adapdata->mmio_cfg);
 	return retval;
 }
 
@@ -836,6 +954,7 @@
 		return -ENOMEM;
 	}
 
+	adapdata->mmio_cfg.use_mmio = piix4_sb800_use_mmio(dev);
 	adapdata->smba = smba;
 	adapdata->sb800_main = sb800_main;
 	adapdata->port = port << piix4_port_shift_sb800;
@@ -961,6 +1080,7 @@
 					   "", &piix4_main_adapters[0]);
 		if (retval < 0)
 			return retval;
+		piix4_adapter_count = 1;
 	}
 
 	/* Check for auxiliary SMBus on some AMD chipsets */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-pnx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-pnx.c
@@ -15,7 +15,6 @@
 #include <linux/ioport.h>
 #include <linux/delay.h>
 #include <linux/i2c.h>
-#include <linux/timer.h>
 #include <linux/completion.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
@@ -32,7 +31,6 @@
 	int			ret;		/* Return value */
 	int			mode;		/* Interface mode */
 	struct completion	complete;	/* I/O completion */
-	struct timer_list	timer;		/* Timeout */
 	u8 *			buf;		/* Data buffer */
 	int			len;		/* Length of data buffer */
 	int			order;		/* RX Bytes to order via TX */
@@ -97,7 +95,7 @@
 
 static inline int wait_timeout(struct i2c_pnx_algo_data *data)
 {
-	long timeout = data->timeout;
+	long timeout = jiffies_to_msecs(data->timeout);
 	while (timeout > 0 &&
 			(ioread32(I2C_REG_STS(data)) & mstatus_active)) {
 		mdelay(1);
@@ -108,7 +106,7 @@
 
 static inline int wait_reset(struct i2c_pnx_algo_data *data)
 {
-	long timeout = data->timeout;
+	long timeout = jiffies_to_msecs(data->timeout);
 	while (timeout > 0 &&
 			(ioread32(I2C_REG_CTL(data)) & mcntrl_reset)) {
 		mdelay(1);
@@ -117,24 +115,6 @@
 	return (timeout <= 0);
 }
 
-static inline void i2c_pnx_arm_timer(struct i2c_pnx_algo_data *alg_data)
-{
-	struct timer_list *timer = &alg_data->mif.timer;
-	unsigned long expires = msecs_to_jiffies(alg_data->timeout);
-
-	if (expires <= 1)
-		expires = 2;
-
-	del_timer_sync(timer);
-
-	dev_dbg(&alg_data->adapter.dev, "Timer armed at %lu plus %lu jiffies.\n",
-		jiffies, expires);
-
-	timer->expires = jiffies + expires;
-
-	add_timer(timer);
-}
-
 /**
  * i2c_pnx_start - start a device
  * @slave_addr:		slave address
@@ -259,8 +239,6 @@
 				~(mcntrl_afie | mcntrl_naie | mcntrl_drmie),
 				  I2C_REG_CTL(alg_data));
 
-			del_timer_sync(&alg_data->mif.timer);
-
 			dev_dbg(&alg_data->adapter.dev,
 				"%s(): Waking up xfer routine.\n",
 				__func__);
@@ -276,8 +254,6 @@
 			~(mcntrl_afie | mcntrl_naie | mcntrl_drmie),
 			  I2C_REG_CTL(alg_data));
 
-		/* Stop timer. */
-		del_timer_sync(&alg_data->mif.timer);
 		dev_dbg(&alg_data->adapter.dev,
 			"%s(): Waking up xfer routine after zero-xfer.\n",
 			__func__);
@@ -364,8 +340,6 @@
 				 mcntrl_drmie | mcntrl_daie);
 			iowrite32(ctl, I2C_REG_CTL(alg_data));
 
-			/* Kill timer. */
-			del_timer_sync(&alg_data->mif.timer);
 			complete(&alg_data->mif.complete);
 		}
 	}
@@ -400,8 +374,6 @@
 			 mcntrl_drmie);
 		iowrite32(ctl, I2C_REG_CTL(alg_data));
 
-		/* Stop timer, to prevent timeout. */
-		del_timer_sync(&alg_data->mif.timer);
 		complete(&alg_data->mif.complete);
 	} else if (stat & mstatus_nai) {
 		/* Slave did not acknowledge, generate a STOP */
@@ -419,8 +391,6 @@
 		/* Our return value. */
 		alg_data->mif.ret = -EIO;
 
-		/* Stop timer, to prevent timeout. */
-		del_timer_sync(&alg_data->mif.timer);
 		complete(&alg_data->mif.complete);
 	} else {
 		/*
@@ -453,9 +423,8 @@
 	return IRQ_HANDLED;
 }
 
-static void i2c_pnx_timeout(struct timer_list *t)
+static void i2c_pnx_timeout(struct i2c_pnx_algo_data *alg_data)
 {
-	struct i2c_pnx_algo_data *alg_data = from_timer(alg_data, t, mif.timer);
 	u32 ctl;
 
 	dev_err(&alg_data->adapter.dev,
@@ -472,7 +441,6 @@
 	iowrite32(ctl, I2C_REG_CTL(alg_data));
 	wait_reset(alg_data);
 	alg_data->mif.ret = -EIO;
-	complete(&alg_data->mif.complete);
 }
 
 static inline void bus_reset_if_active(struct i2c_pnx_algo_data *alg_data)
@@ -514,6 +482,7 @@
 	struct i2c_msg *pmsg;
 	int rc = 0, completed = 0, i;
 	struct i2c_pnx_algo_data *alg_data = adap->algo_data;
+	unsigned long time_left;
 	u32 stat;
 
 	dev_dbg(&alg_data->adapter.dev,
@@ -548,7 +517,6 @@
 		dev_dbg(&alg_data->adapter.dev, "%s(): mode %d, %d bytes\n",
 			__func__, alg_data->mif.mode, alg_data->mif.len);
 
-		i2c_pnx_arm_timer(alg_data);
 
 		/* initialize the completion var */
 		init_completion(&alg_data->mif.complete);
@@ -564,7 +532,10 @@
 			break;
 
 		/* Wait for completion */
-		wait_for_completion(&alg_data->mif.complete);
+		time_left = wait_for_completion_timeout(&alg_data->mif.complete,
+							alg_data->timeout);
+		if (time_left == 0)
+			i2c_pnx_timeout(alg_data);
 
 		if (!(rc = alg_data->mif.ret))
 			completed++;
@@ -657,7 +628,10 @@
 	alg_data->adapter.algo_data = alg_data;
 	alg_data->adapter.nr = pdev->id;
 
-	alg_data->timeout = I2C_PNX_TIMEOUT_DEFAULT;
+	alg_data->timeout = msecs_to_jiffies(I2C_PNX_TIMEOUT_DEFAULT);
+	if (alg_data->timeout <= 1)
+		alg_data->timeout = 2;
+
 #ifdef CONFIG_OF
 	alg_data->adapter.dev.of_node = of_node_get(pdev->dev.of_node);
 	if (pdev->dev.of_node) {
@@ -677,8 +651,6 @@
 	if (IS_ERR(alg_data->clk))
 		return PTR_ERR(alg_data->clk);
 
-	timer_setup(&alg_data->mif.timer, i2c_pnx_timeout, 0);
-
 	snprintf(alg_data->adapter.name, sizeof(alg_data->adapter.name),
 		 "%s", pdev->name);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-pxa-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-pxa-pci.c
@@ -105,7 +105,7 @@
 	int i;
 	struct ce4100_devices *sds;
 
-	ret = pci_enable_device_mem(dev);
+	ret = pcim_enable_device(dev);
 	if (ret)
 		return ret;
 
@@ -114,10 +114,8 @@
 		return -EINVAL;
 	}
 	sds = kzalloc(sizeof(*sds), GFP_KERNEL);
-	if (!sds) {
-		ret = -ENOMEM;
-		goto err_mem;
-	}
+	if (!sds)
+		return -ENOMEM;
 
 	for (i = 0; i < ARRAY_SIZE(sds->pdev); i++) {
 		sds->pdev[i] = add_i2c_device(dev, i);
@@ -133,8 +131,6 @@
 
 err_dev_add:
 	kfree(sds);
-err_mem:
-	pci_disable_device(dev);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-pxa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-pxa.c
@@ -264,6 +264,9 @@
 	u32			hs_mask;
 
 	struct i2c_bus_recovery_info recovery;
+	struct pinctrl		*pinctrl;
+	struct pinctrl_state	*pinctrl_default;
+	struct pinctrl_state	*pinctrl_recovery;
 };
 
 #define _IBMR(i2c)	((i2c)->reg_ibmr)
@@ -1302,12 +1305,13 @@
 	 */
 	gpiod_set_value(i2c->recovery.scl_gpiod, ibmr & IBMR_SCLS);
 	gpiod_set_value(i2c->recovery.sda_gpiod, ibmr & IBMR_SDAS);
+
+	WARN_ON(pinctrl_select_state(i2c->pinctrl, i2c->pinctrl_recovery));
 }
 
 static void i2c_pxa_unprepare_recovery(struct i2c_adapter *adap)
 {
 	struct pxa_i2c *i2c = adap->algo_data;
-	struct i2c_bus_recovery_info *bri = adap->bus_recovery_info;
 	u32 isr;
 
 	/*
@@ -1321,7 +1325,7 @@
 		i2c_pxa_do_reset(i2c);
 	}
 
-	WARN_ON(pinctrl_select_state(bri->pinctrl, bri->pins_default));
+	WARN_ON(pinctrl_select_state(i2c->pinctrl, i2c->pinctrl_default));
 
 	dev_dbg(&i2c->adap.dev, "recovery: IBMR 0x%08x ISR 0x%08x\n",
 	        readl(_IBMR(i2c)), readl(_ISR(i2c)));
@@ -1343,20 +1347,76 @@
 	if (IS_ENABLED(CONFIG_I2C_PXA_SLAVE))
 		return 0;
 
-	bri->pinctrl = devm_pinctrl_get(dev);
-	if (PTR_ERR(bri->pinctrl) == -ENODEV) {
-		bri->pinctrl = NULL;
+	i2c->pinctrl = devm_pinctrl_get(dev);
+	if (PTR_ERR(i2c->pinctrl) == -ENODEV)
+		i2c->pinctrl = NULL;
+	if (IS_ERR(i2c->pinctrl))
+		return PTR_ERR(i2c->pinctrl);
+
+	if (!i2c->pinctrl)
+		return 0;
+
+	i2c->pinctrl_default = pinctrl_lookup_state(i2c->pinctrl,
+						    PINCTRL_STATE_DEFAULT);
+	i2c->pinctrl_recovery = pinctrl_lookup_state(i2c->pinctrl, "recovery");
+
+	if (IS_ERR(i2c->pinctrl_default) || IS_ERR(i2c->pinctrl_recovery)) {
+		dev_info(dev, "missing pinmux recovery information: %ld %ld\n",
+			 PTR_ERR(i2c->pinctrl_default),
+			 PTR_ERR(i2c->pinctrl_recovery));
+		return 0;
+	}
+
+	/*
+	 * Claiming GPIOs can influence the pinmux state, and may glitch the
+	 * I2C bus. Do this carefully.
+	 */
+	bri->scl_gpiod = devm_gpiod_get(dev, "scl", GPIOD_OUT_HIGH_OPEN_DRAIN);
+	if (bri->scl_gpiod == ERR_PTR(-EPROBE_DEFER))
+		return -EPROBE_DEFER;
+	if (IS_ERR(bri->scl_gpiod)) {
+		dev_info(dev, "missing scl gpio recovery information: %pe\n",
+			 bri->scl_gpiod);
+		return 0;
+	}
+
+	/*
+	 * We have SCL. Pull SCL low and wait a bit so that SDA glitches
+	 * have no effect.
+	 */
+	gpiod_direction_output(bri->scl_gpiod, 0);
+	udelay(10);
+	bri->sda_gpiod = devm_gpiod_get(dev, "sda", GPIOD_OUT_HIGH_OPEN_DRAIN);
+
+	/* Wait a bit in case of a SDA glitch, and then release SCL. */
+	udelay(10);
+	gpiod_direction_output(bri->scl_gpiod, 1);
+
+	if (bri->sda_gpiod == ERR_PTR(-EPROBE_DEFER))
+		return -EPROBE_DEFER;
+
+	if (IS_ERR(bri->sda_gpiod)) {
+		dev_info(dev, "missing sda gpio recovery information: %pe\n",
+			 bri->sda_gpiod);
 		return 0;
 	}
-	if (IS_ERR(bri->pinctrl))
-		return PTR_ERR(bri->pinctrl);
 
 	bri->prepare_recovery = i2c_pxa_prepare_recovery;
 	bri->unprepare_recovery = i2c_pxa_unprepare_recovery;
+	bri->recover_bus = i2c_generic_scl_recovery;
 
 	i2c->adap.bus_recovery_info = bri;
 
-	return 0;
+	/*
+	 * Claiming GPIOs can change the pinmux state, which confuses the
+	 * pinctrl since pinctrl's idea of the current setting is unaffected
+	 * by the pinmux change caused by claiming the GPIO. Work around that
+	 * by switching pinctrl to the GPIO state here. We do it this way to
+	 * avoid glitching the I2C bus.
+	 */
+	pinctrl_select_state(i2c->pinctrl, i2c->pinctrl_recovery);
+
+	return pinctrl_select_state(i2c->pinctrl, i2c->pinctrl_default);
 }
 
 static int i2c_pxa_probe(struct platform_device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-qcom-cci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-qcom-cci.c
@@ -558,7 +558,7 @@
 		cci->master[idx].adap.quirks = &cci->data->quirks;
 		cci->master[idx].adap.algo = &cci_algo;
 		cci->master[idx].adap.dev.parent = dev;
-		cci->master[idx].adap.dev.of_node = child;
+		cci->master[idx].adap.dev.of_node = of_node_get(child);
 		cci->master[idx].master = idx;
 		cci->master[idx].cci = cci;
 
@@ -638,26 +638,33 @@
 	if (ret < 0)
 		goto error;
 
+	pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
 	for (i = 0; i < cci->data->num_masters; i++) {
 		if (!cci->master[i].cci)
 			continue;
 
 		ret = i2c_add_adapter(&cci->master[i].adap);
-		if (ret < 0)
+		if (ret < 0) {
+			of_node_put(cci->master[i].adap.dev.of_node);
 			goto error_i2c;
+		}
 	}
 
-	pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC);
-	pm_runtime_use_autosuspend(dev);
-	pm_runtime_set_active(dev);
-	pm_runtime_enable(dev);
-
 	return 0;
 
 error_i2c:
-	for (; i >= 0; i--) {
-		if (cci->master[i].cci)
+	pm_runtime_disable(dev);
+	pm_runtime_dont_use_autosuspend(dev);
+
+	for (--i ; i >= 0; i--) {
+		if (cci->master[i].cci) {
 			i2c_del_adapter(&cci->master[i].adap);
+			of_node_put(cci->master[i].adap.dev.of_node);
+		}
 	}
 error:
 	disable_irq(cci->irq);
@@ -673,8 +680,10 @@
 	int i;
 
 	for (i = 0; i < cci->data->num_masters; i++) {
-		if (cci->master[i].cci)
+		if (cci->master[i].cci) {
 			i2c_del_adapter(&cci->master[i].adap);
+			of_node_put(cci->master[i].adap.dev.of_node);
+		}
 		cci_halt(cci, i);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-qcom-geni.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-qcom-geni.c
@@ -565,15 +565,13 @@
 	init_completion(&gi2c->done);
 	spin_lock_init(&gi2c->lock);
 	platform_set_drvdata(pdev, gi2c);
-	ret = devm_request_irq(dev, gi2c->irq, geni_i2c_irq, 0,
+	ret = devm_request_irq(dev, gi2c->irq, geni_i2c_irq, IRQF_NO_AUTOEN,
 			       dev_name(dev), gi2c);
 	if (ret) {
 		dev_err(dev, "Request_irq failed:%d: err:%d\n",
 			gi2c->irq, ret);
 		return ret;
 	}
-	/* Disable the interrupt so that the system can enter low-power mode */
-	disable_irq(gi2c->irq);
 	i2c_set_adapdata(&gi2c->adap, gi2c);
 	gi2c->adap.dev.parent = dev;
 	gi2c->adap.dev.of_node = dev->of_node;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-qup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-qup.c
@@ -1752,16 +1752,21 @@
 	if (!clk_freq || clk_freq > I2C_MAX_FAST_MODE_PLUS_FREQ) {
 		dev_err(qup->dev, "clock frequency not supported %d\n",
 			clk_freq);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto fail_dma;
 	}
 
 	qup->base = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(qup->base))
-		return PTR_ERR(qup->base);
+	if (IS_ERR(qup->base)) {
+		ret = PTR_ERR(qup->base);
+		goto fail_dma;
+	}
 
 	qup->irq = platform_get_irq(pdev, 0);
-	if (qup->irq < 0)
-		return qup->irq;
+	if (qup->irq < 0) {
+		ret = qup->irq;
+		goto fail_dma;
+	}
 
 	if (has_acpi_companion(qup->dev)) {
 		ret = device_property_read_u32(qup->dev,
@@ -1775,13 +1780,15 @@
 		qup->clk = devm_clk_get(qup->dev, "core");
 		if (IS_ERR(qup->clk)) {
 			dev_err(qup->dev, "Could not get core clock\n");
-			return PTR_ERR(qup->clk);
+			ret = PTR_ERR(qup->clk);
+			goto fail_dma;
 		}
 
 		qup->pclk = devm_clk_get(qup->dev, "iface");
 		if (IS_ERR(qup->pclk)) {
 			dev_err(qup->dev, "Could not get iface clock\n");
-			return PTR_ERR(qup->pclk);
+			ret = PTR_ERR(qup->pclk);
+			goto fail_dma;
 		}
 		qup_i2c_enable_clocks(qup);
 		src_clk_freq = clk_get_rate(qup->clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-rcar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-rcar.c
@@ -112,10 +112,13 @@
 #define ID_P_PM_BLOCKED		BIT(31)
 #define ID_P_MASK		GENMASK(31, 28)
 
+#define ID_SLAVE_NACK		BIT(0)
+
 enum rcar_i2c_type {
 	I2C_RCAR_GEN1,
 	I2C_RCAR_GEN2,
 	I2C_RCAR_GEN3,
+	I2C_RCAR_GEN4,
 };
 
 struct rcar_i2c_priv {
@@ -145,6 +148,7 @@
 	int irq;
 
 	struct i2c_client *host_notify_client;
+	u8 slave_flags;
 };
 
 #define rcar_i2c_priv_to_dev(p)		((p)->adap.dev.parent)
@@ -221,6 +225,14 @@
 
 }
 
+static void rcar_i2c_reset_slave(struct rcar_i2c_priv *priv)
+{
+	rcar_i2c_write(priv, ICSIER, 0);
+	rcar_i2c_write(priv, ICSSR, 0);
+	rcar_i2c_write(priv, ICSCR, SDBS);
+	rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
+}
+
 static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
 {
 	int ret;
@@ -375,8 +387,8 @@
 	dma_unmap_single(chan->device->dev, sg_dma_address(&priv->sg),
 			 sg_dma_len(&priv->sg), priv->dma_direction);
 
-	/* Gen3 can only do one RXDMA per transfer and we just completed it */
-	if (priv->devtype == I2C_RCAR_GEN3 &&
+	/* Gen3+ can only do one RXDMA per transfer and we just completed it */
+	if (priv->devtype >= I2C_RCAR_GEN3 &&
 	    priv->dma_direction == DMA_FROM_DEVICE)
 		priv->flags |= ID_P_NO_RXDMA;
 
@@ -567,6 +579,7 @@
 {
 	u32 ssr_raw, ssr_filtered;
 	u8 value;
+	int ret;
 
 	ssr_raw = rcar_i2c_read(priv, ICSSR) & 0xff;
 	ssr_filtered = ssr_raw & rcar_i2c_read(priv, ICSIER);
@@ -582,7 +595,10 @@
 			rcar_i2c_write(priv, ICRXTX, value);
 			rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR);
 		} else {
-			i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+			ret = i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+			if (ret)
+				priv->slave_flags |= ID_SLAVE_NACK;
+
 			rcar_i2c_read(priv, ICRXTX);	/* dummy read */
 			rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR);
 		}
@@ -595,18 +611,21 @@
 	if (ssr_filtered & SSR) {
 		i2c_slave_event(priv->slave, I2C_SLAVE_STOP, &value);
 		rcar_i2c_write(priv, ICSCR, SIE | SDBS); /* clear our NACK */
+		priv->slave_flags &= ~ID_SLAVE_NACK;
 		rcar_i2c_write(priv, ICSIER, SAR);
 		rcar_i2c_write(priv, ICSSR, ~SSR & 0xff);
 	}
 
 	/* master wants to write to us */
 	if (ssr_filtered & SDR) {
-		int ret;
-
 		value = rcar_i2c_read(priv, ICRXTX);
 		ret = i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
-		/* Send NACK in case of error */
-		rcar_i2c_write(priv, ICSCR, SIE | SDBS | (ret < 0 ? FNA : 0));
+		if (ret)
+			priv->slave_flags |= ID_SLAVE_NACK;
+
+		/* Send NACK in case of error, but it will come 1 byte late :( */
+		rcar_i2c_write(priv, ICSCR, SIE | SDBS |
+			       (priv->slave_flags & ID_SLAVE_NACK ? FNA : 0));
 		rcar_i2c_write(priv, ICSSR, ~SDR & 0xff);
 	}
 
@@ -794,6 +813,10 @@
 {
 	int ret;
 
+	/* Don't reset if a slave instance is currently running */
+	if (priv->slave)
+		return -EISCONN;
+
 	ret = reset_control_reset(priv->rstc);
 	if (ret)
 		return ret;
@@ -820,14 +843,12 @@
 	if (ret < 0)
 		goto out;
 
-	/* Gen3 needs a reset before allowing RXDMA once */
-	if (priv->devtype == I2C_RCAR_GEN3) {
-		priv->flags |= ID_P_NO_RXDMA;
-		if (!IS_ERR(priv->rstc)) {
-			ret = rcar_i2c_do_reset(priv);
-			if (ret == 0)
-				priv->flags &= ~ID_P_NO_RXDMA;
-		}
+	/* Gen3+ needs a reset. That also allows RXDMA once */
+	if (priv->devtype >= I2C_RCAR_GEN3) {
+		ret = rcar_i2c_do_reset(priv);
+		if (ret)
+			goto out;
+		priv->flags &= ~ID_P_NO_RXDMA;
 	}
 
 	rcar_i2c_init(priv);
@@ -959,11 +980,8 @@
 
 	/* ensure no irq is running before clearing ptr */
 	disable_irq(priv->irq);
-	rcar_i2c_write(priv, ICSIER, 0);
-	rcar_i2c_write(priv, ICSSR, 0);
+	rcar_i2c_reset_slave(priv);
 	enable_irq(priv->irq);
-	rcar_i2c_write(priv, ICSCR, SDBS);
-	rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
 
 	priv->slave = NULL;
 
@@ -1016,6 +1034,7 @@
 	{ .compatible = "renesas,rcar-gen1-i2c", .data = (void *)I2C_RCAR_GEN1 },
 	{ .compatible = "renesas,rcar-gen2-i2c", .data = (void *)I2C_RCAR_GEN2 },
 	{ .compatible = "renesas,rcar-gen3-i2c", .data = (void *)I2C_RCAR_GEN3 },
+	{ .compatible = "renesas,rcar-gen4-i2c", .data = (void *)I2C_RCAR_GEN4 },
 	{},
 };
 MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids);
@@ -1070,25 +1089,20 @@
 	pm_runtime_enable(dev);
 	pm_runtime_get_sync(dev);
 	ret = rcar_i2c_clock_calculate(priv);
-	if (ret < 0)
-		goto out_pm_put;
+	if (ret < 0) {
+		pm_runtime_put(dev);
+		goto out_pm_disable;
+	}
 
-	rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
+	/* Bring hardware to known state */
+	rcar_i2c_init(priv);
+	rcar_i2c_reset_slave(priv);
 
 	if (priv->devtype < I2C_RCAR_GEN3) {
 		irqflags |= IRQF_NO_THREAD;
 		irqhandler = rcar_i2c_gen2_irq;
 	}
 
-	if (priv->devtype == I2C_RCAR_GEN3) {
-		priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
-		if (!IS_ERR(priv->rstc)) {
-			ret = reset_control_status(priv->rstc);
-			if (ret < 0)
-				priv->rstc = ERR_PTR(-ENOTSUPP);
-		}
-	}
-
 	/* Stay always active when multi-master to keep arbitration working */
 	if (of_property_read_bool(dev->of_node, "multi-master"))
 		priv->flags |= ID_P_PM_BLOCKED;
@@ -1098,21 +1112,37 @@
 	if (of_property_read_bool(dev->of_node, "smbus"))
 		priv->flags |= ID_P_HOST_NOTIFY;
 
+	/* R-Car Gen3+ needs a reset before every transfer */
+	if (priv->devtype >= I2C_RCAR_GEN3) {
+		priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+		if (IS_ERR(priv->rstc)) {
+			ret = PTR_ERR(priv->rstc);
+			goto out_pm_put;
+		}
+
+		ret = reset_control_status(priv->rstc);
+		if (ret < 0)
+			goto out_pm_put;
+
+		/* hard reset disturbs HostNotify local target, so disable it */
+		priv->flags &= ~ID_P_HOST_NOTIFY;
+	}
+
 	ret = platform_get_irq(pdev, 0);
 	if (ret < 0)
-		goto out_pm_disable;
+		goto out_pm_put;
 	priv->irq = ret;
 	ret = devm_request_irq(dev, priv->irq, irqhandler, irqflags, dev_name(dev), priv);
 	if (ret < 0) {
 		dev_err(dev, "cannot get irq %d\n", priv->irq);
-		goto out_pm_disable;
+		goto out_pm_put;
 	}
 
 	platform_set_drvdata(pdev, priv);
 
 	ret = i2c_add_numbered_adapter(adap);
 	if (ret < 0)
-		goto out_pm_disable;
+		goto out_pm_put;
 
 	if (priv->flags & ID_P_HOST_NOTIFY) {
 		priv->host_notify_client = i2c_new_slave_host_notify_device(adap);
@@ -1129,7 +1159,8 @@
  out_del_device:
 	i2c_del_adapter(&priv->adap);
  out_pm_put:
-	pm_runtime_put(dev);
+	if (priv->flags & ID_P_PM_BLOCKED)
+		pm_runtime_put(dev);
  out_pm_disable:
 	pm_runtime_disable(dev);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-riic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-riic.c
@@ -319,7 +319,7 @@
 	 * frequency with only 62 clock ticks max (31 high, 31 low).
 	 * Aim for a duty of 60% LOW, 40% HIGH.
 	 */
-	total_ticks = DIV_ROUND_UP(rate, t->bus_freq_hz);
+	total_ticks = DIV_ROUND_UP(rate, t->bus_freq_hz ?: 1);
 
 	for (cks = 0; cks < 7; cks++) {
 		/*
@@ -330,7 +330,7 @@
 		if (brl <= (0x1F + 3))
 			break;
 
-		total_ticks /= 2;
+		total_ticks = DIV_ROUND_UP(total_ticks, 2);
 		rate /= 2;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-rk3x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-rk3x.c
@@ -80,7 +80,7 @@
 #define DEFAULT_SCL_RATE  (100 * 1000) /* Hz */
 
 /**
- * struct i2c_spec_values:
+ * struct i2c_spec_values - I2C specification values for various modes
  * @min_hold_start_ns: min hold time (repeated) START condition
  * @min_low_ns: min LOW period of the SCL clock
  * @min_high_ns: min HIGH period of the SCL cloc
@@ -136,7 +136,7 @@
 };
 
 /**
- * struct rk3x_i2c_calced_timings:
+ * struct rk3x_i2c_calced_timings - calculated V1 timings
  * @div_low: Divider output for low
  * @div_high: Divider output for high
  * @tuning: Used to adjust setup/hold data time,
@@ -159,7 +159,7 @@
 };
 
 /**
- * struct rk3x_i2c_soc_data:
+ * struct rk3x_i2c_soc_data - SOC-specific data
  * @grf_offset: offset inside the grf regmap for setting the i2c type
  * @calc_timings: Callback function for i2c timing information calculated
  */
@@ -178,6 +178,7 @@
  * @clk: function clk for rk3399 or function & Bus clks for others
  * @pclk: Bus clk for rk3399
  * @clk_rate_nb: i2c clk rate change notify
+ * @irq: irq number
  * @t: I2C known timing information
  * @lock: spinlock for the i2c bus
  * @wait: the waitqueue to wait for i2c transfer
@@ -200,6 +201,7 @@
 	struct clk *clk;
 	struct clk *pclk;
 	struct notifier_block clk_rate_nb;
+	int irq;
 
 	/* Settings */
 	struct i2c_timings t;
@@ -239,7 +241,8 @@
 }
 
 /**
- * Generate a START condition, which triggers a REG_INT_START interrupt.
+ * rk3x_i2c_start - Generate a START condition, which triggers a REG_INT_START interrupt.
+ * @i2c: target controller data
  */
 static void rk3x_i2c_start(struct rk3x_i2c *i2c)
 {
@@ -258,8 +261,8 @@
 }
 
 /**
- * Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
- *
+ * rk3x_i2c_stop - Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
+ * @i2c: target controller data
  * @error: Error code to return in rk3x_i2c_xfer
  */
 static void rk3x_i2c_stop(struct rk3x_i2c *i2c, int error)
@@ -298,7 +301,8 @@
 }
 
 /**
- * Setup a read according to i2c->msg
+ * rk3x_i2c_prepare_read - Setup a read according to i2c->msg
+ * @i2c: target controller data
  */
 static void rk3x_i2c_prepare_read(struct rk3x_i2c *i2c)
 {
@@ -329,7 +333,8 @@
 }
 
 /**
- * Fill the transmit buffer with data from i2c->msg
+ * rk3x_i2c_fill_transmit_buf - Fill the transmit buffer with data from i2c->msg
+ * @i2c: target controller data
  */
 static void rk3x_i2c_fill_transmit_buf(struct rk3x_i2c *i2c)
 {
@@ -423,8 +428,8 @@
 	if (!(ipd & REG_INT_MBRF))
 		return;
 
-	/* ack interrupt */
-	i2c_writel(i2c, REG_INT_MBRF, REG_IPD);
+	/* ack interrupt (read also produces a spurious START flag, clear it too) */
+	i2c_writel(i2c, REG_INT_MBRF | REG_INT_START, REG_IPD);
 
 	/* Can only handle a maximum of 32 bytes at a time */
 	if (len > 32)
@@ -532,11 +537,10 @@
 }
 
 /**
- * Get timing values of I2C specification
- *
+ * rk3x_i2c_get_spec - Get timing values of I2C specification
  * @speed: Desired SCL frequency
  *
- * Returns: Matched i2c spec values.
+ * Return: Matched i2c_spec_values.
  */
 static const struct i2c_spec_values *rk3x_i2c_get_spec(unsigned int speed)
 {
@@ -549,13 +553,12 @@
 }
 
 /**
- * Calculate divider values for desired SCL frequency
- *
+ * rk3x_i2c_v0_calc_timings - Calculate divider values for desired SCL frequency
  * @clk_rate: I2C input clock rate
  * @t: Known I2C timing information
  * @t_calc: Caculated rk3x private timings that would be written into regs
  *
- * Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case
+ * Return: %0 on success, -%EINVAL if the goal SCL rate is too slow. In that case
  * a best-effort divider value is returned in divs. If the target rate is
  * too high, we silently use the highest possible rate.
  */
@@ -710,13 +713,12 @@
 }
 
 /**
- * Calculate timing values for desired SCL frequency
- *
+ * rk3x_i2c_v1_calc_timings - Calculate timing values for desired SCL frequency
  * @clk_rate: I2C input clock rate
  * @t: Known I2C timing information
  * @t_calc: Caculated rk3x private timings that would be written into regs
  *
- * Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case
+ * Return: %0 on success, -%EINVAL if the goal SCL rate is too slow. In that case
  * a best-effort divider value is returned in divs. If the target rate is
  * too high, we silently use the highest possible rate.
  * The following formulas are v1's method to calculate timings.
@@ -960,14 +962,14 @@
 }
 
 /**
- * Setup I2C registers for an I2C operation specified by msgs, num.
- *
- * Must be called with i2c->lock held.
- *
+ * rk3x_i2c_setup - Setup I2C registers for an I2C operation specified by msgs, num.
+ * @i2c: target controller data
  * @msgs: I2C msgs to process
  * @num: Number of msgs
  *
- * returns: Number of I2C msgs processed or negative in case of error
+ * Must be called with i2c->lock held.
+ *
+ * Return: Number of I2C msgs processed or negative in case of error
  */
 static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num)
 {
@@ -1087,13 +1089,18 @@
 
 		spin_unlock_irqrestore(&i2c->lock, flags);
 
-		rk3x_i2c_start(i2c);
-
 		if (!polling) {
+			rk3x_i2c_start(i2c);
+
 			timeout = wait_event_timeout(i2c->wait, !i2c->busy,
 						     msecs_to_jiffies(WAIT_TIMEOUT));
 		} else {
+			disable_irq(i2c->irq);
+			rk3x_i2c_start(i2c);
+
 			timeout = rk3x_i2c_wait_xfer_poll(i2c);
+
+			enable_irq(i2c->irq);
 		}
 
 		spin_lock_irqsave(&i2c->lock, flags);
@@ -1301,6 +1308,8 @@
 		return ret;
 	}
 
+	i2c->irq = irq;
+
 	platform_set_drvdata(pdev, i2c);
 
 	if (i2c->soc_data->calc_timings == rk3x_i2c_v0_calc_timings) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-s3c2410.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-s3c2410.c
@@ -220,8 +220,17 @@
 	int tries;
 
 	for (tries = 50; tries; --tries) {
-		if (readl(i2c->regs + S3C2410_IICCON)
-			& S3C2410_IICCON_IRQPEND) {
+		unsigned long tmp = readl(i2c->regs + S3C2410_IICCON);
+
+		if (!(tmp & S3C2410_IICCON_ACKEN)) {
+			/*
+			 * Wait a bit for the bus to stabilize,
+			 * delay estimated experimentally.
+			 */
+			usleep_range(100, 200);
+			return true;
+		}
+		if (tmp & S3C2410_IICCON_IRQPEND) {
 			if (!(readl(i2c->regs + S3C2410_IICSTAT)
 				& S3C2410_IICSTAT_LASTBIT))
 				return true;
@@ -274,16 +283,6 @@
 
 	stat |= S3C2410_IICSTAT_START;
 	writel(stat, i2c->regs + S3C2410_IICSTAT);
-
-	if (i2c->quirks & QUIRK_POLL) {
-		while ((i2c->msg_num != 0) && is_ack(i2c)) {
-			i2c_s3c_irq_nextbyte(i2c, stat);
-			stat = readl(i2c->regs + S3C2410_IICSTAT);
-
-			if (stat & S3C2410_IICSTAT_ARBITR)
-				dev_err(i2c->dev, "deal with arbitration loss\n");
-		}
-	}
 }
 
 static inline void s3c24xx_i2c_stop(struct s3c24xx_i2c *i2c, int ret)
@@ -690,7 +689,7 @@
 static int s3c24xx_i2c_doxfer(struct s3c24xx_i2c *i2c,
 			      struct i2c_msg *msgs, int num)
 {
-	unsigned long timeout;
+	unsigned long timeout = 0;
 	int ret;
 
 	ret = s3c24xx_i2c_set_master(i2c);
@@ -710,16 +709,19 @@
 	s3c24xx_i2c_message_start(i2c, msgs);
 
 	if (i2c->quirks & QUIRK_POLL) {
-		ret = i2c->msg_idx;
+		while ((i2c->msg_num != 0) && is_ack(i2c)) {
+			unsigned long stat = readl(i2c->regs + S3C2410_IICSTAT);
 
-		if (ret != num)
-			dev_dbg(i2c->dev, "incomplete xfer (%d)\n", ret);
+			i2c_s3c_irq_nextbyte(i2c, stat);
 
-		goto out;
+			stat = readl(i2c->regs + S3C2410_IICSTAT);
+			if (stat & S3C2410_IICSTAT_ARBITR)
+				dev_err(i2c->dev, "deal with arbitration loss\n");
+		}
+	} else {
+		timeout = wait_event_timeout(i2c->wait, i2c->msg_num == 0, HZ * 5);
 	}
 
-	timeout = wait_event_timeout(i2c->wait, i2c->msg_num == 0, HZ * 5);
-
 	ret = i2c->msg_idx;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-sh7760.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-sh7760.c
@@ -443,9 +443,8 @@
 		goto out0;
 	}
 
-	id = kzalloc(sizeof(struct cami2c), GFP_KERNEL);
+	id = kzalloc(sizeof(*id), GFP_KERNEL);
 	if (!id) {
-		dev_err(&pdev->dev, "no mem for private data\n");
 		ret = -ENOMEM;
 		goto out0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-sis630.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-sis630.c
@@ -509,6 +509,8 @@
 
 static int sis630_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
+	int ret;
+
 	if (sis630_setup(dev)) {
 		dev_err(&dev->dev,
 			"SIS630 compatible bus not detected, "
@@ -522,7 +524,15 @@
 	snprintf(sis630_adapter.name, sizeof(sis630_adapter.name),
 		 "SMBus SIS630 adapter at %04x", smbus_base + SMB_STS);
 
-	return i2c_add_adapter(&sis630_adapter);
+	ret = i2c_add_adapter(&sis630_adapter);
+	if (ret)
+		goto release_region;
+
+	return 0;
+
+release_region:
+	release_region(smbus_base + SMB_STS, SIS630_SMB_IOREGION);
+	return ret;
 }
 
 static void sis630_remove(struct pci_dev *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-sprd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-sprd.c
@@ -576,12 +576,14 @@
 	struct sprd_i2c *i2c_dev = platform_get_drvdata(pdev);
 	int ret;
 
-	ret = pm_runtime_resume_and_get(i2c_dev->dev);
+	ret = pm_runtime_get_sync(i2c_dev->dev);
 	if (ret < 0)
-		return ret;
+		dev_err(&pdev->dev, "Failed to resume device (%pe)\n", ERR_PTR(ret));
 
 	i2c_del_adapter(&i2c_dev->adap);
-	clk_disable_unprepare(i2c_dev->clk);
+
+	if (ret >= 0)
+		clk_disable_unprepare(i2c_dev->clk);
 
 	pm_runtime_put_noidle(i2c_dev->dev);
 	pm_runtime_disable(i2c_dev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-stm32f7.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-stm32f7.c
@@ -1063,9 +1063,10 @@
 	/* Configure PEC */
 	if ((flags & I2C_CLIENT_PEC) && f7_msg->size != I2C_SMBUS_QUICK) {
 		cr1 |= STM32F7_I2C_CR1_PECEN;
-		cr2 |= STM32F7_I2C_CR2_PECBYTE;
-		if (!f7_msg->read_write)
+		if (!f7_msg->read_write) {
+			cr2 |= STM32F7_I2C_CR2_PECBYTE;
 			f7_msg->count++;
+		}
 	} else {
 		cr1 &= ~STM32F7_I2C_CR1_PECEN;
 		cr2 &= ~STM32F7_I2C_CR2_PECBYTE;
@@ -1153,8 +1154,10 @@
 	f7_msg->stop = true;
 
 	/* Add one byte for PEC if needed */
-	if (cr1 & STM32F7_I2C_CR1_PECEN)
+	if (cr1 & STM32F7_I2C_CR1_PECEN) {
+		cr2 |= STM32F7_I2C_CR2_PECBYTE;
 		f7_msg->count++;
+	}
 
 	/* Set number of bytes to be transferred */
 	cr2 &= ~(STM32F7_I2C_CR2_NBYTES_MASK);
@@ -1493,6 +1496,7 @@
 {
 	struct stm32f7_i2c_dev *i2c_dev = data;
 	struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
+	struct stm32_i2c_dma *dma = i2c_dev->dma;
 	void __iomem *base = i2c_dev->base;
 	u32 status, mask;
 	int ret = IRQ_HANDLED;
@@ -1518,6 +1522,10 @@
 		dev_dbg(i2c_dev->dev, "<%s>: Receive NACK (addr %x)\n",
 			__func__, f7_msg->addr);
 		writel_relaxed(STM32F7_I2C_ICR_NACKCF, base + STM32F7_I2C_ICR);
+		if (i2c_dev->use_dma) {
+			stm32f7_i2c_disable_dma_req(i2c_dev);
+			dmaengine_terminate_all(dma->chan_using);
+		}
 		f7_msg->result = -ENXIO;
 	}
 
@@ -1533,7 +1541,7 @@
 		/* Clear STOP flag */
 		writel_relaxed(STM32F7_I2C_ICR_STOPCF, base + STM32F7_I2C_ICR);
 
-		if (i2c_dev->use_dma) {
+		if (i2c_dev->use_dma && !f7_msg->result) {
 			ret = IRQ_WAKE_THREAD;
 		} else {
 			i2c_dev->master_mode = false;
@@ -1546,7 +1554,7 @@
 		if (f7_msg->stop) {
 			mask = STM32F7_I2C_CR2_STOP;
 			stm32f7_i2c_set_bits(base + STM32F7_I2C_CR2, mask);
-		} else if (i2c_dev->use_dma) {
+		} else if (i2c_dev->use_dma && !f7_msg->result) {
 			ret = IRQ_WAKE_THREAD;
 		} else if (f7_msg->smbus) {
 			stm32f7_i2c_smbus_rep_start(i2c_dev);
@@ -1696,12 +1704,23 @@
 	time_left = wait_for_completion_timeout(&i2c_dev->complete,
 						i2c_dev->adap.timeout);
 	ret = f7_msg->result;
+	if (ret) {
+		/*
+		 * It is possible that some unsent data have already been
+		 * written into TXDR. To avoid sending old data in a
+		 * further transfer, flush TXDR in case of any error
+		 */
+		writel_relaxed(STM32F7_I2C_ISR_TXE,
+			       i2c_dev->base + STM32F7_I2C_ISR);
+		goto pm_free;
+	}
 
 	if (!time_left) {
 		dev_dbg(i2c_dev->dev, "Access to slave 0x%x timed out\n",
 			i2c_dev->msg->addr);
 		if (i2c_dev->use_dma)
 			dmaengine_terminate_all(dma->chan_using);
+		stm32f7_i2c_wait_free_bus(i2c_dev);
 		ret = -ETIMEDOUT;
 	}
 
@@ -1744,13 +1763,22 @@
 	timeout = wait_for_completion_timeout(&i2c_dev->complete,
 					      i2c_dev->adap.timeout);
 	ret = f7_msg->result;
-	if (ret)
+	if (ret) {
+		/*
+		 * It is possible that some unsent data have already been
+		 * written into TXDR. To avoid sending old data in a
+		 * further transfer, flush TXDR in case of any error
+		 */
+		writel_relaxed(STM32F7_I2C_ISR_TXE,
+			       i2c_dev->base + STM32F7_I2C_ISR);
 		goto pm_free;
+	}
 
 	if (!timeout) {
 		dev_dbg(dev, "Access to slave 0x%x timed out\n", f7_msg->addr);
 		if (i2c_dev->use_dma)
 			dmaengine_terminate_all(dma->chan_using);
+		stm32f7_i2c_wait_free_bus(i2c_dev);
 		ret = -ETIMEDOUT;
 		goto pm_free;
 	}
@@ -2323,7 +2351,7 @@
 	struct stm32f7_i2c_dev *i2c_dev = dev_get_drvdata(dev);
 
 	if (!stm32f7_i2c_is_slave_registered(i2c_dev))
-		clk_disable_unprepare(i2c_dev->clk);
+		clk_disable(i2c_dev->clk);
 
 	return 0;
 }
@@ -2334,9 +2362,9 @@
 	int ret;
 
 	if (!stm32f7_i2c_is_slave_registered(i2c_dev)) {
-		ret = clk_prepare_enable(i2c_dev->clk);
+		ret = clk_enable(i2c_dev->clk);
 		if (ret) {
-			dev_err(dev, "failed to prepare_enable clock\n");
+			dev_err(dev, "failed to enable clock\n");
 			return ret;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-sun6i-p2wi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-sun6i-p2wi.c
@@ -201,6 +201,11 @@
 		return -EINVAL;
 	}
 
+	if (clk_freq == 0) {
+		dev_err(dev, "clock-frequency is set to 0 in DT\n");
+		return -EINVAL;
+	}
+
 	if (of_get_child_count(np) > 1) {
 		dev_err(dev, "P2WI only supports one slave device\n");
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-tegra.c
@@ -283,6 +283,7 @@
 	struct dma_chan *tx_dma_chan;
 	struct dma_chan *rx_dma_chan;
 	unsigned int dma_buf_size;
+	struct device *dma_dev;
 	dma_addr_t dma_phys;
 	void *dma_buf;
 
@@ -419,7 +420,7 @@
 static void tegra_i2c_release_dma(struct tegra_i2c_dev *i2c_dev)
 {
 	if (i2c_dev->dma_buf) {
-		dma_free_coherent(i2c_dev->dev, i2c_dev->dma_buf_size,
+		dma_free_coherent(i2c_dev->dma_dev, i2c_dev->dma_buf_size,
 				  i2c_dev->dma_buf, i2c_dev->dma_phys);
 		i2c_dev->dma_buf = NULL;
 	}
@@ -466,10 +467,13 @@
 
 	i2c_dev->tx_dma_chan = chan;
 
+	WARN_ON(i2c_dev->tx_dma_chan->device != i2c_dev->rx_dma_chan->device);
+	i2c_dev->dma_dev = chan->device->dev;
+
 	i2c_dev->dma_buf_size = i2c_dev->hw->quirks->max_write_len +
 				I2C_PACKET_HEADER_SIZE;
 
-	dma_buf = dma_alloc_coherent(i2c_dev->dev, i2c_dev->dma_buf_size,
+	dma_buf = dma_alloc_coherent(i2c_dev->dma_dev, i2c_dev->dma_buf_size,
 				     &dma_phys, GFP_KERNEL | __GFP_NOWARN);
 	if (!dma_buf) {
 		dev_err(i2c_dev->dev, "failed to allocate DMA buffer\n");
@@ -1255,7 +1259,7 @@
 
 	if (i2c_dev->dma_mode) {
 		if (i2c_dev->msg_read) {
-			dma_sync_single_for_device(i2c_dev->dev,
+			dma_sync_single_for_device(i2c_dev->dma_dev,
 						   i2c_dev->dma_phys,
 						   xfer_size, DMA_FROM_DEVICE);
 
@@ -1263,7 +1267,7 @@
 			if (err)
 				return err;
 		} else {
-			dma_sync_single_for_cpu(i2c_dev->dev,
+			dma_sync_single_for_cpu(i2c_dev->dma_dev,
 						i2c_dev->dma_phys,
 						xfer_size, DMA_TO_DEVICE);
 		}
@@ -1276,7 +1280,7 @@
 			memcpy(i2c_dev->dma_buf + I2C_PACKET_HEADER_SIZE,
 			       msg->buf, msg->len);
 
-			dma_sync_single_for_device(i2c_dev->dev,
+			dma_sync_single_for_device(i2c_dev->dma_dev,
 						   i2c_dev->dma_phys,
 						   xfer_size, DMA_TO_DEVICE);
 
@@ -1327,7 +1331,7 @@
 		}
 
 		if (i2c_dev->msg_read && i2c_dev->msg_err == I2C_ERR_NONE) {
-			dma_sync_single_for_cpu(i2c_dev->dev,
+			dma_sync_single_for_cpu(i2c_dev->dma_dev,
 						i2c_dev->dma_phys,
 						xfer_size, DMA_FROM_DEVICE);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-thunderx-pcidrv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-thunderx-pcidrv.c
@@ -213,6 +213,7 @@
 	i2c->adap.bus_recovery_info = &octeon_i2c_recovery_info;
 	i2c->adap.dev.parent = dev;
 	i2c->adap.dev.of_node = pdev->dev.of_node;
+	i2c->adap.dev.fwnode = dev->fwnode;
 	snprintf(i2c->adap.name, sizeof(i2c->adap.name),
 		 "Cavium ThunderX i2c adapter at %s", dev_name(dev));
 	i2c_set_adapdata(&i2c->adap, i2c);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-tiny-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-tiny-usb.c
@@ -226,10 +226,8 @@
 
 	/* allocate memory for our device state and initialize it */
 	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
-	if (dev == NULL) {
-		dev_err(&interface->dev, "Out of memory\n");
+	if (!dev)
 		goto error;
-	}
 
 	dev->usb_dev = usb_get_dev(interface_to_usbdev(interface));
 	dev->interface = interface;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-virtio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-virtio.c
@@ -22,24 +22,24 @@
 /**
  * struct virtio_i2c - virtio I2C data
  * @vdev: virtio device for this controller
- * @completion: completion of virtio I2C message
  * @adap: I2C adapter for this controller
  * @vq: the virtio virtqueue for communication
  */
 struct virtio_i2c {
 	struct virtio_device *vdev;
-	struct completion completion;
 	struct i2c_adapter adap;
 	struct virtqueue *vq;
 };
 
 /**
  * struct virtio_i2c_req - the virtio I2C request structure
+ * @completion: completion of virtio I2C message
  * @out_hdr: the OUT header of the virtio I2C message
  * @buf: the buffer into which data is read, or from which it's written
  * @in_hdr: the IN header of the virtio I2C message
  */
 struct virtio_i2c_req {
+	struct completion completion;
 	struct virtio_i2c_out_hdr out_hdr	____cacheline_aligned;
 	uint8_t *buf				____cacheline_aligned;
 	struct virtio_i2c_in_hdr in_hdr		____cacheline_aligned;
@@ -47,9 +47,11 @@
 
 static void virtio_i2c_msg_done(struct virtqueue *vq)
 {
-	struct virtio_i2c *vi = vq->vdev->priv;
+	struct virtio_i2c_req *req;
+	unsigned int len;
 
-	complete(&vi->completion);
+	while ((req = virtqueue_get_buf(vq, &len)))
+		complete(&req->completion);
 }
 
 static int virtio_i2c_prepare_reqs(struct virtqueue *vq,
@@ -62,6 +64,8 @@
 	for (i = 0; i < num; i++) {
 		int outcnt = 0, incnt = 0;
 
+		init_completion(&reqs[i].completion);
+
 		/*
 		 * We don't support 0 length messages and so filter out
 		 * 0 length transfers by using i2c_adapter_quirks.
@@ -106,24 +110,17 @@
 
 static int virtio_i2c_complete_reqs(struct virtqueue *vq,
 				    struct virtio_i2c_req *reqs,
-				    struct i2c_msg *msgs, int num,
-				    bool timedout)
+				    struct i2c_msg *msgs, int num)
 {
-	struct virtio_i2c_req *req;
-	bool failed = timedout;
-	unsigned int len;
+	bool failed = false;
 	int i, j = 0;
 
 	for (i = 0; i < num; i++) {
-		/* Detach the ith request from the vq */
-		req = virtqueue_get_buf(vq, &len);
+		struct virtio_i2c_req *req = &reqs[i];
 
-		/*
-		 * Condition req == &reqs[i] should always meet since we have
-		 * total num requests in the vq. reqs[i] can never be NULL here.
-		 */
-		if (!failed && (WARN_ON(req != &reqs[i]) ||
-				req->in_hdr.status != VIRTIO_I2C_MSG_OK))
+		wait_for_completion(&req->completion);
+
+		if (!failed && req->in_hdr.status != VIRTIO_I2C_MSG_OK)
 			failed = true;
 
 		i2c_put_dma_safe_msg_buf(reqs[i].buf, &msgs[i], !failed);
@@ -132,7 +129,7 @@
 			j++;
 	}
 
-	return timedout ? -ETIMEDOUT : j;
+	return j;
 }
 
 static int virtio_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
@@ -141,7 +138,6 @@
 	struct virtio_i2c *vi = i2c_get_adapdata(adap);
 	struct virtqueue *vq = vi->vq;
 	struct virtio_i2c_req *reqs;
-	unsigned long time_left;
 	int count;
 
 	reqs = kcalloc(num, sizeof(*reqs), GFP_KERNEL);
@@ -160,15 +156,9 @@
 	 * remote here to clear the virtqueue, so we can try another set of
 	 * messages later on.
 	 */
-
-	reinit_completion(&vi->completion);
 	virtqueue_kick(vq);
 
-	time_left = wait_for_completion_timeout(&vi->completion, adap->timeout);
-	if (!time_left)
-		dev_err(&adap->dev, "virtio i2c backend timeout.\n");
-
-	count = virtio_i2c_complete_reqs(vq, reqs, msgs, count, !time_left);
+	count = virtio_i2c_complete_reqs(vq, reqs, msgs, count);
 
 err_free:
 	kfree(reqs);
@@ -215,8 +205,6 @@
 	vdev->priv = vi;
 	vi->vdev = vdev;
 
-	init_completion(&vi->completion);
-
 	ret = virtio_i2c_setup_vqs(vi);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-xgene-slimpro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-xgene-slimpro.c
@@ -307,6 +307,9 @@
 	u32 msg[3];
 	int rc;
 
+	if (writelen > I2C_SMBUS_BLOCK_MAX)
+		return -EINVAL;
+
 	memcpy(ctx->dma_buffer, data, writelen);
 	paddr = dma_map_single(ctx->dev, ctx->dma_buffer, writelen,
 			       DMA_TO_DEVICE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-xiic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-xiic.c
@@ -33,6 +33,8 @@
 
 #define DRIVER_NAME "xiic-i2c"
 
+#define DYNAMIC_MODE_READ_BROKEN_BIT	BIT(0)
+
 enum xilinx_i2c_state {
 	STATE_DONE,
 	STATE_ERROR,
@@ -60,6 +62,12 @@
  * @clk: Pointer to AXI4-lite input clock
  * @state: See STATE_
  * @singlemaster: Indicates bus is single master
+ * @dynamic: Mode of controller
+ * @prev_msg_tx: Previous message is Tx
+ * @smbus_block_read: Flag to handle block read
+ * @quirks: To hold platform specific bug info
+ * @input_clk: Input clock to I2C controller
+ * @i2c_clk: I2C SCL frequency
  */
 struct xiic_i2c {
 	struct device *dev;
@@ -76,26 +84,64 @@
 	struct clk *clk;
 	enum xilinx_i2c_state state;
 	bool singlemaster;
+	bool dynamic;
+	bool prev_msg_tx;
+	bool smbus_block_read;
+	u32 quirks;
+	unsigned long input_clk;
+	unsigned int i2c_clk;
+};
+
+struct xiic_version_data {
+	u32 quirks;
 };
 
+/**
+ * struct timing_regs - AXI I2C timing registers that depend on I2C spec
+ * @tsusta: setup time for a repeated START condition
+ * @tsusto: setup time for a STOP condition
+ * @thdsta: hold time for a repeated START condition
+ * @tsudat: setup time for data
+ * @tbuf: bus free time between STOP and START
+ */
+struct timing_regs {
+	unsigned int tsusta;
+	unsigned int tsusto;
+	unsigned int thdsta;
+	unsigned int tsudat;
+	unsigned int tbuf;
+};
 
 #define XIIC_MSB_OFFSET 0
-#define XIIC_REG_OFFSET (0x100+XIIC_MSB_OFFSET)
+#define XIIC_REG_OFFSET (0x100 + XIIC_MSB_OFFSET)
 
 /*
  * Register offsets in bytes from RegisterBase. Three is added to the
  * base offset to access LSB (IBM style) of the word
  */
-#define XIIC_CR_REG_OFFSET   (0x00+XIIC_REG_OFFSET)	/* Control Register   */
-#define XIIC_SR_REG_OFFSET   (0x04+XIIC_REG_OFFSET)	/* Status Register    */
-#define XIIC_DTR_REG_OFFSET  (0x08+XIIC_REG_OFFSET)	/* Data Tx Register   */
-#define XIIC_DRR_REG_OFFSET  (0x0C+XIIC_REG_OFFSET)	/* Data Rx Register   */
-#define XIIC_ADR_REG_OFFSET  (0x10+XIIC_REG_OFFSET)	/* Address Register   */
-#define XIIC_TFO_REG_OFFSET  (0x14+XIIC_REG_OFFSET)	/* Tx FIFO Occupancy  */
-#define XIIC_RFO_REG_OFFSET  (0x18+XIIC_REG_OFFSET)	/* Rx FIFO Occupancy  */
-#define XIIC_TBA_REG_OFFSET  (0x1C+XIIC_REG_OFFSET)	/* 10 Bit Address reg */
-#define XIIC_RFD_REG_OFFSET  (0x20+XIIC_REG_OFFSET)	/* Rx FIFO Depth reg  */
-#define XIIC_GPO_REG_OFFSET  (0x24+XIIC_REG_OFFSET)	/* Output Register    */
+#define XIIC_CR_REG_OFFSET   (0x00 + XIIC_REG_OFFSET)	/* Control Register   */
+#define XIIC_SR_REG_OFFSET   (0x04 + XIIC_REG_OFFSET)	/* Status Register    */
+#define XIIC_DTR_REG_OFFSET  (0x08 + XIIC_REG_OFFSET)	/* Data Tx Register   */
+#define XIIC_DRR_REG_OFFSET  (0x0C + XIIC_REG_OFFSET)	/* Data Rx Register   */
+#define XIIC_ADR_REG_OFFSET  (0x10 + XIIC_REG_OFFSET)	/* Address Register   */
+#define XIIC_TFO_REG_OFFSET  (0x14 + XIIC_REG_OFFSET)	/* Tx FIFO Occupancy  */
+#define XIIC_RFO_REG_OFFSET  (0x18 + XIIC_REG_OFFSET)	/* Rx FIFO Occupancy  */
+#define XIIC_TBA_REG_OFFSET  (0x1C + XIIC_REG_OFFSET)	/* 10 Bit Address reg */
+#define XIIC_RFD_REG_OFFSET  (0x20 + XIIC_REG_OFFSET)	/* Rx FIFO Depth reg  */
+#define XIIC_GPO_REG_OFFSET  (0x24 + XIIC_REG_OFFSET)	/* Output Register    */
+
+/*
+ * Timing register offsets from RegisterBase. These are used only for
+ * setting i2c clock frequency for the line.
+ */
+#define XIIC_TSUSTA_REG_OFFSET	(0x28 + XIIC_REG_OFFSET) /* TSUSTA Register */
+#define XIIC_TSUSTO_REG_OFFSET	(0x2C + XIIC_REG_OFFSET) /* TSUSTO Register */
+#define XIIC_THDSTA_REG_OFFSET	(0x30 + XIIC_REG_OFFSET) /* THDSTA Register */
+#define XIIC_TSUDAT_REG_OFFSET	(0x34 + XIIC_REG_OFFSET) /* TSUDAT Register */
+#define XIIC_TBUF_REG_OFFSET	(0x38 + XIIC_REG_OFFSET) /* TBUF Register */
+#define XIIC_THIGH_REG_OFFSET	(0x3C + XIIC_REG_OFFSET) /* THIGH Register */
+#define XIIC_TLOW_REG_OFFSET	(0x40 + XIIC_REG_OFFSET) /* TLOW Register */
+#define XIIC_THDDAT_REG_OFFSET	(0x44 + XIIC_REG_OFFSET) /* THDDAT Register */
 
 /* Control Register masks */
 #define XIIC_CR_ENABLE_DEVICE_MASK        0x01	/* Device enable = 1      */
@@ -144,6 +190,9 @@
 #define XIIC_TX_DYN_START_MASK            0x0100 /* 1 = Set dynamic start */
 #define XIIC_TX_DYN_STOP_MASK             0x0200 /* 1 = Set dynamic stop */
 
+/* Dynamic mode constants */
+#define MAX_READ_LENGTH_DYNAMIC		255 /* Max length for dynamic read */
+
 /*
  * The following constants define the register offsets for the Interrupt
  * registers. There are some holes in the memory map for reserved addresses
@@ -172,6 +221,7 @@
 
 static int xiic_start_xfer(struct xiic_i2c *i2c);
 static void __xiic_start_xfer(struct xiic_i2c *i2c);
+static int xiic_setclk(struct xiic_i2c *i2c);
 
 /*
  * For the register read and write functions, a little-endian and big-endian
@@ -230,18 +280,21 @@
 static inline void xiic_irq_dis(struct xiic_i2c *i2c, u32 mask)
 {
 	u32 ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET);
+
 	xiic_setreg32(i2c, XIIC_IIER_OFFSET, ier & ~mask);
 }
 
 static inline void xiic_irq_en(struct xiic_i2c *i2c, u32 mask)
 {
 	u32 ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET);
+
 	xiic_setreg32(i2c, XIIC_IIER_OFFSET, ier | mask);
 }
 
 static inline void xiic_irq_clr(struct xiic_i2c *i2c, u32 mask)
 {
 	u32 isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET);
+
 	xiic_setreg32(i2c, XIIC_IISR_OFFSET, isr & mask);
 }
 
@@ -270,12 +323,34 @@
 	return 0;
 }
 
+static int xiic_wait_tx_empty(struct xiic_i2c *i2c)
+{
+	u8 isr;
+	unsigned long timeout;
+
+	timeout = jiffies + XIIC_I2C_TIMEOUT;
+	for (isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET);
+			!(isr & XIIC_INTR_TX_EMPTY_MASK);
+			isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET)) {
+		if (time_after(jiffies, timeout)) {
+			dev_err(i2c->dev, "Timeout waiting at Tx empty\n");
+			return -ETIMEDOUT;
+		}
+	}
+
+	return 0;
+}
+
 static int xiic_reinit(struct xiic_i2c *i2c)
 {
 	int ret;
 
 	xiic_setreg32(i2c, XIIC_RESETR_OFFSET, XIIC_RESET_MASK);
 
+	ret = xiic_setclk(i2c);
+	if (ret)
+		return ret;
+
 	/* Set receive Fifo depth to maximum (zero based). */
 	xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, IIC_RX_FIFO_DEPTH - 1);
 
@@ -309,15 +384,64 @@
 	xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr & ~XIIC_CR_ENABLE_DEVICE_MASK);
 }
 
+static void xiic_smbus_block_read_setup(struct xiic_i2c *i2c)
+{
+	u8 rxmsg_len;
+	u8 rfd_set = 0;
+
+	/*
+	 * Clear the I2C_M_RECV_LEN flag to avoid setting
+	 * message length again
+	 */
+	i2c->rx_msg->flags &= ~I2C_M_RECV_LEN;
+
+	/* Set smbus_block_read flag to identify in isr */
+	i2c->smbus_block_read = true;
+
+	/* Read byte from rx fifo and set message length */
+	rxmsg_len  = xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
+
+	i2c->rx_msg->buf[i2c->rx_pos++] = rxmsg_len;
+
+	/* Check if received length is valid */
+	if (rxmsg_len <= I2C_SMBUS_BLOCK_MAX) {
+		/* Set Receive fifo depth */
+		if (rxmsg_len > IIC_RX_FIFO_DEPTH) {
+			rfd_set = IIC_RX_FIFO_DEPTH - 1;
+			i2c->rx_msg->len = rxmsg_len + 1;
+		} else if ((rxmsg_len == 1) ||
+			   (rxmsg_len == 0)) {
+			/*
+			 * Minimum of 3 bytes required to exit cleanly. 1 byte
+			 * already received, Second byte is being received. Have
+			 * to set NACK in read_rx before receiving the last byte
+			 */
+			i2c->rx_msg->len = 3;
+		} else {
+			rfd_set = rxmsg_len - 2;
+			i2c->rx_msg->len = rxmsg_len + 1;
+		}
+		xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rfd_set);
+
+		return;
+	}
+
+	/* Invalid message length, trigger STATE_ERROR with tx_msg_len in ISR */
+	i2c->tx_msg->len = 3;
+	i2c->smbus_block_read = false;
+	dev_err(i2c->adap.dev.parent, "smbus_block_read Invalid msg length\n");
+}
+
 static void xiic_read_rx(struct xiic_i2c *i2c)
 {
-	u8 bytes_in_fifo;
+	u8 bytes_in_fifo, cr = 0, bytes_to_read = 0;
+	u32 bytes_rem = 0;
 	int i;
 
 	bytes_in_fifo = xiic_getreg8(i2c, XIIC_RFO_REG_OFFSET) + 1;
 
 	dev_dbg(i2c->adap.dev.parent,
-		"%s entry, bytes in fifo: %d, msg: %d, SR: 0x%x, CR: 0x%x\n",
+		"%s entry, bytes in fifo: %d, rem: %d, SR: 0x%x, CR: 0x%x\n",
 		__func__, bytes_in_fifo, xiic_rx_space(i2c),
 		xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
 		xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
@@ -325,13 +449,59 @@
 	if (bytes_in_fifo > xiic_rx_space(i2c))
 		bytes_in_fifo = xiic_rx_space(i2c);
 
-	for (i = 0; i < bytes_in_fifo; i++)
+	bytes_to_read = bytes_in_fifo;
+
+	if (!i2c->dynamic) {
+		bytes_rem = xiic_rx_space(i2c) - bytes_in_fifo;
+
+		/* Set msg length if smbus_block_read */
+		if (i2c->rx_msg->flags & I2C_M_RECV_LEN) {
+			xiic_smbus_block_read_setup(i2c);
+			return;
+		}
+
+		if (bytes_rem > IIC_RX_FIFO_DEPTH) {
+			bytes_to_read = bytes_in_fifo;
+		} else if (bytes_rem > 1) {
+			bytes_to_read = bytes_rem - 1;
+		} else if (bytes_rem == 1) {
+			bytes_to_read = 1;
+			/* Set NACK in CR to indicate slave transmitter */
+			cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr |
+				     XIIC_CR_NO_ACK_MASK);
+		} else if (bytes_rem == 0) {
+			bytes_to_read = bytes_in_fifo;
+
+			/* Generate stop on the bus if it is last message */
+			if (i2c->nmsgs == 1) {
+				cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+				xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
+					     ~XIIC_CR_MSMS_MASK);
+			}
+
+			/* Make TXACK=0, clean up for next transaction */
+			cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
+				     ~XIIC_CR_NO_ACK_MASK);
+		}
+	}
+
+	/* Read the fifo */
+	for (i = 0; i < bytes_to_read; i++) {
 		i2c->rx_msg->buf[i2c->rx_pos++] =
 			xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
+	}
+
+	if (i2c->dynamic) {
+		u8 bytes;
+
+		/* Receive remaining bytes if less than fifo depth */
+		bytes = min_t(u8, xiic_rx_space(i2c), IIC_RX_FIFO_DEPTH);
+		bytes--;
 
-	xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET,
-		(xiic_rx_space(i2c) > IIC_RX_FIFO_DEPTH) ?
-		IIC_RX_FIFO_DEPTH - 1 :  xiic_rx_space(i2c) - 1);
+		xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
+	}
 }
 
 static int xiic_tx_fifo_space(struct xiic_i2c *i2c)
@@ -352,7 +522,8 @@
 
 	while (len--) {
 		u16 data = i2c->tx_msg->buf[i2c->tx_pos++];
-		if ((xiic_tx_space(i2c) == 0) && (i2c->nmsgs == 1)) {
+
+		if (!xiic_tx_space(i2c) && i2c->nmsgs == 1) {
 			/* last message in transfer -> STOP */
 			data |= XIIC_TX_DYN_STOP_MASK;
 			dev_dbg(i2c->adap.dev.parent, "%s TX STOP\n", __func__);
@@ -361,7 +532,63 @@
 	}
 }
 
-static void xiic_wakeup(struct xiic_i2c *i2c, int code)
+static void xiic_std_fill_tx_fifo(struct xiic_i2c *i2c)
+{
+	u8 fifo_space = xiic_tx_fifo_space(i2c);
+	u16 data = 0;
+	int len = xiic_tx_space(i2c);
+
+	dev_dbg(i2c->adap.dev.parent, "%s entry, len: %d, fifo space: %d\n",
+		__func__, len, fifo_space);
+
+	if (len > fifo_space)
+		len = fifo_space;
+	else if (len && !(i2c->nmsgs > 1))
+		len--;
+
+	while (len--) {
+		data = i2c->tx_msg->buf[i2c->tx_pos++];
+		xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
+	}
+}
+
+static void xiic_send_tx(struct xiic_i2c *i2c)
+{
+	dev_dbg(i2c->adap.dev.parent,
+		"%s entry, rem: %d, SR: 0x%x, CR: 0x%x\n",
+		__func__, xiic_tx_space(i2c),
+		xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
+		xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
+
+	if (xiic_tx_space(i2c) > 1) {
+		xiic_std_fill_tx_fifo(i2c);
+		return;
+	}
+
+	if ((xiic_tx_space(i2c) == 1)) {
+		u16 data;
+
+		if (i2c->nmsgs == 1) {
+			u8 cr;
+			int status;
+
+			/* Wait till FIFO is empty so STOP is sent last */
+			status = xiic_wait_tx_empty(i2c);
+			if (status)
+				return;
+
+			/* Write to CR to stop */
+			cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
+				     ~XIIC_CR_MSMS_MASK);
+		}
+		/* Send last byte */
+		data = i2c->tx_msg->buf[i2c->tx_pos++];
+		xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
+	}
+}
+
+static void xiic_wakeup(struct xiic_i2c *i2c, enum xilinx_i2c_state code)
 {
 	i2c->tx_msg = NULL;
 	i2c->rx_msg = NULL;
@@ -375,6 +602,10 @@
 	struct xiic_i2c *i2c = dev_id;
 	u32 pend, isr, ier;
 	u32 clr = 0;
+	int xfer_more = 0;
+	int wakeup_req = 0;
+	int wakeup_code = 0;
+	int ret;
 
 	/* Get the interrupt Status from the IPIF. There is no clearing of
 	 * interrupts in the IPIF. Interrupts must be cleared at the source.
@@ -391,12 +622,14 @@
 	dev_dbg(i2c->adap.dev.parent, "%s: SR: 0x%x, msg: %p, nmsgs: %d\n",
 		__func__, xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
 		i2c->tx_msg, i2c->nmsgs);
-
+	dev_dbg(i2c->adap.dev.parent, "%s, ISR: 0x%x, CR: 0x%x\n",
+		__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
+		xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
 
 	/* Service requesting interrupt */
 	if ((pend & XIIC_INTR_ARB_LOST_MASK) ||
-		((pend & XIIC_INTR_TX_ERROR_MASK) &&
-		!(pend & XIIC_INTR_RX_FULL_MASK))) {
+	    ((pend & XIIC_INTR_TX_ERROR_MASK) &&
+	    !(pend & XIIC_INTR_RX_FULL_MASK))) {
 		/* bus arbritration lost, or...
 		 * Transmit error _OR_ RX completed
 		 * if this happens when RX_FULL is not set
@@ -409,12 +642,20 @@
 		 * fifos and the next message is a TX with len 0 (only addr)
 		 * reset the IP instead of just flush fifos
 		 */
-		xiic_reinit(i2c);
-
-		if (i2c->rx_msg)
-			xiic_wakeup(i2c, STATE_ERROR);
-		if (i2c->tx_msg)
-			xiic_wakeup(i2c, STATE_ERROR);
+		ret = xiic_reinit(i2c);
+		if (!ret)
+			dev_dbg(i2c->adap.dev.parent, "reinit failed\n");
+
+		if (i2c->rx_msg) {
+			wakeup_req = 1;
+			wakeup_code = STATE_ERROR;
+		}
+		if (i2c->tx_msg) {
+			wakeup_req = 1;
+			wakeup_code = STATE_ERROR;
+		}
+		/* don't try to handle other events */
+		goto out;
 	}
 	if (pend & XIIC_INTR_RX_FULL_MASK) {
 		/* Receive register/FIFO is full */
@@ -448,27 +689,10 @@
 				i2c->tx_msg++;
 				dev_dbg(i2c->adap.dev.parent,
 					"%s will start next...\n", __func__);
-
-				__xiic_start_xfer(i2c);
+				xfer_more = 1;
 			}
 		}
 	}
-	if (pend & XIIC_INTR_BNB_MASK) {
-		/* IIC bus has transitioned to not busy */
-		clr |= XIIC_INTR_BNB_MASK;
-
-		/* The bus is not busy, disable BusNotBusy interrupt */
-		xiic_irq_dis(i2c, XIIC_INTR_BNB_MASK);
-
-		if (!i2c->tx_msg)
-			goto out;
-
-		if ((i2c->nmsgs == 1) && !i2c->rx_msg &&
-			xiic_tx_space(i2c) == 0)
-			xiic_wakeup(i2c, STATE_DONE);
-		else
-			xiic_wakeup(i2c, STATE_ERROR);
-	}
 	if (pend & (XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK)) {
 		/* Transmit register/FIFO is empty or ½ empty */
 
@@ -481,7 +705,10 @@
 			goto out;
 		}
 
-		xiic_fill_tx_fifo(i2c);
+		if (i2c->dynamic)
+			xiic_fill_tx_fifo(i2c);
+		else
+			xiic_send_tx(i2c);
 
 		/* current message sent and there is space in the fifo */
 		if (!xiic_tx_space(i2c) && xiic_tx_fifo_space(i2c) >= 2) {
@@ -491,7 +718,7 @@
 			if (i2c->nmsgs > 1) {
 				i2c->nmsgs--;
 				i2c->tx_msg++;
-				__xiic_start_xfer(i2c);
+				xfer_more = 1;
 			} else {
 				xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK);
 
@@ -505,10 +732,43 @@
 			 */
 			xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK);
 	}
+
+	if (pend & XIIC_INTR_BNB_MASK) {
+		/* IIC bus has transitioned to not busy */
+		clr |= XIIC_INTR_BNB_MASK;
+
+		/* The bus is not busy, disable BusNotBusy interrupt */
+		xiic_irq_dis(i2c, XIIC_INTR_BNB_MASK);
+
+		if (i2c->tx_msg && i2c->smbus_block_read) {
+			i2c->smbus_block_read = false;
+			/* Set requested message len=1 to indicate STATE_DONE */
+			i2c->tx_msg->len = 1;
+		}
+
+		if (!i2c->tx_msg)
+			goto out;
+
+		wakeup_req = 1;
+
+		if (i2c->nmsgs == 1 && !i2c->rx_msg &&
+		    xiic_tx_space(i2c) == 0)
+			wakeup_code = STATE_DONE;
+		else
+			wakeup_code = STATE_ERROR;
+	}
+
 out:
 	dev_dbg(i2c->adap.dev.parent, "%s clr: 0x%x\n", __func__, clr);
 
 	xiic_setreg32(i2c, XIIC_IISR_OFFSET, clr);
+	if (xfer_more)
+		__xiic_start_xfer(i2c);
+	if (wakeup_req)
+		xiic_wakeup(i2c, wakeup_code);
+
+	WARN_ON(xfer_more && wakeup_req);
+
 	mutex_unlock(&i2c->lock);
 	return IRQ_HANDLED;
 }
@@ -552,35 +812,114 @@
 
 static void xiic_start_recv(struct xiic_i2c *i2c)
 {
-	u8 rx_watermark;
+	u16 rx_watermark;
+	u8 cr = 0, rfd_set = 0;
 	struct i2c_msg *msg = i2c->rx_msg = i2c->tx_msg;
-	unsigned long flags;
 
-	/* Clear and enable Rx full interrupt. */
-	xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK | XIIC_INTR_TX_ERROR_MASK);
+	dev_dbg(i2c->adap.dev.parent, "%s entry, ISR: 0x%x, CR: 0x%x\n",
+		__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
+		xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
 
-	/* we want to get all but last byte, because the TX_ERROR IRQ is used
-	 * to inidicate error ACK on the address, and negative ack on the last
-	 * received byte, so to not mix them receive all but last.
-	 * In the case where there is only one byte to receive
-	 * we can check if ERROR and RX full is set at the same time
-	 */
-	rx_watermark = msg->len;
-	if (rx_watermark > IIC_RX_FIFO_DEPTH)
-		rx_watermark = IIC_RX_FIFO_DEPTH;
-	xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rx_watermark - 1);
-
-	local_irq_save(flags);
-	if (!(msg->flags & I2C_M_NOSTART))
-		/* write the address */
+	/* Disable Tx interrupts */
+	xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK | XIIC_INTR_TX_EMPTY_MASK);
+
+	if (i2c->dynamic) {
+		u8 bytes;
+		u16 val;
+
+		/* Clear and enable Rx full interrupt. */
+		xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK |
+				XIIC_INTR_TX_ERROR_MASK);
+
+		/*
+		 * We want to get all but last byte, because the TX_ERROR IRQ
+		 * is used to indicate error ACK on the address, and
+		 * negative ack on the last received byte, so to not mix
+		 * them receive all but last.
+		 * In the case where there is only one byte to receive
+		 * we can check if ERROR and RX full is set at the same time
+		 */
+		rx_watermark = msg->len;
+		bytes = min_t(u8, rx_watermark, IIC_RX_FIFO_DEPTH);
+		bytes--;
+
+		xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
+
+		if (!(msg->flags & I2C_M_NOSTART))
+			/* write the address */
+			xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
+				      i2c_8bit_addr_from_msg(msg) |
+				      XIIC_TX_DYN_START_MASK);
+
+		/* If last message, include dynamic stop bit with length */
+		val = (i2c->nmsgs == 1) ? XIIC_TX_DYN_STOP_MASK : 0;
+		val |= msg->len;
+
+		xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, val);
+
+		xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+	} else {
+		/*
+		 * If previous message is Tx, make sure that Tx FIFO is empty
+		 * before starting a new transfer as the repeated start in
+		 * standard mode can corrupt the transaction if there are
+		 * still bytes to be transmitted in FIFO
+		 */
+		if (i2c->prev_msg_tx) {
+			int status;
+
+			status = xiic_wait_tx_empty(i2c);
+			if (status)
+				return;
+		}
+
+		cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+
+		/* Set Receive fifo depth */
+		rx_watermark = msg->len;
+		if (rx_watermark > IIC_RX_FIFO_DEPTH) {
+			rfd_set = IIC_RX_FIFO_DEPTH - 1;
+		} else if ((rx_watermark == 1) || (rx_watermark == 0)) {
+			rfd_set = rx_watermark - 1;
+
+			/* Set No_ACK, except for smbus_block_read */
+			if (!(i2c->rx_msg->flags & I2C_M_RECV_LEN)) {
+				/* Handle single byte transfer separately */
+				cr |= XIIC_CR_NO_ACK_MASK;
+			}
+		} else {
+			rfd_set = rx_watermark - 2;
+		}
+
+		/* Check if RSTA should be set */
+		if (cr & XIIC_CR_MSMS_MASK) {
+			/* Already a master, RSTA should be set */
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
+				     XIIC_CR_REPEATED_START_MASK) &
+				     ~(XIIC_CR_DIR_IS_TX_MASK));
+		}
+
+		xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rfd_set);
+
+		/* Clear and enable Rx full and transmit complete interrupts */
+		xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK |
+				XIIC_INTR_TX_ERROR_MASK);
+
+		/* Write the address */
 		xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
-			i2c_8bit_addr_from_msg(msg) | XIIC_TX_DYN_START_MASK);
+			      i2c_8bit_addr_from_msg(msg));
 
-	xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+		/* Write to Control Register,to start transaction in Rx mode */
+		if ((cr & XIIC_CR_MSMS_MASK) == 0) {
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
+				     XIIC_CR_MSMS_MASK)
+				     & ~(XIIC_CR_DIR_IS_TX_MASK));
+		}
 
-	xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
-		msg->len | ((i2c->nmsgs == 1) ? XIIC_TX_DYN_STOP_MASK : 0));
-	local_irq_restore(flags);
+		dev_dbg(i2c->adap.dev.parent, "%s end, ISR: 0x%x, CR: 0x%x\n",
+			__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
+			xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
+	}
 
 	if (i2c->nmsgs == 1)
 		/* very last, enable bus not busy as well */
@@ -588,10 +927,17 @@
 
 	/* the message is tx:ed */
 	i2c->tx_pos = msg->len;
+
+	/* Enable interrupts */
+	xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK);
+
+	i2c->prev_msg_tx = false;
 }
 
 static void xiic_start_send(struct xiic_i2c *i2c)
 {
+	u8 cr = 0;
+	u16 data;
 	struct i2c_msg *msg = i2c->tx_msg;
 
 	xiic_irq_clr(i2c, XIIC_INTR_TX_ERROR_MASK);
@@ -602,22 +948,71 @@
 		__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
 		xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
 
-	if (!(msg->flags & I2C_M_NOSTART)) {
-		/* write the address */
-		u16 data = i2c_8bit_addr_from_msg(msg) |
-			XIIC_TX_DYN_START_MASK;
-		if ((i2c->nmsgs == 1) && msg->len == 0)
-			/* no data and last message -> add STOP */
-			data |= XIIC_TX_DYN_STOP_MASK;
+	if (i2c->dynamic) {
+		if (!(msg->flags & I2C_M_NOSTART)) {
+			/* write the address */
+			data = i2c_8bit_addr_from_msg(msg) |
+				XIIC_TX_DYN_START_MASK;
+
+			if (i2c->nmsgs == 1 && msg->len == 0)
+				/* no data and last message -> add STOP */
+				data |= XIIC_TX_DYN_STOP_MASK;
+
+			xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
+		}
+
+		xiic_fill_tx_fifo(i2c);
+
+		/* Clear any pending Tx empty, Tx Error and then enable them */
+		xiic_irq_clr_en(i2c, (XIIC_INTR_TX_EMPTY_MASK |
+				      XIIC_INTR_TX_ERROR_MASK |
+				      XIIC_INTR_BNB_MASK));
+	} else {
+		/*
+		 * If previous message is Tx, make sure that Tx FIFO is empty
+		 * before starting a new transfer as the repeated start in
+		 * standard mode can corrupt the transaction if there are
+		 * still bytes to be transmitted in FIFO
+		 */
+		if (i2c->prev_msg_tx) {
+			int status;
+
+			status = xiic_wait_tx_empty(i2c);
+			if (status)
+				return;
+		}
 
+		/* Check if RSTA should be set */
+		cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+		if (cr & XIIC_CR_MSMS_MASK) {
+			/* Already a master, RSTA should be set */
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
+				     XIIC_CR_REPEATED_START_MASK |
+				     XIIC_CR_DIR_IS_TX_MASK) &
+				     ~(XIIC_CR_NO_ACK_MASK));
+		}
+
+		/* Write address to FIFO */
+		data = i2c_8bit_addr_from_msg(msg);
 		xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
-	}
+		/* Fill fifo */
+		xiic_std_fill_tx_fifo(i2c);
 
-	xiic_fill_tx_fifo(i2c);
+		if ((cr & XIIC_CR_MSMS_MASK) == 0) {
 
-	/* Clear any pending Tx empty, Tx Error and then enable them. */
-	xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_ERROR_MASK |
-		XIIC_INTR_BNB_MASK);
+			/* Start Tx by writing to CR */
+			cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+			xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr |
+				     XIIC_CR_MSMS_MASK |
+				     XIIC_CR_DIR_IS_TX_MASK);
+		}
+
+		/* Clear any pending Tx empty, Tx Error and then enable them */
+		xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
+				XIIC_INTR_TX_ERROR_MASK |
+				XIIC_INTR_BNB_MASK);
+	}
+	i2c->prev_msg_tx = true;
 }
 
 static irqreturn_t xiic_isr(int irq, void *dev_id)
@@ -644,6 +1039,7 @@
 {
 	int first = 1;
 	int fifo_space = xiic_tx_fifo_space(i2c);
+
 	dev_dbg(i2c->adap.dev.parent, "%s entry, msg: %p, fifos space: %d\n",
 		__func__, i2c->tx_msg, fifo_space);
 
@@ -658,19 +1054,20 @@
 			i2c->nmsgs--;
 			i2c->tx_msg++;
 			i2c->tx_pos = 0;
-		} else
+		} else {
 			first = 0;
+		}
 
 		if (i2c->tx_msg->flags & I2C_M_RD) {
 			/* we dont date putting several reads in the FIFO */
 			xiic_start_recv(i2c);
 			return;
-		} else {
-			xiic_start_send(i2c);
-			if (xiic_tx_space(i2c) != 0) {
-				/* the message could not be completely sent */
-				break;
-			}
+		}
+
+		xiic_start_send(i2c);
+		if (xiic_tx_space(i2c) != 0) {
+			/* the message could not be completely sent */
+			break;
 		}
 
 		fifo_space = xiic_tx_fifo_space(i2c);
@@ -681,12 +1078,12 @@
 	 */
 	if (i2c->nmsgs > 1 || xiic_tx_space(i2c))
 		xiic_irq_clr_en(i2c, XIIC_INTR_TX_HALF_MASK);
-
 }
 
 static int xiic_start_xfer(struct xiic_i2c *i2c)
 {
 	int ret;
+
 	mutex_lock(&i2c->lock);
 
 	ret = xiic_reinit(i2c);
@@ -700,8 +1097,9 @@
 
 static int xiic_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
 {
+	bool broken_read, max_read_len, smbus_blk_read;
 	struct xiic_i2c *i2c = i2c_get_adapdata(adap);
-	int err;
+	int err, count;
 
 	dev_dbg(adap->dev.parent, "%s entry SR: 0x%x\n", __func__,
 		xiic_getreg8(i2c, XIIC_SR_REG_OFFSET));
@@ -717,14 +1115,42 @@
 	i2c->tx_msg = msgs;
 	i2c->nmsgs = num;
 
+	/* Decide standard mode or Dynamic mode */
+	i2c->dynamic = true;
+
+	/* Initialize prev message type */
+	i2c->prev_msg_tx = false;
+
+	/*
+	 * Scan through nmsgs, use dynamic mode when none of the below three
+	 * conditions occur. We need standard mode even if one condition holds
+	 * true in the entire array of messages in a single transfer.
+	 * If read transaction as dynamic mode is broken for delayed reads
+	 * in xlnx,axi-iic-2.0 / xlnx,xps-iic-2.00.a IP versions.
+	 * If read length is > 255 bytes.
+	 * If smbus_block_read transaction.
+	 */
+	for (count = 0; count < i2c->nmsgs; count++) {
+		broken_read = (i2c->quirks & DYNAMIC_MODE_READ_BROKEN_BIT) &&
+			       (i2c->tx_msg[count].flags & I2C_M_RD);
+		max_read_len = (i2c->tx_msg[count].flags & I2C_M_RD) &&
+				(i2c->tx_msg[count].len > MAX_READ_LENGTH_DYNAMIC);
+		smbus_blk_read = (i2c->tx_msg[count].flags & I2C_M_RECV_LEN);
+
+		if (broken_read || max_read_len || smbus_blk_read) {
+			i2c->dynamic = false;
+			break;
+		}
+	}
+
 	err = xiic_start_xfer(i2c);
 	if (err < 0) {
 		dev_err(adap->dev.parent, "Error xiic_start_xfer\n");
 		goto out;
 	}
 
-	if (wait_event_timeout(i2c->wait, (i2c->state == STATE_ERROR) ||
-		(i2c->state == STATE_DONE), HZ)) {
+	if (wait_event_timeout(i2c->wait, i2c->state == STATE_ERROR ||
+			       i2c->state == STATE_DONE, HZ)) {
 		err = (i2c->state == STATE_DONE) ? num : -EIO;
 		goto out;
 	} else {
@@ -742,7 +1168,7 @@
 
 static u32 xiic_func(struct i2c_adapter *adap)
 {
-	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA;
 }
 
 static const struct i2c_algorithm xiic_algorithm = {
@@ -750,23 +1176,129 @@
 	.functionality = xiic_func,
 };
 
-static const struct i2c_adapter_quirks xiic_quirks = {
-	.max_read_len = 255,
-};
-
 static const struct i2c_adapter xiic_adapter = {
 	.owner = THIS_MODULE,
-	.name = DRIVER_NAME,
 	.class = I2C_CLASS_DEPRECATED,
 	.algo = &xiic_algorithm,
-	.quirks = &xiic_quirks,
 };
 
+static const struct xiic_version_data xiic_2_00 = {
+	.quirks = DYNAMIC_MODE_READ_BROKEN_BIT,
+};
+
+#if defined(CONFIG_OF)
+static const struct of_device_id xiic_of_match[] = {
+	{ .compatible = "xlnx,xps-iic-2.00.a", .data = &xiic_2_00 },
+	{ .compatible = "xlnx,axi-iic-2.1", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xiic_of_match);
+#endif
+
+enum i2c_scl_freq {
+	REG_VALUES_100KHZ = 0,
+	REG_VALUES_400KHZ = 1,
+	REG_VALUES_1MHZ = 2
+};
+
+/* Reg values in ns derived from I2C spec and AXI I2C PG for different frequencies */
+static const struct timing_regs timing_reg_values[] = {
+	{ 5700, 5000, 4300, 550, 5000 }, /* Reg values for 100KHz */
+	{ 900, 900, 900, 400, 1600 },    /* Reg values for 400KHz */
+	{ 380, 380, 380, 170, 620 },     /* Reg values for 1MHz   */
+};
+
+/**
+ * xiic_setclk - Sets the configured clock rate
+ * @i2c: Pointer to the xiic device structure
+ *
+ * The timing register values are calculated according to the input clock
+ * frequency and configured scl frequency. For details, please refer the
+ * AXI I2C PG and NXP I2C Spec.
+ * Supported frequencies are 100KHz, 400KHz and 1MHz.
+ *
+ * Return: 0 on success (Supported frequency selected or not configurable in SW)
+ *	   -EINVAL on failure (scl frequency not supported or THIGH is 0)
+ */
+static int xiic_setclk(struct xiic_i2c *i2c)
+{
+	unsigned int clk_in_mhz;
+	unsigned int index = 0;
+	u32 reg_val;
+
+	dev_dbg(i2c->adap.dev.parent,
+		"%s entry, i2c->input_clk: %ld, i2c->i2c_clk: %d\n",
+		__func__, i2c->input_clk, i2c->i2c_clk);
+
+	/* If not specified in DT, do not configure in SW. Rely only on Vivado design */
+	if (!i2c->i2c_clk)
+		return 0;
+
+	clk_in_mhz = DIV_ROUND_UP(i2c->input_clk, 1000000);
+
+	switch (i2c->i2c_clk) {
+	case I2C_MAX_FAST_MODE_PLUS_FREQ:
+		index = REG_VALUES_1MHZ;
+		break;
+	case I2C_MAX_FAST_MODE_FREQ:
+		index = REG_VALUES_400KHZ;
+		break;
+	case I2C_MAX_STANDARD_MODE_FREQ:
+		index = REG_VALUES_100KHZ;
+		break;
+	default:
+		dev_warn(i2c->adap.dev.parent, "Unsupported scl frequency\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Value to be stored in a register is the number of clock cycles required
+	 * for the time duration. So the time is divided by the input clock time
+	 * period to get the number of clock cycles required. Refer Xilinx AXI I2C
+	 * PG document and I2C specification for further details.
+	 */
+
+	/* THIGH - Depends on SCL clock frequency(i2c_clk) as below */
+	reg_val = (DIV_ROUND_UP(i2c->input_clk, 2 * i2c->i2c_clk)) - 7;
+	if (reg_val == 0)
+		return -EINVAL;
+
+	xiic_setreg32(i2c, XIIC_THIGH_REG_OFFSET, reg_val - 1);
+
+	/* TLOW - Value same as THIGH */
+	xiic_setreg32(i2c, XIIC_TLOW_REG_OFFSET, reg_val - 1);
+
+	/* TSUSTA */
+	reg_val = (timing_reg_values[index].tsusta * clk_in_mhz) / 1000;
+	xiic_setreg32(i2c, XIIC_TSUSTA_REG_OFFSET, reg_val - 1);
+
+	/* TSUSTO */
+	reg_val = (timing_reg_values[index].tsusto * clk_in_mhz) / 1000;
+	xiic_setreg32(i2c, XIIC_TSUSTO_REG_OFFSET, reg_val - 1);
+
+	/* THDSTA */
+	reg_val = (timing_reg_values[index].thdsta * clk_in_mhz) / 1000;
+	xiic_setreg32(i2c, XIIC_THDSTA_REG_OFFSET, reg_val - 1);
+
+	/* TSUDAT */
+	reg_val = (timing_reg_values[index].tsudat * clk_in_mhz) / 1000;
+	xiic_setreg32(i2c, XIIC_TSUDAT_REG_OFFSET, reg_val - 1);
+
+	/* TBUF */
+	reg_val = (timing_reg_values[index].tbuf * clk_in_mhz) / 1000;
+	xiic_setreg32(i2c, XIIC_TBUF_REG_OFFSET, reg_val - 1);
+
+	/* THDDAT */
+	xiic_setreg32(i2c, XIIC_THDDAT_REG_OFFSET, 1);
+
+	return 0;
+}
 
 static int xiic_i2c_probe(struct platform_device *pdev)
 {
 	struct xiic_i2c *i2c;
 	struct xiic_i2c_platform_data *pdata;
+	const struct of_device_id *match;
 	struct resource *res;
 	int ret, irq;
 	u8 i;
@@ -776,6 +1308,13 @@
 	if (!i2c)
 		return -ENOMEM;
 
+	match = of_match_node(xiic_of_match, pdev->dev.of_node);
+	if (match && match->data) {
+		const struct xiic_version_data *data = match->data;
+
+		i2c->quirks = data->quirks;
+	}
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	i2c->base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(i2c->base))
@@ -793,6 +1332,8 @@
 	i2c_set_adapdata(&i2c->adap, i2c);
 	i2c->adap.dev.parent = &pdev->dev;
 	i2c->adap.dev.of_node = pdev->dev.of_node;
+	snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+		 DRIVER_NAME " %s", pdev->name);
 
 	mutex_init(&i2c->lock);
 	init_waitqueue_head(&i2c->wait);
@@ -812,6 +1353,15 @@
 	pm_runtime_use_autosuspend(i2c->dev);
 	pm_runtime_set_active(i2c->dev);
 	pm_runtime_enable(i2c->dev);
+
+	/* SCL frequency configuration */
+	i2c->input_clk = clk_get_rate(i2c->clk);
+	ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
+				   &i2c->i2c_clk);
+	/* If clock-frequency not specified in DT, do not configure in SW */
+	if (ret || i2c->i2c_clk > I2C_MAX_FAST_MODE_PLUS_FREQ)
+		i2c->i2c_clk = 0;
+
 	ret = devm_request_threaded_irq(&pdev->dev, irq, xiic_isr,
 					xiic_process, IRQF_ONESHOT,
 					pdev->name, i2c);
@@ -855,6 +1405,9 @@
 			i2c_new_client_device(&i2c->adap, pdata->devices + i);
 	}
 
+	dev_dbg(&pdev->dev, "mmio %08lx irq %d scl clock frequency %d\n",
+		(unsigned long)res->start, irq, i2c->i2c_clk);
+
 	return 0;
 
 err_clk_dis:
@@ -886,14 +1439,6 @@
 	return 0;
 }
 
-#if defined(CONFIG_OF)
-static const struct of_device_id xiic_of_match[] = {
-	{ .compatible = "xlnx,xps-iic-2.00.a", },
-	{},
-};
-MODULE_DEVICE_TABLE(of, xiic_of_match);
-#endif
-
 static int __maybe_unused xiic_i2c_runtime_suspend(struct device *dev)
 {
 	struct xiic_i2c *i2c = dev_get_drvdata(dev);
@@ -921,6 +1466,7 @@
 	SET_RUNTIME_PM_OPS(xiic_i2c_runtime_suspend,
 			   xiic_i2c_runtime_resume, NULL)
 };
+
 static struct platform_driver xiic_i2c_driver = {
 	.probe   = xiic_i2c_probe,
 	.remove  = xiic_i2c_remove,
@@ -933,7 +1479,7 @@
 
 module_platform_driver(xiic_i2c_driver);
 
+MODULE_ALIAS("platform:" DRIVER_NAME);
 MODULE_AUTHOR("info@mocean-labs.com");
 MODULE_DESCRIPTION("Xilinx I2C bus driver");
 MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:"DRIVER_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/busses/i2c-xlr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/busses/i2c-xlr.c
@@ -431,11 +431,15 @@
 	i2c_set_adapdata(&priv->adap, priv);
 	ret = i2c_add_numbered_adapter(&priv->adap);
 	if (ret < 0)
-		return ret;
+		goto err_unprepare_clk;
 
 	platform_set_drvdata(pdev, priv);
 	dev_info(&priv->adap.dev, "Added I2C Bus.\n");
 	return 0;
+
+err_unprepare_clk:
+	clk_unprepare(clk);
+	return ret;
 }
 
 static int xlr_i2c_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-core-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-core-acpi.c
@@ -327,6 +327,25 @@
 	{}
 };
 
+static const struct acpi_device_id i2c_acpi_force_100khz_device_ids[] = {
+	/*
+	 * When a 400KHz freq is used on this model of ELAN touchpad in Linux,
+	 * excessive smoothing (similar to when the touchpad's firmware detects
+	 * a noisy signal) is sometimes applied. As some devices' (e.g, Lenovo
+	 * V15 G4) ACPI tables specify a 400KHz frequency for this device and
+	 * some I2C busses (e.g, Designware I2C) default to a 400KHz freq,
+	 * force the speed to 100KHz as a workaround.
+	 *
+	 * For future investigation: This problem may be related to the default
+	 * HCNT/LCNT values given by some busses' drivers, because they are not
+	 * specified in the aforementioned devices' ACPI tables, and because
+	 * the device works without issues on Windows at what is expected to be
+	 * a 400KHz frequency. The root cause of the issue is not known.
+	 */
+	{ "ELAN06FA", 0 },
+	{}
+};
+
 static acpi_status i2c_acpi_lookup_speed(acpi_handle handle, u32 level,
 					   void *data, void **return_value)
 {
@@ -348,6 +367,9 @@
 	if (acpi_match_device_ids(adev, i2c_acpi_force_400khz_device_ids) == 0)
 		lookup->force_speed = I2C_MAX_FAST_MODE_FREQ;
 
+	if (acpi_match_device_ids(adev, i2c_acpi_force_100khz_device_ids) == 0)
+		lookup->force_speed = I2C_MAX_STANDARD_MODE_FREQ;
+
 	return AE_OK;
 }
 
@@ -421,18 +443,12 @@
 
 static struct i2c_client *i2c_acpi_find_client_by_adev(struct acpi_device *adev)
 {
-	struct device *dev;
-	struct i2c_client *client;
-
-	dev = bus_find_device_by_acpi_dev(&i2c_bus_type, adev);
-	if (!dev)
-		return NULL;
-
-	client = i2c_verify_client(dev);
-	if (!client)
-		put_device(dev);
+	return i2c_find_device_by_fwnode(acpi_fwnode_handle(adev));
+}
 
-	return client;
+static struct i2c_adapter *i2c_acpi_find_adapter_by_adev(struct acpi_device *adev)
+{
+	return i2c_find_adapter_by_fwnode(acpi_fwnode_handle(adev));
 }
 
 static int i2c_acpi_notify(struct notifier_block *nb, unsigned long value,
@@ -461,11 +477,17 @@
 			break;
 
 		client = i2c_acpi_find_client_by_adev(adev);
-		if (!client)
-			break;
+		if (client) {
+			i2c_unregister_device(client);
+			put_device(&client->dev);
+		}
+
+		adapter = i2c_acpi_find_adapter_by_adev(adev);
+		if (adapter) {
+			acpi_unbind_one(&adapter->dev);
+			put_device(&adapter->dev);
+		}
 
-		i2c_unregister_device(client);
-		put_device(&client->dev);
 		break;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-core-base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-core-base.c
@@ -16,6 +16,7 @@
 #include <linux/acpi.h>
 #include <linux/clk/clk-conf.h>
 #include <linux/completion.h>
+#include <linux/debugfs.h>
 #include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/errno.h>
@@ -66,6 +67,8 @@
 static DEFINE_STATIC_KEY_FALSE(i2c_trace_msg_key);
 static bool is_registered;
 
+static struct dentry *i2c_debugfs_root;
+
 int i2c_transfer_trace_reg(void)
 {
 	static_branch_inc(&i2c_trace_msg_key);
@@ -113,6 +116,25 @@
 }
 EXPORT_SYMBOL_GPL(i2c_match_id);
 
+const void *i2c_get_match_data(const struct i2c_client *client)
+{
+	struct i2c_driver *driver = to_i2c_driver(client->dev.driver);
+	const struct i2c_device_id *match;
+	const void *data;
+
+	data = device_get_match_data(&client->dev);
+	if (!data) {
+		match = i2c_match_id(driver->id_table, client);
+		if (!match)
+			return NULL;
+
+		data = (const void *)match->driver_data;
+	}
+
+	return data;
+}
+EXPORT_SYMBOL(i2c_get_match_data);
+
 static int i2c_device_match(struct device *dev, struct device_driver *drv)
 {
 	struct i2c_client	*client = i2c_verify_client(dev);
@@ -466,14 +488,12 @@
 static int i2c_device_probe(struct device *dev)
 {
 	struct i2c_client	*client = i2c_verify_client(dev);
-	struct i2c_adapter	*adap;
 	struct i2c_driver	*driver;
 	int status;
 
 	if (!client)
 		return 0;
 
-	adap = client->adapter;
 	client->irq = client->init_irq;
 
 	if (!client->irq) {
@@ -539,14 +559,6 @@
 
 	dev_dbg(dev, "probe\n");
 
-	if (adap->bus_regulator) {
-		status = regulator_enable(adap->bus_regulator);
-		if (status < 0) {
-			dev_err(&adap->dev, "Failed to enable bus regulator\n");
-			goto err_clear_wakeup_irq;
-		}
-	}
-
 	status = of_clk_set_defaults(dev->of_node, false);
 	if (status < 0)
 		goto err_clear_wakeup_irq;
@@ -604,10 +616,8 @@
 static void i2c_device_remove(struct device *dev)
 {
 	struct i2c_client	*client = to_i2c_client(dev);
-	struct i2c_adapter      *adap;
 	struct i2c_driver	*driver;
 
-	adap = client->adapter;
 	driver = to_i2c_driver(dev->driver);
 	if (driver->remove) {
 		int status;
@@ -622,8 +632,6 @@
 	devres_release_group(&client->dev, client->devres_group_id);
 
 	dev_pm_domain_detach(&client->dev, true);
-	if (!pm_runtime_status_suspended(&client->dev) && adap->bus_regulator)
-		regulator_disable(adap->bus_regulator);
 
 	dev_pm_clear_wake_irq(&client->dev);
 	device_init_wakeup(&client->dev, false);
@@ -633,86 +641,6 @@
 		pm_runtime_put(&client->adapter->dev);
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int i2c_resume_early(struct device *dev)
-{
-	struct i2c_client *client = i2c_verify_client(dev);
-	int err;
-
-	if (!client)
-		return 0;
-
-	if (pm_runtime_status_suspended(&client->dev) &&
-		client->adapter->bus_regulator) {
-		err = regulator_enable(client->adapter->bus_regulator);
-		if (err)
-			return err;
-	}
-
-	return pm_generic_resume_early(&client->dev);
-}
-
-static int i2c_suspend_late(struct device *dev)
-{
-	struct i2c_client *client = i2c_verify_client(dev);
-	int err;
-
-	if (!client)
-		return 0;
-
-	err = pm_generic_suspend_late(&client->dev);
-	if (err)
-		return err;
-
-	if (!pm_runtime_status_suspended(&client->dev) &&
-		client->adapter->bus_regulator)
-		return regulator_disable(client->adapter->bus_regulator);
-
-	return 0;
-}
-#endif
-
-#ifdef CONFIG_PM
-static int i2c_runtime_resume(struct device *dev)
-{
-	struct i2c_client *client = i2c_verify_client(dev);
-	int err;
-
-	if (!client)
-		return 0;
-
-	if (client->adapter->bus_regulator) {
-		err = regulator_enable(client->adapter->bus_regulator);
-		if (err)
-			return err;
-	}
-
-	return pm_generic_runtime_resume(&client->dev);
-}
-
-static int i2c_runtime_suspend(struct device *dev)
-{
-	struct i2c_client *client = i2c_verify_client(dev);
-	int err;
-
-	if (!client)
-		return 0;
-
-	err = pm_generic_runtime_suspend(&client->dev);
-	if (err)
-		return err;
-
-	if (client->adapter->bus_regulator)
-		return regulator_disable(client->adapter->bus_regulator);
-	return 0;
-}
-#endif
-
-static const struct dev_pm_ops i2c_device_pm = {
-	SET_LATE_SYSTEM_SLEEP_PM_OPS(i2c_suspend_late, i2c_resume_early)
-	SET_RUNTIME_PM_OPS(i2c_runtime_suspend, i2c_runtime_resume, NULL)
-};
-
 static void i2c_device_shutdown(struct device *dev)
 {
 	struct i2c_client *client = i2c_verify_client(dev);
@@ -772,7 +700,6 @@
 	.probe		= i2c_device_probe,
 	.remove		= i2c_device_remove,
 	.shutdown	= i2c_device_shutdown,
-	.pm		= &i2c_device_pm,
 };
 EXPORT_SYMBOL_GPL(i2c_bus_type);
 
@@ -990,6 +917,27 @@
 	return 0;
 }
 
+/*
+ * Serialize device instantiation in case it can be instantiated explicitly
+ * and by auto-detection
+ */
+static int i2c_lock_addr(struct i2c_adapter *adap, unsigned short addr,
+			 unsigned short flags)
+{
+	if (!(flags & I2C_CLIENT_TEN) &&
+	    test_and_set_bit(addr, adap->addrs_in_instantiation))
+		return -EBUSY;
+
+	return 0;
+}
+
+static void i2c_unlock_addr(struct i2c_adapter *adap, unsigned short addr,
+			    unsigned short flags)
+{
+	if (!(flags & I2C_CLIENT_TEN))
+		clear_bit(addr, adap->addrs_in_instantiation);
+}
+
 /**
  * i2c_new_client_device - instantiate an i2c device
  * @adap: the adapter managing the device
@@ -1036,6 +984,10 @@
 		goto out_err_silent;
 	}
 
+	status = i2c_lock_addr(adap, client->addr, client->flags);
+	if (status)
+		goto out_err_silent;
+
 	/* Check for address business */
 	status = i2c_check_addr_busy(adap, i2c_encode_flags_to_addr(client));
 	if (status)
@@ -1066,6 +1018,8 @@
 	dev_dbg(&adap->dev, "client [%s] registered with bus id %s\n",
 		client->name, dev_name(&client->dev));
 
+	i2c_unlock_addr(adap, client->addr, client->flags);
+
 	return client;
 
 out_remove_swnode:
@@ -1076,6 +1030,7 @@
 	dev_err(&adap->dev,
 		"Failed to register i2c client %s at 0x%02x (%d)\n",
 		client->name, client->addr, status);
+	i2c_unlock_addr(adap, client->addr, client->flags);
 out_err_silent:
 	kfree(client);
 	return ERR_PTR(status);
@@ -1104,9 +1059,39 @@
 }
 EXPORT_SYMBOL_GPL(i2c_unregister_device);
 
+/**
+ * i2c_find_device_by_fwnode() - find an i2c_client for the fwnode
+ * @fwnode: &struct fwnode_handle corresponding to the &struct i2c_client
+ *
+ * Look up and return the &struct i2c_client corresponding to the @fwnode.
+ * If no client can be found, or @fwnode is NULL, this returns NULL.
+ *
+ * The user must call put_device(&client->dev) once done with the i2c client.
+ */
+struct i2c_client *i2c_find_device_by_fwnode(struct fwnode_handle *fwnode)
+{
+	struct i2c_client *client;
+	struct device *dev;
+
+	if (!fwnode)
+		return NULL;
+
+	dev = bus_find_device_by_fwnode(&i2c_bus_type, fwnode);
+	if (!dev)
+		return NULL;
+
+	client = i2c_verify_client(dev);
+	if (!client)
+		put_device(dev);
+
+	return client;
+}
+EXPORT_SYMBOL(i2c_find_device_by_fwnode);
+
 
 static const struct i2c_device_id dummy_id[] = {
 	{ "dummy", 0 },
+	{ "smbus_host_notify", 0 },
 	{ },
 };
 
@@ -1572,7 +1557,9 @@
 		goto out_list;
 	}
 
-	res = of_i2c_setup_smbus_alert(adap);
+	adap->debugfs = debugfs_create_dir(dev_name(&adap->dev), i2c_debugfs_root);
+
+	res = i2c_setup_smbus_alert(adap);
 	if (res)
 		goto out_reg;
 
@@ -1610,6 +1597,7 @@
 	return 0;
 
 out_reg:
+	debugfs_remove_recursive(adap->debugfs);
 	init_completion(&adap->dev_released);
 	device_unregister(&adap->dev);
 	wait_for_completion(&adap->dev_released);
@@ -1811,6 +1799,8 @@
 
 	i2c_host_notify_irq_teardown(adap);
 
+	debugfs_remove_recursive(adap->debugfs);
+
 	/* wait until all references to the device are gone
 	 *
 	 * FIXME: This is old code and should ideally be replaced by an
@@ -1859,6 +1849,75 @@
 }
 EXPORT_SYMBOL_GPL(devm_i2c_add_adapter);
 
+static int i2c_dev_or_parent_fwnode_match(struct device *dev, const void *data)
+{
+	if (dev_fwnode(dev) == data)
+		return 1;
+
+	if (dev->parent && dev_fwnode(dev->parent) == data)
+		return 1;
+
+	return 0;
+}
+
+/**
+ * i2c_find_adapter_by_fwnode() - find an i2c_adapter for the fwnode
+ * @fwnode: &struct fwnode_handle corresponding to the &struct i2c_adapter
+ *
+ * Look up and return the &struct i2c_adapter corresponding to the @fwnode.
+ * If no adapter can be found, or @fwnode is NULL, this returns NULL.
+ *
+ * The user must call put_device(&adapter->dev) once done with the i2c adapter.
+ */
+struct i2c_adapter *i2c_find_adapter_by_fwnode(struct fwnode_handle *fwnode)
+{
+	struct i2c_adapter *adapter;
+	struct device *dev;
+
+	if (!fwnode)
+		return NULL;
+
+	dev = bus_find_device(&i2c_bus_type, NULL, fwnode,
+			      i2c_dev_or_parent_fwnode_match);
+	if (!dev)
+		return NULL;
+
+	adapter = i2c_verify_adapter(dev);
+	if (!adapter)
+		put_device(dev);
+
+	return adapter;
+}
+EXPORT_SYMBOL(i2c_find_adapter_by_fwnode);
+
+/**
+ * i2c_get_adapter_by_fwnode() - find an i2c_adapter for the fwnode
+ * @fwnode: &struct fwnode_handle corresponding to the &struct i2c_adapter
+ *
+ * Look up and return the &struct i2c_adapter corresponding to the @fwnode,
+ * and increment the adapter module's use count. If no adapter can be found,
+ * or @fwnode is NULL, this returns NULL.
+ *
+ * The user must call i2c_put_adapter(adapter) once done with the i2c adapter.
+ * Note that this is different from i2c_find_adapter_by_node().
+ */
+struct i2c_adapter *i2c_get_adapter_by_fwnode(struct fwnode_handle *fwnode)
+{
+	struct i2c_adapter *adapter;
+
+	adapter = i2c_find_adapter_by_fwnode(fwnode);
+	if (!adapter)
+		return NULL;
+
+	if (!try_module_get(adapter->owner)) {
+		put_device(&adapter->dev);
+		adapter = NULL;
+	}
+
+	return adapter;
+}
+EXPORT_SYMBOL(i2c_get_adapter_by_fwnode);
+
 static void i2c_parse_timing(struct device *dev, char *prop_name, u32 *cur_val_p,
 			    u32 def_val, bool use_def)
 {
@@ -2039,6 +2098,8 @@
 
 	is_registered = true;
 
+	i2c_debugfs_root = debugfs_create_dir("i2c", NULL);
+
 #ifdef CONFIG_I2C_COMPAT
 	i2c_adapter_compat_class = class_compat_register("i2c-adapter");
 	if (!i2c_adapter_compat_class) {
@@ -2077,6 +2138,7 @@
 #ifdef CONFIG_I2C_COMPAT
 	class_compat_unregister(i2c_adapter_compat_class);
 #endif
+	debugfs_remove_recursive(i2c_debugfs_root);
 	bus_unregister(&i2c_bus_type);
 	tracepoint_synchronize_unregister();
 }
@@ -2167,13 +2229,18 @@
  * Returns negative errno, else the number of messages executed.
  *
  * Adapter lock must be held when calling this function. No debug logging
- * takes place. adap->algo->master_xfer existence isn't checked.
+ * takes place.
  */
 int __i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
 {
 	unsigned long orig_jiffies;
 	int ret, try;
 
+	if (!adap->algo->master_xfer) {
+		dev_dbg(&adap->dev, "I2C level transfers not supported\n");
+		return -EOPNOTSUPP;
+	}
+
 	if (WARN_ON(!msgs || num < 1))
 		return -EINVAL;
 
@@ -2240,11 +2307,6 @@
 {
 	int ret;
 
-	if (!adap->algo->master_xfer) {
-		dev_dbg(&adap->dev, "I2C level transfers not supported\n");
-		return -EOPNOTSUPP;
-	}
-
 	/* REVISIT the fault reporting model here is weak:
 	 *
 	 *  - When we get an error after receiving N bytes from a slave,
@@ -2559,8 +2621,9 @@
 	if (!adap)
 		return;
 
-	put_device(&adap->dev);
 	module_put(adap->owner);
+	/* Should be last, otherwise we risk use-after-free with 'adap' */
+	put_device(&adap->dev);
 }
 EXPORT_SYMBOL(i2c_put_adapter);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-core-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-core-of.c
@@ -113,72 +113,6 @@
 	of_node_put(bus);
 }
 
-static int of_dev_or_parent_node_match(struct device *dev, const void *data)
-{
-	if (dev->of_node == data)
-		return 1;
-
-	if (dev->parent)
-		return dev->parent->of_node == data;
-
-	return 0;
-}
-
-/* must call put_device() when done with returned i2c_client device */
-struct i2c_client *of_find_i2c_device_by_node(struct device_node *node)
-{
-	struct device *dev;
-	struct i2c_client *client;
-
-	dev = bus_find_device_by_of_node(&i2c_bus_type, node);
-	if (!dev)
-		return NULL;
-
-	client = i2c_verify_client(dev);
-	if (!client)
-		put_device(dev);
-
-	return client;
-}
-EXPORT_SYMBOL(of_find_i2c_device_by_node);
-
-/* must call put_device() when done with returned i2c_adapter device */
-struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node)
-{
-	struct device *dev;
-	struct i2c_adapter *adapter;
-
-	dev = bus_find_device(&i2c_bus_type, NULL, node,
-			      of_dev_or_parent_node_match);
-	if (!dev)
-		return NULL;
-
-	adapter = i2c_verify_adapter(dev);
-	if (!adapter)
-		put_device(dev);
-
-	return adapter;
-}
-EXPORT_SYMBOL(of_find_i2c_adapter_by_node);
-
-/* must call i2c_put_adapter() when done with returned i2c_adapter device */
-struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node)
-{
-	struct i2c_adapter *adapter;
-
-	adapter = of_find_i2c_adapter_by_node(node);
-	if (!adapter)
-		return NULL;
-
-	if (!try_module_get(adapter->owner)) {
-		put_device(&adapter->dev);
-		adapter = NULL;
-	}
-
-	return adapter;
-}
-EXPORT_SYMBOL(of_get_i2c_adapter_by_node);
-
 static const struct of_device_id*
 i2c_of_match_device_sysfs(const struct of_device_id *matches,
 				  struct i2c_client *client)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-core-smbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-core-smbus.c
@@ -14,6 +14,7 @@
 #include <linux/err.h>
 #include <linux/i2c.h>
 #include <linux/i2c-smbus.h>
+#include <linux/property.h>
 #include <linux/slab.h>
 
 #include "i2c-core.h"
@@ -701,13 +702,17 @@
 }
 EXPORT_SYMBOL_GPL(i2c_new_smbus_alert_device);
 
-#if IS_ENABLED(CONFIG_I2C_SMBUS) && IS_ENABLED(CONFIG_OF)
-int of_i2c_setup_smbus_alert(struct i2c_adapter *adapter)
+#if IS_ENABLED(CONFIG_I2C_SMBUS)
+int i2c_setup_smbus_alert(struct i2c_adapter *adapter)
 {
+	struct device *parent = adapter->dev.parent;
 	int irq;
 
-	irq = of_property_match_string(adapter->dev.of_node, "interrupt-names",
-				       "smbus_alert");
+	/* Adapter instantiated without parent, skip the SMBus alert setup */
+	if (!parent)
+		return 0;
+
+	irq = device_property_match_string(parent, "interrupt-names", "smbus_alert");
 	if (irq == -EINVAL || irq == -ENODATA)
 		return 0;
 	else if (irq < 0)
@@ -715,5 +720,5 @@
 
 	return PTR_ERR_OR_ZERO(i2c_new_smbus_alert_device(adapter, NULL));
 }
-EXPORT_SYMBOL_GPL(of_i2c_setup_smbus_alert);
+EXPORT_SYMBOL_GPL(i2c_setup_smbus_alert);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-core.h
@@ -3,6 +3,7 @@
  * i2c-core.h - interfaces internal to the I2C framework
  */
 
+#include <linux/kconfig.h>
 #include <linux/rwsem.h>
 
 struct i2c_devinfo {
@@ -29,7 +30,8 @@
  */
 static inline bool i2c_in_atomic_xfer_mode(void)
 {
-	return system_state > SYSTEM_RUNNING && irqs_disabled();
+	return system_state > SYSTEM_RUNNING &&
+	       (IS_ENABLED(CONFIG_PREEMPT_COUNT) ? !preemptible() : irqs_disabled());
 }
 
 static inline int __i2c_lock_bus_helper(struct i2c_adapter *adap)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-dev.c
@@ -450,8 +450,8 @@
 		if (rdwr_arg.nmsgs > I2C_RDWR_IOCTL_MAX_MSGS)
 			return -EINVAL;
 
-		rdwr_pa = memdup_user(rdwr_arg.msgs,
-				      rdwr_arg.nmsgs * sizeof(struct i2c_msg));
+		rdwr_pa = memdup_array_user(rdwr_arg.msgs,
+					    rdwr_arg.nmsgs, sizeof(struct i2c_msg));
 		if (IS_ERR(rdwr_pa))
 			return PTR_ERR(rdwr_pa);
 
@@ -535,6 +535,9 @@
 				   sizeof(rdwr_arg)))
 			return -EFAULT;
 
+		if (!rdwr_arg.msgs || rdwr_arg.nmsgs == 0)
+			return -EINVAL;
+
 		if (rdwr_arg.nmsgs > I2C_RDWR_IOCTL_MAX_MSGS)
 			return -EINVAL;
 
@@ -665,16 +668,21 @@
 	i2c_dev->dev.class = i2c_dev_class;
 	i2c_dev->dev.parent = &adap->dev;
 	i2c_dev->dev.release = i2cdev_dev_release;
-	dev_set_name(&i2c_dev->dev, "i2c-%d", adap->nr);
+
+	res = dev_set_name(&i2c_dev->dev, "i2c-%d", adap->nr);
+	if (res)
+		goto err_put_i2c_dev;
 
 	res = cdev_device_add(&i2c_dev->cdev, &i2c_dev->dev);
-	if (res) {
-		put_i2c_dev(i2c_dev, false);
-		return res;
-	}
+	if (res)
+		goto err_put_i2c_dev;
 
 	pr_debug("adapter [%s] registered as minor %d\n", adap->name, adap->nr);
 	return 0;
+
+err_put_i2c_dev:
+	put_i2c_dev(i2c_dev, false);
+	return res;
 }
 
 static int i2cdev_detach_adapter(struct device *dev, void *dummy)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-mux.c
@@ -340,7 +340,7 @@
 		priv->adap.lock_ops = &i2c_parent_lock_ops;
 
 	/* Sanity check on class */
-	if (i2c_mux_parent_classes(parent) & class)
+	if (i2c_mux_parent_classes(parent) & class & ~I2C_CLASS_DEPRECATED)
 		dev_err(&parent->dev,
 			"Segment %d behind mux can't share classes with ancestors\n",
 			chan_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-slave-testunit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-slave-testunit.c
@@ -118,9 +118,19 @@
 			queue_delayed_work(system_long_wq, &tu->worker,
 					   msecs_to_jiffies(10 * tu->regs[TU_REG_DELAY]));
 		}
-		fallthrough;
+
+		/*
+		 * Reset reg_idx to avoid that work gets queued again in case of
+		 * STOP after a following read message. But do not clear TU regs
+		 * here because we still need them in the workqueue!
+		 */
+		tu->reg_idx = 0;
+		break;
 
 	case I2C_SLAVE_WRITE_REQUESTED:
+		if (test_bit(TU_FLAG_IN_PROCESS, &tu->flags))
+			return -EBUSY;
+
 		memset(tu->regs, 0, TU_NUM_REGS);
 		tu->reg_idx = 0;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/i2c-smbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/i2c-smbus.c
@@ -13,7 +13,7 @@
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/of_irq.h>
+#include <linux/property.h>
 #include <linux/slab.h>
 #include <linux/workqueue.h>
 
@@ -34,6 +34,7 @@
 	struct i2c_client *client = i2c_verify_client(dev);
 	struct alert_data *data = addrp;
 	struct i2c_driver *driver;
+	int ret;
 
 	if (!client || client->addr != data->addr)
 		return 0;
@@ -47,16 +48,47 @@
 	device_lock(dev);
 	if (client->dev.driver) {
 		driver = to_i2c_driver(client->dev.driver);
-		if (driver->alert)
+		if (driver->alert) {
+			/* Stop iterating after we find the device */
 			driver->alert(client, data->type, data->data);
-		else
+			ret = -EBUSY;
+		} else {
 			dev_warn(&client->dev, "no driver alert()!\n");
-	} else
+			ret = -EOPNOTSUPP;
+		}
+	} else {
 		dev_dbg(&client->dev, "alert with no driver\n");
+		ret = -ENODEV;
+	}
 	device_unlock(dev);
 
-	/* Stop iterating after we find the device */
-	return -EBUSY;
+	return ret;
+}
+
+/* Same as above, but call back all drivers with alert handler */
+
+static int smbus_do_alert_force(struct device *dev, void *addrp)
+{
+	struct i2c_client *client = i2c_verify_client(dev);
+	struct alert_data *data = addrp;
+	struct i2c_driver *driver;
+
+	if (!client || (client->flags & I2C_CLIENT_TEN))
+		return 0;
+
+	/*
+	 * Drivers should either disable alerts, or provide at least
+	 * a minimal handler. Lock so the driver won't change.
+	 */
+	device_lock(dev);
+	if (client->dev.driver) {
+		driver = to_i2c_driver(client->dev.driver);
+		if (driver->alert)
+			driver->alert(client, data->type, data->data);
+	}
+	device_unlock(dev);
+
+	return 0;
 }
 
 /*
@@ -67,6 +99,7 @@
 {
 	struct i2c_smbus_alert *alert = d;
 	struct i2c_client *ara;
+	unsigned short prev_addr = I2C_CLIENT_END; /* Not a valid address */
 
 	ara = alert->ara;
 
@@ -94,8 +127,25 @@
 			data.addr, data.data);
 
 		/* Notify driver for the device which issued the alert */
-		device_for_each_child(&ara->adapter->dev, &data,
-				      smbus_do_alert);
+		status = device_for_each_child(&ara->adapter->dev, &data,
+					       smbus_do_alert);
+		/*
+		 * If we read the same address more than once, and the alert
+		 * was not handled by a driver, it won't do any good to repeat
+		 * the loop because it will never terminate. Try again, this
+		 * time calling the alert handlers of all devices connected to
+		 * the bus, and abort the loop afterwards. If this helps, we
+		 * are all set. If it doesn't, there is nothing else we can do,
+		 * so we might as well abort the loop.
+		 * Note: This assumes that a driver with alert handler handles
+		 * the alert properly and clears it if necessary.
+		 */
+		if (data.addr == prev_addr && status != -EBUSY) {
+			device_for_each_child(&ara->adapter->dev, &data,
+					      smbus_do_alert_force);
+			break;
+		}
+		prev_addr = data.addr;
 	}
 
 	return IRQ_HANDLED;
@@ -128,7 +178,8 @@
 	if (setup) {
 		irq = setup->irq;
 	} else {
-		irq = of_irq_get_byname(adapter->dev.of_node, "smbus_alert");
+		irq = fwnode_irq_get_byname(dev_fwnode(adapter->dev.parent),
+					    "smbus_alert");
 		if (irq <= 0)
 			return irq;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/muxes/i2c-demux-pinctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/muxes/i2c-demux-pinctrl.c
@@ -61,7 +61,7 @@
 	if (ret)
 		goto err;
 
-	adap = of_find_i2c_adapter_by_node(priv->chan[new_chan].parent_np);
+	adap = of_get_i2c_adapter_by_node(priv->chan[new_chan].parent_np);
 	if (!adap) {
 		ret = -ENODEV;
 		goto err_with_revert;
@@ -243,6 +243,10 @@
 
 		props[i].name = devm_kstrdup(&pdev->dev, "status", GFP_KERNEL);
 		props[i].value = devm_kstrdup(&pdev->dev, "ok", GFP_KERNEL);
+		if (!props[i].name || !props[i].value) {
+			err = -ENOMEM;
+			goto err_rollback;
+		}
 		props[i].length = 3;
 
 		of_changeset_init(&priv->chan[i].chgset);
@@ -257,11 +261,13 @@
 	pm_runtime_no_callbacks(&pdev->dev);
 
 	/* switch to first parent as active master */
-	i2c_demux_activate_master(priv, 0);
+	err = i2c_demux_activate_master(priv, 0);
+	if (err)
+		goto err_rollback;
 
 	err = device_create_file(&pdev->dev, &dev_attr_available_masters);
 	if (err)
-		goto err_rollback;
+		goto err_rollback_activation;
 
 	err = device_create_file(&pdev->dev, &dev_attr_current_master);
 	if (err)
@@ -271,8 +277,9 @@
 
 err_rollback_available:
 	device_remove_file(&pdev->dev, &dev_attr_available_masters);
-err_rollback:
+err_rollback_activation:
 	i2c_demux_deactivate_master(priv);
+err_rollback:
 	for (j = 0; j < i; j++) {
 		of_node_put(priv->chan[j].parent_np);
 		of_changeset_destroy(&priv->chan[j].chgset);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/muxes/i2c-mux-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/muxes/i2c-mux-gpio.c
@@ -49,45 +49,6 @@
 	return 0;
 }
 
-#ifdef CONFIG_ACPI
-
-static int i2c_mux_gpio_get_acpi_adr(struct device *dev,
-				     struct fwnode_handle *fwdev,
-				     unsigned int *adr)
-
-{
-	unsigned long long adr64;
-	acpi_status status;
-
-	status = acpi_evaluate_integer(ACPI_HANDLE_FWNODE(fwdev),
-				       METHOD_NAME__ADR,
-				       NULL, &adr64);
-
-	if (!ACPI_SUCCESS(status)) {
-		dev_err(dev, "Cannot get address\n");
-		return -EINVAL;
-	}
-
-	*adr = adr64;
-	if (*adr != adr64) {
-		dev_err(dev, "Address out of range\n");
-		return -ERANGE;
-	}
-
-	return 0;
-}
-
-#else
-
-static int i2c_mux_gpio_get_acpi_adr(struct device *dev,
-				     struct fwnode_handle *fwdev,
-				     unsigned int *adr)
-{
-	return -EINVAL;
-}
-
-#endif
-
 static int i2c_mux_gpio_probe_fw(struct gpiomux *mux,
 				 struct platform_device *pdev)
 {
@@ -141,9 +102,11 @@
 			fwnode_property_read_u32(child, "reg", values + i);
 
 		} else if (is_acpi_node(child)) {
-			rc = i2c_mux_gpio_get_acpi_adr(dev, child, values + i);
-			if (rc)
-				return rc;
+			rc = acpi_get_local_address(ACPI_HANDLE_FWNODE(child), values + i);
+			if (rc) {
+				fwnode_handle_put(child);
+				return dev_err_probe(dev, rc, "Cannot get address\n");
+			}
 		}
 
 		i++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/muxes/i2c-mux-gpmux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/muxes/i2c-mux-gpmux.c
@@ -52,7 +52,7 @@
 		dev_err(dev, "Cannot parse i2c-parent\n");
 		return ERR_PTR(-ENODEV);
 	}
-	parent = of_find_i2c_adapter_by_node(parent_np);
+	parent = of_get_i2c_adapter_by_node(parent_np);
 	of_node_put(parent_np);
 	if (!parent)
 		return ERR_PTR(-EPROBE_DEFER);
@@ -134,6 +134,7 @@
 	return 0;
 
 err_children:
+	of_node_put(child);
 	i2c_mux_del_adapters(muxc);
 err_parent:
 	i2c_put_adapter(parent);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -239,11 +239,9 @@
 	int ret = 0;
 
 	regval = pca954x_regval(data, chan);
-	/* Only select the channel if its different from the last channel */
-	if (data->last_chan != regval) {
-		ret = pca954x_reg_write(muxc->parent, client, regval);
-		data->last_chan = ret < 0 ? 0 : regval;
-	}
+
+	ret = pca954x_reg_write(muxc->parent, client, regval);
+	data->last_chan = ret < 0 ? 0 : regval;
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/muxes/i2c-mux-pinctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/muxes/i2c-mux-pinctrl.c
@@ -62,7 +62,7 @@
 		dev_err(dev, "Cannot parse i2c-parent\n");
 		return ERR_PTR(-ENODEV);
 	}
-	parent = of_find_i2c_adapter_by_node(parent_np);
+	parent = of_get_i2c_adapter_by_node(parent_np);
 	of_node_put(parent_np);
 	if (!parent)
 		return ERR_PTR(-EPROBE_DEFER);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i2c/muxes/i2c-mux-reg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i2c/muxes/i2c-mux-reg.c
@@ -183,13 +183,12 @@
 	if (!mux->data.reg) {
 		dev_info(&pdev->dev,
 			"Register not set, using platform resource\n");
-		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		mux->data.reg_size = resource_size(res);
-		mux->data.reg = devm_ioremap_resource(&pdev->dev, res);
+		mux->data.reg = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 		if (IS_ERR(mux->data.reg)) {
 			ret = PTR_ERR(mux->data.reg);
 			goto err_put_parent;
 		}
+		mux->data.reg_size = resource_size(res);
 	}
 
 	if (mux->data.reg_size != 4 && mux->data.reg_size != 2 &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i3c/master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i3c/master.c
@@ -279,7 +279,8 @@
 	struct i3c_device_info devinfo;
 	u16 manuf, part, ext;
 
-	i3c_device_get_info(i3cdev, &devinfo);
+	if (i3cdev->desc)
+		devinfo = i3cdev->desc->info;
 	manuf = I3C_PID_MANUF_ID(devinfo.pid);
 	part = I3C_PID_PART_ID(devinfo.pid);
 	ext = I3C_PID_EXTRA_INFO(devinfo.pid);
@@ -343,7 +344,8 @@
 static enum i3c_addr_slot_status
 i3c_bus_get_addr_slot_status(struct i3c_bus *bus, u16 addr)
 {
-	int status, bitpos = addr * 2;
+	unsigned long status;
+	int bitpos = addr * 2;
 
 	if (addr > I2C_MAX_ADDR)
 		return I3C_ADDR_SLOT_RSVD;
@@ -1281,7 +1283,7 @@
 					     I3C_ADDR_SLOT_FREE);
 
 	if (dev->boardinfo && dev->boardinfo->init_dyn_addr)
-		i3c_bus_set_addr_slot_status(&master->bus, dev->info.dyn_addr,
+		i3c_bus_set_addr_slot_status(&master->bus, dev->boardinfo->init_dyn_addr,
 					     I3C_ADDR_SLOT_FREE);
 }
 
@@ -1505,9 +1507,11 @@
 			desc->dev->dev.of_node = desc->boardinfo->of_node;
 
 		ret = device_register(&desc->dev->dev);
-		if (ret)
+		if (ret) {
 			dev_err(&master->dev,
 				"Failed to add I3C device (err = %d)\n", ret);
+			put_device(&desc->dev->dev);
+		}
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i3c/master/dw-i3c-master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i3c/master/dw-i3c-master.c
@@ -793,6 +793,10 @@
 		return -ENOMEM;
 
 	pos = dw_i3c_master_get_free_pos(master);
+	if (pos < 0) {
+		dw_i3c_master_free_xfer(xfer);
+		return pos;
+	}
 	cmd = &xfer->cmds[0];
 	cmd->cmd_hi = 0x1;
 	cmd->cmd_lo = COMMAND_PORT_DEV_COUNT(master->maxdevs - pos) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i3c/master/i3c-master-cdns.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i3c/master/i3c-master-cdns.c
@@ -77,7 +77,8 @@
 #define PRESCL_CTRL0			0x14
 #define PRESCL_CTRL0_I2C(x)		((x) << 16)
 #define PRESCL_CTRL0_I3C(x)		(x)
-#define PRESCL_CTRL0_MAX		GENMASK(9, 0)
+#define PRESCL_CTRL0_I3C_MAX		GENMASK(9, 0)
+#define PRESCL_CTRL0_I2C_MAX		GENMASK(15, 0)
 
 #define PRESCL_CTRL1			0x18
 #define PRESCL_CTRL1_PP_LOW_MASK	GENMASK(15, 8)
@@ -192,7 +193,7 @@
 #define SLV_STATUS1_HJ_DIS		BIT(18)
 #define SLV_STATUS1_MR_DIS		BIT(17)
 #define SLV_STATUS1_PROT_ERR		BIT(16)
-#define SLV_STATUS1_DA(x)		(((s) & GENMASK(15, 9)) >> 9)
+#define SLV_STATUS1_DA(s)		(((s) & GENMASK(15, 9)) >> 9)
 #define SLV_STATUS1_HAS_DA		BIT(8)
 #define SLV_STATUS1_DDR_RX_FULL		BIT(7)
 #define SLV_STATUS1_DDR_TX_FULL		BIT(6)
@@ -1234,7 +1235,7 @@
 		return -EINVAL;
 
 	pres = DIV_ROUND_UP(sysclk_rate, (bus->scl_rate.i3c * 4)) - 1;
-	if (pres > PRESCL_CTRL0_MAX)
+	if (pres > PRESCL_CTRL0_I3C_MAX)
 		return -ERANGE;
 
 	bus->scl_rate.i3c = sysclk_rate / ((pres + 1) * 4);
@@ -1247,7 +1248,7 @@
 	max_i2cfreq = bus->scl_rate.i2c;
 
 	pres = (sysclk_rate / (max_i2cfreq * 5)) - 1;
-	if (pres > PRESCL_CTRL0_MAX)
+	if (pres > PRESCL_CTRL0_I2C_MAX)
 		return -ERANGE;
 
 	bus->scl_rate.i2c = sysclk_rate / ((pres + 1) * 5);
@@ -1624,13 +1625,13 @@
 	/* Device ID0 is reserved to describe this master. */
 	master->maxdevs = CONF_STATUS0_DEVS_NUM(val);
 	master->free_rr_slots = GENMASK(master->maxdevs, 1);
+	master->caps.ibirfifodepth = CONF_STATUS0_IBIR_DEPTH(val);
+	master->caps.cmdrfifodepth = CONF_STATUS0_CMDR_DEPTH(val);
 
 	val = readl(master->regs + CONF_STATUS1);
 	master->caps.cmdfifodepth = CONF_STATUS1_CMD_DEPTH(val);
 	master->caps.rxfifodepth = CONF_STATUS1_RX_DEPTH(val);
 	master->caps.txfifodepth = CONF_STATUS1_TX_DEPTH(val);
-	master->caps.ibirfifodepth = CONF_STATUS0_IBIR_DEPTH(val);
-	master->caps.cmdrfifodepth = CONF_STATUS0_CMDR_DEPTH(val);
 
 	spin_lock_init(&master->ibi.lock);
 	master->ibi.num_slots = CONF_STATUS1_IBI_HW_RES(val);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i3c/master/mipi-i3c-hci/dat_v1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i3c/master/mipi-i3c-hci/dat_v1.c
@@ -64,15 +64,17 @@
 		return -EOPNOTSUPP;
 	}
 
-	/* use a bitmap for faster free slot search */
-	hci->DAT_data = bitmap_zalloc(hci->DAT_entries, GFP_KERNEL);
-	if (!hci->DAT_data)
-		return -ENOMEM;
-
-	/* clear them */
-	for (dat_idx = 0; dat_idx < hci->DAT_entries; dat_idx++) {
-		dat_w0_write(dat_idx, 0);
-		dat_w1_write(dat_idx, 0);
+	if (!hci->DAT_data) {
+		/* use a bitmap for faster free slot search */
+		hci->DAT_data = bitmap_zalloc(hci->DAT_entries, GFP_KERNEL);
+		if (!hci->DAT_data)
+			return -ENOMEM;
+
+		/* clear them */
+		for (dat_idx = 0; dat_idx < hci->DAT_entries; dat_idx++) {
+			dat_w0_write(dat_idx, 0);
+			dat_w1_write(dat_idx, 0);
+		}
 	}
 
 	return 0;
@@ -87,7 +89,13 @@
 static int hci_dat_v1_alloc_entry(struct i3c_hci *hci)
 {
 	unsigned int dat_idx;
+	int ret;
 
+	if (!hci->DAT_data) {
+		ret = hci_dat_v1_init(hci);
+		if (ret)
+			return ret;
+	}
 	dat_idx = find_first_zero_bit(hci->DAT_data, hci->DAT_entries);
 	if (dat_idx >= hci->DAT_entries)
 		return -ENOENT;
@@ -103,7 +111,8 @@
 {
 	dat_w0_write(dat_idx, 0);
 	dat_w1_write(dat_idx, 0);
-	__clear_bit(dat_idx, hci->DAT_data);
+	if (hci->DAT_data)
+		__clear_bit(dat_idx, hci->DAT_data);
 }
 
 static void hci_dat_v1_set_dynamic_addr(struct i3c_hci *hci,
@@ -160,9 +169,7 @@
 	unsigned int dat_idx;
 	u32 dat_w0;
 
-	for (dat_idx = find_first_bit(hci->DAT_data, hci->DAT_entries);
-	     dat_idx < hci->DAT_entries;
-	     dat_idx = find_next_bit(hci->DAT_data, hci->DAT_entries, dat_idx)) {
+	for_each_set_bit(dat_idx, hci->DAT_data, hci->DAT_entries) {
 		dat_w0 = dat_w0_read(dat_idx);
 		if (FIELD_GET(DAT_0_DYNAMIC_ADDRESS, dat_w0) == dev_addr)
 			return dat_idx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i3c/master/mipi-i3c-hci/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i3c/master/mipi-i3c-hci/dma.c
@@ -174,10 +174,10 @@
 	for (i = 0; i < rings->total; i++) {
 		rh = &rings->headers[i];
 
+		rh_reg_write(INTR_SIGNAL_ENABLE, 0);
 		rh_reg_write(RING_CONTROL, 0);
 		rh_reg_write(CR_SETUP, 0);
 		rh_reg_write(IBI_SETUP, 0);
-		rh_reg_write(INTR_SIGNAL_ENABLE, 0);
 
 		if (rh->xfer)
 			dma_free_coherent(&hci->master.dev,
@@ -291,7 +291,10 @@
 
 		rh->ibi_chunk_sz = dma_get_cache_alignment();
 		rh->ibi_chunk_sz *= IBI_CHUNK_CACHELINES;
-		BUG_ON(rh->ibi_chunk_sz > 256);
+		if (rh->ibi_chunk_sz > 256) {
+			ret = -EINVAL;
+			goto err_out;
+		}
 
 		ibi_status_ring_sz = rh->ibi_status_sz * rh->ibi_status_entries;
 		ibi_data_ring_sz = rh->ibi_chunk_sz * rh->ibi_chunks_total;
@@ -345,6 +348,8 @@
 
 	for (i = 0; i < n; i++) {
 		xfer = xfer_list + i;
+		if (!xfer->data)
+			continue;
 		dma_unmap_single(&hci->master.dev,
 				 xfer->data_dma, xfer->data_len,
 				 xfer->rnw ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
@@ -450,10 +455,9 @@
 		/*
 		 * We're deep in it if ever this condition is ever met.
 		 * Hardware might still be writing to memory, etc.
-		 * Better suspend the world than risking silent corruption.
 		 */
 		dev_crit(&hci->master.dev, "unable to abort the ring\n");
-		BUG();
+		WARN_ON(1);
 	}
 
 	for (i = 0; i < n; i++) {
@@ -734,7 +738,7 @@
 	unsigned int i;
 	bool handled = false;
 
-	for (i = 0; mask && i < 8; i++) {
+	for (i = 0; mask && i < rings->total; i++) {
 		struct hci_rh_data *rh;
 		u32 status;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/i3c/master/svc-i3c-master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/i3c/master/svc-i3c-master.c
@@ -165,6 +165,7 @@
  * @ibi.slots: Available IBI slots
  * @ibi.tbq_slot: To be queued IBI slot
  * @ibi.lock: IBI lock
+ * @lock: Transfer lock, protect between IBI work thread and callbacks from master
  */
 struct svc_i3c_master {
 	struct i3c_master_controller base;
@@ -192,6 +193,7 @@
 		/* Prevent races within IBI handlers */
 		spinlock_t lock;
 	} ibi;
+	struct mutex lock;
 };
 
 /**
@@ -292,6 +294,7 @@
 	struct i3c_ibi_slot *slot;
 	unsigned int count;
 	u32 mdatactrl;
+	int ret, val;
 	u8 *buf;
 
 	slot = i3c_generic_ibi_get_free_slot(data->ibi_pool);
@@ -301,6 +304,13 @@
 	slot->len = 0;
 	buf = slot->data;
 
+	ret = readl_relaxed_poll_timeout(master->regs + SVC_I3C_MSTATUS, val,
+						SVC_I3C_MSTATUS_COMPLETE(val), 0, 1000);
+	if (ret) {
+		dev_err(master->dev, "Timeout when polling for COMPLETE\n");
+		return ret;
+	}
+
 	while (SVC_I3C_MSTATUS_RXPEND(readl(master->regs + SVC_I3C_MSTATUS))  &&
 	       slot->len < SVC_I3C_FIFO_SIZE) {
 		mdatactrl = readl(master->regs + SVC_I3C_MDATACTRL);
@@ -345,6 +355,20 @@
 	u32 status, val;
 	int ret;
 
+	mutex_lock(&master->lock);
+	/*
+	 * IBIWON may be set before SVC_I3C_MCTRL_REQUEST_AUTO_IBI, causing
+	 * readl_relaxed_poll_timeout() to return immediately. Consequently,
+	 * ibitype will be 0 since it was last updated only after the 8th SCL
+	 * cycle, leading to missed client IBI handlers.
+	 *
+	 * A typical scenario is when IBIWON occurs and bus arbitration is lost
+	 * at svc_i3c_master_priv_xfers().
+	 *
+	 * Clear SVC_I3C_MINT_IBIWON before sending SVC_I3C_MCTRL_REQUEST_AUTO_IBI.
+	 */
+	writel(SVC_I3C_MINT_IBIWON, master->regs + SVC_I3C_MSTATUS);
+
 	/* Acknowledge the incoming interrupt with the AUTOIBI mechanism */
 	writel(SVC_I3C_MCTRL_REQUEST_AUTO_IBI |
 	       SVC_I3C_MCTRL_IBIRESP_AUTO,
@@ -355,12 +379,10 @@
 					 SVC_I3C_MSTATUS_IBIWON(val), 0, 1000);
 	if (ret) {
 		dev_err(master->dev, "Timeout when polling for IBIWON\n");
+		svc_i3c_master_emit_stop(master);
 		goto reenable_ibis;
 	}
 
-	/* Clear the interrupt status */
-	writel(SVC_I3C_MINT_IBIWON, master->regs + SVC_I3C_MSTATUS);
-
 	status = readl(master->regs + SVC_I3C_MSTATUS);
 	ibitype = SVC_I3C_MSTATUS_IBITYPE(status);
 	ibiaddr = SVC_I3C_MSTATUS_IBIADDR(status);
@@ -421,12 +443,13 @@
 
 reenable_ibis:
 	svc_i3c_master_enable_interrupts(master, SVC_I3C_MINT_SLVSTART);
+	mutex_unlock(&master->lock);
 }
 
 static irqreturn_t svc_i3c_master_irq_handler(int irq, void *dev_id)
 {
 	struct svc_i3c_master *master = (struct svc_i3c_master *)dev_id;
-	u32 active = readl(master->regs + SVC_I3C_MINTMASKED);
+	u32 active = readl(master->regs + SVC_I3C_MSTATUS);
 
 	if (!SVC_I3C_MSTATUS_SLVSTART(active))
 		return IRQ_NONE;
@@ -723,6 +746,10 @@
 				 */
 				break;
 			} else if (SVC_I3C_MSTATUS_NACKED(reg)) {
+				/* No I3C devices attached */
+				if (dev_nb == 0)
+					break;
+
 				/*
 				 * A slave device nacked the address, this is
 				 * allowed only once, DAA will be stopped and
@@ -780,7 +807,7 @@
 
 	/* Create the IBIRULES register for both cases */
 	i3c_bus_for_each_i3cdev(&master->base.bus, dev) {
-		if (I3C_BCR_DEVICE_ROLE(dev->info.bcr) == I3C_BCR_I3C_MASTER)
+		if (!(dev->info.bcr & I3C_BCR_IBI_REQ_CAP))
 			continue;
 
 		if (dev->info.bcr & I3C_BCR_IBI_PAYLOAD) {
@@ -922,6 +949,9 @@
 	u32 reg;
 	int ret;
 
+	/* clean SVC_I3C_MINT_IBIWON w1c bits */
+	writel(SVC_I3C_MINT_IBIWON, master->regs + SVC_I3C_MSTATUS);
+
 	writel(SVC_I3C_MCTRL_REQUEST_START_ADDR |
 	       xfer_type |
 	       SVC_I3C_MCTRL_IBIRESP_NACK |
@@ -935,6 +965,23 @@
 	if (ret)
 		goto emit_stop;
 
+	/*
+	 * According to I3C spec ver 1.1.1, 5.1.2.2.3 Consequence of Controller Starting a Frame
+	 * with I3C Target Address.
+	 *
+	 * The I3C Controller normally should start a Frame, the Address may be arbitrated, and so
+	 * the Controller shall monitor to see whether an In-Band Interrupt request, a Controller
+	 * Role Request (i.e., Secondary Controller requests to become the Active Controller), or
+	 * a Hot-Join Request has been made.
+	 *
+	 * If missed IBIWON check, the wrong data will be return. When IBIWON happen, return failure
+	 * and yield the above events handler.
+	 */
+	if (SVC_I3C_MSTATUS_IBIWON(reg)) {
+		ret = -ENXIO;
+		goto emit_stop;
+	}
+
 	if (rnw)
 		ret = svc_i3c_master_read(master, in, xfer_len);
 	else
@@ -1091,9 +1138,11 @@
 	cmd->read_len = 0;
 	cmd->continued = false;
 
+	mutex_lock(&master->lock);
 	svc_i3c_master_enqueue_xfer(master, xfer);
 	if (!wait_for_completion_timeout(&xfer->comp, msecs_to_jiffies(1000)))
 		svc_i3c_master_dequeue_xfer(master, xfer);
+	mutex_unlock(&master->lock);
 
 	ret = xfer->ret;
 	kfree(buf);
@@ -1137,9 +1186,11 @@
 	cmd->read_len = read_len;
 	cmd->continued = false;
 
+	mutex_lock(&master->lock);
 	svc_i3c_master_enqueue_xfer(master, xfer);
 	if (!wait_for_completion_timeout(&xfer->comp, msecs_to_jiffies(1000)))
 		svc_i3c_master_dequeue_xfer(master, xfer);
+	mutex_unlock(&master->lock);
 
 	ret = xfer->ret;
 	svc_i3c_master_free_xfer(xfer);
@@ -1152,11 +1203,17 @@
 {
 	struct svc_i3c_master *master = to_svc_i3c_master(m);
 	bool broadcast = cmd->id < 0x80;
+	int ret;
 
 	if (broadcast)
-		return svc_i3c_master_send_bdcast_ccc_cmd(master, cmd);
+		ret = svc_i3c_master_send_bdcast_ccc_cmd(master, cmd);
 	else
-		return svc_i3c_master_send_direct_ccc_cmd(master, cmd);
+		ret = svc_i3c_master_send_direct_ccc_cmd(master, cmd);
+
+	if (ret)
+		cmd->err = I3C_ERROR_M2;
+
+	return ret;
 }
 
 static int svc_i3c_master_priv_xfers(struct i3c_dev_desc *dev,
@@ -1187,9 +1244,11 @@
 		cmd->continued = (i + 1) < nxfers;
 	}
 
+	mutex_lock(&master->lock);
 	svc_i3c_master_enqueue_xfer(master, xfer);
 	if (!wait_for_completion_timeout(&xfer->comp, msecs_to_jiffies(1000)))
 		svc_i3c_master_dequeue_xfer(master, xfer);
+	mutex_unlock(&master->lock);
 
 	ret = xfer->ret;
 	svc_i3c_master_free_xfer(xfer);
@@ -1225,9 +1284,11 @@
 		cmd->continued = (i + 1 < nxfers);
 	}
 
+	mutex_lock(&master->lock);
 	svc_i3c_master_enqueue_xfer(master, xfer);
 	if (!wait_for_completion_timeout(&xfer->comp, msecs_to_jiffies(1000)))
 		svc_i3c_master_dequeue_xfer(master, xfer);
+	mutex_unlock(&master->lock);
 
 	ret = xfer->ret;
 	svc_i3c_master_free_xfer(xfer);
@@ -1397,6 +1458,8 @@
 
 	INIT_WORK(&master->hj_work, svc_i3c_master_hj_work);
 	INIT_WORK(&master->ibi_work, svc_i3c_master_ibi_work);
+	mutex_init(&master->lock);
+
 	ret = devm_request_irq(dev, master->irq, svc_i3c_master_irq_handler,
 			       IRQF_NO_SUSPEND, "svc-i3c-irq", master);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/idle/intel_idle.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/idle/intel_idle.c
@@ -47,13 +47,16 @@
 #include <linux/tick.h>
 #include <trace/events/power.h>
 #include <linux/sched.h>
+#include <linux/sched/smt.h>
 #include <linux/notifier.h>
 #include <linux/cpu.h>
 #include <linux/moduleparam.h>
 #include <asm/cpu_device_id.h>
 #include <asm/intel-family.h>
+#include <asm/nospec-branch.h>
 #include <asm/mwait.h>
 #include <asm/msr.h>
+#include <asm/tsc.h>
 
 #define INTEL_IDLE_VERSION "0.5.1"
 
@@ -64,11 +67,17 @@
 /* intel_idle.max_cstate=0 disables driver */
 static int max_cstate = CPUIDLE_STATE_MAX - 1;
 static unsigned int disabled_states_mask;
+static unsigned int preferred_states_mask;
 
 static struct cpuidle_device __percpu *intel_idle_cpuidle_devices;
 
 static unsigned long auto_demotion_disable_flags;
-static bool disable_promotion_to_c1e;
+
+static enum {
+	C1E_PROMOTION_PRESERVE,
+	C1E_PROMOTION_ENABLE,
+	C1E_PROMOTION_DISABLE
+} c1e_promotion = C1E_PROMOTION_PRESERVE;
 
 struct idle_cpu {
 	struct cpuidle_state *state_table;
@@ -94,6 +103,12 @@
 #define CPUIDLE_FLAG_ALWAYS_ENABLE	BIT(15)
 
 /*
+ * Disable IBRS across idle (when KERNEL_IBRS), is exclusive vs IRQ_ENABLE
+ * above.
+ */
+#define CPUIDLE_FLAG_IBRS		BIT(16)
+
+/*
  * MWAIT takes an 8-bit "hint" in EAX "suggesting"
  * the C-state (top nibble) and sub-state (bottom nibble)
  * 0x00 means "MWAIT(C1)", 0x10 means "MWAIT(C2)" etc.
@@ -132,6 +147,24 @@
 	return index;
 }
 
+static __cpuidle int intel_idle_ibrs(struct cpuidle_device *dev,
+				     struct cpuidle_driver *drv, int index)
+{
+	bool smt_active = sched_smt_active();
+	u64 spec_ctrl = spec_ctrl_current();
+	int ret;
+
+	if (smt_active)
+		wrmsrl(MSR_IA32_SPEC_CTRL, 0);
+
+	ret = intel_idle(dev, drv, index);
+
+	if (smt_active)
+		wrmsrl(MSR_IA32_SPEC_CTRL, spec_ctrl);
+
+	return ret;
+}
+
 /**
  * intel_idle_s2idle - Ask the processor to enter the given idle state.
  * @dev: cpuidle device of the target CPU.
@@ -653,7 +686,7 @@
 	{
 		.name = "C6",
 		.desc = "MWAIT 0x20",
-		.flags = MWAIT2flg(0x20) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.flags = MWAIT2flg(0x20) | CPUIDLE_FLAG_TLB_FLUSHED | CPUIDLE_FLAG_IBRS,
 		.exit_latency = 85,
 		.target_residency = 200,
 		.enter = &intel_idle,
@@ -661,7 +694,7 @@
 	{
 		.name = "C7s",
 		.desc = "MWAIT 0x33",
-		.flags = MWAIT2flg(0x33) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.flags = MWAIT2flg(0x33) | CPUIDLE_FLAG_TLB_FLUSHED | CPUIDLE_FLAG_IBRS,
 		.exit_latency = 124,
 		.target_residency = 800,
 		.enter = &intel_idle,
@@ -669,7 +702,7 @@
 	{
 		.name = "C8",
 		.desc = "MWAIT 0x40",
-		.flags = MWAIT2flg(0x40) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.flags = MWAIT2flg(0x40) | CPUIDLE_FLAG_TLB_FLUSHED | CPUIDLE_FLAG_IBRS,
 		.exit_latency = 200,
 		.target_residency = 800,
 		.enter = &intel_idle,
@@ -677,7 +710,7 @@
 	{
 		.name = "C9",
 		.desc = "MWAIT 0x50",
-		.flags = MWAIT2flg(0x50) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.flags = MWAIT2flg(0x50) | CPUIDLE_FLAG_TLB_FLUSHED | CPUIDLE_FLAG_IBRS,
 		.exit_latency = 480,
 		.target_residency = 5000,
 		.enter = &intel_idle,
@@ -685,7 +718,7 @@
 	{
 		.name = "C10",
 		.desc = "MWAIT 0x60",
-		.flags = MWAIT2flg(0x60) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.flags = MWAIT2flg(0x60) | CPUIDLE_FLAG_TLB_FLUSHED | CPUIDLE_FLAG_IBRS,
 		.exit_latency = 890,
 		.target_residency = 5000,
 		.enter = &intel_idle,
@@ -714,7 +747,7 @@
 	{
 		.name = "C6",
 		.desc = "MWAIT 0x20",
-		.flags = MWAIT2flg(0x20) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.flags = MWAIT2flg(0x20) | CPUIDLE_FLAG_TLB_FLUSHED | CPUIDLE_FLAG_IBRS,
 		.exit_latency = 133,
 		.target_residency = 600,
 		.enter = &intel_idle,
@@ -752,6 +785,35 @@
 		.enter = NULL }
 };
 
+static struct cpuidle_state spr_cstates[] __initdata = {
+	{
+		.name = "C1",
+		.desc = "MWAIT 0x00",
+		.flags = MWAIT2flg(0x00),
+		.exit_latency = 1,
+		.target_residency = 1,
+		.enter = &intel_idle,
+		.enter_s2idle = intel_idle_s2idle, },
+	{
+		.name = "C1E",
+		.desc = "MWAIT 0x01",
+		.flags = MWAIT2flg(0x01) | CPUIDLE_FLAG_ALWAYS_ENABLE,
+		.exit_latency = 2,
+		.target_residency = 4,
+		.enter = &intel_idle,
+		.enter_s2idle = intel_idle_s2idle, },
+	{
+		.name = "C6",
+		.desc = "MWAIT 0x20",
+		.flags = MWAIT2flg(0x20) | CPUIDLE_FLAG_TLB_FLUSHED,
+		.exit_latency = 290,
+		.target_residency = 800,
+		.enter = &intel_idle,
+		.enter_s2idle = intel_idle_s2idle, },
+	{
+		.enter = NULL }
+};
+
 static struct cpuidle_state atom_cstates[] __initdata = {
 	{
 		.name = "C1E",
@@ -1095,6 +1157,12 @@
 	.use_acpi = true,
 };
 
+static const struct idle_cpu idle_cpu_spr __initconst = {
+	.state_table = spr_cstates,
+	.disable_promotion_to_c1e = true,
+	.use_acpi = true,
+};
+
 static const struct idle_cpu idle_cpu_avn __initconst = {
 	.state_table = avn_cstates,
 	.disable_promotion_to_c1e = true,
@@ -1157,6 +1225,8 @@
 	X86_MATCH_INTEL_FAM6_MODEL(SKYLAKE_X,		&idle_cpu_skx),
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X,		&idle_cpu_icx),
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_D,		&idle_cpu_icx),
+	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X,	&idle_cpu_spr),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X,	&idle_cpu_spr),
 	X86_MATCH_INTEL_FAM6_MODEL(XEON_PHI_KNL,	&idle_cpu_knl),
 	X86_MATCH_INTEL_FAM6_MODEL(XEON_PHI_KNM,	&idle_cpu_knl),
 	X86_MATCH_INTEL_FAM6_MODEL(ATOM_GOLDMONT,	&idle_cpu_bxt),
@@ -1309,6 +1379,9 @@
 		if (intel_idle_state_needs_timer_stop(state))
 			state->flags |= CPUIDLE_FLAG_TIMER_STOP;
 
+		if (cx->type > ACPI_STATE_C1 && !boot_cpu_has(X86_FEATURE_NONSTOP_TSC))
+			mark_tsc_unstable("TSC halts in idle");
+
 		state->enter = intel_idle;
 		state->enter_s2idle = intel_idle_s2idle;
 	}
@@ -1514,6 +1587,27 @@
 	}
 }
 
+/**
+ * spr_idle_state_table_update - Adjust Sapphire Rapids idle states table.
+ */
+static void __init spr_idle_state_table_update(void)
+{
+	unsigned long long msr;
+
+	/*
+	 * By default, the C6 state assumes the worst-case scenario of package
+	 * C6. However, if PC6 is disabled, we update the numbers to match
+	 * core C6.
+	 */
+	rdmsrl(MSR_PKG_CST_CONFIG_CONTROL, msr);
+
+	/* Limit value 2 and above allow for PC6. */
+	if ((msr & 0x7) < 2) {
+		spr_cstates[2].exit_latency = 190;
+		spr_cstates[2].target_residency = 600;
+	}
+}
+
 static bool __init intel_idle_verify_cstate(unsigned int mwait_hint)
 {
 	unsigned int mwait_cstate = MWAIT_HINT2CSTATE(mwait_hint) + 1;
@@ -1548,6 +1642,10 @@
 	case INTEL_FAM6_SKYLAKE_X:
 		skx_idle_state_table_update();
 		break;
+	case INTEL_FAM6_SAPPHIRERAPIDS_X:
+	case INTEL_FAM6_EMERALDRAPIDS_X:
+		spr_idle_state_table_update();
+		break;
 	}
 
 	for (cstate = 0; cstate < CPUIDLE_STATE_MAX; ++cstate) {
@@ -1574,6 +1672,11 @@
 		/* Structure copy. */
 		drv->states[drv->state_count] = cpuidle_state_table[cstate];
 
+		if (cpu_feature_enabled(X86_FEATURE_KERNEL_IBRS) &&
+		    cpuidle_state_table[cstate].flags & CPUIDLE_FLAG_IBRS) {
+			drv->states[drv->state_count].enter = intel_idle_ibrs;
+		}
+
 		if ((disabled_states_mask & BIT(drv->state_count)) ||
 		    ((icpu->use_acpi || force_use_acpi) &&
 		     intel_idle_off_by_default(mwait_hint) &&
@@ -1620,6 +1723,15 @@
 	wrmsrl(MSR_PKG_CST_CONFIG_CONTROL, msr_bits);
 }
 
+static void c1e_promotion_enable(void)
+{
+	unsigned long long msr_bits;
+
+	rdmsrl(MSR_IA32_POWER_CTL, msr_bits);
+	msr_bits |= 0x2;
+	wrmsrl(MSR_IA32_POWER_CTL, msr_bits);
+}
+
 static void c1e_promotion_disable(void)
 {
 	unsigned long long msr_bits;
@@ -1651,7 +1763,9 @@
 	if (auto_demotion_disable_flags)
 		auto_demotion_disable();
 
-	if (disable_promotion_to_c1e)
+	if (c1e_promotion == C1E_PROMOTION_ENABLE)
+		c1e_promotion_enable();
+	else if (c1e_promotion == C1E_PROMOTION_DISABLE)
 		c1e_promotion_disable();
 
 	return 0;
@@ -1730,7 +1844,8 @@
 	if (icpu) {
 		cpuidle_state_table = icpu->state_table;
 		auto_demotion_disable_flags = icpu->auto_demotion_disable_flags;
-		disable_promotion_to_c1e = icpu->disable_promotion_to_c1e;
+		if (icpu->disable_promotion_to_c1e)
+			c1e_promotion = C1E_PROMOTION_DISABLE;
 		if (icpu->use_acpi || force_use_acpi)
 			intel_idle_acpi_cst_extract();
 	} else if (!intel_idle_acpi_cst_extract()) {
@@ -1789,3 +1904,14 @@
  */
 module_param_named(states_off, disabled_states_mask, uint, 0444);
 MODULE_PARM_DESC(states_off, "Mask of disabled idle states");
+/*
+ * Some platforms come with mutually exclusive C-states, so that if one is
+ * enabled, the other C-states must not be used. Example: C1 and C1E on
+ * Sapphire Rapids platform. This parameter allows for selecting the
+ * preferred C-states among the groups of mutually exclusive C-states - the
+ * selected C-states will be registered, the other C-states from the mutually
+ * exclusive group won't be registered. If the platform has no mutually
+ * exclusive C-states, this parameter has no effect.
+ */
+module_param_named(preferred_cstates, preferred_states_mask, uint, 0444);
+MODULE_PARM_DESC(preferred_cstates, "Mask of preferred idle states");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/Kconfig
@@ -70,6 +70,7 @@
 
 source "drivers/iio/accel/Kconfig"
 source "drivers/iio/adc/Kconfig"
+source "drivers/iio/addac/Kconfig"
 source "drivers/iio/afe/Kconfig"
 source "drivers/iio/amplifiers/Kconfig"
 source "drivers/iio/cdc/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/Makefile
@@ -15,6 +15,7 @@
 
 obj-y += accel/
 obj-y += adc/
+obj-y += addac/
 obj-y += afe/
 obj-y += amplifiers/
 obj-y += buffer/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/Kconfig
@@ -128,10 +128,12 @@
 
 config BMA400_I2C
 	tristate
+	select REGMAP_I2C
 	depends on BMA400
 
 config BMA400_SPI
 	tristate
+	select REGMAP_SPI
 	depends on BMA400
 
 config BMC150_ACCEL
@@ -233,6 +235,8 @@
 config FXLS8962AF
 	tristate
 	depends on I2C || !I2C # cannot be built-in for modular I2C
+	select IIO_BUFFER
+	select IIO_KFIFO_BUF
 
 config FXLS8962AF_I2C
 	tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/adis16201.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/adis16201.c
@@ -300,3 +300,4 @@
 MODULE_DESCRIPTION("Analog Devices ADIS16201 Dual-Axis Digital Inclinometer and Accelerometer");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("spi:adis16201");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/adis16209.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/adis16209.c
@@ -310,3 +310,4 @@
 MODULE_DESCRIPTION("Analog Devices ADIS16209 Dual-Axis Digital Inclinometer and Accelerometer");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("spi:adis16209");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/adxl372.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/adxl372.c
@@ -998,17 +998,30 @@
 	return sprintf(buf, "%d\n", st->watermark);
 }
 
-static IIO_CONST_ATTR(hwfifo_watermark_min, "1");
-static IIO_CONST_ATTR(hwfifo_watermark_max,
-		      __stringify(ADXL372_FIFO_SIZE));
+static ssize_t hwfifo_watermark_min_show(struct device *dev,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	return sysfs_emit(buf, "%s\n", "1");
+}
+
+static ssize_t hwfifo_watermark_max_show(struct device *dev,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	return sysfs_emit(buf, "%s\n", __stringify(ADXL372_FIFO_SIZE));
+}
+
+static IIO_DEVICE_ATTR_RO(hwfifo_watermark_min, 0);
+static IIO_DEVICE_ATTR_RO(hwfifo_watermark_max, 0);
 static IIO_DEVICE_ATTR(hwfifo_watermark, 0444,
 		       adxl372_get_fifo_watermark, NULL, 0);
 static IIO_DEVICE_ATTR(hwfifo_enabled, 0444,
 		       adxl372_get_fifo_enabled, NULL, 0);
 
 static const struct attribute *adxl372_fifo_attributes[] = {
-	&iio_const_attr_hwfifo_watermark_min.dev_attr.attr,
-	&iio_const_attr_hwfifo_watermark_max.dev_attr.attr,
+	&iio_dev_attr_hwfifo_watermark_min.dev_attr.attr,
+	&iio_dev_attr_hwfifo_watermark_max.dev_attr.attr,
 	&iio_dev_attr_hwfifo_watermark.dev_attr.attr,
 	&iio_dev_attr_hwfifo_enabled.dev_attr.attr,
 	NULL,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/bma180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/bma180.c
@@ -1006,11 +1006,12 @@
 
 		data->trig->ops = &bma180_trigger_ops;
 		iio_trigger_set_drvdata(data->trig, indio_dev);
-		indio_dev->trig = iio_trigger_get(data->trig);
 
 		ret = iio_trigger_register(data->trig);
 		if (ret)
 			goto err_trigger_free;
+
+		indio_dev->trig = iio_trigger_get(data->trig);
 	}
 
 	ret = iio_triggered_buffer_setup(indio_dev, NULL,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/bma400.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/bma400.h
@@ -83,8 +83,27 @@
 #define BMA400_ACC_ODR_MIN_WHOLE_HZ 25
 #define BMA400_ACC_ODR_MIN_HZ       12
 
-#define BMA400_SCALE_MIN            38357
-#define BMA400_SCALE_MAX            306864
+/*
+ * BMA400_SCALE_MIN macro value represents m/s^2 for 1 LSB before
+ * converting to micro values for +-2g range.
+ *
+ * For +-2g - 1 LSB = 0.976562 milli g = 0.009576 m/s^2
+ * For +-4g - 1 LSB = 1.953125 milli g = 0.019153 m/s^2
+ * For +-16g - 1 LSB = 7.8125 milli g = 0.076614 m/s^2
+ *
+ * The raw value which is used to select the different ranges is determined
+ * by the first bit set position from the scale value, so BMA400_SCALE_MIN
+ * should be odd.
+ *
+ * Scale values for +-2g, +-4g, +-8g and +-16g are populated into bma400_scales
+ * array by left shifting BMA400_SCALE_MIN.
+ * e.g.:
+ * To select +-2g = 9577 << 0 = raw value to write is 0.
+ * To select +-8g = 9577 << 2 = raw value to write is 2.
+ * To select +-16g = 9577 << 3 = raw value to write is 3.
+ */
+#define BMA400_SCALE_MIN            9577
+#define BMA400_SCALE_MAX            76617
 
 #define BMA400_NUM_REGULATORS       2
 #define BMA400_VDD_REGULATOR        0
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/bma400_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/bma400_core.c
@@ -13,14 +13,14 @@
 
 #include <linux/bitops.h>
 #include <linux/device.h>
-#include <linux/iio/iio.h>
-#include <linux/iio/sysfs.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 
+#include <linux/iio/iio.h>
+
 #include "bma400.h"
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/bmc150-accel-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/bmc150-accel-core.c
@@ -1525,7 +1525,7 @@
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
 	int ret = 0;
 
-	if (indio_dev->currentmode == INDIO_BUFFER_TRIGGERED)
+	if (iio_device_get_current_mode(indio_dev) == INDIO_BUFFER_TRIGGERED)
 		return 0;
 
 	mutex_lock(&data->mutex);
@@ -1557,7 +1557,7 @@
 {
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
 
-	if (indio_dev->currentmode == INDIO_BUFFER_TRIGGERED)
+	if (iio_device_get_current_mode(indio_dev) == INDIO_BUFFER_TRIGGERED)
 		return 0;
 
 	mutex_lock(&data->mutex);
@@ -1782,11 +1782,14 @@
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(dev, "Unable to register iio device\n");
-		goto err_trigger_unregister;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(dev);
+	pm_runtime_disable(dev);
 err_trigger_unregister:
 	bmc150_accel_unregister_triggers(data, BMC150_ACCEL_TRIGGERS - 1);
 err_buffer_cleanup:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/cros_ec_accel_legacy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/cros_ec_accel_legacy.c
@@ -215,7 +215,7 @@
 		return -ENOMEM;
 
 	ret = cros_ec_sensors_core_init(pdev, indio_dev, true,
-					cros_ec_sensors_capture, NULL);
+					cros_ec_sensors_capture);
 	if (ret)
 		return ret;
 
@@ -235,7 +235,7 @@
 		state->sign[CROS_EC_SENSOR_Z] = -1;
 	}
 
-	return devm_iio_device_register(dev, indio_dev);
+	return cros_ec_sensors_core_register(dev, indio_dev, NULL);
 }
 
 static struct platform_driver cros_ec_accel_platform_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/fxls8962af-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/fxls8962af-core.c
@@ -154,12 +154,20 @@
 	u8 watermark;
 };
 
-const struct regmap_config fxls8962af_regmap_conf = {
+const struct regmap_config fxls8962af_i2c_regmap_conf = {
 	.reg_bits = 8,
 	.val_bits = 8,
 	.max_register = FXLS8962AF_MAX_REG,
 };
-EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
+EXPORT_SYMBOL_GPL(fxls8962af_i2c_regmap_conf);
+
+const struct regmap_config fxls8962af_spi_regmap_conf = {
+	.reg_bits = 8,
+	.pad_bits = 8,
+	.val_bits = 8,
+	.max_register = FXLS8962AF_MAX_REG,
+};
+EXPORT_SYMBOL_GPL(fxls8962af_spi_regmap_conf);
 
 enum {
 	fxls8962af_idx_x,
@@ -478,8 +486,7 @@
 		.sign = 's', \
 		.realbits = 12, \
 		.storagebits = 16, \
-		.shift = 4, \
-		.endianness = IIO_BE, \
+		.endianness = IIO_LE, \
 	}, \
 }
 
@@ -648,9 +655,10 @@
 	int total_length = samples * sample_length;
 	int ret;
 
-	if (i2c_verify_client(dev))
+	if (i2c_verify_client(dev) &&
+	    data->chip_info->chip_id == FXLS8962AF_DEVICE_ID)
 		/*
-		 * Due to errata bug:
+		 * Due to errata bug (only applicable on fxls8962af):
 		 * E3: FIFO burst read operation error using I2C interface
 		 * We have to avoid burst reads on I2C..
 		 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/fxls8962af-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/fxls8962af-i2c.c
@@ -18,7 +18,7 @@
 {
 	struct regmap *regmap;
 
-	regmap = devm_regmap_init_i2c(client, &fxls8962af_regmap_conf);
+	regmap = devm_regmap_init_i2c(client, &fxls8962af_i2c_regmap_conf);
 	if (IS_ERR(regmap)) {
 		dev_err(&client->dev, "Failed to initialize i2c regmap\n");
 		return PTR_ERR(regmap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/fxls8962af-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/fxls8962af-spi.c
@@ -18,7 +18,7 @@
 {
 	struct regmap *regmap;
 
-	regmap = devm_regmap_init_spi(spi, &fxls8962af_regmap_conf);
+	regmap = devm_regmap_init_spi(spi, &fxls8962af_spi_regmap_conf);
 	if (IS_ERR(regmap)) {
 		dev_err(&spi->dev, "Failed to initialize spi regmap\n");
 		return PTR_ERR(regmap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/fxls8962af.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/fxls8962af.h
@@ -17,6 +17,7 @@
 int fxls8962af_core_remove(struct device *dev);
 
 extern const struct dev_pm_ops fxls8962af_pm_ops;
-extern const struct regmap_config fxls8962af_regmap_conf;
+extern const struct regmap_config fxls8962af_i2c_regmap_conf;
+extern const struct regmap_config fxls8962af_spi_regmap_conf;
 
 #endif				/* _FXLS8962AF_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/hid-sensor-accel-3d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/hid-sensor-accel-3d.c
@@ -280,6 +280,7 @@
 			hid_sensor_convert_timestamp(
 					&accel_state->common_attributes,
 					*(int64_t *)raw_data);
+		ret = 0;
 	break;
 	default:
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/kxcjk-1013.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/kxcjk-1013.c
@@ -1553,12 +1553,12 @@
 
 		data->dready_trig->ops = &kxcjk1013_trigger_ops;
 		iio_trigger_set_drvdata(data->dready_trig, indio_dev);
-		indio_dev->trig = data->dready_trig;
-		iio_trigger_get(indio_dev->trig);
 		ret = iio_trigger_register(data->dready_trig);
 		if (ret)
 			goto err_poweroff;
 
+		indio_dev->trig = iio_trigger_get(data->dready_trig);
+
 		data->motion_trig->ops = &kxcjk1013_trigger_ops;
 		iio_trigger_set_drvdata(data->motion_trig, indio_dev);
 		ret = iio_trigger_register(data->motion_trig);
@@ -1589,14 +1589,16 @@
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "unable to register iio device\n");
-		goto err_buffer_cleanup;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 err_buffer_cleanup:
-	if (data->dready_trig)
-		iio_triggered_buffer_cleanup(indio_dev);
+	iio_triggered_buffer_cleanup(indio_dev);
 err_trigger_unregister:
 	if (data->dready_trig)
 		iio_trigger_unregister(data->dready_trig);
@@ -1618,8 +1620,8 @@
 	pm_runtime_disable(&client->dev);
 	pm_runtime_set_suspended(&client->dev);
 
+	iio_triggered_buffer_cleanup(indio_dev);
 	if (data->dready_trig) {
-		iio_triggered_buffer_cleanup(indio_dev);
 		iio_trigger_unregister(data->dready_trig);
 		iio_trigger_unregister(data->motion_trig);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/kxsd9.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/kxsd9.c
@@ -224,14 +224,14 @@
 			       hw_values.chan,
 			       sizeof(hw_values.chan));
 	if (ret) {
-		dev_err(st->dev,
-			"error reading data\n");
-		return ret;
+		dev_err(st->dev, "error reading data: %d\n", ret);
+		goto out;
 	}
 
 	iio_push_to_buffers_with_timestamp(indio_dev,
 					   &hw_values,
 					   iio_get_time_ns(indio_dev));
+out:
 	iio_trigger_notify_done(indio_dev->trig);
 
 	return IRQ_HANDLED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/mma8452.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/mma8452.c
@@ -176,6 +176,7 @@
  * @enabled_events:		event flags enabled and handled by this driver
  */
 struct mma_chip_info {
+	const char *name;
 	u8 chip_id;
 	const struct iio_chan_spec *channels;
 	int num_channels;
@@ -379,8 +380,8 @@
 					struct device_attribute *attr,
 					char *buf)
 {
-	struct mma8452_data *data = iio_priv(i2c_get_clientdata(
-					     to_i2c_client(dev)));
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct mma8452_data *data = iio_priv(indio_dev);
 
 	return mma8452_show_int_plus_micros(buf, data->chip_info->mma_scales,
 		ARRAY_SIZE(data->chip_info->mma_scales));
@@ -708,7 +709,7 @@
 			     int val, int val2, long mask)
 {
 	struct mma8452_data *data = iio_priv(indio_dev);
-	int i, ret;
+	int i, j, ret;
 
 	ret = iio_device_claim_direct_mode(indio_dev);
 	if (ret)
@@ -768,14 +769,18 @@
 		break;
 
 	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
-		ret = mma8452_get_odr_index(data);
+		j = mma8452_get_odr_index(data);
 
 		for (i = 0; i < ARRAY_SIZE(mma8452_os_ratio); i++) {
-			if (mma8452_os_ratio[i][ret] == val) {
+			if (mma8452_os_ratio[i][j] == val) {
 				ret = mma8452_set_power_mode(data, i);
 				break;
 			}
 		}
+		if (i == ARRAY_SIZE(mma8452_os_ratio)) {
+			ret = -EINVAL;
+			break;
+		}
 		break;
 	default:
 		ret = -EINVAL;
@@ -1301,6 +1306,7 @@
 
 static const struct mma_chip_info mma_chip_info_table[] = {
 	[mma8451] = {
+		.name = "mma8451",
 		.chip_id = MMA8451_DEVICE_ID,
 		.channels = mma8451_channels,
 		.num_channels = ARRAY_SIZE(mma8451_channels),
@@ -1325,6 +1331,7 @@
 					MMA8452_INT_FF_MT,
 	},
 	[mma8452] = {
+		.name = "mma8452",
 		.chip_id = MMA8452_DEVICE_ID,
 		.channels = mma8452_channels,
 		.num_channels = ARRAY_SIZE(mma8452_channels),
@@ -1341,6 +1348,7 @@
 					MMA8452_INT_FF_MT,
 	},
 	[mma8453] = {
+		.name = "mma8453",
 		.chip_id = MMA8453_DEVICE_ID,
 		.channels = mma8453_channels,
 		.num_channels = ARRAY_SIZE(mma8453_channels),
@@ -1357,6 +1365,7 @@
 					MMA8452_INT_FF_MT,
 	},
 	[mma8652] = {
+		.name = "mma8652",
 		.chip_id = MMA8652_DEVICE_ID,
 		.channels = mma8652_channels,
 		.num_channels = ARRAY_SIZE(mma8652_channels),
@@ -1366,6 +1375,7 @@
 		.enabled_events = MMA8452_INT_FF_MT,
 	},
 	[mma8653] = {
+		.name = "mma8653",
 		.chip_id = MMA8653_DEVICE_ID,
 		.channels = mma8653_channels,
 		.num_channels = ARRAY_SIZE(mma8653_channels),
@@ -1380,6 +1390,7 @@
 		.enabled_events = MMA8452_INT_FF_MT,
 	},
 	[fxls8471] = {
+		.name = "fxls8471",
 		.chip_id = FXLS8471_DEVICE_ID,
 		.channels = mma8451_channels,
 		.num_channels = ARRAY_SIZE(mma8451_channels),
@@ -1470,7 +1481,7 @@
 	if (ret)
 		return ret;
 
-	indio_dev->trig = trig;
+	indio_dev->trig = iio_trigger_get(trig);
 
 	return 0;
 }
@@ -1486,10 +1497,14 @@
 	int i;
 	int ret;
 
-	ret = i2c_smbus_write_byte_data(client,	MMA8452_CTRL_REG2,
+	/*
+	 * Find on fxls8471, after config reset bit, it reset immediately,
+	 * and will not give ACK, so here do not check the return value.
+	 * The following code will read the reset register, and check whether
+	 * this reset works.
+	 */
+	i2c_smbus_write_byte_data(client, MMA8452_CTRL_REG2,
 					MMA8452_CTRL_REG2_RST);
-	if (ret < 0)
-		return ret;
 
 	for (i = 0; i < 10; i++) {
 		usleep_range(100, 200);
@@ -1522,13 +1537,6 @@
 	struct mma8452_data *data;
 	struct iio_dev *indio_dev;
 	int ret;
-	const struct of_device_id *match;
-
-	match = of_match_device(mma8452_dt_ids, &client->dev);
-	if (!match) {
-		dev_err(&client->dev, "unknown device model\n");
-		return -ENODEV;
-	}
 
 	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
 	if (!indio_dev)
@@ -1537,7 +1545,16 @@
 	data = iio_priv(indio_dev);
 	data->client = client;
 	mutex_init(&data->lock);
-	data->chip_info = match->data;
+
+	data->chip_info = device_get_match_data(&client->dev);
+	if (!data->chip_info) {
+		if (id) {
+			data->chip_info = &mma_chip_info_table[id->driver_data];
+		} else {
+			dev_err(&client->dev, "unknown device model\n");
+			return -ENODEV;
+		}
+	}
 
 	data->vdd_reg = devm_regulator_get(&client->dev, "vdd");
 	if (IS_ERR(data->vdd_reg))
@@ -1581,11 +1598,11 @@
 	}
 
 	dev_info(&client->dev, "registering %s accelerometer; ID 0x%x\n",
-		 match->compatible, data->chip_info->chip_id);
+		 data->chip_info->name, data->chip_info->chip_id);
 
 	i2c_set_clientdata(client, indio_dev);
 	indio_dev->info = &mma8452_info;
-	indio_dev->name = id->name;
+	indio_dev->name = data->chip_info->name;
 	indio_dev->modes = INDIO_DIRECT_MODE;
 	indio_dev->channels = data->chip_info->channels;
 	indio_dev->num_channels = data->chip_info->num_channels;
@@ -1810,7 +1827,7 @@
 static struct i2c_driver mma8452_driver = {
 	.driver = {
 		.name	= "mma8452",
-		.of_match_table = of_match_ptr(mma8452_dt_ids),
+		.of_match_table = mma8452_dt_ids,
 		.pm	= &mma8452_pm_ops,
 	},
 	.probe = mma8452_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/mma9551.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/mma9551.c
@@ -495,11 +495,14 @@
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "unable to register iio device\n");
-		goto out_poweroff;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 out_poweroff:
 	mma9551_set_device_state(client, false);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/mma9551_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/mma9551_core.c
@@ -296,9 +296,12 @@
 
 	ret = mma9551_transfer(client, app_id, MMA9551_CMD_READ_CONFIG,
 			       reg, NULL, 0, (u8 *)&v, 2);
+	if (ret < 0)
+		return ret;
+
 	*val = be16_to_cpu(v);
 
-	return ret;
+	return 0;
 }
 EXPORT_SYMBOL(mma9551_read_config_word);
 
@@ -354,9 +357,12 @@
 
 	ret = mma9551_transfer(client, app_id, MMA9551_CMD_READ_STATUS,
 			       reg, NULL, 0, (u8 *)&v, 2);
+	if (ret < 0)
+		return ret;
+
 	*val = be16_to_cpu(v);
 
-	return ret;
+	return 0;
 }
 EXPORT_SYMBOL(mma9551_read_status_word);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/mma9553.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/mma9553.c
@@ -1134,12 +1134,15 @@
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "unable to register iio device\n");
-		goto out_poweroff;
+		goto err_pm_cleanup;
 	}
 
 	dev_dbg(&indio_dev->dev, "Registered device %s\n", name);
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 out_poweroff:
 	mma9551_set_device_state(client, false);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/mxc4005.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/mxc4005.c
@@ -5,6 +5,7 @@
  * Copyright (c) 2014, Intel Corporation.
  */
 
+#include <linux/delay.h>
 #include <linux/module.h>
 #include <linux/i2c.h>
 #include <linux/iio/iio.h>
@@ -27,11 +28,16 @@
 #define MXC4005_REG_ZOUT_UPPER		0x07
 #define MXC4005_REG_ZOUT_LOWER		0x08
 
+#define MXC4005_REG_INT_MASK0		0x0A
+
 #define MXC4005_REG_INT_MASK1		0x0B
 #define MXC4005_REG_INT_MASK1_BIT_DRDYE	0x01
 
+#define MXC4005_REG_INT_CLR0		0x00
+
 #define MXC4005_REG_INT_CLR1		0x01
 #define MXC4005_REG_INT_CLR1_BIT_DRDYC	0x01
+#define MXC4005_REG_INT_CLR1_SW_RST	0x10
 
 #define MXC4005_REG_CONTROL		0x0D
 #define MXC4005_REG_CONTROL_MASK_FSR	GENMASK(6, 5)
@@ -39,6 +45,9 @@
 
 #define MXC4005_REG_DEVICE_ID		0x0E
 
+/* Datasheet does not specify a reset time, this is a conservative guess */
+#define MXC4005_RESET_TIME_US		2000
+
 enum mxc4005_axis {
 	AXIS_X,
 	AXIS_Y,
@@ -62,6 +71,8 @@
 		s64 timestamp __aligned(8);
 	} scan;
 	bool trigger_enabled;
+	unsigned int control;
+	unsigned int int_mask1;
 };
 
 /*
@@ -113,7 +124,9 @@
 static bool mxc4005_is_writeable_reg(struct device *dev, unsigned int reg)
 {
 	switch (reg) {
+	case MXC4005_REG_INT_CLR0:
 	case MXC4005_REG_INT_CLR1:
+	case MXC4005_REG_INT_MASK0:
 	case MXC4005_REG_INT_MASK1:
 	case MXC4005_REG_CONTROL:
 		return true;
@@ -330,23 +343,20 @@
 {
 	struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
 	struct mxc4005_data *data = iio_priv(indio_dev);
+	unsigned int val;
 	int ret;
 
 	mutex_lock(&data->mutex);
-	if (state) {
-		ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK1,
-				   MXC4005_REG_INT_MASK1_BIT_DRDYE);
-	} else {
-		ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK1,
-				   ~MXC4005_REG_INT_MASK1_BIT_DRDYE);
-	}
 
+	val = state ? MXC4005_REG_INT_MASK1_BIT_DRDYE : 0;
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK1, val);
 	if (ret < 0) {
 		mutex_unlock(&data->mutex);
 		dev_err(data->dev, "failed to update reg_int_mask1");
 		return ret;
 	}
 
+	data->int_mask1 = val;
 	data->trigger_enabled = state;
 	mutex_unlock(&data->mutex);
 
@@ -382,6 +392,21 @@
 
 	dev_dbg(data->dev, "MXC4005 chip id %02x\n", reg);
 
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_CLR1,
+			   MXC4005_REG_INT_CLR1_SW_RST);
+	if (ret < 0)
+		return dev_err_probe(data->dev, ret, "resetting chip\n");
+
+	fsleep(MXC4005_RESET_TIME_US);
+
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK0, 0);
+	if (ret < 0)
+		return dev_err_probe(data->dev, ret, "writing INT_MASK0\n");
+
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK1, 0);
+	if (ret < 0)
+		return dev_err_probe(data->dev, ret, "writing INT_MASK1\n");
+
 	return 0;
 }
 
@@ -456,8 +481,6 @@
 
 		data->dready_trig->ops = &mxc4005_trigger_ops;
 		iio_trigger_set_drvdata(data->dready_trig, indio_dev);
-		indio_dev->trig = data->dready_trig;
-		iio_trigger_get(indio_dev->trig);
 		ret = devm_iio_trigger_register(&client->dev,
 						data->dready_trig);
 		if (ret) {
@@ -465,11 +488,65 @@
 				"failed to register trigger\n");
 			return ret;
 		}
+
+		indio_dev->trig = iio_trigger_get(data->dready_trig);
 	}
 
 	return devm_iio_device_register(&client->dev, indio_dev);
 }
 
+static int mxc4005_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct mxc4005_data *data = iio_priv(indio_dev);
+	int ret;
+
+	/* Save control to restore it on resume */
+	ret = regmap_read(data->regmap, MXC4005_REG_CONTROL, &data->control);
+	if (ret < 0)
+		dev_err(data->dev, "failed to read reg_control\n");
+
+	return ret;
+}
+
+static int mxc4005_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct mxc4005_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_CLR1,
+			   MXC4005_REG_INT_CLR1_SW_RST);
+	if (ret) {
+		dev_err(data->dev, "failed to reset chip: %d\n", ret);
+		return ret;
+	}
+
+	fsleep(MXC4005_RESET_TIME_US);
+
+	ret = regmap_write(data->regmap, MXC4005_REG_CONTROL, data->control);
+	if (ret) {
+		dev_err(data->dev, "failed to restore control register\n");
+		return ret;
+	}
+
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK0, 0);
+	if (ret) {
+		dev_err(data->dev, "failed to restore interrupt 0 mask\n");
+		return ret;
+	}
+
+	ret = regmap_write(data->regmap, MXC4005_REG_INT_MASK1, data->int_mask1);
+	if (ret) {
+		dev_err(data->dev, "failed to restore interrupt 1 mask\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(mxc4005_pm_ops, mxc4005_suspend, mxc4005_resume);
+
 static const struct acpi_device_id mxc4005_acpi_match[] = {
 	{"MXC4005",	0},
 	{"MXC6655",	0},
@@ -488,6 +565,7 @@
 	.driver = {
 		.name = MXC4005_DRV_NAME,
 		.acpi_match_table = ACPI_PTR(mxc4005_acpi_match),
+		.pm = pm_sleep_ptr(&mxc4005_pm_ops),
 	},
 	.probe		= mxc4005_probe,
 	.id_table	= mxc4005_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/st_accel_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/st_accel_core.c
@@ -1212,12 +1212,12 @@
 
 	adev = ACPI_COMPANION(adata->dev);
 	if (!adev)
-		return 0;
+		return -ENXIO;
 
 	/* Read _ONT data, which should be a package of 6 integers. */
 	status = acpi_evaluate_object(adev->handle, "_ONT", NULL, &buffer);
 	if (status == AE_NOT_FOUND) {
-		return 0;
+		return -ENXIO;
 	} else if (ACPI_FAILURE(status)) {
 		dev_warn(&indio_dev->dev, "failed to execute _ONT: %d\n",
 			 status);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/st_accel_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/st_accel_i2c.c
@@ -193,10 +193,10 @@
 {
 	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_accel_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/accel/st_accel_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/accel/st_accel_spi.c
@@ -143,10 +143,10 @@
 {
 	struct iio_dev *indio_dev = spi_get_drvdata(spi);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_accel_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/Kconfig
@@ -499,6 +499,18 @@
 	  Say yes here to build support for TI INA2xx family of Power Monitors.
 	  This driver is mutually exclusive with the HWMON version.
 
+config INA260_ADC
+	tristate "Texas Instruments INA260 Power Monitors IIO driver"
+	depends on I2C && !SENSORS_INA2XX
+	select REGMAP_I2C
+	select IIO_BUFFER
+	select IIO_KFIFO_BUF
+	help
+	  Say yes here to build support for TI INA260 power monitor.
+	  This driver can also be built as a module. It supports software buffer
+	  mode and raw reads of ina260 iio channels. Up to 4 channels are
+	  supported including timestamp.
+
 config INGENIC_ADC
 	tristate "Ingenic JZ47xx SoCs ADC driver"
 	depends on MIPS || COMPILE_TEST
@@ -991,22 +1003,6 @@
 	  Say yes here to build support for ST Microelectronics STMPE
 	  built-in ADC block (stmpe811).
 
-config STX104
-	tristate "Apex Embedded Systems STX104 driver"
-	depends on PC104 && X86
-	select ISA_BUS_API
-	select GPIOLIB
-	help
-	  Say yes here to build support for the Apex Embedded Systems STX104
-	  integrated analog PC/104 card.
-
-	  This driver supports the 16 channels of single-ended (8 channels of
-	  differential) analog inputs, 2 channels of analog output, 4 digital
-	  inputs, and 4 digital outputs provided by the STX104.
-
-	  The base port addresses for the devices may be configured via the base
-	  array module parameter.
-
 config SUN4I_GPADC
 	tristate "Support for the Allwinner SoCs GPADC"
 	depends on IIO
@@ -1147,6 +1143,8 @@
 config TI_ADS8688
 	tristate "Texas Instruments ADS8688"
 	depends on SPI && OF
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	help
 	  If you say yes here you get support for Texas Instruments ADS8684 and
 	  and ADS8688 ADC chips
@@ -1157,6 +1155,8 @@
 config TI_ADS124S08
 	tristate "Texas Instruments ADS124S08"
 	depends on SPI && OF
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	help
 	  If you say yes here you get support for Texas Instruments ADS124S08
 	  and ADS124S06 ADC chips
@@ -1278,4 +1278,25 @@
 	  The driver can also be build as a module. If so, the module will be called
 	  xilinx-xadc.
 
+config XILINX_AMS
+       tristate "Xilinx AMS driver"
+       depends on ARCH_ZYNQMP || COMPILE_TEST
+       depends on HAS_IOMEM
+       help
+         Say yes here to have support for the Xilinx AMS.
+
+         The driver can also be build as a module. If so, the module will be called
+         xilinx-ams.
+
+config VERSAL_SYSMON
+	tristate "Xilinx Sysmon driver for Versal"
+	depends on HAS_IOMEM
+	help
+	  Say yes here to have support for the Xilinx Sysmon.
+	  The driver will enable users to monitor temperature and voltage on the
+	  Xilinx Versal platform.
+	  The HW also supports I2C access but it is not supported by the driver.
+
+	  The driver can also be build as a module. If so, the module will be called
+	  versal-sysmon.
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/Makefile
@@ -47,6 +47,7 @@
 obj-$(CONFIG_HX711) += hx711.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
 obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
+obj-$(CONFIG_INA260_ADC) += ina260-adc.o
 obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
 obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o
 obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
@@ -85,7 +86,6 @@
 obj-$(CONFIG_RZG2L_ADC) += rzg2l_adc.o
 obj-$(CONFIG_SC27XX_ADC) += sc27xx_adc.o
 obj-$(CONFIG_SPEAR_ADC) += spear_adc.o
-obj-$(CONFIG_STX104) += stx104.o
 obj-$(CONFIG_SUN4I_GPADC) += sun4i-gpadc-iio.o
 obj-$(CONFIG_STM32_ADC_CORE) += stm32-adc-core.o
 obj-$(CONFIG_STM32_ADC) += stm32-adc.o
@@ -114,4 +114,6 @@
 obj-$(CONFIG_VIPERBOARD_ADC) += viperboard_adc.o
 xilinx-xadc-y := xilinx-xadc-core.o xilinx-xadc-events.o
 obj-$(CONFIG_XILINX_XADC) += xilinx-xadc.o
+obj-$(CONFIG_XILINX_AMS) += xilinx-ams.o
 obj-$(CONFIG_SD_ADC_MODULATOR) += sd_adc_modulator.o
+obj-$(CONFIG_VERSAL_SYSMON) += versal-sysmon.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7091r-base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7091r-base.c
@@ -6,6 +6,7 @@
  */
 
 #include <linux/bitops.h>
+#include <linux/bitfield.h>
 #include <linux/iio/events.h>
 #include <linux/iio/iio.h>
 #include <linux/interrupt.h>
@@ -28,6 +29,7 @@
 #define AD7091R_REG_RESULT_CONV_RESULT(x)   ((x) & 0xfff)
 
 /* AD7091R_REG_CONF */
+#define AD7091R_REG_CONF_ALERT_EN   BIT(4)
 #define AD7091R_REG_CONF_AUTO   BIT(8)
 #define AD7091R_REG_CONF_CMD    BIT(10)
 
@@ -49,6 +51,27 @@
 	struct mutex lock; /*lock to prevent concurent reads */
 };
 
+const struct iio_event_spec ad7091r_events[] = {
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_RISING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE) |
+				 BIT(IIO_EV_INFO_ENABLE),
+	},
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_FALLING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE) |
+				 BIT(IIO_EV_INFO_ENABLE),
+	},
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_EITHER,
+		.mask_separate = BIT(IIO_EV_INFO_HYSTERESIS),
+	},
+};
+EXPORT_SYMBOL_NS_GPL(ad7091r_events, IIO_AD7091R);
+
 static int ad7091r_set_mode(struct ad7091r_state *st, enum ad7091r_mode mode)
 {
 	int ret, conf;
@@ -168,14 +191,148 @@
 	return ret;
 }
 
+static int ad7091r_read_event_config(struct iio_dev *indio_dev,
+				     const struct iio_chan_spec *chan,
+				     enum iio_event_type type,
+				     enum iio_event_direction dir)
+{
+	struct ad7091r_state *st = iio_priv(indio_dev);
+	int val, ret;
+
+	switch (dir) {
+	case IIO_EV_DIR_RISING:
+		ret = regmap_read(st->map,
+				  AD7091R_REG_CH_HIGH_LIMIT(chan->channel),
+				  &val);
+		if (ret)
+			return ret;
+		return val != AD7091R_HIGH_LIMIT;
+	case IIO_EV_DIR_FALLING:
+		ret = regmap_read(st->map,
+				  AD7091R_REG_CH_LOW_LIMIT(chan->channel),
+				  &val);
+		if (ret)
+			return ret;
+		return val != AD7091R_LOW_LIMIT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int ad7091r_write_event_config(struct iio_dev *indio_dev,
+				      const struct iio_chan_spec *chan,
+				      enum iio_event_type type,
+				      enum iio_event_direction dir, int state)
+{
+	struct ad7091r_state *st = iio_priv(indio_dev);
+
+	if (state) {
+		return regmap_set_bits(st->map, AD7091R_REG_CONF,
+				       AD7091R_REG_CONF_ALERT_EN);
+	} else {
+		/*
+		 * Set thresholds either to 0 or to 2^12 - 1 as appropriate to
+		 * prevent alerts and thus disable event generation.
+		 */
+		switch (dir) {
+		case IIO_EV_DIR_RISING:
+			return regmap_write(st->map,
+					    AD7091R_REG_CH_HIGH_LIMIT(chan->channel),
+					    AD7091R_HIGH_LIMIT);
+		case IIO_EV_DIR_FALLING:
+			return regmap_write(st->map,
+					    AD7091R_REG_CH_LOW_LIMIT(chan->channel),
+					    AD7091R_LOW_LIMIT);
+		default:
+			return -EINVAL;
+		}
+	}
+}
+
+static int ad7091r_read_event_value(struct iio_dev *indio_dev,
+				    const struct iio_chan_spec *chan,
+				    enum iio_event_type type,
+				    enum iio_event_direction dir,
+				    enum iio_event_info info, int *val, int *val2)
+{
+	struct ad7091r_state *st = iio_priv(indio_dev);
+	int ret;
+
+	switch (info) {
+	case IIO_EV_INFO_VALUE:
+		switch (dir) {
+		case IIO_EV_DIR_RISING:
+			ret = regmap_read(st->map,
+					  AD7091R_REG_CH_HIGH_LIMIT(chan->channel),
+					  val);
+			if (ret)
+				return ret;
+			return IIO_VAL_INT;
+		case IIO_EV_DIR_FALLING:
+			ret = regmap_read(st->map,
+					  AD7091R_REG_CH_LOW_LIMIT(chan->channel),
+					  val);
+			if (ret)
+				return ret;
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+	case IIO_EV_INFO_HYSTERESIS:
+		ret = regmap_read(st->map,
+				  AD7091R_REG_CH_HYSTERESIS(chan->channel),
+				  val);
+		if (ret)
+			return ret;
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int ad7091r_write_event_value(struct iio_dev *indio_dev,
+				     const struct iio_chan_spec *chan,
+				     enum iio_event_type type,
+				     enum iio_event_direction dir,
+				     enum iio_event_info info, int val, int val2)
+{
+	struct ad7091r_state *st = iio_priv(indio_dev);
+
+	switch (info) {
+	case IIO_EV_INFO_VALUE:
+		switch (dir) {
+		case IIO_EV_DIR_RISING:
+			return regmap_write(st->map,
+					    AD7091R_REG_CH_HIGH_LIMIT(chan->channel),
+					    val);
+		case IIO_EV_DIR_FALLING:
+			return regmap_write(st->map,
+					    AD7091R_REG_CH_LOW_LIMIT(chan->channel),
+					    val);
+		default:
+			return -EINVAL;
+		}
+	case IIO_EV_INFO_HYSTERESIS:
+		return regmap_write(st->map,
+				    AD7091R_REG_CH_HYSTERESIS(chan->channel),
+				    val);
+	default:
+		return -EINVAL;
+	}
+}
+
 static const struct iio_info ad7091r_info = {
 	.read_raw = ad7091r_read_raw,
+	.read_event_config = &ad7091r_read_event_config,
+	.write_event_config = &ad7091r_write_event_config,
+	.read_event_value = &ad7091r_read_event_value,
+	.write_event_value = &ad7091r_write_event_value,
 };
 
 static irqreturn_t ad7091r_event_handler(int irq, void *private)
 {
-	struct ad7091r_state *st = (struct ad7091r_state *) private;
-	struct iio_dev *iio_dev = dev_get_drvdata(st->dev);
+	struct iio_dev *iio_dev = private;
+	struct ad7091r_state *st = iio_priv(iio_dev);
 	unsigned int i, read_val;
 	int ret;
 	s64 timestamp = iio_get_time_ns(iio_dev);
@@ -232,9 +389,14 @@
 	iio_dev->channels = chip_info->channels;
 
 	if (irq) {
+		ret = regmap_update_bits(st->map, AD7091R_REG_CONF,
+					 AD7091R_REG_CONF_ALERT_EN, BIT(4));
+		if (ret)
+			return ret;
+
 		ret = devm_request_threaded_irq(dev, irq, NULL,
 				ad7091r_event_handler,
-				IRQF_TRIGGER_FALLING | IRQF_ONESHOT, name, st);
+				IRQF_TRIGGER_FALLING | IRQF_ONESHOT, name, iio_dev);
 		if (ret)
 			return ret;
 	}
@@ -243,7 +405,14 @@
 	if (IS_ERR(st->vref)) {
 		if (PTR_ERR(st->vref) == -EPROBE_DEFER)
 			return -EPROBE_DEFER;
+
 		st->vref = NULL;
+		/* Enable internal vref */
+		ret = regmap_set_bits(st->map, AD7091R_REG_CONF,
+				      AD7091R_REG_CONF_INT_VREF);
+		if (ret)
+			return dev_err_probe(st->dev, ret,
+					     "Error on enable internal reference\n");
 	} else {
 		ret = regulator_enable(st->vref);
 		if (ret)
@@ -260,7 +429,7 @@
 
 	return devm_iio_device_register(dev, iio_dev);
 }
-EXPORT_SYMBOL_GPL(ad7091r_probe);
+EXPORT_SYMBOL_NS_GPL(ad7091r_probe, IIO_AD7091R);
 
 static bool ad7091r_writeable_reg(struct device *dev, unsigned int reg)
 {
@@ -290,7 +459,7 @@
 	.writeable_reg = ad7091r_writeable_reg,
 	.volatile_reg = ad7091r_volatile_reg,
 };
-EXPORT_SYMBOL_GPL(ad7091r_regmap_config);
+EXPORT_SYMBOL_NS_GPL(ad7091r_regmap_config, IIO_AD7091R);
 
 MODULE_AUTHOR("Beniamin Bia <beniamin.bia@analog.com>");
 MODULE_DESCRIPTION("Analog Devices AD7091Rx multi-channel converters");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7091r-base.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7091r-base.h
@@ -8,6 +8,12 @@
 #ifndef __DRIVERS_IIO_ADC_AD7091R_BASE_H__
 #define __DRIVERS_IIO_ADC_AD7091R_BASE_H__
 
+#define AD7091R_REG_CONF_INT_VREF	BIT(0)
+
+/* AD7091R_REG_CH_LIMIT */
+#define AD7091R_HIGH_LIMIT		0xFFF
+#define AD7091R_LOW_LIMIT		0x0
+
 struct device;
 struct ad7091r_state;
 
@@ -17,6 +23,8 @@
 	unsigned int vref_mV;
 };
 
+extern const struct iio_event_spec ad7091r_events[3];
+
 extern const struct regmap_config ad7091r_regmap_config;
 
 int ad7091r_probe(struct device *dev, const char *name,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7091r5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7091r5.c
@@ -12,26 +12,6 @@
 
 #include "ad7091r-base.h"
 
-static const struct iio_event_spec ad7091r5_events[] = {
-	{
-		.type = IIO_EV_TYPE_THRESH,
-		.dir = IIO_EV_DIR_RISING,
-		.mask_separate = BIT(IIO_EV_INFO_VALUE) |
-				 BIT(IIO_EV_INFO_ENABLE),
-	},
-	{
-		.type = IIO_EV_TYPE_THRESH,
-		.dir = IIO_EV_DIR_FALLING,
-		.mask_separate = BIT(IIO_EV_INFO_VALUE) |
-				 BIT(IIO_EV_INFO_ENABLE),
-	},
-	{
-		.type = IIO_EV_TYPE_THRESH,
-		.dir = IIO_EV_DIR_EITHER,
-		.mask_separate = BIT(IIO_EV_INFO_HYSTERESIS),
-	},
-};
-
 #define AD7091R_CHANNEL(idx, bits, ev, num_ev) { \
 	.type = IIO_VOLTAGE, \
 	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
@@ -44,10 +24,10 @@
 	.scan_type.realbits = bits, \
 }
 static const struct iio_chan_spec ad7091r5_channels_irq[] = {
-	AD7091R_CHANNEL(0, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)),
-	AD7091R_CHANNEL(1, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)),
-	AD7091R_CHANNEL(2, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)),
-	AD7091R_CHANNEL(3, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)),
+	AD7091R_CHANNEL(0, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+	AD7091R_CHANNEL(1, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+	AD7091R_CHANNEL(2, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+	AD7091R_CHANNEL(3, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
 };
 
 static const struct iio_chan_spec ad7091r5_channels_noirq[] = {
@@ -111,3 +91,4 @@
 MODULE_AUTHOR("Beniamin Bia <beniamin.bia@analog.com>");
 MODULE_DESCRIPTION("Analog Devices AD7091R5 multi-channel ADC driver");
 MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_AD7091R);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7124.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7124.c
@@ -76,7 +76,7 @@
 #define AD7124_CONFIG_REF_SEL(x)	FIELD_PREP(AD7124_CONFIG_REF_SEL_MSK, x)
 #define AD7124_CONFIG_PGA_MSK		GENMASK(2, 0)
 #define AD7124_CONFIG_PGA(x)		FIELD_PREP(AD7124_CONFIG_PGA_MSK, x)
-#define AD7124_CONFIG_IN_BUFF_MSK	GENMASK(7, 6)
+#define AD7124_CONFIG_IN_BUFF_MSK	GENMASK(6, 5)
 #define AD7124_CONFIG_IN_BUFF(x)	FIELD_PREP(AD7124_CONFIG_IN_BUFF_MSK, x)
 
 /* AD7124_FILTER_X */
@@ -144,15 +144,22 @@
 struct ad7124_channel_config {
 	bool live;
 	unsigned int cfg_slot;
-	enum ad7124_ref_sel refsel;
-	bool bipolar;
-	bool buf_positive;
-	bool buf_negative;
-	unsigned int vref_mv;
-	unsigned int pga_bits;
-	unsigned int odr;
-	unsigned int odr_sel_bits;
-	unsigned int filter_type;
+	/*
+	 * Following fields are used to compare for equality. If you
+	 * make adaptations in it, you most likely also have to adapt
+	 * ad7124_find_similar_live_cfg(), too.
+	 */
+	struct_group(config_props,
+		enum ad7124_ref_sel refsel;
+		bool bipolar;
+		bool buf_positive;
+		bool buf_negative;
+		unsigned int vref_mv;
+		unsigned int pga_bits;
+		unsigned int odr;
+		unsigned int odr_sel_bits;
+		unsigned int filter_type;
+	);
 };
 
 struct ad7124_channel {
@@ -188,7 +195,6 @@
 		.sign = 'u',
 		.realbits = 24,
 		.storagebits = 32,
-		.shift = 8,
 		.endianness = IIO_BE,
 	},
 };
@@ -329,14 +335,38 @@
 								  struct ad7124_channel_config *cfg)
 {
 	struct ad7124_channel_config *cfg_aux;
-	ptrdiff_t cmp_size;
 	int i;
 
-	cmp_size = (u8 *)&cfg->live - (u8 *)cfg;
+	/*
+	 * This is just to make sure that the comparison is adapted after
+	 * struct ad7124_channel_config was changed.
+	 */
+	static_assert(sizeof_field(struct ad7124_channel_config, config_props) ==
+		      sizeof(struct {
+				     enum ad7124_ref_sel refsel;
+				     bool bipolar;
+				     bool buf_positive;
+				     bool buf_negative;
+				     unsigned int vref_mv;
+				     unsigned int pga_bits;
+				     unsigned int odr;
+				     unsigned int odr_sel_bits;
+				     unsigned int filter_type;
+			     }));
+
 	for (i = 0; i < st->num_channels; i++) {
 		cfg_aux = &st->channels[i].cfg;
 
-		if (cfg_aux->live && !memcmp(cfg, cfg_aux, cmp_size))
+		if (cfg_aux->live &&
+		    cfg->refsel == cfg_aux->refsel &&
+		    cfg->bipolar == cfg_aux->bipolar &&
+		    cfg->buf_positive == cfg_aux->buf_positive &&
+		    cfg->buf_negative == cfg_aux->buf_negative &&
+		    cfg->vref_mv == cfg_aux->vref_mv &&
+		    cfg->pga_bits == cfg_aux->pga_bits &&
+		    cfg->odr == cfg_aux->odr &&
+		    cfg->odr_sel_bits == cfg_aux->odr_sel_bits &&
+		    cfg->filter_type == cfg_aux->filter_type)
 			return cfg_aux;
 	}
 
@@ -593,7 +623,7 @@
 
 	switch (info) {
 	case IIO_CHAN_INFO_SAMP_FREQ:
-		if (val2 != 0) {
+		if (val2 != 0 || val == 0) {
 			ret = -EINVAL;
 			break;
 		}
@@ -687,6 +717,7 @@
 	if (ret < 0)
 		return ret;
 
+	fsleep(200);
 	timeout = 100;
 	do {
 		ret = ad_sd_read_reg(&st->sd, AD7124_STATUS, 1, &readval);
@@ -852,6 +883,9 @@
 		 * set all channels to this default value.
 		 */
 		ad7124_set_channel_odr(st, i, 10);
+
+		/* Disable all channels to prevent unintended conversions. */
+		ad_sd_write_reg(&st->sd, AD7124_CHANNEL(i), 2, 0);
 	}
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7192.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7192.c
@@ -177,6 +177,7 @@
 	const struct ad7192_chip_info	*chip_info;
 	struct regulator		*avdd;
 	struct regulator		*dvdd;
+	struct regulator		*vref;
 	struct clk			*mclk;
 	u16				int_vref_mv;
 	u32				fclk;
@@ -327,7 +328,7 @@
 	clock_sel = AD7192_CLK_INT;
 
 	/* use internal clock */
-	if (st->mclk) {
+	if (!st->mclk) {
 		if (of_property_read_bool(np, "adi,int-clock-output-enable"))
 			clock_sel = AD7192_CLK_INT_CO;
 	} else {
@@ -340,9 +341,9 @@
 	return clock_sel;
 }
 
-static int ad7192_setup(struct ad7192_state *st, struct device_node *np)
+static int ad7192_setup(struct iio_dev *indio_dev, struct device_node *np)
 {
-	struct iio_dev *indio_dev = spi_get_drvdata(st->sd.spi);
+	struct ad7192_state *st = iio_priv(indio_dev);
 	bool rej60_en, refin2_en;
 	bool buf_en, bipolar, burnout_curr_en;
 	unsigned long long scale_uv;
@@ -835,10 +836,6 @@
 	__AD719x_CHANNEL(_si, _channel1, -1, _address, NULL, IIO_VOLTAGE, \
 		BIT(IIO_CHAN_INFO_SCALE), ad7192_calibsys_ext_info)
 
-#define AD719x_SHORTED_CHANNEL(_si, _channel1, _address) \
-	__AD719x_CHANNEL(_si, _channel1, -1, _address, "shorted", IIO_VOLTAGE, \
-		BIT(IIO_CHAN_INFO_SCALE), ad7192_calibsys_ext_info)
-
 #define AD719x_TEMP_CHANNEL(_si, _address) \
 	__AD719x_CHANNEL(_si, 0, -1, _address, NULL, IIO_TEMP, 0, NULL)
 
@@ -846,7 +843,7 @@
 	AD719x_DIFF_CHANNEL(0, 1, 2, AD7192_CH_AIN1P_AIN2M),
 	AD719x_DIFF_CHANNEL(1, 3, 4, AD7192_CH_AIN3P_AIN4M),
 	AD719x_TEMP_CHANNEL(2, AD7192_CH_TEMP),
-	AD719x_SHORTED_CHANNEL(3, 2, AD7192_CH_AIN2P_AIN2M),
+	AD719x_DIFF_CHANNEL(3, 2, 2, AD7192_CH_AIN2P_AIN2M),
 	AD719x_CHANNEL(4, 1, AD7192_CH_AIN1),
 	AD719x_CHANNEL(5, 2, AD7192_CH_AIN2),
 	AD719x_CHANNEL(6, 3, AD7192_CH_AIN3),
@@ -860,7 +857,7 @@
 	AD719x_DIFF_CHANNEL(2, 5, 6, AD7193_CH_AIN5P_AIN6M),
 	AD719x_DIFF_CHANNEL(3, 7, 8, AD7193_CH_AIN7P_AIN8M),
 	AD719x_TEMP_CHANNEL(4, AD7193_CH_TEMP),
-	AD719x_SHORTED_CHANNEL(5, 2, AD7193_CH_AIN2P_AIN2M),
+	AD719x_DIFF_CHANNEL(5, 2, 2, AD7193_CH_AIN2P_AIN2M),
 	AD719x_CHANNEL(6, 1, AD7193_CH_AIN1),
 	AD719x_CHANNEL(7, 2, AD7193_CH_AIN2),
 	AD719x_CHANNEL(8, 3, AD7193_CH_AIN3),
@@ -966,10 +963,30 @@
 	if (ret)
 		return ret;
 
-	ret = regulator_get_voltage(st->avdd);
-	if (ret < 0) {
-		dev_err(&spi->dev, "Device tree error, reference voltage undefined\n");
-		return ret;
+	st->vref = devm_regulator_get_optional(&spi->dev, "vref");
+	if (IS_ERR(st->vref)) {
+		if (PTR_ERR(st->vref) != -ENODEV)
+			return PTR_ERR(st->vref);
+
+		ret = regulator_get_voltage(st->avdd);
+		if (ret < 0)
+			return dev_err_probe(&spi->dev, ret,
+					     "Device tree error, AVdd voltage undefined\n");
+	} else {
+		ret = regulator_enable(st->vref);
+		if (ret) {
+			dev_err(&spi->dev, "Failed to enable specified Vref supply\n");
+			return ret;
+		}
+
+		ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, st->vref);
+		if (ret)
+			return ret;
+
+		ret = regulator_get_voltage(st->vref);
+		if (ret < 0)
+			return dev_err_probe(&spi->dev, ret,
+					     "Device tree error, Vref voltage undefined\n");
 	}
 	st->int_vref_mv = ret / 1000;
 
@@ -1019,7 +1036,7 @@
 		}
 	}
 
-	ret = ad7192_setup(st, spi->dev.of_node);
+	ret = ad7192_setup(indio_dev, spi->dev.of_node);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7266.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7266.c
@@ -157,6 +157,8 @@
 		ret = ad7266_read_single(st, val, chan->address);
 		iio_device_release_direct_mode(indio_dev);
 
+		if (ret < 0)
+			return ret;
 		*val = (*val >> 2) & 0xfff;
 		if (chan->scan_type.sign == 's')
 			*val = sign_extend32(*val, 11);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7292.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7292.c
@@ -287,10 +287,8 @@
 
 		ret = devm_add_action_or_reset(&spi->dev,
 					       ad7292_regulator_disable, st);
-		if (ret) {
-			regulator_disable(st->reg);
+		if (ret)
 			return ret;
-		}
 
 		ret = regulator_get_voltage(st->reg);
 		if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7606.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7606.c
@@ -238,9 +238,9 @@
 	struct ad7606_state *st = iio_priv(indio_dev);
 	DECLARE_BITMAP(values, 3);
 
-	values[0] = val;
+	values[0] = val & GENMASK(2, 0);
 
-	gpiod_set_array_value(ARRAY_SIZE(values), st->gpio_os->desc,
+	gpiod_set_array_value(st->gpio_os->ndescs, st->gpio_os->desc,
 			      st->gpio_os->info, values);
 
 	/* AD7616 requires a reset to update value */
@@ -445,7 +445,7 @@
 		return PTR_ERR(st->gpio_range);
 
 	st->gpio_standby = devm_gpiod_get_optional(dev, "standby",
-						   GPIOD_OUT_HIGH);
+						   GPIOD_OUT_LOW);
 	if (IS_ERR(st->gpio_standby))
 		return PTR_ERR(st->gpio_standby);
 
@@ -704,7 +704,7 @@
 
 	if (st->gpio_standby) {
 		gpiod_set_value(st->gpio_range, 1);
-		gpiod_set_value(st->gpio_standby, 0);
+		gpiod_set_value(st->gpio_standby, 1);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7606_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7606_spi.c
@@ -249,8 +249,9 @@
 static int ad7606B_sw_mode_config(struct iio_dev *indio_dev)
 {
 	struct ad7606_state *st = iio_priv(indio_dev);
-	unsigned long os[3] = {1};
+	DECLARE_BITMAP(os, 3);
 
+	bitmap_fill(os, 3);
 	/*
 	 * Software mode is enabled when all three oversampling
 	 * pins are set to high. If oversampling gpios are defined
@@ -258,7 +259,7 @@
 	 * otherwise, they must be hardwired to VDD
 	 */
 	if (st->gpio_os) {
-		gpiod_set_array_value(ARRAY_SIZE(os),
+		gpiod_set_array_value(st->gpio_os->ndescs,
 				      st->gpio_os->desc, st->gpio_os->info, os);
 	}
 	/* OS of 128 and 256 are available only in software mode */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7768-1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7768-1.c
@@ -480,8 +480,8 @@
 	iio_push_to_buffers_with_timestamp(indio_dev, &st->data.scan,
 					   iio_get_time_ns(indio_dev));
 
-	iio_trigger_notify_done(indio_dev->trig);
 err_unlock:
+	iio_trigger_notify_done(indio_dev->trig);
 	mutex_unlock(&st->lock);
 
 	return IRQ_HANDLED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7780.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7780.c
@@ -152,7 +152,7 @@
 
 	switch (m) {
 	case IIO_CHAN_INFO_SCALE:
-		if (val != 0)
+		if (val != 0 || val2 == 0)
 			return -EINVAL;
 
 		vref = st->int_vref_mv * 1000000LL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7791.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7791.c
@@ -253,7 +253,7 @@
 	.has_registers = true,
 	.addr_shift = 4,
 	.read_mask = BIT(3),
-	.irq_flags = IRQF_TRIGGER_LOW,
+	.irq_flags = IRQF_TRIGGER_FALLING,
 };
 
 static int ad7791_read_raw(struct iio_dev *indio_dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad7923.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad7923.c
@@ -93,6 +93,7 @@
 			.sign = 'u',					\
 			.realbits = (bits),				\
 			.storagebits = 16,				\
+			.shift = 12 - (bits),				\
 			.endianness = IIO_BE,				\
 		},							\
 	}
@@ -268,7 +269,8 @@
 			return ret;
 
 		if (chan->address == EXTRACT(ret, 12, 4))
-			*val = EXTRACT(ret, 0, 12);
+			*val = EXTRACT(ret, chan->scan_type.shift,
+				       chan->scan_type.realbits);
 		else
 			return -EIO;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad9467.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad9467.c
@@ -119,9 +119,9 @@
 	struct spi_device		*spi;
 	struct clk			*clk;
 	unsigned int			output_mode;
+	unsigned int                    (*scales)[2];
 
 	struct gpio_desc		*pwrdown_gpio;
-	struct gpio_desc		*reset_gpio;
 };
 
 static int ad9467_spi_read(struct spi_device *spi, unsigned int reg)
@@ -163,9 +163,10 @@
 
 	if (readval == NULL) {
 		ret = ad9467_spi_write(spi, reg, writeval);
-		ad9467_spi_write(spi, AN877_ADC_REG_TRANSFER,
-				 AN877_ADC_TRANSFER_SYNC);
-		return ret;
+		if (ret)
+			return ret;
+		return ad9467_spi_write(spi, AN877_ADC_REG_TRANSFER,
+					AN877_ADC_TRANSFER_SYNC);
 	}
 
 	ret = ad9467_spi_read(spi, reg);
@@ -212,6 +213,7 @@
 	.channel = _chan,						\
 	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |		\
 		BIT(IIO_CHAN_INFO_SAMP_FREQ),				\
+	.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE), \
 	.scan_index = _si,						\
 	.scan_type = {							\
 		.sign = _sign,						\
@@ -221,11 +223,11 @@
 }
 
 static const struct iio_chan_spec ad9434_channels[] = {
-	AD9467_CHAN(0, 0, 12, 'S'),
+	AD9467_CHAN(0, 0, 12, 's'),
 };
 
 static const struct iio_chan_spec ad9467_channels[] = {
-	AD9467_CHAN(0, 0, 16, 'S'),
+	AD9467_CHAN(0, 0, 16, 's'),
 };
 
 static const struct ad9467_chip_info ad9467_chip_tbl[] = {
@@ -273,10 +275,13 @@
 	const struct ad9467_chip_info *info1 = to_ad9467_chip_info(info);
 	struct ad9467_state *st = adi_axi_adc_conv_priv(conv);
 	unsigned int i, vref_val;
+	int ret;
 
-	vref_val = ad9467_spi_read(st->spi, AN877_ADC_REG_VREF);
+	ret = ad9467_spi_read(st->spi, AN877_ADC_REG_VREF);
+	if (ret < 0)
+		return ret;
 
-	vref_val &= info1->vref_mask;
+	vref_val = ret & info1->vref_mask;
 
 	for (i = 0; i < info->num_scales; i++) {
 		if (vref_val == info->scale_table[i][1])
@@ -297,6 +302,7 @@
 	struct ad9467_state *st = adi_axi_adc_conv_priv(conv);
 	unsigned int scale_val[2];
 	unsigned int i;
+	int ret;
 
 	if (val != 0)
 		return -EINVAL;
@@ -306,11 +312,13 @@
 		if (scale_val[0] != val || scale_val[1] != val2)
 			continue;
 
-		ad9467_spi_write(st->spi, AN877_ADC_REG_VREF,
-				 info->scale_table[i][1]);
-		ad9467_spi_write(st->spi, AN877_ADC_REG_TRANSFER,
-				 AN877_ADC_TRANSFER_SYNC);
-		return 0;
+		ret = ad9467_spi_write(st->spi, AN877_ADC_REG_VREF,
+				       info->scale_table[i][1]);
+		if (ret < 0)
+			return ret;
+
+		return ad9467_spi_write(st->spi, AN877_ADC_REG_TRANSFER,
+					AN877_ADC_TRANSFER_SYNC);
 	}
 
 	return -EINVAL;
@@ -359,6 +367,26 @@
 	}
 }
 
+static int ad9467_read_avail(struct adi_axi_adc_conv *conv,
+			     struct iio_chan_spec const *chan,
+			     const int **vals, int *type, int *length,
+			     long mask)
+{
+	const struct adi_axi_adc_chip_info *info = conv->chip_info;
+	struct ad9467_state *st = adi_axi_adc_conv_priv(conv);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		*vals = (const int *)st->scales;
+		*type = IIO_VAL_INT_PLUS_MICRO;
+		/* Values are stored in a 2D matrix */
+		*length = info->num_scales * 2;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
 static int ad9467_outputmode_set(struct spi_device *spi, unsigned int mode)
 {
 	int ret;
@@ -371,6 +399,26 @@
 				AN877_ADC_TRANSFER_SYNC);
 }
 
+static int ad9467_scale_fill(struct adi_axi_adc_conv *conv)
+{
+	const struct adi_axi_adc_chip_info *info = conv->chip_info;
+	struct ad9467_state *st = adi_axi_adc_conv_priv(conv);
+	unsigned int i, val1, val2;
+
+	st->scales = devm_kmalloc_array(&st->spi->dev, info->num_scales,
+					sizeof(*st->scales), GFP_KERNEL);
+	if (!st->scales)
+		return -ENOMEM;
+
+	for (i = 0; i < info->num_scales; i++) {
+		__ad9467_get_scale(conv, i, &val1, &val2);
+		st->scales[i][0] = val1;
+		st->scales[i][1] = val2;
+	}
+
+	return 0;
+}
+
 static int ad9467_preenable_setup(struct adi_axi_adc_conv *conv)
 {
 	struct ad9467_state *st = adi_axi_adc_conv_priv(conv);
@@ -378,11 +426,19 @@
 	return ad9467_outputmode_set(st->spi, st->output_mode);
 }
 
-static void ad9467_clk_disable(void *data)
+static int ad9467_reset(struct device *dev)
 {
-	struct ad9467_state *st = data;
+	struct gpio_desc *gpio;
+
+	gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR_OR_NULL(gpio))
+		return PTR_ERR_OR_ZERO(gpio);
+
+	fsleep(1);
+	gpiod_set_value_cansleep(gpio, 0);
+	fsleep(10 * USEC_PER_MSEC);
 
-	clk_disable_unprepare(st->clk);
+	return 0;
 }
 
 static int ad9467_probe(struct spi_device *spi)
@@ -404,38 +460,25 @@
 	st = adi_axi_adc_conv_priv(conv);
 	st->spi = spi;
 
-	st->clk = devm_clk_get(&spi->dev, "adc-clk");
+	st->clk = devm_clk_get_enabled(&spi->dev, "adc-clk");
 	if (IS_ERR(st->clk))
 		return PTR_ERR(st->clk);
 
-	ret = clk_prepare_enable(st->clk);
-	if (ret < 0)
-		return ret;
-
-	ret = devm_add_action_or_reset(&spi->dev, ad9467_clk_disable, st);
-	if (ret)
-		return ret;
-
 	st->pwrdown_gpio = devm_gpiod_get_optional(&spi->dev, "powerdown",
 						   GPIOD_OUT_LOW);
 	if (IS_ERR(st->pwrdown_gpio))
 		return PTR_ERR(st->pwrdown_gpio);
 
-	st->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset",
-						 GPIOD_OUT_LOW);
-	if (IS_ERR(st->reset_gpio))
-		return PTR_ERR(st->reset_gpio);
-
-	if (st->reset_gpio) {
-		udelay(1);
-		ret = gpiod_direction_output(st->reset_gpio, 1);
-		if (ret)
-			return ret;
-		mdelay(10);
-	}
+	ret = ad9467_reset(&spi->dev);
+	if (ret)
+		return ret;
 
 	conv->chip_info = &info->axi_adc_info;
 
+	ret = ad9467_scale_fill(conv);
+	if (ret)
+		return ret;
+
 	id = ad9467_spi_read(spi, AN877_ADC_REG_CHIP_ID);
 	if (id != conv->chip_info->id) {
 		dev_err(&spi->dev, "Mismatch CHIP_ID, got 0x%X, expected 0x%X\n",
@@ -446,6 +489,7 @@
 	conv->reg_access = ad9467_reg_access;
 	conv->write_raw = ad9467_write_raw;
 	conv->read_raw = ad9467_read_raw;
+	conv->read_avail = ad9467_read_avail;
 	conv->preenable_setup = ad9467_preenable_setup;
 
 	st->output_mode = info->default_output_mode |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ad_sigma_delta.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ad_sigma_delta.c
@@ -280,10 +280,10 @@
 	unsigned int data_reg;
 	int ret = 0;
 
-	if (iio_buffer_enabled(indio_dev))
-		return -EBUSY;
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
 
-	mutex_lock(&indio_dev->mlock);
 	ad_sigma_delta_set_channel(sigma_delta, chan->address);
 
 	spi_bus_lock(sigma_delta->spi->master);
@@ -322,7 +322,7 @@
 	ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_IDLE);
 	sigma_delta->bus_locked = false;
 	spi_bus_unlock(sigma_delta->spi->master);
-	mutex_unlock(&indio_dev->mlock);
+	iio_device_release_direct_mode(indio_dev);
 
 	if (ret)
 		return ret;
@@ -490,6 +490,10 @@
 	init_completion(&sigma_delta->completion);
 
 	sigma_delta->irq_dis = true;
+
+	/* the IRQ core clears IRQ_DISABLE_UNLAZY flag when freeing an IRQ */
+	irq_set_status_flags(sigma_delta->spi->irq, IRQ_DISABLE_UNLAZY);
+
 	ret = devm_request_irq(dev, sigma_delta->spi->irq,
 			       ad_sd_data_rdy_trig_poll,
 			       sigma_delta->info->irq_flags | IRQF_NO_AUTOEN,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/adi-axi-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/adi-axi-adc.c
@@ -142,6 +142,20 @@
 	return conv->write_raw(conv, chan, val, val2, mask);
 }
 
+static int adi_axi_adc_read_avail(struct iio_dev *indio_dev,
+				  struct iio_chan_spec const *chan,
+				  const int **vals, int *type, int *length,
+				  long mask)
+{
+	struct adi_axi_adc_state *st = iio_priv(indio_dev);
+	struct adi_axi_adc_conv *conv = &st->client->conv;
+
+	if (!conv->read_avail)
+		return -EOPNOTSUPP;
+
+	return conv->read_avail(conv, chan, vals, type, length, mask);
+}
+
 static int adi_axi_adc_update_scan_mode(struct iio_dev *indio_dev,
 					const unsigned long *scan_mask)
 {
@@ -226,69 +240,11 @@
 }
 EXPORT_SYMBOL_GPL(devm_adi_axi_adc_conv_register);
 
-static ssize_t in_voltage_scale_available_show(struct device *dev,
-					       struct device_attribute *attr,
-					       char *buf)
-{
-	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
-	struct adi_axi_adc_state *st = iio_priv(indio_dev);
-	struct adi_axi_adc_conv *conv = &st->client->conv;
-	size_t len = 0;
-	int i;
-
-	for (i = 0; i < conv->chip_info->num_scales; i++) {
-		const unsigned int *s = conv->chip_info->scale_table[i];
-
-		len += scnprintf(buf + len, PAGE_SIZE - len,
-				 "%u.%06u ", s[0], s[1]);
-	}
-	buf[len - 1] = '\n';
-
-	return len;
-}
-
-static IIO_DEVICE_ATTR_RO(in_voltage_scale_available, 0);
-
-enum {
-	ADI_AXI_ATTR_SCALE_AVAIL,
-};
-
-#define ADI_AXI_ATTR(_en_, _file_)			\
-	[ADI_AXI_ATTR_##_en_] = &iio_dev_attr_##_file_.dev_attr.attr
-
-static struct attribute *adi_axi_adc_attributes[] = {
-	ADI_AXI_ATTR(SCALE_AVAIL, in_voltage_scale_available),
-	NULL
-};
-
-static umode_t axi_adc_attr_is_visible(struct kobject *kobj,
-				       struct attribute *attr, int n)
-{
-	struct device *dev = kobj_to_dev(kobj);
-	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
-	struct adi_axi_adc_state *st = iio_priv(indio_dev);
-	struct adi_axi_adc_conv *conv = &st->client->conv;
-
-	switch (n) {
-	case ADI_AXI_ATTR_SCALE_AVAIL:
-		if (!conv->chip_info->num_scales)
-			return 0;
-		return attr->mode;
-	default:
-		return attr->mode;
-	}
-}
-
-static const struct attribute_group adi_axi_adc_attribute_group = {
-	.attrs = adi_axi_adc_attributes,
-	.is_visible = axi_adc_attr_is_visible,
-};
-
 static const struct iio_info adi_axi_adc_info = {
 	.read_raw = &adi_axi_adc_read_raw,
 	.write_raw = &adi_axi_adc_write_raw,
-	.attrs = &adi_axi_adc_attribute_group,
 	.update_scan_mode = &adi_axi_adc_update_scan_mode,
+	.read_avail = &adi_axi_adc_read_avail,
 };
 
 static const struct adi_axi_adc_core_info adi_axi_adc_10_0_a_info = {
@@ -322,16 +278,19 @@
 
 		if (!try_module_get(cl->dev->driver->owner)) {
 			mutex_unlock(&registered_clients_lock);
+			of_node_put(cln);
 			return ERR_PTR(-ENODEV);
 		}
 
 		get_device(cl->dev);
 		cl->info = info;
 		mutex_unlock(&registered_clients_lock);
+		of_node_put(cln);
 		return cl;
 	}
 
 	mutex_unlock(&registered_clients_lock);
+	of_node_put(cln);
 
 	return ERR_PTR(-EPROBE_DEFER);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/at91-sama5d2_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/at91-sama5d2_adc.c
@@ -74,7 +74,7 @@
 #define	AT91_SAMA5D2_MR_ANACH		BIT(23)
 /* Tracking Time */
 #define	AT91_SAMA5D2_MR_TRACKTIM(v)	((v) << 24)
-#define	AT91_SAMA5D2_MR_TRACKTIM_MAX	0xff
+#define	AT91_SAMA5D2_MR_TRACKTIM_MAX	0xf
 /* Transfer Time */
 #define	AT91_SAMA5D2_MR_TRANSFER(v)	((v) << 28)
 #define	AT91_SAMA5D2_MR_TRANSFER_MAX	0x3
@@ -894,7 +894,7 @@
 		return at91_adc_configure_touch(st, true);
 
 	/* if we are not in triggered mode, we cannot enable the buffer. */
-	if (!(indio_dev->currentmode & INDIO_ALL_TRIGGERED_MODES))
+	if (!(iio_device_get_current_mode(indio_dev) & INDIO_ALL_TRIGGERED_MODES))
 		return -EINVAL;
 
 	/* we continue with the triggered buffer */
@@ -947,7 +947,7 @@
 		return at91_adc_configure_touch(st, false);
 
 	/* if we are not in triggered mode, nothing to do here */
-	if (!(indio_dev->currentmode & INDIO_ALL_TRIGGERED_MODES))
+	if (!(iio_device_get_current_mode(indio_dev) & INDIO_ALL_TRIGGERED_MODES))
 		return -EINVAL;
 
 	/*
@@ -1000,7 +1000,7 @@
 	trig = devm_iio_trigger_alloc(&indio->dev, "%s-dev%d-%s", indio->name,
 				iio_device_id(indio), trigger_name);
 	if (!trig)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	trig->dev.parent = indio->dev.parent;
 	iio_trigger_set_drvdata(trig, indio);
@@ -1329,10 +1329,12 @@
 		ret = at91_adc_read_position(st, chan->channel,
 					     &tmp_val);
 		*val = tmp_val;
+		if (ret > 0)
+			ret = at91_adc_adjust_val_osr(st, val);
 		mutex_unlock(&st->lock);
 		iio_device_release_direct_mode(indio_dev);
 
-		return at91_adc_adjust_val_osr(st, val);
+		return ret;
 	}
 	if (chan->type == IIO_PRESSURE) {
 		ret = iio_device_claim_direct_mode(indio_dev);
@@ -1343,10 +1345,12 @@
 		ret = at91_adc_read_pressure(st, chan->channel,
 					     &tmp_val);
 		*val = tmp_val;
+		if (ret > 0)
+			ret = at91_adc_adjust_val_osr(st, val);
 		mutex_unlock(&st->lock);
 		iio_device_release_direct_mode(indio_dev);
 
-		return at91_adc_adjust_val_osr(st, val);
+		return ret;
 	}
 
 	/* in this case we have a voltage channel */
@@ -1377,7 +1381,8 @@
 		*val = st->conversion_value;
 		ret = at91_adc_adjust_val_osr(st, val);
 		if (chan->scan_type.sign == 's')
-			*val = sign_extend32(*val, 11);
+			*val = sign_extend32(*val,
+					     chan->scan_type.realbits - 1);
 		st->conversion_done = false;
 	}
 
@@ -1436,16 +1441,20 @@
 		/* if no change, optimize out */
 		if (val == st->oversampling_ratio)
 			return 0;
+		mutex_lock(&st->lock);
 		st->oversampling_ratio = val;
 		/* update ratio */
 		at91_adc_config_emr(st);
+		mutex_unlock(&st->lock);
 		return 0;
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		if (val < st->soc_info.min_sample_rate ||
 		    val > st->soc_info.max_sample_rate)
 			return -EINVAL;
 
+		mutex_lock(&st->lock);
 		at91_adc_setup_samp_freq(indio_dev, val);
+		mutex_unlock(&st->lock);
 		return 0;
 	default:
 		return -EINVAL;
@@ -1894,6 +1903,9 @@
 	struct iio_dev *indio_dev = dev_get_drvdata(dev);
 	struct at91_adc_state *st = iio_priv(indio_dev);
 
+	if (iio_buffer_enabled(indio_dev))
+		at91_adc_buffer_postdisable(indio_dev);
+
 	/*
 	 * Do a sofware reset of the ADC before we go to suspend.
 	 * this will ensure that all pins are free from being muxed by the ADC
@@ -1937,14 +1949,11 @@
 	if (!iio_buffer_enabled(indio_dev))
 		return 0;
 
-	/* check if we are enabling triggered buffer or the touchscreen */
-	if (at91_adc_current_chan_is_touch(indio_dev))
-		return at91_adc_configure_touch(st, true);
-	else
-		return at91_adc_configure_trigger(st->trig, true);
+	ret = at91_adc_buffer_prepare(indio_dev);
+	if (ret)
+		goto vref_disable_resume;
 
-	/* not needed but more explicit */
-	return 0;
+	return at91_adc_configure_trigger(st->trig, true);
 
 vref_disable_resume:
 	regulator_disable(st->vref);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/at91_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/at91_adc.c
@@ -634,8 +634,10 @@
 	trig->ops = &at91_adc_trigger_ops;
 
 	ret = iio_trigger_register(trig);
-	if (ret)
+	if (ret) {
+		iio_trigger_free(trig);
 		return NULL;
+	}
 
 	return trig;
 }
@@ -983,7 +985,7 @@
 	return ret;
 
 err:
-	input_free_device(st->ts_input);
+	input_free_device(input);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/axp20x_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/axp20x_adc.c
@@ -251,19 +251,8 @@
 			  struct iio_chan_spec const *chan, int *val)
 {
 	struct axp20x_adc_iio *info = iio_priv(indio_dev);
-	int size;
 
-	/*
-	 * N.B.: Unlike the Chinese datasheets tell, the charging current is
-	 * stored on 12 bits, not 13 bits. Only discharging current is on 13
-	 * bits.
-	 */
-	if (chan->type == IIO_CURRENT && chan->channel == AXP22X_BATT_DISCHRG_I)
-		size = 13;
-	else
-		size = 12;
-
-	*val = axp20x_read_variable_width(info->regmap, chan->address, size);
+	*val = axp20x_read_variable_width(info->regmap, chan->address, 12);
 	if (*val < 0)
 		return *val;
 
@@ -386,9 +375,8 @@
 		return IIO_VAL_INT_PLUS_MICRO;
 
 	case IIO_CURRENT:
-		*val = 0;
-		*val2 = 500000;
-		return IIO_VAL_INT_PLUS_MICRO;
+		*val = 1;
+		return IIO_VAL_INT;
 
 	case IIO_TEMP:
 		*val = 100;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/axp288_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/axp288_adc.c
@@ -196,6 +196,14 @@
 		},
 		.driver_data = (void *)(uintptr_t)AXP288_ADC_TS_BIAS_80UA,
 	},
+	{
+		/* Nuvision Solo 10 Draw */
+		.matches = {
+		  DMI_MATCH(DMI_SYS_VENDOR, "TMAX"),
+		  DMI_MATCH(DMI_PRODUCT_NAME, "TM101W610L"),
+		},
+		.driver_data = (void *)(uintptr_t)AXP288_ADC_TS_BIAS_80UA,
+	},
 	{}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/berlin2-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/berlin2-adc.c
@@ -289,8 +289,10 @@
 	int ret;
 
 	indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
-	if (!indio_dev)
+	if (!indio_dev) {
+		of_node_put(parent_np);
 		return -ENOMEM;
+	}
 
 	priv = iio_priv(indio_dev);
 	platform_set_drvdata(pdev, indio_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/dln2-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/dln2-adc.c
@@ -248,7 +248,6 @@
 static int dln2_adc_read(struct dln2_adc *dln2, unsigned int channel)
 {
 	int ret, i;
-	struct iio_dev *indio_dev = platform_get_drvdata(dln2->pdev);
 	u16 conflict;
 	__le16 value;
 	int olen = sizeof(value);
@@ -257,13 +256,9 @@
 		.chan = channel,
 	};
 
-	ret = iio_device_claim_direct_mode(indio_dev);
-	if (ret < 0)
-		return ret;
-
 	ret = dln2_adc_set_chan_enabled(dln2, channel, true);
 	if (ret < 0)
-		goto release_direct;
+		return ret;
 
 	ret = dln2_adc_set_port_enabled(dln2, true, &conflict);
 	if (ret < 0) {
@@ -300,8 +295,6 @@
 	dln2_adc_set_port_enabled(dln2, false, NULL);
 disable_chan:
 	dln2_adc_set_chan_enabled(dln2, channel, false);
-release_direct:
-	iio_device_release_direct_mode(indio_dev);
 
 	return ret;
 }
@@ -337,10 +330,16 @@
 
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
+		ret = iio_device_claim_direct_mode(indio_dev);
+		if (ret < 0)
+			return ret;
+
 		mutex_lock(&dln2->mutex);
 		ret = dln2_adc_read(dln2, chan->channel);
 		mutex_unlock(&dln2->mutex);
 
+		iio_device_release_direct_mode(indio_dev);
+
 		if (ret < 0)
 			return ret;
 
@@ -656,7 +655,11 @@
 		return -ENOMEM;
 	}
 	iio_trigger_set_drvdata(dln2->trig, dln2);
-	devm_iio_trigger_register(dev, dln2->trig);
+	ret = devm_iio_trigger_register(dev, dln2->trig);
+	if (ret) {
+		dev_err(dev, "failed to register trigger: %d\n", ret);
+		return ret;
+	}
 	iio_trigger_set_immutable(indio_dev, dln2->trig);
 
 	ret = devm_iio_triggered_buffer_setup(dev, indio_dev, NULL,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/exynos_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/exynos_adc.c
@@ -826,16 +826,26 @@
 		}
 	}
 
+	/* leave out any TS related code if unreachable */
+	if (IS_REACHABLE(CONFIG_INPUT)) {
+		has_ts = of_property_read_bool(pdev->dev.of_node,
+					       "has-touchscreen") || pdata;
+	}
+
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
 		return irq;
 	info->irq = irq;
 
-	irq = platform_get_irq(pdev, 1);
-	if (irq == -EPROBE_DEFER)
-		return irq;
-
-	info->tsirq = irq;
+	if (has_ts) {
+		irq = platform_get_irq(pdev, 1);
+		if (irq == -EPROBE_DEFER)
+			return irq;
+
+		info->tsirq = irq;
+	} else {
+		info->tsirq = -1;
+	}
 
 	info->dev = &pdev->dev;
 
@@ -900,12 +910,6 @@
 	if (info->data->init_hw)
 		info->data->init_hw(info);
 
-	/* leave out any TS related code if unreachable */
-	if (IS_REACHABLE(CONFIG_INPUT)) {
-		has_ts = of_property_read_bool(pdev->dev.of_node,
-					       "has-touchscreen") || pdata;
-	}
-
 	if (pdata)
 		info->delay = pdata->delay;
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ina260-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ina260-adc.c
@@ -0,0 +1,554 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * INA260 power monitor driver
+ * Based on drivers/iio/adc/ina2xx-adc.c
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/kfifo_buf.h>
+#include <linux/iio/sysfs.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/sched/task.h>
+#include <linux/util_macros.h>
+
+/* INA260 registers definition */
+#define INA260_CONFIG		0x00
+#define INA260_CURRENT		0x01
+#define INA260_VOLTAGE		0x02
+#define INA260_POWER		0x03
+#define INA260_MASK_ENABLE	0x06
+#define INA260_ALERT_LIMIT	0x07
+#define INA260_MANF_ID		0xFE
+#define INA260_DIE_ID		0xFF
+
+#define INA260_CONFIG_DEFAULT	0x6327
+
+#define INA260_CURRENT_LSB	1250
+#define INA260_VOLTAGE_LSB	1250
+#define INA260_POWER_LSB	10
+
+/* Bits */
+#define INA260_CVRF		BIT(3)
+
+#define INA260_MODE_MASK	GENMASK(2, 0)
+#define INA260_VOLT_MASK	GENMASK(8, 6)
+#define INA260_SHIFT_VOLT(val)	((val) << 6)
+#define INA260_CURR_MASK	GENMASK(5, 3)
+#define INA260_SHIFT_CURR(val)	((val) << 3)
+#define INA260_AVG_MASK		GENMASK(11, 9)
+#define INA260_SHIFT_AVG(val)	((val) << 9)
+
+#define SAMPLING_PERIOD(x) ({		\
+	typeof(x) _x = (x);		\
+	(_x->config->volt_conv_time	\
+	+ _x->config->curr_conv_time)	\
+	* _x->config->avgs; })
+
+static bool ina260_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	return (reg == INA260_CONFIG) || (reg == INA260_MASK_ENABLE) ||
+		(reg == INA260_ALERT_LIMIT);
+}
+
+static bool ina260_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	return (reg != INA260_CONFIG);
+}
+
+static inline bool is_signed_reg(unsigned int reg)
+{
+	return (reg == INA260_CURRENT);
+}
+
+static const struct regmap_config ina260_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+	.max_register = 8,
+	.writeable_reg = ina260_is_writeable_reg,
+	.volatile_reg = ina260_is_volatile_reg,
+};
+
+enum ina260_ids {ina260 = 0};
+
+/**
+ * struct ina260_config - For configurable parameters
+ * @config_default: Default configuration
+ * @volt_conv_time: Bus voltage conversion time
+ * @curr_conv_time: Shunt current conversion time
+ * @avgs: Number of samples collected and averaged
+ */
+struct ina260_config {
+	u16 config_default;
+	int volt_conv_time;
+	int curr_conv_time;
+	int avgs;
+};
+
+/**
+ * struct ina260_chip - For device specific data
+ * @regmap: Regmap pointer to device registers
+ * @task: Pointer to task created by buffer mode
+ * @lock: Mutex to enable use of multiple user apps
+ * @chip_id: Id to determine chip
+ * @config: Pointer to config structure
+ */
+struct ina260_chip {
+	struct regmap *regmap;
+	struct task_struct *task;
+	struct mutex lock; /* Lock for device writes */
+	enum ina260_ids chip_id;
+	struct ina260_config *config;
+};
+
+static struct ina260_config ina260_config[] = {
+	[ina260] = {
+		.config_default = INA260_CONFIG_DEFAULT,
+		.volt_conv_time = 1100,
+		.curr_conv_time = 1100,
+		.avgs = 4,
+	},
+};
+
+static int ina260_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long mask)
+{
+	struct ina260_chip *chip = iio_priv(indio_dev);
+	unsigned int regval;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		if (iio_buffer_enabled(indio_dev))
+			return -EBUSY;
+
+		ret = regmap_read(chip->regmap, chan->address, &regval);
+		if (ret)
+			return ret;
+
+		if (is_signed_reg(chan->address))
+			*val = (s16)regval;
+		else
+			*val = regval;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->address) {
+		case INA260_CURRENT:
+			*val = INA260_CURRENT_LSB;
+			*val2 = 1000;
+			return IIO_VAL_FRACTIONAL;
+
+		case INA260_VOLTAGE:
+			*val = INA260_VOLTAGE_LSB;
+			*val2 = 1000;
+			return IIO_VAL_FRACTIONAL;
+
+		case INA260_POWER:
+			*val = INA260_POWER_LSB;
+			return IIO_VAL_INT;
+		}
+		return -EINVAL;
+
+	case IIO_CHAN_INFO_INT_TIME:
+		*val = 0;
+		if (chan->address == INA260_VOLTAGE)
+			*val2 = chip->config->volt_conv_time;
+		else
+			*val2 = chip->config->curr_conv_time;
+
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = DIV_ROUND_CLOSEST(1000000, SAMPLING_PERIOD(chip));
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		*val = chip->config->avgs;
+		return IIO_VAL_INT;
+	}
+
+	return -EINVAL;
+}
+
+static const int ina260_avg_tab[] = { 1, 4, 16, 64, 128, 256, 512, 1024 };
+
+/* Conversion times in uS */
+static const int ina260_conv_time_tab[] = { 140, 204, 332, 588, 1100, 2116, 4156, 8244 };
+
+static int ina260_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	struct ina260_chip *chip = iio_priv(indio_dev);
+	unsigned int config;
+	int ret, bits;
+
+	if (iio_buffer_enabled(indio_dev))
+		return -EBUSY;
+
+	mutex_lock(&chip->lock);
+
+	ret = regmap_read(chip->regmap, INA260_CONFIG, &config);
+	if (ret)
+		goto err;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_INT_TIME:
+		if (val2 > 8244 || val2 < 140) {
+			ret = -EINVAL;
+			goto err;
+		}
+
+		bits = find_closest(val2, ina260_conv_time_tab,
+				    ARRAY_SIZE(ina260_conv_time_tab));
+
+		if (chan->address == INA260_VOLTAGE) {
+			chip->config->volt_conv_time = ina260_conv_time_tab[bits];
+			config &= ~INA260_VOLT_MASK;
+			config |= INA260_SHIFT_VOLT(bits) & INA260_VOLT_MASK;
+		} else {
+			chip->config->curr_conv_time = ina260_conv_time_tab[bits];
+			config &= ~INA260_CURR_MASK;
+			config |= INA260_SHIFT_CURR(bits) & INA260_CURR_MASK;
+		}
+		break;
+
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		bits = find_closest(val, ina260_avg_tab, ARRAY_SIZE(ina260_avg_tab));
+		chip->config->avgs = ina260_avg_tab[bits];
+		config &= ~INA260_AVG_MASK;
+		config |= INA260_SHIFT_AVG(bits) & INA260_AVG_MASK;
+		break;
+
+	default:
+		ret = -EINVAL;
+	}
+	if (!ret)
+		ret = regmap_write(chip->regmap, INA260_CONFIG, config);
+err:
+	mutex_unlock(&chip->lock);
+
+	return ret;
+}
+
+static int ina260_debug_reg(struct iio_dev *indio_dev,
+			    unsigned int reg, unsigned int writeval, unsigned int *readval)
+{
+	struct ina260_chip *chip = iio_priv(indio_dev);
+
+	if (!readval)
+		return regmap_write(chip->regmap, reg, writeval);
+
+	return regmap_read(chip->regmap, reg, readval);
+}
+
+#define INA260_CHAN_VOLTAGE(_index, _address) { \
+	.type = IIO_VOLTAGE, \
+	.address = (_address), \
+	.indexed = 1, \
+	.channel = (_index), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+	BIT(IIO_CHAN_INFO_SCALE) | \
+	BIT(IIO_CHAN_INFO_INT_TIME), \
+	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+	BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+	.scan_index = (_index), \
+	.scan_type = { \
+		.sign = 'u', \
+		.realbits = 16, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	} \
+}
+
+#define INA260_CHAN_CURRENT(_index, _address) { \
+	.type = IIO_CURRENT, \
+	.address = (_address), \
+	.indexed = 1, \
+	.channel = (_index), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+	BIT(IIO_CHAN_INFO_SCALE) | \
+	BIT(IIO_CHAN_INFO_INT_TIME), \
+	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+	BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+	.scan_index = (_index), \
+	.scan_type = { \
+		.sign = 's', \
+		.realbits = 16, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	} \
+}
+
+#define INA260_CHAN_POWER(_index, _address) { \
+	.type = IIO_POWER, \
+	.address = (_address), \
+	.indexed = 1, \
+	.channel = (_index), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+	BIT(IIO_CHAN_INFO_SCALE), \
+	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+	BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+	.scan_index = (_index), \
+	.scan_type = { \
+		.sign = 'u', \
+		.realbits = 16, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	} \
+}
+
+static const struct iio_chan_spec ina260_channels[] = {
+	INA260_CHAN_CURRENT(0, INA260_CURRENT),
+	INA260_CHAN_VOLTAGE(1, INA260_VOLTAGE),
+	INA260_CHAN_POWER(2, INA260_POWER),
+	IIO_CHAN_SOFT_TIMESTAMP(3),
+};
+
+/* Possible integration times for current and voltage */
+static IIO_CONST_ATTR_NAMED(ina260_integration_time_available,
+			    integration_time_available,
+			    "0.000140 0.000204 0.000332 0.000588 0.001100 0.002116 0.004156 0.008244");
+
+static struct attribute *ina260_attributes[] = {
+	&iio_const_attr_ina260_integration_time_available.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group ina260_attribute_group = {
+	.attrs = ina260_attributes,
+};
+
+static const struct iio_info ina260_info = {
+	.attrs = &ina260_attribute_group,
+	.read_raw = ina260_read_raw,
+	.write_raw = ina260_write_raw,
+	.debugfs_reg_access = ina260_debug_reg,
+};
+
+static int ina260_conversion_ready(struct iio_dev *indio_dev)
+{
+	struct ina260_chip *chip = iio_priv(indio_dev);
+	unsigned int alert;
+	int ret;
+
+	ret = regmap_read(chip->regmap, INA260_MASK_ENABLE, &alert);
+	if (ret < 0)
+		return ret;
+
+	return (alert & INA260_CVRF);
+}
+
+static int ina260_work_buffer(struct iio_dev *indio_dev)
+{
+	/* data buffer needs space for channel data and timestap */
+	unsigned short data[3 + sizeof(s64) / sizeof(short)];
+	struct ina260_chip *chip = iio_priv(indio_dev);
+	int bit, ret, i = 0;
+	s64 time;
+
+	time = iio_get_time_ns(indio_dev);
+
+	/*
+	 * Read current, voltage and power from device
+	 */
+	for_each_set_bit(bit, indio_dev->active_scan_mask,
+			 indio_dev->masklength) {
+		unsigned int val;
+
+		ret = regmap_read(chip->regmap, INA260_CURRENT + bit, &val);
+		if (ret < 0)
+			return ret;
+
+		data[i++] = val;
+	}
+
+	iio_push_to_buffers_with_timestamp(indio_dev, data, time);
+
+	return 0;
+}
+
+static int ina260_capture_thread(void *data)
+{
+	struct iio_dev *indio_dev = data;
+	struct ina260_chip *chip = iio_priv(indio_dev);
+	int sampling_us = SAMPLING_PERIOD(chip);
+	struct timespec64 next, now, delta;
+	s64 delay_us;
+	int ret;
+
+	ktime_get_ts64(&next);
+
+	do {
+		while (1) {
+			/* Check if conversion is ready */
+			ret = ina260_conversion_ready(indio_dev);
+			if (ret < 0)
+				return ret;
+
+			/*
+			 * If the conversion was not yet finished,
+			 * reset the reference timestamp.
+			 */
+			if (ret == 0)
+				ktime_get_ts64(&next);
+			else
+				break;
+		}
+		/* Read the data from sensor and push it to buffers */
+		ret = ina260_work_buffer(indio_dev);
+		if (ret < 0)
+			return ret;
+
+		ktime_get_ts64(&now);
+		/*
+		 * Advance the timestamp for the next poll by one sampling
+		 * interval, and sleep for the remainder (next - now)
+		 * In case "next" has already passed, the interval is added
+		 * multiple times, i.e. samples are dropped.
+		 */
+		do {
+			timespec64_add_ns(&next, 1000 * sampling_us);
+			delta = timespec64_sub(next, now);
+			delay_us = div_s64(timespec64_to_ns(&delta), 1000);
+		} while (delay_us <= 0);
+
+		usleep_range(delay_us, (delay_us * 3) >> 1);
+
+	} while (!kthread_should_stop());
+
+	return 0;
+}
+
+static int ina260_buffer_enable(struct iio_dev *indio_dev)
+{
+	struct ina260_chip *chip = iio_priv(indio_dev);
+	unsigned int sampling_us = SAMPLING_PERIOD(chip);
+	struct task_struct *task;
+
+	task = kthread_create(ina260_capture_thread, (void *)indio_dev,
+			      "%s:%d-%uus", indio_dev->name, iio_device_id(indio_dev),
+			      sampling_us);
+
+	if (IS_ERR(task))
+		return PTR_ERR(task);
+
+	get_task_struct(task);
+	wake_up_process(task);
+	chip->task = task;
+
+	return 0;
+}
+
+static int ina260_buffer_disable(struct iio_dev *indio_dev)
+{
+	struct ina260_chip *chip = iio_priv(indio_dev);
+
+	if (chip->task) {
+		kthread_stop(chip->task);
+		put_task_struct(chip->task);
+		chip->task = NULL;
+	}
+
+	return 0;
+}
+
+static const struct iio_buffer_setup_ops ina260_setup_ops = {
+	.postenable = &ina260_buffer_enable,
+	.predisable = &ina260_buffer_disable,
+};
+
+static int ina260_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct iio_dev *indio_dev;
+	struct ina260_chip *chip;
+	enum ina260_ids type = 0;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	chip = iio_priv(indio_dev);
+	i2c_set_clientdata(client, indio_dev);
+
+	chip->regmap = devm_regmap_init_i2c(client, &ina260_regmap_config);
+	if (IS_ERR(chip->regmap)) {
+		dev_err(&client->dev, "failed to allocate register map\n");
+		return PTR_ERR(chip->regmap);
+	}
+
+	mutex_init(&chip->lock);
+
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->dev.parent = &client->dev;
+	indio_dev->dev.of_node = client->dev.of_node;
+
+	chip->config = &ina260_config[type];
+	ret = regmap_write(chip->regmap, INA260_CONFIG,
+			   chip->config->config_default);
+	if (ret) {
+		dev_err(&client->dev, "Error configuring the device\n");
+		return ret;
+	}
+	indio_dev->channels = ina260_channels;
+	indio_dev->num_channels = ARRAY_SIZE(ina260_channels);
+	indio_dev->info = &ina260_info;
+	indio_dev->name = id->name;
+
+	ret = devm_iio_kfifo_buffer_setup(&indio_dev->dev, indio_dev,
+					  INDIO_BUFFER_SOFTWARE,
+					  &ina260_setup_ops);
+	if (ret)
+		return ret;
+
+	return iio_device_register(indio_dev);
+}
+
+static int ina260_remove(struct i2c_client *client)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+	struct ina260_chip *chip = iio_priv(indio_dev);
+
+	iio_device_unregister(indio_dev);
+	/* Power down */
+	return regmap_update_bits(chip->regmap, INA260_CONFIG, INA260_MODE_MASK, 0);
+}
+
+static const struct i2c_device_id ina260_id[] = {
+	{"ina260", ina260},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ina260_id);
+
+static const struct of_device_id ina260_of_match[] = {
+	{
+		.compatible = "ti,ina260",
+		.data = (void *)ina260
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, ina260_of_match);
+
+static struct i2c_driver ina260_driver = {
+	.driver = {
+		.name = "ina260-adc",
+		.of_match_table = ina260_of_match,
+	},
+	.probe = ina260_probe,
+	.remove = ina260_remove,
+	.id_table = ina260_id,
+};
+module_i2c_driver(ina260_driver);
+
+MODULE_AUTHOR("Raviteja Narayanam <raviteja.narayanam@xilinx.com>");
+MODULE_DESCRIPTION("Texas Instruments INA 260 ADC driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ina2xx-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ina2xx-adc.c
@@ -124,6 +124,7 @@
 enum ina2xx_ids { ina219, ina226 };
 
 struct ina2xx_config {
+	const char *name;
 	u16 config_default;
 	int calibration_value;
 	int shunt_voltage_lsb;	/* nV */
@@ -155,6 +156,7 @@
 
 static const struct ina2xx_config ina2xx_config[] = {
 	[ina219] = {
+		.name = "ina219",
 		.config_default = INA219_CONFIG_DEFAULT,
 		.calibration_value = 4096,
 		.shunt_voltage_lsb = 10000,
@@ -164,6 +166,7 @@
 		.chip_id = ina219,
 	},
 	[ina226] = {
+		.name = "ina226",
 		.config_default = INA226_CONFIG_DEFAULT,
 		.calibration_value = 2048,
 		.shunt_voltage_lsb = 2500,
@@ -999,7 +1002,7 @@
 	/* Patch the current config register with default. */
 	val = chip->config->config_default;
 
-	if (id->driver_data == ina226) {
+	if (type == ina226) {
 		ina226_set_average(chip, INA226_DEFAULT_AVG, &val);
 		ina226_set_int_time_vbus(chip, INA226_DEFAULT_IT, &val);
 		ina226_set_int_time_vshunt(chip, INA226_DEFAULT_IT, &val);
@@ -1018,7 +1021,7 @@
 	}
 
 	indio_dev->modes = INDIO_DIRECT_MODE;
-	if (id->driver_data == ina226) {
+	if (type == ina226) {
 		indio_dev->channels = ina226_channels;
 		indio_dev->num_channels = ARRAY_SIZE(ina226_channels);
 		indio_dev->info = &ina226_info;
@@ -1027,7 +1030,7 @@
 		indio_dev->num_channels = ARRAY_SIZE(ina219_channels);
 		indio_dev->info = &ina219_info;
 	}
-	indio_dev->name = id->name;
+	indio_dev->name = id ? id->name : chip->config->name;
 
 	ret = devm_iio_kfifo_buffer_setup(&client->dev, indio_dev,
 					  INDIO_BUFFER_SOFTWARE,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ltc2497.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ltc2497.c
@@ -41,6 +41,19 @@
 		}
 
 		*val = (be32_to_cpu(st->buf) >> 14) - (1 << 17);
+
+		/*
+		 * The part started a new conversion at the end of the above i2c
+		 * transfer, so if the address didn't change since the last call
+		 * everything is fine and we can return early.
+		 * If not (which should only happen when some sort of bulk
+		 * conversion is implemented) we have to program the new
+		 * address. Note that this probably fails as the conversion that
+		 * was triggered above is like not complete yet and the two
+		 * operations have to be done in a single transfer.
+		 */
+		if (ddata->addr_prev == address)
+			return 0;
 	}
 
 	ret = i2c_smbus_write_byte(st->client,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/mcp3911.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/mcp3911.c
@@ -38,8 +38,8 @@
 #define MCP3911_CHANNEL(x)		(MCP3911_REG_CHANNEL0 + x * 3)
 #define MCP3911_OFFCAL(x)		(MCP3911_REG_OFFCAL_CH0 + x * 6)
 
-/* Internal voltage reference in uV */
-#define MCP3911_INT_VREF_UV		1200000
+/* Internal voltage reference in mV */
+#define MCP3911_INT_VREF_MV		1200
 
 #define MCP3911_REG_READ(reg, id)	((((reg) << 1) | ((id) << 5) | (1 << 0)) & 0xff)
 #define MCP3911_REG_WRITE(reg, id)	((((reg) << 1) | ((id) << 5) | (0 << 0)) & 0xff)
@@ -111,6 +111,8 @@
 		if (ret)
 			goto out;
 
+		*val = sign_extend32(*val, 23);
+
 		ret = IIO_VAL_INT;
 		break;
 
@@ -135,11 +137,18 @@
 
 			*val = ret / 1000;
 		} else {
-			*val = MCP3911_INT_VREF_UV;
+			*val = MCP3911_INT_VREF_MV;
 		}
 
-		*val2 = 24;
-		ret = IIO_VAL_FRACTIONAL_LOG2;
+		/*
+		 * For 24bit Conversion
+		 * Raw = ((Voltage)/(Vref) * 2^23 * Gain * 1.5
+		 * Voltage = Raw * (Vref)/(2^23 * Gain * 1.5)
+		 */
+
+		/* val2 = (2^23 * 1.5) */
+		*val2 = 12582912;
+		ret = IIO_VAL_FRACTIONAL;
 		break;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/men_z188_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/men_z188_adc.c
@@ -103,6 +103,7 @@
 	struct z188_adc *adc;
 	struct iio_dev *indio_dev;
 	struct resource *mem;
+	int ret;
 
 	indio_dev = devm_iio_device_alloc(&dev->dev, sizeof(struct z188_adc));
 	if (!indio_dev)
@@ -128,8 +129,14 @@
 	adc->mem = mem;
 	mcb_set_drvdata(dev, indio_dev);
 
-	return iio_device_register(indio_dev);
+	ret = iio_device_register(indio_dev);
+	if (ret)
+		goto err_unmap;
 
+	return 0;
+
+err_unmap:
+	iounmap(adc->base);
 err:
 	mcb_release_mem(mem);
 	return -ENXIO;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/meson_saradc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/meson_saradc.c
@@ -71,7 +71,7 @@
 	#define MESON_SAR_ADC_REG3_PANEL_DETECT_COUNT_MASK	GENMASK(20, 18)
 	#define MESON_SAR_ADC_REG3_PANEL_DETECT_FILTER_TB_MASK	GENMASK(17, 16)
 	#define MESON_SAR_ADC_REG3_ADC_CLK_DIV_SHIFT		10
-	#define MESON_SAR_ADC_REG3_ADC_CLK_DIV_WIDTH		5
+	#define MESON_SAR_ADC_REG3_ADC_CLK_DIV_WIDTH		6
 	#define MESON_SAR_ADC_REG3_BLOCK_DLY_SEL_MASK		GENMASK(9, 8)
 	#define MESON_SAR_ADC_REG3_BLOCK_DLY_MASK		GENMASK(7, 0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/mp2629_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/mp2629_adc.c
@@ -56,7 +56,8 @@
 	MP2629_MAP(SYSTEM_VOLT, "system-volt"),
 	MP2629_MAP(INPUT_VOLT, "input-volt"),
 	MP2629_MAP(BATT_CURRENT, "batt-current"),
-	MP2629_MAP(INPUT_CURRENT, "input-current")
+	MP2629_MAP(INPUT_CURRENT, "input-current"),
+	{ }
 };
 
 static int mp2629_read_raw(struct iio_dev *indio_dev,
@@ -73,7 +74,7 @@
 		if (ret)
 			return ret;
 
-		if (chan->address == MP2629_INPUT_VOLT)
+		if (chan->channel == MP2629_INPUT_VOLT)
 			rval &= GENMASK(6, 0);
 		*val = rval;
 		return IIO_VAL_INT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/mxs-lradc-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/mxs-lradc-adc.c
@@ -757,13 +757,13 @@
 
 	ret = mxs_lradc_adc_trigger_init(iio);
 	if (ret)
-		goto err_trig;
+		return ret;
 
 	ret = iio_triggered_buffer_setup(iio, &iio_pollfunc_store_time,
 					 &mxs_lradc_adc_trigger_handler,
 					 &mxs_lradc_adc_buffer_ops);
 	if (ret)
-		return ret;
+		goto err_trig;
 
 	adc->vref_mv = mxs_lradc_adc_vref_mv[lradc->soc];
 
@@ -801,9 +801,9 @@
 
 err_dev:
 	mxs_lradc_adc_hw_stop(adc);
-	mxs_lradc_adc_trigger_remove(iio);
-err_trig:
 	iio_triggered_buffer_cleanup(iio);
+err_trig:
+	mxs_lradc_adc_trigger_remove(iio);
 	return ret;
 }
 
@@ -814,8 +814,8 @@
 
 	iio_device_unregister(iio);
 	mxs_lradc_adc_hw_stop(adc);
-	mxs_lradc_adc_trigger_remove(iio);
 	iio_triggered_buffer_cleanup(iio);
+	mxs_lradc_adc_trigger_remove(iio);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/palmas_gpadc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/palmas_gpadc.c
@@ -638,7 +638,7 @@
 
 static int palmas_gpadc_remove(struct platform_device *pdev)
 {
-	struct iio_dev *indio_dev = dev_to_iio_dev(&pdev->dev);
+	struct iio_dev *indio_dev = dev_get_drvdata(&pdev->dev);
 	struct palmas_gpadc *adc = iio_priv(indio_dev);
 
 	if (adc->wakeup1_enable || adc->wakeup2_enable)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/rockchip_saradc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/rockchip_saradc.c
@@ -270,6 +270,8 @@
 	int ret;
 	int i, j = 0;
 
+	memset(&data, 0, sizeof(data));
+
 	mutex_lock(&i_dev->mlock);
 
 	for_each_set_bit(i, i_dev->active_scan_mask, i_dev->masklength) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/rzg2l_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/rzg2l_adc.c
@@ -334,11 +334,15 @@
 	i = 0;
 	device_for_each_child_node(&pdev->dev, fwnode) {
 		ret = fwnode_property_read_u32(fwnode, "reg", &channel);
-		if (ret)
+		if (ret) {
+			fwnode_handle_put(fwnode);
 			return ret;
+		}
 
-		if (channel >= RZG2L_ADC_MAX_CHANNELS)
+		if (channel >= RZG2L_ADC_MAX_CHANNELS) {
+			fwnode_handle_put(fwnode);
 			return -EINVAL;
+		}
 
 		chan_array[i].type = IIO_VOLTAGE;
 		chan_array[i].indexed = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/sc27xx_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/sc27xx_adc.c
@@ -36,8 +36,8 @@
 
 /* Bits and mask definition for SC27XX_ADC_CH_CFG register */
 #define SC27XX_ADC_CHN_ID_MASK		GENMASK(4, 0)
-#define SC27XX_ADC_SCALE_MASK		GENMASK(10, 8)
-#define SC27XX_ADC_SCALE_SHIFT		8
+#define SC27XX_ADC_SCALE_MASK		GENMASK(10, 9)
+#define SC27XX_ADC_SCALE_SHIFT		9
 
 /* Bits definitions for SC27XX_ADC_INT_EN registers */
 #define SC27XX_ADC_IRQ_EN		BIT(0)
@@ -103,14 +103,14 @@
 	100, 341,
 };
 
-static const struct sc27xx_adc_linear_graph big_scale_graph_calib = {
-	4200, 856,
-	3600, 733,
+static const struct sc27xx_adc_linear_graph sc2731_big_scale_graph_calib = {
+	4200, 850,
+	3600, 728,
 };
 
-static const struct sc27xx_adc_linear_graph small_scale_graph_calib = {
-	1000, 833,
-	100, 80,
+static const struct sc27xx_adc_linear_graph sc2731_small_scale_graph_calib = {
+	1000, 838,
+	100, 84,
 };
 
 static int sc27xx_adc_get_calib_data(u32 calib_data, int calib_adc)
@@ -130,11 +130,11 @@
 	size_t len;
 
 	if (big_scale) {
-		calib_graph = &big_scale_graph_calib;
+		calib_graph = &sc2731_big_scale_graph_calib;
 		graph = &big_scale_graph;
 		cell_name = "big_scale_calib";
 	} else {
-		calib_graph = &small_scale_graph_calib;
+		calib_graph = &sc2731_small_scale_graph_calib;
 		graph = &small_scale_graph;
 		cell_name = "small_scale_calib";
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/stm32-adc-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/stm32-adc-core.c
@@ -64,6 +64,7 @@
  * @max_clk_rate_hz: maximum analog clock rate (Hz, from datasheet)
  * @has_syscfg: SYSCFG capability flags
  * @num_irqs:	number of interrupt lines
+ * @num_adcs:   maximum number of ADC instances in the common registers
  */
 struct stm32_adc_priv_cfg {
 	const struct stm32_adc_common_regs *regs;
@@ -71,6 +72,7 @@
 	u32 max_clk_rate_hz;
 	unsigned int has_syscfg;
 	unsigned int num_irqs;
+	unsigned int num_adcs;
 };
 
 /**
@@ -352,7 +354,7 @@
 	 * before invoking the interrupt handler (e.g. call ISR only for
 	 * IRQ-enabled ADCs).
 	 */
-	for (i = 0; i < priv->cfg->num_irqs; i++) {
+	for (i = 0; i < priv->cfg->num_adcs; i++) {
 		if ((status & priv->cfg->regs->eoc_msk[i] &&
 		     stm32_adc_eoc_enabled(priv, i)) ||
 		     (status & priv->cfg->regs->ovr_msk[i]))
@@ -796,6 +798,7 @@
 	.clk_sel = stm32f4_adc_clk_sel,
 	.max_clk_rate_hz = 36000000,
 	.num_irqs = 1,
+	.num_adcs = 3,
 };
 
 static const struct stm32_adc_priv_cfg stm32h7_adc_priv_cfg = {
@@ -804,14 +807,16 @@
 	.max_clk_rate_hz = 36000000,
 	.has_syscfg = HAS_VBOOSTER,
 	.num_irqs = 1,
+	.num_adcs = 2,
 };
 
 static const struct stm32_adc_priv_cfg stm32mp1_adc_priv_cfg = {
 	.regs = &stm32h7_adc_common_regs,
 	.clk_sel = stm32h7_adc_clk_sel,
-	.max_clk_rate_hz = 40000000,
+	.max_clk_rate_hz = 36000000,
 	.has_syscfg = HAS_VBOOSTER | HAS_ANASWVDD,
 	.num_irqs = 2,
+	.num_adcs = 2,
 };
 
 static const struct of_device_id stm32_adc_of_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/stm32-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/stm32-adc.c
@@ -975,6 +975,7 @@
 {
 	struct stm32_adc *adc = iio_priv(indio_dev);
 
+	stm32_adc_writel(adc, STM32H7_ADC_PCSEL, 0);
 	stm32h7_adc_disable(indio_dev);
 	stm32h7_adc_enter_pwr_down(adc);
 }
@@ -1258,7 +1259,6 @@
 	struct stm32_adc *adc = iio_priv(indio_dev);
 	const struct stm32_adc_regspec *regs = adc->cfg->regs;
 	u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg);
-	u32 mask = stm32_adc_readl(adc, regs->ier_eoc.reg);
 
 	/* Check ovr status right now, as ovr mask should be already disabled */
 	if (status & regs->isr_ovr.mask) {
@@ -1273,11 +1273,6 @@
 		return IRQ_HANDLED;
 	}
 
-	if (!(status & mask))
-		dev_err_ratelimited(&indio_dev->dev,
-				    "Unexpected IRQ: IER=0x%08x, ISR=0x%08x\n",
-				    mask, status);
-
 	return IRQ_NONE;
 }
 
@@ -1287,10 +1282,6 @@
 	struct stm32_adc *adc = iio_priv(indio_dev);
 	const struct stm32_adc_regspec *regs = adc->cfg->regs;
 	u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg);
-	u32 mask = stm32_adc_readl(adc, regs->ier_eoc.reg);
-
-	if (!(status & mask))
-		return IRQ_WAKE_THREAD;
 
 	if (status & regs->isr_ovr.mask) {
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/stm32-dfsdm-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/stm32-dfsdm-adc.c
@@ -1521,6 +1521,7 @@
 	},
 	{}
 };
+MODULE_DEVICE_TABLE(of, stm32_dfsdm_adc_match);
 
 static int stm32_dfsdm_adc_probe(struct platform_device *pdev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/stmpe-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/stmpe-adc.c
@@ -61,7 +61,7 @@
 static int stmpe_read_voltage(struct stmpe_adc *info,
 		struct iio_chan_spec const *chan, int *val)
 {
-	long ret;
+	unsigned long ret;
 
 	mutex_lock(&info->lock);
 
@@ -79,7 +79,7 @@
 
 	ret = wait_for_completion_timeout(&info->completion, STMPE_ADC_TIMEOUT);
 
-	if (ret <= 0) {
+	if (ret == 0) {
 		stmpe_reg_write(info->stmpe, STMPE_REG_ADC_INT_STA,
 				STMPE_ADC_CH(info->channel));
 		mutex_unlock(&info->lock);
@@ -96,7 +96,7 @@
 static int stmpe_read_temp(struct stmpe_adc *info,
 		struct iio_chan_spec const *chan, int *val)
 {
-	long ret;
+	unsigned long ret;
 
 	mutex_lock(&info->lock);
 
@@ -114,7 +114,7 @@
 
 	ret = wait_for_completion_timeout(&info->completion, STMPE_ADC_TIMEOUT);
 
-	if (ret <= 0) {
+	if (ret == 0) {
 		mutex_unlock(&info->lock);
 		return -ETIMEDOUT;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-adc081c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-adc081c.c
@@ -19,6 +19,7 @@
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
+#include <linux/property.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
@@ -156,13 +157,16 @@
 {
 	struct iio_dev *iio;
 	struct adc081c *adc;
-	struct adcxx1c_model *model;
+	const struct adcxx1c_model *model;
 	int err;
 
 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA))
 		return -EOPNOTSUPP;
 
-	model = &adcxx1c_models[id->driver_data];
+	if (dev_fwnode(&client->dev))
+		model = device_get_match_data(&client->dev);
+	else
+		model = &adcxx1c_models[id->driver_data];
 
 	iio = devm_iio_device_alloc(&client->dev, sizeof(*adc));
 	if (!iio)
@@ -210,10 +214,17 @@
 };
 MODULE_DEVICE_TABLE(i2c, adc081c_id);
 
+static const struct acpi_device_id adc081c_acpi_match[] = {
+	/* Used on some AAEON boards */
+	{ "ADC081C", (kernel_ulong_t)&adcxx1c_models[ADC081C] },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, adc081c_acpi_match);
+
 static const struct of_device_id adc081c_of_match[] = {
-	{ .compatible = "ti,adc081c" },
-	{ .compatible = "ti,adc101c" },
-	{ .compatible = "ti,adc121c" },
+	{ .compatible = "ti,adc081c", .data = &adcxx1c_models[ADC081C] },
+	{ .compatible = "ti,adc101c", .data = &adcxx1c_models[ADC101C] },
+	{ .compatible = "ti,adc121c", .data = &adcxx1c_models[ADC121C] },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, adc081c_of_match);
@@ -222,6 +233,7 @@
 	.driver = {
 		.name = "adc081c",
 		.of_match_table = adc081c_of_match,
+		.acpi_match_table = adc081c_acpi_match,
 	},
 	.probe = adc081c_probe,
 	.id_table = adc081c_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-adc128s052.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-adc128s052.c
@@ -193,13 +193,13 @@
 }
 
 static const struct of_device_id adc128_of_match[] = {
-	{ .compatible = "ti,adc128s052", },
-	{ .compatible = "ti,adc122s021", },
-	{ .compatible = "ti,adc122s051", },
-	{ .compatible = "ti,adc122s101", },
-	{ .compatible = "ti,adc124s021", },
-	{ .compatible = "ti,adc124s051", },
-	{ .compatible = "ti,adc124s101", },
+	{ .compatible = "ti,adc128s052", .data = (void*)0L, },
+	{ .compatible = "ti,adc122s021", .data = (void*)1L, },
+	{ .compatible = "ti,adc122s051", .data = (void*)1L, },
+	{ .compatible = "ti,adc122s101", .data = (void*)1L, },
+	{ .compatible = "ti,adc124s021", .data = (void*)2L, },
+	{ .compatible = "ti,adc124s051", .data = (void*)2L, },
+	{ .compatible = "ti,adc124s101", .data = (void*)2L, },
 	{ /* sentinel */ },
 };
 MODULE_DEVICE_TABLE(of, adc128_of_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-ads124s08.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-ads124s08.c
@@ -184,9 +184,9 @@
 	struct ads124s_private *priv = iio_priv(indio_dev);
 
 	if (priv->reset_gpio) {
-		gpiod_set_value(priv->reset_gpio, 0);
+		gpiod_set_value_cansleep(priv->reset_gpio, 0);
 		udelay(200);
-		gpiod_set_value(priv->reset_gpio, 1);
+		gpiod_set_value_cansleep(priv->reset_gpio, 1);
 	} else {
 		return ads124s_write_cmd(indio_dev, ADS124S08_CMD_RESET);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-ads131e08.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-ads131e08.c
@@ -739,7 +739,7 @@
 	device_for_each_child_node(dev, node) {
 		ret = fwnode_property_read_u32(node, "reg", &channel);
 		if (ret)
-			return ret;
+			goto err_child_out;
 
 		ret = fwnode_property_read_u32(node, "ti,gain", &tmp);
 		if (ret) {
@@ -747,7 +747,7 @@
 		} else {
 			ret = ads131e08_pga_gain_to_field_value(st, tmp);
 			if (ret < 0)
-				return ret;
+				goto err_child_out;
 
 			channel_config[i].pga_gain = tmp;
 		}
@@ -758,7 +758,7 @@
 		} else {
 			ret = ads131e08_validate_channel_mux(st, tmp);
 			if (ret)
-				return ret;
+				goto err_child_out;
 
 			channel_config[i].mux = tmp;
 		}
@@ -784,6 +784,10 @@
 	st->channel_config = channel_config;
 
 	return 0;
+
+err_child_out:
+	fwnode_handle_put(node);
+	return ret;
 }
 
 static void ads131e08_regulator_disable(void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-ads7950.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-ads7950.c
@@ -634,6 +634,7 @@
 	st->chip.label = dev_name(&st->spi->dev);
 	st->chip.parent = &st->spi->dev;
 	st->chip.owner = THIS_MODULE;
+	st->chip.can_sleep = true;
 	st->chip.base = -1;
 	st->chip.ngpio = TI_ADS7950_NUM_GPIOS;
 	st->chip.get_direction = ti_ads7950_get_direction;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-ads8688.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-ads8688.c
@@ -384,7 +384,7 @@
 	struct iio_poll_func *pf = p;
 	struct iio_dev *indio_dev = pf->indio_dev;
 	/* Ensure naturally aligned timestamp */
-	u16 buffer[ADS8688_MAX_CHANNELS + sizeof(s64)/sizeof(u16)] __aligned(8);
+	u16 buffer[ADS8688_MAX_CHANNELS + sizeof(s64)/sizeof(u16)] __aligned(8) = { };
 	int i, j = 0;
 
 	for (i = 0; i < indio_dev->masklength; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti-tsc2046.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti-tsc2046.c
@@ -388,7 +388,7 @@
 	mutex_lock(&priv->slock);
 
 	size = 0;
-	for_each_set_bit(ch_idx, active_scan_mask, indio_dev->num_channels) {
+	for_each_set_bit(ch_idx, active_scan_mask, ARRAY_SIZE(priv->l)) {
 		size += tsc2046_adc_group_set_layout(priv, group, ch_idx);
 		tsc2046_adc_group_set_cmd(priv, group, ch_idx);
 		group++;
@@ -398,7 +398,7 @@
 	priv->xfer.len = size;
 	priv->time_per_scan_us = size * 8 * priv->time_per_bit_ns / NSEC_PER_USEC;
 
-	if (priv->scan_interval_us > priv->time_per_scan_us)
+	if (priv->scan_interval_us < priv->time_per_scan_us)
 		dev_warn(&priv->spi->dev, "The scan interval (%d) is less then calculated scan time (%d)\n",
 			 priv->scan_interval_us, priv->time_per_scan_us);
 
@@ -548,7 +548,7 @@
 	 * enabled.
 	 */
 	size = 0;
-	for (ch_idx = 0; ch_idx < priv->dcfg->num_channels; ch_idx++)
+	for (ch_idx = 0; ch_idx < ARRAY_SIZE(priv->l); ch_idx++)
 		size += tsc2046_adc_group_set_layout(priv, ch_idx, ch_idx);
 
 	priv->tx = devm_kzalloc(&priv->spi->dev, size, GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/ti_am335x_adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/ti_am335x_adc.c
@@ -632,8 +632,10 @@
 	platform_set_drvdata(pdev, indio_dev);
 
 	err = tiadc_request_dma(pdev, adc_dev);
-	if (err && err == -EPROBE_DEFER)
+	if (err && err != -ENODEV) {
+		dev_err_probe(&pdev->dev, err, "DMA request failed\n");
 		goto err_dma;
+	}
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/twl6030-gpadc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/twl6030-gpadc.c
@@ -57,6 +57,18 @@
 #define TWL6030_GPADCS				BIT(1)
 #define TWL6030_GPADCR				BIT(0)
 
+#define USB_VBUS_CTRL_SET			0x04
+#define USB_ID_CTRL_SET				0x06
+
+#define TWL6030_MISC1				0xE4
+#define VBUS_MEAS				0x01
+#define ID_MEAS					0x01
+
+#define VAC_MEAS                0x04
+#define VBAT_MEAS               0x02
+#define BB_MEAS                 0x01
+
+
 /**
  * struct twl6030_chnl_calib - channel calibration
  * @gain:		slope coefficient for ideal curve
@@ -911,6 +923,8 @@
 	ret = devm_request_threaded_irq(dev, irq, NULL,
 				twl6030_gpadc_irq_handler,
 				IRQF_ONESHOT, "twl6030_gpadc", indio_dev);
+	if (ret)
+		return ret;
 
 	ret = twl6030_gpadc_enable_irq(TWL6030_GPADC_RT_SW1_EOC_MASK);
 	if (ret < 0) {
@@ -925,6 +939,26 @@
 		return ret;
 	}
 
+	ret = twl_i2c_write_u8(TWL_MODULE_USB, VBUS_MEAS, USB_VBUS_CTRL_SET);
+	if (ret < 0) {
+		dev_err(dev, "failed to wire up inputs\n");
+		return ret;
+	}
+
+	ret = twl_i2c_write_u8(TWL_MODULE_USB, ID_MEAS, USB_ID_CTRL_SET);
+	if (ret < 0) {
+		dev_err(dev, "failed to wire up inputs\n");
+		return ret;
+	}
+
+	ret = twl_i2c_write_u8(TWL6030_MODULE_ID0,
+				VBAT_MEAS | BB_MEAS | VAC_MEAS,
+				TWL6030_MISC1);
+	if (ret < 0) {
+		dev_err(dev, "failed to wire up inputs\n");
+		return ret;
+	}
+
 	indio_dev->name = DRIVER_NAME;
 	indio_dev->info = &twl6030_gpadc_iio_info;
 	indio_dev->modes = INDIO_DIRECT_MODE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/versal-sysmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/versal-sysmon.c
@@ -0,0 +1,1141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx SYSMON for Versal
+ *
+ * Copyright (C) 2019 - 2021 Xilinx, Inc.
+ *
+ * Description:
+ * This driver is developed for SYSMON on Versal. The driver supports INDIO Mode
+ * and supports voltage and temperature monitoring via IIO sysfs interface and
+ * in kernel event monitoring for some modules.
+ */
+
+#include <dt-bindings/power/xlnx-versal-power.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/moduleparam.h>
+#include "versal-sysmon.h"
+
+#define SYSMON_EVENT_WORK_DELAY_MS	1000
+#define SYSMON_UNMASK_WORK_DELAY_MS	500
+
+static bool secure_mode;
+module_param(secure_mode, bool, 0444);
+MODULE_PARM_DESC(secure_mode,
+		 "Allow sysmon to access register space using EEMI, when direct register access is restricted (default: Direct Access mode)");
+
+/* This structure describes temperature events */
+static const struct iio_event_spec sysmon_temp_events[] = {
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_RISING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE),
+	},
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_FALLING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE),
+	},
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_EITHER,
+		.mask_separate =
+			BIT(IIO_EV_INFO_ENABLE) | BIT(IIO_EV_INFO_HYSTERESIS),
+	},
+};
+
+/* This structure describes voltage events */
+static const struct iio_event_spec sysmon_supply_events[] = {
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_RISING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE),
+	},
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_FALLING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE),
+	},
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_EITHER,
+		.mask_separate = BIT(IIO_EV_INFO_ENABLE),
+	},
+};
+
+/* Temperature channel attributes */
+static const struct iio_chan_spec temp_channels[] = {
+	SYSMON_CHAN_TEMP(TEMP_MAX, "temp"),
+	SYSMON_CHAN_TEMP(TEMP_MIN, "min"),
+	SYSMON_CHAN_TEMP(TEMP_MAX_MAX, "max_max"),
+	SYSMON_CHAN_TEMP(TEMP_MIN_MIN, "min_min"),
+};
+
+/* Temperature event attributes */
+static const struct iio_chan_spec temp_events[] = {
+	SYSMON_CHAN_TEMP_EVENT(TEMP_EVENT, "temp", sysmon_temp_events),
+	SYSMON_CHAN_TEMP_EVENT(OT_EVENT, "ot", sysmon_temp_events),
+};
+
+static inline void sysmon_direct_read_reg(struct sysmon *sysmon, u32 offset, u32 *data)
+{
+	*data = readl(sysmon->base + offset);
+}
+
+static inline void sysmon_direct_write_reg(struct sysmon *sysmon, u32 offset, u32 data)
+{
+	writel(data, sysmon->base + offset);
+}
+
+static inline void sysmon_direct_update_reg(struct sysmon *sysmon, u32 offset,
+					    u32 mask, u32 data)
+{
+	u32 val;
+
+	sysmon_direct_read_reg(sysmon, offset, &val);
+	sysmon_direct_write_reg(sysmon, offset, (val & ~mask) | (mask & data));
+}
+
+static struct sysmon_ops direct_access = {
+	.read_reg = sysmon_direct_read_reg,
+	.write_reg = sysmon_direct_write_reg,
+	.update_reg = sysmon_direct_update_reg,
+};
+
+static inline void sysmon_secure_read_reg(struct sysmon *sysmon, u32 offset, u32 *data)
+{
+	zynqmp_pm_sec_read_reg(PM_DEV_AMS_ROOT, offset, data);
+}
+
+static inline void sysmon_secure_write_reg(struct sysmon *sysmon, u32 offset, u32 data)
+{
+	zynqmp_pm_sec_mask_write_reg(PM_DEV_AMS_ROOT, offset, GENMASK(31, 0), data);
+}
+
+static inline void sysmon_secure_update_reg(struct sysmon *sysmon, u32 offset,
+					    u32 mask, u32 data)
+{
+	zynqmp_pm_sec_mask_write_reg(PM_DEV_AMS_ROOT, offset, offset, data);
+}
+
+static struct sysmon_ops secure_access = {
+	.read_reg = sysmon_secure_read_reg,
+	.write_reg = sysmon_secure_write_reg,
+	.update_reg = sysmon_secure_update_reg,
+};
+
+static void sysmon_read_reg(struct sysmon *sysmon, u32 offset, u32 *data)
+{
+	sysmon->ops->read_reg(sysmon, offset, data);
+}
+
+static void sysmon_write_reg(struct sysmon *sysmon, u32 offset, u32 data)
+{
+	sysmon->ops->write_reg(sysmon, offset, data);
+}
+
+static void sysmon_update_reg(struct sysmon *sysmon, u32 offset, u32 mask, u32 data)
+{
+	sysmon->ops->update_reg(sysmon, offset, mask, data);
+}
+
+static u32 sysmon_temp_offset(int address)
+{
+	switch (address) {
+	case TEMP_MAX:
+		return SYSMON_TEMP_MAX;
+	case TEMP_MIN:
+		return SYSMON_TEMP_MIN;
+	case TEMP_MAX_MAX:
+		return SYSMON_TEMP_MAX_MAX;
+	case TEMP_MIN_MIN:
+		return SYSMON_TEMP_MIN_MIN;
+	default:
+		return -EINVAL;
+	}
+	return -EINVAL;
+}
+
+static u32 sysmon_temp_thresh_offset(int address, enum iio_event_direction dir)
+{
+	switch (address) {
+	case TEMP_EVENT:
+		return (dir == IIO_EV_DIR_RISING) ? SYSMON_TEMP_TH_UP :
+						    SYSMON_TEMP_TH_LOW;
+	case OT_EVENT:
+		return (dir == IIO_EV_DIR_RISING) ? SYSMON_OT_TH_UP :
+						    SYSMON_OT_TH_LOW;
+	default:
+		return -EINVAL;
+	}
+	return -EINVAL;
+}
+
+static u32 sysmon_supply_offset(int address)
+{
+	return (address * 4) + SYSMON_SUPPLY_BASE;
+}
+
+static u32 sysmon_supply_thresh_offset(int address,
+				       enum iio_event_direction dir)
+{
+	if (dir == IIO_EV_DIR_RISING)
+		return (address * 4) + SYSMON_SUPPLY_TH_UP;
+	else if (dir == IIO_EV_DIR_FALLING)
+		return (address * 4) + SYSMON_SUPPLY_TH_LOW;
+
+	return -EINVAL;
+}
+
+/**
+ * sysmon_q8p7_to_celsius() - converts fixed point Q8.7 format to a fraction.
+ * @raw_data: Raw ADC value
+ * @val: The numerator of the fraction needed by IIO_VAL_PROCESSED
+ * @val2: Denominator of the fraction needed by IIO_VAL_PROCESSED
+ *
+ * The function returns a fraction which returns celsius
+ */
+static void sysmon_q8p7_to_celsius(int raw_data, int *val, int *val2)
+{
+	*val = (raw_data & 0x8000) ? -(twoscomp(raw_data)) : raw_data;
+	*val2 = 128;
+}
+
+/**
+ * sysmon_celsius_to_q8p7() - converts value from IIO Framework to ADC Raw data
+ * @raw_data: Raw ADC value
+ * @val: The numerator of the fraction provided by the IIO Framework
+ * @val2: Denominator of the fraction provided by the IIO Framework
+ *
+ * The function takes in exponent and mantissa as val and val2 respectively
+ * of temperature value in Deg Celsius and returns raw adc value for the
+ * given temperature.
+ */
+static void sysmon_celsius_to_q8p7(u32 *raw_data, int val, int val2)
+{
+	int scale = 1 << 7;
+
+	/* The value is scaled by 10^6 in the IIO framework
+	 * dividing by 1000 twice to avoid overflow
+	 */
+	val2 = val2 / 1000;
+	*raw_data = (val * scale) + ((val2 * scale) / 1000);
+}
+
+static void sysmon_supply_rawtoprocessed(int raw_data, int *val, int *val2)
+{
+	int mantissa, format, exponent;
+
+	mantissa = raw_data & SYSMON_MANTISSA_MASK;
+	exponent = (raw_data & SYSMON_MODE_MASK) >> SYSMON_MODE_SHIFT;
+	format = (raw_data & SYSMON_FMT_MASK) >> SYSMON_FMT_SHIFT;
+
+	*val2 = 1 << (16 - exponent);
+	*val = mantissa;
+	if (format && (mantissa >> SYSMON_MANTISSA_SIGN_SHIFT))
+		*val = (~(mantissa) & SYSMON_MANTISSA_MASK) * -1;
+}
+
+static void sysmon_supply_processedtoraw(int val, int val2, u32 reg_val,
+					 u32 *raw_data)
+{
+	int exponent = (reg_val & SYSMON_MODE_MASK) >> SYSMON_MODE_SHIFT;
+	int format = (reg_val & SYSMON_FMT_MASK) >> SYSMON_FMT_SHIFT;
+	int scale = 1 << (16 - exponent);
+	int tmp;
+
+	/**
+	 * The value is scaled by 10^6 in the IIO framework
+	 * dividing by 1000 twice to avoid overflow
+	 */
+	val2 = val2 / 1000;
+	tmp = (val * scale) + ((val2 * scale) / 1000);
+
+	/* Set out of bound values to saturation levels */
+	if (format) {
+		if (tmp > SYSMON_UPPER_SATURATION_SIGNED)
+			tmp = 0x7fff;
+		else if (tmp < SYSMON_LOWER_SATURATION_SIGNED)
+			tmp = 0x8000;
+
+	} else {
+		if (tmp > SYSMON_UPPER_SATURATION)
+			tmp = 0xffff;
+		else if (tmp < SYSMON_LOWER_SATURATION)
+			tmp = 0x0000;
+	}
+
+	*raw_data = tmp & 0xffff;
+}
+
+static int sysmon_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan, int *val,
+			   int *val2, long mask)
+{
+	struct sysmon *sysmon = iio_priv(indio_dev);
+	u32 offset, regval;
+	u32 ret = -EINVAL;
+
+	mutex_lock(&sysmon->mutex);
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		switch (chan->type) {
+		case IIO_TEMP:
+			offset = sysmon_temp_offset(chan->address);
+			sysmon_read_reg(sysmon, offset, val);
+			*val2 = 0;
+			ret = IIO_VAL_INT;
+			break;
+
+		case IIO_VOLTAGE:
+			offset = sysmon_supply_offset(chan->address);
+			sysmon_read_reg(sysmon, offset, val);
+			*val2 = 0;
+			ret = IIO_VAL_INT;
+			break;
+
+		default:
+			break;
+		}
+		break;
+
+	case IIO_CHAN_INFO_PROCESSED:
+		switch (chan->type) {
+		case IIO_TEMP:
+			/* In Deg C */
+			offset = sysmon_temp_offset(chan->address);
+			sysmon_read_reg(sysmon, offset, &regval);
+			sysmon_q8p7_to_celsius(regval, val, val2);
+			ret = IIO_VAL_FRACTIONAL;
+			break;
+
+		case IIO_VOLTAGE:
+			/* In Volts */
+			offset = sysmon_supply_offset(chan->address);
+			sysmon_read_reg(sysmon, offset, &regval);
+			sysmon_supply_rawtoprocessed(regval, val, val2);
+			ret = IIO_VAL_FRACTIONAL;
+			break;
+
+		default:
+			break;
+		}
+		break;
+
+	default:
+		break;
+	}
+
+	mutex_unlock(&sysmon->mutex);
+	return ret;
+}
+
+static int sysmon_get_event_mask(unsigned long address)
+{
+	if (address == TEMP_EVENT)
+		return BIT(SYSMON_BIT_TEMP);
+	else if (address == OT_EVENT)
+		return BIT(SYSMON_BIT_OT);
+
+	/* return supply */
+	return BIT(address / 32);
+}
+
+static int sysmon_read_alarm_config(struct sysmon *sysmon,
+				    unsigned long address)
+{
+	u32 reg_val;
+	u32 alarm_reg_num = ALARM_REG(address);
+	u32 shift = ALARM_SHIFT(address);
+	u32 offset = SYSMON_ALARM_REG + (4 * alarm_reg_num);
+
+	sysmon_read_reg(sysmon, offset, &reg_val);
+
+	return reg_val & BIT(shift);
+}
+
+static void sysmon_write_alarm_config(struct sysmon *sysmon,
+				      unsigned long address, u32 val)
+{
+	u32 alarm_reg_num = ALARM_REG(address);
+	u32 shift = ALARM_SHIFT(address);
+	u32 offset = SYSMON_ALARM_REG + (4 * alarm_reg_num);
+
+	sysmon_update_reg(sysmon, offset, BIT(shift), (val << shift));
+}
+
+static int sysmon_read_event_config(struct iio_dev *indio_dev,
+				    const struct iio_chan_spec *chan,
+				    enum iio_event_type type,
+				    enum iio_event_direction dir)
+{
+	struct sysmon *sysmon = iio_priv(indio_dev);
+	u32 config_value, imr;
+	u32 alarm_event_mask = sysmon_get_event_mask(chan->address);
+
+	sysmon_read_reg(sysmon, SYSMON_IMR, &imr);
+
+	/* Getting the unmasked interrupts */
+	imr = ~imr;
+
+	if (chan->type == IIO_VOLTAGE) {
+		config_value = sysmon_read_alarm_config(sysmon, chan->address);
+
+		return (config_value && (imr & alarm_event_mask));
+	}
+
+	return (imr & sysmon_get_event_mask(chan->address)) ? 1 : 0;
+}
+
+static int sysmon_write_event_config(struct iio_dev *indio_dev,
+				     const struct iio_chan_spec *chan,
+				     enum iio_event_type type,
+				     enum iio_event_direction dir, int state)
+{
+	struct sysmon *sysmon = iio_priv(indio_dev);
+	u32 alarm_reg_num = ALARM_REG(chan->address);
+	u32 offset = SYSMON_ALARM_REG + (4 * alarm_reg_num);
+	u32 ier = sysmon_get_event_mask(chan->address);
+	u32 alarm_config;
+	unsigned long flags;
+
+	mutex_lock(&sysmon->mutex);
+	spin_lock_irqsave(&sysmon->lock, flags);
+
+	if (chan->type == IIO_VOLTAGE) {
+		sysmon_write_alarm_config(sysmon, chan->address, state);
+
+		sysmon_read_reg(sysmon, offset, &alarm_config);
+
+		if (alarm_config)
+			sysmon_write_reg(sysmon, SYSMON_IER, ier);
+		else
+			sysmon_write_reg(sysmon, SYSMON_IDR, ier);
+	} else {
+		if (state) {
+			sysmon_write_reg(sysmon, SYSMON_IER, ier);
+			sysmon->temp_mask &= ~ier;
+		} else {
+			sysmon_write_reg(sysmon, SYSMON_IDR, ier);
+			sysmon->temp_mask |= ier;
+		}
+	}
+
+	spin_unlock_irqrestore(&sysmon->lock, flags);
+	mutex_unlock(&sysmon->mutex);
+
+	return 0;
+}
+
+static int sysmon_read_event_value(struct iio_dev *indio_dev,
+				   const struct iio_chan_spec *chan,
+				   enum iio_event_type type,
+				   enum iio_event_direction dir,
+				   enum iio_event_info info, int *val,
+				   int *val2)
+{
+	struct sysmon *sysmon = iio_priv(indio_dev);
+	u32 offset, reg_val;
+	u32 mask, shift;
+	u32 ret = -EINVAL;
+
+	mutex_lock(&sysmon->mutex);
+	if (chan->type == IIO_TEMP) {
+		if (info == IIO_EV_INFO_VALUE) {
+			offset = sysmon_temp_thresh_offset(chan->address, dir);
+			sysmon_read_reg(sysmon, offset, &reg_val);
+			sysmon_q8p7_to_celsius(reg_val, val, val2);
+			ret = IIO_VAL_FRACTIONAL;
+		} else if (info == IIO_EV_INFO_HYSTERESIS) {
+			mask = (chan->address == OT_EVENT) ? 0x1 : 0x2;
+			shift = mask - 1;
+			sysmon_read_reg(sysmon, SYSMON_TEMP_EV_CFG, &reg_val);
+			*val = (reg_val & mask) >> shift;
+			*val2 = 0;
+			ret = IIO_VAL_INT;
+		}
+	} else if (chan->type == IIO_VOLTAGE) {
+		offset = sysmon_supply_thresh_offset(chan->address, dir);
+		sysmon_read_reg(sysmon, offset, &reg_val);
+		sysmon_supply_rawtoprocessed(reg_val, val, val2);
+		ret = IIO_VAL_FRACTIONAL;
+	}
+
+	mutex_unlock(&sysmon->mutex);
+	return ret;
+}
+
+static int sysmon_write_event_value(struct iio_dev *indio_dev,
+				    const struct iio_chan_spec *chan,
+				    enum iio_event_type type,
+				    enum iio_event_direction dir,
+				    enum iio_event_info info, int val, int val2)
+{
+	struct sysmon *sysmon = iio_priv(indio_dev);
+	u32 offset, raw_val, reg_val;
+	u32 mask, shift;
+
+	mutex_lock(&sysmon->mutex);
+	if (chan->type == IIO_TEMP) {
+		if (info == IIO_EV_INFO_VALUE) {
+			offset = sysmon_temp_thresh_offset(chan->address, dir);
+			sysmon_celsius_to_q8p7(&reg_val, val, val2);
+			sysmon_write_reg(sysmon, offset, reg_val);
+		} else if (info == IIO_EV_INFO_HYSTERESIS) {
+			/* calculating the mask value for OT and TEMP Alarms */
+			mask = (chan->address == OT_EVENT) ? 1 : 2;
+			shift = mask - 1;
+			sysmon_update_reg(sysmon, SYSMON_TEMP_EV_CFG, mask,
+					  (val << shift));
+		}
+	} else if (chan->type == IIO_VOLTAGE) {
+		offset = sysmon_supply_thresh_offset(chan->address, dir);
+		sysmon_read_reg(sysmon, offset, &reg_val);
+		sysmon_supply_processedtoraw(val, val2, reg_val, &raw_val);
+		sysmon_write_reg(sysmon, offset, raw_val);
+	}
+
+	mutex_unlock(&sysmon->mutex);
+	return 0;
+}
+
+static const struct iio_info iio_dev_info = {
+	.read_raw = sysmon_read_raw,
+	.read_event_config = sysmon_read_event_config,
+	.write_event_config = sysmon_write_event_config,
+	.read_event_value = sysmon_read_event_value,
+	.write_event_value = sysmon_write_event_value,
+};
+
+/* sysmon instance for in kernel exported functions */
+static struct sysmon *g_sysmon;
+
+/**
+ * sysmon_register_temp_ops - register temperature based event handler for a
+ *			      given region.
+ * @cb: callback function pointer.
+ * @data: private data to be passed to the callback.
+ * @region_id: id of the region for which the callback is to be set.
+ * @return: 0 for success and negative number in case of failure.
+ */
+int sysmon_register_temp_ops(void (*cb)(void *data, struct regional_node *node),
+			     void *data, enum sysmon_region region_id)
+{
+	struct sysmon *sysmon = g_sysmon;
+	struct region_info *region;
+	int ret = 0, found = 0;
+
+	if (!cb || !sysmon)
+		return -EINVAL;
+
+	ret = mutex_lock_interruptible(&sysmon->mutex);
+	if (ret) {
+		dev_err(sysmon->dev, "Failed to acquire a lock. Process was interrupted by fatal signals");
+		return ret;
+	}
+
+	if (list_empty(&sysmon->region_list)) {
+		dev_err(sysmon->dev, "Failed to set a callback. HW node info missing in the device tree/ Not supported for this device");
+		ret = -EINVAL;
+		goto exit;
+	}
+
+	list_for_each_entry(region, &sysmon->region_list, list) {
+		if (region->id == region_id) {
+			found = 1;
+			if (region->cb) {
+				dev_err(sysmon->dev, "Error callback already set. Unregister the existing callback to set a new one.");
+				ret = -EINVAL;
+				goto exit;
+			}
+			region->cb = cb;
+			region->data = data;
+			break;
+		}
+	}
+
+	if (!found) {
+		dev_err(sysmon->dev, "Error invalid region. Please select the correct region");
+		ret = -EINVAL;
+	}
+
+exit:
+	mutex_unlock(&sysmon->mutex);
+	return ret;
+}
+EXPORT_SYMBOL(sysmon_register_temp_ops);
+
+/**
+ * sysmon_unregister_temp_ops - Unregister the callback for temperature
+ *				notification.
+ * @region_id: id of the region for which the callback is to be set.
+ * @return: 0 for success and negative number in case of failure.
+ */
+int sysmon_unregister_temp_ops(enum sysmon_region region_id)
+{
+	struct sysmon *sysmon = g_sysmon;
+	struct region_info *region;
+	int ret = 0, found = 0;
+
+	if (!sysmon)
+		return -EINVAL;
+
+	ret = mutex_lock_interruptible(&sysmon->mutex);
+	if (ret) {
+		dev_err(sysmon->dev, "Failed to acquire a lock. Process was interrupted by fatal signals");
+		return ret;
+	}
+
+	if (list_empty(&sysmon->region_list)) {
+		dev_err(sysmon->dev, "Failed to set a callback. HW node info missing in the device tree/ Not supported for this device");
+		ret = -EINVAL;
+		goto exit;
+	}
+
+	list_for_each_entry(region, &sysmon->region_list, list) {
+		if (region->id == region_id) {
+			found = 1;
+			region->cb = NULL;
+			region->data = NULL;
+			break;
+		}
+	}
+
+	if (!found) {
+		dev_err(sysmon->dev, "Error no such region. Please select the correct region");
+		ret = -EINVAL;
+	}
+
+exit:
+	mutex_unlock(&sysmon->mutex);
+	return ret;
+}
+EXPORT_SYMBOL(sysmon_unregister_temp_ops);
+
+/**
+ * sysmon_nodes_by_region - returns the nodes list for a particular region.
+ * @region_id: id for the region for which nodes are requested.
+ * @return: Pointer to the linked list or NULL if region is not present.
+ */
+struct list_head *sysmon_nodes_by_region(enum sysmon_region region_id)
+{
+	struct sysmon *sysmon = g_sysmon;
+	struct region_info *region;
+
+	if (!sysmon)
+		return NULL;
+
+	list_for_each_entry(region, &sysmon->region_list, list) {
+		if (region->id == region_id)
+			return &region->node_list;
+	}
+
+	dev_err(sysmon->dev, "Error invalid region. Please select the correct region");
+
+	return NULL;
+}
+EXPORT_SYMBOL(sysmon_nodes_by_region);
+
+/**
+ * sysmon_get_node_value - returns value of the sensor at a node.
+ * @sat_id: id of the node.
+ * @return: -EINVAL if not initialized or returns raw value of the sensor.
+ */
+int sysmon_get_node_value(int sat_id)
+{
+	struct sysmon *sysmon = g_sysmon;
+	u32 raw;
+
+	if (!sysmon)
+		return -EINVAL;
+
+	sysmon_read_reg(sysmon, SYSMON_NODE_OFFSET, &raw);
+
+	return raw;
+}
+EXPORT_SYMBOL(sysmon_get_node_value);
+
+static void sysmon_push_event(struct iio_dev *indio_dev, u32 address)
+{
+	u32 i;
+	const struct iio_chan_spec *chan;
+
+	for (i = 0; i < indio_dev->num_channels; i++) {
+		if (indio_dev->channels[i].address == address) {
+			chan = &indio_dev->channels[i];
+			iio_push_event(indio_dev,
+				       IIO_UNMOD_EVENT_CODE(chan->type,
+							    chan->channel,
+							    IIO_EV_TYPE_THRESH,
+							    IIO_EV_DIR_EITHER),
+				       iio_get_time_ns(indio_dev));
+		}
+	}
+}
+
+static void sysmon_region_event_handler(struct sysmon *sysmon)
+{
+	struct region_info *region;
+	struct regional_node *node, *eventnode;
+	u32 regval, event = 0;
+	u16 thresh_up, val;
+
+	sysmon_read_reg(sysmon, SYSMON_TEMP_TH_UP, &regval);
+	thresh_up = (u16)regval;
+
+	list_for_each_entry(region, &sysmon->region_list, list) {
+		list_for_each_entry(node, &region->node_list,
+				    regional_node_list) {
+			val = sysmon_get_node_value(node->sat_id);
+
+			/* Find the highest value */
+			if (compare(val, thresh_up)) {
+				eventnode = node;
+				eventnode->temp = val;
+				thresh_up = val;
+				event = 1;
+			}
+		}
+		if (event && region->cb)
+			region->cb(region->data, eventnode);
+	}
+}
+
+static void sysmon_handle_event(struct iio_dev *indio_dev, u32 event)
+{
+	struct sysmon *sysmon = iio_priv(indio_dev);
+	unsigned long alarm_flag_reg;
+	u32 address, bit, reg_val;
+	u32 alarm_flag_offset = SYSMON_ALARM_FLAG + (event * 4);
+	u32 alarm_reg_offset = SYSMON_ALARM_REG + (event * 4);
+
+	switch (event) {
+	case SYSMON_BIT_TEMP:
+		address = TEMP_EVENT;
+		sysmon_push_event(indio_dev, address);
+		sysmon_write_reg(sysmon, SYSMON_IDR, BIT(SYSMON_BIT_TEMP));
+		sysmon->masked_temp |= BIT(SYSMON_BIT_TEMP);
+		sysmon_region_event_handler(sysmon);
+		break;
+
+	case SYSMON_BIT_OT:
+		address = OT_EVENT;
+		sysmon_push_event(indio_dev, address);
+		sysmon_write_reg(sysmon, SYSMON_IDR, BIT(SYSMON_BIT_OT));
+		sysmon->masked_temp |= BIT(SYSMON_BIT_OT);
+		sysmon_region_event_handler(sysmon);
+		break;
+
+	case SYSMON_BIT_ALARM4:
+	case SYSMON_BIT_ALARM3:
+	case SYSMON_BIT_ALARM2:
+	case SYSMON_BIT_ALARM1:
+	case SYSMON_BIT_ALARM0:
+		/* Read enabled alarms */
+		sysmon_read_reg(sysmon, alarm_flag_offset, &reg_val);
+		alarm_flag_reg = (unsigned long)reg_val;
+
+		for_each_set_bit(bit, &alarm_flag_reg, 32) {
+			address = bit + (32 * event);
+			sysmon_push_event(indio_dev, address);
+			/* disable alarm */
+			sysmon_update_reg(sysmon, alarm_reg_offset, BIT(bit),
+					  0);
+		}
+		/* clear alarms */
+		sysmon_write_reg(sysmon, alarm_flag_offset, alarm_flag_reg);
+		break;
+
+	default:
+		break;
+	}
+}
+
+static void sysmon_handle_events(struct iio_dev *indio_dev,
+				 unsigned long events)
+{
+	unsigned int bit;
+
+	for_each_set_bit(bit, &events, SYSMON_NO_OF_EVENTS)
+		sysmon_handle_event(indio_dev, bit);
+}
+
+static void sysmon_unmask_temp(struct sysmon *sysmon, unsigned int isr)
+{
+	unsigned int unmask, status;
+
+	status = isr & SYSMON_TEMP_MASK;
+
+	/* clear bits that are not active any more */
+	unmask = (sysmon->masked_temp ^ status) & sysmon->masked_temp;
+	sysmon->masked_temp &= status;
+
+	/* clear status of disabled alarm */
+	unmask &= ~sysmon->temp_mask;
+
+	sysmon_write_reg(sysmon, SYSMON_IER, unmask);
+}
+
+/*
+ * The Versal threshold interrupts are level sensitive. Since we can't make the
+ * threshold condition go way from within the interrupt handler, this means as
+ * soon as a threshold condition is present we would enter the interrupt handler
+ * again and again. To work around this we mask all active thresholds interrupts
+ * in the interrupt handler and start a timer. In this timer we poll the
+ * interrupt status and only if the interrupt is inactive we unmask it again.
+ */
+static void sysmon_unmask_worker(struct work_struct *work)
+{
+	struct sysmon *sysmon = container_of(work, struct sysmon,
+					     sysmon_unmask_work.work);
+	unsigned int isr;
+
+	spin_lock_irq(&sysmon->lock);
+
+	/* Read the current interrupt status */
+	sysmon_read_reg(sysmon, SYSMON_ISR, &isr);
+
+	/* Clear interrupts */
+	sysmon_write_reg(sysmon, SYSMON_ISR, isr);
+
+	sysmon_unmask_temp(sysmon, isr);
+
+	spin_unlock_irq(&sysmon->lock);
+
+	/* if still pending some alarm re-trigger the timer */
+	if (sysmon->masked_temp)
+		schedule_delayed_work(&sysmon->sysmon_unmask_work,
+				      msecs_to_jiffies(SYSMON_UNMASK_WORK_DELAY_MS));
+	else
+		/*
+		 * Reset the temp_max_max and temp_min_min values to reset the
+		 * previously reached high/low values during an alarm.
+		 * This will enable the user to see the high/low values attained
+		 * during an event
+		 */
+		sysmon_write_reg(sysmon, SYSMON_STATUS_RESET, 1);
+}
+
+static irqreturn_t sysmon_iio_irq(int irq, void *data)
+{
+	u32 isr, imr;
+	struct iio_dev *indio_dev = data;
+	struct sysmon *sysmon = iio_priv(indio_dev);
+
+	spin_lock(&sysmon->lock);
+
+	sysmon_read_reg(sysmon, SYSMON_ISR, &isr);
+	sysmon_read_reg(sysmon, SYSMON_IMR, &imr);
+
+	/* only process alarm that are not masked */
+	isr &= ~imr;
+
+	/* clear interrupt */
+	sysmon_write_reg(sysmon, SYSMON_ISR, isr);
+
+	if (isr) {
+		sysmon_handle_events(indio_dev, isr);
+
+		schedule_delayed_work(&sysmon->sysmon_unmask_work,
+				      msecs_to_jiffies(SYSMON_UNMASK_WORK_DELAY_MS));
+	}
+
+	spin_unlock(&sysmon->lock);
+
+	return IRQ_HANDLED;
+}
+
+static void sysmon_events_worker(struct work_struct *work)
+{
+	u32 isr, imr;
+	struct sysmon *sysmon = container_of(work, struct sysmon,
+					     sysmon_events_work.work);
+
+	spin_lock(&sysmon->lock);
+
+	sysmon_read_reg(sysmon, SYSMON_ISR, &isr);
+	sysmon_read_reg(sysmon, SYSMON_IMR, &imr);
+
+	/* only process alarm that are not masked */
+	isr &= ~imr;
+
+	/* clear interrupt */
+	sysmon_write_reg(sysmon, SYSMON_ISR, isr);
+
+	if (isr) {
+		sysmon_handle_events(sysmon->indio_dev, isr);
+		schedule_delayed_work(&sysmon->sysmon_unmask_work,
+				      msecs_to_jiffies(SYSMON_UNMASK_WORK_DELAY_MS));
+	}
+	spin_unlock(&sysmon->lock);
+
+	schedule_delayed_work(&sysmon->sysmon_events_work,
+			      msecs_to_jiffies(SYSMON_EVENT_WORK_DELAY_MS));
+}
+
+static int get_hw_node_properties(struct platform_device *pdev,
+				  struct list_head *region_list)
+{
+	struct region_info *region = NULL;
+	struct regional_node *nodes;
+	struct device_node *np = pdev->dev.of_node;
+	int size;
+	u32 id, satid, x, y, i, offset, prev = 0;
+
+	/* get hw-node-info */
+	if (!of_get_property(np, "hw-node", &size))
+		return 0;
+
+	if (size % 16) {
+		dev_info(&pdev->dev, "HW-Node properties not correct");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < (size / 16); i++) {
+		offset = i * 4;
+		of_property_read_u32_index(np, "hw-node", offset, &id);
+		of_property_read_u32_index(np, "hw-node", offset + 1, &satid);
+		of_property_read_u32_index(np, "hw-node", offset + 2, &x);
+		of_property_read_u32_index(np, "hw-node", offset + 3, &y);
+
+		if (list_empty(region_list) || prev != id) {
+			region = devm_kzalloc(&pdev->dev, sizeof(*region),
+					      GFP_KERNEL);
+			if (!region)
+				return -ENOMEM;
+
+			region->id = id;
+			INIT_LIST_HEAD(&region->node_list);
+			list_add(&region->list, region_list);
+		}
+
+		prev = id;
+		nodes = devm_kzalloc(&pdev->dev, sizeof(*nodes), GFP_KERNEL);
+		if (!nodes)
+			return -ENOMEM;
+		nodes->sat_id = satid;
+		nodes->x = x;
+		nodes->y = y;
+		list_add(&nodes->regional_node_list, &region->node_list);
+	}
+
+	return 0;
+}
+
+static int sysmon_parse_dt(struct iio_dev *indio_dev,
+			   struct platform_device *pdev)
+{
+	struct sysmon *sysmon;
+	struct iio_chan_spec *sysmon_channels;
+	struct device_node *child_node = NULL, *np = pdev->dev.of_node;
+	int ret, i = 0;
+	u8 num_supply_chan = 0;
+	u32 reg = 0, num_temp_chan = 0;
+	const char *name;
+	u32 chan_size = sizeof(struct iio_chan_spec);
+	u32 temp_chan_size;
+
+	sysmon = iio_priv(indio_dev);
+	ret = of_property_read_u8(np, "xlnx,numchannels", &num_supply_chan);
+	if (ret < 0)
+		return ret;
+
+	INIT_LIST_HEAD(&sysmon->region_list);
+
+	if (sysmon->irq > 0)
+		get_hw_node_properties(pdev, &sysmon->region_list);
+
+	/* Initialize buffer for channel specification */
+	temp_chan_size = (sizeof(temp_channels) + sizeof(temp_events));
+
+	num_temp_chan = ARRAY_SIZE(temp_channels);
+
+	sysmon_channels = devm_kzalloc(&pdev->dev,
+				       (chan_size * num_supply_chan) +
+				       temp_chan_size, GFP_KERNEL);
+
+	for_each_child_of_node(np, child_node) {
+		ret = of_property_read_u32(child_node, "reg", &reg);
+		if (ret < 0)
+			return ret;
+
+		ret = of_property_read_string(child_node, "xlnx,name", &name);
+		if (ret < 0)
+			return ret;
+
+		sysmon_channels[i].type = IIO_VOLTAGE;
+		sysmon_channels[i].indexed = 1;
+		sysmon_channels[i].address = reg;
+		sysmon_channels[i].channel = reg;
+		sysmon_channels[i].info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_PROCESSED);
+
+		sysmon_channels[i].event_spec = sysmon_supply_events;
+		sysmon_channels[i].num_event_specs = ARRAY_SIZE(sysmon_supply_events);
+
+		sysmon_channels[i].scan_index = i;
+		sysmon_channels[i].scan_type.realbits = 19;
+		sysmon_channels[i].scan_type.storagebits = 32;
+
+		sysmon_channels[i].scan_type.endianness = IIO_CPU;
+		sysmon_channels[i].extend_name = name;
+
+		if (of_property_read_bool(child_node, "xlnx,bipolar"))
+			sysmon_channels[i].scan_type.sign = 's';
+		else
+			sysmon_channels[i].scan_type.sign = 'u';
+
+		i++;
+	}
+
+	/* Append static temperature channels to the channel list */
+	memcpy(sysmon_channels + num_supply_chan, temp_channels,
+	       sizeof(temp_channels));
+	indio_dev->num_channels = num_supply_chan + ARRAY_SIZE(temp_channels);
+
+	memcpy(sysmon_channels + num_supply_chan + num_temp_chan,
+	       temp_events, sizeof(temp_events));
+	indio_dev->num_channels += ARRAY_SIZE(temp_events);
+
+	indio_dev->channels = sysmon_channels;
+
+	return 0;
+}
+
+static void sysmon_init_interrupt(struct sysmon *sysmon)
+{
+	u32 imr;
+
+	/* Read default Interrupt Mask */
+	sysmon_read_reg(sysmon, SYSMON_IMR, &imr);
+	sysmon->temp_mask = imr & SYSMON_TEMP_MASK;
+}
+
+static int sysmon_probe(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev;
+	struct sysmon *sysmon;
+	struct resource *mem;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*sysmon));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	sysmon = iio_priv(indio_dev);
+
+	sysmon->dev = &pdev->dev;
+	sysmon->indio_dev = indio_dev;
+
+	mutex_init(&sysmon->mutex);
+	spin_lock_init(&sysmon->lock);
+
+	indio_dev->dev.parent = &pdev->dev;
+	indio_dev->dev.of_node = pdev->dev.of_node;
+	indio_dev->name = "xlnx,versal-sysmon";
+	indio_dev->info = &iio_dev_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	sysmon->base = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(sysmon->base))
+		return PTR_ERR(sysmon->base);
+
+	if (secure_mode) {
+		ret = zynqmp_pm_feature(PM_IOCTL);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "Feature check failed with %d\n", ret);
+			return ret;
+		}
+		if ((ret & FIRMWARE_VERSION_MASK) < PM_API_VERSION_2) {
+			dev_err(&pdev->dev, "IOCTL firmware version error. Expected: v%d - Found: v%d\n",
+				PM_API_VERSION_2, ret & FIRMWARE_VERSION_MASK);
+			return -EOPNOTSUPP;
+		}
+		sysmon->ops = &secure_access;
+	} else {
+		sysmon->ops = &direct_access;
+	}
+
+	sysmon_write_reg(sysmon, SYSMON_NPI_LOCK, NPI_UNLOCK);
+
+	sysmon->irq = platform_get_irq_optional(pdev, 0);
+
+	ret = sysmon_parse_dt(indio_dev, pdev);
+	if (ret)
+		return ret;
+
+	INIT_DELAYED_WORK(&sysmon->sysmon_unmask_work,
+			  sysmon_unmask_worker);
+	sysmon_init_interrupt(sysmon);
+	if (sysmon->irq > 0) {
+		g_sysmon = sysmon;
+		ret = devm_request_irq(&pdev->dev, sysmon->irq, &sysmon_iio_irq,
+				       0, "sysmon-irq", indio_dev);
+		if (ret < 0)
+			return ret;
+	} else if (sysmon->irq == -EPROBE_DEFER) {
+		return -EPROBE_DEFER;
+	} else {
+		INIT_DELAYED_WORK(&sysmon->sysmon_events_work,
+				  sysmon_events_worker);
+		schedule_delayed_work(&sysmon->sysmon_events_work,
+				      msecs_to_jiffies(SYSMON_EVENT_WORK_DELAY_MS));
+	}
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	ret = iio_device_register(indio_dev);
+	if (ret < 0)
+		return ret;
+
+	dev_info(&pdev->dev, "Successfully registered Versal Sysmon");
+
+	return 0;
+}
+
+static int sysmon_remove(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct sysmon *sysmon = iio_priv(indio_dev);
+
+	/* cancel SSIT based events */
+	if (sysmon->irq < 0)
+		cancel_delayed_work_sync(&sysmon->sysmon_events_work);
+
+	cancel_delayed_work_sync(&sysmon->sysmon_unmask_work);
+
+	/* Unregister the device */
+	iio_device_unregister(indio_dev);
+	return 0;
+}
+
+static int sysmon_resume(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct sysmon *sysmon = iio_priv(indio_dev);
+
+	sysmon_write_reg(sysmon, SYSMON_NPI_LOCK, NPI_UNLOCK);
+
+	return 0;
+}
+
+static const struct of_device_id sysmon_of_match_table[] = {
+	{ .compatible = "xlnx,versal-sysmon" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, sysmon_of_match_table);
+
+static struct platform_driver sysmon_driver = {
+	.probe = sysmon_probe,
+	.remove = sysmon_remove,
+	.resume = sysmon_resume,
+	.driver = {
+		.name = "sysmon",
+		.of_match_table = sysmon_of_match_table,
+	},
+};
+module_platform_driver(sysmon_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Xilinx Versal SysMon Driver");
+MODULE_AUTHOR("Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/versal-sysmon.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/versal-sysmon.h
@@ -0,0 +1,183 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx SYSMON for Versal
+ *
+ * Copyright (C) 2019 - 2021 Xilinx, Inc.
+ *
+ * Description:
+ * This driver is developed for SYSMON on Versal. The driver supports INDIO Mode
+ * and supports voltage and temperature monitoring via IIO sysfs interface.
+ */
+
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/events.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/adc/versal-sysmon-events.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of_address.h>
+
+/* Channel IDs for Temp Channels */
+/* TEMP_MAX gives the current temperature for Production
+ * silicon.
+ * TEMP_MAX gives the current maximum temperature for ES1
+ * silicon.
+ */
+#define TEMP_MAX	160
+
+/* TEMP_MIN is not applicable for Production silicon.
+ * TEMP_MIN gives the current minimum temperature for ES1 silicon.
+ */
+#define TEMP_MIN	161
+
+#define TEMP_MAX_MAX	162
+#define TEMP_MIN_MIN	163
+#define TEMP_EVENT	164
+#define OT_EVENT	165
+
+/* Register Unlock Code */
+#define NPI_UNLOCK	0xF9E8D7C6
+
+/* Register Offsets */
+#define SYSMON_NPI_LOCK		0x000C
+#define SYSMON_ISR		0x0044
+#define SYSMON_TEMP_MASK	0x300
+#define SYSMON_IMR		0x0048
+#define SYSMON_IER		0x004C
+#define SYSMON_IDR		0x0050
+#define SYSMON_ALARM_FLAG	0x1018
+#define SYSMON_TEMP_MAX		0x1030
+#define SYSMON_TEMP_MIN		0x1034
+#define SYSMON_SUPPLY_BASE	0x1040
+#define SYSMON_ALARM_REG	0x1940
+#define SYSMON_TEMP_TH_LOW	0x1970
+#define SYSMON_TEMP_TH_UP	0x1974
+#define SYSMON_OT_TH_LOW	0x1978
+#define SYSMON_OT_TH_UP		0x197C
+#define SYSMON_SUPPLY_TH_LOW	0x1980
+#define SYSMON_SUPPLY_TH_UP	0x1C80
+#define SYSMON_TEMP_MAX_MAX	0x1F90
+#define SYSMON_TEMP_MIN_MIN	0x1F8C
+#define SYSMON_TEMP_EV_CFG	0x1F84
+#define SYSMON_NODE_OFFSET	0x1FAC
+#define SYSMON_STATUS_RESET	0x1F94
+
+#define SYSMON_NO_OF_EVENTS	32
+
+/* Supply Voltage Conversion macros */
+#define SYSMON_MANTISSA_MASK		0xFFFF
+#define SYSMON_FMT_MASK			0x10000
+#define SYSMON_FMT_SHIFT		16
+#define SYSMON_MODE_MASK		0x60000
+#define SYSMON_MODE_SHIFT		17
+#define SYSMON_MANTISSA_SIGN_SHIFT	15
+#define SYSMON_UPPER_SATURATION_SIGNED	32767
+#define SYSMON_LOWER_SATURATION_SIGNED	-32768
+#define SYSMON_UPPER_SATURATION		65535
+#define SYSMON_LOWER_SATURATION		0
+
+#define SYSMON_CHAN_TEMP_EVENT(_address, _ext, _events) { \
+	.type = IIO_TEMP, \
+	.indexed = 1, \
+	.address = _address, \
+	.channel = _address, \
+	.event_spec = _events, \
+	.num_event_specs = ARRAY_SIZE(_events), \
+	.scan_type = { \
+		.sign = 's', \
+		.realbits = 15, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	}, \
+	.extend_name = _ext, \
+	}
+
+#define SYSMON_CHAN_TEMP(_address, _ext) { \
+	.type = IIO_TEMP, \
+	.indexed = 1, \
+	.address = _address, \
+	.channel = _address, \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+		BIT(IIO_CHAN_INFO_PROCESSED), \
+	.scan_type = { \
+		.sign = 's', \
+		.realbits = 15, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	}, \
+	.extend_name = _ext, \
+}
+
+#define twoscomp(val) ((((val) ^ 0xFFFF) + 1) & 0x0000FFFF)
+#define ALARM_REG(address) ((address) / 32)
+#define ALARM_SHIFT(address) ((address) % 32)
+
+#define compare(val, thresh) (((val) & 0x8000) || ((thresh) & 0x8000) ? \
+			      ((val) < (thresh)) : ((val) > (thresh)))  \
+
+enum sysmon_alarm_bit {
+	SYSMON_BIT_ALARM0 = 0,
+	SYSMON_BIT_ALARM1 = 1,
+	SYSMON_BIT_ALARM2 = 2,
+	SYSMON_BIT_ALARM3 = 3,
+	SYSMON_BIT_ALARM4 = 4,
+	SYSMON_BIT_ALARM5 = 5,
+	SYSMON_BIT_ALARM6 = 6,
+	SYSMON_BIT_ALARM7 = 7,
+	SYSMON_BIT_OT = 8,
+	SYSMON_BIT_TEMP = 9,
+};
+
+/**
+ * struct sysmon - Driver data for Sysmon
+ * @base: physical base address of device
+ * @dev: pointer to device struct
+ * @indio_dev: pointer to the iio device
+ * @mutex: to handle multiple user interaction
+ * @lock: to help manage interrupt registers correctly
+ * @irq: interrupt number of the sysmon
+ * @region_list: list of the regions of sysmon
+ * @masked_temp: currently masked due to alarm
+ * @temp_mask: temperature based interrupt configuration
+ * @sysmon_unmask_work: re-enables event once the event condition disappears
+ * @sysmon_events_work: poll for events on SSIT slices
+ * @ops: read write operations for sysmon registers
+ *
+ * This structure contains necessary state for Sysmon driver to operate
+ */
+struct sysmon {
+	void __iomem *base;
+	struct device *dev;
+	struct iio_dev *indio_dev;
+	/* kernel doc above */
+	struct mutex mutex;
+	/* kernel doc above*/
+	spinlock_t lock;
+	int irq;
+	struct list_head region_list;
+	unsigned int masked_temp;
+	unsigned int temp_mask;
+	struct delayed_work sysmon_unmask_work;
+	struct delayed_work sysmon_events_work;
+	struct sysmon_ops *ops;
+};
+
+struct sysmon_ops {
+	void (*read_reg)(struct sysmon *sysmon, u32 offset, u32 *data);
+	void (*write_reg)(struct sysmon *sysmon, u32 offset, u32 data);
+	void (*update_reg)(struct sysmon *sysmon, u32 offset,
+			   u32 mask, u32 data);
+};
+
+int sysmon_register_temp_ops(void (*cb)(void *data, struct regional_node *node),
+			     void *data, enum sysmon_region region_id);
+int sysmon_unregister_temp_ops(enum sysmon_region region_id);
+struct list_head *sysmon_nodes_by_region(enum sysmon_region region_id);
+int sysmon_get_node_value(int sat_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/xilinx-ams.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/xilinx-ams.c
@@ -0,0 +1,1116 @@
+/*
+ * Xilinx AMS driver
+ *
+ * Licensed under the GPL-2
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/of_address.h>
+#include <linux/iopoll.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/events.h>
+#include <linux/iio/buffer.h>
+#include <linux/io.h>
+
+#include "xilinx-ams.h"
+#include <linux/delay.h>
+
+static const unsigned int AMS_UNMASK_TIMEOUT = 500;
+
+static inline void ams_read_reg(struct ams *ams, unsigned int offset, u32 *data)
+{
+	*data = readl(ams->base + offset);
+}
+
+static inline void ams_write_reg(struct ams *ams, unsigned int offset, u32 data)
+{
+	writel(data, ams->base + offset);
+}
+
+static inline void ams_update_reg(struct ams *ams, unsigned int offset,
+				  u32 mask, u32 data)
+{
+	u32 val;
+
+	ams_read_reg(ams, offset, &val);
+	ams_write_reg(ams, offset, (val & ~mask) | (mask & data));
+}
+
+static inline void ams_ps_read_reg(struct ams *ams, unsigned int offset,
+				   u32 *data)
+{
+	*data = readl(ams->ps_base + offset);
+}
+
+static inline void ams_ps_write_reg(struct ams *ams, unsigned int offset,
+				    u32 data)
+{
+	writel(data, ams->ps_base + offset);
+}
+
+static inline void ams_ps_update_reg(struct ams *ams, unsigned int offset,
+				     u32 mask, u32 data)
+{
+	u32 val;
+
+	ams_ps_read_reg(ams, offset, &val);
+	ams_ps_write_reg(ams, offset, (val & ~mask) | (data & mask));
+}
+
+static inline void ams_apb_pl_read_reg(struct ams *ams, unsigned int offset,
+				       u32 *data)
+{
+	*data = readl(ams->pl_base + offset);
+}
+
+static inline void ams_apb_pl_write_reg(struct ams *ams, unsigned int offset,
+					u32 data)
+{
+	writel(data, ams->pl_base + offset);
+}
+
+static inline void ams_apb_pl_update_reg(struct ams *ams, unsigned int offset,
+					 u32 mask, u32 data)
+{
+	u32 val;
+
+	ams_apb_pl_read_reg(ams, offset, &val);
+	ams_apb_pl_write_reg(ams, offset, (val & ~mask) | (data & mask));
+}
+
+static void ams_update_intrmask(struct ams *ams, u64 mask, u64 val)
+{
+	/* intr_mask variable in ams represent bit in AMS regisetr IDR0 and IDR1
+	 * first 32 biit will be of IDR0, next one are of IDR1 register.
+	 */
+	ams->intr_mask &= ~mask;
+	ams->intr_mask |= (val & mask);
+
+	ams_write_reg(ams, AMS_IER_0, ~(ams->intr_mask | ams->masked_alarm));
+	ams_write_reg(ams, AMS_IER_1,
+		      ~(ams->intr_mask >> AMS_ISR1_INTR_MASK_SHIFT));
+	ams_write_reg(ams, AMS_IDR_0, ams->intr_mask | ams->masked_alarm);
+	ams_write_reg(ams, AMS_IDR_1,
+		      ams->intr_mask >> AMS_ISR1_INTR_MASK_SHIFT);
+}
+
+static void iio_ams_disable_all_alarm(struct ams *ams)
+{
+	/* disable PS module alarm */
+	if (ams->ps_base) {
+		ams_ps_update_reg(ams, AMS_REG_CONFIG1, AMS_REGCFG1_ALARM_MASK,
+				  AMS_REGCFG1_ALARM_MASK);
+		ams_ps_update_reg(ams, AMS_REG_CONFIG3, AMS_REGCFG3_ALARM_MASK,
+				  AMS_REGCFG3_ALARM_MASK);
+	}
+
+	/* disable PL module alarm */
+	if (ams->pl_base) {
+		ams->pl_bus->update(ams, AMS_REG_CONFIG1,
+				    AMS_REGCFG1_ALARM_MASK,
+				    AMS_REGCFG1_ALARM_MASK);
+		ams->pl_bus->update(ams, AMS_REG_CONFIG3,
+				    AMS_REGCFG3_ALARM_MASK,
+				    AMS_REGCFG3_ALARM_MASK);
+	}
+}
+
+static void iio_ams_update_alarm(struct ams *ams, unsigned long alarm_mask)
+{
+	u32 cfg;
+	unsigned long flags;
+	unsigned long pl_alarm_mask;
+
+	if (ams->ps_base) {
+		/* Configuring PS alarm enable */
+		cfg = ~((alarm_mask & AMS_ISR0_ALARM_2_TO_0_MASK) <<
+			       AMS_CONF1_ALARM_2_TO_0_SHIFT);
+		cfg &= ~((alarm_mask & AMS_ISR0_ALARM_6_TO_3_MASK) <<
+				AMS_CONF1_ALARM_6_TO_3_SHIFT);
+		ams_ps_update_reg(ams, AMS_REG_CONFIG1, AMS_REGCFG1_ALARM_MASK,
+				  cfg);
+
+		cfg = ~((alarm_mask >> AMS_CONF3_ALARM_12_TO_7_SHIFT) &
+				AMS_ISR0_ALARM_12_TO_7_MASK);
+		ams_ps_update_reg(ams, AMS_REG_CONFIG3, AMS_REGCFG3_ALARM_MASK,
+				  cfg);
+	}
+
+	if (ams->pl_base) {
+		pl_alarm_mask = (alarm_mask >> AMS_PL_ALARM_START);
+		/* Configuring PL alarm enable */
+		cfg = ~((pl_alarm_mask & AMS_ISR0_ALARM_2_TO_0_MASK) <<
+			       AMS_CONF1_ALARM_2_TO_0_SHIFT);
+		cfg &= ~((pl_alarm_mask & AMS_ISR0_ALARM_6_TO_3_MASK) <<
+				AMS_CONF1_ALARM_6_TO_3_SHIFT);
+		ams->pl_bus->update(ams, AMS_REG_CONFIG1,
+				AMS_REGCFG1_ALARM_MASK, cfg);
+
+		cfg = ~((pl_alarm_mask >> AMS_CONF3_ALARM_12_TO_7_SHIFT) &
+				AMS_ISR0_ALARM_12_TO_7_MASK);
+		ams->pl_bus->update(ams, AMS_REG_CONFIG3,
+				AMS_REGCFG3_ALARM_MASK, cfg);
+	}
+
+	spin_lock_irqsave(&ams->lock, flags);
+	ams_update_intrmask(ams, AMS_ISR0_ALARM_MASK, ~alarm_mask);
+	spin_unlock_irqrestore(&ams->lock, flags);
+}
+
+static void ams_enable_channel_sequence(struct ams *ams)
+{
+	int i;
+	unsigned long long scan_mask;
+	struct iio_dev *indio_dev = ams->indio_dev;
+
+	/* Enable channel sequence. First 22 bit of scan_mask represent
+	 * PS channels, and  next remaining bit represents PL channels.
+	 */
+
+	/* Run calibration of PS & PL as part of the sequence */
+	scan_mask = 1 | (1 << PS_SEQ_MAX);
+	for (i = 0; i < indio_dev->num_channels; i++)
+		if (indio_dev->channels[i].scan_index < PL_SEQ_MAX)
+			scan_mask |= BIT(indio_dev->channels[i].scan_index);
+
+	if (ams->ps_base) {
+		/* put sysmon in a soft reset to change the sequence */
+		ams_ps_update_reg(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+				  AMS_CONF1_SEQ_DEFAULT);
+
+		/* configure basic channels */
+		ams_ps_write_reg(ams, AMS_REG_SEQ_CH0,
+				 scan_mask & AMS_REG_SEQ0_MASK);
+		ams_ps_write_reg(ams, AMS_REG_SEQ_CH2, AMS_REG_SEQ2_MASK &
+				(scan_mask >> AMS_REG_SEQ2_MASK_SHIFT));
+
+		/* set continuous sequence mode */
+		ams_ps_update_reg(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+				  AMS_CONF1_SEQ_CONTINUOUS);
+	}
+
+	if (ams->pl_base) {
+		/* put sysmon in a soft reset to change the sequence */
+		ams->pl_bus->update(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+				    AMS_CONF1_SEQ_DEFAULT);
+
+		/* configure basic channels */
+		scan_mask = (scan_mask >> PS_SEQ_MAX);
+		ams->pl_bus->write(ams, AMS_REG_SEQ_CH0,
+				scan_mask & AMS_REG_SEQ0_MASK);
+		ams->pl_bus->write(ams, AMS_REG_SEQ_CH2, AMS_REG_SEQ2_MASK &
+				(scan_mask >> AMS_REG_SEQ2_MASK_SHIFT));
+		ams->pl_bus->write(ams, AMS_REG_SEQ_CH1, AMS_REG_SEQ1_MASK &
+				(scan_mask >> AMS_REG_SEQ1_MASK_SHIFT));
+
+		/* set continuous sequence mode */
+		ams->pl_bus->update(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+				AMS_CONF1_SEQ_CONTINUOUS);
+	}
+}
+
+static int iio_ams_init_device(struct ams *ams)
+{
+	int ret = 0;
+	u32 reg;
+
+	/* reset AMS */
+	if (ams->ps_base) {
+		ams_ps_write_reg(ams, AMS_VP_VN, AMS_PS_RESET_VALUE);
+
+		ret = readl_poll_timeout(ams->base + AMS_PS_CSTS, reg,
+					 (reg & AMS_PS_CSTS_PS_READY) ==
+					 AMS_PS_CSTS_PS_READY, 0,
+					 AMS_INIT_TIMEOUT);
+		if (ret)
+			return ret;
+
+		/* put sysmon in a default state */
+		ams_ps_update_reg(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+				  AMS_CONF1_SEQ_DEFAULT);
+	}
+
+	if (ams->pl_base) {
+		ams->pl_bus->write(ams, AMS_VP_VN, AMS_PL_RESET_VALUE);
+
+		ret = readl_poll_timeout(ams->base + AMS_PL_CSTS, reg,
+					 (reg & AMS_PL_CSTS_ACCESS_MASK) ==
+					 AMS_PL_CSTS_ACCESS_MASK, 0,
+					 AMS_INIT_TIMEOUT);
+		if (ret)
+			return ret;
+
+		/* put sysmon in a default state */
+		ams->pl_bus->update(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+				    AMS_CONF1_SEQ_DEFAULT);
+	}
+
+	iio_ams_disable_all_alarm(ams);
+
+	/* Disable interrupt */
+	ams_update_intrmask(ams, ~0, ~0);
+
+	/* Clear any pending interrupt */
+	ams_write_reg(ams, AMS_ISR_0, AMS_ISR0_ALARM_MASK);
+	ams_write_reg(ams, AMS_ISR_1, AMS_ISR1_ALARM_MASK);
+
+	return ret;
+}
+
+static void ams_enable_single_channel(struct ams *ams, unsigned int offset)
+{
+	u8 channel_num = 0;
+
+	switch (offset) {
+	case AMS_VCC_PSPLL0:
+		channel_num = AMS_VCC_PSPLL0_CH;
+		break;
+	case AMS_VCC_PSPLL3:
+		channel_num = AMS_VCC_PSPLL3_CH;
+		break;
+	case AMS_VCCINT:
+		channel_num = AMS_VCCINT_CH;
+		break;
+	case AMS_VCCBRAM:
+		channel_num = AMS_VCCBRAM_CH;
+		break;
+	case AMS_VCCAUX:
+		channel_num = AMS_VCCAUX_CH;
+		break;
+	case AMS_PSDDRPLL:
+		channel_num = AMS_PSDDRPLL_CH;
+		break;
+	case AMS_PSINTFPDDR:
+		channel_num = AMS_PSINTFPDDR_CH;
+		break;
+	default:
+		break;
+	}
+
+	/* set single channel, sequencer off mode */
+	ams_ps_update_reg(ams, AMS_REG_CONFIG1, AMS_CONF1_SEQ_MASK,
+			AMS_CONF1_SEQ_SINGLE_CHANNEL);
+
+	/* write the channel number */
+	ams_ps_update_reg(ams, AMS_REG_CONFIG0, AMS_CONF0_CHANNEL_NUM_MASK,
+			channel_num);
+	mdelay(1);
+}
+
+static void ams_read_vcc_reg(struct ams *ams, unsigned int offset, u32 *data)
+{
+	ams_enable_single_channel(ams, offset);
+	ams_read_reg(ams, offset, data);
+	ams_enable_channel_sequence(ams);
+}
+
+static int ams_read_raw(struct iio_dev *indio_dev,
+			struct iio_chan_spec const *chan,
+			int *val, int *val2, long mask)
+{
+	struct ams *ams = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&ams->mutex);
+		if (chan->scan_index >= (PS_SEQ_MAX * 3))
+			ams_read_vcc_reg(ams, chan->address, val);
+		else if (chan->scan_index >= PS_SEQ_MAX)
+			ams->pl_bus->read(ams, chan->address, val);
+		else
+			ams_ps_read_reg(ams, chan->address, val);
+		mutex_unlock(&ams->mutex);
+
+		*val2 = 0;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_VOLTAGE:
+			switch (chan->address) {
+			case AMS_SUPPLY1:
+			case AMS_SUPPLY2:
+			case AMS_SUPPLY3:
+			case AMS_SUPPLY4:
+				*val = AMS_SUPPLY_SCALE_3VOLT;
+				break;
+			case AMS_SUPPLY5:
+			case AMS_SUPPLY6:
+				if (chan->scan_index < PS_SEQ_MAX)
+					*val = AMS_SUPPLY_SCALE_6VOLT;
+				else
+					*val = AMS_SUPPLY_SCALE_3VOLT;
+				break;
+			case AMS_SUPPLY7:
+			case AMS_SUPPLY8:
+				*val = AMS_SUPPLY_SCALE_6VOLT;
+				break;
+			case AMS_SUPPLY9:
+			case AMS_SUPPLY10:
+				if (chan->scan_index < PS_SEQ_MAX)
+					*val = AMS_SUPPLY_SCALE_3VOLT;
+				else
+					*val = AMS_SUPPLY_SCALE_6VOLT;
+				break;
+			case AMS_VREFP:
+			case AMS_VREFN:
+					*val = AMS_SUPPLY_SCALE_3VOLT;
+				break;
+
+			default:
+				if (chan->scan_index >= (PS_SEQ_MAX * 3))
+					*val = AMS_SUPPLY_SCALE_3VOLT;
+				else
+					*val = AMS_SUPPLY_SCALE_1VOLT;
+				break;
+			}
+			*val2 = AMS_SUPPLY_SCALE_DIV_BIT;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		case IIO_TEMP:
+			*val = AMS_TEMP_SCALE;
+			*val2 = AMS_TEMP_SCALE_DIV_BIT;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_OFFSET:
+		/* Only the temperature channel has an offset */
+		*val = AMS_TEMP_OFFSET;
+		*val2 = 0;
+		return IIO_VAL_INT;
+	}
+
+	return -EINVAL;
+}
+
+static int ams_get_alarm_offset(int scan_index, enum iio_event_direction dir)
+{
+	int offset = 0;
+
+	if (scan_index >= PS_SEQ_MAX)
+		scan_index -= PS_SEQ_MAX;
+
+	if (dir == IIO_EV_DIR_FALLING) {
+		if (scan_index < AMS_SEQ_SUPPLY7)
+			offset = AMS_ALARM_THRESOLD_OFF_10;
+		else
+			offset = AMS_ALARM_THRESOLD_OFF_20;
+	}
+
+	switch (scan_index) {
+	case AMS_SEQ_TEMP:
+		return (AMS_ALARM_TEMP + offset);
+	case AMS_SEQ_SUPPLY1:
+		return (AMS_ALARM_SUPPLY1 + offset);
+	case AMS_SEQ_SUPPLY2:
+		return (AMS_ALARM_SUPPLY2 + offset);
+	case AMS_SEQ_SUPPLY3:
+		return (AMS_ALARM_SUPPLY3 + offset);
+	case AMS_SEQ_SUPPLY4:
+		return (AMS_ALARM_SUPPLY4 + offset);
+	case AMS_SEQ_SUPPLY5:
+		return (AMS_ALARM_SUPPLY5 + offset);
+	case AMS_SEQ_SUPPLY6:
+		return (AMS_ALARM_SUPPLY6 + offset);
+	case AMS_SEQ_SUPPLY7:
+		return (AMS_ALARM_SUPPLY7 + offset);
+	case AMS_SEQ_SUPPLY8:
+		return (AMS_ALARM_SUPPLY8 + offset);
+	case AMS_SEQ_SUPPLY9:
+		return (AMS_ALARM_SUPPLY9 + offset);
+	case AMS_SEQ_SUPPLY10:
+		return (AMS_ALARM_SUPPLY10 + offset);
+	case AMS_SEQ_VCCAMS:
+		return (AMS_ALARM_VCCAMS + offset);
+	case AMS_SEQ_TEMP_REMOTE:
+		return (AMS_ALARM_TEMP_REMOTE + offset);
+	}
+
+	return 0;
+}
+
+static const struct iio_chan_spec *ams_event_to_channel(
+		struct iio_dev *indio_dev, u32 event)
+{
+	int scan_index = 0, i;
+
+	if (event >= AMS_PL_ALARM_START) {
+		event -= AMS_PL_ALARM_START;
+		scan_index = PS_SEQ_MAX;
+	}
+
+	switch (event) {
+	case AMS_ALARM_BIT_TEMP:
+		scan_index += AMS_SEQ_TEMP;
+		break;
+	case AMS_ALARM_BIT_SUPPLY1:
+		scan_index += AMS_SEQ_SUPPLY1;
+		break;
+	case AMS_ALARM_BIT_SUPPLY2:
+		scan_index += AMS_SEQ_SUPPLY2;
+		break;
+	case AMS_ALARM_BIT_SUPPLY3:
+		scan_index += AMS_SEQ_SUPPLY3;
+		break;
+	case AMS_ALARM_BIT_SUPPLY4:
+		scan_index += AMS_SEQ_SUPPLY4;
+		break;
+	case AMS_ALARM_BIT_SUPPLY5:
+		scan_index += AMS_SEQ_SUPPLY5;
+		break;
+	case AMS_ALARM_BIT_SUPPLY6:
+		scan_index += AMS_SEQ_SUPPLY6;
+		break;
+	case AMS_ALARM_BIT_SUPPLY7:
+		scan_index += AMS_SEQ_SUPPLY7;
+		break;
+	case AMS_ALARM_BIT_SUPPLY8:
+		scan_index += AMS_SEQ_SUPPLY8;
+		break;
+	case AMS_ALARM_BIT_SUPPLY9:
+		scan_index += AMS_SEQ_SUPPLY9;
+		break;
+	case AMS_ALARM_BIT_SUPPLY10:
+		scan_index += AMS_SEQ_SUPPLY10;
+		break;
+	case AMS_ALARM_BIT_VCCAMS:
+		scan_index += AMS_SEQ_VCCAMS;
+		break;
+	case AMS_ALARM_BIT_TEMP_REMOTE:
+		scan_index += AMS_SEQ_TEMP_REMOTE;
+		break;
+	}
+
+	for (i = 0; i < indio_dev->num_channels; i++)
+		if (indio_dev->channels[i].scan_index == scan_index)
+			break;
+
+	return &indio_dev->channels[i];
+}
+
+static int ams_get_alarm_mask(int scan_index)
+{
+	int bit = 0;
+
+	if (scan_index >= PS_SEQ_MAX) {
+		bit = AMS_PL_ALARM_START;
+		scan_index -= PS_SEQ_MAX;
+	}
+
+	switch (scan_index) {
+	case AMS_SEQ_TEMP:
+		return BIT(AMS_ALARM_BIT_TEMP + bit);
+	case AMS_SEQ_SUPPLY1:
+		return BIT(AMS_ALARM_BIT_SUPPLY1 + bit);
+	case AMS_SEQ_SUPPLY2:
+		return BIT(AMS_ALARM_BIT_SUPPLY2 + bit);
+	case AMS_SEQ_SUPPLY3:
+		return BIT(AMS_ALARM_BIT_SUPPLY3 + bit);
+	case AMS_SEQ_SUPPLY4:
+		return BIT(AMS_ALARM_BIT_SUPPLY4 + bit);
+	case AMS_SEQ_SUPPLY5:
+		return BIT(AMS_ALARM_BIT_SUPPLY5 + bit);
+	case AMS_SEQ_SUPPLY6:
+		return BIT(AMS_ALARM_BIT_SUPPLY6 + bit);
+	case AMS_SEQ_SUPPLY7:
+		return BIT(AMS_ALARM_BIT_SUPPLY7 + bit);
+	case AMS_SEQ_SUPPLY8:
+		return BIT(AMS_ALARM_BIT_SUPPLY8 + bit);
+	case AMS_SEQ_SUPPLY9:
+		return BIT(AMS_ALARM_BIT_SUPPLY9 + bit);
+	case AMS_SEQ_SUPPLY10:
+		return BIT(AMS_ALARM_BIT_SUPPLY10 + bit);
+	case AMS_SEQ_VCCAMS:
+		return BIT(AMS_ALARM_BIT_VCCAMS + bit);
+	case AMS_SEQ_TEMP_REMOTE:
+		return BIT(AMS_ALARM_BIT_TEMP_REMOTE + bit);
+	}
+
+	return 0;
+}
+
+static int ams_read_event_config(struct iio_dev *indio_dev,
+				 const struct iio_chan_spec *chan,
+				 enum iio_event_type type,
+				 enum iio_event_direction dir)
+{
+	struct ams *ams = iio_priv(indio_dev);
+
+	return (ams->alarm_mask & ams_get_alarm_mask(chan->scan_index)) ? 1 : 0;
+}
+
+static int ams_write_event_config(struct iio_dev *indio_dev,
+				  const struct iio_chan_spec *chan,
+				  enum iio_event_type type,
+				  enum iio_event_direction dir,
+				  int state)
+{
+	struct ams *ams = iio_priv(indio_dev);
+	unsigned int alarm;
+
+	alarm = ams_get_alarm_mask(chan->scan_index);
+
+	mutex_lock(&ams->mutex);
+
+	if (state)
+		ams->alarm_mask |= alarm;
+	else
+		ams->alarm_mask &= ~alarm;
+
+	iio_ams_update_alarm(ams, ams->alarm_mask);
+
+	mutex_unlock(&ams->mutex);
+
+	return 0;
+}
+
+static int ams_read_event_value(struct iio_dev *indio_dev,
+				const struct iio_chan_spec *chan,
+				enum iio_event_type type,
+				enum iio_event_direction dir,
+				enum iio_event_info info, int *val, int *val2)
+{
+	struct ams *ams = iio_priv(indio_dev);
+	unsigned int offset = ams_get_alarm_offset(chan->scan_index, dir);
+
+	mutex_lock(&ams->mutex);
+
+	if (chan->scan_index >= PS_SEQ_MAX)
+		ams->pl_bus->read(ams, offset, val);
+	else
+		ams_ps_read_reg(ams, offset, val);
+
+	mutex_unlock(&ams->mutex);
+
+	*val2 = 0;
+	return IIO_VAL_INT;
+}
+
+static int ams_write_event_value(struct iio_dev *indio_dev,
+				 const struct iio_chan_spec *chan,
+				 enum iio_event_type type,
+				 enum iio_event_direction dir,
+				 enum iio_event_info info, int val, int val2)
+{
+	struct ams *ams = iio_priv(indio_dev);
+	unsigned int offset;
+
+	mutex_lock(&ams->mutex);
+
+	/* Set temperature channel threshold to direct threshold */
+	if (chan->type == IIO_TEMP) {
+		offset = ams_get_alarm_offset(chan->scan_index,
+					      IIO_EV_DIR_FALLING);
+
+		if (chan->scan_index >= PS_SEQ_MAX)
+			ams->pl_bus->update(ams, offset,
+					    AMS_ALARM_THR_DIRECT_MASK,
+					    AMS_ALARM_THR_DIRECT_MASK);
+		else
+			ams_ps_update_reg(ams, offset,
+					  AMS_ALARM_THR_DIRECT_MASK,
+					  AMS_ALARM_THR_DIRECT_MASK);
+	}
+
+	offset = ams_get_alarm_offset(chan->scan_index, dir);
+	if (chan->scan_index >= PS_SEQ_MAX)
+		ams->pl_bus->write(ams, offset, val);
+	else
+		ams_ps_write_reg(ams, offset, val);
+
+	mutex_unlock(&ams->mutex);
+
+	return 0;
+}
+
+static void ams_handle_event(struct iio_dev *indio_dev, u32 event)
+{
+	const struct iio_chan_spec *chan;
+
+	chan = ams_event_to_channel(indio_dev, event);
+
+	if (chan->type == IIO_TEMP) {
+		/* The temperature channel only supports over-temperature
+		 * events
+		 */
+		iio_push_event(indio_dev,
+			       IIO_UNMOD_EVENT_CODE(chan->type, chan->channel,
+						    IIO_EV_TYPE_THRESH,
+						    IIO_EV_DIR_RISING),
+			iio_get_time_ns(indio_dev));
+	} else {
+		/* For other channels we don't know whether it is a upper or
+		 * lower threshold event. Userspace will have to check the
+		 * channel value if it wants to know.
+		 */
+		iio_push_event(indio_dev,
+			       IIO_UNMOD_EVENT_CODE(chan->type, chan->channel,
+						    IIO_EV_TYPE_THRESH,
+						    IIO_EV_DIR_EITHER),
+			iio_get_time_ns(indio_dev));
+	}
+}
+
+static void ams_handle_events(struct iio_dev *indio_dev, unsigned long events)
+{
+	unsigned int bit;
+
+	for_each_set_bit(bit, &events, AMS_NO_OF_ALARMS)
+		ams_handle_event(indio_dev, bit);
+}
+
+/**
+ * ams_unmask_worker - ams alarm interrupt unmask worker
+ * @work :		work to be done
+ *
+ * The ZynqMP threshold interrupts are level sensitive. Since we can't make the
+ * threshold condition go way from within the interrupt handler, this means as
+ * soon as a threshold condition is present we would enter the interrupt handler
+ * again and again. To work around this we mask all active thresholds interrupts
+ * in the interrupt handler and start a timer. In this timer we poll the
+ * interrupt status and only if the interrupt is inactive we unmask it again.
+ */
+static void ams_unmask_worker(struct work_struct *work)
+{
+	struct ams *ams = container_of(work, struct ams, ams_unmask_work.work);
+	unsigned int status, unmask;
+
+	spin_lock_irq(&ams->lock);
+
+	ams_read_reg(ams, AMS_ISR_0, &status);
+
+	/* Clear those bits which are not active anymore */
+	unmask = (ams->masked_alarm ^ status) & ams->masked_alarm;
+
+	/* clear status of disabled alarm */
+	unmask |= ams->intr_mask;
+
+	ams->masked_alarm &= status;
+
+	/* Also clear those which are masked out anyway */
+	ams->masked_alarm &= ~ams->intr_mask;
+
+	/* Clear the interrupts before we unmask them */
+	ams_write_reg(ams, AMS_ISR_0, unmask);
+
+	ams_update_intrmask(ams, 0, 0);
+
+	spin_unlock_irq(&ams->lock);
+
+	/* if still pending some alarm re-trigger the timer */
+	if (ams->masked_alarm)
+		schedule_delayed_work(&ams->ams_unmask_work,
+				      msecs_to_jiffies(AMS_UNMASK_TIMEOUT));
+}
+
+static irqreturn_t ams_iio_irq(int irq, void *data)
+{
+	unsigned int isr0, isr1;
+	struct iio_dev *indio_dev = data;
+	struct ams *ams = iio_priv(indio_dev);
+
+	spin_lock(&ams->lock);
+
+	ams_read_reg(ams, AMS_ISR_0, &isr0);
+	ams_read_reg(ams, AMS_ISR_1, &isr1);
+
+	/* only process alarm that are not masked */
+	isr0 &= ~((ams->intr_mask & AMS_ISR0_ALARM_MASK) | ams->masked_alarm);
+	isr1 &= ~(ams->intr_mask >> AMS_ISR1_INTR_MASK_SHIFT);
+
+	/* clear interrupt */
+	ams_write_reg(ams, AMS_ISR_0, isr0);
+	ams_write_reg(ams, AMS_ISR_1, isr1);
+
+	if (isr0) {
+		/* Once the alarm interrupt occurred, mask until get cleared */
+		ams->masked_alarm |= isr0;
+		ams_update_intrmask(ams, 0, 0);
+
+		ams_handle_events(indio_dev, isr0);
+
+		schedule_delayed_work(&ams->ams_unmask_work,
+				      msecs_to_jiffies(AMS_UNMASK_TIMEOUT));
+	}
+
+	spin_unlock(&ams->lock);
+
+	return IRQ_HANDLED;
+}
+
+static const struct iio_event_spec ams_temp_events[] = {
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_RISING,
+		.mask_separate = BIT(IIO_EV_INFO_ENABLE) |
+				BIT(IIO_EV_INFO_VALUE),
+	},
+};
+
+static const struct iio_event_spec ams_voltage_events[] = {
+	{
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_RISING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE),
+	}, {
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_FALLING,
+		.mask_separate = BIT(IIO_EV_INFO_VALUE),
+	}, {
+		.type = IIO_EV_TYPE_THRESH,
+		.dir = IIO_EV_DIR_EITHER,
+		.mask_separate = BIT(IIO_EV_INFO_ENABLE),
+	},
+};
+
+static const struct iio_chan_spec ams_ps_channels[] = {
+	AMS_PS_CHAN_TEMP(AMS_SEQ_TEMP, AMS_TEMP, "ps_temp"),
+	AMS_PS_CHAN_TEMP(AMS_SEQ_TEMP_REMOTE, AMS_TEMP_REMOTE, "remote_temp"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY1, AMS_SUPPLY1, "vccpsintlp"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY2, AMS_SUPPLY2, "vccpsintfp"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY3, AMS_SUPPLY3, "vccpsaux"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY4, AMS_SUPPLY4, "vccpsddr"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY5, AMS_SUPPLY5, "vccpsio3"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY6, AMS_SUPPLY6, "vccpsio0"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY7, AMS_SUPPLY7, "vccpsio1"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY8, AMS_SUPPLY8, "vccpsio2"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY9, AMS_SUPPLY9, "psmgtravcc"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_SUPPLY10, AMS_SUPPLY10, "psmgtravtt"),
+	AMS_PS_CHAN_VOLTAGE(AMS_SEQ_VCCAMS, AMS_VCCAMS, "vccams"),
+};
+
+static const struct iio_chan_spec ams_pl_channels[] = {
+	AMS_PL_CHAN_TEMP(AMS_SEQ_TEMP, AMS_TEMP, "pl_temp"),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY1, AMS_SUPPLY1, "vccint", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY2, AMS_SUPPLY2, "vccaux", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_VREFP, AMS_VREFP, "vccvrefp", false),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_VREFN, AMS_VREFN, "vccvrefn", false),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY3, AMS_SUPPLY3, "vccbram", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY4, AMS_SUPPLY4, "vccplintlp", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY5, AMS_SUPPLY5, "vccplintfp", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY6, AMS_SUPPLY6, "vccplaux", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_VCCAMS, AMS_VCCAMS, "vccams", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_VP_VN, AMS_VP_VN, "vccvpvn", false),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY7, AMS_SUPPLY7, "vuser0", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY8, AMS_SUPPLY8, "vuser1", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY9, AMS_SUPPLY9, "vuser2", true),
+	AMS_PL_CHAN_VOLTAGE(AMS_SEQ_SUPPLY10, AMS_SUPPLY10, "vuser3", true),
+	AMS_PL_AUX_CHAN_VOLTAGE(0, "vccaux0"),
+	AMS_PL_AUX_CHAN_VOLTAGE(1, "vccaux1"),
+	AMS_PL_AUX_CHAN_VOLTAGE(2, "vccaux2"),
+	AMS_PL_AUX_CHAN_VOLTAGE(3, "vccaux3"),
+	AMS_PL_AUX_CHAN_VOLTAGE(4, "vccaux4"),
+	AMS_PL_AUX_CHAN_VOLTAGE(5, "vccaux5"),
+	AMS_PL_AUX_CHAN_VOLTAGE(6, "vccaux6"),
+	AMS_PL_AUX_CHAN_VOLTAGE(7, "vccaux7"),
+	AMS_PL_AUX_CHAN_VOLTAGE(8, "vccaux8"),
+	AMS_PL_AUX_CHAN_VOLTAGE(9, "vccaux9"),
+	AMS_PL_AUX_CHAN_VOLTAGE(10, "vccaux10"),
+	AMS_PL_AUX_CHAN_VOLTAGE(11, "vccaux11"),
+	AMS_PL_AUX_CHAN_VOLTAGE(12, "vccaux12"),
+	AMS_PL_AUX_CHAN_VOLTAGE(13, "vccaux13"),
+	AMS_PL_AUX_CHAN_VOLTAGE(14, "vccaux14"),
+	AMS_PL_AUX_CHAN_VOLTAGE(15, "vccaux15"),
+};
+
+static const struct iio_chan_spec ams_ctrl_channels[] = {
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_VCC_PSPLL, AMS_VCC_PSPLL0, "vcc_pspll0"),
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_VCC_PSBATT, AMS_VCC_PSPLL3, "vcc_psbatt"),
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_VCCINT, AMS_VCCINT, "vccint"),
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_VCCBRAM, AMS_VCCBRAM, "vccbram"),
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_VCCAUX, AMS_VCCAUX, "vccaux"),
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_PSDDRPLL, AMS_PSDDRPLL, "vcc_psddrpll"),
+	AMS_CTRL_CHAN_VOLTAGE(AMS_SEQ_INTDDR, AMS_PSINTFPDDR, "vccpsintfpddr"),
+};
+
+static int ams_init_module(struct iio_dev *indio_dev, struct device_node *np,
+			   struct iio_chan_spec *channels)
+{
+	struct ams *ams = iio_priv(indio_dev);
+	struct device_node *chan_node, *child;
+	int ret, num_channels = 0;
+	unsigned int reg;
+
+	if (of_device_is_compatible(np, "xlnx,zynqmp-ams-ps")) {
+		ams->ps_base = of_iomap(np, 0);
+		if (!ams->ps_base)
+			return -ENXIO;
+
+		/* add PS channels to iio device channels */
+		memcpy(channels + num_channels, ams_ps_channels,
+		       sizeof(ams_ps_channels));
+		num_channels += ARRAY_SIZE(ams_ps_channels);
+	} else if (of_device_is_compatible(np, "xlnx,zynqmp-ams-pl")) {
+		ams->pl_base = of_iomap(np, 0);
+		if (!ams->pl_base)
+			return -ENXIO;
+
+		/* Copy only first 10 fix channels */
+		memcpy(channels + num_channels, ams_pl_channels,
+		       AMS_PL_MAX_FIXED_CHANNEL * sizeof(*channels));
+		num_channels += AMS_PL_MAX_FIXED_CHANNEL;
+
+		chan_node = of_get_child_by_name(np, "xlnx,ext-channels");
+		if (chan_node) {
+			for_each_child_of_node(chan_node, child) {
+				ret = of_property_read_u32(child, "reg", &reg);
+				if (ret || reg > AMS_PL_MAX_EXT_CHANNEL)
+					continue;
+
+				memcpy(&channels[num_channels],
+				       &ams_pl_channels[reg +
+				       AMS_PL_MAX_FIXED_CHANNEL],
+				       sizeof(*channels));
+
+				if (of_property_read_bool(child,
+							  "xlnx,bipolar"))
+					channels[num_channels].
+						scan_type.sign = 's';
+
+				num_channels += 1;
+			}
+		}
+		of_node_put(chan_node);
+	} else if (of_device_is_compatible(np, "xlnx,zynqmp-ams")) {
+		/* add AMS channels to iio device channels */
+		memcpy(channels + num_channels, ams_ctrl_channels,
+				sizeof(ams_ctrl_channels));
+		num_channels += ARRAY_SIZE(ams_ctrl_channels);
+	} else {
+		return -EINVAL;
+	}
+
+	return num_channels;
+}
+
+static int ams_parse_dt(struct iio_dev *indio_dev, struct platform_device *pdev)
+{
+	struct ams *ams = iio_priv(indio_dev);
+	struct iio_chan_spec *ams_channels, *dev_channels;
+	struct device_node *child_node = NULL, *np = pdev->dev.of_node;
+	int ret, chan_vol = 0, chan_temp = 0, i, rising_off, falling_off;
+	unsigned int num_channels = 0;
+
+	/* Initialize buffer for channel specification */
+	ams_channels = kzalloc(sizeof(ams_ps_channels) +
+			       sizeof(ams_pl_channels) +
+			       sizeof(ams_ctrl_channels), GFP_KERNEL);
+	if (!ams_channels)
+		return -ENOMEM;
+
+	if (of_device_is_available(np)) {
+		ret = ams_init_module(indio_dev, np, ams_channels);
+		if (ret < 0) {
+			kfree(ams_channels);
+			return ret;
+		}
+
+		num_channels += ret;
+	}
+
+	for_each_child_of_node(np, child_node) {
+		if (of_device_is_available(child_node)) {
+			ret = ams_init_module(indio_dev, child_node,
+					      ams_channels + num_channels);
+			if (ret < 0) {
+				kfree(ams_channels);
+				return ret;
+			}
+
+			num_channels += ret;
+		}
+	}
+
+	for (i = 0; i < num_channels; i++) {
+		if (ams_channels[i].type == IIO_VOLTAGE)
+			ams_channels[i].channel = chan_vol++;
+		else
+			ams_channels[i].channel = chan_temp++;
+
+		if (ams_channels[i].scan_index < (PS_SEQ_MAX * 3)) {
+			/* set threshold to max and min for each channel */
+			falling_off = ams_get_alarm_offset(
+					ams_channels[i].scan_index,
+					IIO_EV_DIR_FALLING);
+			rising_off = ams_get_alarm_offset(
+					ams_channels[i].scan_index,
+					IIO_EV_DIR_RISING);
+			if (ams_channels[i].scan_index >= PS_SEQ_MAX) {
+				ams->pl_bus->write(ams, falling_off,
+						AMS_ALARM_THR_MIN);
+				ams->pl_bus->write(ams, rising_off,
+						AMS_ALARM_THR_MAX);
+			} else {
+				ams_ps_write_reg(ams, falling_off,
+						AMS_ALARM_THR_MIN);
+				ams_ps_write_reg(ams, rising_off,
+						AMS_ALARM_THR_MAX);
+			}
+		}
+	}
+
+	dev_channels = devm_kzalloc(&pdev->dev, sizeof(*dev_channels) *
+				    num_channels, GFP_KERNEL);
+	if (!dev_channels) {
+		kfree(ams_channels);
+		return -ENOMEM;
+	}
+
+	memcpy(dev_channels, ams_channels,
+	       sizeof(*ams_channels) * num_channels);
+	kfree(ams_channels);
+	indio_dev->channels = dev_channels;
+	indio_dev->num_channels = num_channels;
+
+	return 0;
+}
+
+static const struct iio_info iio_pl_info = {
+	.read_raw = &ams_read_raw,
+	.read_event_config = &ams_read_event_config,
+	.write_event_config = &ams_write_event_config,
+	.read_event_value = &ams_read_event_value,
+	.write_event_value = &ams_write_event_value,
+};
+
+static const struct ams_pl_bus_ops ams_pl_apb = {
+	.read = ams_apb_pl_read_reg,
+	.write = ams_apb_pl_write_reg,
+	.update = ams_apb_pl_update_reg,
+};
+
+static const struct of_device_id ams_of_match_table[] = {
+	{ .compatible = "xlnx,zynqmp-ams", &ams_pl_apb },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ams_of_match_table);
+
+static int ams_probe(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev;
+	struct ams *ams;
+	struct resource *res;
+	const struct of_device_id *id;
+	int ret;
+
+	if (!pdev->dev.of_node)
+		return -ENODEV;
+
+	id = of_match_node(ams_of_match_table, pdev->dev.of_node);
+	if (!id)
+		return -ENODEV;
+
+	indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*ams));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	ams = iio_priv(indio_dev);
+	ams->indio_dev = indio_dev;
+	ams->pl_bus = id->data;
+	mutex_init(&ams->mutex);
+	spin_lock_init(&ams->lock);
+
+	indio_dev->dev.parent = &pdev->dev;
+	indio_dev->dev.of_node = pdev->dev.of_node;
+	indio_dev->name = "ams";
+
+	indio_dev->info = &iio_pl_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ams-base");
+	ams->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ams->base))
+		return PTR_ERR(ams->base);
+
+	INIT_DELAYED_WORK(&ams->ams_unmask_work, ams_unmask_worker);
+
+	ams->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(ams->clk))
+		return PTR_ERR(ams->clk);
+	clk_prepare_enable(ams->clk);
+
+	ret = iio_ams_init_device(ams);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to initialize AMS\n");
+		goto clk_disable;
+	}
+
+	ret = ams_parse_dt(indio_dev, pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "failure in parsing DT\n");
+		goto clk_disable;
+	}
+
+	ams_enable_channel_sequence(ams);
+
+	ams->irq = platform_get_irq_byname(pdev, "ams-irq");
+	ret = devm_request_irq(&pdev->dev, ams->irq, &ams_iio_irq, 0, "ams-irq",
+			       indio_dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register interrupt\n");
+		goto clk_disable;
+	}
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	return iio_device_register(indio_dev);
+
+clk_disable:
+	clk_disable_unprepare(ams->clk);
+	return ret;
+}
+
+static int ams_remove(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct ams *ams = iio_priv(indio_dev);
+
+	cancel_delayed_work(&ams->ams_unmask_work);
+
+	/* Unregister the device */
+	iio_device_unregister(indio_dev);
+	clk_disable_unprepare(ams->clk);
+	return 0;
+}
+
+static int __maybe_unused ams_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ams *ams = iio_priv(indio_dev);
+
+	clk_disable_unprepare(ams->clk);
+
+	return 0;
+}
+
+static int __maybe_unused ams_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ams *ams = iio_priv(indio_dev);
+
+	clk_prepare_enable(ams->clk);
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(ams_pm_ops, ams_suspend, ams_resume);
+
+static struct platform_driver ams_driver = {
+	.probe = ams_probe,
+	.remove = ams_remove,
+	.driver = {
+		.name = "ams",
+		.pm	= &ams_pm_ops,
+		.of_match_table = ams_of_match_table,
+	},
+};
+module_platform_driver(ams_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/xilinx-ams.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/xilinx-ams.h
@@ -0,0 +1,281 @@
+#ifndef __XILINX_AMS_H__
+#define __XILINX_AMS_H__
+
+#define AMS_MISC_CTRL     0x000
+#define AMS_ISR_0         0x010
+#define AMS_ISR_1         0x014
+#define AMS_IMR_0         0x018
+#define AMS_IMR_1         0x01c
+#define AMS_IER_0         0x020
+#define AMS_IER_1         0x024
+#define AMS_IDR_0         0x028
+#define AMS_IDR_1         0x02c
+#define AMS_PS_CSTS       0x040
+#define AMS_PL_CSTS       0x044
+#define AMS_MON_CSTS      0x050
+
+#define AMS_VCC_PSPLL0    0x060
+#define AMS_VCC_PSPLL3    0x06C
+#define AMS_VCCINT        0x078
+#define AMS_VCCBRAM       0x07C
+#define AMS_VCCAUX        0x080
+#define AMS_PSDDRPLL      0x084
+#define AMS_PSINTFPDDR    0x09C
+
+#define AMS_VCC_PSPLL0_CH 48
+#define AMS_VCC_PSPLL3_CH 51
+#define AMS_VCCINT_CH     54
+#define AMS_VCCBRAM_CH    55
+#define AMS_VCCAUX_CH     56
+#define AMS_PSDDRPLL_CH   57
+#define AMS_PSINTFPDDR_CH 63
+
+#define AMS_REG_CONFIG0   0x100
+#define AMS_REG_CONFIG1   0x104
+#define AMS_REG_CONFIG2   0x108
+#define AMS_REG_CONFIG3   0x10C
+#define AMS_REG_CONFIG4   0x110
+#define AMS_REG_SEQ_CH0   0x120
+#define AMS_REG_SEQ_CH1   0x124
+#define AMS_REG_SEQ_CH2   0x118
+
+#define AMS_TEMP          0x000
+#define AMS_SUPPLY1       0x004
+#define AMS_SUPPLY2       0x008
+#define AMS_VP_VN         0x00c
+#define AMS_VREFP         0x010
+#define AMS_VREFN         0x014
+#define AMS_SUPPLY3       0x018
+#define AMS_SUPPLY4       0x034
+#define AMS_SUPPLY5       0x038
+#define AMS_SUPPLY6       0x03c
+#define AMS_SUPPLY7       0x200
+#define AMS_SUPPLY8       0x204
+#define AMS_SUPPLY9       0x208
+#define AMS_SUPPLY10      0x20c
+#define AMS_VCCAMS        0x210
+#define AMS_TEMP_REMOTE   0x214
+
+#define AMS_REG_VAUX(x)   (0x40 + (4*(x)))
+#define AMS_REG_VUSER(x)  (0x200 + (4*(x)))
+
+#define AMS_PS_RESET_VALUE   0xFFFFU
+#define AMS_PL_RESET_VALUE   0xFFFFU
+
+#define AMS_CONF0_CHANNEL_NUM_MASK      (0x3f << 0)
+
+#define AMS_CONF1_SEQ_MASK              (0xf << 12)
+#define AMS_CONF1_SEQ_DEFAULT           (0 << 12)
+#define AMS_CONF1_SEQ_SINGLE_PASS       (1 << 12)
+#define AMS_CONF1_SEQ_CONTINUOUS        (2 << 12)
+#define AMS_CONF1_SEQ_SINGLE_CHANNEL    (3 << 12)
+
+#define AMS_REG_SEQ0_MASK        0xFFFF
+#define AMS_REG_SEQ2_MASK        0x3F
+#define AMS_REG_SEQ1_MASK        0xFFFF
+#define AMS_REG_SEQ2_MASK_SHIFT  16
+#define AMS_REG_SEQ1_MASK_SHIFT  22
+
+#define AMS_REGCFG1_ALARM_MASK   0xF0F
+#define AMS_REGCFG3_ALARM_MASK   0x3F
+
+#define AMS_ALARM_TEMP            0x140
+#define AMS_ALARM_SUPPLY1         0x144
+#define AMS_ALARM_SUPPLY2         0x148
+#define AMS_ALARM_OT              0x14c
+
+#define AMS_ALARM_SUPPLY3         0x160
+#define AMS_ALARM_SUPPLY4         0x164
+#define AMS_ALARM_SUPPLY5         0x168
+#define AMS_ALARM_SUPPLY6         0x16c
+#define AMS_ALARM_SUPPLY7         0x180
+#define AMS_ALARM_SUPPLY8         0x184
+#define AMS_ALARM_SUPPLY9         0x188
+#define AMS_ALARM_SUPPLY10        0x18c
+#define AMS_ALARM_VCCAMS          0x190
+#define AMS_ALARM_TEMP_REMOTE     0x194
+#define AMS_ALARM_THRESOLD_OFF_10 0x10
+#define AMS_ALARM_THRESOLD_OFF_20 0x20
+
+#define AMS_ALARM_THR_DIRECT_MASK 0x01
+#define AMS_ALARM_THR_MIN         0x0000
+#define AMS_ALARM_THR_MAX         0xffff
+
+#define AMS_NO_OF_ALARMS             32
+#define AMS_PL_ALARM_START           16
+#define AMS_ISR0_ALARM_MASK          0xFFFFFFFFU
+#define AMS_ISR1_ALARM_MASK          0xE000001FU
+#define AMS_ISR1_INTR_MASK_SHIFT     32
+#define AMS_ISR0_ALARM_2_TO_0_MASK     0x07
+#define AMS_ISR0_ALARM_6_TO_3_MASK     0x78
+#define AMS_ISR0_ALARM_12_TO_7_MASK    0x3F
+#define AMS_CONF1_ALARM_2_TO_0_SHIFT   1
+#define AMS_CONF1_ALARM_6_TO_3_SHIFT   5
+#define AMS_CONF3_ALARM_12_TO_7_SHIFT  8
+
+#define AMS_PS_CSTS_PS_READY       0x08010000U
+#define AMS_PL_CSTS_ACCESS_MASK    0x00000001U
+
+#define AMS_PL_MAX_FIXED_CHANNEL   10
+#define AMS_PL_MAX_EXT_CHANNEL     20
+
+#define AMS_INIT_TIMEOUT	10000
+
+/* Following scale and offset value is derivef from
+ * UG580 (v1.7) December 20, 2016
+ */
+#define AMS_SUPPLY_SCALE_1VOLT     1000
+#define AMS_SUPPLY_SCALE_3VOLT     3000
+#define AMS_SUPPLY_SCALE_6VOLT     6000
+#define AMS_SUPPLY_SCALE_DIV_BIT   16
+
+#define AMS_TEMP_SCALE             509314
+#define AMS_TEMP_SCALE_DIV_BIT     16
+#define AMS_TEMP_OFFSET            -((280230L << 16) / 509314)
+
+enum ams_alarm_bit {
+	AMS_ALARM_BIT_TEMP,
+	AMS_ALARM_BIT_SUPPLY1,
+	AMS_ALARM_BIT_SUPPLY2,
+	AMS_ALARM_BIT_SUPPLY3,
+	AMS_ALARM_BIT_SUPPLY4,
+	AMS_ALARM_BIT_SUPPLY5,
+	AMS_ALARM_BIT_SUPPLY6,
+	AMS_ALARM_BIT_RESERVED,
+	AMS_ALARM_BIT_SUPPLY7,
+	AMS_ALARM_BIT_SUPPLY8,
+	AMS_ALARM_BIT_SUPPLY9,
+	AMS_ALARM_BIT_SUPPLY10,
+	AMS_ALARM_BIT_VCCAMS,
+	AMS_ALARM_BIT_TEMP_REMOTE
+};
+
+enum ams_seq {
+	AMS_SEQ_VCC_PSPLL,
+	AMS_SEQ_VCC_PSBATT,
+	AMS_SEQ_VCCINT,
+	AMS_SEQ_VCCBRAM,
+	AMS_SEQ_VCCAUX,
+	AMS_SEQ_PSDDRPLL,
+	AMS_SEQ_INTDDR
+};
+
+enum ams_ps_pl_seq {
+	AMS_SEQ_CALIB,
+	AMS_SEQ_RSVD_1,
+	AMS_SEQ_RSVD_2,
+	AMS_SEQ_TEST,
+	AMS_SEQ_RSVD_4,
+	AMS_SEQ_SUPPLY4,
+	AMS_SEQ_SUPPLY5,
+	AMS_SEQ_SUPPLY6,
+	AMS_SEQ_TEMP,
+	AMS_SEQ_SUPPLY2,
+	AMS_SEQ_SUPPLY1,
+	AMS_SEQ_VP_VN,
+	AMS_SEQ_VREFP,
+	AMS_SEQ_VREFN,
+	AMS_SEQ_SUPPLY3,
+	AMS_SEQ_CURRENT_MON,
+	AMS_SEQ_SUPPLY7,
+	AMS_SEQ_SUPPLY8,
+	AMS_SEQ_SUPPLY9,
+	AMS_SEQ_SUPPLY10,
+	AMS_SEQ_VCCAMS,
+	AMS_SEQ_TEMP_REMOTE,
+	AMS_SEQ_MAX
+};
+
+#define AMS_SEQ(x)          (AMS_SEQ_MAX + (x))
+#define AMS_VAUX_SEQ(x)     (AMS_SEQ_MAX + (x))
+
+#define PS_SEQ_MAX          AMS_SEQ_MAX
+#define PS_SEQ(x)           (x)
+#define PL_SEQ(x)           (PS_SEQ_MAX + x)
+
+#define PL_SEQ_MAX	((AMS_SEQ_MAX * 2) + 16U) /* PS Slot + PL Slot + 16 VAUX Channels */
+
+#define AMS_CHAN_TEMP(_scan_index, _addr, _ext) { \
+	.type = IIO_TEMP, \
+	.indexed = 1, \
+	.address = (_addr), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+		BIT(IIO_CHAN_INFO_SCALE) | \
+		BIT(IIO_CHAN_INFO_OFFSET), \
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \
+	.event_spec = ams_temp_events, \
+	.num_event_specs = ARRAY_SIZE(ams_temp_events), \
+	.scan_index = (_scan_index), \
+	.scan_type = { \
+		.sign = 'u', \
+		.realbits = 12, \
+		.storagebits = 16, \
+		.shift = 4, \
+		.endianness = IIO_CPU, \
+	}, \
+	.extend_name = _ext, \
+}
+
+#define AMS_CHAN_VOLTAGE(_scan_index, _addr, _ext, _alarm) { \
+	.type = IIO_VOLTAGE, \
+	.indexed = 1, \
+	.address = (_addr), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+		BIT(IIO_CHAN_INFO_SCALE), \
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \
+	.event_spec = (_alarm) ? ams_voltage_events : NULL, \
+	.num_event_specs = (_alarm) ? ARRAY_SIZE(ams_voltage_events) : 0, \
+	.scan_index = (_scan_index), \
+	.scan_type = { \
+		.realbits = 10, \
+		.storagebits = 16, \
+		.shift = 6, \
+		.endianness = IIO_CPU, \
+	}, \
+	.extend_name = _ext, \
+}
+
+#define AMS_PS_CHAN_TEMP(_scan_index, _addr, _ext) \
+	AMS_CHAN_TEMP(PS_SEQ(_scan_index), _addr, _ext)
+#define AMS_PS_CHAN_VOLTAGE(_scan_index, _addr, _ext) \
+	AMS_CHAN_VOLTAGE(PS_SEQ(_scan_index), _addr, _ext, true)
+
+#define AMS_PL_CHAN_TEMP(_scan_index, _addr, _ext) \
+	AMS_CHAN_TEMP(PL_SEQ(_scan_index), _addr, _ext)
+#define AMS_PL_CHAN_VOLTAGE(_scan_index, _addr, _ext, _alarm) \
+	AMS_CHAN_VOLTAGE(PL_SEQ(_scan_index), _addr, _ext, _alarm)
+#define AMS_PL_AUX_CHAN_VOLTAGE(_auxno, _ext) \
+	AMS_CHAN_VOLTAGE(PL_SEQ(AMS_VAUX_SEQ(_auxno)), \
+			AMS_REG_VAUX(_auxno), _ext, false)
+#define AMS_CTRL_CHAN_VOLTAGE(_scan_index, _addr, _ext) \
+	AMS_CHAN_VOLTAGE(PL_SEQ(AMS_VAUX_SEQ(AMS_SEQ(_scan_index))), \
+			_addr, _ext, false)
+
+struct ams {
+	void __iomem *base;
+	void __iomem *ps_base;
+	void __iomem *pl_base;
+	struct clk *clk;
+	struct device *dev;
+
+	struct mutex mutex;
+	spinlock_t lock;
+
+	unsigned int alarm_mask;
+	unsigned int masked_alarm;
+	u64 intr_mask;
+	int irq;
+
+	struct delayed_work ams_unmask_work;
+	const struct ams_pl_bus_ops *pl_bus;
+	struct iio_dev *indio_dev;
+};
+
+struct ams_pl_bus_ops {
+	void (*read)(struct ams *ams, unsigned int offset, unsigned int *data);
+	void (*write)(struct ams *ams, unsigned int offset, unsigned int data);
+	void (*update)(struct ams *ams, unsigned int offset, u32 mask,
+			u32 data);
+};
+
+#endif /* __XILINX_AMS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/xilinx-xadc-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/xilinx-xadc-core.c
@@ -454,6 +454,9 @@
 	.interrupt_handler = xadc_zynq_interrupt_handler,
 	.update_alarm = xadc_zynq_update_alarm,
 	.type = XADC_TYPE_S7,
+	/* Temp in C = (val * 503.975) / 2**bits - 273.15 */
+	.temp_scale = 503975,
+	.temp_offset = 273150,
 };
 
 static const unsigned int xadc_axi_reg_offsets[] = {
@@ -564,6 +567,9 @@
 	.interrupt_handler = xadc_axi_interrupt_handler,
 	.flags = XADC_FLAGS_BUFFERED,
 	.type = XADC_TYPE_S7,
+	/* Temp in C = (val * 503.975) / 2**bits - 273.15 */
+	.temp_scale = 503975,
+	.temp_offset = 273150,
 };
 
 static const struct xadc_ops xadc_us_axi_ops = {
@@ -575,6 +581,12 @@
 	.interrupt_handler = xadc_axi_interrupt_handler,
 	.flags = XADC_FLAGS_BUFFERED,
 	.type = XADC_TYPE_US,
+	/**
+	 * Values below are for UltraScale+ (SYSMONE4) using internal reference.
+	 * See https://docs.xilinx.com/v/u/en-US/ug580-ultrascale-sysmon
+	 */
+	.temp_scale = 509314,
+	.temp_offset = 280231,
 };
 
 static int _xadc_update_adc_reg(struct xadc *xadc, unsigned int reg,
@@ -946,8 +958,7 @@
 			*val2 = chan->scan_type.realbits;
 			return IIO_VAL_FRACTIONAL_LOG2;
 		case IIO_TEMP:
-			/* Temp in C = (val * 503.975) / 2**bits - 273.15 */
-			*val = 503975;
+			*val = xadc->ops->temp_scale;
 			*val2 = bits;
 			return IIO_VAL_FRACTIONAL_LOG2;
 		default:
@@ -955,7 +966,7 @@
 		}
 	case IIO_CHAN_INFO_OFFSET:
 		/* Only the temperature channel has an offset */
-		*val = -((273150 << bits) / 503975);
+		*val = -((xadc->ops->temp_offset << bits) / xadc->ops->temp_scale);
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		ret = xadc_read_samplerate(xadc);
@@ -1434,28 +1445,6 @@
 	if (ret)
 		return ret;
 
-	/* Disable all alarms */
-	ret = xadc_update_adc_reg(xadc, XADC_REG_CONF1, XADC_CONF1_ALARM_MASK,
-				  XADC_CONF1_ALARM_MASK);
-	if (ret)
-		return ret;
-
-	/* Set thresholds to min/max */
-	for (i = 0; i < 16; i++) {
-		/*
-		 * Set max voltage threshold and both temperature thresholds to
-		 * 0xffff, min voltage threshold to 0.
-		 */
-		if (i % 8 < 4 || i == 7)
-			xadc->threshold[i] = 0xffff;
-		else
-			xadc->threshold[i] = 0;
-		ret = xadc_write_adc_reg(xadc, XADC_REG_THRESHOLD(i),
-			xadc->threshold[i]);
-		if (ret)
-			return ret;
-	}
-
 	/* Go to non-buffered mode */
 	xadc_postdisable(indio_dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/adc/xilinx-xadc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/adc/xilinx-xadc.h
@@ -86,6 +86,8 @@
 
 	unsigned int flags;
 	enum xadc_type type;
+	int temp_scale;
+	int temp_offset;
 };
 
 static inline int _xadc_read_adc_reg(struct xadc *xadc, unsigned int reg,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/addac/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/addac/Kconfig
@@ -0,0 +1,24 @@
+#
+# ADC DAC drivers
+#
+# When adding new entries keep the list in alphabetical order
+
+menu "Analog to digital and digital to analog converters"
+
+config STX104
+	tristate "Apex Embedded Systems STX104 driver"
+	depends on PC104 && X86
+	select ISA_BUS_API
+	select GPIOLIB
+	help
+	  Say yes here to build support for the Apex Embedded Systems STX104
+	  integrated analog PC/104 card.
+
+	  This driver supports the 16 channels of single-ended (8 channels of
+	  differential) analog inputs, 2 channels of analog output, 4 digital
+	  inputs, and 4 digital outputs provided by the STX104.
+
+	  The base port addresses for the devices may be configured via the base
+	  array module parameter.
+
+endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/addac/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/addac/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for industrial I/O ADDAC drivers
+#
+
+# When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_STX104) += stx104.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/addac/stx104.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/addac/stx104.c
@@ -0,0 +1,414 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IIO driver for the Apex Embedded Systems STX104
+ * Copyright (C) 2016 William Breathitt Gray
+ */
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gpio/driver.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/types.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/isa.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+#define STX104_OUT_CHAN(chan) {				\
+	.type = IIO_VOLTAGE,				\
+	.channel = chan,				\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),	\
+	.indexed = 1,					\
+	.output = 1					\
+}
+#define STX104_IN_CHAN(chan, diff) {					\
+	.type = IIO_VOLTAGE,						\
+	.channel = chan,						\
+	.channel2 = chan,						\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_HARDWAREGAIN) |	\
+		BIT(IIO_CHAN_INFO_OFFSET) | BIT(IIO_CHAN_INFO_SCALE),	\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),			\
+	.indexed = 1,							\
+	.differential = diff						\
+}
+
+#define STX104_NUM_OUT_CHAN 2
+
+#define STX104_EXTENT 16
+
+static unsigned int base[max_num_isa_dev(STX104_EXTENT)];
+static unsigned int num_stx104;
+module_param_hw_array(base, uint, ioport, &num_stx104, 0);
+MODULE_PARM_DESC(base, "Apex Embedded Systems STX104 base addresses");
+
+/**
+ * struct stx104_reg - device register structure
+ * @ssr_ad:	Software Strobe Register and ADC Data
+ * @achan:	ADC Channel
+ * @dio:	Digital I/O
+ * @dac:	DAC Channels
+ * @cir_asr:	Clear Interrupts and ADC Status
+ * @acr:	ADC Control
+ * @pccr_fsh:	Pacer Clock Control and FIFO Status MSB
+ * @acfg:	ADC Configuration
+ */
+struct stx104_reg {
+	u16 ssr_ad;
+	u8 achan;
+	u8 dio;
+	u16 dac[2];
+	u8 cir_asr;
+	u8 acr;
+	u8 pccr_fsh;
+	u8 acfg;
+};
+
+/**
+ * struct stx104_iio - IIO device private data structure
+ * @lock: synchronization lock to prevent I/O race conditions
+ * @chan_out_states:	channels' output states
+ * @reg:		I/O address offset for the device registers
+ */
+struct stx104_iio {
+	struct mutex lock;
+	unsigned int chan_out_states[STX104_NUM_OUT_CHAN];
+	struct stx104_reg __iomem *reg;
+};
+
+/**
+ * struct stx104_gpio - GPIO device private data structure
+ * @chip:	instance of the gpio_chip
+ * @lock:	synchronization lock to prevent I/O race conditions
+ * @base:	base port address of the GPIO device
+ * @out_state:	output bits state
+ */
+struct stx104_gpio {
+	struct gpio_chip chip;
+	spinlock_t lock;
+	u8 __iomem *base;
+	unsigned int out_state;
+};
+
+static int stx104_read_raw(struct iio_dev *indio_dev,
+	struct iio_chan_spec const *chan, int *val, int *val2, long mask)
+{
+	struct stx104_iio *const priv = iio_priv(indio_dev);
+	struct stx104_reg __iomem *const reg = priv->reg;
+	unsigned int adc_config;
+	int adbu;
+	int gain;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_HARDWAREGAIN:
+		/* get gain configuration */
+		adc_config = ioread8(&reg->acfg);
+		gain = adc_config & 0x3;
+
+		*val = 1 << gain;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_RAW:
+		if (chan->output) {
+			*val = priv->chan_out_states[chan->channel];
+			return IIO_VAL_INT;
+		}
+
+		mutex_lock(&priv->lock);
+
+		/* select ADC channel */
+		iowrite8(chan->channel | (chan->channel << 4), &reg->achan);
+
+		/* trigger ADC sample capture by writing to the 8-bit
+		 * Software Strobe Register and wait for completion
+		 */
+		iowrite8(0, &reg->ssr_ad);
+		while (ioread8(&reg->cir_asr) & BIT(7));
+
+		*val = ioread16(&reg->ssr_ad);
+
+		mutex_unlock(&priv->lock);
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_OFFSET:
+		/* get ADC bipolar/unipolar configuration */
+		adc_config = ioread8(&reg->acfg);
+		adbu = !(adc_config & BIT(2));
+
+		*val = -32768 * adbu;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		/* get ADC bipolar/unipolar and gain configuration */
+		adc_config = ioread8(&reg->acfg);
+		adbu = !(adc_config & BIT(2));
+		gain = adc_config & 0x3;
+
+		*val = 5;
+		*val2 = 15 - adbu + gain;
+		return IIO_VAL_FRACTIONAL_LOG2;
+	}
+
+	return -EINVAL;
+}
+
+static int stx104_write_raw(struct iio_dev *indio_dev,
+	struct iio_chan_spec const *chan, int val, int val2, long mask)
+{
+	struct stx104_iio *const priv = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_HARDWAREGAIN:
+		/* Only four gain states (x1, x2, x4, x8) */
+		switch (val) {
+		case 1:
+			iowrite8(0, &priv->reg->acfg);
+			break;
+		case 2:
+			iowrite8(1, &priv->reg->acfg);
+			break;
+		case 4:
+			iowrite8(2, &priv->reg->acfg);
+			break;
+		case 8:
+			iowrite8(3, &priv->reg->acfg);
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		return 0;
+	case IIO_CHAN_INFO_RAW:
+		if (chan->output) {
+			/* DAC can only accept up to a 16-bit value */
+			if ((unsigned int)val > 65535)
+				return -EINVAL;
+
+			mutex_lock(&priv->lock);
+
+			priv->chan_out_states[chan->channel] = val;
+			iowrite16(val, &priv->reg->dac[chan->channel]);
+
+			mutex_unlock(&priv->lock);
+			return 0;
+		}
+		return -EINVAL;
+	}
+
+	return -EINVAL;
+}
+
+static const struct iio_info stx104_info = {
+	.read_raw = stx104_read_raw,
+	.write_raw = stx104_write_raw
+};
+
+/* single-ended input channels configuration */
+static const struct iio_chan_spec stx104_channels_sing[] = {
+	STX104_OUT_CHAN(0), STX104_OUT_CHAN(1),
+	STX104_IN_CHAN(0, 0), STX104_IN_CHAN(1, 0), STX104_IN_CHAN(2, 0),
+	STX104_IN_CHAN(3, 0), STX104_IN_CHAN(4, 0), STX104_IN_CHAN(5, 0),
+	STX104_IN_CHAN(6, 0), STX104_IN_CHAN(7, 0), STX104_IN_CHAN(8, 0),
+	STX104_IN_CHAN(9, 0), STX104_IN_CHAN(10, 0), STX104_IN_CHAN(11, 0),
+	STX104_IN_CHAN(12, 0), STX104_IN_CHAN(13, 0), STX104_IN_CHAN(14, 0),
+	STX104_IN_CHAN(15, 0)
+};
+/* differential input channels configuration */
+static const struct iio_chan_spec stx104_channels_diff[] = {
+	STX104_OUT_CHAN(0), STX104_OUT_CHAN(1),
+	STX104_IN_CHAN(0, 1), STX104_IN_CHAN(1, 1), STX104_IN_CHAN(2, 1),
+	STX104_IN_CHAN(3, 1), STX104_IN_CHAN(4, 1), STX104_IN_CHAN(5, 1),
+	STX104_IN_CHAN(6, 1), STX104_IN_CHAN(7, 1)
+};
+
+static int stx104_gpio_get_direction(struct gpio_chip *chip,
+	unsigned int offset)
+{
+	/* GPIO 0-3 are input only, while the rest are output only */
+	if (offset < 4)
+		return 1;
+
+	return 0;
+}
+
+static int stx104_gpio_direction_input(struct gpio_chip *chip,
+	unsigned int offset)
+{
+	if (offset >= 4)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int stx104_gpio_direction_output(struct gpio_chip *chip,
+	unsigned int offset, int value)
+{
+	if (offset < 4)
+		return -EINVAL;
+
+	chip->set(chip, offset, value);
+	return 0;
+}
+
+static int stx104_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct stx104_gpio *const stx104gpio = gpiochip_get_data(chip);
+
+	if (offset >= 4)
+		return -EINVAL;
+
+	return !!(ioread8(stx104gpio->base) & BIT(offset));
+}
+
+static int stx104_gpio_get_multiple(struct gpio_chip *chip, unsigned long *mask,
+	unsigned long *bits)
+{
+	struct stx104_gpio *const stx104gpio = gpiochip_get_data(chip);
+
+	*bits = ioread8(stx104gpio->base);
+
+	return 0;
+}
+
+static void stx104_gpio_set(struct gpio_chip *chip, unsigned int offset,
+	int value)
+{
+	struct stx104_gpio *const stx104gpio = gpiochip_get_data(chip);
+	const unsigned int mask = BIT(offset) >> 4;
+	unsigned long flags;
+
+	if (offset < 4)
+		return;
+
+	spin_lock_irqsave(&stx104gpio->lock, flags);
+
+	if (value)
+		stx104gpio->out_state |= mask;
+	else
+		stx104gpio->out_state &= ~mask;
+
+	iowrite8(stx104gpio->out_state, stx104gpio->base);
+
+	spin_unlock_irqrestore(&stx104gpio->lock, flags);
+}
+
+#define STX104_NGPIO 8
+static const char *stx104_names[STX104_NGPIO] = {
+	"DIN0", "DIN1", "DIN2", "DIN3", "DOUT0", "DOUT1", "DOUT2", "DOUT3"
+};
+
+static void stx104_gpio_set_multiple(struct gpio_chip *chip,
+	unsigned long *mask, unsigned long *bits)
+{
+	struct stx104_gpio *const stx104gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+
+	/* verify masked GPIO are output */
+	if (!(*mask & 0xF0))
+		return;
+
+	*mask >>= 4;
+	*bits >>= 4;
+
+	spin_lock_irqsave(&stx104gpio->lock, flags);
+
+	stx104gpio->out_state &= ~*mask;
+	stx104gpio->out_state |= *mask & *bits;
+	iowrite8(stx104gpio->out_state, stx104gpio->base);
+
+	spin_unlock_irqrestore(&stx104gpio->lock, flags);
+}
+
+static int stx104_probe(struct device *dev, unsigned int id)
+{
+	struct iio_dev *indio_dev;
+	struct stx104_iio *priv;
+	struct stx104_gpio *stx104gpio;
+	int err;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	stx104gpio = devm_kzalloc(dev, sizeof(*stx104gpio), GFP_KERNEL);
+	if (!stx104gpio)
+		return -ENOMEM;
+
+	if (!devm_request_region(dev, base[id], STX104_EXTENT,
+		dev_name(dev))) {
+		dev_err(dev, "Unable to lock port addresses (0x%X-0x%X)\n",
+			base[id], base[id] + STX104_EXTENT);
+		return -EBUSY;
+	}
+
+	priv = iio_priv(indio_dev);
+	priv->reg = devm_ioport_map(dev, base[id], STX104_EXTENT);
+	if (!priv->reg)
+		return -ENOMEM;
+
+	indio_dev->info = &stx104_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	/* determine if differential inputs */
+	if (ioread8(&priv->reg->cir_asr) & BIT(5)) {
+		indio_dev->num_channels = ARRAY_SIZE(stx104_channels_diff);
+		indio_dev->channels = stx104_channels_diff;
+	} else {
+		indio_dev->num_channels = ARRAY_SIZE(stx104_channels_sing);
+		indio_dev->channels = stx104_channels_sing;
+	}
+
+	indio_dev->name = dev_name(dev);
+
+	mutex_init(&priv->lock);
+
+	/* configure device for software trigger operation */
+	iowrite8(0, &priv->reg->acr);
+
+	/* initialize gain setting to x1 */
+	iowrite8(0, &priv->reg->acfg);
+
+	/* initialize DAC output to 0V */
+	iowrite16(0, &priv->reg->dac[0]);
+	iowrite16(0, &priv->reg->dac[1]);
+
+	stx104gpio->chip.label = dev_name(dev);
+	stx104gpio->chip.parent = dev;
+	stx104gpio->chip.owner = THIS_MODULE;
+	stx104gpio->chip.base = -1;
+	stx104gpio->chip.ngpio = STX104_NGPIO;
+	stx104gpio->chip.names = stx104_names;
+	stx104gpio->chip.get_direction = stx104_gpio_get_direction;
+	stx104gpio->chip.direction_input = stx104_gpio_direction_input;
+	stx104gpio->chip.direction_output = stx104_gpio_direction_output;
+	stx104gpio->chip.get = stx104_gpio_get;
+	stx104gpio->chip.get_multiple = stx104_gpio_get_multiple;
+	stx104gpio->chip.set = stx104_gpio_set;
+	stx104gpio->chip.set_multiple = stx104_gpio_set_multiple;
+	stx104gpio->base = &priv->reg->dio;
+	stx104gpio->out_state = 0x0;
+
+	spin_lock_init(&stx104gpio->lock);
+
+	err = devm_gpiochip_add_data(dev, &stx104gpio->chip, stx104gpio);
+	if (err) {
+		dev_err(dev, "GPIO registering failed (%d)\n", err);
+		return err;
+	}
+
+	return devm_iio_device_register(dev, indio_dev);
+}
+
+static struct isa_driver stx104_driver = {
+	.probe = stx104_probe,
+	.driver = {
+		.name = "stx104"
+	},
+};
+
+module_isa_driver(stx104_driver, num_stx104);
+
+MODULE_AUTHOR("William Breathitt Gray <vilhelm.gray@gmail.com>");
+MODULE_DESCRIPTION("Apex Embedded Systems STX104 IIO driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/afe/iio-rescale.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/afe/iio-rescale.c
@@ -3,43 +3,91 @@
  * IIO rescale driver
  *
  * Copyright (C) 2018 Axentia Technologies AB
+ * Copyright (C) 2022 Liam Beguin <liambeguin@gmail.com>
  *
  * Author: Peter Rosin <peda@axentia.se>
  */
 
 #include <linux/err.h>
 #include <linux/gcd.h>
-#include <linux/iio/consumer.h>
-#include <linux/iio/iio.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/property.h>
 
-struct rescale;
+#include <linux/iio/afe/rescale.h>
+#include <linux/iio/consumer.h>
+#include <linux/iio/iio.h>
 
-struct rescale_cfg {
-	enum iio_chan_type type;
-	int (*props)(struct device *dev, struct rescale *rescale);
-};
+int rescale_process_scale(struct rescale *rescale, int scale_type,
+			  int *val, int *val2)
+{
+	s64 tmp;
 
-struct rescale {
-	const struct rescale_cfg *cfg;
-	struct iio_channel *source;
-	struct iio_chan_spec chan;
-	struct iio_chan_spec_ext_info *ext_info;
-	bool chan_processed;
-	s32 numerator;
-	s32 denominator;
-};
+	switch (scale_type) {
+	case IIO_VAL_FRACTIONAL:
+		*val *= rescale->numerator;
+		*val2 *= rescale->denominator;
+		return scale_type;
+	case IIO_VAL_INT:
+		*val *= rescale->numerator;
+		if (rescale->denominator == 1)
+			return scale_type;
+		*val2 = rescale->denominator;
+		return IIO_VAL_FRACTIONAL;
+	case IIO_VAL_FRACTIONAL_LOG2:
+		tmp = (s64)*val * 1000000000LL;
+		tmp = div_s64(tmp, rescale->denominator);
+		tmp *= rescale->numerator;
+		tmp = div_s64(tmp, 1000000000LL);
+		*val = tmp;
+		return scale_type;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+int rescale_process_offset(struct rescale *rescale, int scale_type,
+			   int scale, int scale2, int schan_off,
+			   int *val, int *val2)
+{
+	s64 tmp, tmp2;
+
+	switch (scale_type) {
+	case IIO_VAL_FRACTIONAL:
+		tmp = (s64)rescale->offset * scale2;
+		*val = div_s64(tmp, scale) + schan_off;
+		return IIO_VAL_INT;
+	case IIO_VAL_INT:
+		*val = div_s64(rescale->offset, scale) + schan_off;
+		return IIO_VAL_INT;
+	case IIO_VAL_FRACTIONAL_LOG2:
+		tmp = (s64)rescale->offset * (1 << scale2);
+		*val = div_s64(tmp, scale) + schan_off;
+		return IIO_VAL_INT;
+	case IIO_VAL_INT_PLUS_NANO:
+		tmp = (s64)rescale->offset * 1000000000LL;
+		tmp2 = ((s64)scale * 1000000000LL) + scale2;
+		*val = div64_s64(tmp, tmp2) + schan_off;
+		return IIO_VAL_INT;
+	case IIO_VAL_INT_PLUS_MICRO:
+		tmp = (s64)rescale->offset * 1000000LL;
+		tmp2 = ((s64)scale * 1000000LL) + scale2;
+		*val = div64_s64(tmp, tmp2) + schan_off;
+		return IIO_VAL_INT;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
 
 static int rescale_read_raw(struct iio_dev *indio_dev,
 			    struct iio_chan_spec const *chan,
 			    int *val, int *val2, long mask)
 {
 	struct rescale *rescale = iio_priv(indio_dev);
-	unsigned long long tmp;
+	int scale, scale2;
+	int schan_off = 0;
 	int ret;
 
 	switch (mask) {
@@ -65,27 +113,58 @@
 		} else {
 			ret = iio_read_channel_scale(rescale->source, val, val2);
 		}
-		switch (ret) {
-		case IIO_VAL_FRACTIONAL:
-			*val *= rescale->numerator;
-			*val2 *= rescale->denominator;
-			return ret;
-		case IIO_VAL_INT:
-			*val *= rescale->numerator;
-			if (rescale->denominator == 1)
-				return ret;
-			*val2 = rescale->denominator;
-			return IIO_VAL_FRACTIONAL;
-		case IIO_VAL_FRACTIONAL_LOG2:
-			tmp = *val * 1000000000LL;
-			do_div(tmp, rescale->denominator);
-			tmp *= rescale->numerator;
-			do_div(tmp, 1000000000LL);
-			*val = tmp;
-			return ret;
-		default:
-			return -EOPNOTSUPP;
+		return rescale_process_scale(rescale, ret, val, val2);
+	case IIO_CHAN_INFO_OFFSET:
+		/*
+		 * Processed channels are scaled 1-to-1 and source offset is
+		 * already taken into account.
+		 *
+		 * In other cases, real world measurement are expressed as:
+		 *
+		 *	schan_scale * (raw + schan_offset)
+		 *
+		 * Given that the rescaler parameters are applied recursively:
+		 *
+		 *	rescaler_scale * (schan_scale * (raw + schan_offset) +
+		 *		rescaler_offset)
+		 *
+		 * Or,
+		 *
+		 *	(rescaler_scale * schan_scale) * (raw +
+		 *		(schan_offset +	rescaler_offset / schan_scale)
+		 *
+		 * Thus, reusing the original expression the parameters exposed
+		 * to userspace are:
+		 *
+		 *	scale = schan_scale * rescaler_scale
+		 *	offset = schan_offset + rescaler_offset / schan_scale
+		 */
+		if (rescale->chan_processed) {
+			*val = rescale->offset;
+			return IIO_VAL_INT;
+		}
+
+		if (iio_channel_has_info(rescale->source->channel,
+					 IIO_CHAN_INFO_OFFSET)) {
+			ret = iio_read_channel_offset(rescale->source,
+						      &schan_off, NULL);
+			if (ret != IIO_VAL_INT)
+				return ret < 0 ? ret : -EOPNOTSUPP;
+		}
+
+		if (iio_channel_has_info(rescale->source->channel,
+					 IIO_CHAN_INFO_SCALE)) {
+			ret = iio_read_channel_scale(rescale->source, &scale, &scale2);
+			return rescale_process_offset(rescale, ret, scale, scale2,
+						      schan_off, val, val2);
 		}
+
+		/*
+		 * If we get here we have no scale so scale 1:1 but apply
+		 * rescaler and offset, if any.
+		 */
+		return rescale_process_offset(rescale, IIO_VAL_FRACTIONAL, 1, 1,
+					      schan_off, val, val2);
 	default:
 		return -EINVAL;
 	}
@@ -148,9 +227,10 @@
 	chan->ext_info = rescale->ext_info;
 	chan->type = rescale->cfg->type;
 
-	if (iio_channel_has_info(schan, IIO_CHAN_INFO_RAW) ||
-	    iio_channel_has_info(schan, IIO_CHAN_INFO_SCALE)) {
-		dev_info(dev, "using raw+scale source channel\n");
+	if (iio_channel_has_info(schan, IIO_CHAN_INFO_RAW) &&
+	    (iio_channel_has_info(schan, IIO_CHAN_INFO_SCALE) ||
+	     iio_channel_has_info(schan, IIO_CHAN_INFO_OFFSET))) {
+		dev_info(dev, "using raw+scale/offset source channel\n");
 	} else if (iio_channel_has_info(schan, IIO_CHAN_INFO_PROCESSED)) {
 		dev_info(dev, "using processed channel\n");
 		rescale->chan_processed = true;
@@ -162,6 +242,9 @@
 	chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
 		BIT(IIO_CHAN_INFO_SCALE);
 
+	if (rescale->offset)
+		chan->info_mask_separate |= BIT(IIO_CHAN_INFO_OFFSET);
+
 	/*
 	 * Using .read_avail() is fringe to begin with and makes no sense
 	 * whatsoever for processed channels, so we make sure that this cannot
@@ -326,6 +409,7 @@
 	rescale->cfg = of_device_get_match_data(dev);
 	rescale->numerator = 1;
 	rescale->denominator = 1;
+	rescale->offset = 0;
 
 	ret = rescale->cfg->props(dev, rescale);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/buffer/industrialio-buffer-dmaengine.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/buffer/industrialio-buffer-dmaengine.c
@@ -180,7 +180,7 @@
 
 	ret = dma_get_slave_caps(chan, &caps);
 	if (ret < 0)
-		goto err_free;
+		goto err_release;
 
 	/* Needs to be aligned to the maximum of the minimums */
 	if (caps.src_addr_widths)
@@ -206,6 +206,8 @@
 
 	return &dmaengine_buffer->queue.buffer;
 
+err_release:
+	dma_release_channel(chan);
 err_free:
 	kfree(dmaengine_buffer);
 	return ERR_PTR(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/buffer/industrialio-triggered-buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/buffer/industrialio-triggered-buffer.c
@@ -44,6 +44,16 @@
 	struct iio_buffer *buffer;
 	int ret;
 
+	/*
+	 * iio_triggered_buffer_cleanup() assumes that the buffer allocated here
+	 * is assigned to indio_dev->buffer but this is only the case if this
+	 * function is the first caller to iio_device_attach_buffer(). If
+	 * indio_dev->buffer is already set then we can't proceed otherwise the
+	 * cleanup function will try to free a buffer that was not allocated here.
+	 */
+	if (indio_dev->buffer)
+		return -EADDRINUSE;
+
 	buffer = iio_kfifo_allocate();
 	if (!buffer) {
 		ret = -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/chemical/bme680.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/chemical/bme680.h
@@ -54,7 +54,9 @@
 #define   BME680_NB_CONV_MASK			GENMASK(3, 0)
 
 #define BME680_REG_MEAS_STAT_0			0x1D
+#define   BME680_NEW_DATA_BIT			BIT(7)
 #define   BME680_GAS_MEAS_BIT			BIT(6)
+#define   BME680_MEAS_BIT			BIT(5)
 
 /* Calibration Parameters */
 #define BME680_T2_LSB_REG	0x8A
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/chemical/bme680_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/chemical/bme680_core.c
@@ -10,6 +10,7 @@
  */
 #include <linux/acpi.h>
 #include <linux/bitfield.h>
+#include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/module.h>
 #include <linux/log2.h>
@@ -38,7 +39,7 @@
 	s8  par_h3;
 	s8  par_h4;
 	s8  par_h5;
-	s8  par_h6;
+	u8  par_h6;
 	s8  par_h7;
 	s8  par_gh1;
 	s16 par_gh2;
@@ -342,10 +343,10 @@
 	if (!calib->par_t2)
 		bme680_read_calib(data, calib);
 
-	var1 = (adc_temp >> 3) - (calib->par_t1 << 1);
+	var1 = (adc_temp >> 3) - ((s32)calib->par_t1 << 1);
 	var2 = (var1 * calib->par_t2) >> 11;
 	var3 = ((var1 >> 1) * (var1 >> 1)) >> 12;
-	var3 = (var3 * (calib->par_t3 << 4)) >> 14;
+	var3 = (var3 * ((s32)calib->par_t3 << 4)) >> 14;
 	data->t_fine = var2 + var3;
 	calc_temp = (data->t_fine * 5 + 128) >> 8;
 
@@ -368,9 +369,9 @@
 	var1 = (data->t_fine >> 1) - 64000;
 	var2 = ((((var1 >> 2) * (var1 >> 2)) >> 11) * calib->par_p6) >> 2;
 	var2 = var2 + (var1 * calib->par_p5 << 1);
-	var2 = (var2 >> 2) + (calib->par_p4 << 16);
+	var2 = (var2 >> 2) + ((s32)calib->par_p4 << 16);
 	var1 = (((((var1 >> 2) * (var1 >> 2)) >> 13) *
-			(calib->par_p3 << 5)) >> 3) +
+			((s32)calib->par_p3 << 5)) >> 3) +
 			((calib->par_p2 * var1) >> 1);
 	var1 = var1 >> 18;
 	var1 = ((32768 + var1) * calib->par_p1) >> 15;
@@ -388,7 +389,7 @@
 	var3 = ((press_comp >> 8) * (press_comp >> 8) *
 			(press_comp >> 8) * calib->par_p10) >> 17;
 
-	press_comp += (var1 + var2 + var3 + (calib->par_p7 << 7)) >> 4;
+	press_comp += (var1 + var2 + var3 + ((s32)calib->par_p7 << 7)) >> 4;
 
 	return press_comp;
 }
@@ -414,7 +415,7 @@
 		 (((temp_scaled * ((temp_scaled * calib->par_h5) / 100))
 		   >> 6) / 100) + (1 << 14))) >> 10;
 	var3 = var1 * var2;
-	var4 = calib->par_h6 << 7;
+	var4 = (s32)calib->par_h6 << 7;
 	var4 = (var4 + ((temp_scaled * calib->par_h7) / 100)) >> 4;
 	var5 = ((var3 >> 14) * (var3 >> 14)) >> 10;
 	var6 = (var4 * var5) >> 1;
@@ -532,6 +533,43 @@
 	return ilog2(val) + 1;
 }
 
+/*
+ * Taken from Bosch BME680 API:
+ * https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L490
+ */
+static int bme680_wait_for_eoc(struct bme680_data *data)
+{
+	struct device *dev = regmap_get_device(data->regmap);
+	unsigned int check;
+	int ret;
+	/*
+	 * (Sum of oversampling ratios * time per oversampling) +
+	 * TPH measurement + gas measurement + wait transition from forced mode
+	 * + heater duration
+	 */
+	int wait_eoc_us = ((data->oversampling_temp + data->oversampling_press +
+			   data->oversampling_humid) * 1936) + (477 * 4) +
+			   (477 * 5) + 1000 + (data->heater_dur * 1000);
+
+	usleep_range(wait_eoc_us, wait_eoc_us + 100);
+
+	ret = regmap_read(data->regmap, BME680_REG_MEAS_STAT_0, &check);
+	if (ret) {
+		dev_err(dev, "failed to read measurement status register.\n");
+		return ret;
+	}
+	if (check & BME680_MEAS_BIT) {
+		dev_err(dev, "Device measurement cycle incomplete.\n");
+		return -EBUSY;
+	}
+	if (!(check & BME680_NEW_DATA_BIT)) {
+		dev_err(dev, "No new data available from the device.\n");
+		return -ENODATA;
+	}
+
+	return 0;
+}
+
 static int bme680_chip_config(struct bme680_data *data)
 {
 	struct device *dev = regmap_get_device(data->regmap);
@@ -622,6 +660,10 @@
 	if (ret < 0)
 		return ret;
 
+	ret = bme680_wait_for_eoc(data);
+	if (ret)
+		return ret;
+
 	ret = regmap_bulk_read(data->regmap, BME680_REG_TEMP_MSB,
 			       &tmp, 3);
 	if (ret < 0) {
@@ -678,7 +720,7 @@
 	}
 
 	*val = bme680_compensate_press(data, adc_press);
-	*val2 = 100;
+	*val2 = 1000;
 	return IIO_VAL_FRACTIONAL;
 }
 
@@ -738,6 +780,10 @@
 	if (ret < 0)
 		return ret;
 
+	ret = bme680_wait_for_eoc(data);
+	if (ret)
+		return ret;
+
 	ret = regmap_read(data->regmap, BME680_REG_MEAS_STAT_0, &check);
 	if (check & BME680_GAS_MEAS_BIT) {
 		dev_err(dev, "gas measurement incomplete\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/chemical/ccs811.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/chemical/ccs811.c
@@ -499,11 +499,11 @@
 
 		data->drdy_trig->ops = &ccs811_trigger_ops;
 		iio_trigger_set_drvdata(data->drdy_trig, indio_dev);
-		indio_dev->trig = data->drdy_trig;
-		iio_trigger_get(indio_dev->trig);
 		ret = iio_trigger_register(data->drdy_trig);
 		if (ret)
 			goto err_poweroff;
+
+		indio_dev->trig = iio_trigger_get(data->drdy_trig);
 	}
 
 	ret = iio_triggered_buffer_setup(indio_dev, NULL,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/common/cros_ec_sensors/cros_ec_lid_angle.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/common/cros_ec_sensors/cros_ec_lid_angle.c
@@ -97,7 +97,7 @@
 	if (!indio_dev)
 		return -ENOMEM;
 
-	ret = cros_ec_sensors_core_init(pdev, indio_dev, false, NULL, NULL);
+	ret = cros_ec_sensors_core_init(pdev, indio_dev, false, NULL);
 	if (ret)
 		return ret;
 
@@ -113,7 +113,7 @@
 	if (ret)
 		return ret;
 
-	return devm_iio_device_register(dev, indio_dev);
+	return cros_ec_sensors_core_register(dev, indio_dev, NULL);
 }
 
 static const struct platform_device_id cros_ec_lid_angle_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/common/cros_ec_sensors/cros_ec_sensors.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/common/cros_ec_sensors/cros_ec_sensors.c
@@ -235,8 +235,7 @@
 		return -ENOMEM;
 
 	ret = cros_ec_sensors_core_init(pdev, indio_dev, true,
-					cros_ec_sensors_capture,
-					cros_ec_sensors_push_data);
+					cros_ec_sensors_capture);
 	if (ret)
 		return ret;
 
@@ -297,7 +296,8 @@
 	else
 		state->core.read_ec_sensors_data = cros_ec_sensors_read_cmd;
 
-	return devm_iio_device_register(dev, indio_dev);
+	return cros_ec_sensors_core_register(dev, indio_dev,
+			cros_ec_sensors_push_data);
 }
 
 static const struct platform_device_id cros_ec_sensors_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c
@@ -196,8 +196,11 @@
 	/*
 	 * Ignore samples if the buffer is not set: it is needed if the ODR is
 	 * set but the buffer is not enabled yet.
+	 *
+	 * Note: iio_device_claim_buffer_mode() returns -EBUSY if the buffer
+	 * is not enabled.
 	 */
-	if (!iio_buffer_enabled(indio_dev))
+	if (iio_device_claim_buffer_mode(indio_dev) < 0)
 		return 0;
 
 	out = (s16 *)st->samples;
@@ -216,6 +219,7 @@
 	iio_push_to_buffers_with_timestamp(indio_dev, st->samples,
 					   timestamp + delta);
 
+	iio_device_release_buffer_mode(indio_dev);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(cros_ec_sensors_push_data);
@@ -234,21 +238,18 @@
 
 /**
  * cros_ec_sensors_core_init() - basic initialization of the core structure
- * @pdev:		platform device created for the sensors
+ * @pdev:		platform device created for the sensor
  * @indio_dev:		iio device structure of the device
  * @physical_device:	true if the device refers to a physical device
  * @trigger_capture:    function pointer to call buffer is triggered,
  *    for backward compatibility.
- * @push_data:          function to call when cros_ec_sensorhub receives
- *    a sample for that sensor.
  *
  * Return: 0 on success, -errno on failure.
  */
 int cros_ec_sensors_core_init(struct platform_device *pdev,
 			      struct iio_dev *indio_dev,
 			      bool physical_device,
-			      cros_ec_sensors_capture_t trigger_capture,
-			      cros_ec_sensorhub_push_data_cb_t push_data)
+			      cros_ec_sensors_capture_t trigger_capture)
 {
 	struct device *dev = &pdev->dev;
 	struct cros_ec_sensors_core_state *state = iio_priv(indio_dev);
@@ -262,7 +263,7 @@
 	platform_set_drvdata(pdev, indio_dev);
 
 	state->ec = ec->ec_dev;
-	state->msg = devm_kzalloc(&pdev->dev,
+	state->msg = devm_kzalloc(&pdev->dev, sizeof(*state->msg) +
 				max((u16)sizeof(struct ec_params_motion_sense),
 				state->ec->max_response), GFP_KERNEL);
 	if (!state->msg)
@@ -339,17 +340,6 @@
 			if (ret)
 				return ret;
 
-			ret = cros_ec_sensorhub_register_push_data(
-					sensor_hub, sensor_platform->sensor_num,
-					indio_dev, push_data);
-			if (ret)
-				return ret;
-
-			ret = devm_add_action_or_reset(
-					dev, cros_ec_sensors_core_clean, pdev);
-			if (ret)
-				return ret;
-
 			/* Timestamp coming from FIFO are in ns since boot. */
 			ret = iio_device_set_clock(indio_dev, CLOCK_BOOTTIME);
 			if (ret)
@@ -372,6 +362,46 @@
 EXPORT_SYMBOL_GPL(cros_ec_sensors_core_init);
 
 /**
+ * cros_ec_sensors_core_register() - Register callback to FIFO and IIO when
+ * sensor is ready.
+ * It must be called at the end of the sensor probe routine.
+ * @dev:		device created for the sensor
+ * @indio_dev:		iio device structure of the device
+ * @push_data:          function to call when cros_ec_sensorhub receives
+ *    a sample for that sensor.
+ *
+ * Return: 0 on success, -errno on failure.
+ */
+int cros_ec_sensors_core_register(struct device *dev,
+				  struct iio_dev *indio_dev,
+				  cros_ec_sensorhub_push_data_cb_t push_data)
+{
+	struct cros_ec_sensor_platform *sensor_platform = dev_get_platdata(dev);
+	struct cros_ec_sensorhub *sensor_hub = dev_get_drvdata(dev->parent);
+	struct platform_device *pdev = to_platform_device(dev);
+	struct cros_ec_dev *ec = sensor_hub->ec;
+	int ret;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret)
+		return ret;
+
+	if (!push_data ||
+	    !cros_ec_check_features(ec, EC_FEATURE_MOTION_SENSE_FIFO))
+		return 0;
+
+	ret = cros_ec_sensorhub_register_push_data(
+			sensor_hub, sensor_platform->sensor_num,
+			indio_dev, push_data);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(
+			dev, cros_ec_sensors_core_clean, pdev);
+}
+EXPORT_SYMBOL_GPL(cros_ec_sensors_core_register);
+
+/**
  * cros_ec_motion_send_host_cmd() - send motion sense host command
  * @state:		pointer to state information for device
  * @opt_length:	optional length to reduce the response size, useful on the data
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/common/hid-sensors/hid-sensor-trigger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/common/hid-sensors/hid-sensor-trigger.c
@@ -32,7 +32,7 @@
 	latency = integer * 1000 + fract / 1000;
 	ret = hid_sensor_set_report_latency(attrb, latency);
 	if (ret < 0)
-		return len;
+		return ret;
 
 	attrb->latency_ms = hid_sensor_get_report_latency(attrb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/common/ms_sensors/ms_sensors_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/common/ms_sensors/ms_sensors_i2c.c
@@ -15,8 +15,8 @@
 /* Conversion times in us */
 static const u16 ms_sensors_ht_t_conversion_time[] = { 50000, 25000,
 						       13000, 7000 };
-static const u16 ms_sensors_ht_h_conversion_time[] = { 16000, 3000,
-						       5000, 8000 };
+static const u16 ms_sensors_ht_h_conversion_time[] = { 16000, 5000,
+						       3000, 8000 };
 static const u16 ms_sensors_tp_conversion_time[] = { 500, 1100, 2100,
 						     4100, 8220, 16440 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/common/st_sensors/st_sensors_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/common/st_sensors/st_sensors_core.c
@@ -71,16 +71,18 @@
 
 int st_sensors_set_odr(struct iio_dev *indio_dev, unsigned int odr)
 {
-	int err;
+	int err = 0;
 	struct st_sensor_odr_avl odr_out = {0, 0};
 	struct st_sensor_data *sdata = iio_priv(indio_dev);
 
+	mutex_lock(&sdata->odr_lock);
+
 	if (!sdata->sensor_settings->odr.mask)
-		return 0;
+		goto unlock_mutex;
 
 	err = st_sensors_match_odr(sdata->sensor_settings, odr, &odr_out);
 	if (err < 0)
-		goto st_sensors_match_odr_error;
+		goto unlock_mutex;
 
 	if ((sdata->sensor_settings->odr.addr ==
 					sdata->sensor_settings->pw.addr) &&
@@ -103,7 +105,9 @@
 	if (err >= 0)
 		sdata->odr = odr_out.hz;
 
-st_sensors_match_odr_error:
+unlock_mutex:
+	mutex_unlock(&sdata->odr_lock);
+
 	return err;
 }
 EXPORT_SYMBOL(st_sensors_set_odr);
@@ -365,6 +369,8 @@
 	struct st_sensors_platform_data *of_pdata;
 	int err = 0;
 
+	mutex_init(&sdata->odr_lock);
+
 	/* If OF/DT pdata exists, it will take precedence of anything else */
 	of_pdata = st_sensors_dev_probe(indio_dev->dev.parent, pdata);
 	if (IS_ERR(of_pdata))
@@ -558,18 +564,24 @@
 		err = -EBUSY;
 		goto out;
 	} else {
+		mutex_lock(&sdata->odr_lock);
 		err = st_sensors_set_enable(indio_dev, true);
-		if (err < 0)
+		if (err < 0) {
+			mutex_unlock(&sdata->odr_lock);
 			goto out;
+		}
 
 		msleep((sdata->sensor_settings->bootime * 1000) / sdata->odr);
 		err = st_sensors_read_axis_data(indio_dev, ch, val);
-		if (err < 0)
+		if (err < 0) {
+			mutex_unlock(&sdata->odr_lock);
 			goto out;
+		}
 
 		*val = *val >> ch->scan_type.shift;
 
 		err = st_sensors_set_enable(indio_dev, false);
+		mutex_unlock(&sdata->odr_lock);
 	}
 out:
 	mutex_unlock(&indio_dev->mlock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/Kconfig
@@ -203,6 +203,7 @@
 config AD5770R
 	tristate "Analog Devices AD5770R IDAC driver"
 	depends on SPI_MASTER
+	select REGMAP_SPI
 	help
 	  Say yes here to build support for Analog Devices AD5770R Digital to
 	  Analog Converter.
@@ -283,6 +284,7 @@
 config LTC1660
 	tristate "Linear Technology LTC1660/LTC1665 DAC SPI driver"
 	depends on SPI
+	select REGMAP_SPI
 	help
 	  Say yes here to build support for Linear Technology
 	  LTC1660 and LTC1665 Digital to Analog Converters.
@@ -369,6 +371,7 @@
 
 config STM32_DAC_CORE
 	tristate
+	select REGMAP_MMIO
 
 config TI_DAC082S085
 	tristate "Texas Instruments 8/10/12-bit 2/4-channel DAC driver"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/Makefile
@@ -16,7 +16,7 @@
 obj-$(CONFIG_AD5592R) += ad5592r.o
 obj-$(CONFIG_AD5593R) += ad5593r.o
 obj-$(CONFIG_AD5755) += ad5755.o
-obj-$(CONFIG_AD5755) += ad5758.o
+obj-$(CONFIG_AD5758) += ad5758.o
 obj-$(CONFIG_AD5761) += ad5761.o
 obj-$(CONFIG_AD5764) += ad5764.o
 obj-$(CONFIG_AD5766) += ad5766.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/ad5446.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/ad5446.c
@@ -178,7 +178,7 @@
 
 	switch (m) {
 	case IIO_CHAN_INFO_RAW:
-		*val = st->cached_val;
+		*val = st->cached_val >> chan->scan_type.shift;
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SCALE:
 		*val = st->vref_mv;
@@ -531,8 +531,15 @@
 {
 	struct i2c_client *client = to_i2c_client(st->dev);
 	__be16 data = cpu_to_be16(val);
+	int ret;
 
-	return i2c_master_send(client, (char *)&data, sizeof(data));
+	ret = i2c_master_send(client, (char *)&data, sizeof(data));
+	if (ret < 0)
+		return ret;
+	if (ret != sizeof(data))
+		return -EIO;
+
+	return 0;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/ad5592r-base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/ad5592r-base.c
@@ -411,7 +411,7 @@
 			s64 tmp = *val * (3767897513LL / 25LL);
 			*val = div_s64_rem(tmp, 1000000000LL, val2);
 
-			return IIO_VAL_INT_PLUS_MICRO;
+			return IIO_VAL_INT_PLUS_NANO;
 		}
 
 		mutex_lock(&st->lock);
@@ -523,7 +523,7 @@
 		if (!ret)
 			st->channel_modes[reg] = tmp;
 
-		fwnode_property_read_u32(child, "adi,off-state", &tmp);
+		ret = fwnode_property_read_u32(child, "adi,off-state", &tmp);
 		if (!ret)
 			st->channel_offstate[reg] = tmp;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/ad5593r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/ad5593r.c
@@ -13,6 +13,8 @@
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
 
+#include <asm/unaligned.h>
+
 #define AD5593R_MODE_CONF		(0 << 4)
 #define AD5593R_MODE_DAC_WRITE		(1 << 4)
 #define AD5593R_MODE_ADC_READBACK	(4 << 4)
@@ -20,6 +22,24 @@
 #define AD5593R_MODE_GPIO_READBACK	(6 << 4)
 #define AD5593R_MODE_REG_READBACK	(7 << 4)
 
+static int ad5593r_read_word(struct i2c_client *i2c, u8 reg, u16 *value)
+{
+	int ret;
+	u8 buf[2];
+
+	ret = i2c_smbus_write_byte(i2c, reg);
+	if (ret < 0)
+		return ret;
+
+	ret = i2c_master_recv(i2c, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	*value = get_unaligned_be16(buf);
+
+	return 0;
+}
+
 static int ad5593r_write_dac(struct ad5592r_state *st, unsigned chan, u16 value)
 {
 	struct i2c_client *i2c = to_i2c_client(st->dev);
@@ -38,13 +58,7 @@
 	if (val < 0)
 		return (int) val;
 
-	val = i2c_smbus_read_word_swapped(i2c, AD5593R_MODE_ADC_READBACK);
-	if (val < 0)
-		return (int) val;
-
-	*value = (u16) val;
-
-	return 0;
+	return ad5593r_read_word(i2c, AD5593R_MODE_ADC_READBACK, value);
 }
 
 static int ad5593r_reg_write(struct ad5592r_state *st, u8 reg, u16 value)
@@ -58,25 +72,19 @@
 static int ad5593r_reg_read(struct ad5592r_state *st, u8 reg, u16 *value)
 {
 	struct i2c_client *i2c = to_i2c_client(st->dev);
-	s32 val;
-
-	val = i2c_smbus_read_word_swapped(i2c, AD5593R_MODE_REG_READBACK | reg);
-	if (val < 0)
-		return (int) val;
 
-	*value = (u16) val;
-
-	return 0;
+	return ad5593r_read_word(i2c, AD5593R_MODE_REG_READBACK | reg, value);
 }
 
 static int ad5593r_gpio_read(struct ad5592r_state *st, u8 *value)
 {
 	struct i2c_client *i2c = to_i2c_client(st->dev);
-	s32 val;
+	u16 val;
+	int ret;
 
-	val = i2c_smbus_read_word_swapped(i2c, AD5593R_MODE_GPIO_READBACK);
-	if (val < 0)
-		return (int) val;
+	ret = ad5593r_read_word(i2c, AD5593R_MODE_GPIO_READBACK, &val);
+	if (ret)
+		return ret;
 
 	*value = (u8) val;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/ad5766.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/ad5766.c
@@ -503,13 +503,13 @@
 	int i, ret, min, max, tmp[2];
 
 	ret = device_property_read_u32_array(&st->spi->dev,
-					     "output-range-voltage",
+					     "output-range-microvolts",
 					     tmp, 2);
 	if (ret)
 		return ret;
 
-	min = tmp[0] / 1000;
-	max = tmp[1] / 1000;
+	min = tmp[0] / 1000000;
+	max = tmp[1] / 1000000;
 	for (i = 0; i < ARRAY_SIZE(ad5766_span_tbl); i++) {
 		if (ad5766_span_tbl[i].min != min ||
 		    ad5766_span_tbl[i].max != max)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/ad5770r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/ad5770r.c
@@ -522,7 +522,7 @@
 		return -EINVAL;
 
 	device_for_each_child_node(&st->spi->dev, child) {
-		ret = fwnode_property_read_u32(child, "num", &num);
+		ret = fwnode_property_read_u32(child, "reg", &num);
 		if (ret)
 			goto err_child_out;
 		if (num >= AD5770R_MAX_CHANNELS) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/cio-dac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/cio-dac.c
@@ -66,8 +66,8 @@
 	if (mask != IIO_CHAN_INFO_RAW)
 		return -EINVAL;
 
-	/* DAC can only accept up to a 16-bit value */
-	if ((unsigned int)val > 65535)
+	/* DAC can only accept up to a 12-bit value */
+	if ((unsigned int)val > 4095)
 		return -EINVAL;
 
 	priv->chan_out_states[chan->channel] = val;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dac/mcp4725.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dac/mcp4725.c
@@ -47,12 +47,18 @@
 	struct mcp4725_data *data = iio_priv(i2c_get_clientdata(
 		to_i2c_client(dev)));
 	u8 outbuf[2];
+	int ret;
 
 	outbuf[0] = (data->powerdown_mode + 1) << 4;
 	outbuf[1] = 0;
 	data->powerdown = true;
 
-	return i2c_master_send(data->client, outbuf, 2);
+	ret = i2c_master_send(data->client, outbuf, 2);
+	if (ret < 0)
+		return ret;
+	else if (ret != 2)
+		return -EIO;
+	return 0;
 }
 
 static int __maybe_unused mcp4725_resume(struct device *dev)
@@ -60,13 +66,19 @@
 	struct mcp4725_data *data = iio_priv(i2c_get_clientdata(
 		to_i2c_client(dev)));
 	u8 outbuf[2];
+	int ret;
 
 	/* restore previous DAC value */
 	outbuf[0] = (data->dac_value >> 8) & 0xf;
 	outbuf[1] = data->dac_value & 0xff;
 	data->powerdown = false;
 
-	return i2c_master_send(data->client, outbuf, 2);
+	ret = i2c_master_send(data->client, outbuf, 2);
+	if (ret < 0)
+		return ret;
+	else if (ret != 2)
+		return -EIO;
+	return 0;
 }
 static SIMPLE_DEV_PM_OPS(mcp4725_pm_ops, mcp4725_suspend, mcp4725_resume);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dummy/iio_simple_dummy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dummy/iio_simple_dummy.c
@@ -575,10 +575,9 @@
 	 */
 
 	swd = kzalloc(sizeof(*swd), GFP_KERNEL);
-	if (!swd) {
-		ret = -ENOMEM;
-		goto error_kzalloc;
-	}
+	if (!swd)
+		return ERR_PTR(-ENOMEM);
+
 	/*
 	 * Allocate an IIO device.
 	 *
@@ -590,7 +589,7 @@
 	indio_dev = iio_device_alloc(parent, sizeof(*st));
 	if (!indio_dev) {
 		ret = -ENOMEM;
-		goto error_ret;
+		goto error_free_swd;
 	}
 
 	st = iio_priv(indio_dev);
@@ -616,6 +615,10 @@
 	 *    indio_dev->name = spi_get_device_id(spi)->name;
 	 */
 	indio_dev->name = kstrdup(name, GFP_KERNEL);
+	if (!indio_dev->name) {
+		ret = -ENOMEM;
+		goto error_free_device;
+	}
 
 	/* Provide description of available channels */
 	indio_dev->channels = iio_dummy_channels;
@@ -632,7 +635,7 @@
 
 	ret = iio_simple_dummy_events_register(indio_dev);
 	if (ret < 0)
-		goto error_free_device;
+		goto error_free_name;
 
 	ret = iio_simple_dummy_configure_buffer(indio_dev);
 	if (ret < 0)
@@ -649,11 +652,12 @@
 	iio_simple_dummy_unconfigure_buffer(indio_dev);
 error_unregister_events:
 	iio_simple_dummy_events_unregister(indio_dev);
+error_free_name:
+	kfree(indio_dev->name);
 error_free_device:
 	iio_device_free(indio_dev);
-error_ret:
+error_free_swd:
 	kfree(swd);
-error_kzalloc:
 	return ERR_PTR(ret);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/dummy/iio_simple_dummy_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/dummy/iio_simple_dummy_buffer.c
@@ -48,7 +48,7 @@
 	int len = 0;
 	u16 *data;
 
-	data = kmalloc(indio_dev->scan_bytes, GFP_KERNEL);
+	data = kzalloc(indio_dev->scan_bytes, GFP_KERNEL);
 	if (!data)
 		goto done;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/adis16136.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/adis16136.c
@@ -591,3 +591,4 @@
 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
 MODULE_DESCRIPTION("Analog Devices ADIS16133/ADIS16135/ADIS16136 gyroscope driver");
 MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/adis16260.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/adis16260.c
@@ -433,3 +433,4 @@
 MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>");
 MODULE_DESCRIPTION("Analog Devices ADIS16260/5 Digital Gyroscope Sensor");
 MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/adxrs290.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/adxrs290.c
@@ -7,6 +7,7 @@
  */
 
 #include <linux/bitfield.h>
+#include <linux/bitops.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/kernel.h>
@@ -124,7 +125,7 @@
 		goto err_unlock;
 	}
 
-	*val = temp;
+	*val = sign_extend32(temp, 15);
 
 err_unlock:
 	mutex_unlock(&st->lock);
@@ -146,7 +147,7 @@
 	}
 
 	/* extract lower 12 bits temperature reading */
-	*val = temp & 0x0FFF;
+	*val = sign_extend32(temp, 11);
 
 err_unlock:
 	mutex_unlock(&st->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/bmg160_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/bmg160_core.c
@@ -1188,11 +1188,14 @@
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(dev, "unable to register iio device\n");
-		goto err_buffer_cleanup;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(dev);
+	pm_runtime_disable(dev);
 err_buffer_cleanup:
 	iio_triggered_buffer_cleanup(indio_dev);
 err_trigger_unregister:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/fxas21002c_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/fxas21002c_core.c
@@ -730,14 +730,21 @@
 	int ret;
 
 	mutex_lock(&data->lock);
+	ret = fxas21002c_pm_get(data);
+	if (ret < 0)
+		goto out_unlock;
+
 	ret = regmap_bulk_read(data->regmap, FXAS21002C_REG_OUT_X_MSB,
 			       data->buffer, CHANNEL_SCAN_MAX * sizeof(s16));
 	if (ret < 0)
-		goto out_unlock;
+		goto out_pm_put;
 
 	iio_push_to_buffers_with_timestamp(indio_dev, data->buffer,
 					   data->timestamp);
 
+out_pm_put:
+	fxas21002c_pm_put(data);
+
 out_unlock:
 	mutex_unlock(&data->lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/hid-sensor-gyro-3d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/hid-sensor-gyro-3d.c
@@ -231,6 +231,7 @@
 		gyro_state->timestamp =
 			hid_sensor_convert_timestamp(&gyro_state->common_attributes,
 						     *(s64 *)raw_data);
+		ret = 0;
 	break;
 	default:
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/itg3200_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/itg3200_buffer.c
@@ -61,9 +61,9 @@
 
 	iio_push_to_buffers_with_timestamp(indio_dev, &scan, pf->timestamp);
 
+error_ret:
 	iio_trigger_notify_done(indio_dev->trig);
 
-error_ret:
 	return IRQ_HANDLED;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/mpu3050-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/mpu3050-core.c
@@ -876,6 +876,7 @@
 	ret = regmap_update_bits(mpu3050->map, MPU3050_PWR_MGM,
 				 MPU3050_PWR_MGM_SLEEP, 0);
 	if (ret) {
+		regulator_bulk_disable(ARRAY_SIZE(mpu3050->regs), mpu3050->regs);
 		dev_err(mpu3050->dev, "error setting power mode\n");
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/st_gyro_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/st_gyro_i2c.c
@@ -106,10 +106,10 @@
 {
 	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_gyro_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/gyro/st_gyro_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/gyro/st_gyro_spi.c
@@ -110,10 +110,10 @@
 {
 	struct iio_dev *indio_dev = spi_get_drvdata(spi);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_gyro_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/health/afe4403.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/health/afe4403.c
@@ -245,14 +245,14 @@
 			    int *val, int *val2, long mask)
 {
 	struct afe4403_data *afe = iio_priv(indio_dev);
-	unsigned int reg = afe4403_channel_values[chan->address];
-	unsigned int field = afe4403_channel_leds[chan->address];
+	unsigned int reg, field;
 	int ret;
 
 	switch (chan->type) {
 	case IIO_INTENSITY:
 		switch (mask) {
 		case IIO_CHAN_INFO_RAW:
+			reg = afe4403_channel_values[chan->address];
 			ret = afe4403_read(afe, reg, val);
 			if (ret)
 				return ret;
@@ -262,6 +262,7 @@
 	case IIO_CURRENT:
 		switch (mask) {
 		case IIO_CHAN_INFO_RAW:
+			field = afe4403_channel_leds[chan->address];
 			ret = regmap_field_read(afe->fields[field], val);
 			if (ret)
 				return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/health/afe4404.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/health/afe4404.c
@@ -250,20 +250,20 @@
 			    int *val, int *val2, long mask)
 {
 	struct afe4404_data *afe = iio_priv(indio_dev);
-	unsigned int value_reg = afe4404_channel_values[chan->address];
-	unsigned int led_field = afe4404_channel_leds[chan->address];
-	unsigned int offdac_field = afe4404_channel_offdacs[chan->address];
+	unsigned int value_reg, led_field, offdac_field;
 	int ret;
 
 	switch (chan->type) {
 	case IIO_INTENSITY:
 		switch (mask) {
 		case IIO_CHAN_INFO_RAW:
+			value_reg = afe4404_channel_values[chan->address];
 			ret = regmap_read(afe->regmap, value_reg, val);
 			if (ret)
 				return ret;
 			return IIO_VAL_INT;
 		case IIO_CHAN_INFO_OFFSET:
+			offdac_field = afe4404_channel_offdacs[chan->address];
 			ret = regmap_field_read(afe->fields[offdac_field], val);
 			if (ret)
 				return ret;
@@ -273,6 +273,7 @@
 	case IIO_CURRENT:
 		switch (mask) {
 		case IIO_CHAN_INFO_RAW:
+			led_field = afe4404_channel_leds[chan->address];
 			ret = regmap_field_read(afe->fields[led_field], val);
 			if (ret)
 				return ret;
@@ -295,19 +296,20 @@
 			     int val, int val2, long mask)
 {
 	struct afe4404_data *afe = iio_priv(indio_dev);
-	unsigned int led_field = afe4404_channel_leds[chan->address];
-	unsigned int offdac_field = afe4404_channel_offdacs[chan->address];
+	unsigned int led_field, offdac_field;
 
 	switch (chan->type) {
 	case IIO_INTENSITY:
 		switch (mask) {
 		case IIO_CHAN_INFO_OFFSET:
+			offdac_field = afe4404_channel_offdacs[chan->address];
 			return regmap_field_write(afe->fields[offdac_field], val);
 		}
 		break;
 	case IIO_CURRENT:
 		switch (mask) {
 		case IIO_CHAN_INFO_RAW:
+			led_field = afe4404_channel_leds[chan->address];
 			return regmap_field_write(afe->fields[led_field], val);
 		}
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/humidity/hts221_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/humidity/hts221_buffer.c
@@ -135,9 +135,12 @@
 
 	iio_trigger_set_drvdata(hw->trig, iio_dev);
 	hw->trig->ops = &hts221_trigger_ops;
+
+	err = devm_iio_trigger_register(hw->dev, hw->trig);
+
 	iio_dev->trig = iio_trigger_get(hw->trig);
 
-	return devm_iio_trigger_register(hw->dev, hw->trig);
+	return err;
 }
 
 static int hts221_buffer_preenable(struct iio_dev *iio_dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/Kconfig
@@ -47,6 +47,7 @@
 	depends on SPI
 	select IIO_ADIS_LIB
 	select IIO_ADIS_LIB_BUFFER if IIO_BUFFER
+	select CRC32
 	help
 	  Say yes here to build support for Analog Devices ADIS16375, ADIS16480,
 	  ADIS16485, ADIS16488 inertial sensors.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis.c
@@ -30,8 +30,8 @@
  * @value: The value to write to device (up to 4 bytes)
  * @size: The size of the @value (in bytes)
  */
-int __adis_write_reg(struct adis *adis, unsigned int reg,
-	unsigned int value, unsigned int size)
+int __adis_write_reg(struct adis *adis, unsigned int reg, unsigned int value,
+		     unsigned int size)
 {
 	unsigned int page = reg / ADIS_PAGE_SIZE;
 	int ret, i;
@@ -114,14 +114,14 @@
 	ret = spi_sync(adis->spi, &msg);
 	if (ret) {
 		dev_err(&adis->spi->dev, "Failed to write register 0x%02X: %d\n",
-				reg, ret);
+			reg, ret);
 	} else {
 		adis->current_page = page;
 	}
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(__adis_write_reg);
+EXPORT_SYMBOL_NS_GPL(__adis_write_reg, IIO_ADISLIB);
 
 /**
  * __adis_read_reg() - read N bytes from register (unlocked version)
@@ -130,8 +130,8 @@
  * @val: The value read back from the device
  * @size: The size of the @val buffer
  */
-int __adis_read_reg(struct adis *adis, unsigned int reg,
-	unsigned int *val, unsigned int size)
+int __adis_read_reg(struct adis *adis, unsigned int reg, unsigned int *val,
+		    unsigned int size)
 {
 	unsigned int page = reg / ADIS_PAGE_SIZE;
 	struct spi_message msg;
@@ -201,12 +201,12 @@
 	ret = spi_sync(adis->spi, &msg);
 	if (ret) {
 		dev_err(&adis->spi->dev, "Failed to read register 0x%02X: %d\n",
-				reg, ret);
+			reg, ret);
 		return ret;
-	} else {
-		adis->current_page = page;
 	}
 
+	adis->current_page = page;
+
 	switch (size) {
 	case 4:
 		*val = get_unaligned_be32(adis->rx);
@@ -218,7 +218,7 @@
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(__adis_read_reg);
+EXPORT_SYMBOL_NS_GPL(__adis_read_reg, IIO_ADISLIB);
 /**
  * __adis_update_bits_base() - ADIS Update bits function - Unlocked version
  * @adis: The adis device
@@ -243,17 +243,17 @@
 
 	return __adis_write_reg(adis, reg, __val, size);
 }
-EXPORT_SYMBOL_GPL(__adis_update_bits_base);
+EXPORT_SYMBOL_NS_GPL(__adis_update_bits_base, IIO_ADISLIB);
 
 #ifdef CONFIG_DEBUG_FS
 
-int adis_debugfs_reg_access(struct iio_dev *indio_dev,
-	unsigned int reg, unsigned int writeval, unsigned int *readval)
+int adis_debugfs_reg_access(struct iio_dev *indio_dev, unsigned int reg,
+			    unsigned int writeval, unsigned int *readval)
 {
 	struct adis *adis = iio_device_get_drvdata(indio_dev);
 
 	if (readval) {
-		uint16_t val16;
+		u16 val16;
 		int ret;
 
 		ret = adis_read_reg_16(adis, reg, &val16);
@@ -261,36 +261,41 @@
 			*readval = val16;
 
 		return ret;
-	} else {
-		return adis_write_reg_16(adis, reg, writeval);
 	}
+
+	return adis_write_reg_16(adis, reg, writeval);
 }
-EXPORT_SYMBOL(adis_debugfs_reg_access);
+EXPORT_SYMBOL_NS(adis_debugfs_reg_access, IIO_ADISLIB);
 
 #endif
 
 /**
- * adis_enable_irq() - Enable or disable data ready IRQ
+ * __adis_enable_irq() - Enable or disable data ready IRQ (unlocked)
  * @adis: The adis device
  * @enable: Whether to enable the IRQ
  *
  * Returns 0 on success, negative error code otherwise
  */
-int adis_enable_irq(struct adis *adis, bool enable)
+int __adis_enable_irq(struct adis *adis, bool enable)
 {
-	int ret = 0;
-	uint16_t msc;
+	int ret;
+	u16 msc;
 
-	mutex_lock(&adis->state_lock);
+	if (adis->data->enable_irq)
+		return adis->data->enable_irq(adis, enable);
+
+	if (adis->data->unmasked_drdy) {
+		if (enable)
+			enable_irq(adis->spi->irq);
+		else
+			disable_irq(adis->spi->irq);
 
-	if (adis->data->enable_irq) {
-		ret = adis->data->enable_irq(adis, enable);
-		goto out_unlock;
+		return 0;
 	}
 
 	ret = __adis_read_reg_16(adis, adis->data->msc_ctrl_reg, &msc);
 	if (ret)
-		goto out_unlock;
+		return ret;
 
 	msc |= ADIS_MSC_CTRL_DATA_RDY_POL_HIGH;
 	msc &= ~ADIS_MSC_CTRL_DATA_RDY_DIO2;
@@ -299,13 +304,9 @@
 	else
 		msc &= ~ADIS_MSC_CTRL_DATA_RDY_EN;
 
-	ret = __adis_write_reg_16(adis, adis->data->msc_ctrl_reg, msc);
-
-out_unlock:
-	mutex_unlock(&adis->state_lock);
-	return ret;
+	return __adis_write_reg_16(adis, adis->data->msc_ctrl_reg, msc);
 }
-EXPORT_SYMBOL(adis_enable_irq);
+EXPORT_SYMBOL_NS(__adis_enable_irq, IIO_ADISLIB);
 
 /**
  * __adis_check_status() - Check the device for error conditions (unlocked)
@@ -315,7 +316,7 @@
  */
 int __adis_check_status(struct adis *adis)
 {
-	uint16_t status;
+	u16 status;
 	int ret;
 	int i;
 
@@ -337,7 +338,7 @@
 
 	return -EIO;
 }
-EXPORT_SYMBOL_GPL(__adis_check_status);
+EXPORT_SYMBOL_NS_GPL(__adis_check_status, IIO_ADISLIB);
 
 /**
  * __adis_reset() - Reset the device (unlocked version)
@@ -351,7 +352,7 @@
 	const struct adis_timeout *timeouts = adis->data->timeouts;
 
 	ret = __adis_write_reg_8(adis, adis->data->glob_cmd_reg,
-			ADIS_GLOB_CMD_SW_RESET);
+				 ADIS_GLOB_CMD_SW_RESET);
 	if (ret) {
 		dev_err(&adis->spi->dev, "Failed to reset device: %d\n", ret);
 		return ret;
@@ -361,7 +362,7 @@
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(__adis_reset);
+EXPORT_SYMBOL_NS_GPL(__adis_reset, IIO_ADIS_LIB);
 
 static int adis_self_test(struct adis *adis)
 {
@@ -407,7 +408,7 @@
 {
 	const struct adis_timeout *timeouts = adis->data->timeouts;
 	struct gpio_desc *gpio;
-	uint16_t prod_id;
+	u16 prod_id;
 	int ret;
 
 	/* check if the device has rst pin low */
@@ -416,7 +417,7 @@
 		return PTR_ERR(gpio);
 
 	if (gpio) {
-		msleep(10);
+		usleep_range(10, 12);
 		/* bring device out of reset */
 		gpiod_set_value_cansleep(gpio, 0);
 		msleep(timeouts->reset_ms);
@@ -430,6 +431,14 @@
 	if (ret)
 		return ret;
 
+	/*
+	 * don't bother calling this if we can't unmask the IRQ as in this case
+	 * the IRQ is most likely not yet requested and we will request it
+	 * with 'IRQF_NO_AUTOEN' anyways.
+	 */
+	if (!adis->data->unmasked_drdy)
+		__adis_enable_irq(adis, false);
+
 	if (!adis->data->prod_id_reg)
 		return 0;
 
@@ -444,7 +453,7 @@
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(__adis_initial_startup);
+EXPORT_SYMBOL_NS_GPL(__adis_initial_startup, IIO_ADISLIB);
 
 /**
  * adis_single_conversion() - Performs a single sample conversion
@@ -462,7 +471,8 @@
  * a error bit in the channels raw value set error_mask to 0.
  */
 int adis_single_conversion(struct iio_dev *indio_dev,
-	const struct iio_chan_spec *chan, unsigned int error_mask, int *val)
+			   const struct iio_chan_spec *chan,
+			   unsigned int error_mask, int *val)
 {
 	struct adis *adis = iio_device_get_drvdata(indio_dev);
 	unsigned int uval;
@@ -471,7 +481,7 @@
 	mutex_lock(&adis->state_lock);
 
 	ret = __adis_read_reg(adis, chan->address, &uval,
-			chan->scan_type.storagebits / 8);
+			      chan->scan_type.storagebits / 8);
 	if (ret)
 		goto err_unlock;
 
@@ -491,7 +501,7 @@
 	mutex_unlock(&adis->state_lock);
 	return ret;
 }
-EXPORT_SYMBOL_GPL(adis_single_conversion);
+EXPORT_SYMBOL_NS_GPL(adis_single_conversion, IIO_ADISLIB);
 
 /**
  * adis_init() - Initialize adis device structure
@@ -506,7 +516,7 @@
  * called.
  */
 int adis_init(struct adis *adis, struct iio_dev *indio_dev,
-	struct spi_device *spi, const struct adis_data *data)
+	      struct spi_device *spi, const struct adis_data *data)
 {
 	if (!data || !data->timeouts) {
 		dev_err(&spi->dev, "No config data or timeouts not defined!\n");
@@ -526,9 +536,9 @@
 		adis->current_page = 0;
 	}
 
-	return adis_enable_irq(adis, false);
+	return 0;
 }
-EXPORT_SYMBOL_GPL(adis_init);
+EXPORT_SYMBOL_NS_GPL(adis_init, IIO_ADISLIB);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis16400.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis16400.c
@@ -1230,3 +1230,4 @@
 MODULE_AUTHOR("Manuel Stahl <manuel.stahl@iis.fraunhofer.de>");
 MODULE_DESCRIPTION("Analog Devices ADIS16400/5 IMU SPI driver");
 MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis16460.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis16460.c
@@ -444,3 +444,4 @@
 MODULE_AUTHOR("Dragos Bogdan <dragos.bogdan@analog.com>");
 MODULE_DESCRIPTION("Analog Devices ADIS16460 IMU driver");
 MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis16475.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis16475.c
@@ -1145,6 +1145,7 @@
 	struct device *dev = &st->adis.spi->dev;
 	const struct adis16475_sync *sync;
 	u32 sync_mode;
+	u16 val;
 
 	/* default to internal clk */
 	st->clk_freq = st->info->int_clk * 1000;
@@ -1214,8 +1215,9 @@
 	 * I'm keeping this for simplicity and avoiding extra variables
 	 * in chip_info.
 	 */
+	val = ADIS16475_SYNC_MODE(sync->sync_mode);
 	ret = __adis_update_bits(&st->adis, ADIS16475_REG_MSG_CTRL,
-				 ADIS16475_SYNC_MODE_MASK, sync->sync_mode);
+				 ADIS16475_SYNC_MODE_MASK, val);
 	if (ret)
 		return ret;
 
@@ -1273,50 +1275,6 @@
 	return 0;
 }
 
-static const struct of_device_id adis16475_of_match[] = {
-	{ .compatible = "adi,adis16470",
-		.data = &adis16475_chip_info[ADIS16470] },
-	{ .compatible = "adi,adis16475-1",
-		.data = &adis16475_chip_info[ADIS16475_1] },
-	{ .compatible = "adi,adis16475-2",
-		.data = &adis16475_chip_info[ADIS16475_2] },
-	{ .compatible = "adi,adis16475-3",
-		.data = &adis16475_chip_info[ADIS16475_3] },
-	{ .compatible = "adi,adis16477-1",
-		.data = &adis16475_chip_info[ADIS16477_1] },
-	{ .compatible = "adi,adis16477-2",
-		.data = &adis16475_chip_info[ADIS16477_2] },
-	{ .compatible = "adi,adis16477-3",
-		.data = &adis16475_chip_info[ADIS16477_3] },
-	{ .compatible = "adi,adis16465-1",
-		.data = &adis16475_chip_info[ADIS16465_1] },
-	{ .compatible = "adi,adis16465-2",
-		.data = &adis16475_chip_info[ADIS16465_2] },
-	{ .compatible = "adi,adis16465-3",
-		.data = &adis16475_chip_info[ADIS16465_3] },
-	{ .compatible = "adi,adis16467-1",
-		.data = &adis16475_chip_info[ADIS16467_1] },
-	{ .compatible = "adi,adis16467-2",
-		.data = &adis16475_chip_info[ADIS16467_2] },
-	{ .compatible = "adi,adis16467-3",
-		.data = &adis16475_chip_info[ADIS16467_3] },
-	{ .compatible = "adi,adis16500",
-		.data = &adis16475_chip_info[ADIS16500] },
-	{ .compatible = "adi,adis16505-1",
-		.data = &adis16475_chip_info[ADIS16505_1] },
-	{ .compatible = "adi,adis16505-2",
-		.data = &adis16475_chip_info[ADIS16505_2] },
-	{ .compatible = "adi,adis16505-3",
-		.data = &adis16475_chip_info[ADIS16505_3] },
-	{ .compatible = "adi,adis16507-1",
-		.data = &adis16475_chip_info[ADIS16507_1] },
-	{ .compatible = "adi,adis16507-2",
-		.data = &adis16475_chip_info[ADIS16507_2] },
-	{ .compatible = "adi,adis16507-3",
-		.data = &adis16475_chip_info[ADIS16507_3] },
-	{ },
-};
-MODULE_DEVICE_TABLE(of, adis16475_of_match);
 
 static int adis16475_probe(struct spi_device *spi)
 {
@@ -1330,7 +1288,7 @@
 
 	st = iio_priv(indio_dev);
 
-	st->info = device_get_match_data(&spi->dev);
+	st->info = spi_get_device_match_data(spi);
 	if (!st->info)
 		return -EINVAL;
 
@@ -1370,15 +1328,87 @@
 	return 0;
 }
 
+static const struct of_device_id adis16475_of_match[] = {
+	{ .compatible = "adi,adis16470",
+		.data = &adis16475_chip_info[ADIS16470] },
+	{ .compatible = "adi,adis16475-1",
+		.data = &adis16475_chip_info[ADIS16475_1] },
+	{ .compatible = "adi,adis16475-2",
+		.data = &adis16475_chip_info[ADIS16475_2] },
+	{ .compatible = "adi,adis16475-3",
+		.data = &adis16475_chip_info[ADIS16475_3] },
+	{ .compatible = "adi,adis16477-1",
+		.data = &adis16475_chip_info[ADIS16477_1] },
+	{ .compatible = "adi,adis16477-2",
+		.data = &adis16475_chip_info[ADIS16477_2] },
+	{ .compatible = "adi,adis16477-3",
+		.data = &adis16475_chip_info[ADIS16477_3] },
+	{ .compatible = "adi,adis16465-1",
+		.data = &adis16475_chip_info[ADIS16465_1] },
+	{ .compatible = "adi,adis16465-2",
+		.data = &adis16475_chip_info[ADIS16465_2] },
+	{ .compatible = "adi,adis16465-3",
+		.data = &adis16475_chip_info[ADIS16465_3] },
+	{ .compatible = "adi,adis16467-1",
+		.data = &adis16475_chip_info[ADIS16467_1] },
+	{ .compatible = "adi,adis16467-2",
+		.data = &adis16475_chip_info[ADIS16467_2] },
+	{ .compatible = "adi,adis16467-3",
+		.data = &adis16475_chip_info[ADIS16467_3] },
+	{ .compatible = "adi,adis16500",
+		.data = &adis16475_chip_info[ADIS16500] },
+	{ .compatible = "adi,adis16505-1",
+		.data = &adis16475_chip_info[ADIS16505_1] },
+	{ .compatible = "adi,adis16505-2",
+		.data = &adis16475_chip_info[ADIS16505_2] },
+	{ .compatible = "adi,adis16505-3",
+		.data = &adis16475_chip_info[ADIS16505_3] },
+	{ .compatible = "adi,adis16507-1",
+		.data = &adis16475_chip_info[ADIS16507_1] },
+	{ .compatible = "adi,adis16507-2",
+		.data = &adis16475_chip_info[ADIS16507_2] },
+	{ .compatible = "adi,adis16507-3",
+		.data = &adis16475_chip_info[ADIS16507_3] },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, adis16475_of_match);
+
+static const struct spi_device_id adis16475_ids[] = {
+	{ "adis16470", (kernel_ulong_t)&adis16475_chip_info[ADIS16470] },
+	{ "adis16475-1", (kernel_ulong_t)&adis16475_chip_info[ADIS16475_1] },
+	{ "adis16475-2", (kernel_ulong_t)&adis16475_chip_info[ADIS16475_2] },
+	{ "adis16475-3", (kernel_ulong_t)&adis16475_chip_info[ADIS16475_3] },
+	{ "adis16477-1", (kernel_ulong_t)&adis16475_chip_info[ADIS16477_1] },
+	{ "adis16477-2", (kernel_ulong_t)&adis16475_chip_info[ADIS16477_2] },
+	{ "adis16477-3", (kernel_ulong_t)&adis16475_chip_info[ADIS16477_3] },
+	{ "adis16465-1", (kernel_ulong_t)&adis16475_chip_info[ADIS16465_1] },
+	{ "adis16465-2", (kernel_ulong_t)&adis16475_chip_info[ADIS16465_2] },
+	{ "adis16465-3", (kernel_ulong_t)&adis16475_chip_info[ADIS16465_3] },
+	{ "adis16467-1", (kernel_ulong_t)&adis16475_chip_info[ADIS16467_1] },
+	{ "adis16467-2", (kernel_ulong_t)&adis16475_chip_info[ADIS16467_2] },
+	{ "adis16467-3", (kernel_ulong_t)&adis16475_chip_info[ADIS16467_3] },
+	{ "adis16500", (kernel_ulong_t)&adis16475_chip_info[ADIS16500] },
+	{ "adis16505-1", (kernel_ulong_t)&adis16475_chip_info[ADIS16505_1] },
+	{ "adis16505-2", (kernel_ulong_t)&adis16475_chip_info[ADIS16505_2] },
+	{ "adis16505-3", (kernel_ulong_t)&adis16475_chip_info[ADIS16505_3] },
+	{ "adis16507-1", (kernel_ulong_t)&adis16475_chip_info[ADIS16507_1] },
+	{ "adis16507-2", (kernel_ulong_t)&adis16475_chip_info[ADIS16507_2] },
+	{ "adis16507-3", (kernel_ulong_t)&adis16475_chip_info[ADIS16507_3] },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, adis16475_ids);
+
 static struct spi_driver adis16475_driver = {
 	.driver = {
 		.name = "adis16475",
 		.of_match_table = adis16475_of_match,
 	},
 	.probe = adis16475_probe,
+	.id_table = adis16475_ids,
 };
 module_spi_driver(adis16475_driver);
 
 MODULE_AUTHOR("Nuno Sa <nuno.sa@analog.com>");
 MODULE_DESCRIPTION("Analog Devices ADIS16475 IMU driver");
 MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis16480.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis16480.c
@@ -1403,6 +1403,7 @@
 {
 	const struct spi_device_id *id = spi_get_device_id(spi);
 	const struct adis_data *adis16480_data;
+	irq_handler_t trigger_handler = NULL;
 	struct iio_dev *indio_dev;
 	struct adis16480 *st;
 	int ret;
@@ -1474,8 +1475,12 @@
 		st->clk_freq = st->chip_info->int_clk;
 	}
 
+	/* Only use our trigger handler if burst mode is supported */
+	if (adis16480_data->burst_len)
+		trigger_handler = adis16480_trigger_handler;
+
 	ret = devm_adis_setup_buffer_and_trigger(&st->adis, indio_dev,
-						 adis16480_trigger_handler);
+						 trigger_handler);
 	if (ret)
 		return ret;
 
@@ -1533,3 +1538,4 @@
 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
 MODULE_DESCRIPTION("Analog Devices ADIS16480 IMU driver");
 MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis_buffer.c
@@ -20,7 +20,7 @@
 #include <linux/iio/imu/adis.h>
 
 static int adis_update_scan_mode_burst(struct iio_dev *indio_dev,
-	const unsigned long *scan_mask)
+				       const unsigned long *scan_mask)
 {
 	struct adis *adis = iio_device_get_drvdata(indio_dev);
 	unsigned int burst_length, burst_max_length;
@@ -67,7 +67,7 @@
 }
 
 int adis_update_scan_mode(struct iio_dev *indio_dev,
-	const unsigned long *scan_mask)
+			  const unsigned long *scan_mask)
 {
 	struct adis *adis = iio_device_get_drvdata(indio_dev);
 	const struct iio_chan_spec *chan;
@@ -124,7 +124,7 @@
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(adis_update_scan_mode);
+EXPORT_SYMBOL_NS_GPL(adis_update_scan_mode, IIO_ADISLIB);
 
 static irqreturn_t adis_trigger_handler(int irq, void *p)
 {
@@ -158,7 +158,7 @@
 	}
 
 	iio_push_to_buffers_with_timestamp(indio_dev, adis->buffer,
-		pf->timestamp);
+					   pf->timestamp);
 
 irq_done:
 	iio_trigger_notify_done(indio_dev->trig);
@@ -212,5 +212,5 @@
 	return devm_add_action_or_reset(&adis->spi->dev, adis_buffer_cleanup,
 					adis);
 }
-EXPORT_SYMBOL_GPL(devm_adis_setup_buffer_and_trigger);
+EXPORT_SYMBOL_NS_GPL(devm_adis_setup_buffer_and_trigger, IIO_ADISLIB);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/adis_trigger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/adis_trigger.c
@@ -15,8 +15,7 @@
 #include <linux/iio/trigger.h>
 #include <linux/iio/imu/adis.h>
 
-static int adis_data_rdy_trigger_set_state(struct iio_trigger *trig,
-						bool state)
+static int adis_data_rdy_trigger_set_state(struct iio_trigger *trig, bool state)
 {
 	struct adis *adis = iio_trigger_get_drvdata(trig);
 
@@ -30,6 +29,10 @@
 static int adis_validate_irq_flag(struct adis *adis)
 {
 	unsigned long direction = adis->irq_flag & IRQF_TRIGGER_MASK;
+
+	/* We cannot mask the interrupt so ensure it's not enabled at request */
+	if (adis->data->unmasked_drdy)
+		adis->irq_flag |= IRQF_NO_AUTOEN;
 	/*
 	 * Typically this devices have data ready either on the rising edge or
 	 * on the falling edge of the data ready pin. This checks enforces that
@@ -84,5 +87,5 @@
 
 	return devm_iio_trigger_register(&adis->spi->dev, adis->trig);
 }
-EXPORT_SYMBOL_GPL(devm_adis_probe_trigger);
+EXPORT_SYMBOL_NS_GPL(devm_adis_probe_trigger, IIO_ADISLIB);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/bmi160/bmi160_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/bmi160/bmi160_core.c
@@ -730,7 +730,7 @@
 
 	ret = regmap_write(data->regmap, BMI160_REG_CMD, BMI160_CMD_SOFTRESET);
 	if (ret)
-		return ret;
+		goto disable_regulator;
 
 	usleep_range(BMI160_SOFTRESET_USLEEP, BMI160_SOFTRESET_USLEEP + 1);
 
@@ -741,29 +741,37 @@
 	if (use_spi) {
 		ret = regmap_read(data->regmap, BMI160_REG_DUMMY, &val);
 		if (ret)
-			return ret;
+			goto disable_regulator;
 	}
 
 	ret = regmap_read(data->regmap, BMI160_REG_CHIP_ID, &val);
 	if (ret) {
 		dev_err(dev, "Error reading chip id\n");
-		return ret;
+		goto disable_regulator;
 	}
 	if (val != BMI160_CHIP_ID_VAL) {
 		dev_err(dev, "Wrong chip id, got %x expected %x\n",
 			val, BMI160_CHIP_ID_VAL);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto disable_regulator;
 	}
 
 	ret = bmi160_set_mode(data, BMI160_ACCEL, true);
 	if (ret)
-		return ret;
+		goto disable_regulator;
 
 	ret = bmi160_set_mode(data, BMI160_GYRO, true);
 	if (ret)
-		return ret;
+		goto disable_accel;
 
 	return 0;
+
+disable_accel:
+	bmi160_set_mode(data, BMI160_ACCEL, false);
+
+disable_regulator:
+	regulator_bulk_disable(ARRAY_SIZE(data->supplies), data->supplies);
+	return ret;
 }
 
 static int bmi160_data_rdy_trigger_set_state(struct iio_trigger *trig,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/fxos8700_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/fxos8700_core.c
@@ -10,6 +10,7 @@
 #include <linux/regmap.h>
 #include <linux/acpi.h>
 #include <linux/bitops.h>
+#include <linux/bitfield.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/sysfs.h>
@@ -144,9 +145,8 @@
 #define FXOS8700_NVM_DATA_BNK0      0xa7
 
 /* Bit definitions for FXOS8700_CTRL_REG1 */
-#define FXOS8700_CTRL_ODR_MSK       0x38
 #define FXOS8700_CTRL_ODR_MAX       0x00
-#define FXOS8700_CTRL_ODR_MIN       GENMASK(4, 3)
+#define FXOS8700_CTRL_ODR_MSK       GENMASK(5, 3)
 
 /* Bit definitions for FXOS8700_M_CTRL_REG1 */
 #define FXOS8700_HMS_MASK           GENMASK(1, 0)
@@ -320,7 +320,7 @@
 	switch (iio_type) {
 	case IIO_ACCEL:
 		return FXOS8700_ACCEL;
-	case IIO_ANGL_VEL:
+	case IIO_MAGN:
 		return FXOS8700_MAGN;
 	default:
 		return -EINVAL;
@@ -345,15 +345,35 @@
 static int fxos8700_set_scale(struct fxos8700_data *data,
 			      enum fxos8700_sensor t, int uscale)
 {
-	int i;
+	int i, ret, val;
+	bool active_mode;
 	static const int scale_num = ARRAY_SIZE(fxos8700_accel_scale);
 	struct device *dev = regmap_get_device(data->regmap);
 
 	if (t == FXOS8700_MAGN) {
-		dev_err(dev, "Magnetometer scale is locked at 1200uT\n");
+		dev_err(dev, "Magnetometer scale is locked at 0.001Gs\n");
 		return -EINVAL;
 	}
 
+	/*
+	 * When device is in active mode, it failed to set an ACCEL
+	 * full-scale range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG.
+	 * This is not align with the datasheet, but it is a fxos8700
+	 * chip behavier. Set the device in standby mode before setting
+	 * an ACCEL full-scale range.
+	 */
+	ret = regmap_read(data->regmap, FXOS8700_CTRL_REG1, &val);
+	if (ret)
+		return ret;
+
+	active_mode = val & FXOS8700_ACTIVE;
+	if (active_mode) {
+		ret = regmap_write(data->regmap, FXOS8700_CTRL_REG1,
+				   val & ~FXOS8700_ACTIVE);
+		if (ret)
+			return ret;
+	}
+
 	for (i = 0; i < scale_num; i++)
 		if (fxos8700_accel_scale[i].uscale == uscale)
 			break;
@@ -361,8 +381,12 @@
 	if (i == scale_num)
 		return -EINVAL;
 
-	return regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG,
+	ret = regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG,
 			    fxos8700_accel_scale[i].bits);
+	if (ret)
+		return ret;
+	return regmap_write(data->regmap, FXOS8700_CTRL_REG1,
+				  active_mode);
 }
 
 static int fxos8700_get_scale(struct fxos8700_data *data,
@@ -372,7 +396,7 @@
 	static const int scale_num = ARRAY_SIZE(fxos8700_accel_scale);
 
 	if (t == FXOS8700_MAGN) {
-		*uscale = 1200; /* Magnetometer is locked at 1200uT */
+		*uscale = 1000; /* Magnetometer is locked at 0.001Gs */
 		return 0;
 	}
 
@@ -394,22 +418,61 @@
 			     int axis, int *val)
 {
 	u8 base, reg;
+	s16 tmp;
 	int ret;
-	enum fxos8700_sensor type = fxos8700_to_sensor(chan_type);
 
-	base = type ? FXOS8700_OUT_X_MSB : FXOS8700_M_OUT_X_MSB;
+	/*
+	 * Different register base addresses varies with channel types.
+	 * This bug hasn't been noticed before because using an enum is
+	 * really hard to read. Use an a switch statement to take over that.
+	 */
+	switch (chan_type) {
+	case IIO_ACCEL:
+		base = FXOS8700_OUT_X_MSB;
+		break;
+	case IIO_MAGN:
+		base = FXOS8700_M_OUT_X_MSB;
+		break;
+	default:
+		return -EINVAL;
+	}
 
 	/* Block read 6 bytes of device output registers to avoid data loss */
 	ret = regmap_bulk_read(data->regmap, base, data->buf,
-			       FXOS8700_DATA_BUF_SIZE);
+			       sizeof(data->buf));
 	if (ret)
 		return ret;
 
 	/* Convert axis to buffer index */
 	reg = axis - IIO_MOD_X;
 
+	/*
+	 * Convert to native endianness. The accel data and magn data
+	 * are signed, so a forced type conversion is needed.
+	 */
+	tmp = be16_to_cpu(data->buf[reg]);
+
+	/*
+	 * ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
+	 * 14-bit left-justified sample data and MAGN output data registers
+	 * contain the X-axis, Y-axis, and Z-axis 16-bit sample data. Apply
+	 * a signed 2 bits right shift to the readback raw data from ACCEL
+	 * output data register and keep that from MAGN sensor as the origin.
+	 * Value should be extended to 32 bit.
+	 */
+	switch (chan_type) {
+	case IIO_ACCEL:
+		tmp = tmp >> 2;
+		break;
+	case IIO_MAGN:
+		/* Nothing to do */
+		break;
+	default:
+		return -EINVAL;
+	}
+
 	/* Convert to native endianness */
-	*val = sign_extend32(be16_to_cpu(data->buf[reg]), 15);
+	*val = sign_extend32(tmp, 15);
 
 	return 0;
 }
@@ -445,10 +508,9 @@
 	if (i >= odr_num)
 		return -EINVAL;
 
-	return regmap_update_bits(data->regmap,
-				  FXOS8700_CTRL_REG1,
-				  FXOS8700_CTRL_ODR_MSK + FXOS8700_ACTIVE,
-				  fxos8700_odr[i].bits << 3 | active_mode);
+	val &= ~FXOS8700_CTRL_ODR_MSK;
+	val |= FIELD_PREP(FXOS8700_CTRL_ODR_MSK, fxos8700_odr[i].bits) | FXOS8700_ACTIVE;
+	return regmap_write(data->regmap, FXOS8700_CTRL_REG1, val);
 }
 
 static int fxos8700_get_odr(struct fxos8700_data *data, enum fxos8700_sensor t,
@@ -461,7 +523,7 @@
 	if (ret)
 		return ret;
 
-	val &= FXOS8700_CTRL_ODR_MSK;
+	val = FIELD_GET(FXOS8700_CTRL_ODR_MSK, val);
 
 	for (i = 0; i < odr_num; i++)
 		if (val == fxos8700_odr[i].bits)
@@ -526,7 +588,7 @@
 static IIO_CONST_ATTR(in_magn_sampling_frequency_available,
 		      "1.5625 6.25 12.5 50 100 200 400 800");
 static IIO_CONST_ATTR(in_accel_scale_available, "0.000244 0.000488 0.000976");
-static IIO_CONST_ATTR(in_magn_scale_available, "0.000001200");
+static IIO_CONST_ATTR(in_magn_scale_available, "0.001000");
 
 static struct attribute *fxos8700_attrs[] = {
 	&iio_const_attr_in_accel_sampling_frequency_available.dev_attr.attr,
@@ -592,14 +654,19 @@
 	if (ret)
 		return ret;
 
-	/* Max ODR (800Hz individual or 400Hz hybrid), active mode */
-	ret = regmap_write(data->regmap, FXOS8700_CTRL_REG1,
-			   FXOS8700_CTRL_ODR_MAX | FXOS8700_ACTIVE);
+	/*
+	 * Set max full-scale range (+/-8G) for ACCEL sensor in chip
+	 * initialization then activate the device.
+	 */
+	ret = regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG, MODE_8G);
 	if (ret)
 		return ret;
 
-	/* Set for max full-scale range (+/-8G) */
-	return regmap_write(data->regmap, FXOS8700_XYZ_DATA_CFG, MODE_8G);
+	/* Max ODR (800Hz individual or 400Hz hybrid), active mode */
+	return regmap_update_bits(data->regmap, FXOS8700_CTRL_REG1,
+				FXOS8700_CTRL_ODR_MSK | FXOS8700_ACTIVE,
+				FIELD_PREP(FXOS8700_CTRL_ODR_MSK, FXOS8700_CTRL_ODR_MAX) |
+				FXOS8700_ACTIVE);
 }
 
 static void fxos8700_chip_uninit(void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600.h
@@ -17,6 +17,7 @@
 #include "inv_icm42600_buffer.h"
 
 enum inv_icm42600_chip {
+	INV_CHIP_INVALID,
 	INV_CHIP_ICM42600,
 	INV_CHIP_ICM42602,
 	INV_CHIP_ICM42605,
@@ -359,6 +360,7 @@
 typedef int (*inv_icm42600_bus_setup)(struct inv_icm42600_state *);
 
 extern const struct regmap_config inv_icm42600_regmap_config;
+extern const struct regmap_config inv_icm42600_spi_regmap_config;
 extern const struct dev_pm_ops inv_icm42600_pm_ops;
 
 const struct iio_mount_matrix *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600_accel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600_accel.c
@@ -128,10 +128,6 @@
 	/* update data FIFO write */
 	inv_icm42600_timestamp_apply_odr(ts, 0, 0, 0);
 	ret = inv_icm42600_buffer_set_fifo_en(st, fifo_en | st->fifo.en);
-	if (ret)
-		goto out_unlock;
-
-	ret = inv_icm42600_buffer_update_watermark(st);
 
 out_unlock:
 	mutex_unlock(&st->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600_buffer.c
@@ -275,9 +275,14 @@
 {
 	struct inv_icm42600_state *st = iio_device_get_drvdata(indio_dev);
 	struct device *dev = regmap_get_device(st->map);
+	struct inv_icm42600_timestamp *ts = iio_priv(indio_dev);
 
 	pm_runtime_get_sync(dev);
 
+	mutex_lock(&st->lock);
+	inv_icm42600_timestamp_reset(ts);
+	mutex_unlock(&st->lock);
+
 	return 0;
 }
 
@@ -375,7 +380,6 @@
 	struct device *dev = regmap_get_device(st->map);
 	unsigned int sensor;
 	unsigned int *watermark;
-	struct inv_icm42600_timestamp *ts;
 	struct inv_icm42600_sensor_conf conf = INV_ICM42600_SENSOR_CONF_INIT;
 	unsigned int sleep_temp = 0;
 	unsigned int sleep_sensor = 0;
@@ -385,11 +389,9 @@
 	if (indio_dev == st->indio_gyro) {
 		sensor = INV_ICM42600_SENSOR_GYRO;
 		watermark = &st->fifo.watermark.gyro;
-		ts = iio_priv(st->indio_gyro);
 	} else if (indio_dev == st->indio_accel) {
 		sensor = INV_ICM42600_SENSOR_ACCEL;
 		watermark = &st->fifo.watermark.accel;
-		ts = iio_priv(st->indio_accel);
 	} else {
 		return -EINVAL;
 	}
@@ -417,8 +419,6 @@
 	if (!st->fifo.on)
 		ret = inv_icm42600_set_temp_conf(st, false, &sleep_temp);
 
-	inv_icm42600_timestamp_reset(ts);
-
 out_unlock:
 	mutex_unlock(&st->lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600_core.c
@@ -43,6 +43,17 @@
 };
 EXPORT_SYMBOL_GPL(inv_icm42600_regmap_config);
 
+/* define specific regmap for SPI not supporting burst write */
+const struct regmap_config inv_icm42600_spi_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = 0x4FFF,
+	.ranges = inv_icm42600_regmap_ranges,
+	.num_ranges = ARRAY_SIZE(inv_icm42600_regmap_ranges),
+	.use_single_write = true,
+};
+EXPORT_SYMBOL_GPL(inv_icm42600_spi_regmap_config);
+
 struct inv_icm42600_hw {
 	uint8_t whoami;
 	const char *name;
@@ -565,7 +576,7 @@
 	bool open_drain;
 	int ret;
 
-	if (chip < 0 || chip >= INV_CHIP_NB) {
+	if (chip <= INV_CHIP_INVALID || chip >= INV_CHIP_NB) {
 		dev_err(dev, "invalid chip = %d\n", chip);
 		return -ENODEV;
 	}
@@ -709,6 +720,8 @@
 static int __maybe_unused inv_icm42600_resume(struct device *dev)
 {
 	struct inv_icm42600_state *st = dev_get_drvdata(dev);
+	struct inv_icm42600_timestamp *gyro_ts = iio_priv(st->indio_gyro);
+	struct inv_icm42600_timestamp *accel_ts = iio_priv(st->indio_accel);
 	int ret;
 
 	mutex_lock(&st->lock);
@@ -729,9 +742,12 @@
 		goto out_unlock;
 
 	/* restore FIFO data streaming */
-	if (st->fifo.on)
+	if (st->fifo.on) {
+		inv_icm42600_timestamp_reset(gyro_ts);
+		inv_icm42600_timestamp_reset(accel_ts);
 		ret = regmap_write(st->map, INV_ICM42600_REG_FIFO_CONFIG,
 				   INV_ICM42600_FIFO_CONFIG_STREAM);
+	}
 
 out_unlock:
 	mutex_unlock(&st->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600_gyro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600_gyro.c
@@ -128,10 +128,6 @@
 	/* update data FIFO write */
 	inv_icm42600_timestamp_apply_odr(ts, 0, 0, 0);
 	ret = inv_icm42600_buffer_set_fifo_en(st, fifo_en | st->fifo.en);
-	if (ret)
-		goto out_unlock;
-
-	ret = inv_icm42600_buffer_update_watermark(st);
 
 out_unlock:
 	mutex_unlock(&st->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600_i2c.c
@@ -18,12 +18,15 @@
 	unsigned int mask, val;
 	int ret;
 
-	/* setup interface registers */
-	ret = regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG6,
-				 INV_ICM42600_INTF_CONFIG6_MASK,
-				 INV_ICM42600_INTF_CONFIG6_I3C_EN);
-	if (ret)
-		return ret;
+	/*
+	 * setup interface registers
+	 * This register write to REG_INTF_CONFIG6 enables a spike filter that
+	 * is impacting the line and can prevent the I2C ACK to be seen by the
+	 * controller. So we don't test the return value.
+	 */
+	regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG6,
+			   INV_ICM42600_INTF_CONFIG6_MASK,
+			   INV_ICM42600_INTF_CONFIG6_I3C_EN);
 
 	ret = regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG4,
 				 INV_ICM42600_INTF_CONFIG4_I3C_BUS_ONLY, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_icm42600/inv_icm42600_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_icm42600/inv_icm42600_spi.c
@@ -59,7 +59,8 @@
 		return -EINVAL;
 	chip = (enum inv_icm42600_chip)match;
 
-	regmap = devm_regmap_init_spi(spi, &inv_icm42600_regmap_config);
+	/* use SPI specific regmap */
+	regmap = devm_regmap_init_spi(spi, &inv_icm42600_spi_regmap_config);
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -727,13 +727,13 @@
 			ret = inv_mpu6050_sensor_show(st, st->reg->gyro_offset,
 						chan->channel2, val);
 			mutex_unlock(&st->lock);
-			return IIO_VAL_INT;
+			return ret;
 		case IIO_ACCEL:
 			mutex_lock(&st->lock);
 			ret = inv_mpu6050_sensor_show(st, st->reg->accl_offset,
 						chan->channel2, val);
 			mutex_unlock(&st->lock);
-			return IIO_VAL_INT;
+			return ret;
 
 		default:
 			return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c
@@ -261,6 +261,7 @@
  */
 int inv_mpu_magn_set_orient(struct inv_mpu6050_state *st)
 {
+	struct device *dev = regmap_get_device(st->map);
 	const char *orient;
 	char *str;
 	int i;
@@ -279,22 +280,27 @@
 		st->magn_orient.rotation[4] = st->orientation.rotation[1];
 		st->magn_orient.rotation[5] = st->orientation.rotation[2];
 		/* z <- -z */
-		for (i = 0; i < 3; ++i) {
-			orient = st->orientation.rotation[6 + i];
-			/* use length + 2 for adding minus sign if needed */
-			str = devm_kzalloc(regmap_get_device(st->map),
-					   strlen(orient) + 2, GFP_KERNEL);
-			if (str == NULL)
+		for (i = 6; i < 9; ++i) {
+			orient = st->orientation.rotation[i];
+
+			/*
+			 * The value is negated according to one of the following
+			 * rules:
+			 *
+			 * 1) Drop leading minus.
+			 * 2) Leave 0 as is.
+			 * 3) Add leading minus.
+			 */
+			if (orient[0] == '-')
+				str = devm_kstrdup(dev, orient + 1, GFP_KERNEL);
+			else if (!strcmp(orient, "0"))
+				str = devm_kstrdup(dev, orient, GFP_KERNEL);
+			else
+				str = devm_kasprintf(dev, GFP_KERNEL, "-%s", orient);
+			if (!str)
 				return -ENOMEM;
-			if (strcmp(orient, "0") == 0) {
-				strcpy(str, orient);
-			} else if (orient[0] == '-') {
-				strcpy(str, &orient[1]);
-			} else {
-				str[0] = '-';
-				strcpy(&str[1], orient);
-			}
-			st->magn_orient.rotation[6 + i] = str;
+
+			st->magn_orient.rotation[i] = str;
 		}
 		break;
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/kmx61.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/kmx61.c
@@ -1192,7 +1192,7 @@
 	struct kmx61_data *data = kmx61_get_data(indio_dev);
 	int bit, ret, i = 0;
 	u8 base;
-	s16 buffer[8];
+	s16 buffer[8] = { };
 
 	if (indio_dev == data->acc_indio_dev)
 		base = KMX61_ACC_XOUT_L;
@@ -1385,7 +1385,7 @@
 	ret = iio_device_register(data->acc_indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "Failed to register acc iio device\n");
-		goto err_buffer_cleanup_mag;
+		goto err_pm_cleanup;
 	}
 
 	ret = iio_device_register(data->mag_indio_dev);
@@ -1398,6 +1398,9 @@
 
 err_iio_unregister_acc:
 	iio_device_unregister(data->acc_indio_dev);
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 err_buffer_cleanup_mag:
 	if (client->irq > 0)
 		iio_triggered_buffer_cleanup(data->mag_indio_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
@@ -1279,6 +1279,8 @@
 	int err;
 
 	switch (sensor->id) {
+	case ST_LSM6DSX_ID_GYRO:
+		break;
 	case ST_LSM6DSX_ID_EXT0:
 	case ST_LSM6DSX_ID_EXT1:
 	case ST_LSM6DSX_ID_EXT2:
@@ -1304,8 +1306,8 @@
 		}
 		break;
 	}
-	default:
-		break;
+	default: /* should never occur */
+		return -EINVAL;
 	}
 
 	if (req_odr > 0) {
@@ -1370,8 +1372,12 @@
 	if (err < 0)
 		return err;
 
+	/*
+	 * we need to wait for sensor settling time before
+	 * reading data in order to avoid corrupted samples
+	 */
 	delay = 1000000000 / sensor->odr;
-	usleep_range(delay, 2 * delay);
+	usleep_range(3 * delay, 4 * delay);
 
 	err = st_lsm6dsx_read_locked(hw, addr, &data, sizeof(data));
 	if (err < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/industrialio-buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/industrialio-buffer.c
@@ -1312,6 +1312,11 @@
 	iio_attr->buffer = buffer;
 	memcpy(&iio_attr->dev_attr, dattr, sizeof(iio_attr->dev_attr));
 	iio_attr->dev_attr.attr.name = kstrdup_const(attr->name, GFP_KERNEL);
+	if (!iio_attr->dev_attr.attr.name) {
+		kfree(iio_attr);
+		return NULL;
+	}
+
 	sysfs_attr_init(&iio_attr->dev_attr.attr);
 
 	list_add(&iio_attr->l, &buffer->buffer_attr_list);
@@ -1362,10 +1367,10 @@
 
 	return 0;
 
-error_free_buffer_attrs:
-	kfree(iio_dev_opaque->legacy_buffer_group.attrs);
 error_free_scan_el_attrs:
 	kfree(iio_dev_opaque->legacy_scan_el_group.attrs);
+error_free_buffer_attrs:
+	kfree(iio_dev_opaque->legacy_buffer_group.attrs);
 
 	return ret;
 }
@@ -1441,9 +1446,17 @@
 	}
 
 	if (copy_to_user(ival, &fd, sizeof(fd))) {
-		put_unused_fd(fd);
-		ret = -EFAULT;
-		goto error_free_ib;
+		/*
+		 * "Leak" the fd, as there's not much we can do about this
+		 * anyway. 'fd' might have been closed already, as
+		 * anon_inode_getfd() called fd_install() on it, which made
+		 * it reachable by userland.
+		 *
+		 * Instead of allowing a malicious user to play tricks with
+		 * us, rely on the process exit path to do any necessary
+		 * cleanup, as in releasing the file, if still needed.
+		 */
+		return -EFAULT;
 	}
 
 	return 0;
@@ -1531,6 +1544,7 @@
 		       sizeof(struct attribute *) * buffer_attrcount);
 
 	buffer_attrcount += ARRAY_SIZE(iio_buffer_attrs);
+	buffer->buffer_group.attrs = attr;
 
 	for (i = 0; i < buffer_attrcount; i++) {
 		struct attribute *wrapped;
@@ -1538,7 +1552,7 @@
 		wrapped = iio_buffer_wrap_attr(buffer, attr[i]);
 		if (!wrapped) {
 			ret = -ENOMEM;
-			goto error_free_scan_mask;
+			goto error_free_buffer_attrs;
 		}
 		attr[i] = wrapped;
 	}
@@ -1553,8 +1567,6 @@
 		goto error_free_buffer_attrs;
 	}
 
-	buffer->buffer_group.attrs = attr;
-
 	ret = iio_device_register_sysfs_group(indio_dev, &buffer->buffer_group);
 	if (ret)
 		goto error_free_buffer_attr_group_name;
@@ -1583,8 +1595,12 @@
 	return ret;
 }
 
-static void __iio_buffer_free_sysfs_and_mask(struct iio_buffer *buffer)
+static void __iio_buffer_free_sysfs_and_mask(struct iio_buffer *buffer,
+					     struct iio_dev *indio_dev,
+					     int index)
 {
+	if (index == 0)
+		iio_buffer_unregister_legacy_sysfs_groups(indio_dev);
 	bitmap_free(buffer->scan_mask);
 	kfree(buffer->buffer_group.name);
 	kfree(buffer->buffer_group.attrs);
@@ -1616,7 +1632,7 @@
 		buffer = iio_dev_opaque->attached_buffers[i];
 		ret = __iio_buffer_alloc_sysfs_and_mask(buffer, indio_dev, i);
 		if (ret) {
-			unwind_idx = i;
+			unwind_idx = i - 1;
 			goto error_unwind_sysfs_and_mask;
 		}
 	}
@@ -1638,7 +1654,7 @@
 error_unwind_sysfs_and_mask:
 	for (; unwind_idx >= 0; unwind_idx--) {
 		buffer = iio_dev_opaque->attached_buffers[unwind_idx];
-		__iio_buffer_free_sysfs_and_mask(buffer);
+		__iio_buffer_free_sysfs_and_mask(buffer, indio_dev, unwind_idx);
 	}
 	return ret;
 }
@@ -1655,11 +1671,9 @@
 	iio_device_ioctl_handler_unregister(iio_dev_opaque->buffer_ioctl_handler);
 	kfree(iio_dev_opaque->buffer_ioctl_handler);
 
-	iio_buffer_unregister_legacy_sysfs_groups(indio_dev);
-
 	for (i = iio_dev_opaque->attached_buffers_cnt - 1; i >= 0; i--) {
 		buffer = iio_dev_opaque->attached_buffers[i];
-		__iio_buffer_free_sysfs_and_mask(buffer);
+		__iio_buffer_free_sysfs_and_mask(buffer, indio_dev, i);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/industrialio-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/industrialio-core.c
@@ -185,6 +185,18 @@
 EXPORT_SYMBOL_GPL(iio_device_id);
 
 /**
+ * iio_buffer_enabled() - helper function to test if the buffer is enabled
+ * @indio_dev:		IIO device structure for device
+ */
+bool iio_buffer_enabled(struct iio_dev *indio_dev)
+{
+	return indio_dev->currentmode
+		& (INDIO_BUFFER_TRIGGERED | INDIO_BUFFER_HARDWARE |
+		   INDIO_BUFFER_SOFTWARE);
+}
+EXPORT_SYMBOL_GPL(iio_buffer_enabled);
+
+/**
  * iio_sysfs_match_string_with_gaps - matches given string in an array with gaps
  * @array: array of strings
  * @n: number of strings in the array
@@ -818,7 +830,23 @@
 
 static ssize_t iio_format_avail_range(char *buf, const int *vals, int type)
 {
-	return iio_format_list(buf, vals, type, 3, "[", "]");
+	int length;
+
+	/*
+	 * length refers to the array size , not the number of elements.
+	 * The purpose is to print the range [min , step ,max] so length should
+	 * be 3 in case of int, and 6 for other types.
+	 */
+	switch (type) {
+	case IIO_VAL_INT:
+		length = 3;
+		break;
+	default:
+		length = 6;
+		break;
+	}
+
+	return iio_format_list(buf, vals, type, length, "[", "]");
 }
 
 static ssize_t iio_read_channel_info_avail(struct device *dev,
@@ -1582,10 +1610,13 @@
 	ret = iio_device_register_sysfs_group(indio_dev,
 					      &iio_dev_opaque->chan_attr_group);
 	if (ret)
-		goto error_clear_attrs;
+		goto error_free_chan_attrs;
 
 	return 0;
 
+error_free_chan_attrs:
+	kfree(iio_dev_opaque->chan_attr_group.attrs);
+	iio_dev_opaque->chan_attr_group.attrs = NULL;
 error_clear_attrs:
 	iio_free_chan_devattr_list(&iio_dev_opaque->channel_attr_list);
 
@@ -1600,6 +1631,7 @@
 	kfree(iio_dev_opaque->chan_attr_group.attrs);
 	iio_dev_opaque->chan_attr_group.attrs = NULL;
 	kfree(iio_dev_opaque->groups);
+	iio_dev_opaque->groups = NULL;
 }
 
 static void iio_dev_release(struct device *device)
@@ -1664,7 +1696,13 @@
 		kfree(iio_dev_opaque);
 		return NULL;
 	}
-	dev_set_name(&indio_dev->dev, "iio:device%d", iio_dev_opaque->id);
+
+	if (dev_set_name(&indio_dev->dev, "iio:device%d", iio_dev_opaque->id)) {
+		ida_simple_remove(&iio_ida, iio_dev_opaque->id);
+		kfree(iio_dev_opaque);
+		return NULL;
+	}
+
 	INIT_LIST_HEAD(&iio_dev_opaque->buffer_list);
 	INIT_LIST_HEAD(&iio_dev_opaque->ioctl_handlers);
 
@@ -2049,6 +2087,55 @@
 }
 EXPORT_SYMBOL_GPL(iio_device_release_direct_mode);
 
+/**
+ * iio_device_claim_buffer_mode - Keep device in buffer mode
+ * @indio_dev:	the iio_dev associated with the device
+ *
+ * If the device is in buffer mode it is guaranteed to stay
+ * that way until iio_device_release_buffer_mode() is called.
+ *
+ * Use with iio_device_release_buffer_mode().
+ *
+ * Returns: 0 on success, -EBUSY on failure.
+ */
+int iio_device_claim_buffer_mode(struct iio_dev *indio_dev)
+{
+	mutex_lock(&indio_dev->mlock);
+
+	if (iio_buffer_enabled(indio_dev))
+		return 0;
+
+	mutex_unlock(&indio_dev->mlock);
+	return -EBUSY;
+}
+EXPORT_SYMBOL_GPL(iio_device_claim_buffer_mode);
+
+/**
+ * iio_device_release_buffer_mode - releases claim on buffer mode
+ * @indio_dev:	the iio_dev associated with the device
+ *
+ * Release the claim. Device is no longer guaranteed to stay
+ * in buffer mode.
+ *
+ * Use with iio_device_claim_buffer_mode().
+ */
+void iio_device_release_buffer_mode(struct iio_dev *indio_dev)
+{
+	mutex_unlock(&indio_dev->mlock);
+}
+EXPORT_SYMBOL_GPL(iio_device_release_buffer_mode);
+
+/**
+ * iio_device_get_current_mode() - helper function providing read-only access to
+ *				   the @currentmode variable
+ * @indio_dev:			   IIO device structure for device
+ */
+int iio_device_get_current_mode(struct iio_dev *indio_dev)
+{
+	return indio_dev->currentmode;
+}
+EXPORT_SYMBOL_GPL(iio_device_get_current_mode);
+
 subsys_initcall(iio_init);
 module_exit(iio_exit);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/industrialio-event.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/industrialio-event.c
@@ -549,7 +549,7 @@
 
 	ret = iio_device_register_sysfs_group(indio_dev, &ev_int->group);
 	if (ret)
-		goto error_free_setup_event_lines;
+		goto error_free_group_attrs;
 
 	ev_int->ioctl_handler.ioctl = iio_event_ioctl;
 	iio_device_ioctl_handler_register(&iio_dev_opaque->indio_dev,
@@ -557,6 +557,8 @@
 
 	return 0;
 
+error_free_group_attrs:
+	kfree(ev_int->group.attrs);
 error_free_setup_event_lines:
 	iio_free_chan_devattr_list(&ev_int->dev_attr_list);
 	kfree(ev_int);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/industrialio-sw-trigger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/industrialio-sw-trigger.c
@@ -58,8 +58,12 @@
 
 	t->group = configfs_register_default_group(iio_triggers_group, t->name,
 						&iio_trigger_type_group_type);
-	if (IS_ERR(t->group))
+	if (IS_ERR(t->group)) {
+		mutex_lock(&iio_trigger_types_lock);
+		list_del(&t->list);
+		mutex_unlock(&iio_trigger_types_lock);
 		ret = PTR_ERR(t->group);
+	}
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/industrialio-trigger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/industrialio-trigger.c
@@ -162,6 +162,39 @@
 	return trig;
 }
 
+static void iio_reenable_work_fn(struct work_struct *work)
+{
+	struct iio_trigger *trig = container_of(work, struct iio_trigger,
+						reenable_work);
+
+	/*
+	 * This 'might' occur after the trigger state is set to disabled -
+	 * in that case the driver should skip reenabling.
+	 */
+	trig->ops->reenable(trig);
+}
+
+/*
+ * In general, reenable callbacks may need to sleep and this path is
+ * not performance sensitive, so just queue up a work item
+ * to reneable the trigger for us.
+ *
+ * Races that can cause this.
+ * 1) A handler occurs entirely in interrupt context so the counter
+ *    the final decrement is still in this interrupt.
+ * 2) The trigger has been removed, but one last interrupt gets through.
+ *
+ * For (1) we must call reenable, but not in atomic context.
+ * For (2) it should be safe to call reenanble, if drivers never blindly
+ * reenable after state is off.
+ */
+static void iio_trigger_notify_done_atomic(struct iio_trigger *trig)
+{
+	if (atomic_dec_and_test(&trig->use_count) && trig->ops &&
+	    trig->ops->reenable)
+		schedule_work(&trig->reenable_work);
+}
+
 void iio_trigger_poll(struct iio_trigger *trig)
 {
 	int i;
@@ -173,7 +206,7 @@
 			if (trig->subirqs[i].enabled)
 				generic_handle_irq(trig->subirq_base + i);
 			else
-				iio_trigger_notify_done(trig);
+				iio_trigger_notify_done_atomic(trig);
 		}
 	}
 }
@@ -535,6 +568,7 @@
 	trig->dev.type = &iio_trig_type;
 	trig->dev.bus = &iio_bus_type;
 	device_initialize(&trig->dev);
+	INIT_WORK(&trig->reenable_work, iio_reenable_work_fn);
 
 	mutex_init(&trig->pool_lock);
 	trig->subirq_base = irq_alloc_descs(-1, 0,
@@ -556,7 +590,6 @@
 		irq_modify_status(trig->subirq_base + i,
 				  IRQ_NOREQUEST | IRQ_NOAUTOEN, IRQ_NOPROBE);
 	}
-	get_device(&trig->dev);
 
 	return trig;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/inkern.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/inkern.c
@@ -148,9 +148,10 @@
 
 	idev = bus_find_device(&iio_bus_type, NULL, iiospec.np,
 			       iio_dev_node_match);
-	of_node_put(iiospec.np);
-	if (idev == NULL)
+	if (idev == NULL) {
+		of_node_put(iiospec.np);
 		return -EPROBE_DEFER;
+	}
 
 	indio_dev = dev_to_iio_dev(idev);
 	channel->indio_dev = indio_dev;
@@ -158,6 +159,7 @@
 		index = indio_dev->info->of_xlate(indio_dev, &iiospec);
 	else
 		index = __of_iio_simple_xlate(indio_dev, &iiospec);
+	of_node_put(iiospec.np);
 	if (index < 0)
 		goto err_put;
 	channel->channel = &indio_dev->channels[index];
@@ -393,6 +395,8 @@
 	channel = of_iio_channel_get_by_name(np, channel_name);
 	if (IS_ERR(channel))
 		return channel;
+	if (!channel)
+		return ERR_PTR(-ENODEV);
 
 	ret = devm_add_action_or_reset(dev, devm_iio_channel_free, channel);
 	if (ret)
@@ -465,7 +469,7 @@
 	return chans;
 
 error_free_chans:
-	for (i = 0; i < nummaps; i++)
+	for (i = 0; i < mapind; i++)
 		iio_device_put(chans[i].indio_dev);
 	kfree(chans);
 error_ret:
@@ -578,42 +582,64 @@
 static int iio_convert_raw_to_processed_unlocked(struct iio_channel *chan,
 	int raw, int *processed, unsigned int scale)
 {
-	int scale_type, scale_val, scale_val2, offset;
+	int scale_type, scale_val, scale_val2;
+	int offset_type, offset_val, offset_val2;
 	s64 raw64 = raw;
-	int ret;
 
-	ret = iio_channel_read(chan, &offset, NULL, IIO_CHAN_INFO_OFFSET);
-	if (ret >= 0)
-		raw64 += offset;
+	offset_type = iio_channel_read(chan, &offset_val, &offset_val2,
+				       IIO_CHAN_INFO_OFFSET);
+	if (offset_type >= 0) {
+		switch (offset_type) {
+		case IIO_VAL_INT:
+			break;
+		case IIO_VAL_INT_PLUS_MICRO:
+		case IIO_VAL_INT_PLUS_NANO:
+			/*
+			 * Both IIO_VAL_INT_PLUS_MICRO and IIO_VAL_INT_PLUS_NANO
+			 * implicitely truncate the offset to it's integer form.
+			 */
+			break;
+		case IIO_VAL_FRACTIONAL:
+			offset_val /= offset_val2;
+			break;
+		case IIO_VAL_FRACTIONAL_LOG2:
+			offset_val >>= offset_val2;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		raw64 += offset_val;
+	}
 
 	scale_type = iio_channel_read(chan, &scale_val, &scale_val2,
 					IIO_CHAN_INFO_SCALE);
 	if (scale_type < 0) {
 		/*
-		 * Just pass raw values as processed if no scaling is
-		 * available.
+		 * If no channel scaling is available apply consumer scale to
+		 * raw value and return.
 		 */
-		*processed = raw;
+		*processed = raw * scale;
 		return 0;
 	}
 
 	switch (scale_type) {
 	case IIO_VAL_INT:
-		*processed = raw64 * scale_val;
+		*processed = raw64 * scale_val * scale;
 		break;
 	case IIO_VAL_INT_PLUS_MICRO:
 		if (scale_val2 < 0)
-			*processed = -raw64 * scale_val;
+			*processed = -raw64 * scale_val * scale;
 		else
-			*processed = raw64 * scale_val;
+			*processed = raw64 * scale_val * scale;
 		*processed += div_s64(raw64 * (s64)scale_val2 * scale,
 				      1000000LL);
 		break;
 	case IIO_VAL_INT_PLUS_NANO:
 		if (scale_val2 < 0)
-			*processed = -raw64 * scale_val;
+			*processed = -raw64 * scale_val * scale;
 		else
-			*processed = raw64 * scale_val;
+			*processed = raw64 * scale_val * scale;
 		*processed += div_s64(raw64 * (s64)scale_val2 * scale,
 				      1000000000LL);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/Kconfig
@@ -294,6 +294,8 @@
 	tristate "ROHM RPR0521 ALS and proximity sensor driver"
 	depends on I2C
 	select REGMAP_I2C
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	help
 	  Say Y here if you want to build support for ROHM's RPR0521
 	  ambient light and proximity sensor device.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/al3010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/al3010.c
@@ -87,7 +87,12 @@
 	int ret;
 
 	ret = al3010_set_pwr(data->client, true);
+	if (ret < 0)
+		return ret;
 
+	ret = devm_add_action_or_reset(&data->client->dev,
+				       al3010_set_pwr_off,
+				       data);
 	if (ret < 0)
 		return ret;
 
@@ -191,12 +196,6 @@
 		return ret;
 	}
 
-	ret = devm_add_action_or_reset(&client->dev,
-					al3010_set_pwr_off,
-					data);
-	if (ret < 0)
-		return ret;
-
 	return devm_iio_device_register(&client->dev, indio_dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/apds9960.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/apds9960.c
@@ -54,9 +54,6 @@
 #define APDS9960_REG_CONTROL_PGAIN_MASK_SHIFT	2
 
 #define APDS9960_REG_CONFIG_2	0x90
-#define APDS9960_REG_CONFIG_2_GGAIN_MASK	0x60
-#define APDS9960_REG_CONFIG_2_GGAIN_MASK_SHIFT	5
-
 #define APDS9960_REG_ID		0x92
 
 #define APDS9960_REG_STATUS	0x93
@@ -77,6 +74,9 @@
 #define APDS9960_REG_GCONF_1_GFIFO_THRES_MASK_SHIFT	6
 
 #define APDS9960_REG_GCONF_2	0xa3
+#define APDS9960_REG_GCONF_2_GGAIN_MASK			0x60
+#define APDS9960_REG_GCONF_2_GGAIN_MASK_SHIFT		5
+
 #define APDS9960_REG_GOFFSET_U	0xa4
 #define APDS9960_REG_GOFFSET_D	0xa5
 #define APDS9960_REG_GPULSE	0xa6
@@ -396,9 +396,9 @@
 			}
 
 			ret = regmap_update_bits(data->regmap,
-				APDS9960_REG_CONFIG_2,
-				APDS9960_REG_CONFIG_2_GGAIN_MASK,
-				idx << APDS9960_REG_CONFIG_2_GGAIN_MASK_SHIFT);
+				APDS9960_REG_GCONF_2,
+				APDS9960_REG_GCONF_2_GGAIN_MASK,
+				idx << APDS9960_REG_GCONF_2_GGAIN_MASK_SHIFT);
 			if (!ret)
 				data->pxs_gain = idx;
 			mutex_unlock(&data->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/as73211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/as73211.c
@@ -154,6 +154,12 @@
 	BIT(AS73211_SCAN_INDEX_TEMP) | \
 	AS73211_SCAN_MASK_COLOR)
 
+static const unsigned long as73211_scan_masks[] = {
+	AS73211_SCAN_MASK_COLOR,
+	AS73211_SCAN_MASK_ALL,
+	0
+};
+
 static const struct iio_chan_spec as73211_channels[] = {
 	{
 		.type = IIO_TEMP,
@@ -602,9 +608,12 @@
 
 		/* AS73211 starts reading at address 2 */
 		ret = i2c_master_recv(data->client,
-				(char *)&scan.chan[1], 3 * sizeof(scan.chan[1]));
+				(char *)&scan.chan[0], 3 * sizeof(scan.chan[0]));
 		if (ret < 0)
 			goto done;
+
+		/* Avoid pushing uninitialized data */
+		scan.chan[3] = 0;
 	}
 
 	if (data_result) {
@@ -612,9 +621,15 @@
 		 * Saturate all channels (in case of overflows). Temperature channel
 		 * is not affected by overflows.
 		 */
-		scan.chan[1] = cpu_to_le16(U16_MAX);
-		scan.chan[2] = cpu_to_le16(U16_MAX);
-		scan.chan[3] = cpu_to_le16(U16_MAX);
+		if (*indio_dev->active_scan_mask == AS73211_SCAN_MASK_ALL) {
+			scan.chan[1] = cpu_to_le16(U16_MAX);
+			scan.chan[2] = cpu_to_le16(U16_MAX);
+			scan.chan[3] = cpu_to_le16(U16_MAX);
+		} else {
+			scan.chan[0] = cpu_to_le16(U16_MAX);
+			scan.chan[1] = cpu_to_le16(U16_MAX);
+			scan.chan[2] = cpu_to_le16(U16_MAX);
+		}
 	}
 
 	iio_push_to_buffers_with_timestamp(indio_dev, &scan, iio_get_time_ns(indio_dev));
@@ -684,6 +699,7 @@
 	indio_dev->channels = as73211_channels;
 	indio_dev->num_channels = ARRAY_SIZE(as73211_channels);
 	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->available_scan_masks = as73211_scan_masks;
 
 	ret = i2c_smbus_read_byte_data(data->client, AS73211_REG_OSR);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/cm32181.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/cm32181.c
@@ -429,6 +429,14 @@
 	.attrs			= &cm32181_attribute_group,
 };
 
+static void cm32181_unregister_dummy_client(void *data)
+{
+	struct i2c_client *client = data;
+
+	/* Unregister the dummy client */
+	i2c_unregister_device(client);
+}
+
 static int cm32181_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
@@ -458,8 +466,14 @@
 		client = i2c_acpi_new_device(dev, 1, &board_info);
 		if (IS_ERR(client))
 			return PTR_ERR(client);
+
+		ret = devm_add_action_or_reset(dev, cm32181_unregister_dummy_client, client);
+		if (ret)
+			return ret;
 	}
 
+	i2c_set_clientdata(client, indio_dev);
+
 	cm32181 = iio_priv(indio_dev);
 	cm32181->client = client;
 	cm32181->dev = dev;
@@ -486,6 +500,27 @@
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int cm32181_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_write_word_data(client, CM32181_REG_ADDR_CMD,
+					 CM32181_CMD_ALS_DISABLE);
+}
+
+static int cm32181_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct cm32181_chip *cm32181 = iio_priv(dev_get_drvdata(dev));
+
+	return i2c_smbus_write_word_data(client, CM32181_REG_ADDR_CMD,
+					 cm32181->conf_regs[CM32181_REG_ADDR_CMD]);
+}
+#endif
+
+SIMPLE_DEV_PM_OPS(cm32181_pm_ops, cm32181_suspend, cm32181_resume);
+
 static const struct of_device_id cm32181_of_match[] = {
 	{ .compatible = "capella,cm3218" },
 	{ .compatible = "capella,cm32181" },
@@ -506,6 +541,7 @@
 		.name	= "cm32181",
 		.acpi_match_table = ACPI_PTR(cm32181_acpi_match),
 		.of_match_table = cm32181_of_match,
+		.pm = &cm32181_pm_ops,
 	},
 	.probe_new	= cm32181_probe,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/cros_ec_light_prox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/cros_ec_light_prox.c
@@ -181,8 +181,7 @@
 		return -ENOMEM;
 
 	ret = cros_ec_sensors_core_init(pdev, indio_dev, true,
-					cros_ec_sensors_capture,
-					cros_ec_sensors_push_data);
+					cros_ec_sensors_capture);
 	if (ret)
 		return ret;
 
@@ -240,7 +239,8 @@
 
 	state->core.read_ec_sensors_data = cros_ec_sensors_read_cmd;
 
-	return devm_iio_device_register(dev, indio_dev);
+	return cros_ec_sensors_core_register(dev, indio_dev,
+					     cros_ec_sensors_push_data);
 }
 
 static const struct platform_device_id cros_ec_light_prox_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/hid-sensor-als.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/hid-sensor-als.c
@@ -228,6 +228,7 @@
 	case HID_USAGE_SENSOR_TIME_TIMESTAMP:
 		als_state->timestamp = hid_sensor_convert_timestamp(&als_state->common_attributes,
 								    *(s64 *)raw_data);
+		ret = 0;
 		break;
 	default:
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/isl29028.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/isl29028.c
@@ -625,7 +625,7 @@
 					 ISL29028_POWER_OFF_DELAY_MS);
 	pm_runtime_use_autosuspend(&client->dev);
 
-	ret = devm_iio_device_register(indio_dev->dev.parent, indio_dev);
+	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev,
 			"%s(): iio registration failed with error %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/ltr501.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/ltr501.c
@@ -1273,7 +1273,7 @@
 		ret = regmap_bulk_read(data->regmap, LTR501_ALS_DATA1,
 				       als_buf, sizeof(als_buf));
 		if (ret < 0)
-			return ret;
+			goto done;
 		if (test_bit(0, indio_dev->active_scan_mask))
 			scan.channels[j++] = le16_to_cpu(als_buf[1]);
 		if (test_bit(1, indio_dev->active_scan_mask))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/max44009.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/max44009.c
@@ -528,6 +528,12 @@
 	return devm_iio_device_register(&client->dev, indio_dev);
 }
 
+static const struct of_device_id max44009_of_match[] = {
+	{ .compatible = "maxim,max44009" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, max44009_of_match);
+
 static const struct i2c_device_id max44009_id[] = {
 	{ "max44009", 0 },
 	{ }
@@ -537,18 +543,13 @@
 static struct i2c_driver max44009_driver = {
 	.driver = {
 		.name = MAX44009_DRV_NAME,
+		.of_match_table = max44009_of_match,
 	},
 	.probe = max44009_probe,
 	.id_table = max44009_id,
 };
 module_i2c_driver(max44009_driver);
 
-static const struct of_device_id max44009_of_match[] = {
-	{ .compatible = "maxim,max44009" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, max44009_of_match);
-
 MODULE_AUTHOR("Robert Eshleman <bobbyeshleman@gmail.com>");
 MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("MAX44009 ambient light sensor driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/opt3001.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/opt3001.c
@@ -139,6 +139,10 @@
 		.val2 = 400000,
 	},
 	{
+		.val = 41932,
+		.val2 = 800000,
+	},
+	{
 		.val = 83865,
 		.val2 = 600000,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/stk3310.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/stk3310.c
@@ -546,9 +546,8 @@
 	mutex_lock(&data->lock);
 	ret = regmap_field_read(data->reg_flag_nf, &dir);
 	if (ret < 0) {
-		dev_err(&data->client->dev, "register read failed\n");
-		mutex_unlock(&data->lock);
-		return ret;
+		dev_err(&data->client->dev, "register read failed: %d\n", ret);
+		goto out;
 	}
 	event = IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, 1,
 				     IIO_EV_TYPE_THRESH,
@@ -560,6 +559,7 @@
 	ret = regmap_field_write(data->reg_flag_psint, 0);
 	if (ret < 0)
 		dev_err(&data->client->dev, "failed to reset interrupts\n");
+out:
 	mutex_unlock(&data->lock);
 
 	return IRQ_HANDLED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/tsl2563.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/tsl2563.c
@@ -705,6 +705,7 @@
 	struct iio_dev *indio_dev;
 	struct tsl2563_chip *chip;
 	struct tsl2563_platform_data *pdata = client->dev.platform_data;
+	unsigned long irq_flags;
 	int err = 0;
 	u8 id = 0;
 
@@ -760,10 +761,15 @@
 		indio_dev->info = &tsl2563_info_no_irq;
 
 	if (client->irq) {
+		irq_flags = irq_get_trigger_type(client->irq);
+		if (irq_flags == IRQF_TRIGGER_NONE)
+			irq_flags = IRQF_TRIGGER_RISING;
+		irq_flags |= IRQF_ONESHOT;
+
 		err = devm_request_threaded_irq(&client->dev, client->irq,
 					   NULL,
 					   &tsl2563_event_handler,
-					   IRQF_TRIGGER_RISING | IRQF_ONESHOT,
+					   irq_flags,
 					   "tsl2563_event",
 					   indio_dev);
 		if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/tsl2583.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/tsl2583.c
@@ -858,7 +858,7 @@
 					 TSL2583_POWER_OFF_DELAY_MS);
 	pm_runtime_use_autosuspend(&clientp->dev);
 
-	ret = devm_iio_device_register(indio_dev->dev.parent, indio_dev);
+	ret = iio_device_register(indio_dev);
 	if (ret) {
 		dev_err(&clientp->dev, "%s: iio registration failed\n",
 			__func__);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/tsl2772.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/tsl2772.c
@@ -606,6 +606,7 @@
 			return -EINVAL;
 		}
 	}
+	chip->settings.prox_diode = prox_diode_mask;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/vcnl4035.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/vcnl4035.c
@@ -8,6 +8,7 @@
  * TODO: Proximity
  */
 #include <linux/bitops.h>
+#include <linux/bitfield.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/pm_runtime.h>
@@ -42,6 +43,7 @@
 #define VCNL4035_ALS_PERS_MASK		GENMASK(3, 2)
 #define VCNL4035_INT_ALS_IF_H_MASK	BIT(12)
 #define VCNL4035_INT_ALS_IF_L_MASK	BIT(13)
+#define VCNL4035_DEV_ID_MASK		GENMASK(7, 0)
 
 /* Default values */
 #define VCNL4035_MODE_ALS_ENABLE	BIT(0)
@@ -103,7 +105,7 @@
 	struct iio_dev *indio_dev = pf->indio_dev;
 	struct vcnl4035_data *data = iio_priv(indio_dev);
 	/* Ensure naturally aligned timestamp */
-	u8 buffer[ALIGN(sizeof(u16), sizeof(s64)) + sizeof(s64)]  __aligned(8);
+	u8 buffer[ALIGN(sizeof(u16), sizeof(s64)) + sizeof(s64)]  __aligned(8) = { };
 	int ret;
 
 	ret = regmap_read(data->regmap, VCNL4035_ALS_DATA, (int *)buffer);
@@ -413,6 +415,7 @@
 		return ret;
 	}
 
+	id = FIELD_GET(VCNL4035_DEV_ID_MASK, id);
 	if (id != VCNL4035_DEV_ID_VAL) {
 		dev_err(&data->client->dev, "Wrong id, got %x, expected %x\n",
 			id, VCNL4035_DEV_ID_VAL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/light/veml6030.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/light/veml6030.c
@@ -99,9 +99,8 @@
 static ssize_t in_illuminance_period_available_show(struct device *dev,
 				struct device_attribute *attr, char *buf)
 {
+	struct veml6030_data *data = iio_priv(dev_to_iio_dev(dev));
 	int ret, reg, x;
-	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
-	struct veml6030_data *data = iio_priv(indio_dev);
 
 	ret = regmap_read(data->regmap, VEML6030_REG_ALS_CONF, &reg);
 	if (ret) {
@@ -523,7 +522,7 @@
 			}
 			if (mask == IIO_CHAN_INFO_PROCESSED) {
 				*val = (reg * data->cur_resolution) / 10000;
-				*val2 = (reg * data->cur_resolution) % 10000;
+				*val2 = (reg * data->cur_resolution) % 10000 * 100;
 				return IIO_VAL_INT_PLUS_MICRO;
 			}
 			*val = reg;
@@ -780,7 +779,7 @@
 
 	/* Cache currently active measurement parameters */
 	data->cur_gain = 3;
-	data->cur_resolution = 4608;
+	data->cur_resolution = 5376;
 	data->cur_integration_time = 3;
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/magnetometer/ak8975.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/magnetometer/ak8975.c
@@ -389,6 +389,7 @@
 	if (ret) {
 		dev_warn(&data->client->dev,
 			 "Failed to enable specified Vid supply\n");
+		regulator_disable(data->vdd);
 		return ret;
 	}
 
@@ -660,22 +661,8 @@
 	if (ret < 0)
 		return ret;
 
-	/* This will be executed only for non-interrupt based waiting case */
-	if (ret & data->def->ctrl_masks[ST1_DRDY]) {
-		ret = i2c_smbus_read_byte_data(client,
-					       data->def->ctrl_regs[ST2]);
-		if (ret < 0) {
-			dev_err(&client->dev, "Error in reading ST2\n");
-			return ret;
-		}
-		if (ret & (data->def->ctrl_masks[ST2_DERR] |
-			   data->def->ctrl_masks[ST2_HOFL])) {
-			dev_err(&client->dev, "ST2 status error 0x%x\n", ret);
-			return -EINVAL;
-		}
-	}
-
-	return 0;
+	/* Return with zero if the data is ready. */
+	return !data->def->ctrl_regs[ST1_DRDY];
 }
 
 /* Retrieve raw flux value for one of the x, y, or z axis.  */
@@ -702,6 +689,20 @@
 	if (ret < 0)
 		goto exit;
 
+	/* Read out ST2 for release lock on measurment data. */
+	ret = i2c_smbus_read_byte_data(client, data->def->ctrl_regs[ST2]);
+	if (ret < 0) {
+		dev_err(&client->dev, "Error in reading ST2\n");
+		goto exit;
+	}
+
+	if (ret & (data->def->ctrl_masks[ST2_DERR] |
+		   data->def->ctrl_masks[ST2_HOFL])) {
+		dev_err(&client->dev, "ST2 status error 0x%x\n", ret);
+		ret = -EINVAL;
+		goto exit;
+	}
+
 	mutex_unlock(&data->lock);
 
 	pm_runtime_mark_last_busy(&data->client->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/magnetometer/bmc150_magn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/magnetometer/bmc150_magn.c
@@ -962,13 +962,14 @@
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(dev, "unable to register iio device\n");
-		goto err_disable_runtime_pm;
+		goto err_pm_cleanup;
 	}
 
 	dev_dbg(dev, "Registered device %s\n", name);
 	return 0;
 
-err_disable_runtime_pm:
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(dev);
 	pm_runtime_disable(dev);
 err_buffer_cleanup:
 	iio_triggered_buffer_cleanup(indio_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/magnetometer/rm3100-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/magnetometer/rm3100-core.c
@@ -538,6 +538,7 @@
 	struct rm3100_data *data;
 	unsigned int tmp;
 	int ret;
+	int samp_rate_index;
 
 	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
 	if (!indio_dev)
@@ -595,9 +596,14 @@
 	ret = regmap_read(regmap, RM3100_REG_TMRC, &tmp);
 	if (ret < 0)
 		return ret;
+
+	samp_rate_index = tmp - RM3100_TMRC_OFFSET;
+	if (samp_rate_index < 0 || samp_rate_index >=  RM3100_SAMP_NUM) {
+		dev_err(dev, "The value read from RM3100_REG_TMRC is invalid!\n");
+		return -EINVAL;
+	}
 	/* Initializing max wait time, which is double conversion time. */
-	data->conversion_time = rm3100_samp_rates[tmp - RM3100_TMRC_OFFSET][2]
-				* 2;
+	data->conversion_time = rm3100_samp_rates[samp_rate_index][2] * 2;
 
 	/* Cycle count values may not be what we want. */
 	if ((tmp - RM3100_TMRC_OFFSET) == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/magnetometer/st_magn_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/magnetometer/st_magn_i2c.c
@@ -102,10 +102,10 @@
 {
 	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_magn_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/magnetometer/st_magn_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/magnetometer/st_magn_spi.c
@@ -96,10 +96,10 @@
 {
 	struct iio_dev *indio_dev = spi_get_drvdata(spi);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_magn_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/magnetometer/yamaha-yas530.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/magnetometer/yamaha-yas530.c
@@ -132,7 +132,7 @@
 	unsigned int version;
 	char name[16];
 	struct yas5xx_calibration calibration;
-	u8 hard_offsets[3];
+	s8 hard_offsets[3];
 	struct iio_mount_matrix orientation;
 	struct regmap *map;
 	struct regulator_bulk_data regs[2];
@@ -639,7 +639,7 @@
 	dev_dbg(yas5xx->dev, "calibration data: %*ph\n", 14, data);
 
 	/* Sanity check, is this all zeroes? */
-	if (memchr_inv(data, 0x00, 13)) {
+	if (memchr_inv(data, 0x00, 13) == NULL) {
 		if (!(data[13] & BIT(7)))
 			dev_warn(yas5xx->dev, "calibration is blank!\n");
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/bmp280-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/bmp280-core.c
@@ -1112,7 +1112,7 @@
 	 * however as it happens, the BMP085 shares the chip ID of BMP180
 	 * so we look for an IRQ if we have that.
 	 */
-	if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
+	if (irq > 0 && (chip_id  == BMP180_CHIP_ID)) {
 		ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
 		if (ret)
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/cros_ec_baro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/cros_ec_baro.c
@@ -138,8 +138,7 @@
 		return -ENOMEM;
 
 	ret = cros_ec_sensors_core_init(pdev, indio_dev, true,
-					cros_ec_sensors_capture,
-					cros_ec_sensors_push_data);
+					cros_ec_sensors_capture);
 	if (ret)
 		return ret;
 
@@ -186,7 +185,8 @@
 
 	state->core.read_ec_sensors_data = cros_ec_sensors_read_cmd;
 
-	return devm_iio_device_register(dev, indio_dev);
+	return cros_ec_sensors_core_register(dev, indio_dev,
+					     cros_ec_sensors_push_data);
 }
 
 static const struct platform_device_id cros_ec_baro_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/dps310.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/dps310.c
@@ -57,8 +57,8 @@
 #define  DPS310_RESET_MAGIC	0x09
 #define DPS310_COEF_BASE	0x10
 
-/* Make sure sleep time is <= 20ms for usleep_range */
-#define DPS310_POLL_SLEEP_US(t)		min(20000, (t) / 8)
+/* Make sure sleep time is <= 30ms for usleep_range */
+#define DPS310_POLL_SLEEP_US(t)		min(30000, (t) / 8)
 /* Silently handle error in rate value here */
 #define DPS310_POLL_TIMEOUT_US(rc)	((rc) <= 0 ? 1000000 : 1000000 / (rc))
 
@@ -89,6 +89,7 @@
 	s32 c00, c10, c20, c30, c01, c11, c21;
 	s32 pressure_raw;
 	s32 temp_raw;
+	bool timeout_recovery_failed;
 };
 
 static const struct iio_chan_spec dps310_channels[] = {
@@ -159,6 +160,102 @@
 	return 0;
 }
 
+/*
+ * Some versions of the chip will read temperatures in the ~60C range when
+ * it's actually ~20C. This is the manufacturer recommended workaround
+ * to correct the issue. The registers used below are undocumented.
+ */
+static int dps310_temp_workaround(struct dps310_data *data)
+{
+	int rc;
+	int reg;
+
+	rc = regmap_read(data->regmap, 0x32, &reg);
+	if (rc)
+		return rc;
+
+	/*
+	 * If bit 1 is set then the device is okay, and the workaround does not
+	 * need to be applied
+	 */
+	if (reg & BIT(1))
+		return 0;
+
+	rc = regmap_write(data->regmap, 0x0e, 0xA5);
+	if (rc)
+		return rc;
+
+	rc = regmap_write(data->regmap, 0x0f, 0x96);
+	if (rc)
+		return rc;
+
+	rc = regmap_write(data->regmap, 0x62, 0x02);
+	if (rc)
+		return rc;
+
+	rc = regmap_write(data->regmap, 0x0e, 0x00);
+	if (rc)
+		return rc;
+
+	return regmap_write(data->regmap, 0x0f, 0x00);
+}
+
+static int dps310_startup(struct dps310_data *data)
+{
+	int rc;
+	int ready;
+
+	/*
+	 * Set up pressure sensor in single sample, one measurement per second
+	 * mode
+	 */
+	rc = regmap_write(data->regmap, DPS310_PRS_CFG, 0);
+	if (rc)
+		return rc;
+
+	/*
+	 * Set up external (MEMS) temperature sensor in single sample, one
+	 * measurement per second mode
+	 */
+	rc = regmap_write(data->regmap, DPS310_TMP_CFG, DPS310_TMP_EXT);
+	if (rc)
+		return rc;
+
+	/* Temp and pressure shifts are disabled when PRC <= 8 */
+	rc = regmap_write_bits(data->regmap, DPS310_CFG_REG,
+			       DPS310_PRS_SHIFT_EN | DPS310_TMP_SHIFT_EN, 0);
+	if (rc)
+		return rc;
+
+	/* MEAS_CFG doesn't update correctly unless first written with 0 */
+	rc = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
+			       DPS310_MEAS_CTRL_BITS, 0);
+	if (rc)
+		return rc;
+
+	/* Turn on temperature and pressure measurement in the background */
+	rc = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
+			       DPS310_MEAS_CTRL_BITS, DPS310_PRS_EN |
+			       DPS310_TEMP_EN | DPS310_BACKGROUND);
+	if (rc)
+		return rc;
+
+	/*
+	 * Calibration coefficients required for reporting temperature.
+	 * They are available 40ms after the device has started
+	 */
+	rc = regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready,
+				      ready & DPS310_COEF_RDY, 10000, 40000);
+	if (rc)
+		return rc;
+
+	rc = dps310_get_coefs(data);
+	if (rc)
+		return rc;
+
+	return dps310_temp_workaround(data);
+}
+
 static int dps310_get_pres_precision(struct dps310_data *data)
 {
 	int rc;
@@ -297,11 +394,69 @@
 	return scale_factors[ilog2(rc)];
 }
 
+static int dps310_reset_wait(struct dps310_data *data)
+{
+	int rc;
+
+	rc = regmap_write(data->regmap, DPS310_RESET, DPS310_RESET_MAGIC);
+	if (rc)
+		return rc;
+
+	/* Wait for device chip access: 15ms in specification */
+	usleep_range(15000, 55000);
+	return 0;
+}
+
+static int dps310_reset_reinit(struct dps310_data *data)
+{
+	int rc;
+
+	rc = dps310_reset_wait(data);
+	if (rc)
+		return rc;
+
+	return dps310_startup(data);
+}
+
+static int dps310_ready_status(struct dps310_data *data, int ready_bit, int timeout)
+{
+	int sleep = DPS310_POLL_SLEEP_US(timeout);
+	int ready;
+
+	return regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready, ready & ready_bit,
+					sleep, timeout);
+}
+
+static int dps310_ready(struct dps310_data *data, int ready_bit, int timeout)
+{
+	int rc;
+
+	rc = dps310_ready_status(data, ready_bit, timeout);
+	if (rc) {
+		if (rc == -ETIMEDOUT && !data->timeout_recovery_failed) {
+			/* Reset and reinitialize the chip. */
+			if (dps310_reset_reinit(data)) {
+				data->timeout_recovery_failed = true;
+			} else {
+				/* Try again to get sensor ready status. */
+				if (dps310_ready_status(data, ready_bit, timeout))
+					data->timeout_recovery_failed = true;
+				else
+					return 0;
+			}
+		}
+
+		return rc;
+	}
+
+	data->timeout_recovery_failed = false;
+	return 0;
+}
+
 static int dps310_read_pres_raw(struct dps310_data *data)
 {
 	int rc;
 	int rate;
-	int ready;
 	int timeout;
 	s32 raw;
 	u8 val[3];
@@ -313,9 +468,7 @@
 	timeout = DPS310_POLL_TIMEOUT_US(rate);
 
 	/* Poll for sensor readiness; base the timeout upon the sample rate. */
-	rc = regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready,
-				      ready & DPS310_PRS_RDY,
-				      DPS310_POLL_SLEEP_US(timeout), timeout);
+	rc = dps310_ready(data, DPS310_PRS_RDY, timeout);
 	if (rc)
 		goto done;
 
@@ -352,7 +505,6 @@
 {
 	int rc;
 	int rate;
-	int ready;
 	int timeout;
 
 	if (mutex_lock_interruptible(&data->lock))
@@ -362,10 +514,8 @@
 	timeout = DPS310_POLL_TIMEOUT_US(rate);
 
 	/* Poll for sensor readiness; base the timeout upon the sample rate. */
-	rc = regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready,
-				      ready & DPS310_TMP_RDY,
-				      DPS310_POLL_SLEEP_US(timeout), timeout);
-	if (rc < 0)
+	rc = dps310_ready(data, DPS310_TMP_RDY, timeout);
+	if (rc)
 		goto done;
 
 	rc = dps310_read_temp_ready(data);
@@ -580,7 +730,7 @@
 	}
 }
 
-static int dps310_calculate_temp(struct dps310_data *data)
+static int dps310_calculate_temp(struct dps310_data *data, int *val)
 {
 	s64 c0;
 	s64 t;
@@ -596,7 +746,9 @@
 	t = c0 + ((s64)data->temp_raw * (s64)data->c1);
 
 	/* Convert to milliCelsius and scale the temperature */
-	return (int)div_s64(t * 1000LL, kt);
+	*val = (int)div_s64(t * 1000LL, kt);
+
+	return 0;
 }
 
 static int dps310_read_temp(struct dps310_data *data, int *val, int *val2,
@@ -618,11 +770,10 @@
 		if (rc)
 			return rc;
 
-		rc = dps310_calculate_temp(data);
-		if (rc < 0)
+		rc = dps310_calculate_temp(data, val);
+		if (rc)
 			return rc;
 
-		*val = rc;
 		return IIO_VAL_INT;
 
 	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
@@ -660,7 +811,7 @@
 {
 	struct dps310_data *data = action_data;
 
-	regmap_write(data->regmap, DPS310_RESET, DPS310_RESET_MAGIC);
+	dps310_reset_wait(data);
 }
 
 static const struct regmap_config dps310_regmap_config = {
@@ -677,52 +828,12 @@
 	.write_raw = dps310_write_raw,
 };
 
-/*
- * Some verions of chip will read temperatures in the ~60C range when
- * its actually ~20C. This is the manufacturer recommended workaround
- * to correct the issue. The registers used below are undocumented.
- */
-static int dps310_temp_workaround(struct dps310_data *data)
-{
-	int rc;
-	int reg;
-
-	rc = regmap_read(data->regmap, 0x32, &reg);
-	if (rc < 0)
-		return rc;
-
-	/*
-	 * If bit 1 is set then the device is okay, and the workaround does not
-	 * need to be applied
-	 */
-	if (reg & BIT(1))
-		return 0;
-
-	rc = regmap_write(data->regmap, 0x0e, 0xA5);
-	if (rc < 0)
-		return rc;
-
-	rc = regmap_write(data->regmap, 0x0f, 0x96);
-	if (rc < 0)
-		return rc;
-
-	rc = regmap_write(data->regmap, 0x62, 0x02);
-	if (rc < 0)
-		return rc;
-
-	rc = regmap_write(data->regmap, 0x0e, 0x00);
-	if (rc < 0)
-		return rc;
-
-	return regmap_write(data->regmap, 0x0f, 0x00);
-}
-
 static int dps310_probe(struct i2c_client *client,
 			const struct i2c_device_id *id)
 {
 	struct dps310_data *data;
 	struct iio_dev *iio;
-	int rc, ready;
+	int rc;
 
 	iio = devm_iio_device_alloc(&client->dev,  sizeof(*data));
 	if (!iio)
@@ -747,54 +858,8 @@
 	if (rc)
 		return rc;
 
-	/*
-	 * Set up pressure sensor in single sample, one measurement per second
-	 * mode
-	 */
-	rc = regmap_write(data->regmap, DPS310_PRS_CFG, 0);
-
-	/*
-	 * Set up external (MEMS) temperature sensor in single sample, one
-	 * measurement per second mode
-	 */
-	rc = regmap_write(data->regmap, DPS310_TMP_CFG, DPS310_TMP_EXT);
-	if (rc < 0)
-		return rc;
-
-	/* Temp and pressure shifts are disabled when PRC <= 8 */
-	rc = regmap_write_bits(data->regmap, DPS310_CFG_REG,
-			       DPS310_PRS_SHIFT_EN | DPS310_TMP_SHIFT_EN, 0);
-	if (rc < 0)
-		return rc;
-
-	/* MEAS_CFG doesn't update correctly unless first written with 0 */
-	rc = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
-			       DPS310_MEAS_CTRL_BITS, 0);
-	if (rc < 0)
-		return rc;
-
-	/* Turn on temperature and pressure measurement in the background */
-	rc = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
-			       DPS310_MEAS_CTRL_BITS, DPS310_PRS_EN |
-			       DPS310_TEMP_EN | DPS310_BACKGROUND);
-	if (rc < 0)
-		return rc;
-
-	/*
-	 * Calibration coefficients required for reporting temperature.
-	 * They are available 40ms after the device has started
-	 */
-	rc = regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready,
-				      ready & DPS310_COEF_RDY, 10000, 40000);
-	if (rc < 0)
-		return rc;
-
-	rc = dps310_get_coefs(data);
-	if (rc < 0)
-		return rc;
-
-	rc = dps310_temp_workaround(data);
-	if (rc < 0)
+	rc = dps310_startup(data);
+	if (rc)
 		return rc;
 
 	rc = devm_iio_device_register(&client->dev, iio);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/ms5611.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/ms5611.h
@@ -25,13 +25,6 @@
 	MS5607,
 };
 
-struct ms5611_chip_info {
-	u16 prom[MS5611_PROM_WORDS_NB];
-
-	int (*temp_and_pressure_compensate)(struct ms5611_chip_info *chip_info,
-					    s32 *temp, s32 *pressure);
-};
-
 /*
  * OverSampling Rate descriptor.
  * Warning: cmd MUST be kept aligned on a word boundary (see
@@ -50,12 +43,15 @@
 	const struct ms5611_osr *pressure_osr;
 	const struct ms5611_osr *temp_osr;
 
-	int (*reset)(struct device *dev);
-	int (*read_prom_word)(struct device *dev, int index, u16 *word);
-	int (*read_adc_temp_and_pressure)(struct device *dev,
+	u16 prom[MS5611_PROM_WORDS_NB];
+
+	int (*reset)(struct ms5611_state *st);
+	int (*read_prom_word)(struct ms5611_state *st, int index, u16 *word);
+	int (*read_adc_temp_and_pressure)(struct ms5611_state *st,
 					  s32 *temp, s32 *pressure);
 
-	struct ms5611_chip_info *chip_info;
+	int (*compensate_temp_and_pressure)(struct ms5611_state *st, s32 *temp,
+					  s32 *pressure);
 	struct regulator *vdd;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/ms5611_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/ms5611_core.c
@@ -76,7 +76,7 @@
 
 	crc = (crc >> 12) & 0x000F;
 
-	return crc_orig != 0x0000 && crc == crc_orig;
+	return crc == crc_orig;
 }
 
 static int ms5611_read_prom(struct iio_dev *indio_dev)
@@ -85,8 +85,7 @@
 	struct ms5611_state *st = iio_priv(indio_dev);
 
 	for (i = 0; i < MS5611_PROM_WORDS_NB; i++) {
-		ret = st->read_prom_word(&indio_dev->dev,
-					 i, &st->chip_info->prom[i]);
+		ret = st->read_prom_word(st, i, &st->prom[i]);
 		if (ret < 0) {
 			dev_err(&indio_dev->dev,
 				"failed to read prom at %d\n", i);
@@ -94,7 +93,7 @@
 		}
 	}
 
-	if (!ms5611_prom_is_valid(st->chip_info->prom, MS5611_PROM_WORDS_NB)) {
+	if (!ms5611_prom_is_valid(st->prom, MS5611_PROM_WORDS_NB)) {
 		dev_err(&indio_dev->dev, "PROM integrity check failed\n");
 		return -ENODEV;
 	}
@@ -108,28 +107,27 @@
 	int ret;
 	struct ms5611_state *st = iio_priv(indio_dev);
 
-	ret = st->read_adc_temp_and_pressure(&indio_dev->dev, temp, pressure);
+	ret = st->read_adc_temp_and_pressure(st, temp, pressure);
 	if (ret < 0) {
 		dev_err(&indio_dev->dev,
 			"failed to read temperature and pressure\n");
 		return ret;
 	}
 
-	return st->chip_info->temp_and_pressure_compensate(st->chip_info,
-							   temp, pressure);
+	return st->compensate_temp_and_pressure(st, temp, pressure);
 }
 
-static int ms5611_temp_and_pressure_compensate(struct ms5611_chip_info *chip_info,
+static int ms5611_temp_and_pressure_compensate(struct ms5611_state *st,
 					       s32 *temp, s32 *pressure)
 {
 	s32 t = *temp, p = *pressure;
 	s64 off, sens, dt;
 
-	dt = t - (chip_info->prom[5] << 8);
-	off = ((s64)chip_info->prom[2] << 16) + ((chip_info->prom[4] * dt) >> 7);
-	sens = ((s64)chip_info->prom[1] << 15) + ((chip_info->prom[3] * dt) >> 8);
+	dt = t - (st->prom[5] << 8);
+	off = ((s64)st->prom[2] << 16) + ((st->prom[4] * dt) >> 7);
+	sens = ((s64)st->prom[1] << 15) + ((st->prom[3] * dt) >> 8);
 
-	t = 2000 + ((chip_info->prom[6] * dt) >> 23);
+	t = 2000 + ((st->prom[6] * dt) >> 23);
 	if (t < 2000) {
 		s64 off2, sens2, t2;
 
@@ -155,17 +153,17 @@
 	return 0;
 }
 
-static int ms5607_temp_and_pressure_compensate(struct ms5611_chip_info *chip_info,
+static int ms5607_temp_and_pressure_compensate(struct ms5611_state *st,
 					       s32 *temp, s32 *pressure)
 {
 	s32 t = *temp, p = *pressure;
 	s64 off, sens, dt;
 
-	dt = t - (chip_info->prom[5] << 8);
-	off = ((s64)chip_info->prom[2] << 17) + ((chip_info->prom[4] * dt) >> 6);
-	sens = ((s64)chip_info->prom[1] << 16) + ((chip_info->prom[3] * dt) >> 7);
+	dt = t - (st->prom[5] << 8);
+	off = ((s64)st->prom[2] << 17) + ((st->prom[4] * dt) >> 6);
+	sens = ((s64)st->prom[1] << 16) + ((st->prom[3] * dt) >> 7);
 
-	t = 2000 + ((chip_info->prom[6] * dt) >> 23);
+	t = 2000 + ((st->prom[6] * dt) >> 23);
 	if (t < 2000) {
 		s64 off2, sens2, t2, tmp;
 
@@ -196,7 +194,7 @@
 	int ret;
 	struct ms5611_state *st = iio_priv(indio_dev);
 
-	ret = st->reset(&indio_dev->dev);
+	ret = st->reset(st);
 	if (ret < 0) {
 		dev_err(&indio_dev->dev, "failed to reset device\n");
 		return ret;
@@ -343,15 +341,6 @@
 
 static const unsigned long ms5611_scan_masks[] = {0x3, 0};
 
-static struct ms5611_chip_info chip_info_tbl[] = {
-	[MS5611] = {
-		.temp_and_pressure_compensate = ms5611_temp_and_pressure_compensate,
-	},
-	[MS5607] = {
-		.temp_and_pressure_compensate = ms5607_temp_and_pressure_compensate,
-	}
-};
-
 static const struct iio_chan_spec ms5611_channels[] = {
 	{
 		.type = IIO_PRESSURE,
@@ -434,7 +423,20 @@
 	struct ms5611_state *st = iio_priv(indio_dev);
 
 	mutex_init(&st->lock);
-	st->chip_info = &chip_info_tbl[type];
+
+	switch (type) {
+	case MS5611:
+		st->compensate_temp_and_pressure =
+			ms5611_temp_and_pressure_compensate;
+		break;
+	case MS5607:
+		st->compensate_temp_and_pressure =
+			ms5607_temp_and_pressure_compensate;
+		break;
+	default:
+		return -EINVAL;
+	}
+
 	st->temp_osr =
 		&ms5611_avail_temp_osr[ARRAY_SIZE(ms5611_avail_temp_osr) - 1];
 	st->pressure_osr =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/ms5611_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/ms5611_i2c.c
@@ -20,17 +20,15 @@
 
 #include "ms5611.h"
 
-static int ms5611_i2c_reset(struct device *dev)
+static int ms5611_i2c_reset(struct ms5611_state *st)
 {
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
-
 	return i2c_smbus_write_byte(st->client, MS5611_RESET);
 }
 
-static int ms5611_i2c_read_prom_word(struct device *dev, int index, u16 *word)
+static int ms5611_i2c_read_prom_word(struct ms5611_state *st, int index,
+				     u16 *word)
 {
 	int ret;
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
 
 	ret = i2c_smbus_read_word_swapped(st->client,
 			MS5611_READ_PROM_WORD + (index << 1));
@@ -57,11 +55,10 @@
 	return 0;
 }
 
-static int ms5611_i2c_read_adc_temp_and_pressure(struct device *dev,
+static int ms5611_i2c_read_adc_temp_and_pressure(struct ms5611_state *st,
 						 s32 *temp, s32 *pressure)
 {
 	int ret;
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
 	const struct ms5611_osr *osr = st->temp_osr;
 
 	ret = i2c_smbus_write_byte(st->client, osr->cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/ms5611_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/ms5611_spi.c
@@ -15,18 +15,17 @@
 
 #include "ms5611.h"
 
-static int ms5611_spi_reset(struct device *dev)
+static int ms5611_spi_reset(struct ms5611_state *st)
 {
 	u8 cmd = MS5611_RESET;
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
 
 	return spi_write_then_read(st->client, &cmd, 1, NULL, 0);
 }
 
-static int ms5611_spi_read_prom_word(struct device *dev, int index, u16 *word)
+static int ms5611_spi_read_prom_word(struct ms5611_state *st, int index,
+				     u16 *word)
 {
 	int ret;
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
 
 	ret = spi_w8r16be(st->client, MS5611_READ_PROM_WORD + (index << 1));
 	if (ret < 0)
@@ -37,11 +36,10 @@
 	return 0;
 }
 
-static int ms5611_spi_read_adc(struct device *dev, s32 *val)
+static int ms5611_spi_read_adc(struct ms5611_state *st, s32 *val)
 {
 	int ret;
 	u8 buf[3] = { MS5611_READ_ADC };
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
 
 	ret = spi_write_then_read(st->client, buf, 1, buf, 3);
 	if (ret < 0)
@@ -52,11 +50,10 @@
 	return 0;
 }
 
-static int ms5611_spi_read_adc_temp_and_pressure(struct device *dev,
+static int ms5611_spi_read_adc_temp_and_pressure(struct ms5611_state *st,
 						 s32 *temp, s32 *pressure)
 {
 	int ret;
-	struct ms5611_state *st = iio_priv(dev_to_iio_dev(dev));
 	const struct ms5611_osr *osr = st->temp_osr;
 
 	/*
@@ -68,7 +65,7 @@
 		return ret;
 
 	usleep_range(osr->conv_usec, osr->conv_usec + (osr->conv_usec / 10UL));
-	ret = ms5611_spi_read_adc(dev, temp);
+	ret = ms5611_spi_read_adc(st, temp);
 	if (ret < 0)
 		return ret;
 
@@ -78,7 +75,7 @@
 		return ret;
 
 	usleep_range(osr->conv_usec, osr->conv_usec + (osr->conv_usec / 10UL));
-	return ms5611_spi_read_adc(dev, pressure);
+	return ms5611_spi_read_adc(st, pressure);
 }
 
 static int ms5611_spi_probe(struct spi_device *spi)
@@ -94,7 +91,7 @@
 	spi_set_drvdata(spi, indio_dev);
 
 	spi->mode = SPI_MODE_0;
-	spi->max_speed_hz = 20000000;
+	spi->max_speed_hz = min(spi->max_speed_hz, 20000000U);
 	spi->bits_per_word = 8;
 	ret = spi_setup(spi);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/st_pressure_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/st_pressure_i2c.c
@@ -119,10 +119,10 @@
 {
 	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_press_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/st_pressure_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/st_pressure_spi.c
@@ -102,10 +102,10 @@
 {
 	struct iio_dev *indio_dev = spi_get_drvdata(spi);
 
-	st_sensors_power_disable(indio_dev);
-
 	st_press_common_remove(indio_dev);
 
+	st_sensors_power_disable(indio_dev);
+
 	return 0;
 }
 
@@ -117,6 +117,10 @@
 	{ LPS33HW_PRESS_DEV_NAME },
 	{ LPS35HW_PRESS_DEV_NAME },
 	{ LPS22HH_PRESS_DEV_NAME },
+	{ "lps001wp-press" },
+	{ "lps25h-press", },
+	{ "lps331ap-press" },
+	{ "lps22hb-press" },
 	{},
 };
 MODULE_DEVICE_TABLE(spi, st_press_id_table);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/pressure/zpa2326.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/pressure/zpa2326.c
@@ -586,6 +586,8 @@
 	}   sample;
 	int err;
 
+	memset(&sample, 0, sizeof(sample));
+
 	if (test_bit(0, indio_dev->active_scan_mask)) {
 		/* Get current pressure from hardware FIFO. */
 		err = zpa2326_dequeue_pressure(indio_dev, &sample.pressure);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/proximity/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/proximity/Kconfig
@@ -60,6 +60,8 @@
 config MB1232
 	tristate "MaxSonar I2CXL family ultrasonic sensors"
 	depends on I2C
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	help
 	  Say Y to build a driver for the ultrasonic sensors I2CXL of
 	  MaxBotix which have an i2c interface. It can be used to measure
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/proximity/vl53l0x-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/proximity/vl53l0x-i2c.c
@@ -104,6 +104,7 @@
 	u16 tries = 20;
 	u8 buffer[12];
 	int ret;
+	unsigned long time_left;
 
 	ret = i2c_smbus_write_byte_data(client, VL_REG_SYSRANGE_START, 1);
 	if (ret < 0)
@@ -112,10 +113,8 @@
 	if (data->client->irq) {
 		reinit_completion(&data->completion);
 
-		ret = wait_for_completion_timeout(&data->completion, HZ/10);
-		if (ret < 0)
-			return ret;
-		else if (ret == 0)
+		time_left = wait_for_completion_timeout(&data->completion, HZ/10);
+		if (time_left == 0)
 			return -ETIMEDOUT;
 
 		vl53l0x_clear_irq(data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/temperature/ltc2983.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/temperature/ltc2983.c
@@ -205,6 +205,7 @@
 	 * Holds the converted temperature
 	 */
 	__be32 temp ____cacheline_aligned;
+	__be32 chan_val;
 };
 
 struct ltc2983_sensor {
@@ -309,19 +310,18 @@
 	return 0;
 }
 
-static int __ltc2983_chan_assign_common(const struct ltc2983_data *st,
+static int __ltc2983_chan_assign_common(struct ltc2983_data *st,
 					const struct ltc2983_sensor *sensor,
 					u32 chan_val)
 {
 	u32 reg = LTC2983_CHAN_START_ADDR(sensor->chan);
-	__be32 __chan_val;
 
 	chan_val |= LTC2983_CHAN_TYPE(sensor->type);
 	dev_dbg(&st->spi->dev, "Assign reg:0x%04X, val:0x%08X\n", reg,
 		chan_val);
-	__chan_val = cpu_to_be32(chan_val);
-	return regmap_bulk_write(st->regmap, reg, &__chan_val,
-				 sizeof(__chan_val));
+	st->chan_val = cpu_to_be32(chan_val);
+	return regmap_bulk_write(st->regmap, reg, &st->chan_val,
+				 sizeof(st->chan_val));
 }
 
 static int __ltc2983_chan_custom_sensor_assign(struct ltc2983_data *st,
@@ -1376,13 +1376,6 @@
 		return ret;
 	}
 
-	st->iio_chan = devm_kzalloc(&st->spi->dev,
-				    st->iio_channels * sizeof(*st->iio_chan),
-				    GFP_KERNEL);
-
-	if (!st->iio_chan)
-		return -ENOMEM;
-
 	ret = regmap_update_bits(st->regmap, LTC2983_GLOBAL_CONFIG_REG,
 				 LTC2983_NOTCH_FREQ_MASK,
 				 LTC2983_NOTCH_FREQ(st->filter_notch_freq));
@@ -1494,6 +1487,12 @@
 	if (ret)
 		return ret;
 
+	st->iio_chan = devm_kzalloc(&spi->dev,
+				    st->iio_channels * sizeof(*st->iio_chan),
+				    GFP_KERNEL);
+	if (!st->iio_chan)
+		return -ENOMEM;
+
 	ret = ltc2983_setup(st, true);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/trigger/iio-trig-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/trigger/iio-trig-sysfs.c
@@ -195,6 +195,7 @@
 	}
 
 	iio_trigger_unregister(t->trig);
+	irq_work_sync(&t->work);
 	iio_trigger_free(t->trig);
 
 	list_del(&t->l);
@@ -207,9 +208,13 @@
 
 static int __init iio_sysfs_trig_init(void)
 {
+	int ret;
 	device_initialize(&iio_sysfs_trig_dev);
 	dev_set_name(&iio_sysfs_trig_dev, "iio_sysfs_trigger");
-	return device_add(&iio_sysfs_trig_dev);
+	ret = device_add(&iio_sysfs_trig_dev);
+	if (ret)
+		put_device(&iio_sysfs_trig_dev);
+	return ret;
 }
 module_init(iio_sysfs_trig_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iio/trigger/stm32-timer-trigger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iio/trigger/stm32-timer-trigger.c
@@ -912,6 +912,6 @@
 };
 module_platform_driver(stm32_timer_trigger_driver);
 
-MODULE_ALIAS("platform: stm32-timer-trigger");
+MODULE_ALIAS("platform:stm32-timer-trigger");
 MODULE_DESCRIPTION("STMicroelectronics STM32 Timer Trigger driver");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/Makefile
@@ -40,5 +40,5 @@
 				uverbs_std_types_srq.o \
 				uverbs_std_types_wq.o \
 				uverbs_std_types_qp.o
-ib_uverbs-$(CONFIG_INFINIBAND_USER_MEM) += umem.o umem_dmabuf.o
+ib_uverbs-$(CONFIG_INFINIBAND_USER_MEM) += umem.o umem_dmabuf.o peer_mem.o
 ib_uverbs-$(CONFIG_INFINIBAND_ON_DEMAND_PAGING) += umem_odp.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/cache.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/cache.c
@@ -794,7 +794,6 @@
 static void release_gid_table(struct ib_device *device,
 			      struct ib_gid_table *table)
 {
-	bool leak = false;
 	int i;
 
 	if (!table)
@@ -803,15 +802,12 @@
 	for (i = 0; i < table->sz; i++) {
 		if (is_gid_entry_free(table->data_vec[i]))
 			continue;
-		if (kref_read(&table->data_vec[i]->kref) > 1) {
-			dev_err(&device->dev,
-				"GID entry ref leak for index %d ref=%u\n", i,
-				kref_read(&table->data_vec[i]->kref));
-			leak = true;
-		}
+
+		WARN_ONCE(true,
+			  "GID entry ref leak for dev %s index %d ref=%u\n",
+			  dev_name(&device->dev), i,
+			  kref_read(&table->data_vec[i]->kref));
 	}
-	if (leak)
-		return;
 
 	mutex_destroy(&table->lock);
 	kfree(table->data_vec);
@@ -1627,8 +1623,10 @@
 
 	rdma_for_each_port (device, p) {
 		err = ib_cache_update(device, p, true, true, true);
-		if (err)
+		if (err) {
+			gid_table_cleanup_one(device);
 			return err;
+		}
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/cm.c
@@ -34,6 +34,7 @@
 MODULE_DESCRIPTION("InfiniBand CM");
 MODULE_LICENSE("Dual BSD/GPL");
 
+#define CM_DESTROY_ID_WAIT_TIMEOUT 10000 /* msecs */
 static const char * const ibcm_rej_reason_strs[] = {
 	[IB_CM_REJ_NO_QP]			= "no QP",
 	[IB_CM_REJ_NO_EEC]			= "no EEC",
@@ -1032,13 +1033,26 @@
 	}
 }
 
+static noinline void cm_destroy_id_wait_timeout(struct ib_cm_id *cm_id,
+						enum ib_cm_state old_state)
+{
+	struct cm_id_private *cm_id_priv;
+
+	cm_id_priv = container_of(cm_id, struct cm_id_private, id);
+	pr_err("%s: cm_id=%p timed out. state %d -> %d, refcnt=%d\n", __func__,
+	       cm_id, old_state, cm_id->state, refcount_read(&cm_id_priv->refcount));
+}
+
 static void cm_destroy_id(struct ib_cm_id *cm_id, int err)
 {
 	struct cm_id_private *cm_id_priv;
+	enum ib_cm_state old_state;
 	struct cm_work *work;
+	int ret;
 
 	cm_id_priv = container_of(cm_id, struct cm_id_private, id);
 	spin_lock_irq(&cm_id_priv->lock);
+	old_state = cm_id->state;
 retest:
 	switch (cm_id->state) {
 	case IB_CM_LISTEN:
@@ -1142,7 +1156,14 @@
 
 	xa_erase(&cm.local_id_table, cm_local_id(cm_id->local_id));
 	cm_deref_id(cm_id_priv);
-	wait_for_completion(&cm_id_priv->comp);
+	do {
+		ret = wait_for_completion_timeout(&cm_id_priv->comp,
+						  msecs_to_jiffies(
+						  CM_DESTROY_ID_WAIT_TIMEOUT));
+		if (!ret) /* timeout happened */
+			cm_destroy_id_wait_timeout(cm_id, old_state);
+	} while (!ret);
+
 	while ((work = cm_dequeue_work(cm_id_priv)) != NULL)
 		cm_free_work(work);
 
@@ -1252,8 +1273,10 @@
 		return ERR_CAST(cm_id_priv);
 
 	err = cm_init_listen(cm_id_priv, service_id, 0);
-	if (err)
+	if (err) {
+		ib_destroy_cm_id(&cm_id_priv->id);
 		return ERR_PTR(err);
+	}
 
 	spin_lock_irq(&cm_id_priv->lock);
 	listen_id_priv = cm_insert_listen(cm_id_priv, cm_handler);
@@ -1630,14 +1653,13 @@
 
 static void cm_format_path_lid_from_req(struct cm_req_msg *req_msg,
 					struct sa_path_rec *primary_path,
-					struct sa_path_rec *alt_path)
+					struct sa_path_rec *alt_path,
+					struct ib_wc *wc)
 {
 	u32 lid;
 
 	if (primary_path->rec_type != SA_PATH_REC_TYPE_OPA) {
-		sa_path_set_dlid(primary_path,
-				 IBA_GET(CM_REQ_PRIMARY_LOCAL_PORT_LID,
-					 req_msg));
+		sa_path_set_dlid(primary_path, wc->slid);
 		sa_path_set_slid(primary_path,
 				 IBA_GET(CM_REQ_PRIMARY_REMOTE_PORT_LID,
 					 req_msg));
@@ -1674,7 +1696,8 @@
 
 static void cm_format_paths_from_req(struct cm_req_msg *req_msg,
 				     struct sa_path_rec *primary_path,
-				     struct sa_path_rec *alt_path)
+				     struct sa_path_rec *alt_path,
+				     struct ib_wc *wc)
 {
 	primary_path->dgid =
 		*IBA_GET_MEM_PTR(CM_REQ_PRIMARY_LOCAL_PORT_GID, req_msg);
@@ -1732,7 +1755,7 @@
 		if (sa_path_is_roce(alt_path))
 			alt_path->roce.route_resolved = false;
 	}
-	cm_format_path_lid_from_req(req_msg, primary_path, alt_path);
+	cm_format_path_lid_from_req(req_msg, primary_path, alt_path, wc);
 }
 
 static u16 cm_get_bth_pkey(struct cm_work *work)
@@ -2146,7 +2169,7 @@
 	if (cm_req_has_alt_path(req_msg))
 		work->path[1].rec_type = work->path[0].rec_type;
 	cm_format_paths_from_req(req_msg, &work->path[0],
-				 &work->path[1]);
+				 &work->path[1], work->mad_recv_wc->wc);
 	if (cm_id_priv->av.ah_attr.type == RDMA_AH_ATTR_TYPE_ROCE)
 		sa_path_set_dmac(&work->path[0],
 				 cm_id_priv->av.ah_attr.roce.dmac);
@@ -2824,6 +2847,7 @@
 	switch (cm_id_priv->id.state) {
 	case IB_CM_REP_SENT:
 	case IB_CM_DREQ_SENT:
+	case IB_CM_MRA_REP_RCVD:
 		ib_cancel_mad(cm_id_priv->msg);
 		break;
 	case IB_CM_ESTABLISHED:
@@ -2831,8 +2855,6 @@
 		    cm_id_priv->id.lap_state == IB_CM_MRA_LAP_RCVD)
 			ib_cancel_mad(cm_id_priv->msg);
 		break;
-	case IB_CM_MRA_REP_RCVD:
-		break;
 	case IB_CM_TIMEWAIT:
 		atomic_long_inc(&work->port->counters[CM_RECV_DUPLICATES]
 						     [CM_DREQ_COUNTER]);
@@ -2913,6 +2935,8 @@
 	    (ari && ari_length > IB_CM_REJ_ARI_LENGTH))
 		return -EINVAL;
 
+	trace_icm_send_rej(&cm_id_priv->id, reason);
+
 	switch (state) {
 	case IB_CM_REQ_SENT:
 	case IB_CM_MRA_REQ_RCVD:
@@ -2943,7 +2967,6 @@
 		return -EINVAL;
 	}
 
-	trace_icm_send_rej(&cm_id_priv->id, reason);
 	ret = ib_post_send_mad(msg, NULL);
 	if (ret) {
 		cm_free_msg(msg);
@@ -3322,7 +3345,7 @@
 	ret = cm_init_av_by_path(param->alternate_path, NULL, &alt_av);
 	if (ret) {
 		rdma_destroy_ah_attr(&ah_attr);
-		return -EINVAL;
+		goto deref;
 	}
 
 	spin_lock_irq(&cm_id_priv->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/cm_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/cm_trace.h
@@ -16,7 +16,7 @@
 
 #include <linux/tracepoint.h>
 #include <rdma/ib_cm.h>
-#include <trace/events/rdma.h>
+#include <trace/misc/rdma.h>
 
 /*
  * enum ib_cm_state, from include/rdma/ib_cm.h
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/cma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/cma.c
@@ -67,8 +67,8 @@
 	[RDMA_CM_EVENT_TIMEWAIT_EXIT]	 = "timewait exit",
 };
 
-static void cma_set_mgid(struct rdma_id_private *id_priv, struct sockaddr *addr,
-			 union ib_gid *mgid);
+static void cma_iboe_set_mgid(struct sockaddr *addr, union ib_gid *mgid,
+			      enum ib_gid_type gid_type);
 
 const char *__attribute_const__ rdma_event_msg(enum rdma_cm_event_type event)
 {
@@ -496,22 +496,11 @@
 	return id_priv->id.route.addr.src_addr.ss_family;
 }
 
-static int cma_set_qkey(struct rdma_id_private *id_priv, u32 qkey)
+static int cma_set_default_qkey(struct rdma_id_private *id_priv)
 {
 	struct ib_sa_mcmember_rec rec;
 	int ret = 0;
 
-	if (id_priv->qkey) {
-		if (qkey && id_priv->qkey != qkey)
-			return -EINVAL;
-		return 0;
-	}
-
-	if (qkey) {
-		id_priv->qkey = qkey;
-		return 0;
-	}
-
 	switch (id_priv->id.ps) {
 	case RDMA_PS_UDP:
 	case RDMA_PS_IB:
@@ -531,6 +520,16 @@
 	return ret;
 }
 
+static int cma_set_qkey(struct rdma_id_private *id_priv, u32 qkey)
+{
+	if (!qkey ||
+	    (id_priv->qkey && (id_priv->qkey != qkey)))
+		return -EINVAL;
+
+	id_priv->qkey = qkey;
+	return 0;
+}
+
 static void cma_translate_ib(struct sockaddr_ib *sib, struct rdma_dev_addr *dev_addr)
 {
 	dev_addr->dev_type = ARPHRD_INFINIBAND;
@@ -766,6 +765,7 @@
 	unsigned int p;
 	u16 pkey, index;
 	enum ib_port_state port_state;
+	int ret;
 	int i;
 
 	cma_dev = NULL;
@@ -784,9 +784,14 @@
 
 			if (ib_get_cached_port_state(cur_dev->device, p, &port_state))
 				continue;
-			for (i = 0; !rdma_query_gid(cur_dev->device,
-						    p, i, &gid);
-			     i++) {
+
+			for (i = 0; i < cur_dev->device->port_data[p].immutable.gid_tbl_len;
+			     ++i) {
+				ret = rdma_query_gid(cur_dev->device, p, i,
+						     &gid);
+				if (ret)
+					continue;
+
 				if (!memcmp(&gid, dgid, sizeof(gid))) {
 					cma_dev = cur_dev;
 					sgid = gid;
@@ -1093,7 +1098,7 @@
 	*qp_attr_mask = IB_QP_STATE | IB_QP_PKEY_INDEX | IB_QP_PORT;
 
 	if (id_priv->id.qp_type == IB_QPT_UD) {
-		ret = cma_set_qkey(id_priv, 0);
+		ret = cma_set_default_qkey(id_priv);
 		if (ret)
 			return ret;
 
@@ -1427,7 +1432,7 @@
 		return false;
 
 	memset(&fl4, 0, sizeof(fl4));
-	fl4.flowi4_iif = net_dev->ifindex;
+	fl4.flowi4_oif = net_dev->ifindex;
 	fl4.daddr = daddr;
 	fl4.saddr = saddr;
 
@@ -1712,8 +1717,8 @@
 		}
 
 		if (!validate_net_dev(*net_dev,
-				 (struct sockaddr *)&req->listen_addr_storage,
-				 (struct sockaddr *)&req->src_addr_storage)) {
+				 (struct sockaddr *)&req->src_addr_storage,
+				 (struct sockaddr *)&req->listen_addr_storage)) {
 			id_priv = ERR_PTR(-EHOSTUNREACH);
 			goto err;
 		}
@@ -1838,17 +1843,19 @@
 		if (dev_addr->bound_dev_if)
 			ndev = dev_get_by_index(dev_addr->net,
 						dev_addr->bound_dev_if);
-		if (ndev) {
+		if (ndev && !send_only) {
+			enum ib_gid_type gid_type;
 			union ib_gid mgid;
 
-			cma_set_mgid(id_priv, (struct sockaddr *)&mc->addr,
-				     &mgid);
-
-			if (!send_only)
-				cma_igmp_send(ndev, &mgid, false);
-
-			dev_put(ndev);
+			gid_type = id_priv->cma_dev->default_gid_type
+					   [id_priv->id.port_num -
+					    rdma_start_port(
+						    id_priv->cma_dev->device)];
+			cma_iboe_set_mgid((struct sockaddr *)&mc->addr, &mgid,
+					  gid_type);
+			cma_igmp_send(ndev, &mgid, false);
 		}
+		dev_put(ndev);
 
 		cancel_work_sync(&mc->iboe_join.work);
 	}
@@ -2632,7 +2639,7 @@
 {
 	struct rdma_id_private *id_priv;
 
-	if (id->qp_type != IB_QPT_RC)
+	if (id->qp_type != IB_QPT_RC && id->qp_type != IB_QPT_XRC_INI)
 		return -EINVAL;
 
 	id_priv = container_of(id, struct rdma_id_private, id);
@@ -3106,7 +3113,7 @@
 	route->path_rec->traffic_class = tos;
 	route->path_rec->mtu = iboe_get_mtu(ndev->mtu);
 	route->path_rec->rate_selector = IB_SA_EQ;
-	route->path_rec->rate = iboe_get_rate(ndev);
+	route->path_rec->rate = IB_RATE_PORT_CURRENT;
 	dev_put(ndev);
 	route->path_rec->packet_life_time_selector = IB_SA_EQ;
 	/* In case ACK timeout is set, use this value to calculate
@@ -3360,22 +3367,30 @@
 static int cma_bind_addr(struct rdma_cm_id *id, struct sockaddr *src_addr,
 			 const struct sockaddr *dst_addr)
 {
-	if (!src_addr || !src_addr->sa_family) {
-		src_addr = (struct sockaddr *) &id->route.addr.src_addr;
-		src_addr->sa_family = dst_addr->sa_family;
-		if (IS_ENABLED(CONFIG_IPV6) &&
-		    dst_addr->sa_family == AF_INET6) {
-			struct sockaddr_in6 *src_addr6 = (struct sockaddr_in6 *) src_addr;
-			struct sockaddr_in6 *dst_addr6 = (struct sockaddr_in6 *) dst_addr;
-			src_addr6->sin6_scope_id = dst_addr6->sin6_scope_id;
-			if (ipv6_addr_type(&dst_addr6->sin6_addr) & IPV6_ADDR_LINKLOCAL)
-				id->route.addr.dev_addr.bound_dev_if = dst_addr6->sin6_scope_id;
-		} else if (dst_addr->sa_family == AF_IB) {
-			((struct sockaddr_ib *) src_addr)->sib_pkey =
-				((struct sockaddr_ib *) dst_addr)->sib_pkey;
-		}
+	struct sockaddr_storage zero_sock = {};
+
+	if (src_addr && src_addr->sa_family)
+		return rdma_bind_addr(id, src_addr);
+
+	/*
+	 * When the src_addr is not specified, automatically supply an any addr
+	 */
+	zero_sock.ss_family = dst_addr->sa_family;
+	if (IS_ENABLED(CONFIG_IPV6) && dst_addr->sa_family == AF_INET6) {
+		struct sockaddr_in6 *src_addr6 =
+			(struct sockaddr_in6 *)&zero_sock;
+		struct sockaddr_in6 *dst_addr6 =
+			(struct sockaddr_in6 *)dst_addr;
+
+		src_addr6->sin6_scope_id = dst_addr6->sin6_scope_id;
+		if (ipv6_addr_type(&dst_addr6->sin6_addr) & IPV6_ADDR_LINKLOCAL)
+			id->route.addr.dev_addr.bound_dev_if =
+				dst_addr6->sin6_scope_id;
+	} else if (dst_addr->sa_family == AF_IB) {
+		((struct sockaddr_ib *)&zero_sock)->sib_pkey =
+			((struct sockaddr_ib *)dst_addr)->sib_pkey;
 	}
-	return rdma_bind_addr(id, src_addr);
+	return rdma_bind_addr(id, (struct sockaddr *)&zero_sock);
 }
 
 /*
@@ -4031,8 +4046,7 @@
 
 	memset(&req, 0, sizeof req);
 	offset = cma_user_data_offset(id_priv);
-	req.private_data_len = offset + conn_param->private_data_len;
-	if (req.private_data_len < conn_param->private_data_len)
+	if (check_add_overflow(offset, conn_param->private_data_len, &req.private_data_len))
 		return -EINVAL;
 
 	if (req.private_data_len) {
@@ -4091,8 +4105,7 @@
 
 	memset(&req, 0, sizeof req);
 	offset = cma_user_data_offset(id_priv);
-	req.private_data_len = offset + conn_param->private_data_len;
-	if (req.private_data_len < conn_param->private_data_len)
+	if (check_add_overflow(offset, conn_param->private_data_len, &req.private_data_len))
 		return -EINVAL;
 
 	if (req.private_data_len) {
@@ -4359,7 +4372,10 @@
 	memset(&rep, 0, sizeof rep);
 	rep.status = status;
 	if (status == IB_SIDR_SUCCESS) {
-		ret = cma_set_qkey(id_priv, qkey);
+		if (qkey)
+			ret = cma_set_qkey(id_priv, qkey);
+		else
+			ret = cma_set_default_qkey(id_priv);
 		if (ret)
 			return ret;
 		rep.qp_num = id_priv->qp_num;
@@ -4564,9 +4580,7 @@
 	enum ib_gid_type gid_type;
 	struct net_device *ndev;
 
-	if (!status)
-		status = cma_set_qkey(id_priv, be32_to_cpu(multicast->rec.qkey));
-	else
+	if (status)
 		pr_debug_ratelimited("RDMA CM: MULTICAST_ERROR: failed to join multicast. status %d\n",
 				     status);
 
@@ -4594,7 +4608,7 @@
 	}
 
 	event->param.ud.qp_num = 0xFFFFFF;
-	event->param.ud.qkey = be32_to_cpu(multicast->rec.qkey);
+	event->param.ud.qkey = id_priv->qkey;
 
 out:
 	if (ndev)
@@ -4613,8 +4627,11 @@
 	    READ_ONCE(id_priv->state) == RDMA_CM_DESTROYING)
 		goto out;
 
-	cma_make_mc_event(status, id_priv, multicast, &event, mc);
-	ret = cma_cm_event_handler(id_priv, &event);
+	ret = cma_set_qkey(id_priv, be32_to_cpu(multicast->rec.qkey));
+	if (!ret) {
+		cma_make_mc_event(status, id_priv, multicast, &event, mc);
+		ret = cma_cm_event_handler(id_priv, &event);
+	}
 	rdma_destroy_ah_attr(&event.param.ud.ah_attr);
 	WARN_ON(ret);
 
@@ -4667,9 +4684,11 @@
 	if (ret)
 		return ret;
 
-	ret = cma_set_qkey(id_priv, 0);
-	if (ret)
-		return ret;
+	if (!id_priv->qkey) {
+		ret = cma_set_default_qkey(id_priv);
+		if (ret)
+			return ret;
+	}
 
 	cma_set_mgid(id_priv, (struct sockaddr *) &mc->addr, &rec.mgid);
 	rec.qkey = cpu_to_be32(id_priv->qkey);
@@ -4732,7 +4751,7 @@
 	int err = 0;
 	struct sockaddr *addr = (struct sockaddr *)&mc->addr;
 	struct net_device *ndev = NULL;
-	struct ib_sa_multicast ib;
+	struct ib_sa_multicast ib = {};
 	enum ib_gid_type gid_type;
 	bool send_only;
 
@@ -4746,15 +4765,12 @@
 	cma_iboe_set_mgid(addr, &ib.rec.mgid, gid_type);
 
 	ib.rec.pkey = cpu_to_be16(0xffff);
-	if (id_priv->id.ps == RDMA_PS_UDP)
-		ib.rec.qkey = cpu_to_be32(RDMA_UDP_QKEY);
-
 	if (dev_addr->bound_dev_if)
 		ndev = dev_get_by_index(dev_addr->net, dev_addr->bound_dev_if);
 	if (!ndev)
 		return -ENODEV;
 
-	ib.rec.rate = iboe_get_rate(ndev);
+	ib.rec.rate = IB_RATE_PORT_CURRENT;
 	ib.rec.hop_limit = 1;
 	ib.rec.mtu = iboe_get_mtu(ndev->mtu);
 
@@ -4774,6 +4790,9 @@
 	if (err || !ib.rec.mtu)
 		return err ?: -EINVAL;
 
+	if (!id_priv->qkey)
+		cma_set_default_qkey(id_priv);
+
 	rdma_ip2gid((struct sockaddr *)&id_priv->id.route.addr.src_addr,
 		    &ib.rec.port_gid);
 	INIT_WORK(&mc->iboe_join.work, cma_iboe_join_work_handler);
@@ -4799,6 +4818,9 @@
 			    READ_ONCE(id_priv->state) != RDMA_CM_ADDR_RESOLVED))
 		return -EINVAL;
 
+	if (id_priv->id.qp_type != IB_QPT_UD)
+		return -EINVAL;
+
 	mc = kzalloc(sizeof(*mc), GFP_KERNEL);
 	if (!mc)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/cma_configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/cma_configfs.c
@@ -218,7 +218,7 @@
 		return -ENOMEM;
 
 	for (i = 0; i < ports_num; i++) {
-		char port_str[10];
+		char port_str[11];
 
 		ports[i].port_num = i + 1;
 		snprintf(port_str, sizeof(port_str), "%u", i + 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/cma_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/cma_trace.h
@@ -15,7 +15,7 @@
 #define _TRACE_RDMA_CMA_H
 
 #include <linux/tracepoint.h>
-#include <trace/events/rdma.h>
+#include <trace/misc/rdma.h>
 
 
 DECLARE_EVENT_CLASS(cma_fsm_class,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/device.c
@@ -542,6 +542,8 @@
 static void rdma_init_coredev(struct ib_core_device *coredev,
 			      struct ib_device *dev, struct net *net)
 {
+	bool is_full_dev = &dev->coredev == coredev;
+
 	/* This BUILD_BUG_ON is intended to catch layout change
 	 * of union of ib_core_device and device.
 	 * dev must be the first element as ib_core and providers
@@ -553,6 +555,13 @@
 
 	coredev->dev.class = &ib_class;
 	coredev->dev.groups = dev->groups;
+
+	/*
+	 * Don't expose hw counters outside of the init namespace.
+	 */
+	if (!is_full_dev && dev->hw_stats_attr_index)
+		coredev->dev.groups[dev->hw_stats_attr_index] = NULL;
+
 	device_initialize(&coredev->dev);
 	coredev->owner = dev;
 	INIT_LIST_HEAD(&coredev->port_list);
@@ -803,7 +812,7 @@
 	 * empty slots at the beginning.
 	 */
 	pdata_rcu = kzalloc(struct_size(pdata_rcu, pdata,
-					rdma_end_port(device) + 1),
+					size_add(rdma_end_port(device), 1)),
 			    GFP_KERNEL);
 	if (!pdata_rcu)
 		return -ENOMEM;
@@ -1729,7 +1738,7 @@
 {
 	int ret;
 
-	down_write(&clients_rwsem);
+	lockdep_assert_held(&clients_rwsem);
 	/*
 	 * The add/remove callbacks must be called in FIFO/LIFO order. To
 	 * achieve this we assign client_ids so they are sorted in
@@ -1738,14 +1747,11 @@
 	client->client_id = highest_client_id;
 	ret = xa_insert(&clients, client->client_id, client, GFP_KERNEL);
 	if (ret)
-		goto out;
+		return ret;
 
 	highest_client_id++;
 	xa_set_mark(&clients, client->client_id, CLIENT_REGISTERED);
-
-out:
-	up_write(&clients_rwsem);
-	return ret;
+	return 0;
 }
 
 static void remove_client_id(struct ib_client *client)
@@ -1775,25 +1781,35 @@
 {
 	struct ib_device *device;
 	unsigned long index;
+	bool need_unreg = false;
 	int ret;
 
 	refcount_set(&client->uses, 1);
 	init_completion(&client->uses_zero);
+
+	/*
+	 * The devices_rwsem is held in write mode to ensure that a racing
+	 * ib_register_device() sees a consisent view of clients and devices.
+	 */
+	down_write(&devices_rwsem);
+	down_write(&clients_rwsem);
 	ret = assign_client_id(client);
 	if (ret)
-		return ret;
+		goto out;
 
-	down_read(&devices_rwsem);
+	need_unreg = true;
 	xa_for_each_marked (&devices, index, device, DEVICE_REGISTERED) {
 		ret = add_client_context(device, client);
-		if (ret) {
-			up_read(&devices_rwsem);
-			ib_unregister_client(client);
-			return ret;
-		}
+		if (ret)
+			goto out;
 	}
-	up_read(&devices_rwsem);
-	return 0;
+	ret = 0;
+out:
+	up_write(&clients_rwsem);
+	up_write(&devices_rwsem);
+	if (need_unreg && ret)
+		ib_unregister_client(client);
+	return ret;
 }
 EXPORT_SYMBOL(ib_register_client);
 
@@ -2138,6 +2154,9 @@
 	unsigned long flags;
 	int ret;
 
+	if (!rdma_is_port_valid(ib_dev, port))
+		return -EINVAL;
+
 	/*
 	 * Drivers wish to call this before ib_register_driver, so we have to
 	 * setup the port data early.
@@ -2146,9 +2165,6 @@
 	if (ret)
 		return ret;
 
-	if (!rdma_is_port_valid(ib_dev, port))
-		return -EINVAL;
-
 	pdata = &ib_dev->port_data[port];
 	spin_lock_irqsave(&pdata->netdev_lock, flags);
 	old_ndev = rcu_dereference_protected(
@@ -2461,7 +2477,8 @@
 		     ++i) {
 			ret = rdma_query_gid(device, port, i, &tmp_gid);
 			if (ret)
-				return ret;
+				continue;
+
 			if (!memcmp(&tmp_gid, gid, sizeof *gid)) {
 				*port_num = port;
 				if (index)
@@ -2813,10 +2830,18 @@
 
 	nldev_init();
 	rdma_nl_register(RDMA_NL_LS, ibnl_ls_cb_table);
-	roce_gid_mgmt_init();
+	ret = roce_gid_mgmt_init();
+	if (ret) {
+		pr_warn("Couldn't init RoCE GID management\n");
+		goto err_parent;
+	}
 
 	return 0;
 
+err_parent:
+	rdma_nl_unregister(RDMA_NL_LS);
+	nldev_exit();
+	unregister_pernet_device(&rdma_dev_net_ops);
 err_compat:
 	unregister_blocking_lsm_notifier(&ibdev_lsm_nb);
 err_sa:
@@ -2839,8 +2864,8 @@
 static void __exit ib_core_cleanup(void)
 {
 	roce_gid_mgmt_cleanup();
-	nldev_exit();
 	rdma_nl_unregister(RDMA_NL_LS);
+	nldev_exit();
 	unregister_pernet_device(&rdma_dev_net_ops);
 	unregister_blocking_lsm_notifier(&ibdev_lsm_nb);
 	ib_sa_cleanup();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/ib_peer_mem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/ib_peer_mem.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB */
+/*
+ * Copyright (c) 2014-2020,  Mellanox Technologies. All rights reserved.
+ */
+#ifndef RDMA_IB_PEER_MEM_H
+#define RDMA_IB_PEER_MEM_H
+
+#include <rdma/peer_mem.h>
+#include <linux/kobject.h>
+#include <linux/xarray.h>
+#include <rdma/ib_umem.h>
+
+struct ib_peer_memory_statistics {
+	atomic64_t num_alloc_mrs;
+	atomic64_t num_dealloc_mrs;
+	atomic64_t num_reg_pages;
+	atomic64_t num_dereg_pages;
+	atomic64_t num_reg_bytes;
+	atomic64_t num_dereg_bytes;
+	unsigned long num_free_callbacks;
+};
+
+struct ib_peer_memory_client {
+	struct kobject kobj;
+	refcount_t usecnt;
+	struct completion usecnt_zero;
+	const struct peer_memory_client *peer_mem;
+	struct list_head core_peer_list;
+	struct ib_peer_memory_statistics stats;
+	struct xarray umem_xa;
+	u32 xa_cyclic_next;
+	bool invalidation_required;
+};
+
+enum ib_umem_mapped_state {
+	UMEM_PEER_UNMAPPED,
+	UMEM_PEER_MAPPED,
+	UMEM_PEER_INVALIDATED,
+};
+
+struct ib_umem_peer {
+	struct ib_umem umem;
+	struct kref kref;
+	/* peer memory that manages this umem */
+	struct ib_peer_memory_client *ib_peer_client;
+	void *peer_client_context;
+	umem_invalidate_func_t invalidation_func;
+	void *invalidation_private;
+	struct mutex mapping_lock;
+	enum ib_umem_mapped_state mapped_state;
+	u32 xa_id;
+	struct scatterlist *first_sg;
+	dma_addr_t first_dma_address;
+	unsigned int first_dma_length;
+	unsigned int first_length;
+	struct scatterlist *last_sg;
+	unsigned int last_dma_length;
+	unsigned int last_length;
+};
+
+struct ib_umem *ib_peer_umem_get(struct ib_umem *old_umem, int old_ret,
+				 unsigned long peer_mem_flags);
+void ib_peer_umem_release(struct ib_umem *umem);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/iwcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/iwcm.c
@@ -369,8 +369,10 @@
  *
  * Clean up all resources associated with the connection and release
  * the initial reference taken by iw_create_cm_id.
+ *
+ * Returns true if and only if the last cm_id_priv reference has been dropped.
  */
-static void destroy_cm_id(struct iw_cm_id *cm_id)
+static bool destroy_cm_id(struct iw_cm_id *cm_id)
 {
 	struct iwcm_id_private *cm_id_priv;
 	struct ib_qp *qp;
@@ -440,7 +442,7 @@
 		iwpm_remove_mapping(&cm_id->local_addr, RDMA_NL_IWCM);
 	}
 
-	(void)iwcm_deref_id(cm_id_priv);
+	return iwcm_deref_id(cm_id_priv);
 }
 
 /*
@@ -451,7 +453,8 @@
  */
 void iw_destroy_cm_id(struct iw_cm_id *cm_id)
 {
-	destroy_cm_id(cm_id);
+	if (!destroy_cm_id(cm_id))
+		flush_workqueue(iwcm_wq);
 }
 EXPORT_SYMBOL(iw_destroy_cm_id);
 
@@ -1035,7 +1038,7 @@
 		if (!test_bit(IWCM_F_DROP_EVENTS, &cm_id_priv->flags)) {
 			ret = process_event(cm_id_priv, &levent);
 			if (ret)
-				destroy_cm_id(&cm_id_priv->id);
+				WARN_ON_ONCE(destroy_cm_id(&cm_id_priv->id));
 		} else
 			pr_debug("dropping event %d\n", levent.event);
 		if (iwcm_deref_id(cm_id_priv))
@@ -1188,7 +1191,7 @@
 	if (ret)
 		return ret;
 
-	iwcm_wq = alloc_ordered_workqueue("iw_cm_wq", 0);
+	iwcm_wq = alloc_ordered_workqueue("iw_cm_wq", WQ_MEM_RECLAIM);
 	if (!iwcm_wq)
 		goto err_alloc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/mad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/mad.c
@@ -59,9 +59,6 @@
 			  struct ib_mad_qp_info *qp_info,
 			  struct trace_event_raw_ib_mad_send_template *entry)
 {
-	u16 pkey;
-	struct ib_device *dev = qp_info->port_priv->device;
-	u32 pnum = qp_info->port_priv->port_num;
 	struct ib_ud_wr *wr = &mad_send_wr->send_wr;
 	struct rdma_ah_attr attr = {};
 
@@ -69,8 +66,6 @@
 
 	/* These are common */
 	entry->sl = attr.sl;
-	ib_query_pkey(dev, pnum, wr->pkey_index, &pkey);
-	entry->pkey = pkey;
 	entry->rqpn = wr->remote_qpn;
 	entry->rqkey = wr->remote_qkey;
 	entry->dlid = rdma_ah_get_dlid(&attr);
@@ -2621,14 +2616,16 @@
 
 static void timeout_sends(struct work_struct *work)
 {
+	struct ib_mad_send_wr_private *mad_send_wr, *n;
 	struct ib_mad_agent_private *mad_agent_priv;
-	struct ib_mad_send_wr_private *mad_send_wr;
 	struct ib_mad_send_wc mad_send_wc;
+	struct list_head local_list;
 	unsigned long flags, delay;
 
 	mad_agent_priv = container_of(work, struct ib_mad_agent_private,
 				      timed_work.work);
 	mad_send_wc.vendor_err = 0;
+	INIT_LIST_HEAD(&local_list);
 
 	spin_lock_irqsave(&mad_agent_priv->lock, flags);
 	while (!list_empty(&mad_agent_priv->wait_list)) {
@@ -2646,13 +2643,16 @@
 			break;
 		}
 
-		list_del(&mad_send_wr->agent_list);
+		list_del_init(&mad_send_wr->agent_list);
 		if (mad_send_wr->status == IB_WC_SUCCESS &&
 		    !retry_send(mad_send_wr))
 			continue;
 
-		spin_unlock_irqrestore(&mad_agent_priv->lock, flags);
+		list_add_tail(&mad_send_wr->agent_list, &local_list);
+	}
+	spin_unlock_irqrestore(&mad_agent_priv->lock, flags);
 
+	list_for_each_entry_safe(mad_send_wr, n, &local_list, agent_list) {
 		if (mad_send_wr->status == IB_WC_SUCCESS)
 			mad_send_wc.status = IB_WC_RESP_TIMEOUT_ERR;
 		else
@@ -2660,11 +2660,8 @@
 		mad_send_wc.send_buf = &mad_send_wr->send_buf;
 		mad_agent_priv->agent.send_handler(&mad_agent_priv->agent,
 						   &mad_send_wc);
-
 		deref_mad_agent(mad_agent_priv);
-		spin_lock_irqsave(&mad_agent_priv->lock, flags);
 	}
-	spin_unlock_irqrestore(&mad_agent_priv->lock, flags);
 }
 
 /*
@@ -2674,11 +2671,11 @@
 				    struct ib_mad_private *mad)
 {
 	unsigned long flags;
-	int post, ret;
 	struct ib_mad_private *mad_priv;
 	struct ib_sge sg_list;
 	struct ib_recv_wr recv_wr;
 	struct ib_mad_queue *recv_queue = &qp_info->recv_queue;
+	int ret = 0;
 
 	/* Initialize common scatter list fields */
 	sg_list.lkey = qp_info->port_priv->pd->local_dma_lkey;
@@ -2688,7 +2685,7 @@
 	recv_wr.sg_list = &sg_list;
 	recv_wr.num_sge = 1;
 
-	do {
+	while (true) {
 		/* Allocate and map receive buffer */
 		if (mad) {
 			mad_priv = mad;
@@ -2696,10 +2693,8 @@
 		} else {
 			mad_priv = alloc_mad_private(port_mad_size(qp_info->port_priv),
 						     GFP_ATOMIC);
-			if (!mad_priv) {
-				ret = -ENOMEM;
-				break;
-			}
+			if (!mad_priv)
+				return -ENOMEM;
 		}
 		sg_list.length = mad_priv_dma_size(mad_priv);
 		sg_list.addr = ib_dma_map_single(qp_info->port_priv->device,
@@ -2708,37 +2703,41 @@
 						 DMA_FROM_DEVICE);
 		if (unlikely(ib_dma_mapping_error(qp_info->port_priv->device,
 						  sg_list.addr))) {
-			kfree(mad_priv);
 			ret = -ENOMEM;
-			break;
+			goto free_mad_priv;
 		}
 		mad_priv->header.mapping = sg_list.addr;
 		mad_priv->header.mad_list.mad_queue = recv_queue;
 		mad_priv->header.mad_list.cqe.done = ib_mad_recv_done;
 		recv_wr.wr_cqe = &mad_priv->header.mad_list.cqe;
-
-		/* Post receive WR */
 		spin_lock_irqsave(&recv_queue->lock, flags);
-		post = (++recv_queue->count < recv_queue->max_active);
-		list_add_tail(&mad_priv->header.mad_list.list, &recv_queue->list);
+		if (recv_queue->count >= recv_queue->max_active) {
+			/* Fully populated the receive queue */
+			spin_unlock_irqrestore(&recv_queue->lock, flags);
+			break;
+		}
+		recv_queue->count++;
+		list_add_tail(&mad_priv->header.mad_list.list,
+			      &recv_queue->list);
 		spin_unlock_irqrestore(&recv_queue->lock, flags);
+
 		ret = ib_post_recv(qp_info->qp, &recv_wr, NULL);
 		if (ret) {
 			spin_lock_irqsave(&recv_queue->lock, flags);
 			list_del(&mad_priv->header.mad_list.list);
 			recv_queue->count--;
 			spin_unlock_irqrestore(&recv_queue->lock, flags);
-			ib_dma_unmap_single(qp_info->port_priv->device,
-					    mad_priv->header.mapping,
-					    mad_priv_dma_size(mad_priv),
-					    DMA_FROM_DEVICE);
-			kfree(mad_priv);
 			dev_err(&qp_info->port_priv->device->dev,
 				"ib_post_recv failed: %d\n", ret);
 			break;
 		}
-	} while (post);
+	}
 
+	ib_dma_unmap_single(qp_info->port_priv->device,
+			    mad_priv->header.mapping,
+			    mad_priv_dma_size(mad_priv), DMA_FROM_DEVICE);
+free_mad_priv:
+	kfree(mad_priv);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/nldev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/nldev.c
@@ -511,7 +511,7 @@
 
 	/* In create_qp() port is not set yet */
 	if (qp->port && nla_put_u32(msg, RDMA_NLDEV_ATTR_PORT_INDEX, qp->port))
-		return -EINVAL;
+		return -EMSGSIZE;
 
 	ret = nla_put_u32(msg, RDMA_NLDEV_ATTR_RES_LQPN, qp->qp_num);
 	if (ret)
@@ -550,7 +550,7 @@
 	struct rdma_cm_id *cm_id = &id_priv->id;
 
 	if (port && port != cm_id->port_num)
-		return 0;
+		return -EAGAIN;
 
 	if (cm_id->port_num &&
 	    nla_put_u32(msg, RDMA_NLDEV_ATTR_PORT_INDEX, cm_id->port_num))
@@ -892,6 +892,8 @@
 	int ret = 0;
 
 	table_attr = nla_nest_start(msg, RDMA_NLDEV_ATTR_RES_QP);
+	if (!table_attr)
+		return -EMSGSIZE;
 
 	rt = &counter->device->res[RDMA_RESTRACK_QP];
 	xa_lock(&rt->xa);
@@ -2314,6 +2316,7 @@
 	},
 	[RDMA_NLDEV_CMD_SYS_SET] = {
 		.doit = nldev_set_sys_set_doit,
+		.flags = RDMA_NL_ADMIN_PERM,
 	},
 	[RDMA_NLDEV_CMD_STAT_SET] = {
 		.doit = nldev_stat_set_doit,
@@ -2349,7 +2352,7 @@
 	rdma_nl_register(RDMA_NL_NLDEV, nldev_cb_table);
 }
 
-void __exit nldev_exit(void)
+void nldev_exit(void)
 {
 	rdma_nl_unregister(RDMA_NL_NLDEV);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/peer_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/peer_mem.c
@@ -0,0 +1,689 @@
+// SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB
+/*
+ * Copyright (c) 2014-2020,  Mellanox Technologies. All rights reserved.
+ */
+
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_umem.h>
+#include <linux/sched/mm.h>
+#include "ib_peer_mem.h"
+
+static DEFINE_MUTEX(peer_memory_mutex);
+static LIST_HEAD(peer_memory_list);
+static struct kobject *peers_kobj;
+#define PEER_NO_INVALIDATION_ID U32_MAX
+
+static int ib_invalidate_peer_memory(void *reg_handle, u64 core_context);
+
+struct peer_mem_attribute {
+	struct attribute attr;
+	ssize_t (*show)(struct ib_peer_memory_client *ib_peer_client,
+			struct peer_mem_attribute *attr, char *buf);
+	ssize_t (*store)(struct ib_peer_memory_client *ib_peer_client,
+			 struct peer_mem_attribute *attr, const char *buf,
+			 size_t count);
+};
+#define PEER_ATTR_RO(_name)                                                    \
+	struct peer_mem_attribute peer_attr_ ## _name = __ATTR_RO(_name)
+
+static ssize_t version_show(struct ib_peer_memory_client *ib_peer_client,
+			    struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(buf, PAGE_SIZE, "%s\n",
+			 ib_peer_client->peer_mem->version);
+}
+static PEER_ATTR_RO(version);
+
+static ssize_t num_alloc_mrs_show(struct ib_peer_memory_client *ib_peer_client,
+				  struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(
+		buf, PAGE_SIZE, "%llu\n",
+		(u64)atomic64_read(&ib_peer_client->stats.num_alloc_mrs));
+}
+static PEER_ATTR_RO(num_alloc_mrs);
+
+static ssize_t
+num_dealloc_mrs_show(struct ib_peer_memory_client *ib_peer_client,
+		     struct peer_mem_attribute *attr, char *buf)
+
+{
+	return scnprintf(
+		buf, PAGE_SIZE, "%llu\n",
+		(u64)atomic64_read(&ib_peer_client->stats.num_dealloc_mrs));
+}
+static PEER_ATTR_RO(num_dealloc_mrs);
+
+static ssize_t num_reg_pages_show(struct ib_peer_memory_client *ib_peer_client,
+				  struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(
+		buf, PAGE_SIZE, "%llu\n",
+		(u64)atomic64_read(&ib_peer_client->stats.num_reg_pages));
+}
+static PEER_ATTR_RO(num_reg_pages);
+
+static ssize_t
+num_dereg_pages_show(struct ib_peer_memory_client *ib_peer_client,
+		     struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(
+		buf, PAGE_SIZE, "%llu\n",
+		(u64)atomic64_read(&ib_peer_client->stats.num_dereg_pages));
+}
+static PEER_ATTR_RO(num_dereg_pages);
+
+static ssize_t num_reg_bytes_show(struct ib_peer_memory_client *ib_peer_client,
+				  struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(
+		buf, PAGE_SIZE, "%llu\n",
+		(u64)atomic64_read(&ib_peer_client->stats.num_reg_bytes));
+}
+static PEER_ATTR_RO(num_reg_bytes);
+
+static ssize_t
+num_dereg_bytes_show(struct ib_peer_memory_client *ib_peer_client,
+		     struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(
+		buf, PAGE_SIZE, "%llu\n",
+		(u64)atomic64_read(&ib_peer_client->stats.num_dereg_bytes));
+}
+static PEER_ATTR_RO(num_dereg_bytes);
+
+static ssize_t
+num_free_callbacks_show(struct ib_peer_memory_client *ib_peer_client,
+			struct peer_mem_attribute *attr, char *buf)
+{
+	return scnprintf(buf, PAGE_SIZE, "%lu\n",
+			 ib_peer_client->stats.num_free_callbacks);
+}
+static PEER_ATTR_RO(num_free_callbacks);
+
+static struct attribute *peer_mem_attrs[] = {
+			&peer_attr_version.attr,
+			&peer_attr_num_alloc_mrs.attr,
+			&peer_attr_num_dealloc_mrs.attr,
+			&peer_attr_num_reg_pages.attr,
+			&peer_attr_num_dereg_pages.attr,
+			&peer_attr_num_reg_bytes.attr,
+			&peer_attr_num_dereg_bytes.attr,
+			&peer_attr_num_free_callbacks.attr,
+			NULL,
+};
+
+static const struct attribute_group peer_mem_attr_group = {
+	.attrs = peer_mem_attrs,
+};
+
+static ssize_t peer_attr_show(struct kobject *kobj, struct attribute *attr,
+			      char *buf)
+{
+	struct peer_mem_attribute *peer_attr =
+		container_of(attr, struct peer_mem_attribute, attr);
+
+	if (!peer_attr->show)
+		return -EIO;
+	return peer_attr->show(container_of(kobj, struct ib_peer_memory_client,
+					    kobj),
+			       peer_attr, buf);
+}
+
+static const struct sysfs_ops peer_mem_sysfs_ops = {
+	.show = peer_attr_show,
+};
+
+static void ib_peer_memory_client_release(struct kobject *kobj)
+{
+	struct ib_peer_memory_client *ib_peer_client =
+		container_of(kobj, struct ib_peer_memory_client, kobj);
+
+	kfree(ib_peer_client);
+}
+
+static struct kobj_type peer_mem_type = {
+	.sysfs_ops = &peer_mem_sysfs_ops,
+	.release = ib_peer_memory_client_release,
+};
+
+static int ib_memory_peer_check_mandatory(const struct peer_memory_client
+						     *peer_client)
+{
+#define PEER_MEM_MANDATORY_FUNC(x) {offsetof(struct peer_memory_client, x), #x}
+	int i;
+	static const struct {
+		size_t offset;
+		char *name;
+	} mandatory_table[] = {
+		PEER_MEM_MANDATORY_FUNC(acquire),
+		PEER_MEM_MANDATORY_FUNC(get_pages),
+		PEER_MEM_MANDATORY_FUNC(put_pages),
+		PEER_MEM_MANDATORY_FUNC(dma_map),
+		PEER_MEM_MANDATORY_FUNC(dma_unmap),
+	};
+
+	for (i = 0; i < ARRAY_SIZE(mandatory_table); ++i) {
+		if (!*(void **)((void *)peer_client +
+				mandatory_table[i].offset)) {
+			pr_err("Peer memory %s is missing mandatory function %s\n",
+			       peer_client->name, mandatory_table[i].name);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+void *
+ib_register_peer_memory_client(const struct peer_memory_client *peer_client,
+			       invalidate_peer_memory *invalidate_callback)
+{
+	struct ib_peer_memory_client *ib_peer_client;
+	int ret;
+
+	if (ib_memory_peer_check_mandatory(peer_client))
+		return NULL;
+
+	ib_peer_client = kzalloc(sizeof(*ib_peer_client), GFP_KERNEL);
+	if (!ib_peer_client)
+		return NULL;
+	kobject_init(&ib_peer_client->kobj, &peer_mem_type);
+	refcount_set(&ib_peer_client->usecnt, 1);
+	init_completion(&ib_peer_client->usecnt_zero);
+	ib_peer_client->peer_mem = peer_client;
+	xa_init_flags(&ib_peer_client->umem_xa, XA_FLAGS_ALLOC);
+
+	/*
+	 * If the peer wants the invalidation_callback then all memory users
+	 * linked to that peer must support invalidation.
+	 */
+	if (invalidate_callback) {
+		*invalidate_callback = ib_invalidate_peer_memory;
+		ib_peer_client->invalidation_required = true;
+	}
+
+	mutex_lock(&peer_memory_mutex);
+	if (!peers_kobj) {
+		/* Created under /sys/kernel/mm */
+		peers_kobj = kobject_create_and_add("memory_peers", mm_kobj);
+		if (!peers_kobj)
+			goto err_unlock;
+	}
+
+	ret = kobject_add(&ib_peer_client->kobj, peers_kobj, peer_client->name);
+	if (ret)
+		goto err_parent;
+
+	ret = sysfs_create_group(&ib_peer_client->kobj,
+				 &peer_mem_attr_group);
+	if (ret)
+		goto err_parent;
+	list_add_tail(&ib_peer_client->core_peer_list, &peer_memory_list);
+	mutex_unlock(&peer_memory_mutex);
+	return ib_peer_client;
+
+err_parent:
+	if (list_empty(&peer_memory_list)) {
+		kobject_put(peers_kobj);
+		peers_kobj = NULL;
+	}
+err_unlock:
+	mutex_unlock(&peer_memory_mutex);
+	kobject_put(&ib_peer_client->kobj);
+	return NULL;
+}
+EXPORT_SYMBOL(ib_register_peer_memory_client);
+
+void ib_unregister_peer_memory_client(void *reg_handle)
+{
+	struct ib_peer_memory_client *ib_peer_client = reg_handle;
+
+	mutex_lock(&peer_memory_mutex);
+	list_del(&ib_peer_client->core_peer_list);
+	if (list_empty(&peer_memory_list)) {
+		kobject_put(peers_kobj);
+		peers_kobj = NULL;
+	}
+	mutex_unlock(&peer_memory_mutex);
+
+	/*
+	 * Wait for all umems to be destroyed before returning. Once
+	 * ib_unregister_peer_memory_client() returns no umems will call any
+	 * peer_mem ops.
+	 */
+	if (refcount_dec_and_test(&ib_peer_client->usecnt))
+		complete(&ib_peer_client->usecnt_zero);
+	wait_for_completion(&ib_peer_client->usecnt_zero);
+
+	kobject_put(&ib_peer_client->kobj);
+}
+EXPORT_SYMBOL(ib_unregister_peer_memory_client);
+
+static struct ib_peer_memory_client *
+ib_get_peer_client(unsigned long addr, size_t size,
+		   unsigned long peer_mem_flags, void **peer_client_context)
+{
+	struct ib_peer_memory_client *ib_peer_client;
+	int ret = 0;
+
+	mutex_lock(&peer_memory_mutex);
+	list_for_each_entry(ib_peer_client, &peer_memory_list,
+			    core_peer_list) {
+		if (ib_peer_client->invalidation_required &&
+		    (!(peer_mem_flags & IB_PEER_MEM_INVAL_SUPP)))
+			continue;
+		ret = ib_peer_client->peer_mem->acquire(addr, size, NULL, NULL,
+							peer_client_context);
+		if (ret > 0) {
+			refcount_inc(&ib_peer_client->usecnt);
+			mutex_unlock(&peer_memory_mutex);
+			return ib_peer_client;
+		}
+	}
+	mutex_unlock(&peer_memory_mutex);
+	return NULL;
+}
+
+static void ib_put_peer_client(struct ib_peer_memory_client *ib_peer_client,
+			       void *peer_client_context)
+{
+	if (ib_peer_client->peer_mem->release)
+		ib_peer_client->peer_mem->release(peer_client_context);
+	if (refcount_dec_and_test(&ib_peer_client->usecnt))
+		complete(&ib_peer_client->usecnt_zero);
+}
+
+static void ib_peer_umem_kref_release(struct kref *kref)
+{
+	struct ib_umem_peer *umem_p =
+		container_of(kref, struct ib_umem_peer, kref);
+
+	mutex_destroy(&umem_p->mapping_lock);
+	kfree(umem_p);
+}
+
+static void ib_unmap_peer_client(struct ib_umem_peer *umem_p,
+				 enum ib_umem_mapped_state cur_state,
+				 enum ib_umem_mapped_state to_state)
+{
+	struct ib_peer_memory_client *ib_peer_client = umem_p->ib_peer_client;
+	const struct peer_memory_client *peer_mem = ib_peer_client->peer_mem;
+	struct ib_umem *umem = &umem_p->umem;
+
+	if (cur_state == UMEM_PEER_MAPPED &&
+	    (to_state == UMEM_PEER_UNMAPPED ||
+	     to_state == UMEM_PEER_INVALIDATED)) {
+		/*
+		 * In the invalidated state we will never touch the sg again,
+		 * but the client might, so fix it anyhow.
+		 */
+		if (umem_p->last_sg) {
+			umem_p->last_sg->length = umem_p->last_length;
+			sg_dma_len(umem_p->last_sg) = umem_p->last_dma_length;
+		}
+
+		if (umem_p->first_sg) {
+			umem_p->first_sg->dma_address =
+				umem_p->first_dma_address;
+			umem_p->first_sg->length = umem_p->first_length;
+			sg_dma_len(umem_p->first_sg) = umem_p->first_dma_length;
+		}
+
+		if (to_state == UMEM_PEER_UNMAPPED) {
+			peer_mem->dma_unmap(&umem_p->umem.sgt_append.sgt,
+					    umem_p->peer_client_context,
+					    umem_p->umem.ibdev->dma_device);
+			peer_mem->put_pages(&umem_p->umem.sgt_append.sgt,
+					    umem_p->peer_client_context);
+		}
+
+		memset(&umem->sgt_append.sgt, 0, sizeof(umem->sgt_append));
+		atomic64_inc(&ib_peer_client->stats.num_dealloc_mrs);
+	}
+
+	if ((cur_state == UMEM_PEER_MAPPED && to_state == UMEM_PEER_UNMAPPED) ||
+	    (cur_state == UMEM_PEER_INVALIDATED &&
+	     to_state == UMEM_PEER_UNMAPPED)) {
+		atomic64_add(umem->sgt_append.sgt.nents,
+			     &ib_peer_client->stats.num_dereg_pages);
+		atomic64_add(umem->length,
+			     &ib_peer_client->stats.num_dereg_bytes);
+	}
+	umem_p->mapped_state = to_state;
+}
+
+/*
+ * True if the client should do unmap itself after the invalidate callback
+ * returns. Clients operating in this mode need to use this locking pattern:
+ *
+ * client_invalidate:
+ *    mutex_lock(&client_lock)
+ *     invalidate_callback():
+ *       mutex_lock(mapping_lock)
+ *       mutex_unlock(mapping_lock)
+ *     client_dma_unmap()
+ *     client_put_pages()
+ *    mutex_unlock(&client_lock)
+ *
+ * ib_umem_stop_invalidation_notifier():
+ *  mutex_lock(mapping_lock)
+ *  mutex_unlock(mapping_lock)
+ *  peer_mem->dma_unmap():
+ *    mutex_lock(&client_lock)
+ *     client_dma_unmap()
+ *    mutex_unlock(&client_lock)
+ *  peer_mem->put_pages():
+ *    mutex_lock(&client_lock)
+ *     client_put_pages()
+ *    mutex_unlock(&client_lock)
+ *
+ * ib_peer_umem_release():
+ *  peer_mem->release():
+ *    mutex_lock(&client_lock)
+ *    mutex_unlock(&client_lock)
+ *
+ * Noting that dma_unmap/put_pages can be called even though invalidate has
+ * already done the unmap, and release() can be called concurrently with
+ * invalidate. The client must protect itself against these races.
+ */
+static bool ib_peer_unmap_on_invalidate(struct ib_umem_peer *umem_p)
+{
+	const struct peer_memory_client *peer_mem =
+		umem_p->ib_peer_client->peer_mem;
+	const struct peer_memory_client_ex *peer_mem_ex;
+
+	if (peer_mem->version[IB_PEER_MEMORY_VER_MAX - 1] == 0)
+		return false;
+	peer_mem_ex = container_of(peer_mem, const struct peer_memory_client_ex,
+				   client);
+	if (peer_mem_ex->ex_size <
+	    offsetofend(struct peer_memory_client_ex, flags))
+		return false;
+	return peer_mem_ex->flags & PEER_MEM_INVALIDATE_UNMAPS;
+}
+
+static int ib_invalidate_peer_memory(void *reg_handle, u64 core_context)
+{
+	struct ib_peer_memory_client *ib_peer_client = reg_handle;
+	struct ib_umem_peer *umem_p;
+
+	/*
+	 * The client is not required to fence against invalidation during
+	 * put_pages() as that would deadlock when we call put_pages() here.
+	 * Thus the core_context cannot be a umem pointer as we have no control
+	 * over the lifetime. Since we won't change the kABI for this to add a
+	 * proper kref, an xarray is used.
+	 */
+	xa_lock(&ib_peer_client->umem_xa);
+	ib_peer_client->stats.num_free_callbacks += 1;
+	umem_p = xa_load(&ib_peer_client->umem_xa, core_context);
+	if (!umem_p)
+		goto out_unlock;
+	kref_get(&umem_p->kref);
+	xa_unlock(&ib_peer_client->umem_xa);
+
+	mutex_lock(&umem_p->mapping_lock);
+	/*
+	 * For flows that require invalidation the invalidation_func should not
+	 * be NULL while the device can be doing DMA. The mapping_lock ensures
+	 * that the device is ready to receive an invalidation before one is
+	 * triggered here.
+	 */
+	if (umem_p->mapped_state == UMEM_PEER_MAPPED &&
+	    umem_p->invalidation_func)
+		umem_p->invalidation_func(&umem_p->umem,
+					  umem_p->invalidation_private);
+	if (ib_peer_unmap_on_invalidate(umem_p))
+		ib_unmap_peer_client(umem_p, umem_p->mapped_state,
+				     UMEM_PEER_INVALIDATED);
+	else
+		ib_unmap_peer_client(umem_p, umem_p->mapped_state,
+				     UMEM_PEER_UNMAPPED);
+	mutex_unlock(&umem_p->mapping_lock);
+	kref_put(&umem_p->kref, ib_peer_umem_kref_release);
+	return 0;
+
+out_unlock:
+	xa_unlock(&ib_peer_client->umem_xa);
+	return 0;
+}
+
+void ib_umem_activate_invalidation_notifier(struct ib_umem *umem,
+					    umem_invalidate_func_t func,
+					    void *priv)
+{
+	struct ib_umem_peer *umem_p =
+		container_of(umem, struct ib_umem_peer, umem);
+
+	if (WARN_ON(!umem->is_peer))
+		return;
+	if (umem_p->xa_id == PEER_NO_INVALIDATION_ID)
+		return;
+
+	umem_p->invalidation_func = func;
+	umem_p->invalidation_private = priv;
+	/* Pairs with the lock in ib_peer_umem_get() */
+	mutex_unlock(&umem_p->mapping_lock);
+
+	/* At this point func can be called asynchronously */
+}
+EXPORT_SYMBOL(ib_umem_activate_invalidation_notifier);
+
+/*
+ * Caller has blocked DMA and will no longer be able to handle invalidate
+ * callbacks. Callers using invalidation must call this function before calling
+ * ib_peer_umem_release(). ib_umem_activate_invalidation_notifier() is optional
+ * before doing this.
+ */
+void ib_umem_stop_invalidation_notifier(struct ib_umem *umem)
+{
+	struct ib_umem_peer *umem_p =
+		container_of(umem, struct ib_umem_peer, umem);
+	bool unmap_on_invalidate = ib_peer_unmap_on_invalidate(umem_p);
+	enum ib_umem_mapped_state cur_state;
+
+	if (umem_p->invalidation_func) {
+		mutex_lock(&umem_p->mapping_lock);
+		umem_p->invalidation_func = NULL;
+	} else if (umem_p->xa_id != PEER_NO_INVALIDATION_ID) {
+		mutex_lock(&umem_p->mapping_lock);
+	} else {
+		/*
+		 * Haven't called ib_umem_activate_invalidation_notifier() yet,
+		 * still have the lock
+		 */
+	}
+
+	if (!unmap_on_invalidate) {
+		ib_unmap_peer_client(umem_p, umem_p->mapped_state,
+				     UMEM_PEER_UNMAPPED);
+	} else {
+		/* Block ib_invalidate_peer_memory() */
+		cur_state = umem_p->mapped_state;
+		umem_p->mapped_state = UMEM_PEER_UNMAPPED;
+	}
+	mutex_unlock(&umem_p->mapping_lock);
+
+	if (unmap_on_invalidate)
+		ib_unmap_peer_client(umem_p, cur_state, UMEM_PEER_UNMAPPED);
+
+}
+EXPORT_SYMBOL(ib_umem_stop_invalidation_notifier);
+
+static void fix_peer_sgls(struct ib_umem_peer *umem_p, unsigned long peer_page_size)
+{
+	struct ib_umem *umem = &umem_p->umem;
+	struct scatterlist *sg;
+	int i;
+
+	for_each_sg(umem_p->umem.sgt_append.sgt.sgl, sg,
+		    umem_p->umem.sgt_append.sgt.nents, i) {
+		if (i == 0) {
+			unsigned long offset;
+
+			umem_p->first_sg = sg;
+			umem_p->first_dma_address = sg->dma_address;
+			umem_p->first_dma_length = sg_dma_len(sg);
+			umem_p->first_length = sg->length;
+
+			offset = ALIGN_DOWN(umem->address, PAGE_SIZE) -
+				 ALIGN_DOWN(umem->address, peer_page_size);
+			sg->dma_address += offset;
+			sg_dma_len(sg) -= offset;
+			sg->length -= offset;
+		}
+
+		if (i == umem_p->umem.sgt_append.sgt.nents - 1) {
+			unsigned long trim;
+
+			umem_p->last_sg = sg;
+			umem_p->last_dma_length = sg_dma_len(sg);
+			umem_p->last_length = sg->length;
+
+			trim = ALIGN(umem->address + umem->length,
+				     peer_page_size) -
+			       ALIGN(umem->address + umem->length, PAGE_SIZE);
+			sg_dma_len(sg) -= trim;
+			sg->length -= trim;
+		}
+	}
+}
+
+struct ib_umem *ib_peer_umem_get(struct ib_umem *old_umem, int old_ret,
+				 unsigned long peer_mem_flags)
+{
+	struct ib_peer_memory_client *ib_peer_client;
+	unsigned long peer_page_size;
+	void *peer_client_context;
+	struct ib_umem_peer *umem_p;
+	int ret;
+
+	ib_peer_client =
+		ib_get_peer_client(old_umem->address, old_umem->length,
+				   peer_mem_flags, &peer_client_context);
+	if (!ib_peer_client)
+		return ERR_PTR(old_ret);
+
+	umem_p = kzalloc(sizeof(*umem_p), GFP_KERNEL);
+	if (!umem_p) {
+		ret = -ENOMEM;
+		goto err_client;
+	}
+
+	kref_init(&umem_p->kref);
+	umem_p->umem = *old_umem;
+	memset(&umem_p->umem.sgt_append.sgt, 0, sizeof(umem_p->umem.sgt_append));
+	umem_p->umem.is_peer = 1;
+	umem_p->ib_peer_client = ib_peer_client;
+	umem_p->peer_client_context = peer_client_context;
+	mutex_init(&umem_p->mapping_lock);
+	umem_p->xa_id = PEER_NO_INVALIDATION_ID;
+
+	mutex_lock(&umem_p->mapping_lock);
+	if (ib_peer_client->invalidation_required) {
+		ret = xa_alloc_cyclic(&ib_peer_client->umem_xa, &umem_p->xa_id,
+				      umem_p,
+				      XA_LIMIT(0, PEER_NO_INVALIDATION_ID - 1),
+				      &ib_peer_client->xa_cyclic_next,
+				      GFP_KERNEL);
+		if (ret < 0)
+			goto err_umem;
+	}
+
+	/*
+	 * We always request write permissions to the pages, to force breaking
+	 * of any CoW during the registration of the MR. For read-only MRs we
+	 * use the "force" flag to indicate that CoW breaking is required but
+	 * the registration should not fail if referencing read-only areas.
+	 */
+	ret = ib_peer_client->peer_mem->get_pages(umem_p->umem.address,
+						  umem_p->umem.length, 1,
+						  !umem_p->umem.writable, NULL,
+						  peer_client_context,
+						  umem_p->xa_id);
+	if (ret)
+		goto err_xa;
+
+	ret = ib_peer_client->peer_mem->dma_map(&umem_p->umem.sgt_append.sgt,
+						peer_client_context,
+						umem_p->umem.ibdev->dma_device,
+						0, &umem_p->umem.sgt_append.sgt.nents);
+	if (ret)
+		goto err_pages;
+
+	peer_page_size = ib_peer_client->peer_mem->get_page_size(peer_client_context);
+	if (peer_page_size != PAGE_SIZE)
+		fix_peer_sgls(umem_p, peer_page_size);
+
+	umem_p->mapped_state = UMEM_PEER_MAPPED;
+	atomic64_add(umem_p->umem.sgt_append.sgt.nents, &ib_peer_client->stats.num_reg_pages);
+	atomic64_add(umem_p->umem.length, &ib_peer_client->stats.num_reg_bytes);
+	atomic64_inc(&ib_peer_client->stats.num_alloc_mrs);
+
+	/*
+	 * If invalidation is allowed then the caller must call
+	 * ib_umem_activate_invalidation_notifier() or ib_peer_umem_release() to
+	 * unlock this mutex. This call should be done after the last read to
+	 * sg_head, once the caller is ready for the invalidation function to be
+	 * called.
+	 */
+	if (umem_p->xa_id == PEER_NO_INVALIDATION_ID)
+		mutex_unlock(&umem_p->mapping_lock);
+
+	/*
+	 * On success the old umem is replaced with the new, larger, allocation
+	 */
+	kfree(old_umem);
+	return &umem_p->umem;
+
+err_pages:
+	ib_peer_client->peer_mem->put_pages(&umem_p->umem.sgt_append.sgt,
+					    umem_p->peer_client_context);
+err_xa:
+	if (umem_p->xa_id != PEER_NO_INVALIDATION_ID)
+		xa_erase(&umem_p->ib_peer_client->umem_xa, umem_p->xa_id);
+err_umem:
+	mutex_unlock(&umem_p->mapping_lock);
+	kref_put(&umem_p->kref, ib_peer_umem_kref_release);
+err_client:
+	ib_put_peer_client(ib_peer_client, peer_client_context);
+	return ERR_PTR(ret);
+}
+
+void ib_peer_umem_release(struct ib_umem *umem)
+{
+	struct ib_umem_peer *umem_p =
+		container_of(umem, struct ib_umem_peer, umem);
+
+	/*
+	 * If ib_umem_activate_invalidation_notifier() is called then
+	 * ib_umem_stop_invalidation_notifier() must be called before release.
+	 */
+	WARN_ON(umem_p->invalidation_func);
+
+	/* For no invalidation cases, make sure it is unmapped */
+	ib_unmap_peer_client(umem_p, umem_p->mapped_state, UMEM_PEER_UNMAPPED);
+
+	if (umem_p->xa_id != PEER_NO_INVALIDATION_ID)
+		xa_erase(&umem_p->ib_peer_client->umem_xa, umem_p->xa_id);
+	ib_put_peer_client(umem_p->ib_peer_client, umem_p->peer_client_context);
+	umem_p->ib_peer_client = NULL;
+
+	/* Must match ib_umem_release() */
+	atomic64_sub(ib_umem_num_pages(umem), &umem->owning_mm->pinned_vm);
+	mmdrop(umem->owning_mm);
+
+	kref_put(&umem_p->kref, ib_peer_umem_kref_release);
+}
+
+/* Use it like this:
+struct peer_memory_client_ex peer_memory_test = {
+	.client = {
+		.version = "1.0",
+		.version[IB_PEER_MEMORY_VER_MAX-1] = 1,
+	},
+	.ex_size = sizeof(struct peer_memory_client_ex),
+	.flags = PEER_MEM_INVALIDATE_UNMAPS,
+};
+*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/restrack.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/restrack.c
@@ -37,22 +37,6 @@
 	return 0;
 }
 
-static const char *type2str(enum rdma_restrack_type type)
-{
-	static const char * const names[RDMA_RESTRACK_MAX] = {
-		[RDMA_RESTRACK_PD] = "PD",
-		[RDMA_RESTRACK_CQ] = "CQ",
-		[RDMA_RESTRACK_QP] = "QP",
-		[RDMA_RESTRACK_CM_ID] = "CM_ID",
-		[RDMA_RESTRACK_MR] = "MR",
-		[RDMA_RESTRACK_CTX] = "CTX",
-		[RDMA_RESTRACK_COUNTER] = "COUNTER",
-		[RDMA_RESTRACK_SRQ] = "SRQ",
-	};
-
-	return names[type];
-};
-
 /**
  * rdma_restrack_clean() - clean resource tracking
  * @dev:  IB device
@@ -60,47 +44,14 @@
 void rdma_restrack_clean(struct ib_device *dev)
 {
 	struct rdma_restrack_root *rt = dev->res;
-	struct rdma_restrack_entry *e;
-	char buf[TASK_COMM_LEN];
-	bool found = false;
-	const char *owner;
 	int i;
 
 	for (i = 0 ; i < RDMA_RESTRACK_MAX; i++) {
 		struct xarray *xa = &dev->res[i].xa;
 
-		if (!xa_empty(xa)) {
-			unsigned long index;
-
-			if (!found) {
-				pr_err("restrack: %s", CUT_HERE);
-				dev_err(&dev->dev, "BUG: RESTRACK detected leak of resources\n");
-			}
-			xa_for_each(xa, index, e) {
-				if (rdma_is_kernel_res(e)) {
-					owner = e->kern_name;
-				} else {
-					/*
-					 * There is no need to call get_task_struct here,
-					 * because we can be here only if there are more
-					 * get_task_struct() call than put_task_struct().
-					 */
-					get_task_comm(buf, e->task);
-					owner = buf;
-				}
-
-				pr_err("restrack: %s %s object allocated by %s is not freed\n",
-				       rdma_is_kernel_res(e) ? "Kernel" :
-							       "User",
-				       type2str(e->type), owner);
-			}
-			found = true;
-		}
+		WARN_ON(!xa_empty(xa));
 		xa_destroy(xa);
 	}
-	if (found)
-		pr_err("restrack: %s", CUT_HERE);
-
 	kfree(rt);
 }
 
@@ -343,8 +294,6 @@
 	rt = &dev->res[res->type];
 
 	old = xa_erase(&rt->xa, res->id);
-	if (res->type == RDMA_RESTRACK_MR)
-		return;
 	WARN_ON(old != res);
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/sa_query.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/sa_query.c
@@ -2132,7 +2132,9 @@
 	s = rdma_start_port(device);
 	e = rdma_end_port(device);
 
-	sa_dev = kzalloc(struct_size(sa_dev, port, e - s + 1), GFP_KERNEL);
+	sa_dev = kzalloc(struct_size(sa_dev, port,
+				     size_add(size_sub(e, s), 1)),
+			 GFP_KERNEL);
 	if (!sa_dev)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/sysfs.c
@@ -757,7 +757,7 @@
 	if (port->hw_stats_data)
 		kfree(port->hw_stats_data->stats);
 	kfree(port->hw_stats_data);
-	kfree(port);
+	kvfree(port);
 }
 
 static void ib_port_gid_attr_release(struct kobject *kobj)
@@ -902,7 +902,7 @@
 	 * Two extra attribue elements here, one for the lifespan entry and
 	 * one to NULL terminate the list for the sysfs core code
 	 */
-	data = kzalloc(struct_size(data, attrs, stats->num_counters + 1),
+	data = kzalloc(struct_size(data, attrs, size_add(stats->num_counters, 1)),
 		       GFP_KERNEL);
 	if (!data)
 		goto err_free_stats;
@@ -976,6 +976,7 @@
 	for (i = 0; i != ARRAY_SIZE(ibdev->groups); i++)
 		if (!ibdev->groups[i]) {
 			ibdev->groups[i] = &data->group;
+			ibdev->hw_stats_attr_index = i;
 			return 0;
 		}
 	WARN(true, "struct ib_device->groups is too small");
@@ -1001,7 +1002,7 @@
 	 * Two extra attribue elements here, one for the lifespan entry and
 	 * one to NULL terminate the list for the sysfs core code
 	 */
-	data = kzalloc(struct_size(data, attrs, stats->num_counters + 1),
+	data = kzalloc(struct_size(data, attrs, size_add(stats->num_counters, 1)),
 		       GFP_KERNEL);
 	if (!data)
 		goto err_free_stats;
@@ -1125,7 +1126,7 @@
 	int ret;
 
 	gid_attr_group = kzalloc(struct_size(gid_attr_group, attrs_list,
-					     attr->gid_tbl_len * 2),
+					     size_mul(attr->gid_tbl_len, 2)),
 				 GFP_KERNEL);
 	if (!gid_attr_group)
 		return -ENOMEM;
@@ -1189,15 +1190,18 @@
 	struct ib_port *p;
 	int ret;
 
-	p = kzalloc(struct_size(p, attrs_list,
-				attr->gid_tbl_len + attr->pkey_tbl_len),
-		    GFP_KERNEL);
+	p = kvzalloc(struct_size(p, attrs_list,
+				size_add(attr->gid_tbl_len, attr->pkey_tbl_len)),
+		     GFP_KERNEL);
 	if (!p)
 		return ERR_PTR(-ENOMEM);
 	p->ibdev = device;
 	p->port_num = port_num;
 	kobject_init(&p->kobj, &port_type);
 
+	if (device->port_data && is_full_dev)
+		device->port_data[port_num].sysfs = p;
+
 	cur_group = p->groups_list;
 	ret = alloc_port_table_group("gids", &p->groups[0], p->attrs_list,
 				     attr->gid_tbl_len, show_port_gid);
@@ -1243,9 +1247,6 @@
 	}
 
 	list_add_tail(&p->kobj.entry, &coredev->port_list);
-	if (device->port_data && is_full_dev)
-		device->port_data[port_num].sysfs = p;
-
 	return p;
 
 err_groups:
@@ -1253,6 +1254,8 @@
 err_del:
 	kobject_del(&p->kobj);
 err_put:
+	if (device->port_data && is_full_dev)
+		device->port_data[port_num].sysfs = NULL;
 	kobject_put(&p->kobj);
 	return ERR_PTR(ret);
 }
@@ -1261,14 +1264,17 @@
 {
 	bool is_full_dev = &port->ibdev->coredev == coredev;
 
-	if (port->ibdev->port_data &&
-	    port->ibdev->port_data[port->port_num].sysfs == port)
-		port->ibdev->port_data[port->port_num].sysfs = NULL;
 	list_del(&port->kobj.entry);
 	if (is_full_dev)
 		sysfs_remove_groups(&port->kobj, port->ibdev->ops.port_groups);
+
 	sysfs_remove_groups(&port->kobj, port->groups_list);
 	kobject_del(&port->kobj);
+
+	if (port->ibdev->port_data &&
+	    port->ibdev->port_data[port->port_num].sysfs == port)
+		port->ibdev->port_data[port->port_num].sysfs = NULL;
+
 	kobject_put(&port->kobj);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/ucma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/ucma.c
@@ -95,6 +95,7 @@
 	u64			uid;
 
 	struct list_head	list;
+	struct list_head	mc_list;
 	struct work_struct	close_work;
 };
 
@@ -105,6 +106,7 @@
 
 	u64			uid;
 	u8			join_state;
+	struct list_head	list;
 	struct sockaddr_storage	addr;
 };
 
@@ -198,6 +200,7 @@
 
 	INIT_WORK(&ctx->close_work, ucma_close_id);
 	init_completion(&ctx->comp);
+	INIT_LIST_HEAD(&ctx->mc_list);
 	/* So list_del() will work if we don't do ucma_finish_ctx() */
 	INIT_LIST_HEAD(&ctx->list);
 	ctx->file = file;
@@ -484,19 +487,19 @@
 
 static void ucma_cleanup_multicast(struct ucma_context *ctx)
 {
-	struct ucma_multicast *mc;
-	unsigned long index;
+	struct ucma_multicast *mc, *tmp;
 
-	xa_for_each(&multicast_table, index, mc) {
-		if (mc->ctx != ctx)
-			continue;
+	xa_lock(&multicast_table);
+	list_for_each_entry_safe(mc, tmp, &ctx->mc_list, list) {
+		list_del(&mc->list);
 		/*
 		 * At this point mc->ctx->ref is 0 so the mc cannot leave the
 		 * lock on the reader and this is enough serialization
 		 */
-		xa_erase(&multicast_table, index);
+		__xa_erase(&multicast_table, mc->id);
 		kfree(mc);
 	}
+	xa_unlock(&multicast_table);
 }
 
 static void ucma_cleanup_mc_events(struct ucma_multicast *mc)
@@ -1469,12 +1472,16 @@
 	mc->uid = cmd->uid;
 	memcpy(&mc->addr, addr, cmd->addr_size);
 
-	if (xa_alloc(&multicast_table, &mc->id, NULL, xa_limit_32b,
+	xa_lock(&multicast_table);
+	if (__xa_alloc(&multicast_table, &mc->id, NULL, xa_limit_32b,
 		     GFP_KERNEL)) {
 		ret = -ENOMEM;
 		goto err_free_mc;
 	}
 
+	list_add_tail(&mc->list, &ctx->mc_list);
+	xa_unlock(&multicast_table);
+
 	mutex_lock(&ctx->mutex);
 	ret = rdma_join_multicast(ctx->cm_id, (struct sockaddr *)&mc->addr,
 				  join_state, mc);
@@ -1500,8 +1507,11 @@
 	mutex_unlock(&ctx->mutex);
 	ucma_cleanup_mc_events(mc);
 err_xa_erase:
-	xa_erase(&multicast_table, mc->id);
+	xa_lock(&multicast_table);
+	list_del(&mc->list);
+	__xa_erase(&multicast_table, mc->id);
 err_free_mc:
+	xa_unlock(&multicast_table);
 	kfree(mc);
 err_put_ctx:
 	ucma_put_ctx(ctx);
@@ -1569,15 +1579,17 @@
 		mc = ERR_PTR(-EINVAL);
 	else if (!refcount_inc_not_zero(&mc->ctx->ref))
 		mc = ERR_PTR(-ENXIO);
-	else
-		__xa_erase(&multicast_table, mc->id);
-	xa_unlock(&multicast_table);
 
 	if (IS_ERR(mc)) {
+		xa_unlock(&multicast_table);
 		ret = PTR_ERR(mc);
 		goto out;
 	}
 
+	list_del(&mc->list);
+	__xa_erase(&multicast_table, mc->id);
+	xa_unlock(&multicast_table);
+
 	mutex_lock(&mc->ctx->mutex);
 	rdma_leave_multicast(mc->ctx->cm_id, (struct sockaddr *) &mc->addr);
 	mutex_unlock(&mc->ctx->mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/umem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/umem.c
@@ -45,6 +45,8 @@
 
 #include "uverbs.h"
 
+#include "ib_peer_mem.h"
+
 static void __ib_umem_release(struct ib_device *dev, struct ib_umem *umem, int dirty)
 {
 	bool make_dirty = umem->writable && dirty;
@@ -85,6 +87,8 @@
 	dma_addr_t mask;
 	int i;
 
+	umem->iova = va = virt;
+
 	if (umem->is_odp) {
 		unsigned int page_size = BIT(to_ib_umem_odp(umem)->page_shift);
 
@@ -94,13 +98,6 @@
 		return page_size;
 	}
 
-	/* rdma_for_each_block() has a bug if the page size is smaller than the
-	 * page size used to build the umem. For now prevent smaller page sizes
-	 * from being returned.
-	 */
-	pgsz_bitmap &= GENMASK(BITS_PER_LONG - 1, PAGE_SHIFT);
-
-	umem->iova = va = virt;
 	/* The best result is the smallest page size that results in the minimum
 	 * number of required pages. Compute the largest page size that could
 	 * work based on VA address bits that don't change.
@@ -137,15 +134,17 @@
 EXPORT_SYMBOL(ib_umem_find_best_pgsz);
 
 /**
- * ib_umem_get - Pin and DMA map userspace memory.
+ * __ib_umem_get - Pin and DMA map userspace memory.
  *
  * @device: IB device to connect UMEM
  * @addr: userspace virtual address to start at
  * @size: length of region to pin
  * @access: IB_ACCESS_xxx flags for memory being pinned
+ * @peer_mem_flags: IB_PEER_MEM_xxx flags for memory being used
  */
-struct ib_umem *ib_umem_get(struct ib_device *device, unsigned long addr,
-			    size_t size, int access)
+static struct ib_umem *__ib_umem_get(struct ib_device *device,
+				    unsigned long addr, size_t size, int access,
+				    unsigned long peer_mem_flags)
 {
 	struct ib_umem *umem;
 	struct page **page_list;
@@ -248,6 +247,26 @@
 
 umem_release:
 	__ib_umem_release(device, umem, 0);
+
+	/*
+	 * If the address belongs to peer memory client, then the first
+	 * call to get_user_pages will fail. In this case, try to get
+	 * these pages from the peers.
+	 */
+	//FIXME: this placement is horrible
+	if (ret < 0 && peer_mem_flags & IB_PEER_MEM_ALLOW) {
+		struct ib_umem *new_umem;
+
+		new_umem = ib_peer_umem_get(umem, ret, peer_mem_flags);
+		if (IS_ERR(new_umem)) {
+			ret = PTR_ERR(new_umem);
+			goto vma;
+		}
+		umem = new_umem;
+		ret = 0;
+		goto out;
+	}
+vma:
 	atomic64_sub(ib_umem_num_pages(umem), &mm->pinned_vm);
 out:
 	free_page((unsigned long) page_list);
@@ -258,8 +277,23 @@
 	}
 	return ret ? ERR_PTR(ret) : umem;
 }
+
+struct ib_umem *ib_umem_get(struct ib_device *device, unsigned long addr,
+			    size_t size, int access)
+{
+	return __ib_umem_get(device, addr, size, access, 0);
+}
 EXPORT_SYMBOL(ib_umem_get);
 
+struct ib_umem *ib_umem_get_peer(struct ib_device *device, unsigned long addr,
+				 size_t size, int access,
+				 unsigned long peer_mem_flags)
+{
+	return __ib_umem_get(device, addr, size, access,
+			     IB_PEER_MEM_ALLOW | peer_mem_flags);
+}
+EXPORT_SYMBOL(ib_umem_get_peer);
+
 /**
  * ib_umem_release - release memory pinned with ib_umem_get
  * @umem: umem struct to release
@@ -273,6 +307,8 @@
 	if (umem->is_odp)
 		return ib_umem_odp_release(to_ib_umem_odp(umem));
 
+	if (umem->is_peer)
+		return ib_peer_umem_release(umem);
 	__ib_umem_release(umem->ibdev, umem, 1);
 
 	atomic64_sub(ib_umem_num_pages(umem), &umem->owning_mm->pinned_vm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/umem_odp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/umem_odp.c
@@ -463,7 +463,7 @@
 		mutex_unlock(&umem_odp->umem_mutex);
 
 out_put_mm:
-	mmput(owning_mm);
+	mmput_async(owning_mm);
 out_put_task:
 	if (owning_process)
 		put_task_struct(owning_process);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/user_mad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/user_mad.c
@@ -63,6 +63,8 @@
 MODULE_DESCRIPTION("InfiniBand userspace MAD packet access");
 MODULE_LICENSE("Dual BSD/GPL");
 
+#define MAX_UMAD_RECV_LIST_SIZE 200000
+
 enum {
 	IB_UMAD_MAX_PORTS  = RDMA_MAX_PORTS,
 	IB_UMAD_MAX_AGENTS = 32,
@@ -113,6 +115,7 @@
 	struct mutex		mutex;
 	struct ib_umad_port    *port;
 	struct list_head	recv_list;
+	atomic_t		recv_list_size;
 	struct list_head	send_list;
 	struct list_head	port_list;
 	spinlock_t		send_lock;
@@ -131,6 +134,11 @@
 	struct ib_user_mad mad;
 };
 
+struct ib_rmpp_mad_hdr {
+	struct ib_mad_hdr	mad_hdr;
+	struct ib_rmpp_hdr      rmpp_hdr;
+} __packed;
+
 #define CREATE_TRACE_POINTS
 #include <trace/events/ib_umad.h>
 
@@ -175,24 +183,28 @@
 	return file->agents_dead ? NULL : file->agent[id];
 }
 
-static int queue_packet(struct ib_umad_file *file,
-			struct ib_mad_agent *agent,
-			struct ib_umad_packet *packet)
+static int queue_packet(struct ib_umad_file *file, struct ib_mad_agent *agent,
+			struct ib_umad_packet *packet, bool is_recv_mad)
 {
 	int ret = 1;
 
 	mutex_lock(&file->mutex);
 
+	if (is_recv_mad &&
+	    atomic_read(&file->recv_list_size) > MAX_UMAD_RECV_LIST_SIZE)
+		goto unlock;
+
 	for (packet->mad.hdr.id = 0;
 	     packet->mad.hdr.id < IB_UMAD_MAX_AGENTS;
 	     packet->mad.hdr.id++)
 		if (agent == __get_agent(file, packet->mad.hdr.id)) {
 			list_add_tail(&packet->list, &file->recv_list);
+			atomic_inc(&file->recv_list_size);
 			wake_up_interruptible(&file->recv_wait);
 			ret = 0;
 			break;
 		}
-
+unlock:
 	mutex_unlock(&file->mutex);
 
 	return ret;
@@ -219,7 +231,7 @@
 	if (send_wc->status == IB_WC_RESP_TIMEOUT_ERR) {
 		packet->length = IB_MGMT_MAD_HDR;
 		packet->mad.hdr.status = ETIMEDOUT;
-		if (!queue_packet(file, agent, packet))
+		if (!queue_packet(file, agent, packet, false))
 			return;
 	}
 	kfree(packet);
@@ -279,7 +291,7 @@
 		rdma_destroy_ah_attr(&ah_attr);
 	}
 
-	if (queue_packet(file, agent, packet))
+	if (queue_packet(file, agent, packet, true))
 		goto err2;
 	return;
 
@@ -404,6 +416,7 @@
 
 	packet = list_entry(file->recv_list.next, struct ib_umad_packet, list);
 	list_del(&packet->list);
+	atomic_dec(&file->recv_list_size);
 
 	mutex_unlock(&file->mutex);
 
@@ -416,6 +429,7 @@
 		/* Requeue packet */
 		mutex_lock(&file->mutex);
 		list_add(&packet->list, &file->recv_list);
+		atomic_inc(&file->recv_list_size);
 		mutex_unlock(&file->mutex);
 	} else {
 		if (packet->recv_wc)
@@ -494,11 +508,11 @@
 			     size_t count, loff_t *pos)
 {
 	struct ib_umad_file *file = filp->private_data;
+	struct ib_rmpp_mad_hdr *rmpp_mad_hdr;
 	struct ib_umad_packet *packet;
 	struct ib_mad_agent *agent;
 	struct rdma_ah_attr ah_attr;
 	struct ib_ah *ah;
-	struct ib_rmpp_mad *rmpp_mad;
 	__be64 *tid;
 	int ret, data_len, hdr_len, copy_offset, rmpp_active;
 	u8 base_version;
@@ -506,7 +520,7 @@
 	if (count < hdr_size(file) + IB_MGMT_RMPP_HDR)
 		return -EINVAL;
 
-	packet = kzalloc(sizeof *packet + IB_MGMT_RMPP_HDR, GFP_KERNEL);
+	packet = kzalloc(sizeof(*packet) + IB_MGMT_RMPP_HDR, GFP_KERNEL);
 	if (!packet)
 		return -ENOMEM;
 
@@ -560,13 +574,13 @@
 		goto err_up;
 	}
 
-	rmpp_mad = (struct ib_rmpp_mad *) packet->mad.data;
-	hdr_len = ib_get_mad_data_offset(rmpp_mad->mad_hdr.mgmt_class);
+	rmpp_mad_hdr = (struct ib_rmpp_mad_hdr *)packet->mad.data;
+	hdr_len = ib_get_mad_data_offset(rmpp_mad_hdr->mad_hdr.mgmt_class);
 
-	if (ib_is_mad_class_rmpp(rmpp_mad->mad_hdr.mgmt_class)
+	if (ib_is_mad_class_rmpp(rmpp_mad_hdr->mad_hdr.mgmt_class)
 	    && ib_mad_kernel_rmpp_agent(agent)) {
 		copy_offset = IB_MGMT_RMPP_HDR;
-		rmpp_active = ib_get_rmpp_flags(&rmpp_mad->rmpp_hdr) &
+		rmpp_active = ib_get_rmpp_flags(&rmpp_mad_hdr->rmpp_hdr) &
 						IB_MGMT_RMPP_FLAG_ACTIVE;
 	} else {
 		copy_offset = IB_MGMT_MAD_HDR;
@@ -615,12 +629,12 @@
 		tid = &((struct ib_mad_hdr *) packet->msg->mad)->tid;
 		*tid = cpu_to_be64(((u64) agent->hi_tid) << 32 |
 				   (be64_to_cpup(tid) & 0xffffffff));
-		rmpp_mad->mad_hdr.tid = *tid;
+		rmpp_mad_hdr->mad_hdr.tid = *tid;
 	}
 
 	if (!ib_mad_kernel_rmpp_agent(agent)
-	   && ib_is_mad_class_rmpp(rmpp_mad->mad_hdr.mgmt_class)
-	   && (ib_get_rmpp_flags(&rmpp_mad->rmpp_hdr) & IB_MGMT_RMPP_FLAG_ACTIVE)) {
+	    && ib_is_mad_class_rmpp(rmpp_mad_hdr->mad_hdr.mgmt_class)
+	    && (ib_get_rmpp_flags(&rmpp_mad_hdr->rmpp_hdr) & IB_MGMT_RMPP_FLAG_ACTIVE)) {
 		spin_lock_irq(&file->send_lock);
 		list_add_tail(&packet->list, &file->send_list);
 		spin_unlock_irq(&file->send_lock);
@@ -1373,7 +1387,9 @@
 	s = rdma_start_port(device);
 	e = rdma_end_port(device);
 
-	umad_dev = kzalloc(struct_size(umad_dev, ports, e - s + 1), GFP_KERNEL);
+	umad_dev = kzalloc(struct_size(umad_dev, ports,
+				       size_add(size_sub(e, s), 1)),
+			   GFP_KERNEL);
 	if (!umad_dev)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/uverbs_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/uverbs_cmd.c
@@ -161,7 +161,7 @@
 {
 	const void __user *res = iter->cur;
 
-	if (iter->cur + len > iter->end)
+	if (len > iter->end - iter->cur)
 		return (void __force __user *)ERR_PTR(-ENOSPC);
 	iter->cur += len;
 	return res;
@@ -739,6 +739,7 @@
 	mr->uobject = uobj;
 	atomic_inc(&pd->usecnt);
 	mr->iova = cmd.hca_va;
+	mr->length = cmd.length;
 
 	rdma_restrack_new(&mr->res, RDMA_RESTRACK_MR);
 	rdma_restrack_set_name(&mr->res, NULL);
@@ -837,11 +838,8 @@
 		new_mr->device = new_pd->device;
 		new_mr->pd = new_pd;
 		new_mr->type = IB_MR_TYPE_USER;
-		new_mr->dm = NULL;
-		new_mr->sig_attrs = NULL;
 		new_mr->uobject = uobj;
 		atomic_inc(&new_pd->usecnt);
-		new_mr->iova = cmd.hca_va;
 		new_uobj->object = new_mr;
 
 		rdma_restrack_new(&new_mr->res, RDMA_RESTRACK_MR);
@@ -864,8 +862,10 @@
 			mr->pd = new_pd;
 			atomic_inc(&new_pd->usecnt);
 		}
-		if (cmd.flags & IB_MR_REREG_TRANS)
+		if (cmd.flags & IB_MR_REREG_TRANS) {
 			mr->iova = cmd.hca_va;
+			mr->length = cmd.length;
+		}
 	}
 
 	memset(&resp, 0, sizeof(resp));
@@ -1851,8 +1851,13 @@
 		attr->path_mtu = cmd->base.path_mtu;
 	if (cmd->base.attr_mask & IB_QP_PATH_MIG_STATE)
 		attr->path_mig_state = cmd->base.path_mig_state;
-	if (cmd->base.attr_mask & IB_QP_QKEY)
+	if (cmd->base.attr_mask & IB_QP_QKEY) {
+		if (cmd->base.qkey & IB_QP_SET_QKEY && !capable(CAP_NET_RAW)) {
+			ret = -EPERM;
+			goto release_qp;
+		}
 		attr->qkey = cmd->base.qkey;
+	}
 	if (cmd->base.attr_mask & IB_QP_RQ_PSN)
 		attr->rq_psn = cmd->base.rq_psn;
 	if (cmd->base.attr_mask & IB_QP_SQ_PSN)
@@ -2005,11 +2010,13 @@
 	ret = uverbs_request_start(attrs, &iter, &cmd, sizeof(cmd));
 	if (ret)
 		return ret;
-	wqes = uverbs_request_next_ptr(&iter, cmd.wqe_size * cmd.wr_count);
+	wqes = uverbs_request_next_ptr(&iter, size_mul(cmd.wqe_size,
+						       cmd.wr_count));
 	if (IS_ERR(wqes))
 		return PTR_ERR(wqes);
-	sgls = uverbs_request_next_ptr(
-		&iter, cmd.sge_count * sizeof(struct ib_uverbs_sge));
+	sgls = uverbs_request_next_ptr(&iter,
+				       size_mul(cmd.sge_count,
+						sizeof(struct ib_uverbs_sge)));
 	if (IS_ERR(sgls))
 		return PTR_ERR(sgls);
 	ret = uverbs_request_finish(&iter);
@@ -2195,11 +2202,11 @@
 	if (wqe_size < sizeof(struct ib_uverbs_recv_wr))
 		return ERR_PTR(-EINVAL);
 
-	wqes = uverbs_request_next_ptr(iter, wqe_size * wr_count);
+	wqes = uverbs_request_next_ptr(iter, size_mul(wqe_size, wr_count));
 	if (IS_ERR(wqes))
 		return ERR_CAST(wqes);
-	sgls = uverbs_request_next_ptr(
-		iter, sge_count * sizeof(struct ib_uverbs_sge));
+	sgls = uverbs_request_next_ptr(iter, size_mul(sge_count,
+						      sizeof(struct ib_uverbs_sge)));
 	if (IS_ERR(sgls))
 		return ERR_CAST(sgls);
 	ret = uverbs_request_finish(iter);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/uverbs_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/uverbs_main.c
@@ -222,8 +222,12 @@
 	spin_lock_irq(&ev_queue->lock);
 
 	while (list_empty(&ev_queue->event_list)) {
-		spin_unlock_irq(&ev_queue->lock);
+		if (ev_queue->is_closed) {
+			spin_unlock_irq(&ev_queue->lock);
+			return -EIO;
+		}
 
+		spin_unlock_irq(&ev_queue->lock);
 		if (filp->f_flags & O_NONBLOCK)
 			return -EAGAIN;
 
@@ -233,12 +237,6 @@
 			return -ERESTARTSYS;
 
 		spin_lock_irq(&ev_queue->lock);
-
-		/* If device was disassociated and no event exists set an error */
-		if (list_empty(&ev_queue->event_list) && ev_queue->is_closed) {
-			spin_unlock_irq(&ev_queue->lock);
-			return -EIO;
-		}
 	}
 
 	event = list_entry(ev_queue->event_list.next, struct ib_uverbs_event, list);
@@ -537,7 +535,7 @@
 	if (hdr->in_words * 4 != count)
 		return -EINVAL;
 
-	if (count < method_elm->req_size + sizeof(hdr)) {
+	if (count < method_elm->req_size + sizeof(*hdr)) {
 		/*
 		 * rdma-core v18 and v19 have a bug where they send DESTROY_CQ
 		 * with a 16 byte write instead of 24. Old kernels didn't
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/uverbs_marshall.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/uverbs_marshall.c
@@ -66,7 +66,7 @@
 	struct rdma_ah_attr *src = ah_attr;
 	struct rdma_ah_attr conv_ah;
 
-	memset(&dst->grh.reserved, 0, sizeof(dst->grh.reserved));
+	memset(&dst->grh, 0, sizeof(dst->grh));
 
 	if ((ah_attr->type == RDMA_AH_ATTR_TYPE_OPA) &&
 	    (rdma_ah_get_dlid(ah_attr) > be16_to_cpu(IB_LID_PERMISSIVE)) &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/uverbs_std_types_counters.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/uverbs_std_types_counters.c
@@ -107,6 +107,8 @@
 		return ret;
 
 	uattr = uverbs_attr_get(attrs, UVERBS_ATTR_READ_COUNTERS_BUFF);
+	if (IS_ERR(uattr))
+		return PTR_ERR(uattr);
 	read_attr.ncounters = uattr->ptr_attr.len / sizeof(u64);
 	read_attr.counters_buff = uverbs_zalloc(
 		attrs, array_size(read_attr.ncounters, sizeof(u64)));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/uverbs_uapi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/uverbs_uapi.c
@@ -447,6 +447,9 @@
 	uapi->num_write_ex = max_write_ex + 1;
 	data = kmalloc_array(uapi->num_write + uapi->num_write_ex,
 			     sizeof(*uapi->write_methods), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
 	for (i = 0; i != uapi->num_write + uapi->num_write_ex; i++)
 		data[i] = &uapi->notsupp_method;
 	uapi->write_methods = data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/core/verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/core/verbs.c
@@ -540,6 +540,8 @@
 	else
 		ret = device->ops.create_ah(ah, &init_attr, NULL);
 	if (ret) {
+		if (ah->sgid_attr)
+			rdma_put_gid_attr(ah->sgid_attr);
 		kfree(ah);
 		return ERR_PTR(ret);
 	}
@@ -1232,6 +1234,9 @@
 	INIT_LIST_HEAD(&qp->rdma_mrs);
 	INIT_LIST_HEAD(&qp->sig_mrs);
 
+	qp->send_cq = attr->send_cq;
+	qp->recv_cq = attr->recv_cq;
+
 	rdma_restrack_new(&qp->res, RDMA_RESTRACK_QP);
 	WARN_ONCE(!udata && !caller, "Missing kernel QP owner");
 	rdma_restrack_set_name(&qp->res, udata ? NULL : caller);
@@ -2150,9 +2155,12 @@
 		return mr;
 
 	mr->device = pd->device;
+	mr->type = IB_MR_TYPE_USER;
 	mr->pd = pd;
 	mr->dm = NULL;
 	atomic_inc(&pd->usecnt);
+	mr->iova =  virt_addr;
+	mr->length = length;
 
 	rdma_restrack_new(&mr->res, RDMA_RESTRACK_MR);
 	rdma_restrack_parent_name(&mr->res, &pd->res);
@@ -2959,15 +2967,18 @@
 bool __rdma_block_iter_next(struct ib_block_iter *biter)
 {
 	unsigned int block_offset;
+	unsigned int sg_delta;
 
 	if (!biter->__sg_nents || !biter->__sg)
 		return false;
 
 	biter->__dma_addr = sg_dma_address(biter->__sg) + biter->__sg_advance;
 	block_offset = biter->__dma_addr & (BIT_ULL(biter->__pg_bit) - 1);
-	biter->__sg_advance += BIT_ULL(biter->__pg_bit) - block_offset;
+	sg_delta = BIT_ULL(biter->__pg_bit) - block_offset;
 
-	if (biter->__sg_advance >= sg_dma_len(biter->__sg)) {
+	if (sg_dma_len(biter->__sg) - biter->__sg_advance > sg_delta) {
+		biter->__sg_advance += sg_delta;
+	} else {
 		biter->__sg_advance = 0;
 		biter->__sg = sg_next(biter->__sg);
 		biter->__sg_nents--;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/ib_verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/ib_verbs.c
@@ -137,7 +137,7 @@
 
 	ib_attr->vendor_id = rdev->en_dev->pdev->vendor;
 	ib_attr->vendor_part_id = rdev->en_dev->pdev->device;
-	ib_attr->hw_ver = rdev->en_dev->pdev->subsystem_device;
+	ib_attr->hw_ver = rdev->en_dev->pdev->revision;
 	ib_attr->max_qp = dev_attr->max_qp;
 	ib_attr->max_qp_wr = dev_attr->max_qp_wqes;
 	ib_attr->device_cap_flags =
@@ -792,7 +792,10 @@
 int bnxt_re_destroy_qp(struct ib_qp *ib_qp, struct ib_udata *udata)
 {
 	struct bnxt_re_qp *qp = container_of(ib_qp, struct bnxt_re_qp, ib_qp);
+	struct bnxt_qplib_qp *qplib_qp = &qp->qplib_qp;
 	struct bnxt_re_dev *rdev = qp->rdev;
+	struct bnxt_qplib_nq *scq_nq = NULL;
+	struct bnxt_qplib_nq *rcq_nq = NULL;
 	unsigned int flags;
 	int rc;
 
@@ -826,6 +829,15 @@
 	ib_umem_release(qp->rumem);
 	ib_umem_release(qp->sumem);
 
+	/* Flush all the entries of notification queue associated with
+	 * given qp.
+	 */
+	scq_nq = qplib_qp->scq->nq;
+	rcq_nq = qplib_qp->rcq->nq;
+	bnxt_re_synchronize_nq(scq_nq);
+	if (scq_nq != rcq_nq)
+		bnxt_re_synchronize_nq(rcq_nq);
+
 	return 0;
 }
 
@@ -1693,7 +1705,7 @@
 	switch (srq_attr_mask) {
 	case IB_SRQ_MAX_WR:
 		/* SRQ resize is not supported */
-		break;
+		return -EINVAL;
 	case IB_SRQ_LIMIT:
 		/* Change the SRQ threshold */
 		if (srq_attr->srq_limit > srq->qplib_srq.max_wqe)
@@ -1708,13 +1720,12 @@
 		/* On success, update the shadow */
 		srq->srq_limit = srq_attr->srq_limit;
 		/* No need to Build and send response back to udata */
-		break;
+		return 0;
 	default:
 		ibdev_err(&rdev->ibdev,
 			  "Unsupported srq_attr_mask 0x%x", srq_attr_mask);
 		return -EINVAL;
 	}
-	return 0;
 }
 
 int bnxt_re_query_srq(struct ib_srq *ib_srq, struct ib_srq_attr *srq_attr)
@@ -1924,18 +1935,20 @@
 		}
 	}
 
-	if (qp_attr_mask & IB_QP_PATH_MTU) {
-		qp->qplib_qp.modify_flags |=
-				CMDQ_MODIFY_QP_MODIFY_MASK_PATH_MTU;
-		qp->qplib_qp.path_mtu = __from_ib_mtu(qp_attr->path_mtu);
-		qp->qplib_qp.mtu = ib_mtu_enum_to_int(qp_attr->path_mtu);
-	} else if (qp_attr->qp_state == IB_QPS_RTR) {
-		qp->qplib_qp.modify_flags |=
-			CMDQ_MODIFY_QP_MODIFY_MASK_PATH_MTU;
-		qp->qplib_qp.path_mtu =
-			__from_ib_mtu(iboe_get_mtu(rdev->netdev->mtu));
-		qp->qplib_qp.mtu =
-			ib_mtu_enum_to_int(iboe_get_mtu(rdev->netdev->mtu));
+	if (qp_attr->qp_state == IB_QPS_RTR) {
+		enum ib_mtu qpmtu;
+
+		qpmtu = iboe_get_mtu(rdev->netdev->mtu);
+		if (qp_attr_mask & IB_QP_PATH_MTU) {
+			if (ib_mtu_enum_to_int(qp_attr->path_mtu) >
+			    ib_mtu_enum_to_int(qpmtu))
+				return -EINVAL;
+			qpmtu = qp_attr->path_mtu;
+		}
+
+		qp->qplib_qp.modify_flags |= CMDQ_MODIFY_QP_MODIFY_MASK_PATH_MTU;
+		qp->qplib_qp.path_mtu = __from_ib_mtu(qpmtu);
+		qp->qplib_qp.mtu = ib_mtu_enum_to_int(qpmtu);
 	}
 
 	if (qp_attr_mask & IB_QP_TIMEOUT) {
@@ -2343,7 +2356,7 @@
 		break;
 	case IB_WR_SEND_WITH_IMM:
 		wqe->type = BNXT_QPLIB_SWQE_TYPE_SEND_WITH_IMM;
-		wqe->send.imm_data = wr->ex.imm_data;
+		wqe->send.imm_data = be32_to_cpu(wr->ex.imm_data);
 		break;
 	case IB_WR_SEND_WITH_INV:
 		wqe->type = BNXT_QPLIB_SWQE_TYPE_SEND_WITH_INV;
@@ -2373,7 +2386,7 @@
 		break;
 	case IB_WR_RDMA_WRITE_WITH_IMM:
 		wqe->type = BNXT_QPLIB_SWQE_TYPE_RDMA_WRITE_WITH_IMM;
-		wqe->rdma.imm_data = wr->ex.imm_data;
+		wqe->rdma.imm_data = be32_to_cpu(wr->ex.imm_data);
 		break;
 	case IB_WR_RDMA_READ:
 		wqe->type = BNXT_QPLIB_SWQE_TYPE_RDMA_READ;
@@ -3235,9 +3248,7 @@
 	udwr.remote_qkey = gsi_sqp->qplib_qp.qkey;
 
 	/* post data received  in the send queue */
-	rc = bnxt_re_post_send_shadow_qp(rdev, gsi_sqp, swr);
-
-	return 0;
+	return bnxt_re_post_send_shadow_qp(rdev, gsi_sqp, swr);
 }
 
 static void bnxt_re_process_res_rawqp1_wc(struct ib_wc *wc,
@@ -3325,7 +3336,7 @@
 	wc->byte_len = orig_cqe->length;
 	wc->qp = &gsi_qp->ib_qp;
 
-	wc->ex.imm_data = orig_cqe->immdata;
+	wc->ex.imm_data = cpu_to_be32(orig_cqe->immdata);
 	wc->src_qp = orig_cqe->src_qp;
 	memcpy(wc->smac, orig_cqe->smac, ETH_ALEN);
 	if (bnxt_re_is_vlan_pkt(orig_cqe, &vlan_id, &sl)) {
@@ -3354,8 +3365,11 @@
 				      struct ib_wc *wc,
 				      struct bnxt_qplib_cqe *cqe)
 {
+	struct bnxt_re_dev *rdev;
+	u16 vlan_id = 0;
 	u8 nw_type;
 
+	rdev = qp->rdev;
 	wc->opcode = IB_WC_RECV;
 	wc->status = __rc_to_ib_wc_status(cqe->status);
 
@@ -3367,9 +3381,12 @@
 		memcpy(wc->smac, cqe->smac, ETH_ALEN);
 		wc->wc_flags |= IB_WC_WITH_SMAC;
 		if (cqe->flags & CQ_RES_UD_FLAGS_META_FORMAT_VLAN) {
-			wc->vlan_id = (cqe->cfa_meta & 0xFFF);
-			if (wc->vlan_id < 0x1000)
-				wc->wc_flags |= IB_WC_WITH_VLAN;
+			vlan_id = (cqe->cfa_meta & 0xFFF);
+		}
+		/* Mark only if vlan_id is non zero */
+		if (vlan_id && bnxt_re_check_if_vlan_valid(rdev, vlan_id)) {
+			wc->vlan_id = vlan_id;
+			wc->wc_flags |= IB_WC_WITH_VLAN;
 		}
 		nw_type = (cqe->flags & CQ_RES_UD_FLAGS_ROCE_IP_VER_MASK) >>
 			   CQ_RES_UD_FLAGS_ROCE_IP_VER_SFT;
@@ -3455,7 +3472,10 @@
 				 (unsigned long)(cqe->qp_handle),
 				 struct bnxt_re_qp, qplib_qp);
 			wc->qp = &qp->ib_qp;
-			wc->ex.imm_data = cqe->immdata;
+			if (cqe->flags & CQ_RES_RC_FLAGS_IMM)
+				wc->ex.imm_data = cpu_to_be32(cqe->immdata);
+			else
+				wc->ex.invalidate_rkey = cqe->invrkey;
 			wc->src_qp = cqe->src_qp;
 			memcpy(wc->smac, cqe->smac, ETH_ALEN);
 			wc->port_num = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/main.c
@@ -70,7 +70,7 @@
 		BNXT_RE_DESC "\n";
 
 MODULE_AUTHOR("Eddie Wai <eddie.wai@broadcom.com>");
-MODULE_DESCRIPTION(BNXT_RE_DESC " Driver");
+MODULE_DESCRIPTION(BNXT_RE_DESC);
 MODULE_LICENSE("Dual BSD/GPL");
 
 /* globals */
@@ -331,15 +331,21 @@
 	for (indx = 0; indx < rdev->num_msix; indx++)
 		rdev->msix_entries[indx].vector = ent[indx].vector;
 
-	bnxt_qplib_rcfw_start_irq(rcfw, msix_ent[BNXT_RE_AEQ_IDX].vector,
-				  false);
+	rc = bnxt_qplib_rcfw_start_irq(rcfw, msix_ent[BNXT_RE_AEQ_IDX].vector,
+				       false);
+	if (rc) {
+		ibdev_warn(&rdev->ibdev, "Failed to reinit CREQ\n");
+		return;
+	}
 	for (indx = BNXT_RE_NQ_IDX ; indx < rdev->num_msix; indx++) {
 		nq = &rdev->nq[indx - 1];
 		rc = bnxt_qplib_nq_start_irq(nq, indx - 1,
 					     msix_ent[indx].vector, false);
-		if (rc)
+		if (rc) {
 			ibdev_warn(&rdev->ibdev, "Failed to reinit NQ index %d\n",
 				   indx - 1);
+			return;
+		}
 	}
 }
 
@@ -1173,12 +1179,6 @@
 	if (!ib_device_try_get(&rdev->ibdev))
 		return 0;
 
-	if (!sgid_tbl) {
-		ibdev_err(&rdev->ibdev, "QPLIB: SGID table not allocated");
-		rc = -EINVAL;
-		goto out;
-	}
-
 	for (index = 0; index < sgid_tbl->active; index++) {
 		gid_idx = sgid_tbl->hw_id[index];
 
@@ -1196,7 +1196,7 @@
 		rc = bnxt_qplib_update_sgid(sgid_tbl, &gid, gid_idx,
 					    rdev->qplib_res.netdev->dev_addr);
 	}
-out:
+
 	ib_device_put(&rdev->ibdev);
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/qplib_fp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/qplib_fp.c
@@ -386,6 +386,24 @@
 	spin_unlock_bh(&hwq->lock);
 }
 
+/* bnxt_re_synchronize_nq - self polling notification queue.
+ * @nq      -     notification queue pointer
+ *
+ * This function will start polling entries of a given notification queue
+ * for all pending  entries.
+ * This function is useful to synchronize notification entries while resources
+ * are going away.
+ */
+
+void bnxt_re_synchronize_nq(struct bnxt_qplib_nq *nq)
+{
+	int budget = nq->budget;
+
+	nq->budget = nq->hwq.max_elements;
+	bnxt_qplib_service_nq(&nq->nq_tasklet);
+	nq->budget = budget;
+}
+
 static irqreturn_t bnxt_qplib_nq_irq(int irq, void *dev_instance)
 {
 	struct bnxt_qplib_nq *nq = dev_instance;
@@ -404,6 +422,9 @@
 
 void bnxt_qplib_nq_stop_irq(struct bnxt_qplib_nq *nq, bool kill)
 {
+	if (!nq->requested)
+		return;
+
 	tasklet_disable(&nq->nq_tasklet);
 	/* Mask h/w interrupt */
 	bnxt_qplib_ring_nq_db(&nq->nq_db.dbinfo, nq->res->cctx, false);
@@ -411,11 +432,12 @@
 	synchronize_irq(nq->msix_vec);
 	if (kill)
 		tasklet_kill(&nq->nq_tasklet);
-	if (nq->requested) {
-		irq_set_affinity_hint(nq->msix_vec, NULL);
-		free_irq(nq->msix_vec, nq);
-		nq->requested = false;
-	}
+
+	irq_set_affinity_hint(nq->msix_vec, NULL);
+	free_irq(nq->msix_vec, nq);
+	kfree(nq->name);
+	nq->name = NULL;
+	nq->requested = false;
 }
 
 void bnxt_qplib_disable_nq(struct bnxt_qplib_nq *nq)
@@ -441,6 +463,7 @@
 int bnxt_qplib_nq_start_irq(struct bnxt_qplib_nq *nq, int nq_indx,
 			    int msix_vector, bool need_init)
 {
+	struct bnxt_qplib_res *res = nq->res;
 	int rc;
 
 	if (nq->requested)
@@ -452,10 +475,17 @@
 	else
 		tasklet_enable(&nq->nq_tasklet);
 
-	snprintf(nq->name, sizeof(nq->name), "bnxt_qplib_nq-%d", nq_indx);
+	nq->name = kasprintf(GFP_KERNEL, "bnxt_re-nq-%d@pci:%s",
+			     nq_indx, pci_name(res->pdev));
+	if (!nq->name)
+		return -ENOMEM;
 	rc = request_irq(nq->msix_vec, bnxt_qplib_nq_irq, 0, nq->name, nq);
-	if (rc)
+	if (rc) {
+		kfree(nq->name);
+		nq->name = NULL;
+		tasklet_disable(&nq->nq_tasklet);
 		return rc;
+	}
 
 	cpumask_clear(&nq->mask);
 	cpumask_set_cpu(nq_indx, &nq->mask);
@@ -466,7 +496,7 @@
 			 nq->msix_vec, nq_indx);
 	}
 	nq->requested = true;
-	bnxt_qplib_ring_nq_db(&nq->nq_db.dbinfo, nq->res->cctx, true);
+	bnxt_qplib_ring_nq_db(&nq->nq_db.dbinfo, res->cctx, true);
 
 	return rc;
 }
@@ -707,12 +737,13 @@
 	int rc = 0;
 
 	RCFW_CMD_PREP(req, QUERY_SRQ, cmd_flags);
-	req.srq_cid = cpu_to_le32(srq->id);
 
 	/* Configure the request */
 	sbuf = bnxt_qplib_rcfw_alloc_sbuf(rcfw, sizeof(*sb));
 	if (!sbuf)
 		return -ENOMEM;
+	req.resp_size = sizeof(*sb) / BNXT_QPLIB_CMDQE_UNITS;
+	req.srq_cid = cpu_to_le32(srq->id);
 	sb = sbuf->sb;
 	rc = bnxt_qplib_rcfw_send_message(rcfw, (void *)&req, (void *)&resp,
 					  (void *)sbuf, 0);
@@ -1113,9 +1144,11 @@
 		rq->dbinfo.db = qp->dpi->dbr;
 		rq->dbinfo.max_slot = bnxt_qplib_set_rq_max_slot(rq->wqe_size);
 	}
+	spin_lock_bh(&rcfw->tbl_lock);
 	tbl_indx = map_qp_id_to_tbl_indx(qp->id, rcfw);
 	rcfw->qp_tbl[tbl_indx].qp_id = qp->id;
 	rcfw->qp_tbl[tbl_indx].qp_handle = (void *)qp;
+	spin_unlock_bh(&rcfw->tbl_lock);
 
 	return 0;
 fail:
@@ -1148,8 +1181,6 @@
 			qp->path_mtu =
 				CMDQ_MODIFY_QP_PATH_MTU_MTU_2048;
 		}
-		qp->modify_flags &=
-			~CMDQ_MODIFY_QP_MODIFY_MASK_VLAN_ID;
 		/* Bono FW require the max_dest_rd_atomic to be >= 1 */
 		if (qp->max_dest_rd_atomic < 1)
 			qp->max_dest_rd_atomic = 1;
@@ -1463,9 +1494,11 @@
 	u32 tbl_indx;
 	int rc;
 
+	spin_lock_bh(&rcfw->tbl_lock);
 	tbl_indx = map_qp_id_to_tbl_indx(qp->id, rcfw);
 	rcfw->qp_tbl[tbl_indx].qp_id = BNXT_QPLIB_QP_ID_INVALID;
 	rcfw->qp_tbl[tbl_indx].qp_handle = NULL;
+	spin_unlock_bh(&rcfw->tbl_lock);
 
 	RCFW_CMD_PREP(req, DESTROY_QP, cmd_flags);
 
@@ -1473,8 +1506,10 @@
 	rc = bnxt_qplib_rcfw_send_message(rcfw, (void *)&req,
 					  (void *)&resp, NULL, 0);
 	if (rc) {
+		spin_lock_bh(&rcfw->tbl_lock);
 		rcfw->qp_tbl[tbl_indx].qp_id = qp->id;
 		rcfw->qp_tbl[tbl_indx].qp_handle = qp;
+		spin_unlock_bh(&rcfw->tbl_lock);
 		return rc;
 	}
 
@@ -1598,7 +1633,7 @@
 		il_src = (void *)wqe->sg_list[indx].addr;
 		t_len += len;
 		if (t_len > qp->max_inline_data)
-			goto bad;
+			return -ENOMEM;
 		while (len) {
 			if (pull_dst) {
 				pull_dst = false;
@@ -1622,8 +1657,6 @@
 	}
 
 	return t_len;
-bad:
-	return -ENOMEM;
 }
 
 static u32 bnxt_qplib_put_sges(struct bnxt_qplib_hwq *hwq,
@@ -2040,6 +2073,12 @@
 	u32 pg_sz_lvl;
 	int rc;
 
+	if (!cq->dpi) {
+		dev_err(&rcfw->pdev->dev,
+			"FP: CREATE_CQ failed due to NULL DPI\n");
+		return -EINVAL;
+	}
+
 	hwq_attr.res = res;
 	hwq_attr.depth = cq->max_wqe;
 	hwq_attr.stride = sizeof(struct cq_base);
@@ -2047,15 +2086,10 @@
 	hwq_attr.sginfo = &cq->sg_info;
 	rc = bnxt_qplib_alloc_init_hwq(&cq->hwq, &hwq_attr);
 	if (rc)
-		goto exit;
+		return rc;
 
 	RCFW_CMD_PREP(req, CREATE_CQ, cmd_flags);
 
-	if (!cq->dpi) {
-		dev_err(&rcfw->pdev->dev,
-			"FP: CREATE_CQ failed due to NULL DPI\n");
-		return -EINVAL;
-	}
 	req.dpi = cpu_to_le32(cq->dpi->dpi);
 	req.cq_handle = cpu_to_le64(cq->cq_handle);
 	req.cq_size = cpu_to_le32(cq->hwq.max_elements);
@@ -2093,7 +2127,6 @@
 
 fail:
 	bnxt_qplib_free_hwq(res, &cq->hwq);
-exit:
 	return rc;
 }
 
@@ -2721,11 +2754,8 @@
 
 	qp = (struct bnxt_qplib_qp *)((unsigned long)
 				      le64_to_cpu(hwcqe->qp_handle));
-	if (!qp) {
-		dev_err(&cq->hwq.pdev->dev,
-			"FP: CQ Process terminal qp is NULL\n");
+	if (!qp)
 		return -EINVAL;
-	}
 
 	/* Must block new posting of SQ and RQ */
 	qp->state = CMDQ_MODIFY_QP_NEW_STATE_ERR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/qplib_fp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/qplib_fp.h
@@ -164,12 +164,12 @@
 		/* Send, with imm, inval key */
 		struct {
 			union {
-				__be32	imm_data;
+				u32	imm_data;
 				u32	inv_key;
 			};
 			u32		q_key;
 			u32		dst_qp;
-			u16		avid;
+			u32		avid;
 		} send;
 
 		/* Send Raw Ethernet and QP1 */
@@ -182,7 +182,7 @@
 		/* RDMA write, with imm, read */
 		struct {
 			union {
-				__be32	imm_data;
+				u32	imm_data;
 				u32	inv_key;
 			};
 			u64		remote_va;
@@ -374,7 +374,7 @@
 	u16				cfa_meta;
 	u64				wr_id;
 	union {
-		__be32			immdata;
+		u32			immdata;
 		u32			invrkey;
 	};
 	u64				qp_handle;
@@ -471,7 +471,7 @@
 struct bnxt_qplib_nq {
 	struct pci_dev			*pdev;
 	struct bnxt_qplib_res		*res;
-	char				name[32];
+	char				*name;
 	struct bnxt_qplib_hwq		hwq;
 	struct bnxt_qplib_nq_db		nq_db;
 	u16				ring_id;
@@ -548,6 +548,7 @@
 				  struct bnxt_qplib_cqe *cqe,
 				  int num_cqes);
 void bnxt_qplib_flush_cqn_wq(struct bnxt_qplib_qp *qp);
+void bnxt_re_synchronize_nq(struct bnxt_qplib_nq *nq);
 
 static inline void *bnxt_qplib_get_swqe(struct bnxt_qplib_q *que, u32 *swq_idx)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/qplib_rcfw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/qplib_rcfw.c
@@ -181,7 +181,7 @@
 	} while (size > 0);
 	cmdq->seq_num++;
 
-	cmdq_prod = hwq->prod;
+	cmdq_prod = hwq->prod & 0xFFFF;
 	if (test_bit(FIRMWARE_FIRST_FLAG, &cmdq->flags)) {
 		/* The very first doorbell write
 		 * is required to set this flag
@@ -249,7 +249,7 @@
 		/* failed with status */
 		dev_err(&rcfw->pdev->dev, "cmdq[%#x]=%#x status %#x\n",
 			cookie, opcode, evnt->status);
-		rc = -EFAULT;
+		rc = -EIO;
 	}
 
 	return rc;
@@ -299,7 +299,8 @@
 }
 
 static int bnxt_qplib_process_qp_event(struct bnxt_qplib_rcfw *rcfw,
-				       struct creq_qp_event *qp_event)
+				       struct creq_qp_event *qp_event,
+				       u32 *num_wait)
 {
 	struct creq_qp_error_notification *err_event;
 	struct bnxt_qplib_hwq *hwq = &rcfw->cmdq.hwq;
@@ -308,6 +309,7 @@
 	u16 cbit, blocked = 0;
 	struct pci_dev *pdev;
 	unsigned long flags;
+	u32 wait_cmds = 0;
 	__le16  mcookie;
 	u16 cookie;
 	int rc = 0;
@@ -318,17 +320,21 @@
 	case CREQ_QP_EVENT_EVENT_QP_ERROR_NOTIFICATION:
 		err_event = (struct creq_qp_error_notification *)qp_event;
 		qp_id = le32_to_cpu(err_event->xid);
+		spin_lock(&rcfw->tbl_lock);
 		tbl_indx = map_qp_id_to_tbl_indx(qp_id, rcfw);
 		qp = rcfw->qp_tbl[tbl_indx].qp_handle;
+		if (!qp) {
+			spin_unlock(&rcfw->tbl_lock);
+			break;
+		}
+		bnxt_qplib_mark_qp_error(qp);
+		rc = rcfw->creq.aeq_handler(rcfw, qp_event, qp);
+		spin_unlock(&rcfw->tbl_lock);
 		dev_dbg(&pdev->dev, "Received QP error notification\n");
 		dev_dbg(&pdev->dev,
 			"qpid 0x%x, req_err=0x%x, resp_err=0x%x\n",
 			qp_id, err_event->req_err_state_reason,
 			err_event->res_err_state_reason);
-		if (!qp)
-			break;
-		bnxt_qplib_mark_qp_error(qp);
-		rc = rcfw->creq.aeq_handler(rcfw, qp_event, qp);
 		break;
 	default:
 		/*
@@ -367,9 +373,10 @@
 		crsqe->req_size = 0;
 
 		if (!blocked)
-			wake_up(&rcfw->cmdq.waitq);
+			wait_cmds++;
 		spin_unlock_irqrestore(&hwq->lock, flags);
 	}
+	*num_wait += wait_cmds;
 	return rc;
 }
 
@@ -383,6 +390,7 @@
 	struct creq_base *creqe;
 	u32 sw_cons, raw_cons;
 	unsigned long flags;
+	u32 num_wakeup = 0;
 
 	/* Service the CREQ until budget is over */
 	spin_lock_irqsave(&hwq->lock, flags);
@@ -401,7 +409,8 @@
 		switch (type) {
 		case CREQ_BASE_TYPE_QP_EVENT:
 			bnxt_qplib_process_qp_event
-				(rcfw, (struct creq_qp_event *)creqe);
+				(rcfw, (struct creq_qp_event *)creqe,
+				 &num_wakeup);
 			creq->stats.creq_qp_event_processed++;
 			break;
 		case CREQ_BASE_TYPE_FUNC_EVENT:
@@ -429,6 +438,8 @@
 				      rcfw->res->cctx, true);
 	}
 	spin_unlock_irqrestore(&hwq->lock, flags);
+	if (num_wakeup)
+		wake_up_nr(&rcfw->cmdq.waitq, num_wakeup);
 }
 
 static irqreturn_t bnxt_qplib_creq_irq(int irq, void *dev_instance)
@@ -599,7 +610,7 @@
 		rcfw->cmdq_depth = BNXT_QPLIB_CMDQE_MAX_CNT_8192;
 
 	sginfo.pgsize = bnxt_qplib_cmdqe_page_size(rcfw->cmdq_depth);
-	hwq_attr.depth = rcfw->cmdq_depth;
+	hwq_attr.depth = rcfw->cmdq_depth & 0x7FFFFFFF;
 	hwq_attr.stride = BNXT_QPLIB_CMDQE_UNITS;
 	hwq_attr.type = HWQ_TYPE_CTX;
 	if (bnxt_qplib_alloc_init_hwq(&cmdq->hwq, &hwq_attr)) {
@@ -618,14 +629,13 @@
 	if (!cmdq->cmdq_bitmap)
 		goto fail;
 
-	cmdq->bmap_size = bmap_size;
-
 	/* Allocate one extra to hold the QP1 entries */
 	rcfw->qp_tbl_size = qp_tbl_sz + 1;
 	rcfw->qp_tbl = kcalloc(rcfw->qp_tbl_size, sizeof(struct bnxt_qplib_qp_node),
 			       GFP_KERNEL);
 	if (!rcfw->qp_tbl)
 		goto fail;
+	spin_lock_init(&rcfw->tbl_lock);
 
 	return 0;
 
@@ -639,6 +649,10 @@
 	struct bnxt_qplib_creq_ctx *creq;
 
 	creq = &rcfw->creq;
+
+	if (!creq->requested)
+		return;
+
 	tasklet_disable(&creq->creq_tasklet);
 	/* Mask h/w interrupts */
 	bnxt_qplib_ring_nq_db(&creq->creq_db.dbinfo, rcfw->res->cctx, false);
@@ -647,10 +661,10 @@
 	if (kill)
 		tasklet_kill(&creq->creq_tasklet);
 
-	if (creq->requested) {
-		free_irq(creq->msix_vec, rcfw);
-		creq->requested = false;
-	}
+	free_irq(creq->msix_vec, rcfw);
+	kfree(creq->irq_name);
+	creq->irq_name = NULL;
+	creq->requested = false;
 }
 
 void bnxt_qplib_disable_rcfw_channel(struct bnxt_qplib_rcfw *rcfw)
@@ -667,8 +681,8 @@
 	iounmap(cmdq->cmdq_mbox.reg.bar_reg);
 	iounmap(creq->creq_db.reg.bar_reg);
 
-	indx = find_first_bit(cmdq->cmdq_bitmap, cmdq->bmap_size);
-	if (indx != cmdq->bmap_size)
+	indx = find_first_bit(cmdq->cmdq_bitmap, rcfw->cmdq_depth);
+	if (indx != rcfw->cmdq_depth)
 		dev_err(&rcfw->pdev->dev,
 			"disabling RCFW with pending cmd-bit %lx\n", indx);
 
@@ -682,9 +696,11 @@
 			      bool need_init)
 {
 	struct bnxt_qplib_creq_ctx *creq;
+	struct bnxt_qplib_res *res;
 	int rc;
 
 	creq = &rcfw->creq;
+	res = rcfw->res;
 
 	if (creq->requested)
 		return -EFAULT;
@@ -694,13 +710,22 @@
 		tasklet_setup(&creq->creq_tasklet, bnxt_qplib_service_creq);
 	else
 		tasklet_enable(&creq->creq_tasklet);
+
+	creq->irq_name = kasprintf(GFP_KERNEL, "bnxt_re-creq@pci:%s",
+				   pci_name(res->pdev));
+	if (!creq->irq_name)
+		return -ENOMEM;
 	rc = request_irq(creq->msix_vec, bnxt_qplib_creq_irq, 0,
-			 "bnxt_qplib_creq", rcfw);
-	if (rc)
+			 creq->irq_name, rcfw);
+	if (rc) {
+		kfree(creq->irq_name);
+		creq->irq_name = NULL;
+		tasklet_disable(&creq->creq_tasklet);
 		return rc;
+	}
 	creq->requested = true;
 
-	bnxt_qplib_ring_nq_db(&creq->creq_db.dbinfo, rcfw->res->cctx, true);
+	bnxt_qplib_ring_nq_db(&creq->creq_db.dbinfo, res->cctx, true);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/qplib_rcfw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/qplib_rcfw.h
@@ -152,7 +152,6 @@
 	wait_queue_head_t		waitq;
 	unsigned long			flags;
 	unsigned long			*cmdq_bitmap;
-	u32				bmap_size;
 	u32				seq_num;
 };
 
@@ -175,6 +174,7 @@
 	u16				ring_id;
 	int				msix_vec;
 	bool				requested; /*irq handler installed */
+	char				*irq_name;
 };
 
 /* RCFW Communication Channels */
@@ -186,6 +186,8 @@
 	struct bnxt_qplib_crsqe		*crsqe_tbl;
 	int qp_tbl_size;
 	struct bnxt_qplib_qp_node *qp_tbl;
+	/* To synchronize the qp-handle hash table */
+	spinlock_t			tbl_lock;
 	u64 oos_prev;
 	u32 init_oos_stats;
 	u32 cmdq_depth;
@@ -218,9 +220,10 @@
 int bnxt_qplib_init_rcfw(struct bnxt_qplib_rcfw *rcfw,
 			 struct bnxt_qplib_ctx *ctx, int is_virtfn);
 void bnxt_qplib_mark_qp_error(void *qp_handle);
+
 static inline u32 map_qp_id_to_tbl_indx(u32 qid, struct bnxt_qplib_rcfw *rcfw)
 {
 	/* Last index of the qp_tbl is for QP1 ie. qp_tbl_size - 1*/
-	return (qid == 1) ? rcfw->qp_tbl_size - 1 : qid % rcfw->qp_tbl_size - 2;
+	return (qid == 1) ? rcfw->qp_tbl_size - 1 : (qid % (rcfw->qp_tbl_size - 2));
 }
 #endif /* __BNXT_QPLIB_RCFW_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/qplib_res.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/qplib_res.c
@@ -215,17 +215,9 @@
 			return -EINVAL;
 		hwq_attr->sginfo->npages = npages;
 	} else {
-		unsigned long sginfo_num_pages = ib_umem_num_dma_blocks(
-			hwq_attr->sginfo->umem, hwq_attr->sginfo->pgsize);
-
+		npages = ib_umem_num_dma_blocks(hwq_attr->sginfo->umem,
+						hwq_attr->sginfo->pgsize);
 		hwq->is_user = true;
-		npages = sginfo_num_pages;
-		npages = (npages * PAGE_SIZE) /
-			  BIT_ULL(hwq_attr->sginfo->pgshft);
-		if ((sginfo_num_pages * PAGE_SIZE) %
-		     BIT_ULL(hwq_attr->sginfo->pgshft))
-			if (!npages)
-				npages++;
 	}
 
 	if (npages == MAX_PBL_LVL_0_PGS) {
@@ -251,6 +243,8 @@
 			sginfo.pgsize = npde * pg_size;
 			sginfo.npages = 1;
 			rc = __alloc_pbl(res, &hwq->pbl[PBL_LVL_0], &sginfo);
+			if (rc)
+				goto fail;
 
 			/* Alloc PBL pages */
 			sginfo.npages = npbl;
@@ -262,22 +256,9 @@
 			dst_virt_ptr =
 				(dma_addr_t **)hwq->pbl[PBL_LVL_0].pg_arr;
 			src_phys_ptr = hwq->pbl[PBL_LVL_1].pg_map_arr;
-			if (hwq_attr->type == HWQ_TYPE_MR) {
-			/* For MR it is expected that we supply only 1 contigous
-			 * page i.e only 1 entry in the PDL that will contain
-			 * all the PBLs for the user supplied memory region
-			 */
-				for (i = 0; i < hwq->pbl[PBL_LVL_1].pg_count;
-				     i++)
-					dst_virt_ptr[0][i] = src_phys_ptr[i] |
-						flag;
-			} else {
-				for (i = 0; i < hwq->pbl[PBL_LVL_1].pg_count;
-				     i++)
-					dst_virt_ptr[PTR_PG(i)][PTR_IDX(i)] =
-						src_phys_ptr[i] |
-						PTU_PDE_VALID;
-			}
+			for (i = 0; i < hwq->pbl[PBL_LVL_1].pg_count; i++)
+				dst_virt_ptr[0][i] = src_phys_ptr[i] | flag;
+
 			/* Alloc or init PTEs */
 			rc = __alloc_pbl(res, &hwq->pbl[PBL_LVL_2],
 					 hwq_attr->sginfo);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/bnxt_re/qplib_sp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/bnxt_re/qplib_sp.c
@@ -124,7 +124,7 @@
 	attr->max_qp_init_rd_atom =
 		sb->max_qp_init_rd_atom > BNXT_QPLIB_MAX_OUT_RD_ATOM ?
 		BNXT_QPLIB_MAX_OUT_RD_ATOM : sb->max_qp_init_rd_atom;
-	attr->max_qp_wqes = le16_to_cpu(sb->max_qp_wr);
+	attr->max_qp_wqes = le16_to_cpu(sb->max_qp_wr) - 1;
 	/*
 	 * 128 WQEs needs to be reserved for the HW (8916). Prevent
 	 * reporting the max number
@@ -680,16 +680,15 @@
 		/* Free the hwq if it already exist, must be a rereg */
 		if (mr->hwq.max_elements)
 			bnxt_qplib_free_hwq(res, &mr->hwq);
-		/* Use system PAGE_SIZE */
 		hwq_attr.res = res;
 		hwq_attr.depth = pages;
-		hwq_attr.stride = buf_pg_size;
+		hwq_attr.stride = sizeof(dma_addr_t);
 		hwq_attr.type = HWQ_TYPE_MR;
 		hwq_attr.sginfo = &sginfo;
 		hwq_attr.sginfo->umem = umem;
 		hwq_attr.sginfo->npages = pages;
-		hwq_attr.sginfo->pgsize = PAGE_SIZE;
-		hwq_attr.sginfo->pgshft = PAGE_SHIFT;
+		hwq_attr.sginfo->pgsize = buf_pg_size;
+		hwq_attr.sginfo->pgshft = ilog2(buf_pg_size);
 		rc = bnxt_qplib_alloc_init_hwq(&mr->hwq, &hwq_attr);
 		if (rc) {
 			dev_err(&res->pdev->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/cxgb4/cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/cxgb4/cm.c
@@ -1222,6 +1222,8 @@
 	int ret;
 
 	ep = lookup_atid(t, atid);
+	if (!ep)
+		return -EINVAL;
 
 	pr_debug("ep %p tid %u snd_isn %u rcv_isn %u\n", ep, tid,
 		 be32_to_cpu(req->snd_isn), be32_to_cpu(req->rcv_isn));
@@ -1965,6 +1967,9 @@
 	int win;
 
 	skb = get_skb(NULL, sizeof(*req), GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
+
 	req = __skb_put_zero(skb, sizeof(*req));
 	req->op_compl = htonl(WR_OP_V(FW_OFLD_CONNECTION_WR));
 	req->len16_pkd = htonl(FW_WR_LEN16_V(DIV_ROUND_UP(sizeof(*req), 16)));
@@ -2081,7 +2086,7 @@
 	err = -ENOMEM;
 	if (n->dev->flags & IFF_LOOPBACK) {
 		if (iptype == 4)
-			pdev = ip_dev_find(&init_net, *(__be32 *)peer_ip);
+			pdev = __ip_dev_find(&init_net, *(__be32 *)peer_ip, false);
 		else if (IS_ENABLED(CONFIG_IPV6))
 			for_each_netdev(&init_net, pdev) {
 				if (ipv6_chk_addr(&init_net,
@@ -2096,12 +2101,12 @@
 			err = -ENODEV;
 			goto out;
 		}
+		if (is_vlan_dev(pdev))
+			pdev = vlan_dev_real_dev(pdev);
 		ep->l2t = cxgb4_l2t_get(cdev->rdev.lldi.l2t,
 					n, pdev, rt_tos2priority(tos));
-		if (!ep->l2t) {
-			dev_put(pdev);
+		if (!ep->l2t)
 			goto out;
-		}
 		ep->mtu = pdev->mtu;
 		ep->tx_chan = cxgb4_port_chan(pdev);
 		ep->smac_idx = ((struct port_info *)netdev_priv(pdev))->smt_idx;
@@ -2114,7 +2119,6 @@
 		ep->rss_qid = cdev->rdev.lldi.rxq_ids[
 			cxgb4_port_idx(pdev) * step];
 		set_tcp_window(ep, (struct port_info *)netdev_priv(pdev));
-		dev_put(pdev);
 	} else {
 		pdev = get_real_dev(n->dev);
 		ep->l2t = cxgb4_l2t_get(cdev->rdev.lldi.l2t,
@@ -2276,6 +2280,9 @@
 	int ret = 0;
 
 	ep = lookup_atid(t, atid);
+	if (!ep)
+		return -EINVAL;
+
 	la = (struct sockaddr_in *)&ep->com.local_addr;
 	ra = (struct sockaddr_in *)&ep->com.remote_addr;
 	la6 = (struct sockaddr_in6 *)&ep->com.local_addr;
@@ -2682,6 +2689,9 @@
 	u16 tcp_opt = ntohs(req->tcp_opt);
 
 	ep = get_ep_from_tid(dev, tid);
+	if (!ep)
+		return 0;
+
 	pr_debug("ep %p tid %u\n", ep, ep->hwtid);
 	ep->snd_seq = be32_to_cpu(req->snd_isn);
 	ep->rcv_seq = be32_to_cpu(req->rcv_isn);
@@ -4150,6 +4160,10 @@
 
 	if (neigh->dev->flags & IFF_LOOPBACK) {
 		pdev = ip_dev_find(&init_net, iph->daddr);
+		if (!pdev) {
+			pr_err("%s - failed to find device!\n", __func__);
+			goto free_dst;
+		}
 		e = cxgb4_l2t_get(dev->rdev.lldi.l2t, neigh,
 				    pdev, 0);
 		pi = (struct port_info *)netdev_priv(pdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/cxgb4/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/cxgb4/device.c
@@ -1114,8 +1114,10 @@
 	 * The math here assumes sizeof cpl_pass_accept_req >= sizeof
 	 * cpl_rx_pkt.
 	 */
-	skb = alloc_skb(gl->tot_len + sizeof(struct cpl_pass_accept_req) +
-			sizeof(struct rss_header) - pktshift, GFP_ATOMIC);
+	skb = alloc_skb(size_add(gl->tot_len,
+				 sizeof(struct cpl_pass_accept_req) +
+				 sizeof(struct rss_header)) - pktshift,
+			GFP_ATOMIC);
 	if (unlikely(!skb))
 		return NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/cxgb4/provider.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/cxgb4/provider.c
@@ -469,6 +469,7 @@
 	.fill_res_cq_entry = c4iw_fill_res_cq_entry,
 	.fill_res_cm_id_entry = c4iw_fill_res_cm_id_entry,
 	.fill_res_mr_entry = c4iw_fill_res_mr_entry,
+	.fill_res_qp_entry = c4iw_fill_res_qp_entry,
 	.get_dev_fw_str = get_dev_fw_str,
 	.get_dma_mr = c4iw_get_dma_mr,
 	.get_hw_stats = c4iw_get_mib,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/cxgb4/qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/cxgb4/qp.c
@@ -2460,6 +2460,7 @@
 	memset(attr, 0, sizeof(*attr));
 	memset(init_attr, 0, sizeof(*init_attr));
 	attr->qp_state = to_ib_qp_state(qhp->attr.state);
+	attr->cur_qp_state = to_ib_qp_state(qhp->attr.state);
 	init_attr->cap.max_send_wr = qhp->attr.sq_num_entries;
 	init_attr->cap.max_recv_wr = qhp->attr.rq_num_entries;
 	init_attr->cap.max_send_sge = qhp->attr.sq_max_sges;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/cxgb4/restrack.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/cxgb4/restrack.c
@@ -238,7 +238,7 @@
 	if (rdma_nl_put_driver_u64_hex(msg, "history", epcp->history))
 		goto err_cancel_table;
 
-	if (epcp->state == LISTEN) {
+	if (listen_ep) {
 		if (rdma_nl_put_driver_u32(msg, "stid", listen_ep->stid))
 			goto err_cancel_table;
 		if (rdma_nl_put_driver_u32(msg, "backlog", listen_ep->backlog))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/efa/efa_com.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/efa/efa_com.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
 /*
- * Copyright 2018-2021 Amazon.com, Inc. or its affiliates. All rights reserved.
+ * Copyright 2018-2024 Amazon.com, Inc. or its affiliates. All rights reserved.
  */
 
 #include "efa_com.h"
@@ -398,8 +398,8 @@
 	return comp_ctx;
 }
 
-static void efa_com_handle_single_admin_completion(struct efa_com_admin_queue *aq,
-						   struct efa_admin_acq_entry *cqe)
+static int efa_com_handle_single_admin_completion(struct efa_com_admin_queue *aq,
+						  struct efa_admin_acq_entry *cqe)
 {
 	struct efa_comp_ctx *comp_ctx;
 	u16 cmd_id;
@@ -408,11 +408,11 @@
 			 EFA_ADMIN_ACQ_COMMON_DESC_COMMAND_ID);
 
 	comp_ctx = efa_com_get_comp_ctx(aq, cmd_id, false);
-	if (!comp_ctx) {
+	if (comp_ctx->status != EFA_CMD_SUBMITTED) {
 		ibdev_err(aq->efa_dev,
-			  "comp_ctx is NULL. Changing the admin queue running state\n");
-		clear_bit(EFA_AQ_STATE_RUNNING_BIT, &aq->state);
-		return;
+			  "Received completion with unexpected command id[%d], sq producer: %d, sq consumer: %d, cq consumer: %d\n",
+			  cmd_id, aq->sq.pc, aq->sq.cc, aq->cq.cc);
+		return -EINVAL;
 	}
 
 	comp_ctx->status = EFA_CMD_COMPLETED;
@@ -420,14 +420,17 @@
 
 	if (!test_bit(EFA_AQ_STATE_POLLING_BIT, &aq->state))
 		complete(&comp_ctx->wait_event);
+
+	return 0;
 }
 
 static void efa_com_handle_admin_completion(struct efa_com_admin_queue *aq)
 {
 	struct efa_admin_acq_entry *cqe;
 	u16 queue_size_mask;
-	u16 comp_num = 0;
+	u16 comp_cmds = 0;
 	u8 phase;
+	int err;
 	u16 ci;
 
 	queue_size_mask = aq->depth - 1;
@@ -445,10 +448,12 @@
 		 * phase bit was validated
 		 */
 		dma_rmb();
-		efa_com_handle_single_admin_completion(aq, cqe);
+		err = efa_com_handle_single_admin_completion(aq, cqe);
+		if (!err)
+			comp_cmds++;
 
+		aq->cq.cc++;
 		ci++;
-		comp_num++;
 		if (ci == aq->depth) {
 			ci = 0;
 			phase = !phase;
@@ -457,10 +462,9 @@
 		cqe = &aq->cq.entries[ci];
 	}
 
-	aq->cq.cc += comp_num;
 	aq->cq.phase = phase;
-	aq->sq.cc += comp_num;
-	atomic64_add(comp_num, &aq->stats.completed_cmd);
+	aq->sq.cc += comp_cmds;
+	atomic64_add(comp_cmds, &aq->stats.completed_cmd);
 }
 
 static int efa_com_comp_status_to_errno(u8 comp_status)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/efa/efa_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/efa/efa_main.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
 /*
- * Copyright 2018-2021 Amazon.com, Inc. or its affiliates. All rights reserved.
+ * Copyright 2018-2022 Amazon.com, Inc. or its affiliates. All rights reserved.
  */
 
 #include <linux/module.h>
@@ -14,10 +14,12 @@
 
 #define PCI_DEV_ID_EFA0_VF 0xefa0
 #define PCI_DEV_ID_EFA1_VF 0xefa1
+#define PCI_DEV_ID_EFA2_VF 0xefa2
 
 static const struct pci_device_id efa_pci_tbl[] = {
 	{ PCI_VDEVICE(AMAZON, PCI_DEV_ID_EFA0_VF) },
 	{ PCI_VDEVICE(AMAZON, PCI_DEV_ID_EFA1_VF) },
+	{ PCI_VDEVICE(AMAZON, PCI_DEV_ID_EFA2_VF) },
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/efa/efa_verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/efa/efa_verbs.c
@@ -1334,7 +1334,7 @@
  */
 static int pbl_indirect_initialize(struct efa_dev *dev, struct pbl_context *pbl)
 {
-	u32 size_in_pages = DIV_ROUND_UP(pbl->pbl_buf_size_in_bytes, PAGE_SIZE);
+	u32 size_in_pages = DIV_ROUND_UP(pbl->pbl_buf_size_in_bytes, EFA_CHUNK_PAYLOAD_SIZE);
 	struct scatterlist *sgl;
 	int sg_dma_cnt, err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/affinity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/affinity.c
@@ -178,6 +178,8 @@
 	for (node = 0; node < node_affinity.num_possible_nodes; node++)
 		hfi1_per_node_cntr[node] = 1;
 
+	pci_dev_put(dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/chip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/chip.c
@@ -1055,7 +1055,7 @@
 static void handle_temp_err(struct hfi1_devdata *dd);
 static void dc_shutdown(struct hfi1_devdata *dd);
 static void dc_start(struct hfi1_devdata *dd);
-static int qos_rmt_entries(struct hfi1_devdata *dd, unsigned int *mp,
+static int qos_rmt_entries(unsigned int n_krcv_queues, unsigned int *mp,
 			   unsigned int *np);
 static void clear_full_mgmt_pkey(struct hfi1_pportdata *ppd);
 static int wait_link_transfer_active(struct hfi1_devdata *dd, int wait_ms);
@@ -8414,6 +8414,8 @@
  */
 static void __hfi1_rcd_eoi_intr(struct hfi1_ctxtdata *rcd)
 {
+	if (!rcd->rcvhdrq)
+		return;
 	clear_recv_intr(rcd);
 	if (check_packet_present(rcd))
 		force_recv_intr(rcd);
@@ -12304,6 +12306,7 @@
 
 	if (dd->synth_stats_timer.function)
 		del_timer_sync(&dd->synth_stats_timer);
+	cancel_work_sync(&dd->update_cntr_work);
 	ppd = (struct hfi1_pportdata *)(dd + 1);
 	for (i = 0; i < dd->num_pports; i++, ppd++) {
 		kfree(ppd->cntrs);
@@ -13179,15 +13182,16 @@
 {
 	u64 reg;
 	u16 idx = src / BITS_PER_REGISTER;
+	unsigned long flags;
 
-	spin_lock(&dd->irq_src_lock);
+	spin_lock_irqsave(&dd->irq_src_lock, flags);
 	reg = read_csr(dd, CCE_INT_MASK + (8 * idx));
 	if (set)
 		reg |= bits;
 	else
 		reg &= ~bits;
 	write_csr(dd, CCE_INT_MASK + (8 * idx), reg);
-	spin_unlock(&dd->irq_src_lock);
+	spin_unlock_irqrestore(&dd->irq_src_lock, flags);
 }
 
 /**
@@ -13359,7 +13363,6 @@
 	int ret;
 	unsigned ngroups;
 	int rmt_count;
-	int user_rmt_reduced;
 	u32 n_usr_ctxts;
 	u32 send_contexts = chip_send_contexts(dd);
 	u32 rcv_contexts = chip_rcv_contexts(dd);
@@ -13418,28 +13421,34 @@
 					 (num_kernel_contexts + n_usr_ctxts),
 					 &node_affinity.real_cpu_mask);
 	/*
-	 * The RMT entries are currently allocated as shown below:
-	 * 1. QOS (0 to 128 entries);
-	 * 2. FECN (num_kernel_context - 1 + num_user_contexts +
-	 *    num_netdev_contexts);
-	 * 3. netdev (num_netdev_contexts).
-	 * It should be noted that FECN oversubscribe num_netdev_contexts
-	 * entries of RMT because both netdev and PSM could allocate any receive
-	 * context between dd->first_dyn_alloc_text and dd->num_rcv_contexts,
-	 * and PSM FECN must reserve an RMT entry for each possible PSM receive
-	 * context.
-	 */
-	rmt_count = qos_rmt_entries(dd, NULL, NULL) + (num_netdev_contexts * 2);
-	if (HFI1_CAP_IS_KSET(TID_RDMA))
-		rmt_count += num_kernel_contexts - 1;
-	if (rmt_count + n_usr_ctxts > NUM_MAP_ENTRIES) {
-		user_rmt_reduced = NUM_MAP_ENTRIES - rmt_count;
-		dd_dev_err(dd,
-			   "RMT size is reducing the number of user receive contexts from %u to %d\n",
-			   n_usr_ctxts,
-			   user_rmt_reduced);
-		/* recalculate */
-		n_usr_ctxts = user_rmt_reduced;
+	 * RMT entries are allocated as follows:
+	 * 1. QOS (0 to 128 entries)
+	 * 2. FECN (num_kernel_context - 1 [a] + num_user_contexts +
+	 *          num_netdev_contexts [b])
+	 * 3. netdev (NUM_NETDEV_MAP_ENTRIES)
+	 *
+	 * Notes:
+	 * [a] Kernel contexts (except control) are included in FECN if kernel
+	 *     TID_RDMA is active.
+	 * [b] Netdev and user contexts are randomly allocated from the same
+	 *     context pool, so FECN must cover all contexts in the pool.
+	 */
+	rmt_count = qos_rmt_entries(num_kernel_contexts - 1, NULL, NULL)
+		    + (HFI1_CAP_IS_KSET(TID_RDMA) ? num_kernel_contexts - 1
+						  : 0)
+		    + n_usr_ctxts
+		    + num_netdev_contexts
+		    + NUM_NETDEV_MAP_ENTRIES;
+	if (rmt_count > NUM_MAP_ENTRIES) {
+		int over = rmt_count - NUM_MAP_ENTRIES;
+		/* try to squish user contexts, minimum of 1 */
+		if (over >= n_usr_ctxts) {
+			dd_dev_err(dd, "RMT overflow: reduce the requested number of contexts\n");
+			return -EINVAL;
+		}
+		dd_dev_err(dd, "RMT overflow: reducing # user contexts from %u to %u\n",
+			   n_usr_ctxts, n_usr_ctxts - over);
+		n_usr_ctxts -= over;
 	}
 
 	/* the first N are kernel contexts, the rest are user/netdev contexts */
@@ -14296,15 +14305,15 @@
 }
 
 /* return the number of RSM map table entries that will be used for QOS */
-static int qos_rmt_entries(struct hfi1_devdata *dd, unsigned int *mp,
+static int qos_rmt_entries(unsigned int n_krcv_queues, unsigned int *mp,
 			   unsigned int *np)
 {
 	int i;
 	unsigned int m, n;
-	u8 max_by_vl = 0;
+	uint max_by_vl = 0;
 
 	/* is QOS active at all? */
-	if (dd->n_krcv_queues <= MIN_KERNEL_KCTXTS ||
+	if (n_krcv_queues < MIN_KERNEL_KCTXTS ||
 	    num_vls == 1 ||
 	    krcvqsset <= 1)
 		goto no_qos;
@@ -14362,7 +14371,7 @@
 
 	if (!rmt)
 		goto bail;
-	rmt_entries = qos_rmt_entries(dd, &m, &n);
+	rmt_entries = qos_rmt_entries(dd->n_krcv_queues - 1, &m, &n);
 	if (rmt_entries == 0)
 		goto bail;
 	qpns_per_vl = 1 << m;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/driver.c
@@ -1011,6 +1011,8 @@
 	struct hfi1_packet packet;
 	int skip_pkt = 0;
 
+	if (!rcd->rcvhdrq)
+		return RCV_PKT_OK;
 	/* Control context will always use the slow path interrupt handler */
 	needset = (rcd->ctxt == HFI1_CTRL_CTXT) ? 0 : 1;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/efivar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/efivar.c
@@ -110,7 +110,7 @@
 		      unsigned long *size, void **return_data)
 {
 	char prefix_name[64];
-	char name[64];
+	char name[128];
 	int result;
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/file_ops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/file_ops.c
@@ -265,6 +265,8 @@
 	unsigned long dim = from->nr_segs;
 	int idx;
 
+	if (!HFI1_CAP_IS_KSET(SDMA))
+		return -EINVAL;
 	idx = srcu_read_lock(&fd->pq_srcu);
 	pq = srcu_dereference(fd->pq, &fd->pq_srcu);
 	if (!cq || !pq) {
@@ -1177,8 +1179,10 @@
 		goto done;
 
 	ret = init_user_ctxt(fd, uctxt);
-	if (ret)
+	if (ret) {
+		hfi1_free_ctxt_rcv_groups(uctxt);
 		goto done;
+	}
 
 	user_init(uctxt);
 
@@ -1314,12 +1318,15 @@
 		addr = arg + offsetof(struct hfi1_tid_info, tidcnt);
 		if (copy_to_user((void __user *)addr, &tinfo.tidcnt,
 				 sizeof(tinfo.tidcnt)))
-			return -EFAULT;
+			ret = -EFAULT;
 
 		addr = arg + offsetof(struct hfi1_tid_info, length);
-		if (copy_to_user((void __user *)addr, &tinfo.length,
+		if (!ret && copy_to_user((void __user *)addr, &tinfo.length,
 				 sizeof(tinfo.length)))
 			ret = -EFAULT;
+
+		if (ret)
+			hfi1_user_exp_rcv_invalid(fd, &tinfo);
 	}
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/firmware.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/firmware.c
@@ -1744,6 +1744,7 @@
 
 	if (!dd->platform_config.data) {
 		dd_dev_err(dd, "%s: Missing config file\n", __func__);
+		ret = -EINVAL;
 		goto bail;
 	}
 	ptr = (u32 *)dd->platform_config.data;
@@ -1752,6 +1753,7 @@
 	ptr++;
 	if (magic_num != PLATFORM_CONFIG_MAGIC_NUM) {
 		dd_dev_err(dd, "%s: Bad config file\n", __func__);
+		ret = -EINVAL;
 		goto bail;
 	}
 
@@ -1775,6 +1777,7 @@
 	if (file_length > dd->platform_config.size) {
 		dd_dev_info(dd, "%s:File claims to be larger than read size\n",
 			    __func__);
+		ret = -EINVAL;
 		goto bail;
 	} else if (file_length < dd->platform_config.size) {
 		dd_dev_info(dd,
@@ -1795,6 +1798,7 @@
 			dd_dev_err(dd, "%s: Failed validation at offset %ld\n",
 				   __func__, (ptr - (u32 *)
 					      dd->platform_config.data));
+			ret = -EINVAL;
 			goto bail;
 		}
 
@@ -1838,6 +1842,7 @@
 					   __func__, table_type,
 					   (ptr - (u32 *)
 					    dd->platform_config.data));
+				ret = -EINVAL;
 				goto bail; /* We don't trust this file now */
 			}
 			pcfgcache->config_tables[table_type].table = ptr;
@@ -1857,6 +1862,7 @@
 					   __func__, table_type,
 					   (ptr -
 					    (u32 *)dd->platform_config.data));
+				ret = -EINVAL;
 				goto bail; /* We don't trust this file now */
 			}
 			pcfgcache->config_tables[table_type].table_metadata =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/init.c
@@ -112,7 +112,6 @@
 	rcd->fast_handler = get_dma_rtail_setting(rcd) ?
 				handle_receive_interrupt_dma_rtail :
 				handle_receive_interrupt_nodma_rtail;
-	rcd->slow_handler = handle_receive_interrupt;
 
 	hfi1_set_seq_cnt(rcd, 1);
 
@@ -333,6 +332,8 @@
 		rcd->numa_id = numa;
 		rcd->rcv_array_groups = dd->rcv_entries.ngroups;
 		rcd->rhf_rcv_function_map = normal_rhf_rcv_functions;
+		rcd->slow_handler = handle_receive_interrupt;
+		rcd->do_interrupt = rcd->slow_handler;
 		rcd->msix_intr = CCE_NUM_MSIX_VECTORS;
 
 		mutex_init(&rcd->exp_mutex);
@@ -487,7 +488,7 @@
 	u16 shift, mult;
 	u64 src;
 	u32 current_egress_rate; /* Mbits /sec */
-	u32 max_pkt_time;
+	u64 max_pkt_time;
 	/*
 	 * max_pkt_time is the maximum packet egress time in units
 	 * of the fabric clock period 1/(805 MHz).
@@ -873,18 +874,6 @@
 	if (ret)
 		goto done;
 
-	/* allocate dummy tail memory for all receive contexts */
-	dd->rcvhdrtail_dummy_kvaddr = dma_alloc_coherent(&dd->pcidev->dev,
-							 sizeof(u64),
-							 &dd->rcvhdrtail_dummy_dma,
-							 GFP_KERNEL);
-
-	if (!dd->rcvhdrtail_dummy_kvaddr) {
-		dd_dev_err(dd, "cannot allocate dummy tail memory\n");
-		ret = -ENOMEM;
-		goto done;
-	}
-
 	/* dd->rcd can be NULL if early initialization failed */
 	for (i = 0; dd->rcd && i < dd->first_dyn_alloc_ctxt; ++i) {
 		/*
@@ -897,8 +886,6 @@
 		if (!rcd)
 			continue;
 
-		rcd->do_interrupt = &handle_receive_interrupt;
-
 		lastfail = hfi1_create_rcvhdrq(dd, rcd);
 		if (!lastfail)
 			lastfail = hfi1_setup_eagerbufs(rcd);
@@ -1119,7 +1106,7 @@
 	rcd->egrbufs.rcvtids = NULL;
 
 	for (e = 0; e < rcd->egrbufs.alloced; e++) {
-		if (rcd->egrbufs.buffers[e].dma)
+		if (rcd->egrbufs.buffers[e].addr)
 			dma_free_coherent(&dd->pcidev->dev,
 					  rcd->egrbufs.buffers[e].len,
 					  rcd->egrbufs.buffers[e].addr,
@@ -1200,6 +1187,11 @@
 	dd->tx_opstats    = NULL;
 	kfree(dd->comp_vect);
 	dd->comp_vect = NULL;
+	if (dd->rcvhdrtail_dummy_kvaddr)
+		dma_free_coherent(&dd->pcidev->dev, sizeof(u64),
+				  (void *)dd->rcvhdrtail_dummy_kvaddr,
+				  dd->rcvhdrtail_dummy_dma);
+	dd->rcvhdrtail_dummy_kvaddr = NULL;
 	sdma_clean(dd, dd->num_sdma);
 	rvt_dealloc_device(&dd->verbs_dev.rdi);
 }
@@ -1297,6 +1289,15 @@
 		goto bail;
 	}
 
+	/* allocate dummy tail memory for all receive contexts */
+	dd->rcvhdrtail_dummy_kvaddr =
+		dma_alloc_coherent(&dd->pcidev->dev, sizeof(u64),
+				   &dd->rcvhdrtail_dummy_dma, GFP_KERNEL);
+	if (!dd->rcvhdrtail_dummy_kvaddr) {
+		ret = -ENOMEM;
+		goto bail;
+	}
+
 	atomic_set(&dd->ipoib_rsm_usr_num, 0);
 	return dd;
 
@@ -1504,13 +1505,6 @@
 
 	free_credit_return(dd);
 
-	if (dd->rcvhdrtail_dummy_kvaddr) {
-		dma_free_coherent(&dd->pcidev->dev, sizeof(u64),
-				  (void *)dd->rcvhdrtail_dummy_kvaddr,
-				  dd->rcvhdrtail_dummy_dma);
-		dd->rcvhdrtail_dummy_kvaddr = NULL;
-	}
-
 	/*
 	 * Free any resources still in use (usually just kernel contexts)
 	 * at unload; we do for ctxtcnt, because that's what we allocate.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/ipoib_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/ipoib_main.c
@@ -22,26 +22,35 @@
 	int ret;
 
 	dev->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
+	if (!dev->tstats)
+		return -ENOMEM;
 
 	ret = priv->netdev_ops->ndo_init(dev);
 	if (ret)
-		return ret;
+		goto out_ret;
 
 	ret = hfi1_netdev_add_data(priv->dd,
 				   qpn_from_mac(priv->netdev->dev_addr),
 				   dev);
 	if (ret < 0) {
 		priv->netdev_ops->ndo_uninit(dev);
-		return ret;
+		goto out_ret;
 	}
 
 	return 0;
+out_ret:
+	free_percpu(dev->tstats);
+	dev->tstats = NULL;
+	return ret;
 }
 
 static void hfi1_ipoib_dev_uninit(struct net_device *dev)
 {
 	struct hfi1_ipoib_dev_priv *priv = hfi1_ipoib_priv(dev);
 
+	free_percpu(dev->tstats);
+	dev->tstats = NULL;
+
 	hfi1_netdev_remove_data(priv->dd, qpn_from_mac(priv->netdev->dev_addr));
 
 	priv->netdev_ops->ndo_uninit(dev);
@@ -166,12 +175,7 @@
 	hfi1_ipoib_rxq_deinit(priv->netdev);
 
 	free_percpu(dev->tstats);
-}
-
-static void hfi1_ipoib_free_rdma_netdev(struct net_device *dev)
-{
-	hfi1_ipoib_netdev_dtor(dev);
-	free_netdev(dev);
+	dev->tstats = NULL;
 }
 
 static void hfi1_ipoib_set_id(struct net_device *dev, int id)
@@ -211,24 +215,23 @@
 	priv->port_num = port_num;
 	priv->netdev_ops = netdev->netdev_ops;
 
-	netdev->netdev_ops = &hfi1_ipoib_netdev_ops;
-
 	ib_query_pkey(device, port_num, priv->pkey_index, &priv->pkey);
 
 	rc = hfi1_ipoib_txreq_init(priv);
 	if (rc) {
 		dd_dev_err(dd, "IPoIB netdev TX init - failed(%d)\n", rc);
-		hfi1_ipoib_free_rdma_netdev(netdev);
 		return rc;
 	}
 
 	rc = hfi1_ipoib_rxq_init(netdev);
 	if (rc) {
 		dd_dev_err(dd, "IPoIB netdev RX init - failed(%d)\n", rc);
-		hfi1_ipoib_free_rdma_netdev(netdev);
+		hfi1_ipoib_txreq_deinit(priv);
 		return rc;
 	}
 
+	netdev->netdev_ops = &hfi1_ipoib_netdev_ops;
+
 	netdev->priv_destructor = hfi1_ipoib_netdev_dtor;
 	netdev->needs_free_netdev = true;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/ipoib_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/ipoib_tx.c
@@ -254,7 +254,8 @@
 				      txreq,
 				      skb_frag_page(frag),
 				      frag->bv_offset,
-				      skb_frag_size(frag));
+				      skb_frag_size(frag),
+				      NULL, NULL, NULL);
 		if (unlikely(ret))
 			break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/mmu_rb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/mmu_rb.c
@@ -19,8 +19,7 @@
 		const struct mmu_notifier_range *);
 static struct mmu_rb_node *__mmu_rb_search(struct mmu_rb_handler *,
 					   unsigned long, unsigned long);
-static void do_remove(struct mmu_rb_handler *handler,
-		      struct list_head *del_list);
+static void release_immediate(struct kref *refcount);
 static void handle_remove(struct work_struct *work);
 
 static const struct mmu_notifier_ops mn_opts = {
@@ -80,6 +79,9 @@
 	unsigned long flags;
 	struct list_head del_list;
 
+	/* Prevent freeing of mm until we are completely finished. */
+	mmgrab(handler->mn.mm);
+
 	/* Unregister first so we don't get any more notifications. */
 	mmu_notifier_unregister(&handler->mn, handler->mn.mm);
 
@@ -100,7 +102,14 @@
 	}
 	spin_unlock_irqrestore(&handler->lock, flags);
 
-	do_remove(handler, &del_list);
+	while (!list_empty(&del_list)) {
+		rbnode = list_first_entry(&del_list, struct mmu_rb_node, list);
+		list_del(&rbnode->list);
+		kref_put(&rbnode->refcount, release_immediate);
+	}
+
+	/* Now the mm may be freed. */
+	mmdrop(handler->mn.mm);
 
 	kfree(handler);
 }
@@ -120,17 +129,11 @@
 	spin_lock_irqsave(&handler->lock, flags);
 	node = __mmu_rb_search(handler, mnode->addr, mnode->len);
 	if (node) {
-		ret = -EINVAL;
+		ret = -EEXIST;
 		goto unlock;
 	}
 	__mmu_int_rb_insert(mnode, &handler->root);
-	list_add(&mnode->list, &handler->lru_list);
-
-	ret = handler->ops->insert(handler->ops_arg, mnode);
-	if (ret) {
-		__mmu_int_rb_remove(mnode, &handler->root);
-		list_del(&mnode->list); /* remove from LRU list */
-	}
+	list_add_tail(&mnode->list, &handler->lru_list);
 	mnode->handler = handler;
 unlock:
 	spin_unlock_irqrestore(&handler->lock, flags);
@@ -138,6 +141,19 @@
 }
 
 /* Caller must hold handler lock */
+struct mmu_rb_node *hfi1_mmu_rb_get_first(struct mmu_rb_handler *handler,
+					  unsigned long addr, unsigned long len)
+{
+	struct mmu_rb_node *node;
+
+	trace_hfi1_mmu_rb_search(addr, len);
+	node = __mmu_int_rb_iter_first(&handler->root, addr, (addr + len) - 1);
+	if (node)
+		list_move_tail(&node->list, &handler->lru_list);
+	return node;
+}
+
+/* Caller must hold handler lock */
 static struct mmu_rb_node *__mmu_rb_search(struct mmu_rb_handler *handler,
 					   unsigned long addr,
 					   unsigned long len)
@@ -161,30 +177,46 @@
 	return node;
 }
 
-bool hfi1_mmu_rb_remove_unless_exact(struct mmu_rb_handler *handler,
-				     unsigned long addr, unsigned long len,
-				     struct mmu_rb_node **rb_node)
+/*
+ * Must NOT call while holding mnode->handler->lock.
+ * mnode->handler->ops->remove() may sleep and mnode->handler->lock is a
+ * spinlock.
+ */
+static void release_immediate(struct kref *refcount)
 {
-	struct mmu_rb_node *node;
-	unsigned long flags;
-	bool ret = false;
+	struct mmu_rb_node *mnode =
+		container_of(refcount, struct mmu_rb_node, refcount);
+	mnode->handler->ops->remove(mnode->handler->ops_arg, mnode);
+}
 
-	if (current->mm != handler->mn.mm)
-		return ret;
+/* Caller must hold mnode->handler->lock */
+static void release_nolock(struct kref *refcount)
+{
+	struct mmu_rb_node *mnode =
+		container_of(refcount, struct mmu_rb_node, refcount);
+	list_move(&mnode->list, &mnode->handler->del_list);
+	queue_work(mnode->handler->wq, &mnode->handler->del_work);
+}
+
+/*
+ * struct mmu_rb_node->refcount kref_put() callback.
+ * Adds mmu_rb_node to mmu_rb_node->handler->del_list and queues
+ * handler->del_work on handler->wq.
+ * Does not remove mmu_rb_node from handler->lru_list or handler->rb_root.
+ * Acquires mmu_rb_node->handler->lock; do not call while already holding
+ * handler->lock.
+ */
+void hfi1_mmu_rb_release(struct kref *refcount)
+{
+	struct mmu_rb_node *mnode =
+		container_of(refcount, struct mmu_rb_node, refcount);
+	struct mmu_rb_handler *handler = mnode->handler;
+	unsigned long flags;
 
 	spin_lock_irqsave(&handler->lock, flags);
-	node = __mmu_rb_search(handler, addr, len);
-	if (node) {
-		if (node->addr == addr && node->len == len)
-			goto unlock;
-		__mmu_int_rb_remove(node, &handler->root);
-		list_del(&node->list); /* remove from LRU list */
-		ret = true;
-	}
-unlock:
+	list_move(&mnode->list, &mnode->handler->del_list);
 	spin_unlock_irqrestore(&handler->lock, flags);
-	*rb_node = node;
-	return ret;
+	queue_work(handler->wq, &handler->del_work);
 }
 
 void hfi1_mmu_rb_evict(struct mmu_rb_handler *handler, void *evict_arg)
@@ -200,8 +232,11 @@
 	INIT_LIST_HEAD(&del_list);
 
 	spin_lock_irqsave(&handler->lock, flags);
-	list_for_each_entry_safe_reverse(rbnode, ptr, &handler->lru_list,
-					 list) {
+	list_for_each_entry_safe(rbnode, ptr, &handler->lru_list, list) {
+		/* refcount == 1 implies mmu_rb_handler has only rbnode ref */
+		if (kref_read(&rbnode->refcount) > 1)
+			continue;
+
 		if (handler->ops->evict(handler->ops_arg, rbnode, evict_arg,
 					&stop)) {
 			__mmu_int_rb_remove(rbnode, &handler->root);
@@ -213,36 +248,11 @@
 	}
 	spin_unlock_irqrestore(&handler->lock, flags);
 
-	while (!list_empty(&del_list)) {
-		rbnode = list_first_entry(&del_list, struct mmu_rb_node, list);
-		list_del(&rbnode->list);
-		handler->ops->remove(handler->ops_arg, rbnode);
+	list_for_each_entry_safe(rbnode, ptr, &del_list, list) {
+		kref_put(&rbnode->refcount, release_immediate);
 	}
 }
 
-/*
- * It is up to the caller to ensure that this function does not race with the
- * mmu invalidate notifier which may be calling the users remove callback on
- * 'node'.
- */
-void hfi1_mmu_rb_remove(struct mmu_rb_handler *handler,
-			struct mmu_rb_node *node)
-{
-	unsigned long flags;
-
-	if (current->mm != handler->mn.mm)
-		return;
-
-	/* Validity of handler and node pointers has been checked by caller. */
-	trace_hfi1_mmu_rb_remove(node->addr, node->len);
-	spin_lock_irqsave(&handler->lock, flags);
-	__mmu_int_rb_remove(node, &handler->root);
-	list_del(&node->list); /* remove from LRU list */
-	spin_unlock_irqrestore(&handler->lock, flags);
-
-	handler->ops->remove(handler->ops_arg, node);
-}
-
 static int mmu_notifier_range_start(struct mmu_notifier *mn,
 		const struct mmu_notifier_range *range)
 {
@@ -251,7 +261,6 @@
 	struct rb_root_cached *root = &handler->root;
 	struct mmu_rb_node *node, *ptr = NULL;
 	unsigned long flags;
-	bool added = false;
 
 	spin_lock_irqsave(&handler->lock, flags);
 	for (node = __mmu_int_rb_iter_first(root, range->start, range->end-1);
@@ -260,39 +269,17 @@
 		ptr = __mmu_int_rb_iter_next(node, range->start,
 					     range->end - 1);
 		trace_hfi1_mmu_mem_invalidate(node->addr, node->len);
-		if (handler->ops->invalidate(handler->ops_arg, node)) {
-			__mmu_int_rb_remove(node, root);
-			/* move from LRU list to delete list */
-			list_move(&node->list, &handler->del_list);
-			added = true;
-		}
+		/* Remove from rb tree and lru_list. */
+		__mmu_int_rb_remove(node, root);
+		list_del_init(&node->list);
+		kref_put(&node->refcount, release_nolock);
 	}
 	spin_unlock_irqrestore(&handler->lock, flags);
 
-	if (added)
-		queue_work(handler->wq, &handler->del_work);
-
 	return 0;
 }
 
 /*
- * Call the remove function for the given handler and the list.  This
- * is expected to be called with a delete list extracted from handler.
- * The caller should not be holding the handler lock.
- */
-static void do_remove(struct mmu_rb_handler *handler,
-		      struct list_head *del_list)
-{
-	struct mmu_rb_node *node;
-
-	while (!list_empty(del_list)) {
-		node = list_first_entry(del_list, struct mmu_rb_node, list);
-		list_del(&node->list);
-		handler->ops->remove(handler->ops_arg, node);
-	}
-}
-
-/*
  * Work queue function to remove all nodes that have been queued up to
  * be removed.  The key feature is that mm->mmap_lock is not being held
  * and the remove callback can sleep while taking it, if needed.
@@ -304,11 +291,16 @@
 						del_work);
 	struct list_head del_list;
 	unsigned long flags;
+	struct mmu_rb_node *node;
 
 	/* remove anything that is queued to get removed */
 	spin_lock_irqsave(&handler->lock, flags);
 	list_replace_init(&handler->del_list, &del_list);
 	spin_unlock_irqrestore(&handler->lock, flags);
 
-	do_remove(handler, &del_list);
+	while (!list_empty(&del_list)) {
+		node = list_first_entry(&del_list, struct mmu_rb_node, list);
+		list_del(&node->list);
+		handler->ops->remove(handler->ops_arg, node);
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/mmu_rb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/mmu_rb.h
@@ -16,6 +16,7 @@
 	struct rb_node node;
 	struct mmu_rb_handler *handler;
 	struct list_head list;
+	struct kref refcount;
 };
 
 /*
@@ -51,11 +52,11 @@
 void hfi1_mmu_rb_unregister(struct mmu_rb_handler *handler);
 int hfi1_mmu_rb_insert(struct mmu_rb_handler *handler,
 		       struct mmu_rb_node *mnode);
+void hfi1_mmu_rb_release(struct kref *refcount);
+
 void hfi1_mmu_rb_evict(struct mmu_rb_handler *handler, void *evict_arg);
-void hfi1_mmu_rb_remove(struct mmu_rb_handler *handler,
-			struct mmu_rb_node *mnode);
-bool hfi1_mmu_rb_remove_unless_exact(struct mmu_rb_handler *handler,
-				     unsigned long addr, unsigned long len,
-				     struct mmu_rb_node **rb_node);
+struct mmu_rb_node *hfi1_mmu_rb_get_first(struct mmu_rb_handler *handler,
+					  unsigned long addr,
+					  unsigned long len);
 
 #endif /* _HFI1_MMU_RB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/pcie.c
@@ -3,6 +3,7 @@
  * Copyright(c) 2015 - 2019 Intel Corporation.
  */
 
+#include <linux/bitfield.h>
 #include <linux/pci.h>
 #include <linux/io.h>
 #include <linux/delay.h>
@@ -212,12 +213,6 @@
 	return speed;
 }
 
-/* return the PCIe link speed from the given link status */
-static u32 extract_width(u16 linkstat)
-{
-	return (linkstat & PCI_EXP_LNKSTA_NLW) >> PCI_EXP_LNKSTA_NLW_SHIFT;
-}
-
 /* read the link status and set dd->{lbus_width,lbus_speed,lbus_info} */
 static void update_lbus_info(struct hfi1_devdata *dd)
 {
@@ -230,7 +225,7 @@
 		return;
 	}
 
-	dd->lbus_width = extract_width(linkstat);
+	dd->lbus_width = FIELD_GET(PCI_EXP_LNKSTA_NLW, linkstat);
 	dd->lbus_speed = extract_speed(linkstat);
 	snprintf(dd->lbus_info, sizeof(dd->lbus_info),
 		 "PCIe,%uMHz,x%u", dd->lbus_speed, dd->lbus_width);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/pio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/pio.c
@@ -913,8 +913,7 @@
 	spin_unlock(&sc->release_lock);
 
 	write_seqlock(&sc->waitlock);
-	if (!list_empty(&sc->piowait))
-		list_move(&sc->piowait, &wake_list);
+	list_splice_init(&sc->piowait, &wake_list);
 	write_sequnlock(&sc->waitlock);
 	while (!list_empty(&wake_list)) {
 		struct iowait *wait;
@@ -2090,7 +2089,7 @@
 				   "Unable to allocate credit return DMA range for NUMA %d\n",
 				   i);
 			ret = -ENOMEM;
-			goto done;
+			goto free_cr_base;
 		}
 	}
 	set_dev_node(&dd->pcidev->dev, dd->node);
@@ -2098,6 +2097,10 @@
 	ret = 0;
 done:
 	return ret;
+
+free_cr_base:
+	free_credit_return(dd);
+	goto done;
 }
 
 void free_credit_return(struct hfi1_devdata *dd)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/sdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/sdma.c
@@ -838,8 +838,8 @@
 	if (current->nr_cpus_allowed != 1)
 		goto out;
 
-	cpu_id = smp_processor_id();
 	rcu_read_lock();
+	cpu_id = smp_processor_id();
 	rht_node = rhashtable_lookup(dd->sdma_rht, &cpu_id,
 				     sdma_rht_params);
 
@@ -1288,11 +1288,13 @@
 		kvfree(sde->tx_ring);
 		sde->tx_ring = NULL;
 	}
-	spin_lock_irq(&dd->sde_map_lock);
-	sdma_map_free(rcu_access_pointer(dd->sdma_map));
-	RCU_INIT_POINTER(dd->sdma_map, NULL);
-	spin_unlock_irq(&dd->sde_map_lock);
-	synchronize_rcu();
+	if (rcu_access_pointer(dd->sdma_map)) {
+		spin_lock_irq(&dd->sde_map_lock);
+		sdma_map_free(rcu_access_pointer(dd->sdma_map));
+		RCU_INIT_POINTER(dd->sdma_map, NULL);
+		spin_unlock_irq(&dd->sde_map_lock);
+		synchronize_rcu();
+	}
 	kfree(dd->per_sdma);
 	dd->per_sdma = NULL;
 
@@ -1593,20 +1595,18 @@
 {
 	switch (sdma_mapping_type(descp)) {
 	case SDMA_MAP_SINGLE:
-		dma_unmap_single(
-			&dd->pcidev->dev,
-			sdma_mapping_addr(descp),
-			sdma_mapping_len(descp),
-			DMA_TO_DEVICE);
+		dma_unmap_single(&dd->pcidev->dev, sdma_mapping_addr(descp),
+				 sdma_mapping_len(descp), DMA_TO_DEVICE);
 		break;
 	case SDMA_MAP_PAGE:
-		dma_unmap_page(
-			&dd->pcidev->dev,
-			sdma_mapping_addr(descp),
-			sdma_mapping_len(descp),
-			DMA_TO_DEVICE);
+		dma_unmap_page(&dd->pcidev->dev, sdma_mapping_addr(descp),
+			       sdma_mapping_len(descp), DMA_TO_DEVICE);
 		break;
 	}
+
+	if (descp->pinning_ctx && descp->ctx_put)
+		descp->ctx_put(descp->pinning_ctx);
+	descp->pinning_ctx = NULL;
 }
 
 /*
@@ -3127,7 +3127,7 @@
 		/* Add descriptor for coalesce buffer */
 		tx->desc_limit = MAX_DESC;
 		return _sdma_txadd_daddr(dd, SDMA_MAP_SINGLE, tx,
-					 addr, tx->tlen);
+					 addr, tx->tlen, NULL, NULL, NULL);
 	}
 
 	return 1;
@@ -3158,7 +3158,6 @@
 {
 	int rval = 0;
 
-	tx->num_desc++;
 	if ((unlikely(tx->num_desc == tx->desc_limit))) {
 		rval = _extend_sdma_tx_descs(dd, tx);
 		if (rval) {
@@ -3166,12 +3165,15 @@
 			return rval;
 		}
 	}
+
 	/* finish the one just added */
 	make_tx_sdma_desc(
 		tx,
 		SDMA_MAP_NONE,
 		dd->sdma_pad_phys,
-		sizeof(u32) - (tx->packet_len & (sizeof(u32) - 1)));
+		sizeof(u32) - (tx->packet_len & (sizeof(u32) - 1)),
+		NULL, NULL, NULL);
+	tx->num_desc++;
 	_sdma_close_tx(dd, tx);
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/sdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/sdma.h
@@ -595,7 +595,10 @@
 	struct sdma_txreq *tx,
 	int type,
 	dma_addr_t addr,
-	size_t len)
+	size_t len,
+	void *pinning_ctx,
+	void (*ctx_get)(void *),
+	void (*ctx_put)(void *))
 {
 	struct sdma_desc *desc = &tx->descp[tx->num_desc];
 
@@ -612,6 +615,11 @@
 				<< SDMA_DESC0_PHY_ADDR_SHIFT) |
 			(((u64)len & SDMA_DESC0_BYTE_COUNT_MASK)
 				<< SDMA_DESC0_BYTE_COUNT_SHIFT);
+
+	desc->pinning_ctx = pinning_ctx;
+	desc->ctx_put = ctx_put;
+	if (pinning_ctx && ctx_get)
+		ctx_get(pinning_ctx);
 }
 
 /* helper to extend txreq */
@@ -631,14 +639,13 @@
 static inline void _sdma_close_tx(struct hfi1_devdata *dd,
 				  struct sdma_txreq *tx)
 {
-	tx->descp[tx->num_desc].qw[0] |=
-		SDMA_DESC0_LAST_DESC_FLAG;
-	tx->descp[tx->num_desc].qw[1] |=
-		dd->default_desc1;
+	u16 last_desc = tx->num_desc - 1;
+
+	tx->descp[last_desc].qw[0] |= SDMA_DESC0_LAST_DESC_FLAG;
+	tx->descp[last_desc].qw[1] |= dd->default_desc1;
 	if (tx->flags & SDMA_TXREQ_F_URGENT)
-		tx->descp[tx->num_desc].qw[1] |=
-			(SDMA_DESC1_HEAD_TO_HOST_FLAG |
-			 SDMA_DESC1_INT_REQ_FLAG);
+		tx->descp[last_desc].qw[1] |= (SDMA_DESC1_HEAD_TO_HOST_FLAG |
+					       SDMA_DESC1_INT_REQ_FLAG);
 }
 
 static inline int _sdma_txadd_daddr(
@@ -646,15 +653,20 @@
 	int type,
 	struct sdma_txreq *tx,
 	dma_addr_t addr,
-	u16 len)
+	u16 len,
+	void *pinning_ctx,
+	void (*ctx_get)(void *),
+	void (*ctx_put)(void *))
 {
 	int rval = 0;
 
 	make_tx_sdma_desc(
 		tx,
 		type,
-		addr, len);
+		addr, len,
+		pinning_ctx, ctx_get, ctx_put);
 	WARN_ON(len > tx->tlen);
+	tx->num_desc++;
 	tx->tlen -= len;
 	/* special cases for last */
 	if (!tx->tlen) {
@@ -666,7 +678,6 @@
 			_sdma_close_tx(dd, tx);
 		}
 	}
-	tx->num_desc++;
 	return rval;
 }
 
@@ -677,6 +688,14 @@
  * @page: page to map
  * @offset: offset within the page
  * @len: length in bytes
+ * @pinning_ctx: context to be stored on struct sdma_desc .pinning_ctx. Not
+ *               added if coalesce buffer is used. E.g. pointer to pinned-page
+ *               cache entry for the sdma_desc.
+ * @ctx_get: optional function to take reference to @pinning_ctx. Not called if
+ *           @pinning_ctx is NULL.
+ * @ctx_put: optional function to release reference to @pinning_ctx after
+ *           sdma_desc completes. May be called in interrupt context so must
+ *           not sleep. Not called if @pinning_ctx is NULL.
  *
  * This is used to add a page/offset/length descriptor.
  *
@@ -691,7 +710,10 @@
 	struct sdma_txreq *tx,
 	struct page *page,
 	unsigned long offset,
-	u16 len)
+	u16 len,
+	void *pinning_ctx,
+	void (*ctx_get)(void *),
+	void (*ctx_put)(void *))
 {
 	dma_addr_t addr;
 	int rval;
@@ -715,8 +737,8 @@
 		return -ENOSPC;
 	}
 
-	return _sdma_txadd_daddr(
-			dd, SDMA_MAP_PAGE, tx, addr, len);
+	return _sdma_txadd_daddr(dd, SDMA_MAP_PAGE, tx, addr, len,
+				 pinning_ctx, ctx_get, ctx_put);
 }
 
 /**
@@ -750,7 +772,8 @@
 			return rval;
 	}
 
-	return _sdma_txadd_daddr(dd, SDMA_MAP_NONE, tx, addr, len);
+	return _sdma_txadd_daddr(dd, SDMA_MAP_NONE, tx, addr, len,
+				 NULL, NULL, NULL);
 }
 
 /**
@@ -796,8 +819,8 @@
 		return -ENOSPC;
 	}
 
-	return _sdma_txadd_daddr(
-			dd, SDMA_MAP_SINGLE, tx, addr, len);
+	return _sdma_txadd_daddr(dd, SDMA_MAP_SINGLE, tx, addr, len,
+				 NULL, NULL, NULL);
 }
 
 struct iowait_work;
@@ -1030,5 +1053,4 @@
 extern uint mod_num_sdma;
 
 void sdma_update_lmc(struct hfi1_devdata *dd, u64 mask, u32 lid);
-
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/sdma_txreq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/sdma_txreq.h
@@ -19,6 +19,9 @@
 struct sdma_desc {
 	/* private:  don't use directly */
 	u64 qw[2];
+	void *pinning_ctx;
+	/* Release reference to @pinning_ctx. May be called in interrupt context. Must not sleep. */
+	void (*ctx_put)(void *ctx);
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/trace_mmu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/trace_mmu.h
@@ -37,10 +37,6 @@
 	     TP_PROTO(unsigned long addr, unsigned long len),
 	     TP_ARGS(addr, len));
 
-DEFINE_EVENT(hfi1_mmu_rb_template, hfi1_mmu_rb_remove,
-	     TP_PROTO(unsigned long addr, unsigned long len),
-	     TP_ARGS(addr, len));
-
 DEFINE_EVENT(hfi1_mmu_rb_template, hfi1_mmu_mem_invalidate,
 	     TP_PROTO(unsigned long addr, unsigned long len),
 	     TP_ARGS(addr, len));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/user_exp_rcv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/user_exp_rcv.c
@@ -23,18 +23,25 @@
 static bool tid_rb_invalidate(struct mmu_interval_notifier *mni,
 			      const struct mmu_notifier_range *range,
 			      unsigned long cur_seq);
+static bool tid_cover_invalidate(struct mmu_interval_notifier *mni,
+			         const struct mmu_notifier_range *range,
+			         unsigned long cur_seq);
 static int program_rcvarray(struct hfi1_filedata *fd, struct tid_user_buf *,
 			    struct tid_group *grp,
 			    unsigned int start, u16 count,
 			    u32 *tidlist, unsigned int *tididx,
 			    unsigned int *pmapped);
-static int unprogram_rcvarray(struct hfi1_filedata *fd, u32 tidinfo,
-			      struct tid_group **grp);
+static int unprogram_rcvarray(struct hfi1_filedata *fd, u32 tidinfo);
+static void __clear_tid_node(struct hfi1_filedata *fd,
+			     struct tid_rb_node *node);
 static void clear_tid_node(struct hfi1_filedata *fd, struct tid_rb_node *node);
 
 static const struct mmu_interval_notifier_ops tid_mn_ops = {
 	.invalidate = tid_rb_invalidate,
 };
+static const struct mmu_interval_notifier_ops tid_cover_ops = {
+	.invalidate = tid_cover_invalidate,
+};
 
 /*
  * Initialize context and file private data needed for Expected
@@ -153,16 +160,11 @@
 static int pin_rcv_pages(struct hfi1_filedata *fd, struct tid_user_buf *tidbuf)
 {
 	int pinned;
-	unsigned int npages;
+	unsigned int npages = tidbuf->npages;
 	unsigned long vaddr = tidbuf->vaddr;
 	struct page **pages = NULL;
 	struct hfi1_devdata *dd = fd->uctxt->dd;
 
-	/* Get the number of pages the user buffer spans */
-	npages = num_user_pages(vaddr, tidbuf->length);
-	if (!npages)
-		return -EINVAL;
-
 	if (npages > fd->uctxt->expected_count) {
 		dd_dev_err(dd, "Expected buffer too big\n");
 		return -EINVAL;
@@ -189,7 +191,6 @@
 		return pinned;
 	}
 	tidbuf->pages = pages;
-	tidbuf->npages = npages;
 	fd->tid_n_pinned += pinned;
 	return pinned;
 }
@@ -253,53 +254,66 @@
 		tididx = 0, mapped, mapped_pages = 0;
 	u32 *tidlist = NULL;
 	struct tid_user_buf *tidbuf;
+	unsigned long mmu_seq = 0;
 
 	if (!PAGE_ALIGNED(tinfo->vaddr))
 		return -EINVAL;
+	if (tinfo->length == 0)
+		return -EINVAL;
 
 	tidbuf = kzalloc(sizeof(*tidbuf), GFP_KERNEL);
 	if (!tidbuf)
 		return -ENOMEM;
 
+	mutex_init(&tidbuf->cover_mutex);
 	tidbuf->vaddr = tinfo->vaddr;
 	tidbuf->length = tinfo->length;
+	tidbuf->npages = num_user_pages(tidbuf->vaddr, tidbuf->length);
 	tidbuf->psets = kcalloc(uctxt->expected_count, sizeof(*tidbuf->psets),
 				GFP_KERNEL);
 	if (!tidbuf->psets) {
-		kfree(tidbuf);
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto fail_release_mem;
+	}
+
+	if (fd->use_mn) {
+		ret = mmu_interval_notifier_insert(
+			&tidbuf->notifier, current->mm,
+			tidbuf->vaddr, tidbuf->npages * PAGE_SIZE,
+			&tid_cover_ops);
+		if (ret)
+			goto fail_release_mem;
+		mmu_seq = mmu_interval_read_begin(&tidbuf->notifier);
 	}
 
 	pinned = pin_rcv_pages(fd, tidbuf);
 	if (pinned <= 0) {
-		kfree(tidbuf->psets);
-		kfree(tidbuf);
-		return pinned;
+		ret = (pinned < 0) ? pinned : -ENOSPC;
+		goto fail_unpin;
 	}
 
 	/* Find sets of physically contiguous pages */
 	tidbuf->n_psets = find_phys_blocks(tidbuf, pinned);
 
-	/*
-	 * We don't need to access this under a lock since tid_used is per
-	 * process and the same process cannot be in hfi1_user_exp_rcv_clear()
-	 * and hfi1_user_exp_rcv_setup() at the same time.
-	 */
+	/* Reserve the number of expected tids to be used. */
 	spin_lock(&fd->tid_lock);
 	if (fd->tid_used + tidbuf->n_psets > fd->tid_limit)
 		pageset_count = fd->tid_limit - fd->tid_used;
 	else
 		pageset_count = tidbuf->n_psets;
+	fd->tid_used += pageset_count;
 	spin_unlock(&fd->tid_lock);
 
-	if (!pageset_count)
-		goto bail;
+	if (!pageset_count) {
+		ret = -ENOSPC;
+		goto fail_unreserve;
+	}
 
 	ngroups = pageset_count / dd->rcv_entries.group_size;
 	tidlist = kcalloc(pageset_count, sizeof(*tidlist), GFP_KERNEL);
 	if (!tidlist) {
 		ret = -ENOMEM;
-		goto nomem;
+		goto fail_unreserve;
 	}
 
 	tididx = 0;
@@ -395,43 +409,78 @@
 	}
 unlock:
 	mutex_unlock(&uctxt->exp_mutex);
-nomem:
 	hfi1_cdbg(TID, "total mapped: tidpairs:%u pages:%u (%d)", tididx,
 		  mapped_pages, ret);
-	if (tididx) {
-		spin_lock(&fd->tid_lock);
-		fd->tid_used += tididx;
-		spin_unlock(&fd->tid_lock);
-		tinfo->tidcnt = tididx;
-		tinfo->length = mapped_pages * PAGE_SIZE;
 
-		if (copy_to_user(u64_to_user_ptr(tinfo->tidlist),
-				 tidlist, sizeof(tidlist[0]) * tididx)) {
-			/*
-			 * On failure to copy to the user level, we need to undo
-			 * everything done so far so we don't leak resources.
-			 */
-			tinfo->tidlist = (unsigned long)&tidlist;
-			hfi1_user_exp_rcv_clear(fd, tinfo);
-			tinfo->tidlist = 0;
-			ret = -EFAULT;
-			goto bail;
+	/* fail if nothing was programmed, set error if none provided */
+	if (tididx == 0) {
+		if (ret >= 0)
+			ret = -ENOSPC;
+		goto fail_unreserve;
+	}
+
+	/* adjust reserved tid_used to actual count */
+	spin_lock(&fd->tid_lock);
+	fd->tid_used -= pageset_count - tididx;
+	spin_unlock(&fd->tid_lock);
+
+	/* unpin all pages not covered by a TID */
+	unpin_rcv_pages(fd, tidbuf, NULL, mapped_pages, pinned - mapped_pages,
+			false);
+
+	if (fd->use_mn) {
+		/* check for an invalidate during setup */
+		bool fail = false;
+
+		mutex_lock(&tidbuf->cover_mutex);
+		fail = mmu_interval_read_retry(&tidbuf->notifier, mmu_seq);
+		mutex_unlock(&tidbuf->cover_mutex);
+
+		if (fail) {
+			ret = -EBUSY;
+			goto fail_unprogram;
 		}
 	}
 
-	/*
-	 * If not everything was mapped (due to insufficient RcvArray entries,
-	 * for example), unpin all unmapped pages so we can pin them nex time.
-	 */
-	if (mapped_pages != pinned)
-		unpin_rcv_pages(fd, tidbuf, NULL, mapped_pages,
-				(pinned - mapped_pages), false);
-bail:
+	tinfo->tidcnt = tididx;
+	tinfo->length = mapped_pages * PAGE_SIZE;
+
+	if (copy_to_user(u64_to_user_ptr(tinfo->tidlist),
+			 tidlist, sizeof(tidlist[0]) * tididx)) {
+		ret = -EFAULT;
+		goto fail_unprogram;
+	}
+
+	if (fd->use_mn)
+		mmu_interval_notifier_remove(&tidbuf->notifier);
+	kfree(tidbuf->pages);
 	kfree(tidbuf->psets);
+	kfree(tidbuf);
 	kfree(tidlist);
+	return 0;
+
+fail_unprogram:
+	/* unprogram, unmap, and unpin all allocated TIDs */
+	tinfo->tidlist = (unsigned long)tidlist;
+	hfi1_user_exp_rcv_clear(fd, tinfo);
+	tinfo->tidlist = 0;
+	pinned = 0;		/* nothing left to unpin */
+	pageset_count = 0;	/* nothing left reserved */
+fail_unreserve:
+	spin_lock(&fd->tid_lock);
+	fd->tid_used -= pageset_count;
+	spin_unlock(&fd->tid_lock);
+fail_unpin:
+	if (fd->use_mn)
+		mmu_interval_notifier_remove(&tidbuf->notifier);
+	if (pinned > 0)
+		unpin_rcv_pages(fd, tidbuf, NULL, 0, pinned, false);
+fail_release_mem:
 	kfree(tidbuf->pages);
+	kfree(tidbuf->psets);
 	kfree(tidbuf);
-	return ret > 0 ? 0 : ret;
+	kfree(tidlist);
+	return ret;
 }
 
 int hfi1_user_exp_rcv_clear(struct hfi1_filedata *fd,
@@ -452,7 +501,7 @@
 
 	mutex_lock(&uctxt->exp_mutex);
 	for (tididx = 0; tididx < tinfo->tidcnt; tididx++) {
-		ret = unprogram_rcvarray(fd, tidinfo[tididx], NULL);
+		ret = unprogram_rcvarray(fd, tidinfo[tididx]);
 		if (ret) {
 			hfi1_cdbg(TID, "Failed to unprogram rcv array %d",
 				  ret);
@@ -707,6 +756,7 @@
 	}
 
 	node->fdata = fd;
+	mutex_init(&node->invalidate_mutex);
 	node->phys = page_to_phys(pages[0]);
 	node->npages = npages;
 	node->rcventry = rcventry;
@@ -722,11 +772,6 @@
 			&tid_mn_ops);
 		if (ret)
 			goto out_unmap;
-		/*
-		 * FIXME: This is in the wrong order, the notifier should be
-		 * established before the pages are pinned by pin_rcv_pages.
-		 */
-		mmu_interval_read_begin(&node->notifier);
 	}
 	fd->entry_to_rb[node->rcventry - uctxt->expected_base] = node;
 
@@ -746,8 +791,7 @@
 	return -EFAULT;
 }
 
-static int unprogram_rcvarray(struct hfi1_filedata *fd, u32 tidinfo,
-			      struct tid_group **grp)
+static int unprogram_rcvarray(struct hfi1_filedata *fd, u32 tidinfo)
 {
 	struct hfi1_ctxtdata *uctxt = fd->uctxt;
 	struct hfi1_devdata *dd = uctxt->dd;
@@ -770,9 +814,6 @@
 	if (!node || node->rcventry != (uctxt->expected_base + rcventry))
 		return -EBADF;
 
-	if (grp)
-		*grp = node->grp;
-
 	if (fd->use_mn)
 		mmu_interval_notifier_remove(&node->notifier);
 	cacheless_tid_rb_remove(fd, node);
@@ -780,23 +821,34 @@
 	return 0;
 }
 
-static void clear_tid_node(struct hfi1_filedata *fd, struct tid_rb_node *node)
+static void __clear_tid_node(struct hfi1_filedata *fd, struct tid_rb_node *node)
 {
 	struct hfi1_ctxtdata *uctxt = fd->uctxt;
 	struct hfi1_devdata *dd = uctxt->dd;
 
+	mutex_lock(&node->invalidate_mutex);
+	if (node->freed)
+		goto done;
+	node->freed = true;
+
 	trace_hfi1_exp_tid_unreg(uctxt->ctxt, fd->subctxt, node->rcventry,
 				 node->npages,
 				 node->notifier.interval_tree.start, node->phys,
 				 node->dma_addr);
 
-	/*
-	 * Make sure device has seen the write before we unpin the
-	 * pages.
-	 */
+	/* Make sure device has seen the write before pages are unpinned */
 	hfi1_put_tid(dd, node->rcventry, PT_INVALID_FLUSH, 0, 0);
 
 	unpin_rcv_pages(fd, NULL, node, 0, node->npages, true);
+done:
+	mutex_unlock(&node->invalidate_mutex);
+}
+
+static void clear_tid_node(struct hfi1_filedata *fd, struct tid_rb_node *node)
+{
+	struct hfi1_ctxtdata *uctxt = fd->uctxt;
+
+	__clear_tid_node(fd, node);
 
 	node->grp->used--;
 	node->grp->map &= ~(1 << (node->rcventry - node->grp->base));
@@ -855,10 +907,16 @@
 	if (node->freed)
 		return true;
 
+	/* take action only if unmapping */
+	if (range->event != MMU_NOTIFY_UNMAP)
+		return true;
+
 	trace_hfi1_exp_tid_inval(uctxt->ctxt, fdata->subctxt,
 				 node->notifier.interval_tree.start,
 				 node->rcventry, node->npages, node->dma_addr);
-	node->freed = true;
+
+	/* clear the hardware rcvarray entry */
+	__clear_tid_node(fdata, node);
 
 	spin_lock(&fdata->invalid_lock);
 	if (fdata->invalid_tid_idx < uctxt->expected_count) {
@@ -888,6 +946,23 @@
 	return true;
 }
 
+static bool tid_cover_invalidate(struct mmu_interval_notifier *mni,
+			         const struct mmu_notifier_range *range,
+			         unsigned long cur_seq)
+{
+	struct tid_user_buf *tidbuf =
+		container_of(mni, struct tid_user_buf, notifier);
+
+	/* take action only if unmapping */
+	if (range->event == MMU_NOTIFY_UNMAP) {
+		mutex_lock(&tidbuf->cover_mutex);
+		mmu_interval_set_seq(mni, cur_seq);
+		mutex_unlock(&tidbuf->cover_mutex);
+	}
+
+	return true;
+}
+
 static void cacheless_tid_rb_remove(struct hfi1_filedata *fdata,
 				    struct tid_rb_node *tnode)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/user_exp_rcv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/user_exp_rcv.h
@@ -16,6 +16,8 @@
 };
 
 struct tid_user_buf {
+	struct mmu_interval_notifier notifier;
+	struct mutex cover_mutex;
 	unsigned long vaddr;
 	unsigned long length;
 	unsigned int npages;
@@ -27,6 +29,7 @@
 struct tid_rb_node {
 	struct mmu_interval_notifier notifier;
 	struct hfi1_filedata *fdata;
+	struct mutex invalidate_mutex; /* covers hw removal */
 	unsigned long phys;
 	struct tid_group *grp;
 	u32 rcventry;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/user_pages.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/user_pages.c
@@ -29,33 +29,52 @@
 bool hfi1_can_pin_pages(struct hfi1_devdata *dd, struct mm_struct *mm,
 			u32 nlocked, u32 npages)
 {
-	unsigned long ulimit = rlimit(RLIMIT_MEMLOCK), pinned, cache_limit,
-		size = (cache_size * (1UL << 20)); /* convert to bytes */
-	unsigned int usr_ctxts =
-			dd->num_rcv_contexts - dd->first_dyn_alloc_ctxt;
-	bool can_lock = capable(CAP_IPC_LOCK);
+	unsigned long ulimit_pages;
+	unsigned long cache_limit_pages;
+	unsigned int usr_ctxts;
 
 	/*
-	 * Calculate per-cache size. The calculation below uses only a quarter
-	 * of the available per-context limit. This leaves space for other
-	 * pinning. Should we worry about shared ctxts?
+	 * Perform RLIMIT_MEMLOCK based checks unless CAP_IPC_LOCK is present.
 	 */
-	cache_limit = (ulimit / usr_ctxts) / 4;
+	if (!capable(CAP_IPC_LOCK)) {
+		ulimit_pages =
+			DIV_ROUND_DOWN_ULL(rlimit(RLIMIT_MEMLOCK), PAGE_SIZE);
+
+		/*
+		 * Pinning these pages would exceed this process's locked memory
+		 * limit.
+		 */
+		if (atomic64_read(&mm->pinned_vm) + npages > ulimit_pages)
+			return false;
+
+		/*
+		 * Only allow 1/4 of the user's RLIMIT_MEMLOCK to be used for HFI
+		 * caches.  This fraction is then equally distributed among all
+		 * existing user contexts.  Note that if RLIMIT_MEMLOCK is
+		 * 'unlimited' (-1), the value of this limit will be > 2^42 pages
+		 * (2^64 / 2^12 / 2^8 / 2^2).
+		 *
+		 * The effectiveness of this check may be reduced if I/O occurs on
+		 * some user contexts before all user contexts are created.  This
+		 * check assumes that this process is the only one using this
+		 * context (e.g., the corresponding fd was not passed to another
+		 * process for concurrent access) as there is no per-context,
+		 * per-process tracking of pinned pages.  It also assumes that each
+		 * user context has only one cache to limit.
+		 */
+		usr_ctxts = dd->num_rcv_contexts - dd->first_dyn_alloc_ctxt;
+		if (nlocked + npages > (ulimit_pages / usr_ctxts / 4))
+			return false;
+	}
 
-	/* If ulimit isn't set to "unlimited" and is smaller than cache_size. */
-	if (ulimit != (-1UL) && size > cache_limit)
-		size = cache_limit;
-
-	/* Convert to number of pages */
-	size = DIV_ROUND_UP(size, PAGE_SIZE);
-
-	pinned = atomic64_read(&mm->pinned_vm);
-
-	/* First, check the absolute limit against all pinned pages. */
-	if (pinned + npages >= ulimit && !can_lock)
+	/*
+	 * Pinning these pages would exceed the size limit for this cache.
+	 */
+	cache_limit_pages = cache_size * (1024 * 1024) / PAGE_SIZE;
+	if (nlocked + npages > cache_limit_pages)
 		return false;
 
-	return ((nlocked + npages) <= size) || can_lock;
+	return true;
 }
 
 int hfi1_acquire_user_pages(struct mm_struct *mm, unsigned long vaddr, size_t npages,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/user_sdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/user_sdma.c
@@ -24,7 +24,6 @@
 
 #include "hfi.h"
 #include "sdma.h"
-#include "mmu_rb.h"
 #include "user_sdma.h"
 #include "verbs.h"  /* for the headers */
 #include "common.h" /* for struct hfi1_tid_info */
@@ -39,11 +38,7 @@
 static int user_sdma_send_pkts(struct user_sdma_request *req, u16 maxpkts);
 static void user_sdma_txreq_cb(struct sdma_txreq *txreq, int status);
 static inline void pq_update(struct hfi1_user_sdma_pkt_q *pq);
-static void user_sdma_free_request(struct user_sdma_request *req, bool unpin);
-static int pin_vector_pages(struct user_sdma_request *req,
-			    struct user_sdma_iovec *iovec);
-static void unpin_vector_pages(struct mm_struct *mm, struct page **pages,
-			       unsigned start, unsigned npages);
+static void user_sdma_free_request(struct user_sdma_request *req);
 static int check_header_template(struct user_sdma_request *req,
 				 struct hfi1_pkt_header *hdr, u32 lrhlen,
 				 u32 datalen);
@@ -67,20 +62,21 @@
 static void activate_packet_queue(struct iowait *wait, int reason);
 static bool sdma_rb_filter(struct mmu_rb_node *node, unsigned long addr,
 			   unsigned long len);
-static int sdma_rb_insert(void *arg, struct mmu_rb_node *mnode);
 static int sdma_rb_evict(void *arg, struct mmu_rb_node *mnode,
 			 void *arg2, bool *stop);
 static void sdma_rb_remove(void *arg, struct mmu_rb_node *mnode);
-static int sdma_rb_invalidate(void *arg, struct mmu_rb_node *mnode);
 
 static struct mmu_rb_ops sdma_rb_ops = {
 	.filter = sdma_rb_filter,
-	.insert = sdma_rb_insert,
 	.evict = sdma_rb_evict,
 	.remove = sdma_rb_remove,
-	.invalidate = sdma_rb_invalidate
 };
 
+static int add_system_pages_to_sdma_packet(struct user_sdma_request *req,
+					   struct user_sdma_txreq *tx,
+					   struct user_sdma_iovec *iovec,
+					   u32 *pkt_remaining);
+
 static int defer_packet_queue(
 	struct sdma_engine *sde,
 	struct iowait_work *wait,
@@ -161,9 +157,7 @@
 	if (!pq->reqs)
 		goto pq_reqs_nomem;
 
-	pq->req_in_use = kcalloc(BITS_TO_LONGS(hfi1_sdma_comp_ring_size),
-				 sizeof(*pq->req_in_use),
-				 GFP_KERNEL);
+	pq->req_in_use = bitmap_zalloc(hfi1_sdma_comp_ring_size, GFP_KERNEL);
 	if (!pq->req_in_use)
 		goto pq_reqs_no_in_use;
 
@@ -210,7 +204,7 @@
 cq_nomem:
 	kmem_cache_destroy(pq->txreq_cache);
 pq_txreq_nomem:
-	kfree(pq->req_in_use);
+	bitmap_free(pq->req_in_use);
 pq_reqs_no_in_use:
 	kfree(pq->reqs);
 pq_reqs_nomem:
@@ -249,15 +243,15 @@
 		spin_unlock(&fd->pq_rcu_lock);
 		synchronize_srcu(&fd->pq_srcu);
 		/* at this point there can be no more new requests */
-		if (pq->handler)
-			hfi1_mmu_rb_unregister(pq->handler);
 		iowait_sdma_drain(&pq->busy);
 		/* Wait until all requests have been freed. */
 		wait_event_interruptible(
 			pq->wait,
 			!atomic_read(&pq->n_reqs));
 		kfree(pq->reqs);
-		kfree(pq->req_in_use);
+		if (pq->handler)
+			hfi1_mmu_rb_unregister(pq->handler);
+		bitmap_free(pq->req_in_use);
 		kmem_cache_destroy(pq->txreq_cache);
 		flush_pq_iowait(pq);
 		kfree(pq);
@@ -412,6 +406,7 @@
 		ret = -EINVAL;
 		goto free_req;
 	}
+
 	/* Copy the header from the user buffer */
 	ret = copy_from_user(&req->hdr, iovec[idx].iov_base + sizeof(info),
 			     sizeof(req->hdr));
@@ -486,9 +481,8 @@
 		memcpy(&req->iovs[i].iov,
 		       iovec + idx++,
 		       sizeof(req->iovs[i].iov));
-		ret = pin_vector_pages(req, &req->iovs[i]);
-		if (ret) {
-			req->data_iovs = i;
+		if (req->iovs[i].iov.iov_len == 0) {
+			ret = -EINVAL;
 			goto free_req;
 		}
 		req->data_len += req->iovs[i].iov.iov_len;
@@ -586,7 +580,7 @@
 		if (req->seqsubmitted)
 			wait_event(pq->busy.wait_dma,
 				   (req->seqcomp == req->seqsubmitted - 1));
-		user_sdma_free_request(req, true);
+		user_sdma_free_request(req);
 		pq_update(pq);
 		set_comp_state(pq, cq, info.comp_idx, ERROR, ret);
 	}
@@ -698,48 +692,6 @@
 	return ret;
 }
 
-static int user_sdma_txadd(struct user_sdma_request *req,
-			   struct user_sdma_txreq *tx,
-			   struct user_sdma_iovec *iovec, u32 datalen,
-			   u32 *queued_ptr, u32 *data_sent_ptr,
-			   u64 *iov_offset_ptr)
-{
-	int ret;
-	unsigned int pageidx, len;
-	unsigned long base, offset;
-	u64 iov_offset = *iov_offset_ptr;
-	u32 queued = *queued_ptr, data_sent = *data_sent_ptr;
-	struct hfi1_user_sdma_pkt_q *pq = req->pq;
-
-	base = (unsigned long)iovec->iov.iov_base;
-	offset = offset_in_page(base + iovec->offset + iov_offset);
-	pageidx = (((iovec->offset + iov_offset + base) - (base & PAGE_MASK)) >>
-		   PAGE_SHIFT);
-	len = offset + req->info.fragsize > PAGE_SIZE ?
-		PAGE_SIZE - offset : req->info.fragsize;
-	len = min((datalen - queued), len);
-	ret = sdma_txadd_page(pq->dd, &tx->txreq, iovec->pages[pageidx],
-			      offset, len);
-	if (ret) {
-		SDMA_DBG(req, "SDMA txreq add page failed %d\n", ret);
-		return ret;
-	}
-	iov_offset += len;
-	queued += len;
-	data_sent += len;
-	if (unlikely(queued < datalen && pageidx == iovec->npages &&
-		     req->iov_idx < req->data_iovs - 1)) {
-		iovec->offset += iov_offset;
-		iovec = &req->iovs[++req->iov_idx];
-		iov_offset = 0;
-	}
-
-	*queued_ptr = queued;
-	*data_sent_ptr = data_sent;
-	*iov_offset_ptr = iov_offset;
-	return ret;
-}
-
 static int user_sdma_send_pkts(struct user_sdma_request *req, u16 maxpkts)
 {
 	int ret = 0;
@@ -771,8 +723,7 @@
 		maxpkts = req->info.npkts - req->seqnum;
 
 	while (npkts < maxpkts) {
-		u32 datalen = 0, queued = 0, data_sent = 0;
-		u64 iov_offset = 0;
+		u32 datalen = 0;
 
 		/*
 		 * Check whether any of the completions have come back
@@ -865,27 +816,17 @@
 				goto free_txreq;
 		}
 
-		/*
-		 * If the request contains any data vectors, add up to
-		 * fragsize bytes to the descriptor.
-		 */
-		while (queued < datalen &&
-		       (req->sent + data_sent) < req->data_len) {
-			ret = user_sdma_txadd(req, tx, iovec, datalen,
-					      &queued, &data_sent, &iov_offset);
-			if (ret)
-				goto free_txreq;
-		}
-		/*
-		 * The txreq was submitted successfully so we can update
-		 * the counters.
-		 */
 		req->koffset += datalen;
 		if (req_opcode(req->info.ctrl) == EXPECTED)
 			req->tidoffset += datalen;
-		req->sent += data_sent;
-		if (req->data_len)
-			iovec->offset += iov_offset;
+		req->sent += datalen;
+		while (datalen) {
+			ret = add_system_pages_to_sdma_packet(req, tx, iovec,
+							      &datalen);
+			if (ret)
+				goto free_txreq;
+			iovec = &req->iovs[req->iov_idx];
+		}
 		list_add_tail(&tx->txreq.list, &req->txps);
 		/*
 		 * It is important to increment this here as it is used to
@@ -922,133 +863,14 @@
 static u32 sdma_cache_evict(struct hfi1_user_sdma_pkt_q *pq, u32 npages)
 {
 	struct evict_data evict_data;
+	struct mmu_rb_handler *handler = pq->handler;
 
 	evict_data.cleared = 0;
 	evict_data.target = npages;
-	hfi1_mmu_rb_evict(pq->handler, &evict_data);
+	hfi1_mmu_rb_evict(handler, &evict_data);
 	return evict_data.cleared;
 }
 
-static int pin_sdma_pages(struct user_sdma_request *req,
-			  struct user_sdma_iovec *iovec,
-			  struct sdma_mmu_node *node,
-			  int npages)
-{
-	int pinned, cleared;
-	struct page **pages;
-	struct hfi1_user_sdma_pkt_q *pq = req->pq;
-
-	pages = kcalloc(npages, sizeof(*pages), GFP_KERNEL);
-	if (!pages)
-		return -ENOMEM;
-	memcpy(pages, node->pages, node->npages * sizeof(*pages));
-
-	npages -= node->npages;
-retry:
-	if (!hfi1_can_pin_pages(pq->dd, current->mm,
-				atomic_read(&pq->n_locked), npages)) {
-		cleared = sdma_cache_evict(pq, npages);
-		if (cleared >= npages)
-			goto retry;
-	}
-	pinned = hfi1_acquire_user_pages(current->mm,
-					 ((unsigned long)iovec->iov.iov_base +
-					 (node->npages * PAGE_SIZE)), npages, 0,
-					 pages + node->npages);
-	if (pinned < 0) {
-		kfree(pages);
-		return pinned;
-	}
-	if (pinned != npages) {
-		unpin_vector_pages(current->mm, pages, node->npages, pinned);
-		return -EFAULT;
-	}
-	kfree(node->pages);
-	node->rb.len = iovec->iov.iov_len;
-	node->pages = pages;
-	atomic_add(pinned, &pq->n_locked);
-	return pinned;
-}
-
-static void unpin_sdma_pages(struct sdma_mmu_node *node)
-{
-	if (node->npages) {
-		unpin_vector_pages(mm_from_sdma_node(node), node->pages, 0,
-				   node->npages);
-		atomic_sub(node->npages, &node->pq->n_locked);
-	}
-}
-
-static int pin_vector_pages(struct user_sdma_request *req,
-			    struct user_sdma_iovec *iovec)
-{
-	int ret = 0, pinned, npages;
-	struct hfi1_user_sdma_pkt_q *pq = req->pq;
-	struct sdma_mmu_node *node = NULL;
-	struct mmu_rb_node *rb_node;
-	struct iovec *iov;
-	bool extracted;
-
-	extracted =
-		hfi1_mmu_rb_remove_unless_exact(pq->handler,
-						(unsigned long)
-						iovec->iov.iov_base,
-						iovec->iov.iov_len, &rb_node);
-	if (rb_node) {
-		node = container_of(rb_node, struct sdma_mmu_node, rb);
-		if (!extracted) {
-			atomic_inc(&node->refcount);
-			iovec->pages = node->pages;
-			iovec->npages = node->npages;
-			iovec->node = node;
-			return 0;
-		}
-	}
-
-	if (!node) {
-		node = kzalloc(sizeof(*node), GFP_KERNEL);
-		if (!node)
-			return -ENOMEM;
-
-		node->rb.addr = (unsigned long)iovec->iov.iov_base;
-		node->pq = pq;
-		atomic_set(&node->refcount, 0);
-	}
-
-	iov = &iovec->iov;
-	npages = num_user_pages((unsigned long)iov->iov_base, iov->iov_len);
-	if (node->npages < npages) {
-		pinned = pin_sdma_pages(req, iovec, node, npages);
-		if (pinned < 0) {
-			ret = pinned;
-			goto bail;
-		}
-		node->npages += pinned;
-		npages = node->npages;
-	}
-	iovec->pages = node->pages;
-	iovec->npages = npages;
-	iovec->node = node;
-
-	ret = hfi1_mmu_rb_insert(req->pq->handler, &node->rb);
-	if (ret) {
-		iovec->node = NULL;
-		goto bail;
-	}
-	return 0;
-bail:
-	unpin_sdma_pages(node);
-	kfree(node);
-	return ret;
-}
-
-static void unpin_vector_pages(struct mm_struct *mm, struct page **pages,
-			       unsigned start, unsigned npages)
-{
-	hfi1_release_user_pages(mm, pages + start, npages, false);
-	kfree(pages);
-}
-
 static int check_header_template(struct user_sdma_request *req,
 				 struct hfi1_pkt_header *hdr, u32 lrhlen,
 				 u32 datalen)
@@ -1390,7 +1212,7 @@
 	if (req->seqcomp != req->info.npkts - 1)
 		return;
 
-	user_sdma_free_request(req, false);
+	user_sdma_free_request(req);
 	set_comp_state(pq, cq, req->info.comp_idx, state, status);
 	pq_update(pq);
 }
@@ -1401,10 +1223,8 @@
 		wake_up(&pq->wait);
 }
 
-static void user_sdma_free_request(struct user_sdma_request *req, bool unpin)
+static void user_sdma_free_request(struct user_sdma_request *req)
 {
-	int i;
-
 	if (!list_empty(&req->txps)) {
 		struct sdma_txreq *t, *p;
 
@@ -1417,21 +1237,6 @@
 		}
 	}
 
-	for (i = 0; i < req->data_iovs; i++) {
-		struct sdma_mmu_node *node = req->iovs[i].node;
-
-		if (!node)
-			continue;
-
-		req->iovs[i].node = NULL;
-
-		if (unpin)
-			hfi1_mmu_rb_remove(req->pq->handler,
-					   &node->rb);
-		else
-			atomic_dec(&node->refcount);
-	}
-
 	kfree(req->tids);
 	clear_bit(req->info.comp_idx, req->pq->req_in_use);
 }
@@ -1449,21 +1254,374 @@
 					idx, state, ret);
 }
 
-static bool sdma_rb_filter(struct mmu_rb_node *node, unsigned long addr,
-			   unsigned long len)
+static void unpin_vector_pages(struct mm_struct *mm, struct page **pages,
+			       unsigned int start, unsigned int npages)
 {
-	return (bool)(node->addr == addr);
+	hfi1_release_user_pages(mm, pages + start, npages, false);
+	kfree(pages);
 }
 
-static int sdma_rb_insert(void *arg, struct mmu_rb_node *mnode)
+static void free_system_node(struct sdma_mmu_node *node)
 {
-	struct sdma_mmu_node *node =
-		container_of(mnode, struct sdma_mmu_node, rb);
+	if (node->npages) {
+		unpin_vector_pages(mm_from_sdma_node(node), node->pages, 0,
+				   node->npages);
+		atomic_sub(node->npages, &node->pq->n_locked);
+	}
+	kfree(node);
+}
+
+/*
+ * kref_get()'s an additional kref on the returned rb_node to prevent rb_node
+ * from being released until after rb_node is assigned to an SDMA descriptor
+ * (struct sdma_desc) under add_system_iovec_to_sdma_packet(), even if the
+ * virtual address range for rb_node is invalidated between now and then.
+ */
+static struct sdma_mmu_node *find_system_node(struct mmu_rb_handler *handler,
+					      unsigned long start,
+					      unsigned long end)
+{
+	struct mmu_rb_node *rb_node;
+	unsigned long flags;
+
+	spin_lock_irqsave(&handler->lock, flags);
+	rb_node = hfi1_mmu_rb_get_first(handler, start, (end - start));
+	if (!rb_node) {
+		spin_unlock_irqrestore(&handler->lock, flags);
+		return NULL;
+	}
+
+	/* "safety" kref to prevent release before add_system_iovec_to_sdma_packet() */
+	kref_get(&rb_node->refcount);
+	spin_unlock_irqrestore(&handler->lock, flags);
+
+	return container_of(rb_node, struct sdma_mmu_node, rb);
+}
+
+static int pin_system_pages(struct user_sdma_request *req,
+			    uintptr_t start_address, size_t length,
+			    struct sdma_mmu_node *node, int npages)
+{
+	struct hfi1_user_sdma_pkt_q *pq = req->pq;
+	int pinned, cleared;
+	struct page **pages;
+
+	pages = kcalloc(npages, sizeof(*pages), GFP_KERNEL);
+	if (!pages)
+		return -ENOMEM;
+
+retry:
+	if (!hfi1_can_pin_pages(pq->dd, current->mm, atomic_read(&pq->n_locked),
+				npages)) {
+		SDMA_DBG(req, "Evicting: nlocked %u npages %u",
+			 atomic_read(&pq->n_locked), npages);
+		cleared = sdma_cache_evict(pq, npages);
+		if (cleared >= npages)
+			goto retry;
+	}
+
+	SDMA_DBG(req, "Acquire user pages start_address %lx node->npages %u npages %u",
+		 start_address, node->npages, npages);
+	pinned = hfi1_acquire_user_pages(current->mm, start_address, npages, 0,
+					 pages);
+
+	if (pinned < 0) {
+		kfree(pages);
+		SDMA_DBG(req, "pinned %d", pinned);
+		return pinned;
+	}
+	if (pinned != npages) {
+		unpin_vector_pages(current->mm, pages, node->npages, pinned);
+		SDMA_DBG(req, "npages %u pinned %d", npages, pinned);
+		return -EFAULT;
+	}
+	node->rb.addr = start_address;
+	node->rb.len = length;
+	node->pages = pages;
+	node->npages = npages;
+	atomic_add(pinned, &pq->n_locked);
+	SDMA_DBG(req, "done. pinned %d", pinned);
+	return 0;
+}
+
+/*
+ * kref refcount on *node_p will be 2 on successful addition: one kref from
+ * kref_init() for mmu_rb_handler and one kref to prevent *node_p from being
+ * released until after *node_p is assigned to an SDMA descriptor (struct
+ * sdma_desc) under add_system_iovec_to_sdma_packet(), even if the virtual
+ * address range for *node_p is invalidated between now and then.
+ */
+static int add_system_pinning(struct user_sdma_request *req,
+			      struct sdma_mmu_node **node_p,
+			      unsigned long start, unsigned long len)
+
+{
+	struct hfi1_user_sdma_pkt_q *pq = req->pq;
+	struct sdma_mmu_node *node;
+	int ret;
+
+	node = kzalloc(sizeof(*node), GFP_KERNEL);
+	if (!node)
+		return -ENOMEM;
+
+	/* First kref "moves" to mmu_rb_handler */
+	kref_init(&node->rb.refcount);
+
+	/* "safety" kref to prevent release before add_system_iovec_to_sdma_packet() */
+	kref_get(&node->rb.refcount);
+
+	node->pq = pq;
+	ret = pin_system_pages(req, start, len, node, PFN_DOWN(len));
+	if (ret == 0) {
+		ret = hfi1_mmu_rb_insert(pq->handler, &node->rb);
+		if (ret)
+			free_system_node(node);
+		else
+			*node_p = node;
+
+		return ret;
+	}
+
+	kfree(node);
+	return ret;
+}
+
+static int get_system_cache_entry(struct user_sdma_request *req,
+				  struct sdma_mmu_node **node_p,
+				  size_t req_start, size_t req_len)
+{
+	struct hfi1_user_sdma_pkt_q *pq = req->pq;
+	u64 start = ALIGN_DOWN(req_start, PAGE_SIZE);
+	u64 end = PFN_ALIGN(req_start + req_len);
+	struct mmu_rb_handler *handler = pq->handler;
+	int ret;
+
+	if ((end - start) == 0) {
+		SDMA_DBG(req,
+			 "Request for empty cache entry req_start %lx req_len %lx start %llx end %llx",
+			 req_start, req_len, start, end);
+		return -EINVAL;
+	}
+
+	SDMA_DBG(req, "req_start %lx req_len %lu", req_start, req_len);
+
+	while (1) {
+		struct sdma_mmu_node *node =
+			find_system_node(handler, start, end);
+		u64 prepend_len = 0;
+
+		SDMA_DBG(req, "node %p start %llx end %llu", node, start, end);
+		if (!node) {
+			ret = add_system_pinning(req, node_p, start,
+						 end - start);
+			if (ret == -EEXIST) {
+				/*
+				 * Another execution context has inserted a
+				 * conficting entry first.
+				 */
+				continue;
+			}
+			return ret;
+		}
+
+		if (node->rb.addr <= start) {
+			/*
+			 * This entry covers at least part of the region. If it doesn't extend
+			 * to the end, then this will be called again for the next segment.
+			 */
+			*node_p = node;
+			return 0;
+		}
+
+		SDMA_DBG(req, "prepend: node->rb.addr %lx, node->rb.refcount %d",
+			 node->rb.addr, kref_read(&node->rb.refcount));
+		prepend_len = node->rb.addr - start;
+
+		/*
+		 * This node will not be returned, instead a new node
+		 * will be. So release the reference.
+		 */
+		kref_put(&node->rb.refcount, hfi1_mmu_rb_release);
+
+		/* Prepend a node to cover the beginning of the allocation */
+		ret = add_system_pinning(req, node_p, start, prepend_len);
+		if (ret == -EEXIST) {
+			/* Another execution context has inserted a conficting entry first. */
+			continue;
+		}
+		return ret;
+	}
+}
+
+static void sdma_mmu_rb_node_get(void *ctx)
+{
+	struct mmu_rb_node *node = ctx;
+
+	kref_get(&node->refcount);
+}
+
+static void sdma_mmu_rb_node_put(void *ctx)
+{
+	struct sdma_mmu_node *node = ctx;
+
+	kref_put(&node->rb.refcount, hfi1_mmu_rb_release);
+}
+
+static int add_mapping_to_sdma_packet(struct user_sdma_request *req,
+				      struct user_sdma_txreq *tx,
+				      struct sdma_mmu_node *cache_entry,
+				      size_t start,
+				      size_t from_this_cache_entry)
+{
+	struct hfi1_user_sdma_pkt_q *pq = req->pq;
+	unsigned int page_offset;
+	unsigned int from_this_page;
+	size_t page_index;
+	void *ctx;
+	int ret;
+
+	/*
+	 * Because the cache may be more fragmented than the memory that is being accessed,
+	 * it's not strictly necessary to have a descriptor per cache entry.
+	 */
+
+	while (from_this_cache_entry) {
+		page_index = PFN_DOWN(start - cache_entry->rb.addr);
+
+		if (page_index >= cache_entry->npages) {
+			SDMA_DBG(req,
+				 "Request for page_index %zu >= cache_entry->npages %u",
+				 page_index, cache_entry->npages);
+			return -EINVAL;
+		}
 
-	atomic_inc(&node->refcount);
+		page_offset = start - ALIGN_DOWN(start, PAGE_SIZE);
+		from_this_page = PAGE_SIZE - page_offset;
+
+		if (from_this_page < from_this_cache_entry) {
+			ctx = NULL;
+		} else {
+			/*
+			 * In the case they are equal the next line has no practical effect,
+			 * but it's better to do a register to register copy than a conditional
+			 * branch.
+			 */
+			from_this_page = from_this_cache_entry;
+			ctx = cache_entry;
+		}
+
+		ret = sdma_txadd_page(pq->dd, &tx->txreq,
+				      cache_entry->pages[page_index],
+				      page_offset, from_this_page,
+				      ctx,
+				      sdma_mmu_rb_node_get,
+				      sdma_mmu_rb_node_put);
+		if (ret) {
+			/*
+			 * When there's a failure, the entire request is freed by
+			 * user_sdma_send_pkts().
+			 */
+			SDMA_DBG(req,
+				 "sdma_txadd_page failed %d page_index %lu page_offset %u from_this_page %u",
+				 ret, page_index, page_offset, from_this_page);
+			return ret;
+		}
+		start += from_this_page;
+		from_this_cache_entry -= from_this_page;
+	}
 	return 0;
 }
 
+static int add_system_iovec_to_sdma_packet(struct user_sdma_request *req,
+					   struct user_sdma_txreq *tx,
+					   struct user_sdma_iovec *iovec,
+					   size_t from_this_iovec)
+{
+	while (from_this_iovec > 0) {
+		struct sdma_mmu_node *cache_entry;
+		size_t from_this_cache_entry;
+		size_t start;
+		int ret;
+
+		start = (uintptr_t)iovec->iov.iov_base + iovec->offset;
+		ret = get_system_cache_entry(req, &cache_entry, start,
+					     from_this_iovec);
+		if (ret) {
+			SDMA_DBG(req, "pin system segment failed %d", ret);
+			return ret;
+		}
+
+		from_this_cache_entry = cache_entry->rb.len - (start - cache_entry->rb.addr);
+		if (from_this_cache_entry > from_this_iovec)
+			from_this_cache_entry = from_this_iovec;
+
+		ret = add_mapping_to_sdma_packet(req, tx, cache_entry, start,
+						 from_this_cache_entry);
+
+		/*
+		 * Done adding cache_entry to zero or more sdma_desc. Can
+		 * kref_put() the "safety" kref taken under
+		 * get_system_cache_entry().
+		 */
+		kref_put(&cache_entry->rb.refcount, hfi1_mmu_rb_release);
+
+		if (ret) {
+			SDMA_DBG(req, "add system segment failed %d", ret);
+			return ret;
+		}
+
+		iovec->offset += from_this_cache_entry;
+		from_this_iovec -= from_this_cache_entry;
+	}
+
+	return 0;
+}
+
+static int add_system_pages_to_sdma_packet(struct user_sdma_request *req,
+					   struct user_sdma_txreq *tx,
+					   struct user_sdma_iovec *iovec,
+					   u32 *pkt_data_remaining)
+{
+	size_t remaining_to_add = *pkt_data_remaining;
+	/*
+	 * Walk through iovec entries, ensure the associated pages
+	 * are pinned and mapped, add data to the packet until no more
+	 * data remains to be added.
+	 */
+	while (remaining_to_add > 0) {
+		struct user_sdma_iovec *cur_iovec;
+		size_t from_this_iovec;
+		int ret;
+
+		cur_iovec = iovec;
+		from_this_iovec = iovec->iov.iov_len - iovec->offset;
+
+		if (from_this_iovec > remaining_to_add) {
+			from_this_iovec = remaining_to_add;
+		} else {
+			/* The current iovec entry will be consumed by this pass. */
+			req->iov_idx++;
+			iovec++;
+		}
+
+		ret = add_system_iovec_to_sdma_packet(req, tx, cur_iovec,
+						      from_this_iovec);
+		if (ret)
+			return ret;
+
+		remaining_to_add -= from_this_iovec;
+	}
+	*pkt_data_remaining = remaining_to_add;
+
+	return 0;
+}
+
+static bool sdma_rb_filter(struct mmu_rb_node *node, unsigned long addr,
+			   unsigned long len)
+{
+	return (bool)(node->addr == addr);
+}
+
 /*
  * Return 1 to remove the node from the rb tree and call the remove op.
  *
@@ -1476,10 +1634,6 @@
 		container_of(mnode, struct sdma_mmu_node, rb);
 	struct evict_data *evict_data = evict_arg;
 
-	/* is this node still being used? */
-	if (atomic_read(&node->refcount))
-		return 0; /* keep this node */
-
 	/* this node will be evicted, add its pages to our count */
 	evict_data->cleared += node->npages;
 
@@ -1495,16 +1649,5 @@
 	struct sdma_mmu_node *node =
 		container_of(mnode, struct sdma_mmu_node, rb);
 
-	unpin_sdma_pages(node);
-	kfree(node);
-}
-
-static int sdma_rb_invalidate(void *arg, struct mmu_rb_node *mnode)
-{
-	struct sdma_mmu_node *node =
-		container_of(mnode, struct sdma_mmu_node, rb);
-
-	if (!atomic_read(&node->refcount))
-		return 1;
-	return 0;
+	free_system_node(node);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/user_sdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/user_sdma.h
@@ -104,7 +104,6 @@
 struct sdma_mmu_node {
 	struct mmu_rb_node rb;
 	struct hfi1_user_sdma_pkt_q *pq;
-	atomic_t refcount;
 	struct page **pages;
 	unsigned int npages;
 };
@@ -112,16 +111,11 @@
 struct user_sdma_iovec {
 	struct list_head list;
 	struct iovec iov;
-	/* number of pages in this vector */
-	unsigned int npages;
-	/* array of pinned pages for this vector */
-	struct page **pages;
 	/*
 	 * offset into the virtual address space of the vector at
 	 * which we last left off.
 	 */
 	u64 offset;
-	struct sdma_mmu_node *node;
 };
 
 /* evict operation argument */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/verbs.c
@@ -778,8 +778,8 @@
 
 	/* add icrc, lt byte, and padding to flit */
 	if (extra_bytes)
-		ret = sdma_txadd_daddr(sde->dd, &tx->txreq,
-				       sde->dd->sdma_pad_phys, extra_bytes);
+		ret = sdma_txadd_daddr(sde->dd, &tx->txreq, sde->dd->sdma_pad_phys,
+				       extra_bytes);
 
 bail_txadd:
 	return ret;
@@ -1397,8 +1397,7 @@
 				      4096 : hfi1_max_mtu), IB_MTU_4096);
 	props->active_mtu = !valid_ib_mtu(ppd->ibmtu) ? props->max_mtu :
 		mtu_to_enum(ppd->ibmtu, IB_MTU_4096);
-	props->phys_mtu = HFI1_CAP_IS_KSET(AIP) ? hfi1_max_mtu :
-				ib_mtu_enum_to_int(props->max_mtu);
+	props->phys_mtu = hfi1_max_mtu;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hfi1/vnic_sdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hfi1/vnic_sdma.c
@@ -67,7 +67,8 @@
 				      &tx->txreq,
 				      skb_frag_page(frag),
 				      skb_frag_off(frag),
-				      skb_frag_size(frag));
+				      skb_frag_size(frag),
+				      NULL, NULL, NULL);
 		if (unlikely(ret))
 			goto bail_txadd;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_cq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_cq.c
@@ -125,7 +125,7 @@
 		goto err_out;
 	}
 
-	ret = xa_err(xa_store(&cq_table->array, hr_cq->cqn, hr_cq, GFP_KERNEL));
+	ret = xa_err(xa_store_irq(&cq_table->array, hr_cq->cqn, hr_cq, GFP_KERNEL));
 	if (ret) {
 		ibdev_err(ibdev, "failed to xa_store CQ, ret = %d.\n", ret);
 		goto err_put;
@@ -160,8 +160,7 @@
 	return 0;
 
 err_xa:
-	xa_erase(&cq_table->array, hr_cq->cqn);
-
+	xa_erase_irq(&cq_table->array, hr_cq->cqn);
 err_put:
 	hns_roce_table_put(hr_dev, &cq_table->table, hr_cq->cqn);
 
@@ -182,7 +181,7 @@
 		dev_err(dev, "DESTROY_CQ failed (%d) for CQN %06lx\n", ret,
 			hr_cq->cqn);
 
-	xa_erase(&cq_table->array, hr_cq->cqn);
+	xa_erase_irq(&cq_table->array, hr_cq->cqn);
 
 	/* Waiting interrupt process procedure carried out */
 	synchronize_irq(hr_dev->eq_table.eq[hr_cq->vector].irq);
@@ -478,13 +477,6 @@
 	struct ib_event event;
 	struct ib_cq *ibcq;
 
-	hr_cq = xa_load(&hr_dev->cq_table.array,
-			cqn & (hr_dev->caps.num_cqs - 1));
-	if (!hr_cq) {
-		dev_warn(dev, "Async event for bogus CQ 0x%06x\n", cqn);
-		return;
-	}
-
 	if (event_type != HNS_ROCE_EVENT_TYPE_CQ_ID_INVALID &&
 	    event_type != HNS_ROCE_EVENT_TYPE_CQ_ACCESS_ERROR &&
 	    event_type != HNS_ROCE_EVENT_TYPE_CQ_OVERFLOW) {
@@ -493,7 +485,16 @@
 		return;
 	}
 
-	refcount_inc(&hr_cq->refcount);
+	xa_lock(&hr_dev->cq_table.array);
+	hr_cq = xa_load(&hr_dev->cq_table.array,
+			cqn & (hr_dev->caps.num_cqs - 1));
+	if (hr_cq)
+		refcount_inc(&hr_cq->refcount);
+	xa_unlock(&hr_dev->cq_table.array);
+	if (!hr_cq) {
+		dev_warn(dev, "async event for bogus CQ 0x%06x\n", cqn);
+		return;
+	}
 
 	ibcq = &hr_cq->ib_cq;
 	if (ibcq->event_handler) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_device.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_device.h
@@ -100,6 +100,7 @@
 #define MR_TYPE_DMA				0x03
 
 #define HNS_ROCE_FRMR_MAX_PA			512
+#define HNS_ROCE_FRMR_ALIGN_SIZE		128
 
 #define PKEY_ID					0xffff
 #define GUID_LEN				8
@@ -121,6 +122,7 @@
 #define HNS_ROCE_CQ_BANK_NUM 4
 
 #define CQ_BANKID_SHIFT 2
+#define CQ_BANKID_MASK GENMASK(1, 0)
 
 /* The chip implementation of the consumer index is calculated
  * according to twice the actual EQ depth
@@ -219,6 +221,9 @@
 #define HNS_HW_PAGE_SHIFT			12
 #define HNS_HW_PAGE_SIZE			(1 << HNS_HW_PAGE_SHIFT)
 
+#define HNS_HW_MAX_PAGE_SHIFT			27
+#define HNS_HW_MAX_PAGE_SIZE			(1 << HNS_HW_MAX_PAGE_SHIFT)
+
 struct hns_roce_uar {
 	u64		pfn;
 	unsigned long	index;
@@ -559,6 +564,11 @@
 	u16			busy;
 };
 
+enum hns_roce_cmdq_state {
+	HNS_ROCE_CMDQ_STATE_NORMAL,
+	HNS_ROCE_CMDQ_STATE_FATAL_ERR,
+};
+
 struct hns_roce_cmdq {
 	struct dma_pool		*pool;
 	struct semaphore	poll_sem;
@@ -578,6 +588,7 @@
 	 * close device, switch into poll mode(non event mode)
 	 */
 	u8			use_events;
+	enum hns_roce_cmdq_state state;
 };
 
 struct hns_roce_cmd_mailbox {
@@ -753,7 +764,6 @@
 	u32		num_pi_qps;
 	u32		reserved_qps;
 	int		num_qpc_timer;
-	int		num_cqc_timer;
 	int		num_srqs;
 	u32		max_wqes;
 	u32		max_srq_wrs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_hem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_hem.c
@@ -597,11 +597,12 @@
 	}
 
 	/* Set HEM base address(128K/page, pa) to Hardware */
-	if (hr_dev->hw->set_hem(hr_dev, table, obj, HEM_HOP_STEP_DIRECT)) {
+	ret = hr_dev->hw->set_hem(hr_dev, table, obj, HEM_HOP_STEP_DIRECT);
+	if (ret) {
 		hns_roce_free_hem(hr_dev, table->hem[i]);
 		table->hem[i] = NULL;
-		ret = -ENODEV;
-		dev_err(dev, "set HEM base address to HW failed.\n");
+		dev_err(dev, "set HEM base address to HW failed, ret = %d.\n",
+			ret);
 		goto out;
 	}
 
@@ -976,6 +977,7 @@
 	size_t count; /* max ba numbers */
 	int start; /* start buf offset in this hem */
 	int end; /* end buf offset in this hem */
+	bool exist_bt;
 };
 
 /* All HEM items are linked in a tree structure */
@@ -987,7 +989,7 @@
 
 static struct hns_roce_hem_item *
 hem_list_alloc_item(struct hns_roce_dev *hr_dev, int start, int end, int count,
-		    bool exist_bt, int bt_level)
+		    bool exist_bt)
 {
 	struct hns_roce_hem_item *hem;
 
@@ -1004,6 +1006,7 @@
 		}
 	}
 
+	hem->exist_bt = exist_bt;
 	hem->count = count;
 	hem->start = start;
 	hem->end = end;
@@ -1014,22 +1017,22 @@
 }
 
 static void hem_list_free_item(struct hns_roce_dev *hr_dev,
-			       struct hns_roce_hem_item *hem, bool exist_bt)
+			       struct hns_roce_hem_item *hem)
 {
-	if (exist_bt)
+	if (hem->exist_bt)
 		dma_free_coherent(hr_dev->dev, hem->count * BA_BYTE_LEN,
 				  hem->addr, hem->dma_addr);
 	kfree(hem);
 }
 
 static void hem_list_free_all(struct hns_roce_dev *hr_dev,
-			      struct list_head *head, bool exist_bt)
+			      struct list_head *head)
 {
 	struct hns_roce_hem_item *hem, *temp_hem;
 
 	list_for_each_entry_safe(hem, temp_hem, head, list) {
 		list_del(&hem->list);
-		hem_list_free_item(hr_dev, hem, exist_bt);
+		hem_list_free_item(hr_dev, hem);
 	}
 }
 
@@ -1088,9 +1091,9 @@
  * @bt_level: base address table level
  * @unit: ba entries per bt page
  */
-static u32 hem_list_calc_ba_range(int hopnum, int bt_level, int unit)
+static u64 hem_list_calc_ba_range(int hopnum, int bt_level, int unit)
 {
-	u32 step;
+	u64 step;
 	int max;
 	int i;
 
@@ -1126,11 +1129,15 @@
 {
 	struct hns_roce_buf_region *r;
 	int total = 0;
-	int step;
+	u64 step;
 	int i;
 
 	for (i = 0; i < region_cnt; i++) {
 		r = (struct hns_roce_buf_region *)&regions[i];
+		/* when r->hopnum = 0, the region should not occupy root_ba. */
+		if (!r->hopnum)
+			continue;
+
 		if (r->hopnum > 1) {
 			step = hem_list_calc_ba_range(r->hopnum, 1, unit);
 			if (step > 0)
@@ -1157,7 +1164,7 @@
 	int ret = 0;
 	int max_ofs;
 	int level;
-	u32 step;
+	u64 step;
 	int end;
 
 	if (hopnum <= 1)
@@ -1181,10 +1188,12 @@
 
 	/* config L1 bt to last bt and link them to corresponding parent */
 	for (level = 1; level < hopnum; level++) {
-		cur = hem_list_search_item(&mid_bt[level], offset);
-		if (cur) {
-			hem_ptrs[level] = cur;
-			continue;
+		if (!hem_list_is_bottom_bt(hopnum, level)) {
+			cur = hem_list_search_item(&mid_bt[level], offset);
+			if (cur) {
+				hem_ptrs[level] = cur;
+				continue;
+			}
 		}
 
 		step = hem_list_calc_ba_range(hopnum, level, unit);
@@ -1194,9 +1203,9 @@
 		}
 
 		start_aligned = (distance / step) * step + r->offset;
-		end = min_t(int, start_aligned + step - 1, max_ofs);
+		end = min_t(u64, start_aligned + step - 1, max_ofs);
 		cur = hem_list_alloc_item(hr_dev, start_aligned, end, unit,
-					  true, level);
+					  true);
 		if (!cur) {
 			ret = -ENOMEM;
 			goto err_exit;
@@ -1223,7 +1232,7 @@
 
 err_exit:
 	for (level = 1; level < hopnum; level++)
-		hem_list_free_all(hr_dev, &temp_list[level], true);
+		hem_list_free_all(hr_dev, &temp_list[level]);
 
 	return ret;
 }
@@ -1248,7 +1257,7 @@
 	/* indicate to last region */
 	r = &regions[region_cnt - 1];
 	hem = hem_list_alloc_item(hr_dev, offset, r->offset + r->count - 1,
-				  ba_num, true, 0);
+				  ba_num, true);
 	if (!hem)
 		return ERR_PTR(-ENOMEM);
 
@@ -1264,16 +1273,26 @@
 {
 	struct hns_roce_hem_item *hem;
 
+	/* This is on the has_mtt branch, if r->hopnum
+	 * is 0, there is no root_ba to reuse for the
+	 * region's fake hem, so a dma_alloc request is
+	 * necessary here.
+	 */
 	hem = hem_list_alloc_item(hr_dev, r->offset, r->offset + r->count - 1,
-				  r->count, false, 0);
+				  r->count, !r->hopnum);
 	if (!hem)
 		return -ENOMEM;
 
-	hem_list_assign_bt(hr_dev, hem, cpu_base, phy_base);
+	/* The root_ba can be reused only when r->hopnum > 0. */
+	if (r->hopnum)
+		hem_list_assign_bt(hr_dev, hem, cpu_base, phy_base);
 	list_add(&hem->list, branch_head);
 	list_add(&hem->sibling, leaf_head);
 
-	return r->count;
+	/* If r->hopnum == 0, 0 is returned,
+	 * so that the root_bt entry is not occupied.
+	 */
+	return r->hopnum ? r->count : 0;
 }
 
 static int setup_middle_bt(struct hns_roce_dev *hr_dev, void *cpu_base,
@@ -1283,7 +1302,7 @@
 	struct hns_roce_hem_item *hem, *temp_hem;
 	int total = 0;
 	int offset;
-	int step;
+	u64 step;
 
 	step = hem_list_calc_ba_range(r->hopnum, 1, unit);
 	if (step < 1)
@@ -1317,7 +1336,7 @@
 		return -ENOMEM;
 
 	total = 0;
-	for (i = 0; i < region_cnt && total < max_ba_num; i++) {
+	for (i = 0; i < region_cnt && total <= max_ba_num; i++) {
 		r = &regions[i];
 		if (!r->count)
 			continue;
@@ -1383,14 +1402,19 @@
 			     region_cnt);
 	if (ret) {
 		for (i = 0; i < region_cnt; i++)
-			hem_list_free_all(hr_dev, &head.branch[i], false);
+			hem_list_free_all(hr_dev, &head.branch[i]);
 
-		hem_list_free_all(hr_dev, &head.root, true);
+		hem_list_free_all(hr_dev, &head.root);
 	}
 
 	return ret;
 }
 
+/* This is the bottom bt pages number of a 100G MR on 4K OS, assuming
+ * the bt page size is not expanded by cal_best_bt_pg_sz()
+ */
+#define RESCHED_LOOP_CNT_THRESHOLD_ON_4K 12800
+
 /* construct the base address table and link them by address hop config */
 int hns_roce_hem_list_request(struct hns_roce_dev *hr_dev,
 			      struct hns_roce_hem_list *hem_list,
@@ -1399,6 +1423,7 @@
 {
 	const struct hns_roce_buf_region *r;
 	int ofs, end;
+	int loop;
 	int unit;
 	int ret;
 	int i;
@@ -1416,7 +1441,10 @@
 			continue;
 
 		end = r->offset + r->count;
-		for (ofs = r->offset; ofs < end; ofs += unit) {
+		for (ofs = r->offset, loop = 1; ofs < end; ofs += unit, loop++) {
+			if (!(loop % RESCHED_LOOP_CNT_THRESHOLD_ON_4K))
+				cond_resched();
+
 			ret = hem_list_alloc_mid_bt(hr_dev, r, unit, ofs,
 						    hem_list->mid_bt[i],
 						    &hem_list->btm_bt);
@@ -1448,10 +1476,9 @@
 
 	for (i = 0; i < HNS_ROCE_MAX_BT_REGION; i++)
 		for (j = 0; j < HNS_ROCE_MAX_BT_LEVEL; j++)
-			hem_list_free_all(hr_dev, &hem_list->mid_bt[i][j],
-					  j != 0);
+			hem_list_free_all(hr_dev, &hem_list->mid_bt[i][j]);
 
-	hem_list_free_all(hr_dev, &hem_list->root_bt, true);
+	hem_list_free_all(hr_dev, &hem_list->root_bt);
 	INIT_LIST_HEAD(&hem_list->btm_bt);
 	hem_list->root_ba = 0;
 }
@@ -1469,19 +1496,22 @@
 
 void *hns_roce_hem_list_find_mtt(struct hns_roce_dev *hr_dev,
 				 struct hns_roce_hem_list *hem_list,
-				 int offset, int *mtt_cnt, u64 *phy_addr)
+				 int offset, int *mtt_cnt)
 {
 	struct list_head *head = &hem_list->btm_bt;
 	struct hns_roce_hem_item *hem, *temp_hem;
 	void *cpu_base = NULL;
-	u64 phy_base = 0;
+	int loop = 1;
 	int nr = 0;
 
 	list_for_each_entry_safe(hem, temp_hem, head, sibling) {
+		if (!(loop % RESCHED_LOOP_CNT_THRESHOLD_ON_4K))
+			cond_resched();
+		loop++;
+
 		if (hem_list_page_is_in_range(hem, offset)) {
 			nr = offset - hem->start;
 			cpu_base = hem->addr + nr * BA_BYTE_LEN;
-			phy_base = hem->dma_addr + nr * BA_BYTE_LEN;
 			nr = hem->end + 1 - offset;
 			break;
 		}
@@ -1490,8 +1520,5 @@
 	if (mtt_cnt)
 		*mtt_cnt = nr;
 
-	if (phy_addr)
-		*phy_addr = phy_base;
-
 	return cpu_base;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_hem.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_hem.h
@@ -61,16 +61,16 @@
 	 (sizeof(struct scatterlist) + sizeof(void *)))
 
 #define check_whether_bt_num_3(type, hop_num) \
-	(type < HEM_TYPE_MTT && hop_num == 2)
+	((type) < HEM_TYPE_MTT && (hop_num) == 2)
 
 #define check_whether_bt_num_2(type, hop_num) \
-	((type < HEM_TYPE_MTT && hop_num == 1) || \
-	(type >= HEM_TYPE_MTT && hop_num == 2))
+	(((type) < HEM_TYPE_MTT && (hop_num) == 1) || \
+	((type) >= HEM_TYPE_MTT && (hop_num) == 2))
 
 #define check_whether_bt_num_1(type, hop_num) \
-	((type < HEM_TYPE_MTT && hop_num == HNS_ROCE_HOP_NUM_0) || \
-	(type >= HEM_TYPE_MTT && hop_num == 1) || \
-	(type >= HEM_TYPE_MTT && hop_num == HNS_ROCE_HOP_NUM_0))
+	(((type) < HEM_TYPE_MTT && (hop_num) == HNS_ROCE_HOP_NUM_0) || \
+	((type) >= HEM_TYPE_MTT && (hop_num) == 1) || \
+	((type) >= HEM_TYPE_MTT && (hop_num) == HNS_ROCE_HOP_NUM_0))
 
 struct hns_roce_hem_chunk {
 	struct list_head	 list;
@@ -132,7 +132,7 @@
 			       struct hns_roce_hem_list *hem_list);
 void *hns_roce_hem_list_find_mtt(struct hns_roce_dev *hr_dev,
 				 struct hns_roce_hem_list *hem_list,
-				 int offset, int *mtt_cnt, u64 *phy_addr);
+				 int offset, int *mtt_cnt);
 
 static inline void hns_roce_hem_first(struct hns_roce_hem *hem,
 				      struct hns_roce_hem_iter *iter)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_hw_v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_hw_v2.c
@@ -33,6 +33,7 @@
 #include <linux/acpi.h>
 #include <linux/etherdevice.h>
 #include <linux/interrupt.h>
+#include <linux/iopoll.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <net/addrconf.h>
@@ -81,7 +82,6 @@
 	HR_OPC_MAP(ATOMIC_CMP_AND_SWP,		ATOM_CMP_AND_SWAP),
 	HR_OPC_MAP(ATOMIC_FETCH_AND_ADD,	ATOM_FETCH_AND_ADD),
 	HR_OPC_MAP(SEND_WITH_INV,		SEND_WITH_INV),
-	HR_OPC_MAP(LOCAL_INV,			LOCAL_INV),
 	HR_OPC_MAP(MASKED_ATOMIC_CMP_AND_SWP,	ATOM_MSK_CMP_AND_SWAP),
 	HR_OPC_MAP(MASKED_ATOMIC_FETCH_AND_ADD,	ATOM_MSK_FETCH_AND_ADD),
 	HR_OPC_MAP(REG_MR,			FAST_REG_PMR),
@@ -148,8 +148,15 @@
 		aseg->cmp_data = 0;
 	}
 
-	roce_set_field(rc_sq_wqe->byte_16, V2_RC_SEND_WQE_BYTE_16_SGE_NUM_M,
-		       V2_RC_SEND_WQE_BYTE_16_SGE_NUM_S, valid_num_sge);
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_SGE_NUM, valid_num_sge);
+}
+
+static unsigned int get_std_sge_num(struct hns_roce_qp *qp)
+{
+	if (qp->ibqp.qp_type == IB_QPT_GSI || qp->ibqp.qp_type == IB_QPT_UD)
+		return 0;
+
+	return HNS_ROCE_SGE_IN_WQE;
 }
 
 static int fill_ext_sge_inl_data(struct hns_roce_qp *qp,
@@ -157,16 +164,16 @@
 				 unsigned int *sge_idx, u32 msg_len)
 {
 	struct ib_device *ibdev = &(to_hr_dev(qp->ibqp.device))->ib_dev;
-	unsigned int dseg_len = sizeof(struct hns_roce_v2_wqe_data_seg);
-	unsigned int ext_sge_sz = qp->sq.max_gs * dseg_len;
 	unsigned int left_len_in_pg;
 	unsigned int idx = *sge_idx;
+	unsigned int std_sge_num;
 	unsigned int i = 0;
 	unsigned int len;
 	void *addr;
 	void *dseg;
 
-	if (msg_len > ext_sge_sz) {
+	std_sge_num = get_std_sge_num(qp);
+	if (msg_len > (qp->sq.max_gs - std_sge_num) * HNS_ROCE_SGE_SIZE) {
 		ibdev_err(ibdev,
 			  "no enough extended sge space for inline data.\n");
 		return -EINVAL;
@@ -186,7 +193,7 @@
 		if (len <= left_len_in_pg) {
 			memcpy(dseg, addr, len);
 
-			idx += len / dseg_len;
+			idx += len / HNS_ROCE_SGE_SIZE;
 
 			i++;
 			if (i >= wr->num_sge)
@@ -201,7 +208,7 @@
 
 			len -= left_len_in_pg;
 			addr += left_len_in_pg;
-			idx += left_len_in_pg / dseg_len;
+			idx += left_len_in_pg / HNS_ROCE_SGE_SIZE;
 			dseg = hns_roce_get_extend_sge(qp,
 						idx & (qp->sge.sge_cnt - 1));
 			left_len_in_pg = 1 << HNS_HW_PAGE_SHIFT;
@@ -237,7 +244,7 @@
 	struct hns_roce_dev *hr_dev = to_hr_dev(qp->ibqp.device);
 	int mtu = ib_mtu_enum_to_int(qp->path_mtu);
 
-	if (len > qp->max_inline_data || len > mtu) {
+	if (mtu < 0 || len > qp->max_inline_data || len > mtu) {
 		ibdev_err(&hr_dev->ib_dev,
 			  "invalid length of data, data len = %u, max inline len = %u, path mtu = %d.\n",
 			  len, qp->max_inline_data, mtu);
@@ -270,8 +277,7 @@
 	dseg += sizeof(struct hns_roce_v2_rc_send_wqe);
 
 	if (msg_len <= HNS_ROCE_V2_MAX_RC_INL_INN_SZ) {
-		roce_set_bit(rc_sq_wqe->byte_20,
-			     V2_RC_SEND_WQE_BYTE_20_INL_TYPE_S, 0);
+		hr_reg_clear(rc_sq_wqe, RC_SEND_WQE_INL_TYPE);
 
 		for (i = 0; i < wr->num_sge; i++) {
 			memcpy(dseg, ((void *)wr->sg_list[i].addr),
@@ -279,17 +285,13 @@
 			dseg += wr->sg_list[i].length;
 		}
 	} else {
-		roce_set_bit(rc_sq_wqe->byte_20,
-			     V2_RC_SEND_WQE_BYTE_20_INL_TYPE_S, 1);
+		hr_reg_enable(rc_sq_wqe, RC_SEND_WQE_INL_TYPE);
 
 		ret = fill_ext_sge_inl_data(qp, wr, &curr_idx, msg_len);
 		if (ret)
 			return ret;
 
-		roce_set_field(rc_sq_wqe->byte_16,
-			       V2_RC_SEND_WQE_BYTE_16_SGE_NUM_M,
-			       V2_RC_SEND_WQE_BYTE_16_SGE_NUM_S,
-			       curr_idx - *sge_idx);
+		hr_reg_write(rc_sq_wqe, RC_SEND_WQE_SGE_NUM, curr_idx - *sge_idx);
 	}
 
 	*sge_idx = curr_idx;
@@ -308,12 +310,10 @@
 	int j = 0;
 	int i;
 
-	roce_set_field(rc_sq_wqe->byte_20,
-		       V2_RC_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_M,
-		       V2_RC_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_S,
-		       (*sge_ind) & (qp->sge.sge_cnt - 1));
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_MSG_START_SGE_IDX,
+		     (*sge_ind) & (qp->sge.sge_cnt - 1));
 
-	roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_INLINE_S,
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_INLINE,
 		     !!(wr->send_flags & IB_SEND_INLINE));
 	if (wr->send_flags & IB_SEND_INLINE)
 		return set_rc_inl(qp, wr, rc_sq_wqe, sge_ind);
@@ -338,9 +338,7 @@
 			       valid_num_sge - HNS_ROCE_SGE_IN_WQE);
 	}
 
-	roce_set_field(rc_sq_wqe->byte_16,
-		       V2_RC_SEND_WQE_BYTE_16_SGE_NUM_M,
-		       V2_RC_SEND_WQE_BYTE_16_SGE_NUM_S, valid_num_sge);
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_SGE_NUM, valid_num_sge);
 
 	return 0;
 }
@@ -411,8 +409,7 @@
 
 	ud_sq_wqe->immtdata = get_immtdata(wr);
 
-	roce_set_field(ud_sq_wqe->byte_4, V2_UD_SEND_WQE_BYTE_4_OPCODE_M,
-		       V2_UD_SEND_WQE_BYTE_4_OPCODE_S, to_hr_opcode(ib_op));
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_OPCODE, to_hr_opcode(ib_op));
 
 	return 0;
 }
@@ -423,21 +420,15 @@
 	struct ib_device *ib_dev = ah->ibah.device;
 	struct hns_roce_dev *hr_dev = to_hr_dev(ib_dev);
 
-	roce_set_field(ud_sq_wqe->byte_24, V2_UD_SEND_WQE_BYTE_24_UDPSPN_M,
-		       V2_UD_SEND_WQE_BYTE_24_UDPSPN_S, ah->av.udp_sport);
-
-	roce_set_field(ud_sq_wqe->byte_36, V2_UD_SEND_WQE_BYTE_36_HOPLIMIT_M,
-		       V2_UD_SEND_WQE_BYTE_36_HOPLIMIT_S, ah->av.hop_limit);
-	roce_set_field(ud_sq_wqe->byte_36, V2_UD_SEND_WQE_BYTE_36_TCLASS_M,
-		       V2_UD_SEND_WQE_BYTE_36_TCLASS_S, ah->av.tclass);
-	roce_set_field(ud_sq_wqe->byte_40, V2_UD_SEND_WQE_BYTE_40_FLOW_LABEL_M,
-		       V2_UD_SEND_WQE_BYTE_40_FLOW_LABEL_S, ah->av.flowlabel);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_UDPSPN, ah->av.udp_sport);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_HOPLIMIT, ah->av.hop_limit);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_TCLASS, ah->av.tclass);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_FLOW_LABEL, ah->av.flowlabel);
 
 	if (WARN_ON(ah->av.sl > MAX_SERVICE_LEVEL))
 		return -EINVAL;
 
-	roce_set_field(ud_sq_wqe->byte_40, V2_UD_SEND_WQE_BYTE_40_SL_M,
-		       V2_UD_SEND_WQE_BYTE_40_SL_S, ah->av.sl);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_SL, ah->av.sl);
 
 	ud_sq_wqe->sgid_index = ah->av.gid_index;
 
@@ -447,10 +438,8 @@
 	if (hr_dev->pci_dev->revision >= PCI_REVISION_ID_HIP09)
 		return 0;
 
-	roce_set_bit(ud_sq_wqe->byte_40, V2_UD_SEND_WQE_BYTE_40_UD_VLAN_EN_S,
-		     ah->av.vlan_en);
-	roce_set_field(ud_sq_wqe->byte_36, V2_UD_SEND_WQE_BYTE_36_VLAN_M,
-		       V2_UD_SEND_WQE_BYTE_36_VLAN_S, ah->av.vlan_id);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_VLAN_EN, ah->av.vlan_en);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_VLAN, ah->av.vlan_id);
 
 	return 0;
 }
@@ -470,32 +459,24 @@
 	valid_num_sge = calc_wr_sge_num(wr, &msg_len);
 
 	ret = set_ud_opcode(ud_sq_wqe, wr);
-	if (WARN_ON(ret))
+	if (WARN_ON_ONCE(ret))
 		return ret;
 
 	ud_sq_wqe->msg_len = cpu_to_le32(msg_len);
 
-	roce_set_bit(ud_sq_wqe->byte_4, V2_UD_SEND_WQE_BYTE_4_CQE_S,
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_CQE,
 		     !!(wr->send_flags & IB_SEND_SIGNALED));
-
-	roce_set_bit(ud_sq_wqe->byte_4, V2_UD_SEND_WQE_BYTE_4_SE_S,
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_SE,
 		     !!(wr->send_flags & IB_SEND_SOLICITED));
 
-	roce_set_field(ud_sq_wqe->byte_16, V2_UD_SEND_WQE_BYTE_16_PD_M,
-		       V2_UD_SEND_WQE_BYTE_16_PD_S, to_hr_pd(qp->ibqp.pd)->pdn);
-
-	roce_set_field(ud_sq_wqe->byte_16, V2_UD_SEND_WQE_BYTE_16_SGE_NUM_M,
-		       V2_UD_SEND_WQE_BYTE_16_SGE_NUM_S, valid_num_sge);
-
-	roce_set_field(ud_sq_wqe->byte_20,
-		       V2_UD_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_M,
-		       V2_UD_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_S,
-		       curr_idx & (qp->sge.sge_cnt - 1));
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_PD, to_hr_pd(qp->ibqp.pd)->pdn);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_SGE_NUM, valid_num_sge);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_MSG_START_SGE_IDX,
+		     curr_idx & (qp->sge.sge_cnt - 1));
 
 	ud_sq_wqe->qkey = cpu_to_le32(ud_wr(wr)->remote_qkey & 0x80000000 ?
 			  qp->qkey : ud_wr(wr)->remote_qkey);
-	roce_set_field(ud_sq_wqe->byte_32, V2_UD_SEND_WQE_BYTE_32_DQPN_M,
-		       V2_UD_SEND_WQE_BYTE_32_DQPN_S, ud_wr(wr)->remote_qpn);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_DQPN, ud_wr(wr)->remote_qpn);
 
 	ret = fill_ud_av(ud_sq_wqe, ah);
 	if (ret)
@@ -515,8 +496,7 @@
 		dma_wmb();
 
 	*sge_idx = curr_idx;
-	roce_set_bit(ud_sq_wqe->byte_4, V2_UD_SEND_WQE_BYTE_4_OWNER_S,
-		     owner_bit);
+	hr_reg_write(ud_sq_wqe, UD_SEND_WQE_OWNER, owner_bit);
 
 	return 0;
 }
@@ -551,9 +531,6 @@
 		else
 			ret = -EOPNOTSUPP;
 		break;
-	case IB_WR_LOCAL_INV:
-		roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_SO_S, 1);
-		fallthrough;
 	case IB_WR_SEND_WITH_INV:
 		rc_sq_wqe->inv_key = cpu_to_le32(wr->ex.invalidate_rkey);
 		break;
@@ -564,11 +541,11 @@
 	if (unlikely(ret))
 		return ret;
 
-	roce_set_field(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_OPCODE_M,
-		       V2_RC_SEND_WQE_BYTE_4_OPCODE_S, to_hr_opcode(ib_op));
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_OPCODE, to_hr_opcode(ib_op));
 
 	return ret;
 }
+
 static inline int set_rc_wqe(struct hns_roce_qp *qp,
 			     const struct ib_send_wr *wr,
 			     void *wqe, unsigned int *sge_idx,
@@ -586,16 +563,16 @@
 	rc_sq_wqe->msg_len = cpu_to_le32(msg_len);
 
 	ret = set_rc_opcode(hr_dev, rc_sq_wqe, wr);
-	if (WARN_ON(ret))
+	if (WARN_ON_ONCE(ret))
 		return ret;
 
-	roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_FENCE_S,
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_SO,
 		     (wr->send_flags & IB_SEND_FENCE) ? 1 : 0);
 
-	roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_SE_S,
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_SE,
 		     (wr->send_flags & IB_SEND_SOLICITED) ? 1 : 0);
 
-	roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_CQE_S,
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_CQE,
 		     (wr->send_flags & IB_SEND_SIGNALED) ? 1 : 0);
 
 	if (wr->opcode == IB_WR_ATOMIC_CMP_AND_SWP ||
@@ -615,8 +592,7 @@
 		dma_wmb();
 
 	*sge_idx = curr_idx;
-	roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_OWNER_S,
-		     owner_bit);
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_OWNER, owner_bit);
 
 	return ret;
 }
@@ -677,16 +653,19 @@
 static void write_dwqe(struct hns_roce_dev *hr_dev, struct hns_roce_qp *qp,
 		       void *wqe)
 {
+#define HNS_ROCE_SL_SHIFT 2
 	struct hns_roce_v2_rc_send_wqe *rc_sq_wqe = wqe;
 
+	if (unlikely(qp->state == IB_QPS_ERR)) {
+		flush_cqe(hr_dev, qp);
+		return;
+	}
 	/* All kinds of DirectWQE have the same header field layout */
-	roce_set_bit(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_FLAG_S, 1);
-	roce_set_field(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_DB_SL_L_M,
-		       V2_RC_SEND_WQE_BYTE_4_DB_SL_L_S, qp->sl);
-	roce_set_field(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_DB_SL_H_M,
-		       V2_RC_SEND_WQE_BYTE_4_DB_SL_H_S, qp->sl >> 2);
-	roce_set_field(rc_sq_wqe->byte_4, V2_RC_SEND_WQE_BYTE_4_WQE_INDEX_M,
-		       V2_RC_SEND_WQE_BYTE_4_WQE_INDEX_S, qp->sq.head);
+	hr_reg_enable(rc_sq_wqe, RC_SEND_WQE_FLAG);
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_DB_SL_L, qp->sl);
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_DB_SL_H,
+		     qp->sl >> HNS_ROCE_SL_SHIFT);
+	hr_reg_write(rc_sq_wqe, RC_SEND_WQE_WQE_INDEX, qp->sq.head);
 
 	hns_roce_write512(hr_dev, wqe, qp->sq.db_reg);
 }
@@ -756,7 +735,8 @@
 		qp->sq.head += nreq;
 		qp->next_sge = sge_idx;
 
-		if (nreq == 1 && (qp->en_flags & HNS_ROCE_QP_CAP_DIRECT_WQE))
+		if (nreq == 1 && !ret &&
+		    (qp->en_flags & HNS_ROCE_QP_CAP_DIRECT_WQE))
 			write_dwqe(hr_dev, qp, wqe);
 		else
 			update_sq_db(hr_dev, qp);
@@ -1050,9 +1030,14 @@
 					unsigned long instance_stage,
 					unsigned long reset_stage)
 {
+#define HW_RESET_TIMEOUT_US 1000000
+#define HW_RESET_SLEEP_US 1000
+
 	struct hns_roce_v2_priv *priv = hr_dev->priv;
 	struct hnae3_handle *handle = priv->handle;
 	const struct hnae3_ae_ops *ops = handle->ae_algo->ops;
+	unsigned long val;
+	int ret;
 
 	/* When hardware reset is detected, we should stop sending mailbox&cmq&
 	 * doorbell to hardware. If now in .init_instance() function, we should
@@ -1064,7 +1049,11 @@
 	 * again.
 	 */
 	hr_dev->dis_db = true;
-	if (!ops->get_hw_reset_stat(handle))
+
+	ret = read_poll_timeout(ops->ae_dev_reset_cnt, val,
+				val > hr_dev->reset_cnt, HW_RESET_SLEEP_US,
+				HW_RESET_TIMEOUT_US, false, handle);
+	if (!ret)
 		hr_dev->is_reset = true;
 
 	if (!hr_dev->is_reset || reset_stage == HNS_ROCE_STATE_RST_INIT ||
@@ -1263,6 +1252,40 @@
 	return tail == priv->cmq.csq.head;
 }
 
+static void update_cmdq_status(struct hns_roce_dev *hr_dev)
+{
+	struct hns_roce_v2_priv *priv = hr_dev->priv;
+	struct hnae3_handle *handle = priv->handle;
+
+	if (handle->rinfo.reset_state == HNS_ROCE_STATE_RST_INIT ||
+	    handle->rinfo.instance_state == HNS_ROCE_STATE_INIT)
+		hr_dev->cmd.state = HNS_ROCE_CMDQ_STATE_FATAL_ERR;
+}
+
+static int hns_roce_cmd_err_convert_errno(u16 desc_ret)
+{
+	struct hns_roce_cmd_errcode errcode_table[] = {
+		{CMD_EXEC_SUCCESS, 0},
+		{CMD_NO_AUTH, -EPERM},
+		{CMD_NOT_EXIST, -EOPNOTSUPP},
+		{CMD_CRQ_FULL, -EXFULL},
+		{CMD_NEXT_ERR, -ENOSR},
+		{CMD_NOT_EXEC, -ENOTBLK},
+		{CMD_PARA_ERR, -EINVAL},
+		{CMD_RESULT_ERR, -ERANGE},
+		{CMD_TIMEOUT, -ETIME},
+		{CMD_HILINK_ERR, -ENOLINK},
+		{CMD_INFO_ILLEGAL, -ENXIO},
+		{CMD_INVALID, -EBADR},
+	};
+	u16 i;
+
+	for (i = 0; i < ARRAY_SIZE(errcode_table); i++)
+		if (desc_ret == errcode_table[i].return_status)
+			return errcode_table[i].errno;
+	return -EIO;
+}
+
 static int __hns_roce_cmq_send(struct hns_roce_dev *hr_dev,
 			       struct hns_roce_cmq_desc *desc, int num)
 {
@@ -1307,7 +1330,7 @@
 			dev_err_ratelimited(hr_dev->dev,
 					    "Cmdq IO error, opcode = %x, return = %x\n",
 					    desc->opcode, desc_ret);
-			ret = -EIO;
+			ret = hns_roce_cmd_err_convert_errno(desc_ret);
 		}
 	} else {
 		/* FW/HW reset or incorrect number of desc */
@@ -1316,6 +1339,8 @@
 			 csq->head, tail);
 		csq->head = tail;
 
+		update_cmdq_status(hr_dev);
+
 		ret = -EAGAIN;
 	}
 
@@ -1330,6 +1355,9 @@
 	bool busy;
 	int ret;
 
+	if (hr_dev->cmd.state == HNS_ROCE_CMDQ_STATE_FATAL_ERR)
+		return -EIO;
+
 	if (!v2_chk_mbox_is_avail(hr_dev, &busy))
 		return busy ? -EBUSY : 0;
 
@@ -1526,6 +1554,9 @@
 {
 	int i;
 
+	if (hr_dev->cmd.state == HNS_ROCE_CMDQ_STATE_FATAL_ERR)
+		return;
+
 	for (i = hr_dev->func_num - 1; i >= 0; i--) {
 		__hns_roce_function_clear(hr_dev, i);
 		if (i != 0)
@@ -1594,11 +1625,17 @@
 {
 	struct hns_roce_cmq_desc desc;
 	struct hns_roce_cmq_req *req = (struct hns_roce_cmq_req *)desc.data;
+	u32 clock_cycles_of_1us;
 
 	hns_roce_cmq_setup_basic_desc(&desc, HNS_ROCE_OPC_CFG_GLOBAL_PARAM,
 				      false);
 
-	hr_reg_write(req, CFG_GLOBAL_PARAM_1US_CYCLES, 0x3e8);
+	if (hr_dev->pci_dev->revision == PCI_REVISION_ID_HIP08)
+		clock_cycles_of_1us = HNS_ROCE_1NS_CFG;
+	else
+		clock_cycles_of_1us = HNS_ROCE_1US_CFG;
+
+	hr_reg_write(req, CFG_GLOBAL_PARAM_1US_CYCLES, clock_cycles_of_1us);
 	hr_reg_write(req, CFG_GLOBAL_PARAM_UDP_PORT, ROCE_V2_UDP_DPORT);
 
 	return hns_roce_cmq_send(hr_dev, &desc, 1);
@@ -1749,17 +1786,16 @@
 	swt = (struct hns_roce_vf_switch *)desc.data;
 	hns_roce_cmq_setup_basic_desc(&desc, HNS_SWITCH_PARAMETER_CFG, true);
 	swt->rocee_sel |= cpu_to_le32(HNS_ICL_SWITCH_CMD_ROCEE_SEL);
-	roce_set_field(swt->fun_id, VF_SWITCH_DATA_FUN_ID_VF_ID_M,
-		       VF_SWITCH_DATA_FUN_ID_VF_ID_S, vf_id);
+	hr_reg_write(swt, VF_SWITCH_VF_ID, vf_id);
 	ret = hns_roce_cmq_send(hr_dev, &desc, 1);
 	if (ret)
 		return ret;
 
 	desc.flag = cpu_to_le16(HNS_ROCE_CMD_FLAG_IN);
 	desc.flag &= cpu_to_le16(~HNS_ROCE_CMD_FLAG_WR);
-	roce_set_bit(swt->cfg, VF_SWITCH_DATA_CFG_ALW_LPBK_S, 1);
-	roce_set_bit(swt->cfg, VF_SWITCH_DATA_CFG_ALW_LCL_LPBK_S, 0);
-	roce_set_bit(swt->cfg, VF_SWITCH_DATA_CFG_ALW_DST_OVRD_S, 1);
+	hr_reg_enable(swt, VF_SWITCH_ALW_LPBK);
+	hr_reg_clear(swt, VF_SWITCH_ALW_LCL_LPBK);
+	hr_reg_enable(swt, VF_SWITCH_ALW_DST_OVRD);
 
 	return hns_roce_cmq_send(hr_dev, &desc, 1);
 }
@@ -1939,7 +1975,7 @@
 	caps->num_mtpts		= HNS_ROCE_V2_MAX_MTPT_NUM;
 	caps->num_pds		= HNS_ROCE_V2_MAX_PD_NUM;
 	caps->num_qpc_timer	= HNS_ROCE_V2_MAX_QPC_TIMER_NUM;
-	caps->num_cqc_timer	= HNS_ROCE_V2_MAX_CQC_TIMER_NUM;
+	caps->cqc_timer_bt_num	= HNS_ROCE_V2_MAX_CQC_TIMER_BT_NUM;
 
 	caps->max_qp_init_rdma	= HNS_ROCE_V2_MAX_QP_INIT_RDMA;
 	caps->max_qp_dest_rdma	= HNS_ROCE_V2_MAX_QP_DEST_RDMA;
@@ -2170,7 +2206,7 @@
 		caps->gid_table_len[0] = caps->gmv_bt_num *
 					(HNS_HW_PAGE_SIZE / caps->gmv_entry_sz);
 
-		caps->gmv_entry_num = caps->gmv_bt_num * (PAGE_SIZE /
+		caps->gmv_entry_num = caps->gmv_bt_num * (HNS_HW_PAGE_SIZE /
 							  caps->gmv_entry_sz);
 	} else {
 		u32 func_num = max_t(u32, 1, hr_dev->func_num);
@@ -2233,7 +2269,6 @@
 	caps->max_rq_sg = roundup_pow_of_two(caps->max_rq_sg);
 	caps->max_extend_sg	     = le32_to_cpu(resp_a->max_extend_sg);
 	caps->num_qpc_timer	     = le16_to_cpu(resp_a->num_qpc_timer);
-	caps->num_cqc_timer	     = le16_to_cpu(resp_a->num_cqc_timer);
 	caps->max_srq_sges	     = le16_to_cpu(resp_a->max_srq_sges);
 	caps->max_srq_sges = roundup_pow_of_two(caps->max_srq_sges);
 	caps->num_aeq_vectors	     = resp_a->num_aeq_vectors;
@@ -2365,6 +2400,9 @@
 					  V2_QUERY_PF_CAPS_D_RQWQE_HOP_NUM_M,
 					  V2_QUERY_PF_CAPS_D_RQWQE_HOP_NUM_S);
 
+	if (!(caps->page_size_cap & PAGE_SIZE))
+		caps->page_size_cap = HNS_ROCE_V2_PAGE_SIZE_SUPPORTED;
+
 	return 0;
 }
 
@@ -2564,14 +2602,16 @@
 static struct hns_roce_link_table *
 alloc_link_table_buf(struct hns_roce_dev *hr_dev)
 {
+	u16 total_sl = hr_dev->caps.sl_num * hr_dev->func_num;
 	struct hns_roce_v2_priv *priv = hr_dev->priv;
 	struct hns_roce_link_table *link_tbl;
 	u32 pg_shift, size, min_size;
 
 	link_tbl = &priv->ext_llm;
 	pg_shift = hr_dev->caps.llm_buf_pg_sz + PAGE_SHIFT;
-	size = hr_dev->caps.num_qps * HNS_ROCE_V2_EXT_LLM_ENTRY_SZ;
-	min_size = HNS_ROCE_EXT_LLM_MIN_PAGES(hr_dev->caps.sl_num) << pg_shift;
+	size = hr_dev->caps.num_qps * hr_dev->func_num *
+	       HNS_ROCE_V2_EXT_LLM_ENTRY_SZ;
+	min_size = HNS_ROCE_EXT_LLM_MIN_PAGES(total_sl) << pg_shift;
 
 	/* Alloc data table */
 	size = max(size, min_size);
@@ -2802,6 +2842,9 @@
 	mb_st = (struct hns_roce_mbox_status *)desc.data;
 	end = msecs_to_jiffies(timeout) + jiffies;
 	while (v2_chk_mbox_is_avail(hr_dev, &busy)) {
+		if (hr_dev->cmd.state == HNS_ROCE_CMDQ_STATE_FATAL_ERR)
+			return -EIO;
+
 		status = 0;
 		hns_roce_cmq_setup_basic_desc(&desc, HNS_ROCE_OPC_QUERY_MB_ST,
 					      true);
@@ -2906,10 +2949,8 @@
 
 	hns_roce_cmq_setup_basic_desc(&desc, HNS_ROCE_OPC_CFG_SGID_TB, false);
 
-	roce_set_field(sgid_tb->table_idx_rsv, CFG_SGID_TB_TABLE_IDX_M,
-		       CFG_SGID_TB_TABLE_IDX_S, gid_index);
-	roce_set_field(sgid_tb->vf_sgid_type_rsv, CFG_SGID_TB_VF_SGID_TYPE_M,
-		       CFG_SGID_TB_VF_SGID_TYPE_S, sgid_type);
+	hr_reg_write(sgid_tb, CFG_SGID_TB_TABLE_IDX, gid_index);
+	hr_reg_write(sgid_tb, CFG_SGID_TB_VF_SGID_TYPE, sgid_type);
 
 	copy_gid(&sgid_tb->vf_sgid_l, gid);
 
@@ -2944,19 +2985,14 @@
 
 	copy_gid(&tb_a->vf_sgid_l, gid);
 
-	roce_set_field(tb_a->vf_sgid_type_vlan, CFG_GMV_TB_VF_SGID_TYPE_M,
-		       CFG_GMV_TB_VF_SGID_TYPE_S, sgid_type);
-	roce_set_bit(tb_a->vf_sgid_type_vlan, CFG_GMV_TB_VF_VLAN_EN_S,
-		     vlan_id < VLAN_CFI_MASK);
-	roce_set_field(tb_a->vf_sgid_type_vlan, CFG_GMV_TB_VF_VLAN_ID_M,
-		       CFG_GMV_TB_VF_VLAN_ID_S, vlan_id);
+	hr_reg_write(tb_a, GMV_TB_A_VF_SGID_TYPE, sgid_type);
+	hr_reg_write(tb_a, GMV_TB_A_VF_VLAN_EN, vlan_id < VLAN_CFI_MASK);
+	hr_reg_write(tb_a, GMV_TB_A_VF_VLAN_ID, vlan_id);
 
 	tb_b->vf_smac_l = cpu_to_le32(*(u32 *)mac);
-	roce_set_field(tb_b->vf_smac_h, CFG_GMV_TB_SMAC_H_M,
-		       CFG_GMV_TB_SMAC_H_S, *(u16 *)&mac[4]);
 
-	roce_set_field(tb_b->table_idx_rsv, CFG_GMV_TB_SGID_IDX_M,
-		       CFG_GMV_TB_SGID_IDX_S, gid_index);
+	hr_reg_write(tb_b, GMV_TB_B_SMAC_H, *(u16 *)&mac[4]);
+	hr_reg_write(tb_b, GMV_TB_B_SGID_IDX, gid_index);
 
 	return hns_roce_cmq_send(hr_dev, desc, 2);
 }
@@ -3005,10 +3041,8 @@
 	reg_smac_l = *(u32 *)(&addr[0]);
 	reg_smac_h = *(u16 *)(&addr[4]);
 
-	roce_set_field(smac_tb->tb_idx_rsv, CFG_SMAC_TB_IDX_M,
-		       CFG_SMAC_TB_IDX_S, phy_port);
-	roce_set_field(smac_tb->vf_smac_h_rsv, CFG_SMAC_TB_VF_SMAC_H_M,
-		       CFG_SMAC_TB_VF_SMAC_H_S, reg_smac_h);
+	hr_reg_write(smac_tb, CFG_SMAC_TB_IDX, phy_port);
+	hr_reg_write(smac_tb, CFG_SMAC_TB_VF_SMAC_H, reg_smac_h);
 	smac_tb->vf_smac_l = cpu_to_le32(reg_smac_l);
 
 	return hns_roce_cmq_send(hr_dev, &desc, 1);
@@ -3024,7 +3058,8 @@
 	int i, count;
 
 	count = hns_roce_mtr_find(hr_dev, &mr->pbl_mtr, 0, pages,
-				  ARRAY_SIZE(pages), &pbl_ba);
+				  min_t(int, ARRAY_SIZE(pages), mr->npages),
+				  &pbl_ba);
 	if (count < 1) {
 		ibdev_err(ibdev, "failed to find PBL mtr, count = %d.\n",
 			  count);
@@ -3037,21 +3072,15 @@
 
 	mpt_entry->pbl_size = cpu_to_le32(mr->npages);
 	mpt_entry->pbl_ba_l = cpu_to_le32(pbl_ba >> 3);
-	roce_set_field(mpt_entry->byte_48_mode_ba,
-		       V2_MPT_BYTE_48_PBL_BA_H_M, V2_MPT_BYTE_48_PBL_BA_H_S,
-		       upper_32_bits(pbl_ba >> 3));
+	hr_reg_write(mpt_entry, MPT_PBL_BA_H, upper_32_bits(pbl_ba >> 3));
 
 	mpt_entry->pa0_l = cpu_to_le32(lower_32_bits(pages[0]));
-	roce_set_field(mpt_entry->byte_56_pa0_h, V2_MPT_BYTE_56_PA0_H_M,
-		       V2_MPT_BYTE_56_PA0_H_S, upper_32_bits(pages[0]));
+	hr_reg_write(mpt_entry, MPT_PA0_H, upper_32_bits(pages[0]));
 
 	mpt_entry->pa1_l = cpu_to_le32(lower_32_bits(pages[1]));
-	roce_set_field(mpt_entry->byte_64_buf_pa1, V2_MPT_BYTE_64_PA1_H_M,
-		       V2_MPT_BYTE_64_PA1_H_S, upper_32_bits(pages[1]));
-	roce_set_field(mpt_entry->byte_64_buf_pa1,
-		       V2_MPT_BYTE_64_PBL_BUF_PG_SZ_M,
-		       V2_MPT_BYTE_64_PBL_BUF_PG_SZ_S,
-		       to_hr_hw_page_shift(mr->pbl_mtr.hem_cfg.buf_pg_shift));
+	hr_reg_write(mpt_entry, MPT_PA1_H, upper_32_bits(pages[1]));
+	hr_reg_write(mpt_entry, MPT_PBL_BUF_PG_SZ,
+		     to_hr_hw_page_shift(mr->pbl_mtr.hem_cfg.buf_pg_shift));
 
 	return 0;
 }
@@ -3068,7 +3097,6 @@
 
 	hr_reg_write(mpt_entry, MPT_ST, V2_MPT_ST_VALID);
 	hr_reg_write(mpt_entry, MPT_PD, mr->pd);
-	hr_reg_enable(mpt_entry, MPT_L_INV_EN);
 
 	hr_reg_write_bool(mpt_entry, MPT_BIND_EN,
 			  mr->access & IB_ACCESS_MW_BIND);
@@ -3113,24 +3141,19 @@
 	u32 mr_access_flags = mr->access;
 	int ret = 0;
 
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_MPT_ST_M,
-		       V2_MPT_BYTE_4_MPT_ST_S, V2_MPT_ST_VALID);
-
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_PD_M,
-		       V2_MPT_BYTE_4_PD_S, mr->pd);
+	hr_reg_write(mpt_entry, MPT_ST, V2_MPT_ST_VALID);
+	hr_reg_write(mpt_entry, MPT_PD, mr->pd);
 
 	if (flags & IB_MR_REREG_ACCESS) {
-		roce_set_bit(mpt_entry->byte_8_mw_cnt_en,
-			     V2_MPT_BYTE_8_BIND_EN_S,
+		hr_reg_write(mpt_entry, MPT_BIND_EN,
 			     (mr_access_flags & IB_ACCESS_MW_BIND ? 1 : 0));
-		roce_set_bit(mpt_entry->byte_8_mw_cnt_en,
-			     V2_MPT_BYTE_8_ATOMIC_EN_S,
+		hr_reg_write(mpt_entry, MPT_ATOMIC_EN,
 			     mr_access_flags & IB_ACCESS_REMOTE_ATOMIC ? 1 : 0);
-		roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_RR_EN_S,
+		hr_reg_write(mpt_entry, MPT_RR_EN,
 			     mr_access_flags & IB_ACCESS_REMOTE_READ ? 1 : 0);
-		roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_RW_EN_S,
+		hr_reg_write(mpt_entry, MPT_RW_EN,
 			     mr_access_flags & IB_ACCESS_REMOTE_WRITE ? 1 : 0);
-		roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_LW_EN_S,
+		hr_reg_write(mpt_entry, MPT_LW_EN,
 			     mr_access_flags & IB_ACCESS_LOCAL_WRITE ? 1 : 0);
 	}
 
@@ -3161,37 +3184,27 @@
 		return -ENOBUFS;
 	}
 
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_MPT_ST_M,
-		       V2_MPT_BYTE_4_MPT_ST_S, V2_MPT_ST_FREE);
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_PBL_HOP_NUM_M,
-		       V2_MPT_BYTE_4_PBL_HOP_NUM_S, 1);
-	roce_set_field(mpt_entry->byte_4_pd_hop_st,
-		       V2_MPT_BYTE_4_PBL_BA_PG_SZ_M,
-		       V2_MPT_BYTE_4_PBL_BA_PG_SZ_S,
-		       to_hr_hw_page_shift(mr->pbl_mtr.hem_cfg.ba_pg_shift));
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_PD_M,
-		       V2_MPT_BYTE_4_PD_S, mr->pd);
-
-	roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_RA_EN_S, 1);
-	roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_R_INV_EN_S, 1);
-	roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_L_INV_EN_S, 1);
-
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_FRE_S, 1);
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_PA_S, 0);
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_MR_MW_S, 0);
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_BPD_S, 1);
+	hr_reg_write(mpt_entry, MPT_ST, V2_MPT_ST_FREE);
+	hr_reg_write(mpt_entry, MPT_PD, mr->pd);
+
+	hr_reg_enable(mpt_entry, MPT_RA_EN);
+	hr_reg_enable(mpt_entry, MPT_R_INV_EN);
+
+	hr_reg_enable(mpt_entry, MPT_FRE);
+	hr_reg_clear(mpt_entry, MPT_MR_MW);
+	hr_reg_enable(mpt_entry, MPT_BPD);
+	hr_reg_clear(mpt_entry, MPT_PA);
+
+	hr_reg_write(mpt_entry, MPT_PBL_HOP_NUM, 1);
+	hr_reg_write(mpt_entry, MPT_PBL_BA_PG_SZ,
+		     to_hr_hw_page_shift(mr->pbl_mtr.hem_cfg.ba_pg_shift));
+	hr_reg_write(mpt_entry, MPT_PBL_BUF_PG_SZ,
+		     to_hr_hw_page_shift(mr->pbl_mtr.hem_cfg.buf_pg_shift));
 
 	mpt_entry->pbl_size = cpu_to_le32(mr->npages);
 
 	mpt_entry->pbl_ba_l = cpu_to_le32(lower_32_bits(pbl_ba >> 3));
-	roce_set_field(mpt_entry->byte_48_mode_ba, V2_MPT_BYTE_48_PBL_BA_H_M,
-		       V2_MPT_BYTE_48_PBL_BA_H_S,
-		       upper_32_bits(pbl_ba >> 3));
-
-	roce_set_field(mpt_entry->byte_64_buf_pa1,
-		       V2_MPT_BYTE_64_PBL_BUF_PG_SZ_M,
-		       V2_MPT_BYTE_64_PBL_BUF_PG_SZ_S,
-		       to_hr_hw_page_shift(mr->pbl_mtr.hem_cfg.buf_pg_shift));
+	hr_reg_write(mpt_entry, MPT_PBL_BA_H, upper_32_bits(pbl_ba >> 3));
 
 	return 0;
 }
@@ -3203,36 +3216,28 @@
 	mpt_entry = mb_buf;
 	memset(mpt_entry, 0, sizeof(*mpt_entry));
 
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_MPT_ST_M,
-		       V2_MPT_BYTE_4_MPT_ST_S, V2_MPT_ST_FREE);
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_PD_M,
-		       V2_MPT_BYTE_4_PD_S, mw->pdn);
-	roce_set_field(mpt_entry->byte_4_pd_hop_st, V2_MPT_BYTE_4_PBL_HOP_NUM_M,
-		       V2_MPT_BYTE_4_PBL_HOP_NUM_S,
-		       mw->pbl_hop_num == HNS_ROCE_HOP_NUM_0 ? 0 :
-							       mw->pbl_hop_num);
-	roce_set_field(mpt_entry->byte_4_pd_hop_st,
-		       V2_MPT_BYTE_4_PBL_BA_PG_SZ_M,
-		       V2_MPT_BYTE_4_PBL_BA_PG_SZ_S,
-		       mw->pbl_ba_pg_sz + PG_SHIFT_OFFSET);
-
-	roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_R_INV_EN_S, 1);
-	roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_L_INV_EN_S, 1);
-	roce_set_bit(mpt_entry->byte_8_mw_cnt_en, V2_MPT_BYTE_8_LW_EN_S, 1);
-
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_PA_S, 0);
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_MR_MW_S, 1);
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_BPD_S, 1);
-	roce_set_bit(mpt_entry->byte_12_mw_pa, V2_MPT_BYTE_12_BQP_S,
-		     mw->ibmw.type == IB_MW_TYPE_1 ? 0 : 1);
+	hr_reg_write(mpt_entry, MPT_ST, V2_MPT_ST_FREE);
+	hr_reg_write(mpt_entry, MPT_PD, mw->pdn);
+
+	hr_reg_enable(mpt_entry, MPT_R_INV_EN);
+	hr_reg_enable(mpt_entry, MPT_LW_EN);
 
-	roce_set_field(mpt_entry->byte_64_buf_pa1,
-		       V2_MPT_BYTE_64_PBL_BUF_PG_SZ_M,
-		       V2_MPT_BYTE_64_PBL_BUF_PG_SZ_S,
-		       mw->pbl_buf_pg_sz + PG_SHIFT_OFFSET);
+	hr_reg_enable(mpt_entry, MPT_MR_MW);
+	hr_reg_enable(mpt_entry, MPT_BPD);
+	hr_reg_clear(mpt_entry, MPT_PA);
+	hr_reg_write(mpt_entry, MPT_BQP,
+		     mw->ibmw.type == IB_MW_TYPE_1 ? 0 : 1);
 
 	mpt_entry->lkey = cpu_to_le32(mw->rkey);
 
+	hr_reg_write(mpt_entry, MPT_PBL_HOP_NUM,
+		     mw->pbl_hop_num == HNS_ROCE_HOP_NUM_0 ? 0 :
+							     mw->pbl_hop_num);
+	hr_reg_write(mpt_entry, MPT_PBL_BA_PG_SZ,
+		     mw->pbl_ba_pg_sz + PG_SHIFT_OFFSET);
+	hr_reg_write(mpt_entry, MPT_PBL_BUF_PG_SZ,
+		     mw->pbl_buf_pg_sz + PG_SHIFT_OFFSET);
+
 	return 0;
 }
 
@@ -3328,7 +3333,7 @@
 	memset(cq_context, 0, sizeof(*cq_context));
 
 	hr_reg_write(cq_context, CQC_CQ_ST, V2_CQ_STATE_VALID);
-	hr_reg_write(cq_context, CQC_ARM_ST, REG_NXT_CEQE);
+	hr_reg_write(cq_context, CQC_ARM_ST, NO_ARMED);
 	hr_reg_write(cq_context, CQC_SHIFT, ilog2(hr_cq->cq_depth));
 	hr_reg_write(cq_context, CQC_CEQN, hr_cq->vector);
 	hr_reg_write(cq_context, CQC_CQN, hr_cq->cqn);
@@ -3515,8 +3520,9 @@
 		   wc->status == IB_WC_WR_FLUSH_ERR))
 		return;
 
-	ibdev_err(&hr_dev->ib_dev, "error cqe status 0x%x:\n", cqe_status);
-	print_hex_dump(KERN_ERR, "", DUMP_PREFIX_NONE, 16, 4, cqe,
+	ibdev_err_ratelimited(&hr_dev->ib_dev, "error cqe status 0x%x:\n",
+			      cqe_status);
+	print_hex_dump(KERN_DEBUG, "", DUMP_PREFIX_NONE, 16, 4, cqe,
 		       cq->cqe_size, false);
 	wc->vendor_err = hr_reg_read(cqe, CQE_SUB_STATUS);
 
@@ -3571,7 +3577,6 @@
 	HR_WC_OP_MAP(RDMA_READ,			RDMA_READ),
 	HR_WC_OP_MAP(RDMA_WRITE,		RDMA_WRITE),
 	HR_WC_OP_MAP(RDMA_WRITE_WITH_IMM,	RDMA_WRITE),
-	HR_WC_OP_MAP(LOCAL_INV,			LOCAL_INV),
 	HR_WC_OP_MAP(ATOM_CMP_AND_SWAP,		COMP_SWAP),
 	HR_WC_OP_MAP(ATOM_FETCH_AND_ADD,	FETCH_ADD),
 	HR_WC_OP_MAP(ATOM_MSK_CMP_AND_SWAP,	MASKED_COMP_SWAP),
@@ -3621,9 +3626,6 @@
 	case HNS_ROCE_V2_WQE_OP_RDMA_WRITE_WITH_IMM:
 		wc->wc_flags |= IB_WC_WITH_IMM;
 		break;
-	case HNS_ROCE_V2_WQE_OP_LOCAL_INV:
-		wc->wc_flags |= IB_WC_WITH_INVALIDATE;
-		break;
 	case HNS_ROCE_V2_WQE_OP_ATOM_CMP_AND_SWAP:
 	case HNS_ROCE_V2_WQE_OP_ATOM_FETCH_AND_ADD:
 	case HNS_ROCE_V2_WQE_OP_ATOM_MSK_CMP_AND_SWAP:
@@ -4075,7 +4077,6 @@
 
 static void modify_qp_reset_to_init(struct ib_qp *ibqp,
 				    const struct ib_qp_attr *attr,
-				    int attr_mask,
 				    struct hns_roce_v2_qp_context *context,
 				    struct hns_roce_v2_qp_context *qpc_mask)
 {
@@ -4139,7 +4140,7 @@
 }
 
 static void modify_qp_init_to_init(struct ib_qp *ibqp,
-				   const struct ib_qp_attr *attr, int attr_mask,
+				   const struct ib_qp_attr *attr,
 				   struct hns_roce_v2_qp_context *context,
 				   struct hns_roce_v2_qp_context *qpc_mask)
 {
@@ -4230,12 +4231,14 @@
 		     upper_32_bits(to_hr_hw_page_addr(mtts[0])));
 	hr_reg_clear(qpc_mask, QPC_RQ_CUR_BLK_ADDR_H);
 
-	context->rq_nxt_blk_addr = cpu_to_le32(to_hr_hw_page_addr(mtts[1]));
-	qpc_mask->rq_nxt_blk_addr = 0;
-
-	hr_reg_write(context, QPC_RQ_NXT_BLK_ADDR_H,
-		     upper_32_bits(to_hr_hw_page_addr(mtts[1])));
-	hr_reg_clear(qpc_mask, QPC_RQ_NXT_BLK_ADDR_H);
+	if (hr_dev->pci_dev->revision == PCI_REVISION_ID_HIP08) {
+		context->rq_nxt_blk_addr =
+				cpu_to_le32(to_hr_hw_page_addr(mtts[1]));
+		qpc_mask->rq_nxt_blk_addr = 0;
+		hr_reg_write(context, QPC_RQ_NXT_BLK_ADDR_H,
+			     upper_32_bits(to_hr_hw_page_addr(mtts[1])));
+		hr_reg_clear(qpc_mask, QPC_RQ_NXT_BLK_ADDR_H);
+	}
 
 	return 0;
 }
@@ -4399,11 +4402,9 @@
 	mtu = ib_mtu_enum_to_int(ib_mtu);
 	if (WARN_ON(mtu <= 0))
 		return -EINVAL;
-#define MAX_LP_MSG_LEN 65536
-	/* MTU * (2 ^ LP_PKTN_INI) shouldn't be bigger than 64KB */
-	lp_pktn_ini = ilog2(MAX_LP_MSG_LEN / mtu);
-	if (WARN_ON(lp_pktn_ini >= 0xF))
-		return -EINVAL;
+#define MIN_LP_MSG_LEN 1024
+	/* mtu * (2 ^ lp_pktn_ini) should be in the range of 1024 to mtu */
+	lp_pktn_ini = ilog2(max(mtu, MIN_LP_MSG_LEN) / mtu);
 
 	if (attr_mask & IB_QP_PATH_MTU) {
 		hr_reg_write(context, QPC_MTU, ib_mtu);
@@ -4563,6 +4564,9 @@
 {
 	struct hns_roce_dev *hr_dev = to_hr_dev(ibqp->device);
 
+	if (ibqp->qp_type == IB_QPT_UD)
+		hr_dev->caps.cong_type = CONG_TYPE_DCQCN;
+
 	/* different congestion types match different configurations */
 	switch (hr_dev->caps.cong_type) {
 	case CONG_TYPE_DCQCN:
@@ -4590,10 +4594,15 @@
 		cong_alg->wnd_mode_sel = WND_LIMIT;
 		break;
 	default:
-		ibdev_err(&hr_dev->ib_dev,
-			  "error type(%u) for congestion selection.\n",
-			  hr_dev->caps.cong_type);
-		return -EINVAL;
+		ibdev_warn(&hr_dev->ib_dev,
+			   "invalid type(%u) for congestion selection.\n",
+			   hr_dev->caps.cong_type);
+		hr_dev->caps.cong_type = CONG_TYPE_DCQCN;
+		cong_alg->alg_sel = CONG_DCQCN;
+		cong_alg->alg_sub_sel = UNSUPPORT_CONG_LEVEL;
+		cong_alg->dip_vld = DIP_INVALID;
+		cong_alg->wnd_mode_sel = WND_LIMIT;
+		break;
 	}
 
 	return 0;
@@ -4786,11 +4795,9 @@
 
 	if (cur_state == IB_QPS_RESET && new_state == IB_QPS_INIT) {
 		memset(qpc_mask, 0, hr_dev->caps.qpc_sz);
-		modify_qp_reset_to_init(ibqp, attr, attr_mask, context,
-					qpc_mask);
+		modify_qp_reset_to_init(ibqp, attr, context, qpc_mask);
 	} else if (cur_state == IB_QPS_INIT && new_state == IB_QPS_INIT) {
-		modify_qp_init_to_init(ibqp, attr, attr_mask, context,
-				       qpc_mask);
+		modify_qp_init_to_init(ibqp, attr, context, qpc_mask);
 	} else if (cur_state == IB_QPS_INIT && new_state == IB_QPS_RTR) {
 		ret = modify_qp_init_to_rtr(ibqp, attr, attr_mask, context,
 					    qpc_mask);
@@ -4802,6 +4809,30 @@
 	return ret;
 }
 
+static bool check_qp_timeout_cfg_range(struct hns_roce_dev *hr_dev, u8 *timeout)
+{
+#define QP_ACK_TIMEOUT_MAX_HIP08 20
+#define QP_ACK_TIMEOUT_OFFSET 10
+#define QP_ACK_TIMEOUT_MAX 31
+
+	if (hr_dev->pci_dev->revision == PCI_REVISION_ID_HIP08) {
+		if (*timeout > QP_ACK_TIMEOUT_MAX_HIP08) {
+			ibdev_warn(&hr_dev->ib_dev,
+				   "Local ACK timeout shall be 0 to 20.\n");
+			return false;
+		}
+		*timeout += QP_ACK_TIMEOUT_OFFSET;
+	} else if (hr_dev->pci_dev->revision > PCI_REVISION_ID_HIP08) {
+		if (*timeout > QP_ACK_TIMEOUT_MAX) {
+			ibdev_warn(&hr_dev->ib_dev,
+				   "Local ACK timeout shall be 0 to 31.\n");
+			return false;
+		}
+	}
+
+	return true;
+}
+
 static int hns_roce_v2_set_opt_fields(struct ib_qp *ibqp,
 				      const struct ib_qp_attr *attr,
 				      int attr_mask,
@@ -4811,6 +4842,7 @@
 	struct hns_roce_dev *hr_dev = to_hr_dev(ibqp->device);
 	struct hns_roce_qp *hr_qp = to_hr_qp(ibqp);
 	int ret = 0;
+	u8 timeout;
 
 	if (attr_mask & IB_QP_AV) {
 		ret = hns_roce_v2_set_path(ibqp, attr, attr_mask, context,
@@ -4820,12 +4852,10 @@
 	}
 
 	if (attr_mask & IB_QP_TIMEOUT) {
-		if (attr->timeout < 31) {
-			hr_reg_write(context, QPC_AT, attr->timeout);
+		timeout = attr->timeout;
+		if (check_qp_timeout_cfg_range(hr_dev, &timeout)) {
+			hr_reg_write(context, QPC_AT, timeout);
 			hr_reg_clear(qpc_mask, QPC_AT);
-		} else {
-			ibdev_warn(&hr_dev->ib_dev,
-				   "Local ACK timeout shall be 0 to 30.\n");
 		}
 	}
 
@@ -4882,7 +4912,9 @@
 		set_access_flags(hr_qp, context, qpc_mask, attr, attr_mask);
 
 	if (attr_mask & IB_QP_MIN_RNR_TIMER) {
-		hr_reg_write(context, QPC_MIN_RNR_TIME, attr->min_rnr_timer);
+		hr_reg_write(context, QPC_MIN_RNR_TIME,
+			    hr_dev->pci_dev->revision == PCI_REVISION_ID_HIP08 ?
+			    HNS_ROCE_RNR_TIMER_10NS : attr->min_rnr_timer);
 		hr_reg_clear(qpc_mask, QPC_MIN_RNR_TIME);
 	}
 
@@ -5138,6 +5170,8 @@
 
 		rdma_ah_set_sl(&qp_attr->ah_attr,
 			       hr_reg_read(&context, QPC_SL));
+		rdma_ah_set_port_num(&qp_attr->ah_attr, hr_qp->port + 1);
+		rdma_ah_set_ah_flags(&qp_attr->ah_attr, IB_AH_GRH);
 		grh->flow_label = hr_reg_read(&context, QPC_FL);
 		grh->sgid_index = hr_reg_read(&context, QPC_GMV_IDX);
 		grh->hop_limit = hr_reg_read(&context, QPC_HOPLIMIT);
@@ -5414,7 +5448,7 @@
 
 	/* Resizing SRQs is not supported yet */
 	if (srq_attr_mask & IB_SRQ_MAX_WR)
-		return -EINVAL;
+		return -EOPNOTSUPP;
 
 	if (srq_attr_mask & IB_SRQ_LIMIT) {
 		if (srq_attr->srq_limit > srq->wqe_cnt)
@@ -5499,6 +5533,16 @@
 
 	hr_reg_write(cq_context, CQC_CQ_MAX_CNT, cq_count);
 	hr_reg_clear(cqc_mask, CQC_CQ_MAX_CNT);
+
+	if (hr_dev->pci_dev->revision == PCI_REVISION_ID_HIP08) {
+		if (cq_period * HNS_ROCE_CLOCK_ADJUST > USHRT_MAX) {
+			dev_info(hr_dev->dev,
+				 "cq_period(%u) reached the upper limit, adjusted to 65.\n",
+				 cq_period);
+			cq_period = HNS_ROCE_MAX_CQ_PERIOD;
+		}
+		cq_period *= HNS_ROCE_CLOCK_ADJUST;
+	}
 	hr_reg_write(cq_context, CQC_CQ_PERIOD, cq_period);
 	hr_reg_clear(cqc_mask, CQC_CQ_PERIOD);
 
@@ -5631,12 +5675,12 @@
 		!!(eq->cons_index & eq->entries)) ? aeqe : NULL;
 }
 
-static int hns_roce_v2_aeq_int(struct hns_roce_dev *hr_dev,
-			       struct hns_roce_eq *eq)
+static irqreturn_t hns_roce_v2_aeq_int(struct hns_roce_dev *hr_dev,
+				       struct hns_roce_eq *eq)
 {
 	struct device *dev = hr_dev->dev;
 	struct hns_roce_aeqe *aeqe = next_aeqe_sw_v2(eq);
-	int aeqe_found = 0;
+	irqreturn_t aeqe_found = IRQ_NONE;
 	int event_type;
 	u32 queue_num;
 	int sub_type;
@@ -5696,7 +5740,7 @@
 		eq->event_type = event_type;
 		eq->sub_type = sub_type;
 		++eq->cons_index;
-		aeqe_found = 1;
+		aeqe_found = IRQ_HANDLED;
 
 		hns_roce_v2_init_irq_work(hr_dev, eq, queue_num);
 
@@ -5704,7 +5748,8 @@
 	}
 
 	update_eq_db(eq);
-	return aeqe_found;
+
+	return IRQ_RETVAL(aeqe_found);
 }
 
 static struct hns_roce_ceqe *next_ceqe_sw_v2(struct hns_roce_eq *eq)
@@ -5719,11 +5764,11 @@
 		(!!(eq->cons_index & eq->entries)) ? ceqe : NULL;
 }
 
-static int hns_roce_v2_ceq_int(struct hns_roce_dev *hr_dev,
-			       struct hns_roce_eq *eq)
+static irqreturn_t hns_roce_v2_ceq_int(struct hns_roce_dev *hr_dev,
+				       struct hns_roce_eq *eq)
 {
 	struct hns_roce_ceqe *ceqe = next_ceqe_sw_v2(eq);
-	int ceqe_found = 0;
+	irqreturn_t ceqe_found = IRQ_NONE;
 	u32 cqn;
 
 	while (ceqe) {
@@ -5738,21 +5783,21 @@
 		hns_roce_cq_completion(hr_dev, cqn);
 
 		++eq->cons_index;
-		ceqe_found = 1;
+		ceqe_found = IRQ_HANDLED;
 
 		ceqe = next_ceqe_sw_v2(eq);
 	}
 
 	update_eq_db(eq);
 
-	return ceqe_found;
+	return IRQ_RETVAL(ceqe_found);
 }
 
 static irqreturn_t hns_roce_v2_msix_interrupt_eq(int irq, void *eq_ptr)
 {
 	struct hns_roce_eq *eq = eq_ptr;
 	struct hns_roce_dev *hr_dev = eq->hr_dev;
-	int int_work;
+	irqreturn_t int_work;
 
 	if (eq->type_flag == HNS_ROCE_CEQ)
 		/* Completion event interrupt */
@@ -5764,52 +5809,56 @@
 	return IRQ_RETVAL(int_work);
 }
 
-static irqreturn_t hns_roce_v2_msix_interrupt_abn(int irq, void *dev_id)
+static irqreturn_t abnormal_interrupt_basic(struct hns_roce_dev *hr_dev,
+					    u32 int_st)
 {
-	struct hns_roce_dev *hr_dev = dev_id;
-	struct device *dev = hr_dev->dev;
-	int int_work = 0;
-	u32 int_st;
+	struct pci_dev *pdev = hr_dev->pci_dev;
+	struct hnae3_ae_dev *ae_dev = pci_get_drvdata(pdev);
+	const struct hnae3_ae_ops *ops = ae_dev->ops;
+	enum hnae3_reset_type reset_type;
+	irqreturn_t int_work = IRQ_NONE;
 	u32 int_en;
 
-	/* Abnormal interrupt */
-	int_st = roce_read(hr_dev, ROCEE_VF_ABN_INT_ST_REG);
 	int_en = roce_read(hr_dev, ROCEE_VF_ABN_INT_EN_REG);
 
 	if (int_st & BIT(HNS_ROCE_V2_VF_INT_ST_AEQ_OVERFLOW_S)) {
-		struct pci_dev *pdev = hr_dev->pci_dev;
-		struct hnae3_ae_dev *ae_dev = pci_get_drvdata(pdev);
-		const struct hnae3_ae_ops *ops = ae_dev->ops;
+		dev_err(hr_dev->dev, "AEQ overflow!\n");
 
-		dev_err(dev, "AEQ overflow!\n");
+		roce_write(hr_dev, ROCEE_VF_ABN_INT_ST_REG,
+			   1 << HNS_ROCE_V2_VF_INT_ST_AEQ_OVERFLOW_S);
 
-		int_st |= 1 << HNS_ROCE_V2_VF_INT_ST_AEQ_OVERFLOW_S;
-		roce_write(hr_dev, ROCEE_VF_ABN_INT_ST_REG, int_st);
+		reset_type = hr_dev->is_vf ?
+			     HNAE3_VF_FUNC_RESET : HNAE3_FUNC_RESET;
 
 		/* Set reset level for reset_event() */
 		if (ops->set_default_reset_request)
-			ops->set_default_reset_request(ae_dev,
-						       HNAE3_FUNC_RESET);
+			ops->set_default_reset_request(ae_dev, reset_type);
 		if (ops->reset_event)
 			ops->reset_event(pdev, NULL);
 
 		int_en |= 1 << HNS_ROCE_V2_VF_ABN_INT_EN_S;
 		roce_write(hr_dev, ROCEE_VF_ABN_INT_EN_REG, int_en);
 
-		int_work = 1;
-	} else if (int_st & BIT(HNS_ROCE_V2_VF_INT_ST_RAS_INT_S)) {
-		dev_err(dev, "RAS interrupt!\n");
+		int_work = IRQ_HANDLED;
+	} else {
+		dev_err(hr_dev->dev, "there is no basic abn irq found.\n");
+	}
 
-		int_st |= 1 << HNS_ROCE_V2_VF_INT_ST_RAS_INT_S;
-		roce_write(hr_dev, ROCEE_VF_ABN_INT_ST_REG, int_st);
+	return IRQ_RETVAL(int_work);
+}
 
-		int_en |= 1 << HNS_ROCE_V2_VF_ABN_INT_EN_S;
-		roce_write(hr_dev, ROCEE_VF_ABN_INT_EN_REG, int_en);
+static irqreturn_t hns_roce_v2_msix_interrupt_abn(int irq, void *dev_id)
+{
+	struct hns_roce_dev *hr_dev = dev_id;
+	irqreturn_t int_work = IRQ_NONE;
+	u32 int_st;
 
-		int_work = 1;
-	} else {
-		dev_err(dev, "There is no abnormal irq found!\n");
-	}
+	int_st = roce_read(hr_dev, ROCEE_VF_ABN_INT_ST_REG);
+
+	if (int_st)
+		int_work = abnormal_interrupt_basic(hr_dev, int_st);
+	else
+		dev_err(hr_dev->dev, "there is no abnormal irq found.\n");
 
 	return IRQ_RETVAL(int_work);
 }
@@ -5894,6 +5943,15 @@
 	hr_reg_write(eqc, EQC_EQ_PROD_INDX, HNS_ROCE_EQ_INIT_PROD_IDX);
 	hr_reg_write(eqc, EQC_EQ_MAX_CNT, eq->eq_max_cnt);
 
+	if (hr_dev->pci_dev->revision == PCI_REVISION_ID_HIP08) {
+		if (eq->eq_period * HNS_ROCE_CLOCK_ADJUST > USHRT_MAX) {
+			dev_info(hr_dev->dev, "eq_period(%u) reached the upper limit, adjusted to 65.\n",
+				 eq->eq_period);
+			eq->eq_period = HNS_ROCE_MAX_EQ_PERIOD;
+		}
+		eq->eq_period *= HNS_ROCE_CLOCK_ADJUST;
+	}
+
 	hr_reg_write(eqc, EQC_EQ_PERIOD, eq->eq_period);
 	hr_reg_write(eqc, EQC_EQE_REPORT_TIMER, HNS_ROCE_EQ_INIT_REPORT_TIMER);
 	hr_reg_write(eqc, EQC_EQE_BA_L, bt_ba >> 3);
@@ -6397,10 +6455,8 @@
 	if (!hr_dev)
 		return 0;
 
-	hr_dev->is_reset = true;
 	hr_dev->active = false;
 	hr_dev->dis_db = true;
-
 	hr_dev->state = HNS_ROCE_DEVICE_STATE_RST_DOWN;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_hw_v2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_hw_v2.h
@@ -51,7 +51,7 @@
 #define HNS_ROCE_V2_MAX_SRQ_WR			0x8000
 #define HNS_ROCE_V2_MAX_SRQ_SGE			64
 #define HNS_ROCE_V2_MAX_CQ_NUM			0x100000
-#define HNS_ROCE_V2_MAX_CQC_TIMER_NUM		0x100
+#define HNS_ROCE_V2_MAX_CQC_TIMER_BT_NUM	0x100
 #define HNS_ROCE_V2_MAX_SRQ_NUM			0x100000
 #define HNS_ROCE_V2_MAX_CQE_NUM			0x400000
 #define HNS_ROCE_V2_MAX_SRQWQE_NUM		0x8000
@@ -98,7 +98,7 @@
 
 #define HNS_ROCE_V2_QPC_TIMER_ENTRY_SZ		PAGE_SIZE
 #define HNS_ROCE_V2_CQC_TIMER_ENTRY_SZ		PAGE_SIZE
-#define HNS_ROCE_V2_PAGE_SIZE_SUPPORTED		0xFFFFF000
+#define HNS_ROCE_V2_PAGE_SIZE_SUPPORTED		0xFFFF000
 #define HNS_ROCE_V2_MAX_INNER_MTPT_NUM		2
 #define HNS_ROCE_INVALID_LKEY			0x0
 #define HNS_ROCE_INVALID_SGE_LENGTH		0x80000000
@@ -184,7 +184,6 @@
 	HNS_ROCE_V2_WQE_OP_ATOM_MSK_CMP_AND_SWAP	= 0x8,
 	HNS_ROCE_V2_WQE_OP_ATOM_MSK_FETCH_AND_ADD	= 0x9,
 	HNS_ROCE_V2_WQE_OP_FAST_REG_PMR			= 0xa,
-	HNS_ROCE_V2_WQE_OP_LOCAL_INV			= 0xb,
 	HNS_ROCE_V2_WQE_OP_BIND_MW			= 0xc,
 	HNS_ROCE_V2_WQE_OP_MASK				= 0x1f,
 };
@@ -277,6 +276,11 @@
 	CMD_OTHER_ERR = 0xff
 };
 
+struct hns_roce_cmd_errcode {
+	enum hns_roce_cmd_return_status return_status;
+	int errno;
+};
+
 enum hns_roce_sgid_type {
 	GID_TYPE_FLAG_ROCE_V1 = 0,
 	GID_TYPE_FLAG_ROCE_V2_IPV4,
@@ -790,12 +794,15 @@
 #define MPT_LKEY MPT_FIELD_LOC(223, 192)
 #define MPT_VA MPT_FIELD_LOC(287, 224)
 #define MPT_PBL_SIZE MPT_FIELD_LOC(319, 288)
-#define MPT_PBL_BA MPT_FIELD_LOC(380, 320)
+#define MPT_PBL_BA_L MPT_FIELD_LOC(351, 320)
+#define MPT_PBL_BA_H MPT_FIELD_LOC(380, 352)
 #define MPT_BLK_MODE MPT_FIELD_LOC(381, 381)
 #define MPT_RSV0 MPT_FIELD_LOC(383, 382)
-#define MPT_PA0 MPT_FIELD_LOC(441, 384)
+#define MPT_PA0_L MPT_FIELD_LOC(415, 384)
+#define MPT_PA0_H MPT_FIELD_LOC(441, 416)
 #define MPT_BOUND_VA MPT_FIELD_LOC(447, 442)
-#define MPT_PA1 MPT_FIELD_LOC(505, 448)
+#define MPT_PA1_L MPT_FIELD_LOC(479, 448)
+#define MPT_PA1_H MPT_FIELD_LOC(505, 480)
 #define MPT_PERSIST_EN MPT_FIELD_LOC(506, 506)
 #define MPT_RSV2 MPT_FIELD_LOC(507, 507)
 #define MPT_PBL_BUF_PG_SZ MPT_FIELD_LOC(511, 508)
@@ -901,48 +908,24 @@
 	u8	dgid[GID_LEN_V2];
 };
 
-#define V2_UD_SEND_WQE_BYTE_4_OPCODE_S 0
-#define V2_UD_SEND_WQE_BYTE_4_OPCODE_M GENMASK(4, 0)
-
-#define	V2_UD_SEND_WQE_BYTE_4_OWNER_S 7
-
-#define	V2_UD_SEND_WQE_BYTE_4_CQE_S 8
-
-#define	V2_UD_SEND_WQE_BYTE_4_SE_S 11
-
-#define	V2_UD_SEND_WQE_BYTE_16_PD_S 0
-#define V2_UD_SEND_WQE_BYTE_16_PD_M GENMASK(23, 0)
-
-#define	V2_UD_SEND_WQE_BYTE_16_SGE_NUM_S 24
-#define V2_UD_SEND_WQE_BYTE_16_SGE_NUM_M GENMASK(31, 24)
-
-#define	V2_UD_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_S 0
-#define V2_UD_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_M GENMASK(23, 0)
-
-#define	V2_UD_SEND_WQE_BYTE_24_UDPSPN_S 16
-#define V2_UD_SEND_WQE_BYTE_24_UDPSPN_M GENMASK(31, 16)
+#define UD_SEND_WQE_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_v2_ud_send_wqe, h, l)
 
-#define	V2_UD_SEND_WQE_BYTE_32_DQPN_S 0
-#define V2_UD_SEND_WQE_BYTE_32_DQPN_M GENMASK(23, 0)
-
-#define	V2_UD_SEND_WQE_BYTE_36_VLAN_S 0
-#define V2_UD_SEND_WQE_BYTE_36_VLAN_M GENMASK(15, 0)
-
-#define	V2_UD_SEND_WQE_BYTE_36_HOPLIMIT_S 16
-#define V2_UD_SEND_WQE_BYTE_36_HOPLIMIT_M GENMASK(23, 16)
-
-#define	V2_UD_SEND_WQE_BYTE_36_TCLASS_S 24
-#define V2_UD_SEND_WQE_BYTE_36_TCLASS_M GENMASK(31, 24)
-
-#define	V2_UD_SEND_WQE_BYTE_40_FLOW_LABEL_S 0
-#define V2_UD_SEND_WQE_BYTE_40_FLOW_LABEL_M GENMASK(19, 0)
-
-#define	V2_UD_SEND_WQE_BYTE_40_SL_S 20
-#define V2_UD_SEND_WQE_BYTE_40_SL_M GENMASK(23, 20)
-
-#define V2_UD_SEND_WQE_BYTE_40_UD_VLAN_EN_S 30
-
-#define	V2_UD_SEND_WQE_BYTE_40_LBI_S 31
+#define UD_SEND_WQE_OPCODE UD_SEND_WQE_FIELD_LOC(4, 0)
+#define UD_SEND_WQE_OWNER UD_SEND_WQE_FIELD_LOC(7, 7)
+#define UD_SEND_WQE_CQE UD_SEND_WQE_FIELD_LOC(8, 8)
+#define UD_SEND_WQE_SE UD_SEND_WQE_FIELD_LOC(11, 11)
+#define UD_SEND_WQE_PD UD_SEND_WQE_FIELD_LOC(119, 96)
+#define UD_SEND_WQE_SGE_NUM UD_SEND_WQE_FIELD_LOC(127, 120)
+#define UD_SEND_WQE_MSG_START_SGE_IDX UD_SEND_WQE_FIELD_LOC(151, 128)
+#define UD_SEND_WQE_UDPSPN UD_SEND_WQE_FIELD_LOC(191, 176)
+#define UD_SEND_WQE_DQPN UD_SEND_WQE_FIELD_LOC(247, 224)
+#define UD_SEND_WQE_VLAN UD_SEND_WQE_FIELD_LOC(271, 256)
+#define UD_SEND_WQE_HOPLIMIT UD_SEND_WQE_FIELD_LOC(279, 272)
+#define UD_SEND_WQE_TCLASS UD_SEND_WQE_FIELD_LOC(287, 280)
+#define UD_SEND_WQE_FLOW_LABEL UD_SEND_WQE_FIELD_LOC(307, 288)
+#define UD_SEND_WQE_SL UD_SEND_WQE_FIELD_LOC(311, 308)
+#define UD_SEND_WQE_VLAN_EN UD_SEND_WQE_FIELD_LOC(318, 318)
+#define UD_SEND_WQE_LBI UD_SEND_WQE_FIELD_LOC(319, 319)
 
 struct hns_roce_v2_rc_send_wqe {
 	__le32		byte_4;
@@ -957,42 +940,23 @@
 	__le64		va;
 };
 
-#define	V2_RC_SEND_WQE_BYTE_4_OPCODE_S 0
-#define V2_RC_SEND_WQE_BYTE_4_OPCODE_M GENMASK(4, 0)
-
-#define V2_RC_SEND_WQE_BYTE_4_DB_SL_L_S 5
-#define V2_RC_SEND_WQE_BYTE_4_DB_SL_L_M GENMASK(6, 5)
+#define RC_SEND_WQE_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_v2_rc_send_wqe, h, l)
 
-#define V2_RC_SEND_WQE_BYTE_4_DB_SL_H_S 13
-#define V2_RC_SEND_WQE_BYTE_4_DB_SL_H_M GENMASK(14, 13)
-
-#define V2_RC_SEND_WQE_BYTE_4_WQE_INDEX_S 15
-#define V2_RC_SEND_WQE_BYTE_4_WQE_INDEX_M GENMASK(30, 15)
-
-#define V2_RC_SEND_WQE_BYTE_4_OWNER_S 7
-
-#define V2_RC_SEND_WQE_BYTE_4_CQE_S 8
-
-#define V2_RC_SEND_WQE_BYTE_4_FENCE_S 9
-
-#define V2_RC_SEND_WQE_BYTE_4_SO_S 10
-
-#define V2_RC_SEND_WQE_BYTE_4_SE_S 11
-
-#define V2_RC_SEND_WQE_BYTE_4_INLINE_S 12
-
-#define V2_RC_SEND_WQE_BYTE_4_FLAG_S 31
-
-#define	V2_RC_SEND_WQE_BYTE_16_XRC_SRQN_S 0
-#define V2_RC_SEND_WQE_BYTE_16_XRC_SRQN_M GENMASK(23, 0)
-
-#define	V2_RC_SEND_WQE_BYTE_16_SGE_NUM_S 24
-#define V2_RC_SEND_WQE_BYTE_16_SGE_NUM_M GENMASK(31, 24)
-
-#define V2_RC_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_S 0
-#define V2_RC_SEND_WQE_BYTE_20_MSG_START_SGE_IDX_M GENMASK(23, 0)
-
-#define V2_RC_SEND_WQE_BYTE_20_INL_TYPE_S 31
+#define RC_SEND_WQE_OPCODE RC_SEND_WQE_FIELD_LOC(4, 0)
+#define RC_SEND_WQE_DB_SL_L RC_SEND_WQE_FIELD_LOC(6, 5)
+#define RC_SEND_WQE_DB_SL_H RC_SEND_WQE_FIELD_LOC(14, 13)
+#define RC_SEND_WQE_OWNER RC_SEND_WQE_FIELD_LOC(7, 7)
+#define RC_SEND_WQE_CQE RC_SEND_WQE_FIELD_LOC(8, 8)
+#define RC_SEND_WQE_FENCE RC_SEND_WQE_FIELD_LOC(9, 9)
+#define RC_SEND_WQE_SO RC_SEND_WQE_FIELD_LOC(10, 10)
+#define RC_SEND_WQE_SE RC_SEND_WQE_FIELD_LOC(11, 11)
+#define RC_SEND_WQE_INLINE RC_SEND_WQE_FIELD_LOC(12, 12)
+#define RC_SEND_WQE_WQE_INDEX RC_SEND_WQE_FIELD_LOC(30, 15)
+#define RC_SEND_WQE_FLAG RC_SEND_WQE_FIELD_LOC(31, 31)
+#define RC_SEND_WQE_XRC_SRQN RC_SEND_WQE_FIELD_LOC(119, 96)
+#define RC_SEND_WQE_SGE_NUM RC_SEND_WQE_FIELD_LOC(127, 120)
+#define RC_SEND_WQE_MSG_START_SGE_IDX RC_SEND_WQE_FIELD_LOC(151, 128)
+#define RC_SEND_WQE_INL_TYPE RC_SEND_WQE_FIELD_LOC(159, 159)
 
 struct hns_roce_wqe_frmr_seg {
 	__le32	pbl_size;
@@ -1114,12 +1078,12 @@
 	__le32 resv3;
 };
 
-#define VF_SWITCH_DATA_FUN_ID_VF_ID_S 3
-#define VF_SWITCH_DATA_FUN_ID_VF_ID_M GENMASK(10, 3)
+#define VF_SWITCH_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_vf_switch, h, l)
 
-#define VF_SWITCH_DATA_CFG_ALW_LPBK_S 1
-#define VF_SWITCH_DATA_CFG_ALW_LCL_LPBK_S 2
-#define VF_SWITCH_DATA_CFG_ALW_DST_OVRD_S 3
+#define VF_SWITCH_VF_ID VF_SWITCH_FIELD_LOC(42, 35)
+#define VF_SWITCH_ALW_LPBK VF_SWITCH_FIELD_LOC(65, 65)
+#define VF_SWITCH_ALW_LCL_LPBK VF_SWITCH_FIELD_LOC(66, 66)
+#define VF_SWITCH_ALW_DST_OVRD VF_SWITCH_FIELD_LOC(67, 67)
 
 struct hns_roce_post_mbox {
 	__le32	in_param_l;
@@ -1182,11 +1146,10 @@
 	__le32	vf_sgid_type_rsv;
 };
 
-#define CFG_SGID_TB_TABLE_IDX_S 0
-#define CFG_SGID_TB_TABLE_IDX_M GENMASK(7, 0)
+#define SGID_TB_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_cfg_sgid_tb, h, l)
 
-#define CFG_SGID_TB_VF_SGID_TYPE_S 0
-#define CFG_SGID_TB_VF_SGID_TYPE_M GENMASK(1, 0)
+#define CFG_SGID_TB_TABLE_IDX SGID_TB_FIELD_LOC(7, 0)
+#define CFG_SGID_TB_VF_SGID_TYPE SGID_TB_FIELD_LOC(161, 160)
 
 struct hns_roce_cfg_smac_tb {
 	__le32	tb_idx_rsv;
@@ -1194,11 +1157,11 @@
 	__le32	vf_smac_h_rsv;
 	__le32	rsv[3];
 };
-#define CFG_SMAC_TB_IDX_S 0
-#define CFG_SMAC_TB_IDX_M GENMASK(7, 0)
 
-#define CFG_SMAC_TB_VF_SMAC_H_S 0
-#define CFG_SMAC_TB_VF_SMAC_H_M GENMASK(15, 0)
+#define SMAC_TB_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_cfg_smac_tb, h, l)
+
+#define CFG_SMAC_TB_IDX SMAC_TB_FIELD_LOC(7, 0)
+#define CFG_SMAC_TB_VF_SMAC_H SMAC_TB_FIELD_LOC(79, 64)
 
 struct hns_roce_cfg_gmv_tb_a {
 	__le32 vf_sgid_l;
@@ -1209,16 +1172,11 @@
 	__le32 resv;
 };
 
-#define CFG_GMV_TB_SGID_IDX_S 0
-#define CFG_GMV_TB_SGID_IDX_M GENMASK(7, 0)
+#define GMV_TB_A_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_cfg_gmv_tb_a, h, l)
 
-#define CFG_GMV_TB_VF_SGID_TYPE_S 0
-#define CFG_GMV_TB_VF_SGID_TYPE_M GENMASK(1, 0)
-
-#define CFG_GMV_TB_VF_VLAN_EN_S 2
-
-#define CFG_GMV_TB_VF_VLAN_ID_S 16
-#define CFG_GMV_TB_VF_VLAN_ID_M GENMASK(27, 16)
+#define GMV_TB_A_VF_SGID_TYPE GMV_TB_A_FIELD_LOC(129, 128)
+#define GMV_TB_A_VF_VLAN_EN GMV_TB_A_FIELD_LOC(130, 130)
+#define GMV_TB_A_VF_VLAN_ID GMV_TB_A_FIELD_LOC(155, 144)
 
 struct hns_roce_cfg_gmv_tb_b {
 	__le32	vf_smac_l;
@@ -1227,8 +1185,10 @@
 	__le32	resv[3];
 };
 
-#define CFG_GMV_TB_SMAC_H_S 0
-#define CFG_GMV_TB_SMAC_H_M GENMASK(15, 0)
+#define GMV_TB_B_FIELD_LOC(h, l) FIELD_LOC(struct hns_roce_cfg_gmv_tb_b, h, l)
+
+#define GMV_TB_B_SMAC_H GMV_TB_B_FIELD_LOC(47, 32)
+#define GMV_TB_B_SGID_IDX GMV_TB_B_FIELD_LOC(71, 64)
 
 #define HNS_ROCE_QUERY_PF_CAPS_CMD_NUM 5
 struct hns_roce_query_pf_caps_a {
@@ -1444,6 +1404,14 @@
 	struct list_head node;	/* all dips are on a list */
 };
 
+/* only for RNR timeout issue of HIP08 */
+#define HNS_ROCE_CLOCK_ADJUST 1000
+#define HNS_ROCE_MAX_CQ_PERIOD 65
+#define HNS_ROCE_MAX_EQ_PERIOD 65
+#define HNS_ROCE_RNR_TIMER_10NS 1
+#define HNS_ROCE_1US_CFG 999
+#define HNS_ROCE_1NS_CFG 0
+
 #define HNS_ROCE_AEQ_DEFAULT_BURST_NUM	0x0
 #define HNS_ROCE_AEQ_DEFAULT_INTERVAL	0x0
 #define HNS_ROCE_CEQ_DEFAULT_BURST_NUM	0x0
@@ -1478,7 +1446,6 @@
 #define HNS_ROCE_V2_ASYNC_EQE_NUM		0x1000
 
 #define HNS_ROCE_V2_VF_INT_ST_AEQ_OVERFLOW_S	0
-#define HNS_ROCE_V2_VF_INT_ST_RAS_INT_S		1
 
 #define HNS_ROCE_EQ_DB_CMD_AEQ			0x0
 #define HNS_ROCE_EQ_DB_CMD_AEQ_ARMED		0x1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_main.c
@@ -38,6 +38,7 @@
 #include <rdma/ib_smi.h>
 #include <rdma/ib_user_verbs.h>
 #include <rdma/ib_cache.h>
+#include "hnae3.h"
 #include "hns_roce_common.h"
 #include "hns_roce_device.h"
 #include "hns_roce_hem.h"
@@ -184,7 +185,7 @@
 				  IB_DEVICE_RC_RNR_NAK_GEN;
 	props->max_send_sge = hr_dev->caps.max_sq_sg;
 	props->max_recv_sge = hr_dev->caps.max_rq_sg;
-	props->max_sge_rd = 1;
+	props->max_sge_rd = hr_dev->caps.max_sq_sg;
 	props->max_cq = hr_dev->caps.num_cqs;
 	props->max_cqe = hr_dev->caps.max_cqes;
 	props->max_mr = hr_dev->caps.num_mtpts;
@@ -222,6 +223,7 @@
 	unsigned long flags;
 	enum ib_mtu mtu;
 	u32 port;
+	int ret;
 
 	port = port_num - 1;
 
@@ -234,8 +236,10 @@
 				IB_PORT_BOOT_MGMT_SUP;
 	props->max_msg_sz = HNS_ROCE_MAX_MSG_LEN;
 	props->pkey_tbl_len = 1;
-	props->active_width = IB_WIDTH_4X;
-	props->active_speed = 1;
+	ret = ib_get_eth_speed(ib_dev, port_num, &props->active_speed,
+			       &props->active_width);
+	if (ret)
+		ibdev_warn(ib_dev, "failed to get speed, ret = %d.\n", ret);
 
 	spin_lock_irqsave(&hr_dev->iboe.lock, flags);
 
@@ -269,6 +273,9 @@
 static int hns_roce_query_pkey(struct ib_device *ib_dev, u32 port, u16 index,
 			       u16 *pkey)
 {
+	if (index > 0)
+		return -EINVAL;
+
 	*pkey = PKEY_ID;
 
 	return 0;
@@ -349,7 +356,7 @@
 		return rdma_user_mmap_io(context, vma,
 					 to_hr_ucontext(context)->uar.pfn,
 					 PAGE_SIZE,
-					 pgprot_noncached(vma->vm_page_prot),
+					 pgprot_device(vma->vm_page_prot),
 					 NULL);
 
 	/* vm_pgoff: 1 -- TPTR */
@@ -660,7 +667,7 @@
 		ret = hns_roce_init_hem_table(hr_dev, &hr_dev->cqc_timer_table,
 					      HEM_TYPE_CQC_TIMER,
 					      hr_dev->caps.cqc_timer_entry_sz,
-					      hr_dev->caps.num_cqc_timer, 1);
+					      hr_dev->caps.cqc_timer_bt_num, 1);
 		if (ret) {
 			dev_err(dev,
 				"Failed to init CQC timer memory, aborting.\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_mr.c
@@ -34,6 +34,7 @@
 #include <linux/platform_device.h>
 #include <linux/vmalloc.h>
 #include <rdma/ib_umem.h>
+#include <linux/math.h>
 #include "hns_roce_device.h"
 #include "hns_roce_cmd.h"
 #include "hns_roce_hem.h"
@@ -272,7 +273,6 @@
 		goto err_alloc_pbl;
 
 	mr->ibmr.rkey = mr->ibmr.lkey = mr->key;
-	mr->ibmr.length = length;
 
 	return &mr->ibmr;
 
@@ -416,10 +416,10 @@
 
 	return &mr->ibmr;
 
-err_key:
-	free_mr_key(hr_dev, mr);
 err_pbl:
 	free_mr_pbl(hr_dev, mr);
+err_key:
+	free_mr_key(hr_dev, mr);
 err_free:
 	kfree(mr);
 	return ERR_PTR(ret);
@@ -438,24 +438,30 @@
 }
 
 int hns_roce_map_mr_sg(struct ib_mr *ibmr, struct scatterlist *sg, int sg_nents,
-		       unsigned int *sg_offset)
+		       unsigned int *sg_offset_p)
 {
+	unsigned int sg_offset = sg_offset_p ? *sg_offset_p : 0;
 	struct hns_roce_dev *hr_dev = to_hr_dev(ibmr->device);
 	struct ib_device *ibdev = &hr_dev->ib_dev;
 	struct hns_roce_mr *mr = to_hr_mr(ibmr);
 	struct hns_roce_mtr *mtr = &mr->pbl_mtr;
-	int ret = 0;
+	int ret, sg_num = 0;
+
+	if (!IS_ALIGNED(sg_offset, HNS_ROCE_FRMR_ALIGN_SIZE) ||
+	    ibmr->page_size < HNS_HW_PAGE_SIZE ||
+	    ibmr->page_size > HNS_HW_MAX_PAGE_SIZE)
+		return sg_num;
 
 	mr->npages = 0;
 	mr->page_list = kvcalloc(mr->pbl_mtr.hem_cfg.buf_pg_count,
 				 sizeof(dma_addr_t), GFP_KERNEL);
 	if (!mr->page_list)
-		return ret;
+		return sg_num;
 
-	ret = ib_sg_to_pages(ibmr, sg, sg_nents, sg_offset, hns_roce_set_page);
-	if (ret < 1) {
+	sg_num = ib_sg_to_pages(ibmr, sg, sg_nents, sg_offset_p, hns_roce_set_page);
+	if (sg_num < 1) {
 		ibdev_err(ibdev, "failed to store sg pages %u %u, cnt = %d.\n",
-			  mr->npages, mr->pbl_mtr.hem_cfg.buf_pg_count, ret);
+			  mr->npages, mr->pbl_mtr.hem_cfg.buf_pg_count, sg_num);
 		goto err_page_list;
 	}
 
@@ -466,17 +472,16 @@
 	ret = hns_roce_mtr_map(hr_dev, mtr, mr->page_list, mr->npages);
 	if (ret) {
 		ibdev_err(ibdev, "failed to map sg mtr, ret = %d.\n", ret);
-		ret = 0;
+		sg_num = 0;
 	} else {
 		mr->pbl_mtr.hem_cfg.buf_pg_shift = (u32)ilog2(ibmr->page_size);
-		ret = mr->npages;
 	}
 
 err_page_list:
 	kvfree(mr->page_list);
 	mr->page_list = NULL;
 
-	return ret;
+	return sg_num;
 }
 
 static void hns_roce_mw_free(struct hns_roce_dev *hr_dev,
@@ -609,7 +614,7 @@
 	while (offset < end && npage < max_count) {
 		count = 0;
 		mtts = hns_roce_hem_list_find_mtt(hr_dev, &mtr->hem_list,
-						  offset, &count, NULL);
+						  offset, &count);
 		if (!mtts)
 			return -ENOBUFS;
 
@@ -788,11 +793,6 @@
 	for (i = 0, mapped_cnt = 0; i < mtr->hem_cfg.region_count &&
 	     mapped_cnt < page_cnt; i++) {
 		r = &mtr->hem_cfg.region[i];
-		/* if hopnum is 0, no need to map pages in this region */
-		if (!r->hopnum) {
-			mapped_cnt += r->count;
-			continue;
-		}
 
 		if (r->offset + r->count > page_cnt) {
 			ret = -EINVAL;
@@ -864,7 +864,7 @@
 		mtt_count = 0;
 		mtts = hns_roce_hem_list_find_mtt(hr_dev, &mtr->hem_list,
 						  start_index + total,
-						  &mtt_count, NULL);
+						  &mtt_count);
 		if (!mtts || !mtt_count)
 			goto done;
 
@@ -939,6 +939,44 @@
 	return page_cnt;
 }
 
+static u64 cal_pages_per_l1ba(unsigned int ba_per_bt, unsigned int hopnum)
+{
+	return int_pow(ba_per_bt, hopnum - 1);
+}
+
+static unsigned int cal_best_bt_pg_sz(struct hns_roce_dev *hr_dev,
+				      struct hns_roce_mtr *mtr,
+				      unsigned int pg_shift)
+{
+	unsigned long cap = hr_dev->caps.page_size_cap;
+	struct hns_roce_buf_region *re;
+	unsigned int pgs_per_l1ba;
+	unsigned int ba_per_bt;
+	unsigned int ba_num;
+	int i;
+
+	for_each_set_bit_from(pg_shift, &cap, sizeof(cap) * BITS_PER_BYTE) {
+		if (!(BIT(pg_shift) & cap))
+			continue;
+
+		ba_per_bt = BIT(pg_shift) / BA_BYTE_LEN;
+		ba_num = 0;
+		for (i = 0; i < mtr->hem_cfg.region_count; i++) {
+			re = &mtr->hem_cfg.region[i];
+			if (re->hopnum == 0)
+				continue;
+
+			pgs_per_l1ba = cal_pages_per_l1ba(ba_per_bt, re->hopnum);
+			ba_num += DIV_ROUND_UP(re->count, pgs_per_l1ba);
+		}
+
+		if (ba_num <= ba_per_bt)
+			return pg_shift;
+	}
+
+	return 0;
+}
+
 static int mtr_alloc_mtt(struct hns_roce_dev *hr_dev, struct hns_roce_mtr *mtr,
 			 unsigned int ba_page_shift)
 {
@@ -947,6 +985,10 @@
 
 	hns_roce_hem_list_init(&mtr->hem_list);
 	if (!cfg->is_direct) {
+		ba_page_shift = cal_best_bt_pg_sz(hr_dev, mtr, ba_page_shift);
+		if (!ba_page_shift)
+			return -ERANGE;
+
 		ret = hns_roce_hem_list_request(hr_dev, &mtr->hem_list,
 						cfg->region, cfg->region_count,
 						ba_page_shift);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_pd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_pd.c
@@ -161,7 +161,7 @@
 	int ret;
 
 	if (!(hr_dev->caps.flags & HNS_ROCE_CAP_FLAG_XRC))
-		return -EINVAL;
+		return -EOPNOTSUPP;
 
 	ret = hns_roce_xrcd_alloc(hr_dev, &xrcd->xrcdn);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_qp.c
@@ -172,14 +172,29 @@
 	}
 }
 
-static u8 get_least_load_bankid_for_qp(struct hns_roce_bank *bank)
+static u8 get_affinity_cq_bank(u8 qp_bank)
 {
-	u32 least_load = bank[0].inuse;
+	return (qp_bank >> 1) & CQ_BANKID_MASK;
+}
+
+static u8 get_least_load_bankid_for_qp(struct ib_qp_init_attr *init_attr,
+					struct hns_roce_bank *bank)
+{
+#define INVALID_LOAD_QPNUM 0xFFFFFFFF
+	struct ib_cq *scq = init_attr->send_cq;
+	u32 least_load = INVALID_LOAD_QPNUM;
+	unsigned long cqn = 0;
 	u8 bankid = 0;
 	u32 bankcnt;
 	u8 i;
 
-	for (i = 1; i < HNS_ROCE_QP_BANK_NUM; i++) {
+	if (scq)
+		cqn = to_hr_cq(scq)->cqn;
+
+	for (i = 0; i < HNS_ROCE_QP_BANK_NUM; i++) {
+		if (scq && (get_affinity_cq_bank(i) != (cqn & CQ_BANKID_MASK)))
+			continue;
+
 		bankcnt = bank[i].inuse;
 		if (bankcnt < least_load) {
 			least_load = bankcnt;
@@ -211,7 +226,8 @@
 
 	return 0;
 }
-static int alloc_qpn(struct hns_roce_dev *hr_dev, struct hns_roce_qp *hr_qp)
+static int alloc_qpn(struct hns_roce_dev *hr_dev, struct hns_roce_qp *hr_qp,
+		     struct ib_qp_init_attr *init_attr)
 {
 	struct hns_roce_qp_table *qp_table = &hr_dev->qp_table;
 	unsigned long num = 0;
@@ -229,7 +245,7 @@
 		hr_qp->doorbell_qpn = 1;
 	} else {
 		mutex_lock(&qp_table->bank_mutex);
-		bankid = get_least_load_bankid_for_qp(qp_table->bank);
+		bankid = get_least_load_bankid_for_qp(init_attr, qp_table->bank);
 
 		ret = alloc_qpn_with_bankid(&qp_table->bank[bankid], bankid,
 					    &num);
@@ -495,11 +511,8 @@
 	hr_qp->rq.max_gs = roundup_pow_of_two(max(1U, cap->max_recv_sge) +
 					      hr_qp->rq.rsv_sge);
 
-	if (hr_dev->caps.max_rq_sg <= HNS_ROCE_SGE_IN_WQE)
-		hr_qp->rq.wqe_shift = ilog2(hr_dev->caps.max_rq_desc_sz);
-	else
-		hr_qp->rq.wqe_shift = ilog2(hr_dev->caps.max_rq_desc_sz *
-					    hr_qp->rq.max_gs);
+	hr_qp->rq.wqe_shift = ilog2(hr_dev->caps.max_rq_desc_sz *
+				    hr_qp->rq.max_gs);
 
 	hr_qp->rq.wqe_cnt = cnt;
 	if (hr_dev->caps.flags & HNS_ROCE_CAP_FLAG_RQ_INLINE &&
@@ -829,12 +842,14 @@
 			    struct hns_roce_ib_create_qp *ucmd,
 			    struct hns_roce_ib_create_qp_resp *resp)
 {
+	bool has_sdb = user_qp_has_sdb(hr_dev, init_attr, udata, resp, ucmd);
 	struct hns_roce_ucontext *uctx = rdma_udata_to_drv_context(udata,
 		struct hns_roce_ucontext, ibucontext);
+	bool has_rdb = user_qp_has_rdb(hr_dev, init_attr, udata, resp);
 	struct ib_device *ibdev = &hr_dev->ib_dev;
 	int ret;
 
-	if (user_qp_has_sdb(hr_dev, init_attr, udata, resp, ucmd)) {
+	if (has_sdb) {
 		ret = hns_roce_db_map_user(uctx, ucmd->sdb_addr, &hr_qp->sdb);
 		if (ret) {
 			ibdev_err(ibdev,
@@ -845,7 +860,7 @@
 		hr_qp->en_flags |= HNS_ROCE_QP_CAP_SQ_RECORD_DB;
 	}
 
-	if (user_qp_has_rdb(hr_dev, init_attr, udata, resp)) {
+	if (has_rdb) {
 		ret = hns_roce_db_map_user(uctx, ucmd->db_addr, &hr_qp->rdb);
 		if (ret) {
 			ibdev_err(ibdev,
@@ -859,7 +874,7 @@
 	return 0;
 
 err_sdb:
-	if (hr_qp->en_flags & HNS_ROCE_QP_CAP_SQ_RECORD_DB)
+	if (has_sdb)
 		hns_roce_db_unmap_user(uctx, &hr_qp->sdb);
 err_out:
 	return ret;
@@ -1036,7 +1051,7 @@
 {
 	struct hns_roce_ib_create_qp_resp resp = {};
 	struct ib_device *ibdev = &hr_dev->ib_dev;
-	struct hns_roce_ib_create_qp ucmd;
+	struct hns_roce_ib_create_qp ucmd = {};
 	int ret;
 
 	mutex_init(&hr_qp->mutex);
@@ -1070,7 +1085,7 @@
 		goto err_buf;
 	}
 
-	ret = alloc_qpn(hr_dev, hr_qp);
+	ret = alloc_qpn(hr_dev, hr_qp, init_attr);
 	if (ret) {
 		ibdev_err(ibdev, "failed to alloc QPN, ret = %d.\n", ret);
 		goto err_qpn;
@@ -1102,7 +1117,7 @@
 				       min(udata->outlen, sizeof(resp)));
 		if (ret) {
 			ibdev_err(ibdev, "copy qp resp failed!\n");
-			goto err_store;
+			goto err_flow_ctrl;
 		}
 	}
 
@@ -1349,19 +1364,19 @@
 		__acquire(&send_cq->lock);
 		__acquire(&recv_cq->lock);
 	} else if (unlikely(send_cq != NULL && recv_cq == NULL)) {
-		spin_lock_irq(&send_cq->lock);
+		spin_lock(&send_cq->lock);
 		__acquire(&recv_cq->lock);
 	} else if (unlikely(send_cq == NULL && recv_cq != NULL)) {
-		spin_lock_irq(&recv_cq->lock);
+		spin_lock(&recv_cq->lock);
 		__acquire(&send_cq->lock);
 	} else if (send_cq == recv_cq) {
-		spin_lock_irq(&send_cq->lock);
+		spin_lock(&send_cq->lock);
 		__acquire(&recv_cq->lock);
 	} else if (send_cq->cqn < recv_cq->cqn) {
-		spin_lock_irq(&send_cq->lock);
+		spin_lock(&send_cq->lock);
 		spin_lock_nested(&recv_cq->lock, SINGLE_DEPTH_NESTING);
 	} else {
-		spin_lock_irq(&recv_cq->lock);
+		spin_lock(&recv_cq->lock);
 		spin_lock_nested(&send_cq->lock, SINGLE_DEPTH_NESTING);
 	}
 }
@@ -1381,13 +1396,13 @@
 		spin_unlock(&recv_cq->lock);
 	} else if (send_cq == recv_cq) {
 		__release(&recv_cq->lock);
-		spin_unlock_irq(&send_cq->lock);
+		spin_unlock(&send_cq->lock);
 	} else if (send_cq->cqn < recv_cq->cqn) {
 		spin_unlock(&recv_cq->lock);
-		spin_unlock_irq(&send_cq->lock);
+		spin_unlock(&send_cq->lock);
 	} else {
 		spin_unlock(&send_cq->lock);
-		spin_unlock_irq(&recv_cq->lock);
+		spin_unlock(&recv_cq->lock);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/hns/hns_roce_srq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/hns/hns_roce_srq.c
@@ -100,7 +100,7 @@
 		goto err_out;
 	}
 
-	ret = xa_err(xa_store(&srq_table->xa, srq->srqn, srq, GFP_KERNEL));
+	ret = xa_err(xa_store_irq(&srq_table->xa, srq->srqn, srq, GFP_KERNEL));
 	if (ret) {
 		ibdev_err(ibdev, "failed to store SRQC, ret = %d.\n", ret);
 		goto err_put;
@@ -132,7 +132,7 @@
 err_mbox:
 	hns_roce_free_cmd_mailbox(hr_dev, mailbox);
 err_xa:
-	xa_erase(&srq_table->xa, srq->srqn);
+	xa_erase_irq(&srq_table->xa, srq->srqn);
 err_put:
 	hns_roce_table_put(hr_dev, &srq_table->table, srq->srqn);
 err_out:
@@ -151,7 +151,7 @@
 		dev_err(hr_dev->dev, "DESTROY_SRQ failed (%d) for SRQN %06lx\n",
 			ret, srq->srqn);
 
-	xa_erase(&srq_table->xa, srq->srqn);
+	xa_erase_irq(&srq_table->xa, srq->srqn);
 
 	if (refcount_dec_and_test(&srq->refcount))
 		complete(&srq->free);
@@ -259,7 +259,7 @@
 
 static void free_srq_wrid(struct hns_roce_srq *srq)
 {
-	kfree(srq->wrid);
+	kvfree(srq->wrid);
 	srq->wrid = NULL;
 }
 
@@ -295,7 +295,7 @@
 
 	max_sge = proc_srq_sge(hr_dev, srq, !!udata);
 	if (attr->max_wr > hr_dev->caps.max_srq_wrs ||
-	    attr->max_sge > max_sge) {
+	    attr->max_sge > max_sge || !attr->max_sge) {
 		ibdev_err(&hr_dev->ib_dev,
 			  "invalid SRQ attr, depth = %u, sge = %u.\n",
 			  attr->max_wr, attr->max_sge);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/cm.c
@@ -1458,13 +1458,15 @@
  * irdma_find_listener - find a cm node listening on this addr-port pair
  * @cm_core: cm's core
  * @dst_addr: listener ip addr
+ * @ipv4: flag indicating IPv4 when true
  * @dst_port: listener tcp port num
  * @vlan_id: virtual LAN ID
  * @listener_state: state to match with listen node's
  */
 static struct irdma_cm_listener *
-irdma_find_listener(struct irdma_cm_core *cm_core, u32 *dst_addr, u16 dst_port,
-		    u16 vlan_id, enum irdma_cm_listener_state listener_state)
+irdma_find_listener(struct irdma_cm_core *cm_core, u32 *dst_addr, bool ipv4,
+		    u16 dst_port, u16 vlan_id,
+		    enum irdma_cm_listener_state listener_state)
 {
 	struct irdma_cm_listener *listen_node;
 	static const u32 ip_zero[4] = { 0, 0, 0, 0 };
@@ -1477,12 +1479,13 @@
 	list_for_each_entry (listen_node, &cm_core->listen_list, list) {
 		memcpy(listen_addr, listen_node->loc_addr, sizeof(listen_addr));
 		listen_port = listen_node->loc_port;
+		if (listen_node->ipv4 != ipv4 || listen_port != dst_port ||
+		    !(listener_state & listen_node->listener_state))
+			continue;
 		/* compare node pair, return node handle if a match */
-		if ((!memcmp(listen_addr, dst_addr, sizeof(listen_addr)) ||
-		     !memcmp(listen_addr, ip_zero, sizeof(listen_addr))) &&
-		    listen_port == dst_port &&
-		    vlan_id == listen_node->vlan_id &&
-		    (listener_state & listen_node->listener_state)) {
+		if (!memcmp(listen_addr, ip_zero, sizeof(listen_addr)) ||
+		    (!memcmp(listen_addr, dst_addr, sizeof(listen_addr)) &&
+		     vlan_id == listen_node->vlan_id)) {
 			refcount_inc(&listen_node->refcnt);
 			spin_unlock_irqrestore(&cm_core->listen_list_lock,
 					       flags);
@@ -1501,15 +1504,14 @@
  * @cm_info: CM info for parent listen node
  * @cm_parent_listen_node: The parent listen node
  */
-static enum irdma_status_code
-irdma_del_multiple_qhash(struct irdma_device *iwdev,
-			 struct irdma_cm_info *cm_info,
-			 struct irdma_cm_listener *cm_parent_listen_node)
+static int irdma_del_multiple_qhash(struct irdma_device *iwdev,
+				    struct irdma_cm_info *cm_info,
+				    struct irdma_cm_listener *cm_parent_listen_node)
 {
 	struct irdma_cm_listener *child_listen_node;
-	enum irdma_status_code ret = IRDMA_ERR_CFG;
 	struct list_head *pos, *tpos;
 	unsigned long flags;
+	int ret = -EINVAL;
 
 	spin_lock_irqsave(&iwdev->cm_core.listen_list_lock, flags);
 	list_for_each_safe (pos, tpos,
@@ -1618,16 +1620,16 @@
  * Adds a qhash and a child listen node for every IPv6 address
  * on the adapter and adds the associated qhash filter
  */
-static enum irdma_status_code
-irdma_add_mqh_6(struct irdma_device *iwdev, struct irdma_cm_info *cm_info,
-		struct irdma_cm_listener *cm_parent_listen_node)
+static int irdma_add_mqh_6(struct irdma_device *iwdev,
+			   struct irdma_cm_info *cm_info,
+			   struct irdma_cm_listener *cm_parent_listen_node)
 {
 	struct net_device *ip_dev;
 	struct inet6_dev *idev;
 	struct inet6_ifaddr *ifp, *tmp;
-	enum irdma_status_code ret = 0;
 	struct irdma_cm_listener *child_listen_node;
 	unsigned long flags;
+	int ret = 0;
 
 	rtnl_lock();
 	for_each_netdev(&init_net, ip_dev) {
@@ -1653,7 +1655,7 @@
 				  child_listen_node);
 			if (!child_listen_node) {
 				ibdev_dbg(&iwdev->ibdev, "CM: listener memory allocation\n");
-				ret = IRDMA_ERR_NO_MEMORY;
+				ret = -ENOMEM;
 				goto exit;
 			}
 
@@ -1700,16 +1702,16 @@
  * Adds a qhash and a child listen node for every IPv4 address
  * on the adapter and adds the associated qhash filter
  */
-static enum irdma_status_code
-irdma_add_mqh_4(struct irdma_device *iwdev, struct irdma_cm_info *cm_info,
-		struct irdma_cm_listener *cm_parent_listen_node)
+static int irdma_add_mqh_4(struct irdma_device *iwdev,
+			   struct irdma_cm_info *cm_info,
+			   struct irdma_cm_listener *cm_parent_listen_node)
 {
 	struct net_device *ip_dev;
 	struct in_device *idev;
 	struct irdma_cm_listener *child_listen_node;
-	enum irdma_status_code ret = 0;
 	unsigned long flags;
 	const struct in_ifaddr *ifa;
+	int ret = 0;
 
 	rtnl_lock();
 	for_each_netdev(&init_net, ip_dev) {
@@ -1722,6 +1724,9 @@
 			continue;
 
 		idev = in_dev_get(ip_dev);
+		if (!idev)
+			continue;
+
 		in_dev_for_each_ifa_rtnl(ifa, idev) {
 			ibdev_dbg(&iwdev->ibdev,
 				  "CM: Allocating child CM Listener forIP=%pI4, vlan_id=%d, MAC=%pM\n",
@@ -1734,7 +1739,7 @@
 			if (!child_listen_node) {
 				ibdev_dbg(&iwdev->ibdev, "CM: listener memory allocation\n");
 				in_dev_put(idev);
-				ret = IRDMA_ERR_NO_MEMORY;
+				ret = -ENOMEM;
 				goto exit;
 			}
 
@@ -1781,9 +1786,9 @@
  * @cm_info: CM info for parent listen node
  * @cm_listen_node: The parent listen node
  */
-static enum irdma_status_code
-irdma_add_mqh(struct irdma_device *iwdev, struct irdma_cm_info *cm_info,
-	      struct irdma_cm_listener *cm_listen_node)
+static int irdma_add_mqh(struct irdma_device *iwdev,
+			 struct irdma_cm_info *cm_info,
+			 struct irdma_cm_listener *cm_listen_node)
 {
 	if (cm_info->ipv4)
 		return irdma_add_mqh_4(iwdev, cm_info, cm_listen_node);
@@ -2305,10 +2310,8 @@
 	return NULL;
 }
 
-static void irdma_cm_node_free_cb(struct rcu_head *rcu_head)
+static void irdma_destroy_connection(struct irdma_cm_node *cm_node)
 {
-	struct irdma_cm_node *cm_node =
-			    container_of(rcu_head, struct irdma_cm_node, rcu_head);
 	struct irdma_cm_core *cm_core = cm_node->cm_core;
 	struct irdma_qp *iwqp;
 	struct irdma_cm_info nfo;
@@ -2356,7 +2359,6 @@
 	}
 
 	cm_core->cm_free_ah(cm_node);
-	kfree(cm_node);
 }
 
 /**
@@ -2384,8 +2386,9 @@
 
 	spin_unlock_irqrestore(&cm_core->ht_lock, flags);
 
-	/* wait for all list walkers to exit their grace period */
-	call_rcu(&cm_node->rcu_head, irdma_cm_node_free_cb);
+	irdma_destroy_connection(cm_node);
+
+	kfree_rcu(cm_node, rcu_head);
 }
 
 /**
@@ -2897,9 +2900,10 @@
 	unsigned long flags;
 
 	/* cannot have multiple matching listeners */
-	listener = irdma_find_listener(cm_core, cm_info->loc_addr,
-				       cm_info->loc_port, cm_info->vlan_id,
-				       IRDMA_CM_LISTENER_EITHER_STATE);
+	listener =
+		irdma_find_listener(cm_core, cm_info->loc_addr, cm_info->ipv4,
+				    cm_info->loc_port, cm_info->vlan_id,
+				    IRDMA_CM_LISTENER_EITHER_STATE);
 	if (listener &&
 	    listener->listener_state == IRDMA_CM_LISTENER_ACTIVE_STATE) {
 		refcount_dec(&listener->refcnt);
@@ -3148,6 +3152,7 @@
 
 		listener = irdma_find_listener(cm_core,
 					       cm_info.loc_addr,
+					       cm_info.ipv4,
 					       cm_info.loc_port,
 					       cm_info.vlan_id,
 					       IRDMA_CM_LISTENER_ACTIVE_STATE);
@@ -3201,8 +3206,7 @@
  * @iwdev: iwarp device structure
  * @rdma_ver: HW version
  */
-enum irdma_status_code irdma_setup_cm_core(struct irdma_device *iwdev,
-					   u8 rdma_ver)
+int irdma_setup_cm_core(struct irdma_device *iwdev, u8 rdma_ver)
 {
 	struct irdma_cm_core *cm_core = &iwdev->cm_core;
 
@@ -3212,7 +3216,7 @@
 	/* Handles CM event work items send to Iwarp core */
 	cm_core->event_wq = alloc_ordered_workqueue("iwarp-event-wq", 0);
 	if (!cm_core->event_wq)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	INIT_LIST_HEAD(&cm_core->listen_list);
 
@@ -3244,15 +3248,10 @@
  */
 void irdma_cleanup_cm_core(struct irdma_cm_core *cm_core)
 {
-	unsigned long flags;
-
 	if (!cm_core)
 		return;
 
-	spin_lock_irqsave(&cm_core->ht_lock, flags);
-	if (timer_pending(&cm_core->tcp_timer))
-		del_timer_sync(&cm_core->tcp_timer);
-	spin_unlock_irqrestore(&cm_core->ht_lock, flags);
+	del_timer_sync(&cm_core->tcp_timer);
 
 	destroy_workqueue(cm_core->event_wq);
 	cm_core->dev->ws_reset(&cm_core->iwdev->vsi);
@@ -3465,12 +3464,6 @@
 	}
 
 	cm_id = iwqp->cm_id;
-	/* make sure we havent already closed this connection */
-	if (!cm_id) {
-		spin_unlock_irqrestore(&iwqp->lock, flags);
-		return;
-	}
-
 	original_hw_tcp_state = iwqp->hw_tcp_state;
 	original_ibqp_state = iwqp->ibqp_state;
 	last_ae = iwqp->last_aeq;
@@ -3492,11 +3485,11 @@
 			disconn_status = -ECONNRESET;
 	}
 
-	if ((original_hw_tcp_state == IRDMA_TCP_STATE_CLOSED ||
-	     original_hw_tcp_state == IRDMA_TCP_STATE_TIME_WAIT ||
-	     last_ae == IRDMA_AE_RDMAP_ROE_BAD_LLP_CLOSE ||
-	     last_ae == IRDMA_AE_BAD_CLOSE ||
-	     last_ae == IRDMA_AE_LLP_CONNECTION_RESET || iwdev->rf->reset)) {
+	if (original_hw_tcp_state == IRDMA_TCP_STATE_CLOSED ||
+	    original_hw_tcp_state == IRDMA_TCP_STATE_TIME_WAIT ||
+	    last_ae == IRDMA_AE_RDMAP_ROE_BAD_LLP_CLOSE ||
+	    last_ae == IRDMA_AE_BAD_CLOSE ||
+	    last_ae == IRDMA_AE_LLP_CONNECTION_RESET || iwdev->rf->reset || !cm_id) {
 		issue_close = 1;
 		iwqp->cm_id = NULL;
 		qp->term_flags = 0;
@@ -3587,7 +3580,7 @@
 /**
  * irdma_accept - registered call for connection to be accepted
  * @cm_id: cm information for passive connection
- * @conn_param: accpet parameters
+ * @conn_param: accept parameters
  */
 int irdma_accept(struct iw_cm_id *cm_id, struct iw_cm_conn_param *conn_param)
 {
@@ -3915,10 +3908,10 @@
 	struct irdma_device *iwdev;
 	struct irdma_cm_listener *cm_listen_node;
 	struct irdma_cm_info cm_info = {};
-	enum irdma_status_code err;
 	struct sockaddr_in *laddr;
 	struct sockaddr_in6 *laddr6;
 	bool wildcard = false;
+	int err;
 
 	iwdev = to_iwdev(cm_id->device);
 	if (!iwdev)
@@ -4234,10 +4227,6 @@
 	struct irdma_cm_node *cm_node;
 	struct list_head teardown_list;
 	struct ib_qp_attr attr;
-	struct irdma_sc_vsi *vsi = &iwdev->vsi;
-	struct irdma_sc_qp *sc_qp;
-	struct irdma_qp *qp;
-	int i;
 
 	INIT_LIST_HEAD(&teardown_list);
 
@@ -4254,52 +4243,6 @@
 			irdma_cm_disconn(cm_node->iwqp);
 		irdma_rem_ref_cm_node(cm_node);
 	}
-	if (!iwdev->roce_mode)
-		return;
-
-	INIT_LIST_HEAD(&teardown_list);
-	for (i = 0; i < IRDMA_MAX_USER_PRIORITY; i++) {
-		mutex_lock(&vsi->qos[i].qos_mutex);
-		list_for_each_safe (list_node, list_core_temp,
-				    &vsi->qos[i].qplist) {
-			u32 qp_ip[4];
-
-			sc_qp = container_of(list_node, struct irdma_sc_qp,
-					     list);
-			if (sc_qp->qp_uk.qp_type != IRDMA_QP_TYPE_ROCE_RC)
-				continue;
-
-			qp = sc_qp->qp_uk.back_qp;
-			if (!disconnect_all) {
-				if (nfo->ipv4)
-					qp_ip[0] = qp->udp_info.local_ipaddr[3];
-				else
-					memcpy(qp_ip,
-					       &qp->udp_info.local_ipaddr[0],
-					       sizeof(qp_ip));
-			}
-
-			if (disconnect_all ||
-			    (nfo->vlan_id == (qp->udp_info.vlan_tag & VLAN_VID_MASK) &&
-			     !memcmp(qp_ip, ipaddr, nfo->ipv4 ? 4 : 16))) {
-				spin_lock(&iwdev->rf->qptable_lock);
-				if (iwdev->rf->qp_table[sc_qp->qp_uk.qp_id]) {
-					irdma_qp_add_ref(&qp->ibqp);
-					list_add(&qp->teardown_entry,
-						 &teardown_list);
-				}
-				spin_unlock(&iwdev->rf->qptable_lock);
-			}
-		}
-		mutex_unlock(&vsi->qos[i].qos_mutex);
-	}
-
-	list_for_each_safe (list_node, list_core_temp, &teardown_list) {
-		qp = container_of(list_node, struct irdma_qp, teardown_entry);
-		attr.qp_state = IB_QPS_ERR;
-		irdma_modify_qp_roce(&qp->ibqp, &attr, IB_QP_STATE, NULL);
-		irdma_qp_rem_ref(&qp->ibqp);
-	}
 }
 
 /**
@@ -4325,11 +4268,11 @@
 	struct list_head *child_listen_list = &parent_listen_node->child_listen_list;
 	struct irdma_cm_listener *child_listen_node;
 	struct list_head *pos, *tpos;
-	enum irdma_status_code err;
 	bool node_allocated = false;
 	enum irdma_quad_hash_manage_type op = ifup ?
 					      IRDMA_QHASH_MANAGE_TYPE_ADD :
 					      IRDMA_QHASH_MANAGE_TYPE_DELETE;
+	int err;
 
 	list_for_each_safe (pos, tpos, child_listen_list) {
 		child_listen_node = list_entry(pos, struct irdma_cm_listener,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/cm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/cm.h
@@ -41,7 +41,7 @@
 #define TCP_OPTIONS_PADDING	3
 
 #define IRDMA_DEFAULT_RETRYS	64
-#define IRDMA_DEFAULT_RETRANS	8
+#define IRDMA_DEFAULT_RETRANS	32
 #define IRDMA_DEFAULT_TTL		0x40
 #define IRDMA_DEFAULT_RTT_VAR		6
 #define IRDMA_DEFAULT_SS_THRESH		0x3fffffff
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/ctrl.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2015 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "hmc.h"
 #include "defs.h"
 #include "type.h"
@@ -152,17 +151,16 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_add_arp_cache_entry(struct irdma_sc_cqp *cqp,
-			     struct irdma_add_arp_cache_entry_info *info,
-			     u64 scratch, bool post_sq)
+static int irdma_sc_add_arp_cache_entry(struct irdma_sc_cqp *cqp,
+					struct irdma_add_arp_cache_entry_info *info,
+					u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	set_64bit_val(wqe, 8, info->reach_max);
 	set_64bit_val(wqe, 16, ether_addr_to_u64(info->mac_addr));
 
@@ -190,16 +188,15 @@
  * @arp_index: arp index to delete arp entry
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_del_arp_cache_entry(struct irdma_sc_cqp *cqp, u64 scratch,
-			     u16 arp_index, bool post_sq)
+static int irdma_sc_del_arp_cache_entry(struct irdma_sc_cqp *cqp, u64 scratch,
+					u16 arp_index, bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	hdr = arp_index |
 	      FIELD_PREP(IRDMA_CQPSQ_OPCODE, IRDMA_CQP_OP_MANAGE_ARP) |
@@ -224,17 +221,16 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_manage_apbvt_entry(struct irdma_sc_cqp *cqp,
-			    struct irdma_apbvt_info *info, u64 scratch,
-			    bool post_sq)
+static int irdma_sc_manage_apbvt_entry(struct irdma_sc_cqp *cqp,
+				       struct irdma_apbvt_info *info,
+				       u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, info->port);
 
@@ -272,7 +268,7 @@
  * quad hash entry in the hardware will point to iwarp's qp
  * number and requires no calls from the driver.
  */
-static enum irdma_status_code
+static int
 irdma_sc_manage_qhash_table_entry(struct irdma_sc_cqp *cqp,
 				  struct irdma_qhash_table_info *info,
 				  u64 scratch, bool post_sq)
@@ -285,7 +281,7 @@
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 0, ether_addr_to_u64(info->mac_addr));
 
@@ -348,10 +344,9 @@
  * @qp: sc qp
  * @info: initialization qp info
  */
-enum irdma_status_code irdma_sc_qp_init(struct irdma_sc_qp *qp,
-					struct irdma_qp_init_info *info)
+int irdma_sc_qp_init(struct irdma_sc_qp *qp, struct irdma_qp_init_info *info)
 {
-	enum irdma_status_code ret_code;
+	int ret_code;
 	u32 pble_obj_cnt;
 	u16 wqe_size;
 
@@ -359,7 +354,7 @@
 	    info->pd->dev->hw_attrs.uk_attrs.max_hw_wq_frags ||
 	    info->qp_uk_init_info.max_rq_frag_cnt >
 	    info->pd->dev->hw_attrs.uk_attrs.max_hw_wq_frags)
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 
 	qp->dev = info->pd->dev;
 	qp->vsi = info->vsi;
@@ -382,7 +377,7 @@
 
 	if ((info->virtual_map && info->sq_pa >= pble_obj_cnt) ||
 	    (info->virtual_map && info->rq_pa >= pble_obj_cnt))
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	qp->llp_stream_handle = (void *)(-1);
 	qp->hw_sq_size = irdma_get_encoded_wqe_size(qp->qp_uk.sq_ring.size,
@@ -422,8 +417,8 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_qp_create(struct irdma_sc_qp *qp, struct irdma_create_qp_info *info,
-					  u64 scratch, bool post_sq)
+int irdma_sc_qp_create(struct irdma_sc_qp *qp, struct irdma_create_qp_info *info,
+		       u64 scratch, bool post_sq)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
@@ -431,12 +426,12 @@
 
 	cqp = qp->dev->cqp;
 	if (qp->qp_uk.qp_id < cqp->dev->hw_attrs.min_hw_qp_id ||
-	    qp->qp_uk.qp_id > (cqp->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_QP].max_cnt - 1))
-		return IRDMA_ERR_INVALID_QP_ID;
+	    qp->qp_uk.qp_id >= (cqp->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_QP].max_cnt))
+		return -EINVAL;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, qp->hw_host_ctx_pa);
 	set_64bit_val(wqe, 40, qp->shadow_area_pa);
@@ -473,9 +468,8 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_qp_modify(struct irdma_sc_qp *qp,
-					  struct irdma_modify_qp_info *info,
-					  u64 scratch, bool post_sq)
+int irdma_sc_qp_modify(struct irdma_sc_qp *qp, struct irdma_modify_qp_info *info,
+		       u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
@@ -486,7 +480,7 @@
 	cqp = qp->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	if (info->next_iwarp_state == IRDMA_QP_STATE_TERMINATE) {
 		if (info->dont_send_fin)
@@ -544,9 +538,8 @@
  * @ignore_mw_bnd: memory window bind flag
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_qp_destroy(struct irdma_sc_qp *qp, u64 scratch,
-					   bool remove_hash_idx, bool ignore_mw_bnd,
-					   bool post_sq)
+int irdma_sc_qp_destroy(struct irdma_sc_qp *qp, u64 scratch,
+			bool remove_hash_idx, bool ignore_mw_bnd, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
@@ -555,7 +548,7 @@
 	cqp = qp->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, qp->hw_host_ctx_pa);
 	set_64bit_val(wqe, 40, qp->shadow_area_pa);
@@ -737,16 +730,15 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_alloc_local_mac_entry(struct irdma_sc_cqp *cqp, u64 scratch,
-			       bool post_sq)
+static int irdma_sc_alloc_local_mac_entry(struct irdma_sc_cqp *cqp, u64 scratch,
+					  bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	hdr = FIELD_PREP(IRDMA_CQPSQ_OPCODE,
 			 IRDMA_CQP_OP_ALLOCATE_LOC_MAC_TABLE_ENTRY) |
@@ -772,17 +764,16 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_add_local_mac_entry(struct irdma_sc_cqp *cqp,
-			     struct irdma_local_mac_entry_info *info,
-			     u64 scratch, bool post_sq)
+static int irdma_sc_add_local_mac_entry(struct irdma_sc_cqp *cqp,
+					struct irdma_local_mac_entry_info *info,
+					u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	u64 header;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 32, ether_addr_to_u64(info->mac_addr));
 
@@ -811,16 +802,16 @@
  * @ignore_ref_count: to force mac adde delete
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_del_local_mac_entry(struct irdma_sc_cqp *cqp, u64 scratch,
-			     u16 entry_idx, u8 ignore_ref_count, bool post_sq)
+static int irdma_sc_del_local_mac_entry(struct irdma_sc_cqp *cqp, u64 scratch,
+					u16 entry_idx, u8 ignore_ref_count,
+					bool post_sq)
 {
 	__le64 *wqe;
 	u64 header;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	header = FIELD_PREP(IRDMA_CQPSQ_MLM_TABLEIDX, entry_idx) |
 		 FIELD_PREP(IRDMA_CQPSQ_OPCODE,
 			    IRDMA_CQP_OP_MANAGE_LOC_MAC_TABLE) |
@@ -1033,16 +1024,18 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_alloc_stag(struct irdma_sc_dev *dev,
-		    struct irdma_allocate_stag_info *info, u64 scratch,
-		    bool post_sq)
+static int irdma_sc_alloc_stag(struct irdma_sc_dev *dev,
+			       struct irdma_allocate_stag_info *info,
+			       u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
 	u64 hdr;
 	enum irdma_page_size page_size;
 
+	if (!info->total_len && !info->all_memory)
+		return -EINVAL;
+
 	if (info->page_size == 0x40000000)
 		page_size = IRDMA_PAGE_SIZE_1G;
 	else if (info->page_size == 0x200000)
@@ -1053,7 +1046,7 @@
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 8,
 		      FLD_LS_64(dev, info->pd_id, IRDMA_CQPSQ_STAG_PDID) |
@@ -1095,10 +1088,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_mr_reg_non_shared(struct irdma_sc_dev *dev,
-			   struct irdma_reg_ns_stag_info *info, u64 scratch,
-			   bool post_sq)
+static int irdma_sc_mr_reg_non_shared(struct irdma_sc_dev *dev,
+				      struct irdma_reg_ns_stag_info *info,
+				      u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	u64 fbo;
@@ -1109,6 +1101,9 @@
 	u8 addr_type;
 	enum irdma_page_size page_size;
 
+	if (!info->total_len && !info->all_memory)
+		return -EINVAL;
+
 	if (info->page_size == 0x40000000)
 		page_size = IRDMA_PAGE_SIZE_1G;
 	else if (info->page_size == 0x200000)
@@ -1116,7 +1111,7 @@
 	else if (info->page_size == 0x1000)
 		page_size = IRDMA_PAGE_SIZE_4K;
 	else
-		return IRDMA_ERR_PARAM;
+		return -EINVAL;
 
 	if (info->access_rights & (IRDMA_ACCESS_FLAGS_REMOTEREAD_ONLY |
 				   IRDMA_ACCESS_FLAGS_REMOTEWRITE_ONLY))
@@ -1126,12 +1121,12 @@
 
 	pble_obj_cnt = dev->hmc_info->hmc_obj[IRDMA_HMC_IW_PBLE].cnt;
 	if (info->chunk_size && info->first_pm_pbl_index >= pble_obj_cnt)
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	fbo = info->va & (info->page_size - 1);
 
 	set_64bit_val(wqe, 0,
@@ -1184,10 +1179,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_dealloc_stag(struct irdma_sc_dev *dev,
-		      struct irdma_dealloc_stag_info *info, u64 scratch,
-		      bool post_sq)
+static int irdma_sc_dealloc_stag(struct irdma_sc_dev *dev,
+				 struct irdma_dealloc_stag_info *info,
+				 u64 scratch, bool post_sq)
 {
 	u64 hdr;
 	__le64 *wqe;
@@ -1196,7 +1190,7 @@
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 8,
 		      FLD_LS_64(dev, info->pd_id, IRDMA_CQPSQ_STAG_PDID));
@@ -1225,9 +1219,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_mw_alloc(struct irdma_sc_dev *dev, struct irdma_mw_alloc_info *info,
-		  u64 scratch, bool post_sq)
+static int irdma_sc_mw_alloc(struct irdma_sc_dev *dev,
+			     struct irdma_mw_alloc_info *info, u64 scratch,
+			     bool post_sq)
 {
 	u64 hdr;
 	struct irdma_sc_cqp *cqp;
@@ -1236,7 +1230,7 @@
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 8,
 		      FLD_LS_64(dev, info->pd_id, IRDMA_CQPSQ_STAG_PDID));
@@ -1266,9 +1260,9 @@
  * @info: fast mr info
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code
-irdma_sc_mr_fast_register(struct irdma_sc_qp *qp,
-			  struct irdma_fast_reg_stag_info *info, bool post_sq)
+int irdma_sc_mr_fast_register(struct irdma_sc_qp *qp,
+			      struct irdma_fast_reg_stag_info *info,
+			      bool post_sq)
 {
 	u64 temp, hdr;
 	__le64 *wqe;
@@ -1290,7 +1284,7 @@
 	wqe = irdma_qp_get_next_send_wqe(&qp->qp_uk, &wqe_idx,
 					 IRDMA_QP_WQE_MIN_QUANTA, 0, &sq_info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(&qp->qp_uk, wqe_idx);
 
@@ -1420,44 +1414,6 @@
 }
 
 /**
- * irdma_sc_send_lsmm_nostag - for privilege qp
- * @qp: sc qp struct
- * @lsmm_buf: buffer with lsmm message
- * @size: size of lsmm buffer
- */
-void irdma_sc_send_lsmm_nostag(struct irdma_sc_qp *qp, void *lsmm_buf, u32 size)
-{
-	__le64 *wqe;
-	u64 hdr;
-	struct irdma_qp_uk *qp_uk;
-
-	qp_uk = &qp->qp_uk;
-	wqe = qp_uk->sq_base->elem;
-
-	set_64bit_val(wqe, 0, (uintptr_t)lsmm_buf);
-
-	if (qp->qp_uk.uk_attrs->hw_rev == IRDMA_GEN_1)
-		set_64bit_val(wqe, 8,
-			      FIELD_PREP(IRDMAQPSQ_GEN1_FRAG_LEN, size));
-	else
-		set_64bit_val(wqe, 8,
-			      FIELD_PREP(IRDMAQPSQ_FRAG_LEN, size) |
-			      FIELD_PREP(IRDMAQPSQ_VALID, qp->qp_uk.swqe_polarity));
-	set_64bit_val(wqe, 16, 0);
-
-	hdr = FIELD_PREP(IRDMAQPSQ_OPCODE, IRDMAQP_OP_RDMA_SEND) |
-	      FIELD_PREP(IRDMAQPSQ_STREAMMODE, 1) |
-	      FIELD_PREP(IRDMAQPSQ_WAITFORRCVPDU, 1) |
-	      FIELD_PREP(IRDMAQPSQ_VALID, qp->qp_uk.swqe_polarity);
-	dma_wmb(); /* make sure WQE is written before valid bit is set */
-
-	set_64bit_val(wqe, 24, hdr);
-
-	print_hex_dump_debug("WQE: SEND_LSMM_NOSTAG WQE", DUMP_PREFIX_OFFSET,
-			     16, 8, wqe, IRDMA_QP_WQE_MIN_SIZE, false);
-}
-
-/**
  * irdma_sc_send_rtt - send last read0 or write0
  * @qp: sc qp struct
  * @read: Do read0 or write0
@@ -1857,8 +1813,7 @@
 	}
 }
 
-static enum irdma_status_code irdma_null_ws_add(struct irdma_sc_vsi *vsi,
-						u8 user_pri)
+static int irdma_null_ws_add(struct irdma_sc_vsi *vsi, u8 user_pri)
 {
 	return 0;
 }
@@ -1954,8 +1909,8 @@
  * @vsi: pointer to the vsi structure
  * @info: The info structure used for initialization
  */
-enum irdma_status_code irdma_vsi_stats_init(struct irdma_sc_vsi *vsi,
-					    struct irdma_vsi_stats_info *info)
+int irdma_vsi_stats_init(struct irdma_sc_vsi *vsi,
+			 struct irdma_vsi_stats_info *info)
 {
 	u8 fcn_id = info->fcn_id;
 	struct irdma_dma_mem *stats_buff_mem;
@@ -1970,7 +1925,7 @@
 						&stats_buff_mem->pa,
 						GFP_KERNEL);
 	if (!stats_buff_mem->va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	vsi->pestat->gather_info.gather_stats_va = stats_buff_mem->va;
 	vsi->pestat->gather_info.last_gather_stats_va =
@@ -1997,7 +1952,7 @@
 			  stats_buff_mem->va, stats_buff_mem->pa);
 	stats_buff_mem->va = NULL;
 
-	return IRDMA_ERR_CQP_COMPL_ERROR;
+	return -EIO;
 }
 
 /**
@@ -2059,19 +2014,19 @@
  * @info: gather stats info structure
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code
-irdma_sc_gather_stats(struct irdma_sc_cqp *cqp,
-		      struct irdma_stats_gather_info *info, u64 scratch)
+static int irdma_sc_gather_stats(struct irdma_sc_cqp *cqp,
+				 struct irdma_stats_gather_info *info,
+				 u64 scratch)
 {
 	__le64 *wqe;
 	u64 temp;
 
 	if (info->stats_buff_mem.size < IRDMA_GATHER_STATS_BUF_SIZE)
-		return IRDMA_ERR_BUF_TOO_SHORT;
+		return -ENOMEM;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 40,
 		      FIELD_PREP(IRDMA_CQPSQ_STATS_HMC_FCN_INDEX, info->hmc_fcn_index));
@@ -2106,17 +2061,16 @@
  * @alloc: alloc vs. delete flag
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code
-irdma_sc_manage_stats_inst(struct irdma_sc_cqp *cqp,
-			   struct irdma_stats_inst_info *info, bool alloc,
-			   u64 scratch)
+static int irdma_sc_manage_stats_inst(struct irdma_sc_cqp *cqp,
+				      struct irdma_stats_inst_info *info,
+				      bool alloc, u64 scratch)
 {
 	__le64 *wqe;
 	u64 temp;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 40,
 		      FIELD_PREP(IRDMA_CQPSQ_STATS_HMC_FCN_INDEX, info->hmc_fn_id));
@@ -2144,9 +2098,8 @@
  * @info: User priority map info
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code irdma_sc_set_up_map(struct irdma_sc_cqp *cqp,
-						  struct irdma_up_info *info,
-						  u64 scratch)
+static int irdma_sc_set_up_map(struct irdma_sc_cqp *cqp,
+			       struct irdma_up_info *info, u64 scratch)
 {
 	__le64 *wqe;
 	u64 temp = 0;
@@ -2154,7 +2107,7 @@
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	for (i = 0; i < IRDMA_MAX_USER_PRIORITY; i++)
 		temp |= (u64)info->map[i] << (i * 8);
@@ -2187,17 +2140,16 @@
  * @node_op: 0 for add 1 for modify, 2 for delete
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code
-irdma_sc_manage_ws_node(struct irdma_sc_cqp *cqp,
-			struct irdma_ws_node_info *info,
-			enum irdma_ws_node_op node_op, u64 scratch)
+static int irdma_sc_manage_ws_node(struct irdma_sc_cqp *cqp,
+				   struct irdma_ws_node_info *info,
+				   enum irdma_ws_node_op node_op, u64 scratch)
 {
 	__le64 *wqe;
 	u64 temp = 0;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 32,
 		      FIELD_PREP(IRDMA_CQPSQ_WS_VSI, info->vsi) |
@@ -2230,9 +2182,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_qp_flush_wqes(struct irdma_sc_qp *qp,
-					      struct irdma_qp_flush_info *info,
-					      u64 scratch, bool post_sq)
+int irdma_sc_qp_flush_wqes(struct irdma_sc_qp *qp,
+			   struct irdma_qp_flush_info *info, u64 scratch,
+			   bool post_sq)
 {
 	u64 temp = 0;
 	__le64 *wqe;
@@ -2251,13 +2203,13 @@
 		ibdev_dbg(to_ibdev(qp->dev),
 			  "CQP: Additional flush request ignored for qp %x\n",
 			  qp->qp_uk.qp_id);
-		return IRDMA_ERR_FLUSHED_Q;
+		return -EALREADY;
 	}
 
 	cqp = qp->pd->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	if (info->userflushcode) {
 		if (flush_rq)
@@ -2304,9 +2256,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code irdma_sc_gen_ae(struct irdma_sc_qp *qp,
-					      struct irdma_gen_ae_info *info,
-					      u64 scratch, bool post_sq)
+static int irdma_sc_gen_ae(struct irdma_sc_qp *qp,
+			   struct irdma_gen_ae_info *info, u64 scratch,
+			   bool post_sq)
 {
 	u64 temp;
 	__le64 *wqe;
@@ -2316,7 +2268,7 @@
 	cqp = qp->pd->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	temp = info->ae_code | FIELD_PREP(IRDMA_CQPSQ_FWQE_AESOURCE,
 					  info->ae_src);
@@ -2344,10 +2296,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_qp_upload_context(struct irdma_sc_dev *dev,
-			   struct irdma_upload_context_info *info, u64 scratch,
-			   bool post_sq)
+static int irdma_sc_qp_upload_context(struct irdma_sc_dev *dev,
+				      struct irdma_upload_context_info *info,
+				      u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
@@ -2356,7 +2307,7 @@
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, info->buf_pa);
 
@@ -2385,21 +2336,20 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_manage_push_page(struct irdma_sc_cqp *cqp,
-			  struct irdma_cqp_manage_push_page_info *info,
-			  u64 scratch, bool post_sq)
+static int irdma_sc_manage_push_page(struct irdma_sc_cqp *cqp,
+				     struct irdma_cqp_manage_push_page_info *info,
+				     u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
 
 	if (info->free_page &&
 	    info->push_idx >= cqp->dev->hw_attrs.max_hw_device_pages)
-		return IRDMA_ERR_INVALID_PUSH_PAGE_INDEX;
+		return -EINVAL;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, info->qs_handle);
 	hdr = FIELD_PREP(IRDMA_CQPSQ_MPP_PPIDX, info->push_idx) |
@@ -2425,16 +2375,15 @@
  * @qp: sc qp struct
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code irdma_sc_suspend_qp(struct irdma_sc_cqp *cqp,
-						  struct irdma_sc_qp *qp,
-						  u64 scratch)
+static int irdma_sc_suspend_qp(struct irdma_sc_cqp *cqp, struct irdma_sc_qp *qp,
+			       u64 scratch)
 {
 	u64 hdr;
 	__le64 *wqe;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	hdr = FIELD_PREP(IRDMA_CQPSQ_SUSPENDQP_QPID, qp->qp_uk.qp_id) |
 	      FIELD_PREP(IRDMA_CQPSQ_OPCODE, IRDMA_CQP_OP_SUSPEND_QP) |
@@ -2456,16 +2405,15 @@
  * @qp: sc qp struct
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code irdma_sc_resume_qp(struct irdma_sc_cqp *cqp,
-						 struct irdma_sc_qp *qp,
-						 u64 scratch)
+static int irdma_sc_resume_qp(struct irdma_sc_cqp *cqp, struct irdma_sc_qp *qp,
+			      u64 scratch)
 {
 	u64 hdr;
 	__le64 *wqe;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16,
 		      FIELD_PREP(IRDMA_CQPSQ_RESUMEQP_QSHANDLE, qp->qs_handle));
@@ -2498,24 +2446,20 @@
  * @cq: cq struct
  * @info: cq initialization info
  */
-enum irdma_status_code irdma_sc_cq_init(struct irdma_sc_cq *cq,
-					struct irdma_cq_init_info *info)
+int irdma_sc_cq_init(struct irdma_sc_cq *cq, struct irdma_cq_init_info *info)
 {
-	enum irdma_status_code ret_code;
 	u32 pble_obj_cnt;
 
 	pble_obj_cnt = info->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_PBLE].cnt;
 	if (info->virtual_map && info->first_pm_pbl_idx >= pble_obj_cnt)
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	cq->cq_pa = info->cq_base_pa;
 	cq->dev = info->dev;
 	cq->ceq_id = info->ceq_id;
 	info->cq_uk_init_info.cqe_alloc_db = cq->dev->cq_arm_db;
 	info->cq_uk_init_info.cq_ack_db = cq->dev->cq_ack_db;
-	ret_code = irdma_uk_cq_init(&cq->cq_uk, &info->cq_uk_init_info);
-	if (ret_code)
-		return ret_code;
+	irdma_uk_cq_init(&cq->cq_uk, &info->cq_uk_init_info);
 
 	cq->virtual_map = info->virtual_map;
 	cq->pbl_chunk_size = info->pbl_chunk_size;
@@ -2539,23 +2483,21 @@
  * @check_overflow: flag for overflow check
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code irdma_sc_cq_create(struct irdma_sc_cq *cq,
-						 u64 scratch,
-						 bool check_overflow,
-						 bool post_sq)
+static int irdma_sc_cq_create(struct irdma_sc_cq *cq, u64 scratch,
+			      bool check_overflow, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
 	u64 hdr;
 	struct irdma_sc_ceq *ceq;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	cqp = cq->dev->cqp;
-	if (cq->cq_uk.cq_id > (cqp->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_CQ].max_cnt - 1))
-		return IRDMA_ERR_INVALID_CQ_ID;
+	if (cq->cq_uk.cq_id >= (cqp->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_CQ].max_cnt))
+		return -EINVAL;
 
-	if (cq->ceq_id > (cq->dev->hmc_fpm_misc.max_ceqs - 1))
-		return IRDMA_ERR_INVALID_CEQ_ID;
+	if (cq->ceq_id >= (cq->dev->hmc_fpm_misc.max_ceqs))
+		return -EINVAL;
 
 	ceq = cq->dev->ceq[cq->ceq_id];
 	if (ceq && ceq->reg_cq)
@@ -2568,7 +2510,7 @@
 	if (!wqe) {
 		if (ceq && ceq->reg_cq)
 			irdma_sc_remove_cq_ctx(ceq, cq);
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	}
 
 	set_64bit_val(wqe, 0, cq->cq_uk.cq_size);
@@ -2614,8 +2556,7 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_cq_destroy(struct irdma_sc_cq *cq, u64 scratch,
-					   bool post_sq)
+int irdma_sc_cq_destroy(struct irdma_sc_cq *cq, u64 scratch, bool post_sq)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
@@ -2625,7 +2566,7 @@
 	cqp = cq->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	ceq = cq->dev->ceq[cq->ceq_id];
 	if (ceq && ceq->reg_cq)
@@ -2681,9 +2622,9 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag to post to sq
  */
-static enum irdma_status_code
-irdma_sc_cq_modify(struct irdma_sc_cq *cq, struct irdma_modify_cq_info *info,
-		   u64 scratch, bool post_sq)
+static int irdma_sc_cq_modify(struct irdma_sc_cq *cq,
+			      struct irdma_modify_cq_info *info, u64 scratch,
+			      bool post_sq)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
@@ -2693,12 +2634,12 @@
 	pble_obj_cnt = cq->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_PBLE].cnt;
 	if (info->cq_resize && info->virtual_map &&
 	    info->first_pm_pbl_idx >= pble_obj_cnt)
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	cqp = cq->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 0, info->cq_size);
 	set_64bit_val(wqe, 8, (uintptr_t)cq >> 1);
@@ -2741,13 +2682,13 @@
  */
 void irdma_check_cqp_progress(struct irdma_cqp_timeout *timeout, struct irdma_sc_dev *dev)
 {
-	if (timeout->compl_cqp_cmds != dev->cqp_cmd_stats[IRDMA_OP_CMPL_CMDS]) {
-		timeout->compl_cqp_cmds = dev->cqp_cmd_stats[IRDMA_OP_CMPL_CMDS];
+	u64 completed_ops = atomic64_read(&dev->cqp->completed_ops);
+
+	if (timeout->compl_cqp_cmds != completed_ops) {
+		timeout->compl_cqp_cmds = completed_ops;
 		timeout->count = 0;
-	} else {
-		if (dev->cqp_cmd_stats[IRDMA_OP_REQ_CMDS] !=
-		    timeout->compl_cqp_cmds)
-			timeout->count++;
+	} else if (timeout->compl_cqp_cmds != dev->cqp->requested_ops) {
+		timeout->count++;
 	}
 }
 
@@ -2772,8 +2713,8 @@
  * @tail: wqtail register value
  * @count: how many times to try for completion
  */
-static enum irdma_status_code irdma_cqp_poll_registers(struct irdma_sc_cqp *cqp,
-						       u32 tail, u32 count)
+static int irdma_cqp_poll_registers(struct irdma_sc_cqp *cqp, u32 tail,
+				    u32 count)
 {
 	u32 i = 0;
 	u32 newtail, error, val;
@@ -2785,18 +2726,18 @@
 			ibdev_dbg(to_ibdev(cqp->dev),
 				  "CQP: CQPERRCODES error_code[x%08X]\n",
 				  error);
-			return IRDMA_ERR_CQP_COMPL_ERROR;
+			return -EIO;
 		}
 		if (newtail != tail) {
 			/* SUCCESS */
 			IRDMA_RING_MOVE_TAIL(cqp->sq_ring);
-			cqp->dev->cqp_cmd_stats[IRDMA_OP_CMPL_CMDS]++;
+			atomic64_inc(&cqp->completed_ops);
 			return 0;
 		}
 		udelay(cqp->dev->hw_attrs.max_sleep_count);
 	}
 
-	return IRDMA_ERR_TIMEOUT;
+	return -ETIMEDOUT;
 }
 
 /**
@@ -2951,10 +2892,9 @@
  * parses fpm query buffer and copy max_cnt and
  * size value of hmc objects in hmc_info
  */
-static enum irdma_status_code
-irdma_sc_parse_fpm_query_buf(struct irdma_sc_dev *dev, __le64 *buf,
-			     struct irdma_hmc_info *hmc_info,
-			     struct irdma_hmc_fpm_misc *hmc_fpm_misc)
+static int irdma_sc_parse_fpm_query_buf(struct irdma_sc_dev *dev, __le64 *buf,
+					struct irdma_hmc_info *hmc_info,
+					struct irdma_hmc_fpm_misc *hmc_fpm_misc)
 {
 	struct irdma_hmc_obj_info *obj_info;
 	u64 temp;
@@ -2993,7 +2933,7 @@
 	obj_info[IRDMA_HMC_IW_XFFL].size = 4;
 	hmc_fpm_misc->xf_block_size = FIELD_GET(IRDMA_QUERY_FPM_XFBLOCKSIZE, temp);
 	if (!hmc_fpm_misc->xf_block_size)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	irdma_sc_decode_fpm_query(buf, 72, obj_info, IRDMA_HMC_IW_Q1);
 	get_64bit_val(buf, 80, &temp);
@@ -3002,7 +2942,7 @@
 
 	hmc_fpm_misc->q1_block_size = FIELD_GET(IRDMA_QUERY_FPM_Q1BLOCKSIZE, temp);
 	if (!hmc_fpm_misc->q1_block_size)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	irdma_sc_decode_fpm_query(buf, 88, obj_info, IRDMA_HMC_IW_TIMER);
 
@@ -3026,7 +2966,7 @@
 	hmc_fpm_misc->rrf_block_size = FIELD_GET(IRDMA_QUERY_FPM_RRFBLOCKSIZE, temp);
 	if (!hmc_fpm_misc->rrf_block_size &&
 	    obj_info[IRDMA_HMC_IW_RRFFL].max_cnt)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	irdma_sc_decode_fpm_query(buf, 144, obj_info, IRDMA_HMC_IW_HDR);
 	irdma_sc_decode_fpm_query(buf, 152, obj_info, IRDMA_HMC_IW_MD);
@@ -3038,7 +2978,7 @@
 	hmc_fpm_misc->ooiscf_block_size = FIELD_GET(IRDMA_QUERY_FPM_OOISCFBLOCKSIZE, temp);
 	if (!hmc_fpm_misc->ooiscf_block_size &&
 	    obj_info[IRDMA_HMC_IW_OOISCFFL].max_cnt)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	return 0;
 }
@@ -3066,8 +3006,7 @@
  * @ceq: ceq sc structure
  * @cq: cq sc structure
  */
-enum irdma_status_code irdma_sc_add_cq_ctx(struct irdma_sc_ceq *ceq,
-					   struct irdma_sc_cq *cq)
+int irdma_sc_add_cq_ctx(struct irdma_sc_ceq *ceq, struct irdma_sc_cq *cq)
 {
 	unsigned long flags;
 
@@ -3075,7 +3014,7 @@
 
 	if (ceq->reg_cq_size == ceq->elem_cnt) {
 		spin_unlock_irqrestore(&ceq->req_cq_lock, flags);
-		return IRDMA_ERR_REG_CQ_FULL;
+		return -ENOMEM;
 	}
 
 	ceq->reg_cq[ceq->reg_cq_size++] = cq;
@@ -3116,15 +3055,15 @@
  *
  * Initializes the object and context buffers for a control Queue Pair.
  */
-enum irdma_status_code irdma_sc_cqp_init(struct irdma_sc_cqp *cqp,
-					 struct irdma_cqp_init_info *info)
+int irdma_sc_cqp_init(struct irdma_sc_cqp *cqp,
+		      struct irdma_cqp_init_info *info)
 {
 	u8 hw_sq_size;
 
 	if (info->sq_size > IRDMA_CQP_SW_SQSIZE_2048 ||
 	    info->sq_size < IRDMA_CQP_SW_SQSIZE_4 ||
 	    ((info->sq_size & (info->sq_size - 1))))
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	hw_sq_size = irdma_get_encoded_wqe_size(info->sq_size,
 						IRDMA_QUEUE_TYPE_CQP);
@@ -3152,8 +3091,8 @@
 	info->dev->cqp = cqp;
 
 	IRDMA_RING_INIT(cqp->sq_ring, cqp->sq_size);
-	cqp->dev->cqp_cmd_stats[IRDMA_OP_REQ_CMDS] = 0;
-	cqp->dev->cqp_cmd_stats[IRDMA_OP_CMPL_CMDS] = 0;
+	cqp->requested_ops = 0;
+	atomic64_set(&cqp->completed_ops, 0);
 	/* for the cqp commands backlog. */
 	INIT_LIST_HEAD(&cqp->dev->cqp_cmd_head);
 
@@ -3174,13 +3113,12 @@
  * @maj_err: If error, major err number
  * @min_err: If error, minor err number
  */
-enum irdma_status_code irdma_sc_cqp_create(struct irdma_sc_cqp *cqp, u16 *maj_err,
-					   u16 *min_err)
+int irdma_sc_cqp_create(struct irdma_sc_cqp *cqp, u16 *maj_err, u16 *min_err)
 {
 	u64 temp;
 	u8 hw_rev;
 	u32 cnt = 0, p1, p2, val = 0, err_code;
-	enum irdma_status_code ret_code;
+	int ret_code;
 
 	hw_rev = cqp->dev->hw_attrs.uk_attrs.hw_rev;
 	cqp->sdbuf.size = ALIGN(IRDMA_UPDATE_SD_BUFF_SIZE * cqp->sq_size,
@@ -3189,7 +3127,7 @@
 					   cqp->sdbuf.size, &cqp->sdbuf.pa,
 					   GFP_KERNEL);
 	if (!cqp->sdbuf.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	spin_lock_init(&cqp->dev->cqp_lock);
 
@@ -3244,7 +3182,7 @@
 
 	do {
 		if (cnt++ > cqp->dev->hw_attrs.max_done_count) {
-			ret_code = IRDMA_ERR_TIMEOUT;
+			ret_code = -ETIMEDOUT;
 			goto err;
 		}
 		udelay(cqp->dev->hw_attrs.max_sleep_count);
@@ -3252,7 +3190,7 @@
 	} while (!val);
 
 	if (FLD_RS_32(cqp->dev, val, IRDMA_CCQPSTATUS_CCQP_ERR)) {
-		ret_code = IRDMA_ERR_DEVICE_NOT_SUPPORTED;
+		ret_code = -EOPNOTSUPP;
 		goto err;
 	}
 
@@ -3293,7 +3231,7 @@
 					   u32 *wqe_idx)
 {
 	__le64 *wqe = NULL;
-	enum irdma_status_code ret_code;
+	int ret_code;
 
 	if (IRDMA_RING_FULL_ERR(cqp->sq_ring)) {
 		ibdev_dbg(to_ibdev(cqp->dev),
@@ -3306,7 +3244,7 @@
 	if (ret_code)
 		return NULL;
 
-	cqp->dev->cqp_cmd_stats[IRDMA_OP_REQ_CMDS]++;
+	cqp->requested_ops++;
 	if (!*wqe_idx)
 		cqp->polarity = !cqp->polarity;
 	wqe = cqp->sq_base[*wqe_idx].elem;
@@ -3320,16 +3258,16 @@
  * irdma_sc_cqp_destroy - destroy cqp during close
  * @cqp: struct for cqp hw
  */
-enum irdma_status_code irdma_sc_cqp_destroy(struct irdma_sc_cqp *cqp)
+int irdma_sc_cqp_destroy(struct irdma_sc_cqp *cqp)
 {
 	u32 cnt = 0, val;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	writel(0, cqp->dev->hw_regs[IRDMA_CCQPHIGH]);
 	writel(0, cqp->dev->hw_regs[IRDMA_CCQPLOW]);
 	do {
 		if (cnt++ > cqp->dev->hw_attrs.max_done_count) {
-			ret_code = IRDMA_ERR_TIMEOUT;
+			ret_code = -ETIMEDOUT;
 			break;
 		}
 		udelay(cqp->dev->hw_attrs.max_sleep_count);
@@ -3374,8 +3312,8 @@
  * @ccq: ccq sc struct
  * @info: completion q entry to return
  */
-enum irdma_status_code irdma_sc_ccq_get_cqe_info(struct irdma_sc_cq *ccq,
-						 struct irdma_ccq_cqe_info *info)
+int irdma_sc_ccq_get_cqe_info(struct irdma_sc_cq *ccq,
+			      struct irdma_ccq_cqe_info *info)
 {
 	u64 qp_ctx, temp, temp1;
 	__le64 *cqe;
@@ -3383,7 +3321,7 @@
 	u32 wqe_idx;
 	u32 error;
 	u8 polarity;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	if (ccq->cq_uk.avoid_mem_cflct)
 		cqe = IRDMA_GET_CURRENT_EXTENDED_CQ_ELEM(&ccq->cq_uk);
@@ -3393,7 +3331,10 @@
 	get_64bit_val(cqe, 24, &temp);
 	polarity = (u8)FIELD_GET(IRDMA_CQ_VALID, temp);
 	if (polarity != ccq->cq_uk.polarity)
-		return IRDMA_ERR_Q_EMPTY;
+		return -ENOENT;
+
+	/* Ensure CEQE contents are read after valid bit is checked */
+	dma_rmb();
 
 	get_64bit_val(cqe, 8, &qp_ctx);
 	cqp = (struct irdma_sc_cqp *)(unsigned long)qp_ctx;
@@ -3429,7 +3370,7 @@
 	dma_wmb(); /* make sure shadow area is updated before moving tail */
 
 	IRDMA_RING_MOVE_TAIL(cqp->sq_ring);
-	ccq->dev->cqp_cmd_stats[IRDMA_OP_CMPL_CMDS]++;
+	atomic64_inc(&cqp->completed_ops);
 
 	return ret_code;
 }
@@ -3440,25 +3381,25 @@
  * @op_code: cqp opcode for completion
  * @compl_info: completion q entry to return
  */
-enum irdma_status_code irdma_sc_poll_for_cqp_op_done(struct irdma_sc_cqp *cqp, u8 op_code,
-						     struct irdma_ccq_cqe_info *compl_info)
+int irdma_sc_poll_for_cqp_op_done(struct irdma_sc_cqp *cqp, u8 op_code,
+				  struct irdma_ccq_cqe_info *compl_info)
 {
 	struct irdma_ccq_cqe_info info = {};
 	struct irdma_sc_cq *ccq;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u32 cnt = 0;
 
 	ccq = cqp->dev->ccq;
 	while (1) {
 		if (cnt++ > 100 * cqp->dev->hw_attrs.max_done_count)
-			return IRDMA_ERR_TIMEOUT;
+			return -ETIMEDOUT;
 
 		if (irdma_sc_ccq_get_cqe_info(ccq, &info)) {
 			udelay(cqp->dev->hw_attrs.max_sleep_count);
 			continue;
 		}
 		if (info.error && info.op_code != IRDMA_CQP_OP_QUERY_STAG) {
-			ret_code = IRDMA_ERR_CQP_COMPL_ERROR;
+			ret_code = -EIO;
 			break;
 		}
 		/* make sure op code matches*/
@@ -3482,17 +3423,16 @@
  * @info: info for the manage function table operation
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code
-irdma_sc_manage_hmc_pm_func_table(struct irdma_sc_cqp *cqp,
-				  struct irdma_hmc_fcn_info *info,
-				  u64 scratch, bool post_sq)
+static int irdma_sc_manage_hmc_pm_func_table(struct irdma_sc_cqp *cqp,
+					     struct irdma_hmc_fcn_info *info,
+					     u64 scratch, bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 0, 0);
 	set_64bit_val(wqe, 8, 0);
@@ -3525,8 +3465,7 @@
  * for fpm commit
  * @cqp: struct for cqp hw
  */
-static enum irdma_status_code
-irdma_sc_commit_fpm_val_done(struct irdma_sc_cqp *cqp)
+static int irdma_sc_commit_fpm_val_done(struct irdma_sc_cqp *cqp)
 {
 	return irdma_sc_poll_for_cqp_op_done(cqp, IRDMA_CQP_OP_COMMIT_FPM_VAL,
 					     NULL);
@@ -3541,19 +3480,19 @@
  * @post_sq: flag for cqp db to ring
  * @wait_type: poll ccq or cqp registers for cqp completion
  */
-static enum irdma_status_code
-irdma_sc_commit_fpm_val(struct irdma_sc_cqp *cqp, u64 scratch, u8 hmc_fn_id,
-			struct irdma_dma_mem *commit_fpm_mem, bool post_sq,
-			u8 wait_type)
+static int irdma_sc_commit_fpm_val(struct irdma_sc_cqp *cqp, u64 scratch,
+				   u8 hmc_fn_id,
+				   struct irdma_dma_mem *commit_fpm_mem,
+				   bool post_sq, u8 wait_type)
 {
 	__le64 *wqe;
 	u64 hdr;
 	u32 tail, val, error;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, hmc_fn_id);
 	set_64bit_val(wqe, 32, commit_fpm_mem->pa);
@@ -3587,8 +3526,7 @@
  * query fpm
  * @cqp: struct for cqp hw
  */
-static enum irdma_status_code
-irdma_sc_query_fpm_val_done(struct irdma_sc_cqp *cqp)
+static int irdma_sc_query_fpm_val_done(struct irdma_sc_cqp *cqp)
 {
 	return irdma_sc_poll_for_cqp_op_done(cqp, IRDMA_CQP_OP_QUERY_FPM_VAL,
 					     NULL);
@@ -3603,19 +3541,19 @@
  * @post_sq: flag for cqp db to ring
  * @wait_type: poll ccq or cqp registers for cqp completion
  */
-static enum irdma_status_code
-irdma_sc_query_fpm_val(struct irdma_sc_cqp *cqp, u64 scratch, u8 hmc_fn_id,
-		       struct irdma_dma_mem *query_fpm_mem, bool post_sq,
-		       u8 wait_type)
+static int irdma_sc_query_fpm_val(struct irdma_sc_cqp *cqp, u64 scratch,
+				  u8 hmc_fn_id,
+				  struct irdma_dma_mem *query_fpm_mem,
+				  bool post_sq, u8 wait_type)
 {
 	__le64 *wqe;
 	u64 hdr;
 	u32 tail, val, error;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, hmc_fn_id);
 	set_64bit_val(wqe, 32, query_fpm_mem->pa);
@@ -3647,21 +3585,21 @@
  * @ceq: ceq sc structure
  * @info: ceq initialization info
  */
-enum irdma_status_code irdma_sc_ceq_init(struct irdma_sc_ceq *ceq,
-					 struct irdma_ceq_init_info *info)
+int irdma_sc_ceq_init(struct irdma_sc_ceq *ceq,
+		      struct irdma_ceq_init_info *info)
 {
 	u32 pble_obj_cnt;
 
 	if (info->elem_cnt < info->dev->hw_attrs.min_hw_ceq_size ||
 	    info->elem_cnt > info->dev->hw_attrs.max_hw_ceq_size)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
-	if (info->ceq_id > (info->dev->hmc_fpm_misc.max_ceqs - 1))
-		return IRDMA_ERR_INVALID_CEQ_ID;
+	if (info->ceq_id >= (info->dev->hmc_fpm_misc.max_ceqs))
+		return -EINVAL;
 	pble_obj_cnt = info->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_PBLE].cnt;
 
 	if (info->virtual_map && info->first_pm_pbl_idx >= pble_obj_cnt)
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	ceq->size = sizeof(*ceq);
 	ceq->ceqe_base = (struct irdma_ceqe *)info->ceqe_base;
@@ -3694,8 +3632,8 @@
  * @post_sq: flag for cqp db to ring
  */
 
-static enum irdma_status_code irdma_sc_ceq_create(struct irdma_sc_ceq *ceq, u64 scratch,
-						  bool post_sq)
+static int irdma_sc_ceq_create(struct irdma_sc_ceq *ceq, u64 scratch,
+			       bool post_sq)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
@@ -3704,7 +3642,7 @@
 	cqp = ceq->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	set_64bit_val(wqe, 16, ceq->elem_cnt);
 	set_64bit_val(wqe, 32,
 		      (ceq->virtual_map ? 0 : ceq->ceq_elem_pa));
@@ -3736,8 +3674,7 @@
  * irdma_sc_cceq_create_done - poll for control ceq wqe to complete
  * @ceq: ceq sc structure
  */
-static enum irdma_status_code
-irdma_sc_cceq_create_done(struct irdma_sc_ceq *ceq)
+static int irdma_sc_cceq_create_done(struct irdma_sc_ceq *ceq)
 {
 	struct irdma_sc_cqp *cqp;
 
@@ -3750,7 +3687,7 @@
  * irdma_sc_cceq_destroy_done - poll for destroy cceq to complete
  * @ceq: ceq sc structure
  */
-enum irdma_status_code irdma_sc_cceq_destroy_done(struct irdma_sc_ceq *ceq)
+int irdma_sc_cceq_destroy_done(struct irdma_sc_ceq *ceq)
 {
 	struct irdma_sc_cqp *cqp;
 
@@ -3769,9 +3706,9 @@
  * @ceq: ceq sc structure
  * @scratch: u64 saved to be used during cqp completion
  */
-enum irdma_status_code irdma_sc_cceq_create(struct irdma_sc_ceq *ceq, u64 scratch)
+int irdma_sc_cceq_create(struct irdma_sc_ceq *ceq, u64 scratch)
 {
-	enum irdma_status_code ret_code;
+	int ret_code;
 	struct irdma_sc_dev *dev = ceq->dev;
 
 	dev->ccq->vsi = ceq->vsi;
@@ -3794,8 +3731,7 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_ceq_destroy(struct irdma_sc_ceq *ceq, u64 scratch,
-					    bool post_sq)
+int irdma_sc_ceq_destroy(struct irdma_sc_ceq *ceq, u64 scratch, bool post_sq)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
@@ -3804,7 +3740,7 @@
 	cqp = ceq->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, ceq->elem_cnt);
 	set_64bit_val(wqe, 48, ceq->first_pm_pbl_idx);
@@ -3923,19 +3859,19 @@
  * @aeq: aeq structure ptr
  * @info: aeq initialization info
  */
-enum irdma_status_code irdma_sc_aeq_init(struct irdma_sc_aeq *aeq,
-					 struct irdma_aeq_init_info *info)
+int irdma_sc_aeq_init(struct irdma_sc_aeq *aeq,
+		      struct irdma_aeq_init_info *info)
 {
 	u32 pble_obj_cnt;
 
 	if (info->elem_cnt < info->dev->hw_attrs.min_hw_aeq_size ||
 	    info->elem_cnt > info->dev->hw_attrs.max_hw_aeq_size)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	pble_obj_cnt = info->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_PBLE].cnt;
 
 	if (info->virtual_map && info->first_pm_pbl_idx >= pble_obj_cnt)
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	aeq->size = sizeof(*aeq);
 	aeq->polarity = 1;
@@ -3960,8 +3896,8 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code irdma_sc_aeq_create(struct irdma_sc_aeq *aeq,
-						  u64 scratch, bool post_sq)
+static int irdma_sc_aeq_create(struct irdma_sc_aeq *aeq, u64 scratch,
+			       bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
@@ -3970,7 +3906,7 @@
 	cqp = aeq->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	set_64bit_val(wqe, 16, aeq->elem_cnt);
 	set_64bit_val(wqe, 32,
 		      (aeq->virtual_map ? 0 : aeq->aeq_elem_pa));
@@ -3999,8 +3935,8 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-static enum irdma_status_code irdma_sc_aeq_destroy(struct irdma_sc_aeq *aeq,
-						   u64 scratch, bool post_sq)
+static int irdma_sc_aeq_destroy(struct irdma_sc_aeq *aeq, u64 scratch,
+				bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
@@ -4013,7 +3949,7 @@
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	set_64bit_val(wqe, 16, aeq->elem_cnt);
 	set_64bit_val(wqe, 48, aeq->first_pm_pbl_idx);
 	hdr = FIELD_PREP(IRDMA_CQPSQ_OPCODE, IRDMA_CQP_OP_DESTROY_AEQ) |
@@ -4036,8 +3972,8 @@
  * @aeq: aeq structure ptr
  * @info: aeqe info to be returned
  */
-enum irdma_status_code irdma_sc_get_next_aeqe(struct irdma_sc_aeq *aeq,
-					      struct irdma_aeqe_info *info)
+int irdma_sc_get_next_aeqe(struct irdma_sc_aeq *aeq,
+			   struct irdma_aeqe_info *info)
 {
 	u64 temp, compl_ctx;
 	__le64 *aeqe;
@@ -4046,12 +3982,16 @@
 	u8 polarity;
 
 	aeqe = IRDMA_GET_CURRENT_AEQ_ELEM(aeq);
-	get_64bit_val(aeqe, 0, &compl_ctx);
 	get_64bit_val(aeqe, 8, &temp);
 	polarity = (u8)FIELD_GET(IRDMA_AEQE_VALID, temp);
 
 	if (aeq->polarity != polarity)
-		return IRDMA_ERR_Q_EMPTY;
+		return -ENOENT;
+
+	/* Ensure AEQE contents are read after valid bit is checked */
+	dma_rmb();
+
+	get_64bit_val(aeqe, 0, &compl_ctx);
 
 	print_hex_dump_debug("WQE: AEQ_ENTRY WQE", DUMP_PREFIX_OFFSET, 16, 8,
 			     aeqe, 16, false);
@@ -4196,22 +4136,21 @@
  * @cq: sc's cq ctruct
  * @info: info for control cq initialization
  */
-enum irdma_status_code irdma_sc_ccq_init(struct irdma_sc_cq *cq,
-					 struct irdma_ccq_init_info *info)
+int irdma_sc_ccq_init(struct irdma_sc_cq *cq, struct irdma_ccq_init_info *info)
 {
 	u32 pble_obj_cnt;
 
 	if (info->num_elem < info->dev->hw_attrs.uk_attrs.min_hw_cq_size ||
 	    info->num_elem > info->dev->hw_attrs.uk_attrs.max_hw_cq_size)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
-	if (info->ceq_id > (info->dev->hmc_fpm_misc.max_ceqs - 1))
-		return IRDMA_ERR_INVALID_CEQ_ID;
+	if (info->ceq_id >= (info->dev->hmc_fpm_misc.max_ceqs ))
+		return -EINVAL;
 
 	pble_obj_cnt = info->dev->hmc_info->hmc_obj[IRDMA_HMC_IW_PBLE].cnt;
 
 	if (info->virtual_map && info->first_pm_pbl_idx >= pble_obj_cnt)
-		return IRDMA_ERR_INVALID_PBLE_INDEX;
+		return -EINVAL;
 
 	cq->cq_pa = info->cq_pa;
 	cq->cq_uk.cq_base = info->cq_base;
@@ -4248,7 +4187,7 @@
  * irdma_sc_ccq_create_done - poll cqp for ccq create
  * @ccq: ccq sc struct
  */
-static inline enum irdma_status_code irdma_sc_ccq_create_done(struct irdma_sc_cq *ccq)
+static inline int irdma_sc_ccq_create_done(struct irdma_sc_cq *ccq)
 {
 	struct irdma_sc_cqp *cqp;
 
@@ -4264,10 +4203,10 @@
  * @check_overflow: overlow flag for ccq
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_ccq_create(struct irdma_sc_cq *ccq, u64 scratch,
-					   bool check_overflow, bool post_sq)
+int irdma_sc_ccq_create(struct irdma_sc_cq *ccq, u64 scratch,
+			bool check_overflow, bool post_sq)
 {
-	enum irdma_status_code ret_code;
+	int ret_code;
 
 	ret_code = irdma_sc_cq_create(ccq, scratch, check_overflow, post_sq);
 	if (ret_code)
@@ -4289,19 +4228,18 @@
  * @scratch: u64 saved to be used during cqp completion
  * @post_sq: flag for cqp db to ring
  */
-enum irdma_status_code irdma_sc_ccq_destroy(struct irdma_sc_cq *ccq, u64 scratch,
-					    bool post_sq)
+int irdma_sc_ccq_destroy(struct irdma_sc_cq *ccq, u64 scratch, bool post_sq)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
 	u64 hdr;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u32 tail, val, error;
 
 	cqp = ccq->dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 0, ccq->cq_uk.cq_size);
 	set_64bit_val(wqe, 8, (uintptr_t)ccq >> 1);
@@ -4340,13 +4278,12 @@
  * @dev : ptr to irdma_dev struct
  * @hmc_fn_id: hmc function id
  */
-enum irdma_status_code irdma_sc_init_iw_hmc(struct irdma_sc_dev *dev,
-					    u8 hmc_fn_id)
+int irdma_sc_init_iw_hmc(struct irdma_sc_dev *dev, u8 hmc_fn_id)
 {
 	struct irdma_hmc_info *hmc_info;
 	struct irdma_hmc_fpm_misc *hmc_fpm_misc;
 	struct irdma_dma_mem query_fpm_mem;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u8 wait_type;
 
 	hmc_info = dev->hmc_info;
@@ -4377,14 +4314,13 @@
  * @dev : ptr to irdma_dev struct
  * @hmc_fn_id: hmc function id
  */
-static enum irdma_status_code irdma_sc_cfg_iw_fpm(struct irdma_sc_dev *dev,
-						  u8 hmc_fn_id)
+static int irdma_sc_cfg_iw_fpm(struct irdma_sc_dev *dev, u8 hmc_fn_id)
 {
 	struct irdma_hmc_info *hmc_info;
 	struct irdma_hmc_obj_info *obj_info;
 	__le64 *buf;
 	struct irdma_dma_mem commit_fpm_mem;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u8 wait_type;
 
 	hmc_info = dev->hmc_info;
@@ -4447,9 +4383,8 @@
  * @info: sd info for wqe
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code
-cqp_sds_wqe_fill(struct irdma_sc_cqp *cqp, struct irdma_update_sds_info *info,
-		 u64 scratch)
+static int cqp_sds_wqe_fill(struct irdma_sc_cqp *cqp,
+			    struct irdma_update_sds_info *info, u64 scratch)
 {
 	u64 data;
 	u64 hdr;
@@ -4461,7 +4396,7 @@
 
 	wqe = irdma_sc_cqp_get_next_send_wqe_idx(cqp, scratch, &wqe_idx);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	wqe_entries = (info->cnt > 3) ? 3 : info->cnt;
 	mem_entries = info->cnt - wqe_entries;
@@ -4527,12 +4462,11 @@
  * @info: sd info for sd's
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code
-irdma_update_pe_sds(struct irdma_sc_dev *dev,
-		    struct irdma_update_sds_info *info, u64 scratch)
+static int irdma_update_pe_sds(struct irdma_sc_dev *dev,
+			       struct irdma_update_sds_info *info, u64 scratch)
 {
 	struct irdma_sc_cqp *cqp = dev->cqp;
-	enum irdma_status_code ret_code;
+	int ret_code;
 
 	ret_code = cqp_sds_wqe_fill(cqp, info, scratch);
 	if (!ret_code)
@@ -4546,13 +4480,12 @@
  * @dev: sc device struct
  * @info: sd info for sd's
  */
-enum irdma_status_code
-irdma_update_sds_noccq(struct irdma_sc_dev *dev,
-		       struct irdma_update_sds_info *info)
+int irdma_update_sds_noccq(struct irdma_sc_dev *dev,
+			   struct irdma_update_sds_info *info)
 {
 	u32 error, val, tail;
 	struct irdma_sc_cqp *cqp = dev->cqp;
-	enum irdma_status_code ret_code;
+	int ret_code;
 
 	ret_code = cqp_sds_wqe_fill(cqp, info, 0);
 	if (ret_code)
@@ -4573,10 +4506,9 @@
  * @post_sq: flag for cqp db to ring
  * @poll_registers: flag to poll register for cqp completion
  */
-enum irdma_status_code
-irdma_sc_static_hmc_pages_allocated(struct irdma_sc_cqp *cqp, u64 scratch,
-				    u8 hmc_fn_id, bool post_sq,
-				    bool poll_registers)
+int irdma_sc_static_hmc_pages_allocated(struct irdma_sc_cqp *cqp, u64 scratch,
+					u8 hmc_fn_id, bool post_sq,
+					bool poll_registers)
 {
 	u64 hdr;
 	__le64 *wqe;
@@ -4584,7 +4516,7 @@
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16,
 		      FIELD_PREP(IRDMA_SHMC_PAGE_ALLOCATED_HMC_FN_ID, hmc_fn_id));
@@ -4659,8 +4591,7 @@
  * irdma_sc_query_rdma_features_done - poll cqp for query features done
  * @cqp: struct for cqp hw
  */
-static enum irdma_status_code
-irdma_sc_query_rdma_features_done(struct irdma_sc_cqp *cqp)
+static int irdma_sc_query_rdma_features_done(struct irdma_sc_cqp *cqp)
 {
 	return irdma_sc_poll_for_cqp_op_done(cqp,
 					     IRDMA_CQP_OP_QUERY_RDMA_FEATURES,
@@ -4673,16 +4604,15 @@
  * @buf: buffer to hold query info
  * @scratch: u64 saved to be used during cqp completion
  */
-static enum irdma_status_code
-irdma_sc_query_rdma_features(struct irdma_sc_cqp *cqp,
-			     struct irdma_dma_mem *buf, u64 scratch)
+static int irdma_sc_query_rdma_features(struct irdma_sc_cqp *cqp,
+					struct irdma_dma_mem *buf, u64 scratch)
 {
 	__le64 *wqe;
 	u64 temp;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	temp = buf->pa;
 	set_64bit_val(wqe, 32, temp);
@@ -4706,9 +4636,9 @@
  * irdma_get_rdma_features - get RDMA features
  * @dev: sc device struct
  */
-enum irdma_status_code irdma_get_rdma_features(struct irdma_sc_dev *dev)
+int irdma_get_rdma_features(struct irdma_sc_dev *dev)
 {
-	enum irdma_status_code ret_code;
+	int ret_code;
 	struct irdma_dma_mem feat_buf;
 	u64 temp;
 	u16 byte_idx, feat_type, feat_cnt, feat_idx;
@@ -4718,7 +4648,7 @@
 	feat_buf.va = dma_alloc_coherent(dev->hw->device, feat_buf.size,
 					 &feat_buf.pa, GFP_KERNEL);
 	if (!feat_buf.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	ret_code = irdma_sc_query_rdma_features(dev->cqp, &feat_buf, 0);
 	if (!ret_code)
@@ -4729,7 +4659,7 @@
 	get_64bit_val(feat_buf.va, 0, &temp);
 	feat_cnt = (u16)FIELD_GET(IRDMA_FEATURE_CNT, temp);
 	if (feat_cnt < 2) {
-		ret_code = IRDMA_ERR_INVALID_FEAT_CNT;
+		ret_code = -EINVAL;
 		goto exit;
 	} else if (feat_cnt > IRDMA_MAX_FEATURES) {
 		ibdev_dbg(to_ibdev(dev),
@@ -4743,7 +4673,7 @@
 						 feat_buf.size, &feat_buf.pa,
 						 GFP_KERNEL);
 		if (!feat_buf.va)
-			return IRDMA_ERR_NO_MEMORY;
+			return -ENOMEM;
 
 		ret_code = irdma_sc_query_rdma_features(dev->cqp, &feat_buf, 0);
 		if (!ret_code)
@@ -4754,7 +4684,7 @@
 		get_64bit_val(feat_buf.va, 0, &temp);
 		feat_cnt = (u16)FIELD_GET(IRDMA_FEATURE_CNT, temp);
 		if (feat_cnt < 2) {
-			ret_code = IRDMA_ERR_INVALID_FEAT_CNT;
+			ret_code = -EINVAL;
 			goto exit;
 		}
 	}
@@ -4833,7 +4763,7 @@
  * @dev: sc device struct
  * @qp_count: desired qp count
  */
-enum irdma_status_code irdma_cfg_fpm_val(struct irdma_sc_dev *dev, u32 qp_count)
+int irdma_cfg_fpm_val(struct irdma_sc_dev *dev, u32 qp_count)
 {
 	struct irdma_virt_mem virt_mem;
 	u32 i, mem_size;
@@ -4844,7 +4774,7 @@
 	u32 loop_count = 0;
 	struct irdma_hmc_info *hmc_info;
 	struct irdma_hmc_fpm_misc *hmc_fpm_misc;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	hmc_info = dev->hmc_info;
 	hmc_fpm_misc = &dev->hmc_fpm_misc;
@@ -4971,7 +4901,7 @@
 		ibdev_dbg(to_ibdev(dev),
 			  "HMC: cfg_fpm failed loop_cnt=%d, sd_needed=%d, max sd count %d\n",
 			  loop_count, sd_needed, hmc_info->sd_table.sd_cnt);
-		return IRDMA_ERR_CFG;
+		return -EINVAL;
 	}
 
 	if (loop_count > 1 && sd_needed < hmc_fpm_misc->max_sds) {
@@ -5007,7 +4937,7 @@
 	if (!virt_mem.va) {
 		ibdev_dbg(to_ibdev(dev),
 			  "HMC: failed to allocate memory for sd_entry buffer\n");
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 	hmc_info->sd_table.sd_entry = virt_mem.va;
 
@@ -5019,10 +4949,10 @@
  * @dev: rdma device
  * @pcmdinfo: cqp command info
  */
-static enum irdma_status_code irdma_exec_cqp_cmd(struct irdma_sc_dev *dev,
-						 struct cqp_cmds_info *pcmdinfo)
+static int irdma_exec_cqp_cmd(struct irdma_sc_dev *dev,
+			      struct cqp_cmds_info *pcmdinfo)
 {
-	enum irdma_status_code status;
+	int status;
 	struct irdma_dma_mem val_mem;
 	bool alloc = false;
 
@@ -5284,7 +5214,7 @@
 						   pcmdinfo->in.u.mc_modify.scratch);
 		break;
 	default:
-		status = IRDMA_NOT_SUPPORTED;
+		status = -EOPNOTSUPP;
 		break;
 	}
 
@@ -5296,10 +5226,10 @@
  * @dev: sc device struct
  * @pcmdinfo: cqp command info
  */
-enum irdma_status_code irdma_process_cqp_cmd(struct irdma_sc_dev *dev,
-					     struct cqp_cmds_info *pcmdinfo)
+int irdma_process_cqp_cmd(struct irdma_sc_dev *dev,
+			  struct cqp_cmds_info *pcmdinfo)
 {
-	enum irdma_status_code status = 0;
+	int status = 0;
 	unsigned long flags;
 
 	spin_lock_irqsave(&dev->cqp_lock, flags);
@@ -5315,9 +5245,9 @@
  * irdma_process_bh - called from tasklet for cqp list
  * @dev: sc device struct
  */
-enum irdma_status_code irdma_process_bh(struct irdma_sc_dev *dev)
+int irdma_process_bh(struct irdma_sc_dev *dev)
 {
-	enum irdma_status_code status = 0;
+	int status = 0;
 	struct cqp_cmds_info *pcmdinfo;
 	unsigned long flags;
 
@@ -5405,12 +5335,11 @@
  * @dev: Device pointer
  * @info: Device init info
  */
-enum irdma_status_code irdma_sc_dev_init(enum irdma_vers ver,
-					 struct irdma_sc_dev *dev,
-					 struct irdma_device_init_info *info)
+int irdma_sc_dev_init(enum irdma_vers ver, struct irdma_sc_dev *dev,
+		      struct irdma_device_init_info *info)
 {
 	u32 val;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u8 db_size;
 
 	INIT_LIST_HEAD(&dev->cqp_cmd_head); /* for CQP command backlog */
@@ -5454,7 +5383,7 @@
 	irdma_sc_init_hw(dev);
 
 	if (irdma_wait_pe_ready(dev))
-		return IRDMA_ERR_TIMEOUT;
+		return -ETIMEDOUT;
 
 	val = readl(dev->hw_regs[IRDMA_GLPCI_LBARCTRL]);
 	db_size = (u8)FIELD_GET(IRDMA_GLPCI_LBARCTRL_PE_DB_SIZE, val);
@@ -5462,7 +5391,7 @@
 		ibdev_dbg(to_ibdev(dev),
 			  "DEV: RDMA PE doorbell is not enabled in CSR val 0x%x db_size=%d\n",
 			  val, db_size);
-		return IRDMA_ERR_PE_DOORBELL_NOT_ENA;
+		return -ENODEV;
 	}
 	dev->db_addr = dev->hw->hw_addr + (uintptr_t)dev->hw_regs[IRDMA_DB_ADDR_OFFSET];
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/defs.h
@@ -190,32 +190,30 @@
 	IRDMA_OP_MANAGE_VF_PBLE_BP		= 25,
 	IRDMA_OP_QUERY_FPM_VAL			= 26,
 	IRDMA_OP_COMMIT_FPM_VAL			= 27,
-	IRDMA_OP_REQ_CMDS			= 28,
-	IRDMA_OP_CMPL_CMDS			= 29,
-	IRDMA_OP_AH_CREATE			= 30,
-	IRDMA_OP_AH_MODIFY			= 31,
-	IRDMA_OP_AH_DESTROY			= 32,
-	IRDMA_OP_MC_CREATE			= 33,
-	IRDMA_OP_MC_DESTROY			= 34,
-	IRDMA_OP_MC_MODIFY			= 35,
-	IRDMA_OP_STATS_ALLOCATE			= 36,
-	IRDMA_OP_STATS_FREE			= 37,
-	IRDMA_OP_STATS_GATHER			= 38,
-	IRDMA_OP_WS_ADD_NODE			= 39,
-	IRDMA_OP_WS_MODIFY_NODE			= 40,
-	IRDMA_OP_WS_DELETE_NODE			= 41,
-	IRDMA_OP_WS_FAILOVER_START		= 42,
-	IRDMA_OP_WS_FAILOVER_COMPLETE		= 43,
-	IRDMA_OP_SET_UP_MAP			= 44,
-	IRDMA_OP_GEN_AE				= 45,
-	IRDMA_OP_QUERY_RDMA_FEATURES		= 46,
-	IRDMA_OP_ALLOC_LOCAL_MAC_ENTRY		= 47,
-	IRDMA_OP_ADD_LOCAL_MAC_ENTRY		= 48,
-	IRDMA_OP_DELETE_LOCAL_MAC_ENTRY		= 49,
-	IRDMA_OP_CQ_MODIFY			= 50,
+	IRDMA_OP_AH_CREATE			= 28,
+	IRDMA_OP_AH_MODIFY			= 29,
+	IRDMA_OP_AH_DESTROY			= 30,
+	IRDMA_OP_MC_CREATE			= 31,
+	IRDMA_OP_MC_DESTROY			= 32,
+	IRDMA_OP_MC_MODIFY			= 33,
+	IRDMA_OP_STATS_ALLOCATE			= 34,
+	IRDMA_OP_STATS_FREE			= 35,
+	IRDMA_OP_STATS_GATHER			= 36,
+	IRDMA_OP_WS_ADD_NODE			= 37,
+	IRDMA_OP_WS_MODIFY_NODE			= 38,
+	IRDMA_OP_WS_DELETE_NODE			= 39,
+	IRDMA_OP_WS_FAILOVER_START		= 40,
+	IRDMA_OP_WS_FAILOVER_COMPLETE		= 41,
+	IRDMA_OP_SET_UP_MAP			= 42,
+	IRDMA_OP_GEN_AE				= 43,
+	IRDMA_OP_QUERY_RDMA_FEATURES		= 44,
+	IRDMA_OP_ALLOC_LOCAL_MAC_ENTRY		= 45,
+	IRDMA_OP_ADD_LOCAL_MAC_ENTRY		= 46,
+	IRDMA_OP_DELETE_LOCAL_MAC_ENTRY		= 47,
+	IRDMA_OP_CQ_MODIFY			= 48,
 
 	/* Must be last entry*/
-	IRDMA_MAX_CQP_OPS			= 51,
+	IRDMA_MAX_CQP_OPS			= 49,
 };
 
 /* CQP SQ WQES */
@@ -314,6 +312,7 @@
 #define IRDMA_AE_IB_REMOTE_ACCESS_ERROR					0x020d
 #define IRDMA_AE_IB_REMOTE_OP_ERROR					0x020e
 #define IRDMA_AE_WQE_LSMM_TOO_LONG					0x0220
+#define IRDMA_AE_INVALID_REQUEST					0x0223
 #define IRDMA_AE_DDP_INVALID_MSN_GAP_IN_MSN				0x0301
 #define IRDMA_AE_DDP_UBE_DDP_MESSAGE_TOO_LONG_FOR_AVAILABLE_BUFFER	0x0303
 #define IRDMA_AE_DDP_UBE_INVALID_DDP_VERSION				0x0304
@@ -346,6 +345,7 @@
 #define IRDMA_AE_LLP_TOO_MANY_KEEPALIVE_RETRIES				0x050b
 #define IRDMA_AE_LLP_DOUBT_REACHABILITY					0x050c
 #define IRDMA_AE_LLP_CONNECTION_ESTABLISHED				0x050e
+#define IRDMA_AE_LLP_TOO_MANY_RNRS					0x050f
 #define IRDMA_AE_RESOURCE_EXHAUSTION					0x0520
 #define IRDMA_AE_RESET_SENT						0x0601
 #define IRDMA_AE_TERMINATE_SENT						0x0602
@@ -964,7 +964,7 @@
 			(_ring).head = ((_ring).head + 1) % size; \
 			(_retcode) = 0; \
 		} else { \
-			(_retcode) = IRDMA_ERR_RING_FULL; \
+			(_retcode) = -ENOMEM; \
 		} \
 	}
 #define IRDMA_RING_MOVE_HEAD_BY_COUNT(_ring, _count, _retcode) \
@@ -975,7 +975,7 @@
 			(_ring).head = ((_ring).head + (_count)) % size; \
 			(_retcode) = 0; \
 		} else { \
-			(_retcode) = IRDMA_ERR_RING_FULL; \
+			(_retcode) = -ENOMEM; \
 		} \
 	}
 #define IRDMA_SQ_RING_MOVE_HEAD(_ring, _retcode) \
@@ -986,7 +986,7 @@
 			(_ring).head = ((_ring).head + 1) % size; \
 			(_retcode) = 0; \
 		} else { \
-			(_retcode) = IRDMA_ERR_RING_FULL; \
+			(_retcode) = -ENOMEM; \
 		} \
 	}
 #define IRDMA_SQ_RING_MOVE_HEAD_BY_COUNT(_ring, _count, _retcode) \
@@ -997,7 +997,7 @@
 			(_ring).head = ((_ring).head + (_count)) % size; \
 			(_retcode) = 0; \
 		} else { \
-			(_retcode) = IRDMA_ERR_RING_FULL; \
+			(_retcode) = -ENOMEM; \
 		} \
 	}
 #define IRDMA_RING_MOVE_HEAD_BY_COUNT_NOCHECK(_ring, _count) \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/hmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/hmc.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2015 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "hmc.h"
 #include "defs.h"
 #include "type.h"
@@ -121,10 +120,8 @@
  * @type: paged or direct sd
  * @setsd: flag to set or clear sd
  */
-enum irdma_status_code irdma_hmc_sd_one(struct irdma_sc_dev *dev, u8 hmc_fn_id,
-					u64 pa, u32 sd_idx,
-					enum irdma_sd_entry_type type,
-					bool setsd)
+int irdma_hmc_sd_one(struct irdma_sc_dev *dev, u8 hmc_fn_id, u64 pa, u32 sd_idx,
+		     enum irdma_sd_entry_type type, bool setsd)
 {
 	struct irdma_update_sds_info sdinfo;
 
@@ -145,16 +142,15 @@
  * @sd_cnt: number of sd entries
  * @setsd: flag to set or clear sd
  */
-static enum irdma_status_code irdma_hmc_sd_grp(struct irdma_sc_dev *dev,
-					       struct irdma_hmc_info *hmc_info,
-					       u32 sd_index, u32 sd_cnt,
-					       bool setsd)
+static int irdma_hmc_sd_grp(struct irdma_sc_dev *dev,
+			    struct irdma_hmc_info *hmc_info, u32 sd_index,
+			    u32 sd_cnt, bool setsd)
 {
 	struct irdma_hmc_sd_entry *sd_entry;
 	struct irdma_update_sds_info sdinfo = {};
 	u64 pa;
 	u32 i;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	sdinfo.hmc_fn_id = hmc_info->hmc_fn_id;
 	for (i = sd_index; i < sd_index + sd_cnt; i++) {
@@ -196,16 +192,15 @@
  * @dev: pointer to the device structure
  * @info: create obj info
  */
-static enum irdma_status_code
-irdma_hmc_finish_add_sd_reg(struct irdma_sc_dev *dev,
-			    struct irdma_hmc_create_obj_info *info)
+static int irdma_hmc_finish_add_sd_reg(struct irdma_sc_dev *dev,
+				       struct irdma_hmc_create_obj_info *info)
 {
 	if (info->start_idx >= info->hmc_info->hmc_obj[info->rsrc_type].cnt)
-		return IRDMA_ERR_INVALID_HMC_OBJ_INDEX;
+		return -EINVAL;
 
 	if ((info->start_idx + info->count) >
 	    info->hmc_info->hmc_obj[info->rsrc_type].cnt)
-		return IRDMA_ERR_INVALID_HMC_OBJ_COUNT;
+		return -EINVAL;
 
 	if (!info->add_sd_cnt)
 		return 0;
@@ -222,9 +217,8 @@
  * This will allocate memory for PDs and backing pages and populate
  * the sd and pd entries.
  */
-enum irdma_status_code
-irdma_sc_create_hmc_obj(struct irdma_sc_dev *dev,
-			struct irdma_hmc_create_obj_info *info)
+int irdma_sc_create_hmc_obj(struct irdma_sc_dev *dev,
+			    struct irdma_hmc_create_obj_info *info)
 {
 	struct irdma_hmc_sd_entry *sd_entry;
 	u32 sd_idx, sd_lmt;
@@ -232,10 +226,10 @@
 	u32 pd_idx1 = 0, pd_lmt1 = 0;
 	u32 i, j;
 	bool pd_error = false;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	if (info->start_idx >= info->hmc_info->hmc_obj[info->rsrc_type].cnt)
-		return IRDMA_ERR_INVALID_HMC_OBJ_INDEX;
+		return -EINVAL;
 
 	if ((info->start_idx + info->count) >
 	    info->hmc_info->hmc_obj[info->rsrc_type].cnt) {
@@ -243,7 +237,7 @@
 			  "HMC: error type %u, start = %u, req cnt %u, cnt = %u\n",
 			  info->rsrc_type, info->start_idx, info->count,
 			  info->hmc_info->hmc_obj[info->rsrc_type].cnt);
-		return IRDMA_ERR_INVALID_HMC_OBJ_COUNT;
+		return -EINVAL;
 	}
 
 	irdma_find_sd_index_limit(info->hmc_info, info->rsrc_type,
@@ -251,7 +245,7 @@
 				  &sd_lmt);
 	if (sd_idx >= info->hmc_info->sd_table.sd_cnt ||
 	    sd_lmt > info->hmc_info->sd_table.sd_cnt) {
-		return IRDMA_ERR_INVALID_SD_INDEX;
+		return -EINVAL;
 	}
 
 	irdma_find_pd_index_limit(info->hmc_info, info->rsrc_type,
@@ -312,7 +306,7 @@
 			irdma_prep_remove_pd_page(info->hmc_info, (j - 1));
 			break;
 		default:
-			ret_code = IRDMA_ERR_INVALID_SD_TYPE;
+			ret_code = -EINVAL;
 			break;
 		}
 		j--;
@@ -327,12 +321,12 @@
  * @info: dele obj info
  * @reset: true if called before reset
  */
-static enum irdma_status_code
-irdma_finish_del_sd_reg(struct irdma_sc_dev *dev,
-			struct irdma_hmc_del_obj_info *info, bool reset)
+static int irdma_finish_del_sd_reg(struct irdma_sc_dev *dev,
+				   struct irdma_hmc_del_obj_info *info,
+				   bool reset)
 {
 	struct irdma_hmc_sd_entry *sd_entry;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u32 i, sd_idx;
 	struct irdma_dma_mem *mem;
 
@@ -373,22 +367,21 @@
  * caller should deallocate memory allocated previously for
  * book-keeping information about PDs and backing storage.
  */
-enum irdma_status_code irdma_sc_del_hmc_obj(struct irdma_sc_dev *dev,
-					    struct irdma_hmc_del_obj_info *info,
-					    bool reset)
+int irdma_sc_del_hmc_obj(struct irdma_sc_dev *dev,
+			 struct irdma_hmc_del_obj_info *info, bool reset)
 {
 	struct irdma_hmc_pd_table *pd_table;
 	u32 sd_idx, sd_lmt;
 	u32 pd_idx, pd_lmt, rel_pd_idx;
 	u32 i, j;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	if (info->start_idx >= info->hmc_info->hmc_obj[info->rsrc_type].cnt) {
 		ibdev_dbg(to_ibdev(dev),
 			  "HMC: error start_idx[%04d]  >= [type %04d].cnt[%04d]\n",
 			  info->start_idx, info->rsrc_type,
 			  info->hmc_info->hmc_obj[info->rsrc_type].cnt);
-		return IRDMA_ERR_INVALID_HMC_OBJ_INDEX;
+		return -EINVAL;
 	}
 
 	if ((info->start_idx + info->count) >
@@ -397,7 +390,7 @@
 			  "HMC: error start_idx[%04d] + count %04d  >= [type %04d].cnt[%04d]\n",
 			  info->start_idx, info->count, info->rsrc_type,
 			  info->hmc_info->hmc_obj[info->rsrc_type].cnt);
-		return IRDMA_ERR_INVALID_HMC_OBJ_COUNT;
+		return -EINVAL;
 	}
 
 	irdma_find_pd_index_limit(info->hmc_info, info->rsrc_type,
@@ -433,7 +426,7 @@
 	if (sd_idx >= info->hmc_info->sd_table.sd_cnt ||
 	    sd_lmt > info->hmc_info->sd_table.sd_cnt) {
 		ibdev_dbg(to_ibdev(dev), "HMC: invalid sd_idx\n");
-		return IRDMA_ERR_INVALID_SD_INDEX;
+		return -EINVAL;
 	}
 
 	for (i = sd_idx; i < sd_lmt; i++) {
@@ -477,11 +470,9 @@
  * @type: what type of segment descriptor we're manipulating
  * @direct_mode_sz: size to alloc in direct mode
  */
-enum irdma_status_code irdma_add_sd_table_entry(struct irdma_hw *hw,
-						struct irdma_hmc_info *hmc_info,
-						u32 sd_index,
-						enum irdma_sd_entry_type type,
-						u64 direct_mode_sz)
+int irdma_add_sd_table_entry(struct irdma_hw *hw,
+			     struct irdma_hmc_info *hmc_info, u32 sd_index,
+			     enum irdma_sd_entry_type type, u64 direct_mode_sz)
 {
 	struct irdma_hmc_sd_entry *sd_entry;
 	struct irdma_dma_mem dma_mem;
@@ -499,7 +490,7 @@
 		dma_mem.va = dma_alloc_coherent(hw->device, dma_mem.size,
 						&dma_mem.pa, GFP_KERNEL);
 		if (!dma_mem.va)
-			return IRDMA_ERR_NO_MEMORY;
+			return -ENOMEM;
 		if (type == IRDMA_SD_TYPE_PAGED) {
 			struct irdma_virt_mem *vmem =
 				&sd_entry->u.pd_table.pd_entry_virt_mem;
@@ -510,7 +501,7 @@
 				dma_free_coherent(hw->device, dma_mem.size,
 						  dma_mem.va, dma_mem.pa);
 				dma_mem.va = NULL;
-				return IRDMA_ERR_NO_MEMORY;
+				return -ENOMEM;
 			}
 			sd_entry->u.pd_table.pd_entry = vmem->va;
 
@@ -549,10 +540,9 @@
  *	   aligned on 4K boundary and zeroed memory.
  *	2. It should be 4K in size.
  */
-enum irdma_status_code irdma_add_pd_table_entry(struct irdma_sc_dev *dev,
-						struct irdma_hmc_info *hmc_info,
-						u32 pd_index,
-						struct irdma_dma_mem *rsrc_pg)
+int irdma_add_pd_table_entry(struct irdma_sc_dev *dev,
+			     struct irdma_hmc_info *hmc_info, u32 pd_index,
+			     struct irdma_dma_mem *rsrc_pg)
 {
 	struct irdma_hmc_pd_table *pd_table;
 	struct irdma_hmc_pd_entry *pd_entry;
@@ -563,7 +553,7 @@
 	u64 page_desc;
 
 	if (pd_index / IRDMA_HMC_PD_CNT_IN_SD >= hmc_info->sd_table.sd_cnt)
-		return IRDMA_ERR_INVALID_PAGE_DESC_INDEX;
+		return -EINVAL;
 
 	sd_idx = (pd_index / IRDMA_HMC_PD_CNT_IN_SD);
 	if (hmc_info->sd_table.sd_entry[sd_idx].entry_type !=
@@ -584,7 +574,7 @@
 						      page->size, &page->pa,
 						      GFP_KERNEL);
 			if (!page->va)
-				return IRDMA_ERR_NO_MEMORY;
+				return -ENOMEM;
 
 			pd_entry->rsrc_pg = false;
 		}
@@ -621,9 +611,8 @@
  *	1. Caller can deallocate the memory used by backing storage after this
  *	   function returns.
  */
-enum irdma_status_code irdma_remove_pd_bp(struct irdma_sc_dev *dev,
-					  struct irdma_hmc_info *hmc_info,
-					  u32 idx)
+int irdma_remove_pd_bp(struct irdma_sc_dev *dev,
+		       struct irdma_hmc_info *hmc_info, u32 idx)
 {
 	struct irdma_hmc_pd_entry *pd_entry;
 	struct irdma_hmc_pd_table *pd_table;
@@ -635,11 +624,11 @@
 	sd_idx = idx / IRDMA_HMC_PD_CNT_IN_SD;
 	rel_pd_idx = idx % IRDMA_HMC_PD_CNT_IN_SD;
 	if (sd_idx >= hmc_info->sd_table.sd_cnt)
-		return IRDMA_ERR_INVALID_PAGE_DESC_INDEX;
+		return -EINVAL;
 
 	sd_entry = &hmc_info->sd_table.sd_entry[sd_idx];
 	if (sd_entry->entry_type != IRDMA_SD_TYPE_PAGED)
-		return IRDMA_ERR_INVALID_SD_TYPE;
+		return -EINVAL;
 
 	pd_table = &hmc_info->sd_table.sd_entry[sd_idx].u.pd_table;
 	pd_entry = &pd_table->pd_entry[rel_pd_idx];
@@ -656,7 +645,7 @@
 	if (!pd_entry->rsrc_pg) {
 		mem = &pd_entry->bp.addr;
 		if (!mem || !mem->va)
-			return IRDMA_ERR_PARAM;
+			return -EINVAL;
 
 		dma_free_coherent(dev->hw->device, mem->size, mem->va,
 				  mem->pa);
@@ -673,14 +662,13 @@
  * @hmc_info: pointer to the HMC configuration information structure
  * @idx: the page index
  */
-enum irdma_status_code irdma_prep_remove_sd_bp(struct irdma_hmc_info *hmc_info,
-					       u32 idx)
+int irdma_prep_remove_sd_bp(struct irdma_hmc_info *hmc_info, u32 idx)
 {
 	struct irdma_hmc_sd_entry *sd_entry;
 
 	sd_entry = &hmc_info->sd_table.sd_entry[idx];
 	if (--sd_entry->u.bp.use_cnt)
-		return IRDMA_ERR_NOT_READY;
+		return -EBUSY;
 
 	hmc_info->sd_table.use_cnt--;
 	sd_entry->valid = false;
@@ -693,15 +681,14 @@
  * @hmc_info: pointer to the HMC configuration information structure
  * @idx: segment descriptor index to find the relevant page descriptor
  */
-enum irdma_status_code
-irdma_prep_remove_pd_page(struct irdma_hmc_info *hmc_info, u32 idx)
+int irdma_prep_remove_pd_page(struct irdma_hmc_info *hmc_info, u32 idx)
 {
 	struct irdma_hmc_sd_entry *sd_entry;
 
 	sd_entry = &hmc_info->sd_table.sd_entry[idx];
 
 	if (sd_entry->u.pd_table.use_cnt)
-		return IRDMA_ERR_NOT_READY;
+		return -EBUSY;
 
 	sd_entry->valid = false;
 	hmc_info->sd_table.use_cnt--;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/hmc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/hmc.h
@@ -141,40 +141,29 @@
 	bool privileged;
 };
 
-enum irdma_status_code irdma_copy_dma_mem(struct irdma_hw *hw, void *dest_buf,
-					  struct irdma_dma_mem *src_mem,
-					  u64 src_offset, u64 size);
-enum irdma_status_code
-irdma_sc_create_hmc_obj(struct irdma_sc_dev *dev,
-			struct irdma_hmc_create_obj_info *info);
-enum irdma_status_code irdma_sc_del_hmc_obj(struct irdma_sc_dev *dev,
-					    struct irdma_hmc_del_obj_info *info,
-					    bool reset);
-enum irdma_status_code irdma_hmc_sd_one(struct irdma_sc_dev *dev, u8 hmc_fn_id,
-					u64 pa, u32 sd_idx,
-					enum irdma_sd_entry_type type,
-					bool setsd);
-enum irdma_status_code
-irdma_update_sds_noccq(struct irdma_sc_dev *dev,
-		       struct irdma_update_sds_info *info);
+int irdma_copy_dma_mem(struct irdma_hw *hw, void *dest_buf,
+		       struct irdma_dma_mem *src_mem, u64 src_offset, u64 size);
+int irdma_sc_create_hmc_obj(struct irdma_sc_dev *dev,
+			    struct irdma_hmc_create_obj_info *info);
+int irdma_sc_del_hmc_obj(struct irdma_sc_dev *dev,
+			 struct irdma_hmc_del_obj_info *info, bool reset);
+int irdma_hmc_sd_one(struct irdma_sc_dev *dev, u8 hmc_fn_id, u64 pa, u32 sd_idx,
+		     enum irdma_sd_entry_type type,
+		     bool setsd);
+int irdma_update_sds_noccq(struct irdma_sc_dev *dev,
+			   struct irdma_update_sds_info *info);
 struct irdma_vfdev *irdma_vfdev_from_fpm(struct irdma_sc_dev *dev,
 					 u8 hmc_fn_id);
 struct irdma_hmc_info *irdma_vf_hmcinfo_from_fpm(struct irdma_sc_dev *dev,
 						 u8 hmc_fn_id);
-enum irdma_status_code irdma_add_sd_table_entry(struct irdma_hw *hw,
-						struct irdma_hmc_info *hmc_info,
-						u32 sd_index,
-						enum irdma_sd_entry_type type,
-						u64 direct_mode_sz);
-enum irdma_status_code irdma_add_pd_table_entry(struct irdma_sc_dev *dev,
-						struct irdma_hmc_info *hmc_info,
-						u32 pd_index,
-						struct irdma_dma_mem *rsrc_pg);
-enum irdma_status_code irdma_remove_pd_bp(struct irdma_sc_dev *dev,
-					  struct irdma_hmc_info *hmc_info,
-					  u32 idx);
-enum irdma_status_code irdma_prep_remove_sd_bp(struct irdma_hmc_info *hmc_info,
-					       u32 idx);
-enum irdma_status_code
-irdma_prep_remove_pd_page(struct irdma_hmc_info *hmc_info, u32 idx);
+int irdma_add_sd_table_entry(struct irdma_hw *hw,
+			     struct irdma_hmc_info *hmc_info, u32 sd_index,
+			     enum irdma_sd_entry_type type, u64 direct_mode_sz);
+int irdma_add_pd_table_entry(struct irdma_sc_dev *dev,
+			     struct irdma_hmc_info *hmc_info, u32 pd_index,
+			     struct irdma_dma_mem *rsrc_pg);
+int irdma_remove_pd_bp(struct irdma_sc_dev *dev,
+		       struct irdma_hmc_info *hmc_info, u32 idx);
+int irdma_prep_remove_sd_bp(struct irdma_hmc_info *hmc_info, u32 idx);
+int irdma_prep_remove_pd_page(struct irdma_hmc_info *hmc_info, u32 idx);
 #endif /* IRDMA_HMC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/hw.c
@@ -41,6 +41,7 @@
 	IRDMA_HMC_IW_XFFL,
 	IRDMA_HMC_IW_Q1,
 	IRDMA_HMC_IW_Q1FL,
+	IRDMA_HMC_IW_PBLE,
 	IRDMA_HMC_IW_TIMER,
 	IRDMA_HMC_IW_FSIMC,
 	IRDMA_HMC_IW_FSIAV,
@@ -60,6 +61,8 @@
 {
 	struct irdma_cq *cq = iwcq->back_cq;
 
+	if (!cq->user_mode)
+		atomic_set(&cq->armed, 0);
 	if (cq->ibcq.comp_handler)
 		cq->ibcq.comp_handler(&cq->ibcq, cq->ibcq.cq_context);
 }
@@ -73,12 +76,12 @@
 				  struct irdma_sc_cq *cq)
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
-	enum irdma_status_code status;
 	u32 compl_error;
+	int status;
 
 	do {
 		status = irdma_puda_poll_cmpl(dev, cq, &compl_error);
-		if (status == IRDMA_ERR_Q_EMPTY)
+		if (status == -ENOENT)
 			break;
 		if (status) {
 			ibdev_dbg(to_ibdev(dev), "ERR: puda status = %d\n", status);
@@ -136,56 +139,69 @@
 	qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
 
 	switch (info->ae_id) {
-	case IRDMA_AE_AMP_UNALLOCATED_STAG:
 	case IRDMA_AE_AMP_BOUNDS_VIOLATION:
 	case IRDMA_AE_AMP_INVALID_STAG:
-		qp->event_type = IRDMA_QP_EVENT_ACCESS_ERR;
-		fallthrough;
+	case IRDMA_AE_AMP_RIGHTS_VIOLATION:
+	case IRDMA_AE_AMP_UNALLOCATED_STAG:
 	case IRDMA_AE_AMP_BAD_PD:
-	case IRDMA_AE_UDA_XMIT_BAD_PD:
-		qp->flush_code = FLUSH_PROT_ERR;
-		break;
 	case IRDMA_AE_AMP_BAD_QP:
-		qp->flush_code = FLUSH_LOC_QP_OP_ERR;
-		break;
 	case IRDMA_AE_AMP_BAD_STAG_KEY:
 	case IRDMA_AE_AMP_BAD_STAG_INDEX:
 	case IRDMA_AE_AMP_TO_WRAP:
-	case IRDMA_AE_AMP_RIGHTS_VIOLATION:
-	case IRDMA_AE_AMP_INVALIDATE_NO_REMOTE_ACCESS_RIGHTS:
 	case IRDMA_AE_PRIV_OPERATION_DENIED:
-	case IRDMA_AE_IB_INVALID_REQUEST:
-	case IRDMA_AE_IB_REMOTE_ACCESS_ERROR:
-	case IRDMA_AE_IB_REMOTE_OP_ERROR:
-		qp->flush_code = FLUSH_REM_ACCESS_ERR;
+		qp->flush_code = FLUSH_PROT_ERR;
 		qp->event_type = IRDMA_QP_EVENT_ACCESS_ERR;
 		break;
-	case IRDMA_AE_LLP_SEGMENT_TOO_SMALL:
-	case IRDMA_AE_DDP_UBE_DDP_MESSAGE_TOO_LONG_FOR_AVAILABLE_BUFFER:
+	case IRDMA_AE_UDA_XMIT_BAD_PD:
+	case IRDMA_AE_WQE_UNEXPECTED_OPCODE:
+		qp->flush_code = FLUSH_LOC_QP_OP_ERR;
+		qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
+		break;
 	case IRDMA_AE_UDA_XMIT_DGRAM_TOO_LONG:
 	case IRDMA_AE_UDA_XMIT_DGRAM_TOO_SHORT:
 	case IRDMA_AE_UDA_L4LEN_INVALID:
-	case IRDMA_AE_ROCE_RSP_LENGTH_ERROR:
+	case IRDMA_AE_DDP_UBE_INVALID_MO:
+	case IRDMA_AE_DDP_UBE_DDP_MESSAGE_TOO_LONG_FOR_AVAILABLE_BUFFER:
 		qp->flush_code = FLUSH_LOC_LEN_ERR;
+		qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
+		break;
+	case IRDMA_AE_AMP_INVALIDATE_NO_REMOTE_ACCESS_RIGHTS:
+	case IRDMA_AE_IB_REMOTE_ACCESS_ERROR:
+		qp->flush_code = FLUSH_REM_ACCESS_ERR;
+		qp->event_type = IRDMA_QP_EVENT_ACCESS_ERR;
+		break;
+	case IRDMA_AE_LLP_SEGMENT_TOO_SMALL:
+	case IRDMA_AE_LLP_RECEIVED_MPA_CRC_ERROR:
+	case IRDMA_AE_ROCE_RSP_LENGTH_ERROR:
+	case IRDMA_AE_IB_REMOTE_OP_ERROR:
+		qp->flush_code = FLUSH_REM_OP_ERR;
+		qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
 		break;
 	case IRDMA_AE_LCE_QP_CATASTROPHIC:
 		qp->flush_code = FLUSH_FATAL_ERR;
+		qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
 		break;
-	case IRDMA_AE_DDP_UBE_INVALID_MO:
 	case IRDMA_AE_IB_RREQ_AND_Q1_FULL:
-	case IRDMA_AE_LLP_RECEIVED_MPA_CRC_ERROR:
 		qp->flush_code = FLUSH_GENERAL_ERR;
 		break;
 	case IRDMA_AE_LLP_TOO_MANY_RETRIES:
 		qp->flush_code = FLUSH_RETRY_EXC_ERR;
+		qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
 		break;
 	case IRDMA_AE_AMP_MWBIND_INVALID_RIGHTS:
 	case IRDMA_AE_AMP_MWBIND_BIND_DISABLED:
 	case IRDMA_AE_AMP_MWBIND_INVALID_BOUNDS:
+	case IRDMA_AE_AMP_MWBIND_VALID_STAG:
 		qp->flush_code = FLUSH_MW_BIND_ERR;
+		qp->event_type = IRDMA_QP_EVENT_ACCESS_ERR;
+		break;
+	case IRDMA_AE_IB_INVALID_REQUEST:
+		qp->flush_code = FLUSH_REM_INV_REQ_ERR;
+		qp->event_type = IRDMA_QP_EVENT_REQ_ERR;
 		break;
 	default:
-		qp->flush_code = FLUSH_FATAL_ERR;
+		qp->flush_code = FLUSH_GENERAL_ERR;
+		qp->event_type = IRDMA_QP_EVENT_CATASTROPHIC;
 		break;
 	}
 }
@@ -252,10 +268,6 @@
 				iwqp->last_aeq = info->ae_id;
 			spin_unlock_irqrestore(&iwqp->lock, flags);
 			ctx_info = &iwqp->ctx_info;
-			if (rdma_protocol_roce(&iwqp->iwdev->ibdev, 1))
-				ctx_info->roce_info->err_rq_idx_valid = true;
-			else
-				ctx_info->iwarp_info->err_rq_idx_valid = true;
 		} else {
 			if (info->ae_id != IRDMA_AE_CQ_OPERATION_ERROR)
 				continue;
@@ -310,7 +322,11 @@
 			break;
 		case IRDMA_AE_QP_SUSPEND_COMPLETE:
 			if (iwqp->iwdev->vsi.tc_change_pending) {
-				atomic_dec(&iwqp->sc_qp.vsi->qp_suspend_reqs);
+				if (!atomic_dec_return(&qp->vsi->qp_suspend_reqs))
+					wake_up(&iwqp->iwdev->suspend_wq);
+			}
+			if (iwqp->suspend_pending) {
+				iwqp->suspend_pending = false;
 				wake_up(&iwqp->iwdev->suspend_wq);
 			}
 			break;
@@ -363,18 +379,15 @@
 		case IRDMA_AE_LLP_TOO_MANY_RETRIES:
 		case IRDMA_AE_LCE_QP_CATASTROPHIC:
 		case IRDMA_AE_LCE_FUNCTION_CATASTROPHIC:
+		case IRDMA_AE_LLP_TOO_MANY_RNRS:
 		case IRDMA_AE_LCE_CQ_CATASTROPHIC:
 		case IRDMA_AE_UDA_XMIT_DGRAM_TOO_LONG:
-			if (rdma_protocol_roce(&iwdev->ibdev, 1))
-				ctx_info->roce_info->err_rq_idx_valid = false;
-			else
-				ctx_info->iwarp_info->err_rq_idx_valid = false;
-			fallthrough;
 		default:
 			ibdev_err(&iwdev->ibdev, "abnormal ae_id = 0x%x bool qp=%d qp_id = %d\n",
 				  info->ae_id, info->qp, info->qp_cq_id);
 			if (rdma_protocol_roce(&iwdev->ibdev, 1)) {
-				if (!info->sq && ctx_info->roce_info->err_rq_idx_valid) {
+				ctx_info->roce_info->err_rq_idx_valid = info->rq;
+				if (info->rq) {
 					ctx_info->roce_info->err_rq_idx = info->wqe_idx;
 					irdma_sc_qp_setctx_roce(&iwqp->sc_qp, iwqp->host_ctx.va,
 								ctx_info);
@@ -383,7 +396,8 @@
 				irdma_cm_disconn(iwqp);
 				break;
 			}
-			if (!info->sq && ctx_info->iwarp_info->err_rq_idx_valid) {
+			ctx_info->iwarp_info->err_rq_idx_valid = info->rq;
+			if (info->rq) {
 				ctx_info->iwarp_info->err_rq_idx = info->wqe_idx;
 				ctx_info->tcp_info_valid = false;
 				ctx_info->iwarp_info_valid = true;
@@ -451,7 +465,7 @@
  * Allocate iwdev msix table and copy the msix info to the table
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code irdma_save_msix_info(struct irdma_pci_f *rf)
+static int irdma_save_msix_info(struct irdma_pci_f *rf)
 {
 	struct irdma_qvlist_info *iw_qvlist;
 	struct irdma_qv_info *iw_qvinfo;
@@ -461,13 +475,13 @@
 	size_t size;
 
 	if (!rf->msix_count)
-		return IRDMA_ERR_NO_INTR;
+		return -EINVAL;
 
 	size = sizeof(struct irdma_msix_vector) * rf->msix_count;
 	size += struct_size(iw_qvlist, qv_info, rf->msix_count);
 	rf->iw_msixtbl = kzalloc(size, GFP_KERNEL);
 	if (!rf->iw_msixtbl)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	rf->iw_qvlist = (struct irdma_qvlist_info *)
 			(&rf->iw_msixtbl[rf->msix_count]);
@@ -476,6 +490,8 @@
 	iw_qvlist->num_vectors = rf->msix_count;
 	if (rf->msix_count <= num_online_cpus())
 		rf->msix_shared = true;
+	else if (rf->msix_count > num_online_cpus() + 1)
+		rf->msix_count = num_online_cpus() + 1;
 
 	pmsix = rf->msix_entries;
 	for (i = 0, ceq_idx = 0; i < rf->msix_count; i++, iw_qvinfo++) {
@@ -547,6 +563,13 @@
 	dev->irq_ops->irdma_dis_irq(dev, msix_vec->idx);
 	irq_set_affinity_hint(msix_vec->irq, NULL);
 	free_irq(msix_vec->irq, dev_id);
+	if (rf == dev_id) {
+		tasklet_kill(&rf->dpc_tasklet);
+	} else {
+		struct irdma_ceq *iwceq = (struct irdma_ceq *)dev_id;
+
+		tasklet_kill(&iwceq->dpc_tasklet);
+	}
 }
 
 /**
@@ -559,9 +582,9 @@
  */
 static void irdma_destroy_cqp(struct irdma_pci_f *rf, bool free_hwcqp)
 {
-	enum irdma_status_code status = 0;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_cqp *cqp = &rf->cqp;
+	int status = 0;
 
 	if (rf->cqp_cmpl_wq)
 		destroy_workqueue(rf->cqp_cmpl_wq);
@@ -601,9 +624,9 @@
  */
 static void irdma_destroy_aeq(struct irdma_pci_f *rf)
 {
-	enum irdma_status_code status = IRDMA_ERR_NOT_READY;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_aeq *aeq = &rf->aeq;
+	int status = -EBUSY;
 
 	if (!rf->msix_shared) {
 		rf->sc_dev.irq_ops->irdma_cfg_aeq(&rf->sc_dev, rf->iw_msixtbl->idx, false);
@@ -637,8 +660,8 @@
  */
 static void irdma_destroy_ceq(struct irdma_pci_f *rf, struct irdma_ceq *iwceq)
 {
-	enum irdma_status_code status;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
+	int status;
 
 	if (rf->reset)
 		goto exit;
@@ -728,7 +751,7 @@
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_ccq *ccq = &rf->ccq;
-	enum irdma_status_code status = 0;
+	int status = 0;
 
 	if (!rf->reset)
 		status = irdma_sc_ccq_destroy(dev->ccq, 0, true);
@@ -791,9 +814,8 @@
  * @dev: hardware control device structure
  * @info: information for the hmc object to create
  */
-static enum irdma_status_code
-irdma_create_hmc_obj_type(struct irdma_sc_dev *dev,
-			  struct irdma_hmc_create_obj_info *info)
+static int irdma_create_hmc_obj_type(struct irdma_sc_dev *dev,
+				     struct irdma_hmc_create_obj_info *info)
 {
 	return irdma_sc_create_hmc_obj(dev, info);
 }
@@ -807,19 +829,20 @@
  * Create the device hmc objects and allocate hmc pages
  * Return 0 if successful, otherwise clean up and return error
  */
-static enum irdma_status_code
-irdma_create_hmc_objs(struct irdma_pci_f *rf, bool privileged, enum irdma_vers vers)
+static int irdma_create_hmc_objs(struct irdma_pci_f *rf, bool privileged,
+				 enum irdma_vers vers)
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_hmc_create_obj_info info = {};
-	enum irdma_status_code status = 0;
-	int i;
+	int i, status = 0;
 
 	info.hmc_info = dev->hmc_info;
 	info.privileged = privileged;
 	info.entry_type = rf->sd_type;
 
 	for (i = 0; i < IW_HMC_OBJ_TYPE_NUM; i++) {
+		if (iw_hmc_obj_types[i] == IRDMA_HMC_IW_PBLE)
+			continue;
 		if (dev->hmc_info->hmc_obj[iw_hmc_obj_types[i]].cnt) {
 			info.rsrc_type = iw_hmc_obj_types[i];
 			info.count = dev->hmc_info->hmc_obj[info.rsrc_type].cnt;
@@ -863,9 +886,9 @@
  * update the memptr to point to the new aligned memory
  * Return 0 if successful, otherwise return no memory error
  */
-static enum irdma_status_code
-irdma_obj_aligned_mem(struct irdma_pci_f *rf, struct irdma_dma_mem *memptr,
-		      u32 size, u32 mask)
+static int irdma_obj_aligned_mem(struct irdma_pci_f *rf,
+				 struct irdma_dma_mem *memptr, u32 size,
+				 u32 mask)
 {
 	unsigned long va, newva;
 	unsigned long extra;
@@ -879,7 +902,7 @@
 	memptr->pa = rf->obj_next.pa + extra;
 	memptr->size = size;
 	if (((u8 *)memptr->va + size) > ((u8 *)rf->obj_mem.va + rf->obj_mem.size))
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	rf->obj_next.va = (u8 *)memptr->va + size;
 	rf->obj_next.pa = memptr->pa + size;
@@ -894,25 +917,24 @@
  * Return 0, if the cqp and all the resources associated with it
  * are successfully created, otherwise return error
  */
-static enum irdma_status_code irdma_create_cqp(struct irdma_pci_f *rf)
+static int irdma_create_cqp(struct irdma_pci_f *rf)
 {
-	enum irdma_status_code status;
 	u32 sqsize = IRDMA_CQP_SW_SQSIZE_2048;
 	struct irdma_dma_mem mem;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_cqp_init_info cqp_init_info = {};
 	struct irdma_cqp *cqp = &rf->cqp;
 	u16 maj_err, min_err;
-	int i;
+	int i, status;
 
 	cqp->cqp_requests = kcalloc(sqsize, sizeof(*cqp->cqp_requests), GFP_KERNEL);
 	if (!cqp->cqp_requests)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp->scratch_array = kcalloc(sqsize, sizeof(*cqp->scratch_array), GFP_KERNEL);
 	if (!cqp->scratch_array) {
 		kfree(cqp->cqp_requests);
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 
 	dev->cqp = &cqp->sc_cqp;
@@ -924,7 +946,7 @@
 	if (!cqp->sq.va) {
 		kfree(cqp->scratch_array);
 		kfree(cqp->cqp_requests);
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 
 	status = irdma_obj_aligned_mem(rf, &mem, sizeof(struct irdma_cqp_ctx),
@@ -994,12 +1016,12 @@
  * Return 0, if the ccq and the resources associated with it
  * are successfully created, otherwise return error
  */
-static enum irdma_status_code irdma_create_ccq(struct irdma_pci_f *rf)
+static int irdma_create_ccq(struct irdma_pci_f *rf)
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
-	enum irdma_status_code status;
 	struct irdma_ccq_init_info info = {};
 	struct irdma_ccq *ccq = &rf->ccq;
+	int status;
 
 	dev->ccq = &ccq->sc_cq;
 	dev->ccq->dev = dev;
@@ -1010,7 +1032,7 @@
 	ccq->mem_cq.va = dma_alloc_coherent(dev->hw->device, ccq->mem_cq.size,
 					    &ccq->mem_cq.pa, GFP_KERNEL);
 	if (!ccq->mem_cq.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	status = irdma_obj_aligned_mem(rf, &ccq->shadow_area,
 				       ccq->shadow_area.size,
@@ -1049,9 +1071,9 @@
  * Allocate a mac ip entry and add it to the hw table Return 0
  * if successful, otherwise return error
  */
-static enum irdma_status_code irdma_alloc_set_mac(struct irdma_device *iwdev)
+static int irdma_alloc_set_mac(struct irdma_device *iwdev)
 {
-	enum irdma_status_code status;
+	int status;
 
 	status = irdma_alloc_local_mac_entry(iwdev->rf,
 					     &iwdev->mac_ip_table_idx);
@@ -1077,9 +1099,8 @@
  * Allocate interrupt resources and enable irq handling
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code
-irdma_cfg_ceq_vector(struct irdma_pci_f *rf, struct irdma_ceq *iwceq,
-		     u32 ceq_id, struct irdma_msix_vector *msix_vec)
+static int irdma_cfg_ceq_vector(struct irdma_pci_f *rf, struct irdma_ceq *iwceq,
+				u32 ceq_id, struct irdma_msix_vector *msix_vec)
 {
 	int status;
 
@@ -1098,7 +1119,7 @@
 	irq_set_affinity_hint(msix_vec->irq, &msix_vec->mask);
 	if (status) {
 		ibdev_dbg(&rf->iwdev->ibdev, "ERR: ceq irq config fail\n");
-		return IRDMA_ERR_CFG;
+		return -EINVAL;
 	}
 
 	msix_vec->ceq_id = ceq_id;
@@ -1114,7 +1135,7 @@
  * Allocate interrupt resources and enable irq handling
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code irdma_cfg_aeq_vector(struct irdma_pci_f *rf)
+static int irdma_cfg_aeq_vector(struct irdma_pci_f *rf)
 {
 	struct irdma_msix_vector *msix_vec = rf->iw_msixtbl;
 	u32 ret = 0;
@@ -1126,7 +1147,7 @@
 	}
 	if (ret) {
 		ibdev_dbg(&rf->iwdev->ibdev, "ERR: aeq irq config fail\n");
-		return IRDMA_ERR_CFG;
+		return -EINVAL;
 	}
 
 	rf->sc_dev.irq_ops->irdma_cfg_aeq(&rf->sc_dev, msix_vec->idx, true);
@@ -1144,15 +1165,12 @@
  * Return 0, if the ceq and the resources associated with it
  * are successfully created, otherwise return error
  */
-static enum irdma_status_code irdma_create_ceq(struct irdma_pci_f *rf,
-					       struct irdma_ceq *iwceq,
-					       u32 ceq_id,
-					       struct irdma_sc_vsi *vsi)
+static int irdma_create_ceq(struct irdma_pci_f *rf, struct irdma_ceq *iwceq,
+			    u32 ceq_id, struct irdma_sc_vsi *vsi)
 {
-	enum irdma_status_code status;
+	int status;
 	struct irdma_ceq_init_info info = {};
 	struct irdma_sc_dev *dev = &rf->sc_dev;
-	u64 scratch;
 	u32 ceq_size;
 
 	info.ceq_id = ceq_id;
@@ -1164,7 +1182,7 @@
 	iwceq->mem.va = dma_alloc_coherent(dev->hw->device, iwceq->mem.size,
 					   &iwceq->mem.pa, GFP_KERNEL);
 	if (!iwceq->mem.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	info.ceq_id = ceq_id;
 	info.ceqe_base = iwceq->mem.va;
@@ -1173,14 +1191,13 @@
 	iwceq->sc_ceq.ceq_id = ceq_id;
 	info.dev = dev;
 	info.vsi = vsi;
-	scratch = (uintptr_t)&rf->cqp.sc_cqp;
 	status = irdma_sc_ceq_init(&iwceq->sc_ceq, &info);
 	if (!status) {
 		if (dev->ceq_valid)
 			status = irdma_cqp_ceq_cmd(&rf->sc_dev, &iwceq->sc_ceq,
 						   IRDMA_OP_CEQ_CREATE);
 		else
-			status = irdma_sc_cceq_create(&iwceq->sc_ceq, scratch);
+			status = irdma_sc_cceq_create(&iwceq->sc_ceq, 0);
 	}
 
 	if (status) {
@@ -1200,18 +1217,18 @@
  * Create the ceq 0 and configure it's msix interrupt vector
  * Return 0, if successfully set up, otherwise return error
  */
-static enum irdma_status_code irdma_setup_ceq_0(struct irdma_pci_f *rf)
+static int irdma_setup_ceq_0(struct irdma_pci_f *rf)
 {
 	struct irdma_ceq *iwceq;
 	struct irdma_msix_vector *msix_vec;
 	u32 i;
-	enum irdma_status_code status = 0;
+	int status = 0;
 	u32 num_ceqs;
 
 	num_ceqs = min(rf->msix_count, rf->sc_dev.hmc_fpm_misc.max_ceqs);
 	rf->ceqlist = kcalloc(num_ceqs, sizeof(*rf->ceqlist), GFP_KERNEL);
 	if (!rf->ceqlist) {
-		status = IRDMA_ERR_NO_MEMORY;
+		status = -ENOMEM;
 		goto exit;
 	}
 
@@ -1257,14 +1274,13 @@
  * Create the ceq's and configure their msix interrupt vectors
  * Return 0, if ceqs are successfully set up, otherwise return error
  */
-static enum irdma_status_code irdma_setup_ceqs(struct irdma_pci_f *rf,
-					       struct irdma_sc_vsi *vsi)
+static int irdma_setup_ceqs(struct irdma_pci_f *rf, struct irdma_sc_vsi *vsi)
 {
 	u32 i;
 	u32 ceq_id;
 	struct irdma_ceq *iwceq;
 	struct irdma_msix_vector *msix_vec;
-	enum irdma_status_code status;
+	int status;
 	u32 num_ceqs;
 
 	num_ceqs = min(rf->msix_count, rf->sc_dev.hmc_fpm_misc.max_ceqs);
@@ -1298,22 +1314,21 @@
 	return status;
 }
 
-static enum irdma_status_code irdma_create_virt_aeq(struct irdma_pci_f *rf,
-						    u32 size)
+static int irdma_create_virt_aeq(struct irdma_pci_f *rf, u32 size)
 {
-	enum irdma_status_code status = IRDMA_ERR_NO_MEMORY;
 	struct irdma_aeq *aeq = &rf->aeq;
 	dma_addr_t *pg_arr;
 	u32 pg_cnt;
+	int status;
 
 	if (rf->rdma_ver < IRDMA_GEN_2)
-		return IRDMA_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 
 	aeq->mem.size = sizeof(struct irdma_sc_aeqe) * size;
 	aeq->mem.va = vzalloc(aeq->mem.size);
 
 	if (!aeq->mem.va)
-		return status;
+		return -ENOMEM;
 
 	pg_cnt = DIV_ROUND_UP(aeq->mem.size, PAGE_SIZE);
 	status = irdma_get_pble(rf->pble_rsrc, &aeq->palloc, pg_cnt, true);
@@ -1340,15 +1355,15 @@
  * Return 0, if the aeq and the resources associated with it
  * are successfully created, otherwise return error
  */
-static enum irdma_status_code irdma_create_aeq(struct irdma_pci_f *rf)
+static int irdma_create_aeq(struct irdma_pci_f *rf)
 {
-	enum irdma_status_code status;
 	struct irdma_aeq_init_info info = {};
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_aeq *aeq = &rf->aeq;
 	struct irdma_hmc_info *hmc_info = rf->sc_dev.hmc_info;
 	u32 aeq_size;
 	u8 multiplier = (rf->protocol_used == IRDMA_IWARP_PROTOCOL_ONLY) ? 2 : 1;
+	int status;
 
 	aeq_size = multiplier * hmc_info->hmc_obj[IRDMA_HMC_IW_QP].cnt +
 		   hmc_info->hmc_obj[IRDMA_HMC_IW_CQ].cnt;
@@ -1407,10 +1422,10 @@
  * Create the aeq and configure its msix interrupt vector
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code irdma_setup_aeq(struct irdma_pci_f *rf)
+static int irdma_setup_aeq(struct irdma_pci_f *rf)
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
-	enum irdma_status_code status;
+	int status;
 
 	status = irdma_create_aeq(rf);
 	if (status)
@@ -1434,10 +1449,10 @@
  *
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code irdma_initialize_ilq(struct irdma_device *iwdev)
+static int irdma_initialize_ilq(struct irdma_device *iwdev)
 {
 	struct irdma_puda_rsrc_info info = {};
-	enum irdma_status_code status;
+	int status;
 
 	info.type = IRDMA_PUDA_RSRC_TYPE_ILQ;
 	info.cq_id = 1;
@@ -1464,10 +1479,10 @@
  *
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code irdma_initialize_ieq(struct irdma_device *iwdev)
+static int irdma_initialize_ieq(struct irdma_device *iwdev)
 {
 	struct irdma_puda_rsrc_info info = {};
-	enum irdma_status_code status;
+	int status;
 
 	info.type = IRDMA_PUDA_RSRC_TYPE_IEQ;
 	info.cq_id = 2;
@@ -1510,9 +1525,9 @@
  * the hmc objects and create the objects
  * Return 0 if successful, otherwise return error
  */
-static enum irdma_status_code irdma_hmc_setup(struct irdma_pci_f *rf)
+static int irdma_hmc_setup(struct irdma_pci_f *rf)
 {
-	enum irdma_status_code status;
+	int status;
 	u32 qpcnt;
 
 	if (rf->rdma_ver == IRDMA_GEN_1)
@@ -1565,9 +1580,9 @@
  * Return 0 if successful, otherwise clean up the resources
  * and return error
  */
-static enum irdma_status_code irdma_initialize_dev(struct irdma_pci_f *rf)
+static int irdma_initialize_dev(struct irdma_pci_f *rf)
 {
-	enum irdma_status_code status;
+	int status;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_device_init_info info = {};
 	struct irdma_dma_mem mem;
@@ -1579,7 +1594,7 @@
 
 	rf->hmc_info_mem = kzalloc(size, GFP_KERNEL);
 	if (!rf->hmc_info_mem)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	rf->pble_rsrc = (struct irdma_hmc_pble_rsrc *)rf->hmc_info_mem;
 	dev->hmc_info = &rf->hw.hmc;
@@ -1603,7 +1618,7 @@
 	info.fpm_commit_buf = mem.va;
 
 	info.bar0 = rf->hw.hw_addr;
-	info.hmc_fn_id = PCI_FUNC(rf->pcidev->devfn);
+	info.hmc_fn_id = rf->pf_id;
 	info.hw = &rf->hw;
 	status = irdma_sc_dev_init(rf->rdma_ver, &rf->sc_dev, &info);
 	if (status)
@@ -1662,9 +1677,9 @@
 		destroy_workqueue(iwdev->cleanup_wq);
 }
 
-static enum irdma_status_code irdma_setup_init_state(struct irdma_pci_f *rf)
+static int irdma_setup_init_state(struct irdma_pci_f *rf)
 {
-	enum irdma_status_code status;
+	int status;
 
 	status = irdma_save_msix_info(rf);
 	if (status)
@@ -1675,7 +1690,7 @@
 	rf->obj_mem.va = dma_alloc_coherent(rf->hw.device, rf->obj_mem.size,
 					    &rf->obj_mem.pa, GFP_KERNEL);
 	if (!rf->obj_mem.va) {
-		status = IRDMA_ERR_NO_MEMORY;
+		status = -ENOMEM;
 		goto clean_msixtbl;
 	}
 
@@ -1758,14 +1773,14 @@
  * Create device queues ILQ, IEQ, CEQs and PBLEs. Setup irdma
  * device resource objects.
  */
-enum irdma_status_code irdma_rt_init_hw(struct irdma_device *iwdev,
-					struct irdma_l2params *l2params)
+int irdma_rt_init_hw(struct irdma_device *iwdev,
+		     struct irdma_l2params *l2params)
 {
 	struct irdma_pci_f *rf = iwdev->rf;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
-	enum irdma_status_code status;
 	struct irdma_vsi_init_info vsi_info = {};
 	struct irdma_vsi_stats_info stats_info = {};
+	int status;
 
 	vsi_info.dev = dev;
 	vsi_info.back_vsi = iwdev;
@@ -1783,7 +1798,7 @@
 	stats_info.pestat = kzalloc(sizeof(*stats_info.pestat), GFP_KERNEL);
 	if (!stats_info.pestat) {
 		irdma_cleanup_cm_core(&iwdev->cm_core);
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 	stats_info.fcn_id = dev->hmc_fn_id;
 	status = irdma_vsi_stats_init(&iwdev->vsi, &stats_info);
@@ -1845,7 +1860,7 @@
 		iwdev->cleanup_wq = alloc_workqueue("irdma-cleanup-wq",
 					WQ_UNBOUND, WQ_UNBOUND_MAX_ACTIVE);
 		if (!iwdev->cleanup_wq)
-			return IRDMA_ERR_NO_MEMORY;
+			return -ENOMEM;
 		irdma_get_used_rsrc(iwdev);
 		init_waitqueue_head(&iwdev->suspend_wq);
 
@@ -1865,10 +1880,10 @@
  *
  * Create admin queues, HMC obejcts and RF resource objects
  */
-enum irdma_status_code irdma_ctrl_init_hw(struct irdma_pci_f *rf)
+int irdma_ctrl_init_hw(struct irdma_pci_f *rf)
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
-	enum irdma_status_code status;
+	int status;
 	do {
 		status = irdma_setup_init_state(rf);
 		if (status)
@@ -1910,7 +1925,7 @@
 		rf->cqp_cmpl_wq = alloc_ordered_workqueue("cqp_cmpl_wq",
 						WQ_HIGHPRI | WQ_UNBOUND);
 		if (!rf->cqp_cmpl_wq) {
-			status = IRDMA_ERR_NO_MEMORY;
+			status = -ENOMEM;
 			break;
 		}
 		INIT_WORK(&rf->cqp_cmpl_work, cqp_compl_worker);
@@ -2072,7 +2087,7 @@
 			cqp_request->compl_info.error = info.error;
 
 			if (cqp_request->waiting) {
-				cqp_request->request_done = true;
+				WRITE_ONCE(cqp_request->request_done, true);
 				wake_up(&cqp_request->waitq);
 				irdma_put_cqp_request(&rf->cqp, cqp_request);
 			} else {
@@ -2197,11 +2212,11 @@
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_info->post_sq = 1;
@@ -2233,11 +2248,11 @@
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status = 0;
+	int status = 0;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_info->cqp_cmd = IRDMA_OP_ALLOC_LOCAL_MAC_ENTRY;
@@ -2259,18 +2274,17 @@
  * @accel_local_port: port for apbvt
  * @add_port: add ordelete port
  */
-static enum irdma_status_code
-irdma_cqp_manage_apbvt_cmd(struct irdma_device *iwdev, u16 accel_local_port,
-			   bool add_port)
+static int irdma_cqp_manage_apbvt_cmd(struct irdma_device *iwdev,
+				      u16 accel_local_port, bool add_port)
 {
 	struct irdma_apbvt_info *info;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&iwdev->rf->cqp, add_port);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	info = &cqp_info->in.u.manage_apbvt_entry.info;
@@ -2423,22 +2437,21 @@
  * @cmnode: cmnode associated with connection
  * @wait: wait for completion
  */
-enum irdma_status_code
-irdma_manage_qhash(struct irdma_device *iwdev, struct irdma_cm_info *cminfo,
-		   enum irdma_quad_entry_type etype,
-		   enum irdma_quad_hash_manage_type mtype, void *cmnode,
-		   bool wait)
+int irdma_manage_qhash(struct irdma_device *iwdev, struct irdma_cm_info *cminfo,
+		       enum irdma_quad_entry_type etype,
+		       enum irdma_quad_hash_manage_type mtype, void *cmnode,
+		       bool wait)
 {
 	struct irdma_qhash_table_info *info;
-	enum irdma_status_code status;
 	struct irdma_cqp *iwcqp = &iwdev->rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_cm_node *cm_node = cmnode;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, wait);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	info = &cqp_info->in.u.manage_qhash_table_entry.info;
@@ -2552,12 +2565,10 @@
  * @info: info for flush
  * @wait: flag wait for completion
  */
-enum irdma_status_code irdma_hw_flush_wqes(struct irdma_pci_f *rf,
-					   struct irdma_sc_qp *qp,
-					   struct irdma_qp_flush_info *info,
-					   bool wait)
+int irdma_hw_flush_wqes(struct irdma_pci_f *rf, struct irdma_sc_qp *qp,
+			struct irdma_qp_flush_info *info, bool wait)
 {
-	enum irdma_status_code status;
+	int status;
 	struct irdma_qp_flush_info *hw_info;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
@@ -2565,7 +2576,7 @@
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, wait);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	if (!wait)
@@ -2613,7 +2624,7 @@
 				info->sq = true;
 				new_req = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 				if (!new_req) {
-					status = IRDMA_ERR_NO_MEMORY;
+					status = -ENOMEM;
 					goto put_cqp;
 				}
 				cqp_info = &new_req->info;
@@ -2699,24 +2710,29 @@
 	info.sq = flush_mask & IRDMA_FLUSH_SQ;
 	info.rq = flush_mask & IRDMA_FLUSH_RQ;
 
-	if (flush_mask & IRDMA_REFLUSH) {
-		if (info.sq)
-			iwqp->sc_qp.flush_sq = false;
-		if (info.rq)
-			iwqp->sc_qp.flush_rq = false;
-	}
-
 	/* Generate userflush errors in CQE */
 	info.sq_major_code = IRDMA_FLUSH_MAJOR_ERR;
 	info.sq_minor_code = FLUSH_GENERAL_ERR;
 	info.rq_major_code = IRDMA_FLUSH_MAJOR_ERR;
 	info.rq_minor_code = FLUSH_GENERAL_ERR;
 	info.userflushcode = true;
-	if (flush_code) {
-		if (info.sq && iwqp->sc_qp.sq_flush_code)
-			info.sq_minor_code = flush_code;
-		if (info.rq && iwqp->sc_qp.rq_flush_code)
-			info.rq_minor_code = flush_code;
+
+	if (flush_mask & IRDMA_REFLUSH) {
+		if (info.sq)
+			iwqp->sc_qp.flush_sq = false;
+		if (info.rq)
+			iwqp->sc_qp.flush_rq = false;
+	} else {
+		if (flush_code) {
+			if (info.sq && iwqp->sc_qp.sq_flush_code)
+				info.sq_minor_code = flush_code;
+			if (info.rq && iwqp->sc_qp.rq_flush_code)
+				info.rq_minor_code = flush_code;
+		}
+		if (!iwqp->user_mode)
+			queue_delayed_work(iwqp->iwdev->cleanup_wq,
+					   &iwqp->dwork_flush,
+					   msecs_to_jiffies(IRDMA_FLUSH_DELAY_MS));
 	}
 
 	/* Issue flush */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/i40iw_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/i40iw_hw.c
@@ -3,7 +3,6 @@
 #include "osdep.h"
 #include "type.h"
 #include "i40iw_hw.h"
-#include "status.h"
 #include "protos.h"
 
 static u32 i40iw_regs[IRDMA_MAX_REGS] = {
@@ -202,6 +201,7 @@
 	dev->hw_attrs.uk_attrs.max_hw_read_sges = I40IW_MAX_SGE_RD;
 	dev->hw_attrs.max_hw_device_pages = I40IW_MAX_PUSH_PAGE_COUNT;
 	dev->hw_attrs.uk_attrs.max_hw_inline = I40IW_MAX_INLINE_DATA_SIZE;
+	dev->hw_attrs.page_size_cap = SZ_4K | SZ_2M;
 	dev->hw_attrs.max_hw_ird = I40IW_MAX_IRD_SIZE;
 	dev->hw_attrs.max_hw_ord = I40IW_MAX_ORD_SIZE;
 	dev->hw_attrs.max_hw_wqes = I40IW_MAX_WQ_ENTRIES;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/i40iw_if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/i40iw_if.c
@@ -77,6 +77,7 @@
 	rf->rdma_ver = IRDMA_GEN_1;
 	rf->gen_ops.request_reset = i40iw_request_reset;
 	rf->pcidev = cdev_info->pcidev;
+	rf->pf_id = cdev_info->fid;
 	rf->hw.hw_addr = cdev_info->hw_addr;
 	rf->cdev = cdev_info;
 	rf->msix_count = cdev_info->msix_count;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/icrdma_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/icrdma_hw.c
@@ -139,6 +139,7 @@
 	dev->cqp_db = dev->hw_regs[IRDMA_CQPDB];
 	dev->cq_ack_db = dev->hw_regs[IRDMA_CQACK];
 	dev->irq_ops = &icrdma_irq_ops;
+	dev->hw_attrs.page_size_cap = SZ_4K | SZ_2M | SZ_1G;
 	dev->hw_attrs.max_hw_ird = ICRDMA_MAX_IRD_SIZE;
 	dev->hw_attrs.max_hw_ord = ICRDMA_MAX_ORD_SIZE;
 	dev->hw_attrs.max_stat_inst = ICRDMA_MAX_STATS_COUNT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/irdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/irdma.h
@@ -127,6 +127,7 @@
 	u64 max_hw_outbound_msg_size;
 	u64 max_hw_inbound_msg_size;
 	u64 max_mr_size;
+	u64 page_size_cap;
 	u32 min_hw_qp_id;
 	u32 min_hw_aeq_size;
 	u32 max_hw_aeq_size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/main.c
@@ -48,7 +48,7 @@
 	/* Wait for all qp's to suspend */
 	wait_event_timeout(iwdev->suspend_wq,
 			   !atomic_read(&iwdev->vsi.qp_suspend_reqs),
-			   IRDMA_EVENT_TIMEOUT);
+			   msecs_to_jiffies(IRDMA_EVENT_TIMEOUT_MS));
 	irdma_ws_reset(&iwdev->vsi);
 }
 
@@ -157,8 +157,8 @@
  * @vsi: vsi structure
  * @tc_node: Traffic class node
  */
-static enum irdma_status_code irdma_lan_register_qset(struct irdma_sc_vsi *vsi,
-						      struct irdma_ws_node *tc_node)
+static int irdma_lan_register_qset(struct irdma_sc_vsi *vsi,
+				   struct irdma_ws_node *tc_node)
 {
 	struct irdma_device *iwdev = vsi->back_vsi;
 	struct ice_pf *pf = iwdev->rf->cdev;
@@ -171,7 +171,7 @@
 	ret = ice_add_rdma_qset(pf, &qset);
 	if (ret) {
 		ibdev_dbg(&iwdev->ibdev, "WS: LAN alloc_res for rdma qset failed.\n");
-		return IRDMA_ERR_REG_QSET;
+		return -EINVAL;
 	}
 
 	tc_node->l2_sched_node_id = qset.teid;
@@ -226,6 +226,7 @@
 	rf->hw.hw_addr = pf->hw.hw_addr;
 	rf->pcidev = pf->pdev;
 	rf->msix_count =  pf->num_rdma_msix;
+	rf->pf_id = pf->hw.pf_id;
 	rf->msix_entries = &pf->msix_entries[pf->rdma_base_vector];
 	rf->default_vsi.vsi_idx = vsi->vsi_num;
 	rf->protocol_used = IRDMA_ROCE_PROTOCOL_ONLY;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/main.h
@@ -40,7 +40,6 @@
 #include <rdma/ib_umem.h>
 #include <rdma/ib_cache.h>
 #include <rdma/uverbs_ioctl.h>
-#include "status.h"
 #include "osdep.h"
 #include "defs.h"
 #include "hmc.h"
@@ -79,7 +78,7 @@
 
 #define MAX_DPC_ITERATIONS	128
 
-#define IRDMA_EVENT_TIMEOUT		50000
+#define IRDMA_EVENT_TIMEOUT_MS		5000
 #define IRDMA_VCHNL_EVENT_TIMEOUT	100000
 #define IRDMA_RST_TIMEOUT_HZ		4
 
@@ -160,8 +159,8 @@
 	void (*callback_fcn)(struct irdma_cqp_request *cqp_request);
 	void *param;
 	struct irdma_cqp_compl_info compl_info;
+	bool request_done; /* READ/WRITE_ONCE macros operate on it */
 	bool waiting:1;
-	bool request_done:1;
 	bool dynamic:1;
 };
 
@@ -237,13 +236,13 @@
 
 struct irdma_qvlist_info {
 	u32 num_vectors;
-	struct irdma_qv_info qv_info[1];
+	struct irdma_qv_info qv_info[];
 };
 
 struct irdma_gen_ops {
 	void (*request_reset)(struct irdma_pci_f *rf);
-	enum irdma_status_code (*register_qset)(struct irdma_sc_vsi *vsi,
-						struct irdma_ws_node *tc_node);
+	int (*register_qset)(struct irdma_sc_vsi *vsi,
+			     struct irdma_ws_node *tc_node);
 	void (*unregister_qset)(struct irdma_sc_vsi *vsi,
 				struct irdma_ws_node *tc_node);
 };
@@ -257,6 +256,7 @@
 	u8 *mem_rsrc;
 	u8 rdma_ver;
 	u8 rst_to;
+	u8 pf_id;
 	enum irdma_protocol_used protocol_used;
 	u32 sd_type;
 	u32 msix_count;
@@ -457,10 +457,10 @@
 	spin_unlock_irqrestore(&rf->rsrc_lock, flags);
 }
 
-enum irdma_status_code irdma_ctrl_init_hw(struct irdma_pci_f *rf);
+int irdma_ctrl_init_hw(struct irdma_pci_f *rf);
 void irdma_ctrl_deinit_hw(struct irdma_pci_f *rf);
-enum irdma_status_code irdma_rt_init_hw(struct irdma_device *iwdev,
-					struct irdma_l2params *l2params);
+int irdma_rt_init_hw(struct irdma_device *iwdev,
+		     struct irdma_l2params *l2params);
 void irdma_rt_deinit_hw(struct irdma_device *iwdev);
 void irdma_qp_add_ref(struct ib_qp *ibqp);
 void irdma_qp_rem_ref(struct ib_qp *ibqp);
@@ -488,9 +488,8 @@
 
 bool irdma_cqp_crit_err(struct irdma_sc_dev *dev, u8 cqp_cmd,
 			u16 maj_err_code, u16 min_err_code);
-enum irdma_status_code
-irdma_handle_cqp_op(struct irdma_pci_f *rf,
-		    struct irdma_cqp_request *cqp_request);
+int irdma_handle_cqp_op(struct irdma_pci_f *rf,
+			struct irdma_cqp_request *cqp_request);
 
 int irdma_modify_qp(struct ib_qp *ibqp, struct ib_qp_attr *attr, int attr_mask,
 		    struct ib_udata *udata);
@@ -499,21 +498,17 @@
 void irdma_cq_wq_destroy(struct irdma_pci_f *rf, struct irdma_sc_cq *cq);
 
 void irdma_cleanup_pending_cqp_op(struct irdma_pci_f *rf);
-enum irdma_status_code irdma_hw_modify_qp(struct irdma_device *iwdev,
-					  struct irdma_qp *iwqp,
-					  struct irdma_modify_qp_info *info,
-					  bool wait);
-enum irdma_status_code irdma_qp_suspend_resume(struct irdma_sc_qp *qp,
-					       bool suspend);
-enum irdma_status_code
-irdma_manage_qhash(struct irdma_device *iwdev, struct irdma_cm_info *cminfo,
-		   enum irdma_quad_entry_type etype,
-		   enum irdma_quad_hash_manage_type mtype, void *cmnode,
-		   bool wait);
+int irdma_hw_modify_qp(struct irdma_device *iwdev, struct irdma_qp *iwqp,
+		       struct irdma_modify_qp_info *info, bool wait);
+int irdma_qp_suspend_resume(struct irdma_sc_qp *qp, bool suspend);
+int irdma_manage_qhash(struct irdma_device *iwdev, struct irdma_cm_info *cminfo,
+		       enum irdma_quad_entry_type etype,
+		       enum irdma_quad_hash_manage_type mtype, void *cmnode,
+		       bool wait);
 void irdma_receive_ilq(struct irdma_sc_vsi *vsi, struct irdma_puda_buf *rbuf);
 void irdma_free_sqbuf(struct irdma_sc_vsi *vsi, void *bufp);
 void irdma_free_qp_rsrc(struct irdma_qp *iwqp);
-enum irdma_status_code irdma_setup_cm_core(struct irdma_device *iwdev, u8 ver);
+int irdma_setup_cm_core(struct irdma_device *iwdev, u8 ver);
 void irdma_cleanup_cm_core(struct irdma_cm_core *cm_core);
 void irdma_next_iw_state(struct irdma_qp *iwqp, u8 state, u8 del_hash, u8 term,
 			 u8 term_len);
@@ -522,10 +517,8 @@
 struct irdma_cm_node *irdma_find_node(struct irdma_cm_core *cm_core,
 				      u16 rem_port, u32 *rem_addr, u16 loc_port,
 				      u32 *loc_addr, u16 vlan_id);
-enum irdma_status_code irdma_hw_flush_wqes(struct irdma_pci_f *rf,
-					   struct irdma_sc_qp *qp,
-					   struct irdma_qp_flush_info *info,
-					   bool wait);
+int irdma_hw_flush_wqes(struct irdma_pci_f *rf, struct irdma_sc_qp *qp,
+			struct irdma_qp_flush_info *info, bool wait);
 void irdma_gen_ae(struct irdma_pci_f *rf, struct irdma_sc_qp *qp,
 		  struct irdma_gen_ae_info *info, bool wait);
 void irdma_copy_ip_ntohl(u32 *dst, __be32 *src);
@@ -541,6 +534,7 @@
 		    void (*callback_fcn)(struct irdma_cqp_request *cqp_request),
 		    void *cb_param);
 void irdma_gsi_ud_qp_ah_cb(struct irdma_cqp_request *cqp_request);
+bool irdma_cq_empty(struct irdma_cq *iwcq);
 int irdma_inetaddr_event(struct notifier_block *notifier, unsigned long event,
 			 void *ptr);
 int irdma_inet6addr_event(struct notifier_block *notifier, unsigned long event,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/osdep.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/osdep.h
@@ -37,38 +37,33 @@
 struct irdma_pci_f;
 
 struct ib_device *to_ibdev(struct irdma_sc_dev *dev);
-u8 __iomem *irdma_get_hw_addr(void *dev);
 void irdma_ieq_mpa_crc_ae(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp);
 enum irdma_status_code irdma_vf_wait_vchnl_resp(struct irdma_sc_dev *dev);
 bool irdma_vf_clear_to_send(struct irdma_sc_dev *dev);
 void irdma_add_dev_ref(struct irdma_sc_dev *dev);
 void irdma_put_dev_ref(struct irdma_sc_dev *dev);
-enum irdma_status_code irdma_ieq_check_mpacrc(struct shash_desc *desc,
-					      void *addr, u32 len, u32 val);
+int irdma_ieq_check_mpacrc(struct shash_desc *desc, void *addr, u32 len,
+			   u32 val);
 struct irdma_sc_qp *irdma_ieq_get_qp(struct irdma_sc_dev *dev,
 				     struct irdma_puda_buf *buf);
 void irdma_send_ieq_ack(struct irdma_sc_qp *qp);
 void irdma_ieq_update_tcpip_info(struct irdma_puda_buf *buf, u16 len,
 				 u32 seqnum);
 void irdma_free_hash_desc(struct shash_desc *hash_desc);
-enum irdma_status_code irdma_init_hash_desc(struct shash_desc **hash_desc);
-enum irdma_status_code
-irdma_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
-			  struct irdma_puda_buf *buf);
-enum irdma_status_code irdma_cqp_sds_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_update_sds_info *info);
-enum irdma_status_code
-irdma_cqp_manage_hmc_fcn_cmd(struct irdma_sc_dev *dev,
-			     struct irdma_hmc_fcn_info *hmcfcninfo,
-			     u16 *pmf_idx);
-enum irdma_status_code
-irdma_cqp_query_fpm_val_cmd(struct irdma_sc_dev *dev,
-			    struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
-enum irdma_status_code
-irdma_cqp_commit_fpm_val_cmd(struct irdma_sc_dev *dev,
-			     struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
-enum irdma_status_code irdma_alloc_query_fpm_buf(struct irdma_sc_dev *dev,
-						 struct irdma_dma_mem *mem);
+int irdma_init_hash_desc(struct shash_desc **hash_desc);
+int irdma_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
+			      struct irdma_puda_buf *buf);
+int irdma_cqp_sds_cmd(struct irdma_sc_dev *dev,
+		      struct irdma_update_sds_info *info);
+int irdma_cqp_manage_hmc_fcn_cmd(struct irdma_sc_dev *dev,
+				 struct irdma_hmc_fcn_info *hmcfcninfo,
+				 u16 *pmf_idx);
+int irdma_cqp_query_fpm_val_cmd(struct irdma_sc_dev *dev,
+				struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
+int irdma_cqp_commit_fpm_val_cmd(struct irdma_sc_dev *dev,
+				 struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
+int irdma_alloc_query_fpm_buf(struct irdma_sc_dev *dev,
+			      struct irdma_dma_mem *mem);
 void *irdma_remove_cqp_head(struct irdma_sc_dev *dev);
 void irdma_term_modify_qp(struct irdma_sc_qp *qp, u8 next_state, u8 term,
 			  u8 term_len);
@@ -80,7 +75,7 @@
 void wr32(struct irdma_hw *hw, u32 reg, u32 val);
 u32 rd32(struct irdma_hw *hw, u32 reg);
 u64 rd64(struct irdma_hw *hw, u32 reg);
-enum irdma_status_code irdma_map_vm_page_list(struct irdma_hw *hw, void *va,
-					      dma_addr_t *pg_dma, u32 pg_cnt);
+int irdma_map_vm_page_list(struct irdma_hw *hw, void *va, dma_addr_t *pg_dma,
+			   u32 pg_cnt);
 void irdma_unmap_vm_page_list(struct irdma_hw *hw, dma_addr_t *pg_dma, u32 pg_cnt);
 #endif /* IRDMA_OSDEP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/pble.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/pble.c
@@ -1,15 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2015 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "hmc.h"
 #include "defs.h"
 #include "type.h"
 #include "protos.h"
 #include "pble.h"
 
-static enum irdma_status_code
-add_pble_prm(struct irdma_hmc_pble_rsrc *pble_rsrc);
+static int add_pble_prm(struct irdma_hmc_pble_rsrc *pble_rsrc);
 
 /**
  * irdma_destroy_pble_prm - destroy prm during module unload
@@ -25,8 +23,7 @@
 		list_del(&chunk->list);
 		if (chunk->type == PBLE_SD_PAGED)
 			irdma_pble_free_paged_mem(chunk);
-		if (chunk->bitmapbuf)
-			kfree(chunk->bitmapmem.va);
+		bitmap_free(chunk->bitmapbuf);
 		kfree(chunk->chunkmem.va);
 	}
 }
@@ -36,13 +33,12 @@
  * @dev: irdma_sc_dev struct
  * @pble_rsrc: pble resources
  */
-enum irdma_status_code
-irdma_hmc_init_pble(struct irdma_sc_dev *dev,
-		    struct irdma_hmc_pble_rsrc *pble_rsrc)
+int irdma_hmc_init_pble(struct irdma_sc_dev *dev,
+			struct irdma_hmc_pble_rsrc *pble_rsrc)
 {
 	struct irdma_hmc_info *hmc_info;
 	u32 fpm_idx = 0;
-	enum irdma_status_code status = 0;
+	int status = 0;
 
 	hmc_info = dev->hmc_info;
 	pble_rsrc->dev = dev;
@@ -61,7 +57,7 @@
 	INIT_LIST_HEAD(&pble_rsrc->pinfo.clist);
 	if (add_pble_prm(pble_rsrc)) {
 		irdma_destroy_pble_prm(pble_rsrc);
-		status = IRDMA_ERR_NO_MEMORY;
+		status = -ENOMEM;
 	}
 
 	return status;
@@ -85,12 +81,11 @@
  * @pble_rsrc: pble resource ptr
  * @info: page info for sd
  */
-static enum irdma_status_code
-add_sd_direct(struct irdma_hmc_pble_rsrc *pble_rsrc,
-	      struct irdma_add_page_info *info)
+static int add_sd_direct(struct irdma_hmc_pble_rsrc *pble_rsrc,
+			 struct irdma_add_page_info *info)
 {
 	struct irdma_sc_dev *dev = pble_rsrc->dev;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	struct sd_pd_idx *idx = &info->idx;
 	struct irdma_chunk *chunk = info->chunk;
 	struct irdma_hmc_info *hmc_info = info->hmc_info;
@@ -138,9 +133,8 @@
  * @pble_rsrc: pble resource management
  * @info: page info for sd
  */
-static enum irdma_status_code
-add_bp_pages(struct irdma_hmc_pble_rsrc *pble_rsrc,
-	     struct irdma_add_page_info *info)
+static int add_bp_pages(struct irdma_hmc_pble_rsrc *pble_rsrc,
+			struct irdma_add_page_info *info)
 {
 	struct irdma_sc_dev *dev = pble_rsrc->dev;
 	u8 *addr;
@@ -149,13 +143,13 @@
 	struct irdma_hmc_sd_entry *sd_entry = info->sd_entry;
 	struct irdma_hmc_info *hmc_info = info->hmc_info;
 	struct irdma_chunk *chunk = info->chunk;
-	enum irdma_status_code status = 0;
+	int status = 0;
 	u32 rel_pd_idx = info->idx.rel_pd_idx;
 	u32 pd_idx = info->idx.pd_idx;
 	u32 i;
 
 	if (irdma_pble_get_paged_mem(chunk, info->pages))
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	status = irdma_add_sd_table_entry(dev->hw, hmc_info, info->idx.sd_idx,
 					  IRDMA_SD_TYPE_PAGED,
@@ -208,8 +202,7 @@
  * add_pble_prm - add a sd entry for pble resoure
  * @pble_rsrc: pble resource management
  */
-static enum irdma_status_code
-add_pble_prm(struct irdma_hmc_pble_rsrc *pble_rsrc)
+static int add_pble_prm(struct irdma_hmc_pble_rsrc *pble_rsrc)
 {
 	struct irdma_sc_dev *dev = pble_rsrc->dev;
 	struct irdma_hmc_sd_entry *sd_entry;
@@ -217,22 +210,22 @@
 	struct irdma_chunk *chunk;
 	struct irdma_add_page_info info;
 	struct sd_pd_idx *idx = &info.idx;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	enum irdma_sd_entry_type sd_entry_type;
 	u64 sd_reg_val = 0;
 	struct irdma_virt_mem chunkmem;
 	u32 pages;
 
 	if (pble_rsrc->unallocated_pble < PBLE_PER_PAGE)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	if (pble_rsrc->next_fpm_addr & 0xfff)
-		return IRDMA_ERR_INVALID_PAGE_DESC_INDEX;
+		return -EINVAL;
 
 	chunkmem.size = sizeof(*chunk);
 	chunkmem.va = kzalloc(chunkmem.size, GFP_KERNEL);
 	if (!chunkmem.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	chunk = chunkmem.va;
 	chunk->chunkmem = chunkmem;
@@ -283,7 +276,6 @@
 		  "PBLE: next_fpm_addr = %llx chunk_size[%llu] = 0x%llx\n",
 		  pble_rsrc->next_fpm_addr, chunk->size, chunk->size);
 	pble_rsrc->unallocated_pble -= (u32)(chunk->size >> 3);
-	list_add(&chunk->list, &pble_rsrc->pinfo.clist);
 	sd_reg_val = (sd_entry_type == IRDMA_SD_TYPE_PAGED) ?
 			     sd_entry->u.pd_table.pd_page_addr.pa :
 			     sd_entry->u.bp.addr.pa;
@@ -295,12 +287,12 @@
 			goto error;
 	}
 
+	list_add(&chunk->list, &pble_rsrc->pinfo.clist);
 	sd_entry->valid = true;
 	return 0;
 
 error:
-	if (chunk->bitmapbuf)
-		kfree(chunk->bitmapmem.va);
+	bitmap_free(chunk->bitmapbuf);
 	kfree(chunk->chunkmem.va);
 
 	return ret_code;
@@ -339,9 +331,8 @@
  * @pble_rsrc: pble resource management
  * @palloc: level 2 pble allocation
  */
-static enum irdma_status_code
-get_lvl2_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
-	      struct irdma_pble_alloc *palloc)
+static int get_lvl2_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
+			 struct irdma_pble_alloc *palloc)
 {
 	u32 lf4k, lflast, total, i;
 	u32 pblcnt = PBLE_PER_PAGE;
@@ -349,7 +340,7 @@
 	struct irdma_pble_level2 *lvl2 = &palloc->level2;
 	struct irdma_pble_info *root = &lvl2->root;
 	struct irdma_pble_info *leaf;
-	enum irdma_status_code ret_code;
+	int ret_code;
 	u64 fpm_addr;
 
 	/* number of full 512 (4K) leafs) */
@@ -361,7 +352,7 @@
 	lvl2->leafmem.size = (sizeof(*leaf) * total);
 	lvl2->leafmem.va = kzalloc(lvl2->leafmem.size, GFP_KERNEL);
 	if (!lvl2->leafmem.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	lvl2->leaf = lvl2->leafmem.va;
 	leaf = lvl2->leaf;
@@ -370,7 +361,7 @@
 	if (ret_code) {
 		kfree(lvl2->leafmem.va);
 		lvl2->leaf = NULL;
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 
 	root->idx = fpm_to_idx(pble_rsrc, fpm_addr);
@@ -399,7 +390,7 @@
 error:
 	free_lvl2(pble_rsrc, palloc);
 
-	return IRDMA_ERR_NO_MEMORY;
+	return -ENOMEM;
 }
 
 /**
@@ -407,11 +398,10 @@
  * @pble_rsrc: pble resource management
  * @palloc: level 1 pble allocation
  */
-static enum irdma_status_code
-get_lvl1_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
-	      struct irdma_pble_alloc *palloc)
+static int get_lvl1_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
+			 struct irdma_pble_alloc *palloc)
 {
-	enum irdma_status_code ret_code;
+	int ret_code;
 	u64 fpm_addr;
 	struct irdma_pble_info *lvl1 = &palloc->level1;
 
@@ -419,7 +409,7 @@
 				       palloc->total_cnt << 3, &lvl1->addr,
 				       &fpm_addr);
 	if (ret_code)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	palloc->level = PBLE_LEVEL_1;
 	lvl1->idx = fpm_to_idx(pble_rsrc, fpm_addr);
@@ -435,11 +425,10 @@
  * @palloc: contains all inforamtion regarding pble (idx + pble addr)
  * @level1_only: flag for a level 1 PBLE
  */
-static enum irdma_status_code
-get_lvl1_lvl2_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
-		   struct irdma_pble_alloc *palloc, bool level1_only)
+static int get_lvl1_lvl2_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
+			      struct irdma_pble_alloc *palloc, bool level1_only)
 {
-	enum irdma_status_code status = 0;
+	int status = 0;
 
 	status = get_lvl1_pble(pble_rsrc, palloc);
 	if (!status || level1_only || palloc->total_cnt <= PBLE_PER_PAGE)
@@ -457,11 +446,11 @@
  * @pble_cnt: #of pbles requested
  * @level1_only: true if only pble level 1 to acquire
  */
-enum irdma_status_code irdma_get_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
-				      struct irdma_pble_alloc *palloc,
-				      u32 pble_cnt, bool level1_only)
+int irdma_get_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
+		   struct irdma_pble_alloc *palloc, u32 pble_cnt,
+		   bool level1_only)
 {
-	enum irdma_status_code status = 0;
+	int status = 0;
 	int max_sds = 0;
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/pble.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/pble.h
@@ -78,7 +78,6 @@
 	u32 pg_cnt;
 	enum irdma_alloc_type type;
 	struct irdma_sc_dev *dev;
-	struct irdma_virt_mem bitmapmem;
 	struct irdma_virt_mem chunkmem;
 };
 
@@ -109,20 +108,18 @@
 };
 
 void irdma_destroy_pble_prm(struct irdma_hmc_pble_rsrc *pble_rsrc);
-enum irdma_status_code
-irdma_hmc_init_pble(struct irdma_sc_dev *dev,
-		    struct irdma_hmc_pble_rsrc *pble_rsrc);
+int irdma_hmc_init_pble(struct irdma_sc_dev *dev,
+			struct irdma_hmc_pble_rsrc *pble_rsrc);
 void irdma_free_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
 		     struct irdma_pble_alloc *palloc);
-enum irdma_status_code irdma_get_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
-				      struct irdma_pble_alloc *palloc,
-				      u32 pble_cnt, bool level1_only);
-enum irdma_status_code irdma_prm_add_pble_mem(struct irdma_pble_prm *pprm,
-					      struct irdma_chunk *pchunk);
-enum irdma_status_code
-irdma_prm_get_pbles(struct irdma_pble_prm *pprm,
-		    struct irdma_pble_chunkinfo *chunkinfo, u64 mem_size,
-		    u64 **vaddr, u64 *fpm_addr);
+int irdma_get_pble(struct irdma_hmc_pble_rsrc *pble_rsrc,
+		   struct irdma_pble_alloc *palloc, u32 pble_cnt,
+		   bool level1_only);
+int irdma_prm_add_pble_mem(struct irdma_pble_prm *pprm,
+			   struct irdma_chunk *pchunk);
+int irdma_prm_get_pbles(struct irdma_pble_prm *pprm,
+			struct irdma_pble_chunkinfo *chunkinfo, u64 mem_size,
+			u64 **vaddr, u64 *fpm_addr);
 void irdma_prm_return_pbles(struct irdma_pble_prm *pprm,
 			    struct irdma_pble_chunkinfo *chunkinfo);
 void irdma_pble_acquire_lock(struct irdma_hmc_pble_rsrc *pble_rsrc,
@@ -130,7 +127,6 @@
 void irdma_pble_release_lock(struct irdma_hmc_pble_rsrc *pble_rsrc,
 			     unsigned long *flags);
 void irdma_pble_free_paged_mem(struct irdma_chunk *chunk);
-enum irdma_status_code irdma_pble_get_paged_mem(struct irdma_chunk *chunk,
-						u32 pg_cnt);
+int irdma_pble_get_paged_mem(struct irdma_chunk *chunk, u32 pg_cnt);
 void irdma_prm_rem_bitmapmem(struct irdma_hw *hw, struct irdma_chunk *chunk);
 #endif /* IRDMA_PBLE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/protos.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/protos.h
@@ -12,60 +12,51 @@
 #define CQP_TIMEOUT_THRESHOLD	500
 
 /* init operations */
-enum irdma_status_code irdma_sc_dev_init(enum irdma_vers ver,
-					 struct irdma_sc_dev *dev,
-					 struct irdma_device_init_info *info);
+int irdma_sc_dev_init(enum irdma_vers ver, struct irdma_sc_dev *dev,
+		      struct irdma_device_init_info *info);
 void irdma_sc_rt_init(struct irdma_sc_dev *dev);
 void irdma_sc_cqp_post_sq(struct irdma_sc_cqp *cqp);
 __le64 *irdma_sc_cqp_get_next_send_wqe(struct irdma_sc_cqp *cqp, u64 scratch);
-enum irdma_status_code
-irdma_sc_mr_fast_register(struct irdma_sc_qp *qp,
-			  struct irdma_fast_reg_stag_info *info, bool post_sq);
+int irdma_sc_mr_fast_register(struct irdma_sc_qp *qp,
+			      struct irdma_fast_reg_stag_info *info,
+			      bool post_sq);
 /* HMC/FPM functions */
-enum irdma_status_code irdma_sc_init_iw_hmc(struct irdma_sc_dev *dev,
-					    u8 hmc_fn_id);
+int irdma_sc_init_iw_hmc(struct irdma_sc_dev *dev, u8 hmc_fn_id);
 /* stats misc */
-enum irdma_status_code
-irdma_cqp_gather_stats_cmd(struct irdma_sc_dev *dev,
-			   struct irdma_vsi_pestat *pestat, bool wait);
+int irdma_cqp_gather_stats_cmd(struct irdma_sc_dev *dev,
+			       struct irdma_vsi_pestat *pestat, bool wait);
 void irdma_cqp_gather_stats_gen1(struct irdma_sc_dev *dev,
 				 struct irdma_vsi_pestat *pestat);
 void irdma_hw_stats_read_all(struct irdma_vsi_pestat *stats,
 			     struct irdma_dev_hw_stats *stats_values,
 			     u64 *hw_stats_regs_32, u64 *hw_stats_regs_64,
 			     u8 hw_rev);
-enum irdma_status_code
-irdma_cqp_ws_node_cmd(struct irdma_sc_dev *dev, u8 cmd,
-		      struct irdma_ws_node_info *node_info);
-enum irdma_status_code irdma_cqp_up_map_cmd(struct irdma_sc_dev *dev, u8 cmd,
-					    struct irdma_up_info *map_info);
-enum irdma_status_code irdma_cqp_ceq_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_sc_ceq *sc_ceq, u8 op);
-enum irdma_status_code irdma_cqp_aeq_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_sc_aeq *sc_aeq, u8 op);
-enum irdma_status_code
-irdma_cqp_stats_inst_cmd(struct irdma_sc_vsi *vsi, u8 cmd,
-			 struct irdma_stats_inst_info *stats_info);
+int irdma_cqp_ws_node_cmd(struct irdma_sc_dev *dev, u8 cmd,
+			  struct irdma_ws_node_info *node_info);
+int irdma_cqp_ceq_cmd(struct irdma_sc_dev *dev, struct irdma_sc_ceq *sc_ceq,
+		      u8 op);
+int irdma_cqp_aeq_cmd(struct irdma_sc_dev *dev, struct irdma_sc_aeq *sc_aeq,
+		      u8 op);
+int irdma_cqp_stats_inst_cmd(struct irdma_sc_vsi *vsi, u8 cmd,
+			     struct irdma_stats_inst_info *stats_info);
 u16 irdma_alloc_ws_node_id(struct irdma_sc_dev *dev);
 void irdma_free_ws_node_id(struct irdma_sc_dev *dev, u16 node_id);
 void irdma_update_stats(struct irdma_dev_hw_stats *hw_stats,
 			struct irdma_gather_stats *gather_stats,
 			struct irdma_gather_stats *last_gather_stats);
 /* vsi functions */
-enum irdma_status_code irdma_vsi_stats_init(struct irdma_sc_vsi *vsi,
-					    struct irdma_vsi_stats_info *info);
+int irdma_vsi_stats_init(struct irdma_sc_vsi *vsi,
+			 struct irdma_vsi_stats_info *info);
 void irdma_vsi_stats_free(struct irdma_sc_vsi *vsi);
 void irdma_sc_vsi_init(struct irdma_sc_vsi *vsi,
 		       struct irdma_vsi_init_info *info);
-enum irdma_status_code irdma_sc_add_cq_ctx(struct irdma_sc_ceq *ceq,
-					   struct irdma_sc_cq *cq);
+int irdma_sc_add_cq_ctx(struct irdma_sc_ceq *ceq, struct irdma_sc_cq *cq);
 void irdma_sc_remove_cq_ctx(struct irdma_sc_ceq *ceq, struct irdma_sc_cq *cq);
 /* misc L2 param change functions */
 void irdma_change_l2params(struct irdma_sc_vsi *vsi,
 			   struct irdma_l2params *l2params);
 void irdma_sc_suspend_resume_qps(struct irdma_sc_vsi *vsi, u8 suspend);
-enum irdma_status_code irdma_cqp_qp_suspend_resume(struct irdma_sc_qp *qp,
-						   u8 cmd);
+int irdma_cqp_qp_suspend_resume(struct irdma_sc_qp *qp, u8 cmd);
 void irdma_qp_add_qos(struct irdma_sc_qp *qp);
 void irdma_qp_rem_qos(struct irdma_sc_qp *qp);
 struct irdma_sc_qp *irdma_get_qp_from_list(struct list_head *head,
@@ -83,31 +74,26 @@
 /* misc */
 u8 irdma_get_encoded_wqe_size(u32 wqsize, enum irdma_queue_type queue_type);
 void irdma_modify_qp_to_err(struct irdma_sc_qp *sc_qp);
-enum irdma_status_code
-irdma_sc_static_hmc_pages_allocated(struct irdma_sc_cqp *cqp, u64 scratch,
-				    u8 hmc_fn_id, bool post_sq,
-				    bool poll_registers);
-enum irdma_status_code irdma_cfg_fpm_val(struct irdma_sc_dev *dev,
-					 u32 qp_count);
-enum irdma_status_code irdma_get_rdma_features(struct irdma_sc_dev *dev);
+int irdma_sc_static_hmc_pages_allocated(struct irdma_sc_cqp *cqp, u64 scratch,
+					u8 hmc_fn_id, bool post_sq,
+					bool poll_registers);
+int irdma_cfg_fpm_val(struct irdma_sc_dev *dev, u32 qp_count);
+int irdma_get_rdma_features(struct irdma_sc_dev *dev);
 void free_sd_mem(struct irdma_sc_dev *dev);
-enum irdma_status_code irdma_process_cqp_cmd(struct irdma_sc_dev *dev,
-					     struct cqp_cmds_info *pcmdinfo);
-enum irdma_status_code irdma_process_bh(struct irdma_sc_dev *dev);
-enum irdma_status_code irdma_cqp_sds_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_update_sds_info *info);
-enum irdma_status_code
-irdma_cqp_query_fpm_val_cmd(struct irdma_sc_dev *dev,
-			    struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
-enum irdma_status_code
-irdma_cqp_commit_fpm_val_cmd(struct irdma_sc_dev *dev,
-			     struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
-enum irdma_status_code irdma_alloc_query_fpm_buf(struct irdma_sc_dev *dev,
-						 struct irdma_dma_mem *mem);
-enum irdma_status_code
-irdma_cqp_manage_hmc_fcn_cmd(struct irdma_sc_dev *dev,
-			     struct irdma_hmc_fcn_info *hmcfcninfo,
-			     u16 *pmf_idx);
+int irdma_process_cqp_cmd(struct irdma_sc_dev *dev,
+			  struct cqp_cmds_info *pcmdinfo);
+int irdma_process_bh(struct irdma_sc_dev *dev);
+int irdma_cqp_sds_cmd(struct irdma_sc_dev *dev,
+		      struct irdma_update_sds_info *info);
+int irdma_cqp_query_fpm_val_cmd(struct irdma_sc_dev *dev,
+				struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
+int irdma_cqp_commit_fpm_val_cmd(struct irdma_sc_dev *dev,
+				 struct irdma_dma_mem *val_mem, u8 hmc_fn_id);
+int irdma_alloc_query_fpm_buf(struct irdma_sc_dev *dev,
+			      struct irdma_dma_mem *mem);
+int irdma_cqp_manage_hmc_fcn_cmd(struct irdma_sc_dev *dev,
+				 struct irdma_hmc_fcn_info *hmcfcninfo,
+				 u16 *pmf_idx);
 void irdma_add_dev_ref(struct irdma_sc_dev *dev);
 void irdma_put_dev_ref(struct irdma_sc_dev *dev);
 void *irdma_remove_cqp_head(struct irdma_sc_dev *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/puda.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/puda.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2015 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "hmc.h"
 #include "defs.h"
 #include "type.h"
@@ -114,8 +113,7 @@
  * @rsrc: resource to use for buffer
  * @initial: flag if during init time
  */
-static enum irdma_status_code
-irdma_puda_replenish_rq(struct irdma_puda_rsrc *rsrc, bool initial)
+static int irdma_puda_replenish_rq(struct irdma_puda_rsrc *rsrc, bool initial)
 {
 	u32 i;
 	u32 invalid_cnt = rsrc->rxq_invalid_cnt;
@@ -124,7 +122,7 @@
 	for (i = 0; i < invalid_cnt; i++) {
 		buf = irdma_puda_get_bufpool(rsrc);
 		if (!buf)
-			return IRDMA_ERR_list_empty;
+			return -ENOBUFS;
 		irdma_puda_post_recvbuf(rsrc, rsrc->rx_wqe_idx, buf, initial);
 		rsrc->rx_wqe_idx = ((rsrc->rx_wqe_idx + 1) % rsrc->rq_size);
 		rsrc->rxq_invalid_cnt--;
@@ -194,7 +192,7 @@
 					    u32 *wqe_idx)
 {
 	__le64 *wqe = NULL;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	*wqe_idx = IRDMA_RING_CURRENT_HEAD(qp->sq_ring);
 	if (!*wqe_idx)
@@ -213,8 +211,8 @@
  * @cq: cq for poll
  * @info: info return for successful completion
  */
-static enum irdma_status_code
-irdma_puda_poll_info(struct irdma_sc_cq *cq, struct irdma_puda_cmpl_info *info)
+static int irdma_puda_poll_info(struct irdma_sc_cq *cq,
+				struct irdma_puda_cmpl_info *info)
 {
 	struct irdma_cq_uk *cq_uk = &cq->cq_uk;
 	u64 qword0, qword2, qword3, qword6;
@@ -233,7 +231,10 @@
 	get_64bit_val(cqe, 24, &qword3);
 	valid_bit = (bool)FIELD_GET(IRDMA_CQ_VALID, qword3);
 	if (valid_bit != cq_uk->polarity)
-		return IRDMA_ERR_Q_EMPTY;
+		return -ENOENT;
+
+	/* Ensure CQE contents are read after valid bit is checked */
+	dma_rmb();
 
 	if (cq->dev->hw_attrs.uk_attrs.hw_rev >= IRDMA_GEN_2)
 		ext_valid = (bool)FIELD_GET(IRDMA_CQ_EXTCQE, qword3);
@@ -246,7 +247,10 @@
 		if (!peek_head)
 			polarity ^= 1;
 		if (polarity != cq_uk->polarity)
-			return IRDMA_ERR_Q_EMPTY;
+			return -ENOENT;
+
+		/* Ensure ext CQE contents are read after ext valid bit is checked */
+		dma_rmb();
 
 		IRDMA_RING_MOVE_HEAD_NOCHECK(cq_uk->cq_ring);
 		if (!IRDMA_RING_CURRENT_HEAD(cq_uk->cq_ring))
@@ -267,7 +271,7 @@
 		major_err = (u32)(FIELD_GET(IRDMA_CQ_MAJERR, qword3));
 		minor_err = (u32)(FIELD_GET(IRDMA_CQ_MINERR, qword3));
 		info->compl_error = major_err << 16 | minor_err;
-		return IRDMA_ERR_CQ_COMPL_ERROR;
+		return -EIO;
 	}
 
 	get_64bit_val(cqe, 0, &qword0);
@@ -319,14 +323,13 @@
  * @cq: cq getting interrupt
  * @compl_err: return any completion err
  */
-enum irdma_status_code irdma_puda_poll_cmpl(struct irdma_sc_dev *dev,
-					    struct irdma_sc_cq *cq,
-					    u32 *compl_err)
+int irdma_puda_poll_cmpl(struct irdma_sc_dev *dev, struct irdma_sc_cq *cq,
+			 u32 *compl_err)
 {
 	struct irdma_qp_uk *qp;
 	struct irdma_cq_uk *cq_uk = &cq->cq_uk;
 	struct irdma_puda_cmpl_info info = {};
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 	struct irdma_puda_buf *buf;
 	struct irdma_puda_rsrc *rsrc;
 	u8 cq_type = cq->cq_type;
@@ -337,24 +340,24 @@
 							cq->vsi->ieq;
 	} else {
 		ibdev_dbg(to_ibdev(dev), "PUDA: qp_type error\n");
-		return IRDMA_ERR_BAD_PTR;
+		return -EINVAL;
 	}
 
 	ret = irdma_puda_poll_info(cq, &info);
 	*compl_err = info.compl_error;
-	if (ret == IRDMA_ERR_Q_EMPTY)
+	if (ret == -ENOENT)
 		return ret;
 	if (ret)
 		goto done;
 
 	qp = info.qp;
 	if (!qp || !rsrc) {
-		ret = IRDMA_ERR_BAD_PTR;
+		ret = -EFAULT;
 		goto done;
 	}
 
 	if (qp->qp_id != rsrc->qp_id) {
-		ret = IRDMA_ERR_BAD_PTR;
+		ret = -EFAULT;
 		goto done;
 	}
 
@@ -422,8 +425,7 @@
  * @qp: puda qp for send
  * @info: buffer information for transmit
  */
-enum irdma_status_code irdma_puda_send(struct irdma_sc_qp *qp,
-				       struct irdma_puda_send_info *info)
+int irdma_puda_send(struct irdma_sc_qp *qp, struct irdma_puda_send_info *info)
 {
 	__le64 *wqe;
 	u32 iplen, l4len;
@@ -443,7 +445,7 @@
 
 	wqe = irdma_puda_get_next_send_wqe(&qp->qp_uk, &wqe_idx);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	qp->qp_uk.sq_wrtrk_array[wqe_idx].wrid = (uintptr_t)info->scratch;
 	/* Third line of WQE descriptor */
@@ -503,7 +505,7 @@
 			 struct irdma_puda_buf *buf)
 {
 	struct irdma_puda_send_info info;
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 	unsigned long flags;
 
 	spin_lock_irqsave(&rsrc->bufpool_lock, flags);
@@ -603,19 +605,18 @@
  * @dev: Device
  * @qp: Resource qp
  */
-static enum irdma_status_code irdma_puda_qp_wqe(struct irdma_sc_dev *dev,
-						struct irdma_sc_qp *qp)
+static int irdma_puda_qp_wqe(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp)
 {
 	struct irdma_sc_cqp *cqp;
 	__le64 *wqe;
 	u64 hdr;
 	struct irdma_ccq_cqe_info compl_info;
-	enum irdma_status_code status = 0;
+	int status = 0;
 
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, 0);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 16, qp->hw_host_ctx_pa);
 	set_64bit_val(wqe, 40, qp->shadow_area_pa);
@@ -643,11 +644,11 @@
  * irdma_puda_qp_create - create qp for resource
  * @rsrc: resource to use for buffer
  */
-static enum irdma_status_code irdma_puda_qp_create(struct irdma_puda_rsrc *rsrc)
+static int irdma_puda_qp_create(struct irdma_puda_rsrc *rsrc)
 {
 	struct irdma_sc_qp *qp = &rsrc->qp;
 	struct irdma_qp_uk *ukqp = &qp->qp_uk;
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 	u32 sq_size, rq_size;
 	struct irdma_dma_mem *mem;
 
@@ -659,7 +660,7 @@
 					    rsrc->qpmem.size, &rsrc->qpmem.pa,
 					    GFP_KERNEL);
 	if (!rsrc->qpmem.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	mem = &rsrc->qpmem;
 	memset(mem->va, 0, rsrc->qpmem.size);
@@ -722,19 +723,18 @@
  * @dev: Device
  * @cq: resource for cq
  */
-static enum irdma_status_code irdma_puda_cq_wqe(struct irdma_sc_dev *dev,
-						struct irdma_sc_cq *cq)
+static int irdma_puda_cq_wqe(struct irdma_sc_dev *dev, struct irdma_sc_cq *cq)
 {
 	__le64 *wqe;
 	struct irdma_sc_cqp *cqp;
 	u64 hdr;
 	struct irdma_ccq_cqe_info compl_info;
-	enum irdma_status_code status = 0;
+	int status = 0;
 
 	cqp = dev->cqp;
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, 0);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 0, cq->cq_uk.cq_size);
 	set_64bit_val(wqe, 8, (uintptr_t)cq >> 1);
@@ -775,11 +775,11 @@
  * irdma_puda_cq_create - create cq for resource
  * @rsrc: resource for which cq to create
  */
-static enum irdma_status_code irdma_puda_cq_create(struct irdma_puda_rsrc *rsrc)
+static int irdma_puda_cq_create(struct irdma_puda_rsrc *rsrc)
 {
 	struct irdma_sc_dev *dev = rsrc->dev;
 	struct irdma_sc_cq *cq = &rsrc->cq;
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 	u32 cqsize;
 	struct irdma_dma_mem *mem;
 	struct irdma_cq_init_info info = {};
@@ -792,7 +792,7 @@
 	rsrc->cqmem.va = dma_alloc_coherent(dev->hw->device, rsrc->cqmem.size,
 					    &rsrc->cqmem.pa, GFP_KERNEL);
 	if (!rsrc->cqmem.va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	mem = &rsrc->cqmem;
 	info.dev = dev;
@@ -833,7 +833,7 @@
  */
 static void irdma_puda_free_qp(struct irdma_puda_rsrc *rsrc)
 {
-	enum irdma_status_code ret;
+	int ret;
 	struct irdma_ccq_cqe_info compl_info;
 	struct irdma_sc_dev *dev = rsrc->dev;
 
@@ -865,7 +865,7 @@
  */
 static void irdma_puda_free_cq(struct irdma_puda_rsrc *rsrc)
 {
-	enum irdma_status_code ret;
+	int ret;
 	struct irdma_ccq_cqe_info compl_info;
 	struct irdma_sc_dev *dev = rsrc->dev;
 
@@ -967,8 +967,7 @@
  * @rsrc: resource for buffer allocation
  * @count: number of buffers to create
  */
-static enum irdma_status_code irdma_puda_allocbufs(struct irdma_puda_rsrc *rsrc,
-						   u32 count)
+static int irdma_puda_allocbufs(struct irdma_puda_rsrc *rsrc, u32 count)
 {
 	u32 i;
 	struct irdma_puda_buf *buf;
@@ -978,7 +977,7 @@
 		buf = irdma_puda_alloc_buf(rsrc->dev, rsrc->buf_size);
 		if (!buf) {
 			rsrc->stats_buf_alloc_fail++;
-			return IRDMA_ERR_NO_MEMORY;
+			return -ENOMEM;
 		}
 		irdma_puda_ret_bufpool(rsrc, buf);
 		rsrc->alloc_buf_count++;
@@ -1001,11 +1000,11 @@
  * @vsi: sc VSI struct
  * @info: resource information
  */
-enum irdma_status_code irdma_puda_create_rsrc(struct irdma_sc_vsi *vsi,
-					      struct irdma_puda_rsrc_info *info)
+int irdma_puda_create_rsrc(struct irdma_sc_vsi *vsi,
+			   struct irdma_puda_rsrc_info *info)
 {
 	struct irdma_sc_dev *dev = vsi->dev;
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 	struct irdma_puda_rsrc *rsrc;
 	u32 pudasize;
 	u32 sqwridsize, rqwridsize;
@@ -1023,12 +1022,12 @@
 		vmem = &vsi->ieq_mem;
 		break;
 	default:
-		return IRDMA_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 	vmem->size = pudasize + sqwridsize + rqwridsize;
 	vmem->va = kzalloc(vmem->size, GFP_KERNEL);
 	if (!vmem->va)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	rsrc = vmem->va;
 	spin_lock_init(&rsrc->bufpool_lock);
@@ -1046,7 +1045,7 @@
 		rsrc->xmit_complete = irdma_ieq_tx_compl;
 		break;
 	default:
-		return IRDMA_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 
 	rsrc->type = info->type;
@@ -1323,12 +1322,12 @@
  * @buf: first receive buffer
  * @fpdu_len: total length of fpdu
  */
-static enum irdma_status_code
-irdma_ieq_create_pbufl(struct irdma_pfpdu *pfpdu, struct list_head *rxlist,
-		       struct list_head *pbufl, struct irdma_puda_buf *buf,
-		       u16 fpdu_len)
+static int irdma_ieq_create_pbufl(struct irdma_pfpdu *pfpdu,
+				  struct list_head *rxlist,
+				  struct list_head *pbufl,
+				  struct irdma_puda_buf *buf, u16 fpdu_len)
 {
-	enum irdma_status_code status = 0;
+	int status = 0;
 	struct irdma_puda_buf *nextbuf;
 	u32 nextseqnum;
 	u16 plen = fpdu_len - buf->datalen;
@@ -1338,13 +1337,13 @@
 	do {
 		nextbuf = irdma_puda_get_listbuf(rxlist);
 		if (!nextbuf) {
-			status = IRDMA_ERR_list_empty;
+			status = -ENOBUFS;
 			break;
 		}
 		list_add_tail(&nextbuf->list, pbufl);
 		if (nextbuf->seqnum != nextseqnum) {
 			pfpdu->bad_seq_num++;
-			status = IRDMA_ERR_SEQ_NUM;
+			status = -ERANGE;
 			break;
 		}
 		if (nextbuf->datalen >= plen) {
@@ -1366,11 +1365,11 @@
  * @buf: receive buffer
  * @fpdu_len: fpdu len in the buffer
  */
-static enum irdma_status_code
-irdma_ieq_handle_partial(struct irdma_puda_rsrc *ieq, struct irdma_pfpdu *pfpdu,
-			 struct irdma_puda_buf *buf, u16 fpdu_len)
+static int irdma_ieq_handle_partial(struct irdma_puda_rsrc *ieq,
+				    struct irdma_pfpdu *pfpdu,
+				    struct irdma_puda_buf *buf, u16 fpdu_len)
 {
-	enum irdma_status_code status = 0;
+	int status = 0;
 	u8 *crcptr;
 	u32 mpacrc;
 	u32 seqnum = buf->seqnum;
@@ -1390,7 +1389,7 @@
 	txbuf = irdma_puda_get_bufpool(ieq);
 	if (!txbuf) {
 		pfpdu->no_tx_bufs++;
-		status = IRDMA_ERR_NO_TXBUFS;
+		status = -ENOBUFS;
 		goto error;
 	}
 
@@ -1434,9 +1433,9 @@
  * @pfpdu: partial management per user qp
  * @buf: receive buffer
  */
-static enum irdma_status_code irdma_ieq_process_buf(struct irdma_puda_rsrc *ieq,
-						    struct irdma_pfpdu *pfpdu,
-						    struct irdma_puda_buf *buf)
+static int irdma_ieq_process_buf(struct irdma_puda_rsrc *ieq,
+				 struct irdma_pfpdu *pfpdu,
+				 struct irdma_puda_buf *buf)
 {
 	u16 fpdu_len = 0;
 	u16 datalen = buf->datalen;
@@ -1450,7 +1449,7 @@
 	bool partial = false;
 	struct irdma_puda_buf *txbuf;
 	struct list_head *rxlist = &pfpdu->rxlist;
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 
 	ioffset = (u16)(buf->data - (u8 *)buf->mem.va);
 	while (datalen) {
@@ -1459,7 +1458,7 @@
 			ibdev_dbg(to_ibdev(ieq->dev),
 				  "IEQ: error bad fpdu len\n");
 			list_add(&buf->list, rxlist);
-			return IRDMA_ERR_MPA_CRC;
+			return -EINVAL;
 		}
 
 		if (datalen < fpdu_len) {
@@ -1475,7 +1474,7 @@
 			list_add(&buf->list, rxlist);
 			ibdev_dbg(to_ibdev(ieq->dev),
 				  "ERR: IRDMA_ERR_MPA_CRC\n");
-			return IRDMA_ERR_MPA_CRC;
+			return -EINVAL;
 		}
 		full++;
 		pfpdu->fpdu_processed++;
@@ -1490,7 +1489,7 @@
 		if (!txbuf) {
 			pfpdu->no_tx_bufs++;
 			list_add(&buf->list, rxlist);
-			return IRDMA_ERR_NO_TXBUFS;
+			return -ENOBUFS;
 		}
 		/* modify txbuf's buffer header */
 		irdma_ieq_setup_tx_buf(buf, txbuf);
@@ -1539,7 +1538,7 @@
 	struct irdma_pfpdu *pfpdu = &qp->pfpdu;
 	struct list_head *rxlist = &pfpdu->rxlist;
 	struct irdma_puda_buf *buf;
-	enum irdma_status_code status;
+	int status;
 
 	do {
 		if (list_empty(rxlist))
@@ -1557,7 +1556,7 @@
 		}
 		/* keep processing buffers from the head of the list */
 		status = irdma_ieq_process_buf(ieq, pfpdu, buf);
-		if (status == IRDMA_ERR_MPA_CRC) {
+		if (status == -EINVAL) {
 			pfpdu->mpa_crc_err = true;
 			while (!list_empty(rxlist)) {
 				buf = irdma_puda_get_listbuf(rxlist);
@@ -1576,8 +1575,7 @@
  * @qp: qp pointer
  * @buf: buf received on IEQ used to create AH
  */
-static enum irdma_status_code irdma_ieq_create_ah(struct irdma_sc_qp *qp,
-						  struct irdma_puda_buf *buf)
+static int irdma_ieq_create_ah(struct irdma_sc_qp *qp, struct irdma_puda_buf *buf)
 {
 	struct irdma_ah_info ah_info = {};
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/puda.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/puda.h
@@ -151,42 +151,33 @@
 			    struct irdma_puda_buf *buf);
 void irdma_puda_send_buf(struct irdma_puda_rsrc *rsrc,
 			 struct irdma_puda_buf *buf);
-enum irdma_status_code irdma_puda_send(struct irdma_sc_qp *qp,
-				       struct irdma_puda_send_info *info);
-enum irdma_status_code
-irdma_puda_create_rsrc(struct irdma_sc_vsi *vsi,
-		       struct irdma_puda_rsrc_info *info);
+int irdma_puda_send(struct irdma_sc_qp *qp, struct irdma_puda_send_info *info);
+int irdma_puda_create_rsrc(struct irdma_sc_vsi *vsi,
+			   struct irdma_puda_rsrc_info *info);
 void irdma_puda_dele_rsrc(struct irdma_sc_vsi *vsi, enum puda_rsrc_type type,
 			  bool reset);
-enum irdma_status_code irdma_puda_poll_cmpl(struct irdma_sc_dev *dev,
-					    struct irdma_sc_cq *cq,
-					    u32 *compl_err);
+int irdma_puda_poll_cmpl(struct irdma_sc_dev *dev, struct irdma_sc_cq *cq,
+			 u32 *compl_err);
 
 struct irdma_sc_qp *irdma_ieq_get_qp(struct irdma_sc_dev *dev,
 				     struct irdma_puda_buf *buf);
-enum irdma_status_code
-irdma_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
-			  struct irdma_puda_buf *buf);
-enum irdma_status_code irdma_ieq_check_mpacrc(struct shash_desc *desc,
-					      void *addr, u32 len, u32 val);
-enum irdma_status_code irdma_init_hash_desc(struct shash_desc **desc);
+int irdma_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
+			      struct irdma_puda_buf *buf);
+int irdma_ieq_check_mpacrc(struct shash_desc *desc, void *addr, u32 len, u32 val);
+int irdma_init_hash_desc(struct shash_desc **desc);
 void irdma_ieq_mpa_crc_ae(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp);
 void irdma_free_hash_desc(struct shash_desc *desc);
-void irdma_ieq_update_tcpip_info(struct irdma_puda_buf *buf, u16 len,
-				 u32 seqnum);
-enum irdma_status_code irdma_cqp_qp_create_cmd(struct irdma_sc_dev *dev,
-					       struct irdma_sc_qp *qp);
-enum irdma_status_code irdma_cqp_cq_create_cmd(struct irdma_sc_dev *dev,
-					       struct irdma_sc_cq *cq);
-enum irdma_status_code irdma_cqp_qp_destroy_cmd(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp);
+void irdma_ieq_update_tcpip_info(struct irdma_puda_buf *buf, u16 len, u32 seqnum);
+int irdma_cqp_qp_create_cmd(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp);
+int irdma_cqp_cq_create_cmd(struct irdma_sc_dev *dev, struct irdma_sc_cq *cq);
+int irdma_cqp_qp_destroy_cmd(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp);
 void irdma_cqp_cq_destroy_cmd(struct irdma_sc_dev *dev, struct irdma_sc_cq *cq);
 void irdma_puda_ieq_get_ah_info(struct irdma_sc_qp *qp,
 				struct irdma_ah_info *ah_info);
-enum irdma_status_code irdma_puda_create_ah(struct irdma_sc_dev *dev,
-					    struct irdma_ah_info *ah_info,
-					    bool wait, enum puda_rsrc_type type,
-					    void *cb_param,
-					    struct irdma_sc_ah **ah);
+int irdma_puda_create_ah(struct irdma_sc_dev *dev,
+			 struct irdma_ah_info *ah_info, bool wait,
+			 enum puda_rsrc_type type, void *cb_param,
+			 struct irdma_sc_ah **ah);
 void irdma_puda_free_ah(struct irdma_sc_dev *dev, struct irdma_sc_ah *ah);
 void irdma_ieq_process_fpdus(struct irdma_sc_qp *qp,
 			     struct irdma_puda_rsrc *ieq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/type.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/type.h
@@ -2,7 +2,6 @@
 /* Copyright (c) 2015 - 2021 Intel Corporation */
 #ifndef IRDMA_TYPE_H
 #define IRDMA_TYPE_H
-#include "status.h"
 #include "osdep.h"
 #include "irdma.h"
 #include "user.h"
@@ -99,6 +98,7 @@
 enum irdma_qp_event_type {
 	IRDMA_QP_EVENT_CATASTROPHIC,
 	IRDMA_QP_EVENT_ACCESS_ERR,
+	IRDMA_QP_EVENT_REQ_ERR,
 };
 
 enum irdma_hw_stats_index_32b {
@@ -402,14 +402,16 @@
 	u64 host_ctx_pa;
 	void *back_cqp;
 	struct irdma_sc_dev *dev;
-	enum irdma_status_code (*process_cqp_sds)(struct irdma_sc_dev *dev,
-						  struct irdma_update_sds_info *info);
+	int (*process_cqp_sds)(struct irdma_sc_dev *dev,
+			       struct irdma_update_sds_info *info);
 	struct irdma_dma_mem sdbuf;
 	struct irdma_ring sq_ring;
 	struct irdma_cqp_quanta *sq_base;
 	struct irdma_dcqcn_cc_params dcqcn_params;
 	__le64 *host_ctx;
 	u64 *scratch_array;
+	u64 requested_ops;
+	atomic64_t completed_ops;
 	u32 cqp_id;
 	u32 sq_size;
 	u32 hw_sq_size;
@@ -605,8 +607,8 @@
 	struct irdma_qos qos[IRDMA_MAX_USER_PRIORITY];
 	struct irdma_vsi_pestat *pestat;
 	atomic_t qp_suspend_reqs;
-	enum irdma_status_code (*register_qset)(struct irdma_sc_vsi *vsi,
-						struct irdma_ws_node *tc_node);
+	int (*register_qset)(struct irdma_sc_vsi *vsi,
+			     struct irdma_ws_node *tc_node);
 	void (*unregister_qset)(struct irdma_sc_vsi *vsi,
 				struct irdma_ws_node *tc_node);
 	u8 qos_rel_bw;
@@ -655,7 +657,7 @@
 	bool vchnl_up:1;
 	bool ceq_valid:1;
 	u8 pci_rev;
-	enum irdma_status_code (*ws_add)(struct irdma_sc_vsi *vsi, u8 user_pri);
+	int (*ws_add)(struct irdma_sc_vsi *vsi, u8 user_pri);
 	void (*ws_remove)(struct irdma_sc_vsi *vsi, u8 user_pri);
 	void (*ws_reset)(struct irdma_sc_vsi *vsi);
 };
@@ -750,8 +752,8 @@
 	u16 pf_data_vsi_num;
 	enum irdma_vm_vf_type vm_vf_type;
 	u16 vm_id;
-	enum irdma_status_code (*register_qset)(struct irdma_sc_vsi *vsi,
-						struct irdma_ws_node *tc_node);
+	int (*register_qset)(struct irdma_sc_vsi *vsi,
+			     struct irdma_ws_node *tc_node);
 	void (*unregister_qset)(struct irdma_sc_vsi *vsi,
 				struct irdma_ws_node *tc_node);
 };
@@ -1010,6 +1012,7 @@
 	bool remote_access:1;
 	bool use_hmc_fcn_index:1;
 	bool use_pf_rid:1;
+	bool all_memory:1;
 	u8 hmc_fcn_index;
 };
 
@@ -1037,6 +1040,7 @@
 	bool use_hmc_fcn_index:1;
 	u8 hmc_fcn_index;
 	bool use_pf_rid:1;
+	bool all_memory:1;
 };
 
 struct irdma_fast_reg_stag_info {
@@ -1199,29 +1203,27 @@
 };
 
 void irdma_sc_ccq_arm(struct irdma_sc_cq *ccq);
-enum irdma_status_code irdma_sc_ccq_create(struct irdma_sc_cq *ccq, u64 scratch,
-					   bool check_overflow, bool post_sq);
-enum irdma_status_code irdma_sc_ccq_destroy(struct irdma_sc_cq *ccq, u64 scratch,
-					    bool post_sq);
-enum irdma_status_code irdma_sc_ccq_get_cqe_info(struct irdma_sc_cq *ccq,
-						 struct irdma_ccq_cqe_info *info);
-enum irdma_status_code irdma_sc_ccq_init(struct irdma_sc_cq *ccq,
-					 struct irdma_ccq_init_info *info);
-
-enum irdma_status_code irdma_sc_cceq_create(struct irdma_sc_ceq *ceq, u64 scratch);
-enum irdma_status_code irdma_sc_cceq_destroy_done(struct irdma_sc_ceq *ceq);
-
-enum irdma_status_code irdma_sc_ceq_destroy(struct irdma_sc_ceq *ceq, u64 scratch,
-					    bool post_sq);
-enum irdma_status_code irdma_sc_ceq_init(struct irdma_sc_ceq *ceq,
-					 struct irdma_ceq_init_info *info);
+int irdma_sc_ccq_create(struct irdma_sc_cq *ccq, u64 scratch,
+			bool check_overflow, bool post_sq);
+int irdma_sc_ccq_destroy(struct irdma_sc_cq *ccq, u64 scratch, bool post_sq);
+int irdma_sc_ccq_get_cqe_info(struct irdma_sc_cq *ccq,
+			      struct irdma_ccq_cqe_info *info);
+int irdma_sc_ccq_init(struct irdma_sc_cq *ccq,
+		      struct irdma_ccq_init_info *info);
+
+int irdma_sc_cceq_create(struct irdma_sc_ceq *ceq, u64 scratch);
+int irdma_sc_cceq_destroy_done(struct irdma_sc_ceq *ceq);
+
+int irdma_sc_ceq_destroy(struct irdma_sc_ceq *ceq, u64 scratch, bool post_sq);
+int irdma_sc_ceq_init(struct irdma_sc_ceq *ceq,
+		      struct irdma_ceq_init_info *info);
 void irdma_sc_cleanup_ceqes(struct irdma_sc_cq *cq, struct irdma_sc_ceq *ceq);
 void *irdma_sc_process_ceq(struct irdma_sc_dev *dev, struct irdma_sc_ceq *ceq);
 
-enum irdma_status_code irdma_sc_aeq_init(struct irdma_sc_aeq *aeq,
-					 struct irdma_aeq_init_info *info);
-enum irdma_status_code irdma_sc_get_next_aeqe(struct irdma_sc_aeq *aeq,
-					      struct irdma_aeqe_info *info);
+int irdma_sc_aeq_init(struct irdma_sc_aeq *aeq,
+		      struct irdma_aeq_init_info *info);
+int irdma_sc_get_next_aeqe(struct irdma_sc_aeq *aeq,
+			   struct irdma_aeqe_info *info);
 void irdma_sc_repost_aeq_entries(struct irdma_sc_dev *dev, u32 count);
 
 void irdma_sc_pd_init(struct irdma_sc_dev *dev, struct irdma_sc_pd *pd, u32 pd_id,
@@ -1229,47 +1231,41 @@
 void irdma_cfg_aeq(struct irdma_sc_dev *dev, u32 idx, bool enable);
 void irdma_check_cqp_progress(struct irdma_cqp_timeout *cqp_timeout,
 			      struct irdma_sc_dev *dev);
-enum irdma_status_code irdma_sc_cqp_create(struct irdma_sc_cqp *cqp, u16 *maj_err,
-					   u16 *min_err);
-enum irdma_status_code irdma_sc_cqp_destroy(struct irdma_sc_cqp *cqp);
-enum irdma_status_code irdma_sc_cqp_init(struct irdma_sc_cqp *cqp,
-					 struct irdma_cqp_init_info *info);
+int irdma_sc_cqp_create(struct irdma_sc_cqp *cqp, u16 *maj_err, u16 *min_err);
+int irdma_sc_cqp_destroy(struct irdma_sc_cqp *cqp);
+int irdma_sc_cqp_init(struct irdma_sc_cqp *cqp,
+		      struct irdma_cqp_init_info *info);
 void irdma_sc_cqp_post_sq(struct irdma_sc_cqp *cqp);
-enum irdma_status_code irdma_sc_poll_for_cqp_op_done(struct irdma_sc_cqp *cqp, u8 opcode,
-						     struct irdma_ccq_cqe_info *cmpl_info);
-enum irdma_status_code irdma_sc_fast_register(struct irdma_sc_qp *qp,
-					      struct irdma_fast_reg_stag_info *info,
-					      bool post_sq);
-enum irdma_status_code irdma_sc_qp_create(struct irdma_sc_qp *qp,
-					  struct irdma_create_qp_info *info,
-					  u64 scratch, bool post_sq);
-enum irdma_status_code irdma_sc_qp_destroy(struct irdma_sc_qp *qp,
-					   u64 scratch, bool remove_hash_idx,
-					   bool ignore_mw_bnd, bool post_sq);
-enum irdma_status_code irdma_sc_qp_flush_wqes(struct irdma_sc_qp *qp,
-					      struct irdma_qp_flush_info *info,
-					      u64 scratch, bool post_sq);
-enum irdma_status_code irdma_sc_qp_init(struct irdma_sc_qp *qp,
-					struct irdma_qp_init_info *info);
-enum irdma_status_code irdma_sc_qp_modify(struct irdma_sc_qp *qp,
-					  struct irdma_modify_qp_info *info,
-					  u64 scratch, bool post_sq);
+int irdma_sc_poll_for_cqp_op_done(struct irdma_sc_cqp *cqp, u8 opcode,
+				  struct irdma_ccq_cqe_info *cmpl_info);
+int irdma_sc_fast_register(struct irdma_sc_qp *qp,
+			   struct irdma_fast_reg_stag_info *info, bool post_sq);
+int irdma_sc_qp_create(struct irdma_sc_qp *qp,
+		       struct irdma_create_qp_info *info, u64 scratch,
+		       bool post_sq);
+int irdma_sc_qp_destroy(struct irdma_sc_qp *qp, u64 scratch,
+			bool remove_hash_idx, bool ignore_mw_bnd, bool post_sq);
+int irdma_sc_qp_flush_wqes(struct irdma_sc_qp *qp,
+			   struct irdma_qp_flush_info *info, u64 scratch,
+			   bool post_sq);
+int irdma_sc_qp_init(struct irdma_sc_qp *qp, struct irdma_qp_init_info *info);
+int irdma_sc_qp_modify(struct irdma_sc_qp *qp,
+		       struct irdma_modify_qp_info *info, u64 scratch,
+		       bool post_sq);
 void irdma_sc_send_lsmm(struct irdma_sc_qp *qp, void *lsmm_buf, u32 size,
 			irdma_stag stag);
-void irdma_sc_send_lsmm_nostag(struct irdma_sc_qp *qp, void *lsmm_buf, u32 size);
+
 void irdma_sc_send_rtt(struct irdma_sc_qp *qp, bool read);
 void irdma_sc_qp_setctx(struct irdma_sc_qp *qp, __le64 *qp_ctx,
 			struct irdma_qp_host_ctx_info *info);
 void irdma_sc_qp_setctx_roce(struct irdma_sc_qp *qp, __le64 *qp_ctx,
 			     struct irdma_qp_host_ctx_info *info);
-enum irdma_status_code irdma_sc_cq_destroy(struct irdma_sc_cq *cq, u64 scratch,
-					   bool post_sq);
-enum irdma_status_code irdma_sc_cq_init(struct irdma_sc_cq *cq,
-					struct irdma_cq_init_info *info);
+int irdma_sc_cq_destroy(struct irdma_sc_cq *cq, u64 scratch, bool post_sq);
+int irdma_sc_cq_init(struct irdma_sc_cq *cq, struct irdma_cq_init_info *info);
 void irdma_sc_cq_resize(struct irdma_sc_cq *cq, struct irdma_modify_cq_info *info);
-enum irdma_status_code irdma_sc_static_hmc_pages_allocated(struct irdma_sc_cqp *cqp,
-							   u64 scratch, u8 hmc_fn_id,
-							   bool post_sq, bool poll_registers);
+int irdma_sc_static_hmc_pages_allocated(struct irdma_sc_cqp *cqp, u64 scratch,
+					u8 hmc_fn_id, bool post_sq,
+					bool poll_registers);
 
 void sc_vsi_update_stats(struct irdma_sc_vsi *vsi);
 struct cqp_info {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/uda.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/uda.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2016 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "hmc.h"
 #include "defs.h"
 #include "type.h"
@@ -16,16 +15,15 @@
  * @op: Operation
  * @scratch: u64 saved to be used during cqp completion
  */
-enum irdma_status_code irdma_sc_access_ah(struct irdma_sc_cqp *cqp,
-					  struct irdma_ah_info *info,
-					  u32 op, u64 scratch)
+int irdma_sc_access_ah(struct irdma_sc_cqp *cqp, struct irdma_ah_info *info,
+		       u32 op, u64 scratch)
 {
 	__le64 *wqe;
 	u64 qw1, qw2;
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe)
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 
 	set_64bit_val(wqe, 0, ether_addr_to_u64(info->mac_addr) << 16);
 	qw1 = FIELD_PREP(IRDMA_UDA_CQPSQ_MAV_PDINDEXLO, info->pd_idx) |
@@ -84,8 +82,7 @@
  * irdma_create_mg_ctx() - create a mcg context
  * @info: multicast group context info
  */
-static enum irdma_status_code
-irdma_create_mg_ctx(struct irdma_mcast_grp_info *info)
+static int irdma_create_mg_ctx(struct irdma_mcast_grp_info *info)
 {
 	struct irdma_mcast_grp_ctx_entry_info *entry_info = NULL;
 	u8 idx = 0; /* index in the array */
@@ -115,22 +112,22 @@
  * @op: operation to perform
  * @scratch: u64 saved to be used during cqp completion
  */
-enum irdma_status_code irdma_access_mcast_grp(struct irdma_sc_cqp *cqp,
-					      struct irdma_mcast_grp_info *info,
-					      u32 op, u64 scratch)
+int irdma_access_mcast_grp(struct irdma_sc_cqp *cqp,
+			   struct irdma_mcast_grp_info *info, u32 op,
+			   u64 scratch)
 {
 	__le64 *wqe;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	if (info->mg_id >= IRDMA_UDA_MAX_FSI_MGS) {
 		ibdev_dbg(to_ibdev(cqp->dev), "WQE: mg_id out of range\n");
-		return IRDMA_ERR_PARAM;
+		return -EINVAL;
 	}
 
 	wqe = irdma_sc_cqp_get_next_send_wqe(cqp, scratch);
 	if (!wqe) {
 		ibdev_dbg(to_ibdev(cqp->dev), "WQE: ring full\n");
-		return IRDMA_ERR_RING_FULL;
+		return -ENOMEM;
 	}
 
 	ret_code = irdma_create_mg_ctx(info);
@@ -196,8 +193,8 @@
  * @ctx: Multcast group context
  * @mg: Multcast group info
  */
-enum irdma_status_code irdma_sc_add_mcast_grp(struct irdma_mcast_grp_info *ctx,
-					      struct irdma_mcast_grp_ctx_entry_info *mg)
+int irdma_sc_add_mcast_grp(struct irdma_mcast_grp_info *ctx,
+			   struct irdma_mcast_grp_ctx_entry_info *mg)
 {
 	u32 idx;
 	bool free_entry_found = false;
@@ -226,7 +223,7 @@
 		return 0;
 	}
 
-	return IRDMA_ERR_NO_MEMORY;
+	return -ENOMEM;
 }
 
 /**
@@ -237,8 +234,8 @@
  * Finds and removes a specific mulicast group from context, all
  * parameters must match to remove a multicast group.
  */
-enum irdma_status_code irdma_sc_del_mcast_grp(struct irdma_mcast_grp_info *ctx,
-					      struct irdma_mcast_grp_ctx_entry_info *mg)
+int irdma_sc_del_mcast_grp(struct irdma_mcast_grp_info *ctx,
+			   struct irdma_mcast_grp_ctx_entry_info *mg)
 {
 	u32 idx;
 
@@ -267,5 +264,5 @@
 		}
 	}
 
-	return IRDMA_ERR_PARAM;
+	return -EINVAL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/uda.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/uda.h
@@ -32,56 +32,54 @@
 	struct irdma_ah_info ah_info;
 };
 
-enum irdma_status_code irdma_sc_add_mcast_grp(struct irdma_mcast_grp_info *ctx,
-					      struct irdma_mcast_grp_ctx_entry_info *mg);
-enum irdma_status_code irdma_sc_del_mcast_grp(struct irdma_mcast_grp_info *ctx,
-					      struct irdma_mcast_grp_ctx_entry_info *mg);
-enum irdma_status_code irdma_sc_access_ah(struct irdma_sc_cqp *cqp, struct irdma_ah_info *info,
-					  u32 op, u64 scratch);
-enum irdma_status_code irdma_access_mcast_grp(struct irdma_sc_cqp *cqp,
-					      struct irdma_mcast_grp_info *info,
-					      u32 op, u64 scratch);
+int irdma_sc_add_mcast_grp(struct irdma_mcast_grp_info *ctx,
+			   struct irdma_mcast_grp_ctx_entry_info *mg);
+int irdma_sc_del_mcast_grp(struct irdma_mcast_grp_info *ctx,
+			   struct irdma_mcast_grp_ctx_entry_info *mg);
+int irdma_sc_access_ah(struct irdma_sc_cqp *cqp, struct irdma_ah_info *info,
+		       u32 op, u64 scratch);
+int irdma_access_mcast_grp(struct irdma_sc_cqp *cqp,
+			   struct irdma_mcast_grp_info *info, u32 op,
+			   u64 scratch);
 
 static inline void irdma_sc_init_ah(struct irdma_sc_dev *dev, struct irdma_sc_ah *ah)
 {
 	ah->dev = dev;
 }
 
-static inline enum irdma_status_code irdma_sc_create_ah(struct irdma_sc_cqp *cqp,
-							struct irdma_ah_info *info,
-							u64 scratch)
+static inline int irdma_sc_create_ah(struct irdma_sc_cqp *cqp,
+				     struct irdma_ah_info *info, u64 scratch)
 {
 	return irdma_sc_access_ah(cqp, info, IRDMA_CQP_OP_CREATE_ADDR_HANDLE,
 				  scratch);
 }
 
-static inline enum irdma_status_code irdma_sc_destroy_ah(struct irdma_sc_cqp *cqp,
-							 struct irdma_ah_info *info,
-							 u64 scratch)
+static inline int irdma_sc_destroy_ah(struct irdma_sc_cqp *cqp,
+				      struct irdma_ah_info *info, u64 scratch)
 {
 	return irdma_sc_access_ah(cqp, info, IRDMA_CQP_OP_DESTROY_ADDR_HANDLE,
 				  scratch);
 }
 
-static inline enum irdma_status_code irdma_sc_create_mcast_grp(struct irdma_sc_cqp *cqp,
-							       struct irdma_mcast_grp_info *info,
-							       u64 scratch)
+static inline int irdma_sc_create_mcast_grp(struct irdma_sc_cqp *cqp,
+					    struct irdma_mcast_grp_info *info,
+					    u64 scratch)
 {
 	return irdma_access_mcast_grp(cqp, info, IRDMA_CQP_OP_CREATE_MCAST_GRP,
 				      scratch);
 }
 
-static inline enum irdma_status_code irdma_sc_modify_mcast_grp(struct irdma_sc_cqp *cqp,
-							       struct irdma_mcast_grp_info *info,
-							       u64 scratch)
+static inline int irdma_sc_modify_mcast_grp(struct irdma_sc_cqp *cqp,
+					    struct irdma_mcast_grp_info *info,
+					    u64 scratch)
 {
 	return irdma_access_mcast_grp(cqp, info, IRDMA_CQP_OP_MODIFY_MCAST_GRP,
 				      scratch);
 }
 
-static inline enum irdma_status_code irdma_sc_destroy_mcast_grp(struct irdma_sc_cqp *cqp,
-								struct irdma_mcast_grp_info *info,
-								u64 scratch)
+static inline int irdma_sc_destroy_mcast_grp(struct irdma_sc_cqp *cqp,
+					     struct irdma_mcast_grp_info *info,
+					     u64 scratch)
 {
 	return irdma_access_mcast_grp(cqp, info, IRDMA_CQP_OP_DESTROY_MCAST_GRP,
 				      scratch);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/uk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/uk.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2015 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "defs.h"
 #include "user.h"
 #include "irdma.h"
@@ -13,16 +12,16 @@
  * @sge: sge length and stag
  * @valid: The wqe valid
  */
-static void irdma_set_fragment(__le64 *wqe, u32 offset, struct irdma_sge *sge,
+static void irdma_set_fragment(__le64 *wqe, u32 offset, struct ib_sge *sge,
 			       u8 valid)
 {
 	if (sge) {
 		set_64bit_val(wqe, offset,
-			      FIELD_PREP(IRDMAQPSQ_FRAG_TO, sge->tag_off));
+			      FIELD_PREP(IRDMAQPSQ_FRAG_TO, sge->addr));
 		set_64bit_val(wqe, offset + 8,
 			      FIELD_PREP(IRDMAQPSQ_VALID, valid) |
-			      FIELD_PREP(IRDMAQPSQ_FRAG_LEN, sge->len) |
-			      FIELD_PREP(IRDMAQPSQ_FRAG_STAG, sge->stag));
+			      FIELD_PREP(IRDMAQPSQ_FRAG_LEN, sge->length) |
+			      FIELD_PREP(IRDMAQPSQ_FRAG_STAG, sge->lkey));
 	} else {
 		set_64bit_val(wqe, offset, 0);
 		set_64bit_val(wqe, offset + 8,
@@ -38,14 +37,14 @@
  * @valid: wqe valid flag
  */
 static void irdma_set_fragment_gen_1(__le64 *wqe, u32 offset,
-				     struct irdma_sge *sge, u8 valid)
+				     struct ib_sge *sge, u8 valid)
 {
 	if (sge) {
 		set_64bit_val(wqe, offset,
-			      FIELD_PREP(IRDMAQPSQ_FRAG_TO, sge->tag_off));
+			      FIELD_PREP(IRDMAQPSQ_FRAG_TO, sge->addr));
 		set_64bit_val(wqe, offset + 8,
-			      FIELD_PREP(IRDMAQPSQ_GEN1_FRAG_LEN, sge->len) |
-			      FIELD_PREP(IRDMAQPSQ_GEN1_FRAG_STAG, sge->stag));
+			      FIELD_PREP(IRDMAQPSQ_GEN1_FRAG_LEN, sge->length) |
+			      FIELD_PREP(IRDMAQPSQ_GEN1_FRAG_STAG, sge->lkey));
 	} else {
 		set_64bit_val(wqe, offset, 0);
 		set_64bit_val(wqe, offset + 8, 0);
@@ -56,7 +55,7 @@
  * irdma_nop_1 - insert a NOP wqe
  * @qp: hw qp ptr
  */
-static enum irdma_status_code irdma_nop_1(struct irdma_qp_uk *qp)
+static int irdma_nop_1(struct irdma_qp_uk *qp)
 {
 	u64 hdr;
 	__le64 *wqe;
@@ -64,7 +63,7 @@
 	bool signaled = false;
 
 	if (!qp->sq_ring.head)
-		return IRDMA_ERR_PARAM;
+		return -EINVAL;
 
 	wqe_idx = IRDMA_RING_CURRENT_HEAD(qp->sq_ring);
 	wqe = qp->sq_base[wqe_idx].elem;
@@ -94,16 +93,18 @@
  */
 void irdma_clr_wqes(struct irdma_qp_uk *qp, u32 qp_wqe_idx)
 {
-	__le64 *wqe;
+	struct irdma_qp_quanta *sq;
 	u32 wqe_idx;
 
 	if (!(qp_wqe_idx & 0x7F)) {
 		wqe_idx = (qp_wqe_idx + 128) % qp->sq_ring.size;
-		wqe = qp->sq_base[wqe_idx].elem;
+		sq = qp->sq_base + wqe_idx;
 		if (wqe_idx)
-			memset(wqe, qp->swqe_polarity ? 0 : 0xFF, 0x1000);
+			memset(sq, qp->swqe_polarity ? 0 : 0xFF,
+			       128 * sizeof(*sq));
 		else
-			memset(wqe, qp->swqe_polarity ? 0xFF : 0, 0x1000);
+			memset(sq, qp->swqe_polarity ? 0xFF : 0,
+			       128 * sizeof(*sq));
 	}
 }
 
@@ -245,7 +246,7 @@
 __le64 *irdma_qp_get_next_recv_wqe(struct irdma_qp_uk *qp, u32 *wqe_idx)
 {
 	__le64 *wqe;
-	enum irdma_status_code ret_code;
+	int ret_code;
 
 	if (IRDMA_RING_FULL_ERR(qp->rq_ring))
 		return NULL;
@@ -268,16 +269,15 @@
  * @info: post sq information
  * @post_sq: flag to post sq
  */
-enum irdma_status_code irdma_uk_rdma_write(struct irdma_qp_uk *qp,
-					   struct irdma_post_sq_info *info,
-					   bool post_sq)
+int irdma_uk_rdma_write(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
+			bool post_sq)
 {
 	u64 hdr;
 	__le64 *wqe;
 	struct irdma_rdma_write *op_info;
 	u32 i, wqe_idx;
 	u32 total_size = 0, byte_off;
-	enum irdma_status_code ret_code;
+	int ret_code;
 	u32 frag_cnt, addl_frag_cnt;
 	bool read_fence = false;
 	u16 quanta;
@@ -286,10 +286,10 @@
 
 	op_info = &info->op.rdma_write;
 	if (op_info->num_lo_sges > qp->max_sq_frag_cnt)
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 
 	for (i = 0; i < op_info->num_lo_sges; i++)
-		total_size += op_info->lo_sg_list[i].len;
+		total_size += op_info->lo_sg_list[i].length;
 
 	read_fence |= info->read_fence;
 
@@ -305,12 +305,12 @@
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, quanta, total_size,
 					 info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
 	set_64bit_val(wqe, 16,
-		      FIELD_PREP(IRDMAQPSQ_FRAG_TO, op_info->rem_addr.tag_off));
+		      FIELD_PREP(IRDMAQPSQ_FRAG_TO, op_info->rem_addr.addr));
 
 	if (info->imm_data_valid) {
 		set_64bit_val(wqe, 0,
@@ -339,7 +339,7 @@
 			++addl_frag_cnt;
 	}
 
-	hdr = FIELD_PREP(IRDMAQPSQ_REMSTAG, op_info->rem_addr.stag) |
+	hdr = FIELD_PREP(IRDMAQPSQ_REMSTAG, op_info->rem_addr.lkey) |
 	      FIELD_PREP(IRDMAQPSQ_OPCODE, info->op_type) |
 	      FIELD_PREP(IRDMAQPSQ_IMMDATAFLAG, info->imm_data_valid) |
 	      FIELD_PREP(IRDMAQPSQ_REPORTRTT, info->report_rtt) |
@@ -370,12 +370,11 @@
  * @inv_stag: flag for inv_stag
  * @post_sq: flag to post sq
  */
-enum irdma_status_code irdma_uk_rdma_read(struct irdma_qp_uk *qp,
-					  struct irdma_post_sq_info *info,
-					  bool inv_stag, bool post_sq)
+int irdma_uk_rdma_read(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
+		       bool inv_stag, bool post_sq)
 {
 	struct irdma_rdma_read *op_info;
-	enum irdma_status_code ret_code;
+	int ret_code;
 	u32 i, byte_off, total_size = 0;
 	bool local_fence = false;
 	u32 addl_frag_cnt;
@@ -388,10 +387,10 @@
 
 	op_info = &info->op.rdma_read;
 	if (qp->max_sq_frag_cnt < op_info->num_lo_sges)
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 
 	for (i = 0; i < op_info->num_lo_sges; i++)
-		total_size += op_info->lo_sg_list[i].len;
+		total_size += op_info->lo_sg_list[i].length;
 
 	ret_code = irdma_fragcnt_to_quanta_sq(op_info->num_lo_sges, &quanta);
 	if (ret_code)
@@ -400,7 +399,7 @@
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, quanta, total_size,
 					 info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
@@ -426,8 +425,8 @@
 			++addl_frag_cnt;
 	}
 	set_64bit_val(wqe, 16,
-		      FIELD_PREP(IRDMAQPSQ_FRAG_TO, op_info->rem_addr.tag_off));
-	hdr = FIELD_PREP(IRDMAQPSQ_REMSTAG, op_info->rem_addr.stag) |
+		      FIELD_PREP(IRDMAQPSQ_FRAG_TO, op_info->rem_addr.addr));
+	hdr = FIELD_PREP(IRDMAQPSQ_REMSTAG, op_info->rem_addr.lkey) |
 	      FIELD_PREP(IRDMAQPSQ_REPORTRTT, (info->report_rtt ? 1 : 0)) |
 	      FIELD_PREP(IRDMAQPSQ_ADDFRAGCNT, addl_frag_cnt) |
 	      FIELD_PREP(IRDMAQPSQ_OPCODE,
@@ -457,15 +456,14 @@
  * @info: post sq information
  * @post_sq: flag to post sq
  */
-enum irdma_status_code irdma_uk_send(struct irdma_qp_uk *qp,
-				     struct irdma_post_sq_info *info,
-				     bool post_sq)
+int irdma_uk_send(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
+		  bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_post_send *op_info;
 	u64 hdr;
 	u32 i, wqe_idx, total_size = 0, byte_off;
-	enum irdma_status_code ret_code;
+	int ret_code;
 	u32 frag_cnt, addl_frag_cnt;
 	bool read_fence = false;
 	u16 quanta;
@@ -474,10 +472,10 @@
 
 	op_info = &info->op.send;
 	if (qp->max_sq_frag_cnt < op_info->num_sges)
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 
 	for (i = 0; i < op_info->num_sges; i++)
-		total_size += op_info->sg_list[i].len;
+		total_size += op_info->sg_list[i].length;
 
 	if (info->imm_data_valid)
 		frag_cnt = op_info->num_sges + 1;
@@ -490,7 +488,7 @@
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, quanta, total_size,
 					 info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
@@ -501,7 +499,8 @@
 			      FIELD_PREP(IRDMAQPSQ_IMMDATA, info->imm_data));
 		i = 0;
 	} else {
-		qp->wqe_ops.iw_set_fragment(wqe, 0, op_info->sg_list,
+		qp->wqe_ops.iw_set_fragment(wqe, 0,
+					    frag_cnt ? op_info->sg_list : NULL,
 					    qp->swqe_polarity);
 		i = 1;
 	}
@@ -678,9 +677,8 @@
  * @info: post sq information
  * @post_sq: flag to post sq
  */
-enum irdma_status_code
-irdma_uk_inline_rdma_write(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
-			   bool post_sq)
+int irdma_uk_inline_rdma_write(struct irdma_qp_uk *qp,
+			       struct irdma_post_sq_info *info, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_inline_rdma_write *op_info;
@@ -693,21 +691,21 @@
 	op_info = &info->op.inline_rdma_write;
 
 	if (op_info->len > qp->max_inline_data)
-		return IRDMA_ERR_INVALID_INLINE_DATA_SIZE;
+		return -EINVAL;
 
 	quanta = qp->wqe_ops.iw_inline_data_size_to_quanta(op_info->len);
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, quanta, op_info->len,
 					 info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
 	read_fence |= info->read_fence;
 	set_64bit_val(wqe, 16,
-		      FIELD_PREP(IRDMAQPSQ_FRAG_TO, op_info->rem_addr.tag_off));
+		      FIELD_PREP(IRDMAQPSQ_FRAG_TO, op_info->rem_addr.addr));
 
-	hdr = FIELD_PREP(IRDMAQPSQ_REMSTAG, op_info->rem_addr.stag) |
+	hdr = FIELD_PREP(IRDMAQPSQ_REMSTAG, op_info->rem_addr.lkey) |
 	      FIELD_PREP(IRDMAQPSQ_OPCODE, info->op_type) |
 	      FIELD_PREP(IRDMAQPSQ_INLINEDATALEN, op_info->len) |
 	      FIELD_PREP(IRDMAQPSQ_REPORTRTT, info->report_rtt ? 1 : 0) |
@@ -745,9 +743,8 @@
  * @info: post sq information
  * @post_sq: flag to post sq
  */
-enum irdma_status_code irdma_uk_inline_send(struct irdma_qp_uk *qp,
-					    struct irdma_post_sq_info *info,
-					    bool post_sq)
+int irdma_uk_inline_send(struct irdma_qp_uk *qp,
+			 struct irdma_post_sq_info *info, bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_post_inline_send *op_info;
@@ -760,13 +757,13 @@
 	op_info = &info->op.inline_send;
 
 	if (op_info->len > qp->max_inline_data)
-		return IRDMA_ERR_INVALID_INLINE_DATA_SIZE;
+		return -EINVAL;
 
 	quanta = qp->wqe_ops.iw_inline_data_size_to_quanta(op_info->len);
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, quanta, op_info->len,
 					 info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
@@ -817,16 +814,16 @@
  * @info: post sq information
  * @post_sq: flag to post sq
  */
-enum irdma_status_code
-irdma_uk_stag_local_invalidate(struct irdma_qp_uk *qp,
-			       struct irdma_post_sq_info *info, bool post_sq)
+int irdma_uk_stag_local_invalidate(struct irdma_qp_uk *qp,
+				   struct irdma_post_sq_info *info,
+				   bool post_sq)
 {
 	__le64 *wqe;
 	struct irdma_inv_local_stag *op_info;
 	u64 hdr;
 	u32 wqe_idx;
 	bool local_fence = false;
-	struct irdma_sge sge = {};
+	struct ib_sge sge = {};
 
 	info->push_wqe = qp->push_db ? true : false;
 	op_info = &info->op.inv_local_stag;
@@ -835,11 +832,11 @@
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, IRDMA_QP_WQE_MIN_QUANTA,
 					 0, info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
-	sge.stag = op_info->target_stag;
+	sge.lkey = op_info->target_stag;
 	qp->wqe_ops.iw_set_fragment(wqe, 0, &sge, 0);
 
 	set_64bit_val(wqe, 16, 0);
@@ -867,69 +864,12 @@
 }
 
 /**
- * irdma_uk_mw_bind - bind Memory Window
- * @qp: hw qp ptr
- * @info: post sq information
- * @post_sq: flag to post sq
- */
-enum irdma_status_code irdma_uk_mw_bind(struct irdma_qp_uk *qp,
-					struct irdma_post_sq_info *info,
-					bool post_sq)
-{
-	__le64 *wqe;
-	struct irdma_bind_window *op_info;
-	u64 hdr;
-	u32 wqe_idx;
-	bool local_fence = false;
-
-	info->push_wqe = qp->push_db ? true : false;
-	op_info = &info->op.bind_window;
-	local_fence |= info->local_fence;
-
-	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, IRDMA_QP_WQE_MIN_QUANTA,
-					 0, info);
-	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
-
-	irdma_clr_wqes(qp, wqe_idx);
-
-	qp->wqe_ops.iw_set_mw_bind_wqe(wqe, op_info);
-
-	hdr = FIELD_PREP(IRDMAQPSQ_OPCODE, IRDMA_OP_TYPE_BIND_MW) |
-	      FIELD_PREP(IRDMAQPSQ_STAGRIGHTS,
-			 ((op_info->ena_reads << 2) | (op_info->ena_writes << 3))) |
-	      FIELD_PREP(IRDMAQPSQ_VABASEDTO,
-			 (op_info->addressing_type == IRDMA_ADDR_TYPE_VA_BASED ? 1 : 0)) |
-	      FIELD_PREP(IRDMAQPSQ_MEMWINDOWTYPE,
-			 (op_info->mem_window_type_1 ? 1 : 0)) |
-	      FIELD_PREP(IRDMAQPSQ_PUSHWQE, info->push_wqe) |
-	      FIELD_PREP(IRDMAQPSQ_READFENCE, info->read_fence) |
-	      FIELD_PREP(IRDMAQPSQ_LOCALFENCE, local_fence) |
-	      FIELD_PREP(IRDMAQPSQ_SIGCOMPL, info->signaled) |
-	      FIELD_PREP(IRDMAQPSQ_VALID, qp->swqe_polarity);
-
-	dma_wmb(); /* make sure WQE is populated before valid bit is set */
-
-	set_64bit_val(wqe, 24, hdr);
-
-	if (info->push_wqe) {
-		irdma_qp_push_wqe(qp, wqe, IRDMA_QP_WQE_MIN_QUANTA, wqe_idx,
-				  post_sq);
-	} else {
-		if (post_sq)
-			irdma_uk_qp_post_wr(qp);
-	}
-
-	return 0;
-}
-
-/**
  * irdma_uk_post_receive - post receive wqe
  * @qp: hw qp ptr
  * @info: post rq information
  */
-enum irdma_status_code irdma_uk_post_receive(struct irdma_qp_uk *qp,
-					     struct irdma_post_rq_info *info)
+int irdma_uk_post_receive(struct irdma_qp_uk *qp,
+			  struct irdma_post_rq_info *info)
 {
 	u32 wqe_idx, i, byte_off;
 	u32 addl_frag_cnt;
@@ -937,11 +877,11 @@
 	u64 hdr;
 
 	if (qp->max_rq_frag_cnt < info->num_sges)
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 
 	wqe = irdma_qp_get_next_recv_wqe(qp, &wqe_idx);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	qp->rq_wrid_array[wqe_idx] = info->wr_id;
 	addl_frag_cnt = info->num_sges > 1 ? (info->num_sges - 1) : 0;
@@ -1057,17 +997,18 @@
  * @cq: hw cq
  * @info: cq poll information returned
  */
-enum irdma_status_code
-irdma_uk_cq_poll_cmpl(struct irdma_cq_uk *cq, struct irdma_cq_poll_info *info)
+int irdma_uk_cq_poll_cmpl(struct irdma_cq_uk *cq,
+			  struct irdma_cq_poll_info *info)
 {
 	u64 comp_ctx, qword0, qword2, qword3;
 	__le64 *cqe;
 	struct irdma_qp_uk *qp;
 	struct irdma_ring *pring = NULL;
 	u32 wqe_idx, q_type;
-	enum irdma_status_code ret_code;
+	int ret_code;
 	bool move_cq_head = true;
 	u8 polarity;
+	u8 op_type;
 	bool ext_valid;
 	__le64 *ext_cqe;
 
@@ -1079,7 +1020,7 @@
 	get_64bit_val(cqe, 24, &qword3);
 	polarity = (u8)FIELD_GET(IRDMA_CQ_VALID, qword3);
 	if (polarity != cq->polarity)
-		return IRDMA_ERR_Q_EMPTY;
+		return -ENOENT;
 
 	/* Ensure CQE contents are read after valid bit is checked */
 	dma_rmb();
@@ -1102,7 +1043,7 @@
 				polarity ^= 1;
 		}
 		if (polarity != cq->polarity)
-			return IRDMA_ERR_Q_EMPTY;
+			return -ENOENT;
 
 		/* Ensure ext CQE contents are read after ext valid bit is checked */
 		dma_rmb();
@@ -1169,7 +1110,7 @@
 	info->solicited_event = (bool)FIELD_GET(IRDMACQ_SOEVENT, qword3);
 	qp = (struct irdma_qp_uk *)(unsigned long)comp_ctx;
 	if (!qp || qp->destroy_pending) {
-		ret_code = IRDMA_ERR_Q_DESTROYED;
+		ret_code = -EFAULT;
 		goto exit;
 	}
 	wqe_idx = (u32)FIELD_GET(IRDMA_CQ_WQEIDX, qword3);
@@ -1183,7 +1124,7 @@
 		if (info->comp_status == IRDMA_COMPL_STATUS_FLUSHED ||
 		    info->comp_status == IRDMA_COMPL_STATUS_UNKNOWN) {
 			if (!IRDMA_RING_MORE_WORK(qp->rq_ring)) {
-				ret_code = IRDMA_ERR_Q_EMPTY;
+				ret_code = -ENOENT;
 				goto exit;
 			}
 
@@ -1243,14 +1184,13 @@
 					    wqe_idx + qp->sq_wrtrk_array[wqe_idx].quanta);
 		} else {
 			if (!IRDMA_RING_MORE_WORK(qp->sq_ring)) {
-				ret_code = IRDMA_ERR_Q_EMPTY;
+				ret_code = -ENOENT;
 				goto exit;
 			}
 
 			do {
 				__le64 *sw_wqe;
 				u64 wqe_qword;
-				u8 op_type;
 				u32 tail;
 
 				tail = qp->sq_ring.tail;
@@ -1267,6 +1207,8 @@
 					break;
 				}
 			} while (1);
+			if (op_type == IRDMA_OP_TYPE_BIND_MW && info->minor_err == FLUSH_PROT_ERR)
+				info->minor_err = FLUSH_MW_BIND_ERR;
 			qp->sq_flush_seen = true;
 			if (!IRDMA_RING_MORE_WORK(qp->sq_ring))
 				qp->sq_flush_complete = true;
@@ -1360,15 +1302,15 @@
  * @sqdepth: depth of SQ
  *
  */
-enum irdma_status_code irdma_get_sqdepth(struct irdma_uk_attrs *uk_attrs,
-					 u32 sq_size, u8 shift, u32 *sqdepth)
+int irdma_get_sqdepth(struct irdma_uk_attrs *uk_attrs, u32 sq_size, u8 shift,
+		      u32 *sqdepth)
 {
 	*sqdepth = irdma_qp_round_up((sq_size << shift) + IRDMA_SQ_RSVD);
 
 	if (*sqdepth < (IRDMA_QP_SW_MIN_WQSIZE << shift))
 		*sqdepth = IRDMA_QP_SW_MIN_WQSIZE << shift;
 	else if (*sqdepth > uk_attrs->max_hw_wq_quanta)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	return 0;
 }
@@ -1380,15 +1322,15 @@
  * @shift: shift which determines size of WQE
  * @rqdepth: depth of RQ
  */
-enum irdma_status_code irdma_get_rqdepth(struct irdma_uk_attrs *uk_attrs,
-					 u32 rq_size, u8 shift, u32 *rqdepth)
+int irdma_get_rqdepth(struct irdma_uk_attrs *uk_attrs, u32 rq_size, u8 shift,
+		      u32 *rqdepth)
 {
 	*rqdepth = irdma_qp_round_up((rq_size << shift) + IRDMA_RQ_RSVD);
 
 	if (*rqdepth < (IRDMA_QP_SW_MIN_WQSIZE << shift))
 		*rqdepth = IRDMA_QP_SW_MIN_WQSIZE << shift;
 	else if (*rqdepth > uk_attrs->max_hw_rq_quanta)
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 
 	return 0;
 }
@@ -1438,17 +1380,16 @@
  * allowed. Then size of wqe * the number of wqes should be the
  * amount of memory allocated for sq and rq.
  */
-enum irdma_status_code irdma_uk_qp_init(struct irdma_qp_uk *qp,
-					struct irdma_qp_uk_init_info *info)
+int irdma_uk_qp_init(struct irdma_qp_uk *qp, struct irdma_qp_uk_init_info *info)
 {
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 	u32 sq_ring_size;
 	u8 sqshift, rqshift;
 
 	qp->uk_attrs = info->uk_attrs;
 	if (info->max_sq_frag_cnt > qp->uk_attrs->max_hw_wq_frags ||
 	    info->max_rq_frag_cnt > qp->uk_attrs->max_hw_wq_frags)
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 
 	irdma_get_wqe_shift(qp->uk_attrs, info->max_rq_frag_cnt, 0, &rqshift);
 	if (qp->uk_attrs->hw_rev == IRDMA_GEN_1) {
@@ -1503,8 +1444,8 @@
  * @cq: hw cq
  * @info: hw cq initialization info
  */
-enum irdma_status_code irdma_uk_cq_init(struct irdma_cq_uk *cq,
-					struct irdma_cq_uk_init_info *info)
+void irdma_uk_cq_init(struct irdma_cq_uk *cq,
+		      struct irdma_cq_uk_init_info *info)
 {
 	cq->cq_base = info->cq_base;
 	cq->cq_id = info->cq_id;
@@ -1515,8 +1456,6 @@
 	cq->avoid_mem_cflct = info->avoid_mem_cflct;
 	IRDMA_RING_INIT(cq->cq_ring, cq->cq_size);
 	cq->polarity = 1;
-
-	return 0;
 }
 
 /**
@@ -1544,6 +1483,9 @@
 		if (polarity != temp)
 			break;
 
+		/* Ensure CQE contents are read after valid bit is checked */
+		dma_rmb();
+
 		get_64bit_val(cqe, 8, &comp_ctx);
 		if ((void *)(unsigned long)comp_ctx == q)
 			set_64bit_val(cqe, 8, 0);
@@ -1561,8 +1503,7 @@
  * @signaled: signaled for completion
  * @post_sq: ring doorbell
  */
-enum irdma_status_code irdma_nop(struct irdma_qp_uk *qp, u64 wr_id,
-				 bool signaled, bool post_sq)
+int irdma_nop(struct irdma_qp_uk *qp, u64 wr_id, bool signaled, bool post_sq)
 {
 	__le64 *wqe;
 	u64 hdr;
@@ -1574,7 +1515,7 @@
 	wqe = irdma_qp_get_next_send_wqe(qp, &wqe_idx, IRDMA_QP_WQE_MIN_QUANTA,
 					 0, &info);
 	if (!wqe)
-		return IRDMA_ERR_QP_TOOMANY_WRS_POSTED;
+		return -ENOMEM;
 
 	irdma_clr_wqes(qp, wqe_idx);
 
@@ -1600,7 +1541,7 @@
  * @frag_cnt: number of fragments
  * @quanta: quanta for frag_cnt
  */
-enum irdma_status_code irdma_fragcnt_to_quanta_sq(u32 frag_cnt, u16 *quanta)
+int irdma_fragcnt_to_quanta_sq(u32 frag_cnt, u16 *quanta)
 {
 	switch (frag_cnt) {
 	case 0:
@@ -1636,7 +1577,7 @@
 		*quanta = 8;
 		break;
 	default:
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 	}
 
 	return 0;
@@ -1647,7 +1588,7 @@
  * @frag_cnt: number of fragments
  * @wqe_size: size in bytes given frag_cnt
  */
-enum irdma_status_code irdma_fragcnt_to_wqesize_rq(u32 frag_cnt, u16 *wqe_size)
+int irdma_fragcnt_to_wqesize_rq(u32 frag_cnt, u16 *wqe_size)
 {
 	switch (frag_cnt) {
 	case 0:
@@ -1674,7 +1615,7 @@
 		*wqe_size = 256;
 		break;
 	default:
-		return IRDMA_ERR_INVALID_FRAG_COUNT;
+		return -EINVAL;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/user.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/user.h
@@ -16,7 +16,6 @@
 #define irdma_access_privileges u32
 #define irdma_physical_fragment u64
 #define irdma_address_list u64 *
-#define irdma_sgl struct irdma_sge *
 
 #define	IRDMA_MAX_MR_SIZE       0x200000000000ULL
 
@@ -104,6 +103,7 @@
 	FLUSH_FATAL_ERR,
 	FLUSH_RETRY_EXC_ERR,
 	FLUSH_MW_BIND_ERR,
+	FLUSH_REM_INV_REQ_ERR,
 };
 
 enum irdma_cmpl_status {
@@ -151,12 +151,6 @@
 struct irdma_qp_uk_init_info;
 struct irdma_cq_uk_init_info;
 
-struct irdma_sge {
-	irdma_tagged_offset tag_off;
-	u32 len;
-	irdma_stag stag;
-};
-
 struct irdma_ring {
 	u32 head;
 	u32 tail;
@@ -172,7 +166,7 @@
 };
 
 struct irdma_post_send {
-	irdma_sgl sg_list;
+	struct ib_sge *sg_list;
 	u32 num_sges;
 	u32 qkey;
 	u32 dest_qp;
@@ -189,26 +183,26 @@
 
 struct irdma_post_rq_info {
 	u64 wr_id;
-	irdma_sgl sg_list;
+	struct ib_sge *sg_list;
 	u32 num_sges;
 };
 
 struct irdma_rdma_write {
-	irdma_sgl lo_sg_list;
+	struct ib_sge *lo_sg_list;
 	u32 num_lo_sges;
-	struct irdma_sge rem_addr;
+	struct ib_sge rem_addr;
 };
 
 struct irdma_inline_rdma_write {
 	void *data;
 	u32 len;
-	struct irdma_sge rem_addr;
+	struct ib_sge rem_addr;
 };
 
 struct irdma_rdma_read {
-	irdma_sgl lo_sg_list;
+	struct ib_sge *lo_sg_list;
 	u32 num_lo_sges;
-	struct irdma_sge rem_addr;
+	struct ib_sge rem_addr;
 };
 
 struct irdma_bind_window {
@@ -277,51 +271,44 @@
 	bool imm_valid:1;
 };
 
-enum irdma_status_code irdma_uk_inline_rdma_write(struct irdma_qp_uk *qp,
-						  struct irdma_post_sq_info *info,
-						  bool post_sq);
-enum irdma_status_code irdma_uk_inline_send(struct irdma_qp_uk *qp,
-					    struct irdma_post_sq_info *info,
-					    bool post_sq);
-enum irdma_status_code irdma_uk_mw_bind(struct irdma_qp_uk *qp,
-					struct irdma_post_sq_info *info,
-					bool post_sq);
-enum irdma_status_code irdma_uk_post_nop(struct irdma_qp_uk *qp, u64 wr_id,
-					 bool signaled, bool post_sq);
-enum irdma_status_code irdma_uk_post_receive(struct irdma_qp_uk *qp,
-					     struct irdma_post_rq_info *info);
+int irdma_uk_inline_rdma_write(struct irdma_qp_uk *qp,
+			       struct irdma_post_sq_info *info, bool post_sq);
+int irdma_uk_inline_send(struct irdma_qp_uk *qp,
+			 struct irdma_post_sq_info *info, bool post_sq);
+int irdma_uk_post_nop(struct irdma_qp_uk *qp, u64 wr_id, bool signaled,
+		      bool post_sq);
+int irdma_uk_post_receive(struct irdma_qp_uk *qp,
+			  struct irdma_post_rq_info *info);
 void irdma_uk_qp_post_wr(struct irdma_qp_uk *qp);
-enum irdma_status_code irdma_uk_rdma_read(struct irdma_qp_uk *qp,
-					  struct irdma_post_sq_info *info,
-					  bool inv_stag, bool post_sq);
-enum irdma_status_code irdma_uk_rdma_write(struct irdma_qp_uk *qp,
-					   struct irdma_post_sq_info *info,
-					   bool post_sq);
-enum irdma_status_code irdma_uk_send(struct irdma_qp_uk *qp,
-				     struct irdma_post_sq_info *info, bool post_sq);
-enum irdma_status_code irdma_uk_stag_local_invalidate(struct irdma_qp_uk *qp,
-						      struct irdma_post_sq_info *info,
-						      bool post_sq);
+int irdma_uk_rdma_read(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
+		       bool inv_stag, bool post_sq);
+int irdma_uk_rdma_write(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
+			bool post_sq);
+int irdma_uk_send(struct irdma_qp_uk *qp, struct irdma_post_sq_info *info,
+		  bool post_sq);
+int irdma_uk_stag_local_invalidate(struct irdma_qp_uk *qp,
+				   struct irdma_post_sq_info *info,
+				   bool post_sq);
 
 struct irdma_wqe_uk_ops {
 	void (*iw_copy_inline_data)(u8 *dest, u8 *src, u32 len, u8 polarity);
 	u16 (*iw_inline_data_size_to_quanta)(u32 data_size);
-	void (*iw_set_fragment)(__le64 *wqe, u32 offset, struct irdma_sge *sge,
+	void (*iw_set_fragment)(__le64 *wqe, u32 offset, struct ib_sge *sge,
 				u8 valid);
 	void (*iw_set_mw_bind_wqe)(__le64 *wqe,
 				   struct irdma_bind_window *op_info);
 };
 
-enum irdma_status_code irdma_uk_cq_poll_cmpl(struct irdma_cq_uk *cq,
-					     struct irdma_cq_poll_info *info);
+int irdma_uk_cq_poll_cmpl(struct irdma_cq_uk *cq,
+			  struct irdma_cq_poll_info *info);
 void irdma_uk_cq_request_notification(struct irdma_cq_uk *cq,
 				      enum irdma_cmpl_notify cq_notify);
 void irdma_uk_cq_resize(struct irdma_cq_uk *cq, void *cq_base, int size);
 void irdma_uk_cq_set_resized_cnt(struct irdma_cq_uk *qp, u16 cnt);
-enum irdma_status_code irdma_uk_cq_init(struct irdma_cq_uk *cq,
-					struct irdma_cq_uk_init_info *info);
-enum irdma_status_code irdma_uk_qp_init(struct irdma_qp_uk *qp,
-					struct irdma_qp_uk_init_info *info);
+void irdma_uk_cq_init(struct irdma_cq_uk *cq,
+		      struct irdma_cq_uk_init_info *info);
+int irdma_uk_qp_init(struct irdma_qp_uk *qp,
+		     struct irdma_qp_uk_init_info *info);
 struct irdma_sq_uk_wr_trk_info {
 	u64 wrid;
 	u32 wr_len;
@@ -423,16 +410,15 @@
 				   struct irdma_post_sq_info *info);
 __le64 *irdma_qp_get_next_recv_wqe(struct irdma_qp_uk *qp, u32 *wqe_idx);
 void irdma_uk_clean_cq(void *q, struct irdma_cq_uk *cq);
-enum irdma_status_code irdma_nop(struct irdma_qp_uk *qp, u64 wr_id,
-				 bool signaled, bool post_sq);
-enum irdma_status_code irdma_fragcnt_to_quanta_sq(u32 frag_cnt, u16 *quanta);
-enum irdma_status_code irdma_fragcnt_to_wqesize_rq(u32 frag_cnt, u16 *wqe_size);
+int irdma_nop(struct irdma_qp_uk *qp, u64 wr_id, bool signaled, bool post_sq);
+int irdma_fragcnt_to_quanta_sq(u32 frag_cnt, u16 *quanta);
+int irdma_fragcnt_to_wqesize_rq(u32 frag_cnt, u16 *wqe_size);
 void irdma_get_wqe_shift(struct irdma_uk_attrs *uk_attrs, u32 sge,
 			 u32 inline_data, u8 *shift);
-enum irdma_status_code irdma_get_sqdepth(struct irdma_uk_attrs *uk_attrs,
-					 u32 sq_size, u8 shift, u32 *wqdepth);
-enum irdma_status_code irdma_get_rqdepth(struct irdma_uk_attrs *uk_attrs,
-					 u32 rq_size, u8 shift, u32 *wqdepth);
+int irdma_get_sqdepth(struct irdma_uk_attrs *uk_attrs, u32 sq_size, u8 shift,
+		      u32 *wqdepth);
+int irdma_get_rqdepth(struct irdma_uk_attrs *uk_attrs, u32 rq_size, u8 shift,
+		      u32 *wqdepth);
 void irdma_qp_push_wqe(struct irdma_qp_uk *qp, __le64 *wqe, u16 quanta,
 		       u32 wqe_idx, bool post_sq);
 void irdma_clr_wqes(struct irdma_qp_uk *qp, u32 qp_wqe_idx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/utils.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/utils.c
@@ -150,31 +150,35 @@
 			 void *ptr)
 {
 	struct in_ifaddr *ifa = ptr;
-	struct net_device *netdev = ifa->ifa_dev->dev;
+	struct net_device *real_dev, *netdev = ifa->ifa_dev->dev;
 	struct irdma_device *iwdev;
 	struct ib_device *ibdev;
 	u32 local_ipaddr;
 
-	ibdev = ib_device_get_by_netdev(netdev, RDMA_DRIVER_IRDMA);
+	real_dev = rdma_vlan_dev_real_dev(netdev);
+	if (!real_dev)
+		real_dev = netdev;
+
+	ibdev = ib_device_get_by_netdev(real_dev, RDMA_DRIVER_IRDMA);
 	if (!ibdev)
 		return NOTIFY_DONE;
 
 	iwdev = to_iwdev(ibdev);
 	local_ipaddr = ntohl(ifa->ifa_address);
 	ibdev_dbg(&iwdev->ibdev,
-		  "DEV: netdev %p event %lu local_ip=%pI4 MAC=%pM\n", netdev,
-		  event, &local_ipaddr, netdev->dev_addr);
+		  "DEV: netdev %p event %lu local_ip=%pI4 MAC=%pM\n", real_dev,
+		  event, &local_ipaddr, real_dev->dev_addr);
 	switch (event) {
 	case NETDEV_DOWN:
-		irdma_manage_arp_cache(iwdev->rf, netdev->dev_addr,
+		irdma_manage_arp_cache(iwdev->rf, real_dev->dev_addr,
 				       &local_ipaddr, true, IRDMA_ARP_DELETE);
-		irdma_if_notify(iwdev, netdev, &local_ipaddr, true, false);
+		irdma_if_notify(iwdev, real_dev, &local_ipaddr, true, false);
 		irdma_gid_change_event(&iwdev->ibdev);
 		break;
 	case NETDEV_UP:
 	case NETDEV_CHANGEADDR:
-		irdma_add_arp(iwdev->rf, &local_ipaddr, true, netdev->dev_addr);
-		irdma_if_notify(iwdev, netdev, &local_ipaddr, true, true);
+		irdma_add_arp(iwdev->rf, &local_ipaddr, true, real_dev->dev_addr);
+		irdma_if_notify(iwdev, real_dev, &local_ipaddr, true, true);
 		irdma_gid_change_event(&iwdev->ibdev);
 		break;
 	default:
@@ -196,32 +200,36 @@
 			  void *ptr)
 {
 	struct inet6_ifaddr *ifa = ptr;
-	struct net_device *netdev = ifa->idev->dev;
+	struct net_device *real_dev, *netdev = ifa->idev->dev;
 	struct irdma_device *iwdev;
 	struct ib_device *ibdev;
 	u32 local_ipaddr6[4];
 
-	ibdev = ib_device_get_by_netdev(netdev, RDMA_DRIVER_IRDMA);
+	real_dev = rdma_vlan_dev_real_dev(netdev);
+	if (!real_dev)
+		real_dev = netdev;
+
+	ibdev = ib_device_get_by_netdev(real_dev, RDMA_DRIVER_IRDMA);
 	if (!ibdev)
 		return NOTIFY_DONE;
 
 	iwdev = to_iwdev(ibdev);
 	irdma_copy_ip_ntohl(local_ipaddr6, ifa->addr.in6_u.u6_addr32);
 	ibdev_dbg(&iwdev->ibdev,
-		  "DEV: netdev %p event %lu local_ip=%pI6 MAC=%pM\n", netdev,
-		  event, local_ipaddr6, netdev->dev_addr);
+		  "DEV: netdev %p event %lu local_ip=%pI6 MAC=%pM\n", real_dev,
+		  event, local_ipaddr6, real_dev->dev_addr);
 	switch (event) {
 	case NETDEV_DOWN:
-		irdma_manage_arp_cache(iwdev->rf, netdev->dev_addr,
+		irdma_manage_arp_cache(iwdev->rf, real_dev->dev_addr,
 				       local_ipaddr6, false, IRDMA_ARP_DELETE);
-		irdma_if_notify(iwdev, netdev, local_ipaddr6, false, false);
+		irdma_if_notify(iwdev, real_dev, local_ipaddr6, false, false);
 		irdma_gid_change_event(&iwdev->ibdev);
 		break;
 	case NETDEV_UP:
 	case NETDEV_CHANGEADDR:
 		irdma_add_arp(iwdev->rf, local_ipaddr6, false,
-			      netdev->dev_addr);
-		irdma_if_notify(iwdev, netdev, local_ipaddr6, false, true);
+			      real_dev->dev_addr);
+		irdma_if_notify(iwdev, real_dev, local_ipaddr6, false, true);
 		irdma_gid_change_event(&iwdev->ibdev);
 		break;
 	default:
@@ -243,21 +251,23 @@
 		    void *ptr)
 {
 	struct neighbour *neigh = ptr;
+	struct net_device *real_dev, *netdev = (struct net_device *)neigh->dev;
 	struct irdma_device *iwdev;
 	struct ib_device *ibdev;
 	__be32 *p;
 	u32 local_ipaddr[4] = {};
 	bool ipv4 = true;
 
-	ibdev = ib_device_get_by_netdev((struct net_device *)neigh->dev,
-					RDMA_DRIVER_IRDMA);
-	if (!ibdev)
-		return NOTIFY_DONE;
-
-	iwdev = to_iwdev(ibdev);
-
 	switch (event) {
 	case NETEVENT_NEIGH_UPDATE:
+		real_dev = rdma_vlan_dev_real_dev(netdev);
+		if (!real_dev)
+			real_dev = netdev;
+		ibdev = ib_device_get_by_netdev(real_dev, RDMA_DRIVER_IRDMA);
+		if (!ibdev)
+			return NOTIFY_DONE;
+
+		iwdev = to_iwdev(ibdev);
 		p = (__be32 *)neigh->primary_key;
 		if (neigh->tbl->family == AF_INET6) {
 			ipv4 = false;
@@ -278,13 +288,12 @@
 			irdma_manage_arp_cache(iwdev->rf, neigh->ha,
 					       local_ipaddr, ipv4,
 					       IRDMA_ARP_DELETE);
+		ib_device_put(ibdev);
 		break;
 	default:
 		break;
 	}
 
-	ib_device_put(ibdev);
-
 	return NOTIFY_DONE;
 }
 
@@ -472,7 +481,7 @@
 	if (cqp_request->dynamic) {
 		kfree(cqp_request);
 	} else {
-		cqp_request->request_done = false;
+		WRITE_ONCE(cqp_request->request_done, false);
 		cqp_request->callback_fcn = NULL;
 		cqp_request->waiting = false;
 
@@ -506,7 +515,7 @@
 {
 	if (cqp_request->waiting) {
 		cqp_request->compl_info.error = true;
-		cqp_request->request_done = true;
+		WRITE_ONCE(cqp_request->request_done, true);
 		wake_up(&cqp_request->waitq);
 	}
 	wait_event_timeout(cqp->remove_wq,
@@ -551,18 +560,18 @@
  * @rf: RDMA PCI function
  * @cqp_request: cqp request to wait
  */
-static enum irdma_status_code irdma_wait_event(struct irdma_pci_f *rf,
-					       struct irdma_cqp_request *cqp_request)
+static int irdma_wait_event(struct irdma_pci_f *rf,
+			    struct irdma_cqp_request *cqp_request)
 {
 	struct irdma_cqp_timeout cqp_timeout = {};
 	bool cqp_error = false;
-	enum irdma_status_code err_code = 0;
+	int err_code = 0;
 
-	cqp_timeout.compl_cqp_cmds = rf->sc_dev.cqp_cmd_stats[IRDMA_OP_CMPL_CMDS];
+	cqp_timeout.compl_cqp_cmds = atomic64_read(&rf->sc_dev.cqp->completed_ops);
 	do {
 		irdma_cqp_ce_handler(rf, &rf->ccq.sc_cq);
 		if (wait_event_timeout(cqp_request->waitq,
-				       cqp_request->request_done,
+				       READ_ONCE(cqp_request->request_done),
 				       msecs_to_jiffies(CQP_COMPL_WAIT_TIME_MS)))
 			break;
 
@@ -575,12 +584,12 @@
 			rf->reset = true;
 			rf->gen_ops.request_reset(rf);
 		}
-		return IRDMA_ERR_TIMEOUT;
+		return -ETIMEDOUT;
 	} while (1);
 
 	cqp_error = cqp_request->compl_info.error;
 	if (cqp_error) {
-		err_code = IRDMA_ERR_CQP_COMPL_ERROR;
+		err_code = -EIO;
 		if (cqp_request->compl_info.maj_err_code == 0xFFFF &&
 		    cqp_request->compl_info.min_err_code == 0x8029) {
 			if (!rf->reset) {
@@ -680,16 +689,16 @@
  * @rf: RDMA PCI function
  * @cqp_request: cqp request to process
  */
-enum irdma_status_code irdma_handle_cqp_op(struct irdma_pci_f *rf,
-					   struct irdma_cqp_request *cqp_request)
+int irdma_handle_cqp_op(struct irdma_pci_f *rf,
+			struct irdma_cqp_request *cqp_request)
 {
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct cqp_cmds_info *info = &cqp_request->info;
-	enum irdma_status_code status;
+	int status;
 	bool put_cqp_request = true;
 
 	if (rf->reset)
-		return IRDMA_ERR_NOT_READY;
+		return -EBUSY;
 
 	irdma_get_cqp_request(cqp_request);
 	status = irdma_process_cqp_cmd(dev, info);
@@ -768,17 +777,6 @@
 }
 
 /**
- * irdma_get_hw_addr - return hw addr
- * @par: points to shared dev
- */
-u8 __iomem *irdma_get_hw_addr(void *par)
-{
-	struct irdma_sc_dev *dev = par;
-
-	return dev->hw->hw_addr;
-}
-
-/**
  * irdma_remove_cqp_head - return head entry and remove
  * @dev: device
  */
@@ -802,17 +800,17 @@
  * @sdinfo: information for sd cqp
  *
  */
-enum irdma_status_code irdma_cqp_sds_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_update_sds_info *sdinfo)
+int irdma_cqp_sds_cmd(struct irdma_sc_dev *dev,
+		      struct irdma_update_sds_info *sdinfo)
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	memcpy(&cqp_info->in.u.update_pe_sds.info, sdinfo,
@@ -833,19 +831,18 @@
  * @qp: hardware control qp
  * @op: suspend or resume
  */
-enum irdma_status_code irdma_cqp_qp_suspend_resume(struct irdma_sc_qp *qp,
-						   u8 op)
+int irdma_cqp_qp_suspend_resume(struct irdma_sc_qp *qp, u8 op)
 {
 	struct irdma_sc_dev *dev = qp->dev;
 	struct irdma_cqp_request *cqp_request;
 	struct irdma_sc_cqp *cqp = dev->cqp;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, false);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_info->cqp_cmd = op;
@@ -951,18 +948,17 @@
  * @val_mem: buffer for fpm
  * @hmc_fn_id: function id for fpm
  */
-enum irdma_status_code
-irdma_cqp_query_fpm_val_cmd(struct irdma_sc_dev *dev,
-			    struct irdma_dma_mem *val_mem, u8 hmc_fn_id)
+int irdma_cqp_query_fpm_val_cmd(struct irdma_sc_dev *dev,
+				struct irdma_dma_mem *val_mem, u8 hmc_fn_id)
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_request->param = NULL;
@@ -986,18 +982,17 @@
  * @val_mem: buffer with fpm values
  * @hmc_fn_id: function id for fpm
  */
-enum irdma_status_code
-irdma_cqp_commit_fpm_val_cmd(struct irdma_sc_dev *dev,
-			     struct irdma_dma_mem *val_mem, u8 hmc_fn_id)
+int irdma_cqp_commit_fpm_val_cmd(struct irdma_sc_dev *dev,
+				 struct irdma_dma_mem *val_mem, u8 hmc_fn_id)
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_request->param = NULL;
@@ -1020,18 +1015,17 @@
  * @dev: device pointer
  * @cq: pointer to created cq
  */
-enum irdma_status_code irdma_cqp_cq_create_cmd(struct irdma_sc_dev *dev,
-					       struct irdma_sc_cq *cq)
+int irdma_cqp_cq_create_cmd(struct irdma_sc_dev *dev, struct irdma_sc_cq *cq)
 {
 	struct irdma_pci_f *rf = dev_to_rf(dev);
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_info->cqp_cmd = IRDMA_OP_CQ_CREATE;
@@ -1050,19 +1044,18 @@
  * @dev: device pointer
  * @qp: pointer to created qp
  */
-enum irdma_status_code irdma_cqp_qp_create_cmd(struct irdma_sc_dev *dev,
-					       struct irdma_sc_qp *qp)
+int irdma_cqp_qp_create_cmd(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp)
 {
 	struct irdma_pci_f *rf = dev_to_rf(dev);
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_create_qp_info *qp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	qp_info = &cqp_request->info.in.u.qp_create.info;
@@ -1090,7 +1083,7 @@
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	if (qp->push_idx == IRDMA_INVALID_PUSH_PAGE_INDEX)
 		return;
@@ -1190,12 +1183,10 @@
  * @info: info for modify qp
  * @wait: flag to wait or not for modify qp completion
  */
-enum irdma_status_code irdma_hw_modify_qp(struct irdma_device *iwdev,
-					  struct irdma_qp *iwqp,
-					  struct irdma_modify_qp_info *info,
-					  bool wait)
+int irdma_hw_modify_qp(struct irdma_device *iwdev, struct irdma_qp *iwqp,
+		       struct irdma_modify_qp_info *info, bool wait)
 {
-	enum irdma_status_code status;
+	int status;
 	struct irdma_pci_f *rf = iwdev->rf;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
@@ -1203,7 +1194,7 @@
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, wait);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	if (!wait) {
 		cqp_request->callback_fcn = irdma_hw_modify_qp_callback;
@@ -1241,7 +1232,7 @@
 				cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp,
 									      wait);
 				if (!cqp_request)
-					return IRDMA_ERR_NO_MEMORY;
+					return -ENOMEM;
 
 				cqp_info = &cqp_request->info;
 				m_info = &cqp_info->in.u.qp_modify.info;
@@ -1282,17 +1273,17 @@
  * @dev: device pointer
  * @qp: pointer to qp
  */
-enum irdma_status_code irdma_cqp_qp_destroy_cmd(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp)
+int irdma_cqp_qp_destroy_cmd(struct irdma_sc_dev *dev, struct irdma_sc_qp *qp)
 {
 	struct irdma_pci_f *rf = dev_to_rf(dev);
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	memset(cqp_info, 0, sizeof(*cqp_info));
@@ -1328,20 +1319,20 @@
  * irdma_init_hash_desc - initialize hash for crc calculation
  * @desc: cryption type
  */
-enum irdma_status_code irdma_init_hash_desc(struct shash_desc **desc)
+int irdma_init_hash_desc(struct shash_desc **desc)
 {
 	struct crypto_shash *tfm;
 	struct shash_desc *tdesc;
 
 	tfm = crypto_alloc_shash("crc32c", 0, 0);
 	if (IS_ERR(tfm))
-		return IRDMA_ERR_MPA_CRC;
+		return -EINVAL;
 
 	tdesc = kzalloc(sizeof(*tdesc) + crypto_shash_descsize(tfm),
 			GFP_KERNEL);
 	if (!tdesc) {
 		crypto_free_shash(tfm);
-		return IRDMA_ERR_MPA_CRC;
+		return -EINVAL;
 	}
 
 	tdesc->tfm = tfm;
@@ -1369,19 +1360,19 @@
  * @len: length of buffer
  * @val: value to be compared
  */
-enum irdma_status_code irdma_ieq_check_mpacrc(struct shash_desc *desc,
-					      void *addr, u32 len, u32 val)
+int irdma_ieq_check_mpacrc(struct shash_desc *desc, void *addr, u32 len,
+			   u32 val)
 {
 	u32 crc = 0;
 	int ret;
-	enum irdma_status_code ret_code = 0;
+	int ret_code = 0;
 
 	crypto_shash_init(desc);
 	ret = crypto_shash_update(desc, addr, len);
 	if (!ret)
 		crypto_shash_final(desc, (u8 *)&crc);
 	if (crc != val)
-		ret_code = IRDMA_ERR_MPA_CRC;
+		ret_code = -EINVAL;
 
 	return ret_code;
 }
@@ -1535,9 +1526,8 @@
  * @info: to get information
  * @buf: puda buffer
  */
-static enum irdma_status_code
-irdma_gen1_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
-			       struct irdma_puda_buf *buf)
+static int irdma_gen1_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
+					  struct irdma_puda_buf *buf)
 {
 	struct iphdr *iph;
 	struct ipv6hdr *ip6h;
@@ -1574,7 +1564,7 @@
 		ibdev_dbg(to_ibdev(buf->vsi->dev),
 			  "ERR: payload_len = 0x%x totallen expected0x%x\n",
 			  info->payload_len, buf->totallen);
-		return IRDMA_ERR_INVALID_SIZE;
+		return -EINVAL;
 	}
 
 	buf->tcphlen = tcph->doff << 2;
@@ -1591,9 +1581,8 @@
  * @info: to get information
  * @buf: puda buffer
  */
-enum irdma_status_code
-irdma_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
-			  struct irdma_puda_buf *buf)
+int irdma_puda_get_tcpip_info(struct irdma_puda_cmpl_info *info,
+			      struct irdma_puda_buf *buf)
 {
 	struct tcphdr *tcph;
 	u32 pkt_len;
@@ -1872,20 +1861,19 @@
  * @pestat: pointer to stats info
  * @wait: flag to wait or not wait for stats
  */
-enum irdma_status_code
-irdma_cqp_gather_stats_cmd(struct irdma_sc_dev *dev,
-			   struct irdma_vsi_pestat *pestat, bool wait)
+int irdma_cqp_gather_stats_cmd(struct irdma_sc_dev *dev,
+			       struct irdma_vsi_pestat *pestat, bool wait)
 
 {
 	struct irdma_pci_f *rf = dev_to_rf(dev);
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, wait);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	memset(cqp_info, 0, sizeof(*cqp_info));
@@ -1911,22 +1899,21 @@
  * @cmd: command to allocate or free
  * @stats_info: pointer to allocate stats info
  */
-enum irdma_status_code
-irdma_cqp_stats_inst_cmd(struct irdma_sc_vsi *vsi, u8 cmd,
-			 struct irdma_stats_inst_info *stats_info)
+int irdma_cqp_stats_inst_cmd(struct irdma_sc_vsi *vsi, u8 cmd,
+			     struct irdma_stats_inst_info *stats_info)
 {
 	struct irdma_pci_f *rf = dev_to_rf(vsi->dev);
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 	bool wait = false;
 
 	if (cmd == IRDMA_OP_STATS_ALLOCATE)
 		wait = true;
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, wait);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	memset(cqp_info, 0, sizeof(*cqp_info));
@@ -1949,17 +1936,17 @@
  * @sc_ceq: pointer to ceq structure
  * @op: Create or Destroy
  */
-enum irdma_status_code irdma_cqp_ceq_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_sc_ceq *sc_ceq, u8 op)
+int irdma_cqp_ceq_cmd(struct irdma_sc_dev *dev, struct irdma_sc_ceq *sc_ceq,
+		      u8 op)
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_info->post_sq = 1;
@@ -1979,17 +1966,17 @@
  * @sc_aeq: pointer to aeq structure
  * @op: Create or Destroy
  */
-enum irdma_status_code irdma_cqp_aeq_cmd(struct irdma_sc_dev *dev,
-					 struct irdma_sc_aeq *sc_aeq, u8 op)
+int irdma_cqp_aeq_cmd(struct irdma_sc_dev *dev, struct irdma_sc_aeq *sc_aeq,
+		      u8 op)
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	cqp_info->post_sq = 1;
@@ -2009,16 +1996,15 @@
  * @cmd: Add, modify or delete
  * @node_info: pointer to ws node info
  */
-enum irdma_status_code
-irdma_cqp_ws_node_cmd(struct irdma_sc_dev *dev, u8 cmd,
-		      struct irdma_ws_node_info *node_info)
+int irdma_cqp_ws_node_cmd(struct irdma_sc_dev *dev, u8 cmd,
+			  struct irdma_ws_node_info *node_info)
 {
 	struct irdma_pci_f *rf = dev_to_rf(dev);
 	struct irdma_cqp *iwcqp = &rf->cqp;
 	struct irdma_sc_cqp *cqp = &iwcqp->sc_cqp;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 	bool poll;
 
 	if (!rf->sc_dev.ceq_valid)
@@ -2028,7 +2014,7 @@
 
 	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, !poll);
 	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	cqp_info = &cqp_request->info;
 	memset(cqp_info, 0, sizeof(*cqp_info));
@@ -2060,40 +2046,6 @@
 }
 
 /**
- * irdma_cqp_up_map_cmd - Set the up-up mapping
- * @dev: pointer to device structure
- * @cmd: map command
- * @map_info: pointer to up map info
- */
-enum irdma_status_code irdma_cqp_up_map_cmd(struct irdma_sc_dev *dev, u8 cmd,
-					    struct irdma_up_info *map_info)
-{
-	struct irdma_pci_f *rf = dev_to_rf(dev);
-	struct irdma_cqp *iwcqp = &rf->cqp;
-	struct irdma_sc_cqp *cqp = &iwcqp->sc_cqp;
-	struct irdma_cqp_request *cqp_request;
-	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
-
-	cqp_request = irdma_alloc_and_get_cqp_request(iwcqp, false);
-	if (!cqp_request)
-		return IRDMA_ERR_NO_MEMORY;
-
-	cqp_info = &cqp_request->info;
-	memset(cqp_info, 0, sizeof(*cqp_info));
-	cqp_info->cqp_cmd = cmd;
-	cqp_info->post_sq = 1;
-	cqp_info->in.u.up_map.info = *map_info;
-	cqp_info->in.u.up_map.cqp = cqp;
-	cqp_info->in.u.up_map.scratch = (uintptr_t)cqp_request;
-
-	status = irdma_handle_cqp_op(rf, cqp_request);
-	irdma_put_cqp_request(&rf->cqp, cqp_request);
-
-	return status;
-}
-
-/**
  * irdma_ah_cqp_op - perform an AH cqp operation
  * @rf: RDMA PCI function
  * @sc_ah: address handle
@@ -2111,7 +2063,7 @@
 {
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	if (cmd != IRDMA_OP_AH_CREATE && cmd != IRDMA_OP_AH_DESTROY)
 		return -EINVAL;
@@ -2193,11 +2145,10 @@
  * @ah_ret: Returned pointer to address handle if created
  *
  */
-enum irdma_status_code irdma_puda_create_ah(struct irdma_sc_dev *dev,
-					    struct irdma_ah_info *ah_info,
-					    bool wait, enum puda_rsrc_type type,
-					    void *cb_param,
-					    struct irdma_sc_ah **ah_ret)
+int irdma_puda_create_ah(struct irdma_sc_dev *dev,
+			 struct irdma_ah_info *ah_info, bool wait,
+			 enum puda_rsrc_type type, void *cb_param,
+			 struct irdma_sc_ah **ah_ret)
 {
 	struct irdma_sc_ah *ah;
 	struct irdma_pci_f *rf = dev_to_rf(dev);
@@ -2206,7 +2157,7 @@
 	ah = kzalloc(sizeof(*ah), GFP_ATOMIC);
 	*ah_ret = ah;
 	if (!ah)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	err = irdma_alloc_rsrc(rf, rf->allocated_ahs, rf->max_ah,
 			       &ah_info->ah_idx, &rf->next_ah);
@@ -2232,7 +2183,7 @@
 err_free:
 	kfree(ah);
 	*ah_ret = NULL;
-	return IRDMA_ERR_NO_MEMORY;
+	return -ENOMEM;
 }
 
 /**
@@ -2274,24 +2225,19 @@
  * @pprm: pble resource manager
  * @pchunk: chunk of memory to add
  */
-enum irdma_status_code irdma_prm_add_pble_mem(struct irdma_pble_prm *pprm,
-					      struct irdma_chunk *pchunk)
+int irdma_prm_add_pble_mem(struct irdma_pble_prm *pprm,
+			   struct irdma_chunk *pchunk)
 {
 	u64 sizeofbitmap;
 
 	if (pchunk->size & 0xfff)
-		return IRDMA_ERR_PARAM;
+		return -EINVAL;
 
 	sizeofbitmap = (u64)pchunk->size >> pprm->pble_shift;
 
-	pchunk->bitmapmem.size = sizeofbitmap >> 3;
-	pchunk->bitmapmem.va = kzalloc(pchunk->bitmapmem.size, GFP_KERNEL);
-
-	if (!pchunk->bitmapmem.va)
-		return IRDMA_ERR_NO_MEMORY;
-
-	pchunk->bitmapbuf = pchunk->bitmapmem.va;
-	bitmap_zero(pchunk->bitmapbuf, sizeofbitmap);
+	pchunk->bitmapbuf = bitmap_zalloc(sizeofbitmap, GFP_KERNEL);
+	if (!pchunk->bitmapbuf)
+		return -ENOMEM;
 
 	pchunk->sizeofbitmap = sizeofbitmap;
 	/* each pble is 8 bytes hence shift by 3 */
@@ -2309,10 +2255,9 @@
  * @vaddr: returns virtual address of pble memory
  * @fpm_addr: returns fpm address of pble memory
  */
-enum irdma_status_code
-irdma_prm_get_pbles(struct irdma_pble_prm *pprm,
-		    struct irdma_pble_chunkinfo *chunkinfo, u64 mem_size,
-		    u64 **vaddr, u64 *fpm_addr)
+int irdma_prm_get_pbles(struct irdma_pble_prm *pprm,
+			struct irdma_pble_chunkinfo *chunkinfo, u64 mem_size,
+			u64 **vaddr, u64 *fpm_addr)
 {
 	u64 bits_needed;
 	u64 bit_idx = PBLE_INVALID_IDX;
@@ -2340,7 +2285,7 @@
 
 	if (!pchunk || bit_idx >= pchunk->sizeofbitmap) {
 		spin_unlock_irqrestore(&pprm->prm_lock, flags);
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 
 	bitmap_set(pchunk->bitmapbuf, bit_idx, bits_needed);
@@ -2375,8 +2320,8 @@
 	spin_unlock_irqrestore(&pprm->prm_lock, flags);
 }
 
-enum irdma_status_code irdma_map_vm_page_list(struct irdma_hw *hw, void *va,
-					      dma_addr_t *pg_dma, u32 pg_cnt)
+int irdma_map_vm_page_list(struct irdma_hw *hw, void *va, dma_addr_t *pg_dma,
+			   u32 pg_cnt)
 {
 	struct page *vm_page;
 	int i;
@@ -2400,7 +2345,7 @@
 
 err:
 	irdma_unmap_vm_page_list(hw, pg_dma, i);
-	return IRDMA_ERR_NO_MEMORY;
+	return -ENOMEM;
 }
 
 void irdma_unmap_vm_page_list(struct irdma_hw *hw, dma_addr_t *pg_dma, u32 pg_cnt)
@@ -2436,15 +2381,14 @@
  * @chunk: chunk to add for paged memory
  * @pg_cnt: number of pages needed
  */
-enum irdma_status_code irdma_pble_get_paged_mem(struct irdma_chunk *chunk,
-						u32 pg_cnt)
+int irdma_pble_get_paged_mem(struct irdma_chunk *chunk, u32 pg_cnt)
 {
 	u32 size;
 	void *va;
 
 	chunk->dmainfo.dmaaddrs = kzalloc(pg_cnt << 3, GFP_KERNEL);
 	if (!chunk->dmainfo.dmaaddrs)
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 
 	size = PAGE_SIZE * pg_cnt;
 	va = vmalloc(size);
@@ -2466,7 +2410,7 @@
 	kfree(chunk->dmainfo.dmaaddrs);
 	chunk->dmainfo.dmaaddrs = NULL;
 
-	return IRDMA_ERR_NO_MEMORY;
+	return -ENOMEM;
 }
 
 /**
@@ -2531,8 +2475,176 @@
 	case IRDMA_QP_EVENT_ACCESS_ERR:
 		ibevent.event = IB_EVENT_QP_ACCESS_ERR;
 		break;
+	case IRDMA_QP_EVENT_REQ_ERR:
+		ibevent.event = IB_EVENT_QP_REQ_ERR;
+		break;
 	}
 	ibevent.device = iwqp->ibqp.device;
 	ibevent.element.qp = &iwqp->ibqp;
 	iwqp->ibqp.event_handler(&ibevent, iwqp->ibqp.qp_context);
 }
+
+bool irdma_cq_empty(struct irdma_cq *iwcq)
+{
+	struct irdma_cq_uk *ukcq;
+	u64 qword3;
+	__le64 *cqe;
+	u8 polarity;
+
+	ukcq  = &iwcq->sc_cq.cq_uk;
+	cqe = IRDMA_GET_CURRENT_CQ_ELEM(ukcq);
+	get_64bit_val(cqe, 24, &qword3);
+	polarity = (u8)FIELD_GET(IRDMA_CQ_VALID, qword3);
+
+	return polarity != ukcq->polarity;
+}
+
+void irdma_remove_cmpls_list(struct irdma_cq *iwcq)
+{
+	struct irdma_cmpl_gen *cmpl_node;
+	struct list_head *tmp_node, *list_node;
+
+	list_for_each_safe (list_node, tmp_node, &iwcq->cmpl_generated) {
+		cmpl_node = list_entry(list_node, struct irdma_cmpl_gen, list);
+		list_del(&cmpl_node->list);
+		kfree(cmpl_node);
+	}
+}
+
+int irdma_generated_cmpls(struct irdma_cq *iwcq, struct irdma_cq_poll_info *cq_poll_info)
+{
+	struct irdma_cmpl_gen *cmpl;
+
+	if (list_empty(&iwcq->cmpl_generated))
+		return -ENOENT;
+	cmpl = list_first_entry_or_null(&iwcq->cmpl_generated, struct irdma_cmpl_gen, list);
+	list_del(&cmpl->list);
+	memcpy(cq_poll_info, &cmpl->cpi, sizeof(*cq_poll_info));
+	kfree(cmpl);
+
+	ibdev_dbg(iwcq->ibcq.device,
+		  "VERBS: %s: Poll artificially generated completion for QP 0x%X, op %u, wr_id=0x%llx\n",
+		  __func__, cq_poll_info->qp_id, cq_poll_info->op_type,
+		  cq_poll_info->wr_id);
+
+	return 0;
+}
+
+/**
+ * irdma_set_cpi_common_values - fill in values for polling info struct
+ * @cpi: resulting structure of cq_poll_info type
+ * @qp: QPair
+ * @qp_num: id of the QP
+ */
+static void irdma_set_cpi_common_values(struct irdma_cq_poll_info *cpi,
+					struct irdma_qp_uk *qp, u32 qp_num)
+{
+	cpi->comp_status = IRDMA_COMPL_STATUS_FLUSHED;
+	cpi->error = true;
+	cpi->major_err = IRDMA_FLUSH_MAJOR_ERR;
+	cpi->minor_err = FLUSH_GENERAL_ERR;
+	cpi->qp_handle = (irdma_qp_handle)(uintptr_t)qp;
+	cpi->qp_id = qp_num;
+}
+
+static inline void irdma_comp_handler(struct irdma_cq *cq)
+{
+	if (!cq->ibcq.comp_handler)
+		return;
+	if (atomic_cmpxchg(&cq->armed, 1, 0))
+		cq->ibcq.comp_handler(&cq->ibcq, cq->ibcq.cq_context);
+}
+
+void irdma_generate_flush_completions(struct irdma_qp *iwqp)
+{
+	struct irdma_qp_uk *qp = &iwqp->sc_qp.qp_uk;
+	struct irdma_ring *sq_ring = &qp->sq_ring;
+	struct irdma_ring *rq_ring = &qp->rq_ring;
+	struct irdma_cmpl_gen *cmpl;
+	__le64 *sw_wqe;
+	u64 wqe_qword;
+	u32 wqe_idx;
+	bool compl_generated = false;
+	unsigned long flags1;
+
+	spin_lock_irqsave(&iwqp->iwscq->lock, flags1);
+	if (irdma_cq_empty(iwqp->iwscq)) {
+		unsigned long flags2;
+
+		spin_lock_irqsave(&iwqp->lock, flags2);
+		while (IRDMA_RING_MORE_WORK(*sq_ring)) {
+			cmpl = kzalloc(sizeof(*cmpl), GFP_ATOMIC);
+			if (!cmpl) {
+				spin_unlock_irqrestore(&iwqp->lock, flags2);
+				spin_unlock_irqrestore(&iwqp->iwscq->lock, flags1);
+				return;
+			}
+
+			wqe_idx = sq_ring->tail;
+			irdma_set_cpi_common_values(&cmpl->cpi, qp, qp->qp_id);
+
+			cmpl->cpi.wr_id = qp->sq_wrtrk_array[wqe_idx].wrid;
+			sw_wqe = qp->sq_base[wqe_idx].elem;
+			get_64bit_val(sw_wqe, 24, &wqe_qword);
+			cmpl->cpi.op_type = (u8)FIELD_GET(IRDMAQPSQ_OPCODE, IRDMAQPSQ_OPCODE);
+			/* remove the SQ WR by moving SQ tail*/
+			IRDMA_RING_SET_TAIL(*sq_ring,
+				sq_ring->tail + qp->sq_wrtrk_array[sq_ring->tail].quanta);
+			if (cmpl->cpi.op_type == IRDMAQP_OP_NOP) {
+				kfree(cmpl);
+				continue;
+			}
+			ibdev_dbg(iwqp->iwscq->ibcq.device,
+				  "DEV: %s: adding wr_id = 0x%llx SQ Completion to list qp_id=%d\n",
+				  __func__, cmpl->cpi.wr_id, qp->qp_id);
+			list_add_tail(&cmpl->list, &iwqp->iwscq->cmpl_generated);
+			compl_generated = true;
+		}
+		spin_unlock_irqrestore(&iwqp->lock, flags2);
+		spin_unlock_irqrestore(&iwqp->iwscq->lock, flags1);
+		if (compl_generated)
+			irdma_comp_handler(iwqp->iwscq);
+	} else {
+		spin_unlock_irqrestore(&iwqp->iwscq->lock, flags1);
+		mod_delayed_work(iwqp->iwdev->cleanup_wq, &iwqp->dwork_flush,
+				 msecs_to_jiffies(IRDMA_FLUSH_DELAY_MS));
+	}
+
+	spin_lock_irqsave(&iwqp->iwrcq->lock, flags1);
+	if (irdma_cq_empty(iwqp->iwrcq)) {
+		unsigned long flags2;
+
+		spin_lock_irqsave(&iwqp->lock, flags2);
+		while (IRDMA_RING_MORE_WORK(*rq_ring)) {
+			cmpl = kzalloc(sizeof(*cmpl), GFP_ATOMIC);
+			if (!cmpl) {
+				spin_unlock_irqrestore(&iwqp->lock, flags2);
+				spin_unlock_irqrestore(&iwqp->iwrcq->lock, flags1);
+				return;
+			}
+
+			wqe_idx = rq_ring->tail;
+			irdma_set_cpi_common_values(&cmpl->cpi, qp, qp->qp_id);
+
+			cmpl->cpi.wr_id = qp->rq_wrid_array[wqe_idx];
+			cmpl->cpi.op_type = IRDMA_OP_TYPE_REC;
+			/* remove the RQ WR by moving RQ tail */
+			IRDMA_RING_SET_TAIL(*rq_ring, rq_ring->tail + 1);
+			ibdev_dbg(iwqp->iwrcq->ibcq.device,
+				  "DEV: %s: adding wr_id = 0x%llx RQ Completion to list qp_id=%d, wqe_idx=%d\n",
+				  __func__, cmpl->cpi.wr_id, qp->qp_id,
+				  wqe_idx);
+			list_add_tail(&cmpl->list, &iwqp->iwrcq->cmpl_generated);
+
+			compl_generated = true;
+		}
+		spin_unlock_irqrestore(&iwqp->lock, flags2);
+		spin_unlock_irqrestore(&iwqp->iwrcq->lock, flags1);
+		if (compl_generated)
+			irdma_comp_handler(iwqp->iwrcq);
+	} else {
+		spin_unlock_irqrestore(&iwqp->iwrcq->lock, flags1);
+		mod_delayed_work(iwqp->iwdev->cleanup_wq, &iwqp->dwork_flush,
+				 msecs_to_jiffies(IRDMA_FLUSH_DELAY_MS));
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/verbs.c
@@ -29,22 +29,25 @@
 	props->vendor_part_id = pcidev->device;
 
 	props->hw_ver = rf->pcidev->revision;
-	props->page_size_cap = SZ_4K | SZ_2M | SZ_1G;
+	props->page_size_cap = hw_attrs->page_size_cap;
 	props->max_mr_size = hw_attrs->max_mr_size;
 	props->max_qp = rf->max_qp - rf->used_qps;
 	props->max_qp_wr = hw_attrs->max_qp_wr;
 	props->max_send_sge = hw_attrs->uk_attrs.max_hw_wq_frags;
 	props->max_recv_sge = hw_attrs->uk_attrs.max_hw_wq_frags;
 	props->max_cq = rf->max_cq - rf->used_cqs;
-	props->max_cqe = rf->max_cqe;
+	props->max_cqe = rf->max_cqe - 1;
 	props->max_mr = rf->max_mr - rf->used_mrs;
 	props->max_mw = props->max_mr;
 	props->max_pd = rf->max_pd - rf->used_pds;
 	props->max_sge_rd = hw_attrs->uk_attrs.max_hw_read_sges;
 	props->max_qp_rd_atom = hw_attrs->max_hw_ird;
 	props->max_qp_init_rd_atom = hw_attrs->max_hw_ord;
-	if (rdma_protocol_roce(ibdev, 1))
+	if (rdma_protocol_roce(ibdev, 1)) {
+		props->device_cap_flags |= IB_DEVICE_RC_RNR_NAK_GEN;
 		props->max_pkeys = IRDMA_PKEY_TBL_SZ;
+	}
+
 	props->max_ah = rf->max_ah;
 	props->max_mcast_grp = rf->max_mcg;
 	props->max_mcast_qp_attach = IRDMA_MAX_MGS_PER_CTX;
@@ -58,36 +61,6 @@
 }
 
 /**
- * irdma_get_eth_speed_and_width - Get IB port speed and width from netdev speed
- * @link_speed: netdev phy link speed
- * @active_speed: IB port speed
- * @active_width: IB port width
- */
-static void irdma_get_eth_speed_and_width(u32 link_speed, u16 *active_speed,
-					  u8 *active_width)
-{
-	if (link_speed <= SPEED_1000) {
-		*active_width = IB_WIDTH_1X;
-		*active_speed = IB_SPEED_SDR;
-	} else if (link_speed <= SPEED_10000) {
-		*active_width = IB_WIDTH_1X;
-		*active_speed = IB_SPEED_FDR10;
-	} else if (link_speed <= SPEED_20000) {
-		*active_width = IB_WIDTH_4X;
-		*active_speed = IB_SPEED_DDR;
-	} else if (link_speed <= SPEED_25000) {
-		*active_width = IB_WIDTH_1X;
-		*active_speed = IB_SPEED_EDR;
-	} else if (link_speed <= SPEED_40000) {
-		*active_width = IB_WIDTH_4X;
-		*active_speed = IB_SPEED_FDR10;
-	} else {
-		*active_width = IB_WIDTH_4X;
-		*active_speed = IB_SPEED_EDR;
-	}
-}
-
-/**
  * irdma_query_port - get port attributes
  * @ibdev: device pointer from stack
  * @port: port number for query
@@ -114,8 +87,9 @@
 		props->state = IB_PORT_DOWN;
 		props->phys_state = IB_PORT_PHYS_STATE_DISABLED;
 	}
-	irdma_get_eth_speed_and_width(SPEED_100000, &props->active_speed,
-				      &props->active_width);
+
+	ib_get_eth_speed(ibdev, port, &props->active_speed,
+			 &props->active_width);
 
 	if (rdma_protocol_roce(ibdev, 1)) {
 		props->gid_tbl_len = 32;
@@ -255,7 +229,7 @@
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_device *iwdev = iwqp->iwdev;
 	struct irdma_sc_qp *qp = &iwqp->sc_qp;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&iwdev->rf->cqp, true);
 	if (!cqp_request)
@@ -532,10 +506,8 @@
 	if (iwqp->iwarp_state == IRDMA_QP_STATE_RTS)
 		irdma_modify_qp_to_err(&iwqp->sc_qp);
 
-	irdma_qp_rem_ref(&iwqp->ibqp);
-	wait_for_completion(&iwqp->free_qp);
-	irdma_free_lsmm_rsrc(iwqp);
-	irdma_cqp_qp_destroy_cmd(&iwdev->rf->sc_dev, &iwqp->sc_qp);
+	if (!iwqp->user_mode)
+		cancel_delayed_work_sync(&iwqp->dwork_flush);
 
 	if (!iwqp->user_mode) {
 		if (iwqp->iwscq) {
@@ -544,6 +516,12 @@
 				irdma_clean_cqes(iwqp, iwqp->iwrcq);
 		}
 	}
+
+	irdma_qp_rem_ref(&iwqp->ibqp);
+	wait_for_completion(&iwqp->free_qp);
+	irdma_free_lsmm_rsrc(iwqp);
+	irdma_cqp_qp_destroy_cmd(&iwdev->rf->sc_dev, &iwqp->sc_qp);
+
 	irdma_remove_push_mmap_entries(iwqp);
 	irdma_free_qp_rsrc(iwqp);
 
@@ -591,7 +569,7 @@
 	u32 sqdepth, rqdepth;
 	u8 sqshift, rqshift;
 	u32 size;
-	enum irdma_status_code status;
+	int status;
 	struct irdma_qp_uk_init_info *ukinfo = &info->qp_uk_init_info;
 	struct irdma_uk_attrs *uk_attrs = &iwdev->rf->sc_dev.hw_attrs.uk_attrs;
 
@@ -667,7 +645,7 @@
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_create_qp_info *qp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&rf->cqp, true);
 	if (!cqp_request)
@@ -771,7 +749,9 @@
 
 	if (init_attr->cap.max_inline_data > uk_attrs->max_hw_inline ||
 	    init_attr->cap.max_send_sge > uk_attrs->max_hw_wq_frags ||
-	    init_attr->cap.max_recv_sge > uk_attrs->max_hw_wq_frags)
+	    init_attr->cap.max_recv_sge > uk_attrs->max_hw_wq_frags ||
+	    init_attr->cap.max_send_wr > uk_attrs->max_hw_wq_quanta ||
+	    init_attr->cap.max_recv_wr > uk_attrs->max_hw_rq_quanta)
 		return -EINVAL;
 
 	if (rdma_protocol_roce(&iwdev->ibdev, 1)) {
@@ -787,6 +767,14 @@
 	return 0;
 }
 
+static void irdma_flush_worker(struct work_struct *work)
+{
+	struct delayed_work *dwork = to_delayed_work(work);
+	struct irdma_qp *iwqp = container_of(dwork, struct irdma_qp, dwork_flush);
+
+	irdma_generate_flush_completions(iwqp);
+}
+
 /**
  * irdma_create_qp - create qp
  * @ibqp: ptr of qp
@@ -805,7 +793,6 @@
 	struct irdma_create_qp_req req;
 	struct irdma_create_qp_resp uresp = {};
 	u32 qp_num = 0;
-	enum irdma_status_code ret;
 	int err_code;
 	int sq_size;
 	int rq_size;
@@ -908,6 +895,7 @@
 		init_info.qp_uk_init_info.abi_ver = iwpd->sc_pd.abi_ver;
 		irdma_setup_virt_qp(iwdev, iwqp, &init_info);
 	} else {
+		INIT_DELAYED_WORK(&iwqp->dwork_flush, irdma_flush_worker);
 		init_info.qp_uk_init_info.abi_ver = IRDMA_ABI_VER;
 		err_code = irdma_setup_kmode_qp(iwdev, iwqp, &init_info, init_attr);
 	}
@@ -936,9 +924,8 @@
 	if (dev->hw_attrs.uk_attrs.hw_rev > IRDMA_GEN_1)
 		init_info.qp_uk_init_info.qp_caps |= IRDMA_PUSH_MODE;
 
-	ret = irdma_sc_qp_init(qp, &init_info);
-	if (ret) {
-		err_code = -EPROTO;
+	err_code = irdma_sc_qp_init(qp, &init_info);
+	if (err_code) {
 		ibdev_dbg(&iwdev->ibdev, "VERBS: qp_init fail\n");
 		goto error;
 	}
@@ -1095,6 +1082,21 @@
 	return 0;
 }
 
+static int irdma_wait_for_suspend(struct irdma_qp *iwqp)
+{
+	if (!wait_event_timeout(iwqp->iwdev->suspend_wq,
+				!iwqp->suspend_pending,
+				msecs_to_jiffies(IRDMA_EVENT_TIMEOUT_MS))) {
+		iwqp->suspend_pending = false;
+		ibdev_warn(&iwqp->iwdev->ibdev,
+			   "modify_qp timed out waiting for suspend. qp_id = %d, last_ae = 0x%x\n",
+			   iwqp->ibqp.qp_num, iwqp->last_aeq);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 /**
  * irdma_modify_qp_roce - modify qp request
  * @ibqp: qp's pointer for modify
@@ -1254,7 +1256,7 @@
 		if (attr->max_dest_rd_atomic > dev->hw_attrs.max_hw_ird) {
 			ibdev_err(&iwdev->ibdev,
 				  "rd_atomic = %d, above max_hw_ird=%d\n",
-				   attr->max_rd_atomic,
+				   attr->max_dest_rd_atomic,
 				   dev->hw_attrs.max_hw_ird);
 			return -EINVAL;
 		}
@@ -1343,17 +1345,11 @@
 
 			info.next_iwarp_state = IRDMA_QP_STATE_SQD;
 			issue_modify_qp = 1;
+			iwqp->suspend_pending = true;
 			break;
 		case IB_QPS_SQE:
 		case IB_QPS_ERR:
 		case IB_QPS_RESET:
-			if (iwqp->iwarp_state == IRDMA_QP_STATE_RTS) {
-				spin_unlock_irqrestore(&iwqp->lock, flags);
-				info.next_iwarp_state = IRDMA_QP_STATE_SQD;
-				irdma_hw_modify_qp(iwdev, iwqp, &info, true);
-				spin_lock_irqsave(&iwqp->lock, flags);
-			}
-
 			if (iwqp->iwarp_state == IRDMA_QP_STATE_ERROR) {
 				spin_unlock_irqrestore(&iwqp->lock, flags);
 				if (udata) {
@@ -1390,6 +1386,11 @@
 			ctx_info->rem_endpoint_idx = udp_info->arp_idx;
 			if (irdma_hw_modify_qp(iwdev, iwqp, &info, true))
 				return -EINVAL;
+			if (info.next_iwarp_state == IRDMA_QP_STATE_SQD) {
+				ret = irdma_wait_for_suspend(iwqp);
+				if (ret)
+					return ret;
+			}
 			spin_lock_irqsave(&iwqp->lock, flags);
 			if (iwqp->iwarp_state == info.curr_iwarp_state) {
 				iwqp->iwarp_state = info.next_iwarp_state;
@@ -1397,11 +1398,11 @@
 			}
 			if (iwqp->ibqp_state > IB_QPS_RTS &&
 			    !iwqp->flush_issued) {
-				iwqp->flush_issued = 1;
 				spin_unlock_irqrestore(&iwqp->lock, flags);
 				irdma_flush_wqes(iwqp, IRDMA_FLUSH_SQ |
 						       IRDMA_FLUSH_RQ |
 						       IRDMA_FLUSH_WAIT);
+				iwqp->flush_issued = 1;
 			} else {
 				spin_unlock_irqrestore(&iwqp->lock, flags);
 			}
@@ -1617,13 +1618,13 @@
 
 	if (issue_modify_qp && iwqp->ibqp_state > IB_QPS_RTS) {
 		if (dont_wait) {
-			if (iwqp->cm_id && iwqp->hw_tcp_state) {
+			if (iwqp->hw_tcp_state) {
 				spin_lock_irqsave(&iwqp->lock, flags);
 				iwqp->hw_tcp_state = IRDMA_TCP_STATE_CLOSED;
 				iwqp->last_aeq = IRDMA_AE_RESET_SENT;
 				spin_unlock_irqrestore(&iwqp->lock, flags);
-				irdma_cm_disconn(iwqp);
 			}
+			irdma_cm_disconn(iwqp);
 		} else {
 			int close_timer_started;
 
@@ -1754,16 +1755,18 @@
 	unsigned long flags;
 
 	spin_lock_irqsave(&iwcq->lock, flags);
+	if (!list_empty(&iwcq->cmpl_generated))
+		irdma_remove_cmpls_list(iwcq);
 	if (!list_empty(&iwcq->resize_list))
 		irdma_process_resize_list(iwcq, iwdev, NULL);
 	spin_unlock_irqrestore(&iwcq->lock, flags);
 
 	irdma_cq_wq_destroy(iwdev->rf, cq);
-	irdma_cq_free_rsrc(iwdev->rf, iwcq);
 
 	spin_lock_irqsave(&iwceq->ce_lock, flags);
 	irdma_sc_cleanup_ceqes(cq, ceq);
 	spin_unlock_irqrestore(&iwceq->ce_lock, flags);
+	irdma_cq_free_rsrc(iwdev->rf, iwcq);
 
 	return 0;
 }
@@ -1789,7 +1792,6 @@
 	struct irdma_device *iwdev;
 	struct irdma_pci_f *rf;
 	struct irdma_cq_buf *cq_buf = NULL;
-	enum irdma_status_code status = 0;
 	unsigned long flags;
 	int ret;
 
@@ -1882,12 +1884,10 @@
 	cqp_info->in.u.cq_modify.cq = &iwcq->sc_cq;
 	cqp_info->in.u.cq_modify.scratch = (uintptr_t)cqp_request;
 	cqp_info->post_sq = 1;
-	status = irdma_handle_cqp_op(rf, cqp_request);
+	ret = irdma_handle_cqp_op(rf, cqp_request);
 	irdma_put_cqp_request(&rf->cqp, cqp_request);
-	if (status) {
-		ret = -EPROTO;
+	if (ret)
 		goto error;
-	}
 
 	spin_lock_irqsave(&iwcq->lock, flags);
 	if (cq_buf) {
@@ -1942,7 +1942,6 @@
 	struct irdma_sc_cq *cq;
 	struct irdma_sc_dev *dev = &rf->sc_dev;
 	struct irdma_cq_init_info info = {};
-	enum irdma_status_code status;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_cq_uk_init_info *ukinfo = &info.cq_uk_init_info;
@@ -1962,6 +1961,7 @@
 	cq->back_cq = iwcq;
 	spin_lock_init(&iwcq->lock);
 	INIT_LIST_HEAD(&iwcq->resize_list);
+	INIT_LIST_HEAD(&iwcq->cmpl_generated);
 	info.dev = dev;
 	ukinfo->cq_size = max(entries, 4);
 	ukinfo->cq_id = cq_num;
@@ -2070,9 +2070,8 @@
 		info.cq_base_pa = iwcq->kmem.pa;
 	}
 
-	if (dev->hw_attrs.uk_attrs.hw_rev >= IRDMA_GEN_2)
-		info.shadow_read_threshold = min(info.cq_uk_init_info.cq_size / 2,
-						 (u32)IRDMA_MAX_CQ_READ_THRESH);
+	info.shadow_read_threshold = min(info.cq_uk_init_info.cq_size / 2,
+					 (u32)IRDMA_MAX_CQ_READ_THRESH);
 
 	if (irdma_sc_cq_init(cq, &info)) {
 		ibdev_dbg(&iwdev->ibdev, "VERBS: init cq fail\n");
@@ -2092,12 +2091,10 @@
 	cqp_info->in.u.cq_create.cq = cq;
 	cqp_info->in.u.cq_create.check_overflow = true;
 	cqp_info->in.u.cq_create.scratch = (uintptr_t)cqp_request;
-	status = irdma_handle_cqp_op(rf, cqp_request);
+	err_code = irdma_handle_cqp_op(rf, cqp_request);
 	irdma_put_cqp_request(&rf->cqp, cqp_request);
-	if (status) {
-		err_code = -ENOMEM;
+	if (err_code)
 		goto cq_free_rsrc;
-	}
 
 	if (udata) {
 		struct irdma_create_cq_resp resp = {};
@@ -2298,20 +2295,21 @@
  * @rf: RDMA PCI function
  * @iwmr: mr pointer for this memory registration
  * @use_pbles: flag if to use pble's
+ * @lvl_1_only: request only level 1 pble if true
  */
 static int irdma_setup_pbles(struct irdma_pci_f *rf, struct irdma_mr *iwmr,
-			     bool use_pbles)
+			     bool use_pbles, bool lvl_1_only)
 {
 	struct irdma_pbl *iwpbl = &iwmr->iwpbl;
 	struct irdma_pble_alloc *palloc = &iwpbl->pble_alloc;
 	struct irdma_pble_info *pinfo;
 	u64 *pbl;
-	enum irdma_status_code status;
+	int status;
 	enum irdma_pble_level level = PBLE_LEVEL_1;
 
 	if (use_pbles) {
 		status = irdma_get_pble(rf->pble_rsrc, palloc, iwmr->page_cnt,
-					false);
+					lvl_1_only);
 		if (status)
 			return -ENOMEM;
 
@@ -2354,16 +2352,10 @@
 	bool ret = true;
 
 	pg_size = iwmr->page_size;
-	err = irdma_setup_pbles(iwdev->rf, iwmr, use_pbles);
+	err = irdma_setup_pbles(iwdev->rf, iwmr, use_pbles, true);
 	if (err)
 		return err;
 
-	if (use_pbles && palloc->level != PBLE_LEVEL_1) {
-		irdma_free_pble(iwdev->rf->pble_rsrc, palloc);
-		iwpbl->pbl_allocated = false;
-		return -ENOMEM;
-	}
-
 	if (use_pbles)
 		arr = palloc->level1.addr;
 
@@ -2431,7 +2423,7 @@
 	struct irdma_pd *iwpd = to_iwpd(iwmr->ibmr.pd);
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&iwdev->rf->cqp, true);
 	if (!cqp_request)
@@ -2506,7 +2498,7 @@
 	cqp_info = &cqp_request->info;
 	info = &cqp_info->in.u.dealloc_stag.info;
 	memset(info, 0, sizeof(*info));
-	info->pd_id = iwpd->sc_pd.pd_id & 0x00007fff;
+	info->pd_id = iwpd->sc_pd.pd_id;
 	info->stag_idx = ibmw->rkey >> IRDMA_CQPSQ_STAG_IDX_S;
 	info->mr = false;
 	cqp_info->cqp_cmd = IRDMA_OP_DEALLOC_STAG;
@@ -2529,9 +2521,9 @@
 			       struct irdma_mr *iwmr)
 {
 	struct irdma_allocate_stag_info *info;
-	struct irdma_pd *iwpd = to_iwpd(iwmr->ibmr.pd);
-	enum irdma_status_code status;
-	int err = 0;
+	struct ib_pd *pd = iwmr->ibmr.pd;
+	struct irdma_pd *iwpd = to_iwpd(pd);
+	int status;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
 
@@ -2546,6 +2538,7 @@
 	info->stag_idx = iwmr->stag >> IRDMA_CQPSQ_STAG_IDX_S;
 	info->pd_id = iwpd->sc_pd.pd_id;
 	info->total_len = iwmr->len;
+	info->all_memory = pd->flags & IB_PD_UNSAFE_GLOBAL_RKEY;
 	info->remote_access = true;
 	cqp_info->cqp_cmd = IRDMA_OP_ALLOC_STAG;
 	cqp_info->post_sq = 1;
@@ -2553,10 +2546,8 @@
 	cqp_info->in.u.alloc_stag.scratch = (uintptr_t)cqp_request;
 	status = irdma_handle_cqp_op(iwdev->rf, cqp_request);
 	irdma_put_cqp_request(&iwdev->rf->cqp, cqp_request);
-	if (status)
-		err = -ENOMEM;
 
-	return err;
+	return status;
 }
 
 /**
@@ -2572,9 +2563,8 @@
 	struct irdma_pble_alloc *palloc;
 	struct irdma_pbl *iwpbl;
 	struct irdma_mr *iwmr;
-	enum irdma_status_code status;
 	u32 stag;
-	int err_code = -ENOMEM;
+	int err_code;
 
 	iwmr = kzalloc(sizeof(*iwmr), GFP_KERNEL);
 	if (!iwmr)
@@ -2596,9 +2586,11 @@
 	iwmr->type = IRDMA_MEMREG_TYPE_MEM;
 	palloc = &iwpbl->pble_alloc;
 	iwmr->page_cnt = max_num_sg;
-	status = irdma_get_pble(iwdev->rf->pble_rsrc, palloc, iwmr->page_cnt,
-				true);
-	if (status)
+	/* Use system PAGE_SIZE as the sg page sizes are unknown at this point */
+	iwmr->len = max_num_sg * PAGE_SIZE;
+	err_code = irdma_get_pble(iwdev->rf->pble_rsrc, palloc, iwmr->page_cnt,
+				  true);
+	if (err_code)
 		goto err_get_pble;
 
 	err_code = irdma_hw_alloc_stag(iwdev, iwmr);
@@ -2667,12 +2659,12 @@
 {
 	struct irdma_pbl *iwpbl = &iwmr->iwpbl;
 	struct irdma_reg_ns_stag_info *stag_info;
-	struct irdma_pd *iwpd = to_iwpd(iwmr->ibmr.pd);
+	struct ib_pd *pd = iwmr->ibmr.pd;
+	struct irdma_pd *iwpd = to_iwpd(pd);
 	struct irdma_pble_alloc *palloc = &iwpbl->pble_alloc;
-	enum irdma_status_code status;
-	int err = 0;
 	struct irdma_cqp_request *cqp_request;
 	struct cqp_cmds_info *cqp_info;
+	int ret;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&iwdev->rf->cqp, true);
 	if (!cqp_request)
@@ -2687,6 +2679,7 @@
 	stag_info->total_len = iwmr->len;
 	stag_info->access_rights = irdma_get_mr_access(access);
 	stag_info->pd_id = iwpd->sc_pd.pd_id;
+	stag_info->all_memory = pd->flags & IB_PD_UNSAFE_GLOBAL_RKEY;
 	if (stag_info->access_rights & IRDMA_ACCESS_FLAGS_ZERO_BASED)
 		stag_info->addr_type = IRDMA_ADDR_TYPE_ZERO_BASED;
 	else
@@ -2709,12 +2702,10 @@
 	cqp_info->post_sq = 1;
 	cqp_info->in.u.mr_reg_non_shared.dev = &iwdev->rf->sc_dev;
 	cqp_info->in.u.mr_reg_non_shared.scratch = (uintptr_t)cqp_request;
-	status = irdma_handle_cqp_op(iwdev->rf, cqp_request);
+	ret = irdma_handle_cqp_op(iwdev->rf, cqp_request);
 	irdma_put_cqp_request(&iwdev->rf->cqp, cqp_request);
-	if (status)
-		err = -ENOMEM;
 
-	return err;
+	return ret;
 }
 
 /**
@@ -2776,7 +2767,7 @@
 
 	if (req.reg_type == IRDMA_MEMREG_TYPE_MEM) {
 		iwmr->page_size = ib_umem_find_best_pgsz(region,
-							 SZ_4K | SZ_2M | SZ_1G,
+							 iwdev->rf->sc_dev.hw_attrs.page_size_cap,
 							 virt);
 		if (unlikely(!iwmr->page_size)) {
 			kfree(iwmr);
@@ -2834,7 +2825,7 @@
 	case IRDMA_MEMREG_TYPE_MEM:
 		use_pbles = (iwmr->page_cnt != 1);
 
-		err = irdma_setup_pbles(iwdev->rf, iwmr, use_pbles);
+		err = irdma_setup_pbles(iwdev->rf, iwmr, use_pbles, false);
 		if (err)
 			goto error;
 
@@ -2894,7 +2885,6 @@
 	struct irdma_device *iwdev = to_iwdev(pd->device);
 	struct irdma_pbl *iwpbl;
 	struct irdma_mr *iwmr;
-	enum irdma_status_code status;
 	u32 stag;
 	int ret;
 
@@ -2922,10 +2912,9 @@
 	iwmr->pgaddrmem[0] = addr;
 	iwmr->len = size;
 	iwmr->page_size = SZ_4K;
-	status = irdma_hwreg_mr(iwdev, iwmr, access);
-	if (status) {
+	ret = irdma_hwreg_mr(iwdev, iwmr, access);
+	if (ret) {
 		irdma_free_stag(iwdev, stag);
-		ret = -ENOMEM;
 		goto err;
 	}
 
@@ -3018,7 +3007,7 @@
 	cqp_info = &cqp_request->info;
 	info = &cqp_info->in.u.dealloc_stag.info;
 	memset(info, 0, sizeof(*info));
-	info->pd_id = iwpd->sc_pd.pd_id & 0x00007fff;
+	info->pd_id = iwpd->sc_pd.pd_id;
 	info->stag_idx = ib_mr->rkey >> IRDMA_CQPSQ_STAG_IDX_S;
 	info->mr = true;
 	if (iwpbl->pbl_allocated)
@@ -3041,24 +3030,6 @@
 }
 
 /**
- * irdma_copy_sg_list - copy sg list for qp
- * @sg_list: copied into sg_list
- * @sgl: copy from sgl
- * @num_sges: count of sg entries
- */
-static void irdma_copy_sg_list(struct irdma_sge *sg_list, struct ib_sge *sgl,
-			       int num_sges)
-{
-	unsigned int i;
-
-	for (i = 0; (i < num_sges) && (i < IRDMA_MAX_WQ_FRAGMENT_COUNT); i++) {
-		sg_list[i].tag_off = sgl[i].addr;
-		sg_list[i].len = sgl[i].length;
-		sg_list[i].stag = sgl[i].lkey;
-	}
-}
-
-/**
  * irdma_post_send -  kernel application wr
  * @ibqp: qp ptr for wr
  * @ib_wr: work request ptr
@@ -3072,20 +3043,16 @@
 	struct irdma_qp_uk *ukqp;
 	struct irdma_sc_dev *dev;
 	struct irdma_post_sq_info info;
-	enum irdma_status_code ret;
 	int err = 0;
 	unsigned long flags;
 	bool inv_stag;
 	struct irdma_ah *ah;
-	bool reflush = false;
 
 	iwqp = to_iwqp(ibqp);
 	ukqp = &iwqp->sc_qp.qp_uk;
 	dev = &iwqp->iwdev->rf->sc_dev;
 
 	spin_lock_irqsave(&iwqp->lock, flags);
-	if (iwqp->flush_issued && ukqp->sq_flush_complete)
-		reflush = true;
 	while (ib_wr) {
 		memset(&info, 0, sizeof(info));
 		inv_stag = false;
@@ -3131,11 +3098,10 @@
 					info.op.inline_send.qkey = ud_wr(ib_wr)->remote_qkey;
 					info.op.inline_send.dest_qp = ud_wr(ib_wr)->remote_qpn;
 				}
-				ret = irdma_uk_inline_send(ukqp, &info, false);
+				err = irdma_uk_inline_send(ukqp, &info, false);
 			} else {
 				info.op.send.num_sges = ib_wr->num_sge;
-				info.op.send.sg_list = (struct irdma_sge *)
-						       ib_wr->sg_list;
+				info.op.send.sg_list = ib_wr->sg_list;
 				if (iwqp->ibqp.qp_type == IB_QPT_UD ||
 				    iwqp->ibqp.qp_type == IB_QPT_GSI) {
 					ah = to_iwah(ud_wr(ib_wr)->ah);
@@ -3143,14 +3109,7 @@
 					info.op.send.qkey = ud_wr(ib_wr)->remote_qkey;
 					info.op.send.dest_qp = ud_wr(ib_wr)->remote_qpn;
 				}
-				ret = irdma_uk_send(ukqp, &info, false);
-			}
-
-			if (ret) {
-				if (ret == IRDMA_ERR_QP_TOOMANY_WRS_POSTED)
-					err = -ENOMEM;
-				else
-					err = -EINVAL;
+				err = irdma_uk_send(ukqp, &info, false);
 			}
 			break;
 		case IB_WR_RDMA_WRITE_WITH_IMM:
@@ -3170,23 +3129,19 @@
 
 			if (ib_wr->send_flags & IB_SEND_INLINE) {
 				info.op.inline_rdma_write.data = (void *)(uintptr_t)ib_wr->sg_list[0].addr;
-				info.op.inline_rdma_write.len = ib_wr->sg_list[0].length;
-				info.op.inline_rdma_write.rem_addr.tag_off = rdma_wr(ib_wr)->remote_addr;
-				info.op.inline_rdma_write.rem_addr.stag = rdma_wr(ib_wr)->rkey;
-				ret = irdma_uk_inline_rdma_write(ukqp, &info, false);
+				info.op.inline_rdma_write.len =
+						ib_wr->sg_list[0].length;
+				info.op.inline_rdma_write.rem_addr.addr =
+						rdma_wr(ib_wr)->remote_addr;
+				info.op.inline_rdma_write.rem_addr.lkey =
+						rdma_wr(ib_wr)->rkey;
+				err = irdma_uk_inline_rdma_write(ukqp, &info, false);
 			} else {
 				info.op.rdma_write.lo_sg_list = (void *)ib_wr->sg_list;
 				info.op.rdma_write.num_lo_sges = ib_wr->num_sge;
-				info.op.rdma_write.rem_addr.tag_off = rdma_wr(ib_wr)->remote_addr;
-				info.op.rdma_write.rem_addr.stag = rdma_wr(ib_wr)->rkey;
-				ret = irdma_uk_rdma_write(ukqp, &info, false);
-			}
-
-			if (ret) {
-				if (ret == IRDMA_ERR_QP_TOOMANY_WRS_POSTED)
-					err = -ENOMEM;
-				else
-					err = -EINVAL;
+				info.op.rdma_write.rem_addr.addr = rdma_wr(ib_wr)->remote_addr;
+				info.op.rdma_write.rem_addr.lkey = rdma_wr(ib_wr)->rkey;
+				err = irdma_uk_rdma_write(ukqp, &info, false);
 			}
 			break;
 		case IB_WR_RDMA_READ_WITH_INV:
@@ -3199,25 +3154,17 @@
 				break;
 			}
 			info.op_type = IRDMA_OP_TYPE_RDMA_READ;
-			info.op.rdma_read.rem_addr.tag_off = rdma_wr(ib_wr)->remote_addr;
-			info.op.rdma_read.rem_addr.stag = rdma_wr(ib_wr)->rkey;
+			info.op.rdma_read.rem_addr.addr = rdma_wr(ib_wr)->remote_addr;
+			info.op.rdma_read.rem_addr.lkey = rdma_wr(ib_wr)->rkey;
 			info.op.rdma_read.lo_sg_list = (void *)ib_wr->sg_list;
 			info.op.rdma_read.num_lo_sges = ib_wr->num_sge;
-
-			ret = irdma_uk_rdma_read(ukqp, &info, inv_stag, false);
-			if (ret) {
-				if (ret == IRDMA_ERR_QP_TOOMANY_WRS_POSTED)
-					err = -ENOMEM;
-				else
-					err = -EINVAL;
-			}
+			err = irdma_uk_rdma_read(ukqp, &info, inv_stag, false);
 			break;
 		case IB_WR_LOCAL_INV:
 			info.op_type = IRDMA_OP_TYPE_INV_STAG;
+			info.local_fence = info.read_fence;
 			info.op.inv_local_stag.target_stag = ib_wr->ex.invalidate_rkey;
-			ret = irdma_uk_stag_local_invalidate(ukqp, &info, true);
-			if (ret)
-				err = -ENOMEM;
+			err = irdma_uk_stag_local_invalidate(ukqp, &info, true);
 			break;
 		case IB_WR_REG_MR: {
 			struct irdma_mr *iwmr = to_iwmr(reg_wr(ib_wr)->mr);
@@ -3239,10 +3186,8 @@
 			stag_info.local_fence = ib_wr->send_flags & IB_SEND_FENCE;
 			if (iwmr->npages > IRDMA_MIN_PAGES_PER_FMR)
 				stag_info.chunk_size = 1;
-			ret = irdma_sc_mr_fast_register(&iwqp->sc_qp, &stag_info,
+			err = irdma_sc_mr_fast_register(&iwqp->sc_qp, &stag_info,
 							true);
-			if (ret)
-				err = -ENOMEM;
 			break;
 		}
 		default:
@@ -3258,15 +3203,14 @@
 		ib_wr = ib_wr->next;
 	}
 
-	if (!iwqp->flush_issued && iwqp->hw_iwarp_state <= IRDMA_QP_STATE_RTS) {
-		irdma_uk_qp_post_wr(ukqp);
+	if (!iwqp->flush_issued) {
+		if (iwqp->hw_iwarp_state <= IRDMA_QP_STATE_RTS)
+			irdma_uk_qp_post_wr(ukqp);
 		spin_unlock_irqrestore(&iwqp->lock, flags);
-	} else if (reflush) {
-		ukqp->sq_flush_complete = false;
-		spin_unlock_irqrestore(&iwqp->lock, flags);
-		irdma_flush_wqes(iwqp, IRDMA_FLUSH_SQ | IRDMA_REFLUSH);
 	} else {
 		spin_unlock_irqrestore(&iwqp->lock, flags);
+		mod_delayed_work(iwqp->iwdev->cleanup_wq, &iwqp->dwork_flush,
+				 msecs_to_jiffies(IRDMA_FLUSH_DELAY_MS));
 	}
 	if (err)
 		*bad_wr = ib_wr;
@@ -3287,31 +3231,21 @@
 	struct irdma_qp *iwqp;
 	struct irdma_qp_uk *ukqp;
 	struct irdma_post_rq_info post_recv = {};
-	struct irdma_sge sg_list[IRDMA_MAX_WQ_FRAGMENT_COUNT];
-	enum irdma_status_code ret = 0;
 	unsigned long flags;
 	int err = 0;
-	bool reflush = false;
 
 	iwqp = to_iwqp(ibqp);
 	ukqp = &iwqp->sc_qp.qp_uk;
 
 	spin_lock_irqsave(&iwqp->lock, flags);
-	if (iwqp->flush_issued && ukqp->rq_flush_complete)
-		reflush = true;
 	while (ib_wr) {
 		post_recv.num_sges = ib_wr->num_sge;
 		post_recv.wr_id = ib_wr->wr_id;
-		irdma_copy_sg_list(sg_list, ib_wr->sg_list, ib_wr->num_sge);
-		post_recv.sg_list = sg_list;
-		ret = irdma_uk_post_receive(ukqp, &post_recv);
-		if (ret) {
+		post_recv.sg_list = ib_wr->sg_list;
+		err = irdma_uk_post_receive(ukqp, &post_recv);
+		if (err) {
 			ibdev_dbg(&iwqp->iwdev->ibdev,
-				  "VERBS: post_recv err %d\n", ret);
-			if (ret == IRDMA_ERR_QP_TOOMANY_WRS_POSTED)
-				err = -ENOMEM;
-			else
-				err = -EINVAL;
+				  "VERBS: post_recv err %d\n", err);
 			goto out;
 		}
 
@@ -3319,13 +3253,10 @@
 	}
 
 out:
-	if (reflush) {
-		ukqp->rq_flush_complete = false;
-		spin_unlock_irqrestore(&iwqp->lock, flags);
-		irdma_flush_wqes(iwqp, IRDMA_FLUSH_RQ | IRDMA_REFLUSH);
-	} else {
-		spin_unlock_irqrestore(&iwqp->lock, flags);
-	}
+	spin_unlock_irqrestore(&iwqp->lock, flags);
+	if (iwqp->flush_issued)
+		mod_delayed_work(iwqp->iwdev->cleanup_wq, &iwqp->dwork_flush,
+				 msecs_to_jiffies(IRDMA_FLUSH_DELAY_MS));
 
 	if (err)
 		*bad_wr = ib_wr;
@@ -3356,6 +3287,8 @@
 		return IB_WC_RETRY_EXC_ERR;
 	case FLUSH_MW_BIND_ERR:
 		return IB_WC_MW_BIND_ERR;
+	case FLUSH_REM_INV_REQ_ERR:
+		return IB_WC_REM_INV_REQ_ERR;
 	case FLUSH_FATAL_ERR:
 	default:
 		return IB_WC_FATAL_ERR;
@@ -3498,7 +3431,7 @@
 	struct irdma_cq_buf *last_buf = NULL;
 	struct irdma_cq_poll_info *cur_cqe = &iwcq->cur_cqe;
 	struct irdma_cq_buf *cq_buf;
-	enum irdma_status_code ret;
+	int ret;
 	struct irdma_device *iwdev;
 	struct irdma_cq_uk *ukcq;
 	bool cq_new_cqe = false;
@@ -3518,10 +3451,10 @@
 				cq_new_cqe = true;
 				continue;
 			}
-			if (ret == IRDMA_ERR_Q_EMPTY)
+			if (ret == -ENOENT)
 				break;
 			 /* QP using the CQ is destroyed. Skip reporting this CQE */
-			if (ret == IRDMA_ERR_Q_DESTROYED) {
+			if (ret == -EFAULT) {
 				cq_new_cqe = true;
 				continue;
 			}
@@ -3537,16 +3470,21 @@
 	/* check the current CQ for new cqes */
 	while (npolled < num_entries) {
 		ret = irdma_poll_one(ukcq, cur_cqe, entry + npolled);
+		if (ret == -ENOENT) {
+			ret = irdma_generated_cmpls(iwcq, cur_cqe);
+			if (!ret)
+				irdma_process_cqe(entry + npolled, cur_cqe);
+		}
 		if (!ret) {
 			++npolled;
 			cq_new_cqe = true;
 			continue;
 		}
 
-		if (ret == IRDMA_ERR_Q_EMPTY)
+		if (ret == -ENOENT)
 			break;
 		/* QP using the CQ is destroyed. Skip reporting this CQE */
-		if (ret == IRDMA_ERR_Q_DESTROYED) {
+		if (ret == -EFAULT) {
 			cq_new_cqe = true;
 			continue;
 		}
@@ -3604,18 +3542,31 @@
 	struct irdma_cq *iwcq;
 	struct irdma_cq_uk *ukcq;
 	unsigned long flags;
-	enum irdma_cmpl_notify cq_notify = IRDMA_CQ_COMPL_EVENT;
+	enum irdma_cmpl_notify cq_notify;
+	bool promo_event = false;
+	int ret = 0;
 
+	cq_notify = notify_flags == IB_CQ_SOLICITED ?
+		    IRDMA_CQ_COMPL_SOLICITED : IRDMA_CQ_COMPL_EVENT;
 	iwcq = to_iwcq(ibcq);
 	ukcq = &iwcq->sc_cq.cq_uk;
-	if (notify_flags == IB_CQ_SOLICITED)
-		cq_notify = IRDMA_CQ_COMPL_SOLICITED;
 
 	spin_lock_irqsave(&iwcq->lock, flags);
-	irdma_uk_cq_request_notification(ukcq, cq_notify);
+	/* Only promote to arm the CQ for any event if the last arm event was solicited. */
+	if (iwcq->last_notify == IRDMA_CQ_COMPL_SOLICITED && notify_flags != IB_CQ_SOLICITED)
+		promo_event = true;
+
+	if (!atomic_cmpxchg(&iwcq->armed, 0, 1) || promo_event) {
+		iwcq->last_notify = cq_notify;
+		irdma_uk_cq_request_notification(ukcq, cq_notify);
+	}
+
+	if ((notify_flags & IB_CQ_REPORT_MISSED_EVENTS) &&
+	    (!irdma_cq_empty(iwcq) || !list_empty(&iwcq->cmpl_generated)))
+		ret = 1;
 	spin_unlock_irqrestore(&iwcq->lock, flags);
 
-	return 0;
+	return ret;
 }
 
 static int irdma_roce_port_immutable(struct ib_device *ibdev, u32 port_num,
@@ -3861,7 +3812,7 @@
 {
 	struct cqp_cmds_info *cqp_info;
 	struct irdma_cqp_request *cqp_request;
-	enum irdma_status_code status;
+	int status;
 
 	cqp_request = irdma_alloc_and_get_cqp_request(&iwdev->rf->cqp, true);
 	if (!cqp_request)
@@ -4314,7 +4265,6 @@
 		ah_attr->grh.traffic_class = ah->sc_ah.ah_info.tc_tos;
 		ah_attr->grh.hop_limit = ah->sc_ah.ah_info.hop_ttl;
 		ah_attr->grh.sgid_index = ah->sgid_index;
-		ah_attr->grh.sgid_index = ah->sgid_index;
 		memcpy(&ah_attr->grh.dgid, &ah->dgid,
 		       sizeof(ah_attr->grh.dgid));
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/verbs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/verbs.h
@@ -4,6 +4,7 @@
 #define IRDMA_VERBS_H
 
 #define IRDMA_MAX_SAVED_PHY_PGADDR	4
+#define IRDMA_FLUSH_DELAY_MS		20
 
 #define IRDMA_PKEY_TBL_SZ		1
 #define IRDMA_DEFAULT_PKEY		0xFFFF
@@ -110,6 +111,8 @@
 	u16 cq_size;
 	u16 cq_num;
 	bool user_mode;
+	atomic_t armed;
+	enum irdma_cmpl_notify last_notify;
 	u32 polled_cmpls;
 	u32 cq_mem_size;
 	struct irdma_dma_mem kmem;
@@ -119,6 +122,12 @@
 	struct irdma_pbl *iwpbl_shadow;
 	struct list_head resize_list;
 	struct irdma_cq_poll_info cur_cqe;
+	struct list_head cmpl_generated;
+};
+
+struct irdma_cmpl_gen {
+	struct list_head list;
+	struct irdma_cq_poll_info cpi;
 };
 
 struct disconn_work {
@@ -159,6 +168,7 @@
 	refcount_t refcnt;
 	struct iw_cm_id *cm_id;
 	struct irdma_cm_node *cm_node;
+	struct delayed_work dwork_flush;
 	struct ib_mr *lsmm_mr;
 	atomic_t hw_mod_qp_pend;
 	enum ib_qp_state ibqp_state;
@@ -178,6 +188,7 @@
 	u8 flush_issued : 1;
 	u8 sig_all : 1;
 	u8 pau_mode : 1;
+	u8 suspend_pending : 1;
 	u8 rsvd : 1;
 	u8 iwarp_state;
 	u16 term_sq_flush_code;
@@ -222,4 +233,7 @@
 void irdma_ib_unregister_device(struct irdma_device *iwdev);
 void irdma_ib_dealloc_device(struct ib_device *ibdev);
 void irdma_ib_qp_event(struct irdma_qp *iwqp, enum irdma_qp_event_type event);
+void irdma_generate_flush_completions(struct irdma_qp *iwqp);
+void irdma_remove_cmpls_list(struct irdma_cq *iwcq);
+int irdma_generated_cmpls(struct irdma_cq *iwcq, struct irdma_cq_poll_info *cq_poll_info);
 #endif /* IRDMA_VERBS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/ws.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/ws.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 or Linux-OpenIB
 /* Copyright (c) 2017 - 2021 Intel Corporation */
 #include "osdep.h"
-#include "status.h"
 #include "hmc.h"
 #include "defs.h"
 #include "type.h"
@@ -87,8 +86,8 @@
  * @node: pointer to node
  * @cmd: add, remove or modify
  */
-static enum irdma_status_code
-irdma_ws_cqp_cmd(struct irdma_sc_vsi *vsi, struct irdma_ws_node *node, u8 cmd)
+static int irdma_ws_cqp_cmd(struct irdma_sc_vsi *vsi,
+			    struct irdma_ws_node *node, u8 cmd)
 {
 	struct irdma_ws_node_info node_info = {};
 
@@ -106,7 +105,7 @@
 	node_info.enable = node->enable;
 	if (irdma_cqp_ws_node_cmd(vsi->dev, cmd, &node_info)) {
 		ibdev_dbg(to_ibdev(vsi->dev), "WS: CQP WS CMD failed\n");
-		return IRDMA_ERR_NO_MEMORY;
+		return -ENOMEM;
 	}
 
 	if (node->type_leaf && cmd == IRDMA_OP_WS_ADD_NODE) {
@@ -234,18 +233,18 @@
  * @vsi: vsi pointer
  * @user_pri: user priority
  */
-enum irdma_status_code irdma_ws_add(struct irdma_sc_vsi *vsi, u8 user_pri)
+int irdma_ws_add(struct irdma_sc_vsi *vsi, u8 user_pri)
 {
 	struct irdma_ws_node *ws_tree_root;
 	struct irdma_ws_node *vsi_node;
 	struct irdma_ws_node *tc_node;
 	u16 traffic_class;
-	enum irdma_status_code ret = 0;
+	int ret = 0;
 	int i;
 
 	mutex_lock(&vsi->dev->ws_mutex);
 	if (vsi->tc_change_pending) {
-		ret = IRDMA_ERR_NOT_READY;
+		ret = -EBUSY;
 		goto exit;
 	}
 
@@ -258,7 +257,7 @@
 		ws_tree_root = irdma_alloc_node(vsi, user_pri,
 						WS_NODE_TYPE_PARENT, NULL);
 		if (!ws_tree_root) {
-			ret = IRDMA_ERR_NO_MEMORY;
+			ret = -ENOMEM;
 			goto exit;
 		}
 
@@ -283,7 +282,7 @@
 		vsi_node = irdma_alloc_node(vsi, user_pri, WS_NODE_TYPE_PARENT,
 					    ws_tree_root);
 		if (!vsi_node) {
-			ret = IRDMA_ERR_NO_MEMORY;
+			ret = -ENOMEM;
 			goto vsi_add_err;
 		}
 
@@ -310,7 +309,7 @@
 		tc_node = irdma_alloc_node(vsi, user_pri, WS_NODE_TYPE_LEAF,
 					   vsi_node);
 		if (!tc_node) {
-			ret = IRDMA_ERR_NO_MEMORY;
+			ret = -ENOMEM;
 			goto leaf_add_err;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/irdma/ws.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/irdma/ws.h
@@ -34,7 +34,7 @@
 };
 
 struct irdma_sc_vsi;
-enum irdma_status_code irdma_ws_add(struct irdma_sc_vsi *vsi, u8 user_pri);
+int irdma_ws_add(struct irdma_sc_vsi *vsi, u8 user_pri);
 void irdma_ws_remove(struct irdma_sc_vsi *vsi, u8 user_pri);
 void irdma_ws_reset(struct irdma_sc_vsi *vsi);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx4/alias_GUID.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx4/alias_GUID.c
@@ -832,7 +832,7 @@
 
 int mlx4_ib_init_alias_guid_service(struct mlx4_ib_dev *dev)
 {
-	char alias_wq_name[15];
+	char alias_wq_name[22];
 	int ret = 0;
 	int i, j;
 	union ib_gid gid;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx4/mad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx4/mad.c
@@ -2158,7 +2158,7 @@
 				       struct mlx4_ib_demux_ctx *ctx,
 				       int port)
 {
-	char name[12];
+	char name[21];
 	int ret = 0;
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx4/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx4/main.c
@@ -392,10 +392,10 @@
 	}
 	spin_unlock_bh(&iboe->lock);
 
-	if (!ret && hw_update) {
+	if (gids)
 		ret = mlx4_ib_update_gids(gids, ibdev, attr->port_num);
-		kfree(gids);
-	}
+
+	kfree(gids);
 	return ret;
 }
 
@@ -2217,6 +2217,11 @@
 	.get_hw_stats = mlx4_ib_get_hw_stats,
 };
 
+static const struct ib_device_ops mlx4_ib_hw_stats_ops1 = {
+	.alloc_hw_device_stats = mlx4_ib_alloc_hw_device_stats,
+	.get_hw_stats = mlx4_ib_get_hw_stats,
+};
+
 static int mlx4_ib_alloc_diag_counters(struct mlx4_ib_dev *ibdev)
 {
 	struct mlx4_ib_diag_counters *diag = ibdev->diag_counters;
@@ -2229,9 +2234,16 @@
 		return 0;
 
 	for (i = 0; i < MLX4_DIAG_COUNTERS_TYPES; i++) {
-		/* i == 1 means we are building port counters */
-		if (i && !per_port)
-			continue;
+		/*
+		 * i == 1 means we are building port counters, set a different
+		 * stats ops without port stats callback.
+		 */
+		if (i && !per_port) {
+			ib_set_device_ops(&ibdev->ib_dev,
+					  &mlx4_ib_hw_stats_ops1);
+
+			return 0;
+		}
 
 		ret = __mlx4_ib_alloc_diag_counters(ibdev, &diag[i].name,
 						    &diag[i].offset,
@@ -3237,7 +3249,7 @@
 	case MLX4_DEV_EVENT_PORT_MGMT_CHANGE:
 		ew = kmalloc(sizeof *ew, GFP_ATOMIC);
 		if (!ew)
-			break;
+			return;
 
 		INIT_WORK(&ew->work, handle_port_mgmt_change_event);
 		memcpy(&ew->ib_eqe, eqe, sizeof *eqe);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx4/mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx4/mr.c
@@ -439,7 +439,6 @@
 		goto err_mr;
 
 	mr->ibmr.rkey = mr->ibmr.lkey = mr->mmr.key;
-	mr->ibmr.length = length;
 	mr->ibmr.page_size = 1U << shift;
 
 	return &mr->ibmr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx4/qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx4/qp.c
@@ -412,9 +412,13 @@
 			    struct mlx4_ib_qp *qp,
 			    struct mlx4_ib_create_qp *ucmd)
 {
+	u32 cnt;
+
 	/* Sanity check SQ size before proceeding */
-	if ((1 << ucmd->log_sq_bb_count) > dev->dev->caps.max_wqes	 ||
-	    ucmd->log_sq_stride >
+	if (check_shl_overflow(1, ucmd->log_sq_bb_count, &cnt) ||
+	    cnt > dev->dev->caps.max_wqes)
+		return -EINVAL;
+	if (ucmd->log_sq_stride >
 		ilog2(roundup_pow_of_two(dev->dev->caps.max_sq_desc_sz)) ||
 	    ucmd->log_sq_stride < MLX4_IB_MIN_SQ_STRIDE)
 		return -EINVAL;
@@ -526,15 +530,15 @@
 		return (-EOPNOTSUPP);
 	}
 
-	if (ucmd->rx_hash_fields_mask & ~(MLX4_IB_RX_HASH_SRC_IPV4	|
-					  MLX4_IB_RX_HASH_DST_IPV4	|
-					  MLX4_IB_RX_HASH_SRC_IPV6	|
-					  MLX4_IB_RX_HASH_DST_IPV6	|
-					  MLX4_IB_RX_HASH_SRC_PORT_TCP	|
-					  MLX4_IB_RX_HASH_DST_PORT_TCP	|
-					  MLX4_IB_RX_HASH_SRC_PORT_UDP	|
-					  MLX4_IB_RX_HASH_DST_PORT_UDP  |
-					  MLX4_IB_RX_HASH_INNER)) {
+	if (ucmd->rx_hash_fields_mask & ~(u64)(MLX4_IB_RX_HASH_SRC_IPV4	|
+					       MLX4_IB_RX_HASH_DST_IPV4	|
+					       MLX4_IB_RX_HASH_SRC_IPV6	|
+					       MLX4_IB_RX_HASH_DST_IPV6	|
+					       MLX4_IB_RX_HASH_SRC_PORT_TCP |
+					       MLX4_IB_RX_HASH_DST_PORT_TCP |
+					       MLX4_IB_RX_HASH_SRC_PORT_UDP |
+					       MLX4_IB_RX_HASH_DST_PORT_UDP |
+					       MLX4_IB_RX_HASH_INNER)) {
 		pr_debug("RX Hash fields_mask has unsupported mask (0x%llx)\n",
 			 ucmd->rx_hash_fields_mask);
 		return (-EOPNOTSUPP);
@@ -1099,8 +1103,10 @@
 			if (dev->steering_support ==
 			    MLX4_STEERING_MODE_DEVICE_MANAGED)
 				qp->flags |= MLX4_IB_QP_NETIF;
-			else
+			else {
+				err = -EINVAL;
 				goto err;
+			}
 		}
 
 		err = set_kernel_sq_size(dev, &init_attr->cap, qp_type, qp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx4/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx4/sysfs.c
@@ -223,7 +223,7 @@
 static int add_port_entries(struct mlx4_ib_dev *device, int port_num)
 {
 	int i;
-	char buff[11];
+	char buff[12];
 	struct mlx4_ib_iov_port *port = NULL;
 	int ret = 0 ;
 	struct ib_port_attr attr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/counters.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/counters.c
@@ -249,7 +249,6 @@
 	const struct mlx5_ib_counters *cnts = get_counters(dev, port_num - 1);
 	struct mlx5_core_dev *mdev;
 	int ret, num_counters;
-	u32 mdev_port_num;
 
 	if (!stats)
 		return -EINVAL;
@@ -270,8 +269,9 @@
 	}
 
 	if (MLX5_CAP_GEN(dev->mdev, cc_query_allowed)) {
-		mdev = mlx5_ib_get_native_port_mdev(dev, port_num,
-						    &mdev_port_num);
+		if (!port_num)
+			port_num = 1;
+		mdev = mlx5_ib_get_native_port_mdev(dev, port_num, NULL);
 		if (!mdev) {
 			/* If port is not affiliated yet, its in down state
 			 * which doesn't have any counters yet, so it would be
@@ -337,6 +337,7 @@
 				   struct ib_qp *qp)
 {
 	struct mlx5_ib_dev *dev = to_mdev(qp->device);
+	bool new = false;
 	int err;
 
 	if (!counter->id) {
@@ -351,6 +352,7 @@
 			return err;
 		counter->id =
 			MLX5_GET(alloc_q_counter_out, out, counter_set_id);
+		new = true;
 	}
 
 	err = mlx5_ib_qp_set_counter(qp, counter);
@@ -360,8 +362,10 @@
 	return 0;
 
 fail_set_counter:
-	mlx5_ib_counter_dealloc(counter);
-	counter->id = 0;
+	if (new) {
+		mlx5_ib_counter_dealloc(counter);
+		counter->id = 0;
+	}
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/cq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/cq.c
@@ -481,7 +481,7 @@
 	}
 
 	qpn = ntohl(cqe64->sop_drop_qpn) & 0xffffff;
-	if (!*cur_qp || (qpn != (*cur_qp)->ibqp.qp_num)) {
+	if (!*cur_qp || (qpn != (*cur_qp)->trans_qp.base.mqp.qpn)) {
 		/* We do not have to take the QP table lock here,
 		 * because CQs will be locked while QPs are removed
 		 * from the table.
@@ -735,9 +735,9 @@
 
 	*cqe_size = ucmd.cqe_size;
 
-	cq->buf.umem =
-		ib_umem_get(&dev->ib_dev, ucmd.buf_addr,
-			    entries * ucmd.cqe_size, IB_ACCESS_LOCAL_WRITE);
+	cq->buf.umem = ib_umem_get_peer(&dev->ib_dev, ucmd.buf_addr,
+					entries * ucmd.cqe_size,
+					IB_ACCESS_LOCAL_WRITE, 0);
 	if (IS_ERR(cq->buf.umem)) {
 		err = PTR_ERR(cq->buf.umem);
 		return err;
@@ -1158,9 +1158,9 @@
 	if (ucmd.cqe_size && SIZE_MAX / ucmd.cqe_size <= entries - 1)
 		return -EINVAL;
 
-	umem = ib_umem_get(&dev->ib_dev, ucmd.buf_addr,
-			   (size_t)ucmd.cqe_size * entries,
-			   IB_ACCESS_LOCAL_WRITE);
+	umem = ib_umem_get_peer(&dev->ib_dev, ucmd.buf_addr,
+				(size_t)ucmd.cqe_size * entries,
+				IB_ACCESS_LOCAL_WRITE, 0);
 	if (IS_ERR(umem)) {
 		err = PTR_ERR(umem);
 		return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/devx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/devx.c
@@ -666,7 +666,21 @@
 				      obj_id;
 
 	case MLX5_IB_OBJECT_DEVX_OBJ:
-		return ((struct devx_obj *)uobj->object)->obj_id == obj_id;
+	{
+		u16 opcode = MLX5_GET(general_obj_in_cmd_hdr, in, opcode);
+		struct devx_obj *devx_uobj = uobj->object;
+
+		if (opcode == MLX5_CMD_OP_QUERY_FLOW_COUNTER &&
+		    devx_uobj->flow_counter_bulk_size) {
+			u64 end;
+
+			end = devx_uobj->obj_id +
+				devx_uobj->flow_counter_bulk_size;
+			return devx_uobj->obj_id <= obj_id && end > obj_id;
+		}
+
+		return devx_uobj->obj_id == obj_id;
+	}
 
 	default:
 		return false;
@@ -1303,7 +1317,6 @@
 	mkey->key = mlx5_idx_to_mkey(
 			MLX5_GET(create_mkey_out, out, mkey_index)) | key;
 	mkey->type = MLX5_MKEY_INDIRECT_DEVX;
-	mkey->iova = MLX5_GET64(mkc, mkc, start_addr);
 	mkey->size = MLX5_GET64(mkc, mkc, len);
 	mkey->pd = MLX5_GET(mkc, mkc, pd);
 	devx_mr->ndescs = MLX5_GET(mkc, mkc, translations_octword_size);
@@ -1515,10 +1528,17 @@
 		goto obj_free;
 
 	if (opcode == MLX5_CMD_OP_ALLOC_FLOW_COUNTER) {
-		u8 bulk = MLX5_GET(alloc_flow_counter_in,
-				   cmd_in,
-				   flow_counter_bulk);
-		obj->flow_counter_bulk_size = 128UL * bulk;
+		u32 bulk = MLX5_GET(alloc_flow_counter_in,
+				    cmd_in,
+				    flow_counter_bulk_log_size);
+
+		if (bulk)
+			bulk = 1 << bulk;
+		else
+			bulk = 128UL * MLX5_GET(alloc_flow_counter_in,
+						cmd_in,
+						flow_counter_bulk);
+		obj->flow_counter_bulk_size = bulk;
 	}
 
 	uobj->object = obj;
@@ -1891,8 +1911,10 @@
 				key_level2,
 				obj_event,
 				GFP_KERNEL);
-		if (err)
+		if (err) {
+			kfree(obj_event);
 			return err;
+		}
 		INIT_LIST_HEAD(&obj_event->obj_sub_list);
 	}
 
@@ -2175,7 +2197,7 @@
 	if (err)
 		return err;
 
-	obj->umem = ib_umem_get(&dev->ib_dev, addr, size, access);
+	obj->umem = ib_umem_get_peer(&dev->ib_dev, addr, size, access, 0);
 	if (IS_ERR(obj->umem))
 		return PTR_ERR(obj->umem);
 	return 0;
@@ -2264,6 +2286,8 @@
 		 order_base_2(page_size) - MLX5_ADAPTER_PAGE_SHIFT);
 	MLX5_SET(umem, umem, page_offset,
 		 ib_umem_dma_offset(obj->umem, page_size));
+	if (obj->umem->is_peer)
+		MLX5_SET(umem, umem, ats, MLX5_CAP_GEN(dev->mdev, ats));
 
 	mlx5_ib_populate_pas(obj->umem, page_size, mtt,
 			     (obj->umem->writable ? MLX5_IB_MTT_WRITE : 0) |
@@ -2899,7 +2923,7 @@
 	MLX5_IB_METHOD_DEVX_OBJ_MODIFY,
 	UVERBS_ATTR_IDR(MLX5_IB_ATTR_DEVX_OBJ_MODIFY_HANDLE,
 			UVERBS_IDR_ANY_OBJECT,
-			UVERBS_ACCESS_WRITE,
+			UVERBS_ACCESS_READ,
 			UA_MANDATORY),
 	UVERBS_ATTR_PTR_IN(
 		MLX5_IB_ATTR_DEVX_OBJ_MODIFY_CMD_IN,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/doorbell.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/doorbell.c
@@ -65,8 +65,9 @@
 
 	page->user_virt = (virt & PAGE_MASK);
 	page->refcnt    = 0;
-	page->umem = ib_umem_get(context->ibucontext.device, virt & PAGE_MASK,
-				 PAGE_SIZE, 0);
+	page->umem =
+		ib_umem_get_peer(context->ibucontext.device, virt & PAGE_MASK,
+				 PAGE_SIZE, 0, 0);
 	if (IS_ERR(page->umem)) {
 		err = PTR_ERR(page->umem);
 		kfree(page);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/fs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/fs.c
@@ -2078,12 +2078,10 @@
 		if (err)
 			return err;
 
-		if (flags) {
-			mlx5_ib_ft_type_to_namespace(
+		if (flags)
+			return mlx5_ib_ft_type_to_namespace(
 				MLX5_IB_UAPI_FLOW_TABLE_TYPE_NIC_TX,
 				&obj->ns_type);
-			return 0;
-		}
 	}
 
 	obj->ns_type = MLX5_FLOW_NAMESPACE_BYPASS;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/mad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/mad.c
@@ -166,6 +166,13 @@
 		mdev = dev->mdev;
 		mdev_port_num = 1;
 	}
+	if (MLX5_CAP_GEN(dev->mdev, num_ports) == 1 &&
+	    !mlx5_core_mp_enabled(mdev)) {
+		/* set local port to one for Function-Per-Port HCA. */
+		mdev = dev->mdev;
+		mdev_port_num = 1;
+	}
+
 	/* Declaring support of extended counters */
 	if (in_mad->mad_hdr.attr_id == IB_PMA_CLASS_PORT_INFO) {
 		struct ib_class_port_info cpi = {};
@@ -584,6 +591,11 @@
 			    props->port_cap_flags2 & IB_PORT_LINK_SPEED_HDR_SUP)
 				props->active_speed = IB_SPEED_HDR;
 			break;
+		case 8:
+			if (props->port_cap_flags & IB_PORT_CAP_MASK2_SUP &&
+			    props->port_cap_flags2 & IB_PORT_LINK_SPEED_NDR_SUP)
+				props->active_speed = IB_SPEED_NDR;
+			break;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/main.c
@@ -443,6 +443,10 @@
 		*active_width = IB_WIDTH_2X;
 		*active_speed = IB_SPEED_NDR;
 		break;
+	case MLX5E_PROT_MASK(MLX5E_400GAUI_8):
+		*active_width = IB_WIDTH_8X;
+		*active_speed = IB_SPEED_HDR;
+		break;
 	case MLX5E_PROT_MASK(MLX5E_400GAUI_4_400GBASE_CR4_KR4):
 		*active_width = IB_WIDTH_4X;
 		*active_speed = IB_SPEED_NDR;
@@ -1847,6 +1851,9 @@
 	if (MLX5_CAP_GEN(dev->mdev, drain_sigerr))
 		resp->comp_mask |= MLX5_IB_ALLOC_UCONTEXT_RESP_MASK_SQD2RTS;
 
+	resp->comp_mask |=
+		MLX5_IB_ALLOC_UCONTEXT_RESP_MASK_MKEY_UPDATE_TAG;
+
 	return 0;
 }
 
@@ -2088,7 +2095,7 @@
 	case MLX5_IB_MMAP_DEVICE_MEM:
 		return "Device Memory";
 	default:
-		return NULL;
+		return "Unknown";
 	}
 }
 
@@ -3277,7 +3284,8 @@
 		list_for_each_entry(mpi, &mlx5_ib_unaffiliated_port_list,
 				    list) {
 			if (dev->sys_image_guid == mpi->sys_image_guid &&
-			    (mlx5_core_native_port_num(mpi->mdev) - 1) == i) {
+			    (mlx5_core_native_port_num(mpi->mdev) - 1) == i &&
+			    mlx5_core_same_coredev_type(dev->mdev, mpi->mdev)) {
 				bound = mlx5_ib_bind_slave_port(dev, mpi);
 			}
 
@@ -4369,6 +4377,9 @@
 	STAGE_CREATE(MLX5_IB_STAGE_POST_IB_REG_UMR,
 		     mlx5_ib_stage_post_ib_reg_umr_init,
 		     NULL),
+	STAGE_CREATE(MLX5_IB_STAGE_DELAY_DROP,
+		     mlx5_ib_stage_delay_drop_init,
+		     mlx5_ib_stage_delay_drop_cleanup),
 	STAGE_CREATE(MLX5_IB_STAGE_RESTRACK,
 		     mlx5_ib_restrack_init,
 		     NULL),
@@ -4398,7 +4409,8 @@
 
 	mutex_lock(&mlx5_ib_multiport_mutex);
 	list_for_each_entry(dev, &mlx5_ib_dev_list, ib_dev_list) {
-		if (dev->sys_image_guid == mpi->sys_image_guid)
+		if (dev->sys_image_guid == mpi->sys_image_guid &&
+		    mlx5_core_same_coredev_type(dev->mdev, mpi->mdev))
 			bound = mlx5_ib_bind_slave_port(dev, mpi);
 
 		if (bound) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/mlx5_ib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/mlx5_ib.h
@@ -109,6 +109,19 @@
 		__mlx5_bit_sz(typ, page_offset_fld), 0, scale,                 \
 		page_offset_quantized)
 
+static inline unsigned long
+mlx5_umem_dmabuf_find_best_pgsz(struct ib_umem_dmabuf *umem_dmabuf)
+{
+	/*
+	 * mkeys used for dmabuf are fixed at PAGE_SIZE because we must be able
+	 * to hold any sgl after a move operation. Ideally the mkc page size
+	 * could be changed at runtime to be optimal, but right now the driver
+	 * cannot do that.
+	 */
+	return ib_umem_find_best_pgsz(&umem_dmabuf->umem, PAGE_SIZE,
+				      umem_dmabuf->umem.iova);
+}
+
 enum {
 	MLX5_IB_MMAP_OFFSET_START = 9,
 	MLX5_IB_MMAP_OFFSET_END = 255,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/mr.c
@@ -51,6 +51,7 @@
  */
 void *xlt_emergency_page;
 static DEFINE_MUTEX(xlt_emergency_page_mutex);
+static void mlx5_invalidate_umem(struct ib_umem *umem, void *priv);
 
 enum {
 	MAX_PENDING_REG_MR = 8,
@@ -536,8 +537,10 @@
 		spin_lock_irq(&ent->lock);
 		if (ent->disabled)
 			goto out;
-		if (need_delay)
+		if (need_delay) {
 			queue_delayed_work(cache->wq, &ent->dwork, 300 * HZ);
+			goto out;
+		}
 		remove_cache_mr_locked(ent);
 		queue_adjust_cache_locked(ent);
 	}
@@ -580,6 +583,8 @@
 	ent = &cache->ent[entry];
 	spin_lock_irq(&ent->lock);
 	if (list_empty(&ent->head)) {
+		queue_adjust_cache_locked(ent);
+		ent->miss++;
 		spin_unlock_irq(&ent->lock);
 		mr = create_cache_mr(ent);
 		if (IS_ERR(mr))
@@ -631,6 +636,7 @@
 {
 	struct mlx5_cache_ent *ent = mr->cache_ent;
 
+	WRITE_ONCE(dev->cache.last_add, jiffies);
 	spin_lock_irq(&ent->lock);
 	list_add_tail(&mr->list, &ent->head);
 	ent->available_mrs++;
@@ -911,12 +917,13 @@
 }
 
 static void set_mr_fields(struct mlx5_ib_dev *dev, struct mlx5_ib_mr *mr,
-			  u64 length, int access_flags)
+			  u64 length, int access_flags, u64 iova)
 {
 	mr->ibmr.lkey = mr->mmkey.key;
 	mr->ibmr.rkey = mr->mmkey.key;
 	mr->ibmr.length = length;
 	mr->ibmr.device = &dev->ib_dev;
+	mr->ibmr.iova = iova;
 	mr->access_flags = access_flags;
 }
 
@@ -974,11 +981,10 @@
 
 	mr->ibmr.pd = pd;
 	mr->umem = umem;
-	mr->mmkey.iova = iova;
 	mr->mmkey.size = umem->length;
 	mr->mmkey.pd = to_mpd(pd)->pdn;
 	mr->page_shift = order_base_2(page_size);
-	set_mr_fields(dev, mr, umem->length, access_flags);
+	set_mr_fields(dev, mr, umem->length, access_flags, iova);
 
 	return mr;
 }
@@ -1088,7 +1094,7 @@
 	wr->pd = mr->ibmr.pd;
 	wr->mkey = mr->mmkey.key;
 	wr->length = mr->mmkey.size;
-	wr->virt_addr = mr->mmkey.iova;
+	wr->virt_addr = mr->ibmr.iova;
 	wr->access_flags = mr->access_flags;
 	wr->page_shift = mr->page_shift;
 	wr->xlt_size = sg->length;
@@ -1328,6 +1334,9 @@
 	MLX5_SET(mkc, mkc, translations_octword_size,
 		 get_octo_len(iova, umem->length, mr->page_shift));
 	MLX5_SET(mkc, mkc, log_page_size, mr->page_shift);
+	if (umem->is_peer)
+		MLX5_SET(mkc, mkc, ma_translation_mode,
+			 MLX5_CAP_GEN(dev->mdev, ats));
 	if (populate) {
 		MLX5_SET(create_mkey_in, in, translations_octword_actual_size,
 			 get_octo_len(iova, umem->length, mr->page_shift));
@@ -1340,7 +1349,7 @@
 	}
 	mr->mmkey.type = MLX5_MKEY_MR;
 	mr->umem = umem;
-	set_mr_fields(dev, mr, umem->length, access_flags);
+	set_mr_fields(dev, mr, umem->length, access_flags, iova);
 	kvfree(in);
 
 	mlx5_ib_dbg(dev, "mkey = 0x%x\n", mr->mmkey.key);
@@ -1387,7 +1396,7 @@
 
 	kfree(in);
 
-	set_mr_fields(dev, mr, length, acc);
+	set_mr_fields(dev, mr, length, acc, start_addr);
 
 	return &mr->ibmr;
 
@@ -1457,17 +1466,20 @@
 	int err;
 
 	xlt_with_umr = mlx5_ib_can_load_pas_with_umr(dev, umem->length);
-	if (xlt_with_umr) {
+	if (xlt_with_umr && !umem->is_peer) {
 		mr = alloc_cacheable_mr(pd, umem, iova, access_flags);
 	} else {
 		unsigned int page_size = mlx5_umem_find_best_pgsz(
 			umem, mkc, log_page_size, 0, iova);
 
 		mutex_lock(&dev->slow_path_mutex);
-		mr = reg_create(pd, umem, iova, access_flags, page_size, true);
+		mr = reg_create(pd, umem, iova, access_flags, page_size,
+				!xlt_with_umr);
 		mutex_unlock(&dev->slow_path_mutex);
 	}
 	if (IS_ERR(mr)) {
+		if (umem->is_peer)
+			ib_umem_stop_invalidation_notifier(umem);
 		ib_umem_release(umem);
 		return ERR_CAST(mr);
 	}
@@ -1488,6 +1500,11 @@
 			return ERR_PTR(err);
 		}
 	}
+
+	if (umem->is_peer)
+		ib_umem_activate_invalidation_notifier(
+			umem, mlx5_invalidate_umem, mr);
+
 	return &mr->ibmr;
 }
 
@@ -1565,7 +1582,8 @@
 	if (access_flags & IB_ACCESS_ON_DEMAND)
 		return create_user_odp_mr(pd, start, length, iova, access_flags,
 					  udata);
-	umem = ib_umem_get(&dev->ib_dev, start, length, access_flags);
+	umem = ib_umem_get_peer(&dev->ib_dev, start, length, access_flags,
+				IB_PEER_MEM_INVAL_SUPP);
 	if (IS_ERR(umem))
 		return ERR_CAST(umem);
 	return create_real_mr(pd, umem, iova, access_flags);
@@ -1682,7 +1700,8 @@
 	unsigned int diffs = current_access_flags ^ target_access_flags;
 
 	if (diffs & ~(IB_ACCESS_LOCAL_WRITE | IB_ACCESS_REMOTE_WRITE |
-		      IB_ACCESS_REMOTE_READ | IB_ACCESS_RELAXED_ORDERING))
+		      IB_ACCESS_REMOTE_READ | IB_ACCESS_RELAXED_ORDERING |
+		      IB_ACCESS_REMOTE_ATOMIC))
 		return false;
 	return mlx5_ib_can_reconfig_with_umr(dev, current_access_flags,
 					     target_access_flags);
@@ -1763,7 +1782,7 @@
 	}
 
 	mr->ibmr.length = new_umem->length;
-	mr->mmkey.iova = iova;
+	mr->ibmr.iova = iova;
 	mr->mmkey.size = new_umem->length;
 	mr->page_shift = order_base_2(page_size);
 	mr->umem = new_umem;
@@ -1777,6 +1796,10 @@
 		return err;
 	}
 
+	if (new_umem->is_peer)
+		ib_umem_activate_invalidation_notifier(
+			new_umem, mlx5_invalidate_umem, mr);
+
 	atomic_sub(ib_umem_num_pages(old_umem), &dev->mdev->priv.reg_pages);
 	ib_umem_release(old_umem);
 	atomic_add(ib_umem_num_pages(new_umem), &dev->mdev->priv.reg_pages);
@@ -1819,8 +1842,13 @@
 				return ERR_PTR(err);
 			return NULL;
 		}
-		/* DM or ODP MR's don't have a normal umem so we can't re-use it */
-		if (!mr->umem || is_odp_mr(mr) || is_dmabuf_mr(mr))
+		/*
+		 * DM or ODP MR's don't have a normal umem so we can't re-use it.
+		 * Peer umems cannot have their MR's changed once created due
+		 * to races with invalidation.
+		 */
+		if (!mr->umem || is_odp_mr(mr) || is_dmabuf_mr(mr) ||
+		    mr->umem->is_peer)
 			goto recreate;
 
 		/*
@@ -1834,15 +1862,16 @@
 		mr->umem = NULL;
 		atomic_sub(ib_umem_num_pages(umem), &dev->mdev->priv.reg_pages);
 
-		return create_real_mr(new_pd, umem, mr->mmkey.iova,
+		return create_real_mr(new_pd, umem, mr->ibmr.iova,
 				      new_access_flags);
 	}
 
 	/*
-	 * DM doesn't have a PAS list so we can't re-use it, odp/dmabuf does
-	 * but the logic around releasing the umem is different
+	 * DM doesn't have a PAS list so we can't re-use it, odp/dmabuf does but
+	 * the logic around releasing the umem is different, peer memory
+	 * invalidation semantics are incompatible.
 	 */
-	if (!mr->umem || is_odp_mr(mr) || is_dmabuf_mr(mr))
+	if (!mr->umem || is_odp_mr(mr) || is_dmabuf_mr(mr) || mr->umem->is_peer)
 		goto recreate;
 
 	if (!(new_access_flags & IB_ACCESS_ON_DEMAND) &&
@@ -1850,8 +1879,9 @@
 		struct ib_umem *new_umem;
 		unsigned long page_size;
 
-		new_umem = ib_umem_get(&dev->ib_dev, start, length,
-				       new_access_flags);
+		new_umem = ib_umem_get_peer(&dev->ib_dev, start, length,
+					    new_access_flags,
+					    IB_PEER_MEM_INVAL_SUPP);
 		if (IS_ERR(new_umem))
 			return ERR_CAST(new_umem);
 
@@ -1971,14 +2001,23 @@
 	}
 
 	/* Stop DMA */
-	if (mr->cache_ent) {
-		if (revoke_mr(mr)) {
-			spin_lock_irq(&mr->cache_ent->lock);
-			mr->cache_ent->total_mrs--;
-			spin_unlock_irq(&mr->cache_ent->lock);
-			mr->cache_ent = NULL;
+	rc = 0;
+	if (mr->cache_ent || (mr->umem && mr->umem->is_peer)) {
+		rc = revoke_mr(mr);
+		if (mr->umem && mr->umem->is_peer) {
+			if (rc)
+				return rc;
+			ib_umem_stop_invalidation_notifier(mr->umem);
 		}
 	}
+
+	if (mr->cache_ent && rc) {
+		spin_lock_irq(&mr->cache_ent->lock);
+		mr->cache_ent->total_mrs--;
+		spin_unlock_irq(&mr->cache_ent->lock);
+		mr->cache_ent = NULL;
+	}
+
 	if (!mr->cache_ent) {
 		rc = destroy_mkey(to_mdev(mr->ibmr.device), mr);
 		if (rc)
@@ -2701,3 +2740,15 @@
 
 	return n;
 }
+
+static void mlx5_invalidate_umem(struct ib_umem *umem, void *priv)
+{
+	struct mlx5_ib_mr *mr = priv;
+
+	/*
+	 * DMA is turned off for the mkey, but the mkey remains otherwise
+	 * untouched until the normal flow of dereg_mr happens. Any access to
+	 * this mkey will generate CQEs.
+	 */
+	revoke_mr(mr);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/odp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/odp.c
@@ -430,7 +430,7 @@
 	mr->umem = &odp->umem;
 	mr->ibmr.lkey = mr->mmkey.key;
 	mr->ibmr.rkey = mr->mmkey.key;
-	mr->mmkey.iova = idx * MLX5_IMR_MTT_SIZE;
+	mr->ibmr.iova = idx * MLX5_IMR_MTT_SIZE;
 	mr->parent = imr;
 	odp->private = mr;
 
@@ -500,7 +500,7 @@
 	}
 
 	imr->ibmr.pd = &pd->ibpd;
-	imr->mmkey.iova = 0;
+	imr->ibmr.iova = 0;
 	imr->umem = &umem_odp->umem;
 	imr->ibmr.lkey = imr->mmkey.key;
 	imr->ibmr.rkey = imr->mmkey.key;
@@ -704,10 +704,8 @@
 		return err;
 	}
 
-	page_size = mlx5_umem_find_best_pgsz(&umem_dmabuf->umem, mkc,
-					     log_page_size, 0,
-					     umem_dmabuf->umem.iova);
-	if (unlikely(page_size < PAGE_SIZE)) {
+	page_size = mlx5_umem_dmabuf_find_best_pgsz(umem_dmabuf);
+	if (!page_size) {
 		ib_umem_dmabuf_unmap_pages(umem_dmabuf);
 		err = -EINVAL;
 	} else {
@@ -734,24 +732,31 @@
  *  >0: Number of pages mapped
  */
 static int pagefault_mr(struct mlx5_ib_mr *mr, u64 io_virt, size_t bcnt,
-			u32 *bytes_mapped, u32 flags)
+			u32 *bytes_mapped, u32 flags, bool permissive_fault)
 {
 	struct ib_umem_odp *odp = to_ib_umem_odp(mr->umem);
 
-	if (unlikely(io_virt < mr->mmkey.iova))
+	if (unlikely(io_virt < mr->ibmr.iova) && !permissive_fault)
 		return -EFAULT;
 
 	if (mr->umem->is_dmabuf)
 		return pagefault_dmabuf_mr(mr, bcnt, bytes_mapped, flags);
 
 	if (!odp->is_implicit_odp) {
+		u64 offset = io_virt < mr->ibmr.iova ? 0 : io_virt - mr->ibmr.iova;
 		u64 user_va;
 
-		if (check_add_overflow(io_virt - mr->mmkey.iova,
-				       (u64)odp->umem.address, &user_va))
+		if (check_add_overflow(offset, (u64)odp->umem.address,
+				       &user_va))
 			return -EFAULT;
-		if (unlikely(user_va >= ib_umem_end(odp) ||
-			     ib_umem_end(odp) - user_va < bcnt))
+
+		if (permissive_fault) {
+			if (user_va < ib_umem_start(odp))
+				user_va = ib_umem_start(odp);
+			if ((user_va + bcnt) > ib_umem_end(odp))
+				bcnt = ib_umem_end(odp) - user_va;
+		} else if (unlikely(user_va >= ib_umem_end(odp) ||
+				    ib_umem_end(odp) - user_va < bcnt))
 			return -EFAULT;
 		return pagefault_real_mr(mr, odp, user_va, bcnt, bytes_mapped,
 					 flags);
@@ -792,7 +797,8 @@
 {
 	if (!mmkey)
 		return false;
-	if (mmkey->type == MLX5_MKEY_MW)
+	if (mmkey->type == MLX5_MKEY_MW ||
+	    mmkey->type == MLX5_MKEY_INDIRECT_DEVX)
 		return mlx5_base_mkey(mmkey->key) == mlx5_base_mkey(key);
 	return mmkey->key == key;
 }
@@ -815,8 +821,7 @@
 /*
  * Handle a single data segment in a page-fault WQE or RDMA region.
  *
- * Returns number of OS pages retrieved on success. The caller may continue to
- * the next data segment.
+ * Returns zero on success. The caller may continue to the next data segment.
  * Can return the following error codes:
  * -EAGAIN to designate a temporary error. The caller will abort handling the
  *  page fault and resolve it.
@@ -829,7 +834,7 @@
 					 u32 *bytes_committed,
 					 u32 *bytes_mapped)
 {
-	int npages = 0, ret, i, outlen, cur_outlen = 0, depth = 0;
+	int ret, i, outlen, cur_outlen = 0, depth = 0, pages_in_range;
 	struct pf_frame *head = NULL, *frame;
 	struct mlx5_core_mkey *mmkey;
 	struct mlx5_ib_mr *mr;
@@ -873,13 +878,20 @@
 	case MLX5_MKEY_MR:
 		mr = container_of(mmkey, struct mlx5_ib_mr, mmkey);
 
-		ret = pagefault_mr(mr, io_virt, bcnt, bytes_mapped, 0);
+		pages_in_range = (ALIGN(io_virt + bcnt, PAGE_SIZE) -
+				  (io_virt & PAGE_MASK)) >>
+				 PAGE_SHIFT;
+		ret = pagefault_mr(mr, io_virt, bcnt, bytes_mapped, 0, false);
 		if (ret < 0)
 			goto end;
 
 		mlx5_update_odp_stats(mr, faults, ret);
 
-		npages += ret;
+		if (ret < pages_in_range) {
+			ret = -EFAULT;
+			goto end;
+		}
+
 		ret = 0;
 		break;
 
@@ -972,7 +984,7 @@
 	kfree(out);
 
 	*bytes_committed = 0;
-	return ret ? ret : npages;
+	return ret;
 }
 
 /*
@@ -991,8 +1003,7 @@
  *                   the committed bytes).
  * @receive_queue: receive WQE end of sg list
  *
- * Returns the number of pages loaded if positive, zero for an empty WQE, or a
- * negative error code.
+ * Returns zero for success or a negative error code.
  */
 static int pagefault_data_segments(struct mlx5_ib_dev *dev,
 				   struct mlx5_pagefault *pfault,
@@ -1000,7 +1011,7 @@
 				   void *wqe_end, u32 *bytes_mapped,
 				   u32 *total_wqe_bytes, bool receive_queue)
 {
-	int ret = 0, npages = 0;
+	int ret = 0;
 	u64 io_virt;
 	u32 key;
 	u32 byte_count;
@@ -1056,10 +1067,9 @@
 						    bytes_mapped);
 		if (ret < 0)
 			break;
-		npages += ret;
 	}
 
-	return ret < 0 ? ret : npages;
+	return ret;
 }
 
 /*
@@ -1295,12 +1305,6 @@
 	free_page((unsigned long)wqe_start);
 }
 
-static int pages_in_range(u64 address, u32 length)
-{
-	return (ALIGN(address + length, PAGE_SIZE) -
-		(address & PAGE_MASK)) >> PAGE_SHIFT;
-}
-
 static void mlx5_ib_mr_rdma_pfault_handler(struct mlx5_ib_dev *dev,
 					   struct mlx5_pagefault *pfault)
 {
@@ -1339,7 +1343,7 @@
 	if (ret == -EAGAIN) {
 		/* We're racing with an invalidation, don't prefetch */
 		prefetch_activated = 0;
-	} else if (ret < 0 || pages_in_range(address, length) > ret) {
+	} else if (ret < 0) {
 		mlx5_ib_page_fault_resume(dev, pfault, 1);
 		if (ret != -ENOENT)
 			mlx5_ib_dbg(dev, "PAGE FAULT error %d. QP 0x%x, type: 0x%x\n",
@@ -1744,7 +1748,7 @@
 	for (i = 0; i < work->num_sge; ++i) {
 		ret = pagefault_mr(work->frags[i].mr, work->frags[i].io_virt,
 				   work->frags[i].length, &bytes_mapped,
-				   work->pf_flags);
+				   work->pf_flags, false);
 		if (ret <= 0)
 			continue;
 		mlx5_update_odp_stats(work->frags[i].mr, prefetch, ret);
@@ -1793,7 +1797,7 @@
 		if (!mr)
 			return -ENOENT;
 		ret = pagefault_mr(mr, sg_list[i].addr, sg_list[i].length,
-				   &bytes_mapped, pf_flags);
+				   &bytes_mapped, pf_flags, false);
 		if (ret < 0) {
 			mlx5r_deref_odp_mkey(&mr->mmkey);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/qp.c
@@ -807,7 +807,7 @@
 	if (!ucmd->buf_addr)
 		return -EINVAL;
 
-	rwq->umem = ib_umem_get(&dev->ib_dev, ucmd->buf_addr, rwq->buf_size, 0);
+	rwq->umem = ib_umem_get_peer(&dev->ib_dev, ucmd->buf_addr, rwq->buf_size, 0, 0);
 	if (IS_ERR(rwq->umem)) {
 		mlx5_ib_dbg(dev, "umem_get failed\n");
 		err = PTR_ERR(rwq->umem);
@@ -917,8 +917,9 @@
 
 	if (ucmd->buf_addr && ubuffer->buf_size) {
 		ubuffer->buf_addr = ucmd->buf_addr;
-		ubuffer->umem = ib_umem_get(&dev->ib_dev, ubuffer->buf_addr,
-					    ubuffer->buf_size, 0);
+		ubuffer->umem =
+			ib_umem_get_peer(&dev->ib_dev, ubuffer->buf_addr,
+					 ubuffer->buf_size, 0, 0);
 		if (IS_ERR(ubuffer->umem)) {
 			err = PTR_ERR(ubuffer->umem);
 			goto err_bfreg;
@@ -1269,8 +1270,8 @@
 	if (ts_format < 0)
 		return ts_format;
 
-	sq->ubuffer.umem = ib_umem_get(&dev->ib_dev, ubuffer->buf_addr,
-				       ubuffer->buf_size, 0);
+	sq->ubuffer.umem = ib_umem_get_peer(&dev->ib_dev, ubuffer->buf_addr,
+				       ubuffer->buf_size, 0, 0);
 	if (IS_ERR(sq->ubuffer.umem))
 		return PTR_ERR(sq->ubuffer.umem);
 	page_size = mlx5_umem_find_best_quantized_pgoff(
@@ -3955,6 +3956,30 @@
 	return tx_affinity;
 }
 
+static int __mlx5_ib_qp_set_raw_qp_counter(struct mlx5_ib_qp *qp, u32 set_id,
+					   struct mlx5_core_dev *mdev)
+{
+	struct mlx5_ib_raw_packet_qp *raw_packet_qp = &qp->raw_packet_qp;
+	struct mlx5_ib_rq *rq = &raw_packet_qp->rq;
+	u32 in[MLX5_ST_SZ_DW(modify_rq_in)] = {};
+	void *rqc;
+
+	if (!qp->rq.wqe_cnt)
+		return 0;
+
+	MLX5_SET(modify_rq_in, in, rq_state, rq->state);
+	MLX5_SET(modify_rq_in, in, uid, to_mpd(qp->ibqp.pd)->uid);
+
+	rqc = MLX5_ADDR_OF(modify_rq_in, in, ctx);
+	MLX5_SET(rqc, rqc, state, MLX5_RQC_STATE_RDY);
+
+	MLX5_SET64(modify_rq_in, in, modify_bitmask,
+		   MLX5_MODIFY_RQ_IN_MODIFY_BITMASK_RQ_COUNTER_SET_ID);
+	MLX5_SET(rqc, rqc, counter_set_id, set_id);
+
+	return mlx5_core_modify_rq(mdev, rq->base.mqp.qpn, in);
+}
+
 static int __mlx5_ib_qp_set_counter(struct ib_qp *qp,
 				    struct rdma_counter *counter)
 {
@@ -3970,6 +3995,9 @@
 	else
 		set_id = mlx5_ib_get_counters_id(dev, mqp->port - 1);
 
+	if (mqp->type == IB_QPT_RAW_PACKET)
+		return __mlx5_ib_qp_set_raw_qp_counter(mqp, set_id, dev->mdev);
+
 	base = &mqp->trans_qp.base;
 	MLX5_SET(rts2rts_qp_in, in, opcode, MLX5_CMD_OP_RTS2RTS_QP);
 	MLX5_SET(rts2rts_qp_in, in, qpn, base->mqp.qpn);
@@ -4155,14 +4183,14 @@
 		MLX5_SET(qpc, qpc, retry_count, attr->retry_cnt);
 
 	if (attr_mask & IB_QP_MAX_QP_RD_ATOMIC && attr->max_rd_atomic)
-		MLX5_SET(qpc, qpc, log_sra_max, ilog2(attr->max_rd_atomic));
+		MLX5_SET(qpc, qpc, log_sra_max, fls(attr->max_rd_atomic - 1));
 
 	if (attr_mask & IB_QP_SQ_PSN)
 		MLX5_SET(qpc, qpc, next_send_psn, attr->sq_psn);
 
 	if (attr_mask & IB_QP_MAX_DEST_RD_ATOMIC && attr->max_dest_rd_atomic)
 		MLX5_SET(qpc, qpc, log_rra_max,
-			 ilog2(attr->max_dest_rd_atomic));
+			 fls(attr->max_dest_rd_atomic - 1));
 
 	if (attr_mask & (IB_QP_ACCESS_FLAGS | IB_QP_MAX_DEST_RD_ATOMIC)) {
 		err = set_qpc_atomic_flags(qp, attr, attr_mask, qpc);
@@ -4406,7 +4434,7 @@
 			return -EINVAL;
 
 		if (attr->port_num == 0 ||
-		    attr->port_num > MLX5_CAP_GEN(dev->mdev, num_ports)) {
+		    attr->port_num > dev->num_ports) {
 			mlx5_ib_dbg(dev, "invalid port number %d. number of ports is %d\n",
 				    attr->port_num, dev->num_ports);
 			return -EINVAL;
@@ -4434,6 +4462,8 @@
 
 		set_id = mlx5_ib_get_counters_id(dev, attr->port_num - 1);
 		MLX5_SET(dctc, dctc, counter_set_id, set_id);
+
+		qp->port = attr->port_num;
 	} else if (cur_state == IB_QPS_INIT && new_state == IB_QPS_RTR) {
 		struct mlx5_ib_modify_qp_resp resp = {};
 		u32 out[MLX5_ST_SZ_DW(create_dct_out)] = {};
@@ -4499,6 +4529,40 @@
 	return false;
 }
 
+static int validate_rd_atomic(struct mlx5_ib_dev *dev, struct ib_qp_attr *attr,
+			      int attr_mask, enum ib_qp_type qp_type)
+{
+	int log_max_ra_res;
+	int log_max_ra_req;
+
+	if (qp_type == MLX5_IB_QPT_DCI) {
+		log_max_ra_res = 1 << MLX5_CAP_GEN(dev->mdev,
+						   log_max_ra_res_dc);
+		log_max_ra_req = 1 << MLX5_CAP_GEN(dev->mdev,
+						   log_max_ra_req_dc);
+	} else {
+		log_max_ra_res = 1 << MLX5_CAP_GEN(dev->mdev,
+						   log_max_ra_res_qp);
+		log_max_ra_req = 1 << MLX5_CAP_GEN(dev->mdev,
+						   log_max_ra_req_qp);
+	}
+
+	if (attr_mask & IB_QP_MAX_QP_RD_ATOMIC &&
+	    attr->max_rd_atomic > log_max_ra_res) {
+		mlx5_ib_dbg(dev, "invalid max_rd_atomic value %d\n",
+			    attr->max_rd_atomic);
+		return false;
+	}
+
+	if (attr_mask & IB_QP_MAX_DEST_RD_ATOMIC &&
+	    attr->max_dest_rd_atomic > log_max_ra_req) {
+		mlx5_ib_dbg(dev, "invalid max_dest_rd_atomic value %d\n",
+			    attr->max_dest_rd_atomic);
+		return false;
+	}
+	return true;
+}
+
 int mlx5_ib_modify_qp(struct ib_qp *ibqp, struct ib_qp_attr *attr,
 		      int attr_mask, struct ib_udata *udata)
 {
@@ -4586,21 +4650,8 @@
 		goto out;
 	}
 
-	if (attr_mask & IB_QP_MAX_QP_RD_ATOMIC &&
-	    attr->max_rd_atomic >
-	    (1 << MLX5_CAP_GEN(dev->mdev, log_max_ra_res_qp))) {
-		mlx5_ib_dbg(dev, "invalid max_rd_atomic value %d\n",
-			    attr->max_rd_atomic);
+	if (!validate_rd_atomic(dev, attr, attr_mask, qp_type))
 		goto out;
-	}
-
-	if (attr_mask & IB_QP_MAX_DEST_RD_ATOMIC &&
-	    attr->max_dest_rd_atomic >
-	    (1 << MLX5_CAP_GEN(dev->mdev, log_max_ra_req_qp))) {
-		mlx5_ib_dbg(dev, "invalid max_dest_rd_atomic value %d\n",
-			    attr->max_dest_rd_atomic);
-		goto out;
-	}
 
 	if (cur_state == new_state && cur_state == IB_QPS_RESET) {
 		err = 0;
@@ -4901,7 +4952,7 @@
 	}
 
 	if (qp_attr_mask & IB_QP_PORT)
-		qp_attr->port_num = MLX5_GET(dctc, dctc, port);
+		qp_attr->port_num = mqp->port;
 	if (qp_attr_mask & IB_QP_MIN_RNR_TIMER)
 		qp_attr->min_rnr_timer = MLX5_GET(dctc, dctc, min_rnr_nak);
 	if (qp_attr_mask & IB_QP_AV) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/qpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/qpc.c
@@ -297,8 +297,7 @@
 	MLX5_SET(destroy_qp_in, in, opcode, MLX5_CMD_OP_DESTROY_QP);
 	MLX5_SET(destroy_qp_in, in, qpn, qp->qpn);
 	MLX5_SET(destroy_qp_in, in, uid, qp->uid);
-	mlx5_cmd_exec_in(dev->mdev, destroy_qp, in);
-	return 0;
+	return mlx5_cmd_exec_in(dev->mdev, destroy_qp, in);
 }
 
 int mlx5_core_set_delay_drop(struct mlx5_ib_dev *dev,
@@ -548,14 +547,14 @@
 	return mlx5_cmd_exec_in(dev->mdev, dealloc_xrcd, in);
 }
 
-static void destroy_rq_tracked(struct mlx5_ib_dev *dev, u32 rqn, u16 uid)
+static int destroy_rq_tracked(struct mlx5_ib_dev *dev, u32 rqn, u16 uid)
 {
 	u32 in[MLX5_ST_SZ_DW(destroy_rq_in)] = {};
 
 	MLX5_SET(destroy_rq_in, in, opcode, MLX5_CMD_OP_DESTROY_RQ);
 	MLX5_SET(destroy_rq_in, in, rqn, rqn);
 	MLX5_SET(destroy_rq_in, in, uid, uid);
-	mlx5_cmd_exec_in(dev->mdev, destroy_rq, in);
+	return mlx5_cmd_exec_in(dev->mdev, destroy_rq, in);
 }
 
 int mlx5_core_create_rq_tracked(struct mlx5_ib_dev *dev, u32 *in, int inlen,
@@ -586,8 +585,7 @@
 				 struct mlx5_core_qp *rq)
 {
 	destroy_resource_common(dev, rq);
-	destroy_rq_tracked(dev, rq->qpn, rq->uid);
-	return 0;
+	return destroy_rq_tracked(dev, rq->qpn, rq->uid);
 }
 
 static void destroy_sq_tracked(struct mlx5_ib_dev *dev, u32 sqn, u16 uid)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/srq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/srq.c
@@ -76,7 +76,7 @@
 
 	srq->wq_sig = !!(ucmd.flags & MLX5_SRQ_FLAG_SIGNATURE);
 
-	srq->umem = ib_umem_get(pd->device, ucmd.buf_addr, buf_size, 0);
+	srq->umem = ib_umem_get_peer(pd->device, ucmd.buf_addr, buf_size, 0, 0);
 	if (IS_ERR(srq->umem)) {
 		mlx5_ib_dbg(dev, "failed umem get, size %d\n", buf_size);
 		err = PTR_ERR(srq->umem);
@@ -200,17 +200,20 @@
 	int err;
 	struct mlx5_srq_attr in = {};
 	__u32 max_srq_wqes = 1 << MLX5_CAP_GEN(dev->mdev, log_max_srq_sz);
+	__u32 max_sge_sz =  MLX5_CAP_GEN(dev->mdev, max_wqe_sz_rq) /
+			    sizeof(struct mlx5_wqe_data_seg);
 
 	if (init_attr->srq_type != IB_SRQT_BASIC &&
 	    init_attr->srq_type != IB_SRQT_XRC &&
 	    init_attr->srq_type != IB_SRQT_TM)
 		return -EOPNOTSUPP;
 
-	/* Sanity check SRQ size before proceeding */
-	if (init_attr->attr.max_wr >= max_srq_wqes) {
-		mlx5_ib_dbg(dev, "max_wr %d, cap %d\n",
-			    init_attr->attr.max_wr,
-			    max_srq_wqes);
+	/* Sanity check SRQ and sge size before proceeding */
+	if (init_attr->attr.max_wr >= max_srq_wqes ||
+	    init_attr->attr.max_sge > max_sge_sz) {
+		mlx5_ib_dbg(dev, "max_wr %d,wr_cap %d,max_sge %d, sge_cap:%d\n",
+			    init_attr->attr.max_wr, max_srq_wqes,
+			    init_attr->attr.max_sge, max_sge_sz);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mlx5/wr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mlx5/wr.c
@@ -128,7 +128,7 @@
 		 */
 		copysz = min_t(u64, *cur_edge - (void *)eseg->inline_hdr.start,
 			       left);
-		memcpy(eseg->inline_hdr.start, pdata, copysz);
+		memcpy(eseg->inline_hdr.data, pdata, copysz);
 		stride = ALIGN(sizeof(struct mlx5_wqe_eth_seg) -
 			       sizeof(eseg->inline_hdr.start) + copysz, 16);
 		*size += stride / 16;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mthca/mthca_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mthca/mthca_cmd.c
@@ -635,7 +635,7 @@
 
 int mthca_SYS_EN(struct mthca_dev *dev)
 {
-	u64 out;
+	u64 out = 0;
 	int ret;
 
 	ret = mthca_cmd_imm(dev, 0, &out, 0, 0, CMD_SYS_EN, CMD_TIME_CLASS_D);
@@ -1955,7 +1955,7 @@
 int mthca_MGID_HASH(struct mthca_dev *dev, struct mthca_mailbox *mailbox,
 		    u16 *hash)
 {
-	u64 imm;
+	u64 imm = 0;
 	int err;
 
 	err = mthca_cmd_imm(dev, mailbox->dma, &imm, 0, 0, CMD_MGID_HASH,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mthca/mthca_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mthca/mthca_main.c
@@ -382,7 +382,7 @@
 			  struct mthca_init_hca_param *init_hca,
 			  u64 icm_size)
 {
-	u64 aux_pages;
+	u64 aux_pages = 0;
 	int err;
 
 	err = mthca_SET_ICM_SIZE(mdev, icm_size, &aux_pages);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/mthca/mthca_qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/mthca/mthca_qp.c
@@ -1393,7 +1393,7 @@
 	if (mthca_array_get(&dev->qp_table.qp, mqpn))
 		err = -EBUSY;
 	else
-		mthca_array_set(&dev->qp_table.qp, mqpn, qp->sqp);
+		mthca_array_set(&dev->qp_table.qp, mqpn, qp);
 	spin_unlock_irq(&dev->qp_table.lock);
 
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/qedr/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/qedr/main.c
@@ -345,6 +345,10 @@
 	if (IS_IWARP(dev)) {
 		xa_init(&dev->qps);
 		dev->iwarp_wq = create_singlethread_workqueue("qedr_iwarpq");
+		if (!dev->iwarp_wq) {
+			rc = -ENOMEM;
+			goto err1;
+		}
 	}
 
 	/* Allocate Status blocks for CNQ */
@@ -352,7 +356,7 @@
 				GFP_KERNEL);
 	if (!dev->sb_array) {
 		rc = -ENOMEM;
-		goto err1;
+		goto err_destroy_wq;
 	}
 
 	dev->cnq_array = kcalloc(dev->num_cnq,
@@ -403,6 +407,9 @@
 	kfree(dev->cnq_array);
 err2:
 	kfree(dev->sb_array);
+err_destroy_wq:
+	if (IS_IWARP(dev))
+		destroy_workqueue(dev->iwarp_wq);
 err1:
 	kfree(dev->sgid_tbl);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/qedr/qedr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/qedr/qedr.h
@@ -418,6 +418,7 @@
 	u32 sq_psn;
 	u32 qkey;
 	u32 dest_qp_num;
+	u8 timeout;
 
 	/* Relevant to qps created from kernel space only (ULPs) */
 	u8 prev_wqe_size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/qedr/verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/qedr/verbs.c
@@ -1888,8 +1888,17 @@
 		/* RQ - read access only (0) */
 		rc = qedr_init_user_queue(udata, dev, &qp->urq, ureq.rq_addr,
 					  ureq.rq_len, true, 0, alloc_and_init);
-		if (rc)
+		if (rc) {
+			ib_umem_release(qp->usq.umem);
+			qp->usq.umem = NULL;
+			if (rdma_protocol_roce(&dev->ibdev, 1)) {
+				qedr_free_pbl(dev, &qp->usq.pbl_info,
+					      qp->usq.pbl_tbl);
+			} else {
+				kfree(qp->usq.pbl_tbl);
+			}
 			return rc;
+		}
 	}
 
 	memset(&in_params, 0, sizeof(in_params));
@@ -1941,6 +1950,7 @@
 	/* db offset was calculated in copy_qp_uresp, now set in the user q */
 	if (qedr_qp_has_sq(qp)) {
 		qp->usq.db_addr = ctx->dpi_addr + uresp.sq_db_offset;
+		qp->sq.max_wr = attrs->cap.max_send_wr;
 		rc = qedr_db_recovery_add(dev, qp->usq.db_addr,
 					  &qp->usq.db_rec_data->db_data,
 					  DB_REC_WIDTH_32B,
@@ -1951,6 +1961,7 @@
 
 	if (qedr_qp_has_rq(qp)) {
 		qp->urq.db_addr = ctx->dpi_addr + uresp.rq_db_offset;
+		qp->rq.max_wr = attrs->cap.max_recv_wr;
 		rc = qedr_db_recovery_add(dev, qp->urq.db_addr,
 					  &qp->urq.db_rec_data->db_data,
 					  DB_REC_WIDTH_32B,
@@ -2620,6 +2631,8 @@
 					1 << max_t(int, attr->timeout - 8, 0);
 		else
 			qp_params.ack_timeout = 0;
+
+		qp->timeout = attr->timeout;
 	}
 
 	if (attr_mask & IB_QP_RETRY_CNT) {
@@ -2744,15 +2757,18 @@
 	int rc = 0;
 
 	memset(&params, 0, sizeof(params));
-
-	rc = dev->ops->rdma_query_qp(dev->rdma_ctx, qp->qed_qp, &params);
-	if (rc)
-		goto err;
-
 	memset(qp_attr, 0, sizeof(*qp_attr));
 	memset(qp_init_attr, 0, sizeof(*qp_init_attr));
 
-	qp_attr->qp_state = qedr_get_ibqp_state(params.state);
+	if (qp->qp_type != IB_QPT_GSI) {
+		rc = dev->ops->rdma_query_qp(dev->rdma_ctx, qp->qed_qp, &params);
+		if (rc)
+			goto err;
+		qp_attr->qp_state = qedr_get_ibqp_state(params.state);
+	} else {
+		qp_attr->qp_state = qedr_get_ibqp_state(QED_ROCE_QP_STATE_RTS);
+	}
+
 	qp_attr->cur_qp_state = qedr_get_ibqp_state(params.state);
 	qp_attr->path_mtu = ib_mtu_int_to_enum(params.mtu);
 	qp_attr->path_mig_state = IB_MIG_MIGRATED;
@@ -2776,7 +2792,7 @@
 	rdma_ah_set_dgid_raw(&qp_attr->ah_attr, &params.dgid.bytes[0]);
 	rdma_ah_set_port_num(&qp_attr->ah_attr, 1);
 	rdma_ah_set_sl(&qp_attr->ah_attr, 0);
-	qp_attr->timeout = params.timeout;
+	qp_attr->timeout = qp->timeout;
 	qp_attr->rnr_retry = params.rnr_retry;
 	qp_attr->retry_cnt = params.retry_cnt;
 	qp_attr->min_rnr_timer = params.min_rnr_nak_timer;
@@ -3086,7 +3102,7 @@
 		else
 			DP_ERR(dev, "roce alloc tid returned error %d\n", rc);
 
-		goto err0;
+		goto err1;
 	}
 
 	/* Index only, 18 bit long, lkey = itid << 8 | key */
@@ -3110,7 +3126,7 @@
 	rc = dev->ops->rdma_register_tid(dev->rdma_ctx, &mr->hw_mr);
 	if (rc) {
 		DP_ERR(dev, "roce register tid returned an error %d\n", rc);
-		goto err1;
+		goto err2;
 	}
 
 	mr->ibmr.lkey = mr->hw_mr.itid << 8 | mr->hw_mr.key;
@@ -3119,8 +3135,10 @@
 	DP_DEBUG(dev, QEDR_MSG_MR, "alloc frmr: %x\n", mr->ibmr.lkey);
 	return mr;
 
-err1:
+err2:
 	dev->ops->rdma_free_tid(dev->rdma_ctx, mr->hw_mr.itid);
+err1:
+	qedr_free_pbl(dev, &mr->info.pbl_info, mr->info.pbl_table);
 err0:
 	kfree(mr);
 	return ERR_PTR(rc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/qib/qib_fs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/qib/qib_fs.c
@@ -441,6 +441,7 @@
 		return PTR_ERR(dir);
 	}
 	simple_recursive_removal(dir, NULL);
+	dput(dir);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/qib/qib_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/qib/qib_sysfs.c
@@ -541,7 +541,7 @@
 };
 
 static const struct attribute_group port_diagc_group = {
-	.name = "linkcontrol",
+	.name = "diag_counters",
 	.attrs = port_diagc_attributes,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/qib/qib_user_sdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/qib/qib_user_sdma.c
@@ -941,7 +941,7 @@
 					       &addrlimit) ||
 			    addrlimit > type_max(typeof(pkt->addrlimit))) {
 				ret = -EINVAL;
-				goto free_pbc;
+				goto free_pkt;
 			}
 			pkt->addrlimit = addrlimit;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/hw/usnic/usnic_uiom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/hw/usnic/usnic_uiom.c
@@ -281,8 +281,8 @@
 				size = pa_end - pa_start + PAGE_SIZE;
 				usnic_dbg("va 0x%lx pa %pa size 0x%zx flags 0x%x",
 					va_start, &pa_start, size, flags);
-				err = iommu_map(pd->domain, va_start, pa_start,
-							size, flags);
+				err = iommu_map_atomic(pd->domain, va_start,
+						       pa_start, size, flags);
 				if (err) {
 					usnic_err("Failed to map va 0x%lx pa %pa size 0x%zx with err %d\n",
 						va_start, &pa_start, size, err);
@@ -298,8 +298,8 @@
 				size = pa - pa_start + PAGE_SIZE;
 				usnic_dbg("va 0x%lx pa %pa size 0x%zx flags 0x%x\n",
 					va_start, &pa_start, size, flags);
-				err = iommu_map(pd->domain, va_start, pa_start,
-						size, flags);
+				err = iommu_map_atomic(pd->domain, va_start,
+						       pa_start, size, flags);
 				if (err) {
 					usnic_err("Failed to map va 0x%lx pa %pa size 0x%zx with err %d\n",
 						va_start, &pa_start, size, err);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rdmavt/qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rdmavt/qp.c
@@ -464,8 +464,6 @@
 	if (qps_inuse)
 		rvt_pr_err(rdi, "QP memory leak! %u still in use\n",
 			   qps_inuse);
-	if (!rdi->qp_dev)
-		return;
 
 	kfree(rdi->qp_dev->qp_table);
 	free_qpn_table(&rdi->qp_dev->qpn_table);
@@ -2775,7 +2773,7 @@
 EXPORT_SYMBOL(rvt_qp_iter);
 
 /*
- * This should be called with s_lock held.
+ * This should be called with s_lock and r_lock held.
  */
 void rvt_send_complete(struct rvt_qp *qp, struct rvt_swqe *wqe,
 		       enum ib_wc_status status)
@@ -3073,6 +3071,8 @@
 	case IB_WR_ATOMIC_FETCH_AND_ADD:
 		if (unlikely(!(qp->qp_access_flags & IB_ACCESS_REMOTE_ATOMIC)))
 			goto inv_err;
+		if (unlikely(wqe->atomic_wr.remote_addr & (sizeof(u64) - 1)))
+			goto inv_err;
 		if (unlikely(!rvt_rkey_ok(qp, &qp->r_sge.sge, sizeof(u64),
 					  wqe->atomic_wr.remote_addr,
 					  wqe->atomic_wr.rkey,
@@ -3132,7 +3132,9 @@
 	rvp->n_loop_pkts++;
 flush_send:
 	sqp->s_rnr_retry = sqp->s_rnr_retry_cnt;
+	spin_lock(&sqp->r_lock);
 	rvt_send_complete(sqp, wqe, send_status);
+	spin_unlock(&sqp->r_lock);
 	if (local_ops) {
 		atomic_dec(&sqp->local_ops_pending);
 		local_ops = 0;
@@ -3186,9 +3188,15 @@
 	spin_unlock_irqrestore(&qp->r_lock, flags);
 serr_no_r_lock:
 	spin_lock_irqsave(&sqp->s_lock, flags);
+	spin_lock(&sqp->r_lock);
 	rvt_send_complete(sqp, wqe, send_status);
+	spin_unlock(&sqp->r_lock);
 	if (sqp->ibqp.qp_type == IB_QPT_RC) {
-		int lastwqe = rvt_error_qp(sqp, IB_WC_WR_FLUSH_ERR);
+		int lastwqe;
+
+		spin_lock(&sqp->r_lock);
+		lastwqe = rvt_error_qp(sqp, IB_WC_WR_FLUSH_ERR);
+		spin_unlock(&sqp->r_lock);
 
 		sqp->s_flags &= ~RVT_S_BUSY;
 		spin_unlock_irqrestore(&sqp->s_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe.c
@@ -35,6 +35,8 @@
 
 	if (rxe->tfm)
 		crypto_free_shash(rxe->tfm);
+
+	mutex_destroy(&rxe->usdev_lock);
 }
 
 /* initialize rxe device parameters */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_comp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_comp.c
@@ -124,12 +124,12 @@
 {
 	int must_sched;
 
-	skb_queue_tail(&qp->resp_pkts, skb);
-
-	must_sched = skb_queue_len(&qp->resp_pkts) > 1;
+	must_sched = skb_queue_len(&qp->resp_pkts) > 0;
 	if (must_sched != 0)
 		rxe_counter_inc(SKB_TO_PKT(skb)->rxe, RXE_CNT_COMPLETER_SCHED);
 
+	skb_queue_tail(&qp->resp_pkts, skb);
+
 	rxe_run_task(&qp->comp.task, must_sched);
 }
 
@@ -142,10 +142,7 @@
 	/* we come here whether or not we found a response packet to see if
 	 * there are any posted WQEs
 	 */
-	if (qp->is_user)
-		wqe = queue_head(qp->sq.queue, QUEUE_TYPE_FROM_USER);
-	else
-		wqe = queue_head(qp->sq.queue, QUEUE_TYPE_KERNEL);
+	wqe = queue_head(qp->sq.queue, QUEUE_TYPE_FROM_CLIENT);
 	*wqe_p = wqe;
 
 	/* no WQE or requester has not started it yet */
@@ -432,10 +429,7 @@
 	if (post)
 		make_send_cqe(qp, wqe, &cqe);
 
-	if (qp->is_user)
-		advance_consumer(qp->sq.queue, QUEUE_TYPE_FROM_USER);
-	else
-		advance_consumer(qp->sq.queue, QUEUE_TYPE_KERNEL);
+	queue_advance_consumer(qp->sq.queue, QUEUE_TYPE_FROM_CLIENT);
 
 	if (post)
 		rxe_cq_post(qp->scq, &cqe, 0);
@@ -539,7 +533,7 @@
 			wqe->status = IB_WC_WR_FLUSH_ERR;
 			do_complete(qp, wqe);
 		} else {
-			advance_consumer(q, q->type);
+			queue_advance_consumer(q, q->type);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_cq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_cq.c
@@ -25,11 +25,7 @@
 	}
 
 	if (cq) {
-		if (cq->is_user)
-			count = queue_count(cq->queue, QUEUE_TYPE_TO_USER);
-		else
-			count = queue_count(cq->queue, QUEUE_TYPE_KERNEL);
-
+		count = queue_count(cq->queue, QUEUE_TYPE_TO_CLIENT);
 		if (cqe < count) {
 			pr_warn("cqe(%d) < current # elements in queue (%d)",
 				cqe, count);
@@ -65,7 +61,7 @@
 	int err;
 	enum queue_type type;
 
-	type = uresp ? QUEUE_TYPE_TO_USER : QUEUE_TYPE_KERNEL;
+	type = QUEUE_TYPE_TO_CLIENT;
 	cq->queue = rxe_queue_init(rxe, &cqe,
 			sizeof(struct rxe_cqe), type);
 	if (!cq->queue) {
@@ -117,11 +113,7 @@
 
 	spin_lock_irqsave(&cq->cq_lock, flags);
 
-	if (cq->is_user)
-		full = queue_full(cq->queue, QUEUE_TYPE_TO_USER);
-	else
-		full = queue_full(cq->queue, QUEUE_TYPE_KERNEL);
-
+	full = queue_full(cq->queue, QUEUE_TYPE_TO_CLIENT);
 	if (unlikely(full)) {
 		spin_unlock_irqrestore(&cq->cq_lock, flags);
 		if (cq->ibcq.event_handler) {
@@ -134,17 +126,10 @@
 		return -EBUSY;
 	}
 
-	if (cq->is_user)
-		addr = producer_addr(cq->queue, QUEUE_TYPE_TO_USER);
-	else
-		addr = producer_addr(cq->queue, QUEUE_TYPE_KERNEL);
-
+	addr = queue_producer_addr(cq->queue, QUEUE_TYPE_TO_CLIENT);
 	memcpy(addr, cqe, sizeof(*cqe));
 
-	if (cq->is_user)
-		advance_producer(cq->queue, QUEUE_TYPE_TO_USER);
-	else
-		advance_producer(cq->queue, QUEUE_TYPE_KERNEL);
+	queue_advance_producer(cq->queue, QUEUE_TYPE_TO_CLIENT);
 
 	spin_unlock_irqrestore(&cq->cq_lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_loc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_loc.h
@@ -85,7 +85,8 @@
 			 enum rxe_mr_lookup_type type);
 int mr_check_range(struct rxe_mr *mr, u64 iova, size_t length);
 int advance_dma_data(struct rxe_dma_info *dma, unsigned int length);
-int rxe_invalidate_mr(struct rxe_qp *qp, u32 rkey);
+int rxe_invalidate_mr(struct rxe_qp *qp, u32 key);
+int rxe_reg_fast_mr(struct rxe_qp *qp, struct rxe_send_wqe *wqe);
 int rxe_dereg_mr(struct ib_mr *ibmr, struct ib_udata *udata);
 void rxe_mr_cleanup(struct rxe_pool_entry *arg);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_mr.c
@@ -48,8 +48,14 @@
 	u32 lkey = mr->pelem.index << 8 | rxe_get_next_key(-1);
 	u32 rkey = (access & IB_ACCESS_REMOTE) ? lkey : 0;
 
-	mr->ibmr.lkey = lkey;
-	mr->ibmr.rkey = rkey;
+	/* set ibmr->l/rkey and also copy into private l/rkey
+	 * for user MRs these will always be the same
+	 * for cases where caller 'owns' the key portion
+	 * they may be different until REG_MR WQE is executed.
+	 */
+	mr->lkey = mr->ibmr.lkey = lkey;
+	mr->rkey = mr->ibmr.rkey = rkey;
+
 	mr->state = RXE_MR_STATE_INVALID;
 	mr->type = RXE_MR_TYPE_NONE;
 	mr->map_shift = ilog2(RXE_BUF_PER_MAP);
@@ -191,10 +197,8 @@
 {
 	int err;
 
-	rxe_mr_init(0, mr);
-
-	/* In fastreg, we also set the rkey */
-	mr->ibmr.rkey = mr->ibmr.lkey;
+	/* always allow remote access for FMRs */
+	rxe_mr_init(IB_ACCESS_REMOTE, mr);
 
 	err = rxe_mr_alloc(mr, max_pages);
 	if (err)
@@ -507,8 +511,8 @@
 	if (!mr)
 		return NULL;
 
-	if (unlikely((type == RXE_LOOKUP_LOCAL && mr_lkey(mr) != key) ||
-		     (type == RXE_LOOKUP_REMOTE && mr_rkey(mr) != key) ||
+	if (unlikely((type == RXE_LOOKUP_LOCAL && mr->lkey != key) ||
+		     (type == RXE_LOOKUP_REMOTE && mr->rkey != key) ||
 		     mr_pd(mr) != pd || (access && !(access & mr->access)) ||
 		     mr->state != RXE_MR_STATE_VALID)) {
 		rxe_drop_ref(mr);
@@ -518,22 +522,22 @@
 	return mr;
 }
 
-int rxe_invalidate_mr(struct rxe_qp *qp, u32 rkey)
+int rxe_invalidate_mr(struct rxe_qp *qp, u32 key)
 {
 	struct rxe_dev *rxe = to_rdev(qp->ibqp.device);
 	struct rxe_mr *mr;
 	int ret;
 
-	mr = rxe_pool_get_index(&rxe->mr_pool, rkey >> 8);
+	mr = rxe_pool_get_index(&rxe->mr_pool, key >> 8);
 	if (!mr) {
-		pr_err("%s: No MR for rkey %#x\n", __func__, rkey);
+		pr_err("%s: No MR for key %#x\n", __func__, key);
 		ret = -EINVAL;
 		goto err;
 	}
 
-	if (rkey != mr->ibmr.rkey) {
-		pr_err("%s: rkey (%#x) doesn't match mr->ibmr.rkey (%#x)\n",
-			__func__, rkey, mr->ibmr.rkey);
+	if (mr->rkey ? (key != mr->rkey) : (key != mr->lkey)) {
+		pr_err("%s: wr key (%#x) doesn't match mr key (%#x)\n",
+			__func__, key, (mr->rkey ? mr->rkey : mr->lkey));
 		ret = -EINVAL;
 		goto err_drop_ref;
 	}
@@ -554,6 +558,49 @@
 	return ret;
 }
 
+/* user can (re)register fast MR by executing a REG_MR WQE.
+ * user is expected to hold a reference on the ib mr until the
+ * WQE completes.
+ * Once a fast MR is created this is the only way to change the
+ * private keys. It is the responsibility of the user to maintain
+ * the ib mr keys in sync with rxe mr keys.
+ */
+int rxe_reg_fast_mr(struct rxe_qp *qp, struct rxe_send_wqe *wqe)
+{
+	struct rxe_mr *mr = to_rmr(wqe->wr.wr.reg.mr);
+	u32 key = wqe->wr.wr.reg.key;
+	u32 access = wqe->wr.wr.reg.access;
+
+	/* user can only register MR in free state */
+	if (unlikely(mr->state != RXE_MR_STATE_FREE)) {
+		pr_warn("%s: mr->lkey = 0x%x not free\n",
+			__func__, mr->lkey);
+		return -EINVAL;
+	}
+
+	/* user can only register mr with qp in same protection domain */
+	if (unlikely(qp->ibqp.pd != mr->ibmr.pd)) {
+		pr_warn("%s: qp->pd and mr->pd don't match\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	/* user is only allowed to change key portion of l/rkey */
+	if (unlikely((mr->lkey & ~0xff) != (key & ~0xff))) {
+		pr_warn("%s: key = 0x%x has wrong index mr->lkey = 0x%x\n",
+			__func__, key, mr->lkey);
+		return -EINVAL;
+	}
+
+	mr->access = access;
+	mr->lkey = key;
+	mr->rkey = (access & IB_ACCESS_REMOTE) ? key : 0;
+	mr->iova = wqe->wr.wr.reg.mr->iova;
+	mr->state = RXE_MR_STATE_VALID;
+
+	return 0;
+}
+
 int rxe_dereg_mr(struct ib_mr *ibmr, struct ib_udata *udata)
 {
 	struct rxe_mr *mr = to_rmr(ibmr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_mw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_mw.c
@@ -21,7 +21,7 @@
 	}
 
 	rxe_add_index(mw);
-	ibmw->rkey = (mw->pelem.index << 8) | rxe_get_next_key(-1);
+	mw->rkey = ibmw->rkey = (mw->pelem.index << 8) | rxe_get_next_key(-1);
 	mw->state = (mw->ibmw.type == IB_MW_TYPE_2) ?
 			RXE_MW_STATE_FREE : RXE_MW_STATE_VALID;
 	spin_lock_init(&mw->lock);
@@ -108,11 +108,6 @@
 		}
 	}
 
-	if (unlikely((wqe->wr.wr.mw.rkey & 0xff) == (mw->ibmw.rkey & 0xff))) {
-		pr_err_once("attempt to bind MW with same key\n");
-		return -EINVAL;
-	}
-
 	/* remaining checks only apply to a nonzero MR */
 	if (!mr)
 		return 0;
@@ -161,13 +156,9 @@
 static void rxe_do_bind_mw(struct rxe_qp *qp, struct rxe_send_wqe *wqe,
 		      struct rxe_mw *mw, struct rxe_mr *mr)
 {
-	u32 rkey;
-	u32 new_rkey;
-
-	rkey = mw->ibmw.rkey;
-	new_rkey = (rkey & 0xffffff00) | (wqe->wr.wr.mw.rkey & 0x000000ff);
+	u32 key = wqe->wr.wr.mw.rkey & 0xff;
 
-	mw->ibmw.rkey = new_rkey;
+	mw->rkey = (mw->rkey & ~0xff) | key;
 	mw->access = wqe->wr.wr.mw.access;
 	mw->state = RXE_MW_STATE_VALID;
 	mw->addr = wqe->wr.wr.mw.addr;
@@ -197,29 +188,29 @@
 	struct rxe_mw *mw;
 	struct rxe_mr *mr;
 	struct rxe_dev *rxe = to_rdev(qp->ibqp.device);
+	u32 mw_rkey = wqe->wr.wr.mw.mw_rkey;
+	u32 mr_lkey = wqe->wr.wr.mw.mr_lkey;
 	unsigned long flags;
 
-	mw = rxe_pool_get_index(&rxe->mw_pool,
-				wqe->wr.wr.mw.mw_rkey >> 8);
+	mw = rxe_pool_get_index(&rxe->mw_pool, mw_rkey >> 8);
 	if (unlikely(!mw)) {
 		ret = -EINVAL;
 		goto err;
 	}
 
-	if (unlikely(mw->ibmw.rkey != wqe->wr.wr.mw.mw_rkey)) {
+	if (unlikely(mw->rkey != mw_rkey)) {
 		ret = -EINVAL;
 		goto err_drop_mw;
 	}
 
 	if (likely(wqe->wr.wr.mw.length)) {
-		mr = rxe_pool_get_index(&rxe->mr_pool,
-					wqe->wr.wr.mw.mr_lkey >> 8);
+		mr = rxe_pool_get_index(&rxe->mr_pool, mr_lkey >> 8);
 		if (unlikely(!mr)) {
 			ret = -EINVAL;
 			goto err_drop_mw;
 		}
 
-		if (unlikely(mr->ibmr.lkey != wqe->wr.wr.mw.mr_lkey)) {
+		if (unlikely(mr->lkey != mr_lkey)) {
 			ret = -EINVAL;
 			goto err_drop_mr;
 		}
@@ -292,7 +283,7 @@
 		goto err;
 	}
 
-	if (rkey != mw->ibmw.rkey) {
+	if (rkey != mw->rkey) {
 		ret = -EINVAL;
 		goto err_drop_ref;
 	}
@@ -323,7 +314,7 @@
 	if (!mw)
 		return NULL;
 
-	if (unlikely((rxe_mw_rkey(mw) != rkey) || rxe_mw_pd(mw) != pd ||
+	if (unlikely((mw->rkey != rkey) || rxe_mw_pd(mw) != pd ||
 		     (mw->ibmw.type == IB_MW_TYPE_2 && mw->qp != qp) ||
 		     (mw->length == 0) ||
 		     (access && !(access & mw->access)) ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_net.c
@@ -179,6 +179,9 @@
 	pkt->mask = RXE_GRH_MASK;
 	pkt->paylen = be16_to_cpu(udph->len) - sizeof(*udph);
 
+	/* remove udp header */
+	skb_pull(skb, sizeof(struct udphdr));
+
 	rxe_rcv(skb);
 
 	return 0;
@@ -419,6 +422,9 @@
 		return -EIO;
 	}
 
+	/* remove udp header */
+	skb_pull(skb, sizeof(struct udphdr));
+
 	rxe_rcv(skb);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_opcode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_opcode.c
@@ -117,7 +117,7 @@
 		}
 	},
 	[IB_OPCODE_RC_SEND_MIDDLE]		= {
-		.name	= "IB_OPCODE_RC_SEND_MIDDLE]",
+		.name	= "IB_OPCODE_RC_SEND_MIDDLE",
 		.mask	= RXE_PAYLOAD_MASK | RXE_REQ_MASK | RXE_SEND_MASK
 				| RXE_MIDDLE_MASK,
 		.length = RXE_BTH_BYTES,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_param.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_param.h
@@ -103,6 +103,12 @@
 	RXE_INFLIGHT_SKBS_PER_QP_HIGH	= 64,
 	RXE_INFLIGHT_SKBS_PER_QP_LOW	= 16,
 
+	/* Max number of interations of each tasklet
+	 * before yielding the cpu to let other
+	 * work make progress
+	 */
+	RXE_MAX_ITERATIONS		= 1024,
+
 	/* Delay before calling arbiter timer */
 	RXE_NSEC_ARB_TIMER_DELAY	= 200,
 
@@ -113,7 +119,7 @@
 /* default/initial rxe port parameters */
 enum rxe_port_param {
 	RXE_PORT_GID_TBL_LEN		= 1024,
-	RXE_PORT_PORT_CAP_FLAGS		= RDMA_CORE_CAP_PROT_ROCE_UDP_ENCAP,
+	RXE_PORT_PORT_CAP_FLAGS		= IB_PORT_CM_SUP,
 	RXE_PORT_MAX_MSG_SZ		= 0x800000,
 	RXE_PORT_BAD_PKEY_CNTR		= 0,
 	RXE_PORT_QKEY_VIOL_CNTR		= 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_qp.c
@@ -195,6 +195,17 @@
 	spin_lock_init(&qp->grp_lock);
 	spin_lock_init(&qp->state_lock);
 
+	spin_lock_init(&qp->req.task.state_lock);
+	spin_lock_init(&qp->resp.task.state_lock);
+	spin_lock_init(&qp->comp.task.state_lock);
+
+	spin_lock_init(&qp->sq.sq_lock);
+	spin_lock_init(&qp->rq.producer_lock);
+	spin_lock_init(&qp->rq.consumer_lock);
+
+	skb_queue_head_init(&qp->req_pkts);
+	skb_queue_head_init(&qp->resp_pkts);
+
 	atomic_set(&qp->ssn, 0);
 	atomic_set(&qp->skb_out, 0);
 }
@@ -231,7 +242,7 @@
 	qp->sq.max_inline = init->cap.max_inline_data = wqe_size;
 	wqe_size += sizeof(struct rxe_send_wqe);
 
-	type = uresp ? QUEUE_TYPE_FROM_USER : QUEUE_TYPE_KERNEL;
+	type = QUEUE_TYPE_FROM_CLIENT;
 	qp->sq.queue = rxe_queue_init(rxe, &qp->sq.max_wr,
 				wqe_size, type);
 	if (!qp->sq.queue)
@@ -248,24 +259,15 @@
 		return err;
 	}
 
-	if (qp->is_user)
-		qp->req.wqe_index = producer_index(qp->sq.queue,
-						QUEUE_TYPE_FROM_USER);
-	else
-		qp->req.wqe_index = producer_index(qp->sq.queue,
-						QUEUE_TYPE_KERNEL);
+	qp->req.wqe_index = queue_get_producer(qp->sq.queue,
+					       QUEUE_TYPE_FROM_CLIENT);
 
 	qp->req.state		= QP_STATE_RESET;
 	qp->req.opcode		= -1;
 	qp->comp.opcode		= -1;
 
-	spin_lock_init(&qp->sq.sq_lock);
-	skb_queue_head_init(&qp->req_pkts);
-
-	rxe_init_task(rxe, &qp->req.task, qp,
-		      rxe_requester, "req");
-	rxe_init_task(rxe, &qp->comp.task, qp,
-		      rxe_completer, "comp");
+	rxe_init_task(&qp->req.task, qp, rxe_requester);
+	rxe_init_task(&qp->comp.task, qp, rxe_completer);
 
 	qp->qp_timeout_jiffies = 0; /* Can't be set for UD/UC in modify_qp */
 	if (init->qp_type == IB_QPT_RC) {
@@ -293,7 +295,7 @@
 		pr_debug("qp#%d max_wr = %d, max_sge = %d, wqe_size = %d\n",
 			 qp_num(qp), qp->rq.max_wr, qp->rq.max_sge, wqe_size);
 
-		type = uresp ? QUEUE_TYPE_FROM_USER : QUEUE_TYPE_KERNEL;
+		type = QUEUE_TYPE_FROM_CLIENT;
 		qp->rq.queue = rxe_queue_init(rxe, &qp->rq.max_wr,
 					wqe_size, type);
 		if (!qp->rq.queue)
@@ -310,15 +312,7 @@
 		}
 	}
 
-	spin_lock_init(&qp->rq.producer_lock);
-	spin_lock_init(&qp->rq.consumer_lock);
-
-	qp->rq.is_user = qp->is_user;
-
-	skb_queue_head_init(&qp->resp_pkts);
-
-	rxe_init_task(rxe, &qp->resp.task, qp,
-		      rxe_responder, "resp");
+	rxe_init_task(&qp->resp.task, qp, rxe_responder);
 
 	qp->resp.opcode		= OPCODE_NONE;
 	qp->resp.msn		= 0;
@@ -367,6 +361,7 @@
 
 err2:
 	rxe_queue_cleanup(qp->sq.queue);
+	qp->sq.queue = NULL;
 err1:
 	qp->pd = NULL;
 	qp->rcq = NULL;
@@ -794,7 +789,9 @@
 	rxe_cleanup_task(&qp->comp.task);
 
 	/* flush out any receive wr's or pending requests */
-	__rxe_do_task(&qp->req.task);
+	if (qp->req.task.func)
+		__rxe_do_task(&qp->req.task);
+
 	if (qp->sq.queue) {
 		__rxe_do_task(&qp->comp.task);
 		__rxe_do_task(&qp->req.task);
@@ -829,13 +826,15 @@
 		qp->resp.mr = NULL;
 	}
 
-	if (qp_type(qp) == IB_QPT_RC)
-		sk_dst_reset(qp->sk->sk);
-
 	free_rd_atomic_resources(qp);
 
-	kernel_sock_shutdown(qp->sk, SHUT_RDWR);
-	sock_release(qp->sk);
+	if (qp->sk) {
+		if (qp_type(qp) == IB_QPT_RC)
+			sk_dst_reset(qp->sk->sk);
+
+		kernel_sock_shutdown(qp->sk, SHUT_RDWR);
+		sock_release(qp->sk);
+	}
 }
 
 /* called when the last reference to the qp is dropped */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_queue.c
@@ -111,17 +111,35 @@
 static int resize_finish(struct rxe_queue *q, struct rxe_queue *new_q,
 			 unsigned int num_elem)
 {
-	if (!queue_empty(q, q->type) && (num_elem < queue_count(q, q->type)))
+	enum queue_type type = q->type;
+	u32 new_prod;
+	u32 prod;
+	u32 cons;
+
+	if (!queue_empty(q, q->type) && (num_elem < queue_count(q, type)))
 		return -EINVAL;
 
-	while (!queue_empty(q, q->type)) {
-		memcpy(producer_addr(new_q, new_q->type),
-					consumer_addr(q, q->type),
-					new_q->elem_size);
-		advance_producer(new_q, new_q->type);
-		advance_consumer(q, q->type);
+	new_prod = queue_get_producer(new_q, type);
+	prod = queue_get_producer(q, type);
+	cons = queue_get_consumer(q, type);
+
+	while ((prod - cons) & q->index_mask) {
+		memcpy(queue_addr_from_index(new_q, new_prod),
+		       queue_addr_from_index(q, cons), new_q->elem_size);
+		new_prod = queue_next_index(new_q, new_prod);
+		cons = queue_next_index(q, cons);
 	}
 
+	new_q->buf->producer_index = new_prod;
+	q->buf->consumer_index = cons;
+
+	/* update private index copies */
+	if (type == QUEUE_TYPE_TO_CLIENT)
+		new_q->index = new_q->buf->producer_index;
+	else
+		q->index = q->buf->consumer_index;
+
+	/* exchange rxe_queue headers */
 	swap(*q, *new_q);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_queue.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_queue.h
@@ -10,34 +10,47 @@
 /* for definition of shared struct rxe_queue_buf */
 #include <uapi/rdma/rdma_user_rxe.h>
 
-/* implements a simple circular buffer that can optionally be
- * shared between user space and the kernel and can be resized
- * the requested element size is rounded up to a power of 2
- * and the number of elements in the buffer is also rounded
- * up to a power of 2. Since the queue is empty when the
- * producer and consumer indices match the maximum capacity
- * of the queue is one less than the number of element slots
+/* Implements a simple circular buffer that is shared between user
+ * and the driver and can be resized. The requested element size is
+ * rounded up to a power of 2 and the number of elements in the buffer
+ * is also rounded up to a power of 2. Since the queue is empty when
+ * the producer and consumer indices match the maximum capacity of the
+ * queue is one less than the number of element slots.
  *
  * Notes:
- *   - Kernel space indices are always masked off to q->index_mask
- *   before storing so do not need to be checked on reads.
- *   - User space indices may be out of range and must be
- *   masked before use when read.
- *   - The kernel indices for shared queues must not be written
- *   by user space so a local copy is used and a shared copy is
- *   stored when the local copy changes.
+ *   - The driver indices are always masked off to q->index_mask
+ *     before storing so do not need to be checked on reads.
+ *   - The user whether user space or kernel is generally
+ *     not trusted so its parameters are masked to make sure
+ *     they do not access the queue out of bounds on reads.
+ *   - The driver indices for queues must not be written
+ *     by user so a local copy is used and a shared copy is
+ *     stored when the local copy is changed.
  *   - By passing the type in the parameter list separate from q
- *   the compiler can eliminate the switch statement when the
- *   actual queue type is known when the function is called.
- *   In the performance path this is done. In less critical
- *   paths just q->type is passed.
+ *     the compiler can eliminate the switch statement when the
+ *     actual queue type is known when the function is called at
+ *     compile time.
+ *   - These queues are lock free. The user and driver must protect
+ *     changes to their end of the queues with locks if more than one
+ *     CPU can be accessing it at the same time.
  */
 
-/* type of queue */
+/**
+ * enum queue_type - type of queue
+ * @QUEUE_TYPE_TO_CLIENT:	Queue is written by rxe driver and
+ *				read by client. Used by rxe driver only.
+ * @QUEUE_TYPE_FROM_CLIENT:	Queue is written by client and
+ *				read by rxe driver. Used by rxe driver only.
+ * @QUEUE_TYPE_TO_DRIVER:	Queue is written by client and
+ *				read by rxe driver. Used by kernel client only.
+ * @QUEUE_TYPE_FROM_DRIVER:	Queue is written by rxe driver and
+ *				read by client. Used by kernel client only.
+ */
 enum queue_type {
-	QUEUE_TYPE_KERNEL,
-	QUEUE_TYPE_TO_USER,
-	QUEUE_TYPE_FROM_USER,
+	QUEUE_TYPE_TO_CLIENT,
+	QUEUE_TYPE_FROM_CLIENT,
+	QUEUE_TYPE_TO_DRIVER,
+	QUEUE_TYPE_FROM_DRIVER,
 };
 
 struct rxe_queue {
@@ -69,238 +82,171 @@
 int rxe_queue_resize(struct rxe_queue *q, unsigned int *num_elem_p,
 		     unsigned int elem_size, struct ib_udata *udata,
 		     struct mminfo __user *outbuf,
-		     /* Protect producers while resizing queue */
-		     spinlock_t *producer_lock,
-		     /* Protect consumers while resizing queue */
-		     spinlock_t *consumer_lock);
+		     spinlock_t *producer_lock, spinlock_t *consumer_lock);
 
 void rxe_queue_cleanup(struct rxe_queue *queue);
 
-static inline int next_index(struct rxe_queue *q, int index)
+static inline u32 queue_next_index(struct rxe_queue *q, int index)
 {
-	return (index + 1) & q->buf->index_mask;
+	return (index + 1) & q->index_mask;
 }
 
-static inline int queue_empty(struct rxe_queue *q, enum queue_type type)
+static inline u32 queue_get_producer(const struct rxe_queue *q,
+				     enum queue_type type)
 {
 	u32 prod;
-	u32 cons;
 
 	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		/* protect user space index */
+	case QUEUE_TYPE_FROM_CLIENT:
+		/* protect user index */
 		prod = smp_load_acquire(&q->buf->producer_index);
-		cons = q->index;
 		break;
-	case QUEUE_TYPE_TO_USER:
+	case QUEUE_TYPE_TO_CLIENT:
 		prod = q->index;
-		/* protect user space index */
-		cons = smp_load_acquire(&q->buf->consumer_index);
 		break;
-	case QUEUE_TYPE_KERNEL:
+	case QUEUE_TYPE_FROM_DRIVER:
+		/* protect driver index */
+		prod = smp_load_acquire(&q->buf->producer_index);
+		break;
+	case QUEUE_TYPE_TO_DRIVER:
 		prod = q->buf->producer_index;
-		cons = q->buf->consumer_index;
 		break;
 	}
 
-	return ((prod - cons) & q->index_mask) == 0;
+	return prod;
 }
 
-static inline int queue_full(struct rxe_queue *q, enum queue_type type)
+static inline u32 queue_get_consumer(const struct rxe_queue *q,
+				     enum queue_type type)
 {
-	u32 prod;
 	u32 cons;
 
 	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		/* protect user space index */
-		prod = smp_load_acquire(&q->buf->producer_index);
+	case QUEUE_TYPE_FROM_CLIENT:
 		cons = q->index;
 		break;
-	case QUEUE_TYPE_TO_USER:
-		prod = q->index;
-		/* protect user space index */
+	case QUEUE_TYPE_TO_CLIENT:
+		/* protect user index */
 		cons = smp_load_acquire(&q->buf->consumer_index);
 		break;
-	case QUEUE_TYPE_KERNEL:
-		prod = q->buf->producer_index;
+	case QUEUE_TYPE_FROM_DRIVER:
 		cons = q->buf->consumer_index;
 		break;
+	case QUEUE_TYPE_TO_DRIVER:
+		/* protect driver index */
+		cons = smp_load_acquire(&q->buf->consumer_index);
+		break;
 	}
 
-	return ((prod + 1 - cons) & q->index_mask) == 0;
+	return cons;
 }
 
-static inline unsigned int queue_count(const struct rxe_queue *q,
-					enum queue_type type)
+static inline int queue_empty(struct rxe_queue *q, enum queue_type type)
 {
-	u32 prod;
-	u32 cons;
-
-	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		/* protect user space index */
-		prod = smp_load_acquire(&q->buf->producer_index);
-		cons = q->index;
-		break;
-	case QUEUE_TYPE_TO_USER:
-		prod = q->index;
-		/* protect user space index */
-		cons = smp_load_acquire(&q->buf->consumer_index);
-		break;
-	case QUEUE_TYPE_KERNEL:
-		prod = q->buf->producer_index;
-		cons = q->buf->consumer_index;
-		break;
-	}
+	u32 prod = queue_get_producer(q, type);
+	u32 cons = queue_get_consumer(q, type);
 
-	return (prod - cons) & q->index_mask;
+	return ((prod - cons) & q->index_mask) == 0;
 }
 
-static inline void advance_producer(struct rxe_queue *q, enum queue_type type)
+static inline int queue_full(struct rxe_queue *q, enum queue_type type)
 {
-	u32 prod;
+	u32 prod = queue_get_producer(q, type);
+	u32 cons = queue_get_consumer(q, type);
 
-	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		pr_warn_once("Normally kernel should not write user space index\n");
-		/* protect user space index */
-		prod = smp_load_acquire(&q->buf->producer_index);
-		prod = (prod + 1) & q->index_mask;
-		/* same */
-		smp_store_release(&q->buf->producer_index, prod);
-		break;
-	case QUEUE_TYPE_TO_USER:
-		prod = q->index;
-		q->index = (prod + 1) & q->index_mask;
-		q->buf->producer_index = q->index;
-		break;
-	case QUEUE_TYPE_KERNEL:
-		prod = q->buf->producer_index;
-		q->buf->producer_index = (prod + 1) & q->index_mask;
-		break;
-	}
+	return ((prod + 1 - cons) & q->index_mask) == 0;
 }
 
-static inline void advance_consumer(struct rxe_queue *q, enum queue_type type)
+static inline u32 queue_count(const struct rxe_queue *q,
+					enum queue_type type)
 {
-	u32 cons;
+	u32 prod = queue_get_producer(q, type);
+	u32 cons = queue_get_consumer(q, type);
 
-	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		cons = q->index;
-		q->index = (cons + 1) & q->index_mask;
-		q->buf->consumer_index = q->index;
-		break;
-	case QUEUE_TYPE_TO_USER:
-		pr_warn_once("Normally kernel should not write user space index\n");
-		/* protect user space index */
-		cons = smp_load_acquire(&q->buf->consumer_index);
-		cons = (cons + 1) & q->index_mask;
-		/* same */
-		smp_store_release(&q->buf->consumer_index, cons);
-		break;
-	case QUEUE_TYPE_KERNEL:
-		cons = q->buf->consumer_index;
-		q->buf->consumer_index = (cons + 1) & q->index_mask;
-		break;
-	}
+	return (prod - cons) & q->index_mask;
 }
 
-static inline void *producer_addr(struct rxe_queue *q, enum queue_type type)
+static inline void queue_advance_producer(struct rxe_queue *q,
+					  enum queue_type type)
 {
 	u32 prod;
 
 	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		/* protect user space index */
-		prod = smp_load_acquire(&q->buf->producer_index);
-		prod &= q->index_mask;
+	case QUEUE_TYPE_FROM_CLIENT:
+		pr_warn("%s: attempt to advance client index\n",
+			__func__);
 		break;
-	case QUEUE_TYPE_TO_USER:
+	case QUEUE_TYPE_TO_CLIENT:
 		prod = q->index;
+		prod = (prod + 1) & q->index_mask;
+		q->index = prod;
+		/* protect user index */
+		smp_store_release(&q->buf->producer_index, prod);
+		break;
+	case QUEUE_TYPE_FROM_DRIVER:
+		pr_warn("%s: attempt to advance driver index\n",
+			__func__);
 		break;
-	case QUEUE_TYPE_KERNEL:
+	case QUEUE_TYPE_TO_DRIVER:
 		prod = q->buf->producer_index;
+		prod = (prod + 1) & q->index_mask;
+		q->buf->producer_index = prod;
 		break;
 	}
-
-	return q->buf->data + (prod << q->log2_elem_size);
 }
 
-static inline void *consumer_addr(struct rxe_queue *q, enum queue_type type)
+static inline void queue_advance_consumer(struct rxe_queue *q,
+					  enum queue_type type)
 {
 	u32 cons;
 
 	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
+	case QUEUE_TYPE_FROM_CLIENT:
 		cons = q->index;
+		cons = (cons + 1) & q->index_mask;
+		q->index = cons;
+		/* protect user index */
+		smp_store_release(&q->buf->consumer_index, cons);
 		break;
-	case QUEUE_TYPE_TO_USER:
-		/* protect user space index */
-		cons = smp_load_acquire(&q->buf->consumer_index);
-		cons &= q->index_mask;
+	case QUEUE_TYPE_TO_CLIENT:
+		pr_warn("%s: attempt to advance client index\n",
+			__func__);
 		break;
-	case QUEUE_TYPE_KERNEL:
+	case QUEUE_TYPE_FROM_DRIVER:
 		cons = q->buf->consumer_index;
+		cons = (cons + 1) & q->index_mask;
+		q->buf->consumer_index = cons;
+		break;
+	case QUEUE_TYPE_TO_DRIVER:
+		pr_warn("%s: attempt to advance driver index\n",
+			__func__);
 		break;
 	}
-
-	return q->buf->data + (cons << q->log2_elem_size);
 }
 
-static inline unsigned int producer_index(struct rxe_queue *q,
-						enum queue_type type)
+static inline void *queue_producer_addr(struct rxe_queue *q,
+					enum queue_type type)
 {
-	u32 prod;
+	u32 prod = queue_get_producer(q, type);
 
-	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		/* protect user space index */
-		prod = smp_load_acquire(&q->buf->producer_index);
-		prod &= q->index_mask;
-		break;
-	case QUEUE_TYPE_TO_USER:
-		prod = q->index;
-		break;
-	case QUEUE_TYPE_KERNEL:
-		prod = q->buf->producer_index;
-		break;
-	}
-
-	return prod;
+	return q->buf->data + (prod << q->log2_elem_size);
 }
 
-static inline unsigned int consumer_index(struct rxe_queue *q,
-						enum queue_type type)
+static inline void *queue_consumer_addr(struct rxe_queue *q,
+					enum queue_type type)
 {
-	u32 cons;
-
-	switch (type) {
-	case QUEUE_TYPE_FROM_USER:
-		cons = q->index;
-		break;
-	case QUEUE_TYPE_TO_USER:
-		/* protect user space index */
-		cons = smp_load_acquire(&q->buf->consumer_index);
-		cons &= q->index_mask;
-		break;
-	case QUEUE_TYPE_KERNEL:
-		cons = q->buf->consumer_index;
-		break;
-	}
+	u32 cons = queue_get_consumer(q, type);
 
-	return cons;
+	return q->buf->data + (cons << q->log2_elem_size);
 }
 
-static inline void *addr_from_index(struct rxe_queue *q,
-				unsigned int index)
+static inline void *queue_addr_from_index(struct rxe_queue *q, u32 index)
 {
 	return q->buf->data + ((index & q->index_mask)
-				<< q->buf->log2_elem_size);
+				<< q->log2_elem_size);
 }
 
-static inline unsigned int index_from_addr(const struct rxe_queue *q,
+static inline u32 queue_index_from_addr(const struct rxe_queue *q,
 				const void *addr)
 {
 	return (((u8 *)addr - q->buf->data) >> q->log2_elem_size)
@@ -309,7 +255,7 @@
 
 static inline void *queue_head(struct rxe_queue *q, enum queue_type type)
 {
-	return queue_empty(q, type) ? NULL : consumer_addr(q, type);
+	return queue_empty(q, type) ? NULL : queue_consumer_addr(q, type);
 }
 
 #endif /* RXE_QUEUE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_req.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_req.c
@@ -49,21 +49,16 @@
 	unsigned int cons;
 	unsigned int prod;
 
-	if (qp->is_user) {
-		cons = consumer_index(q, QUEUE_TYPE_FROM_USER);
-		prod = producer_index(q, QUEUE_TYPE_FROM_USER);
-	} else {
-		cons = consumer_index(q, QUEUE_TYPE_KERNEL);
-		prod = producer_index(q, QUEUE_TYPE_KERNEL);
-	}
+	cons = queue_get_consumer(q, QUEUE_TYPE_FROM_CLIENT);
+	prod = queue_get_producer(q, QUEUE_TYPE_FROM_CLIENT);
 
 	qp->req.wqe_index	= cons;
 	qp->req.psn		= qp->comp.psn;
 	qp->req.opcode		= -1;
 
 	for (wqe_index = cons; wqe_index != prod;
-			wqe_index = next_index(q, wqe_index)) {
-		wqe = addr_from_index(qp->sq.queue, wqe_index);
+			wqe_index = queue_next_index(q, wqe_index)) {
+		wqe = queue_addr_from_index(qp->sq.queue, wqe_index);
 		mask = wr_opcode_mask(wqe->wr.opcode, qp);
 
 		if (wqe->state == wqe_state_posted)
@@ -121,15 +116,9 @@
 	unsigned int cons;
 	unsigned int prod;
 
-	if (qp->is_user) {
-		wqe = queue_head(q, QUEUE_TYPE_FROM_USER);
-		cons = consumer_index(q, QUEUE_TYPE_FROM_USER);
-		prod = producer_index(q, QUEUE_TYPE_FROM_USER);
-	} else {
-		wqe = queue_head(q, QUEUE_TYPE_KERNEL);
-		cons = consumer_index(q, QUEUE_TYPE_KERNEL);
-		prod = producer_index(q, QUEUE_TYPE_KERNEL);
-	}
+	wqe = queue_head(q, QUEUE_TYPE_FROM_CLIENT);
+	cons = queue_get_consumer(q, QUEUE_TYPE_FROM_CLIENT);
+	prod = queue_get_producer(q, QUEUE_TYPE_FROM_CLIENT);
 
 	if (unlikely(qp->req.state == QP_STATE_DRAIN)) {
 		/* check to see if we are drained;
@@ -170,7 +159,7 @@
 	if (index == prod)
 		return NULL;
 
-	wqe = addr_from_index(q, index);
+	wqe = queue_addr_from_index(q, index);
 
 	if (unlikely((qp->req.state == QP_STATE_DRAIN ||
 		      qp->req.state == QP_STATE_DRAINED) &&
@@ -385,7 +374,7 @@
 	int			solicited;
 	u16			pkey;
 	u32			qp_num;
-	int			ack_req;
+	int			ack_req = 0;
 
 	/* length from start of bth to end of icrc */
 	paylen = rxe_opcode[opcode].length + payload + pad + RXE_ICRC_SIZE;
@@ -418,8 +407,9 @@
 	qp_num = (pkt->mask & RXE_DETH_MASK) ? ibwr->wr.ud.remote_qpn :
 					 qp->attr.dest_qp_num;
 
-	ack_req = ((pkt->mask & RXE_END_MASK) ||
-		(qp->req.noack_pkts++ > RXE_MAX_PKT_PER_ACK));
+	if (qp_type(qp) != IB_QPT_UD && qp_type(qp) != IB_QPT_UC)
+		ack_req = ((pkt->mask & RXE_END_MASK) ||
+			   (qp->req.noack_pkts++ > RXE_MAX_PKT_PER_ACK));
 	if (ack_req)
 		qp->req.noack_pkts = 0;
 
@@ -560,7 +550,8 @@
 	qp->req.opcode = pkt->opcode;
 
 	if (pkt->mask & RXE_END_MASK)
-		qp->req.wqe_index = next_index(qp->sq.queue, qp->req.wqe_index);
+		qp->req.wqe_index = queue_next_index(qp->sq.queue,
+						     qp->req.wqe_index);
 
 	qp->need_req_skb = 0;
 
@@ -572,7 +563,6 @@
 static int rxe_do_local_ops(struct rxe_qp *qp, struct rxe_send_wqe *wqe)
 {
 	u8 opcode = wqe->wr.opcode;
-	struct rxe_mr *mr;
 	u32 rkey;
 	int ret;
 
@@ -590,14 +580,11 @@
 		}
 		break;
 	case IB_WR_REG_MR:
-		mr = to_rmr(wqe->wr.wr.reg.mr);
-		rxe_add_ref(mr);
-		mr->state = RXE_MR_STATE_VALID;
-		mr->access = wqe->wr.wr.reg.access;
-		mr->ibmr.lkey = wqe->wr.wr.reg.key;
-		mr->ibmr.rkey = wqe->wr.wr.reg.key;
-		mr->iova = wqe->wr.wr.reg.mr->iova;
-		rxe_drop_ref(mr);
+		ret = rxe_reg_fast_mr(qp, wqe);
+		if (unlikely(ret)) {
+			wqe->status = IB_WC_LOC_QP_OP_ERR;
+			return ret;
+		}
 		break;
 	case IB_WR_BIND_MW:
 		ret = rxe_bind_mw(qp, wqe);
@@ -614,11 +601,13 @@
 
 	wqe->state = wqe_state_done;
 	wqe->status = IB_WC_SUCCESS;
-	qp->req.wqe_index = next_index(qp->sq.queue, qp->req.wqe_index);
+	qp->req.wqe_index = queue_next_index(qp->sq.queue, qp->req.wqe_index);
 
-	if ((wqe->wr.send_flags & IB_SEND_SIGNALED) ||
-	    qp->sq_sig_type == IB_SIGNAL_ALL_WR)
-		rxe_run_task(&qp->comp.task, 1);
+	/* There is no ack coming for local work requests
+	 * which can lead to a deadlock. So go ahead and complete
+	 * it now.
+	 */
+	rxe_run_task(&qp->comp.task, 1);
 
 	return 0;
 }
@@ -645,7 +634,8 @@
 		goto exit;
 
 	if (unlikely(qp->req.state == QP_STATE_RESET)) {
-		qp->req.wqe_index = consumer_index(q, q->type);
+		qp->req.wqe_index = queue_get_consumer(q,
+						QUEUE_TYPE_FROM_CLIENT);
 		qp->req.opcode = -1;
 		qp->req.need_rd_atomic = 0;
 		qp->req.wait_psn = 0;
@@ -687,7 +677,7 @@
 	opcode = next_opcode(qp, wqe, wqe->wr.opcode);
 	if (unlikely(opcode < 0)) {
 		wqe->status = IB_WC_LOC_QP_OP_ERR;
-		goto exit;
+		goto err;
 	}
 
 	mask = rxe_opcode[opcode].mask;
@@ -711,7 +701,7 @@
 			wqe->last_psn = qp->req.psn;
 			qp->req.psn = (qp->req.psn + 1) & BTH_PSN_MASK;
 			qp->req.opcode = IB_OPCODE_UD_SEND_ONLY;
-			qp->req.wqe_index = next_index(qp->sq.queue,
+			qp->req.wqe_index = queue_next_index(qp->sq.queue,
 						       qp->req.wqe_index);
 			wqe->state = wqe_state_done;
 			wqe->status = IB_WC_SUCCESS;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_resp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_resp.c
@@ -303,10 +303,7 @@
 
 	spin_lock_bh(&srq->rq.consumer_lock);
 
-	if (qp->is_user)
-		wqe = queue_head(q, QUEUE_TYPE_FROM_USER);
-	else
-		wqe = queue_head(q, QUEUE_TYPE_KERNEL);
+	wqe = queue_head(q, QUEUE_TYPE_FROM_CLIENT);
 	if (!wqe) {
 		spin_unlock_bh(&srq->rq.consumer_lock);
 		return RESPST_ERR_RNR;
@@ -322,13 +319,8 @@
 	memcpy(&qp->resp.srq_wqe, wqe, size);
 
 	qp->resp.wqe = &qp->resp.srq_wqe.wqe;
-	if (qp->is_user) {
-		advance_consumer(q, QUEUE_TYPE_FROM_USER);
-		count = queue_count(q, QUEUE_TYPE_FROM_USER);
-	} else {
-		advance_consumer(q, QUEUE_TYPE_KERNEL);
-		count = queue_count(q, QUEUE_TYPE_KERNEL);
-	}
+	queue_advance_consumer(q, QUEUE_TYPE_FROM_CLIENT);
+	count = queue_count(q, QUEUE_TYPE_FROM_CLIENT);
 
 	if (srq->limit && srq->ibsrq.event_handler && (count < srq->limit)) {
 		srq->limit = 0;
@@ -357,12 +349,8 @@
 			qp->resp.status = IB_WC_WR_FLUSH_ERR;
 			return RESPST_COMPLETE;
 		} else if (!srq) {
-			if (qp->is_user)
-				qp->resp.wqe = queue_head(qp->rq.queue,
-						QUEUE_TYPE_FROM_USER);
-			else
-				qp->resp.wqe = queue_head(qp->rq.queue,
-						QUEUE_TYPE_KERNEL);
+			qp->resp.wqe = queue_head(qp->rq.queue,
+					QUEUE_TYPE_FROM_CLIENT);
 			if (qp->resp.wqe) {
 				qp->resp.status = IB_WC_WR_FLUSH_ERR;
 				return RESPST_COMPLETE;
@@ -389,12 +377,8 @@
 		if (srq)
 			return get_srq_wqe(qp);
 
-		if (qp->is_user)
-			qp->resp.wqe = queue_head(qp->rq.queue,
-					QUEUE_TYPE_FROM_USER);
-		else
-			qp->resp.wqe = queue_head(qp->rq.queue,
-					QUEUE_TYPE_KERNEL);
+		qp->resp.wqe = queue_head(qp->rq.queue,
+				QUEUE_TYPE_FROM_CLIENT);
 		return (qp->resp.wqe) ? RESPST_CHK_LENGTH : RESPST_ERR_RNR;
 	}
 
@@ -830,6 +814,10 @@
 			return RESPST_ERR_INVALIDATE_RKEY;
 	}
 
+	if (pkt->mask & RXE_END_MASK)
+		/* We successfully processed this new request. */
+		qp->resp.msn++;
+
 	/* next expected psn, read handles this separately */
 	qp->resp.psn = (pkt->psn + 1) & BTH_PSN_MASK;
 	qp->resp.ack_psn = qp->resp.psn;
@@ -837,11 +825,9 @@
 	qp->resp.opcode = pkt->opcode;
 	qp->resp.status = IB_WC_SUCCESS;
 
-	if (pkt->mask & RXE_COMP_MASK) {
-		/* We successfully processed this new request. */
-		qp->resp.msn++;
+	if (pkt->mask & RXE_COMP_MASK)
 		return RESPST_COMPLETE;
-	} else if (qp_type(qp) == IB_QPT_RC)
+	else if (qp_type(qp) == IB_QPT_RC)
 		return RESPST_ACKNOWLEDGE;
 	else
 		return RESPST_CLEANUP;
@@ -936,12 +922,8 @@
 	}
 
 	/* have copy for srq and reference for !srq */
-	if (!qp->srq) {
-		if (qp->is_user)
-			advance_consumer(qp->rq.queue, QUEUE_TYPE_FROM_USER);
-		else
-			advance_consumer(qp->rq.queue, QUEUE_TYPE_KERNEL);
-	}
+	if (!qp->srq)
+		queue_advance_consumer(qp->rq.queue, QUEUE_TYPE_FROM_CLIENT);
 
 	qp->resp.wqe = NULL;
 
@@ -1213,7 +1195,7 @@
 		return;
 
 	while (!qp->srq && q && queue_head(q, q->type))
-		advance_consumer(q, q->type);
+		queue_advance_consumer(q, q->type);
 }
 
 int rxe_responder(void *arg)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_srq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_srq.c
@@ -86,14 +86,13 @@
 	srq->srq_num		= srq->pelem.index;
 	srq->rq.max_wr		= init->attr.max_wr;
 	srq->rq.max_sge		= init->attr.max_sge;
-	srq->rq.is_user		= srq->is_user;
 
 	srq_wqe_size		= rcv_wqe_size(srq->rq.max_sge);
 
 	spin_lock_init(&srq->rq.producer_lock);
 	spin_lock_init(&srq->rq.consumer_lock);
 
-	type = uresp ? QUEUE_TYPE_FROM_USER : QUEUE_TYPE_KERNEL;
+	type = QUEUE_TYPE_FROM_CLIENT;
 	q = rxe_queue_init(rxe, &srq->rq.max_wr,
 			srq_wqe_size, type);
 	if (!q) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_task.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_task.c
@@ -8,7 +8,7 @@
 #include <linux/interrupt.h>
 #include <linux/hardirq.h>
 
-#include "rxe_task.h"
+#include "rxe.h"
 
 int __rxe_do_task(struct rxe_task *task)
 
@@ -34,6 +34,7 @@
 	int ret;
 	unsigned long flags;
 	struct rxe_task *task = from_tasklet(task, t, tasklet);
+	unsigned int iterations = RXE_MAX_ITERATIONS;
 
 	spin_lock_irqsave(&task->state_lock, flags);
 	switch (task->state) {
@@ -62,13 +63,20 @@
 		spin_lock_irqsave(&task->state_lock, flags);
 		switch (task->state) {
 		case TASK_STATE_BUSY:
-			if (ret)
+			if (ret) {
 				task->state = TASK_STATE_START;
-			else
+			} else if (iterations--) {
 				cont = 1;
+			} else {
+				/* reschedule the tasklet and exit
+				 * the loop to give up the cpu
+				 */
+				tasklet_schedule(&task->tasklet);
+				task->state = TASK_STATE_START;
+			}
 			break;
 
-		/* soneone tried to run the task since the last time we called
+		/* someone tried to run the task since the last time we called
 		 * func, so we will call one more time regardless of the
 		 * return value
 		 */
@@ -87,13 +95,10 @@
 	task->ret = ret;
 }
 
-int rxe_init_task(void *obj, struct rxe_task *task,
-		  void *arg, int (*func)(void *), char *name)
+int rxe_init_task(struct rxe_task *task, void *arg, int (*func)(void *))
 {
-	task->obj	= obj;
 	task->arg	= arg;
 	task->func	= func;
-	snprintf(task->name, sizeof(task->name), "%s", name);
 	task->destroyed	= false;
 
 	tasklet_setup(&task->tasklet, rxe_do_task);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_task.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_task.h
@@ -19,14 +19,12 @@
  * called again.
  */
 struct rxe_task {
-	void			*obj;
 	struct tasklet_struct	tasklet;
 	int			state;
 	spinlock_t		state_lock; /* spinlock for task state */
 	void			*arg;
 	int			(*func)(void *arg);
 	int			ret;
-	char			name[16];
 	bool			destroyed;
 };
 
@@ -35,8 +33,7 @@
  *	arg  => parameter to pass to fcn
  *	func => function to call until it returns != 0
  */
-int rxe_init_task(void *obj, struct rxe_task *task,
-		  void *arg, int (*func)(void *), char *name);
+int rxe_init_task(struct rxe_task *task, void *arg, int (*func)(void *));
 
 /* cleanup task */
 void rxe_cleanup_task(struct rxe_task *task);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_verbs.c
@@ -218,11 +218,7 @@
 	int num_sge = ibwr->num_sge;
 	int full;
 
-	if (rq->is_user)
-		full = queue_full(rq->queue, QUEUE_TYPE_FROM_USER);
-	else
-		full = queue_full(rq->queue, QUEUE_TYPE_KERNEL);
-
+	full = queue_full(rq->queue, QUEUE_TYPE_TO_DRIVER);
 	if (unlikely(full)) {
 		err = -ENOMEM;
 		goto err1;
@@ -237,11 +233,7 @@
 	for (i = 0; i < num_sge; i++)
 		length += ibwr->sg_list[i].length;
 
-	if (rq->is_user)
-		recv_wqe = producer_addr(rq->queue, QUEUE_TYPE_FROM_USER);
-	else
-		recv_wqe = producer_addr(rq->queue, QUEUE_TYPE_KERNEL);
-
+	recv_wqe = queue_producer_addr(rq->queue, QUEUE_TYPE_TO_DRIVER);
 	recv_wqe->wr_id = ibwr->wr_id;
 	recv_wqe->num_sge = num_sge;
 
@@ -254,10 +246,7 @@
 	recv_wqe->dma.cur_sge		= 0;
 	recv_wqe->dma.sge_offset	= 0;
 
-	if (rq->is_user)
-		advance_producer(rq->queue, QUEUE_TYPE_FROM_USER);
-	else
-		advance_producer(rq->queue, QUEUE_TYPE_KERNEL);
+	queue_advance_producer(rq->queue, QUEUE_TYPE_TO_DRIVER);
 
 	return 0;
 
@@ -281,9 +270,6 @@
 		if (udata->outlen < sizeof(*uresp))
 			return -EINVAL;
 		uresp = udata->outbuf;
-		srq->is_user = true;
-	} else {
-		srq->is_user = false;
 	}
 
 	err = rxe_srq_chk_attr(rxe, NULL, &init->attr, IB_SRQ_INIT_MASK);
@@ -633,27 +619,17 @@
 
 	spin_lock_irqsave(&qp->sq.sq_lock, flags);
 
-	if (qp->is_user)
-		full = queue_full(sq->queue, QUEUE_TYPE_FROM_USER);
-	else
-		full = queue_full(sq->queue, QUEUE_TYPE_KERNEL);
+	full = queue_full(sq->queue, QUEUE_TYPE_TO_DRIVER);
 
 	if (unlikely(full)) {
 		spin_unlock_irqrestore(&qp->sq.sq_lock, flags);
 		return -ENOMEM;
 	}
 
-	if (qp->is_user)
-		send_wqe = producer_addr(sq->queue, QUEUE_TYPE_FROM_USER);
-	else
-		send_wqe = producer_addr(sq->queue, QUEUE_TYPE_KERNEL);
-
+	send_wqe = queue_producer_addr(sq->queue, QUEUE_TYPE_TO_DRIVER);
 	init_send_wqe(qp, ibwr, mask, length, send_wqe);
 
-	if (qp->is_user)
-		advance_producer(sq->queue, QUEUE_TYPE_FROM_USER);
-	else
-		advance_producer(sq->queue, QUEUE_TYPE_KERNEL);
+	queue_advance_producer(sq->queue, QUEUE_TYPE_TO_DRIVER);
 
 	spin_unlock_irqrestore(&qp->sq.sq_lock, flags);
 
@@ -845,18 +821,12 @@
 
 	spin_lock_irqsave(&cq->cq_lock, flags);
 	for (i = 0; i < num_entries; i++) {
-		if (cq->is_user)
-			cqe = queue_head(cq->queue, QUEUE_TYPE_TO_USER);
-		else
-			cqe = queue_head(cq->queue, QUEUE_TYPE_KERNEL);
+		cqe = queue_head(cq->queue, QUEUE_TYPE_FROM_DRIVER);
 		if (!cqe)
 			break;
 
 		memcpy(wc++, &cqe->ibwc, sizeof(*wc));
-		if (cq->is_user)
-			advance_consumer(cq->queue, QUEUE_TYPE_TO_USER);
-		else
-			advance_consumer(cq->queue, QUEUE_TYPE_KERNEL);
+		queue_advance_consumer(cq->queue, QUEUE_TYPE_FROM_DRIVER);
 	}
 	spin_unlock_irqrestore(&cq->cq_lock, flags);
 
@@ -868,10 +838,7 @@
 	struct rxe_cq *cq = to_rcq(ibcq);
 	int count;
 
-	if (cq->is_user)
-		count = queue_count(cq->queue, QUEUE_TYPE_TO_USER);
-	else
-		count = queue_count(cq->queue, QUEUE_TYPE_KERNEL);
+	count = queue_count(cq->queue, QUEUE_TYPE_FROM_DRIVER);
 
 	return (count > wc_cnt) ? wc_cnt : count;
 }
@@ -887,10 +854,7 @@
 	if (cq->notify != IB_CQ_NEXT_COMP)
 		cq->notify = flags & IB_CQ_SOLICITED_MASK;
 
-	if (cq->is_user)
-		empty = queue_empty(cq->queue, QUEUE_TYPE_TO_USER);
-	else
-		empty = queue_empty(cq->queue, QUEUE_TYPE_KERNEL);
+	empty = queue_empty(cq->queue, QUEUE_TYPE_FROM_DRIVER);
 
 	if ((flags & IB_CQ_REPORT_MISSED_EVENTS) && !empty)
 		ret = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/rxe/rxe_verbs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/rxe/rxe_verbs.h
@@ -77,7 +77,6 @@
 };
 
 struct rxe_sq {
-	bool			is_user;
 	int			max_wr;
 	int			max_sge;
 	int			max_inline;
@@ -86,7 +85,6 @@
 };
 
 struct rxe_rq {
-	bool			is_user;
 	int			max_wr;
 	int			max_sge;
 	spinlock_t		producer_lock; /* guard queue producer */
@@ -100,7 +98,6 @@
 	struct rxe_pd		*pd;
 	struct rxe_rq		rq;
 	u32			srq_num;
-	bool			is_user;
 
 	int			limit;
 	int			error;
@@ -313,6 +310,8 @@
 
 	struct ib_umem		*umem;
 
+	u32			lkey;
+	u32			rkey;
 	enum rxe_mr_state	state;
 	enum rxe_mr_type	type;
 	u64			va;
@@ -350,6 +349,7 @@
 	enum rxe_mw_state	state;
 	struct rxe_qp		*qp; /* Type 2 only */
 	struct rxe_mr		*mr;
+	u32			rkey;
 	int			access;
 	u64			addr;
 	u64			length;
@@ -474,26 +474,11 @@
 	return to_rpd(mr->ibmr.pd);
 }
 
-static inline u32 mr_lkey(struct rxe_mr *mr)
-{
-	return mr->ibmr.lkey;
-}
-
-static inline u32 mr_rkey(struct rxe_mr *mr)
-{
-	return mr->ibmr.rkey;
-}
-
 static inline struct rxe_pd *rxe_mw_pd(struct rxe_mw *mw)
 {
 	return to_rpd(mw->ibmw.pd);
 }
 
-static inline u32 rxe_mw_rkey(struct rxe_mw *mw)
-{
-	return mw->ibmw.rkey;
-}
-
 int rxe_register_device(struct rxe_dev *rxe, const char *ibdev_name);
 
 void rxe_mc_cleanup(struct rxe_pool_entry *arg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw.h
@@ -418,6 +418,7 @@
 	struct ib_qp base_qp;
 	struct siw_device *sdev;
 	struct kref ref;
+	struct completion qp_free;
 	struct list_head devq;
 	int tx_cpu;
 	struct siw_qp_attrs attrs;
@@ -644,14 +645,9 @@
 	return &qp->orq[qp->orq_get % qp->attrs.orq_size];
 }
 
-static inline struct siw_sqe *orq_get_tail(struct siw_qp *qp)
-{
-	return &qp->orq[qp->orq_put % qp->attrs.orq_size];
-}
-
 static inline struct siw_sqe *orq_get_free(struct siw_qp *qp)
 {
-	struct siw_sqe *orq_e = orq_get_tail(qp);
+	struct siw_sqe *orq_e = &qp->orq[qp->orq_put % qp->attrs.orq_size];
 
 	if (READ_ONCE(orq_e->flags) == 0)
 		return orq_e;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_cm.c
@@ -725,11 +725,11 @@
 	enum mpa_v2_ctrl mpa_p2p_mode = MPA_V2_RDMA_NO_RTR;
 
 	rv = siw_recv_mpa_rr(cep);
-	if (rv != -EAGAIN)
-		siw_cancel_mpatimer(cep);
 	if (rv)
 		goto out_err;
 
+	siw_cancel_mpatimer(cep);
+
 	rep = &cep->mpa.hdr;
 
 	if (__mpa_rr_revision(rep->params.bits) > MPA_REVISION_2) {
@@ -895,7 +895,8 @@
 	}
 
 out_err:
-	siw_cm_upcall(cep, IW_CM_EVENT_CONNECT_REPLY, -EINVAL);
+	if (rv != -EAGAIN)
+		siw_cm_upcall(cep, IW_CM_EVENT_CONNECT_REPLY, -EINVAL);
 
 	return rv;
 }
@@ -968,14 +969,16 @@
 
 		siw_cep_set_inuse(new_cep);
 		rv = siw_proc_mpareq(new_cep);
-		siw_cep_set_free(new_cep);
-
 		if (rv != -EAGAIN) {
 			siw_cep_put(cep);
 			new_cep->listen_cep = NULL;
-			if (rv)
+			if (rv) {
+				siw_cancel_mpatimer(new_cep);
+				siw_cep_set_free(new_cep);
 				goto error;
+			}
 		}
+		siw_cep_set_free(new_cep);
 	}
 	return;
 
@@ -1095,9 +1098,12 @@
 				/*
 				 * Socket close before MPA request received.
 				 */
-				siw_dbg_cep(cep, "no mpareq: drop listener\n");
-				siw_cep_put(cep->listen_cep);
-				cep->listen_cep = NULL;
+				if (cep->listen_cep) {
+					siw_dbg_cep(cep,
+						"no mpareq: drop listener\n");
+					siw_cep_put(cep->listen_cep);
+					cep->listen_cep = NULL;
+				}
 			}
 		}
 		release_cep = 1;
@@ -1220,7 +1226,11 @@
 	if (!cep)
 		goto out;
 
-	siw_dbg_cep(cep, "state: %d\n", cep->state);
+	siw_dbg_cep(cep, "cep state: %d, socket state %d\n",
+		    cep->state, sk->sk_state);
+
+	if (sk->sk_state != TCP_ESTABLISHED)
+		goto out;
 
 	switch (cep->state) {
 	case SIW_EPSTATE_RDMA_MODE:
@@ -1494,7 +1504,6 @@
 
 		cep->cm_id = NULL;
 		id->rem_ref(id);
-		siw_cep_put(cep);
 
 		qp->cep = NULL;
 		siw_cep_put(cep);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_cq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_cq.c
@@ -56,8 +56,6 @@
 	if (READ_ONCE(cqe->flags) & SIW_WQE_VALID) {
 		memset(wc, 0, sizeof(*wc));
 		wc->wr_id = cqe->id;
-		wc->status = map_cqe_status[cqe->status].ib;
-		wc->opcode = map_wc_opcode[cqe->opcode];
 		wc->byte_len = cqe->bytes;
 
 		/*
@@ -71,10 +69,32 @@
 				wc->wc_flags = IB_WC_WITH_INVALIDATE;
 			}
 			wc->qp = cqe->base_qp;
+			wc->opcode = map_wc_opcode[cqe->opcode];
+			wc->status = map_cqe_status[cqe->status].ib;
 			siw_dbg_cq(cq,
 				   "idx %u, type %d, flags %2x, id 0x%pK\n",
 				   cq->cq_get % cq->num_cqe, cqe->opcode,
 				   cqe->flags, (void *)(uintptr_t)cqe->id);
+		} else {
+			/*
+			 * A malicious user may set invalid opcode or
+			 * status in the user mmapped CQE array.
+			 * Sanity check and correct values in that case
+			 * to avoid out-of-bounds access to global arrays
+			 * for opcode and status mapping.
+			 */
+			u8 opcode = cqe->opcode;
+			u16 status = cqe->status;
+
+			if (opcode >= SIW_NUM_OPCODES) {
+				opcode = 0;
+				status = SIW_WC_GENERAL_ERR;
+			} else if (status >= SIW_NUM_WC_STATUS) {
+				status = SIW_WC_GENERAL_ERR;
+			}
+			wc->opcode = map_wc_opcode[opcode];
+			wc->status = map_cqe_status[status].ib;
+
 		}
 		WRITE_ONCE(cqe->flags, 0);
 		cq->cq_get++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_main.c
@@ -437,9 +437,6 @@
 
 	dev_dbg(&netdev->dev, "siw: event %lu\n", event);
 
-	if (dev_net(netdev) != &init_net)
-		return NOTIFY_OK;
-
 	base_dev = ib_device_get_by_netdev(netdev, RDMA_DRIVER_SIW);
 	if (!base_dev)
 		return NOTIFY_OK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_mem.c
@@ -398,7 +398,7 @@
 
 	mlock_limit = rlimit(RLIMIT_MEMLOCK) >> PAGE_SHIFT;
 
-	if (num_pages + atomic64_read(&mm_s->pinned_vm) > mlock_limit) {
+	if (atomic64_add_return(num_pages, &mm_s->pinned_vm) > mlock_limit) {
 		rv = -ENOMEM;
 		goto out_sem_up;
 	}
@@ -411,18 +411,16 @@
 		goto out_sem_up;
 	}
 	for (i = 0; num_pages; i++) {
-		int got, nents = min_t(int, num_pages, PAGES_PER_CHUNK);
-
-		umem->page_chunk[i].plist =
+		int nents = min_t(int, num_pages, PAGES_PER_CHUNK);
+		struct page **plist =
 			kcalloc(nents, sizeof(struct page *), GFP_KERNEL);
-		if (!umem->page_chunk[i].plist) {
+
+		if (!plist) {
 			rv = -ENOMEM;
 			goto out_sem_up;
 		}
-		got = 0;
+		umem->page_chunk[i].plist = plist;
 		while (nents) {
-			struct page **plist = &umem->page_chunk[i].plist[got];
-
 			rv = pin_user_pages(first_page_va, nents,
 					    foll_flags | FOLL_LONGTERM,
 					    plist, NULL);
@@ -430,12 +428,11 @@
 				goto out_sem_up;
 
 			umem->num_pages += rv;
-			atomic64_add(rv, &mm_s->pinned_vm);
 			first_page_va += rv * PAGE_SIZE;
+			plist += rv;
 			nents -= rv;
-			got += rv;
+			num_pages -= rv;
 		}
-		num_pages -= got;
 	}
 out_sem_up:
 	mmap_read_unlock(mm_s);
@@ -443,6 +440,10 @@
 	if (rv > 0)
 		return umem;
 
+	/* Adjust accounting for pages not pinned */
+	if (num_pages)
+		atomic64_sub(num_pages, &mm_s->pinned_vm);
+
 	siw_umem_release(umem, false);
 
 	return ERR_PTR(rv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_qp.c
@@ -1342,6 +1342,6 @@
 	vfree(qp->orq);
 
 	siw_put_tx_cpu(qp->tx_cpu);
-
+	complete(&qp->qp_free);
 	atomic_dec(&sdev->num_qp);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_qp_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_qp_rx.c
@@ -961,27 +961,28 @@
 static int siw_get_trailer(struct siw_qp *qp, struct siw_rx_stream *srx)
 {
 	struct sk_buff *skb = srx->skb;
+	int avail = min(srx->skb_new, srx->fpdu_part_rem);
 	u8 *tbuf = (u8 *)&srx->trailer.crc - srx->pad;
 	__wsum crc_in, crc_own = 0;
 
 	siw_dbg_qp(qp, "expected %d, available %d, pad %u\n",
 		   srx->fpdu_part_rem, srx->skb_new, srx->pad);
 
-	if (srx->skb_new < srx->fpdu_part_rem)
-		return -EAGAIN;
-
-	skb_copy_bits(skb, srx->skb_offset, tbuf, srx->fpdu_part_rem);
+	skb_copy_bits(skb, srx->skb_offset, tbuf, avail);
 
-	if (srx->mpa_crc_hd && srx->pad)
-		crypto_shash_update(srx->mpa_crc_hd, tbuf, srx->pad);
+	srx->skb_new -= avail;
+	srx->skb_offset += avail;
+	srx->skb_copied += avail;
+	srx->fpdu_part_rem -= avail;
 
-	srx->skb_new -= srx->fpdu_part_rem;
-	srx->skb_offset += srx->fpdu_part_rem;
-	srx->skb_copied += srx->fpdu_part_rem;
+	if (srx->fpdu_part_rem)
+		return -EAGAIN;
 
 	if (!srx->mpa_crc_hd)
 		return 0;
 
+	if (srx->pad)
+		crypto_shash_update(srx->mpa_crc_hd, tbuf, srx->pad);
 	/*
 	 * CRC32 is computed, transmitted and received directly in NBO,
 	 * so there's never a reason to convert byte order.
@@ -1083,10 +1084,9 @@
 	 * completely received.
 	 */
 	if (iwarp_pktinfo[opcode].hdr_len > sizeof(struct iwarp_ctrl_tagged)) {
-		bytes = iwarp_pktinfo[opcode].hdr_len - MIN_DDP_HDR;
+		int hdrlen = iwarp_pktinfo[opcode].hdr_len;
 
-		if (srx->skb_new < bytes)
-			return -EAGAIN;
+		bytes = min_t(int, hdrlen - MIN_DDP_HDR, srx->skb_new);
 
 		skb_copy_bits(skb, srx->skb_offset,
 			      (char *)c_hdr + srx->fpdu_part_rcvd, bytes);
@@ -1096,6 +1096,9 @@
 		srx->skb_new -= bytes;
 		srx->skb_offset += bytes;
 		srx->skb_copied += bytes;
+
+		if (srx->fpdu_part_rcvd < hdrlen)
+			return -EAGAIN;
 	}
 
 	/*
@@ -1153,11 +1156,12 @@
 
 	spin_lock_irqsave(&qp->orq_lock, flags);
 
-	rreq = orq_get_current(qp);
-
 	/* free current orq entry */
+	rreq = orq_get_current(qp);
 	WRITE_ONCE(rreq->flags, 0);
 
+	qp->orq_get++;
+
 	if (qp->tx_ctx.orq_fence) {
 		if (unlikely(tx_waiting->wr_status != SIW_WR_QUEUED)) {
 			pr_warn("siw: [QP %u]: fence resume: bad status %d\n",
@@ -1165,10 +1169,12 @@
 			rv = -EPROTO;
 			goto out;
 		}
-		/* resume SQ processing */
+		/* resume SQ processing, if possible */
 		if (tx_waiting->sqe.opcode == SIW_OP_READ ||
 		    tx_waiting->sqe.opcode == SIW_OP_READ_LOCAL_INV) {
-			rreq = orq_get_tail(qp);
+
+			/* SQ processing was stopped because of a full ORQ */
+			rreq = orq_get_free(qp);
 			if (unlikely(!rreq)) {
 				pr_warn("siw: [QP %u]: no ORQE\n", qp_id(qp));
 				rv = -EPROTO;
@@ -1181,15 +1187,14 @@
 			resume_tx = 1;
 
 		} else if (siw_orq_empty(qp)) {
+			/*
+			 * SQ processing was stopped by fenced work request.
+			 * Resume since all previous Read's are now completed.
+			 */
 			qp->tx_ctx.orq_fence = 0;
 			resume_tx = 1;
-		} else {
-			pr_warn("siw: [QP %u]: fence resume: orq idx: %d:%d\n",
-				qp_id(qp), qp->orq_get, qp->orq_put);
-			rv = -EPROTO;
 		}
 	}
-	qp->orq_get++;
 out:
 	spin_unlock_irqrestore(&qp->orq_lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_qp_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_qp_tx.c
@@ -29,7 +29,7 @@
 	dma_addr_t paddr = siw_pbl_get_buffer(pbl, offset, NULL, idx);
 
 	if (paddr)
-		return virt_to_page(paddr);
+		return virt_to_page((void *)(uintptr_t)paddr);
 
 	return NULL;
 }
@@ -533,13 +533,23 @@
 					kunmap_local(kaddr);
 				}
 			} else {
-				u64 va = sge->laddr + sge_off;
-
-				page_array[seg] = virt_to_page(va & PAGE_MASK);
+				/*
+				 * Cast to an uintptr_t to preserve all 64 bits
+				 * in sge->laddr.
+				 */
+				uintptr_t va = (uintptr_t)(sge->laddr + sge_off);
+
+				/*
+				 * virt_to_page() takes a (void *) pointer
+				 * so cast to a (void *) meaning it will be 64
+				 * bits on a 64 bit platform and 32 bits on a
+				 * 32 bit platform.
+				 */
+				page_array[seg] = virt_to_page((void *)(va & PAGE_MASK));
 				if (do_crc)
 					crypto_shash_update(
 						c_tx->mpa_crc_hd,
-						(void *)(uintptr_t)va,
+						(void *)va,
 						plen);
 			}
 
@@ -548,7 +558,7 @@
 			data_len -= plen;
 			fp_off = 0;
 
-			if (++seg > (int)MAX_ARRAY) {
+			if (++seg >= (int)MAX_ARRAY) {
 				siw_dbg_qp(tx_qp(c_tx), "to many fragments\n");
 				siw_unmap_pages(iov, kmap_mask, seg-1);
 				wqe->processed -= c_tx->bytes_unsent;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/sw/siw/siw_verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/sw/siw/siw_verbs.c
@@ -311,7 +311,8 @@
 
 	if (atomic_inc_return(&sdev->num_qp) > SIW_MAX_QP) {
 		siw_dbg(base_dev, "too many QP's\n");
-		return -ENOMEM;
+		rv = -ENOMEM;
+		goto err_atomic;
 	}
 	if (attrs->qp_type != IB_QPT_RC) {
 		siw_dbg(base_dev, "only RC QP's supported\n");
@@ -477,6 +478,8 @@
 	list_add_tail(&qp->devq, &sdev->qp_list);
 	spin_unlock_irqrestore(&sdev->lock, flags);
 
+	init_completion(&qp->qp_free);
+
 	return 0;
 
 err_out_xa:
@@ -621,6 +624,7 @@
 	qp->scq = qp->rcq = NULL;
 
 	siw_qp_put(qp);
+	wait_for_completion(&qp->qp_free);
 
 	return 0;
 }
@@ -670,13 +674,45 @@
 static int siw_sq_flush_wr(struct siw_qp *qp, const struct ib_send_wr *wr,
 			   const struct ib_send_wr **bad_wr)
 {
-	struct siw_sqe sqe = {};
 	int rv = 0;
 
 	while (wr) {
-		sqe.id = wr->wr_id;
-		sqe.opcode = wr->opcode;
-		rv = siw_sqe_complete(qp, &sqe, 0, SIW_WC_WR_FLUSH_ERR);
+		struct siw_sqe sqe = {};
+
+		switch (wr->opcode) {
+		case IB_WR_RDMA_WRITE:
+			sqe.opcode = SIW_OP_WRITE;
+			break;
+		case IB_WR_RDMA_READ:
+			sqe.opcode = SIW_OP_READ;
+			break;
+		case IB_WR_RDMA_READ_WITH_INV:
+			sqe.opcode = SIW_OP_READ_LOCAL_INV;
+			break;
+		case IB_WR_SEND:
+			sqe.opcode = SIW_OP_SEND;
+			break;
+		case IB_WR_SEND_WITH_IMM:
+			sqe.opcode = SIW_OP_SEND_WITH_IMM;
+			break;
+		case IB_WR_SEND_WITH_INV:
+			sqe.opcode = SIW_OP_SEND_REMOTE_INV;
+			break;
+		case IB_WR_LOCAL_INV:
+			sqe.opcode = SIW_OP_INVAL_STAG;
+			break;
+		case IB_WR_REG_MR:
+			sqe.opcode = SIW_OP_REG_MR;
+			break;
+		default:
+			rv = -EINVAL;
+			break;
+		}
+		if (!rv) {
+			sqe.id = wr->wr_id;
+			rv = siw_sqe_complete(qp, &sqe, 0,
+					      SIW_WC_WR_FLUSH_ERR);
+		}
 		if (rv) {
 			if (bad_wr)
 				*bad_wr = wr;
@@ -1456,7 +1492,7 @@
 
 	if (pbl->max_buf < num_sle) {
 		siw_dbg_mem(mem, "too many SGE's: %d > %d\n",
-			    mem->pbl->max_buf, num_sle);
+			    num_sle, pbl->max_buf);
 		return -ENOMEM;
 	}
 	for_each_sg(sl, slp, num_sle, i) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/ipoib/ipoib_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/ipoib/ipoib_main.c
@@ -2197,6 +2197,14 @@
 		rn->attach_mcast = ipoib_mcast_attach;
 		rn->detach_mcast = ipoib_mcast_detach;
 		rn->hca = hca;
+
+		rc = netif_set_real_num_tx_queues(dev, 1);
+		if (rc)
+			goto out;
+
+		rc = netif_set_real_num_rx_queues(dev, 1);
+		if (rc)
+			goto out;
 	}
 
 	priv->rn_ops = dev->netdev_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
@@ -531,21 +531,18 @@
 		if (test_bit(IPOIB_MCAST_FLAG_SENDONLY, &mcast->flags))
 			rec.join_state = SENDONLY_FULLMEMBER_JOIN;
 	}
-	spin_unlock_irq(&priv->lock);
 
 	multicast = ib_sa_join_multicast(&ipoib_sa_client, priv->ca, priv->port,
-					 &rec, comp_mask, GFP_KERNEL,
+					 &rec, comp_mask, GFP_ATOMIC,
 					 ipoib_mcast_join_complete, mcast);
-	spin_lock_irq(&priv->lock);
 	if (IS_ERR(multicast)) {
 		ret = PTR_ERR(multicast);
 		ipoib_warn(priv, "ib_sa_join_multicast failed, status %d\n", ret);
 		/* Requeue this join task with a backoff delay */
 		__ipoib_mcast_schedule_join_thread(priv, mcast, 1);
 		clear_bit(IPOIB_MCAST_FLAG_BUSY, &mcast->flags);
-		spin_unlock_irq(&priv->lock);
 		complete(&mcast->done);
-		spin_lock_irq(&priv->lock);
+		return ret;
 	}
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/ipoib/ipoib_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/ipoib/ipoib_netlink.c
@@ -42,6 +42,11 @@
 	[IFLA_IPOIB_UMCAST]	= { .type = NLA_U16 },
 };
 
+static unsigned int ipoib_get_max_num_queues(void)
+{
+	return min_t(unsigned int, num_possible_cpus(), 128);
+}
+
 static int ipoib_fill_info(struct sk_buff *skb, const struct net_device *dev)
 {
 	struct ipoib_dev_priv *priv = ipoib_priv(dev);
@@ -173,6 +178,8 @@
 	.changelink	= ipoib_changelink,
 	.get_size	= ipoib_get_size,
 	.fill_info	= ipoib_fill_info,
+	.get_num_rx_queues = ipoib_get_max_num_queues,
+	.get_num_tx_queues = ipoib_get_max_num_queues,
 };
 
 struct rtnl_link_ops *ipoib_get_link_ops(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/ipoib/ipoib_vlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/ipoib/ipoib_vlan.c
@@ -185,8 +185,12 @@
 
 	ppriv = ipoib_priv(pdev);
 
-	snprintf(intf_name, sizeof(intf_name), "%s.%04x",
-		 ppriv->dev->name, pkey);
+	/* If you increase IFNAMSIZ, update snprintf below
+	 * to allow longer names.
+	 */
+	BUILD_BUG_ON(IFNAMSIZ != 16);
+	snprintf(intf_name, sizeof(intf_name), "%.10s.%04x", ppriv->dev->name,
+		 pkey);
 
 	ndev = ipoib_intf_alloc(ppriv->ca, ppriv->port, intf_name);
 	if (IS_ERR(ndev)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/iser/iscsi_iser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/iser/iscsi_iser.c
@@ -584,7 +584,7 @@
 	struct Scsi_Host *shost = iscsi_session_to_shost(cls_session);
 
 	iscsi_session_teardown(cls_session);
-	iscsi_host_remove(shost);
+	iscsi_host_remove(shost, false);
 	iscsi_host_free(shost);
 }
 
@@ -702,7 +702,7 @@
 	return cls_session;
 
 remove_host:
-	iscsi_host_remove(shost);
+	iscsi_host_remove(shost, false);
 free_host:
 	iscsi_host_free(shost);
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/iser/iscsi_iser.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/iser/iscsi_iser.h
@@ -321,12 +321,10 @@
  *
  * @mr:         memory region
  * @sig_mr:     signature memory region
- * @mr_valid:   is mr valid indicator
  */
 struct iser_reg_resources {
 	struct ib_mr                     *mr;
 	struct ib_mr                     *sig_mr;
-	u8				  mr_valid:1;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/iser/iser_initiator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/iser/iser_initiator.c
@@ -602,7 +602,10 @@
 		return -EINVAL;
 	}
 
-	desc->rsc.mr_valid = 0;
+	if (desc->sig_protected)
+		desc->rsc.sig_mr->need_inval = false;
+	else
+		desc->rsc.mr->need_inval = false;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/iser/iser_memory.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/iser/iser_memory.c
@@ -250,7 +250,7 @@
 
 	iser_set_prot_checks(iser_task->sc, &sig_attrs->check_mask);
 
-	if (rsc->mr_valid)
+	if (rsc->sig_mr->need_inval)
 		iser_inv_rkey(&tx_desc->inv_wr, mr, cqe, &wr->wr);
 
 	ib_update_fast_reg_key(mr, ib_inc_rkey(mr->rkey));
@@ -274,7 +274,7 @@
 	wr->access = IB_ACCESS_LOCAL_WRITE |
 		     IB_ACCESS_REMOTE_READ |
 		     IB_ACCESS_REMOTE_WRITE;
-	rsc->mr_valid = 1;
+	rsc->sig_mr->need_inval = true;
 
 	sig_reg->sge.lkey = mr->lkey;
 	sig_reg->rkey = mr->rkey;
@@ -299,7 +299,7 @@
 	struct ib_reg_wr *wr = &tx_desc->reg_wr;
 	int n;
 
-	if (rsc->mr_valid)
+	if (rsc->mr->need_inval)
 		iser_inv_rkey(&tx_desc->inv_wr, mr, cqe, &wr->wr);
 
 	ib_update_fast_reg_key(mr, ib_inc_rkey(mr->rkey));
@@ -322,7 +322,7 @@
 		     IB_ACCESS_REMOTE_WRITE |
 		     IB_ACCESS_REMOTE_READ;
 
-	rsc->mr_valid = 1;
+	rsc->mr->need_inval = true;
 
 	reg->sge.lkey = mr->lkey;
 	reg->rkey = mr->rkey;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/iser/iser_verbs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/iser/iser_verbs.c
@@ -136,7 +136,6 @@
 			goto err_alloc_mr_integrity;
 		}
 	}
-	desc->rsc.mr_valid = 0;
 
 	return desc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/isert/ib_isert.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/isert/ib_isert.c
@@ -656,9 +656,13 @@
 isert_connect_error(struct rdma_cm_id *cma_id)
 {
 	struct isert_conn *isert_conn = cma_id->qp->qp_context;
+	struct isert_np *isert_np = cma_id->context;
 
 	ib_drain_qp(isert_conn->qp);
+
+	mutex_lock(&isert_np->mutex);
 	list_del_init(&isert_conn->node);
+	mutex_unlock(&isert_np->mutex);
 	isert_conn->cm_id = NULL;
 	isert_put_conn(isert_conn);
 
@@ -2431,6 +2435,7 @@
 {
 	struct isert_np *isert_np = np->np_context;
 	struct isert_conn *isert_conn, *n;
+	LIST_HEAD(drop_conn_list);
 
 	if (isert_np->cm_id)
 		rdma_destroy_id(isert_np->cm_id);
@@ -2450,7 +2455,7 @@
 					 node) {
 			isert_info("cleaning isert_conn %p state (%d)\n",
 				   isert_conn, isert_conn->state);
-			isert_connect_release(isert_conn);
+			list_move_tail(&isert_conn->node, &drop_conn_list);
 		}
 	}
 
@@ -2461,11 +2466,16 @@
 					 node) {
 			isert_info("cleaning isert_conn %p state (%d)\n",
 				   isert_conn, isert_conn->state);
-			isert_connect_release(isert_conn);
+			list_move_tail(&isert_conn->node, &drop_conn_list);
 		}
 	}
 	mutex_unlock(&isert_np->mutex);
 
+	list_for_each_entry_safe(isert_conn, n, &drop_conn_list, node) {
+		list_del_init(&isert_conn->node);
+		isert_connect_release(isert_conn);
+	}
+
 	np->np_context = NULL;
 	kfree(isert_np);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-clt-stats.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-clt-stats.c
@@ -13,8 +13,8 @@
 
 void rtrs_clt_update_wc_stats(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
-	struct rtrs_clt_stats *stats = sess->stats;
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
+	struct rtrs_clt_stats *stats = clt_path->stats;
 	struct rtrs_clt_stats_pcpu *s;
 	int cpu;
 
@@ -174,8 +174,8 @@
 void rtrs_clt_update_all_stats(struct rtrs_clt_io_req *req, int dir)
 {
 	struct rtrs_clt_con *con = req->con;
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
-	struct rtrs_clt_stats *stats = sess->stats;
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
+	struct rtrs_clt_stats *stats = clt_path->stats;
 	unsigned int len;
 
 	len = req->usr_len + req->data_len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-clt-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-clt-sysfs.c
@@ -16,21 +16,21 @@
 #define MIN_MAX_RECONN_ATT -1
 #define MAX_MAX_RECONN_ATT 9999
 
-static void rtrs_clt_sess_release(struct kobject *kobj)
+static void rtrs_clt_path_release(struct kobject *kobj)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
 
-	free_sess(sess);
+	free_path(clt_path);
 }
 
 static struct kobj_type ktype_sess = {
 	.sysfs_ops = &kobj_sysfs_ops,
-	.release = rtrs_clt_sess_release
+	.release = rtrs_clt_path_release
 };
 
-static void rtrs_clt_sess_stats_release(struct kobject *kobj)
+static void rtrs_clt_path_stats_release(struct kobject *kobj)
 {
 	struct rtrs_clt_stats *stats;
 
@@ -43,7 +43,7 @@
 
 static struct kobj_type ktype_stats = {
 	.sysfs_ops = &kobj_sysfs_ops,
-	.release = rtrs_clt_sess_stats_release,
+	.release = rtrs_clt_path_stats_release,
 };
 
 static ssize_t max_reconnect_attempts_show(struct device *dev,
@@ -131,7 +131,7 @@
 
 	/* distinguish "mi" and "min-latency" with length */
 	len = strnlen(buf, NAME_MAX);
-	if (buf[len - 1] == '\n')
+	if (len && buf[len - 1] == '\n')
 		len--;
 
 	if (!strncasecmp(buf, "round-robin", 11) ||
@@ -197,10 +197,10 @@
 static ssize_t rtrs_clt_state_show(struct kobject *kobj,
 				    struct kobj_attribute *attr, char *page)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
-	if (sess->state == RTRS_CLT_CONNECTED)
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
+	if (clt_path->state == RTRS_CLT_CONNECTED)
 		return sysfs_emit(page, "connected\n");
 
 	return sysfs_emit(page, "disconnected\n");
@@ -219,16 +219,16 @@
 					 struct kobj_attribute *attr,
 					 const char *buf, size_t count)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int ret;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
 	if (!sysfs_streq(buf, "1")) {
-		rtrs_err(sess->clt, "%s: unknown value: '%s'\n",
+		rtrs_err(clt_path->clt, "%s: unknown value: '%s'\n",
 			  attr->attr.name, buf);
 		return -EINVAL;
 	}
-	ret = rtrs_clt_reconnect_from_sysfs(sess);
+	ret = rtrs_clt_reconnect_from_sysfs(clt_path);
 	if (ret)
 		return ret;
 
@@ -249,15 +249,15 @@
 					  struct kobj_attribute *attr,
 					  const char *buf, size_t count)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
 	if (!sysfs_streq(buf, "1")) {
-		rtrs_err(sess->clt, "%s: unknown value: '%s'\n",
+		rtrs_err(clt_path->clt, "%s: unknown value: '%s'\n",
 			  attr->attr.name, buf);
 		return -EINVAL;
 	}
-	rtrs_clt_close_conns(sess, true);
+	rtrs_clt_close_conns(clt_path, true);
 
 	return count;
 }
@@ -276,16 +276,16 @@
 					   struct kobj_attribute *attr,
 					   const char *buf, size_t count)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int ret;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
 	if (!sysfs_streq(buf, "1")) {
-		rtrs_err(sess->clt, "%s: unknown value: '%s'\n",
+		rtrs_err(clt_path->clt, "%s: unknown value: '%s'\n",
 			  attr->attr.name, buf);
 		return -EINVAL;
 	}
-	ret = rtrs_clt_remove_path_from_sysfs(sess, &attr->attr);
+	ret = rtrs_clt_remove_path_from_sysfs(clt_path, &attr->attr);
 	if (ret)
 		return ret;
 
@@ -328,11 +328,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(kobj, typeof(*sess), kobj);
+	clt_path = container_of(kobj, typeof(*clt_path), kobj);
 
-	return sysfs_emit(page, "%u\n", sess->hca_port);
+	return sysfs_emit(page, "%u\n", clt_path->hca_port);
 }
 
 static struct kobj_attribute rtrs_clt_hca_port_attr =
@@ -342,11 +342,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
 
-	return sysfs_emit(page, "%s\n", sess->hca_name);
+	return sysfs_emit(page, "%s\n", clt_path->hca_name);
 }
 
 static struct kobj_attribute rtrs_clt_hca_name_attr =
@@ -356,12 +356,12 @@
 				    struct kobj_attribute *attr,
 				    char *page)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
 
 	return sysfs_emit(page, "%lld ns\n",
-			  ktime_to_ns(sess->s.hb_cur_latency));
+			  ktime_to_ns(clt_path->s.hb_cur_latency));
 }
 
 static struct kobj_attribute rtrs_clt_cur_latency_attr =
@@ -371,11 +371,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int len;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
-	len = sockaddr_to_str((struct sockaddr *)&sess->s.src_addr, page,
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
+	len = sockaddr_to_str((struct sockaddr *)&clt_path->s.src_addr, page,
 			      PAGE_SIZE);
 	len += sysfs_emit_at(page, len, "\n");
 	return len;
@@ -388,11 +388,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int len;
 
-	sess = container_of(kobj, struct rtrs_clt_sess, kobj);
-	len = sockaddr_to_str((struct sockaddr *)&sess->s.dst_addr, page,
+	clt_path = container_of(kobj, struct rtrs_clt_path, kobj);
+	len = sockaddr_to_str((struct sockaddr *)&clt_path->s.dst_addr, page,
 			      PAGE_SIZE);
 	len += sysfs_emit_at(page, len, "\n");
 	return len;
@@ -401,7 +401,7 @@
 static struct kobj_attribute rtrs_clt_dst_addr_attr =
 	__ATTR(dst_addr, 0444, rtrs_clt_dst_addr_show, NULL);
 
-static struct attribute *rtrs_clt_sess_attrs[] = {
+static struct attribute *rtrs_clt_path_attrs[] = {
 	&rtrs_clt_hca_name_attr.attr,
 	&rtrs_clt_hca_port_attr.attr,
 	&rtrs_clt_src_addr_attr.attr,
@@ -414,42 +414,43 @@
 	NULL,
 };
 
-static const struct attribute_group rtrs_clt_sess_attr_group = {
-	.attrs = rtrs_clt_sess_attrs,
+static const struct attribute_group rtrs_clt_path_attr_group = {
+	.attrs = rtrs_clt_path_attrs,
 };
 
-int rtrs_clt_create_sess_files(struct rtrs_clt_sess *sess)
+int rtrs_clt_create_path_files(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt *clt = clt_path->clt;
 	char str[NAME_MAX];
 	int err;
 	struct rtrs_addr path = {
-		.src = &sess->s.src_addr,
-		.dst = &sess->s.dst_addr,
+		.src = &clt_path->s.src_addr,
+		.dst = &clt_path->s.dst_addr,
 	};
 
 	rtrs_addr_to_str(&path, str, sizeof(str));
-	err = kobject_init_and_add(&sess->kobj, &ktype_sess, clt->kobj_paths,
+	err = kobject_init_and_add(&clt_path->kobj, &ktype_sess,
+				   clt->kobj_paths,
 				   "%s", str);
 	if (err) {
 		pr_err("kobject_init_and_add: %d\n", err);
-		kobject_put(&sess->kobj);
+		kobject_put(&clt_path->kobj);
 		return err;
 	}
-	err = sysfs_create_group(&sess->kobj, &rtrs_clt_sess_attr_group);
+	err = sysfs_create_group(&clt_path->kobj, &rtrs_clt_path_attr_group);
 	if (err) {
 		pr_err("sysfs_create_group(): %d\n", err);
 		goto put_kobj;
 	}
-	err = kobject_init_and_add(&sess->stats->kobj_stats, &ktype_stats,
-				   &sess->kobj, "stats");
+	err = kobject_init_and_add(&clt_path->stats->kobj_stats, &ktype_stats,
+				   &clt_path->kobj, "stats");
 	if (err) {
 		pr_err("kobject_init_and_add: %d\n", err);
-		kobject_put(&sess->stats->kobj_stats);
+		kobject_put(&clt_path->stats->kobj_stats);
 		goto remove_group;
 	}
 
-	err = sysfs_create_group(&sess->stats->kobj_stats,
+	err = sysfs_create_group(&clt_path->stats->kobj_stats,
 				 &rtrs_clt_stats_attr_group);
 	if (err) {
 		pr_err("failed to create stats sysfs group, err: %d\n", err);
@@ -459,25 +460,25 @@
 	return 0;
 
 put_kobj_stats:
-	kobject_del(&sess->stats->kobj_stats);
-	kobject_put(&sess->stats->kobj_stats);
+	kobject_del(&clt_path->stats->kobj_stats);
+	kobject_put(&clt_path->stats->kobj_stats);
 remove_group:
-	sysfs_remove_group(&sess->kobj, &rtrs_clt_sess_attr_group);
+	sysfs_remove_group(&clt_path->kobj, &rtrs_clt_path_attr_group);
 put_kobj:
-	kobject_del(&sess->kobj);
-	kobject_put(&sess->kobj);
+	kobject_del(&clt_path->kobj);
+	kobject_put(&clt_path->kobj);
 
 	return err;
 }
 
-void rtrs_clt_destroy_sess_files(struct rtrs_clt_sess *sess,
+void rtrs_clt_destroy_path_files(struct rtrs_clt_path *clt_path,
 				  const struct attribute *sysfs_self)
 {
-	kobject_del(&sess->stats->kobj_stats);
-	kobject_put(&sess->stats->kobj_stats);
+	kobject_del(&clt_path->stats->kobj_stats);
+	kobject_put(&clt_path->stats->kobj_stats);
 	if (sysfs_self)
-		sysfs_remove_file_self(&sess->kobj, sysfs_self);
-	kobject_del(&sess->kobj);
+		sysfs_remove_file_self(&clt_path->kobj, sysfs_self);
+	kobject_del(&clt_path->kobj);
 }
 
 static struct attribute *rtrs_clt_attrs[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-clt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-clt.c
@@ -48,12 +48,12 @@
 
 static inline bool rtrs_clt_is_connected(const struct rtrs_clt *clt)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	bool connected = false;
 
 	rcu_read_lock();
-	list_for_each_entry_rcu(sess, &clt->paths_list, s.entry)
-		connected |= READ_ONCE(sess->state) == RTRS_CLT_CONNECTED;
+	list_for_each_entry_rcu(clt_path, &clt->paths_list, s.entry)
+		connected |= READ_ONCE(clt_path->state) == RTRS_CLT_CONNECTED;
 	rcu_read_unlock();
 
 	return connected;
@@ -163,29 +163,29 @@
 
 /**
  * rtrs_permit_to_clt_con() - returns RDMA connection pointer by the permit
- * @sess: client session pointer
+ * @clt_path: client path pointer
  * @permit: permit for the allocation of the RDMA buffer
  * Note:
  *     IO connection starts from 1.
  *     0 connection is for user messages.
  */
 static
-struct rtrs_clt_con *rtrs_permit_to_clt_con(struct rtrs_clt_sess *sess,
+struct rtrs_clt_con *rtrs_permit_to_clt_con(struct rtrs_clt_path *clt_path,
 					    struct rtrs_permit *permit)
 {
 	int id = 0;
 
 	if (permit->con_type == RTRS_IO_CON)
-		id = (permit->cpu_id % (sess->s.irq_con_num - 1)) + 1;
+		id = (permit->cpu_id % (clt_path->s.irq_con_num - 1)) + 1;
 
-	return to_clt_con(sess->s.con[id]);
+	return to_clt_con(clt_path->s.con[id]);
 }
 
 /**
  * rtrs_clt_change_state() - change the session state through session state
  * machine.
  *
- * @sess: client session to change the state of.
+ * @clt_path: client path to change the state of.
  * @new_state: state to change to.
  *
  * returns true if sess's state is changed to new state, otherwise return false.
@@ -193,15 +193,15 @@
  * Locks:
  * state_wq lock must be hold.
  */
-static bool rtrs_clt_change_state(struct rtrs_clt_sess *sess,
+static bool rtrs_clt_change_state(struct rtrs_clt_path *clt_path,
 				     enum rtrs_clt_state new_state)
 {
 	enum rtrs_clt_state old_state;
 	bool changed = false;
 
-	lockdep_assert_held(&sess->state_wq.lock);
+	lockdep_assert_held(&clt_path->state_wq.lock);
 
-	old_state = sess->state;
+	old_state = clt_path->state;
 	switch (new_state) {
 	case RTRS_CLT_CONNECTING:
 		switch (old_state) {
@@ -275,42 +275,42 @@
 		break;
 	}
 	if (changed) {
-		sess->state = new_state;
-		wake_up_locked(&sess->state_wq);
+		clt_path->state = new_state;
+		wake_up_locked(&clt_path->state_wq);
 	}
 
 	return changed;
 }
 
-static bool rtrs_clt_change_state_from_to(struct rtrs_clt_sess *sess,
+static bool rtrs_clt_change_state_from_to(struct rtrs_clt_path *clt_path,
 					   enum rtrs_clt_state old_state,
 					   enum rtrs_clt_state new_state)
 {
 	bool changed = false;
 
-	spin_lock_irq(&sess->state_wq.lock);
-	if (sess->state == old_state)
-		changed = rtrs_clt_change_state(sess, new_state);
-	spin_unlock_irq(&sess->state_wq.lock);
+	spin_lock_irq(&clt_path->state_wq.lock);
+	if (clt_path->state == old_state)
+		changed = rtrs_clt_change_state(clt_path, new_state);
+	spin_unlock_irq(&clt_path->state_wq.lock);
 
 	return changed;
 }
 
 static void rtrs_rdma_error_recovery(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 
-	if (rtrs_clt_change_state_from_to(sess,
+	if (rtrs_clt_change_state_from_to(clt_path,
 					   RTRS_CLT_CONNECTED,
 					   RTRS_CLT_RECONNECTING)) {
-		struct rtrs_clt *clt = sess->clt;
+		struct rtrs_clt *clt = clt_path->clt;
 		unsigned int delay_ms;
 
 		/*
 		 * Normal scenario, reconnect if we were successfully connected
 		 */
 		delay_ms = clt->reconnect_delay_sec * 1000;
-		queue_delayed_work(rtrs_wq, &sess->reconnect_dwork,
+		queue_delayed_work(rtrs_wq, &clt_path->reconnect_dwork,
 				   msecs_to_jiffies(delay_ms +
 						    prandom_u32() % RTRS_RECONNECT_SEED));
 	} else {
@@ -319,7 +319,7 @@
 		 * so notify waiter with error state, waiter is responsible
 		 * for cleaning the rest and reconnect if needed.
 		 */
-		rtrs_clt_change_state_from_to(sess,
+		rtrs_clt_change_state_from_to(clt_path,
 					       RTRS_CLT_CONNECTING,
 					       RTRS_CLT_CONNECTING_ERR);
 	}
@@ -330,7 +330,7 @@
 	struct rtrs_clt_con *con = to_clt_con(wc->qp->qp_context);
 
 	if (wc->status != IB_WC_SUCCESS) {
-		rtrs_err(con->c.sess, "Failed IB_WR_REG_MR: %s\n",
+		rtrs_err(con->c.path, "Failed IB_WR_REG_MR: %s\n",
 			  ib_wc_status_msg(wc->status));
 		rtrs_rdma_error_recovery(con);
 	}
@@ -350,7 +350,7 @@
 	struct rtrs_clt_con *con = to_clt_con(wc->qp->qp_context);
 
 	if (wc->status != IB_WC_SUCCESS) {
-		rtrs_err(con->c.sess, "Failed IB_WR_LOCAL_INV: %s\n",
+		rtrs_err(con->c.path, "Failed IB_WR_LOCAL_INV: %s\n",
 			  ib_wc_status_msg(wc->status));
 		rtrs_rdma_error_recovery(con);
 	}
@@ -380,14 +380,14 @@
 			      bool notify, bool can_wait)
 {
 	struct rtrs_clt_con *con = req->con;
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int err;
 
-	if (WARN_ON(!req->in_use))
+	if (!req->in_use)
 		return;
 	if (WARN_ON(!req->con))
 		return;
-	sess = to_clt_sess(con->c.sess);
+	clt_path = to_clt_path(con->c.path);
 
 	if (req->sg_cnt) {
 		if (req->dir == DMA_FROM_DEVICE && req->need_inv) {
@@ -417,7 +417,7 @@
 			refcount_inc(&req->ref);
 			err = rtrs_inv_rkey(req);
 			if (err) {
-				rtrs_err(con->c.sess, "Send INV WR key=%#x: %d\n",
+				rtrs_err(con->c.path, "Send INV WR key=%#x: %d\n",
 					  req->mr->rkey, err);
 			} else if (can_wait) {
 				wait_for_completion(&req->inv_comp);
@@ -433,21 +433,21 @@
 			if (!refcount_dec_and_test(&req->ref))
 				return;
 		}
-		ib_dma_unmap_sg(sess->s.dev->ib_dev, req->sglist,
+		ib_dma_unmap_sg(clt_path->s.dev->ib_dev, req->sglist,
 				req->sg_cnt, req->dir);
 	}
 	if (!refcount_dec_and_test(&req->ref))
 		return;
 	if (req->mp_policy == MP_POLICY_MIN_INFLIGHT)
-		atomic_dec(&sess->stats->inflight);
+		atomic_dec(&clt_path->stats->inflight);
 
 	req->in_use = false;
 	req->con = NULL;
 
 	if (errno) {
-		rtrs_err_rl(con->c.sess, "IO request failed: error=%d path=%s [%s:%u] notify=%d\n",
-			    errno, kobject_name(&sess->kobj), sess->hca_name,
-			    sess->hca_port, notify);
+		rtrs_err_rl(con->c.path, "IO request failed: error=%d path=%s [%s:%u] notify=%d\n",
+			    errno, kobject_name(&clt_path->kobj), clt_path->hca_name,
+			    clt_path->hca_port, notify);
 	}
 
 	if (notify)
@@ -459,12 +459,12 @@
 				struct rtrs_rbuf *rbuf, u32 off,
 				u32 imm, struct ib_send_wr *wr)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	enum ib_send_flags flags;
 	struct ib_sge sge;
 
 	if (!req->sg_size) {
-		rtrs_wrn(con->c.sess,
+		rtrs_wrn(con->c.path,
 			 "Doing RDMA Write failed, no data supplied\n");
 		return -EINVAL;
 	}
@@ -472,16 +472,17 @@
 	/* user data and user message in the first list element */
 	sge.addr   = req->iu->dma_addr;
 	sge.length = req->sg_size;
-	sge.lkey   = sess->s.dev->ib_pd->local_dma_lkey;
+	sge.lkey   = clt_path->s.dev->ib_pd->local_dma_lkey;
 
 	/*
 	 * From time to time we have to post signalled sends,
 	 * or send queue will fill up and only QP reset can help.
 	 */
-	flags = atomic_inc_return(&con->c.wr_cnt) % sess->s.signal_interval ?
+	flags = atomic_inc_return(&con->c.wr_cnt) % clt_path->s.signal_interval ?
 			0 : IB_SEND_SIGNALED;
 
-	ib_dma_sync_single_for_device(sess->s.dev->ib_dev, req->iu->dma_addr,
+	ib_dma_sync_single_for_device(clt_path->s.dev->ib_dev,
+				      req->iu->dma_addr,
 				      req->sg_size, DMA_TO_DEVICE);
 
 	return rtrs_iu_post_rdma_write_imm(&con->c, req->iu, &sge, 1,
@@ -489,15 +490,15 @@
 					    imm, flags, wr, NULL);
 }
 
-static void process_io_rsp(struct rtrs_clt_sess *sess, u32 msg_id,
+static void process_io_rsp(struct rtrs_clt_path *clt_path, u32 msg_id,
 			   s16 errno, bool w_inval)
 {
 	struct rtrs_clt_io_req *req;
 
-	if (WARN_ON(msg_id >= sess->queue_depth))
+	if (WARN_ON(msg_id >= clt_path->queue_depth))
 		return;
 
-	req = &sess->reqs[msg_id];
+	req = &clt_path->reqs[msg_id];
 	/* Drop need_inv if server responded with send with invalidation */
 	req->need_inv &= !w_inval;
 	complete_rdma_req(req, errno, true, false);
@@ -507,21 +508,21 @@
 {
 	struct rtrs_iu *iu;
 	int err;
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 
-	WARN_ON((sess->flags & RTRS_MSG_NEW_RKEY_F) == 0);
+	WARN_ON((clt_path->flags & RTRS_MSG_NEW_RKEY_F) == 0);
 	iu = container_of(wc->wr_cqe, struct rtrs_iu,
 			  cqe);
 	err = rtrs_iu_post_recv(&con->c, iu);
 	if (err) {
-		rtrs_err(con->c.sess, "post iu failed %d\n", err);
+		rtrs_err(con->c.path, "post iu failed %d\n", err);
 		rtrs_rdma_error_recovery(con);
 	}
 }
 
 static void rtrs_clt_rkey_rsp_done(struct rtrs_clt_con *con, struct ib_wc *wc)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	struct rtrs_msg_rkey_rsp *msg;
 	u32 imm_type, imm_payload;
 	bool w_inval = false;
@@ -529,25 +530,26 @@
 	u32 buf_id;
 	int err;
 
-	WARN_ON((sess->flags & RTRS_MSG_NEW_RKEY_F) == 0);
+	WARN_ON((clt_path->flags & RTRS_MSG_NEW_RKEY_F) == 0);
 
 	iu = container_of(wc->wr_cqe, struct rtrs_iu, cqe);
 
 	if (wc->byte_len < sizeof(*msg)) {
-		rtrs_err(con->c.sess, "rkey response is malformed: size %d\n",
+		rtrs_err(con->c.path, "rkey response is malformed: size %d\n",
 			  wc->byte_len);
 		goto out;
 	}
-	ib_dma_sync_single_for_cpu(sess->s.dev->ib_dev, iu->dma_addr,
+	ib_dma_sync_single_for_cpu(clt_path->s.dev->ib_dev, iu->dma_addr,
 				   iu->size, DMA_FROM_DEVICE);
 	msg = iu->buf;
 	if (le16_to_cpu(msg->type) != RTRS_MSG_RKEY_RSP) {
-		rtrs_err(sess->clt, "rkey response is malformed: type %d\n",
+		rtrs_err(clt_path->clt,
+			  "rkey response is malformed: type %d\n",
 			  le16_to_cpu(msg->type));
 		goto out;
 	}
 	buf_id = le16_to_cpu(msg->buf_id);
-	if (WARN_ON(buf_id >= sess->queue_depth))
+	if (WARN_ON(buf_id >= clt_path->queue_depth))
 		goto out;
 
 	rtrs_from_imm(be32_to_cpu(wc->ex.imm_data), &imm_type, &imm_payload);
@@ -560,10 +562,10 @@
 
 		if (WARN_ON(buf_id != msg_id))
 			goto out;
-		sess->rbufs[buf_id].rkey = le32_to_cpu(msg->rkey);
-		process_io_rsp(sess, msg_id, err, w_inval);
+		clt_path->rbufs[buf_id].rkey = le32_to_cpu(msg->rkey);
+		process_io_rsp(clt_path, msg_id, err, w_inval);
 	}
-	ib_dma_sync_single_for_device(sess->s.dev->ib_dev, iu->dma_addr,
+	ib_dma_sync_single_for_device(clt_path->s.dev->ib_dev, iu->dma_addr,
 				      iu->size, DMA_FROM_DEVICE);
 	return rtrs_clt_recv_done(con, wc);
 out:
@@ -600,14 +602,14 @@
 static void rtrs_clt_rdma_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_clt_con *con = to_clt_con(wc->qp->qp_context);
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	u32 imm_type, imm_payload;
 	bool w_inval = false;
 	int err;
 
 	if (wc->status != IB_WC_SUCCESS) {
 		if (wc->status != IB_WC_WR_FLUSH_ERR) {
-			rtrs_err(sess->clt, "RDMA failed: %s\n",
+			rtrs_err(clt_path->clt, "RDMA failed: %s\n",
 				  ib_wc_status_msg(wc->status));
 			rtrs_rdma_error_recovery(con);
 		}
@@ -623,6 +625,7 @@
 		 */
 		if (WARN_ON(wc->wr_cqe->done != rtrs_clt_rdma_done))
 			return;
+		clt_path->s.hb_missed_cnt = 0;
 		rtrs_from_imm(be32_to_cpu(wc->ex.imm_data),
 			       &imm_type, &imm_payload);
 		if (imm_type == RTRS_IO_RSP_IMM ||
@@ -632,21 +635,20 @@
 			w_inval = (imm_type == RTRS_IO_RSP_W_INV_IMM);
 			rtrs_from_io_rsp_imm(imm_payload, &msg_id, &err);
 
-			process_io_rsp(sess, msg_id, err, w_inval);
+			process_io_rsp(clt_path, msg_id, err, w_inval);
 		} else if (imm_type == RTRS_HB_MSG_IMM) {
 			WARN_ON(con->c.cid);
-			rtrs_send_hb_ack(&sess->s);
-			if (sess->flags & RTRS_MSG_NEW_RKEY_F)
+			rtrs_send_hb_ack(&clt_path->s);
+			if (clt_path->flags & RTRS_MSG_NEW_RKEY_F)
 				return  rtrs_clt_recv_done(con, wc);
 		} else if (imm_type == RTRS_HB_ACK_IMM) {
 			WARN_ON(con->c.cid);
-			sess->s.hb_missed_cnt = 0;
-			sess->s.hb_cur_latency =
-				ktime_sub(ktime_get(), sess->s.hb_last_sent);
-			if (sess->flags & RTRS_MSG_NEW_RKEY_F)
+			clt_path->s.hb_cur_latency =
+				ktime_sub(ktime_get(), clt_path->s.hb_last_sent);
+			if (clt_path->flags & RTRS_MSG_NEW_RKEY_F)
 				return  rtrs_clt_recv_done(con, wc);
 		} else {
-			rtrs_wrn(con->c.sess, "Unknown IMM type %u\n",
+			rtrs_wrn(con->c.path, "Unknown IMM type %u\n",
 				  imm_type);
 		}
 		if (w_inval)
@@ -658,7 +660,7 @@
 		else
 			err = rtrs_post_recv_empty(&con->c, &io_comp_cqe);
 		if (err) {
-			rtrs_err(con->c.sess, "rtrs_post_recv_empty(): %d\n",
+			rtrs_err(con->c.path, "rtrs_post_recv_empty(): %d\n",
 				  err);
 			rtrs_rdma_error_recovery(con);
 		}
@@ -667,10 +669,11 @@
 		/*
 		 * Key invalidations from server side
 		 */
+		clt_path->s.hb_missed_cnt = 0;
 		WARN_ON(!(wc->wc_flags & IB_WC_WITH_INVALIDATE ||
 			  wc->wc_flags & IB_WC_WITH_IMM));
 		WARN_ON(wc->wr_cqe->done != rtrs_clt_rdma_done);
-		if (sess->flags & RTRS_MSG_NEW_RKEY_F) {
+		if (clt_path->flags & RTRS_MSG_NEW_RKEY_F) {
 			if (wc->wc_flags & IB_WC_WITH_INVALIDATE)
 				return  rtrs_clt_recv_done(con, wc);
 
@@ -685,7 +688,7 @@
 		break;
 
 	default:
-		rtrs_wrn(sess->clt, "Unexpected WC type: %d\n", wc->opcode);
+		rtrs_wrn(clt_path->clt, "Unexpected WC type: %d\n", wc->opcode);
 		return;
 	}
 }
@@ -693,10 +696,10 @@
 static int post_recv_io(struct rtrs_clt_con *con, size_t q_size)
 {
 	int err, i;
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 
 	for (i = 0; i < q_size; i++) {
-		if (sess->flags & RTRS_MSG_NEW_RKEY_F) {
+		if (clt_path->flags & RTRS_MSG_NEW_RKEY_F) {
 			struct rtrs_iu *iu = &con->rsp_ius[i];
 
 			err = rtrs_iu_post_recv(&con->c, iu);
@@ -710,16 +713,16 @@
 	return 0;
 }
 
-static int post_recv_sess(struct rtrs_clt_sess *sess)
+static int post_recv_path(struct rtrs_clt_path *clt_path)
 {
 	size_t q_size = 0;
 	int err, cid;
 
-	for (cid = 0; cid < sess->s.con_num; cid++) {
+	for (cid = 0; cid < clt_path->s.con_num; cid++) {
 		if (cid == 0)
 			q_size = SERVICE_CON_QUEUE_DEPTH;
 		else
-			q_size = sess->queue_depth;
+			q_size = clt_path->queue_depth;
 
 		/*
 		 * x2 for RDMA read responses + FR key invalidations,
@@ -727,9 +730,10 @@
 		 */
 		q_size *= 2;
 
-		err = post_recv_io(to_clt_con(sess->s.con[cid]), q_size);
+		err = post_recv_io(to_clt_con(clt_path->s.con[cid]), q_size);
 		if (err) {
-			rtrs_err(sess->clt, "post_recv_io(), err: %d\n", err);
+			rtrs_err(clt_path->clt, "post_recv_io(), err: %d\n",
+				 err);
 			return err;
 		}
 	}
@@ -741,28 +745,28 @@
 	int i;
 	struct list_head skip_list;
 	struct rtrs_clt *clt;
-	struct rtrs_clt_sess *(*next_path)(struct path_it *it);
+	struct rtrs_clt_path *(*next_path)(struct path_it *it);
 };
 
-/**
- * list_next_or_null_rr_rcu - get next list element in round-robin fashion.
+/*
+ * rtrs_clt_get_next_path_or_null - get clt path from the list or return NULL
  * @head:	the head for the list.
- * @ptr:        the list head to take the next element from.
- * @type:       the type of the struct this is embedded in.
- * @memb:       the name of the list_head within the struct.
+ * @clt_path:	The element to take the next clt_path from.
  *
- * Next element returned in round-robin fashion, i.e. head will be skipped,
+ * Next clt path returned in round-robin fashion, i.e. head will be skipped,
  * but if list is observed as empty, NULL will be returned.
  *
- * This primitive may safely run concurrently with the _rcu list-mutation
+ * This function may safely run concurrently with the _rcu list-mutation
  * primitives such as list_add_rcu() as long as it's guarded by rcu_read_lock().
  */
-#define list_next_or_null_rr_rcu(head, ptr, type, memb) \
-({ \
-	list_next_or_null_rcu(head, ptr, type, memb) ?: \
-		list_next_or_null_rcu(head, READ_ONCE((ptr)->next), \
-				      type, memb); \
-})
+static inline struct rtrs_clt_path *
+rtrs_clt_get_next_path_or_null(struct list_head *head, struct rtrs_clt_path *clt_path)
+{
+	return list_next_or_null_rcu(head, &clt_path->s.entry, typeof(*clt_path), s.entry) ?:
+				     list_next_or_null_rcu(head,
+							   READ_ONCE((&clt_path->s.entry)->next),
+							   typeof(*clt_path), s.entry);
+}
 
 /**
  * get_next_path_rr() - Returns path in round-robin fashion.
@@ -773,10 +777,10 @@
  * Locks:
  *    rcu_read_lock() must be hold.
  */
-static struct rtrs_clt_sess *get_next_path_rr(struct path_it *it)
+static struct rtrs_clt_path *get_next_path_rr(struct path_it *it)
 {
-	struct rtrs_clt_sess __rcu **ppcpu_path;
-	struct rtrs_clt_sess *path;
+	struct rtrs_clt_path __rcu **ppcpu_path;
+	struct rtrs_clt_path *path;
 	struct rtrs_clt *clt;
 
 	clt = it->clt;
@@ -793,10 +797,8 @@
 		path = list_first_or_null_rcu(&clt->paths_list,
 					      typeof(*path), s.entry);
 	else
-		path = list_next_or_null_rr_rcu(&clt->paths_list,
-						&path->s.entry,
-						typeof(*path),
-						s.entry);
+		path = rtrs_clt_get_next_path_or_null(&clt->paths_list, path);
+
 	rcu_assign_pointer(*ppcpu_path, path);
 
 	return path;
@@ -811,26 +813,26 @@
  * Locks:
  *    rcu_read_lock() must be hold.
  */
-static struct rtrs_clt_sess *get_next_path_min_inflight(struct path_it *it)
+static struct rtrs_clt_path *get_next_path_min_inflight(struct path_it *it)
 {
-	struct rtrs_clt_sess *min_path = NULL;
+	struct rtrs_clt_path *min_path = NULL;
 	struct rtrs_clt *clt = it->clt;
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int min_inflight = INT_MAX;
 	int inflight;
 
-	list_for_each_entry_rcu(sess, &clt->paths_list, s.entry) {
-		if (READ_ONCE(sess->state) != RTRS_CLT_CONNECTED)
+	list_for_each_entry_rcu(clt_path, &clt->paths_list, s.entry) {
+		if (READ_ONCE(clt_path->state) != RTRS_CLT_CONNECTED)
 			continue;
 
-		if (!list_empty(raw_cpu_ptr(sess->mp_skip_entry)))
+		if (!list_empty(raw_cpu_ptr(clt_path->mp_skip_entry)))
 			continue;
 
-		inflight = atomic_read(&sess->stats->inflight);
+		inflight = atomic_read(&clt_path->stats->inflight);
 
 		if (inflight < min_inflight) {
 			min_inflight = inflight;
-			min_path = sess;
+			min_path = clt_path;
 		}
 	}
 
@@ -862,26 +864,26 @@
  * Therefore the caller MUST check the returned
  * path is NULL and trigger the IO error.
  */
-static struct rtrs_clt_sess *get_next_path_min_latency(struct path_it *it)
+static struct rtrs_clt_path *get_next_path_min_latency(struct path_it *it)
 {
-	struct rtrs_clt_sess *min_path = NULL;
+	struct rtrs_clt_path *min_path = NULL;
 	struct rtrs_clt *clt = it->clt;
-	struct rtrs_clt_sess *sess;
-	ktime_t min_latency = INT_MAX;
+	struct rtrs_clt_path *clt_path;
+	ktime_t min_latency = KTIME_MAX;
 	ktime_t latency;
 
-	list_for_each_entry_rcu(sess, &clt->paths_list, s.entry) {
-		if (READ_ONCE(sess->state) != RTRS_CLT_CONNECTED)
+	list_for_each_entry_rcu(clt_path, &clt->paths_list, s.entry) {
+		if (READ_ONCE(clt_path->state) != RTRS_CLT_CONNECTED)
 			continue;
 
-		if (!list_empty(raw_cpu_ptr(sess->mp_skip_entry)))
+		if (!list_empty(raw_cpu_ptr(clt_path->mp_skip_entry)))
 			continue;
 
-		latency = sess->s.hb_cur_latency;
+		latency = clt_path->s.hb_cur_latency;
 
 		if (latency < min_latency) {
 			min_latency = latency;
-			min_path = sess;
+			min_path = clt_path;
 		}
 	}
 
@@ -928,7 +930,7 @@
  * the corresponding buffer of rtrs_iu (req->iu->buf), which later on will
  * also hold the control message of rtrs.
  * @req: an io request holding information about IO.
- * @sess: client session
+ * @clt_path: client path
  * @conf: conformation callback function to notify upper layer.
  * @permit: permit for allocation of RDMA remote buffer
  * @priv: private pointer
@@ -940,7 +942,7 @@
  * @dir: direction of the IO.
  */
 static void rtrs_clt_init_req(struct rtrs_clt_io_req *req,
-			      struct rtrs_clt_sess *sess,
+			      struct rtrs_clt_path *clt_path,
 			      void (*conf)(void *priv, int errno),
 			      struct rtrs_permit *permit, void *priv,
 			      const struct kvec *vec, size_t usr_len,
@@ -958,15 +960,15 @@
 	req->sg_cnt = sg_cnt;
 	req->priv = priv;
 	req->dir = dir;
-	req->con = rtrs_permit_to_clt_con(sess, permit);
+	req->con = rtrs_permit_to_clt_con(clt_path, permit);
 	req->conf = conf;
 	req->need_inv = false;
 	req->need_inv_comp = false;
 	req->inv_errno = 0;
 	refcount_set(&req->ref, 1);
-	req->mp_policy = sess->clt->mp_policy;
+	req->mp_policy = clt_path->clt->mp_policy;
 
-	iov_iter_kvec(&iter, READ, vec, 1, usr_len);
+	iov_iter_kvec(&iter, WRITE, vec, 1, usr_len);
 	len = _copy_from_iter(req->iu->buf, usr_len, &iter);
 	WARN_ON(len != usr_len);
 
@@ -974,7 +976,7 @@
 }
 
 static struct rtrs_clt_io_req *
-rtrs_clt_get_req(struct rtrs_clt_sess *sess,
+rtrs_clt_get_req(struct rtrs_clt_path *clt_path,
 		 void (*conf)(void *priv, int errno),
 		 struct rtrs_permit *permit, void *priv,
 		 const struct kvec *vec, size_t usr_len,
@@ -983,14 +985,14 @@
 {
 	struct rtrs_clt_io_req *req;
 
-	req = &sess->reqs[permit->mem_id];
-	rtrs_clt_init_req(req, sess, conf, permit, priv, vec, usr_len,
+	req = &clt_path->reqs[permit->mem_id];
+	rtrs_clt_init_req(req, clt_path, conf, permit, priv, vec, usr_len,
 			   sg, sg_cnt, data_len, dir);
 	return req;
 }
 
 static struct rtrs_clt_io_req *
-rtrs_clt_get_copy_req(struct rtrs_clt_sess *alive_sess,
+rtrs_clt_get_copy_req(struct rtrs_clt_path *alive_path,
 		       struct rtrs_clt_io_req *fail_req)
 {
 	struct rtrs_clt_io_req *req;
@@ -999,8 +1001,8 @@
 		.iov_len  = fail_req->usr_len
 	};
 
-	req = &alive_sess->reqs[fail_req->permit->mem_id];
-	rtrs_clt_init_req(req, alive_sess, fail_req->conf, fail_req->permit,
+	req = &alive_path->reqs[fail_req->permit->mem_id];
+	rtrs_clt_init_req(req, alive_path, fail_req->conf, fail_req->permit,
 			   fail_req->priv, &vec, fail_req->usr_len,
 			   fail_req->sglist, fail_req->sg_cnt,
 			   fail_req->data_len, fail_req->dir);
@@ -1010,10 +1012,11 @@
 static int rtrs_post_rdma_write_sg(struct rtrs_clt_con *con,
 				   struct rtrs_clt_io_req *req,
 				   struct rtrs_rbuf *rbuf, bool fr_en,
-				   u32 size, u32 imm, struct ib_send_wr *wr,
+				   u32 count, u32 size, u32 imm,
+				   struct ib_send_wr *wr,
 				   struct ib_send_wr *tail)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	struct ib_sge *sge = req->sge;
 	enum ib_send_flags flags;
 	struct scatterlist *sg;
@@ -1030,25 +1033,26 @@
 		num_sge = 2;
 		ptail = tail;
 	} else {
-		for_each_sg(req->sglist, sg, req->sg_cnt, i) {
+		for_each_sg(req->sglist, sg, count, i) {
 			sge[i].addr   = sg_dma_address(sg);
 			sge[i].length = sg_dma_len(sg);
-			sge[i].lkey   = sess->s.dev->ib_pd->local_dma_lkey;
+			sge[i].lkey   = clt_path->s.dev->ib_pd->local_dma_lkey;
 		}
-		num_sge = 1 + req->sg_cnt;
+		num_sge = 1 + count;
 	}
 	sge[i].addr   = req->iu->dma_addr;
 	sge[i].length = size;
-	sge[i].lkey   = sess->s.dev->ib_pd->local_dma_lkey;
+	sge[i].lkey   = clt_path->s.dev->ib_pd->local_dma_lkey;
 
 	/*
 	 * From time to time we have to post signalled sends,
 	 * or send queue will fill up and only QP reset can help.
 	 */
-	flags = atomic_inc_return(&con->c.wr_cnt) % sess->s.signal_interval ?
+	flags = atomic_inc_return(&con->c.wr_cnt) % clt_path->s.signal_interval ?
 			0 : IB_SEND_SIGNALED;
 
-	ib_dma_sync_single_for_device(sess->s.dev->ib_dev, req->iu->dma_addr,
+	ib_dma_sync_single_for_device(clt_path->s.dev->ib_dev,
+				      req->iu->dma_addr,
 				      size, DMA_TO_DEVICE);
 
 	return rtrs_iu_post_rdma_write_imm(&con->c, req->iu, sge, num_sge,
@@ -1074,8 +1078,8 @@
 static int rtrs_clt_write_req(struct rtrs_clt_io_req *req)
 {
 	struct rtrs_clt_con *con = req->con;
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_clt_sess *sess = to_clt_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_clt_path *clt_path = to_clt_path(s);
 	struct rtrs_msg_rdma_write *msg;
 
 	struct rtrs_rbuf *rbuf;
@@ -1088,13 +1092,13 @@
 
 	const size_t tsize = sizeof(*msg) + req->data_len + req->usr_len;
 
-	if (tsize > sess->chunk_size) {
+	if (tsize > clt_path->chunk_size) {
 		rtrs_wrn(s, "Write request failed, size too big %zu > %d\n",
-			  tsize, sess->chunk_size);
+			  tsize, clt_path->chunk_size);
 		return -EMSGSIZE;
 	}
 	if (req->sg_cnt) {
-		count = ib_dma_map_sg(sess->s.dev->ib_dev, req->sglist,
+		count = ib_dma_map_sg(clt_path->s.dev->ib_dev, req->sglist,
 				      req->sg_cnt, req->dir);
 		if (!count) {
 			rtrs_wrn(s, "Write request failed, map failed\n");
@@ -1111,7 +1115,7 @@
 	imm = rtrs_to_io_req_imm(imm);
 	buf_id = req->permit->mem_id;
 	req->sg_size = tsize;
-	rbuf = &sess->rbufs[buf_id];
+	rbuf = &clt_path->rbufs[buf_id];
 
 	if (count) {
 		ret = rtrs_map_sg_fr(req, count);
@@ -1119,7 +1123,7 @@
 			rtrs_err_rl(s,
 				    "Write request failed, failed to map fast reg. data, err: %d\n",
 				    ret);
-			ib_dma_unmap_sg(sess->s.dev->ib_dev, req->sglist,
+			ib_dma_unmap_sg(clt_path->s.dev->ib_dev, req->sglist,
 					req->sg_cnt, req->dir);
 			return ret;
 		}
@@ -1147,18 +1151,18 @@
 	 */
 	rtrs_clt_update_all_stats(req, WRITE);
 
-	ret = rtrs_post_rdma_write_sg(req->con, req, rbuf, fr_en,
+	ret = rtrs_post_rdma_write_sg(req->con, req, rbuf, fr_en, count,
 				      req->usr_len + sizeof(*msg),
 				      imm, wr, &inv_wr);
 	if (ret) {
 		rtrs_err_rl(s,
 			    "Write request failed: error=%d path=%s [%s:%u]\n",
-			    ret, kobject_name(&sess->kobj), sess->hca_name,
-			    sess->hca_port);
+			    ret, kobject_name(&clt_path->kobj), clt_path->hca_name,
+			    clt_path->hca_port);
 		if (req->mp_policy == MP_POLICY_MIN_INFLIGHT)
-			atomic_dec(&sess->stats->inflight);
+			atomic_dec(&clt_path->stats->inflight);
 		if (req->sg_cnt)
-			ib_dma_unmap_sg(sess->s.dev->ib_dev, req->sglist,
+			ib_dma_unmap_sg(clt_path->s.dev->ib_dev, req->sglist,
 					req->sg_cnt, req->dir);
 	}
 
@@ -1168,10 +1172,10 @@
 static int rtrs_clt_read_req(struct rtrs_clt_io_req *req)
 {
 	struct rtrs_clt_con *con = req->con;
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_clt_sess *sess = to_clt_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_clt_path *clt_path = to_clt_path(s);
 	struct rtrs_msg_rdma_read *msg;
-	struct rtrs_ib_dev *dev = sess->s.dev;
+	struct rtrs_ib_dev *dev = clt_path->s.dev;
 
 	struct ib_reg_wr rwr;
 	struct ib_send_wr *wr = NULL;
@@ -1181,10 +1185,10 @@
 
 	const size_t tsize = sizeof(*msg) + req->data_len + req->usr_len;
 
-	if (tsize > sess->chunk_size) {
+	if (tsize > clt_path->chunk_size) {
 		rtrs_wrn(s,
 			  "Read request failed, message size is %zu, bigger than CHUNK_SIZE %d\n",
-			  tsize, sess->chunk_size);
+			  tsize, clt_path->chunk_size);
 		return -EMSGSIZE;
 	}
 
@@ -1254,15 +1258,15 @@
 	 */
 	rtrs_clt_update_all_stats(req, READ);
 
-	ret = rtrs_post_send_rdma(req->con, req, &sess->rbufs[buf_id],
+	ret = rtrs_post_send_rdma(req->con, req, &clt_path->rbufs[buf_id],
 				   req->data_len, imm, wr);
 	if (ret) {
 		rtrs_err_rl(s,
 			    "Read request failed: error=%d path=%s [%s:%u]\n",
-			    ret, kobject_name(&sess->kobj), sess->hca_name,
-			    sess->hca_port);
+			    ret, kobject_name(&clt_path->kobj), clt_path->hca_name,
+			    clt_path->hca_port);
 		if (req->mp_policy == MP_POLICY_MIN_INFLIGHT)
-			atomic_dec(&sess->stats->inflight);
+			atomic_dec(&clt_path->stats->inflight);
 		req->need_inv = false;
 		if (req->sg_cnt)
 			ib_dma_unmap_sg(dev->ib_dev, req->sglist,
@@ -1280,18 +1284,18 @@
 static int rtrs_clt_failover_req(struct rtrs_clt *clt,
 				 struct rtrs_clt_io_req *fail_req)
 {
-	struct rtrs_clt_sess *alive_sess;
+	struct rtrs_clt_path *alive_path;
 	struct rtrs_clt_io_req *req;
 	int err = -ECONNABORTED;
 	struct path_it it;
 
 	rcu_read_lock();
 	for (path_it_init(&it, clt);
-	     (alive_sess = it.next_path(&it)) && it.i < it.clt->paths_num;
+	     (alive_path = it.next_path(&it)) && it.i < it.clt->paths_num;
 	     it.i++) {
-		if (READ_ONCE(alive_sess->state) != RTRS_CLT_CONNECTED)
+		if (READ_ONCE(alive_path->state) != RTRS_CLT_CONNECTED)
 			continue;
-		req = rtrs_clt_get_copy_req(alive_sess, fail_req);
+		req = rtrs_clt_get_copy_req(alive_path, fail_req);
 		if (req->dir == DMA_TO_DEVICE)
 			err = rtrs_clt_write_req(req);
 		else
@@ -1301,7 +1305,7 @@
 			continue;
 		}
 		/* Success path */
-		rtrs_clt_inc_failover_cnt(alive_sess->stats);
+		rtrs_clt_inc_failover_cnt(alive_path->stats);
 		break;
 	}
 	path_it_deinit(&it);
@@ -1310,16 +1314,16 @@
 	return err;
 }
 
-static void fail_all_outstanding_reqs(struct rtrs_clt_sess *sess)
+static void fail_all_outstanding_reqs(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt *clt = clt_path->clt;
 	struct rtrs_clt_io_req *req;
 	int i, err;
 
-	if (!sess->reqs)
+	if (!clt_path->reqs)
 		return;
-	for (i = 0; i < sess->queue_depth; ++i) {
-		req = &sess->reqs[i];
+	for (i = 0; i < clt_path->queue_depth; ++i) {
+		req = &clt_path->reqs[i];
 		if (!req->in_use)
 			continue;
 
@@ -1337,38 +1341,39 @@
 	}
 }
 
-static void free_sess_reqs(struct rtrs_clt_sess *sess)
+static void free_path_reqs(struct rtrs_clt_path *clt_path)
 {
 	struct rtrs_clt_io_req *req;
 	int i;
 
-	if (!sess->reqs)
+	if (!clt_path->reqs)
 		return;
-	for (i = 0; i < sess->queue_depth; ++i) {
-		req = &sess->reqs[i];
+	for (i = 0; i < clt_path->queue_depth; ++i) {
+		req = &clt_path->reqs[i];
 		if (req->mr)
 			ib_dereg_mr(req->mr);
 		kfree(req->sge);
-		rtrs_iu_free(req->iu, sess->s.dev->ib_dev, 1);
+		rtrs_iu_free(req->iu, clt_path->s.dev->ib_dev, 1);
 	}
-	kfree(sess->reqs);
-	sess->reqs = NULL;
+	kfree(clt_path->reqs);
+	clt_path->reqs = NULL;
 }
 
-static int alloc_sess_reqs(struct rtrs_clt_sess *sess)
+static int alloc_path_reqs(struct rtrs_clt_path *clt_path)
 {
 	struct rtrs_clt_io_req *req;
 	int i, err = -ENOMEM;
 
-	sess->reqs = kcalloc(sess->queue_depth, sizeof(*sess->reqs),
-			     GFP_KERNEL);
-	if (!sess->reqs)
+	clt_path->reqs = kcalloc(clt_path->queue_depth,
+				 sizeof(*clt_path->reqs),
+				 GFP_KERNEL);
+	if (!clt_path->reqs)
 		return -ENOMEM;
 
-	for (i = 0; i < sess->queue_depth; ++i) {
-		req = &sess->reqs[i];
-		req->iu = rtrs_iu_alloc(1, sess->max_hdr_size, GFP_KERNEL,
-					 sess->s.dev->ib_dev,
+	for (i = 0; i < clt_path->queue_depth; ++i) {
+		req = &clt_path->reqs[i];
+		req->iu = rtrs_iu_alloc(1, clt_path->max_hdr_size, GFP_KERNEL,
+					 clt_path->s.dev->ib_dev,
 					 DMA_TO_DEVICE,
 					 rtrs_clt_rdma_done);
 		if (!req->iu)
@@ -1378,13 +1383,14 @@
 		if (!req->sge)
 			goto out;
 
-		req->mr = ib_alloc_mr(sess->s.dev->ib_pd, IB_MR_TYPE_MEM_REG,
-				      sess->max_pages_per_mr);
+		req->mr = ib_alloc_mr(clt_path->s.dev->ib_pd,
+				      IB_MR_TYPE_MEM_REG,
+				      clt_path->max_pages_per_mr);
 		if (IS_ERR(req->mr)) {
 			err = PTR_ERR(req->mr);
 			req->mr = NULL;
-			pr_err("Failed to alloc sess->max_pages_per_mr %d\n",
-			       sess->max_pages_per_mr);
+			pr_err("Failed to alloc clt_path->max_pages_per_mr %d\n",
+			       clt_path->max_pages_per_mr);
 			goto out;
 		}
 
@@ -1394,7 +1400,7 @@
 	return 0;
 
 out:
-	free_sess_reqs(sess);
+	free_path_reqs(clt_path);
 
 	return err;
 }
@@ -1447,13 +1453,13 @@
 	clt->permits = NULL;
 }
 
-static void query_fast_reg_mode(struct rtrs_clt_sess *sess)
+static void query_fast_reg_mode(struct rtrs_clt_path *clt_path)
 {
 	struct ib_device *ib_dev;
 	u64 max_pages_per_mr;
 	int mr_page_shift;
 
-	ib_dev = sess->s.dev->ib_dev;
+	ib_dev = clt_path->s.dev->ib_dev;
 
 	/*
 	 * Use the smallest page size supported by the HCA, down to a
@@ -1463,24 +1469,24 @@
 	mr_page_shift      = max(12, ffs(ib_dev->attrs.page_size_cap) - 1);
 	max_pages_per_mr   = ib_dev->attrs.max_mr_size;
 	do_div(max_pages_per_mr, (1ull << mr_page_shift));
-	sess->max_pages_per_mr =
-		min3(sess->max_pages_per_mr, (u32)max_pages_per_mr,
+	clt_path->max_pages_per_mr =
+		min3(clt_path->max_pages_per_mr, (u32)max_pages_per_mr,
 		     ib_dev->attrs.max_fast_reg_page_list_len);
-	sess->clt->max_segments =
-		min(sess->max_pages_per_mr, sess->clt->max_segments);
+	clt_path->clt->max_segments =
+		min(clt_path->max_pages_per_mr, clt_path->clt->max_segments);
 }
 
-static bool rtrs_clt_change_state_get_old(struct rtrs_clt_sess *sess,
+static bool rtrs_clt_change_state_get_old(struct rtrs_clt_path *clt_path,
 					   enum rtrs_clt_state new_state,
 					   enum rtrs_clt_state *old_state)
 {
 	bool changed;
 
-	spin_lock_irq(&sess->state_wq.lock);
+	spin_lock_irq(&clt_path->state_wq.lock);
 	if (old_state)
-		*old_state = sess->state;
-	changed = rtrs_clt_change_state(sess, new_state);
-	spin_unlock_irq(&sess->state_wq.lock);
+		*old_state = clt_path->state;
+	changed = rtrs_clt_change_state(clt_path, new_state);
+	spin_unlock_irq(&clt_path->state_wq.lock);
 
 	return changed;
 }
@@ -1492,9 +1498,9 @@
 	rtrs_rdma_error_recovery(con);
 }
 
-static void rtrs_clt_init_hb(struct rtrs_clt_sess *sess)
+static void rtrs_clt_init_hb(struct rtrs_clt_path *clt_path)
 {
-	rtrs_init_hb(&sess->s, &io_comp_cqe,
+	rtrs_init_hb(&clt_path->s, &io_comp_cqe,
 		      RTRS_HB_INTERVAL_MS,
 		      RTRS_HB_MISSED_MAX,
 		      rtrs_clt_hb_err_handler,
@@ -1504,17 +1510,17 @@
 static void rtrs_clt_reconnect_work(struct work_struct *work);
 static void rtrs_clt_close_work(struct work_struct *work);
 
-static struct rtrs_clt_sess *alloc_sess(struct rtrs_clt *clt,
+static struct rtrs_clt_path *alloc_path(struct rtrs_clt *clt,
 					const struct rtrs_addr *path,
 					size_t con_num, u32 nr_poll_queues)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int err = -ENOMEM;
 	int cpu;
 	size_t total_con;
 
-	sess = kzalloc(sizeof(*sess), GFP_KERNEL);
-	if (!sess)
+	clt_path = kzalloc(sizeof(*clt_path), GFP_KERNEL);
+	if (!clt_path)
 		goto err;
 
 	/*
@@ -1522,20 +1528,21 @@
 	 * +1: Extra connection for user messages
 	 */
 	total_con = con_num + nr_poll_queues + 1;
-	sess->s.con = kcalloc(total_con, sizeof(*sess->s.con), GFP_KERNEL);
-	if (!sess->s.con)
-		goto err_free_sess;
+	clt_path->s.con = kcalloc(total_con, sizeof(*clt_path->s.con),
+				  GFP_KERNEL);
+	if (!clt_path->s.con)
+		goto err_free_path;
 
-	sess->s.con_num = total_con;
-	sess->s.irq_con_num = con_num + 1;
+	clt_path->s.con_num = total_con;
+	clt_path->s.irq_con_num = con_num + 1;
 
-	sess->stats = kzalloc(sizeof(*sess->stats), GFP_KERNEL);
-	if (!sess->stats)
+	clt_path->stats = kzalloc(sizeof(*clt_path->stats), GFP_KERNEL);
+	if (!clt_path->stats)
 		goto err_free_con;
 
-	mutex_init(&sess->init_mutex);
-	uuid_gen(&sess->s.uuid);
-	memcpy(&sess->s.dst_addr, path->dst,
+	mutex_init(&clt_path->init_mutex);
+	uuid_gen(&clt_path->s.uuid);
+	memcpy(&clt_path->s.dst_addr, path->dst,
 	       rdma_addr_size((struct sockaddr *)path->dst));
 
 	/*
@@ -1544,53 +1551,54 @@
 	 * the sess->src_addr will contain only zeros, which is then fine.
 	 */
 	if (path->src)
-		memcpy(&sess->s.src_addr, path->src,
+		memcpy(&clt_path->s.src_addr, path->src,
 		       rdma_addr_size((struct sockaddr *)path->src));
-	strscpy(sess->s.sessname, clt->sessname, sizeof(sess->s.sessname));
-	sess->clt = clt;
-	sess->max_pages_per_mr = RTRS_MAX_SEGMENTS;
-	init_waitqueue_head(&sess->state_wq);
-	sess->state = RTRS_CLT_CONNECTING;
-	atomic_set(&sess->connected_cnt, 0);
-	INIT_WORK(&sess->close_work, rtrs_clt_close_work);
-	INIT_DELAYED_WORK(&sess->reconnect_dwork, rtrs_clt_reconnect_work);
-	rtrs_clt_init_hb(sess);
+	strscpy(clt_path->s.sessname, clt->sessname,
+		sizeof(clt_path->s.sessname));
+	clt_path->clt = clt;
+	clt_path->max_pages_per_mr = RTRS_MAX_SEGMENTS;
+	init_waitqueue_head(&clt_path->state_wq);
+	clt_path->state = RTRS_CLT_CONNECTING;
+	atomic_set(&clt_path->connected_cnt, 0);
+	INIT_WORK(&clt_path->close_work, rtrs_clt_close_work);
+	INIT_DELAYED_WORK(&clt_path->reconnect_dwork, rtrs_clt_reconnect_work);
+	rtrs_clt_init_hb(clt_path);
 
-	sess->mp_skip_entry = alloc_percpu(typeof(*sess->mp_skip_entry));
-	if (!sess->mp_skip_entry)
+	clt_path->mp_skip_entry = alloc_percpu(typeof(*clt_path->mp_skip_entry));
+	if (!clt_path->mp_skip_entry)
 		goto err_free_stats;
 
 	for_each_possible_cpu(cpu)
-		INIT_LIST_HEAD(per_cpu_ptr(sess->mp_skip_entry, cpu));
+		INIT_LIST_HEAD(per_cpu_ptr(clt_path->mp_skip_entry, cpu));
 
-	err = rtrs_clt_init_stats(sess->stats);
+	err = rtrs_clt_init_stats(clt_path->stats);
 	if (err)
 		goto err_free_percpu;
 
-	return sess;
+	return clt_path;
 
 err_free_percpu:
-	free_percpu(sess->mp_skip_entry);
+	free_percpu(clt_path->mp_skip_entry);
 err_free_stats:
-	kfree(sess->stats);
+	kfree(clt_path->stats);
 err_free_con:
-	kfree(sess->s.con);
-err_free_sess:
-	kfree(sess);
+	kfree(clt_path->s.con);
+err_free_path:
+	kfree(clt_path);
 err:
 	return ERR_PTR(err);
 }
 
-void free_sess(struct rtrs_clt_sess *sess)
+void free_path(struct rtrs_clt_path *clt_path)
 {
-	free_percpu(sess->mp_skip_entry);
-	mutex_destroy(&sess->init_mutex);
-	kfree(sess->s.con);
-	kfree(sess->rbufs);
-	kfree(sess);
+	free_percpu(clt_path->mp_skip_entry);
+	mutex_destroy(&clt_path->init_mutex);
+	kfree(clt_path->s.con);
+	kfree(clt_path->rbufs);
+	kfree(clt_path);
 }
 
-static int create_con(struct rtrs_clt_sess *sess, unsigned int cid)
+static int create_con(struct rtrs_clt_path *clt_path, unsigned int cid)
 {
 	struct rtrs_clt_con *con;
 
@@ -1601,28 +1609,28 @@
 	/* Map first two connections to the first CPU */
 	con->cpu  = (cid ? cid - 1 : 0) % nr_cpu_ids;
 	con->c.cid = cid;
-	con->c.sess = &sess->s;
+	con->c.path = &clt_path->s;
 	/* Align with srv, init as 1 */
 	atomic_set(&con->c.wr_cnt, 1);
 	mutex_init(&con->con_mutex);
 
-	sess->s.con[cid] = &con->c;
+	clt_path->s.con[cid] = &con->c;
 
 	return 0;
 }
 
 static void destroy_con(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 
-	sess->s.con[con->c.cid] = NULL;
+	clt_path->s.con[con->c.cid] = NULL;
 	mutex_destroy(&con->con_mutex);
 	kfree(con);
 }
 
 static int create_con_cq_qp(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	u32 max_send_wr, max_recv_wr, cq_num, max_send_sge, wr_limit;
 	int err, cq_vector;
 	struct rtrs_msg_rkey_rsp *rsp;
@@ -1631,7 +1639,7 @@
 	if (con->c.cid == 0) {
 		max_send_sge = 1;
 		/* We must be the first here */
-		if (WARN_ON(sess->s.dev))
+		if (WARN_ON(clt_path->s.dev))
 			return -EINVAL;
 
 		/*
@@ -1639,16 +1647,16 @@
 		 * Be careful not to close user connection before ib dev
 		 * is gracefully put.
 		 */
-		sess->s.dev = rtrs_ib_dev_find_or_add(con->c.cm_id->device,
+		clt_path->s.dev = rtrs_ib_dev_find_or_add(con->c.cm_id->device,
 						       &dev_pd);
-		if (!sess->s.dev) {
-			rtrs_wrn(sess->clt,
+		if (!clt_path->s.dev) {
+			rtrs_wrn(clt_path->clt,
 				  "rtrs_ib_dev_find_get_or_add(): no memory\n");
 			return -ENOMEM;
 		}
-		sess->s.dev_ref = 1;
-		query_fast_reg_mode(sess);
-		wr_limit = sess->s.dev->ib_dev->attrs.max_qp_wr;
+		clt_path->s.dev_ref = 1;
+		query_fast_reg_mode(clt_path);
+		wr_limit = clt_path->s.dev->ib_dev->attrs.max_qp_wr;
 		/*
 		 * Two (request + registration) completion for send
 		 * Two for recv if always_invalidate is set on server
@@ -1665,27 +1673,28 @@
 		 * This is always true if user connection (cid == 0) is
 		 * established first.
 		 */
-		if (WARN_ON(!sess->s.dev))
+		if (WARN_ON(!clt_path->s.dev))
 			return -EINVAL;
-		if (WARN_ON(!sess->queue_depth))
+		if (WARN_ON(!clt_path->queue_depth))
 			return -EINVAL;
 
-		wr_limit = sess->s.dev->ib_dev->attrs.max_qp_wr;
+		wr_limit = clt_path->s.dev->ib_dev->attrs.max_qp_wr;
 		/* Shared between connections */
-		sess->s.dev_ref++;
+		clt_path->s.dev_ref++;
 		max_send_wr = min_t(int, wr_limit,
 			      /* QD * (REQ + RSP + FR REGS or INVS) + drain */
-			      sess->queue_depth * 3 + 1);
+			      clt_path->queue_depth * 4 + 1);
 		max_recv_wr = min_t(int, wr_limit,
-			      sess->queue_depth * 3 + 1);
+			      clt_path->queue_depth * 3 + 1);
 		max_send_sge = 2;
 	}
 	atomic_set(&con->c.sq_wr_avail, max_send_wr);
 	cq_num = max_send_wr + max_recv_wr;
 	/* alloc iu to recv new rkey reply when server reports flags set */
-	if (sess->flags & RTRS_MSG_NEW_RKEY_F || con->c.cid == 0) {
+	if (clt_path->flags & RTRS_MSG_NEW_RKEY_F || con->c.cid == 0) {
 		con->rsp_ius = rtrs_iu_alloc(cq_num, sizeof(*rsp),
-					      GFP_KERNEL, sess->s.dev->ib_dev,
+					      GFP_KERNEL,
+					      clt_path->s.dev->ib_dev,
 					      DMA_FROM_DEVICE,
 					      rtrs_clt_rdma_done);
 		if (!con->rsp_ius)
@@ -1693,13 +1702,13 @@
 		con->queue_num = cq_num;
 	}
 	cq_num = max_send_wr + max_recv_wr;
-	cq_vector = con->cpu % sess->s.dev->ib_dev->num_comp_vectors;
-	if (con->c.cid >= sess->s.irq_con_num)
-		err = rtrs_cq_qp_create(&sess->s, &con->c, max_send_sge,
+	cq_vector = con->cpu % clt_path->s.dev->ib_dev->num_comp_vectors;
+	if (con->c.cid >= clt_path->s.irq_con_num)
+		err = rtrs_cq_qp_create(&clt_path->s, &con->c, max_send_sge,
 					cq_vector, cq_num, max_send_wr,
 					max_recv_wr, IB_POLL_DIRECT);
 	else
-		err = rtrs_cq_qp_create(&sess->s, &con->c, max_send_sge,
+		err = rtrs_cq_qp_create(&clt_path->s, &con->c, max_send_sge,
 					cq_vector, cq_num, max_send_wr,
 					max_recv_wr, IB_POLL_SOFTIRQ);
 	/*
@@ -1711,7 +1720,7 @@
 
 static void destroy_con_cq_qp(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 
 	/*
 	 * Be careful here: destroy_con_cq_qp() can be called even
@@ -1720,13 +1729,14 @@
 	lockdep_assert_held(&con->con_mutex);
 	rtrs_cq_qp_destroy(&con->c);
 	if (con->rsp_ius) {
-		rtrs_iu_free(con->rsp_ius, sess->s.dev->ib_dev, con->queue_num);
+		rtrs_iu_free(con->rsp_ius, clt_path->s.dev->ib_dev,
+			     con->queue_num);
 		con->rsp_ius = NULL;
 		con->queue_num = 0;
 	}
-	if (sess->s.dev_ref && !--sess->s.dev_ref) {
-		rtrs_ib_dev_put(sess->s.dev);
-		sess->s.dev = NULL;
+	if (clt_path->s.dev_ref && !--clt_path->s.dev_ref) {
+		rtrs_ib_dev_put(clt_path->s.dev);
+		clt_path->s.dev = NULL;
 	}
 }
 
@@ -1745,7 +1755,7 @@
 
 static int rtrs_rdma_addr_resolved(struct rtrs_clt_con *con)
 {
-	struct rtrs_sess *s = con->c.sess;
+	struct rtrs_path *s = con->c.path;
 	int err;
 
 	mutex_lock(&con->con_mutex);
@@ -1764,8 +1774,8 @@
 
 static int rtrs_rdma_route_resolved(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
+	struct rtrs_clt *clt = clt_path->clt;
 	struct rtrs_msg_conn_req msg;
 	struct rdma_conn_param param;
 
@@ -1782,11 +1792,11 @@
 		.magic = cpu_to_le16(RTRS_MAGIC),
 		.version = cpu_to_le16(RTRS_PROTO_VER),
 		.cid = cpu_to_le16(con->c.cid),
-		.cid_num = cpu_to_le16(sess->s.con_num),
-		.recon_cnt = cpu_to_le16(sess->s.recon_cnt),
+		.cid_num = cpu_to_le16(clt_path->s.con_num),
+		.recon_cnt = cpu_to_le16(clt_path->s.recon_cnt),
 	};
-	msg.first_conn = sess->for_new_clt ? FIRST_CONN : 0;
-	uuid_copy(&msg.sess_uuid, &sess->s.uuid);
+	msg.first_conn = clt_path->for_new_clt ? FIRST_CONN : 0;
+	uuid_copy(&msg.sess_uuid, &clt_path->s.uuid);
 	uuid_copy(&msg.paths_uuid, &clt->paths_uuid);
 
 	err = rdma_connect_locked(con->c.cm_id, &param);
@@ -1799,8 +1809,8 @@
 static int rtrs_rdma_conn_established(struct rtrs_clt_con *con,
 				       struct rdma_cm_event *ev)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
+	struct rtrs_clt *clt = clt_path->clt;
 	const struct rtrs_msg_conn_rsp *msg;
 	u16 version, queue_depth;
 	int errno;
@@ -1831,31 +1841,32 @@
 	if (con->c.cid == 0) {
 		queue_depth = le16_to_cpu(msg->queue_depth);
 
-		if (sess->queue_depth > 0 && queue_depth != sess->queue_depth) {
+		if (clt_path->queue_depth > 0 && queue_depth != clt_path->queue_depth) {
 			rtrs_err(clt, "Error: queue depth changed\n");
 
 			/*
 			 * Stop any more reconnection attempts
 			 */
-			sess->reconnect_attempts = -1;
+			clt_path->reconnect_attempts = -1;
 			rtrs_err(clt,
 				"Disabling auto-reconnect. Trigger a manual reconnect after issue is resolved\n");
 			return -ECONNRESET;
 		}
 
-		if (!sess->rbufs) {
-			sess->rbufs = kcalloc(queue_depth, sizeof(*sess->rbufs),
-					      GFP_KERNEL);
-			if (!sess->rbufs)
+		if (!clt_path->rbufs) {
+			clt_path->rbufs = kcalloc(queue_depth,
+						  sizeof(*clt_path->rbufs),
+						  GFP_KERNEL);
+			if (!clt_path->rbufs)
 				return -ENOMEM;
 		}
-		sess->queue_depth = queue_depth;
-		sess->s.signal_interval = min_not_zero(queue_depth,
+		clt_path->queue_depth = queue_depth;
+		clt_path->s.signal_interval = min_not_zero(queue_depth,
 						(unsigned short) SERVICE_CON_QUEUE_DEPTH);
-		sess->max_hdr_size = le32_to_cpu(msg->max_hdr_size);
-		sess->max_io_size = le32_to_cpu(msg->max_io_size);
-		sess->flags = le32_to_cpu(msg->flags);
-		sess->chunk_size = sess->max_io_size + sess->max_hdr_size;
+		clt_path->max_hdr_size = le32_to_cpu(msg->max_hdr_size);
+		clt_path->max_io_size = le32_to_cpu(msg->max_io_size);
+		clt_path->flags = le32_to_cpu(msg->flags);
+		clt_path->chunk_size = clt_path->max_io_size + clt_path->max_hdr_size;
 
 		/*
 		 * Global IO size is always a minimum.
@@ -1866,20 +1877,20 @@
 		 * connections in parallel, use lock.
 		 */
 		mutex_lock(&clt->paths_mutex);
-		clt->queue_depth = sess->queue_depth;
-		clt->max_io_size = min_not_zero(sess->max_io_size,
+		clt->queue_depth = clt_path->queue_depth;
+		clt->max_io_size = min_not_zero(clt_path->max_io_size,
 						clt->max_io_size);
 		mutex_unlock(&clt->paths_mutex);
 
 		/*
 		 * Cache the hca_port and hca_name for sysfs
 		 */
-		sess->hca_port = con->c.cm_id->port_num;
-		scnprintf(sess->hca_name, sizeof(sess->hca_name),
-			  sess->s.dev->ib_dev->name);
-		sess->s.src_addr = con->c.cm_id->route.addr.src_addr;
+		clt_path->hca_port = con->c.cm_id->port_num;
+		scnprintf(clt_path->hca_name, sizeof(clt_path->hca_name),
+			  clt_path->s.dev->ib_dev->name);
+		clt_path->s.src_addr = con->c.cm_id->route.addr.src_addr;
 		/* set for_new_clt, to allow future reconnect on any path */
-		sess->for_new_clt = 1;
+		clt_path->for_new_clt = 1;
 	}
 
 	return 0;
@@ -1887,16 +1898,16 @@
 
 static inline void flag_success_on_conn(struct rtrs_clt_con *con)
 {
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 
-	atomic_inc(&sess->connected_cnt);
+	atomic_inc(&clt_path->connected_cnt);
 	con->cm_err = 1;
 }
 
 static int rtrs_rdma_conn_rejected(struct rtrs_clt_con *con,
 				    struct rdma_cm_event *ev)
 {
-	struct rtrs_sess *s = con->c.sess;
+	struct rtrs_path *s = con->c.path;
 	const struct rtrs_msg_conn_rsp *msg;
 	const char *rej_msg;
 	int status, errno;
@@ -1924,23 +1935,23 @@
 	return -ECONNRESET;
 }
 
-void rtrs_clt_close_conns(struct rtrs_clt_sess *sess, bool wait)
+void rtrs_clt_close_conns(struct rtrs_clt_path *clt_path, bool wait)
 {
-	if (rtrs_clt_change_state_get_old(sess, RTRS_CLT_CLOSING, NULL))
-		queue_work(rtrs_wq, &sess->close_work);
+	if (rtrs_clt_change_state_get_old(clt_path, RTRS_CLT_CLOSING, NULL))
+		queue_work(rtrs_wq, &clt_path->close_work);
 	if (wait)
-		flush_work(&sess->close_work);
+		flush_work(&clt_path->close_work);
 }
 
 static inline void flag_error_on_conn(struct rtrs_clt_con *con, int cm_err)
 {
 	if (con->cm_err == 1) {
-		struct rtrs_clt_sess *sess;
+		struct rtrs_clt_path *clt_path;
 
-		sess = to_clt_sess(con->c.sess);
-		if (atomic_dec_and_test(&sess->connected_cnt))
+		clt_path = to_clt_path(con->c.path);
+		if (atomic_dec_and_test(&clt_path->connected_cnt))
 
-			wake_up(&sess->state_wq);
+			wake_up(&clt_path->state_wq);
 	}
 	con->cm_err = cm_err;
 }
@@ -1949,8 +1960,8 @@
 				     struct rdma_cm_event *ev)
 {
 	struct rtrs_clt_con *con = cm_id->context;
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_clt_sess *sess = to_clt_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_clt_path *clt_path = to_clt_path(s);
 	int cm_err = 0;
 
 	switch (ev->event) {
@@ -1968,7 +1979,7 @@
 			 * i.e. wake up without state change, but we set cm_err.
 			 */
 			flag_success_on_conn(con);
-			wake_up(&sess->state_wq);
+			wake_up(&clt_path->state_wq);
 			return 0;
 		}
 		break;
@@ -1997,7 +2008,7 @@
 		/*
 		 * Device removal is a special case.  Queue close and return 0.
 		 */
-		rtrs_clt_close_conns(sess, false);
+		rtrs_clt_close_conns(clt_path, false);
 		return 0;
 	default:
 		rtrs_err(s, "Unexpected RDMA CM error (CM event: %s, err: %d)\n",
@@ -2018,15 +2029,16 @@
 	return 0;
 }
 
+/* The caller should do the cleanup in case of error */
 static int create_cm(struct rtrs_clt_con *con)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_clt_sess *sess = to_clt_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_clt_path *clt_path = to_clt_path(s);
 	struct rdma_cm_id *cm_id;
 	int err;
 
 	cm_id = rdma_create_id(&init_net, rtrs_clt_rdma_cm_handler, con,
-			       sess->s.dst_addr.ss_family == AF_IB ?
+			       clt_path->s.dst_addr.ss_family == AF_IB ?
 			       RDMA_PS_IB : RDMA_PS_TCP, IB_QPT_RC);
 	if (IS_ERR(cm_id)) {
 		err = PTR_ERR(cm_id);
@@ -2040,14 +2052,14 @@
 	err = rdma_set_reuseaddr(cm_id, 1);
 	if (err != 0) {
 		rtrs_err(s, "Set address reuse failed, err: %d\n", err);
-		goto destroy_cm;
+		return err;
 	}
-	err = rdma_resolve_addr(cm_id, (struct sockaddr *)&sess->s.src_addr,
-				(struct sockaddr *)&sess->s.dst_addr,
+	err = rdma_resolve_addr(cm_id, (struct sockaddr *)&clt_path->s.src_addr,
+				(struct sockaddr *)&clt_path->s.dst_addr,
 				RTRS_CONNECT_TIMEOUT_MS);
 	if (err) {
 		rtrs_err(s, "Failed to resolve address, err: %d\n", err);
-		goto destroy_cm;
+		return err;
 	}
 	/*
 	 * Combine connection status and session events. This is needed
@@ -2055,41 +2067,27 @@
 	 * or session state was really changed to error by device removal.
 	 */
 	err = wait_event_interruptible_timeout(
-			sess->state_wq,
-			con->cm_err || sess->state != RTRS_CLT_CONNECTING,
+			clt_path->state_wq,
+			con->cm_err || clt_path->state != RTRS_CLT_CONNECTING,
 			msecs_to_jiffies(RTRS_CONNECT_TIMEOUT_MS));
 	if (err == 0 || err == -ERESTARTSYS) {
 		if (err == 0)
 			err = -ETIMEDOUT;
 		/* Timedout or interrupted */
-		goto errr;
-	}
-	if (con->cm_err < 0) {
-		err = con->cm_err;
-		goto errr;
+		return err;
 	}
-	if (READ_ONCE(sess->state) != RTRS_CLT_CONNECTING) {
+	if (con->cm_err < 0)
+		return con->cm_err;
+	if (READ_ONCE(clt_path->state) != RTRS_CLT_CONNECTING)
 		/* Device removal */
-		err = -ECONNABORTED;
-		goto errr;
-	}
+		return -ECONNABORTED;
 
 	return 0;
-
-errr:
-	stop_cm(con);
-	mutex_lock(&con->con_mutex);
-	destroy_con_cq_qp(con);
-	mutex_unlock(&con->con_mutex);
-destroy_cm:
-	destroy_cm(con);
-
-	return err;
 }
 
-static void rtrs_clt_sess_up(struct rtrs_clt_sess *sess)
+static void rtrs_clt_path_up(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt *clt = clt_path->clt;
 	int up;
 
 	/*
@@ -2113,19 +2111,19 @@
 	mutex_unlock(&clt->paths_ev_mutex);
 
 	/* Mark session as established */
-	sess->established = true;
-	sess->reconnect_attempts = 0;
-	sess->stats->reconnects.successful_cnt++;
+	clt_path->established = true;
+	clt_path->reconnect_attempts = 0;
+	clt_path->stats->reconnects.successful_cnt++;
 }
 
-static void rtrs_clt_sess_down(struct rtrs_clt_sess *sess)
+static void rtrs_clt_path_down(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt *clt = clt_path->clt;
 
-	if (!sess->established)
+	if (!clt_path->established)
 		return;
 
-	sess->established = false;
+	clt_path->established = false;
 	mutex_lock(&clt->paths_ev_mutex);
 	WARN_ON(!clt->paths_up);
 	if (--clt->paths_up == 0)
@@ -2133,19 +2131,19 @@
 	mutex_unlock(&clt->paths_ev_mutex);
 }
 
-static void rtrs_clt_stop_and_destroy_conns(struct rtrs_clt_sess *sess)
+static void rtrs_clt_stop_and_destroy_conns(struct rtrs_clt_path *clt_path)
 {
 	struct rtrs_clt_con *con;
 	unsigned int cid;
 
-	WARN_ON(READ_ONCE(sess->state) == RTRS_CLT_CONNECTED);
+	WARN_ON(READ_ONCE(clt_path->state) == RTRS_CLT_CONNECTED);
 
 	/*
 	 * Possible race with rtrs_clt_open(), when DEVICE_REMOVAL comes
 	 * exactly in between.  Start destroying after it finishes.
 	 */
-	mutex_lock(&sess->init_mutex);
-	mutex_unlock(&sess->init_mutex);
+	mutex_lock(&clt_path->init_mutex);
+	mutex_unlock(&clt_path->init_mutex);
 
 	/*
 	 * All IO paths must observe !CONNECTED state before we
@@ -2153,7 +2151,7 @@
 	 */
 	synchronize_rcu();
 
-	rtrs_stop_hb(&sess->s);
+	rtrs_stop_hb(&clt_path->s);
 
 	/*
 	 * The order it utterly crucial: firstly disconnect and complete all
@@ -2162,15 +2160,15 @@
 	 * eventually notify upper layer about session disconnection.
 	 */
 
-	for (cid = 0; cid < sess->s.con_num; cid++) {
-		if (!sess->s.con[cid])
+	for (cid = 0; cid < clt_path->s.con_num; cid++) {
+		if (!clt_path->s.con[cid])
 			break;
-		con = to_clt_con(sess->s.con[cid]);
+		con = to_clt_con(clt_path->s.con[cid]);
 		stop_cm(con);
 	}
-	fail_all_outstanding_reqs(sess);
-	free_sess_reqs(sess);
-	rtrs_clt_sess_down(sess);
+	fail_all_outstanding_reqs(clt_path);
+	free_path_reqs(clt_path);
+	rtrs_clt_path_down(clt_path);
 
 	/*
 	 * Wait for graceful shutdown, namely when peer side invokes
@@ -2180,13 +2178,14 @@
 	 * since CM does not fire anything.  That is fine, we are not in
 	 * hurry.
 	 */
-	wait_event_timeout(sess->state_wq, !atomic_read(&sess->connected_cnt),
+	wait_event_timeout(clt_path->state_wq,
+			   !atomic_read(&clt_path->connected_cnt),
 			   msecs_to_jiffies(RTRS_CONNECT_TIMEOUT_MS));
 
-	for (cid = 0; cid < sess->s.con_num; cid++) {
-		if (!sess->s.con[cid])
+	for (cid = 0; cid < clt_path->s.con_num; cid++) {
+		if (!clt_path->s.con[cid])
 			break;
-		con = to_clt_con(sess->s.con[cid]);
+		con = to_clt_con(clt_path->s.con[cid]);
 		mutex_lock(&con->con_mutex);
 		destroy_con_cq_qp(con);
 		mutex_unlock(&con->con_mutex);
@@ -2195,26 +2194,26 @@
 	}
 }
 
-static inline bool xchg_sessions(struct rtrs_clt_sess __rcu **rcu_ppcpu_path,
-				 struct rtrs_clt_sess *sess,
-				 struct rtrs_clt_sess *next)
+static inline bool xchg_paths(struct rtrs_clt_path __rcu **rcu_ppcpu_path,
+			      struct rtrs_clt_path *clt_path,
+			      struct rtrs_clt_path *next)
 {
-	struct rtrs_clt_sess **ppcpu_path;
+	struct rtrs_clt_path **ppcpu_path;
 
 	/* Call cmpxchg() without sparse warnings */
 	ppcpu_path = (typeof(ppcpu_path))rcu_ppcpu_path;
-	return sess == cmpxchg(ppcpu_path, sess, next);
+	return clt_path == cmpxchg(ppcpu_path, clt_path, next);
 }
 
-static void rtrs_clt_remove_path_from_arr(struct rtrs_clt_sess *sess)
+static void rtrs_clt_remove_path_from_arr(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt *clt = sess->clt;
-	struct rtrs_clt_sess *next;
+	struct rtrs_clt *clt = clt_path->clt;
+	struct rtrs_clt_path *next;
 	bool wait_for_grace = false;
 	int cpu;
 
 	mutex_lock(&clt->paths_mutex);
-	list_del_rcu(&sess->s.entry);
+	list_del_rcu(&clt_path->s.entry);
 
 	/* Make sure everybody observes path removal. */
 	synchronize_rcu();
@@ -2255,8 +2254,7 @@
 	 * removed.  If @sess is the last element, then @next is NULL.
 	 */
 	rcu_read_lock();
-	next = list_next_or_null_rr_rcu(&clt->paths_list, &sess->s.entry,
-					typeof(*next), s.entry);
+	next = rtrs_clt_get_next_path_or_null(&clt->paths_list, clt_path);
 	rcu_read_unlock();
 
 	/*
@@ -2264,11 +2262,11 @@
 	 * removed, so change the pointer manually.
 	 */
 	for_each_possible_cpu(cpu) {
-		struct rtrs_clt_sess __rcu **ppcpu_path;
+		struct rtrs_clt_path __rcu **ppcpu_path;
 
 		ppcpu_path = per_cpu_ptr(clt->pcpu_path, cpu);
 		if (rcu_dereference_protected(*ppcpu_path,
-			lockdep_is_held(&clt->paths_mutex)) != sess)
+			lockdep_is_held(&clt->paths_mutex)) != clt_path)
 			/*
 			 * synchronize_rcu() was called just after deleting
 			 * entry from the list, thus IO code path cannot
@@ -2281,7 +2279,7 @@
 		 * We race with IO code path, which also changes pointer,
 		 * thus we have to be careful not to overwrite it.
 		 */
-		if (xchg_sessions(ppcpu_path, sess, next))
+		if (xchg_paths(ppcpu_path, clt_path, next))
 			/*
 			 * @ppcpu_path was successfully replaced with @next,
 			 * that means that someone could also pick up the
@@ -2296,70 +2294,78 @@
 	mutex_unlock(&clt->paths_mutex);
 }
 
-static void rtrs_clt_add_path_to_arr(struct rtrs_clt_sess *sess)
+static void rtrs_clt_add_path_to_arr(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt *clt = sess->clt;
+	struct rtrs_clt *clt = clt_path->clt;
 
 	mutex_lock(&clt->paths_mutex);
 	clt->paths_num++;
 
-	list_add_tail_rcu(&sess->s.entry, &clt->paths_list);
+	list_add_tail_rcu(&clt_path->s.entry, &clt->paths_list);
 	mutex_unlock(&clt->paths_mutex);
 }
 
 static void rtrs_clt_close_work(struct work_struct *work)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
-	sess = container_of(work, struct rtrs_clt_sess, close_work);
+	clt_path = container_of(work, struct rtrs_clt_path, close_work);
 
-	cancel_delayed_work_sync(&sess->reconnect_dwork);
-	rtrs_clt_stop_and_destroy_conns(sess);
-	rtrs_clt_change_state_get_old(sess, RTRS_CLT_CLOSED, NULL);
+	cancel_delayed_work_sync(&clt_path->reconnect_dwork);
+	rtrs_clt_stop_and_destroy_conns(clt_path);
+	rtrs_clt_change_state_get_old(clt_path, RTRS_CLT_CLOSED, NULL);
 }
 
-static int init_conns(struct rtrs_clt_sess *sess)
+static int init_conns(struct rtrs_clt_path *clt_path)
 {
 	unsigned int cid;
-	int err;
+	int err, i;
 
 	/*
 	 * On every new session connections increase reconnect counter
 	 * to avoid clashes with previous sessions not yet closed
 	 * sessions on a server side.
 	 */
-	sess->s.recon_cnt++;
+	clt_path->s.recon_cnt++;
 
 	/* Establish all RDMA connections  */
-	for (cid = 0; cid < sess->s.con_num; cid++) {
-		err = create_con(sess, cid);
+	for (cid = 0; cid < clt_path->s.con_num; cid++) {
+		err = create_con(clt_path, cid);
 		if (err)
 			goto destroy;
 
-		err = create_cm(to_clt_con(sess->s.con[cid]));
-		if (err) {
-			destroy_con(to_clt_con(sess->s.con[cid]));
+		err = create_cm(to_clt_con(clt_path->s.con[cid]));
+		if (err)
 			goto destroy;
-		}
 	}
-	err = alloc_sess_reqs(sess);
+
+	/*
+	 * Set the cid to con_num - 1, since if we fail later, we want to stay in bounds.
+	 */
+	cid = clt_path->s.con_num - 1;
+
+	err = alloc_path_reqs(clt_path);
 	if (err)
 		goto destroy;
 
-	rtrs_start_hb(&sess->s);
-
 	return 0;
 
 destroy:
-	while (cid--) {
-		struct rtrs_clt_con *con = to_clt_con(sess->s.con[cid]);
+	/* Make sure we do the cleanup in the order they are created */
+	for (i = 0; i <= cid; i++) {
+		struct rtrs_clt_con *con;
 
-		stop_cm(con);
+		if (!clt_path->s.con[i])
+			break;
 
-		mutex_lock(&con->con_mutex);
-		destroy_con_cq_qp(con);
-		mutex_unlock(&con->con_mutex);
-		destroy_cm(con);
+		con = to_clt_con(clt_path->s.con[i]);
+		if (con->c.cm_id) {
+			stop_cm(con);
+			mutex_lock(&con->con_mutex);
+			destroy_con_cq_qp(con);
+			mutex_unlock(&con->con_mutex);
+			destroy_cm(con);
+		}
 		destroy_con(con);
 	}
 	/*
@@ -2367,7 +2373,7 @@
 	 * doing rdma_resolve_addr(), switch to CONNECTION_ERR state
 	 * manually to keep reconnecting.
 	 */
-	rtrs_clt_change_state_get_old(sess, RTRS_CLT_CONNECTING_ERR, NULL);
+	rtrs_clt_change_state_get_old(clt_path, RTRS_CLT_CONNECTING_ERR, NULL);
 
 	return err;
 }
@@ -2375,31 +2381,32 @@
 static void rtrs_clt_info_req_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_clt_con *con = to_clt_con(wc->qp->qp_context);
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	struct rtrs_iu *iu;
 
 	iu = container_of(wc->wr_cqe, struct rtrs_iu, cqe);
-	rtrs_iu_free(iu, sess->s.dev->ib_dev, 1);
+	rtrs_iu_free(iu, clt_path->s.dev->ib_dev, 1);
 
 	if (wc->status != IB_WC_SUCCESS) {
-		rtrs_err(sess->clt, "Sess info request send failed: %s\n",
+		rtrs_err(clt_path->clt, "Path info request send failed: %s\n",
 			  ib_wc_status_msg(wc->status));
-		rtrs_clt_change_state_get_old(sess, RTRS_CLT_CONNECTING_ERR, NULL);
+		rtrs_clt_change_state_get_old(clt_path, RTRS_CLT_CONNECTING_ERR, NULL);
 		return;
 	}
 
 	rtrs_clt_update_wc_stats(con);
 }
 
-static int process_info_rsp(struct rtrs_clt_sess *sess,
+static int process_info_rsp(struct rtrs_clt_path *clt_path,
 			    const struct rtrs_msg_info_rsp *msg)
 {
 	unsigned int sg_cnt, total_len;
 	int i, sgi;
 
 	sg_cnt = le16_to_cpu(msg->sg_cnt);
-	if (!sg_cnt || (sess->queue_depth % sg_cnt)) {
-		rtrs_err(sess->clt, "Incorrect sg_cnt %d, is not multiple\n",
+	if (!sg_cnt || (clt_path->queue_depth % sg_cnt)) {
+		rtrs_err(clt_path->clt,
+			  "Incorrect sg_cnt %d, is not multiple\n",
 			  sg_cnt);
 		return -EINVAL;
 	}
@@ -2408,15 +2415,15 @@
 	 * Check if IB immediate data size is enough to hold the mem_id and
 	 * the offset inside the memory chunk.
 	 */
-	if ((ilog2(sg_cnt - 1) + 1) + (ilog2(sess->chunk_size - 1) + 1) >
+	if ((ilog2(sg_cnt - 1) + 1) + (ilog2(clt_path->chunk_size - 1) + 1) >
 	    MAX_IMM_PAYL_BITS) {
-		rtrs_err(sess->clt,
+		rtrs_err(clt_path->clt,
 			  "RDMA immediate size (%db) not enough to encode %d buffers of size %dB\n",
-			  MAX_IMM_PAYL_BITS, sg_cnt, sess->chunk_size);
+			  MAX_IMM_PAYL_BITS, sg_cnt, clt_path->chunk_size);
 		return -EINVAL;
 	}
 	total_len = 0;
-	for (sgi = 0, i = 0; sgi < sg_cnt && i < sess->queue_depth; sgi++) {
+	for (sgi = 0, i = 0; sgi < sg_cnt && i < clt_path->queue_depth; sgi++) {
 		const struct rtrs_sg_desc *desc = &msg->desc[sgi];
 		u32 len, rkey;
 		u64 addr;
@@ -2427,26 +2434,28 @@
 
 		total_len += len;
 
-		if (!len || (len % sess->chunk_size)) {
-			rtrs_err(sess->clt, "Incorrect [%d].len %d\n", sgi,
+		if (!len || (len % clt_path->chunk_size)) {
+			rtrs_err(clt_path->clt, "Incorrect [%d].len %d\n",
+				  sgi,
 				  len);
 			return -EINVAL;
 		}
-		for ( ; len && i < sess->queue_depth; i++) {
-			sess->rbufs[i].addr = addr;
-			sess->rbufs[i].rkey = rkey;
+		for ( ; len && i < clt_path->queue_depth; i++) {
+			clt_path->rbufs[i].addr = addr;
+			clt_path->rbufs[i].rkey = rkey;
 
-			len  -= sess->chunk_size;
-			addr += sess->chunk_size;
+			len  -= clt_path->chunk_size;
+			addr += clt_path->chunk_size;
 		}
 	}
 	/* Sanity check */
-	if (sgi != sg_cnt || i != sess->queue_depth) {
-		rtrs_err(sess->clt, "Incorrect sg vector, not fully mapped\n");
+	if (sgi != sg_cnt || i != clt_path->queue_depth) {
+		rtrs_err(clt_path->clt,
+			 "Incorrect sg vector, not fully mapped\n");
 		return -EINVAL;
 	}
-	if (total_len != sess->chunk_size * sess->queue_depth) {
-		rtrs_err(sess->clt, "Incorrect total_len %d\n", total_len);
+	if (total_len != clt_path->chunk_size * clt_path->queue_depth) {
+		rtrs_err(clt_path->clt, "Incorrect total_len %d\n", total_len);
 		return -EINVAL;
 	}
 
@@ -2456,7 +2465,7 @@
 static void rtrs_clt_info_rsp_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_clt_con *con = to_clt_con(wc->qp->qp_context);
-	struct rtrs_clt_sess *sess = to_clt_sess(con->c.sess);
+	struct rtrs_clt_path *clt_path = to_clt_path(con->c.path);
 	struct rtrs_msg_info_rsp *msg;
 	enum rtrs_clt_state state;
 	struct rtrs_iu *iu;
@@ -2468,37 +2477,37 @@
 	WARN_ON(con->c.cid);
 	iu = container_of(wc->wr_cqe, struct rtrs_iu, cqe);
 	if (wc->status != IB_WC_SUCCESS) {
-		rtrs_err(sess->clt, "Sess info response recv failed: %s\n",
+		rtrs_err(clt_path->clt, "Path info response recv failed: %s\n",
 			  ib_wc_status_msg(wc->status));
 		goto out;
 	}
 	WARN_ON(wc->opcode != IB_WC_RECV);
 
 	if (wc->byte_len < sizeof(*msg)) {
-		rtrs_err(sess->clt, "Sess info response is malformed: size %d\n",
+		rtrs_err(clt_path->clt, "Path info response is malformed: size %d\n",
 			  wc->byte_len);
 		goto out;
 	}
-	ib_dma_sync_single_for_cpu(sess->s.dev->ib_dev, iu->dma_addr,
+	ib_dma_sync_single_for_cpu(clt_path->s.dev->ib_dev, iu->dma_addr,
 				   iu->size, DMA_FROM_DEVICE);
 	msg = iu->buf;
 	if (le16_to_cpu(msg->type) != RTRS_MSG_INFO_RSP) {
-		rtrs_err(sess->clt, "Sess info response is malformed: type %d\n",
+		rtrs_err(clt_path->clt, "Path info response is malformed: type %d\n",
 			  le16_to_cpu(msg->type));
 		goto out;
 	}
 	rx_sz  = sizeof(*msg);
 	rx_sz += sizeof(msg->desc[0]) * le16_to_cpu(msg->sg_cnt);
 	if (wc->byte_len < rx_sz) {
-		rtrs_err(sess->clt, "Sess info response is malformed: size %d\n",
+		rtrs_err(clt_path->clt, "Path info response is malformed: size %d\n",
 			  wc->byte_len);
 		goto out;
 	}
-	err = process_info_rsp(sess, msg);
+	err = process_info_rsp(clt_path, msg);
 	if (err)
 		goto out;
 
-	err = post_recv_sess(sess);
+	err = post_recv_path(clt_path);
 	if (err)
 		goto out;
 
@@ -2506,25 +2515,25 @@
 
 out:
 	rtrs_clt_update_wc_stats(con);
-	rtrs_iu_free(iu, sess->s.dev->ib_dev, 1);
-	rtrs_clt_change_state_get_old(sess, state, NULL);
+	rtrs_iu_free(iu, clt_path->s.dev->ib_dev, 1);
+	rtrs_clt_change_state_get_old(clt_path, state, NULL);
 }
 
-static int rtrs_send_sess_info(struct rtrs_clt_sess *sess)
+static int rtrs_send_path_info(struct rtrs_clt_path *clt_path)
 {
-	struct rtrs_clt_con *usr_con = to_clt_con(sess->s.con[0]);
+	struct rtrs_clt_con *usr_con = to_clt_con(clt_path->s.con[0]);
 	struct rtrs_msg_info_req *msg;
 	struct rtrs_iu *tx_iu, *rx_iu;
 	size_t rx_sz;
 	int err;
 
 	rx_sz  = sizeof(struct rtrs_msg_info_rsp);
-	rx_sz += sizeof(struct rtrs_sg_desc) * sess->queue_depth;
+	rx_sz += sizeof(struct rtrs_sg_desc) * clt_path->queue_depth;
 
 	tx_iu = rtrs_iu_alloc(1, sizeof(struct rtrs_msg_info_req), GFP_KERNEL,
-			       sess->s.dev->ib_dev, DMA_TO_DEVICE,
+			       clt_path->s.dev->ib_dev, DMA_TO_DEVICE,
 			       rtrs_clt_info_req_done);
-	rx_iu = rtrs_iu_alloc(1, rx_sz, GFP_KERNEL, sess->s.dev->ib_dev,
+	rx_iu = rtrs_iu_alloc(1, rx_sz, GFP_KERNEL, clt_path->s.dev->ib_dev,
 			       DMA_FROM_DEVICE, rtrs_clt_info_rsp_done);
 	if (!tx_iu || !rx_iu) {
 		err = -ENOMEM;
@@ -2533,33 +2542,34 @@
 	/* Prepare for getting info response */
 	err = rtrs_iu_post_recv(&usr_con->c, rx_iu);
 	if (err) {
-		rtrs_err(sess->clt, "rtrs_iu_post_recv(), err: %d\n", err);
+		rtrs_err(clt_path->clt, "rtrs_iu_post_recv(), err: %d\n", err);
 		goto out;
 	}
 	rx_iu = NULL;
 
 	msg = tx_iu->buf;
 	msg->type = cpu_to_le16(RTRS_MSG_INFO_REQ);
-	memcpy(msg->sessname, sess->s.sessname, sizeof(msg->sessname));
+	memcpy(msg->pathname, clt_path->s.sessname, sizeof(msg->pathname));
 
-	ib_dma_sync_single_for_device(sess->s.dev->ib_dev, tx_iu->dma_addr,
+	ib_dma_sync_single_for_device(clt_path->s.dev->ib_dev,
+				      tx_iu->dma_addr,
 				      tx_iu->size, DMA_TO_DEVICE);
 
 	/* Send info request */
 	err = rtrs_iu_post_send(&usr_con->c, tx_iu, sizeof(*msg), NULL);
 	if (err) {
-		rtrs_err(sess->clt, "rtrs_iu_post_send(), err: %d\n", err);
+		rtrs_err(clt_path->clt, "rtrs_iu_post_send(), err: %d\n", err);
 		goto out;
 	}
 	tx_iu = NULL;
 
 	/* Wait for state change */
-	wait_event_interruptible_timeout(sess->state_wq,
-					 sess->state != RTRS_CLT_CONNECTING,
+	wait_event_interruptible_timeout(clt_path->state_wq,
+					 clt_path->state != RTRS_CLT_CONNECTING,
 					 msecs_to_jiffies(
 						 RTRS_CONNECT_TIMEOUT_MS));
-	if (READ_ONCE(sess->state) != RTRS_CLT_CONNECTED) {
-		if (READ_ONCE(sess->state) == RTRS_CLT_CONNECTING_ERR)
+	if (READ_ONCE(clt_path->state) != RTRS_CLT_CONNECTED) {
+		if (READ_ONCE(clt_path->state) == RTRS_CLT_CONNECTING_ERR)
 			err = -ECONNRESET;
 		else
 			err = -ETIMEDOUT;
@@ -2567,82 +2577,83 @@
 
 out:
 	if (tx_iu)
-		rtrs_iu_free(tx_iu, sess->s.dev->ib_dev, 1);
+		rtrs_iu_free(tx_iu, clt_path->s.dev->ib_dev, 1);
 	if (rx_iu)
-		rtrs_iu_free(rx_iu, sess->s.dev->ib_dev, 1);
+		rtrs_iu_free(rx_iu, clt_path->s.dev->ib_dev, 1);
 	if (err)
 		/* If we've never taken async path because of malloc problems */
-		rtrs_clt_change_state_get_old(sess, RTRS_CLT_CONNECTING_ERR, NULL);
+		rtrs_clt_change_state_get_old(clt_path,
+					      RTRS_CLT_CONNECTING_ERR, NULL);
 
 	return err;
 }
 
 /**
- * init_sess() - establishes all session connections and does handshake
- * @sess: client session.
+ * init_path() - establishes all path connections and does handshake
+ * @clt_path: client path.
  * In case of error full close or reconnect procedure should be taken,
  * because reconnect or close async works can be started.
  */
-static int init_sess(struct rtrs_clt_sess *sess)
+static int init_path(struct rtrs_clt_path *clt_path)
 {
 	int err;
 	char str[NAME_MAX];
 	struct rtrs_addr path = {
-		.src = &sess->s.src_addr,
-		.dst = &sess->s.dst_addr,
+		.src = &clt_path->s.src_addr,
+		.dst = &clt_path->s.dst_addr,
 	};
 
 	rtrs_addr_to_str(&path, str, sizeof(str));
 
-	mutex_lock(&sess->init_mutex);
-	err = init_conns(sess);
+	mutex_lock(&clt_path->init_mutex);
+	err = init_conns(clt_path);
 	if (err) {
-		rtrs_err(sess->clt,
+		rtrs_err(clt_path->clt,
 			 "init_conns() failed: err=%d path=%s [%s:%u]\n", err,
-			 str, sess->hca_name, sess->hca_port);
+			 str, clt_path->hca_name, clt_path->hca_port);
 		goto out;
 	}
-	err = rtrs_send_sess_info(sess);
+	err = rtrs_send_path_info(clt_path);
 	if (err) {
-		rtrs_err(
-			sess->clt,
-			"rtrs_send_sess_info() failed: err=%d path=%s [%s:%u]\n",
-			err, str, sess->hca_name, sess->hca_port);
+		rtrs_err(clt_path->clt,
+			 "rtrs_send_path_info() failed: err=%d path=%s [%s:%u]\n",
+			 err, str, clt_path->hca_name, clt_path->hca_port);
 		goto out;
 	}
-	rtrs_clt_sess_up(sess);
+	rtrs_clt_path_up(clt_path);
+	rtrs_start_hb(&clt_path->s);
 out:
-	mutex_unlock(&sess->init_mutex);
+	mutex_unlock(&clt_path->init_mutex);
 
 	return err;
 }
 
 static void rtrs_clt_reconnect_work(struct work_struct *work)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	struct rtrs_clt *clt;
 	unsigned int delay_ms;
 	int err;
 
-	sess = container_of(to_delayed_work(work), struct rtrs_clt_sess,
-			    reconnect_dwork);
-	clt = sess->clt;
+	clt_path = container_of(to_delayed_work(work), struct rtrs_clt_path,
+				reconnect_dwork);
+	clt = clt_path->clt;
 
-	if (READ_ONCE(sess->state) != RTRS_CLT_RECONNECTING)
+	if (READ_ONCE(clt_path->state) != RTRS_CLT_RECONNECTING)
 		return;
 
-	if (sess->reconnect_attempts >= clt->max_reconnect_attempts) {
-		/* Close a session completely if max attempts is reached */
-		rtrs_clt_close_conns(sess, false);
+	if (clt_path->reconnect_attempts >= clt->max_reconnect_attempts) {
+		/* Close a path completely if max attempts is reached */
+		rtrs_clt_close_conns(clt_path, false);
 		return;
 	}
-	sess->reconnect_attempts++;
+	clt_path->reconnect_attempts++;
 
 	/* Stop everything */
-	rtrs_clt_stop_and_destroy_conns(sess);
+	rtrs_clt_stop_and_destroy_conns(clt_path);
 	msleep(RTRS_RECONNECT_BACKOFF);
-	if (rtrs_clt_change_state_get_old(sess, RTRS_CLT_CONNECTING, NULL)) {
-		err = init_sess(sess);
+	if (rtrs_clt_change_state_get_old(clt_path, RTRS_CLT_CONNECTING, NULL)) {
+		err = init_path(clt_path);
 		if (err)
 			goto reconnect_again;
 	}
@@ -2650,10 +2661,10 @@
 	return;
 
 reconnect_again:
-	if (rtrs_clt_change_state_get_old(sess, RTRS_CLT_RECONNECTING, NULL)) {
-		sess->stats->reconnects.fail_cnt++;
+	if (rtrs_clt_change_state_get_old(clt_path, RTRS_CLT_RECONNECTING, NULL)) {
+		clt_path->stats->reconnects.fail_cnt++;
 		delay_ms = clt->reconnect_delay_sec * 1000;
-		queue_delayed_work(rtrs_wq, &sess->reconnect_dwork,
+		queue_delayed_work(rtrs_wq, &clt_path->reconnect_dwork,
 				   msecs_to_jiffies(delay_ms +
 						    prandom_u32() %
 						    RTRS_RECONNECT_SEED));
@@ -2664,6 +2675,8 @@
 {
 	struct rtrs_clt *clt = container_of(dev, struct rtrs_clt, dev);
 
+	mutex_destroy(&clt->paths_ev_mutex);
+	mutex_destroy(&clt->paths_mutex);
 	kfree(clt);
 }
 
@@ -2693,6 +2706,8 @@
 		return ERR_PTR(-ENOMEM);
 	}
 
+	clt->dev.class = rtrs_clt_dev_class;
+	clt->dev.release = rtrs_clt_dev_release;
 	uuid_gen(&clt->paths_uuid);
 	INIT_LIST_HEAD_RCU(&clt->paths_list);
 	clt->paths_num = paths_num;
@@ -2709,58 +2724,56 @@
 	init_waitqueue_head(&clt->permits_wait);
 	mutex_init(&clt->paths_ev_mutex);
 	mutex_init(&clt->paths_mutex);
+	device_initialize(&clt->dev);
 
-	clt->dev.class = rtrs_clt_dev_class;
-	clt->dev.release = rtrs_clt_dev_release;
 	err = dev_set_name(&clt->dev, "%s", sessname);
 	if (err)
-		goto err;
+		goto err_put;
+
 	/*
 	 * Suppress user space notification until
 	 * sysfs files are created
 	 */
 	dev_set_uevent_suppress(&clt->dev, true);
-	err = device_register(&clt->dev);
-	if (err) {
-		put_device(&clt->dev);
-		goto err;
-	}
+	err = device_add(&clt->dev);
+	if (err)
+		goto err_put;
 
 	clt->kobj_paths = kobject_create_and_add("paths", &clt->dev.kobj);
 	if (!clt->kobj_paths) {
 		err = -ENOMEM;
-		goto err_dev;
+		goto err_del;
 	}
 	err = rtrs_clt_create_sysfs_root_files(clt);
 	if (err) {
 		kobject_del(clt->kobj_paths);
 		kobject_put(clt->kobj_paths);
-		goto err_dev;
+		goto err_del;
 	}
 	dev_set_uevent_suppress(&clt->dev, false);
 	kobject_uevent(&clt->dev.kobj, KOBJ_ADD);
 
 	return clt;
-err_dev:
-	device_unregister(&clt->dev);
-err:
+err_del:
+	device_del(&clt->dev);
+err_put:
 	free_percpu(clt->pcpu_path);
-	kfree(clt);
+	put_device(&clt->dev);
 	return ERR_PTR(err);
 }
 
 static void free_clt(struct rtrs_clt *clt)
 {
-	free_permits(clt);
 	free_percpu(clt->pcpu_path);
-	mutex_destroy(&clt->paths_ev_mutex);
-	mutex_destroy(&clt->paths_mutex);
-	/* release callback will free clt in last put */
+
+	/*
+	 * release callback will free clt and destroy mutexes in last put
+	 */
 	device_unregister(&clt->dev);
 }
 
 /**
- * rtrs_clt_open() - Open a session to an RTRS server
+ * rtrs_clt_open() - Open a path to an RTRS server
  * @ops: holds the link event callback and the private pointer.
  * @sessname: name of the session
  * @paths: Paths to be established defined by their src and dst addresses
@@ -2778,17 +2791,23 @@
  * Return a valid pointer on success otherwise PTR_ERR.
  */
 struct rtrs_clt *rtrs_clt_open(struct rtrs_clt_ops *ops,
-				 const char *sessname,
+				 const char *pathname,
 				 const struct rtrs_addr *paths,
 				 size_t paths_num, u16 port,
 				 size_t pdu_sz, u8 reconnect_delay_sec,
 				 s16 max_reconnect_attempts, u32 nr_poll_queues)
 {
-	struct rtrs_clt_sess *sess, *tmp;
+	struct rtrs_clt_path *clt_path, *tmp;
 	struct rtrs_clt *clt;
 	int err, i;
 
-	clt = alloc_clt(sessname, paths_num, port, pdu_sz, ops->priv,
+	if (strchr(pathname, '/') || strchr(pathname, '.')) {
+		pr_err("pathname cannot contain / and .\n");
+		err = -EINVAL;
+		goto out;
+	}
+
+	clt = alloc_clt(pathname, paths_num, port, pdu_sz, ops->priv,
 			ops->link_ev,
 			reconnect_delay_sec,
 			max_reconnect_attempts);
@@ -2797,49 +2816,49 @@
 		goto out;
 	}
 	for (i = 0; i < paths_num; i++) {
-		struct rtrs_clt_sess *sess;
+		struct rtrs_clt_path *clt_path;
 
-		sess = alloc_sess(clt, &paths[i], nr_cpu_ids,
+		clt_path = alloc_path(clt, &paths[i], nr_cpu_ids,
 				  nr_poll_queues);
-		if (IS_ERR(sess)) {
-			err = PTR_ERR(sess);
-			goto close_all_sess;
+		if (IS_ERR(clt_path)) {
+			err = PTR_ERR(clt_path);
+			goto close_all_path;
 		}
 		if (!i)
-			sess->for_new_clt = 1;
-		list_add_tail_rcu(&sess->s.entry, &clt->paths_list);
+			clt_path->for_new_clt = 1;
+		list_add_tail_rcu(&clt_path->s.entry, &clt->paths_list);
 
-		err = init_sess(sess);
+		err = init_path(clt_path);
 		if (err) {
-			list_del_rcu(&sess->s.entry);
-			rtrs_clt_close_conns(sess, true);
-			free_percpu(sess->stats->pcpu_stats);
-			kfree(sess->stats);
-			free_sess(sess);
-			goto close_all_sess;
+			list_del_rcu(&clt_path->s.entry);
+			rtrs_clt_close_conns(clt_path, true);
+			free_percpu(clt_path->stats->pcpu_stats);
+			kfree(clt_path->stats);
+			free_path(clt_path);
+			goto close_all_path;
 		}
 
-		err = rtrs_clt_create_sess_files(sess);
+		err = rtrs_clt_create_path_files(clt_path);
 		if (err) {
-			list_del_rcu(&sess->s.entry);
-			rtrs_clt_close_conns(sess, true);
-			free_percpu(sess->stats->pcpu_stats);
-			kfree(sess->stats);
-			free_sess(sess);
-			goto close_all_sess;
+			list_del_rcu(&clt_path->s.entry);
+			rtrs_clt_close_conns(clt_path, true);
+			free_percpu(clt_path->stats->pcpu_stats);
+			kfree(clt_path->stats);
+			free_path(clt_path);
+			goto close_all_path;
 		}
 	}
 	err = alloc_permits(clt);
 	if (err)
-		goto close_all_sess;
+		goto close_all_path;
 
 	return clt;
 
-close_all_sess:
-	list_for_each_entry_safe(sess, tmp, &clt->paths_list, s.entry) {
-		rtrs_clt_destroy_sess_files(sess, NULL);
-		rtrs_clt_close_conns(sess, true);
-		kobject_put(&sess->kobj);
+close_all_path:
+	list_for_each_entry_safe(clt_path, tmp, &clt->paths_list, s.entry) {
+		rtrs_clt_destroy_path_files(clt_path, NULL);
+		rtrs_clt_close_conns(clt_path, true);
+		kobject_put(&clt_path->kobj);
 	}
 	rtrs_clt_destroy_sysfs_root(clt);
 	free_clt(clt);
@@ -2850,37 +2869,39 @@
 EXPORT_SYMBOL(rtrs_clt_open);
 
 /**
- * rtrs_clt_close() - Close a session
+ * rtrs_clt_close() - Close a path
  * @clt: Session handle. Session is freed upon return.
  */
 void rtrs_clt_close(struct rtrs_clt *clt)
 {
-	struct rtrs_clt_sess *sess, *tmp;
+	struct rtrs_clt_path *clt_path, *tmp;
 
 	/* Firstly forbid sysfs access */
 	rtrs_clt_destroy_sysfs_root(clt);
 
 	/* Now it is safe to iterate over all paths without locks */
-	list_for_each_entry_safe(sess, tmp, &clt->paths_list, s.entry) {
-		rtrs_clt_close_conns(sess, true);
-		rtrs_clt_destroy_sess_files(sess, NULL);
-		kobject_put(&sess->kobj);
+	list_for_each_entry_safe(clt_path, tmp, &clt->paths_list, s.entry) {
+		rtrs_clt_close_conns(clt_path, true);
+		rtrs_clt_destroy_path_files(clt_path, NULL);
+		kobject_put(&clt_path->kobj);
 	}
+	free_permits(clt);
 	free_clt(clt);
 }
 EXPORT_SYMBOL(rtrs_clt_close);
 
-int rtrs_clt_reconnect_from_sysfs(struct rtrs_clt_sess *sess)
+int rtrs_clt_reconnect_from_sysfs(struct rtrs_clt_path *clt_path)
 {
 	enum rtrs_clt_state old_state;
 	int err = -EBUSY;
 	bool changed;
 
-	changed = rtrs_clt_change_state_get_old(sess, RTRS_CLT_RECONNECTING,
+	changed = rtrs_clt_change_state_get_old(clt_path,
+						 RTRS_CLT_RECONNECTING,
 						 &old_state);
 	if (changed) {
-		sess->reconnect_attempts = 0;
-		queue_delayed_work(rtrs_wq, &sess->reconnect_dwork, 0);
+		clt_path->reconnect_attempts = 0;
+		queue_delayed_work(rtrs_wq, &clt_path->reconnect_dwork, 0);
 	}
 	if (changed || old_state == RTRS_CLT_RECONNECTING) {
 		/*
@@ -2888,15 +2909,15 @@
 		 * execution, so do the flush if we have queued something
 		 * right now or work is pending.
 		 */
-		flush_delayed_work(&sess->reconnect_dwork);
-		err = (READ_ONCE(sess->state) ==
+		flush_delayed_work(&clt_path->reconnect_dwork);
+		err = (READ_ONCE(clt_path->state) ==
 		       RTRS_CLT_CONNECTED ? 0 : -ENOTCONN);
 	}
 
 	return err;
 }
 
-int rtrs_clt_remove_path_from_sysfs(struct rtrs_clt_sess *sess,
+int rtrs_clt_remove_path_from_sysfs(struct rtrs_clt_path *clt_path,
 				     const struct attribute *sysfs_self)
 {
 	enum rtrs_clt_state old_state;
@@ -2912,16 +2933,16 @@
 	 *    removing the path.
 	 */
 	do {
-		rtrs_clt_close_conns(sess, true);
-		changed = rtrs_clt_change_state_get_old(sess,
+		rtrs_clt_close_conns(clt_path, true);
+		changed = rtrs_clt_change_state_get_old(clt_path,
 							RTRS_CLT_DEAD,
 							&old_state);
 	} while (!changed && old_state != RTRS_CLT_DEAD);
 
 	if (changed) {
-		rtrs_clt_remove_path_from_arr(sess);
-		rtrs_clt_destroy_sess_files(sess, sysfs_self);
-		kobject_put(&sess->kobj);
+		rtrs_clt_remove_path_from_arr(clt_path);
+		rtrs_clt_destroy_path_files(clt_path, sysfs_self);
+		kobject_put(&clt_path->kobj);
 	}
 
 	return 0;
@@ -2967,7 +2988,7 @@
 		      struct scatterlist *sg, unsigned int sg_cnt)
 {
 	struct rtrs_clt_io_req *req;
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 
 	enum dma_data_direction dma_dir;
 	int err = -ECONNABORTED, i;
@@ -2989,19 +3010,19 @@
 
 	rcu_read_lock();
 	for (path_it_init(&it, clt);
-	     (sess = it.next_path(&it)) && it.i < it.clt->paths_num; it.i++) {
-		if (READ_ONCE(sess->state) != RTRS_CLT_CONNECTED)
+	     (clt_path = it.next_path(&it)) && it.i < it.clt->paths_num; it.i++) {
+		if (READ_ONCE(clt_path->state) != RTRS_CLT_CONNECTED)
 			continue;
 
-		if (usr_len + hdr_len > sess->max_hdr_size) {
-			rtrs_wrn_rl(sess->clt,
+		if (usr_len + hdr_len > clt_path->max_hdr_size) {
+			rtrs_wrn_rl(clt_path->clt,
 				     "%s request failed, user message size is %zu and header length %zu, but max size is %u\n",
 				     dir == READ ? "Read" : "Write",
-				     usr_len, hdr_len, sess->max_hdr_size);
+				     usr_len, hdr_len, clt_path->max_hdr_size);
 			err = -EMSGSIZE;
 			break;
 		}
-		req = rtrs_clt_get_req(sess, ops->conf_fn, permit, ops->priv,
+		req = rtrs_clt_get_req(clt_path, ops->conf_fn, permit, ops->priv,
 				       vec, usr_len, sg, sg_cnt, data_len,
 				       dma_dir);
 		if (dir == READ)
@@ -3027,16 +3048,16 @@
 	/* If no path, return -1 for block layer not to try again */
 	int cnt = -1;
 	struct rtrs_con *con;
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	struct path_it it;
 
 	rcu_read_lock();
 	for (path_it_init(&it, clt);
-	     (sess = it.next_path(&it)) && it.i < it.clt->paths_num; it.i++) {
-		if (READ_ONCE(sess->state) != RTRS_CLT_CONNECTED)
+	     (clt_path = it.next_path(&it)) && it.i < it.clt->paths_num; it.i++) {
+		if (READ_ONCE(clt_path->state) != RTRS_CLT_CONNECTED)
 			continue;
 
-		con = sess->s.con[index + 1];
+		con = clt_path->s.con[index + 1];
 		cnt = ib_process_cq_direct(con->cq, -1);
 		if (cnt)
 			break;
@@ -3074,12 +3095,12 @@
 int rtrs_clt_create_path_from_sysfs(struct rtrs_clt *clt,
 				     struct rtrs_addr *addr)
 {
-	struct rtrs_clt_sess *sess;
+	struct rtrs_clt_path *clt_path;
 	int err;
 
-	sess = alloc_sess(clt, addr, nr_cpu_ids, 0);
-	if (IS_ERR(sess))
-		return PTR_ERR(sess);
+	clt_path = alloc_path(clt, addr, nr_cpu_ids, 0);
+	if (IS_ERR(clt_path))
+		return PTR_ERR(clt_path);
 
 	mutex_lock(&clt->paths_mutex);
 	if (clt->paths_num == 0) {
@@ -3088,7 +3109,7 @@
 		 * the addition of the first path is like a new session for
 		 * the storage server
 		 */
-		sess->for_new_clt = 1;
+		clt_path->for_new_clt = 1;
 	}
 
 	mutex_unlock(&clt->paths_mutex);
@@ -3098,24 +3119,24 @@
 	 * IO will never grab it.  Also it is very important to add
 	 * path before init, since init fires LINK_CONNECTED event.
 	 */
-	rtrs_clt_add_path_to_arr(sess);
+	rtrs_clt_add_path_to_arr(clt_path);
 
-	err = init_sess(sess);
+	err = init_path(clt_path);
 	if (err)
-		goto close_sess;
+		goto close_path;
 
-	err = rtrs_clt_create_sess_files(sess);
+	err = rtrs_clt_create_path_files(clt_path);
 	if (err)
-		goto close_sess;
+		goto close_path;
 
 	return 0;
 
-close_sess:
-	rtrs_clt_remove_path_from_arr(sess);
-	rtrs_clt_close_conns(sess, true);
-	free_percpu(sess->stats->pcpu_stats);
-	kfree(sess->stats);
-	free_sess(sess);
+close_path:
+	rtrs_clt_remove_path_from_arr(clt_path);
+	rtrs_clt_close_conns(clt_path, true);
+	free_percpu(clt_path->stats->pcpu_stats);
+	kfree(clt_path->stats);
+	free_path(clt_path);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-clt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-clt.h
@@ -124,8 +124,8 @@
 	u32 rkey;
 };
 
-struct rtrs_clt_sess {
-	struct rtrs_sess	s;
+struct rtrs_clt_path {
+	struct rtrs_path	s;
 	struct rtrs_clt	*clt;
 	wait_queue_head_t	state_wq;
 	enum rtrs_clt_state	state;
@@ -156,7 +156,7 @@
 struct rtrs_clt {
 	struct list_head	paths_list; /* rcu protected list */
 	size_t			paths_num;
-	struct rtrs_clt_sess
+	struct rtrs_clt_path
 	__rcu * __percpu	*pcpu_path;
 	uuid_t			paths_uuid;
 	int			paths_up;
@@ -186,9 +186,9 @@
 	return container_of(c, struct rtrs_clt_con, c);
 }
 
-static inline struct rtrs_clt_sess *to_clt_sess(struct rtrs_sess *s)
+static inline struct rtrs_clt_path *to_clt_path(struct rtrs_path *s)
 {
-	return container_of(s, struct rtrs_clt_sess, s);
+	return container_of(s, struct rtrs_clt_path, s);
 }
 
 static inline int permit_size(struct rtrs_clt *clt)
@@ -201,16 +201,16 @@
 	return (struct rtrs_permit *)(clt->permits + permit_size(clt) * idx);
 }
 
-int rtrs_clt_reconnect_from_sysfs(struct rtrs_clt_sess *sess);
-void rtrs_clt_close_conns(struct rtrs_clt_sess *sess, bool wait);
+int rtrs_clt_reconnect_from_sysfs(struct rtrs_clt_path *path);
+void rtrs_clt_close_conns(struct rtrs_clt_path *clt_path, bool wait);
 int rtrs_clt_create_path_from_sysfs(struct rtrs_clt *clt,
 				     struct rtrs_addr *addr);
-int rtrs_clt_remove_path_from_sysfs(struct rtrs_clt_sess *sess,
+int rtrs_clt_remove_path_from_sysfs(struct rtrs_clt_path *path,
 				     const struct attribute *sysfs_self);
 
 void rtrs_clt_set_max_reconnect_attempts(struct rtrs_clt *clt, int value);
 int rtrs_clt_get_max_reconnect_attempts(const struct rtrs_clt *clt);
-void free_sess(struct rtrs_clt_sess *sess);
+void free_path(struct rtrs_clt_path *clt_path);
 
 /* rtrs-clt-stats.c */
 
@@ -243,8 +243,8 @@
 int rtrs_clt_create_sysfs_root_files(struct rtrs_clt *clt);
 void rtrs_clt_destroy_sysfs_root(struct rtrs_clt *clt);
 
-int rtrs_clt_create_sess_files(struct rtrs_clt_sess *sess);
-void rtrs_clt_destroy_sess_files(struct rtrs_clt_sess *sess,
+int rtrs_clt_create_path_files(struct rtrs_clt_path *clt_path);
+void rtrs_clt_destroy_path_files(struct rtrs_clt_path *clt_path,
 				  const struct attribute *sysfs_self);
 
 #endif /* RTRS_CLT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-pri.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-pri.h
@@ -23,6 +23,17 @@
 #define RTRS_PROTO_VER_STRING __stringify(RTRS_PROTO_VER_MAJOR) "." \
 			       __stringify(RTRS_PROTO_VER_MINOR)
 
+/*
+ * Max IB immediate data size is 2^28 (MAX_IMM_PAYL_BITS)
+ * and the minimum chunk size is 4096 (2^12).
+ * So the maximum sess_queue_depth is 65536 (2^16) in theory.
+ * But mempool_create, create_qp and ib_post_send fail with
+ * "cannot allocate memory" error if sess_queue_depth is too big.
+ * Therefore the pratical max value of sess_queue_depth is
+ * somewhere between 1 and 65534 and it depends on the system.
+ */
+#define MAX_SESS_QUEUE_DEPTH 65535
+
 enum rtrs_imm_const {
 	MAX_IMM_TYPE_BITS = 4,
 	MAX_IMM_TYPE_MASK = ((1 << MAX_IMM_TYPE_BITS) - 1),
@@ -46,16 +57,6 @@
 
 	MAX_PATHS_NUM = 128,
 
-	/*
-	 * Max IB immediate data size is 2^28 (MAX_IMM_PAYL_BITS)
-	 * and the minimum chunk size is 4096 (2^12).
-	 * So the maximum sess_queue_depth is 65536 (2^16) in theory.
-	 * But mempool_create, create_qp and ib_post_send fail with
-	 * "cannot allocate memory" error if sess_queue_depth is too big.
-	 * Therefore the pratical max value of sess_queue_depth is
-	 * somewhere between 1 and 65534 and it depends on the system.
-	 */
-	MAX_SESS_QUEUE_DEPTH = 65535,
 	MIN_CHUNK_SIZE = 8192,
 
 	RTRS_HB_INTERVAL_MS = 5000,
@@ -90,7 +91,7 @@
 };
 
 struct rtrs_con {
-	struct rtrs_sess	*sess;
+	struct rtrs_path	*path;
 	struct ib_qp		*qp;
 	struct ib_cq		*cq;
 	struct rdma_cm_id	*cm_id;
@@ -100,7 +101,7 @@
 	atomic_t		sq_wr_avail;
 };
 
-struct rtrs_sess {
+struct rtrs_path {
 	struct list_head	entry;
 	struct sockaddr_storage dst_addr;
 	struct sockaddr_storage src_addr;
@@ -229,11 +230,11 @@
 /**
  * struct rtrs_msg_info_req
  * @type:		@RTRS_MSG_INFO_REQ
- * @sessname:		Session name chosen by client
+ * @pathname:		Path name chosen by client
  */
 struct rtrs_msg_info_req {
 	__le16		type;
-	u8		sessname[NAME_MAX];
+	u8		pathname[NAME_MAX];
 	u8		reserved[15];
 };
 
@@ -313,19 +314,19 @@
 
 int rtrs_post_recv_empty(struct rtrs_con *con, struct ib_cqe *cqe);
 
-int rtrs_cq_qp_create(struct rtrs_sess *sess, struct rtrs_con *con,
+int rtrs_cq_qp_create(struct rtrs_path *path, struct rtrs_con *con,
 		      u32 max_send_sge, int cq_vector, int nr_cqe,
 		      u32 max_send_wr, u32 max_recv_wr,
 		      enum ib_poll_context poll_ctx);
 void rtrs_cq_qp_destroy(struct rtrs_con *con);
 
-void rtrs_init_hb(struct rtrs_sess *sess, struct ib_cqe *cqe,
+void rtrs_init_hb(struct rtrs_path *path, struct ib_cqe *cqe,
 		  unsigned int interval_ms, unsigned int missed_max,
 		  void (*err_handler)(struct rtrs_con *con),
 		  struct workqueue_struct *wq);
-void rtrs_start_hb(struct rtrs_sess *sess);
-void rtrs_stop_hb(struct rtrs_sess *sess);
-void rtrs_send_hb_ack(struct rtrs_sess *sess);
+void rtrs_start_hb(struct rtrs_path *path);
+void rtrs_stop_hb(struct rtrs_path *path);
+void rtrs_send_hb_ack(struct rtrs_path *path);
 
 void rtrs_rdma_dev_pd_init(enum ib_pd_flags pd_flags,
 			   struct rtrs_rdma_dev_pd *pool);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-srv-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-srv-sysfs.c
@@ -15,10 +15,10 @@
 
 static void rtrs_srv_release(struct kobject *kobj)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 
-	sess = container_of(kobj, struct rtrs_srv_sess, kobj);
-	kfree(sess);
+	srv_path = container_of(kobj, struct rtrs_srv_path, kobj);
+	kfree(srv_path);
 }
 
 static struct kobj_type ktype = {
@@ -36,24 +36,25 @@
 					  struct kobj_attribute *attr,
 					  const char *buf, size_t count)
 {
-	struct rtrs_srv_sess *sess;
-	struct rtrs_sess *s;
+	struct rtrs_srv_path *srv_path;
+	struct rtrs_path *s;
 	char str[MAXHOSTNAMELEN];
 
-	sess = container_of(kobj, struct rtrs_srv_sess, kobj);
-	s = &sess->s;
+	srv_path = container_of(kobj, struct rtrs_srv_path, kobj);
+	s = &srv_path->s;
 	if (!sysfs_streq(buf, "1")) {
 		rtrs_err(s, "%s: invalid value: '%s'\n",
 			  attr->attr.name, buf);
 		return -EINVAL;
 	}
 
-	sockaddr_to_str((struct sockaddr *)&sess->s.dst_addr, str, sizeof(str));
+	sockaddr_to_str((struct sockaddr *)&srv_path->s.dst_addr, str,
+			sizeof(str));
 
 	rtrs_info(s, "disconnect for path %s requested\n", str);
 	/* first remove sysfs itself to avoid deadlock */
-	sysfs_remove_file_self(&sess->kobj, &attr->attr);
-	close_sess(sess);
+	sysfs_remove_file_self(&srv_path->kobj, &attr->attr);
+	close_path(srv_path);
 
 	return count;
 }
@@ -66,11 +67,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	struct rtrs_con *usr_con;
 
-	sess = container_of(kobj, typeof(*sess), kobj);
-	usr_con = sess->s.con[0];
+	srv_path = container_of(kobj, typeof(*srv_path), kobj);
+	usr_con = srv_path->s.con[0];
 
 	return sysfs_emit(page, "%u\n", usr_con->cm_id->port_num);
 }
@@ -82,11 +83,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 
-	sess = container_of(kobj, struct rtrs_srv_sess, kobj);
+	srv_path = container_of(kobj, struct rtrs_srv_path, kobj);
 
-	return sysfs_emit(page, "%s\n", sess->s.dev->ib_dev->name);
+	return sysfs_emit(page, "%s\n", srv_path->s.dev->ib_dev->name);
 }
 
 static struct kobj_attribute rtrs_srv_hca_name_attr =
@@ -96,11 +97,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	int cnt;
 
-	sess = container_of(kobj, struct rtrs_srv_sess, kobj);
-	cnt = sockaddr_to_str((struct sockaddr *)&sess->s.dst_addr,
+	srv_path = container_of(kobj, struct rtrs_srv_path, kobj);
+	cnt = sockaddr_to_str((struct sockaddr *)&srv_path->s.dst_addr,
 			      page, PAGE_SIZE);
 	return cnt + scnprintf(page + cnt, PAGE_SIZE - cnt, "\n");
 }
@@ -112,11 +113,11 @@
 				       struct kobj_attribute *attr,
 				       char *page)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	int len;
 
-	sess = container_of(kobj, struct rtrs_srv_sess, kobj);
-	len = sockaddr_to_str((struct sockaddr *)&sess->s.src_addr, page,
+	srv_path = container_of(kobj, struct rtrs_srv_path, kobj);
+	len = sockaddr_to_str((struct sockaddr *)&srv_path->s.src_addr, page,
 			      PAGE_SIZE);
 	len += sysfs_emit_at(page, len, "\n");
 	return len;
@@ -125,7 +126,7 @@
 static struct kobj_attribute rtrs_srv_dst_addr_attr =
 	__ATTR(dst_addr, 0444, rtrs_srv_dst_addr_show, NULL);
 
-static struct attribute *rtrs_srv_sess_attrs[] = {
+static struct attribute *rtrs_srv_path_attrs[] = {
 	&rtrs_srv_hca_name_attr.attr,
 	&rtrs_srv_hca_port_attr.attr,
 	&rtrs_srv_src_addr_attr.attr,
@@ -134,8 +135,8 @@
 	NULL,
 };
 
-static const struct attribute_group rtrs_srv_sess_attr_group = {
-	.attrs = rtrs_srv_sess_attrs,
+static const struct attribute_group rtrs_srv_path_attr_group = {
+	.attrs = rtrs_srv_path_attrs,
 };
 
 STAT_ATTR(struct rtrs_srv_stats, rdma,
@@ -151,9 +152,9 @@
 	.attrs = rtrs_srv_stats_attrs,
 };
 
-static int rtrs_srv_create_once_sysfs_root_folders(struct rtrs_srv_sess *sess)
+static int rtrs_srv_create_once_sysfs_root_folders(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 	int err = 0;
 
 	mutex_lock(&srv->paths_mutex);
@@ -164,7 +165,7 @@
 		goto unlock;
 	}
 	srv->dev.class = rtrs_dev_class;
-	err = dev_set_name(&srv->dev, "%s", sess->s.sessname);
+	err = dev_set_name(&srv->dev, "%s", srv_path->s.sessname);
 	if (err)
 		goto unlock;
 
@@ -196,9 +197,9 @@
 }
 
 static void
-rtrs_srv_destroy_once_sysfs_root_folders(struct rtrs_srv_sess *sess)
+rtrs_srv_destroy_once_sysfs_root_folders(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 
 	mutex_lock(&srv->paths_mutex);
 	if (!--srv->dev_ref) {
@@ -213,7 +214,7 @@
 	}
 }
 
-static void rtrs_srv_sess_stats_release(struct kobject *kobj)
+static void rtrs_srv_path_stats_release(struct kobject *kobj)
 {
 	struct rtrs_srv_stats *stats;
 
@@ -224,22 +225,22 @@
 
 static struct kobj_type ktype_stats = {
 	.sysfs_ops = &kobj_sysfs_ops,
-	.release = rtrs_srv_sess_stats_release,
+	.release = rtrs_srv_path_stats_release,
 };
 
-static int rtrs_srv_create_stats_files(struct rtrs_srv_sess *sess)
+static int rtrs_srv_create_stats_files(struct rtrs_srv_path *srv_path)
 {
 	int err;
-	struct rtrs_sess *s = &sess->s;
+	struct rtrs_path *s = &srv_path->s;
 
-	err = kobject_init_and_add(&sess->stats->kobj_stats, &ktype_stats,
-				   &sess->kobj, "stats");
+	err = kobject_init_and_add(&srv_path->stats->kobj_stats, &ktype_stats,
+				   &srv_path->kobj, "stats");
 	if (err) {
 		rtrs_err(s, "kobject_init_and_add(): %d\n", err);
-		kobject_put(&sess->stats->kobj_stats);
+		kobject_put(&srv_path->stats->kobj_stats);
 		return err;
 	}
-	err = sysfs_create_group(&sess->stats->kobj_stats,
+	err = sysfs_create_group(&srv_path->stats->kobj_stats,
 				 &rtrs_srv_stats_attr_group);
 	if (err) {
 		rtrs_err(s, "sysfs_create_group(): %d\n", err);
@@ -249,64 +250,64 @@
 	return 0;
 
 err:
-	kobject_del(&sess->stats->kobj_stats);
-	kobject_put(&sess->stats->kobj_stats);
+	kobject_del(&srv_path->stats->kobj_stats);
+	kobject_put(&srv_path->stats->kobj_stats);
 
 	return err;
 }
 
-int rtrs_srv_create_sess_files(struct rtrs_srv_sess *sess)
+int rtrs_srv_create_path_files(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
-	struct rtrs_sess *s = &sess->s;
+	struct rtrs_srv *srv = srv_path->srv;
+	struct rtrs_path *s = &srv_path->s;
 	char str[NAME_MAX];
 	int err;
 	struct rtrs_addr path = {
-		.src = &sess->s.dst_addr,
-		.dst = &sess->s.src_addr,
+		.src = &srv_path->s.dst_addr,
+		.dst = &srv_path->s.src_addr,
 	};
 
 	rtrs_addr_to_str(&path, str, sizeof(str));
-	err = rtrs_srv_create_once_sysfs_root_folders(sess);
+	err = rtrs_srv_create_once_sysfs_root_folders(srv_path);
 	if (err)
 		return err;
 
-	err = kobject_init_and_add(&sess->kobj, &ktype, srv->kobj_paths,
+	err = kobject_init_and_add(&srv_path->kobj, &ktype, srv->kobj_paths,
 				   "%s", str);
 	if (err) {
 		rtrs_err(s, "kobject_init_and_add(): %d\n", err);
 		goto destroy_root;
 	}
-	err = sysfs_create_group(&sess->kobj, &rtrs_srv_sess_attr_group);
+	err = sysfs_create_group(&srv_path->kobj, &rtrs_srv_path_attr_group);
 	if (err) {
 		rtrs_err(s, "sysfs_create_group(): %d\n", err);
 		goto put_kobj;
 	}
-	err = rtrs_srv_create_stats_files(sess);
+	err = rtrs_srv_create_stats_files(srv_path);
 	if (err)
 		goto remove_group;
 
 	return 0;
 
 remove_group:
-	sysfs_remove_group(&sess->kobj, &rtrs_srv_sess_attr_group);
+	sysfs_remove_group(&srv_path->kobj, &rtrs_srv_path_attr_group);
 put_kobj:
-	kobject_del(&sess->kobj);
+	kobject_del(&srv_path->kobj);
 destroy_root:
-	kobject_put(&sess->kobj);
-	rtrs_srv_destroy_once_sysfs_root_folders(sess);
+	kobject_put(&srv_path->kobj);
+	rtrs_srv_destroy_once_sysfs_root_folders(srv_path);
 
 	return err;
 }
 
-void rtrs_srv_destroy_sess_files(struct rtrs_srv_sess *sess)
+void rtrs_srv_destroy_path_files(struct rtrs_srv_path *srv_path)
 {
-	if (sess->kobj.state_in_sysfs) {
-		kobject_del(&sess->stats->kobj_stats);
-		kobject_put(&sess->stats->kobj_stats);
-		sysfs_remove_group(&sess->kobj, &rtrs_srv_sess_attr_group);
-		kobject_put(&sess->kobj);
+	if (srv_path->kobj.state_in_sysfs) {
+		kobject_del(&srv_path->stats->kobj_stats);
+		kobject_put(&srv_path->stats->kobj_stats);
+		sysfs_remove_group(&srv_path->kobj, &rtrs_srv_path_attr_group);
+		kobject_put(&srv_path->kobj);
 
-		rtrs_srv_destroy_once_sysfs_root_folders(sess);
+		rtrs_srv_destroy_once_sysfs_root_folders(srv_path);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-srv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-srv.c
@@ -62,19 +62,20 @@
 	return container_of(c, struct rtrs_srv_con, c);
 }
 
-static inline struct rtrs_srv_sess *to_srv_sess(struct rtrs_sess *s)
+static inline struct rtrs_srv_path *to_srv_path(struct rtrs_path *s)
 {
-	return container_of(s, struct rtrs_srv_sess, s);
+	return container_of(s, struct rtrs_srv_path, s);
 }
 
-static bool rtrs_srv_change_state(struct rtrs_srv_sess *sess,
+static bool rtrs_srv_change_state(struct rtrs_srv_path *srv_path,
 				  enum rtrs_srv_state new_state)
 {
 	enum rtrs_srv_state old_state;
 	bool changed = false;
+	unsigned long flags;
 
-	spin_lock_irq(&sess->state_lock);
-	old_state = sess->state;
+	spin_lock_irqsave(&srv_path->state_lock, flags);
+	old_state = srv_path->state;
 	switch (new_state) {
 	case RTRS_SRV_CONNECTED:
 		if (old_state == RTRS_SRV_CONNECTING)
@@ -93,8 +94,8 @@
 		break;
 	}
 	if (changed)
-		sess->state = new_state;
-	spin_unlock_irq(&sess->state_lock);
+		srv_path->state = new_state;
+	spin_unlock_irqrestore(&srv_path->state_lock, flags);
 
 	return changed;
 }
@@ -106,16 +107,16 @@
 	kfree(id);
 }
 
-static void rtrs_srv_free_ops_ids(struct rtrs_srv_sess *sess)
+static void rtrs_srv_free_ops_ids(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 	int i;
 
-	if (sess->ops_ids) {
+	if (srv_path->ops_ids) {
 		for (i = 0; i < srv->queue_depth; i++)
-			free_id(sess->ops_ids[i]);
-		kfree(sess->ops_ids);
-		sess->ops_ids = NULL;
+			free_id(srv_path->ops_ids[i]);
+		kfree(srv_path->ops_ids);
+		srv_path->ops_ids = NULL;
 	}
 }
 
@@ -127,21 +128,24 @@
 
 static inline void rtrs_srv_inflight_ref_release(struct percpu_ref *ref)
 {
-	struct rtrs_srv_sess *sess = container_of(ref, struct rtrs_srv_sess, ids_inflight_ref);
+	struct rtrs_srv_path *srv_path = container_of(ref,
+						      struct rtrs_srv_path,
+						      ids_inflight_ref);
 
-	percpu_ref_exit(&sess->ids_inflight_ref);
-	complete(&sess->complete_done);
+	percpu_ref_exit(&srv_path->ids_inflight_ref);
+	complete(&srv_path->complete_done);
 }
 
-static int rtrs_srv_alloc_ops_ids(struct rtrs_srv_sess *sess)
+static int rtrs_srv_alloc_ops_ids(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 	struct rtrs_srv_op *id;
 	int i, ret;
 
-	sess->ops_ids = kcalloc(srv->queue_depth, sizeof(*sess->ops_ids),
-				GFP_KERNEL);
-	if (!sess->ops_ids)
+	srv_path->ops_ids = kcalloc(srv->queue_depth,
+				    sizeof(*srv_path->ops_ids),
+				    GFP_KERNEL);
+	if (!srv_path->ops_ids)
 		goto err;
 
 	for (i = 0; i < srv->queue_depth; ++i) {
@@ -149,44 +153,44 @@
 		if (!id)
 			goto err;
 
-		sess->ops_ids[i] = id;
+		srv_path->ops_ids[i] = id;
 	}
 
-	ret = percpu_ref_init(&sess->ids_inflight_ref,
+	ret = percpu_ref_init(&srv_path->ids_inflight_ref,
 			      rtrs_srv_inflight_ref_release, 0, GFP_KERNEL);
 	if (ret) {
 		pr_err("Percpu reference init failed\n");
 		goto err;
 	}
-	init_completion(&sess->complete_done);
+	init_completion(&srv_path->complete_done);
 
 	return 0;
 
 err:
-	rtrs_srv_free_ops_ids(sess);
+	rtrs_srv_free_ops_ids(srv_path);
 	return -ENOMEM;
 }
 
-static inline void rtrs_srv_get_ops_ids(struct rtrs_srv_sess *sess)
+static inline void rtrs_srv_get_ops_ids(struct rtrs_srv_path *srv_path)
 {
-	percpu_ref_get(&sess->ids_inflight_ref);
+	percpu_ref_get(&srv_path->ids_inflight_ref);
 }
 
-static inline void rtrs_srv_put_ops_ids(struct rtrs_srv_sess *sess)
+static inline void rtrs_srv_put_ops_ids(struct rtrs_srv_path *srv_path)
 {
-	percpu_ref_put(&sess->ids_inflight_ref);
+	percpu_ref_put(&srv_path->ids_inflight_ref);
 }
 
 static void rtrs_srv_reg_mr_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_srv_con *con = to_srv_con(wc->qp->qp_context);
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 
 	if (wc->status != IB_WC_SUCCESS) {
 		rtrs_err(s, "REG MR failed: %s\n",
 			  ib_wc_status_msg(wc->status));
-		close_sess(sess);
+		close_path(srv_path);
 		return;
 	}
 }
@@ -197,9 +201,9 @@
 
 static int rdma_write_sg(struct rtrs_srv_op *id)
 {
-	struct rtrs_sess *s = id->con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
-	dma_addr_t dma_addr = sess->dma_addr[id->msg_id];
+	struct rtrs_path *s = id->con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
+	dma_addr_t dma_addr = srv_path->dma_addr[id->msg_id];
 	struct rtrs_srv_mr *srv_mr;
 	struct ib_send_wr inv_wr;
 	struct ib_rdma_wr imm_wr;
@@ -233,7 +237,7 @@
 		return -EINVAL;
 	}
 
-	plist->lkey = sess->s.dev->ib_pd->local_dma_lkey;
+	plist->lkey = srv_path->s.dev->ib_pd->local_dma_lkey;
 	offset += plist->length;
 
 	wr->wr.sg_list	= plist;
@@ -284,7 +288,7 @@
 	if (always_invalidate) {
 		struct rtrs_msg_rkey_rsp *msg;
 
-		srv_mr = &sess->mrs[id->msg_id];
+		srv_mr = &srv_path->mrs[id->msg_id];
 		rwr.wr.opcode = IB_WR_REG_MR;
 		rwr.wr.wr_cqe = &local_reg_cqe;
 		rwr.wr.num_sge = 0;
@@ -300,11 +304,11 @@
 
 		list.addr   = srv_mr->iu->dma_addr;
 		list.length = sizeof(*msg);
-		list.lkey   = sess->s.dev->ib_pd->local_dma_lkey;
+		list.lkey   = srv_path->s.dev->ib_pd->local_dma_lkey;
 		imm_wr.wr.sg_list = &list;
 		imm_wr.wr.num_sge = 1;
 		imm_wr.wr.opcode = IB_WR_SEND_WITH_IMM;
-		ib_dma_sync_single_for_device(sess->s.dev->ib_dev,
+		ib_dma_sync_single_for_device(srv_path->s.dev->ib_dev,
 					      srv_mr->iu->dma_addr,
 					      srv_mr->iu->size, DMA_TO_DEVICE);
 	} else {
@@ -317,7 +321,7 @@
 							     0, need_inval));
 
 	imm_wr.wr.wr_cqe   = &io_comp_cqe;
-	ib_dma_sync_single_for_device(sess->s.dev->ib_dev, dma_addr,
+	ib_dma_sync_single_for_device(srv_path->s.dev->ib_dev, dma_addr,
 				      offset, DMA_BIDIRECTIONAL);
 
 	err = ib_post_send(id->con->c.qp, &id->tx_wr.wr, NULL);
@@ -341,14 +345,15 @@
 static int send_io_resp_imm(struct rtrs_srv_con *con, struct rtrs_srv_op *id,
 			    int errno)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 	struct ib_send_wr inv_wr, *wr = NULL;
 	struct ib_rdma_wr imm_wr;
 	struct ib_reg_wr rwr;
 	struct rtrs_srv_mr *srv_mr;
 	bool need_inval = false;
 	enum ib_send_flags flags;
+	struct ib_sge list;
 	u32 imm;
 	int err;
 
@@ -399,10 +404,9 @@
 	imm = rtrs_to_io_rsp_imm(id->msg_id, errno, need_inval);
 	imm_wr.wr.next = NULL;
 	if (always_invalidate) {
-		struct ib_sge list;
 		struct rtrs_msg_rkey_rsp *msg;
 
-		srv_mr = &sess->mrs[id->msg_id];
+		srv_mr = &srv_path->mrs[id->msg_id];
 		rwr.wr.next = &imm_wr.wr;
 		rwr.wr.opcode = IB_WR_REG_MR;
 		rwr.wr.wr_cqe = &local_reg_cqe;
@@ -419,11 +423,11 @@
 
 		list.addr   = srv_mr->iu->dma_addr;
 		list.length = sizeof(*msg);
-		list.lkey   = sess->s.dev->ib_pd->local_dma_lkey;
+		list.lkey   = srv_path->s.dev->ib_pd->local_dma_lkey;
 		imm_wr.wr.sg_list = &list;
 		imm_wr.wr.num_sge = 1;
 		imm_wr.wr.opcode = IB_WR_SEND_WITH_IMM;
-		ib_dma_sync_single_for_device(sess->s.dev->ib_dev,
+		ib_dma_sync_single_for_device(srv_path->s.dev->ib_dev,
 					      srv_mr->iu->dma_addr,
 					      srv_mr->iu->size, DMA_TO_DEVICE);
 	} else {
@@ -444,11 +448,11 @@
 	return err;
 }
 
-void close_sess(struct rtrs_srv_sess *sess)
+void close_path(struct rtrs_srv_path *srv_path)
 {
-	if (rtrs_srv_change_state(sess, RTRS_SRV_CLOSING))
-		queue_work(rtrs_wq, &sess->close_work);
-	WARN_ON(sess->state != RTRS_SRV_CLOSING);
+	if (rtrs_srv_change_state(srv_path, RTRS_SRV_CLOSING))
+		queue_work(rtrs_wq, &srv_path->close_work);
+	WARN_ON(srv_path->state != RTRS_SRV_CLOSING);
 }
 
 static inline const char *rtrs_srv_state_str(enum rtrs_srv_state state)
@@ -480,35 +484,35 @@
  */
 bool rtrs_srv_resp_rdma(struct rtrs_srv_op *id, int status)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	struct rtrs_srv_con *con;
-	struct rtrs_sess *s;
+	struct rtrs_path *s;
 	int err;
 
 	if (WARN_ON(!id))
 		return true;
 
 	con = id->con;
-	s = con->c.sess;
-	sess = to_srv_sess(s);
+	s = con->c.path;
+	srv_path = to_srv_path(s);
 
 	id->status = status;
 
-	if (sess->state != RTRS_SRV_CONNECTED) {
+	if (srv_path->state != RTRS_SRV_CONNECTED) {
 		rtrs_err_rl(s,
-			    "Sending I/O response failed,  session %s is disconnected, sess state %s\n",
-			    kobject_name(&sess->kobj),
-			    rtrs_srv_state_str(sess->state));
+			    "Sending I/O response failed,  server path %s is disconnected, path state %s\n",
+			    kobject_name(&srv_path->kobj),
+			    rtrs_srv_state_str(srv_path->state));
 		goto out;
 	}
 	if (always_invalidate) {
-		struct rtrs_srv_mr *mr = &sess->mrs[id->msg_id];
+		struct rtrs_srv_mr *mr = &srv_path->mrs[id->msg_id];
 
 		ib_update_fast_reg_key(mr->mr, ib_inc_rkey(mr->mr->rkey));
 	}
 	if (atomic_sub_return(1, &con->c.sq_wr_avail) < 0) {
-		rtrs_err(s, "IB send queue full: sess=%s cid=%d\n",
-			 kobject_name(&sess->kobj),
+		rtrs_err(s, "IB send queue full: srv_path=%s cid=%d\n",
+			 kobject_name(&srv_path->kobj),
 			 con->c.cid);
 		atomic_add(1, &con->c.sq_wr_avail);
 		spin_lock(&con->rsp_wr_wait_lock);
@@ -523,12 +527,12 @@
 		err = rdma_write_sg(id);
 
 	if (err) {
-		rtrs_err_rl(s, "IO response failed: %d: sess=%s\n", err,
-			    kobject_name(&sess->kobj));
-		close_sess(sess);
+		rtrs_err_rl(s, "IO response failed: %d: srv_path=%s\n", err,
+			    kobject_name(&srv_path->kobj));
+		close_path(srv_path);
 	}
 out:
-	rtrs_srv_put_ops_ids(sess);
+	rtrs_srv_put_ops_ids(srv_path);
 	return true;
 }
 EXPORT_SYMBOL(rtrs_srv_resp_rdma);
@@ -544,27 +548,30 @@
 }
 EXPORT_SYMBOL(rtrs_srv_set_sess_priv);
 
-static void unmap_cont_bufs(struct rtrs_srv_sess *sess)
+static void unmap_cont_bufs(struct rtrs_srv_path *srv_path)
 {
 	int i;
 
-	for (i = 0; i < sess->mrs_num; i++) {
+	for (i = 0; i < srv_path->mrs_num; i++) {
 		struct rtrs_srv_mr *srv_mr;
 
-		srv_mr = &sess->mrs[i];
-		rtrs_iu_free(srv_mr->iu, sess->s.dev->ib_dev, 1);
+		srv_mr = &srv_path->mrs[i];
+
+		if (always_invalidate)
+			rtrs_iu_free(srv_mr->iu, srv_path->s.dev->ib_dev, 1);
+
 		ib_dereg_mr(srv_mr->mr);
-		ib_dma_unmap_sg(sess->s.dev->ib_dev, srv_mr->sgt.sgl,
+		ib_dma_unmap_sg(srv_path->s.dev->ib_dev, srv_mr->sgt.sgl,
 				srv_mr->sgt.nents, DMA_BIDIRECTIONAL);
 		sg_free_table(&srv_mr->sgt);
 	}
-	kfree(sess->mrs);
+	kfree(srv_path->mrs);
 }
 
-static int map_cont_bufs(struct rtrs_srv_sess *sess)
+static int map_cont_bufs(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
-	struct rtrs_sess *ss = &sess->s;
+	struct rtrs_srv *srv = srv_path->srv;
+	struct rtrs_path *ss = &srv_path->s;
 	int i, mri, err, mrs_num;
 	unsigned int chunk_bits;
 	int chunks_per_mr = 1;
@@ -581,23 +588,23 @@
 		mrs_num = srv->queue_depth;
 	} else {
 		chunks_per_mr =
-			sess->s.dev->ib_dev->attrs.max_fast_reg_page_list_len;
+			srv_path->s.dev->ib_dev->attrs.max_fast_reg_page_list_len;
 		mrs_num = DIV_ROUND_UP(srv->queue_depth, chunks_per_mr);
 		chunks_per_mr = DIV_ROUND_UP(srv->queue_depth, mrs_num);
 	}
 
-	sess->mrs = kcalloc(mrs_num, sizeof(*sess->mrs), GFP_KERNEL);
-	if (!sess->mrs)
+	srv_path->mrs = kcalloc(mrs_num, sizeof(*srv_path->mrs), GFP_KERNEL);
+	if (!srv_path->mrs)
 		return -ENOMEM;
 
-	sess->mrs_num = mrs_num;
+	srv_path->mrs_num = mrs_num;
 
 	for (mri = 0; mri < mrs_num; mri++) {
-		struct rtrs_srv_mr *srv_mr = &sess->mrs[mri];
+		struct rtrs_srv_mr *srv_mr = &srv_path->mrs[mri];
 		struct sg_table *sgt = &srv_mr->sgt;
 		struct scatterlist *s;
 		struct ib_mr *mr;
-		int nr, chunks;
+		int nr, nr_sgt, chunks;
 
 		chunks = chunks_per_mr * mri;
 		if (!always_invalidate)
@@ -612,19 +619,19 @@
 			sg_set_page(s, srv->chunks[chunks + i],
 				    max_chunk_size, 0);
 
-		nr = ib_dma_map_sg(sess->s.dev->ib_dev, sgt->sgl,
+		nr_sgt = ib_dma_map_sg(srv_path->s.dev->ib_dev, sgt->sgl,
 				   sgt->nents, DMA_BIDIRECTIONAL);
-		if (nr < sgt->nents) {
-			err = nr < 0 ? nr : -EINVAL;
+		if (!nr_sgt) {
+			err = -EINVAL;
 			goto free_sg;
 		}
-		mr = ib_alloc_mr(sess->s.dev->ib_pd, IB_MR_TYPE_MEM_REG,
-				 sgt->nents);
+		mr = ib_alloc_mr(srv_path->s.dev->ib_pd, IB_MR_TYPE_MEM_REG,
+				 nr_sgt);
 		if (IS_ERR(mr)) {
 			err = PTR_ERR(mr);
 			goto unmap_sg;
 		}
-		nr = ib_map_mr_sg(mr, sgt->sgl, sgt->nents,
+		nr = ib_map_mr_sg(mr, sgt->sgl, nr_sgt,
 				  NULL, max_chunk_size);
 		if (nr < 0 || nr < sgt->nents) {
 			err = nr < 0 ? nr : -EINVAL;
@@ -634,7 +641,7 @@
 		if (always_invalidate) {
 			srv_mr->iu = rtrs_iu_alloc(1,
 					sizeof(struct rtrs_msg_rkey_rsp),
-					GFP_KERNEL, sess->s.dev->ib_dev,
+					GFP_KERNEL, srv_path->s.dev->ib_dev,
 					DMA_TO_DEVICE, rtrs_srv_rdma_done);
 			if (!srv_mr->iu) {
 				err = -ENOMEM;
@@ -643,8 +650,8 @@
 			}
 		}
 		/* Eventually dma addr for each chunk can be cached */
-		for_each_sg(sgt->sgl, s, sgt->orig_nents, i)
-			sess->dma_addr[chunks + i] = sg_dma_address(s);
+		for_each_sg(sgt->sgl, s, nr_sgt, i)
+			srv_path->dma_addr[chunks + i] = sg_dma_address(s);
 
 		ib_update_fast_reg_key(mr, ib_inc_rkey(mr->rkey));
 		srv_mr->mr = mr;
@@ -652,97 +659,100 @@
 		continue;
 err:
 		while (mri--) {
-			srv_mr = &sess->mrs[mri];
+			srv_mr = &srv_path->mrs[mri];
 			sgt = &srv_mr->sgt;
 			mr = srv_mr->mr;
-			rtrs_iu_free(srv_mr->iu, sess->s.dev->ib_dev, 1);
+			rtrs_iu_free(srv_mr->iu, srv_path->s.dev->ib_dev, 1);
 dereg_mr:
 			ib_dereg_mr(mr);
 unmap_sg:
-			ib_dma_unmap_sg(sess->s.dev->ib_dev, sgt->sgl,
+			ib_dma_unmap_sg(srv_path->s.dev->ib_dev, sgt->sgl,
 					sgt->nents, DMA_BIDIRECTIONAL);
 free_sg:
 			sg_free_table(sgt);
 		}
-		kfree(sess->mrs);
+		kfree(srv_path->mrs);
 
 		return err;
 	}
 
 	chunk_bits = ilog2(srv->queue_depth - 1) + 1;
-	sess->mem_bits = (MAX_IMM_PAYL_BITS - chunk_bits);
+	srv_path->mem_bits = (MAX_IMM_PAYL_BITS - chunk_bits);
 
 	return 0;
 }
 
 static void rtrs_srv_hb_err_handler(struct rtrs_con *c)
 {
-	close_sess(to_srv_sess(c->sess));
+	close_path(to_srv_path(c->path));
 }
 
-static void rtrs_srv_init_hb(struct rtrs_srv_sess *sess)
+static void rtrs_srv_init_hb(struct rtrs_srv_path *srv_path)
 {
-	rtrs_init_hb(&sess->s, &io_comp_cqe,
+	rtrs_init_hb(&srv_path->s, &io_comp_cqe,
 		      RTRS_HB_INTERVAL_MS,
 		      RTRS_HB_MISSED_MAX,
 		      rtrs_srv_hb_err_handler,
 		      rtrs_wq);
 }
 
-static void rtrs_srv_start_hb(struct rtrs_srv_sess *sess)
+static void rtrs_srv_start_hb(struct rtrs_srv_path *srv_path)
 {
-	rtrs_start_hb(&sess->s);
+	rtrs_start_hb(&srv_path->s);
 }
 
-static void rtrs_srv_stop_hb(struct rtrs_srv_sess *sess)
+static void rtrs_srv_stop_hb(struct rtrs_srv_path *srv_path)
 {
-	rtrs_stop_hb(&sess->s);
+	rtrs_stop_hb(&srv_path->s);
 }
 
 static void rtrs_srv_info_rsp_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_srv_con *con = to_srv_con(wc->qp->qp_context);
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 	struct rtrs_iu *iu;
 
 	iu = container_of(wc->wr_cqe, struct rtrs_iu, cqe);
-	rtrs_iu_free(iu, sess->s.dev->ib_dev, 1);
+	rtrs_iu_free(iu, srv_path->s.dev->ib_dev, 1);
 
 	if (wc->status != IB_WC_SUCCESS) {
 		rtrs_err(s, "Sess info response send failed: %s\n",
 			  ib_wc_status_msg(wc->status));
-		close_sess(sess);
+		close_path(srv_path);
 		return;
 	}
 	WARN_ON(wc->opcode != IB_WC_SEND);
 }
 
-static void rtrs_srv_sess_up(struct rtrs_srv_sess *sess)
+static int rtrs_srv_path_up(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 	struct rtrs_srv_ctx *ctx = srv->ctx;
-	int up;
+	int up, ret = 0;
 
 	mutex_lock(&srv->paths_ev_mutex);
 	up = ++srv->paths_up;
 	if (up == 1)
-		ctx->ops.link_ev(srv, RTRS_SRV_LINK_EV_CONNECTED, NULL);
+		ret = ctx->ops.link_ev(srv, RTRS_SRV_LINK_EV_CONNECTED, NULL);
 	mutex_unlock(&srv->paths_ev_mutex);
 
 	/* Mark session as established */
-	sess->established = true;
+	if (!ret)
+		srv_path->established = true;
+
+	return ret;
 }
 
-static void rtrs_srv_sess_down(struct rtrs_srv_sess *sess)
+static void rtrs_srv_path_down(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 	struct rtrs_srv_ctx *ctx = srv->ctx;
 
-	if (!sess->established)
+	if (!srv_path->established)
 		return;
 
-	sess->established = false;
+	srv_path->established = false;
 	mutex_lock(&srv->paths_ev_mutex);
 	WARN_ON(!srv->paths_up);
 	if (--srv->paths_up == 0)
@@ -750,11 +760,11 @@
 	mutex_unlock(&srv->paths_ev_mutex);
 }
 
-static bool exist_sessname(struct rtrs_srv_ctx *ctx,
-			   const char *sessname, const uuid_t *path_uuid)
+static bool exist_pathname(struct rtrs_srv_ctx *ctx,
+			   const char *pathname, const uuid_t *path_uuid)
 {
 	struct rtrs_srv *srv;
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	bool found = false;
 
 	mutex_lock(&ctx->srv_mutex);
@@ -767,9 +777,9 @@
 			continue;
 		}
 
-		list_for_each_entry(sess, &srv->paths_list, s.entry) {
-			if (strlen(sess->s.sessname) == strlen(sessname) &&
-			    !strcmp(sess->s.sessname, sessname)) {
+		list_for_each_entry(srv_path, &srv->paths_list, s.entry) {
+			if (strlen(srv_path->s.sessname) == strlen(pathname) &&
+			    !strcmp(srv_path->s.sessname, pathname)) {
 				found = true;
 				break;
 			}
@@ -782,14 +792,14 @@
 	return found;
 }
 
-static int post_recv_sess(struct rtrs_srv_sess *sess);
+static int post_recv_path(struct rtrs_srv_path *srv_path);
 static int rtrs_rdma_do_reject(struct rdma_cm_id *cm_id, int errno);
 
 static int process_info_req(struct rtrs_srv_con *con,
 			    struct rtrs_msg_info_req *msg)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 	struct ib_send_wr *reg_wr = NULL;
 	struct rtrs_msg_info_rsp *rsp;
 	struct rtrs_iu *tx_iu;
@@ -797,26 +807,32 @@
 	int mri, err;
 	size_t tx_sz;
 
-	err = post_recv_sess(sess);
+	err = post_recv_path(srv_path);
 	if (err) {
-		rtrs_err(s, "post_recv_sess(), err: %d\n", err);
+		rtrs_err(s, "post_recv_path(), err: %d\n", err);
 		return err;
 	}
 
-	if (exist_sessname(sess->srv->ctx,
-			   msg->sessname, &sess->srv->paths_uuid)) {
-		rtrs_err(s, "sessname is duplicated: %s\n", msg->sessname);
+	if (strchr(msg->pathname, '/') || strchr(msg->pathname, '.')) {
+		rtrs_err(s, "pathname cannot contain / and .\n");
+		return -EINVAL;
+	}
+
+	if (exist_pathname(srv_path->srv->ctx,
+			   msg->pathname, &srv_path->srv->paths_uuid)) {
+		rtrs_err(s, "pathname is duplicated: %s\n", msg->pathname);
 		return -EPERM;
 	}
-	strscpy(sess->s.sessname, msg->sessname, sizeof(sess->s.sessname));
+	strscpy(srv_path->s.sessname, msg->pathname,
+		sizeof(srv_path->s.sessname));
 
-	rwr = kcalloc(sess->mrs_num, sizeof(*rwr), GFP_KERNEL);
+	rwr = kcalloc(srv_path->mrs_num, sizeof(*rwr), GFP_KERNEL);
 	if (!rwr)
 		return -ENOMEM;
 
 	tx_sz  = sizeof(*rsp);
-	tx_sz += sizeof(rsp->desc[0]) * sess->mrs_num;
-	tx_iu = rtrs_iu_alloc(1, tx_sz, GFP_KERNEL, sess->s.dev->ib_dev,
+	tx_sz += sizeof(rsp->desc[0]) * srv_path->mrs_num;
+	tx_iu = rtrs_iu_alloc(1, tx_sz, GFP_KERNEL, srv_path->s.dev->ib_dev,
 			       DMA_TO_DEVICE, rtrs_srv_info_rsp_done);
 	if (!tx_iu) {
 		err = -ENOMEM;
@@ -825,10 +841,10 @@
 
 	rsp = tx_iu->buf;
 	rsp->type = cpu_to_le16(RTRS_MSG_INFO_RSP);
-	rsp->sg_cnt = cpu_to_le16(sess->mrs_num);
+	rsp->sg_cnt = cpu_to_le16(srv_path->mrs_num);
 
-	for (mri = 0; mri < sess->mrs_num; mri++) {
-		struct ib_mr *mr = sess->mrs[mri].mr;
+	for (mri = 0; mri < srv_path->mrs_num; mri++) {
+		struct ib_mr *mr = srv_path->mrs[mri].mr;
 
 		rsp->desc[mri].addr = cpu_to_le64(mr->iova);
 		rsp->desc[mri].key  = cpu_to_le32(mr->rkey);
@@ -849,13 +865,18 @@
 		reg_wr = &rwr[mri].wr;
 	}
 
-	err = rtrs_srv_create_sess_files(sess);
+	err = rtrs_srv_create_path_files(srv_path);
 	if (err)
 		goto iu_free;
-	kobject_get(&sess->kobj);
-	get_device(&sess->srv->dev);
-	rtrs_srv_change_state(sess, RTRS_SRV_CONNECTED);
-	rtrs_srv_start_hb(sess);
+	kobject_get(&srv_path->kobj);
+	get_device(&srv_path->srv->dev);
+	err = rtrs_srv_change_state(srv_path, RTRS_SRV_CONNECTED);
+	if (!err) {
+		rtrs_err(s, "rtrs_srv_change_state(), err: %d\n", err);
+		goto iu_free;
+	}
+
+	rtrs_srv_start_hb(srv_path);
 
 	/*
 	 * We do not account number of established connections at the current
@@ -863,9 +884,14 @@
 	 * all connections are successfully established.  Thus, simply notify
 	 * listener with a proper event if we are the first path.
 	 */
-	rtrs_srv_sess_up(sess);
+	err = rtrs_srv_path_up(srv_path);
+	if (err) {
+		rtrs_err(s, "rtrs_srv_path_up(), err: %d\n", err);
+		goto iu_free;
+	}
 
-	ib_dma_sync_single_for_device(sess->s.dev->ib_dev, tx_iu->dma_addr,
+	ib_dma_sync_single_for_device(srv_path->s.dev->ib_dev,
+				      tx_iu->dma_addr,
 				      tx_iu->size, DMA_TO_DEVICE);
 
 	/* Send info response */
@@ -873,7 +899,7 @@
 	if (err) {
 		rtrs_err(s, "rtrs_iu_post_send(), err: %d\n", err);
 iu_free:
-		rtrs_iu_free(tx_iu, sess->s.dev->ib_dev, 1);
+		rtrs_iu_free(tx_iu, srv_path->s.dev->ib_dev, 1);
 	}
 rwr_free:
 	kfree(rwr);
@@ -884,8 +910,8 @@
 static void rtrs_srv_info_req_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_srv_con *con = to_srv_con(wc->qp->qp_context);
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 	struct rtrs_msg_info_req *msg;
 	struct rtrs_iu *iu;
 	int err;
@@ -905,7 +931,7 @@
 			  wc->byte_len);
 		goto close;
 	}
-	ib_dma_sync_single_for_cpu(sess->s.dev->ib_dev, iu->dma_addr,
+	ib_dma_sync_single_for_cpu(srv_path->s.dev->ib_dev, iu->dma_addr,
 				   iu->size, DMA_FROM_DEVICE);
 	msg = iu->buf;
 	if (le16_to_cpu(msg->type) != RTRS_MSG_INFO_REQ) {
@@ -917,23 +943,22 @@
 	if (err)
 		goto close;
 
-out:
-	rtrs_iu_free(iu, sess->s.dev->ib_dev, 1);
+	rtrs_iu_free(iu, srv_path->s.dev->ib_dev, 1);
 	return;
 close:
-	close_sess(sess);
-	goto out;
+	rtrs_iu_free(iu, srv_path->s.dev->ib_dev, 1);
+	close_path(srv_path);
 }
 
 static int post_recv_info_req(struct rtrs_srv_con *con)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 	struct rtrs_iu *rx_iu;
 	int err;
 
 	rx_iu = rtrs_iu_alloc(1, sizeof(struct rtrs_msg_info_req),
-			       GFP_KERNEL, sess->s.dev->ib_dev,
+			       GFP_KERNEL, srv_path->s.dev->ib_dev,
 			       DMA_FROM_DEVICE, rtrs_srv_info_req_done);
 	if (!rx_iu)
 		return -ENOMEM;
@@ -941,7 +966,7 @@
 	err = rtrs_iu_post_recv(&con->c, rx_iu);
 	if (err) {
 		rtrs_err(s, "rtrs_iu_post_recv(), err: %d\n", err);
-		rtrs_iu_free(rx_iu, sess->s.dev->ib_dev, 1);
+		rtrs_iu_free(rx_iu, srv_path->s.dev->ib_dev, 1);
 		return err;
 	}
 
@@ -961,20 +986,30 @@
 	return 0;
 }
 
-static int post_recv_sess(struct rtrs_srv_sess *sess)
+static int post_recv_path(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
-	struct rtrs_sess *s = &sess->s;
+	struct rtrs_srv *srv = srv_path->srv;
+	struct rtrs_path *s = &srv_path->s;
 	size_t q_size;
 	int err, cid;
 
-	for (cid = 0; cid < sess->s.con_num; cid++) {
+	for (cid = 0; cid < srv_path->s.con_num; cid++) {
 		if (cid == 0)
 			q_size = SERVICE_CON_QUEUE_DEPTH;
 		else
 			q_size = srv->queue_depth;
+		if (srv_path->state != RTRS_SRV_CONNECTING) {
+			rtrs_err(s, "Path state invalid. state %s\n",
+				 rtrs_srv_state_str(srv_path->state));
+			return -EIO;
+		}
 
-		err = post_recv_io(to_srv_con(sess->s.con[cid]), q_size);
+		if (!srv_path->s.con[cid]) {
+			rtrs_err(s, "Conn not set for %d\n", cid);
+			return -EIO;
+		}
+
+		err = post_recv_io(to_srv_con(srv_path->s.con[cid]), q_size);
 		if (err) {
 			rtrs_err(s, "post_recv_io(), err: %d\n", err);
 			return err;
@@ -988,9 +1023,9 @@
 			 struct rtrs_msg_rdma_read *msg,
 			 u32 buf_id, u32 off)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
+	struct rtrs_srv *srv = srv_path->srv;
 	struct rtrs_srv_ctx *ctx = srv->ctx;
 	struct rtrs_srv_op *id;
 
@@ -998,10 +1033,10 @@
 	void *data;
 	int ret;
 
-	if (sess->state != RTRS_SRV_CONNECTED) {
+	if (srv_path->state != RTRS_SRV_CONNECTED) {
 		rtrs_err_rl(s,
 			     "Processing read request failed,  session is disconnected, sess state %s\n",
-			     rtrs_srv_state_str(sess->state));
+			     rtrs_srv_state_str(srv_path->state));
 		return;
 	}
 	if (msg->sg_cnt != 1 && msg->sg_cnt != 0) {
@@ -1009,9 +1044,9 @@
 			    "Processing read request failed, invalid message\n");
 		return;
 	}
-	rtrs_srv_get_ops_ids(sess);
-	rtrs_srv_update_rdma_stats(sess->stats, off, READ);
-	id = sess->ops_ids[buf_id];
+	rtrs_srv_get_ops_ids(srv_path);
+	rtrs_srv_update_rdma_stats(srv_path->stats, off, READ);
+	id = srv_path->ops_ids[buf_id];
 	id->con		= con;
 	id->dir		= READ;
 	id->msg_id	= buf_id;
@@ -1037,18 +1072,18 @@
 		rtrs_err_rl(s,
 			     "Sending err msg for failed RDMA-Write-Req failed, msg_id %d, err: %d\n",
 			     buf_id, ret);
-		close_sess(sess);
+		close_path(srv_path);
 	}
-	rtrs_srv_put_ops_ids(sess);
+	rtrs_srv_put_ops_ids(srv_path);
 }
 
 static void process_write(struct rtrs_srv_con *con,
 			  struct rtrs_msg_rdma_write *req,
 			  u32 buf_id, u32 off)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
+	struct rtrs_srv *srv = srv_path->srv;
 	struct rtrs_srv_ctx *ctx = srv->ctx;
 	struct rtrs_srv_op *id;
 
@@ -1056,15 +1091,15 @@
 	void *data;
 	int ret;
 
-	if (sess->state != RTRS_SRV_CONNECTED) {
+	if (srv_path->state != RTRS_SRV_CONNECTED) {
 		rtrs_err_rl(s,
 			     "Processing write request failed,  session is disconnected, sess state %s\n",
-			     rtrs_srv_state_str(sess->state));
+			     rtrs_srv_state_str(srv_path->state));
 		return;
 	}
-	rtrs_srv_get_ops_ids(sess);
-	rtrs_srv_update_rdma_stats(sess->stats, off, WRITE);
-	id = sess->ops_ids[buf_id];
+	rtrs_srv_get_ops_ids(srv_path);
+	rtrs_srv_update_rdma_stats(srv_path->stats, off, WRITE);
+	id = srv_path->ops_ids[buf_id];
 	id->con    = con;
 	id->dir    = WRITE;
 	id->msg_id = buf_id;
@@ -1089,20 +1124,21 @@
 		rtrs_err_rl(s,
 			     "Processing write request failed, sending I/O response failed, msg_id %d, err: %d\n",
 			     buf_id, ret);
-		close_sess(sess);
+		close_path(srv_path);
 	}
-	rtrs_srv_put_ops_ids(sess);
+	rtrs_srv_put_ops_ids(srv_path);
 }
 
 static void process_io_req(struct rtrs_srv_con *con, void *msg,
 			   u32 id, u32 off)
 {
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
 	struct rtrs_msg_rdma_hdr *hdr;
 	unsigned int type;
 
-	ib_dma_sync_single_for_cpu(sess->s.dev->ib_dev, sess->dma_addr[id],
+	ib_dma_sync_single_for_cpu(srv_path->s.dev->ib_dev,
+				   srv_path->dma_addr[id],
 				   max_chunk_size, DMA_BIDIRECTIONAL);
 	hdr = msg;
 	type = le16_to_cpu(hdr->type);
@@ -1124,7 +1160,7 @@
 	return;
 
 err:
-	close_sess(sess);
+	close_path(srv_path);
 }
 
 static void rtrs_srv_inv_rkey_done(struct ib_cq *cq, struct ib_wc *wc)
@@ -1132,16 +1168,16 @@
 	struct rtrs_srv_mr *mr =
 		container_of(wc->wr_cqe, typeof(*mr), inv_cqe);
 	struct rtrs_srv_con *con = to_srv_con(wc->qp->qp_context);
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
+	struct rtrs_srv *srv = srv_path->srv;
 	u32 msg_id, off;
 	void *data;
 
 	if (wc->status != IB_WC_SUCCESS) {
 		rtrs_err(s, "Failed IB_WR_LOCAL_INV: %s\n",
 			  ib_wc_status_msg(wc->status));
-		close_sess(sess);
+		close_path(srv_path);
 	}
 	msg_id = mr->msg_id;
 	off = mr->msg_off;
@@ -1189,9 +1225,9 @@
 static void rtrs_srv_rdma_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct rtrs_srv_con *con = to_srv_con(wc->qp->qp_context);
-	struct rtrs_sess *s = con->c.sess;
-	struct rtrs_srv_sess *sess = to_srv_sess(s);
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_path *s = con->c.path;
+	struct rtrs_srv_path *srv_path = to_srv_path(s);
+	struct rtrs_srv *srv = srv_path->srv;
 	u32 imm_type, imm_payload;
 	int err;
 
@@ -1201,7 +1237,7 @@
 				  "%s (wr_cqe: %p, type: %d, vendor_err: 0x%x, len: %u)\n",
 				  ib_wc_status_msg(wc->status), wc->wr_cqe,
 				  wc->opcode, wc->vendor_err, wc->byte_len);
-			close_sess(sess);
+			close_path(srv_path);
 		}
 		return;
 	}
@@ -1214,10 +1250,11 @@
 		 */
 		if (WARN_ON(wc->wr_cqe != &io_comp_cqe))
 			return;
+		srv_path->s.hb_missed_cnt = 0;
 		err = rtrs_post_recv_empty(&con->c, &io_comp_cqe);
 		if (err) {
 			rtrs_err(s, "rtrs_post_recv(), err: %d\n", err);
-			close_sess(sess);
+			close_path(srv_path);
 			break;
 		}
 		rtrs_from_imm(be32_to_cpu(wc->ex.imm_data),
@@ -1226,16 +1263,16 @@
 			u32 msg_id, off;
 			void *data;
 
-			msg_id = imm_payload >> sess->mem_bits;
-			off = imm_payload & ((1 << sess->mem_bits) - 1);
+			msg_id = imm_payload >> srv_path->mem_bits;
+			off = imm_payload & ((1 << srv_path->mem_bits) - 1);
 			if (msg_id >= srv->queue_depth || off >= max_chunk_size) {
 				rtrs_err(s, "Wrong msg_id %u, off %u\n",
 					  msg_id, off);
-				close_sess(sess);
+				close_path(srv_path);
 				return;
 			}
 			if (always_invalidate) {
-				struct rtrs_srv_mr *mr = &sess->mrs[msg_id];
+				struct rtrs_srv_mr *mr = &srv_path->mrs[msg_id];
 
 				mr->msg_off = off;
 				mr->msg_id = msg_id;
@@ -1243,7 +1280,7 @@
 				if (err) {
 					rtrs_err(s, "rtrs_post_recv(), err: %d\n",
 						  err);
-					close_sess(sess);
+					close_path(srv_path);
 					break;
 				}
 			} else {
@@ -1252,10 +1289,10 @@
 			}
 		} else if (imm_type == RTRS_HB_MSG_IMM) {
 			WARN_ON(con->c.cid);
-			rtrs_send_hb_ack(&sess->s);
+			rtrs_send_hb_ack(&srv_path->s);
 		} else if (imm_type == RTRS_HB_ACK_IMM) {
 			WARN_ON(con->c.cid);
-			sess->s.hb_missed_cnt = 0;
+			srv_path->s.hb_missed_cnt = 0;
 		} else {
 			rtrs_wrn(s, "Unknown IMM type %u\n", imm_type);
 		}
@@ -1279,22 +1316,23 @@
 }
 
 /**
- * rtrs_srv_get_sess_name() - Get rtrs_srv peer hostname.
+ * rtrs_srv_get_path_name() - Get rtrs_srv peer hostname.
  * @srv:	Session
- * @sessname:	Sessname buffer
+ * @pathname:	Pathname buffer
  * @len:	Length of sessname buffer
  */
-int rtrs_srv_get_sess_name(struct rtrs_srv *srv, char *sessname, size_t len)
+int rtrs_srv_get_path_name(struct rtrs_srv *srv, char *pathname,
+			   size_t len)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	int err = -ENOTCONN;
 
 	mutex_lock(&srv->paths_mutex);
-	list_for_each_entry(sess, &srv->paths_list, s.entry) {
-		if (sess->state != RTRS_SRV_CONNECTED)
+	list_for_each_entry(srv_path, &srv->paths_list, s.entry) {
+		if (srv_path->state != RTRS_SRV_CONNECTED)
 			continue;
-		strscpy(sessname, sess->s.sessname,
-		       min_t(size_t, sizeof(sess->s.sessname), len));
+		strscpy(pathname, srv_path->s.sessname,
+			min_t(size_t, sizeof(srv_path->s.sessname), len));
 		err = 0;
 		break;
 	}
@@ -1302,7 +1340,7 @@
 
 	return err;
 }
-EXPORT_SYMBOL(rtrs_srv_get_sess_name);
+EXPORT_SYMBOL(rtrs_srv_get_path_name);
 
 /**
  * rtrs_srv_get_queue_depth() - Get rtrs_srv qdepth.
@@ -1314,22 +1352,22 @@
 }
 EXPORT_SYMBOL(rtrs_srv_get_queue_depth);
 
-static int find_next_bit_ring(struct rtrs_srv_sess *sess)
+static int find_next_bit_ring(struct rtrs_srv_path *srv_path)
 {
-	struct ib_device *ib_dev = sess->s.dev->ib_dev;
+	struct ib_device *ib_dev = srv_path->s.dev->ib_dev;
 	int v;
 
-	v = cpumask_next(sess->cur_cq_vector, &cq_affinity_mask);
+	v = cpumask_next(srv_path->cur_cq_vector, &cq_affinity_mask);
 	if (v >= nr_cpu_ids || v >= ib_dev->num_comp_vectors)
 		v = cpumask_first(&cq_affinity_mask);
 	return v;
 }
 
-static int rtrs_srv_get_next_cq_vector(struct rtrs_srv_sess *sess)
+static int rtrs_srv_get_next_cq_vector(struct rtrs_srv_path *srv_path)
 {
-	sess->cur_cq_vector = find_next_bit_ring(sess);
+	srv_path->cur_cq_vector = find_next_bit_ring(srv_path);
 
-	return sess->cur_cq_vector;
+	return srv_path->cur_cq_vector;
 }
 
 static void rtrs_srv_dev_release(struct device *dev)
@@ -1434,22 +1472,22 @@
 }
 
 static void __add_path_to_srv(struct rtrs_srv *srv,
-			      struct rtrs_srv_sess *sess)
+			      struct rtrs_srv_path *srv_path)
 {
-	list_add_tail(&sess->s.entry, &srv->paths_list);
+	list_add_tail(&srv_path->s.entry, &srv->paths_list);
 	srv->paths_num++;
 	WARN_ON(srv->paths_num >= MAX_PATHS_NUM);
 }
 
-static void del_path_from_srv(struct rtrs_srv_sess *sess)
+static void del_path_from_srv(struct rtrs_srv_path *srv_path)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 
 	if (WARN_ON(!srv))
 		return;
 
 	mutex_lock(&srv->paths_mutex);
-	list_del(&sess->s.entry);
+	list_del(&srv_path->s.entry);
 	WARN_ON(!srv->paths_num);
 	srv->paths_num--;
 	mutex_unlock(&srv->paths_mutex);
@@ -1482,44 +1520,43 @@
 static bool __is_path_w_addr_exists(struct rtrs_srv *srv,
 				    struct rdma_addr *addr)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 
-	list_for_each_entry(sess, &srv->paths_list, s.entry)
-		if (!sockaddr_cmp((struct sockaddr *)&sess->s.dst_addr,
+	list_for_each_entry(srv_path, &srv->paths_list, s.entry)
+		if (!sockaddr_cmp((struct sockaddr *)&srv_path->s.dst_addr,
 				  (struct sockaddr *)&addr->dst_addr) &&
-		    !sockaddr_cmp((struct sockaddr *)&sess->s.src_addr,
+		    !sockaddr_cmp((struct sockaddr *)&srv_path->s.src_addr,
 				  (struct sockaddr *)&addr->src_addr))
 			return true;
 
 	return false;
 }
 
-static void free_sess(struct rtrs_srv_sess *sess)
+static void free_path(struct rtrs_srv_path *srv_path)
 {
-	if (sess->kobj.state_in_sysfs) {
-		kobject_del(&sess->kobj);
-		kobject_put(&sess->kobj);
+	if (srv_path->kobj.state_in_sysfs) {
+		kobject_del(&srv_path->kobj);
+		kobject_put(&srv_path->kobj);
 	} else {
-		kfree(sess->stats);
-		kfree(sess);
+		kfree(srv_path->stats);
+		kfree(srv_path);
 	}
 }
 
 static void rtrs_srv_close_work(struct work_struct *work)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	struct rtrs_srv_con *con;
 	int i;
 
-	sess = container_of(work, typeof(*sess), close_work);
+	srv_path = container_of(work, typeof(*srv_path), close_work);
 
-	rtrs_srv_destroy_sess_files(sess);
-	rtrs_srv_stop_hb(sess);
+	rtrs_srv_stop_hb(srv_path);
 
-	for (i = 0; i < sess->s.con_num; i++) {
-		if (!sess->s.con[i])
+	for (i = 0; i < srv_path->s.con_num; i++) {
+		if (!srv_path->s.con[i])
 			continue;
-		con = to_srv_con(sess->s.con[i]);
+		con = to_srv_con(srv_path->s.con[i]);
 		rdma_disconnect(con->c.cm_id);
 		ib_drain_qp(con->c.qp);
 	}
@@ -1528,41 +1565,43 @@
 	 * Degrade ref count to the usual model with a single shared
 	 * atomic_t counter
 	 */
-	percpu_ref_kill(&sess->ids_inflight_ref);
+	percpu_ref_kill(&srv_path->ids_inflight_ref);
 
 	/* Wait for all completion */
-	wait_for_completion(&sess->complete_done);
+	wait_for_completion(&srv_path->complete_done);
+
+	rtrs_srv_destroy_path_files(srv_path);
 
 	/* Notify upper layer if we are the last path */
-	rtrs_srv_sess_down(sess);
+	rtrs_srv_path_down(srv_path);
 
-	unmap_cont_bufs(sess);
-	rtrs_srv_free_ops_ids(sess);
+	unmap_cont_bufs(srv_path);
+	rtrs_srv_free_ops_ids(srv_path);
 
-	for (i = 0; i < sess->s.con_num; i++) {
-		if (!sess->s.con[i])
+	for (i = 0; i < srv_path->s.con_num; i++) {
+		if (!srv_path->s.con[i])
 			continue;
-		con = to_srv_con(sess->s.con[i]);
+		con = to_srv_con(srv_path->s.con[i]);
 		rtrs_cq_qp_destroy(&con->c);
 		rdma_destroy_id(con->c.cm_id);
 		kfree(con);
 	}
-	rtrs_ib_dev_put(sess->s.dev);
+	rtrs_ib_dev_put(srv_path->s.dev);
 
-	del_path_from_srv(sess);
-	put_srv(sess->srv);
-	sess->srv = NULL;
-	rtrs_srv_change_state(sess, RTRS_SRV_CLOSED);
+	del_path_from_srv(srv_path);
+	put_srv(srv_path->srv);
+	srv_path->srv = NULL;
+	rtrs_srv_change_state(srv_path, RTRS_SRV_CLOSED);
 
-	kfree(sess->dma_addr);
-	kfree(sess->s.con);
-	free_sess(sess);
+	kfree(srv_path->dma_addr);
+	kfree(srv_path->s.con);
+	free_path(srv_path);
 }
 
-static int rtrs_rdma_do_accept(struct rtrs_srv_sess *sess,
+static int rtrs_rdma_do_accept(struct rtrs_srv_path *srv_path,
 			       struct rdma_cm_id *cm_id)
 {
-	struct rtrs_srv *srv = sess->srv;
+	struct rtrs_srv *srv = srv_path->srv;
 	struct rtrs_msg_conn_rsp msg;
 	struct rdma_conn_param param;
 	int err;
@@ -1610,25 +1649,25 @@
 	return errno;
 }
 
-static struct rtrs_srv_sess *
-__find_sess(struct rtrs_srv *srv, const uuid_t *sess_uuid)
+static struct rtrs_srv_path *
+__find_path(struct rtrs_srv *srv, const uuid_t *sess_uuid)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 
-	list_for_each_entry(sess, &srv->paths_list, s.entry) {
-		if (uuid_equal(&sess->s.uuid, sess_uuid))
-			return sess;
+	list_for_each_entry(srv_path, &srv->paths_list, s.entry) {
+		if (uuid_equal(&srv_path->s.uuid, sess_uuid))
+			return srv_path;
 	}
 
 	return NULL;
 }
 
-static int create_con(struct rtrs_srv_sess *sess,
+static int create_con(struct rtrs_srv_path *srv_path,
 		      struct rdma_cm_id *cm_id,
 		      unsigned int cid)
 {
-	struct rtrs_srv *srv = sess->srv;
-	struct rtrs_sess *s = &sess->s;
+	struct rtrs_srv *srv = srv_path->srv;
+	struct rtrs_path *s = &srv_path->s;
 	struct rtrs_srv_con *con;
 
 	u32 cq_num, max_send_wr, max_recv_wr, wr_limit;
@@ -1643,10 +1682,10 @@
 	spin_lock_init(&con->rsp_wr_wait_lock);
 	INIT_LIST_HEAD(&con->rsp_wr_wait_list);
 	con->c.cm_id = cm_id;
-	con->c.sess = &sess->s;
+	con->c.path = &srv_path->s;
 	con->c.cid = cid;
 	atomic_set(&con->c.wr_cnt, 1);
-	wr_limit = sess->s.dev->ib_dev->attrs.max_qp_wr;
+	wr_limit = srv_path->s.dev->ib_dev->attrs.max_qp_wr;
 
 	if (con->c.cid == 0) {
 		/*
@@ -1679,10 +1718,10 @@
 	}
 	cq_num = max_send_wr + max_recv_wr;
 	atomic_set(&con->c.sq_wr_avail, max_send_wr);
-	cq_vector = rtrs_srv_get_next_cq_vector(sess);
+	cq_vector = rtrs_srv_get_next_cq_vector(srv_path);
 
 	/* TODO: SOFTIRQ can be faster, but be careful with softirq context */
-	err = rtrs_cq_qp_create(&sess->s, &con->c, 1, cq_vector, cq_num,
+	err = rtrs_cq_qp_create(&srv_path->s, &con->c, 1, cq_vector, cq_num,
 				 max_send_wr, max_recv_wr,
 				 IB_POLL_WORKQUEUE);
 	if (err) {
@@ -1694,8 +1733,8 @@
 		if (err)
 			goto free_cqqp;
 	}
-	WARN_ON(sess->s.con[cid]);
-	sess->s.con[cid] = &con->c;
+	WARN_ON(srv_path->s.con[cid]);
+	srv_path->s.con[cid] = &con->c;
 
 	/*
 	 * Change context from server to current connection.  The other
@@ -1714,13 +1753,13 @@
 	return err;
 }
 
-static struct rtrs_srv_sess *__alloc_sess(struct rtrs_srv *srv,
+static struct rtrs_srv_path *__alloc_path(struct rtrs_srv *srv,
 					   struct rdma_cm_id *cm_id,
 					   unsigned int con_num,
 					   unsigned int recon_cnt,
 					   const uuid_t *uuid)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	int err = -ENOMEM;
 	char str[NAME_MAX];
 	struct rtrs_addr path;
@@ -1734,73 +1773,76 @@
 		pr_err("Path with same addr exists\n");
 		goto err;
 	}
-	sess = kzalloc(sizeof(*sess), GFP_KERNEL);
-	if (!sess)
+	srv_path = kzalloc(sizeof(*srv_path), GFP_KERNEL);
+	if (!srv_path)
 		goto err;
 
-	sess->stats = kzalloc(sizeof(*sess->stats), GFP_KERNEL);
-	if (!sess->stats)
+	srv_path->stats = kzalloc(sizeof(*srv_path->stats), GFP_KERNEL);
+	if (!srv_path->stats)
 		goto err_free_sess;
 
-	sess->stats->sess = sess;
+	srv_path->stats->srv_path = srv_path;
 
-	sess->dma_addr = kcalloc(srv->queue_depth, sizeof(*sess->dma_addr),
-				 GFP_KERNEL);
-	if (!sess->dma_addr)
+	srv_path->dma_addr = kcalloc(srv->queue_depth,
+				     sizeof(*srv_path->dma_addr),
+				     GFP_KERNEL);
+	if (!srv_path->dma_addr)
 		goto err_free_stats;
 
-	sess->s.con = kcalloc(con_num, sizeof(*sess->s.con), GFP_KERNEL);
-	if (!sess->s.con)
+	srv_path->s.con = kcalloc(con_num, sizeof(*srv_path->s.con),
+				  GFP_KERNEL);
+	if (!srv_path->s.con)
 		goto err_free_dma_addr;
 
-	sess->state = RTRS_SRV_CONNECTING;
-	sess->srv = srv;
-	sess->cur_cq_vector = -1;
-	sess->s.dst_addr = cm_id->route.addr.dst_addr;
-	sess->s.src_addr = cm_id->route.addr.src_addr;
+	srv_path->state = RTRS_SRV_CONNECTING;
+	srv_path->srv = srv;
+	srv_path->cur_cq_vector = -1;
+	srv_path->s.dst_addr = cm_id->route.addr.dst_addr;
+	srv_path->s.src_addr = cm_id->route.addr.src_addr;
 
 	/* temporary until receiving session-name from client */
-	path.src = &sess->s.src_addr;
-	path.dst = &sess->s.dst_addr;
+	path.src = &srv_path->s.src_addr;
+	path.dst = &srv_path->s.dst_addr;
 	rtrs_addr_to_str(&path, str, sizeof(str));
-	strscpy(sess->s.sessname, str, sizeof(sess->s.sessname));
+	strscpy(srv_path->s.sessname, str, sizeof(srv_path->s.sessname));
 
-	sess->s.con_num = con_num;
-	sess->s.recon_cnt = recon_cnt;
-	uuid_copy(&sess->s.uuid, uuid);
-	spin_lock_init(&sess->state_lock);
-	INIT_WORK(&sess->close_work, rtrs_srv_close_work);
-	rtrs_srv_init_hb(sess);
+	srv_path->s.con_num = con_num;
+	srv_path->s.irq_con_num = con_num;
+	srv_path->s.recon_cnt = recon_cnt;
+	uuid_copy(&srv_path->s.uuid, uuid);
+	spin_lock_init(&srv_path->state_lock);
+	INIT_WORK(&srv_path->close_work, rtrs_srv_close_work);
+	rtrs_srv_init_hb(srv_path);
 
-	sess->s.dev = rtrs_ib_dev_find_or_add(cm_id->device, &dev_pd);
-	if (!sess->s.dev) {
+	srv_path->s.dev = rtrs_ib_dev_find_or_add(cm_id->device, &dev_pd);
+	if (!srv_path->s.dev) {
 		err = -ENOMEM;
 		goto err_free_con;
 	}
-	err = map_cont_bufs(sess);
+	err = map_cont_bufs(srv_path);
 	if (err)
 		goto err_put_dev;
 
-	err = rtrs_srv_alloc_ops_ids(sess);
+	err = rtrs_srv_alloc_ops_ids(srv_path);
 	if (err)
 		goto err_unmap_bufs;
 
-	__add_path_to_srv(srv, sess);
+	__add_path_to_srv(srv, srv_path);
 
-	return sess;
+	return srv_path;
 
 err_unmap_bufs:
-	unmap_cont_bufs(sess);
+	unmap_cont_bufs(srv_path);
 err_put_dev:
-	rtrs_ib_dev_put(sess->s.dev);
+	rtrs_ib_dev_put(srv_path->s.dev);
 err_free_con:
-	kfree(sess->s.con);
+	kfree(srv_path->s.con);
 err_free_dma_addr:
-	kfree(sess->dma_addr);
+	kfree(srv_path->dma_addr);
 err_free_stats:
-	kfree(sess->stats);
+	kfree(srv_path->stats);
 err_free_sess:
-	kfree(sess);
+	kfree(srv_path);
 err:
 	return ERR_PTR(err);
 }
@@ -1810,7 +1852,7 @@
 			      size_t len)
 {
 	struct rtrs_srv_ctx *ctx = cm_id->context;
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 	struct rtrs_srv *srv;
 
 	u16 version, con_num, cid;
@@ -1851,16 +1893,16 @@
 		goto reject_w_err;
 	}
 	mutex_lock(&srv->paths_mutex);
-	sess = __find_sess(srv, &msg->sess_uuid);
-	if (sess) {
-		struct rtrs_sess *s = &sess->s;
+	srv_path = __find_path(srv, &msg->sess_uuid);
+	if (srv_path) {
+		struct rtrs_path *s = &srv_path->s;
 
 		/* Session already holds a reference */
 		put_srv(srv);
 
-		if (sess->state != RTRS_SRV_CONNECTING) {
+		if (srv_path->state != RTRS_SRV_CONNECTING) {
 			rtrs_err(s, "Session in wrong state: %s\n",
-				  rtrs_srv_state_str(sess->state));
+				  rtrs_srv_state_str(srv_path->state));
 			mutex_unlock(&srv->paths_mutex);
 			goto reject_w_err;
 		}
@@ -1880,19 +1922,19 @@
 			goto reject_w_err;
 		}
 	} else {
-		sess = __alloc_sess(srv, cm_id, con_num, recon_cnt,
+		srv_path = __alloc_path(srv, cm_id, con_num, recon_cnt,
 				    &msg->sess_uuid);
-		if (IS_ERR(sess)) {
+		if (IS_ERR(srv_path)) {
 			mutex_unlock(&srv->paths_mutex);
 			put_srv(srv);
-			err = PTR_ERR(sess);
+			err = PTR_ERR(srv_path);
 			pr_err("RTRS server session allocation failed: %d\n", err);
 			goto reject_w_err;
 		}
 	}
-	err = create_con(sess, cm_id, cid);
+	err = create_con(srv_path, cm_id, cid);
 	if (err) {
-		rtrs_err((&sess->s), "create_con(), error %d\n", err);
+		rtrs_err((&srv_path->s), "create_con(), error %d\n", err);
 		rtrs_rdma_do_reject(cm_id, err);
 		/*
 		 * Since session has other connections we follow normal way
@@ -1901,9 +1943,9 @@
 		 */
 		goto close_and_return_err;
 	}
-	err = rtrs_rdma_do_accept(sess, cm_id);
+	err = rtrs_rdma_do_accept(srv_path, cm_id);
 	if (err) {
-		rtrs_err((&sess->s), "rtrs_rdma_do_accept(), error %d\n", err);
+		rtrs_err((&srv_path->s), "rtrs_rdma_do_accept(), error %d\n", err);
 		rtrs_rdma_do_reject(cm_id, err);
 		/*
 		 * Since current connection was successfully added to the
@@ -1923,7 +1965,7 @@
 
 close_and_return_err:
 	mutex_unlock(&srv->paths_mutex);
-	close_sess(sess);
+	close_path(srv_path);
 
 	return err;
 }
@@ -1931,14 +1973,14 @@
 static int rtrs_srv_rdma_cm_handler(struct rdma_cm_id *cm_id,
 				     struct rdma_cm_event *ev)
 {
-	struct rtrs_srv_sess *sess = NULL;
-	struct rtrs_sess *s = NULL;
+	struct rtrs_srv_path *srv_path = NULL;
+	struct rtrs_path *s = NULL;
 
 	if (ev->event != RDMA_CM_EVENT_CONNECT_REQUEST) {
 		struct rtrs_con *c = cm_id->context;
 
-		s = c->sess;
-		sess = to_srv_sess(s);
+		s = c->path;
+		srv_path = to_srv_path(s);
 	}
 
 	switch (ev->event) {
@@ -1962,7 +2004,7 @@
 	case RDMA_CM_EVENT_ADDR_CHANGE:
 	case RDMA_CM_EVENT_TIMEWAIT_EXIT:
 	case RDMA_CM_EVENT_DEVICE_REMOVAL:
-		close_sess(sess);
+		close_path(srv_path);
 		break;
 	default:
 		pr_err("Ignoring unexpected CM event %s, err %d\n",
@@ -2170,13 +2212,13 @@
 }
 EXPORT_SYMBOL(rtrs_srv_open);
 
-static void close_sessions(struct rtrs_srv *srv)
+static void close_paths(struct rtrs_srv *srv)
 {
-	struct rtrs_srv_sess *sess;
+	struct rtrs_srv_path *srv_path;
 
 	mutex_lock(&srv->paths_mutex);
-	list_for_each_entry(sess, &srv->paths_list, s.entry)
-		close_sess(sess);
+	list_for_each_entry(srv_path, &srv->paths_list, s.entry)
+		close_path(srv_path);
 	mutex_unlock(&srv->paths_mutex);
 }
 
@@ -2186,7 +2228,7 @@
 
 	mutex_lock(&ctx->srv_mutex);
 	list_for_each_entry(srv, &ctx->srv_list, ctx_list)
-		close_sessions(srv);
+		close_paths(srv);
 	mutex_unlock(&ctx->srv_mutex);
 	flush_workqueue(rtrs_wq);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs-srv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs-srv.h
@@ -37,7 +37,7 @@
 struct rtrs_srv_stats {
 	struct kobject				kobj_stats;
 	struct rtrs_srv_stats_rdma_stats	rdma_stats;
-	struct rtrs_srv_sess			*sess;
+	struct rtrs_srv_path			*srv_path;
 };
 
 struct rtrs_srv_con {
@@ -71,8 +71,8 @@
 	struct rtrs_iu	*iu;		/* send buffer for new rkey msg */
 };
 
-struct rtrs_srv_sess {
-	struct rtrs_sess	s;
+struct rtrs_srv_path {
+	struct rtrs_path	s;
 	struct rtrs_srv	*srv;
 	struct work_struct	close_work;
 	enum rtrs_srv_state	state;
@@ -125,7 +125,7 @@
 
 extern struct class *rtrs_dev_class;
 
-void close_sess(struct rtrs_srv_sess *sess);
+void close_path(struct rtrs_srv_path *srv_path);
 
 static inline void rtrs_srv_update_rdma_stats(struct rtrs_srv_stats *s,
 					      size_t size, int d)
@@ -143,7 +143,7 @@
 				 char *page, size_t len);
 
 /* functions which are implemented in rtrs-srv-sysfs.c */
-int rtrs_srv_create_sess_files(struct rtrs_srv_sess *sess);
-void rtrs_srv_destroy_sess_files(struct rtrs_srv_sess *sess);
+int rtrs_srv_create_path_files(struct rtrs_srv_path *srv_path);
+void rtrs_srv_destroy_path_files(struct rtrs_srv_path *srv_path);
 
 #endif /* RTRS_SRV_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs.c
@@ -37,8 +37,10 @@
 			goto err;
 
 		iu->dma_addr = ib_dma_map_single(dma_dev, iu->buf, size, dir);
-		if (ib_dma_mapping_error(dma_dev, iu->dma_addr))
+		if (ib_dma_mapping_error(dma_dev, iu->dma_addr)) {
+			kfree(iu->buf);
 			goto err;
+		}
 
 		iu->cqe.done  = done;
 		iu->size      = size;
@@ -69,16 +71,16 @@
 
 int rtrs_iu_post_recv(struct rtrs_con *con, struct rtrs_iu *iu)
 {
-	struct rtrs_sess *sess = con->sess;
+	struct rtrs_path *path = con->path;
 	struct ib_recv_wr wr;
 	struct ib_sge list;
 
 	list.addr   = iu->dma_addr;
 	list.length = iu->size;
-	list.lkey   = sess->dev->ib_pd->local_dma_lkey;
+	list.lkey   = path->dev->ib_pd->local_dma_lkey;
 
 	if (list.length == 0) {
-		rtrs_wrn(con->sess,
+		rtrs_wrn(con->path,
 			  "Posting receive work request failed, sg list is empty\n");
 		return -EINVAL;
 	}
@@ -126,7 +128,7 @@
 int rtrs_iu_post_send(struct rtrs_con *con, struct rtrs_iu *iu, size_t size,
 		       struct ib_send_wr *head)
 {
-	struct rtrs_sess *sess = con->sess;
+	struct rtrs_path *path = con->path;
 	struct ib_send_wr wr;
 	struct ib_sge list;
 
@@ -135,7 +137,7 @@
 
 	list.addr   = iu->dma_addr;
 	list.length = size;
-	list.lkey   = sess->dev->ib_pd->local_dma_lkey;
+	list.lkey   = path->dev->ib_pd->local_dma_lkey;
 
 	wr = (struct ib_send_wr) {
 		.wr_cqe     = &iu->cqe,
@@ -188,11 +190,11 @@
 					  struct ib_send_wr *head)
 {
 	struct ib_rdma_wr wr;
-	struct rtrs_sess *sess = con->sess;
+	struct rtrs_path *path = con->path;
 	enum ib_send_flags sflags;
 
 	atomic_dec_if_positive(&con->sq_wr_avail);
-	sflags = (atomic_inc_return(&con->wr_cnt) % sess->signal_interval) ?
+	sflags = (atomic_inc_return(&con->wr_cnt) % path->signal_interval) ?
 		0 : IB_SEND_SIGNALED;
 
 	wr = (struct ib_rdma_wr) {
@@ -211,26 +213,36 @@
 
 	switch (ev->event) {
 	case IB_EVENT_COMM_EST:
-		rtrs_info(con->sess, "QP event %s (%d) received\n",
+		rtrs_info(con->path, "QP event %s (%d) received\n",
 			   ib_event_msg(ev->event), ev->event);
 		rdma_notify(con->cm_id, IB_EVENT_COMM_EST);
 		break;
 	default:
-		rtrs_info(con->sess, "Unhandled QP event %s (%d) received\n",
+		rtrs_info(con->path, "Unhandled QP event %s (%d) received\n",
 			   ib_event_msg(ev->event), ev->event);
 		break;
 	}
 }
 
+static bool is_pollqueue(struct rtrs_con *con)
+{
+	return con->cid >= con->path->irq_con_num;
+}
+
 static int create_cq(struct rtrs_con *con, int cq_vector, int nr_cqe,
 		     enum ib_poll_context poll_ctx)
 {
 	struct rdma_cm_id *cm_id = con->cm_id;
 	struct ib_cq *cq;
 
-	cq = ib_cq_pool_get(cm_id->device, nr_cqe, cq_vector, poll_ctx);
+	if (is_pollqueue(con))
+		cq = ib_alloc_cq(cm_id->device, con, nr_cqe, cq_vector,
+				 poll_ctx);
+	else
+		cq = ib_cq_pool_get(cm_id->device, nr_cqe, cq_vector, poll_ctx);
+
 	if (IS_ERR(cq)) {
-		rtrs_err(con->sess, "Creating completion queue failed, errno: %ld\n",
+		rtrs_err(con->path, "Creating completion queue failed, errno: %ld\n",
 			  PTR_ERR(cq));
 		return PTR_ERR(cq);
 	}
@@ -243,7 +255,7 @@
 static int create_qp(struct rtrs_con *con, struct ib_pd *pd,
 		     u32 max_send_wr, u32 max_recv_wr, u32 max_sge)
 {
-	struct ib_qp_init_attr init_attr = {NULL};
+	struct ib_qp_init_attr init_attr = {};
 	struct rdma_cm_id *cm_id = con->cm_id;
 	int ret;
 
@@ -261,7 +273,7 @@
 
 	ret = rdma_create_qp(cm_id, pd, &init_attr);
 	if (ret) {
-		rtrs_err(con->sess, "Creating QP failed, err: %d\n", ret);
+		rtrs_err(con->path, "Creating QP failed, err: %d\n", ret);
 		return ret;
 	}
 	con->qp = cm_id->qp;
@@ -269,7 +281,18 @@
 	return ret;
 }
 
-int rtrs_cq_qp_create(struct rtrs_sess *sess, struct rtrs_con *con,
+static void destroy_cq(struct rtrs_con *con)
+{
+	if (con->cq) {
+		if (is_pollqueue(con))
+			ib_free_cq(con->cq);
+		else
+			ib_cq_pool_put(con->cq, con->nr_cqe);
+	}
+	con->cq = NULL;
+}
+
+int rtrs_cq_qp_create(struct rtrs_path *path, struct rtrs_con *con,
 		       u32 max_send_sge, int cq_vector, int nr_cqe,
 		       u32 max_send_wr, u32 max_recv_wr,
 		       enum ib_poll_context poll_ctx)
@@ -280,14 +303,13 @@
 	if (err)
 		return err;
 
-	err = create_qp(con, sess->dev->ib_pd, max_send_wr, max_recv_wr,
+	err = create_qp(con, path->dev->ib_pd, max_send_wr, max_recv_wr,
 			max_send_sge);
 	if (err) {
-		ib_cq_pool_put(con->cq, con->nr_cqe);
-		con->cq = NULL;
+		destroy_cq(con);
 		return err;
 	}
-	con->sess = sess;
+	con->path = path;
 
 	return 0;
 }
@@ -299,31 +321,28 @@
 		rdma_destroy_qp(con->cm_id);
 		con->qp = NULL;
 	}
-	if (con->cq) {
-		ib_cq_pool_put(con->cq, con->nr_cqe);
-		con->cq = NULL;
-	}
+	destroy_cq(con);
 }
 EXPORT_SYMBOL_GPL(rtrs_cq_qp_destroy);
 
-static void schedule_hb(struct rtrs_sess *sess)
+static void schedule_hb(struct rtrs_path *path)
 {
-	queue_delayed_work(sess->hb_wq, &sess->hb_dwork,
-			   msecs_to_jiffies(sess->hb_interval_ms));
+	queue_delayed_work(path->hb_wq, &path->hb_dwork,
+			   msecs_to_jiffies(path->hb_interval_ms));
 }
 
-void rtrs_send_hb_ack(struct rtrs_sess *sess)
+void rtrs_send_hb_ack(struct rtrs_path *path)
 {
-	struct rtrs_con *usr_con = sess->con[0];
+	struct rtrs_con *usr_con = path->con[0];
 	u32 imm;
 	int err;
 
 	imm = rtrs_to_imm(RTRS_HB_ACK_IMM, 0);
-	err = rtrs_post_rdma_write_imm_empty(usr_con, sess->hb_cqe, imm,
+	err = rtrs_post_rdma_write_imm_empty(usr_con, path->hb_cqe, imm,
 					     NULL);
 	if (err) {
-		rtrs_err(sess, "send HB ACK failed, errno: %d\n", err);
-		sess->hb_err_handler(usr_con);
+		rtrs_err(path, "send HB ACK failed, errno: %d\n", err);
+		path->hb_err_handler(usr_con);
 		return;
 	}
 }
@@ -332,63 +351,63 @@
 static void hb_work(struct work_struct *work)
 {
 	struct rtrs_con *usr_con;
-	struct rtrs_sess *sess;
+	struct rtrs_path *path;
 	u32 imm;
 	int err;
 
-	sess = container_of(to_delayed_work(work), typeof(*sess), hb_dwork);
-	usr_con = sess->con[0];
+	path = container_of(to_delayed_work(work), typeof(*path), hb_dwork);
+	usr_con = path->con[0];
 
-	if (sess->hb_missed_cnt > sess->hb_missed_max) {
-		rtrs_err(sess, "HB missed max reached.\n");
-		sess->hb_err_handler(usr_con);
+	if (path->hb_missed_cnt > path->hb_missed_max) {
+		rtrs_err(path, "HB missed max reached.\n");
+		path->hb_err_handler(usr_con);
 		return;
 	}
-	if (sess->hb_missed_cnt++) {
+	if (path->hb_missed_cnt++) {
 		/* Reschedule work without sending hb */
-		schedule_hb(sess);
+		schedule_hb(path);
 		return;
 	}
 
-	sess->hb_last_sent = ktime_get();
+	path->hb_last_sent = ktime_get();
 
 	imm = rtrs_to_imm(RTRS_HB_MSG_IMM, 0);
-	err = rtrs_post_rdma_write_imm_empty(usr_con, sess->hb_cqe, imm,
+	err = rtrs_post_rdma_write_imm_empty(usr_con, path->hb_cqe, imm,
 					     NULL);
 	if (err) {
-		rtrs_err(sess, "HB send failed, errno: %d\n", err);
-		sess->hb_err_handler(usr_con);
+		rtrs_err(path, "HB send failed, errno: %d\n", err);
+		path->hb_err_handler(usr_con);
 		return;
 	}
 
-	schedule_hb(sess);
+	schedule_hb(path);
 }
 
-void rtrs_init_hb(struct rtrs_sess *sess, struct ib_cqe *cqe,
+void rtrs_init_hb(struct rtrs_path *path, struct ib_cqe *cqe,
 		  unsigned int interval_ms, unsigned int missed_max,
 		  void (*err_handler)(struct rtrs_con *con),
 		  struct workqueue_struct *wq)
 {
-	sess->hb_cqe = cqe;
-	sess->hb_interval_ms = interval_ms;
-	sess->hb_err_handler = err_handler;
-	sess->hb_wq = wq;
-	sess->hb_missed_max = missed_max;
-	sess->hb_missed_cnt = 0;
-	INIT_DELAYED_WORK(&sess->hb_dwork, hb_work);
+	path->hb_cqe = cqe;
+	path->hb_interval_ms = interval_ms;
+	path->hb_err_handler = err_handler;
+	path->hb_wq = wq;
+	path->hb_missed_max = missed_max;
+	path->hb_missed_cnt = 0;
+	INIT_DELAYED_WORK(&path->hb_dwork, hb_work);
 }
 EXPORT_SYMBOL_GPL(rtrs_init_hb);
 
-void rtrs_start_hb(struct rtrs_sess *sess)
+void rtrs_start_hb(struct rtrs_path *path)
 {
-	schedule_hb(sess);
+	schedule_hb(path);
 }
 EXPORT_SYMBOL_GPL(rtrs_start_hb);
 
-void rtrs_stop_hb(struct rtrs_sess *sess)
+void rtrs_stop_hb(struct rtrs_path *path)
 {
-	cancel_delayed_work_sync(&sess->hb_dwork);
-	sess->hb_missed_cnt = 0;
+	cancel_delayed_work_sync(&path->hb_dwork);
+	path->hb_missed_cnt = 0;
 }
 EXPORT_SYMBOL_GPL(rtrs_stop_hb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/rtrs/rtrs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/rtrs/rtrs.h
@@ -53,13 +53,13 @@
 };
 
 struct rtrs_clt *rtrs_clt_open(struct rtrs_clt_ops *ops,
-				 const char *sessname,
+				 const char *pathname,
 				 const struct rtrs_addr *paths,
 				 size_t path_cnt, u16 port,
 				 size_t pdu_sz, u8 reconnect_delay_sec,
 				 s16 max_reconnect_attempts, u32 nr_poll_queues);
 
-void rtrs_clt_close(struct rtrs_clt *sess);
+void rtrs_clt_close(struct rtrs_clt *clt_path);
 
 enum wait_type {
 	RTRS_PERMIT_NOWAIT = 0,
@@ -175,7 +175,8 @@
 
 void rtrs_srv_set_sess_priv(struct rtrs_srv *sess, void *priv);
 
-int rtrs_srv_get_sess_name(struct rtrs_srv *sess, char *sessname, size_t len);
+int rtrs_srv_get_path_name(struct rtrs_srv *sess, char *pathname,
+			   size_t len);
 
 int rtrs_srv_get_queue_depth(struct rtrs_srv *sess);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/srp/ib_srp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/srp/ib_srp.c
@@ -1266,7 +1266,7 @@
 	if (scmnd) {
 		srp_free_req(ch, req, scmnd, 0);
 		scmnd->result = result;
-		scmnd->scsi_done(scmnd);
+		scsi_done(scmnd);
 	}
 }
 
@@ -1955,7 +1955,8 @@
 		if (scmnd) {
 			req = scsi_cmd_priv(scmnd);
 			scmnd = srp_claim_req(ch, req, NULL, scmnd);
-		} else {
+		}
+		if (!scmnd) {
 			shost_printk(KERN_ERR, target->scsi_host,
 				     "Null scmnd for RSP w/tag %#016llx received on ch %td / QP %#x\n",
 				     rsp->tag, ch - target->ch, ch->qp->qp_num);
@@ -1977,17 +1978,13 @@
 
 		if (unlikely(rsp->flags & SRP_RSP_FLAG_DIUNDER))
 			scsi_set_resid(scmnd, be32_to_cpu(rsp->data_in_res_cnt));
-		else if (unlikely(rsp->flags & SRP_RSP_FLAG_DIOVER))
-			scsi_set_resid(scmnd, -be32_to_cpu(rsp->data_in_res_cnt));
 		else if (unlikely(rsp->flags & SRP_RSP_FLAG_DOUNDER))
 			scsi_set_resid(scmnd, be32_to_cpu(rsp->data_out_res_cnt));
-		else if (unlikely(rsp->flags & SRP_RSP_FLAG_DOOVER))
-			scsi_set_resid(scmnd, -be32_to_cpu(rsp->data_out_res_cnt));
 
 		srp_free_req(ch, req, scmnd,
 			     be32_to_cpu(rsp->req_lim_delta));
 
-		scmnd->scsi_done(scmnd);
+		scsi_done(scmnd);
 	}
 }
 
@@ -2239,7 +2236,7 @@
 
 err:
 	if (scmnd->result) {
-		scmnd->scsi_done(scmnd);
+		scsi_done(scmnd);
 		ret = 0;
 	} else {
 		ret = SCSI_MLQUEUE_HOST_BUSY;
@@ -2782,16 +2779,13 @@
 static int srp_abort(struct scsi_cmnd *scmnd)
 {
 	struct srp_target_port *target = host_to_target(scmnd->device->host);
-	struct srp_request *req = (struct srp_request *) scmnd->host_scribble;
+	struct srp_request *req = scsi_cmd_priv(scmnd);
 	u32 tag;
 	u16 ch_idx;
 	struct srp_rdma_ch *ch;
-	int ret;
 
 	shost_printk(KERN_ERR, target->scsi_host, "SRP abort called\n");
 
-	if (!req)
-		return SUCCESS;
 	tag = blk_mq_unique_tag(scsi_cmd_to_rq(scmnd));
 	ch_idx = blk_mq_unique_tag_to_hwq(tag);
 	if (WARN_ON_ONCE(ch_idx >= target->ch_count))
@@ -2802,19 +2796,14 @@
 	shost_printk(KERN_ERR, target->scsi_host,
 		     "Sending SRP abort for tag %#x\n", tag);
 	if (srp_send_tsk_mgmt(ch, tag, scmnd->device->lun,
-			      SRP_TSK_ABORT_TASK, NULL) == 0)
-		ret = SUCCESS;
-	else if (target->rport->state == SRP_RPORT_LOST)
-		ret = FAST_IO_FAIL;
-	else
-		ret = FAILED;
-	if (ret == SUCCESS) {
+			      SRP_TSK_ABORT_TASK, NULL) == 0) {
 		srp_free_req(ch, req, scmnd, 0);
-		scmnd->result = DID_ABORT << 16;
-		scmnd->scsi_done(scmnd);
+		return SUCCESS;
 	}
+	if (target->rport->state == SRP_RPORT_LOST)
+		return FAST_IO_FAIL;
 
-	return ret;
+	return FAILED;
 }
 
 static int srp_reset_device(struct scsi_cmnd *scmnd)
@@ -3398,7 +3387,8 @@
 			break;
 
 		case SRP_OPT_PKEY:
-			if (match_hex(args, &token)) {
+			ret = match_hex(args, &token);
+			if (ret) {
 				pr_warn("bad P_Key parameter '%s'\n", p);
 				goto out;
 			}
@@ -3458,7 +3448,8 @@
 			break;
 
 		case SRP_OPT_MAX_SECT:
-			if (match_int(args, &token)) {
+			ret = match_int(args, &token);
+			if (ret) {
 				pr_warn("bad max sect parameter '%s'\n", p);
 				goto out;
 			}
@@ -3466,8 +3457,15 @@
 			break;
 
 		case SRP_OPT_QUEUE_SIZE:
-			if (match_int(args, &token) || token < 1) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for queue_size parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 1) {
 				pr_warn("bad queue_size parameter '%s'\n", p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->scsi_host->can_queue = token;
@@ -3478,25 +3476,40 @@
 			break;
 
 		case SRP_OPT_MAX_CMD_PER_LUN:
-			if (match_int(args, &token) || token < 1) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for max cmd_per_lun parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 1) {
 				pr_warn("bad max cmd_per_lun parameter '%s'\n",
 					p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->scsi_host->cmd_per_lun = token;
 			break;
 
 		case SRP_OPT_TARGET_CAN_QUEUE:
-			if (match_int(args, &token) || token < 1) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for max target_can_queue parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 1) {
 				pr_warn("bad max target_can_queue parameter '%s'\n",
 					p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->target_can_queue = token;
 			break;
 
 		case SRP_OPT_IO_CLASS:
-			if (match_hex(args, &token)) {
+			ret = match_hex(args, &token);
+			if (ret) {
 				pr_warn("bad IO class parameter '%s'\n", p);
 				goto out;
 			}
@@ -3505,6 +3518,7 @@
 				pr_warn("unknown IO class parameter value %x specified (use %x or %x).\n",
 					token, SRP_REV10_IB_IO_CLASS,
 					SRP_REV16A_IB_IO_CLASS);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->io_class = token;
@@ -3527,16 +3541,24 @@
 			break;
 
 		case SRP_OPT_CMD_SG_ENTRIES:
-			if (match_int(args, &token) || token < 1 || token > 255) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for max cmd_sg_entries parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 1 || token > 255) {
 				pr_warn("bad max cmd_sg_entries parameter '%s'\n",
 					p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->cmd_sg_cnt = token;
 			break;
 
 		case SRP_OPT_ALLOW_EXT_SG:
-			if (match_int(args, &token)) {
+			ret = match_int(args, &token);
+			if (ret) {
 				pr_warn("bad allow_ext_sg parameter '%s'\n", p);
 				goto out;
 			}
@@ -3544,43 +3566,77 @@
 			break;
 
 		case SRP_OPT_SG_TABLESIZE:
-			if (match_int(args, &token) || token < 1 ||
-					token > SG_MAX_SEGMENTS) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for max sg_tablesize parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 1 || token > SG_MAX_SEGMENTS) {
 				pr_warn("bad max sg_tablesize parameter '%s'\n",
 					p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->sg_tablesize = token;
 			break;
 
 		case SRP_OPT_COMP_VECTOR:
-			if (match_int(args, &token) || token < 0) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for comp_vector parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 0) {
 				pr_warn("bad comp_vector parameter '%s'\n", p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->comp_vector = token;
 			break;
 
 		case SRP_OPT_TL_RETRY_COUNT:
-			if (match_int(args, &token) || token < 2 || token > 7) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for tl_retry_count parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 2 || token > 7) {
 				pr_warn("bad tl_retry_count parameter '%s' (must be a number between 2 and 7)\n",
 					p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->tl_retry_count = token;
 			break;
 
 		case SRP_OPT_MAX_IT_IU_SIZE:
-			if (match_int(args, &token) || token < 0) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for max it_iu_size parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 0) {
 				pr_warn("bad maximum initiator to target IU size '%s'\n", p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->max_it_iu_size = token;
 			break;
 
 		case SRP_OPT_CH_COUNT:
-			if (match_int(args, &token) || token < 1) {
+			ret = match_int(args, &token);
+			if (ret) {
+				pr_warn("match_int() failed for channel count parameter '%s', Error %d\n",
+					p, ret);
+				goto out;
+			}
+			if (token < 1) {
 				pr_warn("bad channel count %s\n", p);
+				ret = -EINVAL;
 				goto out;
 			}
 			target->ch_count = token;
@@ -3589,6 +3645,7 @@
 		default:
 			pr_warn("unknown parameter or missing value '%s' in target creation request\n",
 				p);
+			ret = -EINVAL;
 			goto out;
 		}
 	}
@@ -4038,9 +4095,11 @@
 		spin_unlock(&host->target_lock);
 
 		/*
-		 * Wait for tl_err and target port removal tasks.
+		 * srp_queue_remove_work() queues a call to
+		 * srp_remove_target(). The latter function cancels
+		 * target->tl_err_work so waiting for the remove works to
+		 * finish is sufficient.
 		 */
-		flush_workqueue(system_long_wq);
 		flush_workqueue(srp_remove_wq);
 
 		kfree(host);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/srp/ib_srp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/srp/ib_srp.h
@@ -62,9 +62,6 @@
 	SRP_DEFAULT_CMD_SQ_SIZE = SRP_DEFAULT_QUEUE_SIZE - SRP_RSP_SQ_SIZE -
 				  SRP_TSK_MGMT_SQ_SIZE,
 
-	SRP_TAG_NO_REQ		= ~0U,
-	SRP_TAG_TSK_MGMT	= 1U << 31,
-
 	SRP_MAX_PAGES_PER_MR	= 512,
 
 	SRP_MAX_ADD_CDB_LEN	= 16,
@@ -79,6 +76,11 @@
 				  sizeof(struct srp_imm_buf),
 };
 
+enum {
+	SRP_TAG_NO_REQ		= ~0U,
+	SRP_TAG_TSK_MGMT	= BIT(31),
+};
+
 enum srp_target_state {
 	SRP_TARGET_SCANNING,
 	SRP_TARGET_LIVE,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/srpt/ib_srpt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/srpt/ib_srpt.c
@@ -79,12 +79,16 @@
 MODULE_PARM_DESC(srpt_srq_size,
 		 "Shared receive queue (SRQ) size.");
 
+static int srpt_set_u64_x(const char *buffer, const struct kernel_param *kp)
+{
+	return kstrtou64(buffer, 16, (u64 *)kp->arg);
+}
 static int srpt_get_u64_x(char *buffer, const struct kernel_param *kp)
 {
 	return sprintf(buffer, "0x%016llx\n", *(u64 *)kp->arg);
 }
-module_param_call(srpt_service_guid, NULL, srpt_get_u64_x, &srpt_service_guid,
-		  0444);
+module_param_call(srpt_service_guid, srpt_set_u64_x, srpt_get_u64_x,
+		  &srpt_service_guid, 0444);
 MODULE_PARM_DESC(srpt_service_guid,
 		 "Using this value for ioc_guid, id_ext, and cm_listen_id instead of using the node_guid of the first HCA.");
 
@@ -210,10 +214,12 @@
 /**
  * srpt_qp_event - QP event callback function
  * @event: Description of the event that occurred.
- * @ch: SRPT RDMA channel.
+ * @ptr: SRPT RDMA channel.
  */
-static void srpt_qp_event(struct ib_event *event, struct srpt_rdma_ch *ch)
+static void srpt_qp_event(struct ib_event *event, void *ptr)
 {
+	struct srpt_rdma_ch *ch = ptr;
+
 	pr_debug("QP event %d on ch=%p sess_name=%s-%d state=%s\n",
 		 event->event, ch, ch->sess_name, ch->qp->qp_num,
 		 get_ch_state_name(ch->state));
@@ -549,6 +555,7 @@
  */
 static int srpt_refresh_port(struct srpt_port *sport)
 {
+	struct ib_mad_agent *mad_agent;
 	struct ib_mad_reg_req reg_req;
 	struct ib_port_modify port_modify;
 	struct ib_port_attr port_attr;
@@ -565,12 +572,9 @@
 	if (ret)
 		return ret;
 
-	sport->port_guid_id.wwn.priv = sport;
-	srpt_format_guid(sport->port_guid_id.name,
-			 sizeof(sport->port_guid_id.name),
+	srpt_format_guid(sport->guid_name, ARRAY_SIZE(sport->guid_name),
 			 &sport->gid.global.interface_id);
-	sport->port_gid_id.wwn.priv = sport;
-	snprintf(sport->port_gid_id.name, sizeof(sport->port_gid_id.name),
+	snprintf(sport->gid_name, ARRAY_SIZE(sport->gid_name),
 		 "0x%016llx%016llx",
 		 be64_to_cpu(sport->gid.global.subnet_prefix),
 		 be64_to_cpu(sport->gid.global.interface_id));
@@ -596,24 +600,26 @@
 		set_bit(IB_MGMT_METHOD_GET, reg_req.method_mask);
 		set_bit(IB_MGMT_METHOD_SET, reg_req.method_mask);
 
-		sport->mad_agent = ib_register_mad_agent(sport->sdev->device,
-							 sport->port,
-							 IB_QPT_GSI,
-							 &reg_req, 0,
-							 srpt_mad_send_handler,
-							 srpt_mad_recv_handler,
-							 sport, 0);
-		if (IS_ERR(sport->mad_agent)) {
+		mad_agent = ib_register_mad_agent(sport->sdev->device,
+						  sport->port,
+						  IB_QPT_GSI,
+						  &reg_req, 0,
+						  srpt_mad_send_handler,
+						  srpt_mad_recv_handler,
+						  sport, 0);
+		if (IS_ERR(mad_agent)) {
 			pr_err("%s-%d: MAD agent registration failed (%ld). Note: this is expected if SR-IOV is enabled.\n",
 			       dev_name(&sport->sdev->device->dev), sport->port,
-			       PTR_ERR(sport->mad_agent));
+			       PTR_ERR(mad_agent));
 			sport->mad_agent = NULL;
 			memset(&port_modify, 0, sizeof(port_modify));
 			port_modify.clr_port_cap_mask = IB_PORT_DEVICE_MGMT_SUP;
 			ib_modify_port(sport->sdev->device, sport->port, 0,
 				       &port_modify);
-
+			return 0;
 		}
+
+		sport->mad_agent = mad_agent;
 	}
 
 	return 0;
@@ -1807,8 +1813,7 @@
 	ch->cq_size = ch->rq_size + sq_size;
 
 	qp_init->qp_context = (void *)ch;
-	qp_init->event_handler
-		= (void(*)(struct ib_event *, void*))srpt_qp_event;
+	qp_init->event_handler = srpt_qp_event;
 	qp_init->send_cq = ch->cq;
 	qp_init->recv_cq = ch->cq;
 	qp_init->sq_sig_type = IB_SIGNAL_REQ_WR;
@@ -2314,31 +2319,35 @@
 	tag_num = ch->rq_size;
 	tag_size = 1; /* ib_srpt does not use se_sess->sess_cmd_map */
 
-	mutex_lock(&sport->port_guid_id.mutex);
-	list_for_each_entry(stpg, &sport->port_guid_id.tpg_list, entry) {
-		if (!IS_ERR_OR_NULL(ch->sess))
-			break;
-		ch->sess = target_setup_session(&stpg->tpg, tag_num,
+	if (sport->guid_id) {
+		mutex_lock(&sport->guid_id->mutex);
+		list_for_each_entry(stpg, &sport->guid_id->tpg_list, entry) {
+			if (!IS_ERR_OR_NULL(ch->sess))
+				break;
+			ch->sess = target_setup_session(&stpg->tpg, tag_num,
 						tag_size, TARGET_PROT_NORMAL,
 						ch->sess_name, ch, NULL);
+		}
+		mutex_unlock(&sport->guid_id->mutex);
 	}
-	mutex_unlock(&sport->port_guid_id.mutex);
 
-	mutex_lock(&sport->port_gid_id.mutex);
-	list_for_each_entry(stpg, &sport->port_gid_id.tpg_list, entry) {
-		if (!IS_ERR_OR_NULL(ch->sess))
-			break;
-		ch->sess = target_setup_session(&stpg->tpg, tag_num,
+	if (sport->gid_id) {
+		mutex_lock(&sport->gid_id->mutex);
+		list_for_each_entry(stpg, &sport->gid_id->tpg_list, entry) {
+			if (!IS_ERR_OR_NULL(ch->sess))
+				break;
+			ch->sess = target_setup_session(&stpg->tpg, tag_num,
 					tag_size, TARGET_PROT_NORMAL, i_port_id,
 					ch, NULL);
-		if (!IS_ERR_OR_NULL(ch->sess))
-			break;
-		/* Retry without leading "0x" */
-		ch->sess = target_setup_session(&stpg->tpg, tag_num,
+			if (!IS_ERR_OR_NULL(ch->sess))
+				break;
+			/* Retry without leading "0x" */
+			ch->sess = target_setup_session(&stpg->tpg, tag_num,
 						tag_size, TARGET_PROT_NORMAL,
 						i_port_id + 2, ch, NULL);
+		}
+		mutex_unlock(&sport->gid_id->mutex);
 	}
-	mutex_unlock(&sport->port_gid_id.mutex);
 
 	if (IS_ERR_OR_NULL(ch->sess)) {
 		WARN_ON_ONCE(ch->sess == NULL);
@@ -2983,7 +2992,12 @@
 	return 0;
 }
 
-static struct se_wwn *__srpt_lookup_wwn(const char *name)
+struct port_and_port_id {
+	struct srpt_port *sport;
+	struct srpt_port_id **port_id;
+};
+
+static struct port_and_port_id __srpt_lookup_port(const char *name)
 {
 	struct ib_device *dev;
 	struct srpt_device *sdev;
@@ -2998,25 +3012,38 @@
 		for (i = 0; i < dev->phys_port_cnt; i++) {
 			sport = &sdev->port[i];
 
-			if (strcmp(sport->port_guid_id.name, name) == 0)
-				return &sport->port_guid_id.wwn;
-			if (strcmp(sport->port_gid_id.name, name) == 0)
-				return &sport->port_gid_id.wwn;
+			if (strcmp(sport->guid_name, name) == 0) {
+				kref_get(&sdev->refcnt);
+				return (struct port_and_port_id){
+					sport, &sport->guid_id};
+			}
+			if (strcmp(sport->gid_name, name) == 0) {
+				kref_get(&sdev->refcnt);
+				return (struct port_and_port_id){
+					sport, &sport->gid_id};
+			}
 		}
 	}
 
-	return NULL;
+	return (struct port_and_port_id){};
 }
 
-static struct se_wwn *srpt_lookup_wwn(const char *name)
+/**
+ * srpt_lookup_port() - Look up an RDMA port by name
+ * @name: ASCII port name
+ *
+ * Increments the RDMA port reference count if an RDMA port pointer is returned.
+ * The caller must drop that reference count by calling srpt_port_put_ref().
+ */
+static struct port_and_port_id srpt_lookup_port(const char *name)
 {
-	struct se_wwn *wwn;
+	struct port_and_port_id papi;
 
 	spin_lock(&srpt_dev_lock);
-	wwn = __srpt_lookup_wwn(name);
+	papi = __srpt_lookup_port(name);
 	spin_unlock(&srpt_dev_lock);
 
-	return wwn;
+	return papi;
 }
 
 static void srpt_free_srq(struct srpt_device *sdev)
@@ -3101,6 +3128,18 @@
 	return ret;
 }
 
+static void srpt_free_sdev(struct kref *refcnt)
+{
+	struct srpt_device *sdev = container_of(refcnt, typeof(*sdev), refcnt);
+
+	kfree(sdev);
+}
+
+static void srpt_sdev_put(struct srpt_device *sdev)
+{
+	kref_put(&sdev->refcnt, srpt_free_sdev);
+}
+
 /**
  * srpt_add_one - InfiniBand device addition callback function
  * @device: Describes a HCA.
@@ -3119,6 +3158,7 @@
 	if (!sdev)
 		return -ENOMEM;
 
+	kref_init(&sdev->refcnt);
 	sdev->device = device;
 	mutex_init(&sdev->sdev_mutex);
 
@@ -3169,7 +3209,6 @@
 
 	INIT_IB_EVENT_HANDLER(&sdev->event_handler, sdev->device,
 			      srpt_event_handler);
-	ib_register_event_handler(&sdev->event_handler);
 
 	for (i = 1; i <= sdev->device->phys_port_cnt; i++) {
 		sport = &sdev->port[i - 1];
@@ -3182,10 +3221,6 @@
 		sport->port_attrib.srp_sq_size = DEF_SRPT_SQ_SIZE;
 		sport->port_attrib.use_srq = false;
 		INIT_WORK(&sport->work, srpt_refresh_port_work);
-		mutex_init(&sport->port_guid_id.mutex);
-		INIT_LIST_HEAD(&sport->port_guid_id.tpg_list);
-		mutex_init(&sport->port_gid_id.mutex);
-		INIT_LIST_HEAD(&sport->port_gid_id.tpg_list);
 
 		ret = srpt_refresh_port(sport);
 		if (ret) {
@@ -3196,6 +3231,7 @@
 		}
 	}
 
+	ib_register_event_handler(&sdev->event_handler);
 	spin_lock(&srpt_dev_lock);
 	list_add_tail(&sdev->list, &srpt_dev_list);
 	spin_unlock(&srpt_dev_lock);
@@ -3206,7 +3242,6 @@
 
 err_port:
 	srpt_unregister_mad_agent(sdev, i);
-	ib_unregister_event_handler(&sdev->event_handler);
 err_cm:
 	if (sdev->cm_id)
 		ib_destroy_cm_id(sdev->cm_id);
@@ -3214,7 +3249,7 @@
 	srpt_free_srq(sdev);
 	ib_dealloc_pd(sdev->pd);
 free_dev:
-	kfree(sdev);
+	srpt_sdev_put(sdev);
 	pr_info("%s(%s) failed.\n", __func__, dev_name(&device->dev));
 	return ret;
 }
@@ -3258,7 +3293,7 @@
 
 	ib_dealloc_pd(sdev->pd);
 
-	kfree(sdev);
+	srpt_sdev_put(sdev);
 }
 
 static struct ib_client srpt_client = {
@@ -3286,10 +3321,10 @@
 {
 	struct srpt_port *sport = wwn->priv;
 
-	if (wwn == &sport->port_guid_id.wwn)
-		return &sport->port_guid_id;
-	if (wwn == &sport->port_gid_id.wwn)
-		return &sport->port_gid_id;
+	if (sport->guid_id && &sport->guid_id->wwn == wwn)
+		return sport->guid_id;
+	if (sport->gid_id && &sport->gid_id->wwn == wwn)
+		return sport->gid_id;
 	WARN_ON_ONCE(true);
 	return NULL;
 }
@@ -3804,7 +3839,31 @@
 				      struct config_group *group,
 				      const char *name)
 {
-	return srpt_lookup_wwn(name) ? : ERR_PTR(-EINVAL);
+	struct port_and_port_id papi = srpt_lookup_port(name);
+	struct srpt_port *sport = papi.sport;
+	struct srpt_port_id *port_id;
+
+	if (!papi.port_id)
+		return ERR_PTR(-EINVAL);
+	if (*papi.port_id) {
+		/* Attempt to create a directory that already exists. */
+		WARN_ON_ONCE(true);
+		return &(*papi.port_id)->wwn;
+	}
+	port_id = kzalloc(sizeof(*port_id), GFP_KERNEL);
+	if (!port_id) {
+		srpt_sdev_put(sport->sdev);
+		return ERR_PTR(-ENOMEM);
+	}
+	mutex_init(&port_id->mutex);
+	INIT_LIST_HEAD(&port_id->tpg_list);
+	port_id->wwn.priv = sport;
+	memcpy(port_id->name, port_id == sport->guid_id ? sport->guid_name :
+	       sport->gid_name, ARRAY_SIZE(port_id->name));
+
+	*papi.port_id = port_id;
+
+	return &port_id->wwn;
 }
 
 /**
@@ -3813,6 +3872,18 @@
  */
 static void srpt_drop_tport(struct se_wwn *wwn)
 {
+	struct srpt_port_id *port_id = container_of(wwn, typeof(*port_id), wwn);
+	struct srpt_port *sport = wwn->priv;
+
+	if (sport->guid_id == port_id)
+		sport->guid_id = NULL;
+	else if (sport->gid_id == port_id)
+		sport->gid_id = NULL;
+	else
+		WARN_ON_ONCE(true);
+
+	srpt_sdev_put(sport->sdev);
+	kfree(port_id);
 }
 
 static ssize_t srpt_wwn_version_show(struct config_item *item, char *buf)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/infiniband/ulp/srpt/ib_srpt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/infiniband/ulp/srpt/ib_srpt.h
@@ -376,7 +376,7 @@
 };
 
 /**
- * struct srpt_port_id - information about an RDMA port name
+ * struct srpt_port_id - LIO RDMA port information
  * @mutex:	Protects @tpg_list changes.
  * @tpg_list:	TPGs associated with the RDMA port name.
  * @wwn:	WWN associated with the RDMA port name.
@@ -393,7 +393,7 @@
 };
 
 /**
- * struct srpt_port - information associated by SRPT with a single IB port
+ * struct srpt_port - SRPT RDMA port information
  * @sdev:      backpointer to the HCA information.
  * @mad_agent: per-port management datagram processing information.
  * @enabled:   Whether or not this target port is enabled.
@@ -402,8 +402,10 @@
  * @lid:       cached value of the port's lid.
  * @gid:       cached value of the port's gid.
  * @work:      work structure for refreshing the aforementioned cached values.
- * @port_guid_id: target port GUID
- * @port_gid_id: target port GID
+ * @guid_name: port name in GUID format.
+ * @guid_id:   LIO target port information for the port name in GUID format.
+ * @gid_name:  port name in GID format.
+ * @gid_id:    LIO target port information for the port name in GID format.
  * @port_attrib:   Port attributes that can be accessed through configfs.
  * @refcount:	   Number of objects associated with this port.
  * @freed_channels: Completion that will be signaled once @refcount becomes 0.
@@ -419,8 +421,10 @@
 	u32			lid;
 	union ib_gid		gid;
 	struct work_struct	work;
-	struct srpt_port_id	port_guid_id;
-	struct srpt_port_id	port_gid_id;
+	char			guid_name[64];
+	struct srpt_port_id	*guid_id;
+	char			gid_name[64];
+	struct srpt_port_id	*gid_id;
 	struct srpt_port_attrib port_attrib;
 	atomic_t		refcount;
 	struct completion	*freed_channels;
@@ -430,6 +434,7 @@
 
 /**
  * struct srpt_device - information associated by SRPT with a single HCA
+ * @refcnt:	   Reference count for this device.
  * @device:        Backpointer to the struct ib_device managed by the IB core.
  * @pd:            IB protection domain.
  * @lkey:          L_Key (local key) with write access to all local memory.
@@ -445,6 +450,7 @@
  * @port:          Information about the ports owned by this HCA.
  */
 struct srpt_device {
+	struct kref		refcnt;
 	struct ib_device	*device;
 	struct ib_pd		*pd;
 	u32			lkey;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/ff-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/ff-core.c
@@ -12,8 +12,10 @@
 /* #define DEBUG */
 
 #include <linux/input.h>
+#include <linux/limits.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
+#include <linux/overflow.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
 
@@ -318,9 +320,8 @@
 		return -EINVAL;
 	}
 
-	ff_dev_size = sizeof(struct ff_device) +
-				max_effects * sizeof(struct file *);
-	if (ff_dev_size < max_effects) /* overflow */
+	ff_dev_size = struct_size(ff, effect_owners, max_effects);
+	if (ff_dev_size == SIZE_MAX) /* overflow */
 		return -EINVAL;
 
 	ff = kzalloc(ff_dev_size, GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/input-mt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/input-mt.c
@@ -45,6 +45,9 @@
 		return 0;
 	if (mt)
 		return mt->num_slots != num_slots ? -EINVAL : 0;
+	/* Arbitrary limit for avoiding too large memory allocation. */
+	if (num_slots > 1024)
+		return -EINVAL;
 
 	mt = kzalloc(struct_size(mt, slots, num_slots), GFP_KERNEL);
 	if (!mt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/input.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/input.c
@@ -47,6 +47,17 @@
 
 static const struct input_value input_value_sync = { EV_SYN, SYN_REPORT, 1 };
 
+static const unsigned int input_max_code[EV_CNT] = {
+	[EV_KEY] = KEY_MAX,
+	[EV_REL] = REL_MAX,
+	[EV_ABS] = ABS_MAX,
+	[EV_MSC] = MSC_MAX,
+	[EV_SW] = SW_MAX,
+	[EV_LED] = LED_MAX,
+	[EV_SND] = SND_MAX,
+	[EV_FF] = FF_MAX,
+};
+
 static inline int is_event_supported(unsigned int code,
 				     unsigned long *bm, unsigned int max)
 {
@@ -680,7 +691,7 @@
 
 	__input_release_device(handle);
 
-	if (!dev->inhibited && !--dev->users) {
+	if (!--dev->users && !dev->inhibited) {
 		if (dev->poller)
 			input_dev_poller_stop(dev->poller);
 		if (dev->close)
@@ -1349,19 +1360,19 @@
 				     char name, unsigned long *bm,
 				     unsigned int min_bit, unsigned int max_bit)
 {
-	int len = 0, i;
+	int bit = min_bit;
+	int len = 0;
 
 	len += snprintf(buf, max(size, 0), "%c", name);
-	for (i = min_bit; i < max_bit; i++)
-		if (bm[BIT_WORD(i)] & BIT_MASK(i))
-			len += snprintf(buf + len, max(size - len, 0), "%X,", i);
+	for_each_set_bit_from(bit, bm, max_bit)
+		len += snprintf(buf + len, max(size - len, 0), "%X,", bit);
 	return len;
 }
 
-static int input_print_modalias(char *buf, int size, struct input_dev *id,
-				int add_cr)
+static int input_print_modalias_parts(char *buf, int size, int full_len,
+				      struct input_dev *id)
 {
-	int len;
+	int len, klen, remainder, space;
 
 	len = snprintf(buf, max(size, 0),
 		       "input:b%04Xv%04Xp%04Xe%04X-",
@@ -1370,8 +1381,49 @@
 
 	len += input_print_modalias_bits(buf + len, size - len,
 				'e', id->evbit, 0, EV_MAX);
-	len += input_print_modalias_bits(buf + len, size - len,
+
+	/*
+	 * Calculate the remaining space in the buffer making sure we
+	 * have place for the terminating 0.
+	 */
+	space = max(size - (len + 1), 0);
+
+	klen = input_print_modalias_bits(buf + len, size - len,
 				'k', id->keybit, KEY_MIN_INTERESTING, KEY_MAX);
+	len += klen;
+
+	/*
+	 * If we have more data than we can fit in the buffer, check
+	 * if we can trim key data to fit in the rest. We will indicate
+	 * that key data is incomplete by adding "+" sign at the end, like
+	 * this: * "k1,2,3,45,+,".
+	 *
+	 * Note that we shortest key info (if present) is "k+," so we
+	 * can only try to trim if key data is longer than that.
+	 */
+	if (full_len && size < full_len + 1 && klen > 3) {
+		remainder = full_len - len;
+		/*
+		 * We can only trim if we have space for the remainder
+		 * and also for at least "k+," which is 3 more characters.
+		 */
+		if (remainder <= space - 3) {
+			int i;
+			/*
+			 * We are guaranteed to have 'k' in the buffer, so
+			 * we need at least 3 additional bytes for storing
+			 * "+," in addition to the remainder.
+			 */
+			for (i = size - 1 - remainder - 3; i >= 0; i--) {
+				if (buf[i] == 'k' || buf[i] == ',') {
+					strcpy(buf + i + 1, "+,");
+					len = i + 3; /* Not counting '\0' */
+					break;
+				}
+			}
+		}
+	}
+
 	len += input_print_modalias_bits(buf + len, size - len,
 				'r', id->relbit, 0, REL_MAX);
 	len += input_print_modalias_bits(buf + len, size - len,
@@ -1387,12 +1439,25 @@
 	len += input_print_modalias_bits(buf + len, size - len,
 				'w', id->swbit, 0, SW_MAX);
 
-	if (add_cr)
-		len += snprintf(buf + len, max(size - len, 0), "\n");
-
 	return len;
 }
 
+static int input_print_modalias(char *buf, int size, struct input_dev *id)
+{
+	int full_len;
+
+	/*
+	 * Printing is done in 2 passes: first one figures out total length
+	 * needed for the modalias string, second one will try to trim key
+	 * data in case when buffer is too small for the entire modalias.
+	 * If the buffer is too small regardless, it will fill as much as it
+	 * can (without trimming key data) into the buffer and leave it to
+	 * the caller to figure out what to do with the result.
+	 */
+	full_len = input_print_modalias_parts(NULL, 0, 0, id);
+	return input_print_modalias_parts(buf, size, full_len, id);
+}
+
 static ssize_t input_dev_show_modalias(struct device *dev,
 				       struct device_attribute *attr,
 				       char *buf)
@@ -1400,7 +1465,9 @@
 	struct input_dev *id = to_input_dev(dev);
 	ssize_t len;
 
-	len = input_print_modalias(buf, PAGE_SIZE, id, 1);
+	len = input_print_modalias(buf, PAGE_SIZE, id);
+	if (len < PAGE_SIZE - 2)
+		len += snprintf(buf + len, PAGE_SIZE - len, "\n");
 
 	return min_t(int, len, PAGE_SIZE);
 }
@@ -1612,6 +1679,23 @@
 	return 0;
 }
 
+/*
+ * This is a pretty gross hack. When building uevent data the driver core
+ * may try adding more environment variables to kobj_uevent_env without
+ * telling us, so we have no idea how much of the buffer we can use to
+ * avoid overflows/-ENOMEM elsewhere. To work around this let's artificially
+ * reduce amount of memory we will use for the modalias environment variable.
+ *
+ * The potential additions are:
+ *
+ * SEQNUM=18446744073709551615 - (%llu - 28 bytes)
+ * HOME=/ (6 bytes)
+ * PATH=/sbin:/bin:/usr/sbin:/usr/bin (34 bytes)
+ *
+ * 68 bytes total. Allow extra buffer - 96 bytes
+ */
+#define UEVENT_ENV_EXTRA_LEN	96
+
 static int input_add_uevent_modalias_var(struct kobj_uevent_env *env,
 					 struct input_dev *dev)
 {
@@ -1621,9 +1705,11 @@
 		return -ENOMEM;
 
 	len = input_print_modalias(&env->buf[env->buflen - 1],
-				   sizeof(env->buf) - env->buflen,
-				   dev, 0);
-	if (len >= (sizeof(env->buf) - env->buflen))
+				   (int)sizeof(env->buf) - env->buflen -
+					UEVENT_ENV_EXTRA_LEN,
+				   dev);
+	if (len >= ((int)sizeof(env->buf) - env->buflen -
+					UEVENT_ENV_EXTRA_LEN))
 		return -ENOMEM;
 
 	env->buflen += len;
@@ -2074,6 +2160,14 @@
  */
 void input_set_capability(struct input_dev *dev, unsigned int type, unsigned int code)
 {
+	if (type < EV_CNT && input_max_code[type] &&
+	    code > input_max_code[type]) {
+		pr_err("%s: invalid code %u for type %u\n", __func__, code,
+		       type);
+		dump_stack();
+		return;
+	}
+
 	switch (type) {
 	case EV_KEY:
 		__set_bit(code, dev->keybit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/Kconfig
@@ -46,6 +46,7 @@
 config JOYSTICK_ADC
 	tristate "Simple joystick connected over ADC"
 	depends on IIO
+	select IIO_BUFFER
 	select IIO_BUFFER_CB
 	help
 	  Say Y here if you have a simple joystick connected over ADC.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/iforce/iforce-main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/iforce/iforce-main.c
@@ -50,6 +50,7 @@
 	{ 0x046d, 0xc291, "Logitech WingMan Formula Force",		btn_wheel, abs_wheel, ff_iforce },
 	{ 0x05ef, 0x020a, "AVB Top Shot Pegasus",			btn_joystick_avb, abs_avb_pegasus, ff_iforce },
 	{ 0x05ef, 0x8884, "AVB Mag Turbo Force",			btn_wheel, abs_wheel, ff_iforce },
+	{ 0x05ef, 0x8886, "Boeder Force Feedback Wheel",		btn_wheel, abs_wheel, ff_iforce },
 	{ 0x05ef, 0x8888, "AVB Top Shot Force Feedback Racing Wheel",	btn_wheel, abs_wheel, ff_iforce }, //?
 	{ 0x061c, 0xc0a4, "ACT LABS Force RS",                          btn_wheel, abs_wheel, ff_iforce }, //?
 	{ 0x061c, 0xc084, "ACT LABS Force RS",				btn_wheel, abs_wheel, ff_iforce },
@@ -272,22 +273,22 @@
  * Get device info.
  */
 
-	if (!iforce_get_id_packet(iforce, 'M', buf, &len) || len < 3)
+	if (!iforce_get_id_packet(iforce, 'M', buf, &len) && len >= 3)
 		input_dev->id.vendor = get_unaligned_le16(buf + 1);
 	else
 		dev_warn(&iforce->dev->dev, "Device does not respond to id packet M\n");
 
-	if (!iforce_get_id_packet(iforce, 'P', buf, &len) || len < 3)
+	if (!iforce_get_id_packet(iforce, 'P', buf, &len) && len >= 3)
 		input_dev->id.product = get_unaligned_le16(buf + 1);
 	else
 		dev_warn(&iforce->dev->dev, "Device does not respond to id packet P\n");
 
-	if (!iforce_get_id_packet(iforce, 'B', buf, &len) || len < 3)
+	if (!iforce_get_id_packet(iforce, 'B', buf, &len) && len >= 3)
 		iforce->device_memory.end = get_unaligned_le16(buf + 1);
 	else
 		dev_warn(&iforce->dev->dev, "Device does not respond to id packet B\n");
 
-	if (!iforce_get_id_packet(iforce, 'N', buf, &len) || len < 2)
+	if (!iforce_get_id_packet(iforce, 'N', buf, &len) && len >= 2)
 		ff_effects = buf[1];
 	else
 		dev_warn(&iforce->dev->dev, "Device does not respond to id packet N\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/iforce/iforce-serio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/iforce/iforce-serio.c
@@ -39,7 +39,7 @@
 
 again:
 	if (iforce->xmit.head == iforce->xmit.tail) {
-		clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
+		iforce_clear_xmit_and_wake(iforce);
 		spin_unlock_irqrestore(&iforce->xmit_lock, flags);
 		return;
 	}
@@ -64,7 +64,7 @@
 	if (test_and_clear_bit(IFORCE_XMIT_AGAIN, iforce->xmit_flags))
 		goto again;
 
-	clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
+	iforce_clear_xmit_and_wake(iforce);
 
 	spin_unlock_irqrestore(&iforce->xmit_lock, flags);
 }
@@ -169,7 +169,7 @@
 			iforce_serio->cmd_response_len = iforce_serio->len;
 
 			/* Signal that command is done */
-			wake_up(&iforce->wait);
+			wake_up_all(&iforce->wait);
 		} else if (likely(iforce->type)) {
 			iforce_process_packet(iforce, iforce_serio->id,
 					      iforce_serio->data_in,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/iforce/iforce-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/iforce/iforce-usb.c
@@ -30,7 +30,7 @@
 	spin_lock_irqsave(&iforce->xmit_lock, flags);
 
 	if (iforce->xmit.head == iforce->xmit.tail) {
-		clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
+		iforce_clear_xmit_and_wake(iforce);
 		spin_unlock_irqrestore(&iforce->xmit_lock, flags);
 		return;
 	}
@@ -58,9 +58,9 @@
 	XMIT_INC(iforce->xmit.tail, n);
 
 	if ( (n=usb_submit_urb(iforce_usb->out, GFP_ATOMIC)) ) {
-		clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
 		dev_warn(&iforce_usb->intf->dev,
 			 "usb_submit_urb failed %d\n", n);
+		iforce_clear_xmit_and_wake(iforce);
 	}
 
 	/* The IFORCE_XMIT_RUNNING bit is not cleared here. That's intended.
@@ -92,7 +92,7 @@
 				 id,
 				 USB_TYPE_VENDOR | USB_DIR_IN |
 					USB_RECIP_INTERFACE,
-				 0, 0, buf, IFORCE_MAX_LENGTH, HZ);
+				 0, 0, buf, IFORCE_MAX_LENGTH, 1000);
 	if (status < 0) {
 		dev_err(&iforce_usb->intf->dev,
 			"usb_submit_urb failed: %d\n", status);
@@ -175,15 +175,15 @@
 	struct iforce *iforce = &iforce_usb->iforce;
 
 	if (urb->status) {
-		clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
 		dev_dbg(&iforce_usb->intf->dev, "urb->status %d, exiting\n",
 			urb->status);
+		iforce_clear_xmit_and_wake(iforce);
 		return;
 	}
 
 	__iforce_usb_xmit(iforce);
 
-	wake_up(&iforce->wait);
+	wake_up_all(&iforce->wait);
 }
 
 static int iforce_usb_probe(struct usb_interface *intf,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/iforce/iforce.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/iforce/iforce.h
@@ -119,6 +119,12 @@
 					 response_data, response_len);
 }
 
+static inline void iforce_clear_xmit_and_wake(struct iforce *iforce)
+{
+	clear_bit(IFORCE_XMIT_RUNNING, iforce->xmit_flags);
+	wake_up_all(&iforce->wait);
+}
+
 /* Public functions */
 /* iforce-main.c */
 int iforce_init_device(struct device *parent, u16 bustype,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/spaceball.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/spaceball.c
@@ -19,6 +19,7 @@
 #include <linux/module.h>
 #include <linux/input.h>
 #include <linux/serio.h>
+#include <asm/unaligned.h>
 
 #define DRIVER_DESC	"SpaceTec SpaceBall 2003/3003/4000 FLX driver"
 
@@ -75,9 +76,15 @@
 
 		case 'D':					/* Ball data */
 			if (spaceball->idx != 15) return;
-			for (i = 0; i < 6; i++)
+			/*
+			 * Skip first three bytes; read six axes worth of data.
+			 * Axis values are signed 16-bit big-endian.
+			 */
+			data += 3;
+			for (i = 0; i < ARRAY_SIZE(spaceball_axes); i++) {
 				input_report_abs(dev, spaceball_axes[i],
-					(__s16)((data[2 * i + 3] << 8) | data[2 * i + 2]));
+					(__s16)get_unaligned_be16(&data[i * 2]));
+			}
 			break;
 
 		case 'K':					/* Button data */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/joystick/xpad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/joystick/xpad.c
@@ -113,11 +113,14 @@
 	u8 xtype;
 } xpad_device[] = {
 	{ 0x0079, 0x18d4, "GPD Win 2 X-Box Controller", 0, XTYPE_XBOX360 },
+	{ 0x03eb, 0xff01, "Wooting One (Legacy)", 0, XTYPE_XBOX360 },
+	{ 0x03eb, 0xff02, "Wooting Two (Legacy)", 0, XTYPE_XBOX360 },
 	{ 0x044f, 0x0f00, "Thrustmaster Wheel", 0, XTYPE_XBOX },
 	{ 0x044f, 0x0f03, "Thrustmaster Wheel", 0, XTYPE_XBOX },
 	{ 0x044f, 0x0f07, "Thrustmaster, Inc. Controller", 0, XTYPE_XBOX },
 	{ 0x044f, 0x0f10, "Thrustmaster Modena GT Wheel", 0, XTYPE_XBOX },
 	{ 0x044f, 0xb326, "Thrustmaster Gamepad GP XID", 0, XTYPE_XBOX360 },
+	{ 0x03f0, 0x0495, "HyperX Clutch Gladiate", 0, XTYPE_XBOXONE },
 	{ 0x045e, 0x0202, "Microsoft X-Box pad v1 (US)", 0, XTYPE_XBOX },
 	{ 0x045e, 0x0285, "Microsoft X-Box pad (Japan)", 0, XTYPE_XBOX },
 	{ 0x045e, 0x0287, "Microsoft Xbox Controller S", 0, XTYPE_XBOX },
@@ -126,6 +129,7 @@
 	{ 0x045e, 0x028e, "Microsoft X-Box 360 pad", 0, XTYPE_XBOX360 },
 	{ 0x045e, 0x028f, "Microsoft X-Box 360 pad v2", 0, XTYPE_XBOX360 },
 	{ 0x045e, 0x0291, "Xbox 360 Wireless Receiver (XBOX)", MAP_DPAD_TO_BUTTONS, XTYPE_XBOX360W },
+	{ 0x045e, 0x02a9, "Xbox 360 Wireless Receiver (Unofficial)", MAP_DPAD_TO_BUTTONS, XTYPE_XBOX360W },
 	{ 0x045e, 0x02d1, "Microsoft X-Box One pad", 0, XTYPE_XBOXONE },
 	{ 0x045e, 0x02dd, "Microsoft X-Box One pad (Firmware 2015)", 0, XTYPE_XBOXONE },
 	{ 0x045e, 0x02e3, "Microsoft X-Box One Elite pad", 0, XTYPE_XBOXONE },
@@ -244,6 +248,7 @@
 	{ 0x0f0d, 0x0063, "Hori Real Arcade Pro Hayabusa (USA) Xbox One", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOXONE },
 	{ 0x0f0d, 0x0067, "HORIPAD ONE", 0, XTYPE_XBOXONE },
 	{ 0x0f0d, 0x0078, "Hori Real Arcade Pro V Kai Xbox One", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOXONE },
+	{ 0x0f0d, 0x00c5, "Hori Fighting Commander ONE", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOXONE },
 	{ 0x0f30, 0x010b, "Philips Recoil", 0, XTYPE_XBOX },
 	{ 0x0f30, 0x0202, "Joytech Advanced Controller", 0, XTYPE_XBOX },
 	{ 0x0f30, 0x8888, "BigBen XBMiniPad Controller", 0, XTYPE_XBOX },
@@ -251,6 +256,7 @@
 	{ 0x1038, 0x1430, "SteelSeries Stratus Duo", 0, XTYPE_XBOX360 },
 	{ 0x1038, 0x1431, "SteelSeries Stratus Duo", 0, XTYPE_XBOX360 },
 	{ 0x11c9, 0x55f0, "Nacon GC-100XF", 0, XTYPE_XBOX360 },
+	{ 0x11ff, 0x0511, "PXN V900", 0, XTYPE_XBOX360 },
 	{ 0x1209, 0x2882, "Ardwiino Controller", 0, XTYPE_XBOX360 },
 	{ 0x12ab, 0x0004, "Honey Bee Xbox360 dancepad", MAP_DPAD_TO_BUTTONS, XTYPE_XBOX360 },
 	{ 0x12ab, 0x0301, "PDP AFTERGLOW AX.1", 0, XTYPE_XBOX360 },
@@ -260,9 +266,10 @@
 	{ 0x1430, 0x8888, "TX6500+ Dance Pad (first generation)", MAP_DPAD_TO_BUTTONS, XTYPE_XBOX },
 	{ 0x1430, 0xf801, "RedOctane Controller", 0, XTYPE_XBOX360 },
 	{ 0x146b, 0x0601, "BigBen Interactive XBOX 360 Controller", 0, XTYPE_XBOX360 },
-	{ 0x1532, 0x0037, "Razer Sabertooth", 0, XTYPE_XBOX360 },
+	{ 0x146b, 0x0604, "Bigben Interactive DAIJA Arcade Stick", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOX360 },
 	{ 0x1532, 0x0a00, "Razer Atrox Arcade Stick", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOXONE },
 	{ 0x1532, 0x0a03, "Razer Wildcat", 0, XTYPE_XBOXONE },
+	{ 0x1532, 0x0a29, "Razer Wolverine V2", 0, XTYPE_XBOXONE },
 	{ 0x15e4, 0x3f00, "Power A Mini Pro Elite", 0, XTYPE_XBOX360 },
 	{ 0x15e4, 0x3f0a, "Xbox Airflo wired controller", 0, XTYPE_XBOX360 },
 	{ 0x15e4, 0x3f10, "Batarang Xbox 360 controller", 0, XTYPE_XBOX360 },
@@ -270,6 +277,7 @@
 	{ 0x1689, 0xfd00, "Razer Onza Tournament Edition", 0, XTYPE_XBOX360 },
 	{ 0x1689, 0xfd01, "Razer Onza Classic Edition", 0, XTYPE_XBOX360 },
 	{ 0x1689, 0xfe00, "Razer Sabertooth", 0, XTYPE_XBOX360 },
+	{ 0x17ef, 0x6182, "Lenovo Legion Controller for Windows", 0, XTYPE_XBOX360 },
 	{ 0x1949, 0x041a, "Amazon Game Controller", 0, XTYPE_XBOX360 },
 	{ 0x1bad, 0x0002, "Harmonix Rock Band Guitar", 0, XTYPE_XBOX360 },
 	{ 0x1bad, 0x0003, "Harmonix Rock Band Drumkit", MAP_DPAD_TO_BUTTONS, XTYPE_XBOX360 },
@@ -325,6 +333,7 @@
 	{ 0x24c6, 0x5502, "Hori Fighting Stick VX Alt", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOX360 },
 	{ 0x24c6, 0x5503, "Hori Fighting Edge", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOX360 },
 	{ 0x24c6, 0x5506, "Hori SOULCALIBUR V Stick", 0, XTYPE_XBOX360 },
+	{ 0x24c6, 0x5510, "Hori Fighting Commander ONE (Xbox 360/PC Mode)", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOX360 },
 	{ 0x24c6, 0x550d, "Hori GEM Xbox controller", 0, XTYPE_XBOX360 },
 	{ 0x24c6, 0x550e, "Hori Real Arcade Pro V Kai 360", MAP_TRIGGERS_TO_BUTTONS, XTYPE_XBOX360 },
 	{ 0x24c6, 0x551a, "PowerA FUSION Pro Controller", 0, XTYPE_XBOXONE },
@@ -334,6 +343,15 @@
 	{ 0x24c6, 0x5b03, "Thrustmaster Ferrari 458 Racing Wheel", 0, XTYPE_XBOX360 },
 	{ 0x24c6, 0x5d04, "Razer Sabertooth", 0, XTYPE_XBOX360 },
 	{ 0x24c6, 0xfafe, "Rock Candy Gamepad for Xbox 360", 0, XTYPE_XBOX360 },
+	{ 0x2563, 0x058d, "OneXPlayer Gamepad", 0, XTYPE_XBOX360 },
+	{ 0x2dc8, 0x2000, "8BitDo Pro 2 Wired Controller fox Xbox", 0, XTYPE_XBOXONE },
+	{ 0x31e3, 0x1100, "Wooting One", 0, XTYPE_XBOX360 },
+	{ 0x31e3, 0x1200, "Wooting Two", 0, XTYPE_XBOX360 },
+	{ 0x31e3, 0x1210, "Wooting Lekker", 0, XTYPE_XBOX360 },
+	{ 0x31e3, 0x1220, "Wooting Two HE", 0, XTYPE_XBOX360 },
+	{ 0x31e3, 0x1230, "Wooting Two HE (ARM)", 0, XTYPE_XBOX360 },
+	{ 0x31e3, 0x1300, "Wooting 60HE (AVR)", 0, XTYPE_XBOX360 },
+	{ 0x31e3, 0x1310, "Wooting 60HE (ARM)", 0, XTYPE_XBOX360 },
 	{ 0x3285, 0x0607, "Nacon GC-100", 0, XTYPE_XBOX360 },
 	{ 0x3767, 0x0101, "Fanatec Speedster 3 Forceshock Wheel", 0, XTYPE_XBOX },
 	{ 0xffff, 0xffff, "Chinese-made Xbox Controller", 0, XTYPE_XBOX },
@@ -419,7 +437,9 @@
 static const struct usb_device_id xpad_table[] = {
 	{ USB_INTERFACE_INFO('X', 'B', 0) },	/* X-Box USB-IF not approved class */
 	XPAD_XBOX360_VENDOR(0x0079),		/* GPD Win 2 Controller */
+	XPAD_XBOX360_VENDOR(0x03eb),		/* Wooting Keyboards (Legacy) */
 	XPAD_XBOX360_VENDOR(0x044f),		/* Thrustmaster X-Box 360 controllers */
+	XPAD_XBOXONE_VENDOR(0x03f0),		/* HP HyperX Xbox One Controllers */
 	XPAD_XBOX360_VENDOR(0x045e),		/* Microsoft X-Box 360 controllers */
 	XPAD_XBOXONE_VENDOR(0x045e),		/* Microsoft X-Box One controllers */
 	XPAD_XBOX360_VENDOR(0x046d),		/* Logitech X-Box 360 style controllers */
@@ -429,12 +449,15 @@
 	{ USB_DEVICE(0x0738, 0x4540) },		/* Mad Catz Beat Pad */
 	XPAD_XBOXONE_VENDOR(0x0738),		/* Mad Catz FightStick TE 2 */
 	XPAD_XBOX360_VENDOR(0x07ff),		/* Mad Catz GamePad */
+	XPAD_XBOX360_VENDOR(0x0c12),		/* Zeroplus X-Box 360 controllers */
 	XPAD_XBOX360_VENDOR(0x0e6f),		/* 0x0e6f X-Box 360 controllers */
 	XPAD_XBOXONE_VENDOR(0x0e6f),		/* 0x0e6f X-Box One controllers */
 	XPAD_XBOX360_VENDOR(0x0f0d),		/* Hori Controllers */
 	XPAD_XBOXONE_VENDOR(0x0f0d),		/* Hori Controllers */
 	XPAD_XBOX360_VENDOR(0x1038),		/* SteelSeries Controllers */
+	XPAD_XBOXONE_VENDOR(0x10f5),		/* Turtle Beach Controllers */
 	XPAD_XBOX360_VENDOR(0x11c9),		/* Nacon GC100XF */
+	XPAD_XBOX360_VENDOR(0x11ff),		/* PXN V900 */
 	XPAD_XBOX360_VENDOR(0x1209),		/* Ardwiino Controllers */
 	XPAD_XBOX360_VENDOR(0x12ab),		/* X-Box 360 dance pads */
 	XPAD_XBOX360_VENDOR(0x1430),		/* RedOctane X-Box 360 controllers */
@@ -444,14 +467,19 @@
 	XPAD_XBOX360_VENDOR(0x15e4),		/* Numark X-Box 360 controllers */
 	XPAD_XBOX360_VENDOR(0x162e),		/* Joytech X-Box 360 controllers */
 	XPAD_XBOX360_VENDOR(0x1689),		/* Razer Onza */
+	XPAD_XBOX360_VENDOR(0x17ef),		/* Lenovo */
 	XPAD_XBOX360_VENDOR(0x1949),		/* Amazon controllers */
 	XPAD_XBOX360_VENDOR(0x1bad),		/* Harminix Rock Band Guitar and Drums */
 	XPAD_XBOX360_VENDOR(0x20d6),		/* PowerA Controllers */
 	XPAD_XBOXONE_VENDOR(0x20d6),		/* PowerA Controllers */
 	XPAD_XBOX360_VENDOR(0x24c6),		/* PowerA Controllers */
 	XPAD_XBOXONE_VENDOR(0x24c6),		/* PowerA Controllers */
+	XPAD_XBOX360_VENDOR(0x2563),		/* OneXPlayer Gamepad */
+	XPAD_XBOX360_VENDOR(0x260d),		/* Dareu H101 */
+	XPAD_XBOXONE_VENDOR(0x2dc8),		/* 8BitDo Pro 2 Wired Controller for Xbox */
 	XPAD_XBOXONE_VENDOR(0x2e24),		/* Hyperkin Duke X-Box One pad */
 	XPAD_XBOX360_VENDOR(0x2f24),		/* GameSir Controllers */
+	XPAD_XBOX360_VENDOR(0x31e3),		/* Wooting Keyboards */
 	XPAD_XBOX360_VENDOR(0x3285),		/* Nacon GC-100 */
 	{ }
 };
@@ -474,6 +502,9 @@
 	}
 
 
+#define GIP_WIRED_INTF_DATA 0
+#define GIP_WIRED_INTF_AUDIO 1
+
 /*
  * This packet is required for all Xbox One pads with 2015
  * or later firmware installed (or present from the factory).
@@ -1802,7 +1833,7 @@
 	}
 
 	if (xpad->xtype == XTYPE_XBOXONE &&
-	    intf->cur_altsetting->desc.bInterfaceNumber != 0) {
+	    intf->cur_altsetting->desc.bInterfaceNumber != GIP_WIRED_INTF_DATA) {
 		/*
 		 * The Xbox One controller lists three interfaces all with the
 		 * same interface class, subclass and protocol. Differentiate by
@@ -1972,7 +2003,6 @@
 	.disconnect	= xpad_disconnect,
 	.suspend	= xpad_suspend,
 	.resume		= xpad_resume,
-	.reset_resume	= xpad_resume,
 	.id_table	= xpad_table,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/Kconfig
@@ -556,7 +556,7 @@
 
 config KEYBOARD_SAMSUNG
 	tristate "Samsung keypad support"
-	depends on HAVE_CLK
+	depends on HAS_IOMEM && HAVE_CLK
 	select INPUT_MATRIXKMAP
 	help
 	  Say Y here if you want to use the keypad on your Samsung mobile
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/adp5589-keys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/adp5589-keys.c
@@ -391,10 +391,17 @@
 	struct adp5589_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = kpad->var->bank(kpad->gpiomap[off]);
 	unsigned int bit = kpad->var->bit(kpad->gpiomap[off]);
+	int val;
 
-	return !!(adp5589_read(kpad->client,
-			       kpad->var->reg(ADP5589_GPI_STATUS_A) + bank) &
-			       bit);
+	mutex_lock(&kpad->gpio_lock);
+	if (kpad->dir[bank] & bit)
+		val = kpad->dat_out[bank];
+	else
+		val = adp5589_read(kpad->client,
+				   kpad->var->reg(ADP5589_GPI_STATUS_A) + bank);
+	mutex_unlock(&kpad->gpio_lock);
+
+	return !!(val & bit);
 }
 
 static void adp5589_gpio_set_value(struct gpio_chip *chip,
@@ -936,10 +943,9 @@
 
 static void adp5589_clear_config(void *data)
 {
-	struct i2c_client *client = data;
-	struct adp5589_kpad *kpad = i2c_get_clientdata(client);
+	struct adp5589_kpad *kpad = data;
 
-	adp5589_write(client, kpad->var->reg(ADP5589_GENERAL_CFG), 0);
+	adp5589_write(kpad->client, kpad->var->reg(ADP5589_GENERAL_CFG), 0);
 }
 
 static int adp5589_probe(struct i2c_client *client,
@@ -983,7 +989,7 @@
 	}
 
 	error = devm_add_action_or_reset(&client->dev, adp5589_clear_config,
-					 client);
+					 kpad);
 	if (error)
 		return error;
 
@@ -1010,8 +1016,6 @@
 	if (error)
 		return error;
 
-	i2c_set_clientdata(client, kpad);
-
 	dev_info(&client->dev, "Rev.%d keypad, irq %d\n", revid, client->irq);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/atkbd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/atkbd.c
@@ -90,7 +90,7 @@
 	  0, 46, 45, 32, 18,  5,  4, 95,  0, 57, 47, 33, 20, 19,  6,183,
 	  0, 49, 48, 35, 34, 21,  7,184,  0,  0, 50, 36, 22,  8,  9,185,
 	  0, 51, 37, 23, 24, 11, 10,  0,  0, 52, 53, 38, 39, 25, 12,  0,
-	  0, 89, 40,  0, 26, 13,  0,  0, 58, 54, 28, 27,  0, 43,  0, 85,
+	  0, 89, 40,  0, 26, 13,  0,193, 58, 54, 28, 27,  0, 43,  0, 85,
 	  0, 86, 91, 90, 92,  0, 14, 94,  0, 79,124, 75, 71,121,  0,  0,
 	 82, 83, 80, 76, 77, 72,  1, 69, 87, 78, 81, 74, 55, 73, 70, 99,
 
@@ -756,6 +756,44 @@
 			ps2dev->serio->phys);
 }
 
+#ifdef CONFIG_X86
+static bool atkbd_is_portable_device(void)
+{
+	static const char * const chassis_types[] = {
+		"8",	/* Portable */
+		"9",	/* Laptop */
+		"10",	/* Notebook */
+		"14",	/* Sub-Notebook */
+		"31",	/* Convertible */
+		"32",	/* Detachable */
+	};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(chassis_types); i++)
+		if (dmi_match(DMI_CHASSIS_TYPE, chassis_types[i]))
+			return true;
+
+	return false;
+}
+
+/*
+ * On many modern laptops ATKBD_CMD_GETID may cause problems, on these laptops
+ * the controller is always in translated mode. In this mode mice/touchpads will
+ * not work. So in this case simply assume a keyboard is connected to avoid
+ * confusing some laptop keyboards.
+ *
+ * Skipping ATKBD_CMD_GETID ends up using a fake keyboard id. Using the standard
+ * 0xab83 id is ok in translated mode, only atkbd_select_set() checks atkbd->id
+ * and in translated mode that is a no-op.
+ */
+static bool atkbd_skip_getid(struct atkbd *atkbd)
+{
+	return atkbd->translated && atkbd_is_portable_device();
+}
+#else
+static inline bool atkbd_skip_getid(struct atkbd *atkbd) { return false; }
+#endif
+
 /*
  * atkbd_probe() probes for an AT keyboard on a serio port.
  */
@@ -777,6 +815,11 @@
 				 "keyboard reset failed on %s\n",
 				 ps2dev->serio->phys);
 
+	if (atkbd_skip_getid(atkbd)) {
+		atkbd->id = 0xab83;
+		return 0;
+	}
+
 /*
  * Then we check the keyboard ID. We should get 0xab83 under normal conditions.
  * Some keyboards report different values, but the first byte is always 0xab or
@@ -788,9 +831,9 @@
 	if (ps2_command(ps2dev, param, ATKBD_CMD_GETID)) {
 
 /*
- * If the get ID command failed, we check if we can at least set the LEDs on
- * the keyboard. This should work on every keyboard out there. It also turns
- * the LEDs off, which we want anyway.
+ * If the get ID command failed, we check if we can at least set
+ * the LEDs on the keyboard. This should work on every keyboard out there.
+ * It also turns the LEDs off, which we want anyway.
  */
 		param[0] = 0;
 		if (ps2_command(ps2dev, param, ATKBD_CMD_SETLEDS))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/gpio_keys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/gpio_keys.c
@@ -131,7 +131,7 @@
 
 	if (!bdata->gpiod)
 		hrtimer_cancel(&bdata->release_timer);
-	if (bdata->debounce_use_hrtimer)
+	else if (bdata->debounce_use_hrtimer)
 		hrtimer_cancel(&bdata->debounce_timer);
 	else
 		cancel_delayed_work_sync(&bdata->work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/gpio_keys_polled.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/gpio_keys_polled.c
@@ -319,12 +319,10 @@
 
 			error = devm_gpio_request_one(dev, button->gpio,
 					flags, button->desc ? : DRV_NAME);
-			if (error) {
-				dev_err(dev,
-					"unable to claim gpio %u, err=%d\n",
-					button->gpio, error);
-				return error;
-			}
+			if (error)
+				return dev_err_probe(dev, error,
+						     "unable to claim gpio %u\n",
+						     button->gpio);
 
 			bdata->gpiod = gpio_to_desc(button->gpio);
 			if (!bdata->gpiod) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/ipaq-micro-keys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/ipaq-micro-keys.c
@@ -105,6 +105,9 @@
 	keys->codes = devm_kmemdup(&pdev->dev, micro_keycodes,
 			   keys->input->keycodesize * keys->input->keycodemax,
 			   GFP_KERNEL);
+	if (!keys->codes)
+		return -ENOMEM;
+
 	keys->input->keycode = keys->codes;
 
 	__set_bit(EV_KEY, keys->input->evbit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/omap4-keypad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/omap4-keypad.c
@@ -393,7 +393,7 @@
 	 * revision register.
 	 */
 	error = pm_runtime_get_sync(dev);
-	if (error) {
+	if (error < 0) {
 		dev_err(dev, "pm_runtime_get_sync() failed\n");
 		pm_runtime_put_noidle(dev);
 		return error;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/qt1050.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/qt1050.c
@@ -226,7 +226,12 @@
 	int err;
 
 	/* Read Chip ID */
-	regmap_read(ts->regmap, QT1050_CHIP_ID, &val);
+	err = regmap_read(ts->regmap, QT1050_CHIP_ID, &val);
+	if (err) {
+		dev_err(&ts->client->dev, "Failed to read chip ID: %d\n", err);
+		return false;
+	}
+
 	if (val != QT1050_CHIP_ID_VER) {
 		dev_err(&ts->client->dev, "ID %d not supported\n", val);
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/snvs_pwrkey.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/snvs_pwrkey.c
@@ -20,7 +20,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
 
-#define SNVS_HPVIDR1_REG	0xF8
+#define SNVS_HPVIDR1_REG	0xBF8
 #define SNVS_LPSR_REG		0x4C	/* LP Status Register */
 #define SNVS_LPCR_REG		0x38	/* LP Control Register */
 #define SNVS_HPSR_REG		0x14
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/keyboard/tca6416-keypad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/keyboard/tca6416-keypad.c
@@ -148,7 +148,7 @@
 	if (chip->use_polling)
 		schedule_delayed_work(&chip->dwork, msecs_to_jiffies(100));
 	else
-		enable_irq(chip->irqnum);
+		enable_irq(chip->client->irq);
 
 	return 0;
 }
@@ -160,7 +160,7 @@
 	if (chip->use_polling)
 		cancel_delayed_work_sync(&chip->dwork);
 	else
-		disable_irq(chip->irqnum);
+		disable_irq(chip->client->irq);
 }
 
 static int tca6416_setup_registers(struct tca6416_keypad_chip *chip)
@@ -266,12 +266,7 @@
 		goto fail1;
 
 	if (!chip->use_polling) {
-		if (pdata->irq_is_gpio)
-			chip->irqnum = gpio_to_irq(client->irq);
-		else
-			chip->irqnum = client->irq;
-
-		error = request_threaded_irq(chip->irqnum, NULL,
+		error = request_threaded_irq(client->irq, NULL,
 					     tca6416_keys_isr,
 					     IRQF_TRIGGER_FALLING |
 					     IRQF_ONESHOT | IRQF_NO_AUTOEN,
@@ -279,7 +274,7 @@
 		if (error) {
 			dev_dbg(&client->dev,
 				"Unable to claim irq %d; error %d\n",
-				chip->irqnum, error);
+				client->irq, error);
 			goto fail1;
 		}
 	}
@@ -297,10 +292,8 @@
 	return 0;
 
 fail2:
-	if (!chip->use_polling) {
-		free_irq(chip->irqnum, chip);
-		enable_irq(chip->irqnum);
-	}
+	if (!chip->use_polling)
+		free_irq(client->irq, chip);
 fail1:
 	input_free_device(input);
 	kfree(chip);
@@ -311,10 +304,8 @@
 {
 	struct tca6416_keypad_chip *chip = i2c_get_clientdata(client);
 
-	if (!chip->use_polling) {
-		free_irq(chip->irqnum, chip);
-		enable_irq(chip->irqnum);
-	}
+	if (!chip->use_polling)
+		free_irq(client->irq, chip);
 
 	input_unregister_device(chip->input);
 	kfree(chip);
@@ -326,10 +317,9 @@
 static int tca6416_keypad_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
-	struct tca6416_keypad_chip *chip = i2c_get_clientdata(client);
 
 	if (device_may_wakeup(dev))
-		enable_irq_wake(chip->irqnum);
+		enable_irq_wake(client->irq);
 
 	return 0;
 }
@@ -337,10 +327,9 @@
 static int tca6416_keypad_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
-	struct tca6416_keypad_chip *chip = i2c_get_clientdata(client);
 
 	if (device_may_wakeup(dev))
-		disable_irq_wake(chip->irqnum);
+		disable_irq_wake(client->irq);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/Kconfig
@@ -330,7 +330,7 @@
 
 config INPUT_WISTRON_BTNS
 	tristate "x86 Wistron laptop button interface"
-	depends on X86_32
+	depends on X86_32 && !UML
 	select INPUT_SPARSEKMAP
 	select NEW_LEDS
 	select LEDS_CLASS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/adxl34x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/adxl34x.c
@@ -811,8 +811,7 @@
 	AC_WRITE(ac, POWER_CTL, 0);
 
 	err = request_threaded_irq(ac->irq, NULL, adxl34x_irq,
-				   IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
-				   dev_name(dev), ac);
+				   IRQF_ONESHOT, dev_name(dev), ac);
 	if (err) {
 		dev_err(dev, "irq %d busy?\n", ac->irq);
 		goto err_free_mem;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/ariel-pwrbutton.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/ariel-pwrbutton.c
@@ -149,12 +149,19 @@
 };
 MODULE_DEVICE_TABLE(of, ariel_pwrbutton_of_match);
 
+static const struct spi_device_id ariel_pwrbutton_spi_ids[] = {
+	{ .name = "wyse-ariel-ec-input" },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ariel_pwrbutton_spi_ids);
+
 static struct spi_driver ariel_pwrbutton_driver = {
 	.driver = {
 		.name = "dell-wyse-ariel-ec-input",
 		.of_match_table = ariel_pwrbutton_of_match,
 	},
 	.probe = ariel_pwrbutton_probe,
+	.id_table = ariel_pwrbutton_spi_ids,
 };
 module_spi_driver(ariel_pwrbutton_driver);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/cpcap-pwrbutton.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/cpcap-pwrbutton.c
@@ -54,9 +54,13 @@
 static int cpcap_power_button_probe(struct platform_device *pdev)
 {
 	struct cpcap_power_button *button;
-	int irq = platform_get_irq(pdev, 0);
+	int irq;
 	int err;
 
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
 	button = devm_kmalloc(&pdev->dev, sizeof(*button), GFP_KERNEL);
 	if (!button)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/drv260x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/drv260x.c
@@ -435,6 +435,7 @@
 	}
 
 	do {
+		usleep_range(15000, 15500);
 		error = regmap_read(haptics->regmap, DRV260X_GO, &cal_buf);
 		if (error) {
 			dev_err(&haptics->client->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/ims-pcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/ims-pcu.c
@@ -42,8 +42,8 @@
 #define IMS_PCU_PART_NUMBER_LEN		15
 #define IMS_PCU_SERIAL_NUMBER_LEN	8
 #define IMS_PCU_DOM_LEN			8
-#define IMS_PCU_FW_VERSION_LEN		(9 + 1)
-#define IMS_PCU_BL_VERSION_LEN		(9 + 1)
+#define IMS_PCU_FW_VERSION_LEN		16
+#define IMS_PCU_BL_VERSION_LEN		16
 #define IMS_PCU_BL_RESET_REASON_LEN	(2 + 1)
 
 #define IMS_PCU_PCU_B_DEVICE_ID		5
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/iqs269a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/iqs269a.c
@@ -9,6 +9,7 @@
  * axial sliders presented by the device.
  */
 
+#include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/err.h>
@@ -96,8 +97,6 @@
 #define IQS269_MISC_B_TRACKING_UI_ENABLE	BIT(4)
 #define IQS269_MISC_B_FILT_STR_SLIDER		GENMASK(1, 0)
 
-#define IQS269_CHx_SETTINGS			0x8C
-
 #define IQS269_CHx_ENG_A_MEAS_CAP_SIZE		BIT(15)
 #define IQS269_CHx_ENG_A_RX_GND_INACTIVE	BIT(13)
 #define IQS269_CHx_ENG_A_LOCAL_CAP_SIZE		BIT(12)
@@ -146,14 +145,7 @@
 #define IQS269_NUM_CH				8
 #define IQS269_NUM_SL				2
 
-#define IQS269_ATI_POLL_SLEEP_US		(iqs269->delay_mult * 10000)
-#define IQS269_ATI_POLL_TIMEOUT_US		(iqs269->delay_mult * 500000)
-#define IQS269_ATI_STABLE_DELAY_MS		(iqs269->delay_mult * 150)
-
-#define IQS269_PWR_MODE_POLL_SLEEP_US		IQS269_ATI_POLL_SLEEP_US
-#define IQS269_PWR_MODE_POLL_TIMEOUT_US		IQS269_ATI_POLL_TIMEOUT_US
-
-#define iqs269_irq_wait()			usleep_range(100, 150)
+#define iqs269_irq_wait()			usleep_range(200, 250)
 
 enum iqs269_local_cap_size {
 	IQS269_LOCAL_CAP_SIZE_0,
@@ -245,6 +237,18 @@
 	u8 padding;
 } __packed;
 
+struct iqs269_ch_reg {
+	u8 rx_enable;
+	u8 tx_enable;
+	__be16 engine_a;
+	__be16 engine_b;
+	__be16 ati_comp;
+	u8 thresh[3];
+	u8 hyst;
+	u8 assoc_select;
+	u8 assoc_weight;
+} __packed;
+
 struct iqs269_sys_reg {
 	__be16 general;
 	u8 active;
@@ -266,18 +270,7 @@
 	u8 timeout_swipe;
 	u8 thresh_swipe;
 	u8 redo_ati;
-} __packed;
-
-struct iqs269_ch_reg {
-	u8 rx_enable;
-	u8 tx_enable;
-	__be16 engine_a;
-	__be16 engine_b;
-	__be16 ati_comp;
-	u8 thresh[3];
-	u8 hyst;
-	u8 assoc_select;
-	u8 assoc_weight;
+	struct iqs269_ch_reg ch_reg[IQS269_NUM_CH];
 } __packed;
 
 struct iqs269_flags {
@@ -292,13 +285,11 @@
 	struct regmap *regmap;
 	struct mutex lock;
 	struct iqs269_switch_desc switches[ARRAY_SIZE(iqs269_events)];
-	struct iqs269_ch_reg ch_reg[IQS269_NUM_CH];
 	struct iqs269_sys_reg sys_reg;
+	struct completion ati_done;
 	struct input_dev *keypad;
 	struct input_dev *slider[IQS269_NUM_SL];
 	unsigned int keycode[ARRAY_SIZE(iqs269_events) * IQS269_NUM_CH];
-	unsigned int suspend_mode;
-	unsigned int delay_mult;
 	unsigned int ch_num;
 	bool hall_enable;
 	bool ati_current;
@@ -307,6 +298,7 @@
 static int iqs269_ati_mode_set(struct iqs269_private *iqs269,
 			       unsigned int ch_num, unsigned int mode)
 {
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	u16 engine_a;
 
 	if (ch_num >= IQS269_NUM_CH)
@@ -317,12 +309,12 @@
 
 	mutex_lock(&iqs269->lock);
 
-	engine_a = be16_to_cpu(iqs269->ch_reg[ch_num].engine_a);
+	engine_a = be16_to_cpu(ch_reg[ch_num].engine_a);
 
 	engine_a &= ~IQS269_CHx_ENG_A_ATI_MODE_MASK;
 	engine_a |= (mode << IQS269_CHx_ENG_A_ATI_MODE_SHIFT);
 
-	iqs269->ch_reg[ch_num].engine_a = cpu_to_be16(engine_a);
+	ch_reg[ch_num].engine_a = cpu_to_be16(engine_a);
 	iqs269->ati_current = false;
 
 	mutex_unlock(&iqs269->lock);
@@ -333,13 +325,14 @@
 static int iqs269_ati_mode_get(struct iqs269_private *iqs269,
 			       unsigned int ch_num, unsigned int *mode)
 {
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	u16 engine_a;
 
 	if (ch_num >= IQS269_NUM_CH)
 		return -EINVAL;
 
 	mutex_lock(&iqs269->lock);
-	engine_a = be16_to_cpu(iqs269->ch_reg[ch_num].engine_a);
+	engine_a = be16_to_cpu(ch_reg[ch_num].engine_a);
 	mutex_unlock(&iqs269->lock);
 
 	engine_a &= IQS269_CHx_ENG_A_ATI_MODE_MASK;
@@ -351,6 +344,7 @@
 static int iqs269_ati_base_set(struct iqs269_private *iqs269,
 			       unsigned int ch_num, unsigned int base)
 {
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	u16 engine_b;
 
 	if (ch_num >= IQS269_NUM_CH)
@@ -379,12 +373,12 @@
 
 	mutex_lock(&iqs269->lock);
 
-	engine_b = be16_to_cpu(iqs269->ch_reg[ch_num].engine_b);
+	engine_b = be16_to_cpu(ch_reg[ch_num].engine_b);
 
 	engine_b &= ~IQS269_CHx_ENG_B_ATI_BASE_MASK;
 	engine_b |= base;
 
-	iqs269->ch_reg[ch_num].engine_b = cpu_to_be16(engine_b);
+	ch_reg[ch_num].engine_b = cpu_to_be16(engine_b);
 	iqs269->ati_current = false;
 
 	mutex_unlock(&iqs269->lock);
@@ -395,13 +389,14 @@
 static int iqs269_ati_base_get(struct iqs269_private *iqs269,
 			       unsigned int ch_num, unsigned int *base)
 {
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	u16 engine_b;
 
 	if (ch_num >= IQS269_NUM_CH)
 		return -EINVAL;
 
 	mutex_lock(&iqs269->lock);
-	engine_b = be16_to_cpu(iqs269->ch_reg[ch_num].engine_b);
+	engine_b = be16_to_cpu(ch_reg[ch_num].engine_b);
 	mutex_unlock(&iqs269->lock);
 
 	switch (engine_b & IQS269_CHx_ENG_B_ATI_BASE_MASK) {
@@ -429,6 +424,7 @@
 static int iqs269_ati_target_set(struct iqs269_private *iqs269,
 				 unsigned int ch_num, unsigned int target)
 {
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	u16 engine_b;
 
 	if (ch_num >= IQS269_NUM_CH)
@@ -439,12 +435,12 @@
 
 	mutex_lock(&iqs269->lock);
 
-	engine_b = be16_to_cpu(iqs269->ch_reg[ch_num].engine_b);
+	engine_b = be16_to_cpu(ch_reg[ch_num].engine_b);
 
 	engine_b &= ~IQS269_CHx_ENG_B_ATI_TARGET_MASK;
 	engine_b |= target / 32;
 
-	iqs269->ch_reg[ch_num].engine_b = cpu_to_be16(engine_b);
+	ch_reg[ch_num].engine_b = cpu_to_be16(engine_b);
 	iqs269->ati_current = false;
 
 	mutex_unlock(&iqs269->lock);
@@ -455,13 +451,14 @@
 static int iqs269_ati_target_get(struct iqs269_private *iqs269,
 				 unsigned int ch_num, unsigned int *target)
 {
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	u16 engine_b;
 
 	if (ch_num >= IQS269_NUM_CH)
 		return -EINVAL;
 
 	mutex_lock(&iqs269->lock);
-	engine_b = be16_to_cpu(iqs269->ch_reg[ch_num].engine_b);
+	engine_b = be16_to_cpu(ch_reg[ch_num].engine_b);
 	mutex_unlock(&iqs269->lock);
 
 	*target = (engine_b & IQS269_CHx_ENG_B_ATI_TARGET_MASK) * 32;
@@ -531,13 +528,7 @@
 	if (fwnode_property_present(ch_node, "azoteq,slider1-select"))
 		iqs269->sys_reg.slider_select[1] |= BIT(reg);
 
-	ch_reg = &iqs269->ch_reg[reg];
-
-	error = regmap_raw_read(iqs269->regmap,
-				IQS269_CHx_SETTINGS + reg * sizeof(*ch_reg) / 2,
-				ch_reg, sizeof(*ch_reg));
-	if (error)
-		return error;
+	ch_reg = &iqs269->sys_reg.ch_reg[reg];
 
 	error = iqs269_parse_mask(ch_node, "azoteq,rx-enable",
 				  &ch_reg->rx_enable);
@@ -694,6 +685,7 @@
 				dev_err(&client->dev,
 					"Invalid channel %u threshold: %u\n",
 					reg, val);
+				fwnode_handle_put(ev_node);
 				return -EINVAL;
 			}
 
@@ -707,6 +699,7 @@
 				dev_err(&client->dev,
 					"Invalid channel %u hysteresis: %u\n",
 					reg, val);
+				fwnode_handle_put(ev_node);
 				return -EINVAL;
 			}
 
@@ -721,8 +714,16 @@
 			}
 		}
 
-		if (fwnode_property_read_u32(ev_node, "linux,code", &val))
+		error = fwnode_property_read_u32(ev_node, "linux,code", &val);
+		fwnode_handle_put(ev_node);
+		if (error == -EINVAL) {
 			continue;
+		} else if (error) {
+			dev_err(&client->dev,
+				"Failed to read channel %u code: %d\n", reg,
+				error);
+			return error;
+		}
 
 		switch (reg) {
 		case IQS269_CHx_HALL_ACTIVE:
@@ -759,17 +760,6 @@
 	iqs269->hall_enable = device_property_present(&client->dev,
 						      "azoteq,hall-enable");
 
-	if (!device_property_read_u32(&client->dev, "azoteq,suspend-mode",
-				      &val)) {
-		if (val > IQS269_SYS_SETTINGS_PWR_MODE_MAX) {
-			dev_err(&client->dev, "Invalid suspend mode: %u\n",
-				val);
-			return -EINVAL;
-		}
-
-		iqs269->suspend_mode = val;
-	}
-
 	error = regmap_raw_read(iqs269->regmap, IQS269_SYS_SETTINGS, sys_reg,
 				sizeof(*sys_reg));
 	if (error)
@@ -980,13 +970,8 @@
 
 	general = be16_to_cpu(sys_reg->general);
 
-	if (device_property_present(&client->dev, "azoteq,clk-div")) {
+	if (device_property_present(&client->dev, "azoteq,clk-div"))
 		general |= IQS269_SYS_SETTINGS_CLK_DIV;
-		iqs269->delay_mult = 4;
-	} else {
-		general &= ~IQS269_SYS_SETTINGS_CLK_DIV;
-		iqs269->delay_mult = 1;
-	}
 
 	/*
 	 * Configure the device to automatically switch between normal and low-
@@ -997,6 +982,17 @@
 	general &= ~IQS269_SYS_SETTINGS_DIS_AUTO;
 	general &= ~IQS269_SYS_SETTINGS_PWR_MODE_MASK;
 
+	if (!device_property_read_u32(&client->dev, "azoteq,suspend-mode",
+				      &val)) {
+		if (val > IQS269_SYS_SETTINGS_PWR_MODE_MAX) {
+			dev_err(&client->dev, "Invalid suspend mode: %u\n",
+				val);
+			return -EINVAL;
+		}
+
+		general |= (val << IQS269_SYS_SETTINGS_PWR_MODE_SHIFT);
+	}
+
 	if (!device_property_read_u32(&client->dev, "azoteq,ulp-update",
 				      &val)) {
 		if (val > IQS269_SYS_SETTINGS_ULP_UPDATE_MAX) {
@@ -1032,10 +1028,7 @@
 
 static int iqs269_dev_init(struct iqs269_private *iqs269)
 {
-	struct iqs269_sys_reg *sys_reg = &iqs269->sys_reg;
-	struct iqs269_ch_reg *ch_reg;
-	unsigned int val;
-	int error, i;
+	int error;
 
 	mutex_lock(&iqs269->lock);
 
@@ -1045,38 +1038,17 @@
 	if (error)
 		goto err_mutex;
 
-	for (i = 0; i < IQS269_NUM_CH; i++) {
-		if (!(sys_reg->active & BIT(i)))
-			continue;
-
-		ch_reg = &iqs269->ch_reg[i];
-
-		error = regmap_raw_write(iqs269->regmap,
-					 IQS269_CHx_SETTINGS + i *
-					 sizeof(*ch_reg) / 2, ch_reg,
-					 sizeof(*ch_reg));
-		if (error)
-			goto err_mutex;
-	}
-
-	/*
-	 * The REDO-ATI and ATI channel selection fields must be written in the
-	 * same block write, so every field between registers 0x80 through 0x8B
-	 * (inclusive) must be written as well.
-	 */
-	error = regmap_raw_write(iqs269->regmap, IQS269_SYS_SETTINGS, sys_reg,
-				 sizeof(*sys_reg));
+	error = regmap_raw_write(iqs269->regmap, IQS269_SYS_SETTINGS,
+				 &iqs269->sys_reg, sizeof(iqs269->sys_reg));
 	if (error)
 		goto err_mutex;
 
-	error = regmap_read_poll_timeout(iqs269->regmap, IQS269_SYS_FLAGS, val,
-					!(val & IQS269_SYS_FLAGS_IN_ATI),
-					 IQS269_ATI_POLL_SLEEP_US,
-					 IQS269_ATI_POLL_TIMEOUT_US);
-	if (error)
-		goto err_mutex;
+	/*
+	 * The following delay gives the device time to deassert its RDY output
+	 * so as to prevent an interrupt from being serviced prematurely.
+	 */
+	usleep_range(2000, 2100);
 
-	msleep(IQS269_ATI_STABLE_DELAY_MS);
 	iqs269->ati_current = true;
 
 err_mutex:
@@ -1088,10 +1060,8 @@
 static int iqs269_input_init(struct iqs269_private *iqs269)
 {
 	struct i2c_client *client = iqs269->client;
-	struct iqs269_flags flags;
 	unsigned int sw_code, keycode;
 	int error, i, j;
-	u8 dir_mask, state;
 
 	iqs269->keypad = devm_input_allocate_device(&client->dev);
 	if (!iqs269->keypad)
@@ -1104,23 +1074,7 @@
 	iqs269->keypad->name = "iqs269a_keypad";
 	iqs269->keypad->id.bustype = BUS_I2C;
 
-	if (iqs269->hall_enable) {
-		error = regmap_raw_read(iqs269->regmap, IQS269_SYS_FLAGS,
-					&flags, sizeof(flags));
-		if (error) {
-			dev_err(&client->dev,
-				"Failed to read initial status: %d\n", error);
-			return error;
-		}
-	}
-
 	for (i = 0; i < ARRAY_SIZE(iqs269_events); i++) {
-		dir_mask = flags.states[IQS269_ST_OFFS_DIR];
-		if (!iqs269_events[i].dir_up)
-			dir_mask = ~dir_mask;
-
-		state = flags.states[iqs269_events[i].st_offs] & dir_mask;
-
 		sw_code = iqs269->switches[i].code;
 
 		for (j = 0; j < IQS269_NUM_CH; j++) {
@@ -1133,13 +1087,9 @@
 			switch (j) {
 			case IQS269_CHx_HALL_ACTIVE:
 				if (iqs269->hall_enable &&
-				    iqs269->switches[i].enabled) {
+				    iqs269->switches[i].enabled)
 					input_set_capability(iqs269->keypad,
 							     EV_SW, sw_code);
-					input_report_switch(iqs269->keypad,
-							    sw_code,
-							    state & BIT(j));
-				}
 				fallthrough;
 
 			case IQS269_CHx_HALL_INACTIVE:
@@ -1155,14 +1105,6 @@
 		}
 	}
 
-	input_sync(iqs269->keypad);
-
-	error = input_register_device(iqs269->keypad);
-	if (error) {
-		dev_err(&client->dev, "Failed to register keypad: %d\n", error);
-		return error;
-	}
-
 	for (i = 0; i < IQS269_NUM_SL; i++) {
 		if (!iqs269->sys_reg.slider_select[i])
 			continue;
@@ -1222,6 +1164,9 @@
 		return error;
 	}
 
+	if (be16_to_cpu(flags.system) & IQS269_SYS_FLAGS_IN_ATI)
+		return 0;
+
 	error = regmap_raw_read(iqs269->regmap, IQS269_SLIDER_X, slider_x,
 				sizeof(slider_x));
 	if (error) {
@@ -1284,6 +1229,12 @@
 
 	input_sync(iqs269->keypad);
 
+	/*
+	 * The following completion signals that ATI has finished, any initial
+	 * switch states have been reported and the keypad can be registered.
+	 */
+	complete_all(&iqs269->ati_done);
+
 	return 0;
 }
 
@@ -1315,6 +1266,9 @@
 	if (!iqs269->ati_current || iqs269->hall_enable)
 		return -EPERM;
 
+	if (!completion_done(&iqs269->ati_done))
+		return -EBUSY;
+
 	/*
 	 * Unsolicited I2C communication prompts the device to assert its RDY
 	 * pin, so disable the interrupt line until the operation is finished
@@ -1339,6 +1293,7 @@
 			     struct device_attribute *attr, char *buf)
 {
 	struct iqs269_private *iqs269 = dev_get_drvdata(dev);
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	struct i2c_client *client = iqs269->client;
 	unsigned int val;
 	int error;
@@ -1353,8 +1308,8 @@
 	if (error)
 		return error;
 
-	switch (iqs269->ch_reg[IQS269_CHx_HALL_ACTIVE].rx_enable &
-		iqs269->ch_reg[IQS269_CHx_HALL_INACTIVE].rx_enable) {
+	switch (ch_reg[IQS269_CHx_HALL_ACTIVE].rx_enable &
+		ch_reg[IQS269_CHx_HALL_INACTIVE].rx_enable) {
 	case IQS269_HALL_PAD_R:
 		val &= IQS269_CAL_DATA_A_HALL_BIN_R_MASK;
 		val >>= IQS269_CAL_DATA_A_HALL_BIN_R_SHIFT;
@@ -1434,9 +1389,10 @@
 			      struct device_attribute *attr, char *buf)
 {
 	struct iqs269_private *iqs269 = dev_get_drvdata(dev);
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 
 	return scnprintf(buf, PAGE_SIZE, "%u\n",
-			 iqs269->ch_reg[iqs269->ch_num].rx_enable);
+			 ch_reg[iqs269->ch_num].rx_enable);
 }
 
 static ssize_t rx_enable_store(struct device *dev,
@@ -1444,6 +1400,7 @@
 			       size_t count)
 {
 	struct iqs269_private *iqs269 = dev_get_drvdata(dev);
+	struct iqs269_ch_reg *ch_reg = iqs269->sys_reg.ch_reg;
 	unsigned int val;
 	int error;
 
@@ -1456,7 +1413,7 @@
 
 	mutex_lock(&iqs269->lock);
 
-	iqs269->ch_reg[iqs269->ch_num].rx_enable = val;
+	ch_reg[iqs269->ch_num].rx_enable = val;
 	iqs269->ati_current = false;
 
 	mutex_unlock(&iqs269->lock);
@@ -1568,7 +1525,9 @@
 {
 	struct iqs269_private *iqs269 = dev_get_drvdata(dev);
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n", iqs269->ati_current);
+	return scnprintf(buf, PAGE_SIZE, "%u\n",
+			 iqs269->ati_current &&
+			 completion_done(&iqs269->ati_done));
 }
 
 static ssize_t ati_trigger_store(struct device *dev,
@@ -1588,6 +1547,7 @@
 		return count;
 
 	disable_irq(client->irq);
+	reinit_completion(&iqs269->ati_done);
 
 	error = iqs269_dev_init(iqs269);
 
@@ -1597,6 +1557,10 @@
 	if (error)
 		return error;
 
+	if (!wait_for_completion_timeout(&iqs269->ati_done,
+					 msecs_to_jiffies(2000)))
+		return -ETIMEDOUT;
+
 	return count;
 }
 
@@ -1655,6 +1619,7 @@
 	}
 
 	mutex_init(&iqs269->lock);
+	init_completion(&iqs269->ati_done);
 
 	error = regmap_raw_read(iqs269->regmap, IQS269_VER_INFO, &ver_info,
 				sizeof(ver_info));
@@ -1690,6 +1655,22 @@
 		return error;
 	}
 
+	if (!wait_for_completion_timeout(&iqs269->ati_done,
+					 msecs_to_jiffies(2000))) {
+		dev_err(&client->dev, "Failed to complete ATI\n");
+		return -ETIMEDOUT;
+	}
+
+	/*
+	 * The keypad may include one or more switches and is not registered
+	 * until ATI is complete and the initial switch states are read.
+	 */
+	error = input_register_device(iqs269->keypad);
+	if (error) {
+		dev_err(&client->dev, "Failed to register keypad: %d\n", error);
+		return error;
+	}
+
 	error = devm_device_add_group(&client->dev, &iqs269_attr_group);
 	if (error)
 		dev_err(&client->dev, "Failed to add attributes: %d\n", error);
@@ -1697,113 +1678,61 @@
 	return error;
 }
 
-static int __maybe_unused iqs269_suspend(struct device *dev)
+static u16 iqs269_general_get(struct iqs269_private *iqs269)
+{
+	u16 general = be16_to_cpu(iqs269->sys_reg.general);
+
+	general &= ~IQS269_SYS_SETTINGS_REDO_ATI;
+	general &= ~IQS269_SYS_SETTINGS_ACK_RESET;
+
+	return general | IQS269_SYS_SETTINGS_DIS_AUTO;
+}
+
+static int iqs269_suspend(struct device *dev)
 {
 	struct iqs269_private *iqs269 = dev_get_drvdata(dev);
 	struct i2c_client *client = iqs269->client;
-	unsigned int val;
 	int error;
+	u16 general = iqs269_general_get(iqs269);
 
-	if (!iqs269->suspend_mode)
+	if (!(general & IQS269_SYS_SETTINGS_PWR_MODE_MASK))
 		return 0;
 
 	disable_irq(client->irq);
 
-	/*
-	 * Automatic power mode switching must be disabled before the device is
-	 * forced into any particular power mode. In this case, the device will
-	 * transition into normal-power mode.
-	 */
-	error = regmap_update_bits(iqs269->regmap, IQS269_SYS_SETTINGS,
-				   IQS269_SYS_SETTINGS_DIS_AUTO, ~0);
-	if (error)
-		goto err_irq;
-
-	/*
-	 * The following check ensures the device has completed its transition
-	 * into normal-power mode before a manual mode switch is performed.
-	 */
-	error = regmap_read_poll_timeout(iqs269->regmap, IQS269_SYS_FLAGS, val,
-					!(val & IQS269_SYS_FLAGS_PWR_MODE_MASK),
-					 IQS269_PWR_MODE_POLL_SLEEP_US,
-					 IQS269_PWR_MODE_POLL_TIMEOUT_US);
-	if (error)
-		goto err_irq;
-
-	error = regmap_update_bits(iqs269->regmap, IQS269_SYS_SETTINGS,
-				   IQS269_SYS_SETTINGS_PWR_MODE_MASK,
-				   iqs269->suspend_mode <<
-				   IQS269_SYS_SETTINGS_PWR_MODE_SHIFT);
-	if (error)
-		goto err_irq;
+	error = regmap_write(iqs269->regmap, IQS269_SYS_SETTINGS, general);
 
-	/*
-	 * This last check ensures the device has completed its transition into
-	 * the desired power mode to prevent any spurious interrupts from being
-	 * triggered after iqs269_suspend has already returned.
-	 */
-	error = regmap_read_poll_timeout(iqs269->regmap, IQS269_SYS_FLAGS, val,
-					 (val & IQS269_SYS_FLAGS_PWR_MODE_MASK)
-					 == (iqs269->suspend_mode <<
-					     IQS269_SYS_FLAGS_PWR_MODE_SHIFT),
-					 IQS269_PWR_MODE_POLL_SLEEP_US,
-					 IQS269_PWR_MODE_POLL_TIMEOUT_US);
-
-err_irq:
 	iqs269_irq_wait();
 	enable_irq(client->irq);
 
 	return error;
 }
 
-static int __maybe_unused iqs269_resume(struct device *dev)
+static int iqs269_resume(struct device *dev)
 {
 	struct iqs269_private *iqs269 = dev_get_drvdata(dev);
 	struct i2c_client *client = iqs269->client;
-	unsigned int val;
 	int error;
+	u16 general = iqs269_general_get(iqs269);
 
-	if (!iqs269->suspend_mode)
+	if (!(general & IQS269_SYS_SETTINGS_PWR_MODE_MASK))
 		return 0;
 
 	disable_irq(client->irq);
 
-	error = regmap_update_bits(iqs269->regmap, IQS269_SYS_SETTINGS,
-				   IQS269_SYS_SETTINGS_PWR_MODE_MASK, 0);
-	if (error)
-		goto err_irq;
-
-	/*
-	 * This check ensures the device has returned to normal-power mode
-	 * before automatic power mode switching is re-enabled.
-	 */
-	error = regmap_read_poll_timeout(iqs269->regmap, IQS269_SYS_FLAGS, val,
-					!(val & IQS269_SYS_FLAGS_PWR_MODE_MASK),
-					 IQS269_PWR_MODE_POLL_SLEEP_US,
-					 IQS269_PWR_MODE_POLL_TIMEOUT_US);
-	if (error)
-		goto err_irq;
-
-	error = regmap_update_bits(iqs269->regmap, IQS269_SYS_SETTINGS,
-				   IQS269_SYS_SETTINGS_DIS_AUTO, 0);
-	if (error)
-		goto err_irq;
-
-	/*
-	 * This step reports any events that may have been "swallowed" as a
-	 * result of polling PWR_MODE (which automatically acknowledges any
-	 * pending interrupts).
-	 */
-	error = iqs269_report(iqs269);
+	error = regmap_write(iqs269->regmap, IQS269_SYS_SETTINGS,
+			     general & ~IQS269_SYS_SETTINGS_PWR_MODE_MASK);
+	if (!error)
+		error = regmap_write(iqs269->regmap, IQS269_SYS_SETTINGS,
+				     general & ~IQS269_SYS_SETTINGS_DIS_AUTO);
 
-err_irq:
 	iqs269_irq_wait();
 	enable_irq(client->irq);
 
 	return error;
 }
 
-static SIMPLE_DEV_PM_OPS(iqs269_pm, iqs269_suspend, iqs269_resume);
+static DEFINE_SIMPLE_DEV_PM_OPS(iqs269_pm, iqs269_suspend, iqs269_resume);
 
 static const struct of_device_id iqs269_of_match[] = {
 	{ .compatible = "azoteq,iqs269a" },
@@ -1815,7 +1744,7 @@
 	.driver = {
 		.name = "iqs269a",
 		.of_match_table = iqs269_of_match,
-		.pm = &iqs269_pm,
+		.pm = pm_sleep_ptr(&iqs269_pm),
 	},
 	.probe_new = iqs269_probe,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/iqs626a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/iqs626a.c
@@ -456,9 +456,10 @@
 	unsigned int suspend_mode;
 };
 
-static int iqs626_parse_events(struct iqs626_private *iqs626,
-			       const struct fwnode_handle *ch_node,
-			       enum iqs626_ch_id ch_id)
+static noinline_for_stack int
+iqs626_parse_events(struct iqs626_private *iqs626,
+		    const struct fwnode_handle *ch_node,
+		    enum iqs626_ch_id ch_id)
 {
 	struct iqs626_sys_reg *sys_reg = &iqs626->sys_reg;
 	struct i2c_client *client = iqs626->client;
@@ -604,9 +605,10 @@
 	return 0;
 }
 
-static int iqs626_parse_ati_target(struct iqs626_private *iqs626,
-				   const struct fwnode_handle *ch_node,
-				   enum iqs626_ch_id ch_id)
+static noinline_for_stack int
+iqs626_parse_ati_target(struct iqs626_private *iqs626,
+			const struct fwnode_handle *ch_node,
+			enum iqs626_ch_id ch_id)
 {
 	struct iqs626_sys_reg *sys_reg = &iqs626->sys_reg;
 	struct i2c_client *client = iqs626->client;
@@ -885,9 +887,10 @@
 	return 0;
 }
 
-static int iqs626_parse_channel(struct iqs626_private *iqs626,
-				const struct fwnode_handle *ch_node,
-				enum iqs626_ch_id ch_id)
+static noinline_for_stack int
+iqs626_parse_channel(struct iqs626_private *iqs626,
+		     const struct fwnode_handle *ch_node,
+		     enum iqs626_ch_id ch_id)
 {
 	struct iqs626_sys_reg *sys_reg = &iqs626->sys_reg;
 	struct i2c_client *client = iqs626->client;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/pm8xxx-vibrator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/pm8xxx-vibrator.c
@@ -14,7 +14,8 @@
 
 #define VIB_MAX_LEVEL_mV	(3100)
 #define VIB_MIN_LEVEL_mV	(1200)
-#define VIB_MAX_LEVELS		(VIB_MAX_LEVEL_mV - VIB_MIN_LEVEL_mV)
+#define VIB_PER_STEP_mV		(100)
+#define VIB_MAX_LEVELS		(VIB_MAX_LEVEL_mV - VIB_MIN_LEVEL_mV + VIB_PER_STEP_mV)
 
 #define MAX_FF_SPEED		0xff
 
@@ -118,10 +119,10 @@
 		vib->active = true;
 		vib->level = ((VIB_MAX_LEVELS * vib->speed) / MAX_FF_SPEED) +
 						VIB_MIN_LEVEL_mV;
-		vib->level /= 100;
+		vib->level /= VIB_PER_STEP_mV;
 	} else {
 		vib->active = false;
-		vib->level = VIB_MIN_LEVEL_mV / 100;
+		vib->level = VIB_MIN_LEVEL_mV / VIB_PER_STEP_mV;
 	}
 
 	pm8xxx_vib_set(vib, vib->active);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/powermate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/powermate.c
@@ -425,6 +425,7 @@
 		pm->requires_update = 0;
 		usb_kill_urb(pm->irq);
 		input_unregister_device(pm->input);
+		usb_kill_urb(pm->config);
 		usb_free_urb(pm->irq);
 		usb_free_urb(pm->config);
 		powermate_free_buffers(interface_to_usbdev(intf), pm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/rk805-pwrkey.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/rk805-pwrkey.c
@@ -98,6 +98,7 @@
 };
 module_platform_driver(rk805_pwrkey_driver);
 
+MODULE_ALIAS("platform:rk805-pwrkey");
 MODULE_AUTHOR("Joseph Chen <chenjh@rock-chips.com>");
 MODULE_DESCRIPTION("RK805 PMIC Power Key driver");
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/soc_button_array.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/soc_button_array.c
@@ -18,6 +18,10 @@
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
 
+static bool use_low_level_irq;
+module_param(use_low_level_irq, bool, 0444);
+MODULE_PARM_DESC(use_low_level_irq, "Use low-level triggered IRQ instead of edge triggered");
+
 struct soc_button_info {
 	const char *name;
 	int acpi_index;
@@ -74,6 +78,13 @@
 		},
 	},
 	{
+		/* Acer Switch V 10 SW5-017, same issue as Acer Switch 10 SW5-012. */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "SW5-017"),
+		},
+	},
+	{
 		/*
 		 * Acer One S1003. _LID method messes with power-button GPIO
 		 * IRQ settings, leading to a non working power-button.
@@ -85,19 +96,40 @@
 	},
 	{
 		/*
-		 * Lenovo Yoga Tab2 1051L, something messes with the home-button
+		 * Lenovo Yoga Tab2 1051F/1051L, something messes with the home-button
 		 * IRQ settings, leading to a non working home-button.
 		 */
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
 			DMI_MATCH(DMI_PRODUCT_NAME, "60073"),
-			DMI_MATCH(DMI_PRODUCT_VERSION, "1051L"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "1051"),
 		},
 	},
 	{} /* Terminating entry */
 };
 
 /*
+ * Some devices have a wrong entry which points to a GPIO which is
+ * required in another driver, so this driver must not claim it.
+ */
+static const struct dmi_system_id dmi_invalid_acpi_index[] = {
+	{
+		/*
+		 * Lenovo Yoga Book X90F / X90L, the PNP0C40 home button entry
+		 * points to a GPIO which is not a home button and which is
+		 * required by the lenovo-yogabook driver.
+		 */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Intel Corporation"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "CHERRYVIEW D1 PLATFORM"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "YETI-11"),
+		},
+		.driver_data = (void *)1l,
+	},
+	{} /* Terminating entry */
+};
+
+/*
  * Get the Nth GPIO number from the ACPI object.
  */
 static int soc_button_lookup_gpio(struct device *dev, int acpi_index,
@@ -126,6 +158,8 @@
 	struct platform_device *pd;
 	struct gpio_keys_button *gpio_keys;
 	struct gpio_keys_platform_data *gpio_keys_pdata;
+	const struct dmi_system_id *dmi_id;
+	int invalid_acpi_index = -1;
 	int error, gpio, irq;
 	int n_buttons = 0;
 
@@ -143,10 +177,17 @@
 	gpio_keys = (void *)(gpio_keys_pdata + 1);
 	n_buttons = 0;
 
+	dmi_id = dmi_first_match(dmi_invalid_acpi_index);
+	if (dmi_id)
+		invalid_acpi_index = (long)dmi_id->driver_data;
+
 	for (info = button_info; info->name; info++) {
 		if (info->autorepeat != autorepeat)
 			continue;
 
+		if (info->acpi_index == invalid_acpi_index)
+			continue;
+
 		error = soc_button_lookup_gpio(&pdev->dev, info->acpi_index, &gpio, &irq);
 		if (error || irq < 0) {
 			/*
@@ -164,7 +205,8 @@
 		}
 
 		/* See dmi_use_low_level_irq[] comment */
-		if (!autorepeat && dmi_check_system(dmi_use_low_level_irq)) {
+		if (!autorepeat && (use_low_level_irq ||
+				    dmi_check_system(dmi_use_low_level_irq))) {
 			irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
 			gpio_keys[n_buttons].irq = irq;
 			gpio_keys[n_buttons].gpio = -ENOENT;
@@ -257,6 +299,11 @@
 		info->name = "power";
 		info->event_code = KEY_POWER;
 		info->wakeup = true;
+	} else if (upage == 0x01 && usage == 0xc6) {
+		info->name = "airplane mode switch";
+		info->event_type = EV_SW;
+		info->event_code = SW_RFKILL_ALL;
+		info->active_low = false;
 	} else if (upage == 0x01 && usage == 0xca) {
 		info->name = "rotation lock switch";
 		info->event_type = EV_SW;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/sparcspkr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/sparcspkr.c
@@ -205,6 +205,7 @@
 
 	info = &state->u.bbc;
 	info->clock_freq = of_getintprop_default(dp, "clock-frequency", 0);
+	of_node_put(dp);
 	if (!info->clock_freq)
 		goto out_free;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/misc/uinput.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/misc/uinput.c
@@ -416,6 +416,20 @@
 		return -EINVAL;
 	}
 
+	/*
+	 * Limit number of contacts to a reasonable value (100). This
+	 * ensures that we need less than 2 pages for struct input_mt
+	 * (we are not using in-kernel slot assignment so not going to
+	 * allocate memory for the "red" table), and we should have no
+	 * trouble getting this much memory.
+	 */
+	if (code == ABS_MT_SLOT && max > 99) {
+		printk(KERN_DEBUG
+		       "%s: unreasonably large number of slots requested: %d\n",
+		       UINPUT_NAME, max);
+		return -EINVAL;
+	}
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/alps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/alps.c
@@ -852,8 +852,8 @@
 			x = y = z = 0;
 
 		/* Divide 4 since trackpoint's speed is too fast */
-		input_report_rel(dev2, REL_X, (char)x / 4);
-		input_report_rel(dev2, REL_Y, -((char)y / 4));
+		input_report_rel(dev2, REL_X, (s8)x / 4);
+		input_report_rel(dev2, REL_Y, -((s8)y / 4));
 
 		psmouse_report_standard_buttons(dev2, packet[3]);
 
@@ -1104,8 +1104,8 @@
 	    ((packet[3] & 0x20) << 1);
 	z = (packet[5] & 0x3f) | ((packet[3] & 0x80) >> 1);
 
-	input_report_rel(dev2, REL_X, (char)x);
-	input_report_rel(dev2, REL_Y, -((char)y));
+	input_report_rel(dev2, REL_X, (s8)x);
+	input_report_rel(dev2, REL_Y, -((s8)y));
 	input_report_abs(dev2, ABS_PRESSURE, z);
 
 	psmouse_report_standard_buttons(dev2, packet[1]);
@@ -2294,20 +2294,20 @@
 	if (reg < 0)
 		return reg;
 
-	x_pitch = (char)(reg << 4) >> 4; /* sign extend lower 4 bits */
+	x_pitch = (s8)(reg << 4) >> 4; /* sign extend lower 4 bits */
 	x_pitch = 50 + 2 * x_pitch; /* In 0.1 mm units */
 
-	y_pitch = (char)reg >> 4; /* sign extend upper 4 bits */
+	y_pitch = (s8)reg >> 4; /* sign extend upper 4 bits */
 	y_pitch = 36 + 2 * y_pitch; /* In 0.1 mm units */
 
 	reg = alps_command_mode_read_reg(psmouse, reg_pitch + 1);
 	if (reg < 0)
 		return reg;
 
-	x_electrode = (char)(reg << 4) >> 4; /* sign extend lower 4 bits */
+	x_electrode = (s8)(reg << 4) >> 4; /* sign extend lower 4 bits */
 	x_electrode = 17 + x_electrode;
 
-	y_electrode = (char)reg >> 4; /* sign extend upper 4 bits */
+	y_electrode = (s8)reg >> 4; /* sign extend upper 4 bits */
 	y_electrode = 13 + y_electrode;
 
 	x_phys = x_pitch * (x_electrode - 1); /* In 0.1 mm units */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/appletouch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/appletouch.c
@@ -916,6 +916,8 @@
 	set_bit(BTN_TOOL_TRIPLETAP, input_dev->keybit);
 	set_bit(BTN_LEFT, input_dev->keybit);
 
+	INIT_WORK(&dev->work, atp_reinit);
+
 	error = input_register_device(dev->input);
 	if (error)
 		goto err_free_buffer;
@@ -923,8 +925,6 @@
 	/* save our data pointer in this interface device */
 	usb_set_intfdata(iface, dev);
 
-	INIT_WORK(&dev->work, atp_reinit);
-
 	return 0;
 
  err_free_buffer:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/bcm5974.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/bcm5974.c
@@ -942,17 +942,22 @@
 	if (!dev->tp_data)
 		goto err_free_bt_buffer;
 
-	if (dev->bt_urb)
+	if (dev->bt_urb) {
 		usb_fill_int_urb(dev->bt_urb, udev,
 				 usb_rcvintpipe(udev, cfg->bt_ep),
 				 dev->bt_data, dev->cfg.bt_datalen,
 				 bcm5974_irq_button, dev, 1);
 
+		dev->bt_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+	}
+
 	usb_fill_int_urb(dev->tp_urb, udev,
 			 usb_rcvintpipe(udev, cfg->tp_ep),
 			 dev->tp_data, dev->cfg.tp_datalen,
 			 bcm5974_irq_trackpad, dev, 1);
 
+	dev->tp_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+
 	/* create bcm5974 device */
 	usb_make_path(udev, dev->phys, sizeof(dev->phys));
 	strlcat(dev->phys, "/input0", sizeof(dev->phys));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/cyapa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/cyapa.c
@@ -1357,10 +1357,16 @@
 	u8 power_mode;
 	int error;
 
-	error = mutex_lock_interruptible(&cyapa->state_sync_lock);
+	error = mutex_lock_interruptible(&cyapa->input->mutex);
 	if (error)
 		return error;
 
+	error = mutex_lock_interruptible(&cyapa->state_sync_lock);
+	if (error) {
+		mutex_unlock(&cyapa->input->mutex);
+		return error;
+	}
+
 	/*
 	 * Runtime PM is enable only when device is in operational mode and
 	 * users in use, so need check it before disable it to
@@ -1395,6 +1401,8 @@
 		cyapa->irq_wake = (enable_irq_wake(client->irq) == 0);
 
 	mutex_unlock(&cyapa->state_sync_lock);
+	mutex_unlock(&cyapa->input->mutex);
+
 	return 0;
 }
 
@@ -1404,6 +1412,7 @@
 	struct cyapa *cyapa = i2c_get_clientdata(client);
 	int error;
 
+	mutex_lock(&cyapa->input->mutex);
 	mutex_lock(&cyapa->state_sync_lock);
 
 	if (device_may_wakeup(dev) && cyapa->irq_wake) {
@@ -1422,6 +1431,7 @@
 	enable_irq(client->irq);
 
 	mutex_unlock(&cyapa->state_sync_lock);
+	mutex_unlock(&cyapa->input->mutex);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/cypress_ps2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/cypress_ps2.c
@@ -387,7 +387,9 @@
 	if (ret < 0)
 		return ret;
 
+#if ( CYPRESS_SIMULATED_MT != 1 )
 	__set_bit(INPUT_PROP_SEMI_MT, input->propbit);
+#endif
 
 	input_abs_set_res(input, ABS_X, cytp->tp_res_x);
 	input_abs_set_res(input, ABS_Y, cytp->tp_res_y);
@@ -473,6 +475,22 @@
 			((packet[5] & 0x0f) << 8) | packet[7];
 		if (cytp->mode & CYTP_BIT_ABS_PRESSURE)
 			report_data->contacts[1].z = report_data->contacts[0].z;
+#if ( CYPRESS_SIMULATED_MT == 1 )
+		/* simulate contact positions for >2 fingers */
+		if ( report_data->contact_cnt >= 3 ) {
+			int i;
+			for ( i=1; i<report_data->contact_cnt; i++ ) {
+			    report_data->contacts[i].x =
+					    report_data->contacts[0].x
+					    + 100*(i)*((i%2)?-1:1);
+			    report_data->contacts[i].y =
+					    report_data->contacts[0].y;
+			    if (cytp->mode & CYTP_BIT_ABS_PRESSURE)
+				    report_data->contacts[i].z =
+					    report_data->contacts[0].z;
+			}
+		}
+#endif
 	}
 
 	report_data->left = (header_byte & BTN_LEFT_BIT) ? 1 : 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/cypress_ps2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/cypress_ps2.h
@@ -131,7 +131,18 @@
 #define RESP_REMOTE_BIT     0x40
 #define RESP_SMBUS_BIT      0x80
 
-#define CYTP_MAX_MT_SLOTS 2
+/*
+ * CYPRESS_SIMULATED_MT
+ *   set to 1 for simulated multitouch (up to 5 contact points)
+ *   set to 0 for SEMI_MT (only 2 corner points, and count of fingers)
+ */
+#define CYPRESS_SIMULATED_MT 1
+
+#if ( CYPRESS_SIMULATED_MT == 1 )
+# define CYTP_MAX_MT_SLOTS 5
+#else
+# define CYTP_MAX_MT_SLOTS 2
+#endif
 
 struct cytp_contact {
 	int x;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/elan_i2c_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/elan_i2c_core.c
@@ -186,55 +186,21 @@
 	return 0;
 }
 
-static int elan_enable_power(struct elan_tp_data *data)
+static int elan_set_power(struct elan_tp_data *data, bool on)
 {
 	int repeat = ETP_RETRY_COUNT;
 	int error;
 
-	error = regulator_enable(data->vcc);
-	if (error) {
-		dev_err(&data->client->dev,
-			"failed to enable regulator: %d\n", error);
-		return error;
-	}
-
 	do {
-		error = data->ops->power_control(data->client, true);
+		error = data->ops->power_control(data->client, on);
 		if (error >= 0)
 			return 0;
 
 		msleep(30);
 	} while (--repeat > 0);
 
-	dev_err(&data->client->dev, "failed to enable power: %d\n", error);
-	return error;
-}
-
-static int elan_disable_power(struct elan_tp_data *data)
-{
-	int repeat = ETP_RETRY_COUNT;
-	int error;
-
-	do {
-		error = data->ops->power_control(data->client, false);
-		if (!error) {
-			error = regulator_disable(data->vcc);
-			if (error) {
-				dev_err(&data->client->dev,
-					"failed to disable regulator: %d\n",
-					error);
-				/* Attempt to power the chip back up */
-				data->ops->power_control(data->client, true);
-				break;
-			}
-
-			return 0;
-		}
-
-		msleep(30);
-	} while (--repeat > 0);
-
-	dev_err(&data->client->dev, "failed to disable power: %d\n", error);
+	dev_err(&data->client->dev, "failed to set power %s: %d\n",
+		on ? "on" : "off", error);
 	return error;
 }
 
@@ -1399,9 +1365,21 @@
 		/* Enable wake from IRQ */
 		data->irq_wake = (enable_irq_wake(client->irq) == 0);
 	} else {
-		ret = elan_disable_power(data);
+		ret = elan_set_power(data, false);
+		if (ret)
+			goto err;
+
+		ret = regulator_disable(data->vcc);
+		if (ret) {
+			dev_err(dev, "error %d disabling regulator\n", ret);
+			/* Attempt to power the chip back up */
+			elan_set_power(data, true);
+		}
 	}
 
+err:
+	if (ret)
+		enable_irq(client->irq);
 	mutex_unlock(&data->sysfs_mutex);
 	return ret;
 }
@@ -1412,12 +1390,18 @@
 	struct elan_tp_data *data = i2c_get_clientdata(client);
 	int error;
 
-	if (device_may_wakeup(dev) && data->irq_wake) {
+	if (!device_may_wakeup(dev)) {
+		error = regulator_enable(data->vcc);
+		if (error) {
+			dev_err(dev, "error %d enabling regulator\n", error);
+			goto err;
+		}
+	} else if (data->irq_wake) {
 		disable_irq_wake(client->irq);
 		data->irq_wake = false;
 	}
 
-	error = elan_enable_power(data);
+	error = elan_set_power(data, true);
 	if (error) {
 		dev_err(dev, "power up when resuming failed: %d\n", error);
 		goto err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/elantech.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/elantech.c
@@ -517,6 +517,19 @@
 	case 0x16008020U:
 	case 0x26800010U:
 	case 0x36808000U:
+
+		/*
+		 * This firmware misreport coordinates for trackpoint
+		 * occasionally. Discard packets outside of [-127, 127] range
+		 * to prevent cursor jumps.
+		 */
+		if (packet[4] == 0x80 || packet[5] == 0x80 ||
+		    packet[1] >> 7 == packet[4] >> 7 ||
+		    packet[2] >> 7 == packet[5] >> 7) {
+			elantech_debug("discarding packet [%6ph]\n", packet);
+			break;
+
+		}
 		x = packet[4] - (int)((packet[1]^0x80) << 1);
 		y = (int)((packet[2]^0x80) << 1) - packet[5];
 
@@ -661,10 +674,11 @@
 	struct input_dev *dev = psmouse->dev;
 	struct elantech_data *etd = psmouse->private;
 	unsigned char *packet = psmouse->packet;
-	int id = ((packet[3] & 0xe0) >> 5) - 1;
+	int id;
 	int pres, traces;
 
-	if (id < 0)
+	id = ((packet[3] & 0xe0) >> 5) - 1;
+	if (id < 0 || id >= ETP_MAX_FINGERS)
 		return;
 
 	etd->mt[id].x = ((packet[1] & 0x0f) << 8) | packet[2];
@@ -694,7 +708,7 @@
 	int id, sid;
 
 	id = ((packet[0] & 0xe0) >> 5) - 1;
-	if (id < 0)
+	if (id < 0 || id >= ETP_MAX_FINGERS)
 		return;
 
 	sid = ((packet[3] & 0xe0) >> 5) - 1;
@@ -715,7 +729,7 @@
 	input_report_abs(dev, ABS_MT_POSITION_X, etd->mt[id].x);
 	input_report_abs(dev, ABS_MT_POSITION_Y, etd->mt[id].y);
 
-	if (sid >= 0) {
+	if (sid >= 0 && sid < ETP_MAX_FINGERS) {
 		etd->mt[sid].x += delta_x2 * weight;
 		etd->mt[sid].y -= delta_y2 * weight;
 		input_mt_slot(dev, sid);
@@ -1463,15 +1477,46 @@
 }
 
 /*
+ * Some hw_version 4 models fail to properly activate absolute mode on
+ * resume without going through disable/enable cycle.
+ */
+static const struct dmi_system_id elantech_needs_reenable[] = {
+#if defined(CONFIG_DMI) && defined(CONFIG_X86)
+	{
+		/* Lenovo N24 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "81AF"),
+		},
+	},
+#endif
+	{ }
+};
+
+/*
  * Put the touchpad back into absolute mode when reconnecting
  */
 static int elantech_reconnect(struct psmouse *psmouse)
 {
+	int err;
+
 	psmouse_reset(psmouse);
 
 	if (elantech_detect(psmouse, 0))
 		return -1;
 
+	if (dmi_check_system(elantech_needs_reenable)) {
+		err = ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_DISABLE);
+		if (err)
+			psmouse_warn(psmouse, "failed to deactivate mouse on %s: %d\n",
+				     psmouse->ps2dev.serio->phys, err);
+
+		err = ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_ENABLE);
+		if (err)
+			psmouse_warn(psmouse, "failed to reactivate mouse on %s: %d\n",
+				     psmouse->ps2dev.serio->phys, err);
+	}
+
 	if (elantech_set_absolute_mode(psmouse)) {
 		psmouse_err(psmouse,
 			    "failed to put touchpad back into absolute mode.\n");
@@ -1575,7 +1620,13 @@
  */
 static int elantech_change_report_id(struct psmouse *psmouse)
 {
-	unsigned char param[2] = { 0x10, 0x03 };
+	/*
+	 * NOTE: the code is expecting to receive param[] as an array of 3
+	 * items (see __ps2_command()), even if in this case only 2 are
+	 * actually needed. Make sure the array size is 3 to avoid potential
+	 * stack out-of-bound accesses.
+	 */
+	unsigned char param[3] = { 0x10, 0x03 };
 
 	if (elantech_write_reg_params(psmouse, 0x7, param) ||
 	    elantech_read_reg_params(psmouse, 0x7, param) ||
@@ -2094,6 +2145,7 @@
 	psmouse->protocol_handler = elantech_process_byte;
 	psmouse->disconnect = elantech_disconnect;
 	psmouse->reconnect = elantech_reconnect;
+	psmouse->fast_reconnect = NULL;
 	psmouse->pktsize = info->hw_version > 1 ? 6 : 4;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/focaltech.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/focaltech.c
@@ -202,8 +202,8 @@
 	state->pressed = packet[0] >> 7;
 	finger1 = ((packet[0] >> 4) & 0x7) - 1;
 	if (finger1 < FOC_MAX_FINGERS) {
-		state->fingers[finger1].x += (char)packet[1];
-		state->fingers[finger1].y += (char)packet[2];
+		state->fingers[finger1].x += (s8)packet[1];
+		state->fingers[finger1].y += (s8)packet[2];
 	} else {
 		psmouse_err(psmouse, "First finger in rel packet invalid: %d\n",
 			    finger1);
@@ -218,8 +218,8 @@
 	 */
 	finger2 = ((packet[3] >> 4) & 0x7) - 1;
 	if (finger2 < FOC_MAX_FINGERS) {
-		state->fingers[finger2].x += (char)packet[4];
-		state->fingers[finger2].y += (char)packet[5];
+		state->fingers[finger2].x += (s8)packet[4];
+		state->fingers[finger2].y += (s8)packet[5];
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/mouse/synaptics.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/mouse/synaptics.c
@@ -187,6 +187,7 @@
 	"LEN2054", /* E480 */
 	"LEN2055", /* E580 */
 	"LEN2068", /* T14 Gen 1 */
+	"SYN3015", /* HP EliteBook 840 G2 */
 	"SYN3052", /* HP EliteBook 840 G4 */
 	"SYN3221", /* HP 15-ay000 */
 	"SYN323d", /* HP Spectre X360 13-w013dx */
@@ -1622,6 +1623,7 @@
 	psmouse->set_rate = synaptics_set_rate;
 	psmouse->disconnect = synaptics_disconnect;
 	psmouse->reconnect = synaptics_reconnect;
+	psmouse->fast_reconnect = NULL;
 	psmouse->cleanup = synaptics_reset;
 	/* Synaptics can usually stay in sync without extra help */
 	psmouse->resync_time = 0;
@@ -1751,6 +1753,7 @@
 		psmouse_matches_pnp_id(psmouse, topbuttonpad_pnp_ids) &&
 		!SYN_CAP_EXT_BUTTONS_STICK(info->ext_cap_10);
 	const struct rmi_device_platform_data pdata = {
+		.reset_delay_ms = 30,
 		.sensor_pdata = {
 			.sensor_type = rmi_sensor_touchpad,
 			.axis_align.flip_y = true,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/rmi4/rmi_bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/rmi4/rmi_bus.c
@@ -276,11 +276,11 @@
 
 	device_del(&fn->dev);
 	of_node_put(fn->dev.of_node);
-	put_device(&fn->dev);
 
 	for (i = 0; i < fn->num_of_irqs; i++)
 		irq_dispose_mapping(fn->irq[i]);
 
+	put_device(&fn->dev);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/rmi4/rmi_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/rmi4/rmi_driver.c
@@ -978,12 +978,12 @@
 
 	rmi_disable_irq(rmi_dev, false);
 
-	irq_domain_remove(data->irqdomain);
-	data->irqdomain = NULL;
-
 	rmi_f34_remove_sysfs(rmi_dev);
 	rmi_free_function_list(rmi_dev);
 
+	irq_domain_remove(data->irqdomain);
+	data->irqdomain = NULL;
+
 	return 0;
 }
 
@@ -1196,7 +1196,11 @@
 		}
 		rmi_driver_set_input_params(rmi_dev, data->input);
 		data->input->phys = devm_kasprintf(dev, GFP_KERNEL,
-						"%s/input0", dev_name(dev));
+						   "%s/input0", dev_name(dev));
+		if (!data->input->phys) {
+			retval = -ENOMEM;
+			goto err;
+		}
 	}
 
 	retval = rmi_init_functions(data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/rmi4/rmi_smbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/rmi4/rmi_smbus.c
@@ -235,12 +235,29 @@
 
 static int rmi_smb_enable_smbus_mode(struct rmi_smb_xport *rmi_smb)
 {
-	int retval;
+	struct i2c_client *client = rmi_smb->client;
+	int smbus_version;
+
+	/*
+	 * psmouse driver resets the controller, we only need to wait
+	 * to give the firmware chance to fully reinitialize.
+	 */
+	if (rmi_smb->xport.pdata.reset_delay_ms)
+		msleep(rmi_smb->xport.pdata.reset_delay_ms);
 
 	/* we need to get the smbus version to activate the touchpad */
-	retval = rmi_smb_get_version(rmi_smb);
-	if (retval < 0)
-		return retval;
+	smbus_version = rmi_smb_get_version(rmi_smb);
+	if (smbus_version < 0)
+		return smbus_version;
+
+	rmi_dbg(RMI_DEBUG_XPORT, &client->dev, "Smbus version is %d",
+		smbus_version);
+
+	if (smbus_version != 2 && smbus_version != 3) {
+		dev_err(&client->dev, "Unrecognized SMB version %d\n",
+				smbus_version);
+		return -ENODEV;
+	}
 
 	return 0;
 }
@@ -253,11 +270,10 @@
 	rmi_smb_clear_state(rmi_smb);
 
 	/*
-	 * we do not call the actual reset command, it has to be handled in
-	 * PS/2 or there will be races between PS/2 and SMBus.
-	 * PS/2 should ensure that a psmouse_reset is called before
-	 * intializing the device and after it has been removed to be in a known
-	 * state.
+	 * We do not call the actual reset command, it has to be handled in
+	 * PS/2 or there will be races between PS/2 and SMBus. PS/2 should
+	 * ensure that a psmouse_reset is called before initializing the
+	 * device and after it has been removed to be in a known state.
 	 */
 	return rmi_smb_enable_smbus_mode(rmi_smb);
 }
@@ -273,7 +289,6 @@
 {
 	struct rmi_device_platform_data *pdata = dev_get_platdata(&client->dev);
 	struct rmi_smb_xport *rmi_smb;
-	int smbus_version;
 	int error;
 
 	if (!pdata) {
@@ -312,18 +327,9 @@
 	rmi_smb->xport.proto_name = "smb";
 	rmi_smb->xport.ops = &rmi_smb_ops;
 
-	smbus_version = rmi_smb_get_version(rmi_smb);
-	if (smbus_version < 0)
-		return smbus_version;
-
-	rmi_dbg(RMI_DEBUG_XPORT, &client->dev, "Smbus version is %d",
-		smbus_version);
-
-	if (smbus_version != 2 && smbus_version != 3) {
-		dev_err(&client->dev, "Unrecognized SMB version %d\n",
-				smbus_version);
-		return -ENODEV;
-	}
+	error = rmi_smb_enable_smbus_mode(rmi_smb);
+	if (error)
+		return error;
 
 	i2c_set_clientdata(client, rmi_smb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/serio/gscps2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/serio/gscps2.c
@@ -350,6 +350,10 @@
 	ps2port->port = serio;
 	ps2port->padev = dev;
 	ps2port->addr = ioremap(hpa, GSC_STATUS + 4);
+	if (!ps2port->addr) {
+		ret = -ENOMEM;
+		goto fail_nomem;
+	}
 	spin_lock_init(&ps2port->lock);
 
 	gscps2_reset(ps2port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/serio/i8042-acpipnpio.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/serio/i8042-acpipnpio.h
@@ -0,0 +1,1747 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef _I8042_ACPIPNPIO_H
+#define _I8042_ACPIPNPIO_H
+
+
+#ifdef CONFIG_X86
+#include <asm/x86_init.h>
+#endif
+
+/*
+ * Names.
+ */
+
+#define I8042_KBD_PHYS_DESC "isa0060/serio0"
+#define I8042_AUX_PHYS_DESC "isa0060/serio1"
+#define I8042_MUX_PHYS_DESC "isa0060/serio%d"
+
+/*
+ * IRQs.
+ */
+
+#if defined(__ia64__)
+# define I8042_MAP_IRQ(x)	isa_irq_to_vector((x))
+#else
+# define I8042_MAP_IRQ(x)	(x)
+#endif
+
+#define I8042_KBD_IRQ	i8042_kbd_irq
+#define I8042_AUX_IRQ	i8042_aux_irq
+
+static int i8042_kbd_irq;
+static int i8042_aux_irq;
+
+/*
+ * Register numbers.
+ */
+
+#define I8042_COMMAND_REG	i8042_command_reg
+#define I8042_STATUS_REG	i8042_command_reg
+#define I8042_DATA_REG		i8042_data_reg
+
+static int i8042_command_reg = 0x64;
+static int i8042_data_reg = 0x60;
+
+
+static inline int i8042_read_data(void)
+{
+	return inb(I8042_DATA_REG);
+}
+
+static inline int i8042_read_status(void)
+{
+	return inb(I8042_STATUS_REG);
+}
+
+static inline void i8042_write_data(int val)
+{
+	outb(val, I8042_DATA_REG);
+}
+
+static inline void i8042_write_command(int val)
+{
+	outb(val, I8042_COMMAND_REG);
+}
+
+#ifdef CONFIG_X86
+
+#include <linux/dmi.h>
+
+#define SERIO_QUIRK_NOKBD		BIT(0)
+#define SERIO_QUIRK_NOAUX		BIT(1)
+#define SERIO_QUIRK_NOMUX		BIT(2)
+#define SERIO_QUIRK_FORCEMUX		BIT(3)
+#define SERIO_QUIRK_UNLOCK		BIT(4)
+#define SERIO_QUIRK_PROBE_DEFER		BIT(5)
+#define SERIO_QUIRK_RESET_ALWAYS	BIT(6)
+#define SERIO_QUIRK_RESET_NEVER		BIT(7)
+#define SERIO_QUIRK_DIRECT		BIT(8)
+#define SERIO_QUIRK_DUMBKBD		BIT(9)
+#define SERIO_QUIRK_NOLOOP		BIT(10)
+#define SERIO_QUIRK_NOTIMEOUT		BIT(11)
+#define SERIO_QUIRK_KBDRESET		BIT(12)
+#define SERIO_QUIRK_DRITEK		BIT(13)
+#define SERIO_QUIRK_NOPNP		BIT(14)
+
+/* Quirk table for different mainboards. Options similar or identical to i8042
+ * module parameters.
+ * ORDERING IS IMPORTANT! The first match will be apllied and the rest ignored.
+ * This allows entries to overwrite vendor wide quirks on a per device basis.
+ * Where this is irrelevant, entries are sorted case sensitive by DMI_SYS_VENDOR
+ * and/or DMI_BOARD_VENDOR to make it easier to avoid dublicate entries.
+ */
+static const struct dmi_system_id i8042_dmi_quirk_table[] __initconst = {
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ALIENWARE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Sentia"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X750LN"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Asus X450LCP */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X450LCP"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_NEVER)
+	},
+	{
+		/* ASUS ZenBook UX425UA/QA */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "ZenBook UX425"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_PROBE_DEFER | SERIO_QUIRK_RESET_NEVER)
+	},
+	{
+		/* ASUS ZenBook UM325UA/QA */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "ZenBook UX325"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_PROBE_DEFER | SERIO_QUIRK_RESET_NEVER)
+	},
+	/*
+	 * On some Asus laptops, just running self tests cause problems.
+	 */
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_CHASSIS_TYPE, "10"), /* Notebook */
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_NEVER)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_CHASSIS_TYPE, "31"), /* Convertible Notebook */
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_NEVER)
+	},
+	{
+		/* ASUS P65UP5 - AUX LOOP command does not raise AUX IRQ */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer INC."),
+			DMI_MATCH(DMI_BOARD_NAME, "P/I-P65UP5"),
+			DMI_MATCH(DMI_BOARD_VERSION, "REV 2.X"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* ASUS G1S */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer Inc."),
+			DMI_MATCH(DMI_BOARD_NAME, "G1S"),
+			DMI_MATCH(DMI_BOARD_VERSION, "1.0"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 1360"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Acer Aspire 5710 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5710"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Acer Aspire 7738 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 7738"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Acer Aspire 5536 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5536"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "0100"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/*
+		 * Acer Aspire 5738z
+		 * Touchpad stops working in mux mode when dis- + re-enabled
+		 * with the touchpad enable/disable toggle hotkey
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5738"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Acer Aspire One 150 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "AOA150"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire A114-31"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire A314-31"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire A315-31"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire ES1-132"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire ES1-332"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire ES1-432"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate Spin B118-RN"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	/*
+	 * Some Wistron based laptops need us to explicitly enable the 'Dritek
+	 * keyboard extension' to make their extra keys start generating scancodes.
+	 * Originally, this was just confined to older laptops, but a few Acer laptops
+	 * have turned up in 2007 that also need this again.
+	 */
+	{
+		/* Acer Aspire 5100 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5100"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer Aspire 5610 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5610"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer Aspire 5630 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5630"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer Aspire 5650 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5650"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer Aspire 5680 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5680"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer Aspire 5720 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5720"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer Aspire 9110 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 9110"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer TravelMate 660 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate 660"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer TravelMate 2490 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate 2490"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer TravelMate 4280 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate 4280"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DRITEK)
+	},
+	{
+		/* Acer TravelMate P459-G2-M */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate P459-G2-M"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Amoi M636/A737 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Amoi Electronics CO.,LTD."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "M636/A737 platform"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ByteSpeed LLC"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "ByteSpeed Laptop C15B"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Compal HEL80I */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "COMPAL"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HEL80I"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Compaq"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "ProLiant"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "8500"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Compaq"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "ProLiant"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "DL760"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Advent 4211 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "DIXONSXP"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Advent 4211"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Dell Embedded Box PC 3000 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Embedded Box PC 3000"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Dell XPS M1530 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "XPS M1530"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Dell Vostro 1510 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Vostro1510"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Dell Vostro V13 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Vostro V13"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* Dell Vostro 1320 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Vostro 1320"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Dell Vostro 1520 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Vostro 1520"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Dell Vostro 1720 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Vostro 1720"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Entroware Proteus */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Entroware"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Proteus"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "EL07R4"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS)
+	},
+	/*
+	 * Some Fujitsu notebooks are having trouble with touchpads if
+	 * active multiplexing mode is activated. Luckily they don't have
+	 * external PS/2 ports so we can safely disable it.
+	 * ... apparently some Toshibas don't like MUX mode either and
+	 * die horrible death on reboot.
+	 */
+	{
+		/* Fujitsu Lifebook P7010/P7010D */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "P7010"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook P5020D */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LifeBook P Series"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook S2000 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LifeBook S Series"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook S6230 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LifeBook S6230"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook T725 laptop */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK T725"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* Fujitsu Lifebook U745 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK U745"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu T70H */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "FMVLT70H"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu A544 laptop */
+		/* https://bugzilla.redhat.com/show_bug.cgi?id=1111138 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK A544"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* Fujitsu AH544 laptop */
+		/* https://bugzilla.kernel.org/show_bug.cgi?id=69731 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK AH544"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* Fujitsu U574 laptop */
+		/* https://bugzilla.kernel.org/show_bug.cgi?id=69731 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK U574"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* Fujitsu UH554 laptop */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK UH544"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* Fujitsu Lifebook P7010 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "0000000000"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu-Siemens Lifebook T3010 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK T3010"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu-Siemens Lifebook E4010 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E4010"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu-Siemens Amilo Pro 2010 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "AMILO Pro V2010"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu-Siemens Amilo Pro 2030 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "AMILO PRO V2030"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook A574/H */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "FMVA0501PZ"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook E756 */
+		/* https://bugzilla.suse.com/show_bug.cgi?id=1229056 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E756"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Fujitsu Lifebook E5411 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU CLIENT COMPUTING LIMITED"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E5411"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOAUX)
+	},
+	{
+		/* Fujitsu Lifebook U728 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK U728"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOAUX)
+	},
+	{
+		/* Gigabyte M912 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "M912"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "01"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Gigabyte Spring Peak - defines wrong chassis type */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Spring Peak"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Gigabyte T1005 - defines wrong chassis type ("Other") */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "T1005"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Gigabyte T1005M/P - defines wrong chassis type ("Other") */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "T1005M/P"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	/*
+	 * Some laptops need keyboard reset before probing for the trackpad to get
+	 * it detected, initialised & finally work.
+	 */
+	{
+		/* Gigabyte P35 v2 - Elantech touchpad */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "P35V2"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_KBDRESET)
+	},
+		{
+		/* Aorus branded Gigabyte X3 Plus - Elantech touchpad */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X3"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_KBDRESET)
+	},
+	{
+		/* Gigabyte P34 - Elantech touchpad */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "P34"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_KBDRESET)
+	},
+	{
+		/* Gigabyte P57 - Elantech touchpad */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "P57"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_KBDRESET)
+	},
+	{
+		/* Gericom Bellagio */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Gericom"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "N34AS6"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Gigabyte M1022M netbook */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co.,Ltd."),
+			DMI_MATCH(DMI_BOARD_NAME, "M1022E"),
+			DMI_MATCH(DMI_BOARD_VERSION, "1.02"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion dv9700"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "Rev 1"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/*
+		 * HP Pavilion DV4017EA -
+		 * errors on MUX ports are reported without raising AUXDATA
+		 * causing "spurious NAK" messages.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Pavilion dv4000 (EA032EA#ABF)"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/*
+		 * HP Pavilion ZT1000 -
+		 * like DV4017EA does not raise AUXERR for errors on MUX ports.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion Notebook PC"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "HP Pavilion Notebook ZT1000"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/*
+		 * HP Pavilion DV4270ca -
+		 * like DV4017EA does not raise AUXERR for errors on MUX ports.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Pavilion dv4000 (EH476UA#ABL)"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Newer HP Pavilion dv4 models */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion dv4 Notebook PC"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_NOTIMEOUT)
+	},
+	{
+		/* IBM 2656 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "IBM"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "2656"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Avatar AVIU-145A6 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Intel"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "IC4I"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Intel MBO Desktop D845PESV */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "D845PESV"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * Intel NUC D54250WYK - does not have i8042 controller but
+		 * declares PS/2 devices in DSDT.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "D54250WYK"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOPNP)
+	},
+	{
+		/* Lenovo 3000 n100 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "076804U"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Lenovo XiaoXin Air 12 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "80UN"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Lenovo LaVie Z */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo LaVie Z"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Lenovo Ideapad U455 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "20046"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Lenovo ThinkPad L460 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad L460"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Lenovo ThinkPad Twist S230u */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "33474HU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* LG Electronics X110 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LG Electronics Inc."),
+			DMI_MATCH(DMI_BOARD_NAME, "X110"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Medion Akoya Mini E1210 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "MEDION"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "E1210"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* Medion Akoya E1222 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "MEDION"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "E122X"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	{
+		/* MSI Wind U-100 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "MICRO-STAR INTERNATIONAL CO., LTD"),
+			DMI_MATCH(DMI_BOARD_NAME, "U-100"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * No data is coming from the touchscreen unless KBC
+		 * is in legacy mode.
+		 */
+		/* Panasonic CF-29 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Matsushita"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "CF-29"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Medion Akoya E7225 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Medion"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Akoya E7225"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "1.0"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Microsoft Virtual Machine */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Virtual Machine"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "VS2005R2"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Medion MAM 2070 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Notebook"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MAM 2070"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "5a"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* TUXEDO BU1406 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Notebook"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "N24_25BU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* OQO Model 01 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "OQO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "ZEPTO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "00"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "PEGATRON CORPORATION"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "C15B"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Acer Aspire 5 A515 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "PK"),
+			DMI_MATCH(DMI_BOARD_NAME, "Grumpy_PK"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOPNP)
+	},
+	{
+		/* ULI EV4873 - AUX LOOP does not work properly */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ULI"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "EV4873"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "5a"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/*
+		 * Arima-Rioworks HDAMB -
+		 * AUX LOOP command does not raise AUX IRQ
+		 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "RIOWORKS"),
+			DMI_MATCH(DMI_BOARD_NAME, "HDAMB"),
+			DMI_MATCH(DMI_BOARD_VERSION, "Rev E"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	{
+		/* Sharp Actius MM20 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "SHARP"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PC-MM20 Series"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/*
+		 * Sony Vaio FZ-240E -
+		 * reset and GET ID commands issued via KBD port are
+		 * sometimes being delivered to AUX3.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FZ240E"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/*
+		 * Most (all?) VAIOs do not have external PS/2 ports nor
+		 * they implement active multiplexing properly, and
+		 * MUX discovery usually messes up keyboard/touchpad.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "VAIO"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/* Sony Vaio FS-115b */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FS115B"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		/*
+		 * Sony Vaio VGN-CS series require MUX or the touch sensor
+		 * buttons will disturb touchpad operation
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "VGN-CS"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_FORCEMUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Satellite P10"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "EQUIUM A110"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE C850D"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX)
+	},
+	/*
+	 * A lot of modern Clevo barebones have touchpad and/or keyboard issues
+	 * after suspend fixable with nomux + reset + noloop + nopnp. Luckily,
+	 * none of them have an external PS/2 port so this can safely be set for
+	 * all of them. These two are based on a Clevo design, but have the
+	 * board_name changed.
+	 */
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "TUXEDO"),
+			DMI_MATCH(DMI_BOARD_NAME, "AURA1501"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "TUXEDO"),
+			DMI_MATCH(DMI_BOARD_NAME, "EDUBOOK1502"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/* Mivvy M310 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "VIOOO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "N10"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_RESET_ALWAYS)
+	},
+	/*
+	 * Some laptops need keyboard reset before probing for the trackpad to get
+	 * it detected, initialised & finally work.
+	 */
+	{
+		/* Schenker XMG C504 - Elantech touchpad */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "XMG"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "C504"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_KBDRESET)
+	},
+	{
+		/* Blue FB5601 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "blue"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "FB5601"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "M606"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOLOOP)
+	},
+	/*
+	 * Some TongFang barebones have touchpad and/or keyboard issues after
+	 * suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of
+	 * them have an external PS/2 port so this can safely be set for all of
+	 * them.
+	 * TongFang barebones come with board_vendor and/or system_vendor set to
+	 * a different value for each individual reseller. The only somewhat
+	 * universal way to identify them is by board_name.
+	 */
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GM6XGxX"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxXGxx"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxXGxX"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "GMxHGxx"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	/*
+	 * A lot of modern Clevo barebones have touchpad and/or keyboard issues
+	 * after suspend fixable with nomux + reset + noloop + nopnp. Luckily,
+	 * none of them have an external PS/2 port so this can safely be set for
+	 * all of them.
+	 * Clevo barebones come with board_vendor and/or system_vendor set to
+	 * either the very generic string "Notebook" and/or a different value
+	 * for each individual reseller. The only somewhat universal way to
+	 * identify them is by board_name.
+	 */
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "LAPQC71A"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "LAPQC71B"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "N140CU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "N141CU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "NH5xAx"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "NL5xRU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	/*
+	 * At least one modern Clevo barebone has the touchpad connected both
+	 * via PS/2 and i2c interface. This causes a race condition between the
+	 * psmouse and i2c-hid driver. Since the full capability of the touchpad
+	 * is available via the i2c interface and the device has no external
+	 * PS/2 port, it is safe to just ignore all ps2 mouses here to avoid
+	 * this issue. The known affected device is the
+	 * TUXEDO InfinityBook S17 Gen6 / Clevo NS70MU which comes with one of
+	 * the two different dmi strings below. NS50MU is not a typo!
+	 */
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "NS50MU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOAUX | SERIO_QUIRK_NOMUX |
+					SERIO_QUIRK_RESET_ALWAYS | SERIO_QUIRK_NOLOOP |
+					SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "NS50_70MU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOAUX | SERIO_QUIRK_NOMUX |
+					SERIO_QUIRK_RESET_ALWAYS | SERIO_QUIRK_NOLOOP |
+					SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "NS5x_7xPU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOAUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "NJ50_70CU"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * This is only a partial board_name and might be followed by
+		 * another letter or number. DMI_MATCH however does do partial
+		 * matching.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "P65xH"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/* Clevo P650RS, 650RP6, Sager NP8152-S, and others */
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "P65xRP"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * This is only a partial board_name and might be followed by
+		 * another letter or number. DMI_MATCH however does do partial
+		 * matching.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "P65_P67H"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * This is only a partial board_name and might be followed by
+		 * another letter or number. DMI_MATCH however does do partial
+		 * matching.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "P65_67RP"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * This is only a partial board_name and might be followed by
+		 * another letter or number. DMI_MATCH however does do partial
+		 * matching.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "P65_67RS"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * This is only a partial board_name and might be followed by
+		 * another letter or number. DMI_MATCH however does do partial
+		 * matching.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "P67xRP"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "PB50_70DFx,DDx"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "PCX0DX"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	/* See comment on TUXEDO InfinityBook S17 Gen6 / Clevo NS70MU above */
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "PD5x_7xPNP_PNR_PNN_PNT"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOAUX)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "X170SM"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "X170KM-G"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_NOMUX | SERIO_QUIRK_RESET_ALWAYS |
+					SERIO_QUIRK_NOLOOP | SERIO_QUIRK_NOPNP)
+	},
+	{
+		/*
+		 * The Ayaneo Kun is a handheld device where some the buttons
+		 * are handled by an AT keyboard. The keyboard is usually
+		 * detected as raw, but sometimes, usually after a cold boot,
+		 * it is detected as translated. Make sure that the keyboard
+		 * is always in raw mode.
+		 */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "AYANEO"),
+			DMI_MATCH(DMI_BOARD_NAME, "KUN"),
+		},
+		.driver_data = (void *)(SERIO_QUIRK_DIRECT)
+	},
+	{ }
+};
+
+#ifdef CONFIG_PNP
+static const struct dmi_system_id i8042_dmi_laptop_table[] __initconst = {
+	{
+		.matches = {
+			DMI_MATCH(DMI_CHASSIS_TYPE, "8"), /* Portable */
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_CHASSIS_TYPE, "9"), /* Laptop */
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_CHASSIS_TYPE, "10"), /* Notebook */
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_CHASSIS_TYPE, "14"), /* Sub-Notebook */
+		},
+	},
+	{ }
+};
+#endif
+
+#endif /* CONFIG_X86 */
+
+#ifdef CONFIG_PNP
+#include <linux/pnp.h>
+
+static bool i8042_pnp_kbd_registered;
+static unsigned int i8042_pnp_kbd_devices;
+static bool i8042_pnp_aux_registered;
+static unsigned int i8042_pnp_aux_devices;
+
+static int i8042_pnp_command_reg;
+static int i8042_pnp_data_reg;
+static int i8042_pnp_kbd_irq;
+static int i8042_pnp_aux_irq;
+
+static char i8042_pnp_kbd_name[32];
+static char i8042_pnp_aux_name[32];
+
+static void i8042_pnp_id_to_string(struct pnp_id *id, char *dst, int dst_size)
+{
+	strlcpy(dst, "PNP:", dst_size);
+
+	while (id) {
+		strlcat(dst, " ", dst_size);
+		strlcat(dst, id->id, dst_size);
+		id = id->next;
+	}
+}
+
+static int i8042_pnp_kbd_probe(struct pnp_dev *dev, const struct pnp_device_id *did)
+{
+	if (pnp_port_valid(dev, 0) && pnp_port_len(dev, 0) == 1)
+		i8042_pnp_data_reg = pnp_port_start(dev,0);
+
+	if (pnp_port_valid(dev, 1) && pnp_port_len(dev, 1) == 1)
+		i8042_pnp_command_reg = pnp_port_start(dev, 1);
+
+	if (pnp_irq_valid(dev,0))
+		i8042_pnp_kbd_irq = pnp_irq(dev, 0);
+
+	strlcpy(i8042_pnp_kbd_name, did->id, sizeof(i8042_pnp_kbd_name));
+	if (strlen(pnp_dev_name(dev))) {
+		strlcat(i8042_pnp_kbd_name, ":", sizeof(i8042_pnp_kbd_name));
+		strlcat(i8042_pnp_kbd_name, pnp_dev_name(dev), sizeof(i8042_pnp_kbd_name));
+	}
+	i8042_pnp_id_to_string(dev->id, i8042_kbd_firmware_id,
+			       sizeof(i8042_kbd_firmware_id));
+	i8042_kbd_fwnode = dev_fwnode(&dev->dev);
+
+	/* Keyboard ports are always supposed to be wakeup-enabled */
+	device_set_wakeup_enable(&dev->dev, true);
+
+	i8042_pnp_kbd_devices++;
+	return 0;
+}
+
+static int i8042_pnp_aux_probe(struct pnp_dev *dev, const struct pnp_device_id *did)
+{
+	if (pnp_port_valid(dev, 0) && pnp_port_len(dev, 0) == 1)
+		i8042_pnp_data_reg = pnp_port_start(dev,0);
+
+	if (pnp_port_valid(dev, 1) && pnp_port_len(dev, 1) == 1)
+		i8042_pnp_command_reg = pnp_port_start(dev, 1);
+
+	if (pnp_irq_valid(dev, 0))
+		i8042_pnp_aux_irq = pnp_irq(dev, 0);
+
+	strlcpy(i8042_pnp_aux_name, did->id, sizeof(i8042_pnp_aux_name));
+	if (strlen(pnp_dev_name(dev))) {
+		strlcat(i8042_pnp_aux_name, ":", sizeof(i8042_pnp_aux_name));
+		strlcat(i8042_pnp_aux_name, pnp_dev_name(dev), sizeof(i8042_pnp_aux_name));
+	}
+	i8042_pnp_id_to_string(dev->id, i8042_aux_firmware_id,
+			       sizeof(i8042_aux_firmware_id));
+
+	i8042_pnp_aux_devices++;
+	return 0;
+}
+
+static const struct pnp_device_id pnp_kbd_devids[] = {
+	{ .id = "PNP0300", .driver_data = 0 },
+	{ .id = "PNP0301", .driver_data = 0 },
+	{ .id = "PNP0302", .driver_data = 0 },
+	{ .id = "PNP0303", .driver_data = 0 },
+	{ .id = "PNP0304", .driver_data = 0 },
+	{ .id = "PNP0305", .driver_data = 0 },
+	{ .id = "PNP0306", .driver_data = 0 },
+	{ .id = "PNP0309", .driver_data = 0 },
+	{ .id = "PNP030a", .driver_data = 0 },
+	{ .id = "PNP030b", .driver_data = 0 },
+	{ .id = "PNP0320", .driver_data = 0 },
+	{ .id = "PNP0343", .driver_data = 0 },
+	{ .id = "PNP0344", .driver_data = 0 },
+	{ .id = "PNP0345", .driver_data = 0 },
+	{ .id = "CPQA0D7", .driver_data = 0 },
+	{ .id = "", },
+};
+MODULE_DEVICE_TABLE(pnp, pnp_kbd_devids);
+
+static struct pnp_driver i8042_pnp_kbd_driver = {
+	.name           = "i8042 kbd",
+	.id_table       = pnp_kbd_devids,
+	.probe          = i8042_pnp_kbd_probe,
+	.driver         = {
+		.probe_type = PROBE_FORCE_SYNCHRONOUS,
+		.suppress_bind_attrs = true,
+	},
+};
+
+static const struct pnp_device_id pnp_aux_devids[] = {
+	{ .id = "AUI0200", .driver_data = 0 },
+	{ .id = "FJC6000", .driver_data = 0 },
+	{ .id = "FJC6001", .driver_data = 0 },
+	{ .id = "PNP0f03", .driver_data = 0 },
+	{ .id = "PNP0f0b", .driver_data = 0 },
+	{ .id = "PNP0f0e", .driver_data = 0 },
+	{ .id = "PNP0f12", .driver_data = 0 },
+	{ .id = "PNP0f13", .driver_data = 0 },
+	{ .id = "PNP0f19", .driver_data = 0 },
+	{ .id = "PNP0f1c", .driver_data = 0 },
+	{ .id = "SYN0801", .driver_data = 0 },
+	{ .id = "", },
+};
+MODULE_DEVICE_TABLE(pnp, pnp_aux_devids);
+
+static struct pnp_driver i8042_pnp_aux_driver = {
+	.name           = "i8042 aux",
+	.id_table       = pnp_aux_devids,
+	.probe          = i8042_pnp_aux_probe,
+	.driver         = {
+		.probe_type = PROBE_FORCE_SYNCHRONOUS,
+		.suppress_bind_attrs = true,
+	},
+};
+
+static void i8042_pnp_exit(void)
+{
+	if (i8042_pnp_kbd_registered) {
+		i8042_pnp_kbd_registered = false;
+		pnp_unregister_driver(&i8042_pnp_kbd_driver);
+	}
+
+	if (i8042_pnp_aux_registered) {
+		i8042_pnp_aux_registered = false;
+		pnp_unregister_driver(&i8042_pnp_aux_driver);
+	}
+}
+
+static int __init i8042_pnp_init(void)
+{
+	char kbd_irq_str[4] = { 0 }, aux_irq_str[4] = { 0 };
+	bool pnp_data_busted = false;
+	int err;
+
+	if (i8042_nopnp) {
+		pr_info("PNP detection disabled\n");
+		return 0;
+	}
+
+	err = pnp_register_driver(&i8042_pnp_kbd_driver);
+	if (!err)
+		i8042_pnp_kbd_registered = true;
+
+	err = pnp_register_driver(&i8042_pnp_aux_driver);
+	if (!err)
+		i8042_pnp_aux_registered = true;
+
+	if (!i8042_pnp_kbd_devices && !i8042_pnp_aux_devices) {
+		i8042_pnp_exit();
+#if defined(__ia64__)
+		return -ENODEV;
+#else
+		pr_info("PNP: No PS/2 controller found.\n");
+		if (x86_platform.legacy.i8042 !=
+				X86_LEGACY_I8042_EXPECTED_PRESENT)
+			return -ENODEV;
+		pr_info("Probing ports directly.\n");
+		return 0;
+#endif
+	}
+
+	if (i8042_pnp_kbd_devices)
+		snprintf(kbd_irq_str, sizeof(kbd_irq_str),
+			"%d", i8042_pnp_kbd_irq);
+	if (i8042_pnp_aux_devices)
+		snprintf(aux_irq_str, sizeof(aux_irq_str),
+			"%d", i8042_pnp_aux_irq);
+
+	pr_info("PNP: PS/2 Controller [%s%s%s] at %#x,%#x irq %s%s%s\n",
+		i8042_pnp_kbd_name, (i8042_pnp_kbd_devices && i8042_pnp_aux_devices) ? "," : "",
+		i8042_pnp_aux_name,
+		i8042_pnp_data_reg, i8042_pnp_command_reg,
+		kbd_irq_str, (i8042_pnp_kbd_devices && i8042_pnp_aux_devices) ? "," : "",
+		aux_irq_str);
+
+#if defined(__ia64__)
+	if (!i8042_pnp_kbd_devices)
+		i8042_nokbd = true;
+	if (!i8042_pnp_aux_devices)
+		i8042_noaux = true;
+#endif
+
+	if (((i8042_pnp_data_reg & ~0xf) == (i8042_data_reg & ~0xf) &&
+	      i8042_pnp_data_reg != i8042_data_reg) ||
+	    !i8042_pnp_data_reg) {
+		pr_warn("PNP: PS/2 controller has invalid data port %#x; using default %#x\n",
+			i8042_pnp_data_reg, i8042_data_reg);
+		i8042_pnp_data_reg = i8042_data_reg;
+		pnp_data_busted = true;
+	}
+
+	if (((i8042_pnp_command_reg & ~0xf) == (i8042_command_reg & ~0xf) &&
+	      i8042_pnp_command_reg != i8042_command_reg) ||
+	    !i8042_pnp_command_reg) {
+		pr_warn("PNP: PS/2 controller has invalid command port %#x; using default %#x\n",
+			i8042_pnp_command_reg, i8042_command_reg);
+		i8042_pnp_command_reg = i8042_command_reg;
+		pnp_data_busted = true;
+	}
+
+	if (!i8042_nokbd && !i8042_pnp_kbd_irq) {
+		pr_warn("PNP: PS/2 controller doesn't have KBD irq; using default %d\n",
+			i8042_kbd_irq);
+		i8042_pnp_kbd_irq = i8042_kbd_irq;
+		pnp_data_busted = true;
+	}
+
+	if (!i8042_noaux && !i8042_pnp_aux_irq) {
+		if (!pnp_data_busted && i8042_pnp_kbd_irq) {
+			pr_warn("PNP: PS/2 appears to have AUX port disabled, "
+				"if this is incorrect please boot with i8042.nopnp\n");
+			i8042_noaux = true;
+		} else {
+			pr_warn("PNP: PS/2 controller doesn't have AUX irq; using default %d\n",
+				i8042_aux_irq);
+			i8042_pnp_aux_irq = i8042_aux_irq;
+		}
+	}
+
+	i8042_data_reg = i8042_pnp_data_reg;
+	i8042_command_reg = i8042_pnp_command_reg;
+	i8042_kbd_irq = i8042_pnp_kbd_irq;
+	i8042_aux_irq = i8042_pnp_aux_irq;
+
+#ifdef CONFIG_X86
+	i8042_bypass_aux_irq_test = !pnp_data_busted &&
+				    dmi_check_system(i8042_dmi_laptop_table);
+#endif
+
+	return 0;
+}
+
+#else  /* !CONFIG_PNP */
+static inline int i8042_pnp_init(void) { return 0; }
+static inline void i8042_pnp_exit(void) { }
+#endif /* CONFIG_PNP */
+
+
+#ifdef CONFIG_X86
+static void __init i8042_check_quirks(void)
+{
+	const struct dmi_system_id *device_quirk_info;
+	uintptr_t quirks;
+
+	device_quirk_info = dmi_first_match(i8042_dmi_quirk_table);
+	if (!device_quirk_info)
+		return;
+
+	quirks = (uintptr_t)device_quirk_info->driver_data;
+
+	if (quirks & SERIO_QUIRK_NOKBD)
+		i8042_nokbd = true;
+	if (quirks & SERIO_QUIRK_NOAUX)
+		i8042_noaux = true;
+	if (quirks & SERIO_QUIRK_NOMUX)
+		i8042_nomux = true;
+	if (quirks & SERIO_QUIRK_FORCEMUX)
+		i8042_nomux = false;
+	if (quirks & SERIO_QUIRK_UNLOCK)
+		i8042_unlock = true;
+	if (quirks & SERIO_QUIRK_PROBE_DEFER)
+		i8042_probe_defer = true;
+	/* Honor module parameter when value is not default */
+	if (i8042_reset == I8042_RESET_DEFAULT) {
+		if (quirks & SERIO_QUIRK_RESET_ALWAYS)
+			i8042_reset = I8042_RESET_ALWAYS;
+		if (quirks & SERIO_QUIRK_RESET_NEVER)
+			i8042_reset = I8042_RESET_NEVER;
+	}
+	if (quirks & SERIO_QUIRK_DIRECT)
+		i8042_direct = true;
+	if (quirks & SERIO_QUIRK_DUMBKBD)
+		i8042_dumbkbd = true;
+	if (quirks & SERIO_QUIRK_NOLOOP)
+		i8042_noloop = true;
+	if (quirks & SERIO_QUIRK_NOTIMEOUT)
+		i8042_notimeout = true;
+	if (quirks & SERIO_QUIRK_KBDRESET)
+		i8042_kbdreset = true;
+	if (quirks & SERIO_QUIRK_DRITEK)
+		i8042_dritek = true;
+#ifdef CONFIG_PNP
+	if (quirks & SERIO_QUIRK_NOPNP)
+		i8042_nopnp = true;
+#endif
+}
+#else
+static inline void i8042_check_quirks(void) {}
+#endif
+
+static int __init i8042_platform_init(void)
+{
+	int retval;
+
+#ifdef CONFIG_X86
+	u8 a20_on = 0xdf;
+	/* Just return if platform does not have i8042 controller */
+	if (x86_platform.legacy.i8042 == X86_LEGACY_I8042_PLATFORM_ABSENT)
+		return -ENODEV;
+#endif
+
+/*
+ * On ix86 platforms touching the i8042 data register region can do really
+ * bad things. Because of this the region is always reserved on ix86 boxes.
+ *
+ *	if (!request_region(I8042_DATA_REG, 16, "i8042"))
+ *		return -EBUSY;
+ */
+
+	i8042_kbd_irq = I8042_MAP_IRQ(1);
+	i8042_aux_irq = I8042_MAP_IRQ(12);
+
+#if defined(__ia64__)
+	i8042_reset = I8042_RESET_ALWAYS;
+#endif
+
+	i8042_check_quirks();
+
+	retval = i8042_pnp_init();
+	if (retval)
+		return retval;
+
+#ifdef CONFIG_X86
+	/*
+	 * A20 was already enabled during early kernel init. But some buggy
+	 * BIOSes (in MSI Laptops) require A20 to be enabled using 8042 to
+	 * resume from S3. So we do it here and hope that nothing breaks.
+	 */
+	i8042_command(&a20_on, 0x10d1);
+	i8042_command(NULL, 0x00ff);	/* Null command for SMM firmware */
+#endif /* CONFIG_X86 */
+
+	return retval;
+}
+
+static inline void i8042_platform_exit(void)
+{
+	i8042_pnp_exit();
+}
+
+#endif /* _I8042_ACPIPNPIO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/serio/i8042.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/serio/i8042.c
@@ -22,6 +22,7 @@
 #include <linux/slab.h>
 #include <linux/suspend.h>
 #include <linux/property.h>
+#include <linux/dmi.h>
 
 #include <asm/io.h>
 
@@ -45,6 +46,10 @@
 module_param_named(unlock, i8042_unlock, bool, 0);
 MODULE_PARM_DESC(unlock, "Ignore keyboard lock.");
 
+static bool i8042_probe_defer;
+module_param_named(probe_defer, i8042_probe_defer, bool, 0);
+MODULE_PARM_DESC(probe_defer, "Allow deferred probing.");
+
 enum i8042_controller_reset_mode {
 	I8042_RESET_NEVER,
 	I8042_RESET_ALWAYS,
@@ -174,6 +179,24 @@
 static bool (*i8042_platform_filter)(unsigned char data, unsigned char str,
 				     struct serio *serio);
 
+static int __init i8042_set_noaux(const struct dmi_system_id *dmi)
+{
+	i8042_noaux = true;
+	return 1;
+}
+
+static const struct dmi_system_id i8042_quirks[] __initconst = {
+	{
+		.callback = i8042_set_noaux,
+		.ident = "Dell laptop",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Precision 5550"),
+		},
+	},
+	{},
+};
+
 void i8042_lock_chip(void)
 {
 	mutex_lock(&i8042_mutex);
@@ -617,7 +640,7 @@
 	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
 		i8042_ctr &= ~I8042_CTR_KBDINT;
 		i8042_ctr |= I8042_CTR_KBDDIS;
-		pr_err("Failed to enable KBD port\n");
+		pr_info("Failed to enable KBD port\n");
 		return -EIO;
 	}
 
@@ -636,7 +659,7 @@
 	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
 		i8042_ctr &= ~I8042_CTR_AUXINT;
 		i8042_ctr |= I8042_CTR_AUXDIS;
-		pr_err("Failed to enable AUX port\n");
+		pr_info("Failed to enable AUX port\n");
 		return -EIO;
 	}
 
@@ -711,7 +734,7 @@
  * LCS/Telegraphics.
  */
 
-static int __init i8042_check_mux(void)
+static int i8042_check_mux(void)
 {
 	unsigned char mux_version;
 
@@ -728,7 +751,7 @@
 	i8042_ctr &= ~I8042_CTR_AUXINT;
 
 	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
-		pr_err("Failed to disable AUX port, can't use MUX\n");
+		pr_info("Failed to disable AUX port, can't use MUX\n");
 		return -EIO;
 	}
 
@@ -740,10 +763,10 @@
 /*
  * The following is used to test AUX IRQ delivery.
  */
-static struct completion i8042_aux_irq_delivered __initdata;
-static bool i8042_irq_being_tested __initdata;
+static struct completion i8042_aux_irq_delivered;
+static bool i8042_irq_being_tested;
 
-static irqreturn_t __init i8042_aux_test_irq(int irq, void *dev_id)
+static irqreturn_t i8042_aux_test_irq(int irq, void *dev_id)
 {
 	unsigned long flags;
 	unsigned char str, data;
@@ -770,7 +793,7 @@
  * verifies success by readinng CTR. Used when testing for presence of AUX
  * port.
  */
-static int __init i8042_toggle_aux(bool on)
+static int i8042_toggle_aux(bool on)
 {
 	unsigned char param;
 	int i;
@@ -798,7 +821,7 @@
  * the presence of an AUX interface.
  */
 
-static int __init i8042_check_aux(void)
+static int i8042_check_aux(void)
 {
 	int retval = -1;
 	bool irq_registered = false;
@@ -943,25 +966,28 @@
 {
 	unsigned char param;
 	int i = 0;
+	int ret;
 
 	/*
 	 * We try this 5 times; on some really fragile systems this does not
 	 * take the first time...
 	 */
-	do {
+	while (i++ < 5) {
 
-		if (i8042_command(&param, I8042_CMD_CTL_TEST)) {
-			pr_err("i8042 controller selftest timeout\n");
-			return -ENODEV;
-		}
-
-		if (param == I8042_RET_CTL_TEST)
+		ret = i8042_command(&param, I8042_CMD_CTL_TEST);
+		if (ret)
+			pr_info("i8042 controller selftest timeout (%d/5)\n", i);
+		else if (param == I8042_RET_CTL_TEST)
 			return 0;
+		else
+			dbg("i8042 controller selftest: %#x != %#x\n",
+			    param, I8042_RET_CTL_TEST);
 
-		dbg("i8042 controller selftest: %#x != %#x\n",
-		    param, I8042_RET_CTL_TEST);
 		msleep(50);
-	} while (i++ < 5);
+	}
+
+	if (ret)
+		return -ENODEV;
 
 #ifdef CONFIG_X86
 	/*
@@ -973,7 +999,7 @@
 	pr_info("giving up on controller selftest, continuing anyway...\n");
 	return 0;
 #else
-	pr_err("i8042 controller selftest failed\n");
+	pr_info("i8042 controller selftest failed\n");
 	return -EIO;
 #endif
 }
@@ -1005,7 +1031,7 @@
 
 		if (i8042_command(&ctr[n++ % 2], I8042_CMD_CTL_RCTR)) {
 			pr_err("Can't read CTR while initializing i8042\n");
-			return -EIO;
+			return i8042_probe_defer ? -EPROBE_DEFER : -EIO;
 		}
 
 	} while (n < 2 || ctr[0] != ctr[1]);
@@ -1320,7 +1346,7 @@
 	i8042_controller_reset(false);
 }
 
-static int __init i8042_create_kbd_port(void)
+static int i8042_create_kbd_port(void)
 {
 	struct serio *serio;
 	struct i8042_port *port = &i8042_ports[I8042_KBD_PORT_NO];
@@ -1349,7 +1375,7 @@
 	return 0;
 }
 
-static int __init i8042_create_aux_port(int idx)
+static int i8042_create_aux_port(int idx)
 {
 	struct serio *serio;
 	int port_no = idx < 0 ? I8042_AUX_PORT_NO : I8042_MUX_PORT_NO + idx;
@@ -1386,13 +1412,13 @@
 	return 0;
 }
 
-static void __init i8042_free_kbd_port(void)
+static void i8042_free_kbd_port(void)
 {
 	kfree(i8042_ports[I8042_KBD_PORT_NO].serio);
 	i8042_ports[I8042_KBD_PORT_NO].serio = NULL;
 }
 
-static void __init i8042_free_aux_ports(void)
+static void i8042_free_aux_ports(void)
 {
 	int i;
 
@@ -1402,7 +1428,7 @@
 	}
 }
 
-static void __init i8042_register_ports(void)
+static void i8042_register_ports(void)
 {
 	int i;
 
@@ -1443,7 +1469,7 @@
 	i8042_aux_irq_registered = i8042_kbd_irq_registered = false;
 }
 
-static int __init i8042_setup_aux(void)
+static int i8042_setup_aux(void)
 {
 	int (*aux_enable)(void);
 	int error;
@@ -1485,7 +1511,7 @@
 	return error;
 }
 
-static int __init i8042_setup_kbd(void)
+static int i8042_setup_kbd(void)
 {
 	int error;
 
@@ -1535,12 +1561,10 @@
 	return 0;
 }
 
-static int __init i8042_probe(struct platform_device *dev)
+static int i8042_probe(struct platform_device *dev)
 {
 	int error;
 
-	i8042_platform_device = dev;
-
 	if (i8042_reset == I8042_RESET_ALWAYS) {
 		error = i8042_controller_selftest();
 		if (error)
@@ -1556,6 +1580,8 @@
 		i8042_dritek_enable();
 #endif
 
+	dmi_check_system(i8042_quirks);
+
 	if (!i8042_noaux) {
 		error = i8042_setup_aux();
 		if (error && error != -ENODEV && error != -EBUSY)
@@ -1578,7 +1604,6 @@
 	i8042_free_aux_ports();	/* in case KBD failed but AUX not */
 	i8042_free_irqs();
 	i8042_controller_reset(false);
-	i8042_platform_device = NULL;
 
 	return error;
 }
@@ -1588,7 +1613,6 @@
 	i8042_unregister_ports();
 	i8042_free_irqs();
 	i8042_controller_reset(false);
-	i8042_platform_device = NULL;
 
 	return 0;
 }
@@ -1600,6 +1624,7 @@
 		.pm	= &i8042_pm_ops,
 #endif
 	},
+	.probe		= i8042_probe,
 	.remove		= i8042_remove,
 	.shutdown	= i8042_shutdown,
 };
@@ -1610,7 +1635,6 @@
 
 static int __init i8042_init(void)
 {
-	struct platform_device *pdev;
 	int err;
 
 	dbg_init();
@@ -1626,17 +1650,29 @@
 	/* Set this before creating the dev to allow i8042_command to work right away */
 	i8042_present = true;
 
-	pdev = platform_create_bundle(&i8042_driver, i8042_probe, NULL, 0, NULL, 0);
-	if (IS_ERR(pdev)) {
-		err = PTR_ERR(pdev);
+	err = platform_driver_register(&i8042_driver);
+	if (err)
 		goto err_platform_exit;
+
+	i8042_platform_device = platform_device_alloc("i8042", -1);
+	if (!i8042_platform_device) {
+		err = -ENOMEM;
+		goto err_unregister_driver;
 	}
 
+	err = platform_device_add(i8042_platform_device);
+	if (err)
+		goto err_free_device;
+
 	bus_register_notifier(&serio_bus, &i8042_kbd_bind_notifier_block);
 	panic_blink = i8042_panic_blink;
 
 	return 0;
 
+err_free_device:
+	platform_device_put(i8042_platform_device);
+err_unregister_driver:
+	platform_driver_unregister(&i8042_driver);
  err_platform_exit:
 	i8042_platform_exit();
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/serio/i8042.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/serio/i8042.h
@@ -20,7 +20,7 @@
 #elif defined(CONFIG_SPARC)
 #include "i8042-sparcio.h"
 #elif defined(CONFIG_X86) || defined(CONFIG_IA64)
-#include "i8042-x86ia64io.h"
+#include "i8042-acpipnpio.h"
 #else
 #include "i8042-io.h"
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/serio/ioc3kbd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/serio/ioc3kbd.c
@@ -190,7 +190,7 @@
 	return 0;
 }
 
-static int ioc3kbd_remove(struct platform_device *pdev)
+static void ioc3kbd_remove(struct platform_device *pdev)
 {
 	struct ioc3kbd_data *d = platform_get_drvdata(pdev);
 
@@ -198,13 +198,18 @@
 
 	serio_unregister_port(d->kbd);
 	serio_unregister_port(d->aux);
-
-	return 0;
 }
 
+static const struct platform_device_id ioc3kbd_id_table[] = {
+	{ "ioc3-kbd", },
+	{ }
+};
+MODULE_DEVICE_TABLE(platform, ioc3kbd_id_table);
+
 static struct platform_driver ioc3kbd_driver = {
 	.probe          = ioc3kbd_probe,
-	.remove         = ioc3kbd_remove,
+	.remove_new     = ioc3kbd_remove,
+	.id_table	= ioc3kbd_id_table,
 	.driver = {
 		.name = "ioc3-kbd",
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/tablet/aiptek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/tablet/aiptek.c
@@ -1787,15 +1787,13 @@
 	input_set_abs_params(inputdev, ABS_TILT_Y, AIPTEK_TILT_MIN, AIPTEK_TILT_MAX, 0, 0);
 	input_set_abs_params(inputdev, ABS_WHEEL, AIPTEK_WHEEL_MIN, AIPTEK_WHEEL_MAX - 1, 0, 0);
 
-	/* Verify that a device really has an endpoint */
-	if (intf->cur_altsetting->desc.bNumEndpoints < 1) {
+	err = usb_find_common_endpoints(intf->cur_altsetting,
+					NULL, NULL, &endpoint, NULL);
+	if (err) {
 		dev_err(&intf->dev,
-			"interface has %d endpoints, but must have minimum 1\n",
-			intf->cur_altsetting->desc.bNumEndpoints);
-		err = -EINVAL;
+			"interface has no int in endpoints, but must have minimum 1\n");
 		goto fail3;
 	}
-	endpoint = &intf->cur_altsetting->endpoint[0].desc;
 
 	/* Go set up our URB, which is called when the tablet receives
 	 * input.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/ads7846.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/ads7846.c
@@ -818,7 +818,7 @@
 		m = &ts->msg[msg_idx];
 		error = spi_sync(ts->spi, m);
 		if (error) {
-			dev_err(&ts->spi->dev, "spi_sync --> %d\n", error);
+			dev_err_ratelimited(&ts->spi->dev, "spi_sync --> %d\n", error);
 			packet->ignore = true;
 			return;
 		}
@@ -851,14 +851,8 @@
 	if (x == MAX_12BIT)
 		x = 0;
 
-	if (ts->model == 7843) {
+	if (ts->model == 7843 || ts->model == 7845) {
 		Rt = ts->pressure_max / 2;
-	} else if (ts->model == 7845) {
-		if (get_pendown_state(ts))
-			Rt = ts->pressure_max / 2;
-		else
-			Rt = 0;
-		dev_vdbg(&ts->spi->dev, "x/y: %d/%d, PD %d\n", x, y, Rt);
 	} else if (likely(x && z1)) {
 		/* compute touch pressure resistance using equation #2 */
 		Rt = z2;
@@ -1074,6 +1068,9 @@
 		struct ads7846_buf_layout *l = &packet->l[cmd_idx];
 		unsigned int max_count;
 
+		if (cmd_idx == packet->cmds - 1)
+			cmd_idx = ADS7846_PWDOWN;
+
 		if (ads7846_cmd_need_settle(cmd_idx))
 			max_count = packet->count + packet->count_skip;
 		else
@@ -1110,7 +1107,12 @@
 
 	for (cmd_idx = 0; cmd_idx < packet->cmds; cmd_idx++) {
 		struct ads7846_buf_layout *l = &packet->l[cmd_idx];
-		u8 cmd = ads7846_get_cmd(cmd_idx, vref);
+		u8 cmd;
+
+		if (cmd_idx == packet->cmds - 1)
+			cmd_idx = ADS7846_PWDOWN;
+
+		cmd = ads7846_get_cmd(cmd_idx, vref);
 
 		for (b = 0; b < l->count; b++)
 			packet->tx[l->offset + b].cmd = cmd;
@@ -1323,8 +1325,9 @@
 			pdata->y_min ? : 0,
 			pdata->y_max ? : MAX_12BIT,
 			0, 0);
-	input_set_abs_params(input_dev, ABS_PRESSURE,
-			pdata->pressure_min, pdata->pressure_max, 0, 0);
+	if (ts->model != 7845)
+		input_set_abs_params(input_dev, ABS_PRESSURE,
+				pdata->pressure_min, pdata->pressure_max, 0, 0);
 
 	/*
 	 * Parse common framework properties. Must be done here to ensure the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/atmel_mxt_ts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/atmel_mxt_ts.c
@@ -1882,7 +1882,7 @@
 	if (error) {
 		dev_err(&client->dev, "Error %d parsing object table\n", error);
 		mxt_free_object_table(data);
-		goto err_free_mem;
+		return error;
 	}
 
 	data->object_table = (struct mxt_object *)(id_buf + MXT_OBJECT_START);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/cyttsp4_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/cyttsp4_core.c
@@ -1263,9 +1263,8 @@
 	 * Ensure we wait until the watchdog timer
 	 * running on a different CPU finishes
 	 */
-	del_timer_sync(&cd->watchdog_timer);
+	timer_shutdown_sync(&cd->watchdog_timer);
 	cancel_work_sync(&cd->watchdog_work);
-	del_timer_sync(&cd->watchdog_timer);
 }
 
 static void cyttsp4_watchdog_timer(struct timer_list *t)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/elants_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/elants_i2c.c
@@ -117,6 +117,19 @@
 #define ELAN_POWERON_DELAY_USEC	500
 #define ELAN_RESET_DELAY_MSEC	20
 
+/* FW boot code version */
+#define BC_VER_H_BYTE_FOR_EKTH3900x1_I2C        0x72
+#define BC_VER_H_BYTE_FOR_EKTH3900x2_I2C        0x82
+#define BC_VER_H_BYTE_FOR_EKTH3900x3_I2C        0x92
+#define BC_VER_H_BYTE_FOR_EKTH5312x1_I2C        0x6D
+#define BC_VER_H_BYTE_FOR_EKTH5312x2_I2C        0x6E
+#define BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C       0x77
+#define BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C       0x78
+#define BC_VER_H_BYTE_FOR_EKTH5312x1_I2C_USB    0x67
+#define BC_VER_H_BYTE_FOR_EKTH5312x2_I2C_USB    0x68
+#define BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C_USB   0x74
+#define BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C_USB   0x75
+
 enum elants_chip_id {
 	EKTH3500,
 	EKTF3624,
@@ -736,6 +749,37 @@
 	return 0;
 }
 
+static bool elants_i2c_should_check_remark_id(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	const u8 bootcode_version = ts->iap_version;
+	bool check;
+
+	/* I2C eKTH3900 and eKTH5312 are NOT support Remark ID */
+	if ((bootcode_version == BC_VER_H_BYTE_FOR_EKTH3900x1_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH3900x2_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH3900x3_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x1_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x2_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x1_I2C_USB) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312x2_I2C_USB) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx1_I2C_USB) ||
+	    (bootcode_version == BC_VER_H_BYTE_FOR_EKTH5312cx2_I2C_USB)) {
+		dev_dbg(&client->dev,
+			"eKTH3900/eKTH5312(0x%02x) are not support remark id\n",
+			bootcode_version);
+		check = false;
+	} else if (bootcode_version >= 0x60) {
+		check = true;
+	} else {
+		check = false;
+	}
+
+	return check;
+}
+
 static int elants_i2c_do_update_firmware(struct i2c_client *client,
 					 const struct firmware *fw,
 					 bool force)
@@ -749,7 +793,7 @@
 	u16 send_id;
 	int page, n_fw_pages;
 	int error;
-	bool check_remark_id = ts->iap_version >= 0x60;
+	bool check_remark_id = elants_i2c_should_check_remark_id(ts);
 
 	/* Recovery mode detection! */
 	if (force) {
@@ -1285,14 +1329,12 @@
 	if (IS_ERR_OR_NULL(ts->reset_gpio))
 		return 0;
 
-	gpiod_set_value_cansleep(ts->reset_gpio, 1);
-
 	error = regulator_enable(ts->vcc33);
 	if (error) {
 		dev_err(&ts->client->dev,
 			"failed to enable vcc33 regulator: %d\n",
 			error);
-		goto release_reset_gpio;
+		return error;
 	}
 
 	error = regulator_enable(ts->vccio);
@@ -1301,7 +1343,7 @@
 			"failed to enable vccio regulator: %d\n",
 			error);
 		regulator_disable(ts->vcc33);
-		goto release_reset_gpio;
+		return error;
 	}
 
 	/*
@@ -1310,7 +1352,6 @@
 	 */
 	udelay(ELAN_POWERON_DELAY_USEC);
 
-release_reset_gpio:
 	gpiod_set_value_cansleep(ts->reset_gpio, 0);
 	if (error)
 		return error;
@@ -1418,7 +1459,7 @@
 		return error;
 	}
 
-	ts->reset_gpio = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+	ts->reset_gpio = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(ts->reset_gpio)) {
 		error = PTR_ERR(ts->reset_gpio);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/exc3000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/exc3000.c
@@ -220,6 +220,7 @@
 {
 	u8 buf[EXC3000_LEN_VENDOR_REQUEST] = { 0x67, 0x00, 0x42, 0x00, 0x03 };
 	int ret;
+	unsigned long time_left;
 
 	mutex_lock(&data->query_lock);
 
@@ -233,9 +234,9 @@
 		goto out_unlock;
 
 	if (response) {
-		ret = wait_for_completion_timeout(&data->wait_event,
-						  timeout * HZ);
-		if (ret <= 0) {
+		time_left = wait_for_completion_timeout(&data->wait_event,
+							timeout * HZ);
+		if (time_left == 0) {
 			ret = -ETIMEDOUT;
 			goto out_unlock;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/goodix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/goodix.c
@@ -14,20 +14,16 @@
 #include <linux/kernel.h>
 #include <linux/dmi.h>
 #include <linux/firmware.h>
-#include <linux/gpio/consumer.h>
-#include <linux/i2c.h>
-#include <linux/input.h>
-#include <linux/input/mt.h>
-#include <linux/input/touchscreen.h>
 #include <linux/module.h>
 #include <linux/delay.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
-#include <linux/regulator/consumer.h>
+#include <linux/platform_data/x86/soc.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
 #include <linux/of.h>
 #include <asm/unaligned.h>
+#include "goodix.h"
 
 #define GOODIX_GPIO_INT_NAME		"irq"
 #define GOODIX_GPIO_RST_NAME		"reset"
@@ -38,22 +34,11 @@
 #define GOODIX_CONTACT_SIZE		8
 #define GOODIX_MAX_CONTACT_SIZE		9
 #define GOODIX_MAX_CONTACTS		10
-#define GOODIX_MAX_KEYS			7
 
 #define GOODIX_CONFIG_MIN_LENGTH	186
 #define GOODIX_CONFIG_911_LENGTH	186
 #define GOODIX_CONFIG_967_LENGTH	228
 #define GOODIX_CONFIG_GT9X_LENGTH	240
-#define GOODIX_CONFIG_MAX_LENGTH	240
-
-/* Register defines */
-#define GOODIX_REG_COMMAND		0x8040
-#define GOODIX_CMD_SCREEN_OFF		0x05
-
-#define GOODIX_READ_COOR_ADDR		0x814E
-#define GOODIX_GT1X_REG_CONFIG_DATA	0x8050
-#define GOODIX_GT9X_REG_CONFIG_DATA	0x8047
-#define GOODIX_REG_ID			0x8140
 
 #define GOODIX_BUFFER_STATUS_READY	BIT(7)
 #define GOODIX_HAVE_KEY			BIT(4)
@@ -68,55 +53,11 @@
 #define ACPI_GPIO_SUPPORT
 #endif
 
-struct goodix_ts_data;
-
-enum goodix_irq_pin_access_method {
-	IRQ_PIN_ACCESS_NONE,
-	IRQ_PIN_ACCESS_GPIO,
-	IRQ_PIN_ACCESS_ACPI_GPIO,
-	IRQ_PIN_ACCESS_ACPI_METHOD,
-};
-
-struct goodix_chip_data {
-	u16 config_addr;
-	int config_len;
-	int (*check_config)(struct goodix_ts_data *ts, const u8 *cfg, int len);
-	void (*calc_config_checksum)(struct goodix_ts_data *ts);
-};
-
 struct goodix_chip_id {
 	const char *id;
 	const struct goodix_chip_data *data;
 };
 
-#define GOODIX_ID_MAX_LEN	4
-
-struct goodix_ts_data {
-	struct i2c_client *client;
-	struct input_dev *input_dev;
-	const struct goodix_chip_data *chip;
-	struct touchscreen_properties prop;
-	unsigned int max_touch_num;
-	unsigned int int_trigger_type;
-	struct regulator *avdd28;
-	struct regulator *vddio;
-	struct gpio_desc *gpiod_int;
-	struct gpio_desc *gpiod_rst;
-	int gpio_count;
-	int gpio_int_idx;
-	char id[GOODIX_ID_MAX_LEN + 1];
-	u16 version;
-	const char *cfg_name;
-	bool reset_controller_at_probe;
-	bool load_cfg_from_disk;
-	struct completion firmware_loading_complete;
-	unsigned long irq_flags;
-	enum goodix_irq_pin_access_method irq_pin_access_method;
-	unsigned int contact_size;
-	u8 config[GOODIX_CONFIG_MAX_LENGTH];
-	unsigned short keymap[GOODIX_MAX_KEYS];
-};
-
 static int goodix_check_cfg_8(struct goodix_ts_data *ts,
 			      const u8 *cfg, int len);
 static int goodix_check_cfg_16(struct goodix_ts_data *ts,
@@ -154,6 +95,7 @@
 
 static const struct goodix_chip_id goodix_chip_ids[] = {
 	{ .id = "1151", .data = &gt1x_chip_data },
+	{ .id = "1158", .data = &gt1x_chip_data },
 	{ .id = "5663", .data = &gt1x_chip_data },
 	{ .id = "5688", .data = &gt1x_chip_data },
 	{ .id = "917S", .data = &gt1x_chip_data },
@@ -162,6 +104,7 @@
 	{ .id = "911", .data = &gt911_chip_data },
 	{ .id = "9271", .data = &gt911_chip_data },
 	{ .id = "9110", .data = &gt911_chip_data },
+	{ .id = "9111", .data = &gt911_chip_data },
 	{ .id = "927", .data = &gt911_chip_data },
 	{ .id = "928", .data = &gt911_chip_data },
 
@@ -181,10 +124,18 @@
 static const struct dmi_system_id nine_bytes_report[] = {
 #if defined(CONFIG_DMI) && defined(CONFIG_X86)
 	{
-		.ident = "Lenovo YogaBook",
-		/* YB1-X91L/F and YB1-X90L/F */
+		/* Lenovo Yoga Book X90F / X90L */
 		.matches = {
-			DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X9")
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Intel Corporation"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "CHERRYVIEW D1 PLATFORM"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "YETI-11"),
+		}
+	},
+	{
+		/* Lenovo Yoga Book X91F / X91L */
+		.matches = {
+			/* Non exact match to match F + L versions */
+			DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X91"),
 		}
 	},
 #endif
@@ -215,8 +166,7 @@
  * @buf: raw write data buffer.
  * @len: length of the buffer to write
  */
-static int goodix_i2c_read(struct i2c_client *client,
-			   u16 reg, u8 *buf, int len)
+int goodix_i2c_read(struct i2c_client *client, u16 reg, u8 *buf, int len)
 {
 	struct i2c_msg msgs[2];
 	__be16 wbuf = cpu_to_be16(reg);
@@ -244,8 +194,7 @@
  * @buf: raw data buffer to write.
  * @len: length of the buffer to write
  */
-static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
-			    unsigned len)
+int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf, int len)
 {
 	u8 *addr_buf;
 	struct i2c_msg msg;
@@ -269,7 +218,7 @@
 	return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
 }
 
-static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
+int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
 {
 	return goodix_i2c_write(client, reg, &value, sizeof(value));
 }
@@ -553,7 +502,7 @@
  * @cfg: config firmware to write to device
  * @len: config data length
  */
-static int goodix_send_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len)
+int goodix_send_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len)
 {
 	int error;
 
@@ -651,80 +600,91 @@
 	return -EINVAL; /* Never reached */
 }
 
-static int goodix_int_sync(struct goodix_ts_data *ts)
+int goodix_int_sync(struct goodix_ts_data *ts)
 {
 	int error;
 
 	error = goodix_irq_direction_output(ts, 0);
 	if (error)
-		return error;
+		goto error;
 
 	msleep(50);				/* T5: 50ms */
 
 	error = goodix_irq_direction_input(ts);
 	if (error)
-		return error;
+		goto error;
 
 	return 0;
+
+error:
+	dev_err(&ts->client->dev, "Controller irq sync failed.\n");
+	return error;
 }
 
 /**
- * goodix_reset - Reset device during power on
+ * goodix_reset_no_int_sync - Reset device, leaving interrupt line in output mode
  *
  * @ts: goodix_ts_data pointer
  */
-static int goodix_reset(struct goodix_ts_data *ts)
+int goodix_reset_no_int_sync(struct goodix_ts_data *ts)
 {
 	int error;
 
 	/* begin select I2C slave addr */
 	error = gpiod_direction_output(ts->gpiod_rst, 0);
 	if (error)
-		return error;
+		goto error;
 
 	msleep(20);				/* T2: > 10ms */
 
 	/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
 	error = goodix_irq_direction_output(ts, ts->client->addr == 0x14);
 	if (error)
-		return error;
+		goto error;
 
 	usleep_range(100, 2000);		/* T3: > 100us */
 
 	error = gpiod_direction_output(ts->gpiod_rst, 1);
 	if (error)
-		return error;
+		goto error;
 
 	usleep_range(6000, 10000);		/* T4: > 5ms */
 
-	/* end select I2C slave addr */
-	error = gpiod_direction_input(ts->gpiod_rst);
-	if (error)
-		return error;
-
-	error = goodix_int_sync(ts);
-	if (error)
-		return error;
+	/*
+	 * Put the reset pin back in to input / high-impedance mode to save
+	 * power. Only do this in the non ACPI case since some ACPI boards
+	 * don't have a pull-up, so there the reset pin must stay active-high.
+	 */
+	if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_GPIO) {
+		error = gpiod_direction_input(ts->gpiod_rst);
+		if (error)
+			goto error;
+	}
 
 	return 0;
-}
 
-#ifdef ACPI_GPIO_SUPPORT
-#include <asm/cpu_device_id.h>
-#include <asm/intel-family.h>
-
-static const struct x86_cpu_id baytrail_cpu_ids[] = {
-	{ X86_VENDOR_INTEL, 6, INTEL_FAM6_ATOM_SILVERMONT, X86_FEATURE_ANY, },
-	{}
-};
+error:
+	dev_err(&ts->client->dev, "Controller reset failed.\n");
+	return error;
+}
 
-static inline bool is_byt(void)
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
 {
-	const struct x86_cpu_id *id = x86_match_cpu(baytrail_cpu_ids);
+	int error;
 
-	return !!id;
+	error = goodix_reset_no_int_sync(ts);
+	if (error)
+		return error;
+
+	return goodix_int_sync(ts);
 }
 
+#ifdef ACPI_GPIO_SUPPORT
 static const struct acpi_gpio_params first_gpio = { 0, 0, false };
 static const struct acpi_gpio_params second_gpio = { 1, 0, false };
 
@@ -808,16 +768,43 @@
 		dev_info(dev, "Using ACPI INTI and INTO methods for IRQ pin access\n");
 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_METHOD;
 		gpio_mapping = acpi_goodix_reset_only_gpios;
-	} else if (is_byt() && ts->gpio_count == 2 && ts->gpio_int_idx == -1) {
+	} else if (soc_intel_is_byt() && ts->gpio_count == 2 && ts->gpio_int_idx == -1) {
 		dev_info(dev, "No ACPI GpioInt resource, assuming that the GPIO order is reset, int\n");
 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
 		gpio_mapping = acpi_goodix_int_last_gpios;
+	} else if (ts->gpio_count == 1 && ts->gpio_int_idx == 0) {
+		/*
+		 * On newer devices there is only 1 GpioInt resource and _PS0
+		 * does the whole reset sequence for us.
+		 */
+		acpi_device_fix_up_power(ACPI_COMPANION(dev));
+
+		/*
+		 * Before the _PS0 call the int GPIO may have been in output
+		 * mode and the call should have put the int GPIO in input mode,
+		 * but the GPIO subsys cached state may still think it is
+		 * in output mode, causing gpiochip_lock_as_irq() failure.
+		 *
+		 * Add a mapping for the int GPIO to make the
+		 * gpiod_int = gpiod_get(..., GPIOD_IN) call succeed,
+		 * which will explicitly set the direction to input.
+		 */
+		ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE;
+		gpio_mapping = acpi_goodix_int_first_gpios;
 	} else {
 		dev_warn(dev, "Unexpected ACPI resources: gpio_count %d, gpio_int_idx %d\n",
 			 ts->gpio_count, ts->gpio_int_idx);
 		return -EINVAL;
 	}
 
+	/*
+	 * Normally we put the reset pin in input / high-impedance mode to save
+	 * power. But some x86/ACPI boards don't have a pull-up, so for the ACPI
+	 * case, leave the pin as is. This results in the pin not being touched
+	 * at all on x86/ACPI boards, except when needed for error-recover.
+	 */
+	ts->gpiod_rst_flags = GPIOD_ASIS;
+
 	return devm_acpi_dev_add_driver_gpios(dev, gpio_mapping);
 }
 #else
@@ -843,6 +830,12 @@
 		return -EINVAL;
 	dev = &ts->client->dev;
 
+	/*
+	 * By default we request the reset pin as input, leaving it in
+	 * high-impedance when not resetting the controller to save power.
+	 */
+	ts->gpiod_rst_flags = GPIOD_IN;
+
 	ts->avdd28 = devm_regulator_get(dev, "AVDD28");
 	if (IS_ERR(ts->avdd28)) {
 		error = PTR_ERR(ts->avdd28);
@@ -880,7 +873,7 @@
 	ts->gpiod_int = gpiod;
 
 	/* Get the reset line GPIO pin number */
-	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN);
+	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, ts->gpiod_rst_flags);
 	if (IS_ERR(gpiod)) {
 		error = PTR_ERR(gpiod);
 		if (error != -EPROBE_DEFER)
@@ -1059,6 +1052,7 @@
 	input_set_abs_params(ts->input_dev, ABS_MT_WIDTH_MAJOR, 0, 255, 0, 0);
 	input_set_abs_params(ts->input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
 
+retry_read_config:
 	/* Read configuration and apply touchscreen parameters */
 	goodix_read_config(ts);
 
@@ -1066,6 +1060,16 @@
 	touchscreen_parse_properties(ts->input_dev, true, &ts->prop);
 
 	if (!ts->prop.max_x || !ts->prop.max_y || !ts->max_touch_num) {
+		if (!ts->reset_controller_at_probe &&
+		    ts->irq_pin_access_method != IRQ_PIN_ACCESS_NONE) {
+			dev_info(&ts->client->dev, "Config not set, resetting controller\n");
+			/* Retry after a controller reset */
+			ts->reset_controller_at_probe = true;
+			error = goodix_reset(ts);
+			if (error)
+				return error;
+			goto retry_read_config;
+		}
 		dev_err(&ts->client->dev,
 			"Invalid config (%d, %d, %d), using defaults\n",
 			ts->prop.max_x, ts->prop.max_y, ts->max_touch_num);
@@ -1205,10 +1209,8 @@
 	if (ts->reset_controller_at_probe) {
 		/* reset the controller */
 		error = goodix_reset(ts);
-		if (error) {
-			dev_err(&client->dev, "Controller reset failed.\n");
+		if (error)
 			return error;
-		}
 	}
 
 	error = goodix_i2c_test(client);
@@ -1350,10 +1352,8 @@
 
 	if (error != 0 || config_ver != ts->config[0]) {
 		error = goodix_reset(ts);
-		if (error) {
-			dev_err(dev, "Controller reset failed.\n");
+		if (error)
 			return error;
-		}
 
 		error = goodix_send_cfg(ts, ts->config, ts->chip->config_len);
 		if (error)
@@ -1387,6 +1387,7 @@
 #ifdef CONFIG_OF
 static const struct of_device_id goodix_of_match[] = {
 	{ .compatible = "goodix,gt1151" },
+	{ .compatible = "goodix,gt1158" },
 	{ .compatible = "goodix,gt5663" },
 	{ .compatible = "goodix,gt5688" },
 	{ .compatible = "goodix,gt911" },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/goodix.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/goodix.h
@@ -0,0 +1,75 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef __GOODIX_H__
+#define __GOODIX_H__
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/regulator/consumer.h>
+
+/* Register defines */
+#define GOODIX_REG_COMMAND			0x8040
+#define GOODIX_CMD_SCREEN_OFF			0x05
+
+#define GOODIX_GT1X_REG_CONFIG_DATA		0x8050
+#define GOODIX_GT9X_REG_CONFIG_DATA		0x8047
+#define GOODIX_REG_ID				0x8140
+#define GOODIX_READ_COOR_ADDR			0x814E
+
+#define GOODIX_ID_MAX_LEN			4
+#define GOODIX_CONFIG_MAX_LENGTH		240
+#define GOODIX_MAX_KEYS				7
+
+enum goodix_irq_pin_access_method {
+	IRQ_PIN_ACCESS_NONE,
+	IRQ_PIN_ACCESS_GPIO,
+	IRQ_PIN_ACCESS_ACPI_GPIO,
+	IRQ_PIN_ACCESS_ACPI_METHOD,
+};
+
+struct goodix_ts_data;
+
+struct goodix_chip_data {
+	u16 config_addr;
+	int config_len;
+	int (*check_config)(struct goodix_ts_data *ts, const u8 *cfg, int len);
+	void (*calc_config_checksum)(struct goodix_ts_data *ts);
+};
+
+struct goodix_ts_data {
+	struct i2c_client *client;
+	struct input_dev *input_dev;
+	const struct goodix_chip_data *chip;
+	struct touchscreen_properties prop;
+	unsigned int max_touch_num;
+	unsigned int int_trigger_type;
+	struct regulator *avdd28;
+	struct regulator *vddio;
+	struct gpio_desc *gpiod_int;
+	struct gpio_desc *gpiod_rst;
+	int gpio_count;
+	int gpio_int_idx;
+	enum gpiod_flags gpiod_rst_flags;
+	char id[GOODIX_ID_MAX_LEN + 1];
+	u16 version;
+	const char *cfg_name;
+	bool reset_controller_at_probe;
+	bool load_cfg_from_disk;
+	struct completion firmware_loading_complete;
+	unsigned long irq_flags;
+	enum goodix_irq_pin_access_method irq_pin_access_method;
+	unsigned int contact_size;
+	u8 config[GOODIX_CONFIG_MAX_LENGTH];
+	unsigned short keymap[GOODIX_MAX_KEYS];
+};
+
+int goodix_i2c_read(struct i2c_client *client, u16 reg, u8 *buf, int len);
+int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf, int len);
+int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value);
+int goodix_send_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len);
+int goodix_int_sync(struct goodix_ts_data *ts);
+int goodix_reset_no_int_sync(struct goodix_ts_data *ts);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/ili210x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/ili210x.c
@@ -231,8 +231,8 @@
 	if (!error && data[0] == 2) {
 		error = i2c_master_recv(client, data + ILI251X_DATA_SIZE1,
 					ILI251X_DATA_SIZE2);
-		if (error >= 0 && error != ILI251X_DATA_SIZE2)
-			error = -EIO;
+		if (error >= 0)
+			error = error == ILI251X_DATA_SIZE2 ? 0 : -EIO;
 	}
 
 	return error;
@@ -420,9 +420,9 @@
 		if (error)
 			return error;
 
-		usleep_range(50, 100);
+		usleep_range(12000, 15000);
 		gpiod_set_value_cansleep(reset_gpio, 0);
-		msleep(100);
+		msleep(160);
 	}
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/ilitek_ts_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/ilitek_ts_i2c.c
@@ -37,6 +37,8 @@
 #define ILITEK_TP_CMD_GET_MCU_VER			0x61
 #define ILITEK_TP_CMD_GET_IC_MODE			0xC0
 
+#define ILITEK_TP_I2C_REPORT_ID				0x48
+
 #define REPORT_COUNT_ADDRESS				61
 #define ILITEK_SUPPORT_MAX_POINT			40
 
@@ -160,15 +162,19 @@
 	error = ilitek_i2c_write_and_read(ts, NULL, 0, 0, buf, 64);
 	if (error) {
 		dev_err(dev, "get touch info failed, err:%d\n", error);
-		goto err_sync_frame;
+		return error;
+	}
+
+	if (buf[0] != ILITEK_TP_I2C_REPORT_ID) {
+		dev_err(dev, "get touch info failed. Wrong id: 0x%02X\n", buf[0]);
+		return -EINVAL;
 	}
 
 	report_max_point = buf[REPORT_COUNT_ADDRESS];
 	if (report_max_point > ts->max_tp) {
 		dev_err(dev, "FW report max point:%d > panel info. max:%d\n",
 			report_max_point, ts->max_tp);
-		error = -EINVAL;
-		goto err_sync_frame;
+		return -EINVAL;
 	}
 
 	count = DIV_ROUND_UP(report_max_point, packet_max_point);
@@ -178,7 +184,7 @@
 		if (error) {
 			dev_err(dev, "get touch info. failed, cnt:%d, err:%d\n",
 				count, error);
-			goto err_sync_frame;
+			return error;
 		}
 	}
 
@@ -203,10 +209,10 @@
 		ilitek_touch_down(ts, id, x, y);
 	}
 
-err_sync_frame:
 	input_mt_sync_frame(input);
 	input_sync(input);
-	return error;
+
+	return 0;
 }
 
 /* APIs of cmds for ILITEK Touch IC */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/melfas_mip4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/melfas_mip4.c
@@ -1453,7 +1453,7 @@
 					      "ce", GPIOD_OUT_LOW);
 	if (IS_ERR(ts->gpio_ce)) {
 		error = PTR_ERR(ts->gpio_ce);
-		if (error != EPROBE_DEFER)
+		if (error != -EPROBE_DEFER)
 			dev_err(&client->dev,
 				"Failed to get gpio: %d\n", error);
 		return error;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/raspberrypi-ts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/raspberrypi-ts.c
@@ -134,7 +134,7 @@
 		return -ENOENT;
 	}
 
-	fw = rpi_firmware_get(fw_node);
+	fw = devm_rpi_firmware_get(&pdev->dev, fw_node);
 	of_node_put(fw_node);
 	if (!fw)
 		return -EPROBE_DEFER;
@@ -160,7 +160,6 @@
 	touchbuf = (u32)ts->fw_regs_phys;
 	error = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF,
 				      &touchbuf, sizeof(touchbuf));
-	rpi_firmware_put(fw);
 	if (error || touchbuf != 0) {
 		dev_warn(dev, "Failed to set touchbuf, %d\n", error);
 		return error;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/raydium_i2c_ts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/raydium_i2c_ts.c
@@ -210,12 +210,14 @@
 
 		error = raydium_i2c_xfer(client, addr, xfer, ARRAY_SIZE(xfer));
 		if (likely(!error))
-			return 0;
+			goto out;
 
 		msleep(RM_RETRY_DELAY_MS);
 	} while (++tries < RM_MAX_RETRIES);
 
 	dev_err(&client->dev, "%s failed: %d\n", __func__, error);
+out:
+	kfree(tx_buf);
 	return error;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/silead.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/silead.c
@@ -70,7 +70,6 @@
 	struct regulator_bulk_data regulators[2];
 	char fw_name[64];
 	struct touchscreen_properties prop;
-	u32 max_fingers;
 	u32 chip_id;
 	struct input_mt_pos pos[SILEAD_MAX_FINGERS];
 	int slots[SILEAD_MAX_FINGERS];
@@ -98,7 +97,7 @@
 	input_set_abs_params(data->input, ABS_MT_POSITION_Y, 0, 4095, 0, 0);
 	touchscreen_parse_properties(data->input, true, &data->prop);
 
-	input_mt_init_slots(data->input, data->max_fingers,
+	input_mt_init_slots(data->input, SILEAD_MAX_FINGERS,
 			    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED |
 			    INPUT_MT_TRACK);
 
@@ -145,10 +144,10 @@
 		return;
 	}
 
-	if (buf[0] > data->max_fingers) {
+	if (buf[0] > SILEAD_MAX_FINGERS) {
 		dev_warn(dev, "More touches reported then supported %d > %d\n",
-			 buf[0], data->max_fingers);
-		buf[0] = data->max_fingers;
+			 buf[0], SILEAD_MAX_FINGERS);
+		buf[0] = SILEAD_MAX_FINGERS;
 	}
 
 	touch_nr = 0;
@@ -200,7 +199,6 @@
 
 static int silead_ts_init(struct i2c_client *client)
 {
-	struct silead_ts_data *data = i2c_get_clientdata(client);
 	int error;
 
 	error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
@@ -210,7 +208,7 @@
 	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
 
 	error = i2c_smbus_write_byte_data(client, SILEAD_REG_TOUCH_NR,
-					data->max_fingers);
+					  SILEAD_MAX_FINGERS);
 	if (error)
 		goto i2c_write_err;
 	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
@@ -437,13 +435,6 @@
 	const char *str;
 	int error;
 
-	error = device_property_read_u32(dev, "silead,max-fingers",
-					 &data->max_fingers);
-	if (error) {
-		dev_dbg(dev, "Max fingers read error %d\n", error);
-		data->max_fingers = 5; /* Most devices handle up-to 5 fingers */
-	}
-
 	error = device_property_read_string(dev, "firmware-name", &str);
 	if (!error)
 		snprintf(data->fw_name, sizeof(data->fw_name),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/st1232.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/st1232.c
@@ -92,7 +92,7 @@
 	unsigned int retries;
 	int error;
 
-	for (retries = 10; retries; retries--) {
+	for (retries = 100; retries; retries--) {
 		error = st1232_ts_read_data(ts, REG_STATUS, 1);
 		if (!error) {
 			switch (ts->read_buf[0]) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/stmfts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/stmfts.c
@@ -337,13 +337,15 @@
 	struct stmfts_data *sdata = input_get_drvdata(dev);
 	int err;
 
-	err = pm_runtime_get_sync(&sdata->client->dev);
-	if (err < 0)
+	err = pm_runtime_resume_and_get(&sdata->client->dev);
+	if (err)
 		return err;
 
 	err = i2c_smbus_write_byte(sdata->client, STMFTS_MS_MT_SENSE_ON);
-	if (err)
+	if (err) {
+		pm_runtime_put_sync(&sdata->client->dev);
 		return err;
+	}
 
 	mutex_lock(&sdata->mutex);
 	sdata->running = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/ti_am335x_tsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -131,7 +131,8 @@
 	u32 stepenable;
 
 	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_AVG_16 | ts_dev->bit_xp;
+			STEPCONFIG_AVG_16 | ts_dev->bit_xp |
+			STEPCONFIG_INM_ADCREFM;
 	switch (ts_dev->wires) {
 	case 4:
 		config |= STEPCONFIG_INP(ts_dev->inp_yp) | ts_dev->bit_xn;
@@ -195,7 +196,10 @@
 			STEPCONFIG_OPENDLY);
 
 	end_step++;
-	config |= STEPCONFIG_INP(ts_dev->inp_yn);
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_AVG_16 | ts_dev->bit_yp |
+			ts_dev->bit_xn | STEPCONFIG_INM_ADCREFM |
+			STEPCONFIG_INP(ts_dev->inp_yn);
 	titsc_writel(ts_dev, REG_STEPCONFIG(end_step), config);
 	titsc_writel(ts_dev, REG_STEPDELAY(end_step),
 			STEPCONFIG_OPENDLY);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/input/touchscreen/zinitix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/input/touchscreen/zinitix.c
@@ -135,7 +135,7 @@
 
 struct touch_event {
 	__le16	status;
-	u8	finger_cnt;
+	u8	finger_mask;
 	u8	time_stamp;
 	struct point_coord point_coord[MAX_SUPPORTED_FINGER_NUM];
 };
@@ -311,11 +311,32 @@
 static void zinitix_report_finger(struct bt541_ts_data *bt541, int slot,
 				  const struct point_coord *p)
 {
+	u16 x, y;
+
+	if (unlikely(!(p->sub_status &
+		       (SUB_BIT_UP | SUB_BIT_DOWN | SUB_BIT_MOVE)))) {
+		dev_dbg(&bt541->client->dev, "unknown finger event %#02x\n",
+			p->sub_status);
+		return;
+	}
+
+	x = le16_to_cpu(p->x);
+	y = le16_to_cpu(p->y);
+
 	input_mt_slot(bt541->input_dev, slot);
-	input_mt_report_slot_state(bt541->input_dev, MT_TOOL_FINGER, true);
-	touchscreen_report_pos(bt541->input_dev, &bt541->prop,
-			       le16_to_cpu(p->x), le16_to_cpu(p->y), true);
-	input_report_abs(bt541->input_dev, ABS_MT_TOUCH_MAJOR, p->width);
+	if (input_mt_report_slot_state(bt541->input_dev, MT_TOOL_FINGER,
+				       !(p->sub_status & SUB_BIT_UP))) {
+		touchscreen_report_pos(bt541->input_dev,
+				       &bt541->prop, x, y, true);
+		input_report_abs(bt541->input_dev,
+				 ABS_MT_TOUCH_MAJOR, p->width);
+		dev_dbg(&bt541->client->dev, "finger %d %s (%u, %u)\n",
+			slot, p->sub_status & SUB_BIT_DOWN ? "down" : "move",
+			x, y);
+	} else {
+		dev_dbg(&bt541->client->dev, "finger %d up (%u, %u)\n",
+			slot, x, y);
+	}
 }
 
 static irqreturn_t zinitix_ts_irq_handler(int irq, void *bt541_handler)
@@ -323,6 +344,7 @@
 	struct bt541_ts_data *bt541 = bt541_handler;
 	struct i2c_client *client = bt541->client;
 	struct touch_event touch_event;
+	unsigned long finger_mask;
 	int error;
 	int i;
 
@@ -335,10 +357,14 @@
 		goto out;
 	}
 
-	for (i = 0; i < MAX_SUPPORTED_FINGER_NUM; i++)
-		if (touch_event.point_coord[i].sub_status & SUB_BIT_EXIST)
-			zinitix_report_finger(bt541, i,
-					      &touch_event.point_coord[i]);
+	finger_mask = touch_event.finger_mask;
+	for_each_set_bit(i, &finger_mask, MAX_SUPPORTED_FINGER_NUM) {
+		const struct point_coord *p = &touch_event.point_coord[i];
+
+		/* Only process contacts that are actually reported */
+		if (p->sub_status & SUB_BIT_EXIST)
+			zinitix_report_finger(bt541, i, p);
+	}
 
 	input_mt_sync_frame(bt541->input_dev);
 	input_sync(bt541->input_dev);
@@ -488,6 +514,15 @@
 		return error;
 	}
 
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, zinitix_ts_irq_handler,
+					  IRQF_ONESHOT | IRQF_NO_AUTOEN,
+					  client->name, bt541);
+	if (error) {
+		dev_err(&client->dev, "Failed to request IRQ: %d\n", error);
+		return error;
+	}
+
 	error = zinitix_init_input_dev(bt541);
 	if (error) {
 		dev_err(&client->dev,
@@ -513,15 +548,6 @@
 		return -EINVAL;
 	}
 
-	error = devm_request_threaded_irq(&client->dev, client->irq,
-					  NULL, zinitix_ts_irq_handler,
-					  IRQF_ONESHOT | IRQF_NO_AUTOEN,
-					  client->name, bt541);
-	if (error) {
-		dev_err(&client->dev, "Failed to request IRQ: %d\n", error);
-		return error;
-	}
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/core.c
@@ -13,6 +13,7 @@
 #include <linux/interconnect.h>
 #include <linux/interconnect-provider.h>
 #include <linux/list.h>
+#include <linux/sched/mm.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
@@ -380,6 +381,9 @@
 	}
 	mutex_unlock(&icc_lock);
 
+	if (!node)
+		return ERR_PTR(-EINVAL);
+
 	if (IS_ERR(node))
 		return ERR_CAST(node);
 
@@ -850,6 +854,10 @@
 
 	mutex_unlock(&icc_lock);
 
+	if (!node)
+		return;
+
+	kfree(node->links);
 	kfree(node);
 }
 EXPORT_SYMBOL_GPL(icc_node_destroy);
@@ -1087,9 +1095,15 @@
 {
 	struct device_node *child;
 	int count = 0;
+	const struct of_device_id __maybe_unused ignore_list[] = {
+		{ .compatible = "qcom,sc7180-ipa-virt" },
+		{ .compatible = "qcom,sdx55-ipa-virt" },
+		{}
+	};
 
 	for_each_available_child_of_node(np, child) {
-		if (of_property_read_bool(child, "#interconnect-cells"))
+		if (of_property_read_bool(child, "#interconnect-cells") &&
+		    likely(!of_match_node(ignore_list, child)))
 			count++;
 		count += of_count_icc_providers(child);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/imx/imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/imx/imx.c
@@ -226,16 +226,16 @@
 	struct device *dev = &pdev->dev;
 	struct icc_onecell_data *data;
 	struct icc_provider *provider;
-	int max_node_id;
+	int num_nodes;
 	int ret;
 
 	/* icc_onecell_data is indexed by node_id, unlike nodes param */
-	max_node_id = get_max_node_id(nodes, nodes_count);
-	data = devm_kzalloc(dev, struct_size(data, nodes, max_node_id),
+	num_nodes = get_max_node_id(nodes, nodes_count) + 1;
+	data = devm_kzalloc(dev, struct_size(data, nodes, num_nodes),
 			    GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
-	data->num_nodes = max_node_id;
+	data->num_nodes = num_nodes;
 
 	provider = devm_kzalloc(dev, sizeof(*provider), GFP_KERNEL);
 	if (!provider)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/icc-rpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/icc-rpm.c
@@ -68,6 +68,7 @@
 	rate = max(sum_bw, max_peak_bw);
 
 	do_div(rate, qn->buswidth);
+	rate = min_t(u64, rate, LONG_MAX);
 
 	if (qn->rate == rate)
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/icc-rpmh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/icc-rpmh.c
@@ -21,13 +21,18 @@
 {
 	size_t i;
 	struct qcom_icc_node *qn;
+	struct qcom_icc_provider *qp;
 
 	qn = node->data;
+	qp = to_qcom_provider(node->provider);
 
 	for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++) {
 		qn->sum_avg[i] = 0;
 		qn->max_peak[i] = 0;
 	}
+
+	for (i = 0; i < qn->num_bcms; i++)
+		qcom_icc_bcm_voter_add(qp->voter, qn->bcms[i]);
 }
 EXPORT_SYMBOL_GPL(qcom_icc_pre_aggregate);
 
@@ -45,10 +50,8 @@
 {
 	size_t i;
 	struct qcom_icc_node *qn;
-	struct qcom_icc_provider *qp;
 
 	qn = node->data;
-	qp = to_qcom_provider(node->provider);
 
 	if (!tag)
 		tag = QCOM_ICC_TAG_ALWAYS;
@@ -68,9 +71,6 @@
 	*agg_avg += avg_bw;
 	*agg_peak = max_t(u32, *agg_peak, peak_bw);
 
-	for (i = 0; i < qn->num_bcms; i++)
-		qcom_icc_bcm_voter_add(qp->voter, qn->bcms[i]);
-
 	return 0;
 }
 EXPORT_SYMBOL_GPL(qcom_icc_aggregate);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/osm-l3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/osm-l3.c
@@ -275,7 +275,7 @@
 	qnodes = desc->nodes;
 	num_nodes = desc->num_nodes;
 
-	data = devm_kcalloc(&pdev->dev, num_nodes, sizeof(*node), GFP_KERNEL);
+	data = devm_kzalloc(&pdev->dev, struct_size(data, nodes, num_nodes), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/sc7180.c
@@ -47,7 +47,6 @@
 DEFINE_QNODE(qnm_snoc_gc, SC7180_MASTER_SNOC_GC_MEM_NOC, 1, 8, SC7180_SLAVE_LLCC);
 DEFINE_QNODE(qnm_snoc_sf, SC7180_MASTER_SNOC_SF_MEM_NOC, 1, 16, SC7180_SLAVE_LLCC);
 DEFINE_QNODE(qxm_gpu, SC7180_MASTER_GFX3D, 2, 32, SC7180_SLAVE_GEM_NOC_SNOC, SC7180_SLAVE_LLCC);
-DEFINE_QNODE(ipa_core_master, SC7180_MASTER_IPA_CORE, 1, 8, SC7180_SLAVE_IPA_CORE);
 DEFINE_QNODE(llcc_mc, SC7180_MASTER_LLCC, 2, 4, SC7180_SLAVE_EBI1);
 DEFINE_QNODE(qhm_mnoc_cfg, SC7180_MASTER_CNOC_MNOC_CFG, 1, 4, SC7180_SLAVE_SERVICE_MNOC);
 DEFINE_QNODE(qxm_camnoc_hf0, SC7180_MASTER_CAMNOC_HF0, 2, 32, SC7180_SLAVE_MNOC_HF_MEM_NOC);
@@ -129,7 +128,6 @@
 DEFINE_QNODE(qns_gem_noc_snoc, SC7180_SLAVE_GEM_NOC_SNOC, 1, 8, SC7180_MASTER_GEM_NOC_SNOC);
 DEFINE_QNODE(qns_llcc, SC7180_SLAVE_LLCC, 1, 16, SC7180_MASTER_LLCC);
 DEFINE_QNODE(srvc_gemnoc, SC7180_SLAVE_SERVICE_GEM_NOC, 1, 4);
-DEFINE_QNODE(ipa_core_slave, SC7180_SLAVE_IPA_CORE, 1, 8);
 DEFINE_QNODE(ebi, SC7180_SLAVE_EBI1, 2, 4);
 DEFINE_QNODE(qns_mem_noc_hf, SC7180_SLAVE_MNOC_HF_MEM_NOC, 1, 32, SC7180_MASTER_MNOC_HF_MEM_NOC);
 DEFINE_QNODE(qns_mem_noc_sf, SC7180_SLAVE_MNOC_SF_MEM_NOC, 1, 32, SC7180_MASTER_MNOC_SF_MEM_NOC);
@@ -160,7 +158,6 @@
 DEFINE_QBCM(bcm_sh0, "SH0", true, &qns_llcc);
 DEFINE_QBCM(bcm_mm0, "MM0", false, &qns_mem_noc_hf);
 DEFINE_QBCM(bcm_ce0, "CE0", false, &qxm_crypto);
-DEFINE_QBCM(bcm_ip0, "IP0", false, &ipa_core_slave);
 DEFINE_QBCM(bcm_cn0, "CN0", true, &qnm_snoc, &xm_qdss_dap, &qhs_a1_noc_cfg, &qhs_a2_noc_cfg, &qhs_ahb2phy0, &qhs_aop, &qhs_aoss, &qhs_boot_rom, &qhs_camera_cfg, &qhs_camera_nrt_throttle_cfg, &qhs_camera_rt_throttle_cfg, &qhs_clk_ctl, &qhs_cpr_cx, &qhs_cpr_mx, &qhs_crypto0_cfg, &qhs_dcc_cfg, &qhs_ddrss_cfg, &qhs_display_cfg, &qhs_display_rt_throttle_cfg, &qhs_display_throttle_cfg, &qhs_glm, &qhs_gpuss_cfg, &qhs_imem_cfg, &qhs_ipa, &qhs_mnoc_cfg, &qhs_mss_cfg, &qhs_npu_cfg, &qhs_npu_dma_throttle_cfg, &qhs_npu_dsp_throttle_cfg, &qhs_pimem_cfg, &qhs_prng, &qhs_qdss_cfg, &qhs_qm_cfg, &qhs_qm_mpu_cfg, &qhs_qup0, &qhs_qup1, &qhs_security, &qhs_snoc_cfg, &qhs_tcsr, &qhs_tlmm_1, &qhs_tlmm_2, &qhs_tlmm_3, &qhs_ufs_mem_cfg, &qhs_usb3, &qhs_venus_cfg, &qhs_venus_throttle_cfg, &qhs_vsense_ctrl_cfg, &srvc_cnoc);
 DEFINE_QBCM(bcm_mm1, "MM1", false, &qxm_camnoc_hf0_uncomp, &qxm_camnoc_hf1_uncomp, &qxm_camnoc_sf_uncomp, &qhm_mnoc_cfg, &qxm_mdp0, &qxm_rot, &qxm_venus0, &qxm_venus_arm9);
 DEFINE_QBCM(bcm_sh2, "SH2", false, &acm_sys_tcu);
@@ -372,22 +369,6 @@
 	.num_bcms = ARRAY_SIZE(gem_noc_bcms),
 };
 
-static struct qcom_icc_bcm *ipa_virt_bcms[] = {
-	&bcm_ip0,
-};
-
-static struct qcom_icc_node *ipa_virt_nodes[] = {
-	[MASTER_IPA_CORE] = &ipa_core_master,
-	[SLAVE_IPA_CORE] = &ipa_core_slave,
-};
-
-static struct qcom_icc_desc sc7180_ipa_virt = {
-	.nodes = ipa_virt_nodes,
-	.num_nodes = ARRAY_SIZE(ipa_virt_nodes),
-	.bcms = ipa_virt_bcms,
-	.num_bcms = ARRAY_SIZE(ipa_virt_bcms),
-};
-
 static struct qcom_icc_bcm *mc_virt_bcms[] = {
 	&bcm_acv,
 	&bcm_mc0,
@@ -519,8 +500,6 @@
 	  .data = &sc7180_dc_noc},
 	{ .compatible = "qcom,sc7180-gem-noc",
 	  .data = &sc7180_gem_noc},
-	{ .compatible = "qcom,sc7180-ipa-virt",
-	  .data = &sc7180_ipa_virt},
 	{ .compatible = "qcom,sc7180-mc-virt",
 	  .data = &sc7180_mc_virt},
 	{ .compatible = "qcom,sc7180-mmss-noc",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/sdx55.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/sdx55.c
@@ -18,7 +18,6 @@
 #include "icc-rpmh.h"
 #include "sdx55.h"
 
-DEFINE_QNODE(ipa_core_master, SDX55_MASTER_IPA_CORE, 1, 8, SDX55_SLAVE_IPA_CORE);
 DEFINE_QNODE(llcc_mc, SDX55_MASTER_LLCC, 4, 4, SDX55_SLAVE_EBI_CH0);
 DEFINE_QNODE(acm_tcu, SDX55_MASTER_TCU_0, 1, 8, SDX55_SLAVE_LLCC, SDX55_SLAVE_MEM_NOC_SNOC, SDX55_SLAVE_MEM_NOC_PCIE_SNOC);
 DEFINE_QNODE(qnm_snoc_gc, SDX55_MASTER_SNOC_GC_MEM_NOC, 1, 8, SDX55_SLAVE_LLCC);
@@ -40,7 +39,6 @@
 DEFINE_QNODE(xm_qdss_etr, SDX55_MASTER_QDSS_ETR, 1, 8, SDX55_SLAVE_SNOC_CFG, SDX55_SLAVE_EMAC_CFG, SDX55_SLAVE_USB3, SDX55_SLAVE_AOSS, SDX55_SLAVE_SPMI_FETCHER, SDX55_SLAVE_QDSS_CFG, SDX55_SLAVE_PDM, SDX55_SLAVE_SNOC_MEM_NOC_GC, SDX55_SLAVE_TCSR, SDX55_SLAVE_CNOC_DDRSS, SDX55_SLAVE_SPMI_VGI_COEX, SDX55_SLAVE_QPIC, SDX55_SLAVE_OCIMEM, SDX55_SLAVE_IPA_CFG, SDX55_SLAVE_USB3_PHY_CFG, SDX55_SLAVE_AOP, SDX55_SLAVE_BLSP_1, SDX55_SLAVE_SDCC_1, SDX55_SLAVE_CNOC_MSS, SDX55_SLAVE_PCIE_PARF, SDX55_SLAVE_ECC_CFG, SDX55_SLAVE_AUDIO, SDX55_SLAVE_AOSS, SDX55_SLAVE_PRNG, SDX55_SLAVE_CRYPTO_0_CFG, SDX55_SLAVE_TCU, SDX55_SLAVE_CLK_CTL, SDX55_SLAVE_IMEM_CFG);
 DEFINE_QNODE(xm_sdc1, SDX55_MASTER_SDCC_1, 1, 8, SDX55_SLAVE_AOSS, SDX55_SLAVE_IPA_CFG, SDX55_SLAVE_ANOC_SNOC, SDX55_SLAVE_AOP, SDX55_SLAVE_AUDIO);
 DEFINE_QNODE(xm_usb3, SDX55_MASTER_USB3, 1, 8, SDX55_SLAVE_ANOC_SNOC);
-DEFINE_QNODE(ipa_core_slave, SDX55_SLAVE_IPA_CORE, 1, 8);
 DEFINE_QNODE(ebi, SDX55_SLAVE_EBI_CH0, 1, 4);
 DEFINE_QNODE(qns_llcc, SDX55_SLAVE_LLCC, 1, 16, SDX55_SLAVE_EBI_CH0);
 DEFINE_QNODE(qns_memnoc_snoc, SDX55_SLAVE_MEM_NOC_SNOC, 1, 8, SDX55_MASTER_MEM_NOC_SNOC);
@@ -82,7 +80,6 @@
 DEFINE_QBCM(bcm_mc0, "MC0", true, &ebi);
 DEFINE_QBCM(bcm_sh0, "SH0", true, &qns_llcc);
 DEFINE_QBCM(bcm_ce0, "CE0", false, &qxm_crypto);
-DEFINE_QBCM(bcm_ip0, "IP0", false, &ipa_core_slave);
 DEFINE_QBCM(bcm_pn0, "PN0", false, &qhm_snoc_cfg);
 DEFINE_QBCM(bcm_sh3, "SH3", false, &xm_apps_rdwr);
 DEFINE_QBCM(bcm_sh4, "SH4", false, &qns_memnoc_snoc, &qns_sys_pcie);
@@ -219,22 +216,6 @@
 	.num_bcms = ARRAY_SIZE(system_noc_bcms),
 };
 
-static struct qcom_icc_bcm *ipa_virt_bcms[] = {
-	&bcm_ip0,
-};
-
-static struct qcom_icc_node *ipa_virt_nodes[] = {
-	[MASTER_IPA_CORE] = &ipa_core_master,
-	[SLAVE_IPA_CORE] = &ipa_core_slave,
-};
-
-static const struct qcom_icc_desc sdx55_ipa_virt = {
-	.nodes = ipa_virt_nodes,
-	.num_nodes = ARRAY_SIZE(ipa_virt_nodes),
-	.bcms = ipa_virt_bcms,
-	.num_bcms = ARRAY_SIZE(ipa_virt_bcms),
-};
-
 static const struct of_device_id qnoc_of_match[] = {
 	{ .compatible = "qcom,sdx55-mc-virt",
 	  .data = &sdx55_mc_virt},
@@ -242,8 +223,6 @@
 	  .data = &sdx55_mem_noc},
 	{ .compatible = "qcom,sdx55-system-noc",
 	  .data = &sdx55_system_noc},
-	{ .compatible = "qcom,sdx55-ipa-virt",
-	  .data = &sdx55_ipa_virt},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, qnoc_of_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/sm8150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/sm8150.c
@@ -535,7 +535,6 @@
 	.driver = {
 		.name = "qnoc-sm8150",
 		.of_match_table = qnoc_of_match,
-		.sync_state = icc_sync_state,
 	},
 };
 module_platform_driver(qnoc_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/qcom/sm8350.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/qcom/sm8350.c
@@ -531,7 +531,6 @@
 	.driver = {
 		.name = "qnoc-sm8350",
 		.of_match_table = qnoc_of_match,
-		.sync_state = icc_sync_state,
 	},
 };
 module_platform_driver(qnoc_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/interconnect/samsung/exynos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/interconnect/samsung/exynos.c
@@ -149,6 +149,9 @@
 				 &priv->bus_clk_ratio))
 		priv->bus_clk_ratio = EXYNOS_ICC_DEFAULT_BUS_CLK_RATIO;
 
+	icc_node->data = priv;
+	icc_node_add(icc_node, provider);
+
 	/*
 	 * Register a PM QoS request for the parent (devfreq) device.
 	 */
@@ -157,9 +160,6 @@
 	if (ret < 0)
 		goto err_node_del;
 
-	icc_node->data = priv;
-	icc_node_add(icc_node, provider);
-
 	icc_parent_node = exynos_icc_get_parent(bus_dev->of_node);
 	if (IS_ERR(icc_parent_node)) {
 		ret = PTR_ERR(icc_parent_node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/amd/amd_iommu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/amd/amd_iommu.h
@@ -14,6 +14,7 @@
 extern irqreturn_t amd_iommu_int_thread(int irq, void *data);
 extern irqreturn_t amd_iommu_int_handler(int irq, void *data);
 extern void amd_iommu_apply_erratum_63(u16 devid);
+extern void amd_iommu_restart_event_logging(struct amd_iommu *iommu);
 extern void amd_iommu_reset_cmd_buffer(struct amd_iommu *iommu);
 extern int amd_iommu_init_devices(void);
 extern void amd_iommu_uninit_devices(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/amd/amd_iommu_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/amd/amd_iommu_types.h
@@ -110,6 +110,7 @@
 #define PASID_MASK		0x0000ffff
 
 /* MMIO status bits */
+#define MMIO_STATUS_EVT_OVERFLOW_INT_MASK	(1 << 0)
 #define MMIO_STATUS_EVT_INT_MASK	(1 << 1)
 #define MMIO_STATUS_COM_WAIT_INT_MASK	(1 << 2)
 #define MMIO_STATUS_PPR_INT_MASK	(1 << 6)
@@ -449,6 +450,11 @@
 /* kmem_cache to get tables with 128 byte alignement */
 extern struct kmem_cache *amd_iommu_irq_cache;
 
+/* Make iterating over all pci segment easier */
+#define for_each_pci_segment(pci_seg) \
+	list_for_each_entry((pci_seg), &amd_iommu_pci_seg_list, list)
+#define for_each_pci_segment_safe(pci_seg, next) \
+	list_for_each_entry_safe((pci_seg), (next), &amd_iommu_pci_seg_list, list)
 /*
  * Make iterating over all IOMMUs easier
  */
@@ -524,6 +530,17 @@
 };
 
 /*
+ * This structure contains information about one PCI segment in the system.
+ */
+struct amd_iommu_pci_seg {
+	/* List with all PCI segments in the system */
+	struct list_head list;
+
+	/* PCI segment number */
+	u16 id;
+};
+
+/*
  * Structure where we save information about one hardware AMD IOMMU in the
  * system.
  */
@@ -574,7 +591,7 @@
 	u16 cap_ptr;
 
 	/* pci domain of this IOMMU */
-	u16 pci_seg;
+	struct amd_iommu_pci_seg *pci_seg;
 
 	/* start of exclusion range of that IOMMU */
 	u64 exclusion_start;
@@ -643,8 +660,6 @@
 	/* DebugFS Info */
 	struct dentry *debugfs;
 #endif
-	/* IRQ notifier for IntCapXT interrupt */
-	struct irq_affinity_notify intcapxt_notify;
 };
 
 static inline struct amd_iommu *dev_to_amd_iommu(struct device *dev)
@@ -705,6 +720,12 @@
 extern struct list_head acpihid_map;
 
 /*
+ * List with all PCI segments in the system. This list is not locked because
+ * it is only written at driver initialization time
+ */
+extern struct list_head amd_iommu_pci_seg_list;
+
+/*
  * List with all IOMMUs in the system. This list is not locked because it is
  * only written and read at driver initialization or suspend time
  */
@@ -919,8 +940,8 @@
 	 */
 	struct irq_cfg *cfg;
 	int ga_vector;
-	int ga_root_ptr;
-	int ga_tag;
+	u64 ga_root_ptr;
+	u32 ga_tag;
 };
 
 struct amd_irte_ops {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/amd/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/amd/init.c
@@ -21,6 +21,7 @@
 #include <linux/export.h>
 #include <linux/kmemleak.h>
 #include <linux/mem_encrypt.h>
+#include <linux/iopoll.h>
 #include <asm/pci-direct.h>
 #include <asm/iommu.h>
 #include <asm/apic.h>
@@ -83,7 +84,11 @@
 #define ACPI_DEVFLAG_LINT1              0x80
 #define ACPI_DEVFLAG_ATSDIS             0x10000000
 
-#define LOOP_TIMEOUT	100000
+#define LOOP_TIMEOUT	2000000
+
+#define IVRS_GET_SBDF_ID(seg, bus, dev, fd)	(((seg & 0xffff) << 16) | ((bus & 0xff) << 8) \
+						 | ((dev & 0x1f) << 3) | (fn & 0x7))
+
 /*
  * ACPI table definitions
  *
@@ -162,6 +167,7 @@
 LIST_HEAD(amd_iommu_unity_map);		/* a list of required unity mappings
 					   we find in ACPI */
 
+LIST_HEAD(amd_iommu_pci_seg_list);	/* list of all PCI segments */
 LIST_HEAD(amd_iommu_list);		/* list of all AMD IOMMUs in the
 					   system */
 
@@ -655,6 +661,16 @@
 }
 
 /*
+ * This function restarts event logging in case the IOMMU experienced
+ * an event log buffer overflow.
+ */
+void amd_iommu_restart_event_logging(struct amd_iommu *iommu)
+{
+	iommu_feature_disable(iommu, CONTROL_EVT_LOG_EN);
+	iommu_feature_enable(iommu, CONTROL_EVT_LOG_EN);
+}
+
+/*
  * This function resets the command buffer if the IOMMU stopped fetching
  * commands from it.
  */
@@ -800,19 +816,25 @@
 #endif
 }
 
+#ifdef CONFIG_IRQ_REMAP
 static int iommu_ga_log_enable(struct amd_iommu *iommu)
 {
-#ifdef CONFIG_IRQ_REMAP
 	u32 status, i;
+	u64 entry;
 
 	if (!iommu->ga_log)
 		return -EINVAL;
 
-	status = readl(iommu->mmio_base + MMIO_STATUS_OFFSET);
+	entry = iommu_virt_to_phys(iommu->ga_log) | GA_LOG_SIZE_512;
+	memcpy_toio(iommu->mmio_base + MMIO_GA_LOG_BASE_OFFSET,
+		    &entry, sizeof(entry));
+	entry = (iommu_virt_to_phys(iommu->ga_log_tail) &
+		 (BIT_ULL(52)-1)) & ~7ULL;
+	memcpy_toio(iommu->mmio_base + MMIO_GA_LOG_TAIL_OFFSET,
+		    &entry, sizeof(entry));
+	writel(0x00, iommu->mmio_base + MMIO_GA_HEAD_OFFSET);
+	writel(0x00, iommu->mmio_base + MMIO_GA_TAIL_OFFSET);
 
-	/* Check if already running */
-	if (status & (MMIO_STATUS_GALOG_RUN_MASK))
-		return 0;
 
 	iommu_feature_enable(iommu, CONTROL_GAINT_EN);
 	iommu_feature_enable(iommu, CONTROL_GALOG_EN);
@@ -821,19 +843,17 @@
 		status = readl(iommu->mmio_base + MMIO_STATUS_OFFSET);
 		if (status & (MMIO_STATUS_GALOG_RUN_MASK))
 			break;
+		udelay(10);
 	}
 
-	if (i >= LOOP_TIMEOUT)
+	if (WARN_ON(i >= LOOP_TIMEOUT))
 		return -EINVAL;
-#endif /* CONFIG_IRQ_REMAP */
+
 	return 0;
 }
 
 static int iommu_init_ga_log(struct amd_iommu *iommu)
 {
-#ifdef CONFIG_IRQ_REMAP
-	u64 entry;
-
 	if (!AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir))
 		return 0;
 
@@ -847,24 +867,12 @@
 	if (!iommu->ga_log_tail)
 		goto err_out;
 
-	entry = iommu_virt_to_phys(iommu->ga_log) | GA_LOG_SIZE_512;
-	memcpy_toio(iommu->mmio_base + MMIO_GA_LOG_BASE_OFFSET,
-		    &entry, sizeof(entry));
-	entry = (iommu_virt_to_phys(iommu->ga_log_tail) &
-		 (BIT_ULL(52)-1)) & ~7ULL;
-	memcpy_toio(iommu->mmio_base + MMIO_GA_LOG_TAIL_OFFSET,
-		    &entry, sizeof(entry));
-	writel(0x00, iommu->mmio_base + MMIO_GA_HEAD_OFFSET);
-	writel(0x00, iommu->mmio_base + MMIO_GA_TAIL_OFFSET);
-
 	return 0;
 err_out:
 	free_ga_log(iommu);
 	return -EINVAL;
-#else
-	return 0;
-#endif /* CONFIG_IRQ_REMAP */
 }
+#endif /* CONFIG_IRQ_REMAP */
 
 static int __init alloc_cwwb_sem(struct amd_iommu *iommu)
 {
@@ -1440,8 +1448,54 @@
 	return 0;
 }
 
+/* Allocate PCI segment data structure */
+static struct amd_iommu_pci_seg *__init alloc_pci_segment(u16 id)
+{
+	struct amd_iommu_pci_seg *pci_seg;
+
+	pci_seg = kzalloc(sizeof(struct amd_iommu_pci_seg), GFP_KERNEL);
+	if (pci_seg == NULL)
+		return NULL;
+
+	pci_seg->id = id;
+	list_add_tail(&pci_seg->list, &amd_iommu_pci_seg_list);
+
+	return pci_seg;
+}
+
+static struct amd_iommu_pci_seg *__init get_pci_segment(u16 id)
+{
+	struct amd_iommu_pci_seg *pci_seg;
+
+	for_each_pci_segment(pci_seg) {
+		if (pci_seg->id == id)
+			return pci_seg;
+	}
+
+	return alloc_pci_segment(id);
+}
+
+static void __init free_pci_segments(void)
+{
+	struct amd_iommu_pci_seg *pci_seg, *next;
+
+	for_each_pci_segment_safe(pci_seg, next) {
+		list_del(&pci_seg->list);
+		kfree(pci_seg);
+	}
+}
+
+static void __init free_sysfs(struct amd_iommu *iommu)
+{
+	if (iommu->iommu.dev) {
+		iommu_device_unregister(&iommu->iommu);
+		iommu_device_sysfs_remove(&iommu->iommu);
+	}
+}
+
 static void __init free_iommu_one(struct amd_iommu *iommu)
 {
+	free_sysfs(iommu);
 	free_cwwb_sem(iommu);
 	free_command_buffer(iommu);
 	free_event_buffer(iommu);
@@ -1526,8 +1580,14 @@
  */
 static int __init init_iommu_one(struct amd_iommu *iommu, struct ivhd_header *h)
 {
+	struct amd_iommu_pci_seg *pci_seg;
 	int ret;
 
+	pci_seg = get_pci_segment(h->pci_seg);
+	if (pci_seg == NULL)
+		return -ENOMEM;
+	iommu->pci_seg = pci_seg;
+
 	raw_spin_lock_init(&iommu->lock);
 	iommu->cmd_sem_val = 0;
 
@@ -1548,7 +1608,6 @@
 	 */
 	iommu->devid   = h->devid;
 	iommu->cap_ptr = h->cap_ptr;
-	iommu->pci_seg = h->pci_seg;
 	iommu->mmio_phys = h->mmio_phys;
 
 	switch (h->type) {
@@ -1806,6 +1865,9 @@
 	/* Prevent binding other PCI device drivers to IOMMU devices */
 	iommu->dev->match_driver = false;
 
+	/* ACPI _PRT won't have an IRQ for IOMMU */
+	iommu->dev->irq_managed = 1;
+
 	pci_read_config_dword(iommu->dev, cap_ptr + MMIO_CAP_HDR_OFFSET,
 			      &iommu->cap);
 
@@ -1845,10 +1907,6 @@
 	if (iommu_feature(iommu, FEATURE_PPR) && alloc_ppr_log(iommu))
 		return -ENOMEM;
 
-	ret = iommu_init_ga_log(iommu);
-	if (ret)
-		return ret;
-
 	if (iommu->cap & (1UL << IOMMU_CAP_NPCACHE)) {
 		pr_info("Using strict mode due to virtualization\n");
 		iommu_set_dma_strict();
@@ -1925,8 +1983,6 @@
 	}
 	if (irq_remapping_enabled) {
 		pr_info("Interrupt remapping enabled\n");
-		if (AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir))
-			pr_info("Virtual APIC enabled\n");
 		if (amd_iommu_xt_mode == IRQ_REMAP_X2APIC_MODE)
 			pr_info("X2APIC enabled\n");
 	}
@@ -2013,48 +2069,18 @@
 	};
 } __attribute__ ((packed));
 
-/*
- * There isn't really any need to mask/unmask at the irqchip level because
- * the 64-bit INTCAPXT registers can be updated atomically without tearing
- * when the affinity is being updated.
- */
-static void intcapxt_unmask_irq(struct irq_data *data)
-{
-}
-
-static void intcapxt_mask_irq(struct irq_data *data)
-{
-}
 
 static struct irq_chip intcapxt_controller;
 
 static int intcapxt_irqdomain_activate(struct irq_domain *domain,
 				       struct irq_data *irqd, bool reserve)
 {
-	struct amd_iommu *iommu = irqd->chip_data;
-	struct irq_cfg *cfg = irqd_cfg(irqd);
-	union intcapxt xt;
-
-	xt.capxt = 0ULL;
-	xt.dest_mode_logical = apic->dest_mode_logical;
-	xt.vector = cfg->vector;
-	xt.destid_0_23 = cfg->dest_apicid & GENMASK(23, 0);
-	xt.destid_24_31 = cfg->dest_apicid >> 24;
-
-	/**
-	 * Current IOMMU implemtation uses the same IRQ for all
-	 * 3 IOMMU interrupts.
-	 */
-	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_EVT_OFFSET);
-	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_PPR_OFFSET);
-	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_GALOG_OFFSET);
 	return 0;
 }
 
 static void intcapxt_irqdomain_deactivate(struct irq_domain *domain,
 					  struct irq_data *irqd)
 {
-	intcapxt_mask_irq(irqd);
 }
 
 
@@ -2088,6 +2114,38 @@
 	irq_domain_free_irqs_top(domain, virq, nr_irqs);
 }
 
+
+static void intcapxt_unmask_irq(struct irq_data *irqd)
+{
+	struct amd_iommu *iommu = irqd->chip_data;
+	struct irq_cfg *cfg = irqd_cfg(irqd);
+	union intcapxt xt;
+
+	xt.capxt = 0ULL;
+	xt.dest_mode_logical = apic->dest_mode_logical;
+	xt.vector = cfg->vector;
+	xt.destid_0_23 = cfg->dest_apicid & GENMASK(23, 0);
+	xt.destid_24_31 = cfg->dest_apicid >> 24;
+
+	/**
+	 * Current IOMMU implementation uses the same IRQ for all
+	 * 3 IOMMU interrupts.
+	 */
+	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_EVT_OFFSET);
+	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_PPR_OFFSET);
+	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_GALOG_OFFSET);
+}
+
+static void intcapxt_mask_irq(struct irq_data *irqd)
+{
+	struct amd_iommu *iommu = irqd->chip_data;
+
+	writeq(0, iommu->mmio_base + MMIO_INTCAPXT_EVT_OFFSET);
+	writeq(0, iommu->mmio_base + MMIO_INTCAPXT_PPR_OFFSET);
+	writeq(0, iommu->mmio_base + MMIO_INTCAPXT_GALOG_OFFSET);
+}
+
+
 static int intcapxt_set_affinity(struct irq_data *irqd,
 				 const struct cpumask *mask, bool force)
 {
@@ -2097,8 +2155,12 @@
 	ret = parent->chip->irq_set_affinity(parent, mask, force);
 	if (ret < 0 || ret == IRQ_SET_MASK_OK_DONE)
 		return ret;
+	return 0;
+}
 
-	return intcapxt_irqdomain_activate(irqd->domain, irqd, false);
+static int intcapxt_set_wake(struct irq_data *irqd, unsigned int on)
+{
+	return on ? -EOPNOTSUPP : 0;
 }
 
 static struct irq_chip intcapxt_controller = {
@@ -2108,7 +2170,8 @@
 	.irq_ack		= irq_chip_ack_parent,
 	.irq_retrigger		= irq_chip_retrigger_hierarchy,
 	.irq_set_affinity       = intcapxt_set_affinity,
-	.flags			= IRQCHIP_SKIP_SET_WAKE,
+	.irq_set_wake		= intcapxt_set_wake,
+	.flags			= IRQCHIP_MASK_ON_SUSPEND,
 };
 
 static const struct irq_domain_ops intcapxt_domain_ops = {
@@ -2170,7 +2233,6 @@
 		return ret;
 	}
 
-	iommu_feature_enable(iommu, CONTROL_INTCAPXT_EN);
 	return 0;
 }
 
@@ -2193,13 +2255,14 @@
 
 	iommu->int_enabled = true;
 enable_faults:
+
+	if (amd_iommu_xt_mode == IRQ_REMAP_X2APIC_MODE)
+		iommu_feature_enable(iommu, CONTROL_INTCAPXT_EN);
+
 	iommu_feature_enable(iommu, CONTROL_EVT_INT_EN);
 
 	if (iommu->ppr_log != NULL)
 		iommu_feature_enable(iommu, CONTROL_PPRINT_EN);
-
-	iommu_ga_log_enable(iommu);
-
 	return 0;
 }
 
@@ -2405,8 +2468,6 @@
 #ifdef CONFIG_IRQ_REMAP
 	switch (amd_iommu_guest_ir) {
 	case AMD_IOMMU_GUEST_IR_VAPIC:
-		iommu_feature_enable(iommu, CONTROL_GAM_EN);
-		fallthrough;
 	case AMD_IOMMU_GUEST_IR_LEGACY_GA:
 		iommu_feature_enable(iommu, CONTROL_GA_EN);
 		iommu->irte_ops = &irte_128_ops;
@@ -2477,19 +2538,6 @@
 			iommu_flush_all_caches(iommu);
 		}
 	}
-
-#ifdef CONFIG_IRQ_REMAP
-	/*
-	 * Note: We have already checked GASup from IVRS table.
-	 *       Now, we need to make sure that GAMSup is set.
-	 */
-	if (AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir) &&
-	    !check_feature_on_all_iommus(FEATURE_GAM_VAPIC))
-		amd_iommu_guest_ir = AMD_IOMMU_GUEST_IR_LEGACY_GA;
-
-	if (AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir))
-		amd_iommu_irq_ops.capability |= (1 << IRQ_POSTING_CAP);
-#endif
 }
 
 static void enable_iommus_v2(void)
@@ -2502,10 +2550,64 @@
 	}
 }
 
+static void enable_iommus_vapic(void)
+{
+#ifdef CONFIG_IRQ_REMAP
+	u32 status, i;
+	struct amd_iommu *iommu;
+
+	for_each_iommu(iommu) {
+		/*
+		 * Disable GALog if already running. It could have been enabled
+		 * in the previous boot before kdump.
+		 */
+		status = readl(iommu->mmio_base + MMIO_STATUS_OFFSET);
+		if (!(status & MMIO_STATUS_GALOG_RUN_MASK))
+			continue;
+
+		iommu_feature_disable(iommu, CONTROL_GALOG_EN);
+		iommu_feature_disable(iommu, CONTROL_GAINT_EN);
+
+		/*
+		 * Need to set and poll check the GALOGRun bit to zero before
+		 * we can set/ modify GA Log registers safely.
+		 */
+		for (i = 0; i < LOOP_TIMEOUT; ++i) {
+			status = readl(iommu->mmio_base + MMIO_STATUS_OFFSET);
+			if (!(status & MMIO_STATUS_GALOG_RUN_MASK))
+				break;
+			udelay(10);
+		}
+
+		if (WARN_ON(i >= LOOP_TIMEOUT))
+			return;
+	}
+
+	if (AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir) &&
+	    !check_feature_on_all_iommus(FEATURE_GAM_VAPIC)) {
+		amd_iommu_guest_ir = AMD_IOMMU_GUEST_IR_LEGACY_GA;
+		return;
+	}
+
+	/* Enabling GAM support */
+	for_each_iommu(iommu) {
+		if (iommu_init_ga_log(iommu) ||
+		    iommu_ga_log_enable(iommu))
+			return;
+
+		iommu_feature_enable(iommu, CONTROL_GAM_EN);
+	}
+
+	amd_iommu_irq_ops.capability |= (1 << IRQ_POSTING_CAP);
+	pr_info("Virtual APIC enabled\n");
+#endif
+}
+
+
 static void enable_iommus(void)
 {
 	early_enable_iommus();
-
+	enable_iommus_vapic();
 	enable_iommus_v2();
 }
 
@@ -2576,6 +2678,7 @@
 	amd_iommu_dev_table = NULL;
 
 	free_iommu_all();
+	free_pci_segments();
 }
 
 /* SB IOAPIC is always on this device in AMD systems */
@@ -2902,6 +3005,7 @@
 		register_syscore_ops(&amd_iommu_syscore_ops);
 		ret = amd_iommu_init_pci();
 		init_state = ret ? IOMMU_INIT_ERROR : IOMMU_PCI_INIT;
+		enable_iommus_vapic();
 		enable_iommus_v2();
 		break;
 	case IOMMU_PCI_INIT:
@@ -3125,24 +3229,32 @@
 
 static int __init parse_ivrs_ioapic(char *str)
 {
-	unsigned int bus, dev, fn;
-	int ret, id, i;
-	u16 devid;
-
-	ret = sscanf(str, "[%d]=%x:%x.%x", &id, &bus, &dev, &fn);
+	u32 seg = 0, bus, dev, fn;
+	int id, i;
+	u32 devid;
 
-	if (ret != 4) {
-		pr_err("Invalid command line: ivrs_ioapic%s\n", str);
-		return 1;
+	if (sscanf(str, "=%d@%x:%x.%x", &id, &bus, &dev, &fn) == 4 ||
+	    sscanf(str, "=%d@%x:%x:%x.%x", &id, &seg, &bus, &dev, &fn) == 5)
+		goto found;
+
+	if (sscanf(str, "[%d]=%x:%x.%x", &id, &bus, &dev, &fn) == 4 ||
+	    sscanf(str, "[%d]=%x:%x:%x.%x", &id, &seg, &bus, &dev, &fn) == 5) {
+		pr_warn("ivrs_ioapic%s option format deprecated; use ivrs_ioapic=%d@%04x:%02x:%02x.%d instead\n",
+			str, id, seg, bus, dev, fn);
+		goto found;
 	}
 
+	pr_err("Invalid command line: ivrs_ioapic%s\n", str);
+	return 1;
+
+found:
 	if (early_ioapic_map_size == EARLY_MAP_SIZE) {
 		pr_err("Early IOAPIC map overflow - ignoring ivrs_ioapic%s\n",
 			str);
 		return 1;
 	}
 
-	devid = ((bus & 0xff) << 8) | ((dev & 0x1f) << 3) | (fn & 0x7);
+	devid = IVRS_GET_SBDF_ID(seg, bus, dev, fn);
 
 	cmdline_maps			= true;
 	i				= early_ioapic_map_size++;
@@ -3155,24 +3267,32 @@
 
 static int __init parse_ivrs_hpet(char *str)
 {
-	unsigned int bus, dev, fn;
-	int ret, id, i;
-	u16 devid;
-
-	ret = sscanf(str, "[%d]=%x:%x.%x", &id, &bus, &dev, &fn);
+	u32 seg = 0, bus, dev, fn;
+	int id, i;
+	u32 devid;
 
-	if (ret != 4) {
-		pr_err("Invalid command line: ivrs_hpet%s\n", str);
-		return 1;
+	if (sscanf(str, "=%d@%x:%x.%x", &id, &bus, &dev, &fn) == 4 ||
+	    sscanf(str, "=%d@%x:%x:%x.%x", &id, &seg, &bus, &dev, &fn) == 5)
+		goto found;
+
+	if (sscanf(str, "[%d]=%x:%x.%x", &id, &bus, &dev, &fn) == 4 ||
+	    sscanf(str, "[%d]=%x:%x:%x.%x", &id, &seg, &bus, &dev, &fn) == 5) {
+		pr_warn("ivrs_hpet%s option format deprecated; use ivrs_hpet=%d@%04x:%02x:%02x.%d instead\n",
+			str, id, seg, bus, dev, fn);
+		goto found;
 	}
 
+	pr_err("Invalid command line: ivrs_hpet%s\n", str);
+	return 1;
+
+found:
 	if (early_hpet_map_size == EARLY_MAP_SIZE) {
 		pr_err("Early HPET map overflow - ignoring ivrs_hpet%s\n",
 			str);
 		return 1;
 	}
 
-	devid = ((bus & 0xff) << 8) | ((dev & 0x1f) << 3) | (fn & 0x7);
+	devid = IVRS_GET_SBDF_ID(seg, bus, dev, fn);
 
 	cmdline_maps			= true;
 	i				= early_hpet_map_size++;
@@ -3183,19 +3303,53 @@
 	return 1;
 }
 
+#define ACPIID_LEN (ACPIHID_UID_LEN + ACPIHID_HID_LEN)
+
 static int __init parse_ivrs_acpihid(char *str)
 {
-	u32 bus, dev, fn;
-	char *hid, *uid, *p;
-	char acpiid[ACPIHID_UID_LEN + ACPIHID_HID_LEN] = {0};
-	int ret, i;
-
-	ret = sscanf(str, "[%x:%x.%x]=%s", &bus, &dev, &fn, acpiid);
-	if (ret != 4) {
-		pr_err("Invalid command line: ivrs_acpihid(%s)\n", str);
-		return 1;
+	u32 seg = 0, bus, dev, fn;
+	char *hid, *uid, *p, *addr;
+	char acpiid[ACPIID_LEN] = {0};
+	int i;
+
+	addr = strchr(str, '@');
+	if (!addr) {
+		addr = strchr(str, '=');
+		if (!addr)
+			goto not_found;
+
+		++addr;
+
+		if (strlen(addr) > ACPIID_LEN)
+			goto not_found;
+
+		if (sscanf(str, "[%x:%x.%x]=%s", &bus, &dev, &fn, acpiid) == 4 ||
+		    sscanf(str, "[%x:%x:%x.%x]=%s", &seg, &bus, &dev, &fn, acpiid) == 5) {
+			pr_warn("ivrs_acpihid%s option format deprecated; use ivrs_acpihid=%s@%04x:%02x:%02x.%d instead\n",
+				str, acpiid, seg, bus, dev, fn);
+			goto found;
+		}
+		goto not_found;
 	}
 
+	/* We have the '@', make it the terminator to get just the acpiid */
+	*addr++ = 0;
+
+	if (strlen(str) > ACPIID_LEN + 1)
+		goto not_found;
+
+	if (sscanf(str, "=%s", acpiid) != 1)
+		goto not_found;
+
+	if (sscanf(addr, "%x:%x.%x", &bus, &dev, &fn) == 3 ||
+	    sscanf(addr, "%x:%x:%x.%x", &seg, &bus, &dev, &fn) == 4)
+		goto found;
+
+not_found:
+	pr_err("Invalid command line: ivrs_acpihid%s\n", str);
+	return 1;
+
+found:
 	p = acpiid;
 	hid = strsep(&p, ":");
 	uid = p;
@@ -3205,11 +3359,17 @@
 		return 1;
 	}
 
+	/*
+	 * Ignore leading zeroes after ':', so e.g., AMDI0095:00
+	 * will match AMDI0095:0 in the second strcmp in acpi_dev_hid_uid_match
+	 */
+	while (*uid == '0' && *(uid + 1))
+		uid++;
+
 	i = early_acpihid_map_size++;
 	memcpy(early_acpihid_map[i].hid, hid, strlen(hid));
 	memcpy(early_acpihid_map[i].uid, uid, strlen(uid));
-	early_acpihid_map[i].devid =
-		((bus & 0xff) << 8) | ((dev & 0x1f) << 3) | (fn & 0x7);
+	early_acpihid_map[i].devid = IVRS_GET_SBDF_ID(seg, bus, dev, fn);
 	early_acpihid_map[i].cmd_line	= true;
 
 	return 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/amd/io_pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/amd/io_pgtable.c
@@ -519,12 +519,6 @@
 
 	dom = container_of(pgtable, struct protection_domain, iop);
 
-	/* Update data structure */
-	amd_iommu_domain_clr_pt_root(dom);
-
-	/* Make changes visible to IOMMUs */
-	amd_iommu_domain_update(dom);
-
 	/* Page-table is not visible to IOMMU anymore, so free it */
 	BUG_ON(pgtable->mode < PAGE_MODE_NONE ||
 	       pgtable->mode > PAGE_MODE_6_LEVEL);
@@ -532,6 +526,12 @@
 	root = (unsigned long)pgtable->root;
 	freelist = free_sub_pt(root, pgtable->mode, freelist);
 
+	/* Update data structure */
+	amd_iommu_domain_clr_pt_root(dom);
+
+	/* Make changes visible to IOMMUs */
+	amd_iommu_domain_update(dom);
+
 	free_page_list(freelist);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/amd/iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/amd/iommu.c
@@ -742,7 +742,8 @@
 #endif /* !CONFIG_IRQ_REMAP */
 
 #define AMD_IOMMU_INT_MASK	\
-	(MMIO_STATUS_EVT_INT_MASK | \
+	(MMIO_STATUS_EVT_OVERFLOW_INT_MASK | \
+	 MMIO_STATUS_EVT_INT_MASK | \
 	 MMIO_STATUS_PPR_INT_MASK | \
 	 MMIO_STATUS_GALOG_INT_MASK)
 
@@ -752,7 +753,7 @@
 	u32 status = readl(iommu->mmio_base + MMIO_STATUS_OFFSET);
 
 	while (status & AMD_IOMMU_INT_MASK) {
-		/* Enable EVT and PPR and GA interrupts again */
+		/* Enable interrupt sources again */
 		writel(AMD_IOMMU_INT_MASK,
 			iommu->mmio_base + MMIO_STATUS_OFFSET);
 
@@ -773,6 +774,11 @@
 		}
 #endif
 
+		if (status & MMIO_STATUS_EVT_OVERFLOW_INT_MASK) {
+			pr_info_ratelimited("IOMMU event log overflow\n");
+			amd_iommu_restart_event_logging(iommu);
+		}
+
 		/*
 		 * Hardware bug: ERBT1312
 		 * When re-enabling interrupt (by writing 1
@@ -846,7 +852,8 @@
 	memset(cmd, 0, sizeof(*cmd));
 	cmd->data[0] = lower_32_bits(paddr) | CMD_COMPL_WAIT_STORE_MASK;
 	cmd->data[1] = upper_32_bits(paddr);
-	cmd->data[2] = data;
+	cmd->data[2] = lower_32_bits(data);
+	cmd->data[3] = upper_32_bits(data);
 	CMD_SET_TYPE(cmd, CMD_COMPL_WAIT);
 }
 
@@ -1579,27 +1586,29 @@
 	/* Only allow access to user-accessible pages */
 	ret = pci_enable_pasid(pdev, 0);
 	if (ret)
-		goto out_err;
+		return ret;
 
 	/* First reset the PRI state of the device */
 	ret = pci_reset_pri(pdev);
 	if (ret)
-		goto out_err;
+		goto out_err_pasid;
 
 	/* Enable PRI */
 	/* FIXME: Hardcode number of outstanding requests for now */
 	ret = pci_enable_pri(pdev, 32);
 	if (ret)
-		goto out_err;
+		goto out_err_pasid;
 
 	ret = pci_enable_ats(pdev, PAGE_SHIFT);
 	if (ret)
-		goto out_err;
+		goto out_err_pri;
 
 	return 0;
 
-out_err:
+out_err_pri:
 	pci_disable_pri(pdev);
+
+out_err_pasid:
 	pci_disable_pasid(pdev);
 
 	return ret;
@@ -1810,17 +1819,10 @@
 	amd_iommu_domain_flush_complete(domain);
 }
 
-static void __init amd_iommu_init_dma_ops(void)
-{
-	swiotlb = (iommu_default_passthrough() || sme_me_mask) ? 1 : 0;
-}
-
 int __init amd_iommu_init_api(void)
 {
 	int err;
 
-	amd_iommu_init_dma_ops();
-
 	err = bus_set_iommu(&pci_bus_type, &amd_iommu_ops);
 	if (err)
 		return err;
@@ -2220,7 +2222,7 @@
 	unsigned long flags;
 
 	spin_lock_irqsave(&dom->lock, flags);
-	domain_flush_pages(dom, gather->start, gather->end - gather->start, 1);
+	domain_flush_pages(dom, gather->start, gather->end - gather->start + 1, 1);
 	amd_iommu_domain_flush_complete(dom);
 	spin_unlock_irqrestore(&dom->lock, flags);
 }
@@ -3314,8 +3316,7 @@
 	struct irte_ga *entry = (struct irte_ga *) ir_data->entry;
 	u64 valid;
 
-	if (!AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir) ||
-	    !entry || entry->lo.fields_vapic.guest_mode)
+	if (!AMD_IOMMU_GUEST_IR_VAPIC(amd_iommu_guest_ir) || !entry)
 		return 0;
 
 	valid = entry->lo.fields_vapic.valid;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/amd/iommu_v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/amd/iommu_v2.c
@@ -264,8 +264,8 @@
 
 static void put_pasid_state_wait(struct pasid_state *pasid_state)
 {
-	refcount_dec(&pasid_state->count);
-	wait_event(pasid_state->wq, !refcount_read(&pasid_state->count));
+	if (!refcount_dec_and_test(&pasid_state->count))
+		wait_event(pasid_state->wq, !refcount_read(&pasid_state->count));
 	free_pasid_state(pasid_state);
 }
 
@@ -588,6 +588,7 @@
 	put_device_state(dev_state);
 
 out:
+	pci_dev_put(pdev);
 	return ret;
 }
 
@@ -928,10 +929,8 @@
 {
 	int ret;
 
-	pr_info("AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>\n");
-
 	if (!amd_iommu_v2_supported()) {
-		pr_info("AMD IOMMUv2 functionality not available on this system\n");
+		pr_info("AMD IOMMUv2 functionality not available on this system - This is not a bug.\n");
 		/*
 		 * Load anyway to provide the symbols to other modules
 		 * which may use AMD IOMMUv2 optionally.
@@ -946,6 +945,8 @@
 
 	amd_iommu_register_ppr_notifier(&ppr_nb);
 
+	pr_info("AMD IOMMUv2 loaded and initialized\n");
+
 	return 0;
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/apple-dart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/apple-dart.c
@@ -70,6 +70,8 @@
 #define DART_ERROR_ADDR_HI 0x54
 #define DART_ERROR_ADDR_LO 0x50
 
+#define DART_STREAMS_ENABLE 0xfc
+
 #define DART_TCR(sid) (0x100 + 4 * (sid))
 #define DART_TCR_TRANSLATE_ENABLE BIT(7)
 #define DART_TCR_BYPASS0_ENABLE BIT(8)
@@ -301,6 +303,9 @@
 	apple_dart_hw_disable_dma(&stream_map);
 	apple_dart_hw_clear_all_ttbrs(&stream_map);
 
+	/* enable all streams globally since TCR is used to control isolation */
+	writel(DART_STREAM_ALL, dart->regs + DART_STREAMS_ENABLE);
+
 	/* clear any pending errors before the interrupt is unmasked */
 	writel(readl(dart->regs + DART_ERROR), dart->regs + DART_ERROR);
 
@@ -752,6 +757,7 @@
 	.of_xlate = apple_dart_of_xlate,
 	.def_domain_type = apple_dart_def_domain_type,
 	.pgsize_bitmap = -1UL, /* Restricted during dart probe */
+	.owner = THIS_MODULE,
 };
 
 static irqreturn_t apple_dart_irq(int irq, void *dev)
@@ -827,16 +833,15 @@
 	dart->dev = dev;
 	spin_lock_init(&dart->lock);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	dart->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(dart->regs))
+		return PTR_ERR(dart->regs);
+
 	if (resource_size(res) < 0x4000) {
 		dev_err(dev, "MMIO region too small (%pr)\n", res);
 		return -EINVAL;
 	}
 
-	dart->regs = devm_ioremap_resource(dev, res);
-	if (IS_ERR(dart->regs))
-		return PTR_ERR(dart->regs);
-
 	dart->irq = platform_get_irq(pdev, 0);
 	if (dart->irq < 0)
 		return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3-sva.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3-sva.c
@@ -6,6 +6,7 @@
 #include <linux/mm.h>
 #include <linux/mmu_context.h>
 #include <linux/mmu_notifier.h>
+#include <linux/sched/mm.h>
 #include <linux/slab.h>
 
 #include "arm-smmu-v3.h"
@@ -96,9 +97,14 @@
 	struct arm_smmu_ctx_desc *cd;
 	struct arm_smmu_ctx_desc *ret = NULL;
 
+	/* Don't free the mm until we release the ASID */
+	mmgrab(mm);
+
 	asid = arm64_mm_context_get(mm);
-	if (!asid)
-		return ERR_PTR(-ESRCH);
+	if (!asid) {
+		err = -ESRCH;
+		goto out_drop_mm;
+	}
 
 	cd = kzalloc(sizeof(*cd), GFP_KERNEL);
 	if (!cd) {
@@ -165,6 +171,8 @@
 	kfree(cd);
 out_put_context:
 	arm64_mm_context_put(mm);
+out_drop_mm:
+	mmdrop(mm);
 	return err < 0 ? ERR_PTR(err) : ret;
 }
 
@@ -173,21 +181,50 @@
 	if (arm_smmu_free_asid(cd)) {
 		/* Unpin ASID */
 		arm64_mm_context_put(cd->mm);
+		mmdrop(cd->mm);
 		kfree(cd);
 	}
 }
 
+/*
+ * Cloned from the MAX_TLBI_OPS in arch/arm64/include/asm/tlbflush.h, this
+ * is used as a threshold to replace per-page TLBI commands to issue in the
+ * command queue with an address-space TLBI command, when SMMU w/o a range
+ * invalidation feature handles too many per-page TLBI commands, which will
+ * otherwise result in a soft lockup.
+ */
+#define CMDQ_MAX_TLBI_OPS		(1 << (PAGE_SHIFT - 3))
+
 static void arm_smmu_mm_invalidate_range(struct mmu_notifier *mn,
 					 struct mm_struct *mm,
 					 unsigned long start, unsigned long end)
 {
 	struct arm_smmu_mmu_notifier *smmu_mn = mn_to_smmu(mn);
 	struct arm_smmu_domain *smmu_domain = smmu_mn->domain;
-	size_t size = end - start + 1;
+	size_t size;
+
+	/*
+	 * The mm_types defines vm_end as the first byte after the end address,
+	 * different from IOMMU subsystem using the last address of an address
+	 * range. So do a simple translation here by calculating size correctly.
+	 */
+	size = end - start;
+	if (!(smmu_domain->smmu->features & ARM_SMMU_FEAT_RANGE_INV)) {
+		if (size >= CMDQ_MAX_TLBI_OPS * PAGE_SIZE)
+			size = 0;
+	}
+
+	if (!(smmu_domain->smmu->features & ARM_SMMU_FEAT_BTM)) {
+		if (!size)
+			arm_smmu_tlb_inv_asid(smmu_domain->smmu,
+					      smmu_mn->cd->asid);
+		else
+			arm_smmu_tlb_inv_range_asid(start, size,
+						    smmu_mn->cd->asid,
+						    PAGE_SIZE, false,
+						    smmu_domain);
+	}
 
-	if (!(smmu_domain->smmu->features & ARM_SMMU_FEAT_BTM))
-		arm_smmu_tlb_inv_range_asid(start, size, smmu_mn->cd->asid,
-					    PAGE_SIZE, false, smmu_domain);
 	arm_smmu_atc_inv_domain(smmu_domain, mm->pasid, start, size);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c
@@ -154,6 +154,18 @@
 	q->cons = Q_OVF(q->cons) | Q_WRP(q, cons) | Q_IDX(q, cons);
 }
 
+static void queue_sync_cons_ovf(struct arm_smmu_queue *q)
+{
+	struct arm_smmu_ll_queue *llq = &q->llq;
+
+	if (likely(Q_OVF(llq->prod) == Q_OVF(llq->cons)))
+		return;
+
+	llq->cons = Q_OVF(llq->prod) | Q_WRP(llq, llq->cons) |
+		      Q_IDX(llq, llq->cons);
+	queue_sync_cons_out(q);
+}
+
 static int queue_sync_prod_in(struct arm_smmu_queue *q)
 {
 	u32 prod;
@@ -885,6 +897,12 @@
 				    struct arm_smmu_cmdq_batch *cmds,
 				    struct arm_smmu_cmdq_ent *cmd)
 {
+	if (cmds->num == CMDQ_BATCH_ENTRIES - 1 &&
+	    (smmu->options & ARM_SMMU_OPT_CMDQ_FORCE_SYNC)) {
+		arm_smmu_cmdq_issue_cmdlist(smmu, cmds->cmds, cmds->num, true);
+		cmds->num = 0;
+	}
+
 	if (cmds->num == CMDQ_BATCH_ENTRIES) {
 		arm_smmu_cmdq_issue_cmdlist(smmu, cmds->cmds, cmds->num, false);
 		cmds->num = 0;
@@ -1552,6 +1570,7 @@
 				dev_info(smmu->dev, "\t0x%016llx\n",
 					 (unsigned long long)evt[i]);
 
+			cond_resched();
 		}
 
 		/*
@@ -1563,8 +1582,7 @@
 	} while (!queue_empty(llq));
 
 	/* Sync our overflow flag, as we believe we're up to speed */
-	llq->cons = Q_OVF(llq->prod) | Q_WRP(llq, llq->cons) |
-		    Q_IDX(llq, llq->cons);
+	queue_sync_cons_ovf(q);
 	return IRQ_HANDLED;
 }
 
@@ -1622,9 +1640,7 @@
 	} while (!queue_empty(llq));
 
 	/* Sync our overflow flag, as we believe we're up to speed */
-	llq->cons = Q_OVF(llq->prod) | Q_WRP(llq, llq->cons) |
-		      Q_IDX(llq, llq->cons);
-	queue_sync_cons_out(q);
+	queue_sync_cons_ovf(q);
 	return IRQ_HANDLED;
 }
 
@@ -1865,13 +1881,23 @@
 		/* Get the leaf page size */
 		tg = __ffs(smmu_domain->domain.pgsize_bitmap);
 
+		num_pages = size >> tg;
+
 		/* Convert page size of 12,14,16 (log2) to 1,2,3 */
 		cmd->tlbi.tg = (tg - 10) / 2;
 
-		/* Determine what level the granule is at */
-		cmd->tlbi.ttl = 4 - ((ilog2(granule) - 3) / (tg - 3));
-
-		num_pages = size >> tg;
+		/*
+		 * Determine what level the granule is at. For non-leaf, both
+		 * io-pgtable and SVA pass a nominal last-level granule because
+		 * they don't know what level(s) actually apply, so ignore that
+		 * and leave TTL=0. However for various errata reasons we still
+		 * want to use a range command, so avoid the SVA corner case
+		 * where both scale and num could be 0 as well.
+		 */
+		if (cmd->tlbi.leaf)
+			cmd->tlbi.ttl = 4 - ((ilog2(granule) - 3) / (tg - 3));
+		else if ((num_pages & CMDQ_TLBI_RANGE_NUM_MAX) == 1)
+			num_pages++;
 	}
 
 	cmds.num = 0;
@@ -2831,6 +2857,26 @@
 	}
 }
 
+/*
+ * HiSilicon PCIe tune and trace device can be used to trace TLP headers on the
+ * PCIe link and save the data to memory by DMA. The hardware is restricted to
+ * use identity mapping only.
+ */
+#define IS_HISI_PTT_DEVICE(pdev)	((pdev)->vendor == PCI_VENDOR_ID_HUAWEI && \
+					 (pdev)->device == 0xa12e)
+
+static int arm_smmu_def_domain_type(struct device *dev)
+{
+	if (dev_is_pci(dev)) {
+		struct pci_dev *pdev = to_pci_dev(dev);
+
+		if (IS_HISI_PTT_DEVICE(pdev))
+			return IOMMU_DOMAIN_IDENTITY;
+	}
+
+	return 0;
+}
+
 static struct iommu_ops arm_smmu_ops = {
 	.capable		= arm_smmu_capable,
 	.domain_alloc		= arm_smmu_domain_alloc,
@@ -2856,6 +2902,7 @@
 	.sva_unbind		= arm_smmu_sva_unbind,
 	.sva_get_pasid		= arm_smmu_sva_get_pasid,
 	.page_response		= arm_smmu_page_response,
+	.def_domain_type	= arm_smmu_def_domain_type,
 	.pgsize_bitmap		= -1UL, /* Restricted during device attach */
 	.owner			= THIS_MODULE,
 };
@@ -3192,7 +3239,7 @@
 	}
 
 	/* Add callback to free MSIs on teardown */
-	devm_add_action(dev, arm_smmu_free_msis, dev);
+	devm_add_action_or_reset(dev, arm_smmu_free_msis, dev);
 }
 
 static void arm_smmu_setup_unique_irqs(struct arm_smmu_device *smmu)
@@ -3428,6 +3475,44 @@
 	return 0;
 }
 
+#define IIDR_IMPLEMENTER_ARM		0x43b
+#define IIDR_PRODUCTID_ARM_MMU_600	0x483
+#define IIDR_PRODUCTID_ARM_MMU_700	0x487
+
+static void arm_smmu_device_iidr_probe(struct arm_smmu_device *smmu)
+{
+	u32 reg;
+	unsigned int implementer, productid, variant, revision;
+
+	reg = readl_relaxed(smmu->base + ARM_SMMU_IIDR);
+	implementer = FIELD_GET(IIDR_IMPLEMENTER, reg);
+	productid = FIELD_GET(IIDR_PRODUCTID, reg);
+	variant = FIELD_GET(IIDR_VARIANT, reg);
+	revision = FIELD_GET(IIDR_REVISION, reg);
+
+	switch (implementer) {
+	case IIDR_IMPLEMENTER_ARM:
+		switch (productid) {
+		case IIDR_PRODUCTID_ARM_MMU_600:
+			/* Arm erratum 1076982 */
+			if (variant == 0 && revision <= 2)
+				smmu->features &= ~ARM_SMMU_FEAT_SEV;
+			/* Arm erratum 1209401 */
+			if (variant < 2)
+				smmu->features &= ~ARM_SMMU_FEAT_NESTING;
+			break;
+		case IIDR_PRODUCTID_ARM_MMU_700:
+			/* Arm erratum 2812531 */
+			smmu->features &= ~ARM_SMMU_FEAT_BTM;
+			smmu->options |= ARM_SMMU_OPT_CMDQ_FORCE_SYNC;
+			/* Arm errata 2268618, 2812531 */
+			smmu->features &= ~ARM_SMMU_FEAT_NESTING;
+			break;
+		}
+		break;
+	}
+}
+
 static int arm_smmu_device_hw_probe(struct arm_smmu_device *smmu)
 {
 	u32 reg;
@@ -3633,6 +3718,12 @@
 
 	smmu->ias = max(smmu->ias, smmu->oas);
 
+	if ((smmu->features & ARM_SMMU_FEAT_TRANS_S1) &&
+	    (smmu->features & ARM_SMMU_FEAT_TRANS_S2))
+		smmu->features |= ARM_SMMU_FEAT_NESTING;
+
+	arm_smmu_device_iidr_probe(smmu);
+
 	if (arm_smmu_sva_supported(smmu))
 		smmu->features |= ARM_SMMU_FEAT_SVA;
 
@@ -3785,6 +3876,8 @@
 
 	/* Base address */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
 	if (resource_size(res) < arm_smmu_resource_size(smmu)) {
 		dev_err(dev, "MMIO region too small (%pr)\n", res);
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h
@@ -69,6 +69,12 @@
 #define IDR5_VAX			GENMASK(11, 10)
 #define IDR5_VAX_52_BIT			1
 
+#define ARM_SMMU_IIDR			0x18
+#define IIDR_PRODUCTID			GENMASK(31, 20)
+#define IIDR_VARIANT			GENMASK(19, 16)
+#define IIDR_REVISION			GENMASK(15, 12)
+#define IIDR_IMPLEMENTER		GENMASK(11, 0)
+
 #define ARM_SMMU_CR0			0x20
 #define CR0_ATSCHK			(1 << 4)
 #define CR0_CMDQEN			(1 << 3)
@@ -640,11 +646,13 @@
 #define ARM_SMMU_FEAT_BTM		(1 << 16)
 #define ARM_SMMU_FEAT_SVA		(1 << 17)
 #define ARM_SMMU_FEAT_E2H		(1 << 18)
+#define ARM_SMMU_FEAT_NESTING		(1 << 19)
 	u32				features;
 
 #define ARM_SMMU_OPT_SKIP_PREFETCH	(1 << 0)
 #define ARM_SMMU_OPT_PAGE0_REGS_ONLY	(1 << 1)
 #define ARM_SMMU_OPT_MSIPOLL		(1 << 2)
+#define ARM_SMMU_OPT_CMDQ_FORCE_SYNC	(1 << 3)
 	u32				options;
 
 	struct arm_smmu_cmdq		cmdq;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu/arm-smmu-nvidia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu/arm-smmu-nvidia.c
@@ -258,6 +258,34 @@
 			dev_name(dev), err);
 }
 
+static int nvidia_smmu_init_context(struct arm_smmu_domain *smmu_domain,
+				    struct io_pgtable_cfg *pgtbl_cfg,
+				    struct device *dev)
+{
+	struct arm_smmu_device *smmu = smmu_domain->smmu;
+	const struct device_node *np = smmu->dev->of_node;
+
+	/*
+	 * Tegra194 and Tegra234 SoCs have the erratum that causes walk cache
+	 * entries to not be invalidated correctly. The problem is that the walk
+	 * cache index generated for IOVA is not same across translation and
+	 * invalidation requests. This is leading to page faults when PMD entry
+	 * is released during unmap and populated with new PTE table during
+	 * subsequent map request. Disabling large page mappings avoids the
+	 * release of PMD entry and avoid translations seeing stale PMD entry in
+	 * walk cache.
+	 * Fix this by limiting the page mappings to PAGE_SIZE on Tegra194 and
+	 * Tegra234.
+	 */
+	if (of_device_is_compatible(np, "nvidia,tegra234-smmu") ||
+	    of_device_is_compatible(np, "nvidia,tegra194-smmu")) {
+		smmu->pgsize_bitmap = PAGE_SIZE;
+		pgtbl_cfg->pgsize_bitmap = smmu->pgsize_bitmap;
+	}
+
+	return 0;
+}
+
 static const struct arm_smmu_impl nvidia_smmu_impl = {
 	.read_reg = nvidia_smmu_read_reg,
 	.write_reg = nvidia_smmu_write_reg,
@@ -268,10 +296,12 @@
 	.global_fault = nvidia_smmu_global_fault,
 	.context_fault = nvidia_smmu_context_fault,
 	.probe_finalize = nvidia_smmu_probe_finalize,
+	.init_context = nvidia_smmu_init_context,
 };
 
 static const struct arm_smmu_impl nvidia_smmu_single_impl = {
 	.probe_finalize = nvidia_smmu_probe_finalize,
+	.init_context = nvidia_smmu_init_context,
 };
 
 struct arm_smmu_device *nvidia_smmu_impl_init(struct arm_smmu_device *smmu)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
@@ -51,7 +51,7 @@
 	info->fsynr1 = arm_smmu_cb_read(smmu, cfg->cbndx, ARM_SMMU_CB_FSYNR1);
 	info->far = arm_smmu_cb_readq(smmu, cfg->cbndx, ARM_SMMU_CB_FAR);
 	info->cbfrsynra = arm_smmu_gr1_read(smmu, ARM_SMMU_GR1_CBFRSYNRA(cfg->cbndx));
-	info->ttbr0 = arm_smmu_cb_read(smmu, cfg->cbndx, ARM_SMMU_CB_TTBR0);
+	info->ttbr0 = arm_smmu_cb_readq(smmu, cfg->cbndx, ARM_SMMU_CB_TTBR0);
 	info->contextidr = arm_smmu_cb_read(smmu, cfg->cbndx, ARM_SMMU_CB_CONTEXTIDR);
 }
 
@@ -226,6 +226,7 @@
 
 static const struct of_device_id qcom_smmu_client_of_match[] __maybe_unused = {
 	{ .compatible = "qcom,adreno" },
+	{ .compatible = "qcom,adreno-gmu" },
 	{ .compatible = "qcom,mdp4" },
 	{ .compatible = "qcom,mdss" },
 	{ .compatible = "qcom,sc7180-mdss" },
@@ -247,13 +248,34 @@
 
 static int qcom_smmu_cfg_probe(struct arm_smmu_device *smmu)
 {
-	unsigned int last_s2cr = ARM_SMMU_GR0_S2CR(smmu->num_mapping_groups - 1);
 	struct qcom_smmu *qsmmu = to_qcom_smmu(smmu);
+	unsigned int last_s2cr;
 	u32 reg;
 	u32 smr;
 	int i;
 
 	/*
+	 * MSM8998 LPASS SMMU reports 13 context banks, but accessing
+	 * the last context bank crashes the system.
+	 */
+	if (of_device_is_compatible(smmu->dev->of_node, "qcom,msm8998-smmu-v2") && smmu->num_context_banks == 13)
+		smmu->num_context_banks = 12;
+
+	/*
+	 * Some platforms support more than the Arm SMMU architected maximum of
+	 * 128 stream matching groups. For unknown reasons, the additional
+	 * groups don't exhibit the same behavior as the architected registers,
+	 * so limit the groups to 128 until the behavior is fixed for the other
+	 * groups.
+	 */
+	if (smmu->num_mapping_groups > 128) {
+		dev_notice(smmu->dev, "\tLimiting the stream matching groups to 128\n");
+		smmu->num_mapping_groups = 128;
+	}
+
+	last_s2cr = ARM_SMMU_GR0_S2CR(smmu->num_mapping_groups - 1);
+
+	/*
 	 * With some firmware versions writes to S2CR of type FAULT are
 	 * ignored, and writing BYPASS will end up written as FAULT in the
 	 * register. Perform a write to S2CR to detect if this is the case and
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu/arm-smmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu/arm-smmu.c
@@ -1375,6 +1375,17 @@
 			goto out_free;
 	} else if (fwspec && fwspec->ops == &arm_smmu_ops) {
 		smmu = arm_smmu_get_by_fwnode(fwspec->iommu_fwnode);
+
+		/*
+		 * Defer probe if the relevant SMMU instance hasn't finished
+		 * probing yet. This is a fragile hack and we'd ideally
+		 * avoid this race in the core code. Until that's ironed
+		 * out, however, this is the most pragmatic option on the
+		 * table.
+		 */
+		if (!smmu)
+			return ERR_PTR(dev_err_probe(dev, -EPROBE_DEFER,
+						"smmu dev has not bound yet\n"));
 	} else {
 		return ERR_PTR(-ENODEV);
 	}
@@ -2090,11 +2101,10 @@
 	if (err)
 		return err;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	ioaddr = res->start;
-	smmu->base = devm_ioremap_resource(dev, res);
+	smmu->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 	if (IS_ERR(smmu->base))
 		return PTR_ERR(smmu->base);
+	ioaddr = res->start;
 	/*
 	 * The resource size should effectively match the value of SMMU_TOP;
 	 * stash that temporarily until we know PAGESIZE to validate it with.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/arm/arm-smmu/qcom_iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/arm/arm-smmu/qcom_iommu.c
@@ -273,6 +273,13 @@
 			ctx->secure_init = true;
 		}
 
+		/* Disable context bank before programming */
+		iommu_writel(ctx, ARM_SMMU_CB_SCTLR, 0);
+
+		/* Clear context bank fault address fault status registers */
+		iommu_writel(ctx, ARM_SMMU_CB_FAR, 0);
+		iommu_writel(ctx, ARM_SMMU_CB_FSR, ARM_SMMU_FSR_FAULT);
+
 		/* TTBRs */
 		iommu_writeq(ctx, ARM_SMMU_CB_TTBR0,
 				pgtbl_cfg.arm_lpae_s1_cfg.ttbr |
@@ -748,9 +755,12 @@
 {
 	struct device_node *child;
 
-	for_each_child_of_node(qcom_iommu->dev->of_node, child)
-		if (of_device_is_compatible(child, "qcom,msm-iommu-v1-sec"))
+	for_each_child_of_node(qcom_iommu->dev->of_node, child) {
+		if (of_device_is_compatible(child, "qcom,msm-iommu-v1-sec")) {
+			of_node_put(child);
 			return true;
+		}
+	}
 
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/dma-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/dma-iommu.c
@@ -25,6 +25,7 @@
 #include <linux/vmalloc.h>
 #include <linux/crash_dump.h>
 #include <linux/dma-direct.h>
+#include <trace/events/swiotlb.h>
 
 struct iommu_dma_msi_page {
 	struct list_head	list;
@@ -317,6 +318,11 @@
 	return dev_is_pci(dev) && to_pci_dev(dev)->untrusted;
 }
 
+static bool dev_use_swiotlb(struct device *dev)
+{
+	return IS_ENABLED(CONFIG_SWIOTLB) && dev_is_untrusted(dev);
+}
+
 /* sysfs updates are serialised by the mutex of the group owning @domain */
 int iommu_dma_init_fq(struct iommu_domain *domain)
 {
@@ -510,23 +516,6 @@
 	iommu_dma_free_iova(cookie, dma_addr, size, &iotlb_gather);
 }
 
-static void __iommu_dma_unmap_swiotlb(struct device *dev, dma_addr_t dma_addr,
-		size_t size, enum dma_data_direction dir,
-		unsigned long attrs)
-{
-	struct iommu_domain *domain = iommu_get_dma_domain(dev);
-	phys_addr_t phys;
-
-	phys = iommu_iova_to_phys(domain, dma_addr);
-	if (WARN_ON(!phys))
-		return;
-
-	__iommu_dma_unmap(dev, dma_addr, size);
-
-	if (unlikely(is_swiotlb_buffer(dev, phys)))
-		swiotlb_tbl_unmap_single(dev, phys, size, dir, attrs);
-}
-
 static dma_addr_t __iommu_dma_map(struct device *dev, phys_addr_t phys,
 		size_t size, int prot, u64 dma_mask)
 {
@@ -553,52 +542,6 @@
 	return iova + iova_off;
 }
 
-static dma_addr_t __iommu_dma_map_swiotlb(struct device *dev, phys_addr_t phys,
-		size_t org_size, dma_addr_t dma_mask, bool coherent,
-		enum dma_data_direction dir, unsigned long attrs)
-{
-	int prot = dma_info_to_prot(dir, coherent, attrs);
-	struct iommu_domain *domain = iommu_get_dma_domain(dev);
-	struct iommu_dma_cookie *cookie = domain->iova_cookie;
-	struct iova_domain *iovad = &cookie->iovad;
-	size_t aligned_size = org_size;
-	void *padding_start;
-	size_t padding_size;
-	dma_addr_t iova;
-
-	/*
-	 * If both the physical buffer start address and size are
-	 * page aligned, we don't need to use a bounce page.
-	 */
-	if (IS_ENABLED(CONFIG_SWIOTLB) && dev_is_untrusted(dev) &&
-	    iova_offset(iovad, phys | org_size)) {
-		aligned_size = iova_align(iovad, org_size);
-		phys = swiotlb_tbl_map_single(dev, phys, org_size,
-					      aligned_size, dir, attrs);
-
-		if (phys == DMA_MAPPING_ERROR)
-			return DMA_MAPPING_ERROR;
-
-		/* Cleanup the padding area. */
-		padding_start = phys_to_virt(phys);
-		padding_size = aligned_size;
-
-		if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC) &&
-		    (dir == DMA_TO_DEVICE ||
-		     dir == DMA_BIDIRECTIONAL)) {
-			padding_start += org_size;
-			padding_size -= org_size;
-		}
-
-		memset(padding_start, 0, padding_size);
-	}
-
-	iova = __iommu_dma_map(dev, phys, aligned_size, prot, dma_mask);
-	if (iova == DMA_MAPPING_ERROR && is_swiotlb_buffer(dev, phys))
-		swiotlb_tbl_unmap_single(dev, phys, org_size, dir, attrs);
-	return iova;
-}
-
 static void __iommu_dma_free_pages(struct page **pages, int count)
 {
 	while (count--)
@@ -677,6 +620,7 @@
 	unsigned int count, min_size, alloc_sizes = domain->pgsize_bitmap;
 	struct page **pages;
 	dma_addr_t iova;
+	ssize_t ret;
 
 	if (static_branch_unlikely(&iommu_deferred_attach_enabled) &&
 	    iommu_deferred_attach(dev, domain))
@@ -714,8 +658,8 @@
 			arch_dma_prep_coherent(sg_page(sg), sg->length);
 	}
 
-	if (iommu_map_sg_atomic(domain, iova, sgt->sgl, sgt->orig_nents, ioprot)
-			< size)
+	ret = iommu_map_sg_atomic(domain, iova, sgt->sgl, sgt->orig_nents, ioprot);
+	if (ret < 0 || ret < size)
 		goto out_free_sg;
 
 	sgt->sgl->dma_address = iova;
@@ -794,7 +738,7 @@
 {
 	phys_addr_t phys;
 
-	if (dev_is_dma_coherent(dev) && !dev_is_untrusted(dev))
+	if (dev_is_dma_coherent(dev) && !dev_use_swiotlb(dev))
 		return;
 
 	phys = iommu_iova_to_phys(iommu_get_dma_domain(dev), dma_handle);
@@ -810,7 +754,7 @@
 {
 	phys_addr_t phys;
 
-	if (dev_is_dma_coherent(dev) && !dev_is_untrusted(dev))
+	if (dev_is_dma_coherent(dev) && !dev_use_swiotlb(dev))
 		return;
 
 	phys = iommu_iova_to_phys(iommu_get_dma_domain(dev), dma_handle);
@@ -828,17 +772,13 @@
 	struct scatterlist *sg;
 	int i;
 
-	if (dev_is_dma_coherent(dev) && !dev_is_untrusted(dev))
-		return;
-
-	for_each_sg(sgl, sg, nelems, i) {
-		if (!dev_is_dma_coherent(dev))
+	if (dev_use_swiotlb(dev))
+		for_each_sg(sgl, sg, nelems, i)
+			iommu_dma_sync_single_for_cpu(dev, sg_dma_address(sg),
+						      sg->length, dir);
+	else if (!dev_is_dma_coherent(dev))
+		for_each_sg(sgl, sg, nelems, i)
 			arch_sync_dma_for_cpu(sg_phys(sg), sg->length, dir);
-
-		if (is_swiotlb_buffer(dev, sg_phys(sg)))
-			swiotlb_sync_single_for_cpu(dev, sg_phys(sg),
-						    sg->length, dir);
-	}
 }
 
 static void iommu_dma_sync_sg_for_device(struct device *dev,
@@ -848,17 +788,14 @@
 	struct scatterlist *sg;
 	int i;
 
-	if (dev_is_dma_coherent(dev) && !dev_is_untrusted(dev))
-		return;
-
-	for_each_sg(sgl, sg, nelems, i) {
-		if (is_swiotlb_buffer(dev, sg_phys(sg)))
-			swiotlb_sync_single_for_device(dev, sg_phys(sg),
-						       sg->length, dir);
-
-		if (!dev_is_dma_coherent(dev))
+	if (dev_use_swiotlb(dev))
+		for_each_sg(sgl, sg, nelems, i)
+			iommu_dma_sync_single_for_device(dev,
+							 sg_dma_address(sg),
+							 sg->length, dir);
+	else if (!dev_is_dma_coherent(dev))
+		for_each_sg(sgl, sg, nelems, i)
 			arch_sync_dma_for_device(sg_phys(sg), sg->length, dir);
-	}
 }
 
 static dma_addr_t iommu_dma_map_page(struct device *dev, struct page *page,
@@ -867,22 +804,68 @@
 {
 	phys_addr_t phys = page_to_phys(page) + offset;
 	bool coherent = dev_is_dma_coherent(dev);
-	dma_addr_t dma_handle;
+	int prot = dma_info_to_prot(dir, coherent, attrs);
+	struct iommu_domain *domain = iommu_get_dma_domain(dev);
+	struct iommu_dma_cookie *cookie = domain->iova_cookie;
+	struct iova_domain *iovad = &cookie->iovad;
+	dma_addr_t iova, dma_mask = dma_get_mask(dev);
+
+	/*
+	 * If both the physical buffer start address and size are
+	 * page aligned, we don't need to use a bounce page.
+	 */
+	if (dev_use_swiotlb(dev) && iova_offset(iovad, phys | size)) {
+		void *padding_start;
+		size_t padding_size, aligned_size;
+
+		trace_swiotlb_bounced(dev, phys, size, swiotlb_force);
+
+		aligned_size = iova_align(iovad, size);
+		phys = swiotlb_tbl_map_single(dev, phys, size, aligned_size,
+					      iova_mask(iovad), dir, attrs);
+
+		if (phys == DMA_MAPPING_ERROR)
+			return DMA_MAPPING_ERROR;
+
+		/* Cleanup the padding area. */
+		padding_start = phys_to_virt(phys);
+		padding_size = aligned_size;
 
-	dma_handle = __iommu_dma_map_swiotlb(dev, phys, size, dma_get_mask(dev),
-			coherent, dir, attrs);
-	if (!coherent && !(attrs & DMA_ATTR_SKIP_CPU_SYNC) &&
-	    dma_handle != DMA_MAPPING_ERROR)
+		if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC) &&
+		    (dir == DMA_TO_DEVICE || dir == DMA_BIDIRECTIONAL)) {
+			padding_start += size;
+			padding_size -= size;
+		}
+
+		memset(padding_start, 0, padding_size);
+	}
+
+	if (!coherent && !(attrs & DMA_ATTR_SKIP_CPU_SYNC))
 		arch_sync_dma_for_device(phys, size, dir);
-	return dma_handle;
+
+	iova = __iommu_dma_map(dev, phys, size, prot, dma_mask);
+	if (iova == DMA_MAPPING_ERROR && is_swiotlb_buffer(dev, phys))
+		swiotlb_tbl_unmap_single(dev, phys, size, dir, attrs);
+	return iova;
 }
 
 static void iommu_dma_unmap_page(struct device *dev, dma_addr_t dma_handle,
 		size_t size, enum dma_data_direction dir, unsigned long attrs)
 {
-	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
-		iommu_dma_sync_single_for_cpu(dev, dma_handle, size, dir);
-	__iommu_dma_unmap_swiotlb(dev, dma_handle, size, dir, attrs);
+	struct iommu_domain *domain = iommu_get_dma_domain(dev);
+	phys_addr_t phys;
+
+	phys = iommu_iova_to_phys(domain, dma_handle);
+	if (WARN_ON(!phys))
+		return;
+
+	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC) && !dev_is_dma_coherent(dev))
+		arch_sync_dma_for_cpu(phys, size, dir);
+
+	__iommu_dma_unmap(dev, dma_handle, size);
+
+	if (unlikely(is_swiotlb_buffer(dev, phys)))
+		swiotlb_tbl_unmap_single(dev, phys, size, dir, attrs);
 }
 
 /*
@@ -967,7 +950,7 @@
 	int i;
 
 	for_each_sg(sg, s, nents, i)
-		__iommu_dma_unmap_swiotlb(dev, sg_dma_address(s),
+		iommu_dma_unmap_page(dev, sg_dma_address(s),
 				sg_dma_len(s), dir, attrs);
 }
 
@@ -978,9 +961,8 @@
 	int i;
 
 	for_each_sg(sg, s, nents, i) {
-		sg_dma_address(s) = __iommu_dma_map_swiotlb(dev, sg_phys(s),
-				s->length, dma_get_mask(dev),
-				dev_is_dma_coherent(dev), dir, attrs);
+		sg_dma_address(s) = iommu_dma_map_page(dev, sg_page(s),
+				s->offset, s->length, dir, attrs);
 		if (sg_dma_address(s) == DMA_MAPPING_ERROR)
 			goto out_unmap;
 		sg_dma_len(s) = s->length;
@@ -1016,15 +998,16 @@
 
 	if (static_branch_unlikely(&iommu_deferred_attach_enabled)) {
 		ret = iommu_deferred_attach(dev, domain);
-		goto out;
+		if (ret)
+			goto out;
 	}
 
+	if (dev_use_swiotlb(dev))
+		return iommu_dma_map_sg_swiotlb(dev, sg, nents, dir, attrs);
+
 	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
 		iommu_dma_sync_sg_for_device(dev, sg, nents, dir);
 
-	if (dev_is_untrusted(dev))
-		return iommu_dma_map_sg_swiotlb(dev, sg, nents, dir, attrs);
-
 	/*
 	 * Work out how much IOVA space we need, and align the segments to
 	 * IOVA granules for the IOMMU driver to handle. With some clever
@@ -1075,7 +1058,7 @@
 	 * implementation - it knows better than we do.
 	 */
 	ret = iommu_map_sg_atomic(domain, iova, sg, nents, prot);
-	if (ret < iova_len)
+	if (ret < 0 || ret < iova_len)
 		goto out_free_iova;
 
 	return __finalise_sg(dev, sg, nents, iova);
@@ -1097,14 +1080,14 @@
 	struct scatterlist *tmp;
 	int i;
 
-	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
-		iommu_dma_sync_sg_for_cpu(dev, sg, nents, dir);
-
-	if (dev_is_untrusted(dev)) {
+	if (dev_use_swiotlb(dev)) {
 		iommu_dma_unmap_sg_swiotlb(dev, sg, nents, dir, attrs);
 		return;
 	}
 
+	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
+		iommu_dma_sync_sg_for_cpu(dev, sg, nents, dir);
+
 	/*
 	 * The scatterlist segments are mapped into a single
 	 * contiguous IOVA allocation, so this is incredibly easy.
@@ -1308,6 +1291,19 @@
 	return (1UL << __ffs(domain->pgsize_bitmap)) - 1;
 }
 
+static size_t iommu_dma_opt_mapping_size(void)
+{
+	return iova_rcache_range();
+}
+
+static size_t iommu_dma_max_mapping_size(struct device *dev)
+{
+	if (dev_is_untrusted(dev))
+		return swiotlb_max_mapping_size(dev);
+
+	return SIZE_MAX;
+}
+
 static const struct dma_map_ops iommu_dma_ops = {
 	.alloc			= iommu_dma_alloc,
 	.free			= iommu_dma_free,
@@ -1330,6 +1326,8 @@
 	.map_resource		= iommu_dma_map_resource,
 	.unmap_resource		= iommu_dma_unmap_resource,
 	.get_merge_boundary	= iommu_dma_get_merge_boundary,
+	.opt_mapping_size	= iommu_dma_opt_mapping_size,
+	.max_mapping_size       = iommu_dma_max_mapping_size,
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/exynos-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/exynos-iommu.c
@@ -630,7 +630,7 @@
 
 	ret = iommu_device_register(&data->iommu, &exynos_iommu_ops, dev);
 	if (ret)
-		return ret;
+		goto err_iommu_register;
 
 	platform_set_drvdata(pdev, data);
 
@@ -657,6 +657,10 @@
 	pm_runtime_enable(dev);
 
 	return 0;
+
+err_iommu_register:
+	iommu_device_sysfs_remove(&data->iommu);
+	return ret;
 }
 
 static int __maybe_unused exynos_sysmmu_suspend(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/fsl_pamu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/fsl_pamu.c
@@ -865,7 +865,7 @@
 		ret = create_csd(ppaact_phys, mem_size, csd_port_id);
 		if (ret) {
 			dev_err(dev, "could not create coherence subdomain\n");
-			return ret;
+			goto error;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/cap_audit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/cap_audit.c
@@ -144,6 +144,7 @@
 {
 	struct dmar_drhd_unit *d;
 	struct intel_iommu *i;
+	int rc = 0;
 
 	rcu_read_lock();
 	if (list_empty(&dmar_drhd_units))
@@ -163,9 +164,17 @@
 			check_irq_capabilities(iommu, i);
 	}
 
+	/*
+	 * If the system is sane to support scalable mode, either SL or FL
+	 * should be sane.
+	 */
+	if (intel_cap_smts_sanity() &&
+	    !intel_cap_flts_sanity() && !intel_cap_slts_sanity())
+		rc = -EOPNOTSUPP;
+
 out:
 	rcu_read_unlock();
-	return 0;
+	return rc;
 }
 
 int intel_cap_audit(enum cap_audit_type type, struct intel_iommu *iommu)
@@ -203,3 +212,8 @@
 {
 	return ecap_flts(intel_iommu_ecap_sanity);
 }
+
+bool intel_cap_slts_sanity(void)
+{
+	return ecap_slts(intel_iommu_ecap_sanity);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/cap_audit.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/cap_audit.h
@@ -111,6 +111,7 @@
 bool intel_cap_pasid_sanity(void);
 bool intel_cap_nest_sanity(void);
 bool intel_cap_flts_sanity(void);
+bool intel_cap_slts_sanity(void);
 
 static inline bool scalable_mode_support(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/dmar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/dmar.c
@@ -385,7 +385,7 @@
 
 static struct notifier_block dmar_pci_bus_nb = {
 	.notifier_call = dmar_pci_bus_notifier,
-	.priority = INT_MIN,
+	.priority = 1,
 };
 
 static struct dmar_drhd_unit *
@@ -497,7 +497,7 @@
 		if (drhd->reg_base_addr == rhsa->base_address) {
 			int node = pxm_to_node(rhsa->proximity_domain);
 
-			if (!node_online(node))
+			if (node != NUMA_NO_NODE && !node_online(node))
 				node = NUMA_NO_NODE;
 			drhd->iommu->node = node;
 			return 0;
@@ -822,6 +822,7 @@
 			info = dmar_alloc_pci_notify_info(dev,
 					BUS_NOTIFY_ADD_DEVICE);
 			if (!info) {
+				pci_dev_put(dev);
 				return dmar_dev_scope_status;
 			} else {
 				dmar_pci_bus_add_dev(info);
@@ -1079,7 +1080,8 @@
 	}
 
 	err = -EINVAL;
-	if (cap_sagaw(iommu->cap) == 0) {
+	if (!cap_sagaw(iommu->cap) &&
+	    (!ecap_smts(iommu->ecap) || ecap_slts(iommu->ecap))) {
 		pr_info("%s: No supported address widths. Not attempting DMA translation.\n",
 			iommu->name);
 		drhd->ignored = 1;
@@ -1196,9 +1198,7 @@
  */
 static inline void reclaim_free_desc(struct q_inval *qi)
 {
-	while (qi->desc_status[qi->free_tail] == QI_DONE ||
-	       qi->desc_status[qi->free_tail] == QI_ABORT) {
-		qi->desc_status[qi->free_tail] = QI_FREE;
+	while (qi->desc_status[qi->free_tail] == QI_FREE && qi->free_tail != qi->free_head) {
 		qi->free_tail = (qi->free_tail + 1) % QI_LENGTH;
 		qi->free_cnt++;
 	}
@@ -1416,7 +1416,7 @@
 	 */
 	writel(qi->free_head << shift, iommu->reg + DMAR_IQT_REG);
 
-	while (qi->desc_status[wait_index] != QI_DONE) {
+	while (READ_ONCE(qi->desc_status[wait_index]) != QI_DONE) {
 		/*
 		 * We will leave the interrupts disabled, to prevent interrupt
 		 * context to queue another cmd while a cmd is already submitted
@@ -1433,8 +1433,16 @@
 		raw_spin_lock(&qi->q_lock);
 	}
 
-	for (i = 0; i < count; i++)
-		qi->desc_status[(index + i) % QI_LENGTH] = QI_DONE;
+	/*
+	 * The reclaim code can free descriptors from multiple submissions
+	 * starting from the tail of the queue. When count == 0, the
+	 * status of the standalone wait descriptor at the tail of the queue
+	 * must be set to QI_FREE to allow the reclaim code to proceed.
+	 * It is also possible that descriptors from one of the previous
+	 * submissions has to be reclaimed by a subsequent submission.
+	 */
+	for (i = 0; i <= count; i++)
+		qi->desc_status[(index + i) % QI_LENGTH] = QI_FREE;
 
 	reclaim_free_desc(qi);
 	raw_spin_unlock_irqrestore(&qi->q_lock, flags);
@@ -1516,6 +1524,15 @@
 {
 	struct qi_desc desc;
 
+	/*
+	 * VT-d spec, section 4.3:
+	 *
+	 * Software is recommended to not submit any Device-TLB invalidation
+	 * requests while address remapping hardware is disabled.
+	 */
+	if (!(iommu->gcmd & DMA_GCMD_TE))
+		return;
+
 	if (mask) {
 		addr |= (1ULL << (VTD_PAGE_SHIFT + mask - 1)) - 1;
 		desc.qw1 = QI_DEV_IOTLB_ADDR(addr) | QI_DEV_IOTLB_SIZE;
@@ -1581,6 +1598,15 @@
 	unsigned long mask = 1UL << (VTD_PAGE_SHIFT + size_order - 1);
 	struct qi_desc desc = {.qw1 = 0, .qw2 = 0, .qw3 = 0};
 
+	/*
+	 * VT-d spec, section 4.3:
+	 *
+	 * Software is recommended to not submit any Device-TLB invalidation
+	 * requests while address remapping hardware is disabled.
+	 */
+	if (!(iommu->gcmd & DMA_GCMD_TE))
+		return;
+
 	desc.qw0 = QI_DEV_EIOTLB_PASID(pasid) | QI_DEV_EIOTLB_SID(sid) |
 		QI_DEV_EIOTLB_QDEP(qdep) | QI_DEIOTLB_TYPE |
 		QI_DEV_IOTLB_PFSID(pfsid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/iommu.c
@@ -57,6 +57,12 @@
 #define IS_GFX_DEVICE(pdev) ((pdev->class >> 16) == PCI_BASE_CLASS_DISPLAY)
 #define IS_USB_DEVICE(pdev) ((pdev->class >> 8) == PCI_CLASS_SERIAL_USB)
 #define IS_ISA_DEVICE(pdev) ((pdev->class >> 8) == PCI_CLASS_BRIDGE_ISA)
+#define IS_INTEL_IPU(pdev) ((pdev)->vendor == PCI_VENDOR_ID_INTEL &&	\
+			   ((pdev)->device == 0x9a19 ||		\
+			    (pdev)->device == 0x9a39 ||		\
+			    (pdev)->device == 0x4e19 ||		\
+			    (pdev)->device == 0x465d ||		\
+			    (pdev)->device == 0x1919))
 #define IS_AZALIA(pdev) ((pdev)->vendor == 0x8086 && (pdev)->device == 0x3a3e)
 
 #define IOAPIC_RANGE_START	(0xfee00000)
@@ -191,38 +197,6 @@
 	return re->hi & VTD_PAGE_MASK;
 }
 
-static inline void context_clear_pasid_enable(struct context_entry *context)
-{
-	context->lo &= ~(1ULL << 11);
-}
-
-static inline bool context_pasid_enabled(struct context_entry *context)
-{
-	return !!(context->lo & (1ULL << 11));
-}
-
-static inline void context_set_copied(struct context_entry *context)
-{
-	context->hi |= (1ull << 3);
-}
-
-static inline bool context_copied(struct context_entry *context)
-{
-	return !!(context->hi & (1ULL << 3));
-}
-
-static inline bool __context_present(struct context_entry *context)
-{
-	return (context->lo & 1);
-}
-
-bool context_present(struct context_entry *context)
-{
-	return context_pasid_enabled(context) ?
-	     __context_present(context) :
-	     __context_present(context) && !context_copied(context);
-}
-
 static inline void context_set_present(struct context_entry *context)
 {
 	context->lo |= 1;
@@ -270,6 +244,26 @@
 	context->hi = 0;
 }
 
+static inline bool context_copied(struct intel_iommu *iommu, u8 bus, u8 devfn)
+{
+	if (!iommu->copied_tables)
+		return false;
+
+	return test_bit(((long)bus << 8) | devfn, iommu->copied_tables);
+}
+
+static inline void
+set_context_copied(struct intel_iommu *iommu, u8 bus, u8 devfn)
+{
+	set_bit(((long)bus << 8) | devfn, iommu->copied_tables);
+}
+
+static inline void
+clear_context_copied(struct intel_iommu *iommu, u8 bus, u8 devfn)
+{
+	clear_bit(((long)bus << 8) | devfn, iommu->copied_tables);
+}
+
 /*
  * This domain is a statically identity mapping domain.
  *	1. This domain creats a static 1:1 mapping to all usable memory.
@@ -335,12 +329,14 @@
 EXPORT_SYMBOL_GPL(intel_iommu_enabled);
 
 static int dmar_map_gfx = 1;
+static int dmar_map_ipu = 1;
 static int intel_iommu_superpage = 1;
 static int iommu_identity_mapping;
 static int iommu_skip_te_disable;
 
 #define IDENTMAP_GFX		2
 #define IDENTMAP_AZALIA		4
+#define IDENTMAP_IPU		8
 
 int intel_iommu_gfx_mapped;
 EXPORT_SYMBOL_GPL(intel_iommu_gfx_mapped);
@@ -363,30 +359,6 @@
 DEFINE_SPINLOCK(device_domain_lock);
 static LIST_HEAD(device_domain_list);
 
-/*
- * Iterate over elements in device_domain_list and call the specified
- * callback @fn against each element.
- */
-int for_each_device_domain(int (*fn)(struct device_domain_info *info,
-				     void *data), void *data)
-{
-	int ret = 0;
-	unsigned long flags;
-	struct device_domain_info *info;
-
-	spin_lock_irqsave(&device_domain_lock, flags);
-	list_for_each_entry(info, &device_domain_list, global) {
-		ret = fn(info, data);
-		if (ret) {
-			spin_unlock_irqrestore(&device_domain_lock, flags);
-			return ret;
-		}
-	}
-	spin_unlock_irqrestore(&device_domain_lock, flags);
-
-	return 0;
-}
-
 const struct iommu_ops intel_iommu_ops;
 
 static bool translation_pre_enabled(struct intel_iommu *iommu)
@@ -412,6 +384,7 @@
 {
 	if (!str)
 		return -EINVAL;
+
 	while (*str) {
 		if (!strncmp(str, "on", 2)) {
 			dmar_disabled = 0;
@@ -441,13 +414,16 @@
 		} else if (!strncmp(str, "tboot_noforce", 13)) {
 			pr_info("Intel-IOMMU: not forcing on after tboot. This could expose security risk for tboot\n");
 			intel_iommu_tboot_noforce = 1;
+		} else {
+			pr_notice("Unknown option - '%s'\n", str);
 		}
 
 		str += strcspn(str, ",");
 		while (*str == ',')
 			str++;
 	}
-	return 0;
+
+	return 1;
 }
 __setup("intel_iommu=", intel_iommu_setup);
 
@@ -522,7 +498,7 @@
 
 static inline int domain_type_is_si(struct dmar_domain *domain)
 {
-	return domain->flags & DOMAIN_FLAG_STATIC_IDENTITY;
+	return domain->domain.type == IOMMU_DOMAIN_IDENTITY;
 }
 
 static inline bool domain_use_first_level(struct dmar_domain *domain)
@@ -538,14 +514,36 @@
 	return !(addr_width < BITS_PER_LONG && pfn >> addr_width);
 }
 
+/*
+ * Calculate the Supported Adjusted Guest Address Widths of an IOMMU.
+ * Refer to 11.4.2 of the VT-d spec for the encoding of each bit of
+ * the returned SAGAW.
+ */
+static unsigned long __iommu_calculate_sagaw(struct intel_iommu *iommu)
+{
+	unsigned long fl_sagaw, sl_sagaw;
+
+	fl_sagaw = BIT(2) | (cap_5lp_support(iommu->cap) ? BIT(3) : 0);
+	sl_sagaw = cap_sagaw(iommu->cap);
+
+	/* Second level only. */
+	if (!sm_supported(iommu) || !ecap_flts(iommu->ecap))
+		return sl_sagaw;
+
+	/* First level only. */
+	if (!ecap_slts(iommu->ecap))
+		return fl_sagaw;
+
+	return fl_sagaw & sl_sagaw;
+}
+
 static int __iommu_calculate_agaw(struct intel_iommu *iommu, int max_gaw)
 {
 	unsigned long sagaw;
 	int agaw;
 
-	sagaw = cap_sagaw(iommu->cap);
-	for (agaw = width_to_agaw(max_gaw);
-	     agaw >= 0; agaw--) {
+	sagaw = __iommu_calculate_sagaw(iommu);
+	for (agaw = width_to_agaw(max_gaw); agaw >= 0; agaw--) {
 		if (test_bit(agaw, &sagaw))
 			break;
 	}
@@ -766,6 +764,13 @@
 	struct context_entry *context;
 	u64 *entry;
 
+	/*
+	 * Except that the caller requested to allocate a new entry,
+	 * returning a copied context entry makes no sense.
+	 */
+	if (!alloc && context_copied(iommu, bus, devfn))
+		return NULL;
+
 	entry = &root->lo;
 	if (sm_supported(iommu)) {
 		if (devfn >= 0x80) {
@@ -1027,11 +1032,9 @@
 
 			domain_flush_cache(domain, tmp_page, VTD_PAGE_SIZE);
 			pteval = ((uint64_t)virt_to_dma_pfn(tmp_page) << VTD_PAGE_SHIFT) | DMA_PTE_READ | DMA_PTE_WRITE;
-			if (domain_use_first_level(domain)) {
-				pteval |= DMA_FL_PTE_XD | DMA_FL_PTE_US;
-				if (iommu_is_dma_domain(&domain->domain))
-					pteval |= DMA_FL_PTE_ACCESS;
-			}
+			if (domain_use_first_level(domain))
+				pteval |= DMA_FL_PTE_XD | DMA_FL_PTE_US | DMA_FL_PTE_ACCESS;
+
 			if (cmpxchg64(&pte->val, 0ULL, pteval))
 				/* Someone else set it while we were thinking; use theirs. */
 				free_pgtable_page(tmp_page);
@@ -1222,13 +1225,11 @@
 	pte = &pte[pfn_level_offset(pfn, level)];
 
 	do {
-		unsigned long level_pfn;
+		unsigned long level_pfn = pfn & level_mask(level);
 
 		if (!dma_pte_present(pte))
 			goto next;
 
-		level_pfn = pfn & level_mask(level);
-
 		/* If range covers entire pagetable, free it */
 		if (start_pfn <= level_pfn &&
 		    last_pfn >= level_pfn + level_size(level) - 1) {
@@ -1249,7 +1250,7 @@
 						       freelist);
 		}
 next:
-		pfn += level_size(level);
+		pfn = level_pfn + level_size(level);
 	} while (!first_pte_in_page(++pte) && pfn <= last_pfn);
 
 	if (first_pte)
@@ -1635,7 +1636,8 @@
 				  unsigned long pfn, unsigned int pages,
 				  int ih, int map)
 {
-	unsigned int mask = ilog2(__roundup_pow_of_two(pages));
+	unsigned int aligned_pages = __roundup_pow_of_two(pages);
+	unsigned int mask = ilog2(aligned_pages);
 	uint64_t addr = (uint64_t)pfn << VTD_PAGE_SHIFT;
 	u16 did = domain->iommu_did[iommu->seq_id];
 
@@ -1647,10 +1649,30 @@
 	if (domain_use_first_level(domain)) {
 		domain_flush_piotlb(iommu, domain, addr, pages, ih);
 	} else {
+		unsigned long bitmask = aligned_pages - 1;
+
+		/*
+		 * PSI masks the low order bits of the base address. If the
+		 * address isn't aligned to the mask, then compute a mask value
+		 * needed to ensure the target range is flushed.
+		 */
+		if (unlikely(bitmask & pfn)) {
+			unsigned long end_pfn = pfn + pages - 1, shared_bits;
+
+			/*
+			 * Since end_pfn <= pfn + bitmask, the only way bits
+			 * higher than bitmask can differ in pfn and end_pfn is
+			 * by carrying. This means after masking out bitmask,
+			 * high bits starting with the first set bit in
+			 * shared_bits are all equal in both pfn and end_pfn.
+			 */
+			shared_bits = ~(pfn ^ end_pfn) & ~bitmask;
+			mask = shared_bits ? __ffs(shared_bits) : BITS_PER_LONG;
+		}
+
 		/*
 		 * Fallback to domain selective flush if no PSI support or
-		 * the size is too big. PSI requires page size to be 2 ^ x,
-		 * and the base address is naturally aligned to the size.
+		 * the size is too big.
 		 */
 		if (!cap_pgsel_inv(iommu->cap) ||
 		    mask > cap_max_amask_val(iommu->cap))
@@ -1808,10 +1830,10 @@
 	 * entry for first-level or pass-through translation modes should
 	 * be programmed with a domain id different from those used for
 	 * second-level or nested translation. We reserve a domain id for
-	 * this purpose.
+	 * this purpose. This domain id is also used for identity domain
+	 * in legacy mode.
 	 */
-	if (sm_supported(iommu))
-		set_bit(FLPT_DEFAULT_DID, iommu->domain_ids);
+	set_bit(FLPT_DEFAULT_DID, iommu->domain_ids);
 
 	return 0;
 }
@@ -1854,6 +1876,11 @@
 		iommu->domain_ids = NULL;
 	}
 
+	if (iommu->copied_tables) {
+		bitmap_free(iommu->copied_tables);
+		iommu->copied_tables = NULL;
+	}
+
 	g_iommus[iommu->seq_id] = NULL;
 
 	/* free context mapping */
@@ -1874,12 +1901,21 @@
  * Check and return whether first level is used by default for
  * DMA translation.
  */
-static bool first_level_by_default(void)
+static bool first_level_by_default(unsigned int type)
 {
-	return scalable_mode_support() && intel_cap_flts_sanity();
+	/* Only SL is available in legacy mode */
+	if (!scalable_mode_support())
+		return false;
+
+	/* Only level (either FL or SL) is available, just use it */
+	if (intel_cap_flts_sanity() ^ intel_cap_slts_sanity())
+		return intel_cap_flts_sanity();
+
+	/* Both levels are available, decide it based on domain type */
+	return type != IOMMU_DOMAIN_UNMANAGED;
 }
 
-static struct dmar_domain *alloc_domain(int flags)
+static struct dmar_domain *alloc_domain(unsigned int type)
 {
 	struct dmar_domain *domain;
 
@@ -1889,8 +1925,7 @@
 
 	memset(domain, 0, sizeof(*domain));
 	domain->nid = NUMA_NO_NODE;
-	domain->flags = flags;
-	if (first_level_by_default())
+	if (first_level_by_default(type))
 		domain->flags |= DOMAIN_FLAG_USE_FIRST_LEVEL;
 	domain->has_iotlb_device = false;
 	INIT_LIST_HEAD(&domain->devices);
@@ -2062,7 +2097,7 @@
 		goto out_unlock;
 
 	ret = 0;
-	if (context_present(context))
+	if (context_present(context) && !context_copied(iommu, bus, devfn))
 		goto out_unlock;
 
 	/*
@@ -2074,7 +2109,7 @@
 	 * in-flight DMA will exist, and we don't need to worry anymore
 	 * hereafter.
 	 */
-	if (context_copied(context)) {
+	if (context_copied(iommu, bus, devfn)) {
 		u16 did_old = context_domain_id(context);
 
 		if (did_old < cap_ndoms(iommu->cap)) {
@@ -2085,6 +2120,8 @@
 			iommu->flush.flush_iotlb(iommu, did_old, 0, 0,
 						 DMA_TLB_DSI_FLUSH);
 		}
+
+		clear_context_copied(iommu, bus, devfn);
 	}
 
 	context_clear_entry(context);
@@ -2649,7 +2686,7 @@
 	spin_unlock_irqrestore(&device_domain_lock, flags);
 
 	/* PASID table is mandatory for a PCI device in scalable mode. */
-	if (dev && dev_is_pci(dev) && sm_supported(iommu)) {
+	if (sm_supported(iommu) && !dev_is_real_dma_subdevice(dev)) {
 		ret = intel_pasid_alloc_table(dev);
 		if (ret) {
 			dev_err(dev, "PASID table allocation failed\n");
@@ -2708,12 +2745,13 @@
 	struct device *dev;
 	int i, nid, ret;
 
-	si_domain = alloc_domain(DOMAIN_FLAG_STATIC_IDENTITY);
+	si_domain = alloc_domain(IOMMU_DOMAIN_IDENTITY);
 	if (!si_domain)
 		return -EFAULT;
 
 	if (md_domain_init(si_domain, DEFAULT_DOMAIN_ADDRESS_WIDTH)) {
 		domain_exit(si_domain);
+		si_domain = NULL;
 		return -EFAULT;
 	}
 
@@ -2877,6 +2915,9 @@
 
 		if ((iommu_identity_mapping & IDENTMAP_GFX) && IS_GFX_DEVICE(pdev))
 			return IOMMU_DOMAIN_IDENTITY;
+
+		if ((iommu_identity_mapping & IDENTMAP_IPU) && IS_INTEL_IPU(pdev))
+			return IOMMU_DOMAIN_IDENTITY;
 	}
 
 	return 0;
@@ -2979,32 +3020,14 @@
 		/* Now copy the context entry */
 		memcpy(&ce, old_ce + idx, sizeof(ce));
 
-		if (!__context_present(&ce))
+		if (!context_present(&ce))
 			continue;
 
 		did = context_domain_id(&ce);
 		if (did >= 0 && did < cap_ndoms(iommu->cap))
 			set_bit(did, iommu->domain_ids);
 
-		/*
-		 * We need a marker for copied context entries. This
-		 * marker needs to work for the old format as well as
-		 * for extended context entries.
-		 *
-		 * Bit 67 of the context entry is used. In the old
-		 * format this bit is available to software, in the
-		 * extended format it is the PGE bit, but PGE is ignored
-		 * by HW if PASIDs are disabled (and thus still
-		 * available).
-		 *
-		 * So disable PASIDs first and then mark the entry
-		 * copied. This means that we don't copy PASID
-		 * translations from the old kernel, but this is fine as
-		 * faults there are not fatal.
-		 */
-		context_clear_pasid_enable(&ce);
-		context_set_copied(&ce);
-
+		set_context_copied(iommu, bus, devfn);
 		new_ce[idx] = ce;
 	}
 
@@ -3031,8 +3054,8 @@
 	bool new_ext, ext;
 
 	rtaddr_reg = dmar_readq(iommu->reg + DMAR_RTADDR_REG);
-	ext        = !!(rtaddr_reg & DMA_RTADDR_RTT);
-	new_ext    = !!ecap_ecs(iommu->ecap);
+	ext        = !!(rtaddr_reg & DMA_RTADDR_SMT);
+	new_ext    = !!sm_supported(iommu);
 
 	/*
 	 * The RTT bit can only be changed when translation is disabled,
@@ -3043,6 +3066,10 @@
 	if (new_ext != ext)
 		return -EINVAL;
 
+	iommu->copied_tables = bitmap_zalloc(BIT_ULL(16), GFP_KERNEL);
+	if (!iommu->copied_tables)
+		return -ENOMEM;
+
 	old_rt_phys = rtaddr_reg & VTD_PAGE_MASK;
 	if (!old_rt_phys)
 		return -EINVAL;
@@ -3313,6 +3340,9 @@
 	if (!dmar_map_gfx)
 		iommu_identity_mapping |= IDENTMAP_GFX;
 
+	if (!dmar_map_ipu)
+		iommu_identity_mapping |= IDENTMAP_IPU;
+
 	check_tylersburg_isoch();
 
 	ret = si_domain_init(hw_pass_through);
@@ -3364,6 +3394,10 @@
 		disable_dmar_iommu(iommu);
 		free_dmar_iommu(iommu);
 	}
+	if (si_domain) {
+		domain_exit(si_domain);
+		si_domain = NULL;
+	}
 
 	kfree(g_iommus);
 
@@ -3520,13 +3554,6 @@
 	struct intel_iommu *iommu = NULL;
 	unsigned long flag;
 
-	for_each_active_iommu(iommu, drhd) {
-		iommu->iommu_state = kcalloc(MAX_SR_DMAR_REGS, sizeof(u32),
-					     GFP_KERNEL);
-		if (!iommu->iommu_state)
-			goto nomem;
-	}
-
 	iommu_flush_all();
 
 	for_each_active_iommu(iommu, drhd) {
@@ -3546,12 +3573,6 @@
 		raw_spin_unlock_irqrestore(&iommu->register_lock, flag);
 	}
 	return 0;
-
-nomem:
-	for_each_active_iommu(iommu, drhd)
-		kfree(iommu->iommu_state);
-
-	return -ENOMEM;
 }
 
 static void iommu_resume(void)
@@ -3583,9 +3604,6 @@
 
 		raw_spin_unlock_irqrestore(&iommu->register_lock, flag);
 	}
-
-	for_each_active_iommu(iommu, drhd)
-		kfree(iommu->iommu_state);
 }
 
 static struct syscore_ops iommu_syscore_ops = {
@@ -4205,8 +4223,10 @@
 	struct pci_dev *pdev = NULL;
 
 	for_each_pci_dev(pdev)
-		if (pdev->external_facing)
+		if (pdev->external_facing) {
+			pci_dev_put(pdev);
 			return true;
+		}
 
 	return false;
 }
@@ -4377,7 +4397,8 @@
 		 * is likely to be much lower than the overhead of synchronizing
 		 * the virtual and physical IOMMU page-tables.
 		 */
-		if (cap_caching_mode(iommu->cap)) {
+		if (cap_caching_mode(iommu->cap) &&
+		    !first_level_by_default(IOMMU_DOMAIN_DMA)) {
 			pr_info_once("IOMMU batching disallowed due to virtualization\n");
 			iommu_set_dma_strict();
 		}
@@ -4434,8 +4455,10 @@
  */
 static void domain_context_clear(struct device_domain_info *info)
 {
-	if (!info->iommu || !info->dev || !dev_is_pci(info->dev))
+	if (!dev_is_pci(info->dev)) {
+		domain_context_clear_one(info, info->bus, info->devfn);
 		return;
+	}
 
 	pci_for_each_dma_alias(to_pci_dev(info->dev),
 			       &domain_context_clear_one_cb, info);
@@ -4517,7 +4540,7 @@
 	case IOMMU_DOMAIN_DMA:
 	case IOMMU_DOMAIN_DMA_FQ:
 	case IOMMU_DOMAIN_UNMANAGED:
-		dmar_domain = alloc_domain(0);
+		dmar_domain = alloc_domain(type);
 		if (!dmar_domain) {
 			pr_err("Can't allocate dmar_domain\n");
 			return NULL;
@@ -5093,7 +5116,12 @@
 	if (dmar_domain->max_addr == iova + size)
 		dmar_domain->max_addr = iova;
 
-	iommu_iotlb_gather_add_page(domain, gather, iova, size);
+	/*
+	 * We do not use page-selective IOTLB invalidation in flush queue,
+	 * so there is no need to track page and sync iotlb.
+	 */
+	if (!iommu_iotlb_gather_queued(gather))
+		iommu_iotlb_gather_add_page(domain, gather, iova, size);
 
 	return size;
 }
@@ -5367,8 +5395,12 @@
 		return -EINVAL;
 
 	ret = iopf_queue_add_device(iommu->iopf_queue, dev);
-	if (!ret)
-		ret = iommu_register_device_fault_handler(dev, iommu_queue_iopf, dev);
+	if (ret)
+		return ret;
+
+	ret = iommu_register_device_fault_handler(dev, iommu_queue_iopf, dev);
+	if (ret)
+		iopf_queue_remove_device(iommu->iopf_queue, dev);
 
 	return ret;
 }
@@ -5380,8 +5412,12 @@
 	int ret;
 
 	ret = iommu_unregister_device_fault_handler(dev);
-	if (!ret)
-		ret = iopf_queue_remove_device(iommu->iopf_queue, dev);
+	if (ret)
+		return ret;
+
+	ret = iopf_queue_remove_device(iommu->iopf_queue, dev);
+	if (ret)
+		iommu_register_device_fault_handler(dev, iommu_queue_iopf, dev);
 
 	return ret;
 }
@@ -5605,6 +5641,18 @@
 	dmar_map_gfx = 0;
 }
 
+static void quirk_iommu_ipu(struct pci_dev *dev)
+{
+	if (!IS_INTEL_IPU(dev))
+		return;
+
+	if (risky_device(dev))
+		return;
+
+	pci_info(dev, "Passthrough IOMMU for integrated Intel IPU\n");
+	dmar_map_ipu = 0;
+}
+
 /* G4x/GM45 integrated gfx dmar support is totally busted. */
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2a40, quirk_iommu_igfx);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2e00, quirk_iommu_igfx);
@@ -5640,6 +5688,9 @@
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x163A, quirk_iommu_igfx);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x163D, quirk_iommu_igfx);
 
+/* disable IPU dmar support */
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_iommu_ipu);
+
 static void quirk_iommu_rwbf(struct pci_dev *dev)
 {
 	if (risky_device(dev))
@@ -5705,7 +5756,7 @@
 	ver = (dev->device >> 8) & 0xff;
 	if (ver != 0x45 && ver != 0x46 && ver != 0x4c &&
 	    ver != 0x4e && ver != 0x8a && ver != 0x98 &&
-	    ver != 0x9a)
+	    ver != 0x9a && ver != 0xa7 && ver != 0x7d)
 		return;
 
 	if (risky_device(dev))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/irq_remapping.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/irq_remapping.c
@@ -569,9 +569,8 @@
 					    fn, &intel_ir_domain_ops,
 					    iommu);
 	if (!iommu->ir_domain) {
-		irq_domain_free_fwnode(fn);
 		pr_err("IR%d: failed to allocate irqdomain\n", iommu->seq_id);
-		goto out_free_bitmap;
+		goto out_free_fwnode;
 	}
 	iommu->ir_msi_domain =
 		arch_create_remap_msi_irq_domain(iommu->ir_domain,
@@ -595,7 +594,7 @@
 
 		if (dmar_enable_qi(iommu)) {
 			pr_err("Failed to enable queued invalidation\n");
-			goto out_free_bitmap;
+			goto out_free_ir_domain;
 		}
 	}
 
@@ -619,6 +618,14 @@
 
 	return 0;
 
+out_free_ir_domain:
+	if (iommu->ir_msi_domain)
+		irq_domain_remove(iommu->ir_msi_domain);
+	iommu->ir_msi_domain = NULL;
+	irq_domain_remove(iommu->ir_domain);
+	iommu->ir_domain = NULL;
+out_free_fwnode:
+	irq_domain_free_fwnode(fn);
 out_free_bitmap:
 	bitmap_free(bitmap);
 out_free_pages:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/pasid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/pasid.c
@@ -86,54 +86,6 @@
 /*
  * Per device pasid table management:
  */
-static inline void
-device_attach_pasid_table(struct device_domain_info *info,
-			  struct pasid_table *pasid_table)
-{
-	info->pasid_table = pasid_table;
-	list_add(&info->table, &pasid_table->dev);
-}
-
-static inline void
-device_detach_pasid_table(struct device_domain_info *info,
-			  struct pasid_table *pasid_table)
-{
-	info->pasid_table = NULL;
-	list_del(&info->table);
-}
-
-struct pasid_table_opaque {
-	struct pasid_table	**pasid_table;
-	int			segment;
-	int			bus;
-	int			devfn;
-};
-
-static int search_pasid_table(struct device_domain_info *info, void *opaque)
-{
-	struct pasid_table_opaque *data = opaque;
-
-	if (info->iommu->segment == data->segment &&
-	    info->bus == data->bus &&
-	    info->devfn == data->devfn &&
-	    info->pasid_table) {
-		*data->pasid_table = info->pasid_table;
-		return 1;
-	}
-
-	return 0;
-}
-
-static int get_alias_pasid_table(struct pci_dev *pdev, u16 alias, void *opaque)
-{
-	struct pasid_table_opaque *data = opaque;
-
-	data->segment = pci_domain_nr(pdev->bus);
-	data->bus = PCI_BUS_NUM(alias);
-	data->devfn = alias & 0xff;
-
-	return for_each_device_domain(&search_pasid_table, data);
-}
 
 /*
  * Allocate a pasid table for @dev. It should be called in a
@@ -143,28 +95,18 @@
 {
 	struct device_domain_info *info;
 	struct pasid_table *pasid_table;
-	struct pasid_table_opaque data;
 	struct page *pages;
 	u32 max_pasid = 0;
-	int ret, order;
-	int size;
+	int order, size;
 
 	might_sleep();
 	info = get_domain_info(dev);
 	if (WARN_ON(!info || !dev_is_pci(dev) || info->pasid_table))
 		return -EINVAL;
 
-	/* DMA alias device already has a pasid table, use it: */
-	data.pasid_table = &pasid_table;
-	ret = pci_for_each_dma_alias(to_pci_dev(dev),
-				     &get_alias_pasid_table, &data);
-	if (ret)
-		goto attach_out;
-
 	pasid_table = kzalloc(sizeof(*pasid_table), GFP_KERNEL);
 	if (!pasid_table)
 		return -ENOMEM;
-	INIT_LIST_HEAD(&pasid_table->dev);
 
 	if (info->pasid_supported)
 		max_pasid = min_t(u32, pci_max_pasids(to_pci_dev(dev)),
@@ -182,9 +124,10 @@
 	pasid_table->table = page_address(pages);
 	pasid_table->order = order;
 	pasid_table->max_pasid = 1 << (order + PAGE_SHIFT + 3);
+	info->pasid_table = pasid_table;
 
-attach_out:
-	device_attach_pasid_table(info, pasid_table);
+	if (!ecap_coherent(info->iommu->ecap))
+		clflush_cache_range(pasid_table->table, (1 << order) * PAGE_SIZE);
 
 	return 0;
 }
@@ -202,10 +145,7 @@
 		return;
 
 	pasid_table = info->pasid_table;
-	device_detach_pasid_table(info, pasid_table);
-
-	if (!list_empty(&pasid_table->dev))
-		return;
+	info->pasid_table = NULL;
 
 	/* Free scalable mode PASID directory tables: */
 	dir = pasid_table->table;
@@ -276,6 +216,10 @@
 			free_pgtable_page(entries);
 			goto retry;
 		}
+		if (!ecap_coherent(info->iommu->ecap)) {
+			clflush_cache_range(entries, VTD_PAGE_SIZE);
+			clflush_cache_range(&dir[dir_index].val, sizeof(*dir));
+		}
 	}
 
 	return &entries[index];
@@ -426,6 +370,16 @@
 }
 
 /*
+ * Setup No Execute Enable bit (Bit 133) of a scalable mode PASID
+ * entry. It is required when XD bit of the first level page table
+ * entry is about to be set.
+ */
+static inline void pasid_set_nxe(struct pasid_entry *pe)
+{
+	pasid_set_bits(&pe->val[2], 1 << 5, 1 << 5);
+}
+
+/*
  * Setup the Page Snoop (PGSNP) field (Bit 88) of a scalable mode
  * PASID entry.
  */
@@ -491,6 +445,9 @@
 	if (!info || !info->ats_enabled)
 		return;
 
+	if (pci_dev_is_disconnected(to_pci_dev(dev)))
+		return;
+
 	sid = info->bus << 8 | info->devfn;
 	qdep = info->ats_qdep;
 	pfsid = info->pfsid;
@@ -631,6 +588,7 @@
 	pasid_set_domain_id(pte, did);
 	pasid_set_address_width(pte, iommu->agaw);
 	pasid_set_page_snoop(pte, !!ecap_smpwc(iommu->ecap));
+	pasid_set_nxe(pte);
 
 	/* Setup Present and PASID Granular Transfer Type: */
 	pasid_set_translation_type(pte, PASID_ENTRY_PGTT_FL_ONLY);
@@ -717,7 +675,7 @@
 	 * Since it is a second level only translation setup, we should
 	 * set SRE bit as well (addresses are expected to be GPAs).
 	 */
-	if (pasid != PASID_RID2PASID)
+	if (pasid != PASID_RID2PASID && ecap_srs(iommu->ecap))
 		pasid_set_sre(pte);
 	pasid_set_present(pte);
 	pasid_flush_caches(iommu, pte, pasid, did);
@@ -756,7 +714,8 @@
 	 * We should set SRE bit as well since the addresses are expected
 	 * to be GPAs.
 	 */
-	pasid_set_sre(pte);
+	if (ecap_srs(iommu->ecap))
+		pasid_set_sre(pte);
 	pasid_set_present(pte);
 	pasid_flush_caches(iommu, pte, pasid, did);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/pasid.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/pasid.h
@@ -74,7 +74,6 @@
 	void			*table;		/* pasid table pointer */
 	int			order;		/* page order of pasid table */
 	u32			max_pasid;	/* max pasid */
-	struct list_head	dev;		/* device list */
 };
 
 /* Get PRESENT bit of a PASID directory entry. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/intel/svm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/intel/svm.c
@@ -88,7 +88,7 @@
 	struct page *pages;
 	int irq, ret;
 
-	pages = alloc_pages(GFP_KERNEL | __GFP_ZERO, PRQ_ORDER);
+	pages = alloc_pages_node(iommu->node, GFP_KERNEL | __GFP_ZERO, PRQ_ORDER);
 	if (!pages) {
 		pr_warn("IOMMU: %s: Failed to allocate page request queue\n",
 			iommu->name);
@@ -978,6 +978,10 @@
 			goto bad_req;
 		}
 
+		/* Drop Stop Marker message. No need for a response. */
+		if (unlikely(req->lpig && !req->rd_req && !req->wr_req))
+			goto prq_advance;
+
 		if (!svm || svm->pasid != req->pasid) {
 			/*
 			 * It can't go away, because the driver is not permitted
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/io-pgtable-arm-v7s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/io-pgtable-arm-v7s.c
@@ -182,14 +182,8 @@
 		(cfg->quirks & IO_PGTABLE_QUIRK_ARM_MTK_EXT);
 }
 
-static arm_v7s_iopte paddr_to_iopte(phys_addr_t paddr, int lvl,
-				    struct io_pgtable_cfg *cfg)
+static arm_v7s_iopte to_mtk_iopte(phys_addr_t paddr, arm_v7s_iopte pte)
 {
-	arm_v7s_iopte pte = paddr & ARM_V7S_LVL_MASK(lvl);
-
-	if (!arm_v7s_is_mtk_enabled(cfg))
-		return pte;
-
 	if (paddr & BIT_ULL(32))
 		pte |= ARM_V7S_ATTR_MTK_PA_BIT32;
 	if (paddr & BIT_ULL(33))
@@ -199,6 +193,17 @@
 	return pte;
 }
 
+static arm_v7s_iopte paddr_to_iopte(phys_addr_t paddr, int lvl,
+				    struct io_pgtable_cfg *cfg)
+{
+	arm_v7s_iopte pte = paddr & ARM_V7S_LVL_MASK(lvl);
+
+	if (arm_v7s_is_mtk_enabled(cfg))
+		return to_mtk_iopte(paddr, pte);
+
+	return pte;
+}
+
 static phys_addr_t iopte_to_paddr(arm_v7s_iopte pte, int lvl,
 				  struct io_pgtable_cfg *cfg)
 {
@@ -240,19 +245,31 @@
 	dma_addr_t dma;
 	size_t size = ARM_V7S_TABLE_SIZE(lvl, cfg);
 	void *table = NULL;
+	gfp_t gfp_l1;
+
+	/*
+	 * ARM_MTK_TTBR_EXT extend the translation table base support larger
+	 * memory address.
+	 */
+	gfp_l1 = cfg->quirks & IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT ?
+		 GFP_KERNEL : ARM_V7S_TABLE_GFP_DMA;
 
 	if (lvl == 1)
-		table = (void *)__get_free_pages(
-			__GFP_ZERO | ARM_V7S_TABLE_GFP_DMA, get_order(size));
+		table = (void *)__get_free_pages(gfp_l1 | __GFP_ZERO, get_order(size));
 	else if (lvl == 2)
 		table = kmem_cache_zalloc(data->l2_tables, gfp);
+
+	if (!table)
+		return NULL;
+
 	phys = virt_to_phys(table);
-	if (phys != (arm_v7s_iopte)phys) {
+	if (cfg->quirks & IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT ?
+	    phys >= (1ULL << cfg->oas) : phys != (arm_v7s_iopte)phys) {
 		/* Doesn't fit in PTE */
 		dev_err(dev, "Page table does not fit in PTE: %pa", &phys);
 		goto out_free;
 	}
-	if (table && !cfg->coherent_walk) {
+	if (!cfg->coherent_walk) {
 		dma = dma_map_single(dev, table, size, DMA_TO_DEVICE);
 		if (dma_mapping_error(dev, dma))
 			goto out_free;
@@ -453,9 +470,14 @@
 					   arm_v7s_iopte curr,
 					   struct io_pgtable_cfg *cfg)
 {
+	phys_addr_t phys = virt_to_phys(table);
 	arm_v7s_iopte old, new;
 
-	new = virt_to_phys(table) | ARM_V7S_PTE_TYPE_TABLE;
+	new = phys | ARM_V7S_PTE_TYPE_TABLE;
+
+	if (cfg->quirks & IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT)
+		new = to_mtk_iopte(phys, new);
+
 	if (cfg->quirks & IO_PGTABLE_QUIRK_ARM_NS)
 		new |= ARM_V7S_ATTR_NS_TABLE;
 
@@ -775,6 +797,8 @@
 						void *cookie)
 {
 	struct arm_v7s_io_pgtable *data;
+	slab_flags_t slab_flag;
+	phys_addr_t paddr;
 
 	if (cfg->ias > (arm_v7s_is_mtk_enabled(cfg) ? 34 : ARM_V7S_ADDR_BITS))
 		return NULL;
@@ -784,7 +808,8 @@
 
 	if (cfg->quirks & ~(IO_PGTABLE_QUIRK_ARM_NS |
 			    IO_PGTABLE_QUIRK_NO_PERMS |
-			    IO_PGTABLE_QUIRK_ARM_MTK_EXT))
+			    IO_PGTABLE_QUIRK_ARM_MTK_EXT |
+			    IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT))
 		return NULL;
 
 	/* If ARM_MTK_4GB is enabled, the NO_PERMS is also expected. */
@@ -792,15 +817,27 @@
 	    !(cfg->quirks & IO_PGTABLE_QUIRK_NO_PERMS))
 			return NULL;
 
+	if ((cfg->quirks & IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT) &&
+	    !arm_v7s_is_mtk_enabled(cfg))
+		return NULL;
+
 	data = kmalloc(sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return NULL;
 
 	spin_lock_init(&data->split_lock);
+
+	/*
+	 * ARM_MTK_TTBR_EXT extend the translation table base support larger
+	 * memory address.
+	 */
+	slab_flag = cfg->quirks & IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT ?
+		    0 : ARM_V7S_TABLE_SLAB_FLAGS;
+
 	data->l2_tables = kmem_cache_create("io-pgtable_armv7s_l2",
 					    ARM_V7S_TABLE_SIZE(2, cfg),
 					    ARM_V7S_TABLE_SIZE(2, cfg),
-					    ARM_V7S_TABLE_SLAB_FLAGS, NULL);
+					    slab_flag, NULL);
 	if (!data->l2_tables)
 		goto out_free_data;
 
@@ -846,12 +883,16 @@
 	wmb();
 
 	/* TTBR */
-	cfg->arm_v7s_cfg.ttbr = virt_to_phys(data->pgd) | ARM_V7S_TTBR_S |
-				(cfg->coherent_walk ? (ARM_V7S_TTBR_NOS |
-				 ARM_V7S_TTBR_IRGN_ATTR(ARM_V7S_RGN_WBWA) |
-				 ARM_V7S_TTBR_ORGN_ATTR(ARM_V7S_RGN_WBWA)) :
-				(ARM_V7S_TTBR_IRGN_ATTR(ARM_V7S_RGN_NC) |
-				 ARM_V7S_TTBR_ORGN_ATTR(ARM_V7S_RGN_NC)));
+	paddr = virt_to_phys(data->pgd);
+	if (arm_v7s_is_mtk_enabled(cfg))
+		cfg->arm_v7s_cfg.ttbr = paddr | upper_32_bits(paddr);
+	else
+		cfg->arm_v7s_cfg.ttbr = paddr | ARM_V7S_TTBR_S |
+					(cfg->coherent_walk ? (ARM_V7S_TTBR_NOS |
+					 ARM_V7S_TTBR_IRGN_ATTR(ARM_V7S_RGN_WBWA) |
+					 ARM_V7S_TTBR_ORGN_ATTR(ARM_V7S_RGN_WBWA)) :
+					(ARM_V7S_TTBR_IRGN_ATTR(ARM_V7S_RGN_NC) |
+					 ARM_V7S_TTBR_ORGN_ATTR(ARM_V7S_RGN_NC)));
 	return &data->iop;
 
 out_free_data:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/io-pgtable-arm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/io-pgtable-arm.c
@@ -183,6 +183,18 @@
 	return (paddr | (paddr << (48 - 12))) & (ARM_LPAE_PTE_ADDR_MASK << 4);
 }
 
+/*
+ * Convert an index returned by ARM_LPAE_PGD_IDX(), which can point into
+ * a concatenated PGD, into the maximum number of entries that can be
+ * mapped in the same table page.
+ */
+static inline int arm_lpae_max_entries(int i, struct arm_lpae_io_pgtable *data)
+{
+	int ptes_per_table = ARM_LPAE_PTES_PER_TABLE(data);
+
+	return ptes_per_table - (i & (ptes_per_table - 1));
+}
+
 static bool selftest_running = false;
 
 static dma_addr_t __arm_lpae_dma_addr(void *pages)
@@ -315,11 +327,12 @@
 static arm_lpae_iopte arm_lpae_install_table(arm_lpae_iopte *table,
 					     arm_lpae_iopte *ptep,
 					     arm_lpae_iopte curr,
-					     struct io_pgtable_cfg *cfg)
+					     struct arm_lpae_io_pgtable *data)
 {
 	arm_lpae_iopte old, new;
+	struct io_pgtable_cfg *cfg = &data->iop.cfg;
 
-	new = __pa(table) | ARM_LPAE_PTE_TYPE_TABLE;
+	new = paddr_to_iopte(__pa(table), data) | ARM_LPAE_PTE_TYPE_TABLE;
 	if (cfg->quirks & IO_PGTABLE_QUIRK_ARM_NS)
 		new |= ARM_LPAE_PTE_NSTABLE;
 
@@ -360,7 +373,7 @@
 
 	/* If we can install a leaf entry at this level, then do so */
 	if (size == block_size) {
-		max_entries = ARM_LPAE_PTES_PER_TABLE(data) - map_idx_start;
+		max_entries = arm_lpae_max_entries(map_idx_start, data);
 		num_entries = min_t(int, pgcount, max_entries);
 		ret = arm_lpae_init_pte(data, iova, paddr, prot, lvl, num_entries, ptep);
 		if (!ret && mapped)
@@ -380,7 +393,7 @@
 		if (!cptep)
 			return -ENOMEM;
 
-		pte = arm_lpae_install_table(cptep, ptep, 0, cfg);
+		pte = arm_lpae_install_table(cptep, ptep, 0, data);
 		if (pte)
 			__arm_lpae_free_pages(cptep, tblsz, cfg);
 	} else if (!cfg->coherent_walk && !(pte & ARM_LPAE_PTE_SW_SYNC)) {
@@ -577,7 +590,7 @@
 
 	if (size == split_sz) {
 		unmap_idx_start = ARM_LPAE_LVL_IDX(iova, lvl, data);
-		max_entries = ptes_per_table - unmap_idx_start;
+		max_entries = arm_lpae_max_entries(unmap_idx_start, data);
 		num_entries = min_t(int, pgcount, max_entries);
 	}
 
@@ -592,7 +605,7 @@
 		__arm_lpae_init_pte(data, blk_paddr, pte, lvl, 1, &tablep[i]);
 	}
 
-	pte = arm_lpae_install_table(tablep, ptep, blk_pte, cfg);
+	pte = arm_lpae_install_table(tablep, ptep, blk_pte, data);
 	if (pte != blk_pte) {
 		__arm_lpae_free_pages(tablep, tablesz, cfg);
 		/*
@@ -635,7 +648,7 @@
 
 	/* If the size matches this level, we're in the right place */
 	if (size == ARM_LPAE_BLOCK_SIZE(lvl, data)) {
-		max_entries = ARM_LPAE_PTES_PER_TABLE(data) - unmap_idx_start;
+		max_entries = arm_lpae_max_entries(unmap_idx_start, data);
 		num_entries = min_t(int, pgcount, max_entries);
 
 		while (i < num_entries) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/iommu.c
@@ -206,9 +206,14 @@
 
 static void dev_iommu_free(struct device *dev)
 {
-	iommu_fwspec_free(dev);
-	kfree(dev->iommu);
+	struct dev_iommu *param = dev->iommu;
+
 	dev->iommu = NULL;
+	if (param->fwspec) {
+		fwnode_handle_put(param->fwspec->iommu_fwnode);
+		kfree(param->fwspec);
+	}
+	kfree(param);
 }
 
 static int __iommu_probe_device(struct device *dev, struct list_head *group_list)
@@ -287,11 +292,11 @@
 	 */
 	mutex_lock(&group->mutex);
 	iommu_alloc_default_domain(group, dev);
-	mutex_unlock(&group->mutex);
 
 	if (group->default_domain) {
 		ret = __iommu_attach_device(group->default_domain, dev);
 		if (ret) {
+			mutex_unlock(&group->mutex);
 			iommu_group_put(group);
 			goto err_release;
 		}
@@ -299,6 +304,7 @@
 
 	iommu_create_device_direct_mappings(group, dev);
 
+	mutex_unlock(&group->mutex);
 	iommu_group_put(group);
 
 	if (ops->probe_finalize)
@@ -650,12 +656,16 @@
 
 	ret = iommu_group_create_file(group,
 				      &iommu_group_attr_reserved_regions);
-	if (ret)
+	if (ret) {
+		kobject_put(group->devices_kobj);
 		return ERR_PTR(ret);
+	}
 
 	ret = iommu_group_create_file(group, &iommu_group_attr_type);
-	if (ret)
+	if (ret) {
+		kobject_put(group->devices_kobj);
 		return ERR_PTR(ret);
+	}
 
 	pr_debug("Allocated group %d\n", group->id);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/iova.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/iova.c
@@ -27,6 +27,11 @@
 static void fq_destroy_all_entries(struct iova_domain *iovad);
 static void fq_flush_timeout(struct timer_list *t);
 
+unsigned long iova_rcache_range(void)
+{
+	return PAGE_SIZE << (IOVA_RANGE_CACHE_MAX_SIZE - 1);
+}
+
 static int iova_cpuhp_dead(unsigned int cpu, struct hlist_node *node)
 {
 	struct iova_domain *iovad;
@@ -83,8 +88,7 @@
 	if (!has_iova_flush_queue(iovad))
 		return;
 
-	if (timer_pending(&iovad->fq_timer))
-		del_timer(&iovad->fq_timer);
+	del_timer_sync(&iovad->fq_timer);
 
 	fq_destroy_all_entries(iovad);
 
@@ -155,10 +159,11 @@
 	cached_iova = to_iova(iovad->cached32_node);
 	if (free == cached_iova ||
 	    (free->pfn_hi < iovad->dma_32bit_pfn &&
-	     free->pfn_lo >= cached_iova->pfn_lo)) {
+	     free->pfn_lo >= cached_iova->pfn_lo))
 		iovad->cached32_node = rb_next(&free->node);
+
+	if (free->pfn_lo < iovad->dma_32bit_pfn)
 		iovad->max32_alloc_size = iovad->dma_32bit_pfn;
-	}
 
 	cached_iova = to_iova(iovad->cached_node);
 	if (free->pfn_lo >= cached_iova->pfn_lo)
@@ -252,7 +257,7 @@
 
 	curr = __get_cached_rbnode(iovad, limit_pfn);
 	curr_iova = to_iova(curr);
-	retry_pfn = curr_iova->pfn_hi + 1;
+	retry_pfn = curr_iova->pfn_hi;
 
 retry:
 	do {
@@ -266,7 +271,7 @@
 	if (high_pfn < size || new_pfn < low_pfn) {
 		if (low_pfn == iovad->start_pfn && retry_pfn < limit_pfn) {
 			high_pfn = limit_pfn;
-			low_pfn = retry_pfn;
+			low_pfn = retry_pfn + 1;
 			curr = iova_find_limit(iovad, limit_pfn);
 			curr_iova = to_iova(curr);
 			goto retry;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/ipmmu-vmsa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/ipmmu-vmsa.c
@@ -982,7 +982,9 @@
 	bitmap_zero(mmu->ctx, IPMMU_CTX_MAX);
 	mmu->features = of_device_get_match_data(&pdev->dev);
 	memset(mmu->utlb_ctx, IPMMU_CTX_INVALID, mmu->features->num_utlbs);
-	dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(40));
+	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(40));
+	if (ret)
+		return ret;
 
 	/* Map I/O memory and request IRQ. */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/msm_iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/msm_iommu.c
@@ -615,16 +615,19 @@
 static int qcom_iommu_of_xlate(struct device *dev,
 			       struct of_phandle_args *spec)
 {
-	struct msm_iommu_dev *iommu;
+	struct msm_iommu_dev *iommu = NULL, *iter;
 	unsigned long flags;
 	int ret = 0;
 
 	spin_lock_irqsave(&msm_iommu_lock, flags);
-	list_for_each_entry(iommu, &qcom_iommu_devices, dev_node)
-		if (iommu->dev->of_node == spec->np)
+	list_for_each_entry(iter, &qcom_iommu_devices, dev_node) {
+		if (iter->dev->of_node == spec->np) {
+			iommu = iter;
 			break;
+		}
+	}
 
-	if (!iommu || iommu->dev->of_node != spec->np) {
+	if (!iommu) {
 		ret = -ENODEV;
 		goto fail;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/mtk_iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/mtk_iommu.c
@@ -451,7 +451,7 @@
 static int mtk_iommu_attach_device(struct iommu_domain *domain,
 				   struct device *dev)
 {
-	struct mtk_iommu_data *data = dev_iommu_priv_get(dev);
+	struct mtk_iommu_data *data = dev_iommu_priv_get(dev), *frstdata;
 	struct mtk_iommu_domain *dom = to_mtk_domain(domain);
 	struct device *m4udev = data->dev;
 	int ret, domid;
@@ -461,20 +461,24 @@
 		return domid;
 
 	if (!dom->data) {
-		if (mtk_iommu_domain_finalise(dom, data, domid))
+		/* Data is in the frstdata in sharing pgtable case. */
+		frstdata = mtk_iommu_get_m4u_data();
+
+		if (mtk_iommu_domain_finalise(dom, frstdata, domid))
 			return -ENODEV;
 		dom->data = data;
 	}
 
+	mutex_lock(&data->mutex);
 	if (!data->m4u_dom) { /* Initialize the M4U HW */
 		ret = pm_runtime_resume_and_get(m4udev);
 		if (ret < 0)
-			return ret;
+			goto err_unlock;
 
 		ret = mtk_iommu_hw_init(data);
 		if (ret) {
 			pm_runtime_put(m4udev);
-			return ret;
+			goto err_unlock;
 		}
 		data->m4u_dom = dom;
 		writel(dom->cfg.arm_v7s_cfg.ttbr & MMU_PT_ADDR_MASK,
@@ -482,9 +486,14 @@
 
 		pm_runtime_put(m4udev);
 	}
+	mutex_unlock(&data->mutex);
 
 	mtk_iommu_config(data, dev, true, domid);
 	return 0;
+
+err_unlock:
+	mutex_unlock(&data->mutex);
+	return ret;
 }
 
 static void mtk_iommu_detach_device(struct iommu_domain *domain,
@@ -550,7 +559,9 @@
 	phys_addr_t pa;
 
 	pa = dom->iop->iova_to_phys(dom->iop, iova);
-	if (dom->data->enable_4GB && pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
+	if (IS_ENABLED(CONFIG_PHYS_ADDR_T_64BIT) &&
+	    dom->data->enable_4GB &&
+	    pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
 		pa &= ~BIT_ULL(32);
 
 	return pa;
@@ -560,22 +571,58 @@
 {
 	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
 	struct mtk_iommu_data *data;
+	struct device_link *link;
+	struct device *larbdev;
+	unsigned int larbid, larbidx, i;
 
 	if (!fwspec || fwspec->ops != &mtk_iommu_ops)
 		return ERR_PTR(-ENODEV); /* Not a iommu client device */
 
 	data = dev_iommu_priv_get(dev);
 
+	/*
+	 * Link the consumer device with the smi-larb device(supplier).
+	 * The device that connects with each a larb is a independent HW.
+	 * All the ports in each a device should be in the same larbs.
+	 */
+	larbid = MTK_M4U_TO_LARB(fwspec->ids[0]);
+	if (larbid >= MTK_LARB_NR_MAX)
+		return ERR_PTR(-EINVAL);
+
+	for (i = 1; i < fwspec->num_ids; i++) {
+		larbidx = MTK_M4U_TO_LARB(fwspec->ids[i]);
+		if (larbid != larbidx) {
+			dev_err(dev, "Can only use one larb. Fail@larb%d-%d.\n",
+				larbid, larbidx);
+			return ERR_PTR(-EINVAL);
+		}
+	}
+	larbdev = data->larb_imu[larbid].dev;
+	if (!larbdev)
+		return ERR_PTR(-EINVAL);
+
+	link = device_link_add(dev, larbdev,
+			       DL_FLAG_PM_RUNTIME | DL_FLAG_STATELESS);
+	if (!link)
+		dev_err(dev, "Unable to link %s\n", dev_name(larbdev));
 	return &data->iommu;
 }
 
 static void mtk_iommu_release_device(struct device *dev)
 {
 	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
+	struct mtk_iommu_data *data;
+	struct device *larbdev;
+	unsigned int larbid;
 
 	if (!fwspec || fwspec->ops != &mtk_iommu_ops)
 		return;
 
+	data = dev_iommu_priv_get(dev);
+	larbid = MTK_M4U_TO_LARB(fwspec->ids[0]);
+	larbdev = data->larb_imu[larbid].dev;
+	device_link_remove(dev, larbdev);
+
 	iommu_fwspec_free(dev);
 }
 
@@ -592,6 +639,7 @@
 	if (domid < 0)
 		return ERR_PTR(domid);
 
+	mutex_lock(&data->mutex);
 	group = data->m4u_group[domid];
 	if (!group) {
 		group = iommu_group_alloc();
@@ -600,6 +648,7 @@
 	} else {
 		iommu_group_ref_get(group);
 	}
+	mutex_unlock(&data->mutex);
 	return group;
 }
 
@@ -846,7 +895,7 @@
 		plarbdev = of_find_device_by_node(larbnode);
 		if (!plarbdev) {
 			of_node_put(larbnode);
-			return -EPROBE_DEFER;
+			return -ENODEV;
 		}
 		data->larb_imu[id].dev = &plarbdev->dev;
 
@@ -874,6 +923,7 @@
 	}
 
 	platform_set_drvdata(pdev, data);
+	mutex_init(&data->mutex);
 
 	ret = iommu_device_sysfs_add(&data->iommu, dev, NULL,
 				     "mtk-iommu.%pa", &ioaddr);
@@ -919,10 +969,8 @@
 	iommu_device_sysfs_remove(&data->iommu);
 	iommu_device_unregister(&data->iommu);
 
-	if (iommu_present(&platform_bus_type))
-		bus_set_iommu(&platform_bus_type, NULL);
+	list_del(&data->list);
 
-	clk_disable_unprepare(data->bclk);
 	device_link_remove(data->smicomm_dev, &pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	devm_free_irq(&pdev->dev, data->irq, data);
@@ -1053,6 +1101,7 @@
 	{ .compatible = "mediatek,mt8192-m4u", .data = &mt8192_data},
 	{}
 };
+MODULE_DEVICE_TABLE(of, mtk_iommu_of_ids);
 
 static struct platform_driver mtk_iommu_driver = {
 	.probe	= mtk_iommu_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/mtk_iommu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/mtk_iommu.h
@@ -80,6 +80,8 @@
 
 	struct dma_iommu_mapping	*mapping; /* For mtk_iommu_v1.c */
 
+	struct mutex			mutex; /* Protect m4u_group/m4u_dom above */
+
 	struct list_head		list;
 	struct mtk_smi_larb_iommu	larb_imu[MTK_LARB_NR_MAX];
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/mtk_iommu_v1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/mtk_iommu_v1.c
@@ -80,6 +80,7 @@
 /* MTK generation one iommu HW only support 4K size mapping */
 #define MT2701_IOMMU_PAGE_SHIFT			12
 #define MT2701_IOMMU_PAGE_SIZE			(1UL << MT2701_IOMMU_PAGE_SHIFT)
+#define MT2701_LARB_NR_MAX			3
 
 /*
  * MTK m4u support 4GB iova address space, and only support 4K page
@@ -423,7 +424,18 @@
 	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
 	struct of_phandle_args iommu_spec;
 	struct mtk_iommu_data *data;
-	int err, idx = 0;
+	int err, idx = 0, larbid, larbidx;
+	struct device_link *link;
+	struct device *larbdev;
+
+	/*
+	 * In the deferred case, free the existed fwspec.
+	 * Always initialize the fwspec internally.
+	 */
+	if (fwspec) {
+		iommu_fwspec_free(dev);
+		fwspec = dev_iommu_fwspec_get(dev);
+	}
 
 	while (!of_parse_phandle_with_args(dev->of_node, "iommus",
 					   "#iommu-cells",
@@ -444,6 +456,29 @@
 
 	data = dev_iommu_priv_get(dev);
 
+	/* Link the consumer device with the smi-larb device(supplier) */
+	larbid = mt2701_m4u_to_larb(fwspec->ids[0]);
+	if (larbid >= MT2701_LARB_NR_MAX)
+		return ERR_PTR(-EINVAL);
+
+	for (idx = 1; idx < fwspec->num_ids; idx++) {
+		larbidx = mt2701_m4u_to_larb(fwspec->ids[idx]);
+		if (larbid != larbidx) {
+			dev_err(dev, "Can only use one larb. Fail@larb%d-%d.\n",
+				larbid, larbidx);
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	larbdev = data->larb_imu[larbid].dev;
+	if (!larbdev)
+		return ERR_PTR(-EINVAL);
+
+	link = device_link_add(dev, larbdev,
+			       DL_FLAG_PM_RUNTIME | DL_FLAG_STATELESS);
+	if (!link)
+		dev_err(dev, "Unable to link %s\n", dev_name(larbdev));
+
 	return &data->iommu;
 }
 
@@ -464,10 +499,18 @@
 static void mtk_iommu_release_device(struct device *dev)
 {
 	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
+	struct mtk_iommu_data *data;
+	struct device *larbdev;
+	unsigned int larbid;
 
 	if (!fwspec || fwspec->ops != &mtk_iommu_ops)
 		return;
 
+	data = dev_iommu_priv_get(dev);
+	larbid = mt2701_m4u_to_larb(fwspec->ids[0]);
+	larbdev = data->larb_imu[larbid].dev;
+	device_link_remove(dev, larbdev);
+
 	iommu_fwspec_free(dev);
 }
 
@@ -533,6 +576,7 @@
 	{ .compatible = "mediatek,mt2701-m4u", },
 	{}
 };
+MODULE_DEVICE_TABLE(of, mtk_iommu_of_ids);
 
 static const struct component_master_ops mtk_iommu_com_ops = {
 	.bind		= mtk_iommu_bind,
@@ -595,7 +639,7 @@
 		plarbdev = of_find_device_by_node(larbnode);
 		if (!plarbdev) {
 			of_node_put(larbnode);
-			return -EPROBE_DEFER;
+			return -ENODEV;
 		}
 		data->larb_imu[i].dev = &plarbdev->dev;
 
@@ -612,7 +656,7 @@
 	ret = iommu_device_sysfs_add(&data->iommu, &pdev->dev, NULL,
 				     dev_name(&pdev->dev));
 	if (ret)
-		return ret;
+		goto out_clk_unprepare;
 
 	ret = iommu_device_register(&data->iommu, &mtk_iommu_ops, dev);
 	if (ret)
@@ -635,6 +679,8 @@
 	iommu_device_unregister(&data->iommu);
 out_sysfs_remove:
 	iommu_device_sysfs_remove(&data->iommu);
+out_clk_unprepare:
+	clk_disable_unprepare(data->bclk);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/omap-iommu-debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/omap-iommu-debug.c
@@ -32,12 +32,12 @@
 		ssize_t bytes;						\
 		const char *str = "%20s: %08x\n";			\
 		const int maxcol = 32;					\
-		bytes = snprintf(p, maxcol, str, __stringify(name),	\
+		if (len < maxcol)					\
+			goto out;					\
+		bytes = scnprintf(p, maxcol, str, __stringify(name),	\
 				 iommu_read_reg(obj, MMU_##name));	\
 		p += bytes;						\
 		len -= bytes;						\
-		if (len < maxcol)					\
-			goto out;					\
 	} while (0)
 
 static ssize_t
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/omap-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/omap-iommu.c
@@ -1661,7 +1661,7 @@
 	num_iommus = of_property_count_elems_of_size(dev->of_node, "iommus",
 						     sizeof(phandle));
 	if (num_iommus < 0)
-		return 0;
+		return ERR_PTR(-ENODEV);
 
 	arch_data = kcalloc(num_iommus + 1, sizeof(*arch_data), GFP_KERNEL);
 	if (!arch_data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/rockchip-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/rockchip-iommu.c
@@ -98,8 +98,6 @@
 	phys_addr_t (*pt_address)(u32 dte);
 	u32 (*mk_dtentries)(dma_addr_t pt_dma);
 	u32 (*mk_ptentries)(phys_addr_t page, int prot);
-	phys_addr_t (*dte_addr_phys)(u32 addr);
-	u32 (*dma_addr_dte)(dma_addr_t dt_dma);
 	u64 dma_bit_mask;
 };
 
@@ -200,8 +198,8 @@
 #define DTE_HI_MASK2	GENMASK(7, 4)
 #define DTE_HI_SHIFT1	24 /* shift bit 8 to bit 32 */
 #define DTE_HI_SHIFT2	32 /* shift bit 4 to bit 36 */
-#define PAGE_DESC_HI_MASK1	GENMASK_ULL(39, 36)
-#define PAGE_DESC_HI_MASK2	GENMASK_ULL(35, 32)
+#define PAGE_DESC_HI_MASK1	GENMASK_ULL(35, 32)
+#define PAGE_DESC_HI_MASK2	GENMASK_ULL(39, 36)
 
 static inline phys_addr_t rk_dte_pt_address_v2(u32 dte)
 {
@@ -277,22 +275,20 @@
 /*
  * In v2:
  * 31:12 - Page address bit 31:0
- *  11:9 - Page address bit 34:32
- *   8:4 - Page address bit 39:35
+ * 11: 8 - Page address bit 35:32
+ *  7: 4 - Page address bit 39:36
  *     3 - Security
- *     2 - Readable
- *     1 - Writable
+ *     2 - Writable
+ *     1 - Readable
  *     0 - 1 if Page @ Page address is valid
  */
-#define RK_PTE_PAGE_READABLE_V2      BIT(2)
-#define RK_PTE_PAGE_WRITABLE_V2      BIT(1)
 
 static u32 rk_mk_pte_v2(phys_addr_t page, int prot)
 {
 	u32 flags = 0;
 
-	flags |= (prot & IOMMU_READ) ? RK_PTE_PAGE_READABLE_V2 : 0;
-	flags |= (prot & IOMMU_WRITE) ? RK_PTE_PAGE_WRITABLE_V2 : 0;
+	flags |= (prot & IOMMU_READ) ? RK_PTE_PAGE_READABLE : 0;
+	flags |= (prot & IOMMU_WRITE) ? RK_PTE_PAGE_WRITABLE : 0;
 
 	return rk_mk_dte_v2(page) | flags;
 }
@@ -507,7 +503,7 @@
 
 	/*
 	 * Check if register DTE_ADDR is working by writing DTE_ADDR_DUMMY
-	 * and verifying that upper 5 nybbles are read back.
+	 * and verifying that upper 5 (v1) or 7 (v2) nybbles are read back.
 	 */
 	for (i = 0; i < iommu->num_mmu; i++) {
 		dte_addr = rk_ops->pt_address(DTE_ADDR_DUMMY);
@@ -532,33 +528,6 @@
 	return 0;
 }
 
-static inline phys_addr_t rk_dte_addr_phys(u32 addr)
-{
-	return (phys_addr_t)addr;
-}
-
-static inline u32 rk_dma_addr_dte(dma_addr_t dt_dma)
-{
-	return dt_dma;
-}
-
-#define DT_HI_MASK GENMASK_ULL(39, 32)
-#define DTE_BASE_HI_MASK GENMASK(11, 4)
-#define DT_SHIFT   28
-
-static inline phys_addr_t rk_dte_addr_phys_v2(u32 addr)
-{
-	u64 addr64 = addr;
-	return (phys_addr_t)(addr64 & RK_DTE_PT_ADDRESS_MASK) |
-	       ((addr64 & DTE_BASE_HI_MASK) << DT_SHIFT);
-}
-
-static inline u32 rk_dma_addr_dte_v2(dma_addr_t dt_dma)
-{
-	return (dt_dma & RK_DTE_PT_ADDRESS_MASK) |
-	       ((dt_dma & DT_HI_MASK) >> DT_SHIFT);
-}
-
 static void log_iova(struct rk_iommu *iommu, int index, dma_addr_t iova)
 {
 	void __iomem *base = iommu->bases[index];
@@ -578,7 +547,7 @@
 	page_offset = rk_iova_page_offset(iova);
 
 	mmu_dte_addr = rk_iommu_read(base, RK_MMU_DTE_ADDR);
-	mmu_dte_addr_phys = rk_ops->dte_addr_phys(mmu_dte_addr);
+	mmu_dte_addr_phys = rk_ops->pt_address(mmu_dte_addr);
 
 	dte_addr_phys = mmu_dte_addr_phys + (4 * dte_index);
 	dte_addr = phys_to_virt(dte_addr_phys);
@@ -968,7 +937,7 @@
 
 	for (i = 0; i < iommu->num_mmu; i++) {
 		rk_iommu_write(iommu->bases[i], RK_MMU_DTE_ADDR,
-			       rk_ops->dma_addr_dte(rk_domain->dt_dma));
+			       rk_ops->mk_dtentries(rk_domain->dt_dma));
 		rk_iommu_base_command(iommu->bases[i], RK_MMU_CMD_ZAP_CACHE);
 		rk_iommu_write(iommu->bases[i], RK_MMU_INT_MASK, RK_MMU_IRQ_MASK);
 	}
@@ -1305,20 +1274,22 @@
 	for (i = 0; i < iommu->num_irq; i++) {
 		int irq = platform_get_irq(pdev, i);
 
-		if (irq < 0)
-			return irq;
+		if (irq < 0) {
+			err = irq;
+			goto err_pm_disable;
+		}
 
 		err = devm_request_irq(iommu->dev, irq, rk_iommu_irq,
 				       IRQF_SHARED, dev_name(dev), iommu);
-		if (err) {
-			pm_runtime_disable(dev);
-			goto err_remove_sysfs;
-		}
+		if (err)
+			goto err_pm_disable;
 	}
 
 	dma_set_mask_and_coherent(dev, rk_ops->dma_bit_mask);
 
 	return 0;
+err_pm_disable:
+	pm_runtime_disable(dev);
 err_remove_sysfs:
 	iommu_device_sysfs_remove(&iommu->iommu);
 err_put_group:
@@ -1373,8 +1344,6 @@
 	.pt_address = &rk_dte_pt_address,
 	.mk_dtentries = &rk_mk_dte,
 	.mk_ptentries = &rk_mk_pte,
-	.dte_addr_phys = &rk_dte_addr_phys,
-	.dma_addr_dte = &rk_dma_addr_dte,
 	.dma_bit_mask = DMA_BIT_MASK(32),
 };
 
@@ -1382,8 +1351,6 @@
 	.pt_address = &rk_dte_pt_address_v2,
 	.mk_dtentries = &rk_mk_dte_v2,
 	.mk_ptentries = &rk_mk_pte_v2,
-	.dte_addr_phys = &rk_dte_addr_phys_v2,
-	.dma_addr_dte = &rk_dma_addr_dte_v2,
 	.dma_bit_mask = DMA_BIT_MASK(40),
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/sprd-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/sprd-iommu.c
@@ -147,17 +147,11 @@
 
 	dom->domain.geometry.aperture_start = 0;
 	dom->domain.geometry.aperture_end = SZ_256M - 1;
+	dom->domain.geometry.force_aperture = true;
 
 	return &dom->domain;
 }
 
-static void sprd_iommu_domain_free(struct iommu_domain *domain)
-{
-	struct sprd_iommu_domain *dom = to_sprd_domain(domain);
-
-	kfree(dom);
-}
-
 static void sprd_iommu_first_vpn(struct sprd_iommu_domain *dom)
 {
 	struct sprd_iommu_device *sdev = dom->sdev;
@@ -230,6 +224,28 @@
 	sprd_iommu_update_bits(sdev, reg_cfg, mask, 0, val);
 }
 
+static void sprd_iommu_cleanup(struct sprd_iommu_domain *dom)
+{
+	size_t pgt_size;
+
+	/* Nothing need to do if the domain hasn't been attached */
+	if (!dom->sdev)
+		return;
+
+	pgt_size = sprd_iommu_pgt_size(&dom->domain);
+	dma_free_coherent(dom->sdev->dev, pgt_size, dom->pgt_va, dom->pgt_pa);
+	sprd_iommu_hw_en(dom->sdev, false);
+	dom->sdev = NULL;
+}
+
+static void sprd_iommu_domain_free(struct iommu_domain *domain)
+{
+	struct sprd_iommu_domain *dom = to_sprd_domain(domain);
+
+	sprd_iommu_cleanup(dom);
+	kfree(dom);
+}
+
 static int sprd_iommu_attach_device(struct iommu_domain *domain,
 				    struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/sun50i-iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/sun50i-iommu.c
@@ -27,6 +27,7 @@
 #include <linux/types.h>
 
 #define IOMMU_RESET_REG			0x010
+#define IOMMU_RESET_RELEASE_ALL			0xffffffff
 #define IOMMU_ENABLE_REG		0x020
 #define IOMMU_ENABLE_ENABLE			BIT(0)
 
@@ -270,7 +271,7 @@
 	enum sun50i_iommu_aci aci;
 	u32 flags = 0;
 
-	if (prot & (IOMMU_READ | IOMMU_WRITE))
+	if ((prot & (IOMMU_READ | IOMMU_WRITE)) == (IOMMU_READ | IOMMU_WRITE))
 		aci = SUN50I_IOMMU_ACI_RD_WR;
 	else if (prot & IOMMU_READ)
 		aci = SUN50I_IOMMU_ACI_RD;
@@ -378,6 +379,7 @@
 		    IOMMU_TLB_PREFETCH_MASTER_ENABLE(3) |
 		    IOMMU_TLB_PREFETCH_MASTER_ENABLE(4) |
 		    IOMMU_TLB_PREFETCH_MASTER_ENABLE(5));
+	iommu_write(iommu, IOMMU_BYPASS_REG, 0);
 	iommu_write(iommu, IOMMU_INT_ENABLE_REG, IOMMU_INT_MASK);
 	iommu_write(iommu, IOMMU_DM_AUT_CTRL_REG(SUN50I_IOMMU_ACI_NONE),
 		    IOMMU_DM_AUT_CTRL_RD_UNAVAIL(SUN50I_IOMMU_ACI_NONE, 0) |
@@ -511,7 +513,7 @@
 		sun50i_iommu_free_page_table(iommu, drop_pt);
 	}
 
-	sun50i_table_flush(sun50i_domain, page_table, PT_SIZE);
+	sun50i_table_flush(sun50i_domain, page_table, NUM_PT_ENTRIES);
 	sun50i_table_flush(sun50i_domain, dte_addr, 1);
 
 	return page_table;
@@ -601,7 +603,6 @@
 	struct sun50i_iommu_domain *sun50i_domain;
 
 	if (type != IOMMU_DOMAIN_DMA &&
-	    type != IOMMU_DOMAIN_IDENTITY &&
 	    type != IOMMU_DOMAIN_UNMANAGED)
 		return NULL;
 
@@ -869,8 +870,8 @@
 
 static irqreturn_t sun50i_iommu_irq(int irq, void *dev_id)
 {
+	u32 status, l1_status, l2_status, resets;
 	struct sun50i_iommu *iommu = dev_id;
-	u32 status;
 
 	spin_lock(&iommu->iommu_lock);
 
@@ -880,6 +881,9 @@
 		return IRQ_NONE;
 	}
 
+	l1_status = iommu_read(iommu, IOMMU_L1PG_INT_REG);
+	l2_status = iommu_read(iommu, IOMMU_L2PG_INT_REG);
+
 	if (status & IOMMU_INT_INVALID_L2PG)
 		sun50i_iommu_handle_pt_irq(iommu,
 					    IOMMU_INT_ERR_ADDR_L2_REG,
@@ -893,8 +897,9 @@
 
 	iommu_write(iommu, IOMMU_INT_CLR_REG, status);
 
-	iommu_write(iommu, IOMMU_RESET_REG, ~status);
-	iommu_write(iommu, IOMMU_RESET_REG, status);
+	resets = (status | l1_status | l2_status) & IOMMU_INT_MASTER_MASK;
+	iommu_write(iommu, IOMMU_RESET_REG, ~resets);
+	iommu_write(iommu, IOMMU_RESET_REG, IOMMU_RESET_RELEASE_ALL);
 
 	spin_unlock(&iommu->iommu_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/iommu/tegra-smmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/iommu/tegra-smmu.c
@@ -808,8 +808,10 @@
 		return NULL;
 
 	mc = platform_get_drvdata(pdev);
-	if (!mc)
+	if (!mc) {
+		put_device(&pdev->dev);
 		return NULL;
+	}
 
 	return mc->smmu;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/Kconfig
@@ -171,7 +171,7 @@
 config IRQ_MIPS_CPU
 	bool
 	select GENERIC_IRQ_CHIP
-	select GENERIC_IRQ_IPI if SYS_SUPPORTS_MULTITHREADING
+	select GENERIC_IRQ_IPI if SMP && SYS_SUPPORTS_MULTITHREADING
 	select IRQ_DOMAIN
 	select GENERIC_IRQ_EFFECTIVE_AFF_MASK
 
@@ -287,6 +287,13 @@
 	  This is used as a primary controller with MicroBlaze and can also
 	  be used as a secondary chained controller on other platforms.
 
+config IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+	bool "IRQCHIP Xilinx Intc driver module support (experimental)"
+	depends on XILINX_INTC
+	help
+	  Enable support to load irqchip driver as a module as part of DT overlay.
+	  This is currently supported for XIlinx INTC irqchip driver.
+
 config IRQ_CROSSBAR
 	bool
 	help
@@ -304,7 +311,8 @@
 
 config MIPS_GIC
 	bool
-	select GENERIC_IRQ_IPI
+	select GENERIC_IRQ_IPI if SMP
+	select IRQ_DOMAIN_HIERARCHY
 	select MIPS_CM
 
 config INGENIC_IRQ
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-alpine-msi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-alpine-msi.c
@@ -165,7 +165,7 @@
 	return 0;
 
 err_sgi:
-	irq_domain_free_irqs_parent(domain, virq, i - 1);
+	irq_domain_free_irqs_parent(domain, virq, i);
 	alpine_msix_free_sgi(priv, sgi, nr_irqs);
 	return err;
 }
@@ -199,6 +199,7 @@
 	}
 
 	gic_domain = irq_find_host(gic_node);
+	of_node_put(gic_node);
 	if (!gic_domain) {
 		pr_err("Failed to find the GIC domain\n");
 		return -ENXIO;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-armada-370-xp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-armada-370-xp.c
@@ -232,16 +232,12 @@
 	int hwirq, i;
 
 	mutex_lock(&msi_used_lock);
+	hwirq = bitmap_find_free_region(msi_used, PCI_MSI_DOORBELL_NR,
+					order_base_2(nr_irqs));
+	mutex_unlock(&msi_used_lock);
 
-	hwirq = bitmap_find_next_zero_area(msi_used, PCI_MSI_DOORBELL_NR,
-					   0, nr_irqs, 0);
-	if (hwirq >= PCI_MSI_DOORBELL_NR) {
-		mutex_unlock(&msi_used_lock);
+	if (hwirq < 0)
 		return -ENOSPC;
-	}
-
-	bitmap_set(msi_used, hwirq, nr_irqs);
-	mutex_unlock(&msi_used_lock);
 
 	for (i = 0; i < nr_irqs; i++) {
 		irq_domain_set_info(domain, virq + i, hwirq + i,
@@ -250,7 +246,7 @@
 				    NULL, NULL);
 	}
 
-	return hwirq;
+	return 0;
 }
 
 static void armada_370_xp_msi_free(struct irq_domain *domain,
@@ -259,7 +255,7 @@
 	struct irq_data *d = irq_domain_get_irq_data(domain, virq);
 
 	mutex_lock(&msi_used_lock);
-	bitmap_clear(msi_used, d->hwirq, nr_irqs);
+	bitmap_release_region(msi_used, d->hwirq, order_base_2(nr_irqs));
 	mutex_unlock(&msi_used_lock);
 }
 
@@ -312,7 +308,16 @@
 
 static void armada_xp_mpic_perf_init(void)
 {
-	unsigned long cpuid = cpu_logical_map(smp_processor_id());
+	unsigned long cpuid;
+
+	/*
+	 * This Performance Counter Overflow interrupt is specific for
+	 * Armada 370 and XP. It is not available on Armada 375, 38x and 39x.
+	 */
+	if (!of_machine_is_compatible("marvell,armada-370-xp"))
+		return;
+
+	cpuid = cpu_logical_map(smp_processor_id());
 
 	/* Enable Performance Counter Overflow interrupts */
 	writel(ARMADA_370_XP_INT_CAUSE_PERF(cpuid),
@@ -541,6 +546,10 @@
 static int armada_370_xp_mpic_irq_map(struct irq_domain *h,
 				      unsigned int virq, irq_hw_number_t hw)
 {
+	/* IRQs 0 and 1 cannot be mapped, they are handled internally */
+	if (hw <= 1)
+		return -EINVAL;
+
 	armada_370_xp_irq_mask(irq_get_irq_data(virq));
 	if (!is_percpu_irq(hw))
 		writel(hw, per_cpu_int_base +
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-aspeed-i2c-ic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-aspeed-i2c-ic.c
@@ -77,8 +77,8 @@
 	}
 
 	i2c_ic->parent_irq = irq_of_parse_and_map(node, 0);
-	if (i2c_ic->parent_irq < 0) {
-		ret = i2c_ic->parent_irq;
+	if (!i2c_ic->parent_irq) {
+		ret = -EINVAL;
 		goto err_iounmap;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-aspeed-scu-ic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-aspeed-scu-ic.c
@@ -76,8 +76,8 @@
 		generic_handle_domain_irq(scu_ic->irq_domain,
 					  bit - scu_ic->irq_shift);
 
-		regmap_update_bits(scu_ic->scu, scu_ic->reg, mask,
-				   BIT(bit + ASPEED_SCU_IC_STATUS_SHIFT));
+		regmap_write_bits(scu_ic->scu, scu_ic->reg, mask,
+				  BIT(bit + ASPEED_SCU_IC_STATUS_SHIFT));
 	}
 
 	chained_irq_exit(chip, desc);
@@ -157,8 +157,8 @@
 	}
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq < 0) {
-		rc = irq;
+	if (!irq) {
+		rc = -EINVAL;
 		goto err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-bcm6345-l1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-bcm6345-l1.c
@@ -82,6 +82,7 @@
 };
 
 struct bcm6345_l1_cpu {
+	struct bcm6345_l1_chip	*intc;
 	void __iomem		*map_base;
 	unsigned int		parent_irq;
 	u32			enable_cache[];
@@ -115,17 +116,11 @@
 
 static void bcm6345_l1_irq_handle(struct irq_desc *desc)
 {
-	struct bcm6345_l1_chip *intc = irq_desc_get_handler_data(desc);
-	struct bcm6345_l1_cpu *cpu;
+	struct bcm6345_l1_cpu *cpu = irq_desc_get_handler_data(desc);
+	struct bcm6345_l1_chip *intc = cpu->intc;
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	unsigned int idx;
 
-#ifdef CONFIG_SMP
-	cpu = intc->cpus[cpu_logical_map(smp_processor_id())];
-#else
-	cpu = intc->cpus[0];
-#endif
-
 	chained_irq_enter(chip, desc);
 
 	for (idx = 0; idx < intc->n_words; idx++) {
@@ -140,7 +135,7 @@
 		for_each_set_bit(hwirq, &pending, IRQS_PER_WORD) {
 			irq = irq_linear_revmap(intc->domain, base + hwirq);
 			if (irq)
-				do_IRQ(irq);
+				generic_handle_irq(irq);
 			else
 				spurious_interrupt();
 		}
@@ -220,11 +215,11 @@
 		enabled = intc->cpus[old_cpu]->enable_cache[word] & mask;
 		if (enabled)
 			__bcm6345_l1_mask(d);
-		cpumask_copy(irq_data_get_affinity_mask(d), dest);
+		irq_data_update_affinity(d, dest);
 		if (enabled)
 			__bcm6345_l1_unmask(d);
 	} else {
-		cpumask_copy(irq_data_get_affinity_mask(d), dest);
+		irq_data_update_affinity(d, dest);
 	}
 	raw_spin_unlock_irqrestore(&intc->lock, flags);
 
@@ -257,6 +252,7 @@
 	if (!cpu)
 		return -ENOMEM;
 
+	cpu->intc = intc;
 	cpu->map_base = ioremap(res.start, sz);
 	if (!cpu->map_base)
 		return -ENOMEM;
@@ -272,7 +268,7 @@
 		return -EINVAL;
 	}
 	irq_set_chained_handler_and_data(cpu->parent_irq,
-						bcm6345_l1_irq_handle, intc);
+						bcm6345_l1_irq_handle, cpu);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-bcm7120-l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-bcm7120-l2.c
@@ -271,7 +271,8 @@
 		flags |= IRQ_GC_BE_IO;
 
 	ret = irq_alloc_domain_generic_chips(data->domain, IRQS_PER_WORD, 1,
-				dn->full_name, handle_level_irq, clr, 0, flags);
+				dn->full_name, handle_level_irq, clr,
+				IRQ_LEVEL, flags);
 	if (ret) {
 		pr_err("failed to allocate generic irq chip\n");
 		goto out_free_domain;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-brcmstb-l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-brcmstb-l2.c
@@ -2,7 +2,7 @@
 /*
  * Generic Broadcom Set Top Box Level 2 Interrupt controller driver
  *
- * Copyright (C) 2014-2017 Broadcom
+ * Copyright (C) 2014-2024 Broadcom
  */
 
 #define pr_fmt(fmt)	KBUILD_MODNAME	": " fmt
@@ -113,6 +113,9 @@
 		generic_handle_domain_irq(b->domain, irq);
 	} while (status);
 out:
+	/* Don't ack parent before all device writes are done */
+	wmb();
+
 	chained_irq_exit(chip, desc);
 }
 
@@ -161,6 +164,7 @@
 					  *init_params)
 {
 	unsigned int clr = IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN;
+	unsigned int set = 0;
 	struct brcmstb_l2_intc_data *data;
 	struct irq_chip_type *ct;
 	int ret;
@@ -208,9 +212,12 @@
 	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
 		flags |= IRQ_GC_BE_IO;
 
+	if (init_params->handler == handle_level_irq)
+		set |= IRQ_LEVEL;
+
 	/* Allocate a single Generic IRQ chip for this node */
 	ret = irq_alloc_domain_generic_chips(data->domain, 32, 1,
-			np->full_name, init_params->handler, clr, 0, flags);
+			np->full_name, init_params->handler, clr, set, flags);
 	if (ret) {
 		pr_err("failed to allocate generic irq chip\n");
 		goto out_free_domain;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-common.c
@@ -16,7 +16,13 @@
 			  const struct gic_quirk *quirks, void *data)
 {
 	for (; quirks->desc; quirks++) {
-		if (!of_device_is_compatible(np, quirks->compatible))
+		if (!quirks->compatible && !quirks->property)
+			continue;
+		if (quirks->compatible &&
+		    !of_device_is_compatible(np, quirks->compatible))
+			continue;
+		if (quirks->property &&
+		    !of_property_read_bool(np, quirks->property))
 			continue;
 		if (quirks->init(data))
 			pr_info("GIC: enabling workaround for %s\n",
@@ -28,7 +34,7 @@
 		void *data)
 {
 	for (; quirks->desc; quirks++) {
-		if (quirks->compatible)
+		if (quirks->compatible || quirks->property)
 			continue;
 		if (quirks->iidr != (quirks->mask & iidr))
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-common.h
@@ -13,6 +13,7 @@
 struct gic_quirk {
 	const char *desc;
 	const char *compatible;
+	const char *property;
 	bool (*init)(void *data);
 	u32 iidr;
 	u32 mask;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-pm.c
@@ -102,7 +102,7 @@
 
 	pm_runtime_enable(dev);
 
-	ret = pm_runtime_get_sync(dev);
+	ret = pm_runtime_resume_and_get(dev);
 	if (ret < 0)
 		goto rpm_disable;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-realview.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-realview.c
@@ -57,6 +57,7 @@
 
 	/* The PB11MPCore GIC needs to be configured in the syscon */
 	map = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (!IS_ERR(map)) {
 		/* new irq mode with no DCC */
 		regmap_write(map, REALVIEW_SYS_LOCK_OFFSET,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-v2m.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-v2m.c
@@ -439,12 +439,12 @@
 
 		ret = gicv2m_init_one(&child->fwnode, spi_start, nr_spis,
 				      &res, 0);
-		if (ret) {
-			of_node_put(child);
+		if (ret)
 			break;
-		}
 	}
 
+	if (ret && child)
+		of_node_put(child);
 	if (!ret)
 		ret = gicv2m_allocate_domains(parent);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-v3-its.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-v3-its.c
@@ -267,13 +267,23 @@
 	raw_spin_unlock_irqrestore(&vpe->vpe_lock, flags);
 }
 
+static struct irq_chip its_vpe_irq_chip;
+
 static int irq_to_cpuid_lock(struct irq_data *d, unsigned long *flags)
 {
-	struct its_vlpi_map *map = get_vlpi_map(d);
+	struct its_vpe *vpe = NULL;
 	int cpu;
 
-	if (map) {
-		cpu = vpe_to_cpuid_lock(map->vpe, flags);
+	if (d->chip == &its_vpe_irq_chip) {
+		vpe = irq_data_get_irq_chip_data(d);
+	} else {
+		struct its_vlpi_map *map = get_vlpi_map(d);
+		if (map)
+			vpe = map->vpe;
+	}
+
+	if (vpe) {
+		cpu = vpe_to_cpuid_lock(vpe, flags);
 	} else {
 		/* Physical LPIs are already locked via the irq_desc lock */
 		struct its_device *its_dev = irq_data_get_irq_chip_data(d);
@@ -287,10 +297,18 @@
 
 static void irq_to_cpuid_unlock(struct irq_data *d, unsigned long flags)
 {
-	struct its_vlpi_map *map = get_vlpi_map(d);
+	struct its_vpe *vpe = NULL;
+
+	if (d->chip == &its_vpe_irq_chip) {
+		vpe = irq_data_get_irq_chip_data(d);
+	} else {
+		struct its_vlpi_map *map = get_vlpi_map(d);
+		if (map)
+			vpe = map->vpe;
+	}
 
-	if (map)
-		vpe_to_cpuid_unlock(map->vpe, flags);
+	if (vpe)
+		vpe_to_cpuid_unlock(vpe, flags);
 }
 
 static struct its_collection *valid_col(struct its_collection *col)
@@ -742,7 +760,7 @@
 
 	its_fixup_cmd(cmd);
 
-	return NULL;
+	return desc->its_invall_cmd.col;
 }
 
 static struct its_vpe *its_build_vinvall_cmd(struct its_node *its,
@@ -761,6 +779,7 @@
 					   struct its_cmd_block *cmd,
 					   struct its_cmd_desc *desc)
 {
+	struct its_vpe *vpe = valid_vpe(its, desc->its_vmapp_cmd.vpe);
 	unsigned long vpt_addr, vconf_addr;
 	u64 target;
 	bool alloc;
@@ -770,9 +789,14 @@
 	its_encode_valid(cmd, desc->its_vmapp_cmd.valid);
 
 	if (!desc->its_vmapp_cmd.valid) {
+		alloc = !atomic_dec_return(&desc->its_vmapp_cmd.vpe->vmapp_count);
 		if (is_v4_1(its)) {
-			alloc = !atomic_dec_return(&desc->its_vmapp_cmd.vpe->vmapp_count);
 			its_encode_alloc(cmd, alloc);
+			/*
+			 * Unmapping a VPE is self-synchronizing on GICv4.1,
+			 * no need to issue a VSYNC.
+			 */
+			vpe = NULL;
 		}
 
 		goto out;
@@ -785,13 +809,13 @@
 	its_encode_vpt_addr(cmd, vpt_addr);
 	its_encode_vpt_size(cmd, LPI_NRBITS - 1);
 
+	alloc = !atomic_fetch_inc(&desc->its_vmapp_cmd.vpe->vmapp_count);
+
 	if (!is_v4_1(its))
 		goto out;
 
 	vconf_addr = virt_to_phys(page_address(desc->its_vmapp_cmd.vpe->its_vm->vprop_page));
 
-	alloc = !atomic_fetch_inc(&desc->its_vmapp_cmd.vpe->vmapp_count);
-
 	its_encode_alloc(cmd, alloc);
 
 	/*
@@ -807,7 +831,7 @@
 out:
 	its_fixup_cmd(cmd);
 
-	return valid_vpe(its, desc->its_vmapp_cmd.vpe);
+	return vpe;
 }
 
 static struct its_vpe *its_build_vmapti_cmd(struct its_node *its,
@@ -1427,14 +1451,29 @@
 		cpu_relax();
 }
 
-static void direct_lpi_inv(struct irq_data *d)
+static void __direct_lpi_inv(struct irq_data *d, u64 val)
 {
-	struct its_vlpi_map *map = get_vlpi_map(d);
 	void __iomem *rdbase;
 	unsigned long flags;
-	u64 val;
 	int cpu;
 
+	/* Target the redistributor this LPI is currently routed to */
+	cpu = irq_to_cpuid_lock(d, &flags);
+	raw_spin_lock(&gic_data_rdist_cpu(cpu)->rd_lock);
+
+	rdbase = per_cpu_ptr(gic_rdists->rdist, cpu)->rd_base;
+	gic_write_lpir(val, rdbase + GICR_INVLPIR);
+	wait_for_syncr(rdbase);
+
+	raw_spin_unlock(&gic_data_rdist_cpu(cpu)->rd_lock);
+	irq_to_cpuid_unlock(d, flags);
+}
+
+static void direct_lpi_inv(struct irq_data *d)
+{
+	struct its_vlpi_map *map = get_vlpi_map(d);
+	u64 val;
+
 	if (map) {
 		struct its_device *its_dev = irq_data_get_irq_chip_data(d);
 
@@ -1447,15 +1486,7 @@
 		val = d->hwirq;
 	}
 
-	/* Target the redistributor this LPI is currently routed to */
-	cpu = irq_to_cpuid_lock(d, &flags);
-	raw_spin_lock(&gic_data_rdist_cpu(cpu)->rd_lock);
-	rdbase = per_cpu_ptr(gic_rdists->rdist, cpu)->rd_base;
-	gic_write_lpir(val, rdbase + GICR_INVLPIR);
-
-	wait_for_syncr(rdbase);
-	raw_spin_unlock(&gic_data_rdist_cpu(cpu)->rd_lock);
-	irq_to_cpuid_unlock(d, flags);
+	__direct_lpi_inv(d, val);
 }
 
 static void lpi_update_config(struct irq_data *d, u8 clr, u8 set)
@@ -1620,7 +1651,7 @@
 
 		cpu = cpumask_pick_least_loaded(d, tmpmask);
 	} else {
-		cpumask_and(tmpmask, irq_data_get_affinity_mask(d), cpu_online_mask);
+		cpumask_copy(tmpmask, aff_mask);
 
 		/* If we cannot cross sockets, limit the search to that node */
 		if ((its_dev->its->flags & ITS_FLAGS_WORKAROUND_CAVIUM_23144) &&
@@ -3007,18 +3038,12 @@
 	return 0;
 }
 
-static u64 its_clear_vpend_valid(void __iomem *vlpi_base, u64 clr, u64 set)
+static u64 read_vpend_dirty_clear(void __iomem *vlpi_base)
 {
 	u32 count = 1000000;	/* 1s! */
 	bool clean;
 	u64 val;
 
-	val = gicr_read_vpendbaser(vlpi_base + GICR_VPENDBASER);
-	val &= ~GICR_VPENDBASER_Valid;
-	val &= ~clr;
-	val |= set;
-	gicr_write_vpendbaser(val, vlpi_base + GICR_VPENDBASER);
-
 	do {
 		val = gicr_read_vpendbaser(vlpi_base + GICR_VPENDBASER);
 		clean = !(val & GICR_VPENDBASER_Dirty);
@@ -3029,10 +3054,26 @@
 		}
 	} while (!clean && count);
 
-	if (unlikely(val & GICR_VPENDBASER_Dirty)) {
+	if (unlikely(!clean))
 		pr_err_ratelimited("ITS virtual pending table not cleaning\n");
+
+	return val;
+}
+
+static u64 its_clear_vpend_valid(void __iomem *vlpi_base, u64 clr, u64 set)
+{
+	u64 val;
+
+	/* Make sure we wait until the RD is done with the initial scan */
+	val = read_vpend_dirty_clear(vlpi_base);
+	val &= ~GICR_VPENDBASER_Valid;
+	val &= ~clr;
+	val |= set;
+	gicr_write_vpendbaser(val, vlpi_base + GICR_VPENDBASER);
+
+	val = read_vpend_dirty_clear(vlpi_base);
+	if (unlikely(val & GICR_VPENDBASER_Dirty))
 		val |= GICR_VPENDBASER_PendingLast;
-	}
 
 	return val;
 }
@@ -3765,8 +3806,16 @@
 				bool force)
 {
 	struct its_vpe *vpe = irq_data_get_irq_chip_data(d);
-	int from, cpu = cpumask_first(mask_val);
+	struct cpumask common, *table_mask;
 	unsigned long flags;
+	int from, cpu;
+
+	/*
+	 * Check if we're racing against a VPE being destroyed, for
+	 * which we don't want to allow a VMOVP.
+	 */
+	if (!atomic_read(&vpe->vmapp_count))
+		return -EINVAL;
 
 	/*
 	 * Changing affinity is mega expensive, so let's be as lazy as
@@ -3782,19 +3831,22 @@
 	 * taken on any vLPI handling path that evaluates vpe->col_idx.
 	 */
 	from = vpe_to_cpuid_lock(vpe, &flags);
-	if (from == cpu)
-		goto out;
-
-	vpe->col_idx = cpu;
+	table_mask = gic_data_rdist_cpu(from)->vpe_table_mask;
 
 	/*
-	 * GICv4.1 allows us to skip VMOVP if moving to a cpu whose RD
-	 * is sharing its VPE table with the current one.
+	 * If we are offered another CPU in the same GICv4.1 ITS
+	 * affinity, pick this one. Otherwise, any CPU will do.
 	 */
-	if (gic_data_rdist_cpu(cpu)->vpe_table_mask &&
-	    cpumask_test_cpu(from, gic_data_rdist_cpu(cpu)->vpe_table_mask))
+	if (table_mask && cpumask_and(&common, mask_val, table_mask))
+		cpu = cpumask_test_cpu(from, &common) ? from : cpumask_first(&common);
+	else
+		cpu = cpumask_first(mask_val);
+
+	if (from == cpu)
 		goto out;
 
+	vpe->col_idx = cpu;
+
 	its_send_vmovp(vpe);
 	its_vpe_db_proxy_move(vpe, from, cpu);
 
@@ -3926,18 +3978,10 @@
 {
 	struct its_vpe *vpe = irq_data_get_irq_chip_data(d);
 
-	if (gic_rdists->has_direct_lpi) {
-		void __iomem *rdbase;
-
-		/* Target the redistributor this VPE is currently known on */
-		raw_spin_lock(&gic_data_rdist_cpu(vpe->col_idx)->rd_lock);
-		rdbase = per_cpu_ptr(gic_rdists->rdist, vpe->col_idx)->rd_base;
-		gic_write_lpir(d->parent_data->hwirq, rdbase + GICR_INVLPIR);
-		wait_for_syncr(rdbase);
-		raw_spin_unlock(&gic_data_rdist_cpu(vpe->col_idx)->rd_lock);
-	} else {
+	if (gic_rdists->has_direct_lpi)
+		__direct_lpi_inv(d, d->parent_data->hwirq);
+	else
 		its_vpe_send_cmd(vpe, its_send_inv);
-	}
 }
 
 static void its_vpe_mask_irq(struct irq_data *d)
@@ -4409,9 +4453,8 @@
 	raw_spin_lock_init(&vpe->vpe_lock);
 	vpe->vpe_id = vpe_id;
 	vpe->vpt_page = vpt_page;
-	if (gic_rdists->has_rvpeid)
-		atomic_set(&vpe->vmapp_count, 0);
-	else
+	atomic_set(&vpe->vmapp_count, 0);
+	if (!gic_rdists->has_rvpeid)
 		vpe->vpe_proxy_event = -1;
 
 	return 0;
@@ -4460,8 +4503,6 @@
 	struct page *vprop_page;
 	int base, nr_ids, i, err = 0;
 
-	BUG_ON(!vm);
-
 	bitmap = its_lpi_alloc(roundup_pow_of_two(nr_irqs), &base, &nr_ids);
 	if (!bitmap)
 		return -ENOMEM;
@@ -4499,13 +4540,8 @@
 		set_bit(i, bitmap);
 	}
 
-	if (err) {
-		if (i > 0)
-			its_vpe_irq_domain_free(domain, virq, i);
-
-		its_lpi_free(bitmap, base, nr_ids);
-		its_free_prop_table(vprop_page);
-	}
+	if (err)
+		its_vpe_irq_domain_free(domain, virq, i);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic-v3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic-v3.c
@@ -35,6 +35,7 @@
 
 #define FLAGS_WORKAROUND_GICR_WAKER_MSM8996	(1ULL << 0)
 #define FLAGS_WORKAROUND_CAVIUM_ERRATUM_38539	(1ULL << 1)
+#define FLAGS_WORKAROUND_MTK_GICR_SAVE		(1ULL << 2)
 
 #define GIC_IRQ_TYPE_PARTITION	(GIC_IRQ_TYPE_LPI + 1)
 
@@ -206,11 +207,11 @@
 	}
 }
 
-static void gic_do_wait_for_rwp(void __iomem *base)
+static void gic_do_wait_for_rwp(void __iomem *base, u32 bit)
 {
 	u32 count = 1000000;	/* 1s! */
 
-	while (readl_relaxed(base + GICD_CTLR) & GICD_CTLR_RWP) {
+	while (readl_relaxed(base + GICD_CTLR) & bit) {
 		count--;
 		if (!count) {
 			pr_err_ratelimited("RWP timeout, gone fishing\n");
@@ -224,13 +225,13 @@
 /* Wait for completion of a distributor change */
 static void gic_dist_wait_for_rwp(void)
 {
-	gic_do_wait_for_rwp(gic_data.dist_base);
+	gic_do_wait_for_rwp(gic_data.dist_base, GICD_CTLR_RWP);
 }
 
 /* Wait for completion of a redistributor change */
 static void gic_redist_wait_for_rwp(void)
 {
-	gic_do_wait_for_rwp(gic_data_rdist_rd_base());
+	gic_do_wait_for_rwp(gic_data_rdist_rd_base(), GICR_CTLR_RWP);
 }
 
 #ifdef CONFIG_ARM64
@@ -428,6 +429,13 @@
 	}
 
 	gic_poke_irq(d, reg);
+
+	/*
+	 * Force read-back to guarantee that the active state has taken
+	 * effect, and won't race with a guest-driven deactivation.
+	 */
+	if (reg == GICD_ISACTIVER)
+		gic_peek_irq(d, reg);
 	return 0;
 }
 
@@ -556,7 +564,8 @@
 
 static void gic_eoi_irq(struct irq_data *d)
 {
-	gic_write_eoir(gic_irq(d));
+	write_gicreg(gic_irq(d), ICC_EOIR1_EL1);
+	isb();
 }
 
 static void gic_eoimode1_eoi_irq(struct irq_data *d)
@@ -640,10 +649,38 @@
 		if (irqnr < 8192)
 			gic_write_dir(irqnr);
 	} else {
-		gic_write_eoir(irqnr);
+		write_gicreg(irqnr, ICC_EOIR1_EL1);
+		isb();
 	}
 }
 
+/*
+ * Follow a read of the IAR with any HW maintenance that needs to happen prior
+ * to invoking the relevant IRQ handler. We must do two things:
+ *
+ * (1) Ensure instruction ordering between a read of IAR and subsequent
+ *     instructions in the IRQ handler using an ISB.
+ *
+ *     It is possible for the IAR to report an IRQ which was signalled *after*
+ *     the CPU took an IRQ exception as multiple interrupts can race to be
+ *     recognized by the GIC, earlier interrupts could be withdrawn, and/or
+ *     later interrupts could be prioritized by the GIC.
+ *
+ *     For devices which are tightly coupled to the CPU, such as PMUs, a
+ *     context synchronization event is necessary to ensure that system
+ *     register state is not stale, as these may have been indirectly written
+ *     *after* exception entry.
+ *
+ * (2) Deactivate the interrupt when EOI mode 1 is in use.
+ */
+static inline void gic_complete_ack(u32 irqnr)
+{
+	if (static_branch_likely(&supports_deactivate_key))
+		write_gicreg(irqnr, ICC_EOIR1_EL1);
+
+	isb();
+}
+
 static inline void gic_handle_nmi(u32 irqnr, struct pt_regs *regs)
 {
 	bool irqs_enabled = interrupts_enabled(regs);
@@ -652,8 +689,8 @@
 	if (irqs_enabled)
 		nmi_enter();
 
-	if (static_branch_likely(&supports_deactivate_key))
-		gic_write_eoir(irqnr);
+	gic_complete_ack(irqnr);
+
 	/*
 	 * Leave the PSR.I bit set to prevent other NMIs to be
 	 * received while handling this one.
@@ -723,10 +760,7 @@
 		gic_arch_enable_irqs();
 	}
 
-	if (static_branch_likely(&supports_deactivate_key))
-		gic_write_eoir(irqnr);
-	else
-		isb();
+	gic_complete_ack(irqnr);
 
 	if (handle_domain_irq(gic_data.domain, irqnr, regs)) {
 		WARN_ONCE(true, "Unexpected interrupt received!\n");
@@ -920,6 +954,22 @@
 {
 	u64 typer = gic_read_typer(ptr + GICR_TYPER);
 
+	/* Boot-time cleanip */
+	if ((typer & GICR_TYPER_VLPIS) && (typer & GICR_TYPER_RVPEID)) {
+		u64 val;
+
+		/* Deactivate any present vPE */
+		val = gicr_read_vpendbaser(ptr + SZ_128K + GICR_VPENDBASER);
+		if (val & GICR_VPENDBASER_Valid)
+			gicr_write_vpendbaser(GICR_VPENDBASER_PendingLast,
+					      ptr + SZ_128K + GICR_VPENDBASER);
+
+		/* Mark the VPE table as invalid */
+		val = gicr_read_vpropbaser(ptr + SZ_128K + GICR_VPROPBASER);
+		val &= ~GICR_VPROPBASER_4_1_VALID;
+		gicr_write_vpropbaser(val, ptr + SZ_128K + GICR_VPROPBASER);
+	}
+
 	gic_data.rdists.has_vlpis &= !!(typer & GICR_TYPER_VLPIS);
 
 	/* RVPEID implies some form of DirectLPI, no matter what the doc says... :-/ */
@@ -1290,7 +1340,7 @@
 static int gic_cpu_pm_notifier(struct notifier_block *self,
 			       unsigned long cmd, void *v)
 {
-	if (cmd == CPU_PM_EXIT) {
+	if (cmd == CPU_PM_EXIT || cmd == CPU_PM_ENTER_FAILED) {
 		if (gic_dist_security_disabled())
 			gic_enable_redist(true);
 		gic_cpu_sys_reg_init();
@@ -1450,6 +1500,12 @@
 		if(fwspec->param_count != 2)
 			return -EINVAL;
 
+		if (fwspec->param[0] < 16) {
+			pr_err(FW_BUG "Illegal GSI%d translation request\n",
+			       fwspec->param[0]);
+			return -EINVAL;
+		}
+
 		*hwirq = fwspec->param[0];
 		*type = fwspec->param[1];
 
@@ -1598,6 +1654,15 @@
 	return true;
 }
 
+static bool gic_enable_quirk_mtk_gicr(void *data)
+{
+	struct gic_chip_data *d = data;
+
+	d->flags |= FLAGS_WORKAROUND_MTK_GICR_SAVE;
+
+	return true;
+}
+
 static bool gic_enable_quirk_cavium_38539(void *data)
 {
 	struct gic_chip_data *d = data;
@@ -1634,6 +1699,11 @@
 		.init	= gic_enable_quirk_msm8996,
 	},
 	{
+		.desc	= "GICv3: Mediatek Chromebook GICR save problem",
+		.property = "mediatek,broken-save-restore-fw",
+		.init	= gic_enable_quirk_mtk_gicr,
+	},
+	{
 		.desc	= "GICv3: HIP06 erratum 161010803",
 		.iidr	= 0x0204043b,
 		.mask	= 0xffffffff,
@@ -1669,6 +1739,11 @@
 	if (!gic_prio_masking_enabled())
 		return;
 
+	if (gic_data.flags & FLAGS_WORKAROUND_MTK_GICR_SAVE) {
+		pr_warn("Skipping NMI enable due to firmware issues\n");
+		return;
+	}
+
 	ppi_nmi_refs = kcalloc(gic_data.ppi_nr, sizeof(*ppi_nmi_refs), GFP_KERNEL);
 	if (!ppi_nmi_refs)
 		return;
@@ -1842,7 +1917,7 @@
 
 	gic_data.ppi_descs = kcalloc(gic_data.ppi_nr, sizeof(*gic_data.ppi_descs), GFP_KERNEL);
 	if (!gic_data.ppi_descs)
-		return;
+		goto out_put_node;
 
 	nr_parts = of_get_child_count(parts_node);
 
@@ -1883,12 +1958,15 @@
 				continue;
 
 			cpu = of_cpu_node_to_id(cpu_node);
-			if (WARN_ON(cpu < 0))
+			if (WARN_ON(cpu < 0)) {
+				of_node_put(cpu_node);
 				continue;
+			}
 
 			pr_cont("%pOF[%d] ", cpu_node, cpu);
 
 			cpumask_set_cpu(cpu, &part->mask);
+			of_node_put(cpu_node);
 		}
 
 		pr_cont("}\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-gic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-gic.c
@@ -62,7 +62,7 @@
 
 union gic_base {
 	void __iomem *common_base;
-	void __percpu * __iomem *percpu_base;
+	void __iomem * __percpu *percpu_base;
 };
 
 struct gic_chip_data {
@@ -818,18 +818,30 @@
 	return IRQ_SET_MASK_OK_DONE;
 }
 
-static void gic_ipi_send_mask(struct irq_data *d, const struct cpumask *mask)
+void gic_set_cpu(unsigned int cpu, unsigned int irq)
+{
+	struct irq_data *d = irq_get_irq_data(irq);
+	struct cpumask mask;
+
+	cpumask_clear(&mask);
+	cpumask_set_cpu(cpu, &mask);
+	gic_set_affinity(d, &mask, true);
+}
+EXPORT_SYMBOL(gic_set_cpu);
+
+void gic_ipi_send_mask(struct irq_data *d, const struct cpumask *mask)
 {
 	int cpu;
 	unsigned long flags, map = 0;
 
+#if 0
 	if (unlikely(nr_cpu_ids == 1)) {
 		/* Only one CPU? let's do a self-IPI... */
 		writel_relaxed(2 << 24 | d->hwirq,
 			       gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
 		return;
 	}
-
+#endif
 	gic_lock_irqsave(flags);
 
 	/* Convert our logical CPU mask into a physical one. */
@@ -847,6 +859,7 @@
 
 	gic_unlock_irqrestore(flags);
 }
+EXPORT_SYMBOL(gic_ipi_send_mask);
 
 static int gic_starting_cpu(unsigned int cpu)
 {
@@ -894,6 +907,7 @@
 	/* this always happens on GIC0 */
 	writel_relaxed((cpu_id << 16) | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT);
 }
+EXPORT_SYMBOL(gic_send_sgi);
 
 /*
  * gic_get_cpu_id - get the CPU interface ID for the specified CPU
@@ -1085,6 +1099,12 @@
 		if(fwspec->param_count != 2)
 			return -EINVAL;
 
+		if (fwspec->param[0] < 16) {
+			pr_err(FW_BUG "Illegal GSI%d translation request\n",
+			       fwspec->param[0]);
+			return -EINVAL;
+		}
+
 		*hwirq = fwspec->param[0];
 		*type = fwspec->param[1];
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-imx-irqsteer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-imx-irqsteer.c
@@ -12,6 +12,7 @@
 #include <linux/kernel.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
 #include <linux/spinlock.h>
 
 #define CTRL_STRIDE_OFF(_t, _r)	(_t * 4 * _r)
@@ -34,6 +35,7 @@
 	int			channel;
 	struct irq_domain	*domain;
 	u32			*saved_reg;
+	struct device		*dev;
 };
 
 static int imx_irqsteer_get_reg_index(struct irqsteer_data *data,
@@ -70,10 +72,26 @@
 	raw_spin_unlock_irqrestore(&data->lock, flags);
 }
 
-static struct irq_chip imx_irqsteer_irq_chip = {
-	.name		= "irqsteer",
-	.irq_mask	= imx_irqsteer_irq_mask,
-	.irq_unmask	= imx_irqsteer_irq_unmask,
+static void imx_irqsteer_irq_bus_lock(struct irq_data *d)
+{
+	struct irqsteer_data *data = d->chip_data;
+
+	pm_runtime_get_sync(data->dev);
+}
+
+static void imx_irqsteer_irq_bus_sync_unlock(struct irq_data *d)
+{
+	struct irqsteer_data *data = d->chip_data;
+
+	pm_runtime_put_autosuspend(data->dev);
+}
+
+static const struct irq_chip imx_irqsteer_irq_chip = {
+	.name			= "irqsteer",
+	.irq_mask		= imx_irqsteer_irq_mask,
+	.irq_unmask		= imx_irqsteer_irq_unmask,
+	.irq_bus_lock		= imx_irqsteer_irq_bus_lock,
+	.irq_bus_sync_unlock	= imx_irqsteer_irq_bus_sync_unlock,
 };
 
 static int imx_irqsteer_irq_map(struct irq_domain *h, unsigned int irq,
@@ -148,6 +166,7 @@
 	if (!data)
 		return -ENOMEM;
 
+	data->dev = &pdev->dev;
 	data->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(data->regs)) {
 		dev_err(&pdev->dev, "failed to initialize reg\n");
@@ -175,7 +194,7 @@
 	data->irq_count = DIV_ROUND_UP(irqs_num, 64);
 	data->reg_num = irqs_num / 32;
 
-	if (IS_ENABLED(CONFIG_PM_SLEEP)) {
+	if (IS_ENABLED(CONFIG_PM)) {
 		data->saved_reg = devm_kzalloc(&pdev->dev,
 					sizeof(u32) * data->reg_num,
 					GFP_KERNEL);
@@ -199,6 +218,7 @@
 		ret = -ENOMEM;
 		goto out;
 	}
+	irq_domain_set_pm_device(data->domain, &pdev->dev);
 
 	if (!data->irq_count || data->irq_count > CHAN_MAX_OUTPUT_INT) {
 		ret = -EINVAL;
@@ -219,6 +239,9 @@
 
 	platform_set_drvdata(pdev, data);
 
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
 	return 0;
 out:
 	clk_disable_unprepare(data->ipg_clk);
@@ -241,7 +264,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
 static void imx_irqsteer_save_regs(struct irqsteer_data *data)
 {
 	int i;
@@ -288,7 +311,10 @@
 #endif
 
 static const struct dev_pm_ops imx_irqsteer_pm_ops = {
-	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(imx_irqsteer_suspend, imx_irqsteer_resume)
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				      pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(imx_irqsteer_suspend,
+			   imx_irqsteer_resume, NULL)
 };
 
 static const struct of_device_id imx_irqsteer_dt_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-jcore-aic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-jcore-aic.c
@@ -68,6 +68,7 @@
 	unsigned min_irq = JCORE_AIC2_MIN_HWIRQ;
 	unsigned dom_sz = JCORE_AIC_MAX_HWIRQ+1;
 	struct irq_domain *domain;
+	int ret;
 
 	pr_info("Initializing J-Core AIC\n");
 
@@ -100,6 +101,12 @@
 	jcore_aic.irq_unmask = noop;
 	jcore_aic.name = "AIC";
 
+	ret = irq_alloc_descs(-1, min_irq, dom_sz - min_irq,
+			      of_node_to_nid(node));
+
+	if (ret < 0)
+		return ret;
+
 	domain = irq_domain_add_legacy(node, dom_sz - min_irq, min_irq, min_irq,
 				       &jcore_aic_irqdomain_ops,
 				       &jcore_aic);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-loongson-pch-msi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-loongson-pch-msi.c
@@ -132,7 +132,7 @@
 
 err_hwirq:
 	pch_msi_free_hwirq(priv, hwirq, nr_irqs);
-	irq_domain_free_irqs_parent(domain, virq, i - 1);
+	irq_domain_free_irqs_parent(domain, virq, i);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-mbigen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-mbigen.c
@@ -64,6 +64,20 @@
 	void __iomem		*base;
 };
 
+static inline unsigned int get_mbigen_node_offset(unsigned int nid)
+{
+	unsigned int offset = nid * MBIGEN_NODE_OFFSET;
+
+	/*
+	 * To avoid touched clear register in unexpected way, we need to directly
+	 * skip clear register when access to more than 10 mbigen nodes.
+	 */
+	if (nid >= (REG_MBIGEN_CLEAR_OFFSET / MBIGEN_NODE_OFFSET))
+		offset += MBIGEN_NODE_OFFSET;
+
+	return offset;
+}
+
 static inline unsigned int get_mbigen_vec_reg(irq_hw_number_t hwirq)
 {
 	unsigned int nid, pin;
@@ -72,8 +86,7 @@
 	nid = hwirq / IRQS_PER_MBIGEN_NODE + 1;
 	pin = hwirq % IRQS_PER_MBIGEN_NODE;
 
-	return pin * 4 + nid * MBIGEN_NODE_OFFSET
-			+ REG_MBIGEN_VEC_OFFSET;
+	return pin * 4 + get_mbigen_node_offset(nid) + REG_MBIGEN_VEC_OFFSET;
 }
 
 static inline void get_mbigen_type_reg(irq_hw_number_t hwirq,
@@ -88,8 +101,7 @@
 	*mask = 1 << (irq_ofst % 32);
 	ofst = irq_ofst / 32 * 4;
 
-	*addr = ofst + nid * MBIGEN_NODE_OFFSET
-		+ REG_MBIGEN_TYPE_OFFSET;
+	*addr = ofst + get_mbigen_node_offset(nid) + REG_MBIGEN_TYPE_OFFSET;
 }
 
 static inline void get_mbigen_clear_reg(irq_hw_number_t hwirq,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-meson-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-meson-gpio.c
@@ -16,7 +16,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 
-#define NUM_CHANNEL 8
+#define MAX_NUM_CHANNEL 64
 #define MAX_INPUT_MUX 256
 
 #define REG_EDGE_POL	0x00
@@ -60,6 +60,7 @@
 
 struct meson_gpio_irq_params {
 	unsigned int nr_hwirq;
+	unsigned int nr_channels;
 	bool support_edge_both;
 	unsigned int edge_both_offset;
 	unsigned int edge_single_offset;
@@ -81,6 +82,7 @@
 	.edge_single_offset = 0,				\
 	.pol_low_offset = 16,					\
 	.pin_sel_mask = 0xff,					\
+	.nr_channels = 8,					\
 
 #define INIT_MESON_A1_COMMON_DATA(irqs)				\
 	INIT_MESON_COMMON(irqs, meson_a1_gpio_irq_init,		\
@@ -90,6 +92,7 @@
 	.edge_single_offset = 8,				\
 	.pol_low_offset = 0,					\
 	.pin_sel_mask = 0x7f,					\
+	.nr_channels = 8,					\
 
 static const struct meson_gpio_irq_params meson8_params = {
 	INIT_MESON8_COMMON_DATA(134)
@@ -136,9 +139,9 @@
 struct meson_gpio_irq_controller {
 	const struct meson_gpio_irq_params *params;
 	void __iomem *base;
-	u32 channel_irqs[NUM_CHANNEL];
-	DECLARE_BITMAP(channel_map, NUM_CHANNEL);
-	spinlock_t lock;
+	u32 channel_irqs[MAX_NUM_CHANNEL];
+	DECLARE_BITMAP(channel_map, MAX_NUM_CHANNEL);
+	raw_spinlock_t lock;
 };
 
 static void meson_gpio_irq_update_bits(struct meson_gpio_irq_controller *ctl,
@@ -147,14 +150,14 @@
 	unsigned long flags;
 	u32 tmp;
 
-	spin_lock_irqsave(&ctl->lock, flags);
+	raw_spin_lock_irqsave(&ctl->lock, flags);
 
 	tmp = readl_relaxed(ctl->base + reg);
 	tmp &= ~mask;
 	tmp |= val;
 	writel_relaxed(tmp, ctl->base + reg);
 
-	spin_unlock_irqrestore(&ctl->lock, flags);
+	raw_spin_unlock_irqrestore(&ctl->lock, flags);
 }
 
 static void meson_gpio_irq_init_dummy(struct meson_gpio_irq_controller *ctl)
@@ -204,12 +207,12 @@
 	unsigned long flags;
 	unsigned int idx;
 
-	spin_lock_irqsave(&ctl->lock, flags);
+	raw_spin_lock_irqsave(&ctl->lock, flags);
 
 	/* Find a free channel */
-	idx = find_first_zero_bit(ctl->channel_map, NUM_CHANNEL);
-	if (idx >= NUM_CHANNEL) {
-		spin_unlock_irqrestore(&ctl->lock, flags);
+	idx = find_first_zero_bit(ctl->channel_map, ctl->params->nr_channels);
+	if (idx >= ctl->params->nr_channels) {
+		raw_spin_unlock_irqrestore(&ctl->lock, flags);
 		pr_err("No channel available\n");
 		return -ENOSPC;
 	}
@@ -217,7 +220,7 @@
 	/* Mark the channel as used */
 	set_bit(idx, ctl->channel_map);
 
-	spin_unlock_irqrestore(&ctl->lock, flags);
+	raw_spin_unlock_irqrestore(&ctl->lock, flags);
 
 	/*
 	 * Setup the mux of the channel to route the signal of the pad
@@ -451,10 +454,10 @@
 	ret = of_property_read_variable_u32_array(node,
 						  "amlogic,channel-interrupts",
 						  ctl->channel_irqs,
-						  NUM_CHANNEL,
-						  NUM_CHANNEL);
+						  ctl->params->nr_channels,
+						  ctl->params->nr_channels);
 	if (ret < 0) {
-		pr_err("can't get %d channel interrupts\n", NUM_CHANNEL);
+		pr_err("can't get %d channel interrupts\n", ctl->params->nr_channels);
 		return ret;
 	}
 
@@ -485,7 +488,7 @@
 	if (!ctl)
 		return -ENOMEM;
 
-	spin_lock_init(&ctl->lock);
+	raw_spin_lock_init(&ctl->lock);
 
 	ctl->base = of_iomap(node, 0);
 	if (!ctl->base) {
@@ -509,7 +512,7 @@
 	}
 
 	pr_info("%d to %d gpio interrupt mux initialized\n",
-		ctl->params->nr_hwirq, NUM_CHANNEL);
+		ctl->params->nr_hwirq, ctl->params->nr_channels);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-mips-gic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-mips-gic.c
@@ -49,15 +49,17 @@
 
 static DEFINE_PER_CPU_READ_MOSTLY(unsigned long[GIC_MAX_LONGS], pcpu_masks);
 
-static DEFINE_SPINLOCK(gic_lock);
+static DEFINE_RAW_SPINLOCK(gic_lock);
 static struct irq_domain *gic_irq_domain;
-static struct irq_domain *gic_ipi_domain;
 static int gic_shared_intrs;
 static unsigned int gic_cpu_pin;
 static unsigned int timer_cpu_pin;
 static struct irq_chip gic_level_irq_controller, gic_edge_irq_controller;
+
+#ifdef CONFIG_GENERIC_IRQ_IPI
 static DECLARE_BITMAP(ipi_resrv, GIC_MAX_INTRS);
 static DECLARE_BITMAP(ipi_available, GIC_MAX_INTRS);
+#endif /* CONFIG_GENERIC_IRQ_IPI */
 
 static struct gic_all_vpes_chip_data {
 	u32	map;
@@ -208,7 +210,7 @@
 
 	irq = GIC_HWIRQ_TO_SHARED(d->hwirq);
 
-	spin_lock_irqsave(&gic_lock, flags);
+	raw_spin_lock_irqsave(&gic_lock, flags);
 	switch (type & IRQ_TYPE_SENSE_MASK) {
 	case IRQ_TYPE_EDGE_FALLING:
 		pol = GIC_POL_FALLING_EDGE;
@@ -248,7 +250,7 @@
 	else
 		irq_set_chip_handler_name_locked(d, &gic_level_irq_controller,
 						 handle_level_irq, NULL);
-	spin_unlock_irqrestore(&gic_lock, flags);
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 
 	return 0;
 }
@@ -266,7 +268,7 @@
 		return -EINVAL;
 
 	/* Assumption : cpumask refers to a single CPU */
-	spin_lock_irqsave(&gic_lock, flags);
+	raw_spin_lock_irqsave(&gic_lock, flags);
 
 	/* Re-route this IRQ */
 	write_gic_map_vp(irq, BIT(mips_cm_vp_id(cpu)));
@@ -277,7 +279,7 @@
 		set_bit(irq, per_cpu_ptr(pcpu_masks, cpu));
 
 	irq_data_update_effective_affinity(d, cpumask_of(cpu));
-	spin_unlock_irqrestore(&gic_lock, flags);
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 
 	return IRQ_SET_MASK_OK;
 }
@@ -355,12 +357,12 @@
 	cd = irq_data_get_irq_chip_data(d);
 	cd->mask = false;
 
-	spin_lock_irqsave(&gic_lock, flags);
+	raw_spin_lock_irqsave(&gic_lock, flags);
 	for_each_online_cpu(cpu) {
 		write_gic_vl_other(mips_cm_vp_id(cpu));
 		write_gic_vo_rmask(BIT(intr));
 	}
-	spin_unlock_irqrestore(&gic_lock, flags);
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 }
 
 static void gic_unmask_local_irq_all_vpes(struct irq_data *d)
@@ -373,32 +375,45 @@
 	cd = irq_data_get_irq_chip_data(d);
 	cd->mask = true;
 
-	spin_lock_irqsave(&gic_lock, flags);
+	raw_spin_lock_irqsave(&gic_lock, flags);
 	for_each_online_cpu(cpu) {
 		write_gic_vl_other(mips_cm_vp_id(cpu));
 		write_gic_vo_smask(BIT(intr));
 	}
-	spin_unlock_irqrestore(&gic_lock, flags);
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 }
 
-static void gic_all_vpes_irq_cpu_online(struct irq_data *d)
+static void gic_all_vpes_irq_cpu_online(void)
 {
-	struct gic_all_vpes_chip_data *cd;
-	unsigned int intr;
+	static const unsigned int local_intrs[] = {
+		GIC_LOCAL_INT_TIMER,
+		GIC_LOCAL_INT_PERFCTR,
+		GIC_LOCAL_INT_FDC,
+	};
+	unsigned long flags;
+	int i;
 
-	intr = GIC_HWIRQ_TO_LOCAL(d->hwirq);
-	cd = irq_data_get_irq_chip_data(d);
+	raw_spin_lock_irqsave(&gic_lock, flags);
+
+	for (i = 0; i < ARRAY_SIZE(local_intrs); i++) {
+		unsigned int intr = local_intrs[i];
+		struct gic_all_vpes_chip_data *cd;
+
+		if (!gic_local_irq_is_routable(intr))
+			continue;
+		cd = &gic_all_vpes_chip_data[intr];
+		write_gic_vl_map(mips_gic_vx_map_reg(intr), cd->map);
+		if (cd->mask)
+			write_gic_vl_smask(BIT(intr));
+	}
 
-	write_gic_vl_map(mips_gic_vx_map_reg(intr), cd->map);
-	if (cd->mask)
-		write_gic_vl_smask(BIT(intr));
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 }
 
 static struct irq_chip gic_all_vpes_local_irq_controller = {
 	.name			= "MIPS GIC Local",
 	.irq_mask		= gic_mask_local_irq_all_vpes,
 	.irq_unmask		= gic_unmask_local_irq_all_vpes,
-	.irq_cpu_online		= gic_all_vpes_irq_cpu_online,
 };
 
 static void __gic_irq_dispatch(void)
@@ -422,11 +437,11 @@
 
 	data = irq_get_irq_data(virq);
 
-	spin_lock_irqsave(&gic_lock, flags);
+	raw_spin_lock_irqsave(&gic_lock, flags);
 	write_gic_map_pin(intr, GIC_MAP_PIN_MAP_TO_PIN | gic_cpu_pin);
 	write_gic_map_vp(intr, BIT(mips_cm_vp_id(cpu)));
 	irq_data_update_effective_affinity(data, cpumask_of(cpu));
-	spin_unlock_irqrestore(&gic_lock, flags);
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 
 	return 0;
 }
@@ -460,9 +475,11 @@
 	u32 map;
 
 	if (hwirq >= GIC_SHARED_HWIRQ_BASE) {
+#ifdef CONFIG_GENERIC_IRQ_IPI
 		/* verify that shared irqs don't conflict with an IPI irq */
 		if (test_bit(GIC_HWIRQ_TO_SHARED(hwirq), ipi_resrv))
 			return -EBUSY;
+#endif /* CONFIG_GENERIC_IRQ_IPI */
 
 		err = irq_domain_set_hwirq_and_chip(d, virq, hwirq,
 						    &gic_level_irq_controller,
@@ -477,6 +494,10 @@
 	intr = GIC_HWIRQ_TO_LOCAL(hwirq);
 	map = GIC_MAP_PIN_MAP_TO_PIN | gic_cpu_pin;
 
+	/*
+	 * If adding support for more per-cpu interrupts, keep the the
+	 * array in gic_all_vpes_irq_cpu_online() in sync.
+	 */
 	switch (intr) {
 	case GIC_LOCAL_INT_TIMER:
 		/* CONFIG_MIPS_CMP workaround (see __gic_init) */
@@ -515,12 +536,12 @@
 	if (!gic_local_irq_is_routable(intr))
 		return -EPERM;
 
-	spin_lock_irqsave(&gic_lock, flags);
+	raw_spin_lock_irqsave(&gic_lock, flags);
 	for_each_online_cpu(cpu) {
 		write_gic_vl_other(mips_cm_vp_id(cpu));
 		write_gic_vo_map(mips_gic_vx_map_reg(intr), map);
 	}
-	spin_unlock_irqrestore(&gic_lock, flags);
+	raw_spin_unlock_irqrestore(&gic_lock, flags);
 
 	return 0;
 }
@@ -551,6 +572,8 @@
 	.map = gic_irq_domain_map,
 };
 
+#ifdef CONFIG_GENERIC_IRQ_IPI
+
 static int gic_ipi_domain_xlate(struct irq_domain *d, struct device_node *ctrlr,
 				const u32 *intspec, unsigned int intsize,
 				irq_hw_number_t *out_hwirq,
@@ -654,6 +677,48 @@
 	.match = gic_ipi_domain_match,
 };
 
+static int gic_register_ipi_domain(struct device_node *node)
+{
+	struct irq_domain *gic_ipi_domain;
+	unsigned int v[2], num_ipis;
+
+	gic_ipi_domain = irq_domain_add_hierarchy(gic_irq_domain,
+						  IRQ_DOMAIN_FLAG_IPI_PER_CPU,
+						  GIC_NUM_LOCAL_INTRS + gic_shared_intrs,
+						  node, &gic_ipi_domain_ops, NULL);
+	if (!gic_ipi_domain) {
+		pr_err("Failed to add IPI domain");
+		return -ENXIO;
+	}
+
+	irq_domain_update_bus_token(gic_ipi_domain, DOMAIN_BUS_IPI);
+
+	if (node &&
+	    !of_property_read_u32_array(node, "mti,reserved-ipi-vectors", v, 2)) {
+		bitmap_set(ipi_resrv, v[0], v[1]);
+	} else {
+		/*
+		 * Reserve 2 interrupts per possible CPU/VP for use as IPIs,
+		 * meeting the requirements of arch/mips SMP.
+		 */
+		num_ipis = 2 * num_possible_cpus();
+		bitmap_set(ipi_resrv, gic_shared_intrs - num_ipis, num_ipis);
+	}
+
+	bitmap_copy(ipi_available, ipi_resrv, GIC_MAX_INTRS);
+
+	return 0;
+}
+
+#else /* !CONFIG_GENERIC_IRQ_IPI */
+
+static inline int gic_register_ipi_domain(struct device_node *node)
+{
+	return 0;
+}
+
+#endif /* !CONFIG_GENERIC_IRQ_IPI */
+
 static int gic_cpu_startup(unsigned int cpu)
 {
 	/* Enable or disable EIC */
@@ -663,8 +728,8 @@
 	/* Clear all local IRQ masks (ie. disable all local interrupts) */
 	write_gic_vl_rmask(~0);
 
-	/* Invoke irq_cpu_online callbacks to enable desired interrupts */
-	irq_cpu_online();
+	/* Enable desired interrupts */
+	gic_all_vpes_irq_cpu_online();
 
 	return 0;
 }
@@ -672,11 +737,12 @@
 static int __init gic_of_init(struct device_node *node,
 			      struct device_node *parent)
 {
-	unsigned int cpu_vec, i, gicconfig, v[2], num_ipis;
+	unsigned int cpu_vec, i, gicconfig;
 	unsigned long reserved;
 	phys_addr_t gic_base;
 	struct resource res;
 	size_t gic_len;
+	int ret;
 
 	/* Find the first available CPU vector. */
 	i = 0;
@@ -718,6 +784,10 @@
 	}
 
 	mips_gic_base = ioremap(gic_base, gic_len);
+	if (!mips_gic_base) {
+		pr_err("Failed to ioremap gic_base\n");
+		return -ENOMEM;
+	}
 
 	gicconfig = read_gic_config();
 	gic_shared_intrs = gicconfig & GIC_CONFIG_NUMINTERRUPTS;
@@ -765,30 +835,9 @@
 		return -ENXIO;
 	}
 
-	gic_ipi_domain = irq_domain_add_hierarchy(gic_irq_domain,
-						  IRQ_DOMAIN_FLAG_IPI_PER_CPU,
-						  GIC_NUM_LOCAL_INTRS + gic_shared_intrs,
-						  node, &gic_ipi_domain_ops, NULL);
-	if (!gic_ipi_domain) {
-		pr_err("Failed to add IPI domain");
-		return -ENXIO;
-	}
-
-	irq_domain_update_bus_token(gic_ipi_domain, DOMAIN_BUS_IPI);
-
-	if (node &&
-	    !of_property_read_u32_array(node, "mti,reserved-ipi-vectors", v, 2)) {
-		bitmap_set(ipi_resrv, v[0], v[1]);
-	} else {
-		/*
-		 * Reserve 2 interrupts per possible CPU/VP for use as IPIs,
-		 * meeting the requirements of arch/mips SMP.
-		 */
-		num_ipis = 2 * num_possible_cpus();
-		bitmap_set(ipi_resrv, gic_shared_intrs - num_ipis, num_ipis);
-	}
-
-	bitmap_copy(ipi_available, ipi_resrv, GIC_MAX_INTRS);
+	ret = gic_register_ipi_domain(node);
+	if (ret)
+		return ret;
 
 	board_bind_eic_interrupt = &gic_bind_eic_interrupt;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-mscc-ocelot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-mscc-ocelot.c
@@ -37,7 +37,7 @@
 	.reg_off_ena_clr	= 0x1c,
 	.reg_off_ena_set	= 0x20,
 	.reg_off_ident		= 0x38,
-	.reg_off_trigger	= 0x5c,
+	.reg_off_trigger	= 0x4,
 	.n_irq			= 24,
 };
 
@@ -70,7 +70,7 @@
 	.reg_off_ena_clr	= 0x1c,
 	.reg_off_ena_set	= 0x20,
 	.reg_off_ident		= 0x38,
-	.reg_off_trigger	= 0x5c,
+	.reg_off_trigger	= 0x4,
 	.n_irq			= 29,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-mvebu-gicp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-mvebu-gicp.c
@@ -221,6 +221,7 @@
 	}
 
 	parent_domain = irq_find_host(irq_parent_dn);
+	of_node_put(irq_parent_dn);
 	if (!parent_domain) {
 		dev_err(&pdev->dev, "failed to find parent IRQ domain\n");
 		return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-nvic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-nvic.c
@@ -26,7 +26,7 @@
 
 #define NVIC_ISER		0x000
 #define NVIC_ICER		0x080
-#define NVIC_IPR		0x300
+#define NVIC_IPR		0x400
 
 #define NVIC_MAX_BANKS		16
 /*
@@ -92,6 +92,7 @@
 
 	if (!nvic_irq_domain) {
 		pr_warn("Failed to allocate irq domain\n");
+		iounmap(nvic_base);
 		return -ENOMEM;
 	}
 
@@ -101,6 +102,7 @@
 	if (ret) {
 		pr_warn("Failed to allocate irq chips\n");
 		irq_domain_remove(nvic_irq_domain);
+		iounmap(nvic_base);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-or1k-pic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-or1k-pic.c
@@ -66,7 +66,6 @@
 		.name = "or1k-PIC-level",
 		.irq_unmask = or1k_pic_unmask,
 		.irq_mask = or1k_pic_mask,
-		.irq_mask_ack = or1k_pic_mask_ack,
 	},
 	.handle = handle_level_irq,
 	.flags = IRQ_LEVEL | IRQ_NOPROBE,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-realtek-rtl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-realtek-rtl.c
@@ -62,7 +62,7 @@
 
 static int intc_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
 {
-	irq_set_chip_and_handler(hw, &realtek_ictl_irq, handle_level_irq);
+	irq_set_chip_and_handler(irq, &realtek_ictl_irq, handle_level_irq);
 
 	return 0;
 }
@@ -76,16 +76,20 @@
 {
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	struct irq_domain *domain;
-	unsigned int pending;
+	unsigned long pending;
+	unsigned int soc_int;
 
 	chained_irq_enter(chip, desc);
 	pending = readl(REG(RTL_ICTL_GIMR)) & readl(REG(RTL_ICTL_GISR));
+
 	if (unlikely(!pending)) {
 		spurious_interrupt();
 		goto out;
 	}
+
 	domain = irq_desc_get_handler_data(desc);
-	generic_handle_domain_irq(domain, __ffs(pending));
+	for_each_set_bit(soc_int, &pending, 32)
+		generic_handle_domain_irq(domain, soc_int);
 
 out:
 	chained_irq_exit(chip, desc);
@@ -95,7 +99,8 @@
  * SoC interrupts are cascaded to MIPS CPU interrupts according to the
  * interrupt-map in the device tree. Each SoC interrupt gets 4 bits for
  * the CPU interrupt in an Interrupt Routing Register. Max 32 SoC interrupts
- * thus go into 4 IRRs.
+ * thus go into 4 IRRs. A routing value of '0' means the interrupt is left
+ * disconnected. Routing values {1..15} connect to output lines {0..14}.
  */
 static int __init map_interrupts(struct device_node *node, struct irq_domain *domain)
 {
@@ -129,12 +134,12 @@
 		if (!cpu_ictl)
 			return -EINVAL;
 		ret = of_property_read_u32(cpu_ictl, "#interrupt-cells", &tmp);
+		of_node_put(cpu_ictl);
 		if (ret || tmp != 1)
 			return -EINVAL;
-		of_node_put(cpu_ictl);
 
 		cpu_int = be32_to_cpup(imap + 2);
-		if (cpu_int > 7)
+		if (cpu_int > 7 || cpu_int < 2)
 			return -EINVAL;
 
 		if (!(mips_irqs_set & BIT(cpu_int))) {
@@ -143,7 +148,8 @@
 			mips_irqs_set |= BIT(cpu_int);
 		}
 
-		regs[(soc_int * 4) / 32] |= cpu_int << (soc_int * 4) % 32;
+		/* Use routing values (1..6) for CPU interrupts (2..7) */
+		regs[(soc_int * 4) / 32] |= (cpu_int - 1) << (soc_int * 4) % 32;
 		imap += 3;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-riscv-intc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-riscv-intc.c
@@ -109,8 +109,16 @@
 	 * for each INTC DT node. We only need to do INTC initialization
 	 * for the INTC DT node belonging to boot CPU (or boot HART).
 	 */
-	if (riscv_hartid_to_cpuid(hartid) != smp_processor_id())
+	if (riscv_hartid_to_cpuid(hartid) != smp_processor_id()) {
+		/*
+		 * The INTC nodes of each CPU are suppliers for downstream
+		 * interrupt controllers (such as PLIC, IMSIC and APLIC
+		 * direct-mode) so we should mark an INTC node as initialized
+		 * if we are not creating IRQ domain for it.
+		 */
+		fwnode_dev_initialized(of_fwnode_handle(node), true);
 		return 0;
+	}
 
 	intc_domain = irq_domain_add_linear(node, BITS_PER_LONG,
 					    &riscv_intc_domain_ops, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-sifive-plic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-sifive-plic.c
@@ -163,7 +163,13 @@
 {
 	struct plic_handler *handler = this_cpu_ptr(&plic_handlers);
 
-	writel(d->hwirq, handler->hart_base + CONTEXT_CLAIM);
+	if (irqd_irq_masked(d)) {
+		plic_irq_unmask(d);
+		writel(d->hwirq, handler->hart_base + CONTEXT_CLAIM);
+		plic_irq_mask(d);
+	} else {
+		writel(d->hwirq, handler->hart_base + CONTEXT_CLAIM);
+	}
 }
 
 static struct irq_chip plic_chip = {
@@ -392,3 +398,4 @@
 
 IRQCHIP_DECLARE(sifive_plic, "sifive,plic-1.0.0", plic_init);
 IRQCHIP_DECLARE(riscv_plic0, "riscv,plic0", plic_init); /* for legacy systems */
+IRQCHIP_DECLARE(thead_c900_plic, "thead,c900-plic", plic_init); /* for firmware driver */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-sni-exiu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-sni-exiu.c
@@ -37,11 +37,26 @@
 	u32		spi_base;
 };
 
-static void exiu_irq_eoi(struct irq_data *d)
+static void exiu_irq_ack(struct irq_data *d)
 {
 	struct exiu_irq_data *data = irq_data_get_irq_chip_data(d);
 
 	writel(BIT(d->hwirq), data->base + EIREQCLR);
+}
+
+static void exiu_irq_eoi(struct irq_data *d)
+{
+	struct exiu_irq_data *data = irq_data_get_irq_chip_data(d);
+
+	/*
+	 * Level triggered interrupts are latched and must be cleared during
+	 * EOI or the interrupt will be jammed on. Of course if a level
+	 * triggered interrupt is still asserted then the write will not clear
+	 * the interrupt.
+	 */
+	if (irqd_is_level_type(d))
+		writel(BIT(d->hwirq), data->base + EIREQCLR);
+
 	irq_chip_eoi_parent(d);
 }
 
@@ -91,10 +106,13 @@
 	writel_relaxed(val, data->base + EILVL);
 
 	val = readl_relaxed(data->base + EIEDG);
-	if (type == IRQ_TYPE_LEVEL_LOW || type == IRQ_TYPE_LEVEL_HIGH)
+	if (type == IRQ_TYPE_LEVEL_LOW || type == IRQ_TYPE_LEVEL_HIGH) {
 		val &= ~BIT(d->hwirq);
-	else
+		irq_set_handler_locked(d, handle_fasteoi_irq);
+	} else {
 		val |= BIT(d->hwirq);
+		irq_set_handler_locked(d, handle_fasteoi_ack_irq);
+	}
 	writel_relaxed(val, data->base + EIEDG);
 
 	writel_relaxed(BIT(d->hwirq), data->base + EIREQCLR);
@@ -104,6 +122,7 @@
 
 static struct irq_chip exiu_irq_chip = {
 	.name			= "EXIU",
+	.irq_ack		= exiu_irq_ack,
 	.irq_eoi		= exiu_irq_eoi,
 	.irq_enable		= exiu_irq_enable,
 	.irq_mask		= exiu_irq_mask,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-stm32-exti.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-stm32-exti.c
@@ -408,6 +408,7 @@
 	.map	= irq_map_generic_chip,
 	.alloc  = stm32_exti_alloc,
 	.free	= stm32_exti_free,
+	.xlate	= irq_domain_xlate_twocell,
 };
 
 static void stm32_irq_ack(struct irq_data *d)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-sunxi-nmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-sunxi-nmi.c
@@ -187,7 +187,8 @@
 	gc->chip_types[0].chip.irq_unmask	= irq_gc_mask_set_bit;
 	gc->chip_types[0].chip.irq_eoi		= irq_gc_ack_set_bit;
 	gc->chip_types[0].chip.irq_set_type	= sunxi_sc_nmi_set_type;
-	gc->chip_types[0].chip.flags		= IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED;
+	gc->chip_types[0].chip.flags		= IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED |
+						  IRQCHIP_SKIP_SET_WAKE;
 	gc->chip_types[0].regs.ack		= reg_offs->pend;
 	gc->chip_types[0].regs.mask		= reg_offs->enable;
 	gc->chip_types[0].regs.type		= reg_offs->ctrl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-tegra.c
@@ -148,10 +148,10 @@
 		lic->cop_iep[i] = readl_relaxed(ictlr + ICTLR_COP_IEP_CLASS);
 
 		/* Disable COP interrupts */
-		writel_relaxed(~0ul, ictlr + ICTLR_COP_IER_CLR);
+		writel_relaxed(GENMASK(31, 0), ictlr + ICTLR_COP_IER_CLR);
 
 		/* Disable CPU interrupts */
-		writel_relaxed(~0ul, ictlr + ICTLR_CPU_IER_CLR);
+		writel_relaxed(GENMASK(31, 0), ictlr + ICTLR_CPU_IER_CLR);
 
 		/* Enable the wakeup sources of ictlr */
 		writel_relaxed(lic->ictlr_wake_mask[i], ictlr + ICTLR_CPU_IER_SET);
@@ -172,12 +172,12 @@
 
 		writel_relaxed(lic->cpu_iep[i],
 			       ictlr + ICTLR_CPU_IEP_CLASS);
-		writel_relaxed(~0ul, ictlr + ICTLR_CPU_IER_CLR);
+		writel_relaxed(GENMASK(31, 0), ictlr + ICTLR_CPU_IER_CLR);
 		writel_relaxed(lic->cpu_ier[i],
 			       ictlr + ICTLR_CPU_IER_SET);
 		writel_relaxed(lic->cop_iep[i],
 			       ictlr + ICTLR_COP_IEP_CLASS);
-		writel_relaxed(~0ul, ictlr + ICTLR_COP_IER_CLR);
+		writel_relaxed(GENMASK(31, 0), ictlr + ICTLR_COP_IER_CLR);
 		writel_relaxed(lic->cop_ier[i],
 			       ictlr + ICTLR_COP_IER_SET);
 	}
@@ -312,7 +312,7 @@
 		lic->base[i] = base;
 
 		/* Disable all interrupts */
-		writel_relaxed(~0UL, base + ICTLR_CPU_IER_CLR);
+		writel_relaxed(GENMASK(31, 0), base + ICTLR_CPU_IER_CLR);
 		/* All interrupts target IRQ */
 		writel_relaxed(0, base + ICTLR_CPU_IEP_CLASS);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-ti-sci-intr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-ti-sci-intr.c
@@ -236,6 +236,7 @@
 	}
 
 	parent_domain = irq_find_host(parent_node);
+	of_node_put(parent_node);
 	if (!parent_domain) {
 		dev_err(dev, "Failed to find IRQ parent domain\n");
 		return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-wpcm450-aic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-wpcm450-aic.c
@@ -146,6 +146,7 @@
 	aic->regs = of_iomap(node, 0);
 	if (!aic->regs) {
 		pr_err("Failed to map WPCM450 AIC registers\n");
+		kfree(aic);
 		return -ENOMEM;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-xilinx-intc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-xilinx-intc.c
@@ -18,6 +18,8 @@
 #include <linux/jump_label.h>
 #include <linux/bug.h>
 #include <linux/of_irq.h>
+#include <linux/cpuhotplug.h>
+#include <linux/smp.h>
 
 /* No one else should require these constants, so define them locally here. */
 #define ISR 0x00			/* Interrupt Status Register */
@@ -32,26 +34,34 @@
 #define MER_ME (1<<0)
 #define MER_HIE (1<<1)
 
-static DEFINE_STATIC_KEY_FALSE(xintc_is_be);
-
 struct xintc_irq_chip {
 	void		__iomem *base;
-	struct		irq_domain *root_domain;
+	struct		irq_domain *domain;
 	u32		intr_mask;
-	u32		nr_irq;
+	struct			irq_chip *intc_dev;
+	u32				nr_irq;
+	u32				sw_irq;
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+	int				irq;
+#endif
 };
 
-static struct xintc_irq_chip *primary_intc;
+static DEFINE_STATIC_KEY_FALSE(xintc_is_be);
+
+static DEFINE_PER_CPU(struct xintc_irq_chip, primary_intc);
 
 static void xintc_write(struct xintc_irq_chip *irqc, int reg, u32 data)
 {
+	if (!irqc)
+		irqc = per_cpu_ptr(&primary_intc, smp_processor_id());
+
 	if (static_branch_unlikely(&xintc_is_be))
 		iowrite32be(data, irqc->base + reg);
 	else
 		iowrite32(data, irqc->base + reg);
 }
 
-static u32 xintc_read(struct xintc_irq_chip *irqc, int reg)
+static unsigned int xintc_read(struct xintc_irq_chip *irqc, int reg)
 {
 	if (static_branch_unlikely(&xintc_is_be))
 		return ioread32be(irqc->base + reg);
@@ -59,10 +69,30 @@
 		return ioread32(irqc->base + reg);
 }
 
+#if defined(CONFIG_SMP) && defined(CONFIG_MICROBLAZE)
+static DEFINE_RAW_SPINLOCK(ipi_lock);
+
+static void send_ipi(unsigned int cpu, unsigned int ipi_number)
+{
+	unsigned long flags;
+	struct xintc_irq_chip *irqc = per_cpu_ptr(&primary_intc, cpu);
+	u32 sw_irq = 1 << (ipi_number + irqc->nr_irq);
+
+	pr_debug("%s: cpu: %u, sends IPI: %d to cpu: %u, sw_irq %x\n",
+		 __func__, smp_processor_id(), ipi_number, cpu, sw_irq);
+
+	raw_spin_lock_irqsave(&ipi_lock, flags);
+
+	xintc_write(irqc, ISR, sw_irq);
+
+	raw_spin_unlock_irqrestore(&ipi_lock, flags);
+}
+#endif
+
 static void intc_enable_or_unmask(struct irq_data *d)
 {
-	struct xintc_irq_chip *irqc = irq_data_get_irq_chip_data(d);
-	unsigned long mask = BIT(d->hwirq);
+	unsigned long mask = 1 << d->hwirq;
+	struct xintc_irq_chip *local_intc = irq_data_get_irq_chip_data(d);
 
 	pr_debug("irq-xilinx: enable_or_unmask: %ld\n", d->hwirq);
 
@@ -71,73 +101,83 @@
 	 * acks the irq before calling the interrupt handler
 	 */
 	if (irqd_is_level_type(d))
-		xintc_write(irqc, IAR, mask);
+		xintc_write(local_intc, IAR, mask);
 
-	xintc_write(irqc, SIE, mask);
+	xintc_write(local_intc, SIE, mask);
 }
 
 static void intc_disable_or_mask(struct irq_data *d)
 {
-	struct xintc_irq_chip *irqc = irq_data_get_irq_chip_data(d);
+	struct xintc_irq_chip *local_intc = irq_data_get_irq_chip_data(d);
 
 	pr_debug("irq-xilinx: disable: %ld\n", d->hwirq);
-	xintc_write(irqc, CIE, BIT(d->hwirq));
+	xintc_write(local_intc, CIE, 1 << d->hwirq);
 }
 
 static void intc_ack(struct irq_data *d)
 {
-	struct xintc_irq_chip *irqc = irq_data_get_irq_chip_data(d);
+	struct xintc_irq_chip *local_intc = irq_data_get_irq_chip_data(d);
 
 	pr_debug("irq-xilinx: ack: %ld\n", d->hwirq);
-	xintc_write(irqc, IAR, BIT(d->hwirq));
+	xintc_write(local_intc, IAR, 1 << d->hwirq);
 }
 
 static void intc_mask_ack(struct irq_data *d)
 {
-	struct xintc_irq_chip *irqc = irq_data_get_irq_chip_data(d);
-	unsigned long mask = BIT(d->hwirq);
+	unsigned long mask = 1 << d->hwirq;
+	struct xintc_irq_chip *local_intc = irq_data_get_irq_chip_data(d);
 
 	pr_debug("irq-xilinx: disable_and_ack: %ld\n", d->hwirq);
-	xintc_write(irqc, CIE, mask);
-	xintc_write(irqc, IAR, mask);
-}
-
-static struct irq_chip intc_dev = {
-	.name = "Xilinx INTC",
-	.irq_unmask = intc_enable_or_unmask,
-	.irq_mask = intc_disable_or_mask,
-	.irq_ack = intc_ack,
-	.irq_mask_ack = intc_mask_ack,
-};
-
-unsigned int xintc_get_irq(void)
-{
-	unsigned int irq = -1;
-	u32 hwirq;
-
-	hwirq = xintc_read(primary_intc, IVR);
-	if (hwirq != -1U)
-		irq = irq_find_mapping(primary_intc->root_domain, hwirq);
-
-	pr_debug("irq-xilinx: hwirq=%d, irq=%d\n", hwirq, irq);
-
-	return irq;
+	xintc_write(local_intc, CIE, mask);
+	xintc_write(local_intc, IAR, mask);
 }
 
 static int xintc_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
 {
-	struct xintc_irq_chip *irqc = d->host_data;
+	struct xintc_irq_chip *local_intc = d->host_data;
+	u32 edge = local_intc->intr_mask & (1 << hw);
+
+	/*
+	 * Find out which irq_domain this IRQ is assigned to. If it is assigned
+	 * to root domain then do not fill chip_data and set it up in the code
+	 */
+	if (irq_get_default_host() != d)
+		irq_set_chip_data(irq, local_intc);
+	else {
+		local_intc = per_cpu_ptr(&primary_intc, 0);
+		irq_set_chip_data(irq, NULL);
+	}
 
-	if (irqc->intr_mask & BIT(hw)) {
-		irq_set_chip_and_handler_name(irq, &intc_dev,
-					      handle_edge_irq, "edge");
+	if (edge) {
+#if defined(CONFIG_SMP) && defined(CONFIG_MICROBLAZE)
+		irq_set_chip_and_handler_name(irq, local_intc->intc_dev,
+			handle_percpu_irq, "percpu");
+#else
+		irq_set_chip_and_handler_name(irq, local_intc->intc_dev,
+						handle_edge_irq, "edge");
+#endif
 		irq_clear_status_flags(irq, IRQ_LEVEL);
 	} else {
-		irq_set_chip_and_handler_name(irq, &intc_dev,
-					      handle_level_irq, "level");
+#if defined(CONFIG_SMP) && defined(CONFIG_MICROBLAZE)
+		irq_set_chip_and_handler_name(irq, local_intc->intc_dev,
+			handle_percpu_irq, "percpu");
+#else
+		irq_set_chip_and_handler_name(irq, local_intc->intc_dev,
+						handle_level_irq, "level");
+#endif
 		irq_set_status_flags(irq, IRQ_LEVEL);
 	}
-	irq_set_chip_data(irq, irqc);
+
+	/*
+	 * Setup all IRQs to be per CPU because servicing it by different
+	 * cpu is not implemented yet. And for uniprocessor system this flag
+	 * is nop all time.
+	 */
+	irq_set_status_flags(irq, IRQ_PER_CPU);
+
+	pr_debug("cpu: %u, xintc_map: hwirq=%u, irq=%u, edge=%u\n",
+		 smp_processor_id(), (u32)hw, irq, edge);
+
 	return 0;
 }
 
@@ -146,33 +186,134 @@
 	.map = xintc_map,
 };
 
+static void xil_intc_initial_setup(struct xintc_irq_chip *irqc)
+{
+	int i;
+	u32 mask;
+
+	/*
+	 * Disable all external interrupts until they are
+	 * explicity requested.
+	 */
+	xintc_write(irqc, IER, 0);
+
+	/* Acknowledge any pending interrupts just in case. */
+	xintc_write(irqc, IAR, 0xffffffff);
+
+	/* Turn on the Master Enable. */
+	xintc_write(irqc, MER, MER_HIE | MER_ME);
+	if (!(xintc_read(irqc, MER) & (MER_HIE | MER_ME))) {
+		static_branch_enable(&xintc_is_be);
+		xintc_write(irqc, MER, MER_HIE | MER_ME);
+	}
+
+	/* Enable all SW IRQs */
+	for (i = 0; i < irqc->sw_irq; i++) {
+		mask = 1 << (i + irqc->nr_irq);
+		xintc_write(irqc, IAR, mask);
+		xintc_write(irqc, SIE, mask);
+	}
+}
+
 static void xil_intc_irq_handler(struct irq_desc *desc)
 {
 	struct irq_chip *chip = irq_desc_get_chip(desc);
-	struct xintc_irq_chip *irqc;
+	struct xintc_irq_chip *irqc =
+		irq_data_get_irq_handler_data(&desc->irq_data);
 
-	irqc = irq_data_get_irq_handler_data(&desc->irq_data);
 	chained_irq_enter(chip, desc);
+
 	do {
 		u32 hwirq = xintc_read(irqc, IVR);
 
 		if (hwirq == -1U)
 			break;
 
-		generic_handle_domain_irq(irqc->root_domain, hwirq);
+		generic_handle_domain_irq(irqc->domain, hwirq);
 	} while (true);
 	chained_irq_exit(chip, desc);
 }
 
+static int xil_intc_start(unsigned int cpu)
+{
+	struct xintc_irq_chip *irqc = per_cpu_ptr(&primary_intc, cpu);
+
+	pr_debug("%s: intc cpu %d\n", __func__, cpu);
+
+	xil_intc_initial_setup(irqc);
+
+	return 0;
+}
+
+static int xil_intc_stop(unsigned int cpu)
+{
+	pr_debug("%s: intc cpu %d\n", __func__, cpu);
+
+	return 0;
+}
+
+static void xil_intc_handle_irq(struct pt_regs *regs)
+{
+	int ret;
+	unsigned int hwirq, cpu_id = smp_processor_id();
+	struct xintc_irq_chip *irqc = per_cpu_ptr(&primary_intc, cpu_id);
+
+	do {
+		hwirq = xintc_read(irqc, IVR);
+		if (hwirq != -1U) {
+			if (hwirq >= irqc->nr_irq) {
+#if defined(CONFIG_SMP) && defined(CONFIG_MICROBLAZE)
+				handle_IPI(hwirq - irqc->nr_irq, regs);
+#else
+				WARN_ONCE(1, "SW interrupt not handled\n");
+#endif
+				/* ACK is necessary */
+				xintc_write(irqc, IAR, 1 << hwirq);
+				continue;
+			} else {
+				ret = handle_domain_irq(irqc->domain,
+							hwirq, regs);
+				WARN_ONCE(ret, "cpu %d: Unhandled HWIRQ %d\n",
+					  cpu_id, hwirq);
+				continue;
+			}
+		}
+
+		break;
+	} while (1);
+}
+
+#ifndef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
 static int __init xilinx_intc_of_init(struct device_node *intc,
 					     struct device_node *parent)
+#else
+static int xilinx_intc_of_init(struct device_node *intc,
+			       struct device_node *parent)
+#endif
 {
-	struct xintc_irq_chip *irqc;
 	int ret, irq;
+	struct xintc_irq_chip *irqc;
+	struct irq_chip *intc_dev;
+	u32 cpu_id = 0;
+
+	ret = of_property_read_u32(intc, "cpu-id", &cpu_id);
+	if (ret < 0)
+		pr_debug("%s: %pOF: cpu_id not found\n", __func__, intc);
+
+	/* No parent means it is primary intc */
+	if (!parent) {
+		irqc = per_cpu_ptr(&primary_intc, cpu_id);
+		if (irqc->base) {
+			pr_err("%pOF: %s: cpu %d has already irq controller\n",
+				intc, __func__, cpu_id);
+			return -EINVAL;
+		}
+	} else {
+		irqc = kzalloc(sizeof(*irqc), GFP_KERNEL);
+		if (!irqc)
+			return -ENOMEM;
+	}
 
-	irqc = kzalloc(sizeof(*irqc), GFP_KERNEL);
-	if (!irqc)
-		return -ENOMEM;
 	irqc->base = of_iomap(intc, 0);
 	BUG_ON(!irqc->base);
 
@@ -188,39 +329,48 @@
 		irqc->intr_mask = 0;
 	}
 
-	if (irqc->intr_mask >> irqc->nr_irq)
+	if ((u64)irqc->intr_mask >> irqc->nr_irq)
 		pr_warn("irq-xilinx: mismatch in kind-of-intr param\n");
 
-	pr_info("irq-xilinx: %pOF: num_irq=%d, edge=0x%x\n",
-		intc, irqc->nr_irq, irqc->intr_mask);
-
+	/* sw irqs are optinal */
+	of_property_read_u32(intc, "xlnx,num-sw-intr", &irqc->sw_irq);
 
-	/*
-	 * Disable all external interrupts until they are
-	 * explicitly requested.
-	 */
-	xintc_write(irqc, IER, 0);
+	pr_info("irq-xilinx: %pOF: num_irq=%d, sw_irq=%d, edge=0x%x\n",
+		intc, irqc->nr_irq, irqc->sw_irq, irqc->intr_mask);
 
-	/* Acknowledge any pending interrupts just in case. */
-	xintc_write(irqc, IAR, 0xffffffff);
+	/* Right now enable only SW IRQs on that IP and wait */
+	if (cpu_id) {
+		xil_intc_initial_setup(irqc);
+		return 0;
+	}
 
-	/* Turn on the Master Enable. */
-	xintc_write(irqc, MER, MER_HIE | MER_ME);
-	if (xintc_read(irqc, MER) != (MER_HIE | MER_ME)) {
-		static_branch_enable(&xintc_is_be);
-		xintc_write(irqc, MER, MER_HIE | MER_ME);
+	intc_dev = kzalloc(sizeof(*intc_dev), GFP_KERNEL);
+	if (!intc_dev) {
+		ret = -ENOMEM;
+		goto error;
 	}
 
-	irqc->root_domain = irq_domain_add_linear(intc, irqc->nr_irq,
+	intc_dev->name = intc->full_name;
+	intc_dev->irq_unmask = intc_enable_or_unmask,
+	intc_dev->irq_mask = intc_disable_or_mask,
+	intc_dev->irq_ack = intc_ack,
+	intc_dev->irq_mask_ack = intc_mask_ack,
+	irqc->intc_dev = intc_dev;
+
+	irqc->domain = irq_domain_add_linear(intc, irqc->nr_irq,
 						  &xintc_irq_domain_ops, irqc);
-	if (!irqc->root_domain) {
+	if (!irqc->domain) {
 		pr_err("irq-xilinx: Unable to create IRQ domain\n");
 		ret = -EINVAL;
-		goto error;
+		goto err_alloc;
 	}
 
 	if (parent) {
 		irq = irq_of_parse_and_map(intc, 0);
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+		irqc->irq = irq;
+		intc->data = irqc;
+#endif
 		if (irq) {
 			irq_set_chained_handler_and_data(irq,
 							 xil_intc_irq_handler,
@@ -228,21 +378,95 @@
 		} else {
 			pr_err("irq-xilinx: interrupts property not in DT\n");
 			ret = -EINVAL;
-			goto error;
+			goto err_alloc;
 		}
-	} else {
-		primary_intc = irqc;
-		irq_set_default_host(primary_intc->root_domain);
+		xil_intc_initial_setup(irqc);
+		return 0;
 	}
 
-	return 0;
+	/*
+	 * Set default domain here because for other root intc
+	 * irq_find_mapping() will use irq_default_domain as fallback
+	 */
+	irq_set_default_host(irqc->domain);
+	set_handle_irq(xil_intc_handle_irq);
 
+	ret = cpuhp_setup_state(CPUHP_AP_IRQ_XILINX_STARTING,
+				"microblaze/arch_intc:starting",
+				xil_intc_start, xil_intc_stop);
+
+#if defined(CONFIG_SMP) && defined(CONFIG_MICROBLAZE)
+	set_smp_cross_call(send_ipi);
+#endif
+
+	return ret;
+
+err_alloc:
+	kfree(intc_dev);
 error:
 	iounmap(irqc->base);
-	kfree(irqc);
+	if (parent)
+		kfree(irqc);
 	return ret;
+}
+
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+static int xilinx_intc_of_remove(struct device_node *intc,
+				 struct device_node *parent)
+{
+	int irq;
+	struct xintc_irq_chip *irqc;
 
+	if (!parent)
+		return 0;
+
+	irqc = intc->data;
+	irq = irqc->irq;
+
+	irq_set_chained_handler_and_data(irq, NULL, NULL);
+
+	if (irqc->domain) {
+		unsigned int tempirq;
+		unsigned int i;
+
+		for (i = 0; i < irqc->domain->mapcount; i++) {
+			tempirq = irq_find_mapping(irqc->domain, i);
+			if (tempirq)
+				irq_dispose_mapping(tempirq);
+		}
+		irq_dispose_mapping(irq);
+		irq_domain_remove(irqc->domain);
+	}
+
+	/*
+	 * Disable all external interrupts until they are
+	 * explicity requested.
+	 */
+	xintc_write(irqc, IER, 0);
+	/* Acknowledge any pending interrupts just in case. */
+	xintc_write(irqc, IAR, 0xffffffff);
+	/* Turn off the Master Enable. */
+	xintc_write(irqc, MER, 0x0);
+
+	iounmap(irqc->base);
+	kfree(irqc);
+
+	return 0;
 }
 
+static struct irqc_init_remove_funps intc_funps = {
+	.irqchip_initp = xilinx_intc_of_init,
+	.irqchip_removep = xilinx_intc_of_remove,
+};
+
+IRQCHIP_PLATFORM_DRIVER_BEGIN(xilinx_intc_xps)
+IRQCHIP_MATCH("xlnx,xps-intc-1.00.a", &intc_funps)
+IRQCHIP_PLATFORM_DRIVER_END(xilinx_intc_xps)
+
+IRQCHIP_PLATFORM_DRIVER_BEGIN(xilinx_intc_opb)
+IRQCHIP_MATCH("xlnx,opb-intc-1.00.c", &intc_funps)
+IRQCHIP_PLATFORM_DRIVER_END(xilinx_intc_opb)
+#else
 IRQCHIP_DECLARE(xilinx_intc_xps, "xlnx,xps-intc-1.00.a", xilinx_intc_of_init);
 IRQCHIP_DECLARE(xilinx_intc_opb, "xlnx,opb-intc-1.00.c", xilinx_intc_of_init);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irq-xtensa-mx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irq-xtensa-mx.c
@@ -151,14 +151,25 @@
 	.irq_set_affinity = xtensa_mx_irq_set_affinity,
 };
 
+static void __init xtensa_mx_init_common(struct irq_domain *root_domain)
+{
+	unsigned int i;
+
+	irq_set_default_host(root_domain);
+	secondary_init_irq();
+
+	/* Initialize default IRQ routing to CPU 0 */
+	for (i = 0; i < XCHAL_NUM_EXTINTERRUPTS; ++i)
+		set_er(1, MIROUT(i));
+}
+
 int __init xtensa_mx_init_legacy(struct device_node *interrupt_parent)
 {
 	struct irq_domain *root_domain =
 		irq_domain_add_legacy(NULL, NR_IRQS - 1, 1, 0,
 				&xtensa_mx_irq_domain_ops,
 				&xtensa_mx_irq_chip);
-	irq_set_default_host(root_domain);
-	secondary_init_irq();
+	xtensa_mx_init_common(root_domain);
 	return 0;
 }
 
@@ -168,8 +179,7 @@
 	struct irq_domain *root_domain =
 		irq_domain_add_linear(np, NR_IRQS, &xtensa_mx_irq_domain_ops,
 				&xtensa_mx_irq_chip);
-	irq_set_default_host(root_domain);
-	secondary_init_irq();
+	xtensa_mx_init_common(root_domain);
 	return 0;
 }
 IRQCHIP_DECLARE(xtensa_mx_irq_chip, "cdns,xtensa-mx", xtensa_mx_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/irqchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/irqchip.c
@@ -15,6 +15,14 @@
 #include <linux/irqchip.h>
 #include <linux/platform_device.h>
 
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+struct platform_irqchip_instance {
+	of_irq_init_cb_t irq_init_cb;
+	of_irq_remove_cb_t irq_remove_cb;
+	struct device_node *parent_node;
+};
+#endif
+
 /*
  * This special of_device_id is the sentinel at the end of the
  * of_device_id[] array of all irqchips. It is automatically placed at
@@ -32,14 +40,17 @@
 	acpi_probe_device_table(irqchip);
 }
 
+#ifndef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
 int platform_irqchip_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
 	struct device_node *par_np = of_irq_find_parent(np);
 	of_irq_init_cb_t irq_init_cb = of_device_get_match_data(&pdev->dev);
 
-	if (!irq_init_cb)
+	if (!irq_init_cb) {
+		of_node_put(par_np);
 		return -EINVAL;
+	}
 
 	if (par_np == np)
 		par_np = NULL;
@@ -52,9 +63,67 @@
 	 * interrupt controller. The actual initialization callback of this
 	 * interrupt controller can check for specific domains as necessary.
 	 */
-	if (par_np && !irq_find_matching_host(par_np, DOMAIN_BUS_ANY))
+	if (par_np && !irq_find_matching_host(par_np, DOMAIN_BUS_ANY)) {
+		of_node_put(par_np);
 		return -EPROBE_DEFER;
+	}
 
 	return irq_init_cb(np, par_np);
 }
 EXPORT_SYMBOL_GPL(platform_irqchip_probe);
+#else
+int platform_irqchip_probe(struct platform_device *pdev)
+{
+	struct platform_irqchip_instance *irqchip;
+	const struct irqc_init_remove_funps *irqchip_funps;
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *par_np = of_irq_find_parent(np);
+
+	irqchip = devm_kzalloc(&pdev->dev, sizeof(*irqchip), GFP_KERNEL);
+	if (!irqchip)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, irqchip);
+
+	irqchip_funps = of_device_get_match_data(&pdev->dev);
+	irqchip->irq_init_cb =	irqchip_funps->irqchip_initp;
+	irqchip->irq_remove_cb = irqchip_funps->irqchip_removep;
+	irqchip->parent_node = par_np;
+
+	if (!irqchip->irq_init_cb)
+		return -EINVAL;
+
+	if (par_np == np)
+		par_np = NULL;
+
+	/*
+	 * If there's a parent interrupt controller and  none of the parent irq
+	 * domains have been registered, that means the parent interrupt
+	 * controller has not been initialized yet.  it's not time for this
+	 * interrupt controller to initialize. So, defer probe of this
+	 * interrupt controller. The actual initialization callback of this
+	 * interrupt controller can check for specific domains as necessary.
+	 */
+	if (par_np && !irq_find_matching_host(par_np, DOMAIN_BUS_ANY))
+		return -EPROBE_DEFER;
+
+	return irqchip->irq_init_cb(np, par_np);
+}
+EXPORT_SYMBOL_GPL(platform_irqchip_probe);
+
+int platform_irqchip_remove(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct platform_irqchip_instance *irqchip = platform_get_drvdata(pdev);
+	struct device_node *par_np = irqchip->parent_node;
+
+	if (!irqchip->irq_remove_cb)
+		return -EINVAL;
+
+	if (par_np == np)
+		par_np = NULL;
+
+	return irqchip->irq_remove_cb(np, par_np);
+}
+EXPORT_SYMBOL_GPL(platform_irqchip_remove);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/irqchip/qcom-pdc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/irqchip/qcom-pdc.c
@@ -56,17 +56,18 @@
 static void pdc_enable_intr(struct irq_data *d, bool on)
 {
 	int pin_out = d->hwirq;
+	unsigned long flags;
 	u32 index, mask;
 	u32 enable;
 
 	index = pin_out / 32;
 	mask = pin_out % 32;
 
-	raw_spin_lock(&pdc_lock);
+	raw_spin_lock_irqsave(&pdc_lock, flags);
 	enable = pdc_reg_read(IRQ_ENABLE_BANK, index);
 	enable = on ? ENABLE_INTR(enable, mask) : CLEAR_INTR(enable, mask);
 	pdc_reg_write(IRQ_ENABLE_BANK, index, enable);
-	raw_spin_unlock(&pdc_lock);
+	raw_spin_unlock_irqrestore(&pdc_lock, flags);
 }
 
 static void qcom_pdc_gic_disable(struct irq_data *d)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/hardware/mISDN/hfcmulti.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/hardware/mISDN/hfcmulti.c
@@ -1931,7 +1931,7 @@
 static void
 hfcmulti_tx(struct hfc_multi *hc, int ch)
 {
-	int i, ii, temp, len = 0;
+	int i, ii, temp, tmp_len, len = 0;
 	int Zspace, z1, z2; /* must be int for calculation */
 	int Fspace, f1, f2;
 	u_char *d;
@@ -2152,14 +2152,15 @@
 		HFC_wait_nodebug(hc);
 	}
 
+	tmp_len = (*sp)->len;
 	dev_kfree_skb(*sp);
 	/* check for next frame */
 	if (bch && get_next_bframe(bch)) {
-		len = (*sp)->len;
+		len = tmp_len;
 		goto next_frame;
 	}
 	if (dch && get_next_dframe(dch)) {
-		len = (*sp)->len;
+		len = tmp_len;
 		goto next_frame;
 	}
 
@@ -3217,6 +3218,7 @@
 hfcm_l1callback(struct dchannel *dch, u_int cmd)
 {
 	struct hfc_multi	*hc = dch->hw;
+	struct sk_buff_head	free_queue;
 	u_long	flags;
 
 	switch (cmd) {
@@ -3245,6 +3247,7 @@
 		l1_event(dch->l1, HW_POWERUP_IND);
 		break;
 	case HW_DEACT_REQ:
+		__skb_queue_head_init(&free_queue);
 		/* start deactivation */
 		spin_lock_irqsave(&hc->lock, flags);
 		if (hc->ctype == HFC_TYPE_E1) {
@@ -3264,20 +3267,21 @@
 				plxsd_checksync(hc, 0);
 			}
 		}
-		skb_queue_purge(&dch->squeue);
+		skb_queue_splice_init(&dch->squeue, &free_queue);
 		if (dch->tx_skb) {
-			dev_kfree_skb(dch->tx_skb);
+			__skb_queue_tail(&free_queue, dch->tx_skb);
 			dch->tx_skb = NULL;
 		}
 		dch->tx_idx = 0;
 		if (dch->rx_skb) {
-			dev_kfree_skb(dch->rx_skb);
+			__skb_queue_tail(&free_queue, dch->rx_skb);
 			dch->rx_skb = NULL;
 		}
 		test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
 		if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags))
 			del_timer(&dch->timer);
 		spin_unlock_irqrestore(&hc->lock, flags);
+		__skb_queue_purge(&free_queue);
 		break;
 	case HW_POWERUP_REQ:
 		spin_lock_irqsave(&hc->lock, flags);
@@ -3384,6 +3388,9 @@
 	case PH_DEACTIVATE_REQ:
 		test_and_clear_bit(FLG_L2_ACTIVATED, &dch->Flags);
 		if (dch->dev.D.protocol != ISDN_P_TE_S0) {
+			struct sk_buff_head free_queue;
+
+			__skb_queue_head_init(&free_queue);
 			spin_lock_irqsave(&hc->lock, flags);
 			if (debug & DEBUG_HFCMULTI_MSG)
 				printk(KERN_DEBUG
@@ -3405,14 +3412,14 @@
 				/* deactivate */
 				dch->state = 1;
 			}
-			skb_queue_purge(&dch->squeue);
+			skb_queue_splice_init(&dch->squeue, &free_queue);
 			if (dch->tx_skb) {
-				dev_kfree_skb(dch->tx_skb);
+				__skb_queue_tail(&free_queue, dch->tx_skb);
 				dch->tx_skb = NULL;
 			}
 			dch->tx_idx = 0;
 			if (dch->rx_skb) {
-				dev_kfree_skb(dch->rx_skb);
+				__skb_queue_tail(&free_queue, dch->rx_skb);
 				dch->rx_skb = NULL;
 			}
 			test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
@@ -3424,6 +3431,7 @@
 #endif
 			ret = 0;
 			spin_unlock_irqrestore(&hc->lock, flags);
+			__skb_queue_purge(&free_queue);
 		} else
 			ret = l1_event(dch->l1, hh->prim);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/hardware/mISDN/hfcpci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/hardware/mISDN/hfcpci.c
@@ -839,7 +839,7 @@
 		*z1t = cpu_to_le16(new_z1);	/* now send data */
 		if (bch->tx_idx < bch->tx_skb->len)
 			return;
-		dev_kfree_skb(bch->tx_skb);
+		dev_kfree_skb_any(bch->tx_skb);
 		if (get_next_bframe(bch))
 			goto next_t_frame;
 		return;
@@ -895,7 +895,7 @@
 	}
 	bz->za[new_f1].z1 = cpu_to_le16(new_z1);	/* for next buffer */
 	bz->f1 = new_f1;	/* next frame */
-	dev_kfree_skb(bch->tx_skb);
+	dev_kfree_skb_any(bch->tx_skb);
 	get_next_bframe(bch);
 }
 
@@ -1119,7 +1119,7 @@
 	if (bch->tx_skb && bch->tx_idx < bch->tx_skb->len)
 		hfcpci_fill_fifo(bch);
 	else {
-		dev_kfree_skb(bch->tx_skb);
+		dev_kfree_skb_any(bch->tx_skb);
 		if (get_next_bframe(bch))
 			hfcpci_fill_fifo(bch);
 	}
@@ -1617,16 +1617,19 @@
 		test_and_clear_bit(FLG_L2_ACTIVATED, &dch->Flags);
 		spin_lock_irqsave(&hc->lock, flags);
 		if (hc->hw.protocol == ISDN_P_NT_S0) {
+			struct sk_buff_head free_queue;
+
+			__skb_queue_head_init(&free_queue);
 			/* prepare deactivation */
 			Write_hfc(hc, HFCPCI_STATES, 0x40);
-			skb_queue_purge(&dch->squeue);
+			skb_queue_splice_init(&dch->squeue, &free_queue);
 			if (dch->tx_skb) {
-				dev_kfree_skb(dch->tx_skb);
+				__skb_queue_tail(&free_queue, dch->tx_skb);
 				dch->tx_skb = NULL;
 			}
 			dch->tx_idx = 0;
 			if (dch->rx_skb) {
-				dev_kfree_skb(dch->rx_skb);
+				__skb_queue_tail(&free_queue, dch->rx_skb);
 				dch->rx_skb = NULL;
 			}
 			test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
@@ -1639,10 +1642,12 @@
 			hc->hw.mst_m &= ~HFCPCI_MASTER;
 			Write_hfc(hc, HFCPCI_MST_MODE, hc->hw.mst_m);
 			ret = 0;
+			spin_unlock_irqrestore(&hc->lock, flags);
+			__skb_queue_purge(&free_queue);
 		} else {
 			ret = l1_event(dch->l1, hh->prim);
+			spin_unlock_irqrestore(&hc->lock, flags);
 		}
-		spin_unlock_irqrestore(&hc->lock, flags);
 		break;
 	}
 	if (!ret)
@@ -2005,7 +2010,11 @@
 	}
 	/* Allocate memory for FIFOS */
 	/* the memory needs to be on a 32k boundary within the first 4G */
-	dma_set_mask(&hc->pdev->dev, 0xFFFF8000);
+	if (dma_set_mask(&hc->pdev->dev, 0xFFFF8000)) {
+		printk(KERN_WARNING
+		       "HFC-PCI: No usable DMA configuration!\n");
+		return -EIO;
+	}
 	buffer = dma_alloc_coherent(&hc->pdev->dev, 0x8000, &hc->hw.dmahandle,
 				    GFP_KERNEL);
 	/* We silently assume the address is okay if nonzero */
@@ -2268,7 +2277,7 @@
 		return 0;
 
 	if (hc->hw.int_m2 & HFCPCI_IRQ_ENABLE) {
-		spin_lock(&hc->lock);
+		spin_lock_irq(&hc->lock);
 		bch = Sel_BCS(hc, hc->hw.bswapped ? 2 : 1);
 		if (bch && bch->state == ISDN_P_B_RAW) { /* B1 rx&tx */
 			main_rec_hfcpci(bch);
@@ -2279,7 +2288,7 @@
 			main_rec_hfcpci(bch);
 			tx_birq(bch);
 		}
-		spin_unlock(&hc->lock);
+		spin_unlock_irq(&hc->lock);
 	}
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/hardware/mISDN/hfcsusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/hardware/mISDN/hfcsusb.c
@@ -326,20 +326,24 @@
 		test_and_clear_bit(FLG_L2_ACTIVATED, &dch->Flags);
 
 		if (hw->protocol == ISDN_P_NT_S0) {
+			struct sk_buff_head free_queue;
+
+			__skb_queue_head_init(&free_queue);
 			hfcsusb_ph_command(hw, HFC_L1_DEACTIVATE_NT);
 			spin_lock_irqsave(&hw->lock, flags);
-			skb_queue_purge(&dch->squeue);
+			skb_queue_splice_init(&dch->squeue, &free_queue);
 			if (dch->tx_skb) {
-				dev_kfree_skb(dch->tx_skb);
+				__skb_queue_tail(&free_queue, dch->tx_skb);
 				dch->tx_skb = NULL;
 			}
 			dch->tx_idx = 0;
 			if (dch->rx_skb) {
-				dev_kfree_skb(dch->rx_skb);
+				__skb_queue_tail(&free_queue, dch->rx_skb);
 				dch->rx_skb = NULL;
 			}
 			test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
 			spin_unlock_irqrestore(&hw->lock, flags);
+			__skb_queue_purge(&free_queue);
 #ifdef FIXME
 			if (test_and_clear_bit(FLG_L1_BUSY, &dch->Flags))
 				dchannel_sched_event(&hc->dch, D_CLEARBUSY);
@@ -1330,7 +1334,7 @@
 					printk("\n");
 				}
 
-				dev_kfree_skb(tx_skb);
+				dev_consume_skb_irq(tx_skb);
 				tx_skb = NULL;
 				if (fifo->dch && get_next_dframe(fifo->dch))
 					tx_skb = fifo->dch->tx_skb;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/hardware/mISDN/netjet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/hardware/mISDN/netjet.c
@@ -956,7 +956,7 @@
 	}
 	if (card->irq > 0)
 		free_irq(card->irq, card);
-	if (card->isac.dch.dev.dev.class)
+	if (device_is_registered(&card->isac.dch.dev.dev))
 		mISDN_unregister_device(&card->isac.dch.dev);
 
 	for (i = 0; i < 2; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/core.c
@@ -222,7 +222,7 @@
 
 	err = get_free_devid();
 	if (err < 0)
-		goto error1;
+		return err;
 	dev->id = err;
 
 	device_initialize(&dev->dev);
@@ -233,11 +233,12 @@
 	if (debug & DEBUG_CORE)
 		printk(KERN_DEBUG "mISDN_register %s %d\n",
 		       dev_name(&dev->dev), dev->id);
+	dev->dev.class = &mISDN_class;
+
 	err = create_stack(dev);
 	if (err)
 		goto error1;
 
-	dev->dev.class = &mISDN_class;
 	dev->dev.platform_data = dev;
 	dev->dev.parent = parent;
 	dev_set_drvdata(&dev->dev, dev);
@@ -249,8 +250,8 @@
 
 error3:
 	delete_stack(dev);
-	return err;
 error1:
+	put_device(&dev->dev);
 	return err;
 
 }
@@ -381,7 +382,7 @@
 	err = mISDN_inittimer(&debug);
 	if (err)
 		goto error2;
-	err = l1_init(&debug);
+	err = Isdnl1_Init(&debug);
 	if (err)
 		goto error3;
 	err = Isdnl2_Init(&debug);
@@ -395,7 +396,7 @@
 error5:
 	Isdnl2_cleanup();
 error4:
-	l1_cleanup();
+	Isdnl1_cleanup();
 error3:
 	mISDN_timer_cleanup();
 error2:
@@ -408,7 +409,7 @@
 {
 	misdn_sock_cleanup();
 	Isdnl2_cleanup();
-	l1_cleanup();
+	Isdnl1_cleanup();
 	mISDN_timer_cleanup();
 	class_unregister(&mISDN_class);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/core.h
@@ -60,8 +60,8 @@
 extern int	mISDN_inittimer(u_int *);
 extern void	mISDN_timer_cleanup(void);
 
-extern int	l1_init(u_int *);
-extern void	l1_cleanup(void);
+extern int	Isdnl1_Init(u_int *);
+extern void	Isdnl1_cleanup(void);
 extern int	Isdnl2_Init(u_int *);
 extern void	Isdnl2_cleanup(void);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/dsp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/dsp.h
@@ -247,7 +247,7 @@
 extern int dsp_cmx_conf(struct dsp *dsp, u32 conf_id);
 extern void dsp_cmx_receive(struct dsp *dsp, struct sk_buff *skb);
 extern void dsp_cmx_hdlc(struct dsp *dsp, struct sk_buff *skb);
-extern void dsp_cmx_send(void *arg);
+extern void dsp_cmx_send(struct timer_list *arg);
 extern void dsp_cmx_transmit(struct dsp *dsp, struct sk_buff *skb);
 extern int dsp_cmx_del_conf_member(struct dsp *dsp);
 extern int dsp_cmx_del_conf(struct dsp_conf *conf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/dsp_cmx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/dsp_cmx.c
@@ -1625,7 +1625,7 @@
 static int	dsp_count_valid; /* if we have last sample count */
 
 void
-dsp_cmx_send(void *arg)
+dsp_cmx_send(struct timer_list *arg)
 {
 	struct dsp_conf *conf;
 	struct dsp_conf_member *member;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/dsp_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/dsp_core.c
@@ -1195,7 +1195,7 @@
 	}
 
 	/* set sample timer */
-	timer_setup(&dsp_spl_tl, (void *)dsp_cmx_send, 0);
+	timer_setup(&dsp_spl_tl, dsp_cmx_send, 0);
 	dsp_spl_tl.expires = jiffies + dsp_tics;
 	dsp_spl_jiffies = dsp_spl_tl.expires;
 	add_timer(&dsp_spl_tl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/dsp_pipeline.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/dsp_pipeline.c
@@ -77,6 +77,7 @@
 	if (!entry)
 		return -ENOMEM;
 
+	INIT_LIST_HEAD(&entry->list);
 	entry->elem = elem;
 
 	entry->dev.class = elements_class;
@@ -107,7 +108,7 @@
 	device_unregister(&entry->dev);
 	return ret;
 err1:
-	kfree(entry);
+	put_device(&entry->dev);
 	return ret;
 }
 EXPORT_SYMBOL(mISDN_dsp_element_register);
@@ -192,7 +193,7 @@
 int dsp_pipeline_build(struct dsp_pipeline *pipeline, const char *cfg)
 {
 	int found = 0;
-	char *dup, *tok, *name, *args;
+	char *dup, *next, *tok, *name, *args;
 	struct dsp_element_entry *entry, *n;
 	struct dsp_pipeline_entry *pipeline_entry;
 	struct mISDN_dsp_element *elem;
@@ -203,10 +204,10 @@
 	if (!list_empty(&pipeline->list))
 		_dsp_pipeline_destroy(pipeline);
 
-	dup = kstrdup(cfg, GFP_ATOMIC);
+	dup = next = kstrdup(cfg, GFP_ATOMIC);
 	if (!dup)
 		return 0;
-	while ((tok = strsep(&dup, "|"))) {
+	while ((tok = strsep(&next, "|"))) {
 		if (!strlen(tok))
 			continue;
 		name = strsep(&tok, "(");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/l1oip.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/l1oip.h
@@ -59,6 +59,7 @@
 	int			bundle;		/* bundle channels in one frm */
 	int			codec;		/* codec to use for transmis. */
 	int			limit;		/* limit number of bchannels */
+	bool			shutdown;	/* if card is released */
 
 	/* timer */
 	struct timer_list	keep_tl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/l1oip_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/l1oip_core.c
@@ -275,7 +275,7 @@
 	p = frame;
 
 	/* restart timer */
-	if (time_before(hc->keep_tl.expires, jiffies + 5 * HZ))
+	if (time_before(hc->keep_tl.expires, jiffies + 5 * HZ) && !hc->shutdown)
 		mod_timer(&hc->keep_tl, jiffies + L1OIP_KEEPALIVE * HZ);
 	else
 		hc->keep_tl.expires = jiffies + L1OIP_KEEPALIVE * HZ;
@@ -601,7 +601,9 @@
 		goto multiframe;
 
 	/* restart timer */
-	if (time_before(hc->timeout_tl.expires, jiffies + 5 * HZ) || !hc->timeout_on) {
+	if ((time_before(hc->timeout_tl.expires, jiffies + 5 * HZ) ||
+	     !hc->timeout_on) &&
+	    !hc->shutdown) {
 		hc->timeout_on = 1;
 		mod_timer(&hc->timeout_tl, jiffies + L1OIP_TIMEOUT * HZ);
 	} else /* only adjust timer */
@@ -1232,11 +1234,10 @@
 {
 	int	ch;
 
-	if (timer_pending(&hc->keep_tl))
-		del_timer(&hc->keep_tl);
+	hc->shutdown = true;
 
-	if (timer_pending(&hc->timeout_tl))
-		del_timer(&hc->timeout_tl);
+	del_timer_sync(&hc->keep_tl);
+	del_timer_sync(&hc->timeout_tl);
 
 	cancel_work_sync(&hc->workq);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/isdn/mISDN/layer1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/isdn/mISDN/layer1.c
@@ -398,7 +398,7 @@
 EXPORT_SYMBOL(create_l1);
 
 int
-l1_init(u_int *deb)
+Isdnl1_Init(u_int *deb)
 {
 	debug = deb;
 	l1fsm_s.state_count = L1S_STATE_COUNT;
@@ -409,7 +409,7 @@
 }
 
 void
-l1_cleanup(void)
+Isdnl1_cleanup(void)
 {
 	mISDN_FsmFree(&l1fsm_s);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/Kconfig
@@ -59,6 +59,18 @@
 	  This option enables support for on-chip LED drivers found on Marvell
 	  Semiconductor 88PM8606 PMIC.
 
+config LEDS_AAEON
+	tristate "AAEON LED driver"
+	depends on X86
+	depends on UBUNTU_ODM_DRIVERS
+	select MFD_AAEON
+	help
+	  This led driver adds support for LED brightness control on Single
+	  Board Computers produced by AAEON.
+
+	  This driver leverages the ASUS WMI interface to access device
+	  resources.
+
 config LEDS_AN30259A
 	tristate "LED support for Panasonic AN30259A"
 	depends on LEDS_CLASS && I2C && OF
@@ -97,6 +109,7 @@
 config LEDS_AW2013
 	tristate "LED support for Awinic AW2013"
 	depends on LEDS_CLASS && I2C && OF
+	select REGMAP_I2C
 	help
 	  This option enables support for the AW2013 3-channel
 	  LED driver.
@@ -386,7 +399,6 @@
 	depends on OF
 	depends on I2C
 	select FW_LOADER
-	select FW_LOADER_USER_HELPER
 	help
 	  This option supports common operations for LP5521/5523/55231/5562/8501
 	  devices.
@@ -821,7 +833,7 @@
 config LEDS_TI_LMU_COMMON
 	tristate "LED driver for TI LMU"
 	depends on LEDS_CLASS
-	depends on REGMAP
+	select REGMAP
 	help
 	  Say Y to enable the LED driver for TI LMU devices.
 	  This supports common features between the TI LM3532, LM3631, LM3632,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/Makefile
@@ -9,6 +9,7 @@
 
 # LED Platform Drivers (keep this sorted, M-| sort)
 obj-$(CONFIG_LEDS_88PM860X)		+= leds-88pm860x.o
+obj-$(CONFIG_LEDS_AAEON)		+= leds-aaeon.o
 obj-$(CONFIG_LEDS_ACER_A500)		+= leds-acer-a500.o
 obj-$(CONFIG_LEDS_ADP5520)		+= leds-adp5520.o
 obj-$(CONFIG_LEDS_AN30259A)		+= leds-an30259a.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/flash/leds-lm3601x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/flash/leds-lm3601x.c
@@ -444,8 +444,6 @@
 {
 	struct lm3601x_led *led = i2c_get_clientdata(client);
 
-	mutex_destroy(&led->lock);
-
 	return regmap_update_bits(led->regmap, LM3601X_ENABLE_REG,
 			   LM3601X_ENABLE_MASK,
 			   LM3601X_MODE_STANDBY);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/flash/leds-sgm3140.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/flash/leds-sgm3140.c
@@ -114,8 +114,11 @@
 				"failed to enable regulator: %d\n", ret);
 			return ret;
 		}
+		gpiod_set_value_cansleep(priv->flash_gpio, 0);
 		gpiod_set_value_cansleep(priv->enable_gpio, 1);
 	} else {
+		del_timer_sync(&priv->powerdown_timer);
+		gpiod_set_value_cansleep(priv->flash_gpio, 0);
 		gpiod_set_value_cansleep(priv->enable_gpio, 0);
 		ret = regulator_disable(priv->vin_regulator);
 		if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/led-class-multicolor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/led-class-multicolor.c
@@ -6,6 +6,7 @@
 #include <linux/device.h>
 #include <linux/init.h>
 #include <linux/led-class-multicolor.h>
+#include <linux/math.h>
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/uaccess.h>
@@ -19,9 +20,10 @@
 	int i;
 
 	for (i = 0; i < mcled_cdev->num_colors; i++)
-		mcled_cdev->subled_info[i].brightness = brightness *
-					mcled_cdev->subled_info[i].intensity /
-					led_cdev->max_brightness;
+		mcled_cdev->subled_info[i].brightness =
+			DIV_ROUND_CLOSEST(brightness *
+					  mcled_cdev->subled_info[i].intensity,
+					  led_cdev->max_brightness);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/led-class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/led-class.c
@@ -28,11 +28,14 @@
 		struct device_attribute *attr, char *buf)
 {
 	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	unsigned int brightness;
 
-	/* no lock needed for this */
+	mutex_lock(&led_cdev->led_access);
 	led_update_brightness(led_cdev);
+	brightness = led_cdev->brightness;
+	mutex_unlock(&led_cdev->led_access);
 
-	return sprintf(buf, "%u\n", led_cdev->brightness);
+	return sprintf(buf, "%u\n", brightness);
 }
 
 static ssize_t brightness_store(struct device *dev,
@@ -69,8 +72,13 @@
 		struct device_attribute *attr, char *buf)
 {
 	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	unsigned int max_brightness;
+
+	mutex_lock(&led_cdev->led_access);
+	max_brightness = led_cdev->max_brightness;
+	mutex_unlock(&led_cdev->led_access);
 
-	return sprintf(buf, "%u\n", led_cdev->max_brightness);
+	return sprintf(buf, "%u\n", max_brightness);
 }
 static DEVICE_ATTR_RO(max_brightness);
 
@@ -241,8 +249,10 @@
 
 	led_cdev = dev_get_drvdata(led_dev);
 
-	if (!try_module_get(led_cdev->dev->parent->driver->owner))
+	if (!try_module_get(led_cdev->dev->parent->driver->owner)) {
+		put_device(led_cdev->dev);
 		return ERR_PTR(-ENODEV);
+	}
 
 	return led_cdev;
 }
@@ -255,6 +265,7 @@
 void led_put(struct led_classdev *led_cdev)
 {
 	module_put(led_cdev->dev->parent->driver->owner);
+	put_device(led_cdev->dev);
 }
 EXPORT_SYMBOL_GPL(led_put);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/led-triggers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/led-triggers.c
@@ -157,7 +157,6 @@
 /* Caller must ensure led_cdev->trigger_lock held */
 int led_trigger_set(struct led_classdev *led_cdev, struct led_trigger *trig)
 {
-	unsigned long flags;
 	char *event = NULL;
 	char *envp[2];
 	const char *name;
@@ -171,31 +170,47 @@
 
 	/* Remove any existing trigger */
 	if (led_cdev->trigger) {
-		write_lock_irqsave(&led_cdev->trigger->leddev_list_lock, flags);
-		list_del(&led_cdev->trig_list);
-		write_unlock_irqrestore(&led_cdev->trigger->leddev_list_lock,
-			flags);
+		spin_lock(&led_cdev->trigger->leddev_list_lock);
+		list_del_rcu(&led_cdev->trig_list);
+		spin_unlock(&led_cdev->trigger->leddev_list_lock);
+
+		/* ensure it's no longer visible on the led_cdevs list */
+		synchronize_rcu();
+
 		cancel_work_sync(&led_cdev->set_brightness_work);
 		led_stop_software_blink(led_cdev);
+		device_remove_groups(led_cdev->dev, led_cdev->trigger->groups);
 		if (led_cdev->trigger->deactivate)
 			led_cdev->trigger->deactivate(led_cdev);
-		device_remove_groups(led_cdev->dev, led_cdev->trigger->groups);
 		led_cdev->trigger = NULL;
 		led_cdev->trigger_data = NULL;
 		led_cdev->activated = false;
 		led_set_brightness(led_cdev, LED_OFF);
 	}
 	if (trig) {
-		write_lock_irqsave(&trig->leddev_list_lock, flags);
-		list_add_tail(&led_cdev->trig_list, &trig->led_cdevs);
-		write_unlock_irqrestore(&trig->leddev_list_lock, flags);
+		spin_lock(&trig->leddev_list_lock);
+		list_add_tail_rcu(&led_cdev->trig_list, &trig->led_cdevs);
+		spin_unlock(&trig->leddev_list_lock);
 		led_cdev->trigger = trig;
 
+		/*
+		 * Some activate() calls use led_trigger_event() to initialize
+		 * the brightness of the LED for which the trigger is being set.
+		 * Ensure the led_cdev is visible on trig->led_cdevs for this.
+		 */
+		synchronize_rcu();
+
+		/*
+		 * If "set brightness to 0" is pending in workqueue,
+		 * we don't want that to be reordered after ->activate()
+		 */
+		flush_work(&led_cdev->set_brightness_work);
+
+		ret = 0;
 		if (trig->activate)
 			ret = trig->activate(led_cdev);
 		else
-			ret = 0;
-
+			led_set_brightness(led_cdev, trig->brightness);
 		if (ret)
 			goto err_activate;
 
@@ -223,9 +238,10 @@
 		trig->deactivate(led_cdev);
 err_activate:
 
-	write_lock_irqsave(&led_cdev->trigger->leddev_list_lock, flags);
-	list_del(&led_cdev->trig_list);
-	write_unlock_irqrestore(&led_cdev->trigger->leddev_list_lock, flags);
+	spin_lock(&led_cdev->trigger->leddev_list_lock);
+	list_del_rcu(&led_cdev->trig_list);
+	spin_unlock(&led_cdev->trigger->leddev_list_lock);
+	synchronize_rcu();
 	led_cdev->trigger = NULL;
 	led_cdev->trigger_data = NULL;
 	led_set_brightness(led_cdev, LED_OFF);
@@ -265,19 +281,6 @@
 }
 EXPORT_SYMBOL_GPL(led_trigger_set_default);
 
-void led_trigger_rename_static(const char *name, struct led_trigger *trig)
-{
-	/* new name must be on a temporary string to prevent races */
-	BUG_ON(name == trig->name);
-
-	down_write(&triggers_list_lock);
-	/* this assumes that trig->name was originaly allocated to
-	 * non constant storage */
-	strcpy((char *)trig->name, name);
-	up_write(&triggers_list_lock);
-}
-EXPORT_SYMBOL_GPL(led_trigger_rename_static);
-
 /* LED Trigger Interface */
 
 int led_trigger_register(struct led_trigger *trig)
@@ -285,7 +288,7 @@
 	struct led_classdev *led_cdev;
 	struct led_trigger *_trig;
 
-	rwlock_init(&trig->leddev_list_lock);
+	spin_lock_init(&trig->leddev_list_lock);
 	INIT_LIST_HEAD(&trig->led_cdevs);
 
 	down_write(&triggers_list_lock);
@@ -378,15 +381,16 @@
 			enum led_brightness brightness)
 {
 	struct led_classdev *led_cdev;
-	unsigned long flags;
 
 	if (!trig)
 		return;
 
-	read_lock_irqsave(&trig->leddev_list_lock, flags);
-	list_for_each_entry(led_cdev, &trig->led_cdevs, trig_list)
+	trig->brightness = brightness;
+
+	rcu_read_lock();
+	list_for_each_entry_rcu(led_cdev, &trig->led_cdevs, trig_list)
 		led_set_brightness(led_cdev, brightness);
-	read_unlock_irqrestore(&trig->leddev_list_lock, flags);
+	rcu_read_unlock();
 }
 EXPORT_SYMBOL_GPL(led_trigger_event);
 
@@ -397,20 +401,19 @@
 			     int invert)
 {
 	struct led_classdev *led_cdev;
-	unsigned long flags;
 
 	if (!trig)
 		return;
 
-	read_lock_irqsave(&trig->leddev_list_lock, flags);
-	list_for_each_entry(led_cdev, &trig->led_cdevs, trig_list) {
+	rcu_read_lock();
+	list_for_each_entry_rcu(led_cdev, &trig->led_cdevs, trig_list) {
 		if (oneshot)
 			led_blink_set_oneshot(led_cdev, delay_on, delay_off,
 					      invert);
 		else
 			led_blink_set(led_cdev, delay_on, delay_off);
 	}
-	read_unlock_irqrestore(&trig->leddev_list_lock, flags);
+	rcu_read_unlock();
 }
 
 void led_trigger_blink(struct led_trigger *trig,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-aaeon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-aaeon.c
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * AAEON LED driver
+ *
+ * Copyright (c) 2021, AAEON Ltd.
+ *
+ * Author: Kunyang Fan <kunyang_fan@aaeon.com.tw>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/acpi.h>
+#include <linux/bitops.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/platform_data/x86/asus-wmi.h>
+#include <linux/platform_device.h>
+
+#define DRVNAME "led_aaeon"
+#define ASUS_NB_WMI_EVENT_GUID   "0B3CBB35-E3C2-45ED-91C2-4C5A6D195D1C"
+#define AAEON_WMI_MGMT_GUID      "97845ED0-4E6D-11DE-8A39-0800200C9A66"
+
+#define GET_LED_NUMBER_ID        0x00060000
+#define GET_LED_METHOD_ID        0x00060001
+#define SET_LED_METHOD_ID        0x00060002
+#define GET_LED_NUMBER_METHOD_ID 0x10
+
+
+struct aaeon_led_data {
+	int id;
+	struct led_classdev cdev;
+};
+
+static int aaeon_led_get_number(void)
+{
+	int err, retval;
+
+	err = asus_wmi_evaluate_method(GET_LED_NUMBER_ID,
+				       GET_LED_NUMBER_METHOD_ID,
+				       0, &retval);
+	if (err)
+		return err;
+
+	return retval;
+}
+
+static enum led_brightness aaeon_led_brightness_get(struct led_classdev
+						      *cdev)
+{
+	int err, brightness;
+	struct aaeon_led_data *led =
+			container_of(cdev, struct aaeon_led_data, cdev);
+	u32 arg0;
+
+	arg0 = (u32)(led->id & 0xF);
+	err = asus_wmi_evaluate_method(GET_LED_METHOD_ID, arg0, 0, &brightness);
+	if (err)
+		return err;
+
+	return brightness;
+};
+
+static void aaeon_led_brightness_set(struct led_classdev *cdev,
+				       enum led_brightness brightness)
+{
+	int err, retval;
+	struct aaeon_led_data *led =
+			container_of(cdev, struct aaeon_led_data, cdev);
+	u32 arg0;
+
+	arg0 = (u32)(led->id & 0xF);
+	if (brightness != LED_OFF)
+		arg0 |= BIT(16);
+
+	err = asus_wmi_evaluate_method(SET_LED_METHOD_ID, arg0, 0, &retval);
+};
+
+static int __init aaeon_add_led_device(struct platform_device *pdev,
+					   int id)
+{
+	struct aaeon_led_data *led;
+
+	led = devm_kzalloc(&pdev->dev, sizeof(struct aaeon_led_data), GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	led->id = id;
+	led->cdev.brightness_get = aaeon_led_brightness_get;
+	led->cdev.brightness_set = aaeon_led_brightness_set;
+	led->cdev.name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "led:%d:", id);
+
+	if (!led->cdev.name)
+		return -ENOMEM;
+
+	return devm_led_classdev_register(&pdev->dev, &led->cdev);
+}
+
+static int aaeon_led_probe(struct platform_device *pdev)
+{
+	int err = -ENODEV, i;
+	int led_number = 0;
+
+	pr_debug("aaeon led device probe!\n");
+	/* Prevent other drivers adding this platfom device */
+	if (!wmi_has_guid(AAEON_WMI_MGMT_GUID)) {
+		pr_debug("AAEON Management GUID not found\n");
+		return -ENODEV;
+	}
+
+	/* Query the number of led devices board support */
+	led_number = aaeon_led_get_number();
+
+	/*
+	 * If the number is 0 or can't get the number of leds,
+	 * no need to register any led device node.
+	 */
+	if (led_number <= 0)
+		return -ENODEV;
+
+	for (i = 0; i < led_number; i++) {
+		err = aaeon_add_led_device(pdev, i);
+		if (err)
+			break;
+	}
+
+	return err;
+}
+
+static struct platform_driver aaeon_led_driver = {
+	.driver = {
+		.name = "leds-aaeon",
+	},
+};
+
+module_platform_driver_probe(aaeon_led_driver, aaeon_led_probe);
+
+MODULE_ALIAS("platform:leds-aaeon");
+MODULE_DESCRIPTION("AAEON LED Driver");
+MODULE_AUTHOR("Kunyang Fan <kunyang_fan@asus.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-aw2013.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-aw2013.c
@@ -397,6 +397,7 @@
 	regulator_disable(chip->vcc_regulator);
 
 error:
+	mutex_unlock(&chip->mutex);
 	mutex_destroy(&chip->mutex);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-lp55xx-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-lp55xx-common.c
@@ -439,6 +439,8 @@
 		return -EINVAL;
 
 	if (pdata->enable_gpiod) {
+		gpiod_direction_output(pdata->enable_gpiod, 0);
+
 		gpiod_set_consumer_name(pdata->enable_gpiod, "LP55xx enable");
 		gpiod_set_value(pdata->enable_gpiod, 0);
 		usleep_range(1000, 2000); /* Keep enable down at least 1ms */
@@ -578,9 +580,6 @@
 	if (ret)
 		return ret;
 
-	if (*chan_nr < 0 || *chan_nr > cfg->max_channel)
-		return -EINVAL;
-
 	return 0;
 }
 
@@ -694,7 +693,7 @@
 	of_property_read_u8(np, "clock-mode", &pdata->clock_mode);
 
 	pdata->enable_gpiod = devm_gpiod_get_optional(dev, "enable",
-						      GPIOD_OUT_LOW);
+						      GPIOD_ASIS);
 	if (IS_ERR(pdata->enable_gpiod))
 		return ERR_CAST(pdata->enable_gpiod);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-lp8860.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-lp8860.c
@@ -267,7 +267,7 @@
 		goto out;
 	}
 
-	reg_count = ARRAY_SIZE(lp8860_eeprom_disp_regs) / sizeof(lp8860_eeprom_disp_regs[0]);
+	reg_count = ARRAY_SIZE(lp8860_eeprom_disp_regs);
 	for (i = 0; i < reg_count; i++) {
 		ret = regmap_write(led->eeprom_regmap,
 				lp8860_eeprom_disp_regs[i].reg,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-netxbig.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-netxbig.c
@@ -440,6 +440,7 @@
 	}
 	gpio_ext_pdev = of_find_device_by_node(gpio_ext_np);
 	if (!gpio_ext_pdev) {
+		of_node_put(gpio_ext_np);
 		dev_err(dev, "Failed to find platform device for gpio-ext\n");
 		return -ENODEV;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-pwm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-pwm.c
@@ -53,7 +53,7 @@
 		duty = led_dat->pwmstate.period - duty;
 
 	led_dat->pwmstate.duty_cycle = duty;
-	led_dat->pwmstate.enabled = duty > 0;
+	led_dat->pwmstate.enabled = true;
 	return pwm_apply_state(led_dat->pwm, &led_dat->pwmstate);
 }
 
@@ -146,7 +146,7 @@
 			led.name = to_of_node(fwnode)->name;
 
 		if (!led.name) {
-			ret = EINVAL;
+			ret = -EINVAL;
 			goto err_child_out;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-spi-byte.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-spi-byte.c
@@ -91,7 +91,6 @@
 		dev_err(dev, "Device must have exactly one LED sub-node.");
 		return -EINVAL;
 	}
-	child = of_get_next_available_child(dev_of_node(dev), NULL);
 
 	led = devm_kzalloc(dev, sizeof(*led), GFP_KERNEL);
 	if (!led)
@@ -107,11 +106,13 @@
 	led->ldev.max_brightness = led->cdef->max_value - led->cdef->off_value;
 	led->ldev.brightness_set_blocking = spi_byte_brightness_set_blocking;
 
+	child = of_get_next_available_child(dev_of_node(dev), NULL);
 	state = of_get_property(child, "default-state", NULL);
 	if (state) {
 		if (!strcmp(state, "on")) {
 			led->ldev.brightness = led->ldev.max_brightness;
 		} else if (strcmp(state, "off")) {
+			of_node_put(child);
 			/* all other cases except "off" */
 			dev_err(dev, "default-state can only be 'on' or 'off'");
 			return -EINVAL;
@@ -122,9 +123,12 @@
 
 	ret = devm_led_classdev_register(&spi->dev, &led->ldev);
 	if (ret) {
+		of_node_put(child);
 		mutex_destroy(&led->mutex);
 		return ret;
 	}
+
+	of_node_put(child);
 	spi_set_drvdata(spi, led);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-ss4200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-ss4200.c
@@ -356,8 +356,10 @@
 
 	nas_gpio_pci_dev = dev;
 	status = pci_read_config_dword(dev, PMBASE, &g_pm_io_base);
-	if (status)
+	if (status) {
+		status = pcibios_err_to_errno(status);
 		goto out;
+	}
 	g_pm_io_base &= 0x00000ff80;
 
 	status = pci_read_config_dword(dev, GPIO_CTRL, &gc);
@@ -369,8 +371,9 @@
 	}
 
 	status = pci_read_config_dword(dev, GPIO_BASE, &nas_gpio_io_base);
-	if (0 > status) {
+	if (status) {
 		dev_info(&dev->dev, "Unable to read GPIOBASE.\n");
+		status = pcibios_err_to_errno(status);
 		goto out;
 	}
 	dev_dbg(&dev->dev, ": GPIOBASE = 0x%08x\n", nas_gpio_io_base);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-tca6507.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-tca6507.c
@@ -696,8 +696,9 @@
 		if (fwnode_property_read_string(child, "label", &led.name))
 			led.name = fwnode_get_name(child);
 
-		fwnode_property_read_string(child, "linux,default-trigger",
-					    &led.default_trigger);
+		if (fwnode_property_read_string(child, "linux,default-trigger",
+						&led.default_trigger))
+			led.default_trigger = NULL;
 
 		led.flags = 0;
 		if (fwnode_property_match_string(child, "compatible",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/leds-turris-omnia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/leds-turris-omnia.c
@@ -2,7 +2,7 @@
 /*
  * CZ.NIC's Turris Omnia LEDs driver
  *
- * 2020 by Marek Behún <kabel@kernel.org>
+ * 2020, 2023 by Marek Behún <kabel@kernel.org>
  */
 
 #include <linux/i2c.h>
@@ -41,6 +41,37 @@
 	struct omnia_led leds[];
 };
 
+static int omnia_cmd_write_u8(const struct i2c_client *client, u8 cmd, u8 val)
+{
+	u8 buf[2] = { cmd, val };
+
+	return i2c_master_send(client, buf, sizeof(buf));
+}
+
+static int omnia_cmd_read_u8(const struct i2c_client *client, u8 cmd)
+{
+	struct i2c_msg msgs[2];
+	u8 reply;
+	int ret;
+
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = 1;
+	msgs[0].buf = &cmd;
+	msgs[1].addr = client->addr;
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].len = 1;
+	msgs[1].buf = &reply;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (likely(ret == ARRAY_SIZE(msgs)))
+		return reply;
+	else if (ret < 0)
+		return ret;
+	else
+		return -EIO;
+}
+
 static int omnia_led_brightness_set_blocking(struct led_classdev *cdev,
 					     enum led_brightness brightness)
 {
@@ -64,7 +95,7 @@
 	if (buf[2] || buf[3] || buf[4])
 		state |= CMD_LED_STATE_ON;
 
-	ret = i2c_smbus_write_byte_data(leds->client, CMD_LED_STATE, state);
+	ret = omnia_cmd_write_u8(leds->client, CMD_LED_STATE, state);
 	if (ret >= 0 && (state & CMD_LED_STATE_ON))
 		ret = i2c_master_send(leds->client, buf, 5);
 
@@ -114,9 +145,9 @@
 	cdev->brightness_set_blocking = omnia_led_brightness_set_blocking;
 
 	/* put the LED into software mode */
-	ret = i2c_smbus_write_byte_data(client, CMD_LED_MODE,
-					CMD_LED_MODE_LED(led->reg) |
-					CMD_LED_MODE_USER);
+	ret = omnia_cmd_write_u8(client, CMD_LED_MODE,
+				 CMD_LED_MODE_LED(led->reg) |
+				 CMD_LED_MODE_USER);
 	if (ret < 0) {
 		dev_err(dev, "Cannot set LED %pOF to software mode: %i\n", np,
 			ret);
@@ -124,8 +155,8 @@
 	}
 
 	/* disable the LED */
-	ret = i2c_smbus_write_byte_data(client, CMD_LED_STATE,
-					CMD_LED_STATE_LED(led->reg));
+	ret = omnia_cmd_write_u8(client, CMD_LED_STATE,
+				 CMD_LED_STATE_LED(led->reg));
 	if (ret < 0) {
 		dev_err(dev, "Cannot set LED %pOF brightness: %i\n", np, ret);
 		return ret;
@@ -156,12 +187,9 @@
 			       char *buf)
 {
 	struct i2c_client *client = to_i2c_client(dev);
-	struct omnia_leds *leds = i2c_get_clientdata(client);
 	int ret;
 
-	mutex_lock(&leds->lock);
-	ret = i2c_smbus_read_byte_data(client, CMD_LED_GET_BRIGHTNESS);
-	mutex_unlock(&leds->lock);
+	ret = omnia_cmd_read_u8(client, CMD_LED_GET_BRIGHTNESS);
 
 	if (ret < 0)
 		return ret;
@@ -173,7 +201,6 @@
 				const char *buf, size_t count)
 {
 	struct i2c_client *client = to_i2c_client(dev);
-	struct omnia_leds *leds = i2c_get_clientdata(client);
 	unsigned long brightness;
 	int ret;
 
@@ -183,15 +210,9 @@
 	if (brightness > 100)
 		return -EINVAL;
 
-	mutex_lock(&leds->lock);
-	ret = i2c_smbus_write_byte_data(client, CMD_LED_SET_BRIGHTNESS,
-					(u8)brightness);
-	mutex_unlock(&leds->lock);
-
-	if (ret < 0)
-		return ret;
+	ret = omnia_cmd_write_u8(client, CMD_LED_SET_BRIGHTNESS, brightness);
 
-	return count;
+	return ret < 0 ? ret : count;
 }
 static DEVICE_ATTR_RW(brightness);
 
@@ -250,8 +271,8 @@
 	u8 buf[5];
 
 	/* put all LEDs into default (HW triggered) mode */
-	i2c_smbus_write_byte_data(client, CMD_LED_MODE,
-				  CMD_LED_MODE_LED(OMNIA_BOARD_LEDS));
+	omnia_cmd_write_u8(client, CMD_LED_MODE,
+			   CMD_LED_MODE_LED(OMNIA_BOARD_LEDS));
 
 	/* set all LEDs color to [255, 255, 255] */
 	buf[0] = CMD_LED_COLOR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/trigger/ledtrig-cpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/trigger/ledtrig-cpu.c
@@ -130,7 +130,7 @@
 
 static int __init ledtrig_cpu_init(void)
 {
-	int cpu;
+	unsigned int cpu;
 	int ret;
 
 	/* Supports up to 9999 cpu cores */
@@ -152,7 +152,7 @@
 		if (cpu >= 8)
 			continue;
 
-		snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
+		snprintf(trig->name, MAX_NAME_LEN, "cpu%u", cpu);
 
 		led_trigger_register_simple(trig->name, &trig->_trig);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/trigger/ledtrig-netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/trigger/ledtrig-netdev.c
@@ -318,6 +318,9 @@
 	clear_bit(NETDEV_LED_MODE_LINKUP, &trigger_data->mode);
 	switch (evt) {
 	case NETDEV_CHANGENAME:
+		if (netif_carrier_ok(dev))
+			set_bit(NETDEV_LED_MODE_LINKUP, &trigger_data->mode);
+		fallthrough;
 	case NETDEV_REGISTER:
 		if (trigger_data->net_dev)
 			dev_put(trigger_data->net_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/trigger/ledtrig-panic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/trigger/ledtrig-panic.c
@@ -64,10 +64,13 @@
 
 static int __init ledtrig_panic_init(void)
 {
+	led_trigger_register_simple("panic", &trigger);
+	if (!trigger)
+		return -ENOMEM;
+
 	atomic_notifier_chain_register(&panic_notifier_list,
 				       &led_trigger_panic_nb);
 
-	led_trigger_register_simple("panic", &trigger);
 	panic_blink = led_panic_blink;
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/trigger/ledtrig-timer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/trigger/ledtrig-timer.c
@@ -110,11 +110,6 @@
 		led_cdev->flags &= ~LED_INIT_DEFAULT_TRIGGER;
 	}
 
-	/*
-	 * If "set brightness to 0" is pending in workqueue, we don't
-	 * want that to be reordered after blink_set()
-	 */
-	flush_work(&led_cdev->set_brightness_work);
 	led_blink_set(led_cdev, &led_cdev->blink_delay_on,
 		      &led_cdev->blink_delay_off);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/leds/trigger/ledtrig-tty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/leds/trigger/ledtrig-tty.c
@@ -7,6 +7,8 @@
 #include <linux/tty.h>
 #include <uapi/linux/serial.h>
 
+#define LEDTRIG_TTY_INTERVAL	50
+
 struct ledtrig_tty_data {
 	struct led_classdev *led_cdev;
 	struct delayed_work dwork;
@@ -122,17 +124,19 @@
 
 	if (icount.rx != trigger_data->rx ||
 	    icount.tx != trigger_data->tx) {
-		led_set_brightness_sync(trigger_data->led_cdev, LED_ON);
+		unsigned long interval = LEDTRIG_TTY_INTERVAL;
+
+		led_blink_set_oneshot(trigger_data->led_cdev, &interval,
+				      &interval, 0);
 
 		trigger_data->rx = icount.rx;
 		trigger_data->tx = icount.tx;
-	} else {
-		led_set_brightness_sync(trigger_data->led_cdev, LED_OFF);
 	}
 
 out:
 	mutex_unlock(&trigger_data->mutex);
-	schedule_delayed_work(&trigger_data->dwork, msecs_to_jiffies(100));
+	schedule_delayed_work(&trigger_data->dwork,
+			      msecs_to_jiffies(LEDTRIG_TTY_INTERVAL * 2));
 }
 
 static struct attribute *ledtrig_tty_attrs[] = {
@@ -164,6 +168,10 @@
 
 	cancel_delayed_work_sync(&trigger_data->dwork);
 
+	kfree(trigger_data->ttyname);
+	tty_kref_put(trigger_data->tty);
+	trigger_data->tty = NULL;
+
 	kfree(trigger_data);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/Kconfig
@@ -44,6 +44,7 @@
 config ADB_CUDA
 	bool "Support for Cuda/Egret based Macs and PowerMacs"
 	depends on (ADB || PPC_PMAC) && !PPC_PMAC64
+	select RTC_LIB
 	help
 	  This provides support for Cuda/Egret based Macintosh and
 	  Power Macintosh systems. This includes most m68k based Macs,
@@ -57,6 +58,7 @@
 config ADB_PMU
 	bool "Support for PMU based PowerMacs and PowerBooks"
 	depends on PPC_PMAC || MAC
+	select RTC_LIB
 	help
 	  On PowerBooks, iBooks, and recent iMacs and Power Macintoshes, the
 	  PMU is an embedded microprocessor whose primary function is to
@@ -67,6 +69,10 @@
 	  this device; you should do so if your machine is one of those
 	  mentioned above.
 
+config ADB_PMU_EVENT
+	def_bool y
+	depends on ADB_PMU && INPUT=y
+
 config ADB_PMU_LED
 	bool "Support for the Power/iBook front LED"
 	depends on PPC_PMAC && ADB_PMU
@@ -80,6 +86,7 @@
 
 config ADB_PMU_LED_DISK
 	bool "Use front LED as DISK LED by default"
+	depends on ATA
 	depends on ADB_PMU_LED
 	depends on LEDS_CLASS
 	select LEDS_TRIGGERS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/Makefile
@@ -12,7 +12,8 @@
 obj-$(CONFIG_INPUT_ADBHID)	+= adbhid.o
 obj-$(CONFIG_ANSLCD)		+= ans-lcd.o
 
-obj-$(CONFIG_ADB_PMU)		+= via-pmu.o via-pmu-event.o
+obj-$(CONFIG_ADB_PMU)		+= via-pmu.o
+obj-$(CONFIG_ADB_PMU_EVENT)	+= via-pmu-event.o
 obj-$(CONFIG_ADB_PMU_LED)	+= via-pmu-led.o
 obj-$(CONFIG_PMAC_BACKLIGHT)	+= via-pmu-backlight.o
 obj-$(CONFIG_ADB_CUDA)		+= via-cuda.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/adb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/adb.c
@@ -647,7 +647,7 @@
 
 	switch(req->data[1]) {
 	case ADB_QUERY_GETDEVINFO:
-		if (req->nbytes < 3)
+		if (req->nbytes < 3 || req->data[2] >= 16)
 			break;
 		mutex_lock(&adb_handler_mutex);
 		req->reply[0] = adb_handler[req->data[2]].original_address;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/macio-adb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/macio-adb.c
@@ -105,6 +105,10 @@
 		return -ENXIO;
 	}
 	adb = ioremap(r.start, sizeof(struct adb_regs));
+	if (!adb) {
+		of_node_put(adbs);
+		return -ENOMEM;
+	}
 
 	out_8(&adb->ctrl.r, 0);
 	out_8(&adb->intr.r, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/macio_asic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/macio_asic.c
@@ -423,7 +423,7 @@
 	if (of_device_register(&dev->ofdev) != 0) {
 		printk(KERN_DEBUG"macio: device registration error for %s!\n",
 		       dev_name(&dev->ofdev.dev));
-		kfree(dev);
+		put_device(&dev->ofdev.dev);
 		return NULL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/therm_windtunnel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/therm_windtunnel.c
@@ -549,7 +549,7 @@
 	platform_driver_unregister( &therm_of_driver );
 
 	if( x.of_dev )
-		of_device_unregister( x.of_dev );
+		of_platform_device_destroy(&x.of_dev->dev, NULL);
 }
 
 module_init(g4fan_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/via-macii.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/via-macii.c
@@ -140,24 +140,19 @@
 /* Initialize the driver */
 static int macii_init(void)
 {
-	unsigned long flags;
 	int err;
 
-	local_irq_save(flags);
-
 	err = macii_init_via();
 	if (err)
-		goto out;
+		return err;
 
 	err = request_irq(IRQ_MAC_ADB, macii_interrupt, 0, "ADB",
 			  macii_interrupt);
 	if (err)
-		goto out;
+		return err;
 
 	macii_state = idle;
-out:
-	local_irq_restore(flags);
-	return err;
+	return 0;
 }
 
 /* initialize the hardware */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/via-pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/via-pmu.c
@@ -1459,7 +1459,7 @@
 		pmu_pass_intr(data, len);
 		/* len == 6 is probably a bad check. But how do I
 		 * know what PMU versions send what events here? */
-		if (len == 6) {
+		if (IS_ENABLED(CONFIG_ADB_PMU_EVENT) && len == 6) {
 			via_pmu_event(PMU_EVT_POWER, !!(data[1]&8));
 			via_pmu_event(PMU_EVT_LID, data[1]&1);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/windfarm_lm75_sensor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/windfarm_lm75_sensor.c
@@ -34,8 +34,8 @@
 #endif
 
 struct wf_lm75_sensor {
-	int			ds1775 : 1;
-	int			inited : 1;
+	unsigned int		ds1775 : 1;
+	unsigned int		inited : 1;
 	struct i2c_client	*i2c;
 	struct wf_sensor	sens;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/windfarm_smu_sat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/windfarm_smu_sat.c
@@ -171,6 +171,7 @@
 
 	if (sat->nr >= 0)
 		sats[sat->nr] = NULL;
+	of_node_put(sat->node);
 	kfree(sat);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/macintosh/windfarm_smu_sensors.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/macintosh/windfarm_smu_sensors.c
@@ -273,8 +273,8 @@
 	struct list_head	link;
 	struct wf_sensor	*volts;
 	struct wf_sensor	*amps;
-	int			fake_volts : 1;
-	int			quadratic : 1;
+	unsigned int		fake_volts : 1;
+	unsigned int		quadratic : 1;
 	struct wf_sensor	sens;
 };
 #define to_smu_cpu_power(c) container_of(c, struct smu_cpu_power_sensor, sens)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/arm_mhuv2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/arm_mhuv2.c
@@ -499,7 +499,7 @@
 static struct mbox_chan *get_irq_chan_comb(struct mhuv2 *mhu, u32 __iomem *reg)
 {
 	struct mbox_chan *chans = mhu->mbox.chans;
-	int channel = 0, i, offset = 0, windows, protocol, ch_wn;
+	int channel = 0, i, j, offset = 0, windows, protocol, ch_wn;
 	u32 stat;
 
 	for (i = 0; i < MHUV2_CMB_INT_ST_REG_CNT; i++) {
@@ -509,9 +509,9 @@
 
 		ch_wn = i * MHUV2_STAT_BITS + __builtin_ctz(stat);
 
-		for (i = 0; i < mhu->length; i += 2) {
-			protocol = mhu->protocols[i];
-			windows = mhu->protocols[i + 1];
+		for (j = 0; j < mhu->length; j += 2) {
+			protocol = mhu->protocols[j];
+			windows = mhu->protocols[j + 1];
 
 			if (ch_wn >= offset + windows) {
 				if (protocol == DOORBELL)
@@ -552,7 +552,8 @@
 	priv = chan->con_priv;
 
 	if (!IS_PROTOCOL_DOORBELL(priv)) {
-		writel_relaxed(1, &mhu->send->ch_wn[priv->ch_wn_idx + priv->windows - 1].int_clr);
+		for (i = 0; i < priv->windows; i++)
+			writel_relaxed(1, &mhu->send->ch_wn[priv->ch_wn_idx + i].int_clr);
 
 		if (chan->cl) {
 			mbox_chan_txdone(chan, 0);
@@ -1061,8 +1062,8 @@
 	int ret = -EINVAL;
 
 	reg = devm_of_iomap(dev, dev->of_node, 0, NULL);
-	if (!reg)
-		return -ENOMEM;
+	if (IS_ERR(reg))
+		return PTR_ERR(reg);
 
 	mhu = devm_kzalloc(dev, sizeof(*mhu), GFP_KERNEL);
 	if (!mhu)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/bcm-flexrm-mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/bcm-flexrm-mailbox.c
@@ -632,15 +632,15 @@
 
 	rc = dma_map_sg(dev, msg->spu.src, sg_nents(msg->spu.src),
 			DMA_TO_DEVICE);
-	if (rc < 0)
-		return rc;
+	if (!rc)
+		return -EIO;
 
 	rc = dma_map_sg(dev, msg->spu.dst, sg_nents(msg->spu.dst),
 			DMA_FROM_DEVICE);
-	if (rc < 0) {
+	if (!rc) {
 		dma_unmap_sg(dev, msg->spu.src, sg_nents(msg->spu.src),
 			     DMA_TO_DEVICE);
-		return rc;
+		return -EIO;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/bcm2835-mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/bcm2835-mailbox.c
@@ -146,7 +146,8 @@
 	spin_lock_init(&mbox->lock);
 
 	ret = devm_request_irq(dev, irq_of_parse_and_map(dev->of_node, 0),
-			       bcm2835_mbox_irq, 0, dev_name(dev), mbox);
+			       bcm2835_mbox_irq, IRQF_NO_SUSPEND, dev_name(dev),
+			       mbox);
 	if (ret) {
 		dev_err(dev, "Failed to register a mailbox IRQ handler: %d\n",
 			ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/imx-mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/imx-mailbox.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/suspend.h>
 #include <linux/slab.h>
 
 #define IMX_MU_CHANS		16
@@ -67,6 +68,7 @@
 	const struct imx_mu_dcfg	*dcfg;
 	struct clk		*clk;
 	int			irq;
+	bool			suspend;
 
 	u32 xcr[4];
 
@@ -307,6 +309,9 @@
 		return IRQ_NONE;
 	}
 
+	if (priv->suspend)
+		pm_system_wakeup();
+
 	return IRQ_HANDLED;
 }
 
@@ -652,6 +657,8 @@
 			priv->xcr[i] = imx_mu_read(priv, priv->dcfg->xCR[i]);
 	}
 
+	priv->suspend = true;
+
 	return 0;
 }
 
@@ -668,11 +675,13 @@
 	 * send failed, may lead to system freeze. This issue
 	 * is observed by testing freeze mode suspend.
 	 */
-	if (!imx_mu_read(priv, priv->dcfg->xCR[0]) && !priv->clk) {
+	if (!priv->clk && !imx_mu_read(priv, priv->dcfg->xCR[0])) {
 		for (i = 0; i < IMX_MU_xCR_MAX; i++)
 			imx_mu_write(priv, priv->xcr[i], priv->dcfg->xCR[i]);
 	}
 
+	priv->suspend = false;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/mailbox-mpfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/mailbox-mpfs.c
@@ -2,7 +2,7 @@
 /*
  * Microchip PolarFire SoC (MPFS) system controller/mailbox controller driver
  *
- * Copyright (c) 2020 Microchip Corporation. All rights reserved.
+ * Copyright (c) 2020-2022 Microchip Corporation. All rights reserved.
  *
  * Author: Conor Dooley <conor.dooley@microchip.com>
  *
@@ -56,12 +56,13 @@
 #define SCB_STATUS_NOTIFY_MASK BIT(SCB_STATUS_NOTIFY)
 
 #define SCB_STATUS_POS (16)
-#define SCB_STATUS_MASK GENMASK_ULL(SCB_STATUS_POS + SCB_MASK_WIDTH, SCB_STATUS_POS)
+#define SCB_STATUS_MASK GENMASK(SCB_STATUS_POS + SCB_MASK_WIDTH - 1, SCB_STATUS_POS)
 
 struct mpfs_mbox {
 	struct mbox_controller controller;
 	struct device *dev;
 	int irq;
+	void __iomem *ctrl_base;
 	void __iomem *mbox_base;
 	void __iomem *int_reg;
 	struct mbox_chan chans[1];
@@ -73,11 +74,18 @@
 {
 	u32 status;
 
-	status = readl_relaxed(mbox->mbox_base + SERVICES_SR_OFFSET);
+	status = readl_relaxed(mbox->ctrl_base + SERVICES_SR_OFFSET);
 
 	return status & SCB_STATUS_BUSY_MASK;
 }
 
+static bool mpfs_mbox_last_tx_done(struct mbox_chan *chan)
+{
+	struct mpfs_mbox *mbox = (struct mpfs_mbox *)chan->con_priv;
+
+	return !mpfs_mbox_busy(mbox);
+}
+
 static int mpfs_mbox_send_data(struct mbox_chan *chan, void *data)
 {
 	struct mpfs_mbox *mbox = (struct mpfs_mbox *)chan->con_priv;
@@ -99,29 +107,27 @@
 
 		for (index = 0; index < (msg->cmd_data_size / 4); index++)
 			writel_relaxed(word_buf[index],
-				       mbox->mbox_base + MAILBOX_REG_OFFSET + index * 0x4);
+				       mbox->mbox_base + msg->mbox_offset + index * 0x4);
 		if (extra_bits) {
 			u8 i;
 			u8 byte_off = ALIGN_DOWN(msg->cmd_data_size, 4);
 			u8 *byte_buf = msg->cmd_data + byte_off;
 
-			val = readl_relaxed(mbox->mbox_base +
-					    MAILBOX_REG_OFFSET + index * 0x4);
+			val = readl_relaxed(mbox->mbox_base + msg->mbox_offset + index * 0x4);
 
 			for (i = 0u; i < extra_bits; i++) {
 				val &= ~(0xffu << (i * 8u));
 				val |= (byte_buf[i] << (i * 8u));
 			}
 
-			writel_relaxed(val,
-				       mbox->mbox_base + MAILBOX_REG_OFFSET + index * 0x4);
+			writel_relaxed(val, mbox->mbox_base + msg->mbox_offset + index * 0x4);
 		}
 	}
 
 	opt_sel = ((msg->mbox_offset << 7u) | (msg->cmd_opcode & 0x7fu));
 	tx_trigger = (opt_sel << SCB_CTRL_POS) & SCB_CTRL_MASK;
 	tx_trigger |= SCB_CTRL_REQ_MASK | SCB_STATUS_NOTIFY_MASK;
-	writel_relaxed(tx_trigger, mbox->mbox_base + SERVICES_CR_OFFSET);
+	writel_relaxed(tx_trigger, mbox->ctrl_base + SERVICES_CR_OFFSET);
 
 	return 0;
 }
@@ -131,17 +137,42 @@
 	struct mpfs_mbox *mbox = (struct mpfs_mbox *)chan->con_priv;
 	struct mpfs_mss_response *response = mbox->response;
 	u16 num_words = ALIGN((response->resp_size), (4)) / 4U;
-	u32 i;
+	u32 i, status;
 
 	if (!response->resp_msg) {
 		dev_err(mbox->dev, "failed to assign memory for response %d\n", -ENOMEM);
 		return;
 	}
 
+	/*
+	 * The status is stored in bits 31:16 of the SERVICES_SR register.
+	 * It is only valid when BUSY == 0.
+	 * We should *never* get an interrupt while the controller is
+	 * still in the busy state. If we do, something has gone badly
+	 * wrong & the content of the mailbox would not be valid.
+	 */
+	if (mpfs_mbox_busy(mbox)) {
+		dev_err(mbox->dev, "got an interrupt but system controller is busy\n");
+		response->resp_status = 0xDEAD;
+		return;
+	}
+
+	status = readl_relaxed(mbox->ctrl_base + SERVICES_SR_OFFSET);
+
+	/*
+	 * If the status of the individual servers is non-zero, the service has
+	 * failed. The contents of the mailbox at this point are not be valid,
+	 * so don't bother reading them. Set the status so that the driver
+	 * implementing the service can handle the result.
+	 */
+	response->resp_status = (status & SCB_STATUS_MASK) >> SCB_STATUS_POS;
+	if (response->resp_status)
+		return;
+
 	if (!mpfs_mbox_busy(mbox)) {
 		for (i = 0; i < num_words; i++) {
 			response->resp_msg[i] =
-				readl_relaxed(mbox->mbox_base + MAILBOX_REG_OFFSET
+				readl_relaxed(mbox->mbox_base
 					      + mbox->resp_offset + i * 0x4);
 		}
 	}
@@ -158,7 +189,6 @@
 
 	mpfs_mbox_rx_data(chan);
 
-	mbox_chan_txdone(chan, 0);
 	return IRQ_HANDLED;
 }
 
@@ -188,6 +218,7 @@
 	.send_data = mpfs_mbox_send_data,
 	.startup = mpfs_mbox_startup,
 	.shutdown = mpfs_mbox_shutdown,
+	.last_tx_done = mpfs_mbox_last_tx_done,
 };
 
 static int mpfs_mbox_probe(struct platform_device *pdev)
@@ -200,14 +231,18 @@
 	if (!mbox)
 		return -ENOMEM;
 
-	mbox->mbox_base = devm_platform_get_and_ioremap_resource(pdev, 0, &regs);
-	if (IS_ERR(mbox->mbox_base))
-		return PTR_ERR(mbox->mbox_base);
+	mbox->ctrl_base = devm_platform_get_and_ioremap_resource(pdev, 0, &regs);
+	if (IS_ERR(mbox->ctrl_base))
+		return PTR_ERR(mbox->ctrl_base);
 
 	mbox->int_reg = devm_platform_get_and_ioremap_resource(pdev, 1, &regs);
 	if (IS_ERR(mbox->int_reg))
 		return PTR_ERR(mbox->int_reg);
 
+	mbox->mbox_base = devm_platform_get_and_ioremap_resource(pdev, 2, &regs);
+	if (IS_ERR(mbox->mbox_base)) // account for the old dt-binding w/ 2 regs
+		mbox->mbox_base = mbox->ctrl_base + MAILBOX_REG_OFFSET;
+
 	mbox->irq = platform_get_irq(pdev, 0);
 	if (mbox->irq < 0)
 		return mbox->irq;
@@ -219,7 +254,8 @@
 	mbox->controller.num_chans = 1;
 	mbox->controller.chans = mbox->chans;
 	mbox->controller.ops = &mpfs_mbox_ops;
-	mbox->controller.txdone_irq = true;
+	mbox->controller.txdone_poll = true;
+	mbox->controller.txpoll_period = 10u;
 
 	ret = devm_mbox_controller_register(&pdev->dev, &mbox->controller);
 	if (ret) {
@@ -232,7 +268,7 @@
 }
 
 static const struct of_device_id mpfs_mbox_of_match[] = {
-	{.compatible = "microchip,polarfire-soc-mailbox", },
+	{.compatible = "microchip,mpfs-mailbox", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, mpfs_mbox_of_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/mailbox-test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/mailbox-test.c
@@ -12,6 +12,7 @@
 #include <linux/kernel.h>
 #include <linux/mailbox_client.h>
 #include <linux/module.h>
+#include <linux/mutex.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/poll.h>
@@ -38,6 +39,7 @@
 	char			*signal;
 	char			*message;
 	spinlock_t		lock;
+	struct mutex		mutex;
 	wait_queue_head_t	waitq;
 	struct fasync_struct	*async_queue;
 	struct dentry		*root_debugfs_dir;
@@ -95,6 +97,7 @@
 				       size_t count, loff_t *ppos)
 {
 	struct mbox_test_device *tdev = filp->private_data;
+	char *message;
 	void *data;
 	int ret;
 
@@ -110,10 +113,13 @@
 		return -EINVAL;
 	}
 
-	tdev->message = kzalloc(MBOX_MAX_MSG_LEN, GFP_KERNEL);
-	if (!tdev->message)
+	message = kzalloc(MBOX_MAX_MSG_LEN, GFP_KERNEL);
+	if (!message)
 		return -ENOMEM;
 
+	mutex_lock(&tdev->mutex);
+
+	tdev->message = message;
 	ret = copy_from_user(tdev->message, userbuf, count);
 	if (ret) {
 		ret = -EFAULT;
@@ -144,6 +150,8 @@
 	kfree(tdev->message);
 	tdev->signal = NULL;
 
+	mutex_unlock(&tdev->mutex);
+
 	return ret < 0 ? ret : count;
 }
 
@@ -392,6 +400,7 @@
 	platform_set_drvdata(pdev, tdev);
 
 	spin_lock_init(&tdev->lock);
+	mutex_init(&tdev->mutex);
 
 	if (tdev->rx_channel) {
 		tdev->rx_buffer = devm_kzalloc(&pdev->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/mailbox.c
@@ -82,11 +82,11 @@
 exit:
 	spin_unlock_irqrestore(&chan->lock, flags);
 
-	/* kick start the timer immediately to avoid delays */
 	if (!err && (chan->txdone_method & TXDONE_BY_POLL)) {
-		/* but only if not already active */
-		if (!hrtimer_active(&chan->mbox->poll_hrt))
-			hrtimer_start(&chan->mbox->poll_hrt, 0, HRTIMER_MODE_REL);
+		/* kick start the timer immediately to avoid delays */
+		spin_lock_irqsave(&chan->mbox->poll_hrt_lock, flags);
+		hrtimer_start(&chan->mbox->poll_hrt, 0, HRTIMER_MODE_REL);
+		spin_unlock_irqrestore(&chan->mbox->poll_hrt_lock, flags);
 	}
 }
 
@@ -120,20 +120,26 @@
 		container_of(hrtimer, struct mbox_controller, poll_hrt);
 	bool txdone, resched = false;
 	int i;
+	unsigned long flags;
 
 	for (i = 0; i < mbox->num_chans; i++) {
 		struct mbox_chan *chan = &mbox->chans[i];
 
 		if (chan->active_req && chan->cl) {
-			resched = true;
 			txdone = chan->mbox->ops->last_tx_done(chan);
 			if (txdone)
 				tx_tick(chan, 0);
+			else
+				resched = true;
 		}
 	}
 
 	if (resched) {
-		hrtimer_forward_now(hrtimer, ms_to_ktime(mbox->txpoll_period));
+		spin_lock_irqsave(&mbox->poll_hrt_lock, flags);
+		if (!hrtimer_is_queued(hrtimer))
+			hrtimer_forward_now(hrtimer, ms_to_ktime(mbox->txpoll_period));
+		spin_unlock_irqrestore(&mbox->poll_hrt_lock, flags);
+
 		return HRTIMER_RESTART;
 	}
 	return HRTIMER_NORESTART;
@@ -500,6 +506,7 @@
 		hrtimer_init(&mbox->poll_hrt, CLOCK_MONOTONIC,
 			     HRTIMER_MODE_REL);
 		mbox->poll_hrt.function = txdone_hrtimer;
+		spin_lock_init(&mbox->poll_hrt_lock);
 	}
 
 	for (i = 0; i < mbox->num_chans; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/mtk-cmdq-mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/mtk-cmdq-mailbox.c
@@ -195,7 +195,6 @@
 	struct cmdq_task_cb *cb = &task->pkt->async_cb;
 	struct cmdq_cb_data data;
 
-	WARN_ON(cb->cb == (cmdq_async_flush_cb)NULL);
 	data.sta = sta;
 	data.data = cb->data;
 	data.pkt = task->pkt;
@@ -532,7 +531,8 @@
 	struct device_node *phandle = dev->of_node;
 	struct device_node *node;
 	int alias_id = 0;
-	char clk_name[4] = "gce";
+	static const char * const clk_name = "gce";
+	static const char * const clk_names[] = { "gce0", "gce1" };
 
 	cmdq = devm_kzalloc(dev, sizeof(*cmdq), GFP_KERNEL);
 	if (!cmdq)
@@ -570,12 +570,9 @@
 
 	if (cmdq->gce_num > 1) {
 		for_each_child_of_node(phandle->parent, node) {
-			char clk_id[8];
-
 			alias_id = of_alias_get_id(node, clk_name);
-			if (alias_id < cmdq->gce_num) {
-				snprintf(clk_id, sizeof(clk_id), "%s%d", clk_name, alias_id);
-				cmdq->clocks[alias_id].id = clk_id;
+			if (alias_id >= 0 && alias_id < cmdq->gce_num) {
+				cmdq->clocks[alias_id].id = clk_names[alias_id];
 				cmdq->clocks[alias_id].clk = of_clk_get(node, 0);
 				if (IS_ERR(cmdq->clocks[alias_id].clk)) {
 					dev_err(dev, "failed to get gce clk: %d\n", alias_id);
@@ -663,7 +660,7 @@
 	.thread_nr = 24,
 	.shift = 3,
 	.control_by_sw = true,
-	.gce_num = 2
+	.gce_num = 1
 };
 
 static const struct gce_plat gce_plat_v6 = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/rockchip-mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/rockchip-mailbox.c
@@ -159,7 +159,7 @@
 	{ .compatible = "rockchip,rk3368-mailbox", .data = &rk3368_drv_data},
 	{ },
 };
-MODULE_DEVICE_TABLE(of, rockchp_mbox_of_match);
+MODULE_DEVICE_TABLE(of, rockchip_mbox_of_match);
 
 static int rockchip_mbox_probe(struct platform_device *pdev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/tegra-hsp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/tegra-hsp.c
@@ -412,6 +412,11 @@
 		value = tegra_hsp_channel_readl(ch, HSP_SM_SHRD_MBOX);
 		if ((value & HSP_SM_SHRD_MBOX_FULL) == 0) {
 			mbox_chan_txdone(chan, 0);
+
+			/* Wait until channel is empty */
+			if (chan->active_req != NULL)
+				continue;
+
 			return 0;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/ti-msgmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/ti-msgmgr.c
@@ -385,14 +385,20 @@
 		/* Ensure all unused data is 0 */
 		data_trail &= 0xFFFFFFFF >> (8 * (sizeof(u32) - trail_bytes));
 		writel(data_trail, data_reg);
-		data_reg++;
+		data_reg += sizeof(u32);
 	}
+
 	/*
 	 * 'data_reg' indicates next register to write. If we did not already
 	 * write on tx complete reg(last reg), we must do so for transmit
+	 * In addition, we also need to make sure all intermediate data
+	 * registers(if any required), are reset to 0 for TISCI backward
+	 * compatibility to be maintained.
 	 */
-	if (data_reg <= qinst->queue_buff_end)
-		writel(0, qinst->queue_buff_end);
+	while (data_reg <= qinst->queue_buff_end) {
+		writel(0, data_reg);
+		data_reg += sizeof(u32);
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mailbox/zynqmp-ipi-mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mailbox/zynqmp-ipi-mailbox.c
@@ -110,7 +110,7 @@
 	unsigned int method;
 	u32 local_id;
 	int num_mboxes;
-	struct zynqmp_ipi_mbox *ipi_mboxes;
+	struct zynqmp_ipi_mbox ipi_mboxes[];
 };
 
 static struct device_driver zynqmp_ipi_mbox_driver = {
@@ -152,7 +152,7 @@
 	struct zynqmp_ipi_message *msg;
 	u64 arg0, arg3;
 	struct arm_smccc_res res;
-	int ret, i;
+	int ret, i, status = IRQ_NONE;
 
 	(void)irq;
 	arg0 = SMC_IPI_MAILBOX_STATUS_ENQUIRY;
@@ -170,11 +170,11 @@
 				memcpy_fromio(msg->data, mchan->req_buf,
 					      msg->len);
 				mbox_chan_received_data(chan, (void *)msg);
-				return IRQ_HANDLED;
+				status = IRQ_HANDLED;
 			}
 		}
 	}
-	return IRQ_NONE;
+	return status;
 }
 
 /**
@@ -493,6 +493,7 @@
 	ret = device_register(&ipi_mbox->dev);
 	if (ret) {
 		dev_err(dev, "Failed to register ipi mbox dev.\n");
+		put_device(&ipi_mbox->dev);
 		return ret;
 	}
 	mdev = &ipi_mbox->dev;
@@ -619,7 +620,8 @@
 		ipi_mbox = &pdata->ipi_mboxes[i];
 		if (ipi_mbox->dev.parent) {
 			mbox_controller_unregister(&ipi_mbox->mbox);
-			device_unregister(&ipi_mbox->dev);
+			if (device_is_registered(&ipi_mbox->dev))
+				device_unregister(&ipi_mbox->dev);
 		}
 	}
 }
@@ -632,8 +634,13 @@
 	struct zynqmp_ipi_mbox *mbox;
 	int num_mboxes, ret = -EINVAL;
 
-	num_mboxes = of_get_child_count(np);
-	pdata = devm_kzalloc(dev, sizeof(*pdata) + (num_mboxes * sizeof(*mbox)),
+	num_mboxes = of_get_available_child_count(np);
+	if (num_mboxes == 0) {
+		dev_err(dev, "mailbox nodes not available\n");
+		return -EINVAL;
+	}
+
+	pdata = devm_kzalloc(dev, struct_size(pdata, ipi_mboxes, num_mboxes),
 			     GFP_KERNEL);
 	if (!pdata)
 		return -ENOMEM;
@@ -647,8 +654,6 @@
 	}
 
 	pdata->num_mboxes = num_mboxes;
-	pdata->ipi_mboxes = (struct zynqmp_ipi_mbox *)
-			    ((char *)pdata + sizeof(*pdata));
 
 	mbox = pdata->ipi_mboxes;
 	for_each_available_child_of_node(np, nc) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mcb/mcb-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mcb/mcb-core.c
@@ -71,8 +71,10 @@
 
 	get_device(dev);
 	ret = mdrv->probe(mdev, found_id);
-	if (ret)
+	if (ret) {
 		module_put(carrier_mod);
+		put_device(dev);
+	}
 
 	return ret;
 }
@@ -244,6 +246,7 @@
 	return 0;
 
 out:
+	put_device(&dev->dev);
 
 	return ret;
 }
@@ -385,17 +388,13 @@
 
 static int __mcb_bus_add_devices(struct device *dev, void *data)
 {
-	struct mcb_device *mdev = to_mcb_device(dev);
 	int retval;
 
-	if (mdev->is_added)
-		return 0;
-
 	retval = device_attach(dev);
-	if (retval < 0)
+	if (retval < 0) {
 		dev_err(dev, "Error adding device (%d)\n", retval);
-
-	mdev->is_added = true;
+		return retval;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mcb/mcb-lpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mcb/mcb-lpc.c
@@ -23,7 +23,7 @@
 {
 	struct resource *res;
 	struct priv *priv;
-	int ret = 0;
+	int ret = 0, table_size;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -58,16 +58,43 @@
 
 	ret = chameleon_parse_cells(priv->bus, priv->mem->start, priv->base);
 	if (ret < 0) {
-		mcb_release_bus(priv->bus);
-		return ret;
+		goto out_mcb_bus;
 	}
 
-	dev_dbg(&pdev->dev, "Found %d cells\n", ret);
+	table_size = ret;
+
+	if (table_size < CHAM_HEADER_SIZE) {
+		/* Release the previous resources */
+		devm_iounmap(&pdev->dev, priv->base);
+		devm_release_mem_region(&pdev->dev, priv->mem->start, resource_size(priv->mem));
+
+		/* Then, allocate it again with the actual chameleon table size */
+		res = devm_request_mem_region(&pdev->dev, priv->mem->start,
+					      table_size,
+					      KBUILD_MODNAME);
+		if (!res) {
+			dev_err(&pdev->dev, "Failed to request PCI memory\n");
+			ret = -EBUSY;
+			goto out_mcb_bus;
+		}
+
+		priv->base = devm_ioremap(&pdev->dev, priv->mem->start, table_size);
+		if (!priv->base) {
+			dev_err(&pdev->dev, "Cannot ioremap\n");
+			ret = -ENOMEM;
+			goto out_mcb_bus;
+		}
+
+		platform_set_drvdata(pdev, priv);
+	}
 
 	mcb_bus_add_devices(priv->bus);
 
 	return 0;
 
+out_mcb_bus:
+	mcb_release_bus(priv->bus);
+	return ret;
 }
 
 static int mcb_lpc_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mcb/mcb-parse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mcb/mcb-parse.c
@@ -99,8 +99,6 @@
 	mdev->mem.end = mdev->mem.start + size - 1;
 	mdev->mem.flags = IORESOURCE_MEM;
 
-	mdev->is_added = false;
-
 	ret = mcb_device_register(bus, mdev);
 	if (ret < 0)
 		goto err;
@@ -130,7 +128,7 @@
 	}
 }
 
-static int chameleon_get_bar(char __iomem **base, phys_addr_t mapbase,
+static int chameleon_get_bar(void __iomem **base, phys_addr_t mapbase,
 			     struct chameleon_bar **cb)
 {
 	struct chameleon_bar *c;
@@ -179,12 +177,13 @@
 {
 	struct chameleon_fpga_header *header;
 	struct chameleon_bar *cb;
-	char __iomem *p = base;
+	void __iomem *p = base;
 	int num_cells = 0;
 	uint32_t dtype;
 	int bar_count;
 	int ret;
 	u32 hsize;
+	u32 table_size;
 
 	hsize = sizeof(struct chameleon_fpga_header);
 
@@ -239,12 +238,16 @@
 		num_cells++;
 	}
 
-	if (num_cells == 0)
-		num_cells = -EINVAL;
+	if (num_cells == 0) {
+		ret = -EINVAL;
+		goto free_bar;
+	}
 
+	table_size = p - base;
+	pr_debug("%d cell(s) found. Chameleon table size: 0x%04x bytes\n", num_cells, table_size);
 	kfree(cb);
 	kfree(header);
-	return num_cells;
+	return table_size;
 
 free_bar:
 	kfree(cb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mcb/mcb-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mcb/mcb-pci.c
@@ -31,7 +31,7 @@
 {
 	struct resource *res;
 	struct priv *priv;
-	int ret;
+	int ret, table_size;
 	unsigned long flags;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(struct priv), GFP_KERNEL);
@@ -90,7 +90,30 @@
 	if (ret < 0)
 		goto out_mcb_bus;
 
-	dev_dbg(&pdev->dev, "Found %d cells\n", ret);
+	table_size = ret;
+
+	if (table_size < CHAM_HEADER_SIZE) {
+		/* Release the previous resources */
+		devm_iounmap(&pdev->dev, priv->base);
+		devm_release_mem_region(&pdev->dev, priv->mapbase, CHAM_HEADER_SIZE);
+
+		/* Then, allocate it again with the actual chameleon table size */
+		res = devm_request_mem_region(&pdev->dev, priv->mapbase,
+						table_size,
+						KBUILD_MODNAME);
+		if (!res) {
+			dev_err(&pdev->dev, "Failed to request PCI memory\n");
+			ret = -EBUSY;
+			goto out_mcb_bus;
+		}
+
+		priv->base = devm_ioremap(&pdev->dev, priv->mapbase, table_size);
+		if (!priv->base) {
+			dev_err(&pdev->dev, "Cannot ioremap\n");
+			ret = -ENOMEM;
+			goto out_mcb_bus;
+		}
+	}
 
 	mcb_bus_add_devices(priv->bus);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/Kconfig
@@ -16,6 +16,10 @@
 config BLK_DEV_MD
 	tristate "RAID support"
 	select BLOCK_HOLDER_DEPRECATED if SYSFS
+	# BLOCK_LEGACY_AUTOLOAD requirement should be removed
+	# after relevant mdadm enhancements - to make "names=yes"
+	# the default - are widely available.
+	select BLOCK_LEGACY_AUTOLOAD
 	help
 	  This driver lets you combine several hard disk partitions into one
 	  logical block device. This can be used to simply append one
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/bcache.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/bcache.h
@@ -265,6 +265,7 @@
 #define BCACHE_DEV_WB_RUNNING		3
 #define BCACHE_DEV_RATE_DW_RUNNING	4
 	int			nr_stripes;
+#define BCH_MIN_STRIPE_SZ		((4 << 20) >> SECTOR_SHIFT)
 	unsigned int		stripe_size;
 	atomic_t		*stripe_sectors_dirty;
 	unsigned long		*full_dirty_stripes;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/bset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/bset.c
@@ -54,7 +54,7 @@
 int __bch_count_data(struct btree_keys *b)
 {
 	unsigned int ret = 0;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct bkey *k;
 
 	if (b->ops->is_extents)
@@ -67,7 +67,7 @@
 {
 	va_list args;
 	struct bkey *k, *p = NULL;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	const char *err;
 
 	for_each_key(b, k, &iter) {
@@ -879,7 +879,7 @@
 	unsigned int status = BTREE_INSERT_STATUS_NO_INSERT;
 	struct bset *i = bset_tree_last(b)->data;
 	struct bkey *m, *prev = NULL;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct bkey preceding_key_on_stack = ZERO_KEY;
 	struct bkey *preceding_key_p = &preceding_key_on_stack;
 
@@ -895,9 +895,9 @@
 	else
 		preceding_key(k, &preceding_key_p);
 
-	m = bch_btree_iter_init(b, &iter, preceding_key_p);
+	m = bch_btree_iter_stack_init(b, &iter, preceding_key_p);
 
-	if (b->ops->insert_fixup(b, k, &iter, replace_key))
+	if (b->ops->insert_fixup(b, k, &iter.iter, replace_key))
 		return status;
 
 	status = BTREE_INSERT_STATUS_INSERT;
@@ -1100,33 +1100,33 @@
 				 btree_iter_cmp));
 }
 
-static struct bkey *__bch_btree_iter_init(struct btree_keys *b,
-					  struct btree_iter *iter,
-					  struct bkey *search,
-					  struct bset_tree *start)
+static struct bkey *__bch_btree_iter_stack_init(struct btree_keys *b,
+						struct btree_iter_stack *iter,
+						struct bkey *search,
+						struct bset_tree *start)
 {
 	struct bkey *ret = NULL;
 
-	iter->size = ARRAY_SIZE(iter->data);
-	iter->used = 0;
+	iter->iter.size = ARRAY_SIZE(iter->stack_data);
+	iter->iter.used = 0;
 
 #ifdef CONFIG_BCACHE_DEBUG
-	iter->b = b;
+	iter->iter.b = b;
 #endif
 
 	for (; start <= bset_tree_last(b); start++) {
 		ret = bch_bset_search(b, start, search);
-		bch_btree_iter_push(iter, ret, bset_bkey_last(start->data));
+		bch_btree_iter_push(&iter->iter, ret, bset_bkey_last(start->data));
 	}
 
 	return ret;
 }
 
-struct bkey *bch_btree_iter_init(struct btree_keys *b,
-				 struct btree_iter *iter,
+struct bkey *bch_btree_iter_stack_init(struct btree_keys *b,
+				 struct btree_iter_stack *iter,
 				 struct bkey *search)
 {
-	return __bch_btree_iter_init(b, iter, search, b->set);
+	return __bch_btree_iter_stack_init(b, iter, search, b->set);
 }
 
 static inline struct bkey *__bch_btree_iter_next(struct btree_iter *iter,
@@ -1293,10 +1293,10 @@
 			    struct bset_sort_state *state)
 {
 	size_t order = b->page_order, keys = 0;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	int oldsize = bch_count_data(b);
 
-	__bch_btree_iter_init(b, &iter, NULL, &b->set[start]);
+	__bch_btree_iter_stack_init(b, &iter, NULL, &b->set[start]);
 
 	if (start) {
 		unsigned int i;
@@ -1307,7 +1307,7 @@
 		order = get_order(__set_bytes(b->set->data, keys));
 	}
 
-	__btree_sort(b, &iter, start, order, false, state);
+	__btree_sort(b, &iter.iter, start, order, false, state);
 
 	EBUG_ON(oldsize >= 0 && bch_count_data(b) != oldsize);
 }
@@ -1323,11 +1323,11 @@
 			 struct bset_sort_state *state)
 {
 	uint64_t start_time = local_clock();
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 
-	bch_btree_iter_init(b, &iter, NULL);
+	bch_btree_iter_stack_init(b, &iter, NULL);
 
-	btree_mergesort(b, new->set->data, &iter, false, true);
+	btree_mergesort(b, new->set->data, &iter.iter, false, true);
 
 	bch_time_stats_update(&state->time, start_time);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/bset.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/bset.h
@@ -321,7 +321,14 @@
 #endif
 	struct btree_iter_set {
 		struct bkey *k, *end;
-	} data[MAX_BSETS];
+	} data[];
+};
+
+/* Fixed-size btree_iter that can be allocated on the stack */
+
+struct btree_iter_stack {
+	struct btree_iter iter;
+	struct btree_iter_set stack_data[MAX_BSETS];
 };
 
 typedef bool (*ptr_filter_fn)(struct btree_keys *b, const struct bkey *k);
@@ -333,9 +340,9 @@
 
 void bch_btree_iter_push(struct btree_iter *iter, struct bkey *k,
 			 struct bkey *end);
-struct bkey *bch_btree_iter_init(struct btree_keys *b,
-				 struct btree_iter *iter,
-				 struct bkey *search);
+struct bkey *bch_btree_iter_stack_init(struct btree_keys *b,
+				       struct btree_iter_stack *iter,
+				       struct bkey *search);
 
 struct bkey *__bch_bset_search(struct btree_keys *b, struct bset_tree *t,
 			       const struct bkey *search);
@@ -350,13 +357,14 @@
 	return search ? __bch_bset_search(b, t, search) : t->data->start;
 }
 
-#define for_each_key_filter(b, k, iter, filter)				\
-	for (bch_btree_iter_init((b), (iter), NULL);			\
-	     ((k) = bch_btree_iter_next_filter((iter), (b), filter));)
-
-#define for_each_key(b, k, iter)					\
-	for (bch_btree_iter_init((b), (iter), NULL);			\
-	     ((k) = bch_btree_iter_next(iter));)
+#define for_each_key_filter(b, k, stack_iter, filter)                      \
+	for (bch_btree_iter_stack_init((b), (stack_iter), NULL);           \
+	     ((k) = bch_btree_iter_next_filter(&((stack_iter)->iter), (b), \
+					       filter));)
+
+#define for_each_key(b, k, stack_iter)                           \
+	for (bch_btree_iter_stack_init((b), (stack_iter), NULL); \
+	     ((k) = bch_btree_iter_next(&((stack_iter)->iter)));)
 
 /* Sorting */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/btree.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/btree.c
@@ -378,7 +378,7 @@
 		struct bvec_iter_all iter_all;
 
 		bio_for_each_segment_all(bv, b->bio, iter_all) {
-			memcpy(bvec_virt(bv), addr, PAGE_SIZE);
+			memcpy(page_address(bv->bv_page), addr, PAGE_SIZE);
 			addr += PAGE_SIZE;
 		}
 
@@ -885,7 +885,7 @@
  * cannibalize_bucket() will take. This means every time we unlock the root of
  * the btree, we need to release this lock if we have it held.
  */
-static void bch_cannibalize_unlock(struct cache_set *c)
+void bch_cannibalize_unlock(struct cache_set *c)
 {
 	spin_lock(&c->btree_cannibalize_lock);
 	if (c->btree_cache_alloc_lock == current) {
@@ -974,6 +974,9 @@
  *
  * The btree node will have either a read or a write lock held, depending on
  * level and op->lock.
+ *
+ * Note: Only error code or btree pointer will be returned, it is unncessary
+ *       for callers to check NULL pointer.
  */
 struct btree *bch_btree_node_get(struct cache_set *c, struct btree_op *op,
 				 struct bkey *k, int level, bool write,
@@ -1085,15 +1088,21 @@
 	mutex_unlock(&b->c->bucket_lock);
 }
 
+/*
+ * Only error code or btree pointer will be returned, it is unncessary for
+ * callers to check NULL pointer.
+ */
 struct btree *__bch_btree_node_alloc(struct cache_set *c, struct btree_op *op,
 				     int level, bool wait,
 				     struct btree *parent)
 {
 	BKEY_PADDED(key) k;
-	struct btree *b = ERR_PTR(-EAGAIN);
+	struct btree *b;
 
 	mutex_lock(&c->bucket_lock);
 retry:
+	/* return ERR_PTR(-EAGAIN) when it fails */
+	b = ERR_PTR(-EAGAIN);
 	if (__bch_bucket_alloc_set(c, RESERVE_BTREE, &k.key, wait))
 		goto err;
 
@@ -1138,7 +1147,7 @@
 {
 	struct btree *n = bch_btree_node_alloc(b->c, op, b->level, b->parent);
 
-	if (!IS_ERR_OR_NULL(n)) {
+	if (!IS_ERR(n)) {
 		mutex_lock(&n->write_lock);
 		bch_btree_sort_into(&b->keys, &n->keys, &b->c->sort);
 		bkey_copy_key(&n->key, &b->key);
@@ -1274,7 +1283,7 @@
 	uint8_t stale = 0;
 	unsigned int keys = 0, good_keys = 0;
 	struct bkey *k;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct bset_tree *t;
 
 	gc->nodes++;
@@ -1352,7 +1361,7 @@
 
 	for (i = 0; i < nodes; i++) {
 		new_nodes[i] = btree_node_alloc_replacement(r[i].b, NULL);
-		if (IS_ERR_OR_NULL(new_nodes[i]))
+		if (IS_ERR(new_nodes[i]))
 			goto out_nocoalesce;
 	}
 
@@ -1504,6 +1513,8 @@
 		return 0;
 
 	n = btree_node_alloc_replacement(replace, NULL);
+	if (IS_ERR(n))
+		return 0;
 
 	/* recheck reserve after allocating replacement node */
 	if (btree_check_reserve(b, NULL)) {
@@ -1533,7 +1544,7 @@
 static unsigned int btree_gc_count_keys(struct btree *b)
 {
 	struct bkey *k;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	unsigned int ret = 0;
 
 	for_each_key_filter(&b->keys, k, &iter, bch_ptr_bad)
@@ -1574,17 +1585,18 @@
 	int ret = 0;
 	bool should_rewrite;
 	struct bkey *k;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct gc_merge_info r[GC_MERGE_NODES];
 	struct gc_merge_info *i, *last = r + ARRAY_SIZE(r) - 1;
 
-	bch_btree_iter_init(&b->keys, &iter, &b->c->gc_done);
+	bch_btree_iter_stack_init(&b->keys, &iter, &b->c->gc_done);
 
 	for (i = r; i < r + ARRAY_SIZE(r); i++)
 		i->b = ERR_PTR(-EINTR);
 
 	while (1) {
-		k = bch_btree_iter_next_filter(&iter, &b->keys, bch_ptr_bad);
+		k = bch_btree_iter_next_filter(&iter.iter, &b->keys,
+					       bch_ptr_bad);
 		if (k) {
 			r->b = bch_btree_node_get(b->c, op, k, b->level - 1,
 						  true, b);
@@ -1669,7 +1681,7 @@
 	if (should_rewrite) {
 		n = btree_node_alloc_replacement(b, NULL);
 
-		if (!IS_ERR_OR_NULL(n)) {
+		if (!IS_ERR(n)) {
 			bch_btree_node_write_sync(n);
 
 			bch_btree_set_root(n);
@@ -1874,7 +1886,7 @@
 {
 	int ret = 0;
 	struct bkey *k, *p = NULL;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 
 	for_each_key_filter(&b->keys, k, &iter, bch_ptr_invalid)
 		bch_initial_mark_key(b->c, b->level, k);
@@ -1882,10 +1894,10 @@
 	bch_initial_mark_key(b->c, b->level + 1, &b->key);
 
 	if (b->level) {
-		bch_btree_iter_init(&b->keys, &iter, NULL);
+		bch_btree_iter_stack_init(&b->keys, &iter, NULL);
 
 		do {
-			k = bch_btree_iter_next_filter(&iter, &b->keys,
+			k = bch_btree_iter_next_filter(&iter.iter, &b->keys,
 						       bch_ptr_bad);
 			if (k) {
 				btree_node_prefetch(b, k);
@@ -1913,7 +1925,7 @@
 	struct btree_check_info *info = arg;
 	struct btree_check_state *check_state = info->state;
 	struct cache_set *c = check_state->c;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct bkey *k, *p;
 	int cur_idx, prev_idx, skip_nr;
 
@@ -1922,8 +1934,8 @@
 	ret = 0;
 
 	/* root node keys are checked before thread created */
-	bch_btree_iter_init(&c->root->keys, &iter, NULL);
-	k = bch_btree_iter_next_filter(&iter, &c->root->keys, bch_ptr_bad);
+	bch_btree_iter_stack_init(&c->root->keys, &iter, NULL);
+	k = bch_btree_iter_next_filter(&iter.iter, &c->root->keys, bch_ptr_bad);
 	BUG_ON(!k);
 
 	p = k;
@@ -1941,7 +1953,7 @@
 		skip_nr = cur_idx - prev_idx;
 
 		while (skip_nr) {
-			k = bch_btree_iter_next_filter(&iter,
+			k = bch_btree_iter_next_filter(&iter.iter,
 						       &c->root->keys,
 						       bch_ptr_bad);
 			if (k)
@@ -1968,6 +1980,15 @@
 			c->gc_stats.nodes++;
 			bch_btree_op_init(&op, 0);
 			ret = bcache_btree(check_recurse, p, c->root, &op);
+			/*
+			 * The op may be added to cache_set's btree_cache_wait
+			 * in mca_cannibalize(), must ensure it is removed from
+			 * the list and release btree_cache_alloc_lock before
+			 * free op memory.
+			 * Otherwise, the btree_cache_wait will be damaged.
+			 */
+			bch_cannibalize_unlock(c);
+			finish_wait(&c->btree_cache_wait, &(&op)->wait);
 			if (ret)
 				goto out;
 		}
@@ -2005,9 +2026,8 @@
 	int ret = 0;
 	int i;
 	struct bkey *k = NULL;
-	struct btree_iter iter;
-	struct btree_check_state *check_state;
-	char name[32];
+	struct btree_iter_stack iter;
+	struct btree_check_state check_state;
 
 	/* check and mark root node keys */
 	for_each_key_filter(&c->root->keys, k, &iter, bch_ptr_invalid)
@@ -2018,61 +2038,59 @@
 	if (c->root->level == 0)
 		return 0;
 
-	check_state = kzalloc(sizeof(struct btree_check_state), GFP_KERNEL);
-	if (!check_state)
-		return -ENOMEM;
-
-	check_state->c = c;
-	check_state->total_threads = bch_btree_chkthread_nr();
-	check_state->key_idx = 0;
-	spin_lock_init(&check_state->idx_lock);
-	atomic_set(&check_state->started, 0);
-	atomic_set(&check_state->enough, 0);
-	init_waitqueue_head(&check_state->wait);
+	memset(&check_state, 0, sizeof(struct btree_check_state));
+	check_state.c = c;
+	check_state.total_threads = bch_btree_chkthread_nr();
+	check_state.key_idx = 0;
+	spin_lock_init(&check_state.idx_lock);
+	atomic_set(&check_state.started, 0);
+	atomic_set(&check_state.enough, 0);
+	init_waitqueue_head(&check_state.wait);
 
+	rw_lock(0, c->root, c->root->level);
 	/*
 	 * Run multiple threads to check btree nodes in parallel,
-	 * if check_state->enough is non-zero, it means current
+	 * if check_state.enough is non-zero, it means current
 	 * running check threads are enough, unncessary to create
 	 * more.
 	 */
-	for (i = 0; i < check_state->total_threads; i++) {
-		/* fetch latest check_state->enough earlier */
+	for (i = 0; i < check_state.total_threads; i++) {
+		/* fetch latest check_state.enough earlier */
 		smp_mb__before_atomic();
-		if (atomic_read(&check_state->enough))
+		if (atomic_read(&check_state.enough))
 			break;
 
-		check_state->infos[i].result = 0;
-		check_state->infos[i].state = check_state;
-		snprintf(name, sizeof(name), "bch_btrchk[%u]", i);
-		atomic_inc(&check_state->started);
+		check_state.infos[i].result = 0;
+		check_state.infos[i].state = &check_state;
 
-		check_state->infos[i].thread =
+		check_state.infos[i].thread =
 			kthread_run(bch_btree_check_thread,
-				    &check_state->infos[i],
-				    name);
-		if (IS_ERR(check_state->infos[i].thread)) {
+				    &check_state.infos[i],
+				    "bch_btrchk[%d]", i);
+		if (IS_ERR(check_state.infos[i].thread)) {
 			pr_err("fails to run thread bch_btrchk[%d]\n", i);
 			for (--i; i >= 0; i--)
-				kthread_stop(check_state->infos[i].thread);
+				kthread_stop(check_state.infos[i].thread);
 			ret = -ENOMEM;
 			goto out;
 		}
+		atomic_inc(&check_state.started);
 	}
 
-	wait_event_interruptible(check_state->wait,
-				 atomic_read(&check_state->started) == 0 ||
-				  test_bit(CACHE_SET_IO_DISABLE, &c->flags));
-
-	for (i = 0; i < check_state->total_threads; i++) {
-		if (check_state->infos[i].result) {
-			ret = check_state->infos[i].result;
+	/*
+	 * Must wait for all threads to stop.
+	 */
+	wait_event(check_state.wait, atomic_read(&check_state.started) == 0);
+
+	for (i = 0; i < check_state.total_threads; i++) {
+		if (check_state.infos[i].result) {
+			ret = check_state.infos[i].result;
 			goto out;
 		}
 	}
 
 out:
-	kfree(check_state);
+	rw_unlock(0, c->root);
 	return ret;
 }
 
@@ -2504,11 +2522,11 @@
 
 	if (b->level) {
 		struct bkey *k;
-		struct btree_iter iter;
+		struct btree_iter_stack iter;
 
-		bch_btree_iter_init(&b->keys, &iter, from);
+		bch_btree_iter_stack_init(&b->keys, &iter, from);
 
-		while ((k = bch_btree_iter_next_filter(&iter, &b->keys,
+		while ((k = bch_btree_iter_next_filter(&iter.iter, &b->keys,
 						       bch_ptr_bad))) {
 			ret = bcache_btree(map_nodes_recurse, k, b,
 				    op, from, fn, flags);
@@ -2537,11 +2555,12 @@
 {
 	int ret = MAP_CONTINUE;
 	struct bkey *k;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 
-	bch_btree_iter_init(&b->keys, &iter, from);
+	bch_btree_iter_stack_init(&b->keys, &iter, from);
 
-	while ((k = bch_btree_iter_next_filter(&iter, &b->keys, bch_ptr_bad))) {
+	while ((k = bch_btree_iter_next_filter(&iter.iter, &b->keys,
+					       bch_ptr_bad))) {
 		ret = !b->level
 			? fn(op, b, k)
 			: bcache_btree(map_keys_recurse, k,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/btree.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/btree.h
@@ -226,7 +226,7 @@
 	int				result;
 };
 
-#define BCH_BTR_CHKTHREAD_MAX	64
+#define BCH_BTR_CHKTHREAD_MAX	12
 struct btree_check_state {
 	struct cache_set		*c;
 	int				total_threads;
@@ -282,6 +282,7 @@
 void bch_moving_gc(struct cache_set *c);
 int bch_btree_check(struct cache_set *c);
 void bch_initial_mark_key(struct cache_set *c, int level, struct bkey *k);
+void bch_cannibalize_unlock(struct cache_set *c);
 
 static inline void wake_up_gc(struct cache_set *c)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/closure.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/closure.c
@@ -17,10 +17,16 @@
 {
 	int r = flags & CLOSURE_REMAINING_MASK;
 
-	BUG_ON(flags & CLOSURE_GUARD_MASK);
-	BUG_ON(!r && (flags & ~CLOSURE_DESTRUCTOR));
+	if (WARN(flags & CLOSURE_GUARD_MASK,
+		 "closure has guard bits set: %x (%u)",
+		 flags & CLOSURE_GUARD_MASK, (unsigned) __fls(r)))
+		r &= ~CLOSURE_GUARD_MASK;
 
 	if (!r) {
+		WARN(flags & ~CLOSURE_DESTRUCTOR,
+		     "closure ref hit 0 with incorrect flags set: %x (%u)",
+		     flags & ~CLOSURE_DESTRUCTOR, (unsigned) __fls(flags));
+
 		if (cl->fn && !(flags & CLOSURE_DESTRUCTOR)) {
 			atomic_set(&cl->remaining,
 				   CLOSURE_REMAINING_INITIALIZER);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/journal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/journal.c
@@ -407,6 +407,11 @@
 	return ret;
 }
 
+void bch_journal_space_reserve(struct journal *j)
+{
+	j->do_reserve = true;
+}
+
 /* Journalling */
 
 static void btree_flush_write(struct cache_set *c)
@@ -625,12 +630,30 @@
 	}
 }
 
+static unsigned int free_journal_buckets(struct cache_set *c)
+{
+	struct journal *j = &c->journal;
+	struct cache *ca = c->cache;
+	struct journal_device *ja = &c->cache->journal;
+	unsigned int n;
+
+	/* In case njournal_buckets is not power of 2 */
+	if (ja->cur_idx >= ja->discard_idx)
+		n = ca->sb.njournal_buckets +  ja->discard_idx - ja->cur_idx;
+	else
+		n = ja->discard_idx - ja->cur_idx;
+
+	if (n > (1 + j->do_reserve))
+		return n - (1 + j->do_reserve);
+
+	return 0;
+}
+
 static void journal_reclaim(struct cache_set *c)
 {
 	struct bkey *k = &c->journal.key;
 	struct cache *ca = c->cache;
 	uint64_t last_seq;
-	unsigned int next;
 	struct journal_device *ja = &ca->journal;
 	atomic_t p __maybe_unused;
 
@@ -653,12 +676,10 @@
 	if (c->journal.blocks_free)
 		goto out;
 
-	next = (ja->cur_idx + 1) % ca->sb.njournal_buckets;
-	/* No space available on this device */
-	if (next == ja->discard_idx)
+	if (!free_journal_buckets(c))
 		goto out;
 
-	ja->cur_idx = next;
+	ja->cur_idx = (ja->cur_idx + 1) % ca->sb.njournal_buckets;
 	k->ptr[0] = MAKE_PTR(0,
 			     bucket_to_sector(c, ca->sb.d[ja->cur_idx]),
 			     ca->sb.nr_this_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/journal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/journal.h
@@ -105,6 +105,7 @@
 	spinlock_t		lock;
 	spinlock_t		flush_write_lock;
 	bool			btree_flushing;
+	bool			do_reserve;
 	/* used when waiting because the journal was full */
 	struct closure_waitlist	wait;
 	struct closure		io;
@@ -182,5 +183,6 @@
 
 void bch_journal_free(struct cache_set *c);
 int bch_journal_alloc(struct cache_set *c);
+void bch_journal_space_reserve(struct journal *j);
 
 #endif /* _BCACHE_JOURNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/request.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/request.c
@@ -1107,6 +1107,12 @@
 	 * which would call closure_get(&dc->disk.cl)
 	 */
 	ddip = kzalloc(sizeof(struct detached_dev_io_private), GFP_NOIO);
+	if (!ddip) {
+		bio->bi_status = BLK_STS_RESOURCE;
+		bio->bi_end_io(bio);
+		return;
+	}
+
 	ddip->d = d;
 	/* Count on the bcache device */
 	ddip->orig_bdev = orig_bdev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/super.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/super.c
@@ -885,9 +885,9 @@
 		bcache_device_detach(d);
 
 	if (disk) {
-		blk_cleanup_disk(disk);
 		ida_simple_remove(&bcache_device_idx,
 				  first_minor_to_idx(disk->first_minor));
+		blk_cleanup_disk(disk);
 	}
 
 	bioset_exit(&d->bio_split);
@@ -909,6 +909,8 @@
 
 	if (!d->stripe_size)
 		d->stripe_size = 1 << 31;
+	else if (d->stripe_size < BCH_MIN_STRIPE_SZ)
+		d->stripe_size = roundup(BCH_MIN_STRIPE_SZ, d->stripe_size);
 
 	n = DIV_ROUND_UP_ULL(sectors, d->stripe_size);
 	if (!n || n > max_stripes) {
@@ -1918,8 +1920,9 @@
 	INIT_LIST_HEAD(&c->btree_cache_freed);
 	INIT_LIST_HEAD(&c->data_buckets);
 
-	iter_size = ((meta_bucket_pages(sb) * PAGE_SECTORS) / sb->block_size + 1) *
-		sizeof(struct btree_iter_set);
+	iter_size = sizeof(struct btree_iter) +
+		    ((meta_bucket_pages(sb) * PAGE_SECTORS) / sb->block_size) *
+			    sizeof(struct btree_iter_set);
 
 	c->devices = kcalloc(c->nr_uuids, sizeof(void *), GFP_KERNEL);
 	if (!c->devices)
@@ -2022,7 +2025,7 @@
 		c->root = bch_btree_node_get(c, NULL, k,
 					     j->btree_level,
 					     true, NULL);
-		if (IS_ERR_OR_NULL(c->root))
+		if (IS_ERR(c->root))
 			goto err;
 
 		list_del_init(&c->root->list);
@@ -2093,7 +2096,7 @@
 
 		err = "cannot allocate new btree root";
 		c->root = __bch_btree_node_alloc(c, NULL, 0, true, NULL);
-		if (IS_ERR_OR_NULL(c->root))
+		if (IS_ERR(c->root))
 			goto err;
 
 		mutex_lock(&c->root->write_lock);
@@ -2131,6 +2134,7 @@
 
 	flash_devs_run(c);
 
+	bch_journal_space_reserve(&c->journal);
 	set_bit(CACHE_SET_RUNNING, &c->flags);
 	return 0;
 err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/sysfs.c
@@ -658,7 +658,7 @@
 	unsigned int bytes = 0;
 	struct bkey *k;
 	struct btree *b;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 
 	goto lock_root;
 
@@ -1099,7 +1099,7 @@
 			sum += INITIAL_PRIO - cached[i];
 
 		if (n)
-			do_div(sum, n);
+			sum = div64_u64(sum, n);
 
 		for (i = 0; i < ARRAY_SIZE(q); i++)
 			q[i] = INITIAL_PRIO - cached[n * (i + 1) /
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/writeback.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/writeback.c
@@ -157,6 +157,53 @@
 	dc->writeback_rate_target = target;
 }
 
+static bool idle_counter_exceeded(struct cache_set *c)
+{
+	int counter, dev_nr;
+
+	/*
+	 * If c->idle_counter is overflow (idel for really long time),
+	 * reset as 0 and not set maximum rate this time for code
+	 * simplicity.
+	 */
+	counter = atomic_inc_return(&c->idle_counter);
+	if (counter <= 0) {
+		atomic_set(&c->idle_counter, 0);
+		return false;
+	}
+
+	dev_nr = atomic_read(&c->attached_dev_nr);
+	if (dev_nr == 0)
+		return false;
+
+	/*
+	 * c->idle_counter is increased by writeback thread of all
+	 * attached backing devices, in order to represent a rough
+	 * time period, counter should be divided by dev_nr.
+	 * Otherwise the idle time cannot be larger with more backing
+	 * device attached.
+	 * The following calculation equals to checking
+	 *	(counter / dev_nr) < (dev_nr * 6)
+	 */
+	if (counter < (dev_nr * dev_nr * 6))
+		return false;
+
+	return true;
+}
+
+/*
+ * Idle_counter is increased every time when update_writeback_rate() is
+ * called. If all backing devices attached to the same cache set have
+ * identical dc->writeback_rate_update_seconds values, it is about 6
+ * rounds of update_writeback_rate() on each backing device before
+ * c->at_max_writeback_rate is set to 1, and then max wrteback rate set
+ * to each dc->writeback_rate.rate.
+ * In order to avoid extra locking cost for counting exact dirty cached
+ * devices number, c->attached_dev_nr is used to calculate the idle
+ * throushold. It might be bigger if not all cached device are in write-
+ * back mode, but it still works well with limited extra rounds of
+ * update_writeback_rate().
+ */
 static bool set_at_max_writeback_rate(struct cache_set *c,
 				       struct cached_dev *dc)
 {
@@ -167,21 +214,8 @@
 	/* Don't set max writeback rate if gc is running */
 	if (!c->gc_mark_valid)
 		return false;
-	/*
-	 * Idle_counter is increased everytime when update_writeback_rate() is
-	 * called. If all backing devices attached to the same cache set have
-	 * identical dc->writeback_rate_update_seconds values, it is about 6
-	 * rounds of update_writeback_rate() on each backing device before
-	 * c->at_max_writeback_rate is set to 1, and then max wrteback rate set
-	 * to each dc->writeback_rate.rate.
-	 * In order to avoid extra locking cost for counting exact dirty cached
-	 * devices number, c->attached_dev_nr is used to calculate the idle
-	 * throushold. It might be bigger if not all cached device are in write-
-	 * back mode, but it still works well with limited extra rounds of
-	 * update_writeback_rate().
-	 */
-	if (atomic_inc_return(&c->idle_counter) <
-	    atomic_read(&c->attached_dev_nr) * 6)
+
+	if (!idle_counter_exceeded(c))
 		return false;
 
 	if (atomic_read(&c->at_max_writeback_rate) != 1)
@@ -195,13 +229,10 @@
 	dc->writeback_rate_change = 0;
 
 	/*
-	 * Check c->idle_counter and c->at_max_writeback_rate agagain in case
-	 * new I/O arrives during before set_at_max_writeback_rate() returns.
-	 * Then the writeback rate is set to 1, and its new value should be
-	 * decided via __update_writeback_rate().
+	 * In case new I/O arrives during before
+	 * set_at_max_writeback_rate() returns.
 	 */
-	if ((atomic_read(&c->idle_counter) <
-	     atomic_read(&c->attached_dev_nr) * 6) ||
+	if (!idle_counter_exceeded(c) ||
 	    !atomic_read(&c->at_max_writeback_rate))
 		return false;
 
@@ -802,13 +833,11 @@
 
 /* Init */
 #define INIT_KEYS_EACH_TIME	500000
-#define INIT_KEYS_SLEEP_MS	100
 
 struct sectors_dirty_init {
 	struct btree_op	op;
 	unsigned int	inode;
 	size_t		count;
-	struct bkey	start;
 };
 
 static int sectors_dirty_init_fn(struct btree_op *_op, struct btree *b,
@@ -824,11 +853,8 @@
 					     KEY_START(k), KEY_SIZE(k));
 
 	op->count++;
-	if (atomic_read(&b->c->search_inflight) &&
-	    !(op->count % INIT_KEYS_EACH_TIME)) {
-		bkey_copy_key(&op->start, k);
-		return -EAGAIN;
-	}
+	if (!(op->count % INIT_KEYS_EACH_TIME))
+		cond_resched();
 
 	return MAP_CONTINUE;
 }
@@ -843,24 +869,26 @@
 	bch_btree_op_init(&op.op, -1);
 	op.inode = d->id;
 	op.count = 0;
-	op.start = KEY(op.inode, 0, 0);
 
-	do {
-		ret = bcache_btree(map_keys_recurse,
-				   k,
-				   c->root,
-				   &op.op,
-				   &op.start,
-				   sectors_dirty_init_fn,
-				   0);
-		if (ret == -EAGAIN)
-			schedule_timeout_interruptible(
-				msecs_to_jiffies(INIT_KEYS_SLEEP_MS));
-		else if (ret < 0) {
-			pr_warn("sectors dirty init failed, ret=%d!\n", ret);
-			break;
-		}
-	} while (ret == -EAGAIN);
+	ret = bcache_btree(map_keys_recurse,
+			   k,
+			   c->root,
+			   &op.op,
+			   &KEY(op.inode, 0, 0),
+			   sectors_dirty_init_fn,
+			   0);
+	if (ret < 0)
+		pr_warn("sectors dirty init failed, ret=%d!\n", ret);
+
+	/*
+	 * The op may be added to cache_set's btree_cache_wait
+	 * in mca_cannibalize(), must ensure it is removed from
+	 * the list and release btree_cache_alloc_lock before
+	 * free op memory.
+	 * Otherwise, the btree_cache_wait will be damaged.
+	 */
+	bch_cannibalize_unlock(c);
+	finish_wait(&c->btree_cache_wait, &(&op.op)->wait);
 
 	return ret;
 }
@@ -870,15 +898,15 @@
 	struct dirty_init_thrd_info *info = arg;
 	struct bch_dirty_init_state *state = info->state;
 	struct cache_set *c = state->c;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct bkey *k, *p;
 	int cur_idx, prev_idx, skip_nr;
 
 	k = p = NULL;
-	cur_idx = prev_idx = 0;
+	prev_idx = 0;
 
-	bch_btree_iter_init(&c->root->keys, &iter, NULL);
-	k = bch_btree_iter_next_filter(&iter, &c->root->keys, bch_ptr_bad);
+	bch_btree_iter_stack_init(&c->root->keys, &iter, NULL);
+	k = bch_btree_iter_next_filter(&iter.iter, &c->root->keys, bch_ptr_bad);
 	BUG_ON(!k);
 
 	p = k;
@@ -892,7 +920,7 @@
 		skip_nr = cur_idx - prev_idx;
 
 		while (skip_nr) {
-			k = bch_btree_iter_next_filter(&iter,
+			k = bch_btree_iter_next_filter(&iter.iter,
 						       &c->root->keys,
 						       bch_ptr_bad);
 			if (k)
@@ -904,7 +932,6 @@
 				goto out;
 			}
 			skip_nr--;
-			cond_resched();
 		}
 
 		if (p) {
@@ -914,7 +941,6 @@
 
 		p = NULL;
 		prev_idx = cur_idx;
-		cond_resched();
 	}
 
 out:
@@ -941,69 +967,72 @@
 void bch_sectors_dirty_init(struct bcache_device *d)
 {
 	int i;
+	struct btree *b = NULL;
 	struct bkey *k = NULL;
-	struct btree_iter iter;
+	struct btree_iter_stack iter;
 	struct sectors_dirty_init op;
 	struct cache_set *c = d->c;
-	struct bch_dirty_init_state *state;
-	char name[32];
+	struct bch_dirty_init_state state;
+
+retry_lock:
+	b = c->root;
+	rw_lock(0, b, b->level);
+	if (b != c->root) {
+		rw_unlock(0, b);
+		goto retry_lock;
+	}
 
 	/* Just count root keys if no leaf node */
 	if (c->root->level == 0) {
 		bch_btree_op_init(&op.op, -1);
 		op.inode = d->id;
 		op.count = 0;
-		op.start = KEY(op.inode, 0, 0);
 
 		for_each_key_filter(&c->root->keys,
-				    k, &iter, bch_ptr_invalid)
+				    k, &iter, bch_ptr_invalid) {
+			if (KEY_INODE(k) != op.inode)
+				continue;
 			sectors_dirty_init_fn(&op.op, c->root, k);
-		return;
-	}
+		}
 
-	state = kzalloc(sizeof(struct bch_dirty_init_state), GFP_KERNEL);
-	if (!state) {
-		pr_warn("sectors dirty init failed: cannot allocate memory\n");
+		rw_unlock(0, b);
 		return;
 	}
 
-	state->c = c;
-	state->d = d;
-	state->total_threads = bch_btre_dirty_init_thread_nr();
-	state->key_idx = 0;
-	spin_lock_init(&state->idx_lock);
-	atomic_set(&state->started, 0);
-	atomic_set(&state->enough, 0);
-	init_waitqueue_head(&state->wait);
+	memset(&state, 0, sizeof(struct bch_dirty_init_state));
+	state.c = c;
+	state.d = d;
+	state.total_threads = bch_btre_dirty_init_thread_nr();
+	state.key_idx = 0;
+	spin_lock_init(&state.idx_lock);
+	atomic_set(&state.started, 0);
+	atomic_set(&state.enough, 0);
+	init_waitqueue_head(&state.wait);
 
-	for (i = 0; i < state->total_threads; i++) {
-		/* Fetch latest state->enough earlier */
+	for (i = 0; i < state.total_threads; i++) {
+		/* Fetch latest state.enough earlier */
 		smp_mb__before_atomic();
-		if (atomic_read(&state->enough))
+		if (atomic_read(&state.enough))
 			break;
 
-		state->infos[i].state = state;
-		atomic_inc(&state->started);
-		snprintf(name, sizeof(name), "bch_dirty_init[%d]", i);
-
-		state->infos[i].thread =
-			kthread_run(bch_dirty_init_thread,
-				    &state->infos[i],
-				    name);
-		if (IS_ERR(state->infos[i].thread)) {
+		atomic_inc(&state.started);
+		state.infos[i].state = &state;
+		state.infos[i].thread =
+			kthread_run(bch_dirty_init_thread, &state.infos[i],
+				    "bch_dirtcnt[%d]", i);
+		if (IS_ERR(state.infos[i].thread)) {
 			pr_err("fails to run thread bch_dirty_init[%d]\n", i);
+			atomic_dec(&state.started);
 			for (--i; i >= 0; i--)
-				kthread_stop(state->infos[i].thread);
+				kthread_stop(state.infos[i].thread);
 			goto out;
 		}
 	}
 
-	wait_event_interruptible(state->wait,
-		 atomic_read(&state->started) == 0 ||
-		 test_bit(CACHE_SET_IO_DISABLE, &c->flags));
-
 out:
-	kfree(state);
+	/* Must wait for all threads to stop. */
+	wait_event(state.wait, atomic_read(&state.started) == 0);
+	rw_unlock(0, b);
 }
 
 void bch_cached_dev_writeback_init(struct cached_dev *dc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/bcache/writeback.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/bcache/writeback.h
@@ -20,7 +20,7 @@
 #define BCH_WRITEBACK_FRAGMENT_THRESHOLD_MID 57
 #define BCH_WRITEBACK_FRAGMENT_THRESHOLD_HIGH 64
 
-#define BCH_DIRTY_INIT_THRD_MAX	64
+#define BCH_DIRTY_INIT_THRD_MAX	12
 /*
  * 14 (16384ths) is chosen here as something that each backing device
  * should be a reasonable fraction of the share, and not to blow up
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-cache-metadata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-cache-metadata.c
@@ -551,11 +551,13 @@
 	return r;
 }
 
-static void __destroy_persistent_data_objects(struct dm_cache_metadata *cmd)
+static void __destroy_persistent_data_objects(struct dm_cache_metadata *cmd,
+					      bool destroy_bm)
 {
 	dm_sm_destroy(cmd->metadata_sm);
 	dm_tm_destroy(cmd->tm);
-	dm_block_manager_destroy(cmd->bm);
+	if (destroy_bm)
+		dm_block_manager_destroy(cmd->bm);
 }
 
 typedef unsigned long (*flags_mutator)(unsigned long);
@@ -826,7 +828,7 @@
 		cmd2 = lookup(bdev);
 		if (cmd2) {
 			mutex_unlock(&table_lock);
-			__destroy_persistent_data_objects(cmd);
+			__destroy_persistent_data_objects(cmd, true);
 			kfree(cmd);
 			return cmd2;
 		}
@@ -874,7 +876,7 @@
 		mutex_unlock(&table_lock);
 
 		if (!cmd->fail_io)
-			__destroy_persistent_data_objects(cmd);
+			__destroy_persistent_data_objects(cmd, true);
 		kfree(cmd);
 	}
 }
@@ -1808,14 +1810,52 @@
 
 int dm_cache_metadata_abort(struct dm_cache_metadata *cmd)
 {
-	int r;
+	int r = -EINVAL;
+	struct dm_block_manager *old_bm = NULL, *new_bm = NULL;
+
+	/* fail_io is double-checked with cmd->root_lock held below */
+	if (unlikely(cmd->fail_io))
+		return r;
+
+	/*
+	 * Replacement block manager (new_bm) is created and old_bm destroyed outside of
+	 * cmd root_lock to avoid ABBA deadlock that would result (due to life-cycle of
+	 * shrinker associated with the block manager's bufio client vs cmd root_lock).
+	 * - must take shrinker_rwsem without holding cmd->root_lock
+	 */
+	new_bm = dm_block_manager_create(cmd->bdev, DM_CACHE_METADATA_BLOCK_SIZE << SECTOR_SHIFT,
+					 CACHE_MAX_CONCURRENT_LOCKS);
 
 	WRITE_LOCK(cmd);
-	__destroy_persistent_data_objects(cmd);
-	r = __create_persistent_data_objects(cmd, false);
+	if (cmd->fail_io) {
+		WRITE_UNLOCK(cmd);
+		goto out;
+	}
+
+	__destroy_persistent_data_objects(cmd, false);
+	old_bm = cmd->bm;
+	if (IS_ERR(new_bm)) {
+		DMERR("could not create block manager during abort");
+		cmd->bm = NULL;
+		r = PTR_ERR(new_bm);
+		goto out_unlock;
+	}
+
+	cmd->bm = new_bm;
+	r = __open_or_format_metadata(cmd, false);
+	if (r) {
+		cmd->bm = NULL;
+		goto out_unlock;
+	}
+	new_bm = NULL;
+out_unlock:
 	if (r)
 		cmd->fail_io = true;
 	WRITE_UNLOCK(cmd);
+	dm_block_manager_destroy(old_bm);
+out:
+	if (new_bm && !IS_ERR(new_bm))
+		dm_block_manager_destroy(new_bm);
 
 	return r;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-cache-policy-smq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-cache-policy-smq.c
@@ -854,7 +854,13 @@
 
 	struct background_tracker *bg_work;
 
-	bool migrations_allowed;
+	bool migrations_allowed:1;
+
+	/*
+	 * If this is set the policy will try and clean the whole cache
+	 * even if the device is not idle.
+	 */
+	bool cleaner:1;
 };
 
 /*----------------------------------------------------------------*/
@@ -1133,7 +1139,7 @@
 	 * Cache entries may not be populated.  So we cannot rely on the
 	 * size of the clean queue.
 	 */
-	if (idle) {
+	if (idle || mq->cleaner) {
 		/*
 		 * We'd like to clean everything.
 		 */
@@ -1716,11 +1722,9 @@
 		*hotspot_block_size /= 2u;
 }
 
-static struct dm_cache_policy *__smq_create(dm_cblock_t cache_size,
-					    sector_t origin_size,
-					    sector_t cache_block_size,
-					    bool mimic_mq,
-					    bool migrations_allowed)
+static struct dm_cache_policy *
+__smq_create(dm_cblock_t cache_size, sector_t origin_size, sector_t cache_block_size,
+	     bool mimic_mq, bool migrations_allowed, bool cleaner)
 {
 	unsigned i;
 	unsigned nr_sentinels_per_queue = 2u * NR_CACHE_LEVELS;
@@ -1807,6 +1811,7 @@
 		goto bad_btracker;
 
 	mq->migrations_allowed = migrations_allowed;
+	mq->cleaner = cleaner;
 
 	return &mq->policy;
 
@@ -1830,21 +1835,24 @@
 					  sector_t origin_size,
 					  sector_t cache_block_size)
 {
-	return __smq_create(cache_size, origin_size, cache_block_size, false, true);
+	return __smq_create(cache_size, origin_size, cache_block_size,
+			    false, true, false);
 }
 
 static struct dm_cache_policy *mq_create(dm_cblock_t cache_size,
 					 sector_t origin_size,
 					 sector_t cache_block_size)
 {
-	return __smq_create(cache_size, origin_size, cache_block_size, true, true);
+	return __smq_create(cache_size, origin_size, cache_block_size,
+			    true, true, false);
 }
 
 static struct dm_cache_policy *cleaner_create(dm_cblock_t cache_size,
 					      sector_t origin_size,
 					      sector_t cache_block_size)
 {
-	return __smq_create(cache_size, origin_size, cache_block_size, false, false);
+	return __smq_create(cache_size, origin_size, cache_block_size,
+			    false, false, true);
 }
 
 /*----------------------------------------------------------------*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-cache-target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-cache-target.c
@@ -915,16 +915,16 @@
 	if (get_cache_mode(cache) >= CM_READ_ONLY)
 		return;
 
-	if (dm_cache_metadata_set_needs_check(cache->cmd)) {
-		DMERR("%s: failed to set 'needs_check' flag in metadata", dev_name);
-		set_cache_mode(cache, CM_FAIL);
-	}
-
 	DMERR_LIMIT("%s: aborting current metadata transaction", dev_name);
 	if (dm_cache_metadata_abort(cache->cmd)) {
 		DMERR("%s: failed to abort metadata transaction", dev_name);
 		set_cache_mode(cache, CM_FAIL);
 	}
+
+	if (dm_cache_metadata_set_needs_check(cache->cmd)) {
+		DMERR("%s: failed to set 'needs_check' flag in metadata", dev_name);
+		set_cache_mode(cache, CM_FAIL);
+	}
 }
 
 static void metadata_operation_failed(struct cache *cache, const char *op, int r)
@@ -1813,6 +1813,7 @@
 
 		else
 			commit_needed = process_bio(cache, bio) || commit_needed;
+		cond_resched();
 	}
 
 	if (commit_needed)
@@ -1835,6 +1836,7 @@
 	while ((bio = bio_list_pop(&bios))) {
 		bio->bi_status = BLK_STS_DM_REQUEUE;
 		bio_endio(bio);
+		cond_resched();
 	}
 }
 
@@ -1875,6 +1877,8 @@
 		r = mg_start(cache, op, NULL);
 		if (r)
 			break;
+
+		cond_resched();
 	}
 }
 
@@ -1895,6 +1899,7 @@
 	if (cache->prison)
 		dm_bio_prison_destroy_v2(cache->prison);
 
+	cancel_delayed_work_sync(&cache->waker);
 	if (cache->wq)
 		destroy_workqueue(cache->wq);
 
@@ -1983,7 +1988,6 @@
 	sector_t cache_sectors;
 
 	struct dm_dev *origin_dev;
-	sector_t origin_sectors;
 
 	uint32_t block_size;
 
@@ -2065,6 +2069,7 @@
 static int parse_origin_dev(struct cache_args *ca, struct dm_arg_set *as,
 			    char **error)
 {
+	sector_t origin_sectors;
 	int r;
 
 	if (!at_least_one_arg(as, error))
@@ -2077,8 +2082,8 @@
 		return r;
 	}
 
-	ca->origin_sectors = get_dev_size(ca->origin_dev);
-	if (ca->ti->len > ca->origin_sectors) {
+	origin_sectors = get_dev_size(ca->origin_dev);
+	if (ca->ti->len > origin_sectors) {
 		*error = "Device size larger than cached device";
 		return -EINVAL;
 	}
@@ -2387,7 +2392,7 @@
 
 	ca->metadata_dev = ca->origin_dev = ca->cache_dev = NULL;
 
-	origin_blocks = cache->origin_sectors = ca->origin_sectors;
+	origin_blocks = cache->origin_sectors = ti->len;
 	origin_blocks = block_div(origin_blocks, ca->block_size);
 	cache->origin_blocks = to_oblock(origin_blocks);
 
@@ -2875,19 +2880,19 @@
 static bool can_resize(struct cache *cache, dm_cblock_t new_size)
 {
 	if (from_cblock(new_size) > from_cblock(cache->cache_size)) {
-		if (cache->sized) {
-			DMERR("%s: unable to extend cache due to missing cache table reload",
-			      cache_device_name(cache));
-			return false;
-		}
+		DMERR("%s: unable to extend cache due to missing cache table reload",
+		      cache_device_name(cache));
+		return false;
 	}
 
 	/*
 	 * We can't drop a dirty block when shrinking the cache.
 	 */
-	while (from_cblock(new_size) < from_cblock(cache->cache_size)) {
-		new_size = to_cblock(from_cblock(new_size) + 1);
-		if (is_dirty(cache, new_size)) {
+	if (cache->loaded_mappings) {
+		new_size = to_cblock(find_next_bit(cache->dirty_bitset,
+						   from_cblock(cache->cache_size),
+						   from_cblock(new_size)));
+		if (new_size != cache->cache_size) {
 			DMERR("%s: unable to shrink cache; cache block %llu is dirty",
 			      cache_device_name(cache),
 			      (unsigned long long) from_cblock(new_size));
@@ -2923,20 +2928,15 @@
 	/*
 	 * Check to see if the cache has resized.
 	 */
-	if (!cache->sized) {
-		r = resize_cache_dev(cache, csize);
-		if (r)
-			return r;
-
-		cache->sized = true;
-
-	} else if (csize != cache->cache_size) {
+	if (!cache->sized || csize != cache->cache_size) {
 		if (!can_resize(cache, csize))
 			return -EINVAL;
 
 		r = resize_cache_dev(cache, csize);
 		if (r)
 			return r;
+
+		cache->sized = true;
 	}
 
 	if (!cache->loaded_mappings) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-clone-metadata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-clone-metadata.c
@@ -465,11 +465,6 @@
 
 /*---------------------------------------------------------------------------*/
 
-static size_t bitmap_size(unsigned long nr_bits)
-{
-	return BITS_TO_LONGS(nr_bits) * sizeof(long);
-}
-
 static int __dirty_map_init(struct dirty_map *dmap, unsigned long nr_words,
 			    unsigned long nr_regions)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-clone-target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-clone-target.c
@@ -1959,6 +1959,7 @@
 
 	mempool_exit(&clone->hydration_pool);
 	dm_kcopyd_client_destroy(clone->kcopyd_client);
+	cancel_delayed_work_sync(&clone->waker);
 	destroy_workqueue(clone->wq);
 	hash_table_exit(clone);
 	dm_clone_metadata_close(clone->cmd);
@@ -2213,6 +2214,7 @@
 	r = dm_register_target(&clone_target);
 	if (r < 0) {
 		DMERR("Failed to register clone target");
+		kmem_cache_destroy(_hydration_cache);
 		return r;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-core.h
@@ -21,6 +21,8 @@
 #include "dm-ima.h"
 
 #define DM_RESERVED_MAX_IOS		1024
+#define DM_MAX_TARGETS			1048576
+#define DM_MAX_TARGET_PARAMS		1024
 
 struct dm_kobject_holder {
 	struct kobject kobj;
@@ -65,6 +67,8 @@
 	struct gendisk *disk;
 	struct dax_device *dax_dev;
 
+	unsigned long __percpu *pending_io;
+
 	/*
 	 * A list of ios that arrived while we were suspended.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-crypt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-crypt.c
@@ -49,11 +49,12 @@
 struct convert_context {
 	struct completion restart;
 	struct bio *bio_in;
-	struct bio *bio_out;
 	struct bvec_iter iter_in;
+	struct bio *bio_out;
 	struct bvec_iter iter_out;
-	u64 cc_sector;
 	atomic_t cc_pending;
+	unsigned int tag_offset;
+	u64 cc_sector;
 	union {
 		struct skcipher_request *req;
 		struct aead_request *req_aead;
@@ -68,9 +69,9 @@
 	struct crypt_config *cc;
 	struct bio *base_bio;
 	u8 *integrity_metadata;
-	bool integrity_metadata_from_pool;
+	bool integrity_metadata_from_pool:1;
+
 	struct work_struct work;
-	struct tasklet_struct tasklet;
 
 	struct convert_context ctx;
 
@@ -1217,6 +1218,7 @@
 	if (bio_out)
 		ctx->iter_out = bio_out->bi_iter;
 	ctx->cc_sector = sector + cc->iv_offset;
+	ctx->tag_offset = 0;
 	init_completion(&ctx->restart);
 }
 
@@ -1542,7 +1544,6 @@
 static blk_status_t crypt_convert(struct crypt_config *cc,
 			 struct convert_context *ctx, bool atomic, bool reset_pending)
 {
-	unsigned int tag_offset = 0;
 	unsigned int sector_step = cc->sector_size >> SECTOR_SHIFT;
 	int r;
 
@@ -1565,9 +1566,9 @@
 		atomic_inc(&ctx->cc_pending);
 
 		if (crypt_integrity_aead(cc))
-			r = crypt_convert_block_aead(cc, ctx, ctx->r.req_aead, tag_offset);
+			r = crypt_convert_block_aead(cc, ctx, ctx->r.req_aead, ctx->tag_offset);
 		else
-			r = crypt_convert_block_skcipher(cc, ctx, ctx->r.req, tag_offset);
+			r = crypt_convert_block_skcipher(cc, ctx, ctx->r.req, ctx->tag_offset);
 
 		switch (r) {
 		/*
@@ -1587,8 +1588,8 @@
 					 * exit and continue processing in a workqueue
 					 */
 					ctx->r.req = NULL;
+					ctx->tag_offset++;
 					ctx->cc_sector += sector_step;
-					tag_offset++;
 					return BLK_STS_DEV_RESOURCE;
 				}
 			} else {
@@ -1602,8 +1603,8 @@
 		 */
 		case -EINPROGRESS:
 			ctx->r.req = NULL;
+			ctx->tag_offset++;
 			ctx->cc_sector += sector_step;
-			tag_offset++;
 			continue;
 		/*
 		 * The request was already processed (synchronously).
@@ -1611,7 +1612,7 @@
 		case 0:
 			atomic_dec(&ctx->cc_pending);
 			ctx->cc_sector += sector_step;
-			tag_offset++;
+			ctx->tag_offset++;
 			if (!atomic)
 				cond_resched();
 			continue;
@@ -1731,12 +1732,6 @@
 	atomic_inc(&io->io_pending);
 }
 
-static void kcryptd_io_bio_endio(struct work_struct *work)
-{
-	struct dm_crypt_io *io = container_of(work, struct dm_crypt_io, work);
-	bio_endio(io->base_bio);
-}
-
 /*
  * One of the bios was finished. Check for completion of
  * the whole request and correctly clean up the buffer.
@@ -1760,22 +1755,7 @@
 
 	base_bio->bi_status = error;
 
-	/*
-	 * If we are running this function from our tasklet,
-	 * we can't call bio_endio() here, because it will call
-	 * clone_endio() from dm.c, which in turn will
-	 * free the current struct dm_crypt_io structure with
-	 * our tasklet. In this case we need to delay bio_endio()
-	 * execution to after the tasklet is done and dequeued.
-	 */
-	if (tasklet_trylock(&io->tasklet)) {
-		tasklet_unlock(&io->tasklet);
-		bio_endio(base_bio);
-		return;
-	}
-
-	INIT_WORK(&io->work, kcryptd_io_bio_endio);
-	queue_work(cc->io_queue, &io->work);
+	bio_endio(base_bio);
 }
 
 /*
@@ -1935,6 +1915,7 @@
 			io = crypt_io_from_node(rb_first(&write_tree));
 			rb_erase(&io->rb_node, &write_tree);
 			kcryptd_io_write(io);
+			cond_resched();
 		} while (!RB_EMPTY_ROOT(&write_tree));
 		blk_finish_plug(&plug);
 	}
@@ -2013,7 +1994,6 @@
 	struct crypt_config *cc = io->cc;
 	struct convert_context *ctx = &io->ctx;
 	int crypt_finished;
-	sector_t sector = io->sector;
 	blk_status_t r;
 
 	wait_for_completion(&ctx->restart);
@@ -2030,10 +2010,8 @@
 	}
 
 	/* Encryption was already finished, submit io now */
-	if (crypt_finished) {
+	if (crypt_finished)
 		kcryptd_crypt_write_io_submit(io, 0);
-		io->sector = sector;
-	}
 
 	crypt_dec_pending(io);
 }
@@ -2044,14 +2022,13 @@
 	struct convert_context *ctx = &io->ctx;
 	struct bio *clone;
 	int crypt_finished;
-	sector_t sector = io->sector;
 	blk_status_t r;
 
 	/*
 	 * Prevent io from disappearing until this function completes.
 	 */
 	crypt_inc_pending(io);
-	crypt_convert_init(cc, ctx, NULL, io->base_bio, sector);
+	crypt_convert_init(cc, ctx, NULL, io->base_bio, io->sector);
 
 	clone = crypt_alloc_buffer(io, io->base_bio->bi_iter.bi_size);
 	if (unlikely(!clone)) {
@@ -2062,7 +2039,11 @@
 	io->ctx.bio_out = clone;
 	io->ctx.iter_out = clone->bi_iter;
 
-	sector += bio_sectors(clone);
+	if (crypt_integrity_aead(cc)) {
+		bio_copy_data(clone, io->base_bio);
+		io->ctx.bio_in = clone;
+		io->ctx.iter_in = clone->bi_iter;
+	}
 
 	crypt_inc_pending(io);
 	r = crypt_convert(cc, ctx,
@@ -2087,10 +2068,8 @@
 	}
 
 	/* Encryption was already finished, submit io now */
-	if (crypt_finished) {
+	if (crypt_finished)
 		kcryptd_crypt_write_io_submit(io, 0);
-		io->sector = sector;
-	}
 
 dec:
 	crypt_dec_pending(io);
@@ -2211,11 +2190,6 @@
 		kcryptd_crypt_write_convert(io);
 }
 
-static void kcryptd_crypt_tasklet(unsigned long work)
-{
-	kcryptd_crypt((struct work_struct *)work);
-}
-
 static void kcryptd_queue_crypt(struct dm_crypt_io *io)
 {
 	struct crypt_config *cc = io->cc;
@@ -2227,14 +2201,10 @@
 		 * irqs_disabled(): the kernel may run some IO completion from the idle thread, but
 		 * it is being executed with irqs disabled.
 		 */
-		if (in_hardirq() || irqs_disabled()) {
-			tasklet_init(&io->tasklet, kcryptd_crypt_tasklet, (unsigned long)&io->work);
-			tasklet_schedule(&io->tasklet);
+		if (!(in_hardirq() || irqs_disabled())) {
+			kcryptd_crypt(&io->work);
 			return;
 		}
-
-		kcryptd_crypt(&io->work);
-		return;
 	}
 
 	INIT_WORK(&io->work, kcryptd_crypt);
@@ -2579,7 +2549,7 @@
 
 static int get_key_size(char **key_string)
 {
-	return (*key_string[0] == ':') ? -EINVAL : strlen(*key_string) >> 1;
+	return (*key_string[0] == ':') ? -EINVAL : (int)(strlen(*key_string) >> 1);
 }
 
 #endif /* CONFIG_KEYS */
@@ -3435,6 +3405,11 @@
 	return DM_MAPIO_SUBMITTED;
 }
 
+static char hex2asc(unsigned char c)
+{
+	return c + '0' + ((unsigned)(9 - c) >> 4 & 0x27);
+}
+
 static void crypt_status(struct dm_target *ti, status_type_t type,
 			 unsigned status_flags, char *result, unsigned maxlen)
 {
@@ -3453,9 +3428,12 @@
 		if (cc->key_size > 0) {
 			if (cc->key_string)
 				DMEMIT(":%u:%s", cc->key_size, cc->key_string);
-			else
-				for (i = 0; i < cc->key_size; i++)
-					DMEMIT("%02x", cc->key[i]);
+			else {
+				for (i = 0; i < cc->key_size; i++) {
+					DMEMIT("%c%c", hex2asc(cc->key[i] >> 4),
+					       hex2asc(cc->key[i] & 0xf));
+				}
+			}
 		} else
 			DMEMIT("-");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-delay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-delay.c
@@ -30,7 +30,7 @@
 	struct workqueue_struct *kdelayd_wq;
 	struct work_struct flush_expired_bios;
 	struct list_head delayed_bios;
-	atomic_t may_delay;
+	bool may_delay;
 
 	struct delay_class read;
 	struct delay_class write;
@@ -191,7 +191,7 @@
 	INIT_WORK(&dc->flush_expired_bios, flush_expired_bios);
 	INIT_LIST_HEAD(&dc->delayed_bios);
 	mutex_init(&dc->timer_lock);
-	atomic_set(&dc->may_delay, 1);
+	dc->may_delay = true;
 	dc->argc = argc;
 
 	ret = delay_class_ctr(ti, &dc->read, argv);
@@ -245,7 +245,7 @@
 	struct dm_delay_info *delayed;
 	unsigned long expires = 0;
 
-	if (!c->delay || !atomic_read(&dc->may_delay))
+	if (!c->delay)
 		return DM_MAPIO_REMAPPED;
 
 	delayed = dm_per_bio_data(bio, sizeof(struct dm_delay_info));
@@ -254,6 +254,10 @@
 	delayed->expires = expires = jiffies + msecs_to_jiffies(c->delay);
 
 	mutex_lock(&delayed_bios_lock);
+	if (unlikely(!dc->may_delay)) {
+		mutex_unlock(&delayed_bios_lock);
+		return DM_MAPIO_REMAPPED;
+	}
 	c->ops++;
 	list_add_tail(&delayed->list, &dc->delayed_bios);
 	mutex_unlock(&delayed_bios_lock);
@@ -267,7 +271,10 @@
 {
 	struct delay_c *dc = ti->private;
 
-	atomic_set(&dc->may_delay, 0);
+	mutex_lock(&delayed_bios_lock);
+	dc->may_delay = false;
+	mutex_unlock(&delayed_bios_lock);
+
 	del_timer_sync(&dc->delay_timer);
 	flush_bios(flush_delayed_bios(dc, 1));
 }
@@ -276,7 +283,7 @@
 {
 	struct delay_c *dc = ti->private;
 
-	atomic_set(&dc->may_delay, 1);
+	dc->may_delay = true;
 }
 
 static int delay_map(struct dm_target *ti, struct bio *bio)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-ebs-target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-ebs-target.c
@@ -440,7 +440,7 @@
 static struct target_type ebs_target = {
 	.name		 = "ebs",
 	.version	 = {1, 0, 1},
-	.features	 = DM_TARGET_PASSES_INTEGRITY,
+	.features	 = 0,
 	.module		 = THIS_MODULE,
 	.ctr		 = ebs_ctr,
 	.dtr		 = ebs_dtr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-era-target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-era-target.c
@@ -1400,7 +1400,7 @@
 static void stop_worker(struct era *era)
 {
 	atomic_set(&era->suspended, 1);
-	flush_workqueue(era->wq);
+	drain_workqueue(era->wq);
 }
 
 /*----------------------------------------------------------------
@@ -1570,6 +1570,12 @@
 	}
 
 	stop_worker(era);
+
+	r = metadata_commit(era->md);
+	if (r) {
+		DMERR("%s: metadata_commit failed", __func__);
+		/* FIXME: fail mode */
+	}
 }
 
 static int era_preresume(struct dm_target *ti)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-flakey.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-flakey.c
@@ -124,9 +124,9 @@
 			 * Direction r or w?
 			 */
 			arg_name = dm_shift_arg(as);
-			if (!strcasecmp(arg_name, "w"))
+			if (arg_name && !strcasecmp(arg_name, "w"))
 				fc->corrupt_bio_rw = WRITE;
-			else if (!strcasecmp(arg_name, "r"))
+			else if (arg_name && !strcasecmp(arg_name, "r"))
 				fc->corrupt_bio_rw = READ;
 			else {
 				ti->error = "Invalid corrupt bio direction (r or w)";
@@ -301,9 +301,13 @@
 	 */
 	bio_for_each_segment(bvec, bio, iter) {
 		if (bio_iter_len(bio, iter) > corrupt_bio_byte) {
-			char *segment = (page_address(bio_iter_page(bio, iter))
-					 + bio_iter_offset(bio, iter));
+			char *segment;
+			struct page *page = bio_iter_page(bio, iter);
+			if (unlikely(page == ZERO_PAGE(0)))
+				break;
+			segment = bvec_kmap_local(&bvec);
 			segment[corrupt_bio_byte] = fc->corrupt_bio_value;
+			kunmap_local(segment);
 			DMDEBUG("Corrupting data bio=%p by writing %u to byte %u "
 				"(rw=%c bi_opf=%u bi_sector=%llu size=%u)\n",
 				bio, fc->corrupt_bio_value, fc->corrupt_bio_byte,
@@ -359,9 +363,11 @@
 		/*
 		 * Corrupt matching writes.
 		 */
-		if (fc->corrupt_bio_byte && (fc->corrupt_bio_rw == WRITE)) {
-			if (all_corrupt_bio_flags_match(bio, fc))
-				corrupt_bio_data(bio, fc);
+		if (fc->corrupt_bio_byte) {
+			if (fc->corrupt_bio_rw == WRITE) {
+				if (all_corrupt_bio_flags_match(bio, fc))
+					corrupt_bio_data(bio, fc);
+			}
 			goto map_bio;
 		}
 
@@ -387,13 +393,14 @@
 		return DM_ENDIO_DONE;
 
 	if (!*error && pb->bio_submitted && (bio_data_dir(bio) == READ)) {
-		if (fc->corrupt_bio_byte && (fc->corrupt_bio_rw == READ) &&
-		    all_corrupt_bio_flags_match(bio, fc)) {
-			/*
-			 * Corrupt successful matching READs while in down state.
-			 */
-			corrupt_bio_data(bio, fc);
-
+		if (fc->corrupt_bio_byte) {
+			if ((fc->corrupt_bio_rw == READ) &&
+			    all_corrupt_bio_flags_match(bio, fc)) {
+				/*
+				 * Corrupt successful matching READs while in down state.
+				 */
+				corrupt_bio_data(bio, fc);
+			}
 		} else if (!test_bit(DROP_WRITES, &fc->flags) &&
 			   !test_bit(ERROR_WRITES, &fc->flags)) {
 			/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-init.c
@@ -8,6 +8,7 @@
  */
 
 #include <linux/ctype.h>
+#include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/device-mapper.h>
 #include <linux/init.h>
@@ -18,12 +19,17 @@
 #define DM_MAX_DEVICES 256
 #define DM_MAX_TARGETS 256
 #define DM_MAX_STR_SIZE 4096
+#define DM_MAX_WAITFOR 256
 
 static char *create;
 
+static char *waitfor[DM_MAX_WAITFOR];
+
 /*
  * Format: dm-mod.create=<name>,<uuid>,<minor>,<flags>,<table>[,<table>+][;<name>,<uuid>,<minor>,<flags>,<table>[,<table>+]+]
  * Table format: <start_sector> <num_sectors> <target_type> <target_args>
+ * Block devices to wait for to become available before setting up tables:
+ * dm-mod.waitfor=<device1>[,..,<deviceN>]
  *
  * See Documentation/admin-guide/device-mapper/dm-init.rst for dm-mod.create="..." format
  * details.
@@ -207,8 +213,10 @@
 	strscpy(dev->dmi.uuid, field[1], sizeof(dev->dmi.uuid));
 	/* minor */
 	if (strlen(field[2])) {
-		if (kstrtoull(field[2], 0, &dev->dmi.dev))
+		if (kstrtoull(field[2], 0, &dev->dmi.dev) ||
+		    dev->dmi.dev >= (1 << MINORBITS))
 			return ERR_PTR(-EINVAL);
+		dev->dmi.dev = huge_encode_dev((dev_t)dev->dmi.dev);
 		dev->dmi.flags |= DM_PERSISTENT_DEV_FLAG;
 	}
 	/* flags */
@@ -266,7 +274,7 @@
 	struct dm_device *dev;
 	LIST_HEAD(devices);
 	char *str;
-	int r;
+	int i, r;
 
 	if (!create)
 		return 0;
@@ -286,6 +294,17 @@
 	DMINFO("waiting for all devices to be available before creating mapped devices");
 	wait_for_device_probe();
 
+	for (i = 0; i < ARRAY_SIZE(waitfor); i++) {
+		if (waitfor[i]) {
+			DMINFO("waiting for device %s ...", waitfor[i]);
+			while (!dm_get_dev_t(waitfor[i]))
+				msleep(5);
+		}
+	}
+
+	if (waitfor[0])
+		DMINFO("all devices available");
+
 	list_for_each_entry(dev, &devices, list) {
 		if (dm_early_create(&dev->dmi, dev->table,
 				    dev->target_args_array))
@@ -301,3 +320,6 @@
 
 module_param(create, charp, 0);
 MODULE_PARM_DESC(create, "Create a mapped device in early boot");
+
+module_param_array(waitfor, charp, NULL, 0);
+MODULE_PARM_DESC(waitfor, "Devices to wait for before setting up tables");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-integrity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-integrity.c
@@ -31,11 +31,11 @@
 #define DEFAULT_BUFFER_SECTORS		128
 #define DEFAULT_JOURNAL_WATERMARK	50
 #define DEFAULT_SYNC_MSEC		10000
-#define DEFAULT_MAX_JOURNAL_SECTORS	131072
+#define DEFAULT_MAX_JOURNAL_SECTORS	(IS_ENABLED(CONFIG_64BIT) ? 131072 : 8192)
 #define MIN_LOG2_INTERLEAVE_SECTORS	3
 #define MAX_LOG2_INTERLEAVE_SECTORS	31
 #define METADATA_WORKQUEUE_MAX_ACTIVE	16
-#define RECALC_SECTORS			32768
+#define RECALC_SECTORS			(IS_ENABLED(CONFIG_64BIT) ? 32768 : 2048)
 #define RECALC_WRITE_SUPER		16
 #define BITMAP_BLOCK_SIZE		4096	/* don't change it */
 #define BITMAP_FLUSH_INTERVAL		(10 * HZ)
@@ -259,6 +259,7 @@
 
 	struct completion crypto_backoff;
 
+	bool wrote_to_journal;
 	bool journal_uptodate;
 	bool just_formatted;
 	bool recalculate_flag;
@@ -1761,11 +1762,12 @@
 		sectors_to_process = dio->range.n_sectors;
 
 		__bio_for_each_segment(bv, bio, iter, dio->bio_details.bi_iter) {
+			struct bio_vec bv_copy = bv;
 			unsigned pos;
 			char *mem, *checksums_ptr;
 
 again:
-			mem = (char *)kmap_atomic(bv.bv_page) + bv.bv_offset;
+			mem = (char *)kmap_atomic(bv_copy.bv_page) + bv_copy.bv_offset;
 			pos = 0;
 			checksums_ptr = checksums;
 			do {
@@ -1774,7 +1776,7 @@
 				sectors_to_process -= ic->sectors_per_block;
 				pos += ic->sectors_per_block << SECTOR_SHIFT;
 				sector += ic->sectors_per_block;
-			} while (pos < bv.bv_len && sectors_to_process && checksums != checksums_onstack);
+			} while (pos < bv_copy.bv_len && sectors_to_process && checksums != checksums_onstack);
 			kunmap_atomic(mem);
 
 			r = dm_integrity_rw_tag(ic, checksums, &dio->metadata_block, &dio->metadata_offset,
@@ -1795,9 +1797,9 @@
 			if (!sectors_to_process)
 				break;
 
-			if (unlikely(pos < bv.bv_len)) {
-				bv.bv_offset += pos;
-				bv.bv_len -= pos;
+			if (unlikely(pos < bv_copy.bv_len)) {
+				bv_copy.bv_offset += pos;
+				bv_copy.bv_len -= pos;
 				goto again;
 			}
 		}
@@ -2361,6 +2363,8 @@
 	if (!commit_sections)
 		goto release_flush_bios;
 
+	ic->wrote_to_journal = true;
+
 	i = commit_start;
 	for (n = 0; n < commit_sections; n++) {
 		for (j = 0; j < ic->journal_section_entries; j++) {
@@ -2459,9 +2463,11 @@
 					dm_integrity_io_error(ic, "invalid sector in journal", -EIO);
 					sec &= ~(sector_t)(ic->sectors_per_block - 1);
 				}
+				if (unlikely(sec >= ic->provided_data_sectors)) {
+					journal_entry_set_unused(je);
+					continue;
+				}
 			}
-			if (unlikely(sec >= ic->provided_data_sectors))
-				continue;
 			get_area_and_offset(ic, sec, &area, &offset);
 			restore_last_bytes(ic, access_journal_data(ic, i, j), je);
 			for (k = j + 1; k < ic->journal_section_entries; k++) {
@@ -2573,10 +2579,6 @@
 
 	unsigned prev_free_sectors;
 
-	/* the following test is not needed, but it tests the replay code */
-	if (unlikely(dm_post_suspending(ic->ti)) && !ic->meta_dev)
-		return;
-
 	spin_lock_irq(&ic->endio_wait.lock);
 	write_start = ic->committed_section;
 	write_sections = ic->n_committed_sections;
@@ -3083,10 +3085,17 @@
 	drain_workqueue(ic->commit_wq);
 
 	if (ic->mode == 'J') {
-		if (ic->meta_dev)
-			queue_work(ic->writer_wq, &ic->writer_work);
+		queue_work(ic->writer_wq, &ic->writer_work);
 		drain_workqueue(ic->writer_wq);
 		dm_integrity_flush_buffers(ic, true);
+		if (ic->wrote_to_journal) {
+			init_journal(ic, ic->free_section,
+				     ic->journal_sections - ic->free_section, ic->commit_seq);
+			if (ic->free_section) {
+				init_journal(ic, 0, ic->free_section,
+					     next_commit_seq(ic->commit_seq));
+			}
+		}
 	}
 
 	if (ic->mode == 'B') {
@@ -3114,6 +3123,8 @@
 
 	DEBUG_print("resume\n");
 
+	ic->wrote_to_journal = false;
+
 	if (ic->provided_data_sectors != old_provided_data_sectors) {
 		if (ic->provided_data_sectors > old_provided_data_sectors &&
 		    ic->mode == 'B' &&
@@ -4072,7 +4083,7 @@
 		} else if (sscanf(opt_string, "sectors_per_bit:%llu%c", &llval, &dummy) == 1) {
 			log2_sectors_per_bitmap_bit = !llval ? 0 : __ilog2_u64(llval);
 		} else if (sscanf(opt_string, "bitmap_flush_interval:%u%c", &val, &dummy) == 1) {
-			if (val >= (uint64_t)UINT_MAX * 1000 / HZ) {
+			if ((uint64_t)val >= (uint64_t)UINT_MAX * 1000 / HZ) {
 				r = -EINVAL;
 				ti->error = "Invalid bitmap_flush_interval argument";
 				goto bad;
@@ -4381,6 +4392,7 @@
 	}
 
 	if (ic->internal_hash) {
+		size_t recalc_tags_size;
 		ic->recalc_wq = alloc_workqueue("dm-integrity-recalc", WQ_MEM_RECLAIM, 1);
 		if (!ic->recalc_wq ) {
 			ti->error = "Cannot allocate workqueue";
@@ -4394,8 +4406,10 @@
 			r = -ENOMEM;
 			goto bad;
 		}
-		ic->recalc_tags = kvmalloc_array(RECALC_SECTORS >> ic->sb->log2_sectors_per_block,
-						 ic->tag_size, GFP_KERNEL);
+		recalc_tags_size = (RECALC_SECTORS >> ic->sb->log2_sectors_per_block) * ic->tag_size;
+		if (crypto_shash_digestsize(ic->internal_hash) > ic->tag_size)
+			recalc_tags_size += crypto_shash_digestsize(ic->internal_hash) - ic->tag_size;
+		ic->recalc_tags = kvmalloc(recalc_tags_size, GFP_KERNEL);
 		if (!ic->recalc_tags) {
 			ti->error = "Cannot allocate tags for recalculating";
 			r = -ENOMEM;
@@ -4473,8 +4487,6 @@
 	}
 
 	if (should_write_sb) {
-		int r;
-
 		init_journal(ic, 0, ic->journal_sections, 0);
 		r = dm_integrity_failed(ic);
 		if (unlikely(r)) {
@@ -4528,6 +4540,8 @@
 	BUG_ON(!RB_EMPTY_ROOT(&ic->in_progress));
 	BUG_ON(!list_empty(&ic->wait_list));
 
+	if (ic->mode == 'B')
+		cancel_delayed_work_sync(&ic->bitmap_flush_work);
 	if (ic->metadata_wq)
 		destroy_workqueue(ic->metadata_wq);
 	if (ic->wait_wq)
@@ -4619,11 +4633,13 @@
 	}
 
 	r = dm_register_target(&integrity_target);
-
-	if (r < 0)
+	if (r < 0) {
 		DMERR("register failed %d", r);
+		kmem_cache_destroy(journal_io_cache);
+		return r;
+	}
 
-	return r;
+	return 0;
 }
 
 static void __exit dm_integrity_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-ioctl.c
@@ -18,6 +18,7 @@
 #include <linux/dm-ioctl.h>
 #include <linux/hdreg.h>
 #include <linux/compat.h>
+#include <linux/nospec.h>
 
 #include <linux/uaccess.h>
 #include <linux/ima.h>
@@ -481,7 +482,7 @@
 		dm_table_event(table);
 	dm_put_live_table(hc->md, srcu_idx);
 
-	if (!dm_kobject_uevent(hc->md, KOBJ_CHANGE, param->event_nr))
+	if (!dm_kobject_uevent(hc->md, KOBJ_CHANGE, param->event_nr, false))
 		param->flags |= DM_UEVENT_GENERATED_FLAG;
 
 	md = hc->md;
@@ -654,7 +655,7 @@
     size_t *needed = needed_param;
 
     *needed += sizeof(struct dm_target_versions);
-    *needed += strlen(tt->name);
+    *needed += strlen(tt->name) + 1;
     *needed += ALIGN_MASK;
 }
 
@@ -719,7 +720,7 @@
 	iter_info.old_vers = NULL;
 	iter_info.vers = vers;
 	iter_info.flags = 0;
-	iter_info.end = (char *)vers+len;
+	iter_info.end = (char *)vers + needed;
 
 	/*
 	 * Now loop through filling out the names & versions.
@@ -890,15 +891,21 @@
 	struct hash_cell *hc = NULL;
 
 	if (*param->uuid) {
-		if (*param->name || param->dev)
+		if (*param->name || param->dev) {
+			DMERR("Invalid ioctl structure: uuid %s, name %s, dev %llx",
+			      param->uuid, param->name, (unsigned long long)param->dev);
 			return NULL;
+		}
 
 		hc = __get_uuid_cell(param->uuid);
 		if (!hc)
 			return NULL;
 	} else if (*param->name) {
-		if (param->dev)
+		if (param->dev) {
+			DMERR("Invalid ioctl structure: name %s, dev %llx",
+			      param->name, (unsigned long long)param->dev);
 			return NULL;
+		}
 
 		hc = __get_name_cell(param->name);
 		if (!hc)
@@ -988,7 +995,7 @@
 
 	dm_ima_measure_on_device_remove(md, false);
 
-	if (!dm_kobject_uevent(md, KOBJ_REMOVE, param->event_nr))
+	if (!dm_kobject_uevent(md, KOBJ_REMOVE, param->event_nr, false))
 		param->flags |= DM_UEVENT_GENERATED_FLAG;
 
 	dm_put(md);
@@ -1122,6 +1129,7 @@
 	struct hash_cell *hc;
 	struct mapped_device *md;
 	struct dm_table *new_map, *old_map = NULL;
+	bool need_resize_uevent = false;
 
 	down_write(&_hash_lock);
 
@@ -1142,14 +1150,35 @@
 
 	/* Do we need to load a new map ? */
 	if (new_map) {
+		sector_t old_size, new_size;
+
 		/* Suspend if it isn't already suspended */
 		if (param->flags & DM_SKIP_LOCKFS_FLAG)
 			suspend_flags &= ~DM_SUSPEND_LOCKFS_FLAG;
 		if (param->flags & DM_NOFLUSH_FLAG)
 			suspend_flags |= DM_SUSPEND_NOFLUSH_FLAG;
-		if (!dm_suspended_md(md))
-			dm_suspend(md, suspend_flags);
+		if (!dm_suspended_md(md)) {
+			r = dm_suspend(md, suspend_flags);
+			if (r) {
+				down_write(&_hash_lock);
+				hc = dm_get_mdptr(md);
+				if (hc && !hc->new_map) {
+					hc->new_map = new_map;
+					new_map = NULL;
+				} else {
+					r = -ENXIO;
+				}
+				up_write(&_hash_lock);
+				if (new_map) {
+					dm_sync_table(md);
+					dm_table_destroy(new_map);
+				}
+				dm_put(md);
+				return r;
+			}
+		}
 
+		old_size = dm_get_size(md);
 		old_map = dm_swap_table(md, new_map);
 		if (IS_ERR(old_map)) {
 			dm_sync_table(md);
@@ -1157,6 +1186,9 @@
 			dm_put(md);
 			return PTR_ERR(old_map);
 		}
+		new_size = dm_get_size(md);
+		if (old_size && new_size && old_size != new_size)
+			need_resize_uevent = true;
 
 		if (dm_table_get_mode(new_map) & FMODE_WRITE)
 			set_disk_ro(dm_disk(md), 0);
@@ -1169,7 +1201,7 @@
 		if (!r) {
 			dm_ima_measure_on_device_resume(md, new_map ? true : false);
 
-			if (!dm_kobject_uevent(md, KOBJ_CHANGE, param->event_nr))
+			if (!dm_kobject_uevent(md, KOBJ_CHANGE, param->event_nr, need_resize_uevent))
 				param->flags |= DM_UEVENT_GENERATED_FLAG;
 		}
 	}
@@ -1525,11 +1557,12 @@
 		has_new_map = true;
 	}
 
-	param->flags &= ~DM_INACTIVE_PRESENT_FLAG;
-
-	__dev_status(hc->md, param);
 	md = hc->md;
 	up_write(&_hash_lock);
+
+	param->flags &= ~DM_INACTIVE_PRESENT_FLAG;
+	__dev_status(md, param);
+
 	if (old_map) {
 		dm_sync_table(md);
 		dm_table_destroy(old_map);
@@ -1788,6 +1821,7 @@
 	if (unlikely(cmd >= ARRAY_SIZE(_ioctls)))
 		return NULL;
 
+	cmd = array_index_nospec(cmd, ARRAY_SIZE(_ioctls));
 	*ioctl_flags = _ioctls[cmd].flags;
 	return _ioctls[cmd].fn;
 }
@@ -1849,8 +1883,12 @@
 	if (copy_from_user(param_kernel, user, minimum_data_size))
 		return -EFAULT;
 
-	if (param_kernel->data_size < minimum_data_size)
+	if (unlikely(param_kernel->data_size < minimum_data_size) ||
+	    unlikely(param_kernel->data_size > DM_MAX_TARGETS * DM_MAX_TARGET_PARAMS)) {
+		DMERR("Invalid data size in the ioctl structure: %u",
+		      param_kernel->data_size);
 		return -EINVAL;
+	}
 
 	secure_data = param_kernel->flags & DM_SECURE_DATA_FLAG;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-log.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-log.c
@@ -415,8 +415,7 @@
 	/*
 	 * Work out how many "unsigned long"s we need to hold the bitset.
 	 */
-	bitset_size = dm_round_up(region_count,
-				  sizeof(*lc->clean_bits) << BYTE_SHIFT);
+	bitset_size = dm_round_up(region_count, BITS_PER_LONG);
 	bitset_size >>= BYTE_SHIFT;
 
 	lc->bitset_uint32_count = bitset_size / sizeof(*lc->clean_bits);
@@ -616,7 +615,7 @@
 			log_clear_bit(lc, lc->clean_bits, i);
 
 	/* clear any old bits -- device has shrunk */
-	for (i = lc->region_count; i % (sizeof(*lc->clean_bits) << BYTE_SHIFT); i++)
+	for (i = lc->region_count; i % BITS_PER_LONG; i++)
 		log_clear_bit(lc, lc->clean_bits, i);
 
 	/* copy clean across to sync */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-ps-historical-service-time.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-ps-historical-service-time.c
@@ -432,7 +432,7 @@
 {
 	struct selector *s = ps->context;
 	struct path_info *pi = NULL, *best = NULL;
-	u64 time_now = sched_clock();
+	u64 time_now = ktime_get_ns();
 	struct dm_path *ret = NULL;
 	unsigned long flags;
 
@@ -473,7 +473,7 @@
 
 static u64 path_service_time(struct path_info *pi, u64 start_time)
 {
-	u64 sched_now = ktime_get_ns();
+	u64 now = ktime_get_ns();
 
 	/* if a previous disk request has finished after this IO was
 	 * sent to the hardware, pretend the submission happened
@@ -482,11 +482,11 @@
 	if (time_after64(pi->last_finish, start_time))
 		start_time = pi->last_finish;
 
-	pi->last_finish = sched_now;
-	if (time_before64(sched_now, start_time))
+	pi->last_finish = now;
+	if (time_before64(now, start_time))
 		return 0;
 
-	return sched_now - start_time;
+	return now - start_time;
 }
 
 static int hst_end_io(struct path_selector *ps, struct dm_path *path,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-raid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-raid.c
@@ -1001,12 +1001,13 @@
 static int validate_raid_redundancy(struct raid_set *rs)
 {
 	unsigned int i, rebuild_cnt = 0;
-	unsigned int rebuilds_per_group = 0, copies;
+	unsigned int rebuilds_per_group = 0, copies, raid_disks;
 	unsigned int group_size, last_group_start;
 
-	for (i = 0; i < rs->md.raid_disks; i++)
-		if (!test_bit(In_sync, &rs->dev[i].rdev.flags) ||
-		    !rs->dev[i].rdev.sb_page)
+	for (i = 0; i < rs->raid_disks; i++)
+		if (!test_bit(FirstUse, &rs->dev[i].rdev.flags) &&
+		    ((!test_bit(In_sync, &rs->dev[i].rdev.flags) ||
+		      !rs->dev[i].rdev.sb_page)))
 			rebuild_cnt++;
 
 	switch (rs->md.level) {
@@ -1046,8 +1047,9 @@
 		 *	    A	 A    B	   B	C
 		 *	    C	 D    D	   E	E
 		 */
+		raid_disks = min(rs->raid_disks, rs->md.raid_disks);
 		if (__is_raid10_near(rs->md.new_layout)) {
-			for (i = 0; i < rs->md.raid_disks; i++) {
+			for (i = 0; i < raid_disks; i++) {
 				if (!(i % copies))
 					rebuilds_per_group = 0;
 				if ((!rs->dev[i].rdev.sb_page ||
@@ -1070,10 +1072,10 @@
 		 * results in the need to treat the last (potentially larger)
 		 * set differently.
 		 */
-		group_size = (rs->md.raid_disks / copies);
-		last_group_start = (rs->md.raid_disks / group_size) - 1;
+		group_size = (raid_disks / copies);
+		last_group_start = (raid_disks / group_size) - 1;
 		last_group_start *= group_size;
-		for (i = 0; i < rs->md.raid_disks; i++) {
+		for (i = 0; i < raid_disks; i++) {
 			if (!(i % copies) && !(i > last_group_start))
 				rebuilds_per_group = 0;
 			if ((!rs->dev[i].rdev.sb_page ||
@@ -1588,7 +1590,7 @@
 {
 	int i;
 
-	for (i = 0; i < rs->md.raid_disks; i++) {
+	for (i = 0; i < rs->raid_disks; i++) {
 		struct md_rdev *rdev = &rs->dev[i].rdev;
 
 		if (!test_bit(Journal, &rdev->flags) &&
@@ -3256,8 +3258,7 @@
 	r = md_start(&rs->md);
 	if (r) {
 		ti->error = "Failed to start raid array";
-		mddev_unlock(&rs->md);
-		goto bad_md_start;
+		goto bad_unlock;
 	}
 
 	/* If raid4/5/6 journal mode explicitly requested (only possible with journal dev) -> set it */
@@ -3265,8 +3266,7 @@
 		r = r5c_journal_mode_set(&rs->md, rs->journal_dev.mode);
 		if (r) {
 			ti->error = "Failed to set raid4/5/6 journal mode";
-			mddev_unlock(&rs->md);
-			goto bad_journal_mode_set;
+			goto bad_unlock;
 		}
 	}
 
@@ -3277,14 +3277,14 @@
 	if (rs_is_raid456(rs)) {
 		r = rs_set_raid456_stripe_cache(rs);
 		if (r)
-			goto bad_stripe_cache;
+			goto bad_unlock;
 	}
 
 	/* Now do an early reshape check */
 	if (test_bit(RT_FLAG_RESHAPE_RS, &rs->runtime_flags)) {
 		r = rs_check_reshape(rs);
 		if (r)
-			goto bad_check_reshape;
+			goto bad_unlock;
 
 		/* Restore new, ctr requested layout to perform check */
 		rs_config_restore(rs, &rs_layout);
@@ -3293,7 +3293,7 @@
 			r = rs->md.pers->check_reshape(&rs->md);
 			if (r) {
 				ti->error = "Reshape check failed";
-				goto bad_check_reshape;
+				goto bad_unlock;
 			}
 		}
 	}
@@ -3304,11 +3304,9 @@
 	mddev_unlock(&rs->md);
 	return 0;
 
-bad_md_start:
-bad_journal_mode_set:
-bad_stripe_cache:
-bad_check_reshape:
+bad_unlock:
 	md_stop(&rs->md);
+	mddev_unlock(&rs->md);
 bad:
 	raid_set_free(rs);
 
@@ -3319,7 +3317,9 @@
 {
 	struct raid_set *rs = ti->private;
 
+	mddev_lock_nointr(&rs->md);
 	md_stop(&rs->md);
+	mddev_unlock(&rs->md);
 	raid_set_free(rs);
 }
 
@@ -3329,14 +3329,14 @@
 	struct mddev *mddev = &rs->md;
 
 	/*
-	 * If we're reshaping to add disk(s)), ti->len and
+	 * If we're reshaping to add disk(s), ti->len and
 	 * mddev->array_sectors will differ during the process
 	 * (ti->len > mddev->array_sectors), so we have to requeue
 	 * bios with addresses > mddev->array_sectors here or
 	 * there will occur accesses past EOD of the component
 	 * data images thus erroring the raid set.
 	 */
-	if (unlikely(bio_end_sector(bio) > mddev->array_sectors))
+	if (unlikely(bio_has_data(bio) && bio_end_sector(bio) > mddev->array_sectors))
 		return DM_MAPIO_REQUEUE;
 
 	md_handle_request(mddev, bio);
@@ -3512,7 +3512,7 @@
 {
 	struct raid_set *rs = ti->private;
 	struct mddev *mddev = &rs->md;
-	struct r5conf *conf = mddev->private;
+	struct r5conf *conf = rs_is_raid456(rs) ? mddev->private : NULL;
 	int i, max_nr_stripes = conf ? conf->max_nr_stripes : 0;
 	unsigned long recovery;
 	unsigned int raid_param_cnt = 1; /* at least 1 for chunksize */
@@ -3771,13 +3771,13 @@
 	unsigned int i;
 	int r = 0;
 
-	for (i = 0; !r && i < rs->md.raid_disks; i++)
-		if (rs->dev[i].data_dev)
-			r = fn(ti,
-				 rs->dev[i].data_dev,
-				 0, /* No offset on data devs */
-				 rs->md.dev_sectors,
-				 data);
+	for (i = 0; !r && i < rs->raid_disks; i++) {
+		if (rs->dev[i].data_dev) {
+			r = fn(ti, rs->dev[i].data_dev,
+			       0, /* No offset on data devs */
+			       rs->md.dev_sectors, data);
+		}
+	}
 
 	return r;
 }
@@ -3822,7 +3822,7 @@
 
 	memset(cleared_failed_devices, 0, sizeof(cleared_failed_devices));
 
-	for (i = 0; i < mddev->raid_disks; i++) {
+	for (i = 0; i < rs->raid_disks; i++) {
 		r = &rs->dev[i].rdev;
 		/* HM FIXME: enhance journal device recovery processing */
 		if (test_bit(Journal, &r->flags))
@@ -4049,7 +4049,9 @@
 		 * Take this opportunity to check whether any failed
 		 * devices are reachable again.
 		 */
+		mddev_lock_nointr(mddev);
 		attempt_restore_of_faulty_devices(rs);
+		mddev_unlock(mddev);
 	}
 
 	if (test_and_clear_bit(RT_FLAG_RS_SUSPENDED, &rs->runtime_flags)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-rq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-rq.c
@@ -500,8 +500,15 @@
 
 	if (unlikely(!ti)) {
 		int srcu_idx;
-		struct dm_table *map = dm_get_live_table(md, &srcu_idx);
+		struct dm_table *map;
 
+		map = dm_get_live_table(md, &srcu_idx);
+		if (unlikely(!map)) {
+			DMERR_LIMIT("%s: mapping table unavailable, erroring io",
+				    dm_device_name(md));
+			dm_put_live_table(md, srcu_idx);
+			return BLK_STS_IOERR;
+		}
 		ti = dm_table_find_target(map, 0);
 		dm_put_live_table(md, srcu_idx);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-snap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-snap.c
@@ -686,8 +686,10 @@
 	for (i = 0; i < size; i++) {
 		slot = et->table + i;
 
-		hlist_bl_for_each_entry_safe(ex, pos, n, slot, hash_list)
+		hlist_bl_for_each_entry_safe(ex, pos, n, slot, hash_list) {
 			kmem_cache_free(mem, ex);
+			cond_resched();
+		}
 	}
 
 	kvfree(et->table);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-stats.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-stats.c
@@ -188,19 +188,25 @@
 	       atomic_read(&shared->in_flight[WRITE]);
 }
 
-void dm_stats_init(struct dm_stats *stats)
+int dm_stats_init(struct dm_stats *stats)
 {
 	int cpu;
 	struct dm_stats_last_position *last;
 
 	mutex_init(&stats->mutex);
 	INIT_LIST_HEAD(&stats->list);
+	stats->precise_timestamps = false;
 	stats->last = alloc_percpu(struct dm_stats_last_position);
+	if (!stats->last)
+		return -ENOMEM;
+
 	for_each_possible_cpu(cpu) {
 		last = per_cpu_ptr(stats->last, cpu);
 		last->last_sector = (sector_t)ULLONG_MAX;
 		last->last_rw = UINT_MAX;
 	}
+
+	return 0;
 }
 
 void dm_stats_cleanup(struct dm_stats *stats)
@@ -224,6 +230,7 @@
 				       atomic_read(&shared->in_flight[READ]),
 				       atomic_read(&shared->in_flight[WRITE]));
 			}
+			cond_resched();
 		}
 		dm_stat_free(&s->rcu_head);
 	}
@@ -231,6 +238,22 @@
 	mutex_destroy(&stats->mutex);
 }
 
+static void dm_stats_recalc_precise_timestamps(struct dm_stats *stats)
+{
+	struct list_head *l;
+	struct dm_stat *tmp_s;
+	bool precise_timestamps = false;
+
+	list_for_each(l, &stats->list) {
+		tmp_s = container_of(l, struct dm_stat, list_entry);
+		if (tmp_s->stat_flags & STAT_PRECISE_TIMESTAMPS) {
+			precise_timestamps = true;
+			break;
+		}
+	}
+	stats->precise_timestamps = precise_timestamps;
+}
+
 static int dm_stats_create(struct dm_stats *stats, sector_t start, sector_t end,
 			   sector_t step, unsigned stat_flags,
 			   unsigned n_histogram_entries,
@@ -313,6 +336,7 @@
 	for (ni = 0; ni < n_entries; ni++) {
 		atomic_set(&s->stat_shared[ni].in_flight[READ], 0);
 		atomic_set(&s->stat_shared[ni].in_flight[WRITE], 0);
+		cond_resched();
 	}
 
 	if (s->n_histogram_entries) {
@@ -325,6 +349,7 @@
 		for (ni = 0; ni < n_entries; ni++) {
 			s->stat_shared[ni].tmp.histogram = hi;
 			hi += s->n_histogram_entries + 1;
+			cond_resched();
 		}
 	}
 
@@ -345,6 +370,7 @@
 			for (ni = 0; ni < n_entries; ni++) {
 				p[ni].histogram = hi;
 				hi += s->n_histogram_entries + 1;
+				cond_resched();
 			}
 		}
 	}
@@ -376,6 +402,9 @@
 	}
 	ret_id = s->id;
 	list_add_tail_rcu(&s->list_entry, l);
+
+	dm_stats_recalc_precise_timestamps(stats);
+
 	mutex_unlock(&stats->mutex);
 
 	resume_callback(md);
@@ -418,6 +447,9 @@
 	}
 
 	list_del_rcu(&s->list_entry);
+
+	dm_stats_recalc_precise_timestamps(stats);
+
 	mutex_unlock(&stats->mutex);
 
 	/*
@@ -474,6 +506,7 @@
 			}
 			DMEMIT("\n");
 		}
+		cond_resched();
 	}
 	mutex_unlock(&stats->mutex);
 
@@ -621,13 +654,14 @@
 
 void dm_stats_account_io(struct dm_stats *stats, unsigned long bi_rw,
 			 sector_t bi_sector, unsigned bi_sectors, bool end,
-			 unsigned long duration_jiffies,
+			 unsigned long start_time,
 			 struct dm_stats_aux *stats_aux)
 {
 	struct dm_stat *s;
 	sector_t end_sector;
 	struct dm_stats_last_position *last;
 	bool got_precise_time;
+	unsigned long duration_jiffies = 0;
 
 	if (unlikely(!bi_sectors))
 		return;
@@ -647,16 +681,16 @@
 				       ));
 		WRITE_ONCE(last->last_sector, end_sector);
 		WRITE_ONCE(last->last_rw, bi_rw);
-	}
+	} else
+		duration_jiffies = jiffies - start_time;
 
 	rcu_read_lock();
 
 	got_precise_time = false;
 	list_for_each_entry_rcu(s, &stats->list, list_entry) {
 		if (s->stat_flags & STAT_PRECISE_TIMESTAMPS && !got_precise_time) {
-			if (!end)
-				stats_aux->duration_ns = ktime_to_ns(ktime_get());
-			else
+			/* start (!end) duration_ns is set by DM core's alloc_io() */
+			if (end)
 				stats_aux->duration_ns = ktime_to_ns(ktime_get()) - stats_aux->duration_ns;
 			got_precise_time = true;
 		}
@@ -750,6 +784,7 @@
 				local_irq_enable();
 			}
 		}
+		cond_resched();
 	}
 }
 
@@ -865,6 +900,8 @@
 
 		if (unlikely(sz + 1 >= maxlen))
 			goto buffer_overflow;
+
+		cond_resched();
 	}
 
 	if (clear)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-stats.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-stats.h
@@ -13,8 +13,7 @@
 	struct mutex mutex;
 	struct list_head list;	/* list of struct dm_stat */
 	struct dm_stats_last_position __percpu *last;
-	sector_t last_sector;
-	unsigned last_rw;
+	bool precise_timestamps;
 };
 
 struct dm_stats_aux {
@@ -22,7 +21,7 @@
 	unsigned long long duration_ns;
 };
 
-void dm_stats_init(struct dm_stats *st);
+int dm_stats_init(struct dm_stats *st);
 void dm_stats_cleanup(struct dm_stats *st);
 
 struct mapped_device;
@@ -32,7 +31,7 @@
 
 void dm_stats_account_io(struct dm_stats *stats, unsigned long bi_rw,
 			 sector_t bi_sector, unsigned bi_sectors, bool end,
-			 unsigned long duration_jiffies,
+			 unsigned long start_time,
 			 struct dm_stats_aux *aux);
 
 static inline bool dm_stats_used(struct dm_stats *st)
@@ -40,4 +39,10 @@
 	return !list_empty(&st->list);
 }
 
+static inline void dm_stats_record_start(struct dm_stats *stats, struct dm_stats_aux *aux)
+{
+	if (unlikely(stats->precise_timestamps))
+		aux->duration_ns = ktime_to_ns(ktime_get());
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-table.c
@@ -126,7 +126,12 @@
 int dm_table_create(struct dm_table **result, fmode_t mode,
 		    unsigned num_targets, struct mapped_device *md)
 {
-	struct dm_table *t = kzalloc(sizeof(*t), GFP_KERNEL);
+	struct dm_table *t;
+
+	if (num_targets > DM_MAX_TARGETS)
+		return -EOVERFLOW;
+
+	t = kzalloc(sizeof(*t), GFP_KERNEL);
 
 	if (!t)
 		return -ENOMEM;
@@ -140,7 +145,7 @@
 
 	if (!num_targets) {
 		kfree(t);
-		return -ENOMEM;
+		return -EOVERFLOW;
 	}
 
 	if (alloc_targets(t, num_targets)) {
@@ -1191,21 +1196,12 @@
 	struct mapped_device *md;
 };
 
-struct dm_keyslot_evict_args {
-	const struct blk_crypto_key *key;
-	int err;
-};
-
 static int dm_keyslot_evict_callback(struct dm_target *ti, struct dm_dev *dev,
 				     sector_t start, sector_t len, void *data)
 {
-	struct dm_keyslot_evict_args *args = data;
-	int err;
+	const struct blk_crypto_key *key = data;
 
-	err = blk_crypto_evict_key(bdev_get_queue(dev->bdev), args->key);
-	if (!args->err)
-		args->err = err;
-	/* Always try to evict the key from all devices. */
+	blk_crypto_evict_key(bdev_get_queue(dev->bdev), key);
 	return 0;
 }
 
@@ -1220,7 +1216,6 @@
 						       struct dm_keyslot_manager,
 						       ksm);
 	struct mapped_device *md = dksm->md;
-	struct dm_keyslot_evict_args args = { key };
 	struct dm_table *t;
 	int srcu_idx;
 	int i;
@@ -1233,10 +1228,11 @@
 		ti = dm_table_get_target(t, i);
 		if (!ti->type->iterate_devices)
 			continue;
-		ti->type->iterate_devices(ti, dm_keyslot_evict_callback, &args);
+		ti->type->iterate_devices(ti, dm_keyslot_evict_callback,
+					  (void *)key);
 	}
 	dm_put_live_table(md, srcu_idx);
-	return args.err;
+	return 0;
 }
 
 static const struct blk_ksm_ll_ops dm_ksm_ll_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-thin-metadata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-thin-metadata.c
@@ -724,6 +724,15 @@
 		goto bad_cleanup_data_sm;
 	}
 
+	/*
+	 * For pool metadata opening process, root setting is redundant
+	 * because it will be set again in __begin_transaction(). But dm
+	 * pool aborting process really needs to get last transaction's
+	 * root to avoid accessing broken btree.
+	 */
+	pmd->root = le64_to_cpu(disk_super->data_mapping_root);
+	pmd->details_root = le64_to_cpu(disk_super->device_details_root);
+
 	__setup_btree_details(pmd);
 	dm_bm_unlock(sblock);
 
@@ -776,13 +785,15 @@
 	return r;
 }
 
-static void __destroy_persistent_data_objects(struct dm_pool_metadata *pmd)
+static void __destroy_persistent_data_objects(struct dm_pool_metadata *pmd,
+					      bool destroy_bm)
 {
 	dm_sm_destroy(pmd->data_sm);
 	dm_sm_destroy(pmd->metadata_sm);
 	dm_tm_destroy(pmd->nb_tm);
 	dm_tm_destroy(pmd->tm);
-	dm_block_manager_destroy(pmd->bm);
+	if (destroy_bm)
+		dm_block_manager_destroy(pmd->bm);
 }
 
 static int __begin_transaction(struct dm_pool_metadata *pmd)
@@ -989,7 +1000,7 @@
 	}
 	pmd_write_unlock(pmd);
 	if (!pmd->fail_io)
-		__destroy_persistent_data_objects(pmd);
+		__destroy_persistent_data_objects(pmd, true);
 
 	kfree(pmd);
 	return 0;
@@ -1767,13 +1778,15 @@
 
 int dm_pool_block_is_shared(struct dm_pool_metadata *pmd, dm_block_t b, bool *result)
 {
-	int r;
+	int r = -EINVAL;
 	uint32_t ref_count;
 
 	down_read(&pmd->root_lock);
-	r = dm_sm_get_count(pmd->data_sm, b, &ref_count);
-	if (!r)
-		*result = (ref_count > 1);
+	if (!pmd->fail_io) {
+		r = dm_sm_get_count(pmd->data_sm, b, &ref_count);
+		if (!r)
+			*result = (ref_count > 1);
+	}
 	up_read(&pmd->root_lock);
 
 	return r;
@@ -1781,10 +1794,11 @@
 
 int dm_pool_inc_data_range(struct dm_pool_metadata *pmd, dm_block_t b, dm_block_t e)
 {
-	int r = 0;
+	int r = -EINVAL;
 
 	pmd_write_lock(pmd);
-	r = dm_sm_inc_blocks(pmd->data_sm, b, e);
+	if (!pmd->fail_io)
+		r = dm_sm_inc_blocks(pmd->data_sm, b, e);
 	pmd_write_unlock(pmd);
 
 	return r;
@@ -1792,10 +1806,11 @@
 
 int dm_pool_dec_data_range(struct dm_pool_metadata *pmd, dm_block_t b, dm_block_t e)
 {
-	int r = 0;
+	int r = -EINVAL;
 
 	pmd_write_lock(pmd);
-	r = dm_sm_dec_blocks(pmd->data_sm, b, e);
+	if (!pmd->fail_io)
+		r = dm_sm_dec_blocks(pmd->data_sm, b, e);
 	pmd_write_unlock(pmd);
 
 	return r;
@@ -1888,19 +1903,52 @@
 int dm_pool_abort_metadata(struct dm_pool_metadata *pmd)
 {
 	int r = -EINVAL;
+	struct dm_block_manager *old_bm = NULL, *new_bm = NULL;
+
+	/* fail_io is double-checked with pmd->root_lock held below */
+	if (unlikely(pmd->fail_io))
+		return r;
+
+	/*
+	 * Replacement block manager (new_bm) is created and old_bm destroyed outside of
+	 * pmd root_lock to avoid ABBA deadlock that would result (due to life-cycle of
+	 * shrinker associated with the block manager's bufio client vs pmd root_lock).
+	 * - must take shrinker_rwsem without holding pmd->root_lock
+	 */
+	new_bm = dm_block_manager_create(pmd->bdev, THIN_METADATA_BLOCK_SIZE << SECTOR_SHIFT,
+					 THIN_MAX_CONCURRENT_LOCKS);
 
 	pmd_write_lock(pmd);
-	if (pmd->fail_io)
+	if (pmd->fail_io) {
+		pmd_write_unlock(pmd);
 		goto out;
+	}
 
 	__set_abort_with_changes_flags(pmd);
-	__destroy_persistent_data_objects(pmd);
-	r = __create_persistent_data_objects(pmd, false);
+	__destroy_persistent_data_objects(pmd, false);
+	old_bm = pmd->bm;
+	if (IS_ERR(new_bm)) {
+		DMERR("could not create block manager during abort");
+		pmd->bm = NULL;
+		r = PTR_ERR(new_bm);
+		goto out_unlock;
+	}
+
+	pmd->bm = new_bm;
+	r = __open_or_format_metadata(pmd, false);
+	if (r) {
+		pmd->bm = NULL;
+		goto out_unlock;
+	}
+	new_bm = NULL;
+out_unlock:
 	if (r)
 		pmd->fail_io = true;
-
-out:
 	pmd_write_unlock(pmd);
+	dm_block_manager_destroy(old_bm);
+out:
+	if (new_bm && !IS_ERR(new_bm))
+		dm_block_manager_destroy(new_bm);
 
 	return r;
 }
@@ -2073,10 +2121,13 @@
 					dm_sm_threshold_fn fn,
 					void *context)
 {
-	int r;
+	int r = -EINVAL;
 
 	pmd_write_lock_in_core(pmd);
-	r = dm_sm_register_threshold_callback(pmd->metadata_sm, threshold, fn, context);
+	if (!pmd->fail_io) {
+		r = dm_sm_register_threshold_callback(pmd->metadata_sm,
+						      threshold, fn, context);
+	}
 	pmd_write_unlock(pmd);
 
 	return r;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-thin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-thin.c
@@ -2217,6 +2217,7 @@
 			throttle_work_update(&pool->throttle);
 			dm_pool_issue_prefetches(pool->pmd);
 		}
+		cond_resched();
 	}
 	blk_finish_plug(&plug);
 }
@@ -2299,6 +2300,7 @@
 			else
 				pool->process_cell(tc, cell);
 		}
+		cond_resched();
 	} while (!list_empty(&cells));
 }
 
@@ -2315,10 +2317,9 @@
 	struct thin_c *tc = NULL;
 
 	rcu_read_lock();
-	if (!list_empty(&pool->active_thins)) {
-		tc = list_entry_rcu(pool->active_thins.next, struct thin_c, list);
+	tc = list_first_or_null_rcu(&pool->active_thins, struct thin_c, list);
+	if (tc)
 		thin_get(tc);
-	}
 	rcu_read_unlock();
 
 	return tc;
@@ -2466,6 +2467,7 @@
 	init_completion(&pw->complete);
 	queue_work(pool->wq, &pw->worker);
 	wait_for_completion(&pw->complete);
+	destroy_work_on_stack(&pw->worker);
 }
 
 /*----------------------------------------------------------------*/
@@ -2907,6 +2909,8 @@
 	dm_bio_prison_destroy(pool->prison);
 	dm_kcopyd_client_destroy(pool->copier);
 
+	cancel_delayed_work_sync(&pool->waker);
+	cancel_delayed_work_sync(&pool->no_space_timeout);
 	if (pool->wq)
 		destroy_workqueue(pool->wq);
 
@@ -3379,6 +3383,7 @@
 	pt->low_water_blocks = low_water_blocks;
 	pt->adjusted_pf = pt->requested_pf = pf;
 	ti->num_flush_bios = 1;
+	ti->limit_swap_bios = true;
 
 	/*
 	 * Only need to enable discards if the pool should pass
@@ -3401,8 +3406,10 @@
 						calc_metadata_threshold(pt),
 						metadata_low_callback,
 						pool);
-	if (r)
+	if (r) {
+		ti->error = "Error registering metadata threshold";
 		goto out_flags_changed;
+	}
 
 	dm_pool_register_pre_commit_callback(pool->pmd,
 					     metadata_pre_commit_callback, pool);
@@ -3564,20 +3571,28 @@
 	 */
 	r = bind_control_target(pool, ti);
 	if (r)
-		return r;
+		goto out;
 
 	r = maybe_resize_data_dev(ti, &need_commit1);
 	if (r)
-		return r;
+		goto out;
 
 	r = maybe_resize_metadata_dev(ti, &need_commit2);
 	if (r)
-		return r;
+		goto out;
 
 	if (need_commit1 || need_commit2)
 		(void) commit(pool);
+out:
+	/*
+	 * When a thin-pool is PM_FAIL, it cannot be rebuilt if
+	 * bio is in deferred list. Therefore need to return 0
+	 * to allow pool_resume() to flush IO.
+	 */
+	if (r && get_pool_mode(pool) == PM_FAIL)
+		r = 0;
 
-	return 0;
+	return r;
 }
 
 static void pool_suspend_active_thins(struct pool *pool)
@@ -4249,6 +4264,7 @@
 		goto bad;
 
 	ti->num_flush_bios = 1;
+	ti->limit_swap_bios = true;
 	ti->flush_supported = true;
 	ti->per_io_data_size = sizeof(struct dm_thin_endio_hook);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-unstripe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-unstripe.c
@@ -84,8 +84,8 @@
 	}
 	uc->physical_start = start;
 
-	uc->unstripe_offset = uc->unstripe * uc->chunk_size;
-	uc->unstripe_width = (uc->stripes - 1) * uc->chunk_size;
+	uc->unstripe_offset = (sector_t)uc->unstripe * uc->chunk_size;
+	uc->unstripe_width = (sector_t)(uc->stripes - 1) * uc->chunk_size;
 	uc->chunk_shift = is_power_of_2(uc->chunk_size) ? fls(uc->chunk_size) - 1 : 0;
 
 	tmp_len = ti->len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-verity-fec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-verity-fec.c
@@ -24,7 +24,8 @@
  */
 static inline struct dm_verity_fec_io *fec_io(struct dm_verity_io *io)
 {
-	return (struct dm_verity_fec_io *) verity_io_digest_end(io->v, io);
+	return (struct dm_verity_fec_io *)
+		((char *)io + io->v->ti->per_io_data_size - sizeof(struct dm_verity_fec_io));
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-verity-target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-verity-target.c
@@ -482,7 +482,7 @@
 		sector_t cur_block = io->block + b;
 		struct ahash_request *req = verity_io_hash_req(v, io);
 
-		if (v->validated_blocks &&
+		if (v->validated_blocks && bio->bi_status == BLK_STS_OK &&
 		    likely(test_bit(cur_block, v->validated_blocks))) {
 			verity_bv_skip_block(v, io, &io->iter);
 			continue;
@@ -583,7 +583,9 @@
 	struct dm_verity_io *io = bio->bi_private;
 
 	if (bio->bi_status &&
-	    (!verity_fec_is_enabled(io->v) || verity_is_system_shutting_down())) {
+	    (!verity_fec_is_enabled(io->v) ||
+	     verity_is_system_shutting_down() ||
+	     (bio->bi_opf & REQ_RAHEAD))) {
 		verity_finish_io(io, bio->bi_status);
 		return;
 	}
@@ -1312,6 +1314,7 @@
 
 static struct target_type verity_target = {
 	.name		= "verity",
+	.features	= DM_TARGET_IMMUTABLE,
 	.version	= {1, 8, 0},
 	.module		= THIS_MODULE,
 	.ctr		= verity_ctr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-verity.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-verity.h
@@ -74,11 +74,11 @@
 	/* original value of bio->bi_end_io */
 	bio_end_io_t *orig_bi_end_io;
 
+	struct bvec_iter iter;
+
 	sector_t block;
 	unsigned n_blocks;
 
-	struct bvec_iter iter;
-
 	struct work_struct work;
 
 	/*
@@ -111,12 +111,6 @@
 	return (u8 *)(io + 1) + v->ahash_reqsize + v->digest_size;
 }
 
-static inline u8 *verity_io_digest_end(struct dm_verity *v,
-				       struct dm_verity_io *io)
-{
-	return verity_io_want_digest(v, io) + v->digest_size;
-}
-
 extern int verity_for_bv_block(struct dm_verity *v, struct dm_verity_io *io,
 			       struct bvec_iter *iter,
 			       int (*process)(struct dm_verity *v,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-writecache.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-writecache.c
@@ -22,7 +22,7 @@
 
 #define HIGH_WATERMARK			50
 #define LOW_WATERMARK			45
-#define MAX_WRITEBACK_JOBS		0
+#define MAX_WRITEBACK_JOBS		min(0x10000000 / PAGE_SIZE, totalram_pages() / 16)
 #define ENDIO_LATENCY			16
 #define WRITEBACK_LATENCY		64
 #define AUTOCOMMIT_BLOCKS_SSD		65536
@@ -1328,8 +1328,8 @@
 	WC_MAP_ERROR,
 };
 
-static enum wc_map_op writecache_map_remap_origin(struct dm_writecache *wc, struct bio *bio,
-						  struct wc_entry *e)
+static void writecache_map_remap_origin(struct dm_writecache *wc, struct bio *bio,
+					struct wc_entry *e)
 {
 	if (e) {
 		sector_t next_boundary =
@@ -1337,8 +1337,6 @@
 		if (next_boundary < bio->bi_iter.bi_size >> SECTOR_SHIFT)
 			dm_accept_partial_bio(bio, next_boundary);
 	}
-
-	return WC_MAP_REMAP_ORIGIN;
 }
 
 static enum wc_map_op writecache_map_read(struct dm_writecache *wc, struct bio *bio)
@@ -1365,14 +1363,16 @@
 			map_op = WC_MAP_REMAP;
 		}
 	} else {
-		map_op = writecache_map_remap_origin(wc, bio, e);
+		writecache_map_remap_origin(wc, bio, e);
+		wc->stats.reads += (bio->bi_iter.bi_size - wc->block_size) >> wc->block_size_bits;
+		map_op = WC_MAP_REMAP_ORIGIN;
 	}
 
 	return map_op;
 }
 
-static enum wc_map_op writecache_bio_copy_ssd(struct dm_writecache *wc, struct bio *bio,
-					      struct wc_entry *e, bool search_used)
+static void writecache_bio_copy_ssd(struct dm_writecache *wc, struct bio *bio,
+				    struct wc_entry *e, bool search_used)
 {
 	unsigned bio_size = wc->block_size;
 	sector_t start_cache_sec = cache_sector(wc, e);
@@ -1412,14 +1412,15 @@
 	bio->bi_iter.bi_sector = start_cache_sec;
 	dm_accept_partial_bio(bio, bio_size >> SECTOR_SHIFT);
 
+	wc->stats.writes += bio->bi_iter.bi_size >> wc->block_size_bits;
+	wc->stats.writes_allocate += (bio->bi_iter.bi_size - wc->block_size) >> wc->block_size_bits;
+
 	if (unlikely(wc->uncommitted_blocks >= wc->autocommit_blocks)) {
 		wc->uncommitted_blocks = 0;
 		queue_work(wc->writeback_wq, &wc->flush_work);
 	} else {
 		writecache_schedule_autocommit(wc);
 	}
-
-	return WC_MAP_REMAP;
 }
 
 static enum wc_map_op writecache_map_write(struct dm_writecache *wc, struct bio *bio)
@@ -1429,9 +1430,10 @@
 	do {
 		bool found_entry = false;
 		bool search_used = false;
-		wc->stats.writes++;
-		if (writecache_has_error(wc))
+		if (writecache_has_error(wc)) {
+			wc->stats.writes += bio->bi_iter.bi_size >> wc->block_size_bits;
 			return WC_MAP_ERROR;
+		}
 		e = writecache_find_entry(wc, bio->bi_iter.bi_sector, 0);
 		if (e) {
 			if (!writecache_entry_is_committed(wc, e)) {
@@ -1455,9 +1457,11 @@
 		if (unlikely(!e)) {
 			if (!WC_MODE_PMEM(wc) && !found_entry) {
 direct_write:
-				wc->stats.writes_around++;
 				e = writecache_find_entry(wc, bio->bi_iter.bi_sector, WFE_RETURN_FOLLOWING);
-				return writecache_map_remap_origin(wc, bio, e);
+				writecache_map_remap_origin(wc, bio, e);
+				wc->stats.writes_around += bio->bi_iter.bi_size >> wc->block_size_bits;
+				wc->stats.writes += bio->bi_iter.bi_size >> wc->block_size_bits;
+				return WC_MAP_REMAP_ORIGIN;
 			}
 			wc->stats.writes_blocked_on_freelist++;
 			writecache_wait_on_freelist(wc);
@@ -1468,10 +1472,13 @@
 		wc->uncommitted_blocks++;
 		wc->stats.writes_allocate++;
 bio_copy:
-		if (WC_MODE_PMEM(wc))
+		if (WC_MODE_PMEM(wc)) {
 			bio_copy_block(wc, bio, memory_data(wc, e));
-		else
-			return writecache_bio_copy_ssd(wc, bio, e, search_used);
+			wc->stats.writes++;
+		} else {
+			writecache_bio_copy_ssd(wc, bio, e, search_used);
+			return WC_MAP_REMAP;
+		}
 	} while (bio->bi_iter.bi_size);
 
 	if (unlikely(bio->bi_opf & REQ_FUA || wc->uncommitted_blocks >= wc->autocommit_blocks))
@@ -1506,7 +1513,7 @@
 
 static enum wc_map_op writecache_map_discard(struct dm_writecache *wc, struct bio *bio)
 {
-	wc->stats.discards++;
+	wc->stats.discards += bio->bi_iter.bi_size >> wc->block_size_bits;
 
 	if (writecache_has_error(wc))
 		return WC_MAP_ERROR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm-zoned-target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm-zoned-target.c
@@ -750,17 +750,16 @@
 /*
  * Cleanup zoned device information.
  */
-static void dmz_put_zoned_device(struct dm_target *ti)
+static void dmz_put_zoned_devices(struct dm_target *ti)
 {
 	struct dmz_target *dmz = ti->private;
 	int i;
 
-	for (i = 0; i < dmz->nr_ddevs; i++) {
-		if (dmz->ddev[i]) {
+	for (i = 0; i < dmz->nr_ddevs; i++)
+		if (dmz->ddev[i])
 			dm_put_device(ti, dmz->ddev[i]);
-			dmz->ddev[i] = NULL;
-		}
-	}
+
+	kfree(dmz->ddev);
 }
 
 static int dmz_fixup_devices(struct dm_target *ti)
@@ -951,7 +950,7 @@
 err_meta:
 	dmz_dtr_metadata(dmz->metadata);
 err_dev:
-	dmz_put_zoned_device(ti);
+	dmz_put_zoned_devices(ti);
 err:
 	kfree(dmz->dev);
 	kfree(dmz);
@@ -982,7 +981,7 @@
 
 	bioset_exit(&dmz->bio_set);
 
-	dmz_put_zoned_device(ti);
+	dmz_put_zoned_devices(ti);
 
 	mutex_destroy(&dmz->chunk_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm.c
@@ -226,7 +226,6 @@
 
 static void local_exit(void)
 {
-	flush_scheduled_work();
 	destroy_workqueue(deferred_remove_workqueue);
 
 	unregister_blkdev(_major, _name);
@@ -484,33 +483,48 @@
 }
 EXPORT_SYMBOL_GPL(dm_start_time_ns_from_clone);
 
-static void start_io_acct(struct dm_io *io)
+static bool bio_is_flush_with_data(struct bio *bio)
 {
-	struct mapped_device *md = io->md;
-	struct bio *bio = io->orig_bio;
-
-	io->start_time = bio_start_io_acct(bio);
-	if (unlikely(dm_stats_used(&md->stats)))
-		dm_stats_account_io(&md->stats, bio_data_dir(bio),
-				    bio->bi_iter.bi_sector, bio_sectors(bio),
-				    false, 0, &io->stats_aux);
+	return ((bio->bi_opf & REQ_PREFLUSH) && bio->bi_iter.bi_size);
 }
 
-static void end_io_acct(struct mapped_device *md, struct bio *bio,
-			unsigned long start_time, struct dm_stats_aux *stats_aux)
+static void dm_io_acct(bool end, struct mapped_device *md, struct bio *bio,
+		       unsigned long start_time, struct dm_stats_aux *stats_aux)
 {
-	unsigned long duration = jiffies - start_time;
+	bool is_flush_with_data;
+	unsigned int bi_size;
 
-	bio_end_io_acct(bio, start_time);
+	/* If REQ_PREFLUSH set save any payload but do not account it */
+	is_flush_with_data = bio_is_flush_with_data(bio);
+	if (is_flush_with_data) {
+		bi_size = bio->bi_iter.bi_size;
+		bio->bi_iter.bi_size = 0;
+	}
+
+	if (!end)
+		bio_start_io_acct_time(bio, start_time);
+	else
+		bio_end_io_acct(bio, start_time);
 
 	if (unlikely(dm_stats_used(&md->stats)))
 		dm_stats_account_io(&md->stats, bio_data_dir(bio),
 				    bio->bi_iter.bi_sector, bio_sectors(bio),
-				    true, duration, stats_aux);
+				    end, start_time, stats_aux);
+
+	/* Restore bio's payload so it does get accounted upon requeue */
+	if (is_flush_with_data)
+		bio->bi_iter.bi_size = bi_size;
+}
+
+static void start_io_acct(struct dm_io *io)
+{
+	dm_io_acct(false, io->md, io->orig_bio, io->start_time, &io->stats_aux);
+}
 
-	/* nudge anyone waiting on suspend queue */
-	if (unlikely(wq_has_sleeper(&md->wait)))
-		wake_up(&md->wait);
+static void end_io_acct(struct mapped_device *md, struct bio *bio,
+			unsigned long start_time, struct dm_stats_aux *stats_aux)
+{
+	dm_io_acct(true, md, bio, start_time, stats_aux);
 }
 
 static struct dm_io *alloc_io(struct mapped_device *md, struct bio *bio)
@@ -531,11 +545,14 @@
 	io->magic = DM_IO_MAGIC;
 	io->status = 0;
 	atomic_set(&io->io_count, 1);
+	this_cpu_inc(*md->pending_io);
 	io->orig_bio = bio;
 	io->md = md;
 	spin_lock_init(&io->endio_lock);
 
-	start_io_acct(io);
+	io->start_time = jiffies;
+
+	dm_stats_record_start(&md->stats, &io->stats_aux);
 
 	return io;
 }
@@ -826,11 +843,17 @@
 		stats_aux = io->stats_aux;
 		free_io(md, io);
 		end_io_acct(md, bio, start_time, &stats_aux);
+		smp_wmb();
+		this_cpu_dec(*md->pending_io);
+
+		/* nudge anyone waiting on suspend queue */
+		if (unlikely(wq_has_sleeper(&md->wait)))
+			wake_up(&md->wait);
 
 		if (io_error == BLK_STS_DM_REQUEUE)
 			return;
 
-		if ((bio->bi_opf & REQ_PREFLUSH) && bio->bi_iter.bi_size) {
+		if (bio_is_flush_with_data(bio)) {
 			/*
 			 * Preflush done for flush with data, reissue
 			 * without REQ_PREFLUSH.
@@ -1514,9 +1537,6 @@
 	ci->sector = bio->bi_iter.bi_sector;
 }
 
-#define __dm_part_stat_sub(part, field, subnd)	\
-	(part_stat_get(part, field) -= (subnd))
-
 /*
  * Entry point to split a bio into clones and submit them to the targets.
  */
@@ -1553,23 +1573,12 @@
 						  GFP_NOIO, &md->queue->bio_split);
 			ci.io->orig_bio = b;
 
-			/*
-			 * Adjust IO stats for each split, otherwise upon queue
-			 * reentry there will be redundant IO accounting.
-			 * NOTE: this is a stop-gap fix, a proper fix involves
-			 * significant refactoring of DM core's bio splitting
-			 * (by eliminating DM's splitting and just using bio_split)
-			 */
-			part_stat_lock();
-			__dm_part_stat_sub(dm_disk(md)->part0,
-					   sectors[op_stat_group(bio_op(bio))], ci.sector_count);
-			part_stat_unlock();
-
 			bio_chain(b, bio);
 			trace_block_split(b, bio->bi_iter.bi_sector);
 			ret = submit_bio_noacct(bio);
 		}
 	}
+	start_io_acct(ci.io);
 
 	/* drop the extra reference count */
 	dm_io_dec_pending(ci.io, errno_to_blk_status(error));
@@ -1696,6 +1705,7 @@
 		md->dax_dev = NULL;
 	}
 
+	dm_cleanup_zoned_dev(md);
 	if (md->disk) {
 		spin_lock(&_minor_lock);
 		md->disk->private_data = NULL;
@@ -1708,6 +1718,11 @@
 		blk_cleanup_disk(md->disk);
 	}
 
+	if (md->pending_io) {
+		free_percpu(md->pending_io);
+		md->pending_io = NULL;
+	}
+
 	cleanup_srcu_struct(&md->io_barrier);
 
 	mutex_destroy(&md->suspend_lock);
@@ -1716,7 +1731,6 @@
 	mutex_destroy(&md->swap_bios_lock);
 
 	dm_mq_cleanup_mapped_device(md);
-	dm_cleanup_zoned_dev(md);
 }
 
 /*
@@ -1787,15 +1801,16 @@
 	md->disk->first_minor = minor;
 	md->disk->minors = 1;
 	md->disk->fops = &dm_blk_dops;
-	md->disk->queue = md->queue;
 	md->disk->private_data = md;
 	sprintf(md->disk->disk_name, "dm-%d", minor);
 
 	if (IS_ENABLED(CONFIG_DAX_DRIVER)) {
 		md->dax_dev = alloc_dax(md, md->disk->disk_name,
 					&dm_dax_ops, 0);
-		if (IS_ERR(md->dax_dev))
+		if (IS_ERR(md->dax_dev)) {
+			md->dax_dev = NULL;
 			goto bad;
+		}
 	}
 
 	format_dev_t(md->name, MKDEV(_major, minor));
@@ -1804,7 +1819,13 @@
 	if (!md->wq)
 		goto bad;
 
-	dm_stats_init(&md->stats);
+	md->pending_io = alloc_percpu(unsigned long);
+	if (!md->pending_io)
+		goto bad;
+
+	r = dm_stats_init(&md->stats);
+	if (r < 0)
+		goto bad;
 
 	/* Populate the mapping, nobody knows we exist yet */
 	spin_lock(&_minor_lock);
@@ -1928,10 +1949,7 @@
 	if (size != dm_get_size(md))
 		memset(&md->geometry, 0, sizeof(md->geometry));
 
-	if (!get_capacity(md->disk))
-		set_capacity(md->disk, size);
-	else
-		set_capacity_and_notify(md->disk, size);
+	set_capacity(md->disk, size);
 
 	dm_table_event_callback(t, event_callback, md);
 
@@ -2168,7 +2186,7 @@
 	set_bit(DMF_FREEING, &md->flags);
 	spin_unlock(&_minor_lock);
 
-	blk_set_queue_dying(md->queue);
+	blk_mark_disk_dead(md->disk);
 
 	/*
 	 * Take suspend_lock so that presuspend and postsuspend methods
@@ -2219,16 +2237,13 @@
 }
 EXPORT_SYMBOL_GPL(dm_put);
 
-static bool md_in_flight_bios(struct mapped_device *md)
+static bool dm_in_flight_bios(struct mapped_device *md)
 {
 	int cpu;
-	struct block_device *part = dm_disk(md)->part0;
-	long sum = 0;
+	unsigned long sum = 0;
 
-	for_each_possible_cpu(cpu) {
-		sum += part_stat_local_read_cpu(part, in_flight[0], cpu);
-		sum += part_stat_local_read_cpu(part, in_flight[1], cpu);
-	}
+	for_each_possible_cpu(cpu)
+		sum += *per_cpu_ptr(md->pending_io, cpu);
 
 	return sum != 0;
 }
@@ -2241,11 +2256,11 @@
 	while (true) {
 		prepare_to_wait(&md->wait, &wait, task_state);
 
-		if (!md_in_flight_bios(md))
+		if (!dm_in_flight_bios(md))
 			break;
 
 		if (signal_pending_state(task_state, current)) {
-			r = -EINTR;
+			r = -ERESTARTSYS;
 			break;
 		}
 
@@ -2253,6 +2268,8 @@
 	}
 	finish_wait(&md->wait, &wait);
 
+	smp_rmb();
+
 	return r;
 }
 
@@ -2268,7 +2285,7 @@
 			break;
 
 		if (signal_pending_state(task_state, current)) {
-			r = -EINTR;
+			r = -ERESTARTSYS;
 			break;
 		}
 
@@ -2295,6 +2312,7 @@
 			break;
 
 		submit_bio_noacct(bio);
+		cond_resched();
 	}
 }
 
@@ -2513,6 +2531,10 @@
 	}
 
 	map = rcu_dereference_protected(md->map, lockdep_is_held(&md->suspend_lock));
+	if (!map) {
+		/* avoid deadlock with fs/namespace.c:do_mount() */
+		suspend_flags &= ~DM_SUSPEND_LOCKFS_FLAG;
+	}
 
 	r = __dm_suspend(md, map, suspend_flags, TASK_INTERRUPTIBLE, DMF_SUSPENDED);
 	if (r)
@@ -2624,6 +2646,9 @@
 
 static void __dm_internal_resume(struct mapped_device *md)
 {
+	int r;
+	struct dm_table *map;
+
 	BUG_ON(!md->internal_suspend_count);
 
 	if (--md->internal_suspend_count)
@@ -2632,12 +2657,23 @@
 	if (dm_suspended_md(md))
 		goto done; /* resume from nested suspend */
 
-	/*
-	 * NOTE: existing callers don't need to call dm_table_resume_targets
-	 * (which may fail -- so best to avoid it for now by passing NULL map)
-	 */
-	(void) __dm_resume(md, NULL);
-
+	map = rcu_dereference_protected(md->map, lockdep_is_held(&md->suspend_lock));
+	r = __dm_resume(md, map);
+	if (r) {
+		/*
+		 * If a preresume method of some target failed, we are in a
+		 * tricky situation. We can't return an error to the caller. We
+		 * can't fake success because then the "resume" and
+		 * "postsuspend" methods would not be paired correctly, and it
+		 * would break various targets, for example it would cause list
+		 * corruption in the "origin" target.
+		 *
+		 * So, we fake normal suspend here, to make sure that the
+		 * "resume" and "postsuspend" methods will be paired correctly.
+		 */
+		DMERR("Preresume method failed: %d", r);
+		set_bit(DMF_SUSPENDED, &md->flags);
+	}
 done:
 	clear_bit(DMF_SUSPENDED_INTERNALLY, &md->flags);
 	smp_mb__after_atomic();
@@ -2694,23 +2730,25 @@
  * Event notification.
  *---------------------------------------------------------------*/
 int dm_kobject_uevent(struct mapped_device *md, enum kobject_action action,
-		       unsigned cookie)
+		      unsigned cookie, bool need_resize_uevent)
 {
 	int r;
 	unsigned noio_flag;
 	char udev_cookie[DM_COOKIE_LENGTH];
-	char *envp[] = { udev_cookie, NULL };
-
-	noio_flag = memalloc_noio_save();
-
-	if (!cookie)
-		r = kobject_uevent(&disk_to_dev(md->disk)->kobj, action);
-	else {
+	char *envp[3] = { NULL, NULL, NULL };
+	char **envpp = envp;
+	if (cookie) {
 		snprintf(udev_cookie, DM_COOKIE_LENGTH, "%s=%u",
 			 DM_COOKIE_ENV_VAR_NAME, cookie);
-		r = kobject_uevent_env(&disk_to_dev(md->disk)->kobj,
-				       action, envp);
+		*envpp++ = udev_cookie;
 	}
+	if (need_resize_uevent) {
+		*envpp++ = "RESIZE=1";
+	}
+
+	noio_flag = memalloc_noio_save();
+
+	r = kobject_uevent_env(&disk_to_dev(md->disk)->kobj, action, envp);
 
 	memalloc_noio_restore(noio_flag);
 
@@ -2896,6 +2934,11 @@
 		goto out;
 	ti = dm_table_get_target(table, 0);
 
+	if (dm_suspended_md(md)) {
+		ret = -EAGAIN;
+		goto out;
+	}
+
 	ret = -EINVAL;
 	if (!ti->type->iterate_devices)
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/dm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/dm.h
@@ -210,7 +210,7 @@
 void dm_put_table_device(struct mapped_device *md, struct dm_dev *d);
 
 int dm_kobject_uevent(struct mapped_device *md, enum kobject_action action,
-		      unsigned cookie);
+		      unsigned cookie, bool need_resize_uevent);
 
 void dm_internal_suspend(struct mapped_device *md);
 void dm_internal_resume(struct mapped_device *md);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/md-bitmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/md-bitmap.c
@@ -54,14 +54,7 @@
 {
 	unsigned char *mappage;
 
-	if (page >= bitmap->pages) {
-		/* This can happen if bitmap_start_sync goes beyond
-		 * End-of-device while looking for a whole page.
-		 * It is harmless.
-		 */
-		return -EINVAL;
-	}
-
+	WARN_ON_ONCE(page >= bitmap->pages);
 	if (bitmap->bp[page].hijacked) /* it's hijacked, don't try to alloc */
 		return 0;
 
@@ -486,7 +479,7 @@
 	sb = kmap_atomic(bitmap->storage.sb_page);
 	pr_debug("%s: bitmap file superblock:\n", bmname(bitmap));
 	pr_debug("         magic: %08x\n", le32_to_cpu(sb->magic));
-	pr_debug("       version: %d\n", le32_to_cpu(sb->version));
+	pr_debug("       version: %u\n", le32_to_cpu(sb->version));
 	pr_debug("          uuid: %08x.%08x.%08x.%08x\n",
 		 le32_to_cpu(*(__le32 *)(sb->uuid+0)),
 		 le32_to_cpu(*(__le32 *)(sb->uuid+4)),
@@ -497,11 +490,11 @@
 	pr_debug("events cleared: %llu\n",
 		 (unsigned long long) le64_to_cpu(sb->events_cleared));
 	pr_debug("         state: %08x\n", le32_to_cpu(sb->state));
-	pr_debug("     chunksize: %d B\n", le32_to_cpu(sb->chunksize));
-	pr_debug("  daemon sleep: %ds\n", le32_to_cpu(sb->daemon_sleep));
+	pr_debug("     chunksize: %u B\n", le32_to_cpu(sb->chunksize));
+	pr_debug("  daemon sleep: %us\n", le32_to_cpu(sb->daemon_sleep));
 	pr_debug("     sync size: %llu KB\n",
 		 (unsigned long long)le64_to_cpu(sb->sync_size)/2);
-	pr_debug("max write behind: %d\n", le32_to_cpu(sb->write_behind));
+	pr_debug("max write behind: %u\n", le32_to_cpu(sb->write_behind));
 	kunmap_atomic(sb);
 }
 
@@ -639,14 +632,6 @@
 	daemon_sleep = le32_to_cpu(sb->daemon_sleep) * HZ;
 	write_behind = le32_to_cpu(sb->write_behind);
 	sectors_reserved = le32_to_cpu(sb->sectors_reserved);
-	/* Setup nodes/clustername only if bitmap version is
-	 * cluster-compatible
-	 */
-	if (sb->version == cpu_to_le32(BITMAP_MAJOR_CLUSTERED)) {
-		nodes = le32_to_cpu(sb->nodes);
-		strlcpy(bitmap->mddev->bitmap_info.cluster_name,
-				sb->cluster_name, 64);
-	}
 
 	/* verify that the bitmap-specific fields are valid */
 	if (sb->magic != cpu_to_le32(BITMAP_MAGIC))
@@ -668,6 +653,16 @@
 		goto out;
 	}
 
+	/*
+	 * Setup nodes/clustername only if bitmap version is
+	 * cluster-compatible
+	 */
+	if (sb->version == cpu_to_le32(BITMAP_MAJOR_CLUSTERED)) {
+		nodes = le32_to_cpu(sb->nodes);
+		strlcpy(bitmap->mddev->bitmap_info.cluster_name,
+				sb->cluster_name, 64);
+	}
+
 	/* keep the array size field of the bitmap superblock up to date */
 	sb->sync_size = cpu_to_le64(bitmap->mddev->resync_max_sectors);
 
@@ -700,9 +695,9 @@
 
 out:
 	kunmap_atomic(sb);
-	/* Assigning chunksize is required for "re_read" */
-	bitmap->mddev->bitmap_info.chunksize = chunksize;
 	if (err == 0 && nodes && (bitmap->cluster_slot < 0)) {
+		/* Assigning chunksize is required for "re_read" */
+		bitmap->mddev->bitmap_info.chunksize = chunksize;
 		err = md_setup_cluster(bitmap->mddev, nodes);
 		if (err) {
 			pr_warn("%s: Could not setup cluster service (%d)\n",
@@ -713,18 +708,18 @@
 		goto re_read;
 	}
 
-
 out_no_sb:
-	if (test_bit(BITMAP_STALE, &bitmap->flags))
-		bitmap->events_cleared = bitmap->mddev->events;
-	bitmap->mddev->bitmap_info.chunksize = chunksize;
-	bitmap->mddev->bitmap_info.daemon_sleep = daemon_sleep;
-	bitmap->mddev->bitmap_info.max_write_behind = write_behind;
-	bitmap->mddev->bitmap_info.nodes = nodes;
-	if (bitmap->mddev->bitmap_info.space == 0 ||
-	    bitmap->mddev->bitmap_info.space > sectors_reserved)
-		bitmap->mddev->bitmap_info.space = sectors_reserved;
-	if (err) {
+	if (err == 0) {
+		if (test_bit(BITMAP_STALE, &bitmap->flags))
+			bitmap->events_cleared = bitmap->mddev->events;
+		bitmap->mddev->bitmap_info.chunksize = chunksize;
+		bitmap->mddev->bitmap_info.daemon_sleep = daemon_sleep;
+		bitmap->mddev->bitmap_info.max_write_behind = write_behind;
+		bitmap->mddev->bitmap_info.nodes = nodes;
+		if (bitmap->mddev->bitmap_info.space == 0 ||
+			bitmap->mddev->bitmap_info.space > sectors_reserved)
+			bitmap->mddev->bitmap_info.space = sectors_reserved;
+	} else {
 		md_bitmap_print_sb(bitmap);
 		if (bitmap->cluster_slot < 0)
 			md_cluster_stop(bitmap->mddev);
@@ -1360,17 +1355,25 @@
 	sector_t chunk = offset >> bitmap->chunkshift;
 	unsigned long page = chunk >> PAGE_COUNTER_SHIFT;
 	unsigned long pageoff = (chunk & PAGE_COUNTER_MASK) << COUNTER_BYTE_SHIFT;
-	sector_t csize;
+	sector_t csize = ((sector_t)1) << bitmap->chunkshift;
 	int err;
 
+	if (page >= bitmap->pages) {
+		/*
+		 * This can happen if bitmap_start_sync goes beyond
+		 * End-of-device while looking for a whole page or
+		 * user set a huge number to sysfs bitmap_set_bits.
+		 */
+		*blocks = csize - (offset & (csize - 1));
+		return NULL;
+	}
 	err = md_bitmap_checkpage(bitmap, page, create, 0);
 
 	if (bitmap->bp[page].hijacked ||
 	    bitmap->bp[page].map == NULL)
 		csize = ((sector_t)1) << (bitmap->chunkshift +
 					  PAGE_COUNTER_SHIFT);
-	else
-		csize = ((sector_t)1) << bitmap->chunkshift;
+
 	*blocks = csize - (offset & (csize - 1));
 
 	if (err < 0)
@@ -2104,7 +2107,8 @@
 			bytes = DIV_ROUND_UP(chunks, 8);
 			if (!bitmap->mddev->bitmap_info.external)
 				bytes += sizeof(bitmap_super_t);
-		} while (bytes > (space << 9));
+		} while (bytes > (space << 9) && (chunkshift + BITMAP_BLOCK_SHIFT) <
+			(BITS_PER_BYTE * sizeof(((bitmap_super_t *)0)->chunksize) - 1));
 	} else
 		chunkshift = ffz(~chunksize) - BITMAP_BLOCK_SHIFT;
 
@@ -2149,7 +2153,7 @@
 	bitmap->counts.missing_pages = pages;
 	bitmap->counts.chunkshift = chunkshift;
 	bitmap->counts.chunks = chunks;
-	bitmap->mddev->bitmap_info.chunksize = 1 << (chunkshift +
+	bitmap->mddev->bitmap_info.chunksize = 1UL << (chunkshift +
 						     BITMAP_BLOCK_SHIFT);
 
 	blocks = min(old_counts.chunks << old_counts.chunkshift,
@@ -2175,8 +2179,8 @@
 				bitmap->counts.missing_pages = old_counts.pages;
 				bitmap->counts.chunkshift = old_counts.chunkshift;
 				bitmap->counts.chunks = old_counts.chunks;
-				bitmap->mddev->bitmap_info.chunksize = 1 << (old_counts.chunkshift +
-									     BITMAP_BLOCK_SHIFT);
+				bitmap->mddev->bitmap_info.chunksize =
+					1UL << (old_counts.chunkshift + BITMAP_BLOCK_SHIFT);
 				blocks = old_counts.chunks << old_counts.chunkshift;
 				pr_warn("Could not pre-allocate in-memory bitmap for cluster raid\n");
 				break;
@@ -2194,20 +2198,23 @@
 
 		if (set) {
 			bmc_new = md_bitmap_get_counter(&bitmap->counts, block, &new_blocks, 1);
-			if (*bmc_new == 0) {
-				/* need to set on-disk bits too. */
-				sector_t end = block + new_blocks;
-				sector_t start = block >> chunkshift;
-				start <<= chunkshift;
-				while (start < end) {
-					md_bitmap_file_set_bit(bitmap, block);
-					start += 1 << chunkshift;
+			if (bmc_new) {
+				if (*bmc_new == 0) {
+					/* need to set on-disk bits too. */
+					sector_t end = block + new_blocks;
+					sector_t start = block >> chunkshift;
+
+					start <<= chunkshift;
+					while (start < end) {
+						md_bitmap_file_set_bit(bitmap, block);
+						start += 1 << chunkshift;
+					}
+					*bmc_new = 2;
+					md_bitmap_count_page(&bitmap->counts, block, 1);
+					md_bitmap_set_pending(&bitmap->counts, block);
 				}
-				*bmc_new = 2;
-				md_bitmap_count_page(&bitmap->counts, block, 1);
-				md_bitmap_set_pending(&bitmap->counts, block);
+				*bmc_new |= NEEDED_MASK;
 			}
-			*bmc_new |= NEEDED_MASK;
 			if (new_blocks < old_blocks)
 				old_blocks = new_blocks;
 		}
@@ -2469,11 +2476,35 @@
 {
 	unsigned long backlog;
 	unsigned long old_mwb = mddev->bitmap_info.max_write_behind;
+	struct md_rdev *rdev;
+	bool has_write_mostly = false;
 	int rv = kstrtoul(buf, 10, &backlog);
 	if (rv)
 		return rv;
 	if (backlog > COUNTER_MAX)
 		return -EINVAL;
+
+	rv = mddev_lock(mddev);
+	if (rv)
+		return rv;
+
+	/*
+	 * Without write mostly device, it doesn't make sense to set
+	 * backlog for max_write_behind.
+	 */
+	rdev_for_each(rdev, mddev) {
+		if (test_bit(WriteMostly, &rdev->flags)) {
+			has_write_mostly = true;
+			break;
+		}
+	}
+	if (!has_write_mostly) {
+		pr_warn_ratelimited("%s: can't set backlog, no write mostly device available\n",
+				    mdname(mddev));
+		mddev_unlock(mddev);
+		return -EINVAL;
+	}
+
 	mddev->bitmap_info.max_write_behind = backlog;
 	if (!backlog && mddev->serial_info_pool) {
 		/* serial_info_pool is not needed if backlog is zero */
@@ -2481,13 +2512,13 @@
 			mddev_destroy_serial_pool(mddev, NULL, false);
 	} else if (backlog && !mddev->serial_info_pool) {
 		/* serial_info_pool is needed since backlog is not zero */
-		struct md_rdev *rdev;
-
 		rdev_for_each(rdev, mddev)
 			mddev_create_serial_pool(mddev, rdev, false);
 	}
 	if (old_mwb != backlog)
 		md_bitmap_update_sb(mddev->bitmap);
+
+	mddev_unlock(mddev);
 	return len;
 }
 
@@ -2514,6 +2545,9 @@
 	if (csize < 512 ||
 	    !is_power_of_2(csize))
 		return -EINVAL;
+	if (BITS_PER_LONG > 32 && csize >= (1ULL << (BITS_PER_BYTE *
+		sizeof(((bitmap_super_t *)0)->chunksize))))
+		return -EOVERFLOW;
 	mddev->bitmap_info.chunksize = csize;
 	return len;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/md-linear.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/md-linear.c
@@ -233,7 +233,8 @@
 		     bio_sector < start_sector))
 		goto out_of_bounds;
 
-	if (unlikely(is_mddev_broken(tmp_dev->rdev, "linear"))) {
+	if (unlikely(is_rdev_broken(tmp_dev->rdev))) {
+		md_error(mddev, tmp_dev->rdev);
 		bio_io_error(bio);
 		return true;
 	}
@@ -281,6 +282,16 @@
 	seq_printf(seq, " %dk rounding", mddev->chunk_sectors / 2);
 }
 
+static void linear_error(struct mddev *mddev, struct md_rdev *rdev)
+{
+	if (!test_and_set_bit(MD_BROKEN, &mddev->flags)) {
+		char *md_name = mdname(mddev);
+
+		pr_crit("md/linear%s: Disk failure on %pg detected, failing array.\n",
+			md_name, rdev->bdev);
+	}
+}
+
 static void linear_quiesce(struct mddev *mddev, int state)
 {
 }
@@ -297,6 +308,7 @@
 	.hot_add_disk	= linear_add,
 	.size		= linear_size,
 	.quiesce	= linear_quiesce,
+	.error_handler	= linear_error,
 };
 
 static int __init linear_init (void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/md.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/md.c
@@ -51,6 +51,7 @@
 #include <linux/hdreg.h>
 #include <linux/proc_fs.h>
 #include <linux/random.h>
+#include <linux/major.h>
 #include <linux/module.h>
 #include <linux/reboot.h>
 #include <linux/file.h>
@@ -91,6 +92,18 @@
 				 struct md_rdev *this);
 static void mddev_detach(struct mddev *mddev);
 
+enum md_ro_state {
+	MD_RDWR,
+	MD_RDONLY,
+	MD_AUTO_READ,
+	MD_MAX_STATE
+};
+
+static bool md_is_rdwr(struct mddev *mddev)
+{
+	return (mddev->ro == MD_RDWR);
+}
+
 /*
  * Default number of read corrections we'll attempt on an rdev
  * before ejecting it from the array. We divide the read error
@@ -457,8 +470,10 @@
 	}
 
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
-	if (mddev->ro == 1 && unlikely(rw == WRITE)) {
+	if (mddev->ro == MD_RDONLY && unlikely(rw == WRITE)) {
 		if (bio_sectors(bio) != 0)
 			bio->bi_status = BLK_STS_IOERR;
 		bio_endio(bio);
@@ -494,7 +509,6 @@
 	clear_bit_unlock(MD_ALLOW_SB_UPDATE, &mddev->flags);
 	wait_event(mddev->sb_wait, !test_bit(MD_UPDATING_SB, &mddev->flags));
 
-	del_timer_sync(&mddev->safemode_timer);
 	/* restrict memory reclaim I/O during raid array is suspend */
 	mddev->noio_flag = memalloc_noio_save();
 }
@@ -525,13 +539,14 @@
 	struct md_rdev *rdev = bio->bi_private;
 	struct mddev *mddev = rdev->mddev;
 
+	bio_put(bio);
+
 	rdev_dec_pending(rdev, mddev);
 
 	if (atomic_dec_and_test(&mddev->flush_pending)) {
 		/* The pre-request flush has finished */
 		queue_work(md_wq, &mddev->flush_work);
 	}
-	bio_put(bio);
 }
 
 static void md_submit_flush_data(struct work_struct *ws);
@@ -934,10 +949,12 @@
 	} else
 		clear_bit(LastDev, &rdev->flags);
 
+	bio_put(bio);
+
+	rdev_dec_pending(rdev, mddev);
+
 	if (atomic_dec_and_test(&mddev->pending_writes))
 		wake_up(&mddev->sb_wait);
-	rdev_dec_pending(rdev, mddev);
-	bio_put(bio);
 }
 
 void md_super_write(struct mddev *mddev, struct md_rdev *rdev,
@@ -1144,6 +1161,7 @@
 					  struct md_rdev *refdev,
 					  int minor_version);
 	int		    (*validate_super)(struct mddev *mddev,
+					      struct md_rdev *freshest,
 					      struct md_rdev *rdev);
 	void		    (*sync_super)(struct mddev *mddev,
 					  struct md_rdev *rdev);
@@ -1282,8 +1300,9 @@
 
 /*
  * validate_super for 0.90.0
+ * note: we are not using "freshest" for 0.9 superblock
  */
-static int super_90_validate(struct mddev *mddev, struct md_rdev *rdev)
+static int super_90_validate(struct mddev *mddev, struct md_rdev *freshest, struct md_rdev *rdev)
 {
 	mdp_disk_t *desc;
 	mdp_super_t *sb = page_address(rdev->sb_page);
@@ -1798,7 +1817,7 @@
 	return ret;
 }
 
-static int super_1_validate(struct mddev *mddev, struct md_rdev *rdev)
+static int super_1_validate(struct mddev *mddev, struct md_rdev *freshest, struct md_rdev *rdev)
 {
 	struct mdp_superblock_1 *sb = page_address(rdev->sb_page);
 	__u64 ev1 = le64_to_cpu(sb->events);
@@ -1894,13 +1913,15 @@
 		}
 	} else if (mddev->pers == NULL) {
 		/* Insist of good event counter while assembling, except for
-		 * spares (which don't need an event count) */
-		++ev1;
+		 * spares (which don't need an event count).
+		 * Similar to mdadm, we allow event counter difference of 1
+		 * from the freshest device.
+		 */
 		if (rdev->desc_nr >= 0 &&
 		    rdev->desc_nr < le32_to_cpu(sb->max_dev) &&
 		    (le16_to_cpu(sb->dev_roles[rdev->desc_nr]) < MD_DISK_ROLE_MAX ||
 		     le16_to_cpu(sb->dev_roles[rdev->desc_nr]) == MD_DISK_ROLE_JOURNAL))
-			if (ev1 < mddev->events)
+			if (ev1 + 1 < mddev->events)
 				return -EINVAL;
 	} else if (mddev->bitmap) {
 		/* If adding to array with a bitmap, then we can accept an
@@ -1921,8 +1942,38 @@
 		    rdev->desc_nr >= le32_to_cpu(sb->max_dev)) {
 			role = MD_DISK_ROLE_SPARE;
 			rdev->desc_nr = -1;
-		} else
+		} else if (mddev->pers == NULL && freshest && ev1 < mddev->events) {
+			/*
+			 * If we are assembling, and our event counter is smaller than the
+			 * highest event counter, we cannot trust our superblock about the role.
+			 * It could happen that our rdev was marked as Faulty, and all other
+			 * superblocks were updated with +1 event counter.
+			 * Then, before the next superblock update, which typically happens when
+			 * remove_and_add_spares() removes the device from the array, there was
+			 * a crash or reboot.
+			 * If we allow current rdev without consulting the freshest superblock,
+			 * we could cause data corruption.
+			 * Note that in this case our event counter is smaller by 1 than the
+			 * highest, otherwise, this rdev would not be allowed into array;
+			 * both kernel and mdadm allow event counter difference of 1.
+			 */
+			struct mdp_superblock_1 *freshest_sb = page_address(freshest->sb_page);
+			u32 freshest_max_dev = le32_to_cpu(freshest_sb->max_dev);
+
+			if (rdev->desc_nr >= freshest_max_dev) {
+				/* this is unexpected, better not proceed */
+				pr_warn("md: %s: rdev[%pg]: desc_nr(%d) >= freshest(%pg)->sb->max_dev(%u)\n",
+						mdname(mddev), rdev->bdev, rdev->desc_nr,
+						freshest->bdev, freshest_max_dev);
+				return -EUCLEAN;
+			}
+
+			role = le16_to_cpu(freshest_sb->dev_roles[rdev->desc_nr]);
+			pr_debug("md: %s: rdev[%pg]: role=%d(0x%x) according to freshest %pg\n",
+				     mdname(mddev), rdev->bdev, role, role, freshest->bdev);
+		} else {
 			role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]);
+		}
 		switch(role) {
 		case MD_DISK_ROLE_SPARE: /* spare */
 			break;
@@ -2193,6 +2244,7 @@
 
 		if (!num_sectors || num_sectors > max_sectors)
 			num_sectors = max_sectors;
+		rdev->sb_start = sb_start;
 	}
 	sb = page_address(rdev->sb_page);
 	sb->data_size = cpu_to_le64(num_sectors);
@@ -2473,6 +2525,7 @@
  fail:
 	pr_warn("md: failed to register dev-%s for %s\n",
 		b, mdname(mddev));
+	mddev_destroy_serial_pool(mddev, rdev, false);
 	return err;
 }
 
@@ -2626,14 +2679,16 @@
 
 static bool does_sb_need_changing(struct mddev *mddev)
 {
-	struct md_rdev *rdev;
+	struct md_rdev *rdev = NULL, *iter;
 	struct mdp_superblock_1 *sb;
 	int role;
 
 	/* Find a good rdev */
-	rdev_for_each(rdev, mddev)
-		if ((rdev->raid_disk >= 0) && !test_bit(Faulty, &rdev->flags))
+	rdev_for_each(iter, mddev)
+		if ((iter->raid_disk >= 0) && !test_bit(Faulty, &iter->flags)) {
+			rdev = iter;
 			break;
+		}
 
 	/* No good device found. */
 	if (!rdev)
@@ -2671,7 +2726,7 @@
 	int any_badblocks_changed = 0;
 	int ret = -1;
 
-	if (mddev->ro) {
+	if (!md_is_rdwr(mddev)) {
 		if (force_change)
 			set_bit(MD_SB_CHANGE_DEVS, &mddev->sb_flags);
 		return;
@@ -2869,7 +2924,7 @@
 		 * and should be added immediately.
 		 */
 		super_types[mddev->major_version].
-			validate_super(mddev, rdev);
+			validate_super(mddev, NULL/*freshest*/, rdev);
 		if (add_journal)
 			mddev_suspend(mddev);
 		err = mddev->pers->hot_add_disk(mddev, rdev);
@@ -2976,13 +3031,18 @@
 	 *  -write_error - clears WriteErrorSeen
 	 *  {,-}failfast - set/clear FailFast
 	 */
+
+	struct mddev *mddev = rdev->mddev;
 	int err = -EINVAL;
+	bool need_update_sb = false;
+
 	if (cmd_match(buf, "faulty") && rdev->mddev->pers) {
 		md_error(rdev->mddev, rdev);
-		if (test_bit(Faulty, &rdev->flags))
-			err = 0;
-		else
+
+		if (test_bit(MD_BROKEN, &rdev->mddev->flags))
 			err = -EBUSY;
+		else
+			err = 0;
 	} else if (cmd_match(buf, "remove")) {
 		if (rdev->mddev->pers) {
 			clear_bit(Blocked, &rdev->flags);
@@ -2991,7 +3051,6 @@
 		if (rdev->raid_disk >= 0)
 			err = -EBUSY;
 		else {
-			struct mddev *mddev = rdev->mddev;
 			err = 0;
 			if (mddev_is_clustered(mddev))
 				err = md_cluster_ops->remove_disk(mddev, rdev);
@@ -3008,10 +3067,12 @@
 	} else if (cmd_match(buf, "writemostly")) {
 		set_bit(WriteMostly, &rdev->flags);
 		mddev_create_serial_pool(rdev->mddev, rdev, false);
+		need_update_sb = true;
 		err = 0;
 	} else if (cmd_match(buf, "-writemostly")) {
 		mddev_destroy_serial_pool(rdev->mddev, rdev, false);
 		clear_bit(WriteMostly, &rdev->flags);
+		need_update_sb = true;
 		err = 0;
 	} else if (cmd_match(buf, "blocked")) {
 		set_bit(Blocked, &rdev->flags);
@@ -3037,9 +3098,11 @@
 		err = 0;
 	} else if (cmd_match(buf, "failfast")) {
 		set_bit(FailFast, &rdev->flags);
+		need_update_sb = true;
 		err = 0;
 	} else if (cmd_match(buf, "-failfast")) {
 		clear_bit(FailFast, &rdev->flags);
+		need_update_sb = true;
 		err = 0;
 	} else if (cmd_match(buf, "-insync") && rdev->raid_disk >= 0 &&
 		   !test_bit(Journal, &rdev->flags)) {
@@ -3118,6 +3181,8 @@
 		clear_bit(ExternalBbl, &rdev->flags);
 		err = 0;
 	}
+	if (need_update_sb)
+		md_update_sb(mddev, 1);
 	if (!err)
 		sysfs_notify_dirent_safe(rdev->sysfs_state);
 	return err ? err : len;
@@ -3171,6 +3236,9 @@
 		err = kstrtouint(buf, 10, (unsigned int *)&slot);
 		if (err < 0)
 			return err;
+		if (slot < 0)
+			/* overflow */
+			return -ENOSPC;
 	}
 	if (rdev->mddev->pers && slot == -1) {
 		/* Setting 'slot' on an active array requires also
@@ -3775,7 +3843,7 @@
 	}
 
 	super_types[mddev->major_version].
-		validate_super(mddev, freshest);
+		validate_super(mddev, NULL/*freshest*/, freshest);
 
 	i = 0;
 	rdev_for_each_safe(rdev, tmp, mddev) {
@@ -3790,7 +3858,7 @@
 		}
 		if (rdev != freshest) {
 			if (super_types[mddev->major_version].
-			    validate_super(mddev, rdev)) {
+			    validate_super(mddev, freshest, rdev)) {
 				pr_warn("md: kicking non-fresh %s from array!\n",
 					bdevname(rdev->bdev,b));
 				md_kick_rdev_from_array(rdev);
@@ -3851,8 +3919,9 @@
 static ssize_t
 safe_delay_show(struct mddev *mddev, char *page)
 {
-	int msec = (mddev->safemode_delay*1000)/HZ;
-	return sprintf(page, "%d.%03d\n", msec/1000, msec%1000);
+	unsigned int msec = ((unsigned long)mddev->safemode_delay*1000)/HZ;
+
+	return sprintf(page, "%u.%03u\n", msec/1000, msec%1000);
 }
 static ssize_t
 safe_delay_store(struct mddev *mddev, const char *cbuf, size_t len)
@@ -3864,7 +3933,7 @@
 		return -EINVAL;
 	}
 
-	if (strict_strtoul_scaled(cbuf, &msec, 3) < 0)
+	if (strict_strtoul_scaled(cbuf, &msec, 3) < 0 || msec > UINT_MAX / HZ)
 		return -EINVAL;
 	if (msec == 0)
 		mddev->safemode_delay = 0;
@@ -3930,7 +3999,7 @@
 		goto out_unlock;
 	}
 	rv = -EROFS;
-	if (mddev->ro)
+	if (!md_is_rdwr(mddev))
 		goto out_unlock;
 
 	/* request to change the personality.  Need to ensure:
@@ -4136,7 +4205,7 @@
 	if (mddev->pers) {
 		if (mddev->pers->check_reshape == NULL)
 			err = -EBUSY;
-		else if (mddev->ro)
+		else if (!md_is_rdwr(mddev))
 			err = -EROFS;
 		else {
 			mddev->new_layout = n;
@@ -4245,7 +4314,7 @@
 	if (mddev->pers) {
 		if (mddev->pers->check_reshape == NULL)
 			err = -EBUSY;
-		else if (mddev->ro)
+		else if (!md_is_rdwr(mddev))
 			err = -EROFS;
 		else {
 			mddev->new_chunk_sectors = n >> 9;
@@ -4342,10 +4411,9 @@
  *     like active, but no writes have been seen for a while (100msec).
  *
  * broken
- *     RAID0/LINEAR-only: same as clean, but array is missing a member.
- *     It's useful because RAID0/LINEAR mounted-arrays aren't stopped
- *     when a member is gone, so this state will at least alert the
- *     user that something is wrong.
+*     Array is failed. It's useful because mounted-arrays aren't stopped
+*     when array is failed, so this state will at least alert the user that
+*     something is wrong.
  */
 enum array_state { clear, inactive, suspended, readonly, read_auto, clean, active,
 		   write_pending, active_idle, broken, bad_word};
@@ -4369,13 +4437,13 @@
 
 	if (mddev->pers && !test_bit(MD_NOT_READY, &mddev->flags)) {
 		switch(mddev->ro) {
-		case 1:
+		case MD_RDONLY:
 			st = readonly;
 			break;
-		case 2:
+		case MD_AUTO_READ:
 			st = read_auto;
 			break;
-		case 0:
+		case MD_RDWR:
 			spin_lock(&mddev->lock);
 			if (test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags))
 				st = write_pending;
@@ -4411,7 +4479,8 @@
 	int err = 0;
 	enum array_state st = match_word(buf, array_states);
 
-	if (mddev->pers && (st == active || st == clean) && mddev->ro != 1) {
+	if (mddev->pers && (st == active || st == clean) &&
+	    mddev->ro != MD_RDONLY) {
 		/* don't take reconfig_mutex when toggling between
 		 * clean and active
 		 */
@@ -4455,23 +4524,23 @@
 		if (mddev->pers)
 			err = md_set_readonly(mddev, NULL);
 		else {
-			mddev->ro = 1;
+			mddev->ro = MD_RDONLY;
 			set_disk_ro(mddev->gendisk, 1);
 			err = do_md_run(mddev);
 		}
 		break;
 	case read_auto:
 		if (mddev->pers) {
-			if (mddev->ro == 0)
+			if (md_is_rdwr(mddev))
 				err = md_set_readonly(mddev, NULL);
-			else if (mddev->ro == 1)
+			else if (mddev->ro == MD_RDONLY)
 				err = restart_array(mddev);
 			if (err == 0) {
-				mddev->ro = 2;
+				mddev->ro = MD_AUTO_READ;
 				set_disk_ro(mddev->gendisk, 0);
 			}
 		} else {
-			mddev->ro = 2;
+			mddev->ro = MD_AUTO_READ;
 			err = do_md_run(mddev);
 		}
 		break;
@@ -4496,7 +4565,7 @@
 			wake_up(&mddev->sb_wait);
 			err = 0;
 		} else {
-			mddev->ro = 0;
+			mddev->ro = MD_RDWR;
 			set_disk_ro(mddev->gendisk, 0);
 			err = do_md_run(mddev);
 		}
@@ -4534,6 +4603,8 @@
 	rv = kstrtouint(buf, 10, &n);
 	if (rv < 0)
 		return rv;
+	if (n > INT_MAX)
+		return -EINVAL;
 	atomic_set(&mddev->max_corr_read_errors, n);
 	return len;
 }
@@ -4795,7 +4866,7 @@
 	if (test_bit(MD_RECOVERY_FROZEN, &recovery))
 		type = "frozen";
 	else if (test_bit(MD_RECOVERY_RUNNING, &recovery) ||
-	    (!mddev->ro && test_bit(MD_RECOVERY_NEEDED, &recovery))) {
+	    (md_is_rdwr(mddev) && test_bit(MD_RECOVERY_NEEDED, &recovery))) {
 		if (test_bit(MD_RECOVERY_RESHAPE, &recovery))
 			type = "reshape";
 		else if (test_bit(MD_RECOVERY_SYNC, &recovery)) {
@@ -4848,11 +4919,21 @@
 			return -EINVAL;
 		err = mddev_lock(mddev);
 		if (!err) {
-			if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery))
+			if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery)) {
 				err =  -EBUSY;
-			else {
+			} else if (mddev->reshape_position == MaxSector ||
+				   mddev->pers->check_reshape == NULL ||
+				   mddev->pers->check_reshape(mddev)) {
 				clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
 				err = mddev->pers->start_reshape(mddev);
+			} else {
+				/*
+				 * If reshape is still in progress, and
+				 * md_check_recovery() can continue to reshape,
+				 * don't restart reshape because data can be
+				 * corrupted for raid456.
+				 */
+				clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
 			}
 			mddev_unlock(mddev);
 		}
@@ -4868,11 +4949,11 @@
 		set_bit(MD_RECOVERY_REQUESTED, &mddev->recovery);
 		set_bit(MD_RECOVERY_SYNC, &mddev->recovery);
 	}
-	if (mddev->ro == 2) {
+	if (mddev->ro == MD_AUTO_READ) {
 		/* A write to sync_action is enough to justify
 		 * canceling read-auto mode
 		 */
-		mddev->ro = 0;
+		mddev->ro = MD_RDWR;
 		md_wakeup_thread(mddev->sync_thread);
 	}
 	set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
@@ -5100,8 +5181,7 @@
 			goto out_unlock;
 
 		err = -EBUSY;
-		if (max < mddev->resync_max &&
-		    mddev->ro == 0 &&
+		if (max < mddev->resync_max && md_is_rdwr(mddev) &&
 		    test_bit(MD_RECOVERY_RUNNING, &mddev->recovery))
 			goto out_unlock;
 
@@ -5575,8 +5655,6 @@
 
 	bioset_exit(&mddev->bio_set);
 	bioset_exit(&mddev->sync_set);
-	if (mddev->level != 1 && mddev->level != 10)
-		bioset_exit(&mddev->io_acct_set);
 	kfree(mddev);
 }
 
@@ -5640,6 +5718,7 @@
 	 * removed (mddev_delayed_delete).
 	 */
 	flush_workqueue(md_misc_wq);
+	flush_workqueue(md_rdev_misc_wq);
 
 	mutex_lock(&disks_mutex);
 	mddev = mddev_alloc(dev);
@@ -5818,8 +5897,8 @@
 			continue;
 		sync_blockdev(rdev->bdev);
 		invalidate_bdev(rdev->bdev);
-		if (mddev->ro != 1 && rdev_read_only(rdev)) {
-			mddev->ro = 1;
+		if (mddev->ro != MD_RDONLY && rdev_read_only(rdev)) {
+			mddev->ro = MD_RDONLY;
 			if (mddev->gendisk)
 				set_disk_ro(mddev->gendisk, 1);
 		}
@@ -5862,13 +5941,6 @@
 		if (err)
 			goto exit_bio_set;
 	}
-	if (mddev->level != 1 && mddev->level != 10 &&
-	    !bioset_initialized(&mddev->io_acct_set)) {
-		err = bioset_init(&mddev->io_acct_set, BIO_POOL_SIZE,
-				  offsetof(struct md_io_acct, bio_clone), 0);
-		if (err)
-			goto exit_sync_set;
-	}
 
 	spin_lock(&pers_lock);
 	pers = find_pers(mddev->level, mddev->clevel);
@@ -5929,8 +6001,8 @@
 
 	mddev->ok_start_degraded = start_dirty_degraded;
 
-	if (start_readonly && mddev->ro == 0)
-		mddev->ro = 2; /* read-only, but switch on first write */
+	if (start_readonly && md_is_rdwr(mddev))
+		mddev->ro = MD_AUTO_READ; /* read-only, but switch on first write */
 
 	err = pers->run(mddev);
 	if (err)
@@ -6005,8 +6077,8 @@
 		mddev->sysfs_action = sysfs_get_dirent_safe(mddev->kobj.sd, "sync_action");
 		mddev->sysfs_completed = sysfs_get_dirent_safe(mddev->kobj.sd, "sync_completed");
 		mddev->sysfs_degraded = sysfs_get_dirent_safe(mddev->kobj.sd, "degraded");
-	} else if (mddev->ro == 2) /* auto-readonly not meaningful */
-		mddev->ro = 0;
+	} else if (mddev->ro == MD_AUTO_READ)
+		mddev->ro = MD_RDWR;
 
 	atomic_set(&mddev->max_corr_read_errors,
 		   MD_DEFAULT_MAX_CORRECTED_READ_ERRORS);
@@ -6024,7 +6096,7 @@
 		if (rdev->raid_disk >= 0)
 			sysfs_link_rdev(mddev, rdev); /* failure here is OK */
 
-	if (mddev->degraded && !mddev->ro)
+	if (mddev->degraded && md_is_rdwr(mddev))
 		/* This ensures that recovering status is reported immediately
 		 * via sysfs - until a lack of spares is confirmed.
 		 */
@@ -6045,9 +6117,6 @@
 	module_put(pers->owner);
 	md_bitmap_destroy(mddev);
 abort:
-	if (mddev->level != 1 && mddev->level != 10)
-		bioset_exit(&mddev->io_acct_set);
-exit_sync_set:
 	bioset_exit(&mddev->sync_set);
 exit_bio_set:
 	bioset_exit(&mddev->bio_set);
@@ -6117,7 +6186,7 @@
 		return -ENXIO;
 	if (!mddev->pers)
 		return -EINVAL;
-	if (!mddev->ro)
+	if (md_is_rdwr(mddev))
 		return -EBUSY;
 
 	rcu_read_lock();
@@ -6136,7 +6205,7 @@
 		return -EROFS;
 
 	mddev->safemode = 0;
-	mddev->ro = 0;
+	mddev->ro = MD_RDWR;
 	set_disk_ro(disk, 0);
 	pr_debug("md: %s switched to read-write mode.\n", mdname(mddev));
 	/* Kick recovery or resync if necessary */
@@ -6161,9 +6230,17 @@
 	mddev->persistent = 0;
 	mddev->level = LEVEL_NONE;
 	mddev->clevel[0] = 0;
-	mddev->flags = 0;
+	/*
+	 * Don't clear MD_CLOSING, or mddev can be opened again.
+	 * 'hold_active != 0' means mddev is still in the creation
+	 * process and will be used later.
+	 */
+	if (mddev->hold_active)
+		mddev->flags = 0;
+	else
+		mddev->flags &= BIT_ULL_MASK(MD_CLOSING);
 	mddev->sb_flags = 0;
-	mddev->ro = 0;
+	mddev->ro = MD_RDWR;
 	mddev->metadata_type[0] = 0;
 	mddev->chunk_sectors = 0;
 	mddev->ctime = mddev->utime = 0;
@@ -6214,7 +6291,7 @@
 	}
 	md_bitmap_flush(mddev);
 
-	if (mddev->ro == 0 &&
+	if (md_is_rdwr(mddev) &&
 	    ((!mddev->in_sync && !mddev_is_clustered(mddev)) ||
 	     mddev->sb_flags)) {
 		/* mark array as shutdown cleanly */
@@ -6268,14 +6345,15 @@
 
 void md_stop(struct mddev *mddev)
 {
+	lockdep_assert_held(&mddev->reconfig_mutex);
+
 	/* stop the array and free an attached data structures.
 	 * This is called from dm-raid
 	 */
+	__md_stop_writes(mddev);
 	__md_stop(mddev);
 	bioset_exit(&mddev->bio_set);
 	bioset_exit(&mddev->sync_set);
-	if (mddev->level != 1 && mddev->level != 10)
-		bioset_exit(&mddev->io_acct_set);
 }
 
 EXPORT_SYMBOL_GPL(md_stop);
@@ -6285,6 +6363,9 @@
 	int err = 0;
 	int did_freeze = 0;
 
+	if (mddev->external && test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags))
+		return -EBUSY;
+
 	if (!test_bit(MD_RECOVERY_FROZEN, &mddev->recovery)) {
 		did_freeze = 1;
 		set_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
@@ -6297,8 +6378,6 @@
 		 * which will now never happen */
 		wake_up_process(mddev->sync_thread->tsk);
 
-	if (mddev->external && test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags))
-		return -EBUSY;
 	mddev_unlock(mddev);
 	wait_event(resync_wait, !test_bit(MD_RECOVERY_RUNNING,
 					  &mddev->recovery));
@@ -6311,29 +6390,30 @@
 	    mddev->sync_thread ||
 	    test_bit(MD_RECOVERY_RUNNING, &mddev->recovery)) {
 		pr_warn("md: %s still in use.\n",mdname(mddev));
-		if (did_freeze) {
-			clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
-			set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
-			md_wakeup_thread(mddev->thread);
-		}
 		err = -EBUSY;
 		goto out;
 	}
+
 	if (mddev->pers) {
 		__md_stop_writes(mddev);
 
-		err  = -ENXIO;
-		if (mddev->ro==1)
+		if (mddev->ro == MD_RDONLY) {
+			err  = -ENXIO;
 			goto out;
-		mddev->ro = 1;
+		}
+
+		mddev->ro = MD_RDONLY;
 		set_disk_ro(mddev->gendisk, 1);
+	}
+
+out:
+	if ((mddev->pers && !err) || did_freeze) {
 		clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
 		set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
 		md_wakeup_thread(mddev->thread);
 		sysfs_notify_dirent_safe(mddev->sysfs_state);
-		err = 0;
 	}
-out:
+
 	mutex_unlock(&mddev->open_mutex);
 	return err;
 }
@@ -6382,7 +6462,7 @@
 		return -EBUSY;
 	}
 	if (mddev->pers) {
-		if (mddev->ro)
+		if (!md_is_rdwr(mddev))
 			set_disk_ro(disk, 0);
 
 		__md_stop_writes(mddev);
@@ -6399,8 +6479,8 @@
 		mutex_unlock(&mddev->open_mutex);
 		mddev->changed = 1;
 
-		if (mddev->ro)
-			mddev->ro = 0;
+		if (!md_is_rdwr(mddev))
+			mddev->ro = MD_RDWR;
 	} else
 		mutex_unlock(&mddev->open_mutex);
 	/*
@@ -6767,7 +6847,7 @@
 			rdev->saved_raid_disk = rdev->raid_disk;
 		} else
 			super_types[mddev->major_version].
-				validate_super(mddev, rdev);
+				validate_super(mddev, NULL/*freshest*/, rdev);
 		if ((info->state & (1<<MD_DISK_SYNC)) &&
 		     rdev->raid_disk != info->raid_disk) {
 			/* This was a hot-add request, but events doesn't
@@ -7212,7 +7292,7 @@
 	if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery) ||
 	    mddev->sync_thread)
 		return -EBUSY;
-	if (mddev->ro)
+	if (!md_is_rdwr(mddev))
 		return -EROFS;
 
 	rdev_for_each(rdev, mddev) {
@@ -7242,7 +7322,7 @@
 	/* change the number of raid disks */
 	if (mddev->pers->check_reshape == NULL)
 		return -EINVAL;
-	if (mddev->ro)
+	if (!md_is_rdwr(mddev))
 		return -EROFS;
 	if (raid_disks <= 0 ||
 	    (mddev->max_disks && raid_disks >= mddev->max_disks))
@@ -7425,7 +7505,7 @@
 		err =  -ENODEV;
 	else {
 		md_error(mddev, rdev);
-		if (!test_bit(Faulty, &rdev->flags))
+		if (test_bit(MD_BROKEN, &mddev->flags))
 			err = -EBUSY;
 	}
 	rcu_read_unlock();
@@ -7478,7 +7558,6 @@
 	int err = 0;
 	void __user *argp = (void __user *)arg;
 	struct mddev *mddev = NULL;
-	bool did_set_md_closing = false;
 
 	if (!md_ioctl_valid(cmd))
 		return -ENOTTY;
@@ -7510,11 +7589,6 @@
 
 	mddev = bdev->bd_disk->private_data;
 
-	if (!mddev) {
-		BUG();
-		goto out;
-	}
-
 	/* Some actions do not requires the mutex */
 	switch (cmd) {
 	case GET_ARRAY_INFO:
@@ -7565,7 +7639,6 @@
 			err = -EBUSY;
 			goto out;
 		}
-		did_set_md_closing = true;
 		mutex_unlock(&mddev->open_mutex);
 		sync_blockdev(bdev);
 	}
@@ -7666,26 +7739,25 @@
 	 * The remaining ioctls are changing the state of the
 	 * superblock, so we do not allow them on read-only arrays.
 	 */
-	if (mddev->ro && mddev->pers) {
-		if (mddev->ro == 2) {
-			mddev->ro = 0;
-			sysfs_notify_dirent_safe(mddev->sysfs_state);
-			set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
-			/* mddev_unlock will wake thread */
-			/* If a device failed while we were read-only, we
-			 * need to make sure the metadata is updated now.
-			 */
-			if (test_bit(MD_SB_CHANGE_DEVS, &mddev->sb_flags)) {
-				mddev_unlock(mddev);
-				wait_event(mddev->sb_wait,
-					   !test_bit(MD_SB_CHANGE_DEVS, &mddev->sb_flags) &&
-					   !test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags));
-				mddev_lock_nointr(mddev);
-			}
-		} else {
+	if (!md_is_rdwr(mddev) && mddev->pers) {
+		if (mddev->ro != MD_AUTO_READ) {
 			err = -EROFS;
 			goto unlock;
 		}
+		mddev->ro = MD_RDWR;
+		sysfs_notify_dirent_safe(mddev->sysfs_state);
+		set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
+		/* mddev_unlock will wake thread */
+		/* If a device failed while we were read-only, we
+		 * need to make sure the metadata is updated now.
+		 */
+		if (test_bit(MD_SB_CHANGE_DEVS, &mddev->sb_flags)) {
+			mddev_unlock(mddev);
+			wait_event(mddev->sb_wait,
+				   !test_bit(MD_SB_CHANGE_DEVS, &mddev->sb_flags) &&
+				   !test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags));
+			mddev_lock_nointr(mddev);
+		}
 	}
 
 	switch (cmd) {
@@ -7729,7 +7801,7 @@
 		mddev->hold_active = 0;
 	mddev_unlock(mddev);
 out:
-	if(did_set_md_closing)
+	if (cmd == STOP_ARRAY_RO || (err && cmd == STOP_ARRAY))
 		clear_bit(MD_CLOSING, &mddev->flags);
 	return err;
 }
@@ -7771,11 +7843,11 @@
 	 * Transitioning to read-auto need only happen for arrays that call
 	 * md_write_start and which are not ready for writes yet.
 	 */
-	if (!ro && mddev->ro == 1 && mddev->pers) {
+	if (!ro && mddev->ro == MD_RDONLY && mddev->pers) {
 		err = restart_array(mddev);
 		if (err)
 			goto out_unlock;
-		mddev->ro = 2;
+		mddev->ro = MD_AUTO_READ;
 	}
 
 out_unlock:
@@ -7943,17 +8015,22 @@
 
 void md_unregister_thread(struct md_thread **threadp)
 {
-	struct md_thread *thread = *threadp;
-	if (!thread)
-		return;
-	pr_debug("interrupting MD-thread pid %d\n", task_pid_nr(thread->tsk));
-	/* Locking ensures that mddev_unlock does not wake_up a
+	struct md_thread *thread;
+
+	/*
+	 * Locking ensures that mddev_unlock does not wake_up a
 	 * non-existent thread
 	 */
 	spin_lock(&pers_lock);
+	thread = *threadp;
+	if (!thread) {
+		spin_unlock(&pers_lock);
+		return;
+	}
 	*threadp = NULL;
 	spin_unlock(&pers_lock);
 
+	pr_debug("interrupting MD-thread pid %d\n", task_pid_nr(thread->tsk));
 	kthread_stop(thread->tsk);
 	kfree(thread);
 }
@@ -7966,13 +8043,19 @@
 
 	if (!mddev->pers || !mddev->pers->error_handler)
 		return;
-	mddev->pers->error_handler(mddev,rdev);
-	if (mddev->degraded)
+	mddev->pers->error_handler(mddev, rdev);
+
+	if (mddev->pers->level == 0 || mddev->pers->level == LEVEL_LINEAR)
+		return;
+
+	if (mddev->degraded && !test_bit(MD_BROKEN, &mddev->flags))
 		set_bit(MD_RECOVERY_RECOVER, &mddev->recovery);
 	sysfs_notify_dirent_safe(rdev->sysfs_state);
 	set_bit(MD_RECOVERY_INTR, &mddev->recovery);
-	set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
-	md_wakeup_thread(mddev->thread);
+	if (!test_bit(MD_BROKEN, &mddev->flags)) {
+		set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
+		md_wakeup_thread(mddev->thread);
+	}
 	if (mddev->event_work.func)
 		queue_work(md_misc_wq, &mddev->event_work);
 	md_new_event(mddev);
@@ -8222,9 +8305,9 @@
 		seq_printf(seq, "%s : %sactive", mdname(mddev),
 						mddev->pers ? "" : "in");
 		if (mddev->pers) {
-			if (mddev->ro==1)
+			if (mddev->ro == MD_RDONLY)
 				seq_printf(seq, " (read-only)");
-			if (mddev->ro==2)
+			if (mddev->ro == MD_AUTO_READ)
 				seq_printf(seq, " (auto-read-only)");
 			seq_printf(seq, " %s", mddev->pers->name);
 		}
@@ -8484,10 +8567,10 @@
 	if (bio_data_dir(bi) != WRITE)
 		return true;
 
-	BUG_ON(mddev->ro == 1);
-	if (mddev->ro == 2) {
+	BUG_ON(mddev->ro == MD_RDONLY);
+	if (mddev->ro == MD_AUTO_READ) {
 		/* need to switch to read/write */
-		mddev->ro = 0;
+		mddev->ro = MD_RDWR;
 		set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
 		md_wakeup_thread(mddev->thread);
 		md_wakeup_thread(mddev->sync_thread);
@@ -8538,7 +8621,7 @@
 {
 	if (bio_data_dir(bi) != WRITE)
 		return;
-	WARN_ON_ONCE(mddev->in_sync || mddev->ro);
+	WARN_ON_ONCE(mddev->in_sync || !md_is_rdwr(mddev));
 	percpu_ref_get(&mddev->writes_pending);
 }
 EXPORT_SYMBOL(md_write_inc);
@@ -8580,12 +8663,30 @@
 }
 EXPORT_SYMBOL_GPL(md_submit_discard_bio);
 
+int acct_bioset_init(struct mddev *mddev)
+{
+	int err = 0;
+
+	if (!bioset_initialized(&mddev->io_acct_set))
+		err = bioset_init(&mddev->io_acct_set, BIO_POOL_SIZE,
+			offsetof(struct md_io_acct, bio_clone), 0);
+	return err;
+}
+EXPORT_SYMBOL_GPL(acct_bioset_init);
+
+void acct_bioset_exit(struct mddev *mddev)
+{
+	bioset_exit(&mddev->io_acct_set);
+}
+EXPORT_SYMBOL_GPL(acct_bioset_exit);
+
 static void md_end_io_acct(struct bio *bio)
 {
 	struct md_io_acct *md_io_acct = bio->bi_private;
 	struct bio *orig_bio = md_io_acct->orig_bio;
 
-	orig_bio->bi_status = bio->bi_status;
+	if (bio->bi_status && !orig_bio->bi_status)
+		orig_bio->bi_status = bio->bi_status;
 
 	bio_end_io_acct(orig_bio, md_io_acct->start_time);
 	bio_put(bio);
@@ -8625,7 +8726,7 @@
 {
 	if (!mddev->pers)
 		return;
-	if (mddev->ro)
+	if (!md_is_rdwr(mddev))
 		return;
 	if (!mddev->pers->sync_request)
 		return;
@@ -8674,7 +8775,7 @@
 	if (test_bit(MD_RECOVERY_DONE, &mddev->recovery) ||
 	    test_bit(MD_RECOVERY_WAIT, &mddev->recovery))
 		return;
-	if (mddev->ro) {/* never try to sync a read-only array */
+	if (!md_is_rdwr(mddev)) {/* never try to sync a read-only array */
 		set_bit(MD_RECOVERY_INTR, &mddev->recovery);
 		return;
 	}
@@ -9142,9 +9243,9 @@
 		if (test_bit(Faulty, &rdev->flags))
 			continue;
 		if (!test_bit(Journal, &rdev->flags)) {
-			if (mddev->ro &&
-			    ! (rdev->saved_raid_disk >= 0 &&
-			       !test_bit(Bitmap_sync, &rdev->flags)))
+			if (!md_is_rdwr(mddev) &&
+			    !(rdev->saved_raid_disk >= 0 &&
+			      !test_bit(Bitmap_sync, &rdev->flags)))
 				continue;
 
 			rdev->recovery_offset = 0;
@@ -9242,7 +9343,8 @@
 		flush_signals(current);
 	}
 
-	if (mddev->ro && !test_bit(MD_RECOVERY_NEEDED, &mddev->recovery))
+	if (!md_is_rdwr(mddev) &&
+	    !test_bit(MD_RECOVERY_NEEDED, &mddev->recovery))
 		return;
 	if ( ! (
 		(mddev->sb_flags & ~ (1<<MD_SB_CHANGE_PENDING)) ||
@@ -9261,7 +9363,7 @@
 		if (!mddev->external && mddev->safemode == 1)
 			mddev->safemode = 0;
 
-		if (mddev->ro) {
+		if (!md_is_rdwr(mddev)) {
 			struct md_rdev *rdev;
 			if (!mddev->external && mddev->in_sync)
 				/* 'Blocked' flag not needed as failed devices
@@ -9446,6 +9548,7 @@
 	wake_up(&resync_wait);
 	/* flag recovery needed just to double check */
 	set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
+	sysfs_notify_dirent_safe(mddev->sysfs_completed);
 	sysfs_notify_dirent_safe(mddev->sysfs_action);
 	md_new_event(mddev);
 	if (mddev->event_work.func)
@@ -9754,16 +9857,18 @@
 
 void md_reload_sb(struct mddev *mddev, int nr)
 {
-	struct md_rdev *rdev;
+	struct md_rdev *rdev = NULL, *iter;
 	int err;
 
 	/* Find the rdev */
-	rdev_for_each_rcu(rdev, mddev) {
-		if (rdev->desc_nr == nr)
+	rdev_for_each_rcu(iter, mddev) {
+		if (iter->desc_nr == nr) {
+			rdev = iter;
 			break;
+		}
 	}
 
-	if (!rdev || rdev->desc_nr != nr) {
+	if (!rdev) {
 		pr_warn("%s: %d Could not find rdev with nr %d\n", __func__, __LINE__, nr);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/md.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/md.h
@@ -234,34 +234,42 @@
 				int is_new);
 struct md_cluster_info;
 
-/* change UNSUPPORTED_MDDEV_FLAGS for each array type if new flag is added */
+/**
+ * enum mddev_flags - md device flags.
+ * @MD_ARRAY_FIRST_USE: First use of array, needs initialization.
+ * @MD_CLOSING: If set, we are closing the array, do not open it then.
+ * @MD_JOURNAL_CLEAN: A raid with journal is already clean.
+ * @MD_HAS_JOURNAL: The raid array has journal feature set.
+ * @MD_CLUSTER_RESYNC_LOCKED: cluster raid only, which means node, already took
+ *			       resync lock, need to release the lock.
+ * @MD_FAILFAST_SUPPORTED: Using MD_FAILFAST on metadata writes is supported as
+ *			    calls to md_error() will never cause the array to
+ *			    become failed.
+ * @MD_HAS_PPL:  The raid array has PPL feature set.
+ * @MD_HAS_MULTIPLE_PPLS: The raid array has multiple PPLs feature set.
+ * @MD_ALLOW_SB_UPDATE: md_check_recovery is allowed to update the metadata
+ *			 without taking reconfig_mutex.
+ * @MD_UPDATING_SB: md_check_recovery is updating the metadata without
+ *		     explicitly holding reconfig_mutex.
+ * @MD_NOT_READY: do_md_run() is active, so 'array_state', ust not report that
+ *		   array is ready yet.
+ * @MD_BROKEN: This is used to stop writes and mark array as failed.
+ *
+ * change UNSUPPORTED_MDDEV_FLAGS for each array type if new flag is added
+ */
 enum mddev_flags {
-	MD_ARRAY_FIRST_USE,	/* First use of array, needs initialization */
-	MD_CLOSING,		/* If set, we are closing the array, do not open
-				 * it then */
-	MD_JOURNAL_CLEAN,	/* A raid with journal is already clean */
-	MD_HAS_JOURNAL,		/* The raid array has journal feature set */
-	MD_CLUSTER_RESYNC_LOCKED, /* cluster raid only, which means node
-				   * already took resync lock, need to
-				   * release the lock */
-	MD_FAILFAST_SUPPORTED,	/* Using MD_FAILFAST on metadata writes is
-				 * supported as calls to md_error() will
-				 * never cause the array to become failed.
-				 */
-	MD_HAS_PPL,		/* The raid array has PPL feature set */
-	MD_HAS_MULTIPLE_PPLS,	/* The raid array has multiple PPLs feature set */
-	MD_ALLOW_SB_UPDATE,	/* md_check_recovery is allowed to update
-				 * the metadata without taking reconfig_mutex.
-				 */
-	MD_UPDATING_SB,		/* md_check_recovery is updating the metadata
-				 * without explicitly holding reconfig_mutex.
-				 */
-	MD_NOT_READY,		/* do_md_run() is active, so 'array_state'
-				 * must not report that array is ready yet
-				 */
-	MD_BROKEN,              /* This is used in RAID-0/LINEAR only, to stop
-				 * I/O in case an array member is gone/failed.
-				 */
+	MD_ARRAY_FIRST_USE,
+	MD_CLOSING,
+	MD_JOURNAL_CLEAN,
+	MD_HAS_JOURNAL,
+	MD_CLUSTER_RESYNC_LOCKED,
+	MD_FAILFAST_SUPPORTED,
+	MD_HAS_PPL,
+	MD_HAS_MULTIPLE_PPLS,
+	MD_ALLOW_SB_UPDATE,
+	MD_UPDATING_SB,
+	MD_NOT_READY,
+	MD_BROKEN,
 };
 
 enum mddev_sb_flags {
@@ -721,6 +729,8 @@
 extern void md_finish_reshape(struct mddev *mddev);
 void md_submit_discard_bio(struct mddev *mddev, struct md_rdev *rdev,
 			struct bio *bio, sector_t start, sector_t size);
+int acct_bioset_init(struct mddev *mddev);
+void acct_bioset_exit(struct mddev *mddev);
 void md_account_bio(struct mddev *mddev, struct bio **bio);
 
 extern bool __must_check md_flush_request(struct mddev *mddev, struct bio *bio);
@@ -762,15 +772,9 @@
 struct md_rdev *md_find_rdev_nr_rcu(struct mddev *mddev, int nr);
 struct md_rdev *md_find_rdev_rcu(struct mddev *mddev, dev_t dev);
 
-static inline bool is_mddev_broken(struct md_rdev *rdev, const char *md_type)
+static inline bool is_rdev_broken(struct md_rdev *rdev)
 {
-	if (!disk_live(rdev->bdev->bd_disk)) {
-		if (!test_and_set_bit(MD_BROKEN, &rdev->mddev->flags))
-			pr_warn("md: %s: %s array has a missing/failed member\n",
-				mdname(rdev->mddev), md_type);
-		return true;
-	}
-	return false;
+	return !disk_live(rdev->bdev->bd_disk);
 }
 
 static inline void rdev_dec_pending(struct md_rdev *rdev, struct mddev *mddev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/persistent-data/dm-array.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/persistent-data/dm-array.c
@@ -911,23 +911,27 @@
 	if (c->block)
 		unlock_ablock(c->info, c->block);
 
-	c->block = NULL;
-	c->ab = NULL;
 	c->index = 0;
 
 	r = dm_btree_cursor_get_value(&c->cursor, &key, &value_le);
 	if (r) {
 		DMERR("dm_btree_cursor_get_value failed");
-		dm_btree_cursor_end(&c->cursor);
+		goto out;
 
 	} else {
 		r = get_ablock(c->info, le64_to_cpu(value_le), &c->block, &c->ab);
 		if (r) {
 			DMERR("get_ablock failed");
-			dm_btree_cursor_end(&c->cursor);
+			goto out;
 		}
 	}
 
+	return 0;
+
+out:
+	dm_btree_cursor_end(&c->cursor);
+	c->block = NULL;
+	c->ab = NULL;
 	return r;
 }
 
@@ -950,10 +954,10 @@
 
 void dm_array_cursor_end(struct dm_array_cursor *c)
 {
-	if (c->block) {
+	if (c->block)
 		unlock_ablock(c->info, c->block);
-		dm_btree_cursor_end(&c->cursor);
-	}
+
+	dm_btree_cursor_end(&c->cursor);
 }
 EXPORT_SYMBOL_GPL(dm_array_cursor_end);
 
@@ -993,6 +997,7 @@
 		}
 
 		count -= remaining;
+		c->index += (remaining - 1);
 		r = dm_array_cursor_next(c);
 
 	} while (!r);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/persistent-data/dm-btree-remove.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/persistent-data/dm-btree-remove.c
@@ -423,9 +423,9 @@
 
 		memcpy(n, dm_block_data(child),
 		       dm_bm_block_size(dm_tm_get_bm(info->tm)));
-		dm_tm_unlock(info->tm, child);
 
 		dm_tm_dec(info->tm, dm_block_location(child));
+		dm_tm_unlock(info->tm, child);
 		return 0;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/persistent-data/dm-btree.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/persistent-data/dm-btree.c
@@ -81,14 +81,16 @@
 }
 
 static int insert_at(size_t value_size, struct btree_node *node, unsigned index,
-		      uint64_t key, void *value)
-		      __dm_written_to_disk(value)
+		     uint64_t key, void *value)
+	__dm_written_to_disk(value)
 {
 	uint32_t nr_entries = le32_to_cpu(node->header.nr_entries);
+	uint32_t max_entries = le32_to_cpu(node->header.max_entries);
 	__le64 key_le = cpu_to_le64(key);
 
 	if (index > nr_entries ||
-	    index >= le32_to_cpu(node->header.max_entries)) {
+	    index >= max_entries ||
+	    nr_entries >= max_entries) {
 		DMERR("too many entries in btree node for insert");
 		__dm_unbless_for_disk(value);
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/persistent-data/dm-space-map-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/persistent-data/dm-space-map-common.c
@@ -283,6 +283,11 @@
 	struct disk_index_entry ie_disk;
 	struct dm_block *blk;
 
+	if (b >= ll->nr_blocks) {
+		DMERR_LIMIT("metadata block out of bounds");
+		return -EINVAL;
+	}
+
 	b = do_div(index, ll->entries_per_block);
 	r = ll->load_ie(ll, index, &ie_disk);
 	if (r < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/persistent-data/dm-space-map-metadata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/persistent-data/dm-space-map-metadata.c
@@ -274,7 +274,7 @@
 {
 	struct sm_metadata *smm = container_of(sm, struct sm_metadata, sm);
 
-	kfree(smm);
+	kvfree(smm);
 }
 
 static int sm_metadata_get_nr_blocks(struct dm_space_map *sm, dm_block_t *count)
@@ -768,7 +768,7 @@
 {
 	struct sm_metadata *smm;
 
-	smm = kmalloc(sizeof(*smm), GFP_KERNEL);
+	smm = kvmalloc(sizeof(*smm), GFP_KERNEL);
 	if (!smm)
 		return ERR_PTR(-ENOMEM);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/raid0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/raid0.c
@@ -48,7 +48,7 @@
 		int len = 0;
 
 		for (k = 0; k < conf->strip_zone[j].nb_dev; k++)
-			len += snprintf(line+len, 200-len, "%s%s", k?"/":"",
+			len += scnprintf(line+len, 200-len, "%s%s", k?"/":"",
 					bdevname(conf->devlist[j*raid_disks
 							       + k]->bdev, b));
 		pr_debug("md: zone%d=[%s]\n", j, line);
@@ -128,21 +128,6 @@
 	pr_debug("md/raid0:%s: FINAL %d zones\n",
 		 mdname(mddev), conf->nr_strip_zones);
 
-	if (conf->nr_strip_zones == 1) {
-		conf->layout = RAID0_ORIG_LAYOUT;
-	} else if (mddev->layout == RAID0_ORIG_LAYOUT ||
-		   mddev->layout == RAID0_ALT_MULTIZONE_LAYOUT) {
-		conf->layout = mddev->layout;
-	} else if (default_layout == RAID0_ORIG_LAYOUT ||
-		   default_layout == RAID0_ALT_MULTIZONE_LAYOUT) {
-		conf->layout = default_layout;
-	} else {
-		pr_err("md/raid0:%s: cannot assemble multi-zone RAID0 with default_layout setting\n",
-		       mdname(mddev));
-		pr_err("md/raid0: please set raid0.default_layout to 1 or 2\n");
-		err = -ENOTSUPP;
-		goto abort;
-	}
 	/*
 	 * now since we have the hard sector sizes, we can make sure
 	 * chunk size is a multiple of that sector size
@@ -273,6 +258,36 @@
 			 (unsigned long long)smallest->sectors);
 	}
 
+	if (conf->nr_strip_zones == 1 || conf->strip_zone[1].nb_dev == 1) {
+		conf->layout = RAID0_ORIG_LAYOUT;
+	} else if (mddev->layout == RAID0_ORIG_LAYOUT ||
+		   mddev->layout == RAID0_ALT_MULTIZONE_LAYOUT) {
+		conf->layout = mddev->layout;
+	} else if (default_layout == RAID0_ORIG_LAYOUT ||
+		   default_layout == RAID0_ALT_MULTIZONE_LAYOUT) {
+		conf->layout = default_layout;
+	} else {
+		pr_err("md/raid0:%s: cannot assemble multi-zone RAID0 with default_layout setting\n",
+		       mdname(mddev));
+		pr_err("md/raid0: please set raid0.default_layout to 1 or 2\n");
+		pr_err("md/raid0: Read the following page for more information:\n");
+		pr_err("md/raid0: https://wiki.ubuntu.com/Kernel/Raid0LayoutMigration\n");
+		err = -EOPNOTSUPP;
+		goto abort;
+	}
+
+	if (conf->layout == RAID0_ORIG_LAYOUT) {
+		for (i = 1; i < conf->nr_strip_zones; i++) {
+			sector_t first_sector = conf->strip_zone[i-1].zone_end;
+
+			sector_div(first_sector, mddev->chunk_sectors);
+			zone = conf->strip_zone + i;
+			/* disk_shift is first disk index used in the zone */
+			zone->disk_shift = sector_div(first_sector,
+						      zone->nb_dev);
+		}
+	}
+
 	pr_debug("md/raid0:%s: done.\n", mdname(mddev));
 	*private_conf = conf;
 
@@ -356,7 +371,20 @@
 	return array_sectors;
 }
 
-static void raid0_free(struct mddev *mddev, void *priv);
+static void free_conf(struct mddev *mddev, struct r0conf *conf)
+{
+	kfree(conf->strip_zone);
+	kfree(conf->devlist);
+	kfree(conf);
+}
+
+static void raid0_free(struct mddev *mddev, void *priv)
+{
+	struct r0conf *conf = priv;
+
+	free_conf(mddev, conf);
+	acct_bioset_exit(mddev);
+}
 
 static int raid0_run(struct mddev *mddev)
 {
@@ -370,11 +398,16 @@
 	if (md_check_no_bitmap(mddev))
 		return -EINVAL;
 
+	if (acct_bioset_init(mddev)) {
+		pr_err("md/raid0:%s: alloc acct bioset failed.\n", mdname(mddev));
+		return -ENOMEM;
+	}
+
 	/* if private is not null, we are here after takeover */
 	if (mddev->private == NULL) {
 		ret = create_strip_zones(mddev, &conf);
 		if (ret < 0)
-			return ret;
+			goto exit_acct_set;
 		mddev->private = conf;
 	}
 	conf = mddev->private;
@@ -413,17 +446,30 @@
 	dump_zones(mddev);
 
 	ret = md_integrity_register(mddev);
+	if (ret)
+		goto free;
+
+	return ret;
 
+free:
+	free_conf(mddev, conf);
+exit_acct_set:
+	acct_bioset_exit(mddev);
 	return ret;
 }
 
-static void raid0_free(struct mddev *mddev, void *priv)
+/*
+ * Convert disk_index to the disk order in which it is read/written.
+ *  For example, if we have 4 disks, they are numbered 0,1,2,3. If we
+ *  write the disks starting at disk 3, then the read/write order would
+ *  be disk 3, then 0, then 1, and then disk 2 and we want map_disk_shift()
+ *  to map the disks as follows 0,1,2,3 => 1,2,3,0. So disk 0 would map
+ *  to 1, 1 to 2, 2 to 3, and 3 to 0. That way we can compare disks in
+ *  that 'output' space to understand the read/write disk ordering.
+ */
+static int map_disk_shift(int disk_index, int num_disks, int disk_shift)
 {
-	struct r0conf *conf = priv;
-
-	kfree(conf->strip_zone);
-	kfree(conf->devlist);
-	kfree(conf);
+	return ((disk_index + num_disks - disk_shift) % num_disks);
 }
 
 static void raid0_handle_discard(struct mddev *mddev, struct bio *bio)
@@ -439,7 +485,9 @@
 	sector_t end_disk_offset;
 	unsigned int end_disk_index;
 	unsigned int disk;
+	sector_t orig_start, orig_end;
 
+	orig_start = start;
 	zone = find_zone(conf, &start);
 
 	if (bio_end_sector(bio) > zone->zone_end) {
@@ -453,6 +501,7 @@
 	} else
 		end = bio_end_sector(bio);
 
+	orig_end = end;
 	if (zone != conf->strip_zone)
 		end = end - zone[-1].zone_end;
 
@@ -464,13 +513,26 @@
 	last_stripe_index = end;
 	sector_div(last_stripe_index, stripe_size);
 
-	start_disk_index = (int)(start - first_stripe_index * stripe_size) /
-		mddev->chunk_sectors;
+	/* In the first zone the original and alternate layouts are the same */
+	if ((conf->layout == RAID0_ORIG_LAYOUT) && (zone != conf->strip_zone)) {
+		sector_div(orig_start, mddev->chunk_sectors);
+		start_disk_index = sector_div(orig_start, zone->nb_dev);
+		start_disk_index = map_disk_shift(start_disk_index,
+						  zone->nb_dev,
+						  zone->disk_shift);
+		sector_div(orig_end, mddev->chunk_sectors);
+		end_disk_index = sector_div(orig_end, zone->nb_dev);
+		end_disk_index = map_disk_shift(end_disk_index,
+						zone->nb_dev, zone->disk_shift);
+	} else {
+		start_disk_index = (int)(start - first_stripe_index * stripe_size) /
+			mddev->chunk_sectors;
+		end_disk_index = (int)(end - last_stripe_index * stripe_size) /
+			mddev->chunk_sectors;
+	}
 	start_disk_offset = ((int)(start - first_stripe_index * stripe_size) %
 		mddev->chunk_sectors) +
 		first_stripe_index * mddev->chunk_sectors;
-	end_disk_index = (int)(end - last_stripe_index * stripe_size) /
-		mddev->chunk_sectors;
 	end_disk_offset = ((int)(end - last_stripe_index * stripe_size) %
 		mddev->chunk_sectors) +
 		last_stripe_index * mddev->chunk_sectors;
@@ -478,18 +540,22 @@
 	for (disk = 0; disk < zone->nb_dev; disk++) {
 		sector_t dev_start, dev_end;
 		struct md_rdev *rdev;
+		int compare_disk;
+
+		compare_disk = map_disk_shift(disk, zone->nb_dev,
+					      zone->disk_shift);
 
-		if (disk < start_disk_index)
+		if (compare_disk < start_disk_index)
 			dev_start = (first_stripe_index + 1) *
 				mddev->chunk_sectors;
-		else if (disk > start_disk_index)
+		else if (compare_disk > start_disk_index)
 			dev_start = first_stripe_index * mddev->chunk_sectors;
 		else
 			dev_start = start_disk_offset;
 
-		if (disk < end_disk_index)
+		if (compare_disk < end_disk_index)
 			dev_end = (last_stripe_index + 1) * mddev->chunk_sectors;
-		else if (disk > end_disk_index)
+		else if (compare_disk > end_disk_index)
 			dev_end = last_stripe_index * mddev->chunk_sectors;
 		else
 			dev_end = end_disk_offset;
@@ -506,54 +572,20 @@
 	bio_endio(bio);
 }
 
-static bool raid0_make_request(struct mddev *mddev, struct bio *bio)
+static void raid0_map_submit_bio(struct mddev *mddev, struct bio *bio)
 {
 	struct r0conf *conf = mddev->private;
 	struct strip_zone *zone;
 	struct md_rdev *tmp_dev;
-	sector_t bio_sector;
-	sector_t sector;
-	sector_t orig_sector;
-	unsigned chunk_sects;
-	unsigned sectors;
-
-	if (unlikely(bio->bi_opf & REQ_PREFLUSH)
-	    && md_flush_request(mddev, bio))
-		return true;
-
-	if (unlikely((bio_op(bio) == REQ_OP_DISCARD))) {
-		raid0_handle_discard(mddev, bio);
-		return true;
-	}
+	sector_t bio_sector = bio->bi_iter.bi_sector;
+	sector_t sector = bio_sector;
 
-	bio_sector = bio->bi_iter.bi_sector;
-	sector = bio_sector;
-	chunk_sects = mddev->chunk_sectors;
-
-	sectors = chunk_sects -
-		(likely(is_power_of_2(chunk_sects))
-		 ? (sector & (chunk_sects-1))
-		 : sector_div(sector, chunk_sects));
+	md_account_bio(mddev, &bio);
 
-	/* Restore due to sector_div */
-	sector = bio_sector;
-
-	if (sectors < bio_sectors(bio)) {
-		struct bio *split = bio_split(bio, sectors, GFP_NOIO,
-					      &mddev->bio_set);
-		bio_chain(split, bio);
-		submit_bio_noacct(bio);
-		bio = split;
-	}
-
-	if (bio->bi_pool != &mddev->bio_set)
-		md_account_bio(mddev, &bio);
-
-	orig_sector = sector;
 	zone = find_zone(mddev->private, &sector);
 	switch (conf->layout) {
 	case RAID0_ORIG_LAYOUT:
-		tmp_dev = map_sector(mddev, zone, orig_sector, &sector);
+		tmp_dev = map_sector(mddev, zone, bio_sector, &sector);
 		break;
 	case RAID0_ALT_MULTIZONE_LAYOUT:
 		tmp_dev = map_sector(mddev, zone, sector, &sector);
@@ -561,12 +593,13 @@
 	default:
 		WARN(1, "md/raid0:%s: Invalid layout\n", mdname(mddev));
 		bio_io_error(bio);
-		return true;
+		return;
 	}
 
-	if (unlikely(is_mddev_broken(tmp_dev, "raid0"))) {
+	if (unlikely(is_rdev_broken(tmp_dev))) {
 		bio_io_error(bio);
-		return true;
+		md_error(mddev, tmp_dev);
+		return;
 	}
 
 	bio_set_dev(bio, tmp_dev->bdev);
@@ -579,6 +612,40 @@
 	mddev_check_writesame(mddev, bio);
 	mddev_check_write_zeroes(mddev, bio);
 	submit_bio_noacct(bio);
+}
+
+static bool raid0_make_request(struct mddev *mddev, struct bio *bio)
+{
+	sector_t sector;
+	unsigned chunk_sects;
+	unsigned sectors;
+
+	if (unlikely(bio->bi_opf & REQ_PREFLUSH)
+	    && md_flush_request(mddev, bio))
+		return true;
+
+	if (unlikely((bio_op(bio) == REQ_OP_DISCARD))) {
+		raid0_handle_discard(mddev, bio);
+		return true;
+	}
+
+	sector = bio->bi_iter.bi_sector;
+	chunk_sects = mddev->chunk_sectors;
+
+	sectors = chunk_sects -
+		(likely(is_power_of_2(chunk_sects))
+		 ? (sector & (chunk_sects-1))
+		 : sector_div(sector, chunk_sects));
+
+	if (sectors < bio_sectors(bio)) {
+		struct bio *split = bio_split(bio, sectors, GFP_NOIO,
+					      &mddev->bio_set);
+		bio_chain(split, bio);
+		raid0_map_submit_bio(mddev, bio);
+		bio = split;
+	}
+
+	raid0_map_submit_bio(mddev, bio);
 	return true;
 }
 
@@ -588,6 +655,16 @@
 	return;
 }
 
+static void raid0_error(struct mddev *mddev, struct md_rdev *rdev)
+{
+	if (!test_and_set_bit(MD_BROKEN, &mddev->flags)) {
+		char *md_name = mdname(mddev);
+
+		pr_crit("md/raid0%s: Disk failure on %pg detected, failing array.\n",
+			md_name, rdev->bdev);
+	}
+}
+
 static void *raid0_takeover_raid45(struct mddev *mddev)
 {
 	struct md_rdev *rdev;
@@ -763,6 +840,7 @@
 	.size		= raid0_size,
 	.takeover	= raid0_takeover,
 	.quiesce	= raid0_quiesce,
+	.error_handler	= raid0_error,
 };
 
 static int __init raid0_init (void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/raid0.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/raid0.h
@@ -6,6 +6,7 @@
 	sector_t zone_end;	/* Start of the next zone (in sectors) */
 	sector_t dev_start;	/* Zone offset in real dev (in sectors) */
 	int	 nb_dev;	/* # of devices attached to the zone */
+	int	 disk_shift;	/* start disk for the original layout */
 };
 
 /* Linux 3.14 (20d0189b101) made an unintended change to
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/raid1-10.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/raid1-10.c
@@ -22,12 +22,6 @@
 
 #define BIO_SPECIAL(bio) ((unsigned long)bio <= 2)
 
-/* When there are this many requests queue to be written by
- * the raid thread, we become 'congested' to provide back-pressure
- * for writeback.
- */
-static int max_queued_requests = 1024;
-
 /* for managing resync I/O pages */
 struct resync_pages {
 	void		*raid_bio;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/raid1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/raid1.c
@@ -1358,12 +1358,6 @@
 	r1_bio = alloc_r1bio(mddev, bio);
 	r1_bio->sectors = max_write_sectors;
 
-	if (conf->pending_count >= max_queued_requests) {
-		md_wakeup_thread(mddev->thread);
-		raid1_log(mddev, "wait queued");
-		wait_event(conf->wait_barrier,
-			   conf->pending_count < max_queued_requests);
-	}
 	/* first select target devices under rcu_lock and
 	 * inc refcount on their rdev.  Record them by setting
 	 * bios[x] to bio
@@ -1502,6 +1496,7 @@
 			 * allocate memory, or a reader on WriteMostly
 			 * is waiting for behind writes to flush */
 			if (bitmap &&
+			    test_bit(WriteMostly, &rdev->flags) &&
 			    (atomic_read(&bitmap->behind_writes)
 			     < mddev->bitmap_info.max_write_behind) &&
 			    !waitqueue_active(&bitmap->behind_wait)) {
@@ -1616,30 +1611,39 @@
 	seq_printf(seq, "]");
 }
 
+/**
+ * raid1_error() - RAID1 error handler.
+ * @mddev: affected md device.
+ * @rdev: member device to fail.
+ *
+ * The routine acknowledges &rdev failure and determines new @mddev state.
+ * If it failed, then:
+ *	- &MD_BROKEN flag is set in &mddev->flags.
+ *	- recovery is disabled.
+ * Otherwise, it must be degraded:
+ *	- recovery is interrupted.
+ *	- &mddev->degraded is bumped.
+ *
+ * @rdev is marked as &Faulty excluding case when array is failed and
+ * &mddev->fail_last_dev is off.
+ */
 static void raid1_error(struct mddev *mddev, struct md_rdev *rdev)
 {
 	char b[BDEVNAME_SIZE];
 	struct r1conf *conf = mddev->private;
 	unsigned long flags;
 
-	/*
-	 * If it is not operational, then we have already marked it as dead
-	 * else if it is the last working disks with "fail_last_dev == false",
-	 * ignore the error, let the next level up know.
-	 * else mark the drive as failed
-	 */
 	spin_lock_irqsave(&conf->device_lock, flags);
-	if (test_bit(In_sync, &rdev->flags) && !mddev->fail_last_dev
-	    && (conf->raid_disks - mddev->degraded) == 1) {
-		/*
-		 * Don't fail the drive, act as though we were just a
-		 * normal single drive.
-		 * However don't try a recovery from this drive as
-		 * it is very likely to fail.
-		 */
-		conf->recovery_disabled = mddev->recovery_disabled;
-		spin_unlock_irqrestore(&conf->device_lock, flags);
-		return;
+
+	if (test_bit(In_sync, &rdev->flags) &&
+	    (conf->raid_disks - mddev->degraded) == 1) {
+		set_bit(MD_BROKEN, &mddev->flags);
+
+		if (!mddev->fail_last_dev) {
+			conf->recovery_disabled = mddev->recovery_disabled;
+			spin_unlock_irqrestore(&conf->device_lock, flags);
+			return;
+		}
 	}
 	set_bit(Blocked, &rdev->flags);
 	if (test_and_clear_bit(In_sync, &rdev->flags))
@@ -1818,6 +1822,9 @@
 	int number = rdev->raid_disk;
 	struct raid1_info *p = conf->mirrors + number;
 
+	if (unlikely(number >= conf->raid_disks))
+		goto abort;
+
 	if (rdev != p->rdev)
 		p = conf->mirrors + conf->raid_disks + number;
 
@@ -3140,6 +3147,7 @@
 	 * RAID1 needs at least one disk in active
 	 */
 	if (conf->raid_disks - mddev->degraded < 1) {
+		md_unregister_thread(&conf->thread);
 		ret = -EINVAL;
 		goto abort;
 	}
@@ -3411,4 +3419,3 @@
 MODULE_ALIAS("md-raid1");
 MODULE_ALIAS("md-level-1");
 
-module_param(max_queued_requests, int, S_IRUGO|S_IWUSR);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/raid10.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/raid10.c
@@ -297,7 +297,7 @@
 	if (!test_bit(R10BIO_Uptodate, &r10_bio->state))
 		bio->bi_status = BLK_STS_IOERR;
 
-	if (blk_queue_io_stat(bio->bi_bdev->bd_disk->queue))
+	if (r10_bio->start_time)
 		bio_end_io_acct(bio, r10_bio->start_time);
 	bio_endio(bio);
 	/*
@@ -752,8 +752,16 @@
 		disk = r10_bio->devs[slot].devnum;
 		rdev = rcu_dereference(conf->mirrors[disk].replacement);
 		if (rdev == NULL || test_bit(Faulty, &rdev->flags) ||
-		    r10_bio->devs[slot].addr + sectors > rdev->recovery_offset)
+		    r10_bio->devs[slot].addr + sectors >
+		    rdev->recovery_offset) {
+			/*
+			 * Read replacement first to prevent reading both rdev
+			 * and replacement as NULL during replacement replace
+			 * rdev.
+			 */
+			smp_mb();
 			rdev = rcu_dereference(conf->mirrors[disk].rdev);
+		}
 		if (rdev == NULL ||
 		    test_bit(Faulty, &rdev->flags))
 			continue;
@@ -895,6 +903,7 @@
 			else
 				submit_bio_noacct(bio);
 			bio = next;
+			cond_resched();
 		}
 		blk_finish_plug(&plug);
 	} else
@@ -952,42 +961,62 @@
 	wake_up(&conf->wait_barrier);
 }
 
-static void wait_barrier(struct r10conf *conf)
+static bool stop_waiting_barrier(struct r10conf *conf)
+{
+	struct bio_list *bio_list = current->bio_list;
+
+	/* barrier is dropped */
+	if (!conf->barrier)
+		return true;
+
+	/*
+	 * If there are already pending requests (preventing the barrier from
+	 * rising completely), and the pre-process bio queue isn't empty, then
+	 * don't wait, as we need to empty that queue to get the nr_pending
+	 * count down.
+	 */
+	if (atomic_read(&conf->nr_pending) && bio_list &&
+	    (!bio_list_empty(&bio_list[0]) || !bio_list_empty(&bio_list[1])))
+		return true;
+
+	/*
+	 * move on if io is issued from raid10d(), nr_pending is not released
+	 * from original io(see handle_read_error()). All raise barrier is
+	 * blocked until this io is done.
+	 */
+	if (conf->mddev->thread->tsk == current) {
+		WARN_ON_ONCE(atomic_read(&conf->nr_pending) == 0);
+		return true;
+	}
+
+	return false;
+}
+
+static bool wait_barrier(struct r10conf *conf, bool nowait)
 {
+	bool ret = true;
+
 	spin_lock_irq(&conf->resync_lock);
 	if (conf->barrier) {
-		struct bio_list *bio_list = current->bio_list;
 		conf->nr_waiting++;
-		/* Wait for the barrier to drop.
-		 * However if there are already pending
-		 * requests (preventing the barrier from
-		 * rising completely), and the
-		 * pre-process bio queue isn't empty,
-		 * then don't wait, as we need to empty
-		 * that queue to get the nr_pending
-		 * count down.
-		 */
-		raid10_log(conf->mddev, "wait barrier");
-		wait_event_lock_irq(conf->wait_barrier,
-				    !conf->barrier ||
-				    (atomic_read(&conf->nr_pending) &&
-				     bio_list &&
-				     (!bio_list_empty(&bio_list[0]) ||
-				      !bio_list_empty(&bio_list[1]))) ||
-				     /* move on if recovery thread is
-				      * blocked by us
-				      */
-				     (conf->mddev->thread->tsk == current &&
-				      test_bit(MD_RECOVERY_RUNNING,
-					       &conf->mddev->recovery) &&
-				      conf->nr_queued > 0),
-				    conf->resync_lock);
+		/* Return false when nowait flag is set */
+		if (nowait) {
+			ret = false;
+		} else {
+			raid10_log(conf->mddev, "wait barrier");
+			wait_event_lock_irq(conf->wait_barrier,
+					    stop_waiting_barrier(conf),
+					    conf->resync_lock);
+		}
 		conf->nr_waiting--;
 		if (!conf->nr_waiting)
 			wake_up(&conf->wait_barrier);
 	}
-	atomic_inc(&conf->nr_pending);
+	/* Only increment nr_pending when we wait */
+	if (ret)
+		atomic_inc(&conf->nr_pending);
 	spin_unlock_irq(&conf->resync_lock);
+	return ret;
 }
 
 static void allow_barrier(struct r10conf *conf)
@@ -1088,6 +1117,7 @@
 		else
 			submit_bio_noacct(bio);
 		bio = next;
+		cond_resched();
 	}
 	kfree(plug);
 }
@@ -1098,21 +1128,30 @@
  * currently.
  * 2. If IO spans the reshape position.  Need to wait for reshape to pass.
  */
-static void regular_request_wait(struct mddev *mddev, struct r10conf *conf,
+static bool regular_request_wait(struct mddev *mddev, struct r10conf *conf,
 				 struct bio *bio, sector_t sectors)
 {
-	wait_barrier(conf);
+	/* Bail out if REQ_NOWAIT is set for the bio */
+	if (!wait_barrier(conf, bio->bi_opf & REQ_NOWAIT)) {
+		bio_wouldblock_error(bio);
+		return false;
+	}
 	while (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery) &&
 	    bio->bi_iter.bi_sector < conf->reshape_progress &&
 	    bio->bi_iter.bi_sector + sectors > conf->reshape_progress) {
-		raid10_log(conf->mddev, "wait reshape");
 		allow_barrier(conf);
+		if (bio->bi_opf & REQ_NOWAIT) {
+			bio_wouldblock_error(bio);
+			return false;
+		}
+		raid10_log(conf->mddev, "wait reshape");
 		wait_event(conf->wait_barrier,
 			   conf->reshape_progress <= bio->bi_iter.bi_sector ||
 			   conf->reshape_progress >= bio->bi_iter.bi_sector +
 			   sectors);
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 	}
+	return true;
 }
 
 static void raid10_read_request(struct mddev *mddev, struct bio *bio,
@@ -1157,7 +1196,8 @@
 		rcu_read_unlock();
 	}
 
-	regular_request_wait(mddev, conf, bio, r10_bio->sectors);
+	if (!regular_request_wait(mddev, conf, bio, r10_bio->sectors))
+		return;
 	rdev = read_balance(conf, r10_bio, &max_sectors);
 	if (!rdev) {
 		if (err_rdev) {
@@ -1179,14 +1219,15 @@
 		bio_chain(split, bio);
 		allow_barrier(conf);
 		submit_bio_noacct(bio);
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 		bio = split;
 		r10_bio->master_bio = bio;
 		r10_bio->sectors = max_sectors;
 	}
 	slot = r10_bio->read_slot;
 
-	if (blk_queue_io_stat(bio->bi_bdev->bd_disk->queue))
+	if (!r10_bio->start_time &&
+	    blk_queue_io_stat(bio->bi_bdev->bd_disk->queue))
 		r10_bio->start_time = bio_start_io_acct(bio);
 	read_bio = bio_clone_fast(bio, gfp, &mddev->bio_set);
 
@@ -1277,6 +1318,25 @@
 	}
 }
 
+static struct md_rdev *dereference_rdev_and_rrdev(struct raid10_info *mirror,
+						  struct md_rdev **prrdev)
+{
+	struct md_rdev *rdev, *rrdev;
+
+	rrdev = rcu_dereference(mirror->replacement);
+	/*
+	 * Read replacement first to prevent reading both rdev and
+	 * replacement as NULL during replacement replace rdev.
+	 */
+	smp_mb();
+	rdev = rcu_dereference(mirror->rdev);
+	if (rdev == rrdev)
+		rrdev = NULL;
+
+	*prrdev = rrdev;
+	return rdev;
+}
+
 static void wait_blocked_dev(struct mddev *mddev, struct r10bio *r10_bio)
 {
 	int i;
@@ -1287,11 +1347,9 @@
 	blocked_rdev = NULL;
 	rcu_read_lock();
 	for (i = 0; i < conf->copies; i++) {
-		struct md_rdev *rdev = rcu_dereference(conf->mirrors[i].rdev);
-		struct md_rdev *rrdev = rcu_dereference(
-			conf->mirrors[i].replacement);
-		if (rdev == rrdev)
-			rrdev = NULL;
+		struct md_rdev *rdev, *rrdev;
+
+		rdev = dereference_rdev_and_rrdev(&conf->mirrors[i], &rrdev);
 		if (rdev && unlikely(test_bit(Blocked, &rdev->flags))) {
 			atomic_inc(&rdev->nr_pending);
 			blocked_rdev = rdev;
@@ -1338,7 +1396,7 @@
 		raid10_log(conf->mddev, "%s wait rdev %d blocked",
 				__func__, blocked_rdev->raid_disk);
 		md_wait_for_blocked_rdev(blocked_rdev, mddev);
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 		goto retry_wait;
 	}
 }
@@ -1356,6 +1414,11 @@
 					    bio->bi_iter.bi_sector,
 					    bio_end_sector(bio)))) {
 		DEFINE_WAIT(w);
+		/* Bail out if REQ_NOWAIT is set for the bio */
+		if (bio->bi_opf & REQ_NOWAIT) {
+			bio_wouldblock_error(bio);
+			return;
+		}
 		for (;;) {
 			prepare_to_wait(&conf->wait_barrier,
 					&w, TASK_IDLE);
@@ -1368,7 +1431,8 @@
 	}
 
 	sectors = r10_bio->sectors;
-	regular_request_wait(mddev, conf, bio, sectors);
+	if (!regular_request_wait(mddev, conf, bio, sectors))
+		return;
 	if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery) &&
 	    (mddev->reshape_backwards
 	     ? (bio->bi_iter.bi_sector < conf->reshape_safe &&
@@ -1380,6 +1444,11 @@
 		set_mask_bits(&mddev->sb_flags, 0,
 			      BIT(MD_SB_CHANGE_DEVS) | BIT(MD_SB_CHANGE_PENDING));
 		md_wakeup_thread(mddev->thread);
+		if (bio->bi_opf & REQ_NOWAIT) {
+			allow_barrier(conf);
+			bio_wouldblock_error(bio);
+			return;
+		}
 		raid10_log(conf->mddev, "wait reshape metadata");
 		wait_event(mddev->sb_wait,
 			   !test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags));
@@ -1387,12 +1456,6 @@
 		conf->reshape_safe = mddev->reshape_position;
 	}
 
-	if (conf->pending_count >= max_queued_requests) {
-		md_wakeup_thread(mddev->thread);
-		raid10_log(mddev, "wait queued");
-		wait_event(conf->wait_barrier,
-			   conf->pending_count < max_queued_requests);
-	}
 	/* first select target devices under rcu_lock and
 	 * inc refcount on their rdev.  Record them by setting
 	 * bios[x] to bio
@@ -1413,11 +1476,9 @@
 
 	for (i = 0;  i < conf->copies; i++) {
 		int d = r10_bio->devs[i].devnum;
-		struct md_rdev *rdev = rcu_dereference(conf->mirrors[d].rdev);
-		struct md_rdev *rrdev = rcu_dereference(
-			conf->mirrors[d].replacement);
-		if (rdev == rrdev)
-			rrdev = NULL;
+		struct md_rdev *rdev, *rrdev;
+
+		rdev = dereference_rdev_and_rrdev(&conf->mirrors[d], &rrdev);
 		if (rdev && (test_bit(Faulty, &rdev->flags)))
 			rdev = NULL;
 		if (rrdev && (test_bit(Faulty, &rrdev->flags)))
@@ -1482,7 +1543,7 @@
 		bio_chain(split, bio);
 		allow_barrier(conf);
 		submit_bio_noacct(bio);
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 		bio = split;
 		r10_bio->master_bio = bio;
 	}
@@ -1515,6 +1576,7 @@
 	r10_bio->sector = bio->bi_iter.bi_sector;
 	r10_bio->state = 0;
 	r10_bio->read_slot = -1;
+	r10_bio->start_time = 0;
 	memset(r10_bio->devs, 0, sizeof(r10_bio->devs[0]) *
 			conf->geo.raid_disks);
 
@@ -1607,7 +1669,11 @@
 	if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery))
 		return -EAGAIN;
 
-	wait_barrier(conf);
+	if (WARN_ON_ONCE(bio->bi_opf & REQ_NOWAIT)) {
+		bio_wouldblock_error(bio);
+		return 0;
+	}
+	wait_barrier(conf, false);
 
 	/*
 	 * Check reshape again to avoid reshape happens after checking
@@ -1649,7 +1715,7 @@
 		allow_barrier(conf);
 		/* Resend the fist split part */
 		submit_bio_noacct(split);
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 	}
 	div_u64_rem(bio_end, stripe_size, &remainder);
 	if (remainder) {
@@ -1660,7 +1726,7 @@
 		/* Resend the second split part */
 		submit_bio_noacct(bio);
 		bio = split;
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 	}
 
 	bio_start = bio->bi_iter.bi_sector;
@@ -1719,10 +1785,9 @@
 	 */
 	rcu_read_lock();
 	for (disk = 0; disk < geo->raid_disks; disk++) {
-		struct md_rdev *rdev = rcu_dereference(conf->mirrors[disk].rdev);
-		struct md_rdev *rrdev = rcu_dereference(
-			conf->mirrors[disk].replacement);
+		struct md_rdev *rdev, *rrdev;
 
+		rdev = dereference_rdev_and_rrdev(&conf->mirrors[disk], &rrdev);
 		r10_bio->devs[disk].bio = NULL;
 		r10_bio->devs[disk].repl_bio = NULL;
 
@@ -1816,7 +1881,7 @@
 		end_disk_offset += geo->stride;
 		atomic_inc(&first_r10bio->remaining);
 		raid_end_discard_bio(r10_bio);
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 		goto retry_discard;
 	}
 
@@ -1945,32 +2010,40 @@
 		_enough(conf, 1, ignore);
 }
 
+/**
+ * raid10_error() - RAID10 error handler.
+ * @mddev: affected md device.
+ * @rdev: member device to fail.
+ *
+ * The routine acknowledges &rdev failure and determines new @mddev state.
+ * If it failed, then:
+ *	- &MD_BROKEN flag is set in &mddev->flags.
+ * Otherwise, it must be degraded:
+ *	- recovery is interrupted.
+ *	- &mddev->degraded is bumped.
+
+ * @rdev is marked as &Faulty excluding case when array is failed and
+ * &mddev->fail_last_dev is off.
+ */
 static void raid10_error(struct mddev *mddev, struct md_rdev *rdev)
 {
 	char b[BDEVNAME_SIZE];
 	struct r10conf *conf = mddev->private;
 	unsigned long flags;
 
-	/*
-	 * If it is not operational, then we have already marked it as dead
-	 * else if it is the last working disks with "fail_last_dev == false",
-	 * ignore the error, let the next level up know.
-	 * else mark the drive as failed
-	 */
 	spin_lock_irqsave(&conf->device_lock, flags);
-	if (test_bit(In_sync, &rdev->flags) && !mddev->fail_last_dev
-	    && !enough(conf, rdev->raid_disk)) {
-		/*
-		 * Don't fail the drive, just return an IO error.
-		 */
-		spin_unlock_irqrestore(&conf->device_lock, flags);
-		return;
+
+	if (test_bit(In_sync, &rdev->flags) && !enough(conf, rdev->raid_disk)) {
+		set_bit(MD_BROKEN, &mddev->flags);
+
+		if (!mddev->fail_last_dev) {
+			spin_unlock_irqrestore(&conf->device_lock, flags);
+			return;
+		}
 	}
 	if (test_and_clear_bit(In_sync, &rdev->flags))
 		mddev->degraded++;
-	/*
-	 * If recovery is running, make sure it aborts.
-	 */
+
 	set_bit(MD_RECOVERY_INTR, &mddev->recovery);
 	set_bit(Blocked, &rdev->flags);
 	set_bit(Faulty, &rdev->flags);
@@ -2011,7 +2084,7 @@
 
 static void close_sync(struct r10conf *conf)
 {
-	wait_barrier(conf);
+	wait_barrier(conf, false);
 	allow_barrier(conf);
 
 	mempool_exit(&conf->r10buf_pool);
@@ -2139,9 +2212,12 @@
 	int err = 0;
 	int number = rdev->raid_disk;
 	struct md_rdev **rdevp;
-	struct raid10_info *p = conf->mirrors + number;
+	struct raid10_info *p;
 
 	print_conf(conf);
+	if (unlikely(number >= mddev->raid_disks))
+		return 0;
+	p = conf->mirrors + number;
 	if (rdev == p->rdev)
 		rdevp = &p->rdev;
 	else if (rdev == p->replacement)
@@ -2539,11 +2615,22 @@
 {
 	struct r10conf *conf = mddev->private;
 	int d;
-	struct bio *wbio, *wbio2;
+	struct bio *wbio = r10_bio->devs[1].bio;
+	struct bio *wbio2 = r10_bio->devs[1].repl_bio;
+
+	/* Need to test wbio2->bi_end_io before we call
+	 * submit_bio_noacct as if the former is NULL,
+	 * the latter is free to free wbio2.
+	 */
+	if (wbio2 && !wbio2->bi_end_io)
+		wbio2 = NULL;
 
 	if (!test_bit(R10BIO_Uptodate, &r10_bio->state)) {
 		fix_recovery_read_error(r10_bio);
-		end_sync_request(r10_bio);
+		if (wbio->bi_end_io)
+			end_sync_request(r10_bio);
+		if (wbio2)
+			end_sync_request(r10_bio);
 		return;
 	}
 
@@ -2552,14 +2639,6 @@
 	 * and submit the write request
 	 */
 	d = r10_bio->devs[1].devnum;
-	wbio = r10_bio->devs[1].bio;
-	wbio2 = r10_bio->devs[1].repl_bio;
-	/* Need to test wbio2->bi_end_io before we call
-	 * submit_bio_noacct as if the former is NULL,
-	 * the latter is free to free wbio2.
-	 */
-	if (wbio2 && !wbio2->bi_end_io)
-		wbio2 = NULL;
 	if (wbio->bi_end_io) {
 		atomic_inc(&conf->mirrors[d].rdev->nr_pending);
 		md_sync_acct(conf->mirrors[d].rdev->bdev, bio_sectors(wbio));
@@ -2916,9 +2995,13 @@
 		md_error(mddev, rdev);
 
 	rdev_dec_pending(rdev, mddev);
-	allow_barrier(conf);
 	r10_bio->state = 0;
 	raid10_read_request(mddev, r10_bio->master_bio, r10_bio);
+	/*
+	 * allow_barrier after re-submit to ensure no sync io
+	 * can be issued while regular io pending.
+	 */
+	allow_barrier(conf);
 }
 
 static void handle_write_completed(struct r10conf *conf, struct r10bio *r10_bio)
@@ -3227,10 +3310,6 @@
 	sector_t chunk_mask = conf->geo.chunk_mask;
 	int page_idx = 0;
 
-	if (!mempool_initialized(&conf->r10buf_pool))
-		if (init_resync(conf))
-			return 0;
-
 	/*
 	 * Allow skipping a full rebuild for incremental assembly
 	 * of a clean array, like RAID1 does.
@@ -3246,6 +3325,10 @@
 		return mddev->dev_sectors - sector_nr;
 	}
 
+	if (!mempool_initialized(&conf->r10buf_pool))
+		if (init_resync(conf))
+			return 0;
+
  skipped:
 	max_sector = mddev->dev_sectors;
 	if (test_bit(MD_RECOVERY_SYNC, &mddev->recovery) ||
@@ -3360,8 +3443,6 @@
 			sector_t sect;
 			int must_sync;
 			int any_working;
-			int need_recover = 0;
-			int need_replace = 0;
 			struct raid10_info *mirror = &conf->mirrors[i];
 			struct md_rdev *mrdev, *mreplace;
 
@@ -3369,15 +3450,13 @@
 			mrdev = rcu_dereference(mirror->rdev);
 			mreplace = rcu_dereference(mirror->replacement);
 
-			if (mrdev != NULL &&
-			    !test_bit(Faulty, &mrdev->flags) &&
-			    !test_bit(In_sync, &mrdev->flags))
-				need_recover = 1;
-			if (mreplace != NULL &&
-			    !test_bit(Faulty, &mreplace->flags))
-				need_replace = 1;
+			if (mrdev && (test_bit(Faulty, &mrdev->flags) ||
+			    test_bit(In_sync, &mrdev->flags)))
+				mrdev = NULL;
+			if (mreplace && test_bit(Faulty, &mreplace->flags))
+				mreplace = NULL;
 
-			if (!need_recover && !need_replace) {
+			if (!mrdev && !mreplace) {
 				rcu_read_unlock();
 				continue;
 			}
@@ -3393,8 +3472,6 @@
 				rcu_read_unlock();
 				continue;
 			}
-			if (mreplace && test_bit(Faulty, &mreplace->flags))
-				mreplace = NULL;
 			/* Unless we are doing a full sync, or a replacement
 			 * we only need to recover the block if it is set in
 			 * the bitmap
@@ -3413,7 +3490,8 @@
 				rcu_read_unlock();
 				continue;
 			}
-			atomic_inc(&mrdev->nr_pending);
+			if (mrdev)
+				atomic_inc(&mrdev->nr_pending);
 			if (mreplace)
 				atomic_inc(&mreplace->nr_pending);
 			rcu_read_unlock();
@@ -3500,7 +3578,7 @@
 				r10_bio->devs[1].devnum = i;
 				r10_bio->devs[1].addr = to_addr;
 
-				if (need_recover) {
+				if (mrdev) {
 					bio = r10_bio->devs[1].bio;
 					bio->bi_next = biolist;
 					biolist = bio;
@@ -3517,11 +3595,11 @@
 				bio = r10_bio->devs[1].repl_bio;
 				if (bio)
 					bio->bi_end_io = NULL;
-				/* Note: if need_replace, then bio
+				/* Note: if replace is not NULL, then bio
 				 * cannot be NULL as r10buf_pool_alloc will
 				 * have allocated it.
 				 */
-				if (!need_replace)
+				if (!mreplace)
 					break;
 				bio->bi_next = biolist;
 				biolist = bio;
@@ -3545,7 +3623,7 @@
 					for (k = 0; k < conf->copies; k++)
 						if (r10_bio->devs[k].devnum == i)
 							break;
-					if (!test_bit(In_sync,
+					if (mrdev && !test_bit(In_sync,
 						      &mrdev->flags)
 					    && !rdev_set_badblocks(
 						    mrdev,
@@ -3571,12 +3649,14 @@
 				if (rb2)
 					atomic_dec(&rb2->remaining);
 				r10_bio = rb2;
-				rdev_dec_pending(mrdev, mddev);
+				if (mrdev)
+					rdev_dec_pending(mrdev, mddev);
 				if (mreplace)
 					rdev_dec_pending(mreplace, mddev);
 				break;
 			}
-			rdev_dec_pending(mrdev, mddev);
+			if (mrdev)
+				rdev_dec_pending(mrdev, mddev);
 			if (mreplace)
 				rdev_dec_pending(mreplace, mddev);
 			if (r10_bio->devs[0].bio->bi_opf & MD_FAILFAST) {
@@ -3942,6 +4022,20 @@
 	return nc*fc;
 }
 
+static void raid10_free_conf(struct r10conf *conf)
+{
+	if (!conf)
+		return;
+
+	mempool_exit(&conf->r10bio_pool);
+	kfree(conf->mirrors);
+	kfree(conf->mirrors_old);
+	kfree(conf->mirrors_new);
+	safe_put_page(conf->tmppage);
+	bioset_exit(&conf->bio_split);
+	kfree(conf);
+}
+
 static struct r10conf *setup_conf(struct mddev *mddev)
 {
 	struct r10conf *conf = NULL;
@@ -4024,13 +4118,7 @@
 	return conf;
 
  out:
-	if (conf) {
-		mempool_exit(&conf->r10bio_pool);
-		kfree(conf->mirrors);
-		safe_put_page(conf->tmppage);
-		bioset_exit(&conf->bio_split);
-		kfree(conf);
-	}
+	raid10_free_conf(conf);
 	return ERR_PTR(err);
 }
 
@@ -4068,6 +4156,9 @@
 	if (!conf)
 		goto out;
 
+	mddev->thread = conf->thread;
+	conf->thread = NULL;
+
 	if (mddev_is_clustered(conf->mddev)) {
 		int fc, fo;
 
@@ -4080,9 +4171,6 @@
 		}
 	}
 
-	mddev->thread = conf->thread;
-	conf->thread = NULL;
-
 	if (mddev->queue) {
 		blk_queue_max_discard_sectors(mddev->queue,
 					      UINT_MAX);
@@ -4236,10 +4324,7 @@
 
 out_free_conf:
 	md_unregister_thread(&mddev->thread);
-	mempool_exit(&conf->r10bio_pool);
-	safe_put_page(conf->tmppage);
-	kfree(conf->mirrors);
-	kfree(conf);
+	raid10_free_conf(conf);
 	mddev->private = NULL;
 out:
 	return -EIO;
@@ -4247,15 +4332,7 @@
 
 static void raid10_free(struct mddev *mddev, void *priv)
 {
-	struct r10conf *conf = priv;
-
-	mempool_exit(&conf->r10bio_pool);
-	safe_put_page(conf->tmppage);
-	kfree(conf->mirrors);
-	kfree(conf->mirrors_old);
-	kfree(conf->mirrors_new);
-	bioset_exit(&conf->bio_split);
-	kfree(conf);
+	raid10_free_conf(priv);
 }
 
 static void raid10_quiesce(struct mddev *mddev, int quiesce)
@@ -4819,7 +4896,7 @@
 	if (need_flush ||
 	    time_after(jiffies, conf->reshape_checkpoint + 10*HZ)) {
 		/* Need to update reshape_position in metadata */
-		wait_barrier(conf);
+		wait_barrier(conf, false);
 		mddev->reshape_position = conf->reshape_progress;
 		if (mddev->reshape_backwards)
 			mddev->curr_resync_completed = raid10_size(mddev, 0, 0)
@@ -5242,5 +5319,3 @@
 MODULE_ALIAS("md-personality-9"); /* RAID10 */
 MODULE_ALIAS("md-raid10");
 MODULE_ALIAS("md-level-10");
-
-module_param(max_queued_requests, int, S_IRUGO|S_IWUSR);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/md/raid5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/md/raid5.c
@@ -686,17 +686,17 @@
 	return degraded;
 }
 
-static int has_failed(struct r5conf *conf)
+static bool has_failed(struct r5conf *conf)
 {
-	int degraded;
+	int degraded = conf->mddev->degraded;
 
-	if (conf->mddev->reshape_position == MaxSector)
-		return conf->mddev->degraded > conf->max_degraded;
+	if (test_bit(MD_BROKEN, &conf->mddev->flags))
+		return true;
 
-	degraded = raid5_calc_degraded(conf);
-	if (degraded > conf->max_degraded)
-		return 1;
-	return 0;
+	if (conf->mddev->reshape_position != MaxSector)
+		degraded = raid5_calc_degraded(conf);
+
+	return degraded > conf->max_degraded;
 }
 
 struct stripe_head *
@@ -2349,7 +2349,7 @@
 	atomic_inc(&conf->active_stripes);
 
 	raid5_release_stripe(sh);
-	conf->max_nr_stripes++;
+	WRITE_ONCE(conf->max_nr_stripes, conf->max_nr_stripes + 1);
 	return 1;
 }
 
@@ -2646,7 +2646,7 @@
 	shrink_buffers(sh);
 	free_stripe(conf->slab_cache, sh);
 	atomic_dec(&conf->active_stripes);
-	conf->max_nr_stripes--;
+	WRITE_ONCE(conf->max_nr_stripes, conf->max_nr_stripes - 1);
 	return 1;
 }
 
@@ -2864,10 +2864,10 @@
 	if (!test_and_clear_bit(R5_DOUBLE_LOCKED, &sh->dev[i].flags))
 		clear_bit(R5_LOCKED, &sh->dev[i].flags);
 	set_bit(STRIPE_HANDLE, &sh->state);
-	raid5_release_stripe(sh);
 
 	if (sh->batch_head && sh != sh->batch_head)
 		raid5_release_stripe(sh->batch_head);
+	raid5_release_stripe(sh);
 }
 
 static void raid5_error(struct mddev *mddev, struct md_rdev *rdev)
@@ -2877,34 +2877,31 @@
 	unsigned long flags;
 	pr_debug("raid456: error called\n");
 
+	pr_crit("md/raid:%s: Disk failure on %s, disabling device.\n",
+		mdname(mddev), bdevname(rdev->bdev, b));
+
 	spin_lock_irqsave(&conf->device_lock, flags);
+	set_bit(Faulty, &rdev->flags);
+	clear_bit(In_sync, &rdev->flags);
+	mddev->degraded = raid5_calc_degraded(conf);
 
-	if (test_bit(In_sync, &rdev->flags) &&
-	    mddev->degraded == conf->max_degraded) {
-		/*
-		 * Don't allow to achieve failed state
-		 * Don't try to recover this device
-		 */
+	if (has_failed(conf)) {
+		set_bit(MD_BROKEN, &conf->mddev->flags);
 		conf->recovery_disabled = mddev->recovery_disabled;
-		spin_unlock_irqrestore(&conf->device_lock, flags);
-		return;
+
+		pr_crit("md/raid:%s: Cannot continue operation (%d/%d failed).\n",
+			mdname(mddev), mddev->degraded, conf->raid_disks);
+	} else {
+		pr_crit("md/raid:%s: Operation continuing on %d devices.\n",
+			mdname(mddev), conf->raid_disks - mddev->degraded);
 	}
 
-	set_bit(Faulty, &rdev->flags);
-	clear_bit(In_sync, &rdev->flags);
-	mddev->degraded = raid5_calc_degraded(conf);
 	spin_unlock_irqrestore(&conf->device_lock, flags);
 	set_bit(MD_RECOVERY_INTR, &mddev->recovery);
 
 	set_bit(Blocked, &rdev->flags);
 	set_mask_bits(&mddev->sb_flags, 0,
 		      BIT(MD_SB_CHANGE_DEVS) | BIT(MD_SB_CHANGE_PENDING));
-	pr_crit("md/raid:%s: Disk failure on %s, disabling device.\n"
-		"md/raid:%s: Operation continuing on %d devices.\n",
-		mdname(mddev),
-		bdevname(rdev->bdev, b),
-		mdname(mddev),
-		conf->raid_disks - mddev->degraded);
 	r5c_update_on_rdev_error(mddev, rdev);
 }
 
@@ -3939,7 +3936,7 @@
 		 * back cache (prexor with orig_page, and then xor with
 		 * page) in the read path
 		 */
-		if (s->injournal && s->failed) {
+		if (s->to_read && s->injournal && s->failed) {
 			if (test_bit(STRIPE_R5C_CACHING, &sh->state))
 				r5c_make_stripe_write_out(sh);
 			goto out;
@@ -5410,7 +5407,7 @@
 
 	sector = raid5_compute_sector(conf, raid_bio->bi_iter.bi_sector, 0,
 				      &dd_idx, NULL);
-	end_sector = bio_end_sector(raid_bio);
+	end_sector = sector + bio_sectors(raid_bio);
 
 	rcu_read_lock();
 	if (r5c_big_stripe_cached(conf, sector))
@@ -5433,7 +5430,6 @@
 
 	if (is_badblock(rdev, sector, bio_sectors(raid_bio), &first_bad,
 			&bad_sectors)) {
-		bio_put(raid_bio);
 		rdev_dec_pending(rdev, mddev);
 		return 0;
 	}
@@ -6011,7 +6007,9 @@
 	safepos = conf->reshape_safe;
 	sector_div(safepos, data_disks);
 	if (mddev->reshape_backwards) {
-		BUG_ON(writepos < reshape_sectors);
+		if (WARN_ON(writepos < reshape_sectors))
+			return MaxSector;
+
 		writepos -= reshape_sectors;
 		readpos += reshape_sectors;
 		safepos += reshape_sectors;
@@ -6029,14 +6027,18 @@
 	 * to set 'stripe_addr' which is where we will write to.
 	 */
 	if (mddev->reshape_backwards) {
-		BUG_ON(conf->reshape_progress == 0);
+		if (WARN_ON(conf->reshape_progress == 0))
+			return MaxSector;
+
 		stripe_addr = writepos;
-		BUG_ON((mddev->dev_sectors &
-			~((sector_t)reshape_sectors - 1))
-		       - reshape_sectors - stripe_addr
-		       != sector_nr);
+		if (WARN_ON((mddev->dev_sectors &
+		    ~((sector_t)reshape_sectors - 1)) -
+		    reshape_sectors - stripe_addr != sector_nr))
+			return MaxSector;
 	} else {
-		BUG_ON(writepos != sector_nr + reshape_sectors);
+		if (WARN_ON(writepos != sector_nr + reshape_sectors))
+			return MaxSector;
+
 		stripe_addr = sector_nr;
 	}
 
@@ -6489,6 +6491,9 @@
 		int batch_size, released;
 		unsigned int offset;
 
+		if (test_bit(MD_SB_CHANGE_PENDING, &mddev->sb_flags))
+			break;
+
 		released = release_stripe_list(conf, conf->temp_inactive_list);
 		if (released)
 			clear_bit(R5_DID_ALLOC, &conf->cache_state);
@@ -6572,7 +6577,7 @@
 	if (size <= 16 || size > 32768)
 		return -EINVAL;
 
-	conf->min_nr_stripes = size;
+	WRITE_ONCE(conf->min_nr_stripes, size);
 	mutex_lock(&conf->cache_size_mutex);
 	while (size < conf->max_nr_stripes &&
 	       drop_one_stripe(conf))
@@ -6584,7 +6589,7 @@
 	mutex_lock(&conf->cache_size_mutex);
 	while (size > conf->max_nr_stripes)
 		if (!grow_one_stripe(conf, GFP_KERNEL)) {
-			conf->min_nr_stripes = conf->max_nr_stripes;
+			WRITE_ONCE(conf->min_nr_stripes, conf->max_nr_stripes);
 			result = -ENOMEM;
 			break;
 		}
@@ -7148,11 +7153,13 @@
 				       struct shrink_control *sc)
 {
 	struct r5conf *conf = container_of(shrink, struct r5conf, shrinker);
+	int max_stripes = READ_ONCE(conf->max_nr_stripes);
+	int min_stripes = READ_ONCE(conf->min_nr_stripes);
 
-	if (conf->max_nr_stripes < conf->min_nr_stripes)
+	if (max_stripes < min_stripes)
 		/* unlikely, but not impossible */
 		return 0;
-	return conf->max_nr_stripes - conf->min_nr_stripes;
+	return max_stripes - min_stripes;
 }
 
 static struct r5conf *setup_conf(struct mddev *mddev)
@@ -7446,12 +7453,19 @@
 	struct md_rdev *rdev;
 	struct md_rdev *journal_dev = NULL;
 	sector_t reshape_offset = 0;
-	int i;
+	int i, ret = 0;
 	long long min_offset_diff = 0;
 	int first = 1;
 
-	if (mddev_init_writes_pending(mddev) < 0)
+	if (acct_bioset_init(mddev)) {
+		pr_err("md/raid456:%s: alloc acct bioset failed.\n", mdname(mddev));
 		return -ENOMEM;
+	}
+
+	if (mddev_init_writes_pending(mddev) < 0) {
+		ret = -ENOMEM;
+		goto exit_acct_set;
+	}
 
 	if (mddev->recovery_cp != MaxSector)
 		pr_notice("md/raid:%s: not clean -- starting background reconstruction\n",
@@ -7482,7 +7496,8 @@
 	    (mddev->bitmap_info.offset || mddev->bitmap_info.file)) {
 		pr_notice("md/raid:%s: array cannot have both journal and bitmap\n",
 			  mdname(mddev));
-		return -EINVAL;
+		ret = -EINVAL;
+		goto exit_acct_set;
 	}
 
 	if (mddev->reshape_position != MaxSector) {
@@ -7507,13 +7522,15 @@
 		if (journal_dev) {
 			pr_warn("md/raid:%s: don't support reshape with journal - aborting.\n",
 				mdname(mddev));
-			return -EINVAL;
+			ret = -EINVAL;
+			goto exit_acct_set;
 		}
 
 		if (mddev->new_level != mddev->level) {
 			pr_warn("md/raid:%s: unsupported reshape required - aborting.\n",
 				mdname(mddev));
-			return -EINVAL;
+			ret = -EINVAL;
+			goto exit_acct_set;
 		}
 		old_disks = mddev->raid_disks - mddev->delta_disks;
 		/* reshape_position must be on a new-stripe boundary, and one
@@ -7529,7 +7546,8 @@
 		if (sector_div(here_new, chunk_sectors * new_data_disks)) {
 			pr_warn("md/raid:%s: reshape_position not on a stripe boundary\n",
 				mdname(mddev));
-			return -EINVAL;
+			ret = -EINVAL;
+			goto exit_acct_set;
 		}
 		reshape_offset = here_new * chunk_sectors;
 		/* here_new is the stripe we will write to */
@@ -7551,7 +7569,8 @@
 			else if (mddev->ro == 0) {
 				pr_warn("md/raid:%s: in-place reshape must be started in read-only mode - aborting\n",
 					mdname(mddev));
-				return -EINVAL;
+				ret = -EINVAL;
+				goto exit_acct_set;
 			}
 		} else if (mddev->reshape_backwards
 		    ? (here_new * chunk_sectors + min_offset_diff <=
@@ -7561,7 +7580,8 @@
 			/* Reading from the same stripe as writing to - bad */
 			pr_warn("md/raid:%s: reshape_position too early for auto-recovery - aborting.\n",
 				mdname(mddev));
-			return -EINVAL;
+			ret = -EINVAL;
+			goto exit_acct_set;
 		}
 		pr_debug("md/raid:%s: reshape will continue\n", mdname(mddev));
 		/* OK, we should be able to continue; */
@@ -7585,8 +7605,10 @@
 	else
 		conf = mddev->private;
 
-	if (IS_ERR(conf))
-		return PTR_ERR(conf);
+	if (IS_ERR(conf)) {
+		ret = PTR_ERR(conf);
+		goto exit_acct_set;
+	}
 
 	if (test_bit(MD_HAS_JOURNAL, &mddev->flags)) {
 		if (!journal_dev) {
@@ -7786,7 +7808,10 @@
 	free_conf(conf);
 	mddev->private = NULL;
 	pr_warn("md/raid:%s: failed to run raid set.\n", mdname(mddev));
-	return -EIO;
+	ret = -EIO;
+exit_acct_set:
+	acct_bioset_exit(mddev);
+	return ret;
 }
 
 static void raid5_free(struct mddev *mddev, void *priv)
@@ -7794,6 +7819,7 @@
 	struct r5conf *conf = priv;
 
 	free_conf(conf);
+	acct_bioset_exit(mddev);
 	mddev->to_remove = &raid5_attrs_group;
 }
 
@@ -8010,6 +8036,7 @@
 	 */
 	if (rdev->saved_raid_disk >= 0 &&
 	    rdev->saved_raid_disk >= first &&
+	    rdev->saved_raid_disk <= last &&
 	    conf->disks[rdev->saved_raid_disk].rdev == NULL)
 		first = rdev->saved_raid_disk;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/Kconfig
@@ -141,10 +141,10 @@
 	prompt "Test drivers" if MEDIA_SUPPORT_FILTER
 	default y if !MEDIA_SUPPORT_FILTER
 	help
-	  Those drivers should not be used on production Kernels, but
-	  can be useful on debug ones. It enables several dummy drivers
-	  that simulate a real hardware. Very useful to test userspace
-	  applications and to validate if the subsystem core is doesn't
+	  These drivers should not be used on production kernels, but
+	  can be useful on debug ones. This option enables several dummy drivers
+	  that simulate real hardware. Very useful to test userspace
+	  applications and to validate if the subsystem core doesn't
 	  have regressions.
 
 	  Say Y if you want to use some virtual test driver.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/core/cec-adap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/core/cec-adap.c
@@ -39,15 +39,6 @@
  */
 #define CEC_XFER_TIMEOUT_MS (5 * 400 + 100)
 
-#define call_op(adap, op, arg...) \
-	(adap->ops->op ? adap->ops->op(adap, ## arg) : 0)
-
-#define call_void_op(adap, op, arg...)			\
-	do {						\
-		if (adap->ops->op)			\
-			adap->ops->op(adap, ## arg);	\
-	} while (0)
-
 static int cec_log_addr2idx(const struct cec_adapter *adap, u8 log_addr)
 {
 	int i;
@@ -161,10 +152,10 @@
 	u64 ts = ktime_get_ns();
 	struct cec_fh *fh;
 
-	mutex_lock(&adap->devnode.lock);
+	mutex_lock(&adap->devnode.lock_fhs);
 	list_for_each_entry(fh, &adap->devnode.fhs, list)
 		cec_queue_event_fh(fh, ev, ts);
-	mutex_unlock(&adap->devnode.lock);
+	mutex_unlock(&adap->devnode.lock_fhs);
 }
 
 /* Notify userspace that the CEC pin changed state at the given time. */
@@ -178,11 +169,12 @@
 	};
 	struct cec_fh *fh;
 
-	mutex_lock(&adap->devnode.lock);
-	list_for_each_entry(fh, &adap->devnode.fhs, list)
+	mutex_lock(&adap->devnode.lock_fhs);
+	list_for_each_entry(fh, &adap->devnode.fhs, list) {
 		if (fh->mode_follower == CEC_MODE_MONITOR_PIN)
 			cec_queue_event_fh(fh, &ev, ktime_to_ns(ts));
-	mutex_unlock(&adap->devnode.lock);
+	}
+	mutex_unlock(&adap->devnode.lock_fhs);
 }
 EXPORT_SYMBOL_GPL(cec_queue_pin_cec_event);
 
@@ -195,10 +187,10 @@
 	};
 	struct cec_fh *fh;
 
-	mutex_lock(&adap->devnode.lock);
+	mutex_lock(&adap->devnode.lock_fhs);
 	list_for_each_entry(fh, &adap->devnode.fhs, list)
 		cec_queue_event_fh(fh, &ev, ktime_to_ns(ts));
-	mutex_unlock(&adap->devnode.lock);
+	mutex_unlock(&adap->devnode.lock_fhs);
 }
 EXPORT_SYMBOL_GPL(cec_queue_pin_hpd_event);
 
@@ -211,10 +203,10 @@
 	};
 	struct cec_fh *fh;
 
-	mutex_lock(&adap->devnode.lock);
+	mutex_lock(&adap->devnode.lock_fhs);
 	list_for_each_entry(fh, &adap->devnode.fhs, list)
 		cec_queue_event_fh(fh, &ev, ktime_to_ns(ts));
-	mutex_unlock(&adap->devnode.lock);
+	mutex_unlock(&adap->devnode.lock_fhs);
 }
 EXPORT_SYMBOL_GPL(cec_queue_pin_5v_event);
 
@@ -286,12 +278,12 @@
 	u32 monitor_mode = valid_la ? CEC_MODE_MONITOR :
 				      CEC_MODE_MONITOR_ALL;
 
-	mutex_lock(&adap->devnode.lock);
+	mutex_lock(&adap->devnode.lock_fhs);
 	list_for_each_entry(fh, &adap->devnode.fhs, list) {
 		if (fh->mode_follower >= monitor_mode)
 			cec_queue_msg_fh(fh, msg);
 	}
-	mutex_unlock(&adap->devnode.lock);
+	mutex_unlock(&adap->devnode.lock_fhs);
 }
 
 /*
@@ -302,12 +294,12 @@
 {
 	struct cec_fh *fh;
 
-	mutex_lock(&adap->devnode.lock);
+	mutex_lock(&adap->devnode.lock_fhs);
 	list_for_each_entry(fh, &adap->devnode.fhs, list) {
 		if (fh->mode_follower == CEC_MODE_FOLLOWER)
 			cec_queue_msg_fh(fh, msg);
 	}
-	mutex_unlock(&adap->devnode.lock);
+	mutex_unlock(&adap->devnode.lock_fhs);
 }
 
 /* Notify userspace of an adapter state change. */
@@ -365,38 +357,48 @@
 /*
  * A pending CEC transmit needs to be cancelled, either because the CEC
  * adapter is disabled or the transmit takes an impossibly long time to
- * finish.
+ * finish, or the reply timed out.
  *
  * This function is called with adap->lock held.
  */
-static void cec_data_cancel(struct cec_data *data, u8 tx_status)
+static void cec_data_cancel(struct cec_data *data, u8 tx_status, u8 rx_status)
 {
+	struct cec_adapter *adap = data->adap;
+
 	/*
 	 * It's either the current transmit, or it is a pending
 	 * transmit. Take the appropriate action to clear it.
 	 */
-	if (data->adap->transmitting == data) {
-		data->adap->transmitting = NULL;
+	if (adap->transmitting == data) {
+		adap->transmitting = NULL;
 	} else {
 		list_del_init(&data->list);
 		if (!(data->msg.tx_status & CEC_TX_STATUS_OK))
-			if (!WARN_ON(!data->adap->transmit_queue_sz))
-				data->adap->transmit_queue_sz--;
+			if (!WARN_ON(!adap->transmit_queue_sz))
+				adap->transmit_queue_sz--;
 	}
 
 	if (data->msg.tx_status & CEC_TX_STATUS_OK) {
 		data->msg.rx_ts = ktime_get_ns();
-		data->msg.rx_status = CEC_RX_STATUS_ABORTED;
+		data->msg.rx_status = rx_status;
+		if (!data->blocking)
+			data->msg.tx_status = 0;
 	} else {
 		data->msg.tx_ts = ktime_get_ns();
 		data->msg.tx_status |= tx_status |
 				       CEC_TX_STATUS_MAX_RETRIES;
 		data->msg.tx_error_cnt++;
 		data->attempts = 0;
+		if (!data->blocking)
+			data->msg.rx_status = 0;
 	}
 
 	/* Queue transmitted message for monitoring purposes */
-	cec_queue_msg_monitor(data->adap, &data->msg, 1);
+	cec_queue_msg_monitor(adap, &data->msg, 1);
+
+	if (!data->blocking && data->msg.sequence)
+		/* Allow drivers to react to a canceled transmit */
+		call_void_op(adap, adap_nb_transmit_canceled, &data->msg);
 
 	cec_data_completed(data);
 }
@@ -417,15 +419,15 @@
 	while (!list_empty(&adap->transmit_queue)) {
 		data = list_first_entry(&adap->transmit_queue,
 					struct cec_data, list);
-		cec_data_cancel(data, CEC_TX_STATUS_ABORTED);
+		cec_data_cancel(data, CEC_TX_STATUS_ABORTED, 0);
 	}
 	if (adap->transmitting)
-		cec_data_cancel(adap->transmitting, CEC_TX_STATUS_ABORTED);
+		adap->transmit_in_progress_aborted = true;
 
 	/* Cancel the pending timeout work. */
 	list_for_each_entry_safe(data, n, &adap->wait_queue, list) {
 		if (cancel_delayed_work(&data->work))
-			cec_data_cancel(data, CEC_TX_STATUS_OK);
+			cec_data_cancel(data, CEC_TX_STATUS_OK, CEC_RX_STATUS_ABORTED);
 		/*
 		 * If cancel_delayed_work returned false, then
 		 * the cec_wait_timeout function is running,
@@ -500,6 +502,15 @@
 			goto unlock;
 		}
 
+		if (adap->transmit_in_progress &&
+		    adap->transmit_in_progress_aborted) {
+			if (adap->transmitting)
+				cec_data_cancel(adap->transmitting,
+						CEC_TX_STATUS_ABORTED, 0);
+			adap->transmit_in_progress = false;
+			adap->transmit_in_progress_aborted = false;
+			goto unlock;
+		}
 		if (adap->transmit_in_progress && timeout) {
 			/*
 			 * If we timeout, then log that. Normally this does
@@ -515,7 +526,7 @@
 					adap->transmitting->msg.msg);
 				/* Just give up on this. */
 				cec_data_cancel(adap->transmitting,
-						CEC_TX_STATUS_TIMEOUT);
+						CEC_TX_STATUS_TIMEOUT, 0);
 			} else {
 				pr_warn("cec-%s: transmit timed out\n", adap->name);
 			}
@@ -571,10 +582,11 @@
 		if (data->attempts == 0)
 			data->attempts = attempts;
 
+		adap->transmit_in_progress_aborted = false;
 		/* Tell the adapter to transmit, cancel on error */
-		if (adap->ops->adap_transmit(adap, data->attempts,
-					     signal_free_time, &data->msg))
-			cec_data_cancel(data, CEC_TX_STATUS_ABORTED);
+		if (call_op(adap, adap_transmit, data->attempts,
+			    signal_free_time, &data->msg))
+			cec_data_cancel(data, CEC_TX_STATUS_ABORTED, 0);
 		else
 			adap->transmit_in_progress = true;
 
@@ -598,6 +610,8 @@
 	struct cec_msg *msg;
 	unsigned int attempts_made = arb_lost_cnt + nack_cnt +
 				     low_drive_cnt + error_cnt;
+	bool done = status & (CEC_TX_STATUS_MAX_RETRIES | CEC_TX_STATUS_OK);
+	bool aborted = adap->transmit_in_progress_aborted;
 
 	dprintk(2, "%s: status 0x%02x\n", __func__, status);
 	if (attempts_made < 1)
@@ -618,6 +632,7 @@
 		goto wake_thread;
 	}
 	adap->transmit_in_progress = false;
+	adap->transmit_in_progress_aborted = false;
 
 	msg = &data->msg;
 
@@ -638,8 +653,7 @@
 	 * the hardware didn't signal that it retried itself (by setting
 	 * CEC_TX_STATUS_MAX_RETRIES), then we will retry ourselves.
 	 */
-	if (data->attempts > attempts_made &&
-	    !(status & (CEC_TX_STATUS_MAX_RETRIES | CEC_TX_STATUS_OK))) {
+	if (!aborted && data->attempts > attempts_made && !done) {
 		/* Retry this message */
 		data->attempts -= attempts_made;
 		if (msg->timeout)
@@ -654,6 +668,8 @@
 		goto wake_thread;
 	}
 
+	if (aborted && !done)
+		status |= CEC_TX_STATUS_ABORTED;
 	data->attempts = 0;
 
 	/* Always set CEC_TX_STATUS_MAX_RETRIES on error */
@@ -732,9 +748,7 @@
 
 	/* Mark the message as timed out */
 	list_del_init(&data->list);
-	data->msg.rx_ts = ktime_get_ns();
-	data->msg.rx_status = CEC_RX_STATUS_TIMEOUT;
-	cec_data_completed(data);
+	cec_data_cancel(data, CEC_TX_STATUS_OK, CEC_RX_STATUS_TIMEOUT);
 unlock:
 	mutex_unlock(&adap->lock);
 }
@@ -750,6 +764,7 @@
 {
 	struct cec_data *data;
 	bool is_raw = msg_is_raw(msg);
+	int err;
 
 	if (adap->devnode.unregistered)
 		return -ENODEV;
@@ -912,14 +927,20 @@
 	 * Release the lock and wait, retake the lock afterwards.
 	 */
 	mutex_unlock(&adap->lock);
-	wait_for_completion_killable(&data->c);
-	if (!data->completed)
-		cancel_delayed_work_sync(&data->work);
+	err = wait_for_completion_killable(&data->c);
+	cancel_delayed_work_sync(&data->work);
 	mutex_lock(&adap->lock);
 
+	if (err)
+		adap->transmit_in_progress_aborted = true;
+
 	/* Cancel the transmit if it was interrupted */
-	if (!data->completed)
-		cec_data_cancel(data, CEC_TX_STATUS_ABORTED);
+	if (!data->completed) {
+		if (data->msg.tx_status & CEC_TX_STATUS_OK)
+			cec_data_cancel(data, CEC_TX_STATUS_OK, CEC_RX_STATUS_ABORTED);
+		else
+			cec_data_cancel(data, CEC_TX_STATUS_ABORTED, 0);
+	}
 
 	/* The transmit completed (possibly with an error) */
 	*msg = data->msg;
@@ -1085,7 +1106,8 @@
 	mutex_lock(&adap->lock);
 	dprintk(2, "%s: %*ph\n", __func__, msg->len, msg->msg);
 
-	adap->last_initiator = 0xff;
+	if (!adap->transmit_in_progress)
+		adap->last_initiator = 0xff;
 
 	/* Check if this message was for us (directed or broadcast). */
 	if (!cec_msg_is_broadcast(msg))
@@ -1115,20 +1137,6 @@
 	if (valid_la && min_len) {
 		/* These messages have special length requirements */
 		switch (cmd) {
-		case CEC_MSG_TIMER_STATUS:
-			if (msg->msg[2] & 0x10) {
-				switch (msg->msg[2] & 0xf) {
-				case CEC_OP_PROG_INFO_NOT_ENOUGH_SPACE:
-				case CEC_OP_PROG_INFO_MIGHT_NOT_BE_ENOUGH_SPACE:
-					if (msg->len < 5)
-						valid_la = false;
-					break;
-				}
-			} else if ((msg->msg[2] & 0xf) == CEC_OP_PROG_ERROR_DUPLICATE) {
-				if (msg->len < 5)
-					valid_la = false;
-			}
-			break;
 		case CEC_MSG_RECORD_ON:
 			switch (msg->msg[2]) {
 			case CEC_OP_RECORD_SRC_OWN:
@@ -1199,6 +1207,7 @@
 			if (abort)
 				dst->rx_status |= CEC_RX_STATUS_FEATURE_ABORT;
 			msg->flags = dst->flags;
+			msg->sequence = dst->sequence;
 			/* Remove it from the wait_queue */
 			list_del_init(&data->list);
 
@@ -1270,7 +1279,7 @@
 		 * While trying to poll the physical address was reset
 		 * and the adapter was unconfigured, so bail out.
 		 */
-		if (!adap->is_configuring)
+		if (adap->phys_addr == CEC_PHYS_ADDR_INVALID)
 			return -EINTR;
 
 		if (err)
@@ -1306,7 +1315,7 @@
 	 * Message not acknowledged, so this logical
 	 * address is free to use.
 	 */
-	err = adap->ops->adap_log_addr(adap, log_addr);
+	err = call_op(adap, adap_log_addr, log_addr);
 	if (err)
 		return err;
 
@@ -1323,11 +1332,9 @@
  */
 static void cec_adap_unconfigure(struct cec_adapter *adap)
 {
-	if (!adap->needs_hpd ||
-	    adap->phys_addr != CEC_PHYS_ADDR_INVALID)
-		WARN_ON(adap->ops->adap_log_addr(adap, CEC_LOG_ADDR_INVALID));
+	if (!adap->needs_hpd || adap->phys_addr != CEC_PHYS_ADDR_INVALID)
+		WARN_ON(call_op(adap, adap_log_addr, CEC_LOG_ADDR_INVALID));
 	adap->log_addrs.log_addr_mask = 0;
-	adap->is_configuring = false;
 	adap->is_configured = false;
 	cec_flush(adap);
 	wake_up_interruptible(&adap->kthread_waitq);
@@ -1519,9 +1526,10 @@
 	for (i = 0; i < las->num_log_addrs; i++)
 		las->log_addr[i] = CEC_LOG_ADDR_INVALID;
 	cec_adap_unconfigure(adap);
+	adap->is_configuring = false;
 	adap->kthread_config = NULL;
-	mutex_unlock(&adap->lock);
 	complete(&adap->config_completion);
+	mutex_unlock(&adap->lock);
 	return 0;
 }
 
@@ -1533,9 +1541,12 @@
  */
 static void cec_claim_log_addrs(struct cec_adapter *adap, bool block)
 {
-	if (WARN_ON(adap->is_configuring || adap->is_configured))
+	if (WARN_ON(adap->is_claiming_log_addrs ||
+		    adap->is_configuring || adap->is_configured))
 		return;
 
+	adap->is_claiming_log_addrs = true;
+
 	init_completion(&adap->config_completion);
 
 	/* Ready to kick off the thread */
@@ -1544,11 +1555,67 @@
 					   "ceccfg-%s", adap->name);
 	if (IS_ERR(adap->kthread_config)) {
 		adap->kthread_config = NULL;
+		adap->is_configuring = false;
 	} else if (block) {
 		mutex_unlock(&adap->lock);
 		wait_for_completion(&adap->config_completion);
 		mutex_lock(&adap->lock);
 	}
+	adap->is_claiming_log_addrs = false;
+}
+
+/*
+ * Helper function to enable/disable the CEC adapter.
+ *
+ * This function is called with adap->lock held.
+ */
+static int cec_adap_enable(struct cec_adapter *adap)
+{
+	bool enable;
+	int ret = 0;
+
+	enable = adap->monitor_all_cnt || adap->monitor_pin_cnt ||
+		 adap->log_addrs.num_log_addrs;
+	if (adap->needs_hpd)
+		enable = enable && adap->phys_addr != CEC_PHYS_ADDR_INVALID;
+
+	if (enable == adap->is_enabled)
+		return 0;
+
+	/* serialize adap_enable */
+	mutex_lock(&adap->devnode.lock);
+	if (enable) {
+		adap->last_initiator = 0xff;
+		adap->transmit_in_progress = false;
+		ret = adap->ops->adap_enable(adap, true);
+		if (!ret) {
+			/*
+			 * Enable monitor-all/pin modes if needed. We warn, but
+			 * continue if this fails as this is not a critical error.
+			 */
+			if (adap->monitor_all_cnt)
+				WARN_ON(call_op(adap, adap_monitor_all_enable, true));
+			if (adap->monitor_pin_cnt)
+				WARN_ON(call_op(adap, adap_monitor_pin_enable, true));
+		}
+	} else {
+		/* Disable monitor-all/pin modes if needed (needs_hpd == 1) */
+		if (adap->monitor_all_cnt)
+			WARN_ON(call_op(adap, adap_monitor_all_enable, false));
+		if (adap->monitor_pin_cnt)
+			WARN_ON(call_op(adap, adap_monitor_pin_enable, false));
+		WARN_ON(adap->ops->adap_enable(adap, false));
+		adap->last_initiator = 0xff;
+		adap->transmit_in_progress = false;
+		adap->transmit_in_progress_aborted = false;
+		if (adap->transmitting)
+			cec_data_cancel(adap->transmitting, CEC_TX_STATUS_ABORTED, 0);
+	}
+	if (!ret)
+		adap->is_enabled = enable;
+	wake_up_interruptible(&adap->kthread_waitq);
+	mutex_unlock(&adap->devnode.lock);
+	return ret;
 }
 
 /* Set a new physical address and send an event notifying userspace of this.
@@ -1557,52 +1624,30 @@
  */
 void __cec_s_phys_addr(struct cec_adapter *adap, u16 phys_addr, bool block)
 {
+	bool becomes_invalid = phys_addr == CEC_PHYS_ADDR_INVALID;
+	bool is_invalid = adap->phys_addr == CEC_PHYS_ADDR_INVALID;
+
 	if (phys_addr == adap->phys_addr)
 		return;
-	if (phys_addr != CEC_PHYS_ADDR_INVALID && adap->devnode.unregistered)
+	if (!becomes_invalid && adap->devnode.unregistered)
 		return;
 
 	dprintk(1, "new physical address %x.%x.%x.%x\n",
 		cec_phys_addr_exp(phys_addr));
-	if (phys_addr == CEC_PHYS_ADDR_INVALID ||
-	    adap->phys_addr != CEC_PHYS_ADDR_INVALID) {
+	if (becomes_invalid || !is_invalid) {
 		adap->phys_addr = CEC_PHYS_ADDR_INVALID;
 		cec_post_state_event(adap);
 		cec_adap_unconfigure(adap);
-		/* Disabling monitor all mode should always succeed */
-		if (adap->monitor_all_cnt)
-			WARN_ON(call_op(adap, adap_monitor_all_enable, false));
-		mutex_lock(&adap->devnode.lock);
-		if (adap->needs_hpd || list_empty(&adap->devnode.fhs)) {
-			WARN_ON(adap->ops->adap_enable(adap, false));
-			adap->transmit_in_progress = false;
-			wake_up_interruptible(&adap->kthread_waitq);
-		}
-		mutex_unlock(&adap->devnode.lock);
-		if (phys_addr == CEC_PHYS_ADDR_INVALID)
+		if (becomes_invalid) {
+			cec_adap_enable(adap);
 			return;
+		}
 	}
 
-	mutex_lock(&adap->devnode.lock);
-	adap->last_initiator = 0xff;
-	adap->transmit_in_progress = false;
-
-	if ((adap->needs_hpd || list_empty(&adap->devnode.fhs)) &&
-	    adap->ops->adap_enable(adap, true)) {
-		mutex_unlock(&adap->devnode.lock);
-		return;
-	}
-
-	if (adap->monitor_all_cnt &&
-	    call_op(adap, adap_monitor_all_enable, true)) {
-		if (adap->needs_hpd || list_empty(&adap->devnode.fhs))
-			WARN_ON(adap->ops->adap_enable(adap, false));
-		mutex_unlock(&adap->devnode.lock);
-		return;
-	}
-	mutex_unlock(&adap->devnode.lock);
-
 	adap->phys_addr = phys_addr;
+	if (is_invalid)
+		cec_adap_enable(adap);
+
 	cec_post_state_event(adap);
 	if (adap->log_addrs.num_log_addrs)
 		cec_claim_log_addrs(adap, block);
@@ -1659,12 +1704,15 @@
 		      struct cec_log_addrs *log_addrs, bool block)
 {
 	u16 type_mask = 0;
+	int err;
 	int i;
 
 	if (adap->devnode.unregistered)
 		return -ENODEV;
 
 	if (!log_addrs || log_addrs->num_log_addrs == 0) {
+		if (!adap->is_configuring && !adap->is_configured)
+			return 0;
 		cec_adap_unconfigure(adap);
 		adap->log_addrs.num_log_addrs = 0;
 		for (i = 0; i < CEC_MAX_LOG_ADDRS; i++)
@@ -1672,6 +1720,7 @@
 		adap->log_addrs.osd_name[0] = '\0';
 		adap->log_addrs.vendor_id = CEC_VENDOR_ID_NONE;
 		adap->log_addrs.cec_version = CEC_OP_CEC_VERSION_2_0;
+		cec_adap_enable(adap);
 		return 0;
 	}
 
@@ -1807,9 +1856,10 @@
 
 	log_addrs->log_addr_mask = adap->log_addrs.log_addr_mask;
 	adap->log_addrs = *log_addrs;
-	if (adap->phys_addr != CEC_PHYS_ADDR_INVALID)
+	err = cec_adap_enable(adap);
+	if (!err && adap->phys_addr != CEC_PHYS_ADDR_INVALID)
 		cec_claim_log_addrs(adap, block);
-	return 0;
+	return err;
 }
 
 int cec_s_log_addrs(struct cec_adapter *adap,
@@ -1911,11 +1961,10 @@
 	    msg->msg[1] != CEC_MSG_CDC_MESSAGE)
 		return 0;
 
-	if (adap->ops->received) {
-		/* Allow drivers to process the message first */
-		if (adap->ops->received(adap, msg) != -ENOMSG)
-			return 0;
-	}
+	/* Allow drivers to process the message first */
+	if (adap->ops->received && !adap->devnode.unregistered &&
+	    adap->ops->received(adap, msg) != -ENOMSG)
+		return 0;
 
 	/*
 	 * REPORT_PHYSICAL_ADDR, CEC_MSG_USER_CONTROL_PRESSED and
@@ -2108,20 +2157,25 @@
  */
 int cec_monitor_all_cnt_inc(struct cec_adapter *adap)
 {
-	int ret = 0;
+	int ret;
+
+	if (adap->monitor_all_cnt++)
+		return 0;
 
-	if (adap->monitor_all_cnt == 0)
-		ret = call_op(adap, adap_monitor_all_enable, 1);
-	if (ret == 0)
-		adap->monitor_all_cnt++;
+	ret = cec_adap_enable(adap);
+	if (ret)
+		adap->monitor_all_cnt--;
 	return ret;
 }
 
 void cec_monitor_all_cnt_dec(struct cec_adapter *adap)
 {
-	adap->monitor_all_cnt--;
-	if (adap->monitor_all_cnt == 0)
-		WARN_ON(call_op(adap, adap_monitor_all_enable, 0));
+	if (WARN_ON(!adap->monitor_all_cnt))
+		return;
+	if (--adap->monitor_all_cnt)
+		return;
+	WARN_ON(call_op(adap, adap_monitor_all_enable, false));
+	cec_adap_enable(adap);
 }
 
 /*
@@ -2131,20 +2185,25 @@
  */
 int cec_monitor_pin_cnt_inc(struct cec_adapter *adap)
 {
-	int ret = 0;
+	int ret;
+
+	if (adap->monitor_pin_cnt++)
+		return 0;
 
-	if (adap->monitor_pin_cnt == 0)
-		ret = call_op(adap, adap_monitor_pin_enable, 1);
-	if (ret == 0)
-		adap->monitor_pin_cnt++;
+	ret = cec_adap_enable(adap);
+	if (ret)
+		adap->monitor_pin_cnt--;
 	return ret;
 }
 
 void cec_monitor_pin_cnt_dec(struct cec_adapter *adap)
 {
-	adap->monitor_pin_cnt--;
-	if (adap->monitor_pin_cnt == 0)
-		WARN_ON(call_op(adap, adap_monitor_pin_enable, 0));
+	if (WARN_ON(!adap->monitor_pin_cnt))
+		return;
+	if (--adap->monitor_pin_cnt)
+		return;
+	WARN_ON(call_op(adap, adap_monitor_pin_enable, false));
+	cec_adap_enable(adap);
 }
 
 #ifdef CONFIG_DEBUG_FS
@@ -2158,6 +2217,7 @@
 	struct cec_data *data;
 
 	mutex_lock(&adap->lock);
+	seq_printf(file, "enabled: %d\n", adap->is_enabled);
 	seq_printf(file, "configured: %d\n", adap->is_configured);
 	seq_printf(file, "configuring: %d\n", adap->is_configuring);
 	seq_printf(file, "phys_addr: %x.%x.%x.%x\n",
@@ -2172,6 +2232,9 @@
 	if (adap->monitor_all_cnt)
 		seq_printf(file, "file handles in Monitor All mode: %u\n",
 			   adap->monitor_all_cnt);
+	if (adap->monitor_pin_cnt)
+		seq_printf(file, "file handles in Monitor Pin mode: %u\n",
+			   adap->monitor_pin_cnt);
 	if (adap->tx_timeouts) {
 		seq_printf(file, "transmit timeouts: %u\n",
 			   adap->tx_timeouts);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/core/cec-api.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/core/cec-api.c
@@ -178,7 +178,7 @@
 			   CEC_LOG_ADDRS_FL_ALLOW_RC_PASSTHRU |
 			   CEC_LOG_ADDRS_FL_CDC_ONLY;
 	mutex_lock(&adap->lock);
-	if (!adap->is_configuring &&
+	if (!adap->is_claiming_log_addrs && !adap->is_configuring &&
 	    (!log_addrs.num_log_addrs || !adap->is_configured) &&
 	    !cec_is_busy(adap, fh)) {
 		err = __cec_s_log_addrs(adap, &log_addrs, block);
@@ -586,17 +586,6 @@
 		return err;
 	}
 
-	mutex_lock(&devnode->lock);
-	if (list_empty(&devnode->fhs) &&
-	    !adap->needs_hpd &&
-	    adap->phys_addr == CEC_PHYS_ADDR_INVALID) {
-		err = adap->ops->adap_enable(adap, true);
-		if (err) {
-			mutex_unlock(&devnode->lock);
-			kfree(fh);
-			return err;
-		}
-	}
 	filp->private_data = fh;
 
 	/* Queue up initial state events */
@@ -606,7 +595,8 @@
 		adap->conn_info.type != CEC_CONNECTOR_TYPE_NO_CONNECTOR;
 	cec_queue_event_fh(fh, &ev, 0);
 #ifdef CONFIG_CEC_PIN
-	if (adap->pin && adap->pin->ops->read_hpd) {
+	if (adap->pin && adap->pin->ops->read_hpd &&
+	    !adap->devnode.unregistered) {
 		err = adap->pin->ops->read_hpd(adap);
 		if (err >= 0) {
 			ev.event = err ? CEC_EVENT_PIN_HPD_HIGH :
@@ -614,7 +604,8 @@
 			cec_queue_event_fh(fh, &ev, 0);
 		}
 	}
-	if (adap->pin && adap->pin->ops->read_5v) {
+	if (adap->pin && adap->pin->ops->read_5v &&
+	    !adap->devnode.unregistered) {
 		err = adap->pin->ops->read_5v(adap);
 		if (err >= 0) {
 			ev.event = err ? CEC_EVENT_PIN_5V_HIGH :
@@ -624,7 +615,10 @@
 	}
 #endif
 
+	mutex_lock(&devnode->lock);
+	mutex_lock(&devnode->lock_fhs);
 	list_add(&fh->list, &devnode->fhs);
+	mutex_unlock(&devnode->lock_fhs);
 	mutex_unlock(&devnode->lock);
 
 	return 0;
@@ -654,11 +648,9 @@
 	mutex_unlock(&adap->lock);
 
 	mutex_lock(&devnode->lock);
+	mutex_lock(&devnode->lock_fhs);
 	list_del(&fh->list);
-	if (cec_is_registered(adap) && list_empty(&devnode->fhs) &&
-	    !adap->needs_hpd && adap->phys_addr == CEC_PHYS_ADDR_INVALID) {
-		WARN_ON(adap->ops->adap_enable(adap, false));
-	}
+	mutex_unlock(&devnode->lock_fhs);
 	mutex_unlock(&devnode->lock);
 
 	/* Unhook pending transmits from this filehandle. */
@@ -672,6 +664,8 @@
 		list_del(&data->xfer_list);
 	}
 	mutex_unlock(&adap->lock);
+
+	mutex_lock(&fh->lock);
 	while (!list_empty(&fh->msgs)) {
 		struct cec_msg_entry *entry =
 			list_first_entry(&fh->msgs, struct cec_msg_entry, list);
@@ -689,6 +683,7 @@
 			kfree(entry);
 		}
 	}
+	mutex_unlock(&fh->lock);
 	kfree(fh);
 
 	cec_put_device(devnode);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/core/cec-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/core/cec-core.c
@@ -169,8 +169,10 @@
 	devnode->registered = false;
 	devnode->unregistered = true;
 
+	mutex_lock(&devnode->lock_fhs);
 	list_for_each_entry(fh, &devnode->fhs, list)
 		wake_up_interruptible(&fh->wait);
+	mutex_unlock(&devnode->lock_fhs);
 
 	mutex_unlock(&devnode->lock);
 
@@ -202,7 +204,7 @@
 		line = strsep(&p, "\n");
 		if (!*line || *line == '#')
 			continue;
-		if (!adap->ops->error_inj_parse_line(adap, line)) {
+		if (!call_op(adap, error_inj_parse_line, line)) {
 			kfree(buf);
 			return -EINVAL;
 		}
@@ -215,7 +217,7 @@
 {
 	struct cec_adapter *adap = sf->private;
 
-	return adap->ops->error_inj_show(adap, sf);
+	return call_op(adap, error_inj_show, sf);
 }
 
 static int cec_error_inj_open(struct inode *inode, struct file *file)
@@ -272,6 +274,7 @@
 
 	/* adap->devnode initialization */
 	INIT_LIST_HEAD(&adap->devnode.fhs);
+	mutex_init(&adap->devnode.lock_fhs);
 	mutex_init(&adap->devnode.lock);
 
 	adap->kthread = kthread_run(cec_thread_func, adap, "cec-%s", name);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/core/cec-pin-priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/core/cec-pin-priv.h
@@ -12,6 +12,17 @@
 #include <linux/atomic.h>
 #include <media/cec-pin.h>
 
+#define call_pin_op(pin, op, arg...)					\
+	((pin && pin->ops->op && !pin->adap->devnode.unregistered) ?	\
+	 pin->ops->op(pin->adap, ## arg) : 0)
+
+#define call_void_pin_op(pin, op, arg...)				\
+	do {								\
+		if (pin && pin->ops->op &&				\
+		    !pin->adap->devnode.unregistered)			\
+			pin->ops->op(pin->adap, ## arg);		\
+	} while (0)
+
 enum cec_pin_state {
 	/* CEC is off */
 	CEC_ST_OFF,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/core/cec-pin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/core/cec-pin.c
@@ -135,7 +135,7 @@
 
 static bool cec_pin_read(struct cec_pin *pin)
 {
-	bool v = pin->ops->read(pin->adap);
+	bool v = call_pin_op(pin, read);
 
 	cec_pin_update(pin, v, false);
 	return v;
@@ -143,13 +143,13 @@
 
 static void cec_pin_low(struct cec_pin *pin)
 {
-	pin->ops->low(pin->adap);
+	call_void_pin_op(pin, low);
 	cec_pin_update(pin, false, false);
 }
 
 static bool cec_pin_high(struct cec_pin *pin)
 {
-	pin->ops->high(pin->adap);
+	call_void_pin_op(pin, high);
 	return cec_pin_read(pin);
 }
 
@@ -1033,6 +1033,7 @@
 {
 	struct cec_adapter *adap = _adap;
 	struct cec_pin *pin = adap->pin;
+	bool irq_enabled = false;
 
 	for (;;) {
 		wait_event_interruptible(pin->kthread_waitq,
@@ -1060,6 +1061,7 @@
 				ns_to_ktime(pin->work_rx_msg.rx_ts));
 			msg->len = 0;
 		}
+
 		if (pin->work_tx_status) {
 			unsigned int tx_status = pin->work_tx_status;
 
@@ -1083,27 +1085,39 @@
 		switch (atomic_xchg(&pin->work_irq_change,
 				    CEC_PIN_IRQ_UNCHANGED)) {
 		case CEC_PIN_IRQ_DISABLE:
-			pin->ops->disable_irq(adap);
+			if (irq_enabled) {
+				call_void_pin_op(pin, disable_irq);
+				irq_enabled = false;
+			}
 			cec_pin_high(pin);
 			cec_pin_to_idle(pin);
 			hrtimer_start(&pin->timer, ns_to_ktime(0),
 				      HRTIMER_MODE_REL);
 			break;
 		case CEC_PIN_IRQ_ENABLE:
-			pin->enable_irq_failed = !pin->ops->enable_irq(adap);
+			if (irq_enabled)
+				break;
+			pin->enable_irq_failed = !call_pin_op(pin, enable_irq);
 			if (pin->enable_irq_failed) {
 				cec_pin_to_idle(pin);
 				hrtimer_start(&pin->timer, ns_to_ktime(0),
 					      HRTIMER_MODE_REL);
+			} else {
+				irq_enabled = true;
 			}
 			break;
 		default:
 			break;
 		}
-
 		if (kthread_should_stop())
 			break;
 	}
+	if (irq_enabled)
+		call_void_pin_op(pin, disable_irq);
+	hrtimer_cancel(&pin->timer);
+	cec_pin_read(pin);
+	cec_pin_to_idle(pin);
+	pin->state = CEC_ST_OFF;
 	return 0;
 }
 
@@ -1130,13 +1144,7 @@
 		hrtimer_start(&pin->timer, ns_to_ktime(0),
 			      HRTIMER_MODE_REL);
 	} else {
-		if (pin->ops->disable_irq)
-			pin->ops->disable_irq(adap);
-		hrtimer_cancel(&pin->timer);
 		kthread_stop(pin->kthread);
-		cec_pin_read(pin);
-		cec_pin_to_idle(pin);
-		pin->state = CEC_ST_OFF;
 	}
 	return 0;
 }
@@ -1157,11 +1165,8 @@
 	if (pin->state != CEC_ST_RX_IRQ)
 		return;
 
-	atomic_set(&pin->work_irq_change, CEC_PIN_IRQ_UNCHANGED);
-	pin->ops->disable_irq(pin->adap);
-	cec_pin_high(pin);
-	cec_pin_to_idle(pin);
-	hrtimer_start(&pin->timer, ns_to_ktime(0), HRTIMER_MODE_REL);
+	atomic_set(&pin->work_irq_change, CEC_PIN_IRQ_DISABLE);
+	wake_up_interruptible(&pin->kthread_waitq);
 }
 
 static int cec_pin_adap_transmit(struct cec_adapter *adap, u8 attempts,
@@ -1203,7 +1208,7 @@
 	seq_printf(file, "state: %s\n", states[pin->state].name);
 	seq_printf(file, "tx_bit: %d\n", pin->tx_bit);
 	seq_printf(file, "rx_bit: %d\n", pin->rx_bit);
-	seq_printf(file, "cec pin: %d\n", pin->ops->read(adap));
+	seq_printf(file, "cec pin: %d\n", call_pin_op(pin, read));
 	seq_printf(file, "cec pin events dropped: %u\n",
 		   pin->work_pin_events_dropped_cnt);
 	seq_printf(file, "irq failed: %d\n", pin->enable_irq_failed);
@@ -1256,8 +1261,7 @@
 	pin->rx_data_bit_too_long_cnt = 0;
 	pin->rx_low_drive_cnt = 0;
 	pin->tx_low_drive_cnt = 0;
-	if (pin->ops->status)
-		pin->ops->status(adap, file);
+	call_void_pin_op(pin, status, file);
 }
 
 static int cec_pin_adap_monitor_all_enable(struct cec_adapter *adap,
@@ -1273,7 +1277,7 @@
 {
 	struct cec_pin *pin = adap->pin;
 
-	if (pin->ops->free)
+	if (pin && pin->ops->free)
 		pin->ops->free(adap);
 	adap->pin = NULL;
 	kfree(pin);
@@ -1283,7 +1287,7 @@
 {
 	struct cec_pin *pin = adap->pin;
 
-	if (pin->ops->received)
+	if (pin->ops->received && !adap->devnode.unregistered)
 		return pin->ops->received(adap, msg);
 	return -ENOMSG;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/core/cec-priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/core/cec-priv.h
@@ -17,6 +17,16 @@
 			pr_info("cec-%s: " fmt, adap->name, ## arg);	\
 	} while (0)
 
+#define call_op(adap, op, arg...)					\
+	((adap->ops->op && !adap->devnode.unregistered) ?		\
+	 adap->ops->op(adap, ## arg) : 0)
+
+#define call_void_op(adap, op, arg...)					\
+	do {								\
+		if (adap->ops->op && !adap->devnode.unregistered)	\
+			adap->ops->op(adap, ## arg);			\
+	} while (0)
+
 /* devnode to cec_adapter */
 #define to_cec_adapter(node) container_of(node, struct cec_adapter, devnode)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/i2c/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/i2c/Kconfig
@@ -5,6 +5,7 @@
 config CEC_CH7322
 	tristate "Chrontel CH7322 CEC controller"
 	depends on I2C
+	select REGMAP
 	select REGMAP_I2C
 	select CEC_CORE
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/platform/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/platform/Makefile
@@ -6,7 +6,7 @@
 # Please keep it in alphabetic order
 obj-$(CONFIG_CEC_CROS_EC)	+= cros-ec/
 obj-$(CONFIG_CEC_GPIO)		+= cec-gpio/
-obj-$(CONFIG_CEC_MESON_AO)	+= meson/
+obj-y				+= meson/
 obj-$(CONFIG_CEC_SAMSUNG_S5P)	+= s5p/
 obj-$(CONFIG_CEC_SECO)		+= seco/
 obj-$(CONFIG_CEC_STI)		+= sti/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/platform/cros-ec/cros-ec-cec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/platform/cros-ec/cros-ec-cec.c
@@ -44,6 +44,8 @@
 	uint8_t *cec_message = cros_ec->event_data.data.cec_message;
 	unsigned int len = cros_ec->event_size;
 
+	if (len > CEC_MAX_MSG_SIZE)
+		len = CEC_MAX_MSG_SIZE;
 	cros_ec_cec->rx_msg.len = len;
 	memcpy(cros_ec_cec->rx_msg.msg, cec_message, len);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/platform/s5p/s5p_cec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/platform/s5p/s5p_cec.c
@@ -115,6 +115,8 @@
 				dev_dbg(cec->dev, "Buffer overrun (worker did not process previous message)\n");
 			cec->rx = STATE_BUSY;
 			cec->msg.len = status >> 24;
+			if (cec->msg.len > CEC_MAX_MSG_SIZE)
+				cec->msg.len = CEC_MAX_MSG_SIZE;
 			cec->msg.rx_status = CEC_RX_STATUS_OK;
 			s5p_cec_get_rx_buf(cec, cec->msg.len,
 					cec->msg.msg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/cec/usb/pulse8/pulse8-cec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/cec/usb/pulse8/pulse8-cec.c
@@ -685,7 +685,7 @@
 	err = pulse8_send_and_wait(pulse8, cmd, 1, cmd[0], 4);
 	if (err)
 		return err;
-	date = (data[0] << 24) | (data[1] << 16) | (data[2] << 8) | data[3];
+	date = ((unsigned)data[0] << 24) | (data[1] << 16) | (data[2] << 8) | data[3];
 	dev_info(pulse8->dev, "Firmware build date %ptT\n", &date);
 
 	dev_dbg(pulse8->dev, "Persistent config:\n");
@@ -809,8 +809,11 @@
 
 	mutex_lock(&pulse8->lock);
 	cmd = MSGCODE_PING;
-	pulse8_send_and_wait(pulse8, &cmd, 1,
-			     MSGCODE_COMMAND_ACCEPTED, 0);
+	if (pulse8_send_and_wait(pulse8, &cmd, 1,
+				 MSGCODE_COMMAND_ACCEPTED, 0)) {
+		dev_warn(pulse8->dev, "failed to ping EEPROM\n");
+		goto unlock;
+	}
 
 	if (pulse8->vers < 2)
 		goto unlock;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/saa7146/saa7146_fops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/saa7146/saa7146_fops.c
@@ -521,7 +521,7 @@
 		ERR("out of memory. aborting.\n");
 		kfree(vv);
 		v4l2_ctrl_handler_free(hdl);
-		return -1;
+		return -ENOMEM;
 	}
 
 	saa7146_video_uops.init(dev,vv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/v4l2-tpg/v4l2-tpg-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/v4l2-tpg/v4l2-tpg-core.c
@@ -113,6 +113,7 @@
 {
 	unsigned pat;
 	unsigned plane;
+	int ret = 0;
 
 	tpg->max_line_width = max_w;
 	for (pat = 0; pat < TPG_MAX_PAT_LINES; pat++) {
@@ -121,14 +122,18 @@
 
 			tpg->lines[pat][plane] =
 				vzalloc(array3_size(max_w, 2, pixelsz));
-			if (!tpg->lines[pat][plane])
-				return -ENOMEM;
+			if (!tpg->lines[pat][plane]) {
+				ret = -ENOMEM;
+				goto free_lines;
+			}
 			if (plane == 0)
 				continue;
 			tpg->downsampled_lines[pat][plane] =
 				vzalloc(array3_size(max_w, 2, pixelsz));
-			if (!tpg->downsampled_lines[pat][plane])
-				return -ENOMEM;
+			if (!tpg->downsampled_lines[pat][plane]) {
+				ret = -ENOMEM;
+				goto free_lines;
+			}
 		}
 	}
 	for (plane = 0; plane < TPG_MAX_PLANES; plane++) {
@@ -136,18 +141,45 @@
 
 		tpg->contrast_line[plane] =
 			vzalloc(array_size(pixelsz, max_w));
-		if (!tpg->contrast_line[plane])
-			return -ENOMEM;
+		if (!tpg->contrast_line[plane]) {
+			ret = -ENOMEM;
+			goto free_contrast_line;
+		}
 		tpg->black_line[plane] =
 			vzalloc(array_size(pixelsz, max_w));
-		if (!tpg->black_line[plane])
-			return -ENOMEM;
+		if (!tpg->black_line[plane]) {
+			ret = -ENOMEM;
+			goto free_contrast_line;
+		}
 		tpg->random_line[plane] =
 			vzalloc(array3_size(max_w, 2, pixelsz));
-		if (!tpg->random_line[plane])
-			return -ENOMEM;
+		if (!tpg->random_line[plane]) {
+			ret = -ENOMEM;
+			goto free_contrast_line;
+		}
 	}
 	return 0;
+
+free_contrast_line:
+	for (plane = 0; plane < TPG_MAX_PLANES; plane++) {
+		vfree(tpg->contrast_line[plane]);
+		vfree(tpg->black_line[plane]);
+		vfree(tpg->random_line[plane]);
+		tpg->contrast_line[plane] = NULL;
+		tpg->black_line[plane] = NULL;
+		tpg->random_line[plane] = NULL;
+	}
+free_lines:
+	for (pat = 0; pat < TPG_MAX_PAT_LINES; pat++)
+		for (plane = 0; plane < TPG_MAX_PLANES; plane++) {
+			vfree(tpg->lines[pat][plane]);
+			tpg->lines[pat][plane] = NULL;
+			if (plane == 0)
+				continue;
+			vfree(tpg->downsampled_lines[pat][plane]);
+			tpg->downsampled_lines[pat][plane] = NULL;
+		}
+	return ret;
 }
 EXPORT_SYMBOL_GPL(tpg_alloc);
 
@@ -285,6 +317,14 @@
 	case V4L2_PIX_FMT_YVU422M:
 		tpg->buffers = 3;
 		fallthrough;
+	case V4L2_PIX_FMT_YUV444P:
+		tpg->vdownsampling[1] = 1;
+		tpg->vdownsampling[2] = 1;
+		tpg->hdownsampling[1] = 1;
+		tpg->hdownsampling[2] = 1;
+		tpg->planes = 3;
+		tpg->color_enc = TGP_COLOR_ENC_YCBCR;
+		break;
 	case V4L2_PIX_FMT_YUV422P:
 		tpg->vdownsampling[1] = 1;
 		tpg->vdownsampling[2] = 1;
@@ -445,6 +485,7 @@
 		tpg->twopixelsize[0] = 4;
 		tpg->twopixelsize[1] = 4;
 		break;
+	case V4L2_PIX_FMT_YUV444P:
 	case V4L2_PIX_FMT_YUV444M:
 	case V4L2_PIX_FMT_YVU444M:
 	case V4L2_PIX_FMT_YUV422M:
@@ -1196,6 +1237,7 @@
 		buf[1][1] = g_u_s;
 		break;
 
+	case V4L2_PIX_FMT_YUV444P:
 	case V4L2_PIX_FMT_YUV444M:
 		buf[0][offset] = r_y_h;
 		buf[1][offset] = g_u_s;
@@ -1757,6 +1799,9 @@
 	unsigned p;
 	unsigned x;
 
+	if (WARN_ON_ONCE(!tpg->src_width || !tpg->scaled_width))
+		return;
+
 	switch (tpg->pattern) {
 	case TPG_PAT_GREEN:
 		contrast = TPG_COLOR_100_RED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/videobuf2/frame_vector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/videobuf2/frame_vector.c
@@ -30,15 +30,16 @@
  * different type underlying the specified range of virtual addresses.
  * When the function isn't able to map a single page, it returns error.
  *
+ * Note that get_vaddr_frames() cannot follow VM_IO mappings. It used
+ * to be able to do that, but that could (racily) return non-refcounted
+ * pfns.
+ *
  * This function takes care of grabbing mmap_lock as necessary.
  */
 int get_vaddr_frames(unsigned long start, unsigned int nr_frames,
 		     struct frame_vector *vec)
 {
-	struct mm_struct *mm = current->mm;
-	struct vm_area_struct *vma;
-	int ret = 0;
-	int err;
+	int ret;
 
 	if (nr_frames == 0)
 		return 0;
@@ -51,45 +52,15 @@
 	ret = pin_user_pages_fast(start, nr_frames,
 				  FOLL_FORCE | FOLL_WRITE | FOLL_LONGTERM,
 				  (struct page **)(vec->ptrs));
-	if (ret > 0) {
-		vec->got_ref = true;
-		vec->is_pfns = false;
-		goto out_unlocked;
-	}
-
-	mmap_read_lock(mm);
-	vec->got_ref = false;
-	vec->is_pfns = true;
-	ret = 0;
-	do {
-		unsigned long *nums = frame_vector_pfns(vec);
-
-		vma = vma_lookup(mm, start);
-		if (!vma)
-			break;
-
-		while (ret < nr_frames && start + PAGE_SIZE <= vma->vm_end) {
-			err = follow_pfn(vma, start, &nums[ret]);
-			if (err) {
-				if (ret == 0)
-					ret = err;
-				goto out;
-			}
-			start += PAGE_SIZE;
-			ret++;
-		}
-		/* Bail out if VMA doesn't completely cover the tail page. */
-		if (start < vma->vm_end)
-			break;
-	} while (ret < nr_frames);
-out:
-	mmap_read_unlock(mm);
-out_unlocked:
-	if (!ret)
-		ret = -EFAULT;
-	if (ret > 0)
-		vec->nr_frames = ret;
-	return ret;
+	vec->got_ref = true;
+	vec->is_pfns = false;
+	vec->nr_frames = ret;
+
+	if (likely(ret > 0))
+		return ret;
+
+	vec->nr_frames = 0;
+	return ret ? ret : -EFAULT;
 }
 EXPORT_SYMBOL(get_vaddr_frames);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/videobuf2/videobuf2-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/videobuf2/videobuf2-core.c
@@ -68,13 +68,13 @@
 	err;								\
 })
 
-#define call_ptr_memop(vb, op, args...)					\
+#define call_ptr_memop(op, vb, args...)					\
 ({									\
 	struct vb2_queue *_q = (vb)->vb2_queue;				\
 	void *ptr;							\
 									\
 	log_memop(vb, op);						\
-	ptr = _q->mem_ops->op ? _q->mem_ops->op(args) : NULL;		\
+	ptr = _q->mem_ops->op ? _q->mem_ops->op(vb, args) : NULL;	\
 	if (!IS_ERR_OR_NULL(ptr))					\
 		(vb)->cnt_mem_ ## op++;					\
 	ptr;								\
@@ -144,9 +144,9 @@
 	((vb)->vb2_queue->mem_ops->op ?					\
 		(vb)->vb2_queue->mem_ops->op(args) : 0)
 
-#define call_ptr_memop(vb, op, args...)					\
+#define call_ptr_memop(op, vb, args...)					\
 	((vb)->vb2_queue->mem_ops->op ?					\
-		(vb)->vb2_queue->mem_ops->op(args) : NULL)
+		(vb)->vb2_queue->mem_ops->op(vb, args) : NULL)
 
 #define call_void_memop(vb, op, args...)				\
 	do {								\
@@ -230,9 +230,10 @@
 		if (size < vb->planes[plane].length)
 			goto free;
 
-		mem_priv = call_ptr_memop(vb, alloc,
-				q->alloc_devs[plane] ? : q->dev,
-				q->dma_attrs, size, q->dma_dir, q->gfp_flags);
+		mem_priv = call_ptr_memop(alloc,
+					  vb,
+					  q->alloc_devs[plane] ? : q->dev,
+					  size);
 		if (IS_ERR_OR_NULL(mem_priv)) {
 			if (mem_priv)
 				ret = PTR_ERR(mem_priv);
@@ -301,6 +302,10 @@
 	p->mem_priv = NULL;
 	p->dbuf = NULL;
 	p->dbuf_mapped = 0;
+	p->bytesused = 0;
+	p->length = 0;
+	p->m.fd = 0;
+	p->data_offset = 0;
 }
 
 /*
@@ -787,7 +792,13 @@
 	num_buffers = max_t(unsigned int, *count, q->min_buffers_needed);
 	num_buffers = min_t(unsigned int, num_buffers, VB2_MAX_FRAME);
 	memset(q->alloc_devs, 0, sizeof(q->alloc_devs));
+	/*
+	 * Set this now to ensure that drivers see the correct q->memory value
+	 * in the queue_setup op.
+	 */
+	mutex_lock(&q->mmap_lock);
 	q->memory = memory;
+	mutex_unlock(&q->mmap_lock);
 
 	/*
 	 * Ask the driver how many buffers and planes per buffer it requires.
@@ -796,22 +807,27 @@
 	ret = call_qop(q, queue_setup, q, &num_buffers, &num_planes,
 		       plane_sizes, q->alloc_devs);
 	if (ret)
-		return ret;
+		goto error;
 
 	/* Check that driver has set sane values */
-	if (WARN_ON(!num_planes))
-		return -EINVAL;
+	if (WARN_ON(!num_planes)) {
+		ret = -EINVAL;
+		goto error;
+	}
 
 	for (i = 0; i < num_planes; i++)
-		if (WARN_ON(!plane_sizes[i]))
-			return -EINVAL;
+		if (WARN_ON(!plane_sizes[i])) {
+			ret = -EINVAL;
+			goto error;
+		}
 
 	/* Finally, allocate buffers and video memory */
 	allocated_buffers =
 		__vb2_queue_alloc(q, memory, num_buffers, num_planes, plane_sizes);
 	if (allocated_buffers == 0) {
 		dprintk(q, 1, "memory allocation failed\n");
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto error;
 	}
 
 	/*
@@ -852,7 +868,8 @@
 	if (ret < 0) {
 		/*
 		 * Note: __vb2_queue_free() will subtract 'allocated_buffers'
-		 * from q->num_buffers.
+		 * from q->num_buffers and it will reset q->memory to
+		 * VB2_MEMORY_UNKNOWN.
 		 */
 		__vb2_queue_free(q, allocated_buffers);
 		mutex_unlock(&q->mmap_lock);
@@ -868,6 +885,12 @@
 	q->waiting_for_buffers = !q->is_output;
 
 	return 0;
+
+error:
+	mutex_lock(&q->mmap_lock);
+	q->memory = VB2_MEMORY_UNKNOWN;
+	mutex_unlock(&q->mmap_lock);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(vb2_core_reqbufs);
 
@@ -878,6 +901,7 @@
 {
 	unsigned int num_planes = 0, num_buffers, allocated_buffers;
 	unsigned plane_sizes[VB2_MAX_PLANES] = { };
+	bool no_previous_buffers = !q->num_buffers;
 	int ret;
 
 	if (q->num_buffers == VB2_MAX_FRAME) {
@@ -885,13 +909,19 @@
 		return -ENOBUFS;
 	}
 
-	if (!q->num_buffers) {
+	if (no_previous_buffers) {
 		if (q->waiting_in_dqbuf && *count) {
 			dprintk(q, 1, "another dup()ped fd is waiting for a buffer\n");
 			return -EBUSY;
 		}
 		memset(q->alloc_devs, 0, sizeof(q->alloc_devs));
+		/*
+		 * Set this now to ensure that drivers see the correct q->memory
+		 * value in the queue_setup op.
+		 */
+		mutex_lock(&q->mmap_lock);
 		q->memory = memory;
+		mutex_unlock(&q->mmap_lock);
 		q->waiting_for_buffers = !q->is_output;
 	} else {
 		if (q->memory != memory) {
@@ -914,14 +944,15 @@
 	ret = call_qop(q, queue_setup, q, &num_buffers,
 		       &num_planes, plane_sizes, q->alloc_devs);
 	if (ret)
-		return ret;
+		goto error;
 
 	/* Finally, allocate buffers and video memory */
 	allocated_buffers = __vb2_queue_alloc(q, memory, num_buffers,
 				num_planes, plane_sizes);
 	if (allocated_buffers == 0) {
 		dprintk(q, 1, "memory allocation failed\n");
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto error;
 	}
 
 	/*
@@ -952,7 +983,8 @@
 	if (ret < 0) {
 		/*
 		 * Note: __vb2_queue_free() will subtract 'allocated_buffers'
-		 * from q->num_buffers.
+		 * from q->num_buffers and it will reset q->memory to
+		 * VB2_MEMORY_UNKNOWN.
 		 */
 		__vb2_queue_free(q, allocated_buffers);
 		mutex_unlock(&q->mmap_lock);
@@ -967,6 +999,14 @@
 	*count = allocated_buffers;
 
 	return 0;
+
+error:
+	if (no_previous_buffers) {
+		mutex_lock(&q->mmap_lock);
+		q->memory = VB2_MEMORY_UNKNOWN;
+		mutex_unlock(&q->mmap_lock);
+	}
+	return ret;
 }
 EXPORT_SYMBOL_GPL(vb2_core_create_bufs);
 
@@ -975,7 +1015,7 @@
 	if (plane_no >= vb->num_planes || !vb->planes[plane_no].mem_priv)
 		return NULL;
 
-	return call_ptr_memop(vb, vaddr, vb->planes[plane_no].mem_priv);
+	return call_ptr_memop(vaddr, vb, vb->planes[plane_no].mem_priv);
 
 }
 EXPORT_SYMBOL_GPL(vb2_plane_vaddr);
@@ -985,7 +1025,7 @@
 	if (plane_no >= vb->num_planes || !vb->planes[plane_no].mem_priv)
 		return NULL;
 
-	return call_ptr_memop(vb, cookie, vb->planes[plane_no].mem_priv);
+	return call_ptr_memop(cookie, vb, vb->planes[plane_no].mem_priv);
 }
 EXPORT_SYMBOL_GPL(vb2_plane_cookie);
 
@@ -1125,10 +1165,11 @@
 		vb->planes[plane].data_offset = 0;
 
 		/* Acquire each plane's memory */
-		mem_priv = call_ptr_memop(vb, get_userptr,
-				q->alloc_devs[plane] ? : q->dev,
-				planes[plane].m.userptr,
-				planes[plane].length, q->dma_dir);
+		mem_priv = call_ptr_memop(get_userptr,
+					  vb,
+					  q->alloc_devs[plane] ? : q->dev,
+					  planes[plane].m.userptr,
+					  planes[plane].length);
 		if (IS_ERR(mem_priv)) {
 			dprintk(q, 1, "failed acquiring userspace memory for plane %d\n",
 				plane);
@@ -1243,15 +1284,13 @@
 
 		/* Release previously acquired memory if present */
 		__vb2_plane_dmabuf_put(vb, &vb->planes[plane]);
-		vb->planes[plane].bytesused = 0;
-		vb->planes[plane].length = 0;
-		vb->planes[plane].m.fd = 0;
-		vb->planes[plane].data_offset = 0;
 
 		/* Acquire each plane's memory */
-		mem_priv = call_ptr_memop(vb, attach_dmabuf,
-				q->alloc_devs[plane] ? : q->dev,
-				dbuf, planes[plane].length, q->dma_dir);
+		mem_priv = call_ptr_memop(attach_dmabuf,
+					  vb,
+					  q->alloc_devs[plane] ? : q->dev,
+					  dbuf,
+					  planes[plane].length);
 		if (IS_ERR(mem_priv)) {
 			dprintk(q, 1, "failed to attach dmabuf\n");
 			ret = PTR_ERR(mem_priv);
@@ -2121,6 +2160,22 @@
 	unsigned int buffer, plane;
 
 	/*
+	 * Sanity checks to ensure the lock is held, MEMORY_MMAP is
+	 * used and fileio isn't active.
+	 */
+	lockdep_assert_held(&q->mmap_lock);
+
+	if (q->memory != VB2_MEMORY_MMAP) {
+		dprintk(q, 1, "queue is not currently set up for mmap\n");
+		return -EINVAL;
+	}
+
+	if (vb2_fileio_is_active(q)) {
+		dprintk(q, 1, "file io in progress\n");
+		return -EBUSY;
+	}
+
+	/*
 	 * Go over all buffers and their planes, comparing the given offset
 	 * with an offset assigned to each plane. If a match is found,
 	 * return its buffer and plane numbers.
@@ -2187,8 +2242,10 @@
 
 	vb_plane = &vb->planes[plane];
 
-	dbuf = call_ptr_memop(vb, get_dmabuf, vb_plane->mem_priv,
-				flags & O_ACCMODE);
+	dbuf = call_ptr_memop(get_dmabuf,
+			      vb,
+			      vb_plane->mem_priv,
+			      flags & O_ACCMODE);
 	if (IS_ERR_OR_NULL(dbuf)) {
 		dprintk(q, 1, "failed to export buffer %d, plane %d\n",
 			index, plane);
@@ -2219,11 +2276,6 @@
 	int ret;
 	unsigned long length;
 
-	if (q->memory != VB2_MEMORY_MMAP) {
-		dprintk(q, 1, "queue is not currently set up for mmap\n");
-		return -EINVAL;
-	}
-
 	/*
 	 * Check memory area access mode.
 	 */
@@ -2245,14 +2297,9 @@
 
 	mutex_lock(&q->mmap_lock);
 
-	if (vb2_fileio_is_active(q)) {
-		dprintk(q, 1, "mmap: file io in progress\n");
-		ret = -EBUSY;
-		goto unlock;
-	}
-
 	/*
-	 * Find the plane corresponding to the offset passed by userspace.
+	 * Find the plane corresponding to the offset passed by userspace. This
+	 * will return an error if not MEMORY_MMAP or file I/O is in progress.
 	 */
 	ret = __find_plane_by_offset(q, off, &buffer, &plane);
 	if (ret)
@@ -2305,22 +2352,25 @@
 	void *vaddr;
 	int ret;
 
-	if (q->memory != VB2_MEMORY_MMAP) {
-		dprintk(q, 1, "queue is not currently set up for mmap\n");
-		return -EINVAL;
-	}
+	mutex_lock(&q->mmap_lock);
 
 	/*
-	 * Find the plane corresponding to the offset passed by userspace.
+	 * Find the plane corresponding to the offset passed by userspace. This
+	 * will return an error if not MEMORY_MMAP or file I/O is in progress.
 	 */
 	ret = __find_plane_by_offset(q, off, &buffer, &plane);
 	if (ret)
-		return ret;
+		goto unlock;
 
 	vb = q->bufs[buffer];
 
 	vaddr = vb2_plane_vaddr(vb, plane);
+	mutex_unlock(&q->mmap_lock);
 	return vaddr ? (unsigned long)vaddr : -EINVAL;
+
+unlock:
+	mutex_unlock(&q->mmap_lock);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(vb2_get_unmapped_area);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/videobuf2/videobuf2-dma-contig.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/videobuf2/videobuf2-dma-contig.c
@@ -40,6 +40,8 @@
 
 	/* DMABUF related */
 	struct dma_buf_attachment	*db_attach;
+
+	struct vb2_buffer		*vb;
 };
 
 /*********************************************/
@@ -66,14 +68,14 @@
 /*         callbacks for all buffers         */
 /*********************************************/
 
-static void *vb2_dc_cookie(void *buf_priv)
+static void *vb2_dc_cookie(struct vb2_buffer *vb, void *buf_priv)
 {
 	struct vb2_dc_buf *buf = buf_priv;
 
 	return &buf->dma_addr;
 }
 
-static void *vb2_dc_vaddr(void *buf_priv)
+static void *vb2_dc_vaddr(struct vb2_buffer *vb, void *buf_priv)
 {
 	struct vb2_dc_buf *buf = buf_priv;
 	struct dma_buf_map map;
@@ -137,9 +139,9 @@
 	kfree(buf);
 }
 
-static void *vb2_dc_alloc(struct device *dev, unsigned long attrs,
-			  unsigned long size, enum dma_data_direction dma_dir,
-			  gfp_t gfp_flags)
+static void *vb2_dc_alloc(struct vb2_buffer *vb,
+			  struct device *dev,
+			  unsigned long size)
 {
 	struct vb2_dc_buf *buf;
 
@@ -150,11 +152,12 @@
 	if (!buf)
 		return ERR_PTR(-ENOMEM);
 
-	buf->attrs = attrs;
+	buf->attrs = vb->vb2_queue->dma_attrs;
 	buf->cookie = dma_alloc_attrs(dev, size, &buf->dma_addr,
-					GFP_KERNEL | gfp_flags, buf->attrs);
+				      GFP_KERNEL | vb->vb2_queue->gfp_flags,
+				      buf->attrs);
 	if (!buf->cookie) {
-		dev_err(dev, "dma_alloc_coherent of size %ld failed\n", size);
+		dev_err(dev, "dma_alloc_coherent of size %lu failed\n", size);
 		kfree(buf);
 		return ERR_PTR(-ENOMEM);
 	}
@@ -165,11 +168,12 @@
 	/* Prevent the device from being released while the buffer is used */
 	buf->dev = get_device(dev);
 	buf->size = size;
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 
 	buf->handler.refcount = &buf->refcount;
 	buf->handler.put = vb2_dc_put;
 	buf->handler.arg = buf;
+	buf->vb = vb;
 
 	refcount_set(&buf->refcount, 1);
 
@@ -200,9 +204,9 @@
 
 	vma->vm_ops->open(vma);
 
-	pr_debug("%s: mapped dma addr 0x%08lx at 0x%08lx, size %ld\n",
-		__func__, (unsigned long)buf->dma_addr, vma->vm_start,
-		buf->size);
+	pr_debug("%s: mapped dma addr 0x%08lx at 0x%08lx, size %lu\n",
+		 __func__, (unsigned long)buf->dma_addr, vma->vm_start,
+		 buf->size);
 
 	return 0;
 }
@@ -397,7 +401,9 @@
 	return sgt;
 }
 
-static struct dma_buf *vb2_dc_get_dmabuf(void *buf_priv, unsigned long flags)
+static struct dma_buf *vb2_dc_get_dmabuf(struct vb2_buffer *vb,
+					 void *buf_priv,
+					 unsigned long flags)
 {
 	struct vb2_dc_buf *buf = buf_priv;
 	struct dma_buf *dbuf;
@@ -459,8 +465,8 @@
 	kfree(buf);
 }
 
-static void *vb2_dc_get_userptr(struct device *dev, unsigned long vaddr,
-	unsigned long size, enum dma_data_direction dma_dir)
+static void *vb2_dc_get_userptr(struct vb2_buffer *vb, struct device *dev,
+				unsigned long vaddr, unsigned long size)
 {
 	struct vb2_dc_buf *buf;
 	struct frame_vector *vec;
@@ -490,7 +496,8 @@
 		return ERR_PTR(-ENOMEM);
 
 	buf->dev = dev;
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
+	buf->vb = vb;
 
 	offset = lower_32_bits(offset_in_page(vaddr));
 	vec = vb2_create_framevec(vaddr, size);
@@ -660,8 +667,8 @@
 	kfree(buf);
 }
 
-static void *vb2_dc_attach_dmabuf(struct device *dev, struct dma_buf *dbuf,
-	unsigned long size, enum dma_data_direction dma_dir)
+static void *vb2_dc_attach_dmabuf(struct vb2_buffer *vb, struct device *dev,
+				  struct dma_buf *dbuf, unsigned long size)
 {
 	struct vb2_dc_buf *buf;
 	struct dma_buf_attachment *dba;
@@ -677,6 +684,8 @@
 		return ERR_PTR(-ENOMEM);
 
 	buf->dev = dev;
+	buf->vb = vb;
+
 	/* create attachment for the dmabuf with the user device */
 	dba = dma_buf_attach(dbuf, buf->dev);
 	if (IS_ERR(dba)) {
@@ -685,7 +694,7 @@
 		return dba;
 	}
 
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	buf->size = size;
 	buf->db_attach = dba;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/videobuf2/videobuf2-dma-sg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/videobuf2/videobuf2-dma-sg.c
@@ -51,6 +51,8 @@
 	struct vb2_vmarea_handler	handler;
 
 	struct dma_buf_attachment	*db_attach;
+
+	struct vb2_buffer		*vb;
 };
 
 static void vb2_dma_sg_put(void *buf_priv);
@@ -96,9 +98,8 @@
 	return 0;
 }
 
-static void *vb2_dma_sg_alloc(struct device *dev, unsigned long dma_attrs,
-			      unsigned long size, enum dma_data_direction dma_dir,
-			      gfp_t gfp_flags)
+static void *vb2_dma_sg_alloc(struct vb2_buffer *vb, struct device *dev,
+			      unsigned long size)
 {
 	struct vb2_dma_sg_buf *buf;
 	struct sg_table *sgt;
@@ -113,7 +114,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	buf->vaddr = NULL;
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	buf->offset = 0;
 	buf->size = size;
 	/* size is already page aligned */
@@ -130,7 +131,7 @@
 	if (!buf->pages)
 		goto fail_pages_array_alloc;
 
-	ret = vb2_dma_sg_alloc_compacted(buf, gfp_flags);
+	ret = vb2_dma_sg_alloc_compacted(buf, vb->vb2_queue->gfp_flags);
 	if (ret)
 		goto fail_pages_alloc;
 
@@ -154,6 +155,7 @@
 	buf->handler.refcount = &buf->refcount;
 	buf->handler.put = vb2_dma_sg_put;
 	buf->handler.arg = buf;
+	buf->vb = vb;
 
 	refcount_set(&buf->refcount, 1);
 
@@ -213,9 +215,8 @@
 	dma_sync_sgtable_for_cpu(buf->dev, sgt, buf->dma_dir);
 }
 
-static void *vb2_dma_sg_get_userptr(struct device *dev, unsigned long vaddr,
-				    unsigned long size,
-				    enum dma_data_direction dma_dir)
+static void *vb2_dma_sg_get_userptr(struct vb2_buffer *vb, struct device *dev,
+				    unsigned long vaddr, unsigned long size)
 {
 	struct vb2_dma_sg_buf *buf;
 	struct sg_table *sgt;
@@ -230,10 +231,11 @@
 
 	buf->vaddr = NULL;
 	buf->dev = dev;
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	buf->offset = vaddr & ~PAGE_MASK;
 	buf->size = size;
 	buf->dma_sgt = &buf->sg_table;
+	buf->vb = vb;
 	vec = vb2_create_framevec(vaddr, size);
 	if (IS_ERR(vec))
 		goto userptr_fail_pfnvec;
@@ -292,7 +294,7 @@
 	kfree(buf);
 }
 
-static void *vb2_dma_sg_vaddr(void *buf_priv)
+static void *vb2_dma_sg_vaddr(struct vb2_buffer *vb, void *buf_priv)
 {
 	struct vb2_dma_sg_buf *buf = buf_priv;
 	struct dma_buf_map map;
@@ -511,7 +513,9 @@
 	.release = vb2_dma_sg_dmabuf_ops_release,
 };
 
-static struct dma_buf *vb2_dma_sg_get_dmabuf(void *buf_priv, unsigned long flags)
+static struct dma_buf *vb2_dma_sg_get_dmabuf(struct vb2_buffer *vb,
+					     void *buf_priv,
+					     unsigned long flags)
 {
 	struct vb2_dma_sg_buf *buf = buf_priv;
 	struct dma_buf *dbuf;
@@ -605,8 +609,8 @@
 	kfree(buf);
 }
 
-static void *vb2_dma_sg_attach_dmabuf(struct device *dev, struct dma_buf *dbuf,
-	unsigned long size, enum dma_data_direction dma_dir)
+static void *vb2_dma_sg_attach_dmabuf(struct vb2_buffer *vb, struct device *dev,
+				      struct dma_buf *dbuf, unsigned long size)
 {
 	struct vb2_dma_sg_buf *buf;
 	struct dma_buf_attachment *dba;
@@ -630,14 +634,15 @@
 		return dba;
 	}
 
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	buf->size = size;
 	buf->db_attach = dba;
+	buf->vb = vb;
 
 	return buf;
 }
 
-static void *vb2_dma_sg_cookie(void *buf_priv)
+static void *vb2_dma_sg_cookie(struct vb2_buffer *vb, void *buf_priv)
 {
 	struct vb2_dma_sg_buf *buf = buf_priv;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/common/videobuf2/videobuf2-vmalloc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/common/videobuf2/videobuf2-vmalloc.c
@@ -34,13 +34,12 @@
 
 static void vb2_vmalloc_put(void *buf_priv);
 
-static void *vb2_vmalloc_alloc(struct device *dev, unsigned long attrs,
-			       unsigned long size, enum dma_data_direction dma_dir,
-			       gfp_t gfp_flags)
+static void *vb2_vmalloc_alloc(struct vb2_buffer *vb, struct device *dev,
+			       unsigned long size)
 {
 	struct vb2_vmalloc_buf *buf;
 
-	buf = kzalloc(sizeof(*buf), GFP_KERNEL | gfp_flags);
+	buf = kzalloc(sizeof(*buf), GFP_KERNEL | vb->vb2_queue->gfp_flags);
 	if (!buf)
 		return ERR_PTR(-ENOMEM);
 
@@ -52,7 +51,7 @@
 		return ERR_PTR(-ENOMEM);
 	}
 
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	buf->handler.refcount = &buf->refcount;
 	buf->handler.put = vb2_vmalloc_put;
 	buf->handler.arg = buf;
@@ -71,9 +70,8 @@
 	}
 }
 
-static void *vb2_vmalloc_get_userptr(struct device *dev, unsigned long vaddr,
-				     unsigned long size,
-				     enum dma_data_direction dma_dir)
+static void *vb2_vmalloc_get_userptr(struct vb2_buffer *vb, struct device *dev,
+				     unsigned long vaddr, unsigned long size)
 {
 	struct vb2_vmalloc_buf *buf;
 	struct frame_vector *vec;
@@ -84,7 +82,7 @@
 	if (!buf)
 		return ERR_PTR(-ENOMEM);
 
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	offset = vaddr & ~PAGE_MASK;
 	buf->size = size;
 	vec = vb2_create_framevec(vaddr, size);
@@ -147,7 +145,7 @@
 	kfree(buf);
 }
 
-static void *vb2_vmalloc_vaddr(void *buf_priv)
+static void *vb2_vmalloc_vaddr(struct vb2_buffer *vb, void *buf_priv)
 {
 	struct vb2_vmalloc_buf *buf = buf_priv;
 
@@ -339,7 +337,9 @@
 	.release = vb2_vmalloc_dmabuf_ops_release,
 };
 
-static struct dma_buf *vb2_vmalloc_get_dmabuf(void *buf_priv, unsigned long flags)
+static struct dma_buf *vb2_vmalloc_get_dmabuf(struct vb2_buffer *vb,
+					      void *buf_priv,
+					      unsigned long flags)
 {
 	struct vb2_vmalloc_buf *buf = buf_priv;
 	struct dma_buf *dbuf;
@@ -403,8 +403,10 @@
 	kfree(buf);
 }
 
-static void *vb2_vmalloc_attach_dmabuf(struct device *dev, struct dma_buf *dbuf,
-	unsigned long size, enum dma_data_direction dma_dir)
+static void *vb2_vmalloc_attach_dmabuf(struct vb2_buffer *vb,
+				       struct device *dev,
+				       struct dma_buf *dbuf,
+				       unsigned long size)
 {
 	struct vb2_vmalloc_buf *buf;
 
@@ -416,7 +418,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	buf->dbuf = dbuf;
-	buf->dma_dir = dma_dir;
+	buf->dma_dir = vb->vb2_queue->dma_dir;
 	buf->size = size;
 
 	return buf;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dmxdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dmxdev.c
@@ -800,6 +800,11 @@
 	if (mutex_lock_interruptible(&dmxdev->mutex))
 		return -ERESTARTSYS;
 
+	if (dmxdev->exit) {
+		mutex_unlock(&dmxdev->mutex);
+		return -ENODEV;
+	}
+
 	for (i = 0; i < dmxdev->filternum; i++)
 		if (dmxdev->filter[i].state == DMXDEV_STATE_FREE)
 			break;
@@ -1413,7 +1418,7 @@
 };
 int dvb_dmxdev_init(struct dmxdev *dmxdev, struct dvb_adapter *dvb_adapter)
 {
-	int i;
+	int i, ret;
 
 	if (dmxdev->demux->open(dmxdev->demux) < 0)
 		return -EUSERS;
@@ -1432,21 +1437,36 @@
 					    DMXDEV_STATE_FREE);
 	}
 
-	dvb_register_device(dvb_adapter, &dmxdev->dvbdev, &dvbdev_demux, dmxdev,
+	ret = dvb_register_device(dvb_adapter, &dmxdev->dvbdev, &dvbdev_demux, dmxdev,
 			    DVB_DEVICE_DEMUX, dmxdev->filternum);
-	dvb_register_device(dvb_adapter, &dmxdev->dvr_dvbdev, &dvbdev_dvr,
+	if (ret < 0)
+		goto err_register_dvbdev;
+
+	ret = dvb_register_device(dvb_adapter, &dmxdev->dvr_dvbdev, &dvbdev_dvr,
 			    dmxdev, DVB_DEVICE_DVR, dmxdev->filternum);
+	if (ret < 0)
+		goto err_register_dvr_dvbdev;
 
 	dvb_ringbuffer_init(&dmxdev->dvr_buffer, NULL, 8192);
 
 	return 0;
+
+err_register_dvr_dvbdev:
+	dvb_unregister_device(dmxdev->dvbdev);
+err_register_dvbdev:
+	vfree(dmxdev->filter);
+	dmxdev->filter = NULL;
+	return ret;
 }
 
 EXPORT_SYMBOL(dvb_dmxdev_init);
 
 void dvb_dmxdev_release(struct dmxdev *dmxdev)
 {
+	mutex_lock(&dmxdev->mutex);
 	dmxdev->exit = 1;
+	mutex_unlock(&dmxdev->mutex);
+
 	if (dmxdev->dvbdev->users > 1) {
 		wait_event(dmxdev->dvbdev->wait_queue,
 				dmxdev->dvbdev->users == 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dvb_ca_en50221.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dvb_ca_en50221.c
@@ -151,13 +151,19 @@
 
 	/* mutex serializing ioctls */
 	struct mutex ioctl_mutex;
+
+	/* A mutex used when a device is disconnected */
+	struct mutex remove_mutex;
+
+	/* Whether the device is disconnected */
+	int exit;
 };
 
 static void dvb_ca_private_free(struct dvb_ca_private *ca)
 {
 	unsigned int i;
 
-	dvb_free_device(ca->dvbdev);
+	dvb_device_put(ca->dvbdev);
 	for (i = 0; i < ca->slot_count; i++)
 		vfree(ca->slot_info[i].rx_buffer.data);
 
@@ -187,7 +193,7 @@
 static int dvb_ca_en50221_read_data(struct dvb_ca_private *ca, int slot,
 				    u8 *ebuf, int ecount);
 static int dvb_ca_en50221_write_data(struct dvb_ca_private *ca, int slot,
-				     u8 *ebuf, int ecount);
+				     u8 *ebuf, int ecount, int size_write_flag);
 
 /**
  * findstr - Safely find needle in haystack.
@@ -370,7 +376,7 @@
 	ret = dvb_ca_en50221_wait_if_status(ca, slot, STATUSREG_FR, HZ / 10);
 	if (ret)
 		return ret;
-	ret = dvb_ca_en50221_write_data(ca, slot, buf, 2);
+	ret = dvb_ca_en50221_write_data(ca, slot, buf, 2, CMDREG_SW);
 	if (ret != 2)
 		return -EIO;
 	ret = ca->pub->write_cam_control(ca->pub, slot, CTRLIF_COMMAND, IRQEN);
@@ -778,11 +784,13 @@
  * @buf: The data in this buffer is treated as a complete link-level packet to
  *	 be written.
  * @bytes_write: Size of ebuf.
+ * @size_write_flag: A flag on Command Register which says whether the link size
+ * information will be writen or not.
  *
  * return: Number of bytes written, or < 0 on error.
  */
 static int dvb_ca_en50221_write_data(struct dvb_ca_private *ca, int slot,
-				     u8 *buf, int bytes_write)
+				     u8 *buf, int bytes_write, int size_write_flag)
 {
 	struct dvb_ca_slot *sl = &ca->slot_info[slot];
 	int status;
@@ -817,7 +825,7 @@
 
 	/* OK, set HC bit */
 	status = ca->pub->write_cam_control(ca->pub, slot, CTRLIF_COMMAND,
-					    IRQEN | CMDREG_HC);
+					    IRQEN | CMDREG_HC | size_write_flag);
 	if (status)
 		goto exit;
 
@@ -1508,7 +1516,7 @@
 
 			mutex_lock(&sl->slot_lock);
 			status = dvb_ca_en50221_write_data(ca, slot, fragbuf,
-							   fraglen + 2);
+							   fraglen + 2, 0);
 			mutex_unlock(&sl->slot_lock);
 			if (status == (fraglen + 2)) {
 				written = 1;
@@ -1709,12 +1717,22 @@
 
 	dprintk("%s\n", __func__);
 
-	if (!try_module_get(ca->pub->owner))
+	mutex_lock(&ca->remove_mutex);
+
+	if (ca->exit) {
+		mutex_unlock(&ca->remove_mutex);
+		return -ENODEV;
+	}
+
+	if (!try_module_get(ca->pub->owner)) {
+		mutex_unlock(&ca->remove_mutex);
 		return -EIO;
+	}
 
 	err = dvb_generic_open(inode, file);
 	if (err < 0) {
 		module_put(ca->pub->owner);
+		mutex_unlock(&ca->remove_mutex);
 		return err;
 	}
 
@@ -1739,6 +1757,7 @@
 
 	dvb_ca_private_get(ca);
 
+	mutex_unlock(&ca->remove_mutex);
 	return 0;
 }
 
@@ -1758,6 +1777,8 @@
 
 	dprintk("%s\n", __func__);
 
+	mutex_lock(&ca->remove_mutex);
+
 	/* mark the CA device as closed */
 	ca->open = 0;
 	dvb_ca_en50221_thread_update_delay(ca);
@@ -1768,6 +1789,13 @@
 
 	dvb_ca_private_put(ca);
 
+	if (dvbdev->users == 1 && ca->exit == 1) {
+		mutex_unlock(&ca->remove_mutex);
+		wake_up(&dvbdev->wait_queue);
+	} else {
+		mutex_unlock(&ca->remove_mutex);
+	}
+
 	return err;
 }
 
@@ -1891,6 +1919,7 @@
 	}
 
 	mutex_init(&ca->ioctl_mutex);
+	mutex_init(&ca->remove_mutex);
 
 	if (signal_pending(current)) {
 		ret = -EINTR;
@@ -1933,6 +1962,14 @@
 
 	dprintk("%s\n", __func__);
 
+	mutex_lock(&ca->remove_mutex);
+	ca->exit = 1;
+	mutex_unlock(&ca->remove_mutex);
+
+	if (ca->dvbdev->users < 1)
+		wait_event(ca->dvbdev->wait_queue,
+				ca->dvbdev->users == 1);
+
 	/* shutdown the thread if there was one */
 	kthread_stop(ca->thread);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dvb_demux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dvb_demux.c
@@ -125,12 +125,12 @@
 
 	cc = buf[3] & 0x0f;
 	ccok = ((feed->cc + 1) & 0x0f) == cc;
-	feed->cc = cc;
 	if (!ccok) {
 		set_buf_flags(feed, DMX_BUFFER_FLAG_DISCONTINUITY_DETECTED);
 		dprintk_sect_loss("missed packet: %d instead of %d!\n",
 				  cc, (feed->cc + 1) & 0x0f);
 	}
+	feed->cc = cc;
 
 	if (buf[1] & 0x40)	// PUSI ?
 		feed->peslen = 0xfffa;
@@ -310,7 +310,6 @@
 
 	cc = buf[3] & 0x0f;
 	ccok = ((feed->cc + 1) & 0x0f) == cc;
-	feed->cc = cc;
 
 	if (buf[3] & 0x20) {
 		/* adaption field present, check for discontinuity_indicator */
@@ -346,6 +345,7 @@
 		feed->pusi_seen = false;
 		dvb_dmx_swfilter_section_new(feed);
 	}
+	feed->cc = cc;
 
 	if (buf[1] & 0x40) {
 		/* PUSI=1 (is set), section boundary is here */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dvb_frontend.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dvb_frontend.c
@@ -136,7 +136,7 @@
 	struct dvb_frontend_private *fepriv = fe->frontend_priv;
 
 	if (fepriv)
-		dvb_free_device(fepriv->dvbdev);
+		dvb_device_put(fepriv->dvbdev);
 
 	dvb_frontend_invoke_release(fe, fe->ops.release);
 
@@ -293,14 +293,22 @@
 	}
 
 	if (events->eventw == events->eventr) {
-		int ret;
+		struct wait_queue_entry wait;
+		int ret = 0;
 
 		if (flags & O_NONBLOCK)
 			return -EWOULDBLOCK;
 
-		ret = wait_event_interruptible(events->wait_queue,
-					       dvb_frontend_test_event(fepriv, events));
-
+		init_waitqueue_entry(&wait, current);
+		add_wait_queue(&events->wait_queue, &wait);
+		while (!dvb_frontend_test_event(fepriv, events)) {
+			wait_woken(&wait, TASK_INTERRUPTIBLE, 0);
+			if (signal_pending(current)) {
+				ret = -ERESTARTSYS;
+				break;
+			}
+		}
+		remove_wait_queue(&events->wait_queue, &wait);
 		if (ret < 0)
 			return ret;
 	}
@@ -435,8 +443,8 @@
 
 		default:
 			fepriv->auto_step++;
-			fepriv->auto_sub_step = -1; /* it'll be incremented to 0 in a moment */
-			break;
+			fepriv->auto_sub_step = 0;
+			continue;
 		}
 
 		if (!ready) fepriv->auto_sub_step++;
@@ -2152,7 +2160,8 @@
 		if (!tvps->num || (tvps->num > DTV_IOCTL_MAX_MSGS))
 			return -EINVAL;
 
-		tvp = memdup_user(compat_ptr(tvps->props), tvps->num * sizeof(*tvp));
+		tvp = memdup_array_user(compat_ptr(tvps->props),
+					tvps->num, sizeof(*tvp));
 		if (IS_ERR(tvp))
 			return PTR_ERR(tvp);
 
@@ -2183,7 +2192,8 @@
 		if (!tvps->num || (tvps->num > DTV_IOCTL_MAX_MSGS))
 			return -EINVAL;
 
-		tvp = memdup_user(compat_ptr(tvps->props), tvps->num * sizeof(*tvp));
+		tvp = memdup_array_user(compat_ptr(tvps->props),
+					tvps->num, sizeof(*tvp));
 		if (IS_ERR(tvp))
 			return PTR_ERR(tvp);
 
@@ -2360,7 +2370,8 @@
 	if (!tvps->num || tvps->num > DTV_IOCTL_MAX_MSGS)
 		return -EINVAL;
 
-	tvp = memdup_user((void __user *)tvps->props, tvps->num * sizeof(*tvp));
+	tvp = memdup_array_user((void __user *)tvps->props,
+				tvps->num, sizeof(*tvp));
 	if (IS_ERR(tvp))
 		return PTR_ERR(tvp);
 
@@ -2438,7 +2449,8 @@
 		if (!tvps->num || (tvps->num > DTV_IOCTL_MAX_MSGS))
 			return -EINVAL;
 
-		tvp = memdup_user((void __user *)tvps->props, tvps->num * sizeof(*tvp));
+		tvp = memdup_array_user((void __user *)tvps->props,
+					tvps->num, sizeof(*tvp));
 		if (IS_ERR(tvp))
 			return PTR_ERR(tvp);
 
@@ -2985,6 +2997,7 @@
 		.name = fe->ops.info.name,
 #endif
 	};
+	int ret;
 
 	dev_dbg(dvb->device, "%s:\n", __func__);
 
@@ -3018,8 +3031,13 @@
 		 "DVB: registering adapter %i frontend %i (%s)...\n",
 		 fe->dvb->num, fe->id, fe->ops.info.name);
 
-	dvb_register_device(fe->dvb, &fepriv->dvbdev, &dvbdev_template,
+	ret = dvb_register_device(fe->dvb, &fepriv->dvbdev, &dvbdev_template,
 			    fe, DVB_DEVICE_FRONTEND, 0);
+	if (ret) {
+		dvb_frontend_put(fe);
+		mutex_unlock(&frontend_mutex);
+		return ret;
+	}
 
 	/*
 	 * Initialize the cache to the proper values according with the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dvb_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dvb_net.c
@@ -1564,15 +1564,43 @@
 	return dvb_usercopy(file, cmd, arg, dvb_net_do_ioctl);
 }
 
+static int locked_dvb_net_open(struct inode *inode, struct file *file)
+{
+	struct dvb_device *dvbdev = file->private_data;
+	struct dvb_net *dvbnet = dvbdev->priv;
+	int ret;
+
+	if (mutex_lock_interruptible(&dvbnet->remove_mutex))
+		return -ERESTARTSYS;
+
+	if (dvbnet->exit) {
+		mutex_unlock(&dvbnet->remove_mutex);
+		return -ENODEV;
+	}
+
+	ret = dvb_generic_open(inode, file);
+
+	mutex_unlock(&dvbnet->remove_mutex);
+
+	return ret;
+}
+
 static int dvb_net_close(struct inode *inode, struct file *file)
 {
 	struct dvb_device *dvbdev = file->private_data;
 	struct dvb_net *dvbnet = dvbdev->priv;
 
+	mutex_lock(&dvbnet->remove_mutex);
+
 	dvb_generic_release(inode, file);
 
-	if(dvbdev->users == 1 && dvbnet->exit == 1)
+	if (dvbdev->users == 1 && dvbnet->exit == 1) {
+		mutex_unlock(&dvbnet->remove_mutex);
 		wake_up(&dvbdev->wait_queue);
+	} else {
+		mutex_unlock(&dvbnet->remove_mutex);
+	}
+
 	return 0;
 }
 
@@ -1580,7 +1608,7 @@
 static const struct file_operations dvb_net_fops = {
 	.owner = THIS_MODULE,
 	.unlocked_ioctl = dvb_net_ioctl,
-	.open =	dvb_generic_open,
+	.open =	locked_dvb_net_open,
 	.release = dvb_net_close,
 	.llseek = noop_llseek,
 };
@@ -1599,10 +1627,13 @@
 {
 	int i;
 
+	mutex_lock(&dvbnet->remove_mutex);
 	dvbnet->exit = 1;
+	mutex_unlock(&dvbnet->remove_mutex);
+
 	if (dvbnet->dvbdev->users < 1)
 		wait_event(dvbnet->dvbdev->wait_queue,
-				dvbnet->dvbdev->users==1);
+				dvbnet->dvbdev->users == 1);
 
 	dvb_unregister_device(dvbnet->dvbdev);
 
@@ -1621,6 +1652,7 @@
 	int i;
 
 	mutex_init(&dvbnet->ioctl_mutex);
+	mutex_init(&dvbnet->remove_mutex);
 	dvbnet->demux = dmx;
 
 	for (i=0; i<DVB_NET_DEVICES_MAX; i++)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dvb_vb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dvb_vb2.c
@@ -358,6 +358,12 @@
 
 int dvb_vb2_querybuf(struct dvb_vb2_ctx *ctx, struct dmx_buffer *b)
 {
+	struct vb2_queue *q = &ctx->vb_q;
+
+	if (b->index >= q->num_buffers) {
+		dprintk(1, "[%s] buffer index out of range\n", ctx->name);
+		return -EINVAL;
+	}
 	vb2_core_querybuf(&ctx->vb_q, b->index, b);
 	dprintk(3, "[%s] index=%d\n", ctx->name, b->index);
 	return 0;
@@ -382,8 +388,13 @@
 
 int dvb_vb2_qbuf(struct dvb_vb2_ctx *ctx, struct dmx_buffer *b)
 {
+	struct vb2_queue *q = &ctx->vb_q;
 	int ret;
 
+	if (b->index >= q->num_buffers) {
+		dprintk(1, "[%s] buffer index out of range\n", ctx->name);
+		return -EINVAL;
+	}
 	ret = vb2_core_qbuf(&ctx->vb_q, b->index, b, NULL);
 	if (ret) {
 		dprintk(1, "[%s] index=%d errno=%d\n", ctx->name,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-core/dvbdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-core/dvbdev.c
@@ -37,6 +37,7 @@
 #include <media/tuner.h>
 
 static DEFINE_MUTEX(dvbdev_mutex);
+static LIST_HEAD(dvbdevfops_list);
 static int dvbdev_debug;
 
 module_param(dvbdev_debug, int, 0644);
@@ -95,10 +96,15 @@
 static int dvb_device_open(struct inode *inode, struct file *file)
 {
 	struct dvb_device *dvbdev;
+	unsigned int minor = iminor(inode);
+
+	if (minor >= MAX_DVB_MINORS)
+		return -ENODEV;
 
 	mutex_lock(&dvbdev_mutex);
 	down_read(&minor_rwsem);
-	dvbdev = dvb_minors[iminor(inode)];
+
+	dvbdev = dvb_minors[minor];
 
 	if (dvbdev && dvbdev->fops) {
 		int err = 0;
@@ -107,12 +113,14 @@
 		new_fops = fops_get(dvbdev->fops);
 		if (!new_fops)
 			goto fail;
-		file->private_data = dvbdev;
+		file->private_data = dvb_device_get(dvbdev);
 		replace_fops(file, new_fops);
 		if (file->f_op->open)
 			err = file->f_op->open(inode, file);
 		up_read(&minor_rwsem);
 		mutex_unlock(&dvbdev_mutex);
+		if (err)
+			dvb_device_put(dvbdev);
 		return err;
 	}
 fail:
@@ -171,6 +179,9 @@
 	}
 
 	dvbdev->users++;
+
+	dvb_device_put(dvbdev);
+
 	return 0;
 }
 EXPORT_SYMBOL(dvb_generic_release);
@@ -342,6 +353,7 @@
 				       GFP_KERNEL);
 		if (!dvbdev->pads) {
 			kfree(dvbdev->entity);
+			dvbdev->entity = NULL;
 			return -ENOMEM;
 		}
 	}
@@ -458,14 +470,15 @@
 			enum dvb_device_type type, int demux_sink_pads)
 {
 	struct dvb_device *dvbdev;
-	struct file_operations *dvbdevfops;
+	struct file_operations *dvbdevfops = NULL;
+	struct dvbdevfops_node *node = NULL, *new_node = NULL;
 	struct device *clsdev;
 	int minor;
 	int id, ret;
 
 	mutex_lock(&dvbdev_register_lock);
 
-	if ((id = dvbdev_get_free_id (adap, type)) < 0){
+	if ((id = dvbdev_get_free_id (adap, type)) < 0) {
 		mutex_unlock(&dvbdev_register_lock);
 		*pdvbdev = NULL;
 		pr_err("%s: couldn't find free device id\n", __func__);
@@ -473,84 +486,124 @@
 	}
 
 	*pdvbdev = dvbdev = kzalloc(sizeof(*dvbdev), GFP_KERNEL);
-
 	if (!dvbdev){
 		mutex_unlock(&dvbdev_register_lock);
 		return -ENOMEM;
 	}
 
-	dvbdevfops = kmemdup(template->fops, sizeof(*dvbdevfops), GFP_KERNEL);
+	/*
+	 * When a device of the same type is probe()d more than once,
+	 * the first allocated fops are used. This prevents memory leaks
+	 * that can occur when the same device is probe()d repeatedly.
+	 */
+	list_for_each_entry(node, &dvbdevfops_list, list_head) {
+		if (node->fops->owner == adap->module &&
+				node->type == type &&
+				node->template == template) {
+			dvbdevfops = node->fops;
+			break;
+		}
+	}
 
-	if (!dvbdevfops){
-		kfree (dvbdev);
-		mutex_unlock(&dvbdev_register_lock);
-		return -ENOMEM;
+	if (dvbdevfops == NULL) {
+		dvbdevfops = kmemdup(template->fops, sizeof(*dvbdevfops), GFP_KERNEL);
+		if (!dvbdevfops) {
+			kfree(dvbdev);
+			*pdvbdev = NULL;
+			mutex_unlock(&dvbdev_register_lock);
+			return -ENOMEM;
+		}
+
+		new_node = kzalloc(sizeof(struct dvbdevfops_node), GFP_KERNEL);
+		if (!new_node) {
+			kfree(dvbdevfops);
+			kfree(dvbdev);
+			*pdvbdev = NULL;
+			mutex_unlock(&dvbdev_register_lock);
+			return -ENOMEM;
+		}
+
+		new_node->fops = dvbdevfops;
+		new_node->type = type;
+		new_node->template = template;
+		list_add_tail (&new_node->list_head, &dvbdevfops_list);
 	}
 
 	memcpy(dvbdev, template, sizeof(struct dvb_device));
+	kref_init(&dvbdev->ref);
 	dvbdev->type = type;
 	dvbdev->id = id;
 	dvbdev->adapter = adap;
 	dvbdev->priv = priv;
 	dvbdev->fops = dvbdevfops;
 	init_waitqueue_head (&dvbdev->wait_queue);
-
 	dvbdevfops->owner = adap->module;
-
 	list_add_tail (&dvbdev->list_head, &adap->device_list);
-
 	down_write(&minor_rwsem);
 #ifdef CONFIG_DVB_DYNAMIC_MINORS
 	for (minor = 0; minor < MAX_DVB_MINORS; minor++)
 		if (dvb_minors[minor] == NULL)
 			break;
-
-	if (minor == MAX_DVB_MINORS) {
+#else
+	minor = nums2minor(adap->num, type, id);
+#endif
+	if (minor >= MAX_DVB_MINORS) {
+		if (new_node) {
+			list_del (&new_node->list_head);
+			kfree(dvbdevfops);
+			kfree(new_node);
+		}
 		list_del (&dvbdev->list_head);
-		kfree(dvbdevfops);
 		kfree(dvbdev);
+		*pdvbdev = NULL;
 		up_write(&minor_rwsem);
 		mutex_unlock(&dvbdev_register_lock);
 		return -EINVAL;
 	}
-#else
-	minor = nums2minor(adap->num, type, id);
-#endif
 
 	dvbdev->minor = minor;
-	dvb_minors[minor] = dvbdev;
+	dvb_minors[minor] = dvb_device_get(dvbdev);
 	up_write(&minor_rwsem);
-
 	ret = dvb_register_media_device(dvbdev, type, minor, demux_sink_pads);
 	if (ret) {
 		pr_err("%s: dvb_register_media_device failed to create the mediagraph\n",
 		      __func__);
-
+		if (new_node) {
+			list_del (&new_node->list_head);
+			kfree(dvbdevfops);
+			kfree(new_node);
+		}
 		dvb_media_device_free(dvbdev);
 		list_del (&dvbdev->list_head);
-		kfree(dvbdevfops);
 		kfree(dvbdev);
+		*pdvbdev = NULL;
 		mutex_unlock(&dvbdev_register_lock);
 		return ret;
 	}
 
-	mutex_unlock(&dvbdev_register_lock);
-
 	clsdev = device_create(dvb_class, adap->device,
 			       MKDEV(DVB_MAJOR, minor),
 			       dvbdev, "dvb%d.%s%d", adap->num, dnames[type], id);
 	if (IS_ERR(clsdev)) {
 		pr_err("%s: failed to create device dvb%d.%s%d (%ld)\n",
 		       __func__, adap->num, dnames[type], id, PTR_ERR(clsdev));
+		if (new_node) {
+			list_del (&new_node->list_head);
+			kfree(dvbdevfops);
+			kfree(new_node);
+		}
 		dvb_media_device_free(dvbdev);
 		list_del (&dvbdev->list_head);
-		kfree(dvbdevfops);
 		kfree(dvbdev);
+		*pdvbdev = NULL;
+		mutex_unlock(&dvbdev_register_lock);
 		return PTR_ERR(clsdev);
 	}
+
 	dprintk("DVB: register adapter%d/%s%d @ minor: %i (0x%02x)\n",
 		adap->num, dnames[type], id, minor, minor);
 
+	mutex_unlock(&dvbdev_register_lock);
 	return 0;
 }
 EXPORT_SYMBOL(dvb_register_device);
@@ -563,6 +616,7 @@
 
 	down_write(&minor_rwsem);
 	dvb_minors[dvbdev->minor] = NULL;
+	dvb_device_put(dvbdev);
 	up_write(&minor_rwsem);
 
 	dvb_media_device_free(dvbdev);
@@ -574,21 +628,33 @@
 EXPORT_SYMBOL(dvb_remove_device);
 
 
-void dvb_free_device(struct dvb_device *dvbdev)
+static void dvb_free_device(struct kref *ref)
 {
-	if (!dvbdev)
-		return;
+	struct dvb_device *dvbdev = container_of(ref, struct dvb_device, ref);
 
-	kfree (dvbdev->fops);
 	kfree (dvbdev);
 }
-EXPORT_SYMBOL(dvb_free_device);
+
+
+struct dvb_device *dvb_device_get(struct dvb_device *dvbdev)
+{
+	kref_get(&dvbdev->ref);
+	return dvbdev;
+}
+EXPORT_SYMBOL(dvb_device_get);
+
+
+void dvb_device_put(struct dvb_device *dvbdev)
+{
+	if (dvbdev)
+		kref_put(&dvbdev->ref, dvb_free_device);
+}
 
 
 void dvb_unregister_device(struct dvb_device *dvbdev)
 {
 	dvb_remove_device(dvbdev);
-	dvb_free_device(dvbdev);
+	dvb_device_put(dvbdev);
 }
 EXPORT_SYMBOL(dvb_unregister_device);
 
@@ -914,7 +980,7 @@
 		     int (*func)(struct file *file,
 		     unsigned int cmd, void *arg))
 {
-	char    sbuf[128];
+	char    sbuf[128] = {};
 	void    *mbuf = NULL;
 	void    *parg = NULL;
 	int     err  = -EINVAL;
@@ -1071,9 +1137,17 @@
 
 static void __exit exit_dvbdev(void)
 {
+	struct dvbdevfops_node *node, *next;
+
 	class_destroy(dvb_class);
 	cdev_del(&dvb_device_cdev);
 	unregister_chrdev_region(MKDEV(DVB_MAJOR, 0), MAX_DVB_MINORS);
+
+	list_for_each_entry_safe(node, next, &dvbdevfops_list, list_head) {
+		list_del (&node->list_head);
+		kfree(node->fops);
+		kfree(node);
+	}
 }
 
 subsys_initcall(init_dvbdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/as102_fe_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/as102_fe_types.h
@@ -174,6 +174,6 @@
 	uint32_t addr;
 	/* register mode access */
 	uint8_t mode;
-};
+} __packed;
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ascot2e.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ascot2e.c
@@ -533,7 +533,7 @@
 		priv->i2c_address, priv->i2c);
 	return fe;
 }
-EXPORT_SYMBOL(ascot2e_attach);
+EXPORT_SYMBOL_GPL(ascot2e_attach);
 
 MODULE_DESCRIPTION("Sony ASCOT2E terr/cab tuner driver");
 MODULE_AUTHOR("info@netup.ru");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/atbm8830.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/atbm8830.c
@@ -489,7 +489,7 @@
 	return NULL;
 
 }
-EXPORT_SYMBOL(atbm8830_attach);
+EXPORT_SYMBOL_GPL(atbm8830_attach);
 
 MODULE_DESCRIPTION("AltoBeam ATBM8830/8831 GB20600 demodulator driver");
 MODULE_AUTHOR("David T. L. Wong <davidtlwong@gmail.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/au8522_dig.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/au8522_dig.c
@@ -879,7 +879,7 @@
 	au8522_release_state(state);
 	return NULL;
 }
-EXPORT_SYMBOL(au8522_attach);
+EXPORT_SYMBOL_GPL(au8522_attach);
 
 static const struct dvb_frontend_ops au8522_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/bcm3510.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/bcm3510.c
@@ -649,6 +649,7 @@
 		deb_info("firmware chunk, addr: 0x%04x, len: 0x%04x, total length: 0x%04zx\n",addr,len,fw->size);
 		if ((ret = bcm3510_write_ram(st,addr,&b[i+4],len)) < 0) {
 			err("firmware download failed: %d\n",ret);
+			release_firmware(fw);
 			return ret;
 		}
 		i += 4 + len;
@@ -834,7 +835,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(bcm3510_attach);
+EXPORT_SYMBOL_GPL(bcm3510_attach);
 
 static const struct dvb_frontend_ops bcm3510_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx22700.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx22700.c
@@ -432,4 +432,4 @@
 MODULE_AUTHOR("Holger Waechtler");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(cx22700_attach);
+EXPORT_SYMBOL_GPL(cx22700_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx22702.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx22702.c
@@ -604,7 +604,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(cx22702_attach);
+EXPORT_SYMBOL_GPL(cx22702_attach);
 
 static const struct dvb_frontend_ops cx22702_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx24110.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx24110.c
@@ -653,4 +653,4 @@
 MODULE_AUTHOR("Peter Hettkamp");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(cx24110_attach);
+EXPORT_SYMBOL_GPL(cx24110_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx24113.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx24113.c
@@ -590,7 +590,7 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(cx24113_attach);
+EXPORT_SYMBOL_GPL(cx24113_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Activates frontend debugging (default:0)");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx24116.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx24116.c
@@ -741,6 +741,7 @@
 {
 	struct cx24116_state *state = fe->demodulator_priv;
 	u8 snr_reading;
+	int ret;
 	static const u32 snr_tab[] = { /* 10 x Table (rounded up) */
 		0x00000, 0x0199A, 0x03333, 0x04ccD, 0x06667,
 		0x08000, 0x0999A, 0x0b333, 0x0cccD, 0x0e667,
@@ -749,7 +750,11 @@
 
 	dprintk("%s()\n", __func__);
 
-	snr_reading = cx24116_readreg(state, CX24116_REG_QUALITY0);
+	ret = cx24116_readreg(state, CX24116_REG_QUALITY0);
+	if (ret  < 0)
+		return ret;
+
+	snr_reading = ret;
 
 	if (snr_reading >= 0xa0 /* 100% */)
 		*snr = 0xffff;
@@ -1133,7 +1138,7 @@
 	state->frontend.demodulator_priv = state;
 	return &state->frontend;
 }
-EXPORT_SYMBOL(cx24116_attach);
+EXPORT_SYMBOL_GPL(cx24116_attach);
 
 /*
  * Initialise or wake up device
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx24120.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx24120.c
@@ -305,7 +305,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(cx24120_attach);
+EXPORT_SYMBOL_GPL(cx24120_attach);
 
 static int cx24120_test_rom(struct cx24120_state *state)
 {
@@ -973,7 +973,9 @@
 	cmd.arg[8] = (clock_ratios_table[idx].rate >> 8) & 0xff;
 	cmd.arg[9] = (clock_ratios_table[idx].rate >> 0) & 0xff;
 
-	cx24120_message_send(state, &cmd);
+	ret = cx24120_message_send(state, &cmd);
+	if (ret != 0)
+		return;
 
 	/* Calculate ber window rates for stat work */
 	cx24120_calculate_ber_window(state, clock_ratios_table[idx].rate);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cx24123.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cx24123.c
@@ -1096,7 +1096,7 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(cx24123_attach);
+EXPORT_SYMBOL_GPL(cx24123_attach);
 
 static const struct dvb_frontend_ops cx24123_ops = {
 	.delsys = { SYS_DVBS },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cxd2820r_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cxd2820r_core.c
@@ -536,7 +536,7 @@
 
 	return pdata.get_dvb_frontend(client);
 }
-EXPORT_SYMBOL(cxd2820r_attach);
+EXPORT_SYMBOL_GPL(cxd2820r_attach);
 
 static struct dvb_frontend *cxd2820r_get_dvb_frontend(struct i2c_client *client)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cxd2841er.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cxd2841er.c
@@ -311,12 +311,8 @@
 
 static u32 cxd2841er_calc_iffreq_xtal(enum cxd2841er_xtal xtal, u32 ifhz)
 {
-	u64 tmp;
-
-	tmp = (u64) ifhz * 16777216;
-	do_div(tmp, ((xtal == SONY_XTAL_24000) ? 48000000 : 41000000));
-
-	return (u32) tmp;
+	return div_u64(ifhz * 16777216ull,
+		       (xtal == SONY_XTAL_24000) ? 48000000 : 41000000);
 }
 
 static u32 cxd2841er_calc_iffreq(u32 ifhz)
@@ -3930,14 +3926,14 @@
 {
 	return cxd2841er_attach(cfg, i2c, SYS_DVBS);
 }
-EXPORT_SYMBOL(cxd2841er_attach_s);
+EXPORT_SYMBOL_GPL(cxd2841er_attach_s);
 
 struct dvb_frontend *cxd2841er_attach_t_c(struct cxd2841er_config *cfg,
 					struct i2c_adapter *i2c)
 {
 	return cxd2841er_attach(cfg, i2c, 0);
 }
-EXPORT_SYMBOL(cxd2841er_attach_t_c);
+EXPORT_SYMBOL_GPL(cxd2841er_attach_t_c);
 
 static const struct dvb_frontend_ops cxd2841er_dvbs_s2_ops = {
 	.delsys = { SYS_DVBS, SYS_DVBS2 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/cxd2880/cxd2880_top.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/cxd2880/cxd2880_top.c
@@ -1950,7 +1950,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(cxd2880_attach);
+EXPORT_SYMBOL_GPL(cxd2880_attach);
 
 MODULE_DESCRIPTION("Sony CXD2880 DVB-T2/T tuner + demod driver");
 MODULE_AUTHOR("Sony Semiconductor Solutions Corporation");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib0070.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib0070.c
@@ -762,7 +762,7 @@
 	fe->tuner_priv = NULL;
 	return NULL;
 }
-EXPORT_SYMBOL(dib0070_attach);
+EXPORT_SYMBOL_GPL(dib0070_attach);
 
 MODULE_AUTHOR("Patrick Boettcher <patrick.boettcher@posteo.de>");
 MODULE_DESCRIPTION("Driver for the DiBcom 0070 base-band RF Tuner");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib0090.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib0090.c
@@ -2634,7 +2634,7 @@
 	return NULL;
 }
 
-EXPORT_SYMBOL(dib0090_register);
+EXPORT_SYMBOL_GPL(dib0090_register);
 
 struct dvb_frontend *dib0090_fw_register(struct dvb_frontend *fe, struct i2c_adapter *i2c, const struct dib0090_config *config)
 {
@@ -2660,7 +2660,7 @@
 	fe->tuner_priv = NULL;
 	return NULL;
 }
-EXPORT_SYMBOL(dib0090_fw_register);
+EXPORT_SYMBOL_GPL(dib0090_fw_register);
 
 MODULE_AUTHOR("Patrick Boettcher <patrick.boettcher@posteo.de>");
 MODULE_AUTHOR("Olivier Grenie <olivier.grenie@parrot.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib3000mb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib3000mb.c
@@ -51,7 +51,7 @@
 static int dib3000_read_reg(struct dib3000_state *state, u16 reg)
 {
 	u8 wb[] = { ((reg >> 8) | 0x80) & 0xff, reg & 0xff };
-	u8 rb[2];
+	u8 rb[2] = {};
 	struct i2c_msg msg[] = {
 		{ .addr = state->config.demod_address, .flags = 0,        .buf = wb, .len = 2 },
 		{ .addr = state->config.demod_address, .flags = I2C_M_RD, .buf = rb, .len = 2 },
@@ -815,4 +815,4 @@
 MODULE_DESCRIPTION(DRIVER_DESC);
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(dib3000mb_attach);
+EXPORT_SYMBOL_GPL(dib3000mb_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib3000mc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib3000mc.c
@@ -935,7 +935,7 @@
 	kfree(st);
 	return NULL;
 }
-EXPORT_SYMBOL(dib3000mc_attach);
+EXPORT_SYMBOL_GPL(dib3000mc_attach);
 
 static const struct dvb_frontend_ops dib3000mc_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib7000m.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib7000m.c
@@ -1434,7 +1434,7 @@
 	kfree(st);
 	return NULL;
 }
-EXPORT_SYMBOL(dib7000m_attach);
+EXPORT_SYMBOL_GPL(dib7000m_attach);
 
 static const struct dvb_frontend_ops dib7000m_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib7000p.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib7000p.c
@@ -497,7 +497,7 @@
 	prediv = reg_1856 & 0x3f;
 	loopdiv = (reg_1856 >> 6) & 0x3f;
 
-	if ((bw != NULL) && (bw->pll_prediv != prediv || bw->pll_ratio != loopdiv)) {
+	if (loopdiv && bw && (bw->pll_prediv != prediv || bw->pll_ratio != loopdiv)) {
 		dprintk("Updating pll (prediv: old =  %d new = %d ; loopdiv : old = %d new = %d)\n", prediv, bw->pll_prediv, loopdiv, bw->pll_ratio);
 		reg_1856 &= 0xf000;
 		reg_1857 = dib7000p_read_word(state, 1857);
@@ -2822,7 +2822,7 @@
 
 	return ops;
 }
-EXPORT_SYMBOL(dib7000p_attach);
+EXPORT_SYMBOL_GPL(dib7000p_attach);
 
 static const struct dvb_frontend_ops dib7000p_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib8000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib8000.c
@@ -2701,8 +2701,11 @@
 	u8 ratio;
 
 	if (state->revision == 0x8090) {
+		u32 internal = dib8000_read32(state, 23) / 1000;
+
 		ratio = 4;
-		unit_khz_dds_val = (1<<26) / (dib8000_read32(state, 23) / 1000);
+
+		unit_khz_dds_val = (1<<26) / (internal ?: 1);
 		if (offset_khz < 0)
 			dds = (1 << 26) - (abs_offset_khz * unit_khz_dds_val);
 		else
@@ -4473,8 +4476,10 @@
 
 	state->timf_default = cfg->pll->timf;
 
-	if (dib8000_identify(&state->i2c) == 0)
+	if (dib8000_identify(&state->i2c) == 0) {
+		kfree(fe);
 		goto error;
+	}
 
 	dibx000_init_i2c_master(&state->i2c_master, DIB8000, state->i2c.adap, state->i2c.addr);
 
@@ -4525,7 +4530,7 @@
 
 	return ops;
 }
-EXPORT_SYMBOL(dib8000_attach);
+EXPORT_SYMBOL_GPL(dib8000_attach);
 
 MODULE_AUTHOR("Olivier Grenie <Olivier.Grenie@parrot.com, Patrick Boettcher <patrick.boettcher@posteo.de>");
 MODULE_DESCRIPTION("Driver for the DiBcom 8000 ISDB-T demodulator");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dib9000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dib9000.c
@@ -2546,7 +2546,7 @@
 	kfree(st);
 	return NULL;
 }
-EXPORT_SYMBOL(dib9000_attach);
+EXPORT_SYMBOL_GPL(dib9000_attach);
 
 static const struct dvb_frontend_ops dib9000_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/drx39xyj/drxj.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/drx39xyj/drxj.c
@@ -12368,7 +12368,7 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(drx39xxj_attach);
+EXPORT_SYMBOL_GPL(drx39xxj_attach);
 
 static const struct dvb_frontend_ops drx39xxj_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/drxd_hard.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/drxd_hard.c
@@ -2947,7 +2947,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(drxd_attach);
+EXPORT_SYMBOL_GPL(drxd_attach);
 
 MODULE_DESCRIPTION("DRXD driver");
 MODULE_AUTHOR("Micronas");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/drxk_hard.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/drxk_hard.c
@@ -6673,7 +6673,7 @@
 static int drxk_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks)
 {
 	struct drxk_state *state = fe->demodulator_priv;
-	u16 err;
+	u16 err = 0;
 
 	dprintk(1, "\n");
 
@@ -6846,7 +6846,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(drxk_attach);
+EXPORT_SYMBOL_GPL(drxk_attach);
 
 MODULE_DESCRIPTION("DRX-K driver");
 MODULE_AUTHOR("Ralph Metzler");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ds3000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ds3000.c
@@ -859,7 +859,7 @@
 	ds3000_set_voltage(&state->frontend, SEC_VOLTAGE_OFF);
 	return &state->frontend;
 }
-EXPORT_SYMBOL(ds3000_attach);
+EXPORT_SYMBOL_GPL(ds3000_attach);
 
 static int ds3000_set_carrier_offset(struct dvb_frontend *fe,
 					s32 carrier_offset_khz)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/dvb-pll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/dvb-pll.c
@@ -866,7 +866,7 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(dvb_pll_attach);
+EXPORT_SYMBOL_GPL(dvb_pll_attach);
 
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ec100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ec100.c
@@ -299,7 +299,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(ec100_attach);
+EXPORT_SYMBOL_GPL(ec100_attach);
 
 static const struct dvb_frontend_ops ec100_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/helene.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/helene.c
@@ -1025,7 +1025,7 @@
 			priv->i2c_address, priv->i2c);
 	return fe;
 }
-EXPORT_SYMBOL(helene_attach_s);
+EXPORT_SYMBOL_GPL(helene_attach_s);
 
 struct dvb_frontend *helene_attach(struct dvb_frontend *fe,
 		const struct helene_config *config,
@@ -1061,7 +1061,7 @@
 			priv->i2c_address, priv->i2c);
 	return fe;
 }
-EXPORT_SYMBOL(helene_attach);
+EXPORT_SYMBOL_GPL(helene_attach);
 
 static int helene_probe(struct i2c_client *client,
 			const struct i2c_device_id *id)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/horus3a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/horus3a.c
@@ -395,7 +395,7 @@
 		priv->i2c_address, priv->i2c);
 	return fe;
 }
-EXPORT_SYMBOL(horus3a_attach);
+EXPORT_SYMBOL_GPL(horus3a_attach);
 
 MODULE_DESCRIPTION("Sony HORUS3A satellite tuner driver");
 MODULE_AUTHOR("Sergey Kozlov <serjk@netup.ru>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/isl6405.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/isl6405.c
@@ -141,7 +141,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(isl6405_attach);
+EXPORT_SYMBOL_GPL(isl6405_attach);
 
 MODULE_DESCRIPTION("Driver for lnb supply and control ic isl6405");
 MODULE_AUTHOR("Hartmut Hackmann & Oliver Endriss");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/isl6421.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/isl6421.c
@@ -213,7 +213,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(isl6421_attach);
+EXPORT_SYMBOL_GPL(isl6421_attach);
 
 MODULE_DESCRIPTION("Driver for lnb supply and control ic isl6421");
 MODULE_AUTHOR("Andrew de Quincey & Oliver Endriss");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/isl6423.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/isl6423.c
@@ -289,7 +289,7 @@
 	fe->sec_priv = NULL;
 	return NULL;
 }
-EXPORT_SYMBOL(isl6423_attach);
+EXPORT_SYMBOL_GPL(isl6423_attach);
 
 MODULE_DESCRIPTION("ISL6423 SEC");
 MODULE_AUTHOR("Manu Abraham");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/itd1000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/itd1000.c
@@ -389,7 +389,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(itd1000_attach);
+EXPORT_SYMBOL_GPL(itd1000_attach);
 
 MODULE_AUTHOR("Patrick Boettcher <pb@linuxtv.org>");
 MODULE_DESCRIPTION("Integrant ITD1000 driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ix2505v.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ix2505v.c
@@ -302,7 +302,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(ix2505v_attach);
+EXPORT_SYMBOL_GPL(ix2505v_attach);
 
 module_param_named(debug, ix2505v_debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/l64781.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/l64781.c
@@ -593,4 +593,4 @@
 MODULE_AUTHOR("Holger Waechtler, Marko Kohtala");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(l64781_attach);
+EXPORT_SYMBOL_GPL(l64781_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lg2160.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lg2160.c
@@ -1426,7 +1426,7 @@
 
 	return &state->frontend;
 }
-EXPORT_SYMBOL(lg2160_attach);
+EXPORT_SYMBOL_GPL(lg2160_attach);
 
 MODULE_DESCRIPTION("LG Electronics LG216x ATSC/MH Demodulator Driver");
 MODULE_AUTHOR("Michael Krufky <mkrufky@linuxtv.org>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lgdt3305.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lgdt3305.c
@@ -1148,7 +1148,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(lgdt3305_attach);
+EXPORT_SYMBOL_GPL(lgdt3305_attach);
 
 static const struct dvb_frontend_ops lgdt3304_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lgdt3306a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lgdt3306a.c
@@ -1859,7 +1859,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(lgdt3306a_attach);
+EXPORT_SYMBOL_GPL(lgdt3306a_attach);
 
 #ifdef DBG_DUMP
 
@@ -2177,6 +2177,11 @@
 	struct dvb_frontend *fe;
 	int ret;
 
+	if (!client->dev.platform_data) {
+		dev_err(&client->dev, "platform data is mandatory\n");
+		return -EINVAL;
+	}
+
 	config = kmemdup(client->dev.platform_data,
 			 sizeof(struct lgdt3306a_config), GFP_KERNEL);
 	if (config == NULL) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lgdt330x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lgdt330x.c
@@ -928,7 +928,7 @@
 
 	return lgdt330x_get_dvb_frontend(client);
 }
-EXPORT_SYMBOL(lgdt330x_attach);
+EXPORT_SYMBOL_GPL(lgdt330x_attach);
 
 static const struct dvb_frontend_ops lgdt3302_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lgs8gxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lgs8gxx.c
@@ -1043,7 +1043,7 @@
 	return NULL;
 
 }
-EXPORT_SYMBOL(lgs8gxx_attach);
+EXPORT_SYMBOL_GPL(lgs8gxx_attach);
 
 MODULE_DESCRIPTION("Legend Silicon LGS8913/LGS8GXX DMB-TH demodulator driver");
 MODULE_AUTHOR("David T. L. Wong <davidtlwong@gmail.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lnbh25.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lnbh25.c
@@ -173,7 +173,7 @@
 		__func__, priv->i2c_address);
 	return fe;
 }
-EXPORT_SYMBOL(lnbh25_attach);
+EXPORT_SYMBOL_GPL(lnbh25_attach);
 
 MODULE_DESCRIPTION("ST LNBH25 driver");
 MODULE_AUTHOR("info@netup.ru");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lnbp21.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lnbp21.c
@@ -155,7 +155,7 @@
 	return lnbx2x_attach(fe, i2c, override_set, override_clear,
 							i2c_addr, LNBH24_TTX);
 }
-EXPORT_SYMBOL(lnbh24_attach);
+EXPORT_SYMBOL_GPL(lnbh24_attach);
 
 struct dvb_frontend *lnbp21_attach(struct dvb_frontend *fe,
 				struct i2c_adapter *i2c, u8 override_set,
@@ -164,7 +164,7 @@
 	return lnbx2x_attach(fe, i2c, override_set, override_clear,
 							0x08, LNBP21_ISEL);
 }
-EXPORT_SYMBOL(lnbp21_attach);
+EXPORT_SYMBOL_GPL(lnbp21_attach);
 
 MODULE_DESCRIPTION("Driver for lnb supply and control ic lnbp21, lnbh24");
 MODULE_AUTHOR("Oliver Endriss, Igor M. Liplianin");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/lnbp22.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/lnbp22.c
@@ -125,7 +125,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(lnbp22_attach);
+EXPORT_SYMBOL_GPL(lnbp22_attach);
 
 MODULE_DESCRIPTION("Driver for lnb supply and control ic lnbp22");
 MODULE_AUTHOR("Dominik Kuhlen");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/m88ds3103.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/m88ds3103.c
@@ -1699,7 +1699,7 @@
 	*tuner_i2c_adapter = pdata.get_i2c_adapter(client);
 	return pdata.get_dvb_frontend(client);
 }
-EXPORT_SYMBOL(m88ds3103_attach);
+EXPORT_SYMBOL_GPL(m88ds3103_attach);
 
 static const struct dvb_frontend_ops m88ds3103_ops = {
 	.delsys = {SYS_DVBS, SYS_DVBS2},
@@ -1898,7 +1898,7 @@
 		/* get frontend address */
 		ret = regmap_read(dev->regmap, 0x29, &utmp);
 		if (ret)
-			goto err_kfree;
+			goto err_del_adapters;
 		dev->dt_addr = ((utmp & 0x80) == 0) ? 0x42 >> 1 : 0x40 >> 1;
 		dev_dbg(&client->dev, "dt addr is 0x%02x\n", dev->dt_addr);
 
@@ -1906,11 +1906,14 @@
 						      dev->dt_addr);
 		if (IS_ERR(dev->dt_client)) {
 			ret = PTR_ERR(dev->dt_client);
-			goto err_kfree;
+			goto err_del_adapters;
 		}
 	}
 
 	return 0;
+
+err_del_adapters:
+	i2c_mux_del_adapters(dev->muxc);
 err_kfree:
 	kfree(dev);
 err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/m88rs2000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/m88rs2000.c
@@ -808,7 +808,7 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(m88rs2000_attach);
+EXPORT_SYMBOL_GPL(m88rs2000_attach);
 
 MODULE_DESCRIPTION("M88RS2000 DVB-S Demodulator driver");
 MODULE_AUTHOR("Malcolm Priestley tvboxspy@gmail.com");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/mb86a16.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/mb86a16.c
@@ -1848,6 +1848,6 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(mb86a16_attach);
+EXPORT_SYMBOL_GPL(mb86a16_attach);
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Manu Abraham");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/mb86a20s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/mb86a20s.c
@@ -2081,7 +2081,7 @@
 	dev_info(&i2c->dev, "Detected a Fujitsu mb86a20s frontend\n");
 	return &state->frontend;
 }
-EXPORT_SYMBOL(mb86a20s_attach);
+EXPORT_SYMBOL_GPL(mb86a20s_attach);
 
 static const struct dvb_frontend_ops mb86a20s_ops = {
 	.delsys = { SYS_ISDBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/mn88443x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/mn88443x.c
@@ -204,11 +204,18 @@
 	struct regmap *regmap_t;
 };
 
-static void mn88443x_cmn_power_on(struct mn88443x_priv *chip)
+static int mn88443x_cmn_power_on(struct mn88443x_priv *chip)
 {
+	struct device *dev = &chip->client_s->dev;
 	struct regmap *r_t = chip->regmap_t;
+	int ret;
 
-	clk_prepare_enable(chip->mclk);
+	ret = clk_prepare_enable(chip->mclk);
+	if (ret) {
+		dev_err(dev, "Failed to prepare and enable mclk: %d\n",
+			ret);
+		return ret;
+	}
 
 	gpiod_set_value_cansleep(chip->reset_gpio, 1);
 	usleep_range(100, 1000);
@@ -222,6 +229,8 @@
 	} else {
 		regmap_write(r_t, HIZSET3, 0x8f);
 	}
+
+	return 0;
 }
 
 static void mn88443x_cmn_power_off(struct mn88443x_priv *chip)
@@ -738,7 +747,10 @@
 	chip->fe.demodulator_priv = chip;
 	i2c_set_clientdata(client, chip);
 
-	mn88443x_cmn_power_on(chip);
+	ret = mn88443x_cmn_power_on(chip);
+	if (ret)
+		goto err_i2c_t;
+
 	mn88443x_s_sleep(chip);
 	mn88443x_t_sleep(chip);
 
@@ -788,7 +800,7 @@
 static struct i2c_driver mn88443x_driver = {
 	.driver = {
 		.name = "mn88443x",
-		.of_match_table = of_match_ptr(mn88443x_of_match),
+		.of_match_table = mn88443x_of_match,
 	},
 	.probe    = mn88443x_probe,
 	.remove   = mn88443x_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/mt312.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/mt312.c
@@ -827,7 +827,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(mt312_attach);
+EXPORT_SYMBOL_GPL(mt312_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/mt352.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/mt352.c
@@ -593,4 +593,4 @@
 MODULE_AUTHOR("Holger Waechtler, Daniel Mack, Antonio Mancuso");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(mt352_attach);
+EXPORT_SYMBOL_GPL(mt352_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/mxl5xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/mxl5xx.c
@@ -1390,57 +1390,57 @@
 	u32 nco_count_min = 0;
 	u32 clk_type = 0;
 
-	struct MXL_REG_FIELD_T xpt_sync_polarity[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_sync_polarity[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700010, 8, 1}, {0x90700010, 9, 1},
 		{0x90700010, 10, 1}, {0x90700010, 11, 1},
 		{0x90700010, 12, 1}, {0x90700010, 13, 1},
 		{0x90700010, 14, 1}, {0x90700010, 15, 1} };
-	struct MXL_REG_FIELD_T xpt_clock_polarity[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_clock_polarity[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700010, 16, 1}, {0x90700010, 17, 1},
 		{0x90700010, 18, 1}, {0x90700010, 19, 1},
 		{0x90700010, 20, 1}, {0x90700010, 21, 1},
 		{0x90700010, 22, 1}, {0x90700010, 23, 1} };
-	struct MXL_REG_FIELD_T xpt_valid_polarity[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_valid_polarity[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700014, 0, 1}, {0x90700014, 1, 1},
 		{0x90700014, 2, 1}, {0x90700014, 3, 1},
 		{0x90700014, 4, 1}, {0x90700014, 5, 1},
 		{0x90700014, 6, 1}, {0x90700014, 7, 1} };
-	struct MXL_REG_FIELD_T xpt_ts_clock_phase[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_ts_clock_phase[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700018, 0, 3}, {0x90700018, 4, 3},
 		{0x90700018, 8, 3}, {0x90700018, 12, 3},
 		{0x90700018, 16, 3}, {0x90700018, 20, 3},
 		{0x90700018, 24, 3}, {0x90700018, 28, 3} };
-	struct MXL_REG_FIELD_T xpt_lsb_first[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_lsb_first[MXL_HYDRA_DEMOD_MAX] = {
 		{0x9070000C, 16, 1}, {0x9070000C, 17, 1},
 		{0x9070000C, 18, 1}, {0x9070000C, 19, 1},
 		{0x9070000C, 20, 1}, {0x9070000C, 21, 1},
 		{0x9070000C, 22, 1}, {0x9070000C, 23, 1} };
-	struct MXL_REG_FIELD_T xpt_sync_byte[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_sync_byte[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700010, 0, 1}, {0x90700010, 1, 1},
 		{0x90700010, 2, 1}, {0x90700010, 3, 1},
 		{0x90700010, 4, 1}, {0x90700010, 5, 1},
 		{0x90700010, 6, 1}, {0x90700010, 7, 1} };
-	struct MXL_REG_FIELD_T xpt_enable_output[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_enable_output[MXL_HYDRA_DEMOD_MAX] = {
 		{0x9070000C, 0, 1}, {0x9070000C, 1, 1},
 		{0x9070000C, 2, 1}, {0x9070000C, 3, 1},
 		{0x9070000C, 4, 1}, {0x9070000C, 5, 1},
 		{0x9070000C, 6, 1}, {0x9070000C, 7, 1} };
-	struct MXL_REG_FIELD_T xpt_err_replace_sync[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_err_replace_sync[MXL_HYDRA_DEMOD_MAX] = {
 		{0x9070000C, 24, 1}, {0x9070000C, 25, 1},
 		{0x9070000C, 26, 1}, {0x9070000C, 27, 1},
 		{0x9070000C, 28, 1}, {0x9070000C, 29, 1},
 		{0x9070000C, 30, 1}, {0x9070000C, 31, 1} };
-	struct MXL_REG_FIELD_T xpt_err_replace_valid[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_err_replace_valid[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700014, 8, 1}, {0x90700014, 9, 1},
 		{0x90700014, 10, 1}, {0x90700014, 11, 1},
 		{0x90700014, 12, 1}, {0x90700014, 13, 1},
 		{0x90700014, 14, 1}, {0x90700014, 15, 1} };
-	struct MXL_REG_FIELD_T xpt_continuous_clock[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_continuous_clock[MXL_HYDRA_DEMOD_MAX] = {
 		{0x907001D4, 0, 1}, {0x907001D4, 1, 1},
 		{0x907001D4, 2, 1}, {0x907001D4, 3, 1},
 		{0x907001D4, 4, 1}, {0x907001D4, 5, 1},
 		{0x907001D4, 6, 1}, {0x907001D4, 7, 1} };
-	struct MXL_REG_FIELD_T xpt_nco_clock_rate[MXL_HYDRA_DEMOD_MAX] = {
+	static const struct MXL_REG_FIELD_T xpt_nco_clock_rate[MXL_HYDRA_DEMOD_MAX] = {
 		{0x90700044, 16, 80}, {0x90700044, 16, 81},
 		{0x90700044, 16, 82}, {0x90700044, 16, 83},
 		{0x90700044, 16, 84}, {0x90700044, 16, 85},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/nxt200x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/nxt200x.c
@@ -1216,5 +1216,5 @@
 MODULE_AUTHOR("Kirk Lapray, Michael Krufky, Jean-Francois Thibert, and Taylor Jacob");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(nxt200x_attach);
+EXPORT_SYMBOL_GPL(nxt200x_attach);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/nxt6000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/nxt6000.c
@@ -621,4 +621,4 @@
 MODULE_AUTHOR("Florian Schirmer");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(nxt6000_attach);
+EXPORT_SYMBOL_GPL(nxt6000_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/or51132.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/or51132.c
@@ -605,4 +605,4 @@
 MODULE_AUTHOR("Trent Piepho");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(or51132_attach);
+EXPORT_SYMBOL_GPL(or51132_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/or51211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/or51211.c
@@ -551,5 +551,5 @@
 MODULE_AUTHOR("Kirk Lapray");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(or51211_attach);
+EXPORT_SYMBOL_GPL(or51211_attach);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/rtl2830.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/rtl2830.c
@@ -609,7 +609,7 @@
 		index, pid, onoff);
 
 	/* skip invalid PIDs (0x2000) */
-	if (pid > 0x1fff || index > 32)
+	if (pid > 0x1fff || index >= 32)
 		return 0;
 
 	if (onoff)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/rtl2832.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/rtl2832.c
@@ -983,7 +983,7 @@
 		index, pid, onoff, dev->slave_ts);
 
 	/* skip invalid PIDs (0x2000) */
-	if (pid > 0x1fff || index > 32)
+	if (pid > 0x1fff || index >= 32)
 		return 0;
 
 	if (onoff)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/s5h1409.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/s5h1409.c
@@ -981,7 +981,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(s5h1409_attach);
+EXPORT_SYMBOL_GPL(s5h1409_attach);
 
 static const struct dvb_frontend_ops s5h1409_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/s5h1411.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/s5h1411.c
@@ -900,7 +900,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(s5h1411_attach);
+EXPORT_SYMBOL_GPL(s5h1411_attach);
 
 static const struct dvb_frontend_ops s5h1411_ops = {
 	.delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/s5h1420.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/s5h1420.c
@@ -918,7 +918,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(s5h1420_attach);
+EXPORT_SYMBOL_GPL(s5h1420_attach);
 
 static const struct dvb_frontend_ops s5h1420_ops = {
 	.delsys = { SYS_DVBS },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/s5h1432.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/s5h1432.c
@@ -355,7 +355,7 @@
 
 	return &state->frontend;
 }
-EXPORT_SYMBOL(s5h1432_attach);
+EXPORT_SYMBOL_GPL(s5h1432_attach);
 
 static const struct dvb_frontend_ops s5h1432_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/s921.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/s921.c
@@ -495,7 +495,7 @@
 
 	return &state->frontend;
 }
-EXPORT_SYMBOL(s921_attach);
+EXPORT_SYMBOL_GPL(s921_attach);
 
 static const struct dvb_frontend_ops s921_ops = {
 	.delsys = { SYS_ISDBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/si21xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/si21xx.c
@@ -936,7 +936,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(si21xx_attach);
+EXPORT_SYMBOL_GPL(si21xx_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/sp887x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/sp887x.c
@@ -626,4 +626,4 @@
 MODULE_DESCRIPTION("Spase sp887x DVB-T demodulator driver");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(sp887x_attach);
+EXPORT_SYMBOL_GPL(sp887x_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stb0899_algo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stb0899_algo.c
@@ -269,7 +269,7 @@
 
 	short int derot_freq = 0, last_derot_freq = 0, derot_limit, next_loop = 3;
 	int index = 0;
-	u8 cfr[2];
+	u8 cfr[2] = {0};
 	u8 reg;
 
 	internal->status = NOCARRIER;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stb0899_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stb0899_drv.c
@@ -1638,7 +1638,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(stb0899_attach);
+EXPORT_SYMBOL_GPL(stb0899_attach);
 MODULE_PARM_DESC(verbose, "Set Verbosity level");
 MODULE_AUTHOR("Manu Abraham");
 MODULE_DESCRIPTION("STB0899 Multi-Std frontend");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stb6000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stb6000.c
@@ -232,7 +232,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(stb6000_attach);
+EXPORT_SYMBOL_GPL(stb6000_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stb6100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stb6100.c
@@ -557,7 +557,7 @@
 	kfree(state);
 }
 
-EXPORT_SYMBOL(stb6100_attach);
+EXPORT_SYMBOL_GPL(stb6100_attach);
 MODULE_PARM_DESC(verbose, "Set Verbosity level");
 
 MODULE_AUTHOR("Manu Abraham");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv0288.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv0288.c
@@ -440,9 +440,8 @@
 	struct stv0288_state *state = fe->demodulator_priv;
 	struct dtv_frontend_properties *c = &fe->dtv_property_cache;
 
-	char tm;
-	unsigned char tda[3];
-	u8 reg, time_out = 0;
+	u8 tda[3], reg, time_out = 0;
+	s8 tm;
 
 	dprintk("%s : FE_SET_FRONTEND\n", __func__);
 
@@ -591,7 +590,7 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(stv0288_attach);
+EXPORT_SYMBOL_GPL(stv0288_attach);
 
 module_param(debug_legacy_dish_switch, int, 0444);
 MODULE_PARM_DESC(debug_legacy_dish_switch,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv0297.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv0297.c
@@ -710,4 +710,4 @@
 MODULE_AUTHOR("Dennis Noermann and Andrew de Quincey");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(stv0297_attach);
+EXPORT_SYMBOL_GPL(stv0297_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv0299.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv0299.c
@@ -751,4 +751,4 @@
 MODULE_AUTHOR("Ralph Metzler, Holger Waechtler, Peter Schildmann, Felix Domke, Andreas Oberritter, Andrew de Quincey, Kenneth Aafly");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(stv0299_attach);
+EXPORT_SYMBOL_GPL(stv0299_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv0367.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv0367.c
@@ -118,50 +118,32 @@
 	}
 };
 
-static
-int stv0367_writeregs(struct stv0367_state *state, u16 reg, u8 *data, int len)
+static noinline_for_stack
+int stv0367_writereg(struct stv0367_state *state, u16 reg, u8 data)
 {
-	u8 buf[MAX_XFER_SIZE];
+	u8 buf[3] = { MSB(reg), LSB(reg), data };
 	struct i2c_msg msg = {
 		.addr = state->config->demod_address,
 		.flags = 0,
 		.buf = buf,
-		.len = len + 2
+		.len = 3,
 	};
 	int ret;
 
-	if (2 + len > sizeof(buf)) {
-		printk(KERN_WARNING
-		       "%s: i2c wr reg=%04x: len=%d is too big!\n",
-		       KBUILD_MODNAME, reg, len);
-		return -EINVAL;
-	}
-
-
-	buf[0] = MSB(reg);
-	buf[1] = LSB(reg);
-	memcpy(buf + 2, data, len);
-
 	if (i2cdebug)
 		printk(KERN_DEBUG "%s: [%02x] %02x: %02x\n", __func__,
-			state->config->demod_address, reg, buf[2]);
+			state->config->demod_address, reg, data);
 
 	ret = i2c_transfer(state->i2c, &msg, 1);
 	if (ret != 1)
 		printk(KERN_ERR "%s: i2c write error! ([%02x] %02x: %02x)\n",
-			__func__, state->config->demod_address, reg, buf[2]);
+			__func__, state->config->demod_address, reg, data);
 
 	return (ret != 1) ? -EREMOTEIO : 0;
 }
 
-static int stv0367_writereg(struct stv0367_state *state, u16 reg, u8 data)
-{
-	u8 tmp = data; /* see gcc.gnu.org/bugzilla/show_bug.cgi?id=81715 */
-
-	return stv0367_writeregs(state, reg, &tmp, 1);
-}
-
-static u8 stv0367_readreg(struct stv0367_state *state, u16 reg)
+static noinline_for_stack
+u8 stv0367_readreg(struct stv0367_state *state, u16 reg)
 {
 	u8 b0[] = { 0, 0 };
 	u8 b1[] = { 0 };
@@ -1750,7 +1732,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(stv0367ter_attach);
+EXPORT_SYMBOL_GPL(stv0367ter_attach);
 
 static int stv0367cab_gate_ctrl(struct dvb_frontend *fe, int enable)
 {
@@ -2923,7 +2905,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(stv0367cab_attach);
+EXPORT_SYMBOL_GPL(stv0367cab_attach);
 
 /*
  * Functions for operation on Digital Devices hardware
@@ -3344,7 +3326,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(stv0367ddb_attach);
+EXPORT_SYMBOL_GPL(stv0367ddb_attach);
 
 MODULE_PARM_DESC(debug, "Set debug");
 MODULE_PARM_DESC(i2c_debug, "Set i2c debug");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv0900_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv0900_core.c
@@ -1957,7 +1957,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(stv0900_attach);
+EXPORT_SYMBOL_GPL(stv0900_attach);
 
 MODULE_PARM_DESC(debug, "Set debug");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv090x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv090x.c
@@ -5073,7 +5073,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(stv090x_attach);
+EXPORT_SYMBOL_GPL(stv090x_attach);
 
 static const struct i2c_device_id stv090x_id_table[] = {
 	{"stv090x", 0},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv6110.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv6110.c
@@ -427,7 +427,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(stv6110_attach);
+EXPORT_SYMBOL_GPL(stv6110_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/stv6110x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/stv6110x.c
@@ -469,7 +469,7 @@
 	dev_info(&stv6110x->i2c->dev, "Attaching STV6110x\n");
 	return stv6110x->devctl;
 }
-EXPORT_SYMBOL(stv6110x_attach);
+EXPORT_SYMBOL_GPL(stv6110x_attach);
 
 static const struct i2c_device_id stv6110x_id_table[] = {
 	{"stv6110x", 0},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda10021.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda10021.c
@@ -523,4 +523,4 @@
 MODULE_AUTHOR("Ralph Metzler, Holger Waechtler, Markus Schulz");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(tda10021_attach);
+EXPORT_SYMBOL_GPL(tda10021_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda10023.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda10023.c
@@ -594,4 +594,4 @@
 MODULE_AUTHOR("Georg Acher, Hartmut Birr");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(tda10023_attach);
+EXPORT_SYMBOL_GPL(tda10023_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda10048.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda10048.c
@@ -410,6 +410,7 @@
 	struct tda10048_config *config = &state->config;
 	int i;
 	u32 if_freq_khz;
+	u64 sample_freq;
 
 	dprintk(1, "%s(bw = %d)\n", __func__, bw);
 
@@ -451,9 +452,11 @@
 	dprintk(1, "- pll_pfactor = %d\n", state->pll_pfactor);
 
 	/* Calculate the sample frequency */
-	state->sample_freq = state->xtal_hz * (state->pll_mfactor + 45);
-	state->sample_freq /= (state->pll_nfactor + 1);
-	state->sample_freq /= (state->pll_pfactor + 4);
+	sample_freq = state->xtal_hz;
+	sample_freq *= state->pll_mfactor + 45;
+	do_div(sample_freq, state->pll_nfactor + 1);
+	do_div(sample_freq, state->pll_pfactor + 4);
+	state->sample_freq = sample_freq;
 	dprintk(1, "- sample_freq = %d\n", state->sample_freq);
 
 	/* Update the I/F */
@@ -1138,7 +1141,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(tda10048_attach);
+EXPORT_SYMBOL_GPL(tda10048_attach);
 
 static const struct dvb_frontend_ops tda10048_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda1004x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda1004x.c
@@ -1378,5 +1378,5 @@
 MODULE_AUTHOR("Andrew de Quincey & Robert Schlabbach");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(tda10045_attach);
-EXPORT_SYMBOL(tda10046_attach);
+EXPORT_SYMBOL_GPL(tda10045_attach);
+EXPORT_SYMBOL_GPL(tda10046_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda10086.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda10086.c
@@ -764,4 +764,4 @@
 MODULE_AUTHOR("Andrew de Quincey");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(tda10086_attach);
+EXPORT_SYMBOL_GPL(tda10086_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda18271c2dd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda18271c2dd.c
@@ -328,7 +328,7 @@
 
 	OscFreq = (u64) freq * (u64) Div;
 	OscFreq *= (u64) 16384;
-	do_div(OscFreq, (u64)16000000);
+	do_div(OscFreq, 16000000);
 	MainDiv = OscFreq;
 
 	state->m_Regs[MPD] = PostDiv & 0x77;
@@ -352,7 +352,7 @@
 	OscFreq = (u64)freq * (u64)Div;
 	/* CalDiv = u32( OscFreq * 16384 / 16000000 ); */
 	OscFreq *= (u64)16384;
-	do_div(OscFreq, (u64)16000000);
+	do_div(OscFreq, 16000000);
 	CalDiv = OscFreq;
 
 	state->m_Regs[CPD] = PostDiv;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda665x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda665x.c
@@ -227,7 +227,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(tda665x_attach);
+EXPORT_SYMBOL_GPL(tda665x_attach);
 
 MODULE_DESCRIPTION("TDA665x driver");
 MODULE_AUTHOR("Manu Abraham");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda8083.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda8083.c
@@ -481,4 +481,4 @@
 MODULE_AUTHOR("Ralph Metzler, Holger Waechtler");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(tda8083_attach);
+EXPORT_SYMBOL_GPL(tda8083_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda8261.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda8261.c
@@ -188,7 +188,7 @@
 	return NULL;
 }
 
-EXPORT_SYMBOL(tda8261_attach);
+EXPORT_SYMBOL_GPL(tda8261_attach);
 
 MODULE_AUTHOR("Manu Abraham");
 MODULE_DESCRIPTION("TDA8261 8PSK/QPSK Tuner");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tda826x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tda826x.c
@@ -164,7 +164,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(tda826x_attach);
+EXPORT_SYMBOL_GPL(tda826x_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ts2020.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ts2020.c
@@ -525,7 +525,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(ts2020_attach);
+EXPORT_SYMBOL_GPL(ts2020_attach);
 
 /*
  * We implement own regmap locking due to legacy DVB attach which uses frontend
@@ -554,13 +554,19 @@
 		const struct i2c_device_id *id)
 {
 	struct ts2020_config *pdata = client->dev.platform_data;
-	struct dvb_frontend *fe = pdata->fe;
+	struct dvb_frontend *fe;
 	struct ts2020_priv *dev;
 	int ret;
 	u8 u8tmp;
 	unsigned int utmp;
 	char *chip_str;
 
+	if (!pdata) {
+		dev_err(&client->dev, "platform data is mandatory\n");
+		return -EINVAL;
+	}
+
+	fe = pdata->fe;
 	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
 	if (!dev) {
 		ret = -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/tua6100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/tua6100.c
@@ -186,7 +186,7 @@
 	fe->tuner_priv = priv;
 	return fe;
 }
-EXPORT_SYMBOL(tua6100_attach);
+EXPORT_SYMBOL_GPL(tua6100_attach);
 
 MODULE_DESCRIPTION("DVB tua6100 driver");
 MODULE_AUTHOR("Andrew de Quincey");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ves1820.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ves1820.c
@@ -434,4 +434,4 @@
 MODULE_AUTHOR("Ralph Metzler, Holger Waechtler");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(ves1820_attach);
+EXPORT_SYMBOL_GPL(ves1820_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/ves1x93.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/ves1x93.c
@@ -540,4 +540,4 @@
 MODULE_AUTHOR("Ralph Metzler");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(ves1x93_attach);
+EXPORT_SYMBOL_GPL(ves1x93_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/zl10036.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/zl10036.c
@@ -496,7 +496,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(zl10036_attach);
+EXPORT_SYMBOL_GPL(zl10036_attach);
 
 module_param_named(debug, zl10036_debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/zl10039.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/zl10039.c
@@ -295,7 +295,7 @@
 	kfree(state);
 	return NULL;
 }
-EXPORT_SYMBOL(zl10039_attach);
+EXPORT_SYMBOL_GPL(zl10039_attach);
 
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/dvb-frontends/zl10353.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/dvb-frontends/zl10353.c
@@ -665,4 +665,4 @@
 MODULE_AUTHOR("Chris Pascoe");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(zl10353_attach);
+EXPORT_SYMBOL_GPL(zl10353_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/firewire/firedtv-avc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/firewire/firedtv-avc.c
@@ -1165,7 +1165,11 @@
 		read_pos += program_info_length;
 		write_pos += program_info_length;
 	}
-	while (read_pos < length) {
+	while (read_pos + 4 < length) {
+		if (write_pos + 4 >= sizeof(c->operand) - 4) {
+			ret = -EINVAL;
+			goto out;
+		}
 		c->operand[write_pos++] = msg[read_pos++];
 		c->operand[write_pos++] = msg[read_pos++];
 		c->operand[write_pos++] = msg[read_pos++];
@@ -1177,13 +1181,17 @@
 		c->operand[write_pos++] = es_info_length >> 8;
 		c->operand[write_pos++] = es_info_length & 0xff;
 		if (es_info_length > 0) {
+			if (read_pos >= length) {
+				ret = -EINVAL;
+				goto out;
+			}
 			pmt_cmd_id = msg[read_pos++];
 			if (pmt_cmd_id != 1 && pmt_cmd_id != 4)
 				dev_err(fdtv->device, "invalid pmt_cmd_id %d at stream level\n",
 					pmt_cmd_id);
 
-			if (es_info_length > sizeof(c->operand) - 4 -
-					     write_pos) {
+			if (es_info_length > sizeof(c->operand) - 4 - write_pos ||
+			    es_info_length > length - read_pos) {
 				ret = -EINVAL;
 				goto out;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/firewire/firedtv-ci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/firewire/firedtv-ci.c
@@ -134,6 +134,8 @@
 	} else {
 		data_length = msg->msg[3];
 	}
+	if (data_length > sizeof(msg->msg) - data_pos)
+		return -EINVAL;
 
 	return avc_ca_pmt(fdtv, &msg->msg[data_pos], data_length);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/Kconfig
@@ -597,6 +597,7 @@
 config VIDEO_THS8200
 	tristate "Texas Instruments THS8200 video encoder"
 	depends on VIDEO_V4L2 && I2C
+	select V4L2_ASYNC
 	help
 	  Support for the Texas Instruments THS8200 video encoder.
 
@@ -631,6 +632,17 @@
 	  module will be called upd64083.
 endmenu
 
+config VIDEO_AP1302
+	tristate "ON Semiconductor AP1302 support"
+	depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor-level driver for the ON Semiconductor
+	  AP1302 ISP.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ap1302.
+
 menu "Audio/Video compression chips"
 	visible if !MEDIA_HIDE_ANCILLARY_SUBDRV
 
@@ -726,6 +738,18 @@
 config VIDEO_APTINA_PLL
 	tristate
 
+config VIDEO_AR1335
+       tristate "AR1335 sensor support"
+       depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+       depends on MEDIA_CAMERA_SUPPORT
+       select REGMAP_I2C
+       help
+         This is a driver for the AR1335 ON semiconductor camera
+         sensor.
+
+         To compile this driver as a module, choose M here: the
+         module will be called ar1335.
+
 config VIDEO_CCS_PLL
 	tristate
 
@@ -1389,6 +1413,75 @@
 	  This is a V4L2 sensor driver for Samsung S5C73M3
 	  8 Mpixel camera.
 
+config POWER_CTRL_LOGIC
+	tristate "power control logic driver"
+	depends on GPIO_ACPI
+	help
+	  This is a power control logic driver for sensor, the design
+	  depends on camera sensor connections.
+	  This driver controls power by getting and using managed GPIO
+	  pins from ACPI config for sensors, such as HM11B1, OV01A1S.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called power_ctrl_logic.
+
+config VIDEO_OV01A10
+	tristate "OmniVision OV01A10 sensor support"
+	depends on VIDEO_V4L2 && I2C
+	depends on ACPI || COMPILE_TEST
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the OmniVision
+	  OV01A10 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov01a10.
+
+config VIDEO_OV01A1S
+	tristate "OmniVision OV01A1S sensor support"
+	depends on POWER_CTRL_LOGIC
+	depends on VIDEO_V4L2 && I2C
+	depends on ACPI || COMPILE_TEST
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the OmniVision
+	  OV01A1S camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov01a1s.
+
+config VIDEO_OV02C10
+	tristate "OmniVision OV02C10 sensor support"
+	depends on VIDEO_V4L2 && I2C
+	depends on ACPI || COMPILE_TEST
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the OmniVision
+	  OV02C10 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov02c10.
+
+config VIDEO_HM11B1
+	tristate "Himax HM11B1 sensor support"
+	depends on POWER_CTRL_LOGIC
+	depends on VIDEO_V4L2 && I2C
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the Himax
+	  HM11B1 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hm11b1.
+
 endmenu
 
 menu "Lens drivers"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/Makefile
@@ -64,6 +64,8 @@
 obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
 obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
 obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
+obj-$(CONFIG_VIDEO_AP1302) += ap1302.o
+obj-$(CONFIG_VIDEO_AR1335) += ar1335.o
 obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
 obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
 obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
@@ -134,3 +136,9 @@
 obj-$(CONFIG_VIDEO_RDACM21)	+= rdacm21.o
 obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o
 obj-$(CONFIG_SDR_MAX2175) += max2175.o
+
+obj-$(CONFIG_VIDEO_HM11B1) += hm11b1.o
+obj-$(CONFIG_VIDEO_OV01A1S) += ov01a1s.o
+obj-$(CONFIG_VIDEO_OV01A10) += ov01a10.o
+obj-$(CONFIG_VIDEO_OV02C10) += ov02c10.o
+obj-$(CONFIG_POWER_CTRL_LOGIC) += power_ctrl_logic.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ad5820.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ad5820.c
@@ -327,18 +327,18 @@
 
 	ret = media_entity_pads_init(&coil->subdev.entity, 0, NULL);
 	if (ret < 0)
-		goto cleanup2;
+		goto clean_mutex;
 
 	ret = v4l2_async_register_subdev(&coil->subdev);
 	if (ret < 0)
-		goto cleanup;
+		goto clean_entity;
 
 	return ret;
 
-cleanup2:
-	mutex_destroy(&coil->power_lock);
-cleanup:
+clean_entity:
 	media_entity_cleanup(&coil->subdev.entity);
+clean_mutex:
+	mutex_destroy(&coil->power_lock);
 	return ret;
 }
 
@@ -357,7 +357,6 @@
 static const struct i2c_device_id ad5820_id_table[] = {
 	{ "ad5820", 0 },
 	{ "ad5821", 0 },
-	{ "ad5823", 0 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ad5820_id_table);
@@ -365,7 +364,6 @@
 static const struct of_device_id ad5820_of_table[] = {
 	{ .compatible = "adi,ad5820" },
 	{ .compatible = "adi,ad5821" },
-	{ .compatible = "adi,ad5823" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, ad5820_of_table);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/adv748x/adv748x-afe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/adv748x/adv748x-afe.c
@@ -521,6 +521,10 @@
 		}
 	}
 
+	adv748x_afe_s_input(afe, afe->input);
+
+	adv_dbg(state, "AFE Default input set to %d\n", afe->input);
+
 	/* Entity pads and sinks are 0-indexed to match the pads */
 	for (i = ADV748X_AFE_SINK_AIN0; i <= ADV748X_AFE_SINK_AIN7; i++)
 		afe->pads[i].flags = MEDIA_PAD_FL_SINK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/adv7511-v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/adv7511-v4l2.c
@@ -52,6 +52,7 @@
 #define ADV7511_MAX_HEIGHT 1200
 #define ADV7511_MIN_PIXELCLOCK 20000000
 #define ADV7511_MAX_PIXELCLOCK 225000000
+#define XYLON_LOGICVC_INTG
 
 #define ADV7511_MAX_ADDRS (3)
 
@@ -79,7 +80,50 @@
 	bool complete;
 };
 
+struct adv7511_in_params {
+	uint8_t input_id;
+	uint8_t input_style;
+	uint8_t input_color_depth;
+	uint8_t bit_justification;
+	uint8_t hsync_polarity;
+	uint8_t vsync_polarity;
+	uint8_t clock_delay;
+};
+
+struct adv7511_csc_coeff {
+	uint16_t a1;
+	uint16_t a2;
+	uint16_t a3;
+	uint16_t a4;
+	uint16_t b1;
+	uint16_t b2;
+	uint16_t b3;
+	uint16_t b4;
+	uint16_t c1;
+	uint16_t c2;
+	uint16_t c3;
+	uint16_t c4;
+};
+
+struct adv7511_out_params {
+	bool hdmi_mode;
+	uint8_t output_format;
+	uint8_t output_color_space;
+	uint8_t up_conversion;
+	uint8_t csc_enable;
+	uint8_t csc_scaling_factor;
+	struct adv7511_csc_coeff csc_coeff;
+};
+
+struct adv7511_config {
+	struct adv7511_in_params in_params;
+	struct adv7511_out_params out_params;
+	bool embedded_sync;
+	bool loaded;
+};
+
 struct adv7511_state {
+	struct adv7511_config cfg;
 	struct adv7511_platform_data pdata;
 	struct v4l2_subdev sd;
 	struct media_pad pad;
@@ -368,6 +412,10 @@
 {
 	struct adv7511_state *state = get_adv7511_state(sd);
 
+#ifdef XYLON_LOGICVC_INTG
+	return;
+#endif
+
 	/* Only makes sense for RGB formats */
 	if (state->fmt_code != MEDIA_BUS_FMT_RGB888_1X24) {
 		/* so just keep quantization */
@@ -544,7 +592,7 @@
 	buffer[3] = 0;
 	buffer[3] = hdmi_infoframe_checksum(buffer, len + 4);
 
-	if (hdmi_infoframe_unpack(&frame, buffer, sizeof(buffer)) < 0) {
+	if (hdmi_infoframe_unpack(&frame, buffer, len + 4) < 0) {
 		v4l2_err(sd, "%s: unpack of %s infoframe failed\n", __func__, cri->desc);
 		return;
 	}
@@ -1516,34 +1564,278 @@
 	adv7511_s_routing(sd, 0, 0, 0);
 }
 
+static void adv7511_set_ofdt_config(struct v4l2_subdev *sd)
+{
+	struct adv7511_state *state = get_adv7511_state(sd);
+	struct adv7511_config *config = &state->cfg;
+	uint8_t val_mask, val;
+	v4l2_dbg(1, debug, sd, "%s\n", __func__);
+
+	/* Input format */
+	val_mask = 0;
+	switch (config->in_params.input_id) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	case 2:
+		val = 0x02;
+		config->embedded_sync = true;
+		break;
+	case 3:
+		val = 0x03;
+		break;
+	case 4:
+		val = 0x04;
+		config->embedded_sync = true;
+		break;
+	case 5:
+		val = 0x05;
+		break;
+	case 6:
+		val = 0x06;
+		break;
+	case 7:
+		val = 0x07;
+		break;
+	case 8:
+		val = 0x08;
+		config->embedded_sync = true;
+		break;
+	}
+	val_mask |= val;
+	adv7511_wr(sd, 0x15, val_mask);
+
+	/* Output format */
+	val_mask = 0;
+	switch (config->out_params.output_color_space) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	}
+	val_mask |= (val << 0);
+	switch (config->in_params.input_style) {
+	case 1:
+		val = 0x02;
+		break;
+	case 2:
+		val = 0x01;
+		break;
+	case 3:
+		val = 0x03;
+		break;
+	default:
+		val = 0x00;
+		break;
+	}
+	val_mask |= (val << 2);
+	switch (config->in_params.input_color_depth) {
+	case 8:
+		val = 0x03;
+		break;
+	case 10:
+		val = 0x01;
+		break;
+	case 12:
+		val = 0x02;
+		break;
+	default:
+		val = 0x00;
+		break;
+	}
+	val_mask |= (val << 4);
+	switch (config->out_params.output_format) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	}
+	val_mask |= (val << 7);
+	adv7511_wr(sd, 0x16, val_mask);
+
+	/* H, V sync polarity, interpolation style */
+	val_mask = 0;
+	switch (config->out_params.up_conversion) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	}
+	val_mask |= (val << 2);
+	switch (config->in_params.hsync_polarity) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	}
+	val_mask |= (val << 5);
+	switch (config->in_params.vsync_polarity) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	}
+	val_mask |= (val << 6);
+	adv7511_wr(sd, 0x17, val_mask);
+
+	/* CSC mode, CSC coefficients */
+	if (config->out_params.csc_enable) {
+		switch (config->out_params.csc_scaling_factor) {
+		case 1:
+			val = 0x00;
+			break;
+		case 2:
+			val = 0x01;
+			break;
+		case 4:
+		default:
+			val = 0x02;
+			break;
+		}
+		adv7511_csc_conversion_mode(sd, val);
+		adv7511_csc_coeff(sd,
+				  config->out_params.csc_coeff.a1,
+				  config->out_params.csc_coeff.a2,
+				  config->out_params.csc_coeff.a3,
+				  config->out_params.csc_coeff.a4,
+				  config->out_params.csc_coeff.b1,
+				  config->out_params.csc_coeff.b2,
+				  config->out_params.csc_coeff.b3,
+				  config->out_params.csc_coeff.b4,
+				  config->out_params.csc_coeff.c1,
+				  config->out_params.csc_coeff.c2,
+				  config->out_params.csc_coeff.c3,
+				  config->out_params.csc_coeff.c4);
+		/* enable CSC */
+		adv7511_wr_and_or(sd, 0x18, 0x7f, 0x80);
+		/* AVI infoframe: Limited range RGB (16-235) */
+		adv7511_wr_and_or(sd, 0x57, 0xf3, 0x04);
+	}
+
+	/* AVI Info, Audio Info */
+	adv7511_wr_and_or(sd, 0x44, 0xe7, 0x10);
+
+	/* Video input justification */
+	val_mask = 0;
+	switch (config->in_params.bit_justification) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	case 2:
+		val = 0x02;
+		break;
+	}
+	val_mask |= (val << 3);
+	adv7511_wr(sd, 0x48, val_mask);
+
+	/* Output format */
+	val_mask = 0x00;
+	if (config->out_params.output_format == 1) {
+		if (config->out_params.output_color_space == 0)
+			val_mask = 0x02;
+		else if (config->out_params.output_format == 1)
+			val_mask = 0x01;
+	}
+	val_mask <<= 5;
+	adv7511_wr(sd, 0x55, val_mask);
+
+	/* Picture format aspect ratio */
+	adv7511_wr(sd, 0x56, 0x28);
+
+	/* HDCP, Frame encryption, HDMI/DVI */
+	val_mask = 0x04;
+	if (config->out_params.hdmi_mode)
+		val_mask |= 0x02;
+	adv7511_wr(sd, 0xaf, val_mask);
+
+	/* Capture for input video clock */
+	val_mask = 0;
+	switch (config->in_params.clock_delay) {
+	default:
+	case 0:
+		val = 0x00;
+		break;
+	case 1:
+		val = 0x01;
+		break;
+	case 2:
+		val = 0x02;
+		break;
+	case 3:
+		val = 0x03;
+		break;
+	case 4:
+		val = 0x04;
+		break;
+	case 5:
+		val = 0x05;
+		break;
+	case 6:
+		val = 0x06;
+		break;
+	case 7:
+		val = 0x07;
+		break;
+	}
+	val_mask |= (val << 5);
+	adv7511_wr_and_or(sd, 0xba, 0x1f, val_mask);
+}
+
 /* Configure hdmi transmitter. */
 static void adv7511_setup(struct v4l2_subdev *sd)
 {
 	struct adv7511_state *state = get_adv7511_state(sd);
 	v4l2_dbg(1, debug, sd, "%s\n", __func__);
 
-	/* Input format: RGB 4:4:4 */
-	adv7511_wr_and_or(sd, 0x15, 0xf0, 0x0);
-	/* Output format: RGB 4:4:4 */
-	adv7511_wr_and_or(sd, 0x16, 0x7f, 0x0);
-	/* 1st order interpolation 4:2:2 -> 4:4:4 up conversion, Aspect ratio: 16:9 */
-	adv7511_wr_and_or(sd, 0x17, 0xf9, 0x06);
-	/* Disable pixel repetition */
-	adv7511_wr_and_or(sd, 0x3b, 0x9f, 0x0);
-	/* Disable CSC */
-	adv7511_wr_and_or(sd, 0x18, 0x7f, 0x0);
-	/* Output format: RGB 4:4:4, Active Format Information is valid,
-	 * underscanned */
-	adv7511_wr_and_or(sd, 0x55, 0x9c, 0x12);
-	/* AVI Info frame packet enable, Audio Info frame disable */
-	adv7511_wr_and_or(sd, 0x44, 0xe7, 0x10);
-	/* Colorimetry, Active format aspect ratio: same as picure. */
-	adv7511_wr(sd, 0x56, 0xa8);
-	/* No encryption */
-	adv7511_wr_and_or(sd, 0xaf, 0xed, 0x0);
+	if (!state->cfg.loaded) {
+		/* Input format: RGB 4:4:4 */
+		adv7511_wr_and_or(sd, 0x15, 0xf0, 0x0);
+		/* Output format: RGB 4:4:4 */
+		adv7511_wr_and_or(sd, 0x16, 0x7f, 0x0);
+		/* 1st order interpolation 4:2:2 -> 4:4:4 up conversion, Aspect ratio: 16:9 */
+		adv7511_wr_and_or(sd, 0x17, 0xf9, 0x06);
+		/* Disable pixel repetition */
+		adv7511_wr_and_or(sd, 0x3b, 0x9f, 0x0);
+		/* Disable CSC */
+		adv7511_wr_and_or(sd, 0x18, 0x7f, 0x0);
+		/* Output format: RGB 4:4:4, Active Format Information is valid,
+		* underscanned */
+		adv7511_wr_and_or(sd, 0x55, 0x9c, 0x12);
+		/* AVI Info frame packet enable, Audio Info frame disable */
+		adv7511_wr_and_or(sd, 0x44, 0xe7, 0x10);
+		/* Colorimetry, Active format aspect ratio: same as picure. */
+		adv7511_wr(sd, 0x56, 0xa8);
+		/* No encryption */
+		adv7511_wr_and_or(sd, 0xaf, 0xed, 0x0);
 
-	/* Positive clk edge capture for input video clock */
-	adv7511_wr_and_or(sd, 0xba, 0x1f, 0x60);
+		/* Positive clk edge capture for input video clock */
+		adv7511_wr_and_or(sd, 0xba, 0x1f, 0x60);
+	} else {
+		adv7511_set_ofdt_config(sd);
+	}
 
 	adv7511_audio_setup(sd);
 
@@ -1786,6 +2078,181 @@
 	adv7511_cec_write(sd, 0x4e, ratio << 2);
 }
 
+
+static void adv7511_get_ofdt_config(struct i2c_client *client,
+	struct adv7511_state *state)
+{
+	struct device_node *dn = client->dev.of_node;
+	struct device_node *np;
+	struct adv7511_config *config = &state->cfg;
+	u32 const *prop;
+	int size;
+	bool vin_loaded, vout_loaded;
+
+	vin_loaded = vout_loaded = false;
+
+	prop = of_get_property(dn, "edid-addr", &size);
+	if (prop)
+		state->pdata.i2c_edid = (uint8_t)be32_to_cpup(prop);
+
+	prop = of_get_property(dn, "pktmem-addr", &size);
+	if (prop)
+		state->pdata.i2c_pktmem = (uint8_t)be32_to_cpup(prop);
+
+	prop = of_get_property(dn, "cec-addr", &size);
+	if (prop)
+		state->pdata.i2c_cec = (uint8_t)be32_to_cpup(prop);
+
+	np = of_find_node_by_name(dn, "video-input");
+	if (np) {
+		prop = of_get_property(np, "input-id", &size);
+		if (prop)
+			config->in_params.input_id =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "input-style", &size);
+		if (prop)
+			config->in_params.input_style =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "input-color-depth", &size);
+		if (prop)
+			config->in_params.input_color_depth =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "bit-justification", &size);
+		if (prop)
+			config->in_params.bit_justification =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "hsync-polarity", &size);
+		if (prop)
+			config->in_params.hsync_polarity =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "vsync-polarity", &size);
+		if (prop)
+			config->in_params.vsync_polarity =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "clock-delay", &size);
+		if (prop)
+			config->in_params.clock_delay =
+				(uint8_t)be32_to_cpup(prop);
+		vin_loaded = true;
+	} else {
+		pr_info("No video input configuration, using device default\n");
+	}
+
+	np = of_find_node_by_name(dn, "video-output");
+	if (np) {
+		prop = of_get_property(np, "hdmi-mode", &size);
+		if (prop) {
+			if (be32_to_cpup(prop) == 1)
+				config->out_params.hdmi_mode = true;
+		}
+		prop = of_get_property(np, "output-format", &size);
+		if (prop)
+			config->out_params.output_format =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "output-color-space", &size);
+		if (prop)
+			config->out_params.output_color_space =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "up-conversion", &size);
+		if (prop)
+			config->out_params.up_conversion =
+				(uint8_t)be32_to_cpup(prop);
+		prop = of_get_property(np, "csc-enable", &size);
+		if (prop)
+			config->out_params.csc_enable =
+				(uint8_t)be32_to_cpup(prop);
+		if (config->out_params.csc_enable) {
+			prop = of_get_property(np, "csc-scaling-factor", &size);
+			if (prop) {
+				config->out_params.csc_scaling_factor =
+					(uint8_t)be32_to_cpup(prop);
+			}
+			np = of_find_node_by_name(dn, "csc-coefficients");
+			if (np) {
+				prop = of_get_property(np, "a1", &size);
+				if (prop) {
+					config->out_params.csc_coeff.a1 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "a2", &size);
+				if (prop) {
+					config->out_params.csc_coeff.a2 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "a3", &size);
+				if (prop) {
+					config->out_params.csc_coeff.a3 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "a4", &size);
+				if (prop) {
+					config->out_params.csc_coeff.a4 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "b1", &size);
+				if (prop) {
+					config->out_params.csc_coeff.b1 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "b2", &size);
+				if (prop) {
+					config->out_params.csc_coeff.b2 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "b3", &size);
+				if (prop) {
+					config->out_params.csc_coeff.b3 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "b4", &size);
+				if (prop) {
+					config->out_params.csc_coeff.b4 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "c1", &size);
+				if (prop) {
+					config->out_params.csc_coeff.c1 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "c2", &size);
+				if (prop) {
+					config->out_params.csc_coeff.c2 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "c3", &size);
+				if (prop) {
+					config->out_params.csc_coeff.c3 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+				prop = of_get_property(np, "c4", &size);
+				if (prop) {
+					config->out_params.csc_coeff.c4 =
+						(uint16_t)be32_to_cpup(prop);
+				}
+			} else {
+				pr_info("No CSC coefficients, using default\n");
+			}
+		}
+		vout_loaded = true;
+	} else {
+		pr_info("No video output configuration, using device default\n");
+	}
+
+	if (vin_loaded && vout_loaded)
+		config->loaded = true;
+}
+
+struct v4l2_subdev *adv7511_subdev(struct v4l2_subdev *sd)
+{
+	static struct v4l2_subdev *subdev;
+
+	if (sd)
+		subdev = sd;
+
+	return subdev;
+}
+EXPORT_SYMBOL(adv7511_subdev);
+
 static int adv7511_probe(struct i2c_client *client, const struct i2c_device_id *id)
 {
 	struct adv7511_state *state;
@@ -1803,11 +2270,17 @@
 	if (!state)
 		return -ENOMEM;
 
-	/* Platform data */
-	if (!pdata) {
-		v4l_err(client, "No platform data!\n");
-		return -ENODEV;
+	if (client->dev.of_node) {
+		adv7511_get_ofdt_config(client, state);
+	} else {
+		/* Platform data */
+		if (!pdata) {
+			v4l_err(client, "No platform data!\n");
+			return -ENODEV;
+		}
+		memcpy(&state->pdata, pdata, sizeof(state->pdata));
 	}
+
 	memcpy(&state->pdata, pdata, sizeof(state->pdata));
 	state->fmt_code = MEDIA_BUS_FMT_RGB888_1X24;
 	state->colorspace = V4L2_COLORSPACE_SRGB;
@@ -1818,6 +2291,7 @@
 			 client->addr << 1);
 
 	v4l2_i2c_subdev_init(sd, client, &adv7511_ops);
+	adv7511_subdev(sd);
 	sd->internal_ops = &adv7511_int_ops;
 
 	hdl = &state->hdl;
@@ -1911,7 +2385,9 @@
 
 	INIT_DELAYED_WORK(&state->edid_handler, adv7511_edid_handler);
 
+#ifndef XYLON_LOGICVC_INTG
 	adv7511_init_setup(sd);
+#endif
 
 #if IS_ENABLED(CONFIG_VIDEO_ADV7511_CEC)
 	state->cec_adap = cec_allocate_adapter(&adv7511_cec_adap_ops,
@@ -1925,8 +2401,9 @@
 #endif
 
 	adv7511_set_isr(sd, true);
+#ifndef XYLON_LOGICVC_INTG
 	adv7511_check_monitor_present_status(sd);
-
+#endif
 	v4l2_info(sd, "%s found @ 0x%x (%s)\n", client->name,
 			  client->addr << 1, client->adapter->name);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/adv7604.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/adv7604.c
@@ -1405,12 +1405,13 @@
 	if (v4l2_detect_cvt(stdi->lcf + 1, hfreq, stdi->lcvs, 0,
 			(stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) |
 			(stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0),
-			false, timings))
+			false, adv76xx_get_dv_timings_cap(sd, -1), timings))
 		return 0;
 	if (v4l2_detect_gtf(stdi->lcf + 1, hfreq, stdi->lcvs,
 			(stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) |
 			(stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0),
-			false, state->aspect_ratio, timings))
+			false, state->aspect_ratio,
+			adv76xx_get_dv_timings_cap(sd, -1), timings))
 		return 0;
 
 	v4l2_dbg(2, debug, sd,
@@ -2484,7 +2485,7 @@
 		buffer[i + 3] = infoframe_read(sd,
 				       adv76xx_cri[index].payload_addr + i);
 
-	if (hdmi_infoframe_unpack(frame, buffer, sizeof(buffer)) < 0) {
+	if (hdmi_infoframe_unpack(frame, buffer, len + 3) < 0) {
 		v4l2_err(sd, "%s: unpack of %s infoframe failed\n", __func__,
 			 adv76xx_cri[index].desc);
 		return -ENOENT;
@@ -2517,10 +2518,10 @@
 	const struct adv76xx_chip_info *info = state->info;
 	struct v4l2_dv_timings timings;
 	struct stdi_readback stdi;
-	u8 reg_io_0x02 = io_read(sd, 0x02);
+	int ret;
+	u8 reg_io_0x02;
 	u8 edid_enabled;
 	u8 cable_det;
-
 	static const char * const csc_coeff_sel_rb[16] = {
 		"bypassed", "YPbPr601 -> RGB", "reserved", "YPbPr709 -> RGB",
 		"reserved", "RGB -> YPbPr601", "reserved", "RGB -> YPbPr709",
@@ -2619,13 +2620,21 @@
 	v4l2_info(sd, "-----Color space-----\n");
 	v4l2_info(sd, "RGB quantization range ctrl: %s\n",
 			rgb_quantization_range_txt[state->rgb_quantization_range]);
-	v4l2_info(sd, "Input color space: %s\n",
-			input_color_space_txt[reg_io_0x02 >> 4]);
-	v4l2_info(sd, "Output color space: %s %s, alt-gamma %s\n",
-			(reg_io_0x02 & 0x02) ? "RGB" : "YCbCr",
-			(((reg_io_0x02 >> 2) & 0x01) ^ (reg_io_0x02 & 0x01)) ?
-				"(16-235)" : "(0-255)",
-			(reg_io_0x02 & 0x08) ? "enabled" : "disabled");
+
+	ret = io_read(sd, 0x02);
+	if (ret < 0) {
+		v4l2_info(sd, "Can't read Input/Output color space\n");
+	} else {
+		reg_io_0x02 = ret;
+
+		v4l2_info(sd, "Input color space: %s\n",
+				input_color_space_txt[reg_io_0x02 >> 4]);
+		v4l2_info(sd, "Output color space: %s %s, alt-gamma %s\n",
+				(reg_io_0x02 & 0x02) ? "RGB" : "YCbCr",
+				(((reg_io_0x02 >> 2) & 0x01) ^ (reg_io_0x02 & 0x01)) ?
+					"(16-235)" : "(0-255)",
+				(reg_io_0x02 & 0x08) ? "enabled" : "disabled");
+	}
 	v4l2_info(sd, "Color space conversion: %s\n",
 			csc_coeff_sel_rb[cp_read(sd, info->cp_csc) >> 4]);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/adv7842.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/adv7842.c
@@ -1441,14 +1441,15 @@
 	}
 
 	if (v4l2_detect_cvt(stdi->lcf + 1, hfreq, stdi->lcvs, 0,
-			(stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) |
-			(stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0),
-			false, timings))
+			    (stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) |
+			    (stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0),
+			    false, adv7842_get_dv_timings_cap(sd), timings))
 		return 0;
 	if (v4l2_detect_gtf(stdi->lcf + 1, hfreq, stdi->lcvs,
-			(stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) |
-			(stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0),
-			false, state->aspect_ratio, timings))
+			    (stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) |
+			    (stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0),
+			    false, state->aspect_ratio,
+			    adv7842_get_dv_timings_cap(sd), timings))
 		return 0;
 
 	v4l2_dbg(2, debug, sd,
@@ -2593,7 +2594,7 @@
 	for (i = 0; i < len; i++)
 		buffer[i + 3] = infoframe_read(sd, cri->payload_addr + i);
 
-	if (hdmi_infoframe_unpack(&frame, buffer, sizeof(buffer)) < 0) {
+	if (hdmi_infoframe_unpack(&frame, buffer, len + 3) < 0) {
 		v4l2_err(sd, "%s: unpack of %s infoframe failed\n", __func__, cri->desc);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ap1302.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ap1302.c
@@ -0,0 +1,2997 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Driver for the AP1302 external camera ISP from ON Semiconductor
+ *
+ * Copyright (C) 2021, Witekio, Inc.
+ * Copyright (C) 2021, Xilinx, Inc.
+ * Copyright (C) 2021, Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/media.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#include <media/media-entity.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+
+#define DRIVER_NAME "ap1302"
+
+#define AP1302_FW_WINDOW_SIZE			0x2000
+#define AP1302_FW_WINDOW_OFFSET			0x8000
+
+#define AP1302_MIN_WIDTH			24U
+#define AP1302_MIN_HEIGHT			16U
+#define AP1302_MAX_WIDTH			4224U
+#define AP1302_MAX_HEIGHT			4092U
+
+#define AP1302_REG_16BIT(n)			((2 << 24) | (n))
+#define AP1302_REG_32BIT(n)			((4 << 24) | (n))
+#define AP1302_REG_SIZE(n)			((n) >> 24)
+#define AP1302_REG_ADDR(n)			((n) & 0x0000ffff)
+#define AP1302_REG_PAGE(n)			((n) & 0x00ff0000)
+#define AP1302_REG_PAGE_MASK			0x00ff0000
+
+/* Info Registers */
+#define AP1302_CHIP_VERSION			AP1302_REG_16BIT(0x0000)
+#define AP1302_CHIP_ID				0x0265
+#define AP1302_FRAME_CNT			AP1302_REG_16BIT(0x0002)
+#define AP1302_ERROR				AP1302_REG_16BIT(0x0006)
+#define AP1302_ERR_FILE				AP1302_REG_32BIT(0x0008)
+#define AP1302_ERR_LINE				AP1302_REG_16BIT(0x000c)
+#define AP1302_SIPM_ERR_0			AP1302_REG_16BIT(0x0014)
+#define AP1302_SIPM_ERR_1			AP1302_REG_16BIT(0x0016)
+#define AP1302_CHIP_REV				AP1302_REG_16BIT(0x0050)
+#define AP1302_CON_BUF(n)			AP1302_REG_16BIT(0x0a2c + (n))
+#define AP1302_CON_BUF_SIZE			512
+
+/* Control Registers */
+#define AP1302_DZ_TGT_FCT			AP1302_REG_16BIT(0x1010)
+#define AP1302_SFX_MODE				AP1302_REG_16BIT(0x1016)
+#define AP1302_SFX_MODE_SFX_NORMAL		(0U << 0)
+#define AP1302_SFX_MODE_SFX_ALIEN		(1U << 0)
+#define AP1302_SFX_MODE_SFX_ANTIQUE		(2U << 0)
+#define AP1302_SFX_MODE_SFX_BW			(3U << 0)
+#define AP1302_SFX_MODE_SFX_EMBOSS		(4U << 0)
+#define AP1302_SFX_MODE_SFX_EMBOSS_COLORED	(5U << 0)
+#define AP1302_SFX_MODE_SFX_GRAYSCALE		(6U << 0)
+#define AP1302_SFX_MODE_SFX_NEGATIVE		(7U << 0)
+#define AP1302_SFX_MODE_SFX_BLUISH		(8U << 0)
+#define AP1302_SFX_MODE_SFX_GREENISH		(9U << 0)
+#define AP1302_SFX_MODE_SFX_REDISH		(10U << 0)
+#define AP1302_SFX_MODE_SFX_POSTERIZE1		(11U << 0)
+#define AP1302_SFX_MODE_SFX_POSTERIZE2		(12U << 0)
+#define AP1302_SFX_MODE_SFX_SEPIA1		(13U << 0)
+#define AP1302_SFX_MODE_SFX_SEPIA2		(14U << 0)
+#define AP1302_SFX_MODE_SFX_SKETCH		(15U << 0)
+#define AP1302_SFX_MODE_SFX_SOLARIZE		(16U << 0)
+#define AP1302_SFX_MODE_SFX_FOGGY		(17U << 0)
+#define AP1302_BUBBLE_OUT_FMT			AP1302_REG_16BIT(0x1164)
+#define AP1302_BUBBLE_OUT_FMT_FT_YUV		(3U << 4)
+#define AP1302_BUBBLE_OUT_FMT_FT_RGB		(4U << 4)
+#define AP1302_BUBBLE_OUT_FMT_FT_YUV_JFIF	(5U << 4)
+#define AP1302_BUBBLE_OUT_FMT_FST_RGB_888	(0U << 0)
+#define AP1302_BUBBLE_OUT_FMT_FST_RGB_565	(1U << 0)
+#define AP1302_BUBBLE_OUT_FMT_FST_RGB_555M	(2U << 0)
+#define AP1302_BUBBLE_OUT_FMT_FST_RGB_555L	(3U << 0)
+#define AP1302_BUBBLE_OUT_FMT_FST_YUV_422	(0U << 0)
+#define AP1302_BUBBLE_OUT_FMT_FST_YUV_420	(1U << 0)
+#define AP1302_BUBBLE_OUT_FMT_FST_YUV_400	(2U << 0)
+#define AP1302_ATOMIC				AP1302_REG_16BIT(0x1184)
+#define AP1302_ATOMIC_MODE			BIT(2)
+#define AP1302_ATOMIC_FINISH			BIT(1)
+#define AP1302_ATOMIC_RECORD			BIT(0)
+
+/*
+ * Preview Context Registers (preview_*). AP1302 supports 3 "contexts"
+ * (Preview, Snapshot, Video). These can be programmed for different size,
+ * format, FPS, etc. There is no functional difference between the contexts,
+ * so the only potential benefit of using them is reduced number of register
+ * writes when switching output modes (if your concern is atomicity, see
+ * "atomic" register).
+ * So there's virtually no benefit in using contexts for this driver and it
+ * would significantly increase complexity. Let's use preview context only.
+ */
+#define AP1302_PREVIEW_WIDTH			AP1302_REG_16BIT(0x2000)
+#define AP1302_PREVIEW_HEIGHT			AP1302_REG_16BIT(0x2002)
+#define AP1302_PREVIEW_ROI_X0			AP1302_REG_16BIT(0x2004)
+#define AP1302_PREVIEW_ROI_Y0			AP1302_REG_16BIT(0x2006)
+#define AP1302_PREVIEW_ROI_X1			AP1302_REG_16BIT(0x2008)
+#define AP1302_PREVIEW_ROI_Y1			AP1302_REG_16BIT(0x200a)
+#define AP1302_PREVIEW_OUT_FMT			AP1302_REG_16BIT(0x2012)
+#define AP1302_PREVIEW_OUT_FMT_IPIPE_BYPASS	BIT(13)
+#define AP1302_PREVIEW_OUT_FMT_SS		BIT(12)
+#define AP1302_PREVIEW_OUT_FMT_FAKE_EN		BIT(11)
+#define AP1302_PREVIEW_OUT_FMT_ST_EN		BIT(10)
+#define AP1302_PREVIEW_OUT_FMT_IIS_NONE		(0U << 8)
+#define AP1302_PREVIEW_OUT_FMT_IIS_POST_VIEW	(1U << 8)
+#define AP1302_PREVIEW_OUT_FMT_IIS_VIDEO	(2U << 8)
+#define AP1302_PREVIEW_OUT_FMT_IIS_BUBBLE	(3U << 8)
+#define AP1302_PREVIEW_OUT_FMT_FT_JPEG_422	(0U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_JPEG_420	(1U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_YUV		(3U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_RGB		(4U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_YUV_JFIF	(5U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_RAW8		(8U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_RAW10		(9U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_RAW12		(10U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_RAW16		(11U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_DNG8		(12U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_DNG10		(13U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_DNG12		(14U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FT_DNG16		(15U << 4)
+#define AP1302_PREVIEW_OUT_FMT_FST_JPEG_ROTATE	BIT(2)
+#define AP1302_PREVIEW_OUT_FMT_FST_JPEG_SCAN	(0U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_JPEG_JFIF	(1U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_JPEG_EXIF	(2U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RGB_888	(0U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RGB_565	(1U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RGB_555M	(2U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RGB_555L	(3U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_YUV_422	(0U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_YUV_420	(1U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_YUV_400	(2U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_SENSOR	(0U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_CAPTURE	(1U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_CP	(2U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_BPC	(3U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_IHDR	(4U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_PP	(5U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_DENSH	(6U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_PM	(7U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_GC	(8U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_CURVE	(9U << 0)
+#define AP1302_PREVIEW_OUT_FMT_FST_RAW_CCONV	(10U << 0)
+#define AP1302_PREVIEW_S1_SENSOR_MODE		AP1302_REG_16BIT(0x202e)
+#define AP1302_PREVIEW_HINF_CTRL		AP1302_REG_16BIT(0x2030)
+#define AP1302_PREVIEW_HINF_CTRL_BT656_LE	BIT(15)
+#define AP1302_PREVIEW_HINF_CTRL_BT656_16BIT	BIT(14)
+#define AP1302_PREVIEW_HINF_CTRL_MUX_DELAY(n)	((n) << 8)
+#define AP1302_PREVIEW_HINF_CTRL_LV_POL		BIT(7)
+#define AP1302_PREVIEW_HINF_CTRL_FV_POL		BIT(6)
+#define AP1302_PREVIEW_HINF_CTRL_MIPI_CONT_CLK	BIT(5)
+#define AP1302_PREVIEW_HINF_CTRL_SPOOF		BIT(4)
+#define AP1302_PREVIEW_HINF_CTRL_MIPI_MODE	BIT(3)
+#define AP1302_PREVIEW_HINF_CTRL_MIPI_LANES(n)	((n) << 0)
+
+/* IQ Registers */
+#define AP1302_AE_CTRL			AP1302_REG_16BIT(0x5002)
+#define AP1302_AE_CTRL_STATS_SEL		BIT(11)
+#define AP1302_AE_CTRL_IMM				BIT(10)
+#define AP1302_AE_CTRL_ROUND_ISO		BIT(9)
+#define AP1302_AE_CTRL_UROI_FACE		BIT(7)
+#define AP1302_AE_CTRL_UROI_LOCK		BIT(6)
+#define AP1302_AE_CTRL_UROI_BOUND		BIT(5)
+#define AP1302_AE_CTRL_IMM1				BIT(4)
+#define AP1302_AE_CTRL_MANUAL_EXP_TIME_GAIN	(0U << 0)
+#define AP1302_AE_CTRL_MANUAL_BV_EXP_TIME	(1U << 0)
+#define AP1302_AE_CTRL_MANUAL_BV_GAIN		(2U << 0)
+#define AP1302_AE_CTRL_MANUAL_BV_ISO		(3U << 0)
+#define AP1302_AE_CTRL_AUTO_BV_EXP_TIME		(9U << 0)
+#define AP1302_AE_CTRL_AUTO_BV_GAIN			(10U << 0)
+#define AP1302_AE_CTRL_AUTO_BV_ISO			(11U << 0)
+#define AP1302_AE_CTRL_FULL_AUTO			(12U << 0)
+#define AP1302_AE_CTRL_MODE_MASK		0x000f
+#define AP1302_AE_MANUAL_GAIN		AP1302_REG_16BIT(0x5006)
+#define AP1302_AE_BV_OFF			AP1302_REG_16BIT(0x5014)
+#define AP1302_AE_MET				AP1302_REG_16BIT(0x503E)
+#define AP1302_AWB_CTRL				AP1302_REG_16BIT(0x5100)
+#define AP1302_AWB_CTRL_RECALC			BIT(13)
+#define AP1302_AWB_CTRL_POSTGAIN		BIT(12)
+#define AP1302_AWB_CTRL_UNGAIN			BIT(11)
+#define AP1302_AWB_CTRL_CLIP			BIT(10)
+#define AP1302_AWB_CTRL_SKY			BIT(9)
+#define AP1302_AWB_CTRL_FLASH			BIT(8)
+#define AP1302_AWB_CTRL_FACE_OFF		(0U << 6)
+#define AP1302_AWB_CTRL_FACE_IGNORE		(1U << 6)
+#define AP1302_AWB_CTRL_FACE_CONSTRAINED	(2U << 6)
+#define AP1302_AWB_CTRL_FACE_ONLY		(3U << 6)
+#define AP1302_AWB_CTRL_IMM			BIT(5)
+#define AP1302_AWB_CTRL_IMM1			BIT(4)
+#define AP1302_AWB_CTRL_MODE_OFF		(0U << 0)
+#define AP1302_AWB_CTRL_MODE_HORIZON		(1U << 0)
+#define AP1302_AWB_CTRL_MODE_A			(2U << 0)
+#define AP1302_AWB_CTRL_MODE_CWF		(3U << 0)
+#define AP1302_AWB_CTRL_MODE_D50		(4U << 0)
+#define AP1302_AWB_CTRL_MODE_D65		(5U << 0)
+#define AP1302_AWB_CTRL_MODE_D75		(6U << 0)
+#define AP1302_AWB_CTRL_MODE_MANUAL		(7U << 0)
+#define AP1302_AWB_CTRL_MODE_MEASURE		(8U << 0)
+#define AP1302_AWB_CTRL_MODE_AUTO		(15U << 0)
+#define AP1302_AWB_CTRL_MODE_MASK		0x000f
+#define AP1302_FLICK_CTRL			AP1302_REG_16BIT(0x5440)
+#define AP1302_FLICK_CTRL_FREQ(n)		((n) << 8)
+#define AP1302_FLICK_CTRL_ETC_IHDR_UP		BIT(6)
+#define AP1302_FLICK_CTRL_ETC_DIS		BIT(5)
+#define AP1302_FLICK_CTRL_FRC_OVERRIDE_MAX_ET	BIT(4)
+#define AP1302_FLICK_CTRL_FRC_OVERRIDE_UPPER_ET	BIT(3)
+#define AP1302_FLICK_CTRL_FRC_EN		BIT(2)
+#define AP1302_FLICK_CTRL_MODE_DISABLED		(0U << 0)
+#define AP1302_FLICK_CTRL_MODE_MANUAL		(1U << 0)
+#define AP1302_FLICK_CTRL_MODE_AUTO		(2U << 0)
+#define AP1302_SCENE_CTRL			AP1302_REG_16BIT(0x5454)
+#define AP1302_SCENE_CTRL_MODE_NORMAL		(0U << 0)
+#define AP1302_SCENE_CTRL_MODE_PORTRAIT		(1U << 0)
+#define AP1302_SCENE_CTRL_MODE_LANDSCAPE	(2U << 0)
+#define AP1302_SCENE_CTRL_MODE_SPORT		(3U << 0)
+#define AP1302_SCENE_CTRL_MODE_CLOSE_UP		(4U << 0)
+#define AP1302_SCENE_CTRL_MODE_NIGHT		(5U << 0)
+#define AP1302_SCENE_CTRL_MODE_TWILIGHT		(6U << 0)
+#define AP1302_SCENE_CTRL_MODE_BACKLIGHT	(7U << 0)
+#define AP1302_SCENE_CTRL_MODE_HIGH_SENSITIVE	(8U << 0)
+#define AP1302_SCENE_CTRL_MODE_NIGHT_PORTRAIT	(9U << 0)
+#define AP1302_SCENE_CTRL_MODE_BEACH		(10U << 0)
+#define AP1302_SCENE_CTRL_MODE_DOCUMENT		(11U << 0)
+#define AP1302_SCENE_CTRL_MODE_PARTY		(12U << 0)
+#define AP1302_SCENE_CTRL_MODE_FIREWORKS	(13U << 0)
+#define AP1302_SCENE_CTRL_MODE_SUNSET		(14U << 0)
+#define AP1302_SCENE_CTRL_MODE_AUTO		(0xffU << 0)
+
+/* System Registers */
+#define AP1302_BOOTDATA_STAGE			AP1302_REG_16BIT(0x6002)
+#define AP1302_WARNING(n)			AP1302_REG_16BIT(0x6004 + (n) * 2)
+#define AP1302_SENSOR_SELECT			AP1302_REG_16BIT(0x600c)
+#define AP1302_SENSOR_SELECT_TP_MODE(n)		((n) << 8)
+#define AP1302_SENSOR_SELECT_TP_MODE_MASK	0x0f00
+#define AP1302_SENSOR_SELECT_PATTERN_ON		BIT(7)
+#define AP1302_SENSOR_SELECT_MODE_3D_ON		BIT(6)
+#define AP1302_SENSOR_SELECT_CLOCK		BIT(5)
+#define AP1302_SENSOR_SELECT_SINF_MIPI		BIT(4)
+#define AP1302_SENSOR_SELECT_YUV		BIT(2)
+#define AP1302_SENSOR_SELECT_SENSOR_TP		(0U << 0)
+#define AP1302_SENSOR_SELECT_SENSOR(n)		(((n) + 1) << 0)
+#define AP1302_SENSOR_SELECT_SENSOR_MASK	0x0003
+#define AP1302_SYS_START			AP1302_REG_16BIT(0x601a)
+#define AP1302_SYS_START_PLL_LOCK		BIT(15)
+#define AP1302_SYS_START_LOAD_OTP		BIT(12)
+#define AP1302_SYS_START_RESTART_ERROR		BIT(11)
+#define AP1302_SYS_START_STALL_STATUS		BIT(9)
+#define AP1302_SYS_START_STALL_EN		BIT(8)
+#define AP1302_SYS_START_STALL_MODE_FRAME	(0U << 6)
+#define AP1302_SYS_START_STALL_MODE_DISABLED	(1U << 6)
+#define AP1302_SYS_START_STALL_MODE_POWER_DOWN	(2U << 6)
+#define AP1302_SYS_START_GO			BIT(4)
+#define AP1302_SYS_START_PATCH_FUN		BIT(1)
+#define AP1302_SYS_START_PLL_INIT		BIT(0)
+#define AP1302_DMA_SRC				AP1302_REG_32BIT(0x60a0)
+#define AP1302_DMA_DST				AP1302_REG_32BIT(0x60a4)
+#define AP1302_DMA_SIP_SIPM(n)			((n) << 26)
+#define AP1302_DMA_SIP_DATA_16_BIT		BIT(25)
+#define AP1302_DMA_SIP_ADDR_16_BIT		BIT(24)
+#define AP1302_DMA_SIP_ID(n)			((n) << 17)
+#define AP1302_DMA_SIP_REG(n)			((n) << 0)
+#define AP1302_DMA_SIZE				AP1302_REG_32BIT(0x60a8)
+#define AP1302_DMA_CTRL				AP1302_REG_16BIT(0x60ac)
+#define AP1302_DMA_CTRL_SCH_NORMAL		(0 << 12)
+#define AP1302_DMA_CTRL_SCH_NEXT		(1 << 12)
+#define AP1302_DMA_CTRL_SCH_NOW			(2 << 12)
+#define AP1302_DMA_CTRL_DST_REG			(0 << 8)
+#define AP1302_DMA_CTRL_DST_SRAM		(1 << 8)
+#define AP1302_DMA_CTRL_DST_SPI			(2 << 8)
+#define AP1302_DMA_CTRL_DST_SIP			(3 << 8)
+#define AP1302_DMA_CTRL_SRC_REG			(0 << 4)
+#define AP1302_DMA_CTRL_SRC_SRAM		(1 << 4)
+#define AP1302_DMA_CTRL_SRC_SPI			(2 << 4)
+#define AP1302_DMA_CTRL_SRC_SIP			(3 << 4)
+#define AP1302_DMA_CTRL_MODE_32_BIT		BIT(3)
+#define AP1302_DMA_CTRL_MODE_MASK		(7 << 0)
+#define AP1302_DMA_CTRL_MODE_IDLE		(0 << 0)
+#define AP1302_DMA_CTRL_MODE_SET		(1 << 0)
+#define AP1302_DMA_CTRL_MODE_COPY		(2 << 0)
+#define AP1302_DMA_CTRL_MODE_MAP		(3 << 0)
+#define AP1302_DMA_CTRL_MODE_UNPACK		(4 << 0)
+#define AP1302_DMA_CTRL_MODE_OTP_READ		(5 << 0)
+#define AP1302_DMA_CTRL_MODE_SIP_PROBE		(6 << 0)
+
+#define AP1302_BRIGHTNESS			AP1302_REG_16BIT(0x7000)
+#define AP1302_CONTRAST			AP1302_REG_16BIT(0x7002)
+#define AP1302_SATURATION			AP1302_REG_16BIT(0x7006)
+#define AP1302_GAMMA				AP1302_REG_16BIT(0x700A)
+
+/* Misc Registers */
+#define AP1302_REG_ADV_START			0xe000
+#define AP1302_ADVANCED_BASE			AP1302_REG_32BIT(0xf038)
+#define AP1302_SIP_CRC				AP1302_REG_16BIT(0xf052)
+
+/* Advanced System Registers */
+#define AP1302_ADV_IRQ_SYS_INTE			AP1302_REG_32BIT(0x00230000)
+#define AP1302_ADV_IRQ_SYS_INTE_TEST_COUNT	BIT(25)
+#define AP1302_ADV_IRQ_SYS_INTE_HINF_1		BIT(24)
+#define AP1302_ADV_IRQ_SYS_INTE_HINF_0		BIT(23)
+#define AP1302_ADV_IRQ_SYS_INTE_SINF_B_MIPI_L	(7U << 20)
+#define AP1302_ADV_IRQ_SYS_INTE_SINF_B_MIPI	BIT(19)
+#define AP1302_ADV_IRQ_SYS_INTE_SINF_A_MIPI_L	(15U << 14)
+#define AP1302_ADV_IRQ_SYS_INTE_SINF_A_MIPI	BIT(13)
+#define AP1302_ADV_IRQ_SYS_INTE_SINF		BIT(12)
+#define AP1302_ADV_IRQ_SYS_INTE_IPIPE_S		BIT(11)
+#define AP1302_ADV_IRQ_SYS_INTE_IPIPE_B		BIT(10)
+#define AP1302_ADV_IRQ_SYS_INTE_IPIPE_A		BIT(9)
+#define AP1302_ADV_IRQ_SYS_INTE_IP		BIT(8)
+#define AP1302_ADV_IRQ_SYS_INTE_TIMER		BIT(7)
+#define AP1302_ADV_IRQ_SYS_INTE_SIPM		(3U << 6)
+#define AP1302_ADV_IRQ_SYS_INTE_SIPS_ADR_RANGE	BIT(5)
+#define AP1302_ADV_IRQ_SYS_INTE_SIPS_DIRECT_WRITE	BIT(4)
+#define AP1302_ADV_IRQ_SYS_INTE_SIPS_FIFO_WRITE	BIT(3)
+#define AP1302_ADV_IRQ_SYS_INTE_SPI		BIT(2)
+#define AP1302_ADV_IRQ_SYS_INTE_GPIO_CNT	BIT(1)
+#define AP1302_ADV_IRQ_SYS_INTE_GPIO_PIN	BIT(0)
+
+/* Advanced Slave MIPI Registers */
+#define AP1302_ADV_SINF_MIPI_INTERNAL_p_LANE_n_STAT(p, n) \
+	AP1302_REG_32BIT(0x00420008 + (p) * 0x50000 + (n) * 0x20)
+#define AP1302_LANE_ERR_LP_VAL(n)		(((n) >> 30) & 3)
+#define AP1302_LANE_ERR_STATE(n)		(((n) >> 24) & 0xf)
+#define AP1302_LANE_ERR				BIT(18)
+#define AP1302_LANE_ABORT			BIT(17)
+#define AP1302_LANE_LP_VAL(n)			(((n) >> 6) & 3)
+#define AP1302_LANE_STATE(n)			((n) & 0xf)
+#define AP1302_LANE_STATE_STOP_S		0x0
+#define AP1302_LANE_STATE_HS_REQ_S		0x1
+#define AP1302_LANE_STATE_LP_REQ_S		0x2
+#define AP1302_LANE_STATE_HS_S			0x3
+#define AP1302_LANE_STATE_LP_S			0x4
+#define AP1302_LANE_STATE_ESC_REQ_S		0x5
+#define AP1302_LANE_STATE_TURN_REQ_S		0x6
+#define AP1302_LANE_STATE_ESC_S			0x7
+#define AP1302_LANE_STATE_ESC_0			0x8
+#define AP1302_LANE_STATE_ESC_1			0x9
+#define AP1302_LANE_STATE_TURN_S		0xa
+#define AP1302_LANE_STATE_TURN_MARK		0xb
+#define AP1302_LANE_STATE_ERROR_S		0xc
+
+#define AP1302_ADV_CAPTURE_A_FV_CNT		AP1302_REG_32BIT(0x00490040)
+#define AP1302_ADV_HINF_MIPI_T3		AP1302_REG_32BIT(0x840014)
+#define AP1302_TCLK_POST_MASK			0xFF
+#define AP1302_TCLK_POST_SHIFT			0x0
+#define AP1302_TCLK_PRE_MASK			0xFF00
+#define AP1302_TCLK_PRE_SHIFT			0x8
+
+struct ap1302_device;
+
+enum {
+	AP1302_PAD_SINK_0,
+	AP1302_PAD_SINK_1,
+	AP1302_PAD_SOURCE,
+	AP1302_PAD_MAX,
+};
+
+struct ap1302_format_info {
+	unsigned int code;
+	u16 out_fmt;
+};
+
+struct ap1302_format {
+	struct v4l2_mbus_framefmt format;
+	const struct ap1302_format_info *info;
+};
+
+struct ap1302_size {
+	unsigned int width;
+	unsigned int height;
+};
+
+struct ap1302_sensor_supply {
+	const char *name;
+	unsigned int post_delay_us;
+};
+
+struct ap1302_sensor_info {
+	const char *model;
+	const char *name;
+	unsigned int i2c_addr;
+	struct ap1302_size resolution;
+	u32 format;
+	const struct ap1302_sensor_supply *supplies;
+};
+
+struct ap1302_sensor {
+	struct ap1302_device *ap1302;
+	unsigned int index;
+
+	struct device_node *of_node;
+	struct device *dev;
+	unsigned int num_supplies;
+	struct regulator_bulk_data *supplies;
+
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+};
+
+static inline struct ap1302_sensor *to_ap1302_sensor(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct ap1302_sensor, sd);
+}
+
+struct ap1302_device {
+	struct device *dev;
+	struct i2c_client *client;
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *standby_gpio;
+	struct clk *clock;
+	struct regmap *regmap16;
+	struct regmap *regmap32;
+	u32 reg_page;
+
+	const struct firmware *fw;
+
+	struct v4l2_fwnode_endpoint bus_cfg;
+
+	struct mutex lock;	/* Protects formats */
+
+	struct v4l2_subdev sd;
+	struct media_pad pads[AP1302_PAD_MAX];
+	struct ap1302_format formats[AP1302_PAD_MAX];
+	unsigned int width_factor;
+	bool streaming;
+
+	struct v4l2_ctrl_handler ctrls;
+
+	const struct ap1302_sensor_info *sensor_info;
+	struct ap1302_sensor sensors[2];
+
+	struct {
+		struct dentry *dir;
+		struct mutex lock;
+		u32 sipm_addr;
+	} debugfs;
+};
+
+static inline struct ap1302_device *to_ap1302(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct ap1302_device, sd);
+}
+
+struct ap1302_firmware_header {
+	u16 pll_init_size;
+	u16 crc;
+} __packed;
+
+#define MAX_FW_LOAD_RETRIES 3
+
+static const struct ap1302_format_info supported_video_formats[] = {
+	{
+		.code = MEDIA_BUS_FMT_UYVY8_1X16,
+		.out_fmt = AP1302_PREVIEW_OUT_FMT_FT_YUV_JFIF
+			 | AP1302_PREVIEW_OUT_FMT_FST_YUV_422,
+	}, {
+		.code = MEDIA_BUS_FMT_UYYVYY8_0_5X24,
+		.out_fmt = AP1302_PREVIEW_OUT_FMT_FT_YUV_JFIF
+			 | AP1302_PREVIEW_OUT_FMT_FST_YUV_420,
+	}, {
+		.code = MEDIA_BUS_FMT_VYYUYY8_1X24,
+		.out_fmt = AP1302_PREVIEW_OUT_FMT_FT_YUV_JFIF
+			 | AP1302_PREVIEW_OUT_FMT_FST_YUV_420,
+	},
+};
+
+/* -----------------------------------------------------------------------------
+ * Sensor Info
+ */
+
+static const struct ap1302_sensor_info ap1302_sensor_info[] = {
+	{
+		.model = "onnn,ar0144",
+		.name = "ar0144",
+		.i2c_addr = 0x10,
+		.resolution = { 1280, 800 },
+		.format = MEDIA_BUS_FMT_SGRBG12_1X12,
+		.supplies = (const struct ap1302_sensor_supply[]) {
+			{ "vaa", 0 },
+			{ "vddio", 0 },
+			{ "vdd", 0 },
+			{ NULL, 0 },
+		},
+	}, {
+		.model = "onnn,ar0330",
+		.name = "ar0330",
+		.i2c_addr = 0x10,
+		.resolution = { 2304, 1536 },
+		.format = MEDIA_BUS_FMT_SGRBG12_1X12,
+		.supplies = (const struct ap1302_sensor_supply[]) {
+			{ "vddpll", 0 },
+			{ "vaa", 0 },
+			{ "vdd", 0 },
+			{ "vddio", 0 },
+			{ NULL, 0 },
+		},
+	}, {
+		.model = "onnn,ar1335",
+		.name = "ar1335",
+		.i2c_addr = 0x36,
+		.resolution = { 4208, 3120 },
+		.format = MEDIA_BUS_FMT_SGRBG10_1X10,
+		.supplies = (const struct ap1302_sensor_supply[]) {
+			{ "vaa", 0 },
+			{ "vddio", 0 },
+			{ "vdd", 0 },
+			{ NULL, 0 },
+		},
+	},
+};
+
+static const struct ap1302_sensor_info ap1302_sensor_info_tpg = {
+	.model = "",
+	.name = "tpg",
+	.resolution = { 1920, 1080 },
+};
+
+/* -----------------------------------------------------------------------------
+ * Register Configuration
+ */
+
+static const struct regmap_config ap1302_reg16_config = {
+	.reg_bits = 16,
+	.val_bits = 16,
+	.reg_stride = 2,
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_BIG,
+	.cache_type = REGCACHE_NONE,
+};
+
+static const struct regmap_config ap1302_reg32_config = {
+	.reg_bits = 16,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_BIG,
+	.cache_type = REGCACHE_NONE,
+};
+
+static int __ap1302_write(struct ap1302_device *ap1302, u32 reg, u32 val)
+{
+	unsigned int size = AP1302_REG_SIZE(reg);
+	u16 addr = AP1302_REG_ADDR(reg);
+	int ret;
+
+	switch (size) {
+	case 2:
+		ret = regmap_write(ap1302->regmap16, addr, val);
+		break;
+	case 4:
+		ret = regmap_write(ap1302->regmap32, addr, val);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (ret) {
+		dev_err(ap1302->dev, "%s: register 0x%04x %s failed: %d\n",
+			__func__, addr, "write", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ap1302_write(struct ap1302_device *ap1302, u32 reg, u32 val,
+			int *err)
+{
+	u32 page = AP1302_REG_PAGE(reg);
+	int ret;
+
+	if (err && *err)
+		return *err;
+
+	if (page) {
+		if (ap1302->reg_page != page) {
+			ret = __ap1302_write(ap1302, AP1302_ADVANCED_BASE,
+					     page);
+			if (ret < 0)
+				goto done;
+
+			ap1302->reg_page = page;
+		}
+
+		reg &= ~AP1302_REG_PAGE_MASK;
+		reg += AP1302_REG_ADV_START;
+	}
+
+	ret = __ap1302_write(ap1302, reg, val);
+
+done:
+	if (err && ret)
+		*err = ret;
+
+	return ret;
+}
+
+static int __ap1302_read(struct ap1302_device *ap1302, u32 reg, u32 *val)
+{
+	unsigned int size = AP1302_REG_SIZE(reg);
+	u16 addr = AP1302_REG_ADDR(reg);
+	int ret;
+
+	switch (size) {
+	case 2:
+		ret = regmap_read(ap1302->regmap16, addr, val);
+		break;
+	case 4:
+		ret = regmap_read(ap1302->regmap32, addr, val);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (ret) {
+		dev_err(ap1302->dev, "%s: register 0x%04x %s failed: %d\n",
+			__func__, addr, "read", ret);
+		return ret;
+	}
+
+	dev_dbg(ap1302->dev, "%s: R0x%04x = 0x%0*x\n", __func__,
+		addr, size * 2, *val);
+
+	return 0;
+}
+
+static int ap1302_read(struct ap1302_device *ap1302, u32 reg, u32 *val)
+{
+	u32 page = AP1302_REG_PAGE(reg);
+	int ret;
+
+	if (page) {
+		if (ap1302->reg_page != page) {
+			ret = __ap1302_write(ap1302, AP1302_ADVANCED_BASE,
+					     page);
+			if (ret < 0)
+				return ret;
+
+			ap1302->reg_page = page;
+		}
+
+		reg &= ~AP1302_REG_PAGE_MASK;
+		reg += AP1302_REG_ADV_START;
+	}
+
+	return __ap1302_read(ap1302, reg, val);
+}
+
+/* -----------------------------------------------------------------------------
+ * Sensor Registers Access
+ *
+ * Read and write sensor registers through the AP1302 DMA interface.
+ */
+
+static int ap1302_dma_wait_idle(struct ap1302_device *ap1302)
+{
+	unsigned int i;
+	u32 ctrl;
+	int ret;
+
+	for (i = 50; i > 0; i--) {
+		ret = ap1302_read(ap1302, AP1302_DMA_CTRL, &ctrl);
+		if (ret < 0)
+			return ret;
+
+		if ((ctrl & AP1302_DMA_CTRL_MODE_MASK) ==
+		    AP1302_DMA_CTRL_MODE_IDLE)
+			break;
+
+		usleep_range(1000, 1500);
+	}
+
+	if (!i) {
+		dev_err(ap1302->dev, "DMA timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int ap1302_sipm_read(struct ap1302_device *ap1302, unsigned int port,
+			    u32 reg, u32 *val)
+{
+	unsigned int size = AP1302_REG_SIZE(reg);
+	u32 src;
+	int ret;
+
+	if (size > 2)
+		return -EINVAL;
+
+	ret = ap1302_dma_wait_idle(ap1302);
+	if (ret < 0)
+		return ret;
+
+	ap1302_write(ap1302, AP1302_DMA_SIZE, size, &ret);
+	src = AP1302_DMA_SIP_SIPM(port)
+	    | (size == 2 ? AP1302_DMA_SIP_DATA_16_BIT : 0)
+	    | AP1302_DMA_SIP_ADDR_16_BIT
+	    | AP1302_DMA_SIP_ID(ap1302->sensor_info->i2c_addr)
+	    | AP1302_DMA_SIP_REG(AP1302_REG_ADDR(reg));
+	ap1302_write(ap1302, AP1302_DMA_SRC, src, &ret);
+
+	/*
+	 * Use the AP1302_DMA_DST register as both the destination address, and
+	 * the scratch pad to store the read value.
+	 */
+	ap1302_write(ap1302, AP1302_DMA_DST, AP1302_REG_ADDR(AP1302_DMA_DST),
+		     &ret);
+
+	ap1302_write(ap1302, AP1302_DMA_CTRL,
+		     AP1302_DMA_CTRL_SCH_NORMAL |
+		     AP1302_DMA_CTRL_DST_REG |
+		     AP1302_DMA_CTRL_SRC_SIP |
+		     AP1302_DMA_CTRL_MODE_COPY, &ret);
+	if (ret < 0)
+		return ret;
+
+	ret = ap1302_dma_wait_idle(ap1302);
+	if (ret < 0)
+		return ret;
+
+	ret = ap1302_read(ap1302, AP1302_DMA_DST, val);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * The value is stored in big-endian at the DMA_DST address. The regmap
+	 * uses big-endian, so 8-bit values are stored in bits 31:24 and 16-bit
+	 * values in bits 23:16.
+	 */
+	*val >>= 32 - size * 8;
+
+	return 0;
+}
+
+static int ap1302_sipm_write(struct ap1302_device *ap1302, unsigned int port,
+			     u32 reg, u32 val)
+{
+	unsigned int size = AP1302_REG_SIZE(reg);
+	u32 dst;
+	int ret;
+
+	if (size > 2)
+		return -EINVAL;
+
+	ret = ap1302_dma_wait_idle(ap1302);
+	if (ret < 0)
+		return ret;
+
+	ap1302_write(ap1302, AP1302_DMA_SIZE, size, &ret);
+
+	/*
+	 * Use the AP1302_DMA_SRC register as both the source address, and the
+	 * scratch pad to store the write value.
+	 *
+	 * As the AP1302 uses big endian, to store the value at address DMA_SRC
+	 * it must be written in the high order bits of the registers. However,
+	 * 8-bit values seem to be incorrectly handled by the AP1302, which
+	 * expects them to be stored at DMA_SRC + 1 instead of DMA_SRC. The
+	 * value is thus unconditionally shifted by 16 bits, unlike for DMA
+	 * reads.
+	 */
+	ap1302_write(ap1302, AP1302_DMA_SRC,
+		     (val << 16) | AP1302_REG_ADDR(AP1302_DMA_SRC), &ret);
+	if (ret < 0)
+		return ret;
+
+	dst = AP1302_DMA_SIP_SIPM(port)
+	    | (size == 2 ? AP1302_DMA_SIP_DATA_16_BIT : 0)
+	    | AP1302_DMA_SIP_ADDR_16_BIT
+	    | AP1302_DMA_SIP_ID(ap1302->sensor_info->i2c_addr)
+	    | AP1302_DMA_SIP_REG(AP1302_REG_ADDR(reg));
+	ap1302_write(ap1302, AP1302_DMA_DST, dst, &ret);
+
+	ap1302_write(ap1302, AP1302_DMA_CTRL,
+		     AP1302_DMA_CTRL_SCH_NORMAL |
+		     AP1302_DMA_CTRL_DST_SIP |
+		     AP1302_DMA_CTRL_SRC_REG |
+		     AP1302_DMA_CTRL_MODE_COPY, &ret);
+	if (ret < 0)
+		return ret;
+
+	ret = ap1302_dma_wait_idle(ap1302);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Debugfs
+ */
+
+static int ap1302_sipm_addr_get(void *arg, u64 *val)
+{
+	struct ap1302_device *ap1302 = arg;
+
+	mutex_lock(&ap1302->debugfs.lock);
+	*val = ap1302->debugfs.sipm_addr;
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return 0;
+}
+
+static int ap1302_sipm_addr_set(void *arg, u64 val)
+{
+	struct ap1302_device *ap1302 = arg;
+
+	if (val & ~0x8700ffff)
+		return -EINVAL;
+
+	switch ((val >> 24) & 7) {
+	case 1:
+	case 2:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	mutex_lock(&ap1302->debugfs.lock);
+	ap1302->debugfs.sipm_addr = val;
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return 0;
+}
+
+static int ap1302_sipm_data_get(void *arg, u64 *val)
+{
+	struct ap1302_device *ap1302 = arg;
+	u32 value;
+	u32 addr;
+	int ret;
+
+	mutex_lock(&ap1302->debugfs.lock);
+
+	addr = ap1302->debugfs.sipm_addr;
+	if (!addr) {
+		ret = -EINVAL;
+		goto unlock;
+	}
+
+	ret = ap1302_sipm_read(ap1302, addr >> 30, addr & ~BIT(31),
+			       &value);
+	if (!ret)
+		*val = value;
+
+unlock:
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return ret;
+}
+
+static int ap1302_sipm_data_set(void *arg, u64 val)
+{
+	struct ap1302_device *ap1302 = arg;
+	u32 addr;
+	int ret;
+
+	mutex_lock(&ap1302->debugfs.lock);
+
+	addr = ap1302->debugfs.sipm_addr;
+	if (!addr) {
+		ret = -EINVAL;
+		goto unlock;
+	}
+
+	ret = ap1302_sipm_write(ap1302, addr >> 30, addr & ~BIT(31),
+				val);
+
+unlock:
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return ret;
+}
+
+static int ap1302_mipi_tclk_post_get(void *arg, u64 *val)
+{
+	struct ap1302_device *ap1302 = arg;
+	u32 value;
+	int ret;
+
+	mutex_lock(&ap1302->debugfs.lock);
+
+	ret = ap1302_read(ap1302, AP1302_ADV_HINF_MIPI_T3, &value);
+	if (!ret)
+		*val = value & AP1302_TCLK_POST_MASK;
+
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return ret;
+}
+
+static int ap1302_mipi_tclk_post_set(void *arg, u64 val)
+{
+	struct ap1302_device *ap1302 = arg;
+	u32 reg, reg_val;
+	int ret;
+
+	mutex_lock(&ap1302->debugfs.lock);
+	ret = ap1302_read(ap1302, AP1302_ADV_HINF_MIPI_T3, &reg);
+	if (ret < 0)
+		goto unlock;
+
+	reg_val = reg & ~(AP1302_TCLK_POST_MASK);
+	reg_val = reg_val | val;
+	ret = ap1302_write(ap1302, AP1302_ADV_HINF_MIPI_T3, reg_val, NULL);
+
+unlock:
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return ret;
+}
+
+static int ap1302_mipi_tclk_pre_get(void *arg, u64 *val)
+{
+	struct ap1302_device *ap1302 = arg;
+	u32 value;
+	int ret;
+
+	mutex_lock(&ap1302->debugfs.lock);
+
+	ret = ap1302_read(ap1302, AP1302_ADV_HINF_MIPI_T3, &value);
+	if (!ret)
+		*val = (value & AP1302_TCLK_PRE_MASK) >> AP1302_TCLK_PRE_SHIFT;
+
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return ret;
+}
+
+static int ap1302_mipi_tclk_pre_set(void *arg, u64 val)
+{
+	struct ap1302_device *ap1302 = arg;
+	u32 reg, reg_val;
+	int ret;
+
+	mutex_lock(&ap1302->debugfs.lock);
+	ret = ap1302_read(ap1302, AP1302_ADV_HINF_MIPI_T3, &reg);
+	if (ret < 0)
+		goto unlock;
+
+	reg_val = reg & ~(AP1302_TCLK_PRE_MASK);
+	reg_val = reg_val | val << AP1302_TCLK_PRE_SHIFT;
+	ret = ap1302_write(ap1302, AP1302_ADV_HINF_MIPI_T3, reg_val, NULL);
+
+unlock:
+	mutex_unlock(&ap1302->debugfs.lock);
+
+	return ret;
+}
+
+/*
+ * The sipm_addr and sipm_data attributes expose access to the sensor I2C bus.
+ *
+ * To read or write a register, sipm_addr has to first be written with the
+ * register address. The address is a 32-bit integer formatted as follows.
+ *
+ * I000 0SSS 0000 0000 RRRR RRRR RRRR RRRR
+ *
+ * I: SIPM index (0 or 1)
+ * S: Size (1: 8-bit, 2: 16-bit)
+ * R: Register address (16-bit)
+ *
+ * The sipm_data attribute can then be read to read the register value, or
+ * written to write it.
+ */
+
+DEFINE_DEBUGFS_ATTRIBUTE(ap1302_sipm_addr_fops, ap1302_sipm_addr_get,
+			 ap1302_sipm_addr_set, "0x%08llx\n");
+DEFINE_DEBUGFS_ATTRIBUTE(ap1302_sipm_data_fops, ap1302_sipm_data_get,
+			 ap1302_sipm_data_set, "0x%08llx\n");
+
+/* The debugfs is to read and write mipi clk parameters tclk_post values */
+DEFINE_DEBUGFS_ATTRIBUTE(ap1302_mipi_tclk_post_fops, ap1302_mipi_tclk_post_get,
+			 ap1302_mipi_tclk_post_set, "0x%08llx\n");
+
+/* The debugfs is to read and write mipi clk parameters and tclk_pre values */
+DEFINE_DEBUGFS_ATTRIBUTE(ap1302_mipi_tclk_pre_fops, ap1302_mipi_tclk_pre_get,
+			 ap1302_mipi_tclk_pre_set, "0x%08llx\n");
+
+static void ap1302_debugfs_init(struct ap1302_device *ap1302)
+{
+	struct dentry *dir;
+	char name[16];
+
+	mutex_init(&ap1302->debugfs.lock);
+
+	snprintf(name, sizeof(name), "ap1302.%s", dev_name(ap1302->dev));
+
+	dir = debugfs_create_dir(name, NULL);
+	if (IS_ERR(dir))
+		return;
+
+	ap1302->debugfs.dir = dir;
+
+	debugfs_create_file_unsafe("sipm_addr", 0600, ap1302->debugfs.dir,
+				   ap1302, &ap1302_sipm_addr_fops);
+	debugfs_create_file_unsafe("sipm_data", 0600, ap1302->debugfs.dir,
+				   ap1302, &ap1302_sipm_data_fops);
+	debugfs_create_file_unsafe("mipi_tclk_post", 0600, ap1302->debugfs.dir,
+				   ap1302, &ap1302_mipi_tclk_post_fops);
+	debugfs_create_file_unsafe("mipi_tclk_pre", 0600, ap1302->debugfs.dir,
+				   ap1302, &ap1302_mipi_tclk_pre_fops);
+}
+
+static void ap1302_debugfs_cleanup(struct ap1302_device *ap1302)
+{
+	debugfs_remove_recursive(ap1302->debugfs.dir);
+	mutex_destroy(&ap1302->debugfs.lock);
+}
+
+/* -----------------------------------------------------------------------------
+ * Power Handling
+ */
+
+static int ap1302_power_on_sensors(struct ap1302_device *ap1302)
+{
+	struct ap1302_sensor *sensor;
+	unsigned int i, j;
+	int ret;
+
+	if (!ap1302->sensor_info->supplies)
+		return 0;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		sensor = &ap1302->sensors[i];
+		ret = 0;
+
+		for (j = 0; j < sensor->num_supplies; ++j) {
+			unsigned int delay;
+
+			/*
+			 * We can't use regulator_bulk_enable() as it would
+			 * enable all supplies in parallel, breaking the sensor
+			 * power sequencing constraints.
+			 */
+			ret = regulator_enable(sensor->supplies[j].consumer);
+			if (ret < 0) {
+				dev_err(ap1302->dev,
+					"Failed to enable supply %u for sensor %u\n",
+					j, i);
+				goto error;
+			}
+
+			delay = ap1302->sensor_info->supplies[j].post_delay_us;
+			usleep_range(delay, delay + 100);
+		}
+	}
+
+	return 0;
+
+error:
+	for (; j > 0; --j)
+		regulator_disable(sensor->supplies[j - 1].consumer);
+
+	for (; i > 0; --i) {
+		sensor = &ap1302->sensors[i - 1];
+		regulator_bulk_disable(sensor->num_supplies, sensor->supplies);
+	}
+
+	return ret;
+}
+
+static void ap1302_power_off_sensors(struct ap1302_device *ap1302)
+{
+	unsigned int i;
+
+	if (!ap1302->sensor_info->supplies)
+		return;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		struct ap1302_sensor *sensor = &ap1302->sensors[i];
+
+		regulator_bulk_disable(sensor->num_supplies, sensor->supplies);
+	}
+}
+
+static int ap1302_power_on(struct ap1302_device *ap1302)
+{
+	int ret;
+
+	/* 0. RESET was asserted when getting the GPIO. */
+
+	/* 1. Assert STANDBY. */
+	if (ap1302->standby_gpio) {
+		gpiod_set_value(ap1302->standby_gpio, 1);
+		usleep_range(200, 1000);
+	}
+
+	/* 2. Power up the regulators. To be implemented. */
+
+	/* 3. De-assert STANDBY. */
+	if (ap1302->standby_gpio) {
+		gpiod_set_value(ap1302->standby_gpio, 0);
+		usleep_range(200, 1000);
+	}
+
+	/* 4. Turn the clock on. */
+	ret = clk_prepare_enable(ap1302->clock);
+	if (ret < 0) {
+		dev_err(ap1302->dev, "Failed to enable clock: %d\n", ret);
+		return ret;
+	}
+
+	/* 5. De-assert RESET. */
+	gpiod_set_value(ap1302->reset_gpio, 0);
+
+	/*
+	 * 6. Wait for the AP1302 to initialize. The datasheet doesn't specify
+	 * how long this takes.
+	 */
+	usleep_range(10000, 11000);
+
+	return 0;
+}
+
+static void ap1302_power_off(struct ap1302_device *ap1302)
+{
+	/* 1. Assert RESET. */
+	gpiod_set_value(ap1302->reset_gpio, 1);
+
+	/* 2. Turn the clock off. */
+	clk_disable_unprepare(ap1302->clock);
+
+	/* 3. Assert STANDBY. */
+	if (ap1302->standby_gpio) {
+		gpiod_set_value(ap1302->standby_gpio, 1);
+		usleep_range(200, 1000);
+	}
+
+	/* 4. Power down the regulators. To be implemented. */
+
+	/* 5. De-assert STANDBY. */
+	if (ap1302->standby_gpio) {
+		usleep_range(200, 1000);
+		gpiod_set_value(ap1302->standby_gpio, 0);
+	}
+}
+
+/* -----------------------------------------------------------------------------
+ * Hardware Configuration
+ */
+
+static int ap1302_dump_console(struct ap1302_device *ap1302)
+{
+	u8 *buffer;
+	u8 *endp;
+	u8 *p;
+	int ret;
+
+	buffer = kmalloc(AP1302_CON_BUF_SIZE + 1, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
+
+	ret = regmap_raw_read(ap1302->regmap16, AP1302_CON_BUF(0), buffer,
+			      AP1302_CON_BUF_SIZE);
+	if (ret < 0) {
+		dev_err(ap1302->dev, "Failed to read console buffer: %d\n",
+			ret);
+		goto done;
+	}
+
+	print_hex_dump(KERN_INFO, "console ", DUMP_PREFIX_OFFSET, 16, 1, buffer,
+		       AP1302_CON_BUF_SIZE, true);
+
+	buffer[AP1302_CON_BUF_SIZE] = '\0';
+
+	for (p = buffer; p < buffer + AP1302_CON_BUF_SIZE && *p; p = endp + 1) {
+		endp = strchrnul(p, '\n');
+		*endp = '\0';
+
+		pr_info("console %s\n", p);
+	}
+
+	ret = 0;
+
+done:
+	kfree(buffer);
+	return ret;
+}
+
+static int ap1302_configure(struct ap1302_device *ap1302)
+{
+	const struct ap1302_format *format = &ap1302->formats[AP1302_PAD_SOURCE];
+	unsigned int data_lanes = ap1302->bus_cfg.bus.mipi_csi2.num_data_lanes;
+	int ret = 0;
+
+	ap1302_write(ap1302, AP1302_PREVIEW_HINF_CTRL,
+		     AP1302_PREVIEW_HINF_CTRL_SPOOF |
+		     AP1302_PREVIEW_HINF_CTRL_MIPI_LANES(data_lanes), &ret);
+
+	ap1302_write(ap1302, AP1302_PREVIEW_WIDTH,
+		     format->format.width / ap1302->width_factor, &ret);
+	ap1302_write(ap1302, AP1302_PREVIEW_HEIGHT,
+		     format->format.height, &ret);
+	ap1302_write(ap1302, AP1302_PREVIEW_OUT_FMT,
+		     format->info->out_fmt, &ret);
+	if (ret < 0)
+		return ret;
+
+	__v4l2_ctrl_handler_setup(&ap1302->ctrls);
+
+	return 0;
+}
+
+static int ap1302_stall(struct ap1302_device *ap1302, bool stall)
+{
+	int ret = 0;
+
+	if (stall) {
+		ap1302_write(ap1302, AP1302_SYS_START,
+			     AP1302_SYS_START_PLL_LOCK |
+			     AP1302_SYS_START_STALL_MODE_DISABLED, &ret);
+		ap1302_write(ap1302, AP1302_SYS_START,
+			     AP1302_SYS_START_PLL_LOCK |
+			     AP1302_SYS_START_STALL_EN |
+			     AP1302_SYS_START_STALL_MODE_DISABLED, &ret);
+		if (ret < 0)
+			return ret;
+
+		msleep(200);
+
+		ap1302_write(ap1302, AP1302_ADV_IRQ_SYS_INTE,
+			     AP1302_ADV_IRQ_SYS_INTE_SIPM |
+			     AP1302_ADV_IRQ_SYS_INTE_SIPS_FIFO_WRITE, &ret);
+		if (ret < 0)
+			return ret;
+
+		ap1302->streaming = false;
+		return 0;
+	} else {
+		ap1302->streaming = true;
+		return ap1302_write(ap1302, AP1302_SYS_START,
+				    AP1302_SYS_START_PLL_LOCK |
+				    AP1302_SYS_START_STALL_STATUS |
+				    AP1302_SYS_START_STALL_EN |
+				    AP1302_SYS_START_STALL_MODE_DISABLED, NULL);
+	}
+}
+
+static int ap1302_set_mipi_t3_clk(struct ap1302_device *ap1302)
+{
+	unsigned int mipi_t3, t_clk_post, t_clk_pre;
+	int ret;
+
+	/* Set the Tclk_post and Tclk_pre values */
+	ret = ap1302_read(ap1302, AP1302_ADV_HINF_MIPI_T3, &mipi_t3);
+	if (ret)
+		return ret;
+
+	/* Read Tclk post default setting and increment by 2 */
+	t_clk_post = ((mipi_t3 & AP1302_TCLK_POST_MASK)
+					>> AP1302_TCLK_POST_SHIFT) + 0x5;
+	/* Read Tclk pre default setting and increment by 1 */
+	t_clk_pre = ((mipi_t3 & AP1302_TCLK_PRE_MASK)
+					>> AP1302_TCLK_PRE_SHIFT) + 0x1;
+
+	mipi_t3 = ((mipi_t3 & ~(AP1302_TCLK_POST_MASK))
+					& ~(AP1302_TCLK_PRE_MASK));
+	mipi_t3 = (mipi_t3 | (t_clk_pre << AP1302_TCLK_PRE_SHIFT)
+					| t_clk_post);
+
+	/* Write MIPI_T3 register with updated Tclk_post and Tclk_pre values */
+	return ap1302_write(ap1302, AP1302_ADV_HINF_MIPI_T3, mipi_t3, NULL);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Controls
+ */
+
+static u16 ap1302_wb_values[] = {
+	AP1302_AWB_CTRL_MODE_OFF,	/* V4L2_WHITE_BALANCE_MANUAL */
+	AP1302_AWB_CTRL_MODE_AUTO,	/* V4L2_WHITE_BALANCE_AUTO */
+	AP1302_AWB_CTRL_MODE_A,		/* V4L2_WHITE_BALANCE_INCANDESCENT */
+	AP1302_AWB_CTRL_MODE_D50,	/* V4L2_WHITE_BALANCE_FLUORESCENT */
+	AP1302_AWB_CTRL_MODE_D65,	/* V4L2_WHITE_BALANCE_FLUORESCENT_H */
+	AP1302_AWB_CTRL_MODE_HORIZON,	/* V4L2_WHITE_BALANCE_HORIZON */
+	AP1302_AWB_CTRL_MODE_D65,	/* V4L2_WHITE_BALANCE_DAYLIGHT */
+	AP1302_AWB_CTRL_MODE_AUTO,	/* V4L2_WHITE_BALANCE_FLASH */
+	AP1302_AWB_CTRL_MODE_D75,	/* V4L2_WHITE_BALANCE_CLOUDY */
+	AP1302_AWB_CTRL_MODE_D75,	/* V4L2_WHITE_BALANCE_SHADE */
+};
+
+static int ap1302_set_wb_mode(struct ap1302_device *ap1302, s32 mode)
+{
+	u32 val;
+	int ret;
+
+	ret = ap1302_read(ap1302, AP1302_AWB_CTRL, &val);
+	if (ret)
+		return ret;
+
+	val &= ~AP1302_AWB_CTRL_MODE_MASK;
+	val |= ap1302_wb_values[mode];
+
+	if (mode == V4L2_WHITE_BALANCE_FLASH)
+		val |= AP1302_AWB_CTRL_FLASH;
+	else
+		val &= ~AP1302_AWB_CTRL_FLASH;
+
+	return ap1302_write(ap1302, AP1302_AWB_CTRL, val, NULL);
+}
+
+static int ap1302_set_exposure(struct ap1302_device *ap1302, s32 mode)
+{
+	u32 val;
+	int ret;
+
+	ret = ap1302_read(ap1302, AP1302_AE_CTRL, &val);
+	if (ret)
+		return ret;
+
+	val &= ~AP1302_AE_CTRL_MODE_MASK;
+	val |= mode;
+
+	return ap1302_write(ap1302, AP1302_AE_CTRL, val, NULL);
+}
+
+static int ap1302_set_exp_met(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_AE_MET, val, NULL);
+}
+
+static int ap1302_set_gain(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_AE_MANUAL_GAIN, val, NULL);
+}
+
+static int ap1302_set_contrast(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_CONTRAST, val, NULL);
+}
+
+static int ap1302_set_brightness(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_BRIGHTNESS, val, NULL);
+}
+
+static int ap1302_set_saturation(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_SATURATION, val, NULL);
+}
+
+static int ap1302_set_gamma(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_GAMMA, val, NULL);
+}
+
+static int ap1302_set_zoom(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_DZ_TGT_FCT, val, NULL);
+}
+
+static u16 ap1302_sfx_values[] = {
+	AP1302_SFX_MODE_SFX_NORMAL,	/* V4L2_COLORFX_NONE */
+	AP1302_SFX_MODE_SFX_BW,		/* V4L2_COLORFX_BW */
+	AP1302_SFX_MODE_SFX_SEPIA1,	/* V4L2_COLORFX_SEPIA */
+	AP1302_SFX_MODE_SFX_NEGATIVE,	/* V4L2_COLORFX_NEGATIVE */
+	AP1302_SFX_MODE_SFX_EMBOSS,	/* V4L2_COLORFX_EMBOSS */
+	AP1302_SFX_MODE_SFX_SKETCH,	/* V4L2_COLORFX_SKETCH */
+	AP1302_SFX_MODE_SFX_BLUISH,	/* V4L2_COLORFX_SKY_BLUE */
+	AP1302_SFX_MODE_SFX_GREENISH,	/* V4L2_COLORFX_GRASS_GREEN */
+	AP1302_SFX_MODE_SFX_REDISH,	/* V4L2_COLORFX_SKIN_WHITEN */
+	AP1302_SFX_MODE_SFX_NORMAL,	/* V4L2_COLORFX_VIVID */
+	AP1302_SFX_MODE_SFX_NORMAL,	/* V4L2_COLORFX_AQUA */
+	AP1302_SFX_MODE_SFX_NORMAL,	/* V4L2_COLORFX_ART_FREEZE */
+	AP1302_SFX_MODE_SFX_NORMAL,	/* V4L2_COLORFX_SILHOUETTE */
+	AP1302_SFX_MODE_SFX_SOLARIZE, /* V4L2_COLORFX_SOLARIZATION */
+	AP1302_SFX_MODE_SFX_ANTIQUE, /* V4L2_COLORFX_ANTIQUE */
+	AP1302_SFX_MODE_SFX_NORMAL,	/* V4L2_COLORFX_SET_CBCR */
+};
+
+static int ap1302_set_special_effect(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_SFX_MODE, ap1302_sfx_values[val],
+			    NULL);
+}
+
+static u16 ap1302_scene_mode_values[] = {
+	AP1302_SCENE_CTRL_MODE_NORMAL,		/* V4L2_SCENE_MODE_NONE */
+	AP1302_SCENE_CTRL_MODE_BACKLIGHT,	/* V4L2_SCENE_MODE_BACKLIGHT */
+	AP1302_SCENE_CTRL_MODE_BEACH,		/* V4L2_SCENE_MODE_BEACH_SNOW */
+	AP1302_SCENE_CTRL_MODE_TWILIGHT,	/* V4L2_SCENE_MODE_CANDLE_LIGHT */
+	AP1302_SCENE_CTRL_MODE_NORMAL,		/* V4L2_SCENE_MODE_DAWN_DUSK */
+	AP1302_SCENE_CTRL_MODE_NORMAL,		/* V4L2_SCENE_MODE_FALL_COLORS */
+	AP1302_SCENE_CTRL_MODE_FIREWORKS,	/* V4L2_SCENE_MODE_FIREWORKS */
+	AP1302_SCENE_CTRL_MODE_LANDSCAPE,	/* V4L2_SCENE_MODE_LANDSCAPE */
+	AP1302_SCENE_CTRL_MODE_NIGHT,		/* V4L2_SCENE_MODE_NIGHT */
+	AP1302_SCENE_CTRL_MODE_PARTY,		/* V4L2_SCENE_MODE_PARTY_INDOOR */
+	AP1302_SCENE_CTRL_MODE_PORTRAIT,	/* V4L2_SCENE_MODE_PORTRAIT */
+	AP1302_SCENE_CTRL_MODE_SPORT,		/* V4L2_SCENE_MODE_SPORTS */
+	AP1302_SCENE_CTRL_MODE_SUNSET,		/* V4L2_SCENE_MODE_SUNSET */
+	AP1302_SCENE_CTRL_MODE_DOCUMENT,	/* V4L2_SCENE_MODE_TEXT */
+};
+
+static int ap1302_set_scene_mode(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_SCENE_CTRL,
+			    ap1302_scene_mode_values[val], NULL);
+}
+
+static const u16 ap1302_flicker_values[] = {
+	AP1302_FLICK_CTRL_MODE_DISABLED,
+	AP1302_FLICK_CTRL_FREQ(50) | AP1302_FLICK_CTRL_MODE_MANUAL,
+	AP1302_FLICK_CTRL_FREQ(60) | AP1302_FLICK_CTRL_MODE_MANUAL,
+	AP1302_FLICK_CTRL_MODE_AUTO,
+};
+
+static int ap1302_set_flicker_freq(struct ap1302_device *ap1302, s32 val)
+{
+	return ap1302_write(ap1302, AP1302_FLICK_CTRL,
+			    ap1302_flicker_values[val], NULL);
+}
+
+enum {
+	AP1302_TP_MODE_DISABLED = 0,
+	AP1302_TP_MODE_FLAT_COLOR,
+	AP1302_TP_MODE_PSEUDO_RANDOM,
+	AP1302_TP_MODE_COLOR_BARS,
+	AP1302_TP_MODE_GREY_BARS,
+	AP1302_TP_MODE_PRBS1,
+	AP1302_TP_MODE_PRBS2,
+	AP1302_TP_MODE_PRBS3,
+	AP1302_TP_MODE_PRBS4,
+	AP1302_TP_MODE_V_STRIPES,
+	AP1302_TP_MODE_V_RAMP,
+	AP1302_TP_MODE_WALKING_ONES_10B,
+	AP1302_TP_MODE_WALKING_ONES_8B,
+	AP1302_TP_MODE_BW,
+};
+
+static const char * const tp_qmenu[] = {
+	"Disabled",
+	"Flat Color",
+	"Pseudo Random (Noise)",
+	"100% Color Bars",
+	"Fade to Grey Bars",
+	"PRBS1",
+	"PRBS2",
+	"PRBS3",
+	"PRBS4",
+	"Vertical Stripes",
+	"Vertical Ramp",
+	"Walking 1's (10bit)",
+	"Walking 1's (8bit)",
+	"Black and White",
+};
+
+static int ap1302_set_test_pattern(struct ap1302_device *ap1302, s32 pat)
+{
+	u32 val;
+	int ret;
+
+	ret = ap1302_read(ap1302, AP1302_SENSOR_SELECT, &val);
+	if (ret)
+		return ret;
+
+	if (pat == AP1302_TP_MODE_DISABLED) {
+		val &= ~AP1302_SENSOR_SELECT_SENSOR_MASK;
+		/* The sensor field in the sensor select register defaults to primary
+		   sensor (0x1). Therefore, when disabling test pattern mode, restore
+		   the value by setting it to te primary sensor */
+		val |= AP1302_SENSOR_SELECT_SENSOR(0);
+		val &= ~AP1302_SENSOR_SELECT_PATTERN_ON;
+		val &= ~AP1302_SENSOR_SELECT_TP_MODE_MASK;
+		val |= AP1302_SENSOR_SELECT_TP_MODE(pat);
+	} else if (pat >= AP1302_TP_MODE_FLAT_COLOR && pat <= AP1302_TP_MODE_BW) {
+		val &= ~AP1302_SENSOR_SELECT_SENSOR_MASK;
+		val |= AP1302_SENSOR_SELECT_SENSOR_TP;
+		val |= AP1302_SENSOR_SELECT_PATTERN_ON;
+		val &= ~AP1302_SENSOR_SELECT_TP_MODE_MASK;
+		val |= AP1302_SENSOR_SELECT_TP_MODE(pat);
+	} else {
+		return -EINVAL;
+	}
+
+	return ap1302_write(ap1302, AP1302_SENSOR_SELECT, val, NULL);
+}
+
+static int ap1302_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ap1302_device *ap1302 =
+		container_of(ctrl->handler, struct ap1302_device, ctrls);
+
+	switch (ctrl->id) {
+	case V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE:
+		return ap1302_set_wb_mode(ap1302, ctrl->val);
+
+	case V4L2_CID_EXPOSURE:
+		return ap1302_set_exposure(ap1302, ctrl->val);
+
+	case V4L2_CID_EXPOSURE_METERING:
+		return ap1302_set_exp_met(ap1302, ctrl->val);
+
+	case V4L2_CID_GAIN:
+		return ap1302_set_gain(ap1302, ctrl->val);
+
+	case V4L2_CID_GAMMA:
+		return ap1302_set_gamma(ap1302, ctrl->val);
+
+	case V4L2_CID_CONTRAST:
+		return ap1302_set_contrast(ap1302, ctrl->val);
+
+	case V4L2_CID_BRIGHTNESS:
+		return ap1302_set_brightness(ap1302, ctrl->val);
+
+	case V4L2_CID_SATURATION:
+		return ap1302_set_saturation(ap1302, ctrl->val);
+
+	case V4L2_CID_ZOOM_ABSOLUTE:
+		return ap1302_set_zoom(ap1302, ctrl->val);
+
+	case V4L2_CID_COLORFX:
+		return ap1302_set_special_effect(ap1302, ctrl->val);
+
+	case V4L2_CID_SCENE_MODE:
+		return ap1302_set_scene_mode(ap1302, ctrl->val);
+
+	case V4L2_CID_POWER_LINE_FREQUENCY:
+		return ap1302_set_flicker_freq(ap1302, ctrl->val);
+
+	case V4L2_CID_TEST_PATTERN:
+		return ap1302_set_test_pattern(ap1302, ctrl->val);
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct v4l2_ctrl_ops ap1302_ctrl_ops = {
+	.s_ctrl = ap1302_s_ctrl,
+};
+
+static const struct v4l2_ctrl_config ap1302_ctrls[] = {
+	{
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE,
+		.min = 0,
+		.max = 9,
+		.def = 1,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_GAMMA,
+		.name = "Gamma",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0xFFFF,
+		.step = 0x100,
+		.def = 0x1000,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_CONTRAST,
+		.name = "Contrast",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0xFFFF,
+		.step = 0x100,
+		.def = 0x100,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_BRIGHTNESS,
+		.name = "Brightness",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0xFFFF,
+		.step = 0x100,
+		.def = 0x100,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_SATURATION,
+		.name = "Saturation",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0xFFFF,
+		.step = 0x100,
+		.def = 0x1000,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_EXPOSURE,
+		.name = "Exposure",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0xC,
+		.step = 1,
+		.def = 0xC,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_EXPOSURE_METERING,
+		.name = "Exposure Metering",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0x3,
+		.step = 1,
+		.def = 0x1,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_GAIN,
+		.name = "Gain",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0x0,
+		.max = 0xFFFF,
+		.step = 0x100,
+		.def = 0x100,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_ZOOM_ABSOLUTE,
+		.min = 0x0,
+		.max = 0x1000,
+		.step = 1,
+		.def = 0x0100,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_COLORFX,
+		.min = 0,
+		.max = 15,
+		.def = 0,
+		.menu_skip_mask = BIT(15) | BIT(12) | BIT(11) | BIT(10) | BIT(9),
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_SCENE_MODE,
+		.min = 0,
+		.max = 13,
+		.def = 0,
+		.menu_skip_mask = BIT(5) | BIT(4),
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_POWER_LINE_FREQUENCY,
+		.min = 0,
+		.max = 3,
+		.def = 3,
+	}, {
+		.ops = &ap1302_ctrl_ops,
+		.id = V4L2_CID_TEST_PATTERN,
+		.min = 0,
+		.max = (ARRAY_SIZE(tp_qmenu) - 1),
+		.def = 0,
+		.qmenu = tp_qmenu,
+	},
+};
+
+static int ap1302_ctrls_init(struct ap1302_device *ap1302)
+{
+	unsigned int i;
+	int ret;
+
+	ret = v4l2_ctrl_handler_init(&ap1302->ctrls, ARRAY_SIZE(ap1302_ctrls));
+	if (ret)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302_ctrls); i++)
+		v4l2_ctrl_new_custom(&ap1302->ctrls, &ap1302_ctrls[i], NULL);
+
+	if (ap1302->ctrls.error) {
+		ret = ap1302->ctrls.error;
+		v4l2_ctrl_handler_free(&ap1302->ctrls);
+		return ret;
+	}
+
+	/* Use same lock for controls as for everything else. */
+	ap1302->ctrls.lock = &ap1302->lock;
+	ap1302->sd.ctrl_handler = &ap1302->ctrls;
+
+	return 0;
+}
+
+static void ap1302_ctrls_cleanup(struct ap1302_device *ap1302)
+{
+	v4l2_ctrl_handler_free(&ap1302->ctrls);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdev Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+ap1302_get_pad_format(struct ap1302_device *ap1302,
+		      struct v4l2_subdev_state *sd_state,
+		      unsigned int pad, u32 which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_format(&ap1302->sd, sd_state, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &ap1302->formats[pad].format;
+	default:
+		return NULL;
+	}
+}
+
+static int ap1302_init_cfg(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_state *sd_state)
+{
+	u32 which = sd_state ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	const struct ap1302_sensor_info *info = ap1302->sensor_info;
+	unsigned int pad;
+
+	for (pad = 0; pad < ARRAY_SIZE(ap1302->formats); ++pad) {
+		struct v4l2_mbus_framefmt *format =
+			ap1302_get_pad_format(ap1302, sd_state, pad, which);
+
+		format->width = info->resolution.width;
+		format->height = info->resolution.height;
+
+		/*
+		 * The source pad combines images side by side in multi-sensor
+		 * setup.
+		 */
+		if (pad == AP1302_PAD_SOURCE) {
+			format->width *= ap1302->width_factor;
+			format->code = ap1302->formats[pad].info->code;
+		} else {
+			format->code = info->format;
+		}
+
+		format->field = V4L2_FIELD_NONE;
+		format->colorspace = V4L2_COLORSPACE_SRGB;
+	}
+
+	return 0;
+}
+
+static int ap1302_enum_mbus_code(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+
+	if (code->pad != AP1302_PAD_SOURCE) {
+		/*
+		 * On the sink pads, only the format produced by the sensor is
+		 * supported.
+		 */
+		if (code->index)
+			return -EINVAL;
+
+		code->code = ap1302->sensor_info->format;
+	} else {
+		/* On the source pad, multiple formats are supported. */
+		if (code->index >= ARRAY_SIZE(supported_video_formats))
+			return -EINVAL;
+
+		code->code = supported_video_formats[code->index].code;
+	}
+
+	return 0;
+}
+
+static int ap1302_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	unsigned int i;
+
+	if (fse->index)
+		return -EINVAL;
+
+	if (fse->pad != AP1302_PAD_SOURCE) {
+		/*
+		 * On the sink pads, only the size produced by the sensor is
+		 * supported.
+		 */
+		if (fse->code != ap1302->sensor_info->format)
+			return -EINVAL;
+
+		fse->min_width = ap1302->sensor_info->resolution.width;
+		fse->min_height = ap1302->sensor_info->resolution.height;
+		fse->max_width = ap1302->sensor_info->resolution.width;
+		fse->max_height = ap1302->sensor_info->resolution.height;
+	} else {
+		/*
+		 * On the source pad, the AP1302 can freely scale within the
+		 * scaler's limits.
+		 */
+		for (i = 0; i < ARRAY_SIZE(supported_video_formats); i++) {
+			if (supported_video_formats[i].code == fse->code)
+				break;
+		}
+
+		if (i >= ARRAY_SIZE(supported_video_formats))
+			return -EINVAL;
+
+		fse->min_width = AP1302_MIN_WIDTH * ap1302->width_factor;
+		fse->min_height = AP1302_MIN_HEIGHT;
+		fse->max_width = AP1302_MAX_WIDTH;
+		fse->max_height = AP1302_MAX_HEIGHT;
+	}
+
+	return 0;
+}
+
+static int ap1302_get_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_state *sd_state,
+			  struct v4l2_subdev_format *fmt)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	const struct v4l2_mbus_framefmt *format;
+
+	format = ap1302_get_pad_format(ap1302, sd_state, fmt->pad, fmt->which);
+
+	mutex_lock(&ap1302->lock);
+	fmt->format = *format;
+	mutex_unlock(&ap1302->lock);
+
+	return 0;
+}
+
+static int ap1302_set_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_state *sd_state,
+			  struct v4l2_subdev_format *fmt)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	const struct ap1302_format_info *info = NULL;
+	struct v4l2_mbus_framefmt *format;
+	unsigned int i;
+
+	/* Formats on the sink pads can't be changed. */
+	if (fmt->pad != AP1302_PAD_SOURCE)
+		return ap1302_get_fmt(sd, sd_state, fmt);
+
+	format = ap1302_get_pad_format(ap1302, sd_state, fmt->pad, fmt->which);
+
+	/* Validate the media bus code, default to the first supported value. */
+	for (i = 0; i < ARRAY_SIZE(supported_video_formats); i++) {
+		if (supported_video_formats[i].code == fmt->format.code) {
+			info = &supported_video_formats[i];
+			break;
+		}
+	}
+
+	if (!info)
+		info = &supported_video_formats[0];
+
+	/*
+	 * Clamp the size. The width must be a multiple of 4 (or 8 in the
+	 * dual-sensor case) and the height a multiple of 2.
+	 */
+	fmt->format.width = clamp(ALIGN_DOWN(fmt->format.width,
+					     4 * ap1302->width_factor),
+				  AP1302_MIN_WIDTH * ap1302->width_factor,
+				  AP1302_MAX_WIDTH);
+	fmt->format.height = clamp(ALIGN_DOWN(fmt->format.height, 2),
+				   AP1302_MIN_HEIGHT, AP1302_MAX_HEIGHT);
+
+	mutex_lock(&ap1302->lock);
+
+	format->width = fmt->format.width;
+	format->height = fmt->format.height;
+	format->code = info->code;
+
+	if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+		ap1302->formats[fmt->pad].info = info;
+
+	mutex_unlock(&ap1302->lock);
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int ap1302_get_selection(struct v4l2_subdev *sd,
+				struct v4l2_subdev_state *sd_state,
+				struct v4l2_subdev_selection *sel)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	const struct ap1302_size *resolution = &ap1302->sensor_info->resolution;
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_NATIVE_SIZE:
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+	case V4L2_SEL_TGT_CROP_DEFAULT:
+	case V4L2_SEL_TGT_CROP:
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = resolution->width * ap1302->width_factor;
+		sel->r.height = resolution->height;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int ap1302_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	int ret;
+
+	mutex_lock(&ap1302->lock);
+
+	if (enable == ap1302->streaming)
+		goto done;
+
+	if (enable) {
+		ret = ap1302_configure(ap1302);
+		if (ret < 0)
+			goto done;
+
+		ret = ap1302_stall(ap1302, false);
+	} else {
+		ret = ap1302_stall(ap1302, true);
+	}
+
+done:
+	mutex_unlock(&ap1302->lock);
+
+	if (ret < 0)
+		dev_err(ap1302->dev, "Failed to %s stream: %d\n",
+			enable ? "start" : "stop", ret);
+
+	return ret;
+}
+
+static const char * const ap1302_warnings[] = {
+	"HINF_BANDWIDTH",
+	"FLICKER_DETECTION",
+	"FACED_NE",
+	"SMILED_NE",
+	"HINF_OVERRUN",
+	NULL,
+	"FRAME_TOO_SMALL",
+	"MISSING_PHASES",
+	"SPOOF_UNDERRUN",
+	"JPEG_NOLAST",
+	"NO_IN_FREQ_SPEC",
+	"SINF0",
+	"SINF1",
+	"CAPTURE0",
+	"CAPTURE1",
+	"ISR_UNHANDLED",
+	"INTERLEAVE_SPOOF",
+	"INTERLEAVE_BUF",
+	"COORD_OUT_OF_RANGE",
+	"ICP_CLOCKING",
+	"SENSOR_CLOCKING",
+	"SENSOR_NO_IHDR",
+	"DIVIDE_BY_ZERO",
+	"INT0_UNDERRUN",
+	"INT1_UNDERRUN",
+	"SCRATCHPAD_TOO_BIG",
+	"OTP_RECORD_READ",
+	"NO_LSC_IN_OTP",
+	"GPIO_INT_LOST",
+	"NO_PDAF_DATA",
+	"FAR_PDAF_ACCESS_SKIP",
+	"PDAF_ERROR",
+	"ATM_TVI_BOUNDS",
+	"SIPM_0_RTY",
+	"SIPM_1_TRY",
+	"SIPM_0_NO_ACK",
+	"SIPM_1_NO_ACK",
+	"SMILE_DIS",
+	"DVS_DIS",
+	"TEST_DIS",
+	"SENSOR_LV2LV",
+	"SENSOR_FV2FV",
+	"FRAME_LOST",
+};
+
+static const char * const ap1302_lane_states[] = {
+	"stop_s",
+	"hs_req_s",
+	"lp_req_s",
+	"hs_s",
+	"lp_s",
+	"esc_req_s",
+	"turn_req_s",
+	"esc_s",
+	"esc_0",
+	"esc_1",
+	"turn_s",
+	"turn_mark",
+	"error_s",
+};
+
+static void ap1302_log_lane_state(struct ap1302_sensor *sensor,
+				  unsigned int index)
+{
+	static const char * const lp_states[] = {
+		"00", "10", "01", "11",
+	};
+
+	unsigned int counts[4][ARRAY_SIZE(ap1302_lane_states)];
+	unsigned int samples = 0;
+	unsigned int lane;
+	unsigned int i;
+	u32 first[4] = { 0, };
+	u32 last[4] = { 0, };
+	int ret;
+
+	memset(counts, 0, sizeof(counts));
+
+	for (i = 0; i < 1000; ++i) {
+		u32 values[4];
+
+		/*
+		 * Read the state of all lanes and skip read errors and invalid
+		 * values.
+		 */
+		for (lane = 0; lane < 4; ++lane) {
+			ret = ap1302_read(sensor->ap1302,
+					  AP1302_ADV_SINF_MIPI_INTERNAL_p_LANE_n_STAT(index, lane),
+					  &values[lane]);
+			if (ret < 0)
+				break;
+
+			if (AP1302_LANE_STATE(values[lane]) >=
+			    ARRAY_SIZE(ap1302_lane_states)) {
+				ret = -EINVAL;
+				break;
+			}
+		}
+
+		if (ret < 0)
+			continue;
+
+		/* Accumulate the samples and save the first and last states. */
+		for (lane = 0; lane < 4; ++lane)
+			counts[lane][AP1302_LANE_STATE(values[lane])]++;
+
+		if (!samples)
+			memcpy(first, values, sizeof(first));
+		memcpy(last, values, sizeof(last));
+
+		samples++;
+	}
+
+	if (!samples)
+		return;
+
+	/*
+	 * Print the LP state from the first sample, the error state from the
+	 * last sample, and the states accumulators for each lane.
+	 */
+	for (lane = 0; lane < 4; ++lane) {
+		u32 state = last[lane];
+		char error_msg[25] = "";
+
+		if (state & (AP1302_LANE_ERR | AP1302_LANE_ABORT)) {
+			unsigned int err = AP1302_LANE_ERR_STATE(state);
+			const char *err_state = NULL;
+
+			err_state = err < ARRAY_SIZE(ap1302_lane_states)
+				  ? ap1302_lane_states[err] : "INVALID";
+
+			snprintf(error_msg, sizeof(error_msg), "ERR (%s%s) %s LP%s",
+				 state & AP1302_LANE_ERR ? "E" : "",
+				 state & AP1302_LANE_ABORT ? "A" : "",
+				 err_state,
+				 lp_states[AP1302_LANE_ERR_LP_VAL(state)]);
+		}
+
+		dev_info(sensor->ap1302->dev, "SINF%u L%u state: LP%s %s",
+			 index, lane, lp_states[AP1302_LANE_LP_VAL(first[lane])],
+			 error_msg);
+
+		for (i = 0; i < ARRAY_SIZE(ap1302_lane_states); ++i) {
+			if (counts[lane][i])
+				pr_cont(" %s:%u",
+				       ap1302_lane_states[i],
+				       counts[lane][i]);
+		}
+		pr_cont("\n");
+	}
+
+	/* Reset the error flags. */
+	for (lane = 0; lane < 4; ++lane)
+		ap1302_write(sensor->ap1302,
+			     AP1302_ADV_SINF_MIPI_INTERNAL_p_LANE_n_STAT(index, lane),
+			     AP1302_LANE_ERR | AP1302_LANE_ABORT, NULL);
+}
+
+static int ap1302_log_status(struct v4l2_subdev *sd)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	u16 frame_count_icp;
+	u16 frame_count_brac;
+	u16 frame_count_hinf;
+	u32 warning[4];
+	u32 error[3];
+	unsigned int i;
+	u32 value;
+	int ret;
+
+	/* Dump the console buffer. */
+	ret = ap1302_dump_console(ap1302);
+	if (ret < 0)
+		return ret;
+
+	/* Print errors. */
+	ret = ap1302_read(ap1302, AP1302_ERROR, &error[0]);
+	if (ret < 0)
+		return ret;
+
+	ret = ap1302_read(ap1302, AP1302_ERR_FILE, &error[1]);
+	if (ret < 0)
+		return ret;
+
+	ret = ap1302_read(ap1302, AP1302_ERR_LINE, &error[2]);
+	if (ret < 0)
+		return ret;
+
+	dev_info(ap1302->dev, "ERROR: 0x%04x (file 0x%08x:%u)\n",
+		 error[0], error[1], error[2]);
+
+	ret = ap1302_read(ap1302, AP1302_SIPM_ERR_0, &error[0]);
+	if (ret < 0)
+		return ret;
+
+	ret = ap1302_read(ap1302, AP1302_SIPM_ERR_1, &error[1]);
+	if (ret < 0)
+		return ret;
+
+	dev_info(ap1302->dev, "SIPM_ERR [0] 0x%04x [1] 0x%04x\n",
+		 error[0], error[1]);
+
+	/* Print warnings. */
+	for (i = 0; i < ARRAY_SIZE(warning); ++i) {
+		ret = ap1302_read(ap1302, AP1302_WARNING(i), &warning[i]);
+		if (ret < 0)
+			return ret;
+	}
+
+	dev_info(ap1302->dev,
+		 "WARNING [0] 0x%04x [1] 0x%04x [2] 0x%04x [3] 0x%04x\n",
+		 warning[0], warning[1], warning[2], warning[3]);
+
+	for (i = 0; i < ARRAY_SIZE(ap1302_warnings); ++i) {
+		if ((warning[i / 16] & BIT(i % 16)) &&
+		    ap1302_warnings[i])
+			dev_info(ap1302->dev, "- WARN_%s\n",
+				 ap1302_warnings[i]);
+	}
+
+	/* Print the frame counter. */
+	ret = ap1302_read(ap1302, AP1302_FRAME_CNT, &value);
+	if (ret < 0)
+		return ret;
+
+	frame_count_hinf = value >> 8;
+	frame_count_brac = value & 0xff;
+
+	ret = ap1302_read(ap1302, AP1302_ADV_CAPTURE_A_FV_CNT, &value);
+	if (ret < 0)
+		return ret;
+
+	frame_count_icp = value & 0xffff;
+
+	dev_info(ap1302->dev, "Frame counters: ICP %u, HINF %u, BRAC %u\n",
+		 frame_count_icp, frame_count_hinf, frame_count_brac);
+
+	/* Sample the lane state. */
+	for (i = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		struct ap1302_sensor *sensor = &ap1302->sensors[i];
+
+		if (!sensor->ap1302)
+			continue;
+
+		ap1302_log_lane_state(sensor, i);
+	}
+
+	return 0;
+}
+
+static int ap1302_subdev_registered(struct v4l2_subdev *sd)
+{
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		struct ap1302_sensor *sensor = &ap1302->sensors[i];
+
+		if (!sensor->dev)
+			continue;
+
+		dev_dbg(ap1302->dev, "registering sensor %u\n", i);
+
+		ret = v4l2_device_register_subdev(sd->v4l2_dev, &sensor->sd);
+		if (ret)
+			return ret;
+
+		ret = media_create_pad_link(&sensor->sd.entity, 0,
+					    &sd->entity, i,
+					    MEDIA_LNK_FL_IMMUTABLE |
+					    MEDIA_LNK_FL_ENABLED);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static const struct media_entity_operations ap1302_media_ops = {
+	.link_validate = v4l2_subdev_link_validate
+};
+
+static const struct v4l2_subdev_pad_ops ap1302_pad_ops = {
+	.init_cfg = ap1302_init_cfg,
+	.enum_mbus_code = ap1302_enum_mbus_code,
+	.enum_frame_size = ap1302_enum_frame_size,
+	.get_fmt = ap1302_get_fmt,
+	.set_fmt = ap1302_set_fmt,
+	.get_selection = ap1302_get_selection,
+	.set_selection = ap1302_get_selection,
+};
+
+static const struct v4l2_subdev_video_ops ap1302_video_ops = {
+	.s_stream = ap1302_s_stream,
+};
+
+static const struct v4l2_subdev_core_ops ap1302_core_ops = {
+	.log_status = ap1302_log_status,
+};
+
+static const struct v4l2_subdev_ops ap1302_subdev_ops = {
+	.core = &ap1302_core_ops,
+	.video = &ap1302_video_ops,
+	.pad = &ap1302_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops ap1302_subdev_internal_ops = {
+	.registered = ap1302_subdev_registered,
+};
+
+/* -----------------------------------------------------------------------------
+ * Sensor
+ */
+
+static int ap1302_sensor_enum_mbus_code(struct v4l2_subdev *sd,
+					struct v4l2_subdev_state *sd_state,
+					struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ap1302_sensor *sensor = to_ap1302_sensor(sd);
+	const struct ap1302_sensor_info *info = sensor->ap1302->sensor_info;
+
+	if (code->index)
+		return -EINVAL;
+
+	code->code = info->format;
+	return 0;
+}
+
+static int ap1302_sensor_enum_frame_size(struct v4l2_subdev *sd,
+					 struct v4l2_subdev_state *sd_state,
+					 struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct ap1302_sensor *sensor = to_ap1302_sensor(sd);
+	const struct ap1302_sensor_info *info = sensor->ap1302->sensor_info;
+
+	if (fse->index)
+		return -EINVAL;
+
+	if (fse->code != info->format)
+		return -EINVAL;
+
+	fse->min_width = info->resolution.width;
+	fse->min_height = info->resolution.height;
+	fse->max_width = info->resolution.width;
+	fse->max_height = info->resolution.height;
+
+	return 0;
+}
+
+static int ap1302_sensor_get_fmt(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct ap1302_sensor *sensor = to_ap1302_sensor(sd);
+	const struct ap1302_sensor_info *info = sensor->ap1302->sensor_info;
+
+	memset(&fmt->format, 0, sizeof(fmt->format));
+
+	fmt->format.width = info->resolution.width;
+	fmt->format.height = info->resolution.height;
+	fmt->format.field = V4L2_FIELD_NONE;
+	fmt->format.code = info->format;
+	fmt->format.colorspace = V4L2_COLORSPACE_SRGB;
+
+	return 0;
+}
+
+static const struct v4l2_subdev_pad_ops ap1302_sensor_pad_ops = {
+	.enum_mbus_code = ap1302_sensor_enum_mbus_code,
+	.enum_frame_size = ap1302_sensor_enum_frame_size,
+	.get_fmt = ap1302_sensor_get_fmt,
+	.set_fmt = ap1302_sensor_get_fmt,
+};
+
+static const struct v4l2_subdev_ops ap1302_sensor_subdev_ops = {
+	.pad = &ap1302_sensor_pad_ops,
+};
+
+static int ap1302_sensor_parse_of(struct ap1302_device *ap1302,
+				  struct device_node *node)
+{
+	struct ap1302_sensor *sensor;
+	u32 reg;
+	int ret;
+
+	/* Retrieve the sensor index from the reg property. */
+	ret = of_property_read_u32(node, "reg", &reg);
+	if (ret < 0) {
+		dev_warn(ap1302->dev,
+			 "'reg' property missing in sensor node\n");
+		return -EINVAL;
+	}
+
+	if (reg >= ARRAY_SIZE(ap1302->sensors)) {
+		dev_warn(ap1302->dev, "Out-of-bounds 'reg' value %u\n",
+			 reg);
+		return -EINVAL;
+	}
+
+	sensor = &ap1302->sensors[reg];
+	if (sensor->ap1302) {
+		dev_warn(ap1302->dev, "Duplicate entry for sensor %u\n", reg);
+		return -EINVAL;
+	}
+
+	sensor->ap1302 = ap1302;
+	sensor->of_node = of_node_get(node);
+
+	return 0;
+}
+
+static void ap1302_sensor_dev_release(struct device *dev)
+{
+	of_node_put(dev->of_node);
+	kfree(dev);
+}
+
+static int ap1302_sensor_init(struct ap1302_sensor *sensor, unsigned int index)
+{
+	struct ap1302_device *ap1302 = sensor->ap1302;
+	struct v4l2_subdev *sd = &sensor->sd;
+	unsigned int i;
+	int ret;
+
+	sensor->index = index;
+
+	/*
+	 * Register a device for the sensor, to support usage of the regulator
+	 * API.
+	 */
+	sensor->dev = kzalloc(sizeof(*sensor->dev), GFP_KERNEL);
+	if (!sensor->dev)
+		return -ENOMEM;
+
+	sensor->dev->parent = ap1302->dev;
+	sensor->dev->of_node = of_node_get(sensor->of_node);
+	sensor->dev->release = &ap1302_sensor_dev_release;
+	dev_set_name(sensor->dev, "%s-%s.%u", dev_name(ap1302->dev),
+		     ap1302->sensor_info->name, index);
+
+	ret = device_register(sensor->dev);
+	if (ret < 0) {
+		dev_err(ap1302->dev,
+			"Failed to register device for sensor %u\n", index);
+		goto error;
+	}
+
+	/* Retrieve the power supplies for the sensor, if any. */
+	if (ap1302->sensor_info->supplies) {
+		const struct ap1302_sensor_supply *supplies =
+			ap1302->sensor_info->supplies;
+		unsigned int num_supplies;
+
+		for (num_supplies = 0; supplies[num_supplies].name; ++num_supplies)
+			;
+
+		sensor->supplies = devm_kcalloc(ap1302->dev, num_supplies,
+						sizeof(*sensor->supplies),
+						GFP_KERNEL);
+		if (!sensor->supplies) {
+			ret = -ENOMEM;
+			goto error;
+		}
+
+		for (i = 0; i < num_supplies; ++i)
+			sensor->supplies[i].supply = supplies[i].name;
+
+		ret = regulator_bulk_get(sensor->dev, num_supplies,
+					 sensor->supplies);
+		if (ret < 0) {
+			dev_err(ap1302->dev,
+				"Failed to get supplies for sensor %u\n", index);
+			goto error;
+		}
+
+		sensor->num_supplies = i;
+	}
+
+	sd->dev = sensor->dev;
+	v4l2_subdev_init(sd, &ap1302_sensor_subdev_ops);
+
+	snprintf(sd->name, sizeof(sd->name), "%s %u",
+		 ap1302->sensor_info->name, index);
+
+	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	sd->entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+	ret = media_entity_pads_init(&sd->entity, 1, &sensor->pad);
+	if (ret < 0) {
+		dev_err(ap1302->dev,
+			"failed to initialize media entity for sensor %u: %d\n",
+			index, ret);
+		goto error;
+	}
+
+	return 0;
+
+error:
+	put_device(sensor->dev);
+	return ret;
+}
+
+static void ap1302_sensor_cleanup(struct ap1302_sensor *sensor)
+{
+	media_entity_cleanup(&sensor->sd.entity);
+
+	if (sensor->num_supplies)
+		regulator_bulk_free(sensor->num_supplies, sensor->supplies);
+
+	put_device(sensor->dev);
+	of_node_put(sensor->of_node);
+}
+
+/* -----------------------------------------------------------------------------
+ * Boot & Firmware Handling
+ */
+
+static int ap1302_request_firmware(struct ap1302_device *ap1302)
+{
+	static const char * const suffixes[] = {
+		"",
+		"_single",
+		"_dual",
+	};
+
+	const struct ap1302_firmware_header *fw_hdr;
+	unsigned int num_sensors;
+	unsigned int fw_size;
+	unsigned int i;
+	char name[64];
+	int ret;
+
+	for (i = 0, num_sensors = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		if (ap1302->sensors[i].dev)
+			num_sensors++;
+	}
+
+	ret = snprintf(name, sizeof(name), "ap1302_%s%s_fw.bin",
+		       ap1302->sensor_info->name, suffixes[num_sensors]);
+	if (ret >= sizeof(name)) {
+		dev_err(ap1302->dev, "Firmware name too long\n");
+		return -EINVAL;
+	}
+
+	dev_dbg(ap1302->dev, "Requesting firmware %s\n", name);
+
+	ret = request_firmware(&ap1302->fw, name, ap1302->dev);
+	if (ret) {
+		dev_err(ap1302->dev, "Failed to request firmware: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * The firmware binary contains a header defined by the
+	 * ap1302_firmware_header structure. The firmware itself (also referred
+	 * to as bootdata) follows the header. Perform sanity checks to ensure
+	 * the firmware is valid.
+	 */
+	fw_hdr = (const struct ap1302_firmware_header *)ap1302->fw->data;
+	fw_size = ap1302->fw->size - sizeof(*fw_hdr);
+
+	if (fw_hdr->pll_init_size > fw_size) {
+		dev_err(ap1302->dev,
+			"Invalid firmware: PLL init size too large\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/*
+ * ap1302_write_fw_window() - Write a piece of firmware to the AP1302
+ * @win_pos: Firmware load window current position
+ * @buf: Firmware data buffer
+ * @len: Firmware data length
+ *
+ * The firmware is loaded through a window in the registers space. Writes are
+ * sequential starting at address 0x8000, and must wrap around when reaching
+ * 0x9fff. This function write the firmware data stored in @buf to the AP1302,
+ * keeping track of the window position in the @win_pos argument.
+ */
+static int ap1302_write_fw_window(struct ap1302_device *ap1302, const u8 *buf,
+				  u32 len, unsigned int *win_pos)
+{
+	while (len > 0) {
+		unsigned int write_addr;
+		unsigned int write_size;
+		int ret;
+
+		/*
+		 * Write at most len bytes, from the current position to the
+		 * end of the window.
+		 */
+		write_addr = *win_pos + AP1302_FW_WINDOW_OFFSET;
+		write_size = min(len, AP1302_FW_WINDOW_SIZE - *win_pos);
+
+		ret = regmap_raw_write(ap1302->regmap16, write_addr, buf,
+				       write_size);
+		if (ret)
+			return ret;
+
+		buf += write_size;
+		len -= write_size;
+
+		*win_pos += write_size;
+		if (*win_pos >= AP1302_FW_WINDOW_SIZE)
+			*win_pos = 0;
+	}
+
+	return 0;
+}
+
+static int ap1302_load_firmware(struct ap1302_device *ap1302)
+{
+	const struct ap1302_firmware_header *fw_hdr;
+	unsigned int fw_size;
+	const u8 *fw_data;
+	unsigned int win_pos = 0;
+	unsigned int crc;
+	int ret;
+
+	fw_hdr = (const struct ap1302_firmware_header *)ap1302->fw->data;
+	fw_data = (u8 *)&fw_hdr[1];
+	fw_size = ap1302->fw->size - sizeof(*fw_hdr);
+
+	/* Clear the CRC register. */
+	ret = ap1302_write(ap1302, AP1302_SIP_CRC, 0xffff, NULL);
+	if (ret)
+		return ret;
+
+	/*
+	 * Load the PLL initialization settings, set the bootdata stage to 2 to
+	 * apply the basic_init_hp settings, and wait 1ms for the PLL to lock.
+	 */
+	ret = ap1302_write_fw_window(ap1302, fw_data, fw_hdr->pll_init_size,
+				     &win_pos);
+	if (ret)
+		return ret;
+
+	ret = ap1302_write(ap1302, AP1302_BOOTDATA_STAGE, 0x0002, NULL);
+	if (ret)
+		return ret;
+
+	usleep_range(1000, 2000);
+
+	/* Load the rest of the bootdata content and verify the CRC. */
+	ret = ap1302_write_fw_window(ap1302, fw_data + fw_hdr->pll_init_size,
+				     fw_size - fw_hdr->pll_init_size, &win_pos);
+	if (ret)
+		return ret;
+
+	msleep(40);
+
+	ret = ap1302_read(ap1302, AP1302_SIP_CRC, &crc);
+	if (ret)
+		return ret;
+
+	if (crc != fw_hdr->crc) {
+		dev_warn(ap1302->dev,
+			 "CRC mismatch: expected 0x%04x, got 0x%04x\n",
+			 fw_hdr->crc, crc);
+		return -EAGAIN;
+	}
+
+	/*
+	 * Write 0xffff to the bootdata_stage register to indicate to the
+	 * AP1302 that the whole bootdata content has been loaded.
+	 */
+	ret = ap1302_write(ap1302, AP1302_BOOTDATA_STAGE, 0xffff, NULL);
+	if (ret)
+		return ret;
+
+	/* The AP1302 starts outputting frames right after boot, stop it. */
+	ret = ap1302_stall(ap1302, true);
+	if (ret)
+		return ret;
+
+	/* Adjust MIPI TCLK timings */
+	return ap1302_set_mipi_t3_clk(ap1302);
+}
+
+static int ap1302_detect_chip(struct ap1302_device *ap1302)
+{
+	unsigned int version;
+	unsigned int revision;
+	int ret;
+
+	ret = ap1302_read(ap1302, AP1302_CHIP_VERSION, &version);
+	if (ret)
+		return ret;
+
+	ret = ap1302_read(ap1302, AP1302_CHIP_REV, &revision);
+	if (ret)
+		return ret;
+
+	if (version != AP1302_CHIP_ID) {
+		dev_err(ap1302->dev,
+			"Invalid chip version, expected 0x%04x, got 0x%04x\n",
+			AP1302_CHIP_ID, version);
+		return -EINVAL;
+	}
+
+	dev_info(ap1302->dev, "AP1302 revision %u.%u.%u detected\n",
+		 (revision & 0xf000) >> 12, (revision & 0x0f00) >> 8,
+		 revision & 0x00ff);
+
+	return 0;
+}
+
+static int ap1302_hw_init(struct ap1302_device *ap1302)
+{
+	unsigned int retries;
+	int ret;
+
+	/* Request and validate the firmware. */
+	ret = ap1302_request_firmware(ap1302);
+	if (ret)
+		return ret;
+
+	/*
+	 * Power the sensors first, as the firmware will access them once it
+	 * gets loaded.
+	 */
+	ret = ap1302_power_on_sensors(ap1302);
+	if (ret < 0)
+		goto error_firmware;
+
+	/*
+	 * Load the firmware, retrying in case of CRC errors. The AP1302 is
+	 * reset with a full power cycle between each attempt.
+	 */
+	for (retries = 0; retries < MAX_FW_LOAD_RETRIES; ++retries) {
+		ret = ap1302_power_on(ap1302);
+		if (ret < 0)
+			goto error_power_sensors;
+
+		ret = ap1302_detect_chip(ap1302);
+		if (ret)
+			goto error_power;
+
+		ret = ap1302_load_firmware(ap1302);
+		if (!ret)
+			break;
+
+		if (ret != -EAGAIN)
+			goto error_power;
+
+		ap1302_power_off(ap1302);
+	}
+
+	if (retries == MAX_FW_LOAD_RETRIES) {
+		dev_err(ap1302->dev,
+			"Firmware load retries exceeded, aborting\n");
+		ret = -ETIMEDOUT;
+		goto error_power_sensors;
+	}
+
+	return 0;
+
+error_power:
+	ap1302_power_off(ap1302);
+error_power_sensors:
+	ap1302_power_off_sensors(ap1302);
+error_firmware:
+	release_firmware(ap1302->fw);
+
+	return ret;
+}
+
+static void ap1302_hw_cleanup(struct ap1302_device *ap1302)
+{
+	ap1302_power_off(ap1302);
+	ap1302_power_off_sensors(ap1302);
+}
+
+/* -----------------------------------------------------------------------------
+ * Probe & Remove
+ */
+
+static int ap1302_config_v4l2(struct ap1302_device *ap1302)
+{
+	struct v4l2_subdev *sd;
+	unsigned int i;
+	int ret;
+
+	sd = &ap1302->sd;
+	sd->dev = ap1302->dev;
+	v4l2_i2c_subdev_init(sd, ap1302->client, &ap1302_subdev_ops);
+
+	strscpy(sd->name, DRIVER_NAME, sizeof(sd->name));
+	strlcat(sd->name, ".", sizeof(sd->name));
+	strlcat(sd->name, dev_name(ap1302->dev), sizeof(sd->name));
+	dev_dbg(ap1302->dev, "name %s\n", sd->name);
+
+	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	sd->internal_ops = &ap1302_subdev_internal_ops;
+	sd->entity.function = MEDIA_ENT_F_PROC_VIDEO_ISP;
+	sd->entity.ops = &ap1302_media_ops;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->pads); ++i)
+		ap1302->pads[i].flags = i == AP1302_PAD_SOURCE
+				      ? MEDIA_PAD_FL_SOURCE : MEDIA_PAD_FL_SINK;
+
+	ret = media_entity_pads_init(&sd->entity, ARRAY_SIZE(ap1302->pads),
+				     ap1302->pads);
+	if (ret < 0) {
+		dev_err(ap1302->dev, "media_entity_init failed %d\n", ret);
+		return ret;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->formats); ++i)
+		ap1302->formats[i].info = &supported_video_formats[0];
+
+	ret = ap1302_init_cfg(sd, NULL);
+	if (ret < 0)
+		goto error_media;
+
+	ret = ap1302_ctrls_init(ap1302);
+	if (ret < 0)
+		goto error_media;
+
+	ret = v4l2_async_register_subdev(sd);
+	if (ret < 0) {
+		dev_err(ap1302->dev, "v4l2_async_register_subdev failed %d\n", ret);
+		goto error_ctrls;
+	}
+
+	return 0;
+
+error_ctrls:
+	ap1302_ctrls_cleanup(ap1302);
+error_media:
+	media_entity_cleanup(&sd->entity);
+	return ret;
+}
+
+static int ap1302_parse_of(struct ap1302_device *ap1302)
+{
+	struct device_node *sensors;
+	struct device_node *node;
+	struct fwnode_handle *ep;
+	unsigned int num_sensors = 0;
+	const char *model;
+	unsigned int i;
+	int ret;
+
+	/* Clock */
+	ap1302->clock = devm_clk_get(ap1302->dev, NULL);
+	if (IS_ERR(ap1302->clock)) {
+		dev_err(ap1302->dev, "Failed to get clock: %ld\n",
+			PTR_ERR(ap1302->clock));
+		return PTR_ERR(ap1302->clock);
+	}
+
+	/* GPIOs */
+	ap1302->reset_gpio = devm_gpiod_get(ap1302->dev, "reset",
+					    GPIOD_OUT_HIGH);
+	if (IS_ERR(ap1302->reset_gpio)) {
+		dev_err(ap1302->dev, "Can't get reset GPIO: %ld\n",
+			PTR_ERR(ap1302->reset_gpio));
+		return PTR_ERR(ap1302->reset_gpio);
+	}
+
+	ap1302->standby_gpio = devm_gpiod_get_optional(ap1302->dev, "standby",
+						       GPIOD_OUT_LOW);
+	if (IS_ERR(ap1302->standby_gpio)) {
+		dev_err(ap1302->dev, "Can't get standby GPIO: %ld\n",
+			PTR_ERR(ap1302->standby_gpio));
+		return PTR_ERR(ap1302->standby_gpio);
+	}
+
+	/* Bus configuration */
+	ep = fwnode_graph_get_next_endpoint(dev_fwnode(ap1302->dev), NULL);
+	if (!ep)
+		return -EINVAL;
+
+	ap1302->bus_cfg.bus_type = V4L2_MBUS_CSI2_DPHY;
+
+	ret = v4l2_fwnode_endpoint_alloc_parse(ep, &ap1302->bus_cfg);
+	if (ret < 0) {
+		dev_err(ap1302->dev, "Failed to parse bus configuration\n");
+		return ret;
+	}
+
+	/* Sensors */
+	sensors = of_get_child_by_name(ap1302->dev->of_node, "sensors");
+	if (!sensors) {
+		dev_err(ap1302->dev, "'sensors' child node not found\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_string(sensors, "onnn,model", &model);
+	if (ret < 0) {
+		/*
+		 * If no sensor is connected, we can still support operation
+		 * with the test pattern generator.
+		 */
+		ap1302->sensor_info = &ap1302_sensor_info_tpg;
+		ap1302->width_factor = 1;
+		ret = 0;
+		goto done;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ap1302_sensor_info); ++i) {
+		const struct ap1302_sensor_info *info =
+			&ap1302_sensor_info[i];
+
+		if (!strcmp(info->model, model)) {
+			ap1302->sensor_info = info;
+			break;
+		}
+	}
+
+	if (!ap1302->sensor_info) {
+		dev_warn(ap1302->dev, "Unsupported sensor model %s\n", model);
+		ret = -EINVAL;
+		goto done;
+	}
+
+	for_each_child_of_node(sensors, node) {
+		if (of_node_name_eq(node, "sensor")) {
+			if (!ap1302_sensor_parse_of(ap1302, node))
+				num_sensors++;
+		}
+	}
+
+	if (!num_sensors) {
+		dev_err(ap1302->dev, "No sensor found\n");
+		ret = -EINVAL;
+		goto done;
+	}
+
+	ap1302->width_factor = num_sensors;
+
+done:
+	of_node_put(sensors);
+	return ret;
+}
+
+static void ap1302_cleanup(struct ap1302_device *ap1302)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		struct ap1302_sensor *sensor = &ap1302->sensors[i];
+
+		if (!sensor->ap1302)
+			continue;
+
+		ap1302_sensor_cleanup(sensor);
+	}
+
+	v4l2_fwnode_endpoint_free(&ap1302->bus_cfg);
+
+	mutex_destroy(&ap1302->lock);
+}
+
+static int ap1302_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct ap1302_device *ap1302;
+	unsigned int i;
+	int ret;
+
+	ap1302 = devm_kzalloc(&client->dev, sizeof(*ap1302), GFP_KERNEL);
+	if (!ap1302)
+		return -ENOMEM;
+
+	ap1302->dev = &client->dev;
+	ap1302->client = client;
+
+	mutex_init(&ap1302->lock);
+
+	ap1302->regmap16 = devm_regmap_init_i2c(client, &ap1302_reg16_config);
+	if (IS_ERR(ap1302->regmap16)) {
+		dev_err(ap1302->dev, "regmap16 init failed: %ld\n",
+			PTR_ERR(ap1302->regmap16));
+		ret = -ENODEV;
+		goto error;
+	}
+
+	ap1302->regmap32 = devm_regmap_init_i2c(client, &ap1302_reg32_config);
+	if (IS_ERR(ap1302->regmap32)) {
+		dev_err(ap1302->dev, "regmap32 init failed: %ld\n",
+			PTR_ERR(ap1302->regmap32));
+		ret = -ENODEV;
+		goto error;
+	}
+
+	ret = ap1302_parse_of(ap1302);
+	if (ret < 0)
+		goto error;
+
+	for (i = 0; i < ARRAY_SIZE(ap1302->sensors); ++i) {
+		struct ap1302_sensor *sensor = &ap1302->sensors[i];
+
+		if (!sensor->ap1302)
+			continue;
+
+		ret = ap1302_sensor_init(sensor, i);
+		if (ret < 0)
+			goto error;
+	}
+
+	ret = ap1302_hw_init(ap1302);
+	if (ret)
+		goto error;
+
+	ap1302_debugfs_init(ap1302);
+
+	ret = ap1302_config_v4l2(ap1302);
+	if (ret)
+		goto error_hw_cleanup;
+
+	return 0;
+
+error_hw_cleanup:
+	ap1302_hw_cleanup(ap1302);
+error:
+	ap1302_cleanup(ap1302);
+	return ret;
+}
+
+static int ap1302_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ap1302_device *ap1302 = to_ap1302(sd);
+
+	ap1302_debugfs_cleanup(ap1302);
+
+	ap1302_hw_cleanup(ap1302);
+
+	release_firmware(ap1302->fw);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+
+	ap1302_ctrls_cleanup(ap1302);
+
+	ap1302_cleanup(ap1302);
+
+	return 0;
+}
+
+static const struct of_device_id ap1302_of_id_table[] = {
+	{ .compatible = "onnn,ap1302" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ap1302_of_id_table);
+
+static struct i2c_driver ap1302_i2c_driver = {
+	.driver = {
+		.name	= DRIVER_NAME,
+		.of_match_table	= ap1302_of_id_table,
+	},
+	.probe		= ap1302_probe,
+	.remove		= ap1302_remove,
+};
+
+module_i2c_driver(ap1302_i2c_driver);
+
+MODULE_AUTHOR("Florian Rebaudo <frebaudo@witekio.com>");
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_AUTHOR("Anil Kumar M <anil.mamidala@xilinx.com>");
+
+MODULE_DESCRIPTION("ON Semiconductor AP1302 ISP driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ar1335.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ar1335.c
@@ -0,0 +1,1458 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AR1335 driver
+ *
+ * Copyright (C) 2014-2015, NVIDIA CORPORATION, All Rights Reserved.
+ * Copyright (C) 2020 Xilinx, Inc.
+ * Copyright (C) 2023 Advanced Micro Devices, Inc.
+ *
+ * Contacts: Anil Kumar Mamidala <anil.mamidal@amd.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/i2c.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+
+#define AR1335_NAME "ar1335"
+#define AR1335_TABLE_WAIT_MS 0
+#define AR1335_TABLE_END 1
+#define AR1335_MAX_RETRIES 3
+#define AR1335_WAIT_MS 100
+#define AR1335_DEFAULT_WIDTH 1920
+#define AR1335_DEFAULT_HEIGHT 1080
+#define AR1335_DEF_FRAME_RATE 30
+#define AR1335_MAX_RATIO_MISMATCH 10
+#define AR1335_FRAME_LENGTH_ADDR 0x300A
+#define AR1335_COARSE_TIME_ADDR 0x3012
+#define MAX_FRAME_RATE 60
+#define MIN_FRAME_RATE 30
+#define V4L2_CID_HDR_MODE (V4L2_CID_CAMERA_CLASS_BASE + 1045)
+#define V4L2_CID_DEFECT_CORRECTION (V4L2_CID_CAMERA_CLASS_BASE + 1046)
+#define V4L2_CID_LENGTH_LINE_PCK (V4L2_CID_CAMERA_CLASS_BASE + 1047)
+#define V4L2_CID_COARSE_INT_TIME (V4L2_CID_CAMERA_CLASS_BASE + 1048)
+#define V4L2_CID_COLOR_FORMAT (V4L2_CID_CAMERA_CLASS_BASE + 1049)
+#define to_ar1335_device(sub_dev)                                              \
+	container_of(sub_dev, struct ar1335_device, sd)
+
+struct ar1335_reg {
+	u16 addr;
+	u16 val;
+};
+
+struct ar1335_res_struct {
+	u16 width;
+	u16 height;
+	u16 out_fmt;
+	u16 fps;
+	struct ar1335_reg *ar1335_mode;
+};
+
+struct ar1335_context_res {
+	s32 res_num;
+	s32 cur_res;
+	struct ar1335_res_struct *res_table;
+};
+
+struct ar1335_device {
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	const struct firmware *fw;
+	struct mutex input_lock; /* serialize sensor's ioctl */
+	struct v4l2_mbus_framefmt format;
+	struct v4l2_fract frame_rate;
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_ctrl *test_pattern;
+	struct ar1335_res_struct *res_table;
+	s32 cur_res;
+	unsigned int num_lanes;
+	struct gpio_desc *rst_gpio;
+	struct regmap *regmap16;
+	bool sys_activated;
+	bool sys_init;
+};
+
+struct ar1335_firmware {
+	u32 crc;
+	u32 pll_init_size;
+	u32 total_size;
+	u32 reserved;
+};
+
+struct ar1335_context_info {
+	u16 offset;
+	u16 len;
+	char *name;
+};
+
+static struct ar1335_reg ar1335_init[] = {
+	{0x301A, 0x0210},
+	{0x3EB6, 0x004D},
+	{0x3EBC, 0xAA06},
+	{0x3EC0, 0x1E02},
+	{0x3EC2, 0x7700},
+	{0x3EC4, 0x1C08},
+	{0x3EC6, 0xEA44},
+	{0x3EC8, 0x0F0F},
+	{0x3ECA, 0x0F4A},
+	{0x3ECC, 0x0706},
+	{0x3ECE, 0x443B},
+	{0x3ED0, 0x12F0},
+	{0x3ED2, 0x0039},
+	{0x3ED4, 0x862F},
+	{0x3ED6, 0x4080},
+	{0x3ED8, 0x0523},
+	{0x3EDA, 0xF896},
+	{0x3EDC, 0x508C},
+	{0x3EDE, 0x5005},
+	{0x316A, 0x8200},
+	{0x316E, 0x8200},
+	{0x316C, 0x8200},
+	{0x3EF0, 0x414D},
+	{0x3EF2, 0x0101},
+	{0x3EF6, 0x0307},
+	{0x3EFA, 0x0F0F},
+	{0x3EFC, 0x0F0F},
+	{0x3EFE, 0x0F0F},
+	{0x3D00, 0x0446},
+	{0x3D02, 0x4C66},
+	{0x3D04, 0xFFFF},
+	{0x3D06, 0xFFFF},
+	{0x3D08, 0x5E40},
+	{0x3D0A, 0x1146},
+	{0x3D0C, 0x5D41},
+	{0x3D0E, 0x1088},
+	{0x3D10, 0x8342},
+	{0x3D12, 0x00C0},
+	{0x3D14, 0x5580},
+	{0x3D16, 0x5B83},
+	{0x3D18, 0x6084},
+	{0x3D1A, 0x5A8D},
+	{0x3D1C, 0x00C0},
+	{0x3D1E, 0x8342},
+	{0x3D20, 0x925A},
+	{0x3D22, 0x8664},
+	{0x3D24, 0x1030},
+	{0x3D26, 0x801C},
+	{0x3D28, 0x00A0},
+	{0x3D2A, 0x56B0},
+	{0x3D2C, 0x5788},
+	{0x3D2E, 0x5150},
+	{0x3D30, 0x824D},
+	{0x3D32, 0x8D58},
+	{0x3D34, 0x58D2},
+	{0x3D36, 0x438A},
+	{0x3D38, 0x4592},
+	{0x3D3A, 0x458A},
+	{0x3D3C, 0x4389},
+	{0x3D3E, 0x51FF},
+	{0x3D40, 0x8451},
+	{0x3D42, 0x8410},
+	{0x3D44, 0x0C88},
+	{0x3D46, 0x5959},
+	{0x3D48, 0x8A5F},
+	{0x3D4A, 0xDA42},
+	{0x3D4C, 0x9361},
+	{0x3D4E, 0X8262},
+	{0x3D50, 0x8342},
+	{0x3D52, 0x8010},
+	{0x3D54, 0xC041},
+	{0x3D56, 0x64FF},
+	{0x3D58, 0xFFB7},
+	{0x3D5A, 0x4081},
+	{0x3D5C, 0x4080},
+	{0x3D5E, 0x4180},
+	{0x3D60, 0x4280},
+	{0x3D62, 0x438D},
+	{0x3D64, 0x44BA},
+	{0x3D66, 0x4488},
+	{0x3D68, 0x4380},
+	{0x3D6A, 0x4241},
+	{0x3D6C, 0x8140},
+	{0x3D6E, 0x8240},
+	{0x3D70, 0x8041},
+	{0x3D72, 0x8042},
+	{0x3D74, 0x8043},
+	{0x3D76, 0x8D44},
+	{0x3D78, 0xBA44},
+	{0x3D7A, 0x875E},
+	{0x3D7C, 0x4354},
+	{0x3D7E, 0x4241},
+	{0x3D80, 0x8140},
+	{0x3D82, 0x8120},
+	{0x3D84, 0x2881},
+	{0x3D86, 0x6026},
+	{0x3D88, 0x8055},
+	{0x3D8A, 0x8070},
+	{0x3D8C, 0x8040},
+	{0x3D8E, 0x4C81},
+	{0x3D90, 0x45C3},
+	{0x3D92, 0x4581},
+	{0x3D94, 0x4C40},
+	{0x3D96, 0x8070},
+	{0x3D98, 0x8040},
+	{0x3D9A, 0x4C85},
+	{0x3D9C, 0x6CA8},
+	{0x3D9E, 0x6C8C},
+	{0x3DA0, 0x000E},
+	{0x3DA2, 0xBE44},
+	{0x3DA4, 0x8844},
+	{0x3DA6, 0xBC78},
+	{0x3DA8, 0x0900},
+	{0x3DAA, 0x8904},
+	{0x3DAC, 0x8080},
+	{0x3DAE, 0x0240},
+	{0x3DB0, 0x8609},
+	{0x3DB2, 0x008E},
+	{0x3DB4, 0x0900},
+	{0x3DB6, 0x8002},
+	{0x3DB8, 0x4080},
+	{0x3DBA, 0x0480},
+	{0x3DBC, 0x887C},
+	{0x3DBE, 0xAA86},
+	{0x3DC0, 0x0900},
+	{0x3DC2, 0x877A},
+	{0x3DC4, 0x000E},
+	{0x3DC6, 0xC379},
+	{0x3DC8, 0x4C40},
+	{0x3DCA, 0xBF70},
+	{0x3DCC, 0x5E40},
+	{0x3DCE, 0x114E},
+	{0x3DD0, 0x5D41},
+	{0x3DD2, 0x5383},
+	{0x3DD4, 0x4200},
+	{0x3DD6, 0xC055},
+	{0x3DD8, 0xA400},
+	{0x3DDA, 0xC083},
+	{0x3DDC, 0x4288},
+	{0x3DDE, 0x6083},
+	{0x3DE0, 0x5B80},
+	{0x3DE2, 0x5A64},
+	{0x3DE4, 0x1030},
+	{0x3DE6, 0x801C},
+	{0x3DE8, 0x00A5},
+	{0x3DEA, 0x5697},
+	{0x3DEC, 0x57A5},
+	{0x3DEE, 0x5180},
+	{0x3DF0, 0x505A},
+	{0x3DF2, 0x814D},
+	{0x3DF4, 0x8358},
+	{0x3DF6, 0x8058},
+	{0x3DF8, 0xA943},
+	{0x3DFA, 0x8345},
+	{0x3DFC, 0xB045},
+	{0x3DFE, 0x8343},
+	{0x3E00, 0xA351},
+	{0x3E02, 0xE251},
+	{0x3E04, 0x8C59},
+	{0x3E06, 0x8059},
+	{0x3E08, 0x8A5F},
+	{0x3E0A, 0xEC7C},
+	{0x3E0C, 0xCC84},
+	{0x3E0E, 0x6182},
+	{0x3E10, 0x6283},
+	{0x3E12, 0x4283},
+	{0x3E14, 0x10CC},
+	{0x3E16, 0x6496},
+	{0x3E18, 0x4281},
+	{0x3E1A, 0x41BB},
+	{0x3E1C, 0x4082},
+	{0x3E1E, 0x407E},
+	{0x3E20, 0xCC41},
+	{0x3E22, 0x8042},
+	{0x3E24, 0x8043},
+	{0x3E26, 0x8300},
+	{0x3E28, 0xC088},
+	{0x3E2A, 0x44BA},
+	{0x3E2C, 0x4488},
+	{0x3E2E, 0x00C8},
+	{0x3E30, 0x8042},
+	{0x3E32, 0x4181},
+	{0x3E34, 0x4082},
+	{0x3E36, 0x4080},
+	{0x3E38, 0x4180},
+	{0x3E3A, 0x4280},
+	{0x3E3C, 0x4383},
+	{0x3E3E, 0x00C0},
+	{0x3E40, 0x8844},
+	{0x3E42, 0xBA44},
+	{0x3E44, 0x8800},
+	{0x3E46, 0xC880},
+	{0x3E48, 0x4241},
+	{0x3E4A, 0x8240},
+	{0x3E4C, 0x8140},
+	{0x3E4E, 0x8041},
+	{0x3E50, 0x8042},
+	{0x3E52, 0x8043},
+	{0x3E54, 0x8300},
+	{0x3E56, 0xC088},
+	{0x3E58, 0x44BA},
+	{0x3E5A, 0x4488},
+	{0x3E5C, 0x00C8},
+	{0x3E5E, 0x8042},
+	{0x3E60, 0x4181},
+	{0x3E62, 0x4082},
+	{0x3E64, 0x4080},
+	{0x3E66, 0x4180},
+	{0x3E68, 0x4280},
+	{0x3E6A, 0x4383},
+	{0x3E6C, 0x00C0},
+	{0x3E6E, 0x8844},
+	{0x3E70, 0xBA44},
+	{0x3E72, 0x8800},
+	{0x3E74, 0xC880},
+	{0x3E76, 0x4241},
+	{0x3E78, 0x8140},
+	{0x3E7A, 0x9F5E},
+	{0x3E7C, 0x8A54},
+	{0x3E7E, 0x8620},
+	{0x3E80, 0x2881},
+	{0x3E82, 0x6026},
+	{0x3E84, 0x8055},
+	{0x3E86, 0x8070},
+	{0x3E88, 0x0000},
+	{0x3E8A, 0x0000},
+	{0x3E8C, 0x0000},
+	{0x3E8E, 0x0000},
+	{0x3E90, 0x0000},
+	{0x3E92, 0x0000},
+	{0x3E94, 0x0000},
+	{0x3E96, 0x0000},
+	{0x3E98, 0x0000},
+	{0x3E9A, 0x0000},
+	{0x3E9C, 0x0000},
+	{0x3E9E, 0x0000},
+	{0x3EA0, 0x0000},
+	{0x3EA2, 0x0000},
+	{0x3EA4, 0x0000},
+	{0x3EA6, 0x0000},
+	{0x3EA8, 0x0000},
+	{0x3EAA, 0x0000},
+	{0x3EAC, 0x0000},
+	{0x3EAE, 0x0000},
+	{0x3EB0, 0x0000},
+	{0x3EB2, 0x0000},
+	{0x3EB4, 0x0000},
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg ar1335_defect_cor[] = {
+	{0x31E0, 0x0781},
+	{0x3F00, 0x004F},
+	{0x3F02, 0x0125},
+	{0x3F04, 0x0020},
+	{0x3F06, 0x0040},
+	{0x3F08, 0x0070},
+	{0x3F0A, 0x0101},
+	{0x3F0C, 0x0302},
+	{0x3F1E, 0x0022},
+	{0x3F1A, 0x01FF},
+	{0x3F14, 0x0101},
+	{0x3F44, 0x0707},
+	{0x3F18, 0x011E},
+	{0x3F12, 0x0303},
+	{0x3F42, 0x1511},
+	{0x3F16, 0x011E},
+	{0x3F10, 0x0505},
+	{0x3F40, 0x1511}, //Enable defect correction
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg ar1335_hdr_on[] = {
+	{0x317A, 0x416E},
+	{0x0400, 0x0000},
+	{0x3EFA, 0x070F},
+	{0x3EFC, 0x070F},
+	{0x31E0, 0x0091},
+	{0x316c, 0x8400},
+	{0x303E, 0x0001},
+	{0x3012, 0x0960},
+	{0x3088, 0x012C},
+	{0x305E, 0x2013},
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg ar1335_hdr_off[] = {
+	{0x3EFA, 0x0F0F},
+	{0x3EFC, 0x0F0F},
+	{0x31E0, 0x0781},
+	{0x316c, 0x8200},
+	{0x303E, 0x0000},
+	{0x305E, 0x2010},
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg ar1335_start_stream[] = {
+	{0x3F3C, 0x0003},
+	{0x301A, 0x023C},
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg ar1335_stop_stream[] = {
+	{0x3F3C, 0x0002},
+	{0x301A, 0x0210},
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg mode_4208x3120_30[] = {
+	{0x31B0, 0x005C},
+	{0x31B2, 0x002D},
+	{0x31B4, 0x2412},
+	{0x31B6, 0x142A},
+	{0x31B8, 0x2413},
+	{0x31BA, 0x1C70},
+	{0x31BC, 0x868B},
+	{0x31AE, 0x0204},
+//These timing are for ar1335_rev1 sensor pll_setup_max
+	{0x0300, 0x0005},
+	{0x0302, 0x0001},
+	{0x0304, 0x0101},
+	{0x0306, 0x2E2E},
+	{0x0308, 0x000A},
+	{0x030A, 0x0001},
+	{0x0112, 0x0A0A},
+	{0x3016, 0x0101},
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+
+	{0x0344, 0x0010},
+	{0x0348, 0x107F},
+	{0x0346, 0x0010},
+	{0x034A, 0x0C3F},
+	{0x034C, 0x1070},
+	{0x034E, 0x0C30},
+	{0x3040, 0x0041},
+	{0x0112, 0x0A0A},
+	{0x0112, 0x0A0A},
+	{0x3172, 0x0206},
+	{0x317A, 0x416E},
+	{0x3F3C, 0x0003},
+	{0x0342, 0x1240},
+	{0x0340, 0x0C4E},
+	{0x0202, 0x0C44},
+
+	{0x3F3C, 0x0003},
+	{0x301A, 0x021C},
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg mode_3840x2160_30[] = {
+	{0x31B0, 0x0086},
+	{0x31B2, 0x0057},
+	{0x31B4, 0x2412},
+	{0x31B6, 0x142A},
+	{0x31B8, 0x2413},
+	{0x31BA, 0x1C70},
+	{0x31BC, 0x068B},// mipi_timing_recommended
+	{0x31AE, 0x0204},
+//These timing are for ar1335_rev1 sensor pll_setup_max
+	{0x0300, 0x0004},
+	{0x0302, 0x0001},
+	{0x0304, 0x0903},
+	{0x0306, 0xCF37},
+	{0x0308, 0x000A},
+	{0x030A, 0x0001},
+	{0x0112, 0x0A0A},
+	{0x3016, 0x0101}, //pll_setup_recommended
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+	{0x0344, 0x00C8},
+	{0x0348, 0x0FC7},
+	{0x0346, 0x01F0},
+	{0x034A, 0x0A5F},
+	{0x034C, 0x0F00},
+	{0x034E, 0x0870},
+	{0x3040, 0x4041},
+	{0x3172, 0x0206},
+	{0x317A, 0x416E},
+	{0x3F3C, 0x0003},
+	{0x0400, 0x0000},
+	{0x0404, 0x0010}, //scalar settings
+	{0x0342, 0x1230},
+	{0x0340, 0x0C4E}, //30 fps
+	{0x0202, 0x0C2E}, //30fps setting
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg mode_1920x1080_60[] = {
+	{0x31B0, 0x005C},
+	{0x31B2, 0x002E},
+	{0x31B4, 0x2412},
+	{0x31B6, 0x142A},
+	{0x31B8, 0x2413},
+	{0x31BA, 0x1C72},
+	{0x31BC, 0x860B},// mipi_timing_recommended
+	{0x3024, 0x0001},
+	{0x31AE, 0x0204},
+	{0x0300, 0x0004},
+	{0x0302, 0x0001},
+	{0x0304, 0x0001},
+	{0x0306, 0x0019},
+	{0x0308, 0x000A},
+	{0x030A, 0x0001},
+	{0x0112, 0x0A0A},
+	{0x3016, 0x0101}, //pll_setup_recommended
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+	{0x0344, 0x00C8},
+	{0x0348, 0x0FC7},
+	{0x0346, 0x01F0},
+	{0x034A, 0x0A5D},
+	{0x034C, 0x0780},
+	{0x034E, 0x0438},
+	{0x3040, 0x0041},
+	{0x3172, 0x0000},
+	{0x317A, 0x0001},
+	{0x3F3C, 0x0000},
+	{0x0400, 0x0001},
+	{0x0404, 0x0020}, //scalar settings
+	{0x0342, 0x18CC},
+	{0x0340, 0x0C2F}, //60 fps
+	{0x0202, 0x0C4E}, //60 fps setting
+
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg mode_1920x1080_30[] = {
+	{0x31B0, 0x004D},
+	{0x31B2, 0x0028},
+	{0x31B4, 0x230E},
+	{0x31B6, 0x1348},
+	{0x31B8, 0x1C12},
+	{0x31BA, 0x185B},
+	{0x31BC, 0x8509},// mipi_timing_recommended
+	{0x31AE, 0x0204},
+	{0x3024, 0x0001},
+//These timing are for ar1335_rev1 sensor pll_setup_max
+	{0x0300, 0x0004},
+	{0x0302, 0x0001},
+	{0x0304, 0x0303},
+	{0x0306, 0x3737},
+	{0x0308, 0x000A},
+	{0x030A, 0x0001},
+	{0x0112, 0x0A0A},
+	{0x3016, 0x0101}, //pll_setup_recommended
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+	{0x0344, 0x00C8},
+	{0x0348, 0x0FC7},
+	{0x0346, 0x01F0},
+	{0x034A, 0x0A5D},
+	{0x034C, 0x0780},
+	{0x034E, 0x0438},
+	{0x3040, 0x4041},
+	{0x3172, 0x0206},
+	{0x317A, 0x516E},
+	{0x3F3C, 0x0003},
+	{0x0400, 0x0001},
+	{0x0404, 0x0020}, //scalar settings
+	{0x0342, 0x1230},
+	{0x0340, 0x0625}, //30 fps
+	{0x0202, 0x0626}, //30fps setting
+	{AR1335_TABLE_END, 0x00}
+};
+
+static struct ar1335_reg mode_1280x720_60[] = {
+	{0x31B0, 0x004D},
+	{0x31B2, 0x0028},
+	{0x31B4, 0x230E},
+	{0x31B6, 0x1348},
+	{0x31B8, 0x1C12},
+	{0x31BA, 0x185B},
+	{0x31BC, 0x8509},// mipi_timing_recommended
+	{0x31AE, 0x0204},
+	{0x3024, 0x0001},
+//These timing are for ar1335_rev1 sensor pll_setup_max
+	{0x0300, 0x0004},
+	{0x0302, 0x0001},
+	{0x0304, 0x0303},
+	{0x0306, 0x3737},
+	{0x0308, 0x000A},
+	{0x030A, 0x0001},
+	{0x0112, 0x0A0A},
+	{0x3016, 0x0101}, //pll_setup_recommended
+	{AR1335_TABLE_WAIT_MS, AR1335_WAIT_MS},
+	{0x0344, 0x00C8},
+	{0x0348, 0x0FC7},
+	{0x0346, 0x01F0},
+	{0x034A, 0x0A5B},
+	{0x034C, 0x0500},
+	{0x034E, 0x02D0},
+	{0x3040, 0x4045},
+	{0x3172, 0x0206},
+	{0x317A, 0x516E},
+	{0x3F3C, 0x0003},
+	{0x0400, 0x0001},
+	{0x0404, 0x0020}, //scalar settings
+	{0x0342, 0x1230},
+	{0x0340, 0x0626}, //30 fps
+	{0x0202, 0x05E8}, //30fps setting
+	{AR1335_TABLE_END, 0x00}
+};
+
+/* Static definitions */
+static struct regmap_config ar1335_reg16_config = {
+	.reg_bits = 16,
+	.val_bits = 16,
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_BIG,
+};
+
+static struct ar1335_res_struct ar1335_res_table[] = {
+	{
+		.width = 1280,
+		.height = 720,
+		.ar1335_mode = mode_1280x720_60,
+	},
+	{
+		.width = 1920,
+		.height = 1080,
+		.ar1335_mode = mode_1920x1080_30,
+	},
+	{
+		.width = 3840,
+		.height = 2160,
+		.ar1335_mode = mode_3840x2160_30,
+	}
+};
+
+static int ar1335_i2c_read_reg(struct v4l2_subdev *sd,
+			       u16 reg, void *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	int ret;
+
+	ret = regmap_read(dev->regmap16, reg, val);
+	if (ret) {
+		dev_info(&client->dev, "Read reg failed. reg=0x%04X\n", reg);
+		return ret;
+	}
+	dev_info(&client->dev, "read_reg[0x%04X] = 0x%04X\n",
+		 reg, *(u16 *)val);
+	return ret;
+}
+
+static int ar1335_i2c_write_reg(struct v4l2_subdev *sd,
+				u16 reg,  u32 val)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret;
+
+	ret = regmap_write(dev->regmap16, reg, val);
+	if (ret) {
+		dev_info(&client->dev, "Write reg failed. reg=0x%04X\n", reg);
+		return ret;
+	}
+	dev_info(&client->dev, "write_reg[0x%04X] = 0x%04X\n", reg, (u16)val);
+	return ret;
+}
+
+static int ar1335_write_table(struct v4l2_subdev *sd,
+			      const struct ar1335_reg table[],
+			      const struct ar1335_reg override_list[],
+			      int num_override_regs)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	const struct ar1335_reg *next;
+	int err, i;
+	u16 val;
+
+	for (next = table; next->addr != AR1335_TABLE_END; next++) {
+		if (next->addr == AR1335_TABLE_WAIT_MS) {
+			msleep(next->val);
+			continue;
+		}
+
+		val = next->val;
+
+		/* When an override list is passed in, replace the reg */
+		/* value to write if the reg is in the list            */
+		if (override_list) {
+			for (i = 0; i < num_override_regs; i++) {
+				if (next->addr == override_list[i].addr) {
+					val = override_list[i].val;
+					break;
+				}
+			}
+		}
+
+		err = ar1335_i2c_write_reg(sd, next->addr, val);
+		if (err) {
+			dev_err(&client->dev, "%s:%d\n", __func__, err);
+			return err;
+		}
+	}
+	return 0;
+}
+
+static int ar1335_enum_mbus_code(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *state,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+	if (code->index) {
+		dev_err(&client->dev, "%s %d\n", __func__, __LINE__);
+		return -EINVAL;
+	}
+
+	code->code = MEDIA_BUS_FMT_SRGGB10_1X10;
+	return 0;
+}
+
+static int ar1335_match_resolution(struct v4l2_mbus_framefmt *fmt)
+{
+	s32 w0, h0, mismatch, distance;
+	s32 w1 = fmt->width;
+	s32 h1 = fmt->height;
+	s32 min_distance = INT_MAX;
+	s32 i, idx = -1;
+
+	if (w1 == 0 || h1 == 0)
+		return -1;
+
+	for (i = 0; i < ARRAY_SIZE(ar1335_res_table); i++) {
+		w0 = ar1335_res_table[i].width;
+		h0 = ar1335_res_table[i].height;
+		if (w0 < w1 || h0 < h1)
+			continue;
+		mismatch = abs(w0 * h1 - w1 * h0) * 8192 / w1 / h0;
+
+		if (mismatch > 8192 * AR1335_MAX_RATIO_MISMATCH / 100)
+			continue;
+		distance = (w0 * h1 + w1 * h0) * 8192 / w1 / h1;
+		if (distance < min_distance) {
+			min_distance = distance;
+			idx = i;
+			break;
+		}
+	}
+
+	return idx;
+}
+
+static s32 ar1335_try_mbus_fmt_locked(struct v4l2_subdev *sd,
+				      struct v4l2_mbus_framefmt *fmt)
+{
+	s32 res_num, idx = -1;
+
+	res_num = ARRAY_SIZE(ar1335_res_table);
+
+	if (fmt->width <= ar1335_res_table[res_num - 1].width &&
+	    fmt->height <= ar1335_res_table[res_num - 1].height)
+		idx = ar1335_match_resolution(fmt);
+	if (idx == -1)
+		idx = res_num - 1;
+
+	fmt->width = ar1335_res_table[idx].width;
+	fmt->height = ar1335_res_table[idx].height;
+
+	return idx;
+}
+
+static int ar1335_get_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_state *state,
+			  struct v4l2_subdev_format *format)
+{
+	struct v4l2_mbus_framefmt *fmt = &format->format;
+	struct ar1335_device *dev = to_ar1335_device(sd);
+
+	if (format->pad)
+		return -EINVAL;
+
+	mutex_lock(&dev->input_lock);
+	fmt->width = dev->format.width;
+	fmt->height = dev->format.height;
+	fmt->code = dev->format.code;
+	fmt->field = dev->format.field;
+	mutex_unlock(&dev->input_lock);
+
+	return 0;
+}
+
+static int ar1335_set_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_state *state,
+			  struct v4l2_subdev_format *format)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	struct v4l2_mbus_framefmt *fmt = &format->format;
+
+	s32 idx, ret = 0;
+
+	mutex_lock(&dev->input_lock);
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		ar1335_try_mbus_fmt_locked(sd, fmt);
+		state->pads->try_fmt = *fmt;
+		mutex_unlock(&dev->input_lock);
+		return 0;
+	}
+	idx = ar1335_try_mbus_fmt_locked(sd, &format->format);
+	dev->cur_res = idx;
+
+	dev->format.width = format->format.width;
+	dev->format.height = format->format.height;
+	dev->format.field = V4L2_FIELD_NONE;
+	if (format->format.code == MEDIA_BUS_FMT_SRGGB10_1X10 ||
+	    format->format.code == MEDIA_BUS_FMT_SRGGB8_1X8) {
+		dev->format.code = format->format.code;
+	} else {
+		dev_err(&client->dev, "%s %d format->format.code %d\n", __func__, __LINE__,
+			format->format.code);
+		return -EINVAL;
+	}
+
+	mutex_unlock(&dev->input_lock);
+	return ret;
+}
+
+static int ar1335_s_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *ival)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	struct v4l2_fract *tpf = &ival->interval;
+
+	if (tpf->numerator == 0 || tpf->denominator == 0 ||
+	    (tpf->denominator > tpf->numerator * MAX_FRAME_RATE)) {
+		/* reset to max frame rate */
+		tpf->numerator = 1;
+		tpf->denominator = MAX_FRAME_RATE;
+	}
+	dev->frame_rate.numerator = tpf->numerator;
+	if (tpf->numerator == 30) {
+		ar1335_i2c_write_reg(sd, 0x340, 0xC4E);
+		ar1335_i2c_write_reg(sd, 0x202, 0xC4E);
+		dev->frame_rate.denominator = tpf->denominator;
+	} else if (tpf->numerator == 60) {
+		ar1335_i2c_write_reg(sd, 0x340, 0x626);
+		ar1335_i2c_write_reg(sd, 0x202, 0x5E8);
+		dev->frame_rate.denominator = tpf->denominator;
+	} else {
+		ar1335_i2c_write_reg(sd, 0x340, 0xC4E);
+		ar1335_i2c_write_reg(sd, 0x202, 0xC4E);
+		dev->frame_rate.denominator = MIN_FRAME_RATE;
+	}
+	return 0;
+}
+
+static int ar1335_g_frame_interval(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_frame_interval *interval)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+
+	mutex_lock(&dev->input_lock);
+	interval->interval.denominator = dev->frame_rate.denominator;
+	interval->interval.numerator = dev->frame_rate.numerator;
+	mutex_unlock(&dev->input_lock);
+	return 0;
+}
+
+static int ar1335_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *state,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	struct ar1335_res_struct *res_table;
+	int index = fse->index;
+
+	mutex_lock(&dev->input_lock);
+	if (index >= dev->cur_res) {
+		mutex_unlock(&dev->input_lock);
+		return -EINVAL;
+	}
+
+	res_table = dev->res_table;
+	fse->min_width = res_table[index].width;
+	fse->min_height = res_table[index].height;
+	fse->max_width = res_table[index].width;
+	fse->max_height = res_table[index].height;
+	mutex_unlock(&dev->input_lock);
+
+	return 0;
+}
+
+static int ar1335_g_skip_frames(struct v4l2_subdev *sd, u32 *frames)
+{
+	*frames = 0;
+	return 0;
+}
+
+static int ar1335_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	u32 idx;
+	int ret;
+
+	mutex_lock(&dev->input_lock);
+	idx = dev->cur_res;
+
+	if (enable) {
+		if (!dev->sys_activated) {
+			ret = ar1335_write_table(sd, ar1335_init, 0, 0);
+			if (ret < 0) {
+				dev_err(&client->dev,
+					"could not sent common table %d\n",
+					ret);
+				goto error;
+			}
+			dev->sys_activated = 1;
+
+			ret = ar1335_write_table(sd,
+						 ar1335_res_table[idx].ar1335_mode,
+						 0, 0);
+			if (ret < 0) {
+				dev_err(&client->dev,
+					"could not sent mode table %d\n", ret);
+				goto error;
+			}
+
+		} else {
+			ret = ar1335_write_table(sd, ar1335_res_table[idx].ar1335_mode,
+						 0, 0);
+			if (ret < 0) {
+				dev_err(&client->dev,
+					"could not sent mode table %d\n", ret);
+				goto error;
+			}
+		}
+
+		ret = ar1335_write_table(sd, ar1335_start_stream, 0, 0);
+		if (ret < 0) {
+			dev_err(&client->dev,
+				"could not sent common table %d\n", ret);
+			goto error;
+		}
+	} else {
+		ret = ar1335_write_table(sd, ar1335_stop_stream, 0, 0);
+		if (ret < 0) {
+			dev_err(&client->dev,
+				"could not sent common table %d\n", ret);
+			goto error;
+		}
+		dev_info(&client->dev, "Stop stream.\n");
+	}
+error:
+	mutex_unlock(&dev->input_lock);
+	return ret;
+}
+
+static u16 ar1335_gain_values[] = { 0x2015, 0x2025, 0x2035,
+				    0x2BBF, 0x573F, 0xAE3F };
+
+static int ar1335_set_gain(struct v4l2_subdev *sd, s32 val)
+{
+	return ar1335_i2c_write_reg(sd, 0x305E, ar1335_gain_values[val]);
+}
+
+static int ar1335_set_hmirror(struct v4l2_subdev *sd, s32 val)
+{
+	int ret = 0;
+	u16 reg_val;
+
+	ret = ar1335_i2c_read_reg(sd, 0x3040, &reg_val);
+	if (ret)
+		return ret;
+
+	if (val == 1)
+		reg_val |= (1 << 14);
+	else
+		reg_val &= ~(1 << 14);
+
+	return ar1335_i2c_write_reg(sd, 0x3040, reg_val);
+}
+
+static int ar1335_set_vflip(struct v4l2_subdev *sd, s32 val)
+{
+	int ret = 0;
+	u16 reg_val;
+
+	ret = ar1335_i2c_read_reg(sd, 0x3040, &reg_val);
+	if (ret)
+		return ret;
+
+	if (val == 1)
+		reg_val |= (1 << 15);
+	else
+		reg_val &= ~(1 << 15);
+
+	return ar1335_i2c_write_reg(sd, 0x3040, reg_val);
+}
+
+static int ar1335_set_line_length_pck(struct v4l2_subdev *sd, s32 val)
+{
+	return ar1335_i2c_write_reg(sd, 0x0342, val);
+}
+
+static int ar1335_set_coarse_integration_time(struct v4l2_subdev *sd, s32 val)
+{
+	return ar1335_i2c_write_reg(sd, 0x0202, val);
+}
+
+static int ar1335_defect_correction(struct v4l2_subdev *sd, s32 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	if (val) {
+		ret = ar1335_write_table(sd, ar1335_defect_cor, 0, 0);
+		if (ret < 0)
+			dev_err(&client->dev,
+				"could not sent common table %d\n", ret);
+	} else {
+		ret = ar1335_i2c_write_reg(sd, 0x31E0, 0x0);
+		if (ret < 0)
+			dev_err(&client->dev,
+				"could not sent common table %d\n", ret);
+	}
+
+	return ret;
+}
+
+static int ar1335_hdr_mode(struct v4l2_subdev *sd, s32 val)
+{
+	int ret = 0;
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+	if (val) {
+		ret = ar1335_write_table(sd, ar1335_hdr_on, 0, 0);
+		if (ret < 0)
+			dev_err(&client->dev,
+				"could not sent common table %d\n", ret);
+	} else {
+		ret = ar1335_write_table(sd, ar1335_hdr_off, 0, 0);
+		if (ret < 0)
+			dev_err(&client->dev,
+				"could not sent common table %d\n", ret);
+	}
+
+	return ret;
+}
+
+static u16 ar1335_test_pattern_values[] = {
+	0x1, // Solid color
+	0x2, // 100% color bar
+	0x3, // fade to gray color
+	0x100, // walking 1 (10bit)
+	0x101, // walking 1 (8bit)
+};
+
+static int ar1335_test_pattern(struct v4l2_subdev *sd, s32 val)
+{
+	return ar1335_i2c_write_reg(sd, 0x0600,
+				    ar1335_test_pattern_values[val]);
+}
+
+static int ar1335_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ar1335_device *dev =
+		container_of(ctrl->handler, struct ar1335_device, ctrl_handler);
+	switch (ctrl->id) {
+	case V4L2_CID_GAIN:
+		ar1335_set_gain(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ar1335_test_pattern(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_VFLIP:
+		ar1335_set_vflip(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_HFLIP:
+		ar1335_set_hmirror(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_HDR_MODE:
+		ar1335_hdr_mode(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_DEFECT_CORRECTION:
+		ar1335_defect_correction(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_LENGTH_LINE_PCK:
+		ar1335_set_line_length_pck(&dev->sd, ctrl->val);
+		break;
+	case V4L2_CID_COARSE_INT_TIME:
+		ar1335_set_coarse_integration_time(&dev->sd, ctrl->val);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int ar1335_g_register(struct v4l2_subdev *sd,
+			     struct v4l2_dbg_register *reg)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	int ret;
+	u32 reg_val;
+
+	mutex_lock(&dev->input_lock);
+	ret = ar1335_i2c_read_reg(sd, reg->reg, &reg_val);
+	mutex_unlock(&dev->input_lock);
+	if (ret)
+		return ret;
+
+	reg->val = reg_val;
+
+	return 0;
+}
+
+static int ar1335_s_register(struct v4l2_subdev *sd,
+			     const struct v4l2_dbg_register *reg)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	int ret;
+
+	mutex_lock(&dev->input_lock);
+	ret = ar1335_i2c_write_reg(sd, reg->reg, reg->val);
+	mutex_unlock(&dev->input_lock);
+	return ret;
+}
+
+static long ar1335_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
+{
+	long ret = 0;
+
+	switch (cmd) {
+	case VIDIOC_DBG_G_REGISTER:
+		ret = ar1335_g_register(sd, arg);
+		break;
+	case VIDIOC_DBG_S_REGISTER:
+		ret = ar1335_s_register(sd, arg);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ctrl_ops = {
+	.s_ctrl = ar1335_s_ctrl,
+};
+
+static const char * const ctrl_run_mode_menu[] = {
+	NULL,
+	"Video",
+	"Still capture",
+	"Continuous capture",
+	"Preview",
+};
+
+static const char * const tp_menu[] = {
+	"Solid color",
+	"100% Color Bar",
+	"Fade-to-Gray Color Bars",
+	"Walking 1s (10-bit)",
+	"Walking 1s (8-bit)",
+};
+
+static const struct v4l2_ctrl_config ctrls[] = {
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_GAIN,
+		.name = "Gain",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 5,
+		.step = 1,
+	},
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_VFLIP,
+		.name = "Vertical flip",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 1,
+		.step = 1,
+	},
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_HFLIP,
+		.name = "Horizontal Mirror",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 1,
+		.step = 1,
+	},
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_HDR_MODE,
+		.name = "HDR Mode",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 1,
+		.step = 1,
+	},
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_DEFECT_CORRECTION,
+		.name = "Defect Correction",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 1,
+		.step = 1,
+	},
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_LENGTH_LINE_PCK,
+		.name = "Line Length Pak",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 0xffff,
+		.step = 1,
+	},
+	{
+		.ops = &ctrl_ops,
+		.id = V4L2_CID_COARSE_INT_TIME,
+		.name = "Coarse integration time",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.def = 0,
+		.max = 0xffff,
+		.step = 1,
+	},
+
+};
+
+static struct v4l2_subdev_sensor_ops ar1335_sensor_ops = {
+	.g_skip_frames = ar1335_g_skip_frames,
+};
+
+static const struct v4l2_subdev_video_ops ar1335_video_ops = {
+	.s_stream = ar1335_s_stream,
+	.s_frame_interval = ar1335_s_frame_interval,
+	.g_frame_interval = ar1335_g_frame_interval,
+};
+
+static const struct v4l2_subdev_core_ops ar1335_core_ops = {
+	.ioctl = ar1335_ioctl,
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+	.g_register = ar1335_g_register,
+	.s_register = ar1335_s_register,
+#endif
+};
+
+static const struct v4l2_subdev_pad_ops ar1335_pad_ops = {
+	.enum_mbus_code = ar1335_enum_mbus_code,
+	.enum_frame_size = ar1335_enum_frame_size,
+	.get_fmt = ar1335_get_fmt,
+	.set_fmt = ar1335_set_fmt,
+};
+
+static const struct v4l2_subdev_ops ar1335_ops = {
+	.core = &ar1335_core_ops,
+	.pad = &ar1335_pad_ops,
+	.video = &ar1335_video_ops,
+	.sensor = &ar1335_sensor_ops
+};
+
+static int ar1335_sw_reset(struct v4l2_subdev *sd)
+{
+	struct ar1335_device *dev = to_ar1335_device(sd);
+	int ret;
+	int val;
+
+	mutex_lock(&dev->input_lock);
+	ret = ar1335_i2c_write_reg(sd, 0x103, 0x100);
+	mdelay(500);
+	ar1335_i2c_read_reg(sd, 0x103, &val);
+	mdelay(500);
+	ar1335_i2c_read_reg(sd, 0x103, &val);
+	mutex_unlock(&dev->input_lock);
+	/* need to wait for 1032 external clocks to
+	 * complete soft standby reset
+	 */
+	return ret;
+}
+
+/* Verify chip ID */
+static int ar1335_identify_module(struct v4l2_subdev *sd)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret;
+	u32 val;
+
+	ret = ar1335_i2c_read_reg(sd, 0x00, &val);
+	if (ret)
+		return ret;
+	if (val != 0x153) {
+		dev_err(&client->dev, "chip id mismatch: 0x153 != %x\n", val);
+		return -ENXIO;
+	}
+
+	ret = ar1335_i2c_read_reg(sd, 0x03, &val);
+	if (ret)
+		return ret;
+
+	if (val != 0x60A) {
+		dev_err(&client->dev, "chip id mismatch: 0x60A != %x\n", val);
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int ar1335_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ar1335_device *dev = to_ar1335_device(sd);
+
+	media_entity_cleanup(&dev->sd.entity);
+	v4l2_device_unregister_subdev(sd);
+
+	return 0;
+}
+
+static int ar1335_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct ar1335_device *dev;
+	int ret;
+	int err;
+	unsigned int i;
+
+	dev_info(&client->dev, "ar1335 probe called.\n");
+
+	/* allocate device & init sub device */
+	dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
+	if (!dev) {
+		dev_err(&client->dev, "%s: failed to allocate memory\n", __func__);
+		return -ENOMEM;
+	}
+
+	mutex_init(&dev->input_lock);
+
+	/* initialize format */
+	dev->format.width = AR1335_DEFAULT_WIDTH;
+	dev->format.height = AR1335_DEFAULT_HEIGHT;
+	dev->format.field = V4L2_FIELD_NONE;
+	dev->format.code = MEDIA_BUS_FMT_SRGGB10_1X10;
+	dev->format.colorspace = V4L2_COLORSPACE_SRGB;
+	dev->frame_rate.numerator = 1;
+	dev->frame_rate.denominator = AR1335_DEF_FRAME_RATE;
+
+	v4l2_i2c_subdev_init(&dev->sd, client, &ar1335_ops);
+
+	dev->regmap16 = devm_regmap_init_i2c(client, &ar1335_reg16_config);
+	if (IS_ERR(dev->regmap16)) {
+		ret = PTR_ERR(dev->regmap16);
+		dev_err(&client->dev,
+			"Failed to allocate 16bit register map: %d\n", ret);
+		return ret;
+	}
+
+	dev->rst_gpio = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(dev->rst_gpio)) {
+		err = PTR_ERR(dev->rst_gpio);
+		if (err == -EPROBE_DEFER)
+			dev_info(&client->dev,
+				 "Probe deferred due to GPIO reset defer\n");
+		else
+			dev_err(&client->dev,
+				"Unable to locate reset property in dt\n");
+	}
+
+	//reset Sensor
+	gpiod_set_value(dev->rst_gpio, 0);
+	mdelay(1);
+	/* hold reset pin low for sufficient clk cycles  */
+	gpiod_set_value(dev->rst_gpio, 1);
+	mdelay(1);
+	/* wait till system reset */
+
+	ret = ar1335_identify_module(&dev->sd);
+	if (ret) {
+		dev_err(&client->dev, "Failed to identity ar1335 sensor: %d\n",
+			ret);
+		ar1335_remove(client);
+		return ret;
+	}
+
+	ret = ar1335_sw_reset(&dev->sd);
+	if (ret) {
+		dev_err(&client->dev,
+			"Failed to do software reset for ar1335 sensor: %d\n",
+			ret);
+		ar1335_remove(client);
+		return ret;
+	}
+
+	dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	dev->pad.flags = MEDIA_PAD_FL_SOURCE;
+	dev->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+
+	ret = v4l2_ctrl_handler_init(&dev->ctrl_handler, ARRAY_SIZE(ctrls));
+	if (ret) {
+		ar1335_remove(client);
+		return ret;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctrls); i++)
+		v4l2_ctrl_new_custom(&dev->ctrl_handler, &ctrls[i], NULL);
+
+	dev->test_pattern = v4l2_ctrl_new_std_menu_items
+		(&dev->ctrl_handler, &ctrl_ops,
+		 V4L2_CID_TEST_PATTERN,
+		 ARRAY_SIZE(tp_menu) - 1, 0, 0, tp_menu);
+
+	if (dev->ctrl_handler.error) {
+		ar1335_remove(client);
+		return dev->ctrl_handler.error;
+	}
+
+	/* Use same lock for controls as for everything else. */
+	dev->ctrl_handler.lock = &dev->input_lock;
+	dev->sd.ctrl_handler = &dev->ctrl_handler;
+
+	ret = media_entity_pads_init(&dev->sd.entity, 1, &dev->pad);
+	if (ret)
+		ar1335_remove(client);
+	ret = v4l2_async_register_subdev(&dev->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register subdev\n");
+		goto out_free;
+	}
+	return ret;
+out_free:
+	v4l2_device_unregister_subdev(&dev->sd);
+	return ret;
+}
+
+static const struct of_device_id ar1335_id[] = {
+	{
+		.compatible =  AR1335_NAME,
+	},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, ar1335_id);
+
+static struct i2c_driver ar1335_driver = {
+	.driver = {
+		.name = AR1335_NAME,
+		.of_match_table = ar1335_id,
+	},
+	.probe = ar1335_probe,
+	.remove = ar1335_remove,
+};
+
+module_i2c_driver(ar1335_driver);
+
+MODULE_AUTHOR("Anil Kumar Mamidala <amamidal@xilinx.com>");
+MODULE_DESCRIPTION("V4L driver for camera sensor AR1335");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ccs/ccs-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ccs/ccs-core.c
@@ -1603,8 +1603,11 @@
 			usleep_range(1000, 2000);
 		} while (--retry);
 
-		if (!reset)
-			return -EIO;
+		if (!reset) {
+			dev_err(dev, "software reset failed\n");
+			rval = -EIO;
+			goto out_cci_addr_fail;
+		}
 	}
 
 	if (sensor->hwcfg.i2c_addr_alt) {
@@ -3086,7 +3089,7 @@
 		try_fmt->code = sensor->internal_csi_format->code;
 		try_fmt->field = V4L2_FIELD_NONE;
 
-		if (ssd != sensor->pixel_array)
+		if (ssd == sensor->pixel_array)
 			continue;
 
 		try_comp = v4l2_subdev_get_try_compose(sd, fh->state, i);
@@ -3649,15 +3652,15 @@
 out_cleanup:
 	ccs_cleanup(sensor);
 
+out_free_ccs_limits:
+	kfree(sensor->ccs_limits);
+
 out_release_mdata:
 	kvfree(sensor->mdata.backing);
 
 out_release_sdata:
 	kvfree(sensor->sdata.backing);
 
-out_free_ccs_limits:
-	kfree(sensor->ccs_limits);
-
 out_power_off:
 	ccs_power_off(&client->dev);
 	mutex_destroy(&sensor->mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ccs/ccs-data.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ccs/ccs-data.c
@@ -10,6 +10,7 @@
 #include <linux/limits.h>
 #include <linux/mm.h>
 #include <linux/slab.h>
+#include <linux/string.h>
 
 #include "ccs-data-defs.h"
 
@@ -97,7 +98,7 @@
 		plen = ((size_t)
 			(__len3->length[0] &
 			 ((1 << CCS_DATA_LENGTH_SPECIFIER_SIZE_SHIFT) - 1))
-			<< 16) + (__len3->length[0] << 8) + __len3->length[1];
+			<< 16) + (__len3->length[1] << 8) + __len3->length[2];
 		break;
 	}
 	default:
@@ -464,8 +465,7 @@
 		rule_payload = __rule_type + 1;
 		rule_plen2 = rule_plen - sizeof(*__rule_type);
 
-		switch (*__rule_type) {
-		case CCS_DATA_BLOCK_RULE_ID_IF: {
+		if (*__rule_type == CCS_DATA_BLOCK_RULE_ID_IF) {
 			const struct __ccs_data_block_rule_if *__if_rules =
 				rule_payload;
 			const size_t __num_if_rules =
@@ -514,49 +514,61 @@
 				rules->if_rules = if_rule;
 				rules->num_if_rules = __num_if_rules;
 			}
-			break;
-		}
-		case CCS_DATA_BLOCK_RULE_ID_READ_ONLY_REGS:
-			rval = ccs_data_parse_reg_rules(bin, &rules->read_only_regs,
-							&rules->num_read_only_regs,
-							rule_payload,
-							rule_payload + rule_plen2,
-							dev);
-			if (rval)
-				return rval;
-			break;
-		case CCS_DATA_BLOCK_RULE_ID_FFD:
-			rval = ccs_data_parse_ffd(bin, &rules->frame_format,
-						  rule_payload,
-						  rule_payload + rule_plen2,
-						  dev);
-			if (rval)
-				return rval;
-			break;
-		case CCS_DATA_BLOCK_RULE_ID_MSR:
-			rval = ccs_data_parse_reg_rules(bin,
-							&rules->manufacturer_regs,
-							&rules->num_manufacturer_regs,
-							rule_payload,
-							rule_payload + rule_plen2,
-							dev);
-			if (rval)
-				return rval;
-			break;
-		case CCS_DATA_BLOCK_RULE_ID_PDAF_READOUT:
-			rval = ccs_data_parse_pdaf_readout(bin,
-							   &rules->pdaf_readout,
-							   rule_payload,
-							   rule_payload + rule_plen2,
-							   dev);
-			if (rval)
-				return rval;
-			break;
-		default:
-			dev_dbg(dev,
-				"Don't know how to handle rule type %u!\n",
-				*__rule_type);
-			return -EINVAL;
+		} else {
+			/* Check there was an if rule before any other rules */
+			if (bin->base && !rules)
+				return -EINVAL;
+
+			switch (*__rule_type) {
+			case CCS_DATA_BLOCK_RULE_ID_READ_ONLY_REGS:
+				rval = ccs_data_parse_reg_rules(bin,
+								rules ?
+								&rules->read_only_regs : NULL,
+								rules ?
+								&rules->num_read_only_regs : NULL,
+								rule_payload,
+								rule_payload + rule_plen2,
+								dev);
+				if (rval)
+					return rval;
+				break;
+			case CCS_DATA_BLOCK_RULE_ID_FFD:
+				rval = ccs_data_parse_ffd(bin, rules ?
+							  &rules->frame_format : NULL,
+							  rule_payload,
+							  rule_payload + rule_plen2,
+							  dev);
+				if (rval)
+					return rval;
+				break;
+			case CCS_DATA_BLOCK_RULE_ID_MSR:
+				rval = ccs_data_parse_reg_rules(bin,
+								rules ?
+								&rules->manufacturer_regs : NULL,
+								rules ?
+								&rules->num_manufacturer_regs : NULL,
+								rule_payload,
+								rule_payload + rule_plen2,
+								dev);
+				if (rval)
+					return rval;
+				break;
+			case CCS_DATA_BLOCK_RULE_ID_PDAF_READOUT:
+				rval = ccs_data_parse_pdaf_readout(bin,
+								   rules ?
+								   &rules->pdaf_readout : NULL,
+								   rule_payload,
+								   rule_payload + rule_plen2,
+								   dev);
+				if (rval)
+					return rval;
+				break;
+			default:
+				dev_dbg(dev,
+					"Don't know how to handle rule type %u!\n",
+					*__rule_type);
+				return -EINVAL;
+			}
 		}
 		__next_rule = __next_rule + rule_hlen + rule_plen;
 	}
@@ -937,15 +949,15 @@
 
 	rval = __ccs_data_parse(&bin, ccsdata, data, len, dev, verbose);
 	if (rval)
-		return rval;
+		goto out_cleanup;
 
 	rval = bin_backing_alloc(&bin);
 	if (rval)
-		return rval;
+		goto out_cleanup;
 
 	rval = __ccs_data_parse(&bin, ccsdata, data, len, dev, false);
 	if (rval)
-		goto out_free;
+		goto out_cleanup;
 
 	if (verbose && ccsdata->version)
 		print_ccs_data_version(dev, ccsdata->version);
@@ -954,15 +966,16 @@
 		rval = -EPROTO;
 		dev_dbg(dev, "parsing mismatch; base %p; now %p; end %p\n",
 			bin.base, bin.now, bin.end);
-		goto out_free;
+		goto out_cleanup;
 	}
 
 	ccsdata->backing = bin.base;
 
 	return 0;
 
-out_free:
+out_cleanup:
 	kvfree(bin.base);
+	memset(ccsdata, 0, sizeof(*ccsdata));
 
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ccs/ccs-quirk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ccs/ccs-quirk.h
@@ -32,12 +32,10 @@
  *		@reg: Pointer to the register to access
  *		@value: Register value, set by the caller on write, or
  *			by the quirk on read
- *
- * @flags: Quirk flags
- *
  *		@return: 0 on success, -ENOIOCTLCMD if no register
  *			 access may be done by the caller (default read
  *			 value is zero), else negative error code on error
+ * @flags: Quirk flags
  */
 struct ccs_quirk {
 	int (*limits)(struct ccs_sensor *sensor);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/et8ek8/et8ek8_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/et8ek8/et8ek8_driver.c
@@ -1460,7 +1460,7 @@
 	return ret;
 }
 
-static int __exit et8ek8_remove(struct i2c_client *client)
+static int et8ek8_remove(struct i2c_client *client)
 {
 	struct v4l2_subdev *subdev = i2c_get_clientdata(client);
 	struct et8ek8_sensor *sensor = to_et8ek8_sensor(subdev);
@@ -1504,7 +1504,7 @@
 		.of_match_table	= et8ek8_of_table,
 	},
 	.probe_new	= et8ek8_probe,
-	.remove		= __exit_p(et8ek8_remove),
+	.remove		= et8ek8_remove,
 	.id_table	= et8ek8_id_table,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/hm11b1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/hm11b1.c
@@ -0,0 +1,1102 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020-2021 Intel Corporation.
+
+#include <asm/unaligned.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/version.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include "power_ctrl_logic.h"
+
+#define HM11B1_LINK_FREQ_384MHZ		384000000ULL
+#define HM11B1_SCLK			72000000LL
+#define HM11B1_MCLK			19200000
+#define HM11B1_DATA_LANES		1
+#define HM11B1_RGB_DEPTH		10
+
+#define HM11B1_REG_CHIP_ID		0x0000
+#define HM11B1_CHIP_ID			0x11B1
+
+#define HM11B1_REG_MODE_SELECT		0x0100
+#define HM11B1_MODE_STANDBY		0x00
+#define HM11B1_MODE_STREAMING		0x01
+
+/* vertical-timings from sensor */
+#define HM11B1_REG_VTS			0x3402
+#define HM11B1_VTS_DEF			0x037d
+#define HM11B1_VTS_MIN			0x0346
+#define HM11B1_VTS_MAX			0xffff
+
+/* horizontal-timings from sensor */
+#define HM11B1_REG_HTS			0x3404
+
+/* Exposure controls from sensor */
+#define HM11B1_REG_EXPOSURE		0x0202
+#define HM11B1_EXPOSURE_MIN		2
+#define HM11B1_EXPOSURE_MAX_MARGIN	2
+#define HM11B1_EXPOSURE_STEP		1
+
+/* Analog gain controls from sensor */
+#define HM11B1_REG_ANALOG_GAIN		0x0205
+#define HM11B1_REG_ANALOG_GAIN_IR	0x0206
+#define HM11B1_ANAL_GAIN_MIN		0
+#define HM11B1_ANAL_GAIN_MAX		0xFF
+#define HM11B1_ANAL_GAIN_STEP		1
+
+/* Digital gain controls from sensor */
+#define HM11B1_REG_DGTL_GAIN		0x0207
+#define HM11B1_REG_DGTL_GAIN_IR		0x0209
+#define HM11B1_DGTL_GAIN_MIN		0x0
+#define HM11B1_DGTL_GAIN_MAX		0x3FF
+#define HM11B1_DGTL_GAIN_STEP		1
+#define HM11B1_DGTL_GAIN_DEFAULT	0x100
+/* register update control */
+#define HM11B1_REG_COMMAND_UPDATE	0x104
+
+/* Test Pattern Control */
+#define HM11B1_REG_TEST_PATTERN		0x0601
+#define HM11B1_TEST_PATTERN_ENABLE	1
+#define HM11B1_TEST_PATTERN_BAR_SHIFT	1
+
+enum {
+	HM11B1_LINK_FREQ_384MHZ_INDEX,
+};
+
+struct hm11b1_reg {
+	u16 address;
+	u8 val;
+};
+
+struct hm11b1_reg_list {
+	u32 num_of_regs;
+	const struct hm11b1_reg *regs;
+};
+
+struct hm11b1_link_freq_config {
+	const struct hm11b1_reg_list reg_list;
+};
+
+struct hm11b1_mode {
+	/* Frame width in pixels */
+	u32 width;
+
+	/* Frame height in pixels */
+	u32 height;
+
+	/* Horizontal timining size */
+	u32 hts;
+
+	/* Default vertical timining size */
+	u32 vts_def;
+
+	/* Min vertical timining size */
+	u32 vts_min;
+
+	/* Link frequency needed for this resolution */
+	u32 link_freq_index;
+
+	/* Sensor register settings for this resolution */
+	const struct hm11b1_reg_list reg_list;
+};
+
+static const struct hm11b1_reg mipi_data_rate_384mbps[] = {
+};
+
+//RAW 10bit 1292x800_30fps_MIPI 384Mbps/lane
+static const struct hm11b1_reg sensor_1292x800_30fps_setting[] = {
+	{0x0103, 0x00},
+	{0x0102, 0x01},
+	{0x0202, 0x03},
+	{0x0203, 0x7C},
+	{0x0205, 0x20},
+	{0x0207, 0x01},
+	{0x0208, 0x00},
+	{0x0209, 0x01},
+	{0x020A, 0x00},
+	{0x0300, 0x91},
+	{0x0301, 0x0A},
+	{0x0302, 0x02},
+	{0x0303, 0x2E},
+	{0x0304, 0x43},
+	{0x0306, 0x00},
+	{0x0307, 0x00},
+	{0x0340, 0x03},
+	{0x0341, 0x60},
+	{0x0342, 0x05},
+	{0x0343, 0xA0},
+	{0x0344, 0x00},
+	{0x0345, 0x00},
+	{0x0346, 0x03},
+	{0x0347, 0x2F},
+	{0x0350, 0xFF},
+	{0x0351, 0x00},
+	{0x0352, 0x00},
+	{0x0370, 0x00},
+	{0x0371, 0x00},
+	{0x0380, 0x00},
+	{0x0381, 0x00},
+	{0x0382, 0x00},
+	{0x1000, 0xC3},
+	{0x1001, 0xD0},
+	{0x100A, 0x13},
+	{0x2000, 0x00},
+	{0x2061, 0x01},
+	{0x2062, 0x00},
+	{0x2063, 0xC8},
+	{0x2100, 0x03},
+	{0x2101, 0xF0},
+	{0x2102, 0xF0},
+	{0x2103, 0x01},
+	{0x2104, 0x10},
+	{0x2105, 0x10},
+	{0x2106, 0x02},
+	{0x2107, 0x0A},
+	{0x2108, 0x10},
+	{0x2109, 0x15},
+	{0x210A, 0x1A},
+	{0x210B, 0x20},
+	{0x210C, 0x08},
+	{0x210D, 0x0A},
+	{0x210E, 0x0F},
+	{0x210F, 0x12},
+	{0x2110, 0x1C},
+	{0x2111, 0x20},
+	{0x2112, 0x23},
+	{0x2113, 0x2A},
+	{0x2114, 0x30},
+	{0x2115, 0x10},
+	{0x2116, 0x00},
+	{0x2117, 0x01},
+	{0x2118, 0x00},
+	{0x2119, 0x06},
+	{0x211A, 0x00},
+	{0x211B, 0x00},
+	{0x2615, 0x08},
+	{0x2616, 0x00},
+	{0x2700, 0x01},
+	{0x2711, 0x01},
+	{0x272F, 0x01},
+	{0x2800, 0x29},
+	{0x2821, 0xCE},
+	{0x2839, 0x27},
+	{0x283A, 0x01},
+	{0x2842, 0x01},
+	{0x2843, 0x00},
+	{0x3022, 0x11},
+	{0x3024, 0x30},
+	{0x3025, 0x12},
+	{0x3026, 0x00},
+	{0x3027, 0x81},
+	{0x3028, 0x01},
+	{0x3029, 0x00},
+	{0x302A, 0x30},
+	{0x3030, 0x00},
+	{0x3032, 0x00},
+	{0x3035, 0x01},
+	{0x303E, 0x00},
+	{0x3051, 0x00},
+	{0x3082, 0x0E},
+	{0x3084, 0x0D},
+	{0x30A8, 0x03},
+	{0x30C4, 0xA0},
+	{0x30D5, 0xC1},
+	{0x30D8, 0x00},
+	{0x30D9, 0x0D},
+	{0x30DB, 0xC2},
+	{0x30DE, 0x25},
+	{0x30E1, 0xC3},
+	{0x30E4, 0x25},
+	{0x30E7, 0xC4},
+	{0x30EA, 0x25},
+	{0x30ED, 0xC5},
+	{0x30F0, 0x25},
+	{0x30F2, 0x0C},
+	{0x30F3, 0x85},
+	{0x30F6, 0x25},
+	{0x30F8, 0x0C},
+	{0x30F9, 0x05},
+	{0x30FB, 0x40},
+	{0x30FC, 0x25},
+	{0x30FD, 0x54},
+	{0x30FE, 0x0C},
+	{0x3100, 0xC2},
+	{0x3103, 0x00},
+	{0x3104, 0x2B},
+	{0x3106, 0xC3},
+	{0x3109, 0x25},
+	{0x310C, 0xC4},
+	{0x310F, 0x25},
+	{0x3112, 0xC5},
+	{0x3115, 0x25},
+	{0x3117, 0x0C},
+	{0x3118, 0x85},
+	{0x311B, 0x25},
+	{0x311D, 0x0C},
+	{0x311E, 0x05},
+	{0x3121, 0x25},
+	{0x3123, 0x0C},
+	{0x3124, 0x0D},
+	{0x3126, 0x40},
+	{0x3127, 0x25},
+	{0x3128, 0x54},
+	{0x3129, 0x0C},
+	{0x3130, 0x20},
+	{0x3134, 0x60},
+	{0x3135, 0xC2},
+	{0x3139, 0x12},
+	{0x313A, 0x07},
+	{0x313F, 0x52},
+	{0x3140, 0x34},
+	{0x3141, 0x2E},
+	{0x314F, 0x07},
+	{0x3151, 0x47},
+	{0x3153, 0xB0},
+	{0x3154, 0x4A},
+	{0x3155, 0xC0},
+	{0x3157, 0x55},
+	{0x3158, 0x01},
+	{0x3165, 0xFF},
+	{0x316B, 0x12},
+	{0x316E, 0x12},
+	{0x3176, 0x12},
+	{0x3178, 0x01},
+	{0x317C, 0x10},
+	{0x317D, 0x05},
+	{0x317F, 0x07},
+	{0x3182, 0x07},
+	{0x3183, 0x11},
+	{0x3184, 0x88},
+	{0x3186, 0x28},
+	{0x3191, 0x00},
+	{0x3192, 0x20},
+	{0x3400, 0x48},
+	{0x3401, 0x00},
+	{0x3402, 0x06},
+	{0x3403, 0xFA},
+	{0x3404, 0x05},
+	{0x3405, 0x40},
+	{0x3406, 0x00},
+	{0x3407, 0x00},
+	{0x3408, 0x03},
+	{0x3409, 0x2F},
+	{0x340A, 0x00},
+	{0x340B, 0x00},
+	{0x340C, 0x00},
+	{0x340D, 0x00},
+	{0x340E, 0x00},
+	{0x340F, 0x00},
+	{0x3410, 0x00},
+	{0x3411, 0x01},
+	{0x3412, 0x00},
+	{0x3413, 0x03},
+	{0x3414, 0xB0},
+	{0x3415, 0x4A},
+	{0x3416, 0xC0},
+	{0x3418, 0x55},
+	{0x3419, 0x03},
+	{0x341B, 0x7D},
+	{0x341C, 0x00},
+	{0x341F, 0x03},
+	{0x3420, 0x00},
+	{0x3421, 0x02},
+	{0x3422, 0x00},
+	{0x3423, 0x02},
+	{0x3424, 0x01},
+	{0x3425, 0x02},
+	{0x3426, 0x00},
+	{0x3427, 0xA2},
+	{0x3428, 0x01},
+	{0x3429, 0x06},
+	{0x342A, 0xF8},
+	{0x3440, 0x01},
+	{0x3441, 0xBE},
+	{0x3442, 0x02},
+	{0x3443, 0x18},
+	{0x3444, 0x03},
+	{0x3445, 0x0C},
+	{0x3446, 0x06},
+	{0x3447, 0x18},
+	{0x3448, 0x09},
+	{0x3449, 0x24},
+	{0x344A, 0x08},
+	{0x344B, 0x08},
+	{0x345C, 0x00},
+	{0x345D, 0x44},
+	{0x345E, 0x02},
+	{0x345F, 0x43},
+	{0x3460, 0x04},
+	{0x3461, 0x3B},
+	{0x3466, 0xF8},
+	{0x3467, 0x43},
+	{0x347D, 0x02},
+	{0x3483, 0x05},
+	{0x3484, 0x0C},
+	{0x3485, 0x03},
+	{0x3486, 0x20},
+	{0x3487, 0x00},
+	{0x3488, 0x00},
+	{0x3489, 0x00},
+	{0x348A, 0x09},
+	{0x348B, 0x00},
+	{0x348C, 0x00},
+	{0x348D, 0x02},
+	{0x348E, 0x01},
+	{0x348F, 0x40},
+	{0x3490, 0x00},
+	{0x3491, 0xC8},
+	{0x3492, 0x00},
+	{0x3493, 0x02},
+	{0x3494, 0x00},
+	{0x3495, 0x02},
+	{0x3496, 0x02},
+	{0x3497, 0x06},
+	{0x3498, 0x05},
+	{0x3499, 0x04},
+	{0x349A, 0x09},
+	{0x349B, 0x05},
+	{0x349C, 0x17},
+	{0x349D, 0x05},
+	{0x349E, 0x00},
+	{0x349F, 0x00},
+	{0x34A0, 0x00},
+	{0x34A1, 0x00},
+	{0x34A2, 0x08},
+	{0x34A3, 0x08},
+	{0x34A4, 0x00},
+	{0x34A5, 0x0B},
+	{0x34A6, 0x0C},
+	{0x34A7, 0x32},
+	{0x34A8, 0x10},
+	{0x34A9, 0xE0},
+	{0x34AA, 0x52},
+	{0x34AB, 0x00},
+	{0x34AC, 0x60},
+	{0x34AD, 0x2B},
+	{0x34AE, 0x25},
+	{0x34AF, 0x48},
+	{0x34B1, 0x06},
+	{0x34B2, 0xF8},
+	{0x34C3, 0xB0},
+	{0x34C4, 0x4A},
+	{0x34C5, 0xC0},
+	{0x34C7, 0x55},
+	{0x34C8, 0x03},
+	{0x34CB, 0x00},
+	{0x353A, 0x00},
+	{0x355E, 0x48},
+	{0x3572, 0xB0},
+	{0x3573, 0x4A},
+	{0x3574, 0xC0},
+	{0x3576, 0x55},
+	{0x3577, 0x03},
+	{0x357A, 0x00},
+	{0x35DA, 0x00},
+	{0x4003, 0x02},
+	{0x4004, 0x02},
+};
+
+static const char * const hm11b1_test_pattern_menu[] = {
+	"Disabled",
+	"Solid Color",
+	"Color Bar",
+	"Color Bar Blending",
+	"PN11",
+};
+
+static const s64 link_freq_menu_items[] = {
+	HM11B1_LINK_FREQ_384MHZ,
+};
+
+static const struct hm11b1_link_freq_config link_freq_configs[] = {
+	[HM11B1_LINK_FREQ_384MHZ_INDEX] = {
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(mipi_data_rate_384mbps),
+			.regs = mipi_data_rate_384mbps,
+		}
+	},
+};
+
+static const struct hm11b1_mode supported_modes[] = {
+	{
+		.width = 1292,
+		.height = 800,
+		.hts = 1344,
+		.vts_def = HM11B1_VTS_DEF,
+		.vts_min = HM11B1_VTS_MIN,
+		.reg_list = {
+			.num_of_regs =
+				ARRAY_SIZE(sensor_1292x800_30fps_setting),
+			.regs = sensor_1292x800_30fps_setting,
+		},
+		.link_freq_index = HM11B1_LINK_FREQ_384MHZ_INDEX,
+	},
+};
+
+struct hm11b1 {
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* V4L2 Controls */
+	struct v4l2_ctrl *link_freq;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *exposure;
+
+	/* Current mode */
+	const struct hm11b1_mode *cur_mode;
+
+	/* To serialize asynchronus callbacks */
+	struct mutex mutex;
+
+	/* Streaming on/off */
+	bool streaming;
+};
+
+static inline struct hm11b1 *to_hm11b1(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct hm11b1, sd);
+}
+
+static u64 to_pixel_rate(u32 f_index)
+{
+	u64 pixel_rate = link_freq_menu_items[f_index] * 2 * HM11B1_DATA_LANES;
+
+	do_div(pixel_rate, HM11B1_RGB_DEPTH);
+
+	return pixel_rate;
+}
+
+static u64 to_pixels_per_line(u32 hts, u32 f_index)
+{
+	u64 ppl = hts * to_pixel_rate(f_index);
+
+	do_div(ppl, HM11B1_SCLK);
+
+	return ppl;
+}
+
+static int hm11b1_read_reg(struct hm11b1 *hm11b1, u16 reg, u16 len, u32 *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	struct i2c_msg msgs[2];
+	u8 addr_buf[2];
+	u8 data_buf[4] = {0};
+	int ret = 0;
+
+	if (len > sizeof(data_buf))
+		return -EINVAL;
+
+	put_unaligned_be16(reg, addr_buf);
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = sizeof(addr_buf);
+	msgs[0].buf = addr_buf;
+	msgs[1].addr = client->addr;
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].len = len;
+	msgs[1].buf = &data_buf[sizeof(data_buf) - len];
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret != ARRAY_SIZE(msgs))
+		return ret < 0 ? ret : -EIO;
+
+	*val = get_unaligned_be32(data_buf);
+
+	return 0;
+}
+
+static int hm11b1_write_reg(struct hm11b1 *hm11b1, u16 reg, u16 len, u32 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	u8 buf[6];
+	int ret = 0;
+
+	if (len > 4)
+		return -EINVAL;
+
+	put_unaligned_be16(reg, buf);
+	put_unaligned_be32(val << 8 * (4 - len), buf + 2);
+
+	ret = i2c_master_send(client, buf, len + 2);
+	if (ret != len + 2)
+		return ret < 0 ? ret : -EIO;
+
+	return 0;
+}
+
+static int hm11b1_write_reg_list(struct hm11b1 *hm11b1,
+				 const struct hm11b1_reg_list *r_list)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	unsigned int i;
+	int ret = 0;
+
+	for (i = 0; i < r_list->num_of_regs; i++) {
+		ret = hm11b1_write_reg(hm11b1, r_list->regs[i].address, 1,
+				       r_list->regs[i].val);
+		if (ret) {
+			dev_err_ratelimited(&client->dev,
+					    "write reg 0x%4.4x return err = %d",
+					    r_list->regs[i].address, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int hm11b1_update_digital_gain(struct hm11b1 *hm11b1, u32 d_gain)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	int ret = 0;
+
+	ret = hm11b1_write_reg(hm11b1, HM11B1_REG_DGTL_GAIN, 2, d_gain);
+	if (ret) {
+		dev_err(&client->dev, "failed to set HM11B1_REG_DGTL_GAIN");
+		return ret;
+	}
+
+	ret = hm11b1_write_reg(hm11b1, HM11B1_REG_DGTL_GAIN_IR, 2, d_gain);
+	if (ret) {
+		dev_err(&client->dev, "failed to set HM11B1_REG_DGTL_GAIN_IR");
+		return ret;
+	}
+
+	return ret;
+}
+
+static int hm11b1_test_pattern(struct hm11b1 *hm11b1, u32 pattern)
+{
+	if (pattern)
+		pattern = pattern << HM11B1_TEST_PATTERN_BAR_SHIFT |
+			  HM11B1_TEST_PATTERN_ENABLE;
+
+	return hm11b1_write_reg(hm11b1, HM11B1_REG_TEST_PATTERN, 1, pattern);
+}
+
+static int hm11b1_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct hm11b1 *hm11b1 = container_of(ctrl->handler,
+					     struct hm11b1, ctrl_handler);
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	s64 exposure_max;
+	int ret = 0;
+
+	/* Propagate change of current control to all related controls */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Update max exposure while meeting expected vblanking */
+		exposure_max = hm11b1->cur_mode->height + ctrl->val -
+			       HM11B1_EXPOSURE_MAX_MARGIN;
+		__v4l2_ctrl_modify_range(hm11b1->exposure,
+					 hm11b1->exposure->minimum,
+					 exposure_max, hm11b1->exposure->step,
+					 exposure_max);
+	}
+
+	/* V4L2 controls values will be applied only when power is already up */
+	if (!pm_runtime_get_if_in_use(&client->dev))
+		return 0;
+
+	ret = hm11b1_write_reg(hm11b1, HM11B1_REG_COMMAND_UPDATE, 1, 1);
+	if (ret) {
+		dev_err(&client->dev, "failed to enable HM11B1_REG_COMMAND_UPDATE");
+		pm_runtime_put(&client->dev);
+		return ret;
+	}
+	switch (ctrl->id) {
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = hm11b1_write_reg(hm11b1, HM11B1_REG_ANALOG_GAIN, 1,
+				       ctrl->val);
+		ret |= hm11b1_write_reg(hm11b1, HM11B1_REG_ANALOG_GAIN_IR, 1,
+					ctrl->val);
+		break;
+
+	case V4L2_CID_DIGITAL_GAIN:
+		ret = hm11b1_update_digital_gain(hm11b1, ctrl->val);
+		break;
+
+	case V4L2_CID_EXPOSURE:
+		/* 4 least significant bits of expsoure are fractional part */
+		ret = hm11b1_write_reg(hm11b1, HM11B1_REG_EXPOSURE, 2,
+				       ctrl->val);
+		break;
+
+	case V4L2_CID_VBLANK:
+		ret = hm11b1_write_reg(hm11b1, HM11B1_REG_VTS, 2,
+				       hm11b1->cur_mode->height + ctrl->val);
+		break;
+
+	case V4L2_CID_TEST_PATTERN:
+		ret = hm11b1_test_pattern(hm11b1, ctrl->val);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	ret |= hm11b1_write_reg(hm11b1, HM11B1_REG_COMMAND_UPDATE, 1, 0);
+	pm_runtime_put(&client->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops hm11b1_ctrl_ops = {
+	.s_ctrl = hm11b1_set_ctrl,
+};
+
+static int hm11b1_init_controls(struct hm11b1 *hm11b1)
+{
+	struct v4l2_ctrl_handler *ctrl_hdlr;
+	const struct hm11b1_mode *cur_mode;
+	s64 exposure_max, h_blank, pixel_rate;
+	u32 vblank_min, vblank_max, vblank_default;
+	int size;
+	int ret = 0;
+
+	ctrl_hdlr = &hm11b1->ctrl_handler;
+	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8);
+	if (ret)
+		return ret;
+
+	ctrl_hdlr->lock = &hm11b1->mutex;
+	cur_mode = hm11b1->cur_mode;
+	size = ARRAY_SIZE(link_freq_menu_items);
+
+	hm11b1->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, &hm11b1_ctrl_ops,
+						   V4L2_CID_LINK_FREQ,
+						   size - 1, 0,
+						   link_freq_menu_items);
+	if (hm11b1->link_freq)
+		hm11b1->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	pixel_rate = to_pixel_rate(HM11B1_LINK_FREQ_384MHZ_INDEX);
+	hm11b1->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &hm11b1_ctrl_ops,
+					       V4L2_CID_PIXEL_RATE, 0,
+					       pixel_rate, 1, pixel_rate);
+
+	vblank_min = cur_mode->vts_min - cur_mode->height;
+	vblank_max = HM11B1_VTS_MAX - cur_mode->height;
+	vblank_default = cur_mode->vts_def - cur_mode->height;
+	hm11b1->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &hm11b1_ctrl_ops,
+					   V4L2_CID_VBLANK, vblank_min,
+					   vblank_max, 1, vblank_default);
+
+	h_blank = to_pixels_per_line(cur_mode->hts, cur_mode->link_freq_index);
+	h_blank -= cur_mode->width;
+	hm11b1->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &hm11b1_ctrl_ops,
+					   V4L2_CID_HBLANK, h_blank, h_blank, 1,
+					   h_blank);
+	if (hm11b1->hblank)
+		hm11b1->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	v4l2_ctrl_new_std(ctrl_hdlr, &hm11b1_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+			  HM11B1_ANAL_GAIN_MIN, HM11B1_ANAL_GAIN_MAX,
+			  HM11B1_ANAL_GAIN_STEP, HM11B1_ANAL_GAIN_MIN);
+	v4l2_ctrl_new_std(ctrl_hdlr, &hm11b1_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+			  HM11B1_DGTL_GAIN_MIN, HM11B1_DGTL_GAIN_MAX,
+			  HM11B1_DGTL_GAIN_STEP, HM11B1_DGTL_GAIN_DEFAULT);
+	exposure_max = cur_mode->vts_def - HM11B1_EXPOSURE_MAX_MARGIN;
+	hm11b1->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &hm11b1_ctrl_ops,
+					     V4L2_CID_EXPOSURE,
+					     HM11B1_EXPOSURE_MIN, exposure_max,
+					     HM11B1_EXPOSURE_STEP,
+					     exposure_max);
+	v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &hm11b1_ctrl_ops,
+				     V4L2_CID_TEST_PATTERN,
+				     ARRAY_SIZE(hm11b1_test_pattern_menu) - 1,
+				     0, 0, hm11b1_test_pattern_menu);
+	if (ctrl_hdlr->error)
+		return ctrl_hdlr->error;
+
+	hm11b1->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+}
+
+static void hm11b1_update_pad_format(const struct hm11b1_mode *mode,
+				     struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+	fmt->field = V4L2_FIELD_NONE;
+}
+
+static int hm11b1_start_streaming(struct hm11b1 *hm11b1)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	const struct hm11b1_reg_list *reg_list;
+	int link_freq_index;
+	int ret = 0;
+
+	power_ctrl_logic_set_power(1);
+	link_freq_index = hm11b1->cur_mode->link_freq_index;
+	reg_list = &link_freq_configs[link_freq_index].reg_list;
+	ret = hm11b1_write_reg_list(hm11b1, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set plls");
+		return ret;
+	}
+
+	reg_list = &hm11b1->cur_mode->reg_list;
+	ret = hm11b1_write_reg_list(hm11b1, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set mode");
+		return ret;
+	}
+
+	ret = __v4l2_ctrl_handler_setup(hm11b1->sd.ctrl_handler);
+	if (ret)
+		return ret;
+
+	ret = hm11b1_write_reg(hm11b1, HM11B1_REG_MODE_SELECT, 1,
+			       HM11B1_MODE_STREAMING);
+	if (ret)
+		dev_err(&client->dev, "failed to start streaming");
+
+	return ret;
+}
+
+static void hm11b1_stop_streaming(struct hm11b1 *hm11b1)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+
+	if (hm11b1_write_reg(hm11b1, HM11B1_REG_MODE_SELECT, 1,
+			     HM11B1_MODE_STANDBY))
+		dev_err(&client->dev, "failed to stop streaming");
+	power_ctrl_logic_set_power(0);
+}
+
+static int hm11b1_set_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	if (hm11b1->streaming == enable)
+		return 0;
+
+	mutex_lock(&hm11b1->mutex);
+	if (enable) {
+		ret = pm_runtime_get_sync(&client->dev);
+		if (ret < 0) {
+			pm_runtime_put_noidle(&client->dev);
+			mutex_unlock(&hm11b1->mutex);
+			return ret;
+		}
+
+		ret = hm11b1_start_streaming(hm11b1);
+		if (ret) {
+			enable = 0;
+			hm11b1_stop_streaming(hm11b1);
+			pm_runtime_put(&client->dev);
+		}
+	} else {
+		hm11b1_stop_streaming(hm11b1);
+		pm_runtime_put(&client->dev);
+	}
+
+	hm11b1->streaming = enable;
+	mutex_unlock(&hm11b1->mutex);
+
+	return ret;
+}
+
+static int __maybe_unused hm11b1_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+
+	mutex_lock(&hm11b1->mutex);
+	if (hm11b1->streaming)
+		hm11b1_stop_streaming(hm11b1);
+
+	mutex_unlock(&hm11b1->mutex);
+
+	return 0;
+}
+
+static int __maybe_unused hm11b1_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+	int ret = 0;
+
+	mutex_lock(&hm11b1->mutex);
+	if (!hm11b1->streaming)
+		goto exit;
+
+	ret = hm11b1_start_streaming(hm11b1);
+	if (ret) {
+		hm11b1->streaming = false;
+		hm11b1_stop_streaming(hm11b1);
+	}
+
+exit:
+	mutex_unlock(&hm11b1->mutex);
+	return ret;
+}
+
+static int hm11b1_set_format(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+	const struct hm11b1_mode *mode;
+	s32 vblank_def, h_blank;
+
+	mode = v4l2_find_nearest_size(supported_modes,
+				      ARRAY_SIZE(supported_modes), width,
+				      height, fmt->format.width,
+				      fmt->format.height);
+
+	mutex_lock(&hm11b1->mutex);
+	hm11b1_update_pad_format(mode, &fmt->format);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
+		*v4l2_subdev_get_try_format(sd, sd_state, fmt->pad) = fmt->format;
+	} else {
+		hm11b1->cur_mode = mode;
+		__v4l2_ctrl_s_ctrl(hm11b1->link_freq, mode->link_freq_index);
+		__v4l2_ctrl_s_ctrl_int64(hm11b1->pixel_rate,
+					 to_pixel_rate(mode->link_freq_index));
+
+		/* Update limits and set FPS to default */
+		vblank_def = mode->vts_def - mode->height;
+		__v4l2_ctrl_modify_range(hm11b1->vblank,
+					 mode->vts_min - mode->height,
+					 HM11B1_VTS_MAX - mode->height, 1,
+					 vblank_def);
+		__v4l2_ctrl_s_ctrl(hm11b1->vblank, vblank_def);
+		h_blank = to_pixels_per_line(mode->hts, mode->link_freq_index) -
+			  mode->width;
+		__v4l2_ctrl_modify_range(hm11b1->hblank, h_blank, h_blank, 1,
+					 h_blank);
+	}
+	mutex_unlock(&hm11b1->mutex);
+
+	return 0;
+}
+
+static int hm11b1_get_format(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+
+	mutex_lock(&hm11b1->mutex);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt->format = *v4l2_subdev_get_try_format(&hm11b1->sd,
+							  sd_state, fmt->pad);
+	else
+		hm11b1_update_pad_format(hm11b1->cur_mode, &fmt->format);
+
+	mutex_unlock(&hm11b1->mutex);
+
+	return 0;
+}
+
+static int hm11b1_enum_mbus_code(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->index > 0)
+		return -EINVAL;
+
+	code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+
+	return 0;
+}
+
+static int hm11b1_enum_frame_size(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->index >= ARRAY_SIZE(supported_modes))
+		return -EINVAL;
+
+	if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
+		return -EINVAL;
+
+	fse->min_width = supported_modes[fse->index].width;
+	fse->max_width = fse->min_width;
+	fse->min_height = supported_modes[fse->index].height;
+	fse->max_height = fse->min_height;
+
+	return 0;
+}
+
+static int hm11b1_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+
+	mutex_lock(&hm11b1->mutex);
+	hm11b1_update_pad_format(&supported_modes[0],
+				 v4l2_subdev_get_try_format(sd, fh->state, 0));
+	mutex_unlock(&hm11b1->mutex);
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops hm11b1_video_ops = {
+	.s_stream = hm11b1_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops hm11b1_pad_ops = {
+	.set_fmt = hm11b1_set_format,
+	.get_fmt = hm11b1_get_format,
+	.enum_mbus_code = hm11b1_enum_mbus_code,
+	.enum_frame_size = hm11b1_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops hm11b1_subdev_ops = {
+	.video = &hm11b1_video_ops,
+	.pad = &hm11b1_pad_ops,
+};
+
+static const struct media_entity_operations hm11b1_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static const struct v4l2_subdev_internal_ops hm11b1_internal_ops = {
+	.open = hm11b1_open,
+};
+
+static int hm11b1_identify_module(struct hm11b1 *hm11b1)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hm11b1->sd);
+	int ret;
+	u32 val;
+
+	ret = hm11b1_read_reg(hm11b1, HM11B1_REG_CHIP_ID, 2, &val);
+	if (ret)
+		return ret;
+
+	if (val != HM11B1_CHIP_ID) {
+		dev_err(&client->dev, "chip id mismatch: %x!=%x",
+			HM11B1_CHIP_ID, val);
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int hm11b1_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hm11b1 *hm11b1 = to_hm11b1(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(sd->ctrl_handler);
+	pm_runtime_disable(&client->dev);
+	mutex_destroy(&hm11b1->mutex);
+
+	return 0;
+}
+
+static int hm11b1_probe(struct i2c_client *client)
+{
+	struct hm11b1 *hm11b1;
+	int ret = 0;
+
+	hm11b1 = devm_kzalloc(&client->dev, sizeof(*hm11b1), GFP_KERNEL);
+	if (!hm11b1)
+		return -ENOMEM;
+
+	v4l2_i2c_subdev_init(&hm11b1->sd, client, &hm11b1_subdev_ops);
+	power_ctrl_logic_set_power(0);
+	power_ctrl_logic_set_power(1);
+	ret = hm11b1_identify_module(hm11b1);
+	if (ret) {
+		dev_err(&client->dev, "failed to find sensor: %d", ret);
+		return ret;
+	}
+
+	mutex_init(&hm11b1->mutex);
+	hm11b1->cur_mode = &supported_modes[0];
+	ret = hm11b1_init_controls(hm11b1);
+	if (ret) {
+		dev_err(&client->dev, "failed to init controls: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	hm11b1->sd.internal_ops = &hm11b1_internal_ops;
+	hm11b1->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	hm11b1->sd.entity.ops = &hm11b1_subdev_entity_ops;
+	hm11b1->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	hm11b1->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&hm11b1->sd.entity, 1, &hm11b1->pad);
+	if (ret) {
+		dev_err(&client->dev, "failed to init entity pads: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ret = v4l2_async_register_subdev_sensor(&hm11b1->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto probe_error_media_entity_cleanup;
+	}
+
+	/*
+	 * Device is already turned on by i2c-core with ACPI domain PM.
+	 * Enable runtime PM and turn off the device.
+	 */
+	pm_runtime_set_active(&client->dev);
+	pm_runtime_enable(&client->dev);
+	pm_runtime_idle(&client->dev);
+
+	power_ctrl_logic_set_power(0);
+	return 0;
+
+probe_error_media_entity_cleanup:
+	media_entity_cleanup(&hm11b1->sd.entity);
+
+probe_error_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(hm11b1->sd.ctrl_handler);
+	mutex_destroy(&hm11b1->mutex);
+
+	return ret;
+}
+
+static const struct dev_pm_ops hm11b1_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(hm11b1_suspend, hm11b1_resume)
+};
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id hm11b1_acpi_ids[] = {
+	{"HIMX11B1"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(acpi, hm11b1_acpi_ids);
+#endif
+
+static struct i2c_driver hm11b1_i2c_driver = {
+	.driver = {
+		.name = "hm11b1",
+		.pm = &hm11b1_pm_ops,
+		.acpi_match_table = ACPI_PTR(hm11b1_acpi_ids),
+	},
+	.probe_new = hm11b1_probe,
+	.remove = hm11b1_remove,
+};
+
+module_i2c_driver(hm11b1_i2c_driver);
+
+MODULE_AUTHOR("Qiu, Tianshu <tian.shu.qiu@intel.com>");
+MODULE_AUTHOR("Shawn Tu <shawnx.tu@intel.com>");
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_AUTHOR("Lai, Jim <jim.lai@intel.com>");
+MODULE_DESCRIPTION("Himax HM11B1 sensor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/imx219.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/imx219.c
@@ -89,6 +89,12 @@
 
 #define IMX219_REG_ORIENTATION		0x0172
 
+/* Binning  Mode */
+#define IMX219_REG_BINNING_MODE		0x0174
+#define IMX219_BINNING_NONE		0x0000
+#define IMX219_BINNING_2X2		0x0101
+#define IMX219_BINNING_2X2_ANALOG	0x0303
+
 /* Test Pattern Control */
 #define IMX219_REG_TEST_PATTERN		0x0600
 #define IMX219_TEST_PATTERN_DISABLE	0
@@ -143,25 +149,66 @@
 
 	/* Default register values */
 	struct imx219_reg_list reg_list;
+
+	/* 2x2 binning is used */
+	bool binning;
 };
 
-/*
- * Register sets lifted off the i2C interface from the Raspberry Pi firmware
- * driver.
- * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
- */
-static const struct imx219_reg mode_3280x2464_regs[] = {
-	{0x0100, 0x00},
+static const struct imx219_reg imx219_common_regs[] = {
+	{0x0100, 0x00},	/* Mode Select */
+
+	/* To Access Addresses 3000-5fff, send the following commands */
 	{0x30eb, 0x0c},
 	{0x30eb, 0x05},
 	{0x300a, 0xff},
 	{0x300b, 0xff},
 	{0x30eb, 0x05},
 	{0x30eb, 0x09},
-	{0x0114, 0x01},
-	{0x0128, 0x00},
-	{0x012a, 0x18},
+
+	/* PLL Clock Table */
+	{0x0301, 0x05},	/* VTPXCK_DIV */
+	{0x0303, 0x01},	/* VTSYSCK_DIV */
+	{0x0304, 0x03},	/* PREPLLCK_VT_DIV 0x03 = AUTO set */
+	{0x0305, 0x03}, /* PREPLLCK_OP_DIV 0x03 = AUTO set */
+	{0x0306, 0x00},	/* PLL_VT_MPY */
+	{0x0307, 0x39},
+	{0x030b, 0x01},	/* OP_SYS_CLK_DIV */
+	{0x030c, 0x00},	/* PLL_OP_MPY */
+	{0x030d, 0x72},
+
+	/* Undocumented registers */
+	{0x455e, 0x00},
+	{0x471e, 0x4b},
+	{0x4767, 0x0f},
+	{0x4750, 0x14},
+	{0x4540, 0x00},
+	{0x47b4, 0x14},
+	{0x4713, 0x30},
+	{0x478b, 0x10},
+	{0x478f, 0x10},
+	{0x4793, 0x10},
+	{0x4797, 0x0e},
+	{0x479b, 0x0e},
+
+	/* Frame Bank Register Group "A" */
+	{0x0162, 0x0d},	/* Line_Length_A */
+	{0x0163, 0x78},
+	{0x0170, 0x01}, /* X_ODD_INC_A */
+	{0x0171, 0x01}, /* Y_ODD_INC_A */
+
+	/* Output setup registers */
+	{0x0114, 0x01},	/* CSI 2-Lane Mode */
+	{0x0128, 0x00},	/* DPHY Auto Mode */
+	{0x012a, 0x18},	/* EXCK_Freq */
 	{0x012b, 0x00},
+};
+
+/*
+ * Register sets lifted off the i2C interface from the Raspberry Pi firmware
+ * driver.
+ * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
+ */
+static const struct imx219_reg mode_3280x2464_regs[] = {
 	{0x0164, 0x00},
 	{0x0165, 0x00},
 	{0x0166, 0x0c},
@@ -174,53 +221,13 @@
 	{0x016d, 0xd0},
 	{0x016e, 0x09},
 	{0x016f, 0xa0},
-	{0x0170, 0x01},
-	{0x0171, 0x01},
-	{0x0174, 0x00},
-	{0x0175, 0x00},
-	{0x0301, 0x05},
-	{0x0303, 0x01},
-	{0x0304, 0x03},
-	{0x0305, 0x03},
-	{0x0306, 0x00},
-	{0x0307, 0x39},
-	{0x030b, 0x01},
-	{0x030c, 0x00},
-	{0x030d, 0x72},
 	{0x0624, 0x0c},
 	{0x0625, 0xd0},
 	{0x0626, 0x09},
 	{0x0627, 0xa0},
-	{0x455e, 0x00},
-	{0x471e, 0x4b},
-	{0x4767, 0x0f},
-	{0x4750, 0x14},
-	{0x4540, 0x00},
-	{0x47b4, 0x14},
-	{0x4713, 0x30},
-	{0x478b, 0x10},
-	{0x478f, 0x10},
-	{0x4793, 0x10},
-	{0x4797, 0x0e},
-	{0x479b, 0x0e},
-	{0x0162, 0x0d},
-	{0x0163, 0x78},
 };
 
 static const struct imx219_reg mode_1920_1080_regs[] = {
-	{0x0100, 0x00},
-	{0x30eb, 0x05},
-	{0x30eb, 0x0c},
-	{0x300a, 0xff},
-	{0x300b, 0xff},
-	{0x30eb, 0x05},
-	{0x30eb, 0x09},
-	{0x0114, 0x01},
-	{0x0128, 0x00},
-	{0x012a, 0x18},
-	{0x012b, 0x00},
-	{0x0162, 0x0d},
-	{0x0163, 0x78},
 	{0x0164, 0x02},
 	{0x0165, 0xa8},
 	{0x0166, 0x0a},
@@ -233,49 +240,13 @@
 	{0x016d, 0x80},
 	{0x016e, 0x04},
 	{0x016f, 0x38},
-	{0x0170, 0x01},
-	{0x0171, 0x01},
-	{0x0174, 0x00},
-	{0x0175, 0x00},
-	{0x0301, 0x05},
-	{0x0303, 0x01},
-	{0x0304, 0x03},
-	{0x0305, 0x03},
-	{0x0306, 0x00},
-	{0x0307, 0x39},
-	{0x030b, 0x01},
-	{0x030c, 0x00},
-	{0x030d, 0x72},
 	{0x0624, 0x07},
 	{0x0625, 0x80},
 	{0x0626, 0x04},
 	{0x0627, 0x38},
-	{0x455e, 0x00},
-	{0x471e, 0x4b},
-	{0x4767, 0x0f},
-	{0x4750, 0x14},
-	{0x4540, 0x00},
-	{0x47b4, 0x14},
-	{0x4713, 0x30},
-	{0x478b, 0x10},
-	{0x478f, 0x10},
-	{0x4793, 0x10},
-	{0x4797, 0x0e},
-	{0x479b, 0x0e},
 };
 
 static const struct imx219_reg mode_1640_1232_regs[] = {
-	{0x0100, 0x00},
-	{0x30eb, 0x0c},
-	{0x30eb, 0x05},
-	{0x300a, 0xff},
-	{0x300b, 0xff},
-	{0x30eb, 0x05},
-	{0x30eb, 0x09},
-	{0x0114, 0x01},
-	{0x0128, 0x00},
-	{0x012a, 0x18},
-	{0x012b, 0x00},
 	{0x0164, 0x00},
 	{0x0165, 0x00},
 	{0x0166, 0x0c},
@@ -288,53 +259,13 @@
 	{0x016d, 0x68},
 	{0x016e, 0x04},
 	{0x016f, 0xd0},
-	{0x0170, 0x01},
-	{0x0171, 0x01},
-	{0x0174, 0x01},
-	{0x0175, 0x01},
-	{0x0301, 0x05},
-	{0x0303, 0x01},
-	{0x0304, 0x03},
-	{0x0305, 0x03},
-	{0x0306, 0x00},
-	{0x0307, 0x39},
-	{0x030b, 0x01},
-	{0x030c, 0x00},
-	{0x030d, 0x72},
 	{0x0624, 0x06},
 	{0x0625, 0x68},
 	{0x0626, 0x04},
 	{0x0627, 0xd0},
-	{0x455e, 0x00},
-	{0x471e, 0x4b},
-	{0x4767, 0x0f},
-	{0x4750, 0x14},
-	{0x4540, 0x00},
-	{0x47b4, 0x14},
-	{0x4713, 0x30},
-	{0x478b, 0x10},
-	{0x478f, 0x10},
-	{0x4793, 0x10},
-	{0x4797, 0x0e},
-	{0x479b, 0x0e},
-	{0x0162, 0x0d},
-	{0x0163, 0x78},
 };
 
 static const struct imx219_reg mode_640_480_regs[] = {
-	{0x0100, 0x00},
-	{0x30eb, 0x05},
-	{0x30eb, 0x0c},
-	{0x300a, 0xff},
-	{0x300b, 0xff},
-	{0x30eb, 0x05},
-	{0x30eb, 0x09},
-	{0x0114, 0x01},
-	{0x0128, 0x00},
-	{0x012a, 0x18},
-	{0x012b, 0x00},
-	{0x0162, 0x0d},
-	{0x0163, 0x78},
 	{0x0164, 0x03},
 	{0x0165, 0xe8},
 	{0x0166, 0x08},
@@ -347,35 +278,10 @@
 	{0x016d, 0x80},
 	{0x016e, 0x01},
 	{0x016f, 0xe0},
-	{0x0170, 0x01},
-	{0x0171, 0x01},
-	{0x0174, 0x03},
-	{0x0175, 0x03},
-	{0x0301, 0x05},
-	{0x0303, 0x01},
-	{0x0304, 0x03},
-	{0x0305, 0x03},
-	{0x0306, 0x00},
-	{0x0307, 0x39},
-	{0x030b, 0x01},
-	{0x030c, 0x00},
-	{0x030d, 0x72},
 	{0x0624, 0x06},
 	{0x0625, 0x68},
 	{0x0626, 0x04},
 	{0x0627, 0xd0},
-	{0x455e, 0x00},
-	{0x471e, 0x4b},
-	{0x4767, 0x0f},
-	{0x4750, 0x14},
-	{0x4540, 0x00},
-	{0x47b4, 0x14},
-	{0x4713, 0x30},
-	{0x478b, 0x10},
-	{0x478f, 0x10},
-	{0x4793, 0x10},
-	{0x4797, 0x0e},
-	{0x479b, 0x0e},
 };
 
 static const struct imx219_reg raw8_framefmt_regs[] = {
@@ -485,6 +391,7 @@
 			.num_of_regs = ARRAY_SIZE(mode_3280x2464_regs),
 			.regs = mode_3280x2464_regs,
 		},
+		.binning = false,
 	},
 	{
 		/* 1080P 30fps cropped */
@@ -501,6 +408,7 @@
 			.num_of_regs = ARRAY_SIZE(mode_1920_1080_regs),
 			.regs = mode_1920_1080_regs,
 		},
+		.binning = false,
 	},
 	{
 		/* 2x2 binned 30fps mode */
@@ -517,6 +425,7 @@
 			.num_of_regs = ARRAY_SIZE(mode_1640_1232_regs),
 			.regs = mode_1640_1232_regs,
 		},
+		.binning = true,
 	},
 	{
 		/* 640x480 30fps mode */
@@ -533,6 +442,7 @@
 			.num_of_regs = ARRAY_SIZE(mode_640_480_regs),
 			.regs = mode_640_480_regs,
 		},
+		.binning = true,
 	},
 };
 
@@ -979,6 +889,35 @@
 	return -EINVAL;
 }
 
+static int imx219_set_binning(struct imx219 *imx219)
+{
+	if (!imx219->mode->binning) {
+		return imx219_write_reg(imx219, IMX219_REG_BINNING_MODE,
+					IMX219_REG_VALUE_16BIT,
+					IMX219_BINNING_NONE);
+	}
+
+	switch (imx219->fmt.code) {
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+		return imx219_write_reg(imx219, IMX219_REG_BINNING_MODE,
+					IMX219_REG_VALUE_16BIT,
+					IMX219_BINNING_2X2_ANALOG);
+
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+		return imx219_write_reg(imx219, IMX219_REG_BINNING_MODE,
+					IMX219_REG_VALUE_16BIT,
+					IMX219_BINNING_2X2);
+	}
+
+	return -EINVAL;
+}
+
 static const struct v4l2_rect *
 __imx219_get_pad_crop(struct imx219 *imx219,
 		      struct v4l2_subdev_state *sd_state,
@@ -1041,6 +980,13 @@
 	if (ret < 0)
 		return ret;
 
+	/* Send all registers that are common to all modes */
+	ret = imx219_write_regs(imx219, imx219_common_regs, ARRAY_SIZE(imx219_common_regs));
+	if (ret) {
+		dev_err(&client->dev, "%s failed to send mfg header\n", __func__);
+		goto err_rpm_put;
+	}
+
 	/* Apply default values of current mode */
 	reg_list = &imx219->mode->reg_list;
 	ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
@@ -1055,6 +1001,13 @@
 			__func__, ret);
 		goto err_rpm_put;
 	}
+
+	ret = imx219_set_binning(imx219);
+	if (ret) {
+		dev_err(&client->dev, "%s failed to set binning: %d\n",
+			__func__, ret);
+		goto err_rpm_put;
+	}
 
 	/* Apply customized values from user */
 	ret =  __v4l2_ctrl_handler_setup(imx219->sd.ctrl_handler);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/imx258.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/imx258.c
@@ -1260,18 +1260,18 @@
 		return -ENOMEM;
 
 	imx258->clk = devm_clk_get_optional(&client->dev, NULL);
+	if (IS_ERR(imx258->clk))
+		return dev_err_probe(&client->dev, PTR_ERR(imx258->clk),
+				     "error getting clock\n");
 	if (!imx258->clk) {
 		dev_dbg(&client->dev,
 			"no clock provided, using clock-frequency property\n");
 
 		device_property_read_u32(&client->dev, "clock-frequency", &val);
-		if (val != IMX258_INPUT_CLOCK_FREQ)
-			return -EINVAL;
-	} else if (IS_ERR(imx258->clk)) {
-		return dev_err_probe(&client->dev, PTR_ERR(imx258->clk),
-				     "error getting clock\n");
+	} else {
+		val = clk_get_rate(imx258->clk);
 	}
-	if (clk_get_rate(imx258->clk) != IMX258_INPUT_CLOCK_FREQ) {
+	if (val != IMX258_INPUT_CLOCK_FREQ) {
 		dev_err(&client->dev, "input clock frequency not supported\n");
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/imx274.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/imx274.c
@@ -1367,6 +1367,10 @@
 	int min, max, def;
 	int ret;
 
+	ret = pm_runtime_resume_and_get(&imx274->client->dev);
+	if (ret < 0)
+		return ret;
+
 	mutex_lock(&imx274->lock);
 	ret = imx274_set_frame_interval(imx274, fi->interval);
 
@@ -1398,6 +1402,7 @@
 
 unlock:
 	mutex_unlock(&imx274->lock);
+	pm_runtime_put(&imx274->client->dev);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/imx335.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/imx335.c
@@ -75,6 +75,12 @@
 	const struct imx335_reg *regs;
 };
 
+static const char * const imx335_supply_name[] = {
+	"avdd", /* Analog (2.9V) supply */
+	"ovdd", /* Digital I/O (1.8V) supply */
+	"dvdd", /* Digital Core (1.2V) supply */
+};
+
 /**
  * struct imx335_mode - imx335 sensor mode structure
  * @width: Frame width
@@ -108,6 +114,7 @@
  * @sd: V4L2 sub-device
  * @pad: Media pad. Only one pad supported
  * @reset_gpio: Sensor reset gpio
+ * @supplies: Regulator supplies to handle power control
  * @inclk: Sensor input clock
  * @ctrl_handler: V4L2 control handler
  * @link_freq_ctrl: Pointer to link frequency control
@@ -127,6 +134,8 @@
 	struct v4l2_subdev sd;
 	struct media_pad pad;
 	struct gpio_desc *reset_gpio;
+	struct regulator_bulk_data supplies[ARRAY_SIZE(imx335_supply_name)];
+
 	struct clk *inclk;
 	struct v4l2_ctrl_handler ctrl_handler;
 	struct v4l2_ctrl *link_freq_ctrl;
@@ -783,13 +792,24 @@
 
 	/* Request optional reset pin */
 	imx335->reset_gpio = devm_gpiod_get_optional(imx335->dev, "reset",
-						     GPIOD_OUT_LOW);
+						     GPIOD_OUT_HIGH);
 	if (IS_ERR(imx335->reset_gpio)) {
 		dev_err(imx335->dev, "failed to get reset gpio %ld",
 			PTR_ERR(imx335->reset_gpio));
 		return PTR_ERR(imx335->reset_gpio);
 	}
 
+	for (i = 0; i < ARRAY_SIZE(imx335_supply_name); i++)
+		imx335->supplies[i].supply = imx335_supply_name[i];
+
+	ret = devm_regulator_bulk_get(imx335->dev,
+				      ARRAY_SIZE(imx335_supply_name),
+				      imx335->supplies);
+	if (ret) {
+		dev_err(imx335->dev, "Failed to get regulators\n");
+		return ret;
+	}
+
 	/* Get sensor input clock */
 	imx335->inclk = devm_clk_get(imx335->dev, NULL);
 	if (IS_ERR(imx335->inclk)) {
@@ -868,7 +888,17 @@
 	struct imx335 *imx335 = to_imx335(sd);
 	int ret;
 
-	gpiod_set_value_cansleep(imx335->reset_gpio, 1);
+	ret = regulator_bulk_enable(ARRAY_SIZE(imx335_supply_name),
+				    imx335->supplies);
+	if (ret) {
+		dev_err(dev, "%s: failed to enable regulators\n",
+			__func__);
+		return ret;
+	}
+
+	usleep_range(500, 550); /* Tlow */
+
+	gpiod_set_value_cansleep(imx335->reset_gpio, 0);
 
 	ret = clk_prepare_enable(imx335->inclk);
 	if (ret) {
@@ -876,12 +906,13 @@
 		goto error_reset;
 	}
 
-	usleep_range(20, 22);
+	usleep_range(20, 22); /* T4 */
 
 	return 0;
 
 error_reset:
-	gpiod_set_value_cansleep(imx335->reset_gpio, 0);
+	gpiod_set_value_cansleep(imx335->reset_gpio, 1);
+	regulator_bulk_disable(ARRAY_SIZE(imx335_supply_name), imx335->supplies);
 
 	return ret;
 }
@@ -897,9 +928,9 @@
 	struct v4l2_subdev *sd = dev_get_drvdata(dev);
 	struct imx335 *imx335 = to_imx335(sd);
 
-	gpiod_set_value_cansleep(imx335->reset_gpio, 0);
-
+	gpiod_set_value_cansleep(imx335->reset_gpio, 1);
 	clk_disable_unprepare(imx335->inclk);
+	regulator_bulk_disable(ARRAY_SIZE(imx335_supply_name), imx335->supplies);
 
 	return 0;
 }
@@ -971,8 +1002,8 @@
 	imx335->hblank_ctrl = v4l2_ctrl_new_std(ctrl_hdlr,
 						&imx335_ctrl_ops,
 						V4L2_CID_HBLANK,
-						IMX335_REG_MIN,
-						IMX335_REG_MAX,
+						mode->hblank,
+						mode->hblank,
 						1, mode->hblank);
 	if (imx335->hblank_ctrl)
 		imx335->hblank_ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/imx355.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/imx355.c
@@ -1784,10 +1784,6 @@
 		goto error_handler_free;
 	}
 
-	ret = v4l2_async_register_subdev_sensor(&imx355->sd);
-	if (ret < 0)
-		goto error_media_entity;
-
 	/*
 	 * Device is already turned on by i2c-core with ACPI domain PM.
 	 * Enable runtime PM and turn off the device.
@@ -1796,9 +1792,15 @@
 	pm_runtime_enable(&client->dev);
 	pm_runtime_idle(&client->dev);
 
+	ret = v4l2_async_register_subdev_sensor(&imx355->sd);
+	if (ret < 0)
+		goto error_media_entity_runtime_pm;
+
 	return 0;
 
-error_media_entity:
+error_media_entity_runtime_pm:
+	pm_runtime_disable(&client->dev);
+	pm_runtime_set_suspended(&client->dev);
 	media_entity_cleanup(&imx355->sd.entity);
 
 error_handler_free:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/imx412.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/imx412.c
@@ -535,14 +535,13 @@
  */
 static int imx412_update_exp_gain(struct imx412 *imx412, u32 exposure, u32 gain)
 {
-	u32 lpfr, shutter;
+	u32 lpfr;
 	int ret;
 
 	lpfr = imx412->vblank + imx412->cur_mode->height;
-	shutter = lpfr - exposure;
 
-	dev_dbg(imx412->dev, "Set exp %u, analog gain %u, shutter %u, lpfr %u",
-		exposure, gain, shutter, lpfr);
+	dev_dbg(imx412->dev, "Set exp %u, analog gain %u, lpfr %u\n",
+		exposure, gain, lpfr);
 
 	ret = imx412_write_reg(imx412, IMX412_REG_HOLD, 1, 1);
 	if (ret)
@@ -552,7 +551,7 @@
 	if (ret)
 		goto error_release_group_hold;
 
-	ret = imx412_write_reg(imx412, IMX412_REG_EXPOSURE_CIT, 2, shutter);
+	ret = imx412_write_reg(imx412, IMX412_REG_EXPOSURE_CIT, 2, exposure);
 	if (ret)
 		goto error_release_group_hold;
 
@@ -588,7 +587,7 @@
 	case V4L2_CID_VBLANK:
 		imx412->vblank = imx412->vblank_ctrl->val;
 
-		dev_dbg(imx412->dev, "Received vblank %u, new lpfr %u",
+		dev_dbg(imx412->dev, "Received vblank %u, new lpfr %u\n",
 			imx412->vblank,
 			imx412->vblank + imx412->cur_mode->height);
 
@@ -607,7 +606,7 @@
 		exposure = ctrl->val;
 		analog_gain = imx412->again_ctrl->val;
 
-		dev_dbg(imx412->dev, "Received exp %u, analog gain %u",
+		dev_dbg(imx412->dev, "Received exp %u, analog gain %u\n",
 			exposure, analog_gain);
 
 		ret = imx412_update_exp_gain(imx412, exposure, analog_gain);
@@ -616,7 +615,7 @@
 
 		break;
 	default:
-		dev_err(imx412->dev, "Invalid control %d", ctrl->id);
+		dev_err(imx412->dev, "Invalid control %d\n", ctrl->id);
 		ret = -EINVAL;
 	}
 
@@ -797,14 +796,14 @@
 	ret = imx412_write_regs(imx412, reg_list->regs,
 				reg_list->num_of_regs);
 	if (ret) {
-		dev_err(imx412->dev, "fail to write initial registers");
+		dev_err(imx412->dev, "fail to write initial registers\n");
 		return ret;
 	}
 
 	/* Setup handler will write actual exposure and gain */
 	ret =  __v4l2_ctrl_handler_setup(imx412->sd.ctrl_handler);
 	if (ret) {
-		dev_err(imx412->dev, "fail to setup handler");
+		dev_err(imx412->dev, "fail to setup handler\n");
 		return ret;
 	}
 
@@ -815,7 +814,7 @@
 	ret = imx412_write_reg(imx412, IMX412_REG_MODE_SELECT,
 			       1, IMX412_MODE_STREAMING);
 	if (ret) {
-		dev_err(imx412->dev, "fail to start streaming");
+		dev_err(imx412->dev, "fail to start streaming\n");
 		return ret;
 	}
 
@@ -896,7 +895,7 @@
 		return ret;
 
 	if (val != IMX412_ID) {
-		dev_err(imx412->dev, "chip id mismatch: %x!=%x",
+		dev_err(imx412->dev, "chip id mismatch: %x!=%x\n",
 			IMX412_ID, val);
 		return -ENXIO;
 	}
@@ -928,7 +927,7 @@
 	imx412->reset_gpio = devm_gpiod_get_optional(imx412->dev, "reset",
 						     GPIOD_OUT_LOW);
 	if (IS_ERR(imx412->reset_gpio)) {
-		dev_err(imx412->dev, "failed to get reset gpio %ld",
+		dev_err(imx412->dev, "failed to get reset gpio %ld\n",
 			PTR_ERR(imx412->reset_gpio));
 		return PTR_ERR(imx412->reset_gpio);
 	}
@@ -936,13 +935,13 @@
 	/* Get sensor input clock */
 	imx412->inclk = devm_clk_get(imx412->dev, NULL);
 	if (IS_ERR(imx412->inclk)) {
-		dev_err(imx412->dev, "could not get inclk");
+		dev_err(imx412->dev, "could not get inclk\n");
 		return PTR_ERR(imx412->inclk);
 	}
 
 	rate = clk_get_rate(imx412->inclk);
 	if (rate != IMX412_INCLK_RATE) {
-		dev_err(imx412->dev, "inclk frequency mismatch");
+		dev_err(imx412->dev, "inclk frequency mismatch\n");
 		return -EINVAL;
 	}
 
@@ -957,14 +956,14 @@
 
 	if (bus_cfg.bus.mipi_csi2.num_data_lanes != IMX412_NUM_DATA_LANES) {
 		dev_err(imx412->dev,
-			"number of CSI2 data lanes %d is not supported",
+			"number of CSI2 data lanes %d is not supported\n",
 			bus_cfg.bus.mipi_csi2.num_data_lanes);
 		ret = -EINVAL;
 		goto done_endpoint_free;
 	}
 
 	if (!bus_cfg.nr_of_link_frequencies) {
-		dev_err(imx412->dev, "no link frequencies defined");
+		dev_err(imx412->dev, "no link frequencies defined\n");
 		ret = -EINVAL;
 		goto done_endpoint_free;
 	}
@@ -1011,11 +1010,11 @@
 	struct imx412 *imx412 = to_imx412(sd);
 	int ret;
 
-	gpiod_set_value_cansleep(imx412->reset_gpio, 1);
+	gpiod_set_value_cansleep(imx412->reset_gpio, 0);
 
 	ret = clk_prepare_enable(imx412->inclk);
 	if (ret) {
-		dev_err(imx412->dev, "fail to enable inclk");
+		dev_err(imx412->dev, "fail to enable inclk\n");
 		goto error_reset;
 	}
 
@@ -1024,7 +1023,7 @@
 	return 0;
 
 error_reset:
-	gpiod_set_value_cansleep(imx412->reset_gpio, 0);
+	gpiod_set_value_cansleep(imx412->reset_gpio, 1);
 
 	return ret;
 }
@@ -1040,10 +1039,10 @@
 	struct v4l2_subdev *sd = dev_get_drvdata(dev);
 	struct imx412 *imx412 = to_imx412(sd);
 
-	gpiod_set_value_cansleep(imx412->reset_gpio, 0);
-
 	clk_disable_unprepare(imx412->inclk);
 
+	gpiod_set_value_cansleep(imx412->reset_gpio, 1);
+
 	return 0;
 }
 
@@ -1121,7 +1120,7 @@
 		imx412->hblank_ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
 
 	if (ctrl_hdlr->error) {
-		dev_err(imx412->dev, "control init failed: %d",
+		dev_err(imx412->dev, "control init failed: %d\n",
 			ctrl_hdlr->error);
 		v4l2_ctrl_handler_free(ctrl_hdlr);
 		return ctrl_hdlr->error;
@@ -1154,7 +1153,7 @@
 
 	ret = imx412_parse_hw_config(imx412);
 	if (ret) {
-		dev_err(imx412->dev, "HW configuration is not supported");
+		dev_err(imx412->dev, "HW configuration is not supported\n");
 		return ret;
 	}
 
@@ -1162,14 +1161,14 @@
 
 	ret = imx412_power_on(imx412->dev);
 	if (ret) {
-		dev_err(imx412->dev, "failed to power-on the sensor");
+		dev_err(imx412->dev, "failed to power-on the sensor\n");
 		goto error_mutex_destroy;
 	}
 
 	/* Check module identity */
 	ret = imx412_detect(imx412);
 	if (ret) {
-		dev_err(imx412->dev, "failed to find sensor: %d", ret);
+		dev_err(imx412->dev, "failed to find sensor: %d\n", ret);
 		goto error_power_off;
 	}
 
@@ -1179,7 +1178,7 @@
 
 	ret = imx412_init_controls(imx412);
 	if (ret) {
-		dev_err(imx412->dev, "failed to init controls: %d", ret);
+		dev_err(imx412->dev, "failed to init controls: %d\n", ret);
 		goto error_power_off;
 	}
 
@@ -1191,14 +1190,14 @@
 	imx412->pad.flags = MEDIA_PAD_FL_SOURCE;
 	ret = media_entity_pads_init(&imx412->sd.entity, 1, &imx412->pad);
 	if (ret) {
-		dev_err(imx412->dev, "failed to init entity pads: %d", ret);
+		dev_err(imx412->dev, "failed to init entity pads: %d\n", ret);
 		goto error_handler_free;
 	}
 
 	ret = v4l2_async_register_subdev_sensor(&imx412->sd);
 	if (ret < 0) {
 		dev_err(imx412->dev,
-			"failed to register async subdev: %d", ret);
+			"failed to register async subdev: %d\n", ret);
 		goto error_media_entity;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ir-kbd-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ir-kbd-i2c.c
@@ -791,6 +791,7 @@
 		rc_proto    = RC_PROTO_BIT_RC5 | RC_PROTO_BIT_RC6_MCE |
 							RC_PROTO_BIT_RC6_6A_32;
 		ir_codes    = RC_MAP_HAUPPAUGE;
+		ir->polling_interval = 125;
 		probe_tx = true;
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/m5mols/m5mols_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/m5mols/m5mols_core.c
@@ -488,7 +488,7 @@
 	do {
 		if (code == m5mols_default_ffmt[type].code)
 			return type;
-	} while (type++ != SIZE_DEFAULT_FFMT);
+	} while (++type != SIZE_DEFAULT_FFMT);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/max9286.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/max9286.c
@@ -15,6 +15,7 @@
 #include <linux/fwnode.h>
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/driver.h>
+#include <linux/gpio/machine.h>
 #include <linux/i2c.h>
 #include <linux/i2c-mux.h>
 #include <linux/module.h>
@@ -168,6 +169,8 @@
 	u32 init_rev_chan_mv;
 	u32 rev_chan_mv;
 
+	u32 gpio_poc[2];
+
 	struct v4l2_ctrl_handler ctrls;
 	struct v4l2_ctrl *pixelrate;
 
@@ -925,6 +928,7 @@
 err_put_node:
 	fwnode_handle_put(ep);
 err_async:
+	v4l2_ctrl_handler_free(&priv->ctrls);
 	max9286_v4l2_notifier_unregister(priv);
 
 	return ret;
@@ -933,6 +937,7 @@
 static void max9286_v4l2_unregister(struct max9286_priv *priv)
 {
 	fwnode_handle_put(priv->sd.fwnode);
+	v4l2_ctrl_handler_free(&priv->ctrls);
 	v4l2_async_unregister_subdev(&priv->sd);
 	max9286_v4l2_notifier_unregister(priv);
 }
@@ -1026,20 +1031,27 @@
 	return 0;
 }
 
-static void max9286_gpio_set(struct gpio_chip *chip,
-			     unsigned int offset, int value)
+static int max9286_gpio_set(struct max9286_priv *priv, unsigned int offset,
+			    int value)
 {
-	struct max9286_priv *priv = gpiochip_get_data(chip);
-
 	if (value)
 		priv->gpio_state |= BIT(offset);
 	else
 		priv->gpio_state &= ~BIT(offset);
 
-	max9286_write(priv, 0x0f, MAX9286_0X0F_RESERVED | priv->gpio_state);
+	return max9286_write(priv, 0x0f,
+			     MAX9286_0X0F_RESERVED | priv->gpio_state);
+}
+
+static void max9286_gpiochip_set(struct gpio_chip *chip,
+				 unsigned int offset, int value)
+{
+	struct max9286_priv *priv = gpiochip_get_data(chip);
+
+	max9286_gpio_set(priv, offset, value);
 }
 
-static int max9286_gpio_get(struct gpio_chip *chip, unsigned int offset)
+static int max9286_gpiochip_get(struct gpio_chip *chip, unsigned int offset)
 {
 	struct max9286_priv *priv = gpiochip_get_data(chip);
 
@@ -1059,13 +1071,10 @@
 	gpio->of_node = dev->of_node;
 	gpio->ngpio = 2;
 	gpio->base = -1;
-	gpio->set = max9286_gpio_set;
-	gpio->get = max9286_gpio_get;
+	gpio->set = max9286_gpiochip_set;
+	gpio->get = max9286_gpiochip_get;
 	gpio->can_sleep = true;
 
-	/* GPIO values default to high */
-	priv->gpio_state = BIT(0) | BIT(1);
-
 	ret = devm_gpiochip_add_data(dev, gpio, priv);
 	if (ret)
 		dev_err(dev, "Unable to create gpio_chip\n");
@@ -1073,26 +1082,83 @@
 	return ret;
 }
 
-static int max9286_init(struct device *dev)
+static int max9286_parse_gpios(struct max9286_priv *priv)
 {
-	struct max9286_priv *priv;
-	struct i2c_client *client;
+	struct device *dev = &priv->client->dev;
 	int ret;
 
-	client = to_i2c_client(dev);
-	priv = i2c_get_clientdata(client);
+	/* GPIO values default to high */
+	priv->gpio_state = BIT(0) | BIT(1);
 
-	/* Enable the bus power. */
-	ret = regulator_enable(priv->regulator);
-	if (ret < 0) {
-		dev_err(&client->dev, "Unable to turn PoC on\n");
-		return ret;
+	/*
+	 * Parse the "gpio-poc" vendor property. If the property is not
+	 * specified the camera power is controlled by a regulator.
+	 */
+	ret = of_property_read_u32_array(dev->of_node, "maxim,gpio-poc",
+					 priv->gpio_poc, 2);
+	if (ret == -EINVAL) {
+		/*
+		 * If gpio lines are not used for the camera power, register
+		 * a gpio controller for consumers.
+		 */
+		ret = max9286_register_gpio(priv);
+		if (ret)
+			return ret;
+
+		priv->regulator = devm_regulator_get(dev, "poc");
+		if (IS_ERR(priv->regulator)) {
+			return dev_err_probe(dev, PTR_ERR(priv->regulator),
+					     "Unable to get PoC regulator (%ld)\n",
+					     PTR_ERR(priv->regulator));
+		}
+
+		return 0;
+	}
+
+	/* If the property is specified make sure it is well formed. */
+	if (ret || priv->gpio_poc[0] > 1 ||
+	    (priv->gpio_poc[1] != GPIO_ACTIVE_HIGH &&
+	     priv->gpio_poc[1] != GPIO_ACTIVE_LOW)) {
+		dev_err(dev, "Invalid 'gpio-poc' property\n");
+		return -EINVAL;
 	}
 
+	return 0;
+}
+
+static int max9286_poc_enable(struct max9286_priv *priv, bool enable)
+{
+	int ret;
+
+	/* If the regulator is not available, use gpio to control power. */
+	if (!priv->regulator)
+		ret = max9286_gpio_set(priv, priv->gpio_poc[0],
+				       enable ^ priv->gpio_poc[1]);
+	else if (enable)
+		ret = regulator_enable(priv->regulator);
+	else
+		ret = regulator_disable(priv->regulator);
+
+	if (ret < 0)
+		dev_err(&priv->client->dev, "Unable to turn power %s\n",
+			enable ? "on" : "off");
+
+	return ret;
+}
+
+static int max9286_init(struct max9286_priv *priv)
+{
+	struct i2c_client *client = priv->client;
+	int ret;
+
+	ret = max9286_poc_enable(priv, true);
+	if (ret)
+		return ret;
+
 	ret = max9286_setup(priv);
 	if (ret) {
-		dev_err(dev, "Unable to setup max9286\n");
-		goto err_regulator;
+		dev_err(&client->dev, "Unable to setup max9286\n");
+		goto err_poc_disable;
 	}
 
 	/*
@@ -1101,13 +1167,13 @@
 	 */
 	ret = max9286_v4l2_register(priv);
 	if (ret) {
-		dev_err(dev, "Failed to register with V4L2\n");
-		goto err_regulator;
+		dev_err(&client->dev, "Failed to register with V4L2\n");
+		goto err_poc_disable;
 	}
 
 	ret = max9286_i2c_mux_init(priv);
 	if (ret) {
-		dev_err(dev, "Unable to initialize I2C multiplexer\n");
+		dev_err(&client->dev, "Unable to initialize I2C multiplexer\n");
 		goto err_v4l2_register;
 	}
 
@@ -1118,8 +1184,8 @@
 
 err_v4l2_register:
 	max9286_v4l2_unregister(priv);
-err_regulator:
-	regulator_disable(priv->regulator);
+err_poc_disable:
+	max9286_poc_enable(priv, false);
 
 	return ret;
 }
@@ -1165,7 +1231,6 @@
 
 		i2c_mux_mask |= BIT(id);
 	}
-	of_node_put(node);
 	of_node_put(i2c_mux);
 
 	/* Parse the endpoints */
@@ -1229,7 +1294,6 @@
 		priv->source_mask |= BIT(ep.port);
 		priv->nsources++;
 	}
-	of_node_put(node);
 
 	/*
 	 * Parse the initial value of the reverse channel amplitude from
@@ -1262,7 +1326,6 @@
 	mutex_init(&priv->mutex);
 
 	priv->client = client;
-	i2c_set_clientdata(client, priv);
 
 	priv->gpiod_pwdn = devm_gpiod_get_optional(&client->dev, "enable",
 						   GPIOD_OUT_HIGH);
@@ -1290,25 +1353,15 @@
 	 */
 	max9286_configure_i2c(priv, false);
 
-	ret = max9286_register_gpio(priv);
+	ret = max9286_parse_gpios(priv);
 	if (ret)
 		goto err_powerdown;
 
-	priv->regulator = devm_regulator_get(&client->dev, "poc");
-	if (IS_ERR(priv->regulator)) {
-		if (PTR_ERR(priv->regulator) != -EPROBE_DEFER)
-			dev_err(&client->dev,
-				"Unable to get PoC regulator (%ld)\n",
-				PTR_ERR(priv->regulator));
-		ret = PTR_ERR(priv->regulator);
-		goto err_powerdown;
-	}
-
 	ret = max9286_parse_dt(priv);
 	if (ret)
 		goto err_powerdown;
 
-	ret = max9286_init(&client->dev);
+	ret = max9286_init(priv);
 	if (ret < 0)
 		goto err_cleanup_dt;
 
@@ -1324,13 +1377,13 @@
 
 static int max9286_remove(struct i2c_client *client)
 {
-	struct max9286_priv *priv = i2c_get_clientdata(client);
+	struct max9286_priv *priv = sd_to_max9286(i2c_get_clientdata(client));
 
 	i2c_mux_del_adapters(priv->mux);
 
 	max9286_v4l2_unregister(priv);
 
-	regulator_disable(priv->regulator);
+	max9286_poc_enable(priv, false);
 
 	gpiod_set_value_cansleep(priv->gpiod_pwdn, 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/mt9p031.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/mt9p031.c
@@ -78,7 +78,9 @@
 #define		MT9P031_PIXEL_CLOCK_INVERT		(1 << 15)
 #define		MT9P031_PIXEL_CLOCK_SHIFT(n)		((n) << 8)
 #define		MT9P031_PIXEL_CLOCK_DIVIDE(n)		((n) << 0)
-#define MT9P031_FRAME_RESTART				0x0b
+#define MT9P031_RESTART					0x0b
+#define		MT9P031_FRAME_PAUSE_RESTART		(1 << 1)
+#define		MT9P031_FRAME_RESTART			(1 << 0)
 #define MT9P031_SHUTTER_DELAY				0x0c
 #define MT9P031_RST					0x0d
 #define		MT9P031_RST_ENABLE			1
@@ -444,9 +446,23 @@
 static int mt9p031_s_stream(struct v4l2_subdev *subdev, int enable)
 {
 	struct mt9p031 *mt9p031 = to_mt9p031(subdev);
+	struct i2c_client *client = v4l2_get_subdevdata(subdev);
+	int val;
 	int ret;
 
 	if (!enable) {
+		/* enable pause restart */
+		val = MT9P031_FRAME_PAUSE_RESTART;
+		ret = mt9p031_write(client, MT9P031_RESTART, val);
+		if (ret < 0)
+			return ret;
+
+		/* enable restart + keep pause restart set */
+		val |= MT9P031_FRAME_RESTART;
+		ret = mt9p031_write(client, MT9P031_RESTART, val);
+		if (ret < 0)
+			return ret;
+
 		/* Stop sensor readout */
 		ret = mt9p031_set_output_control(mt9p031,
 						 MT9P031_OUTPUT_CONTROL_CEN, 0);
@@ -466,6 +482,16 @@
 	if (ret < 0)
 		return ret;
 
+	/*
+	 * - clear pause restart
+	 * - don't clear restart as clearing restart manually can cause
+	 *   undefined behavior
+	 */
+	val = MT9P031_FRAME_RESTART;
+	ret = mt9p031_write(client, MT9P031_RESTART, val);
+	if (ret < 0)
+		return ret;
+
 	return mt9p031_pll_enable(mt9p031);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov01a10.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov01a10.c
@@ -0,0 +1,948 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020-2021 Intel Corporation.
+
+#include <asm/unaligned.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/version.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <linux/vsc.h>
+
+#define OV01A10_LINK_FREQ_400MHZ	400000000ULL
+#define OV01A10_SCLK			40000000LL
+#define OV01A10_MCLK			19200000
+#define OV01A10_DATA_LANES		1
+#define OV01A10_RGB_DEPTH		10
+
+#define OV01A10_REG_CHIP_ID		0x300a
+#define OV01A10_CHIP_ID			0x560141
+
+#define OV01A10_REG_MODE_SELECT		0x0100
+#define OV01A10_MODE_STANDBY		0x00
+#define OV01A10_MODE_STREAMING		0x01
+
+/* vertical-timings from sensor */
+#define OV01A10_REG_VTS			0x380e
+#define OV01A10_VTS_DEF			0x0380
+#define OV01A10_VTS_MIN			0x0380
+#define OV01A10_VTS_MAX			0xffff
+
+/* Exposure controls from sensor */
+#define OV01A10_REG_EXPOSURE		0x3501
+#define OV01A10_EXPOSURE_MIN		4
+#define OV01A10_EXPOSURE_MAX_MARGIN	8
+#define OV01A10_EXPOSURE_STEP		1
+
+/* Analog gain controls from sensor */
+#define OV01A10_REG_ANALOG_GAIN		0x3508
+#define OV01A10_ANAL_GAIN_MIN		0x100
+#define OV01A10_ANAL_GAIN_MAX		0xffff
+#define OV01A10_ANAL_GAIN_STEP		1
+
+/* Digital gain controls from sensor */
+#define OV01A10_REG_DIGILAL_GAIN_B	0x350A
+#define OV01A10_REG_DIGITAL_GAIN_GB	0x3510
+#define OV01A10_REG_DIGITAL_GAIN_GR	0x3513
+#define OV01A10_REG_DIGITAL_GAIN_R	0x3516
+#define OV01A10_DGTL_GAIN_MIN		0
+#define OV01A10_DGTL_GAIN_MAX		0x3ffff
+#define OV01A10_DGTL_GAIN_STEP		1
+#define OV01A10_DGTL_GAIN_DEFAULT	1024
+
+/* Test Pattern Control */
+#define OV01A10_REG_TEST_PATTERN		0x4503
+#define OV01A10_TEST_PATTERN_ENABLE	BIT(7)
+#define OV01A10_TEST_PATTERN_BAR_SHIFT	0
+
+enum {
+	OV01A10_LINK_FREQ_400MHZ_INDEX,
+};
+
+struct ov01a10_reg {
+	u16 address;
+	u8 val;
+};
+
+struct ov01a10_reg_list {
+	u32 num_of_regs;
+	const struct ov01a10_reg *regs;
+};
+
+struct ov01a10_link_freq_config {
+	const struct ov01a10_reg_list reg_list;
+};
+
+struct ov01a10_mode {
+	/* Frame width in pixels */
+	u32 width;
+
+	/* Frame height in pixels */
+	u32 height;
+
+	/* Horizontal timining size */
+	u32 hts;
+
+	/* Default vertical timining size */
+	u32 vts_def;
+
+	/* Min vertical timining size */
+	u32 vts_min;
+
+	/* Link frequency needed for this resolution */
+	u32 link_freq_index;
+
+	/* Sensor register settings for this resolution */
+	const struct ov01a10_reg_list reg_list;
+};
+
+static const struct ov01a10_reg mipi_data_rate_720mbps[] = {
+};
+
+static const struct ov01a10_reg sensor_1280x800_setting[] = {
+	{0x0103, 0x01},
+	{0x0302, 0x00},
+	{0x0303, 0x06},
+	{0x0304, 0x01},
+	{0x0305, 0xe0},
+	{0x0306, 0x00},
+	{0x0308, 0x01},
+	{0x0309, 0x00},
+	{0x030c, 0x01},
+	{0x0322, 0x01},
+	{0x0323, 0x06},
+	{0x0324, 0x01},
+	{0x0325, 0x68},
+	{0x3002, 0xa1},
+	{0x301e, 0xf0},
+	{0x3022, 0x01},
+	{0x3501, 0x03},
+	{0x3502, 0x78},
+	{0x3504, 0x0c},
+	{0x3508, 0x01},
+	{0x3509, 0x00},
+	{0x3601, 0xc0},
+	{0x3603, 0x71},
+	{0x3610, 0x68},
+	{0x3611, 0x86},
+	{0x3640, 0x10},
+	{0x3641, 0x80},
+	{0x3642, 0xdc},
+	{0x3646, 0x55},
+	{0x3647, 0x57},
+	{0x364b, 0x00},
+	{0x3653, 0x10},
+	{0x3655, 0x00},
+	{0x3656, 0x00},
+	{0x365f, 0x0f},
+	{0x3661, 0x45},
+	{0x3662, 0x24},
+	{0x3663, 0x11},
+	{0x3664, 0x07},
+	{0x3709, 0x34},
+	{0x370b, 0x6f},
+	{0x3714, 0x22},
+	{0x371b, 0x27},
+	{0x371c, 0x67},
+	{0x371d, 0xa7},
+	{0x371e, 0xe7},
+	{0x3730, 0x81},
+	{0x3733, 0x10},
+	{0x3734, 0x40},
+	{0x3737, 0x04},
+	{0x3739, 0x1c},
+	{0x3767, 0x00},
+	{0x376c, 0x81},
+	{0x3772, 0x14},
+	{0x37c2, 0x04},
+	{0x37d8, 0x03},
+	{0x37d9, 0x0c},
+	{0x37e0, 0x00},
+	{0x37e1, 0x08},
+	{0x37e2, 0x10},
+	{0x37e3, 0x04},
+	{0x37e4, 0x04},
+	{0x37e5, 0x03},
+	{0x37e6, 0x04},
+	{0x3800, 0x00},
+	{0x3801, 0x00},
+	{0x3802, 0x00},
+	{0x3803, 0x00},
+	{0x3804, 0x05},
+	{0x3805, 0x0f},
+	{0x3806, 0x03},
+	{0x3807, 0x2f},
+	{0x3808, 0x05},
+	{0x3809, 0x00},
+	{0x380a, 0x03},
+	{0x380b, 0x20},
+	{0x380c, 0x02},
+	{0x380d, 0xe8},
+	{0x380e, 0x03},
+	{0x380f, 0x80},
+	{0x3810, 0x00},
+	{0x3811, 0x09},
+	{0x3812, 0x00},
+	{0x3813, 0x08},
+	{0x3814, 0x01},
+	{0x3815, 0x01},
+	{0x3816, 0x01},
+	{0x3817, 0x01},
+	{0x3820, 0xa8},
+	{0x3822, 0x13},
+	{0x3832, 0x28},
+	{0x3833, 0x10},
+	{0x3b00, 0x00},
+	{0x3c80, 0x00},
+	{0x3c88, 0x02},
+	{0x3c8c, 0x07},
+	{0x3c8d, 0x40},
+	{0x3cc7, 0x80},
+	{0x4000, 0xc3},
+	{0x4001, 0xe0},
+	{0x4003, 0x40},
+	{0x4008, 0x02},
+	{0x4009, 0x19},
+	{0x400a, 0x01},
+	{0x400b, 0x6c},
+	{0x4011, 0x00},
+	{0x4041, 0x00},
+	{0x4300, 0xff},
+	{0x4301, 0x00},
+	{0x4302, 0x0f},
+	{0x4503, 0x00},
+	{0x4601, 0x50},
+	{0x4800, 0x64},
+	{0x481f, 0x34},
+	{0x4825, 0x33},
+	{0x4837, 0x11},
+	{0x4881, 0x40},
+	{0x4883, 0x01},
+	{0x4890, 0x00},
+	{0x4901, 0x00},
+	{0x4902, 0x00},
+	{0x4b00, 0x2a},
+	{0x4b0d, 0x00},
+	{0x450a, 0x04},
+	{0x450b, 0x00},
+	{0x5000, 0x65},
+	{0x5200, 0x18},
+	{0x5004, 0x00},
+	{0x5080, 0x40},
+	{0x0305, 0xf4},
+	{0x0325, 0xc2},
+	{0x380c, 0x05},
+	{0x380d, 0xd0},
+};
+
+static const char * const ov01a10_test_pattern_menu[] = {
+	"Disabled",
+	"Color Bar",
+	"Top-Bottom Darker Color Bar",
+	"Right-Left Darker Color Bar",
+	"Color Bar type 4",
+};
+
+static const s64 link_freq_menu_items[] = {
+	OV01A10_LINK_FREQ_400MHZ,
+};
+
+static const struct ov01a10_link_freq_config link_freq_configs[] = {
+	[OV01A10_LINK_FREQ_400MHZ_INDEX] = {
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(mipi_data_rate_720mbps),
+			.regs = mipi_data_rate_720mbps,
+		}
+	},
+};
+
+static const struct ov01a10_mode supported_modes[] = {
+	{
+		.width = 1280,
+		.height = 800,
+		.hts = 1488,
+		.vts_def = OV01A10_VTS_DEF,
+		.vts_min = OV01A10_VTS_MIN,
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(sensor_1280x800_setting),
+			.regs = sensor_1280x800_setting,
+		},
+		.link_freq_index = OV01A10_LINK_FREQ_400MHZ_INDEX,
+	},
+};
+
+struct ov01a10 {
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* V4L2 Controls */
+	struct v4l2_ctrl *link_freq;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *exposure;
+
+	/* Current mode */
+	const struct ov01a10_mode *cur_mode;
+
+	/* To serialize asynchronus callbacks */
+	struct mutex mutex;
+
+	/* Streaming on/off */
+	bool streaming;
+};
+
+static inline struct ov01a10 *to_ov01a10(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct ov01a10, sd);
+}
+
+static int ov01a10_read_reg(struct ov01a10 *ov01a10, u16 reg, u16 len, u32 *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	struct i2c_msg msgs[2];
+	u8 addr_buf[2];
+	u8 data_buf[4] = {0};
+	int ret = 0;
+
+	if (len > sizeof(data_buf))
+		return -EINVAL;
+
+	put_unaligned_be16(reg, addr_buf);
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = sizeof(addr_buf);
+	msgs[0].buf = addr_buf;
+	msgs[1].addr = client->addr;
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].len = len;
+	msgs[1].buf = &data_buf[sizeof(data_buf) - len];
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+
+	if (ret != ARRAY_SIZE(msgs))
+		return ret < 0 ? ret : -EIO;
+
+	*val = get_unaligned_be32(data_buf);
+
+	return 0;
+}
+
+static int ov01a10_write_reg(struct ov01a10 *ov01a10, u16 reg, u16 len, u32 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	u8 buf[6];
+	int ret = 0;
+
+	if (len > 4)
+		return -EINVAL;
+
+	put_unaligned_be16(reg, buf);
+	put_unaligned_be32(val << 8 * (4 - len), buf + 2);
+
+	ret = i2c_master_send(client, buf, len + 2);
+	if (ret != len + 2)
+		return ret < 0 ? ret : -EIO;
+
+	return 0;
+}
+
+static int ov01a10_write_reg_list(struct ov01a10 *ov01a10,
+				  const struct ov01a10_reg_list *r_list)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	unsigned int i;
+	int ret = 0;
+
+	for (i = 0; i < r_list->num_of_regs; i++) {
+		ret = ov01a10_write_reg(ov01a10, r_list->regs[i].address, 1,
+					r_list->regs[i].val);
+		if (ret) {
+			dev_err_ratelimited(&client->dev,
+					    "write reg 0x%4.4x return err = %d",
+					    r_list->regs[i].address, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int ov01a10_update_digital_gain(struct ov01a10 *ov01a10, u32 d_gain)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	u32 real = d_gain << 6;
+	int ret = 0;
+
+	ret = ov01a10_write_reg(ov01a10, OV01A10_REG_DIGILAL_GAIN_B, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A10_REG_DIGITAL_GAIN_B");
+		return ret;
+	}
+	ret = ov01a10_write_reg(ov01a10, OV01A10_REG_DIGITAL_GAIN_GB, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A10_REG_DIGITAL_GAIN_GB");
+		return ret;
+	}
+	ret = ov01a10_write_reg(ov01a10, OV01A10_REG_DIGITAL_GAIN_GR, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A10_REG_DIGITAL_GAIN_GR");
+		return ret;
+	}
+
+	ret = ov01a10_write_reg(ov01a10, OV01A10_REG_DIGITAL_GAIN_R, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A10_REG_DIGITAL_GAIN_R");
+		return ret;
+	}
+	return ret;
+}
+
+static int ov01a10_test_pattern(struct ov01a10 *ov01a10, u32 pattern)
+{
+	if (pattern)
+		pattern = (pattern - 1) << OV01A10_TEST_PATTERN_BAR_SHIFT |
+			  OV01A10_TEST_PATTERN_ENABLE;
+
+	return ov01a10_write_reg(ov01a10, OV01A10_REG_TEST_PATTERN, 1, pattern);
+}
+
+static int ov01a10_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ov01a10 *ov01a10 = container_of(ctrl->handler,
+					     struct ov01a10, ctrl_handler);
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	s64 exposure_max;
+	int ret = 0;
+
+	/* Propagate change of current control to all related controls */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Update max exposure while meeting expected vblanking */
+		exposure_max = ov01a10->cur_mode->height + ctrl->val -
+			       OV01A10_EXPOSURE_MAX_MARGIN;
+		__v4l2_ctrl_modify_range(ov01a10->exposure,
+					 ov01a10->exposure->minimum,
+					 exposure_max, ov01a10->exposure->step,
+					 exposure_max);
+	}
+
+	/* V4L2 controls values will be applied only when power is already up */
+	if (!pm_runtime_get_if_in_use(&client->dev))
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = ov01a10_write_reg(ov01a10, OV01A10_REG_ANALOG_GAIN, 2,
+					ctrl->val);
+		break;
+
+	case V4L2_CID_DIGITAL_GAIN:
+		ret = ov01a10_update_digital_gain(ov01a10, ctrl->val);
+		break;
+
+	case V4L2_CID_EXPOSURE:
+		ret = ov01a10_write_reg(ov01a10, OV01A10_REG_EXPOSURE, 2,
+					ctrl->val);
+		break;
+
+	case V4L2_CID_VBLANK:
+		ret = ov01a10_write_reg(ov01a10, OV01A10_REG_VTS, 2,
+					ov01a10->cur_mode->height + ctrl->val);
+		break;
+
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov01a10_test_pattern(ov01a10, ctrl->val);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	pm_runtime_put(&client->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov01a10_ctrl_ops = {
+	.s_ctrl = ov01a10_set_ctrl,
+};
+
+static int ov01a10_init_controls(struct ov01a10 *ov01a10)
+{
+	struct v4l2_ctrl_handler *ctrl_hdlr;
+	const struct ov01a10_mode *cur_mode;
+	s64 exposure_max, h_blank;
+	u32 vblank_min, vblank_max, vblank_default;
+	int size;
+	int ret = 0;
+
+	ctrl_hdlr = &ov01a10->ctrl_handler;
+	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8);
+	if (ret)
+		return ret;
+
+	ctrl_hdlr->lock = &ov01a10->mutex;
+	cur_mode = ov01a10->cur_mode;
+	size = ARRAY_SIZE(link_freq_menu_items);
+
+	ov01a10->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr,
+						    &ov01a10_ctrl_ops,
+						    V4L2_CID_LINK_FREQ,
+						    size - 1, 0,
+						    link_freq_menu_items);
+	if (ov01a10->link_freq)
+		ov01a10->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	ov01a10->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a10_ctrl_ops,
+						V4L2_CID_PIXEL_RATE, 0,
+						OV01A10_SCLK, 1, OV01A10_SCLK);
+
+	vblank_min = cur_mode->vts_min - cur_mode->height;
+	vblank_max = OV01A10_VTS_MAX - cur_mode->height;
+	vblank_default = cur_mode->vts_def - cur_mode->height;
+	ov01a10->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a10_ctrl_ops,
+					    V4L2_CID_VBLANK, vblank_min,
+					    vblank_max, 1, vblank_default);
+
+	h_blank = cur_mode->hts - cur_mode->width;
+	ov01a10->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a10_ctrl_ops,
+					    V4L2_CID_HBLANK, h_blank, h_blank,
+					    1, h_blank);
+	if (ov01a10->hblank)
+		ov01a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov01a10_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+			  OV01A10_ANAL_GAIN_MIN, OV01A10_ANAL_GAIN_MAX,
+			  OV01A10_ANAL_GAIN_STEP, OV01A10_ANAL_GAIN_MIN);
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov01a10_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+			  OV01A10_DGTL_GAIN_MIN, OV01A10_DGTL_GAIN_MAX,
+			  OV01A10_DGTL_GAIN_STEP, OV01A10_DGTL_GAIN_DEFAULT);
+	exposure_max = cur_mode->vts_def - OV01A10_EXPOSURE_MAX_MARGIN;
+	ov01a10->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a10_ctrl_ops,
+					      V4L2_CID_EXPOSURE,
+					      OV01A10_EXPOSURE_MIN,
+					      exposure_max,
+					      OV01A10_EXPOSURE_STEP,
+					      exposure_max);
+	v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov01a10_ctrl_ops,
+				     V4L2_CID_TEST_PATTERN,
+				     ARRAY_SIZE(ov01a10_test_pattern_menu) - 1,
+				     0, 0, ov01a10_test_pattern_menu);
+	if (ctrl_hdlr->error)
+		return ctrl_hdlr->error;
+
+	ov01a10->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+}
+
+static void ov01a10_update_pad_format(const struct ov01a10_mode *mode,
+				      struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	fmt->field = V4L2_FIELD_NONE;
+}
+
+static int ov01a10_start_streaming(struct ov01a10 *ov01a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	const struct ov01a10_reg_list *reg_list;
+	int link_freq_index;
+	int ret = 0;
+	struct vsc_mipi_config conf;
+	struct vsc_camera_status status;
+
+	conf.lane_num = OV01A10_DATA_LANES;
+	/* frequency unit 100k */
+	conf.freq = OV01A10_LINK_FREQ_400MHZ / 100000;
+	ret = vsc_acquire_camera_sensor(&conf, NULL, NULL, &status);
+	if (ret) {
+		dev_err(&client->dev, "Acquire VSC failed");
+		return ret;
+	}
+	link_freq_index = ov01a10->cur_mode->link_freq_index;
+	reg_list = &link_freq_configs[link_freq_index].reg_list;
+	ret = ov01a10_write_reg_list(ov01a10, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set plls");
+		return ret;
+	}
+
+	reg_list = &ov01a10->cur_mode->reg_list;
+	ret = ov01a10_write_reg_list(ov01a10, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set mode");
+		return ret;
+	}
+
+	ret = __v4l2_ctrl_handler_setup(ov01a10->sd.ctrl_handler);
+	if (ret)
+		return ret;
+
+	ret = ov01a10_write_reg(ov01a10, OV01A10_REG_MODE_SELECT, 1,
+				OV01A10_MODE_STREAMING);
+	if (ret)
+		dev_err(&client->dev, "failed to start streaming");
+
+	return ret;
+}
+
+static void ov01a10_stop_streaming(struct ov01a10 *ov01a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	int ret = 0;
+	struct vsc_camera_status status;
+
+	ret = ov01a10_write_reg(ov01a10, OV01A10_REG_MODE_SELECT, 1,
+				OV01A10_MODE_STANDBY);
+	if (ret)
+		dev_err(&client->dev, "failed to stop streaming");
+	ret = vsc_release_camera_sensor(&status);
+	if (ret)
+		dev_err(&client->dev, "Release VSC failed");
+}
+
+static int ov01a10_set_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	if (ov01a10->streaming == enable)
+		return 0;
+
+	mutex_lock(&ov01a10->mutex);
+	if (enable) {
+		ret = pm_runtime_get_sync(&client->dev);
+		if (ret < 0) {
+			pm_runtime_put_noidle(&client->dev);
+			mutex_unlock(&ov01a10->mutex);
+			return ret;
+		}
+
+		ret = ov01a10_start_streaming(ov01a10);
+		if (ret) {
+			enable = 0;
+			ov01a10_stop_streaming(ov01a10);
+			pm_runtime_put(&client->dev);
+		}
+	} else {
+		ov01a10_stop_streaming(ov01a10);
+		pm_runtime_put(&client->dev);
+	}
+
+	ov01a10->streaming = enable;
+	mutex_unlock(&ov01a10->mutex);
+
+	return ret;
+}
+
+static int __maybe_unused ov01a10_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+
+	mutex_lock(&ov01a10->mutex);
+	if (ov01a10->streaming)
+		ov01a10_stop_streaming(ov01a10);
+
+	mutex_unlock(&ov01a10->mutex);
+
+	return 0;
+}
+
+static int __maybe_unused ov01a10_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+	int ret = 0;
+
+	mutex_lock(&ov01a10->mutex);
+	if (!ov01a10->streaming)
+		goto exit;
+
+	ret = ov01a10_start_streaming(ov01a10);
+	if (ret) {
+		ov01a10->streaming = false;
+		ov01a10_stop_streaming(ov01a10);
+	}
+
+exit:
+	mutex_unlock(&ov01a10->mutex);
+	return ret;
+}
+
+static int ov01a10_set_format(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+	const struct ov01a10_mode *mode;
+	s32 vblank_def, h_blank;
+
+	mode = v4l2_find_nearest_size(supported_modes,
+				      ARRAY_SIZE(supported_modes), width,
+				      height, fmt->format.width,
+				      fmt->format.height);
+
+	mutex_lock(&ov01a10->mutex);
+	ov01a10_update_pad_format(mode, &fmt->format);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
+		*v4l2_subdev_get_try_format(sd, sd_state, fmt->pad) = fmt->format;
+	} else {
+		ov01a10->cur_mode = mode;
+		__v4l2_ctrl_s_ctrl(ov01a10->link_freq, mode->link_freq_index);
+		__v4l2_ctrl_s_ctrl_int64(ov01a10->pixel_rate, OV01A10_SCLK);
+
+		/* Update limits and set FPS to default */
+		vblank_def = mode->vts_def - mode->height;
+		__v4l2_ctrl_modify_range(ov01a10->vblank,
+					 mode->vts_min - mode->height,
+					 OV01A10_VTS_MAX - mode->height, 1,
+					 vblank_def);
+		__v4l2_ctrl_s_ctrl(ov01a10->vblank, vblank_def);
+		h_blank = mode->hts - mode->width;
+		__v4l2_ctrl_modify_range(ov01a10->hblank, h_blank, h_blank, 1,
+					 h_blank);
+	}
+	mutex_unlock(&ov01a10->mutex);
+
+	return 0;
+}
+
+static int ov01a10_get_format(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+
+	mutex_lock(&ov01a10->mutex);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt->format = *v4l2_subdev_get_try_format(&ov01a10->sd,
+							  sd_state, fmt->pad);
+	else
+		ov01a10_update_pad_format(ov01a10->cur_mode, &fmt->format);
+
+	mutex_unlock(&ov01a10->mutex);
+
+	return 0;
+}
+
+static int ov01a10_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->index > 0)
+		return -EINVAL;
+
+	code->code = MEDIA_BUS_FMT_SBGGR10_1X10;
+
+	return 0;
+}
+
+static int ov01a10_enum_frame_size(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->index >= ARRAY_SIZE(supported_modes))
+		return -EINVAL;
+
+	if (fse->code != MEDIA_BUS_FMT_SBGGR10_1X10)
+		return -EINVAL;
+
+	fse->min_width = supported_modes[fse->index].width;
+	fse->max_width = fse->min_width;
+	fse->min_height = supported_modes[fse->index].height;
+	fse->max_height = fse->min_height;
+
+	return 0;
+}
+
+static int ov01a10_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+
+	mutex_lock(&ov01a10->mutex);
+	ov01a10_update_pad_format(&supported_modes[0],
+				  v4l2_subdev_get_try_format(sd, fh->state, 0));
+	mutex_unlock(&ov01a10->mutex);
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops ov01a10_video_ops = {
+	.s_stream = ov01a10_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov01a10_pad_ops = {
+	.set_fmt = ov01a10_set_format,
+	.get_fmt = ov01a10_get_format,
+	.enum_mbus_code = ov01a10_enum_mbus_code,
+	.enum_frame_size = ov01a10_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops ov01a10_subdev_ops = {
+	.video = &ov01a10_video_ops,
+	.pad = &ov01a10_pad_ops,
+};
+
+static const struct media_entity_operations ov01a10_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static const struct v4l2_subdev_internal_ops ov01a10_internal_ops = {
+	.open = ov01a10_open,
+};
+
+static int ov01a10_identify_module(struct ov01a10 *ov01a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a10->sd);
+	int ret;
+	u32 val;
+
+	ret = ov01a10_read_reg(ov01a10, OV01A10_REG_CHIP_ID, 3, &val);
+	if (ret)
+		return ret;
+
+	if (val != OV01A10_CHIP_ID) {
+		dev_err(&client->dev, "chip id mismatch: %x!=%x",
+			OV01A10_CHIP_ID, val);
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int ov01a10_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov01a10 *ov01a10 = to_ov01a10(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(sd->ctrl_handler);
+	pm_runtime_disable(&client->dev);
+	mutex_destroy(&ov01a10->mutex);
+
+	return 0;
+}
+
+static int ov01a10_probe(struct i2c_client *client)
+{
+	struct ov01a10 *ov01a10;
+	int ret = 0;
+	struct vsc_mipi_config conf;
+	struct vsc_camera_status status;
+
+	conf.lane_num = OV01A10_DATA_LANES;
+	/* frequency unit 100k */
+	conf.freq = OV01A10_LINK_FREQ_400MHZ / 100000;
+	ret = vsc_acquire_camera_sensor(&conf, NULL, NULL, &status);
+	if (ret == -EAGAIN) {
+		dev_dbg(&client->dev, "VSC not ready, will re-probe");
+		return -EPROBE_DEFER;
+	} else if (ret) {
+		dev_err(&client->dev, "Acquire VSC failed");
+		return ret;
+	}
+	ov01a10 = devm_kzalloc(&client->dev, sizeof(*ov01a10), GFP_KERNEL);
+	if (!ov01a10) {
+		ret = -ENOMEM;
+		goto probe_error_ret;
+	}
+
+	v4l2_i2c_subdev_init(&ov01a10->sd, client, &ov01a10_subdev_ops);
+
+	ret = ov01a10_identify_module(ov01a10);
+	if (ret) {
+		dev_err(&client->dev, "failed to find sensor: %d", ret);
+		goto probe_error_ret;
+	}
+
+	mutex_init(&ov01a10->mutex);
+	ov01a10->cur_mode = &supported_modes[0];
+	ret = ov01a10_init_controls(ov01a10);
+	if (ret) {
+		dev_err(&client->dev, "failed to init controls: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ov01a10->sd.internal_ops = &ov01a10_internal_ops;
+	ov01a10->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	ov01a10->sd.entity.ops = &ov01a10_subdev_entity_ops;
+	ov01a10->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ov01a10->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&ov01a10->sd.entity, 1, &ov01a10->pad);
+	if (ret) {
+		dev_err(&client->dev, "failed to init entity pads: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ret = v4l2_async_register_subdev_sensor(&ov01a10->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto probe_error_media_entity_cleanup;
+	}
+
+	vsc_release_camera_sensor(&status);
+	/*
+	 * Device is already turned on by i2c-core with ACPI domain PM.
+	 * Enable runtime PM and turn off the device.
+	 */
+	pm_runtime_set_active(&client->dev);
+	pm_runtime_enable(&client->dev);
+	pm_runtime_idle(&client->dev);
+
+	return 0;
+
+probe_error_media_entity_cleanup:
+	media_entity_cleanup(&ov01a10->sd.entity);
+
+probe_error_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(ov01a10->sd.ctrl_handler);
+	mutex_destroy(&ov01a10->mutex);
+
+probe_error_ret:
+	vsc_release_camera_sensor(&status);
+	return ret;
+}
+
+static const struct dev_pm_ops ov01a10_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(ov01a10_suspend, ov01a10_resume)
+};
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id ov01a10_acpi_ids[] = {
+	{"OVTI01A0"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(acpi, ov01a10_acpi_ids);
+#endif
+
+static struct i2c_driver ov01a10_i2c_driver = {
+	.driver = {
+		.name = "ov01a10",
+		.pm = &ov01a10_pm_ops,
+		.acpi_match_table = ACPI_PTR(ov01a10_acpi_ids),
+	},
+	.probe_new = ov01a10_probe,
+	.remove = ov01a10_remove,
+};
+
+module_i2c_driver(ov01a10_i2c_driver);
+
+MODULE_AUTHOR("Wang Yating <yating.wang@intel.com>");
+MODULE_DESCRIPTION("OmniVision OV01A10 sensor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov01a1s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov01a1s.c
@@ -0,0 +1,937 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020-2021 Intel Corporation.
+
+#include <asm/unaligned.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/version.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include "power_ctrl_logic.h"
+
+#define OV01A1S_LINK_FREQ_400MHZ	400000000ULL
+#define OV01A1S_SCLK			40000000LL
+#define OV01A1S_MCLK			19200000
+#define OV01A1S_DATA_LANES		1
+#define OV01A1S_RGB_DEPTH		10
+
+#define OV01A1S_REG_CHIP_ID		0x300a
+#define OV01A1S_CHIP_ID			0x560141
+
+#define OV01A1S_REG_MODE_SELECT		0x0100
+#define OV01A1S_MODE_STANDBY		0x00
+#define OV01A1S_MODE_STREAMING		0x01
+
+/* vertical-timings from sensor */
+#define OV01A1S_REG_VTS			0x380e
+#define OV01A1S_VTS_DEF			0x0380
+#define OV01A1S_VTS_MIN			0x0380
+#define OV01A1S_VTS_MAX			0xffff
+
+/* Exposure controls from sensor */
+#define OV01A1S_REG_EXPOSURE		0x3501
+#define OV01A1S_EXPOSURE_MIN		4
+#define OV01A1S_EXPOSURE_MAX_MARGIN	8
+#define OV01A1S_EXPOSURE_STEP		1
+
+/* Analog gain controls from sensor */
+#define OV01A1S_REG_ANALOG_GAIN		0x3508
+#define OV01A1S_ANAL_GAIN_MIN		0x100
+#define OV01A1S_ANAL_GAIN_MAX		0xffff
+#define OV01A1S_ANAL_GAIN_STEP		1
+
+/* Digital gain controls from sensor */
+#define OV01A1S_REG_DIGILAL_GAIN_B	0x350A
+#define OV01A1S_REG_DIGITAL_GAIN_GB	0x3510
+#define OV01A1S_REG_DIGITAL_GAIN_GR	0x3513
+#define OV01A1S_REG_DIGITAL_GAIN_R	0x3516
+#define OV01A1S_DGTL_GAIN_MIN		0
+#define OV01A1S_DGTL_GAIN_MAX		0x3ffff
+#define OV01A1S_DGTL_GAIN_STEP		1
+#define OV01A1S_DGTL_GAIN_DEFAULT	1024
+
+/* Test Pattern Control */
+#define OV01A1S_REG_TEST_PATTERN		0x4503
+#define OV01A1S_TEST_PATTERN_ENABLE	BIT(7)
+#define OV01A1S_TEST_PATTERN_BAR_SHIFT	0
+
+enum {
+	OV01A1S_LINK_FREQ_400MHZ_INDEX,
+};
+
+struct ov01a1s_reg {
+	u16 address;
+	u8 val;
+};
+
+struct ov01a1s_reg_list {
+	u32 num_of_regs;
+	const struct ov01a1s_reg *regs;
+};
+
+struct ov01a1s_link_freq_config {
+	const struct ov01a1s_reg_list reg_list;
+};
+
+struct ov01a1s_mode {
+	/* Frame width in pixels */
+	u32 width;
+
+	/* Frame height in pixels */
+	u32 height;
+
+	/* Horizontal timining size */
+	u32 hts;
+
+	/* Default vertical timining size */
+	u32 vts_def;
+
+	/* Min vertical timining size */
+	u32 vts_min;
+
+	/* Link frequency needed for this resolution */
+	u32 link_freq_index;
+
+	/* Sensor register settings for this resolution */
+	const struct ov01a1s_reg_list reg_list;
+};
+
+static const struct ov01a1s_reg mipi_data_rate_720mbps[] = {
+};
+
+static const struct ov01a1s_reg sensor_1296x800_setting[] = {
+	{0x0103, 0x01},
+	{0x0302, 0x00},
+	{0x0303, 0x06},
+	{0x0304, 0x01},
+	{0x0305, 0x90},
+	{0x0306, 0x00},
+	{0x0308, 0x01},
+	{0x0309, 0x00},
+	{0x030c, 0x01},
+	{0x0322, 0x01},
+	{0x0323, 0x06},
+	{0x0324, 0x01},
+	{0x0325, 0x68},
+	{0x3002, 0xa1},
+	{0x301e, 0xf0},
+	{0x3022, 0x01},
+	{0x3501, 0x03},
+	{0x3502, 0x78},
+	{0x3504, 0x0c},
+	{0x3508, 0x01},
+	{0x3509, 0x00},
+	{0x3601, 0xc0},
+	{0x3603, 0x71},
+	{0x3610, 0x68},
+	{0x3611, 0x86},
+	{0x3640, 0x10},
+	{0x3641, 0x80},
+	{0x3642, 0xdc},
+	{0x3646, 0x55},
+	{0x3647, 0x57},
+	{0x364b, 0x00},
+	{0x3653, 0x10},
+	{0x3655, 0x00},
+	{0x3656, 0x00},
+	{0x365f, 0x0f},
+	{0x3661, 0x45},
+	{0x3662, 0x24},
+	{0x3663, 0x11},
+	{0x3664, 0x07},
+	{0x3709, 0x34},
+	{0x370b, 0x6f},
+	{0x3714, 0x22},
+	{0x371b, 0x27},
+	{0x371c, 0x67},
+	{0x371d, 0xa7},
+	{0x371e, 0xe7},
+	{0x3730, 0x81},
+	{0x3733, 0x10},
+	{0x3734, 0x40},
+	{0x3737, 0x04},
+	{0x3739, 0x1c},
+	{0x3767, 0x00},
+	{0x376c, 0x81},
+	{0x3772, 0x14},
+	{0x37c2, 0x04},
+	{0x37d8, 0x03},
+	{0x37d9, 0x0c},
+	{0x37e0, 0x00},
+	{0x37e1, 0x08},
+	{0x37e2, 0x10},
+	{0x37e3, 0x04},
+	{0x37e4, 0x04},
+	{0x37e5, 0x03},
+	{0x37e6, 0x04},
+	{0x3800, 0x00},
+	{0x3801, 0x00},
+	{0x3802, 0x00},
+	{0x3803, 0x00},
+	{0x3804, 0x05},
+	{0x3805, 0x0f},
+	{0x3806, 0x03},
+	{0x3807, 0x2f},
+	{0x3808, 0x05},
+	{0x3809, 0x00},
+	{0x380a, 0x03},
+	{0x380b, 0x1e},
+	{0x380c, 0x05},
+	{0x380d, 0xd0},
+	{0x380e, 0x03},
+	{0x380f, 0x80},
+	{0x3810, 0x00},
+	{0x3811, 0x09},
+	{0x3812, 0x00},
+	{0x3813, 0x08},
+	{0x3814, 0x01},
+	{0x3815, 0x01},
+	{0x3816, 0x01},
+	{0x3817, 0x01},
+	{0x3820, 0xa8},
+	{0x3822, 0x03},
+	{0x3832, 0x28},
+	{0x3833, 0x10},
+	{0x3b00, 0x00},
+	{0x3c80, 0x00},
+	{0x3c88, 0x02},
+	{0x3c8c, 0x07},
+	{0x3c8d, 0x40},
+	{0x3cc7, 0x80},
+	{0x4000, 0xc3},
+	{0x4001, 0xe0},
+	{0x4003, 0x40},
+	{0x4008, 0x02},
+	{0x4009, 0x19},
+	{0x400a, 0x01},
+	{0x400b, 0x6c},
+	{0x4011, 0x00},
+	{0x4041, 0x00},
+	{0x4300, 0xff},
+	{0x4301, 0x00},
+	{0x4302, 0x0f},
+	{0x4503, 0x00},
+	{0x4601, 0x50},
+	{0x481f, 0x34},
+	{0x4825, 0x33},
+	{0x4837, 0x14},
+	{0x4881, 0x40},
+	{0x4883, 0x01},
+	{0x4890, 0x00},
+	{0x4901, 0x00},
+	{0x4902, 0x00},
+	{0x4b00, 0x2a},
+	{0x4b0d, 0x00},
+	{0x450a, 0x04},
+	{0x450b, 0x00},
+	{0x5000, 0x65},
+	{0x5004, 0x00},
+	{0x5080, 0x40},
+	{0x5200, 0x18},
+	{0x4837, 0x14},
+	{0x0305, 0xf4},
+	{0x0325, 0xc2},
+	{0x3808, 0x05},
+	{0x3809, 0x10},
+	{0x380a, 0x03},
+	{0x380b, 0x1e},
+	{0x3810, 0x00},
+	{0x3811, 0x00},
+	{0x3812, 0x00},
+	{0x3813, 0x09},
+	{0x3820, 0x88},
+	{0x373d, 0x24},
+};
+
+static const char * const ov01a1s_test_pattern_menu[] = {
+	"Disabled",
+	"Color Bar",
+	"Top-Bottom Darker Color Bar",
+	"Right-Left Darker Color Bar",
+	"Color Bar type 4",
+};
+
+static const s64 link_freq_menu_items[] = {
+	OV01A1S_LINK_FREQ_400MHZ,
+};
+
+static const struct ov01a1s_link_freq_config link_freq_configs[] = {
+	[OV01A1S_LINK_FREQ_400MHZ_INDEX] = {
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(mipi_data_rate_720mbps),
+			.regs = mipi_data_rate_720mbps,
+		}
+	},
+};
+
+static const struct ov01a1s_mode supported_modes[] = {
+	{
+		.width = 1296,
+		.height = 798,
+		.hts = 1488,
+		.vts_def = OV01A1S_VTS_DEF,
+		.vts_min = OV01A1S_VTS_MIN,
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(sensor_1296x800_setting),
+			.regs = sensor_1296x800_setting,
+		},
+		.link_freq_index = OV01A1S_LINK_FREQ_400MHZ_INDEX,
+	},
+};
+
+struct ov01a1s {
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* V4L2 Controls */
+	struct v4l2_ctrl *link_freq;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *exposure;
+
+	/* Current mode */
+	const struct ov01a1s_mode *cur_mode;
+
+	/* To serialize asynchronus callbacks */
+	struct mutex mutex;
+
+	/* Streaming on/off */
+	bool streaming;
+};
+
+static inline struct ov01a1s *to_ov01a1s(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct ov01a1s, sd);
+}
+
+static int ov01a1s_read_reg(struct ov01a1s *ov01a1s, u16 reg, u16 len, u32 *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	struct i2c_msg msgs[2];
+	u8 addr_buf[2];
+	u8 data_buf[4] = {0};
+	int ret = 0;
+
+	if (len > sizeof(data_buf))
+		return -EINVAL;
+
+	put_unaligned_be16(reg, addr_buf);
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = sizeof(addr_buf);
+	msgs[0].buf = addr_buf;
+	msgs[1].addr = client->addr;
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].len = len;
+	msgs[1].buf = &data_buf[sizeof(data_buf) - len];
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret != ARRAY_SIZE(msgs))
+		return ret < 0 ? ret : -EIO;
+
+	*val = get_unaligned_be32(data_buf);
+
+	return 0;
+}
+
+static int ov01a1s_write_reg(struct ov01a1s *ov01a1s, u16 reg, u16 len, u32 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	u8 buf[6];
+	int ret = 0;
+
+	if (len > 4)
+		return -EINVAL;
+
+	put_unaligned_be16(reg, buf);
+	put_unaligned_be32(val << 8 * (4 - len), buf + 2);
+
+	ret = i2c_master_send(client, buf, len + 2);
+	if (ret != len + 2)
+		return ret < 0 ? ret : -EIO;
+
+	return 0;
+}
+
+static int ov01a1s_write_reg_list(struct ov01a1s *ov01a1s,
+				  const struct ov01a1s_reg_list *r_list)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	unsigned int i;
+	int ret = 0;
+
+	for (i = 0; i < r_list->num_of_regs; i++) {
+		ret = ov01a1s_write_reg(ov01a1s, r_list->regs[i].address, 1,
+					r_list->regs[i].val);
+		if (ret) {
+			dev_err_ratelimited(&client->dev,
+					    "write reg 0x%4.4x return err = %d",
+					    r_list->regs[i].address, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int ov01a1s_update_digital_gain(struct ov01a1s *ov01a1s, u32 d_gain)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	u32 real = d_gain << 6;
+	int ret = 0;
+
+	ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_DIGILAL_GAIN_B, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A1S_REG_DIGITAL_GAIN_B");
+		return ret;
+	}
+	ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_DIGITAL_GAIN_GB, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A1S_REG_DIGITAL_GAIN_GB");
+		return ret;
+	}
+	ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_DIGITAL_GAIN_GR, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A1S_REG_DIGITAL_GAIN_GR");
+		return ret;
+	}
+
+	ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_DIGITAL_GAIN_R, 3, real);
+	if (ret) {
+		dev_err(&client->dev, "failed to set OV01A1S_REG_DIGITAL_GAIN_R");
+		return ret;
+	}
+	return ret;
+}
+
+static int ov01a1s_test_pattern(struct ov01a1s *ov01a1s, u32 pattern)
+{
+	if (pattern)
+		pattern = (pattern - 1) << OV01A1S_TEST_PATTERN_BAR_SHIFT |
+			  OV01A1S_TEST_PATTERN_ENABLE;
+
+	return ov01a1s_write_reg(ov01a1s, OV01A1S_REG_TEST_PATTERN, 1, pattern);
+}
+
+static int ov01a1s_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ov01a1s *ov01a1s = container_of(ctrl->handler,
+					     struct ov01a1s, ctrl_handler);
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	s64 exposure_max;
+	int ret = 0;
+
+	/* Propagate change of current control to all related controls */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Update max exposure while meeting expected vblanking */
+		exposure_max = ov01a1s->cur_mode->height + ctrl->val -
+			       OV01A1S_EXPOSURE_MAX_MARGIN;
+		__v4l2_ctrl_modify_range(ov01a1s->exposure,
+					 ov01a1s->exposure->minimum,
+					 exposure_max, ov01a1s->exposure->step,
+					 exposure_max);
+	}
+
+	/* V4L2 controls values will be applied only when power is already up */
+	if (!pm_runtime_get_if_in_use(&client->dev))
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_ANALOG_GAIN, 2,
+					ctrl->val);
+		break;
+
+	case V4L2_CID_DIGITAL_GAIN:
+		ret = ov01a1s_update_digital_gain(ov01a1s, ctrl->val);
+		break;
+
+	case V4L2_CID_EXPOSURE:
+		ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_EXPOSURE, 2,
+					ctrl->val);
+		break;
+
+	case V4L2_CID_VBLANK:
+		ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_VTS, 2,
+					ov01a1s->cur_mode->height + ctrl->val);
+		break;
+
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov01a1s_test_pattern(ov01a1s, ctrl->val);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	pm_runtime_put(&client->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov01a1s_ctrl_ops = {
+	.s_ctrl = ov01a1s_set_ctrl,
+};
+
+static int ov01a1s_init_controls(struct ov01a1s *ov01a1s)
+{
+	struct v4l2_ctrl_handler *ctrl_hdlr;
+	const struct ov01a1s_mode *cur_mode;
+	s64 exposure_max, h_blank;
+	u32 vblank_min, vblank_max, vblank_default;
+	int size;
+	int ret = 0;
+
+	ctrl_hdlr = &ov01a1s->ctrl_handler;
+	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8);
+	if (ret)
+		return ret;
+
+	ctrl_hdlr->lock = &ov01a1s->mutex;
+	cur_mode = ov01a1s->cur_mode;
+	size = ARRAY_SIZE(link_freq_menu_items);
+
+	ov01a1s->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr,
+						    &ov01a1s_ctrl_ops,
+						    V4L2_CID_LINK_FREQ,
+						    size - 1, 0,
+						    link_freq_menu_items);
+	if (ov01a1s->link_freq)
+		ov01a1s->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	ov01a1s->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a1s_ctrl_ops,
+						V4L2_CID_PIXEL_RATE, 0,
+						OV01A1S_SCLK, 1, OV01A1S_SCLK);
+
+	vblank_min = cur_mode->vts_min - cur_mode->height;
+	vblank_max = OV01A1S_VTS_MAX - cur_mode->height;
+	vblank_default = cur_mode->vts_def - cur_mode->height;
+	ov01a1s->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a1s_ctrl_ops,
+					    V4L2_CID_VBLANK, vblank_min,
+					    vblank_max, 1, vblank_default);
+
+	h_blank = cur_mode->hts - cur_mode->width;
+	ov01a1s->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a1s_ctrl_ops,
+					    V4L2_CID_HBLANK, h_blank, h_blank,
+					    1, h_blank);
+	if (ov01a1s->hblank)
+		ov01a1s->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov01a1s_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+			  OV01A1S_ANAL_GAIN_MIN, OV01A1S_ANAL_GAIN_MAX,
+			  OV01A1S_ANAL_GAIN_STEP, OV01A1S_ANAL_GAIN_MIN);
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov01a1s_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+			  OV01A1S_DGTL_GAIN_MIN, OV01A1S_DGTL_GAIN_MAX,
+			  OV01A1S_DGTL_GAIN_STEP, OV01A1S_DGTL_GAIN_DEFAULT);
+	exposure_max = cur_mode->vts_def - OV01A1S_EXPOSURE_MAX_MARGIN;
+	ov01a1s->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &ov01a1s_ctrl_ops,
+					      V4L2_CID_EXPOSURE,
+					      OV01A1S_EXPOSURE_MIN,
+					      exposure_max,
+					      OV01A1S_EXPOSURE_STEP,
+					      exposure_max);
+	v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov01a1s_ctrl_ops,
+				     V4L2_CID_TEST_PATTERN,
+				     ARRAY_SIZE(ov01a1s_test_pattern_menu) - 1,
+				     0, 0, ov01a1s_test_pattern_menu);
+	if (ctrl_hdlr->error)
+		return ctrl_hdlr->error;
+
+	ov01a1s->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+}
+
+static void ov01a1s_update_pad_format(const struct ov01a1s_mode *mode,
+				      struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+	fmt->field = V4L2_FIELD_NONE;
+}
+
+static int ov01a1s_start_streaming(struct ov01a1s *ov01a1s)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	const struct ov01a1s_reg_list *reg_list;
+	int link_freq_index;
+	int ret = 0;
+
+	power_ctrl_logic_set_power(1);
+	link_freq_index = ov01a1s->cur_mode->link_freq_index;
+	reg_list = &link_freq_configs[link_freq_index].reg_list;
+	ret = ov01a1s_write_reg_list(ov01a1s, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set plls");
+		return ret;
+	}
+
+	reg_list = &ov01a1s->cur_mode->reg_list;
+	ret = ov01a1s_write_reg_list(ov01a1s, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set mode");
+		return ret;
+	}
+
+	ret = __v4l2_ctrl_handler_setup(ov01a1s->sd.ctrl_handler);
+	if (ret)
+		return ret;
+
+	ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_MODE_SELECT, 1,
+				OV01A1S_MODE_STREAMING);
+	if (ret)
+		dev_err(&client->dev, "failed to start streaming");
+
+	return ret;
+}
+
+static void ov01a1s_stop_streaming(struct ov01a1s *ov01a1s)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	int ret = 0;
+
+	ret = ov01a1s_write_reg(ov01a1s, OV01A1S_REG_MODE_SELECT, 1,
+				OV01A1S_MODE_STANDBY);
+	if (ret)
+		dev_err(&client->dev, "failed to stop streaming");
+	power_ctrl_logic_set_power(0);
+}
+
+static int ov01a1s_set_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	if (ov01a1s->streaming == enable)
+		return 0;
+
+	mutex_lock(&ov01a1s->mutex);
+	if (enable) {
+		ret = pm_runtime_get_sync(&client->dev);
+		if (ret < 0) {
+			pm_runtime_put_noidle(&client->dev);
+			mutex_unlock(&ov01a1s->mutex);
+			return ret;
+		}
+
+		ret = ov01a1s_start_streaming(ov01a1s);
+		if (ret) {
+			enable = 0;
+			ov01a1s_stop_streaming(ov01a1s);
+			pm_runtime_put(&client->dev);
+		}
+	} else {
+		ov01a1s_stop_streaming(ov01a1s);
+		pm_runtime_put(&client->dev);
+	}
+
+	ov01a1s->streaming = enable;
+	mutex_unlock(&ov01a1s->mutex);
+
+	return ret;
+}
+
+static int __maybe_unused ov01a1s_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+
+	mutex_lock(&ov01a1s->mutex);
+	if (ov01a1s->streaming)
+		ov01a1s_stop_streaming(ov01a1s);
+
+	mutex_unlock(&ov01a1s->mutex);
+
+	return 0;
+}
+
+static int __maybe_unused ov01a1s_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+	int ret = 0;
+
+	mutex_lock(&ov01a1s->mutex);
+	if (!ov01a1s->streaming)
+		goto exit;
+
+	ret = ov01a1s_start_streaming(ov01a1s);
+	if (ret) {
+		ov01a1s->streaming = false;
+		ov01a1s_stop_streaming(ov01a1s);
+	}
+
+exit:
+	mutex_unlock(&ov01a1s->mutex);
+	return ret;
+}
+
+static int ov01a1s_set_format(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+	const struct ov01a1s_mode *mode;
+	s32 vblank_def, h_blank;
+
+	mode = v4l2_find_nearest_size(supported_modes,
+				      ARRAY_SIZE(supported_modes), width,
+				      height, fmt->format.width,
+				      fmt->format.height);
+
+	mutex_lock(&ov01a1s->mutex);
+	ov01a1s_update_pad_format(mode, &fmt->format);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
+		*v4l2_subdev_get_try_format(sd, sd_state, fmt->pad) = fmt->format;
+	} else {
+		ov01a1s->cur_mode = mode;
+		__v4l2_ctrl_s_ctrl(ov01a1s->link_freq, mode->link_freq_index);
+		__v4l2_ctrl_s_ctrl_int64(ov01a1s->pixel_rate, OV01A1S_SCLK);
+
+		/* Update limits and set FPS to default */
+		vblank_def = mode->vts_def - mode->height;
+		__v4l2_ctrl_modify_range(ov01a1s->vblank,
+					 mode->vts_min - mode->height,
+					 OV01A1S_VTS_MAX - mode->height, 1,
+					 vblank_def);
+		__v4l2_ctrl_s_ctrl(ov01a1s->vblank, vblank_def);
+		h_blank = mode->hts - mode->width;
+		__v4l2_ctrl_modify_range(ov01a1s->hblank, h_blank, h_blank, 1,
+					 h_blank);
+	}
+	mutex_unlock(&ov01a1s->mutex);
+
+	return 0;
+}
+
+static int ov01a1s_get_format(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+
+	mutex_lock(&ov01a1s->mutex);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt->format = *v4l2_subdev_get_try_format(&ov01a1s->sd,
+							  sd_state, fmt->pad);
+	else
+		ov01a1s_update_pad_format(ov01a1s->cur_mode, &fmt->format);
+
+	mutex_unlock(&ov01a1s->mutex);
+
+	return 0;
+}
+
+static int ov01a1s_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->index > 0)
+		return -EINVAL;
+
+	code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+
+	return 0;
+}
+
+static int ov01a1s_enum_frame_size(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->index >= ARRAY_SIZE(supported_modes))
+		return -EINVAL;
+
+	if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
+		return -EINVAL;
+
+	fse->min_width = supported_modes[fse->index].width;
+	fse->max_width = fse->min_width;
+	fse->min_height = supported_modes[fse->index].height;
+	fse->max_height = fse->min_height;
+
+	return 0;
+}
+
+static int ov01a1s_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+
+	mutex_lock(&ov01a1s->mutex);
+	ov01a1s_update_pad_format(&supported_modes[0],
+				  v4l2_subdev_get_try_format(sd, fh->state, 0));
+	mutex_unlock(&ov01a1s->mutex);
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops ov01a1s_video_ops = {
+	.s_stream = ov01a1s_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov01a1s_pad_ops = {
+	.set_fmt = ov01a1s_set_format,
+	.get_fmt = ov01a1s_get_format,
+	.enum_mbus_code = ov01a1s_enum_mbus_code,
+	.enum_frame_size = ov01a1s_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops ov01a1s_subdev_ops = {
+	.video = &ov01a1s_video_ops,
+	.pad = &ov01a1s_pad_ops,
+};
+
+static const struct media_entity_operations ov01a1s_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static const struct v4l2_subdev_internal_ops ov01a1s_internal_ops = {
+	.open = ov01a1s_open,
+};
+
+static int ov01a1s_identify_module(struct ov01a1s *ov01a1s)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov01a1s->sd);
+	int ret;
+	u32 val;
+
+	ret = ov01a1s_read_reg(ov01a1s, OV01A1S_REG_CHIP_ID, 3, &val);
+	if (ret)
+		return ret;
+
+	if (val != OV01A1S_CHIP_ID) {
+		dev_err(&client->dev, "chip id mismatch: %x!=%x",
+			OV01A1S_CHIP_ID, val);
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int ov01a1s_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov01a1s *ov01a1s = to_ov01a1s(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(sd->ctrl_handler);
+	pm_runtime_disable(&client->dev);
+	mutex_destroy(&ov01a1s->mutex);
+
+	return 0;
+}
+
+static int ov01a1s_probe(struct i2c_client *client)
+{
+	struct ov01a1s *ov01a1s;
+	int ret = 0;
+
+	if (power_ctrl_logic_set_power(1)) {
+		dev_dbg(&client->dev, "power control driver not ready.\n");
+		return -EPROBE_DEFER;
+	}
+	ov01a1s = devm_kzalloc(&client->dev, sizeof(*ov01a1s), GFP_KERNEL);
+	if (!ov01a1s) {
+		ret = -ENOMEM;
+		goto probe_error_ret;
+	}
+
+	v4l2_i2c_subdev_init(&ov01a1s->sd, client, &ov01a1s_subdev_ops);
+	ret = ov01a1s_identify_module(ov01a1s);
+	if (ret) {
+		dev_err(&client->dev, "failed to find sensor: %d", ret);
+		goto probe_error_ret;
+	}
+
+	mutex_init(&ov01a1s->mutex);
+	ov01a1s->cur_mode = &supported_modes[0];
+	ret = ov01a1s_init_controls(ov01a1s);
+	if (ret) {
+		dev_err(&client->dev, "failed to init controls: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ov01a1s->sd.internal_ops = &ov01a1s_internal_ops;
+	ov01a1s->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	ov01a1s->sd.entity.ops = &ov01a1s_subdev_entity_ops;
+	ov01a1s->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ov01a1s->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&ov01a1s->sd.entity, 1, &ov01a1s->pad);
+	if (ret) {
+		dev_err(&client->dev, "failed to init entity pads: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ret = v4l2_async_register_subdev_sensor(&ov01a1s->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto probe_error_media_entity_cleanup;
+	}
+
+	/*
+	 * Device is already turned on by i2c-core with ACPI domain PM.
+	 * Enable runtime PM and turn off the device.
+	 */
+	pm_runtime_set_active(&client->dev);
+	pm_runtime_enable(&client->dev);
+	pm_runtime_idle(&client->dev);
+
+	power_ctrl_logic_set_power(0);
+	return 0;
+
+probe_error_media_entity_cleanup:
+	media_entity_cleanup(&ov01a1s->sd.entity);
+
+probe_error_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(ov01a1s->sd.ctrl_handler);
+	mutex_destroy(&ov01a1s->mutex);
+
+probe_error_ret:
+	power_ctrl_logic_set_power(0);
+	return ret;
+}
+
+static const struct dev_pm_ops ov01a1s_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(ov01a1s_suspend, ov01a1s_resume)
+};
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id ov01a1s_acpi_ids[] = {
+	{ "OVTI01AS" },
+	{}
+};
+
+MODULE_DEVICE_TABLE(acpi, ov01a1s_acpi_ids);
+#endif
+
+static struct i2c_driver ov01a1s_i2c_driver = {
+	.driver = {
+		.name = "ov01a1s",
+		.pm = &ov01a1s_pm_ops,
+		.acpi_match_table = ACPI_PTR(ov01a1s_acpi_ids),
+	},
+	.probe_new = ov01a1s_probe,
+	.remove = ov01a1s_remove,
+};
+
+module_i2c_driver(ov01a1s_i2c_driver);
+
+MODULE_AUTHOR("Xu, Chongyang <chongyang.xu@intel.com>");
+MODULE_AUTHOR("Lai, Jim <jim.lai@intel.com>");
+MODULE_AUTHOR("Qiu, Tianshu <tian.shu.qiu@intel.com>");
+MODULE_AUTHOR("Shawn Tu <shawnx.tu@intel.com>");
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_DESCRIPTION("OmniVision OV01A1S sensor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov02c10.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov02c10.c
@@ -0,0 +1,1044 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2022 Intel Corporation.
+
+#include <asm/unaligned.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/version.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <linux/vsc.h>
+
+#define OV02C10_LINK_FREQ_400MHZ	400000000ULL
+#define OV02C10_SCLK			80000000LL
+#define OV02C10_MCLK			19200000
+#define OV02C10_DATA_LANES		1
+#define OV02C10_RGB_DEPTH		10
+
+#define OV02C10_REG_CHIP_ID		0x300a
+#define OV02C10_CHIP_ID			0x560243
+
+#define OV02C10_REG_MODE_SELECT		0x0100
+#define OV02C10_MODE_STANDBY		0x00
+#define OV02C10_MODE_STREAMING		0x01
+
+/* vertical-timings from sensor */
+#define OV02C10_REG_VTS			0x380e
+#define OV02C10_VTS_DEF			0x048c
+#define OV02C10_VTS_MIN			0x048c
+#define OV02C10_VTS_MAX			0x7fff
+
+/* Exposure controls from sensor */
+#define OV02C10_REG_EXPOSURE		0x3501
+#define OV02C10_EXPOSURE_MIN		4
+#define OV02C10_EXPOSURE_MAX_MARGIN	8
+#define OV02C10_EXPOSURE_STEP		1
+
+/* Analog gain controls from sensor */
+#define OV02C10_REG_ANALOG_GAIN		0x3508
+#define OV02C10_ANAL_GAIN_MIN		0x10
+#define OV02C10_ANAL_GAIN_MAX		0xf8
+#define OV02C10_ANAL_GAIN_STEP		1
+#define OV02C10_ANAL_GAIN_DEFAULT	0x80
+
+/* Digital gain controls from sensor */
+#define OV02C10_REG_DIGILAL_GAIN	0x350a
+#define OV02C10_DGTL_GAIN_MIN		0x0400
+#define OV02C10_DGTL_GAIN_MAX		0x3fff
+#define OV02C10_DGTL_GAIN_STEP		1
+#define OV02C10_DGTL_GAIN_DEFAULT	0x0400
+
+/* Test Pattern Control */
+#define OV02C10_REG_TEST_PATTERN		0x4503
+#define OV02C10_TEST_PATTERN_ENABLE	BIT(7)
+#define OV02C10_TEST_PATTERN_BAR_SHIFT	0
+
+enum {
+	OV02C10_LINK_FREQ_400MHZ_INDEX,
+};
+
+struct ov02c10_reg {
+	u16 address;
+	u8 val;
+};
+
+struct ov02c10_reg_list {
+	u32 num_of_regs;
+	const struct ov02c10_reg *regs;
+};
+
+struct ov02c10_link_freq_config {
+	const struct ov02c10_reg_list reg_list;
+};
+
+struct ov02c10_mode {
+	/* Frame width in pixels */
+	u32 width;
+
+	/* Frame height in pixels */
+	u32 height;
+
+	/* Horizontal timining size */
+	u32 hts;
+
+	/* Default vertical timining size */
+	u32 vts_def;
+
+	/* Min vertical timining size */
+	u32 vts_min;
+
+	/* Link frequency needed for this resolution */
+	u32 link_freq_index;
+
+	/* Sensor register settings for this resolution */
+	const struct ov02c10_reg_list reg_list;
+};
+
+static const struct ov02c10_reg mipi_data_rate_960mbps[] = {
+};
+
+static const struct ov02c10_reg sensor_1932x1092_1lane_30fps_setting[] = {
+	// 1932x1092_GRBG_MIPI_MCLK19.2MHz_30fps_1Lane
+	{0x0301, 0x08},
+	// {0x0303, 0x06},
+	{0x0304, 0x01},
+	// {0x0305, 0xe0},
+	{0x0313, 0x40},
+	{0x031c, 0x4f},
+	{0x301b, 0xd2},
+	{0x3020, 0x97},
+	{0x3022, 0x01},
+	{0x3026, 0xb4},
+	{0x3027, 0xe1},
+	{0x303b, 0x00},
+	{0x303c, 0x4f},
+	{0x303d, 0xe6},
+	{0x303e, 0x00},
+	{0x303f, 0x03},
+	{0x3021, 0x23},
+	{0x3501, 0x04},
+	{0x3502, 0x6c},
+	{0x3504, 0x0c},
+	{0x3507, 0x00},
+	{0x3508, 0x08},
+	{0x3509, 0x00},
+	{0x350a, 0x01},
+	{0x350b, 0x00},
+	{0x350c, 0x41},
+	{0x3600, 0x84},
+	{0x3611, 0x1b},
+	{0x3613, 0x78},
+	{0x3623, 0x00},
+	{0x3632, 0xa0},
+	{0x3642, 0xe8},
+	{0x364c, 0x70},
+	{0x365f, 0x0f},
+	{0x3708, 0x30},
+	{0x3714, 0x24},
+	{0x3725, 0x02},
+	{0x3737, 0x08},
+	{0x3739, 0x28},
+	{0x3749, 0x32},
+	{0x374a, 0x32},
+	{0x374b, 0x32},
+	{0x374c, 0x32},
+	{0x374d, 0x81},
+	{0x374e, 0x81},
+	{0x374f, 0x81},
+	{0x3752, 0x36},
+	{0x3753, 0x36},
+	{0x3754, 0x36},
+	{0x3761, 0x00},
+	{0x376c, 0x81},
+	{0x377c, 0x81},
+	{0x377d, 0x81},
+	{0x377e, 0x81},
+	{0x37a0, 0x44},
+	{0x37a6, 0x44},
+	{0x37aa, 0x0d},
+	{0x37ae, 0x00},
+	{0x37cb, 0x03},
+	{0x37cc, 0x01},
+	{0x37d8, 0x02},
+	{0x37d9, 0x10},
+	{0x37e1, 0x10},
+	{0x37e2, 0x18},
+	{0x37e3, 0x08},
+	{0x37e4, 0x08},
+	{0x37e5, 0x02},
+	{0x37e6, 0x08},
+	{0x3800, 0x00},
+	{0x3801, 0x00},
+	{0x3802, 0x00},
+	// {0x3803, 0x04},
+	// {0x3804, 0x07},
+	// {0x3805, 0x8f},
+	// {0x3806, 0x04},
+	// {0x3807, 0x43},
+	// {0x3808, 0x07},
+	// {0x3809, 0x80},
+	// {0x380a, 0x04},
+	// {0x380b, 0x38},
+	// {0x380c, 0x04},
+	// {0x380d, 0x74},
+	// {0x380e, 0x04},
+	// {0x380f, 0x8c},
+	// {0x3810, 0x00},
+	// {0x3811, 0x07},
+	// {0x3812, 0x00},
+	// {0x3813, 0x04},
+	{0x3814, 0x01},
+	{0x3815, 0x01},
+	{0x3816, 0x01},
+	{0x3817, 0x01},
+	{0x3820, 0xa8},
+	{0x3821, 0x00},
+	{0x3822, 0x80},
+	{0x3823, 0x08},
+	{0x3824, 0x00},
+	{0x3825, 0x20},
+	{0x3826, 0x00},
+	{0x3827, 0x08},
+	{0x382a, 0x00},
+	{0x382b, 0x08},
+	{0x382d, 0x00},
+	{0x382e, 0x00},
+	{0x382f, 0x23},
+	{0x3834, 0x00},
+	{0x3839, 0x00},
+	{0x383a, 0xd1},
+	{0x383e, 0x03},
+	{0x393d, 0x29},
+	{0x393f, 0x6e},
+	{0x394b, 0x01},
+	{0x394c, 0x01},
+	{0x394d, 0x01},
+	{0x394e, 0x01},
+	{0x394f, 0x01},
+	{0x3950, 0x01},
+	{0x3951, 0x01},
+	{0x3952, 0x01},
+	{0x3953, 0x01},
+	{0x3954, 0x01},
+	{0x3955, 0x01},
+	{0x3956, 0x01},
+	{0x3957, 0x0e},
+	{0x3958, 0x08},
+	{0x3959, 0x08},
+	{0x395a, 0x08},
+	{0x395b, 0x00},
+	{0x395c, 0x00},
+	{0x395d, 0x00},
+	{0x395e, 0x00},
+	{0x395f, 0x00},
+	{0x395f, 0x00},
+	{0x3960, 0x00},
+	{0x3961, 0x00},
+	{0x3962, 0x00},
+	{0x3963, 0x00},
+	{0x3964, 0x00},
+	{0x3965, 0x00},
+	{0x3966, 0x00},
+	{0x3967, 0x00},
+	{0x3968, 0x01},
+	{0x3969, 0x01},
+	{0x396a, 0x01},
+	{0x396b, 0x01},
+	{0x396c, 0x00},
+	{0x396d, 0xf0},
+	{0x396e, 0x11},
+	{0x396f, 0x00},
+	{0x3970, 0x37},
+	{0x3971, 0x37},
+	{0x3972, 0x37},
+	{0x3973, 0x37},
+	{0x3974, 0x00},
+	{0x3975, 0x3c},
+	{0x3976, 0x3c},
+	{0x3977, 0x3c},
+	{0x3978, 0x3c},
+	{0x3c00, 0x0f},
+	{0x3c20, 0x01},
+	{0x3c21, 0x08},
+	{0x3f00, 0x8b},
+	{0x3f02, 0x0f},
+	{0x4000, 0xc3},
+	{0x4001, 0xe0},
+	{0x4002, 0x00},
+	{0x4003, 0x40},
+	{0x4008, 0x04},
+	{0x4009, 0x23},
+	{0x400a, 0x04},
+	{0x400b, 0x01},
+	{0x4077, 0x06},
+	{0x4078, 0x00},
+	{0x4079, 0x1a},
+	{0x407a, 0x7f},
+	{0x407b, 0x01},
+	{0x4080, 0x03},
+	{0x4081, 0x84},
+	{0x4308, 0x03},
+	{0x4309, 0xff},
+	{0x430d, 0x00},
+	{0x4806, 0x00},
+	{0x4813, 0x00},
+	{0x4837, 0x10},
+	{0x4857, 0x05},
+	{0x4500, 0x07},
+	{0x4501, 0x00},
+	{0x4503, 0x00},
+	{0x450a, 0x04},
+	{0x450e, 0x00},
+	{0x450f, 0x00},
+	{0x4800, 0x24},
+	{0x4900, 0x00},
+	{0x4901, 0x00},
+	{0x4902, 0x01},
+	{0x5000, 0xf5},
+	{0x5001, 0x50},
+	{0x5006, 0x00},
+	{0x5080, 0x40},
+	{0x5181, 0x2b},
+	{0x5202, 0xa3},
+	{0x5206, 0x01},
+	{0x5207, 0x00},
+	{0x520a, 0x01},
+	{0x520b, 0x00},
+	// {0x3016, 0x32},
+	{0x365d, 0x00},
+	{0x4815, 0x40},
+	{0x4816, 0x12},
+	{0x4f00, 0x01},
+	{0x396c, 0x10},
+	{0x3603, 0x08},
+	{0x395b, 0x13},
+	{0x395c, 0x09},
+	{0x395d, 0x05},
+	{0x395e, 0x02},
+	{0x3610, 0x57},
+	{0x394e, 0x0b},
+	{0x394d, 0x08},
+	{0x394c, 0x06},
+	{0x394b, 0x06},
+	// key setting for MCLK=19.2MCLK 1932x1092 GRBG 1 lane 30fps
+	{0x0303, 0x05},
+	{0x0305, 0x90},
+	{0x0316, 0x90},
+	{0x3016, 0x12},
+	{0x3803, 0x00},
+	{0x3804, 0x07},
+	{0x3805, 0x8f},
+	{0x3806, 0x04},
+	{0x3807, 0x47},
+	{0x3808, 0x07},
+	{0x3809, 0x8c},
+	{0x380a, 0x04},
+	{0x380b, 0x44},
+	{0x380c, 0x08},
+	{0x380d, 0xe8},
+	{0x380e, 0x04},
+	{0x380f, 0x8c},
+	{0x3810, 0x00},
+	{0x3811, 0x03},
+	{0x3812, 0x00},
+	{0x3813, 0x03},
+};
+
+static const char * const ov02c10_test_pattern_menu[] = {
+	"Disabled",
+	"Color Bar",
+	"Top-Bottom Darker Color Bar",
+	"Right-Left Darker Color Bar",
+	"Color Bar type 4",
+};
+
+static const s64 link_freq_menu_items[] = {
+	OV02C10_LINK_FREQ_400MHZ,
+};
+
+static const struct ov02c10_link_freq_config link_freq_configs[] = {
+	[OV02C10_LINK_FREQ_400MHZ_INDEX] = {
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(mipi_data_rate_960mbps),
+			.regs = mipi_data_rate_960mbps,
+		}
+	},
+};
+
+static const struct ov02c10_mode supported_modes[] = {
+	{
+		.width = 1932,
+		.height = 1092,
+		.hts = 2280,
+		.vts_def = OV02C10_VTS_DEF,
+		.vts_min = OV02C10_VTS_MIN,
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(sensor_1932x1092_1lane_30fps_setting),
+			.regs = sensor_1932x1092_1lane_30fps_setting,
+		},
+		.link_freq_index = OV02C10_LINK_FREQ_400MHZ_INDEX,
+	},
+};
+
+struct ov02c10 {
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	/* V4L2 Controls */
+	struct v4l2_ctrl *link_freq;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *exposure;
+	struct v4l2_ctrl *privacy_status;
+	/* Current mode */
+	const struct ov02c10_mode *cur_mode;
+
+	/* To serialize asynchronus callbacks */
+	struct mutex mutex;
+
+	/* Streaming on/off */
+	bool streaming;
+};
+
+static inline struct ov02c10 *to_ov02c10(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct ov02c10, sd);
+}
+
+static int ov02c10_read_reg(struct ov02c10 *ov02c10, u16 reg, u16 len, u32 *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	struct i2c_msg msgs[2];
+	u8 addr_buf[2];
+	u8 data_buf[4] = {0};
+	int ret = 0;
+
+	if (len > sizeof(data_buf))
+		return -EINVAL;
+
+	put_unaligned_be16(reg, addr_buf);
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = sizeof(addr_buf);
+	msgs[0].buf = addr_buf;
+	msgs[1].addr = client->addr;
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].len = len;
+	msgs[1].buf = &data_buf[sizeof(data_buf) - len];
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+
+	if (ret != ARRAY_SIZE(msgs))
+		return ret < 0 ? ret : -EIO;
+
+	*val = get_unaligned_be32(data_buf);
+
+	return 0;
+}
+
+static int ov02c10_write_reg(struct ov02c10 *ov02c10, u16 reg, u16 len, u32 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	u8 buf[6];
+	int ret = 0;
+
+	if (len > 4)
+		return -EINVAL;
+
+	put_unaligned_be16(reg, buf);
+	put_unaligned_be32(val << 8 * (4 - len), buf + 2);
+
+	ret = i2c_master_send(client, buf, len + 2);
+	if (ret != len + 2)
+		return ret < 0 ? ret : -EIO;
+
+	return 0;
+}
+
+static int ov02c10_write_reg_list(struct ov02c10 *ov02c10,
+				  const struct ov02c10_reg_list *r_list)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	unsigned int i;
+	int ret = 0;
+
+	for (i = 0; i < r_list->num_of_regs; i++) {
+		ret = ov02c10_write_reg(ov02c10, r_list->regs[i].address, 1,
+					r_list->regs[i].val);
+		if (ret) {
+			dev_err_ratelimited(&client->dev,
+					    "write reg 0x%4.4x return err = %d",
+					    r_list->regs[i].address, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int ov02c10_test_pattern(struct ov02c10 *ov02c10, u32 pattern)
+{
+	if (pattern)
+		pattern = (pattern - 1) << OV02C10_TEST_PATTERN_BAR_SHIFT |
+			  OV02C10_TEST_PATTERN_ENABLE;
+
+	return ov02c10_write_reg(ov02c10, OV02C10_REG_TEST_PATTERN, 1, pattern);
+}
+
+static int ov02c10_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ov02c10 *ov02c10 = container_of(ctrl->handler,
+					     struct ov02c10, ctrl_handler);
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	s64 exposure_max;
+	int ret = 0;
+
+	/* Propagate change of current control to all related controls */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Update max exposure while meeting expected vblanking */
+		exposure_max = ov02c10->cur_mode->height + ctrl->val -
+			       OV02C10_EXPOSURE_MAX_MARGIN;
+		__v4l2_ctrl_modify_range(ov02c10->exposure,
+					 ov02c10->exposure->minimum,
+					 exposure_max, ov02c10->exposure->step,
+					 exposure_max);
+	}
+
+	/* V4L2 controls values will be applied only when power is already up */
+	if (!pm_runtime_get_if_in_use(&client->dev))
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = ov02c10_write_reg(ov02c10, OV02C10_REG_ANALOG_GAIN, 2,
+					ctrl->val << 4);
+		break;
+
+	case V4L2_CID_DIGITAL_GAIN:
+		ret = ov02c10_write_reg(ov02c10, OV02C10_REG_DIGILAL_GAIN, 3,
+					ctrl->val << 6);
+		break;
+
+	case V4L2_CID_EXPOSURE:
+		ret = ov02c10_write_reg(ov02c10, OV02C10_REG_EXPOSURE, 2,
+					ctrl->val);
+		break;
+
+	case V4L2_CID_VBLANK:
+		ret = ov02c10_write_reg(ov02c10, OV02C10_REG_VTS, 2,
+					ov02c10->cur_mode->height + ctrl->val);
+		break;
+
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov02c10_test_pattern(ov02c10, ctrl->val);
+		break;
+
+	case V4L2_CID_PRIVACY:
+		dev_dbg(&client->dev, "set privacy to %d", ctrl->val);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	pm_runtime_put(&client->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops ov02c10_ctrl_ops = {
+	.s_ctrl = ov02c10_set_ctrl,
+};
+
+static int ov02c10_init_controls(struct ov02c10 *ov02c10)
+{
+	struct v4l2_ctrl_handler *ctrl_hdlr;
+	const struct ov02c10_mode *cur_mode;
+	s64 exposure_max, h_blank;
+	u32 vblank_min, vblank_max, vblank_default;
+	int size;
+	int ret = 0;
+
+	ctrl_hdlr = &ov02c10->ctrl_handler;
+	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 9);
+	if (ret)
+		return ret;
+
+	ctrl_hdlr->lock = &ov02c10->mutex;
+	cur_mode = ov02c10->cur_mode;
+	size = ARRAY_SIZE(link_freq_menu_items);
+
+	ov02c10->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr,
+						    &ov02c10_ctrl_ops,
+						    V4L2_CID_LINK_FREQ,
+						    size - 1, 0,
+						    link_freq_menu_items);
+	if (ov02c10->link_freq)
+		ov02c10->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	ov02c10->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops,
+						V4L2_CID_PIXEL_RATE, 0,
+						OV02C10_SCLK, 1, OV02C10_SCLK);
+
+	vblank_min = cur_mode->vts_min - cur_mode->height;
+	vblank_max = OV02C10_VTS_MAX - cur_mode->height;
+	vblank_default = cur_mode->vts_def - cur_mode->height;
+	ov02c10->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops,
+					    V4L2_CID_VBLANK, vblank_min,
+					    vblank_max, 1, vblank_default);
+
+	h_blank = cur_mode->hts - cur_mode->width;
+	ov02c10->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops,
+					    V4L2_CID_HBLANK, h_blank, h_blank,
+					    1, h_blank);
+	if (ov02c10->hblank)
+		ov02c10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	ov02c10->privacy_status = v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops,
+								V4L2_CID_PRIVACY, 0, 1, 1, 0);
+
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+			  OV02C10_ANAL_GAIN_MIN, OV02C10_ANAL_GAIN_MAX,
+			  OV02C10_ANAL_GAIN_STEP, OV02C10_ANAL_GAIN_DEFAULT);
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+			  OV02C10_DGTL_GAIN_MIN, OV02C10_DGTL_GAIN_MAX,
+			  OV02C10_DGTL_GAIN_STEP, OV02C10_DGTL_GAIN_DEFAULT);
+	exposure_max = cur_mode->vts_def - OV02C10_EXPOSURE_MAX_MARGIN;
+	ov02c10->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &ov02c10_ctrl_ops,
+					      V4L2_CID_EXPOSURE,
+					      OV02C10_EXPOSURE_MIN,
+					      exposure_max,
+					      OV02C10_EXPOSURE_STEP,
+					      exposure_max);
+	v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov02c10_ctrl_ops,
+				     V4L2_CID_TEST_PATTERN,
+				     ARRAY_SIZE(ov02c10_test_pattern_menu) - 1,
+				     0, 0, ov02c10_test_pattern_menu);
+	if (ctrl_hdlr->error)
+		return ctrl_hdlr->error;
+
+	ov02c10->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+}
+
+static void ov02c10_update_pad_format(const struct ov02c10_mode *mode,
+				      struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+	fmt->field = V4L2_FIELD_NONE;
+}
+
+static void ov02c10_vsc_privacy_callback(void *handle,
+				       enum vsc_privacy_status status)
+{
+	struct ov02c10 *ov02c10 = handle;
+
+	v4l2_ctrl_s_ctrl(ov02c10->privacy_status, !status);
+}
+
+static int ov02c10_start_streaming(struct ov02c10 *ov02c10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	const struct ov02c10_reg_list *reg_list;
+	int link_freq_index;
+	int ret = 0;
+	struct vsc_mipi_config conf;
+	struct vsc_camera_status status;
+
+	conf.lane_num = OV02C10_DATA_LANES;
+	/* frequency unit 100k */
+	conf.freq = OV02C10_LINK_FREQ_400MHZ / 100000;
+	ret = vsc_acquire_camera_sensor(&conf, ov02c10_vsc_privacy_callback,
+									ov02c10, &status);
+	if (ret) {
+		dev_err(&client->dev, "Acquire VSC failed");
+		return ret;
+	}
+	__v4l2_ctrl_s_ctrl(ov02c10->privacy_status, !(status.status));
+	link_freq_index = ov02c10->cur_mode->link_freq_index;
+	reg_list = &link_freq_configs[link_freq_index].reg_list;
+	ret = ov02c10_write_reg_list(ov02c10, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set plls");
+		return ret;
+	}
+
+	reg_list = &ov02c10->cur_mode->reg_list;
+	ret = ov02c10_write_reg_list(ov02c10, reg_list);
+	if (ret) {
+		dev_err(&client->dev, "failed to set mode");
+		return ret;
+	}
+
+	ret = __v4l2_ctrl_handler_setup(ov02c10->sd.ctrl_handler);
+	if (ret)
+		return ret;
+
+	ret = ov02c10_write_reg(ov02c10, OV02C10_REG_MODE_SELECT, 1,
+				OV02C10_MODE_STREAMING);
+	if (ret)
+		dev_err(&client->dev, "failed to start streaming");
+
+	return ret;
+}
+
+static void ov02c10_stop_streaming(struct ov02c10 *ov02c10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	int ret = 0;
+	struct vsc_camera_status status;
+
+	ret = ov02c10_write_reg(ov02c10, OV02C10_REG_MODE_SELECT, 1,
+				OV02C10_MODE_STANDBY);
+	if (ret)
+		dev_err(&client->dev, "failed to stop streaming");
+	ret = vsc_release_camera_sensor(&status);
+	if (ret)
+		dev_err(&client->dev, "Release VSC failed");
+}
+
+static int ov02c10_set_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	if (ov02c10->streaming == enable)
+		return 0;
+
+	mutex_lock(&ov02c10->mutex);
+	if (enable) {
+		ret = pm_runtime_get_sync(&client->dev);
+		if (ret < 0) {
+			pm_runtime_put_noidle(&client->dev);
+			mutex_unlock(&ov02c10->mutex);
+			return ret;
+		}
+
+		ret = ov02c10_start_streaming(ov02c10);
+		if (ret) {
+			enable = 0;
+			ov02c10_stop_streaming(ov02c10);
+			pm_runtime_put(&client->dev);
+		}
+	} else {
+		ov02c10_stop_streaming(ov02c10);
+		pm_runtime_put(&client->dev);
+	}
+
+	ov02c10->streaming = enable;
+	mutex_unlock(&ov02c10->mutex);
+
+	return ret;
+}
+
+static int __maybe_unused ov02c10_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+
+	mutex_lock(&ov02c10->mutex);
+	if (ov02c10->streaming)
+		ov02c10_stop_streaming(ov02c10);
+
+	mutex_unlock(&ov02c10->mutex);
+
+	return 0;
+}
+
+static int __maybe_unused ov02c10_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+	int ret = 0;
+
+	mutex_lock(&ov02c10->mutex);
+	if (!ov02c10->streaming)
+		goto exit;
+
+	ret = ov02c10_start_streaming(ov02c10);
+	if (ret) {
+		ov02c10->streaming = false;
+		ov02c10_stop_streaming(ov02c10);
+	}
+
+exit:
+	mutex_unlock(&ov02c10->mutex);
+	return ret;
+}
+
+static int ov02c10_set_format(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+	const struct ov02c10_mode *mode;
+	s32 vblank_def, h_blank;
+
+	mode = v4l2_find_nearest_size(supported_modes,
+				      ARRAY_SIZE(supported_modes), width,
+				      height, fmt->format.width,
+				      fmt->format.height);
+
+	mutex_lock(&ov02c10->mutex);
+	ov02c10_update_pad_format(mode, &fmt->format);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
+		*v4l2_subdev_get_try_format(sd, sd_state, fmt->pad) = fmt->format;
+	} else {
+		ov02c10->cur_mode = mode;
+		__v4l2_ctrl_s_ctrl(ov02c10->link_freq, mode->link_freq_index);
+		__v4l2_ctrl_s_ctrl_int64(ov02c10->pixel_rate, OV02C10_SCLK);
+
+		/* Update limits and set FPS to default */
+		vblank_def = mode->vts_def - mode->height;
+		__v4l2_ctrl_modify_range(ov02c10->vblank,
+					 mode->vts_min - mode->height,
+					 OV02C10_VTS_MAX - mode->height, 1,
+					 vblank_def);
+		__v4l2_ctrl_s_ctrl(ov02c10->vblank, vblank_def);
+		h_blank = mode->hts - mode->width;
+		__v4l2_ctrl_modify_range(ov02c10->hblank, h_blank, h_blank, 1,
+					 h_blank);
+	}
+	mutex_unlock(&ov02c10->mutex);
+
+	return 0;
+}
+
+static int ov02c10_get_format(struct v4l2_subdev *sd,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+
+	mutex_lock(&ov02c10->mutex);
+	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
+		fmt->format = *v4l2_subdev_get_try_format(&ov02c10->sd,
+							  sd_state, fmt->pad);
+	else
+		ov02c10_update_pad_format(ov02c10->cur_mode, &fmt->format);
+
+	mutex_unlock(&ov02c10->mutex);
+
+	return 0;
+}
+
+static int ov02c10_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->index > 0)
+		return -EINVAL;
+
+	code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+
+	return 0;
+}
+
+static int ov02c10_enum_frame_size(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->index >= ARRAY_SIZE(supported_modes))
+		return -EINVAL;
+
+	if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
+		return -EINVAL;
+
+	fse->min_width = supported_modes[fse->index].width;
+	fse->max_width = fse->min_width;
+	fse->min_height = supported_modes[fse->index].height;
+	fse->max_height = fse->min_height;
+
+	return 0;
+}
+
+static int ov02c10_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+
+	mutex_lock(&ov02c10->mutex);
+	ov02c10_update_pad_format(&supported_modes[0],
+				  v4l2_subdev_get_try_format(sd, fh->state, 0));
+	mutex_unlock(&ov02c10->mutex);
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops ov02c10_video_ops = {
+	.s_stream = ov02c10_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov02c10_pad_ops = {
+	.set_fmt = ov02c10_set_format,
+	.get_fmt = ov02c10_get_format,
+	.enum_mbus_code = ov02c10_enum_mbus_code,
+	.enum_frame_size = ov02c10_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops ov02c10_subdev_ops = {
+	.video = &ov02c10_video_ops,
+	.pad = &ov02c10_pad_ops,
+};
+
+static const struct media_entity_operations ov02c10_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static const struct v4l2_subdev_internal_ops ov02c10_internal_ops = {
+	.open = ov02c10_open,
+};
+
+static int ov02c10_identify_module(struct ov02c10 *ov02c10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02c10->sd);
+	int ret;
+	u32 val;
+
+	ret = ov02c10_read_reg(ov02c10, OV02C10_REG_CHIP_ID, 3, &val);
+	if (ret)
+		return ret;
+
+	if (val != OV02C10_CHIP_ID) {
+		dev_err(&client->dev, "chip id mismatch: %x!=%x",
+			OV02C10_CHIP_ID, val);
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int ov02c10_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov02c10 *ov02c10 = to_ov02c10(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(sd->ctrl_handler);
+	pm_runtime_disable(&client->dev);
+	mutex_destroy(&ov02c10->mutex);
+
+	return 0;
+}
+
+static int ov02c10_probe(struct i2c_client *client)
+{
+	struct ov02c10 *ov02c10;
+	int ret = 0;
+	struct vsc_mipi_config conf;
+	struct vsc_camera_status status;
+
+	conf.lane_num = OV02C10_DATA_LANES;
+	/* frequency unit 100k */
+	conf.freq = OV02C10_LINK_FREQ_400MHZ / 100000;
+	ret = vsc_acquire_camera_sensor(&conf, NULL, NULL, &status);
+	if (ret == -EAGAIN) {
+		dev_dbg(&client->dev, "VSC not ready, will re-probe");
+		return -EPROBE_DEFER;
+	} else if (ret) {
+		dev_err(&client->dev, "Acquire VSC failed");
+		return ret;
+	}
+	ov02c10 = devm_kzalloc(&client->dev, sizeof(*ov02c10), GFP_KERNEL);
+	if (!ov02c10) {
+		ret = -ENOMEM;
+		goto probe_error_ret;
+	}
+
+	v4l2_i2c_subdev_init(&ov02c10->sd, client, &ov02c10_subdev_ops);
+
+	ret = ov02c10_identify_module(ov02c10);
+	if (ret) {
+		dev_err(&client->dev, "failed to find sensor: %d", ret);
+		goto probe_error_ret;
+	}
+
+	mutex_init(&ov02c10->mutex);
+	ov02c10->cur_mode = &supported_modes[0];
+	ret = ov02c10_init_controls(ov02c10);
+	if (ret) {
+		dev_err(&client->dev, "failed to init controls: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ov02c10->sd.internal_ops = &ov02c10_internal_ops;
+	ov02c10->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	ov02c10->sd.entity.ops = &ov02c10_subdev_entity_ops;
+	ov02c10->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ov02c10->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&ov02c10->sd.entity, 1, &ov02c10->pad);
+	if (ret) {
+		dev_err(&client->dev, "failed to init entity pads: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ret = v4l2_async_register_subdev_sensor(&ov02c10->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto probe_error_media_entity_cleanup;
+	}
+
+	vsc_release_camera_sensor(&status);
+	/*
+	 * Device is already turned on by i2c-core with ACPI domain PM.
+	 * Enable runtime PM and turn off the device.
+	 */
+	pm_runtime_set_active(&client->dev);
+	pm_runtime_enable(&client->dev);
+	pm_runtime_idle(&client->dev);
+
+	return 0;
+
+probe_error_media_entity_cleanup:
+	media_entity_cleanup(&ov02c10->sd.entity);
+
+probe_error_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(ov02c10->sd.ctrl_handler);
+	mutex_destroy(&ov02c10->mutex);
+
+probe_error_ret:
+	vsc_release_camera_sensor(&status);
+	return ret;
+}
+
+static const struct dev_pm_ops ov02c10_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(ov02c10_suspend, ov02c10_resume)
+};
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id ov02c10_acpi_ids[] = {
+	{"OVTI02C1"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(acpi, ov02c10_acpi_ids);
+#endif
+
+static struct i2c_driver ov02c10_i2c_driver = {
+	.driver = {
+		.name = "ov02c10",
+		.pm = &ov02c10_pm_ops,
+		.acpi_match_table = ACPI_PTR(ov02c10_acpi_ids),
+	},
+	.probe_new = ov02c10_probe,
+	.remove = ov02c10_remove,
+};
+
+module_i2c_driver(ov02c10_i2c_driver);
+
+MODULE_AUTHOR("Hao Yao <hao.yao@intel.com>");
+MODULE_DESCRIPTION("OmniVision OV02C10 sensor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov2680.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov2680.c
@@ -54,6 +54,9 @@
 #define OV2680_WIDTH_MAX		1600
 #define OV2680_HEIGHT_MAX		1200
 
+#define OV2680_DEFAULT_WIDTH			800
+#define OV2680_DEFAULT_HEIGHT			600
+
 enum ov2680_mode_id {
 	OV2680_MODE_QUXGA_800_600,
 	OV2680_MODE_720P_1280_720,
@@ -85,15 +88,8 @@
 
 struct ov2680_ctrls {
 	struct v4l2_ctrl_handler handler;
-	struct {
-		struct v4l2_ctrl *auto_exp;
-		struct v4l2_ctrl *exposure;
-	};
-	struct {
-		struct v4l2_ctrl *auto_gain;
-		struct v4l2_ctrl *gain;
-	};
-
+	struct v4l2_ctrl *exposure;
+	struct v4l2_ctrl *gain;
 	struct v4l2_ctrl *hflip;
 	struct v4l2_ctrl *vflip;
 	struct v4l2_ctrl *test_pattern;
@@ -143,6 +139,7 @@
 	{0x380e, 0x02}, {0x380f, 0x84}, {0x3811, 0x04}, {0x3813, 0x04},
 	{0x3814, 0x31}, {0x3815, 0x31}, {0x3820, 0xc0}, {0x4008, 0x00},
 	{0x4009, 0x03}, {0x4837, 0x1e}, {0x3501, 0x4e}, {0x3502, 0xe0},
+	{0x3503, 0x03},
 };
 
 static const struct reg_value ov2680_setting_30fps_720P_1280_720[] = {
@@ -321,70 +318,62 @@
 	usleep_range(5000, 10000);
 }
 
-static int ov2680_bayer_order(struct ov2680_dev *sensor)
+static void ov2680_set_bayer_order(struct ov2680_dev *sensor,
+				   struct v4l2_mbus_framefmt *fmt)
 {
-	u32 format1;
-	u32 format2;
-	u32 hv_flip;
-	int ret;
-
-	ret = ov2680_read_reg(sensor, OV2680_REG_FORMAT1, &format1);
-	if (ret < 0)
-		return ret;
-
-	ret = ov2680_read_reg(sensor, OV2680_REG_FORMAT2, &format2);
-	if (ret < 0)
-		return ret;
+	int hv_flip = 0;
 
-	hv_flip = (format2 & BIT(2)  << 1) | (format1 & BIT(2));
+	if (sensor->ctrls.vflip && sensor->ctrls.vflip->val)
+		hv_flip += 1;
 
-	sensor->fmt.code = ov2680_hv_flip_bayer_order[hv_flip];
+	if (sensor->ctrls.hflip && sensor->ctrls.hflip->val)
+		hv_flip += 2;
 
-	return 0;
+	fmt->code = ov2680_hv_flip_bayer_order[hv_flip];
 }
 
-static int ov2680_vflip_enable(struct ov2680_dev *sensor)
+static void ov2680_fill_format(struct ov2680_dev *sensor,
+			       struct v4l2_mbus_framefmt *fmt,
+			       unsigned int width, unsigned int height)
 {
-	int ret;
-
-	ret = ov2680_mod_reg(sensor, OV2680_REG_FORMAT1, BIT(2), BIT(2));
-	if (ret < 0)
-		return ret;
-
-	return ov2680_bayer_order(sensor);
+	memset(fmt, 0, sizeof(*fmt));
+	fmt->width = width;
+	fmt->height = height;
+	fmt->field = V4L2_FIELD_NONE;
+	fmt->colorspace = V4L2_COLORSPACE_SRGB;
+	ov2680_set_bayer_order(sensor, fmt);
 }
 
-static int ov2680_vflip_disable(struct ov2680_dev *sensor)
+static int ov2680_set_vflip(struct ov2680_dev *sensor, s32 val)
 {
 	int ret;
 
-	ret = ov2680_mod_reg(sensor, OV2680_REG_FORMAT1, BIT(2), BIT(0));
-	if (ret < 0)
-		return ret;
-
-	return ov2680_bayer_order(sensor);
-}
-
-static int ov2680_hflip_enable(struct ov2680_dev *sensor)
-{
-	int ret;
+	if (sensor->is_streaming)
+		return -EBUSY;
 
-	ret = ov2680_mod_reg(sensor, OV2680_REG_FORMAT2, BIT(2), BIT(2));
+	ret = ov2680_mod_reg(sensor, OV2680_REG_FORMAT1,
+			     BIT(2), val ? BIT(2) : 0);
 	if (ret < 0)
 		return ret;
 
-	return ov2680_bayer_order(sensor);
+	ov2680_set_bayer_order(sensor, &sensor->fmt);
+	return 0;
 }
 
-static int ov2680_hflip_disable(struct ov2680_dev *sensor)
+static int ov2680_set_hflip(struct ov2680_dev *sensor, s32 val)
 {
 	int ret;
 
-	ret = ov2680_mod_reg(sensor, OV2680_REG_FORMAT2, BIT(2), BIT(0));
+	if (sensor->is_streaming)
+		return -EBUSY;
+
+	ret = ov2680_mod_reg(sensor, OV2680_REG_FORMAT2,
+			     BIT(2), val ? BIT(2) : 0);
 	if (ret < 0)
 		return ret;
 
-	return ov2680_bayer_order(sensor);
+	ov2680_set_bayer_order(sensor, &sensor->fmt);
+	return 0;
 }
 
 static int ov2680_test_pattern_set(struct ov2680_dev *sensor, int value)
@@ -405,69 +394,15 @@
 	return 0;
 }
 
-static int ov2680_gain_set(struct ov2680_dev *sensor, bool auto_gain)
-{
-	struct ov2680_ctrls *ctrls = &sensor->ctrls;
-	u32 gain;
-	int ret;
-
-	ret = ov2680_mod_reg(sensor, OV2680_REG_R_MANUAL, BIT(1),
-			     auto_gain ? 0 : BIT(1));
-	if (ret < 0)
-		return ret;
-
-	if (auto_gain || !ctrls->gain->is_new)
-		return 0;
-
-	gain = ctrls->gain->val;
-
-	ret = ov2680_write_reg16(sensor, OV2680_REG_GAIN_PK, gain);
-
-	return 0;
-}
-
-static int ov2680_gain_get(struct ov2680_dev *sensor)
-{
-	u32 gain;
-	int ret;
-
-	ret = ov2680_read_reg16(sensor, OV2680_REG_GAIN_PK, &gain);
-	if (ret)
-		return ret;
-
-	return gain;
-}
-
-static int ov2680_exposure_set(struct ov2680_dev *sensor, bool auto_exp)
+static int ov2680_gain_set(struct ov2680_dev *sensor, u32 gain)
 {
-	struct ov2680_ctrls *ctrls = &sensor->ctrls;
-	u32 exp;
-	int ret;
-
-	ret = ov2680_mod_reg(sensor, OV2680_REG_R_MANUAL, BIT(0),
-			     auto_exp ? 0 : BIT(0));
-	if (ret < 0)
-		return ret;
-
-	if (auto_exp || !ctrls->exposure->is_new)
-		return 0;
-
-	exp = (u32)ctrls->exposure->val;
-	exp <<= 4;
-
-	return ov2680_write_reg24(sensor, OV2680_REG_EXPOSURE_PK_HIGH, exp);
+	return ov2680_write_reg16(sensor, OV2680_REG_GAIN_PK, gain);
 }
 
-static int ov2680_exposure_get(struct ov2680_dev *sensor)
+static int ov2680_exposure_set(struct ov2680_dev *sensor, u32 exp)
 {
-	int ret;
-	u32 exp;
-
-	ret = ov2680_read_reg24(sensor, OV2680_REG_EXPOSURE_PK_HIGH, &exp);
-	if (ret)
-		return ret;
-
-	return exp >> 4;
+	return ov2680_write_reg24(sensor, OV2680_REG_EXPOSURE_PK_HIGH,
+				  exp << 4);
 }
 
 static int ov2680_stream_enable(struct ov2680_dev *sensor)
@@ -482,33 +417,17 @@
 
 static int ov2680_mode_set(struct ov2680_dev *sensor)
 {
-	struct ov2680_ctrls *ctrls = &sensor->ctrls;
 	int ret;
 
-	ret = ov2680_gain_set(sensor, false);
-	if (ret < 0)
-		return ret;
-
-	ret = ov2680_exposure_set(sensor, false);
+	ret = ov2680_load_regs(sensor, sensor->current_mode);
 	if (ret < 0)
 		return ret;
 
-	ret = ov2680_load_regs(sensor, sensor->current_mode);
+	/* Restore value of all ctrls */
+	ret = __v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
 	if (ret < 0)
 		return ret;
 
-	if (ctrls->auto_gain->val) {
-		ret = ov2680_gain_set(sensor, true);
-		if (ret < 0)
-			return ret;
-	}
-
-	if (ctrls->auto_exp->val == V4L2_EXPOSURE_AUTO) {
-		ret = ov2680_exposure_set(sensor, true);
-		if (ret < 0)
-			return ret;
-	}
-
 	sensor->mode_pending_changes = false;
 
 	return 0;
@@ -556,7 +475,7 @@
 		ret = ov2680_write_reg(sensor, OV2680_REG_SOFT_RESET, 0x01);
 		if (ret != 0) {
 			dev_err(dev, "sensor soft reset failed\n");
-			return ret;
+			goto err_disable_regulators;
 		}
 		usleep_range(1000, 2000);
 	} else {
@@ -566,7 +485,7 @@
 
 	ret = clk_prepare_enable(sensor->xvclk);
 	if (ret < 0)
-		return ret;
+		goto err_disable_regulators;
 
 	sensor->is_enabled = true;
 
@@ -576,6 +495,10 @@
 	ov2680_stream_disable(sensor);
 
 	return 0;
+
+err_disable_regulators:
+	regulator_bulk_disable(OV2680_NUM_SUPPLIES, sensor->supplies);
+	return ret;
 }
 
 static int ov2680_s_power(struct v4l2_subdev *sd, int on)
@@ -590,15 +513,10 @@
 	else
 		ret = ov2680_power_off(sensor);
 
-	mutex_unlock(&sensor->lock);
-
-	if (on && ret == 0) {
-		ret = v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
-		if (ret < 0)
-			return ret;
-
+	if (on && ret == 0)
 		ret = ov2680_mode_restore(sensor);
-	}
+
+	mutex_unlock(&sensor->lock);
 
 	return ret;
 }
@@ -664,7 +582,6 @@
 {
 	struct ov2680_dev *sensor = to_ov2680_dev(sd);
 	struct v4l2_mbus_framefmt *fmt = NULL;
-	int ret = 0;
 
 	if (format->pad != 0)
 		return -EINVAL;
@@ -672,22 +589,17 @@
 	mutex_lock(&sensor->lock);
 
 	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
 		fmt = v4l2_subdev_get_try_format(&sensor->sd, sd_state,
 						 format->pad);
-#else
-		ret = -EINVAL;
-#endif
 	} else {
 		fmt = &sensor->fmt;
 	}
 
-	if (fmt)
-		format->format = *fmt;
+	format->format = *fmt;
 
 	mutex_unlock(&sensor->lock);
 
-	return ret;
+	return 0;
 }
 
 static int ov2680_set_fmt(struct v4l2_subdev *sd,
@@ -695,43 +607,35 @@
 			  struct v4l2_subdev_format *format)
 {
 	struct ov2680_dev *sensor = to_ov2680_dev(sd);
-	struct v4l2_mbus_framefmt *fmt = &format->format;
-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
 	struct v4l2_mbus_framefmt *try_fmt;
-#endif
 	const struct ov2680_mode_info *mode;
 	int ret = 0;
 
 	if (format->pad != 0)
 		return -EINVAL;
 
-	mutex_lock(&sensor->lock);
-
-	if (sensor->is_streaming) {
-		ret = -EBUSY;
-		goto unlock;
-	}
-
 	mode = v4l2_find_nearest_size(ov2680_mode_data,
-				      ARRAY_SIZE(ov2680_mode_data), width,
-				      height, fmt->width, fmt->height);
-	if (!mode) {
-		ret = -EINVAL;
-		goto unlock;
-	}
+				      ARRAY_SIZE(ov2680_mode_data),
+				      width, height,
+				      format->format.width,
+				      format->format.height);
+	if (!mode)
+		return -EINVAL;
+
+	ov2680_fill_format(sensor, &format->format, mode->width, mode->height);
 
 	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
 		try_fmt = v4l2_subdev_get_try_format(sd, sd_state, 0);
-		format->format = *try_fmt;
-#endif
-		goto unlock;
+		*try_fmt = format->format;
+		return 0;
 	}
 
-	fmt->width = mode->width;
-	fmt->height = mode->height;
-	fmt->code = sensor->fmt.code;
-	fmt->colorspace = sensor->fmt.colorspace;
+	mutex_lock(&sensor->lock);
+
+	if (sensor->is_streaming) {
+		ret = -EBUSY;
+		goto unlock;
+	}
 
 	sensor->current_mode = mode;
 	sensor->fmt = format->format;
@@ -746,16 +650,11 @@
 static int ov2680_init_cfg(struct v4l2_subdev *sd,
 			   struct v4l2_subdev_state *sd_state)
 {
-	struct v4l2_subdev_format fmt = {
-		.which = sd_state ? V4L2_SUBDEV_FORMAT_TRY
-		: V4L2_SUBDEV_FORMAT_ACTIVE,
-		.format = {
-			.width = 800,
-			.height = 600,
-		}
-	};
+	struct ov2680_dev *sensor = to_ov2680_dev(sd);
 
-	return ov2680_set_fmt(sd, sd_state, &fmt);
+	ov2680_fill_format(sensor, &sd_state->pads[0].try_fmt,
+			   OV2680_DEFAULT_WIDTH, OV2680_DEFAULT_HEIGHT);
+	return 0;
 }
 
 static int ov2680_enum_frame_size(struct v4l2_subdev *sd,
@@ -794,66 +693,23 @@
 	return 0;
 }
 
-static int ov2680_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
-{
-	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
-	struct ov2680_dev *sensor = to_ov2680_dev(sd);
-	struct ov2680_ctrls *ctrls = &sensor->ctrls;
-	int val;
-
-	if (!sensor->is_enabled)
-		return 0;
-
-	switch (ctrl->id) {
-	case V4L2_CID_GAIN:
-		val = ov2680_gain_get(sensor);
-		if (val < 0)
-			return val;
-		ctrls->gain->val = val;
-		break;
-	case V4L2_CID_EXPOSURE:
-		val = ov2680_exposure_get(sensor);
-		if (val < 0)
-			return val;
-		ctrls->exposure->val = val;
-		break;
-	}
-
-	return 0;
-}
-
 static int ov2680_s_ctrl(struct v4l2_ctrl *ctrl)
 {
 	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
 	struct ov2680_dev *sensor = to_ov2680_dev(sd);
-	struct ov2680_ctrls *ctrls = &sensor->ctrls;
 
 	if (!sensor->is_enabled)
 		return 0;
 
 	switch (ctrl->id) {
-	case V4L2_CID_AUTOGAIN:
-		return ov2680_gain_set(sensor, !!ctrl->val);
 	case V4L2_CID_GAIN:
-		return ov2680_gain_set(sensor, !!ctrls->auto_gain->val);
-	case V4L2_CID_EXPOSURE_AUTO:
-		return ov2680_exposure_set(sensor, !!ctrl->val);
+		return ov2680_gain_set(sensor, ctrl->val);
 	case V4L2_CID_EXPOSURE:
-		return ov2680_exposure_set(sensor, !!ctrls->auto_exp->val);
+		return ov2680_exposure_set(sensor, ctrl->val);
 	case V4L2_CID_VFLIP:
-		if (sensor->is_streaming)
-			return -EBUSY;
-		if (ctrl->val)
-			return ov2680_vflip_enable(sensor);
-		else
-			return ov2680_vflip_disable(sensor);
+		return ov2680_set_vflip(sensor, ctrl->val);
 	case V4L2_CID_HFLIP:
-		if (sensor->is_streaming)
-			return -EBUSY;
-		if (ctrl->val)
-			return ov2680_hflip_enable(sensor);
-		else
-			return ov2680_hflip_disable(sensor);
+		return ov2680_set_hflip(sensor, ctrl->val);
 	case V4L2_CID_TEST_PATTERN:
 		return ov2680_test_pattern_set(sensor, ctrl->val);
 	default:
@@ -864,7 +720,6 @@
 }
 
 static const struct v4l2_ctrl_ops ov2680_ctrl_ops = {
-	.g_volatile_ctrl = ov2680_g_volatile_ctrl,
 	.s_ctrl = ov2680_s_ctrl,
 };
 
@@ -898,11 +753,8 @@
 	const struct ov2680_mode_info *init_mode;
 
 	/* set initial mode */
-	sensor->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
-	sensor->fmt.width = 800;
-	sensor->fmt.height = 600;
-	sensor->fmt.field = V4L2_FIELD_NONE;
-	sensor->fmt.colorspace = V4L2_COLORSPACE_SRGB;
+	ov2680_fill_format(sensor, &sensor->fmt,
+			   OV2680_DEFAULT_WIDTH, OV2680_DEFAULT_HEIGHT);
 
 	sensor->frame_interval.denominator = OV2680_FRAME_RATE;
 	sensor->frame_interval.numerator = 1;
@@ -926,9 +778,7 @@
 	v4l2_i2c_subdev_init(&sensor->sd, sensor->i2c_client,
 			     &ov2680_subdev_ops);
 
-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
 	sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
-#endif
 	sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
 	sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
 
@@ -936,7 +786,7 @@
 	if (ret < 0)
 		return ret;
 
-	v4l2_ctrl_handler_init(hdl, 7);
+	v4l2_ctrl_handler_init(hdl, 5);
 
 	hdl->lock = &sensor->lock;
 
@@ -948,16 +798,9 @@
 					ARRAY_SIZE(test_pattern_menu) - 1,
 					0, 0, test_pattern_menu);
 
-	ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
-						 V4L2_CID_EXPOSURE_AUTO,
-						 V4L2_EXPOSURE_MANUAL, 0,
-						 V4L2_EXPOSURE_AUTO);
-
 	ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE,
 					    0, 32767, 1, 0);
 
-	ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTOGAIN,
-					     0, 1, 1, 1);
 	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN, 0, 2047, 1, 0);
 
 	if (hdl->error) {
@@ -965,11 +808,8 @@
 		goto cleanup_entity;
 	}
 
-	ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
-	ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
-
-	v4l2_ctrl_auto_cluster(2, &ctrls->auto_gain, 0, true);
-	v4l2_ctrl_auto_cluster(2, &ctrls->auto_exp, 1, true);
+	ctrls->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
+	ctrls->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
 
 	sensor->sd.ctrl_handler = hdl;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov2740.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov2740.c
@@ -603,8 +603,10 @@
 				     V4L2_CID_TEST_PATTERN,
 				     ARRAY_SIZE(ov2740_test_pattern_menu) - 1,
 				     0, 0, ov2740_test_pattern_menu);
-	if (ctrl_hdlr->error)
+	if (ctrl_hdlr->error) {
+		v4l2_ctrl_handler_free(ctrl_hdlr);
 		return ctrl_hdlr->error;
+	}
 
 	ov2740->sd.ctrl_handler = ctrl_hdlr;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov5640.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov5640.c
@@ -1406,6 +1406,7 @@
 			light_freq = 50;
 		} else {
 			/* 60Hz */
+			light_freq = 60;
 		}
 	}
 
@@ -1968,9 +1969,9 @@
 	 *		  "ov5640_set_stream_mipi()")
 	 * [4] = 0	: Power up MIPI HS Tx
 	 * [3] = 0	: Power up MIPI LS Rx
-	 * [2] = 0	: MIPI interface disabled
+	 * [2] = 1	: MIPI interface enabled
 	 */
-	ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x40);
+	ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x44);
 	if (ret)
 		return ret;
 
@@ -2293,7 +2294,6 @@
 	struct ov5640_dev *sensor = to_ov5640_dev(sd);
 	const struct ov5640_mode_info *new_mode;
 	struct v4l2_mbus_framefmt *mbus_fmt = &format->format;
-	struct v4l2_mbus_framefmt *fmt;
 	int ret;
 
 	if (format->pad != 0)
@@ -2311,12 +2311,10 @@
 	if (ret)
 		goto out;
 
-	if (format->which == V4L2_SUBDEV_FORMAT_TRY)
-		fmt = v4l2_subdev_get_try_format(sd, sd_state, 0);
-	else
-		fmt = &sensor->fmt;
-
-	*fmt = *mbus_fmt;
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		*v4l2_subdev_get_try_format(sd, sd_state, 0) = *mbus_fmt;
+		goto out;
+	}
 
 	if (new_mode != sensor->current_mode) {
 		sensor->current_mode = new_mode;
@@ -2325,6 +2323,9 @@
 	if (mbus_fmt->code != sensor->fmt.code)
 		sensor->pending_fmt_change = true;
 
+	/* update format even if code is unchanged, resolution might change */
+	sensor->fmt = *mbus_fmt;
+
 	__v4l2_ctrl_s_ctrl_int64(sensor->ctrls.pixel_rate,
 				 ov5640_calc_pixel_rate(sensor));
 out:
@@ -2663,6 +2664,13 @@
 
 	/* v4l2_ctrl_lock() locks our own mutex */
 
+	/*
+	 * If the sensor is not powered up by the host driver, do
+	 * not try to access it to update the volatile controls.
+	 */
+	if (sensor->power_count == 0)
+		return 0;
+
 	switch (ctrl->id) {
 	case V4L2_CID_AUTOGAIN:
 		val = ov5640_get_gain(sensor);
@@ -2776,7 +2784,7 @@
 	/* Auto/manual gain */
 	ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTOGAIN,
 					     0, 1, 1, 1);
-	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
+	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_ANALOGUE_GAIN,
 					0, 1023, 1, 0);
 
 	ctrls->saturation = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov5648.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov5648.c
@@ -639,7 +639,7 @@
 	struct v4l2_ctrl *pixel_rate;
 
 	struct v4l2_ctrl_handler handler;
-} __packed;
+};
 
 struct ov5648_sensor {
 	struct device *dev;
@@ -1778,8 +1778,14 @@
 
 static int ov5648_state_init(struct ov5648_sensor *sensor)
 {
-	return ov5648_state_configure(sensor, &ov5648_modes[0],
-				      ov5648_mbus_codes[0]);
+	int ret;
+
+	mutex_lock(&sensor->mutex);
+	ret = ov5648_state_configure(sensor, &ov5648_modes[0],
+				     ov5648_mbus_codes[0]);
+	mutex_unlock(&sensor->mutex);
+
+	return ret;
 }
 
 /* Sensor Base */
@@ -2492,9 +2498,9 @@
 
 	/* DOVDD: digital I/O */
 	sensor->dovdd = devm_regulator_get(dev, "dovdd");
-	if (IS_ERR(sensor->dvdd)) {
+	if (IS_ERR(sensor->dovdd)) {
 		dev_err(dev, "cannot get DOVDD (digital I/O) regulator\n");
-		ret = PTR_ERR(sensor->dvdd);
+		ret = PTR_ERR(sensor->dovdd);
 		goto error_endpoint;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov5675.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov5675.c
@@ -791,8 +791,10 @@
 	v4l2_ctrl_new_std(ctrl_hdlr, &ov5675_ctrl_ops,
 			  V4L2_CID_VFLIP, 0, 1, 1, 0);
 
-	if (ctrl_hdlr->error)
+	if (ctrl_hdlr->error) {
+		v4l2_ctrl_handler_free(ctrl_hdlr);
 		return ctrl_hdlr->error;
+	}
 
 	ov5675->sd.ctrl_handler = ctrl_hdlr;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov6650.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov6650.c
@@ -472,9 +472,16 @@
 {
 	struct i2c_client *client = v4l2_get_subdevdata(sd);
 	struct ov6650 *priv = to_ov6650(client);
+	struct v4l2_rect *rect;
 
-	if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE)
-		return -EINVAL;
+	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+		/* pre-select try crop rectangle */
+		rect = &sd_state->pads->try_crop;
+
+	} else {
+		/* pre-select active crop rectangle */
+		rect = &priv->rect;
+	}
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
@@ -483,14 +490,33 @@
 		sel->r.width = W_CIF;
 		sel->r.height = H_CIF;
 		return 0;
+
 	case V4L2_SEL_TGT_CROP:
-		sel->r = priv->rect;
+		/* use selected crop rectangle */
+		sel->r = *rect;
 		return 0;
+
 	default:
 		return -EINVAL;
 	}
 }
 
+static bool is_unscaled_ok(int width, int height, struct v4l2_rect *rect)
+{
+	return width > rect->width >> 1 || height > rect->height >> 1;
+}
+
+static void ov6650_bind_align_crop_rectangle(struct v4l2_rect *rect)
+{
+	v4l_bound_align_image(&rect->width, 2, W_CIF, 1,
+			      &rect->height, 2, H_CIF, 1, 0);
+	v4l_bound_align_image(&rect->left, DEF_HSTRT << 1,
+			      (DEF_HSTRT << 1) + W_CIF - (__s32)rect->width, 1,
+			      &rect->top, DEF_VSTRT << 1,
+			      (DEF_VSTRT << 1) + H_CIF - (__s32)rect->height,
+			      1, 0);
+}
+
 static int ov6650_set_selection(struct v4l2_subdev *sd,
 		struct v4l2_subdev_state *sd_state,
 		struct v4l2_subdev_selection *sel)
@@ -499,18 +525,30 @@
 	struct ov6650 *priv = to_ov6650(client);
 	int ret;
 
-	if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE ||
-	    sel->target != V4L2_SEL_TGT_CROP)
+	if (sel->target != V4L2_SEL_TGT_CROP)
 		return -EINVAL;
 
-	v4l_bound_align_image(&sel->r.width, 2, W_CIF, 1,
-			      &sel->r.height, 2, H_CIF, 1, 0);
-	v4l_bound_align_image(&sel->r.left, DEF_HSTRT << 1,
-			      (DEF_HSTRT << 1) + W_CIF - (__s32)sel->r.width, 1,
-			      &sel->r.top, DEF_VSTRT << 1,
-			      (DEF_VSTRT << 1) + H_CIF - (__s32)sel->r.height,
-			      1, 0);
+	ov6650_bind_align_crop_rectangle(&sel->r);
 
+	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
+		struct v4l2_rect *crop = &sd_state->pads->try_crop;
+		struct v4l2_mbus_framefmt *mf = &sd_state->pads->try_fmt;
+		/* detect current pad config scaling factor */
+		bool half_scale = !is_unscaled_ok(mf->width, mf->height, crop);
+
+		/* store new crop rectangle */
+		*crop = sel->r;
+
+		/* adjust frame size */
+		mf->width = crop->width >> half_scale;
+		mf->height = crop->height >> half_scale;
+
+		return 0;
+	}
+
+	/* V4L2_SUBDEV_FORMAT_ACTIVE */
+
+	/* apply new crop rectangle */
 	ret = ov6650_reg_write(client, REG_HSTRT, sel->r.left >> 1);
 	if (!ret) {
 		priv->rect.width += priv->rect.left - sel->r.left;
@@ -562,30 +600,13 @@
 	return 0;
 }
 
-static bool is_unscaled_ok(int width, int height, struct v4l2_rect *rect)
-{
-	return width > rect->width >> 1 || height > rect->height >> 1;
-}
-
 #define to_clkrc(div)	((div) - 1)
 
 /* set the format we will capture in */
-static int ov6650_s_fmt(struct v4l2_subdev *sd, struct v4l2_mbus_framefmt *mf)
+static int ov6650_s_fmt(struct v4l2_subdev *sd, u32 code, bool half_scale)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(sd);
 	struct ov6650 *priv = to_ov6650(client);
-	bool half_scale = !is_unscaled_ok(mf->width, mf->height, &priv->rect);
-	struct v4l2_subdev_selection sel = {
-		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
-		.target = V4L2_SEL_TGT_CROP,
-		.r.left = priv->rect.left + (priv->rect.width >> 1) -
-			(mf->width >> (1 - half_scale)),
-		.r.top = priv->rect.top + (priv->rect.height >> 1) -
-			(mf->height >> (1 - half_scale)),
-		.r.width = mf->width << half_scale,
-		.r.height = mf->height << half_scale,
-	};
-	u32 code = mf->code;
 	u8 coma_set = 0, coma_mask = 0, coml_set, coml_mask;
 	int ret;
 
@@ -653,9 +674,7 @@
 		coma_mask |= COMA_QCIF;
 	}
 
-	ret = ov6650_set_selection(sd, NULL, &sel);
-	if (!ret)
-		ret = ov6650_reg_rmw(client, REG_COMA, coma_set, coma_mask);
+	ret = ov6650_reg_rmw(client, REG_COMA, coma_set, coma_mask);
 	if (!ret) {
 		priv->half_scale = half_scale;
 
@@ -674,14 +693,12 @@
 	struct v4l2_mbus_framefmt *mf = &format->format;
 	struct i2c_client *client = v4l2_get_subdevdata(sd);
 	struct ov6650 *priv = to_ov6650(client);
+	struct v4l2_rect *crop;
+	bool half_scale;
 
 	if (format->pad)
 		return -EINVAL;
 
-	if (is_unscaled_ok(mf->width, mf->height, &priv->rect))
-		v4l_bound_align_image(&mf->width, 2, W_CIF, 1,
-				&mf->height, 2, H_CIF, 1, 0);
-
 	switch (mf->code) {
 	case MEDIA_BUS_FMT_Y10_1X10:
 		mf->code = MEDIA_BUS_FMT_Y8_1X8;
@@ -699,10 +716,17 @@
 		break;
 	}
 
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY)
+		crop = &sd_state->pads->try_crop;
+	else
+		crop = &priv->rect;
+
+	half_scale = !is_unscaled_ok(mf->width, mf->height, crop);
+
 	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
-		/* store media bus format code and frame size in pad config */
-		sd_state->pads->try_fmt.width = mf->width;
-		sd_state->pads->try_fmt.height = mf->height;
+		/* store new mbus frame format code and size in pad config */
+		sd_state->pads->try_fmt.width = crop->width >> half_scale;
+		sd_state->pads->try_fmt.height = crop->height >> half_scale;
 		sd_state->pads->try_fmt.code = mf->code;
 
 		/* return default mbus frame format updated with pad config */
@@ -712,9 +736,11 @@
 		mf->code = sd_state->pads->try_fmt.code;
 
 	} else {
-		/* apply new media bus format code and frame size */
-		int ret = ov6650_s_fmt(sd, mf);
+		int ret = 0;
 
+		/* apply new media bus frame format and scaling if changed */
+		if (mf->code != priv->code || half_scale != priv->half_scale)
+			ret = ov6650_s_fmt(sd, mf->code, half_scale);
 		if (ret)
 			return ret;
 
@@ -890,9 +916,8 @@
 	if (!ret)
 		ret = ov6650_prog_dflt(client, xclk->clkrc);
 	if (!ret) {
-		struct v4l2_mbus_framefmt mf = ov6650_def_fmt;
-
-		ret = ov6650_s_fmt(sd, &mf);
+		/* driver default frame format, no scaling */
+		ret = ov6650_s_fmt(sd, ov6650_def_fmt.code, false);
 	}
 	if (!ret)
 		ret = v4l2_ctrl_handler_setup(&priv->hdl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov7670.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov7670.c
@@ -1841,7 +1841,7 @@
 
 	if (bus_cfg.bus_type != V4L2_MBUS_PARALLEL) {
 		dev_err(dev, "Unsupported media bus type\n");
-		return ret;
+		return -EINVAL;
 	}
 	info->mbus_config = bus_cfg.bus.parallel.flags;
 
@@ -2017,7 +2017,6 @@
 	v4l2_async_unregister_subdev(sd);
 	v4l2_ctrl_handler_free(&info->hdl);
 	media_entity_cleanup(&info->sd.entity);
-	ov7670_power_off(sd);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov772x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov772x.c
@@ -1462,7 +1462,7 @@
 	priv->subdev.ctrl_handler = &priv->hdl;
 	if (priv->hdl.error) {
 		ret = priv->hdl.error;
-		goto error_mutex_destroy;
+		goto error_ctrl_free;
 	}
 
 	priv->clk = clk_get(&client->dev, NULL);
@@ -1515,7 +1515,6 @@
 	clk_put(priv->clk);
 error_ctrl_free:
 	v4l2_ctrl_handler_free(&priv->hdl);
-error_mutex_destroy:
 	mutex_destroy(&priv->lock);
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov8865.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov8865.c
@@ -2330,27 +2330,27 @@
 		if (ret) {
 			dev_err(sensor->dev,
 				"failed to enable DOVDD regulator\n");
-			goto disable;
+			return ret;
 		}
 
 		ret = regulator_enable(sensor->avdd);
 		if (ret) {
 			dev_err(sensor->dev,
 				"failed to enable AVDD regulator\n");
-			goto disable;
+			goto disable_dovdd;
 		}
 
 		ret = regulator_enable(sensor->dvdd);
 		if (ret) {
 			dev_err(sensor->dev,
 				"failed to enable DVDD regulator\n");
-			goto disable;
+			goto disable_avdd;
 		}
 
 		ret = clk_prepare_enable(sensor->extclk);
 		if (ret) {
 			dev_err(sensor->dev, "failed to enable EXTCLK clock\n");
-			goto disable;
+			goto disable_dvdd;
 		}
 
 		gpiod_set_value_cansleep(sensor->reset, 0);
@@ -2359,14 +2359,16 @@
 		/* Time to enter streaming mode according to power timings. */
 		usleep_range(10000, 12000);
 	} else {
-disable:
 		gpiod_set_value_cansleep(sensor->powerdown, 1);
 		gpiod_set_value_cansleep(sensor->reset, 1);
 
 		clk_disable_unprepare(sensor->extclk);
 
+disable_dvdd:
 		regulator_disable(sensor->dvdd);
+disable_avdd:
 		regulator_disable(sensor->avdd);
+disable_dovdd:
 		regulator_disable(sensor->dovdd);
 	}
 
@@ -2891,14 +2893,16 @@
 	if (ret)
 		goto error_mutex;
 
+	mutex_lock(&sensor->mutex);
 	ret = ov8865_state_init(sensor);
+	mutex_unlock(&sensor->mutex);
 	if (ret)
 		goto error_ctrls;
 
 	/* Runtime PM */
 
-	pm_runtime_enable(sensor->dev);
 	pm_runtime_set_suspended(sensor->dev);
+	pm_runtime_enable(sensor->dev);
 
 	/* V4L2 subdev register */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov9282.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov9282.c
@@ -31,7 +31,7 @@
 /* Exposure control */
 #define OV9282_REG_EXPOSURE	0x3500
 #define OV9282_EXPOSURE_MIN	1
-#define OV9282_EXPOSURE_OFFSET	12
+#define OV9282_EXPOSURE_OFFSET	25
 #define OV9282_EXPOSURE_STEP	1
 #define OV9282_EXPOSURE_DEFAULT	0x0282
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/ov9734.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/ov9734.c
@@ -939,6 +939,7 @@
 	media_entity_cleanup(&sd->entity);
 	v4l2_ctrl_handler_free(sd->ctrl_handler);
 	pm_runtime_disable(&client->dev);
+	pm_runtime_set_suspended(&client->dev);
 	mutex_destroy(&ov9734->mutex);
 
 	return 0;
@@ -986,13 +987,6 @@
 		goto probe_error_v4l2_ctrl_handler_free;
 	}
 
-	ret = v4l2_async_register_subdev_sensor(&ov9734->sd);
-	if (ret < 0) {
-		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
-			ret);
-		goto probe_error_media_entity_cleanup;
-	}
-
 	/*
 	 * Device is already turned on by i2c-core with ACPI domain PM.
 	 * Enable runtime PM and turn off the device.
@@ -1001,9 +995,18 @@
 	pm_runtime_enable(&client->dev);
 	pm_runtime_idle(&client->dev);
 
+	ret = v4l2_async_register_subdev_sensor(&ov9734->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto probe_error_media_entity_cleanup_pm;
+	}
+
 	return 0;
 
-probe_error_media_entity_cleanup:
+probe_error_media_entity_cleanup_pm:
+	pm_runtime_disable(&client->dev);
+	pm_runtime_set_suspended(&client->dev);
 	media_entity_cleanup(&ov9734->sd.entity);
 
 probe_error_v4l2_ctrl_handler_free:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/power_ctrl_logic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/power_ctrl_logic.c
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020-2021 Intel Corporation.
+
+#include <linux/acpi.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/gpio/consumer.h>
+
+#define PCL_DRV_NAME "power_ctrl_logic"
+
+struct power_ctrl_logic {
+	/* gpio resource*/
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *powerdn_gpio;
+	struct gpio_desc *clocken_gpio;
+	struct gpio_desc *indled_gpio;
+	/* status */
+	struct mutex status_lock;
+	bool power_on;
+	bool gpio_ready;
+};
+
+struct power_ctrl_gpio {
+	const char *name;
+	struct gpio_desc **pin;
+};
+
+/* mcu gpio resources*/
+static const struct acpi_gpio_params camreset_gpio  = { 0, 0, false };
+static const struct acpi_gpio_params campwdn_gpio   = { 1, 0, false };
+static const struct acpi_gpio_params midmclken_gpio = { 2, 0, false };
+static const struct acpi_gpio_params led_gpio       = { 3, 0, false };
+static const struct acpi_gpio_mapping dsc1_acpi_gpios[] = {
+	{ "camreset-gpios", &camreset_gpio, 1 },
+	{ "campwdn-gpios", &campwdn_gpio, 1 },
+	{ "midmclken-gpios", &midmclken_gpio, 1 },
+	{ "indled-gpios", &led_gpio, 1 },
+	{ }
+};
+
+static struct power_ctrl_logic pcl = {
+	.reset_gpio = NULL,
+	.powerdn_gpio = NULL,
+	.clocken_gpio = NULL,
+	.indled_gpio = NULL,
+	.power_on = false,
+	.gpio_ready = false,
+};
+
+static struct power_ctrl_gpio pcl_gpios[] = {
+	{ "camreset", &pcl.reset_gpio },
+	{ "campwdn", &pcl.powerdn_gpio },
+	{ "midmclken", &pcl.clocken_gpio},
+	{ "indled", &pcl.indled_gpio},
+};
+
+static int power_ctrl_logic_add(struct acpi_device *adev)
+{
+	int i, ret;
+
+	dev_dbg(&adev->dev, "@%s, enter\n", __func__);
+	set_primary_fwnode(&adev->dev, &adev->fwnode);
+
+	ret = acpi_dev_add_driver_gpios(adev, dsc1_acpi_gpios);
+	if (ret) {
+		dev_err(&adev->dev, "@%s: --111---fail to add gpio. ret %d\n", __func__, ret);
+		return -EBUSY;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(pcl_gpios); i++) {
+		*pcl_gpios[i].pin = gpiod_get(&adev->dev, pcl_gpios[i].name, GPIOD_OUT_LOW);
+		if (IS_ERR(*pcl_gpios[i].pin)) {
+			dev_dbg(&adev->dev, "failed to get gpio %s\n", pcl_gpios[i].name);
+			return -EPROBE_DEFER;
+		}
+	}
+
+	mutex_lock(&pcl.status_lock);
+	pcl.gpio_ready = true;
+	mutex_unlock(&pcl.status_lock);
+
+	dev_dbg(&adev->dev, "@%s, exit\n", __func__);
+	return ret;
+}
+
+static int power_ctrl_logic_remove(struct acpi_device *adev)
+{
+	dev_dbg(&adev->dev, "@%s, enter\n", __func__);
+	mutex_lock(&pcl.status_lock);
+	pcl.gpio_ready = false;
+	gpiod_set_value_cansleep(pcl.reset_gpio, 0);
+	gpiod_put(pcl.reset_gpio);
+	gpiod_set_value_cansleep(pcl.powerdn_gpio, 0);
+	gpiod_put(pcl.powerdn_gpio);
+	gpiod_set_value_cansleep(pcl.clocken_gpio, 0);
+	gpiod_put(pcl.clocken_gpio);
+	gpiod_set_value_cansleep(pcl.indled_gpio, 0);
+	gpiod_put(pcl.indled_gpio);
+	mutex_unlock(&pcl.status_lock);
+	dev_dbg(&adev->dev, "@%s, exit\n", __func__);
+	return 0;
+}
+
+static struct acpi_device_id acpi_ids[] = {
+	{ "INT3472", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, acpi_ids);
+
+static struct acpi_driver _driver = {
+	.name = PCL_DRV_NAME,
+	.class = PCL_DRV_NAME,
+	.ids = acpi_ids,
+	.ops = {
+		.add = power_ctrl_logic_add,
+		.remove = power_ctrl_logic_remove,
+	},
+};
+module_acpi_driver(_driver);
+
+int power_ctrl_logic_set_power(int on)
+{
+	mutex_lock(&pcl.status_lock);
+	if (!pcl.gpio_ready) {
+		pr_debug("@%s,failed to set power, gpio_ready=%d, on=%d\n",
+			 __func__, pcl.gpio_ready, on);
+		mutex_unlock(&pcl.status_lock);
+		return -EPROBE_DEFER;
+	}
+	if (pcl.power_on != on) {
+		gpiod_set_value_cansleep(pcl.reset_gpio, on);
+		gpiod_set_value_cansleep(pcl.powerdn_gpio, on);
+		gpiod_set_value_cansleep(pcl.clocken_gpio, on);
+		gpiod_set_value_cansleep(pcl.indled_gpio, on);
+		pcl.power_on = on;
+	}
+	mutex_unlock(&pcl.status_lock);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(power_ctrl_logic_set_power);
+
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_AUTHOR("Qiu, Tianshu <tian.shu.qiu@intel.com>");
+MODULE_AUTHOR("Xu, Chongyang <chongyang.xu@intel.com>");
+MODULE_DESCRIPTION("Power Control Logic Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/power_ctrl_logic.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/power_ctrl_logic.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2020-2021 Intel Corporation. */
+
+#ifndef _POWER_CTRL_LOGIC_H_
+#define _POWER_CTRL_LOGIC_H_
+
+/* exported function for extern module */
+int power_ctrl_logic_set_power(int on);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/rdacm20.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/rdacm20.c
@@ -611,7 +611,7 @@
 		goto error_free_ctrls;
 
 	dev->pad.flags = MEDIA_PAD_FL_SOURCE;
-	dev->sd.entity.flags |= MEDIA_ENT_F_CAM_SENSOR;
+	dev->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
 	ret = media_entity_pads_init(&dev->sd.entity, 1, &dev->pad);
 	if (ret < 0)
 		goto error_free_ctrls;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/rdacm21.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/rdacm21.c
@@ -351,7 +351,7 @@
 static int ov10640_check_id(struct rdacm21_device *dev)
 {
 	unsigned int i;
-	u8 val;
+	u8 val = 0;
 
 	/* Read OV10640 ID to test communications. */
 	for (i = 0; i < OV10640_PID_TIMEOUT; ++i) {
@@ -583,7 +583,7 @@
 		goto error_free_ctrls;
 
 	dev->pad.flags = MEDIA_PAD_FL_SOURCE;
-	dev->sd.entity.flags |= MEDIA_ENT_F_CAM_SENSOR;
+	dev->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
 	ret = media_entity_pads_init(&dev->sd.entity, 1, &dev->pad);
 	if (ret < 0)
 		goto error_free_ctrls;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/st-mipid02.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/st-mipid02.c
@@ -710,8 +710,13 @@
 {
 	struct mipid02_dev *bridge = to_mipid02_dev(sd);
 
-	/* source pad mirror active sink pad */
-	format->format = bridge->fmt;
+	/* source pad mirror sink pad */
+	if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+		format->format = bridge->fmt;
+	else
+		format->format = *v4l2_subdev_get_try_format(sd, sd_state,
+							     MIPID02_SINK_0);
+
 	/* but code may need to be converted */
 	format->format.code = serial_to_parallel_code(format->format.code);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/tc358743.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/tc358743.c
@@ -2108,9 +2108,6 @@
 	state->mbus_fmt_code = MEDIA_BUS_FMT_RGB888_1X24;
 
 	sd->dev = &client->dev;
-	err = v4l2_async_register_subdev(sd);
-	if (err < 0)
-		goto err_hdl;
 
 	mutex_init(&state->confctl_mutex);
 
@@ -2168,6 +2165,10 @@
 	if (err)
 		goto err_work_queues;
 
+	err = v4l2_async_register_subdev(sd);
+	if (err < 0)
+		goto err_work_queues;
+
 	v4l2_info(sd, "%s found @ 0x%x (%s)\n", client->name,
 		  client->addr << 1, client->adapter->name);
 
@@ -2175,8 +2176,10 @@
 
 err_work_queues:
 	cec_unregister_adapter(state->cec_adap);
-	if (!state->i2c_client->irq)
+	if (!state->i2c_client->irq) {
+		del_timer(&state->timer);
 		flush_work(&state->work_i2c_poll);
+	}
 	cancel_delayed_work(&state->delayed_work_enable_hotplug);
 	mutex_destroy(&state->confctl_mutex);
 err_hdl:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/tda1997x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/tda1997x.c
@@ -1248,13 +1248,13 @@
 {
 	struct v4l2_subdev *sd = &state->sd;
 	union hdmi_infoframe frame;
-	u8 buffer[40];
+	u8 buffer[40] = { 0 };
 	u8 reg;
 	int len, err;
 
 	/* read data */
 	len = io_readn(sd, addr, sizeof(buffer), buffer);
-	err = hdmi_infoframe_unpack(&frame, buffer, sizeof(buffer));
+	err = hdmi_infoframe_unpack(&frame, buffer, len);
 	if (err) {
 		v4l_err(state->client,
 			"failed parsing %d byte infoframe: 0x%04x/0x%02x\n",
@@ -1928,13 +1928,13 @@
 {
 	struct tda1997x_state *state = to_state(sd);
 	union hdmi_infoframe frame;
-	u8 buffer[40];
+	u8 buffer[40] = { 0 };
 	int len, err;
 
 	/* read data */
 	len = io_readn(sd, addr, sizeof(buffer), buffer);
 	v4l2_dbg(1, debug, sd, "infoframe: addr=%d len=%d\n", addr, len);
-	err = hdmi_infoframe_unpack(&frame, buffer, sizeof(buffer));
+	err = hdmi_infoframe_unpack(&frame, buffer, len);
 	if (err) {
 		v4l_err(state->client,
 			"failed parsing %d byte infoframe: 0x%04x/0x%02x\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/i2c/tvp5150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/i2c/tvp5150.c
@@ -2066,6 +2066,10 @@
 		tvpc->ent.name = devm_kasprintf(dev, GFP_KERNEL, "%s %s",
 						v4l2c->name, v4l2c->label ?
 						v4l2c->label : "");
+		if (!tvpc->ent.name) {
+			ret = -ENOMEM;
+			goto err_free;
+		}
 	}
 
 	ep_np = of_graph_get_endpoint_by_regs(np, TVP5150_PAD_VID_OUT, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/mc/mc-devnode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/mc/mc-devnode.c
@@ -246,15 +246,14 @@
 	kobject_set_name(&devnode->cdev.kobj, "media%d", devnode->minor);
 
 	/* Part 3: Add the media and char device */
+	set_bit(MEDIA_FLAG_REGISTERED, &devnode->flags);
 	ret = cdev_device_add(&devnode->cdev, &devnode->dev);
 	if (ret < 0) {
+		clear_bit(MEDIA_FLAG_REGISTERED, &devnode->flags);
 		pr_err("%s: cdev_device_add failed\n", __func__);
 		goto cdev_add_error;
 	}
 
-	/* Part 4: Activate this minor. The char device can now be used. */
-	set_bit(MEDIA_FLAG_REGISTERED, &devnode->flags);
-
 	return 0;
 
 cdev_add_error:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/mc/mc-entity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/mc/mc-entity.c
@@ -264,7 +264,36 @@
 #define stack_top(en)	((en)->stack[(en)->top].entity)
 
 /**
- * media_graph_walk_init - Allocate resources for graph walk
+ * media_entity_has_route - Check if two entity pads are connected internally
+ * @entity: The entity
+ * @pad0: The first pad index
+ * @pad1: The second pad index
+ *
+ * This function can be used to check whether two pads of an entity are
+ * connected internally in the entity.
+ *
+ * The caller must hold entity->source->parent->mutex.
+ *
+ * Return: true if the pads are connected internally and false otherwise.
+ */
+bool media_entity_has_route(struct media_entity *entity, unsigned int pad0,
+			    unsigned int pad1)
+{
+	if (pad0 >= entity->num_pads || pad1 >= entity->num_pads)
+		return false;
+
+	if (pad0 == pad1)
+		return true;
+
+	if (!entity->ops || !entity->ops->has_route)
+		return true;
+
+	return entity->ops->has_route(entity, pad0, pad1);
+}
+EXPORT_SYMBOL_GPL(media_entity_has_route);
+
+/**
+ * media_entity_graph_walk_init - Allocate resources for graph walk
  * @graph: Media graph structure that will be used to walk the graph
  * @mdev: Media device
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/Kconfig
@@ -55,7 +55,7 @@
 source "drivers/media/pci/netup_unidvb/Kconfig"
 endif
 
-source "drivers/media/pci/intel/ipu3/Kconfig"
+source "drivers/media/pci/intel/Kconfig"
 
 config VIDEO_PCI_SKELETON
 	tristate "Skeleton PCI V4L2 driver"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/b2c2/flexcop-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/b2c2/flexcop-pci.c
@@ -185,6 +185,8 @@
 		dma_addr_t cur_addr =
 			fc->read_ibi_reg(fc,dma1_008).dma_0x8.dma_cur_addr << 2;
 		u32 cur_pos = cur_addr - fc_pci->dma[0].dma_addr0;
+		if (cur_pos > fc_pci->dma[0].size * 2)
+			goto error;
 
 		deb_irq("%u irq: %08x cur_addr: %llx: cur_pos: %08x, last_cur_pos: %08x ",
 				jiffies_to_usecs(jiffies - fc_pci->last_irq),
@@ -225,6 +227,7 @@
 		ret = IRQ_NONE;
 	}
 
+error:
 	spin_unlock_irqrestore(&fc_pci->irq_lock, flags);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/bt8xx/bttv-driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/bt8xx/bttv-driver.c
@@ -3890,7 +3890,7 @@
 
 	/* video */
 	vdev_init(btv, &btv->video_dev, &bttv_video_template, "video");
-	btv->video_dev.device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_TUNER |
+	btv->video_dev.device_caps = V4L2_CAP_VIDEO_CAPTURE |
 				     V4L2_CAP_READWRITE | V4L2_CAP_STREAMING;
 	if (btv->tuner_type != TUNER_ABSENT)
 		btv->video_dev.device_caps |= V4L2_CAP_TUNER;
@@ -3911,7 +3911,7 @@
 	/* vbi */
 	vdev_init(btv, &btv->vbi_dev, &bttv_video_template, "vbi");
 	btv->vbi_dev.device_caps = V4L2_CAP_VBI_CAPTURE | V4L2_CAP_READWRITE |
-				   V4L2_CAP_STREAMING | V4L2_CAP_TUNER;
+				   V4L2_CAP_STREAMING;
 	if (btv->tuner_type != TUNER_ABSENT)
 		btv->vbi_dev.device_caps |= V4L2_CAP_TUNER;
 
@@ -4250,6 +4250,7 @@
 
 	/* free resources */
 	free_irq(btv->c.pci->irq,btv);
+	del_timer_sync(&btv->timeout);
 	iounmap(btv->bt848_mmio);
 	release_mem_region(pci_resource_start(btv->c.pci,0),
 			   pci_resource_len(btv->c.pci,0));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/bt8xx/dst.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/bt8xx/dst.c
@@ -1722,7 +1722,7 @@
 	return state;				/*	Manu (DST is a card not a frontend)	*/
 }
 
-EXPORT_SYMBOL(dst_attach);
+EXPORT_SYMBOL_GPL(dst_attach);
 
 static const struct dvb_frontend_ops dst_dvbt_ops = {
 	.delsys = { SYS_DVBT },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/bt8xx/dst_ca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/bt8xx/dst_ca.c
@@ -668,7 +668,7 @@
 	return NULL;
 }
 
-EXPORT_SYMBOL(dst_ca_attach);
+EXPORT_SYMBOL_GPL(dst_ca_attach);
 
 MODULE_DESCRIPTION("DST DVB-S/T/C Combo CA driver");
 MODULE_AUTHOR("Manu Abraham");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cobalt/cobalt-driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cobalt/cobalt-driver.c
@@ -8,6 +8,7 @@
  *  All rights reserved.
  */
 
+#include <linux/bitfield.h>
 #include <linux/delay.h>
 #include <media/i2c/adv7604.h>
 #include <media/i2c/adv7842.h>
@@ -210,17 +211,17 @@
 	pcie_capability_read_word(pci_dev, PCI_EXP_LNKSTA, &stat);
 	cobalt_info("PCIe link capability 0x%08x: %s per lane and %u lanes\n",
 			capa, get_link_speed(capa),
-			(capa & PCI_EXP_LNKCAP_MLW) >> 4);
+			FIELD_GET(PCI_EXP_LNKCAP_MLW, capa));
 	cobalt_info("PCIe link control 0x%04x\n", ctrl);
 	cobalt_info("PCIe link status 0x%04x: %s per lane and %u lanes\n",
 		    stat, get_link_speed(stat),
-		    (stat & PCI_EXP_LNKSTA_NLW) >> 4);
+		    FIELD_GET(PCI_EXP_LNKSTA_NLW, stat));
 
 	/* Bus */
 	pcie_capability_read_dword(pci_bus_dev, PCI_EXP_LNKCAP, &capa);
 	cobalt_info("PCIe bus link capability 0x%08x: %s per lane and %u lanes\n",
 			capa, get_link_speed(capa),
-			(capa & PCI_EXP_LNKCAP_MLW) >> 4);
+			FIELD_GET(PCI_EXP_LNKCAP_MLW, capa));
 
 	/* Slot */
 	pcie_capability_read_dword(pci_dev, PCI_EXP_SLTCAP, &capa);
@@ -239,7 +240,7 @@
 	if (!pci_is_pcie(pci_dev))
 		return 0;
 	pcie_capability_read_word(pci_dev, PCI_EXP_LNKSTA, &link);
-	return (link & PCI_EXP_LNKSTA_NLW) >> 4;
+	return FIELD_GET(PCI_EXP_LNKSTA_NLW, link);
 }
 
 static unsigned pcie_bus_link_get_lanes(struct cobalt *cobalt)
@@ -250,7 +251,7 @@
 	if (!pci_is_pcie(pci_dev))
 		return 0;
 	pcie_capability_read_dword(pci_dev, PCI_EXP_LNKCAP, &link);
-	return (link & PCI_EXP_LNKCAP_MLW) >> 4;
+	return FIELD_GET(PCI_EXP_LNKCAP_MLW, link);
 }
 
 static void msi_config_show(struct cobalt *cobalt, struct pci_dev *pci_dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx23885/cx23885-alsa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx23885/cx23885-alsa.c
@@ -550,7 +550,7 @@
 			   SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1,
 			THIS_MODULE, sizeof(struct cx23885_audio_dev), &card);
 	if (err < 0)
-		goto error;
+		goto error_msg;
 
 	chip = (struct cx23885_audio_dev *) card->private_data;
 	chip->dev = dev;
@@ -576,6 +576,7 @@
 
 error:
 	snd_card_free(card);
+error_msg:
 	pr_err("%s(): Failed to register analog audio adapter\n",
 	       __func__);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx23885/cx23885-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx23885/cx23885-core.c
@@ -1325,7 +1325,9 @@
 {
 	struct cx23885_riscmem *risc = &buf->risc;
 
-	dma_free_coherent(&dev->pci->dev, risc->size, risc->cpu, risc->dma);
+	if (risc->cpu)
+		dma_free_coherent(&dev->pci->dev, risc->size, risc->cpu, risc->dma);
+	memset(risc, 0, sizeof(*risc));
 }
 
 static void cx23885_tsport_reg_dump(struct cx23885_tsport *port)
@@ -2165,7 +2167,7 @@
 	err = dma_set_mask(&pci_dev->dev, 0xffffffff);
 	if (err) {
 		pr_err("%s/0: Oops: no 32bit PCI DMA ???\n", dev->name);
-		goto fail_ctrl;
+		goto fail_dma_set_mask;
 	}
 
 	err = request_irq(pci_dev->irq, cx23885_irq,
@@ -2173,7 +2175,7 @@
 	if (err < 0) {
 		pr_err("%s: can't get IRQ %d\n",
 		       dev->name, pci_dev->irq);
-		goto fail_irq;
+		goto fail_dma_set_mask;
 	}
 
 	switch (dev->board) {
@@ -2195,7 +2197,7 @@
 
 	return 0;
 
-fail_irq:
+fail_dma_set_mask:
 	cx23885_dev_unregister(dev);
 fail_ctrl:
 	v4l2_ctrl_handler_free(hdl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx23885/cx23885-dvb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx23885/cx23885-dvb.c
@@ -2459,16 +2459,10 @@
 			request_module("%s", info.type);
 			client_tuner = i2c_new_client_device(&dev->i2c_bus[1].i2c_adap, &info);
 			if (!i2c_client_has_driver(client_tuner)) {
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			if (!try_module_get(client_tuner->dev.driver->owner)) {
 				i2c_unregister_device(client_tuner);
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			port->i2c_client_tuner = client_tuner;
@@ -2505,16 +2499,10 @@
 			request_module("%s", info.type);
 			client_tuner = i2c_new_client_device(&dev->i2c_bus[1].i2c_adap, &info);
 			if (!i2c_client_has_driver(client_tuner)) {
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			if (!try_module_get(client_tuner->dev.driver->owner)) {
 				i2c_unregister_device(client_tuner);
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			port->i2c_client_tuner = client_tuner;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx23885/cx23885-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx23885/cx23885-video.c
@@ -342,6 +342,7 @@
 
 static int buffer_prepare(struct vb2_buffer *vb)
 {
+	int ret;
 	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
 	struct cx23885_dev *dev = vb->vb2_queue->drv_priv;
 	struct cx23885_buffer *buf =
@@ -358,12 +359,12 @@
 
 	switch (dev->field) {
 	case V4L2_FIELD_TOP:
-		cx23885_risc_buffer(dev->pci, &buf->risc,
+		ret = cx23885_risc_buffer(dev->pci, &buf->risc,
 				sgt->sgl, 0, UNSET,
 				buf->bpl, 0, dev->height);
 		break;
 	case V4L2_FIELD_BOTTOM:
-		cx23885_risc_buffer(dev->pci, &buf->risc,
+		ret = cx23885_risc_buffer(dev->pci, &buf->risc,
 				sgt->sgl, UNSET, 0,
 				buf->bpl, 0, dev->height);
 		break;
@@ -391,34 +392,34 @@
 			line0_offset = 0;
 			line1_offset = buf->bpl;
 		}
-		cx23885_risc_buffer(dev->pci, &buf->risc,
+		ret = cx23885_risc_buffer(dev->pci, &buf->risc,
 				sgt->sgl, line0_offset,
 				line1_offset,
 				buf->bpl, buf->bpl,
 				dev->height >> 1);
 		break;
 	case V4L2_FIELD_SEQ_TB:
-		cx23885_risc_buffer(dev->pci, &buf->risc,
+		ret = cx23885_risc_buffer(dev->pci, &buf->risc,
 				sgt->sgl,
 				0, buf->bpl * (dev->height >> 1),
 				buf->bpl, 0,
 				dev->height >> 1);
 		break;
 	case V4L2_FIELD_SEQ_BT:
-		cx23885_risc_buffer(dev->pci, &buf->risc,
+		ret = cx23885_risc_buffer(dev->pci, &buf->risc,
 				sgt->sgl,
 				buf->bpl * (dev->height >> 1), 0,
 				buf->bpl, 0,
 				dev->height >> 1);
 		break;
 	default:
-		BUG();
+		return -EINVAL; /* should not happen */
 	}
 	dprintk(2, "[%p/%d] buffer_init - %dx%d %dbpp 0x%08x - dma=0x%08lx\n",
 		buf, buf->vb.vb2_buf.index,
 		dev->width, dev->height, dev->fmt->depth, dev->fmt->fourcc,
 		(unsigned long)buf->risc.dma);
-	return 0;
+	return ret;
 }
 
 static void buffer_finish(struct vb2_buffer *vb)
@@ -1353,6 +1354,10 @@
 	/* register Video device */
 	dev->video_dev = cx23885_vdev_init(dev, dev->pci,
 		&cx23885_video_template, "video");
+	if (!dev->video_dev) {
+		err = -ENOMEM;
+		goto fail_unreg;
+	}
 	dev->video_dev->queue = &dev->vb2_vidq;
 	dev->video_dev->device_caps = V4L2_CAP_READWRITE | V4L2_CAP_STREAMING |
 				      V4L2_CAP_AUDIO | V4L2_CAP_VIDEO_CAPTURE;
@@ -1381,6 +1386,10 @@
 	/* register VBI device */
 	dev->vbi_dev = cx23885_vdev_init(dev, dev->pci,
 		&cx23885_vbi_template, "vbi");
+	if (!dev->vbi_dev) {
+		err = -ENOMEM;
+		goto fail_unreg;
+	}
 	dev->vbi_dev->queue = &dev->vb2_vbiq;
 	dev->vbi_dev->device_caps = V4L2_CAP_READWRITE | V4L2_CAP_STREAMING |
 				    V4L2_CAP_AUDIO | V4L2_CAP_VBI_CAPTURE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx25821/cx25821-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx25821/cx25821-core.c
@@ -1339,11 +1339,11 @@
 	struct cx25821_dev *dev = get_cx25821(v4l2_dev);
 
 	cx25821_shutdown(dev);
-	pci_disable_device(pci_dev);
 
 	/* unregister stuff */
 	if (pci_dev->irq)
 		free_irq(pci_dev->irq, dev);
+	pci_disable_device(pci_dev);
 
 	cx25821_dev_unregister(dev);
 	v4l2_device_unregister(v4l2_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx88/cx88-mpeg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx88/cx88-mpeg.c
@@ -162,6 +162,9 @@
 	cx_write(MO_TS_GPCNTRL, GP_COUNT_CONTROL_RESET);
 	q->count = 0;
 
+	/* clear interrupt status register */
+	cx_write(MO_TS_INTSTAT,  0x1f1111);
+
 	/* enable irqs */
 	dprintk(1, "setting the interrupt mask\n");
 	cx_set(MO_PCI_INTMSK, core->pci_irqmask | PCI_INT_TSINT);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx88/cx88-vbi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx88/cx88-vbi.c
@@ -144,11 +144,10 @@
 		return -EINVAL;
 	vb2_set_plane_payload(vb, 0, size);
 
-	cx88_risc_buffer(dev->pci, &buf->risc, sgt->sgl,
-			 0, VBI_LINE_LENGTH * lines,
-			 VBI_LINE_LENGTH, 0,
-			 lines);
-	return 0;
+	return cx88_risc_buffer(dev->pci, &buf->risc, sgt->sgl,
+				0, VBI_LINE_LENGTH * lines,
+				VBI_LINE_LENGTH, 0,
+				lines);
 }
 
 static void buffer_finish(struct vb2_buffer *vb)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/cx88/cx88-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/cx88/cx88-video.c
@@ -431,6 +431,7 @@
 
 static int buffer_prepare(struct vb2_buffer *vb)
 {
+	int ret;
 	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
 	struct cx8800_dev *dev = vb->vb2_queue->drv_priv;
 	struct cx88_core *core = dev->core;
@@ -445,35 +446,35 @@
 
 	switch (core->field) {
 	case V4L2_FIELD_TOP:
-		cx88_risc_buffer(dev->pci, &buf->risc,
-				 sgt->sgl, 0, UNSET,
-				 buf->bpl, 0, core->height);
+		ret = cx88_risc_buffer(dev->pci, &buf->risc,
+				       sgt->sgl, 0, UNSET,
+				       buf->bpl, 0, core->height);
 		break;
 	case V4L2_FIELD_BOTTOM:
-		cx88_risc_buffer(dev->pci, &buf->risc,
-				 sgt->sgl, UNSET, 0,
-				 buf->bpl, 0, core->height);
+		ret = cx88_risc_buffer(dev->pci, &buf->risc,
+				       sgt->sgl, UNSET, 0,
+				       buf->bpl, 0, core->height);
 		break;
 	case V4L2_FIELD_SEQ_TB:
-		cx88_risc_buffer(dev->pci, &buf->risc,
-				 sgt->sgl,
-				 0, buf->bpl * (core->height >> 1),
-				 buf->bpl, 0,
-				 core->height >> 1);
+		ret = cx88_risc_buffer(dev->pci, &buf->risc,
+				       sgt->sgl,
+				       0, buf->bpl * (core->height >> 1),
+				       buf->bpl, 0,
+				       core->height >> 1);
 		break;
 	case V4L2_FIELD_SEQ_BT:
-		cx88_risc_buffer(dev->pci, &buf->risc,
-				 sgt->sgl,
-				 buf->bpl * (core->height >> 1), 0,
-				 buf->bpl, 0,
-				 core->height >> 1);
+		ret = cx88_risc_buffer(dev->pci, &buf->risc,
+				       sgt->sgl,
+				       buf->bpl * (core->height >> 1), 0,
+				       buf->bpl, 0,
+				       core->height >> 1);
 		break;
 	case V4L2_FIELD_INTERLACED:
 	default:
-		cx88_risc_buffer(dev->pci, &buf->risc,
-				 sgt->sgl, 0, buf->bpl,
-				 buf->bpl, buf->bpl,
-				 core->height >> 1);
+		ret = cx88_risc_buffer(dev->pci, &buf->risc,
+				       sgt->sgl, 0, buf->bpl,
+				       buf->bpl, buf->bpl,
+				       core->height >> 1);
 		break;
 	}
 	dprintk(2,
@@ -481,7 +482,7 @@
 		buf, buf->vb.vb2_buf.index, __func__,
 		core->width, core->height, dev->fmt->depth, dev->fmt->fourcc,
 		(unsigned long)buf->risc.dma);
-	return 0;
+	return ret;
 }
 
 static void buffer_finish(struct vb2_buffer *vb)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ddbridge/ddbridge-dummy-fe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ddbridge/ddbridge-dummy-fe.c
@@ -112,7 +112,7 @@
 	state->frontend.demodulator_priv = state;
 	return &state->frontend;
 }
-EXPORT_SYMBOL(ddbridge_dummy_fe_qam_attach);
+EXPORT_SYMBOL_GPL(ddbridge_dummy_fe_qam_attach);
 
 static const struct dvb_frontend_ops ddbridge_dummy_fe_qam_ops = {
 	.delsys = { SYS_DVBC_ANNEX_A },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ddbridge/ddbridge-main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ddbridge/ddbridge-main.c
@@ -247,7 +247,7 @@
 	ddb_unmap(dev);
 	pci_set_drvdata(pdev, NULL);
 	pci_disable_device(pdev);
-	return -1;
+	return stat;
 }
 
 /****************************************************************************/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/dm1105/dm1105.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/dm1105/dm1105.c
@@ -1176,6 +1176,7 @@
 	struct dvb_demux *dvbdemux = &dev->demux;
 	struct dmx_demux *dmx = &dvbdemux->dmx;
 
+	cancel_work_sync(&dev->ir.work);
 	dm1105_ir_exit(dev);
 	dmx->close(dmx);
 	dvb_net_release(&dev->dvbnet);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/Kconfig
@@ -0,0 +1,20 @@
+config VIDEO_INTEL_IPU6
+	tristate "Intel IPU driver"
+	depends on ACPI
+	depends on MEDIA_SUPPORT
+	depends on MEDIA_PCI_SUPPORT
+	select IOMMU_API
+	select IOMMU_IOVA
+	select X86_DEV_DMA_OPS if X86
+	select VIDEOBUF2_DMA_CONTIG
+	select V4L2_FWNODE
+	select PHYS_ADDR_T_64BIT
+	select COMMON_CLK
+	help
+	  This is the Intel imaging processing unit, found in Intel SoCs and
+	  used for capturing images and video from a camera sensor.
+
+	  To compile this driver, say Y here! It contains 3 modules -
+	  intel_ipu6, intel_ipu6_isys and intel_ipu6_psys.
+
+source "drivers/media/pci/intel/ipu3/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/Makefile
@@ -3,4 +3,5 @@
 # Makefile for the IPU3 cio2 and ImGU drivers
 #
 
-obj-y	+= ipu3/
+obj-$(CONFIG_VIDEO_IPU3_CIO2)   += ipu3/
+obj-$(CONFIG_VIDEO_INTEL_IPU6)	+= ipu6/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-bus.c
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pci.h>
+#include <linux/pm_runtime.h>
+#include <linux/sizes.h>
+
+#include "ipu.h"
+#include "ipu-platform.h"
+#include "ipu-dma.h"
+
+#ifdef CONFIG_PM
+static struct bus_type ipu_bus;
+
+static int bus_pm_runtime_suspend(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	int rval;
+
+	rval = pm_generic_runtime_suspend(dev);
+	if (rval)
+		return rval;
+
+	rval = ipu_buttress_power(dev, adev->ctrl, false);
+	dev_dbg(dev, "%s: buttress power down %d\n", __func__, rval);
+	if (!rval)
+		return 0;
+
+	dev_err(dev, "power down failed!\n");
+
+	/* Powering down failed, attempt to resume device now */
+	rval = pm_generic_runtime_resume(dev);
+	if (!rval)
+		return -EBUSY;
+
+	return -EIO;
+}
+
+static int bus_pm_runtime_resume(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	int rval;
+
+	rval = ipu_buttress_power(dev, adev->ctrl, true);
+	dev_dbg(dev, "%s: buttress power up %d\n", __func__, rval);
+	if (rval)
+		return rval;
+
+	rval = pm_generic_runtime_resume(dev);
+	dev_dbg(dev, "%s: resume %d\n", __func__, rval);
+	if (rval)
+		goto out_err;
+
+	return 0;
+
+out_err:
+	ipu_buttress_power(dev, adev->ctrl, false);
+
+	return -EBUSY;
+}
+
+static const struct dev_pm_ops ipu_bus_pm_ops = {
+	.runtime_suspend = bus_pm_runtime_suspend,
+	.runtime_resume = bus_pm_runtime_resume,
+};
+
+#define IPU_BUS_PM_OPS	(&ipu_bus_pm_ops)
+#else
+#define IPU_BUS_PM_OPS	NULL
+#endif
+
+static int ipu_bus_match(struct device *dev, struct device_driver *drv)
+{
+	struct ipu_bus_driver *adrv = to_ipu_bus_driver(drv);
+
+	dev_dbg(dev, "bus match: \"%s\" --- \"%s\"\n", dev_name(dev),
+		adrv->wanted);
+
+	return !strncmp(dev_name(dev), adrv->wanted, strlen(adrv->wanted));
+}
+
+static int ipu_bus_probe(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_bus_driver *adrv = to_ipu_bus_driver(dev->driver);
+	int rval;
+
+	dev_dbg(dev, "bus probe dev %s\n", dev_name(dev));
+
+	adev->adrv = adrv;
+	if (!adrv->probe) {
+		rval = -ENODEV;
+		goto out_err;
+	}
+	rval = pm_runtime_get_sync(&adev->dev);
+	if (rval < 0) {
+		dev_err(&adev->dev, "Failed to get runtime PM\n");
+		goto out_err;
+	}
+
+	rval = adrv->probe(adev);
+	pm_runtime_put(&adev->dev);
+
+	if (rval)
+		goto out_err;
+
+	return 0;
+
+out_err:
+	ipu_bus_set_drvdata(adev, NULL);
+	adev->adrv = NULL;
+
+	return rval;
+}
+
+static void ipu_bus_remove(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_bus_driver *adrv = to_ipu_bus_driver(dev->driver);
+
+	if (adrv->remove)
+		adrv->remove(adev);
+}
+
+static struct bus_type ipu_bus = {
+	.name = IPU_BUS_NAME,
+	.match = ipu_bus_match,
+	.probe = ipu_bus_probe,
+	.remove = ipu_bus_remove,
+	.pm = IPU_BUS_PM_OPS,
+};
+
+static struct mutex ipu_bus_mutex;
+
+static void ipu_bus_release(struct device *dev)
+{
+}
+
+struct ipu_bus_device *ipu_bus_add_device(struct pci_dev *pdev,
+					  struct device *parent, void *pdata,
+					  struct ipu_buttress_ctrl *ctrl,
+					  char *name, unsigned int nr)
+{
+	struct ipu_bus_device *adev;
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+	int rval;
+
+	adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL);
+	if (!adev)
+		return ERR_PTR(-ENOMEM);
+
+	adev->dev.parent = parent;
+	adev->dev.bus = &ipu_bus;
+	adev->dev.release = ipu_bus_release;
+	adev->dev.dma_ops = &ipu_dma_ops;
+	adev->dma_mask = DMA_BIT_MASK(isp->secure_mode ?
+				      IPU_MMU_ADDRESS_BITS :
+				      IPU_MMU_ADDRESS_BITS_NON_SECURE);
+	adev->dev.dma_mask = &adev->dma_mask;
+	adev->dev.dma_parms = pdev->dev.dma_parms;
+	adev->dev.coherent_dma_mask = adev->dma_mask;
+	adev->ctrl = ctrl;
+	adev->pdata = pdata;
+	adev->isp = isp;
+	mutex_init(&adev->resume_lock);
+	dev_set_name(&adev->dev, "%s%d", name, nr);
+
+	rval = device_register(&adev->dev);
+	if (rval) {
+		put_device(&adev->dev);
+		return ERR_PTR(rval);
+	}
+
+	mutex_lock(&ipu_bus_mutex);
+	list_add(&adev->list, &isp->devices);
+	mutex_unlock(&ipu_bus_mutex);
+
+	pm_runtime_allow(&adev->dev);
+	pm_runtime_enable(&adev->dev);
+
+	return adev;
+}
+
+void ipu_bus_del_devices(struct pci_dev *pdev)
+{
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+	struct ipu_bus_device *adev, *save;
+
+	mutex_lock(&ipu_bus_mutex);
+
+	list_for_each_entry_safe(adev, save, &isp->devices, list) {
+		pm_runtime_disable(&adev->dev);
+		list_del(&adev->list);
+		device_unregister(&adev->dev);
+	}
+
+	mutex_unlock(&ipu_bus_mutex);
+}
+
+int ipu_bus_register_driver(struct ipu_bus_driver *adrv)
+{
+	adrv->drv.bus = &ipu_bus;
+	return driver_register(&adrv->drv);
+}
+EXPORT_SYMBOL(ipu_bus_register_driver);
+
+int ipu_bus_unregister_driver(struct ipu_bus_driver *adrv)
+{
+	driver_unregister(&adrv->drv);
+	return 0;
+}
+EXPORT_SYMBOL(ipu_bus_unregister_driver);
+
+int ipu_bus_register(void)
+{
+	mutex_init(&ipu_bus_mutex);
+	return bus_register(&ipu_bus);
+}
+
+void ipu_bus_unregister(void)
+{
+	mutex_destroy(&ipu_bus_mutex);
+	return bus_unregister(&ipu_bus);
+}
+
+static int flr_rpm_recovery(struct device *dev, void *p)
+{
+	dev_dbg(dev, "FLR recovery call\n");
+	/*
+	 * We are not necessarily going through device from child to
+	 * parent. runtime PM refuses to change state for parent if the child
+	 * is still active. At FLR (full reset for whole IPU) that doesn't
+	 * matter. Everything has been power gated by HW during the FLR cycle
+	 * and we are just cleaning up SW state. Thus, ignore child during
+	 * set_suspended.
+	 */
+	pm_suspend_ignore_children(dev, true);
+	pm_runtime_set_suspended(dev);
+	pm_suspend_ignore_children(dev, false);
+
+	return 0;
+}
+
+int ipu_bus_flr_recovery(void)
+{
+	bus_for_each_dev(&ipu_bus, NULL, NULL, flr_rpm_recovery);
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-bus.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-bus.h
@@ -0,0 +1,67 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_BUS_H
+#define IPU_BUS_H
+
+#include <linux/device.h>
+#include <linux/irqreturn.h>
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/pci.h>
+
+#define IPU_BUS_NAME	IPU_NAME "-bus"
+
+struct ipu_buttress_ctrl;
+struct ipu_subsystem_trace_config;
+
+struct ipu_bus_device {
+	struct device dev;
+	struct list_head list;
+	void *pdata;
+	struct ipu_bus_driver *adrv;
+	struct ipu_mmu *mmu;
+	struct ipu_device *isp;
+	struct ipu_subsystem_trace_config *trace_cfg;
+	struct ipu_buttress_ctrl *ctrl;
+	u64 dma_mask;
+	/* Protect runtime_resume calls on the dev */
+	struct mutex resume_lock;
+};
+
+#define to_ipu_bus_device(_dev) container_of(_dev, struct ipu_bus_device, dev)
+
+struct ipu_bus_driver {
+	struct device_driver drv;
+	const char *wanted;
+	int (*probe)(struct ipu_bus_device *adev);
+	void (*remove)(struct ipu_bus_device *adev);
+	irqreturn_t (*isr)(struct ipu_bus_device *adev);
+	irqreturn_t (*isr_threaded)(struct ipu_bus_device *adev);
+	bool wake_isr_thread;
+};
+
+#define to_ipu_bus_driver(_drv) container_of(_drv, struct ipu_bus_driver, drv)
+
+struct ipu_bus_device *ipu_bus_add_device(struct pci_dev *pdev,
+					  struct device *parent, void *pdata,
+					  struct ipu_buttress_ctrl *ctrl,
+					  char *name, unsigned int nr);
+void ipu_bus_del_devices(struct pci_dev *pdev);
+
+int ipu_bus_register_driver(struct ipu_bus_driver *adrv);
+int ipu_bus_unregister_driver(struct ipu_bus_driver *adrv);
+
+int ipu_bus_register(void);
+void ipu_bus_unregister(void);
+
+#define module_ipu_bus_driver(drv)			\
+	module_driver(drv, ipu_bus_register_driver, \
+		ipu_bus_unregister_driver)
+
+#define ipu_bus_set_drvdata(adev, data) dev_set_drvdata(&(adev)->dev, data)
+#define ipu_bus_get_drvdata(adev) dev_get_drvdata(&(adev)->dev)
+
+int ipu_bus_flr_recovery(void);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-buttress.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-buttress.c
@@ -0,0 +1,1396 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/completion.h>
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/elf.h>
+#include <linux/errno.h>
+#include <linux/firmware.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/pm_runtime.h>
+
+#include <media/ipu-isys.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-buttress.h"
+#include "ipu-platform-buttress-regs.h"
+#include "ipu-cpd.h"
+
+#define BOOTLOADER_STATUS_OFFSET       0x15c
+
+#define BOOTLOADER_MAGIC_KEY		0xb00710ad
+
+#define ENTRY	BUTTRESS_IU2CSECSR_IPC_PEER_COMP_ACTIONS_RST_PHASE1
+#define EXIT	BUTTRESS_IU2CSECSR_IPC_PEER_COMP_ACTIONS_RST_PHASE2
+#define QUERY	BUTTRESS_IU2CSECSR_IPC_PEER_QUERIED_IP_COMP_ACTIONS_RST_PHASE
+
+#define BUTTRESS_TSC_SYNC_RESET_TRIAL_MAX	10
+
+#define BUTTRESS_CSE_BOOTLOAD_TIMEOUT		5000000
+#define BUTTRESS_CSE_AUTHENTICATE_TIMEOUT	10000000
+#define BUTTRESS_CSE_FWRESET_TIMEOUT		100000
+
+#define BUTTRESS_IPC_TX_TIMEOUT			1000
+#define BUTTRESS_IPC_RESET_TIMEOUT		2000
+#define BUTTRESS_IPC_RX_TIMEOUT			1000
+#define BUTTRESS_IPC_VALIDITY_TIMEOUT		1000000
+#define BUTTRESS_TSC_SYNC_TIMEOUT		5000
+
+#define IPU_BUTTRESS_TSC_LIMIT	500	/* 26 us @ 19.2 MHz */
+#define IPU_BUTTRESS_TSC_RETRY	10
+
+#define BUTTRESS_CSE_IPC_RESET_RETRY	4
+
+#define BUTTRESS_IPC_CMD_SEND_RETRY	1
+
+static const u32 ipu_adev_irq_mask[] = {
+	BUTTRESS_ISR_IS_IRQ, BUTTRESS_ISR_PS_IRQ
+};
+
+int ipu_buttress_ipc_reset(struct ipu_device *isp, struct ipu_buttress_ipc *ipc)
+{
+	struct ipu_buttress *b = &isp->buttress;
+	unsigned int retries = BUTTRESS_IPC_RESET_TIMEOUT;
+	u32 val = 0, csr_in_clr;
+
+	if (!isp->secure_mode) {
+		dev_info(&isp->pdev->dev, "Skip ipc reset for non-secure mode");
+		return 0;
+	}
+
+	mutex_lock(&b->ipc_mutex);
+
+	/* Clear-by-1 CSR (all bits), corresponding internal states. */
+	val = readl(isp->base + ipc->csr_in);
+	writel(val, isp->base + ipc->csr_in);
+
+	/* Set peer CSR bit IPC_PEER_COMP_ACTIONS_RST_PHASE1 */
+	writel(ENTRY, isp->base + ipc->csr_out);
+	/*
+	 * Clear-by-1 all CSR bits EXCEPT following
+	 * bits:
+	 * A. IPC_PEER_COMP_ACTIONS_RST_PHASE1.
+	 * B. IPC_PEER_COMP_ACTIONS_RST_PHASE2.
+	 * C. Possibly custom bits, depending on
+	 * their role.
+	 */
+	csr_in_clr = BUTTRESS_IU2CSECSR_IPC_PEER_DEASSERTED_REG_VALID_REQ |
+		BUTTRESS_IU2CSECSR_IPC_PEER_ACKED_REG_VALID |
+		BUTTRESS_IU2CSECSR_IPC_PEER_ASSERTED_REG_VALID_REQ | QUERY;
+
+	while (retries--) {
+		usleep_range(400, 500);
+		val = readl(isp->base + ipc->csr_in);
+		switch (val) {
+		case (ENTRY | EXIT):
+		case (ENTRY | EXIT | QUERY):
+			dev_dbg(&isp->pdev->dev,
+				"%s:%s & %s\n", __func__,
+				"IPC_PEER_COMP_ACTIONS_RST_PHASE1",
+				"IPC_PEER_COMP_ACTIONS_RST_PHASE2");
+			/*
+			 * 1) Clear-by-1 CSR bits
+			 * (IPC_PEER_COMP_ACTIONS_RST_PHASE1,
+			 * IPC_PEER_COMP_ACTIONS_RST_PHASE2).
+			 * 2) Set peer CSR bit
+			 * IPC_PEER_QUERIED_IP_COMP_ACTIONS_RST_PHASE.
+			 */
+			writel(ENTRY | EXIT, isp->base + ipc->csr_in);
+			writel(QUERY, isp->base + ipc->csr_out);
+			break;
+		case ENTRY:
+		case (ENTRY | QUERY):
+			dev_dbg(&isp->pdev->dev,
+				"%s:IPC_PEER_COMP_ACTIONS_RST_PHASE1\n",
+				__func__);
+			/*
+			 * 1) Clear-by-1 CSR bits
+			 * (IPC_PEER_COMP_ACTIONS_RST_PHASE1,
+			 * IPC_PEER_QUERIED_IP_COMP_ACTIONS_RST_PHASE).
+			 * 2) Set peer CSR bit
+			 * IPC_PEER_COMP_ACTIONS_RST_PHASE1.
+			 */
+			writel(ENTRY | QUERY, isp->base + ipc->csr_in);
+			writel(ENTRY, isp->base + ipc->csr_out);
+			break;
+		case EXIT:
+		case (EXIT | QUERY):
+			dev_dbg(&isp->pdev->dev,
+				"%s: IPC_PEER_COMP_ACTIONS_RST_PHASE2\n",
+				__func__);
+			/*
+			 * Clear-by-1 CSR bit
+			 * IPC_PEER_COMP_ACTIONS_RST_PHASE2.
+			 * 1) Clear incoming doorbell.
+			 * 2) Clear-by-1 all CSR bits EXCEPT following
+			 * bits:
+			 * A. IPC_PEER_COMP_ACTIONS_RST_PHASE1.
+			 * B. IPC_PEER_COMP_ACTIONS_RST_PHASE2.
+			 * C. Possibly custom bits, depending on
+			 * their role.
+			 * 3) Set peer CSR bit
+			 * IPC_PEER_COMP_ACTIONS_RST_PHASE2.
+			 */
+			writel(EXIT, isp->base + ipc->csr_in);
+			writel(0, isp->base + ipc->db0_in);
+			writel(csr_in_clr, isp->base + ipc->csr_in);
+			writel(EXIT, isp->base + ipc->csr_out);
+
+			/*
+			 * Read csr_in again to make sure if RST_PHASE2 is done.
+			 * If csr_in is QUERY, it should be handled again.
+			 */
+			usleep_range(200, 300);
+			val = readl(isp->base + ipc->csr_in);
+			if (val & QUERY) {
+				dev_dbg(&isp->pdev->dev,
+					"%s: RST_PHASE2 retry csr_in = %x\n",
+					__func__, val);
+				break;
+			}
+			mutex_unlock(&b->ipc_mutex);
+			return 0;
+		case QUERY:
+			dev_dbg(&isp->pdev->dev,
+				"%s: %s\n", __func__,
+				"IPC_PEER_QUERIED_IP_COMP_ACTIONS_RST_PHASE");
+			/*
+			 * 1) Clear-by-1 CSR bit
+			 * IPC_PEER_QUERIED_IP_COMP_ACTIONS_RST_PHASE.
+			 * 2) Set peer CSR bit
+			 * IPC_PEER_COMP_ACTIONS_RST_PHASE1
+			 */
+			writel(QUERY, isp->base + ipc->csr_in);
+			writel(ENTRY, isp->base + ipc->csr_out);
+			break;
+		default:
+			dev_dbg_ratelimited(&isp->pdev->dev,
+					    "%s: unexpected CSR 0x%x\n",
+					    __func__, val);
+			break;
+		}
+	}
+
+	mutex_unlock(&b->ipc_mutex);
+	dev_err(&isp->pdev->dev, "Timed out while waiting for CSE\n");
+
+	return -ETIMEDOUT;
+}
+
+static void
+ipu_buttress_ipc_validity_close(struct ipu_device *isp,
+				struct ipu_buttress_ipc *ipc)
+{
+	/* Set bit 5 in CSE CSR */
+	writel(BUTTRESS_IU2CSECSR_IPC_PEER_DEASSERTED_REG_VALID_REQ,
+	       isp->base + ipc->csr_out);
+}
+
+static int
+ipu_buttress_ipc_validity_open(struct ipu_device *isp,
+			       struct ipu_buttress_ipc *ipc)
+{
+	unsigned int mask = BUTTRESS_IU2CSECSR_IPC_PEER_ACKED_REG_VALID;
+	unsigned int tout = BUTTRESS_IPC_VALIDITY_TIMEOUT;
+	void __iomem *addr;
+	int ret;
+	u32 val;
+
+	/* Set bit 3 in CSE CSR */
+	writel(BUTTRESS_IU2CSECSR_IPC_PEER_ASSERTED_REG_VALID_REQ,
+	       isp->base + ipc->csr_out);
+
+	addr = isp->base + ipc->csr_in;
+	ret = readl_poll_timeout(addr, val, val & mask, 200, tout);
+	if (ret) {
+		val = readl(addr);
+		dev_err(&isp->pdev->dev, "CSE validity timeout 0x%x\n", val);
+		ipu_buttress_ipc_validity_close(isp, ipc);
+	}
+
+	return ret;
+}
+
+static void ipu_buttress_ipc_recv(struct ipu_device *isp,
+				  struct ipu_buttress_ipc *ipc, u32 *ipc_msg)
+{
+	if (ipc_msg)
+		*ipc_msg = readl(isp->base + ipc->data0_in);
+	writel(0, isp->base + ipc->db0_in);
+}
+
+static int ipu_buttress_ipc_send_bulk(struct ipu_device *isp,
+				      enum ipu_buttress_ipc_domain ipc_domain,
+				      struct ipu_ipc_buttress_bulk_msg *msgs,
+				      u32 size)
+{
+	struct ipu_buttress *b = &isp->buttress;
+	struct ipu_buttress_ipc *ipc;
+	unsigned long tx_timeout_jiffies, rx_timeout_jiffies;
+	u32 val;
+	int ret;
+	int tout;
+	unsigned int i, retry = BUTTRESS_IPC_CMD_SEND_RETRY;
+
+	ipc = ipc_domain == IPU_BUTTRESS_IPC_CSE ? &b->cse : &b->ish;
+
+	mutex_lock(&b->ipc_mutex);
+
+	ret = ipu_buttress_ipc_validity_open(isp, ipc);
+	if (ret) {
+		dev_err(&isp->pdev->dev, "IPC validity open failed\n");
+		goto out;
+	}
+
+	tx_timeout_jiffies = msecs_to_jiffies(BUTTRESS_IPC_TX_TIMEOUT);
+	rx_timeout_jiffies = msecs_to_jiffies(BUTTRESS_IPC_RX_TIMEOUT);
+
+	for (i = 0; i < size; i++) {
+		reinit_completion(&ipc->send_complete);
+		if (msgs[i].require_resp)
+			reinit_completion(&ipc->recv_complete);
+
+		dev_dbg(&isp->pdev->dev, "bulk IPC command: 0x%x\n",
+			msgs[i].cmd);
+		writel(msgs[i].cmd, isp->base + ipc->data0_out);
+
+		val = BUTTRESS_IU2CSEDB0_BUSY | msgs[i].cmd_size;
+
+		writel(val, isp->base + ipc->db0_out);
+
+		tout = wait_for_completion_timeout(&ipc->send_complete,
+						   tx_timeout_jiffies);
+		if (!tout) {
+			dev_err(&isp->pdev->dev, "send IPC response timeout\n");
+			if (!retry--) {
+				ret = -ETIMEDOUT;
+				goto out;
+			}
+
+			/*
+			 * WORKAROUND: Sometimes CSE is not
+			 * responding on first try, try again.
+			 */
+			writel(0, isp->base + ipc->db0_out);
+			i--;
+			continue;
+		}
+
+		retry = BUTTRESS_IPC_CMD_SEND_RETRY;
+
+		if (!msgs[i].require_resp)
+			continue;
+
+		tout = wait_for_completion_timeout(&ipc->recv_complete,
+						   rx_timeout_jiffies);
+		if (!tout) {
+			dev_err(&isp->pdev->dev, "recv IPC response timeout\n");
+			ret = -ETIMEDOUT;
+			goto out;
+		}
+
+		if (ipc->nack_mask &&
+		    (ipc->recv_data & ipc->nack_mask) == ipc->nack) {
+			dev_err(&isp->pdev->dev,
+				"IPC NACK for cmd 0x%x\n", msgs[i].cmd);
+			ret = -ENODEV;
+			goto out;
+		}
+
+		if (ipc->recv_data != msgs[i].expected_resp) {
+			dev_err(&isp->pdev->dev,
+				"expected resp: 0x%x, IPC response: 0x%x ",
+				msgs[i].expected_resp, ipc->recv_data);
+			ret = -EIO;
+			goto out;
+		}
+	}
+
+	dev_dbg(&isp->pdev->dev, "bulk IPC commands done\n");
+
+out:
+	ipu_buttress_ipc_validity_close(isp, ipc);
+	mutex_unlock(&b->ipc_mutex);
+	return ret;
+}
+
+static int
+ipu_buttress_ipc_send(struct ipu_device *isp,
+		      enum ipu_buttress_ipc_domain ipc_domain,
+		      u32 ipc_msg, u32 size, bool require_resp,
+		      u32 expected_resp)
+{
+	struct ipu_ipc_buttress_bulk_msg msg = {
+		.cmd = ipc_msg,
+		.cmd_size = size,
+		.require_resp = require_resp,
+		.expected_resp = expected_resp,
+	};
+
+	return ipu_buttress_ipc_send_bulk(isp, ipc_domain, &msg, 1);
+}
+
+static irqreturn_t ipu_buttress_call_isr(struct ipu_bus_device *adev)
+{
+	irqreturn_t ret = IRQ_WAKE_THREAD;
+
+	if (!adev || !adev->adrv)
+		return IRQ_NONE;
+
+	if (adev->adrv->isr)
+		ret = adev->adrv->isr(adev);
+
+	if (ret == IRQ_WAKE_THREAD && !adev->adrv->isr_threaded)
+		ret = IRQ_NONE;
+
+	adev->adrv->wake_isr_thread = (ret == IRQ_WAKE_THREAD);
+
+	return ret;
+}
+
+irqreturn_t ipu_buttress_isr(int irq, void *isp_ptr)
+{
+	struct ipu_device *isp = isp_ptr;
+	struct ipu_bus_device *adev[] = { isp->isys, isp->psys };
+	struct ipu_buttress *b = &isp->buttress;
+	irqreturn_t ret = IRQ_NONE;
+	u32 disable_irqs = 0;
+	u32 irq_status;
+	u32 reg_irq_sts = BUTTRESS_REG_ISR_STATUS;
+	unsigned int i;
+
+	pm_runtime_get(&isp->pdev->dev);
+
+	if (!pm_runtime_active(&isp->pdev->dev)) {
+		irq_status = readl(isp->base + reg_irq_sts);
+		writel(irq_status, isp->base + BUTTRESS_REG_ISR_CLEAR);
+		pm_runtime_put(&isp->pdev->dev);
+		return IRQ_HANDLED;
+	}
+
+	irq_status = readl(isp->base + reg_irq_sts);
+	if (!irq_status) {
+		pm_runtime_put(&isp->pdev->dev);
+		return IRQ_NONE;
+	}
+
+	do {
+		writel(irq_status, isp->base + BUTTRESS_REG_ISR_CLEAR);
+
+		for (i = 0; i < ARRAY_SIZE(ipu_adev_irq_mask); i++) {
+			if (irq_status & ipu_adev_irq_mask[i]) {
+				irqreturn_t r = ipu_buttress_call_isr(adev[i]);
+
+				if (r == IRQ_WAKE_THREAD) {
+					ret = IRQ_WAKE_THREAD;
+					disable_irqs |= ipu_adev_irq_mask[i];
+				} else if (ret == IRQ_NONE &&
+					   r == IRQ_HANDLED) {
+					ret = IRQ_HANDLED;
+				}
+			}
+		}
+
+		if (irq_status & (BUTTRESS_ISR_IPC_FROM_CSE_IS_WAITING |
+				  BUTTRESS_ISR_IPC_FROM_ISH_IS_WAITING |
+				  BUTTRESS_ISR_IPC_EXEC_DONE_BY_CSE |
+				  BUTTRESS_ISR_IPC_EXEC_DONE_BY_ISH |
+				  BUTTRESS_ISR_SAI_VIOLATION) &&
+		    ret == IRQ_NONE)
+			ret = IRQ_HANDLED;
+
+		if (irq_status & BUTTRESS_ISR_IPC_FROM_CSE_IS_WAITING) {
+			dev_dbg(&isp->pdev->dev,
+				"BUTTRESS_ISR_IPC_FROM_CSE_IS_WAITING\n");
+			ipu_buttress_ipc_recv(isp, &b->cse, &b->cse.recv_data);
+			complete(&b->cse.recv_complete);
+		}
+
+		if (irq_status & BUTTRESS_ISR_IPC_FROM_ISH_IS_WAITING) {
+			dev_dbg(&isp->pdev->dev,
+				"BUTTRESS_ISR_IPC_FROM_ISH_IS_WAITING\n");
+			ipu_buttress_ipc_recv(isp, &b->ish, &b->ish.recv_data);
+			complete(&b->ish.recv_complete);
+		}
+
+		if (irq_status & BUTTRESS_ISR_IPC_EXEC_DONE_BY_CSE) {
+			dev_dbg(&isp->pdev->dev,
+				"BUTTRESS_ISR_IPC_EXEC_DONE_BY_CSE\n");
+			complete(&b->cse.send_complete);
+		}
+
+		if (irq_status & BUTTRESS_ISR_IPC_EXEC_DONE_BY_ISH) {
+			dev_dbg(&isp->pdev->dev,
+				"BUTTRESS_ISR_IPC_EXEC_DONE_BY_CSE\n");
+			complete(&b->ish.send_complete);
+		}
+
+		if (irq_status & BUTTRESS_ISR_SAI_VIOLATION &&
+		    ipu_buttress_get_secure_mode(isp)) {
+			dev_err(&isp->pdev->dev,
+				"BUTTRESS_ISR_SAI_VIOLATION\n");
+			WARN_ON(1);
+		}
+
+		irq_status = readl(isp->base + reg_irq_sts);
+	} while (irq_status && !isp->flr_done);
+
+	if (disable_irqs)
+		writel(BUTTRESS_IRQS & ~disable_irqs,
+		       isp->base + BUTTRESS_REG_ISR_ENABLE);
+
+	pm_runtime_put(&isp->pdev->dev);
+
+	return ret;
+}
+
+irqreturn_t ipu_buttress_isr_threaded(int irq, void *isp_ptr)
+{
+	struct ipu_device *isp = isp_ptr;
+	struct ipu_bus_device *adev[] = { isp->isys, isp->psys };
+	irqreturn_t ret = IRQ_NONE;
+	unsigned int i;
+
+	dev_dbg(&isp->pdev->dev, "isr: Buttress threaded interrupt handler\n");
+
+	for (i = 0; i < ARRAY_SIZE(ipu_adev_irq_mask); i++) {
+		if (adev[i] && adev[i]->adrv &&
+		    adev[i]->adrv->wake_isr_thread &&
+		    adev[i]->adrv->isr_threaded(adev[i]) == IRQ_HANDLED)
+			ret = IRQ_HANDLED;
+	}
+
+	writel(BUTTRESS_IRQS, isp->base + BUTTRESS_REG_ISR_ENABLE);
+
+	return ret;
+}
+
+int ipu_buttress_power(struct device *dev,
+		       struct ipu_buttress_ctrl *ctrl, bool on)
+{
+	struct ipu_device *isp = to_ipu_bus_device(dev)->isp;
+	u32 pwr_sts, val;
+	int ret = 0;
+
+	if (!ctrl)
+		return 0;
+
+	/* Until FLR completion nothing is expected to work */
+	if (isp->flr_done)
+		return 0;
+
+	mutex_lock(&isp->buttress.power_mutex);
+
+	if (!on) {
+		val = 0;
+		pwr_sts = ctrl->pwr_sts_off << ctrl->pwr_sts_shift;
+	} else {
+		val = BUTTRESS_FREQ_CTL_START |
+			ctrl->divisor << ctrl->divisor_shift |
+			ctrl->qos_floor << BUTTRESS_FREQ_CTL_QOS_FLOOR_SHIFT |
+			BUTTRESS_FREQ_CTL_ICCMAX_LEVEL;
+
+		pwr_sts = ctrl->pwr_sts_on << ctrl->pwr_sts_shift;
+	}
+
+	writel(val, isp->base + ctrl->freq_ctl);
+
+	ret = readl_poll_timeout(isp->base + BUTTRESS_REG_PWR_STATE,
+				 val, ((val & ctrl->pwr_sts_mask) == pwr_sts),
+				 100, BUTTRESS_POWER_TIMEOUT);
+	if (ret)
+		dev_err(&isp->pdev->dev,
+			"Change power status timeout with 0x%x\n", val);
+
+	ctrl->started = !ret && on;
+
+	mutex_unlock(&isp->buttress.power_mutex);
+
+	return ret;
+}
+
+static bool secure_mode_enable = 1;
+module_param(secure_mode_enable, bool, 0660);
+MODULE_PARM_DESC(secure_mode, "IPU secure mode enable");
+
+void ipu_buttress_set_secure_mode(struct ipu_device *isp)
+{
+	u8 retry = 100;
+	u32 val, read;
+
+	/*
+	 * HACK to disable possible secure mode. This can be
+	 * reverted when CSE is disabling the secure mode
+	 */
+	read = readl(isp->base + BUTTRESS_REG_SECURITY_CTL);
+
+	if (secure_mode_enable)
+		val = read |= BUTTRESS_SECURITY_CTL_FW_SECURE_MODE;
+	else
+		val = read & ~BUTTRESS_SECURITY_CTL_FW_SECURE_MODE;
+
+	if (val == read)
+		return;
+
+	writel(val, isp->base + BUTTRESS_REG_SECURITY_CTL);
+
+	/* In B0, for some registers in buttress, because of a hw bug, write
+	 * might not succeed at first attempt. Write twice until the
+	 * write is successful
+	 */
+	writel(val, isp->base + BUTTRESS_REG_SECURITY_CTL);
+
+	while (retry--) {
+		read = readl(isp->base + BUTTRESS_REG_SECURITY_CTL);
+		if (read == val)
+			break;
+
+		writel(val, isp->base + BUTTRESS_REG_SECURITY_CTL);
+
+		if (retry == 0)
+			dev_err(&isp->pdev->dev,
+				"update security control register failed\n");
+	}
+}
+
+bool ipu_buttress_get_secure_mode(struct ipu_device *isp)
+{
+	u32 val;
+
+	val = readl(isp->base + BUTTRESS_REG_SECURITY_CTL);
+
+	return val & BUTTRESS_SECURITY_CTL_FW_SECURE_MODE;
+}
+
+bool ipu_buttress_auth_done(struct ipu_device *isp)
+{
+	u32 val;
+
+	if (!isp->secure_mode)
+		return 1;
+
+	val = readl(isp->base + BUTTRESS_REG_SECURITY_CTL);
+
+	return (val & BUTTRESS_SECURITY_CTL_FW_SETUP_MASK) ==
+	    BUTTRESS_SECURITY_CTL_AUTH_DONE;
+}
+EXPORT_SYMBOL(ipu_buttress_auth_done);
+
+static void ipu_buttress_set_psys_ratio(struct ipu_device *isp,
+					unsigned int psys_divisor,
+					unsigned int psys_qos_floor)
+{
+	struct ipu_buttress_ctrl *ctrl = isp->psys->ctrl;
+
+	mutex_lock(&isp->buttress.power_mutex);
+
+	if (ctrl->divisor == psys_divisor && ctrl->qos_floor == psys_qos_floor)
+		goto out_mutex_unlock;
+
+	ctrl->divisor = psys_divisor;
+	ctrl->qos_floor = psys_qos_floor;
+
+	if (ctrl->started) {
+		/*
+		 * According to documentation driver initiates DVFS
+		 * transition by writing wanted ratio, floor ratio and start
+		 * bit. No need to stop PS first
+		 */
+		writel(BUTTRESS_FREQ_CTL_START |
+		       ctrl->qos_floor << BUTTRESS_FREQ_CTL_QOS_FLOOR_SHIFT |
+		       psys_divisor, isp->base + BUTTRESS_REG_PS_FREQ_CTL);
+	}
+
+out_mutex_unlock:
+	mutex_unlock(&isp->buttress.power_mutex);
+}
+
+static void ipu_buttress_set_isys_ratio(struct ipu_device *isp,
+					unsigned int isys_divisor)
+{
+	struct ipu_buttress_ctrl *ctrl = isp->isys->ctrl;
+
+	mutex_lock(&isp->buttress.power_mutex);
+
+	if (ctrl->divisor == isys_divisor)
+		goto out_mutex_unlock;
+
+	ctrl->divisor = isys_divisor;
+
+	if (ctrl->started) {
+		writel(BUTTRESS_FREQ_CTL_START |
+		       ctrl->qos_floor << BUTTRESS_FREQ_CTL_QOS_FLOOR_SHIFT |
+		       isys_divisor, isp->base + BUTTRESS_REG_IS_FREQ_CTL);
+	}
+
+out_mutex_unlock:
+	mutex_unlock(&isp->buttress.power_mutex);
+}
+
+static void ipu_buttress_set_psys_freq(struct ipu_device *isp,
+				       unsigned int freq)
+{
+	unsigned int psys_ratio = freq / BUTTRESS_PS_FREQ_STEP;
+
+	if (isp->buttress.psys_force_ratio)
+		return;
+
+	ipu_buttress_set_psys_ratio(isp, psys_ratio, psys_ratio);
+}
+
+void
+ipu_buttress_add_psys_constraint(struct ipu_device *isp,
+				 struct ipu_buttress_constraint *constraint)
+{
+	struct ipu_buttress *b = &isp->buttress;
+
+	mutex_lock(&b->cons_mutex);
+	list_add(&constraint->list, &b->constraints);
+
+	if (constraint->min_freq > b->psys_min_freq) {
+		isp->buttress.psys_min_freq = min(constraint->min_freq,
+						  b->psys_fused_freqs.max_freq);
+		ipu_buttress_set_psys_freq(isp, b->psys_min_freq);
+	}
+	mutex_unlock(&b->cons_mutex);
+}
+EXPORT_SYMBOL_GPL(ipu_buttress_add_psys_constraint);
+
+void
+ipu_buttress_remove_psys_constraint(struct ipu_device *isp,
+				    struct ipu_buttress_constraint *constraint)
+{
+	struct ipu_buttress *b = &isp->buttress;
+	struct ipu_buttress_constraint *c;
+	unsigned int min_freq = 0;
+
+	mutex_lock(&b->cons_mutex);
+	list_del(&constraint->list);
+
+	if (constraint->min_freq >= b->psys_min_freq) {
+		list_for_each_entry(c, &b->constraints, list)
+			if (c->min_freq > min_freq)
+				min_freq = c->min_freq;
+
+		b->psys_min_freq = clamp(min_freq,
+					 b->psys_fused_freqs.efficient_freq,
+					 b->psys_fused_freqs.max_freq);
+		ipu_buttress_set_psys_freq(isp, b->psys_min_freq);
+	}
+	mutex_unlock(&b->cons_mutex);
+}
+EXPORT_SYMBOL_GPL(ipu_buttress_remove_psys_constraint);
+
+int ipu_buttress_reset_authentication(struct ipu_device *isp)
+{
+	int ret;
+	u32 val;
+
+	if (!isp->secure_mode) {
+		dev_dbg(&isp->pdev->dev,
+			"Non-secure mode -> skip authentication\n");
+		return 0;
+	}
+
+	writel(BUTTRESS_FW_RESET_CTL_START, isp->base +
+	       BUTTRESS_REG_FW_RESET_CTL);
+
+	ret = readl_poll_timeout(isp->base + BUTTRESS_REG_FW_RESET_CTL, val,
+				 val & BUTTRESS_FW_RESET_CTL_DONE, 500,
+				 BUTTRESS_CSE_FWRESET_TIMEOUT);
+	if (ret) {
+		dev_err(&isp->pdev->dev,
+			"Time out while resetting authentication state\n");
+	} else {
+		dev_info(&isp->pdev->dev,
+			 "FW reset for authentication done\n");
+		writel(0, isp->base + BUTTRESS_REG_FW_RESET_CTL);
+		/* leave some time for HW restore */
+		usleep_range(800, 1000);
+	}
+
+	return ret;
+}
+
+int ipu_buttress_map_fw_image(struct ipu_bus_device *sys,
+			      const struct firmware *fw, struct sg_table *sgt)
+{
+	struct page **pages;
+	const void *addr;
+	unsigned long n_pages, i;
+	int rval;
+
+	n_pages = PAGE_ALIGN(fw->size) >> PAGE_SHIFT;
+
+	pages = kmalloc_array(n_pages, sizeof(*pages), GFP_KERNEL);
+	if (!pages)
+		return -ENOMEM;
+
+	addr = fw->data;
+	for (i = 0; i < n_pages; i++) {
+		struct page *p = vmalloc_to_page(addr);
+
+		if (!p) {
+			rval = -ENODEV;
+			goto out;
+		}
+		pages[i] = p;
+		addr += PAGE_SIZE;
+	}
+
+	rval = sg_alloc_table_from_pages(sgt, pages, n_pages, 0, fw->size,
+					 GFP_KERNEL);
+	if (rval) {
+		rval = -ENOMEM;
+		goto out;
+	}
+
+	n_pages = dma_map_sg(&sys->dev, sgt->sgl, sgt->nents, DMA_TO_DEVICE);
+	if (n_pages != sgt->nents) {
+		rval = -ENOMEM;
+		sg_free_table(sgt);
+		goto out;
+	}
+
+	dma_sync_sg_for_device(&sys->dev, sgt->sgl, sgt->nents, DMA_TO_DEVICE);
+
+out:
+	kfree(pages);
+
+	return rval;
+}
+EXPORT_SYMBOL_GPL(ipu_buttress_map_fw_image);
+
+int ipu_buttress_unmap_fw_image(struct ipu_bus_device *sys,
+				struct sg_table *sgt)
+{
+	dma_unmap_sg(&sys->dev, sgt->sgl, sgt->nents, DMA_TO_DEVICE);
+	sg_free_table(sgt);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_buttress_unmap_fw_image);
+
+int ipu_buttress_authenticate(struct ipu_device *isp)
+{
+	struct ipu_psys_pdata *psys_pdata;
+	struct ipu_buttress *b = &isp->buttress;
+	u32 data, mask, done, fail;
+	int rval;
+
+	if (!isp->secure_mode) {
+		dev_dbg(&isp->pdev->dev,
+			"Non-secure mode -> skip authentication\n");
+		return 0;
+	}
+
+	psys_pdata = isp->psys->pdata;
+
+	mutex_lock(&b->auth_mutex);
+
+	if (ipu_buttress_auth_done(isp)) {
+		rval = 0;
+		goto iunit_power_off;
+	}
+
+	/*
+	 * Write address of FIT table to FW_SOURCE register
+	 * Let's use fw address. I.e. not using FIT table yet
+	 */
+	data = lower_32_bits(isp->pkg_dir_dma_addr);
+	writel(data, isp->base + BUTTRESS_REG_FW_SOURCE_BASE_LO);
+
+	data = upper_32_bits(isp->pkg_dir_dma_addr);
+	writel(data, isp->base + BUTTRESS_REG_FW_SOURCE_BASE_HI);
+
+	/*
+	 * Write boot_load into IU2CSEDATA0
+	 * Write sizeof(boot_load) | 0x2 << CLIENT_ID to
+	 * IU2CSEDB.IU2CSECMD and set IU2CSEDB.IU2CSEBUSY as
+	 */
+	dev_info(&isp->pdev->dev, "Sending BOOT_LOAD to CSE\n");
+	rval = ipu_buttress_ipc_send(isp, IPU_BUTTRESS_IPC_CSE,
+				     BUTTRESS_IU2CSEDATA0_IPC_BOOT_LOAD,
+				     1, 1,
+				     BUTTRESS_CSE2IUDATA0_IPC_BOOT_LOAD_DONE);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "CSE boot_load failed\n");
+		goto iunit_power_off;
+	}
+
+	mask = BUTTRESS_SECURITY_CTL_FW_SETUP_MASK;
+	done = BUTTRESS_SECURITY_CTL_FW_SETUP_DONE;
+	fail = BUTTRESS_SECURITY_CTL_AUTH_FAILED;
+	rval = readl_poll_timeout(isp->base + BUTTRESS_REG_SECURITY_CTL, data,
+				  ((data & mask) == done ||
+				   (data & mask) == fail), 500,
+				  BUTTRESS_CSE_BOOTLOAD_TIMEOUT);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "CSE boot_load timeout\n");
+		goto iunit_power_off;
+	}
+
+	data = readl(isp->base + BUTTRESS_REG_SECURITY_CTL) & mask;
+	if (data == fail) {
+		dev_err(&isp->pdev->dev, "CSE auth failed\n");
+		rval = -EINVAL;
+		goto iunit_power_off;
+	}
+
+	rval = readl_poll_timeout(psys_pdata->base + BOOTLOADER_STATUS_OFFSET,
+				  data, data == BOOTLOADER_MAGIC_KEY, 500,
+				  BUTTRESS_CSE_BOOTLOAD_TIMEOUT);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Expect magic number timeout 0x%x\n",
+			data);
+		goto iunit_power_off;
+	}
+
+	/*
+	 * Write authenticate_run into IU2CSEDATA0
+	 * Write sizeof(boot_load) | 0x2 << CLIENT_ID to
+	 * IU2CSEDB.IU2CSECMD and set IU2CSEDB.IU2CSEBUSY as
+	 */
+	dev_info(&isp->pdev->dev, "Sending AUTHENTICATE_RUN to CSE\n");
+	rval = ipu_buttress_ipc_send(isp, IPU_BUTTRESS_IPC_CSE,
+				     BUTTRESS_IU2CSEDATA0_IPC_AUTH_RUN,
+				     1, 1,
+				     BUTTRESS_CSE2IUDATA0_IPC_AUTH_RUN_DONE);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "CSE authenticate_run failed\n");
+		goto iunit_power_off;
+	}
+
+	done = BUTTRESS_SECURITY_CTL_AUTH_DONE;
+	rval = readl_poll_timeout(isp->base + BUTTRESS_REG_SECURITY_CTL, data,
+				  ((data & mask) == done ||
+				   (data & mask) == fail), 500,
+				  BUTTRESS_CSE_AUTHENTICATE_TIMEOUT);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "CSE authenticate timeout\n");
+		goto iunit_power_off;
+	}
+
+	data = readl(isp->base + BUTTRESS_REG_SECURITY_CTL) & mask;
+	if (data == fail) {
+		dev_err(&isp->pdev->dev, "CSE boot_load failed\n");
+		rval = -EINVAL;
+		goto iunit_power_off;
+	}
+
+	dev_info(&isp->pdev->dev, "CSE authenticate_run done\n");
+
+iunit_power_off:
+	mutex_unlock(&b->auth_mutex);
+
+	return rval;
+}
+
+static int ipu_buttress_send_tsc_request(struct ipu_device *isp)
+{
+	u32 val, mask, shift, done;
+	int ret;
+
+	mask = BUTTRESS_PWR_STATE_HH_STATUS_MASK;
+	shift = BUTTRESS_PWR_STATE_HH_STATUS_SHIFT;
+
+	writel(BUTTRESS_FABRIC_CMD_START_TSC_SYNC,
+	       isp->base + BUTTRESS_REG_FABRIC_CMD);
+
+	val = readl(isp->base + BUTTRESS_REG_PWR_STATE);
+	val = (val & mask) >> shift;
+	if (val == BUTTRESS_PWR_STATE_HH_STATE_ERR) {
+		dev_err(&isp->pdev->dev, "Start tsc sync failed\n");
+		return -EINVAL;
+	}
+
+	done = BUTTRESS_PWR_STATE_HH_STATE_DONE;
+	ret = readl_poll_timeout(isp->base + BUTTRESS_REG_PWR_STATE, val,
+				 ((val & mask) >> shift == done), 500,
+				 BUTTRESS_TSC_SYNC_TIMEOUT);
+	if (ret)
+		dev_err(&isp->pdev->dev, "Start tsc sync timeout\n");
+
+	return ret;
+}
+
+int ipu_buttress_start_tsc_sync(struct ipu_device *isp)
+{
+	unsigned int i;
+
+	for (i = 0; i < BUTTRESS_TSC_SYNC_RESET_TRIAL_MAX; i++) {
+		int ret;
+
+		ret = ipu_buttress_send_tsc_request(isp);
+		if (ret == -ETIMEDOUT) {
+			u32 val;
+			/* set tsw soft reset */
+			val = readl(isp->base + BUTTRESS_REG_TSW_CTL);
+			val = val | BUTTRESS_TSW_CTL_SOFT_RESET;
+			writel(val, isp->base + BUTTRESS_REG_TSW_CTL);
+			/* clear tsw soft reset */
+			val = val & (~BUTTRESS_TSW_CTL_SOFT_RESET);
+			writel(val, isp->base + BUTTRESS_REG_TSW_CTL);
+
+			continue;
+		}
+		return ret;
+	}
+
+	dev_err(&isp->pdev->dev, "TSC sync failed(timeout)\n");
+
+	return -ETIMEDOUT;
+}
+EXPORT_SYMBOL(ipu_buttress_start_tsc_sync);
+
+struct clk_ipu_sensor {
+	struct ipu_device *isp;
+	struct clk_hw hw;
+	unsigned int id;
+	unsigned long rate;
+};
+
+#define to_clk_ipu_sensor(_hw) container_of(_hw, struct clk_ipu_sensor, hw)
+
+int ipu_buttress_tsc_read(struct ipu_device *isp, u64 *val)
+{
+	u32 tsc_hi_1, tsc_hi_2, tsc_lo;
+	unsigned long flags;
+
+	local_irq_save(flags);
+	tsc_hi_1 = readl(isp->base + BUTTRESS_REG_TSC_HI);
+	tsc_lo = readl(isp->base + BUTTRESS_REG_TSC_LO);
+	tsc_hi_2 = readl(isp->base + BUTTRESS_REG_TSC_HI);
+	if (tsc_hi_1 == tsc_hi_2) {
+		*val = (u64)tsc_hi_1 << 32 | tsc_lo;
+	} else {
+		/* Check if TSC has rolled over */
+		if (tsc_lo & BIT(31))
+			*val = (u64)tsc_hi_1 << 32 | tsc_lo;
+		else
+			*val = (u64)tsc_hi_2 << 32 | tsc_lo;
+	}
+	local_irq_restore(flags);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_buttress_tsc_read);
+
+#ifdef CONFIG_DEBUG_FS
+
+static int ipu_buttress_reg_open(struct inode *inode, struct file *file)
+{
+	if (!inode->i_private)
+		return -EACCES;
+
+	file->private_data = inode->i_private;
+	return 0;
+}
+
+static ssize_t ipu_buttress_reg_read(struct file *file, char __user *buf,
+				     size_t count, loff_t *ppos)
+{
+	struct debugfs_reg32 *reg = file->private_data;
+	u8 tmp[11];
+	u32 val = readl((void __iomem *)reg->offset);
+	int len = scnprintf(tmp, sizeof(tmp), "0x%08x", val);
+
+	return simple_read_from_buffer(buf, len, ppos, &tmp, len);
+}
+
+static ssize_t ipu_buttress_reg_write(struct file *file,
+				      const char __user *buf,
+				      size_t count, loff_t *ppos)
+{
+	struct debugfs_reg32 *reg = file->private_data;
+	u32 val;
+	int rval;
+
+	rval = kstrtou32_from_user(buf, count, 0, &val);
+	if (rval)
+		return rval;
+
+	writel(val, (void __iomem *)reg->offset);
+
+	return count;
+}
+
+static struct debugfs_reg32 buttress_regs[] = {
+	{"IU2CSEDB0", BUTTRESS_REG_IU2CSEDB0},
+	{"IU2CSEDATA0", BUTTRESS_REG_IU2CSEDATA0},
+	{"CSE2IUDB0", BUTTRESS_REG_CSE2IUDB0},
+	{"CSE2IUDATA0", BUTTRESS_REG_CSE2IUDATA0},
+	{"CSE2IUCSR", BUTTRESS_REG_CSE2IUCSR},
+	{"IU2CSECSR", BUTTRESS_REG_IU2CSECSR},
+};
+
+static const struct file_operations ipu_buttress_reg_fops = {
+	.owner = THIS_MODULE,
+	.open = ipu_buttress_reg_open,
+	.read = ipu_buttress_reg_read,
+	.write = ipu_buttress_reg_write,
+};
+
+static int ipu_buttress_start_tsc_sync_set(void *data, u64 val)
+{
+	struct ipu_device *isp = data;
+
+	return ipu_buttress_start_tsc_sync(isp);
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(ipu_buttress_start_tsc_sync_fops, NULL,
+			ipu_buttress_start_tsc_sync_set, "%llu\n");
+
+static int ipu_buttress_tsc_get(void *data, u64 *val)
+{
+	return ipu_buttress_tsc_read(data, val);
+}
+DEFINE_SIMPLE_ATTRIBUTE(ipu_buttress_tsc_fops, ipu_buttress_tsc_get,
+			NULL, "%llu\n");
+
+static int ipu_buttress_psys_force_freq_get(void *data, u64 *val)
+{
+	struct ipu_device *isp = data;
+
+	*val = isp->buttress.psys_force_ratio * BUTTRESS_PS_FREQ_STEP;
+
+	return 0;
+}
+
+static int ipu_buttress_psys_force_freq_set(void *data, u64 val)
+{
+	struct ipu_device *isp = data;
+
+	if (val && (val < BUTTRESS_MIN_FORCE_PS_FREQ ||
+		    val > BUTTRESS_MAX_FORCE_PS_FREQ))
+		return -EINVAL;
+
+	do_div(val, BUTTRESS_PS_FREQ_STEP);
+	isp->buttress.psys_force_ratio = val;
+
+	if (isp->buttress.psys_force_ratio)
+		ipu_buttress_set_psys_ratio(isp,
+					    isp->buttress.psys_force_ratio,
+					    isp->buttress.psys_force_ratio);
+	else
+		ipu_buttress_set_psys_freq(isp, isp->buttress.psys_min_freq);
+
+	return 0;
+}
+
+static int ipu_buttress_isys_freq_get(void *data, u64 *val)
+{
+	struct ipu_device *isp = data;
+	u32 reg_val;
+	int rval;
+
+	rval = pm_runtime_get_sync(&isp->isys->dev);
+	if (rval < 0) {
+		pm_runtime_put(&isp->isys->dev);
+		dev_err(&isp->pdev->dev, "Runtime PM failed (%d)\n", rval);
+		return rval;
+	}
+
+	reg_val = readl(isp->base + BUTTRESS_REG_IS_FREQ_CTL);
+
+	pm_runtime_put(&isp->isys->dev);
+
+	*val = IPU_IS_FREQ_RATIO_BASE *
+	    (reg_val & IPU_BUTTRESS_IS_FREQ_CTL_DIVISOR_MASK);
+
+	return 0;
+}
+
+static int ipu_buttress_isys_freq_set(void *data, u64 val)
+{
+	struct ipu_device *isp = data;
+	int rval;
+
+	if (val < BUTTRESS_MIN_FORCE_IS_FREQ ||
+	    val > BUTTRESS_MAX_FORCE_IS_FREQ)
+		return -EINVAL;
+
+	rval = pm_runtime_get_sync(&isp->isys->dev);
+	if (rval < 0) {
+		pm_runtime_put(&isp->isys->dev);
+		dev_err(&isp->pdev->dev, "Runtime PM failed (%d)\n", rval);
+		return rval;
+	}
+
+	do_div(val, BUTTRESS_IS_FREQ_STEP);
+	if (val)
+		ipu_buttress_set_isys_ratio(isp, val);
+
+	pm_runtime_put(&isp->isys->dev);
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(ipu_buttress_psys_force_freq_fops,
+			ipu_buttress_psys_force_freq_get,
+			ipu_buttress_psys_force_freq_set, "%llu\n");
+
+DEFINE_SIMPLE_ATTRIBUTE(ipu_buttress_psys_freq_fops,
+			ipu_buttress_psys_freq_get, NULL, "%llu\n");
+
+DEFINE_SIMPLE_ATTRIBUTE(ipu_buttress_isys_freq_fops,
+			ipu_buttress_isys_freq_get,
+			ipu_buttress_isys_freq_set, "%llu\n");
+
+int ipu_buttress_debugfs_init(struct ipu_device *isp)
+{
+	struct debugfs_reg32 *reg =
+	    devm_kcalloc(&isp->pdev->dev, ARRAY_SIZE(buttress_regs),
+			 sizeof(*reg), GFP_KERNEL);
+	struct dentry *dir, *file;
+	int i;
+
+	if (!reg)
+		return -ENOMEM;
+
+	dir = debugfs_create_dir("buttress", isp->ipu_dir);
+	if (!dir)
+		return -ENOMEM;
+
+	for (i = 0; i < ARRAY_SIZE(buttress_regs); i++, reg++) {
+		reg->offset = (unsigned long)isp->base +
+		    buttress_regs[i].offset;
+		reg->name = buttress_regs[i].name;
+		file = debugfs_create_file(reg->name, 0700,
+					   dir, reg, &ipu_buttress_reg_fops);
+		if (!file)
+			goto err;
+	}
+
+	file = debugfs_create_file("start_tsc_sync", 0200, dir, isp,
+				   &ipu_buttress_start_tsc_sync_fops);
+	if (!file)
+		goto err;
+	file = debugfs_create_file("tsc", 0400, dir, isp,
+				   &ipu_buttress_tsc_fops);
+	if (!file)
+		goto err;
+	file = debugfs_create_file("psys_force_freq", 0700, dir, isp,
+				   &ipu_buttress_psys_force_freq_fops);
+	if (!file)
+		goto err;
+
+	file = debugfs_create_file("psys_freq", 0400, dir, isp,
+				   &ipu_buttress_psys_freq_fops);
+	if (!file)
+		goto err;
+
+	file = debugfs_create_file("isys_freq", 0700, dir, isp,
+				   &ipu_buttress_isys_freq_fops);
+	if (!file)
+		goto err;
+
+	return 0;
+err:
+	debugfs_remove_recursive(dir);
+	return -ENOMEM;
+}
+
+#endif /* CONFIG_DEBUG_FS */
+
+u64 ipu_buttress_tsc_ticks_to_ns(u64 ticks, const struct ipu_device *isp)
+{
+	u64 ns = ticks * 10000;
+
+	/*
+	 * converting TSC tick count to ns is calculated by:
+	 * Example (TSC clock frequency is 19.2MHz):
+	 * ns = ticks * 1000 000 000 / 19.2Mhz
+	 *    = ticks * 1000 000 000 / 19200000Hz
+	 *    = ticks * 10000 / 192 ns
+	 */
+	do_div(ns, isp->buttress.ref_clk);
+
+	return ns;
+}
+EXPORT_SYMBOL_GPL(ipu_buttress_tsc_ticks_to_ns);
+
+static ssize_t psys_fused_min_freq_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	struct ipu_device *isp = pci_get_drvdata(to_pci_dev(dev));
+
+	return snprintf(buf, PAGE_SIZE, "%u\n",
+			isp->buttress.psys_fused_freqs.min_freq);
+}
+
+static DEVICE_ATTR_RO(psys_fused_min_freq);
+
+static ssize_t psys_fused_max_freq_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	struct ipu_device *isp = pci_get_drvdata(to_pci_dev(dev));
+
+	return snprintf(buf, PAGE_SIZE, "%u\n",
+			isp->buttress.psys_fused_freqs.max_freq);
+}
+
+static DEVICE_ATTR_RO(psys_fused_max_freq);
+
+static ssize_t psys_fused_efficient_freq_show(struct device *dev,
+					      struct device_attribute *attr,
+					      char *buf)
+{
+	struct ipu_device *isp = pci_get_drvdata(to_pci_dev(dev));
+
+	return snprintf(buf, PAGE_SIZE, "%u\n",
+			isp->buttress.psys_fused_freqs.efficient_freq);
+}
+
+static DEVICE_ATTR_RO(psys_fused_efficient_freq);
+
+int ipu_buttress_restore(struct ipu_device *isp)
+{
+	struct ipu_buttress *b = &isp->buttress;
+
+	writel(BUTTRESS_IRQS, isp->base + BUTTRESS_REG_ISR_CLEAR);
+	writel(BUTTRESS_IRQS, isp->base + BUTTRESS_REG_ISR_ENABLE);
+	writel(b->wdt_cached_value, isp->base + BUTTRESS_REG_WDT);
+
+	return 0;
+}
+
+int ipu_buttress_init(struct ipu_device *isp)
+{
+	struct ipu_buttress *b = &isp->buttress;
+	u32 val;
+	int rval, ipc_reset_retry = BUTTRESS_CSE_IPC_RESET_RETRY;
+
+	mutex_init(&b->power_mutex);
+	mutex_init(&b->auth_mutex);
+	mutex_init(&b->cons_mutex);
+	mutex_init(&b->ipc_mutex);
+	init_completion(&b->ish.send_complete);
+	init_completion(&b->cse.send_complete);
+	init_completion(&b->ish.recv_complete);
+	init_completion(&b->cse.recv_complete);
+
+	b->cse.nack = BUTTRESS_CSE2IUDATA0_IPC_NACK;
+	b->cse.nack_mask = BUTTRESS_CSE2IUDATA0_IPC_NACK_MASK;
+	b->cse.csr_in = BUTTRESS_REG_CSE2IUCSR;
+	b->cse.csr_out = BUTTRESS_REG_IU2CSECSR;
+	b->cse.db0_in = BUTTRESS_REG_CSE2IUDB0;
+	b->cse.db0_out = BUTTRESS_REG_IU2CSEDB0;
+	b->cse.data0_in = BUTTRESS_REG_CSE2IUDATA0;
+	b->cse.data0_out = BUTTRESS_REG_IU2CSEDATA0;
+
+	/* no ISH on IPU6 */
+	memset(&b->ish, 0, sizeof(b->ish));
+	INIT_LIST_HEAD(&b->constraints);
+
+	ipu_buttress_set_secure_mode(isp);
+	isp->secure_mode = ipu_buttress_get_secure_mode(isp);
+	if (isp->secure_mode != secure_mode_enable)
+		dev_warn(&isp->pdev->dev, "Unable to set secure mode\n");
+
+	dev_info(&isp->pdev->dev, "IPU in %s mode\n",
+		 isp->secure_mode ? "secure" : "non-secure");
+
+	b->wdt_cached_value = readl(isp->base + BUTTRESS_REG_WDT);
+	writel(BUTTRESS_IRQS, isp->base + BUTTRESS_REG_ISR_CLEAR);
+	writel(BUTTRESS_IRQS, isp->base + BUTTRESS_REG_ISR_ENABLE);
+
+	/* get ref_clk frequency by reading the indication in btrs control */
+	val = readl(isp->base + BUTTRESS_REG_BTRS_CTRL);
+	val &= BUTTRESS_REG_BTRS_CTRL_REF_CLK_IND;
+	val >>= 8;
+
+	switch (val) {
+	case 0x0:
+		b->ref_clk = 240;
+		break;
+	case 0x1:
+		b->ref_clk = 192;
+		break;
+	case 0x2:
+		b->ref_clk = 384;
+		break;
+	default:
+		dev_warn(&isp->pdev->dev,
+			 "Unsupported ref clock, use 19.2Mhz by default.\n");
+		b->ref_clk = 192;
+		break;
+	}
+
+	rval = device_create_file(&isp->pdev->dev,
+				  &dev_attr_psys_fused_min_freq);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Create min freq file failed\n");
+		goto err_mutex_destroy;
+	}
+
+	rval = device_create_file(&isp->pdev->dev,
+				  &dev_attr_psys_fused_max_freq);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Create max freq file failed\n");
+		goto err_remove_min_freq_file;
+	}
+
+	rval = device_create_file(&isp->pdev->dev,
+				  &dev_attr_psys_fused_efficient_freq);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Create efficient freq file failed\n");
+		goto err_remove_max_freq_file;
+	}
+
+	/*
+	 * We want to retry couple of time in case CSE initialization
+	 * is delayed for reason or another.
+	 */
+	do {
+		rval = ipu_buttress_ipc_reset(isp, &b->cse);
+		if (rval) {
+			dev_warn(&isp->pdev->dev,
+				 "IPC reset protocol failed, retrying\n");
+		} else {
+			dev_info(&isp->pdev->dev, "IPC reset done\n");
+			return 0;
+		}
+	} while (ipc_reset_retry--);
+
+	dev_err(&isp->pdev->dev, "IPC reset protocol failed\n");
+
+err_remove_max_freq_file:
+	device_remove_file(&isp->pdev->dev, &dev_attr_psys_fused_max_freq);
+err_remove_min_freq_file:
+	device_remove_file(&isp->pdev->dev, &dev_attr_psys_fused_min_freq);
+err_mutex_destroy:
+	mutex_destroy(&b->power_mutex);
+	mutex_destroy(&b->auth_mutex);
+	mutex_destroy(&b->cons_mutex);
+	mutex_destroy(&b->ipc_mutex);
+
+	return rval;
+}
+
+void ipu_buttress_exit(struct ipu_device *isp)
+{
+	struct ipu_buttress *b = &isp->buttress;
+
+	writel(0, isp->base + BUTTRESS_REG_ISR_ENABLE);
+
+	device_remove_file(&isp->pdev->dev,
+			   &dev_attr_psys_fused_efficient_freq);
+	device_remove_file(&isp->pdev->dev, &dev_attr_psys_fused_max_freq);
+	device_remove_file(&isp->pdev->dev, &dev_attr_psys_fused_min_freq);
+
+	mutex_destroy(&b->power_mutex);
+	mutex_destroy(&b->auth_mutex);
+	mutex_destroy(&b->cons_mutex);
+	mutex_destroy(&b->ipc_mutex);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-buttress.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-buttress.h
@@ -0,0 +1,129 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_BUTTRESS_H
+#define IPU_BUTTRESS_H
+
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include "ipu.h"
+
+#define IPU_BUTTRESS_NUM_OF_SENS_CKS	3
+#define IPU_BUTTRESS_NUM_OF_PLL_CKS	3
+#define IPU_BUTTRESS_TSC_CLK		19200000
+
+#define BUTTRESS_POWER_TIMEOUT			200000
+
+#define BUTTRESS_PS_FREQ_STEP		25U
+#define BUTTRESS_MIN_FORCE_PS_FREQ	(BUTTRESS_PS_FREQ_STEP * 8)
+#define BUTTRESS_MAX_FORCE_PS_FREQ	(BUTTRESS_PS_FREQ_STEP * 32)
+
+#define BUTTRESS_IS_FREQ_STEP		25U
+#define BUTTRESS_MIN_FORCE_IS_FREQ	(BUTTRESS_IS_FREQ_STEP * 8)
+#define BUTTRESS_MAX_FORCE_IS_FREQ	(BUTTRESS_IS_FREQ_STEP * 16)
+
+struct ipu_buttress_ctrl {
+	u32 freq_ctl, pwr_sts_shift, pwr_sts_mask, pwr_sts_on, pwr_sts_off;
+	union {
+		unsigned int divisor;
+		unsigned int ratio;
+	};
+	union {
+		unsigned int divisor_shift;
+		unsigned int ratio_shift;
+	};
+	unsigned int qos_floor;
+	bool started;
+};
+
+struct ipu_buttress_fused_freqs {
+	unsigned int min_freq;
+	unsigned int max_freq;
+	unsigned int efficient_freq;
+};
+
+struct ipu_buttress_ipc {
+	struct completion send_complete;
+	struct completion recv_complete;
+	u32 nack;
+	u32 nack_mask;
+	u32 recv_data;
+	u32 csr_out;
+	u32 csr_in;
+	u32 db0_in;
+	u32 db0_out;
+	u32 data0_out;
+	u32 data0_in;
+};
+
+struct ipu_buttress {
+	struct mutex power_mutex, auth_mutex, cons_mutex, ipc_mutex;
+	struct ipu_buttress_ipc cse;
+	struct ipu_buttress_ipc ish;
+	struct list_head constraints;
+	struct ipu_buttress_fused_freqs psys_fused_freqs;
+	unsigned int psys_min_freq;
+	u32 wdt_cached_value;
+	u8 psys_force_ratio;
+	bool force_suspend;
+	u32 ref_clk;
+};
+
+struct ipu_buttress_sensor_clk_freq {
+	unsigned int rate;
+	unsigned int val;
+};
+
+struct firmware;
+
+enum ipu_buttress_ipc_domain {
+	IPU_BUTTRESS_IPC_CSE,
+	IPU_BUTTRESS_IPC_ISH,
+};
+
+struct ipu_buttress_constraint {
+	struct list_head list;
+	unsigned int min_freq;
+};
+
+struct ipu_ipc_buttress_bulk_msg {
+	u32 cmd;
+	u32 expected_resp;
+	bool require_resp;
+	u8 cmd_size;
+};
+
+int ipu_buttress_ipc_reset(struct ipu_device *isp,
+			   struct ipu_buttress_ipc *ipc);
+int ipu_buttress_map_fw_image(struct ipu_bus_device *sys,
+			      const struct firmware *fw, struct sg_table *sgt);
+int ipu_buttress_unmap_fw_image(struct ipu_bus_device *sys,
+				struct sg_table *sgt);
+int ipu_buttress_power(struct device *dev,
+		       struct ipu_buttress_ctrl *ctrl, bool on);
+void
+ipu_buttress_add_psys_constraint(struct ipu_device *isp,
+				 struct ipu_buttress_constraint *constraint);
+void
+ipu_buttress_remove_psys_constraint(struct ipu_device *isp,
+				    struct ipu_buttress_constraint *constraint);
+void ipu_buttress_set_secure_mode(struct ipu_device *isp);
+bool ipu_buttress_get_secure_mode(struct ipu_device *isp);
+int ipu_buttress_authenticate(struct ipu_device *isp);
+int ipu_buttress_reset_authentication(struct ipu_device *isp);
+bool ipu_buttress_auth_done(struct ipu_device *isp);
+int ipu_buttress_start_tsc_sync(struct ipu_device *isp);
+int ipu_buttress_tsc_read(struct ipu_device *isp, u64 *val);
+u64 ipu_buttress_tsc_ticks_to_ns(u64 ticks, const struct ipu_device *isp);
+
+irqreturn_t ipu_buttress_isr(int irq, void *isp_ptr);
+irqreturn_t ipu_buttress_isr_threaded(int irq, void *isp_ptr);
+int ipu_buttress_debugfs_init(struct ipu_device *isp);
+int ipu_buttress_init(struct ipu_device *isp);
+void ipu_buttress_exit(struct ipu_device *isp);
+void ipu_buttress_csi_port_config(struct ipu_device *isp,
+				  u32 legacy, u32 combo);
+int ipu_buttress_restore(struct ipu_device *isp);
+
+int ipu_buttress_psys_freq_get(void *data, u64 *val);
+#endif /* IPU_BUTTRESS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-cpd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-cpd.c
@@ -0,0 +1,465 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2015 - 2020 Intel Corporation
+
+#include <linux/dma-mapping.h>
+#include <linux/module.h>
+
+#include "ipu.h"
+#include "ipu-cpd.h"
+
+/* 15 entries + header*/
+#define MAX_PKG_DIR_ENT_CNT		16
+/* 2 qword per entry/header */
+#define PKG_DIR_ENT_LEN			2
+/* PKG_DIR size in bytes */
+#define PKG_DIR_SIZE			((MAX_PKG_DIR_ENT_CNT) *	\
+					 (PKG_DIR_ENT_LEN) * sizeof(u64))
+#define PKG_DIR_ID_SHIFT		48
+#define PKG_DIR_ID_MASK			0x7f
+#define PKG_DIR_VERSION_SHIFT		32
+#define PKG_DIR_SIZE_MASK		0xfffff
+/* _IUPKDR_ */
+#define PKG_DIR_HDR_MARK		0x5f4955504b44525f
+
+/* $CPD */
+#define CPD_HDR_MARK			0x44504324
+
+/* Maximum size is 2K DWORDs */
+#define MAX_MANIFEST_SIZE		(2 * 1024 * sizeof(u32))
+
+/* Maximum size is 64k */
+#define MAX_METADATA_SIZE		(64 * 1024)
+
+#define MAX_COMPONENT_ID		127
+#define MAX_COMPONENT_VERSION		0xffff
+
+#define CPD_MANIFEST_IDX	0
+#define CPD_METADATA_IDX	1
+#define CPD_MODULEDATA_IDX	2
+
+static inline struct ipu_cpd_ent *ipu_cpd_get_entries(const void *cpd)
+{
+	const struct ipu_cpd_hdr *cpd_hdr = cpd;
+
+	return (struct ipu_cpd_ent *)((u8 *)cpd + cpd_hdr->hdr_len);
+}
+
+#define ipu_cpd_get_entry(cpd, idx) (&ipu_cpd_get_entries(cpd)[idx])
+#define ipu_cpd_get_manifest(cpd) ipu_cpd_get_entry(cpd, CPD_MANIFEST_IDX)
+#define ipu_cpd_get_metadata(cpd) ipu_cpd_get_entry(cpd, CPD_METADATA_IDX)
+#define ipu_cpd_get_moduledata(cpd) ipu_cpd_get_entry(cpd, CPD_MODULEDATA_IDX)
+
+static const struct ipu_cpd_metadata_cmpnt *
+ipu_cpd_metadata_get_cmpnt(struct ipu_device *isp,
+			   const void *metadata,
+			   unsigned int metadata_size,
+			   u8 idx)
+{
+	const struct ipu_cpd_metadata_extn *extn;
+	const struct ipu_cpd_metadata_cmpnt *cmpnts;
+	int cmpnt_count;
+
+	extn = metadata;
+	cmpnts = metadata + sizeof(*extn);
+	cmpnt_count = (metadata_size - sizeof(*extn)) / sizeof(*cmpnts);
+
+	if (idx > MAX_COMPONENT_ID || idx >= cmpnt_count) {
+		dev_err(&isp->pdev->dev, "Component index out of range (%d)\n",
+			idx);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return &cmpnts[idx];
+}
+
+static u32 ipu_cpd_metadata_cmpnt_version(struct ipu_device *isp,
+					  const void *metadata,
+					  unsigned int metadata_size, u8 idx)
+{
+	const struct ipu_cpd_metadata_cmpnt *cmpnt =
+	    ipu_cpd_metadata_get_cmpnt(isp, metadata,
+				       metadata_size, idx);
+
+	if (IS_ERR(cmpnt))
+		return PTR_ERR(cmpnt);
+
+	return cmpnt->ver;
+}
+
+static int ipu_cpd_metadata_get_cmpnt_id(struct ipu_device *isp,
+					 const void *metadata,
+					 unsigned int metadata_size, u8 idx)
+{
+	const struct ipu_cpd_metadata_cmpnt *cmpnt =
+	    ipu_cpd_metadata_get_cmpnt(isp, metadata,
+				       metadata_size, idx);
+
+	if (IS_ERR(cmpnt))
+		return PTR_ERR(cmpnt);
+
+	return cmpnt->id;
+}
+
+static const struct ipu6_cpd_metadata_cmpnt *
+ipu6_cpd_metadata_get_cmpnt(struct ipu_device *isp,
+			    const void *metadata,
+			    unsigned int metadata_size,
+			    u8 idx)
+{
+	const struct ipu_cpd_metadata_extn *extn = metadata;
+	const struct ipu6_cpd_metadata_cmpnt *cmpnts = metadata + sizeof(*extn);
+	int cmpnt_count;
+
+	cmpnt_count = (metadata_size - sizeof(*extn)) / sizeof(*cmpnts);
+	if (idx > MAX_COMPONENT_ID || idx >= cmpnt_count) {
+		dev_err(&isp->pdev->dev, "Component index out of range (%d)\n",
+			idx);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return &cmpnts[idx];
+}
+
+static u32 ipu6_cpd_metadata_cmpnt_version(struct ipu_device *isp,
+					   const void *metadata,
+					   unsigned int metadata_size, u8 idx)
+{
+	const struct ipu6_cpd_metadata_cmpnt *cmpnt =
+	    ipu6_cpd_metadata_get_cmpnt(isp, metadata,
+					metadata_size, idx);
+
+	if (IS_ERR(cmpnt))
+		return PTR_ERR(cmpnt);
+
+	return cmpnt->ver;
+}
+
+static int ipu6_cpd_metadata_get_cmpnt_id(struct ipu_device *isp,
+					  const void *metadata,
+					  unsigned int metadata_size, u8 idx)
+{
+	const struct ipu6_cpd_metadata_cmpnt *cmpnt =
+	    ipu6_cpd_metadata_get_cmpnt(isp, metadata,
+					metadata_size, idx);
+
+	if (IS_ERR(cmpnt))
+		return PTR_ERR(cmpnt);
+
+	return cmpnt->id;
+}
+
+static int ipu_cpd_parse_module_data(struct ipu_device *isp,
+				     const void *module_data,
+				     unsigned int module_data_size,
+				     dma_addr_t dma_addr_module_data,
+				     u64 *pkg_dir,
+				     const void *metadata,
+				     unsigned int metadata_size)
+{
+	const struct ipu_cpd_module_data_hdr *module_data_hdr;
+	const struct ipu_cpd_hdr *dir_hdr;
+	const struct ipu_cpd_ent *dir_ent;
+	int i;
+	u8 len;
+
+	if (!module_data)
+		return -EINVAL;
+
+	module_data_hdr = module_data;
+	dir_hdr = module_data + module_data_hdr->hdr_len;
+	len = dir_hdr->hdr_len;
+	dir_ent = (struct ipu_cpd_ent *)(((u8 *)dir_hdr) + len);
+
+	pkg_dir[0] = PKG_DIR_HDR_MARK;
+	/* pkg_dir entry count = component count + pkg_dir header */
+	pkg_dir[1] = dir_hdr->ent_cnt + 1;
+
+	for (i = 0; i < dir_hdr->ent_cnt; i++, dir_ent++) {
+		u64 *p = &pkg_dir[PKG_DIR_ENT_LEN + i * PKG_DIR_ENT_LEN];
+		int ver, id;
+
+		*p++ = dma_addr_module_data + dir_ent->offset;
+
+		if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP)
+			id = ipu6_cpd_metadata_get_cmpnt_id(isp, metadata,
+							    metadata_size, i);
+		else
+			id = ipu_cpd_metadata_get_cmpnt_id(isp, metadata,
+							   metadata_size, i);
+
+		if (id < 0 || id > MAX_COMPONENT_ID) {
+			dev_err(&isp->pdev->dev,
+				"Failed to parse component id\n");
+			return -EINVAL;
+		}
+
+		if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP)
+			ver = ipu6_cpd_metadata_cmpnt_version(isp, metadata,
+							      metadata_size, i);
+		else
+			ver = ipu_cpd_metadata_cmpnt_version(isp, metadata,
+							     metadata_size, i);
+
+		if (ver < 0 || ver > MAX_COMPONENT_VERSION) {
+			dev_err(&isp->pdev->dev,
+				"Failed to parse component version\n");
+			return -EINVAL;
+		}
+
+		/*
+		 * PKG_DIR Entry (type == id)
+		 * 63:56        55      54:48   47:32   31:24   23:0
+		 * Rsvd         Rsvd    Type    Version Rsvd    Size
+		 */
+		*p = dir_ent->len | (u64)id << PKG_DIR_ID_SHIFT |
+		    (u64)ver << PKG_DIR_VERSION_SHIFT;
+	}
+
+	return 0;
+}
+
+void *ipu_cpd_create_pkg_dir(struct ipu_bus_device *adev,
+			     const void *src,
+			     dma_addr_t dma_addr_src,
+			     dma_addr_t *dma_addr, unsigned int *pkg_dir_size)
+{
+	struct ipu_device *isp = adev->isp;
+	const struct ipu_cpd_ent *ent, *man_ent, *met_ent;
+	u64 *pkg_dir;
+	unsigned int man_sz, met_sz;
+	void *pkg_dir_pos;
+	int ret;
+
+	man_ent = ipu_cpd_get_manifest(src);
+	man_sz = man_ent->len;
+
+	met_ent = ipu_cpd_get_metadata(src);
+	met_sz = met_ent->len;
+
+	*pkg_dir_size = PKG_DIR_SIZE + man_sz + met_sz;
+	pkg_dir = dma_alloc_attrs(&adev->dev, *pkg_dir_size, dma_addr,
+				  GFP_KERNEL,
+				  0);
+	if (!pkg_dir)
+		return pkg_dir;
+
+	/*
+	 * pkg_dir entry/header:
+	 * qword | 63:56 | 55   | 54:48 | 47:32 | 31:24 | 23:0
+	 * N         Address/Offset/"_IUPKDR_"
+	 * N + 1 | rsvd  | rsvd | type  | ver   | rsvd  | size
+	 *
+	 * We can ignore other fields that size in N + 1 qword as they
+	 * are 0 anyway. Just setting size for now.
+	 */
+
+	ent = ipu_cpd_get_moduledata(src);
+
+	ret = ipu_cpd_parse_module_data(isp, src + ent->offset,
+					ent->len,
+					dma_addr_src + ent->offset,
+					pkg_dir,
+					src + met_ent->offset, met_ent->len);
+	if (ret) {
+		dev_err(&isp->pdev->dev,
+			"Unable to parse module data section!\n");
+		dma_free_attrs(&isp->psys->dev, *pkg_dir_size, pkg_dir,
+			       *dma_addr,
+			       0);
+		return NULL;
+	}
+
+	/* Copy manifest after pkg_dir */
+	pkg_dir_pos = pkg_dir + PKG_DIR_ENT_LEN * MAX_PKG_DIR_ENT_CNT;
+	memcpy(pkg_dir_pos, src + man_ent->offset, man_sz);
+
+	/* Copy metadata after manifest */
+	pkg_dir_pos += man_sz;
+	memcpy(pkg_dir_pos, src + met_ent->offset, met_sz);
+
+	dma_sync_single_range_for_device(&adev->dev, *dma_addr,
+					 0, *pkg_dir_size, DMA_TO_DEVICE);
+
+	return pkg_dir;
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_create_pkg_dir);
+
+void ipu_cpd_free_pkg_dir(struct ipu_bus_device *adev,
+			  u64 *pkg_dir,
+			  dma_addr_t dma_addr, unsigned int pkg_dir_size)
+{
+	dma_free_attrs(&adev->dev, pkg_dir_size, pkg_dir, dma_addr, 0);
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_free_pkg_dir);
+
+static int ipu_cpd_validate_cpd(struct ipu_device *isp,
+				const void *cpd,
+				unsigned long cpd_size, unsigned long data_size)
+{
+	const struct ipu_cpd_hdr *cpd_hdr = cpd;
+	struct ipu_cpd_ent *ent;
+	unsigned int i;
+	u8 len;
+
+	len = cpd_hdr->hdr_len;
+
+	/* Ensure cpd hdr is within moduledata */
+	if (cpd_size < len) {
+		dev_err(&isp->pdev->dev, "Invalid CPD moduledata size\n");
+		return -EINVAL;
+	}
+
+	/* Sanity check for CPD header */
+	if ((cpd_size - len) / sizeof(*ent) < cpd_hdr->ent_cnt) {
+		dev_err(&isp->pdev->dev, "Invalid CPD header\n");
+		return -EINVAL;
+	}
+
+	/* Ensure that all entries are within moduledata */
+	ent = (struct ipu_cpd_ent *)(((u8 *)cpd_hdr) + len);
+	for (i = 0; i < cpd_hdr->ent_cnt; i++, ent++) {
+		if (data_size < ent->offset ||
+		    data_size - ent->offset < ent->len) {
+			dev_err(&isp->pdev->dev, "Invalid CPD entry (%d)\n", i);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int ipu_cpd_validate_moduledata(struct ipu_device *isp,
+				       const void *moduledata,
+				       u32 moduledata_size)
+{
+	const struct ipu_cpd_module_data_hdr *mod_hdr = moduledata;
+	int rval;
+
+	/* Ensure moduledata hdr is within moduledata */
+	if (moduledata_size < sizeof(*mod_hdr) ||
+	    moduledata_size < mod_hdr->hdr_len) {
+		dev_err(&isp->pdev->dev, "Invalid moduledata size\n");
+		return -EINVAL;
+	}
+
+	dev_info(&isp->pdev->dev, "FW version: %x\n", mod_hdr->fw_pkg_date);
+	rval = ipu_cpd_validate_cpd(isp, moduledata +
+				    mod_hdr->hdr_len,
+				    moduledata_size -
+				    mod_hdr->hdr_len, moduledata_size);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Invalid CPD in moduledata\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int ipu_cpd_validate_metadata(struct ipu_device *isp,
+				     const void *metadata, u32 meta_size)
+{
+	const struct ipu_cpd_metadata_extn *extn = metadata;
+	unsigned int size;
+
+	/* Sanity check for metadata size */
+	if (meta_size < sizeof(*extn) || meta_size > MAX_METADATA_SIZE) {
+		dev_err(&isp->pdev->dev, "%s: Invalid metadata\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Validate extension and image types */
+	if (extn->extn_type != IPU_CPD_METADATA_EXTN_TYPE_IUNIT ||
+	    extn->img_type != IPU_CPD_METADATA_IMAGE_TYPE_MAIN_FIRMWARE) {
+		dev_err(&isp->pdev->dev,
+			"Invalid metadata descriptor img_type (%d)\n",
+			extn->img_type);
+		return -EINVAL;
+	}
+
+	/* Validate metadata size multiple of metadata components */
+	if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP)
+		size = sizeof(struct ipu6_cpd_metadata_cmpnt);
+	else
+		size = sizeof(struct ipu_cpd_metadata_cmpnt);
+
+	if ((meta_size - sizeof(*extn)) % size) {
+		dev_err(&isp->pdev->dev, "%s: Invalid metadata size\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+int ipu_cpd_validate_cpd_file(struct ipu_device *isp,
+			      const void *cpd_file, unsigned long cpd_file_size)
+{
+	const struct ipu_cpd_hdr *hdr = cpd_file;
+	struct ipu_cpd_ent *ent;
+	int rval;
+
+	rval = ipu_cpd_validate_cpd(isp, cpd_file,
+				    cpd_file_size, cpd_file_size);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Invalid CPD in file\n");
+		return -EINVAL;
+	}
+
+	/* Check for CPD file marker */
+	if (hdr->hdr_mark != CPD_HDR_MARK) {
+		dev_err(&isp->pdev->dev, "Invalid CPD header\n");
+		return -EINVAL;
+	}
+
+	/* Sanity check for manifest size */
+	ent = ipu_cpd_get_manifest(cpd_file);
+	if (ent->len > MAX_MANIFEST_SIZE) {
+		dev_err(&isp->pdev->dev, "Invalid manifest size\n");
+		return -EINVAL;
+	}
+
+	/* Validate metadata */
+	ent = ipu_cpd_get_metadata(cpd_file);
+	rval = ipu_cpd_validate_metadata(isp, cpd_file + ent->offset, ent->len);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Invalid metadata\n");
+		return rval;
+	}
+
+	/* Validate moduledata */
+	ent = ipu_cpd_get_moduledata(cpd_file);
+	rval = ipu_cpd_validate_moduledata(isp, cpd_file + ent->offset,
+					   ent->len);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Invalid moduledata\n");
+		return rval;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_validate_cpd_file);
+
+unsigned int ipu_cpd_pkg_dir_get_address(const u64 *pkg_dir, int pkg_dir_idx)
+{
+	return pkg_dir[++pkg_dir_idx * PKG_DIR_ENT_LEN];
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_pkg_dir_get_address);
+
+unsigned int ipu_cpd_pkg_dir_get_num_entries(const u64 *pkg_dir)
+{
+	return pkg_dir[1];
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_pkg_dir_get_num_entries);
+
+unsigned int ipu_cpd_pkg_dir_get_size(const u64 *pkg_dir, int pkg_dir_idx)
+{
+	return pkg_dir[++pkg_dir_idx * PKG_DIR_ENT_LEN + 1] & PKG_DIR_SIZE_MASK;
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_pkg_dir_get_size);
+
+unsigned int ipu_cpd_pkg_dir_get_type(const u64 *pkg_dir, int pkg_dir_idx)
+{
+	return pkg_dir[++pkg_dir_idx * PKG_DIR_ENT_LEN + 1] >>
+	    PKG_DIR_ID_SHIFT & PKG_DIR_ID_MASK;
+}
+EXPORT_SYMBOL_GPL(ipu_cpd_pkg_dir_get_type);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-cpd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-cpd.h
@@ -0,0 +1,110 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2015 - 2020 Intel Corporation */
+
+#ifndef IPU_CPD_H
+#define IPU_CPD_H
+
+#define IPU_CPD_SIZE_OF_FW_ARCH_VERSION		7
+#define IPU_CPD_SIZE_OF_SYSTEM_VERSION		11
+#define IPU_CPD_SIZE_OF_COMPONENT_NAME		12
+
+#define IPU_CPD_METADATA_EXTN_TYPE_IUNIT	0x10
+
+#define IPU_CPD_METADATA_IMAGE_TYPE_RESERVED		0
+#define IPU_CPD_METADATA_IMAGE_TYPE_BOOTLOADER		1
+#define IPU_CPD_METADATA_IMAGE_TYPE_MAIN_FIRMWARE	2
+
+#define IPU_CPD_PKG_DIR_PSYS_SERVER_IDX	0
+#define IPU_CPD_PKG_DIR_ISYS_SERVER_IDX	1
+
+#define IPU_CPD_PKG_DIR_CLIENT_PG_TYPE	3
+
+#define IPU6_CPD_METADATA_HASH_KEY_SIZE          48
+#define IPU_CPD_METADATA_HASH_KEY_SIZE           32
+
+struct __packed ipu_cpd_module_data_hdr {
+	u32 hdr_len;
+	u32 endian;
+	u32 fw_pkg_date;
+	u32 hive_sdk_date;
+	u32 compiler_date;
+	u32 target_platform_type;
+	u8 sys_ver[IPU_CPD_SIZE_OF_SYSTEM_VERSION];
+	u8 fw_arch_ver[IPU_CPD_SIZE_OF_FW_ARCH_VERSION];
+	u8 rsvd[2];
+};
+
+/* ipu_cpd_hdr structure updated as the chksum and
+ * sub_partition_name is unused on host side
+ * CSE layout version 1.6 for ipu6se (hdr_len = 0x10)
+ * CSE layout version 1.7 for ipu6 (hdr_len = 0x14)
+ */
+struct __packed ipu_cpd_hdr {
+	u32 hdr_mark;
+	u32 ent_cnt;
+	u8 hdr_ver;
+	u8 ent_ver;
+	u8 hdr_len;
+};
+
+struct __packed ipu_cpd_ent {
+	u8 name[IPU_CPD_SIZE_OF_COMPONENT_NAME];
+	u32 offset;
+	u32 len;
+	u8 rsvd[4];
+};
+
+struct __packed ipu_cpd_metadata_cmpnt {
+	u32 id;
+	u32 size;
+	u32 ver;
+	u8 sha2_hash[IPU_CPD_METADATA_HASH_KEY_SIZE];
+	u32 entry_point;
+	u32 icache_base_offs;
+	u8 attrs[16];
+};
+
+struct __packed ipu6_cpd_metadata_cmpnt {
+	u32 id;
+	u32 size;
+	u32 ver;
+	u8 sha2_hash[IPU6_CPD_METADATA_HASH_KEY_SIZE];
+	u32 entry_point;
+	u32 icache_base_offs;
+	u8 attrs[16];
+};
+
+struct __packed ipu_cpd_metadata_extn {
+	u32 extn_type;
+	u32 len;
+	u32 img_type;
+	u8 rsvd[16];
+};
+
+struct __packed ipu_cpd_client_pkg_hdr {
+	u32 prog_list_offs;
+	u32 prog_list_size;
+	u32 prog_desc_offs;
+	u32 prog_desc_size;
+	u32 pg_manifest_offs;
+	u32 pg_manifest_size;
+	u32 prog_bin_offs;
+	u32 prog_bin_size;
+};
+
+void *ipu_cpd_create_pkg_dir(struct ipu_bus_device *adev,
+			     const void *src,
+			     dma_addr_t dma_addr_src,
+			     dma_addr_t *dma_addr, unsigned int *pkg_dir_size);
+void ipu_cpd_free_pkg_dir(struct ipu_bus_device *adev,
+			  u64 *pkg_dir,
+			  dma_addr_t dma_addr, unsigned int pkg_dir_size);
+int ipu_cpd_validate_cpd_file(struct ipu_device *isp,
+			      const void *cpd_file,
+			      unsigned long cpd_file_size);
+unsigned int ipu_cpd_pkg_dir_get_address(const u64 *pkg_dir, int pkg_dir_idx);
+unsigned int ipu_cpd_pkg_dir_get_num_entries(const u64 *pkg_dir);
+unsigned int ipu_cpd_pkg_dir_get_size(const u64 *pkg_dir, int pkg_dir_idx);
+unsigned int ipu_cpd_pkg_dir_get_type(const u64 *pkg_dir, int pkg_dir_idx);
+
+#endif /* IPU_CPD_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-dma.c
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2021 Intel Corporation
+
+#include <asm/cacheflush.h>
+
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/gfp.h>
+#include <linux/highmem.h>
+#include <linux/iova.h>
+#include <linux/module.h>
+#include <linux/scatterlist.h>
+#include <linux/version.h>
+#include <linux/vmalloc.h>
+#include <linux/dma-map-ops.h>
+
+#include "ipu-dma.h"
+#include "ipu-bus.h"
+#include "ipu-mmu.h"
+
+struct vm_info {
+	struct list_head list;
+	struct page **pages;
+	void *vaddr;
+	unsigned long size;
+};
+
+static struct vm_info *get_vm_info(struct ipu_mmu *mmu, void *vaddr)
+{
+	struct vm_info *info, *save;
+
+	list_for_each_entry_safe(info, save, &mmu->vma_list, list) {
+		if (info->vaddr == vaddr)
+			return info;
+	}
+
+	return NULL;
+}
+
+/* Begin of things adapted from arch/arm/mm/dma-mapping.c */
+static void __dma_clear_buffer(struct page *page, size_t size,
+			       unsigned long attrs)
+{
+	/*
+	 * Ensure that the allocated pages are zeroed, and that any data
+	 * lurking in the kernel direct-mapped region is invalidated.
+	 */
+	void *ptr = page_address(page);
+
+	memset(ptr, 0, size);
+	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
+		clflush_cache_range(ptr, size);
+}
+
+static struct page **__dma_alloc_buffer(struct device *dev, size_t size,
+					gfp_t gfp,
+					unsigned long attrs)
+{
+	struct page **pages;
+	int count = size >> PAGE_SHIFT;
+	int array_size = count * sizeof(struct page *);
+	int i = 0;
+
+	pages = kvzalloc(array_size, GFP_KERNEL);
+	if (!pages)
+		return NULL;
+
+	gfp |= __GFP_NOWARN;
+
+	while (count) {
+		int j, order = __fls(count);
+
+		pages[i] = alloc_pages(gfp, order);
+		while (!pages[i] && order)
+			pages[i] = alloc_pages(gfp, --order);
+		if (!pages[i])
+			goto error;
+
+		if (order) {
+			split_page(pages[i], order);
+			j = 1 << order;
+			while (--j)
+				pages[i + j] = pages[i] + j;
+		}
+
+		__dma_clear_buffer(pages[i], PAGE_SIZE << order, attrs);
+		i += 1 << order;
+		count -= 1 << order;
+	}
+
+	return pages;
+error:
+	while (i--)
+		if (pages[i])
+			__free_pages(pages[i], 0);
+	kvfree(pages);
+	return NULL;
+}
+
+static int __dma_free_buffer(struct device *dev, struct page **pages,
+			     size_t size,
+			     unsigned long attrs)
+{
+	int count = size >> PAGE_SHIFT;
+	int i;
+
+	for (i = 0; i < count; i++) {
+		if (pages[i]) {
+			__dma_clear_buffer(pages[i], PAGE_SIZE, attrs);
+			__free_pages(pages[i], 0);
+		}
+	}
+
+	kvfree(pages);
+	return 0;
+}
+
+/* End of things adapted from arch/arm/mm/dma-mapping.c */
+
+static void ipu_dma_sync_single_for_cpu(struct device *dev,
+					dma_addr_t dma_handle,
+					size_t size,
+					enum dma_data_direction dir)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	unsigned long pa = ipu_mmu_iova_to_phys(mmu->dmap->mmu_info,
+						dma_handle);
+
+	clflush_cache_range(phys_to_virt(pa), size);
+}
+
+static void ipu_dma_sync_sg_for_cpu(struct device *dev,
+				    struct scatterlist *sglist,
+				    int nents, enum dma_data_direction dir)
+{
+	struct scatterlist *sg;
+	int i;
+
+	for_each_sg(sglist, sg, nents, i)
+		clflush_cache_range(page_to_virt(sg_page(sg)), sg->length);
+}
+
+static void *ipu_dma_alloc(struct device *dev, size_t size,
+			   dma_addr_t *dma_handle, gfp_t gfp,
+			   unsigned long attrs)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	struct page **pages;
+	struct iova *iova;
+	struct vm_info *info;
+	int i;
+	int rval;
+	unsigned long count;
+
+	info = kzalloc(sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return NULL;
+
+	size = PAGE_ALIGN(size);
+	count = size >> PAGE_SHIFT;
+
+	iova = alloc_iova(&mmu->dmap->iovad, count,
+			  dma_get_mask(dev) >> PAGE_SHIFT, 0);
+	if (!iova)
+		goto out_kfree;
+
+	pages = __dma_alloc_buffer(dev, size, gfp, attrs);
+	if (!pages)
+		goto out_free_iova;
+
+	for (i = 0; iova->pfn_lo + i <= iova->pfn_hi; i++) {
+		rval = ipu_mmu_map(mmu->dmap->mmu_info,
+				   (iova->pfn_lo + i) << PAGE_SHIFT,
+				   page_to_phys(pages[i]), PAGE_SIZE);
+		if (rval)
+			goto out_unmap;
+	}
+
+	info->vaddr = vmap(pages, count, VM_USERMAP, PAGE_KERNEL);
+	if (!info->vaddr)
+		goto out_unmap;
+
+	*dma_handle = iova->pfn_lo << PAGE_SHIFT;
+
+	info->pages = pages;
+	info->size = size;
+	list_add(&info->list, &mmu->vma_list);
+
+	return info->vaddr;
+
+out_unmap:
+	for (i--; i >= 0; i--) {
+		ipu_mmu_unmap(mmu->dmap->mmu_info,
+			      (iova->pfn_lo + i) << PAGE_SHIFT, PAGE_SIZE);
+	}
+	__dma_free_buffer(dev, pages, size, attrs);
+
+out_free_iova:
+	__free_iova(&mmu->dmap->iovad, iova);
+out_kfree:
+	kfree(info);
+
+	return NULL;
+}
+
+static void ipu_dma_free(struct device *dev, size_t size, void *vaddr,
+			 dma_addr_t dma_handle,
+			 unsigned long attrs)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	struct page **pages;
+	struct vm_info *info;
+	struct iova *iova = find_iova(&mmu->dmap->iovad,
+				      dma_handle >> PAGE_SHIFT);
+
+	if (WARN_ON(!iova))
+		return;
+
+	info = get_vm_info(mmu, vaddr);
+	if (WARN_ON(!info))
+		return;
+
+	if (WARN_ON(!info->vaddr))
+		return;
+
+	if (WARN_ON(!info->pages))
+		return;
+
+	list_del(&info->list);
+
+	size = PAGE_ALIGN(size);
+
+	pages = info->pages;
+
+	vunmap(vaddr);
+
+	ipu_mmu_unmap(mmu->dmap->mmu_info, iova->pfn_lo << PAGE_SHIFT,
+		      (iova->pfn_hi - iova->pfn_lo + 1) << PAGE_SHIFT);
+
+	__dma_free_buffer(dev, pages, size, attrs);
+
+	mmu->tlb_invalidate(mmu);
+
+	__free_iova(&mmu->dmap->iovad, iova);
+
+	kfree(info);
+}
+
+static int ipu_dma_mmap(struct device *dev, struct vm_area_struct *vma,
+			void *addr, dma_addr_t iova, size_t size,
+			unsigned long attrs)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	struct vm_info *info;
+	size_t count = PAGE_ALIGN(size) >> PAGE_SHIFT;
+	size_t i;
+
+	info = get_vm_info(mmu, addr);
+	if (!info)
+		return -EFAULT;
+
+	if (!info->vaddr)
+		return -EFAULT;
+
+	if (vma->vm_start & ~PAGE_MASK)
+		return -EINVAL;
+
+	if (size > info->size)
+		return -EFAULT;
+
+	for (i = 0; i < count; i++)
+		vm_insert_page(vma, vma->vm_start + (i << PAGE_SHIFT),
+			       info->pages[i]);
+
+	return 0;
+}
+
+static void ipu_dma_unmap_sg(struct device *dev,
+			     struct scatterlist *sglist,
+			     int nents, enum dma_data_direction dir,
+			     unsigned long attrs)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	struct iova *iova = find_iova(&mmu->dmap->iovad,
+				      sg_dma_address(sglist) >> PAGE_SHIFT);
+
+	if (!nents)
+		return;
+
+	if (WARN_ON(!iova))
+		return;
+
+	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
+		ipu_dma_sync_sg_for_cpu(dev, sglist, nents, DMA_BIDIRECTIONAL);
+
+	ipu_mmu_unmap(mmu->dmap->mmu_info, iova->pfn_lo << PAGE_SHIFT,
+		      (iova->pfn_hi - iova->pfn_lo + 1) << PAGE_SHIFT);
+
+	mmu->tlb_invalidate(mmu);
+
+	__free_iova(&mmu->dmap->iovad, iova);
+}
+
+static int ipu_dma_map_sg(struct device *dev, struct scatterlist *sglist,
+			  int nents, enum dma_data_direction dir,
+			  unsigned long attrs)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	struct scatterlist *sg;
+	struct iova *iova;
+	size_t size = 0;
+	u32 iova_addr;
+	int i;
+
+	for_each_sg(sglist, sg, nents, i)
+		size += PAGE_ALIGN(sg->length) >> PAGE_SHIFT;
+
+	dev_dbg(dev, "dmamap: mapping sg %d entries, %zu pages\n", nents, size);
+
+	iova = alloc_iova(&mmu->dmap->iovad, size,
+			  dma_get_mask(dev) >> PAGE_SHIFT, 0);
+	if (!iova)
+		return 0;
+
+	dev_dbg(dev, "dmamap: iova low pfn %lu, high pfn %lu\n", iova->pfn_lo,
+		iova->pfn_hi);
+
+	iova_addr = iova->pfn_lo;
+
+	for_each_sg(sglist, sg, nents, i) {
+		int rval;
+
+		dev_dbg(dev, "mapping entry %d: iova 0x%8.8x,phy 0x%16.16llx\n",
+			i, iova_addr << PAGE_SHIFT,
+			(unsigned long long)page_to_phys(sg_page(sg)));
+		rval = ipu_mmu_map(mmu->dmap->mmu_info, iova_addr << PAGE_SHIFT,
+				   page_to_phys(sg_page(sg)),
+				   PAGE_ALIGN(sg->length));
+		if (rval)
+			goto out_fail;
+		sg_dma_address(sg) = iova_addr << PAGE_SHIFT;
+#ifdef CONFIG_NEED_SG_DMA_LENGTH
+		sg_dma_len(sg) = sg->length;
+#endif /* CONFIG_NEED_SG_DMA_LENGTH */
+
+		iova_addr += PAGE_ALIGN(sg->length) >> PAGE_SHIFT;
+	}
+
+	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
+		ipu_dma_sync_sg_for_cpu(dev, sglist, nents, DMA_BIDIRECTIONAL);
+
+	mmu->tlb_invalidate(mmu);
+
+	return nents;
+
+out_fail:
+	ipu_dma_unmap_sg(dev, sglist, i, dir, attrs);
+
+	return 0;
+}
+
+/*
+ * Create scatter-list for the already allocated DMA buffer
+ */
+static int ipu_dma_get_sgtable(struct device *dev, struct sg_table *sgt,
+			       void *cpu_addr, dma_addr_t handle, size_t size,
+			       unsigned long attrs)
+{
+	struct ipu_mmu *mmu = to_ipu_bus_device(dev)->mmu;
+	struct vm_info *info;
+	int n_pages;
+	int ret = 0;
+
+	info = get_vm_info(mmu, cpu_addr);
+	if (!info)
+		return -EFAULT;
+
+	if (!info->vaddr)
+		return -EFAULT;
+
+	if (WARN_ON(!info->pages))
+		return -ENOMEM;
+
+	n_pages = PAGE_ALIGN(size) >> PAGE_SHIFT;
+
+	ret = sg_alloc_table_from_pages(sgt, info->pages, n_pages, 0, size,
+					GFP_KERNEL);
+	if (ret)
+		dev_dbg(dev, "IPU get sgt table fail\n");
+
+	return ret;
+}
+
+const struct dma_map_ops ipu_dma_ops = {
+	.alloc = ipu_dma_alloc,
+	.free = ipu_dma_free,
+	.mmap = ipu_dma_mmap,
+	.map_sg = ipu_dma_map_sg,
+	.unmap_sg = ipu_dma_unmap_sg,
+	.sync_single_for_cpu = ipu_dma_sync_single_for_cpu,
+	.sync_single_for_device = ipu_dma_sync_single_for_cpu,
+	.sync_sg_for_cpu = ipu_dma_sync_sg_for_cpu,
+	.sync_sg_for_device = ipu_dma_sync_sg_for_cpu,
+	.get_sgtable = ipu_dma_get_sgtable,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-dma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-dma.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_DMA_H
+#define IPU_DMA_H
+
+#include <linux/iova.h>
+
+struct ipu_mmu_info;
+
+struct ipu_dma_mapping {
+	struct ipu_mmu_info *mmu_info;
+	struct iova_domain iovad;
+	struct kref ref;
+};
+
+extern const struct dma_map_ops ipu_dma_ops;
+
+#endif /* IPU_DMA_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-fw-com.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-fw-com.c
@@ -0,0 +1,496 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <asm/cacheflush.h>
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/dma-mapping.h>
+
+#include "ipu.h"
+#include "ipu-fw-com.h"
+#include "ipu-bus.h"
+
+/*
+ * FWCOM layer is a shared resource between FW and driver. It consist
+ * of token queues to both send and receive directions. Queue is simply
+ * an array of structures with read and write indexes to the queue.
+ * There are 1...n queues to both directions. Queues locates in
+ * system ram and are mapped to ISP MMU so that both CPU and ISP can
+ * see the same buffer. Indexes are located in ISP DMEM so that FW code
+ * can poll those with very low latency and cost. CPU access to indexes is
+ * more costly but that happens only at message sending time and
+ * interrupt trigged message handling. CPU doesn't need to poll indexes.
+ * wr_reg / rd_reg are offsets to those dmem location. They are not
+ * the indexes itself.
+ */
+
+/* Shared structure between driver and FW - do not modify */
+struct ipu_fw_sys_queue {
+	u64 host_address;
+	u32 vied_address;
+	u32 size;
+	u32 token_size;
+	u32 wr_reg;	/* reg no in subsystem's regmem */
+	u32 rd_reg;
+	u32 _align;
+};
+
+struct ipu_fw_sys_queue_res {
+	u64 host_address;
+	u32 vied_address;
+	u32 reg;
+};
+
+enum syscom_state {
+	/* Program load or explicit host setting should init to this */
+	SYSCOM_STATE_UNINIT = 0x57A7E000,
+	/* SP Syscom sets this when it is ready for use */
+	SYSCOM_STATE_READY = 0x57A7E001,
+	/* SP Syscom sets this when no more syscom accesses will happen */
+	SYSCOM_STATE_INACTIVE = 0x57A7E002
+};
+
+enum syscom_cmd {
+	/* Program load or explicit host setting should init to this */
+	SYSCOM_COMMAND_UNINIT = 0x57A7F000,
+	/* Host Syscom requests syscom to become inactive */
+	SYSCOM_COMMAND_INACTIVE = 0x57A7F001
+};
+
+/* firmware config: data that sent from the host to SP via DDR */
+/* Cell copies data into a context */
+
+struct ipu_fw_syscom_config {
+	u32 firmware_address;
+
+	u32 num_input_queues;
+	u32 num_output_queues;
+
+	/* ISP pointers to an array of ipu_fw_sys_queue structures */
+	u32 input_queue;
+	u32 output_queue;
+
+	/* ISYS / PSYS private data */
+	u32 specific_addr;
+	u32 specific_size;
+};
+
+/* End of shared structures / data */
+
+struct ipu_fw_com_context {
+	struct ipu_bus_device *adev;
+	void __iomem *dmem_addr;
+	int (*cell_ready)(struct ipu_bus_device *adev);
+	void (*cell_start)(struct ipu_bus_device *adev);
+
+	void *dma_buffer;
+	dma_addr_t dma_addr;
+	unsigned int dma_size;
+	unsigned long attrs;
+
+	unsigned int num_input_queues;
+	unsigned int num_output_queues;
+
+	struct ipu_fw_sys_queue *input_queue;	/* array of host to SP queues */
+	struct ipu_fw_sys_queue *output_queue;	/* array of SP to host */
+
+	void *config_host_addr;
+	void *specific_host_addr;
+	u64 ibuf_host_addr;
+	u64 obuf_host_addr;
+
+	u32 config_vied_addr;
+	u32 input_queue_vied_addr;
+	u32 output_queue_vied_addr;
+	u32 specific_vied_addr;
+	u32 ibuf_vied_addr;
+	u32 obuf_vied_addr;
+
+	unsigned int buttress_boot_offset;
+	void __iomem *base_addr;
+};
+
+#define FW_COM_WR_REG 0
+#define FW_COM_RD_REG 4
+
+#define REGMEM_OFFSET 0
+#define TUNIT_MAGIC_PATTERN 0x5a5a5a5a
+
+enum regmem_id {
+	/* pass pkg_dir address to SPC in non-secure mode */
+	PKG_DIR_ADDR_REG = 0,
+	/* Tunit CFG blob for secure - provided by host.*/
+	TUNIT_CFG_DWR_REG = 1,
+	/* syscom commands - modified by the host */
+	SYSCOM_COMMAND_REG = 2,
+	/* Store interrupt status - updated by SP */
+	SYSCOM_IRQ_REG = 3,
+	/* first syscom queue pointer register */
+	SYSCOM_QPR_BASE_REG = 4
+};
+
+enum message_direction {
+	DIR_RECV = 0,
+	DIR_SEND
+};
+
+#define BUTRESS_FW_BOOT_PARAMS_0 0x4000
+#define BUTTRESS_FW_BOOT_PARAM_REG(base, offset, id) ((base) \
+	+ BUTRESS_FW_BOOT_PARAMS_0 + ((offset) + (id)) * 4)
+
+enum buttress_syscom_id {
+	/* pass syscom configuration to SPC */
+	SYSCOM_CONFIG_ID		= 0,
+	/* syscom state - modified by SP */
+	SYSCOM_STATE_ID			= 1,
+	/* syscom vtl0 addr mask */
+	SYSCOM_VTL0_ADDR_MASK_ID	= 2,
+	SYSCOM_ID_MAX
+};
+
+static unsigned int num_messages(unsigned int wr, unsigned int rd,
+				 unsigned int size)
+{
+	if (wr < rd)
+		wr += size;
+	return wr - rd;
+}
+
+static unsigned int num_free(unsigned int wr, unsigned int rd,
+			     unsigned int size)
+{
+	return size - num_messages(wr, rd, size);
+}
+
+static unsigned int curr_index(void __iomem *q_dmem,
+			       enum message_direction dir)
+{
+	return readl(q_dmem +
+			 (dir == DIR_RECV ? FW_COM_RD_REG : FW_COM_WR_REG));
+}
+
+static unsigned int inc_index(void __iomem *q_dmem, struct ipu_fw_sys_queue *q,
+			      enum message_direction dir)
+{
+	unsigned int index;
+
+	index = curr_index(q_dmem, dir) + 1;
+	return index >= q->size ? 0 : index;
+}
+
+static unsigned int ipu_sys_queue_buf_size(unsigned int size,
+					   unsigned int token_size)
+{
+	return (size + 1) * token_size;
+}
+
+static void ipu_sys_queue_init(struct ipu_fw_sys_queue *q, unsigned int size,
+			       unsigned int token_size,
+			       struct ipu_fw_sys_queue_res *res)
+{
+	unsigned int buf_size;
+
+	q->size = size + 1;
+	q->token_size = token_size;
+	buf_size = ipu_sys_queue_buf_size(size, token_size);
+
+	/* acquire the shared buffer space */
+	q->host_address = res->host_address;
+	res->host_address += buf_size;
+	q->vied_address = res->vied_address;
+	res->vied_address += buf_size;
+
+	/* acquire the shared read and writer pointers */
+	q->wr_reg = res->reg;
+	res->reg++;
+	q->rd_reg = res->reg;
+	res->reg++;
+}
+
+void *ipu_fw_com_prepare(struct ipu_fw_com_cfg *cfg,
+			 struct ipu_bus_device *adev, void __iomem *base)
+{
+	struct ipu_fw_com_context *ctx;
+	struct ipu_fw_syscom_config *fw_cfg;
+	unsigned int i;
+	unsigned int sizeall, offset;
+	unsigned int sizeinput = 0, sizeoutput = 0;
+	unsigned long attrs = 0;
+	struct ipu_fw_sys_queue_res res;
+
+	/* error handling */
+	if (!cfg || !cfg->cell_start || !cfg->cell_ready)
+		return NULL;
+
+	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return NULL;
+	ctx->dmem_addr = base + cfg->dmem_addr + REGMEM_OFFSET;
+	ctx->adev = adev;
+	ctx->cell_start = cfg->cell_start;
+	ctx->cell_ready = cfg->cell_ready;
+	ctx->buttress_boot_offset = cfg->buttress_boot_offset;
+	ctx->base_addr  = base;
+
+	ctx->num_input_queues = cfg->num_input_queues;
+	ctx->num_output_queues = cfg->num_output_queues;
+
+	/*
+	 * Allocate DMA mapped memory. Allocate one big chunk.
+	 */
+	sizeall =
+	    /* Base cfg for FW */
+	    roundup(sizeof(struct ipu_fw_syscom_config), 8) +
+	    /* Descriptions of the queues */
+	    cfg->num_input_queues * sizeof(struct ipu_fw_sys_queue) +
+	    cfg->num_output_queues * sizeof(struct ipu_fw_sys_queue) +
+	    /* FW specific information structure */
+	    roundup(cfg->specific_size, 8);
+
+	for (i = 0; i < cfg->num_input_queues; i++)
+		sizeinput += ipu_sys_queue_buf_size(cfg->input[i].queue_size,
+						cfg->input[i].token_size);
+
+	for (i = 0; i < cfg->num_output_queues; i++)
+		sizeoutput += ipu_sys_queue_buf_size(cfg->output[i].queue_size,
+						 cfg->output[i].token_size);
+
+	sizeall += sizeinput + sizeoutput;
+
+	ctx->dma_buffer = dma_alloc_attrs(&ctx->adev->dev, sizeall,
+					  &ctx->dma_addr, GFP_KERNEL,
+					  attrs);
+	ctx->attrs = attrs;
+	if (!ctx->dma_buffer) {
+		dev_err(&ctx->adev->dev, "failed to allocate dma memory\n");
+		kfree(ctx);
+		return NULL;
+	}
+
+	ctx->dma_size = sizeall;
+
+	/* This is the address where FW starts to parse allocations */
+	ctx->config_host_addr = ctx->dma_buffer;
+	ctx->config_vied_addr = ctx->dma_addr;
+	fw_cfg = (struct ipu_fw_syscom_config *)ctx->config_host_addr;
+	offset = roundup(sizeof(struct ipu_fw_syscom_config), 8);
+
+	ctx->input_queue = ctx->dma_buffer + offset;
+	ctx->input_queue_vied_addr = ctx->dma_addr + offset;
+	offset += cfg->num_input_queues * sizeof(struct ipu_fw_sys_queue);
+
+	ctx->output_queue = ctx->dma_buffer + offset;
+	ctx->output_queue_vied_addr = ctx->dma_addr + offset;
+	offset += cfg->num_output_queues * sizeof(struct ipu_fw_sys_queue);
+
+	ctx->specific_host_addr = ctx->dma_buffer + offset;
+	ctx->specific_vied_addr = ctx->dma_addr + offset;
+	offset += roundup(cfg->specific_size, 8);
+
+	ctx->ibuf_host_addr = (uintptr_t)(ctx->dma_buffer + offset);
+	ctx->ibuf_vied_addr = ctx->dma_addr + offset;
+	offset += sizeinput;
+
+	ctx->obuf_host_addr = (uintptr_t)(ctx->dma_buffer + offset);
+	ctx->obuf_vied_addr = ctx->dma_addr + offset;
+	offset += sizeoutput;
+
+	/* initialize input queues */
+	res.reg = SYSCOM_QPR_BASE_REG;
+	res.host_address = ctx->ibuf_host_addr;
+	res.vied_address = ctx->ibuf_vied_addr;
+	for (i = 0; i < cfg->num_input_queues; i++) {
+		ipu_sys_queue_init(ctx->input_queue + i,
+				   cfg->input[i].queue_size,
+				   cfg->input[i].token_size, &res);
+	}
+
+	/* initialize output queues */
+	res.host_address = ctx->obuf_host_addr;
+	res.vied_address = ctx->obuf_vied_addr;
+	for (i = 0; i < cfg->num_output_queues; i++) {
+		ipu_sys_queue_init(ctx->output_queue + i,
+				   cfg->output[i].queue_size,
+				   cfg->output[i].token_size, &res);
+	}
+
+	/* copy firmware specific data */
+	if (cfg->specific_addr && cfg->specific_size) {
+		memcpy((void *)ctx->specific_host_addr,
+		       cfg->specific_addr, cfg->specific_size);
+	}
+
+	fw_cfg->num_input_queues = cfg->num_input_queues;
+	fw_cfg->num_output_queues = cfg->num_output_queues;
+	fw_cfg->input_queue = ctx->input_queue_vied_addr;
+	fw_cfg->output_queue = ctx->output_queue_vied_addr;
+	fw_cfg->specific_addr = ctx->specific_vied_addr;
+	fw_cfg->specific_size = cfg->specific_size;
+	return ctx;
+}
+EXPORT_SYMBOL_GPL(ipu_fw_com_prepare);
+
+int ipu_fw_com_open(struct ipu_fw_com_context *ctx)
+{
+	/*
+	 * Disable tunit configuration by FW.
+	 * This feature is used to configure tunit in secure mode.
+	 */
+	writel(TUNIT_MAGIC_PATTERN, ctx->dmem_addr + TUNIT_CFG_DWR_REG * 4);
+	/* Check if SP is in valid state */
+	if (!ctx->cell_ready(ctx->adev))
+		return -EIO;
+
+	/* store syscom uninitialized command */
+	writel(SYSCOM_COMMAND_UNINIT,
+	       ctx->dmem_addr + SYSCOM_COMMAND_REG * 4);
+
+	/* store syscom uninitialized state */
+	writel(SYSCOM_STATE_UNINIT,
+	       BUTTRESS_FW_BOOT_PARAM_REG(ctx->base_addr,
+					  ctx->buttress_boot_offset,
+					  SYSCOM_STATE_ID));
+
+	/* store firmware configuration address */
+	writel(ctx->config_vied_addr,
+	       BUTTRESS_FW_BOOT_PARAM_REG(ctx->base_addr,
+					  ctx->buttress_boot_offset,
+					  SYSCOM_CONFIG_ID));
+	ctx->cell_start(ctx->adev);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_fw_com_open);
+
+int ipu_fw_com_close(struct ipu_fw_com_context *ctx)
+{
+	int state;
+
+	state = readl(BUTTRESS_FW_BOOT_PARAM_REG(ctx->base_addr,
+						 ctx->buttress_boot_offset,
+						 SYSCOM_STATE_ID));
+	if (state != SYSCOM_STATE_READY)
+		return -EBUSY;
+
+	/* set close request flag */
+	writel(SYSCOM_COMMAND_INACTIVE, ctx->dmem_addr +
+		   SYSCOM_COMMAND_REG * 4);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_fw_com_close);
+
+int ipu_fw_com_release(struct ipu_fw_com_context *ctx, unsigned int force)
+{
+	/* check if release is forced, an verify cell state if it is not */
+	if (!force && !ctx->cell_ready(ctx->adev))
+		return -EBUSY;
+
+	dma_free_attrs(&ctx->adev->dev, ctx->dma_size,
+		       ctx->dma_buffer, ctx->dma_addr,
+		       ctx->attrs);
+	kfree(ctx);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_fw_com_release);
+
+int ipu_fw_com_ready(struct ipu_fw_com_context *ctx)
+{
+	int state;
+
+	state = readl(BUTTRESS_FW_BOOT_PARAM_REG(ctx->base_addr,
+						 ctx->buttress_boot_offset,
+						 SYSCOM_STATE_ID));
+	if (state != SYSCOM_STATE_READY)
+		return -EBUSY;	/* SPC is not ready to handle messages yet */
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ipu_fw_com_ready);
+
+static bool is_index_valid(struct ipu_fw_sys_queue *q, unsigned int index)
+{
+	if (index >= q->size)
+		return false;
+	return true;
+}
+
+void *ipu_send_get_token(struct ipu_fw_com_context *ctx, int q_nbr)
+{
+	struct ipu_fw_sys_queue *q = &ctx->input_queue[q_nbr];
+	void __iomem *q_dmem = ctx->dmem_addr + q->wr_reg * 4;
+	unsigned int wr, rd;
+	unsigned int packets;
+	unsigned int index;
+
+	wr = readl(q_dmem + FW_COM_WR_REG);
+	rd = readl(q_dmem + FW_COM_RD_REG);
+
+	/* Catch indexes in dmem */
+	if (!is_index_valid(q, wr) || !is_index_valid(q, rd))
+		return NULL;
+
+	packets = num_free(wr + 1, rd, q->size);
+	if (!packets)
+		return NULL;
+
+	index = curr_index(q_dmem, DIR_SEND);
+
+	return (void *)(unsigned long)q->host_address + (index * q->token_size);
+}
+EXPORT_SYMBOL_GPL(ipu_send_get_token);
+
+void ipu_send_put_token(struct ipu_fw_com_context *ctx, int q_nbr)
+{
+	struct ipu_fw_sys_queue *q = &ctx->input_queue[q_nbr];
+	void __iomem *q_dmem = ctx->dmem_addr + q->wr_reg * 4;
+	int index = curr_index(q_dmem, DIR_SEND);
+
+	/* Increment index */
+	index = inc_index(q_dmem, q, DIR_SEND);
+
+	writel(index, q_dmem + FW_COM_WR_REG);
+}
+EXPORT_SYMBOL_GPL(ipu_send_put_token);
+
+void *ipu_recv_get_token(struct ipu_fw_com_context *ctx, int q_nbr)
+{
+	struct ipu_fw_sys_queue *q = &ctx->output_queue[q_nbr];
+	void __iomem *q_dmem = ctx->dmem_addr + q->wr_reg * 4;
+	unsigned int wr, rd;
+	unsigned int packets;
+	void *addr;
+
+	wr = readl(q_dmem + FW_COM_WR_REG);
+	rd = readl(q_dmem + FW_COM_RD_REG);
+
+	/* Catch indexes in dmem? */
+	if (!is_index_valid(q, wr) || !is_index_valid(q, rd))
+		return NULL;
+
+	packets = num_messages(wr, rd, q->size);
+	if (!packets)
+		return NULL;
+
+	addr = (void *)(unsigned long)q->host_address + (rd * q->token_size);
+
+	return addr;
+}
+EXPORT_SYMBOL_GPL(ipu_recv_get_token);
+
+void ipu_recv_put_token(struct ipu_fw_com_context *ctx, int q_nbr)
+{
+	struct ipu_fw_sys_queue *q = &ctx->output_queue[q_nbr];
+	void __iomem *q_dmem = ctx->dmem_addr + q->wr_reg * 4;
+	unsigned int rd = inc_index(q_dmem, q, DIR_RECV);
+
+	/* Release index */
+	writel(rd, q_dmem + FW_COM_RD_REG);
+}
+EXPORT_SYMBOL_GPL(ipu_recv_put_token);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel ipu fw comm library");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-fw-com.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-fw-com.h
@@ -0,0 +1,48 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_FW_COM_H
+#define IPU_FW_COM_H
+
+struct ipu_fw_com_context;
+struct ipu_bus_device;
+
+struct ipu_fw_syscom_queue_config {
+	unsigned int queue_size;	/* tokens per queue */
+	unsigned int token_size;	/* bytes per token */
+};
+
+#define SYSCOM_BUTTRESS_FW_PARAMS_ISYS_OFFSET	0
+#define SYSCOM_BUTTRESS_FW_PARAMS_PSYS_OFFSET	7
+
+struct ipu_fw_com_cfg {
+	unsigned int num_input_queues;
+	unsigned int num_output_queues;
+	struct ipu_fw_syscom_queue_config *input;
+	struct ipu_fw_syscom_queue_config *output;
+
+	unsigned int dmem_addr;
+
+	/* firmware-specific configuration data */
+	void *specific_addr;
+	unsigned int specific_size;
+	int (*cell_ready)(struct ipu_bus_device *adev);
+	void (*cell_start)(struct ipu_bus_device *adev);
+
+	unsigned int buttress_boot_offset;
+};
+
+void *ipu_fw_com_prepare(struct ipu_fw_com_cfg *cfg,
+			 struct ipu_bus_device *adev, void __iomem *base);
+
+int ipu_fw_com_open(struct ipu_fw_com_context *ctx);
+int ipu_fw_com_ready(struct ipu_fw_com_context *ctx);
+int ipu_fw_com_close(struct ipu_fw_com_context *ctx);
+int ipu_fw_com_release(struct ipu_fw_com_context *ctx, unsigned int force);
+
+void *ipu_recv_get_token(struct ipu_fw_com_context *ctx, int q_nbr);
+void ipu_recv_put_token(struct ipu_fw_com_context *ctx, int q_nbr);
+void *ipu_send_get_token(struct ipu_fw_com_context *ctx, int q_nbr);
+void ipu_send_put_token(struct ipu_fw_com_context *ctx, int q_nbr);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-fw-isys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-fw-isys.c
@@ -0,0 +1,600 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2021 Intel Corporation
+
+#include <asm/cacheflush.h>
+
+#include <linux/kernel.h>
+#include <linux/delay.h>
+
+#include "ipu.h"
+#include "ipu-trace.h"
+#include "ipu-platform-regs.h"
+#include "ipu-platform.h"
+#include "ipu-fw-isys.h"
+#include "ipu-fw-com.h"
+#include "ipu-isys.h"
+
+#define IPU_FW_UNSUPPORTED_DATA_TYPE	0
+static const uint32_t
+extracted_bits_per_pixel_per_mipi_data_type[N_IPU_FW_ISYS_MIPI_DATA_TYPE] = {
+	64,	/* [0x00]   IPU_FW_ISYS_MIPI_DATA_TYPE_FRAME_START_CODE */
+	64,	/* [0x01]   IPU_FW_ISYS_MIPI_DATA_TYPE_FRAME_END_CODE */
+	64,	/* [0x02]   IPU_FW_ISYS_MIPI_DATA_TYPE_LINE_START_CODE */
+	64,	/* [0x03]   IPU_FW_ISYS_MIPI_DATA_TYPE_LINE_END_CODE */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x04] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x05] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x06] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x07] */
+	64,	/* [0x08]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT1 */
+	64,	/* [0x09]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT2 */
+	64,	/* [0x0A]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT3 */
+	64,	/* [0x0B]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT4 */
+	64,	/* [0x0C]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT5 */
+	64,	/* [0x0D]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT6 */
+	64,	/* [0x0E]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT7 */
+	64,	/* [0x0F]   IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT8 */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x10] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x11] */
+	8,	/* [0x12]    IPU_FW_ISYS_MIPI_DATA_TYPE_EMBEDDED */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x13] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x14] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x15] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x16] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x17] */
+	12,	/* [0x18]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_8 */
+	15,	/* [0x19]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_10 */
+	12,	/* [0x1A]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_8_LEGACY */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x1B] */
+	12,	/* [0x1C]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_8_SHIFT */
+	15,	/* [0x1D]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_10_SHIFT */
+	16,	/* [0x1E]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV422_8 */
+	20,	/* [0x1F]   IPU_FW_ISYS_MIPI_DATA_TYPE_YUV422_10 */
+	16,	/* [0x20]   IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_444 */
+	16,	/* [0x21]   IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_555 */
+	16,	/* [0x22]   IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_565 */
+	18,	/* [0x23]   IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_666 */
+	24,	/* [0x24]   IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_888 */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x25] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x26] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x27] */
+	6,	/* [0x28]    IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_6 */
+	7,	/* [0x29]    IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_7 */
+	8,	/* [0x2A]    IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_8 */
+	10,	/* [0x2B]   IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_10 */
+	12,	/* [0x2C]   IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_12 */
+	14,	/* [0x2D]   IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_14 */
+	16,	/* [0x2E]   IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_16 */
+	8,	/* [0x2F]    IPU_FW_ISYS_MIPI_DATA_TYPE_BINARY_8 */
+	8,	/* [0x30]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF1 */
+	8,	/* [0x31]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF2 */
+	8,	/* [0x32]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF3 */
+	8,	/* [0x33]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF4 */
+	8,	/* [0x34]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF5 */
+	8,	/* [0x35]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF6 */
+	8,	/* [0x36]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF7 */
+	8,	/* [0x37]    IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF8 */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x38] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x39] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x3A] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x3B] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x3C] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x3D] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE,	/* [0x3E] */
+	IPU_FW_UNSUPPORTED_DATA_TYPE	/* [0x3F] */
+};
+
+static const char send_msg_types[N_IPU_FW_ISYS_SEND_TYPE][32] = {
+	"STREAM_OPEN",
+	"STREAM_START",
+	"STREAM_START_AND_CAPTURE",
+	"STREAM_CAPTURE",
+	"STREAM_STOP",
+	"STREAM_FLUSH",
+	"STREAM_CLOSE"
+};
+
+static int handle_proxy_response(struct ipu_isys *isys, unsigned int req_id)
+{
+	struct ipu_fw_isys_proxy_resp_info_abi *resp;
+	int rval = -EIO;
+
+	resp = (struct ipu_fw_isys_proxy_resp_info_abi *)
+	    ipu_recv_get_token(isys->fwcom, IPU_BASE_PROXY_RECV_QUEUES);
+	if (!resp)
+		return 1;
+
+	dev_dbg(&isys->adev->dev,
+		"Proxy response: id 0x%x, error %d, details %d\n",
+		resp->request_id, resp->error_info.error,
+		resp->error_info.error_details);
+
+	if (req_id == resp->request_id)
+		rval = 0;
+
+	ipu_recv_put_token(isys->fwcom, IPU_BASE_PROXY_RECV_QUEUES);
+	return rval;
+}
+
+/* Simple blocking proxy send function */
+int ipu_fw_isys_send_proxy_token(struct ipu_isys *isys,
+				 unsigned int req_id,
+				 unsigned int index,
+				 unsigned int offset, u32 value)
+{
+	struct ipu_fw_com_context *ctx = isys->fwcom;
+	struct ipu_fw_proxy_send_queue_token *token;
+	unsigned int timeout = 1000;
+	int rval = -EBUSY;
+
+	dev_dbg(&isys->adev->dev,
+		"proxy send token: req_id 0x%x, index %d, offset 0x%x, value 0x%x\n",
+		req_id, index, offset, value);
+
+	token = ipu_send_get_token(ctx, IPU_BASE_PROXY_SEND_QUEUES);
+	if (!token)
+		goto leave;
+
+	token->request_id = req_id;
+	token->region_index = index;
+	token->offset = offset;
+	token->value = value;
+	ipu_send_put_token(ctx, IPU_BASE_PROXY_SEND_QUEUES);
+
+	/* Currently proxy doesn't support irq based service. Poll */
+	do {
+		usleep_range(100, 110);
+		rval = handle_proxy_response(isys, req_id);
+		if (!rval)
+			break;
+		if (rval == -EIO) {
+			dev_err(&isys->adev->dev,
+				"Proxy response received with unexpected id\n");
+			break;
+		}
+		timeout--;
+	} while (rval && timeout);
+
+	if (!timeout)
+		dev_err(&isys->adev->dev, "Proxy response timed out\n");
+leave:
+	return rval;
+}
+
+int
+ipu_fw_isys_complex_cmd(struct ipu_isys *isys,
+			const unsigned int stream_handle,
+			void *cpu_mapped_buf,
+			dma_addr_t dma_mapped_buf,
+			size_t size, enum ipu_fw_isys_send_type send_type)
+{
+	struct ipu_fw_com_context *ctx = isys->fwcom;
+	struct ipu_fw_send_queue_token *token;
+
+	if (send_type >= N_IPU_FW_ISYS_SEND_TYPE)
+		return -EINVAL;
+
+	dev_dbg(&isys->adev->dev, "send_token: %s\n",
+		send_msg_types[send_type]);
+
+	/*
+	 * Time to flush cache in case we have some payload. Not all messages
+	 * have that
+	 */
+	if (cpu_mapped_buf)
+		clflush_cache_range(cpu_mapped_buf, size);
+
+	token = ipu_send_get_token(ctx,
+				   stream_handle + IPU_BASE_MSG_SEND_QUEUES);
+	if (!token)
+		return -EBUSY;
+
+	token->payload = dma_mapped_buf;
+	token->buf_handle = (unsigned long)cpu_mapped_buf;
+	token->send_type = send_type;
+
+	ipu_send_put_token(ctx, stream_handle + IPU_BASE_MSG_SEND_QUEUES);
+
+	return 0;
+}
+
+int ipu_fw_isys_simple_cmd(struct ipu_isys *isys,
+			   const unsigned int stream_handle,
+			   enum ipu_fw_isys_send_type send_type)
+{
+	return ipu_fw_isys_complex_cmd(isys, stream_handle, NULL, 0, 0,
+				       send_type);
+}
+
+int ipu_fw_isys_close(struct ipu_isys *isys)
+{
+	struct device *dev = &isys->adev->dev;
+	int timeout = IPU_ISYS_TURNOFF_TIMEOUT;
+	int rval;
+	unsigned long flags;
+	void *fwcom;
+
+	/*
+	 * Stop the isys fw. Actual close takes
+	 * some time as the FW must stop its actions including code fetch
+	 * to SP icache.
+	 * spinlock to wait the interrupt handler to be finished
+	 */
+	spin_lock_irqsave(&isys->power_lock, flags);
+	rval = ipu_fw_com_close(isys->fwcom);
+	fwcom = isys->fwcom;
+	isys->fwcom = NULL;
+	spin_unlock_irqrestore(&isys->power_lock, flags);
+	if (rval)
+		dev_err(dev, "Device close failure: %d\n", rval);
+
+	/* release probably fails if the close failed. Let's try still */
+	do {
+		usleep_range(IPU_ISYS_TURNOFF_DELAY_US,
+			     2 * IPU_ISYS_TURNOFF_DELAY_US);
+		rval = ipu_fw_com_release(fwcom, 0);
+		timeout--;
+	} while (rval != 0 && timeout);
+
+	if (rval) {
+		dev_err(dev, "Device release time out %d\n", rval);
+		spin_lock_irqsave(&isys->power_lock, flags);
+		isys->fwcom = fwcom;
+		spin_unlock_irqrestore(&isys->power_lock, flags);
+	}
+
+	return rval;
+}
+
+void ipu_fw_isys_cleanup(struct ipu_isys *isys)
+{
+	int ret;
+
+	ret = ipu_fw_com_release(isys->fwcom, 1);
+	if (ret < 0)
+		dev_err(&isys->adev->dev,
+			"Device busy, fw_com release failed.");
+	isys->fwcom = NULL;
+}
+
+static void start_sp(struct ipu_bus_device *adev)
+{
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	void __iomem *spc_regs_base = isys->pdata->base +
+	    isys->pdata->ipdata->hw_variant.spc_offset;
+	u32 val = 0;
+
+	val |= IPU_ISYS_SPC_STATUS_START |
+	    IPU_ISYS_SPC_STATUS_RUN |
+	    IPU_ISYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE;
+	val |= isys->icache_prefetch ? IPU_ISYS_SPC_STATUS_ICACHE_PREFETCH : 0;
+
+	writel(val, spc_regs_base + IPU_ISYS_REG_SPC_STATUS_CTRL);
+}
+
+static int query_sp(struct ipu_bus_device *adev)
+{
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	void __iomem *spc_regs_base = isys->pdata->base +
+	    isys->pdata->ipdata->hw_variant.spc_offset;
+	u32 val = readl(spc_regs_base + IPU_ISYS_REG_SPC_STATUS_CTRL);
+
+	/* return true when READY == 1, START == 0 */
+	val &= IPU_ISYS_SPC_STATUS_READY | IPU_ISYS_SPC_STATUS_START;
+
+	return val == IPU_ISYS_SPC_STATUS_READY;
+}
+
+static int ipu6_isys_fwcom_cfg_init(struct ipu_isys *isys,
+				    struct ipu_fw_com_cfg *fwcom,
+				    unsigned int num_streams)
+{
+	int i;
+	unsigned int size;
+	struct ipu_fw_syscom_queue_config *input_queue_cfg;
+	struct ipu_fw_syscom_queue_config *output_queue_cfg;
+	struct ipu6_fw_isys_fw_config *isys_fw_cfg;
+	int num_out_message_queues = 1;
+	int type_proxy = IPU_FW_ISYS_QUEUE_TYPE_PROXY;
+	int type_dev = IPU_FW_ISYS_QUEUE_TYPE_DEV;
+	int type_msg = IPU_FW_ISYS_QUEUE_TYPE_MSG;
+	int base_dev_send = IPU_BASE_DEV_SEND_QUEUES;
+	int base_msg_send = IPU_BASE_MSG_SEND_QUEUES;
+	int base_msg_recv = IPU_BASE_MSG_RECV_QUEUES;
+	int num_in_message_queues;
+	unsigned int max_streams;
+	unsigned int max_send_queues, max_sram_blocks, max_devq_size;
+
+	max_streams = IPU6_ISYS_NUM_STREAMS;
+	max_send_queues = IPU6_N_MAX_SEND_QUEUES;
+	max_sram_blocks = IPU6_NOF_SRAM_BLOCKS_MAX;
+	max_devq_size = IPU6_DEV_SEND_QUEUE_SIZE;
+	if (ipu_ver == IPU_VER_6SE) {
+		max_streams = IPU6SE_ISYS_NUM_STREAMS;
+		max_send_queues = IPU6SE_N_MAX_SEND_QUEUES;
+		max_sram_blocks = IPU6SE_NOF_SRAM_BLOCKS_MAX;
+		max_devq_size = IPU6SE_DEV_SEND_QUEUE_SIZE;
+	}
+
+	num_in_message_queues = clamp_t(unsigned int, num_streams, 1,
+					max_streams);
+	isys_fw_cfg = devm_kzalloc(&isys->adev->dev, sizeof(*isys_fw_cfg),
+				   GFP_KERNEL);
+	if (!isys_fw_cfg)
+		return -ENOMEM;
+
+	isys_fw_cfg->num_send_queues[IPU_FW_ISYS_QUEUE_TYPE_PROXY] =
+		IPU_N_MAX_PROXY_SEND_QUEUES;
+	isys_fw_cfg->num_send_queues[IPU_FW_ISYS_QUEUE_TYPE_DEV] =
+		IPU_N_MAX_DEV_SEND_QUEUES;
+	isys_fw_cfg->num_send_queues[IPU_FW_ISYS_QUEUE_TYPE_MSG] =
+		num_in_message_queues;
+	isys_fw_cfg->num_recv_queues[IPU_FW_ISYS_QUEUE_TYPE_PROXY] =
+		IPU_N_MAX_PROXY_RECV_QUEUES;
+	/* Common msg/dev return queue */
+	isys_fw_cfg->num_recv_queues[IPU_FW_ISYS_QUEUE_TYPE_DEV] = 0;
+	isys_fw_cfg->num_recv_queues[IPU_FW_ISYS_QUEUE_TYPE_MSG] =
+		num_out_message_queues;
+
+	size = sizeof(*input_queue_cfg) * max_send_queues;
+	input_queue_cfg = devm_kzalloc(&isys->adev->dev, size, GFP_KERNEL);
+	if (!input_queue_cfg)
+		return -ENOMEM;
+
+	size = sizeof(*output_queue_cfg) * IPU_N_MAX_RECV_QUEUES;
+	output_queue_cfg = devm_kzalloc(&isys->adev->dev, size, GFP_KERNEL);
+	if (!output_queue_cfg)
+		return -ENOMEM;
+
+	fwcom->input = input_queue_cfg;
+	fwcom->output = output_queue_cfg;
+
+	fwcom->num_input_queues =
+		isys_fw_cfg->num_send_queues[type_proxy] +
+		isys_fw_cfg->num_send_queues[type_dev] +
+		isys_fw_cfg->num_send_queues[type_msg];
+
+	fwcom->num_output_queues =
+		isys_fw_cfg->num_recv_queues[type_proxy] +
+		isys_fw_cfg->num_recv_queues[type_dev] +
+		isys_fw_cfg->num_recv_queues[type_msg];
+
+	/* SRAM partitioning. Equal partitioning is set. */
+	for (i = 0; i < max_sram_blocks; i++) {
+		if (i < num_in_message_queues)
+			isys_fw_cfg->buffer_partition.num_gda_pages[i] =
+				(IPU_DEVICE_GDA_NR_PAGES *
+				 IPU_DEVICE_GDA_VIRT_FACTOR) /
+				num_in_message_queues;
+		else
+			isys_fw_cfg->buffer_partition.num_gda_pages[i] = 0;
+	}
+
+	/* FW assumes proxy interface at fwcom queue 0 */
+	for (i = 0; i < isys_fw_cfg->num_send_queues[type_proxy]; i++) {
+		input_queue_cfg[i].token_size =
+			sizeof(struct ipu_fw_proxy_send_queue_token);
+		input_queue_cfg[i].queue_size = IPU_ISYS_SIZE_PROXY_SEND_QUEUE;
+	}
+
+	for (i = 0; i < isys_fw_cfg->num_send_queues[type_dev]; i++) {
+		input_queue_cfg[base_dev_send + i].token_size =
+			sizeof(struct ipu_fw_send_queue_token);
+		input_queue_cfg[base_dev_send + i].queue_size = max_devq_size;
+	}
+
+	for (i = 0; i < isys_fw_cfg->num_send_queues[type_msg]; i++) {
+		input_queue_cfg[base_msg_send + i].token_size =
+			sizeof(struct ipu_fw_send_queue_token);
+		input_queue_cfg[base_msg_send + i].queue_size =
+			IPU_ISYS_SIZE_SEND_QUEUE;
+	}
+
+	for (i = 0; i < isys_fw_cfg->num_recv_queues[type_proxy]; i++) {
+		output_queue_cfg[i].token_size =
+			sizeof(struct ipu_fw_proxy_resp_queue_token);
+		output_queue_cfg[i].queue_size = IPU_ISYS_SIZE_PROXY_RECV_QUEUE;
+	}
+	/* There is no recv DEV queue */
+	for (i = 0; i < isys_fw_cfg->num_recv_queues[type_msg]; i++) {
+		output_queue_cfg[base_msg_recv + i].token_size =
+			sizeof(struct ipu_fw_resp_queue_token);
+		output_queue_cfg[base_msg_recv + i].queue_size =
+			IPU_ISYS_SIZE_RECV_QUEUE;
+	}
+
+	fwcom->dmem_addr = isys->pdata->ipdata->hw_variant.dmem_offset;
+	fwcom->specific_addr = isys_fw_cfg;
+	fwcom->specific_size = sizeof(*isys_fw_cfg);
+
+	return 0;
+}
+
+int ipu_fw_isys_init(struct ipu_isys *isys, unsigned int num_streams)
+{
+	int retry = IPU_ISYS_OPEN_RETRY;
+
+	struct ipu_fw_com_cfg fwcom = {
+		.cell_start = start_sp,
+		.cell_ready = query_sp,
+		.buttress_boot_offset = SYSCOM_BUTTRESS_FW_PARAMS_ISYS_OFFSET,
+	};
+
+	struct device *dev = &isys->adev->dev;
+	int rval;
+
+	ipu6_isys_fwcom_cfg_init(isys, &fwcom, num_streams);
+
+	isys->fwcom = ipu_fw_com_prepare(&fwcom, isys->adev, isys->pdata->base);
+	if (!isys->fwcom) {
+		dev_err(dev, "isys fw com prepare failed\n");
+		return -EIO;
+	}
+
+	rval = ipu_fw_com_open(isys->fwcom);
+	if (rval) {
+		dev_err(dev, "isys fw com open failed %d\n", rval);
+		return rval;
+	}
+
+	do {
+		usleep_range(IPU_ISYS_OPEN_TIMEOUT_US,
+			     IPU_ISYS_OPEN_TIMEOUT_US + 10);
+		rval = ipu_fw_com_ready(isys->fwcom);
+		if (!rval)
+			break;
+		retry--;
+	} while (retry > 0);
+
+	if (!retry && rval) {
+		dev_err(dev, "isys port open ready failed %d\n", rval);
+		ipu_fw_isys_close(isys);
+	}
+
+	return rval;
+}
+
+struct ipu_fw_isys_resp_info_abi *
+ipu_fw_isys_get_resp(void *context, unsigned int queue,
+		     struct ipu_fw_isys_resp_info_abi *response)
+{
+	return (struct ipu_fw_isys_resp_info_abi *)
+	    ipu_recv_get_token(context, queue);
+}
+
+void ipu_fw_isys_put_resp(void *context, unsigned int queue)
+{
+	ipu_recv_put_token(context, queue);
+}
+
+void ipu_fw_isys_set_params(struct ipu_fw_isys_stream_cfg_data_abi *stream_cfg)
+{
+	unsigned int i;
+	unsigned int idx;
+
+	for (i = 0; i < stream_cfg->nof_input_pins; i++) {
+		idx = stream_cfg->input_pins[i].dt;
+		stream_cfg->input_pins[i].bits_per_pix =
+		    extracted_bits_per_pixel_per_mipi_data_type[idx];
+		stream_cfg->input_pins[i].mapped_dt =
+		    N_IPU_FW_ISYS_MIPI_DATA_TYPE;
+		stream_cfg->input_pins[i].mipi_decompression =
+		    IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_NO_COMPRESSION;
+		/*
+		 * CSI BE can be used to crop and change bayer order.
+		 * NOTE: currently it only crops first and last lines in height.
+		 */
+		if (stream_cfg->crop.top_offset & 1)
+			stream_cfg->input_pins[i].crop_first_and_last_lines = 1;
+		stream_cfg->input_pins[i].capture_mode =
+			IPU_FW_ISYS_CAPTURE_MODE_REGULAR;
+	}
+}
+
+void
+ipu_fw_isys_dump_stream_cfg(struct device *dev,
+			    struct ipu_fw_isys_stream_cfg_data_abi *stream_cfg)
+{
+	unsigned int i;
+
+	dev_dbg(dev, "---------------------------\n");
+	dev_dbg(dev, "IPU_FW_ISYS_STREAM_CFG_DATA\n");
+	dev_dbg(dev, "---------------------------\n");
+
+	dev_dbg(dev, "Source %d\n", stream_cfg->src);
+	dev_dbg(dev, "VC %d\n", stream_cfg->vc);
+	dev_dbg(dev, "Nof input pins %d\n", stream_cfg->nof_input_pins);
+	dev_dbg(dev, "Nof output pins %d\n", stream_cfg->nof_output_pins);
+
+	for (i = 0; i < stream_cfg->nof_input_pins; i++) {
+		dev_dbg(dev, "Input pin %d\n", i);
+		dev_dbg(dev, "Mipi data type 0x%0x\n",
+			stream_cfg->input_pins[i].dt);
+		dev_dbg(dev, "Mipi store mode %d\n",
+			stream_cfg->input_pins[i].mipi_store_mode);
+		dev_dbg(dev, "Bits per pixel %d\n",
+			stream_cfg->input_pins[i].bits_per_pix);
+		dev_dbg(dev, "Mapped data type 0x%0x\n",
+			stream_cfg->input_pins[i].mapped_dt);
+		dev_dbg(dev, "Input res width %d\n",
+			stream_cfg->input_pins[i].input_res.width);
+		dev_dbg(dev, "Input res height %d\n",
+			stream_cfg->input_pins[i].input_res.height);
+		dev_dbg(dev, "mipi decompression %d\n",
+			stream_cfg->input_pins[i].mipi_decompression);
+		dev_dbg(dev, "capture_mode %d\n",
+			stream_cfg->input_pins[i].capture_mode);
+	}
+
+	dev_dbg(dev, "Crop info\n");
+	dev_dbg(dev, "Crop.top_offset %d\n", stream_cfg->crop.top_offset);
+	dev_dbg(dev, "Crop.left_offset %d\n", stream_cfg->crop.left_offset);
+	dev_dbg(dev, "Crop.bottom_offset %d\n",
+		stream_cfg->crop.bottom_offset);
+	dev_dbg(dev, "Crop.right_offset %d\n", stream_cfg->crop.right_offset);
+	dev_dbg(dev, "----------------\n");
+
+	for (i = 0; i < stream_cfg->nof_output_pins; i++) {
+		dev_dbg(dev, "Output pin %d\n", i);
+		dev_dbg(dev, "Output input pin id %d\n",
+			stream_cfg->output_pins[i].input_pin_id);
+		dev_dbg(dev, "Output res width %d\n",
+			stream_cfg->output_pins[i].output_res.width);
+		dev_dbg(dev, "Output res height %d\n",
+			stream_cfg->output_pins[i].output_res.height);
+		dev_dbg(dev, "Stride %d\n", stream_cfg->output_pins[i].stride);
+		dev_dbg(dev, "Pin type %d\n", stream_cfg->output_pins[i].pt);
+		dev_dbg(dev, "Payload %d\n",
+			stream_cfg->output_pins[i].payload_buf_size);
+		dev_dbg(dev, "Ft %d\n", stream_cfg->output_pins[i].ft);
+		dev_dbg(dev, "Watermar in lines %d\n",
+			stream_cfg->output_pins[i].watermark_in_lines);
+		dev_dbg(dev, "Send irq %d\n",
+			stream_cfg->output_pins[i].send_irq);
+		dev_dbg(dev, "Reserve compression %d\n",
+			stream_cfg->output_pins[i].reserve_compression);
+		dev_dbg(dev, "snoopable %d\n",
+			stream_cfg->output_pins[i].snoopable);
+		dev_dbg(dev, "error_handling_enable %d\n",
+			stream_cfg->output_pins[i].error_handling_enable);
+		dev_dbg(dev, "sensor type %d\n",
+			stream_cfg->output_pins[i].sensor_type);
+		dev_dbg(dev, "----------------\n");
+	}
+
+	dev_dbg(dev, "Isl_use %d\n", stream_cfg->isl_use);
+	dev_dbg(dev, "stream sensor_type %d\n", stream_cfg->sensor_type);
+
+}
+
+void ipu_fw_isys_dump_frame_buff_set(struct device *dev,
+				     struct ipu_fw_isys_frame_buff_set_abi *buf,
+				     unsigned int outputs)
+{
+	unsigned int i;
+
+	dev_dbg(dev, "--------------------------\n");
+	dev_dbg(dev, "IPU_FW_ISYS_FRAME_BUFF_SET\n");
+	dev_dbg(dev, "--------------------------\n");
+
+	for (i = 0; i < outputs; i++) {
+		dev_dbg(dev, "Output pin %d\n", i);
+		dev_dbg(dev, "out_buf_id %llu\n",
+			buf->output_pins[i].out_buf_id);
+		dev_dbg(dev, "addr 0x%x\n", buf->output_pins[i].addr);
+		dev_dbg(dev, "compress %u\n", buf->output_pins[i].compress);
+
+		dev_dbg(dev, "----------------\n");
+	}
+
+	dev_dbg(dev, "send_irq_sof 0x%x\n", buf->send_irq_sof);
+	dev_dbg(dev, "send_irq_eof 0x%x\n", buf->send_irq_eof);
+	dev_dbg(dev, "send_resp_sof 0x%x\n", buf->send_resp_sof);
+	dev_dbg(dev, "send_resp_eof 0x%x\n", buf->send_resp_eof);
+	dev_dbg(dev, "send_irq_capture_ack 0x%x\n", buf->send_irq_capture_ack);
+	dev_dbg(dev, "send_irq_capture_done 0x%x\n",
+		buf->send_irq_capture_done);
+	dev_dbg(dev, "send_resp_capture_ack 0x%x\n",
+		buf->send_resp_capture_ack);
+	dev_dbg(dev, "send_resp_capture_done 0x%x\n",
+		buf->send_resp_capture_done);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-fw-isys.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-fw-isys.h
@@ -0,0 +1,816 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_FW_ISYS_H
+#define IPU_FW_ISYS_H
+
+#include "ipu-fw-com.h"
+
+/* Max number of Input/Output Pins */
+#define IPU_MAX_IPINS 4
+
+#define IPU_MAX_OPINS ((IPU_MAX_IPINS) + 1)
+
+#define IPU6_STREAM_ID_MAX 16
+#define IPU6_NONSECURE_STREAM_ID_MAX 12
+#define IPU6_DEV_SEND_QUEUE_SIZE (IPU6_STREAM_ID_MAX)
+#define IPU6_NOF_SRAM_BLOCKS_MAX (IPU6_STREAM_ID_MAX)
+#define IPU6_N_MAX_MSG_SEND_QUEUES (IPU6_STREAM_ID_MAX)
+#define IPU6SE_STREAM_ID_MAX 8
+#define IPU6SE_NONSECURE_STREAM_ID_MAX 4
+#define IPU6SE_DEV_SEND_QUEUE_SIZE (IPU6SE_STREAM_ID_MAX)
+#define IPU6SE_NOF_SRAM_BLOCKS_MAX (IPU6SE_STREAM_ID_MAX)
+#define IPU6SE_N_MAX_MSG_SEND_QUEUES (IPU6SE_STREAM_ID_MAX)
+
+/* Single return queue for all streams/commands type */
+#define IPU_N_MAX_MSG_RECV_QUEUES 1
+/* Single device queue for high priority commands (bypass in-order queue) */
+#define IPU_N_MAX_DEV_SEND_QUEUES 1
+/* Single dedicated send queue for proxy interface */
+#define IPU_N_MAX_PROXY_SEND_QUEUES 1
+/* Single dedicated recv queue for proxy interface */
+#define IPU_N_MAX_PROXY_RECV_QUEUES 1
+/* Send queues layout */
+#define IPU_BASE_PROXY_SEND_QUEUES 0
+#define IPU_BASE_DEV_SEND_QUEUES \
+	(IPU_BASE_PROXY_SEND_QUEUES + IPU_N_MAX_PROXY_SEND_QUEUES)
+#define IPU_BASE_MSG_SEND_QUEUES \
+	(IPU_BASE_DEV_SEND_QUEUES + IPU_N_MAX_DEV_SEND_QUEUES)
+/* Recv queues layout */
+#define IPU_BASE_PROXY_RECV_QUEUES 0
+#define IPU_BASE_MSG_RECV_QUEUES \
+	(IPU_BASE_PROXY_RECV_QUEUES + IPU_N_MAX_PROXY_RECV_QUEUES)
+#define IPU_N_MAX_RECV_QUEUES \
+	(IPU_BASE_MSG_RECV_QUEUES + IPU_N_MAX_MSG_RECV_QUEUES)
+
+#define IPU6_N_MAX_SEND_QUEUES \
+	(IPU_BASE_MSG_SEND_QUEUES + IPU6_N_MAX_MSG_SEND_QUEUES)
+#define IPU6SE_N_MAX_SEND_QUEUES \
+	(IPU_BASE_MSG_SEND_QUEUES + IPU6SE_N_MAX_MSG_SEND_QUEUES)
+
+/* Max number of supported input pins routed in ISL */
+#define IPU_MAX_IPINS_IN_ISL 2
+
+/* Max number of planes for frame formats supported by the FW */
+#define IPU_PIN_PLANES_MAX 4
+
+/**
+ * enum ipu_fw_isys_resp_type
+ */
+enum ipu_fw_isys_resp_type {
+	IPU_FW_ISYS_RESP_TYPE_STREAM_OPEN_DONE = 0,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_START_ACK,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_START_AND_CAPTURE_ACK,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_ACK,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_STOP_ACK,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_FLUSH_ACK,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_CLOSE_ACK,
+	IPU_FW_ISYS_RESP_TYPE_PIN_DATA_READY,
+	IPU_FW_ISYS_RESP_TYPE_PIN_DATA_WATERMARK,
+	IPU_FW_ISYS_RESP_TYPE_FRAME_SOF,
+	IPU_FW_ISYS_RESP_TYPE_FRAME_EOF,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_START_AND_CAPTURE_DONE,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_DONE,
+	IPU_FW_ISYS_RESP_TYPE_PIN_DATA_SKIPPED,
+	IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_SKIPPED,
+	IPU_FW_ISYS_RESP_TYPE_FRAME_SOF_DISCARDED,
+	IPU_FW_ISYS_RESP_TYPE_FRAME_EOF_DISCARDED,
+	IPU_FW_ISYS_RESP_TYPE_STATS_DATA_READY,
+	N_IPU_FW_ISYS_RESP_TYPE
+};
+
+/**
+ * enum ipu_fw_isys_send_type
+ */
+enum ipu_fw_isys_send_type {
+	IPU_FW_ISYS_SEND_TYPE_STREAM_OPEN = 0,
+	IPU_FW_ISYS_SEND_TYPE_STREAM_START,
+	IPU_FW_ISYS_SEND_TYPE_STREAM_START_AND_CAPTURE,
+	IPU_FW_ISYS_SEND_TYPE_STREAM_CAPTURE,
+	IPU_FW_ISYS_SEND_TYPE_STREAM_STOP,
+	IPU_FW_ISYS_SEND_TYPE_STREAM_FLUSH,
+	IPU_FW_ISYS_SEND_TYPE_STREAM_CLOSE,
+	N_IPU_FW_ISYS_SEND_TYPE
+};
+
+/**
+ * enum ipu_fw_isys_queue_type
+ */
+enum ipu_fw_isys_queue_type {
+	IPU_FW_ISYS_QUEUE_TYPE_PROXY = 0,
+	IPU_FW_ISYS_QUEUE_TYPE_DEV,
+	IPU_FW_ISYS_QUEUE_TYPE_MSG,
+	N_IPU_FW_ISYS_QUEUE_TYPE
+};
+
+/**
+ * enum ipu_fw_isys_stream_source: Specifies a source for a stream
+ */
+enum ipu_fw_isys_stream_source {
+	IPU_FW_ISYS_STREAM_SRC_PORT_0 = 0,
+	IPU_FW_ISYS_STREAM_SRC_PORT_1,
+	IPU_FW_ISYS_STREAM_SRC_PORT_2,
+	IPU_FW_ISYS_STREAM_SRC_PORT_3,
+	IPU_FW_ISYS_STREAM_SRC_PORT_4,
+	IPU_FW_ISYS_STREAM_SRC_PORT_5,
+	IPU_FW_ISYS_STREAM_SRC_PORT_6,
+	IPU_FW_ISYS_STREAM_SRC_PORT_7,
+	IPU_FW_ISYS_STREAM_SRC_PORT_8,
+	IPU_FW_ISYS_STREAM_SRC_PORT_9,
+	IPU_FW_ISYS_STREAM_SRC_PORT_10,
+	IPU_FW_ISYS_STREAM_SRC_PORT_11,
+	IPU_FW_ISYS_STREAM_SRC_PORT_12,
+	IPU_FW_ISYS_STREAM_SRC_PORT_13,
+	IPU_FW_ISYS_STREAM_SRC_PORT_14,
+	IPU_FW_ISYS_STREAM_SRC_PORT_15,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_0,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_1,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_2,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_3,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_4,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_5,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_6,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_7,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_8,
+	IPU_FW_ISYS_STREAM_SRC_MIPIGEN_9,
+	N_IPU_FW_ISYS_STREAM_SRC
+};
+
+enum ipu_fw_isys_sensor_type {
+	/* non-snoopable to PSYS */
+	IPU_FW_ISYS_VC1_SENSOR_DATA	= 0,
+	/* non-snoopable for PDAF */
+	IPU_FW_ISYS_VC1_SENSOR_PDAF,
+	/* snoopable to CPU */
+	IPU_FW_ISYS_VC0_SENSOR_METADATA,
+	/* snoopable to CPU */
+	IPU_FW_ISYS_VC0_SENSOR_DATA,
+	N_IPU_FW_ISYS_SENSOR_TYPE
+};
+
+enum ipu6se_fw_isys_sensor_info {
+	/* VC1 */
+	IPU6SE_FW_ISYS_SENSOR_DATA_1 = 1,
+	IPU6SE_FW_ISYS_SENSOR_DATA_2 = 2,
+	IPU6SE_FW_ISYS_SENSOR_DATA_3 = 3,
+	IPU6SE_FW_ISYS_SENSOR_PDAF_1 = 4,
+	IPU6SE_FW_ISYS_SENSOR_PDAF_2 = 4,
+	/* VC0 */
+	IPU6SE_FW_ISYS_SENSOR_METADATA = 5,
+	IPU6SE_FW_ISYS_SENSOR_DATA_4 = 6,
+	IPU6SE_FW_ISYS_SENSOR_DATA_5 = 7,
+	IPU6SE_FW_ISYS_SENSOR_DATA_6 = 8,
+	IPU6SE_FW_ISYS_SENSOR_DATA_7 = 9,
+	IPU6SE_FW_ISYS_SENSOR_DATA_8 = 10,
+	IPU6SE_FW_ISYS_SENSOR_DATA_9 = 11,
+	N_IPU6SE_FW_ISYS_SENSOR_INFO,
+	IPU6SE_FW_ISYS_VC1_SENSOR_DATA_START = IPU6SE_FW_ISYS_SENSOR_DATA_1,
+	IPU6SE_FW_ISYS_VC1_SENSOR_DATA_END = IPU6SE_FW_ISYS_SENSOR_DATA_3,
+	IPU6SE_FW_ISYS_VC0_SENSOR_DATA_START = IPU6SE_FW_ISYS_SENSOR_DATA_4,
+	IPU6SE_FW_ISYS_VC0_SENSOR_DATA_END = IPU6SE_FW_ISYS_SENSOR_DATA_9,
+	IPU6SE_FW_ISYS_VC1_SENSOR_PDAF_START = IPU6SE_FW_ISYS_SENSOR_PDAF_1,
+	IPU6SE_FW_ISYS_VC1_SENSOR_PDAF_END = IPU6SE_FW_ISYS_SENSOR_PDAF_2,
+};
+
+enum ipu6_fw_isys_sensor_info {
+	/* VC1 */
+	IPU6_FW_ISYS_SENSOR_DATA_1 = 1,
+	IPU6_FW_ISYS_SENSOR_DATA_2 = 2,
+	IPU6_FW_ISYS_SENSOR_DATA_3 = 3,
+	IPU6_FW_ISYS_SENSOR_DATA_4 = 4,
+	IPU6_FW_ISYS_SENSOR_DATA_5 = 5,
+	IPU6_FW_ISYS_SENSOR_DATA_6 = 6,
+	IPU6_FW_ISYS_SENSOR_DATA_7 = 7,
+	IPU6_FW_ISYS_SENSOR_DATA_8 = 8,
+	IPU6_FW_ISYS_SENSOR_DATA_9 = 9,
+	IPU6_FW_ISYS_SENSOR_DATA_10 = 10,
+	IPU6_FW_ISYS_SENSOR_PDAF_1 = 11,
+	IPU6_FW_ISYS_SENSOR_PDAF_2 = 12,
+	/* VC0 */
+	IPU6_FW_ISYS_SENSOR_METADATA = 13,
+	IPU6_FW_ISYS_SENSOR_DATA_11 = 14,
+	IPU6_FW_ISYS_SENSOR_DATA_12 = 15,
+	IPU6_FW_ISYS_SENSOR_DATA_13 = 16,
+	IPU6_FW_ISYS_SENSOR_DATA_14 = 17,
+	IPU6_FW_ISYS_SENSOR_DATA_15 = 18,
+	IPU6_FW_ISYS_SENSOR_DATA_16 = 19,
+	N_IPU6_FW_ISYS_SENSOR_INFO,
+	IPU6_FW_ISYS_VC1_SENSOR_DATA_START = IPU6_FW_ISYS_SENSOR_DATA_1,
+	IPU6_FW_ISYS_VC1_SENSOR_DATA_END = IPU6_FW_ISYS_SENSOR_DATA_10,
+	IPU6_FW_ISYS_VC0_SENSOR_DATA_START = IPU6_FW_ISYS_SENSOR_DATA_11,
+	IPU6_FW_ISYS_VC0_SENSOR_DATA_END = IPU6_FW_ISYS_SENSOR_DATA_16,
+	IPU6_FW_ISYS_VC1_SENSOR_PDAF_START = IPU6_FW_ISYS_SENSOR_PDAF_1,
+	IPU6_FW_ISYS_VC1_SENSOR_PDAF_END = IPU6_FW_ISYS_SENSOR_PDAF_2,
+};
+
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_PORT0 IPU_FW_ISYS_STREAM_SRC_PORT_0
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_PORT1 IPU_FW_ISYS_STREAM_SRC_PORT_1
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_PORT2 IPU_FW_ISYS_STREAM_SRC_PORT_2
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_PORT3 IPU_FW_ISYS_STREAM_SRC_PORT_3
+
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_3PH_PORTA IPU_FW_ISYS_STREAM_SRC_PORT_4
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_3PH_PORTB IPU_FW_ISYS_STREAM_SRC_PORT_5
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_3PH_CPHY_PORT0 IPU_FW_ISYS_STREAM_SRC_PORT_6
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_3PH_CPHY_PORT1 IPU_FW_ISYS_STREAM_SRC_PORT_7
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_3PH_CPHY_PORT2 IPU_FW_ISYS_STREAM_SRC_PORT_8
+#define IPU_FW_ISYS_STREAM_SRC_CSI2_3PH_CPHY_PORT3 IPU_FW_ISYS_STREAM_SRC_PORT_9
+
+#define IPU_FW_ISYS_STREAM_SRC_MIPIGEN_PORT0 IPU_FW_ISYS_STREAM_SRC_MIPIGEN_0
+#define IPU_FW_ISYS_STREAM_SRC_MIPIGEN_PORT1 IPU_FW_ISYS_STREAM_SRC_MIPIGEN_1
+
+/**
+ * enum ipu_fw_isys_mipi_vc: MIPI csi2 spec
+ * supports up to 4 virtual per physical channel
+ */
+enum ipu_fw_isys_mipi_vc {
+	IPU_FW_ISYS_MIPI_VC_0 = 0,
+	IPU_FW_ISYS_MIPI_VC_1,
+	IPU_FW_ISYS_MIPI_VC_2,
+	IPU_FW_ISYS_MIPI_VC_3,
+	N_IPU_FW_ISYS_MIPI_VC
+};
+
+/**
+ *  Supported Pixel Frame formats. Expandable if needed
+ */
+enum ipu_fw_isys_frame_format_type {
+	IPU_FW_ISYS_FRAME_FORMAT_NV11 = 0, /* 12 bit YUV 411, Y, UV plane */
+	IPU_FW_ISYS_FRAME_FORMAT_NV12,	/* 12 bit YUV 420, Y, UV plane */
+	IPU_FW_ISYS_FRAME_FORMAT_NV12_16, /* 16 bit YUV 420, Y, UV plane */
+	IPU_FW_ISYS_FRAME_FORMAT_NV12_TILEY, /* 12 bit YUV 420,
+					      * Intel proprietary tiled format,
+					      * TileY
+					      */
+	IPU_FW_ISYS_FRAME_FORMAT_NV16,	/* 16 bit YUV 422, Y, UV plane */
+	IPU_FW_ISYS_FRAME_FORMAT_NV21,	/* 12 bit YUV 420, Y, VU plane */
+	IPU_FW_ISYS_FRAME_FORMAT_NV61,	/* 16 bit YUV 422, Y, VU plane */
+	IPU_FW_ISYS_FRAME_FORMAT_YV12,	/* 12 bit YUV 420, Y, V, U plane */
+	IPU_FW_ISYS_FRAME_FORMAT_YV16,	/* 16 bit YUV 422, Y, V, U plane */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV420, /* 12 bit YUV 420, Y, U, V plane */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV420_10, /* yuv420, 10 bits per subpixel */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV420_12, /* yuv420, 12 bits per subpixel */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV420_14, /* yuv420, 14 bits per subpixel */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV420_16, /* yuv420, 16 bits per subpixel */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV422, /* 16 bit YUV 422, Y, U, V plane */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV422_16, /* yuv422, 16 bits per subpixel */
+	IPU_FW_ISYS_FRAME_FORMAT_UYVY,	/* 16 bit YUV 422, UYVY interleaved */
+	IPU_FW_ISYS_FRAME_FORMAT_YUYV,	/* 16 bit YUV 422, YUYV interleaved */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV444, /* 24 bit YUV 444, Y, U, V plane */
+	IPU_FW_ISYS_FRAME_FORMAT_YUV_LINE, /* Internal format, 2 y lines
+					    * followed by a uvinterleaved line
+					    */
+	IPU_FW_ISYS_FRAME_FORMAT_RAW8,	/* RAW8, 1 plane */
+	IPU_FW_ISYS_FRAME_FORMAT_RAW10,	/* RAW10, 1 plane */
+	IPU_FW_ISYS_FRAME_FORMAT_RAW12,	/* RAW12, 1 plane */
+	IPU_FW_ISYS_FRAME_FORMAT_RAW14,	/* RAW14, 1 plane */
+	IPU_FW_ISYS_FRAME_FORMAT_RAW16,	/* RAW16, 1 plane */
+	IPU_FW_ISYS_FRAME_FORMAT_RGB565, /* 16 bit RGB, 1 plane. Each 3 sub
+					  * pixels are packed into one 16 bit
+					  * value, 5 bits for R, 6 bits
+					  *   for G and 5 bits for B.
+					  */
+
+	IPU_FW_ISYS_FRAME_FORMAT_PLANAR_RGB888,	/* 24 bit RGB, 3 planes */
+	IPU_FW_ISYS_FRAME_FORMAT_RGBA888,	/* 32 bit RGBA, 1 plane,
+						 * A=Alpha (alpha is unused)
+						 */
+	IPU_FW_ISYS_FRAME_FORMAT_QPLANE6,	/* Internal, for advanced ISP */
+	IPU_FW_ISYS_FRAME_FORMAT_BINARY_8, /* byte stream, used for jpeg. */
+	N_IPU_FW_ISYS_FRAME_FORMAT
+};
+
+/* Temporary for driver compatibility */
+#define IPU_FW_ISYS_FRAME_FORMAT_RAW		(IPU_FW_ISYS_FRAME_FORMAT_RAW16)
+
+enum ipu_fw_isys_mipi_compression_type {
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_NO_COMPRESSION = 0,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_10_8_10_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_10_8_10_TYPE2,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_10_7_10_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_10_7_10_TYPE2,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_10_6_10_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_10_6_10_TYPE2,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_8_12_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_8_12_TYPE2,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_7_12_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_7_12_TYPE2,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_6_12_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_6_12_TYPE2,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_10_12_TYPE1,
+	IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_12_10_12_TYPE2,
+	N_IPU_FW_ISYS_MIPI_COMPRESSION_TYPE,
+};
+
+/**
+ *  Supported MIPI data type. Keep in sync array in ipu_fw_isys_private.c
+ */
+enum ipu_fw_isys_mipi_data_type {
+	/** SYNCHRONIZATION SHORT PACKET DATA TYPES */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_FRAME_START_CODE = 0x00,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_FRAME_END_CODE = 0x01,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_LINE_START_CODE = 0x02,	/* Optional */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_LINE_END_CODE = 0x03,	/* Optional */
+	/** Reserved 0x04-0x07 */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x04 = 0x04,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x05 = 0x05,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x06 = 0x06,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x07 = 0x07,
+	/** GENERIC SHORT PACKET DATA TYPES */
+	/** They are used to keep the timing information for
+	 * the opening/closing of shutters,
+	 *  triggering of flashes and etc.
+	 */
+	/* Generic Short Packet Codes 1 - 8 */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT1 = 0x08,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT2 = 0x09,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT3 = 0x0A,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT4 = 0x0B,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT5 = 0x0C,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT6 = 0x0D,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT7 = 0x0E,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_GENERIC_SHORT8 = 0x0F,
+	/** GENERIC LONG PACKET DATA TYPES */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_NULL = 0x10,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_BLANKING_DATA = 0x11,
+	/* Embedded 8-bit non Image Data */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_EMBEDDED = 0x12,
+	/** Reserved 0x13-0x17 */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x13 = 0x13,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x14 = 0x14,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x15 = 0x15,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x16 = 0x16,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x17 = 0x17,
+	/** YUV DATA TYPES */
+	/* 8 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_8 = 0x18,
+	/* 10 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_10 = 0x19,
+	/* 8 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_8_LEGACY = 0x1A,
+	/** Reserved 0x1B */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x1B = 0x1B,
+	/* YUV420 8-bit Chroma Shifted Pixel Sampling) */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_8_SHIFT = 0x1C,
+	/* YUV420 8-bit (Chroma Shifted Pixel Sampling) */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV420_10_SHIFT = 0x1D,
+	/* UYVY..UVYV, 8 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV422_8 = 0x1E,
+	/* UYVY..UVYV, 10 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_YUV422_10 = 0x1F,
+	/** RGB DATA TYPES */
+	/* BGR..BGR, 4 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_444 = 0x20,
+	/* BGR..BGR, 5 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_555 = 0x21,
+	/* BGR..BGR, 5 bits B and R, 6 bits G */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_565 = 0x22,
+	/* BGR..BGR, 6 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_666 = 0x23,
+	/* BGR..BGR, 8 bits per subpixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RGB_888 = 0x24,
+	/** Reserved 0x25-0x27 */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x25 = 0x25,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x26 = 0x26,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x27 = 0x27,
+	/** RAW DATA TYPES */
+	/* RAW data, 6 - 14 bits per pixel */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_6 = 0x28,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_7 = 0x29,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_8 = 0x2A,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_10 = 0x2B,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_12 = 0x2C,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_14 = 0x2D,
+	/** Reserved 0x2E-2F are used with assigned meaning */
+	/* RAW data, 16 bits per pixel, not specified in CSI-MIPI standard */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RAW_16 = 0x2E,
+	/* Binary byte stream, which is target at JPEG,
+	 * not specified in CSI-MIPI standard
+	 */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_BINARY_8 = 0x2F,
+
+	/** USER DEFINED 8-BIT DATA TYPES */
+	/** For example, the data transmitter (e.g. the SoC sensor)
+	 * can keep the JPEG data as
+	 *  the User Defined Data Type 4 and the MPEG data as the
+	 *  User Defined Data Type 7.
+	 */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF1 = 0x30,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF2 = 0x31,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF3 = 0x32,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF4 = 0x33,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF5 = 0x34,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF6 = 0x35,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF7 = 0x36,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_USER_DEF8 = 0x37,
+	/** Reserved 0x38-0x3F */
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x38 = 0x38,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x39 = 0x39,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x3A = 0x3A,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x3B = 0x3B,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x3C = 0x3C,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x3D = 0x3D,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x3E = 0x3E,
+	IPU_FW_ISYS_MIPI_DATA_TYPE_RESERVED_0x3F = 0x3F,
+
+	/* Keep always last and max value */
+	N_IPU_FW_ISYS_MIPI_DATA_TYPE = 0x40
+};
+
+/** enum ipu_fw_isys_pin_type: output pin buffer types.
+ * Buffers can be queued and de-queued to hand them over between IA and ISYS
+ */
+enum ipu_fw_isys_pin_type {
+	/* Captured as MIPI packets */
+	IPU_FW_ISYS_PIN_TYPE_MIPI = 0,
+	/* Captured through the RAW path */
+	IPU_FW_ISYS_PIN_TYPE_RAW_NS = 1,
+	/* Captured through the SoC path */
+	IPU_FW_ISYS_PIN_TYPE_RAW_SOC = 3,
+	/* Reserved for future use, maybe short packets */
+	IPU_FW_ISYS_PIN_TYPE_METADATA_0 = 4,
+	/* Reserved for future use */
+	IPU_FW_ISYS_PIN_TYPE_METADATA_1 = 5,
+	/* Keep always last and max value */
+	N_IPU_FW_ISYS_PIN_TYPE
+};
+
+/**
+ * enum ipu_fw_isys_mipi_store_mode. Describes if long MIPI packets reach
+ * MIPI SRAM with the long packet header or
+ * if not, then only option is to capture it with pin type MIPI.
+ */
+enum ipu_fw_isys_mipi_store_mode {
+	IPU_FW_ISYS_MIPI_STORE_MODE_NORMAL = 0,
+	IPU_FW_ISYS_MIPI_STORE_MODE_DISCARD_LONG_HEADER,
+	N_IPU_FW_ISYS_MIPI_STORE_MODE
+};
+
+/**
+ * ISYS capture mode and sensor enums
+ * Used for Tobii sensor, if doubt, use default value 0
+ */
+
+enum ipu_fw_isys_capture_mode {
+	IPU_FW_ISYS_CAPTURE_MODE_REGULAR = 0,
+	IPU_FW_ISYS_CAPTURE_MODE_BURST,
+	N_IPU_FW_ISYS_CAPTURE_MODE,
+};
+
+enum ipu_fw_isys_sensor_mode {
+	IPU_FW_ISYS_SENSOR_MODE_NORMAL = 0,
+	IPU_FW_ISYS_SENSOR_MODE_TOBII,
+	N_IPU_FW_ISYS_SENSOR_MODE,
+};
+
+/**
+ * enum ipu_fw_isys_error. Describes the error type detected by the FW
+ */
+enum ipu_fw_isys_error {
+	IPU_FW_ISYS_ERROR_NONE = 0,	/* No details */
+	IPU_FW_ISYS_ERROR_FW_INTERNAL_CONSISTENCY,	/* enum */
+	IPU_FW_ISYS_ERROR_HW_CONSISTENCY,	/* enum */
+	IPU_FW_ISYS_ERROR_DRIVER_INVALID_COMMAND_SEQUENCE,	/* enum */
+	IPU_FW_ISYS_ERROR_DRIVER_INVALID_DEVICE_CONFIGURATION,	/* enum */
+	IPU_FW_ISYS_ERROR_DRIVER_INVALID_STREAM_CONFIGURATION,	/* enum */
+	IPU_FW_ISYS_ERROR_DRIVER_INVALID_FRAME_CONFIGURATION,	/* enum */
+	IPU_FW_ISYS_ERROR_INSUFFICIENT_RESOURCES,	/* enum */
+	IPU_FW_ISYS_ERROR_HW_REPORTED_STR2MMIO,	/* HW code */
+	IPU_FW_ISYS_ERROR_HW_REPORTED_SIG2CIO,	/* HW code */
+	IPU_FW_ISYS_ERROR_SENSOR_FW_SYNC,	/* enum */
+	IPU_FW_ISYS_ERROR_STREAM_IN_SUSPENSION,	/* FW code */
+	IPU_FW_ISYS_ERROR_RESPONSE_QUEUE_FULL,	/* FW code */
+	N_IPU_FW_ISYS_ERROR
+};
+
+/**
+ * enum ipu_fw_proxy_error. Describes the error type for
+ * the proxy detected by the FW
+ */
+enum ipu_fw_proxy_error {
+	IPU_FW_PROXY_ERROR_NONE = 0,
+	IPU_FW_PROXY_ERROR_INVALID_WRITE_REGION,
+	IPU_FW_PROXY_ERROR_INVALID_WRITE_OFFSET,
+	N_IPU_FW_PROXY_ERROR
+};
+
+struct ipu_isys;
+
+struct ipu6_fw_isys_buffer_partition_abi {
+	u32 num_gda_pages[IPU6_STREAM_ID_MAX];
+};
+
+struct ipu6_fw_isys_fw_config {
+	struct ipu6_fw_isys_buffer_partition_abi buffer_partition;
+	u32 num_send_queues[N_IPU_FW_ISYS_QUEUE_TYPE];
+	u32 num_recv_queues[N_IPU_FW_ISYS_QUEUE_TYPE];
+};
+
+/**
+ * struct ipu_fw_isys_resolution_abi: Generic resolution structure.
+ * @Width
+ * @Height
+ */
+struct ipu_fw_isys_resolution_abi {
+	u32 width;
+	u32 height;
+};
+
+/**
+ * struct ipu_fw_isys_output_pin_payload_abi
+ * @out_buf_id: Points to output pin buffer - buffer identifier
+ * @addr: Points to output pin buffer - CSS Virtual Address
+ * @compress: Request frame compression (1), or  not (0)
+ */
+struct ipu_fw_isys_output_pin_payload_abi {
+	u64 out_buf_id;
+	u32 addr;
+	u32 compress;
+};
+
+/**
+ * struct ipu_fw_isys_output_pin_info_abi
+ * @output_res: output pin resolution
+ * @stride: output stride in Bytes (not valid for statistics)
+ * @watermark_in_lines: pin watermark level in lines
+ * @payload_buf_size: minimum size in Bytes of all buffers that will be
+ *			supplied for capture on this pin
+ * @send_irq: assert if pin event should trigger irq
+ * @pt: pin type -real format "enum ipu_fw_isys_pin_type"
+ * @ft: frame format type -real format "enum ipu_fw_isys_frame_format_type"
+ * @input_pin_id: related input pin id
+ * @reserve_compression: reserve compression resources for pin
+ */
+struct ipu_fw_isys_output_pin_info_abi {
+	struct ipu_fw_isys_resolution_abi output_res;
+	u32 stride;
+	u32 watermark_in_lines;
+	u32 payload_buf_size;
+	u32 ts_offsets[IPU_PIN_PLANES_MAX];
+	u32 s2m_pixel_soc_pixel_remapping;
+	u32 csi_be_soc_pixel_remapping;
+	u8 send_irq;
+	u8 input_pin_id;
+	u8 pt;
+	u8 ft;
+	u8 reserved;
+	u8 reserve_compression;
+	u8 snoopable;
+	u8 error_handling_enable;
+	u32 sensor_type;
+};
+
+/**
+ * struct ipu_fw_isys_param_pin_abi
+ * @param_buf_id: Points to param port buffer - buffer identifier
+ * @addr: Points to param pin buffer - CSS Virtual Address
+ */
+struct ipu_fw_isys_param_pin_abi {
+	u64 param_buf_id;
+	u32 addr;
+};
+
+/**
+ * struct ipu_fw_isys_input_pin_info_abi
+ * @input_res: input resolution
+ * @dt: mipi data type ((enum ipu_fw_isys_mipi_data_type)
+ * @mipi_store_mode: defines if legacy long packet header will be stored or
+ *		     discarded if discarded, output pin type for this
+ *		     input pin can only be MIPI
+ *		     (enum ipu_fw_isys_mipi_store_mode)
+ * @bits_per_pix: native bits per pixel
+ * @mapped_dt: actual data type from sensor
+ * @mipi_decompression: defines which compression will be in mipi backend
+
+ * @crop_first_and_last_lines    Control whether to crop the
+ *                              first and last line of the
+ *                              input image. Crop done by HW
+ *                              device.
+ * @capture_mode: mode of capture, regular or burst, default value is regular
+ */
+struct ipu_fw_isys_input_pin_info_abi {
+	struct ipu_fw_isys_resolution_abi input_res;
+	u8 dt;
+	u8 mipi_store_mode;
+	u8 bits_per_pix;
+	u8 mapped_dt;
+	u8 mipi_decompression;
+	u8 crop_first_and_last_lines;
+	u8 capture_mode;
+};
+
+/**
+ * struct ipu_fw_isys_cropping_abi - cropping coordinates
+ */
+struct ipu_fw_isys_cropping_abi {
+	s32 top_offset;
+	s32 left_offset;
+	s32 bottom_offset;
+	s32 right_offset;
+};
+
+/**
+ * struct ipu_fw_isys_stream_cfg_data_abi
+ * ISYS stream configuration data structure
+ * @crop: defines cropping resolution for the
+ * maximum number of input pins which can be cropped,
+ * it is directly mapped to the HW devices
+ * @input_pins: input pin descriptors
+ * @output_pins: output pin descriptors
+ * @compfmt: de-compression setting for User Defined Data
+ * @nof_input_pins: number of input pins
+ * @nof_output_pins: number of output pins
+ * @send_irq_sof_discarded: send irq on discarded frame sof response
+ *		- if '1' it will override the send_resp_sof_discarded
+ *		  and send the response
+ *		- if '0' the send_resp_sof_discarded will determine
+ *		  whether to send the response
+ * @send_irq_eof_discarded: send irq on discarded frame eof response
+ *		- if '1' it will override the send_resp_eof_discarded
+ *		  and send the response
+ *		- if '0' the send_resp_eof_discarded will determine
+ *		  whether to send the response
+ * @send_resp_sof_discarded: send response for discarded frame sof detected,
+ *			     used only when send_irq_sof_discarded is '0'
+ * @send_resp_eof_discarded: send response for discarded frame eof detected,
+ *			     used only when send_irq_eof_discarded is '0'
+ * @src: Stream source index e.g. MIPI_generator_0, CSI2-rx_1
+ * @vc: MIPI Virtual Channel (up to 4 virtual per physical channel)
+ * @isl_use: indicates whether stream requires ISL and how
+ * @sensor_type: type of connected sensor, tobii or others, default is 0
+ */
+struct ipu_fw_isys_stream_cfg_data_abi {
+	struct ipu_fw_isys_cropping_abi crop;
+	struct ipu_fw_isys_input_pin_info_abi input_pins[IPU_MAX_IPINS];
+	struct ipu_fw_isys_output_pin_info_abi output_pins[IPU_MAX_OPINS];
+	u32 compfmt;
+	u8 nof_input_pins;
+	u8 nof_output_pins;
+	u8 send_irq_sof_discarded;
+	u8 send_irq_eof_discarded;
+	u8 send_resp_sof_discarded;
+	u8 send_resp_eof_discarded;
+	u8 src;
+	u8 vc;
+	u8 isl_use;
+	u8 sensor_type;
+};
+
+/**
+ * struct ipu_fw_isys_frame_buff_set - frame buffer set
+ * @output_pins: output pin addresses
+ * @send_irq_sof: send irq on frame sof response
+ *		- if '1' it will override the send_resp_sof and
+ *		  send the response
+ *		- if '0' the send_resp_sof will determine whether to
+ *		  send the response
+ * @send_irq_eof: send irq on frame eof response
+ *		- if '1' it will override the send_resp_eof and
+ *		  send the response
+ *		- if '0' the send_resp_eof will determine whether to
+ *		  send the response
+ * @send_resp_sof: send response for frame sof detected,
+ *		   used only when send_irq_sof is '0'
+ * @send_resp_eof: send response for frame eof detected,
+ *		   used only when send_irq_eof is '0'
+ * @send_resp_capture_ack: send response for capture ack event
+ * @send_resp_capture_done: send response for capture done event
+ */
+struct ipu_fw_isys_frame_buff_set_abi {
+	struct ipu_fw_isys_output_pin_payload_abi output_pins[IPU_MAX_OPINS];
+	u8 send_irq_sof;
+	u8 send_irq_eof;
+	u8 send_irq_capture_ack;
+	u8 send_irq_capture_done;
+	u8 send_resp_sof;
+	u8 send_resp_eof;
+	u8 send_resp_capture_ack;
+	u8 send_resp_capture_done;
+	u8 reserved;
+};
+
+/**
+ * struct ipu_fw_isys_error_info_abi
+ * @error: error code if something went wrong
+ * @error_details: depending on error code, it may contain additional error info
+ */
+struct ipu_fw_isys_error_info_abi {
+	enum ipu_fw_isys_error error;
+	u32 error_details;
+};
+
+/**
+ * struct ipu_fw_isys_resp_info_comm
+ * @pin: this var is only valid for pin event related responses,
+ *     contains pin addresses
+ * @error_info: error information from the FW
+ * @timestamp: Time information for event if available
+ * @stream_handle: stream id the response corresponds to
+ * @type: response type (enum ipu_fw_isys_resp_type)
+ * @pin_id: pin id that the pin payload corresponds to
+ */
+struct ipu_fw_isys_resp_info_abi {
+	u64 buf_id;
+	struct ipu_fw_isys_output_pin_payload_abi pin;
+	struct ipu_fw_isys_error_info_abi error_info;
+	u32 timestamp[2];
+	u8 stream_handle;
+	u8 type;
+	u8 pin_id;
+	u16 reserved;
+};
+
+/**
+ * struct ipu_fw_isys_proxy_error_info_comm
+ * @proxy_error: error code if something went wrong
+ * @proxy_error_details: depending on error code, it may contain additional
+ *			error info
+ */
+struct ipu_fw_isys_proxy_error_info_abi {
+	enum ipu_fw_proxy_error error;
+	u32 error_details;
+};
+
+struct ipu_fw_isys_proxy_resp_info_abi {
+	u32 request_id;
+	struct ipu_fw_isys_proxy_error_info_abi error_info;
+};
+
+/**
+ * struct ipu_fw_proxy_write_queue_token
+ * @request_id: update id for the specific proxy write request
+ * @region_index: Region id for the proxy write request
+ * @offset: Offset of the write request according to the base address
+ *	    of the region
+ * @value: Value that is requested to be written with the proxy write request
+ */
+struct ipu_fw_proxy_write_queue_token {
+	u32 request_id;
+	u32 region_index;
+	u32 offset;
+	u32 value;
+};
+
+/* From here on type defines not coming from the ISYSAPI interface */
+
+/**
+ * struct ipu_fw_resp_queue_token
+ */
+struct ipu_fw_resp_queue_token {
+	struct ipu_fw_isys_resp_info_abi resp_info;
+};
+
+/**
+ * struct ipu_fw_send_queue_token
+ */
+struct ipu_fw_send_queue_token {
+	u64 buf_handle;
+	u32 payload;
+	u16 send_type;
+	u16 stream_id;
+};
+
+/**
+ * struct ipu_fw_proxy_resp_queue_token
+ */
+struct ipu_fw_proxy_resp_queue_token {
+	struct ipu_fw_isys_proxy_resp_info_abi proxy_resp_info;
+};
+
+/**
+ * struct ipu_fw_proxy_send_queue_token
+ */
+struct ipu_fw_proxy_send_queue_token {
+	u32 request_id;
+	u32 region_index;
+	u32 offset;
+	u32 value;
+};
+
+void ipu_fw_isys_set_params(struct ipu_fw_isys_stream_cfg_data_abi *stream_cfg);
+
+void ipu_fw_isys_dump_stream_cfg(struct device *dev,
+				 struct ipu_fw_isys_stream_cfg_data_abi
+				 *stream_cfg);
+void ipu_fw_isys_dump_frame_buff_set(struct device *dev,
+				     struct ipu_fw_isys_frame_buff_set_abi *buf,
+				     unsigned int outputs);
+int ipu_fw_isys_init(struct ipu_isys *isys, unsigned int num_streams);
+int ipu_fw_isys_close(struct ipu_isys *isys);
+int ipu_fw_isys_simple_cmd(struct ipu_isys *isys,
+			   const unsigned int stream_handle,
+			   enum ipu_fw_isys_send_type send_type);
+int ipu_fw_isys_complex_cmd(struct ipu_isys *isys,
+			    const unsigned int stream_handle,
+			    void *cpu_mapped_buf,
+			    dma_addr_t dma_mapped_buf,
+			    size_t size, enum ipu_fw_isys_send_type send_type);
+int ipu_fw_isys_send_proxy_token(struct ipu_isys *isys,
+				 unsigned int req_id,
+				 unsigned int index,
+				 unsigned int offset, u32 value);
+void ipu_fw_isys_cleanup(struct ipu_isys *isys);
+struct ipu_fw_isys_resp_info_abi *
+ipu_fw_isys_get_resp(void *context, unsigned int queue,
+		     struct ipu_fw_isys_resp_info_abi *response);
+void ipu_fw_isys_put_resp(void *context, unsigned int queue);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-fw-psys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-fw-psys.c
@@ -0,0 +1,430 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2016 - 2020 Intel Corporation
+
+#include <linux/delay.h>
+
+#include <uapi/linux/ipu-psys.h>
+
+#include "ipu-fw-com.h"
+#include "ipu-fw-psys.h"
+#include "ipu-psys.h"
+
+int ipu_fw_psys_pg_start(struct ipu_psys_kcmd *kcmd)
+{
+	kcmd->kpg->pg->state = IPU_FW_PSYS_PROCESS_GROUP_STARTED;
+	return 0;
+}
+
+int ipu_fw_psys_pg_disown(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_fw_psys_cmd *psys_cmd;
+	int ret = 0;
+
+	psys_cmd = ipu_send_get_token(kcmd->fh->psys->fwcom, 0);
+	if (!psys_cmd) {
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"%s failed to get token!\n", __func__);
+		kcmd->pg_user = NULL;
+		ret = -ENODATA;
+		goto out;
+	}
+	psys_cmd->command = IPU_FW_PSYS_PROCESS_GROUP_CMD_START;
+	psys_cmd->msg = 0;
+	psys_cmd->context_handle = kcmd->kpg->pg->ipu_virtual_address;
+	ipu_send_put_token(kcmd->fh->psys->fwcom, 0);
+
+out:
+	return ret;
+}
+
+int ipu_fw_psys_ppg_suspend(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_fw_psys_cmd *psys_cmd;
+	int ret = 0;
+
+	/* ppg suspend cmd uses QUEUE_DEVICE_ID instead of QUEUE_COMMAND_ID */
+	psys_cmd = ipu_send_get_token(kcmd->fh->psys->fwcom, 1);
+	if (!psys_cmd) {
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"%s failed to get token!\n", __func__);
+		kcmd->pg_user = NULL;
+		ret = -ENODATA;
+		goto out;
+	}
+	psys_cmd->command = IPU_FW_PSYS_PROCESS_GROUP_CMD_SUSPEND;
+	psys_cmd->msg = 0;
+	psys_cmd->context_handle = kcmd->kpg->pg->ipu_virtual_address;
+	ipu_send_put_token(kcmd->fh->psys->fwcom, 1);
+
+out:
+	return ret;
+}
+
+int ipu_fw_psys_ppg_resume(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_fw_psys_cmd *psys_cmd;
+	int ret = 0;
+
+	psys_cmd = ipu_send_get_token(kcmd->fh->psys->fwcom, 0);
+	if (!psys_cmd) {
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"%s failed to get token!\n", __func__);
+		kcmd->pg_user = NULL;
+		ret = -ENODATA;
+		goto out;
+	}
+	psys_cmd->command = IPU_FW_PSYS_PROCESS_GROUP_CMD_RESUME;
+	psys_cmd->msg = 0;
+	psys_cmd->context_handle = kcmd->kpg->pg->ipu_virtual_address;
+	ipu_send_put_token(kcmd->fh->psys->fwcom, 0);
+
+out:
+	return ret;
+}
+
+int ipu_fw_psys_pg_abort(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_fw_psys_cmd *psys_cmd;
+	int ret = 0;
+
+	psys_cmd = ipu_send_get_token(kcmd->fh->psys->fwcom, 0);
+	if (!psys_cmd) {
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"%s failed to get token!\n", __func__);
+		kcmd->pg_user = NULL;
+		ret = -ENODATA;
+		goto out;
+	}
+	psys_cmd->command = IPU_FW_PSYS_PROCESS_GROUP_CMD_STOP;
+	psys_cmd->msg = 0;
+	psys_cmd->context_handle = kcmd->kpg->pg->ipu_virtual_address;
+	ipu_send_put_token(kcmd->fh->psys->fwcom, 0);
+
+out:
+	return ret;
+}
+
+int ipu_fw_psys_pg_submit(struct ipu_psys_kcmd *kcmd)
+{
+	kcmd->kpg->pg->state = IPU_FW_PSYS_PROCESS_GROUP_BLOCKED;
+	return 0;
+}
+
+int ipu_fw_psys_rcv_event(struct ipu_psys *psys,
+			  struct ipu_fw_psys_event *event)
+{
+	void *rcv;
+
+	rcv = ipu_recv_get_token(psys->fwcom, 0);
+	if (!rcv)
+		return 0;
+
+	memcpy(event, rcv, sizeof(*event));
+	ipu_recv_put_token(psys->fwcom, 0);
+	return 1;
+}
+
+int ipu_fw_psys_terminal_set(struct ipu_fw_psys_terminal *terminal,
+			     int terminal_idx,
+			     struct ipu_psys_kcmd *kcmd,
+			     u32 buffer, unsigned int size)
+{
+	u32 type;
+	u32 buffer_state;
+
+	type = terminal->terminal_type;
+
+	switch (type) {
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_CACHED_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_CACHED_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SPATIAL_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SPATIAL_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SLICED_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SLICED_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PROGRAM:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PROGRAM_CONTROL_INIT:
+		buffer_state = IPU_FW_PSYS_BUFFER_UNDEFINED;
+		break;
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_STREAM:
+	case IPU_FW_PSYS_TERMINAL_TYPE_DATA_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_STATE_IN:
+		buffer_state = IPU_FW_PSYS_BUFFER_FULL;
+		break;
+	case IPU_FW_PSYS_TERMINAL_TYPE_DATA_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_STATE_OUT:
+		buffer_state = IPU_FW_PSYS_BUFFER_EMPTY;
+		break;
+	default:
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"unknown terminal type: 0x%x\n", type);
+		return -EAGAIN;
+	}
+
+	if (type == IPU_FW_PSYS_TERMINAL_TYPE_DATA_IN ||
+	    type == IPU_FW_PSYS_TERMINAL_TYPE_DATA_OUT) {
+		struct ipu_fw_psys_data_terminal *dterminal =
+		    (struct ipu_fw_psys_data_terminal *)terminal;
+		dterminal->connection_type = IPU_FW_PSYS_CONNECTION_MEMORY;
+		dterminal->frame.data_bytes = size;
+		if (!ipu_fw_psys_pg_get_protocol(kcmd))
+			dterminal->frame.data = buffer;
+		else
+			dterminal->frame.data_index = terminal_idx;
+		dterminal->frame.buffer_state = buffer_state;
+	} else {
+		struct ipu_fw_psys_param_terminal *pterminal =
+		    (struct ipu_fw_psys_param_terminal *)terminal;
+		if (!ipu_fw_psys_pg_get_protocol(kcmd))
+			pterminal->param_payload.buffer = buffer;
+		else
+			pterminal->param_payload.terminal_index = terminal_idx;
+	}
+	return 0;
+}
+
+void ipu_fw_psys_pg_dump(struct ipu_psys *psys,
+			 struct ipu_psys_kcmd *kcmd, const char *note)
+{
+	ipu6_fw_psys_pg_dump(psys, kcmd, note);
+}
+
+int ipu_fw_psys_pg_get_id(struct ipu_psys_kcmd *kcmd)
+{
+	return kcmd->kpg->pg->ID;
+}
+
+int ipu_fw_psys_pg_get_terminal_count(struct ipu_psys_kcmd *kcmd)
+{
+	return kcmd->kpg->pg->terminal_count;
+}
+
+int ipu_fw_psys_pg_get_size(struct ipu_psys_kcmd *kcmd)
+{
+	return kcmd->kpg->pg->size;
+}
+
+int ipu_fw_psys_pg_set_ipu_vaddress(struct ipu_psys_kcmd *kcmd,
+				    dma_addr_t vaddress)
+{
+	kcmd->kpg->pg->ipu_virtual_address = vaddress;
+	return 0;
+}
+
+struct ipu_fw_psys_terminal *ipu_fw_psys_pg_get_terminal(struct ipu_psys_kcmd
+							 *kcmd, int index)
+{
+	struct ipu_fw_psys_terminal *terminal;
+	u16 *terminal_offset_table;
+
+	terminal_offset_table =
+	    (uint16_t *)((char *)kcmd->kpg->pg +
+			  kcmd->kpg->pg->terminals_offset);
+	terminal = (struct ipu_fw_psys_terminal *)
+	    ((char *)kcmd->kpg->pg + terminal_offset_table[index]);
+	return terminal;
+}
+
+void ipu_fw_psys_pg_set_token(struct ipu_psys_kcmd *kcmd, u64 token)
+{
+	kcmd->kpg->pg->token = (u64)token;
+}
+
+u64 ipu_fw_psys_pg_get_token(struct ipu_psys_kcmd *kcmd)
+{
+	return kcmd->kpg->pg->token;
+}
+
+int ipu_fw_psys_pg_get_protocol(struct ipu_psys_kcmd *kcmd)
+{
+	return kcmd->kpg->pg->protocol_version;
+}
+
+int ipu_fw_psys_ppg_set_buffer_set(struct ipu_psys_kcmd *kcmd,
+				   struct ipu_fw_psys_terminal *terminal,
+				   int terminal_idx, u32 buffer)
+{
+	u32 type;
+	u32 buffer_state;
+	u32 *buffer_ptr;
+	struct ipu_fw_psys_buffer_set *buf_set = kcmd->kbuf_set->buf_set;
+
+	type = terminal->terminal_type;
+
+	switch (type) {
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_CACHED_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_CACHED_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SPATIAL_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SPATIAL_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SLICED_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SLICED_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PROGRAM:
+	case IPU_FW_PSYS_TERMINAL_TYPE_PROGRAM_CONTROL_INIT:
+		buffer_state = IPU_FW_PSYS_BUFFER_UNDEFINED;
+		break;
+	case IPU_FW_PSYS_TERMINAL_TYPE_PARAM_STREAM:
+	case IPU_FW_PSYS_TERMINAL_TYPE_DATA_IN:
+	case IPU_FW_PSYS_TERMINAL_TYPE_STATE_IN:
+		buffer_state = IPU_FW_PSYS_BUFFER_FULL;
+		break;
+	case IPU_FW_PSYS_TERMINAL_TYPE_DATA_OUT:
+	case IPU_FW_PSYS_TERMINAL_TYPE_STATE_OUT:
+		buffer_state = IPU_FW_PSYS_BUFFER_EMPTY;
+		break;
+	default:
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"unknown terminal type: 0x%x\n", type);
+		return -EAGAIN;
+	}
+
+	buffer_ptr = (u32 *)((char *)buf_set + sizeof(*buf_set) +
+			      terminal_idx * sizeof(*buffer_ptr));
+
+	*buffer_ptr = buffer;
+
+	if (type == IPU_FW_PSYS_TERMINAL_TYPE_DATA_IN ||
+	    type == IPU_FW_PSYS_TERMINAL_TYPE_DATA_OUT) {
+		struct ipu_fw_psys_data_terminal *dterminal =
+		    (struct ipu_fw_psys_data_terminal *)terminal;
+		dterminal->frame.buffer_state = buffer_state;
+	}
+
+	return 0;
+}
+
+size_t ipu_fw_psys_ppg_get_buffer_set_size(struct ipu_psys_kcmd *kcmd)
+{
+	return (sizeof(struct ipu_fw_psys_buffer_set) +
+		kcmd->kpg->pg->terminal_count * sizeof(u32));
+}
+
+int
+ipu_fw_psys_ppg_buffer_set_vaddress(struct ipu_fw_psys_buffer_set *buf_set,
+				    u32 vaddress)
+{
+	buf_set->ipu_virtual_address = vaddress;
+	return 0;
+}
+
+int ipu_fw_psys_ppg_buffer_set_set_kernel_enable_bitmap(
+		struct ipu_fw_psys_buffer_set *buf_set,
+		u32 *kernel_enable_bitmap)
+{
+	memcpy(buf_set->kernel_enable_bitmap, (u8 *)kernel_enable_bitmap,
+	       sizeof(buf_set->kernel_enable_bitmap));
+	return 0;
+}
+
+struct ipu_fw_psys_buffer_set *
+ipu_fw_psys_ppg_create_buffer_set(struct ipu_psys_kcmd *kcmd,
+				  void *kaddr, u32 frame_counter)
+{
+	struct ipu_fw_psys_buffer_set *buffer_set = NULL;
+	unsigned int i;
+
+	buffer_set = (struct ipu_fw_psys_buffer_set *)kaddr;
+
+	/*
+	 * Set base struct members
+	 */
+	buffer_set->ipu_virtual_address = 0;
+	buffer_set->process_group_handle = kcmd->kpg->pg->ipu_virtual_address;
+	buffer_set->frame_counter = frame_counter;
+	buffer_set->terminal_count = kcmd->kpg->pg->terminal_count;
+
+	/*
+	 * Initialize adjacent buffer addresses
+	 */
+	for (i = 0; i < buffer_set->terminal_count; i++) {
+		u32 *buffer =
+		    (u32 *)((char *)buffer_set +
+			     sizeof(*buffer_set) + sizeof(u32) * i);
+
+		*buffer = 0;
+	}
+
+	return buffer_set;
+}
+
+int ipu_fw_psys_ppg_enqueue_bufs(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_fw_psys_cmd *psys_cmd;
+	unsigned int queue_id;
+	int ret = 0;
+	unsigned int size;
+
+	if (ipu_ver == IPU_VER_6SE)
+		size = IPU6SE_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+	else
+		size = IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+	queue_id = kcmd->kpg->pg->base_queue_id;
+
+	if (queue_id >= size)
+		return -EINVAL;
+
+	psys_cmd = ipu_send_get_token(kcmd->fh->psys->fwcom, queue_id);
+	if (!psys_cmd) {
+		dev_err(&kcmd->fh->psys->adev->dev,
+			"%s failed to get token!\n", __func__);
+		kcmd->pg_user = NULL;
+		return -ENODATA;
+	}
+
+	psys_cmd->command = IPU_FW_PSYS_PROCESS_GROUP_CMD_RUN;
+	psys_cmd->msg = 0;
+	psys_cmd->context_handle = kcmd->kbuf_set->buf_set->ipu_virtual_address;
+
+	ipu_send_put_token(kcmd->fh->psys->fwcom, queue_id);
+
+	return ret;
+}
+
+u8 ipu_fw_psys_ppg_get_base_queue_id(struct ipu_psys_kcmd *kcmd)
+{
+	return kcmd->kpg->pg->base_queue_id;
+}
+
+void ipu_fw_psys_ppg_set_base_queue_id(struct ipu_psys_kcmd *kcmd, u8 queue_id)
+{
+	kcmd->kpg->pg->base_queue_id = queue_id;
+}
+
+int ipu_fw_psys_open(struct ipu_psys *psys)
+{
+	int retry = IPU_PSYS_OPEN_RETRY, retval;
+
+	retval = ipu_fw_com_open(psys->fwcom);
+	if (retval) {
+		dev_err(&psys->adev->dev, "fw com open failed.\n");
+		return retval;
+	}
+
+	do {
+		usleep_range(IPU_PSYS_OPEN_TIMEOUT_US,
+			     IPU_PSYS_OPEN_TIMEOUT_US + 10);
+		retval = ipu_fw_com_ready(psys->fwcom);
+		if (!retval) {
+			dev_dbg(&psys->adev->dev, "psys port open ready!\n");
+			break;
+		}
+	} while (retry-- > 0);
+
+	if (!retry && retval) {
+		dev_err(&psys->adev->dev, "psys port open ready failed %d\n",
+			retval);
+		ipu_fw_com_close(psys->fwcom);
+		return retval;
+	}
+	return 0;
+}
+
+int ipu_fw_psys_close(struct ipu_psys *psys)
+{
+	int retval;
+
+	retval = ipu_fw_com_close(psys->fwcom);
+	if (retval) {
+		dev_err(&psys->adev->dev, "fw com close failed.\n");
+		return retval;
+	}
+	return retval;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-fw-psys.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-fw-psys.h
@@ -0,0 +1,382 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2016 - 2020 Intel Corporation */
+
+#ifndef IPU_FW_PSYS_H
+#define IPU_FW_PSYS_H
+
+#include "ipu6-platform-resources.h"
+#include "ipu6se-platform-resources.h"
+#include "ipu6ep-platform-resources.h"
+
+#define IPU_FW_PSYS_CMD_QUEUE_SIZE 0x20
+#define IPU_FW_PSYS_EVENT_QUEUE_SIZE 0x40
+
+#define IPU_FW_PSYS_CMD_BITS 64
+#define IPU_FW_PSYS_EVENT_BITS 128
+
+enum {
+	IPU_FW_PSYS_EVENT_TYPE_SUCCESS = 0,
+	IPU_FW_PSYS_EVENT_TYPE_UNKNOWN_ERROR = 1,
+	IPU_FW_PSYS_EVENT_TYPE_RET_REM_OBJ_NOT_FOUND = 2,
+	IPU_FW_PSYS_EVENT_TYPE_RET_REM_OBJ_TOO_BIG = 3,
+	IPU_FW_PSYS_EVENT_TYPE_RET_REM_OBJ_DDR_TRANS_ERR = 4,
+	IPU_FW_PSYS_EVENT_TYPE_RET_REM_OBJ_NULL_PKG_DIR_ADDR = 5,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_LOAD_FRAME_ERR = 6,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_LOAD_FRAGMENT_ERR = 7,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_PROCESS_COUNT_ZERO = 8,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_PROCESS_INIT_ERR = 9,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_ABORT = 10,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_NULL = 11,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_VALIDATION_ERR = 12,
+	IPU_FW_PSYS_EVENT_TYPE_PROC_GRP_INVALID_FRAME = 13
+};
+
+enum {
+	IPU_FW_PSYS_EVENT_QUEUE_MAIN_ID,
+	IPU_FW_PSYS_N_PSYS_EVENT_QUEUE_ID
+};
+
+enum {
+	IPU_FW_PSYS_PROCESS_GROUP_ERROR = 0,
+	IPU_FW_PSYS_PROCESS_GROUP_CREATED,
+	IPU_FW_PSYS_PROCESS_GROUP_READY,
+	IPU_FW_PSYS_PROCESS_GROUP_BLOCKED,
+	IPU_FW_PSYS_PROCESS_GROUP_STARTED,
+	IPU_FW_PSYS_PROCESS_GROUP_RUNNING,
+	IPU_FW_PSYS_PROCESS_GROUP_STALLED,
+	IPU_FW_PSYS_PROCESS_GROUP_STOPPED,
+	IPU_FW_PSYS_N_PROCESS_GROUP_STATES
+};
+
+enum {
+	IPU_FW_PSYS_CONNECTION_MEMORY = 0,
+	IPU_FW_PSYS_CONNECTION_MEMORY_STREAM,
+	IPU_FW_PSYS_CONNECTION_STREAM,
+	IPU_FW_PSYS_N_CONNECTION_TYPES
+};
+
+enum {
+	IPU_FW_PSYS_BUFFER_NULL = 0,
+	IPU_FW_PSYS_BUFFER_UNDEFINED,
+	IPU_FW_PSYS_BUFFER_EMPTY,
+	IPU_FW_PSYS_BUFFER_NONEMPTY,
+	IPU_FW_PSYS_BUFFER_FULL,
+	IPU_FW_PSYS_N_BUFFER_STATES
+};
+
+enum {
+	IPU_FW_PSYS_TERMINAL_TYPE_DATA_IN = 0,
+	IPU_FW_PSYS_TERMINAL_TYPE_DATA_OUT,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_STREAM,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_CACHED_IN,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_CACHED_OUT,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SPATIAL_IN,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SPATIAL_OUT,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SLICED_IN,
+	IPU_FW_PSYS_TERMINAL_TYPE_PARAM_SLICED_OUT,
+	IPU_FW_PSYS_TERMINAL_TYPE_STATE_IN,
+	IPU_FW_PSYS_TERMINAL_TYPE_STATE_OUT,
+	IPU_FW_PSYS_TERMINAL_TYPE_PROGRAM,
+	IPU_FW_PSYS_TERMINAL_TYPE_PROGRAM_CONTROL_INIT,
+	IPU_FW_PSYS_N_TERMINAL_TYPES
+};
+
+enum {
+	IPU_FW_PSYS_COL_DIMENSION = 0,
+	IPU_FW_PSYS_ROW_DIMENSION = 1,
+	IPU_FW_PSYS_N_DATA_DIMENSION = 2
+};
+
+enum {
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_NOP = 0,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_SUBMIT,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_ATTACH,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_DETACH,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_START,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_DISOWN,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_RUN,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_STOP,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_SUSPEND,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_RESUME,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_ABORT,
+	IPU_FW_PSYS_PROCESS_GROUP_CMD_RESET,
+	IPU_FW_PSYS_N_PROCESS_GROUP_CMDS
+};
+
+enum {
+	IPU_FW_PSYS_PROCESS_GROUP_PROTOCOL_LEGACY = 0,
+	IPU_FW_PSYS_PROCESS_GROUP_PROTOCOL_PPG,
+	IPU_FW_PSYS_PROCESS_GROUP_N_PROTOCOLS
+};
+
+struct __packed ipu_fw_psys_process_group {
+	u64 token;
+	u64 private_token;
+	u32 routing_bitmap[IPU_FW_PSYS_RBM_NOF_ELEMS];
+	u32 kernel_bitmap[IPU_FW_PSYS_KBM_NOF_ELEMS];
+	u32 size;
+	u32 psys_server_init_cycles;
+	u32 pg_load_start_ts;
+	u32 pg_load_cycles;
+	u32 pg_init_cycles;
+	u32 pg_processing_cycles;
+	u32 pg_next_frame_init_cycles;
+	u32 pg_complete_cycles;
+	u32 ID;
+	u32 state;
+	u32 ipu_virtual_address;
+	u32 resource_bitmap;
+	u16 fragment_count;
+	u16 fragment_state;
+	u16 fragment_limit;
+	u16 processes_offset;
+	u16 terminals_offset;
+	u8 process_count;
+	u8 terminal_count;
+	u8 subgraph_count;
+	u8 protocol_version;
+	u8 base_queue_id;
+	u8 num_queues;
+	u8 mask_irq;
+	u8 error_handling_enable;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_PROCESS_GROUP_STRUCT];
+};
+
+struct ipu_fw_psys_srv_init {
+	void *host_ddr_pkg_dir;
+	u32 ddr_pkg_dir_address;
+	u32 pkg_dir_size;
+
+	u32 icache_prefetch_sp;
+	u32 icache_prefetch_isp;
+};
+
+struct __packed ipu_fw_psys_cmd {
+	u16 command;
+	u16 msg;
+	u32 context_handle;
+};
+
+struct __packed ipu_fw_psys_event {
+	u16 status;
+	u16 command;
+	u32 context_handle;
+	u64 token;
+};
+
+struct ipu_fw_psys_terminal {
+	u32 terminal_type;
+	s16 parent_offset;
+	u16 size;
+	u16 tm_index;
+	u8 ID;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_TERMINAL_STRUCT];
+};
+
+struct ipu_fw_psys_param_payload {
+	u64 host_buffer;
+	u32 buffer;
+	u32 terminal_index;
+};
+
+struct ipu_fw_psys_param_terminal {
+	struct ipu_fw_psys_terminal base;
+	struct ipu_fw_psys_param_payload param_payload;
+	u16 param_section_desc_offset;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_PARAM_TERMINAL_STRUCT];
+};
+
+struct ipu_fw_psys_frame {
+	u32 buffer_state;
+	u32 access_type;
+	u32 pointer_state;
+	u32 access_scope;
+	u32 data;
+	u32 data_index;
+	u32 data_bytes;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_FRAME_STRUCT];
+};
+
+struct ipu_fw_psys_frame_descriptor {
+	u32 frame_format_type;
+	u32 plane_count;
+	u32 plane_offsets[IPU_FW_PSYS_N_FRAME_PLANES];
+	u32 stride[1];
+	u32 ts_offsets[IPU_FW_PSYS_N_FRAME_PLANES];
+	u16 dimension[2];
+	u16 size;
+	u8 bpp;
+	u8 bpe;
+	u8 is_compressed;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_FRAME_DESC_STRUCT];
+};
+
+struct ipu_fw_psys_stream {
+	u64 dummy;
+};
+
+struct ipu_fw_psys_data_terminal {
+	struct ipu_fw_psys_terminal base;
+	struct ipu_fw_psys_frame_descriptor frame_descriptor;
+	struct ipu_fw_psys_frame frame;
+	struct ipu_fw_psys_stream stream;
+	u32 reserved;
+	u32 connection_type;
+	u16 fragment_descriptor_offset;
+	u8 kernel_id;
+	u8 subgraph_id;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_DATA_TERMINAL_STRUCT];
+};
+
+struct ipu_fw_psys_buffer_set {
+	u64 token;
+	u32 kernel_enable_bitmap[IPU_FW_PSYS_KERNEL_BITMAP_NOF_ELEMS];
+	u32 terminal_enable_bitmap[IPU_FW_PSYS_KERNEL_BITMAP_NOF_ELEMS];
+	u32 routing_enable_bitmap[IPU_FW_PSYS_KERNEL_BITMAP_NOF_ELEMS];
+	u32 rbm[IPU_FW_PSYS_RBM_NOF_ELEMS];
+	u32 ipu_virtual_address;
+	u32 process_group_handle;
+	u16 terminal_count;
+	u8 frame_counter;
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_BUFFER_SET_STRUCT];
+};
+
+struct ipu_fw_psys_program_group_manifest {
+	u32 kernel_bitmap[IPU_FW_PSYS_KERNEL_BITMAP_NOF_ELEMS];
+	u32 ID;
+	u16 program_manifest_offset;
+	u16 terminal_manifest_offset;
+	u16 private_data_offset;
+	u16 rbm_manifest_offset;
+	u16 size;
+	u8 alignment;
+	u8 kernel_count;
+	u8 program_count;
+	u8 terminal_count;
+	u8 subgraph_count;
+	u8 reserved[5];
+};
+
+struct ipu_fw_generic_program_manifest {
+	u16 *dev_chn_size;
+	u16 *dev_chn_offset;
+	u16 *ext_mem_size;
+	u16 *ext_mem_offset;
+	u8 cell_id;
+	u8 cells[IPU_FW_PSYS_PROCESS_MAX_CELLS];
+	u8 cell_type_id;
+	u8 *is_dfm_relocatable;
+	u32 *dfm_port_bitmap;
+	u32 *dfm_active_port_bitmap;
+};
+
+struct ipu_fw_resource_definitions {
+	u32 num_cells;
+	u32 num_cells_type;
+	const u8 *cells;
+	u32 num_dev_channels;
+	const u16 *dev_channels;
+
+	u32 num_ext_mem_types;
+	u32 num_ext_mem_ids;
+	const u16 *ext_mem_ids;
+
+	u32 num_dfm_ids;
+	const u16 *dfms;
+
+	u32 cell_mem_row;
+	const u8 *cell_mem;
+};
+
+struct ipu6_psys_hw_res_variant {
+	unsigned int queue_num;
+	unsigned int cell_num;
+	int (*set_proc_dev_chn)(struct ipu_fw_psys_process *ptr, u16 offset,
+				u16 value);
+	int (*set_proc_dfm_bitmap)(struct ipu_fw_psys_process *ptr,
+				   u16 id, u32 bitmap, u32 active_bitmap);
+	int (*set_proc_ext_mem)(struct ipu_fw_psys_process *ptr,
+				u16 type_id, u16 mem_id, u16 offset);
+	int (*get_pgm_by_proc)(struct ipu_fw_generic_program_manifest *gen_pm,
+			       const struct ipu_fw_psys_program_group_manifest
+			       *pg_manifest,
+			       struct ipu_fw_psys_process *process);
+};
+struct ipu_psys_kcmd;
+struct ipu_psys;
+int ipu_fw_psys_pg_start(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_disown(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_abort(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_submit(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_ppg_suspend(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_ppg_resume(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_load_cycles(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_init_cycles(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_processing_cycles(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_server_init_cycles(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_next_frame_init_cycles(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_complete_cycles(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_rcv_event(struct ipu_psys *psys,
+			  struct ipu_fw_psys_event *event);
+int ipu_fw_psys_terminal_set(struct ipu_fw_psys_terminal *terminal,
+			     int terminal_idx,
+			     struct ipu_psys_kcmd *kcmd,
+			     u32 buffer, unsigned int size);
+void ipu_fw_psys_pg_dump(struct ipu_psys *psys,
+			 struct ipu_psys_kcmd *kcmd, const char *note);
+int ipu_fw_psys_pg_get_id(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_get_terminal_count(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_get_size(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_pg_set_ipu_vaddress(struct ipu_psys_kcmd *kcmd,
+				    dma_addr_t vaddress);
+struct ipu_fw_psys_terminal *ipu_fw_psys_pg_get_terminal(struct ipu_psys_kcmd
+							 *kcmd, int index);
+void ipu_fw_psys_pg_set_token(struct ipu_psys_kcmd *kcmd, u64 token);
+u64 ipu_fw_psys_pg_get_token(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_ppg_set_buffer_set(struct ipu_psys_kcmd *kcmd,
+				   struct ipu_fw_psys_terminal *terminal,
+				   int terminal_idx, u32 buffer);
+size_t ipu_fw_psys_ppg_get_buffer_set_size(struct ipu_psys_kcmd *kcmd);
+int
+ipu_fw_psys_ppg_buffer_set_vaddress(struct ipu_fw_psys_buffer_set *buf_set,
+				    u32 vaddress);
+int ipu_fw_psys_ppg_buffer_set_set_kernel_enable_bitmap(
+	struct ipu_fw_psys_buffer_set *buf_set, u32 *kernel_enable_bitmap);
+struct ipu_fw_psys_buffer_set *
+ipu_fw_psys_ppg_create_buffer_set(struct ipu_psys_kcmd *kcmd,
+				  void *kaddr, u32 frame_counter);
+int ipu_fw_psys_ppg_enqueue_bufs(struct ipu_psys_kcmd *kcmd);
+u8 ipu_fw_psys_ppg_get_base_queue_id(struct ipu_psys_kcmd *kcmd);
+void ipu_fw_psys_ppg_set_base_queue_id(struct ipu_psys_kcmd *kcmd, u8 queue_id);
+int ipu_fw_psys_pg_get_protocol(struct ipu_psys_kcmd *kcmd);
+int ipu_fw_psys_open(struct ipu_psys *psys);
+int ipu_fw_psys_close(struct ipu_psys *psys);
+
+/* common resource interface for both abi and api mode */
+int ipu_fw_psys_set_process_cell_id(struct ipu_fw_psys_process *ptr, u8 index,
+				    u8 value);
+u8 ipu_fw_psys_get_process_cell_id(struct ipu_fw_psys_process *ptr, u8 index);
+int ipu_fw_psys_clear_process_cell(struct ipu_fw_psys_process *ptr);
+int ipu_fw_psys_set_proc_dev_chn(struct ipu_fw_psys_process *ptr, u16 offset,
+				 u16 value);
+int ipu_fw_psys_set_process_ext_mem(struct ipu_fw_psys_process *ptr,
+				    u16 type_id, u16 mem_id, u16 offset);
+int ipu_fw_psys_get_program_manifest_by_process(
+	struct ipu_fw_generic_program_manifest *gen_pm,
+	const struct ipu_fw_psys_program_group_manifest *pg_manifest,
+	struct ipu_fw_psys_process *process);
+int ipu6_fw_psys_set_proc_dev_chn(struct ipu_fw_psys_process *ptr, u16 offset,
+				  u16 value);
+int ipu6_fw_psys_set_proc_dfm_bitmap(struct ipu_fw_psys_process *ptr,
+				     u16 id, u32 bitmap,
+				     u32 active_bitmap);
+int ipu6_fw_psys_set_process_ext_mem(struct ipu_fw_psys_process *ptr,
+				     u16 type_id, u16 mem_id, u16 offset);
+int ipu6_fw_psys_get_program_manifest_by_process(
+	struct ipu_fw_generic_program_manifest *gen_pm,
+	const struct ipu_fw_psys_program_group_manifest *pg_manifest,
+	struct ipu_fw_psys_process *process);
+void ipu6_fw_psys_pg_dump(struct ipu_psys *psys,
+			  struct ipu_psys_kcmd *kcmd, const char *note);
+void ipu6_psys_hw_res_variant_init(void);
+#endif /* IPU_FW_PSYS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-csi2-be-soc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-csi2-be-soc.c
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2014 - 2021 Intel Corporation
+
+#include <linux/device.h>
+#include <linux/module.h>
+
+#include <media/ipu-isys.h>
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-isys.h"
+#include "ipu-isys-csi2-be.h"
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-video.h"
+
+/*
+ * Raw bayer format pixel order MUST BE MAINTAINED in groups of four codes.
+ * Otherwise pixel order calculation below WILL BREAK!
+ */
+static const u32 csi2_be_soc_supported_codes_pad[] = {
+	MEDIA_BUS_FMT_Y10_1X10,
+	MEDIA_BUS_FMT_RGB565_1X16,
+	MEDIA_BUS_FMT_RGB888_1X24,
+	MEDIA_BUS_FMT_UYVY8_1X16,
+	MEDIA_BUS_FMT_YUYV8_1X16,
+	MEDIA_BUS_FMT_SBGGR12_1X12,
+	MEDIA_BUS_FMT_SGBRG12_1X12,
+	MEDIA_BUS_FMT_SGRBG12_1X12,
+	MEDIA_BUS_FMT_SRGGB12_1X12,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	0,
+};
+
+/*
+ * Raw bayer format pixel order MUST BE MAINTAINED in groups of four codes.
+ * Otherwise pixel order calculation below WILL BREAK!
+ */
+static const u32 csi2_be_soc_supported_raw_bayer_codes_pad[] = {
+	MEDIA_BUS_FMT_SBGGR12_1X12,
+	MEDIA_BUS_FMT_SGBRG12_1X12,
+	MEDIA_BUS_FMT_SGRBG12_1X12,
+	MEDIA_BUS_FMT_SRGGB12_1X12,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	0,
+};
+
+static int get_supported_code_index(u32 code)
+{
+	int i;
+
+	for (i = 0; csi2_be_soc_supported_raw_bayer_codes_pad[i]; i++) {
+		if (csi2_be_soc_supported_raw_bayer_codes_pad[i] == code)
+			return i;
+	}
+	return -EINVAL;
+}
+
+static const u32 *csi2_be_soc_supported_codes[NR_OF_CSI2_BE_SOC_PADS];
+
+static struct v4l2_subdev_internal_ops csi2_be_soc_sd_internal_ops = {
+	.open = ipu_isys_subdev_open,
+	.close = ipu_isys_subdev_close,
+};
+
+static const struct v4l2_subdev_core_ops csi2_be_soc_sd_core_ops = {
+};
+
+static const struct v4l2_ctrl_config compression_ctrl_cfg = {
+	.ops = NULL,
+	.id = V4L2_CID_IPU_ISYS_COMPRESSION,
+	.name = "ISYS BE-SOC compression",
+	.type = V4L2_CTRL_TYPE_BOOLEAN,
+	.min = 0,
+	.max = 1,
+	.step = 1,
+	.def = 0,
+};
+
+static int set_stream(struct v4l2_subdev *sd, int enable)
+{
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops csi2_be_soc_sd_video_ops = {
+	.s_stream = set_stream,
+};
+
+static int
+__subdev_link_validate(struct v4l2_subdev *sd, struct media_link *link,
+		       struct v4l2_subdev_format *source_fmt,
+		       struct v4l2_subdev_format *sink_fmt)
+{
+	struct ipu_isys_pipeline *ip = container_of(sd->entity.pipe,
+						    struct ipu_isys_pipeline,
+						    pipe);
+
+	ip->csi2_be_soc = to_ipu_isys_csi2_be_soc(sd);
+	return ipu_isys_subdev_link_validate(sd, link, source_fmt, sink_fmt);
+}
+
+static int
+ipu_isys_csi2_be_soc_set_sel(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_selection *sel)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	struct media_pad *pad = &asd->sd.entity.pads[sel->pad];
+
+	if (sel->target == V4L2_SEL_TGT_CROP &&
+	    pad->flags & MEDIA_PAD_FL_SOURCE &&
+	    asd->valid_tgts[sel->pad].crop) {
+		enum isys_subdev_prop_tgt tgt =
+		    IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_CROP;
+		struct v4l2_mbus_framefmt *ffmt =
+			__ipu_isys_get_ffmt(sd, sd_state, sel->pad, sel->which);
+
+		if (get_supported_code_index(ffmt->code) < 0) {
+			/* Non-bayer formats can't be odd lines cropped */
+			sel->r.left &= ~1;
+			sel->r.top &= ~1;
+		}
+
+		sel->r.width = clamp(sel->r.width, IPU_ISYS_MIN_WIDTH,
+				     IPU_ISYS_MAX_WIDTH);
+
+		sel->r.height = clamp(sel->r.height, IPU_ISYS_MIN_HEIGHT,
+				      IPU_ISYS_MAX_HEIGHT);
+
+		*__ipu_isys_get_selection(sd, sd_state, sel->target, sel->pad,
+					  sel->which) = sel->r;
+		ipu_isys_subdev_fmt_propagate(sd, sd_state, NULL, &sel->r,
+					      tgt, sel->pad, sel->which);
+		return 0;
+	}
+	return -EINVAL;
+}
+
+static const struct v4l2_subdev_pad_ops csi2_be_soc_sd_pad_ops = {
+	.link_validate = __subdev_link_validate,
+	.get_fmt = ipu_isys_subdev_get_ffmt,
+	.set_fmt = ipu_isys_subdev_set_ffmt,
+	.get_selection = ipu_isys_subdev_get_sel,
+	.set_selection = ipu_isys_csi2_be_soc_set_sel,
+	.enum_mbus_code = ipu_isys_subdev_enum_mbus_code,
+};
+
+static struct v4l2_subdev_ops csi2_be_soc_sd_ops = {
+	.core = &csi2_be_soc_sd_core_ops,
+	.video = &csi2_be_soc_sd_video_ops,
+	.pad = &csi2_be_soc_sd_pad_ops,
+};
+
+static struct media_entity_operations csi2_be_soc_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static void csi2_be_soc_set_ffmt(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct v4l2_mbus_framefmt *ffmt =
+		__ipu_isys_get_ffmt(sd, sd_state, fmt->pad,
+				    fmt->which);
+
+	if (sd->entity.pads[fmt->pad].flags & MEDIA_PAD_FL_SINK) {
+		if (fmt->format.field != V4L2_FIELD_ALTERNATE)
+			fmt->format.field = V4L2_FIELD_NONE;
+		*ffmt = fmt->format;
+
+		ipu_isys_subdev_fmt_propagate(sd, sd_state, &fmt->format,
+					      NULL,
+					      IPU_ISYS_SUBDEV_PROP_TGT_SINK_FMT,
+					      fmt->pad, fmt->which);
+	} else if (sd->entity.pads[fmt->pad].flags & MEDIA_PAD_FL_SOURCE) {
+		struct v4l2_mbus_framefmt *sink_ffmt;
+		struct v4l2_rect *r = __ipu_isys_get_selection(sd, sd_state,
+			V4L2_SEL_TGT_CROP, fmt->pad, fmt->which);
+		struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+		u32 code;
+		int idx;
+
+		sink_ffmt = __ipu_isys_get_ffmt(sd, sd_state, 0, fmt->which);
+		code = sink_ffmt->code;
+		idx = get_supported_code_index(code);
+
+		if (asd->valid_tgts[fmt->pad].crop && idx >= 0) {
+			int crop_info = 0;
+
+			/* Only croping odd line at top side. */
+			if (r->top & 1)
+				crop_info |= CSI2_BE_CROP_VER;
+
+			code = csi2_be_soc_supported_raw_bayer_codes_pad
+				[((idx & CSI2_BE_CROP_MASK) ^ crop_info)
+				+ (idx & ~CSI2_BE_CROP_MASK)];
+
+		}
+		ffmt->code = code;
+		ffmt->width = r->width;
+		ffmt->height = r->height;
+		ffmt->field = sink_ffmt->field;
+
+	}
+}
+
+void ipu_isys_csi2_be_soc_cleanup(struct ipu_isys_csi2_be_soc *csi2_be_soc)
+{
+	v4l2_device_unregister_subdev(&csi2_be_soc->asd.sd);
+	ipu_isys_subdev_cleanup(&csi2_be_soc->asd);
+	v4l2_ctrl_handler_free(&csi2_be_soc->av.ctrl_handler);
+	ipu_isys_video_cleanup(&csi2_be_soc->av);
+}
+
+int ipu_isys_csi2_be_soc_init(struct ipu_isys_csi2_be_soc *csi2_be_soc,
+			      struct ipu_isys *isys, int index)
+{
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.pad = CSI2_BE_SOC_PAD_SINK,
+		.format = {
+			   .width = 4096,
+			   .height = 3072,
+			   },
+	};
+	int rval, i;
+
+	csi2_be_soc->asd.sd.entity.ops = &csi2_be_soc_entity_ops;
+	csi2_be_soc->asd.isys = isys;
+
+	rval = ipu_isys_subdev_init(&csi2_be_soc->asd,
+				    &csi2_be_soc_sd_ops, 0,
+				    NR_OF_CSI2_BE_SOC_PADS,
+				    NR_OF_CSI2_BE_SOC_SOURCE_PADS,
+				    NR_OF_CSI2_BE_SOC_SINK_PADS, 0);
+	if (rval)
+		goto fail;
+
+	csi2_be_soc->asd.pad[CSI2_BE_SOC_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	csi2_be_soc->asd.pad[CSI2_BE_SOC_PAD_SOURCE].flags =
+		MEDIA_PAD_FL_SOURCE;
+	csi2_be_soc->asd.valid_tgts[CSI2_BE_SOC_PAD_SOURCE].crop = true;
+
+	for (i = 0; i < NR_OF_CSI2_BE_SOC_PADS; i++)
+		csi2_be_soc_supported_codes[i] =
+			csi2_be_soc_supported_codes_pad;
+	csi2_be_soc->asd.supported_codes = csi2_be_soc_supported_codes;
+	csi2_be_soc->asd.be_mode = IPU_BE_SOC;
+	csi2_be_soc->asd.isl_mode = IPU_ISL_OFF;
+	csi2_be_soc->asd.set_ffmt = csi2_be_soc_set_ffmt;
+
+	fmt.pad = CSI2_BE_SOC_PAD_SINK;
+	ipu_isys_subdev_set_ffmt(&csi2_be_soc->asd.sd, NULL, &fmt);
+	fmt.pad = CSI2_BE_SOC_PAD_SOURCE;
+	ipu_isys_subdev_set_ffmt(&csi2_be_soc->asd.sd, NULL, &fmt);
+	csi2_be_soc->asd.sd.internal_ops = &csi2_be_soc_sd_internal_ops;
+
+	snprintf(csi2_be_soc->asd.sd.name, sizeof(csi2_be_soc->asd.sd.name),
+		 IPU_ISYS_ENTITY_PREFIX " CSI2 BE SOC %d", index);
+	v4l2_set_subdevdata(&csi2_be_soc->asd.sd, &csi2_be_soc->asd);
+
+	rval = v4l2_device_register_subdev(&isys->v4l2_dev,
+					   &csi2_be_soc->asd.sd);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't register v4l2 subdev\n");
+		goto fail;
+	}
+
+	snprintf(csi2_be_soc->av.vdev.name, sizeof(csi2_be_soc->av.vdev.name),
+		 IPU_ISYS_ENTITY_PREFIX " BE SOC capture %d", index);
+
+	/*
+	 * Pin type could be overwritten for YUV422 to I420 case, at
+	 * set_format phase
+	 */
+	csi2_be_soc->av.aq.css_pin_type = IPU_FW_ISYS_PIN_TYPE_RAW_SOC;
+	csi2_be_soc->av.isys = isys;
+	csi2_be_soc->av.pfmts = ipu_isys_pfmts_be_soc;
+	csi2_be_soc->av.try_fmt_vid_mplane =
+		ipu_isys_video_try_fmt_vid_mplane_default;
+	csi2_be_soc->av.prepare_fw_stream =
+		ipu_isys_prepare_fw_cfg_default;
+	csi2_be_soc->av.aq.buf_prepare = ipu_isys_buf_prepare;
+	csi2_be_soc->av.aq.fill_frame_buff_set_pin =
+		ipu_isys_buffer_to_fw_frame_buff_pin;
+	csi2_be_soc->av.aq.link_fmt_validate = ipu_isys_link_fmt_validate;
+	csi2_be_soc->av.aq.vbq.buf_struct_size =
+		sizeof(struct ipu_isys_video_buffer);
+
+	/* create v4l2 ctrl for be-soc video node */
+	rval = v4l2_ctrl_handler_init(&csi2_be_soc->av.ctrl_handler, 0);
+	if (rval) {
+		dev_err(&isys->adev->dev,
+			"failed to init v4l2 ctrl handler for be_soc\n");
+		goto fail;
+	}
+
+	csi2_be_soc->av.compression_ctrl =
+		v4l2_ctrl_new_custom(&csi2_be_soc->av.ctrl_handler,
+				     &compression_ctrl_cfg, NULL);
+	if (!csi2_be_soc->av.compression_ctrl) {
+		dev_err(&isys->adev->dev,
+			"failed to create BE-SOC cmprs ctrl\n");
+		goto fail;
+	}
+	csi2_be_soc->av.compression = 0;
+	csi2_be_soc->av.vdev.ctrl_handler =
+		&csi2_be_soc->av.ctrl_handler;
+
+	rval = ipu_isys_video_init(&csi2_be_soc->av,
+				   &csi2_be_soc->asd.sd.entity,
+				   CSI2_BE_SOC_PAD_SOURCE,
+				   MEDIA_PAD_FL_SINK,
+				   MEDIA_LNK_FL_DYNAMIC);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't init video node\n");
+		goto fail;
+	}
+
+	return 0;
+
+fail:
+	ipu_isys_csi2_be_soc_cleanup(csi2_be_soc);
+
+	return rval;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-csi2-be.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-csi2-be.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2014 - 2020 Intel Corporation
+
+#include <linux/device.h>
+#include <linux/module.h>
+
+#include <media/ipu-isys.h>
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-isys.h"
+#include "ipu-isys-csi2-be.h"
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-video.h"
+
+/*
+ * Raw bayer format pixel order MUST BE MAINTAINED in groups of four codes.
+ * Otherwise pixel order calculation below WILL BREAK!
+ */
+static const u32 csi2_be_supported_codes_pad[] = {
+	MEDIA_BUS_FMT_SBGGR12_1X12,
+	MEDIA_BUS_FMT_SGBRG12_1X12,
+	MEDIA_BUS_FMT_SGRBG12_1X12,
+	MEDIA_BUS_FMT_SRGGB12_1X12,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	0,
+};
+
+static const u32 *csi2_be_supported_codes[] = {
+	csi2_be_supported_codes_pad,
+	csi2_be_supported_codes_pad,
+};
+
+static struct v4l2_subdev_internal_ops csi2_be_sd_internal_ops = {
+	.open = ipu_isys_subdev_open,
+	.close = ipu_isys_subdev_close,
+};
+
+static const struct v4l2_subdev_core_ops csi2_be_sd_core_ops = {
+};
+
+static const struct v4l2_ctrl_config compression_ctrl_cfg = {
+	.ops = NULL,
+	.id = V4L2_CID_IPU_ISYS_COMPRESSION,
+	.name = "ISYS CSI-BE compression",
+	.type = V4L2_CTRL_TYPE_BOOLEAN,
+	.min = 0,
+	.max = 1,
+	.step = 1,
+	.def = 0,
+};
+
+static int set_stream(struct v4l2_subdev *sd, int enable)
+{
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops csi2_be_sd_video_ops = {
+	.s_stream = set_stream,
+};
+
+static int __subdev_link_validate(struct v4l2_subdev *sd,
+				  struct media_link *link,
+				  struct v4l2_subdev_format *source_fmt,
+				  struct v4l2_subdev_format *sink_fmt)
+{
+	struct ipu_isys_pipeline *ip = container_of(sd->entity.pipe,
+						    struct ipu_isys_pipeline,
+						    pipe);
+
+	ip->csi2_be = to_ipu_isys_csi2_be(sd);
+	return ipu_isys_subdev_link_validate(sd, link, source_fmt, sink_fmt);
+}
+
+static int get_supported_code_index(u32 code)
+{
+	int i;
+
+	for (i = 0; csi2_be_supported_codes_pad[i]; i++) {
+		if (csi2_be_supported_codes_pad[i] == code)
+			return i;
+	}
+	return -EINVAL;
+}
+
+static int ipu_isys_csi2_be_set_sel(struct v4l2_subdev *sd,
+				    struct v4l2_subdev_state *sd_state,
+				    struct v4l2_subdev_selection *sel)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	struct media_pad *pad = &asd->sd.entity.pads[sel->pad];
+
+	if (sel->target == V4L2_SEL_TGT_CROP &&
+	    pad->flags & MEDIA_PAD_FL_SOURCE &&
+	    asd->valid_tgts[CSI2_BE_PAD_SOURCE].crop) {
+		struct v4l2_mbus_framefmt *ffmt =
+			__ipu_isys_get_ffmt(sd, sd_state, sel->pad, sel->which);
+		struct v4l2_rect *r = __ipu_isys_get_selection
+		    (sd, sd_state, sel->target, CSI2_BE_PAD_SINK, sel->which);
+
+		if (get_supported_code_index(ffmt->code) < 0) {
+			/* Non-bayer formats can't be single line cropped */
+			sel->r.left &= ~1;
+			sel->r.top &= ~1;
+
+			/* Non-bayer formats can't pe padded at all */
+			sel->r.width = clamp(sel->r.width,
+					     IPU_ISYS_MIN_WIDTH, r->width);
+		} else {
+			sel->r.width = clamp(sel->r.width,
+					     IPU_ISYS_MIN_WIDTH,
+					     IPU_ISYS_MAX_WIDTH);
+		}
+
+		/*
+		 * Vertical padding is not supported, height is
+		 * restricted by sink pad resolution.
+		 */
+		sel->r.height = clamp(sel->r.height, IPU_ISYS_MIN_HEIGHT,
+				      r->height);
+		*__ipu_isys_get_selection(sd, sd_state, sel->target,
+					sel->pad, sel->which) = sel->r;
+		ipu_isys_subdev_fmt_propagate
+		    (sd, sd_state, NULL, &sel->r,
+		     IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_CROP,
+		     sel->pad, sel->which);
+		return 0;
+	}
+	return ipu_isys_subdev_set_sel(sd, sd_state, sel);
+}
+
+static const struct v4l2_subdev_pad_ops csi2_be_sd_pad_ops = {
+	.link_validate = __subdev_link_validate,
+	.get_fmt = ipu_isys_subdev_get_ffmt,
+	.set_fmt = ipu_isys_subdev_set_ffmt,
+	.get_selection = ipu_isys_subdev_get_sel,
+	.set_selection = ipu_isys_csi2_be_set_sel,
+	.enum_mbus_code = ipu_isys_subdev_enum_mbus_code,
+};
+
+static struct v4l2_subdev_ops csi2_be_sd_ops = {
+	.core = &csi2_be_sd_core_ops,
+	.video = &csi2_be_sd_video_ops,
+	.pad = &csi2_be_sd_pad_ops,
+};
+
+static struct media_entity_operations csi2_be_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static void csi2_be_set_ffmt(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+	struct v4l2_mbus_framefmt *ffmt =
+		__ipu_isys_get_ffmt(sd, sd_state, fmt->pad, fmt->which);
+
+	switch (fmt->pad) {
+	case CSI2_BE_PAD_SINK:
+		if (fmt->format.field != V4L2_FIELD_ALTERNATE)
+			fmt->format.field = V4L2_FIELD_NONE;
+		*ffmt = fmt->format;
+
+		ipu_isys_subdev_fmt_propagate
+		    (sd, sd_state, &fmt->format, NULL,
+		     IPU_ISYS_SUBDEV_PROP_TGT_SINK_FMT, fmt->pad, fmt->which);
+		return;
+	case CSI2_BE_PAD_SOURCE: {
+		struct v4l2_mbus_framefmt *sink_ffmt =
+			__ipu_isys_get_ffmt(sd, sd_state, CSI2_BE_PAD_SINK,
+					    fmt->which);
+		struct v4l2_rect *r =
+			__ipu_isys_get_selection(sd, sd_state, V4L2_SEL_TGT_CROP,
+						 CSI2_BE_PAD_SOURCE,
+						 fmt->which);
+		struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+		u32 code = sink_ffmt->code;
+		int idx = get_supported_code_index(code);
+
+		if (asd->valid_tgts[CSI2_BE_PAD_SOURCE].crop && idx >= 0) {
+			int crop_info = 0;
+
+			if (r->top & 1)
+				crop_info |= CSI2_BE_CROP_VER;
+			if (r->left & 1)
+				crop_info |= CSI2_BE_CROP_HOR;
+			code = csi2_be_supported_codes_pad
+				[((idx & CSI2_BE_CROP_MASK) ^ crop_info)
+				+ (idx & ~CSI2_BE_CROP_MASK)];
+		}
+		ffmt->width = r->width;
+		ffmt->height = r->height;
+		ffmt->code = code;
+		ffmt->field = sink_ffmt->field;
+		return;
+	}
+	default:
+		dev_err(&csi2->isys->adev->dev, "Unknown pad type\n");
+		WARN_ON(1);
+	}
+}
+
+void ipu_isys_csi2_be_cleanup(struct ipu_isys_csi2_be *csi2_be)
+{
+	v4l2_ctrl_handler_free(&csi2_be->av.ctrl_handler);
+	v4l2_device_unregister_subdev(&csi2_be->asd.sd);
+	ipu_isys_subdev_cleanup(&csi2_be->asd);
+	ipu_isys_video_cleanup(&csi2_be->av);
+}
+
+int ipu_isys_csi2_be_init(struct ipu_isys_csi2_be *csi2_be,
+			  struct ipu_isys *isys)
+{
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.pad = CSI2_BE_PAD_SINK,
+		.format = {
+			   .width = 4096,
+			   .height = 3072,
+			  },
+	};
+	struct v4l2_subdev_selection sel = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.pad = CSI2_BE_PAD_SOURCE,
+		.target = V4L2_SEL_TGT_CROP,
+		.r = {
+		      .width = fmt.format.width,
+		      .height = fmt.format.height,
+		     },
+	};
+	int rval;
+
+	csi2_be->asd.sd.entity.ops = &csi2_be_entity_ops;
+	csi2_be->asd.isys = isys;
+
+	rval = ipu_isys_subdev_init(&csi2_be->asd, &csi2_be_sd_ops, 0,
+				    NR_OF_CSI2_BE_PADS,
+				    NR_OF_CSI2_BE_SOURCE_PADS,
+				    NR_OF_CSI2_BE_SINK_PADS, 0);
+	if (rval)
+		goto fail;
+
+	csi2_be->asd.pad[CSI2_BE_PAD_SINK].flags = MEDIA_PAD_FL_SINK
+	    | MEDIA_PAD_FL_MUST_CONNECT;
+	csi2_be->asd.pad[CSI2_BE_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	csi2_be->asd.valid_tgts[CSI2_BE_PAD_SOURCE].crop = true;
+	csi2_be->asd.set_ffmt = csi2_be_set_ffmt;
+
+	BUILD_BUG_ON(ARRAY_SIZE(csi2_be_supported_codes) != NR_OF_CSI2_BE_PADS);
+	csi2_be->asd.supported_codes = csi2_be_supported_codes;
+	csi2_be->asd.be_mode = IPU_BE_RAW;
+	csi2_be->asd.isl_mode = IPU_ISL_CSI2_BE;
+
+	ipu_isys_subdev_set_ffmt(&csi2_be->asd.sd, NULL, &fmt);
+	ipu_isys_csi2_be_set_sel(&csi2_be->asd.sd, NULL, &sel);
+
+	csi2_be->asd.sd.internal_ops = &csi2_be_sd_internal_ops;
+	snprintf(csi2_be->asd.sd.name, sizeof(csi2_be->asd.sd.name),
+		 IPU_ISYS_ENTITY_PREFIX " CSI2 BE");
+	snprintf(csi2_be->av.vdev.name, sizeof(csi2_be->av.vdev.name),
+		 IPU_ISYS_ENTITY_PREFIX " CSI2 BE capture");
+	csi2_be->av.aq.css_pin_type = IPU_FW_ISYS_PIN_TYPE_RAW_NS;
+	v4l2_set_subdevdata(&csi2_be->asd.sd, &csi2_be->asd);
+	rval = v4l2_device_register_subdev(&isys->v4l2_dev, &csi2_be->asd.sd);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't register v4l2 subdev\n");
+		goto fail;
+	}
+
+	csi2_be->av.isys = isys;
+	csi2_be->av.pfmts = ipu_isys_pfmts;
+	csi2_be->av.try_fmt_vid_mplane =
+	    ipu_isys_video_try_fmt_vid_mplane_default;
+	csi2_be->av.prepare_fw_stream =
+	    ipu_isys_prepare_fw_cfg_default;
+	csi2_be->av.aq.buf_prepare = ipu_isys_buf_prepare;
+	csi2_be->av.aq.fill_frame_buff_set_pin =
+	    ipu_isys_buffer_to_fw_frame_buff_pin;
+	csi2_be->av.aq.link_fmt_validate = ipu_isys_link_fmt_validate;
+	csi2_be->av.aq.vbq.buf_struct_size =
+	    sizeof(struct ipu_isys_video_buffer);
+
+	/* create v4l2 ctrl for csi-be video node */
+	rval = v4l2_ctrl_handler_init(&csi2_be->av.ctrl_handler, 0);
+	if (rval) {
+		dev_err(&isys->adev->dev,
+			"failed to init v4l2 ctrl handler for csi2_be\n");
+		goto fail;
+	}
+
+	csi2_be->av.compression_ctrl =
+		v4l2_ctrl_new_custom(&csi2_be->av.ctrl_handler,
+				     &compression_ctrl_cfg, NULL);
+	if (!csi2_be->av.compression_ctrl) {
+		dev_err(&isys->adev->dev,
+			"failed to create CSI-BE cmprs ctrl\n");
+		goto fail;
+	}
+	csi2_be->av.compression = 0;
+	csi2_be->av.vdev.ctrl_handler = &csi2_be->av.ctrl_handler;
+
+	rval = ipu_isys_video_init(&csi2_be->av, &csi2_be->asd.sd.entity,
+				   CSI2_BE_PAD_SOURCE, MEDIA_PAD_FL_SINK, 0);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't init video node\n");
+		goto fail;
+	}
+
+	return 0;
+
+fail:
+	ipu_isys_csi2_be_cleanup(csi2_be);
+
+	return rval;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-csi2-be.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-csi2-be.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2014 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_CSI2_BE_H
+#define IPU_ISYS_CSI2_BE_H
+
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+
+#include "ipu-isys-queue.h"
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-video.h"
+#include "ipu-platform-isys.h"
+
+struct ipu_isys_csi2_be_pdata;
+struct ipu_isys;
+
+#define CSI2_BE_PAD_SINK		0
+#define CSI2_BE_PAD_SOURCE		1
+
+#define NR_OF_CSI2_BE_PADS		2
+#define NR_OF_CSI2_BE_SOURCE_PADS	1
+#define NR_OF_CSI2_BE_SINK_PADS		1
+
+#define NR_OF_CSI2_BE_SOC_SOURCE_PADS	1
+#define NR_OF_CSI2_BE_SOC_SINK_PADS	1
+#define CSI2_BE_SOC_PAD_SINK 0
+#define CSI2_BE_SOC_PAD_SOURCE 1
+#define NR_OF_CSI2_BE_SOC_PADS \
+	(NR_OF_CSI2_BE_SOC_SOURCE_PADS + NR_OF_CSI2_BE_SOC_SINK_PADS)
+
+#define CSI2_BE_CROP_HOR	BIT(0)
+#define CSI2_BE_CROP_VER	BIT(1)
+#define CSI2_BE_CROP_MASK	(CSI2_BE_CROP_VER | CSI2_BE_CROP_HOR)
+
+/*
+ * struct ipu_isys_csi2_be
+ */
+struct ipu_isys_csi2_be {
+	struct ipu_isys_csi2_be_pdata *pdata;
+	struct ipu_isys_subdev asd;
+	struct ipu_isys_video av;
+};
+
+struct ipu_isys_csi2_be_soc {
+	struct ipu_isys_csi2_be_pdata *pdata;
+	struct ipu_isys_subdev asd;
+	struct ipu_isys_video av;
+};
+
+#define to_ipu_isys_csi2_be(sd)	\
+	container_of(to_ipu_isys_subdev(sd), \
+	struct ipu_isys_csi2_be, asd)
+
+#define to_ipu_isys_csi2_be_soc(sd)	\
+	container_of(to_ipu_isys_subdev(sd), \
+	struct ipu_isys_csi2_be_soc, asd)
+
+int ipu_isys_csi2_be_soc_init(struct ipu_isys_csi2_be_soc *csi2_be_soc,
+			      struct ipu_isys *isys, int index);
+void ipu_isys_csi2_be_soc_cleanup(struct ipu_isys_csi2_be_soc *csi2_be);
+
+#endif /* IPU_ISYS_CSI2_BE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-csi2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-csi2.c
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2021 Intel Corporation
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/version.h>
+
+#include <media/ipu-isys.h>
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-buttress.h"
+#include "ipu-isys.h"
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-video.h"
+#include "ipu-platform-regs.h"
+
+static const u32 csi2_supported_codes_pad_sink[] = {
+	MEDIA_BUS_FMT_Y10_1X10,
+	MEDIA_BUS_FMT_RGB565_1X16,
+	MEDIA_BUS_FMT_RGB888_1X24,
+	MEDIA_BUS_FMT_UYVY8_1X16,
+	MEDIA_BUS_FMT_YUYV8_1X16,
+	MEDIA_BUS_FMT_YUYV10_1X20,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8,
+	MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8,
+	MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8,
+	MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8,
+	MEDIA_BUS_FMT_SBGGR12_1X12,
+	MEDIA_BUS_FMT_SGBRG12_1X12,
+	MEDIA_BUS_FMT_SGRBG12_1X12,
+	MEDIA_BUS_FMT_SRGGB12_1X12,
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	0,
+};
+
+static const u32 csi2_supported_codes_pad_source[] = {
+	MEDIA_BUS_FMT_Y10_1X10,
+	MEDIA_BUS_FMT_RGB565_1X16,
+	MEDIA_BUS_FMT_RGB888_1X24,
+	MEDIA_BUS_FMT_UYVY8_1X16,
+	MEDIA_BUS_FMT_YUYV8_1X16,
+	MEDIA_BUS_FMT_YUYV10_1X20,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SBGGR12_1X12,
+	MEDIA_BUS_FMT_SGBRG12_1X12,
+	MEDIA_BUS_FMT_SGRBG12_1X12,
+	MEDIA_BUS_FMT_SRGGB12_1X12,
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	0,
+};
+
+static const u32 *csi2_supported_codes[NR_OF_CSI2_PADS];
+
+static struct v4l2_subdev_internal_ops csi2_sd_internal_ops = {
+	.open = ipu_isys_subdev_open,
+	.close = ipu_isys_subdev_close,
+};
+
+int ipu_isys_csi2_get_link_freq(struct ipu_isys_csi2 *csi2, __s64 *link_freq)
+{
+	struct ipu_isys_pipeline *pipe = container_of(csi2->asd.sd.entity.pipe,
+						      struct ipu_isys_pipeline,
+						      pipe);
+	struct v4l2_subdev *ext_sd =
+	    media_entity_to_v4l2_subdev(pipe->external->entity);
+	struct v4l2_ext_control c = {.id = V4L2_CID_LINK_FREQ, };
+	struct v4l2_ext_controls cs = {.count = 1,
+		.controls = &c,
+	};
+	struct v4l2_querymenu qm = {.id = c.id, };
+	int rval;
+
+	if (!ext_sd) {
+		WARN_ON(1);
+		return -ENODEV;
+	}
+	rval = v4l2_g_ext_ctrls(ext_sd->ctrl_handler,
+				ext_sd->devnode,
+				ext_sd->v4l2_dev->mdev,
+				&cs);
+	if (rval) {
+		dev_info(&csi2->isys->adev->dev, "can't get link frequency\n");
+		return rval;
+	}
+
+	qm.index = c.value;
+
+	rval = v4l2_querymenu(ext_sd->ctrl_handler, &qm);
+	if (rval) {
+		dev_info(&csi2->isys->adev->dev, "can't get menu item\n");
+		return rval;
+	}
+
+	dev_dbg(&csi2->isys->adev->dev, "%s: link frequency %lld\n", __func__,
+		qm.value);
+
+	if (!qm.value)
+		return -EINVAL;
+	*link_freq = qm.value;
+	return 0;
+}
+
+static int subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			   struct v4l2_event_subscription *sub)
+{
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+
+	dev_dbg(&csi2->isys->adev->dev, "subscribe event(type %u id %u)\n",
+		sub->type, sub->id);
+
+	switch (sub->type) {
+	case V4L2_EVENT_FRAME_SYNC:
+		return v4l2_event_subscribe(fh, sub, 10, NULL);
+	case V4L2_EVENT_CTRL:
+		return v4l2_ctrl_subscribe_event(fh, sub);
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct v4l2_subdev_core_ops csi2_sd_core_ops = {
+	.subscribe_event = subscribe_event,
+	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+/*
+ * The input system CSI2+ receiver has several
+ * parameters affecting the receiver timings. These depend
+ * on the MIPI bus frequency F in Hz (sensor transmitter rate)
+ * as follows:
+ *	register value = (A/1e9 + B * UI) / COUNT_ACC
+ * where
+ *	UI = 1 / (2 * F) in seconds
+ *	COUNT_ACC = counter accuracy in seconds
+ *	For legacy IPU,  COUNT_ACC = 0.125 ns
+ *
+ * A and B are coefficients from the table below,
+ * depending whether the register minimum or maximum value is
+ * calculated.
+ *				       Minimum     Maximum
+ * Clock lane			       A     B     A     B
+ * reg_rx_csi_dly_cnt_termen_clane     0     0    38     0
+ * reg_rx_csi_dly_cnt_settle_clane    95    -8   300   -16
+ * Data lanes
+ * reg_rx_csi_dly_cnt_termen_dlane0    0     0    35     4
+ * reg_rx_csi_dly_cnt_settle_dlane0   85    -2   145    -6
+ * reg_rx_csi_dly_cnt_termen_dlane1    0     0    35     4
+ * reg_rx_csi_dly_cnt_settle_dlane1   85    -2   145    -6
+ * reg_rx_csi_dly_cnt_termen_dlane2    0     0    35     4
+ * reg_rx_csi_dly_cnt_settle_dlane2   85    -2   145    -6
+ * reg_rx_csi_dly_cnt_termen_dlane3    0     0    35     4
+ * reg_rx_csi_dly_cnt_settle_dlane3   85    -2   145    -6
+ *
+ * We use the minimum values of both A and B.
+ */
+
+#define DIV_SHIFT	8
+
+static uint32_t calc_timing(s32 a, int32_t b, int64_t link_freq, int32_t accinv)
+{
+	return accinv * a + (accinv * b * (500000000 >> DIV_SHIFT)
+			     / (int32_t)(link_freq >> DIV_SHIFT));
+}
+
+static int
+ipu_isys_csi2_calc_timing(struct ipu_isys_csi2 *csi2,
+			  struct ipu_isys_csi2_timing *timing, uint32_t accinv)
+{
+	__s64 link_freq;
+	int rval;
+
+	rval = ipu_isys_csi2_get_link_freq(csi2, &link_freq);
+	if (rval)
+		return rval;
+
+	timing->ctermen = calc_timing(CSI2_CSI_RX_DLY_CNT_TERMEN_CLANE_A,
+				      CSI2_CSI_RX_DLY_CNT_TERMEN_CLANE_B,
+				      link_freq, accinv);
+	timing->csettle = calc_timing(CSI2_CSI_RX_DLY_CNT_SETTLE_CLANE_A,
+				      CSI2_CSI_RX_DLY_CNT_SETTLE_CLANE_B,
+				      link_freq, accinv);
+	dev_dbg(&csi2->isys->adev->dev, "ctermen %u\n", timing->ctermen);
+	dev_dbg(&csi2->isys->adev->dev, "csettle %u\n", timing->csettle);
+
+	timing->dtermen = calc_timing(CSI2_CSI_RX_DLY_CNT_TERMEN_DLANE_A,
+				      CSI2_CSI_RX_DLY_CNT_TERMEN_DLANE_B,
+				      link_freq, accinv);
+	timing->dsettle = calc_timing(CSI2_CSI_RX_DLY_CNT_SETTLE_DLANE_A,
+				      CSI2_CSI_RX_DLY_CNT_SETTLE_DLANE_B,
+				      link_freq, accinv);
+	dev_dbg(&csi2->isys->adev->dev, "dtermen %u\n", timing->dtermen);
+	dev_dbg(&csi2->isys->adev->dev, "dsettle %u\n", timing->dsettle);
+
+	return 0;
+}
+
+#define CSI2_ACCINV	8
+
+static int set_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+	struct ipu_isys_pipeline *ip = container_of(sd->entity.pipe,
+						    struct ipu_isys_pipeline,
+						    pipe);
+	struct ipu_isys_csi2_config *cfg;
+	struct v4l2_subdev *ext_sd;
+	struct ipu_isys_csi2_timing timing = {0};
+	unsigned int nlanes;
+	int rval;
+
+	dev_dbg(&csi2->isys->adev->dev, "csi2 s_stream %d\n", enable);
+
+	if (!ip->external->entity) {
+		WARN_ON(1);
+		return -ENODEV;
+	}
+	ext_sd = media_entity_to_v4l2_subdev(ip->external->entity);
+	cfg = v4l2_get_subdev_hostdata(ext_sd);
+
+	if (!enable) {
+		ipu_isys_csi2_set_stream(sd, timing, 0, enable);
+		return 0;
+	}
+
+	ip->has_sof = true;
+
+	nlanes = cfg->nlanes;
+
+	dev_dbg(&csi2->isys->adev->dev, "lane nr %d.\n", nlanes);
+
+	rval = ipu_isys_csi2_calc_timing(csi2, &timing, CSI2_ACCINV);
+	if (rval)
+		return rval;
+
+	rval = ipu_isys_csi2_set_stream(sd, timing, nlanes, enable);
+
+	return rval;
+}
+
+static void csi2_capture_done(struct ipu_isys_pipeline *ip,
+			      struct ipu_fw_isys_resp_info_abi *info)
+{
+	if (ip->interlaced && ip->isys->short_packet_source ==
+	    IPU_ISYS_SHORT_PACKET_FROM_RECEIVER) {
+		struct ipu_isys_buffer *ib;
+		unsigned long flags;
+
+		spin_lock_irqsave(&ip->short_packet_queue_lock, flags);
+		if (!list_empty(&ip->short_packet_active)) {
+			ib = list_last_entry(&ip->short_packet_active,
+					     struct ipu_isys_buffer, head);
+			list_move(&ib->head, &ip->short_packet_incoming);
+		}
+		spin_unlock_irqrestore(&ip->short_packet_queue_lock, flags);
+	}
+}
+
+static int csi2_link_validate(struct media_link *link)
+{
+	struct ipu_isys_csi2 *csi2;
+	struct ipu_isys_pipeline *ip;
+	int rval;
+
+	if (!link->sink->entity ||
+	    !link->sink->entity->pipe || !link->source->entity)
+		return -EINVAL;
+	csi2 =
+	    to_ipu_isys_csi2(media_entity_to_v4l2_subdev(link->sink->entity));
+	ip = to_ipu_isys_pipeline(link->sink->entity->pipe);
+	csi2->receiver_errors = 0;
+	ip->csi2 = csi2;
+	ipu_isys_video_add_capture_done(to_ipu_isys_pipeline
+					(link->sink->entity->pipe),
+					csi2_capture_done);
+
+	rval = v4l2_subdev_link_validate(link);
+	if (rval)
+		return rval;
+
+	if (!v4l2_ctrl_g_ctrl(csi2->store_csi2_header)) {
+		struct media_pad *remote_pad =
+		    media_entity_remote_pad(&csi2->asd.pad[CSI2_PAD_SOURCE]);
+
+		if (remote_pad &&
+		    is_media_entity_v4l2_subdev(remote_pad->entity)) {
+			dev_err(&csi2->isys->adev->dev,
+				"CSI2 BE requires CSI2 headers.\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops csi2_sd_video_ops = {
+	.s_stream = set_stream,
+};
+
+static int ipu_isys_csi2_get_fmt(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	return ipu_isys_subdev_get_ffmt(sd, sd_state, fmt);
+}
+
+static int ipu_isys_csi2_set_fmt(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	return ipu_isys_subdev_set_ffmt(sd, sd_state, fmt);
+}
+
+static int __subdev_link_validate(struct v4l2_subdev *sd,
+				  struct media_link *link,
+				  struct v4l2_subdev_format *source_fmt,
+				  struct v4l2_subdev_format *sink_fmt)
+{
+	struct ipu_isys_pipeline *ip = container_of(sd->entity.pipe,
+						    struct ipu_isys_pipeline,
+						    pipe);
+
+	if (source_fmt->format.field == V4L2_FIELD_ALTERNATE)
+		ip->interlaced = true;
+
+	return ipu_isys_subdev_link_validate(sd, link, source_fmt, sink_fmt);
+}
+
+static const struct v4l2_subdev_pad_ops csi2_sd_pad_ops = {
+	.link_validate = __subdev_link_validate,
+	.get_fmt = ipu_isys_csi2_get_fmt,
+	.set_fmt = ipu_isys_csi2_set_fmt,
+	.enum_mbus_code = ipu_isys_subdev_enum_mbus_code,
+};
+
+static struct v4l2_subdev_ops csi2_sd_ops = {
+	.core = &csi2_sd_core_ops,
+	.video = &csi2_sd_video_ops,
+	.pad = &csi2_sd_pad_ops,
+};
+
+static struct media_entity_operations csi2_entity_ops = {
+	.link_validate = csi2_link_validate,
+};
+
+static void csi2_set_ffmt(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_state *sd_state,
+			  struct v4l2_subdev_format *fmt)
+{
+	enum isys_subdev_prop_tgt tgt = IPU_ISYS_SUBDEV_PROP_TGT_SINK_FMT;
+	struct v4l2_mbus_framefmt *ffmt =
+		__ipu_isys_get_ffmt(sd, sd_state, fmt->pad,
+				    fmt->which);
+
+	if (fmt->format.field != V4L2_FIELD_ALTERNATE)
+		fmt->format.field = V4L2_FIELD_NONE;
+
+	if (fmt->pad == CSI2_PAD_SINK) {
+		*ffmt = fmt->format;
+		ipu_isys_subdev_fmt_propagate(sd, sd_state, &fmt->format, NULL,
+					      tgt, fmt->pad, fmt->which);
+		return;
+	}
+
+	if (sd->entity.pads[fmt->pad].flags & MEDIA_PAD_FL_SOURCE) {
+		ffmt->width = fmt->format.width;
+		ffmt->height = fmt->format.height;
+		ffmt->field = fmt->format.field;
+		ffmt->code =
+		    ipu_isys_subdev_code_to_uncompressed(fmt->format.code);
+		return;
+	}
+
+	WARN_ON(1);
+}
+
+static const struct ipu_isys_pixelformat *
+csi2_try_fmt(struct ipu_isys_video *av,
+	     struct v4l2_pix_format_mplane *mpix)
+{
+	struct media_link *link = list_first_entry(&av->vdev.entity.links,
+						   struct media_link, list);
+	struct v4l2_subdev *sd =
+	    media_entity_to_v4l2_subdev(link->source->entity);
+	struct ipu_isys_csi2 *csi2;
+
+	if (!sd)
+		return NULL;
+
+	csi2 = to_ipu_isys_csi2(sd);
+
+	return ipu_isys_video_try_fmt_vid_mplane(av, mpix,
+				v4l2_ctrl_g_ctrl(csi2->store_csi2_header));
+}
+
+void ipu_isys_csi2_cleanup(struct ipu_isys_csi2 *csi2)
+{
+	if (!csi2->isys)
+		return;
+
+	v4l2_device_unregister_subdev(&csi2->asd.sd);
+	ipu_isys_subdev_cleanup(&csi2->asd);
+	csi2->isys = NULL;
+}
+
+static void csi_ctrl_init(struct v4l2_subdev *sd)
+{
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+
+	static const struct v4l2_ctrl_config cfg = {
+		.id = V4L2_CID_IPU_STORE_CSI2_HEADER,
+		.name = "Store CSI-2 Headers",
+		.type = V4L2_CTRL_TYPE_BOOLEAN,
+		.min = 0,
+		.max = 1,
+		.step = 1,
+		.def = 1,
+	};
+
+	csi2->store_csi2_header = v4l2_ctrl_new_custom(&csi2->asd.ctrl_handler,
+						       &cfg, NULL);
+}
+
+int ipu_isys_csi2_init(struct ipu_isys_csi2 *csi2,
+		       struct ipu_isys *isys,
+		       void __iomem *base, unsigned int index)
+{
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.pad = CSI2_PAD_SINK,
+		.format = {
+			   .width = 4096,
+			   .height = 3072,
+			  },
+	};
+	int i, rval, src;
+
+	dev_dbg(&isys->adev->dev, "csi-%d base = 0x%lx\n", index,
+		(unsigned long)base);
+	csi2->isys = isys;
+	csi2->base = base;
+	csi2->index = index;
+
+	csi2->asd.sd.entity.ops = &csi2_entity_ops;
+	csi2->asd.ctrl_init = csi_ctrl_init;
+	csi2->asd.isys = isys;
+	init_completion(&csi2->eof_completion);
+	rval = ipu_isys_subdev_init(&csi2->asd, &csi2_sd_ops, 0,
+				    NR_OF_CSI2_PADS,
+				    NR_OF_CSI2_SOURCE_PADS,
+				    NR_OF_CSI2_SINK_PADS,
+				    0);
+	if (rval)
+		goto fail;
+
+	csi2->asd.pad[CSI2_PAD_SINK].flags = MEDIA_PAD_FL_SINK
+		| MEDIA_PAD_FL_MUST_CONNECT;
+	csi2->asd.pad[CSI2_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	src = index;
+	csi2->asd.source = IPU_FW_ISYS_STREAM_SRC_CSI2_PORT0 + src;
+	csi2_supported_codes[CSI2_PAD_SINK] = csi2_supported_codes_pad_sink;
+
+	for (i = 0; i < NR_OF_CSI2_SOURCE_PADS; i++)
+		csi2_supported_codes[i + 1] = csi2_supported_codes_pad_source;
+	csi2->asd.supported_codes = csi2_supported_codes;
+	csi2->asd.set_ffmt = csi2_set_ffmt;
+
+	csi2->asd.sd.flags |= V4L2_SUBDEV_FL_HAS_EVENTS;
+	csi2->asd.sd.internal_ops = &csi2_sd_internal_ops;
+	snprintf(csi2->asd.sd.name, sizeof(csi2->asd.sd.name),
+		 IPU_ISYS_ENTITY_PREFIX " CSI-2 %u", index);
+	v4l2_set_subdevdata(&csi2->asd.sd, &csi2->asd);
+
+	rval = v4l2_device_register_subdev(&isys->v4l2_dev, &csi2->asd.sd);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't register v4l2 subdev\n");
+		goto fail;
+	}
+
+	mutex_lock(&csi2->asd.mutex);
+	__ipu_isys_subdev_set_ffmt(&csi2->asd.sd, NULL, &fmt);
+	mutex_unlock(&csi2->asd.mutex);
+
+	return 0;
+
+fail:
+	ipu_isys_csi2_cleanup(csi2);
+
+	return rval;
+}
+
+void ipu_isys_csi2_sof_event(struct ipu_isys_csi2 *csi2)
+{
+	struct ipu_isys_pipeline *ip = NULL;
+	struct v4l2_event ev = {
+		.type = V4L2_EVENT_FRAME_SYNC,
+	};
+	struct video_device *vdev = csi2->asd.sd.devnode;
+	unsigned long flags;
+	unsigned int i;
+
+	spin_lock_irqsave(&csi2->isys->lock, flags);
+	csi2->in_frame = true;
+
+	for (i = 0; i < IPU_ISYS_MAX_STREAMS; i++) {
+		if (csi2->isys->pipes[i] &&
+		    csi2->isys->pipes[i]->csi2 == csi2) {
+			ip = csi2->isys->pipes[i];
+			break;
+		}
+	}
+
+	/* Pipe already vanished */
+	if (!ip) {
+		spin_unlock_irqrestore(&csi2->isys->lock, flags);
+		return;
+	}
+
+	ev.u.frame_sync.frame_sequence = atomic_inc_return(&ip->sequence) - 1;
+	spin_unlock_irqrestore(&csi2->isys->lock, flags);
+
+	v4l2_event_queue(vdev, &ev);
+	dev_dbg(&csi2->isys->adev->dev,
+		"sof_event::csi2-%i sequence: %i\n",
+		csi2->index, ev.u.frame_sync.frame_sequence);
+}
+
+void ipu_isys_csi2_eof_event(struct ipu_isys_csi2 *csi2)
+{
+	struct ipu_isys_pipeline *ip = NULL;
+	unsigned long flags;
+	unsigned int i;
+	u32 frame_sequence;
+
+	spin_lock_irqsave(&csi2->isys->lock, flags);
+	csi2->in_frame = false;
+	if (csi2->wait_for_sync)
+		complete(&csi2->eof_completion);
+
+	for (i = 0; i < IPU_ISYS_MAX_STREAMS; i++) {
+		if (csi2->isys->pipes[i] &&
+		    csi2->isys->pipes[i]->csi2 == csi2) {
+			ip = csi2->isys->pipes[i];
+			break;
+		}
+	}
+
+	if (ip) {
+		frame_sequence = atomic_read(&ip->sequence);
+		spin_unlock_irqrestore(&csi2->isys->lock, flags);
+
+		dev_dbg(&csi2->isys->adev->dev,
+			"eof_event::csi2-%i sequence: %i\n",
+			csi2->index, frame_sequence);
+		return;
+	}
+
+	spin_unlock_irqrestore(&csi2->isys->lock, flags);
+}
+
+/* Call this function only _after_ the sensor has been stopped */
+void ipu_isys_csi2_wait_last_eof(struct ipu_isys_csi2 *csi2)
+{
+	unsigned long flags, tout;
+
+	spin_lock_irqsave(&csi2->isys->lock, flags);
+
+	if (!csi2->in_frame) {
+		spin_unlock_irqrestore(&csi2->isys->lock, flags);
+		return;
+	}
+
+	reinit_completion(&csi2->eof_completion);
+	csi2->wait_for_sync = true;
+	spin_unlock_irqrestore(&csi2->isys->lock, flags);
+	tout = wait_for_completion_timeout(&csi2->eof_completion,
+					   IPU_EOF_TIMEOUT_JIFFIES);
+	if (!tout)
+		dev_err(&csi2->isys->adev->dev,
+			"csi2-%d: timeout at sync to eof\n",
+			csi2->index);
+	csi2->wait_for_sync = false;
+}
+
+struct ipu_isys_buffer *
+ipu_isys_csi2_get_short_packet_buffer(struct ipu_isys_pipeline *ip,
+				      struct ipu_isys_buffer_list *bl)
+{
+	struct ipu_isys_buffer *ib;
+	struct ipu_isys_private_buffer *pb;
+	struct ipu_isys_mipi_packet_header *ph;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ip->short_packet_queue_lock, flags);
+	if (list_empty(&ip->short_packet_incoming)) {
+		spin_unlock_irqrestore(&ip->short_packet_queue_lock, flags);
+		return NULL;
+	}
+	ib = list_last_entry(&ip->short_packet_incoming,
+			     struct ipu_isys_buffer, head);
+	pb = ipu_isys_buffer_to_private_buffer(ib);
+	ph = (struct ipu_isys_mipi_packet_header *)pb->buffer;
+
+	/* Fill the packet header with magic number. */
+	ph->word_count = 0xffff;
+	ph->dtype = 0xff;
+
+	dma_sync_single_for_cpu(&ip->isys->adev->dev, pb->dma_addr,
+				sizeof(*ph), DMA_BIDIRECTIONAL);
+	spin_unlock_irqrestore(&ip->short_packet_queue_lock, flags);
+	list_move(&ib->head, &bl->head);
+
+	return ib;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-csi2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-csi2.h
@@ -0,0 +1,164 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_CSI2_H
+#define IPU_ISYS_CSI2_H
+
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+
+#include "ipu-isys-queue.h"
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-video.h"
+#include "ipu-platform-isys.h"
+
+struct ipu_isys_csi2_timing;
+struct ipu_isys_csi2_pdata;
+struct ipu_isys;
+
+#define NR_OF_CSI2_SINK_PADS		1
+#define CSI2_PAD_SINK			0
+#define NR_OF_CSI2_SOURCE_PADS		1
+#define CSI2_PAD_SOURCE			1
+#define NR_OF_CSI2_PADS	(NR_OF_CSI2_SINK_PADS + NR_OF_CSI2_SOURCE_PADS)
+
+#define IPU_ISYS_SHORT_PACKET_BUFFER_NUM	VIDEO_MAX_FRAME
+#define IPU_ISYS_SHORT_PACKET_WIDTH	32
+#define IPU_ISYS_SHORT_PACKET_FRAME_PACKETS	2
+#define IPU_ISYS_SHORT_PACKET_EXTRA_PACKETS	64
+#define IPU_ISYS_SHORT_PACKET_UNITSIZE	8
+#define IPU_ISYS_SHORT_PACKET_GENERAL_DT	0
+#define IPU_ISYS_SHORT_PACKET_PT		0
+#define IPU_ISYS_SHORT_PACKET_FT		0
+
+#define IPU_ISYS_SHORT_PACKET_STRIDE \
+	(IPU_ISYS_SHORT_PACKET_WIDTH * \
+	IPU_ISYS_SHORT_PACKET_UNITSIZE)
+#define IPU_ISYS_SHORT_PACKET_NUM(num_lines) \
+	((num_lines) * 2 + IPU_ISYS_SHORT_PACKET_FRAME_PACKETS + \
+	IPU_ISYS_SHORT_PACKET_EXTRA_PACKETS)
+#define IPU_ISYS_SHORT_PACKET_PKT_LINES(num_lines) \
+	DIV_ROUND_UP(IPU_ISYS_SHORT_PACKET_NUM(num_lines) * \
+	IPU_ISYS_SHORT_PACKET_UNITSIZE, \
+	IPU_ISYS_SHORT_PACKET_STRIDE)
+#define IPU_ISYS_SHORT_PACKET_BUF_SIZE(num_lines) \
+	(IPU_ISYS_SHORT_PACKET_WIDTH * \
+	IPU_ISYS_SHORT_PACKET_PKT_LINES(num_lines) * \
+	IPU_ISYS_SHORT_PACKET_UNITSIZE)
+
+#define IPU_ISYS_SHORT_PACKET_TRACE_MSG_NUMBER	256
+#define IPU_ISYS_SHORT_PACKET_TRACE_MSG_SIZE	16
+#define IPU_ISYS_SHORT_PACKET_TRACE_BUFFER_SIZE \
+	(IPU_ISYS_SHORT_PACKET_TRACE_MSG_NUMBER * \
+	IPU_ISYS_SHORT_PACKET_TRACE_MSG_SIZE)
+
+#define IPU_ISYS_SHORT_PACKET_FROM_RECEIVER	0
+#define IPU_ISYS_SHORT_PACKET_FROM_TUNIT		1
+
+#define IPU_ISYS_SHORT_PACKET_TRACE_MAX_TIMESHIFT 100
+#define IPU_ISYS_SHORT_PACKET_TRACE_EVENT_MASK	0x2082
+#define IPU_SKEW_CAL_LIMIT_HZ (1500000000ul / 2)
+
+#define CSI2_CSI_RX_DLY_CNT_TERMEN_CLANE_A		0
+#define CSI2_CSI_RX_DLY_CNT_TERMEN_CLANE_B		0
+#define CSI2_CSI_RX_DLY_CNT_SETTLE_CLANE_A		95
+#define CSI2_CSI_RX_DLY_CNT_SETTLE_CLANE_B		-8
+
+#define CSI2_CSI_RX_DLY_CNT_TERMEN_DLANE_A		0
+#define CSI2_CSI_RX_DLY_CNT_TERMEN_DLANE_B		0
+#define CSI2_CSI_RX_DLY_CNT_SETTLE_DLANE_A		85
+#define CSI2_CSI_RX_DLY_CNT_SETTLE_DLANE_B		-2
+
+#define IPU_EOF_TIMEOUT 300
+#define IPU_EOF_TIMEOUT_JIFFIES msecs_to_jiffies(IPU_EOF_TIMEOUT)
+
+/*
+ * struct ipu_isys_csi2
+ *
+ * @nlanes: number of lanes in the receiver
+ */
+struct ipu_isys_csi2 {
+	struct ipu_isys_csi2_pdata *pdata;
+	struct ipu_isys *isys;
+	struct ipu_isys_subdev asd;
+	struct ipu_isys_video av;
+	struct completion eof_completion;
+
+	void __iomem *base;
+	u32 receiver_errors;
+	unsigned int nlanes;
+	unsigned int index;
+	atomic_t sof_sequence;
+	bool in_frame;
+	bool wait_for_sync;
+
+	struct v4l2_ctrl *store_csi2_header;
+};
+
+struct ipu_isys_csi2_timing {
+	u32 ctermen;
+	u32 csettle;
+	u32 dtermen;
+	u32 dsettle;
+};
+
+/*
+ * This structure defines the MIPI packet header output
+ * from IPU MIPI receiver. Due to hardware conversion,
+ * this structure is not the same as defined in CSI-2 spec.
+ */
+struct ipu_isys_mipi_packet_header {
+	u32 word_count:16, dtype:13, sync:2, stype:1;
+	u32 sid:4, port_id:4, reserved:23, odd_even:1;
+} __packed;
+
+/*
+ * This structure defines the trace message content
+ * for CSI2 receiver monitor messages.
+ */
+struct ipu_isys_csi2_monitor_message {
+	u64 fe:1,
+	    fs:1,
+	    pe:1,
+	    ps:1,
+	    le:1,
+	    ls:1,
+	    reserved1:2,
+	    sequence:2,
+	    reserved2:2,
+	    flash_shutter:4,
+	    error_cause:12,
+	    fifo_overrun:1,
+	    crc_error:2,
+	    reserved3:1,
+	    timestamp_l:16,
+	    port:4, vc:2, reserved4:2, frame_sync:4, reserved5:4;
+	u64 reserved6:3,
+	    cmd:2, reserved7:1, monitor_id:7, reserved8:1, timestamp_h:50;
+} __packed;
+
+#define to_ipu_isys_csi2(sd) container_of(to_ipu_isys_subdev(sd), \
+					struct ipu_isys_csi2, asd)
+
+int ipu_isys_csi2_get_link_freq(struct ipu_isys_csi2 *csi2, __s64 *link_freq);
+int ipu_isys_csi2_init(struct ipu_isys_csi2 *csi2,
+		       struct ipu_isys *isys,
+		       void __iomem *base, unsigned int index);
+void ipu_isys_csi2_cleanup(struct ipu_isys_csi2 *csi2);
+struct ipu_isys_buffer *
+ipu_isys_csi2_get_short_packet_buffer(struct ipu_isys_pipeline *ip,
+				      struct ipu_isys_buffer_list *bl);
+void ipu_isys_csi2_sof_event(struct ipu_isys_csi2 *csi2);
+void ipu_isys_csi2_eof_event(struct ipu_isys_csi2 *csi2);
+void ipu_isys_csi2_wait_last_eof(struct ipu_isys_csi2 *csi2);
+
+/* interface for platform specific */
+int ipu_isys_csi2_set_stream(struct v4l2_subdev *sd,
+			     struct ipu_isys_csi2_timing timing,
+			     unsigned int nlanes, int enable);
+unsigned int ipu_isys_csi2_get_current_field(struct ipu_isys_pipeline *ip,
+					     unsigned int *timestamp);
+void ipu_isys_csi2_isr(struct ipu_isys_csi2 *csi2);
+void ipu_isys_csi2_error(struct ipu_isys_csi2 *csi2);
+
+#endif /* IPU_ISYS_CSI2_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-media.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-media.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2016 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_MEDIA_H
+#define IPU_ISYS_MEDIA_H
+
+#include <linux/slab.h>
+#include <media/media-entity.h>
+
+struct __packed media_request_cmd {
+	__u32 cmd;
+	__u32 request;
+	__u32 flags;
+};
+
+struct __packed media_event_request_complete {
+	__u32 id;
+};
+
+#define MEDIA_EVENT_TYPE_REQUEST_COMPLETE	1
+
+struct __packed media_event {
+	__u32 type;
+	__u32 sequence;
+	__u32 reserved[4];
+
+	union {
+		struct media_event_request_complete req_complete;
+	};
+};
+
+enum media_device_request_state {
+	MEDIA_DEVICE_REQUEST_STATE_IDLE,
+	MEDIA_DEVICE_REQUEST_STATE_QUEUED,
+	MEDIA_DEVICE_REQUEST_STATE_DELETED,
+	MEDIA_DEVICE_REQUEST_STATE_COMPLETE,
+};
+
+struct media_kevent {
+	struct list_head list;
+	struct media_event ev;
+};
+
+struct media_device_request {
+	u32 id;
+	struct media_device *mdev;
+	struct file *filp;
+	struct media_kevent *kev;
+	struct kref kref;
+	struct list_head list;
+	struct list_head fh_list;
+	enum media_device_request_state state;
+	struct list_head data;
+	u32 flags;
+};
+
+static inline struct media_device_request *
+media_device_request_find(struct media_device *mdev, u16 reqid)
+{
+	return NULL;
+}
+
+static inline void media_device_request_get(struct media_device_request *req)
+{
+}
+
+static inline void media_device_request_put(struct media_device_request *req)
+{
+}
+
+static inline void
+media_device_request_complete(struct media_device *mdev,
+			      struct media_device_request *req)
+{
+}
+
+#endif /* IPU_ISYS_MEDIA_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-queue.c
@@ -0,0 +1,1063 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/string.h>
+
+#include <media/media-entity.h>
+#include <media/videobuf2-dma-contig.h>
+#include <media/v4l2-ioctl.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-buttress.h"
+#include "ipu-isys.h"
+#include "ipu-isys-csi2.h"
+#include "ipu-isys-video.h"
+
+static bool wall_clock_ts_on;
+module_param(wall_clock_ts_on, bool, 0660);
+MODULE_PARM_DESC(wall_clock_ts_on, "Timestamp based on REALTIME clock");
+
+static int queue_setup(struct vb2_queue *q,
+		       unsigned int *num_buffers, unsigned int *num_planes,
+		       unsigned int sizes[],
+		       struct device *alloc_devs[])
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(q);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	bool use_fmt = false;
+	unsigned int i;
+
+	/* num_planes == 0: we're being called through VIDIOC_REQBUFS */
+	if (!*num_planes) {
+		use_fmt = true;
+		*num_planes = av->mpix.num_planes;
+	}
+
+	for (i = 0; i < *num_planes; i++) {
+		if (use_fmt)
+			sizes[i] = av->mpix.plane_fmt[i].sizeimage;
+		alloc_devs[i] = aq->dev;
+		dev_dbg(&av->isys->adev->dev,
+			"%s: queue setup: plane %d size %u\n",
+			av->vdev.name, i, sizes[i]);
+	}
+
+	return 0;
+}
+
+static void ipu_isys_queue_lock(struct vb2_queue *q)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(q);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+	dev_dbg(&av->isys->adev->dev, "%s: queue lock\n", av->vdev.name);
+	mutex_lock(&av->mutex);
+}
+
+static void ipu_isys_queue_unlock(struct vb2_queue *q)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(q);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+	dev_dbg(&av->isys->adev->dev, "%s: queue unlock\n", av->vdev.name);
+	mutex_unlock(&av->mutex);
+}
+
+static int buf_init(struct vb2_buffer *vb)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+	dev_dbg(&av->isys->adev->dev, "buffer: %s: %s\n", av->vdev.name,
+		__func__);
+
+	if (aq->buf_init)
+		return aq->buf_init(vb);
+
+	return 0;
+}
+
+int ipu_isys_buf_prepare(struct vb2_buffer *vb)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+	dev_dbg(&av->isys->adev->dev,
+		"buffer: %s: configured size %u, buffer size %lu\n",
+		av->vdev.name,
+		av->mpix.plane_fmt[0].sizeimage, vb2_plane_size(vb, 0));
+
+	if (av->mpix.plane_fmt[0].sizeimage > vb2_plane_size(vb, 0))
+		return -EINVAL;
+
+	vb2_set_plane_payload(vb, 0, av->mpix.plane_fmt[0].bytesperline *
+			      av->mpix.height);
+	vb->planes[0].data_offset = av->line_header_length / BITS_PER_BYTE;
+
+	return 0;
+}
+
+static int buf_prepare(struct vb2_buffer *vb)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	int rval;
+
+	if (av->isys->adev->isp->flr_done)
+		return -EIO;
+
+	rval = aq->buf_prepare(vb);
+	return rval;
+}
+
+static void buf_finish(struct vb2_buffer *vb)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+	dev_dbg(&av->isys->adev->dev, "buffer: %s: %s\n", av->vdev.name,
+		__func__);
+
+}
+
+static void buf_cleanup(struct vb2_buffer *vb)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+	dev_dbg(&av->isys->adev->dev, "buffer: %s: %s\n", av->vdev.name,
+		__func__);
+
+	if (aq->buf_cleanup)
+		return aq->buf_cleanup(vb);
+}
+
+/*
+ * Queue a buffer list back to incoming or active queues. The buffers
+ * are removed from the buffer list.
+ */
+void ipu_isys_buffer_list_queue(struct ipu_isys_buffer_list *bl,
+				unsigned long op_flags,
+				enum vb2_buffer_state state)
+{
+	struct ipu_isys_buffer *ib, *ib_safe;
+	unsigned long flags;
+	bool first = true;
+
+	if (!bl)
+		return;
+
+	WARN_ON(!bl->nbufs);
+	WARN_ON(op_flags & IPU_ISYS_BUFFER_LIST_FL_ACTIVE &&
+		op_flags & IPU_ISYS_BUFFER_LIST_FL_INCOMING);
+
+	list_for_each_entry_safe(ib, ib_safe, &bl->head, head) {
+		struct ipu_isys_video *av;
+
+		if (ib->type == IPU_ISYS_VIDEO_BUFFER) {
+			struct vb2_buffer *vb =
+			    ipu_isys_buffer_to_vb2_buffer(ib);
+			struct ipu_isys_queue *aq =
+			    vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+
+			av = ipu_isys_queue_to_video(aq);
+			spin_lock_irqsave(&aq->lock, flags);
+			list_del(&ib->head);
+			if (op_flags & IPU_ISYS_BUFFER_LIST_FL_ACTIVE)
+				list_add(&ib->head, &aq->active);
+			else if (op_flags & IPU_ISYS_BUFFER_LIST_FL_INCOMING)
+				list_add_tail(&ib->head, &aq->incoming);
+			spin_unlock_irqrestore(&aq->lock, flags);
+
+			if (op_flags & IPU_ISYS_BUFFER_LIST_FL_SET_STATE)
+				vb2_buffer_done(vb, state);
+		} else if (ib->type == IPU_ISYS_SHORT_PACKET_BUFFER) {
+			struct ipu_isys_private_buffer *pb =
+			    ipu_isys_buffer_to_private_buffer(ib);
+			struct ipu_isys_pipeline *ip = pb->ip;
+
+			av = container_of(ip, struct ipu_isys_video, ip);
+			spin_lock_irqsave(&ip->short_packet_queue_lock, flags);
+			list_del(&ib->head);
+			if (op_flags & IPU_ISYS_BUFFER_LIST_FL_ACTIVE)
+				list_add(&ib->head, &ip->short_packet_active);
+			else if (op_flags & IPU_ISYS_BUFFER_LIST_FL_INCOMING)
+				list_add(&ib->head, &ip->short_packet_incoming);
+			spin_unlock_irqrestore(&ip->short_packet_queue_lock,
+					       flags);
+		} else {
+			WARN_ON(1);
+			return;
+		}
+
+		if (first) {
+			dev_dbg(&av->isys->adev->dev,
+				"queue buf list %p flags %lx, s %d, %d bufs\n",
+				bl, op_flags, state, bl->nbufs);
+			first = false;
+		}
+
+		bl->nbufs--;
+	}
+
+	WARN_ON(bl->nbufs);
+}
+
+/*
+ * flush_firmware_streamon_fail() - Flush in cases where requests may
+ * have been queued to firmware and the *firmware streamon fails for a
+ * reason or another.
+ */
+static void flush_firmware_streamon_fail(struct ipu_isys_pipeline *ip)
+{
+	struct ipu_isys_video *pipe_av =
+	    container_of(ip, struct ipu_isys_video, ip);
+	struct ipu_isys_queue *aq;
+	unsigned long flags;
+
+	lockdep_assert_held(&pipe_av->mutex);
+
+	list_for_each_entry(aq, &ip->queues, node) {
+		struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+		struct ipu_isys_buffer *ib, *ib_safe;
+
+		spin_lock_irqsave(&aq->lock, flags);
+		list_for_each_entry_safe(ib, ib_safe, &aq->active, head) {
+			struct vb2_buffer *vb =
+			    ipu_isys_buffer_to_vb2_buffer(ib);
+
+			list_del(&ib->head);
+			if (av->streaming) {
+				dev_dbg(&av->isys->adev->dev,
+					"%s: queue buffer %u back to incoming\n",
+					av->vdev.name,
+					vb->index);
+				/* Queue already streaming, return to driver. */
+				list_add(&ib->head, &aq->incoming);
+				continue;
+			}
+			/* Queue not yet streaming, return to user. */
+			dev_dbg(&av->isys->adev->dev,
+				"%s: return %u back to videobuf2\n",
+				av->vdev.name,
+				vb->index);
+			vb2_buffer_done(ipu_isys_buffer_to_vb2_buffer(ib),
+					VB2_BUF_STATE_QUEUED);
+		}
+		spin_unlock_irqrestore(&aq->lock, flags);
+	}
+}
+
+/*
+ * Attempt obtaining a buffer list from the incoming queues, a list of
+ * buffers that contains one entry from each video buffer queue. If
+ * all queues have no buffers, the buffers that were already dequeued
+ * are returned to their queues.
+ */
+static int buffer_list_get(struct ipu_isys_pipeline *ip,
+			   struct ipu_isys_buffer_list *bl)
+{
+	struct ipu_isys_queue *aq;
+	struct ipu_isys_buffer *ib;
+	unsigned long flags;
+	int ret = 0;
+
+	bl->nbufs = 0;
+	INIT_LIST_HEAD(&bl->head);
+
+	list_for_each_entry(aq, &ip->queues, node) {
+		struct ipu_isys_buffer *ib;
+
+		spin_lock_irqsave(&aq->lock, flags);
+		if (list_empty(&aq->incoming)) {
+			spin_unlock_irqrestore(&aq->lock, flags);
+			ret = -ENODATA;
+			goto error;
+		}
+
+		ib = list_last_entry(&aq->incoming,
+				     struct ipu_isys_buffer, head);
+		if (ib->req) {
+			spin_unlock_irqrestore(&aq->lock, flags);
+			ret = -ENODATA;
+			goto error;
+		}
+
+		dev_dbg(&ip->isys->adev->dev, "buffer: %s: buffer %u\n",
+			ipu_isys_queue_to_video(aq)->vdev.name,
+			ipu_isys_buffer_to_vb2_buffer(ib)->index
+		    );
+		list_del(&ib->head);
+		list_add(&ib->head, &bl->head);
+		spin_unlock_irqrestore(&aq->lock, flags);
+
+		bl->nbufs++;
+	}
+
+	list_for_each_entry(ib, &bl->head, head) {
+		struct vb2_buffer *vb = ipu_isys_buffer_to_vb2_buffer(ib);
+
+		aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+		if (aq->prepare_frame_buff_set)
+			aq->prepare_frame_buff_set(vb);
+	}
+
+	/* Get short packet buffer. */
+	if (ip->interlaced && ip->isys->short_packet_source ==
+	    IPU_ISYS_SHORT_PACKET_FROM_RECEIVER) {
+		ib = ipu_isys_csi2_get_short_packet_buffer(ip, bl);
+		if (!ib) {
+			ret = -ENODATA;
+			dev_err(&ip->isys->adev->dev,
+				"No more short packet buffers. Driver bug?");
+			WARN_ON(1);
+			goto error;
+		}
+		bl->nbufs++;
+	}
+
+	dev_dbg(&ip->isys->adev->dev, "get buffer list %p, %u buffers\n", bl,
+		bl->nbufs);
+	return ret;
+
+error:
+	if (!list_empty(&bl->head))
+		ipu_isys_buffer_list_queue(bl,
+					   IPU_ISYS_BUFFER_LIST_FL_INCOMING, 0);
+	return ret;
+}
+
+void
+ipu_isys_buffer_to_fw_frame_buff_pin(struct vb2_buffer *vb,
+				     struct ipu_fw_isys_frame_buff_set_abi *set)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = container_of(aq, struct ipu_isys_video, aq);
+
+	if (av->compression)
+		set->output_pins[aq->fw_output].compress = 1;
+
+	set->output_pins[aq->fw_output].addr =
+	    vb2_dma_contig_plane_dma_addr(vb, 0);
+	set->output_pins[aq->fw_output].out_buf_id =
+	    vb->index + 1;
+}
+
+/*
+ * Convert a buffer list to a isys fw ABI framebuffer set. The
+ * buffer list is not modified.
+ */
+#define IPU_ISYS_FRAME_NUM_THRESHOLD  (30)
+void
+ipu_isys_buffer_to_fw_frame_buff(struct ipu_fw_isys_frame_buff_set_abi *set,
+				 struct ipu_isys_pipeline *ip,
+				 struct ipu_isys_buffer_list *bl)
+{
+	struct ipu_isys_buffer *ib;
+
+	WARN_ON(!bl->nbufs);
+
+	set->send_irq_sof = 1;
+	set->send_resp_sof = 1;
+	set->send_irq_eof = 0;
+	set->send_resp_eof = 0;
+
+	if (ip->streaming)
+		set->send_irq_capture_ack = 0;
+	else
+		set->send_irq_capture_ack = 1;
+	set->send_irq_capture_done = 0;
+
+	set->send_resp_capture_ack = 1;
+	set->send_resp_capture_done = 1;
+	if (!ip->interlaced &&
+	    atomic_read(&ip->sequence) >= IPU_ISYS_FRAME_NUM_THRESHOLD) {
+		set->send_resp_capture_ack = 0;
+		set->send_resp_capture_done = 0;
+	}
+
+	list_for_each_entry(ib, &bl->head, head) {
+		if (ib->type == IPU_ISYS_VIDEO_BUFFER) {
+			struct vb2_buffer *vb =
+			    ipu_isys_buffer_to_vb2_buffer(ib);
+			struct ipu_isys_queue *aq =
+			    vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+
+			if (aq->fill_frame_buff_set_pin)
+				aq->fill_frame_buff_set_pin(vb, set);
+		} else if (ib->type == IPU_ISYS_SHORT_PACKET_BUFFER) {
+			struct ipu_isys_private_buffer *pb =
+			    ipu_isys_buffer_to_private_buffer(ib);
+			struct ipu_fw_isys_output_pin_payload_abi *output_pin =
+			    &set->output_pins[ip->short_packet_output_pin];
+
+			output_pin->addr = pb->dma_addr;
+			output_pin->out_buf_id = pb->index + 1;
+		} else {
+			WARN_ON(1);
+		}
+	}
+}
+
+/* Start streaming for real. The buffer list must be available. */
+static int ipu_isys_stream_start(struct ipu_isys_pipeline *ip,
+				 struct ipu_isys_buffer_list *bl, bool error)
+{
+	struct ipu_isys_video *pipe_av =
+	    container_of(ip, struct ipu_isys_video, ip);
+	struct ipu_isys_buffer_list __bl;
+	int rval;
+
+	mutex_lock(&pipe_av->isys->stream_mutex);
+
+	rval = ipu_isys_video_set_streaming(pipe_av, 1, bl);
+	if (rval) {
+		mutex_unlock(&pipe_av->isys->stream_mutex);
+		goto out_requeue;
+	}
+
+	ip->streaming = 1;
+
+	mutex_unlock(&pipe_av->isys->stream_mutex);
+
+	bl = &__bl;
+
+	do {
+		struct ipu_fw_isys_frame_buff_set_abi *buf = NULL;
+		struct isys_fw_msgs *msg;
+		enum ipu_fw_isys_send_type send_type =
+		    IPU_FW_ISYS_SEND_TYPE_STREAM_CAPTURE;
+
+		rval = buffer_list_get(ip, bl);
+		if (rval == -EINVAL)
+			goto out_requeue;
+		else if (rval < 0)
+			break;
+
+		msg = ipu_get_fw_msg_buf(ip);
+		if (!msg)
+			return -ENOMEM;
+
+		buf = to_frame_msg_buf(msg);
+
+		ipu_isys_buffer_to_fw_frame_buff(buf, ip, bl);
+
+		ipu_fw_isys_dump_frame_buff_set(&pipe_av->isys->adev->dev, buf,
+						ip->nr_output_pins);
+
+		ipu_isys_buffer_list_queue(bl,
+					   IPU_ISYS_BUFFER_LIST_FL_ACTIVE, 0);
+
+		rval = ipu_fw_isys_complex_cmd(pipe_av->isys,
+					       ip->stream_handle,
+					       buf, to_dma_addr(msg),
+					       sizeof(*buf),
+					       send_type);
+		ipu_put_fw_mgs_buf(pipe_av->isys, (uintptr_t)buf);
+	} while (!WARN_ON(rval));
+
+	return 0;
+
+out_requeue:
+	if (bl && bl->nbufs)
+		ipu_isys_buffer_list_queue(bl,
+					   IPU_ISYS_BUFFER_LIST_FL_INCOMING |
+					   (error ?
+					    IPU_ISYS_BUFFER_LIST_FL_SET_STATE :
+					    0),
+					   error ? VB2_BUF_STATE_ERROR :
+					   VB2_BUF_STATE_QUEUED);
+	flush_firmware_streamon_fail(ip);
+
+	return rval;
+}
+
+static void __buf_queue(struct vb2_buffer *vb, bool force)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	struct ipu_isys_buffer *ib = vb2_buffer_to_ipu_isys_buffer(vb);
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct ipu_isys_buffer_list bl;
+
+	struct ipu_fw_isys_frame_buff_set_abi *buf = NULL;
+	struct isys_fw_msgs *msg;
+
+	struct ipu_isys_video *pipe_av =
+	    container_of(ip, struct ipu_isys_video, ip);
+	unsigned long flags;
+	unsigned int i;
+	int rval;
+
+	dev_dbg(&av->isys->adev->dev, "buffer: %s: buf_queue %u\n",
+		av->vdev.name,
+		vb->index
+	    );
+
+	for (i = 0; i < vb->num_planes; i++)
+		dev_dbg(&av->isys->adev->dev, "iova: plane %u iova 0x%x\n", i,
+			(u32)vb2_dma_contig_plane_dma_addr(vb, i));
+
+	spin_lock_irqsave(&aq->lock, flags);
+	list_add(&ib->head, &aq->incoming);
+	spin_unlock_irqrestore(&aq->lock, flags);
+
+	if (ib->req)
+		return;
+
+	if (!pipe_av || !vb->vb2_queue->streaming) {
+		dev_dbg(&av->isys->adev->dev,
+			"not pipe_av set, adding to incoming\n");
+		return;
+	}
+
+	mutex_unlock(&av->mutex);
+	mutex_lock(&pipe_av->mutex);
+
+	if (!force && ip->nr_streaming != ip->nr_queues) {
+		dev_dbg(&av->isys->adev->dev,
+			"not streaming yet, adding to incoming\n");
+		goto out;
+	}
+
+	/*
+	 * We just put one buffer to the incoming list of this queue
+	 * (above). Let's see whether all queues in the pipeline would
+	 * have a buffer.
+	 */
+	rval = buffer_list_get(ip, &bl);
+	if (rval < 0) {
+		if (rval == -EINVAL) {
+			dev_err(&av->isys->adev->dev,
+				"error: should not happen\n");
+			WARN_ON(1);
+		} else {
+			dev_dbg(&av->isys->adev->dev,
+				"not enough buffers available\n");
+		}
+		goto out;
+	}
+
+	msg = ipu_get_fw_msg_buf(ip);
+	if (!msg) {
+		rval = -ENOMEM;
+		goto out;
+	}
+	buf = to_frame_msg_buf(msg);
+
+	ipu_isys_buffer_to_fw_frame_buff(buf, ip, &bl);
+
+	ipu_fw_isys_dump_frame_buff_set(&pipe_av->isys->adev->dev, buf,
+					ip->nr_output_pins);
+
+	if (!ip->streaming) {
+		dev_dbg(&av->isys->adev->dev,
+			"got a buffer to start streaming!\n");
+		rval = ipu_isys_stream_start(ip, &bl, true);
+		if (rval)
+			dev_err(&av->isys->adev->dev,
+				"stream start failed.\n");
+		goto out;
+	}
+
+	/*
+	 * We must queue the buffers in the buffer list to the
+	 * appropriate video buffer queues BEFORE passing them to the
+	 * firmware since we could get a buffer event back before we
+	 * have queued them ourselves to the active queue.
+	 */
+	ipu_isys_buffer_list_queue(&bl, IPU_ISYS_BUFFER_LIST_FL_ACTIVE, 0);
+
+	rval = ipu_fw_isys_complex_cmd(pipe_av->isys,
+				       ip->stream_handle,
+				       buf, to_dma_addr(msg),
+				       sizeof(*buf),
+				       IPU_FW_ISYS_SEND_TYPE_STREAM_CAPTURE);
+	ipu_put_fw_mgs_buf(pipe_av->isys, (uintptr_t)buf);
+	if (!WARN_ON(rval < 0))
+		dev_dbg(&av->isys->adev->dev, "queued buffer\n");
+
+out:
+	mutex_unlock(&pipe_av->mutex);
+	mutex_lock(&av->mutex);
+}
+
+static void buf_queue(struct vb2_buffer *vb)
+{
+	__buf_queue(vb, false);
+}
+
+int ipu_isys_link_fmt_validate(struct ipu_isys_queue *aq)
+{
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	struct v4l2_subdev_format fmt = { 0 };
+	struct media_pad *pad = media_entity_remote_pad(av->vdev.entity.pads);
+	struct v4l2_subdev *sd;
+	int rval;
+
+	if (!pad) {
+		dev_dbg(&av->isys->adev->dev,
+			"video node %s pad not connected\n", av->vdev.name);
+		return -ENOTCONN;
+	}
+
+	sd = media_entity_to_v4l2_subdev(pad->entity);
+
+	fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	fmt.pad = pad->index;
+	rval = v4l2_subdev_call(sd, pad, get_fmt, NULL, &fmt);
+	if (rval)
+		return rval;
+
+	if (fmt.format.width != av->mpix.width ||
+	    fmt.format.height != av->mpix.height) {
+		dev_dbg(&av->isys->adev->dev,
+			"wrong width or height %ux%u (%ux%u expected)\n",
+			av->mpix.width, av->mpix.height,
+			fmt.format.width, fmt.format.height);
+		return -EINVAL;
+	}
+
+	if (fmt.format.field != av->mpix.field) {
+		dev_dbg(&av->isys->adev->dev,
+			"wrong field value 0x%8.8x (0x%8.8x expected)\n",
+			av->mpix.field, fmt.format.field);
+		return -EINVAL;
+	}
+
+	if (fmt.format.code != av->pfmt->code) {
+		dev_dbg(&av->isys->adev->dev,
+			"wrong media bus code 0x%8.8x (0x%8.8x expected)\n",
+			av->pfmt->code, fmt.format.code);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/* Return buffers back to videobuf2. */
+static void return_buffers(struct ipu_isys_queue *aq,
+			   enum vb2_buffer_state state)
+{
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	int reset_needed = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&aq->lock, flags);
+	while (!list_empty(&aq->incoming)) {
+		struct ipu_isys_buffer *ib = list_first_entry(&aq->incoming,
+							      struct
+							      ipu_isys_buffer,
+							      head);
+		struct vb2_buffer *vb = ipu_isys_buffer_to_vb2_buffer(ib);
+
+		list_del(&ib->head);
+		spin_unlock_irqrestore(&aq->lock, flags);
+
+		vb2_buffer_done(vb, state);
+
+		dev_dbg(&av->isys->adev->dev,
+			"%s: stop_streaming incoming %u\n",
+			ipu_isys_queue_to_video(vb2_queue_to_ipu_isys_queue
+						(vb->vb2_queue))->vdev.name,
+			vb->index);
+
+		spin_lock_irqsave(&aq->lock, flags);
+	}
+
+	/*
+	 * Something went wrong (FW crash / HW hang / not all buffers
+	 * returned from isys) if there are still buffers queued in active
+	 * queue. We have to clean up places a bit.
+	 */
+	while (!list_empty(&aq->active)) {
+		struct ipu_isys_buffer *ib = list_first_entry(&aq->active,
+							      struct
+							      ipu_isys_buffer,
+							      head);
+		struct vb2_buffer *vb = ipu_isys_buffer_to_vb2_buffer(ib);
+
+		list_del(&ib->head);
+		spin_unlock_irqrestore(&aq->lock, flags);
+
+		vb2_buffer_done(vb, state);
+
+		dev_warn(&av->isys->adev->dev, "%s: cleaning active queue %u\n",
+			 ipu_isys_queue_to_video(vb2_queue_to_ipu_isys_queue
+						 (vb->vb2_queue))->vdev.name,
+			 vb->index);
+
+		spin_lock_irqsave(&aq->lock, flags);
+		reset_needed = 1;
+	}
+
+	spin_unlock_irqrestore(&aq->lock, flags);
+
+	if (reset_needed) {
+		mutex_lock(&av->isys->mutex);
+		av->isys->reset_needed = true;
+		mutex_unlock(&av->isys->mutex);
+	}
+}
+
+static int start_streaming(struct vb2_queue *q, unsigned int count)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(q);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	struct ipu_isys_video *pipe_av;
+	struct ipu_isys_pipeline *ip;
+	struct ipu_isys_buffer_list __bl, *bl = NULL;
+	bool first;
+	int rval;
+
+	dev_dbg(&av->isys->adev->dev,
+		"stream: %s: width %u, height %u, css pixelformat %u\n",
+		av->vdev.name, av->mpix.width, av->mpix.height,
+		av->pfmt->css_pixelformat);
+
+	mutex_lock(&av->isys->stream_mutex);
+
+	first = !av->vdev.entity.pipe;
+
+	if (first) {
+		rval = ipu_isys_video_prepare_streaming(av, 1);
+		if (rval)
+			goto out_return_buffers;
+	}
+
+	mutex_unlock(&av->isys->stream_mutex);
+
+	rval = aq->link_fmt_validate(aq);
+	if (rval) {
+		dev_dbg(&av->isys->adev->dev,
+			"%s: link format validation failed (%d)\n",
+			av->vdev.name, rval);
+		goto out_unprepare_streaming;
+	}
+
+	ip = to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	pipe_av = container_of(ip, struct ipu_isys_video, ip);
+	mutex_unlock(&av->mutex);
+
+	mutex_lock(&pipe_av->mutex);
+	ip->nr_streaming++;
+	dev_dbg(&av->isys->adev->dev, "queue %u of %u\n", ip->nr_streaming,
+		ip->nr_queues);
+	list_add(&aq->node, &ip->queues);
+	if (ip->nr_streaming != ip->nr_queues)
+		goto out;
+
+	if (list_empty(&av->isys->requests)) {
+		bl = &__bl;
+		rval = buffer_list_get(ip, bl);
+		if (rval == -EINVAL) {
+			goto out_stream_start;
+		} else if (rval < 0) {
+			dev_dbg(&av->isys->adev->dev,
+				"no request available, postponing streamon\n");
+			goto out;
+		}
+	}
+
+	rval = ipu_isys_stream_start(ip, bl, false);
+	if (rval)
+		goto out_stream_start;
+
+out:
+	mutex_unlock(&pipe_av->mutex);
+	mutex_lock(&av->mutex);
+
+	return 0;
+
+out_stream_start:
+	list_del(&aq->node);
+	ip->nr_streaming--;
+	mutex_unlock(&pipe_av->mutex);
+	mutex_lock(&av->mutex);
+
+out_unprepare_streaming:
+	mutex_lock(&av->isys->stream_mutex);
+	if (first)
+		ipu_isys_video_prepare_streaming(av, 0);
+
+out_return_buffers:
+	mutex_unlock(&av->isys->stream_mutex);
+	return_buffers(aq, VB2_BUF_STATE_QUEUED);
+
+	return rval;
+}
+
+static void stop_streaming(struct vb2_queue *q)
+{
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(q);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct ipu_isys_video *pipe_av =
+	    container_of(ip, struct ipu_isys_video, ip);
+
+	if (pipe_av != av) {
+		mutex_unlock(&av->mutex);
+		mutex_lock(&pipe_av->mutex);
+	}
+
+	mutex_lock(&av->isys->stream_mutex);
+	if (ip->nr_streaming == ip->nr_queues && ip->streaming)
+		ipu_isys_video_set_streaming(av, 0, NULL);
+	if (ip->nr_streaming == 1)
+		ipu_isys_video_prepare_streaming(av, 0);
+	mutex_unlock(&av->isys->stream_mutex);
+
+	ip->nr_streaming--;
+	list_del(&aq->node);
+	ip->streaming = 0;
+
+	if (pipe_av != av) {
+		mutex_unlock(&pipe_av->mutex);
+		mutex_lock(&av->mutex);
+	}
+
+	return_buffers(aq, VB2_BUF_STATE_ERROR);
+}
+
+static unsigned int
+get_sof_sequence_by_timestamp(struct ipu_isys_pipeline *ip,
+			      struct ipu_fw_isys_resp_info_abi *info)
+{
+	struct ipu_isys *isys =
+	    container_of(ip, struct ipu_isys_video, ip)->isys;
+	u64 time = (u64)info->timestamp[1] << 32 | info->timestamp[0];
+	unsigned int i;
+
+	/*
+	 * The timestamp is invalid as no TSC in some FPGA platform,
+	 * so get the sequence from pipeline directly in this case.
+	 */
+	if (time == 0)
+		return atomic_read(&ip->sequence) - 1;
+
+	for (i = 0; i < IPU_ISYS_MAX_PARALLEL_SOF; i++)
+		if (time == ip->seq[i].timestamp) {
+			dev_dbg(&isys->adev->dev,
+				"sof: using seq nr %u for ts 0x%16.16llx\n",
+				ip->seq[i].sequence, time);
+			return ip->seq[i].sequence;
+		}
+
+	dev_dbg(&isys->adev->dev, "SOF: looking for 0x%16.16llx\n", time);
+	for (i = 0; i < IPU_ISYS_MAX_PARALLEL_SOF; i++)
+		dev_dbg(&isys->adev->dev,
+			"SOF: sequence %u, timestamp value 0x%16.16llx\n",
+			ip->seq[i].sequence, ip->seq[i].timestamp);
+	dev_dbg(&isys->adev->dev, "SOF sequence number not found\n");
+
+	return 0;
+}
+
+static u64 get_sof_ns_delta(struct ipu_isys_video *av,
+			    struct ipu_fw_isys_resp_info_abi *info)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(&av->isys->adev->dev);
+	struct ipu_device *isp = adev->isp;
+	u64 delta, tsc_now;
+
+	if (!ipu_buttress_tsc_read(isp, &tsc_now))
+		delta = tsc_now -
+		    ((u64)info->timestamp[1] << 32 | info->timestamp[0]);
+	else
+		delta = 0;
+
+	return ipu_buttress_tsc_ticks_to_ns(delta, isp);
+}
+
+void
+ipu_isys_buf_calc_sequence_time(struct ipu_isys_buffer *ib,
+				struct ipu_fw_isys_resp_info_abi *info)
+{
+	struct vb2_buffer *vb = ipu_isys_buffer_to_vb2_buffer(ib);
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+	struct ipu_isys_queue *aq = vb2_queue_to_ipu_isys_queue(vb->vb2_queue);
+	struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+	struct device *dev = &av->isys->adev->dev;
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	u64 ns;
+	u32 sequence;
+
+	if (ip->has_sof) {
+		ns = (wall_clock_ts_on) ? ktime_get_real_ns() : ktime_get_ns();
+		ns -= get_sof_ns_delta(av, info);
+		sequence = get_sof_sequence_by_timestamp(ip, info);
+	} else {
+		ns = ((wall_clock_ts_on) ? ktime_get_real_ns() :
+		      ktime_get_ns());
+		sequence = (atomic_inc_return(&ip->sequence) - 1)
+		    / ip->nr_queues;
+	}
+
+	vbuf->vb2_buf.timestamp = ns;
+	vbuf->sequence = sequence;
+
+	dev_dbg(dev, "buf: %s: buffer done, CPU-timestamp:%lld, sequence:%d\n",
+		av->vdev.name, ktime_get_ns(), sequence);
+	dev_dbg(dev, "index:%d, vbuf timestamp:%lld, endl\n",
+		vb->index, vbuf->vb2_buf.timestamp);
+}
+
+void ipu_isys_queue_buf_done(struct ipu_isys_buffer *ib)
+{
+	struct vb2_buffer *vb = ipu_isys_buffer_to_vb2_buffer(ib);
+
+	if (atomic_read(&ib->str2mmio_flag)) {
+		vb2_buffer_done(vb, VB2_BUF_STATE_ERROR);
+		/*
+		 * Operation on buffer is ended with error and will be reported
+		 * to the userspace when it is de-queued
+		 */
+		atomic_set(&ib->str2mmio_flag, 0);
+	} else {
+		vb2_buffer_done(vb, VB2_BUF_STATE_DONE);
+	}
+}
+
+void ipu_isys_queue_buf_ready(struct ipu_isys_pipeline *ip,
+			      struct ipu_fw_isys_resp_info_abi *info)
+{
+	struct ipu_isys *isys =
+	    container_of(ip, struct ipu_isys_video, ip)->isys;
+	struct ipu_isys_queue *aq = ip->output_pins[info->pin_id].aq;
+	struct ipu_isys_buffer *ib;
+	struct vb2_buffer *vb;
+	unsigned long flags;
+	bool first = true;
+	struct vb2_v4l2_buffer *buf;
+
+	dev_dbg(&isys->adev->dev, "buffer: %s: received buffer %8.8x\n",
+		ipu_isys_queue_to_video(aq)->vdev.name, info->pin.addr);
+
+	spin_lock_irqsave(&aq->lock, flags);
+	if (list_empty(&aq->active)) {
+		spin_unlock_irqrestore(&aq->lock, flags);
+		dev_err(&isys->adev->dev, "active queue empty\n");
+		return;
+	}
+
+	list_for_each_entry_reverse(ib, &aq->active, head) {
+		dma_addr_t addr;
+
+		vb = ipu_isys_buffer_to_vb2_buffer(ib);
+		addr = vb2_dma_contig_plane_dma_addr(vb, 0);
+
+		if (info->pin.addr != addr) {
+			if (first)
+				dev_err(&isys->adev->dev,
+					"WARN: buffer address %pad expected!\n",
+					&addr);
+			first = false;
+			continue;
+		}
+
+		if (info->error_info.error ==
+		    IPU_FW_ISYS_ERROR_HW_REPORTED_STR2MMIO) {
+			/*
+			 * Check for error message:
+			 * 'IPU_FW_ISYS_ERROR_HW_REPORTED_STR2MMIO'
+			 */
+			atomic_set(&ib->str2mmio_flag, 1);
+		}
+		dev_dbg(&isys->adev->dev, "buffer: found buffer %pad\n", &addr);
+
+		buf = to_vb2_v4l2_buffer(vb);
+		buf->field = V4L2_FIELD_NONE;
+
+		list_del(&ib->head);
+		spin_unlock_irqrestore(&aq->lock, flags);
+
+		ipu_isys_buf_calc_sequence_time(ib, info);
+
+		/*
+		 * For interlaced buffers, the notification to user space
+		 * is postponed to capture_done event since the field
+		 * information is available only at that time.
+		 */
+		if (ip->interlaced) {
+			spin_lock_irqsave(&ip->short_packet_queue_lock, flags);
+			list_add(&ib->head, &ip->pending_interlaced_bufs);
+			spin_unlock_irqrestore(&ip->short_packet_queue_lock,
+					       flags);
+		} else {
+			ipu_isys_queue_buf_done(ib);
+		}
+
+		return;
+	}
+
+	dev_err(&isys->adev->dev,
+		"WARNING: cannot find a matching video buffer!\n");
+
+	spin_unlock_irqrestore(&aq->lock, flags);
+}
+
+void
+ipu_isys_queue_short_packet_ready(struct ipu_isys_pipeline *ip,
+				  struct ipu_fw_isys_resp_info_abi *info)
+{
+	struct ipu_isys *isys =
+	    container_of(ip, struct ipu_isys_video, ip)->isys;
+	unsigned long flags;
+
+	dev_dbg(&isys->adev->dev, "receive short packet buffer %8.8x\n",
+		info->pin.addr);
+	spin_lock_irqsave(&ip->short_packet_queue_lock, flags);
+	ip->cur_field = ipu_isys_csi2_get_current_field(ip, info->timestamp);
+	spin_unlock_irqrestore(&ip->short_packet_queue_lock, flags);
+}
+
+struct vb2_ops ipu_isys_queue_ops = {
+	.queue_setup = queue_setup,
+	.wait_prepare = ipu_isys_queue_unlock,
+	.wait_finish = ipu_isys_queue_lock,
+	.buf_init = buf_init,
+	.buf_prepare = buf_prepare,
+	.buf_finish = buf_finish,
+	.buf_cleanup = buf_cleanup,
+	.start_streaming = start_streaming,
+	.stop_streaming = stop_streaming,
+	.buf_queue = buf_queue,
+};
+
+int ipu_isys_queue_init(struct ipu_isys_queue *aq)
+{
+	struct ipu_isys *isys = ipu_isys_queue_to_video(aq)->isys;
+	int rval;
+
+	if (!aq->vbq.io_modes)
+		aq->vbq.io_modes = VB2_USERPTR | VB2_MMAP | VB2_DMABUF;
+	aq->vbq.drv_priv = aq;
+	aq->vbq.ops = &ipu_isys_queue_ops;
+	aq->vbq.mem_ops = &vb2_dma_contig_memops;
+	aq->vbq.timestamp_flags = (wall_clock_ts_on) ?
+	    V4L2_BUF_FLAG_TIMESTAMP_UNKNOWN : V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+
+	rval = vb2_queue_init(&aq->vbq);
+	if (rval)
+		return rval;
+
+	aq->dev = &isys->adev->dev;
+	aq->vbq.dev = &isys->adev->dev;
+	spin_lock_init(&aq->lock);
+	INIT_LIST_HEAD(&aq->active);
+	INIT_LIST_HEAD(&aq->incoming);
+
+	return 0;
+}
+
+void ipu_isys_queue_cleanup(struct ipu_isys_queue *aq)
+{
+	vb2_queue_release(&aq->vbq);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-queue.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-queue.h
@@ -0,0 +1,142 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_QUEUE_H
+#define IPU_ISYS_QUEUE_H
+
+#include <linux/list.h>
+#include <linux/spinlock.h>
+
+#include <media/videobuf2-v4l2.h>
+
+#include "ipu-isys-media.h"
+
+struct ipu_isys_video;
+struct ipu_isys_pipeline;
+struct ipu_fw_isys_resp_info_abi;
+struct ipu_fw_isys_frame_buff_set_abi;
+
+enum ipu_isys_buffer_type {
+	IPU_ISYS_VIDEO_BUFFER,
+	IPU_ISYS_SHORT_PACKET_BUFFER,
+};
+
+struct ipu_isys_queue {
+	struct list_head node;	/* struct ipu_isys_pipeline.queues */
+	struct vb2_queue vbq;
+	struct device *dev;
+	/*
+	 * @lock: serialise access to queued and pre_streamon_queued
+	 */
+	spinlock_t lock;
+	struct list_head active;
+	struct list_head incoming;
+	u32 css_pin_type;
+	unsigned int fw_output;
+	int (*buf_init)(struct vb2_buffer *vb);
+	void (*buf_cleanup)(struct vb2_buffer *vb);
+	int (*buf_prepare)(struct vb2_buffer *vb);
+	void (*prepare_frame_buff_set)(struct vb2_buffer *vb);
+	void (*fill_frame_buff_set_pin)(struct vb2_buffer *vb,
+					struct ipu_fw_isys_frame_buff_set_abi *
+					set);
+	int (*link_fmt_validate)(struct ipu_isys_queue *aq);
+};
+
+struct ipu_isys_buffer {
+	struct list_head head;
+	enum ipu_isys_buffer_type type;
+	struct list_head req_head;
+	struct media_device_request *req;
+	atomic_t str2mmio_flag;
+};
+
+struct ipu_isys_video_buffer {
+	struct vb2_v4l2_buffer vb_v4l2;
+	struct ipu_isys_buffer ib;
+};
+
+struct ipu_isys_private_buffer {
+	struct ipu_isys_buffer ib;
+	struct ipu_isys_pipeline *ip;
+	unsigned int index;
+	unsigned int bytesused;
+	dma_addr_t dma_addr;
+	void *buffer;
+};
+
+#define IPU_ISYS_BUFFER_LIST_FL_INCOMING	BIT(0)
+#define IPU_ISYS_BUFFER_LIST_FL_ACTIVE	BIT(1)
+#define IPU_ISYS_BUFFER_LIST_FL_SET_STATE	BIT(2)
+
+struct ipu_isys_buffer_list {
+	struct list_head head;
+	unsigned int nbufs;
+};
+
+#define vb2_queue_to_ipu_isys_queue(__vb2) \
+	container_of(__vb2, struct ipu_isys_queue, vbq)
+
+#define ipu_isys_to_isys_video_buffer(__ib) \
+	container_of(__ib, struct ipu_isys_video_buffer, ib)
+
+#define vb2_buffer_to_ipu_isys_video_buffer(__vb) \
+	container_of(to_vb2_v4l2_buffer(__vb), \
+	struct ipu_isys_video_buffer, vb_v4l2)
+
+#define ipu_isys_buffer_to_vb2_buffer(__ib) \
+	(&ipu_isys_to_isys_video_buffer(__ib)->vb_v4l2.vb2_buf)
+
+#define vb2_buffer_to_ipu_isys_buffer(__vb) \
+	(&vb2_buffer_to_ipu_isys_video_buffer(__vb)->ib)
+
+#define ipu_isys_buffer_to_private_buffer(__ib) \
+	container_of(__ib, struct ipu_isys_private_buffer, ib)
+
+struct ipu_isys_request {
+	struct media_device_request req;
+	/* serialise access to buffers */
+	spinlock_t lock;
+	struct list_head buffers;	/* struct ipu_isys_buffer.head */
+	bool dispatched;
+	/*
+	 * struct ipu_isys.requests;
+	 * struct ipu_isys_pipeline.struct.*
+	 */
+	struct list_head head;
+};
+
+#define to_ipu_isys_request(__req) \
+	container_of(__req, struct ipu_isys_request, req)
+
+int ipu_isys_buf_prepare(struct vb2_buffer *vb);
+
+void ipu_isys_buffer_list_queue(struct ipu_isys_buffer_list *bl,
+				unsigned long op_flags,
+				enum vb2_buffer_state state);
+struct ipu_isys_request *
+ipu_isys_next_queued_request(struct ipu_isys_pipeline *ip);
+void
+ipu_isys_buffer_to_fw_frame_buff_pin(struct vb2_buffer *vb,
+				     struct ipu_fw_isys_frame_buff_set_abi *
+				     set);
+void
+ipu_isys_buffer_to_fw_frame_buff(struct ipu_fw_isys_frame_buff_set_abi *set,
+				 struct ipu_isys_pipeline *ip,
+				 struct ipu_isys_buffer_list *bl);
+int ipu_isys_link_fmt_validate(struct ipu_isys_queue *aq);
+
+void
+ipu_isys_buf_calc_sequence_time(struct ipu_isys_buffer *ib,
+				struct ipu_fw_isys_resp_info_abi *info);
+void ipu_isys_queue_buf_done(struct ipu_isys_buffer *ib);
+void ipu_isys_queue_buf_ready(struct ipu_isys_pipeline *ip,
+			      struct ipu_fw_isys_resp_info_abi *info);
+void
+ipu_isys_queue_short_packet_ready(struct ipu_isys_pipeline *ip,
+				  struct ipu_fw_isys_resp_info_abi *inf);
+
+int ipu_isys_queue_init(struct ipu_isys_queue *aq);
+void ipu_isys_queue_cleanup(struct ipu_isys_queue *aq);
+
+#endif /* IPU_ISYS_QUEUE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-subdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-subdev.c
@@ -0,0 +1,650 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/types.h>
+#include <linux/videodev2.h>
+
+#include <media/media-entity.h>
+
+#include <uapi/linux/media-bus-format.h>
+
+#include "ipu-isys.h"
+#include "ipu-isys-video.h"
+#include "ipu-isys-subdev.h"
+
+unsigned int ipu_isys_mbus_code_to_bpp(u32 code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		return 24;
+	case MEDIA_BUS_FMT_YUYV10_1X20:
+		return 20;
+	case MEDIA_BUS_FMT_Y10_1X10:
+	case MEDIA_BUS_FMT_RGB565_1X16:
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_YUYV8_1X16:
+		return 16;
+	case MEDIA_BUS_FMT_SBGGR12_1X12:
+	case MEDIA_BUS_FMT_SGBRG12_1X12:
+	case MEDIA_BUS_FMT_SGRBG12_1X12:
+	case MEDIA_BUS_FMT_SRGGB12_1X12:
+		return 12;
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+		return 10;
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+	case MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8:
+		return 8;
+	default:
+		WARN_ON(1);
+		return -EINVAL;
+	}
+}
+
+unsigned int ipu_isys_mbus_code_to_mipi(u32 code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_RGB565_1X16:
+		return IPU_ISYS_MIPI_CSI2_TYPE_RGB565;
+	case MEDIA_BUS_FMT_RGB888_1X24:
+		return IPU_ISYS_MIPI_CSI2_TYPE_RGB888;
+	case MEDIA_BUS_FMT_YUYV10_1X20:
+		return IPU_ISYS_MIPI_CSI2_TYPE_YUV422_10;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_YUYV8_1X16:
+		return IPU_ISYS_MIPI_CSI2_TYPE_YUV422_8;
+	case MEDIA_BUS_FMT_SBGGR12_1X12:
+	case MEDIA_BUS_FMT_SGBRG12_1X12:
+	case MEDIA_BUS_FMT_SGRBG12_1X12:
+	case MEDIA_BUS_FMT_SRGGB12_1X12:
+		return IPU_ISYS_MIPI_CSI2_TYPE_RAW12;
+	case MEDIA_BUS_FMT_Y10_1X10:
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+		return IPU_ISYS_MIPI_CSI2_TYPE_RAW10;
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+		return IPU_ISYS_MIPI_CSI2_TYPE_RAW8;
+	case MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8:
+		return IPU_ISYS_MIPI_CSI2_TYPE_USER_DEF(1);
+	default:
+		WARN_ON(1);
+		return -EINVAL;
+	}
+}
+
+enum ipu_isys_subdev_pixelorder ipu_isys_subdev_get_pixelorder(u32 code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_SBGGR12_1X12:
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+	case MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8:
+		return IPU_ISYS_SUBDEV_PIXELORDER_BGGR;
+	case MEDIA_BUS_FMT_SGBRG12_1X12:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8:
+		return IPU_ISYS_SUBDEV_PIXELORDER_GBRG;
+	case MEDIA_BUS_FMT_SGRBG12_1X12:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8:
+		return IPU_ISYS_SUBDEV_PIXELORDER_GRBG;
+	case MEDIA_BUS_FMT_SRGGB12_1X12:
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+	case MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8:
+		return IPU_ISYS_SUBDEV_PIXELORDER_RGGB;
+	default:
+		WARN_ON(1);
+		return -EINVAL;
+	}
+}
+
+u32 ipu_isys_subdev_code_to_uncompressed(u32 sink_code)
+{
+	switch (sink_code) {
+	case MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8:
+		return MEDIA_BUS_FMT_SBGGR10_1X10;
+	case MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8:
+		return MEDIA_BUS_FMT_SGBRG10_1X10;
+	case MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8:
+		return MEDIA_BUS_FMT_SGRBG10_1X10;
+	case MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8:
+		return MEDIA_BUS_FMT_SRGGB10_1X10;
+	default:
+		return sink_code;
+	}
+}
+
+struct v4l2_mbus_framefmt *__ipu_isys_get_ffmt(struct v4l2_subdev *sd,
+					       struct v4l2_subdev_state *sd_state,
+					       unsigned int pad,
+					       unsigned int which)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+
+	if (which == V4L2_SUBDEV_FORMAT_ACTIVE)
+		return &asd->ffmt[pad];
+	else
+		return v4l2_subdev_get_try_format(sd, sd_state, pad);
+}
+
+struct v4l2_rect *__ipu_isys_get_selection(struct v4l2_subdev *sd,
+					   struct v4l2_subdev_state *sd_state,
+					   unsigned int target,
+					   unsigned int pad, unsigned int which)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+
+	if (which == V4L2_SUBDEV_FORMAT_ACTIVE) {
+		switch (target) {
+		case V4L2_SEL_TGT_CROP:
+			return &asd->crop[pad];
+		case V4L2_SEL_TGT_COMPOSE:
+			return &asd->compose[pad];
+		}
+	} else {
+		switch (target) {
+		case V4L2_SEL_TGT_CROP:
+			return v4l2_subdev_get_try_crop(sd, sd_state, pad);
+		case V4L2_SEL_TGT_COMPOSE:
+			return v4l2_subdev_get_try_compose(sd, sd_state, pad);
+		}
+	}
+	WARN_ON(1);
+	return NULL;
+}
+
+static int target_valid(struct v4l2_subdev *sd, unsigned int target,
+			unsigned int pad)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+
+	switch (target) {
+	case V4L2_SEL_TGT_CROP:
+		return asd->valid_tgts[pad].crop;
+	case V4L2_SEL_TGT_COMPOSE:
+		return asd->valid_tgts[pad].compose;
+	default:
+		return 0;
+	}
+}
+
+int ipu_isys_subdev_fmt_propagate(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_mbus_framefmt *ffmt,
+				  struct v4l2_rect *r,
+				  enum isys_subdev_prop_tgt tgt,
+				  unsigned int pad, unsigned int which)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	struct v4l2_mbus_framefmt **ffmts = NULL;
+	struct v4l2_rect **crops = NULL;
+	struct v4l2_rect **compose = NULL;
+	unsigned int i;
+	int rval = 0;
+
+	if (tgt == IPU_ISYS_SUBDEV_PROP_TGT_NR_OF)
+		return 0;
+
+	if (WARN_ON(pad >= sd->entity.num_pads))
+		return -EINVAL;
+
+	ffmts = kcalloc(sd->entity.num_pads,
+			sizeof(*ffmts), GFP_KERNEL);
+	if (!ffmts) {
+		rval = -ENOMEM;
+		goto out_subdev_fmt_propagate;
+	}
+	crops = kcalloc(sd->entity.num_pads,
+			sizeof(*crops), GFP_KERNEL);
+	if (!crops) {
+		rval = -ENOMEM;
+		goto out_subdev_fmt_propagate;
+	}
+	compose = kcalloc(sd->entity.num_pads,
+			  sizeof(*compose), GFP_KERNEL);
+	if (!compose) {
+		rval = -ENOMEM;
+		goto out_subdev_fmt_propagate;
+	}
+
+	for (i = 0; i < sd->entity.num_pads; i++) {
+		ffmts[i] = __ipu_isys_get_ffmt(sd, sd_state, i, which);
+		crops[i] = __ipu_isys_get_selection(sd, sd_state,
+						    V4L2_SEL_TGT_CROP, i, which);
+		compose[i] = __ipu_isys_get_selection(sd, sd_state,
+						      V4L2_SEL_TGT_COMPOSE, i, which);
+	}
+
+	switch (tgt) {
+	case IPU_ISYS_SUBDEV_PROP_TGT_SINK_FMT:
+		crops[pad]->left = 0;
+		crops[pad]->top = 0;
+		crops[pad]->width = ffmt->width;
+		crops[pad]->height = ffmt->height;
+		rval = ipu_isys_subdev_fmt_propagate(sd, sd_state, ffmt,
+						     crops[pad], tgt + 1, pad, which);
+		goto out_subdev_fmt_propagate;
+	case IPU_ISYS_SUBDEV_PROP_TGT_SINK_CROP:
+		if (WARN_ON(sd->entity.pads[pad].flags & MEDIA_PAD_FL_SOURCE))
+			goto out_subdev_fmt_propagate;
+
+		compose[pad]->left = 0;
+		compose[pad]->top = 0;
+		compose[pad]->width = r->width;
+		compose[pad]->height = r->height;
+		rval = ipu_isys_subdev_fmt_propagate(sd, sd_state, ffmt,
+						     compose[pad], tgt + 1, pad, which);
+		goto out_subdev_fmt_propagate;
+	case IPU_ISYS_SUBDEV_PROP_TGT_SINK_COMPOSE:
+		if (WARN_ON(sd->entity.pads[pad].flags & MEDIA_PAD_FL_SOURCE)) {
+			rval = -EINVAL;
+			goto out_subdev_fmt_propagate;
+		}
+
+		for (i = 1; i < sd->entity.num_pads; i++) {
+			if (!(sd->entity.pads[i].flags &
+					MEDIA_PAD_FL_SOURCE))
+				continue;
+
+			compose[i]->left = 0;
+			compose[i]->top = 0;
+			compose[i]->width = r->width;
+			compose[i]->height = r->height;
+			rval = ipu_isys_subdev_fmt_propagate(sd, sd_state,
+							ffmt, compose[i], tgt + 1, i, which);
+			if (rval)
+				goto out_subdev_fmt_propagate;
+		}
+		goto out_subdev_fmt_propagate;
+	case IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_COMPOSE:
+		if (WARN_ON(sd->entity.pads[pad].flags & MEDIA_PAD_FL_SINK)) {
+			rval = -EINVAL;
+			goto out_subdev_fmt_propagate;
+		}
+
+		crops[pad]->left = 0;
+		crops[pad]->top = 0;
+		crops[pad]->width = r->width;
+		crops[pad]->height = r->height;
+		rval = ipu_isys_subdev_fmt_propagate(sd, sd_state, ffmt,
+						     crops[pad], tgt + 1, pad, which);
+		goto out_subdev_fmt_propagate;
+	case IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_CROP:{
+			struct v4l2_subdev_format fmt = {
+				.which = which,
+				.pad = pad,
+				.format = {
+					.width = r->width,
+					.height = r->height,
+					/*
+					 * Either use the code from sink pad
+					 * or the current one.
+					 */
+					.code = ffmt ? ffmt->code :
+						       ffmts[pad]->code,
+					.field = ffmt ? ffmt->field :
+							ffmts[pad]->field,
+				},
+			};
+
+			asd->set_ffmt(sd, sd_state, &fmt);
+			goto out_subdev_fmt_propagate;
+		}
+	}
+
+out_subdev_fmt_propagate:
+	kfree(ffmts);
+	kfree(crops);
+	kfree(compose);
+	return rval;
+}
+
+int ipu_isys_subdev_set_ffmt_default(struct v4l2_subdev *sd,
+				     struct v4l2_subdev_state *sd_state,
+				     struct v4l2_subdev_format *fmt)
+{
+	struct v4l2_mbus_framefmt *ffmt =
+		__ipu_isys_get_ffmt(sd, sd_state, fmt->pad, fmt->which);
+
+	/* No propagation for non-zero pads. */
+	if (fmt->pad) {
+		struct v4l2_mbus_framefmt *sink_ffmt =
+			__ipu_isys_get_ffmt(sd, sd_state, 0, fmt->which);
+
+		ffmt->width = sink_ffmt->width;
+		ffmt->height = sink_ffmt->height;
+		ffmt->code = sink_ffmt->code;
+		ffmt->field = sink_ffmt->field;
+
+		return 0;
+	}
+
+	ffmt->width = fmt->format.width;
+	ffmt->height = fmt->format.height;
+	ffmt->code = fmt->format.code;
+	ffmt->field = fmt->format.field;
+
+	return ipu_isys_subdev_fmt_propagate(sd, sd_state, &fmt->format, NULL,
+					     IPU_ISYS_SUBDEV_PROP_TGT_SINK_FMT,
+					     fmt->pad, fmt->which);
+}
+
+int __ipu_isys_subdev_set_ffmt(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_format *fmt)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	struct v4l2_mbus_framefmt *ffmt =
+		__ipu_isys_get_ffmt(sd, sd_state, fmt->pad, fmt->which);
+	u32 code = asd->supported_codes[fmt->pad][0];
+	unsigned int i;
+
+	WARN_ON(!mutex_is_locked(&asd->mutex));
+
+	fmt->format.width = clamp(fmt->format.width, IPU_ISYS_MIN_WIDTH,
+				  IPU_ISYS_MAX_WIDTH);
+	fmt->format.height = clamp(fmt->format.height,
+				   IPU_ISYS_MIN_HEIGHT, IPU_ISYS_MAX_HEIGHT);
+
+	for (i = 0; asd->supported_codes[fmt->pad][i]; i++) {
+		if (asd->supported_codes[fmt->pad][i] == fmt->format.code) {
+			code = asd->supported_codes[fmt->pad][i];
+			break;
+		}
+	}
+
+	fmt->format.code = code;
+
+	asd->set_ffmt(sd, sd_state, fmt);
+
+	fmt->format = *ffmt;
+
+	return 0;
+}
+
+int ipu_isys_subdev_set_ffmt(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	int rval;
+
+	mutex_lock(&asd->mutex);
+	rval = __ipu_isys_subdev_set_ffmt(sd, sd_state, fmt);
+	mutex_unlock(&asd->mutex);
+
+	return rval;
+}
+
+int ipu_isys_subdev_get_ffmt(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+
+	mutex_lock(&asd->mutex);
+	fmt->format = *__ipu_isys_get_ffmt(sd, sd_state, fmt->pad,
+					   fmt->which);
+	mutex_unlock(&asd->mutex);
+
+	return 0;
+}
+
+int ipu_isys_subdev_set_sel(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_selection *sel)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	struct media_pad *pad = &asd->sd.entity.pads[sel->pad];
+	struct v4l2_rect *r, __r = { 0 };
+	unsigned int tgt;
+
+	if (!target_valid(sd, sel->target, sel->pad))
+		return -EINVAL;
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		if (pad->flags & MEDIA_PAD_FL_SINK) {
+			struct v4l2_mbus_framefmt *ffmt =
+				__ipu_isys_get_ffmt(sd, sd_state, sel->pad,
+						    sel->which);
+
+			__r.width = ffmt->width;
+			__r.height = ffmt->height;
+			r = &__r;
+			tgt = IPU_ISYS_SUBDEV_PROP_TGT_SINK_CROP;
+		} else {
+			/* 0 is the sink pad. */
+			r = __ipu_isys_get_selection(sd, sd_state, sel->target, 0,
+						     sel->which);
+			tgt = IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_CROP;
+		}
+
+		break;
+	case V4L2_SEL_TGT_COMPOSE:
+		if (pad->flags & MEDIA_PAD_FL_SINK) {
+			r = __ipu_isys_get_selection(sd, sd_state, V4L2_SEL_TGT_CROP,
+						     sel->pad, sel->which);
+			tgt = IPU_ISYS_SUBDEV_PROP_TGT_SINK_COMPOSE;
+		} else {
+			r = __ipu_isys_get_selection(sd, sd_state,
+						     V4L2_SEL_TGT_COMPOSE, 0,
+						     sel->which);
+			tgt = IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_COMPOSE;
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	sel->r.width = clamp(sel->r.width, IPU_ISYS_MIN_WIDTH, r->width);
+	sel->r.height = clamp(sel->r.height, IPU_ISYS_MIN_HEIGHT, r->height);
+	*__ipu_isys_get_selection(sd, sd_state, sel->target, sel->pad,
+				  sel->which) = sel->r;
+	return ipu_isys_subdev_fmt_propagate(sd, sd_state, NULL, &sel->r, tgt,
+					     sel->pad, sel->which);
+}
+
+int ipu_isys_subdev_get_sel(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_selection *sel)
+{
+	if (!target_valid(sd, sel->target, sel->pad))
+		return -EINVAL;
+
+	sel->r = *__ipu_isys_get_selection(sd, sd_state, sel->target,
+					   sel->pad, sel->which);
+
+	return 0;
+}
+
+int ipu_isys_subdev_enum_mbus_code(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	const u32 *supported_codes = asd->supported_codes[code->pad];
+	u32 index;
+
+	for (index = 0; supported_codes[index]; index++) {
+		if (index == code->index) {
+			code->code = supported_codes[index];
+			return 0;
+		}
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * Besides validating the link, figure out the external pad and the
+ * ISYS FW ABI source.
+ */
+int ipu_isys_subdev_link_validate(struct v4l2_subdev *sd,
+				  struct media_link *link,
+				  struct v4l2_subdev_format *source_fmt,
+				  struct v4l2_subdev_format *sink_fmt)
+{
+	struct v4l2_subdev *source_sd =
+	    media_entity_to_v4l2_subdev(link->source->entity);
+	struct ipu_isys_pipeline *ip = container_of(sd->entity.pipe,
+						    struct ipu_isys_pipeline,
+						    pipe);
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+
+	if (!source_sd)
+		return -ENODEV;
+	if (strncmp(source_sd->name, IPU_ISYS_ENTITY_PREFIX,
+		    strlen(IPU_ISYS_ENTITY_PREFIX)) != 0) {
+		/*
+		 * source_sd isn't ours --- sd must be the external
+		 * sub-device.
+		 */
+		ip->external = link->source;
+		ip->source = to_ipu_isys_subdev(sd)->source;
+		dev_dbg(&asd->isys->adev->dev, "%s: using source %d\n",
+			sd->entity.name, ip->source);
+	} else if (source_sd->entity.num_pads == 1) {
+		/* All internal sources have a single pad. */
+		ip->external = link->source;
+		ip->source = to_ipu_isys_subdev(source_sd)->source;
+
+		dev_dbg(&asd->isys->adev->dev, "%s: using source %d\n",
+			sd->entity.name, ip->source);
+	}
+
+	if (asd->isl_mode != IPU_ISL_OFF)
+		ip->isl_mode = asd->isl_mode;
+
+	return v4l2_subdev_link_validate_default(sd, link, source_fmt,
+						 sink_fmt);
+}
+
+int ipu_isys_subdev_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	struct ipu_isys_subdev *asd = to_ipu_isys_subdev(sd);
+	unsigned int i;
+
+	mutex_lock(&asd->mutex);
+
+	for (i = 0; i < asd->sd.entity.num_pads; i++) {
+		struct v4l2_mbus_framefmt *try_fmt =
+			v4l2_subdev_get_try_format(sd, fh->state, i);
+		struct v4l2_rect *try_crop =
+			v4l2_subdev_get_try_crop(sd, fh->state, i);
+		struct v4l2_rect *try_compose =
+			v4l2_subdev_get_try_compose(sd, fh->state, i);
+
+		*try_fmt = asd->ffmt[i];
+		*try_crop = asd->crop[i];
+		*try_compose = asd->compose[i];
+	}
+
+	mutex_unlock(&asd->mutex);
+
+	return 0;
+}
+
+int ipu_isys_subdev_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+int ipu_isys_subdev_init(struct ipu_isys_subdev *asd,
+			 struct v4l2_subdev_ops *ops,
+			 unsigned int nr_ctrls,
+			 unsigned int num_pads,
+			 unsigned int num_source,
+			 unsigned int num_sink,
+			 unsigned int sd_flags)
+{
+	int rval = -EINVAL;
+
+	mutex_init(&asd->mutex);
+
+	v4l2_subdev_init(&asd->sd, ops);
+
+	asd->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | sd_flags;
+	asd->sd.owner = THIS_MODULE;
+	asd->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+
+	asd->nsources = num_source;
+	asd->nsinks = num_sink;
+
+	asd->pad = devm_kcalloc(&asd->isys->adev->dev, num_pads,
+				sizeof(*asd->pad), GFP_KERNEL);
+
+	asd->ffmt = devm_kcalloc(&asd->isys->adev->dev, num_pads,
+				 sizeof(*asd->ffmt), GFP_KERNEL);
+
+	asd->crop = devm_kcalloc(&asd->isys->adev->dev, num_pads,
+				 sizeof(*asd->crop), GFP_KERNEL);
+
+	asd->compose = devm_kcalloc(&asd->isys->adev->dev, num_pads,
+				    sizeof(*asd->compose), GFP_KERNEL);
+
+	asd->valid_tgts = devm_kcalloc(&asd->isys->adev->dev, num_pads,
+				       sizeof(*asd->valid_tgts), GFP_KERNEL);
+	if (!asd->pad || !asd->ffmt || !asd->crop || !asd->compose ||
+	    !asd->valid_tgts)
+		return -ENOMEM;
+
+	rval = media_entity_pads_init(&asd->sd.entity, num_pads, asd->pad);
+	if (rval)
+		goto out_mutex_destroy;
+
+	if (asd->ctrl_init) {
+		rval = v4l2_ctrl_handler_init(&asd->ctrl_handler, nr_ctrls);
+		if (rval)
+			goto out_media_entity_cleanup;
+
+		asd->ctrl_init(&asd->sd);
+		if (asd->ctrl_handler.error) {
+			rval = asd->ctrl_handler.error;
+			goto out_v4l2_ctrl_handler_free;
+		}
+
+		asd->sd.ctrl_handler = &asd->ctrl_handler;
+	}
+
+	asd->source = -1;
+
+	return 0;
+
+out_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(&asd->ctrl_handler);
+
+out_media_entity_cleanup:
+	media_entity_cleanup(&asd->sd.entity);
+
+out_mutex_destroy:
+	mutex_destroy(&asd->mutex);
+
+	return rval;
+}
+
+void ipu_isys_subdev_cleanup(struct ipu_isys_subdev *asd)
+{
+	media_entity_cleanup(&asd->sd.entity);
+	v4l2_ctrl_handler_free(&asd->ctrl_handler);
+	mutex_destroy(&asd->mutex);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-subdev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-subdev.h
@@ -0,0 +1,152 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_SUBDEV_H
+#define IPU_ISYS_SUBDEV_H
+
+#include <linux/mutex.h>
+
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ctrls.h>
+
+#include "ipu-isys-queue.h"
+
+#define IPU_ISYS_MIPI_CSI2_TYPE_NULL	0x10
+#define IPU_ISYS_MIPI_CSI2_TYPE_BLANKING	0x11
+#define IPU_ISYS_MIPI_CSI2_TYPE_EMBEDDED8	0x12
+#define IPU_ISYS_MIPI_CSI2_TYPE_YUV422_8	0x1e
+#define IPU_ISYS_MIPI_CSI2_TYPE_YUV422_10	0x1f
+#define IPU_ISYS_MIPI_CSI2_TYPE_RGB565	0x22
+#define IPU_ISYS_MIPI_CSI2_TYPE_RGB888	0x24
+#define IPU_ISYS_MIPI_CSI2_TYPE_RAW6	0x28
+#define IPU_ISYS_MIPI_CSI2_TYPE_RAW7	0x29
+#define IPU_ISYS_MIPI_CSI2_TYPE_RAW8	0x2a
+#define IPU_ISYS_MIPI_CSI2_TYPE_RAW10	0x2b
+#define IPU_ISYS_MIPI_CSI2_TYPE_RAW12	0x2c
+#define IPU_ISYS_MIPI_CSI2_TYPE_RAW14	0x2d
+/* 1-8 */
+#define IPU_ISYS_MIPI_CSI2_TYPE_USER_DEF(i)	(0x30 + (i) - 1)
+
+#define FMT_ENTRY (struct ipu_isys_fmt_entry [])
+
+enum isys_subdev_prop_tgt {
+	IPU_ISYS_SUBDEV_PROP_TGT_SINK_FMT,
+	IPU_ISYS_SUBDEV_PROP_TGT_SINK_CROP,
+	IPU_ISYS_SUBDEV_PROP_TGT_SINK_COMPOSE,
+	IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_COMPOSE,
+	IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_CROP,
+};
+
+#define	IPU_ISYS_SUBDEV_PROP_TGT_NR_OF \
+	(IPU_ISYS_SUBDEV_PROP_TGT_SOURCE_CROP + 1)
+
+enum ipu_isl_mode {
+	IPU_ISL_OFF = 0,	/* SOC BE */
+	IPU_ISL_CSI2_BE,	/* RAW BE */
+};
+
+enum ipu_be_mode {
+	IPU_BE_RAW = 0,
+	IPU_BE_SOC
+};
+
+enum ipu_isys_subdev_pixelorder {
+	IPU_ISYS_SUBDEV_PIXELORDER_BGGR = 0,
+	IPU_ISYS_SUBDEV_PIXELORDER_GBRG,
+	IPU_ISYS_SUBDEV_PIXELORDER_GRBG,
+	IPU_ISYS_SUBDEV_PIXELORDER_RGGB,
+};
+
+struct ipu_isys;
+
+struct ipu_isys_subdev {
+	/* Serialise access to any other field in the struct */
+	struct mutex mutex;
+	struct v4l2_subdev sd;
+	struct ipu_isys *isys;
+	u32 const *const *supported_codes;
+	struct media_pad *pad;
+	struct v4l2_mbus_framefmt *ffmt;
+	struct v4l2_rect *crop;
+	struct v4l2_rect *compose;
+	unsigned int nsinks;
+	unsigned int nsources;
+	struct v4l2_ctrl_handler ctrl_handler;
+	void (*ctrl_init)(struct v4l2_subdev *sd);
+	void (*set_ffmt)(struct v4l2_subdev *sd,
+			 struct v4l2_subdev_state *sd_state,
+			 struct v4l2_subdev_format *fmt);
+	struct {
+		bool crop;
+		bool compose;
+	} *valid_tgts;
+	enum ipu_isl_mode isl_mode;
+	enum ipu_be_mode be_mode;
+	int source;	/* SSI stream source; -1 if unset */
+};
+
+#define to_ipu_isys_subdev(__sd) \
+	container_of(__sd, struct ipu_isys_subdev, sd)
+
+struct v4l2_mbus_framefmt *__ipu_isys_get_ffmt(struct v4l2_subdev *sd,
+					       struct v4l2_subdev_state *sd_state,
+					       unsigned int pad,
+					       unsigned int which);
+
+unsigned int ipu_isys_mbus_code_to_bpp(u32 code);
+unsigned int ipu_isys_mbus_code_to_mipi(u32 code);
+u32 ipu_isys_subdev_code_to_uncompressed(u32 sink_code);
+
+enum ipu_isys_subdev_pixelorder ipu_isys_subdev_get_pixelorder(u32 code);
+
+int ipu_isys_subdev_fmt_propagate(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_mbus_framefmt *ffmt,
+				  struct v4l2_rect *r,
+				  enum isys_subdev_prop_tgt tgt,
+				  unsigned int pad, unsigned int which);
+
+int ipu_isys_subdev_set_ffmt_default(struct v4l2_subdev *sd,
+				     struct v4l2_subdev_state *sd_state,
+				     struct v4l2_subdev_format *fmt);
+int __ipu_isys_subdev_set_ffmt(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_format *fmt);
+struct v4l2_rect *__ipu_isys_get_selection(struct v4l2_subdev *sd,
+					   struct v4l2_subdev_state *sd_state,
+					   unsigned int target,
+					   unsigned int pad,
+					   unsigned int which);
+int ipu_isys_subdev_set_ffmt(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt);
+int ipu_isys_subdev_get_ffmt(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt);
+int ipu_isys_subdev_get_sel(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_selection *sel);
+int ipu_isys_subdev_set_sel(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_selection *sel);
+int ipu_isys_subdev_enum_mbus_code(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_mbus_code_enum
+				   *code);
+int ipu_isys_subdev_link_validate(struct v4l2_subdev *sd,
+				  struct media_link *link,
+				  struct v4l2_subdev_format *source_fmt,
+				  struct v4l2_subdev_format *sink_fmt);
+
+int ipu_isys_subdev_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh);
+int ipu_isys_subdev_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh);
+int ipu_isys_subdev_init(struct ipu_isys_subdev *asd,
+			 struct v4l2_subdev_ops *ops,
+			 unsigned int nr_ctrls,
+			 unsigned int num_pads,
+			 unsigned int num_source,
+			 unsigned int num_sink,
+			 unsigned int sd_flags);
+void ipu_isys_subdev_cleanup(struct ipu_isys_subdev *asd);
+#endif /* IPU_ISYS_SUBDEV_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-tpg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-tpg.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/device.h>
+#include <linux/module.h>
+
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-isys.h"
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-tpg.h"
+#include "ipu-isys-video.h"
+#include "ipu-platform-isys-csi2-reg.h"
+
+static const u32 tpg_supported_codes_pad[] = {
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	0,
+};
+
+static const u32 *tpg_supported_codes[] = {
+	tpg_supported_codes_pad,
+};
+
+static struct v4l2_subdev_internal_ops tpg_sd_internal_ops = {
+	.open = ipu_isys_subdev_open,
+	.close = ipu_isys_subdev_close,
+};
+
+static const struct v4l2_subdev_video_ops tpg_sd_video_ops = {
+	.s_stream = tpg_set_stream,
+};
+
+static int ipu_isys_tpg_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ipu_isys_tpg *tpg = container_of(container_of(ctrl->handler,
+							     struct
+							     ipu_isys_subdev,
+							     ctrl_handler),
+						struct ipu_isys_tpg, asd);
+
+	switch (ctrl->id) {
+	case V4L2_CID_HBLANK:
+		writel(ctrl->val, tpg->base + MIPI_GEN_REG_SYNG_HBLANK_CYC);
+		break;
+	case V4L2_CID_VBLANK:
+		writel(ctrl->val, tpg->base + MIPI_GEN_REG_SYNG_VBLANK_CYC);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		writel(ctrl->val, tpg->base + MIPI_GEN_REG_TPG_MODE);
+		break;
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops ipu_isys_tpg_ctrl_ops = {
+	.s_ctrl = ipu_isys_tpg_s_ctrl,
+};
+
+static s64 ipu_isys_tpg_rate(struct ipu_isys_tpg *tpg, unsigned int bpp)
+{
+	return MIPI_GEN_PPC * IPU_ISYS_FREQ / bpp;
+}
+
+static const char *const tpg_mode_items[] = {
+	"Ramp",
+	"Checkerboard",	/* Does not work, disabled. */
+	"Frame Based Colour",
+};
+
+static struct v4l2_ctrl_config tpg_mode = {
+	.ops = &ipu_isys_tpg_ctrl_ops,
+	.id = V4L2_CID_TEST_PATTERN,
+	.name = "Test Pattern",
+	.type = V4L2_CTRL_TYPE_MENU,
+	.min = 0,
+	.max = ARRAY_SIZE(tpg_mode_items) - 1,
+	.def = 0,
+	.menu_skip_mask = 0x2,
+	.qmenu = tpg_mode_items,
+};
+
+static const struct v4l2_ctrl_config csi2_header_cfg = {
+	.id = V4L2_CID_IPU_STORE_CSI2_HEADER,
+	.name = "Store CSI-2 Headers",
+	.type = V4L2_CTRL_TYPE_BOOLEAN,
+	.min = 0,
+	.max = 1,
+	.step = 1,
+	.def = 1,
+};
+
+static void ipu_isys_tpg_init_controls(struct v4l2_subdev *sd)
+{
+	struct ipu_isys_tpg *tpg = to_ipu_isys_tpg(sd);
+	int hblank;
+	u64 default_pixel_rate;
+
+	hblank = 1024;
+
+	tpg->hblank = v4l2_ctrl_new_std(&tpg->asd.ctrl_handler,
+					&ipu_isys_tpg_ctrl_ops,
+					V4L2_CID_HBLANK, 8, 65535, 1, hblank);
+
+	tpg->vblank = v4l2_ctrl_new_std(&tpg->asd.ctrl_handler,
+					&ipu_isys_tpg_ctrl_ops,
+					V4L2_CID_VBLANK, 8, 65535, 1, 1024);
+
+	default_pixel_rate = ipu_isys_tpg_rate(tpg, 8);
+	tpg->pixel_rate = v4l2_ctrl_new_std(&tpg->asd.ctrl_handler,
+					    &ipu_isys_tpg_ctrl_ops,
+					    V4L2_CID_PIXEL_RATE,
+					    default_pixel_rate,
+					    default_pixel_rate,
+					    1, default_pixel_rate);
+	if (tpg->pixel_rate) {
+		tpg->pixel_rate->cur.val = default_pixel_rate;
+		tpg->pixel_rate->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	}
+
+	v4l2_ctrl_new_custom(&tpg->asd.ctrl_handler, &tpg_mode, NULL);
+	tpg->store_csi2_header =
+		v4l2_ctrl_new_custom(&tpg->asd.ctrl_handler,
+				     &csi2_header_cfg, NULL);
+}
+
+static void tpg_set_ffmt(struct v4l2_subdev *sd,
+			 struct v4l2_subdev_state *sd_state,
+			 struct v4l2_subdev_format *fmt)
+{
+	fmt->format.field = V4L2_FIELD_NONE;
+	*__ipu_isys_get_ffmt(sd, sd_state, fmt->pad, fmt->which) = fmt->format;
+}
+
+static int ipu_isys_tpg_set_ffmt(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct ipu_isys_tpg *tpg = to_ipu_isys_tpg(sd);
+	__u32 code = tpg->asd.ffmt[TPG_PAD_SOURCE].code;
+	unsigned int bpp = ipu_isys_mbus_code_to_bpp(code);
+	s64 tpg_rate = ipu_isys_tpg_rate(tpg, bpp);
+	int rval;
+
+	mutex_lock(&tpg->asd.mutex);
+	rval = __ipu_isys_subdev_set_ffmt(sd, sd_state, fmt);
+	mutex_unlock(&tpg->asd.mutex);
+
+	if (rval || fmt->which != V4L2_SUBDEV_FORMAT_ACTIVE)
+		return rval;
+
+	v4l2_ctrl_s_ctrl_int64(tpg->pixel_rate, tpg_rate);
+
+	return 0;
+}
+
+static const struct ipu_isys_pixelformat *
+ipu_isys_tpg_try_fmt(struct ipu_isys_video *av,
+		     struct v4l2_pix_format_mplane *mpix)
+{
+	struct media_link *link = list_first_entry(&av->vdev.entity.links,
+						   struct media_link, list);
+	struct v4l2_subdev *sd =
+		media_entity_to_v4l2_subdev(link->source->entity);
+	struct ipu_isys_tpg *tpg;
+
+	if (!sd)
+		return NULL;
+
+	tpg = to_ipu_isys_tpg(sd);
+
+	return ipu_isys_video_try_fmt_vid_mplane(av, mpix,
+		v4l2_ctrl_g_ctrl(tpg->store_csi2_header));
+}
+
+static const struct v4l2_subdev_pad_ops tpg_sd_pad_ops = {
+	.get_fmt = ipu_isys_subdev_get_ffmt,
+	.set_fmt = ipu_isys_tpg_set_ffmt,
+	.enum_mbus_code = ipu_isys_subdev_enum_mbus_code,
+};
+
+static int subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+			   struct v4l2_event_subscription *sub)
+{
+	switch (sub->type) {
+#ifdef IPU_TPG_FRAME_SYNC
+	case V4L2_EVENT_FRAME_SYNC:
+		return v4l2_event_subscribe(fh, sub, 10, NULL);
+#endif
+	case V4L2_EVENT_CTRL:
+		return v4l2_ctrl_subscribe_event(fh, sub);
+	default:
+		return -EINVAL;
+	}
+};
+
+/* V4L2 subdev core operations */
+static const struct v4l2_subdev_core_ops tpg_sd_core_ops = {
+	.subscribe_event = subscribe_event,
+	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static struct v4l2_subdev_ops tpg_sd_ops = {
+	.core = &tpg_sd_core_ops,
+	.video = &tpg_sd_video_ops,
+	.pad = &tpg_sd_pad_ops,
+};
+
+static struct media_entity_operations tpg_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+void ipu_isys_tpg_cleanup(struct ipu_isys_tpg *tpg)
+{
+	v4l2_device_unregister_subdev(&tpg->asd.sd);
+	ipu_isys_subdev_cleanup(&tpg->asd);
+	ipu_isys_video_cleanup(&tpg->av);
+}
+
+int ipu_isys_tpg_init(struct ipu_isys_tpg *tpg,
+		      struct ipu_isys *isys,
+		      void __iomem *base, void __iomem *sel,
+		      unsigned int index)
+{
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.pad = TPG_PAD_SOURCE,
+		.format = {
+			   .width = 4096,
+			   .height = 3072,
+			   },
+	};
+	int rval;
+
+	tpg->isys = isys;
+	tpg->base = base;
+	tpg->sel = sel;
+	tpg->index = index;
+
+	tpg->asd.sd.entity.ops = &tpg_entity_ops;
+	tpg->asd.ctrl_init = ipu_isys_tpg_init_controls;
+	tpg->asd.isys = isys;
+
+	rval = ipu_isys_subdev_init(&tpg->asd, &tpg_sd_ops, 5,
+				    NR_OF_TPG_PADS,
+				    NR_OF_TPG_SOURCE_PADS,
+				    NR_OF_TPG_SINK_PADS,
+				    V4L2_SUBDEV_FL_HAS_EVENTS);
+	if (rval)
+		return rval;
+
+	tpg->asd.sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	tpg->asd.pad[TPG_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	tpg->asd.source = IPU_FW_ISYS_STREAM_SRC_MIPIGEN_PORT0 + index;
+	tpg->asd.supported_codes = tpg_supported_codes;
+	tpg->asd.set_ffmt = tpg_set_ffmt;
+	ipu_isys_subdev_set_ffmt(&tpg->asd.sd, NULL, &fmt);
+
+	tpg->asd.sd.internal_ops = &tpg_sd_internal_ops;
+	snprintf(tpg->asd.sd.name, sizeof(tpg->asd.sd.name),
+		 IPU_ISYS_ENTITY_PREFIX " TPG %u", index);
+	v4l2_set_subdevdata(&tpg->asd.sd, &tpg->asd);
+	rval = v4l2_device_register_subdev(&isys->v4l2_dev, &tpg->asd.sd);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't register v4l2 subdev\n");
+		goto fail;
+	}
+
+	snprintf(tpg->av.vdev.name, sizeof(tpg->av.vdev.name),
+		 IPU_ISYS_ENTITY_PREFIX " TPG %u capture", index);
+	tpg->av.isys = isys;
+	tpg->av.aq.css_pin_type = IPU_FW_ISYS_PIN_TYPE_MIPI;
+	tpg->av.pfmts = ipu_isys_pfmts_packed;
+	tpg->av.try_fmt_vid_mplane = ipu_isys_tpg_try_fmt;
+	tpg->av.prepare_fw_stream =
+	    ipu_isys_prepare_fw_cfg_default;
+	tpg->av.packed = true;
+	tpg->av.line_header_length = IPU_ISYS_CSI2_LONG_PACKET_HEADER_SIZE;
+	tpg->av.line_footer_length = IPU_ISYS_CSI2_LONG_PACKET_FOOTER_SIZE;
+	tpg->av.aq.buf_prepare = ipu_isys_buf_prepare;
+	tpg->av.aq.fill_frame_buff_set_pin =
+	    ipu_isys_buffer_to_fw_frame_buff_pin;
+	tpg->av.aq.link_fmt_validate = ipu_isys_link_fmt_validate;
+	tpg->av.aq.vbq.buf_struct_size = sizeof(struct ipu_isys_video_buffer);
+
+	rval = ipu_isys_video_init(&tpg->av, &tpg->asd.sd.entity,
+				   TPG_PAD_SOURCE, MEDIA_PAD_FL_SINK, 0);
+	if (rval) {
+		dev_info(&isys->adev->dev, "can't init video node\n");
+		goto fail;
+	}
+
+	return 0;
+
+fail:
+	ipu_isys_tpg_cleanup(tpg);
+
+	return rval;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-tpg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-tpg.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_TPG_H
+#define IPU_ISYS_TPG_H
+
+#include <media/media-entity.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+
+#include "ipu-isys-subdev.h"
+#include "ipu-isys-video.h"
+#include "ipu-isys-queue.h"
+
+struct ipu_isys_tpg_pdata;
+struct ipu_isys;
+
+#define TPG_PAD_SOURCE			0
+#define NR_OF_TPG_PADS			1
+#define NR_OF_TPG_SOURCE_PADS		1
+#define NR_OF_TPG_SINK_PADS		0
+#define NR_OF_TPG_STREAMS		1
+
+/*
+ * PPC is 4 pixels for clock for RAW8, RAW10 and RAW12.
+ * Source: FW validation test code.
+ */
+#define MIPI_GEN_PPC		4
+
+#define MIPI_GEN_REG_COM_ENABLE				0x0
+#define MIPI_GEN_REG_COM_DTYPE				0x4
+/* RAW8, RAW10 or RAW12 */
+#define MIPI_GEN_COM_DTYPE_RAW(n)			(((n) - 8) / 2)
+#define MIPI_GEN_REG_COM_VTYPE				0x8
+#define MIPI_GEN_REG_COM_VCHAN				0xc
+#define MIPI_GEN_REG_COM_WCOUNT				0x10
+#define MIPI_GEN_REG_PRBS_RSTVAL0			0x14
+#define MIPI_GEN_REG_PRBS_RSTVAL1			0x18
+#define MIPI_GEN_REG_SYNG_FREE_RUN			0x1c
+#define MIPI_GEN_REG_SYNG_PAUSE				0x20
+#define MIPI_GEN_REG_SYNG_NOF_FRAMES			0x24
+#define MIPI_GEN_REG_SYNG_NOF_PIXELS			0x28
+#define MIPI_GEN_REG_SYNG_NOF_LINES			0x2c
+#define MIPI_GEN_REG_SYNG_HBLANK_CYC			0x30
+#define MIPI_GEN_REG_SYNG_VBLANK_CYC			0x34
+#define MIPI_GEN_REG_SYNG_STAT_HCNT			0x38
+#define MIPI_GEN_REG_SYNG_STAT_VCNT			0x3c
+#define MIPI_GEN_REG_SYNG_STAT_FCNT			0x40
+#define MIPI_GEN_REG_SYNG_STAT_DONE			0x44
+#define MIPI_GEN_REG_TPG_MODE				0x48
+#define MIPI_GEN_REG_TPG_HCNT_MASK			0x4c
+#define MIPI_GEN_REG_TPG_VCNT_MASK			0x50
+#define MIPI_GEN_REG_TPG_XYCNT_MASK			0x54
+#define MIPI_GEN_REG_TPG_HCNT_DELTA			0x58
+#define MIPI_GEN_REG_TPG_VCNT_DELTA			0x5c
+#define MIPI_GEN_REG_TPG_R1				0x60
+#define MIPI_GEN_REG_TPG_G1				0x64
+#define MIPI_GEN_REG_TPG_B1				0x68
+#define MIPI_GEN_REG_TPG_R2				0x6c
+#define MIPI_GEN_REG_TPG_G2				0x70
+#define MIPI_GEN_REG_TPG_B2				0x74
+
+/*
+ * struct ipu_isys_tpg
+ *
+ * @nlanes: number of lanes in the receiver
+ */
+struct ipu_isys_tpg {
+	struct ipu_isys_tpg_pdata *pdata;
+	struct ipu_isys *isys;
+	struct ipu_isys_subdev asd;
+	struct ipu_isys_video av;
+
+	void __iomem *base;
+	void __iomem *sel;
+	unsigned int index;
+	int streaming;
+
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *store_csi2_header;
+};
+
+#define to_ipu_isys_tpg(sd)		\
+	container_of(to_ipu_isys_subdev(sd), \
+	struct ipu_isys_tpg, asd)
+#ifdef IPU_TPG_FRAME_SYNC
+void ipu_isys_tpg_sof_event(struct ipu_isys_tpg *tpg);
+void ipu_isys_tpg_eof_event(struct ipu_isys_tpg *tpg);
+#endif
+int ipu_isys_tpg_init(struct ipu_isys_tpg *tpg,
+		      struct ipu_isys *isys,
+		      void __iomem *base, void __iomem *sel,
+		      unsigned int index);
+void ipu_isys_tpg_cleanup(struct ipu_isys_tpg *tpg);
+int tpg_set_stream(struct v4l2_subdev *sd, int enable);
+
+#endif /* IPU_ISYS_TPG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-video.c
@@ -0,0 +1,1748 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2021 Intel Corporation
+
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/init_task.h>
+#include <linux/kthread.h>
+#include <linux/pm_runtime.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/compat.h>
+
+#include <uapi/linux/sched/types.h>
+
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mc.h>
+
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-cpd.h"
+#include "ipu-isys.h"
+#include "ipu-isys-video.h"
+#include "ipu-platform.h"
+#include "ipu-platform-regs.h"
+#include "ipu-platform-buttress-regs.h"
+#include "ipu-trace.h"
+#include "ipu-fw-isys.h"
+#include "ipu-fw-com.h"
+
+/* use max resolution pixel rate by default */
+#define DEFAULT_PIXEL_RATE	(360000000ULL * 2 * 4 / 10)
+
+const struct ipu_isys_pixelformat ipu_isys_pfmts_be_soc[] = {
+	{V4L2_PIX_FMT_Y10, 16, 10, 0, MEDIA_BUS_FMT_Y10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_UYVY, 16, 16, 0, MEDIA_BUS_FMT_UYVY8_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_UYVY},
+	{V4L2_PIX_FMT_YUYV, 16, 16, 0, MEDIA_BUS_FMT_YUYV8_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_YUYV},
+	{V4L2_PIX_FMT_NV16, 16, 16, 8, MEDIA_BUS_FMT_UYVY8_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_NV16},
+	{V4L2_PIX_FMT_XRGB32, 32, 32, 0, MEDIA_BUS_FMT_RGB565_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_RGBA888},
+	{V4L2_PIX_FMT_XBGR32, 32, 32, 0, MEDIA_BUS_FMT_RGB888_1X24,
+	 IPU_FW_ISYS_FRAME_FORMAT_RGBA888},
+	/* Raw bayer formats. */
+	{V4L2_PIX_FMT_SBGGR12, 16, 12, 0, MEDIA_BUS_FMT_SBGGR12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGBRG12, 16, 12, 0, MEDIA_BUS_FMT_SGBRG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGRBG12, 16, 12, 0, MEDIA_BUS_FMT_SGRBG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SRGGB12, 16, 12, 0, MEDIA_BUS_FMT_SRGGB12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SBGGR10, 16, 10, 0, MEDIA_BUS_FMT_SBGGR10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGBRG10, 16, 10, 0, MEDIA_BUS_FMT_SGBRG10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGRBG10, 16, 10, 0, MEDIA_BUS_FMT_SGRBG10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SRGGB10, 16, 10, 0, MEDIA_BUS_FMT_SRGGB10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SBGGR8, 8, 8, 0, MEDIA_BUS_FMT_SBGGR8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SGBRG8, 8, 8, 0, MEDIA_BUS_FMT_SGBRG8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SGRBG8, 8, 8, 0, MEDIA_BUS_FMT_SGRBG8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SRGGB8, 8, 8, 0, MEDIA_BUS_FMT_SRGGB8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{}
+};
+
+const struct ipu_isys_pixelformat ipu_isys_pfmts_packed[] = {
+	{V4L2_PIX_FMT_Y10, 10, 10, 0, MEDIA_BUS_FMT_Y10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW10},
+#ifdef V4L2_PIX_FMT_Y210
+	{V4L2_PIX_FMT_Y210, 20, 20, 0, MEDIA_BUS_FMT_YUYV10_1X20,
+	 IPU_FW_ISYS_FRAME_FORMAT_YUYV},
+#endif
+	{V4L2_PIX_FMT_UYVY, 16, 16, 0, MEDIA_BUS_FMT_UYVY8_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_UYVY},
+	{V4L2_PIX_FMT_YUYV, 16, 16, 0, MEDIA_BUS_FMT_YUYV8_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_YUYV},
+	{V4L2_PIX_FMT_RGB565, 16, 16, 0, MEDIA_BUS_FMT_RGB565_1X16,
+	 IPU_FW_ISYS_FRAME_FORMAT_RGB565},
+	{V4L2_PIX_FMT_BGR24, 24, 24, 0, MEDIA_BUS_FMT_RGB888_1X24,
+	 IPU_FW_ISYS_FRAME_FORMAT_RGBA888},
+#ifndef V4L2_PIX_FMT_SBGGR12P
+	{V4L2_PIX_FMT_SBGGR12, 12, 12, 0, MEDIA_BUS_FMT_SBGGR12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+	{V4L2_PIX_FMT_SGBRG12, 12, 12, 0, MEDIA_BUS_FMT_SGBRG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+	{V4L2_PIX_FMT_SGRBG12, 12, 12, 0, MEDIA_BUS_FMT_SGRBG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+	{V4L2_PIX_FMT_SRGGB12, 12, 12, 0, MEDIA_BUS_FMT_SRGGB12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+#else /* V4L2_PIX_FMT_SBGGR12P */
+	{V4L2_PIX_FMT_SBGGR12P, 12, 12, 0, MEDIA_BUS_FMT_SBGGR12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+	{V4L2_PIX_FMT_SGBRG12P, 12, 12, 0, MEDIA_BUS_FMT_SGBRG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+	{V4L2_PIX_FMT_SGRBG12P, 12, 12, 0, MEDIA_BUS_FMT_SGRBG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+	{V4L2_PIX_FMT_SRGGB12P, 12, 12, 0, MEDIA_BUS_FMT_SRGGB12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW12},
+#endif /* V4L2_PIX_FMT_SBGGR12P */
+	{V4L2_PIX_FMT_SBGGR10P, 10, 10, 0, MEDIA_BUS_FMT_SBGGR10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW10},
+	{V4L2_PIX_FMT_SGBRG10P, 10, 10, 0, MEDIA_BUS_FMT_SGBRG10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW10},
+	{V4L2_PIX_FMT_SGRBG10P, 10, 10, 0, MEDIA_BUS_FMT_SGRBG10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW10},
+	{V4L2_PIX_FMT_SRGGB10P, 10, 10, 0, MEDIA_BUS_FMT_SRGGB10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW10},
+	{V4L2_PIX_FMT_SBGGR8, 8, 8, 0, MEDIA_BUS_FMT_SBGGR8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SGBRG8, 8, 8, 0, MEDIA_BUS_FMT_SGBRG8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SGRBG8, 8, 8, 0, MEDIA_BUS_FMT_SGRBG8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SRGGB8, 8, 8, 0, MEDIA_BUS_FMT_SRGGB8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{}
+};
+
+static int video_open(struct file *file)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+	struct ipu_isys *isys = av->isys;
+	struct ipu_bus_device *adev = to_ipu_bus_device(&isys->adev->dev);
+	struct ipu_device *isp = adev->isp;
+	int rval;
+	const struct ipu_isys_internal_pdata *ipdata;
+
+	mutex_lock(&isys->mutex);
+
+	if (isys->reset_needed || isp->flr_done) {
+		mutex_unlock(&isys->mutex);
+		dev_warn(&isys->adev->dev, "isys power cycle required\n");
+		return -EIO;
+	}
+	mutex_unlock(&isys->mutex);
+
+	rval = pm_runtime_get_sync(&isys->adev->dev);
+	if (rval < 0) {
+		pm_runtime_put_noidle(&isys->adev->dev);
+		return rval;
+	}
+
+	rval = v4l2_fh_open(file);
+	if (rval)
+		goto out_power_down;
+
+	rval = v4l2_pipeline_pm_get(&av->vdev.entity);
+	if (rval)
+		goto out_v4l2_fh_release;
+
+	mutex_lock(&isys->mutex);
+
+	if (isys->video_opened++) {
+		/* Already open */
+		mutex_unlock(&isys->mutex);
+		return 0;
+	}
+
+	ipdata = isys->pdata->ipdata;
+	ipu_configure_spc(adev->isp,
+			  &ipdata->hw_variant,
+			  IPU_CPD_PKG_DIR_ISYS_SERVER_IDX,
+			  isys->pdata->base, isys->pkg_dir,
+			  isys->pkg_dir_dma_addr);
+
+	/*
+	 * Buffers could have been left to wrong queue at last closure.
+	 * Move them now back to empty buffer queue.
+	 */
+	ipu_cleanup_fw_msg_bufs(isys);
+
+	if (isys->fwcom) {
+		/*
+		 * Something went wrong in previous shutdown. As we are now
+		 * restarting isys we can safely delete old context.
+		 */
+		dev_err(&isys->adev->dev, "Clearing old context\n");
+		ipu_fw_isys_cleanup(isys);
+	}
+
+	rval = ipu_fw_isys_init(av->isys, ipdata->num_parallel_streams);
+	if (rval < 0)
+		goto out_lib_init;
+
+	mutex_unlock(&isys->mutex);
+
+	return 0;
+
+out_lib_init:
+	isys->video_opened--;
+	mutex_unlock(&isys->mutex);
+	v4l2_pipeline_pm_put(&av->vdev.entity);
+
+out_v4l2_fh_release:
+	v4l2_fh_release(file);
+out_power_down:
+	pm_runtime_put(&isys->adev->dev);
+
+	return rval;
+}
+
+static int video_release(struct file *file)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+	int ret = 0;
+
+	vb2_fop_release(file);
+
+	mutex_lock(&av->isys->mutex);
+
+	if (!--av->isys->video_opened) {
+		ipu_fw_isys_close(av->isys);
+		if (av->isys->fwcom) {
+			av->isys->reset_needed = true;
+			ret = -EIO;
+		}
+	}
+
+	mutex_unlock(&av->isys->mutex);
+
+	v4l2_pipeline_pm_put(&av->vdev.entity);
+
+	if (av->isys->reset_needed)
+		pm_runtime_put_sync(&av->isys->adev->dev);
+	else
+		pm_runtime_put(&av->isys->adev->dev);
+
+	return ret;
+}
+
+static struct media_pad *other_pad(struct media_pad *pad)
+{
+	struct media_link *link;
+
+	list_for_each_entry(link, &pad->entity->links, list) {
+		if ((link->flags & MEDIA_LNK_FL_LINK_TYPE)
+		    != MEDIA_LNK_FL_DATA_LINK)
+			continue;
+
+		return link->source == pad ? link->sink : link->source;
+	}
+
+	WARN_ON(1);
+	return NULL;
+}
+
+const struct ipu_isys_pixelformat *
+ipu_isys_get_pixelformat(struct ipu_isys_video *av, u32 pixelformat)
+{
+	struct media_pad *pad = other_pad(&av->vdev.entity.pads[0]);
+	struct v4l2_subdev *sd;
+	const u32 *supported_codes;
+	const struct ipu_isys_pixelformat *pfmt;
+
+	if (!pad || !pad->entity) {
+		WARN_ON(1);
+		return NULL;
+	}
+
+	sd = media_entity_to_v4l2_subdev(pad->entity);
+	supported_codes = to_ipu_isys_subdev(sd)->supported_codes[pad->index];
+
+	for (pfmt = av->pfmts; pfmt->bpp; pfmt++) {
+		unsigned int i;
+
+		if (pfmt->pixelformat != pixelformat)
+			continue;
+
+		for (i = 0; supported_codes[i]; i++) {
+			if (pfmt->code == supported_codes[i])
+				return pfmt;
+		}
+	}
+
+	/* Not found. Get the default, i.e. the first defined one. */
+	for (pfmt = av->pfmts; pfmt->bpp; pfmt++) {
+		if (pfmt->code == *supported_codes)
+			return pfmt;
+	}
+
+	WARN_ON(1);
+	return NULL;
+}
+
+int ipu_isys_vidioc_querycap(struct file *file, void *fh,
+			     struct v4l2_capability *cap)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+
+	strlcpy(cap->driver, IPU_ISYS_NAME, sizeof(cap->driver));
+	strlcpy(cap->card, av->isys->media_dev.model, sizeof(cap->card));
+	snprintf(cap->bus_info, sizeof(cap->bus_info), "PCI:%s",
+		 av->isys->media_dev.bus_info);
+	return 0;
+}
+
+int ipu_isys_vidioc_enum_fmt(struct file *file, void *fh,
+			     struct v4l2_fmtdesc *f)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+	struct media_pad *pad = other_pad(&av->vdev.entity.pads[0]);
+	struct v4l2_subdev *sd;
+	const u32 *supported_codes;
+	const struct ipu_isys_pixelformat *pfmt;
+	u32 index;
+
+	if (!pad || !pad->entity)
+		return -EINVAL;
+	sd = media_entity_to_v4l2_subdev(pad->entity);
+	supported_codes = to_ipu_isys_subdev(sd)->supported_codes[pad->index];
+
+	/* Walk the 0-terminated array for the f->index-th code. */
+	for (index = f->index; *supported_codes && index;
+	     index--, supported_codes++) {
+	};
+
+	if (!*supported_codes)
+		return -EINVAL;
+
+	f->flags = 0;
+
+	/* Code found */
+	for (pfmt = av->pfmts; pfmt->bpp; pfmt++)
+		if (pfmt->code == *supported_codes)
+			break;
+
+	if (!pfmt->bpp) {
+		dev_warn(&av->isys->adev->dev,
+			 "Format not found in mapping table.");
+		return -EINVAL;
+	}
+
+	f->pixelformat = pfmt->pixelformat;
+
+	return 0;
+}
+
+static int vidioc_g_fmt_vid_cap_mplane(struct file *file, void *fh,
+				       struct v4l2_format *fmt)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+
+	fmt->fmt.pix_mp = av->mpix;
+
+	return 0;
+}
+
+const struct ipu_isys_pixelformat *
+ipu_isys_video_try_fmt_vid_mplane_default(struct ipu_isys_video *av,
+					  struct v4l2_pix_format_mplane *mpix)
+{
+	return ipu_isys_video_try_fmt_vid_mplane(av, mpix, 0);
+}
+
+const struct ipu_isys_pixelformat *
+ipu_isys_video_try_fmt_vid_mplane(struct ipu_isys_video *av,
+				  struct v4l2_pix_format_mplane *mpix,
+				  int store_csi2_header)
+{
+	const struct ipu_isys_pixelformat *pfmt =
+	    ipu_isys_get_pixelformat(av, mpix->pixelformat);
+
+	if (!pfmt)
+		return NULL;
+	mpix->pixelformat = pfmt->pixelformat;
+	mpix->num_planes = 1;
+
+	mpix->width = clamp(mpix->width, IPU_ISYS_MIN_WIDTH,
+			    IPU_ISYS_MAX_WIDTH);
+	mpix->height = clamp(mpix->height, IPU_ISYS_MIN_HEIGHT,
+			     IPU_ISYS_MAX_HEIGHT);
+
+	if (!av->packed)
+		mpix->plane_fmt[0].bytesperline =
+		    mpix->width * DIV_ROUND_UP(pfmt->bpp_planar ?
+					       pfmt->bpp_planar : pfmt->bpp,
+					       BITS_PER_BYTE);
+	else if (store_csi2_header)
+		mpix->plane_fmt[0].bytesperline =
+		    DIV_ROUND_UP(av->line_header_length +
+				 av->line_footer_length +
+				 (unsigned int)mpix->width * pfmt->bpp,
+				 BITS_PER_BYTE);
+	else
+		mpix->plane_fmt[0].bytesperline =
+		    DIV_ROUND_UP((unsigned int)mpix->width * pfmt->bpp,
+				 BITS_PER_BYTE);
+
+	mpix->plane_fmt[0].bytesperline = ALIGN(mpix->plane_fmt[0].bytesperline,
+						av->isys->line_align);
+
+	if (pfmt->bpp_planar)
+		mpix->plane_fmt[0].bytesperline =
+		    mpix->plane_fmt[0].bytesperline *
+		    pfmt->bpp / pfmt->bpp_planar;
+	/*
+	 * (height + 1) * bytesperline due to a hardware issue: the DMA unit
+	 * is a power of two, and a line should be transferred as few units
+	 * as possible. The result is that up to line length more data than
+	 * the image size may be transferred to memory after the image.
+	 * Another limition is the GDA allocation unit size. For low
+	 * resolution it gives a bigger number. Use larger one to avoid
+	 * memory corruption.
+	 */
+	mpix->plane_fmt[0].sizeimage =
+	    max(max(mpix->plane_fmt[0].sizeimage,
+		    mpix->plane_fmt[0].bytesperline * mpix->height +
+		    max(mpix->plane_fmt[0].bytesperline,
+			av->isys->pdata->ipdata->isys_dma_overshoot)), 1U);
+
+	if (av->compression_ctrl)
+		av->compression = v4l2_ctrl_g_ctrl(av->compression_ctrl);
+
+	/* overwrite bpl/height with compression alignment */
+	if (av->compression) {
+		u32 planar_tile_status_size, tile_status_size;
+
+		mpix->plane_fmt[0].bytesperline =
+		    ALIGN(mpix->plane_fmt[0].bytesperline,
+			  IPU_ISYS_COMPRESSION_LINE_ALIGN);
+		mpix->height = ALIGN(mpix->height,
+				     IPU_ISYS_COMPRESSION_HEIGHT_ALIGN);
+
+		mpix->plane_fmt[0].sizeimage =
+		    ALIGN(mpix->plane_fmt[0].bytesperline * mpix->height,
+			  IPU_ISYS_COMPRESSION_PAGE_ALIGN);
+
+		/* ISYS compression only for RAW and single plannar */
+		planar_tile_status_size =
+		    DIV_ROUND_UP_ULL((mpix->plane_fmt[0].bytesperline *
+				      mpix->height /
+				      IPU_ISYS_COMPRESSION_TILE_SIZE_BYTES) *
+				     IPU_ISYS_COMPRESSION_TILE_STATUS_BITS,
+				     BITS_PER_BYTE);
+		tile_status_size = ALIGN(planar_tile_status_size,
+					 IPU_ISYS_COMPRESSION_PAGE_ALIGN);
+
+		/* tile status buffer offsets relative to buffer base address */
+		av->ts_offsets[0] = mpix->plane_fmt[0].sizeimage;
+		mpix->plane_fmt[0].sizeimage += tile_status_size;
+
+		dev_dbg(&av->isys->adev->dev,
+			"cmprs: bpl:%d, height:%d img size:%d, ts_sz:%d\n",
+			mpix->plane_fmt[0].bytesperline, mpix->height,
+			av->ts_offsets[0], tile_status_size);
+	}
+
+	memset(mpix->plane_fmt[0].reserved, 0,
+	       sizeof(mpix->plane_fmt[0].reserved));
+
+	if (mpix->field == V4L2_FIELD_ANY)
+		mpix->field = V4L2_FIELD_NONE;
+	/* Use defaults */
+	mpix->colorspace = V4L2_COLORSPACE_RAW;
+	mpix->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+	mpix->quantization = V4L2_QUANTIZATION_DEFAULT;
+	mpix->xfer_func = V4L2_XFER_FUNC_DEFAULT;
+
+	return pfmt;
+}
+
+static int vidioc_s_fmt_vid_cap_mplane(struct file *file, void *fh,
+				       struct v4l2_format *f)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+
+	if (av->aq.vbq.streaming)
+		return -EBUSY;
+
+	av->pfmt = av->try_fmt_vid_mplane(av, &f->fmt.pix_mp);
+	av->mpix = f->fmt.pix_mp;
+
+	return 0;
+}
+
+static int vidioc_try_fmt_vid_cap_mplane(struct file *file, void *fh,
+					 struct v4l2_format *f)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+
+	av->try_fmt_vid_mplane(av, &f->fmt.pix_mp);
+
+	return 0;
+}
+
+static long ipu_isys_vidioc_private(struct file *file, void *fh,
+				    bool valid_prio, unsigned int cmd,
+				    void *arg)
+{
+	struct ipu_isys_video *av = video_drvdata(file);
+	int ret = 0;
+
+	switch (cmd) {
+	case VIDIOC_IPU_GET_DRIVER_VERSION:
+		*(u32 *)arg = IPU_DRIVER_VERSION;
+		break;
+
+	default:
+		dev_dbg(&av->isys->adev->dev, "unsupported private ioctl %x\n",
+			cmd);
+	}
+
+	return ret;
+}
+
+static int vidioc_enum_input(struct file *file, void *fh,
+			     struct v4l2_input *input)
+{
+	if (input->index > 0)
+		return -EINVAL;
+	strlcpy(input->name, "camera", sizeof(input->name));
+	input->type = V4L2_INPUT_TYPE_CAMERA;
+
+	return 0;
+}
+
+static int vidioc_g_input(struct file *file, void *fh, unsigned int *input)
+{
+	*input = 0;
+
+	return 0;
+}
+
+static int vidioc_s_input(struct file *file, void *fh, unsigned int input)
+{
+	return input == 0 ? 0 : -EINVAL;
+}
+
+/*
+ * Return true if an entity directly connected to an Iunit entity is
+ * an image source for the ISP. This can be any external directly
+ * connected entity or any of the test pattern generators in the
+ * Iunit.
+ */
+static bool is_external(struct ipu_isys_video *av, struct media_entity *entity)
+{
+	struct v4l2_subdev *sd;
+
+	/* All video nodes are ours. */
+	if (!is_media_entity_v4l2_subdev(entity))
+		return false;
+
+	sd = media_entity_to_v4l2_subdev(entity);
+	if (strncmp(sd->name, IPU_ISYS_ENTITY_PREFIX,
+		    strlen(IPU_ISYS_ENTITY_PREFIX)) != 0)
+		return true;
+
+	return false;
+}
+
+static int link_validate(struct media_link *link)
+{
+	struct ipu_isys_video *av =
+	    container_of(link->sink, struct ipu_isys_video, pad);
+	/* All sub-devices connected to a video node are ours. */
+	struct ipu_isys_pipeline *ip =
+		to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct v4l2_subdev *sd;
+
+	if (!link->source->entity)
+		return -EINVAL;
+	sd = media_entity_to_v4l2_subdev(link->source->entity);
+	if (is_external(av, link->source->entity)) {
+		ip->external = media_entity_remote_pad(av->vdev.entity.pads);
+		ip->source = to_ipu_isys_subdev(sd)->source;
+	}
+
+	ip->nr_queues++;
+
+	return 0;
+}
+
+static void get_stream_opened(struct ipu_isys_video *av)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&av->isys->lock, flags);
+	av->isys->stream_opened++;
+	spin_unlock_irqrestore(&av->isys->lock, flags);
+}
+
+static void put_stream_opened(struct ipu_isys_video *av)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&av->isys->lock, flags);
+	av->isys->stream_opened--;
+	spin_unlock_irqrestore(&av->isys->lock, flags);
+}
+
+static int get_stream_handle(struct ipu_isys_video *av)
+{
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	unsigned int stream_handle;
+	unsigned long flags;
+
+	spin_lock_irqsave(&av->isys->lock, flags);
+	for (stream_handle = 0;
+	     stream_handle < IPU_ISYS_MAX_STREAMS; stream_handle++)
+		if (!av->isys->pipes[stream_handle])
+			break;
+	if (stream_handle == IPU_ISYS_MAX_STREAMS) {
+		spin_unlock_irqrestore(&av->isys->lock, flags);
+		return -EBUSY;
+	}
+	av->isys->pipes[stream_handle] = ip;
+	ip->stream_handle = stream_handle;
+	spin_unlock_irqrestore(&av->isys->lock, flags);
+	return 0;
+}
+
+static void put_stream_handle(struct ipu_isys_video *av)
+{
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	unsigned long flags;
+
+	spin_lock_irqsave(&av->isys->lock, flags);
+	av->isys->pipes[ip->stream_handle] = NULL;
+	ip->stream_handle = -1;
+	spin_unlock_irqrestore(&av->isys->lock, flags);
+}
+
+static int get_external_facing_format(struct ipu_isys_pipeline *ip,
+				      struct v4l2_subdev_format *format)
+{
+	struct ipu_isys_video *av = container_of(ip, struct ipu_isys_video, ip);
+	struct v4l2_subdev *sd;
+	struct media_pad *external_facing;
+
+	if (!ip->external->entity) {
+		WARN_ON(1);
+		return -ENODEV;
+	}
+	sd = media_entity_to_v4l2_subdev(ip->external->entity);
+	external_facing = (strncmp(sd->name, IPU_ISYS_ENTITY_PREFIX,
+			   strlen(IPU_ISYS_ENTITY_PREFIX)) == 0) ?
+			   ip->external :
+			   media_entity_remote_pad(ip->external);
+	if (WARN_ON(!external_facing)) {
+		dev_warn(&av->isys->adev->dev,
+			 "no external facing pad --- driver bug?\n");
+		return -EINVAL;
+	}
+
+	format->which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	format->pad = 0;
+	sd = media_entity_to_v4l2_subdev(external_facing->entity);
+
+	return v4l2_subdev_call(sd, pad, get_fmt, NULL, format);
+}
+
+static void short_packet_queue_destroy(struct ipu_isys_pipeline *ip)
+{
+	struct ipu_isys_video *av = container_of(ip, struct ipu_isys_video, ip);
+	unsigned int i;
+
+	if (!ip->short_packet_bufs)
+		return;
+	for (i = 0; i < IPU_ISYS_SHORT_PACKET_BUFFER_NUM; i++) {
+		if (ip->short_packet_bufs[i].buffer)
+			dma_free_coherent(&av->isys->adev->dev,
+					  ip->short_packet_buffer_size,
+					  ip->short_packet_bufs[i].buffer,
+					  ip->short_packet_bufs[i].dma_addr);
+	}
+	kfree(ip->short_packet_bufs);
+	ip->short_packet_bufs = NULL;
+}
+
+static int short_packet_queue_setup(struct ipu_isys_pipeline *ip)
+{
+	struct ipu_isys_video *av = container_of(ip, struct ipu_isys_video, ip);
+	struct v4l2_subdev_format source_fmt = { 0 };
+	unsigned int i;
+	int rval;
+	size_t buf_size;
+
+	INIT_LIST_HEAD(&ip->pending_interlaced_bufs);
+	ip->cur_field = V4L2_FIELD_TOP;
+
+	if (ip->isys->short_packet_source == IPU_ISYS_SHORT_PACKET_FROM_TUNIT) {
+		ip->short_packet_trace_index = 0;
+		return 0;
+	}
+
+	rval = get_external_facing_format(ip, &source_fmt);
+	if (rval)
+		return rval;
+	buf_size = IPU_ISYS_SHORT_PACKET_BUF_SIZE(source_fmt.format.height);
+	ip->short_packet_buffer_size = buf_size;
+	ip->num_short_packet_lines =
+	    IPU_ISYS_SHORT_PACKET_PKT_LINES(source_fmt.format.height);
+
+	/* Initialize short packet queue. */
+	INIT_LIST_HEAD(&ip->short_packet_incoming);
+	INIT_LIST_HEAD(&ip->short_packet_active);
+
+	ip->short_packet_bufs =
+	    kzalloc(sizeof(struct ipu_isys_private_buffer) *
+		    IPU_ISYS_SHORT_PACKET_BUFFER_NUM, GFP_KERNEL);
+	if (!ip->short_packet_bufs)
+		return -ENOMEM;
+
+	for (i = 0; i < IPU_ISYS_SHORT_PACKET_BUFFER_NUM; i++) {
+		struct ipu_isys_private_buffer *buf = &ip->short_packet_bufs[i];
+
+		buf->index = (unsigned int)i;
+		buf->ip = ip;
+		buf->ib.type = IPU_ISYS_SHORT_PACKET_BUFFER;
+		buf->bytesused = buf_size;
+		buf->buffer = dma_alloc_coherent(&av->isys->adev->dev, buf_size,
+						 &buf->dma_addr, GFP_KERNEL);
+		if (!buf->buffer) {
+			short_packet_queue_destroy(ip);
+			return -ENOMEM;
+		}
+		list_add(&buf->ib.head, &ip->short_packet_incoming);
+	}
+
+	return 0;
+}
+
+static void
+csi_short_packet_prepare_fw_cfg(struct ipu_isys_pipeline *ip,
+				struct ipu_fw_isys_stream_cfg_data_abi *cfg)
+{
+	int input_pin = cfg->nof_input_pins++;
+	int output_pin = cfg->nof_output_pins++;
+	struct ipu_fw_isys_input_pin_info_abi *input_info =
+	    &cfg->input_pins[input_pin];
+	struct ipu_fw_isys_output_pin_info_abi *output_info =
+	    &cfg->output_pins[output_pin];
+	struct ipu_isys *isys = ip->isys;
+
+	/*
+	 * Setting dt as IPU_ISYS_SHORT_PACKET_GENERAL_DT will cause
+	 * MIPI receiver to receive all MIPI short packets.
+	 */
+	input_info->dt = IPU_ISYS_SHORT_PACKET_GENERAL_DT;
+	input_info->input_res.width = IPU_ISYS_SHORT_PACKET_WIDTH;
+	input_info->input_res.height = ip->num_short_packet_lines;
+
+	ip->output_pins[output_pin].pin_ready =
+	    ipu_isys_queue_short_packet_ready;
+	ip->output_pins[output_pin].aq = NULL;
+	ip->short_packet_output_pin = output_pin;
+
+	output_info->input_pin_id = input_pin;
+	output_info->output_res.width = IPU_ISYS_SHORT_PACKET_WIDTH;
+	output_info->output_res.height = ip->num_short_packet_lines;
+	output_info->stride = IPU_ISYS_SHORT_PACKET_WIDTH *
+	    IPU_ISYS_SHORT_PACKET_UNITSIZE;
+	output_info->pt = IPU_ISYS_SHORT_PACKET_PT;
+	output_info->ft = IPU_ISYS_SHORT_PACKET_FT;
+	output_info->send_irq = 1;
+	memset(output_info->ts_offsets, 0, sizeof(output_info->ts_offsets));
+	output_info->s2m_pixel_soc_pixel_remapping =
+	    S2M_PIXEL_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING;
+	output_info->csi_be_soc_pixel_remapping =
+	    CSI_BE_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING;
+	output_info->sensor_type = isys->sensor_info.sensor_metadata;
+	output_info->snoopable = true;
+	output_info->error_handling_enable = false;
+}
+
+void
+ipu_isys_prepare_fw_cfg_default(struct ipu_isys_video *av,
+				struct ipu_fw_isys_stream_cfg_data_abi *cfg)
+{
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct ipu_isys_queue *aq = &av->aq;
+	struct ipu_fw_isys_output_pin_info_abi *pin_info;
+	struct ipu_isys *isys = av->isys;
+	unsigned int type_index, type;
+	int pin = cfg->nof_output_pins++;
+
+	aq->fw_output = pin;
+	ip->output_pins[pin].pin_ready = ipu_isys_queue_buf_ready;
+	ip->output_pins[pin].aq = aq;
+
+	pin_info = &cfg->output_pins[pin];
+	pin_info->input_pin_id = 0;
+	pin_info->output_res.width = av->mpix.width;
+	pin_info->output_res.height = av->mpix.height;
+
+	if (!av->pfmt->bpp_planar)
+		pin_info->stride = av->mpix.plane_fmt[0].bytesperline;
+	else
+		pin_info->stride = ALIGN(DIV_ROUND_UP(av->mpix.width *
+						      av->pfmt->bpp_planar,
+						      BITS_PER_BYTE),
+					 av->isys->line_align);
+
+	pin_info->pt = aq->css_pin_type;
+	pin_info->ft = av->pfmt->css_pixelformat;
+	pin_info->send_irq = 1;
+	memset(pin_info->ts_offsets, 0, sizeof(pin_info->ts_offsets));
+	pin_info->s2m_pixel_soc_pixel_remapping =
+	    S2M_PIXEL_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING;
+	pin_info->csi_be_soc_pixel_remapping =
+	    CSI_BE_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING;
+	cfg->vc = 0;
+
+	switch (pin_info->pt) {
+	/* non-snoopable sensor data to PSYS */
+	case IPU_FW_ISYS_PIN_TYPE_RAW_NS:
+		type_index = IPU_FW_ISYS_VC1_SENSOR_DATA;
+		pin_info->sensor_type = isys->sensor_types[type_index]++;
+		pin_info->snoopable = false;
+		pin_info->error_handling_enable = false;
+		type = isys->sensor_types[type_index];
+		if (type > isys->sensor_info.vc1_data_end)
+			isys->sensor_types[type_index] =
+				isys->sensor_info.vc1_data_start;
+
+		break;
+	/* snoopable META/Stats data to CPU */
+	case IPU_FW_ISYS_PIN_TYPE_METADATA_0:
+	case IPU_FW_ISYS_PIN_TYPE_METADATA_1:
+		pin_info->sensor_type = isys->sensor_info.sensor_metadata;
+		pin_info->snoopable = true;
+		pin_info->error_handling_enable = false;
+		break;
+	case IPU_FW_ISYS_PIN_TYPE_RAW_SOC:
+		if (av->compression) {
+			type_index = IPU_FW_ISYS_VC1_SENSOR_DATA;
+			pin_info->sensor_type
+				= isys->sensor_types[type_index]++;
+			pin_info->snoopable = false;
+			pin_info->error_handling_enable = false;
+			type = isys->sensor_types[type_index];
+			if (type > isys->sensor_info.vc1_data_end)
+				isys->sensor_types[type_index] =
+					isys->sensor_info.vc1_data_start;
+		} else {
+			type_index = IPU_FW_ISYS_VC0_SENSOR_DATA;
+			pin_info->sensor_type
+				= isys->sensor_types[type_index]++;
+			pin_info->snoopable = true;
+			pin_info->error_handling_enable = false;
+			type = isys->sensor_types[type_index];
+			if (type > isys->sensor_info.vc0_data_end)
+				isys->sensor_types[type_index] =
+					isys->sensor_info.vc0_data_start;
+		}
+		break;
+	case IPU_FW_ISYS_PIN_TYPE_MIPI:
+		type_index = IPU_FW_ISYS_VC0_SENSOR_DATA;
+		pin_info->sensor_type = isys->sensor_types[type_index]++;
+		pin_info->snoopable = true;
+		pin_info->error_handling_enable = false;
+		type = isys->sensor_types[type_index];
+		if (type > isys->sensor_info.vc0_data_end)
+			isys->sensor_types[type_index] =
+				isys->sensor_info.vc0_data_start;
+
+		break;
+
+	default:
+		dev_err(&av->isys->adev->dev,
+			"Unknown pin type, use metadata type as default\n");
+
+		pin_info->sensor_type = isys->sensor_info.sensor_metadata;
+		pin_info->snoopable = true;
+		pin_info->error_handling_enable = false;
+	}
+	if (av->compression) {
+		pin_info->payload_buf_size = av->mpix.plane_fmt[0].sizeimage;
+		pin_info->reserve_compression = av->compression;
+		pin_info->ts_offsets[0] = av->ts_offsets[0];
+	}
+}
+
+static unsigned int ipu_isys_get_compression_scheme(u32 code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8:
+	case MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8:
+		return 3;
+	default:
+		return 0;
+	}
+}
+
+static unsigned int get_comp_format(u32 code)
+{
+	unsigned int predictor = 0;	/* currently hard coded */
+	unsigned int udt = ipu_isys_mbus_code_to_mipi(code);
+	unsigned int scheme = ipu_isys_get_compression_scheme(code);
+
+	/* if data type is not user defined return here */
+	if (udt < IPU_ISYS_MIPI_CSI2_TYPE_USER_DEF(1) ||
+	    udt > IPU_ISYS_MIPI_CSI2_TYPE_USER_DEF(8))
+		return 0;
+
+	/*
+	 * For each user defined type (1..8) there is configuration bitfield for
+	 * decompression.
+	 *
+	 * | bit 3     | bits 2:0 |
+	 * | predictor | scheme   |
+	 * compression schemes:
+	 * 000 = no compression
+	 * 001 = 10 - 6 - 10
+	 * 010 = 10 - 7 - 10
+	 * 011 = 10 - 8 - 10
+	 * 100 = 12 - 6 - 12
+	 * 101 = 12 - 7 - 12
+	 * 110 = 12 - 8 - 12
+	 */
+
+	return ((predictor << 3) | scheme) <<
+	    ((udt - IPU_ISYS_MIPI_CSI2_TYPE_USER_DEF(1)) * 4);
+}
+
+/* Create stream and start it using the CSS FW ABI. */
+static int start_stream_firmware(struct ipu_isys_video *av,
+				 struct ipu_isys_buffer_list *bl)
+{
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct device *dev = &av->isys->adev->dev;
+	struct v4l2_subdev_selection sel_fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.target = V4L2_SEL_TGT_CROP,
+		.pad = CSI2_BE_PAD_SOURCE,
+	};
+	struct ipu_fw_isys_stream_cfg_data_abi *stream_cfg;
+	struct isys_fw_msgs *msg = NULL;
+	struct ipu_fw_isys_frame_buff_set_abi *buf = NULL;
+	struct ipu_isys_queue *aq;
+	struct ipu_isys_video *isl_av = NULL;
+	struct v4l2_subdev_format source_fmt = { 0 };
+	struct v4l2_subdev *be_sd = NULL;
+	struct media_pad *source_pad = media_entity_remote_pad(&av->pad);
+	struct ipu_fw_isys_cropping_abi *crop;
+	enum ipu_fw_isys_send_type send_type;
+	int rval, rvalout, tout;
+
+	rval = get_external_facing_format(ip, &source_fmt);
+	if (rval)
+		return rval;
+
+	msg = ipu_get_fw_msg_buf(ip);
+	if (!msg)
+		return -ENOMEM;
+
+	stream_cfg = to_stream_cfg_msg_buf(msg);
+	stream_cfg->compfmt = get_comp_format(source_fmt.format.code);
+	stream_cfg->input_pins[0].input_res.width = source_fmt.format.width;
+	stream_cfg->input_pins[0].input_res.height = source_fmt.format.height;
+	stream_cfg->input_pins[0].dt =
+	    ipu_isys_mbus_code_to_mipi(source_fmt.format.code);
+	stream_cfg->input_pins[0].mapped_dt = N_IPU_FW_ISYS_MIPI_DATA_TYPE;
+	stream_cfg->input_pins[0].mipi_decompression =
+	    IPU_FW_ISYS_MIPI_COMPRESSION_TYPE_NO_COMPRESSION;
+	stream_cfg->input_pins[0].capture_mode =
+		IPU_FW_ISYS_CAPTURE_MODE_REGULAR;
+	if (ip->csi2 && !v4l2_ctrl_g_ctrl(ip->csi2->store_csi2_header))
+		stream_cfg->input_pins[0].mipi_store_mode =
+		    IPU_FW_ISYS_MIPI_STORE_MODE_DISCARD_LONG_HEADER;
+
+	stream_cfg->src = ip->source;
+	stream_cfg->vc = 0;
+	stream_cfg->isl_use = ip->isl_mode;
+	stream_cfg->nof_input_pins = 1;
+	stream_cfg->sensor_type = IPU_FW_ISYS_SENSOR_MODE_NORMAL;
+
+	/*
+	 * Only CSI2-BE and SOC BE has the capability to do crop,
+	 * so get the crop info from csi2-be or csi2-be-soc.
+	 */
+	if (ip->csi2_be) {
+		be_sd = &ip->csi2_be->asd.sd;
+	} else if (ip->csi2_be_soc) {
+		be_sd = &ip->csi2_be_soc->asd.sd;
+		if (source_pad)
+			sel_fmt.pad = source_pad->index;
+	}
+	crop = &stream_cfg->crop;
+	if (be_sd &&
+	    !v4l2_subdev_call(be_sd, pad, get_selection, NULL, &sel_fmt)) {
+		crop->left_offset = sel_fmt.r.left;
+		crop->top_offset = sel_fmt.r.top;
+		crop->right_offset = sel_fmt.r.left + sel_fmt.r.width;
+		crop->bottom_offset = sel_fmt.r.top + sel_fmt.r.height;
+
+	} else {
+		crop->right_offset = source_fmt.format.width;
+		crop->bottom_offset = source_fmt.format.height;
+	}
+
+	/*
+	 * If the CSI-2 backend's video node is part of the pipeline
+	 * it must be arranged first in the output pin list. This is
+	 * the most probably a firmware requirement.
+	 */
+	if (ip->isl_mode == IPU_ISL_CSI2_BE)
+		isl_av = &ip->csi2_be->av;
+
+	if (isl_av) {
+		struct ipu_isys_queue *safe;
+
+		list_for_each_entry_safe(aq, safe, &ip->queues, node) {
+			struct ipu_isys_video *av = ipu_isys_queue_to_video(aq);
+
+			if (av != isl_av)
+				continue;
+
+			list_del(&aq->node);
+			list_add(&aq->node, &ip->queues);
+			break;
+		}
+	}
+
+	list_for_each_entry(aq, &ip->queues, node) {
+		struct ipu_isys_video *__av = ipu_isys_queue_to_video(aq);
+
+		__av->prepare_fw_stream(__av, stream_cfg);
+	}
+
+	if (ip->interlaced && ip->isys->short_packet_source ==
+	    IPU_ISYS_SHORT_PACKET_FROM_RECEIVER)
+		csi_short_packet_prepare_fw_cfg(ip, stream_cfg);
+
+	ipu_fw_isys_dump_stream_cfg(dev, stream_cfg);
+
+	ip->nr_output_pins = stream_cfg->nof_output_pins;
+
+	rval = get_stream_handle(av);
+	if (rval) {
+		dev_dbg(dev, "Can't get stream_handle\n");
+		return rval;
+	}
+
+	reinit_completion(&ip->stream_open_completion);
+
+	ipu_fw_isys_set_params(stream_cfg);
+
+	rval = ipu_fw_isys_complex_cmd(av->isys,
+				       ip->stream_handle,
+				       stream_cfg,
+				       to_dma_addr(msg),
+				       sizeof(*stream_cfg),
+				       IPU_FW_ISYS_SEND_TYPE_STREAM_OPEN);
+	ipu_put_fw_mgs_buf(av->isys, (uintptr_t)stream_cfg);
+
+	if (rval < 0) {
+		dev_err(dev, "can't open stream (%d)\n", rval);
+		goto out_put_stream_handle;
+	}
+
+	get_stream_opened(av);
+
+	tout = wait_for_completion_timeout(&ip->stream_open_completion,
+					   IPU_LIB_CALL_TIMEOUT_JIFFIES);
+	if (!tout) {
+		dev_err(dev, "stream open time out\n");
+		rval = -ETIMEDOUT;
+		goto out_put_stream_opened;
+	}
+	if (ip->error) {
+		dev_err(dev, "stream open error: %d\n", ip->error);
+		rval = -EIO;
+		goto out_put_stream_opened;
+	}
+	dev_dbg(dev, "start stream: open complete\n");
+
+	if (bl) {
+		msg = ipu_get_fw_msg_buf(ip);
+		if (!msg) {
+			rval = -ENOMEM;
+			goto out_put_stream_opened;
+		}
+		buf = to_frame_msg_buf(msg);
+	}
+
+	if (bl) {
+		ipu_isys_buffer_to_fw_frame_buff(buf, ip, bl);
+		ipu_isys_buffer_list_queue(bl,
+					   IPU_ISYS_BUFFER_LIST_FL_ACTIVE, 0);
+	}
+
+	reinit_completion(&ip->stream_start_completion);
+
+	if (bl) {
+		send_type = IPU_FW_ISYS_SEND_TYPE_STREAM_START_AND_CAPTURE;
+		ipu_fw_isys_dump_frame_buff_set(dev, buf,
+						stream_cfg->nof_output_pins);
+		rval = ipu_fw_isys_complex_cmd(av->isys,
+					       ip->stream_handle,
+					       buf, to_dma_addr(msg),
+					       sizeof(*buf),
+					       send_type);
+		ipu_put_fw_mgs_buf(av->isys, (uintptr_t)buf);
+	} else {
+		send_type = IPU_FW_ISYS_SEND_TYPE_STREAM_START;
+		rval = ipu_fw_isys_simple_cmd(av->isys,
+					      ip->stream_handle,
+					      send_type);
+	}
+
+	if (rval < 0) {
+		dev_err(dev, "can't start streaming (%d)\n", rval);
+		goto out_stream_close;
+	}
+
+	tout = wait_for_completion_timeout(&ip->stream_start_completion,
+					   IPU_LIB_CALL_TIMEOUT_JIFFIES);
+	if (!tout) {
+		dev_err(dev, "stream start time out\n");
+		rval = -ETIMEDOUT;
+		goto out_stream_close;
+	}
+	if (ip->error) {
+		dev_err(dev, "stream start error: %d\n", ip->error);
+		rval = -EIO;
+		goto out_stream_close;
+	}
+	dev_dbg(dev, "start stream: complete\n");
+
+	return 0;
+
+out_stream_close:
+	reinit_completion(&ip->stream_close_completion);
+
+	rvalout = ipu_fw_isys_simple_cmd(av->isys,
+					 ip->stream_handle,
+					 IPU_FW_ISYS_SEND_TYPE_STREAM_CLOSE);
+	if (rvalout < 0) {
+		dev_dbg(dev, "can't close stream (%d)\n", rvalout);
+		goto out_put_stream_opened;
+	}
+
+	tout = wait_for_completion_timeout(&ip->stream_close_completion,
+					   IPU_LIB_CALL_TIMEOUT_JIFFIES);
+	if (!tout)
+		dev_err(dev, "stream close time out\n");
+	else if (ip->error)
+		dev_err(dev, "stream close error: %d\n", ip->error);
+	else
+		dev_dbg(dev, "stream close complete\n");
+
+out_put_stream_opened:
+	put_stream_opened(av);
+
+out_put_stream_handle:
+	put_stream_handle(av);
+	return rval;
+}
+
+static void stop_streaming_firmware(struct ipu_isys_video *av)
+{
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct device *dev = &av->isys->adev->dev;
+	int rval, tout;
+	enum ipu_fw_isys_send_type send_type =
+		IPU_FW_ISYS_SEND_TYPE_STREAM_FLUSH;
+
+	reinit_completion(&ip->stream_stop_completion);
+
+	rval = ipu_fw_isys_simple_cmd(av->isys, ip->stream_handle,
+				      send_type);
+
+	if (rval < 0) {
+		dev_err(dev, "can't stop stream (%d)\n", rval);
+		return;
+	}
+
+	tout = wait_for_completion_timeout(&ip->stream_stop_completion,
+					   IPU_LIB_CALL_TIMEOUT_JIFFIES);
+	if (!tout)
+		dev_err(dev, "stream stop time out\n");
+	else if (ip->error)
+		dev_err(dev, "stream stop error: %d\n", ip->error);
+	else
+		dev_dbg(dev, "stop stream: complete\n");
+}
+
+static void close_streaming_firmware(struct ipu_isys_video *av)
+{
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct device *dev = &av->isys->adev->dev;
+	int rval, tout;
+
+	reinit_completion(&ip->stream_close_completion);
+
+	rval = ipu_fw_isys_simple_cmd(av->isys, ip->stream_handle,
+				      IPU_FW_ISYS_SEND_TYPE_STREAM_CLOSE);
+	if (rval < 0) {
+		dev_err(dev, "can't close stream (%d)\n", rval);
+		return;
+	}
+
+	tout = wait_for_completion_timeout(&ip->stream_close_completion,
+					   IPU_LIB_CALL_TIMEOUT_JIFFIES);
+	if (!tout)
+		dev_err(dev, "stream close time out\n");
+	else if (ip->error)
+		dev_err(dev, "stream close error: %d\n", ip->error);
+	else
+		dev_dbg(dev, "close stream: complete\n");
+
+	put_stream_opened(av);
+	put_stream_handle(av);
+}
+
+void
+ipu_isys_video_add_capture_done(struct ipu_isys_pipeline *ip,
+				void (*capture_done)
+				 (struct ipu_isys_pipeline *ip,
+				  struct ipu_fw_isys_resp_info_abi *resp))
+{
+	unsigned int i;
+
+	/* Different instances may register same function. Add only once */
+	for (i = 0; i < IPU_NUM_CAPTURE_DONE; i++)
+		if (ip->capture_done[i] == capture_done)
+			return;
+
+	for (i = 0; i < IPU_NUM_CAPTURE_DONE; i++) {
+		if (!ip->capture_done[i]) {
+			ip->capture_done[i] = capture_done;
+			return;
+		}
+	}
+	/*
+	 * Too many call backs registered. Change to IPU_NUM_CAPTURE_DONE
+	 * constant probably required.
+	 */
+	WARN_ON(1);
+}
+
+int ipu_isys_video_prepare_streaming(struct ipu_isys_video *av,
+				     unsigned int state)
+{
+	struct ipu_isys *isys = av->isys;
+	struct device *dev = &isys->adev->dev;
+	struct ipu_isys_pipeline *ip;
+	struct media_graph graph;
+	struct media_entity *entity;
+	struct media_device *mdev = &av->isys->media_dev;
+	int rval;
+	unsigned int i;
+
+	dev_dbg(dev, "prepare stream: %d\n", state);
+
+	if (!state) {
+		ip = to_ipu_isys_pipeline(av->vdev.entity.pipe);
+
+		if (ip->interlaced && isys->short_packet_source ==
+		    IPU_ISYS_SHORT_PACKET_FROM_RECEIVER)
+			short_packet_queue_destroy(ip);
+		media_pipeline_stop(&av->vdev.entity);
+		media_entity_enum_cleanup(&ip->entity_enum);
+		return 0;
+	}
+
+	ip = &av->ip;
+
+	WARN_ON(ip->nr_streaming);
+	ip->has_sof = false;
+	ip->nr_queues = 0;
+	ip->external = NULL;
+	atomic_set(&ip->sequence, 0);
+	ip->isl_mode = IPU_ISL_OFF;
+
+	for (i = 0; i < IPU_NUM_CAPTURE_DONE; i++)
+		ip->capture_done[i] = NULL;
+	ip->csi2_be = NULL;
+	ip->csi2_be_soc = NULL;
+	ip->csi2 = NULL;
+	ip->seq_index = 0;
+	memset(ip->seq, 0, sizeof(ip->seq));
+
+	WARN_ON(!list_empty(&ip->queues));
+	ip->interlaced = false;
+
+	rval = media_entity_enum_init(&ip->entity_enum, mdev);
+	if (rval)
+		return rval;
+
+	rval = media_pipeline_start(&av->vdev.entity, &ip->pipe);
+	if (rval < 0) {
+		dev_dbg(dev, "pipeline start failed\n");
+		goto out_enum_cleanup;
+	}
+
+	if (!ip->external) {
+		dev_err(dev, "no external entity set! Driver bug?\n");
+		rval = -EINVAL;
+		goto out_pipeline_stop;
+	}
+
+	rval = media_graph_walk_init(&graph, mdev);
+	if (rval)
+		goto out_pipeline_stop;
+
+	/* Gather all entities in the graph. */
+	mutex_lock(&mdev->graph_mutex);
+	media_graph_walk_start(&graph, &av->vdev.entity);
+	while ((entity = media_graph_walk_next(&graph)))
+		media_entity_enum_set(&ip->entity_enum, entity);
+
+	mutex_unlock(&mdev->graph_mutex);
+
+	media_graph_walk_cleanup(&graph);
+
+	if (ip->interlaced) {
+		rval = short_packet_queue_setup(ip);
+		if (rval) {
+			dev_err(&isys->adev->dev,
+				"Failed to setup short packet buffer.\n");
+			goto out_pipeline_stop;
+		}
+	}
+
+	dev_dbg(dev, "prepare stream: external entity %s\n",
+		ip->external->entity->name);
+
+	return 0;
+
+out_pipeline_stop:
+	media_pipeline_stop(&av->vdev.entity);
+
+out_enum_cleanup:
+	media_entity_enum_cleanup(&ip->entity_enum);
+
+	return rval;
+}
+
+static void configure_stream_watermark(struct ipu_isys_video *av)
+{
+	u32 vblank, hblank;
+	u64 pixel_rate;
+	int ret = 0;
+	struct v4l2_subdev *esd;
+	struct v4l2_ctrl *ctrl;
+	struct ipu_isys_pipeline *ip;
+	struct isys_iwake_watermark *iwake_watermark;
+	struct v4l2_control vb = { .id = V4L2_CID_VBLANK, .value = 0 };
+	struct v4l2_control hb = { .id = V4L2_CID_HBLANK, .value = 0 };
+
+	ip = to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	if (!ip->external->entity) {
+		WARN_ON(1);
+		return;
+	}
+	esd = media_entity_to_v4l2_subdev(ip->external->entity);
+
+	av->watermark->width = av->mpix.width;
+	av->watermark->height = av->mpix.height;
+
+	ret = v4l2_g_ctrl(esd->ctrl_handler, &vb);
+	if (!ret && vb.value >= 0)
+		vblank = vb.value;
+	else
+		vblank = 0;
+
+	ret = v4l2_g_ctrl(esd->ctrl_handler, &hb);
+	if (!ret && hb.value >= 0)
+		hblank = hb.value;
+	else
+		hblank = 0;
+
+	ctrl = v4l2_ctrl_find(esd->ctrl_handler, V4L2_CID_PIXEL_RATE);
+
+	if (!ctrl)
+		pixel_rate = DEFAULT_PIXEL_RATE;
+	else
+		pixel_rate = v4l2_ctrl_g_ctrl_int64(ctrl);
+
+	av->watermark->vblank = vblank;
+	av->watermark->hblank = hblank;
+	av->watermark->pixel_rate = pixel_rate;
+	if (!pixel_rate) {
+		iwake_watermark = av->isys->iwake_watermark;
+		mutex_lock(&iwake_watermark->mutex);
+		iwake_watermark->force_iwake_disable = true;
+		mutex_unlock(&iwake_watermark->mutex);
+		WARN(1, "%s Invalid pixel_rate, disable iwake.\n", __func__);
+		return;
+	}
+}
+
+static void calculate_stream_datarate(struct video_stream_watermark *watermark)
+{
+	u64 pixels_per_line, bytes_per_line, line_time_ns;
+	u64 pages_per_line, pb_bytes_per_line, stream_data_rate;
+	u16 sram_granulrity_shift =
+		(ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_SRAM_GRANULRITY_SHIFT : IPU6SE_SRAM_GRANULRITY_SHIFT;
+	u16 sram_granulrity_size =
+		(ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_SRAM_GRANULRITY_SIZE : IPU6SE_SRAM_GRANULRITY_SIZE;
+
+	pixels_per_line = watermark->width + watermark->hblank;
+	line_time_ns =
+		pixels_per_line * 1000 / (watermark->pixel_rate / 1000000);
+	/* 2 bytes per Bayer pixel */
+	bytes_per_line = watermark->width << 1;
+	/* bytes to IS pixel buffer pages */
+	pages_per_line = bytes_per_line >> sram_granulrity_shift;
+
+	/* pages for each line */
+	pages_per_line = DIV_ROUND_UP(bytes_per_line,
+				      sram_granulrity_size);
+	pb_bytes_per_line = pages_per_line << sram_granulrity_shift;
+
+	/* data rate MB/s */
+	stream_data_rate = (pb_bytes_per_line * 1000) / line_time_ns;
+	watermark->stream_data_rate = stream_data_rate;
+}
+
+static void update_stream_watermark(struct ipu_isys_video *av, bool state)
+{
+	struct isys_iwake_watermark *iwake_watermark;
+
+	iwake_watermark = av->isys->iwake_watermark;
+	if (state) {
+		calculate_stream_datarate(av->watermark);
+		mutex_lock(&iwake_watermark->mutex);
+		list_add(&av->watermark->stream_node,
+			 &iwake_watermark->video_list);
+		mutex_unlock(&iwake_watermark->mutex);
+	} else {
+		av->watermark->stream_data_rate = 0;
+		mutex_lock(&iwake_watermark->mutex);
+		list_del(&av->watermark->stream_node);
+		mutex_unlock(&iwake_watermark->mutex);
+	}
+	update_watermark_setting(av->isys);
+}
+
+int ipu_isys_video_set_streaming(struct ipu_isys_video *av,
+				 unsigned int state,
+				 struct ipu_isys_buffer_list *bl)
+{
+	struct device *dev = &av->isys->adev->dev;
+	struct media_device *mdev = av->vdev.entity.graph_obj.mdev;
+	struct media_entity_enum entities;
+
+	struct media_entity *entity, *entity2;
+	struct ipu_isys_pipeline *ip =
+	    to_ipu_isys_pipeline(av->vdev.entity.pipe);
+	struct v4l2_subdev *sd, *esd;
+	int rval = 0;
+
+	dev_dbg(dev, "set stream: %d\n", state);
+
+	if (!ip->external->entity) {
+		WARN_ON(1);
+		return -ENODEV;
+	}
+	esd = media_entity_to_v4l2_subdev(ip->external->entity);
+
+	if (state) {
+		rval = media_graph_walk_init(&ip->graph, mdev);
+		if (rval)
+			return rval;
+		rval = media_entity_enum_init(&entities, mdev);
+		if (rval)
+			goto out_media_entity_graph_init;
+	}
+
+	if (!state) {
+		stop_streaming_firmware(av);
+
+		/* stop external sub-device now. */
+		dev_info(dev, "stream off %s\n", ip->external->entity->name);
+
+		v4l2_subdev_call(esd, video, s_stream, state);
+	}
+
+	mutex_lock(&mdev->graph_mutex);
+
+	media_graph_walk_start(&ip->graph,
+			       &av->vdev.entity);
+
+	while ((entity = media_graph_walk_next(&ip->graph))) {
+		sd = media_entity_to_v4l2_subdev(entity);
+
+		/* Non-subdev nodes can be safely ignored here. */
+		if (!is_media_entity_v4l2_subdev(entity))
+			continue;
+
+		/* Don't start truly external devices quite yet. */
+		if (strncmp(sd->name, IPU_ISYS_ENTITY_PREFIX,
+			    strlen(IPU_ISYS_ENTITY_PREFIX)) != 0 ||
+		    ip->external->entity == entity)
+			continue;
+
+		dev_dbg(dev, "s_stream %s entity %s\n", state ? "on" : "off",
+			entity->name);
+		rval = v4l2_subdev_call(sd, video, s_stream, state);
+		if (!state)
+			continue;
+		if (rval && rval != -ENOIOCTLCMD) {
+			mutex_unlock(&mdev->graph_mutex);
+			goto out_media_entity_stop_streaming;
+		}
+
+		media_entity_enum_set(&entities, entity);
+	}
+
+	mutex_unlock(&mdev->graph_mutex);
+
+	if (av->aq.css_pin_type == IPU_FW_ISYS_PIN_TYPE_RAW_SOC) {
+		if (state)
+			configure_stream_watermark(av);
+		update_stream_watermark(av, state);
+	}
+
+	/* Oh crap */
+	if (state) {
+		rval = start_stream_firmware(av, bl);
+		if (rval)
+			goto out_media_entity_stop_streaming;
+
+		dev_dbg(dev, "set stream: source %d, stream_handle %d\n",
+			ip->source, ip->stream_handle);
+
+		/* Start external sub-device now. */
+		dev_info(dev, "stream on %s\n", ip->external->entity->name);
+
+		rval = v4l2_subdev_call(esd, video, s_stream, state);
+		if (rval)
+			goto out_media_entity_stop_streaming_firmware;
+	} else {
+		close_streaming_firmware(av);
+	}
+
+	if (state)
+		media_entity_enum_cleanup(&entities);
+	else
+		media_graph_walk_cleanup(&ip->graph);
+	av->streaming = state;
+
+	return 0;
+
+out_media_entity_stop_streaming_firmware:
+	stop_streaming_firmware(av);
+
+out_media_entity_stop_streaming:
+	mutex_lock(&mdev->graph_mutex);
+
+	media_graph_walk_start(&ip->graph,
+			       &av->vdev.entity);
+
+	while (state && (entity2 = media_graph_walk_next(&ip->graph)) &&
+	       entity2 != entity) {
+		sd = media_entity_to_v4l2_subdev(entity2);
+
+		if (!media_entity_enum_test(&entities, entity2))
+			continue;
+
+		v4l2_subdev_call(sd, video, s_stream, 0);
+	}
+
+	mutex_unlock(&mdev->graph_mutex);
+
+	media_entity_enum_cleanup(&entities);
+
+out_media_entity_graph_init:
+	media_graph_walk_cleanup(&ip->graph);
+
+	return rval;
+}
+
+#ifdef CONFIG_COMPAT
+static long ipu_isys_compat_ioctl(struct file *file, unsigned int cmd,
+				  unsigned long arg)
+{
+	long ret = -ENOIOCTLCMD;
+	void __user *up = compat_ptr(arg);
+
+	/*
+	 * at present, there is not any private IOCTL need to compat handle
+	 */
+	if (file->f_op->unlocked_ioctl)
+		ret = file->f_op->unlocked_ioctl(file, cmd, (unsigned long)up);
+
+	return ret;
+}
+#endif
+
+static const struct v4l2_ioctl_ops ioctl_ops_mplane = {
+	.vidioc_querycap = ipu_isys_vidioc_querycap,
+	.vidioc_enum_fmt_vid_cap = ipu_isys_vidioc_enum_fmt,
+	.vidioc_g_fmt_vid_cap_mplane = vidioc_g_fmt_vid_cap_mplane,
+	.vidioc_s_fmt_vid_cap_mplane = vidioc_s_fmt_vid_cap_mplane,
+	.vidioc_try_fmt_vid_cap_mplane = vidioc_try_fmt_vid_cap_mplane,
+	.vidioc_reqbufs = vb2_ioctl_reqbufs,
+	.vidioc_create_bufs = vb2_ioctl_create_bufs,
+	.vidioc_prepare_buf = vb2_ioctl_prepare_buf,
+	.vidioc_querybuf = vb2_ioctl_querybuf,
+	.vidioc_qbuf = vb2_ioctl_qbuf,
+	.vidioc_dqbuf = vb2_ioctl_dqbuf,
+	.vidioc_streamon = vb2_ioctl_streamon,
+	.vidioc_streamoff = vb2_ioctl_streamoff,
+	.vidioc_expbuf = vb2_ioctl_expbuf,
+	.vidioc_default = ipu_isys_vidioc_private,
+	.vidioc_enum_input = vidioc_enum_input,
+	.vidioc_g_input = vidioc_g_input,
+	.vidioc_s_input = vidioc_s_input,
+};
+
+static const struct media_entity_operations entity_ops = {
+	.link_validate = link_validate,
+};
+
+static const struct v4l2_file_operations isys_fops = {
+	.owner = THIS_MODULE,
+	.poll = vb2_fop_poll,
+	.unlocked_ioctl = video_ioctl2,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl32 = ipu_isys_compat_ioctl,
+#endif
+	.mmap = vb2_fop_mmap,
+	.open = video_open,
+	.release = video_release,
+};
+
+/*
+ * Do everything that's needed to initialise things related to video
+ * buffer queue, video node, and the related media entity. The caller
+ * is expected to assign isys field and set the name of the video
+ * device.
+ */
+int ipu_isys_video_init(struct ipu_isys_video *av,
+			struct media_entity *entity,
+			unsigned int pad, unsigned long pad_flags,
+			unsigned int flags)
+{
+	const struct v4l2_ioctl_ops *ioctl_ops = NULL;
+	int rval;
+
+	mutex_init(&av->mutex);
+	init_completion(&av->ip.stream_open_completion);
+	init_completion(&av->ip.stream_close_completion);
+	init_completion(&av->ip.stream_start_completion);
+	init_completion(&av->ip.stream_stop_completion);
+	INIT_LIST_HEAD(&av->ip.queues);
+	spin_lock_init(&av->ip.short_packet_queue_lock);
+	av->ip.isys = av->isys;
+
+	if (!av->watermark) {
+		av->watermark = kzalloc(sizeof(*av->watermark), GFP_KERNEL);
+		if (!av->watermark) {
+			rval = -ENOMEM;
+			goto out_mutex_destroy;
+		}
+	}
+
+	av->vdev.device_caps = V4L2_CAP_STREAMING;
+	if (pad_flags & MEDIA_PAD_FL_SINK) {
+		av->aq.vbq.type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
+		ioctl_ops = &ioctl_ops_mplane;
+		av->vdev.device_caps |= V4L2_CAP_VIDEO_CAPTURE_MPLANE;
+		av->vdev.vfl_dir = VFL_DIR_RX;
+	} else {
+		av->aq.vbq.type = V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE;
+		av->vdev.vfl_dir = VFL_DIR_TX;
+		av->vdev.device_caps |= V4L2_CAP_VIDEO_OUTPUT_MPLANE;
+	}
+	rval = ipu_isys_queue_init(&av->aq);
+	if (rval)
+		goto out_mutex_destroy;
+
+	av->pad.flags = pad_flags | MEDIA_PAD_FL_MUST_CONNECT;
+	rval = media_entity_pads_init(&av->vdev.entity, 1, &av->pad);
+	if (rval)
+		goto out_ipu_isys_queue_cleanup;
+
+	av->vdev.entity.ops = &entity_ops;
+	av->vdev.release = video_device_release_empty;
+	av->vdev.fops = &isys_fops;
+	av->vdev.v4l2_dev = &av->isys->v4l2_dev;
+	if (!av->vdev.ioctl_ops)
+		av->vdev.ioctl_ops = ioctl_ops;
+	av->vdev.queue = &av->aq.vbq;
+	av->vdev.lock = &av->mutex;
+	set_bit(V4L2_FL_USES_V4L2_FH, &av->vdev.flags);
+	video_set_drvdata(&av->vdev, av);
+
+	mutex_lock(&av->mutex);
+
+	rval = video_register_device(&av->vdev, VFL_TYPE_VIDEO, -1);
+	if (rval)
+		goto out_media_entity_cleanup;
+
+	if (pad_flags & MEDIA_PAD_FL_SINK)
+		rval = media_create_pad_link(entity, pad,
+					     &av->vdev.entity, 0, flags);
+	else
+		rval = media_create_pad_link(&av->vdev.entity, 0, entity,
+					     pad, flags);
+	if (rval) {
+		dev_info(&av->isys->adev->dev, "can't create link\n");
+		goto out_media_entity_cleanup;
+	}
+
+	av->pfmt = av->try_fmt_vid_mplane(av, &av->mpix);
+
+	mutex_unlock(&av->mutex);
+
+	return rval;
+
+out_media_entity_cleanup:
+	video_unregister_device(&av->vdev);
+	mutex_unlock(&av->mutex);
+	media_entity_cleanup(&av->vdev.entity);
+
+out_ipu_isys_queue_cleanup:
+	ipu_isys_queue_cleanup(&av->aq);
+
+out_mutex_destroy:
+	kfree(av->watermark);
+	mutex_destroy(&av->mutex);
+
+	return rval;
+}
+
+void ipu_isys_video_cleanup(struct ipu_isys_video *av)
+{
+	kfree(av->watermark);
+	video_unregister_device(&av->vdev);
+	media_entity_cleanup(&av->vdev.entity);
+	mutex_destroy(&av->mutex);
+	ipu_isys_queue_cleanup(&av->aq);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys-video.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys-video.h
@@ -0,0 +1,178 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_VIDEO_H
+#define IPU_ISYS_VIDEO_H
+
+#include <linux/mutex.h>
+#include <linux/list.h>
+#include <linux/videodev2.h>
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+
+#include "ipu-isys-queue.h"
+
+#define IPU_ISYS_OUTPUT_PINS 11
+#define IPU_NUM_CAPTURE_DONE 2
+#define IPU_ISYS_MAX_PARALLEL_SOF 2
+
+struct ipu_isys;
+struct ipu_isys_csi2_be_soc;
+struct ipu_fw_isys_stream_cfg_data_abi;
+
+struct ipu_isys_pixelformat {
+	u32 pixelformat;
+	u32 bpp;
+	u32 bpp_packed;
+	u32 bpp_planar;
+	u32 code;
+	u32 css_pixelformat;
+};
+
+struct sequence_info {
+	unsigned int sequence;
+	u64 timestamp;
+};
+
+struct output_pin_data {
+	void (*pin_ready)(struct ipu_isys_pipeline *ip,
+			  struct ipu_fw_isys_resp_info_abi *info);
+	struct ipu_isys_queue *aq;
+};
+
+struct ipu_isys_pipeline {
+	struct media_pipeline pipe;
+	struct media_pad *external;
+	atomic_t sequence;
+	unsigned int seq_index;
+	struct sequence_info seq[IPU_ISYS_MAX_PARALLEL_SOF];
+	int source;	/* SSI stream source */
+	int stream_handle;	/* stream handle for CSS API */
+	unsigned int nr_output_pins;	/* How many firmware pins? */
+	enum ipu_isl_mode isl_mode;
+	struct ipu_isys_csi2_be *csi2_be;
+	struct ipu_isys_csi2_be_soc *csi2_be_soc;
+	struct ipu_isys_csi2 *csi2;
+
+	/*
+	 * Number of capture queues, write access serialised using struct
+	 * ipu_isys.stream_mutex
+	 */
+	int nr_queues;
+	int nr_streaming;	/* Number of capture queues streaming */
+	int streaming;	/* Has streaming been really started? */
+	struct list_head queues;
+	struct completion stream_open_completion;
+	struct completion stream_close_completion;
+	struct completion stream_start_completion;
+	struct completion stream_stop_completion;
+	struct ipu_isys *isys;
+
+	void (*capture_done[IPU_NUM_CAPTURE_DONE])
+	 (struct ipu_isys_pipeline *ip,
+	  struct ipu_fw_isys_resp_info_abi *resp);
+	struct output_pin_data output_pins[IPU_ISYS_OUTPUT_PINS];
+	bool has_sof;
+	bool interlaced;
+	int error;
+	struct ipu_isys_private_buffer *short_packet_bufs;
+	size_t short_packet_buffer_size;
+	unsigned int num_short_packet_lines;
+	unsigned int short_packet_output_pin;
+	unsigned int cur_field;
+	struct list_head short_packet_incoming;
+	struct list_head short_packet_active;
+	/* Serialize access to short packet active and incoming lists */
+	spinlock_t short_packet_queue_lock;
+	struct list_head pending_interlaced_bufs;
+	unsigned int short_packet_trace_index;
+	struct media_graph graph;
+	struct media_entity_enum entity_enum;
+};
+
+#define to_ipu_isys_pipeline(__pipe)				\
+	container_of((__pipe), struct ipu_isys_pipeline, pipe)
+
+struct video_stream_watermark {
+	u32 width;
+	u32 height;
+	u32 vblank;
+	u32 hblank;
+	u32 frame_rate;
+	u64 pixel_rate;
+	u64 stream_data_rate;
+	struct list_head stream_node;
+};
+
+struct ipu_isys_video {
+	/* Serialise access to other fields in the struct. */
+	struct mutex mutex;
+	struct media_pad pad;
+	struct video_device vdev;
+	struct v4l2_pix_format_mplane mpix;
+	const struct ipu_isys_pixelformat *pfmts;
+	const struct ipu_isys_pixelformat *pfmt;
+	struct ipu_isys_queue aq;
+	struct ipu_isys *isys;
+	struct ipu_isys_pipeline ip;
+	unsigned int streaming;
+	bool packed;
+	bool compression;
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_ctrl *compression_ctrl;
+	unsigned int ts_offsets[VIDEO_MAX_PLANES];
+	unsigned int line_header_length;	/* bits */
+	unsigned int line_footer_length;	/* bits */
+
+	struct video_stream_watermark *watermark;
+
+	const struct ipu_isys_pixelformat *
+		(*try_fmt_vid_mplane)(struct ipu_isys_video *av,
+				      struct v4l2_pix_format_mplane *mpix);
+	void (*prepare_fw_stream)(struct ipu_isys_video *av,
+				  struct ipu_fw_isys_stream_cfg_data_abi *cfg);
+};
+
+#define ipu_isys_queue_to_video(__aq) \
+	container_of(__aq, struct ipu_isys_video, aq)
+
+extern const struct ipu_isys_pixelformat ipu_isys_pfmts[];
+extern const struct ipu_isys_pixelformat ipu_isys_pfmts_be_soc[];
+extern const struct ipu_isys_pixelformat ipu_isys_pfmts_packed[];
+
+const struct ipu_isys_pixelformat *
+ipu_isys_get_pixelformat(struct ipu_isys_video *av, u32 pixelformat);
+
+int ipu_isys_vidioc_querycap(struct file *file, void *fh,
+			     struct v4l2_capability *cap);
+
+int ipu_isys_vidioc_enum_fmt(struct file *file, void *fh,
+			     struct v4l2_fmtdesc *f);
+
+const struct ipu_isys_pixelformat *
+ipu_isys_video_try_fmt_vid_mplane_default(struct ipu_isys_video *av,
+					  struct v4l2_pix_format_mplane *mpix);
+
+const struct ipu_isys_pixelformat *
+ipu_isys_video_try_fmt_vid_mplane(struct ipu_isys_video *av,
+				  struct v4l2_pix_format_mplane *mpix,
+				  int store_csi2_header);
+
+void
+ipu_isys_prepare_fw_cfg_default(struct ipu_isys_video *av,
+				struct ipu_fw_isys_stream_cfg_data_abi *cfg);
+int ipu_isys_video_prepare_streaming(struct ipu_isys_video *av,
+				     unsigned int state);
+int ipu_isys_video_set_streaming(struct ipu_isys_video *av, unsigned int state,
+				 struct ipu_isys_buffer_list *bl);
+int ipu_isys_video_init(struct ipu_isys_video *av, struct media_entity *source,
+			unsigned int source_pad, unsigned long pad_flags,
+			unsigned int flags);
+void ipu_isys_video_cleanup(struct ipu_isys_video *av);
+void ipu_isys_video_add_capture_done(struct ipu_isys_pipeline *ip,
+				     void (*capture_done)
+				      (struct ipu_isys_pipeline *ip,
+				       struct ipu_fw_isys_resp_info_abi *resp));
+
+#endif /* IPU_ISYS_VIDEO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys.c
@@ -0,0 +1,1356 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2021 Intel Corporation
+
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/firmware.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/string.h>
+#include <linux/sched.h>
+#include <linux/version.h>
+
+#include <media/ipu-isys.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-async.h>
+#include "ipu.h"
+#include "ipu-bus.h"
+#include "ipu-cpd.h"
+#include "ipu-mmu.h"
+#include "ipu-dma.h"
+#include "ipu-isys.h"
+#include "ipu-isys-csi2.h"
+#include "ipu-isys-video.h"
+#include "ipu-platform-regs.h"
+#include "ipu-buttress.h"
+#include "ipu-platform.h"
+#include "ipu-platform-buttress-regs.h"
+
+#define ISYS_PM_QOS_VALUE	300
+
+#define IPU_BUTTRESS_FABIC_CONTROL	    0x68
+#define GDA_ENABLE_IWAKE_INDEX		    2
+#define GDA_IWAKE_THRESHOLD_INDEX           1
+#define GDA_IRQ_CRITICAL_THRESHOLD_INDEX    0
+
+/* LTR & DID value are 10 bit at most */
+#define LTR_DID_VAL_MAX		1023
+#define LTR_DEFAULT_VALUE	0x70503C19
+#define FILL_TIME_DEFAULT_VALUE 0xFFF0783C
+#define LTR_DID_PKGC_2R		20
+#define LTR_DID_PKGC_8		100
+#define LTR_SCALE_DEFAULT	5
+#define LTR_SCALE_1024NS	2
+#define REG_PKGC_PMON_CFG	0xB00
+
+#define VAL_PKGC_PMON_CFG_RESET 0x38
+#define VAL_PKGC_PMON_CFG_START 0x7
+
+#define IS_PIXEL_BUFFER_PAGES		0x80
+/* BIOS provides the driver the LTR and threshold information in IPU,
+ * IS pixel buffer is 256KB, MaxSRAMSize is 200KB on IPU6.
+ */
+#define IPU6_MAX_SRAM_SIZE			(200 << 10)
+/* IS pixel buffer is 128KB, MaxSRAMSize is 96KB on IPU6SE.
+ */
+#define IPU6SE_MAX_SRAM_SIZE			(96 << 10)
+/* When iwake mode is disabled the critical threshold is statically set to 75%
+ * of the IS pixel buffer criticalThreshold = (128 * 3) / 4
+ */
+#define CRITICAL_THRESHOLD_IWAKE_DISABLE	(IS_PIXEL_BUFFER_PAGES * 3 / 4)
+
+union fabric_ctrl {
+	struct {
+		u16 ltr_val   : 10;
+		u16 ltr_scale : 3;
+		u16 RSVD1     : 3;
+		u16 did_val   : 10;
+		u16 did_scale : 3;
+		u16 RSVD2     : 1;
+		u16 keep_power_in_D0   : 1;
+		u16 keep_power_override : 1;
+	} bits;
+	u32 value;
+};
+
+enum ltr_did_type {
+	LTR_IWAKE_ON,
+	LTR_IWAKE_OFF,
+	LTR_ISYS_ON,
+	LTR_ISYS_OFF,
+	LTR_TYPE_MAX
+};
+
+static int
+isys_complete_ext_device_registration(struct ipu_isys *isys,
+				      struct v4l2_subdev *sd,
+				      struct ipu_isys_csi2_config *csi2)
+{
+	unsigned int i;
+	int rval;
+
+	v4l2_set_subdev_hostdata(sd, csi2);
+
+	for (i = 0; i < sd->entity.num_pads; i++) {
+		if (sd->entity.pads[i].flags & MEDIA_PAD_FL_SOURCE)
+			break;
+	}
+
+	if (i == sd->entity.num_pads) {
+		dev_warn(&isys->adev->dev,
+			 "no source pad in external entity\n");
+		rval = -ENOENT;
+		goto skip_unregister_subdev;
+	}
+
+	rval = media_create_pad_link(&sd->entity, i,
+				     &isys->csi2[csi2->port].asd.sd.entity,
+				     0, 0);
+	if (rval) {
+		dev_warn(&isys->adev->dev, "can't create link\n");
+		goto skip_unregister_subdev;
+	}
+
+	isys->csi2[csi2->port].nlanes = csi2->nlanes;
+	return 0;
+
+skip_unregister_subdev:
+	v4l2_device_unregister_subdev(sd);
+	return rval;
+}
+
+static void isys_unregister_subdevices(struct ipu_isys *isys)
+{
+	const struct ipu_isys_internal_csi2_pdata *csi2 =
+	    &isys->pdata->ipdata->csi2;
+	unsigned int i;
+
+	for (i = 0; i < NR_OF_CSI2_BE_SOC_DEV; i++)
+		ipu_isys_csi2_be_soc_cleanup(&isys->csi2_be_soc[i]);
+
+	for (i = 0; i < csi2->nports; i++)
+		ipu_isys_csi2_cleanup(&isys->csi2[i]);
+}
+
+static int isys_register_subdevices(struct ipu_isys *isys)
+{
+	const struct ipu_isys_internal_csi2_pdata *csi2 =
+	    &isys->pdata->ipdata->csi2;
+	struct ipu_isys_csi2_be_soc *csi2_be_soc;
+	unsigned int i, k;
+	int rval;
+
+	isys->csi2 = devm_kcalloc(&isys->adev->dev, csi2->nports,
+				  sizeof(*isys->csi2), GFP_KERNEL);
+	if (!isys->csi2) {
+		rval = -ENOMEM;
+		goto fail;
+	}
+
+	for (i = 0; i < csi2->nports; i++) {
+		rval = ipu_isys_csi2_init(&isys->csi2[i], isys,
+					  isys->pdata->base +
+					  csi2->offsets[i], i);
+		if (rval)
+			goto fail;
+
+		isys->isr_csi2_bits |= IPU_ISYS_UNISPART_IRQ_CSI2(i);
+	}
+
+	for (k = 0; k < NR_OF_CSI2_BE_SOC_DEV; k++) {
+		rval = ipu_isys_csi2_be_soc_init(&isys->csi2_be_soc[k],
+						 isys, k);
+		if (rval) {
+			dev_info(&isys->adev->dev,
+				 "can't register csi2 soc be device %d\n", k);
+			goto fail;
+		}
+	}
+
+	for (i = 0; i < csi2->nports; i++) {
+		for (k = 0; k < NR_OF_CSI2_BE_SOC_DEV; k++) {
+			csi2_be_soc = &isys->csi2_be_soc[k];
+			rval =
+			    media_create_pad_link(&isys->csi2[i].asd.sd.entity,
+						  CSI2_PAD_SOURCE,
+						  &csi2_be_soc->asd.sd.entity,
+						  CSI2_BE_SOC_PAD_SINK, 0);
+			if (rval) {
+				dev_info(&isys->adev->dev,
+					 "can't create link csi2->be_soc\n");
+				goto fail;
+			}
+		}
+	}
+
+	return 0;
+
+fail:
+	isys_unregister_subdevices(isys);
+	return rval;
+}
+
+/* read ltrdid threshold values from BIOS or system configuration */
+static void get_lut_ltrdid(struct ipu_isys *isys, struct ltr_did *pltr_did)
+{
+	struct isys_iwake_watermark *iwake_watermark = isys->iwake_watermark;
+	/* default values*/
+	struct ltr_did ltrdid_default;
+
+	ltrdid_default.lut_ltr.value = LTR_DEFAULT_VALUE;
+	ltrdid_default.lut_fill_time.value = FILL_TIME_DEFAULT_VALUE;
+
+	if (iwake_watermark->ltrdid.lut_ltr.value)
+		*pltr_did = iwake_watermark->ltrdid;
+	else
+		*pltr_did = ltrdid_default;
+}
+
+static int set_iwake_register(struct ipu_isys *isys, u32 index, u32 value)
+{
+	int ret = 0;
+	u32 req_id = index;
+	u32 offset = 0;
+
+	ret = ipu_fw_isys_send_proxy_token(isys, req_id, index, offset, value);
+	if (ret)
+		dev_err(&isys->adev->dev, "write %d failed %d", index, ret);
+
+	return ret;
+}
+
+/*
+ * When input system is powered up and before enabling any new sensor capture,
+ * or after disabling any sensor capture the following values need to be set:
+ * LTR_value = LTR(usec) from calculation;
+ * LTR_scale = 2;
+ * DID_value = DID(usec) from calculation;
+ * DID_scale = 2;
+ *
+ * When input system is powered down, the LTR and DID values
+ * must be returned to the default values:
+ * LTR_value = 1023;
+ * LTR_scale = 5;
+ * DID_value = 1023;
+ * DID_scale = 2;
+ */
+static void set_iwake_ltrdid(struct ipu_isys *isys,
+			     u16 ltr,
+			     u16 did,
+			     enum ltr_did_type use)
+{
+	/* did_scale will set to 2= 1us */
+	u16 ltr_val, ltr_scale, did_val;
+	union fabric_ctrl fc;
+	struct ipu_device *isp = isys->adev->isp;
+
+	switch (use) {
+	case LTR_IWAKE_ON:
+		ltr_val = min_t(u16, ltr, (u16)LTR_DID_VAL_MAX);
+		did_val = min_t(u16, did, (u16)LTR_DID_VAL_MAX);
+		ltr_scale = (ltr == LTR_DID_VAL_MAX &&
+				did == LTR_DID_VAL_MAX) ?
+				LTR_SCALE_DEFAULT : LTR_SCALE_1024NS;
+		break;
+	case LTR_ISYS_ON:
+	case LTR_IWAKE_OFF:
+		ltr_val = LTR_DID_PKGC_2R;
+		did_val = LTR_DID_PKGC_2R;
+		ltr_scale = LTR_SCALE_1024NS;
+		break;
+	case LTR_ISYS_OFF:
+		ltr_val   = LTR_DID_VAL_MAX;
+		did_val   = LTR_DID_VAL_MAX;
+		ltr_scale = LTR_SCALE_DEFAULT;
+		break;
+	default:
+		return;
+	}
+
+	fc.value = readl(isp->base + IPU_BUTTRESS_FABIC_CONTROL);
+	fc.bits.ltr_val = ltr_val;
+	fc.bits.ltr_scale = ltr_scale;
+	fc.bits.did_val = did_val;
+	fc.bits.did_scale = 2;
+	dev_dbg(&isys->adev->dev,
+		"%s ltr: %d  did: %d", __func__, ltr_val, did_val);
+	writel(fc.value, isp->base + IPU_BUTTRESS_FABIC_CONTROL);
+}
+
+/* SW driver may clear register GDA_ENABLE_IWAKE before the FW configures the
+ * stream for debug purposes. Otherwise SW should not access this register.
+ */
+static int enable_iwake(struct ipu_isys *isys, bool enable)
+{
+	int ret = 0;
+	struct isys_iwake_watermark *iwake_watermark = isys->iwake_watermark;
+
+	mutex_lock(&iwake_watermark->mutex);
+	if (iwake_watermark->iwake_enabled == enable) {
+		mutex_unlock(&iwake_watermark->mutex);
+		return ret;
+	}
+	ret = set_iwake_register(isys, GDA_ENABLE_IWAKE_INDEX, enable);
+	if (!ret)
+		iwake_watermark->iwake_enabled = enable;
+	mutex_unlock(&iwake_watermark->mutex);
+	return ret;
+}
+
+void update_watermark_setting(struct ipu_isys *isys)
+{
+	struct isys_iwake_watermark *iwake_watermark = isys->iwake_watermark;
+	struct list_head *stream_node;
+	struct video_stream_watermark *p_watermark;
+	struct ltr_did ltrdid;
+	u16 calc_fill_time_us = 0;
+	u16 ltr = 0;
+	u16 did = 0;
+	u32 iwake_threshold, iwake_critical_threshold;
+	u64 threshold_bytes;
+	u64 isys_pb_datarate_mbs = 0;
+	u16 sram_granulrity_shift =
+		(ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_SRAM_GRANULRITY_SHIFT : IPU6SE_SRAM_GRANULRITY_SHIFT;
+	int max_sram_size =
+		(ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_MAX_SRAM_SIZE : IPU6SE_MAX_SRAM_SIZE;
+
+	mutex_lock(&iwake_watermark->mutex);
+	if (iwake_watermark->force_iwake_disable) {
+		set_iwake_ltrdid(isys, 0, 0, LTR_IWAKE_OFF);
+		set_iwake_register(isys, GDA_IRQ_CRITICAL_THRESHOLD_INDEX,
+				   CRITICAL_THRESHOLD_IWAKE_DISABLE);
+		mutex_unlock(&iwake_watermark->mutex);
+		return;
+	}
+
+	if (list_empty(&iwake_watermark->video_list)) {
+		isys_pb_datarate_mbs = 0;
+	} else {
+		list_for_each(stream_node, &iwake_watermark->video_list)
+		{
+			p_watermark = list_entry(stream_node,
+						 struct video_stream_watermark,
+						 stream_node);
+			isys_pb_datarate_mbs += p_watermark->stream_data_rate;
+		}
+	}
+	mutex_unlock(&iwake_watermark->mutex);
+
+	if (!isys_pb_datarate_mbs) {
+		enable_iwake(isys, false);
+		set_iwake_ltrdid(isys, 0, 0, LTR_IWAKE_OFF);
+		mutex_lock(&iwake_watermark->mutex);
+		set_iwake_register(isys, GDA_IRQ_CRITICAL_THRESHOLD_INDEX,
+				   CRITICAL_THRESHOLD_IWAKE_DISABLE);
+		mutex_unlock(&iwake_watermark->mutex);
+	} else {
+		/* should enable iwake by default according to FW */
+		enable_iwake(isys, true);
+		calc_fill_time_us = (u16)(max_sram_size / isys_pb_datarate_mbs);
+		get_lut_ltrdid(isys, &ltrdid);
+
+		if (calc_fill_time_us <= ltrdid.lut_fill_time.bits.th0)
+			ltr = 0;
+		else if (calc_fill_time_us <= ltrdid.lut_fill_time.bits.th1)
+			ltr = ltrdid.lut_ltr.bits.val0;
+		else if (calc_fill_time_us <= ltrdid.lut_fill_time.bits.th2)
+			ltr = ltrdid.lut_ltr.bits.val1;
+		else if (calc_fill_time_us <= ltrdid.lut_fill_time.bits.th3)
+			ltr = ltrdid.lut_ltr.bits.val2;
+		else
+			ltr = ltrdid.lut_ltr.bits.val3;
+
+		did = calc_fill_time_us - ltr;
+
+		threshold_bytes = did * isys_pb_datarate_mbs;
+		/* calculate iwake threshold with 2KB granularity pages */
+		iwake_threshold =
+			max_t(u32, 1, threshold_bytes >> sram_granulrity_shift);
+
+		iwake_threshold = min_t(u32, iwake_threshold, max_sram_size);
+
+		/* set the critical threshold to halfway between
+		 * iwake threshold and the full buffer.
+		 */
+		iwake_critical_threshold = iwake_threshold +
+			(IS_PIXEL_BUFFER_PAGES - iwake_threshold) / 2;
+
+		dev_dbg(&isys->adev->dev, "%s threshold: %u  critical: %u",
+			__func__, iwake_threshold, iwake_critical_threshold);
+		set_iwake_ltrdid(isys, ltr, did, LTR_IWAKE_ON);
+		mutex_lock(&iwake_watermark->mutex);
+		set_iwake_register(isys,
+				   GDA_IWAKE_THRESHOLD_INDEX, iwake_threshold);
+
+		set_iwake_register(isys,
+				   GDA_IRQ_CRITICAL_THRESHOLD_INDEX,
+				   iwake_critical_threshold);
+		mutex_unlock(&iwake_watermark->mutex);
+
+		writel(VAL_PKGC_PMON_CFG_RESET,
+		       isys->adev->isp->base + REG_PKGC_PMON_CFG);
+		writel(VAL_PKGC_PMON_CFG_START,
+		       isys->adev->isp->base + REG_PKGC_PMON_CFG);
+	}
+}
+
+static int isys_iwake_watermark_init(struct ipu_isys *isys)
+{
+	struct isys_iwake_watermark *iwake_watermark;
+
+	if (isys->iwake_watermark)
+		return 0;
+
+	iwake_watermark = devm_kzalloc(&isys->adev->dev,
+				       sizeof(*iwake_watermark), GFP_KERNEL);
+	if (!iwake_watermark)
+		return -ENOMEM;
+	INIT_LIST_HEAD(&iwake_watermark->video_list);
+	mutex_init(&iwake_watermark->mutex);
+
+	iwake_watermark->ltrdid.lut_ltr.value = 0;
+	isys->iwake_watermark = iwake_watermark;
+	iwake_watermark->isys = isys;
+	iwake_watermark->iwake_enabled = false;
+	iwake_watermark->force_iwake_disable = false;
+	return 0;
+}
+
+static int isys_iwake_watermark_cleanup(struct ipu_isys *isys)
+{
+	struct isys_iwake_watermark *iwake_watermark = isys->iwake_watermark;
+
+	if (!iwake_watermark)
+		return -EINVAL;
+	mutex_lock(&iwake_watermark->mutex);
+	list_del(&iwake_watermark->video_list);
+	mutex_unlock(&iwake_watermark->mutex);
+	mutex_destroy(&iwake_watermark->mutex);
+	isys->iwake_watermark = NULL;
+	return 0;
+}
+
+/* The .bound() notifier callback when a match is found */
+static int isys_notifier_bound(struct v4l2_async_notifier *notifier,
+			       struct v4l2_subdev *sd,
+			       struct v4l2_async_subdev *asd)
+{
+	struct ipu_isys *isys = container_of(notifier,
+					struct ipu_isys, notifier);
+	struct sensor_async_subdev *s_asd = container_of(asd,
+					struct sensor_async_subdev, asd);
+
+	dev_info(&isys->adev->dev, "bind %s nlanes is %d port is %d\n",
+		 sd->name, s_asd->csi2.nlanes, s_asd->csi2.port);
+	isys_complete_ext_device_registration(isys, sd, &s_asd->csi2);
+
+	return v4l2_device_register_subdev_nodes(&isys->v4l2_dev);
+}
+
+static void isys_notifier_unbind(struct v4l2_async_notifier *notifier,
+				 struct v4l2_subdev *sd,
+				 struct v4l2_async_subdev *asd)
+{
+	struct ipu_isys *isys = container_of(notifier,
+					struct ipu_isys, notifier);
+
+	dev_info(&isys->adev->dev, "unbind %s\n", sd->name);
+}
+
+static int isys_notifier_complete(struct v4l2_async_notifier *notifier)
+{
+	struct ipu_isys *isys = container_of(notifier,
+					struct ipu_isys, notifier);
+
+	dev_info(&isys->adev->dev, "All sensor registration completed.\n");
+
+	return v4l2_device_register_subdev_nodes(&isys->v4l2_dev);
+}
+
+static const struct v4l2_async_notifier_operations isys_async_ops = {
+	.bound = isys_notifier_bound,
+	.unbind = isys_notifier_unbind,
+	.complete = isys_notifier_complete,
+};
+
+static int isys_fwnode_parse(struct device *dev,
+			     struct v4l2_fwnode_endpoint *vep,
+			     struct v4l2_async_subdev *asd)
+{
+	struct sensor_async_subdev *s_asd =
+			container_of(asd, struct sensor_async_subdev, asd);
+
+	s_asd->csi2.port = vep->base.port;
+	s_asd->csi2.nlanes = vep->bus.mipi_csi2.num_data_lanes;
+
+	return 0;
+}
+
+static int isys_notifier_init(struct ipu_isys *isys)
+{
+	struct ipu_device *isp = isys->adev->isp;
+	size_t asd_struct_size = sizeof(struct sensor_async_subdev);
+	int ret;
+
+	v4l2_async_notifier_init(&isys->notifier);
+	ret = v4l2_async_notifier_parse_fwnode_endpoints(&isp->pdev->dev,
+							 &isys->notifier,
+							 asd_struct_size,
+							 isys_fwnode_parse);
+
+	if (ret < 0) {
+		dev_err(&isys->adev->dev,
+			"v4l2 parse_fwnode_endpoints() failed: %d\n", ret);
+		return ret;
+	}
+
+	if (list_empty(&isys->notifier.asd_list)) {
+		/* isys probe could continue with async subdevs missing */
+		dev_warn(&isys->adev->dev, "no subdev found in graph\n");
+		return 0;
+	}
+
+	isys->notifier.ops = &isys_async_ops;
+	ret = v4l2_async_notifier_register(&isys->v4l2_dev, &isys->notifier);
+	if (ret) {
+		dev_err(&isys->adev->dev,
+			"failed to register async notifier : %d\n", ret);
+		v4l2_async_notifier_cleanup(&isys->notifier);
+	}
+
+	return ret;
+}
+
+static void isys_notifier_cleanup(struct ipu_isys *isys)
+{
+	v4l2_async_notifier_unregister(&isys->notifier);
+	v4l2_async_notifier_cleanup(&isys->notifier);
+}
+
+static struct media_device_ops isys_mdev_ops = {
+	.link_notify = v4l2_pipeline_link_notify,
+};
+
+static int isys_register_devices(struct ipu_isys *isys)
+{
+	int rval;
+
+	isys->media_dev.dev = &isys->adev->dev;
+	isys->media_dev.ops = &isys_mdev_ops;
+	strlcpy(isys->media_dev.model,
+		IPU_MEDIA_DEV_MODEL_NAME, sizeof(isys->media_dev.model));
+	snprintf(isys->media_dev.bus_info, sizeof(isys->media_dev.bus_info),
+		 "pci:%s", dev_name(isys->adev->dev.parent->parent));
+	strlcpy(isys->v4l2_dev.name, isys->media_dev.model,
+		sizeof(isys->v4l2_dev.name));
+
+	media_device_init(&isys->media_dev);
+
+	rval = media_device_register(&isys->media_dev);
+	if (rval < 0) {
+		dev_info(&isys->adev->dev, "can't register media device\n");
+		goto out_media_device_unregister;
+	}
+
+	isys->v4l2_dev.mdev = &isys->media_dev;
+
+	rval = v4l2_device_register(&isys->adev->dev, &isys->v4l2_dev);
+	if (rval < 0) {
+		dev_info(&isys->adev->dev, "can't register v4l2 device\n");
+		goto out_media_device_unregister;
+	}
+
+	rval = isys_register_subdevices(isys);
+	if (rval)
+		goto out_v4l2_device_unregister;
+
+	rval = isys_notifier_init(isys);
+	if (rval)
+		goto out_isys_unregister_subdevices;
+
+	rval = v4l2_device_register_subdev_nodes(&isys->v4l2_dev);
+	if (rval)
+		goto out_isys_notifier_cleanup;
+
+	return 0;
+
+out_isys_notifier_cleanup:
+	isys_notifier_cleanup(isys);
+
+out_isys_unregister_subdevices:
+	isys_unregister_subdevices(isys);
+
+out_v4l2_device_unregister:
+	v4l2_device_unregister(&isys->v4l2_dev);
+
+out_media_device_unregister:
+	media_device_unregister(&isys->media_dev);
+	media_device_cleanup(&isys->media_dev);
+
+	return rval;
+}
+
+static void isys_unregister_devices(struct ipu_isys *isys)
+{
+	isys_unregister_subdevices(isys);
+	v4l2_device_unregister(&isys->v4l2_dev);
+	media_device_unregister(&isys->media_dev);
+	media_device_cleanup(&isys->media_dev);
+}
+
+#ifdef CONFIG_PM
+static int isys_runtime_pm_resume(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_device *isp = adev->isp;
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	unsigned long flags;
+	int ret;
+
+	if (!isys)
+		return 0;
+
+	ret = ipu_mmu_hw_init(adev->mmu);
+	if (ret)
+		return ret;
+
+	ipu_trace_restore(dev);
+
+	cpu_latency_qos_update_request(&isys->pm_qos, ISYS_PM_QOS_VALUE);
+
+	ret = ipu_buttress_start_tsc_sync(isp);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&isys->power_lock, flags);
+	isys->power = 1;
+	spin_unlock_irqrestore(&isys->power_lock, flags);
+
+	if (isys->short_packet_source == IPU_ISYS_SHORT_PACKET_FROM_TUNIT) {
+		mutex_lock(&isys->short_packet_tracing_mutex);
+		isys->short_packet_tracing_count = 0;
+		mutex_unlock(&isys->short_packet_tracing_mutex);
+	}
+	isys_setup_hw(isys);
+
+	set_iwake_ltrdid(isys, 0, 0, LTR_ISYS_ON);
+	return 0;
+}
+
+static int isys_runtime_pm_suspend(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	unsigned long flags;
+
+	if (!isys)
+		return 0;
+
+	spin_lock_irqsave(&isys->power_lock, flags);
+	isys->power = 0;
+	spin_unlock_irqrestore(&isys->power_lock, flags);
+
+	ipu_trace_stop(dev);
+	mutex_lock(&isys->mutex);
+	isys->reset_needed = false;
+	mutex_unlock(&isys->mutex);
+
+	cpu_latency_qos_update_request(&isys->pm_qos, PM_QOS_DEFAULT_VALUE);
+
+	ipu_mmu_hw_cleanup(adev->mmu);
+
+	set_iwake_ltrdid(isys, 0, 0, LTR_ISYS_OFF);
+	return 0;
+}
+
+static int isys_suspend(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+
+	/* If stream is open, refuse to suspend */
+	if (isys->stream_opened)
+		return -EBUSY;
+
+	return 0;
+}
+
+static int isys_resume(struct device *dev)
+{
+	return 0;
+}
+
+static const struct dev_pm_ops isys_pm_ops = {
+	.runtime_suspend = isys_runtime_pm_suspend,
+	.runtime_resume = isys_runtime_pm_resume,
+	.suspend = isys_suspend,
+	.resume = isys_resume,
+};
+
+#define ISYS_PM_OPS (&isys_pm_ops)
+#else
+#define ISYS_PM_OPS NULL
+#endif
+
+static void isys_remove(struct ipu_bus_device *adev)
+{
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	struct ipu_device *isp = adev->isp;
+	struct isys_fw_msgs *fwmsg, *safe;
+
+	dev_info(&adev->dev, "removed\n");
+#ifdef CONFIG_DEBUG_FS
+	if (isp->ipu_dir)
+		debugfs_remove_recursive(isys->debugfsdir);
+#endif
+
+	list_for_each_entry_safe(fwmsg, safe, &isys->framebuflist, head) {
+		dma_free_attrs(&adev->dev, sizeof(struct isys_fw_msgs),
+			       fwmsg, fwmsg->dma_addr,
+			       0);
+	}
+
+	list_for_each_entry_safe(fwmsg, safe, &isys->framebuflist_fw, head) {
+		dma_free_attrs(&adev->dev, sizeof(struct isys_fw_msgs),
+			       fwmsg, fwmsg->dma_addr,
+			       0
+		    );
+	}
+
+	isys_iwake_watermark_cleanup(isys);
+
+	ipu_trace_uninit(&adev->dev);
+	isys_notifier_cleanup(isys);
+	isys_unregister_devices(isys);
+
+	cpu_latency_qos_remove_request(&isys->pm_qos);
+
+	if (!isp->secure_mode) {
+		ipu_cpd_free_pkg_dir(adev, isys->pkg_dir,
+				     isys->pkg_dir_dma_addr,
+				     isys->pkg_dir_size);
+		ipu_buttress_unmap_fw_image(adev, &isys->fw_sgt);
+		release_firmware(isys->fw);
+	}
+
+	mutex_destroy(&isys->stream_mutex);
+	mutex_destroy(&isys->mutex);
+
+	if (isys->short_packet_source == IPU_ISYS_SHORT_PACKET_FROM_TUNIT) {
+		u32 trace_size = IPU_ISYS_SHORT_PACKET_TRACE_BUFFER_SIZE;
+
+		dma_free_coherent(&adev->dev, trace_size,
+				  isys->short_packet_trace_buffer,
+				  isys->short_packet_trace_buffer_dma_addr);
+	}
+}
+
+#ifdef CONFIG_DEBUG_FS
+static int ipu_isys_icache_prefetch_get(void *data, u64 *val)
+{
+	struct ipu_isys *isys = data;
+
+	*val = isys->icache_prefetch;
+	return 0;
+}
+
+static int ipu_isys_icache_prefetch_set(void *data, u64 val)
+{
+	struct ipu_isys *isys = data;
+
+	if (val != !!val)
+		return -EINVAL;
+
+	isys->icache_prefetch = val;
+
+	return 0;
+}
+
+static int isys_iwake_control_get(void *data, u64 *val)
+{
+	struct ipu_isys *isys = data;
+	struct isys_iwake_watermark *iwake_watermark = isys->iwake_watermark;
+
+	mutex_lock(&iwake_watermark->mutex);
+	*val = isys->iwake_watermark->force_iwake_disable;
+	mutex_unlock(&iwake_watermark->mutex);
+	return 0;
+}
+
+static int isys_iwake_control_set(void *data, u64 val)
+{
+	struct ipu_isys *isys = data;
+	struct isys_iwake_watermark *iwake_watermark;
+
+	if (val != !!val)
+		return -EINVAL;
+	/* If stream is open, refuse to set iwake */
+	if (isys->stream_opened)
+		return -EBUSY;
+
+	iwake_watermark = isys->iwake_watermark;
+	mutex_lock(&iwake_watermark->mutex);
+	isys->iwake_watermark->force_iwake_disable = !!val;
+	mutex_unlock(&iwake_watermark->mutex);
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(isys_icache_prefetch_fops,
+			ipu_isys_icache_prefetch_get,
+			ipu_isys_icache_prefetch_set, "%llu\n");
+
+DEFINE_SIMPLE_ATTRIBUTE(isys_iwake_control_fops,
+			isys_iwake_control_get,
+			isys_iwake_control_set, "%llu\n");
+
+static int ipu_isys_init_debugfs(struct ipu_isys *isys)
+{
+	struct dentry *file;
+	struct dentry *dir;
+#ifdef IPU_ISYS_GPC
+	int ret;
+#endif
+
+	dir = debugfs_create_dir("isys", isys->adev->isp->ipu_dir);
+	if (IS_ERR(dir))
+		return -ENOMEM;
+
+	file = debugfs_create_file("icache_prefetch", 0600,
+				   dir, isys, &isys_icache_prefetch_fops);
+	if (IS_ERR(file))
+		goto err;
+
+	file = debugfs_create_file("iwake_disable", 0600,
+				   dir, isys, &isys_iwake_control_fops);
+	if (IS_ERR(file))
+		goto err;
+
+	isys->debugfsdir = dir;
+
+#ifdef IPU_ISYS_GPC
+	ret = ipu_isys_gpc_init_debugfs(isys);
+	if (ret)
+		return ret;
+#endif
+
+	return 0;
+err:
+	debugfs_remove_recursive(dir);
+	return -ENOMEM;
+}
+#endif
+
+static int alloc_fw_msg_bufs(struct ipu_isys *isys, int amount)
+{
+	dma_addr_t dma_addr;
+	struct isys_fw_msgs *addr;
+	unsigned int i;
+	unsigned long flags;
+
+	for (i = 0; i < amount; i++) {
+		addr = dma_alloc_attrs(&isys->adev->dev,
+				       sizeof(struct isys_fw_msgs),
+				       &dma_addr, GFP_KERNEL,
+				       0);
+		if (!addr)
+			break;
+		addr->dma_addr = dma_addr;
+
+		spin_lock_irqsave(&isys->listlock, flags);
+		list_add(&addr->head, &isys->framebuflist);
+		spin_unlock_irqrestore(&isys->listlock, flags);
+	}
+	if (i == amount)
+		return 0;
+	spin_lock_irqsave(&isys->listlock, flags);
+	while (!list_empty(&isys->framebuflist)) {
+		addr = list_first_entry(&isys->framebuflist,
+					struct isys_fw_msgs, head);
+		list_del(&addr->head);
+		spin_unlock_irqrestore(&isys->listlock, flags);
+		dma_free_attrs(&isys->adev->dev,
+			       sizeof(struct isys_fw_msgs),
+			       addr, addr->dma_addr,
+			       0);
+		spin_lock_irqsave(&isys->listlock, flags);
+	}
+	spin_unlock_irqrestore(&isys->listlock, flags);
+	return -ENOMEM;
+}
+
+struct isys_fw_msgs *ipu_get_fw_msg_buf(struct ipu_isys_pipeline *ip)
+{
+	struct ipu_isys_video *pipe_av =
+	    container_of(ip, struct ipu_isys_video, ip);
+	struct ipu_isys *isys;
+	struct isys_fw_msgs *msg;
+	unsigned long flags;
+
+	isys = pipe_av->isys;
+
+	spin_lock_irqsave(&isys->listlock, flags);
+	if (list_empty(&isys->framebuflist)) {
+		spin_unlock_irqrestore(&isys->listlock, flags);
+		dev_dbg(&isys->adev->dev, "Frame list empty - Allocate more");
+
+		alloc_fw_msg_bufs(isys, 5);
+
+		spin_lock_irqsave(&isys->listlock, flags);
+		if (list_empty(&isys->framebuflist)) {
+			spin_unlock_irqrestore(&isys->listlock, flags);
+			dev_err(&isys->adev->dev, "Frame list empty");
+			return NULL;
+		}
+	}
+	msg = list_last_entry(&isys->framebuflist, struct isys_fw_msgs, head);
+	list_move(&msg->head, &isys->framebuflist_fw);
+	spin_unlock_irqrestore(&isys->listlock, flags);
+	memset(&msg->fw_msg, 0, sizeof(msg->fw_msg));
+
+	return msg;
+}
+
+void ipu_cleanup_fw_msg_bufs(struct ipu_isys *isys)
+{
+	struct isys_fw_msgs *fwmsg, *fwmsg0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&isys->listlock, flags);
+	list_for_each_entry_safe(fwmsg, fwmsg0, &isys->framebuflist_fw, head)
+		list_move(&fwmsg->head, &isys->framebuflist);
+	spin_unlock_irqrestore(&isys->listlock, flags);
+}
+
+void ipu_put_fw_mgs_buf(struct ipu_isys *isys, u64 data)
+{
+	struct isys_fw_msgs *msg;
+	unsigned long flags;
+	u64 *ptr = (u64 *)(unsigned long)data;
+
+	if (!ptr)
+		return;
+
+	spin_lock_irqsave(&isys->listlock, flags);
+	msg = container_of(ptr, struct isys_fw_msgs, fw_msg.dummy);
+	list_move(&msg->head, &isys->framebuflist);
+	spin_unlock_irqrestore(&isys->listlock, flags);
+}
+
+static int isys_probe(struct ipu_bus_device *adev)
+{
+	struct ipu_isys *isys;
+	struct ipu_device *isp = adev->isp;
+	const struct firmware *fw;
+	int rval = 0;
+
+	isys = devm_kzalloc(&adev->dev, sizeof(*isys), GFP_KERNEL);
+	if (!isys)
+		return -ENOMEM;
+
+	rval = ipu_mmu_hw_init(adev->mmu);
+	if (rval)
+		return rval;
+
+	/* By default, short packet is captured from T-Unit. */
+	isys->short_packet_source = IPU_ISYS_SHORT_PACKET_FROM_RECEIVER;
+	isys->adev = adev;
+	isys->pdata = adev->pdata;
+
+	/* initial streamID for different sensor types */
+	if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) {
+		isys->sensor_info.vc1_data_start =
+			IPU6_FW_ISYS_VC1_SENSOR_DATA_START;
+		isys->sensor_info.vc1_data_end =
+			IPU6_FW_ISYS_VC1_SENSOR_DATA_END;
+		isys->sensor_info.vc0_data_start =
+			IPU6_FW_ISYS_VC0_SENSOR_DATA_START;
+		isys->sensor_info.vc0_data_end =
+			IPU6_FW_ISYS_VC0_SENSOR_DATA_END;
+		isys->sensor_info.vc1_pdaf_start =
+			IPU6_FW_ISYS_VC1_SENSOR_PDAF_START;
+		isys->sensor_info.vc1_pdaf_end =
+			IPU6_FW_ISYS_VC1_SENSOR_PDAF_END;
+		isys->sensor_info.sensor_metadata =
+			IPU6_FW_ISYS_SENSOR_METADATA;
+
+		isys->sensor_types[IPU_FW_ISYS_VC1_SENSOR_DATA] =
+			IPU6_FW_ISYS_VC1_SENSOR_DATA_START;
+		isys->sensor_types[IPU_FW_ISYS_VC1_SENSOR_PDAF] =
+			IPU6_FW_ISYS_VC1_SENSOR_PDAF_START;
+		isys->sensor_types[IPU_FW_ISYS_VC0_SENSOR_DATA] =
+			IPU6_FW_ISYS_VC0_SENSOR_DATA_START;
+	} else if (ipu_ver == IPU_VER_6SE) {
+		isys->sensor_info.vc1_data_start =
+			IPU6SE_FW_ISYS_VC1_SENSOR_DATA_START;
+		isys->sensor_info.vc1_data_end =
+			IPU6SE_FW_ISYS_VC1_SENSOR_DATA_END;
+		isys->sensor_info.vc0_data_start =
+			IPU6SE_FW_ISYS_VC0_SENSOR_DATA_START;
+		isys->sensor_info.vc0_data_end =
+			IPU6SE_FW_ISYS_VC0_SENSOR_DATA_END;
+		isys->sensor_info.vc1_pdaf_start =
+			IPU6SE_FW_ISYS_VC1_SENSOR_PDAF_START;
+		isys->sensor_info.vc1_pdaf_end =
+			IPU6SE_FW_ISYS_VC1_SENSOR_PDAF_END;
+		isys->sensor_info.sensor_metadata =
+			IPU6SE_FW_ISYS_SENSOR_METADATA;
+
+		isys->sensor_types[IPU_FW_ISYS_VC1_SENSOR_DATA] =
+			IPU6SE_FW_ISYS_VC1_SENSOR_DATA_START;
+		isys->sensor_types[IPU_FW_ISYS_VC1_SENSOR_PDAF] =
+			IPU6SE_FW_ISYS_VC1_SENSOR_PDAF_START;
+		isys->sensor_types[IPU_FW_ISYS_VC0_SENSOR_DATA] =
+			IPU6SE_FW_ISYS_VC0_SENSOR_DATA_START;
+	}
+
+	INIT_LIST_HEAD(&isys->requests);
+
+	spin_lock_init(&isys->lock);
+	spin_lock_init(&isys->power_lock);
+	isys->power = 0;
+
+	mutex_init(&isys->mutex);
+	mutex_init(&isys->stream_mutex);
+	mutex_init(&isys->lib_mutex);
+
+	spin_lock_init(&isys->listlock);
+	INIT_LIST_HEAD(&isys->framebuflist);
+	INIT_LIST_HEAD(&isys->framebuflist_fw);
+
+	dev_dbg(&adev->dev, "isys probe %p %p\n", adev, &adev->dev);
+	ipu_bus_set_drvdata(adev, isys);
+
+	isys->line_align = IPU_ISYS_2600_MEM_LINE_ALIGN;
+	isys->icache_prefetch = 0;
+
+#ifndef CONFIG_PM
+	isys_setup_hw(isys);
+#endif
+
+	if (!isp->secure_mode) {
+		fw = isp->cpd_fw;
+		rval = ipu_buttress_map_fw_image(adev, fw, &isys->fw_sgt);
+		if (rval)
+			goto release_firmware;
+
+		isys->pkg_dir =
+		    ipu_cpd_create_pkg_dir(adev, isp->cpd_fw->data,
+					   sg_dma_address(isys->fw_sgt.sgl),
+					   &isys->pkg_dir_dma_addr,
+					   &isys->pkg_dir_size);
+		if (!isys->pkg_dir) {
+			rval = -ENOMEM;
+			goto remove_shared_buffer;
+		}
+	}
+
+#ifdef CONFIG_DEBUG_FS
+	/* Debug fs failure is not fatal. */
+	ipu_isys_init_debugfs(isys);
+#endif
+
+	ipu_trace_init(adev->isp, isys->pdata->base, &adev->dev,
+		       isys_trace_blocks);
+
+	cpu_latency_qos_add_request(&isys->pm_qos, PM_QOS_DEFAULT_VALUE);
+	alloc_fw_msg_bufs(isys, 20);
+
+	rval = isys_register_devices(isys);
+	if (rval)
+		goto out_remove_pkg_dir_shared_buffer;
+	rval = isys_iwake_watermark_init(isys);
+	if (rval)
+		goto out_unregister_devices;
+
+	ipu_mmu_hw_cleanup(adev->mmu);
+
+	return 0;
+
+out_unregister_devices:
+	isys_iwake_watermark_cleanup(isys);
+	isys_unregister_devices(isys);
+out_remove_pkg_dir_shared_buffer:
+	if (!isp->secure_mode)
+		ipu_cpd_free_pkg_dir(adev, isys->pkg_dir,
+				     isys->pkg_dir_dma_addr,
+				     isys->pkg_dir_size);
+remove_shared_buffer:
+	if (!isp->secure_mode)
+		ipu_buttress_unmap_fw_image(adev, &isys->fw_sgt);
+release_firmware:
+	if (!isp->secure_mode)
+		release_firmware(isys->fw);
+	ipu_trace_uninit(&adev->dev);
+
+	mutex_destroy(&isys->mutex);
+	mutex_destroy(&isys->stream_mutex);
+
+	if (isys->short_packet_source == IPU_ISYS_SHORT_PACKET_FROM_TUNIT)
+		mutex_destroy(&isys->short_packet_tracing_mutex);
+
+	ipu_mmu_hw_cleanup(adev->mmu);
+
+	return rval;
+}
+
+struct fwmsg {
+	int type;
+	char *msg;
+	bool valid_ts;
+};
+
+static const struct fwmsg fw_msg[] = {
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_OPEN_DONE, "STREAM_OPEN_DONE", 0},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_CLOSE_ACK, "STREAM_CLOSE_ACK", 0},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_START_ACK, "STREAM_START_ACK", 0},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_START_AND_CAPTURE_ACK,
+	 "STREAM_START_AND_CAPTURE_ACK", 0},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_STOP_ACK, "STREAM_STOP_ACK", 0},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_FLUSH_ACK, "STREAM_FLUSH_ACK", 0},
+	{IPU_FW_ISYS_RESP_TYPE_PIN_DATA_READY, "PIN_DATA_READY", 1},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_ACK, "STREAM_CAPTURE_ACK", 0},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_START_AND_CAPTURE_DONE,
+	 "STREAM_START_AND_CAPTURE_DONE", 1},
+	{IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_DONE, "STREAM_CAPTURE_DONE", 1},
+	{IPU_FW_ISYS_RESP_TYPE_FRAME_SOF, "FRAME_SOF", 1},
+	{IPU_FW_ISYS_RESP_TYPE_FRAME_EOF, "FRAME_EOF", 1},
+	{IPU_FW_ISYS_RESP_TYPE_STATS_DATA_READY, "STATS_READY", 1},
+	{-1, "UNKNOWN MESSAGE", 0},
+};
+
+static int resp_type_to_index(int type)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(fw_msg); i++)
+		if (fw_msg[i].type == type)
+			return i;
+
+	return i - 1;
+}
+
+int isys_isr_one(struct ipu_bus_device *adev)
+{
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	struct ipu_fw_isys_resp_info_abi resp_data;
+	struct ipu_fw_isys_resp_info_abi *resp;
+	struct ipu_isys_pipeline *pipe;
+	u64 ts;
+	unsigned int i;
+
+	if (!isys->fwcom)
+		return 0;
+
+	resp = ipu_fw_isys_get_resp(isys->fwcom, IPU_BASE_MSG_RECV_QUEUES,
+				    &resp_data);
+	if (!resp)
+		return 1;
+
+	ts = (u64)resp->timestamp[1] << 32 | resp->timestamp[0];
+
+	if (resp->error_info.error == IPU_FW_ISYS_ERROR_STREAM_IN_SUSPENSION)
+		/* Suspension is kind of special case: not enough buffers */
+		dev_dbg(&adev->dev,
+			"hostlib: error resp %02d %s, stream %u, error SUSPENSION, details %d, timestamp 0x%16.16llx, pin %d\n",
+			resp->type,
+			fw_msg[resp_type_to_index(resp->type)].msg,
+			resp->stream_handle,
+			resp->error_info.error_details,
+			fw_msg[resp_type_to_index(resp->type)].valid_ts ?
+			ts : 0, resp->pin_id);
+	else if (resp->error_info.error)
+		dev_dbg(&adev->dev,
+			"hostlib: error resp %02d %s, stream %u, error %d, details %d, timestamp 0x%16.16llx, pin %d\n",
+			resp->type,
+			fw_msg[resp_type_to_index(resp->type)].msg,
+			resp->stream_handle,
+			resp->error_info.error, resp->error_info.error_details,
+			fw_msg[resp_type_to_index(resp->type)].valid_ts ?
+			ts : 0, resp->pin_id);
+	else
+		dev_dbg(&adev->dev,
+			"hostlib: resp %02d %s, stream %u, timestamp 0x%16.16llx, pin %d\n",
+			resp->type,
+			fw_msg[resp_type_to_index(resp->type)].msg,
+			resp->stream_handle,
+			fw_msg[resp_type_to_index(resp->type)].valid_ts ?
+			ts : 0, resp->pin_id);
+
+	if (resp->stream_handle >= IPU_ISYS_MAX_STREAMS) {
+		dev_err(&adev->dev, "bad stream handle %u\n",
+			resp->stream_handle);
+		goto leave;
+	}
+
+	pipe = isys->pipes[resp->stream_handle];
+	if (!pipe) {
+		dev_err(&adev->dev, "no pipeline for stream %u\n",
+			resp->stream_handle);
+		goto leave;
+	}
+	pipe->error = resp->error_info.error;
+
+	switch (resp->type) {
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_OPEN_DONE:
+		ipu_put_fw_mgs_buf(ipu_bus_get_drvdata(adev), resp->buf_id);
+		complete(&pipe->stream_open_completion);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_CLOSE_ACK:
+		complete(&pipe->stream_close_completion);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_START_ACK:
+		complete(&pipe->stream_start_completion);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_START_AND_CAPTURE_ACK:
+		ipu_put_fw_mgs_buf(ipu_bus_get_drvdata(adev), resp->buf_id);
+		complete(&pipe->stream_start_completion);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_STOP_ACK:
+		complete(&pipe->stream_stop_completion);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_FLUSH_ACK:
+		complete(&pipe->stream_stop_completion);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_PIN_DATA_READY:
+		if (resp->pin_id < IPU_ISYS_OUTPUT_PINS &&
+		    pipe->output_pins[resp->pin_id].pin_ready)
+			pipe->output_pins[resp->pin_id].pin_ready(pipe, resp);
+		else
+			dev_err(&adev->dev,
+				"%d:No data pin ready handler for pin id %d\n",
+				resp->stream_handle, resp->pin_id);
+		if (pipe->csi2)
+			ipu_isys_csi2_error(pipe->csi2);
+
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_ACK:
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_START_AND_CAPTURE_DONE:
+	case IPU_FW_ISYS_RESP_TYPE_STREAM_CAPTURE_DONE:
+		if (pipe->interlaced) {
+			struct ipu_isys_buffer *ib, *ib_safe;
+			struct list_head list;
+			unsigned long flags;
+			unsigned int *ts = resp->timestamp;
+
+			if (pipe->isys->short_packet_source ==
+			    IPU_ISYS_SHORT_PACKET_FROM_TUNIT)
+				pipe->cur_field =
+				    ipu_isys_csi2_get_current_field(pipe, ts);
+
+			/*
+			 * Move the pending buffers to a local temp list.
+			 * Then we do not need to handle the lock during
+			 * the loop.
+			 */
+			spin_lock_irqsave(&pipe->short_packet_queue_lock,
+					  flags);
+			list_cut_position(&list,
+					  &pipe->pending_interlaced_bufs,
+					  pipe->pending_interlaced_bufs.prev);
+			spin_unlock_irqrestore(&pipe->short_packet_queue_lock,
+					       flags);
+
+			list_for_each_entry_safe(ib, ib_safe, &list, head) {
+				struct vb2_buffer *vb;
+
+				vb = ipu_isys_buffer_to_vb2_buffer(ib);
+				to_vb2_v4l2_buffer(vb)->field = pipe->cur_field;
+				list_del(&ib->head);
+
+				ipu_isys_queue_buf_done(ib);
+			}
+		}
+		for (i = 0; i < IPU_NUM_CAPTURE_DONE; i++)
+			if (pipe->capture_done[i])
+				pipe->capture_done[i] (pipe, resp);
+
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_FRAME_SOF:
+		if (pipe->csi2)
+			ipu_isys_csi2_sof_event(pipe->csi2);
+
+		pipe->seq[pipe->seq_index].sequence =
+		    atomic_read(&pipe->sequence) - 1;
+		pipe->seq[pipe->seq_index].timestamp = ts;
+		dev_dbg(&adev->dev,
+			"sof: handle %d: (index %u), timestamp 0x%16.16llx\n",
+			resp->stream_handle,
+			pipe->seq[pipe->seq_index].sequence, ts);
+		pipe->seq_index = (pipe->seq_index + 1)
+		    % IPU_ISYS_MAX_PARALLEL_SOF;
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_FRAME_EOF:
+		if (pipe->csi2)
+			ipu_isys_csi2_eof_event(pipe->csi2);
+
+		dev_dbg(&adev->dev,
+			"eof: handle %d: (index %u), timestamp 0x%16.16llx\n",
+			resp->stream_handle,
+			pipe->seq[pipe->seq_index].sequence, ts);
+		break;
+	case IPU_FW_ISYS_RESP_TYPE_STATS_DATA_READY:
+		break;
+	default:
+		dev_err(&adev->dev, "%d:unknown response type %u\n",
+			resp->stream_handle, resp->type);
+		break;
+	}
+
+leave:
+	ipu_fw_isys_put_resp(isys->fwcom, IPU_BASE_MSG_RECV_QUEUES);
+	return 0;
+}
+
+static struct ipu_bus_driver isys_driver = {
+	.probe = isys_probe,
+	.remove = isys_remove,
+	.isr = isys_isr,
+	.wanted = IPU_ISYS_NAME,
+	.drv = {
+		.name = IPU_ISYS_NAME,
+		.owner = THIS_MODULE,
+		.pm = ISYS_PM_OPS,
+	},
+};
+
+module_ipu_bus_driver(isys_driver);
+
+static const struct pci_device_id ipu_pci_tbl[] = {
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6SE_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_ADL_P_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_ADL_N_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_RPL_P_PCI_ID)},
+	{0,}
+};
+MODULE_DEVICE_TABLE(pci, ipu_pci_tbl);
+
+MODULE_AUTHOR("Sakari Ailus <sakari.ailus@linux.intel.com>");
+MODULE_AUTHOR("Samu Onkalo <samu.onkalo@intel.com>");
+MODULE_AUTHOR("Jouni Högander <jouni.hogander@intel.com>");
+MODULE_AUTHOR("Jouni Ukkonen <jouni.ukkonen@intel.com>");
+MODULE_AUTHOR("Jianxu Zheng <jian.xu.zheng@intel.com>");
+MODULE_AUTHOR("Tianshu Qiu <tian.shu.qiu@intel.com>");
+MODULE_AUTHOR("Renwei Wu <renwei.wu@intel.com>");
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_AUTHOR("Yunliang Ding <yunliang.ding@intel.com>");
+MODULE_AUTHOR("Zaikuo Wang <zaikuo.wang@intel.com>");
+MODULE_AUTHOR("Leifu Zhao <leifu.zhao@intel.com>");
+MODULE_AUTHOR("Xia Wu <xia.wu@intel.com>");
+MODULE_AUTHOR("Kun Jiang <kun.jiang@intel.com>");
+MODULE_AUTHOR("Yu Xia <yu.y.xia@intel.com>");
+MODULE_AUTHOR("Jerry Hu <jerry.w.hu@intel.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel ipu input system driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-isys.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-isys.h
@@ -0,0 +1,227 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_ISYS_H
+#define IPU_ISYS_H
+
+#include <linux/pm_qos.h>
+#include <linux/spinlock.h>
+
+#include <media/v4l2-device.h>
+#include <media/media-device.h>
+
+#include <uapi/linux/ipu-isys.h>
+
+#include "ipu.h"
+#include "ipu-isys-media.h"
+#include "ipu-isys-csi2.h"
+#include "ipu-isys-csi2-be.h"
+#include "ipu-isys-video.h"
+#include "ipu-pdata.h"
+#include "ipu-fw-isys.h"
+#include "ipu-platform-isys.h"
+
+#define IPU_ISYS_2600_MEM_LINE_ALIGN	64
+
+/* for TPG */
+#define IPU_ISYS_FREQ		533000000UL
+
+/*
+ * Current message queue configuration. These must be big enough
+ * so that they never gets full. Queues are located in system memory
+ */
+#define IPU_ISYS_SIZE_RECV_QUEUE 40
+#define IPU_ISYS_SIZE_SEND_QUEUE 40
+#define IPU_ISYS_SIZE_PROXY_RECV_QUEUE 5
+#define IPU_ISYS_SIZE_PROXY_SEND_QUEUE 5
+#define IPU_ISYS_NUM_RECV_QUEUE 1
+
+/*
+ * Device close takes some time from last ack message to actual stopping
+ * of the SP processor. As long as the SP processor runs we can't proceed with
+ * clean up of resources.
+ */
+#define IPU_ISYS_OPEN_TIMEOUT_US		1000
+#define IPU_ISYS_OPEN_RETRY		1000
+#define IPU_ISYS_TURNOFF_DELAY_US		1000
+#define IPU_ISYS_TURNOFF_TIMEOUT		1000
+#define IPU_LIB_CALL_TIMEOUT_JIFFIES \
+	msecs_to_jiffies(IPU_LIB_CALL_TIMEOUT_MS)
+
+#define IPU_ISYS_CSI2_LONG_PACKET_HEADER_SIZE	32
+#define IPU_ISYS_CSI2_LONG_PACKET_FOOTER_SIZE	32
+
+#define IPU_ISYS_MIN_WIDTH		1U
+#define IPU_ISYS_MIN_HEIGHT		1U
+#define IPU_ISYS_MAX_WIDTH		16384U
+#define IPU_ISYS_MAX_HEIGHT		16384U
+
+#define NR_OF_CSI2_BE_SOC_DEV 1
+
+/* the threshold granularity is 2KB on IPU6 */
+#define IPU6_SRAM_GRANULRITY_SHIFT	11
+#define IPU6_SRAM_GRANULRITY_SIZE	2048
+/* the threshold granularity is 1KB on IPU6SE */
+#define IPU6SE_SRAM_GRANULRITY_SHIFT	10
+#define IPU6SE_SRAM_GRANULRITY_SIZE	1024
+
+struct task_struct;
+
+struct ltr_did {
+	union {
+		u32 value;
+		struct {
+			u8 val0;
+			u8 val1;
+			u8 val2;
+			u8 val3;
+		} bits;
+	} lut_ltr;
+	union {
+		u32 value;
+		struct {
+			u8 th0;
+			u8 th1;
+			u8 th2;
+			u8 th3;
+		} bits;
+	} lut_fill_time;
+};
+
+struct isys_iwake_watermark {
+	bool iwake_enabled;
+	bool force_iwake_disable;
+	u32 iwake_threshold;
+	u64 isys_pixelbuffer_datarate;
+	struct ltr_did ltrdid;
+	struct mutex mutex; /* protect whole struct */
+	struct ipu_isys *isys;
+	struct list_head video_list;
+};
+struct ipu_isys_sensor_info {
+	unsigned int vc1_data_start;
+	unsigned int vc1_data_end;
+	unsigned int vc0_data_start;
+	unsigned int vc0_data_end;
+	unsigned int vc1_pdaf_start;
+	unsigned int vc1_pdaf_end;
+	unsigned int sensor_metadata;
+};
+
+/*
+ * struct ipu_isys
+ *
+ * @media_dev: Media device
+ * @v4l2_dev: V4L2 device
+ * @adev: ISYS bus device
+ * @power: Is ISYS powered on or not?
+ * @isr_bits: Which bits does the ISR handle?
+ * @power_lock: Serialise access to power (power state in general)
+ * @csi2_rx_ctrl_cached: cached shared value between all CSI2 receivers
+ * @lock: serialise access to pipes
+ * @pipes: pipelines per stream ID
+ * @fwcom: fw communication layer private pointer
+ *         or optional external library private pointer
+ * @line_align: line alignment in memory
+ * @reset_needed: Isys requires d0i0->i3 transition
+ * @video_opened: total number of opened file handles on video nodes
+ * @mutex: serialise access isys video open/release related operations
+ * @stream_mutex: serialise stream start and stop, queueing requests
+ * @lib_mutex: optional external library mutex
+ * @pdata: platform data pointer
+ * @csi2: CSI-2 receivers
+ * @csi2_be: CSI-2 back-ends
+ * @fw: ISYS firmware binary (unsecure firmware)
+ * @fw_sgt: fw scatterlist
+ * @pkg_dir: host pointer to pkg_dir
+ * @pkg_dir_dma_addr: I/O virtual address for pkg_dir
+ * @pkg_dir_size: size of pkg_dir in bytes
+ * @short_packet_source: select short packet capture mode
+ */
+struct ipu_isys {
+	struct media_device media_dev;
+	struct v4l2_device v4l2_dev;
+	struct ipu_bus_device *adev;
+
+	int power;
+	spinlock_t power_lock;	/* Serialise access to power */
+	u32 isr_csi2_bits;
+	u32 csi2_rx_ctrl_cached;
+	spinlock_t lock;	/* Serialise access to pipes */
+	struct ipu_isys_pipeline *pipes[IPU_ISYS_MAX_STREAMS];
+	void *fwcom;
+	unsigned int line_align;
+	bool reset_needed;
+	bool icache_prefetch;
+	bool csi2_cse_ipc_not_supported;
+	unsigned int video_opened;
+	unsigned int stream_opened;
+	struct ipu_isys_sensor_info sensor_info;
+	unsigned int sensor_types[N_IPU_FW_ISYS_SENSOR_TYPE];
+
+#ifdef CONFIG_DEBUG_FS
+	struct dentry *debugfsdir;
+#endif
+	struct mutex mutex;	/* Serialise isys video open/release related */
+	struct mutex stream_mutex;	/* Stream start, stop, queueing reqs */
+	struct mutex lib_mutex;	/* Serialise optional external library mutex */
+
+	struct ipu_isys_pdata *pdata;
+
+	struct ipu_isys_csi2 *csi2;
+	struct ipu_isys_csi2_be csi2_be;
+	struct ipu_isys_csi2_be_soc csi2_be_soc[NR_OF_CSI2_BE_SOC_DEV];
+	const struct firmware *fw;
+	struct sg_table fw_sgt;
+
+	u64 *pkg_dir;
+	dma_addr_t pkg_dir_dma_addr;
+	unsigned int pkg_dir_size;
+
+	struct list_head requests;
+	struct pm_qos_request pm_qos;
+	unsigned int short_packet_source;
+	struct ipu_isys_csi2_monitor_message *short_packet_trace_buffer;
+	dma_addr_t short_packet_trace_buffer_dma_addr;
+	unsigned int short_packet_tracing_count;
+	struct mutex short_packet_tracing_mutex;	/* For tracing count */
+	u64 tsc_timer_base;
+	u64 tunit_timer_base;
+	spinlock_t listlock;	/* Protect framebuflist */
+	struct list_head framebuflist;
+	struct list_head framebuflist_fw;
+	struct v4l2_async_notifier notifier;
+	struct isys_iwake_watermark *iwake_watermark;
+
+};
+
+void update_watermark_setting(struct ipu_isys *isys);
+
+struct isys_fw_msgs {
+	union {
+		u64 dummy;
+		struct ipu_fw_isys_frame_buff_set_abi frame;
+		struct ipu_fw_isys_stream_cfg_data_abi stream;
+	} fw_msg;
+	struct list_head head;
+	dma_addr_t dma_addr;
+};
+
+#define to_frame_msg_buf(a) (&(a)->fw_msg.frame)
+#define to_stream_cfg_msg_buf(a) (&(a)->fw_msg.stream)
+#define to_dma_addr(a) ((a)->dma_addr)
+
+struct isys_fw_msgs *ipu_get_fw_msg_buf(struct ipu_isys_pipeline *ip);
+void ipu_put_fw_mgs_buf(struct ipu_isys *isys, u64 data);
+void ipu_cleanup_fw_msg_bufs(struct ipu_isys *isys);
+
+extern const struct v4l2_ioctl_ops ipu_isys_ioctl_ops;
+
+void isys_setup_hw(struct ipu_isys *isys);
+int isys_isr_one(struct ipu_bus_device *adev);
+irqreturn_t isys_isr(struct ipu_bus_device *adev);
+#ifdef IPU_ISYS_GPC
+int ipu_isys_gpc_init_debugfs(struct ipu_isys *isys);
+#endif
+
+#endif /* IPU_ISYS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-mmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-mmu.c
@@ -0,0 +1,858 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2021 Intel Corporation
+
+#include <asm/cacheflush.h>
+
+#include <linux/device.h>
+#include <linux/iova.h>
+#include <linux/module.h>
+#include <linux/sizes.h>
+
+#include "ipu.h"
+#include "ipu-platform.h"
+#include "ipu-dma.h"
+#include "ipu-mmu.h"
+#include "ipu-platform-regs.h"
+
+#define ISP_PAGE_SHIFT		12
+#define ISP_PAGE_SIZE		BIT(ISP_PAGE_SHIFT)
+#define ISP_PAGE_MASK		(~(ISP_PAGE_SIZE - 1))
+
+#define ISP_L1PT_SHIFT		22
+#define ISP_L1PT_MASK		(~((1U << ISP_L1PT_SHIFT) - 1))
+
+#define ISP_L2PT_SHIFT		12
+#define ISP_L2PT_MASK		(~(ISP_L1PT_MASK | (~(ISP_PAGE_MASK))))
+
+#define ISP_L1PT_PTES           1024
+#define ISP_L2PT_PTES           1024
+
+#define ISP_PADDR_SHIFT		12
+
+#define REG_TLB_INVALIDATE	0x0000
+
+#define REG_L1_PHYS		0x0004	/* 27-bit pfn */
+#define REG_INFO		0x0008
+
+/* The range of stream ID i in L1 cache is from 0 to 15 */
+#define MMUV2_REG_L1_STREAMID(i)	(0x0c + ((i) * 4))
+
+/* The range of stream ID i in L2 cache is from 0 to 15 */
+#define MMUV2_REG_L2_STREAMID(i)	(0x4c + ((i) * 4))
+
+#define TBL_PHYS_ADDR(a)	((phys_addr_t)(a) << ISP_PADDR_SHIFT)
+
+static void tlb_invalidate(struct ipu_mmu *mmu)
+{
+	unsigned int i;
+	unsigned long flags;
+
+	spin_lock_irqsave(&mmu->ready_lock, flags);
+	if (!mmu->ready) {
+		spin_unlock_irqrestore(&mmu->ready_lock, flags);
+		return;
+	}
+
+	for (i = 0; i < mmu->nr_mmus; i++) {
+		/*
+		 * To avoid the HW bug induced dead lock in some of the IPU
+		 * MMUs on successive invalidate calls, we need to first do a
+		 * read to the page table base before writing the invalidate
+		 * register. MMUs which need to implement this WA, will have
+		 * the insert_read_before_invalidate flags set as true.
+		 * Disregard the return value of the read.
+		 */
+		if (mmu->mmu_hw[i].insert_read_before_invalidate)
+			readl(mmu->mmu_hw[i].base + REG_L1_PHYS);
+
+		writel(0xffffffff, mmu->mmu_hw[i].base +
+		       REG_TLB_INVALIDATE);
+		/*
+		 * The TLB invalidation is a "single cycle" (IOMMU clock cycles)
+		 * When the actual MMIO write reaches the IPU TLB Invalidate
+		 * register, wmb() will force the TLB invalidate out if the CPU
+		 * attempts to update the IOMMU page table (or sooner).
+		 */
+		wmb();
+	}
+	spin_unlock_irqrestore(&mmu->ready_lock, flags);
+}
+
+#ifdef DEBUG
+static void page_table_dump(struct ipu_mmu_info *mmu_info)
+{
+	u32 l1_idx;
+
+	dev_dbg(mmu_info->dev, "begin IOMMU page table dump\n");
+
+	for (l1_idx = 0; l1_idx < ISP_L1PT_PTES; l1_idx++) {
+		u32 l2_idx;
+		u32 iova = (phys_addr_t)l1_idx << ISP_L1PT_SHIFT;
+
+		if (mmu_info->l1_pt[l1_idx] == mmu_info->dummy_l2_pteval)
+			continue;
+		dev_dbg(mmu_info->dev,
+			"l1 entry %u; iovas 0x%8.8x-0x%8.8x, at %p\n",
+			l1_idx, iova, iova + ISP_PAGE_SIZE,
+			(void *)TBL_PHYS_ADDR(mmu_info->l1_pt[l1_idx]));
+
+		for (l2_idx = 0; l2_idx < ISP_L2PT_PTES; l2_idx++) {
+			u32 *l2_pt = mmu_info->l2_pts[l1_idx];
+			u32 iova2 = iova + (l2_idx << ISP_L2PT_SHIFT);
+
+			if (l2_pt[l2_idx] == mmu_info->dummy_page_pteval)
+				continue;
+
+			dev_dbg(mmu_info->dev,
+				"\tl2 entry %u; iova 0x%8.8x, phys %p\n",
+				l2_idx, iova2,
+				(void *)TBL_PHYS_ADDR(l2_pt[l2_idx]));
+		}
+	}
+
+	dev_dbg(mmu_info->dev, "end IOMMU page table dump\n");
+}
+#endif /* DEBUG */
+
+static dma_addr_t map_single(struct ipu_mmu_info *mmu_info, void *ptr)
+{
+	dma_addr_t dma;
+
+	dma = dma_map_single(mmu_info->dev, ptr, PAGE_SIZE, DMA_BIDIRECTIONAL);
+	if (dma_mapping_error(mmu_info->dev, dma))
+		return 0;
+
+	return dma;
+}
+
+static int get_dummy_page(struct ipu_mmu_info *mmu_info)
+{
+	dma_addr_t dma;
+	void *pt = (void *)get_zeroed_page(GFP_ATOMIC | GFP_DMA32);
+
+	if (!pt)
+		return -ENOMEM;
+
+	dev_dbg(mmu_info->dev, "%s get_zeroed_page() == %p\n", __func__, pt);
+
+	dma = map_single(mmu_info, pt);
+	if (!dma) {
+		dev_err(mmu_info->dev, "Failed to map dummy page\n");
+		goto err_free_page;
+	}
+
+	mmu_info->dummy_page = pt;
+	mmu_info->dummy_page_pteval = dma >> ISP_PAGE_SHIFT;
+
+	return 0;
+
+err_free_page:
+	free_page((unsigned long)pt);
+	return -ENOMEM;
+}
+
+static void free_dummy_page(struct ipu_mmu_info *mmu_info)
+{
+	dma_unmap_single(mmu_info->dev,
+			 TBL_PHYS_ADDR(mmu_info->dummy_page_pteval),
+			 PAGE_SIZE, DMA_BIDIRECTIONAL);
+	free_page((unsigned long)mmu_info->dummy_page);
+}
+
+static int alloc_dummy_l2_pt(struct ipu_mmu_info *mmu_info)
+{
+	dma_addr_t dma;
+	u32 *pt = (u32 *)get_zeroed_page(GFP_ATOMIC | GFP_DMA32);
+	int i;
+
+	if (!pt)
+		return -ENOMEM;
+
+	dev_dbg(mmu_info->dev, "%s get_zeroed_page() == %p\n", __func__, pt);
+
+	dma = map_single(mmu_info, pt);
+	if (!dma) {
+		dev_err(mmu_info->dev, "Failed to map l2pt page\n");
+		goto err_free_page;
+	}
+
+	for (i = 0; i < ISP_L2PT_PTES; i++)
+		pt[i] = mmu_info->dummy_page_pteval;
+
+	mmu_info->dummy_l2_pt = pt;
+	mmu_info->dummy_l2_pteval = dma >> ISP_PAGE_SHIFT;
+
+	return 0;
+
+err_free_page:
+	free_page((unsigned long)pt);
+	return -ENOMEM;
+}
+
+static void free_dummy_l2_pt(struct ipu_mmu_info *mmu_info)
+{
+	dma_unmap_single(mmu_info->dev,
+			 TBL_PHYS_ADDR(mmu_info->dummy_l2_pteval),
+			 PAGE_SIZE, DMA_BIDIRECTIONAL);
+	free_page((unsigned long)mmu_info->dummy_l2_pt);
+}
+
+static u32 *alloc_l1_pt(struct ipu_mmu_info *mmu_info)
+{
+	dma_addr_t dma;
+	u32 *pt = (u32 *)get_zeroed_page(GFP_ATOMIC | GFP_DMA32);
+	int i;
+
+	if (!pt)
+		return NULL;
+
+	dev_dbg(mmu_info->dev, "%s get_zeroed_page() == %p\n", __func__, pt);
+
+	for (i = 0; i < ISP_L1PT_PTES; i++)
+		pt[i] = mmu_info->dummy_l2_pteval;
+
+	dma = map_single(mmu_info, pt);
+	if (!dma) {
+		dev_err(mmu_info->dev, "Failed to map l1pt page\n");
+		goto err_free_page;
+	}
+
+	mmu_info->l1_pt_dma = dma >> ISP_PADDR_SHIFT;
+	dev_dbg(mmu_info->dev, "l1 pt %p mapped at %llx\n", pt, dma);
+
+	return pt;
+
+err_free_page:
+	free_page((unsigned long)pt);
+	return NULL;
+}
+
+static u32 *alloc_l2_pt(struct ipu_mmu_info *mmu_info)
+{
+	u32 *pt = (u32 *)get_zeroed_page(GFP_ATOMIC | GFP_DMA32);
+	int i;
+
+	if (!pt)
+		return NULL;
+
+	dev_dbg(mmu_info->dev, "%s get_zeroed_page() == %p\n", __func__, pt);
+
+	for (i = 0; i < ISP_L1PT_PTES; i++)
+		pt[i] = mmu_info->dummy_page_pteval;
+
+	return pt;
+}
+
+static int l2_map(struct ipu_mmu_info *mmu_info, unsigned long iova,
+		  phys_addr_t paddr, size_t size)
+{
+	u32 l1_idx = iova >> ISP_L1PT_SHIFT;
+	u32 l1_entry;
+	u32 *l2_pt, *l2_virt;
+	u32 iova_start = iova;
+	unsigned int l2_idx;
+	unsigned long flags;
+	dma_addr_t dma;
+
+	dev_dbg(mmu_info->dev,
+		"mapping l2 page table for l1 index %u (iova %8.8x)\n",
+		l1_idx, (u32)iova);
+
+	spin_lock_irqsave(&mmu_info->lock, flags);
+	l1_entry = mmu_info->l1_pt[l1_idx];
+	if (l1_entry == mmu_info->dummy_l2_pteval) {
+		l2_virt = mmu_info->l2_pts[l1_idx];
+		if (likely(!l2_virt)) {
+			l2_virt = alloc_l2_pt(mmu_info);
+			if (!l2_virt) {
+				spin_unlock_irqrestore(&mmu_info->lock, flags);
+				return -ENOMEM;
+			}
+		}
+
+		dma = map_single(mmu_info, l2_virt);
+		if (!dma) {
+			dev_err(mmu_info->dev, "Failed to map l2pt page\n");
+			free_page((unsigned long)l2_virt);
+			spin_unlock_irqrestore(&mmu_info->lock, flags);
+			return -EINVAL;
+		}
+
+		l1_entry = dma >> ISP_PADDR_SHIFT;
+
+		dev_dbg(mmu_info->dev, "page for l1_idx %u %p allocated\n",
+			l1_idx, l2_virt);
+		mmu_info->l1_pt[l1_idx] = l1_entry;
+		mmu_info->l2_pts[l1_idx] = l2_virt;
+		clflush_cache_range(&mmu_info->l1_pt[l1_idx],
+				    sizeof(mmu_info->l1_pt[l1_idx]));
+	}
+
+	l2_pt = mmu_info->l2_pts[l1_idx];
+
+	dev_dbg(mmu_info->dev, "l2_pt at %p with dma 0x%x\n", l2_pt, l1_entry);
+
+	paddr = ALIGN(paddr, ISP_PAGE_SIZE);
+
+	l2_idx = (iova_start & ISP_L2PT_MASK) >> ISP_L2PT_SHIFT;
+
+	dev_dbg(mmu_info->dev, "l2_idx %u, phys 0x%8.8x\n", l2_idx,
+		l2_pt[l2_idx]);
+	if (l2_pt[l2_idx] != mmu_info->dummy_page_pteval) {
+		spin_unlock_irqrestore(&mmu_info->lock, flags);
+		return -EINVAL;
+	}
+
+	l2_pt[l2_idx] = paddr >> ISP_PADDR_SHIFT;
+
+	clflush_cache_range(&l2_pt[l2_idx], sizeof(l2_pt[l2_idx]));
+	spin_unlock_irqrestore(&mmu_info->lock, flags);
+
+	dev_dbg(mmu_info->dev, "l2 index %u mapped as 0x%8.8x\n", l2_idx,
+		l2_pt[l2_idx]);
+
+	return 0;
+}
+
+static int __ipu_mmu_map(struct ipu_mmu_info *mmu_info, unsigned long iova,
+			 phys_addr_t paddr, size_t size)
+{
+	u32 iova_start = round_down(iova, ISP_PAGE_SIZE);
+	u32 iova_end = ALIGN(iova + size, ISP_PAGE_SIZE);
+
+	dev_dbg(mmu_info->dev,
+		"mapping iova 0x%8.8x--0x%8.8x, size %zu at paddr 0x%10.10llx\n",
+		iova_start, iova_end, size, paddr);
+
+	return l2_map(mmu_info, iova_start, paddr, size);
+}
+
+static size_t l2_unmap(struct ipu_mmu_info *mmu_info, unsigned long iova,
+		       phys_addr_t dummy, size_t size)
+{
+	u32 l1_idx = iova >> ISP_L1PT_SHIFT;
+	u32 *l2_pt;
+	u32 iova_start = iova;
+	unsigned int l2_idx;
+	size_t unmapped = 0;
+	unsigned long flags;
+
+	dev_dbg(mmu_info->dev, "unmapping l2 page table for l1 index %u (iova 0x%8.8lx)\n",
+		l1_idx, iova);
+
+	spin_lock_irqsave(&mmu_info->lock, flags);
+	if (mmu_info->l1_pt[l1_idx] == mmu_info->dummy_l2_pteval) {
+		spin_unlock_irqrestore(&mmu_info->lock, flags);
+		dev_err(mmu_info->dev,
+			"unmap iova 0x%8.8lx l1 idx %u which was not mapped\n",
+			iova, l1_idx);
+		return 0;
+	}
+
+	for (l2_idx = (iova_start & ISP_L2PT_MASK) >> ISP_L2PT_SHIFT;
+	     (iova_start & ISP_L1PT_MASK) + (l2_idx << ISP_PAGE_SHIFT)
+	     < iova_start + size && l2_idx < ISP_L2PT_PTES; l2_idx++) {
+		l2_pt = mmu_info->l2_pts[l1_idx];
+		dev_dbg(mmu_info->dev,
+			"unmap l2 index %u with pteval 0x%10.10llx\n",
+			l2_idx, TBL_PHYS_ADDR(l2_pt[l2_idx]));
+		l2_pt[l2_idx] = mmu_info->dummy_page_pteval;
+
+		clflush_cache_range(&l2_pt[l2_idx], sizeof(l2_pt[l2_idx]));
+		unmapped++;
+	}
+	spin_unlock_irqrestore(&mmu_info->lock, flags);
+
+	return unmapped << ISP_PAGE_SHIFT;
+}
+
+static size_t __ipu_mmu_unmap(struct ipu_mmu_info *mmu_info,
+			      unsigned long iova, size_t size)
+{
+	return l2_unmap(mmu_info, iova, 0, size);
+}
+
+static int allocate_trash_buffer(struct ipu_mmu *mmu)
+{
+	unsigned int n_pages = PAGE_ALIGN(IPU_MMUV2_TRASH_RANGE) >> PAGE_SHIFT;
+	struct iova *iova;
+	u32 iova_addr;
+	unsigned int i;
+	dma_addr_t dma;
+	int ret;
+
+	/* Allocate 8MB in iova range */
+	iova = alloc_iova(&mmu->dmap->iovad, n_pages,
+			  mmu->dmap->mmu_info->aperture_end >> PAGE_SHIFT, 0);
+	if (!iova) {
+		dev_err(mmu->dev, "cannot allocate iova range for trash\n");
+		return -ENOMEM;
+	}
+
+	dma = dma_map_page(mmu->dmap->mmu_info->dev, mmu->trash_page, 0,
+			   PAGE_SIZE, DMA_BIDIRECTIONAL);
+	if (dma_mapping_error(mmu->dmap->mmu_info->dev, dma)) {
+		dev_err(mmu->dmap->mmu_info->dev, "Failed to map trash page\n");
+		ret = -ENOMEM;
+		goto out_free_iova;
+	}
+
+	mmu->pci_trash_page = dma;
+
+	/*
+	 * Map the 8MB iova address range to the same physical trash page
+	 * mmu->trash_page which is already reserved at the probe
+	 */
+	iova_addr = iova->pfn_lo;
+	for (i = 0; i < n_pages; i++) {
+		ret = ipu_mmu_map(mmu->dmap->mmu_info, iova_addr << PAGE_SHIFT,
+				  mmu->pci_trash_page, PAGE_SIZE);
+		if (ret) {
+			dev_err(mmu->dev,
+				"mapping trash buffer range failed\n");
+			goto out_unmap;
+		}
+
+		iova_addr++;
+	}
+
+	mmu->iova_trash_page = iova->pfn_lo << PAGE_SHIFT;
+	dev_dbg(mmu->dev, "iova trash buffer for MMUID: %d is %u\n",
+		mmu->mmid, (unsigned int)mmu->iova_trash_page);
+	return 0;
+
+out_unmap:
+	ipu_mmu_unmap(mmu->dmap->mmu_info, iova->pfn_lo << PAGE_SHIFT,
+		      (iova->pfn_hi - iova->pfn_lo + 1) << PAGE_SHIFT);
+	dma_unmap_page(mmu->dmap->mmu_info->dev, mmu->pci_trash_page,
+		       PAGE_SIZE, DMA_BIDIRECTIONAL);
+out_free_iova:
+	__free_iova(&mmu->dmap->iovad, iova);
+	return ret;
+}
+
+int ipu_mmu_hw_init(struct ipu_mmu *mmu)
+{
+	unsigned int i;
+	unsigned long flags;
+	struct ipu_mmu_info *mmu_info;
+
+	dev_dbg(mmu->dev, "mmu hw init\n");
+
+	mmu_info = mmu->dmap->mmu_info;
+
+	/* Initialise the each MMU HW block */
+	for (i = 0; i < mmu->nr_mmus; i++) {
+		struct ipu_mmu_hw *mmu_hw = &mmu->mmu_hw[i];
+		unsigned int j;
+		u16 block_addr;
+
+		/* Write page table address per MMU */
+		writel((phys_addr_t)mmu_info->l1_pt_dma,
+		       mmu->mmu_hw[i].base + REG_L1_PHYS);
+
+		/* Set info bits per MMU */
+		writel(mmu->mmu_hw[i].info_bits,
+		       mmu->mmu_hw[i].base + REG_INFO);
+
+		/* Configure MMU TLB stream configuration for L1 */
+		for (j = 0, block_addr = 0; j < mmu_hw->nr_l1streams;
+		     block_addr += mmu->mmu_hw[i].l1_block_sz[j], j++) {
+			if (block_addr > IPU_MAX_LI_BLOCK_ADDR) {
+				dev_err(mmu->dev, "invalid L1 configuration\n");
+				return -EINVAL;
+			}
+
+			/* Write block start address for each streams */
+			writel(block_addr, mmu_hw->base +
+				   mmu_hw->l1_stream_id_reg_offset + 4 * j);
+		}
+
+		/* Configure MMU TLB stream configuration for L2 */
+		for (j = 0, block_addr = 0; j < mmu_hw->nr_l2streams;
+		     block_addr += mmu->mmu_hw[i].l2_block_sz[j], j++) {
+			if (block_addr > IPU_MAX_L2_BLOCK_ADDR) {
+				dev_err(mmu->dev, "invalid L2 configuration\n");
+				return -EINVAL;
+			}
+
+			writel(block_addr, mmu_hw->base +
+				   mmu_hw->l2_stream_id_reg_offset + 4 * j);
+		}
+	}
+
+	if (!mmu->trash_page) {
+		int ret;
+
+		mmu->trash_page = alloc_page(GFP_KERNEL);
+		if (!mmu->trash_page) {
+			dev_err(mmu->dev, "insufficient memory for trash buffer\n");
+			return -ENOMEM;
+		}
+
+		ret = allocate_trash_buffer(mmu);
+		if (ret) {
+			__free_page(mmu->trash_page);
+			mmu->trash_page = NULL;
+			dev_err(mmu->dev, "trash buffer allocation failed\n");
+			return ret;
+		}
+	}
+
+	spin_lock_irqsave(&mmu->ready_lock, flags);
+	mmu->ready = true;
+	spin_unlock_irqrestore(&mmu->ready_lock, flags);
+
+	return 0;
+}
+EXPORT_SYMBOL(ipu_mmu_hw_init);
+
+static struct ipu_mmu_info *ipu_mmu_alloc(struct ipu_device *isp)
+{
+	struct ipu_mmu_info *mmu_info;
+	int ret;
+
+	mmu_info = kzalloc(sizeof(*mmu_info), GFP_KERNEL);
+	if (!mmu_info)
+		return NULL;
+
+	mmu_info->aperture_start = 0;
+	mmu_info->aperture_end = DMA_BIT_MASK(isp->secure_mode ?
+					      IPU_MMU_ADDRESS_BITS :
+					      IPU_MMU_ADDRESS_BITS_NON_SECURE);
+	mmu_info->pgsize_bitmap = SZ_4K;
+	mmu_info->dev = &isp->pdev->dev;
+
+	ret = get_dummy_page(mmu_info);
+	if (ret)
+		goto err_free_info;
+
+	ret = alloc_dummy_l2_pt(mmu_info);
+	if (ret)
+		goto err_free_dummy_page;
+
+	mmu_info->l2_pts = vzalloc(ISP_L2PT_PTES * sizeof(*mmu_info->l2_pts));
+	if (!mmu_info->l2_pts)
+		goto err_free_dummy_l2_pt;
+
+	/*
+	 * We always map the L1 page table (a single page as well as
+	 * the L2 page tables).
+	 */
+	mmu_info->l1_pt = alloc_l1_pt(mmu_info);
+	if (!mmu_info->l1_pt)
+		goto err_free_l2_pts;
+
+	spin_lock_init(&mmu_info->lock);
+
+	dev_dbg(mmu_info->dev, "domain initialised\n");
+
+	return mmu_info;
+
+err_free_l2_pts:
+	vfree(mmu_info->l2_pts);
+err_free_dummy_l2_pt:
+	free_dummy_l2_pt(mmu_info);
+err_free_dummy_page:
+	free_dummy_page(mmu_info);
+err_free_info:
+	kfree(mmu_info);
+
+	return NULL;
+}
+
+int ipu_mmu_hw_cleanup(struct ipu_mmu *mmu)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&mmu->ready_lock, flags);
+	mmu->ready = false;
+	spin_unlock_irqrestore(&mmu->ready_lock, flags);
+
+	return 0;
+}
+EXPORT_SYMBOL(ipu_mmu_hw_cleanup);
+
+static struct ipu_dma_mapping *alloc_dma_mapping(struct ipu_device *isp)
+{
+	struct ipu_dma_mapping *dmap;
+
+	dmap = kzalloc(sizeof(*dmap), GFP_KERNEL);
+	if (!dmap)
+		return NULL;
+
+	dmap->mmu_info = ipu_mmu_alloc(isp);
+	if (!dmap->mmu_info) {
+		kfree(dmap);
+		return NULL;
+	}
+	init_iova_domain(&dmap->iovad, SZ_4K, 1);
+	dmap->mmu_info->dmap = dmap;
+
+	kref_init(&dmap->ref);
+
+	dev_dbg(&isp->pdev->dev, "alloc mapping\n");
+
+	iova_cache_get();
+
+	return dmap;
+}
+
+phys_addr_t ipu_mmu_iova_to_phys(struct ipu_mmu_info *mmu_info,
+				 dma_addr_t iova)
+{
+	unsigned long flags;
+	u32 *l2_pt;
+	phys_addr_t phy_addr;
+
+	spin_lock_irqsave(&mmu_info->lock, flags);
+	l2_pt = mmu_info->l2_pts[iova >> ISP_L1PT_SHIFT];
+	phy_addr = (phys_addr_t)l2_pt[(iova & ISP_L2PT_MASK) >> ISP_L2PT_SHIFT];
+	phy_addr <<= ISP_PAGE_SHIFT;
+	spin_unlock_irqrestore(&mmu_info->lock, flags);
+
+	return phy_addr;
+}
+
+/*
+ * The following four functions are implemented based on iommu.c
+ * drivers/iommu/iommu.c:iommu_pgsize().
+ */
+static size_t ipu_mmu_pgsize(unsigned long pgsize_bitmap,
+			     unsigned long addr_merge, size_t size)
+{
+	unsigned int pgsize_idx;
+	size_t pgsize;
+
+	/* Max page size that still fits into 'size' */
+	pgsize_idx = __fls(size);
+
+	/* need to consider alignment requirements ? */
+	if (likely(addr_merge)) {
+		/* Max page size allowed by address */
+		unsigned int align_pgsize_idx = __ffs(addr_merge);
+
+		pgsize_idx = min(pgsize_idx, align_pgsize_idx);
+	}
+
+	/* build a mask of acceptable page sizes */
+	pgsize = (1UL << (pgsize_idx + 1)) - 1;
+
+	/* throw away page sizes not supported by the hardware */
+	pgsize &= pgsize_bitmap;
+
+	/* make sure we're still sane */
+	WARN_ON(!pgsize);
+
+	/* pick the biggest page */
+	pgsize_idx = __fls(pgsize);
+	pgsize = 1UL << pgsize_idx;
+
+	return pgsize;
+}
+
+/* drivers/iommu/iommu.c:iommu_unmap() */
+size_t ipu_mmu_unmap(struct ipu_mmu_info *mmu_info, unsigned long iova,
+		     size_t size)
+{
+	size_t unmapped_page, unmapped = 0;
+	unsigned int min_pagesz;
+
+	/* find out the minimum page size supported */
+	min_pagesz = 1 << __ffs(mmu_info->pgsize_bitmap);
+
+	/*
+	 * The virtual address, as well as the size of the mapping, must be
+	 * aligned (at least) to the size of the smallest page supported
+	 * by the hardware
+	 */
+	if (!IS_ALIGNED(iova | size, min_pagesz)) {
+		dev_err(NULL, "unaligned: iova 0x%lx size 0x%zx min_pagesz 0x%x\n",
+			iova, size, min_pagesz);
+		return -EINVAL;
+	}
+
+	/*
+	 * Keep iterating until we either unmap 'size' bytes (or more)
+	 * or we hit an area that isn't mapped.
+	 */
+	while (unmapped < size) {
+		size_t pgsize = ipu_mmu_pgsize(mmu_info->pgsize_bitmap,
+						iova, size - unmapped);
+
+		unmapped_page = __ipu_mmu_unmap(mmu_info, iova, pgsize);
+		if (!unmapped_page)
+			break;
+
+		dev_dbg(mmu_info->dev, "unmapped: iova 0x%lx size 0x%zx\n",
+			iova, unmapped_page);
+
+		iova += unmapped_page;
+		unmapped += unmapped_page;
+	}
+
+	return unmapped;
+}
+
+/* drivers/iommu/iommu.c:iommu_map() */
+int ipu_mmu_map(struct ipu_mmu_info *mmu_info, unsigned long iova,
+		phys_addr_t paddr, size_t size)
+{
+	unsigned long orig_iova = iova;
+	unsigned int min_pagesz;
+	size_t orig_size = size;
+	int ret = 0;
+
+	if (mmu_info->pgsize_bitmap == 0UL)
+		return -ENODEV;
+
+	/* find out the minimum page size supported */
+	min_pagesz = 1 << __ffs(mmu_info->pgsize_bitmap);
+
+	/*
+	 * both the virtual address and the physical one, as well as
+	 * the size of the mapping, must be aligned (at least) to the
+	 * size of the smallest page supported by the hardware
+	 */
+	if (!IS_ALIGNED(iova | paddr | size, min_pagesz)) {
+		dev_err(mmu_info->dev,
+			"unaligned: iova 0x%lx pa %pa size 0x%zx min_pagesz 0x%x\n",
+			iova, &paddr, size, min_pagesz);
+		return -EINVAL;
+	}
+
+	dev_dbg(mmu_info->dev, "map: iova 0x%lx pa %pa size 0x%zx\n",
+		iova, &paddr, size);
+
+	while (size) {
+		size_t pgsize = ipu_mmu_pgsize(mmu_info->pgsize_bitmap,
+					       iova | paddr, size);
+
+		dev_dbg(mmu_info->dev,
+			"mapping: iova 0x%lx pa %pa pgsize 0x%zx\n",
+			iova, &paddr, pgsize);
+
+		ret = __ipu_mmu_map(mmu_info, iova, paddr, pgsize);
+		if (ret)
+			break;
+
+		iova += pgsize;
+		paddr += pgsize;
+		size -= pgsize;
+	}
+
+	/* unroll mapping in case something went wrong */
+	if (ret)
+		ipu_mmu_unmap(mmu_info, orig_iova, orig_size - size);
+
+	return ret;
+}
+
+static void ipu_mmu_destroy(struct ipu_mmu *mmu)
+{
+	struct ipu_dma_mapping *dmap = mmu->dmap;
+	struct ipu_mmu_info *mmu_info = dmap->mmu_info;
+	struct iova *iova;
+	u32 l1_idx;
+
+	if (mmu->iova_trash_page) {
+		iova = find_iova(&dmap->iovad,
+				 mmu->iova_trash_page >> PAGE_SHIFT);
+		if (iova) {
+			/* unmap and free the trash buffer iova */
+			ipu_mmu_unmap(mmu_info, iova->pfn_lo << PAGE_SHIFT,
+				      (iova->pfn_hi - iova->pfn_lo + 1) <<
+				      PAGE_SHIFT);
+			__free_iova(&dmap->iovad, iova);
+		} else {
+			dev_err(mmu->dev, "trash buffer iova not found.\n");
+		}
+
+		mmu->iova_trash_page = 0;
+		dma_unmap_page(mmu_info->dev, mmu->pci_trash_page,
+			       PAGE_SIZE, DMA_BIDIRECTIONAL);
+		mmu->pci_trash_page = 0;
+		__free_page(mmu->trash_page);
+	}
+
+	for (l1_idx = 0; l1_idx < ISP_L1PT_PTES; l1_idx++) {
+		if (mmu_info->l1_pt[l1_idx] != mmu_info->dummy_l2_pteval) {
+			dma_unmap_single(mmu_info->dev,
+					 TBL_PHYS_ADDR(mmu_info->l1_pt[l1_idx]),
+					 PAGE_SIZE, DMA_BIDIRECTIONAL);
+			free_page((unsigned long)mmu_info->l2_pts[l1_idx]);
+		}
+	}
+
+	free_dummy_page(mmu_info);
+	dma_unmap_single(mmu_info->dev, mmu_info->l1_pt_dma << ISP_PADDR_SHIFT,
+			 PAGE_SIZE, DMA_BIDIRECTIONAL);
+	free_page((unsigned long)mmu_info->dummy_l2_pt);
+	free_page((unsigned long)mmu_info->l1_pt);
+	kfree(mmu_info);
+}
+
+struct ipu_mmu *ipu_mmu_init(struct device *dev,
+			     void __iomem *base, int mmid,
+			     const struct ipu_hw_variants *hw)
+{
+	struct ipu_mmu *mmu;
+	struct ipu_mmu_pdata *pdata;
+	struct ipu_device *isp = pci_get_drvdata(to_pci_dev(dev));
+	unsigned int i;
+
+	if (hw->nr_mmus > IPU_MMU_MAX_DEVICES)
+		return ERR_PTR(-EINVAL);
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return ERR_PTR(-ENOMEM);
+
+	for (i = 0; i < hw->nr_mmus; i++) {
+		struct ipu_mmu_hw *pdata_mmu = &pdata->mmu_hw[i];
+		const struct ipu_mmu_hw *src_mmu = &hw->mmu_hw[i];
+
+		if (src_mmu->nr_l1streams > IPU_MMU_MAX_TLB_L1_STREAMS ||
+		    src_mmu->nr_l2streams > IPU_MMU_MAX_TLB_L2_STREAMS)
+			return ERR_PTR(-EINVAL);
+
+		*pdata_mmu = *src_mmu;
+		pdata_mmu->base = base + src_mmu->offset;
+	}
+
+	mmu = devm_kzalloc(dev, sizeof(*mmu), GFP_KERNEL);
+	if (!mmu)
+		return ERR_PTR(-ENOMEM);
+
+	mmu->mmid = mmid;
+	mmu->mmu_hw = pdata->mmu_hw;
+	mmu->nr_mmus = hw->nr_mmus;
+	mmu->tlb_invalidate = tlb_invalidate;
+	mmu->ready = false;
+	INIT_LIST_HEAD(&mmu->vma_list);
+	spin_lock_init(&mmu->ready_lock);
+
+	mmu->dmap = alloc_dma_mapping(isp);
+	if (!mmu->dmap) {
+		dev_err(dev, "can't alloc dma mapping\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	return mmu;
+}
+
+void ipu_mmu_cleanup(struct ipu_mmu *mmu)
+{
+	struct ipu_dma_mapping *dmap = mmu->dmap;
+
+	ipu_mmu_destroy(mmu);
+	mmu->dmap = NULL;
+	iova_cache_put();
+	put_iova_domain(&dmap->iovad);
+	kfree(dmap);
+}
+
+MODULE_AUTHOR("Sakari Ailus <sakari.ailus@linux.intel.com>");
+MODULE_AUTHOR("Samu Onkalo <samu.onkalo@intel.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel ipu mmu driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-mmu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-mmu.h
@@ -0,0 +1,76 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2021 Intel Corporation */
+
+#ifndef IPU_MMU_H
+#define IPU_MMU_H
+
+#include <linux/dma-mapping.h>
+
+#include "ipu.h"
+#include "ipu-pdata.h"
+
+#define ISYS_MMID 1
+#define PSYS_MMID 0
+
+/*
+ * @pgtbl: virtual address of the l1 page table (one page)
+ */
+struct ipu_mmu_info {
+	struct device *dev;
+
+	u32 __iomem *l1_pt;
+	u32 l1_pt_dma;
+	u32 **l2_pts;
+
+	u32 *dummy_l2_pt;
+	u32 dummy_l2_pteval;
+	void *dummy_page;
+	u32 dummy_page_pteval;
+
+	dma_addr_t aperture_start;
+	dma_addr_t aperture_end;
+	unsigned long pgsize_bitmap;
+
+	spinlock_t lock;	/* Serialize access to users */
+	struct ipu_dma_mapping *dmap;
+};
+
+/*
+ * @pgtbl: physical address of the l1 page table
+ */
+struct ipu_mmu {
+	struct list_head node;
+
+	struct ipu_mmu_hw *mmu_hw;
+	unsigned int nr_mmus;
+	int mmid;
+
+	phys_addr_t pgtbl;
+	struct device *dev;
+
+	struct ipu_dma_mapping *dmap;
+	struct list_head vma_list;
+
+	struct page *trash_page;
+	dma_addr_t pci_trash_page; /* IOVA from PCI DMA services (parent) */
+	dma_addr_t iova_trash_page; /* IOVA for IPU child nodes to use */
+
+	bool ready;
+	spinlock_t ready_lock;	/* Serialize access to bool ready */
+
+	void (*tlb_invalidate)(struct ipu_mmu *mmu);
+};
+
+struct ipu_mmu *ipu_mmu_init(struct device *dev,
+			     void __iomem *base, int mmid,
+			     const struct ipu_hw_variants *hw);
+void ipu_mmu_cleanup(struct ipu_mmu *mmu);
+int ipu_mmu_hw_init(struct ipu_mmu *mmu);
+int ipu_mmu_hw_cleanup(struct ipu_mmu *mmu);
+int ipu_mmu_map(struct ipu_mmu_info *mmu_info, unsigned long iova,
+		phys_addr_t paddr, size_t size);
+size_t ipu_mmu_unmap(struct ipu_mmu_info *mmu_info, unsigned long iova,
+		     size_t size);
+phys_addr_t ipu_mmu_iova_to_phys(struct ipu_mmu_info *mmu_info,
+				 dma_addr_t iova);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-pdata.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-pdata.h
@@ -0,0 +1,242 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2021 Intel Corporation */
+
+#ifndef IPU_PDATA_H
+#define IPU_PDATA_H
+
+#define IPU_MMU_NAME IPU_NAME "-mmu"
+#define IPU_ISYS_CSI2_NAME IPU_NAME "-csi2"
+#define IPU_ISYS_NAME IPU_NAME "-isys"
+#define IPU_PSYS_NAME IPU_NAME "-psys"
+#define IPU_BUTTRESS_NAME IPU_NAME "-buttress"
+
+#define IPU_MMU_MAX_DEVICES		4
+#define IPU_MMU_ADDRESS_BITS		32
+/* The firmware is accessible within the first 2 GiB only in non-secure mode. */
+#define IPU_MMU_ADDRESS_BITS_NON_SECURE	31
+
+#define IPU_MMU_MAX_TLB_L1_STREAMS	32
+#define IPU_MMU_MAX_TLB_L2_STREAMS	32
+#define IPU_MAX_LI_BLOCK_ADDR		128
+#define IPU_MAX_L2_BLOCK_ADDR		64
+
+#define IPU_ISYS_MAX_CSI2_LEGACY_PORTS	4
+#define IPU_ISYS_MAX_CSI2_COMBO_PORTS	2
+
+#define IPU_MAX_FRAME_COUNTER	0xff
+
+/*
+ * To maximize the IOSF utlization, IPU need to send requests in bursts.
+ * At the DMA interface with the buttress, there are CDC FIFOs with burst
+ * collection capability. CDC FIFO burst collectors have a configurable
+ * threshold and is configured based on the outcome of performance measurements.
+ *
+ * isys has 3 ports with IOSF interface for VC0, VC1 and VC2
+ * psys has 4 ports with IOSF interface for VC0, VC1w, VC1r and VC2
+ *
+ * Threshold values are pre-defined and are arrived at after performance
+ * evaluations on a type of IPU
+ */
+#define IPU_MAX_VC_IOSF_PORTS		4
+
+/*
+ * IPU must configure correct arbitration mechanism related to the IOSF VC
+ * requests. There are two options per VC0 and VC1 - > 0 means rearbitrate on
+ * stall and 1 means stall until the request is completed.
+ */
+#define IPU_BTRS_ARB_MODE_TYPE_REARB	0
+#define IPU_BTRS_ARB_MODE_TYPE_STALL	1
+
+/* Currently chosen arbitration mechanism for VC0 */
+#define IPU_BTRS_ARB_STALL_MODE_VC0	\
+			IPU_BTRS_ARB_MODE_TYPE_REARB
+
+/* Currently chosen arbitration mechanism for VC1 */
+#define IPU_BTRS_ARB_STALL_MODE_VC1	\
+			IPU_BTRS_ARB_MODE_TYPE_REARB
+
+struct ipu_isys_subdev_pdata;
+
+/*
+ * MMU Invalidation HW bug workaround by ZLW mechanism
+ *
+ * Old IPU MMUV2 has a bug in the invalidation mechanism which might result in
+ * wrong translation or replication of the translation. This will cause data
+ * corruption. So we cannot directly use the MMU V2 invalidation registers
+ * to invalidate the MMU. Instead, whenever an invalidate is called, we need to
+ * clear the TLB by evicting all the valid translations by filling it with trash
+ * buffer (which is guaranteed not to be used by any other processes). ZLW is
+ * used to fill the L1 and L2 caches with the trash buffer translations. ZLW
+ * or Zero length write, is pre-fetch mechanism to pre-fetch the pages in
+ * advance to the L1 and L2 caches without triggering any memory operations.
+ *
+ * In MMU V2, L1 -> 16 streams and 64 blocks, maximum 16 blocks per stream
+ * One L1 block has 16 entries, hence points to 16 * 4K pages
+ * L2 -> 16 streams and 32 blocks. 2 blocks per streams
+ * One L2 block maps to 1024 L1 entries, hence points to 4MB address range
+ * 2 blocks per L2 stream means, 1 stream points to 8MB range
+ *
+ * As we need to clear the caches and 8MB being the biggest cache size, we need
+ * to have trash buffer which points to 8MB address range. As these trash
+ * buffers are not used for any memory transactions, we need only the least
+ * amount of physical memory. So we reserve 8MB IOVA address range but only
+ * one page is reserved from physical memory. Each of this 8MB IOVA address
+ * range is then mapped to the same physical memory page.
+ */
+/* One L2 entry maps 1024 L1 entries and one L1 entry per page */
+#define IPU_MMUV2_L2_RANGE		(1024 * PAGE_SIZE)
+/* Max L2 blocks per stream */
+#define IPU_MMUV2_MAX_L2_BLOCKS		2
+/* Max L1 blocks per stream */
+#define IPU_MMUV2_MAX_L1_BLOCKS		16
+#define IPU_MMUV2_TRASH_RANGE		(IPU_MMUV2_L2_RANGE * \
+						 IPU_MMUV2_MAX_L2_BLOCKS)
+/* Entries per L1 block */
+#define MMUV2_ENTRIES_PER_L1_BLOCK		16
+#define MMUV2_TRASH_L1_BLOCK_OFFSET		(MMUV2_ENTRIES_PER_L1_BLOCK * \
+						 PAGE_SIZE)
+#define MMUV2_TRASH_L2_BLOCK_OFFSET		IPU_MMUV2_L2_RANGE
+
+/*
+ * In some of the IPU MMUs, there is provision to configure L1 and L2 page
+ * table caches. Both these L1 and L2 caches are divided into multiple sections
+ * called streams. There is maximum 16 streams for both caches. Each of these
+ * sections are subdivided into multiple blocks. When nr_l1streams = 0 and
+ * nr_l2streams = 0, means the MMU is of type MMU_V1 and do not support
+ * L1/L2 page table caches.
+ *
+ * L1 stream per block sizes are configurable and varies per usecase.
+ * L2 has constant block sizes - 2 blocks per stream.
+ *
+ * MMU1 support pre-fetching of the pages to have less cache lookup misses. To
+ * enable the pre-fetching, MMU1 AT (Address Translator) device registers
+ * need to be configured.
+ *
+ * There are four types of memory accesses which requires ZLW configuration.
+ * ZLW(Zero Length Write) is a mechanism to enable VT-d pre-fetching on IOMMU.
+ *
+ * 1. Sequential Access or 1D mode
+ *	Set ZLW_EN -> 1
+ *	set ZLW_PAGE_CROSS_1D -> 1
+ *	Set ZLW_N to "N" pages so that ZLW will be inserte N pages ahead where
+ *		  N is pre-defined and hardcoded in the platform data
+ *	Set ZLW_2D -> 0
+ *
+ * 2. ZLW 2D mode
+ *	Set ZLW_EN -> 1
+ *	set ZLW_PAGE_CROSS_1D -> 1,
+ *	Set ZLW_N -> 0
+ *	Set ZLW_2D -> 1
+ *
+ * 3. ZLW Enable (no 1D or 2D mode)
+ *	Set ZLW_EN -> 1
+ *	set ZLW_PAGE_CROSS_1D -> 0,
+ *	Set ZLW_N -> 0
+ *	Set ZLW_2D -> 0
+ *
+ * 4. ZLW disable
+ *	Set ZLW_EN -> 0
+ *	set ZLW_PAGE_CROSS_1D -> 0,
+ *	Set ZLW_N -> 0
+ *	Set ZLW_2D -> 0
+ *
+ * To configure the ZLW for the above memory access, four registers are
+ * available. Hence to track these four settings, we have the following entries
+ * in the struct ipu_mmu_hw. Each of these entries are per stream and
+ * available only for the L1 streams.
+ *
+ * a. l1_zlw_en -> To track zlw enabled per stream (ZLW_EN)
+ * b. l1_zlw_1d_mode -> Track 1D mode per stream. ZLW inserted at page boundary
+ * c. l1_ins_zlw_ahead_pages -> to track how advance the ZLW need to be inserted
+ *			Insert ZLW request N pages ahead address.
+ * d. l1_zlw_2d_mode -> To track 2D mode per stream (ZLW_2D)
+ *
+ *
+ * Currently L1/L2 streams, blocks, AT ZLW configurations etc. are pre-defined
+ * as per the usecase specific calculations. Any change to this pre-defined
+ * table has to happen in sync with IPU FW.
+ */
+struct ipu_mmu_hw {
+	union {
+		unsigned long offset;
+		void __iomem *base;
+	};
+	unsigned int info_bits;
+	u8 nr_l1streams;
+	/*
+	 * L1 has variable blocks per stream - total of 64 blocks and maximum of
+	 * 16 blocks per stream. Configurable by using the block start address
+	 * per stream. Block start address is calculated from the block size
+	 */
+	u8 l1_block_sz[IPU_MMU_MAX_TLB_L1_STREAMS];
+	/* Is ZLW is enabled in each stream */
+	bool l1_zlw_en[IPU_MMU_MAX_TLB_L1_STREAMS];
+	bool l1_zlw_1d_mode[IPU_MMU_MAX_TLB_L1_STREAMS];
+	u8 l1_ins_zlw_ahead_pages[IPU_MMU_MAX_TLB_L1_STREAMS];
+	bool l1_zlw_2d_mode[IPU_MMU_MAX_TLB_L1_STREAMS];
+
+	u32 l1_stream_id_reg_offset;
+	u32 l2_stream_id_reg_offset;
+
+	u8 nr_l2streams;
+	/*
+	 * L2 has fixed 2 blocks per stream. Block address is calculated
+	 * from the block size
+	 */
+	u8 l2_block_sz[IPU_MMU_MAX_TLB_L2_STREAMS];
+	/* flag to track if WA is needed for successive invalidate HW bug */
+	bool insert_read_before_invalidate;
+};
+
+struct ipu_mmu_pdata {
+	unsigned int nr_mmus;
+	struct ipu_mmu_hw mmu_hw[IPU_MMU_MAX_DEVICES];
+	int mmid;
+};
+
+struct ipu_isys_csi2_pdata {
+	void __iomem *base;
+};
+
+#define IPU_EV_AUTO 0xff
+
+struct ipu_isys_internal_csi2_pdata {
+	unsigned int nports;
+	unsigned int *offsets;
+};
+
+/*
+ * One place to handle all the IPU HW variations
+ */
+struct ipu_hw_variants {
+	unsigned long offset;
+	unsigned int nr_mmus;
+	struct ipu_mmu_hw mmu_hw[IPU_MMU_MAX_DEVICES];
+	u8 cdc_fifos;
+	u8 cdc_fifo_threshold[IPU_MAX_VC_IOSF_PORTS];
+	u32 dmem_offset;
+	u32 spc_offset;	/* SPC offset from psys base */
+};
+
+struct ipu_isys_internal_pdata {
+	struct ipu_isys_internal_csi2_pdata csi2;
+	struct ipu_hw_variants hw_variant;
+	u32 num_parallel_streams;
+	u32 isys_dma_overshoot;
+};
+
+struct ipu_isys_pdata {
+	void __iomem *base;
+	const struct ipu_isys_internal_pdata *ipdata;
+};
+
+struct ipu_psys_internal_pdata {
+	struct ipu_hw_variants hw_variant;
+};
+
+struct ipu_psys_pdata {
+	void __iomem *base;
+	const struct ipu_psys_internal_pdata *ipdata;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-psys-compat32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-psys-compat32.c
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/compat.h>
+#include <linux/errno.h>
+#include <linux/uaccess.h>
+
+#include <uapi/linux/ipu-psys.h>
+
+#include "ipu-psys.h"
+
+static long native_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	long ret = -ENOTTY;
+
+	if (file->f_op->unlocked_ioctl)
+		ret = file->f_op->unlocked_ioctl(file, cmd, arg);
+
+	return ret;
+}
+
+struct ipu_psys_buffer32 {
+	u64 len;
+	union {
+		int fd;
+		compat_uptr_t userptr;
+		u64 reserved;
+	} base;
+	u32 data_offset;
+	u32 bytes_used;
+	u32 flags;
+	u32 reserved[2];
+} __packed;
+
+struct ipu_psys_command32 {
+	u64 issue_id;
+	u64 user_token;
+	u32 priority;
+	compat_uptr_t pg_manifest;
+	compat_uptr_t buffers;
+	int pg;
+	u32 pg_manifest_size;
+	u32 bufcount;
+	u32 min_psys_freq;
+	u32 frame_counter;
+	u32 reserved[2];
+} __packed;
+
+struct ipu_psys_manifest32 {
+	u32 index;
+	u32 size;
+	compat_uptr_t manifest;
+	u32 reserved[5];
+} __packed;
+
+static int
+get_ipu_psys_command32(struct ipu_psys_command *kp,
+		       struct ipu_psys_command32 __user *up)
+{
+	compat_uptr_t pgm, bufs;
+	bool access_ok;
+
+	access_ok = access_ok(up, sizeof(struct ipu_psys_command32));
+	if (!access_ok || get_user(kp->issue_id, &up->issue_id) ||
+	    get_user(kp->user_token, &up->user_token) ||
+	    get_user(kp->priority, &up->priority) ||
+	    get_user(pgm, &up->pg_manifest) ||
+	    get_user(bufs, &up->buffers) ||
+	    get_user(kp->pg, &up->pg) ||
+	    get_user(kp->pg_manifest_size, &up->pg_manifest_size) ||
+	    get_user(kp->bufcount, &up->bufcount) ||
+	    get_user(kp->min_psys_freq, &up->min_psys_freq) ||
+	    get_user(kp->frame_counter, &up->frame_counter)
+	    )
+		return -EFAULT;
+
+	kp->pg_manifest = compat_ptr(pgm);
+	kp->buffers = compat_ptr(bufs);
+
+	return 0;
+}
+
+static int
+get_ipu_psys_buffer32(struct ipu_psys_buffer *kp,
+		      struct ipu_psys_buffer32 __user *up)
+{
+	compat_uptr_t ptr;
+	bool access_ok;
+
+	access_ok = access_ok(up, sizeof(struct ipu_psys_buffer32));
+	if (!access_ok || get_user(kp->len, &up->len) ||
+	    get_user(ptr, &up->base.userptr) ||
+	    get_user(kp->data_offset, &up->data_offset) ||
+	    get_user(kp->bytes_used, &up->bytes_used) ||
+	    get_user(kp->flags, &up->flags))
+		return -EFAULT;
+
+	kp->base.userptr = compat_ptr(ptr);
+
+	return 0;
+}
+
+static int
+put_ipu_psys_buffer32(struct ipu_psys_buffer *kp,
+		      struct ipu_psys_buffer32 __user *up)
+{
+	bool access_ok;
+
+	access_ok = access_ok(up, sizeof(struct ipu_psys_buffer32));
+	if (!access_ok || put_user(kp->len, &up->len) ||
+	    put_user(kp->base.fd, &up->base.fd) ||
+	    put_user(kp->data_offset, &up->data_offset) ||
+	    put_user(kp->bytes_used, &up->bytes_used) ||
+	    put_user(kp->flags, &up->flags))
+		return -EFAULT;
+
+	return 0;
+}
+
+static int
+get_ipu_psys_manifest32(struct ipu_psys_manifest *kp,
+			struct ipu_psys_manifest32 __user *up)
+{
+	compat_uptr_t ptr;
+	bool access_ok;
+
+	access_ok = access_ok(up, sizeof(struct ipu_psys_manifest32));
+	if (!access_ok || get_user(kp->index, &up->index) ||
+	    get_user(kp->size, &up->size) || get_user(ptr, &up->manifest))
+		return -EFAULT;
+
+	kp->manifest = compat_ptr(ptr);
+
+	return 0;
+}
+
+static int
+put_ipu_psys_manifest32(struct ipu_psys_manifest *kp,
+			struct ipu_psys_manifest32 __user *up)
+{
+	compat_uptr_t ptr = (u32)((unsigned long)kp->manifest);
+	bool access_ok;
+
+	access_ok = access_ok(up, sizeof(struct ipu_psys_manifest32));
+	if (!access_ok || put_user(kp->index, &up->index) ||
+	    put_user(kp->size, &up->size) || put_user(ptr, &up->manifest))
+		return -EFAULT;
+
+	return 0;
+}
+
+#define IPU_IOC_GETBUF32 _IOWR('A', 4, struct ipu_psys_buffer32)
+#define IPU_IOC_PUTBUF32 _IOWR('A', 5, struct ipu_psys_buffer32)
+#define IPU_IOC_QCMD32 _IOWR('A', 6, struct ipu_psys_command32)
+#define IPU_IOC_CMD_CANCEL32 _IOWR('A', 8, struct ipu_psys_command32)
+#define IPU_IOC_GET_MANIFEST32 _IOWR('A', 9, struct ipu_psys_manifest32)
+
+long ipu_psys_compat_ioctl32(struct file *file, unsigned int cmd,
+			     unsigned long arg)
+{
+	union {
+		struct ipu_psys_buffer buf;
+		struct ipu_psys_command cmd;
+		struct ipu_psys_event ev;
+		struct ipu_psys_manifest m;
+	} karg;
+	int compatible_arg = 1;
+	int err = 0;
+	void __user *up = compat_ptr(arg);
+
+	switch (cmd) {
+	case IPU_IOC_GETBUF32:
+		cmd = IPU_IOC_GETBUF;
+		break;
+	case IPU_IOC_PUTBUF32:
+		cmd = IPU_IOC_PUTBUF;
+		break;
+	case IPU_IOC_QCMD32:
+		cmd = IPU_IOC_QCMD;
+		break;
+	case IPU_IOC_GET_MANIFEST32:
+		cmd = IPU_IOC_GET_MANIFEST;
+		break;
+	}
+
+	switch (cmd) {
+	case IPU_IOC_GETBUF:
+	case IPU_IOC_PUTBUF:
+		err = get_ipu_psys_buffer32(&karg.buf, up);
+		compatible_arg = 0;
+		break;
+	case IPU_IOC_QCMD:
+		err = get_ipu_psys_command32(&karg.cmd, up);
+		compatible_arg = 0;
+		break;
+	case IPU_IOC_GET_MANIFEST:
+		err = get_ipu_psys_manifest32(&karg.m, up);
+		compatible_arg = 0;
+		break;
+	}
+	if (err)
+		return err;
+
+	if (compatible_arg) {
+		err = native_ioctl(file, cmd, (unsigned long)up);
+	} else {
+		mm_segment_t old_fs = force_uaccess_begin();
+
+		err = native_ioctl(file, cmd, (unsigned long)&karg);
+		force_uaccess_end(old_fs);
+	}
+
+	if (err)
+		return err;
+
+	switch (cmd) {
+	case IPU_IOC_GETBUF:
+		err = put_ipu_psys_buffer32(&karg.buf, up);
+		break;
+	case IPU_IOC_GET_MANIFEST:
+		err = put_ipu_psys_manifest32(&karg.m, up);
+		break;
+	}
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-psys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-psys.c
@@ -0,0 +1,1619 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/firmware.h>
+#include <linux/fs.h>
+#include <linux/highmem.h>
+#include <linux/init_task.h>
+#include <linux/kthread.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/version.h>
+#include <linux/poll.h>
+#include <uapi/linux/sched/types.h>
+#include <linux/uaccess.h>
+#include <linux/vmalloc.h>
+#include <linux/dma-mapping.h>
+
+#include <uapi/linux/ipu-psys.h>
+
+#include "ipu.h"
+#include "ipu-mmu.h"
+#include "ipu-bus.h"
+#include "ipu-platform.h"
+#include "ipu-buttress.h"
+#include "ipu-cpd.h"
+#include "ipu-fw-psys.h"
+#include "ipu-psys.h"
+#include "ipu-platform-psys.h"
+#include "ipu-platform-regs.h"
+#include "ipu-fw-com.h"
+
+static bool async_fw_init;
+module_param(async_fw_init, bool, 0664);
+MODULE_PARM_DESC(async_fw_init, "Enable asynchronous firmware initialization");
+
+#define IPU_PSYS_NUM_DEVICES		4
+#define IPU_PSYS_AUTOSUSPEND_DELAY	2000
+
+#ifdef CONFIG_PM
+static int psys_runtime_pm_resume(struct device *dev);
+static int psys_runtime_pm_suspend(struct device *dev);
+#else
+#define pm_runtime_dont_use_autosuspend(d)
+#define pm_runtime_use_autosuspend(d)
+#define pm_runtime_set_autosuspend_delay(d, f)	0
+#define pm_runtime_get_sync(d)			0
+#define pm_runtime_put(d)			0
+#define pm_runtime_put_sync(d)			0
+#define pm_runtime_put_noidle(d)		0
+#define pm_runtime_put_autosuspend(d)		0
+#endif
+
+static dev_t ipu_psys_dev_t;
+static DECLARE_BITMAP(ipu_psys_devices, IPU_PSYS_NUM_DEVICES);
+static DEFINE_MUTEX(ipu_psys_mutex);
+
+static struct fw_init_task {
+	struct delayed_work work;
+	struct ipu_psys *psys;
+} fw_init_task;
+
+static void ipu_psys_remove(struct ipu_bus_device *adev);
+
+static struct bus_type ipu_psys_bus = {
+	.name = IPU_PSYS_NAME,
+};
+
+struct ipu_psys_pg *__get_pg_buf(struct ipu_psys *psys, size_t pg_size)
+{
+	struct ipu_psys_pg *kpg;
+	unsigned long flags;
+
+	spin_lock_irqsave(&psys->pgs_lock, flags);
+	list_for_each_entry(kpg, &psys->pgs, list) {
+		if (!kpg->pg_size && kpg->size >= pg_size) {
+			kpg->pg_size = pg_size;
+			spin_unlock_irqrestore(&psys->pgs_lock, flags);
+			return kpg;
+		}
+	}
+	spin_unlock_irqrestore(&psys->pgs_lock, flags);
+	/* no big enough buffer available, allocate new one */
+	kpg = kzalloc(sizeof(*kpg), GFP_KERNEL);
+	if (!kpg)
+		return NULL;
+
+	kpg->pg = dma_alloc_attrs(&psys->adev->dev, pg_size,
+				  &kpg->pg_dma_addr, GFP_KERNEL, 0);
+	if (!kpg->pg) {
+		kfree(kpg);
+		return NULL;
+	}
+
+	kpg->pg_size = pg_size;
+	kpg->size = pg_size;
+	spin_lock_irqsave(&psys->pgs_lock, flags);
+	list_add(&kpg->list, &psys->pgs);
+	spin_unlock_irqrestore(&psys->pgs_lock, flags);
+
+	return kpg;
+}
+
+static int ipu_psys_unmapbuf_locked(int fd, struct ipu_psys_fh *fh,
+				    struct ipu_psys_kbuffer *kbuf);
+struct ipu_psys_kbuffer *ipu_psys_lookup_kbuffer(struct ipu_psys_fh *fh, int fd)
+{
+	struct ipu_psys_kbuffer *kbuf;
+
+	list_for_each_entry(kbuf, &fh->bufmap, list) {
+		if (kbuf->fd == fd)
+			return kbuf;
+	}
+
+	return NULL;
+}
+
+struct ipu_psys_kbuffer *
+ipu_psys_lookup_kbuffer_by_kaddr(struct ipu_psys_fh *fh, void *kaddr)
+{
+	struct ipu_psys_kbuffer *kbuffer;
+
+	list_for_each_entry(kbuffer, &fh->bufmap, list) {
+		if (kbuffer->kaddr == kaddr)
+			return kbuffer;
+	}
+
+	return NULL;
+}
+
+static int ipu_psys_get_userpages(struct ipu_dma_buf_attach *attach)
+{
+	struct vm_area_struct *vma;
+	unsigned long start, end;
+	int npages, array_size;
+	struct page **pages;
+	struct sg_table *sgt;
+	int nr = 0;
+	int ret = -ENOMEM;
+
+	start = (unsigned long)attach->userptr;
+	end = PAGE_ALIGN(start + attach->len);
+	npages = (end - (start & PAGE_MASK)) >> PAGE_SHIFT;
+	array_size = npages * sizeof(struct page *);
+
+	sgt = kzalloc(sizeof(*sgt), GFP_KERNEL);
+	if (!sgt)
+		return -ENOMEM;
+
+	if (attach->npages != 0) {
+		pages = attach->pages;
+		npages = attach->npages;
+		attach->vma_is_io = 1;
+		goto skip_pages;
+	}
+
+	pages = kvzalloc(array_size, GFP_KERNEL);
+	if (!pages)
+		goto free_sgt;
+
+	mmap_read_lock(current->mm);
+	vma = find_vma(current->mm, start);
+	if (!vma) {
+		ret = -EFAULT;
+		goto error_up_read;
+	}
+
+	/*
+	 * For buffers from Gralloc, VM_PFNMAP is expected,
+	 * but VM_IO is set. Possibly bug in Gralloc.
+	 */
+	attach->vma_is_io = vma->vm_flags & (VM_IO | VM_PFNMAP);
+
+	if (attach->vma_is_io) {
+		unsigned long io_start = start;
+
+		if (vma->vm_end < start + attach->len) {
+			dev_err(attach->dev,
+				"vma at %lu is too small for %llu bytes\n",
+				start, attach->len);
+			ret = -EFAULT;
+			goto error_up_read;
+		}
+
+		for (nr = 0; nr < npages; nr++, io_start += PAGE_SIZE) {
+			unsigned long pfn;
+
+			ret = follow_pfn(vma, io_start, &pfn);
+			if (ret)
+				goto error_up_read;
+			pages[nr] = pfn_to_page(pfn);
+		}
+	} else {
+		nr = get_user_pages(start & PAGE_MASK, npages,
+				    FOLL_WRITE,
+				    pages, NULL);
+		if (nr < npages)
+			goto error_up_read;
+	}
+	mmap_read_unlock(current->mm);
+
+	attach->pages = pages;
+	attach->npages = npages;
+
+skip_pages:
+	ret = sg_alloc_table_from_pages(sgt, pages, npages,
+					start & ~PAGE_MASK, attach->len,
+					GFP_KERNEL);
+	if (ret < 0)
+		goto error;
+
+	attach->sgt = sgt;
+
+	return 0;
+
+error_up_read:
+	mmap_read_unlock(current->mm);
+error:
+	if (!attach->vma_is_io)
+		while (nr > 0)
+			put_page(pages[--nr]);
+
+	if (array_size <= PAGE_SIZE)
+		kfree(pages);
+	else
+		vfree(pages);
+free_sgt:
+	kfree(sgt);
+
+	dev_err(attach->dev, "failed to get userpages:%d\n", ret);
+
+	return ret;
+}
+
+static void ipu_psys_put_userpages(struct ipu_dma_buf_attach *attach)
+{
+	if (!attach || !attach->userptr || !attach->sgt)
+		return;
+
+	if (!attach->vma_is_io) {
+		int i = attach->npages;
+
+		while (--i >= 0) {
+			set_page_dirty_lock(attach->pages[i]);
+			put_page(attach->pages[i]);
+		}
+	}
+
+	kvfree(attach->pages);
+
+	sg_free_table(attach->sgt);
+	kfree(attach->sgt);
+	attach->sgt = NULL;
+}
+
+static int ipu_dma_buf_attach(struct dma_buf *dbuf,
+			      struct dma_buf_attachment *attach)
+{
+	struct ipu_psys_kbuffer *kbuf = dbuf->priv;
+	struct ipu_dma_buf_attach *ipu_attach;
+
+	ipu_attach = kzalloc(sizeof(*ipu_attach), GFP_KERNEL);
+	if (!ipu_attach)
+		return -ENOMEM;
+
+	ipu_attach->len = kbuf->len;
+	ipu_attach->userptr = kbuf->userptr;
+
+	attach->priv = ipu_attach;
+	return 0;
+}
+
+static void ipu_dma_buf_detach(struct dma_buf *dbuf,
+			       struct dma_buf_attachment *attach)
+{
+	struct ipu_dma_buf_attach *ipu_attach = attach->priv;
+
+	kfree(ipu_attach);
+	attach->priv = NULL;
+}
+
+static struct sg_table *ipu_dma_buf_map(struct dma_buf_attachment *attach,
+					enum dma_data_direction dir)
+{
+	struct ipu_dma_buf_attach *ipu_attach = attach->priv;
+	unsigned long attrs;
+	int ret;
+
+	ret = ipu_psys_get_userpages(ipu_attach);
+	if (ret)
+		return NULL;
+
+	attrs = DMA_ATTR_SKIP_CPU_SYNC;
+	ret = dma_map_sg_attrs(attach->dev, ipu_attach->sgt->sgl,
+			       ipu_attach->sgt->orig_nents, dir, attrs);
+	if (ret < ipu_attach->sgt->orig_nents) {
+		ipu_psys_put_userpages(ipu_attach);
+		dev_dbg(attach->dev, "buf map failed\n");
+
+		return ERR_PTR(-EIO);
+	}
+
+	/*
+	 * Initial cache flush to avoid writing dirty pages for buffers which
+	 * are later marked as IPU_BUFFER_FLAG_NO_FLUSH.
+	 */
+	dma_sync_sg_for_device(attach->dev, ipu_attach->sgt->sgl,
+			       ipu_attach->sgt->orig_nents, DMA_BIDIRECTIONAL);
+
+	return ipu_attach->sgt;
+}
+
+static void ipu_dma_buf_unmap(struct dma_buf_attachment *attach,
+			      struct sg_table *sg, enum dma_data_direction dir)
+{
+	struct ipu_dma_buf_attach *ipu_attach = attach->priv;
+
+	dma_unmap_sg(attach->dev, sg->sgl, sg->orig_nents, dir);
+	ipu_psys_put_userpages(ipu_attach);
+}
+
+static int ipu_dma_buf_mmap(struct dma_buf *dbuf, struct vm_area_struct *vma)
+{
+	return -ENOTTY;
+}
+
+static void ipu_dma_buf_release(struct dma_buf *buf)
+{
+	struct ipu_psys_kbuffer *kbuf = buf->priv;
+
+	if (!kbuf)
+		return;
+
+	if (kbuf->db_attach) {
+		dev_dbg(kbuf->db_attach->dev,
+			"releasing buffer %d\n", kbuf->fd);
+		ipu_psys_put_userpages(kbuf->db_attach->priv);
+	}
+	kfree(kbuf);
+}
+
+static int ipu_dma_buf_begin_cpu_access(struct dma_buf *dma_buf,
+					enum dma_data_direction dir)
+{
+	return -ENOTTY;
+}
+
+static int ipu_dma_buf_vmap(struct dma_buf *dmabuf, struct dma_buf_map *map)
+{
+	struct dma_buf_attachment *attach;
+	struct ipu_dma_buf_attach *ipu_attach;
+
+	if (list_empty(&dmabuf->attachments))
+		return -EINVAL;
+
+	attach = list_last_entry(&dmabuf->attachments,
+				 struct dma_buf_attachment, node);
+	ipu_attach = attach->priv;
+
+	if (!ipu_attach || !ipu_attach->pages || !ipu_attach->npages)
+		return -EINVAL;
+
+	map->vaddr = vm_map_ram(ipu_attach->pages, ipu_attach->npages, 0);
+	map->is_iomem = false;
+	if (!map->vaddr)
+		return -EINVAL;
+
+	return 0;
+}
+
+static void ipu_dma_buf_vunmap(struct dma_buf *dmabuf, struct dma_buf_map *map)
+{
+	struct dma_buf_attachment *attach;
+	struct ipu_dma_buf_attach *ipu_attach;
+
+	if (WARN_ON(list_empty(&dmabuf->attachments)))
+		return;
+
+	attach = list_last_entry(&dmabuf->attachments,
+				 struct dma_buf_attachment, node);
+	ipu_attach = attach->priv;
+
+	if (WARN_ON(!ipu_attach || !ipu_attach->pages || !ipu_attach->npages))
+		return;
+
+	vm_unmap_ram(map->vaddr, ipu_attach->npages);
+}
+
+struct dma_buf_ops ipu_dma_buf_ops = {
+	.attach = ipu_dma_buf_attach,
+	.detach = ipu_dma_buf_detach,
+	.map_dma_buf = ipu_dma_buf_map,
+	.unmap_dma_buf = ipu_dma_buf_unmap,
+	.release = ipu_dma_buf_release,
+	.begin_cpu_access = ipu_dma_buf_begin_cpu_access,
+	.mmap = ipu_dma_buf_mmap,
+	.vmap = ipu_dma_buf_vmap,
+	.vunmap = ipu_dma_buf_vunmap,
+};
+
+static int ipu_psys_open(struct inode *inode, struct file *file)
+{
+	struct ipu_psys *psys = inode_to_ipu_psys(inode);
+	struct ipu_device *isp = psys->adev->isp;
+	struct ipu_psys_fh *fh;
+	int rval;
+
+	if (isp->flr_done)
+		return -EIO;
+
+	fh = kzalloc(sizeof(*fh), GFP_KERNEL);
+	if (!fh)
+		return -ENOMEM;
+
+	fh->psys = psys;
+
+	file->private_data = fh;
+
+	mutex_init(&fh->mutex);
+	INIT_LIST_HEAD(&fh->bufmap);
+	init_waitqueue_head(&fh->wait);
+
+	rval = ipu_psys_fh_init(fh);
+	if (rval)
+		goto open_failed;
+
+	mutex_lock(&psys->mutex);
+	list_add_tail(&fh->list, &psys->fhs);
+	mutex_unlock(&psys->mutex);
+
+	return 0;
+
+open_failed:
+	mutex_destroy(&fh->mutex);
+	kfree(fh);
+	return rval;
+}
+
+static inline void ipu_psys_kbuf_unmap(struct ipu_psys_kbuffer *kbuf)
+{
+	if (!kbuf)
+		return;
+
+	kbuf->valid = false;
+	if (kbuf->kaddr) {
+		struct dma_buf_map dmap;
+
+		dma_buf_map_set_vaddr(&dmap, kbuf->kaddr);
+		dma_buf_vunmap(kbuf->dbuf, &dmap);
+	}
+	if (kbuf->sgt)
+		dma_buf_unmap_attachment(kbuf->db_attach,
+					 kbuf->sgt,
+					 DMA_BIDIRECTIONAL);
+	if (kbuf->db_attach)
+		dma_buf_detach(kbuf->dbuf, kbuf->db_attach);
+	dma_buf_put(kbuf->dbuf);
+
+	kbuf->db_attach = NULL;
+	kbuf->dbuf = NULL;
+	kbuf->sgt = NULL;
+}
+
+static int ipu_psys_release(struct inode *inode, struct file *file)
+{
+	struct ipu_psys *psys = inode_to_ipu_psys(inode);
+	struct ipu_psys_fh *fh = file->private_data;
+	struct ipu_psys_kbuffer *kbuf, *kbuf0;
+	struct dma_buf_attachment *db_attach;
+
+	mutex_lock(&fh->mutex);
+	/* clean up buffers */
+	if (!list_empty(&fh->bufmap)) {
+		list_for_each_entry_safe(kbuf, kbuf0, &fh->bufmap, list) {
+			list_del(&kbuf->list);
+			db_attach = kbuf->db_attach;
+
+			/* Unmap and release buffers */
+			if (kbuf->dbuf && db_attach) {
+
+				ipu_psys_kbuf_unmap(kbuf);
+			} else {
+				if (db_attach)
+					ipu_psys_put_userpages(db_attach->priv);
+				kfree(kbuf);
+			}
+		}
+	}
+	mutex_unlock(&fh->mutex);
+
+	mutex_lock(&psys->mutex);
+	list_del(&fh->list);
+
+	mutex_unlock(&psys->mutex);
+	ipu_psys_fh_deinit(fh);
+
+	mutex_lock(&psys->mutex);
+	if (list_empty(&psys->fhs))
+		psys->power_gating = 0;
+	mutex_unlock(&psys->mutex);
+	mutex_destroy(&fh->mutex);
+	kfree(fh);
+
+	return 0;
+}
+
+static int ipu_psys_getbuf(struct ipu_psys_buffer *buf, struct ipu_psys_fh *fh)
+{
+	struct ipu_psys_kbuffer *kbuf;
+	struct ipu_psys *psys = fh->psys;
+
+	DEFINE_DMA_BUF_EXPORT_INFO(exp_info);
+	struct dma_buf *dbuf;
+	int ret;
+
+	if (!buf->base.userptr) {
+		dev_err(&psys->adev->dev, "Buffer allocation not supported\n");
+		return -EINVAL;
+	}
+
+	kbuf = kzalloc(sizeof(*kbuf), GFP_KERNEL);
+	if (!kbuf)
+		return -ENOMEM;
+
+	kbuf->len = buf->len;
+	kbuf->userptr = buf->base.userptr;
+	kbuf->flags = buf->flags;
+
+	exp_info.ops = &ipu_dma_buf_ops;
+	exp_info.size = kbuf->len;
+	exp_info.flags = O_RDWR;
+	exp_info.priv = kbuf;
+
+	dbuf = dma_buf_export(&exp_info);
+	if (IS_ERR(dbuf)) {
+		kfree(kbuf);
+		return PTR_ERR(dbuf);
+	}
+
+	ret = dma_buf_fd(dbuf, 0);
+	if (ret < 0) {
+		kfree(kbuf);
+		dma_buf_put(dbuf);
+		return ret;
+	}
+
+	kbuf->fd = ret;
+	buf->base.fd = ret;
+	kbuf->flags = buf->flags &= ~IPU_BUFFER_FLAG_USERPTR;
+	kbuf->flags = buf->flags |= IPU_BUFFER_FLAG_DMA_HANDLE;
+
+	mutex_lock(&fh->mutex);
+	list_add(&kbuf->list, &fh->bufmap);
+	mutex_unlock(&fh->mutex);
+
+	dev_dbg(&psys->adev->dev, "IOC_GETBUF: userptr %p size %llu to fd %d",
+		buf->base.userptr, buf->len, buf->base.fd);
+
+	return 0;
+}
+
+static int ipu_psys_putbuf(struct ipu_psys_buffer *buf, struct ipu_psys_fh *fh)
+{
+	return 0;
+}
+
+int ipu_psys_mapbuf_locked(int fd, struct ipu_psys_fh *fh,
+			   struct ipu_psys_kbuffer *kbuf)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct dma_buf *dbuf;
+	struct dma_buf_map dmap;
+	int ret;
+
+	dbuf = dma_buf_get(fd);
+	if (IS_ERR(dbuf))
+		return -EINVAL;
+
+	if (!kbuf) {
+		/* This fd isn't generated by ipu_psys_getbuf, it
+		 * is a new fd. Create a new kbuf item for this fd, and
+		 * add this kbuf to bufmap list.
+		 */
+		kbuf = kzalloc(sizeof(*kbuf), GFP_KERNEL);
+		if (!kbuf) {
+			ret = -ENOMEM;
+			goto mapbuf_fail;
+		}
+
+		list_add(&kbuf->list, &fh->bufmap);
+	}
+
+	/* fd valid and found, need remap */
+	if (kbuf->dbuf && (kbuf->dbuf != dbuf || kbuf->len != dbuf->size)) {
+		dev_dbg(&psys->adev->dev,
+			"dmabuf fd %d with kbuf %p changed, need remap.\n",
+			fd, kbuf);
+		ret = ipu_psys_unmapbuf_locked(fd, fh, kbuf);
+		if (ret)
+			goto mapbuf_fail;
+
+		kbuf = ipu_psys_lookup_kbuffer(fh, fd);
+		/* changed external dmabuf */
+		if (!kbuf) {
+			kbuf = kzalloc(sizeof(*kbuf), GFP_KERNEL);
+			if (!kbuf) {
+				ret = -ENOMEM;
+				goto mapbuf_fail;
+			}
+			list_add(&kbuf->list, &fh->bufmap);
+		}
+	}
+
+	if (kbuf->sgt) {
+		dev_dbg(&psys->adev->dev, "fd %d has been mapped!\n", fd);
+		dma_buf_put(dbuf);
+		goto mapbuf_end;
+	}
+
+	kbuf->dbuf = dbuf;
+
+	if (kbuf->len == 0)
+		kbuf->len = kbuf->dbuf->size;
+
+	kbuf->fd = fd;
+
+	kbuf->db_attach = dma_buf_attach(kbuf->dbuf, &psys->adev->dev);
+	if (IS_ERR(kbuf->db_attach)) {
+		ret = PTR_ERR(kbuf->db_attach);
+		dev_dbg(&psys->adev->dev, "dma buf attach failed\n");
+		goto kbuf_map_fail;
+	}
+
+	kbuf->sgt = dma_buf_map_attachment(kbuf->db_attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR_OR_NULL(kbuf->sgt)) {
+		ret = -EINVAL;
+		kbuf->sgt = NULL;
+		dev_dbg(&psys->adev->dev, "dma buf map attachment failed\n");
+		goto kbuf_map_fail;
+	}
+
+	kbuf->dma_addr = sg_dma_address(kbuf->sgt->sgl);
+
+	ret = dma_buf_vmap(kbuf->dbuf, &dmap);
+	if (ret) {
+		dev_dbg(&psys->adev->dev, "dma buf vmap failed\n");
+		goto kbuf_map_fail;
+	}
+	kbuf->kaddr = dmap.vaddr;
+
+	dev_dbg(&psys->adev->dev, "%s kbuf %p fd %d with len %llu mapped\n",
+		__func__, kbuf, fd, kbuf->len);
+mapbuf_end:
+
+	kbuf->valid = true;
+
+	return 0;
+
+kbuf_map_fail:
+	ipu_psys_kbuf_unmap(kbuf);
+
+	list_del(&kbuf->list);
+	if (!kbuf->userptr)
+		kfree(kbuf);
+	return ret;
+
+mapbuf_fail:
+	dma_buf_put(dbuf);
+
+	dev_err(&psys->adev->dev, "%s failed for fd %d\n", __func__, fd);
+	return ret;
+}
+
+static long ipu_psys_mapbuf(int fd, struct ipu_psys_fh *fh)
+{
+	long ret;
+	struct ipu_psys_kbuffer *kbuf;
+
+	mutex_lock(&fh->mutex);
+	kbuf = ipu_psys_lookup_kbuffer(fh, fd);
+	ret = ipu_psys_mapbuf_locked(fd, fh, kbuf);
+	mutex_unlock(&fh->mutex);
+
+	dev_dbg(&fh->psys->adev->dev, "IOC_MAPBUF ret %ld\n", ret);
+
+	return ret;
+}
+
+static int ipu_psys_unmapbuf_locked(int fd, struct ipu_psys_fh *fh,
+				    struct ipu_psys_kbuffer *kbuf)
+{
+	struct ipu_psys *psys = fh->psys;
+
+	if (!kbuf || fd != kbuf->fd) {
+		dev_err(&psys->adev->dev, "invalid kbuffer\n");
+		return -EINVAL;
+	}
+
+	/* From now on it is not safe to use this kbuffer */
+	ipu_psys_kbuf_unmap(kbuf);
+
+	list_del(&kbuf->list);
+
+	if (!kbuf->userptr)
+		kfree(kbuf);
+
+	dev_dbg(&psys->adev->dev, "%s fd %d unmapped\n", __func__, fd);
+
+	return 0;
+}
+
+static long ipu_psys_unmapbuf(int fd, struct ipu_psys_fh *fh)
+{
+	struct ipu_psys_kbuffer *kbuf;
+	long ret;
+
+	mutex_lock(&fh->mutex);
+	kbuf = ipu_psys_lookup_kbuffer(fh, fd);
+	if (!kbuf) {
+		dev_err(&fh->psys->adev->dev,
+			"buffer with fd %d not found\n", fd);
+		mutex_unlock(&fh->mutex);
+		return -EINVAL;
+	}
+	ret = ipu_psys_unmapbuf_locked(fd, fh, kbuf);
+	mutex_unlock(&fh->mutex);
+
+	dev_dbg(&fh->psys->adev->dev, "IOC_UNMAPBUF\n");
+
+	return ret;
+}
+
+static unsigned int ipu_psys_poll(struct file *file,
+				  struct poll_table_struct *wait)
+{
+	struct ipu_psys_fh *fh = file->private_data;
+	struct ipu_psys *psys = fh->psys;
+	unsigned int res = 0;
+
+	dev_dbg(&psys->adev->dev, "ipu psys poll\n");
+
+	poll_wait(file, &fh->wait, wait);
+
+	if (ipu_get_completed_kcmd(fh))
+		res = POLLIN;
+
+	dev_dbg(&psys->adev->dev, "ipu psys poll res %u\n", res);
+
+	return res;
+}
+
+static long ipu_get_manifest(struct ipu_psys_manifest *manifest,
+			     struct ipu_psys_fh *fh)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_device *isp = psys->adev->isp;
+	struct ipu_cpd_client_pkg_hdr *client_pkg;
+	u32 entries;
+	void *host_fw_data;
+	dma_addr_t dma_fw_data;
+	u32 client_pkg_offset;
+
+	host_fw_data = (void *)isp->cpd_fw->data;
+	dma_fw_data = sg_dma_address(psys->fw_sgt.sgl);
+
+	entries = ipu_cpd_pkg_dir_get_num_entries(psys->pkg_dir);
+	if (!manifest || manifest->index > entries - 1) {
+		dev_err(&psys->adev->dev, "invalid argument\n");
+		return -EINVAL;
+	}
+
+	if (!ipu_cpd_pkg_dir_get_size(psys->pkg_dir, manifest->index) ||
+	    ipu_cpd_pkg_dir_get_type(psys->pkg_dir, manifest->index) <
+	    IPU_CPD_PKG_DIR_CLIENT_PG_TYPE) {
+		dev_dbg(&psys->adev->dev, "invalid pkg dir entry\n");
+		return -ENOENT;
+	}
+
+	client_pkg_offset = ipu_cpd_pkg_dir_get_address(psys->pkg_dir,
+							manifest->index);
+	client_pkg_offset -= dma_fw_data;
+
+	client_pkg = host_fw_data + client_pkg_offset;
+	manifest->size = client_pkg->pg_manifest_size;
+
+	if (!manifest->manifest)
+		return 0;
+
+	if (copy_to_user(manifest->manifest,
+			 (uint8_t *)client_pkg + client_pkg->pg_manifest_offs,
+			 manifest->size)) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+static long ipu_psys_ioctl(struct file *file, unsigned int cmd,
+			   unsigned long arg)
+{
+	union {
+		struct ipu_psys_buffer buf;
+		struct ipu_psys_command cmd;
+		struct ipu_psys_event ev;
+		struct ipu_psys_capability caps;
+		struct ipu_psys_manifest m;
+	} karg;
+	struct ipu_psys_fh *fh = file->private_data;
+	long err = 0;
+	void __user *up = (void __user *)arg;
+	bool copy = (cmd != IPU_IOC_MAPBUF && cmd != IPU_IOC_UNMAPBUF);
+
+	if (copy) {
+		if (_IOC_SIZE(cmd) > sizeof(karg))
+			return -ENOTTY;
+
+		if (_IOC_DIR(cmd) & _IOC_WRITE) {
+			err = copy_from_user(&karg, up, _IOC_SIZE(cmd));
+			if (err)
+				return -EFAULT;
+		}
+	}
+
+	switch (cmd) {
+	case IPU_IOC_MAPBUF:
+		err = ipu_psys_mapbuf(arg, fh);
+		break;
+	case IPU_IOC_UNMAPBUF:
+		err = ipu_psys_unmapbuf(arg, fh);
+		break;
+	case IPU_IOC_QUERYCAP:
+		karg.caps = fh->psys->caps;
+		break;
+	case IPU_IOC_GETBUF:
+		err = ipu_psys_getbuf(&karg.buf, fh);
+		break;
+	case IPU_IOC_PUTBUF:
+		err = ipu_psys_putbuf(&karg.buf, fh);
+		break;
+	case IPU_IOC_QCMD:
+		err = ipu_psys_kcmd_new(&karg.cmd, fh);
+		break;
+	case IPU_IOC_DQEVENT:
+		err = ipu_ioctl_dqevent(&karg.ev, fh, file->f_flags);
+		break;
+	case IPU_IOC_GET_MANIFEST:
+		err = ipu_get_manifest(&karg.m, fh);
+		break;
+	default:
+		err = -ENOTTY;
+		break;
+	}
+
+	if (err)
+		return err;
+
+	if (copy && _IOC_DIR(cmd) & _IOC_READ)
+		if (copy_to_user(up, &karg, _IOC_SIZE(cmd)))
+			return -EFAULT;
+
+	return 0;
+}
+
+static const struct file_operations ipu_psys_fops = {
+	.open = ipu_psys_open,
+	.release = ipu_psys_release,
+	.unlocked_ioctl = ipu_psys_ioctl,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = ipu_psys_compat_ioctl32,
+#endif
+	.poll = ipu_psys_poll,
+	.owner = THIS_MODULE,
+};
+
+static void ipu_psys_dev_release(struct device *dev)
+{
+}
+
+#ifdef CONFIG_PM
+static int psys_runtime_pm_resume(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_psys *psys = ipu_bus_get_drvdata(adev);
+	unsigned long flags;
+	int retval;
+
+	if (!psys)
+		return 0;
+
+	/*
+	 * In runtime autosuspend mode, if the psys is in power on state, no
+	 * need to resume again.
+	 */
+	spin_lock_irqsave(&psys->ready_lock, flags);
+	if (psys->ready) {
+		spin_unlock_irqrestore(&psys->ready_lock, flags);
+		return 0;
+	}
+	spin_unlock_irqrestore(&psys->ready_lock, flags);
+
+	retval = ipu_mmu_hw_init(adev->mmu);
+	if (retval)
+		return retval;
+
+	if (async_fw_init && !psys->fwcom) {
+		dev_err(dev,
+			"%s: asynchronous firmware init not finished, skipping\n",
+			__func__);
+		return 0;
+	}
+
+	if (!ipu_buttress_auth_done(adev->isp)) {
+		dev_dbg(dev, "%s: not yet authenticated, skipping\n", __func__);
+		return 0;
+	}
+
+	ipu_psys_setup_hw(psys);
+
+	ipu_psys_subdomains_power(psys, 1);
+	ipu_trace_restore(&psys->adev->dev);
+
+	ipu_configure_spc(adev->isp,
+			  &psys->pdata->ipdata->hw_variant,
+			  IPU_CPD_PKG_DIR_PSYS_SERVER_IDX,
+			  psys->pdata->base, psys->pkg_dir,
+			  psys->pkg_dir_dma_addr);
+
+	retval = ipu_fw_psys_open(psys);
+	if (retval) {
+		dev_err(&psys->adev->dev, "Failed to open abi.\n");
+		return retval;
+	}
+
+	spin_lock_irqsave(&psys->ready_lock, flags);
+	psys->ready = 1;
+	spin_unlock_irqrestore(&psys->ready_lock, flags);
+
+	return 0;
+}
+
+static int psys_runtime_pm_suspend(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_psys *psys = ipu_bus_get_drvdata(adev);
+	unsigned long flags;
+	int rval;
+
+	if (!psys)
+		return 0;
+
+	if (!psys->ready)
+		return 0;
+
+	spin_lock_irqsave(&psys->ready_lock, flags);
+	psys->ready = 0;
+	spin_unlock_irqrestore(&psys->ready_lock, flags);
+
+	/*
+	 * We can trace failure but better to not return an error.
+	 * At suspend we are progressing towards psys power gated state.
+	 * Any hang / failure inside psys will be forgotten soon.
+	 */
+	rval = ipu_fw_psys_close(psys);
+	if (rval)
+		dev_err(dev, "Device close failure: %d\n", rval);
+
+	ipu_psys_subdomains_power(psys, 0);
+
+	ipu_mmu_hw_cleanup(adev->mmu);
+
+	return 0;
+}
+
+/* The following PM callbacks are needed to enable runtime PM in IPU PCI
+ * device resume, otherwise, runtime PM can't work in PCI resume from
+ * S3 state.
+ */
+static int psys_resume(struct device *dev)
+{
+	return 0;
+}
+
+static int psys_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static const struct dev_pm_ops psys_pm_ops = {
+	.runtime_suspend = psys_runtime_pm_suspend,
+	.runtime_resume = psys_runtime_pm_resume,
+	.suspend = psys_suspend,
+	.resume = psys_resume,
+};
+
+#define PSYS_PM_OPS (&psys_pm_ops)
+#else
+#define PSYS_PM_OPS NULL
+#endif
+
+static int cpd_fw_reload(struct ipu_device *isp)
+{
+	struct ipu_psys *psys = ipu_bus_get_drvdata(isp->psys);
+	int rval;
+
+	if (!isp->secure_mode) {
+		dev_warn(&isp->pdev->dev,
+			 "CPD firmware reload was only supported for secure mode.\n");
+		return -EINVAL;
+	}
+
+	if (isp->cpd_fw) {
+		ipu_cpd_free_pkg_dir(isp->psys, psys->pkg_dir,
+				     psys->pkg_dir_dma_addr,
+				     psys->pkg_dir_size);
+
+		ipu_buttress_unmap_fw_image(isp->psys, &psys->fw_sgt);
+		release_firmware(isp->cpd_fw);
+		isp->cpd_fw = NULL;
+		dev_info(&isp->pdev->dev, "Old FW removed\n");
+	}
+
+	rval = request_cpd_fw(&isp->cpd_fw, isp->cpd_fw_name,
+			      &isp->pdev->dev);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Requesting firmware(%s) failed\n",
+			isp->cpd_fw_name);
+		return rval;
+	}
+
+	rval = ipu_cpd_validate_cpd_file(isp, isp->cpd_fw->data,
+					 isp->cpd_fw->size);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Failed to validate cpd file\n");
+		goto out_release_firmware;
+	}
+
+	rval = ipu_buttress_map_fw_image(isp->psys, isp->cpd_fw, &psys->fw_sgt);
+	if (rval)
+		goto out_release_firmware;
+
+	psys->pkg_dir = ipu_cpd_create_pkg_dir(isp->psys,
+					       isp->cpd_fw->data,
+					       sg_dma_address(psys->fw_sgt.sgl),
+					       &psys->pkg_dir_dma_addr,
+					       &psys->pkg_dir_size);
+
+	if (!psys->pkg_dir) {
+		rval = -EINVAL;
+		goto out_unmap_fw_image;
+	}
+
+	isp->pkg_dir = psys->pkg_dir;
+	isp->pkg_dir_dma_addr = psys->pkg_dir_dma_addr;
+	isp->pkg_dir_size = psys->pkg_dir_size;
+
+	if (!isp->secure_mode)
+		return 0;
+
+	rval = ipu_fw_authenticate(isp, 1);
+	if (rval)
+		goto out_free_pkg_dir;
+
+	return 0;
+
+out_free_pkg_dir:
+	ipu_cpd_free_pkg_dir(isp->psys, psys->pkg_dir,
+			     psys->pkg_dir_dma_addr, psys->pkg_dir_size);
+out_unmap_fw_image:
+	ipu_buttress_unmap_fw_image(isp->psys, &psys->fw_sgt);
+out_release_firmware:
+	release_firmware(isp->cpd_fw);
+	isp->cpd_fw = NULL;
+
+	return rval;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static int ipu_psys_icache_prefetch_sp_get(void *data, u64 *val)
+{
+	struct ipu_psys *psys = data;
+
+	*val = psys->icache_prefetch_sp;
+	return 0;
+}
+
+static int ipu_psys_icache_prefetch_sp_set(void *data, u64 val)
+{
+	struct ipu_psys *psys = data;
+
+	if (val != !!val)
+		return -EINVAL;
+
+	psys->icache_prefetch_sp = val;
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(psys_icache_prefetch_sp_fops,
+			ipu_psys_icache_prefetch_sp_get,
+			ipu_psys_icache_prefetch_sp_set, "%llu\n");
+
+static int ipu_psys_icache_prefetch_isp_get(void *data, u64 *val)
+{
+	struct ipu_psys *psys = data;
+
+	*val = psys->icache_prefetch_isp;
+	return 0;
+}
+
+static int ipu_psys_icache_prefetch_isp_set(void *data, u64 val)
+{
+	struct ipu_psys *psys = data;
+
+	if (val != !!val)
+		return -EINVAL;
+
+	psys->icache_prefetch_isp = val;
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(psys_icache_prefetch_isp_fops,
+			ipu_psys_icache_prefetch_isp_get,
+			ipu_psys_icache_prefetch_isp_set, "%llu\n");
+
+static int ipu_psys_init_debugfs(struct ipu_psys *psys)
+{
+	struct dentry *file;
+	struct dentry *dir;
+
+	dir = debugfs_create_dir("psys", psys->adev->isp->ipu_dir);
+	if (IS_ERR(dir))
+		return -ENOMEM;
+
+	file = debugfs_create_file("icache_prefetch_sp", 0600,
+				   dir, psys, &psys_icache_prefetch_sp_fops);
+	if (IS_ERR(file))
+		goto err;
+
+	file = debugfs_create_file("icache_prefetch_isp", 0600,
+				   dir, psys, &psys_icache_prefetch_isp_fops);
+	if (IS_ERR(file))
+		goto err;
+
+	psys->debugfsdir = dir;
+
+#ifdef IPU_PSYS_GPC
+	if (ipu_psys_gpc_init_debugfs(psys))
+		return -ENOMEM;
+#endif
+
+	return 0;
+err:
+	debugfs_remove_recursive(dir);
+	return -ENOMEM;
+}
+#endif
+
+static int ipu_psys_sched_cmd(void *ptr)
+{
+	struct ipu_psys *psys = ptr;
+	size_t pending = 0;
+
+	while (1) {
+		wait_event_interruptible(psys->sched_cmd_wq,
+					 (kthread_should_stop() ||
+					  (pending =
+					   atomic_read(&psys->wakeup_count))));
+
+		if (kthread_should_stop())
+			break;
+
+		if (pending == 0)
+			continue;
+
+		mutex_lock(&psys->mutex);
+		atomic_set(&psys->wakeup_count, 0);
+		ipu_psys_run_next(psys);
+		mutex_unlock(&psys->mutex);
+	}
+
+	return 0;
+}
+
+static void start_sp(struct ipu_bus_device *adev)
+{
+	struct ipu_psys *psys = ipu_bus_get_drvdata(adev);
+	void __iomem *spc_regs_base = psys->pdata->base +
+	    psys->pdata->ipdata->hw_variant.spc_offset;
+	u32 val = 0;
+
+	val |= IPU_PSYS_SPC_STATUS_START |
+	    IPU_PSYS_SPC_STATUS_RUN |
+	    IPU_PSYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE;
+	val |= psys->icache_prefetch_sp ?
+	    IPU_PSYS_SPC_STATUS_ICACHE_PREFETCH : 0;
+	writel(val, spc_regs_base + IPU_PSYS_REG_SPC_STATUS_CTRL);
+}
+
+static int query_sp(struct ipu_bus_device *adev)
+{
+	struct ipu_psys *psys = ipu_bus_get_drvdata(adev);
+	void __iomem *spc_regs_base = psys->pdata->base +
+	    psys->pdata->ipdata->hw_variant.spc_offset;
+	u32 val = readl(spc_regs_base + IPU_PSYS_REG_SPC_STATUS_CTRL);
+
+	/* return true when READY == 1, START == 0 */
+	val &= IPU_PSYS_SPC_STATUS_READY | IPU_PSYS_SPC_STATUS_START;
+
+	return val == IPU_PSYS_SPC_STATUS_READY;
+}
+
+static int ipu_psys_fw_init(struct ipu_psys *psys)
+{
+	unsigned int size;
+	struct ipu_fw_syscom_queue_config *queue_cfg;
+	struct ipu_fw_syscom_queue_config fw_psys_event_queue_cfg[] = {
+		{
+			IPU_FW_PSYS_EVENT_QUEUE_SIZE,
+			sizeof(struct ipu_fw_psys_event)
+		}
+	};
+	struct ipu_fw_psys_srv_init server_init = {
+		.ddr_pkg_dir_address = 0,
+		.host_ddr_pkg_dir = NULL,
+		.pkg_dir_size = 0,
+		.icache_prefetch_sp = psys->icache_prefetch_sp,
+		.icache_prefetch_isp = psys->icache_prefetch_isp,
+	};
+	struct ipu_fw_com_cfg fwcom = {
+		.num_output_queues = IPU_FW_PSYS_N_PSYS_EVENT_QUEUE_ID,
+		.output = fw_psys_event_queue_cfg,
+		.specific_addr = &server_init,
+		.specific_size = sizeof(server_init),
+		.cell_start = start_sp,
+		.cell_ready = query_sp,
+		.buttress_boot_offset = SYSCOM_BUTTRESS_FW_PARAMS_PSYS_OFFSET,
+	};
+	int i;
+
+	size = IPU6SE_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+	if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP)
+		size = IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+
+	queue_cfg = devm_kzalloc(&psys->adev->dev, sizeof(*queue_cfg) * size,
+				 GFP_KERNEL);
+	if (!queue_cfg)
+		return -ENOMEM;
+
+	for (i = 0; i < size; i++) {
+		queue_cfg[i].queue_size = IPU_FW_PSYS_CMD_QUEUE_SIZE;
+		queue_cfg[i].token_size = sizeof(struct ipu_fw_psys_cmd);
+	}
+
+	fwcom.input = queue_cfg;
+	fwcom.num_input_queues = size;
+	fwcom.dmem_addr = psys->pdata->ipdata->hw_variant.dmem_offset;
+
+	psys->fwcom = ipu_fw_com_prepare(&fwcom, psys->adev, psys->pdata->base);
+	if (!psys->fwcom) {
+		dev_err(&psys->adev->dev, "psys fw com prepare failed\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static void run_fw_init_work(struct work_struct *work)
+{
+	struct fw_init_task *task = (struct fw_init_task *)work;
+	struct ipu_psys *psys = task->psys;
+	int rval;
+
+	rval = ipu_psys_fw_init(psys);
+
+	if (rval) {
+		dev_err(&psys->adev->dev, "FW init failed(%d)\n", rval);
+		ipu_psys_remove(psys->adev);
+	} else {
+		dev_info(&psys->adev->dev, "FW init done\n");
+	}
+}
+
+static int ipu_psys_probe(struct ipu_bus_device *adev)
+{
+	struct ipu_device *isp = adev->isp;
+	struct ipu_psys_pg *kpg, *kpg0;
+	struct ipu_psys *psys;
+	unsigned int minor;
+	int i, rval = -E2BIG;
+
+	rval = ipu_mmu_hw_init(adev->mmu);
+	if (rval)
+		return rval;
+
+	mutex_lock(&ipu_psys_mutex);
+
+	minor = find_next_zero_bit(ipu_psys_devices, IPU_PSYS_NUM_DEVICES, 0);
+	if (minor == IPU_PSYS_NUM_DEVICES) {
+		dev_err(&adev->dev, "too many devices\n");
+		goto out_unlock;
+	}
+
+	psys = devm_kzalloc(&adev->dev, sizeof(*psys), GFP_KERNEL);
+	if (!psys) {
+		rval = -ENOMEM;
+		goto out_unlock;
+	}
+
+	psys->adev = adev;
+	psys->pdata = adev->pdata;
+	psys->icache_prefetch_sp = 0;
+
+	psys->power_gating = 0;
+
+	ipu_trace_init(adev->isp, psys->pdata->base, &adev->dev,
+		       psys_trace_blocks);
+
+	cdev_init(&psys->cdev, &ipu_psys_fops);
+	psys->cdev.owner = ipu_psys_fops.owner;
+
+	rval = cdev_add(&psys->cdev, MKDEV(MAJOR(ipu_psys_dev_t), minor), 1);
+	if (rval) {
+		dev_err(&adev->dev, "cdev_add failed (%d)\n", rval);
+		goto out_unlock;
+	}
+
+	set_bit(minor, ipu_psys_devices);
+
+	spin_lock_init(&psys->ready_lock);
+	spin_lock_init(&psys->pgs_lock);
+	psys->ready = 0;
+	psys->timeout = IPU_PSYS_CMD_TIMEOUT_MS;
+
+	mutex_init(&psys->mutex);
+	INIT_LIST_HEAD(&psys->fhs);
+	INIT_LIST_HEAD(&psys->pgs);
+	INIT_LIST_HEAD(&psys->started_kcmds_list);
+
+	init_waitqueue_head(&psys->sched_cmd_wq);
+	atomic_set(&psys->wakeup_count, 0);
+	/*
+	 * Create a thread to schedule commands sent to IPU firmware.
+	 * The thread reduces the coupling between the command scheduler
+	 * and queueing commands from the user to driver.
+	 */
+	psys->sched_cmd_thread = kthread_run(ipu_psys_sched_cmd, psys,
+					     "psys_sched_cmd");
+
+	if (IS_ERR(psys->sched_cmd_thread)) {
+		psys->sched_cmd_thread = NULL;
+		mutex_destroy(&psys->mutex);
+		goto out_unlock;
+	}
+
+	ipu_bus_set_drvdata(adev, psys);
+
+	rval = ipu_psys_resource_pool_init(&psys->resource_pool_running);
+	if (rval < 0) {
+		dev_err(&psys->dev,
+			"unable to alloc process group resources\n");
+		goto out_mutex_destroy;
+	}
+
+	ipu6_psys_hw_res_variant_init();
+	psys->pkg_dir = isp->pkg_dir;
+	psys->pkg_dir_dma_addr = isp->pkg_dir_dma_addr;
+	psys->pkg_dir_size = isp->pkg_dir_size;
+	psys->fw_sgt = isp->fw_sgt;
+
+	/* allocate and map memory for process groups */
+	for (i = 0; i < IPU_PSYS_PG_POOL_SIZE; i++) {
+		kpg = kzalloc(sizeof(*kpg), GFP_KERNEL);
+		if (!kpg)
+			goto out_free_pgs;
+		kpg->pg = dma_alloc_attrs(&adev->dev,
+					  IPU_PSYS_PG_MAX_SIZE,
+					  &kpg->pg_dma_addr,
+					  GFP_KERNEL, 0);
+		if (!kpg->pg) {
+			kfree(kpg);
+			goto out_free_pgs;
+		}
+		kpg->size = IPU_PSYS_PG_MAX_SIZE;
+		list_add(&kpg->list, &psys->pgs);
+	}
+
+	psys->caps.pg_count = ipu_cpd_pkg_dir_get_num_entries(psys->pkg_dir);
+
+	dev_info(&adev->dev, "pkg_dir entry count:%d\n", psys->caps.pg_count);
+	if (async_fw_init) {
+		INIT_DELAYED_WORK((struct delayed_work *)&fw_init_task,
+				  run_fw_init_work);
+		fw_init_task.psys = psys;
+		schedule_delayed_work((struct delayed_work *)&fw_init_task, 0);
+	} else {
+		rval = ipu_psys_fw_init(psys);
+	}
+
+	if (rval) {
+		dev_err(&adev->dev, "FW init failed(%d)\n", rval);
+		goto out_free_pgs;
+	}
+
+	psys->dev.parent = &adev->dev;
+	psys->dev.bus = &ipu_psys_bus;
+	psys->dev.devt = MKDEV(MAJOR(ipu_psys_dev_t), minor);
+	psys->dev.release = ipu_psys_dev_release;
+	dev_set_name(&psys->dev, "ipu-psys%d", minor);
+	rval = device_register(&psys->dev);
+	if (rval < 0) {
+		dev_err(&psys->dev, "psys device_register failed\n");
+		goto out_release_fw_com;
+	}
+
+	/* Add the hw stepping information to caps */
+	strlcpy(psys->caps.dev_model, IPU_MEDIA_DEV_MODEL_NAME,
+		sizeof(psys->caps.dev_model));
+
+	pm_runtime_set_autosuspend_delay(&psys->adev->dev,
+					 IPU_PSYS_AUTOSUSPEND_DELAY);
+	pm_runtime_use_autosuspend(&psys->adev->dev);
+	pm_runtime_mark_last_busy(&psys->adev->dev);
+
+	mutex_unlock(&ipu_psys_mutex);
+
+#ifdef CONFIG_DEBUG_FS
+	/* Debug fs failure is not fatal. */
+	ipu_psys_init_debugfs(psys);
+#endif
+
+	adev->isp->cpd_fw_reload = &cpd_fw_reload;
+
+	dev_info(&adev->dev, "psys probe minor: %d\n", minor);
+
+	ipu_mmu_hw_cleanup(adev->mmu);
+
+	return 0;
+
+out_release_fw_com:
+	ipu_fw_com_release(psys->fwcom, 1);
+out_free_pgs:
+	list_for_each_entry_safe(kpg, kpg0, &psys->pgs, list) {
+		dma_free_attrs(&adev->dev, kpg->size, kpg->pg,
+			       kpg->pg_dma_addr, 0);
+		kfree(kpg);
+	}
+
+	ipu_psys_resource_pool_cleanup(&psys->resource_pool_running);
+out_mutex_destroy:
+	mutex_destroy(&psys->mutex);
+	cdev_del(&psys->cdev);
+	if (psys->sched_cmd_thread) {
+		kthread_stop(psys->sched_cmd_thread);
+		psys->sched_cmd_thread = NULL;
+	}
+out_unlock:
+	/* Safe to call even if the init is not called */
+	ipu_trace_uninit(&adev->dev);
+	mutex_unlock(&ipu_psys_mutex);
+
+	ipu_mmu_hw_cleanup(adev->mmu);
+
+	return rval;
+}
+
+static void ipu_psys_remove(struct ipu_bus_device *adev)
+{
+	struct ipu_device *isp = adev->isp;
+	struct ipu_psys *psys = ipu_bus_get_drvdata(adev);
+	struct ipu_psys_pg *kpg, *kpg0;
+
+#ifdef CONFIG_DEBUG_FS
+	if (isp->ipu_dir)
+		debugfs_remove_recursive(psys->debugfsdir);
+#endif
+
+	flush_workqueue(IPU_PSYS_WORK_QUEUE);
+
+	if (psys->sched_cmd_thread) {
+		kthread_stop(psys->sched_cmd_thread);
+		psys->sched_cmd_thread = NULL;
+	}
+
+	pm_runtime_dont_use_autosuspend(&psys->adev->dev);
+
+	mutex_lock(&ipu_psys_mutex);
+
+	list_for_each_entry_safe(kpg, kpg0, &psys->pgs, list) {
+		dma_free_attrs(&adev->dev, kpg->size, kpg->pg,
+			       kpg->pg_dma_addr, 0);
+		kfree(kpg);
+	}
+
+	if (psys->fwcom && ipu_fw_com_release(psys->fwcom, 1))
+		dev_err(&adev->dev, "fw com release failed.\n");
+
+	kfree(psys->server_init);
+	kfree(psys->syscom_config);
+
+	ipu_trace_uninit(&adev->dev);
+
+	ipu_psys_resource_pool_cleanup(&psys->resource_pool_running);
+
+	device_unregister(&psys->dev);
+
+	clear_bit(MINOR(psys->cdev.dev), ipu_psys_devices);
+	cdev_del(&psys->cdev);
+
+	mutex_unlock(&ipu_psys_mutex);
+
+	mutex_destroy(&psys->mutex);
+
+	dev_info(&adev->dev, "removed\n");
+}
+
+static irqreturn_t psys_isr_threaded(struct ipu_bus_device *adev)
+{
+	struct ipu_psys *psys = ipu_bus_get_drvdata(adev);
+	void __iomem *base = psys->pdata->base;
+	u32 status;
+	int r;
+
+	mutex_lock(&psys->mutex);
+#ifdef CONFIG_PM
+	r = pm_runtime_get_if_in_use(&psys->adev->dev);
+	if (!r || WARN_ON_ONCE(r < 0)) {
+		mutex_unlock(&psys->mutex);
+		return IRQ_NONE;
+	}
+#endif
+
+	status = readl(base + IPU_REG_PSYS_GPDEV_IRQ_STATUS);
+	writel(status, base + IPU_REG_PSYS_GPDEV_IRQ_CLEAR);
+
+	if (status & IPU_PSYS_GPDEV_IRQ_FWIRQ(IPU_PSYS_GPDEV_FWIRQ0)) {
+		writel(0, base + IPU_REG_PSYS_GPDEV_FWIRQ(0));
+		ipu_psys_handle_events(psys);
+	}
+
+	pm_runtime_mark_last_busy(&psys->adev->dev);
+	pm_runtime_put_autosuspend(&psys->adev->dev);
+	mutex_unlock(&psys->mutex);
+
+	return status ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static struct ipu_bus_driver ipu_psys_driver = {
+	.probe = ipu_psys_probe,
+	.remove = ipu_psys_remove,
+	.isr_threaded = psys_isr_threaded,
+	.wanted = IPU_PSYS_NAME,
+	.drv = {
+		.name = IPU_PSYS_NAME,
+		.owner = THIS_MODULE,
+		.pm = PSYS_PM_OPS,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+
+static int __init ipu_psys_init(void)
+{
+	int rval = alloc_chrdev_region(&ipu_psys_dev_t, 0,
+				       IPU_PSYS_NUM_DEVICES, IPU_PSYS_NAME);
+	if (rval) {
+		pr_err("can't alloc psys chrdev region (%d)\n", rval);
+		return rval;
+	}
+
+	rval = bus_register(&ipu_psys_bus);
+	if (rval) {
+		pr_warn("can't register psys bus (%d)\n", rval);
+		goto out_bus_register;
+	}
+
+	ipu_bus_register_driver(&ipu_psys_driver);
+
+	return rval;
+
+out_bus_register:
+	unregister_chrdev_region(ipu_psys_dev_t, IPU_PSYS_NUM_DEVICES);
+
+	return rval;
+}
+
+static void __exit ipu_psys_exit(void)
+{
+	ipu_bus_unregister_driver(&ipu_psys_driver);
+	bus_unregister(&ipu_psys_bus);
+	unregister_chrdev_region(ipu_psys_dev_t, IPU_PSYS_NUM_DEVICES);
+}
+
+static const struct pci_device_id ipu_pci_tbl[] = {
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6SE_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_ADL_P_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_ADL_N_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_RPL_P_PCI_ID)},
+	{0,}
+};
+MODULE_DEVICE_TABLE(pci, ipu_pci_tbl);
+
+module_init(ipu_psys_init);
+module_exit(ipu_psys_exit);
+
+MODULE_AUTHOR("Antti Laakso <antti.laakso@intel.com>");
+MODULE_AUTHOR("Bin Han <bin.b.han@intel.com>");
+MODULE_AUTHOR("Renwei Wu <renwei.wu@intel.com>");
+MODULE_AUTHOR("Jianxu Zheng <jian.xu.zheng@intel.com>");
+MODULE_AUTHOR("Xia Wu <xia.wu@intel.com>");
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_AUTHOR("Zaikuo Wang <zaikuo.wang@intel.com>");
+MODULE_AUTHOR("Yunliang Ding <yunliang.ding@intel.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel ipu processing system driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-psys.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-psys.h
@@ -0,0 +1,217 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_PSYS_H
+#define IPU_PSYS_H
+
+#include <linux/cdev.h>
+#include <linux/workqueue.h>
+
+#include "ipu.h"
+#include "ipu-pdata.h"
+#include "ipu-fw-psys.h"
+#include "ipu-platform-psys.h"
+
+#define IPU_PSYS_PG_POOL_SIZE 16
+#define IPU_PSYS_PG_MAX_SIZE 8192
+#define IPU_MAX_PSYS_CMD_BUFFERS 32
+#define IPU_PSYS_EVENT_CMD_COMPLETE IPU_FW_PSYS_EVENT_TYPE_SUCCESS
+#define IPU_PSYS_EVENT_FRAGMENT_COMPLETE IPU_FW_PSYS_EVENT_TYPE_SUCCESS
+#define IPU_PSYS_CLOSE_TIMEOUT_US   50
+#define IPU_PSYS_CLOSE_TIMEOUT (100000 / IPU_PSYS_CLOSE_TIMEOUT_US)
+#define IPU_PSYS_WORK_QUEUE		system_power_efficient_wq
+#define IPU_MAX_RESOURCES 128
+
+/* Opaque structure. Do not access fields. */
+struct ipu_resource {
+	u32 id;
+	int elements;	/* Number of elements available to allocation */
+	unsigned long *bitmap;	/* Allocation bitmap, a bit for each element */
+};
+
+enum ipu_resource_type {
+	IPU_RESOURCE_DEV_CHN = 0,
+	IPU_RESOURCE_EXT_MEM,
+	IPU_RESOURCE_DFM
+};
+
+/* Allocation of resource(s) */
+/* Opaque structure. Do not access fields. */
+struct ipu_resource_alloc {
+	enum ipu_resource_type type;
+	struct ipu_resource *resource;
+	int elements;
+	int pos;
+};
+
+/*
+ * This struct represents all of the currently allocated
+ * resources from IPU model. It is used also for allocating
+ * resources for the next set of PGs to be run on IPU
+ * (ie. those PGs which are not yet being run and which don't
+ * yet reserve real IPU resources).
+ * Use larger array to cover existing resource quantity
+ */
+
+/* resource size may need expand for new resource model */
+struct ipu_psys_resource_pool {
+	u32 cells;	/* Bitmask of cells allocated */
+	struct ipu_resource dev_channels[16];
+	struct ipu_resource ext_memory[32];
+	struct ipu_resource dfms[16];
+	DECLARE_BITMAP(cmd_queues, 32);
+	/* Protects cmd_queues bitmap */
+	spinlock_t queues_lock;
+};
+
+/*
+ * This struct keeps book of the resources allocated for a specific PG.
+ * It is used for freeing up resources from struct ipu_psys_resources
+ * when the PG is released from IPU (or model of IPU).
+ */
+struct ipu_psys_resource_alloc {
+	u32 cells;	/* Bitmask of cells needed */
+	struct ipu_resource_alloc
+	 resource_alloc[IPU_MAX_RESOURCES];
+	int resources;
+};
+
+struct task_struct;
+struct ipu_psys {
+	struct ipu_psys_capability caps;
+	struct cdev cdev;
+	struct device dev;
+
+	struct mutex mutex;	/* Psys various */
+	int ready; /* psys fw status */
+	bool icache_prefetch_sp;
+	bool icache_prefetch_isp;
+	spinlock_t ready_lock;	/* protect psys firmware state */
+	spinlock_t pgs_lock;	/* Protect pgs list access */
+	struct list_head fhs;
+	struct list_head pgs;
+	struct list_head started_kcmds_list;
+	struct ipu_psys_pdata *pdata;
+	struct ipu_bus_device *adev;
+	struct ia_css_syscom_context *dev_ctx;
+	struct ia_css_syscom_config *syscom_config;
+	struct ia_css_psys_server_init *server_init;
+	struct task_struct *sched_cmd_thread;
+	wait_queue_head_t sched_cmd_wq;
+	atomic_t wakeup_count;  /* Psys schedule thread wakeup count */
+#ifdef CONFIG_DEBUG_FS
+	struct dentry *debugfsdir;
+#endif
+
+	/* Resources needed to be managed for process groups */
+	struct ipu_psys_resource_pool resource_pool_running;
+
+	const struct firmware *fw;
+	struct sg_table fw_sgt;
+	u64 *pkg_dir;
+	dma_addr_t pkg_dir_dma_addr;
+	unsigned int pkg_dir_size;
+	unsigned long timeout;
+
+	int active_kcmds, started_kcmds;
+	void *fwcom;
+
+	int power_gating;
+};
+
+struct ipu_psys_fh {
+	struct ipu_psys *psys;
+	struct mutex mutex;	/* Protects bufmap & kcmds fields */
+	struct list_head list;
+	struct list_head bufmap;
+	wait_queue_head_t wait;
+	struct ipu_psys_scheduler sched;
+};
+
+struct ipu_psys_pg {
+	struct ipu_fw_psys_process_group *pg;
+	size_t size;
+	size_t pg_size;
+	dma_addr_t pg_dma_addr;
+	struct list_head list;
+	struct ipu_psys_resource_alloc resource_alloc;
+};
+
+struct ipu_psys_kcmd {
+	struct ipu_psys_fh *fh;
+	struct list_head list;
+	struct ipu_psys_buffer_set *kbuf_set;
+	enum ipu_psys_cmd_state state;
+	void *pg_manifest;
+	size_t pg_manifest_size;
+	struct ipu_psys_kbuffer **kbufs;
+	struct ipu_psys_buffer *buffers;
+	size_t nbuffers;
+	struct ipu_fw_psys_process_group *pg_user;
+	struct ipu_psys_pg *kpg;
+	u64 user_token;
+	u64 issue_id;
+	u32 priority;
+	u32 kernel_enable_bitmap[4];
+	u32 terminal_enable_bitmap[4];
+	u32 routing_enable_bitmap[4];
+	u32 rbm[5];
+	struct ipu_buttress_constraint constraint;
+	struct ipu_psys_event ev;
+	struct timer_list watchdog;
+};
+
+struct ipu_dma_buf_attach {
+	struct device *dev;
+	u64 len;
+	void *userptr;
+	struct sg_table *sgt;
+	bool vma_is_io;
+	struct page **pages;
+	size_t npages;
+};
+
+struct ipu_psys_kbuffer {
+	u64 len;
+	void *userptr;
+	u32 flags;
+	int fd;
+	void *kaddr;
+	struct list_head list;
+	dma_addr_t dma_addr;
+	struct sg_table *sgt;
+	struct dma_buf_attachment *db_attach;
+	struct dma_buf *dbuf;
+	bool valid;	/* True when buffer is usable */
+};
+
+#define inode_to_ipu_psys(inode) \
+	container_of((inode)->i_cdev, struct ipu_psys, cdev)
+
+#ifdef CONFIG_COMPAT
+long ipu_psys_compat_ioctl32(struct file *file, unsigned int cmd,
+			     unsigned long arg);
+#endif
+
+void ipu_psys_setup_hw(struct ipu_psys *psys);
+void ipu_psys_subdomains_power(struct ipu_psys *psys, bool on);
+void ipu_psys_handle_events(struct ipu_psys *psys);
+int ipu_psys_kcmd_new(struct ipu_psys_command *cmd, struct ipu_psys_fh *fh);
+void ipu_psys_run_next(struct ipu_psys *psys);
+struct ipu_psys_pg *__get_pg_buf(struct ipu_psys *psys, size_t pg_size);
+struct ipu_psys_kbuffer *
+ipu_psys_lookup_kbuffer(struct ipu_psys_fh *fh, int fd);
+int ipu_psys_mapbuf_locked(int fd, struct ipu_psys_fh *fh,
+			   struct ipu_psys_kbuffer *kbuf);
+struct ipu_psys_kbuffer *
+ipu_psys_lookup_kbuffer_by_kaddr(struct ipu_psys_fh *fh, void *kaddr);
+#ifdef IPU_PSYS_GPC
+int ipu_psys_gpc_init_debugfs(struct ipu_psys *psys);
+#endif
+int ipu_psys_resource_pool_init(struct ipu_psys_resource_pool *pool);
+void ipu_psys_resource_pool_cleanup(struct ipu_psys_resource_pool *pool);
+struct ipu_psys_kcmd *ipu_get_completed_kcmd(struct ipu_psys_fh *fh);
+long ipu_ioctl_dqevent(struct ipu_psys_event *event,
+		       struct ipu_psys_fh *fh, unsigned int f_flags);
+
+#endif /* IPU_PSYS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-trace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-trace.c
@@ -0,0 +1,869 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2014 - 2021 Intel Corporation
+
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/sizes.h>
+#include <linux/uaccess.h>
+#include <linux/vmalloc.h>
+
+#include "ipu.h"
+#include "ipu-platform-regs.h"
+#include "ipu-trace.h"
+
+struct trace_register_range {
+	u32 start;
+	u32 end;
+};
+
+#define MEMORY_RING_BUFFER_SIZE		(SZ_1M * 32)
+#define TRACE_MESSAGE_SIZE		16
+/*
+ * It looks that the trace unit sometimes writes outside the given buffer.
+ * To avoid memory corruption one extra page is reserved at the end
+ * of the buffer. Read also the extra area since it may contain valid data.
+ */
+#define MEMORY_RING_BUFFER_GUARD	PAGE_SIZE
+#define MEMORY_RING_BUFFER_OVERREAD	MEMORY_RING_BUFFER_GUARD
+#define MAX_TRACE_REGISTERS		200
+#define TRACE_CONF_DUMP_BUFFER_SIZE	(MAX_TRACE_REGISTERS * 2 * 32)
+#define TRACE_CONF_DATA_MAX_LEN		(1024 * 4)
+#define WPT_TRACE_CONF_DATA_MAX_LEN	(1024 * 64)
+
+struct config_value {
+	u32 reg;
+	u32 value;
+};
+
+struct ipu_trace_buffer {
+	dma_addr_t dma_handle;
+	void *memory_buffer;
+};
+
+struct ipu_subsystem_wptrace_config {
+	bool open;
+	char *conf_dump_buffer;
+	int size_conf_dump;
+	unsigned int fill_level;
+	struct config_value config[MAX_TRACE_REGISTERS];
+};
+
+struct ipu_subsystem_trace_config {
+	u32 offset;
+	void __iomem *base;
+	struct ipu_trace_buffer memory;	/* ring buffer */
+	struct device *dev;
+	struct ipu_trace_block *blocks;
+	unsigned int fill_level;	/* Nbr of regs in config table below */
+	bool running;
+	/* Cached register values  */
+	struct config_value config[MAX_TRACE_REGISTERS];
+	/* watchpoint trace info */
+	struct ipu_subsystem_wptrace_config wpt;
+};
+
+struct ipu_trace {
+	struct mutex lock; /* Protect ipu trace operations */
+	bool open;
+	char *conf_dump_buffer;
+	int size_conf_dump;
+
+	struct ipu_subsystem_trace_config isys;
+	struct ipu_subsystem_trace_config psys;
+};
+
+static void __ipu_trace_restore(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_device *isp = adev->isp;
+	struct ipu_trace *trace = isp->trace;
+	struct config_value *config;
+	struct ipu_subsystem_trace_config *sys = adev->trace_cfg;
+	struct ipu_trace_block *blocks;
+	u32 mapped_trace_buffer;
+	void __iomem *addr = NULL;
+	int i;
+
+	if (trace->open) {
+		dev_info(dev, "Trace control file open. Skipping update\n");
+		return;
+	}
+
+	if (!sys)
+		return;
+
+	/* leave if no trace configuration for this subsystem */
+	if (sys->fill_level == 0)
+		return;
+
+	/* Find trace unit base address */
+	blocks = sys->blocks;
+	while (blocks->type != IPU_TRACE_BLOCK_END) {
+		if (blocks->type == IPU_TRACE_BLOCK_TUN) {
+			addr = sys->base + blocks->offset;
+			break;
+		}
+		blocks++;
+	}
+	if (!addr)
+		return;
+
+	if (!sys->memory.memory_buffer) {
+		sys->memory.memory_buffer =
+		    dma_alloc_coherent(dev, MEMORY_RING_BUFFER_SIZE +
+				       MEMORY_RING_BUFFER_GUARD,
+				       &sys->memory.dma_handle,
+				       GFP_KERNEL);
+	}
+
+	if (!sys->memory.memory_buffer) {
+		dev_err(dev, "No memory for tracing. Trace unit disabled\n");
+		return;
+	}
+
+	config = sys->config;
+	mapped_trace_buffer = sys->memory.dma_handle;
+
+	/* ring buffer base */
+	writel(mapped_trace_buffer, addr + TRACE_REG_TUN_DRAM_BASE_ADDR);
+
+	/* ring buffer end */
+	writel(mapped_trace_buffer + MEMORY_RING_BUFFER_SIZE -
+		   TRACE_MESSAGE_SIZE, addr + TRACE_REG_TUN_DRAM_END_ADDR);
+
+	/* Infobits for ddr trace */
+	writel(IPU_INFO_REQUEST_DESTINATION_PRIMARY,
+	       addr + TRACE_REG_TUN_DDR_INFO_VAL);
+
+	/* Find trace timer reset address */
+	addr = NULL;
+	blocks = sys->blocks;
+	while (blocks->type != IPU_TRACE_BLOCK_END) {
+		if (blocks->type == IPU_TRACE_TIMER_RST) {
+			addr = sys->base + blocks->offset;
+			break;
+		}
+		blocks++;
+	}
+	if (!addr) {
+		dev_err(dev, "No trace reset addr\n");
+		return;
+	}
+
+	/* Remove reset from trace timers */
+	writel(TRACE_REG_GPREG_TRACE_TIMER_RST_OFF, addr);
+
+	/* Register config received from userspace */
+	for (i = 0; i < sys->fill_level; i++) {
+		dev_dbg(dev,
+			"Trace restore: reg 0x%08x, value 0x%08x\n",
+			config[i].reg, config[i].value);
+		writel(config[i].value, isp->base + config[i].reg);
+	}
+
+	/* Register wpt config received from userspace, and only psys has wpt */
+	config = sys->wpt.config;
+	for (i = 0; i < sys->wpt.fill_level; i++) {
+		dev_dbg(dev, "Trace restore: reg 0x%08x, value 0x%08x\n",
+			config[i].reg, config[i].value);
+		writel(config[i].value, isp->base + config[i].reg);
+	}
+	sys->running = true;
+}
+
+void ipu_trace_restore(struct device *dev)
+{
+	struct ipu_trace *trace = to_ipu_bus_device(dev)->isp->trace;
+
+	if (!trace)
+		return;
+
+	mutex_lock(&trace->lock);
+	__ipu_trace_restore(dev);
+	mutex_unlock(&trace->lock);
+}
+EXPORT_SYMBOL_GPL(ipu_trace_restore);
+
+static void __ipu_trace_stop(struct device *dev)
+{
+	struct ipu_subsystem_trace_config *sys =
+	    to_ipu_bus_device(dev)->trace_cfg;
+	struct ipu_trace_block *blocks;
+
+	if (!sys)
+		return;
+
+	if (!sys->running)
+		return;
+	sys->running = false;
+
+	/* Turn off all the gpc blocks */
+	blocks = sys->blocks;
+	while (blocks->type != IPU_TRACE_BLOCK_END) {
+		if (blocks->type == IPU_TRACE_BLOCK_GPC) {
+			writel(0, sys->base + blocks->offset +
+				   TRACE_REG_GPC_OVERALL_ENABLE);
+		}
+		blocks++;
+	}
+
+	/* Turn off all the trace monitors */
+	blocks = sys->blocks;
+	while (blocks->type != IPU_TRACE_BLOCK_END) {
+		if (blocks->type == IPU_TRACE_BLOCK_TM) {
+			writel(0, sys->base + blocks->offset +
+				   TRACE_REG_TM_TRACE_ENABLE_NPK);
+
+			writel(0, sys->base + blocks->offset +
+				   TRACE_REG_TM_TRACE_ENABLE_DDR);
+		}
+		blocks++;
+	}
+
+	/* Turn off trace units */
+	blocks = sys->blocks;
+	while (blocks->type != IPU_TRACE_BLOCK_END) {
+		if (blocks->type == IPU_TRACE_BLOCK_TUN) {
+			writel(0, sys->base + blocks->offset +
+				   TRACE_REG_TUN_DDR_ENABLE);
+			writel(0, sys->base + blocks->offset +
+				   TRACE_REG_TUN_NPK_ENABLE);
+		}
+		blocks++;
+	}
+}
+
+void ipu_trace_stop(struct device *dev)
+{
+	struct ipu_trace *trace = to_ipu_bus_device(dev)->isp->trace;
+
+	if (!trace)
+		return;
+
+	mutex_lock(&trace->lock);
+	__ipu_trace_stop(dev);
+	mutex_unlock(&trace->lock);
+}
+EXPORT_SYMBOL_GPL(ipu_trace_stop);
+
+static int update_register_cache(struct ipu_device *isp, u32 reg, u32 value)
+{
+	struct ipu_trace *dctrl = isp->trace;
+	struct ipu_subsystem_trace_config *sys;
+	int rval = -EINVAL;
+
+	if (dctrl->isys.offset == dctrl->psys.offset) {
+		/* For the IPU with uniform address space */
+		if (reg >= IPU_ISYS_OFFSET &&
+		    reg < IPU_ISYS_OFFSET + TRACE_REG_MAX_ISYS_OFFSET)
+			sys = &dctrl->isys;
+		else if (reg >= IPU_PSYS_OFFSET &&
+			 reg < IPU_PSYS_OFFSET + TRACE_REG_MAX_PSYS_OFFSET)
+			sys = &dctrl->psys;
+		else
+			goto error;
+	} else {
+		if (dctrl->isys.offset &&
+		    reg >= dctrl->isys.offset &&
+		    reg < dctrl->isys.offset + TRACE_REG_MAX_ISYS_OFFSET)
+			sys = &dctrl->isys;
+		else if (dctrl->psys.offset &&
+			 reg >= dctrl->psys.offset &&
+			 reg < dctrl->psys.offset + TRACE_REG_MAX_PSYS_OFFSET)
+			sys = &dctrl->psys;
+		else
+			goto error;
+	}
+
+	if (sys->fill_level < MAX_TRACE_REGISTERS) {
+		dev_dbg(sys->dev,
+			"Trace reg addr 0x%08x value 0x%08x\n", reg, value);
+		sys->config[sys->fill_level].reg = reg;
+		sys->config[sys->fill_level].value = value;
+		sys->fill_level++;
+	} else {
+		rval = -ENOMEM;
+		goto error;
+	}
+	return 0;
+error:
+	dev_info(&isp->pdev->dev,
+		 "Trace register address 0x%08x ignored as invalid register\n",
+		 reg);
+	return rval;
+}
+
+static void traceconf_dump(struct ipu_device *isp)
+{
+	struct ipu_subsystem_trace_config *sys[2] = {
+		&isp->trace->isys,
+		&isp->trace->psys
+	};
+	int i, j, rem_size;
+	char *out;
+
+	isp->trace->size_conf_dump = 0;
+	out = isp->trace->conf_dump_buffer;
+	rem_size = TRACE_CONF_DUMP_BUFFER_SIZE;
+
+	for (j = 0; j < ARRAY_SIZE(sys); j++) {
+		for (i = 0; i < sys[j]->fill_level && rem_size > 0; i++) {
+			int bytes_print;
+			int n = snprintf(out, rem_size, "0x%08x = 0x%08x\n",
+					 sys[j]->config[i].reg,
+					 sys[j]->config[i].value);
+
+			bytes_print = min(n, rem_size - 1);
+			rem_size -= bytes_print;
+			out += bytes_print;
+		}
+	}
+	isp->trace->size_conf_dump = out - isp->trace->conf_dump_buffer;
+}
+
+static void clear_trace_buffer(struct ipu_subsystem_trace_config *sys)
+{
+	if (!sys->memory.memory_buffer)
+		return;
+
+	memset(sys->memory.memory_buffer, 0, MEMORY_RING_BUFFER_SIZE +
+	       MEMORY_RING_BUFFER_OVERREAD);
+
+	dma_sync_single_for_device(sys->dev,
+				   sys->memory.dma_handle,
+				   MEMORY_RING_BUFFER_SIZE +
+				   MEMORY_RING_BUFFER_GUARD, DMA_FROM_DEVICE);
+}
+
+static int traceconf_open(struct inode *inode, struct file *file)
+{
+	int ret;
+	struct ipu_device *isp;
+
+	if (!inode->i_private)
+		return -EACCES;
+
+	isp = inode->i_private;
+
+	ret = mutex_trylock(&isp->trace->lock);
+	if (!ret)
+		return -EBUSY;
+
+	if (isp->trace->open) {
+		mutex_unlock(&isp->trace->lock);
+		return -EBUSY;
+	}
+
+	file->private_data = isp;
+	isp->trace->open = 1;
+	if (file->f_mode & FMODE_WRITE) {
+		/* TBD: Allocate temp buffer for processing.
+		 * Push validated buffer to active config
+		 */
+
+		/* Forget old config if opened for write */
+		isp->trace->isys.fill_level = 0;
+		isp->trace->psys.fill_level = 0;
+		isp->trace->psys.wpt.fill_level = 0;
+	}
+
+	if (file->f_mode & FMODE_READ) {
+		isp->trace->conf_dump_buffer =
+		    vzalloc(TRACE_CONF_DUMP_BUFFER_SIZE);
+		if (!isp->trace->conf_dump_buffer) {
+			isp->trace->open = 0;
+			mutex_unlock(&isp->trace->lock);
+			return -ENOMEM;
+		}
+		traceconf_dump(isp);
+	}
+	mutex_unlock(&isp->trace->lock);
+	return 0;
+}
+
+static ssize_t traceconf_read(struct file *file, char __user *buf,
+			      size_t len, loff_t *ppos)
+{
+	struct ipu_device *isp = file->private_data;
+
+	return simple_read_from_buffer(buf, len, ppos,
+				       isp->trace->conf_dump_buffer,
+				       isp->trace->size_conf_dump);
+}
+
+static ssize_t traceconf_write(struct file *file, const char __user *buf,
+			       size_t len, loff_t *ppos)
+{
+	int i;
+	struct ipu_device *isp = file->private_data;
+	ssize_t bytes = 0;
+	char *ipu_trace_buffer = NULL;
+	size_t buffer_size = 0;
+	u32 ipu_trace_number = 0;
+	struct config_value *cfg_buffer = NULL;
+
+	if ((*ppos < 0) || (len > TRACE_CONF_DATA_MAX_LEN) ||
+	    (len < sizeof(ipu_trace_number))) {
+		dev_info(&isp->pdev->dev,
+			"length is error, len:%ld, loff:%lld\n",
+			len, *ppos);
+		return -EINVAL;
+	}
+
+	ipu_trace_buffer = vzalloc(len);
+	if (!ipu_trace_buffer)
+		return -ENOMEM;
+
+	bytes = copy_from_user(ipu_trace_buffer, buf, len);
+	if (bytes != 0) {
+		vfree(ipu_trace_buffer);
+		return -EFAULT;
+	}
+
+	memcpy(&ipu_trace_number, ipu_trace_buffer, sizeof(u32));
+	buffer_size = ipu_trace_number * sizeof(struct config_value);
+	if ((buffer_size + sizeof(ipu_trace_number)) != len) {
+		dev_info(&isp->pdev->dev,
+			"File size is not right, len:%ld, buffer_size:%zu\n",
+			len, buffer_size);
+		vfree(ipu_trace_buffer);
+		return -EFAULT;
+	}
+
+	mutex_lock(&isp->trace->lock);
+	cfg_buffer = (struct config_value *)(ipu_trace_buffer + sizeof(u32));
+	for (i = 0; i < ipu_trace_number; i++) {
+		update_register_cache(isp, cfg_buffer[i].reg,
+			cfg_buffer[i].value);
+	}
+	mutex_unlock(&isp->trace->lock);
+	vfree(ipu_trace_buffer);
+
+	return len;
+}
+
+static int traceconf_release(struct inode *inode, struct file *file)
+{
+	struct ipu_device *isp = file->private_data;
+	struct device *psys_dev = isp->psys ? &isp->psys->dev : NULL;
+	struct device *isys_dev = isp->isys ? &isp->isys->dev : NULL;
+	int pm_rval = -EINVAL;
+
+	/*
+	 * Turn devices on outside trace->lock mutex. PM transition may
+	 * cause call to function which tries to take the same lock.
+	 * Also do this before trace->open is set back to 0 to avoid
+	 * double restore (one here and one in pm transition). We can't
+	 * rely purely on the restore done by pm call backs since trace
+	 * configuration can occur in any phase compared to other activity.
+	 */
+
+	if (file->f_mode & FMODE_WRITE) {
+		if (isys_dev)
+			pm_rval = pm_runtime_get_sync(isys_dev);
+
+		if (pm_rval >= 0) {
+			/* ISYS ok or missing */
+			if (psys_dev)
+				pm_rval = pm_runtime_get_sync(psys_dev);
+
+			if (pm_rval < 0) {
+				pm_runtime_put_noidle(psys_dev);
+				if (isys_dev)
+					pm_runtime_put(isys_dev);
+			}
+		} else {
+			pm_runtime_put_noidle(&isp->isys->dev);
+		}
+	}
+
+	mutex_lock(&isp->trace->lock);
+	isp->trace->open = 0;
+	vfree(isp->trace->conf_dump_buffer);
+	isp->trace->conf_dump_buffer = NULL;
+
+	if (pm_rval >= 0) {
+		/* Update new cfg to HW */
+		if (isys_dev) {
+			__ipu_trace_stop(isys_dev);
+			clear_trace_buffer(isp->isys->trace_cfg);
+			__ipu_trace_restore(isys_dev);
+		}
+
+		if (psys_dev) {
+			__ipu_trace_stop(psys_dev);
+			clear_trace_buffer(isp->psys->trace_cfg);
+			__ipu_trace_restore(psys_dev);
+		}
+	}
+
+	mutex_unlock(&isp->trace->lock);
+
+	if (pm_rval >= 0) {
+		/* Again - this must be done with trace->lock not taken */
+		if (psys_dev)
+			pm_runtime_put(psys_dev);
+		if (isys_dev)
+			pm_runtime_put(isys_dev);
+	}
+	return 0;
+}
+
+static const struct file_operations ipu_traceconf_fops = {
+	.owner = THIS_MODULE,
+	.open = traceconf_open,
+	.release = traceconf_release,
+	.read = traceconf_read,
+	.write = traceconf_write,
+	.llseek = no_llseek,
+};
+
+static void wptraceconf_dump(struct ipu_device *isp)
+{
+	struct ipu_subsystem_wptrace_config *sys = &isp->trace->psys.wpt;
+	int i, rem_size;
+	char *out;
+
+	sys->size_conf_dump = 0;
+	out = sys->conf_dump_buffer;
+	rem_size = TRACE_CONF_DUMP_BUFFER_SIZE;
+
+	for (i = 0; i < sys->fill_level && rem_size > 0; i++) {
+		int bytes_print;
+		int n = snprintf(out, rem_size, "0x%08x = 0x%08x\n",
+				 sys->config[i].reg,
+				 sys->config[i].value);
+
+		bytes_print = min(n, rem_size - 1);
+		rem_size -= bytes_print;
+		out += bytes_print;
+	}
+	sys->size_conf_dump = out - sys->conf_dump_buffer;
+}
+
+static int wptraceconf_open(struct inode *inode, struct file *file)
+{
+	int ret;
+	struct ipu_device *isp;
+
+	if (!inode->i_private)
+		return -EACCES;
+
+	isp = inode->i_private;
+	ret = mutex_trylock(&isp->trace->lock);
+	if (!ret)
+		return -EBUSY;
+
+	if (isp->trace->psys.wpt.open) {
+		mutex_unlock(&isp->trace->lock);
+		return -EBUSY;
+	}
+
+	file->private_data = isp;
+	if (file->f_mode & FMODE_WRITE) {
+		/* TBD: Allocate temp buffer for processing.
+		 * Push validated buffer to active config
+		 */
+		/* Forget old config if opened for write */
+		isp->trace->psys.wpt.fill_level = 0;
+	}
+
+	if (file->f_mode & FMODE_READ) {
+		isp->trace->psys.wpt.conf_dump_buffer =
+		    vzalloc(TRACE_CONF_DUMP_BUFFER_SIZE);
+		if (!isp->trace->psys.wpt.conf_dump_buffer) {
+			mutex_unlock(&isp->trace->lock);
+			return -ENOMEM;
+		}
+		wptraceconf_dump(isp);
+	}
+	mutex_unlock(&isp->trace->lock);
+	return 0;
+}
+
+static ssize_t wptraceconf_read(struct file *file, char __user *buf,
+			      size_t len, loff_t *ppos)
+{
+	struct ipu_device *isp = file->private_data;
+
+	return simple_read_from_buffer(buf, len, ppos,
+				       isp->trace->psys.wpt.conf_dump_buffer,
+				       isp->trace->psys.wpt.size_conf_dump);
+}
+
+static ssize_t wptraceconf_write(struct file *file, const char __user *buf,
+			       size_t len, loff_t *ppos)
+{
+	int i;
+	struct ipu_device *isp = file->private_data;
+	ssize_t bytes = 0;
+	char *wpt_info_buffer = NULL;
+	size_t buffer_size = 0;
+	u32 wp_node_number = 0;
+	struct config_value *wpt_buffer = NULL;
+	struct ipu_subsystem_wptrace_config *wpt = &isp->trace->psys.wpt;
+
+	if ((*ppos < 0) || (len > WPT_TRACE_CONF_DATA_MAX_LEN) ||
+	    (len < sizeof(wp_node_number))) {
+		dev_info(&isp->pdev->dev,
+			"length is error, len:%ld, loff:%lld\n",
+			len, *ppos);
+		return -EINVAL;
+	}
+
+	wpt_info_buffer = vzalloc(len);
+	if (!wpt_info_buffer)
+		return -ENOMEM;
+
+	bytes = copy_from_user(wpt_info_buffer, buf, len);
+	if (bytes != 0) {
+		vfree(wpt_info_buffer);
+		return -EFAULT;
+	}
+
+	memcpy(&wp_node_number, wpt_info_buffer, sizeof(u32));
+	buffer_size = wp_node_number * sizeof(struct config_value);
+	if ((buffer_size + sizeof(wp_node_number)) != len) {
+		dev_info(&isp->pdev->dev,
+			"File size is not right, len:%ld, buffer_size:%zu\n",
+			len, buffer_size);
+		vfree(wpt_info_buffer);
+		return -EFAULT;
+	}
+
+	mutex_lock(&isp->trace->lock);
+	wpt_buffer = (struct config_value *)(wpt_info_buffer + sizeof(u32));
+	for (i = 0; i < wp_node_number; i++) {
+		if (wpt->fill_level < MAX_TRACE_REGISTERS) {
+			wpt->config[wpt->fill_level].reg = wpt_buffer[i].reg;
+			wpt->config[wpt->fill_level].value =
+				wpt_buffer[i].value;
+			wpt->fill_level++;
+		} else {
+			dev_info(&isp->pdev->dev,
+				 "Address 0x%08x ignored as invalid register\n",
+				 wpt_buffer[i].reg);
+			break;
+		}
+	}
+	mutex_unlock(&isp->trace->lock);
+	vfree(wpt_info_buffer);
+
+	return len;
+}
+
+static int wptraceconf_release(struct inode *inode, struct file *file)
+{
+	struct ipu_device *isp = file->private_data;
+
+	mutex_lock(&isp->trace->lock);
+	isp->trace->open = 0;
+	vfree(isp->trace->psys.wpt.conf_dump_buffer);
+	isp->trace->psys.wpt.conf_dump_buffer = NULL;
+	mutex_unlock(&isp->trace->lock);
+
+	return 0;
+}
+
+static const struct file_operations ipu_wptraceconf_fops = {
+	.owner = THIS_MODULE,
+	.open = wptraceconf_open,
+	.release = wptraceconf_release,
+	.read = wptraceconf_read,
+	.write = wptraceconf_write,
+	.llseek = no_llseek,
+};
+
+static int gettrace_open(struct inode *inode, struct file *file)
+{
+	struct ipu_subsystem_trace_config *sys = inode->i_private;
+
+	if (!sys)
+		return -EACCES;
+
+	if (!sys->memory.memory_buffer)
+		return -EACCES;
+
+	dma_sync_single_for_cpu(sys->dev,
+				sys->memory.dma_handle,
+				MEMORY_RING_BUFFER_SIZE +
+				MEMORY_RING_BUFFER_GUARD, DMA_FROM_DEVICE);
+
+	file->private_data = sys;
+	return 0;
+};
+
+static ssize_t gettrace_read(struct file *file, char __user *buf,
+			     size_t len, loff_t *ppos)
+{
+	struct ipu_subsystem_trace_config *sys = file->private_data;
+
+	return simple_read_from_buffer(buf, len, ppos,
+				       sys->memory.memory_buffer,
+				       MEMORY_RING_BUFFER_SIZE +
+				       MEMORY_RING_BUFFER_OVERREAD);
+}
+
+static ssize_t gettrace_write(struct file *file, const char __user *buf,
+			      size_t len, loff_t *ppos)
+{
+	struct ipu_subsystem_trace_config *sys = file->private_data;
+	static const char str[] = "clear";
+	char buffer[sizeof(str)] = { 0 };
+	ssize_t ret;
+
+	ret = simple_write_to_buffer(buffer, sizeof(buffer), ppos, buf, len);
+	if (ret < 0)
+		return ret;
+
+	if (ret < sizeof(str) - 1)
+		return -EINVAL;
+
+	if (!strncmp(str, buffer, sizeof(str) - 1)) {
+		clear_trace_buffer(sys);
+		return len;
+	}
+
+	return -EINVAL;
+}
+
+static int gettrace_release(struct inode *inode, struct file *file)
+{
+	return 0;
+}
+
+static const struct file_operations ipu_gettrace_fops = {
+	.owner = THIS_MODULE,
+	.open = gettrace_open,
+	.release = gettrace_release,
+	.read = gettrace_read,
+	.write = gettrace_write,
+	.llseek = no_llseek,
+};
+
+int ipu_trace_init(struct ipu_device *isp, void __iomem *base,
+		   struct device *dev, struct ipu_trace_block *blocks)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_trace *trace = isp->trace;
+	struct ipu_subsystem_trace_config *sys;
+	int ret = 0;
+
+	if (!isp->trace)
+		return 0;
+
+	mutex_lock(&isp->trace->lock);
+
+	if (dev == &isp->isys->dev) {
+		sys = &trace->isys;
+	} else if (dev == &isp->psys->dev) {
+		sys = &trace->psys;
+	} else {
+		ret = -EINVAL;
+		goto leave;
+	}
+
+	adev->trace_cfg = sys;
+	sys->dev = dev;
+	sys->offset = base - isp->base;	/* sub system offset */
+	sys->base = base;
+	sys->blocks = blocks;
+
+leave:
+	mutex_unlock(&isp->trace->lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(ipu_trace_init);
+
+void ipu_trace_uninit(struct device *dev)
+{
+	struct ipu_bus_device *adev = to_ipu_bus_device(dev);
+	struct ipu_device *isp = adev->isp;
+	struct ipu_trace *trace = isp->trace;
+	struct ipu_subsystem_trace_config *sys = adev->trace_cfg;
+
+	if (!trace || !sys)
+		return;
+
+	mutex_lock(&trace->lock);
+
+	if (sys->memory.memory_buffer)
+		dma_free_coherent(sys->dev,
+				  MEMORY_RING_BUFFER_SIZE +
+				  MEMORY_RING_BUFFER_GUARD,
+				  sys->memory.memory_buffer,
+				  sys->memory.dma_handle);
+
+	sys->dev = NULL;
+	sys->memory.memory_buffer = NULL;
+
+	mutex_unlock(&trace->lock);
+}
+EXPORT_SYMBOL_GPL(ipu_trace_uninit);
+
+int ipu_trace_debugfs_add(struct ipu_device *isp, struct dentry *dir)
+{
+	struct dentry *files[4];
+	int i = 0;
+
+	files[i] = debugfs_create_file("traceconf", 0644,
+				       dir, isp, &ipu_traceconf_fops);
+	if (!files[i])
+		return -ENOMEM;
+	i++;
+
+	files[i] = debugfs_create_file("wptraceconf", 0644,
+				       dir, isp, &ipu_wptraceconf_fops);
+	if (!files[i])
+		goto error;
+	i++;
+
+	files[i] = debugfs_create_file("getisystrace", 0444,
+				       dir,
+				       &isp->trace->isys, &ipu_gettrace_fops);
+
+	if (!files[i])
+		goto error;
+	i++;
+
+	files[i] = debugfs_create_file("getpsystrace", 0444,
+				       dir,
+				       &isp->trace->psys, &ipu_gettrace_fops);
+	if (!files[i])
+		goto error;
+
+	return 0;
+
+error:
+	for (; i > 0; i--)
+		debugfs_remove(files[i - 1]);
+	return -ENOMEM;
+}
+
+int ipu_trace_add(struct ipu_device *isp)
+{
+	isp->trace = devm_kzalloc(&isp->pdev->dev,
+				  sizeof(struct ipu_trace), GFP_KERNEL);
+	if (!isp->trace)
+		return -ENOMEM;
+
+	mutex_init(&isp->trace->lock);
+
+	return 0;
+}
+
+void ipu_trace_release(struct ipu_device *isp)
+{
+	if (!isp->trace)
+		return;
+	mutex_destroy(&isp->trace->lock);
+}
+
+MODULE_AUTHOR("Samu Onkalo <samu.onkalo@intel.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel ipu trace support");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu-trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu-trace.h
@@ -0,0 +1,146 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2014 - 2021 Intel Corporation */
+
+#ifndef IPU_TRACE_H
+#define IPU_TRACE_H
+#include <linux/debugfs.h>
+
+/* Trace unit register offsets */
+#define TRACE_REG_TUN_DDR_ENABLE        0x000
+#define TRACE_REG_TUN_NPK_ENABLE	0x004
+#define TRACE_REG_TUN_DDR_INFO_VAL	0x008
+#define TRACE_REG_TUN_NPK_ADDR		0x00C
+#define TRACE_REG_TUN_DRAM_BASE_ADDR	0x010
+#define TRACE_REG_TUN_DRAM_END_ADDR	0x014
+#define TRACE_REG_TUN_LOCAL_TIMER0	0x018
+#define TRACE_REG_TUN_LOCAL_TIMER1	0x01C
+#define TRACE_REG_TUN_WR_PTR		0x020
+#define TRACE_REG_TUN_RD_PTR		0x024
+
+/*
+ * Following registers are left out on purpose:
+ * TUN_LOCAL_TIMER0, TUN_LOCAL_TIMER1, TUN_DRAM_BASE_ADDR
+ * TUN_DRAM_END_ADDR, TUN_WR_PTR, TUN_RD_PTR
+ */
+
+/* Trace monitor register offsets */
+#define TRACE_REG_TM_TRACE_ADDR_A		0x0900
+#define TRACE_REG_TM_TRACE_ADDR_B		0x0904
+#define TRACE_REG_TM_TRACE_ADDR_C		0x0908
+#define TRACE_REG_TM_TRACE_ADDR_D		0x090c
+#define TRACE_REG_TM_TRACE_ENABLE_NPK		0x0910
+#define TRACE_REG_TM_TRACE_ENABLE_DDR		0x0914
+#define TRACE_REG_TM_TRACE_PER_PC		0x0918
+#define TRACE_REG_TM_TRACE_PER_BRANCH		0x091c
+#define TRACE_REG_TM_TRACE_HEADER		0x0920
+#define TRACE_REG_TM_TRACE_CFG			0x0924
+#define TRACE_REG_TM_TRACE_LOST_PACKETS		0x0928
+#define TRACE_REG_TM_TRACE_LP_CLEAR		0x092c
+#define TRACE_REG_TM_TRACE_LMRUN_MASK		0x0930
+#define TRACE_REG_TM_TRACE_LMRUN_PC_LOW		0x0934
+#define TRACE_REG_TM_TRACE_LMRUN_PC_HIGH	0x0938
+#define TRACE_REG_TM_TRACE_MMIO_SEL		0x093c
+#define TRACE_REG_TM_TRACE_MMIO_WP0_LOW		0x0940
+#define TRACE_REG_TM_TRACE_MMIO_WP1_LOW		0x0944
+#define TRACE_REG_TM_TRACE_MMIO_WP2_LOW		0x0948
+#define TRACE_REG_TM_TRACE_MMIO_WP3_LOW		0x094c
+#define TRACE_REG_TM_TRACE_MMIO_WP0_HIGH	0x0950
+#define TRACE_REG_TM_TRACE_MMIO_WP1_HIGH	0x0954
+#define TRACE_REG_TM_TRACE_MMIO_WP2_HIGH	0x0958
+#define TRACE_REG_TM_TRACE_MMIO_WP3_HIGH	0x095c
+#define TRACE_REG_TM_FWTRACE_FIRST		0x0A00
+#define TRACE_REG_TM_FWTRACE_MIDDLE		0x0A04
+#define TRACE_REG_TM_FWTRACE_LAST		0x0A08
+
+/*
+ * Following exists only in (I)SP address space:
+ * TM_FWTRACE_FIRST, TM_FWTRACE_MIDDLE, TM_FWTRACE_LAST
+ */
+
+#define TRACE_REG_GPC_RESET			0x000
+#define TRACE_REG_GPC_OVERALL_ENABLE		0x004
+#define TRACE_REG_GPC_TRACE_HEADER		0x008
+#define TRACE_REG_GPC_TRACE_ADDRESS		0x00C
+#define TRACE_REG_GPC_TRACE_NPK_EN		0x010
+#define TRACE_REG_GPC_TRACE_DDR_EN		0x014
+#define TRACE_REG_GPC_TRACE_LPKT_CLEAR		0x018
+#define TRACE_REG_GPC_TRACE_LPKT		0x01C
+
+#define TRACE_REG_GPC_ENABLE_ID0		0x020
+#define TRACE_REG_GPC_ENABLE_ID1		0x024
+#define TRACE_REG_GPC_ENABLE_ID2		0x028
+#define TRACE_REG_GPC_ENABLE_ID3		0x02c
+
+#define TRACE_REG_GPC_VALUE_ID0			0x030
+#define TRACE_REG_GPC_VALUE_ID1			0x034
+#define TRACE_REG_GPC_VALUE_ID2			0x038
+#define TRACE_REG_GPC_VALUE_ID3			0x03c
+
+#define TRACE_REG_GPC_CNT_INPUT_SELECT_ID0	0x040
+#define TRACE_REG_GPC_CNT_INPUT_SELECT_ID1	0x044
+#define TRACE_REG_GPC_CNT_INPUT_SELECT_ID2	0x048
+#define TRACE_REG_GPC_CNT_INPUT_SELECT_ID3	0x04c
+
+#define TRACE_REG_GPC_CNT_START_SELECT_ID0	0x050
+#define TRACE_REG_GPC_CNT_START_SELECT_ID1	0x054
+#define TRACE_REG_GPC_CNT_START_SELECT_ID2	0x058
+#define TRACE_REG_GPC_CNT_START_SELECT_ID3	0x05c
+
+#define TRACE_REG_GPC_CNT_STOP_SELECT_ID0	0x060
+#define TRACE_REG_GPC_CNT_STOP_SELECT_ID1	0x064
+#define TRACE_REG_GPC_CNT_STOP_SELECT_ID2	0x068
+#define TRACE_REG_GPC_CNT_STOP_SELECT_ID3	0x06c
+
+#define TRACE_REG_GPC_CNT_MSG_SELECT_ID0	0x070
+#define TRACE_REG_GPC_CNT_MSG_SELECT_ID1	0x074
+#define TRACE_REG_GPC_CNT_MSG_SELECT_ID2	0x078
+#define TRACE_REG_GPC_CNT_MSG_SELECT_ID3	0x07c
+
+#define TRACE_REG_GPC_CNT_MSG_PLOAD_SELECT_ID0	0x080
+#define TRACE_REG_GPC_CNT_MSG_PLOAD_SELECT_ID1	0x084
+#define TRACE_REG_GPC_CNT_MSG_PLOAD_SELECT_ID2	0x088
+#define TRACE_REG_GPC_CNT_MSG_PLOAD_SELECT_ID3	0x08c
+
+#define TRACE_REG_GPC_IRQ_TRIGGER_VALUE_ID0	0x090
+#define TRACE_REG_GPC_IRQ_TRIGGER_VALUE_ID1	0x094
+#define TRACE_REG_GPC_IRQ_TRIGGER_VALUE_ID2	0x098
+#define TRACE_REG_GPC_IRQ_TRIGGER_VALUE_ID3	0x09c
+
+#define TRACE_REG_GPC_IRQ_TIMER_SELECT_ID0	0x0a0
+#define TRACE_REG_GPC_IRQ_TIMER_SELECT_ID1	0x0a4
+#define TRACE_REG_GPC_IRQ_TIMER_SELECT_ID2	0x0a8
+#define TRACE_REG_GPC_IRQ_TIMER_SELECT_ID3	0x0ac
+
+#define TRACE_REG_GPC_IRQ_ENABLE_ID0		0x0b0
+#define TRACE_REG_GPC_IRQ_ENABLE_ID1		0x0b4
+#define TRACE_REG_GPC_IRQ_ENABLE_ID2		0x0b8
+#define TRACE_REG_GPC_IRQ_ENABLE_ID3		0x0bc
+
+struct ipu_trace;
+struct ipu_subsystem_trace_config;
+
+enum ipu_trace_block_type {
+	IPU_TRACE_BLOCK_TUN = 0,	/* Trace unit */
+	IPU_TRACE_BLOCK_TM,	/* Trace monitor */
+	IPU_TRACE_BLOCK_GPC,	/* General purpose control */
+	IPU_TRACE_CSI2,	/* CSI2 legacy receiver */
+	IPU_TRACE_CSI2_3PH,	/* CSI2 combo receiver */
+	IPU_TRACE_SIG2CIOS,
+	IPU_TRACE_TIMER_RST,	/* Trace reset control timer */
+	IPU_TRACE_BLOCK_END	/* End of list */
+};
+
+struct ipu_trace_block {
+	u32 offset;	/* Offset to block inside subsystem */
+	enum ipu_trace_block_type type;
+};
+
+int ipu_trace_add(struct ipu_device *isp);
+int ipu_trace_debugfs_add(struct ipu_device *isp, struct dentry *dir);
+void ipu_trace_release(struct ipu_device *isp);
+int ipu_trace_init(struct ipu_device *isp, void __iomem *base,
+		   struct device *dev, struct ipu_trace_block *blocks);
+void ipu_trace_restore(struct device *dev);
+void ipu_trace_uninit(struct device *dev);
+void ipu_trace_stop(struct device *dev);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu.c
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2013 - 2020 Intel Corporation
+
+#include <linux/acpi.h>
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/firmware.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pci.h>
+#include <linux/pm_qos.h>
+#include <linux/pm_runtime.h>
+#include <linux/timer.h>
+#include <linux/sched.h>
+
+#include "ipu.h"
+#include "ipu-buttress.h"
+#include "ipu-platform.h"
+#include "ipu-platform-buttress-regs.h"
+#include "ipu-cpd.h"
+#include "ipu-pdata.h"
+#include "ipu-bus.h"
+#include "ipu-mmu.h"
+#include "ipu-platform-regs.h"
+#include "ipu-platform-isys-csi2-reg.h"
+#include "ipu-trace.h"
+
+#define IPU_PCI_BAR		0
+enum ipu_version ipu_ver;
+EXPORT_SYMBOL(ipu_ver);
+
+static struct ipu_bus_device *ipu_isys_init(struct pci_dev *pdev,
+					    struct device *parent,
+					    struct ipu_buttress_ctrl *ctrl,
+					    void __iomem *base,
+					    const struct ipu_isys_internal_pdata
+					    *ipdata,
+					    unsigned int nr)
+{
+	struct ipu_bus_device *isys;
+	struct ipu_isys_pdata *pdata;
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return ERR_PTR(-ENOMEM);
+
+	pdata->base = base;
+	pdata->ipdata = ipdata;
+
+	/* Use 250MHz for ipu6 se */
+	if (ipu_ver == IPU_VER_6SE)
+		ctrl->ratio = IPU6SE_IS_FREQ_CTL_DEFAULT_RATIO;
+
+	isys = ipu_bus_add_device(pdev, parent, pdata, ctrl,
+				  IPU_ISYS_NAME, nr);
+	if (IS_ERR(isys))
+		return ERR_PTR(-ENOMEM);
+
+	isys->mmu = ipu_mmu_init(&pdev->dev, base, ISYS_MMID,
+				 &ipdata->hw_variant);
+	if (IS_ERR(isys->mmu))
+		return ERR_PTR(-ENOMEM);
+
+	isys->mmu->dev = &isys->dev;
+
+	return isys;
+}
+
+static struct ipu_bus_device *ipu_psys_init(struct pci_dev *pdev,
+					    struct device *parent,
+					    struct ipu_buttress_ctrl *ctrl,
+					    void __iomem *base,
+					    const struct ipu_psys_internal_pdata
+					    *ipdata, unsigned int nr)
+{
+	struct ipu_bus_device *psys;
+	struct ipu_psys_pdata *pdata;
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return ERR_PTR(-ENOMEM);
+
+	pdata->base = base;
+	pdata->ipdata = ipdata;
+
+	psys = ipu_bus_add_device(pdev, parent, pdata, ctrl,
+				  IPU_PSYS_NAME, nr);
+	if (IS_ERR(psys))
+		return ERR_PTR(-ENOMEM);
+
+	psys->mmu = ipu_mmu_init(&pdev->dev, base, PSYS_MMID,
+				 &ipdata->hw_variant);
+	if (IS_ERR(psys->mmu))
+		return ERR_PTR(-ENOMEM);
+
+	psys->mmu->dev = &psys->dev;
+
+	return psys;
+}
+
+int ipu_fw_authenticate(void *data, u64 val)
+{
+	struct ipu_device *isp = data;
+	int ret;
+
+	if (!isp->secure_mode)
+		return -EINVAL;
+
+	ret = ipu_buttress_reset_authentication(isp);
+	if (ret) {
+		dev_err(&isp->pdev->dev, "Failed to reset authentication!\n");
+		return ret;
+	}
+
+	ret = pm_runtime_get_sync(&isp->psys->dev);
+	if (ret < 0) {
+		dev_err(&isp->pdev->dev, "Runtime PM failed (%d)\n", ret);
+		return ret;
+	}
+
+	ret = ipu_buttress_authenticate(isp);
+	if (ret) {
+		dev_err(&isp->pdev->dev, "FW authentication failed\n");
+		return ret;
+	}
+
+	pm_runtime_put(&isp->psys->dev);
+
+	return 0;
+}
+EXPORT_SYMBOL(ipu_fw_authenticate);
+DEFINE_SIMPLE_ATTRIBUTE(authenticate_fops, NULL, ipu_fw_authenticate, "%llu\n");
+
+#ifdef CONFIG_DEBUG_FS
+static int resume_ipu_bus_device(struct ipu_bus_device *adev)
+{
+	struct device *dev = &adev->dev;
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+
+	if (!pm || !pm->resume)
+		return -EIO;
+
+	return pm->resume(dev);
+}
+
+static int suspend_ipu_bus_device(struct ipu_bus_device *adev)
+{
+	struct device *dev = &adev->dev;
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+
+	if (!pm || !pm->suspend)
+		return -EIO;
+
+	return pm->suspend(dev);
+}
+
+static int force_suspend_get(void *data, u64 *val)
+{
+	struct ipu_device *isp = data;
+	struct ipu_buttress *b = &isp->buttress;
+
+	*val = b->force_suspend;
+	return 0;
+}
+
+static int force_suspend_set(void *data, u64 val)
+{
+	struct ipu_device *isp = data;
+	struct ipu_buttress *b = &isp->buttress;
+	int ret = 0;
+
+	if (val == b->force_suspend)
+		return 0;
+
+	if (val) {
+		b->force_suspend = 1;
+		ret = suspend_ipu_bus_device(isp->psys);
+		if (ret) {
+			dev_err(&isp->pdev->dev, "Failed to suspend psys\n");
+			return ret;
+		}
+		ret = suspend_ipu_bus_device(isp->isys);
+		if (ret) {
+			dev_err(&isp->pdev->dev, "Failed to suspend isys\n");
+			return ret;
+		}
+		ret = pci_set_power_state(isp->pdev, PCI_D3hot);
+		if (ret) {
+			dev_err(&isp->pdev->dev,
+				"Failed to suspend IUnit PCI device\n");
+			return ret;
+		}
+	} else {
+		ret = pci_set_power_state(isp->pdev, PCI_D0);
+		if (ret) {
+			dev_err(&isp->pdev->dev,
+				"Failed to suspend IUnit PCI device\n");
+			return ret;
+		}
+		ret = resume_ipu_bus_device(isp->isys);
+		if (ret) {
+			dev_err(&isp->pdev->dev, "Failed to resume isys\n");
+			return ret;
+		}
+		ret = resume_ipu_bus_device(isp->psys);
+		if (ret) {
+			dev_err(&isp->pdev->dev, "Failed to resume psys\n");
+			return ret;
+		}
+		b->force_suspend = 0;
+	}
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(force_suspend_fops, force_suspend_get,
+			force_suspend_set, "%llu\n");
+/*
+ * The sysfs interface for reloading cpd fw is there only for debug purpose,
+ * and it must not be used when either isys or psys is in use.
+ */
+static int cpd_fw_reload(void *data, u64 val)
+{
+	struct ipu_device *isp = data;
+	int rval = -EINVAL;
+
+	if (isp->cpd_fw_reload)
+		rval = isp->cpd_fw_reload(isp);
+
+	return rval;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(cpd_fw_fops, NULL, cpd_fw_reload, "%llu\n");
+
+static int ipu_init_debugfs(struct ipu_device *isp)
+{
+	struct dentry *file;
+	struct dentry *dir;
+
+	dir = debugfs_create_dir(pci_name(isp->pdev), NULL);
+	if (!dir)
+		return -ENOMEM;
+
+	file = debugfs_create_file("force_suspend", 0700, dir, isp,
+				   &force_suspend_fops);
+	if (!file)
+		goto err;
+	file = debugfs_create_file("authenticate", 0700, dir, isp,
+				   &authenticate_fops);
+	if (!file)
+		goto err;
+
+	file = debugfs_create_file("cpd_fw_reload", 0700, dir, isp,
+				   &cpd_fw_fops);
+	if (!file)
+		goto err;
+
+	if (ipu_trace_debugfs_add(isp, dir))
+		goto err;
+
+	isp->ipu_dir = dir;
+
+	if (ipu_buttress_debugfs_init(isp))
+		goto err;
+
+	return 0;
+err:
+	debugfs_remove_recursive(dir);
+	return -ENOMEM;
+}
+
+static void ipu_remove_debugfs(struct ipu_device *isp)
+{
+	/*
+	 * Since isys and psys debugfs dir will be created under ipu root dir,
+	 * mark its dentry to NULL to avoid duplicate removal.
+	 */
+	debugfs_remove_recursive(isp->ipu_dir);
+	isp->ipu_dir = NULL;
+}
+#endif /* CONFIG_DEBUG_FS */
+
+static int ipu_pci_config_setup(struct pci_dev *dev)
+{
+	u16 pci_command;
+	int rval;
+
+	pci_read_config_word(dev, PCI_COMMAND, &pci_command);
+	pci_command |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
+	pci_write_config_word(dev, PCI_COMMAND, pci_command);
+	if (ipu_ver == IPU_VER_6EP) {
+		/* likely do nothing as msi not enabled by default */
+		pci_disable_msi(dev);
+		return 0;
+	}
+
+	rval = pci_enable_msi(dev);
+	if (rval)
+		dev_err(&dev->dev, "Failed to enable msi (%d)\n", rval);
+
+	return rval;
+}
+
+static void ipu_configure_vc_mechanism(struct ipu_device *isp)
+{
+	u32 val = readl(isp->base + BUTTRESS_REG_BTRS_CTRL);
+
+	if (IPU_BTRS_ARB_STALL_MODE_VC0 == IPU_BTRS_ARB_MODE_TYPE_STALL)
+		val |= BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC0;
+	else
+		val &= ~BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC0;
+
+	if (IPU_BTRS_ARB_STALL_MODE_VC1 == IPU_BTRS_ARB_MODE_TYPE_STALL)
+		val |= BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC1;
+	else
+		val &= ~BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC1;
+
+	writel(val, isp->base + BUTTRESS_REG_BTRS_CTRL);
+}
+
+int request_cpd_fw(const struct firmware **firmware_p, const char *name,
+		   struct device *device)
+{
+	const struct firmware *fw;
+	struct firmware *tmp;
+	int ret;
+
+	ret = request_firmware(&fw, name, device);
+	if (ret)
+		return ret;
+
+	if (is_vmalloc_addr(fw->data)) {
+		*firmware_p = fw;
+	} else {
+		tmp = kzalloc(sizeof(*tmp), GFP_KERNEL);
+		if (!tmp) {
+			release_firmware(fw);
+			return -ENOMEM;
+		}
+		tmp->size = fw->size;
+		tmp->data = vmalloc(fw->size);
+		if (!tmp->data) {
+			kfree(tmp);
+			release_firmware(fw);
+			return -ENOMEM;
+		}
+		memcpy((void *)tmp->data, fw->data, fw->size);
+		*firmware_p = tmp;
+		release_firmware(fw);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(request_cpd_fw);
+
+static int ipu_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct ipu_device *isp;
+	phys_addr_t phys;
+	void __iomem *const *iomap;
+	void __iomem *isys_base = NULL;
+	void __iomem *psys_base = NULL;
+	struct ipu_buttress_ctrl *isys_ctrl = NULL, *psys_ctrl = NULL;
+	unsigned int dma_mask = IPU_DMA_MASK;
+	struct fwnode_handle *fwnode = dev_fwnode(&pdev->dev);
+	u32 is_es;
+	int rval;
+
+	if (!fwnode || fwnode_property_read_u32(fwnode, "is_es", &is_es))
+		is_es = 0;
+
+	isp = devm_kzalloc(&pdev->dev, sizeof(*isp), GFP_KERNEL);
+	if (!isp)
+		return -ENOMEM;
+
+	dev_set_name(&pdev->dev, "intel-ipu");
+	isp->pdev = pdev;
+	INIT_LIST_HEAD(&isp->devices);
+
+	rval = pcim_enable_device(pdev);
+	if (rval) {
+		dev_err(&pdev->dev, "Failed to enable CI ISP device (%d)\n",
+			rval);
+		return rval;
+	}
+
+	dev_info(&pdev->dev, "Device 0x%x (rev: 0x%x)\n",
+		 pdev->device, pdev->revision);
+
+	phys = pci_resource_start(pdev, IPU_PCI_BAR);
+
+	rval = pcim_iomap_regions(pdev,
+				  1 << IPU_PCI_BAR,
+				  pci_name(pdev));
+	if (rval) {
+		dev_err(&pdev->dev, "Failed to I/O memory remapping (%d)\n",
+			rval);
+		return rval;
+	}
+	dev_info(&pdev->dev, "physical base address 0x%llx\n", phys);
+
+	iomap = pcim_iomap_table(pdev);
+	if (!iomap) {
+		dev_err(&pdev->dev, "Failed to iomap table (%d)\n", rval);
+		return -ENODEV;
+	}
+
+	isp->base = iomap[IPU_PCI_BAR];
+	dev_info(&pdev->dev, "mapped as: 0x%p\n", isp->base);
+
+	pci_set_drvdata(pdev, isp);
+	pci_set_master(pdev);
+
+	switch (id->device) {
+	case IPU6_PCI_ID:
+		ipu_ver = IPU_VER_6;
+		isp->cpd_fw_name = IPU6_FIRMWARE_NAME;
+		break;
+	case IPU6SE_PCI_ID:
+		ipu_ver = IPU_VER_6SE;
+		isp->cpd_fw_name = IPU6SE_FIRMWARE_NAME;
+		break;
+	case IPU6EP_ADL_P_PCI_ID:
+	case IPU6EP_ADL_N_PCI_ID:
+	case IPU6EP_RPL_P_PCI_ID:
+		ipu_ver = IPU_VER_6EP;
+		isp->cpd_fw_name = is_es ? IPU6EPES_FIRMWARE_NAME : IPU6EP_FIRMWARE_NAME;
+		break;
+	default:
+		WARN(1, "Unsupported IPU device");
+		return -ENODEV;
+	}
+
+	ipu_internal_pdata_init();
+
+	isys_base = isp->base + isys_ipdata.hw_variant.offset;
+	psys_base = isp->base + psys_ipdata.hw_variant.offset;
+
+	dev_dbg(&pdev->dev, "isys_base: 0x%lx\n", (unsigned long)isys_base);
+	dev_dbg(&pdev->dev, "psys_base: 0x%lx\n", (unsigned long)psys_base);
+
+	rval = pci_set_dma_mask(pdev, DMA_BIT_MASK(dma_mask));
+	if (!rval)
+		rval = pci_set_consistent_dma_mask(pdev,
+						   DMA_BIT_MASK(dma_mask));
+	if (rval) {
+		dev_err(&pdev->dev, "Failed to set DMA mask (%d)\n", rval);
+		return rval;
+	}
+
+	dma_set_max_seg_size(&pdev->dev, UINT_MAX);
+
+	rval = ipu_pci_config_setup(pdev);
+	if (rval)
+		return rval;
+
+	rval = devm_request_threaded_irq(&pdev->dev, pdev->irq,
+					 ipu_buttress_isr,
+					 ipu_buttress_isr_threaded,
+					 IRQF_SHARED, IPU_NAME, isp);
+	if (rval) {
+		dev_err(&pdev->dev, "Requesting irq failed(%d)\n", rval);
+		return rval;
+	}
+
+	rval = ipu_buttress_init(isp);
+	if (rval)
+		return rval;
+
+	dev_info(&pdev->dev, "cpd file name: %s\n", isp->cpd_fw_name);
+
+	rval = request_cpd_fw(&isp->cpd_fw, isp->cpd_fw_name, &pdev->dev);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Requesting signed firmware failed\n");
+		return rval;
+	}
+
+	rval = ipu_cpd_validate_cpd_file(isp, isp->cpd_fw->data,
+					 isp->cpd_fw->size);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Failed to validate cpd\n");
+		goto out_ipu_bus_del_devices;
+	}
+
+	rval = ipu_trace_add(isp);
+	if (rval)
+		dev_err(&pdev->dev, "Trace support not available\n");
+
+	pm_runtime_put_noidle(&pdev->dev);
+	pm_runtime_allow(&pdev->dev);
+
+	/*
+	 * NOTE Device hierarchy below is important to ensure proper
+	 * runtime suspend and resume order.
+	 * Also registration order is important to ensure proper
+	 * suspend and resume order during system
+	 * suspend. Registration order is as follows:
+	 * isys->psys
+	 */
+	isys_ctrl = devm_kzalloc(&pdev->dev, sizeof(*isys_ctrl), GFP_KERNEL);
+	if (!isys_ctrl) {
+		rval = -ENOMEM;
+		goto out_ipu_bus_del_devices;
+	}
+
+	/* Init butress control with default values based on the HW */
+	memcpy(isys_ctrl, &isys_buttress_ctrl, sizeof(*isys_ctrl));
+
+	isp->isys = ipu_isys_init(pdev, &pdev->dev,
+				  isys_ctrl, isys_base,
+				  &isys_ipdata,
+				  0);
+	if (IS_ERR(isp->isys)) {
+		rval = PTR_ERR(isp->isys);
+		goto out_ipu_bus_del_devices;
+	}
+
+	psys_ctrl = devm_kzalloc(&pdev->dev, sizeof(*psys_ctrl), GFP_KERNEL);
+	if (!psys_ctrl) {
+		rval = -ENOMEM;
+		goto out_ipu_bus_del_devices;
+	}
+
+	/* Init butress control with default values based on the HW */
+	memcpy(psys_ctrl, &psys_buttress_ctrl, sizeof(*psys_ctrl));
+
+	isp->psys = ipu_psys_init(pdev, &isp->isys->dev,
+				  psys_ctrl, psys_base,
+				  &psys_ipdata, 0);
+	if (IS_ERR(isp->psys)) {
+		rval = PTR_ERR(isp->psys);
+		goto out_ipu_bus_del_devices;
+	}
+
+	rval = pm_runtime_get_sync(&isp->psys->dev);
+	if (rval < 0) {
+		dev_err(&isp->psys->dev, "Failed to get runtime PM\n");
+		goto out_ipu_bus_del_devices;
+	}
+
+	rval = ipu_mmu_hw_init(isp->psys->mmu);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "Failed to set mmu hw\n");
+		goto out_ipu_bus_del_devices;
+	}
+
+	rval = ipu_buttress_map_fw_image(isp->psys, isp->cpd_fw,
+					 &isp->fw_sgt);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "failed to map fw image\n");
+		goto out_ipu_bus_del_devices;
+	}
+
+	isp->pkg_dir = ipu_cpd_create_pkg_dir(isp->psys,
+					      isp->cpd_fw->data,
+					      sg_dma_address(isp->fw_sgt.sgl),
+					      &isp->pkg_dir_dma_addr,
+					      &isp->pkg_dir_size);
+	if (!isp->pkg_dir) {
+		rval = -ENOMEM;
+		dev_err(&isp->pdev->dev, "failed to create pkg dir\n");
+		goto out_ipu_bus_del_devices;
+	}
+
+	rval = ipu_buttress_authenticate(isp);
+	if (rval) {
+		dev_err(&isp->pdev->dev, "FW authentication failed(%d)\n",
+			rval);
+		goto out_ipu_bus_del_devices;
+	}
+
+	ipu_mmu_hw_cleanup(isp->psys->mmu);
+	pm_runtime_put(&isp->psys->dev);
+
+#ifdef CONFIG_DEBUG_FS
+	rval = ipu_init_debugfs(isp);
+	if (rval) {
+		dev_err(&pdev->dev, "Failed to initialize debugfs");
+		goto out_ipu_bus_del_devices;
+	}
+#endif
+
+	/* Configure the arbitration mechanisms for VC requests */
+	ipu_configure_vc_mechanism(isp);
+
+	dev_info(&pdev->dev, "IPU driver version %d.%d\n", IPU_MAJOR_VERSION,
+		 IPU_MINOR_VERSION);
+
+	return 0;
+
+out_ipu_bus_del_devices:
+	if (isp->pkg_dir) {
+		ipu_cpd_free_pkg_dir(isp->psys, isp->pkg_dir,
+				     isp->pkg_dir_dma_addr,
+				     isp->pkg_dir_size);
+		ipu_buttress_unmap_fw_image(isp->psys, &isp->fw_sgt);
+		isp->pkg_dir = NULL;
+	}
+	if (isp->psys && isp->psys->mmu)
+		ipu_mmu_cleanup(isp->psys->mmu);
+	if (isp->isys && isp->isys->mmu)
+		ipu_mmu_cleanup(isp->isys->mmu);
+	if (isp->psys)
+		pm_runtime_put(&isp->psys->dev);
+	ipu_bus_del_devices(pdev);
+	ipu_buttress_exit(isp);
+	release_firmware(isp->cpd_fw);
+
+	return rval;
+}
+
+static void ipu_pci_remove(struct pci_dev *pdev)
+{
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+
+#ifdef CONFIG_DEBUG_FS
+	ipu_remove_debugfs(isp);
+#endif
+	ipu_trace_release(isp);
+
+	ipu_cpd_free_pkg_dir(isp->psys, isp->pkg_dir, isp->pkg_dir_dma_addr,
+			     isp->pkg_dir_size);
+
+	ipu_buttress_unmap_fw_image(isp->psys, &isp->fw_sgt);
+
+	isp->pkg_dir = NULL;
+	isp->pkg_dir_dma_addr = 0;
+	isp->pkg_dir_size = 0;
+
+	ipu_bus_del_devices(pdev);
+
+	pm_runtime_forbid(&pdev->dev);
+	pm_runtime_get_noresume(&pdev->dev);
+
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+
+	ipu_buttress_exit(isp);
+
+	release_firmware(isp->cpd_fw);
+
+	ipu_mmu_cleanup(isp->psys->mmu);
+	ipu_mmu_cleanup(isp->isys->mmu);
+}
+
+static void ipu_pci_reset_prepare(struct pci_dev *pdev)
+{
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+
+	dev_warn(&pdev->dev, "FLR prepare\n");
+	pm_runtime_forbid(&isp->pdev->dev);
+	isp->flr_done = true;
+}
+
+static void ipu_pci_reset_done(struct pci_dev *pdev)
+{
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+
+	ipu_buttress_restore(isp);
+	if (isp->secure_mode)
+		ipu_buttress_reset_authentication(isp);
+
+	ipu_bus_flr_recovery();
+	isp->ipc_reinit = true;
+	pm_runtime_allow(&isp->pdev->dev);
+
+	dev_warn(&pdev->dev, "FLR completed\n");
+}
+
+#ifdef CONFIG_PM
+
+/*
+ * PCI base driver code requires driver to provide these to enable
+ * PCI device level PM state transitions (D0<->D3)
+ */
+static int ipu_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+
+	isp->flr_done = false;
+
+	return 0;
+}
+
+static int ipu_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+	struct ipu_buttress *b = &isp->buttress;
+	int rval;
+
+	/* Configure the arbitration mechanisms for VC requests */
+	ipu_configure_vc_mechanism(isp);
+
+	ipu_buttress_set_secure_mode(isp);
+	isp->secure_mode = ipu_buttress_get_secure_mode(isp);
+	dev_info(dev, "IPU in %s mode\n",
+		 isp->secure_mode ? "secure" : "non-secure");
+
+	ipu_buttress_restore(isp);
+
+	rval = ipu_buttress_ipc_reset(isp, &b->cse);
+	if (rval)
+		dev_err(&isp->pdev->dev, "IPC reset protocol failed!\n");
+
+	rval = pm_runtime_get_sync(&isp->psys->dev);
+	if (rval < 0) {
+		dev_err(&isp->psys->dev, "Failed to get runtime PM\n");
+		return 0;
+	}
+
+	rval = ipu_buttress_authenticate(isp);
+	if (rval)
+		dev_err(&isp->pdev->dev, "FW authentication failed(%d)\n",
+			rval);
+
+	pm_runtime_put(&isp->psys->dev);
+
+	return 0;
+}
+
+static int ipu_runtime_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct ipu_device *isp = pci_get_drvdata(pdev);
+	int rval;
+
+	ipu_configure_vc_mechanism(isp);
+	ipu_buttress_restore(isp);
+
+	if (isp->ipc_reinit) {
+		struct ipu_buttress *b = &isp->buttress;
+
+		isp->ipc_reinit = false;
+		rval = ipu_buttress_ipc_reset(isp, &b->cse);
+		if (rval)
+			dev_err(&isp->pdev->dev,
+				"IPC reset protocol failed!\n");
+	}
+
+	return 0;
+}
+
+static const struct dev_pm_ops ipu_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(&ipu_suspend, &ipu_resume)
+	    SET_RUNTIME_PM_OPS(&ipu_suspend,	/* Same as in suspend flow */
+			       &ipu_runtime_resume,
+			       NULL)
+};
+
+#define IPU_PM (&ipu_pm_ops)
+#else
+#define IPU_PM NULL
+#endif
+
+static const struct pci_device_id ipu_pci_tbl[] = {
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6SE_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_ADL_P_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_ADL_N_PCI_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, IPU6EP_RPL_P_PCI_ID)},
+	{0,}
+};
+MODULE_DEVICE_TABLE(pci, ipu_pci_tbl);
+
+static const struct pci_error_handlers pci_err_handlers = {
+	.reset_prepare = ipu_pci_reset_prepare,
+	.reset_done = ipu_pci_reset_done,
+};
+
+static struct pci_driver ipu_pci_driver = {
+	.name = IPU_NAME,
+	.id_table = ipu_pci_tbl,
+	.probe = ipu_pci_probe,
+	.remove = ipu_pci_remove,
+	.driver = {
+		   .pm = IPU_PM,
+		   },
+	.err_handler = &pci_err_handlers,
+};
+
+static int __init ipu_init(void)
+{
+	int rval = ipu_bus_register();
+
+	if (rval) {
+		pr_warn("can't register ipu bus (%d)\n", rval);
+		return rval;
+	}
+
+	rval = pci_register_driver(&ipu_pci_driver);
+	if (rval) {
+		pr_warn("can't register pci driver (%d)\n", rval);
+		goto out_pci_register_driver;
+	}
+
+	return 0;
+
+out_pci_register_driver:
+	ipu_bus_unregister();
+
+	return rval;
+}
+
+static void __exit ipu_exit(void)
+{
+	pci_unregister_driver(&ipu_pci_driver);
+	ipu_bus_unregister();
+}
+
+module_init(ipu_init);
+module_exit(ipu_exit);
+
+MODULE_AUTHOR("Sakari Ailus <sakari.ailus@linux.intel.com>");
+MODULE_AUTHOR("Jouni Högander <jouni.hogander@intel.com>");
+MODULE_AUTHOR("Antti Laakso <antti.laakso@intel.com>");
+MODULE_AUTHOR("Samu Onkalo <samu.onkalo@intel.com>");
+MODULE_AUTHOR("Jianxu Zheng <jian.xu.zheng@intel.com>");
+MODULE_AUTHOR("Tianshu Qiu <tian.shu.qiu@intel.com>");
+MODULE_AUTHOR("Renwei Wu <renwei.wu@intel.com>");
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_AUTHOR("Yunliang Ding <yunliang.ding@intel.com>");
+MODULE_AUTHOR("Zaikuo Wang <zaikuo.wang@intel.com>");
+MODULE_AUTHOR("Leifu Zhao <leifu.zhao@intel.com>");
+MODULE_AUTHOR("Xia Wu <xia.wu@intel.com>");
+MODULE_AUTHOR("Kun Jiang <kun.jiang@intel.com>");
+MODULE_AUTHOR("Intel");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel ipu pci driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu.h
@@ -0,0 +1,111 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_H
+#define IPU_H
+
+#include <linux/ioport.h>
+#include <linux/list.h>
+#include <uapi/linux/media.h>
+#include <linux/version.h>
+
+#include "ipu-pdata.h"
+#include "ipu-bus.h"
+#include "ipu-buttress.h"
+#include "ipu-trace.h"
+
+#define IPU6_PCI_ID	0x9a19
+#define IPU6SE_PCI_ID	0x4e19
+#define IPU6EP_ADL_P_PCI_ID	0x465d
+#define IPU6EP_ADL_N_PCI_ID	0x462e
+#define IPU6EP_RPL_P_PCI_ID	0xa75d
+#define IPU6EP_MTL_PCI_ID	0x7d19
+
+enum ipu_version {
+	IPU_VER_INVALID = 0,
+	IPU_VER_6,
+	IPU_VER_6SE,
+	IPU_VER_6EP,
+};
+
+/*
+ * IPU version definitions to reflect the IPU driver changes.
+ * Both ISYS and PSYS share the same version.
+ */
+#define IPU_MAJOR_VERSION 1
+#define IPU_MINOR_VERSION 0
+#define IPU_DRIVER_VERSION (IPU_MAJOR_VERSION << 16 | IPU_MINOR_VERSION)
+
+/* processing system frequency: 25Mhz x ratio, Legal values [8,32] */
+#define PS_FREQ_CTL_DEFAULT_RATIO	0x12
+
+/* input system frequency: 1600Mhz / divisor. Legal values [2,8] */
+#define IS_FREQ_SOURCE			1600000000
+#define IS_FREQ_CTL_DIVISOR		0x4
+
+/*
+ * ISYS DMA can overshoot. For higher resolutions over allocation is one line
+ * but it must be at minimum 1024 bytes. Value could be different in
+ * different versions / generations thus provide it via platform data.
+ */
+#define IPU_ISYS_OVERALLOC_MIN		1024
+
+/*
+ * Physical pages in GDA is 128, page size is 2K for IPU6, 1K for others.
+ */
+#define IPU_DEVICE_GDA_NR_PAGES		128
+
+/*
+ * Virtualization factor to calculate the available virtual pages.
+ */
+#define IPU_DEVICE_GDA_VIRT_FACTOR	32
+
+struct pci_dev;
+struct list_head;
+struct firmware;
+
+#define NR_OF_MMU_RESOURCES			2
+
+struct ipu_device {
+	struct pci_dev *pdev;
+	struct list_head devices;
+	struct ipu_bus_device *isys;
+	struct ipu_bus_device *psys;
+	struct ipu_buttress buttress;
+
+	const struct firmware *cpd_fw;
+	const char *cpd_fw_name;
+	u64 *pkg_dir;
+	dma_addr_t pkg_dir_dma_addr;
+	unsigned int pkg_dir_size;
+	struct sg_table fw_sgt;
+
+	void __iomem *base;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry *ipu_dir;
+#endif
+	struct ipu_trace *trace;
+	bool flr_done;
+	bool ipc_reinit;
+	bool secure_mode;
+
+	int (*cpd_fw_reload)(struct ipu_device *isp);
+};
+
+#define IPU_DMA_MASK	39
+#define IPU_LIB_CALL_TIMEOUT_MS		2000
+#define IPU_PSYS_CMD_TIMEOUT_MS	2000
+#define IPU_PSYS_OPEN_TIMEOUT_US	   50
+#define IPU_PSYS_OPEN_RETRY (10000 / IPU_PSYS_OPEN_TIMEOUT_US)
+
+int ipu_fw_authenticate(void *data, u64 val);
+void ipu_configure_spc(struct ipu_device *isp,
+		       const struct ipu_hw_variants *hw_variant,
+		       int pkg_dir_idx, void __iomem *base, u64 *pkg_dir,
+		       dma_addr_t pkg_dir_dma_addr);
+int request_cpd_fw(const struct firmware **firmware_p, const char *name,
+		   struct device *device);
+extern enum ipu_version ipu_ver;
+void ipu_internal_pdata_init(void);
+
+#endif /* IPU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu3/ipu3-cio2-main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu3/ipu3-cio2-main.c
@@ -102,26 +102,29 @@
 
 static void cio2_fbpt_exit_dummy(struct cio2_device *cio2)
 {
+	struct device *dev = &cio2->pci_dev->dev;
+
 	if (cio2->dummy_lop) {
-		dma_free_coherent(&cio2->pci_dev->dev, PAGE_SIZE,
-				  cio2->dummy_lop, cio2->dummy_lop_bus_addr);
+		dma_free_coherent(dev, PAGE_SIZE, cio2->dummy_lop,
+				  cio2->dummy_lop_bus_addr);
 		cio2->dummy_lop = NULL;
 	}
 	if (cio2->dummy_page) {
-		dma_free_coherent(&cio2->pci_dev->dev, PAGE_SIZE,
-				  cio2->dummy_page, cio2->dummy_page_bus_addr);
+		dma_free_coherent(dev, PAGE_SIZE, cio2->dummy_page,
+				  cio2->dummy_page_bus_addr);
 		cio2->dummy_page = NULL;
 	}
 }
 
 static int cio2_fbpt_init_dummy(struct cio2_device *cio2)
 {
+	struct device *dev = &cio2->pci_dev->dev;
 	unsigned int i;
 
-	cio2->dummy_page = dma_alloc_coherent(&cio2->pci_dev->dev, PAGE_SIZE,
+	cio2->dummy_page = dma_alloc_coherent(dev, PAGE_SIZE,
 					      &cio2->dummy_page_bus_addr,
 					      GFP_KERNEL);
-	cio2->dummy_lop = dma_alloc_coherent(&cio2->pci_dev->dev, PAGE_SIZE,
+	cio2->dummy_lop = dma_alloc_coherent(dev, PAGE_SIZE,
 					     &cio2->dummy_lop_bus_addr,
 					     GFP_KERNEL);
 	if (!cio2->dummy_page || !cio2->dummy_lop) {
@@ -345,7 +348,7 @@
 	void __iomem *const base = cio2->base;
 	u8 lanes, csi2bus = q->csi2.port;
 	u8 sensor_vc = SENSOR_VIR_CH_DFLT;
-	struct cio2_csi2_timing timing;
+	struct cio2_csi2_timing timing = { 0 };
 	int i, r;
 
 	fmt = cio2_find_format(NULL, &q->subdev_fmt.code);
@@ -497,6 +500,7 @@
 
 static void cio2_hw_exit(struct cio2_device *cio2, struct cio2_queue *q)
 {
+	struct device *dev = &cio2->pci_dev->dev;
 	void __iomem *const base = cio2->base;
 	unsigned int i;
 	u32 value;
@@ -514,8 +518,7 @@
 				 value, value & CIO2_CDMAC0_DMA_HALTED,
 				 4000, 2000000);
 	if (ret)
-		dev_err(&cio2->pci_dev->dev,
-			"DMA %i can not be halted\n", CIO2_DMA_CHAN);
+		dev_err(dev, "DMA %i can not be halted\n", CIO2_DMA_CHAN);
 
 	for (i = 0; i < CIO2_NUM_PORTS; i++) {
 		writel(readl(base + CIO2_REG_PXM_FRF_CFG(i)) |
@@ -539,8 +542,7 @@
 
 	entry = &q->fbpt[q->bufs_first * CIO2_MAX_LOPS];
 	if (entry->first_entry.ctrl & CIO2_FBPT_CTRL_VALID) {
-		dev_warn(&cio2->pci_dev->dev,
-			 "no ready buffers found on DMA channel %u\n",
+		dev_warn(dev, "no ready buffers found on DMA channel %u\n",
 			 dma_chan);
 		return;
 	}
@@ -557,8 +559,7 @@
 
 			q->bufs[q->bufs_first] = NULL;
 			atomic_dec(&q->bufs_queued);
-			dev_dbg(&cio2->pci_dev->dev,
-				"buffer %i done\n", b->vbb.vb2_buf.index);
+			dev_dbg(dev, "buffer %i done\n", b->vbb.vb2_buf.index);
 
 			b->vbb.vb2_buf.timestamp = ns;
 			b->vbb.field = V4L2_FIELD_NONE;
@@ -624,8 +625,8 @@
 
 static void cio2_irq_handle_once(struct cio2_device *cio2, u32 int_status)
 {
-	void __iomem *const base = cio2->base;
 	struct device *dev = &cio2->pci_dev->dev;
+	void __iomem *const base = cio2->base;
 
 	if (int_status & CIO2_INT_IOOE) {
 		/*
@@ -795,6 +796,7 @@
 				struct device *alloc_devs[])
 {
 	struct cio2_device *cio2 = vb2_get_drv_priv(vq);
+	struct device *dev = &cio2->pci_dev->dev;
 	struct cio2_queue *q = vb2q_to_cio2_queue(vq);
 	unsigned int i;
 
@@ -802,7 +804,7 @@
 
 	for (i = 0; i < *num_planes; ++i) {
 		sizes[i] = q->format.plane_fmt[i].sizeimage;
-		alloc_devs[i] = &cio2->pci_dev->dev;
+		alloc_devs[i] = dev;
 	}
 
 	*num_buffers = clamp_val(*num_buffers, 1, CIO2_MAX_BUFFERS);
@@ -879,6 +881,7 @@
 static void cio2_vb2_buf_queue(struct vb2_buffer *vb)
 {
 	struct cio2_device *cio2 = vb2_get_drv_priv(vb->vb2_queue);
+	struct device *dev = &cio2->pci_dev->dev;
 	struct cio2_queue *q =
 		container_of(vb->vb2_queue, struct cio2_queue, vbq);
 	struct cio2_buffer *b =
@@ -889,7 +892,7 @@
 	int bufs_queued = atomic_inc_return(&q->bufs_queued);
 	u32 fbpt_rp;
 
-	dev_dbg(&cio2->pci_dev->dev, "queue buffer %d\n", vb->index);
+	dev_dbg(dev, "queue buffer %d\n", vb->index);
 
 	/*
 	 * This code queues the buffer to the CIO2 DMA engine, which starts
@@ -940,12 +943,12 @@
 			return;
 		}
 
-		dev_dbg(&cio2->pci_dev->dev, "entry %i was full!\n", next);
+		dev_dbg(dev, "entry %i was full!\n", next);
 		next = (next + 1) % CIO2_MAX_BUFFERS;
 	}
 
 	local_irq_restore(flags);
-	dev_err(&cio2->pci_dev->dev, "error: all cio2 entries were full!\n");
+	dev_err(dev, "error: all cio2 entries were full!\n");
 	atomic_dec(&q->bufs_queued);
 	vb2_buffer_done(vb, VB2_BUF_STATE_ERROR);
 }
@@ -954,6 +957,7 @@
 static void cio2_vb2_buf_cleanup(struct vb2_buffer *vb)
 {
 	struct cio2_device *cio2 = vb2_get_drv_priv(vb->vb2_queue);
+	struct device *dev = &cio2->pci_dev->dev;
 	struct cio2_buffer *b =
 		container_of(vb, struct cio2_buffer, vbb.vb2_buf);
 	unsigned int i;
@@ -961,7 +965,7 @@
 	/* Free LOP table */
 	for (i = 0; i < CIO2_MAX_LOPS; i++) {
 		if (b->lop[i])
-			dma_free_coherent(&cio2->pci_dev->dev, PAGE_SIZE,
+			dma_free_coherent(dev, PAGE_SIZE,
 					  b->lop[i], b->lop_bus_addr[i]);
 	}
 }
@@ -970,14 +974,15 @@
 {
 	struct cio2_queue *q = vb2q_to_cio2_queue(vq);
 	struct cio2_device *cio2 = vb2_get_drv_priv(vq);
+	struct device *dev = &cio2->pci_dev->dev;
 	int r;
 
 	cio2->cur_queue = q;
 	atomic_set(&q->frame_sequence, 0);
 
-	r = pm_runtime_resume_and_get(&cio2->pci_dev->dev);
+	r = pm_runtime_resume_and_get(dev);
 	if (r < 0) {
-		dev_info(&cio2->pci_dev->dev, "failed to set power %d\n", r);
+		dev_info(dev, "failed to set power %d\n", r);
 		return r;
 	}
 
@@ -1003,9 +1008,9 @@
 fail_hw:
 	media_pipeline_stop(&q->vdev.entity);
 fail_pipeline:
-	dev_dbg(&cio2->pci_dev->dev, "failed to start streaming (%d)\n", r);
+	dev_dbg(dev, "failed to start streaming (%d)\n", r);
 	cio2_vb2_return_all_buffers(q, VB2_BUF_STATE_QUEUED);
-	pm_runtime_put(&cio2->pci_dev->dev);
+	pm_runtime_put(dev);
 
 	return r;
 }
@@ -1014,16 +1019,16 @@
 {
 	struct cio2_queue *q = vb2q_to_cio2_queue(vq);
 	struct cio2_device *cio2 = vb2_get_drv_priv(vq);
+	struct device *dev = &cio2->pci_dev->dev;
 
 	if (v4l2_subdev_call(q->sensor, video, s_stream, 0))
-		dev_err(&cio2->pci_dev->dev,
-			"failed to stop sensor streaming\n");
+		dev_err(dev, "failed to stop sensor streaming\n");
 
 	cio2_hw_exit(cio2, q);
 	synchronize_irq(cio2->pci_dev->irq);
 	cio2_vb2_return_all_buffers(q, VB2_BUF_STATE_ERROR);
 	media_pipeline_stop(&q->vdev.entity);
-	pm_runtime_put(&cio2->pci_dev->dev);
+	pm_runtime_put(dev);
 	cio2->streaming = false;
 }
 
@@ -1315,12 +1320,12 @@
 						struct video_device, entity);
 	struct cio2_queue *q = container_of(vd, struct cio2_queue, vdev);
 	struct cio2_device *cio2 = video_get_drvdata(vd);
+	struct device *dev = &cio2->pci_dev->dev;
 	struct v4l2_subdev_format source_fmt;
 	int ret;
 
 	if (!media_entity_remote_pad(link->sink->entity->pads)) {
-		dev_info(&cio2->pci_dev->dev,
-			 "video node %s pad not connected\n", vd->name);
+		dev_info(dev, "video node %s pad not connected\n", vd->name);
 		return -ENOTCONN;
 	}
 
@@ -1330,8 +1335,7 @@
 
 	if (source_fmt.format.width != q->format.width ||
 	    source_fmt.format.height != q->format.height) {
-		dev_err(&cio2->pci_dev->dev,
-			"Wrong width or height %ux%u (%ux%u expected)\n",
+		dev_err(dev, "Wrong width or height %ux%u (%ux%u expected)\n",
 			q->format.width, q->format.height,
 			source_fmt.format.width, source_fmt.format.height);
 		return -EINVAL;
@@ -1412,6 +1416,7 @@
 {
 	struct cio2_device *cio2 = container_of(notifier, struct cio2_device,
 						notifier);
+	struct device *dev = &cio2->pci_dev->dev;
 	struct sensor_async_subdev *s_asd;
 	struct v4l2_async_subdev *asd;
 	struct cio2_queue *q;
@@ -1428,8 +1433,7 @@
 				break;
 
 		if (pad == q->sensor->entity.num_pads) {
-			dev_err(&cio2->pci_dev->dev,
-				"failed to find src pad for %s\n",
+			dev_err(dev, "failed to find src pad for %s\n",
 				q->sensor->name);
 			return -ENXIO;
 		}
@@ -1439,8 +1443,7 @@
 				&q->subdev.entity, CIO2_PAD_SINK,
 				0);
 		if (ret) {
-			dev_err(&cio2->pci_dev->dev,
-				"failed to create link for %s\n",
+			dev_err(dev, "failed to create link for %s\n",
 				q->sensor->name);
 			return ret;
 		}
@@ -1457,6 +1460,7 @@
 
 static int cio2_parse_firmware(struct cio2_device *cio2)
 {
+	struct device *dev = &cio2->pci_dev->dev;
 	unsigned int i;
 	int ret;
 
@@ -1467,10 +1471,8 @@
 		struct sensor_async_subdev *s_asd;
 		struct fwnode_handle *ep;
 
-		ep = fwnode_graph_get_endpoint_by_id(
-			dev_fwnode(&cio2->pci_dev->dev), i, 0,
-			FWNODE_GRAPH_ENDPOINT_NEXT);
-
+		ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), i, 0,
+						FWNODE_GRAPH_ENDPOINT_NEXT);
 		if (!ep)
 			continue;
 
@@ -1504,8 +1506,7 @@
 	cio2->notifier.ops = &cio2_async_ops;
 	ret = v4l2_async_notifier_register(&cio2->v4l2_dev, &cio2->notifier);
 	if (ret)
-		dev_err(&cio2->pci_dev->dev,
-			"failed to register async notifier : %d\n", ret);
+		dev_err(dev, "failed to register async notifier : %d\n", ret);
 
 	return ret;
 }
@@ -1524,7 +1525,7 @@
 	static const u32 default_width = 1936;
 	static const u32 default_height = 1096;
 	const struct ipu3_cio2_fmt dflt_fmt = formats[0];
-
+	struct device *dev = &cio2->pci_dev->dev;
 	struct video_device *vdev = &q->vdev;
 	struct vb2_queue *vbq = &q->vbq;
 	struct v4l2_subdev *subdev = &q->subdev;
@@ -1566,8 +1567,7 @@
 	subdev->internal_ops = &cio2_subdev_internal_ops;
 	r = media_entity_pads_init(&subdev->entity, CIO2_PADS, q->subdev_pads);
 	if (r) {
-		dev_err(&cio2->pci_dev->dev,
-			"failed initialize subdev media entity (%d)\n", r);
+		dev_err(dev, "failed initialize subdev media entity (%d)\n", r);
 		goto fail_subdev_media_entity;
 	}
 
@@ -1575,8 +1575,8 @@
 	vdev->entity.ops = &cio2_video_entity_ops;
 	r = media_entity_pads_init(&vdev->entity, 1, &q->vdev_pad);
 	if (r) {
-		dev_err(&cio2->pci_dev->dev,
-			"failed initialize videodev media entity (%d)\n", r);
+		dev_err(dev, "failed initialize videodev media entity (%d)\n",
+			r);
 		goto fail_vdev_media_entity;
 	}
 
@@ -1590,8 +1590,7 @@
 	v4l2_set_subdevdata(subdev, cio2);
 	r = v4l2_device_register_subdev(&cio2->v4l2_dev, subdev);
 	if (r) {
-		dev_err(&cio2->pci_dev->dev,
-			"failed initialize subdev (%d)\n", r);
+		dev_err(dev, "failed initialize subdev (%d)\n", r);
 		goto fail_subdev;
 	}
 
@@ -1607,8 +1606,7 @@
 	vbq->lock = &q->lock;
 	r = vb2_queue_init(vbq);
 	if (r) {
-		dev_err(&cio2->pci_dev->dev,
-			"failed to initialize videobuf2 queue (%d)\n", r);
+		dev_err(dev, "failed to initialize videobuf2 queue (%d)\n", r);
 		goto fail_subdev;
 	}
 
@@ -1625,8 +1623,7 @@
 	video_set_drvdata(vdev, cio2);
 	r = video_register_device(vdev, VFL_TYPE_VIDEO, -1);
 	if (r) {
-		dev_err(&cio2->pci_dev->dev,
-			"failed to register video device (%d)\n", r);
+		dev_err(dev, "failed to register video device (%d)\n", r);
 		goto fail_vdev;
 	}
 
@@ -1648,7 +1645,7 @@
 fail_vdev_media_entity:
 	media_entity_cleanup(&subdev->entity);
 fail_subdev_media_entity:
-	cio2_fbpt_exit(q, &cio2->pci_dev->dev);
+	cio2_fbpt_exit(q, dev);
 fail_fbpt:
 	mutex_destroy(&q->subdev_lock);
 	mutex_destroy(&q->lock);
@@ -1715,11 +1712,12 @@
 static int cio2_pci_probe(struct pci_dev *pci_dev,
 			  const struct pci_device_id *id)
 {
-	struct fwnode_handle *fwnode = dev_fwnode(&pci_dev->dev);
+	struct device *dev = &pci_dev->dev;
+	struct fwnode_handle *fwnode = dev_fwnode(dev);
 	struct cio2_device *cio2;
 	int r;
 
-	cio2 = devm_kzalloc(&pci_dev->dev, sizeof(*cio2), GFP_KERNEL);
+	cio2 = devm_kzalloc(dev, sizeof(*cio2), GFP_KERNEL);
 	if (!cio2)
 		return -ENOMEM;
 	cio2->pci_dev = pci_dev;
@@ -1732,7 +1730,7 @@
 	r = cio2_check_fwnode_graph(fwnode);
 	if (r) {
 		if (fwnode && !IS_ERR_OR_NULL(fwnode->secondary)) {
-			dev_err(&pci_dev->dev, "fwnode graph has no endpoints connected\n");
+			dev_err(dev, "fwnode graph has no endpoints connected\n");
 			return -EINVAL;
 		}
 
@@ -1743,16 +1741,16 @@
 
 	r = pcim_enable_device(pci_dev);
 	if (r) {
-		dev_err(&pci_dev->dev, "failed to enable device (%d)\n", r);
+		dev_err(dev, "failed to enable device (%d)\n", r);
 		return r;
 	}
 
-	dev_info(&pci_dev->dev, "device 0x%x (rev: 0x%x)\n",
+	dev_info(dev, "device 0x%x (rev: 0x%x)\n",
 		 pci_dev->device, pci_dev->revision);
 
 	r = pcim_iomap_regions(pci_dev, 1 << CIO2_PCI_BAR, pci_name(pci_dev));
 	if (r) {
-		dev_err(&pci_dev->dev, "failed to remap I/O memory (%d)\n", r);
+		dev_err(dev, "failed to remap I/O memory (%d)\n", r);
 		return -ENODEV;
 	}
 
@@ -1764,13 +1762,13 @@
 
 	r = pci_set_dma_mask(pci_dev, CIO2_DMA_MASK);
 	if (r) {
-		dev_err(&pci_dev->dev, "failed to set DMA mask (%d)\n", r);
+		dev_err(dev, "failed to set DMA mask (%d)\n", r);
 		return -ENODEV;
 	}
 
 	r = pci_enable_msi(pci_dev);
 	if (r) {
-		dev_err(&pci_dev->dev, "failed to enable MSI (%d)\n", r);
+		dev_err(dev, "failed to enable MSI (%d)\n", r);
 		return r;
 	}
 
@@ -1780,7 +1778,7 @@
 
 	mutex_init(&cio2->lock);
 
-	cio2->media_dev.dev = &cio2->pci_dev->dev;
+	cio2->media_dev.dev = dev;
 	strscpy(cio2->media_dev.model, CIO2_DEVICE_NAME,
 		sizeof(cio2->media_dev.model));
 	snprintf(cio2->media_dev.bus_info, sizeof(cio2->media_dev.bus_info),
@@ -1793,10 +1791,9 @@
 		goto fail_mutex_destroy;
 
 	cio2->v4l2_dev.mdev = &cio2->media_dev;
-	r = v4l2_device_register(&pci_dev->dev, &cio2->v4l2_dev);
+	r = v4l2_device_register(dev, &cio2->v4l2_dev);
 	if (r) {
-		dev_err(&pci_dev->dev,
-			"failed to register V4L2 device (%d)\n", r);
+		dev_err(dev, "failed to register V4L2 device (%d)\n", r);
 		goto fail_media_device_unregister;
 	}
 
@@ -1806,20 +1803,20 @@
 
 	v4l2_async_notifier_init(&cio2->notifier);
 
+	r = devm_request_irq(dev, pci_dev->irq, cio2_irq, IRQF_SHARED,
+			     CIO2_NAME, cio2);
+	if (r) {
+		dev_err(dev, "failed to request IRQ (%d)\n", r);
+		goto fail_clean_notifier;
+	}
+
 	/* Register notifier for subdevices we care */
 	r = cio2_parse_firmware(cio2);
 	if (r)
 		goto fail_clean_notifier;
 
-	r = devm_request_irq(&pci_dev->dev, pci_dev->irq, cio2_irq,
-			     IRQF_SHARED, CIO2_NAME, cio2);
-	if (r) {
-		dev_err(&pci_dev->dev, "failed to request IRQ (%d)\n", r);
-		goto fail_clean_notifier;
-	}
-
-	pm_runtime_put_noidle(&pci_dev->dev);
-	pm_runtime_allow(&pci_dev->dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_allow(dev);
 
 	return 0;
 
@@ -1851,6 +1848,9 @@
 	v4l2_device_unregister(&cio2->v4l2_dev);
 	media_device_cleanup(&cio2->media_dev);
 	mutex_destroy(&cio2->lock);
+
+	pm_runtime_forbid(&pci_dev->dev);
+	pm_runtime_get_noresume(&pci_dev->dev);
 }
 
 static int __maybe_unused cio2_runtime_suspend(struct device *dev)
@@ -2005,10 +2005,9 @@
 	if (!cio2->streaming)
 		return 0;
 	/* Start stream */
-	r = pm_runtime_force_resume(&cio2->pci_dev->dev);
+	r = pm_runtime_force_resume(dev);
 	if (r < 0) {
-		dev_err(&cio2->pci_dev->dev,
-			"failed to set power %d\n", r);
+		dev_err(dev, "failed to set power %d\n", r);
 		return r;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/Makefile
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (c) 2017 - 2020 Intel Corporation.
+
+ifneq ($(EXTERNAL_BUILD), 1)
+srcpath := $(srctree)
+endif
+
+ccflags-y += -DIPU_TPG_FRAME_SYNC -DIPU_PSYS_GPC \
+		-DIPU_ISYS_GPC
+
+intel-ipu6-objs				+= ../ipu.o \
+					   ../ipu-bus.o \
+					   ../ipu-dma.o \
+					   ../ipu-mmu.o \
+					   ../ipu-buttress.o \
+					   ../ipu-trace.o \
+					   ../ipu-cpd.o \
+					   ipu6.o \
+					   ../ipu-fw-com.o
+
+obj-$(CONFIG_VIDEO_INTEL_IPU6)		+= intel-ipu6.o
+
+intel-ipu6-isys-objs			+= ../ipu-isys.o \
+					   ../ipu-isys-csi2.o \
+					   ipu6-isys.o \
+					   ipu6-isys-phy.o \
+					   ipu6-isys-csi2.o \
+					   ipu6-isys-gpc.o \
+					   ../ipu-isys-csi2-be-soc.o \
+					   ../ipu-fw-isys.o \
+					   ../ipu-isys-video.o \
+					   ../ipu-isys-queue.o \
+					   ../ipu-isys-subdev.o
+
+obj-$(CONFIG_VIDEO_INTEL_IPU6)		+= intel-ipu6-isys.o
+
+intel-ipu6-psys-objs			+= ../ipu-psys.o \
+					   ipu6-psys.o \
+					   ipu-resources.o \
+					   ipu6-psys-gpc.o \
+					   ipu6-l-scheduler.o \
+					   ipu6-ppg.o
+
+intel-ipu6-psys-objs			+= ipu-fw-resources.o \
+					   ipu6-fw-resources.o \
+					   ipu6se-fw-resources.o \
+					   ipu6ep-fw-resources.o \
+					   ../ipu-fw-psys.o
+
+ifeq ($(CONFIG_COMPAT),y)
+intel-ipu6-psys-objs			+= ../ipu-psys-compat32.o
+endif
+
+obj-$(CONFIG_VIDEO_INTEL_IPU6)		+= intel-ipu6-psys.o
+
+ccflags-y += -I$(srcpath)/$(src)/../../../../../include/
+ccflags-y += -I$(srcpath)/$(src)/../
+ccflags-y += -I$(srcpath)/$(src)/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-fw-resources.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-fw-resources.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2015 - 2019 Intel Corporation
+
+#include <linux/err.h>
+#include <linux/string.h>
+
+#include "ipu-psys.h"
+#include "ipu-fw-psys.h"
+#include "ipu6-platform-resources.h"
+#include "ipu6se-platform-resources.h"
+
+/********** Generic resource handling **********/
+
+/*
+ * Extension library gives byte offsets to its internal structures.
+ * use those offsets to update fields. Without extension lib access
+ * structures directly.
+ */
+const struct ipu6_psys_hw_res_variant *var = &hw_var;
+
+int ipu_fw_psys_set_process_cell_id(struct ipu_fw_psys_process *ptr, u8 index,
+				    u8 value)
+{
+	struct ipu_fw_psys_process_group *parent =
+		(struct ipu_fw_psys_process_group *)((char *)ptr +
+						      ptr->parent_offset);
+
+	ptr->cells[index] = value;
+	parent->resource_bitmap |= 1 << value;
+
+	return 0;
+}
+
+u8 ipu_fw_psys_get_process_cell_id(struct ipu_fw_psys_process *ptr, u8 index)
+{
+	return ptr->cells[index];
+}
+
+int ipu_fw_psys_clear_process_cell(struct ipu_fw_psys_process *ptr)
+{
+	struct ipu_fw_psys_process_group *parent;
+	u8 cell_id = ipu_fw_psys_get_process_cell_id(ptr, 0);
+	int retval = -1;
+	u8 value;
+
+	parent = (struct ipu_fw_psys_process_group *)((char *)ptr +
+						       ptr->parent_offset);
+
+	value = var->cell_num;
+	if ((1 << cell_id) != 0 &&
+	    ((1 << cell_id) & parent->resource_bitmap)) {
+		ipu_fw_psys_set_process_cell_id(ptr, 0, value);
+		parent->resource_bitmap &= ~(1 << cell_id);
+		retval = 0;
+	}
+
+	return retval;
+}
+
+int ipu_fw_psys_set_proc_dev_chn(struct ipu_fw_psys_process *ptr, u16 offset,
+				 u16 value)
+{
+	if (var->set_proc_dev_chn)
+		return var->set_proc_dev_chn(ptr, offset, value);
+
+	WARN(1, "ipu6 psys res var is not initialised correctly.");
+	return 0;
+}
+
+int ipu_fw_psys_set_proc_dfm_bitmap(struct ipu_fw_psys_process *ptr,
+				    u16 id, u32 bitmap,
+				    u32 active_bitmap)
+{
+	if (var->set_proc_dfm_bitmap)
+		return var->set_proc_dfm_bitmap(ptr, id, bitmap,
+						active_bitmap);
+
+	WARN(1, "ipu6 psys res var is not initialised correctly.");
+	return 0;
+}
+
+int ipu_fw_psys_set_process_ext_mem(struct ipu_fw_psys_process *ptr,
+				    u16 type_id, u16 mem_id, u16 offset)
+{
+	if (var->set_proc_ext_mem)
+		return var->set_proc_ext_mem(ptr, type_id, mem_id, offset);
+
+	WARN(1, "ipu6 psys res var is not initialised correctly.");
+	return 0;
+}
+
+int ipu_fw_psys_get_program_manifest_by_process(
+	struct ipu_fw_generic_program_manifest *gen_pm,
+	const struct ipu_fw_psys_program_group_manifest *pg_manifest,
+	struct ipu_fw_psys_process *process)
+{
+	if (var->get_pgm_by_proc)
+		return var->get_pgm_by_proc(gen_pm, pg_manifest, process);
+
+	WARN(1, "ipu6 psys res var is not initialised correctly.");
+	return 0;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform-buttress-regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform-buttress-regs.h
@@ -0,0 +1,318 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_BUTTRESS_REGS_H
+#define IPU_PLATFORM_BUTTRESS_REGS_H
+
+/* IS_WORKPOINT_REQ */
+#define IPU_BUTTRESS_REG_IS_FREQ_CTL		0x34
+/* PS_WORKPOINT_REQ */
+#define IPU_BUTTRESS_REG_PS_FREQ_CTL		0x38
+
+#define IPU_BUTTRESS_IS_FREQ_RATIO_MASK	0xff
+#define IPU_BUTTRESS_PS_FREQ_RATIO_MASK	0xff
+
+#define IPU_IS_FREQ_MAX		533
+#define IPU_IS_FREQ_MIN		200
+#define IPU_PS_FREQ_MAX		450
+#define IPU_IS_FREQ_RATIO_BASE		25
+#define IPU_PS_FREQ_RATIO_BASE		25
+#define IPU_BUTTRESS_IS_FREQ_CTL_DIVISOR_MASK	0xff
+#define IPU_BUTTRESS_PS_FREQ_CTL_DIVISOR_MASK	0xff
+
+/* should be tuned for real silicon */
+#define IPU_IS_FREQ_CTL_DEFAULT_RATIO		0x08
+#define IPU6SE_IS_FREQ_CTL_DEFAULT_RATIO	0x0a
+#define IPU_PS_FREQ_CTL_DEFAULT_RATIO		0x0d
+
+#define IPU_IS_FREQ_CTL_DEFAULT_QOS_FLOOR_RATIO	0x10
+#define IPU_PS_FREQ_CTL_DEFAULT_QOS_FLOOR_RATIO	0x0708
+
+#define IPU_BUTTRESS_PWR_STATE_IS_PWR_SHIFT	3
+#define IPU_BUTTRESS_PWR_STATE_IS_PWR_MASK	\
+	(0x3 << IPU_BUTTRESS_PWR_STATE_IS_PWR_SHIFT)
+
+#define IPU_BUTTRESS_PWR_STATE_PS_PWR_SHIFT	6
+#define IPU_BUTTRESS_PWR_STATE_PS_PWR_MASK	\
+	(0x3 << IPU_BUTTRESS_PWR_STATE_PS_PWR_SHIFT)
+
+#define IPU_BUTTRESS_PWR_STATE_DN_DONE		0x0
+#define IPU_BUTTRESS_PWR_STATE_UP_PROCESS	0x1
+#define IPU_BUTTRESS_PWR_STATE_DN_PROCESS	0x2
+#define IPU_BUTTRESS_PWR_STATE_UP_DONE		0x3
+
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_0	0x270
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_1	0x274
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_2	0x278
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_3	0x27c
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_4	0x280
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_5	0x284
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_6	0x288
+#define IPU_BUTTRESS_REG_FPGA_SUPPORT_7	0x28c
+
+#define BUTTRESS_REG_WDT			0x8
+#define BUTTRESS_REG_BTRS_CTRL			0xc
+#define BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC0	BIT(0)
+#define BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC1	BIT(1)
+#define BUTTRESS_REG_BTRS_CTRL_REF_CLK_IND	GENMASK(9, 8)
+
+#define BUTTRESS_REG_FW_RESET_CTL	0x30
+#define BUTTRESS_FW_RESET_CTL_START	BIT(0)
+#define BUTTRESS_FW_RESET_CTL_DONE	BIT(1)
+
+#define BUTTRESS_REG_IS_FREQ_CTL	0x34
+
+#define BUTTRESS_IS_FREQ_CTL_DIVISOR_MASK	0xf
+
+#define BUTTRESS_REG_PS_FREQ_CTL	0x38
+
+#define BUTTRESS_PS_FREQ_CTL_RATIO_MASK		0xff
+
+#define BUTTRESS_FREQ_CTL_START		BIT(31)
+#define BUTTRESS_FREQ_CTL_START_SHIFT		31
+#define BUTTRESS_FREQ_CTL_QOS_FLOOR_SHIFT	8
+#define BUTTRESS_FREQ_CTL_ICCMAX_LEVEL		(GENMASK(19, 16))
+#define BUTTRESS_FREQ_CTL_QOS_FLOOR_MASK	(0xff << 8)
+
+#define BUTTRESS_REG_PWR_STATE	0x5c
+
+#define BUTTRESS_PWR_STATE_IS_PWR_SHIFT	3
+#define BUTTRESS_PWR_STATE_IS_PWR_MASK	(0x3 << 3)
+
+#define BUTTRESS_PWR_STATE_PS_PWR_SHIFT	6
+#define BUTTRESS_PWR_STATE_PS_PWR_MASK	(0x3 << 6)
+
+#define BUTTRESS_PWR_STATE_RESET		0x0
+#define BUTTRESS_PWR_STATE_PWR_ON_DONE		0x1
+#define BUTTRESS_PWR_STATE_PWR_RDY		0x3
+#define BUTTRESS_PWR_STATE_PWR_IDLE		0x4
+
+#define BUTTRESS_PWR_STATE_HH_STATUS_SHIFT	11
+#define BUTTRESS_PWR_STATE_HH_STATUS_MASK	(0x3 << 11)
+
+enum {
+	BUTTRESS_PWR_STATE_HH_STATE_IDLE,
+	BUTTRESS_PWR_STATE_HH_STATE_IN_PRGS,
+	BUTTRESS_PWR_STATE_HH_STATE_DONE,
+	BUTTRESS_PWR_STATE_HH_STATE_ERR,
+};
+
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_SHIFT	19
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_MASK	(0xf << 19)
+
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_IDLE			0x0
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_WAIT_4_PLL_CMP		0x1
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_WAIT_4_CLKACK		0x2
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_WAIT_4_PG_ACK		0x3
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_RST_ASSRT_CYCLES		0x4
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_STOP_CLK_CYCLES1		0x5
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_STOP_CLK_CYCLES2		0x6
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_RST_DEASSRT_CYCLES	0x7
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_WAIT_4_FUSE_WR_CMP	0x8
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_BRK_POINT			0x9
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_IS_RDY			0xa
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_HALT_HALTED		0xb
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_RST_DURATION_CNT3		0xc
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_WAIT_4_CLKACK_PD		0xd
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_PD_BRK_POINT		0xe
+#define BUTTRESS_PWR_STATE_IS_PWR_FSM_WAIT_4_PD_PG_ACK0		0xf
+
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_SHIFT	24
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_MASK	(0x1f << 24)
+
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_IDLE			0x0
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_PU_PLL_IP_RDY	0x1
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_RO_PRE_CNT_EXH	0x2
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_PU_VGI_PWRGOOD	0x3
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_RO_POST_CNT_EXH	0x4
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WR_PLL_RATIO		0x5
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_PU_PLL_CMP		0x6
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_PU_CLKACK		0x7
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_RST_ASSRT_CYCLES		0x8
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_STOP_CLK_CYCLES1		0x9
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_STOP_CLK_CYCLES2		0xa
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_RST_DEASSRT_CYCLES	0xb
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_PU_BRK_PNT		0xc
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_FUSE_ACCPT		0xd
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_PS_PWR_UP			0xf
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_4_HALTED		0x10
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_RESET_CNT3		0x11
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_PD_CLKACK		0x12
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_PD_OFF_IND		0x13
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_DVFS_PH4		0x14
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_DVFS_PLL_CMP		0x15
+#define BUTTRESS_PWR_STATE_PS_PWR_FSM_WAIT_DVFS_CLKACK		0x16
+
+#define BUTTRESS_REG_SECURITY_CTL	0x300
+
+#define BUTTRESS_SECURITY_CTL_FW_SECURE_MODE	BIT(16)
+#define BUTTRESS_SECURITY_CTL_FW_SETUP_SHIFT		0
+#define BUTTRESS_SECURITY_CTL_FW_SETUP_MASK		0x1f
+
+#define BUTTRESS_SECURITY_CTL_FW_SETUP_DONE		0x1
+#define BUTTRESS_SECURITY_CTL_AUTH_DONE			0x2
+#define BUTTRESS_SECURITY_CTL_AUTH_FAILED			0x8
+
+#define BUTTRESS_REG_SENSOR_FREQ_CTL	0x16c
+
+#define BUTTRESS_SENSOR_FREQ_CTL_OSC_OUT_FREQ_DEFAULT(i) \
+					(0x1b << ((i) * 10))
+#define BUTTRESS_SENSOR_FREQ_CTL_OSC_OUT_FREQ_SHIFT(i)	((i) * 10)
+#define BUTTRESS_SENSOR_FREQ_CTL_OSC_OUT_FREQ_MASK(i) \
+					(0x1ff << ((i) * 10))
+
+#define BUTTRESS_SENSOR_CLK_FREQ_6P75MHZ	0x176
+#define BUTTRESS_SENSOR_CLK_FREQ_8MHZ		0x164
+#define BUTTRESS_SENSOR_CLK_FREQ_9P6MHZ		0x2
+#define BUTTRESS_SENSOR_CLK_FREQ_12MHZ		0x1b2
+#define BUTTRESS_SENSOR_CLK_FREQ_13P6MHZ	0x1ac
+#define BUTTRESS_SENSOR_CLK_FREQ_14P4MHZ	0x1cc
+#define BUTTRESS_SENSOR_CLK_FREQ_15P8MHZ	0x1a6
+#define BUTTRESS_SENSOR_CLK_FREQ_16P2MHZ	0xca
+#define BUTTRESS_SENSOR_CLK_FREQ_17P3MHZ	0x12e
+#define BUTTRESS_SENSOR_CLK_FREQ_18P6MHZ	0x1c0
+#define BUTTRESS_SENSOR_CLK_FREQ_19P2MHZ	0x0
+#define BUTTRESS_SENSOR_CLK_FREQ_24MHZ		0xb2
+#define BUTTRESS_SENSOR_CLK_FREQ_26MHZ		0xae
+#define BUTTRESS_SENSOR_CLK_FREQ_27MHZ		0x196
+
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_FB_RATIO_MASK		0xff
+#define BUTTRESS_SENSOR_FREQ_CTL_SEL_MIPICLK_A_SHIFT		8
+#define BUTTRESS_SENSOR_FREQ_CTL_SEL_MIPICLK_A_MASK		(0x2 << 8)
+#define BUTTRESS_SENSOR_FREQ_CTL_SEL_MIPICLK_C_SHIFT		10
+#define BUTTRESS_SENSOR_FREQ_CTL_SEL_MIPICLK_C_MASK		(0x2 << 10)
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_FORCE_OFF_SHIFT		12
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_REF_RATIO_SHIFT		14
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_REF_RATIO_MASK		(0x2 << 14)
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_PVD_RATIO_SHIFT		16
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_PVD_RATIO_MASK		(0x2 << 16)
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_OUTPUT_RATIO_SHIFT	18
+#define BUTTRESS_SENSOR_FREQ_CTL_LJPLL_OUTPUT_RATIO_MASK	(0x2 << 18)
+#define BUTTRESS_SENSOR_FREQ_CTL_START_SHIFT			31
+
+#define BUTTRESS_REG_SENSOR_CLK_CTL	0x170
+
+/* 0 <= i <= 2 */
+#define BUTTRESS_SENSOR_CLK_CTL_OSC_CLK_OUT_EN_SHIFT(i)		((i) * 2)
+#define BUTTRESS_SENSOR_CLK_CTL_OSC_CLK_OUT_SEL_SHIFT(i)	((i) * 2 + 1)
+
+#define BUTTRESS_REG_FW_SOURCE_BASE_LO	0x78
+#define BUTTRESS_REG_FW_SOURCE_BASE_HI	0x7C
+#define BUTTRESS_REG_FW_SOURCE_SIZE	0x80
+
+#define BUTTRESS_REG_ISR_STATUS		0x90
+#define BUTTRESS_REG_ISR_ENABLED_STATUS	0x94
+#define BUTTRESS_REG_ISR_ENABLE		0x98
+#define BUTTRESS_REG_ISR_CLEAR		0x9C
+
+#define BUTTRESS_ISR_IS_IRQ			BIT(0)
+#define BUTTRESS_ISR_PS_IRQ			BIT(1)
+#define BUTTRESS_ISR_IPC_EXEC_DONE_BY_CSE	BIT(2)
+#define BUTTRESS_ISR_IPC_EXEC_DONE_BY_ISH	BIT(3)
+#define BUTTRESS_ISR_IPC_FROM_CSE_IS_WAITING	BIT(4)
+#define BUTTRESS_ISR_IPC_FROM_ISH_IS_WAITING	BIT(5)
+#define BUTTRESS_ISR_CSE_CSR_SET		BIT(6)
+#define BUTTRESS_ISR_ISH_CSR_SET		BIT(7)
+#define BUTTRESS_ISR_SPURIOUS_CMP		BIT(8)
+#define BUTTRESS_ISR_WATCHDOG_EXPIRED		BIT(9)
+#define BUTTRESS_ISR_PUNIT_2_IUNIT_IRQ		BIT(10)
+#define BUTTRESS_ISR_SAI_VIOLATION		BIT(11)
+#define BUTTRESS_ISR_HW_ASSERTION		BIT(12)
+
+#define BUTTRESS_REG_IU2CSEDB0	0x100
+
+#define BUTTRESS_IU2CSEDB0_BUSY		BIT(31)
+#define BUTTRESS_IU2CSEDB0_SHORT_FORMAT_SHIFT	27
+#define BUTTRESS_IU2CSEDB0_CLIENT_ID_SHIFT	10
+#define BUTTRESS_IU2CSEDB0_IPC_CLIENT_ID_VAL	2
+
+#define BUTTRESS_REG_IU2CSEDATA0	0x104
+
+#define BUTTRESS_IU2CSEDATA0_IPC_BOOT_LOAD		1
+#define BUTTRESS_IU2CSEDATA0_IPC_AUTH_RUN		2
+#define BUTTRESS_IU2CSEDATA0_IPC_AUTH_REPLACE		3
+#define BUTTRESS_IU2CSEDATA0_IPC_UPDATE_SECURE_TOUCH	16
+
+#define BUTTRESS_CSE2IUDATA0_IPC_BOOT_LOAD_DONE			1
+#define BUTTRESS_CSE2IUDATA0_IPC_AUTH_RUN_DONE			2
+#define BUTTRESS_CSE2IUDATA0_IPC_AUTH_REPLACE_DONE		4
+#define BUTTRESS_CSE2IUDATA0_IPC_UPDATE_SECURE_TOUCH_DONE	16
+
+#define BUTTRESS_REG_IU2CSECSR		0x108
+
+#define BUTTRESS_IU2CSECSR_IPC_PEER_COMP_ACTIONS_RST_PHASE1		BIT(0)
+#define BUTTRESS_IU2CSECSR_IPC_PEER_COMP_ACTIONS_RST_PHASE2		BIT(1)
+#define BUTTRESS_IU2CSECSR_IPC_PEER_QUERIED_IP_COMP_ACTIONS_RST_PHASE	BIT(2)
+#define BUTTRESS_IU2CSECSR_IPC_PEER_ASSERTED_REG_VALID_REQ		BIT(3)
+#define BUTTRESS_IU2CSECSR_IPC_PEER_ACKED_REG_VALID			BIT(4)
+#define BUTTRESS_IU2CSECSR_IPC_PEER_DEASSERTED_REG_VALID_REQ		BIT(5)
+
+#define BUTTRESS_REG_CSE2IUDB0		0x304
+#define BUTTRESS_REG_CSE2IUCSR		0x30C
+#define BUTTRESS_REG_CSE2IUDATA0	0x308
+
+/* 0x20 == NACK, 0xf == unknown command */
+#define BUTTRESS_CSE2IUDATA0_IPC_NACK      0xf20
+#define BUTTRESS_CSE2IUDATA0_IPC_NACK_MASK 0xffff
+
+#define BUTTRESS_REG_ISH2IUCSR		0x50
+#define BUTTRESS_REG_ISH2IUDB0		0x54
+#define BUTTRESS_REG_ISH2IUDATA0	0x58
+
+#define BUTTRESS_REG_IU2ISHDB0		0x10C
+#define BUTTRESS_REG_IU2ISHDATA0	0x110
+#define BUTTRESS_REG_IU2ISHDATA1	0x114
+#define BUTTRESS_REG_IU2ISHCSR		0x118
+
+#define BUTTRESS_REG_ISH_START_DETECT		0x198
+#define BUTTRESS_REG_ISH_START_DETECT_MASK	0x19C
+
+#define BUTTRESS_REG_FABRIC_CMD	0x88
+
+#define BUTTRESS_FABRIC_CMD_START_TSC_SYNC	BIT(0)
+#define BUTTRESS_FABRIC_CMD_IS_DRAIN		BIT(4)
+
+#define BUTTRESS_REG_TSW_CTL		0x120
+#define BUTTRESS_TSW_CTL_SOFT_RESET	BIT(8)
+
+#define BUTTRESS_REG_TSC_LO	0x164
+#define BUTTRESS_REG_TSC_HI	0x168
+
+#define BUTTRESS_REG_CSI2_PORT_CONFIG_AB		0x200
+#define BUTTRESS_CSI2_PORT_CONFIG_AB_MUX_MASK		0x1f
+#define BUTTRESS_CSI2_PORT_CONFIG_AB_COMBO_SHIFT_B0	16
+
+#define BUTTRESS_REG_PS_FREQ_CAPABILITIES			0xf7498
+
+#define BUTTRESS_PS_FREQ_CAPABILITIES_LAST_RESOLVED_RATIO_SHIFT	24
+#define BUTTRESS_PS_FREQ_CAPABILITIES_LAST_RESOLVED_RATIO_MASK	(0xff << 24)
+#define BUTTRESS_PS_FREQ_CAPABILITIES_MAX_RATIO_SHIFT		16
+#define BUTTRESS_PS_FREQ_CAPABILITIES_MAX_RATIO_MASK		(0xff << 16)
+#define BUTTRESS_PS_FREQ_CAPABILITIES_EFFICIENT_RATIO_SHIFT	8
+#define BUTTRESS_PS_FREQ_CAPABILITIES_EFFICIENT_RATIO_MASK	(0xff << 8)
+#define BUTTRESS_PS_FREQ_CAPABILITIES_MIN_RATIO_SHIFT		0
+#define BUTTRESS_PS_FREQ_CAPABILITIES_MIN_RATIO_MASK		(0xff)
+
+#define BUTTRESS_IRQS		(BUTTRESS_ISR_IPC_FROM_CSE_IS_WAITING |	\
+				 BUTTRESS_ISR_IPC_EXEC_DONE_BY_CSE |	\
+				 BUTTRESS_ISR_IS_IRQ |			\
+				 BUTTRESS_ISR_PS_IRQ)
+
+#define IPU6SE_ISYS_PHY_0_BASE		0x10000
+
+/* only use BB0, BB2, BB4, and BB6 on PHY0 */
+#define IPU6SE_ISYS_PHY_BB_NUM		4
+
+/* offset from PHY base */
+#define PHY_CSI_CFG			0xc0
+#define PHY_CSI_RCOMP_CONTROL		0xc8
+#define PHY_CSI_BSCAN_EXCLUDE		0xd8
+
+#define PHY_CPHY_DLL_OVRD(x)		(0x100 + 0x100 * (x))
+#define PHY_DPHY_DLL_OVRD(x)		(0x14c + 0x100 * (x))
+#define PHY_CPHY_RX_CONTROL1(x)		(0x110 + 0x100 * (x))
+#define PHY_CPHY_RX_CONTROL2(x)		(0x114 + 0x100 * (x))
+#define PHY_DPHY_CFG(x)			(0x148 + 0x100 * (x))
+#define PHY_BB_AFE_CONFIG(x)		(0x174 + 0x100 * (x))
+
+#endif /* IPU_PLATFORM_BUTTRESS_REGS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform-isys-csi2-reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform-isys-csi2-reg.h
@@ -0,0 +1,277 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_ISYS_CSI2_REG_H
+#define IPU_PLATFORM_ISYS_CSI2_REG_H
+
+#define CSI_REG_BASE			0x220000
+#define CSI_REG_BASE_PORT(id)		((id) * 0x1000)
+
+#define IPU_CSI_PORT_A_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(0))
+#define IPU_CSI_PORT_B_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(1))
+#define IPU_CSI_PORT_C_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(2))
+#define IPU_CSI_PORT_D_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(3))
+#define IPU_CSI_PORT_E_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(4))
+#define IPU_CSI_PORT_F_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(5))
+#define IPU_CSI_PORT_G_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(6))
+#define IPU_CSI_PORT_H_ADDR_OFFSET	\
+		(CSI_REG_BASE + CSI_REG_BASE_PORT(7))
+
+/* CSI Port Genral Purpose Registers */
+#define CSI_REG_PORT_GPREG_SRST                 0x0
+#define CSI_REG_PORT_GPREG_CSI2_SLV_REG_SRST    0x4
+#define CSI_REG_PORT_GPREG_CSI2_PORT_CONTROL    0x8
+
+/*
+ * Port IRQs mapping events:
+ * IRQ0 - CSI_FE event
+ * IRQ1 - CSI_SYNC
+ * IRQ2 - S2M_SIDS0TO7
+ * IRQ3 - S2M_SIDS8TO15
+ */
+#define CSI_PORT_REG_BASE_IRQ_CSI               0x80
+#define CSI_PORT_REG_BASE_IRQ_CSI_SYNC          0xA0
+#define CSI_PORT_REG_BASE_IRQ_S2M_SIDS0TOS7     0xC0
+#define CSI_PORT_REG_BASE_IRQ_S2M_SIDS8TOS15    0xE0
+
+#define CSI_PORT_REG_BASE_IRQ_EDGE_OFFSET	0x0
+#define CSI_PORT_REG_BASE_IRQ_MASK_OFFSET	0x4
+#define CSI_PORT_REG_BASE_IRQ_STATUS_OFFSET	0x8
+#define CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET	0xc
+#define CSI_PORT_REG_BASE_IRQ_ENABLE_OFFSET	0x10
+#define CSI_PORT_REG_BASE_IRQ_LEVEL_NOT_PULSE_OFFSET	0x14
+
+#define IPU6SE_CSI_RX_ERROR_IRQ_MASK		0x7ffff
+#define IPU6_CSI_RX_ERROR_IRQ_MASK		0xfffff
+
+#define CSI_RX_NUM_ERRORS_IN_IRQ		20
+#define CSI_RX_NUM_IRQ				32
+
+#define IPU_CSI_RX_IRQ_FS_VC		1
+#define IPU_CSI_RX_IRQ_FE_VC		2
+
+/* PPI2CSI */
+#define CSI_REG_PPI2CSI_ENABLE                  0x200
+#define CSI_REG_PPI2CSI_CONFIG_PPI_INTF         0x204
+#define PPI_INTF_CONFIG_NOF_ENABLED_DATALANES_SHIFT	3
+#define PPI_INTF_CONFIG_RX_AUTO_CLKGATING_SHIFT		5
+#define CSI_REG_PPI2CSI_CONFIG_CSI_FEATURE      0x208
+
+enum CSI_PPI2CSI_CTRL {
+	CSI_PPI2CSI_DISABLE = 0,
+	CSI_PPI2CSI_ENABLE = 1,
+};
+
+/* CSI_FE */
+#define CSI_REG_CSI_FE_ENABLE                   0x280
+#define CSI_REG_CSI_FE_MODE                     0x284
+#define CSI_REG_CSI_FE_MUX_CTRL                 0x288
+#define CSI_REG_CSI_FE_SYNC_CNTR_SEL            0x290
+
+enum CSI_FE_ENABLE_TYPE {
+	CSI_FE_DISABLE = 0,
+	CSI_FE_ENABLE = 1,
+};
+
+enum CSI_FE_MODE_TYPE {
+	CSI_FE_DPHY_MODE = 0,
+	CSI_FE_CPHY_MODE = 1,
+};
+
+enum CSI_FE_INPUT_SELECTOR {
+	CSI_SENSOR_INPUT = 0,
+	CSI_MIPIGEN_INPUT = 1,
+};
+
+enum CSI_FE_SYNC_CNTR_SEL_TYPE {
+	CSI_CNTR_SENSOR_LINE_ID = (1 << 0),
+	CSI_CNTR_INT_LINE_PKT_ID = ~CSI_CNTR_SENSOR_LINE_ID,
+	CSI_CNTR_SENSOR_FRAME_ID = (1 << 1),
+	CSI_CNTR_INT_FRAME_PKT_ID = ~CSI_CNTR_SENSOR_FRAME_ID,
+};
+
+/* MIPI_PKT_GEN */
+#define CSI_REG_PIXGEN_COM_BASE_OFFSET		0x300
+
+#define IPU_CSI_PORT_A_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(0) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_B_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(1) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_C_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(2) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_D_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(3) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_E_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(4) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_F_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(5) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_G_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(6) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+#define IPU_CSI_PORT_H_PIXGEN_ADDR_OFFSET	\
+	(CSI_REG_BASE + CSI_REG_BASE_PORT(7) + CSI_REG_PIXGEN_COM_BASE_OFFSET)
+
+#define CSI_REG_PIXGEN_COM_ENABLE_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x300)
+#define CSI_REG_PIXGEN_COM_DTYPE_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x304)
+#define CSI_REG_PIXGEN_COM_VTYPE_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x308)
+#define CSI_REG_PIXGEN_COM_VCHAN_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x30C)
+#define CSI_REG_PIXGEN_COM_WCOUNT_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x310)
+/* PRBS */
+#define CSI_REG_PIXGEN_PRBS_RSTVAL_REG0_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x314)
+#define CSI_REG_PIXGEN_PRBS_RSTVAL_REG1_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x318)
+/* SYNC_GENERATOR_CONFIG */
+#define CSI_REG_PIXGEN_SYNG_FREE_RUN_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x31C)
+#define CSI_REG_PIXGEN_SYNG_PAUSE_REG_IDX(id)		\
+	(CSI_REG_BASE_PORT(id) + 0x320)
+#define CSI_REG_PIXGEN_SYNG_NOF_FRAME_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x324)
+#define CSI_REG_PIXGEN_SYNG_NOF_PIXEL_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x328)
+#define CSI_REG_PIXGEN_SYNG_NOF_LINE_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x32C)
+#define CSI_REG_PIXGEN_SYNG_HBLANK_CYC_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x330)
+#define CSI_REG_PIXGEN_SYNG_VBLANK_CYC_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x334)
+#define CSI_REG_PIXGEN_SYNG_STAT_HCNT_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x338)
+#define CSI_REG_PIXGEN_SYNG_STAT_VCNT_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x33C)
+#define CSI_REG_PIXGEN_SYNG_STAT_FCNT_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x340)
+#define CSI_REG_PIXGEN_SYNG_STAT_DONE_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x344)
+/* TPG */
+#define CSI_REG_PIXGEN_TPG_MODE_REG_IDX(id)		\
+	(CSI_REG_BASE_PORT(id) + 0x348)
+/* TPG: mask_cfg */
+#define CSI_REG_PIXGEN_TPG_HCNT_MASK_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x34C)
+#define CSI_REG_PIXGEN_TPG_VCNT_MASK_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x350)
+#define CSI_REG_PIXGEN_TPG_XYCNT_MASK_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x354)
+/* TPG: delta_cfg */
+#define CSI_REG_PIXGEN_TPG_HCNT_DELTA_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x358)
+#define CSI_REG_PIXGEN_TPG_VCNT_DELTA_REG_IDX(id)	\
+	(CSI_REG_BASE_PORT(id) + 0x35C)
+/* TPG: color_cfg */
+#define CSI_REG_PIXGEN_TPG_R1_REG_IDX(id)	(CSI_REG_BASE_PORT(id) + 0x360)
+#define CSI_REG_PIXGEN_TPG_G1_REG_IDX(id)	(CSI_REG_BASE_PORT(id) + 0x364)
+#define CSI_REG_PIXGEN_TPG_B1_REG_IDX(id)	(CSI_REG_BASE_PORT(id) + 0x368)
+#define CSI_REG_PIXGEN_TPG_R2_REG_IDX(id)	(CSI_REG_BASE_PORT(id) + 0x36C)
+#define CSI_REG_PIXGEN_TPG_G2_REG_IDX(id)	(CSI_REG_BASE_PORT(id) + 0x370)
+#define CSI_REG_PIXGEN_TPG_B2_REG_IDX(id)	(CSI_REG_BASE_PORT(id) + 0x374)
+
+#define CSI_REG_PIXGEN_PRBS_RSTVAL_REG0	CSI_REG_PIXGEN_PRBS_RSTVAL_REG0_IDX(0)
+#define CSI_REG_PIXGEN_PRBS_RSTVAL_REG1	CSI_REG_PIXGEN_PRBS_RSTVAL_REG1_IDX(0)
+#define CSI_REG_PIXGEN_COM_ENABLE_REG	CSI_REG_PIXGEN_COM_ENABLE_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_MODE_REG	CSI_REG_PIXGEN_TPG_MODE_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_R1_REG	CSI_REG_PIXGEN_TPG_R1_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_G1_REG	CSI_REG_PIXGEN_TPG_G1_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_B1_REG	CSI_REG_PIXGEN_TPG_B1_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_R2_REG	CSI_REG_PIXGEN_TPG_R2_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_G2_REG	CSI_REG_PIXGEN_TPG_G2_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_B2_REG	CSI_REG_PIXGEN_TPG_B2_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_HCNT_MASK_REG CSI_REG_PIXGEN_TPG_HCNT_MASK_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_VCNT_MASK_REG CSI_REG_PIXGEN_TPG_VCNT_MASK_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_XYCNT_MASK_REG	\
+	CSI_REG_PIXGEN_TPG_XYCNT_MASK_REG_IDX(0)
+
+#define CSI_REG_PIXGEN_SYNG_NOF_FRAME_REG	\
+	CSI_REG_PIXGEN_SYNG_NOF_FRAME_REG_IDX(0)
+#define CSI_REG_PIXGEN_SYNG_NOF_LINE_REG	\
+	CSI_REG_PIXGEN_SYNG_NOF_LINE_REG_IDX(0)
+#define CSI_REG_PIXGEN_SYNG_HBLANK_CYC_REG	\
+	CSI_REG_PIXGEN_SYNG_HBLANK_CYC_REG_IDX(0)
+#define CSI_REG_PIXGEN_SYNG_VBLANK_CYC_REG	\
+	CSI_REG_PIXGEN_SYNG_VBLANK_CYC_REG_IDX(0)
+#define CSI_REG_PIXGEN_SYNG_NOF_PIXEL_REG	\
+	CSI_REG_PIXGEN_SYNG_NOF_PIXEL_REG_IDX(0)
+#define CSI_REG_PIXGEN_COM_WCOUNT_REG	CSI_REG_PIXGEN_COM_WCOUNT_REG_IDX(0)
+#define CSI_REG_PIXGEN_COM_DTYPE_REG	CSI_REG_PIXGEN_COM_DTYPE_REG_IDX(0)
+#define CSI_REG_PIXGEN_COM_VTYPE_REG	CSI_REG_PIXGEN_COM_VTYPE_REG_IDX(0)
+#define CSI_REG_PIXGEN_COM_VCHAN_REG	CSI_REG_PIXGEN_COM_VCHAN_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_HCNT_DELTA_REG	\
+	CSI_REG_PIXGEN_TPG_HCNT_DELTA_REG_IDX(0)
+#define CSI_REG_PIXGEN_TPG_VCNT_DELTA_REG	\
+	CSI_REG_PIXGEN_TPG_VCNT_DELTA_REG_IDX(0)
+
+/* CSI HUB General Purpose Registers */
+#define CSI_REG_HUB_GPREG_SRST			(CSI_REG_BASE + 0x18000)
+#define CSI_REG_HUB_GPREG_SLV_REG_SRST		(CSI_REG_BASE + 0x18004)
+#define CSI_REG_HUB_GPREG_PHY_CONTROL(id)	\
+	(CSI_REG_BASE + 0x18008 + (id) * 0x8)
+#define CSI_REG_HUB_GPREG_PHY_CONTROL_RESET		BIT(4)
+#define CSI_REG_HUB_GPREG_PHY_CONTROL_PWR_EN		BIT(0)
+#define CSI_REG_HUB_GPREG_PHY_STATUS(id)	\
+	(CSI_REG_BASE + 0x1800c + (id) * 0x8)
+#define CSI_REG_HUB_GPREG_PHY_STATUS_POWER_ACK		BIT(0)
+#define CSI_REG_HUB_GPREG_PHY_STATUS_PHY_READY		BIT(4)
+
+#define CSI_REG_HUB_DRV_ACCESS_PORT(id)	(CSI_REG_BASE + 0x18018 + (id) * 4)
+#define CSI_REG_HUB_FW_ACCESS_PORT(id)	(CSI_REG_BASE + 0x17000 + (id) * 4)
+
+enum CSI_PORT_CLK_GATING_SWITCH {
+	CSI_PORT_CLK_GATING_OFF = 0,
+	CSI_PORT_CLK_GATING_ON = 1,
+};
+
+#define CSI_REG_BASE_HUB_IRQ                        0x18200
+
+#define IPU_NUM_OF_DLANE_REG_PORT0      2
+#define IPU_NUM_OF_DLANE_REG_PORT1      4
+#define IPU_NUM_OF_DLANE_REG_PORT2      4
+#define IPU_NUM_OF_DLANE_REG_PORT3      2
+#define IPU_NUM_OF_DLANE_REG_PORT4      2
+#define IPU_NUM_OF_DLANE_REG_PORT5      4
+#define IPU_NUM_OF_DLANE_REG_PORT6      4
+#define IPU_NUM_OF_DLANE_REG_PORT7      2
+
+/* ipu6se support 2 SIPs, 2 port per SIP, 4 ports 0..3
+ * sip0 - 0, 1
+ * sip1 - 2, 3
+ * 0 and 2 support 4 data lanes, 1 and 3 support 2 data lanes
+ * all offset are base from isys base address
+ */
+
+#define CSI2_HUB_GPREG_SIP_SRST(sip)			(0x238038 + (sip) * 4)
+#define CSI2_HUB_GPREG_SIP_FB_PORT_CFG(sip)		(0x238050 + (sip) * 4)
+
+#define CSI2_HUB_GPREG_DPHY_TIMER_INCR			(0x238040)
+#define CSI2_HUB_GPREG_HPLL_FREQ			(0x238044)
+#define CSI2_HUB_GPREG_IS_CLK_RATIO			(0x238048)
+#define CSI2_HUB_GPREG_HPLL_FREQ_ISCLK_RATE_OVERRIDE	(0x23804c)
+#define CSI2_HUB_GPREG_PORT_CLKGATING_DISABLE		(0x238058)
+#define CSI2_HUB_GPREG_SIP0_CSI_RX_A_CONTROL		(0x23805c)
+#define CSI2_HUB_GPREG_SIP0_CSI_RX_B_CONTROL		(0x238088)
+#define CSI2_HUB_GPREG_SIP1_CSI_RX_A_CONTROL		(0x2380a4)
+#define CSI2_HUB_GPREG_SIP1_CSI_RX_B_CONTROL		(0x2380d0)
+
+#define CSI2_SIP_TOP_CSI_RX_BASE(sip)		(0x23805c + (sip) * 0x48)
+#define CSI2_SIP_TOP_CSI_RX_PORT_BASE_0(port)	(0x23805c + ((port) / 2) * 0x48)
+#define CSI2_SIP_TOP_CSI_RX_PORT_BASE_1(port)	(0x238088 + ((port) / 2) * 0x48)
+
+/* offset from port base */
+#define CSI2_SIP_TOP_CSI_RX_PORT_CONTROL		(0x0)
+#define CSI2_SIP_TOP_CSI_RX_DLY_CNT_TERMEN_CLANE	(0x4)
+#define CSI2_SIP_TOP_CSI_RX_DLY_CNT_SETTLE_CLANE	(0x8)
+#define CSI2_SIP_TOP_CSI_RX_DLY_CNT_TERMEN_DLANE(lane)	(0xc + (lane) * 8)
+#define CSI2_SIP_TOP_CSI_RX_DLY_CNT_SETTLE_DLANE(lane)	(0x10 + (lane) * 8)
+
+#endif /* IPU6_ISYS_CSI2_REG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform-isys.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform-isys.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_ISYS_H
+#define IPU_PLATFORM_ISYS_H
+
+#define IPU_ISYS_ENTITY_PREFIX		"Intel IPU6"
+
+/*
+ * FW support max 16 streams
+ */
+#define IPU_ISYS_MAX_STREAMS		16
+
+#define ISYS_UNISPART_IRQS	(IPU_ISYS_UNISPART_IRQ_SW |	\
+				 IPU_ISYS_UNISPART_IRQ_CSI0 |	\
+				 IPU_ISYS_UNISPART_IRQ_CSI1)
+
+/* IPU6 ISYS compression alignment */
+#define IPU_ISYS_COMPRESSION_LINE_ALIGN		512
+#define IPU_ISYS_COMPRESSION_HEIGHT_ALIGN	1
+#define IPU_ISYS_COMPRESSION_TILE_SIZE_BYTES	512
+#define IPU_ISYS_COMPRESSION_PAGE_ALIGN		0x1000
+#define IPU_ISYS_COMPRESSION_TILE_STATUS_BITS	4
+#define IPU_ISYS_COMPRESSION_MAX		3
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform-psys.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform-psys.h
@@ -0,0 +1,78 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_PSYS_H
+#define IPU_PLATFORM_PSYS_H
+
+#include "ipu-psys.h"
+#include <uapi/linux/ipu-psys.h>
+
+#define IPU_PSYS_BUF_SET_POOL_SIZE 8
+#define IPU_PSYS_BUF_SET_MAX_SIZE 1024
+
+struct ipu_fw_psys_buffer_set;
+
+enum ipu_psys_cmd_state {
+	KCMD_STATE_PPG_NEW,
+	KCMD_STATE_PPG_START,
+	KCMD_STATE_PPG_ENQUEUE,
+	KCMD_STATE_PPG_STOP,
+	KCMD_STATE_PPG_COMPLETE
+};
+
+struct ipu_psys_scheduler {
+	struct list_head ppgs;
+	struct mutex bs_mutex;  /* Protects buf_set field */
+	struct list_head buf_sets;
+};
+
+enum ipu_psys_ppg_state {
+	PPG_STATE_START = (1 << 0),
+	PPG_STATE_STARTING = (1 << 1),
+	PPG_STATE_STARTED = (1 << 2),
+	PPG_STATE_RUNNING = (1 << 3),
+	PPG_STATE_SUSPEND = (1 << 4),
+	PPG_STATE_SUSPENDING = (1 << 5),
+	PPG_STATE_SUSPENDED = (1 << 6),
+	PPG_STATE_RESUME = (1 << 7),
+	PPG_STATE_RESUMING = (1 << 8),
+	PPG_STATE_RESUMED = (1 << 9),
+	PPG_STATE_STOP = (1 << 10),
+	PPG_STATE_STOPPING = (1 << 11),
+	PPG_STATE_STOPPED = (1 << 12),
+};
+
+struct ipu_psys_ppg {
+	struct ipu_psys_pg *kpg;
+	struct ipu_psys_fh *fh;
+	struct list_head list;
+	struct list_head sched_list;
+	u64 token;
+	void *manifest;
+	struct mutex mutex;     /* Protects kcmd and ppg state field */
+	struct list_head kcmds_new_list;
+	struct list_head kcmds_processing_list;
+	struct list_head kcmds_finished_list;
+	enum ipu_psys_ppg_state state;
+	u32 pri_base;
+	int pri_dynamic;
+};
+
+struct ipu_psys_buffer_set {
+	struct list_head list;
+	struct ipu_fw_psys_buffer_set *buf_set;
+	size_t size;
+	size_t buf_set_size;
+	dma_addr_t dma_addr;
+	void *kaddr;
+	struct ipu_psys_kcmd *kcmd;
+};
+
+int ipu_psys_kcmd_start(struct ipu_psys *psys, struct ipu_psys_kcmd *kcmd);
+void ipu_psys_kcmd_complete(struct ipu_psys_ppg *kppg,
+			    struct ipu_psys_kcmd *kcmd,
+			    int error);
+int ipu_psys_fh_init(struct ipu_psys_fh *fh);
+int ipu_psys_fh_deinit(struct ipu_psys_fh *fh);
+
+#endif /* IPU_PLATFORM_PSYS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform-regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform-regs.h
@@ -0,0 +1,333 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 - 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_REGS_H
+#define IPU_PLATFORM_REGS_H
+
+/*
+ * IPU6 uses uniform address within IPU, therefore all subsystem registers
+ * locates in one signle space starts from 0 but in different sctions with
+ * different addresses, the subsystem offsets are defined to 0 as the
+ * register definition will have the address offset to 0.
+ */
+#define IPU_UNIFIED_OFFSET			0
+
+#define IPU_ISYS_IOMMU0_OFFSET		0x2E0000
+#define IPU_ISYS_IOMMU1_OFFSET		0x2E0500
+#define IPU_ISYS_IOMMUI_OFFSET		0x2E0A00
+
+#define IPU_PSYS_IOMMU0_OFFSET		0x1B0000
+#define IPU_PSYS_IOMMU1_OFFSET		0x1B0700
+#define IPU_PSYS_IOMMU1R_OFFSET		0x1B0E00
+#define IPU_PSYS_IOMMUI_OFFSET		0x1B1500
+
+/* the offset from IOMMU base register */
+#define IPU_MMU_L1_STREAM_ID_REG_OFFSET	0x0c
+#define IPU_MMU_L2_STREAM_ID_REG_OFFSET	0x4c
+#define IPU_PSYS_MMU1W_L2_STREAM_ID_REG_OFFSET	0x8c
+
+#define IPU_MMU_INFO_OFFSET		0x8
+
+#define IPU_ISYS_SPC_OFFSET		0x210000
+
+#define IPU6SE_PSYS_SPC_OFFSET		0x110000
+#define IPU6_PSYS_SPC_OFFSET		0x118000
+
+#define IPU_ISYS_DMEM_OFFSET		0x200000
+#define IPU_PSYS_DMEM_OFFSET		0x100000
+
+#define IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_EDGE		0x238200
+#define IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_MASK		0x238204
+#define IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_STATUS		0x238208
+#define IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_CLEAR		0x23820c
+#define IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_ENABLE		0x238210
+#define IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_LEVEL_NOT_PULSE	0x238214
+
+#define IPU_REG_ISYS_CSI_TOP_CTRL1_IRQ_EDGE		0x238220
+#define IPU_REG_ISYS_CSI_TOP_CTRL1_IRQ_MASK		0x238224
+#define IPU_REG_ISYS_CSI_TOP_CTRL1_IRQ_STATUS		0x238228
+#define IPU_REG_ISYS_CSI_TOP_CTRL1_IRQ_CLEAR		0x23822c
+#define IPU_REG_ISYS_CSI_TOP_CTRL1_IRQ_ENABLE		0x238230
+#define IPU_REG_ISYS_CSI_TOP_CTRL1_IRQ_LEVEL_NOT_PULSE	0x238234
+
+#define IPU_REG_ISYS_UNISPART_IRQ_EDGE			0x27c000
+#define IPU_REG_ISYS_UNISPART_IRQ_MASK			0x27c004
+#define IPU_REG_ISYS_UNISPART_IRQ_STATUS		0x27c008
+#define IPU_REG_ISYS_UNISPART_IRQ_CLEAR			0x27c00c
+#define IPU_REG_ISYS_UNISPART_IRQ_ENABLE			0x27c010
+#define IPU_REG_ISYS_UNISPART_IRQ_LEVEL_NOT_PULSE	0x27c014
+#define IPU_REG_ISYS_UNISPART_SW_IRQ_REG			0x27c414
+#define IPU_REG_ISYS_UNISPART_SW_IRQ_MUX_REG		0x27c418
+#define IPU_ISYS_UNISPART_IRQ_CSI0			BIT(2)
+#define IPU_ISYS_UNISPART_IRQ_CSI1			BIT(3)
+#define IPU_ISYS_UNISPART_IRQ_SW			BIT(22)
+
+#define IPU_REG_ISYS_ISL_TOP_IRQ_EDGE			0x2b0200
+#define IPU_REG_ISYS_ISL_TOP_IRQ_MASK			0x2b0204
+#define IPU_REG_ISYS_ISL_TOP_IRQ_STATUS			0x2b0208
+#define IPU_REG_ISYS_ISL_TOP_IRQ_CLEAR			0x2b020c
+#define IPU_REG_ISYS_ISL_TOP_IRQ_ENABLE			0x2b0210
+#define IPU_REG_ISYS_ISL_TOP_IRQ_LEVEL_NOT_PULSE	0x2b0214
+
+#define IPU_REG_ISYS_CMPR_TOP_IRQ_EDGE			0x2d2100
+#define IPU_REG_ISYS_CMPR_TOP_IRQ_MASK			0x2d2104
+#define IPU_REG_ISYS_CMPR_TOP_IRQ_STATUS		0x2d2108
+#define IPU_REG_ISYS_CMPR_TOP_IRQ_CLEAR			0x2d210c
+#define IPU_REG_ISYS_CMPR_TOP_IRQ_ENABLE		0x2d2110
+#define IPU_REG_ISYS_CMPR_TOP_IRQ_LEVEL_NOT_PULSE	0x2d2114
+
+/* CDC Burst collector thresholds for isys - 3 FIFOs i = 0..2 */
+#define IPU_REG_ISYS_CDC_THRESHOLD(i)		(0x27c400 + ((i) * 4))
+
+#define IPU_ISYS_CSI_PHY_NUM				2
+#define IPU_CSI_IRQ_NUM_PER_PIPE			4
+#define IPU6SE_ISYS_CSI_PORT_NUM			4
+#define IPU6_ISYS_CSI_PORT_NUM				8
+
+#define IPU_ISYS_CSI_PORT_IRQ(irq_num)		(1 << (irq_num))
+
+/* PSYS Info bits*/
+#define IPU_REG_PSYS_INFO_SEG_CMEM_MASTER(a)	(0x2C + ((a) * 12))
+#define IPU_REG_PSYS_INFO_SEG_XMEM_MASTER(a)	(0x5C + ((a) * 12))
+
+/* PKG DIR OFFSET in IMR in secure mode */
+#define IPU_PKG_DIR_IMR_OFFSET			0x40
+
+#define IPU_ISYS_REG_SPC_STATUS_CTRL		0x0
+
+#define IPU_ISYS_SPC_STATUS_START			BIT(1)
+#define IPU_ISYS_SPC_STATUS_RUN				BIT(3)
+#define IPU_ISYS_SPC_STATUS_READY			BIT(5)
+#define IPU_ISYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE	BIT(12)
+#define IPU_ISYS_SPC_STATUS_ICACHE_PREFETCH		BIT(13)
+
+#define IPU_PSYS_REG_SPC_STATUS_CTRL		0x0
+#define IPU_PSYS_REG_SPC_START_PC		0x4
+#define IPU_PSYS_REG_SPC_ICACHE_BASE		0x10
+#define IPU_REG_PSYS_INFO_SEG_0_CONFIG_ICACHE_MASTER	0x14
+
+#define IPU_PSYS_SPC_STATUS_START			BIT(1)
+#define IPU_PSYS_SPC_STATUS_RUN				BIT(3)
+#define IPU_PSYS_SPC_STATUS_READY			BIT(5)
+#define IPU_PSYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE	BIT(12)
+#define IPU_PSYS_SPC_STATUS_ICACHE_PREFETCH		BIT(13)
+
+#define IPU_PSYS_REG_SPP0_STATUS_CTRL			0x20000
+
+#define IPU_INFO_ENABLE_SNOOP			BIT(0)
+#define IPU_INFO_DEC_FORCE_FLUSH		BIT(1)
+#define IPU_INFO_DEC_PASS_THRU			BIT(2)
+#define IPU_INFO_ZLW                            BIT(3)
+#define IPU_INFO_STREAM_ID_SET(id)		(((id) & 0x1F) << 4)
+#define IPU_INFO_REQUEST_DESTINATION_IOSF	BIT(9)
+#define IPU_INFO_IMR_BASE			BIT(10)
+#define IPU_INFO_IMR_DESTINED			BIT(11)
+
+#define IPU_INFO_REQUEST_DESTINATION_PRIMARY IPU_INFO_REQUEST_DESTINATION_IOSF
+
+/* Trace unit related register definitions */
+#define TRACE_REG_MAX_ISYS_OFFSET	0xfffff
+#define TRACE_REG_MAX_PSYS_OFFSET	0xfffff
+#define IPU_ISYS_OFFSET			IPU_ISYS_DMEM_OFFSET
+#define IPU_PSYS_OFFSET			IPU_PSYS_DMEM_OFFSET
+/* ISYS trace unit registers */
+/* Trace unit base offset */
+#define IPU_TRACE_REG_IS_TRACE_UNIT_BASE		0x27d000
+/* Trace monitors */
+#define IPU_TRACE_REG_IS_SP_EVQ_BASE		0x211000
+/* GPC blocks */
+#define IPU_TRACE_REG_IS_SP_GPC_BASE		0x210800
+#define IPU_TRACE_REG_IS_ISL_GPC_BASE		0x2b0a00
+#define IPU_TRACE_REG_IS_MMU_GPC_BASE		0x2e0f00
+/* each CSI2 port has a dedicated trace monitor, index 0..7 */
+#define IPU_TRACE_REG_CSI2_TM_BASE(port)	(0x220400 + 0x1000 * (port))
+
+/* Trace timers */
+#define IPU_TRACE_REG_IS_GPREG_TRACE_TIMER_RST_N		0x27c410
+#define TRACE_REG_GPREG_TRACE_TIMER_RST_OFF		BIT(0)
+
+/* SIG2CIO */
+#define IPU_TRACE_REG_CSI2_PORT_SIG2SIO_GR_BASE(port)		\
+			(0x220e00 + (port) * 0x1000)
+
+/* PSYS trace unit registers */
+/* Trace unit base offset */
+#define IPU_TRACE_REG_PS_TRACE_UNIT_BASE		0x1b4000
+/* Trace monitors */
+#define IPU_TRACE_REG_PS_SPC_EVQ_BASE			0x119000
+#define IPU_TRACE_REG_PS_SPP0_EVQ_BASE			0x139000
+
+/* GPC blocks */
+#define IPU_TRACE_REG_PS_SPC_GPC_BASE			0x118800
+#define IPU_TRACE_REG_PS_SPP0_GPC_BASE			0x138800
+#define IPU_TRACE_REG_PS_MMU_GPC_BASE			0x1b1b00
+
+/* Trace timers */
+#define IPU_TRACE_REG_PS_GPREG_TRACE_TIMER_RST_N	0x1aa714
+
+/*
+ * s2m_pixel_soc_pixel_remapping is dedicated for the enableing of the
+ * pixel s2m remp ability.Remap here  means that s2m rearange the order
+ * of the pixels in each 4 pixels group.
+ * For examle, mirroring remping means that if input's 4 first pixels
+ * are 1 2 3 4 then in output we should see 4 3 2 1 in this 4 first pixels.
+ * 0xE4 is from s2m MAS document. It means no remaping.
+ */
+#define S2M_PIXEL_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING 0xE4
+/*
+ * csi_be_soc_pixel_remapping is for the enabling of the csi\mipi be pixel
+ * remapping feature. This remapping is exactly like the stream2mmio remapping.
+ */
+#define CSI_BE_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING    0xE4
+
+#define IPU_REG_DMA_TOP_AB_GROUP1_BASE_ADDR         0x1AE000
+#define IPU_REG_DMA_TOP_AB_GROUP2_BASE_ADDR         0x1AF000
+#define IPU_REG_DMA_TOP_AB_RING_MIN_OFFSET(n)       (0x4 + (n) * 0xC)
+#define IPU_REG_DMA_TOP_AB_RING_MAX_OFFSET(n)       (0x8 + (n) * 0xC)
+#define IPU_REG_DMA_TOP_AB_RING_ACCESS_OFFSET(n)    (0xC + (n) * 0xC)
+
+enum ipu_device_ab_group1_target_id {
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R0_SPC_DMEM,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R1_SPC_DMEM,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R2_SPC_DMEM,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R3_SPC_STATUS_REG,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R4_SPC_MASTER_BASE_ADDR,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R5_SPC_PC_STALL,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R6_SPC_EQ,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R7_SPC_RESERVED,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R8_SPC_RESERVED,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R9_SPP0,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R10_SPP1,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R11_CENTRAL_R1,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R12_IRQ,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R13_CENTRAL_R2,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R14_DMA,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R15_DMA,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R16_GP,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R17_ZLW_INSERTER,
+	IPU_DEVICE_AB_GROUP1_TARGET_ID_R18_AB,
+};
+
+enum nci_ab_access_mode {
+	NCI_AB_ACCESS_MODE_RW,	/* read & write */
+	NCI_AB_ACCESS_MODE_RO,	/* read only */
+	NCI_AB_ACCESS_MODE_WO,	/* write only */
+	NCI_AB_ACCESS_MODE_NA	/* No access at all */
+};
+
+/*
+ * 3:0 CSI_PORT.irq_out[3:0] CSI_PORT_CTRL0 IRQ outputs (4bits)
+ * [0] CSI_PORT.IRQ_CTRL0_csi
+ * [1] CSI_PORT.IRQ_CTRL1_csi_sync
+ * [2] CSI_PORT.IRQ_CTRL2_s2m_sids0to7
+ * [3] CSI_PORT.IRQ_CTRL3_s2m_sids8to15
+ */
+#define IPU_ISYS_UNISPART_IRQ_CSI2(port)		\
+				   (0x3 << ((port) * IPU_CSI_IRQ_NUM_PER_PIPE))
+
+/* IRQ-related registers in PSYS */
+#define IPU_REG_PSYS_GPDEV_IRQ_EDGE		0x1aa200
+#define IPU_REG_PSYS_GPDEV_IRQ_MASK		0x1aa204
+#define IPU_REG_PSYS_GPDEV_IRQ_STATUS		0x1aa208
+#define IPU_REG_PSYS_GPDEV_IRQ_CLEAR		0x1aa20c
+#define IPU_REG_PSYS_GPDEV_IRQ_ENABLE		0x1aa210
+#define IPU_REG_PSYS_GPDEV_IRQ_LEVEL_NOT_PULSE	0x1aa214
+/* There are 8 FW interrupts, n = 0..7 */
+#define IPU_PSYS_GPDEV_FWIRQ0			5
+#define IPU_PSYS_GPDEV_FWIRQ1			6
+#define IPU_PSYS_GPDEV_FWIRQ2			7
+#define IPU_PSYS_GPDEV_FWIRQ3			8
+#define IPU_PSYS_GPDEV_FWIRQ4			9
+#define IPU_PSYS_GPDEV_FWIRQ5			10
+#define IPU_PSYS_GPDEV_FWIRQ6			11
+#define IPU_PSYS_GPDEV_FWIRQ7			12
+#define IPU_PSYS_GPDEV_IRQ_FWIRQ(n)		(1 << (n))
+#define IPU_REG_PSYS_GPDEV_FWIRQ(n)		(4 * (n) + 0x1aa100)
+
+/*
+ * ISYS GPC (Gerneral Performance Counters) Registers
+ */
+#define IPU_ISYS_GPC_BASE			0x2E0000
+#define IPU_ISYS_GPREG_TRACE_TIMER_RST		0x27C410
+enum ipu_isf_cdc_mmu_gpc_registers {
+	IPU_ISF_CDC_MMU_GPC_SOFT_RESET  = 0x0F00,
+	IPU_ISF_CDC_MMU_GPC_OVERALL_ENABLE  = 0x0F04,
+	IPU_ISF_CDC_MMU_GPC_ENABLE0  = 0x0F20,
+	IPU_ISF_CDC_MMU_GPC_VALUE0  = 0x0F60,
+	IPU_ISF_CDC_MMU_GPC_CNT_SEL0 = 0x0FA0,
+};
+
+/*
+ * GPC (Gerneral Performance Counters) Registers
+ */
+#define IPU_GPC_BASE 0x1B0000
+#define IPU_GPREG_TRACE_TIMER_RST	0x1AA714
+enum ipu_cdc_mmu_gpc_registers {
+	IPU_CDC_MMU_GPC_SOFT_RESET  = 0x1B00,
+	IPU_CDC_MMU_GPC_OVERALL_ENABLE  = 0x1B04,
+	IPU_CDC_MMU_GPC_TRACE_HEADER  = 0x1B08,
+	IPU_CDC_MMU_GPC_TRACE_ADDR  = 0x1B0C,
+	IPU_CDC_MMU_GPC_TRACE_ENABLE_NPK  = 0x1B10,
+	IPU_CDC_MMU_GPC_TRACE_ENABLE_DDR  = 0x1B14,
+	IPU_CDC_MMU_GPC_LP_CLEAR  = 0x1B18,
+	IPU_CDC_MMU_GPC_LOST_PACKET  = 0x1B1C,
+	IPU_CDC_MMU_GPC_ENABLE0  = 0x1B20,
+	IPU_CDC_MMU_GPC_VALUE0  = 0x1B60,
+	IPU_CDC_MMU_GPC_CNT_SEL0 = 0x1BA0,
+	IPU_CDC_MMU_GPC_START_SEL0 = 0x1BE0,
+	IPU_CDC_MMU_GPC_STOP_SEL0 = 0x1C20,
+	IPU_CDC_MMU_GPC_MSG_SEL0 = 0x1C60,
+	IPU_CDC_MMU_GPC_PLOAD_SEL0 = 0x1CA0,
+	IPU_CDC_MMU_GPC_IRQ_TRIGGER_VALUE0 = 0x1CE0,
+	IPU_CDC_MMU_GPC_IRQ_TIMER_SEL0 = 0x1D20,
+	IPU_CDC_MMU_GPC_IRQ_ENABLE0 = 0x1D60,
+	IPU_CDC_MMU_GPC_END = 0x1D9C
+};
+
+#define IPU_GPC_SENSE_OFFSET		7
+#define IPU_GPC_ROUTE_OFFSET		5
+#define IPU_GPC_SOURCE_OFFSET		0
+
+/*
+ * Signals monitored by GPC
+ */
+#define IPU_GPC_TRACE_TLB_MISS_MMU_LB_IDX		0
+#define IPU_GPC_TRACE_FULL_WRITE_LB_IDX			1
+#define IPU_GPC_TRACE_NOFULL_WRITE_LB_IDX		2
+#define IPU_GPC_TRACE_FULL_READ_LB_IDX			3
+#define IPU_GPC_TRACE_NOFULL_READ_LB_IDX		4
+#define IPU_GPC_TRACE_STALL_LB_IDX			5
+#define IPU_GPC_TRACE_ZLW_LB_IDX			6
+#define IPU_GPC_TRACE_TLB_MISS_MMU_HBTX_IDX		7
+#define IPU_GPC_TRACE_FULL_WRITE_HBTX_IDX		8
+#define IPU_GPC_TRACE_NOFULL_WRITE_HBTX_IDX		9
+#define IPU_GPC_TRACE_FULL_READ_HBTX_IDX		10
+#define IPU_GPC_TRACE_STALL_HBTX_IDX			11
+#define IPU_GPC_TRACE_ZLW_HBTX_IDX			12
+#define IPU_GPC_TRACE_TLB_MISS_MMU_HBFRX_IDX		13
+#define IPU_GPC_TRACE_FULL_READ_HBFRX_IDX		14
+#define IPU_GPC_TRACE_NOFULL_READ_HBFRX_IDX		15
+#define IPU_GPC_TRACE_STALL_HBFRX_IDX			16
+#define IPU_GPC_TRACE_ZLW_HBFRX_IDX			17
+#define IPU_GPC_TRACE_TLB_MISS_ICACHE_IDX		18
+#define IPU_GPC_TRACE_FULL_READ_ICACHE_IDX		19
+#define IPU_GPC_TRACE_STALL_ICACHE_IDX			20
+/*
+ * psys subdomains power request regs
+ */
+enum ipu_device_buttress_psys_domain_pos {
+	IPU_PSYS_SUBDOMAIN_ISA		= 0,
+	IPU_PSYS_SUBDOMAIN_PSA		= 1,
+	IPU_PSYS_SUBDOMAIN_BB		= 2,
+	IPU_PSYS_SUBDOMAIN_IDSP1	= 3, /* only in IPU6M */
+	IPU_PSYS_SUBDOMAIN_IDSP2	= 4, /* only in IPU6M */
+};
+
+#define IPU_PSYS_SUBDOMAINS_POWER_MASK  (BIT(IPU_PSYS_SUBDOMAIN_ISA) | \
+					 BIT(IPU_PSYS_SUBDOMAIN_PSA) | \
+					 BIT(IPU_PSYS_SUBDOMAIN_BB))
+
+#define IPU_PSYS_SUBDOMAINS_POWER_REQ                   0xa0
+#define IPU_PSYS_SUBDOMAINS_POWER_STATUS                0xa4
+
+#endif /* IPU_PLATFORM_REGS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform-resources.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform-resources.h
@@ -0,0 +1,103 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 - 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_RESOURCES_COMMON_H
+#define IPU_PLATFORM_RESOURCES_COMMON_H
+
+#define IPU_FW_PSYS_N_PADDING_UINT8_IN_PROGRAM_MANIFEST                 0
+
+#define	IPU_FW_PSYS_N_PADDING_UINT8_IN_PROCESS_STRUCT			0
+#define	IPU_FW_PSYS_N_PADDING_UINT8_IN_PROCESS_GROUP_STRUCT		2
+#define	IPU_FW_PSYS_N_PADDING_UINT8_IN_PROGRAM_MANIFEST_EXT		2
+
+#define IPU_FW_PSYS_N_PADDING_UINT8_IN_TERMINAL_STRUCT			5
+
+#define IPU_FW_PSYS_N_PADDING_UINT8_IN_PARAM_TERMINAL_STRUCT		6
+
+#define	IPU_FW_PSYS_N_PADDING_UINT8_IN_DATA_TERMINAL_STRUCT		3
+
+#define	IPU_FW_PSYS_N_PADDING_UINT8_IN_FRAME_DESC_STRUCT		3
+#define IPU_FW_PSYS_N_FRAME_PLANES					6
+#define IPU_FW_PSYS_N_PADDING_UINT8_IN_FRAME_STRUCT			4
+
+#define IPU_FW_PSYS_N_PADDING_UINT8_IN_BUFFER_SET_STRUCT		1
+
+#define IPU_FW_PSYS_MAX_INPUT_DEC_RESOURCES		4
+#define IPU_FW_PSYS_MAX_OUTPUT_DEC_RESOURCES		4
+
+#define IPU_FW_PSYS_PROCESS_MAX_CELLS			1
+#define IPU_FW_PSYS_KERNEL_BITMAP_NOF_ELEMS		4
+#define IPU_FW_PSYS_RBM_NOF_ELEMS			5
+#define IPU_FW_PSYS_KBM_NOF_ELEMS			4
+
+struct ipu_fw_psys_process {
+	s16 parent_offset;
+	u8 size;
+	u8 cell_dependencies_offset;
+	u8 terminal_dependencies_offset;
+	u8 process_extension_offset;
+	u8 ID;
+	u8 program_idx;
+	u8 state;
+	u8 cells[IPU_FW_PSYS_PROCESS_MAX_CELLS];
+	u8 cell_dependency_count;
+	u8 terminal_dependency_count;
+};
+
+struct ipu_fw_psys_program_manifest {
+	u32 kernel_bitmap[IPU_FW_PSYS_KERNEL_BITMAP_NOF_ELEMS];
+	s16 parent_offset;
+	u8  program_dependency_offset;
+	u8  terminal_dependency_offset;
+	u8  size;
+	u8  program_extension_offset;
+	u8 program_type;
+	u8 ID;
+	u8 cells[IPU_FW_PSYS_PROCESS_MAX_CELLS];
+	u8 cell_type_id;
+	u8 program_dependency_count;
+	u8 terminal_dependency_count;
+};
+
+/* platform specific resource interface */
+struct ipu_psys_resource_pool;
+struct ipu_psys_resource_alloc;
+struct ipu_fw_psys_process_group;
+int ipu_psys_allocate_resources(const struct device *dev,
+				struct ipu_fw_psys_process_group *pg,
+				void *pg_manifest,
+				struct ipu_psys_resource_alloc *alloc,
+				struct ipu_psys_resource_pool *pool);
+int ipu_psys_move_resources(const struct device *dev,
+			    struct ipu_psys_resource_alloc *alloc,
+			    struct ipu_psys_resource_pool *source_pool,
+			    struct ipu_psys_resource_pool *target_pool);
+
+void ipu_psys_resource_copy(struct ipu_psys_resource_pool *src,
+			    struct ipu_psys_resource_pool *dest);
+
+int ipu_psys_try_allocate_resources(struct device *dev,
+				    struct ipu_fw_psys_process_group *pg,
+				    void *pg_manifest,
+				    struct ipu_psys_resource_pool *pool);
+
+void ipu_psys_reset_process_cell(const struct device *dev,
+				 struct ipu_fw_psys_process_group *pg,
+				 void *pg_manifest,
+				 int process_count);
+void ipu_psys_free_resources(struct ipu_psys_resource_alloc *alloc,
+			     struct ipu_psys_resource_pool *pool);
+
+int ipu_fw_psys_set_proc_dfm_bitmap(struct ipu_fw_psys_process *ptr,
+				    u16 id, u32 bitmap,
+				    u32 active_bitmap);
+
+int ipu_psys_allocate_cmd_queue_resource(struct ipu_psys_resource_pool *pool);
+void ipu_psys_free_cmd_queue_resource(struct ipu_psys_resource_pool *pool,
+				      u8 queue_id);
+
+extern const struct ipu_fw_resource_definitions *ipu6_res_defs;
+extern const struct ipu_fw_resource_definitions *ipu6se_res_defs;
+extern const struct ipu_fw_resource_definitions *ipu6ep_res_defs;
+extern struct ipu6_psys_hw_res_variant hw_var;
+#endif /* IPU_PLATFORM_RESOURCES_COMMON_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-platform.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-platform.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef IPU_PLATFORM_H
+#define IPU_PLATFORM_H
+
+#define IPU_NAME			"intel-ipu6"
+
+#define IPU6SE_FIRMWARE_NAME		"intel/ipu6se_fw.bin"
+#define IPU6EP_FIRMWARE_NAME		"intel/ipu6ep_fw.bin"
+#define IPU6EPES_FIRMWARE_NAME		"intel/ipu6epes_fw.bin"
+#define IPU6_FIRMWARE_NAME		"intel/ipu6_fw.bin"
+
+/*
+ * The following definitions are encoded to the media_device's model field so
+ * that the software components which uses IPU driver can get the hw stepping
+ * information.
+ */
+#define IPU_MEDIA_DEV_MODEL_NAME		"ipu6"
+
+#define IPU6SE_ISYS_NUM_STREAMS          IPU6SE_NONSECURE_STREAM_ID_MAX
+#define IPU6_ISYS_NUM_STREAMS            IPU6_NONSECURE_STREAM_ID_MAX
+
+/* declearations, definitions in ipu6.c */
+extern struct ipu_isys_internal_pdata isys_ipdata;
+extern struct ipu_psys_internal_pdata psys_ipdata;
+extern const struct ipu_buttress_ctrl isys_buttress_ctrl;
+extern const struct ipu_buttress_ctrl psys_buttress_ctrl;
+
+/* definitions in ipu6-isys.c */
+extern struct ipu_trace_block isys_trace_blocks[];
+/* definitions in ipu6-psys.c */
+extern struct ipu_trace_block psys_trace_blocks[];
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu-resources.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu-resources.c
@@ -0,0 +1,860 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2015 - 2020 Intel Corporation
+
+#include <linux/bitmap.h>
+#include <linux/errno.h>
+#include <linux/gfp.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+
+#include <uapi/linux/ipu-psys.h>
+
+#include "ipu-fw-psys.h"
+#include "ipu-psys.h"
+
+struct ipu6_psys_hw_res_variant hw_var;
+void ipu6_psys_hw_res_variant_init(void)
+{
+	if (ipu_ver == IPU_VER_6SE) {
+		hw_var.queue_num = IPU6SE_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+		hw_var.cell_num = IPU6SE_FW_PSYS_N_CELL_ID;
+	} else if (ipu_ver == IPU_VER_6) {
+		hw_var.queue_num = IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+		hw_var.cell_num = IPU6_FW_PSYS_N_CELL_ID;
+	} else if (ipu_ver == IPU_VER_6EP) {
+		hw_var.queue_num = IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+		hw_var.cell_num = IPU6EP_FW_PSYS_N_CELL_ID;
+	} else {
+		WARN(1, "ipu6 psys res var is not initialised correctly.");
+	}
+
+	hw_var.set_proc_dev_chn = ipu6_fw_psys_set_proc_dev_chn;
+	hw_var.set_proc_dfm_bitmap = ipu6_fw_psys_set_proc_dfm_bitmap;
+	hw_var.set_proc_ext_mem = ipu6_fw_psys_set_process_ext_mem;
+	hw_var.get_pgm_by_proc =
+		ipu6_fw_psys_get_program_manifest_by_process;
+	return;
+}
+
+static const struct ipu_fw_resource_definitions *get_res(void)
+{
+	if (ipu_ver == IPU_VER_6SE)
+		return ipu6se_res_defs;
+
+	if (ipu_ver == IPU_VER_6EP)
+		return ipu6ep_res_defs;
+
+	return ipu6_res_defs;
+}
+
+static int ipu_resource_init(struct ipu_resource *res, u32 id, int elements)
+{
+	if (elements <= 0) {
+		res->bitmap = NULL;
+		return 0;
+	}
+
+	res->bitmap = bitmap_zalloc(elements, GFP_KERNEL);
+	if (!res->bitmap)
+		return -ENOMEM;
+	res->elements = elements;
+	res->id = id;
+	return 0;
+}
+
+static unsigned long
+ipu_resource_alloc_with_pos(struct ipu_resource *res, int n,
+			    int pos,
+			    struct ipu_resource_alloc *alloc,
+			    enum ipu_resource_type type)
+{
+	unsigned long p;
+
+	if (n <= 0) {
+		alloc->elements = 0;
+		return 0;
+	}
+
+	if (!res->bitmap || pos >= res->elements)
+		return (unsigned long)(-ENOSPC);
+
+	p = bitmap_find_next_zero_area(res->bitmap, res->elements, pos, n, 0);
+	alloc->resource = NULL;
+
+	if (p != pos)
+		return (unsigned long)(-ENOSPC);
+	bitmap_set(res->bitmap, p, n);
+	alloc->resource = res;
+	alloc->elements = n;
+	alloc->pos = p;
+	alloc->type = type;
+
+	return pos;
+}
+
+static unsigned long
+ipu_resource_alloc(struct ipu_resource *res, int n,
+		   struct ipu_resource_alloc *alloc,
+		   enum ipu_resource_type type)
+{
+	unsigned long p;
+
+	if (n <= 0) {
+		alloc->elements = 0;
+		return 0;
+	}
+
+	if (!res->bitmap)
+		return (unsigned long)(-ENOSPC);
+
+	p = bitmap_find_next_zero_area(res->bitmap, res->elements, 0, n, 0);
+	alloc->resource = NULL;
+
+	if (p >= res->elements)
+		return (unsigned long)(-ENOSPC);
+	bitmap_set(res->bitmap, p, n);
+	alloc->resource = res;
+	alloc->elements = n;
+	alloc->pos = p;
+	alloc->type = type;
+
+	return p;
+}
+
+static void ipu_resource_free(struct ipu_resource_alloc *alloc)
+{
+	if (alloc->elements <= 0)
+		return;
+
+	if (alloc->type == IPU_RESOURCE_DFM)
+		*alloc->resource->bitmap &= ~(unsigned long)(alloc->elements);
+	else
+		bitmap_clear(alloc->resource->bitmap, alloc->pos,
+			     alloc->elements);
+	alloc->resource = NULL;
+}
+
+static void ipu_resource_cleanup(struct ipu_resource *res)
+{
+	bitmap_free(res->bitmap);
+	res->bitmap = NULL;
+}
+
+/********** IPU PSYS-specific resource handling **********/
+int ipu_psys_resource_pool_init(struct ipu_psys_resource_pool *pool)
+{
+	int i, j, k, ret;
+	const struct ipu_fw_resource_definitions *res_defs;
+
+	res_defs = get_res();
+
+	spin_lock_init(&pool->queues_lock);
+	pool->cells = 0;
+
+	for (i = 0; i < res_defs->num_dev_channels; i++) {
+		ret = ipu_resource_init(&pool->dev_channels[i], i,
+					res_defs->dev_channels[i]);
+		if (ret)
+			goto error;
+	}
+
+	for (j = 0; j < res_defs->num_ext_mem_ids; j++) {
+		ret = ipu_resource_init(&pool->ext_memory[j], j,
+					res_defs->ext_mem_ids[j]);
+		if (ret)
+			goto memory_error;
+	}
+
+	for (k = 0; k < res_defs->num_dfm_ids; k++) {
+		ret = ipu_resource_init(&pool->dfms[k], k, res_defs->dfms[k]);
+		if (ret)
+			goto dfm_error;
+	}
+
+	spin_lock(&pool->queues_lock);
+	if (ipu_ver == IPU_VER_6SE)
+		bitmap_zero(pool->cmd_queues,
+			    IPU6SE_FW_PSYS_N_PSYS_CMD_QUEUE_ID);
+	else
+		bitmap_zero(pool->cmd_queues,
+			    IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID);
+	spin_unlock(&pool->queues_lock);
+
+	return 0;
+
+dfm_error:
+	for (k--; k >= 0; k--)
+		ipu_resource_cleanup(&pool->dfms[k]);
+
+memory_error:
+	for (j--; j >= 0; j--)
+		ipu_resource_cleanup(&pool->ext_memory[j]);
+
+error:
+	for (i--; i >= 0; i--)
+		ipu_resource_cleanup(&pool->dev_channels[i]);
+	return ret;
+}
+
+void ipu_psys_resource_copy(struct ipu_psys_resource_pool *src,
+			    struct ipu_psys_resource_pool *dest)
+{
+	int i;
+	const struct ipu_fw_resource_definitions *res_defs;
+
+	res_defs = get_res();
+
+	dest->cells = src->cells;
+	for (i = 0; i < res_defs->num_dev_channels; i++)
+		*dest->dev_channels[i].bitmap = *src->dev_channels[i].bitmap;
+
+	for (i = 0; i < res_defs->num_ext_mem_ids; i++)
+		*dest->ext_memory[i].bitmap = *src->ext_memory[i].bitmap;
+
+	for (i = 0; i < res_defs->num_dfm_ids; i++)
+		*dest->dfms[i].bitmap = *src->dfms[i].bitmap;
+}
+
+void ipu_psys_resource_pool_cleanup(struct ipu_psys_resource_pool
+				    *pool)
+{
+	u32 i;
+	const struct ipu_fw_resource_definitions *res_defs;
+
+	res_defs = get_res();
+	for (i = 0; i < res_defs->num_dev_channels; i++)
+		ipu_resource_cleanup(&pool->dev_channels[i]);
+
+	for (i = 0; i < res_defs->num_ext_mem_ids; i++)
+		ipu_resource_cleanup(&pool->ext_memory[i]);
+
+	for (i = 0; i < res_defs->num_dfm_ids; i++)
+		ipu_resource_cleanup(&pool->dfms[i]);
+}
+
+static int __alloc_one_resrc(const struct device *dev,
+			     struct ipu_fw_psys_process *process,
+			     struct ipu_resource *resource,
+			     struct ipu_fw_generic_program_manifest *pm,
+			     u32 resource_id,
+			     struct ipu_psys_resource_alloc *alloc)
+{
+	const u16 resource_req = pm->dev_chn_size[resource_id];
+	const u16 resource_offset_req = pm->dev_chn_offset[resource_id];
+	unsigned long retl;
+
+	if (resource_req <= 0)
+		return -ENXIO;
+
+	if (alloc->resources >= IPU_MAX_RESOURCES) {
+		dev_err(dev, "out of resource handles\n");
+		return -ENOSPC;
+	}
+	if (resource_offset_req != (u16)(-1))
+		retl = ipu_resource_alloc_with_pos
+		    (resource,
+		     resource_req,
+		     resource_offset_req,
+		     &alloc->resource_alloc[alloc->resources],
+		     IPU_RESOURCE_DEV_CHN);
+	else
+		retl = ipu_resource_alloc
+		    (resource, resource_req,
+		     &alloc->resource_alloc[alloc->resources],
+		     IPU_RESOURCE_DEV_CHN);
+	if (IS_ERR_VALUE(retl)) {
+		dev_dbg(dev, "out of device channel resources\n");
+		return (int)retl;
+	}
+	alloc->resources++;
+
+	return 0;
+}
+
+static int ipu_psys_allocate_one_dfm(const struct device *dev,
+				     struct ipu_fw_psys_process *process,
+				     struct ipu_resource *resource,
+				     struct ipu_fw_generic_program_manifest *pm,
+				     u32 resource_id,
+				     struct ipu_psys_resource_alloc *alloc)
+{
+	u32 dfm_bitmap_req = pm->dfm_port_bitmap[resource_id];
+	u32 active_dfm_bitmap_req = pm->dfm_active_port_bitmap[resource_id];
+	const u8 is_relocatable = pm->is_dfm_relocatable[resource_id];
+	struct ipu_resource_alloc *alloc_resource;
+	unsigned long p = 0;
+
+	if (dfm_bitmap_req == 0)
+		return -ENXIO;
+
+	if (alloc->resources >= IPU_MAX_RESOURCES) {
+		dev_err(dev, "out of resource handles\n");
+		return -ENOSPC;
+	}
+
+	if (!resource->bitmap)
+		return -ENOSPC;
+
+	if (!is_relocatable) {
+		if (*resource->bitmap & dfm_bitmap_req) {
+			dev_warn(dev,
+				 "out of dfm resources, req 0x%x, get 0x%lx\n",
+				 dfm_bitmap_req, *resource->bitmap);
+			return -ENOSPC;
+		}
+		*resource->bitmap |= dfm_bitmap_req;
+	} else {
+		unsigned int n = hweight32(dfm_bitmap_req);
+
+		p = bitmap_find_next_zero_area(resource->bitmap,
+					       resource->elements, 0, n, 0);
+
+		if (p >= resource->elements)
+			return -ENOSPC;
+
+		bitmap_set(resource->bitmap, p, n);
+		dfm_bitmap_req = dfm_bitmap_req << p;
+		active_dfm_bitmap_req = active_dfm_bitmap_req << p;
+	}
+
+	alloc_resource = &alloc->resource_alloc[alloc->resources];
+	alloc_resource->resource = resource;
+	/* Using elements to indicate the bitmap */
+	alloc_resource->elements = dfm_bitmap_req;
+	alloc_resource->pos = p;
+	alloc_resource->type = IPU_RESOURCE_DFM;
+
+	alloc->resources++;
+
+	return 0;
+}
+
+/*
+ * ext_mem_type_id is a generic type id for memory (like DMEM, VMEM)
+ * ext_mem_bank_id is detailed type id for  memory (like DMEM0, DMEM1 etc.)
+ */
+static int __alloc_mem_resrc(const struct device *dev,
+			     struct ipu_fw_psys_process *process,
+			     struct ipu_resource *resource,
+			     struct ipu_fw_generic_program_manifest *pm,
+			     u32 ext_mem_type_id, u32 ext_mem_bank_id,
+			     struct ipu_psys_resource_alloc *alloc)
+{
+	const u16 memory_resource_req = pm->ext_mem_size[ext_mem_type_id];
+	const u16 memory_offset_req = pm->ext_mem_offset[ext_mem_type_id];
+
+	unsigned long retl;
+
+	if (memory_resource_req <= 0)
+		return -ENXIO;
+
+	if (alloc->resources >= IPU_MAX_RESOURCES) {
+		dev_err(dev, "out of resource handles\n");
+		return -ENOSPC;
+	}
+	if (memory_offset_req != (u16)(-1))
+		retl = ipu_resource_alloc_with_pos
+		    (resource,
+		     memory_resource_req, memory_offset_req,
+		     &alloc->resource_alloc[alloc->resources],
+		     IPU_RESOURCE_EXT_MEM);
+	else
+		retl = ipu_resource_alloc
+		    (resource, memory_resource_req,
+		     &alloc->resource_alloc[alloc->resources],
+		     IPU_RESOURCE_EXT_MEM);
+	if (IS_ERR_VALUE(retl)) {
+		dev_dbg(dev, "out of memory resources\n");
+		return (int)retl;
+	}
+
+	alloc->resources++;
+
+	return 0;
+}
+
+int ipu_psys_allocate_cmd_queue_resource(struct ipu_psys_resource_pool *pool)
+{
+	unsigned long p;
+	int size, start;
+
+	size = IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+	start = IPU6_FW_PSYS_CMD_QUEUE_PPG0_COMMAND_ID;
+
+	if (ipu_ver == IPU_VER_6SE) {
+		size = IPU6SE_FW_PSYS_N_PSYS_CMD_QUEUE_ID;
+		start = IPU6SE_FW_PSYS_CMD_QUEUE_PPG0_COMMAND_ID;
+	}
+
+	spin_lock(&pool->queues_lock);
+	/* find available cmd queue from ppg0_cmd_id */
+	p = bitmap_find_next_zero_area(pool->cmd_queues, size, start, 1, 0);
+
+	if (p >= size) {
+		spin_unlock(&pool->queues_lock);
+		return -ENOSPC;
+	}
+
+	bitmap_set(pool->cmd_queues, p, 1);
+	spin_unlock(&pool->queues_lock);
+
+	return p;
+}
+
+void ipu_psys_free_cmd_queue_resource(struct ipu_psys_resource_pool *pool,
+				      u8 queue_id)
+{
+	spin_lock(&pool->queues_lock);
+	bitmap_clear(pool->cmd_queues, queue_id, 1);
+	spin_unlock(&pool->queues_lock);
+}
+
+int ipu_psys_try_allocate_resources(struct device *dev,
+				    struct ipu_fw_psys_process_group *pg,
+				    void *pg_manifest,
+				    struct ipu_psys_resource_pool *pool)
+{
+	u32 id, idx;
+	u32 mem_type_id;
+	int ret, i;
+	u16 *process_offset_table;
+	u8 processes;
+	u32 cells = 0;
+	struct ipu_psys_resource_alloc *alloc;
+	const struct ipu_fw_resource_definitions *res_defs;
+
+	if (!pg)
+		return -EINVAL;
+	process_offset_table = (u16 *)((u8 *)pg + pg->processes_offset);
+	processes = pg->process_count;
+
+	alloc = kzalloc(sizeof(*alloc), GFP_KERNEL);
+	if (!alloc)
+		return -ENOMEM;
+
+	res_defs = get_res();
+	for (i = 0; i < processes; i++) {
+		u32 cell;
+		struct ipu_fw_psys_process *process =
+			(struct ipu_fw_psys_process *)
+			((char *)pg + process_offset_table[i]);
+		struct ipu_fw_generic_program_manifest pm;
+
+		memset(&pm, 0, sizeof(pm));
+
+		if (!process) {
+			dev_err(dev, "can not get process\n");
+			ret = -ENOENT;
+			goto free_out;
+		}
+
+		ret = ipu_fw_psys_get_program_manifest_by_process
+			(&pm, pg_manifest, process);
+		if (ret < 0) {
+			dev_err(dev, "can not get manifest\n");
+			goto free_out;
+		}
+
+		if (pm.cell_id == res_defs->num_cells &&
+		    pm.cell_type_id == res_defs->num_cells_type) {
+			cell = res_defs->num_cells;
+		} else if ((pm.cell_id != res_defs->num_cells &&
+			    pm.cell_type_id == res_defs->num_cells_type)) {
+			cell = pm.cell_id;
+		} else {
+			/* Find a free cell of desired type */
+			u32 type = pm.cell_type_id;
+
+			for (cell = 0; cell < res_defs->num_cells; cell++)
+				if (res_defs->cells[cell] == type &&
+				    ((pool->cells | cells) & (1 << cell)) == 0)
+					break;
+			if (cell >= res_defs->num_cells) {
+				dev_dbg(dev, "no free cells of right type\n");
+				ret = -ENOSPC;
+				goto free_out;
+			}
+		}
+		if (cell < res_defs->num_cells)
+			cells |= 1 << cell;
+		if (pool->cells & cells) {
+			dev_dbg(dev, "out of cell resources\n");
+			ret = -ENOSPC;
+			goto free_out;
+		}
+
+		if (pm.dev_chn_size) {
+			for (id = 0; id < res_defs->num_dev_channels; id++) {
+				ret = __alloc_one_resrc(dev, process,
+							&pool->dev_channels[id],
+							&pm, id, alloc);
+				if (ret && ret != -ENXIO)
+					goto free_out;
+			}
+		}
+
+		if (pm.dfm_port_bitmap) {
+			for (id = 0; id < res_defs->num_dfm_ids; id++) {
+				ret = ipu_psys_allocate_one_dfm
+					(dev, process,
+					 &pool->dfms[id], &pm, id, alloc);
+				if (ret && ret != -ENXIO)
+					goto free_out;
+			}
+		}
+
+		if (pm.ext_mem_size) {
+			for (mem_type_id = 0;
+			     mem_type_id < res_defs->num_ext_mem_types;
+			     mem_type_id++) {
+				u32 bank = res_defs->num_ext_mem_ids;
+
+				if (cell != res_defs->num_cells) {
+					idx = res_defs->cell_mem_row * cell +
+						mem_type_id;
+					bank = res_defs->cell_mem[idx];
+				}
+
+				if (bank == res_defs->num_ext_mem_ids)
+					continue;
+
+				ret = __alloc_mem_resrc(dev, process,
+							&pool->ext_memory[bank],
+							&pm, mem_type_id, bank,
+							alloc);
+				if (ret && ret != -ENXIO)
+					goto free_out;
+			}
+		}
+	}
+	alloc->cells |= cells;
+	pool->cells |= cells;
+
+	kfree(alloc);
+	return 0;
+
+free_out:
+	dev_dbg(dev, "failed to try_allocate resource\n");
+	kfree(alloc);
+	return ret;
+}
+
+/*
+ * Allocate resources for pg from `pool'. Mark the allocated
+ * resources into `alloc'. Returns 0 on success, -ENOSPC
+ * if there are no enough resources, in which cases resources
+ * are not allocated at all, or some other error on other conditions.
+ */
+int ipu_psys_allocate_resources(const struct device *dev,
+				struct ipu_fw_psys_process_group *pg,
+				void *pg_manifest,
+				struct ipu_psys_resource_alloc
+				*alloc, struct ipu_psys_resource_pool
+				*pool)
+{
+	u32 id;
+	u32 mem_type_id;
+	int ret, i;
+	u16 *process_offset_table;
+	u8 processes;
+	u32 cells = 0;
+	int p, idx;
+	u32 bmp, a_bmp;
+	const struct ipu_fw_resource_definitions *res_defs;
+
+	if (!pg)
+		return -EINVAL;
+
+	res_defs = get_res();
+	process_offset_table = (u16 *)((u8 *)pg + pg->processes_offset);
+	processes = pg->process_count;
+
+	for (i = 0; i < processes; i++) {
+		u32 cell;
+		struct ipu_fw_psys_process *process =
+		    (struct ipu_fw_psys_process *)
+		    ((char *)pg + process_offset_table[i]);
+		struct ipu_fw_generic_program_manifest pm;
+
+		memset(&pm, 0, sizeof(pm));
+		if (!process) {
+			dev_err(dev, "can not get process\n");
+			ret = -ENOENT;
+			goto free_out;
+		}
+
+		ret = ipu_fw_psys_get_program_manifest_by_process
+		    (&pm, pg_manifest, process);
+		if (ret < 0) {
+			dev_err(dev, "can not get manifest\n");
+			goto free_out;
+		}
+
+		if (pm.cell_id == res_defs->num_cells &&
+		    pm.cell_type_id == res_defs->num_cells_type) {
+			cell = res_defs->num_cells;
+		} else if ((pm.cell_id != res_defs->num_cells &&
+			    pm.cell_type_id == res_defs->num_cells_type)) {
+			cell = pm.cell_id;
+		} else {
+			/* Find a free cell of desired type */
+			u32 type = pm.cell_type_id;
+
+			for (cell = 0; cell < res_defs->num_cells; cell++)
+				if (res_defs->cells[cell] == type &&
+				    ((pool->cells | cells) & (1 << cell)) == 0)
+					break;
+			if (cell >= res_defs->num_cells) {
+				dev_dbg(dev, "no free cells of right type\n");
+				ret = -ENOSPC;
+				goto free_out;
+			}
+			ret = ipu_fw_psys_set_process_cell_id(process, 0, cell);
+			if (ret)
+				goto free_out;
+		}
+		if (cell < res_defs->num_cells)
+			cells |= 1 << cell;
+		if (pool->cells & cells) {
+			dev_dbg(dev, "out of cell resources\n");
+			ret = -ENOSPC;
+			goto free_out;
+		}
+
+		if (pm.dev_chn_size) {
+			for (id = 0; id < res_defs->num_dev_channels; id++) {
+				ret = __alloc_one_resrc(dev, process,
+							&pool->dev_channels[id],
+							&pm, id, alloc);
+				if (ret == -ENXIO)
+					continue;
+
+				if (ret)
+					goto free_out;
+
+				idx = alloc->resources - 1;
+				p = alloc->resource_alloc[idx].pos;
+				ret = ipu_fw_psys_set_proc_dev_chn(process, id,
+								   p);
+				if (ret)
+					goto free_out;
+			}
+		}
+
+		if (pm.dfm_port_bitmap) {
+			for (id = 0; id < res_defs->num_dfm_ids; id++) {
+				ret = ipu_psys_allocate_one_dfm(dev, process,
+								&pool->dfms[id],
+								&pm, id, alloc);
+				if (ret == -ENXIO)
+					continue;
+
+				if (ret)
+					goto free_out;
+
+				idx = alloc->resources - 1;
+				p = alloc->resource_alloc[idx].pos;
+				bmp = pm.dfm_port_bitmap[id];
+				bmp = bmp << p;
+				a_bmp = pm.dfm_active_port_bitmap[id];
+				a_bmp = a_bmp << p;
+				ret = ipu_fw_psys_set_proc_dfm_bitmap(process,
+								      id, bmp,
+								      a_bmp);
+				if (ret)
+					goto free_out;
+			}
+		}
+
+		if (pm.ext_mem_size) {
+			for (mem_type_id = 0;
+			     mem_type_id < res_defs->num_ext_mem_types;
+			     mem_type_id++) {
+				u32 bank = res_defs->num_ext_mem_ids;
+
+				if (cell != res_defs->num_cells) {
+					idx = res_defs->cell_mem_row * cell +
+						mem_type_id;
+					bank = res_defs->cell_mem[idx];
+				}
+				if (bank == res_defs->num_ext_mem_ids)
+					continue;
+
+				ret = __alloc_mem_resrc(dev, process,
+							&pool->ext_memory[bank],
+							&pm, mem_type_id,
+							bank, alloc);
+				if (ret == -ENXIO)
+					continue;
+
+				if (ret)
+					goto free_out;
+
+				/* no return value check here because fw api
+				 * will do some checks, and would return
+				 * non-zero except mem_type_id == 0.
+				 * This maybe caused by that above flow of
+				 * allocating mem_bank_id is improper.
+				 */
+				idx = alloc->resources - 1;
+				p = alloc->resource_alloc[idx].pos;
+				ipu_fw_psys_set_process_ext_mem(process,
+								mem_type_id,
+								bank, p);
+			}
+		}
+	}
+	alloc->cells |= cells;
+	pool->cells |= cells;
+	return 0;
+
+free_out:
+	dev_err(dev, "failed to allocate resources, ret %d\n", ret);
+	ipu_psys_reset_process_cell(dev, pg, pg_manifest, i + 1);
+	ipu_psys_free_resources(alloc, pool);
+	return ret;
+}
+
+int ipu_psys_move_resources(const struct device *dev,
+			    struct ipu_psys_resource_alloc *alloc,
+			    struct ipu_psys_resource_pool
+			    *source_pool, struct ipu_psys_resource_pool
+			    *target_pool)
+{
+	int i;
+
+	if (target_pool->cells & alloc->cells) {
+		dev_dbg(dev, "out of cell resources\n");
+		return -ENOSPC;
+	}
+
+	for (i = 0; i < alloc->resources; i++) {
+		unsigned long bitmap = 0;
+		unsigned int id = alloc->resource_alloc[i].resource->id;
+		unsigned long fbit, end;
+
+		switch (alloc->resource_alloc[i].type) {
+		case IPU_RESOURCE_DEV_CHN:
+			bitmap_set(&bitmap, alloc->resource_alloc[i].pos,
+				   alloc->resource_alloc[i].elements);
+			if (*target_pool->dev_channels[id].bitmap & bitmap)
+				return -ENOSPC;
+			break;
+		case IPU_RESOURCE_EXT_MEM:
+			end = alloc->resource_alloc[i].elements +
+			    alloc->resource_alloc[i].pos;
+
+			fbit = find_next_bit(target_pool->ext_memory[id].bitmap,
+					     end, alloc->resource_alloc[i].pos);
+			/* if find_next_bit returns "end" it didn't find 1bit */
+			if (end != fbit)
+				return -ENOSPC;
+			break;
+		case IPU_RESOURCE_DFM:
+			bitmap = alloc->resource_alloc[i].elements;
+			if (*target_pool->dfms[id].bitmap & bitmap)
+				return -ENOSPC;
+			break;
+		default:
+			dev_err(dev, "Illegal resource type\n");
+			return -EINVAL;
+		}
+	}
+
+	for (i = 0; i < alloc->resources; i++) {
+		u32 id = alloc->resource_alloc[i].resource->id;
+
+		switch (alloc->resource_alloc[i].type) {
+		case IPU_RESOURCE_DEV_CHN:
+			bitmap_set(target_pool->dev_channels[id].bitmap,
+				   alloc->resource_alloc[i].pos,
+				   alloc->resource_alloc[i].elements);
+			ipu_resource_free(&alloc->resource_alloc[i]);
+			alloc->resource_alloc[i].resource =
+			    &target_pool->dev_channels[id];
+			break;
+		case IPU_RESOURCE_EXT_MEM:
+			bitmap_set(target_pool->ext_memory[id].bitmap,
+				   alloc->resource_alloc[i].pos,
+				   alloc->resource_alloc[i].elements);
+			ipu_resource_free(&alloc->resource_alloc[i]);
+			alloc->resource_alloc[i].resource =
+			    &target_pool->ext_memory[id];
+			break;
+		case IPU_RESOURCE_DFM:
+			*target_pool->dfms[id].bitmap |=
+			    alloc->resource_alloc[i].elements;
+			*alloc->resource_alloc[i].resource->bitmap &=
+			    ~(alloc->resource_alloc[i].elements);
+			alloc->resource_alloc[i].resource =
+			    &target_pool->dfms[id];
+			break;
+		default:
+			/*
+			 * Just keep compiler happy. This case failed already
+			 * in above loop.
+			 */
+			break;
+		}
+	}
+
+	target_pool->cells |= alloc->cells;
+	source_pool->cells &= ~alloc->cells;
+
+	return 0;
+}
+
+void ipu_psys_reset_process_cell(const struct device *dev,
+				 struct ipu_fw_psys_process_group *pg,
+				 void *pg_manifest,
+				 int process_count)
+{
+	int i;
+	u16 *process_offset_table;
+	const struct ipu_fw_resource_definitions *res_defs;
+
+	if (!pg)
+		return;
+
+	res_defs = get_res();
+	process_offset_table = (u16 *)((u8 *)pg + pg->processes_offset);
+	for (i = 0; i < process_count; i++) {
+		struct ipu_fw_psys_process *process =
+		    (struct ipu_fw_psys_process *)
+		    ((char *)pg + process_offset_table[i]);
+		struct ipu_fw_generic_program_manifest pm;
+		int ret;
+
+		if (!process)
+			break;
+
+		ret = ipu_fw_psys_get_program_manifest_by_process(&pm,
+								  pg_manifest,
+								  process);
+		if (ret < 0) {
+			dev_err(dev, "can not get manifest\n");
+			break;
+		}
+		if ((pm.cell_id != res_defs->num_cells &&
+		     pm.cell_type_id == res_defs->num_cells_type))
+			continue;
+		/* no return value check here because if finding free cell
+		 * failed, process cell would not set then calling clear_cell
+		 * will return non-zero.
+		 */
+		ipu_fw_psys_clear_process_cell(process);
+	}
+}
+
+/* Free resources marked in `alloc' from `resources' */
+void ipu_psys_free_resources(struct ipu_psys_resource_alloc
+			     *alloc, struct ipu_psys_resource_pool *pool)
+{
+	unsigned int i;
+
+	pool->cells &= ~alloc->cells;
+	alloc->cells = 0;
+	for (i = 0; i < alloc->resources; i++)
+		ipu_resource_free(&alloc->resource_alloc[i]);
+	alloc->resources = 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-fw-resources.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-fw-resources.c
@@ -0,0 +1,608 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2015 - 2021 Intel Corporation
+
+#include <linux/err.h>
+#include <linux/string.h>
+
+#include "ipu-psys.h"
+#include "ipu-fw-psys.h"
+#include "ipu6-platform-resources.h"
+
+/* resources table */
+
+/*
+ * Cell types by cell IDs
+ */
+static const u8 ipu6_fw_psys_cell_types[IPU6_FW_PSYS_N_CELL_ID] = {
+	IPU6_FW_PSYS_SP_CTRL_TYPE_ID,
+	IPU6_FW_PSYS_VP_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* X2B_MD */
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* ICA_MEDIUM */
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* X2B_SVE_RGBIR */
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* PAF */
+	IPU6_FW_PSYS_GDC_TYPE_ID,
+	IPU6_FW_PSYS_TNR_TYPE_ID,
+};
+
+static const u16 ipu6_fw_num_dev_channels[IPU6_FW_PSYS_N_DEV_CHN_ID] = {
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT0_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_READ_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_INTERNAL_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_ISA_MAX_SIZE,
+};
+
+static const u16 ipu6_fw_psys_mem_size[IPU6_FW_PSYS_N_MEM_ID] = {
+	IPU6_FW_PSYS_VMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_TRANSFER_VMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_TRANSFER_VMEM1_MAX_SIZE,
+	IPU6_FW_PSYS_LB_VMEM_MAX_SIZE,
+	IPU6_FW_PSYS_BAMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM1_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM2_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM3_MAX_SIZE,
+	IPU6_FW_PSYS_PMEM0_MAX_SIZE
+};
+
+static const u16 ipu6_fw_psys_dfms[IPU6_FW_PSYS_N_DEV_DFM_ID] = {
+	IPU6_FW_PSYS_DEV_DFM_BB_FULL_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_BB_EMPTY_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_LB_FULL_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_LB_EMPTY_PORT_ID_MAX_SIZE,
+};
+
+static const u8
+ipu6_fw_psys_c_mem[IPU6_FW_PSYS_N_CELL_ID][IPU6_FW_PSYS_N_MEM_TYPE_ID] = {
+	{
+		/* IPU6_FW_PSYS_SP0_ID */
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_DMEM0_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_SP1_ID */
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_DMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_VP0_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_DMEM3_ID,
+		IPU6_FW_PSYS_VMEM0_ID,
+		IPU6_FW_PSYS_BAMEM0_ID,
+		IPU6_FW_PSYS_PMEM0_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC1_ID BNLM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC2_ID DM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC3_ID ACM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC4_ID GTC YUV1 */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC5_ID OFS pin main */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC6_ID OFS pin display */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC7_ID OFS pin pp */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC8_ID GAMMASTAR */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC9_ID GLTM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC10_ID XNR */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_ICA_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_LSC_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_DPC_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_SIS_A_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_SIS_B_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_B2B_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_B2R_ID and ISA_R2I_SIE */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_R2I_DS_A_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_R2I_DS_B_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_AWB_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_AE_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_AF_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_DOL_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_X2B_MD_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_ICA_MEDIUM_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_X2B_SVE_RGBIR_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_PAF_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_BB_ACC_GDC0_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_BB_ACC_TNR_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	}
+};
+
+static const struct ipu_fw_resource_definitions ipu6_defs = {
+	.cells = ipu6_fw_psys_cell_types,
+	.num_cells = IPU6_FW_PSYS_N_CELL_ID,
+	.num_cells_type = IPU6_FW_PSYS_N_CELL_TYPE_ID,
+
+	.dev_channels = ipu6_fw_num_dev_channels,
+	.num_dev_channels = IPU6_FW_PSYS_N_DEV_CHN_ID,
+
+	.num_ext_mem_types = IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID,
+	.num_ext_mem_ids = IPU6_FW_PSYS_N_MEM_ID,
+	.ext_mem_ids = ipu6_fw_psys_mem_size,
+
+	.num_dfm_ids = IPU6_FW_PSYS_N_DEV_DFM_ID,
+
+	.dfms = ipu6_fw_psys_dfms,
+
+	.cell_mem_row = IPU6_FW_PSYS_N_MEM_TYPE_ID,
+	.cell_mem = &ipu6_fw_psys_c_mem[0][0],
+};
+
+const struct ipu_fw_resource_definitions *ipu6_res_defs = &ipu6_defs;
+
+/********** Generic resource handling **********/
+
+int ipu6_fw_psys_set_proc_dev_chn(struct ipu_fw_psys_process *ptr, u16 offset,
+				  u16 value)
+{
+	struct ipu6_fw_psys_process_ext *pm_ext;
+	u8 ps_ext_offset;
+
+	ps_ext_offset = ptr->process_extension_offset;
+	if (!ps_ext_offset)
+		return -EINVAL;
+
+	pm_ext = (struct ipu6_fw_psys_process_ext *)((u8 *)ptr + ps_ext_offset);
+
+	pm_ext->dev_chn_offset[offset] = value;
+
+	return 0;
+}
+
+int ipu6_fw_psys_set_proc_dfm_bitmap(struct ipu_fw_psys_process *ptr,
+				     u16 id, u32 bitmap,
+				     u32 active_bitmap)
+{
+	struct ipu6_fw_psys_process_ext *pm_ext;
+	u8 ps_ext_offset;
+
+	ps_ext_offset = ptr->process_extension_offset;
+	if (!ps_ext_offset)
+		return -EINVAL;
+
+	pm_ext = (struct ipu6_fw_psys_process_ext *)((u8 *)ptr + ps_ext_offset);
+
+	pm_ext->dfm_port_bitmap[id] = bitmap;
+	pm_ext->dfm_active_port_bitmap[id] = active_bitmap;
+
+	return 0;
+}
+
+int ipu6_fw_psys_set_process_ext_mem(struct ipu_fw_psys_process *ptr,
+				     u16 type_id, u16 mem_id, u16 offset)
+{
+	struct ipu6_fw_psys_process_ext *pm_ext;
+	u8 ps_ext_offset;
+
+	ps_ext_offset = ptr->process_extension_offset;
+	if (!ps_ext_offset)
+		return -EINVAL;
+
+	pm_ext = (struct ipu6_fw_psys_process_ext *)((u8 *)ptr + ps_ext_offset);
+
+	pm_ext->ext_mem_offset[type_id] = offset;
+	pm_ext->ext_mem_id[type_id] = mem_id;
+
+	return 0;
+}
+
+static struct ipu_fw_psys_program_manifest *
+get_program_manifest(const struct ipu_fw_psys_program_group_manifest *manifest,
+		     const unsigned int program_index)
+{
+	struct ipu_fw_psys_program_manifest *prg_manifest_base;
+	u8 *program_manifest = NULL;
+	u8 program_count;
+	unsigned int i;
+
+	program_count = manifest->program_count;
+
+	prg_manifest_base = (struct ipu_fw_psys_program_manifest *)
+		((char *)manifest + manifest->program_manifest_offset);
+	if (program_index < program_count) {
+		program_manifest = (u8 *)prg_manifest_base;
+		for (i = 0; i < program_index; i++)
+			program_manifest +=
+				((struct ipu_fw_psys_program_manifest *)
+				 program_manifest)->size;
+	}
+
+	return (struct ipu_fw_psys_program_manifest *)program_manifest;
+}
+
+int ipu6_fw_psys_get_program_manifest_by_process(
+	struct ipu_fw_generic_program_manifest *gen_pm,
+	const struct ipu_fw_psys_program_group_manifest *pg_manifest,
+	struct ipu_fw_psys_process *process)
+{
+	u32 program_id = process->program_idx;
+	struct ipu_fw_psys_program_manifest *pm;
+	struct ipu6_fw_psys_program_manifest_ext *pm_ext;
+
+	pm = get_program_manifest(pg_manifest, program_id);
+
+	if (!pm)
+		return -ENOENT;
+
+	if (pm->program_extension_offset) {
+		pm_ext = (struct ipu6_fw_psys_program_manifest_ext *)
+			((u8 *)pm + pm->program_extension_offset);
+
+		gen_pm->dev_chn_size = pm_ext->dev_chn_size;
+		gen_pm->dev_chn_offset = pm_ext->dev_chn_offset;
+		gen_pm->ext_mem_size = pm_ext->ext_mem_size;
+		gen_pm->ext_mem_offset = (u16 *)pm_ext->ext_mem_offset;
+		gen_pm->is_dfm_relocatable = pm_ext->is_dfm_relocatable;
+		gen_pm->dfm_port_bitmap = pm_ext->dfm_port_bitmap;
+		gen_pm->dfm_active_port_bitmap =
+			pm_ext->dfm_active_port_bitmap;
+	}
+
+	memcpy(gen_pm->cells, pm->cells, sizeof(pm->cells));
+	gen_pm->cell_id = pm->cells[0];
+	gen_pm->cell_type_id = pm->cell_type_id;
+
+	return 0;
+}
+
+#if defined(DEBUG) || defined(CONFIG_DYNAMIC_DEBUG) || \
+	(defined(CONFIG_DYNAMIC_DEBUG_CORE) && defined(DYNAMIC_DEBUG_MODULE))
+void ipu6_fw_psys_pg_dump(struct ipu_psys *psys,
+			  struct ipu_psys_kcmd *kcmd, const char *note)
+{
+	struct ipu_fw_psys_process_group *pg = kcmd->kpg->pg;
+	u32 pgid = pg->ID;
+	u8 processes = pg->process_count;
+	u16 *process_offset_table = (u16 *)((char *)pg + pg->processes_offset);
+	unsigned int p, chn, mem, mem_id;
+	unsigned int mem_type, max_mem_id, dev_chn;
+
+	if (ipu_ver == IPU_VER_6SE) {
+		mem_type = IPU6SE_FW_PSYS_N_DATA_MEM_TYPE_ID;
+		max_mem_id = IPU6SE_FW_PSYS_N_MEM_ID;
+		dev_chn = IPU6SE_FW_PSYS_N_DEV_CHN_ID;
+	} else if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) {
+		mem_type = IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID;
+		max_mem_id = IPU6_FW_PSYS_N_MEM_ID;
+		dev_chn = IPU6_FW_PSYS_N_DEV_CHN_ID;
+	} else {
+		WARN(1, "%s ipu_ver:[%u] is unsupported!\n", __func__, ipu_ver);
+		return;
+	}
+
+	dev_dbg(&psys->adev->dev, "%s %s pgid %i has %i processes:\n",
+		__func__, note, pgid, processes);
+
+	for (p = 0; p < processes; p++) {
+		struct ipu_fw_psys_process *process =
+		    (struct ipu_fw_psys_process *)
+		    ((char *)pg + process_offset_table[p]);
+		struct ipu6_fw_psys_process_ext *pm_ext =
+		    (struct ipu6_fw_psys_process_ext *)((u8 *)process
+		    + process->process_extension_offset);
+		dev_dbg(&psys->adev->dev, "\t process %i size=%u",
+			p, process->size);
+		if (!process->process_extension_offset)
+			continue;
+
+		for (mem = 0; mem < mem_type; mem++) {
+			mem_id = pm_ext->ext_mem_id[mem];
+			if (mem_id != max_mem_id)
+				dev_dbg(&psys->adev->dev,
+					"\t mem type %u id %d offset=0x%x",
+					mem, mem_id,
+					pm_ext->ext_mem_offset[mem]);
+		}
+		for (chn = 0; chn < dev_chn; chn++) {
+			if (pm_ext->dev_chn_offset[chn] != (u16)(-1))
+				dev_dbg(&psys->adev->dev,
+					"\t dev_chn[%u]=0x%x\n",
+					chn, pm_ext->dev_chn_offset[chn]);
+		}
+	}
+}
+#else
+void ipu6_fw_psys_pg_dump(struct ipu_psys *psys,
+			  struct ipu_psys_kcmd *kcmd, const char *note)
+{
+	if (ipu_ver == IPU_VER_6SE || ipu_ver == IPU_VER_6 ||
+	    ipu_ver == IPU_VER_6EP)
+		return;
+
+	WARN(1, "%s ipu_ver:[%u] is unsupported!\n", __func__, ipu_ver);
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-isys-csi2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-isys-csi2.c
@@ -0,0 +1,513 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <media/ipu-isys.h>
+#include "ipu.h"
+#include "ipu-buttress.h"
+#include "ipu-isys.h"
+#include "ipu-platform-buttress-regs.h"
+#include "ipu-platform-regs.h"
+#include "ipu-platform-isys-csi2-reg.h"
+#include "ipu6-isys-csi2.h"
+#include "ipu6-isys-phy.h"
+#include "ipu-isys-csi2.h"
+
+struct ipu6_csi2_error {
+	const char *error_string;
+	bool is_info_only;
+};
+
+struct ipu6_csi_irq_info_map {
+	u32 irq_error_mask;
+	u32 irq_num;
+	unsigned int irq_base;
+	unsigned int irq_base_ctrl2;
+	struct ipu6_csi2_error *errors;
+};
+
+/*
+ * Strings corresponding to CSI-2 receiver errors are here.
+ * Corresponding macros are defined in the header file.
+ */
+static struct ipu6_csi2_error dphy_rx_errors[] = {
+	{"Single packet header error corrected", true},
+	{"Multiple packet header errors detected", true},
+	{"Payload checksum (CRC) error", true},
+	{"Transfer FIFO overflow", false},
+	{"Reserved short packet data type detected", true},
+	{"Reserved long packet data type detected", true},
+	{"Incomplete long packet detected", false},
+	{"Frame sync error", false},
+	{"Line sync error", false},
+	{"DPHY recoverable synchronization error", true},
+	{"DPHY fatal error", false},
+	{"DPHY elastic FIFO overflow", false},
+	{"Inter-frame short packet discarded", true},
+	{"Inter-frame long packet discarded", true},
+	{"MIPI pktgen overflow", false},
+	{"MIPI pktgen data loss", false},
+	{"FIFO overflow", false},
+	{"Lane deskew", false},
+	{"SOT sync error", false},
+	{"HSIDLE detected", false}
+};
+
+static refcount_t phy_power_ref_count[IPU_ISYS_CSI_PHY_NUM];
+
+static int ipu6_csi2_phy_power_set(struct ipu_isys *isys,
+				   struct ipu_isys_csi2_config *cfg, bool on)
+{
+	int ret = 0;
+	unsigned int port, phy_id;
+	refcount_t *ref;
+	void __iomem *isys_base = isys->pdata->base;
+	unsigned int nr;
+
+	port = cfg->port;
+	phy_id = port / 4;
+	ref = &phy_power_ref_count[phy_id];
+	dev_dbg(&isys->adev->dev, "for phy %d port %d, lanes: %d\n",
+		phy_id, port, cfg->nlanes);
+
+	nr = (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_ISYS_CSI_PORT_NUM : IPU6SE_ISYS_CSI_PORT_NUM;
+
+	if (!isys_base || port >= nr) {
+		dev_warn(&isys->adev->dev, "invalid port ID %d\n", port);
+		return -EINVAL;
+	}
+
+	if (on) {
+		if (refcount_read(ref)) {
+			/* already up */
+			dev_warn(&isys->adev->dev, "for phy %d is already UP",
+				 phy_id);
+			refcount_inc(ref);
+			return 0;
+		}
+
+		ret = ipu6_isys_phy_powerup_ack(isys, phy_id);
+		if (ret)
+			return ret;
+
+		ipu6_isys_phy_reset(isys, phy_id, 0);
+		ipu6_isys_phy_common_init(isys);
+
+		ret = ipu6_isys_phy_config(isys);
+		if (ret)
+			return ret;
+
+		ipu6_isys_phy_reset(isys, phy_id, 1);
+		ret = ipu6_isys_phy_ready(isys, phy_id);
+		if (ret)
+			return ret;
+
+		refcount_set(ref, 1);
+		return 0;
+	}
+
+	/* power off process */
+	if (refcount_dec_and_test(ref))
+		ret = ipu6_isys_phy_powerdown_ack(isys, phy_id);
+	if (ret)
+		dev_err(&isys->adev->dev, "phy poweroff failed!");
+
+	return ret;
+}
+
+static void ipu6_isys_register_errors(struct ipu_isys_csi2 *csi2)
+{
+	u32 mask = 0;
+	u32 irq = readl(csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+			CSI_PORT_REG_BASE_IRQ_STATUS_OFFSET);
+
+	mask = (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_CSI_RX_ERROR_IRQ_MASK : IPU6SE_CSI_RX_ERROR_IRQ_MASK;
+
+	writel(irq & mask,
+	       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+	       CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET);
+	csi2->receiver_errors |= irq & mask;
+}
+
+void ipu_isys_csi2_error(struct ipu_isys_csi2 *csi2)
+{
+	struct ipu6_csi2_error *errors;
+	u32 status;
+	unsigned int i;
+
+	/* Register errors once more in case of error interrupts are disabled */
+	ipu6_isys_register_errors(csi2);
+	status = csi2->receiver_errors;
+	csi2->receiver_errors = 0;
+	errors = dphy_rx_errors;
+
+	for (i = 0; i < CSI_RX_NUM_ERRORS_IN_IRQ; i++) {
+		if (status & BIT(i))
+			dev_err_ratelimited(&csi2->isys->adev->dev,
+					    "csi2-%i error: %s\n",
+					    csi2->index,
+					    errors[i].error_string);
+	}
+}
+
+const unsigned int csi2_port_cfg[][3] = {
+	{0, 0, 0x1f}, /* no link */
+	{4, 0, 0x10}, /* x4 + x4 config */
+	{2, 0, 0x12}, /* x2 + x2 config */
+	{1, 0, 0x13}, /* x1 + x1 config */
+	{2, 1, 0x15}, /* x2x1 + x2x1 config */
+	{1, 1, 0x16}, /* x1x1 + x1x1 config */
+	{2, 2, 0x18}, /* x2x2 + x2x2 config */
+	{1, 2, 0x19}, /* x1x2 + x1x2 config */
+};
+
+const unsigned int phy_port_cfg[][4] = {
+	/* port, nlanes, bbindex, portcfg */
+	/* sip0 */
+	{0, 1, 0, 0x15},
+	{0, 2, 0, 0x15},
+	{0, 4, 0, 0x15},
+	{0, 4, 2, 0x22},
+	/* sip1 */
+	{2, 1, 4, 0x15},
+	{2, 2, 4, 0x15},
+	{2, 4, 4, 0x15},
+	{2, 4, 6, 0x22},
+};
+
+static int ipu_isys_csi2_phy_config_by_port(struct ipu_isys *isys,
+					    unsigned int port,
+					    unsigned int nlanes)
+{
+	void __iomem *base = isys->adev->isp->base;
+	u32 val, reg, i;
+	unsigned int bbnum;
+
+	dev_dbg(&isys->adev->dev, "%s port %u with %u lanes", __func__,
+		port, nlanes);
+
+	/* hard code for x2x2 + x2x2 with <1.5Gbps */
+	for (i = 0; i < IPU6SE_ISYS_PHY_BB_NUM; i++) {
+		/* cphy_dll_ovrd.crcdc_fsm_dlane0 = 13 */
+		reg = IPU6SE_ISYS_PHY_0_BASE + PHY_CPHY_DLL_OVRD(i);
+		val = readl(base + reg);
+		val |= 13 << 1;
+		/* val &= ~0x1; */
+		writel(val, base + reg);
+
+		/* cphy_rx_control1.en_crc1 = 1 */
+		reg = IPU6SE_ISYS_PHY_0_BASE + PHY_CPHY_RX_CONTROL1(i);
+		val = readl(base + reg);
+		val |= 0x1 << 31;
+		writel(val, base + reg);
+
+		/* dphy_cfg.reserved = 1
+		 * dphy_cfg.lden_from_dll_ovrd_0 = 1
+		 */
+		reg = IPU6SE_ISYS_PHY_0_BASE + PHY_DPHY_CFG(i);
+		val = readl(base + reg);
+		val |= 0x1 << 25;
+		val |= 0x1 << 26;
+		writel(val, base + reg);
+
+		/* cphy_dll_ovrd.lden_crcdc_fsm_dlane0 = 1 */
+		reg = IPU6SE_ISYS_PHY_0_BASE + PHY_CPHY_DLL_OVRD(i);
+		val = readl(base + reg);
+		val |= 1;
+		writel(val, base + reg);
+	}
+
+	/* bb afe config, use minimal channel loss */
+	for (i = 0; i < ARRAY_SIZE(phy_port_cfg); i++) {
+		if (phy_port_cfg[i][0] == port &&
+		    phy_port_cfg[i][1] == nlanes) {
+			bbnum = phy_port_cfg[i][2] / 2;
+			reg = IPU6SE_ISYS_PHY_0_BASE + PHY_BB_AFE_CONFIG(bbnum);
+			val = readl(base + reg);
+			val |= phy_port_cfg[i][3];
+			writel(val, base + reg);
+		}
+	}
+
+	return 0;
+}
+
+static void ipu_isys_csi2_rx_control(struct ipu_isys *isys)
+{
+	void __iomem *base = isys->adev->isp->base;
+	u32 val, reg;
+
+	/* lp11 release */
+	reg = CSI2_HUB_GPREG_SIP0_CSI_RX_A_CONTROL;
+	val = readl(base + reg);
+	val |= 0x1;
+	writel(0x1, base + CSI2_HUB_GPREG_SIP0_CSI_RX_A_CONTROL);
+
+	reg = CSI2_HUB_GPREG_SIP0_CSI_RX_B_CONTROL;
+	val = readl(base + reg);
+	val |= 0x1;
+	writel(0x1, base + CSI2_HUB_GPREG_SIP0_CSI_RX_B_CONTROL);
+
+	reg = CSI2_HUB_GPREG_SIP1_CSI_RX_A_CONTROL;
+	val = readl(base + reg);
+	val |= 0x1;
+	writel(0x1, base + CSI2_HUB_GPREG_SIP1_CSI_RX_A_CONTROL);
+
+	reg = CSI2_HUB_GPREG_SIP1_CSI_RX_B_CONTROL;
+	val = readl(base + reg);
+	val |= 0x1;
+	writel(0x1, base + CSI2_HUB_GPREG_SIP1_CSI_RX_B_CONTROL);
+}
+
+static int ipu_isys_csi2_set_port_cfg(struct v4l2_subdev *sd, unsigned int port,
+				      unsigned int nlanes)
+{
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+	struct ipu_isys *isys = csi2->isys;
+	unsigned int sip = port / 2;
+	unsigned int index;
+
+	switch (nlanes) {
+	case 1:
+		index = 5;
+		break;
+	case 2:
+		index = 6;
+		break;
+	case 4:
+		index = 1;
+		break;
+	default:
+		dev_err(&isys->adev->dev, "lanes nr %u is unsupported\n",
+			nlanes);
+		return -EINVAL;
+	}
+
+	dev_dbg(&isys->adev->dev, "port config for port %u with %u lanes\n",
+		port, nlanes);
+	writel(csi2_port_cfg[index][2],
+	       isys->pdata->base + CSI2_HUB_GPREG_SIP_FB_PORT_CFG(sip));
+
+	return 0;
+}
+
+static void ipu_isys_csi2_set_timing(struct v4l2_subdev *sd,
+				     struct ipu_isys_csi2_timing timing,
+				     unsigned int port,
+				     unsigned int nlanes)
+{
+	u32 port_base;
+	void __iomem *reg;
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+	struct ipu_isys *isys = csi2->isys;
+	unsigned int i;
+
+	port_base = (port % 2) ? CSI2_SIP_TOP_CSI_RX_PORT_BASE_1(port) :
+		CSI2_SIP_TOP_CSI_RX_PORT_BASE_0(port);
+
+	dev_dbg(&isys->adev->dev,
+		"set timing for port %u base 0x%x with %u lanes\n",
+		port, port_base, nlanes);
+
+	reg = isys->pdata->base + port_base;
+	reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_TERMEN_CLANE;
+
+	writel(timing.ctermen, reg);
+
+	reg = isys->pdata->base + port_base;
+	reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_SETTLE_CLANE;
+	writel(timing.csettle, reg);
+
+	for (i = 0; i < nlanes; i++) {
+		reg = isys->pdata->base + port_base;
+		reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_TERMEN_DLANE(i);
+		writel(timing.dtermen, reg);
+
+		reg = isys->pdata->base + port_base;
+		reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_SETTLE_DLANE(i);
+		writel(timing.dsettle, reg);
+	}
+}
+
+int ipu_isys_csi2_set_stream(struct v4l2_subdev *sd,
+			     struct ipu_isys_csi2_timing timing,
+			     unsigned int nlanes, int enable)
+{
+	struct ipu_isys_csi2 *csi2 = to_ipu_isys_csi2(sd);
+	struct ipu_isys *isys = csi2->isys;
+	struct ipu_isys_pipeline *ip = container_of(sd->entity.pipe,
+						    struct ipu_isys_pipeline,
+						    pipe);
+	struct ipu_isys_csi2_config *cfg =
+		v4l2_get_subdev_hostdata(media_entity_to_v4l2_subdev
+					 (ip->external->entity));
+	unsigned int port;
+	int ret;
+	u32 mask = 0;
+
+	port = cfg->port;
+	dev_dbg(&isys->adev->dev, "for port %u\n", port);
+
+	mask = (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_CSI_RX_ERROR_IRQ_MASK : IPU6SE_CSI_RX_ERROR_IRQ_MASK;
+
+	if (!enable) {
+
+		writel(0, csi2->base + CSI_REG_CSI_FE_ENABLE);
+		writel(0, csi2->base + CSI_REG_PPI2CSI_ENABLE);
+
+		/* Disable interrupts */
+		writel(0,
+		       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+		       CSI_PORT_REG_BASE_IRQ_ENABLE_OFFSET);
+		writel(mask,
+		       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+		       CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET);
+		writel(0,
+		       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+		       CSI_PORT_REG_BASE_IRQ_ENABLE_OFFSET);
+		writel(0xffffffff,
+		       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+		       CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET);
+
+		/* Disable clock */
+		writel(0, isys->pdata->base +
+		       CSI_REG_HUB_FW_ACCESS_PORT(port));
+		writel(0, isys->pdata->base +
+		       CSI_REG_HUB_DRV_ACCESS_PORT(port));
+
+		if (ipu_ver == IPU_VER_6SE)
+			return 0;
+
+		/* power down */
+		return ipu6_csi2_phy_power_set(isys, cfg, false);
+	}
+
+	if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) {
+		/* Enable DPHY power */
+		ret = ipu6_csi2_phy_power_set(isys, cfg, true);
+		if (ret) {
+			dev_err(&isys->adev->dev,
+				"CSI-%d PHY power up failed %d\n",
+				cfg->port, ret);
+			return ret;
+		}
+	}
+
+	/* reset port reset */
+	writel(0x1, csi2->base + CSI_REG_PORT_GPREG_SRST);
+	usleep_range(100, 200);
+	writel(0x0, csi2->base + CSI_REG_PORT_GPREG_SRST);
+
+	/* Enable port clock */
+	writel(1, isys->pdata->base + CSI_REG_HUB_DRV_ACCESS_PORT(port));
+	writel(1, isys->pdata->base + CSI_REG_HUB_FW_ACCESS_PORT(port));
+
+	if (ipu_ver == IPU_VER_6SE) {
+		ipu_isys_csi2_phy_config_by_port(isys, port, nlanes);
+
+		/* 9'b00010.1000 for 400Mhz isys freqency */
+		writel(0x28,
+		       isys->pdata->base + CSI2_HUB_GPREG_DPHY_TIMER_INCR);
+		/* set port cfg and rx timing */
+		ipu_isys_csi2_set_timing(sd, timing, port, nlanes);
+
+		ret = ipu_isys_csi2_set_port_cfg(sd, port, nlanes);
+		if (ret)
+			return ret;
+
+		ipu_isys_csi2_rx_control(isys);
+	}
+
+	/* enable all error related irq */
+	writel(mask,
+	       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+	       CSI_PORT_REG_BASE_IRQ_STATUS_OFFSET);
+	writel(mask,
+	       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+	       CSI_PORT_REG_BASE_IRQ_MASK_OFFSET);
+	writel(mask,
+	       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+	       CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET);
+	writel(mask,
+	       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+	       CSI_PORT_REG_BASE_IRQ_LEVEL_NOT_PULSE_OFFSET);
+	writel(mask,
+	       csi2->base + CSI_PORT_REG_BASE_IRQ_CSI +
+	       CSI_PORT_REG_BASE_IRQ_ENABLE_OFFSET);
+
+	/* To save CPU wakeups, disable CSI SOF/EOF irq */
+	writel(0xffffffff, csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+	       CSI_PORT_REG_BASE_IRQ_STATUS_OFFSET);
+	writel(0, csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+	       CSI_PORT_REG_BASE_IRQ_MASK_OFFSET);
+	writel(0xffffffff, csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+	       CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET);
+	writel(0, csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+	       CSI_PORT_REG_BASE_IRQ_LEVEL_NOT_PULSE_OFFSET);
+	writel(0xffffffff, csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+	       CSI_PORT_REG_BASE_IRQ_ENABLE_OFFSET);
+
+	/* Configure FE/PPI2CSI and enable FE/ PPI2CSI */
+	writel(0, csi2->base + CSI_REG_CSI_FE_MODE);
+	writel(CSI_SENSOR_INPUT, csi2->base + CSI_REG_CSI_FE_MUX_CTRL);
+	writel(CSI_CNTR_SENSOR_LINE_ID | CSI_CNTR_SENSOR_FRAME_ID,
+	       csi2->base + CSI_REG_CSI_FE_SYNC_CNTR_SEL);
+	writel(((nlanes - 1) <<
+		PPI_INTF_CONFIG_NOF_ENABLED_DATALANES_SHIFT) |
+	       (0 << PPI_INTF_CONFIG_RX_AUTO_CLKGATING_SHIFT),
+	       csi2->base + CSI_REG_PPI2CSI_CONFIG_PPI_INTF);
+	writel(0x06, csi2->base + CSI_REG_PPI2CSI_CONFIG_CSI_FEATURE);
+	writel(1, csi2->base + CSI_REG_PPI2CSI_ENABLE);
+	writel(1, csi2->base + CSI_REG_CSI_FE_ENABLE);
+
+	return 0;
+}
+
+void ipu_isys_csi2_isr(struct ipu_isys_csi2 *csi2)
+{
+	u32 status;
+
+	ipu6_isys_register_errors(csi2);
+
+	status = readl(csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+		       CSI_PORT_REG_BASE_IRQ_STATUS_OFFSET);
+
+	writel(status, csi2->base + CSI_PORT_REG_BASE_IRQ_CSI_SYNC +
+	       CSI_PORT_REG_BASE_IRQ_CLEAR_OFFSET);
+
+	if (status & IPU_CSI_RX_IRQ_FS_VC)
+		ipu_isys_csi2_sof_event(csi2);
+	if (status & IPU_CSI_RX_IRQ_FE_VC)
+		ipu_isys_csi2_eof_event(csi2);
+}
+
+unsigned int ipu_isys_csi2_get_current_field(struct ipu_isys_pipeline *ip,
+					     unsigned int *timestamp)
+{
+	struct ipu_isys_video *av = container_of(ip, struct ipu_isys_video, ip);
+	struct ipu_isys *isys = av->isys;
+	unsigned int field = V4L2_FIELD_TOP;
+
+	struct ipu_isys_buffer *short_packet_ib =
+		list_last_entry(&ip->short_packet_active,
+				struct ipu_isys_buffer, head);
+	struct ipu_isys_private_buffer *pb =
+		ipu_isys_buffer_to_private_buffer(short_packet_ib);
+	struct ipu_isys_mipi_packet_header *ph =
+		(struct ipu_isys_mipi_packet_header *)
+		pb->buffer;
+
+	/* Check if the first SOF packet is received. */
+	if ((ph->dtype & IPU_ISYS_SHORT_PACKET_DTYPE_MASK) != 0)
+		dev_warn(&isys->adev->dev, "First short packet is not SOF.\n");
+	field = (ph->word_count % 2) ? V4L2_FIELD_TOP : V4L2_FIELD_BOTTOM;
+	dev_dbg(&isys->adev->dev,
+		"Interlaced field ready. frame_num = %d field = %d\n",
+		ph->word_count, field);
+
+	return field;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-isys-csi2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-isys-csi2.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Intel Corporation */
+
+#ifndef IPU6_ISYS_CSI2_H
+#define IPU6_ISYS_CSI2_H
+
+struct ipu_isys_csi2_timing;
+struct ipu_isys_csi2;
+struct ipu_isys_pipeline;
+struct v4l2_subdev;
+
+#define IPU_ISYS_SHORT_PACKET_DTYPE_MASK	0x3f
+
+#endif /* IPU6_ISYS_CSI2_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-isys-gpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-isys-gpc.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+#include <linux/pm_runtime.h>
+
+#include "ipu-isys.h"
+#include "ipu-platform-regs.h"
+
+#define IPU_ISYS_GPC_NUM		16
+
+#ifndef CONFIG_PM
+#define pm_runtime_get_sync(d)		0
+#define pm_runtime_put(d)		0
+#endif
+
+struct ipu_isys_gpc {
+	bool enable;
+	unsigned int route;
+	unsigned int source;
+	unsigned int sense;
+	unsigned int gpcindex;
+	void *prit;
+};
+
+struct ipu_isys_gpcs {
+	bool gpc_enable;
+	struct ipu_isys_gpc gpc[IPU_ISYS_GPC_NUM];
+	void *prit;
+};
+
+static int ipu6_isys_gpc_global_enable_get(void *data, u64 *val)
+{
+	struct ipu_isys_gpcs *isys_gpcs = data;
+	struct ipu_isys *isys = isys_gpcs->prit;
+
+	mutex_lock(&isys->mutex);
+
+	*val = isys_gpcs->gpc_enable;
+
+	mutex_unlock(&isys->mutex);
+	return 0;
+}
+
+static int ipu6_isys_gpc_global_enable_set(void *data, u64 val)
+{
+	struct ipu_isys_gpcs *isys_gpcs = data;
+	struct ipu_isys *isys = isys_gpcs->prit;
+	void __iomem *base;
+	int i, ret;
+
+	if (val != 0 && val != 1)
+		return -EINVAL;
+
+	if (!isys || !isys->pdata || !isys->pdata->base)
+		return -EINVAL;
+
+	mutex_lock(&isys->mutex);
+
+	base = isys->pdata->base + IPU_ISYS_GPC_BASE;
+
+	ret = pm_runtime_get_sync(&isys->adev->dev);
+	if (ret < 0) {
+		pm_runtime_put(&isys->adev->dev);
+		mutex_unlock(&isys->mutex);
+		return ret;
+	}
+
+	if (!val) {
+		writel(0x0, base + IPU_ISYS_GPREG_TRACE_TIMER_RST);
+		writel(0x0, base + IPU_ISF_CDC_MMU_GPC_OVERALL_ENABLE);
+		writel(0xffff, base + IPU_ISF_CDC_MMU_GPC_SOFT_RESET);
+		isys_gpcs->gpc_enable = false;
+		for (i = 0; i < IPU_ISYS_GPC_NUM; i++) {
+			isys_gpcs->gpc[i].enable = 0;
+			isys_gpcs->gpc[i].sense = 0;
+			isys_gpcs->gpc[i].route = 0;
+			isys_gpcs->gpc[i].source = 0;
+		}
+		pm_runtime_mark_last_busy(&isys->adev->dev);
+		pm_runtime_put_autosuspend(&isys->adev->dev);
+	} else {
+		/*
+		 * Set gpc reg and start all gpc here.
+		 * RST free running local timer.
+		 */
+		writel(0x0, base + IPU_ISYS_GPREG_TRACE_TIMER_RST);
+		writel(0x1, base + IPU_ISYS_GPREG_TRACE_TIMER_RST);
+
+		for (i = 0; i < IPU_ISYS_GPC_NUM; i++) {
+			/* Enable */
+			writel(isys_gpcs->gpc[i].enable,
+			       base + IPU_ISF_CDC_MMU_GPC_ENABLE0 + 4 * i);
+			/* Setting (route/source/sense) */
+			writel((isys_gpcs->gpc[i].sense
+					<< IPU_GPC_SENSE_OFFSET)
+				+ (isys_gpcs->gpc[i].route
+					<< IPU_GPC_ROUTE_OFFSET)
+				+ (isys_gpcs->gpc[i].source
+					<< IPU_GPC_SOURCE_OFFSET),
+				base + IPU_ISF_CDC_MMU_GPC_CNT_SEL0 + 4 * i);
+		}
+
+		/* Soft reset and Overall Enable. */
+		writel(0x0, base + IPU_ISF_CDC_MMU_GPC_OVERALL_ENABLE);
+		writel(0xffff, base + IPU_ISF_CDC_MMU_GPC_SOFT_RESET);
+		writel(0x1, base + IPU_ISF_CDC_MMU_GPC_OVERALL_ENABLE);
+
+		isys_gpcs->gpc_enable = true;
+	}
+
+	mutex_unlock(&isys->mutex);
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(isys_gpc_globe_enable_fops,
+			ipu6_isys_gpc_global_enable_get,
+			ipu6_isys_gpc_global_enable_set, "%llu\n");
+
+static int ipu6_isys_gpc_count_get(void *data, u64 *val)
+{
+	struct ipu_isys_gpc *isys_gpc = data;
+	struct ipu_isys *isys = isys_gpc->prit;
+	void __iomem *base;
+
+	if (!isys || !isys->pdata || !isys->pdata->base)
+		return -EINVAL;
+
+	spin_lock(&isys->power_lock);
+	if (isys->power) {
+		base = isys->pdata->base + IPU_ISYS_GPC_BASE;
+		*val = readl(base + IPU_ISF_CDC_MMU_GPC_VALUE0
+				 + 4 * isys_gpc->gpcindex);
+	} else {
+		*val = 0;
+	}
+	spin_unlock(&isys->power_lock);
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(isys_gpc_count_fops, ipu6_isys_gpc_count_get,
+			NULL, "%llu\n");
+
+int ipu_isys_gpc_init_debugfs(struct ipu_isys *isys)
+{
+	struct dentry *gpcdir;
+	struct dentry *dir;
+	struct dentry *file;
+	int i;
+	char gpcname[10];
+	struct ipu_isys_gpcs *isys_gpcs;
+
+	isys_gpcs = devm_kzalloc(&isys->adev->dev, sizeof(*isys_gpcs),
+				 GFP_KERNEL);
+	if (!isys_gpcs)
+		return -ENOMEM;
+
+	gpcdir = debugfs_create_dir("gpcs", isys->debugfsdir);
+	if (IS_ERR(gpcdir))
+		return -ENOMEM;
+
+	isys_gpcs->prit = isys;
+	file = debugfs_create_file("enable", 0600, gpcdir, isys_gpcs,
+				   &isys_gpc_globe_enable_fops);
+	if (IS_ERR(file))
+		goto err;
+
+	for (i = 0; i < IPU_ISYS_GPC_NUM; i++) {
+		sprintf(gpcname, "gpc%d", i);
+		dir = debugfs_create_dir(gpcname, gpcdir);
+		if (IS_ERR(dir))
+			goto err;
+
+		debugfs_create_bool("enable", 0600, dir,
+				    &isys_gpcs->gpc[i].enable);
+
+		debugfs_create_u32("source", 0600, dir,
+				   &isys_gpcs->gpc[i].source);
+
+		debugfs_create_u32("route", 0600, dir,
+				   &isys_gpcs->gpc[i].route);
+
+		debugfs_create_u32("sense", 0600, dir,
+				   &isys_gpcs->gpc[i].sense);
+
+		isys_gpcs->gpc[i].gpcindex = i;
+		isys_gpcs->gpc[i].prit = isys;
+		file = debugfs_create_file("count", 0400, dir,
+					   &isys_gpcs->gpc[i],
+					   &isys_gpc_count_fops);
+		if (IS_ERR(file))
+			goto err;
+	}
+
+	return 0;
+
+err:
+	debugfs_remove_recursive(gpcdir);
+	return -ENOMEM;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-isys-phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-isys-phy.c
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2013 - 2020 Intel Corporation
+ */
+
+#include <linux/delay.h>
+#include <media/ipu-isys.h>
+#include <media/v4l2-device.h>
+#include "ipu.h"
+#include "ipu-buttress.h"
+#include "ipu-isys.h"
+#include "ipu-isys-csi2.h"
+#include "ipu-platform-regs.h"
+#include "ipu-platform-isys-csi2-reg.h"
+#include "ipu6-isys-csi2.h"
+#include "ipu6-isys-phy.h"
+
+#define LOOP (2000)
+
+#define PHY_REG_INIT_CTL	     0x00000694
+#define PHY_REG_INIT_CTL_PORT_OFFSET 0x00000600
+
+struct phy_reg {
+	u32 reg;
+	u32 val;
+};
+
+static const struct phy_reg common_init_regs[] = {
+	/* for TGL-U, use 0x80000000 */
+	{0x00000040, 0x80000000},
+	{0x00000044, 0x00a80880},
+	{0x00000044, 0x00b80880},
+	{0x00000010, 0x0000078c},
+	{0x00000344, 0x2f4401e2},
+	{0x00000544, 0x924401e2},
+	{0x00000744, 0x594401e2},
+	{0x00000944, 0x624401e2},
+	{0x00000b44, 0xfc4401e2},
+	{0x00000d44, 0xc54401e2},
+	{0x00000f44, 0x034401e2},
+	{0x00001144, 0x8f4401e2},
+	{0x00001344, 0x754401e2},
+	{0x00001544, 0xe94401e2},
+	{0x00001744, 0xcb4401e2},
+	{0x00001944, 0xfa4401e2}
+};
+
+static const struct phy_reg x1_port0_config_regs[] = {
+	{0x00000694, 0xc80060fa},
+	{0x00000680, 0x3d4f78ea},
+	{0x00000690, 0x10a0140b},
+	{0x000006a8, 0xdf04010a},
+	{0x00000700, 0x57050060},
+	{0x00000710, 0x0030001c},
+	{0x00000738, 0x5f004444},
+	{0x0000073c, 0x78464204},
+	{0x00000748, 0x7821f940},
+	{0x0000074c, 0xb2000433},
+	{0x00000494, 0xfe6030fa},
+	{0x00000480, 0x29ef5ed0},
+	{0x00000490, 0x10a0540b},
+	{0x000004a8, 0x7a01010a},
+	{0x00000500, 0xef053460},
+	{0x00000510, 0xe030101c},
+	{0x00000538, 0xdf808444},
+	{0x0000053c, 0xc8422204},
+	{0x00000540, 0x0180088c},
+	{0x00000574, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x1_port1_config_regs[] = {
+	{0x00000c94, 0xc80060fa},
+	{0x00000c80, 0xcf47abea},
+	{0x00000c90, 0x10a0840b},
+	{0x00000ca8, 0xdf04010a},
+	{0x00000d00, 0x57050060},
+	{0x00000d10, 0x0030001c},
+	{0x00000d38, 0x5f004444},
+	{0x00000d3c, 0x78464204},
+	{0x00000d48, 0x7821f940},
+	{0x00000d4c, 0xb2000433},
+	{0x00000a94, 0xc91030fa},
+	{0x00000a80, 0x5a166ed0},
+	{0x00000a90, 0x10a0540b},
+	{0x00000aa8, 0x5d060100},
+	{0x00000b00, 0xef053460},
+	{0x00000b10, 0xa030101c},
+	{0x00000b38, 0xdf808444},
+	{0x00000b3c, 0xc8422204},
+	{0x00000b40, 0x0180088c},
+	{0x00000b74, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x1_port2_config_regs[] = {
+	{0x00001294, 0x28f000fa},
+	{0x00001280, 0x08130cea},
+	{0x00001290, 0x10a0140b},
+	{0x000012a8, 0xd704010a},
+	{0x00001300, 0x8d050060},
+	{0x00001310, 0x0030001c},
+	{0x00001338, 0xdf008444},
+	{0x0000133c, 0x78422204},
+	{0x00001348, 0x7821f940},
+	{0x0000134c, 0x5a000433},
+	{0x00001094, 0x2d20b0fa},
+	{0x00001080, 0xade75dd0},
+	{0x00001090, 0x10a0540b},
+	{0x000010a8, 0xb101010a},
+	{0x00001100, 0x33053460},
+	{0x00001110, 0x0030101c},
+	{0x00001138, 0xdf808444},
+	{0x0000113c, 0xc8422204},
+	{0x00001140, 0x8180088c},
+	{0x00001174, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x1_port3_config_regs[] = {
+	{0x00001894, 0xc80060fa},
+	{0x00001880, 0x0f90fd6a},
+	{0x00001890, 0x10a0840b},
+	{0x000018a8, 0xdf04010a},
+	{0x00001900, 0x57050060},
+	{0x00001910, 0x0030001c},
+	{0x00001938, 0x5f004444},
+	{0x0000193c, 0x78464204},
+	{0x00001948, 0x7821f940},
+	{0x0000194c, 0xb2000433},
+	{0x00001694, 0x3050d0fa},
+	{0x00001680, 0x0ef6d050},
+	{0x00001690, 0x10a0540b},
+	{0x000016a8, 0xe301010a},
+	{0x00001700, 0x69053460},
+	{0x00001710, 0xa030101c},
+	{0x00001738, 0xdf808444},
+	{0x0000173c, 0xc8422204},
+	{0x00001740, 0x0180088c},
+	{0x00001774, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port0_config_regs[] = {
+	{0x00000694, 0xc80060fa},
+	{0x00000680, 0x3d4f78ea},
+	{0x00000690, 0x10a0140b},
+	{0x000006a8, 0xdf04010a},
+	{0x00000700, 0x57050060},
+	{0x00000710, 0x0030001c},
+	{0x00000738, 0x5f004444},
+	{0x0000073c, 0x78464204},
+	{0x00000748, 0x7821f940},
+	{0x0000074c, 0xb2000433},
+	{0x00000494, 0xc80060fa},
+	{0x00000480, 0x29ef5ed8},
+	{0x00000490, 0x10a0540b},
+	{0x000004a8, 0x7a01010a},
+	{0x00000500, 0xef053460},
+	{0x00000510, 0xe030101c},
+	{0x00000538, 0xdf808444},
+	{0x0000053c, 0xc8422204},
+	{0x00000540, 0x0180088c},
+	{0x00000574, 0x00000000},
+	{0x00000294, 0xc80060fa},
+	{0x00000280, 0xcb45b950},
+	{0x00000290, 0x10a0540b},
+	{0x000002a8, 0x8c01010a},
+	{0x00000300, 0xef053460},
+	{0x00000310, 0x8030101c},
+	{0x00000338, 0x41808444},
+	{0x0000033c, 0x32422204},
+	{0x00000340, 0x0180088c},
+	{0x00000374, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port1_config_regs[] = {
+	{0x00000c94, 0xc80060fa},
+	{0x00000c80, 0xcf47abea},
+	{0x00000c90, 0x10a0840b},
+	{0x00000ca8, 0xdf04010a},
+	{0x00000d00, 0x57050060},
+	{0x00000d10, 0x0030001c},
+	{0x00000d38, 0x5f004444},
+	{0x00000d3c, 0x78464204},
+	{0x00000d48, 0x7821f940},
+	{0x00000d4c, 0xb2000433},
+	{0x00000a94, 0xc80060fa},
+	{0x00000a80, 0x5a166ed8},
+	{0x00000a90, 0x10a0540b},
+	{0x00000aa8, 0x7a01010a},
+	{0x00000b00, 0xef053460},
+	{0x00000b10, 0xa030101c},
+	{0x00000b38, 0xdf808444},
+	{0x00000b3c, 0xc8422204},
+	{0x00000b40, 0x0180088c},
+	{0x00000b74, 0x00000000},
+	{0x00000894, 0xc80060fa},
+	{0x00000880, 0x4d4f21d0},
+	{0x00000890, 0x10a0540b},
+	{0x000008a8, 0x5601010a},
+	{0x00000900, 0xef053460},
+	{0x00000910, 0x8030101c},
+	{0x00000938, 0xdf808444},
+	{0x0000093c, 0xc8422204},
+	{0x00000940, 0x0180088c},
+	{0x00000974, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port2_config_regs[] = {
+	{0x00001294, 0xc80060fa},
+	{0x00001280, 0x08130cea},
+	{0x00001290, 0x10a0140b},
+	{0x000012a8, 0xd704010a},
+	{0x00001300, 0x8d050060},
+	{0x00001310, 0x0030001c},
+	{0x00001338, 0xdf008444},
+	{0x0000133c, 0x78422204},
+	{0x00001348, 0x7821f940},
+	{0x0000134c, 0x5a000433},
+	{0x00001094, 0xc80060fa},
+	{0x00001080, 0xade75dd8},
+	{0x00001090, 0x10a0540b},
+	{0x000010a8, 0xb101010a},
+	{0x00001100, 0x33053460},
+	{0x00001110, 0x0030101c},
+	{0x00001138, 0xdf808444},
+	{0x0000113c, 0xc8422204},
+	{0x00001140, 0x8180088c},
+	{0x00001174, 0x00000000},
+	{0x00000e94, 0xc80060fa},
+	{0x00000e80, 0x0fbf16d0},
+	{0x00000e90, 0x10a0540b},
+	{0x00000ea8, 0x7a01010a},
+	{0x00000f00, 0xf5053460},
+	{0x00000f10, 0xc030101c},
+	{0x00000f38, 0xdf808444},
+	{0x00000f3c, 0xc8422204},
+	{0x00000f40, 0x8180088c},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port3_config_regs[] = {
+	{0x00001894, 0xc80060fa},
+	{0x00001880, 0x0f90fd6a},
+	{0x00001890, 0x10a0840b},
+	{0x000018a8, 0xdf04010a},
+	{0x00001900, 0x57050060},
+	{0x00001910, 0x0030001c},
+	{0x00001938, 0x5f004444},
+	{0x0000193c, 0x78464204},
+	{0x00001948, 0x7821f940},
+	{0x0000194c, 0xb2000433},
+	{0x00001694, 0xc80060fa},
+	{0x00001680, 0x0ef6d058},
+	{0x00001690, 0x10a0540b},
+	{0x000016a8, 0x7a01010a},
+	{0x00001700, 0x69053460},
+	{0x00001710, 0xa030101c},
+	{0x00001738, 0xdf808444},
+	{0x0000173c, 0xc8422204},
+	{0x00001740, 0x0180088c},
+	{0x00001774, 0x00000000},
+	{0x00001494, 0xc80060fa},
+	{0x00001480, 0xf9d34bd0},
+	{0x00001490, 0x10a0540b},
+	{0x000014a8, 0x7a01010a},
+	{0x00001500, 0x1b053460},
+	{0x00001510, 0x0030101c},
+	{0x00001538, 0xdf808444},
+	{0x0000153c, 0xc8422204},
+	{0x00001540, 0x8180088c},
+	{0x00001574, 0x00000000},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port0_config_regs[] = {
+	{0x00000694, 0xc80060fa},
+	{0x00000680, 0x3d4f78fa},
+	{0x00000690, 0x10a0140b},
+	{0x000006a8, 0xdf04010a},
+	{0x00000700, 0x57050060},
+	{0x00000710, 0x0030001c},
+	{0x00000738, 0x5f004444},
+	{0x0000073c, 0x78464204},
+	{0x00000748, 0x7821f940},
+	{0x0000074c, 0xb2000433},
+	{0x00000494, 0xfe6030fa},
+	{0x00000480, 0x29ef5ed8},
+	{0x00000490, 0x10a0540b},
+	{0x000004a8, 0x7a01010a},
+	{0x00000500, 0xef053460},
+	{0x00000510, 0xe030101c},
+	{0x00000538, 0xdf808444},
+	{0x0000053c, 0xc8422204},
+	{0x00000540, 0x0180088c},
+	{0x00000574, 0x00000004},
+	{0x00000294, 0x23e030fa},
+	{0x00000280, 0xcb45b950},
+	{0x00000290, 0x10a0540b},
+	{0x000002a8, 0x8c01010a},
+	{0x00000300, 0xef053460},
+	{0x00000310, 0x8030101c},
+	{0x00000338, 0x41808444},
+	{0x0000033c, 0x32422204},
+	{0x00000340, 0x0180088c},
+	{0x00000374, 0x00000004},
+	{0x00000894, 0x5620b0fa},
+	{0x00000880, 0x4d4f21dc},
+	{0x00000890, 0x10a0540b},
+	{0x000008a8, 0x5601010a},
+	{0x00000900, 0xef053460},
+	{0x00000910, 0x8030101c},
+	{0x00000938, 0xdf808444},
+	{0x0000093c, 0xc8422204},
+	{0x00000940, 0x0180088c},
+	{0x00000974, 0x00000004},
+	{0x00000a94, 0xc91030fa},
+	{0x00000a80, 0x5a166ecc},
+	{0x00000a90, 0x10a0540b},
+	{0x00000aa8, 0x5d01010a},
+	{0x00000b00, 0xef053460},
+	{0x00000b10, 0xa030101c},
+	{0x00000b38, 0xdf808444},
+	{0x00000b3c, 0xc8422204},
+	{0x00000b40, 0x0180088c},
+	{0x00000b74, 0x00000004},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port1_config_regs[] = {
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port2_config_regs[] = {
+	{0x00001294, 0x28f000fa},
+	{0x00001280, 0x08130cfa},
+	{0x00001290, 0x10c0140b},
+	{0x000012a8, 0xd704010a},
+	{0x00001300, 0x8d050060},
+	{0x00001310, 0x0030001c},
+	{0x00001338, 0xdf008444},
+	{0x0000133c, 0x78422204},
+	{0x00001348, 0x7821f940},
+	{0x0000134c, 0x5a000433},
+	{0x00001094, 0x2d20b0fa},
+	{0x00001080, 0xade75dd8},
+	{0x00001090, 0x10a0540b},
+	{0x000010a8, 0xb101010a},
+	{0x00001100, 0x33053460},
+	{0x00001110, 0x0030101c},
+	{0x00001138, 0xdf808444},
+	{0x0000113c, 0xc8422204},
+	{0x00001140, 0x8180088c},
+	{0x00001174, 0x00000004},
+	{0x00000e94, 0xd308d0fa},
+	{0x00000e80, 0x0fbf16d0},
+	{0x00000e90, 0x10a0540b},
+	{0x00000ea8, 0x2c01010a},
+	{0x00000f00, 0xf5053460},
+	{0x00000f10, 0xc030101c},
+	{0x00000f38, 0xdf808444},
+	{0x00000f3c, 0xc8422204},
+	{0x00000f40, 0x8180088c},
+	{0x00000f74, 0x00000004},
+	{0x00001494, 0x136850fa},
+	{0x00001480, 0xf9d34bdc},
+	{0x00001490, 0x10a0540b},
+	{0x000014a8, 0x5a01010a},
+	{0x00001500, 0x1b053460},
+	{0x00001510, 0x0030101c},
+	{0x00001538, 0xdf808444},
+	{0x0000153c, 0xc8422204},
+	{0x00001540, 0x8180088c},
+	{0x00001574, 0x00000004},
+	{0x00001694, 0x3050d0fa},
+	{0x00001680, 0x0ef6d04c},
+	{0x00001690, 0x10a0540b},
+	{0x000016a8, 0xe301010a},
+	{0x00001700, 0x69053460},
+	{0x00001710, 0xa030101c},
+	{0x00001738, 0xdf808444},
+	{0x0000173c, 0xc8422204},
+	{0x00001740, 0x0180088c},
+	{0x00001774, 0x00000004},
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port3_config_regs[] = {
+	{0x00000000, 0x00000000}
+};
+
+static const struct phy_reg *x1_config_regs[4] = {
+	x1_port0_config_regs,
+	x1_port1_config_regs,
+	x1_port2_config_regs,
+	x1_port3_config_regs
+};
+
+static const struct phy_reg *x2_config_regs[4] = {
+	x2_port0_config_regs,
+	x2_port1_config_regs,
+	x2_port2_config_regs,
+	x2_port3_config_regs
+};
+
+static const struct phy_reg *x4_config_regs[4] = {
+	x4_port0_config_regs,
+	x4_port1_config_regs,
+	x4_port2_config_regs,
+	x4_port3_config_regs
+};
+
+static const struct phy_reg **config_regs[3] = {
+	x1_config_regs,
+	x2_config_regs,
+	x4_config_regs,
+};
+
+int ipu6_isys_phy_powerup_ack(struct ipu_isys *isys, unsigned int phy_id)
+{
+	unsigned int i;
+	u32 val;
+	void __iomem *isys_base = isys->pdata->base;
+
+	val = readl(isys_base + CSI_REG_HUB_GPREG_PHY_CONTROL(phy_id));
+	val |= CSI_REG_HUB_GPREG_PHY_CONTROL_PWR_EN;
+	writel(val, isys_base + CSI_REG_HUB_GPREG_PHY_CONTROL(phy_id));
+
+	for (i = 0; i < LOOP; i++) {
+		if (readl(isys_base + CSI_REG_HUB_GPREG_PHY_STATUS(phy_id)) &
+		    CSI_REG_HUB_GPREG_PHY_STATUS_POWER_ACK)
+			return 0;
+		usleep_range(100, 200);
+	}
+
+	dev_warn(&isys->adev->dev, "PHY%d powerup ack timeout", phy_id);
+
+	return -ETIMEDOUT;
+}
+
+int ipu6_isys_phy_powerdown_ack(struct ipu_isys *isys, unsigned int phy_id)
+{
+	unsigned int i;
+	u32 val;
+	void __iomem *isys_base = isys->pdata->base;
+
+	writel(0, isys_base + CSI_REG_HUB_GPREG_PHY_CONTROL(phy_id));
+	for (i = 0; i < LOOP; i++) {
+		usleep_range(10, 20);
+		val = readl(isys_base + CSI_REG_HUB_GPREG_PHY_STATUS(phy_id));
+		if (!(val & CSI_REG_HUB_GPREG_PHY_STATUS_POWER_ACK))
+			return 0;
+	}
+
+	dev_warn(&isys->adev->dev, "PHY %d poweroff ack timeout.\n", phy_id);
+
+	return -ETIMEDOUT;
+}
+
+int ipu6_isys_phy_reset(struct ipu_isys *isys, unsigned int phy_id,
+			bool assert)
+{
+	void __iomem *isys_base = isys->pdata->base;
+	u32 val;
+
+	val = readl(isys_base + CSI_REG_HUB_GPREG_PHY_CONTROL(phy_id));
+	if (assert)
+		val |= CSI_REG_HUB_GPREG_PHY_CONTROL_RESET;
+	else
+		val &= ~(CSI_REG_HUB_GPREG_PHY_CONTROL_RESET);
+
+	writel(val, isys_base + CSI_REG_HUB_GPREG_PHY_CONTROL(phy_id));
+
+	return 0;
+}
+
+int ipu6_isys_phy_ready(struct ipu_isys *isys, unsigned int phy_id)
+{
+	unsigned int i;
+	u32 val;
+	void __iomem *isys_base = isys->pdata->base;
+
+	for (i = 0; i < LOOP; i++) {
+		val = readl(isys_base + CSI_REG_HUB_GPREG_PHY_STATUS(phy_id));
+		dev_dbg(&isys->adev->dev, "PHY%d ready status 0x%x\n",
+			phy_id, val);
+		if (val & CSI_REG_HUB_GPREG_PHY_STATUS_PHY_READY)
+			return 0;
+		usleep_range(10, 20);
+	}
+
+	dev_warn(&isys->adev->dev, "PHY%d ready timeout\n", phy_id);
+
+	return -ETIMEDOUT;
+}
+
+int ipu6_isys_phy_common_init(struct ipu_isys *isys)
+{
+	unsigned int phy_id;
+	void __iomem *phy_base;
+	struct ipu_bus_device *adev = to_ipu_bus_device(&isys->adev->dev);
+	struct ipu_device *isp = adev->isp;
+	void __iomem *isp_base = isp->base;
+	struct v4l2_async_subdev *asd;
+	struct sensor_async_subdev *s_asd;
+	unsigned int i;
+
+	list_for_each_entry(asd, &isys->notifier.asd_list, asd_list) {
+		s_asd = container_of(asd, struct sensor_async_subdev, asd);
+		phy_id = s_asd->csi2.port / 4;
+		phy_base = isp_base + IPU6_ISYS_PHY_BASE(phy_id);
+
+		for (i = 0 ; i < ARRAY_SIZE(common_init_regs); i++) {
+			writel(common_init_regs[i].val,
+				phy_base + common_init_regs[i].reg);
+		}
+	}
+
+	return 0;
+}
+
+static int ipu6_isys_driver_port_to_phy_port(struct ipu_isys_csi2_config *cfg)
+{
+	int phy_port;
+	int ret;
+
+	if (!(cfg->nlanes == 4 || cfg->nlanes == 2 || cfg->nlanes == 1))
+		return -EINVAL;
+
+	/* B,F -> C0 A,E -> C1 C,G -> C2 D,H -> C4 */
+	/* normalize driver port number */
+	phy_port = cfg->port % 4;
+
+	/* swap port number only for A and B */
+	if (phy_port == 0)
+		phy_port = 1;
+	else if (phy_port == 1)
+		phy_port = 0;
+
+	ret = phy_port;
+
+	/* check validity per lane configuration */
+	if ((cfg->nlanes == 4) &&
+		 !(phy_port == 0 || phy_port == 2))
+		ret = -EINVAL;
+	else if ((cfg->nlanes == 2 || cfg->nlanes == 1) &&
+		 !(phy_port >= 0 && phy_port <= 3))
+		ret = -EINVAL;
+
+	return ret;
+}
+
+int ipu6_isys_phy_config(struct ipu_isys *isys)
+{
+	int phy_port;
+	unsigned int phy_id;
+	void __iomem *phy_base;
+	struct ipu_bus_device *adev = to_ipu_bus_device(&isys->adev->dev);
+	struct ipu_device *isp = adev->isp;
+	void __iomem *isp_base = isp->base;
+	const struct phy_reg **phy_config_regs;
+	struct v4l2_async_subdev *asd;
+	struct sensor_async_subdev *s_asd;
+	struct ipu_isys_csi2_config cfg;
+	int i;
+
+	list_for_each_entry(asd, &isys->notifier.asd_list, asd_list) {
+		s_asd = container_of(asd, struct sensor_async_subdev, asd);
+		cfg.port = s_asd->csi2.port;
+		cfg.nlanes = s_asd->csi2.nlanes;
+		phy_port = ipu6_isys_driver_port_to_phy_port(&cfg);
+		if (phy_port < 0) {
+			dev_err(&isys->adev->dev, "invalid port %d for lane %d",
+				cfg.port, cfg.nlanes);
+			return -ENXIO;
+		}
+
+		phy_id = cfg.port / 4;
+		phy_base = isp_base + IPU6_ISYS_PHY_BASE(phy_id);
+		dev_dbg(&isys->adev->dev, "port%d PHY%u lanes %u\n",
+			cfg.port, phy_id, cfg.nlanes);
+
+		phy_config_regs = config_regs[cfg.nlanes/2];
+		cfg.port = phy_port;
+		for (i = 0; phy_config_regs[cfg.port][i].reg; i++) {
+			writel(phy_config_regs[cfg.port][i].val,
+				phy_base + phy_config_regs[cfg.port][i].reg);
+		}
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-isys-phy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-isys-phy.h
@@ -0,0 +1,159 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013 - 2020 Intel Corporation
+ */
+
+#ifndef IPU6_ISYS_PHY_H
+#define IPU6_ISYS_PHY_H
+
+/* bridge to phy in buttress reg map, each phy has 16 kbytes
+ * for tgl u/y, only 2 phys
+ */
+#define IPU6_ISYS_PHY_0_BASE			0x10000
+#define IPU6_ISYS_PHY_1_BASE			0x14000
+#define IPU6_ISYS_PHY_2_BASE			0x18000
+#define IPU6_ISYS_PHY_BASE(i)			(0x10000 + (i) * 0x4000)
+
+/* ppi mapping per phy :
+ *
+ * x4x4:
+ * port0 - PPI range {0, 1, 2, 3, 4}
+ * port2 - PPI range {6, 7, 8, 9, 10}
+ *
+ * x4x2:
+ * port0 - PPI range {0, 1, 2, 3, 4}
+ * port2 - PPI range {6, 7, 8}
+ *
+ * x2x4:
+ * port0 - PPI range {0, 1, 2}
+ * port2 - PPI range {6, 7, 8, 9, 10}
+ *
+ * x2x2:
+ * port0 - PPI range {0, 1, 2}
+ * port1 - PPI range {3, 4, 5}
+ * port2 - PPI range {6, 7, 8}
+ * port3 - PPI range {9, 10, 11}
+ */
+
+/* cbbs config regs */
+#define PHY_CBBS1_BASE				0x0
+/* register offset */
+#define PHY_CBBS1_DFX_VMISCCTL			0x0
+#define PHY_CBBS1_DFX_VBYTESEL0			0x4
+#define PHY_CBBS1_DFX_VBYTESEL1			0x8
+#define PHY_CBBS1_VISA2OBS_CTRL_REG		0xc
+#define PHY_CBBS1_PGL_CTRL_REG			0x10
+#define PHY_CBBS1_RCOMP_CTRL_REG_1		0x14
+#define PHY_CBBS1_RCOMP_CTRL_REG_2		0x18
+#define PHY_CBBS1_RCOMP_CTRL_REG_3		0x1c
+#define PHY_CBBS1_RCOMP_CTRL_REG_4		0x20
+#define PHY_CBBS1_RCOMP_CTRL_REG_5		0x24
+#define PHY_CBBS1_RCOMP_STATUS_REG_1		0x28
+#define PHY_CBBS1_RCOMP_STATUS_REG_2		0x2c
+#define PHY_CBBS1_CLOCK_CTRL_REG		0x30
+#define PHY_CBBS1_CBB_ISOLATION_REG		0x34
+#define PHY_CBBS1_CBB_PLL_CONTROL		0x38
+#define PHY_CBBS1_CBB_STATUS_REG		0x3c
+#define PHY_CBBS1_AFE_CONTROL_REG_1		0x40
+#define PHY_CBBS1_AFE_CONTROL_REG_2		0x44
+#define PHY_CBBS1_CBB_SPARE			0x48
+#define PHY_CBBS1_CRI_CLK_CONTROL		0x4c
+
+/* dbbs shared, i = [0..11] */
+#define PHY_DBBS_SHARED(ppi)			((ppi) * 0x200 + 0x200)
+/* register offset */
+#define PHY_DBBDFE_DFX_V1MISCCTL		0x0
+#define PHY_DBBDFE_DFX_V1BYTESEL0		0x4
+#define PHY_DBBDFE_DFX_V1BYTESEL1		0x8
+#define PHY_DBBDFE_DFX_V2MISCCTL		0xc
+#define PHY_DBBDFE_DFX_V2BYTESEL0		0x10
+#define PHY_DBBDFE_DFX_V2BYTESEL1		0x14
+#define PHY_DBBDFE_GBLCTL			0x18
+#define PHY_DBBDFE_GBL_STATUS			0x1c
+
+/* dbbs udln, i = [0..11] */
+#define IPU6_ISYS_PHY_DBBS_UDLN(ppi)		((ppi) * 0x200 + 0x280)
+/* register offset */
+#define PHY_DBBUDLN_CTL				0x0
+#define PHY_DBBUDLN_CLK_CTL			0x4
+#define PHY_DBBUDLN_SOFT_RST_CTL		0x8
+#define PHY_DBBUDLN_STRAP_VALUES		0xc
+#define PHY_DBBUDLN_TXRX_CTL			0x10
+#define PHY_DBBUDLN_MST_SLV_INIT_CTL		0x14
+#define PHY_DBBUDLN_TX_TIMING_CTL0		0x18
+#define PHY_DBBUDLN_TX_TIMING_CTL1		0x1c
+#define PHY_DBBUDLN_TX_TIMING_CTL2		0x20
+#define PHY_DBBUDLN_TX_TIMING_CTL3		0x24
+#define PHY_DBBUDLN_RX_TIMING_CTL		0x28
+#define PHY_DBBUDLN_PPI_STATUS_CTL		0x2c
+#define PHY_DBBUDLN_PPI_STATUS			0x30
+#define PHY_DBBUDLN_ERR_CTL			0x34
+#define PHY_DBBUDLN_ERR_STATUS			0x38
+#define PHY_DBBUDLN_DFX_LPBK_CTL		0x3c
+#define PHY_DBBUDLN_DFX_PPI_CTL			0x40
+#define PHY_DBBUDLN_DFX_TX_DPHY_CTL		0x44
+#define PHY_DBBUDLN_DFX_TXRX_PRBSPAT_CTL	0x48
+#define PHY_DBBUDLN_DFX_TXRX_PRBSPAT_SEED	0x4c
+#define PHY_DBBUDLN_DFX_PRBSPAT_MAX_WRD_CNT	0x50
+#define PHY_DBBUDLN_DFX_PRBSPAT_STATUS		0x54
+#define PHY_DBBUDLN_DFX_PRBSPAT_WRD_CNT0_STATUS	0x58
+#define PHY_DBBUDLN_DFX_PRBSPAT_WRD_CNT1_STATUS	0x5c
+#define PHY_DBBUDLN_DFX_PRBSPAT_FF_ERR_STATUS	0x60
+#define PHY_DBBUDLN_DFX_PRBSPAT_FF_REF_STATUS		0x64
+#define PHY_DBBUDLN_DFX_PRBSPAT_FF_WRD_CNT0_STATUS	0x68
+#define PHY_DBBUDLN_DFX_PRBSPAT_FF_WRD_CNT1_STATUS	0x6c
+#define PHY_DBBUDLN_RSVD_CTL				0x70
+#define PHY_DBBUDLN_TINIT_DONE				BIT(27)
+
+/* dbbs supar, i = [0..11] */
+#define IPU6_ISYS_PHY_DBBS_SUPAR(ppi)		((ppi) * 0x200 + 0x300)
+/* register offset */
+#define PHY_DBBSUPAR_TXRX_FUPAR_CTL		0x0
+#define PHY_DBBSUPAR_TXHS_AFE_CTL		0x4
+#define PHY_DBBSUPAR_TXHS_AFE_LEGDIS_CTL	0x8
+#define PHY_DBBSUPAR_TXHS_AFE_EQ_CTL		0xc
+#define PHY_DBBSUPAR_RXHS_AFE_CTL1		0x10
+#define PHY_DBBSUPAR_RXHS_AFE_PICTL1		0x14
+#define PHY_DBBSUPAR_TXRXLP_AFE_CTL		0x18
+#define PHY_DBBSUPAR_DFX_TXRX_STATUS		0x1c
+#define PHY_DBBSUPAR_DFX_TXRX_CTL		0x20
+#define PHY_DBBSUPAR_DFX_DIGMON_CTL		0x24
+#define PHY_DBBSUPAR_DFX_LOCMON_CTL		0x28
+#define PHY_DBBSUPAR_DFX_RCOMP_CTL1		0x2c
+#define PHY_DBBSUPAR_DFX_RCOMP_CTL2		0x30
+#define PHY_DBBSUPAR_CAL_TOP1			0x34
+#define PHY_DBBSUPAR_CAL_SHARED1		0x38
+#define PHY_DBBSUPAR_CAL_SHARED2		0x3c
+#define PHY_DBBSUPAR_CAL_CDR1			0x40
+#define PHY_DBBSUPAR_CAL_OCAL1			0x44
+#define PHY_DBBSUPAR_CAL_DCC_DLL1		0x48
+#define PHY_DBBSUPAR_CAL_DLL2			0x4c
+#define PHY_DBBSUPAR_CAL_DFX1			0x50
+#define PHY_DBBSUPAR_CAL_DFX2			0x54
+#define PHY_DBBSUPAR_CAL_DFX3			0x58
+#define PHY_BBSUPAR_CAL_DFX4			0x5c
+#define PHY_DBBSUPAR_CAL_DFX5			0x60
+#define PHY_DBBSUPAR_CAL_DFX6			0x64
+#define PHY_DBBSUPAR_CAL_DFX7			0x68
+#define PHY_DBBSUPAR_DFX_AFE_SPARE_CTL1		0x6c
+#define PHY_DBBSUPAR_DFX_AFE_SPARE_CTL2		0x70
+#define	PHY_DBBSUPAR_SPARE			0x74
+
+/* sai, i = [0..11] */
+#define	IPU6_ISYS_PHY_SAI			0xf800
+/* register offset */
+#define PHY_SAI_CTRL_REG0                       0x40
+#define PHY_SAI_CTRL_REG0_1                     0x44
+#define PHY_SAI_WR_REG0                         0x48
+#define PHY_SAI_WR_REG0_1                       0x4c
+#define PHY_SAI_RD_REG0                         0x50
+#define PHY_SAI_RD_REG0_1                       0x54
+
+int ipu6_isys_phy_powerup_ack(struct ipu_isys *isys, unsigned int phy_id);
+int ipu6_isys_phy_powerdown_ack(struct ipu_isys *isys, unsigned int phy_id);
+int ipu6_isys_phy_reset(struct ipu_isys *isys, unsigned int phy_id,
+			bool assert);
+int ipu6_isys_phy_ready(struct ipu_isys *isys, unsigned int phy_id);
+int ipu6_isys_phy_common_init(struct ipu_isys *isys);
+int ipu6_isys_phy_config(struct ipu_isys *isys);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-isys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-isys.c
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#include <linux/module.h>
+#include <media/v4l2-event.h>
+
+#include "ipu.h"
+#include "ipu-platform-regs.h"
+#include "ipu-trace.h"
+#include "ipu-isys.h"
+#include "ipu-platform-isys-csi2-reg.h"
+
+const struct ipu_isys_pixelformat ipu_isys_pfmts[] = {
+	{V4L2_PIX_FMT_SBGGR12, 16, 12, 0, MEDIA_BUS_FMT_SBGGR12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGBRG12, 16, 12, 0, MEDIA_BUS_FMT_SGBRG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGRBG12, 16, 12, 0, MEDIA_BUS_FMT_SGRBG12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SRGGB12, 16, 12, 0, MEDIA_BUS_FMT_SRGGB12_1X12,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SBGGR10, 16, 10, 0, MEDIA_BUS_FMT_SBGGR10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGBRG10, 16, 10, 0, MEDIA_BUS_FMT_SGBRG10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SGRBG10, 16, 10, 0, MEDIA_BUS_FMT_SGRBG10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SRGGB10, 16, 10, 0, MEDIA_BUS_FMT_SRGGB10_1X10,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW16},
+	{V4L2_PIX_FMT_SBGGR8, 8, 8, 0, MEDIA_BUS_FMT_SBGGR8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SGBRG8, 8, 8, 0, MEDIA_BUS_FMT_SGBRG8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SGRBG8, 8, 8, 0, MEDIA_BUS_FMT_SGRBG8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{V4L2_PIX_FMT_SRGGB8, 8, 8, 0, MEDIA_BUS_FMT_SRGGB8_1X8,
+	 IPU_FW_ISYS_FRAME_FORMAT_RAW8},
+	{}
+};
+
+struct ipu_trace_block isys_trace_blocks[] = {
+	{
+		.offset = IPU_TRACE_REG_IS_TRACE_UNIT_BASE,
+		.type = IPU_TRACE_BLOCK_TUN,
+	},
+	{
+		.offset = IPU_TRACE_REG_IS_SP_EVQ_BASE,
+		.type = IPU_TRACE_BLOCK_TM,
+	},
+	{
+		.offset = IPU_TRACE_REG_IS_SP_GPC_BASE,
+		.type = IPU_TRACE_BLOCK_GPC,
+	},
+	{
+		.offset = IPU_TRACE_REG_IS_ISL_GPC_BASE,
+		.type = IPU_TRACE_BLOCK_GPC,
+	},
+	{
+		.offset = IPU_TRACE_REG_IS_MMU_GPC_BASE,
+		.type = IPU_TRACE_BLOCK_GPC,
+	},
+	{
+		/* Note! this covers all 8 blocks */
+		.offset = IPU_TRACE_REG_CSI2_TM_BASE(0),
+		.type = IPU_TRACE_CSI2,
+	},
+	{
+		/* Note! this covers all 11 blocks */
+		.offset = IPU_TRACE_REG_CSI2_PORT_SIG2SIO_GR_BASE(0),
+		.type = IPU_TRACE_SIG2CIOS,
+	},
+	{
+		.offset = IPU_TRACE_REG_IS_GPREG_TRACE_TIMER_RST_N,
+		.type = IPU_TRACE_TIMER_RST,
+	},
+	{
+		.type = IPU_TRACE_BLOCK_END,
+	}
+};
+
+void isys_setup_hw(struct ipu_isys *isys)
+{
+	void __iomem *base = isys->pdata->base;
+	const u8 *thd = isys->pdata->ipdata->hw_variant.cdc_fifo_threshold;
+	u32 irqs = 0;
+	unsigned int i, nr;
+
+	nr = (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) ?
+		IPU6_ISYS_CSI_PORT_NUM : IPU6SE_ISYS_CSI_PORT_NUM;
+
+	/* Enable irqs for all MIPI ports */
+	for (i = 0; i < nr; i++)
+		irqs |= IPU_ISYS_UNISPART_IRQ_CSI2(i);
+
+	writel(irqs, base + IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_EDGE);
+	writel(irqs, base + IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_LEVEL_NOT_PULSE);
+	writel(0xffffffff, base + IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_CLEAR);
+	writel(irqs, base + IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_MASK);
+	writel(irqs, base + IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_ENABLE);
+
+	irqs = ISYS_UNISPART_IRQS;
+	writel(irqs, base + IPU_REG_ISYS_UNISPART_IRQ_EDGE);
+	writel(irqs, base + IPU_REG_ISYS_UNISPART_IRQ_LEVEL_NOT_PULSE);
+	writel(0xffffffff, base + IPU_REG_ISYS_UNISPART_IRQ_CLEAR);
+	writel(irqs, base + IPU_REG_ISYS_UNISPART_IRQ_MASK);
+	writel(irqs, base + IPU_REG_ISYS_UNISPART_IRQ_ENABLE);
+
+	writel(0, base + IPU_REG_ISYS_UNISPART_SW_IRQ_REG);
+	writel(0, base + IPU_REG_ISYS_UNISPART_SW_IRQ_MUX_REG);
+
+	/* Write CDC FIFO threshold values for isys */
+	for (i = 0; i < isys->pdata->ipdata->hw_variant.cdc_fifos; i++)
+		writel(thd[i], base + IPU_REG_ISYS_CDC_THRESHOLD(i));
+}
+
+irqreturn_t isys_isr(struct ipu_bus_device *adev)
+{
+	struct ipu_isys *isys = ipu_bus_get_drvdata(adev);
+	void __iomem *base = isys->pdata->base;
+	u32 status_sw, status_csi;
+
+	spin_lock(&isys->power_lock);
+	if (!isys->power) {
+		spin_unlock(&isys->power_lock);
+		return IRQ_NONE;
+	}
+
+	status_csi = readl(isys->pdata->base +
+			   IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_STATUS);
+	status_sw = readl(isys->pdata->base + IPU_REG_ISYS_UNISPART_IRQ_STATUS);
+
+	writel(ISYS_UNISPART_IRQS & ~IPU_ISYS_UNISPART_IRQ_SW,
+	       base + IPU_REG_ISYS_UNISPART_IRQ_MASK);
+
+	do {
+		writel(status_csi, isys->pdata->base +
+			   IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_CLEAR);
+		writel(status_sw, isys->pdata->base +
+			   IPU_REG_ISYS_UNISPART_IRQ_CLEAR);
+
+		if (isys->isr_csi2_bits & status_csi) {
+			unsigned int i;
+
+			for (i = 0; i < isys->pdata->ipdata->csi2.nports; i++) {
+				/* irq from not enabled port */
+				if (!isys->csi2[i].base)
+					continue;
+				if (status_csi & IPU_ISYS_UNISPART_IRQ_CSI2(i))
+					ipu_isys_csi2_isr(&isys->csi2[i]);
+			}
+		}
+
+		writel(0, base + IPU_REG_ISYS_UNISPART_SW_IRQ_REG);
+
+		if (!isys_isr_one(adev))
+			status_sw = IPU_ISYS_UNISPART_IRQ_SW;
+		else
+			status_sw = 0;
+
+		status_csi = readl(isys->pdata->base +
+				       IPU_REG_ISYS_CSI_TOP_CTRL0_IRQ_STATUS);
+		status_sw |= readl(isys->pdata->base +
+				       IPU_REG_ISYS_UNISPART_IRQ_STATUS);
+	} while (((status_csi & isys->isr_csi2_bits) ||
+		  (status_sw & IPU_ISYS_UNISPART_IRQ_SW)) &&
+		 !isys->adev->isp->flr_done);
+
+	writel(ISYS_UNISPART_IRQS, base + IPU_REG_ISYS_UNISPART_IRQ_MASK);
+
+	spin_unlock(&isys->power_lock);
+
+	return IRQ_HANDLED;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-l-scheduler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-l-scheduler.c
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#include "ipu-psys.h"
+#include "ipu6-ppg.h"
+
+extern bool enable_power_gating;
+
+struct sched_list {
+	struct list_head list;
+	/* to protect the list */
+	struct mutex lock;
+};
+
+static struct sched_list start_list = {
+	.list	= LIST_HEAD_INIT(start_list.list),
+	.lock	= __MUTEX_INITIALIZER(start_list.lock),
+};
+
+static struct sched_list stop_list = {
+	.list	= LIST_HEAD_INIT(stop_list.list),
+	.lock	= __MUTEX_INITIALIZER(stop_list.lock),
+};
+
+static struct sched_list *get_sc_list(enum SCHED_LIST type)
+{
+	/* for debug purposes */
+	WARN_ON(type != SCHED_START_LIST && type != SCHED_STOP_LIST);
+
+	if (type == SCHED_START_LIST)
+		return &start_list;
+	return &stop_list;
+}
+
+static bool is_kppg_in_list(struct ipu_psys_ppg *kppg, struct list_head *head)
+{
+	struct ipu_psys_ppg *tmp;
+
+	list_for_each_entry(tmp, head, sched_list) {
+		if (kppg == tmp)
+			return true;
+	}
+
+	return false;
+}
+
+void ipu_psys_scheduler_remove_kppg(struct ipu_psys_ppg *kppg,
+				    enum SCHED_LIST type)
+{
+	struct sched_list *sc_list = get_sc_list(type);
+	struct ipu_psys_ppg *tmp0, *tmp1;
+	struct ipu_psys *psys = kppg->fh->psys;
+
+	mutex_lock(&sc_list->lock);
+	list_for_each_entry_safe(tmp0, tmp1, &sc_list->list, sched_list) {
+		if (tmp0 == kppg) {
+			dev_dbg(&psys->adev->dev,
+				 "remove from %s list, kppg(%d 0x%p) state %d\n",
+				 type == SCHED_START_LIST ? "start" : "stop",
+				 kppg->kpg->pg->ID, kppg, kppg->state);
+			list_del_init(&kppg->sched_list);
+		}
+	}
+	mutex_unlock(&sc_list->lock);
+}
+
+void ipu_psys_scheduler_add_kppg(struct ipu_psys_ppg *kppg,
+				 enum SCHED_LIST type)
+{
+	int cur_pri = kppg->pri_base + kppg->pri_dynamic;
+	struct sched_list *sc_list = get_sc_list(type);
+	struct ipu_psys *psys = kppg->fh->psys;
+	struct ipu_psys_ppg *tmp0, *tmp1;
+
+	dev_dbg(&psys->adev->dev,
+		"add to %s list, kppg(%d 0x%p) state %d prio(%d %d) fh 0x%p\n",
+		type == SCHED_START_LIST ? "start" : "stop",
+		kppg->kpg->pg->ID, kppg, kppg->state,
+		kppg->pri_base, kppg->pri_dynamic, kppg->fh);
+
+	mutex_lock(&sc_list->lock);
+	if (list_empty(&sc_list->list)) {
+		list_add(&kppg->sched_list, &sc_list->list);
+		goto out;
+	}
+
+	if (is_kppg_in_list(kppg, &sc_list->list)) {
+		dev_dbg(&psys->adev->dev, "kppg already in list\n");
+		goto out;
+	}
+
+	list_for_each_entry_safe(tmp0, tmp1, &sc_list->list, sched_list) {
+		int tmp_pri = tmp0->pri_base + tmp0->pri_dynamic;
+
+		dev_dbg(&psys->adev->dev,
+			"found kppg(%d 0x%p), state %d pri(%d %d) fh 0x%p\n",
+			tmp0->kpg->pg->ID, tmp0, tmp0->state,
+			tmp0->pri_base, tmp0->pri_dynamic, tmp0->fh);
+
+		if (type == SCHED_START_LIST && tmp_pri > cur_pri) {
+			list_add(&kppg->sched_list, tmp0->sched_list.prev);
+			goto out;
+		} else if (type == SCHED_STOP_LIST && tmp_pri < cur_pri) {
+			list_add(&kppg->sched_list, tmp0->sched_list.prev);
+			goto out;
+		}
+	}
+
+	list_add_tail(&kppg->sched_list, &sc_list->list);
+out:
+	mutex_unlock(&sc_list->lock);
+}
+
+static int ipu_psys_detect_resource_contention(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys_resource_pool *try_res_pool;
+	struct ipu_psys *psys = kppg->fh->psys;
+	int ret = 0;
+	int state;
+
+	try_res_pool = kzalloc(sizeof(*try_res_pool), GFP_KERNEL);
+	if (IS_ERR_OR_NULL(try_res_pool))
+		return -ENOMEM;
+
+	mutex_lock(&kppg->mutex);
+	state = kppg->state;
+	mutex_unlock(&kppg->mutex);
+	if (state == PPG_STATE_STARTED || state == PPG_STATE_RUNNING ||
+	    state == PPG_STATE_RESUMED)
+		goto exit;
+
+	ret = ipu_psys_resource_pool_init(try_res_pool);
+	if (ret < 0) {
+		dev_err(&psys->adev->dev, "unable to alloc pg resources\n");
+		WARN_ON(1);
+		goto exit;
+	}
+
+	ipu_psys_resource_copy(&psys->resource_pool_running, try_res_pool);
+	ret = ipu_psys_try_allocate_resources(&psys->adev->dev,
+					      kppg->kpg->pg,
+					      kppg->manifest,
+					      try_res_pool);
+
+	ipu_psys_resource_pool_cleanup(try_res_pool);
+exit:
+	kfree(try_res_pool);
+
+	return ret;
+}
+
+static void ipu_psys_scheduler_ppg_sort(struct ipu_psys *psys, bool *stopping)
+{
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_fh *fh;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			if (kppg->state == PPG_STATE_START ||
+			    kppg->state == PPG_STATE_RESUME) {
+				ipu_psys_scheduler_add_kppg(kppg,
+							    SCHED_START_LIST);
+			} else if (kppg->state == PPG_STATE_RUNNING) {
+				ipu_psys_scheduler_add_kppg(kppg,
+							    SCHED_STOP_LIST);
+			} else if (kppg->state == PPG_STATE_SUSPENDING ||
+				   kppg->state == PPG_STATE_STOPPING) {
+				/* there are some suspending/stopping ppgs */
+				*stopping = true;
+			} else if (kppg->state == PPG_STATE_RESUMING ||
+				   kppg->state == PPG_STATE_STARTING) {
+				   /* how about kppg are resuming/starting? */
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+}
+
+static void ipu_psys_scheduler_update_start_ppg_priority(void)
+{
+	struct sched_list *sc_list = get_sc_list(SCHED_START_LIST);
+	struct ipu_psys_ppg *kppg, *tmp;
+
+	mutex_lock(&sc_list->lock);
+	if (!list_empty(&sc_list->list))
+		list_for_each_entry_safe(kppg, tmp, &sc_list->list, sched_list)
+			kppg->pri_dynamic--;
+	mutex_unlock(&sc_list->lock);
+}
+
+static bool ipu_psys_scheduler_switch_ppg(struct ipu_psys *psys)
+{
+	struct sched_list *sc_list = get_sc_list(SCHED_STOP_LIST);
+	struct ipu_psys_ppg *kppg;
+	bool resched = false;
+
+	mutex_lock(&sc_list->lock);
+	if (list_empty(&sc_list->list)) {
+		/* some ppgs are RESUMING/STARTING */
+		dev_dbg(&psys->adev->dev, "no candidated stop ppg\n");
+		mutex_unlock(&sc_list->lock);
+		return false;
+	}
+	kppg = list_first_entry(&sc_list->list, struct ipu_psys_ppg,
+				sched_list);
+	mutex_unlock(&sc_list->lock);
+
+	mutex_lock(&kppg->mutex);
+	if (!(kppg->state & PPG_STATE_STOP)) {
+		dev_dbg(&psys->adev->dev, "s_change:%s: %p %d -> %d\n",
+			__func__, kppg, kppg->state, PPG_STATE_SUSPEND);
+		kppg->state = PPG_STATE_SUSPEND;
+		resched = true;
+	}
+	mutex_unlock(&kppg->mutex);
+
+	return resched;
+}
+
+/*
+ * search all kppgs and sort them into start_list and stop_list, alway start
+ * first kppg(high priority) in start_list;
+ * if there is resource contention, it would switch kppgs in stop_list
+ * to suspend state one by one
+ */
+static bool ipu_psys_scheduler_ppg_start(struct ipu_psys *psys)
+{
+	struct sched_list *sc_list = get_sc_list(SCHED_START_LIST);
+	struct ipu_psys_ppg *kppg, *kppg0;
+	bool stopping_existed = false;
+	int ret;
+
+	ipu_psys_scheduler_ppg_sort(psys, &stopping_existed);
+
+	mutex_lock(&sc_list->lock);
+	if (list_empty(&sc_list->list)) {
+		dev_dbg(&psys->adev->dev, "no ppg to start\n");
+		mutex_unlock(&sc_list->lock);
+		return false;
+	}
+
+	list_for_each_entry_safe(kppg, kppg0,
+				 &sc_list->list, sched_list) {
+		mutex_unlock(&sc_list->lock);
+
+		ret = ipu_psys_detect_resource_contention(kppg);
+		if (ret < 0) {
+			dev_dbg(&psys->adev->dev,
+				"ppg %d resource detect failed(%d)\n",
+				kppg->kpg->pg->ID, ret);
+			/*
+			 * switch out other ppg in 2 cases:
+			 * 1. resource contention
+			 * 2. no suspending/stopping ppg
+			 */
+			if (ret == -ENOSPC) {
+				if (!stopping_existed &&
+				    ipu_psys_scheduler_switch_ppg(psys)) {
+					return true;
+				}
+				dev_dbg(&psys->adev->dev,
+					"ppg is suspending/stopping\n");
+			} else {
+				dev_err(&psys->adev->dev,
+					"detect resource error %d\n", ret);
+			}
+		} else {
+			kppg->pri_dynamic = 0;
+
+			mutex_lock(&kppg->mutex);
+			if (kppg->state == PPG_STATE_START)
+				ipu_psys_ppg_start(kppg);
+			else
+				ipu_psys_ppg_resume(kppg);
+			mutex_unlock(&kppg->mutex);
+
+			ipu_psys_scheduler_remove_kppg(kppg,
+						       SCHED_START_LIST);
+			ipu_psys_scheduler_update_start_ppg_priority();
+		}
+		mutex_lock(&sc_list->lock);
+	}
+	mutex_unlock(&sc_list->lock);
+
+	return false;
+}
+
+static bool ipu_psys_scheduler_ppg_enqueue_bufset(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg;
+	struct ipu_psys_fh *fh;
+	bool resched = false;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry(kppg, &sched->ppgs, list) {
+			if (ipu_psys_ppg_enqueue_bufsets(kppg))
+				resched = true;
+		}
+		mutex_unlock(&fh->mutex);
+	}
+
+	return resched;
+}
+
+/*
+ * This function will check all kppgs within fhs, and if kppg state
+ * is STOP or SUSPEND, l-scheduler will call ppg function to stop
+ * or suspend it and update stop list
+ */
+
+static bool ipu_psys_scheduler_ppg_halt(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+	bool stopping_exit = false;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			if (kppg->state & PPG_STATE_STOP) {
+				ipu_psys_ppg_stop(kppg);
+				ipu_psys_scheduler_remove_kppg(kppg,
+							       SCHED_STOP_LIST);
+			} else if (kppg->state == PPG_STATE_SUSPEND) {
+				ipu_psys_ppg_suspend(kppg);
+				ipu_psys_scheduler_remove_kppg(kppg,
+							       SCHED_STOP_LIST);
+			} else if (kppg->state == PPG_STATE_SUSPENDING ||
+				   kppg->state == PPG_STATE_STOPPING) {
+				stopping_exit = true;
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+	return stopping_exit;
+}
+
+static void ipu_psys_update_ppg_state_by_kcmd(struct ipu_psys *psys,
+					      struct ipu_psys_ppg *kppg,
+					      struct ipu_psys_kcmd *kcmd)
+{
+	int old_ppg_state = kppg->state;
+
+	/*
+	 * Respond kcmd when ppg is in stable state:
+	 * STARTED/RESUMED/RUNNING/SUSPENDED/STOPPED
+	 */
+	if (kppg->state == PPG_STATE_STARTED ||
+	    kppg->state == PPG_STATE_RESUMED ||
+	    kppg->state == PPG_STATE_RUNNING) {
+		if (kcmd->state == KCMD_STATE_PPG_START)
+			ipu_psys_kcmd_complete(kppg, kcmd, 0);
+		else if (kcmd->state == KCMD_STATE_PPG_STOP)
+			kppg->state = PPG_STATE_STOP;
+	} else if (kppg->state == PPG_STATE_SUSPENDED) {
+		if (kcmd->state == KCMD_STATE_PPG_START)
+			ipu_psys_kcmd_complete(kppg, kcmd, 0);
+		else if (kcmd->state == KCMD_STATE_PPG_STOP)
+			/*
+			 * Record the previous state
+			 * because here need resume at first
+			 */
+			kppg->state |= PPG_STATE_STOP;
+		else if (kcmd->state == KCMD_STATE_PPG_ENQUEUE)
+			kppg->state = PPG_STATE_RESUME;
+	} else if (kppg->state == PPG_STATE_STOPPED) {
+		if (kcmd->state == KCMD_STATE_PPG_START)
+			kppg->state = PPG_STATE_START;
+		else if (kcmd->state == KCMD_STATE_PPG_STOP)
+			ipu_psys_kcmd_complete(kppg, kcmd, 0);
+		else if (kcmd->state == KCMD_STATE_PPG_ENQUEUE) {
+			dev_err(&psys->adev->dev, "ppg %p stopped!\n", kppg);
+			ipu_psys_kcmd_complete(kppg, kcmd, -EIO);
+		}
+	}
+
+	if (old_ppg_state != kppg->state)
+		dev_dbg(&psys->adev->dev, "s_change:%s: %p %d -> %d\n",
+			__func__, kppg, old_ppg_state, kppg->state);
+}
+
+static void ipu_psys_scheduler_kcmd_set(struct ipu_psys *psys)
+{
+	struct ipu_psys_kcmd *kcmd;
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			if (list_empty(&kppg->kcmds_new_list)) {
+				mutex_unlock(&kppg->mutex);
+				continue;
+			};
+
+			kcmd = list_first_entry(&kppg->kcmds_new_list,
+						struct ipu_psys_kcmd, list);
+			ipu_psys_update_ppg_state_by_kcmd(psys, kppg, kcmd);
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+}
+
+static bool is_ready_to_enter_power_gating(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			if (!list_empty(&kppg->kcmds_new_list) ||
+			    !list_empty(&kppg->kcmds_processing_list)) {
+				mutex_unlock(&kppg->mutex);
+				mutex_unlock(&fh->mutex);
+				return false;
+			}
+			if (!(kppg->state == PPG_STATE_RUNNING ||
+			      kppg->state == PPG_STATE_STOPPED ||
+			      kppg->state == PPG_STATE_SUSPENDED)) {
+				mutex_unlock(&kppg->mutex);
+				mutex_unlock(&fh->mutex);
+				return false;
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+
+	return true;
+}
+
+static bool has_pending_kcmd(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			if (!list_empty(&kppg->kcmds_new_list) ||
+			    !list_empty(&kppg->kcmds_processing_list)) {
+				mutex_unlock(&kppg->mutex);
+				mutex_unlock(&fh->mutex);
+				return true;
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+
+	return false;
+}
+
+static bool ipu_psys_scheduler_exit_power_gating(struct ipu_psys *psys)
+{
+	/* Assume power gating process can be aborted directly during START */
+	if (psys->power_gating == PSYS_POWER_GATED) {
+		dev_dbg(&psys->adev->dev, "powergating: exit ---\n");
+		ipu_psys_exit_power_gating(psys);
+	}
+	psys->power_gating = PSYS_POWER_NORMAL;
+	return false;
+}
+
+static bool ipu_psys_scheduler_enter_power_gating(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+
+	if (!enable_power_gating)
+		return false;
+
+	if (psys->power_gating == PSYS_POWER_NORMAL &&
+	    is_ready_to_enter_power_gating(psys)) {
+		/* Enter power gating */
+		dev_dbg(&psys->adev->dev, "powergating: enter +++\n");
+		psys->power_gating = PSYS_POWER_GATING;
+	}
+
+	if (psys->power_gating != PSYS_POWER_GATING)
+		return false;
+
+	/* Suspend ppgs one by one */
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			if (kppg->state == PPG_STATE_RUNNING) {
+				kppg->state = PPG_STATE_SUSPEND;
+				mutex_unlock(&kppg->mutex);
+				mutex_unlock(&fh->mutex);
+				return true;
+			}
+
+			if (kppg->state != PPG_STATE_SUSPENDED &&
+			    kppg->state != PPG_STATE_STOPPED) {
+				/* Can't enter power gating */
+				mutex_unlock(&kppg->mutex);
+				mutex_unlock(&fh->mutex);
+				/* Need re-run l-scheduler to suspend ppg? */
+				return (kppg->state & PPG_STATE_STOP ||
+					kppg->state == PPG_STATE_SUSPEND);
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+
+	psys->power_gating = PSYS_POWER_GATED;
+	ipu_psys_enter_power_gating(psys);
+
+	return false;
+}
+
+void ipu_psys_run_next(struct ipu_psys *psys)
+{
+	/* Wake up scheduler due to unfinished work */
+	bool need_trigger = false;
+	/* Wait FW callback if there are stopping/suspending/running ppg */
+	bool wait_fw_finish = false;
+	/*
+	 * Code below will crash if fhs is empty. Normally this
+	 * shouldn't happen.
+	 */
+	if (list_empty(&psys->fhs)) {
+		WARN_ON(1);
+		return;
+	}
+
+	/* Abort power gating process */
+	if (psys->power_gating != PSYS_POWER_NORMAL &&
+	    has_pending_kcmd(psys))
+		need_trigger = ipu_psys_scheduler_exit_power_gating(psys);
+
+	/* Handle kcmd and related ppg switch */
+	if (psys->power_gating == PSYS_POWER_NORMAL) {
+		ipu_psys_scheduler_kcmd_set(psys);
+		wait_fw_finish = ipu_psys_scheduler_ppg_halt(psys);
+		need_trigger |= ipu_psys_scheduler_ppg_start(psys);
+		need_trigger |= ipu_psys_scheduler_ppg_enqueue_bufset(psys);
+	}
+	if (!(need_trigger || wait_fw_finish)) {
+		/* Nothing to do, enter power gating */
+		need_trigger = ipu_psys_scheduler_enter_power_gating(psys);
+		if (psys->power_gating == PSYS_POWER_GATING)
+			wait_fw_finish = ipu_psys_scheduler_ppg_halt(psys);
+	}
+
+	if (need_trigger && !wait_fw_finish) {
+		dev_dbg(&psys->adev->dev, "scheduler: wake up\n");
+		atomic_set(&psys->wakeup_count, 1);
+		wake_up_interruptible(&psys->sched_cmd_wq);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-platform-resources.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-platform-resources.h
@@ -0,0 +1,196 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 - 2020 Intel Corporation */
+
+#ifndef IPU6_PLATFORM_RESOURCES_H
+#define IPU6_PLATFORM_RESOURCES_H
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include "ipu-platform-resources.h"
+
+#define	IPU6_FW_PSYS_N_PADDING_UINT8_IN_PROCESS_EXT_STRUCT		0
+
+enum {
+	IPU6_FW_PSYS_CMD_QUEUE_COMMAND_ID = 0,
+	IPU6_FW_PSYS_CMD_QUEUE_DEVICE_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG0_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG1_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG2_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG3_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG4_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG5_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG6_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG7_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG8_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG9_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG10_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG11_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG12_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG13_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG14_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG15_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG16_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG17_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG18_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG19_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG20_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG21_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG22_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG23_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG24_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG25_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG26_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG27_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG28_COMMAND_ID,
+	IPU6_FW_PSYS_CMD_QUEUE_PPG29_COMMAND_ID,
+	IPU6_FW_PSYS_N_PSYS_CMD_QUEUE_ID
+};
+
+enum {
+	IPU6_FW_PSYS_TRANSFER_VMEM0_TYPE_ID = 0,
+	IPU6_FW_PSYS_TRANSFER_VMEM1_TYPE_ID,
+	IPU6_FW_PSYS_LB_VMEM_TYPE_ID,
+	IPU6_FW_PSYS_DMEM_TYPE_ID,
+	IPU6_FW_PSYS_VMEM_TYPE_ID,
+	IPU6_FW_PSYS_BAMEM_TYPE_ID,
+	IPU6_FW_PSYS_PMEM_TYPE_ID,
+	IPU6_FW_PSYS_N_MEM_TYPE_ID
+};
+
+enum ipu6_mem_id {
+	IPU6_FW_PSYS_VMEM0_ID = 0,	/* ISP0 VMEM */
+	IPU6_FW_PSYS_TRANSFER_VMEM0_ID,	/* TRANSFER VMEM 0 */
+	IPU6_FW_PSYS_TRANSFER_VMEM1_ID,	/* TRANSFER VMEM 1 */
+	IPU6_FW_PSYS_LB_VMEM_ID,	/* LB VMEM */
+	IPU6_FW_PSYS_BAMEM0_ID,	/* ISP0 BAMEM */
+	IPU6_FW_PSYS_DMEM0_ID,	/* SPC0 Dmem */
+	IPU6_FW_PSYS_DMEM1_ID,	/* SPP0 Dmem */
+	IPU6_FW_PSYS_DMEM2_ID,	/* SPP1 Dmem */
+	IPU6_FW_PSYS_DMEM3_ID,	/* ISP0 Dmem */
+	IPU6_FW_PSYS_PMEM0_ID,	/* ISP0 PMEM */
+	IPU6_FW_PSYS_N_MEM_ID
+};
+
+enum {
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT0_ID = 0,
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_READ_ID,
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_ID,
+	IPU6_FW_PSYS_DEV_CHN_DMA_INTERNAL_ID,
+	IPU6_FW_PSYS_DEV_CHN_DMA_ISA_ID,
+	IPU6_FW_PSYS_N_DEV_CHN_ID
+};
+
+enum {
+	IPU6_FW_PSYS_SP_CTRL_TYPE_ID = 0,
+	IPU6_FW_PSYS_SP_SERVER_TYPE_ID,
+	IPU6_FW_PSYS_VP_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_GDC_TYPE_ID,
+	IPU6_FW_PSYS_TNR_TYPE_ID,
+	IPU6_FW_PSYS_N_CELL_TYPE_ID
+};
+
+enum {
+	IPU6_FW_PSYS_SP0_ID = 0,
+	IPU6_FW_PSYS_VP0_ID,
+	IPU6_FW_PSYS_PSA_ACC_BNLM_ID,
+	IPU6_FW_PSYS_PSA_ACC_DM_ID,
+	IPU6_FW_PSYS_PSA_ACC_ACM_ID,
+	IPU6_FW_PSYS_PSA_ACC_GTC_YUV1_ID,
+	IPU6_FW_PSYS_BB_ACC_OFS_PIN_MAIN_ID,
+	IPU6_FW_PSYS_BB_ACC_OFS_PIN_DISPLAY_ID,
+	IPU6_FW_PSYS_BB_ACC_OFS_PIN_PP_ID,
+	IPU6_FW_PSYS_PSA_ACC_GAMMASTAR_ID,
+	IPU6_FW_PSYS_PSA_ACC_GLTM_ID,
+	IPU6_FW_PSYS_PSA_ACC_XNR_ID,
+	IPU6_FW_PSYS_PSA_VCSC_ID,	/* VCSC */
+	IPU6_FW_PSYS_ISA_ICA_ID,
+	IPU6_FW_PSYS_ISA_LSC_ID,
+	IPU6_FW_PSYS_ISA_DPC_ID,
+	IPU6_FW_PSYS_ISA_SIS_A_ID,
+	IPU6_FW_PSYS_ISA_SIS_B_ID,
+	IPU6_FW_PSYS_ISA_B2B_ID,
+	IPU6_FW_PSYS_ISA_B2R_R2I_SIE_ID,
+	IPU6_FW_PSYS_ISA_R2I_DS_A_ID,
+	IPU6_FW_PSYS_ISA_R2I_DS_B_ID,
+	IPU6_FW_PSYS_ISA_AWB_ID,
+	IPU6_FW_PSYS_ISA_AE_ID,
+	IPU6_FW_PSYS_ISA_AF_ID,
+	IPU6_FW_PSYS_ISA_DOL_ID,
+	IPU6_FW_PSYS_ISA_ICA_MEDIUM_ID,
+	IPU6_FW_PSYS_ISA_X2B_MD_ID,
+	IPU6_FW_PSYS_ISA_X2B_SVE_RGBIR_ID,
+	IPU6_FW_PSYS_ISA_PAF_ID,
+	IPU6_FW_PSYS_BB_ACC_GDC0_ID,
+	IPU6_FW_PSYS_BB_ACC_TNR_ID,
+	IPU6_FW_PSYS_N_CELL_ID
+};
+
+enum {
+	IPU6_FW_PSYS_DEV_DFM_BB_FULL_PORT_ID = 0,
+	IPU6_FW_PSYS_DEV_DFM_BB_EMPTY_PORT_ID,
+	IPU6_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID,
+	IPU6_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID,
+	IPU6_FW_PSYS_DEV_DFM_LB_FULL_PORT_ID,
+	IPU6_FW_PSYS_DEV_DFM_LB_EMPTY_PORT_ID,
+};
+
+/* Excluding PMEM */
+#define IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID	(IPU6_FW_PSYS_N_MEM_TYPE_ID - 1)
+#define IPU6_FW_PSYS_N_DEV_DFM_ID	\
+	(IPU6_FW_PSYS_DEV_DFM_LB_EMPTY_PORT_ID + 1)
+
+#define IPU6_FW_PSYS_VMEM0_MAX_SIZE		0x0800
+/* Transfer VMEM0 words, ref HAS Transfer*/
+#define IPU6_FW_PSYS_TRANSFER_VMEM0_MAX_SIZE	0x0800
+/* Transfer VMEM1 words, ref HAS Transfer*/
+#define IPU6_FW_PSYS_TRANSFER_VMEM1_MAX_SIZE	0x0800
+#define IPU6_FW_PSYS_LB_VMEM_MAX_SIZE		0x0400	/* LB VMEM words */
+#define IPU6_FW_PSYS_BAMEM0_MAX_SIZE		0x0800
+#define IPU6_FW_PSYS_DMEM0_MAX_SIZE		0x4000
+#define IPU6_FW_PSYS_DMEM1_MAX_SIZE		0x1000
+#define IPU6_FW_PSYS_DMEM2_MAX_SIZE		0x1000
+#define IPU6_FW_PSYS_DMEM3_MAX_SIZE		0x1000
+#define IPU6_FW_PSYS_PMEM0_MAX_SIZE		0x0500
+
+#define IPU6_FW_PSYS_DEV_CHN_DMA_EXT0_MAX_SIZE		30
+#define IPU6_FW_PSYS_DEV_CHN_GDC_MAX_SIZE		0
+#define IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_READ_MAX_SIZE	30
+#define IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_MAX_SIZE	43
+#define IPU6_FW_PSYS_DEV_CHN_DMA_INTERNAL_MAX_SIZE	8
+#define IPU6_FW_PSYS_DEV_CHN_DMA_IPFD_MAX_SIZE		0
+#define IPU6_FW_PSYS_DEV_CHN_DMA_ISA_MAX_SIZE		2
+
+#define IPU6_FW_PSYS_DEV_DFM_BB_FULL_PORT_ID_MAX_SIZE		32
+#define IPU6_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID_MAX_SIZE		32
+#define IPU6_FW_PSYS_DEV_DFM_LB_FULL_PORT_ID_MAX_SIZE		32
+#define IPU6_FW_PSYS_DEV_DFM_BB_EMPTY_PORT_ID_MAX_SIZE		32
+#define IPU6_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID_MAX_SIZE		32
+#define IPU6_FW_PSYS_DEV_DFM_LB_EMPTY_PORT_ID_MAX_SIZE		32
+
+struct ipu6_fw_psys_program_manifest_ext {
+	u32 dfm_port_bitmap[IPU6_FW_PSYS_N_DEV_DFM_ID];
+	u32 dfm_active_port_bitmap[IPU6_FW_PSYS_N_DEV_DFM_ID];
+	u16 ext_mem_size[IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID];
+	u16 ext_mem_offset[IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID];
+	u16 dev_chn_size[IPU6_FW_PSYS_N_DEV_CHN_ID];
+	u16 dev_chn_offset[IPU6_FW_PSYS_N_DEV_CHN_ID];
+	u8 is_dfm_relocatable[IPU6_FW_PSYS_N_DEV_DFM_ID];
+	u8 dec_resources_input[IPU_FW_PSYS_MAX_INPUT_DEC_RESOURCES];
+	u8 dec_resources_input_terminal[IPU_FW_PSYS_MAX_INPUT_DEC_RESOURCES];
+	u8 dec_resources_output[IPU_FW_PSYS_MAX_OUTPUT_DEC_RESOURCES];
+	u8 dec_resources_output_terminal[IPU_FW_PSYS_MAX_OUTPUT_DEC_RESOURCES];
+	u8 padding[IPU_FW_PSYS_N_PADDING_UINT8_IN_PROGRAM_MANIFEST_EXT];
+};
+
+struct ipu6_fw_psys_process_ext {
+	u32 dfm_port_bitmap[IPU6_FW_PSYS_N_DEV_DFM_ID];
+	u32 dfm_active_port_bitmap[IPU6_FW_PSYS_N_DEV_DFM_ID];
+	u16 ext_mem_offset[IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID];
+	u16 dev_chn_offset[IPU6_FW_PSYS_N_DEV_CHN_ID];
+	u8 ext_mem_id[IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID];
+};
+
+#endif /* IPU6_PLATFORM_RESOURCES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-ppg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-ppg.c
@@ -0,0 +1,560 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+
+#include <asm/cacheflush.h>
+
+#include "ipu6-ppg.h"
+
+static bool enable_suspend_resume;
+module_param(enable_suspend_resume, bool, 0664);
+MODULE_PARM_DESC(enable_suspend_resume, "enable fw ppg suspend/resume api");
+
+static struct ipu_psys_kcmd *
+ipu_psys_ppg_get_kcmd(struct ipu_psys_ppg *kppg, enum ipu_psys_cmd_state state)
+{
+	struct ipu_psys_kcmd *kcmd;
+
+	if (list_empty(&kppg->kcmds_new_list))
+		return NULL;
+
+	list_for_each_entry(kcmd, &kppg->kcmds_new_list, list) {
+		if (kcmd->state == state)
+			return kcmd;
+	}
+
+	return NULL;
+}
+
+struct ipu_psys_kcmd *ipu_psys_ppg_get_stop_kcmd(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys_kcmd *kcmd;
+
+	WARN(!mutex_is_locked(&kppg->mutex), "ppg locking error");
+
+	if (list_empty(&kppg->kcmds_processing_list))
+		return NULL;
+
+	list_for_each_entry(kcmd, &kppg->kcmds_processing_list, list) {
+		if (kcmd->state == KCMD_STATE_PPG_STOP)
+			return kcmd;
+	}
+
+	return NULL;
+}
+
+static struct ipu_psys_buffer_set *
+__get_buf_set(struct ipu_psys_fh *fh, size_t buf_set_size)
+{
+	struct ipu_psys_buffer_set *kbuf_set;
+	struct ipu_psys_scheduler *sched = &fh->sched;
+
+	mutex_lock(&sched->bs_mutex);
+	list_for_each_entry(kbuf_set, &sched->buf_sets, list) {
+		if (!kbuf_set->buf_set_size &&
+		    kbuf_set->size >= buf_set_size) {
+			kbuf_set->buf_set_size = buf_set_size;
+			mutex_unlock(&sched->bs_mutex);
+			return kbuf_set;
+		}
+	}
+
+	mutex_unlock(&sched->bs_mutex);
+	/* no suitable buffer available, allocate new one */
+	kbuf_set = kzalloc(sizeof(*kbuf_set), GFP_KERNEL);
+	if (!kbuf_set)
+		return NULL;
+
+	kbuf_set->kaddr = dma_alloc_attrs(&fh->psys->adev->dev,
+					  buf_set_size, &kbuf_set->dma_addr,
+					  GFP_KERNEL, 0);
+	if (!kbuf_set->kaddr) {
+		kfree(kbuf_set);
+		return NULL;
+	}
+
+	kbuf_set->buf_set_size = buf_set_size;
+	kbuf_set->size = buf_set_size;
+	mutex_lock(&sched->bs_mutex);
+	list_add(&kbuf_set->list, &sched->buf_sets);
+	mutex_unlock(&sched->bs_mutex);
+
+	return kbuf_set;
+}
+
+static struct ipu_psys_buffer_set *
+ipu_psys_create_buffer_set(struct ipu_psys_kcmd *kcmd,
+			   struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys_fh *fh = kcmd->fh;
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_buffer_set *kbuf_set;
+	size_t buf_set_size;
+	u32 *keb;
+
+	buf_set_size = ipu_fw_psys_ppg_get_buffer_set_size(kcmd);
+
+	kbuf_set = __get_buf_set(fh, buf_set_size);
+	if (!kbuf_set) {
+		dev_err(&psys->adev->dev, "failed to create buffer set\n");
+		return NULL;
+	}
+
+	kbuf_set->buf_set = ipu_fw_psys_ppg_create_buffer_set(kcmd,
+							      kbuf_set->kaddr,
+							      0);
+
+	ipu_fw_psys_ppg_buffer_set_vaddress(kbuf_set->buf_set,
+					    kbuf_set->dma_addr);
+	keb = kcmd->kernel_enable_bitmap;
+	ipu_fw_psys_ppg_buffer_set_set_kernel_enable_bitmap(kbuf_set->buf_set,
+							    keb);
+
+	return kbuf_set;
+}
+
+int ipu_psys_ppg_get_bufset(struct ipu_psys_kcmd *kcmd,
+			    struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys *psys = kppg->fh->psys;
+	struct ipu_psys_buffer_set *kbuf_set;
+	unsigned int i;
+	int ret;
+
+	kbuf_set = ipu_psys_create_buffer_set(kcmd, kppg);
+	if (!kbuf_set) {
+		ret = -EINVAL;
+		goto error;
+	}
+	kcmd->kbuf_set = kbuf_set;
+	kbuf_set->kcmd = kcmd;
+
+	for (i = 0; i < kcmd->nbuffers; i++) {
+		struct ipu_fw_psys_terminal *terminal;
+		u32 buffer;
+
+		terminal = ipu_fw_psys_pg_get_terminal(kcmd, i);
+		if (!terminal)
+			continue;
+
+		buffer = (u32)kcmd->kbufs[i]->dma_addr +
+				    kcmd->buffers[i].data_offset;
+
+		ret = ipu_fw_psys_ppg_set_buffer_set(kcmd, terminal, i, buffer);
+		if (ret) {
+			dev_err(&psys->adev->dev, "Unable to set bufset\n");
+			goto error;
+		}
+	}
+
+	return 0;
+
+error:
+	dev_err(&psys->adev->dev, "failed to get buffer set\n");
+	return ret;
+}
+
+void ipu_psys_ppg_complete(struct ipu_psys *psys, struct ipu_psys_ppg *kppg)
+{
+	u8 queue_id;
+	int old_ppg_state;
+
+	if (!psys || !kppg)
+		return;
+
+	mutex_lock(&kppg->mutex);
+	old_ppg_state = kppg->state;
+	if (kppg->state == PPG_STATE_STOPPING) {
+		struct ipu_psys_kcmd tmp_kcmd = {
+			.kpg = kppg->kpg,
+		};
+
+		kppg->state = PPG_STATE_STOPPED;
+		ipu_psys_free_resources(&kppg->kpg->resource_alloc,
+					&psys->resource_pool_running);
+		queue_id = ipu_fw_psys_ppg_get_base_queue_id(&tmp_kcmd);
+		ipu_psys_free_cmd_queue_resource(&psys->resource_pool_running,
+						 queue_id);
+		pm_runtime_put(&psys->adev->dev);
+	} else {
+		if (kppg->state == PPG_STATE_SUSPENDING) {
+			kppg->state = PPG_STATE_SUSPENDED;
+			ipu_psys_free_resources(&kppg->kpg->resource_alloc,
+						&psys->resource_pool_running);
+		} else if (kppg->state == PPG_STATE_STARTED ||
+			   kppg->state == PPG_STATE_RESUMED) {
+			kppg->state = PPG_STATE_RUNNING;
+		}
+
+		/* Kick l-scheduler thread for FW callback,
+		 * also for checking if need to enter power gating
+		 */
+		atomic_set(&psys->wakeup_count, 1);
+		wake_up_interruptible(&psys->sched_cmd_wq);
+	}
+	if (old_ppg_state != kppg->state)
+		dev_dbg(&psys->adev->dev, "s_change:%s: %p %d -> %d\n",
+			__func__, kppg, old_ppg_state, kppg->state);
+
+	mutex_unlock(&kppg->mutex);
+}
+
+int ipu_psys_ppg_start(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys *psys = kppg->fh->psys;
+	struct ipu_psys_kcmd *kcmd = ipu_psys_ppg_get_kcmd(kppg,
+						KCMD_STATE_PPG_START);
+	unsigned int i;
+	int ret;
+
+	if (!kcmd) {
+		dev_err(&psys->adev->dev, "failed to find start kcmd!\n");
+		return -EINVAL;
+	}
+
+	dev_dbg(&psys->adev->dev, "start ppg id %d, addr 0x%p\n",
+		ipu_fw_psys_pg_get_id(kcmd), kppg);
+
+	kppg->state = PPG_STATE_STARTING;
+	for (i = 0; i < kcmd->nbuffers; i++) {
+		struct ipu_fw_psys_terminal *terminal;
+
+		terminal = ipu_fw_psys_pg_get_terminal(kcmd, i);
+		if (!terminal)
+			continue;
+
+		ret = ipu_fw_psys_terminal_set(terminal, i, kcmd, 0,
+					       kcmd->buffers[i].len);
+		if (ret) {
+			dev_err(&psys->adev->dev, "Unable to set terminal\n");
+			return ret;
+		}
+	}
+
+	ret = ipu_fw_psys_pg_submit(kcmd);
+	if (ret) {
+		dev_err(&psys->adev->dev, "failed to submit kcmd!\n");
+		return ret;
+	}
+
+	ret = ipu_psys_allocate_resources(&psys->adev->dev,
+					  kcmd->kpg->pg,
+					  kcmd->pg_manifest,
+					  &kcmd->kpg->resource_alloc,
+					  &psys->resource_pool_running);
+	if (ret) {
+		dev_err(&psys->adev->dev, "alloc resources failed!\n");
+		return ret;
+	}
+
+	ret = pm_runtime_get_sync(&psys->adev->dev);
+	if (ret < 0) {
+		dev_err(&psys->adev->dev, "failed to power on psys\n");
+		goto error;
+	}
+
+	ret = ipu_psys_kcmd_start(psys, kcmd);
+	if (ret) {
+		ipu_psys_kcmd_complete(kppg, kcmd, -EIO);
+		goto error;
+	}
+
+	dev_dbg(&psys->adev->dev, "s_change:%s: %p %d -> %d\n",
+		__func__, kppg, kppg->state, PPG_STATE_STARTED);
+	kppg->state = PPG_STATE_STARTED;
+	ipu_psys_kcmd_complete(kppg, kcmd, 0);
+
+	return 0;
+
+error:
+	pm_runtime_put_noidle(&psys->adev->dev);
+	ipu_psys_reset_process_cell(&psys->adev->dev,
+				    kcmd->kpg->pg,
+				    kcmd->pg_manifest,
+				    kcmd->kpg->pg->process_count);
+	ipu_psys_free_resources(&kppg->kpg->resource_alloc,
+				&psys->resource_pool_running);
+
+	dev_err(&psys->adev->dev, "failed to start ppg\n");
+	return ret;
+}
+
+int ipu_psys_ppg_resume(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys *psys = kppg->fh->psys;
+	struct ipu_psys_kcmd tmp_kcmd = {
+		.kpg = kppg->kpg,
+		.fh = kppg->fh,
+	};
+	int ret;
+
+	dev_dbg(&psys->adev->dev, "resume ppg id %d, addr 0x%p\n",
+		ipu_fw_psys_pg_get_id(&tmp_kcmd), kppg);
+
+	kppg->state = PPG_STATE_RESUMING;
+	if (enable_suspend_resume) {
+		ret = ipu_psys_allocate_resources(&psys->adev->dev,
+						  kppg->kpg->pg,
+						  kppg->manifest,
+						  &kppg->kpg->resource_alloc,
+						  &psys->resource_pool_running);
+		if (ret) {
+			dev_err(&psys->adev->dev, "failed to allocate res\n");
+			return -EIO;
+		}
+
+		ret = ipu_fw_psys_ppg_resume(&tmp_kcmd);
+		if (ret) {
+			dev_err(&psys->adev->dev, "failed to resume ppg\n");
+			goto error;
+		}
+	} else {
+		kppg->kpg->pg->state = IPU_FW_PSYS_PROCESS_GROUP_READY;
+		ret = ipu_fw_psys_pg_submit(&tmp_kcmd);
+		if (ret) {
+			dev_err(&psys->adev->dev, "failed to submit kcmd!\n");
+			return ret;
+		}
+
+		ret = ipu_psys_allocate_resources(&psys->adev->dev,
+						  kppg->kpg->pg,
+						  kppg->manifest,
+						  &kppg->kpg->resource_alloc,
+						  &psys->resource_pool_running);
+		if (ret) {
+			dev_err(&psys->adev->dev, "failed to allocate res\n");
+			return ret;
+		}
+
+		ret = ipu_psys_kcmd_start(psys, &tmp_kcmd);
+		if (ret) {
+			dev_err(&psys->adev->dev, "failed to start kcmd!\n");
+			goto error;
+		}
+	}
+	dev_dbg(&psys->adev->dev, "s_change:%s: %p %d -> %d\n",
+		__func__, kppg, kppg->state, PPG_STATE_RESUMED);
+	kppg->state = PPG_STATE_RESUMED;
+
+	return 0;
+
+error:
+	ipu_psys_reset_process_cell(&psys->adev->dev,
+				    kppg->kpg->pg,
+				    kppg->manifest,
+				    kppg->kpg->pg->process_count);
+	ipu_psys_free_resources(&kppg->kpg->resource_alloc,
+				&psys->resource_pool_running);
+
+	return ret;
+}
+
+int ipu_psys_ppg_stop(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys_kcmd *kcmd = ipu_psys_ppg_get_kcmd(kppg,
+							   KCMD_STATE_PPG_STOP);
+	struct ipu_psys *psys = kppg->fh->psys;
+	struct ipu_psys_kcmd kcmd_temp;
+	int ppg_id, ret = 0;
+
+	if (kcmd) {
+		list_move_tail(&kcmd->list, &kppg->kcmds_processing_list);
+	} else {
+		dev_dbg(&psys->adev->dev, "Exceptional stop happened!\n");
+		kcmd_temp.kpg = kppg->kpg;
+		kcmd_temp.fh = kppg->fh;
+		kcmd = &kcmd_temp;
+		/* delete kppg in stop list to avoid this ppg resuming */
+		ipu_psys_scheduler_remove_kppg(kppg, SCHED_STOP_LIST);
+	}
+
+	ppg_id = ipu_fw_psys_pg_get_id(kcmd);
+	dev_dbg(&psys->adev->dev, "stop ppg(%d, addr 0x%p)\n", ppg_id, kppg);
+
+	if (kppg->state & PPG_STATE_SUSPENDED) {
+		if (enable_suspend_resume) {
+			dev_dbg(&psys->adev->dev, "need resume before stop!\n");
+			kcmd_temp.kpg = kppg->kpg;
+			kcmd_temp.fh = kppg->fh;
+			ret = ipu_fw_psys_ppg_resume(&kcmd_temp);
+			if (ret)
+				dev_err(&psys->adev->dev,
+					"ppg(%d) failed to resume\n", ppg_id);
+		} else if (kcmd != &kcmd_temp) {
+			ipu_psys_free_cmd_queue_resource(
+				&psys->resource_pool_running,
+				ipu_fw_psys_ppg_get_base_queue_id(kcmd));
+			ipu_psys_kcmd_complete(kppg, kcmd, 0);
+			dev_dbg(&psys->adev->dev,
+				"s_change:%s %p %d -> %d\n", __func__,
+				kppg, kppg->state, PPG_STATE_STOPPED);
+			pm_runtime_put(&psys->adev->dev);
+			kppg->state = PPG_STATE_STOPPED;
+			return 0;
+		} else {
+			return 0;
+		}
+	}
+	dev_dbg(&psys->adev->dev, "s_change:%s %p %d -> %d\n",
+		__func__, kppg, kppg->state, PPG_STATE_STOPPING);
+	kppg->state = PPG_STATE_STOPPING;
+	ret = ipu_fw_psys_pg_abort(kcmd);
+	if (ret)
+		dev_err(&psys->adev->dev, "ppg(%d) failed to abort\n", ppg_id);
+
+	return ret;
+}
+
+int ipu_psys_ppg_suspend(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys *psys = kppg->fh->psys;
+	struct ipu_psys_kcmd tmp_kcmd = {
+		.kpg = kppg->kpg,
+		.fh = kppg->fh,
+	};
+	int ppg_id = ipu_fw_psys_pg_get_id(&tmp_kcmd);
+	int ret = 0;
+
+	dev_dbg(&psys->adev->dev, "suspend ppg(%d, addr 0x%p)\n", ppg_id, kppg);
+
+	dev_dbg(&psys->adev->dev, "s_change:%s %p %d -> %d\n",
+		__func__, kppg, kppg->state, PPG_STATE_SUSPENDING);
+	kppg->state = PPG_STATE_SUSPENDING;
+	if (enable_suspend_resume)
+		ret = ipu_fw_psys_ppg_suspend(&tmp_kcmd);
+	else
+		ret = ipu_fw_psys_pg_abort(&tmp_kcmd);
+	if (ret)
+		dev_err(&psys->adev->dev, "failed to %s ppg(%d)\n",
+			enable_suspend_resume ? "suspend" : "stop", ret);
+
+	return ret;
+}
+
+static bool ipu_psys_ppg_is_bufset_existing(struct ipu_psys_ppg *kppg)
+{
+	return !list_empty(&kppg->kcmds_new_list);
+}
+
+/*
+ * ipu_psys_ppg_enqueue_bufsets - enqueue buffer sets to firmware
+ * Sometimes, if the ppg is at suspended state, this function will return true
+ * to reschedule and let the resume command scheduled before the buffer sets
+ * enqueuing.
+ */
+bool ipu_psys_ppg_enqueue_bufsets(struct ipu_psys_ppg *kppg)
+{
+	struct ipu_psys_kcmd *kcmd, *kcmd0;
+	struct ipu_psys *psys = kppg->fh->psys;
+	bool need_resume = false;
+
+	mutex_lock(&kppg->mutex);
+
+	if (kppg->state & (PPG_STATE_STARTED | PPG_STATE_RESUMED |
+			   PPG_STATE_RUNNING)) {
+		if (ipu_psys_ppg_is_bufset_existing(kppg)) {
+			list_for_each_entry_safe(kcmd, kcmd0,
+						 &kppg->kcmds_new_list, list) {
+				int ret;
+
+				if (kcmd->state != KCMD_STATE_PPG_ENQUEUE) {
+					need_resume = true;
+					break;
+				}
+
+				ret = ipu_fw_psys_ppg_enqueue_bufs(kcmd);
+				if (ret) {
+					dev_err(&psys->adev->dev,
+						"kppg 0x%p fail to qbufset %d",
+						kppg, ret);
+					break;
+				}
+				list_move_tail(&kcmd->list,
+					       &kppg->kcmds_processing_list);
+				dev_dbg(&psys->adev->dev,
+					"kppg %d %p queue kcmd 0x%p fh 0x%p\n",
+					ipu_fw_psys_pg_get_id(kcmd),
+					kppg, kcmd, kcmd->fh);
+			}
+		}
+	}
+
+	mutex_unlock(&kppg->mutex);
+	return need_resume;
+}
+
+void ipu_psys_enter_power_gating(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+	int ret = 0;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			/*
+			 * Only for SUSPENDED kppgs, STOPPED kppgs has already
+			 * power down and new kppgs might come now.
+			 */
+			if (kppg->state != PPG_STATE_SUSPENDED) {
+				mutex_unlock(&kppg->mutex);
+				continue;
+			}
+
+			ret = pm_runtime_put_autosuspend(&psys->adev->dev);
+			if (ret < 0) {
+				dev_err(&psys->adev->dev,
+					"failed to power gating off\n");
+				pm_runtime_get_sync(&psys->adev->dev);
+
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+}
+
+void ipu_psys_exit_power_gating(struct ipu_psys *psys)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+	int ret = 0;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		mutex_lock(&fh->mutex);
+		sched = &fh->sched;
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			/* Only for SUSPENDED kppgs */
+			if (kppg->state != PPG_STATE_SUSPENDED) {
+				mutex_unlock(&kppg->mutex);
+				continue;
+			}
+
+			ret = pm_runtime_get_sync(&psys->adev->dev);
+			if (ret < 0) {
+				dev_err(&psys->adev->dev,
+					"failed to power gating\n");
+				pm_runtime_put_noidle(&psys->adev->dev);
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-ppg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-ppg.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 Intel Corporation
+ */
+
+#ifndef IPU6_PPG_H
+#define IPU6_PPG_H
+
+#include "ipu-psys.h"
+/* starting from '2' in case of someone passes true or false */
+enum SCHED_LIST {
+	SCHED_START_LIST = 2,
+	SCHED_STOP_LIST
+};
+
+enum ipu_psys_power_gating_state {
+	PSYS_POWER_NORMAL = 0,
+	PSYS_POWER_GATING,
+	PSYS_POWER_GATED
+};
+
+int ipu_psys_ppg_get_bufset(struct ipu_psys_kcmd *kcmd,
+			    struct ipu_psys_ppg *kppg);
+struct ipu_psys_kcmd *ipu_psys_ppg_get_stop_kcmd(struct ipu_psys_ppg *kppg);
+void ipu_psys_scheduler_remove_kppg(struct ipu_psys_ppg *kppg,
+				    enum SCHED_LIST type);
+void ipu_psys_scheduler_add_kppg(struct ipu_psys_ppg *kppg,
+				 enum SCHED_LIST type);
+int ipu_psys_ppg_start(struct ipu_psys_ppg *kppg);
+int ipu_psys_ppg_resume(struct ipu_psys_ppg *kppg);
+int ipu_psys_ppg_stop(struct ipu_psys_ppg *kppg);
+int ipu_psys_ppg_suspend(struct ipu_psys_ppg *kppg);
+void ipu_psys_ppg_complete(struct ipu_psys *psys, struct ipu_psys_ppg *kppg);
+bool ipu_psys_ppg_enqueue_bufsets(struct ipu_psys_ppg *kppg);
+void ipu_psys_enter_power_gating(struct ipu_psys *psys);
+void ipu_psys_exit_power_gating(struct ipu_psys *psys);
+
+#endif /* IPU6_PPG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-psys-gpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-psys-gpc.c
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+#include <linux/pm_runtime.h>
+
+#include "ipu-psys.h"
+#include "ipu-platform-regs.h"
+
+/*
+ * GPC (Gerneral Performance Counters)
+ */
+#define IPU_PSYS_GPC_NUM 16
+
+#ifndef CONFIG_PM
+#define pm_runtime_get_sync(d)			0
+#define pm_runtime_put(d)			0
+#endif
+
+struct ipu_psys_gpc {
+	bool enable;
+	unsigned int route;
+	unsigned int source;
+	unsigned int sense;
+	unsigned int gpcindex;
+	void *prit;
+};
+
+struct ipu_psys_gpcs {
+	bool gpc_enable;
+	struct ipu_psys_gpc gpc[IPU_PSYS_GPC_NUM];
+	void *prit;
+};
+
+static int ipu6_psys_gpc_global_enable_get(void *data, u64 *val)
+{
+	struct ipu_psys_gpcs *psys_gpcs = data;
+	struct ipu_psys *psys = psys_gpcs->prit;
+
+	mutex_lock(&psys->mutex);
+
+	*val = psys_gpcs->gpc_enable;
+
+	mutex_unlock(&psys->mutex);
+	return 0;
+}
+
+static int ipu6_psys_gpc_global_enable_set(void *data, u64 val)
+{
+	struct ipu_psys_gpcs *psys_gpcs = data;
+	struct ipu_psys *psys = psys_gpcs->prit;
+	void __iomem *base;
+	int idx, res;
+
+	if (val != 0 && val != 1)
+		return -EINVAL;
+
+	if (!psys || !psys->pdata || !psys->pdata->base)
+		return -EINVAL;
+
+	mutex_lock(&psys->mutex);
+
+	base = psys->pdata->base + IPU_GPC_BASE;
+
+	res = pm_runtime_get_sync(&psys->adev->dev);
+	if (res < 0) {
+		pm_runtime_put(&psys->adev->dev);
+		mutex_unlock(&psys->mutex);
+		return res;
+	}
+
+	if (val == 0) {
+		writel(0x0, base + IPU_GPREG_TRACE_TIMER_RST);
+		writel(0x0, base + IPU_CDC_MMU_GPC_OVERALL_ENABLE);
+		writel(0xffff, base + IPU_CDC_MMU_GPC_SOFT_RESET);
+		psys_gpcs->gpc_enable = false;
+		for (idx = 0; idx < IPU_PSYS_GPC_NUM; idx++) {
+			psys_gpcs->gpc[idx].enable = 0;
+			psys_gpcs->gpc[idx].sense = 0;
+			psys_gpcs->gpc[idx].route = 0;
+			psys_gpcs->gpc[idx].source = 0;
+		}
+		pm_runtime_mark_last_busy(&psys->adev->dev);
+		pm_runtime_put_autosuspend(&psys->adev->dev);
+	} else {
+		/* Set gpc reg and start all gpc here.
+		 * RST free running local timer.
+		 */
+		writel(0x0, base + IPU_GPREG_TRACE_TIMER_RST);
+		writel(0x1, base + IPU_GPREG_TRACE_TIMER_RST);
+
+		for (idx = 0; idx < IPU_PSYS_GPC_NUM; idx++) {
+			/* Enable */
+			writel(psys_gpcs->gpc[idx].enable,
+			       base + IPU_CDC_MMU_GPC_ENABLE0 + 4 * idx);
+			/* Setting (route/source/sense) */
+			writel((psys_gpcs->gpc[idx].sense
+					<< IPU_GPC_SENSE_OFFSET)
+				+ (psys_gpcs->gpc[idx].route
+					<< IPU_GPC_ROUTE_OFFSET)
+				+ (psys_gpcs->gpc[idx].source
+					<< IPU_GPC_SOURCE_OFFSET),
+				base + IPU_CDC_MMU_GPC_CNT_SEL0 + 4 * idx);
+		}
+
+		/* Soft reset and Overall Enable. */
+		writel(0x0, base + IPU_CDC_MMU_GPC_OVERALL_ENABLE);
+		writel(0xffff, base + IPU_CDC_MMU_GPC_SOFT_RESET);
+		writel(0x1, base + IPU_CDC_MMU_GPC_OVERALL_ENABLE);
+
+		psys_gpcs->gpc_enable = true;
+	}
+
+	mutex_unlock(&psys->mutex);
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(psys_gpc_globe_enable_fops,
+			ipu6_psys_gpc_global_enable_get,
+			ipu6_psys_gpc_global_enable_set, "%llu\n");
+
+static int ipu6_psys_gpc_count_get(void *data, u64 *val)
+{
+	struct ipu_psys_gpc *psys_gpc = data;
+	struct ipu_psys *psys = psys_gpc->prit;
+	void __iomem *base;
+	int res;
+
+	if (!psys || !psys->pdata || !psys->pdata->base)
+		return -EINVAL;
+
+	mutex_lock(&psys->mutex);
+
+	base = psys->pdata->base + IPU_GPC_BASE;
+
+	res = pm_runtime_get_sync(&psys->adev->dev);
+	if (res < 0) {
+		pm_runtime_put(&psys->adev->dev);
+		mutex_unlock(&psys->mutex);
+		return res;
+	}
+
+	*val = readl(base + IPU_CDC_MMU_GPC_VALUE0 + 4 * psys_gpc->gpcindex);
+
+	mutex_unlock(&psys->mutex);
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(psys_gpc_count_fops,
+			ipu6_psys_gpc_count_get,
+			NULL, "%llu\n");
+
+int ipu_psys_gpc_init_debugfs(struct ipu_psys *psys)
+{
+	struct dentry *gpcdir;
+	struct dentry *dir;
+	struct dentry *file;
+	int idx;
+	char gpcname[10];
+	struct ipu_psys_gpcs *psys_gpcs;
+
+	psys_gpcs = devm_kzalloc(&psys->dev, sizeof(*psys_gpcs), GFP_KERNEL);
+	if (!psys_gpcs)
+		return -ENOMEM;
+
+	gpcdir = debugfs_create_dir("gpc", psys->debugfsdir);
+	if (IS_ERR(gpcdir))
+		return -ENOMEM;
+
+	psys_gpcs->prit = psys;
+	file = debugfs_create_file("enable", 0600, gpcdir, psys_gpcs,
+				   &psys_gpc_globe_enable_fops);
+	if (IS_ERR(file))
+		goto err;
+
+	for (idx = 0; idx < IPU_PSYS_GPC_NUM; idx++) {
+		sprintf(gpcname, "gpc%d", idx);
+		dir = debugfs_create_dir(gpcname, gpcdir);
+		if (IS_ERR(dir))
+			goto err;
+
+		debugfs_create_bool("enable", 0600, dir,
+				    &psys_gpcs->gpc[idx].enable);
+
+		debugfs_create_u32("source", 0600, dir,
+				   &psys_gpcs->gpc[idx].source);
+
+		debugfs_create_u32("route", 0600, dir,
+				   &psys_gpcs->gpc[idx].route);
+
+		debugfs_create_u32("sense", 0600, dir,
+				   &psys_gpcs->gpc[idx].sense);
+
+		psys_gpcs->gpc[idx].gpcindex = idx;
+		psys_gpcs->gpc[idx].prit = psys;
+		file = debugfs_create_file("count", 0400, dir,
+					   &psys_gpcs->gpc[idx],
+					   &psys_gpc_count_fops);
+		if (IS_ERR(file))
+			goto err;
+	}
+
+	return 0;
+
+err:
+	debugfs_remove_recursive(gpcdir);
+	return -ENOMEM;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6-psys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6-psys.c
@@ -0,0 +1,1032 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#include <linux/uaccess.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/mm.h>
+#include <linux/pm_runtime.h>
+#include <linux/kthread.h>
+#include <linux/init_task.h>
+#include <linux/version.h>
+#include <uapi/linux/sched/types.h>
+#include <linux/module.h>
+#include <linux/fs.h>
+
+#include "ipu.h"
+#include "ipu-psys.h"
+#include "ipu6-ppg.h"
+#include "ipu-platform-regs.h"
+#include "ipu-trace.h"
+
+static bool early_pg_transfer;
+module_param(early_pg_transfer, bool, 0664);
+MODULE_PARM_DESC(early_pg_transfer,
+		 "Copy PGs back to user after resource allocation");
+
+bool enable_power_gating = true;
+module_param(enable_power_gating, bool, 0664);
+MODULE_PARM_DESC(enable_power_gating, "enable power gating");
+
+struct ipu_trace_block psys_trace_blocks[] = {
+	{
+		.offset = IPU_TRACE_REG_PS_TRACE_UNIT_BASE,
+		.type = IPU_TRACE_BLOCK_TUN,
+	},
+	{
+		.offset = IPU_TRACE_REG_PS_SPC_EVQ_BASE,
+		.type = IPU_TRACE_BLOCK_TM,
+	},
+	{
+		.offset = IPU_TRACE_REG_PS_SPP0_EVQ_BASE,
+		.type = IPU_TRACE_BLOCK_TM,
+	},
+	{
+		.offset = IPU_TRACE_REG_PS_SPC_GPC_BASE,
+		.type = IPU_TRACE_BLOCK_GPC,
+	},
+	{
+		.offset = IPU_TRACE_REG_PS_SPP0_GPC_BASE,
+		.type = IPU_TRACE_BLOCK_GPC,
+	},
+	{
+		.offset = IPU_TRACE_REG_PS_MMU_GPC_BASE,
+		.type = IPU_TRACE_BLOCK_GPC,
+	},
+	{
+		.offset = IPU_TRACE_REG_PS_GPREG_TRACE_TIMER_RST_N,
+		.type = IPU_TRACE_TIMER_RST,
+	},
+	{
+		.type = IPU_TRACE_BLOCK_END,
+	}
+};
+
+static void ipu6_set_sp_info_bits(void *base)
+{
+	int i;
+
+	writel(IPU_INFO_REQUEST_DESTINATION_IOSF,
+	       base + IPU_REG_PSYS_INFO_SEG_0_CONFIG_ICACHE_MASTER);
+
+	for (i = 0; i < 4; i++)
+		writel(IPU_INFO_REQUEST_DESTINATION_IOSF,
+		       base + IPU_REG_PSYS_INFO_SEG_CMEM_MASTER(i));
+	for (i = 0; i < 4; i++)
+		writel(IPU_INFO_REQUEST_DESTINATION_IOSF,
+		       base + IPU_REG_PSYS_INFO_SEG_XMEM_MASTER(i));
+}
+
+#define PSYS_SUBDOMAINS_STATUS_WAIT_COUNT        1000
+void ipu_psys_subdomains_power(struct ipu_psys *psys, bool on)
+{
+	unsigned int i;
+	u32 val;
+
+	/* power domain req */
+	dev_dbg(&psys->adev->dev, "power %s psys sub-domains",
+		on ? "UP" : "DOWN");
+	if (on)
+		writel(IPU_PSYS_SUBDOMAINS_POWER_MASK,
+		       psys->adev->isp->base + IPU_PSYS_SUBDOMAINS_POWER_REQ);
+	else
+		writel(0x0,
+		       psys->adev->isp->base + IPU_PSYS_SUBDOMAINS_POWER_REQ);
+
+	i = 0;
+	do {
+		usleep_range(10, 20);
+		val = readl(psys->adev->isp->base +
+			    IPU_PSYS_SUBDOMAINS_POWER_STATUS);
+		if (!(val & BIT(31))) {
+			dev_dbg(&psys->adev->dev,
+				"PS sub-domains req done with status 0x%x",
+				val);
+			break;
+		}
+		i++;
+	} while (i < PSYS_SUBDOMAINS_STATUS_WAIT_COUNT);
+
+	if (i == PSYS_SUBDOMAINS_STATUS_WAIT_COUNT)
+		dev_warn(&psys->adev->dev, "Psys sub-domains %s req timeout!",
+			 on ? "UP" : "DOWN");
+}
+
+void ipu_psys_setup_hw(struct ipu_psys *psys)
+{
+	void __iomem *base = psys->pdata->base;
+	void __iomem *spc_regs_base =
+	    base + psys->pdata->ipdata->hw_variant.spc_offset;
+	void *psys_iommu0_ctrl;
+	u32 irqs;
+	const u8 r3 = IPU_DEVICE_AB_GROUP1_TARGET_ID_R3_SPC_STATUS_REG;
+	const u8 r4 = IPU_DEVICE_AB_GROUP1_TARGET_ID_R4_SPC_MASTER_BASE_ADDR;
+	const u8 r5 = IPU_DEVICE_AB_GROUP1_TARGET_ID_R5_SPC_PC_STALL;
+
+	if (!psys->adev->isp->secure_mode) {
+		/* configure access blocker for non-secure mode */
+		writel(NCI_AB_ACCESS_MODE_RW,
+		       base + IPU_REG_DMA_TOP_AB_GROUP1_BASE_ADDR +
+		       IPU_REG_DMA_TOP_AB_RING_ACCESS_OFFSET(r3));
+		writel(NCI_AB_ACCESS_MODE_RW,
+		       base + IPU_REG_DMA_TOP_AB_GROUP1_BASE_ADDR +
+		       IPU_REG_DMA_TOP_AB_RING_ACCESS_OFFSET(r4));
+		writel(NCI_AB_ACCESS_MODE_RW,
+		       base + IPU_REG_DMA_TOP_AB_GROUP1_BASE_ADDR +
+		       IPU_REG_DMA_TOP_AB_RING_ACCESS_OFFSET(r5));
+	}
+	psys_iommu0_ctrl = base +
+		psys->pdata->ipdata->hw_variant.mmu_hw[0].offset +
+		IPU_MMU_INFO_OFFSET;
+	writel(IPU_INFO_REQUEST_DESTINATION_IOSF, psys_iommu0_ctrl);
+
+	ipu6_set_sp_info_bits(spc_regs_base + IPU_PSYS_REG_SPC_STATUS_CTRL);
+	ipu6_set_sp_info_bits(spc_regs_base + IPU_PSYS_REG_SPP0_STATUS_CTRL);
+
+	/* Enable FW interrupt #0 */
+	writel(0, base + IPU_REG_PSYS_GPDEV_FWIRQ(0));
+	irqs = IPU_PSYS_GPDEV_IRQ_FWIRQ(IPU_PSYS_GPDEV_FWIRQ0);
+	writel(irqs, base + IPU_REG_PSYS_GPDEV_IRQ_EDGE);
+	writel(irqs, base + IPU_REG_PSYS_GPDEV_IRQ_LEVEL_NOT_PULSE);
+	writel(0xffffffff, base + IPU_REG_PSYS_GPDEV_IRQ_CLEAR);
+	writel(irqs, base + IPU_REG_PSYS_GPDEV_IRQ_MASK);
+	writel(irqs, base + IPU_REG_PSYS_GPDEV_IRQ_ENABLE);
+}
+
+static struct ipu_psys_ppg *ipu_psys_identify_kppg(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_psys_scheduler *sched = &kcmd->fh->sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+
+	mutex_lock(&kcmd->fh->mutex);
+	if (list_empty(&sched->ppgs))
+		goto not_found;
+
+	list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+		if (ipu_fw_psys_pg_get_token(kcmd)
+		    != kppg->token)
+			continue;
+		mutex_unlock(&kcmd->fh->mutex);
+		return kppg;
+	}
+
+not_found:
+	mutex_unlock(&kcmd->fh->mutex);
+	return NULL;
+}
+
+/*
+ * Called to free up all resources associated with a kcmd.
+ * After this the kcmd doesn't anymore exist in the driver.
+ */
+static void ipu_psys_kcmd_free(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_psys_ppg *kppg;
+	struct ipu_psys_scheduler *sched;
+
+	if (!kcmd)
+		return;
+
+	kppg = ipu_psys_identify_kppg(kcmd);
+	sched = &kcmd->fh->sched;
+
+	if (kcmd->kbuf_set) {
+		mutex_lock(&sched->bs_mutex);
+		kcmd->kbuf_set->buf_set_size = 0;
+		mutex_unlock(&sched->bs_mutex);
+		kcmd->kbuf_set = NULL;
+	}
+
+	if (kppg) {
+		mutex_lock(&kppg->mutex);
+		if (!list_empty(&kcmd->list))
+			list_del(&kcmd->list);
+		mutex_unlock(&kppg->mutex);
+	}
+
+	kfree(kcmd->pg_manifest);
+	kfree(kcmd->kbufs);
+	kfree(kcmd->buffers);
+	kfree(kcmd);
+}
+
+static struct ipu_psys_kcmd *ipu_psys_copy_cmd(struct ipu_psys_command *cmd,
+					       struct ipu_psys_fh *fh)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_kcmd *kcmd;
+	struct ipu_psys_kbuffer *kpgbuf;
+	unsigned int i;
+	int ret, prevfd, fd;
+
+	fd = prevfd = -1;
+
+	if (cmd->bufcount > IPU_MAX_PSYS_CMD_BUFFERS)
+		return NULL;
+
+	if (!cmd->pg_manifest_size)
+		return NULL;
+
+	kcmd = kzalloc(sizeof(*kcmd), GFP_KERNEL);
+	if (!kcmd)
+		return NULL;
+
+	kcmd->state = KCMD_STATE_PPG_NEW;
+	kcmd->fh = fh;
+	INIT_LIST_HEAD(&kcmd->list);
+
+	mutex_lock(&fh->mutex);
+	fd = cmd->pg;
+	kpgbuf = ipu_psys_lookup_kbuffer(fh, fd);
+	if (!kpgbuf || !kpgbuf->sgt) {
+		dev_err(&psys->adev->dev, "%s kbuf %p with fd %d not found.\n",
+			__func__, kpgbuf, fd);
+		mutex_unlock(&fh->mutex);
+		goto error;
+	}
+
+	/* check and remap if possibe */
+	ret = ipu_psys_mapbuf_locked(fd, fh, kpgbuf);
+	if (ret) {
+		dev_err(&psys->adev->dev, "%s remap failed\n", __func__);
+		mutex_unlock(&fh->mutex);
+		goto error;
+	}
+
+	kpgbuf = ipu_psys_lookup_kbuffer(fh, fd);
+	if (!kpgbuf || !kpgbuf->sgt) {
+		WARN(1, "kbuf not found or unmapped.\n");
+		mutex_unlock(&fh->mutex);
+		goto error;
+	}
+	mutex_unlock(&fh->mutex);
+
+	kcmd->pg_user = kpgbuf->kaddr;
+	kcmd->kpg = __get_pg_buf(psys, kpgbuf->len);
+	if (!kcmd->kpg)
+		goto error;
+
+	memcpy(kcmd->kpg->pg, kcmd->pg_user, kcmd->kpg->pg_size);
+
+	kcmd->pg_manifest = kzalloc(cmd->pg_manifest_size, GFP_KERNEL);
+	if (!kcmd->pg_manifest)
+		goto error;
+
+	ret = copy_from_user(kcmd->pg_manifest, cmd->pg_manifest,
+			     cmd->pg_manifest_size);
+	if (ret)
+		goto error;
+
+	kcmd->pg_manifest_size = cmd->pg_manifest_size;
+
+	kcmd->user_token = cmd->user_token;
+	kcmd->issue_id = cmd->issue_id;
+	kcmd->priority = cmd->priority;
+	if (kcmd->priority >= IPU_PSYS_CMD_PRIORITY_NUM)
+		goto error;
+
+	/*
+	 * Kenel enable bitmap be used only.
+	 */
+	memcpy(kcmd->kernel_enable_bitmap, cmd->kernel_enable_bitmap,
+	       sizeof(cmd->kernel_enable_bitmap));
+
+	kcmd->nbuffers = ipu_fw_psys_pg_get_terminal_count(kcmd);
+	kcmd->buffers = kcalloc(kcmd->nbuffers, sizeof(*kcmd->buffers),
+				GFP_KERNEL);
+	if (!kcmd->buffers)
+		goto error;
+
+	kcmd->kbufs = kcalloc(kcmd->nbuffers, sizeof(kcmd->kbufs[0]),
+			      GFP_KERNEL);
+	if (!kcmd->kbufs)
+		goto error;
+
+	/* should be stop cmd for ppg */
+	if (!cmd->buffers) {
+		kcmd->state = KCMD_STATE_PPG_STOP;
+		return kcmd;
+	}
+
+	if (!cmd->bufcount || kcmd->nbuffers > cmd->bufcount)
+		goto error;
+
+	ret = copy_from_user(kcmd->buffers, cmd->buffers,
+			     kcmd->nbuffers * sizeof(*kcmd->buffers));
+	if (ret)
+		goto error;
+
+	for (i = 0; i < kcmd->nbuffers; i++) {
+		struct ipu_fw_psys_terminal *terminal;
+
+		terminal = ipu_fw_psys_pg_get_terminal(kcmd, i);
+		if (!terminal)
+			continue;
+
+		if (!(kcmd->buffers[i].flags & IPU_BUFFER_FLAG_DMA_HANDLE)) {
+			kcmd->state = KCMD_STATE_PPG_START;
+			continue;
+		}
+		if (kcmd->state == KCMD_STATE_PPG_START) {
+			dev_err(&psys->adev->dev,
+				"err: all buffer.flags&DMA_HANDLE must 0\n");
+			goto error;
+		}
+
+		mutex_lock(&fh->mutex);
+		fd = kcmd->buffers[i].base.fd;
+		kpgbuf = ipu_psys_lookup_kbuffer(fh, fd);
+		if (!kpgbuf || !kpgbuf->sgt) {
+			dev_err(&psys->adev->dev,
+				"%s kcmd->buffers[%d] %p fd %d not found.\n",
+				__func__, i, kpgbuf, fd);
+			mutex_unlock(&fh->mutex);
+			goto error;
+		}
+
+		ret = ipu_psys_mapbuf_locked(fd, fh, kpgbuf);
+		if (ret) {
+			dev_err(&psys->adev->dev, "%s remap failed\n",
+				__func__);
+			mutex_unlock(&fh->mutex);
+			goto error;
+		}
+
+		kpgbuf = ipu_psys_lookup_kbuffer(fh, fd);
+		if (!kpgbuf || !kpgbuf->sgt) {
+			WARN(1, "kbuf not found or unmapped.\n");
+			mutex_unlock(&fh->mutex);
+			goto error;
+		}
+		mutex_unlock(&fh->mutex);
+		kcmd->kbufs[i] = kpgbuf;
+		if (!kcmd->kbufs[i] || !kcmd->kbufs[i]->sgt ||
+		    kcmd->kbufs[i]->len < kcmd->buffers[i].bytes_used)
+			goto error;
+		if ((kcmd->kbufs[i]->flags &
+		     IPU_BUFFER_FLAG_NO_FLUSH) ||
+		    (kcmd->buffers[i].flags &
+		     IPU_BUFFER_FLAG_NO_FLUSH) ||
+		    prevfd == kcmd->buffers[i].base.fd)
+			continue;
+
+		prevfd = kcmd->buffers[i].base.fd;
+		dma_sync_sg_for_device(&psys->adev->dev,
+				       kcmd->kbufs[i]->sgt->sgl,
+				       kcmd->kbufs[i]->sgt->orig_nents,
+				       DMA_BIDIRECTIONAL);
+	}
+
+	if (kcmd->state != KCMD_STATE_PPG_START)
+		kcmd->state = KCMD_STATE_PPG_ENQUEUE;
+
+	return kcmd;
+error:
+	ipu_psys_kcmd_free(kcmd);
+
+	dev_dbg(&psys->adev->dev, "failed to copy cmd\n");
+
+	return NULL;
+}
+
+static struct ipu_psys_buffer_set *
+ipu_psys_lookup_kbuffer_set(struct ipu_psys *psys, u32 addr)
+{
+	struct ipu_psys_fh *fh;
+	struct ipu_psys_buffer_set *kbuf_set;
+	struct ipu_psys_scheduler *sched;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		sched = &fh->sched;
+		mutex_lock(&sched->bs_mutex);
+		list_for_each_entry(kbuf_set, &sched->buf_sets, list) {
+			if (kbuf_set->buf_set &&
+			    kbuf_set->buf_set->ipu_virtual_address == addr) {
+				mutex_unlock(&sched->bs_mutex);
+				return kbuf_set;
+			}
+		}
+		mutex_unlock(&sched->bs_mutex);
+	}
+
+	return NULL;
+}
+
+static struct ipu_psys_ppg *ipu_psys_lookup_ppg(struct ipu_psys *psys,
+						dma_addr_t pg_addr)
+{
+	struct ipu_psys_scheduler *sched;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_fh *fh;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		sched = &fh->sched;
+		mutex_lock(&fh->mutex);
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			if (pg_addr != kppg->kpg->pg_dma_addr)
+				continue;
+			mutex_unlock(&fh->mutex);
+			return kppg;
+		}
+		mutex_unlock(&fh->mutex);
+	}
+
+	return NULL;
+}
+
+/*
+ * Move kcmd into completed state (due to running finished or failure).
+ * Fill up the event struct and notify waiters.
+ */
+void ipu_psys_kcmd_complete(struct ipu_psys_ppg *kppg,
+			    struct ipu_psys_kcmd *kcmd, int error)
+{
+	struct ipu_psys_fh *fh = kcmd->fh;
+	struct ipu_psys *psys = fh->psys;
+
+	kcmd->ev.type = IPU_PSYS_EVENT_TYPE_CMD_COMPLETE;
+	kcmd->ev.user_token = kcmd->user_token;
+	kcmd->ev.issue_id = kcmd->issue_id;
+	kcmd->ev.error = error;
+	list_move_tail(&kcmd->list, &kppg->kcmds_finished_list);
+
+	if (kcmd->constraint.min_freq)
+		ipu_buttress_remove_psys_constraint(psys->adev->isp,
+						    &kcmd->constraint);
+
+	if (!early_pg_transfer && kcmd->pg_user && kcmd->kpg->pg) {
+		struct ipu_psys_kbuffer *kbuf;
+
+		kbuf = ipu_psys_lookup_kbuffer_by_kaddr(kcmd->fh,
+							kcmd->pg_user);
+		if (kbuf && kbuf->valid)
+			memcpy(kcmd->pg_user,
+			       kcmd->kpg->pg, kcmd->kpg->pg_size);
+		else
+			dev_dbg(&psys->adev->dev, "Skipping unmapped buffer\n");
+	}
+
+	kcmd->state = KCMD_STATE_PPG_COMPLETE;
+	wake_up_interruptible(&fh->wait);
+}
+
+/*
+ * Submit kcmd into psys queue. If running fails, complete the kcmd
+ * with an error.
+ *
+ * Found a runnable PG. Move queue to the list tail for round-robin
+ * scheduling and run the PG. Start the watchdog timer if the PG was
+ * started successfully. Enable PSYS power if requested.
+ */
+int ipu_psys_kcmd_start(struct ipu_psys *psys, struct ipu_psys_kcmd *kcmd)
+{
+	int ret;
+
+	if (psys->adev->isp->flr_done)
+		return -EIO;
+
+	if (early_pg_transfer && kcmd->pg_user && kcmd->kpg->pg)
+		memcpy(kcmd->pg_user, kcmd->kpg->pg, kcmd->kpg->pg_size);
+
+	ret = ipu_fw_psys_pg_start(kcmd);
+	if (ret) {
+		dev_err(&psys->adev->dev, "failed to start kcmd!\n");
+		return ret;
+	}
+
+	ipu_fw_psys_pg_dump(psys, kcmd, "run");
+
+	ret = ipu_fw_psys_pg_disown(kcmd);
+	if (ret) {
+		dev_err(&psys->adev->dev, "failed to start kcmd!\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ipu_psys_kcmd_send_to_ppg_start(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_psys_fh *fh = kcmd->fh;
+	struct ipu_psys_scheduler *sched = &fh->sched;
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_ppg *kppg;
+	struct ipu_psys_resource_pool *rpr;
+	int queue_id;
+	int ret;
+
+	rpr = &psys->resource_pool_running;
+
+	kppg = kzalloc(sizeof(*kppg), GFP_KERNEL);
+	if (!kppg)
+		return -ENOMEM;
+
+	kppg->fh = fh;
+	kppg->kpg = kcmd->kpg;
+	kppg->state = PPG_STATE_START;
+	kppg->pri_base = kcmd->priority;
+	kppg->pri_dynamic = 0;
+	INIT_LIST_HEAD(&kppg->list);
+
+	mutex_init(&kppg->mutex);
+	INIT_LIST_HEAD(&kppg->kcmds_new_list);
+	INIT_LIST_HEAD(&kppg->kcmds_processing_list);
+	INIT_LIST_HEAD(&kppg->kcmds_finished_list);
+	INIT_LIST_HEAD(&kppg->sched_list);
+
+	kppg->manifest = kzalloc(kcmd->pg_manifest_size, GFP_KERNEL);
+	if (!kppg->manifest) {
+		kfree(kppg);
+		return -ENOMEM;
+	}
+	memcpy(kppg->manifest, kcmd->pg_manifest,
+	       kcmd->pg_manifest_size);
+
+	queue_id = ipu_psys_allocate_cmd_queue_resource(rpr);
+	if (queue_id == -ENOSPC) {
+		dev_err(&psys->adev->dev, "no available queue\n");
+		kfree(kppg->manifest);
+		kfree(kppg);
+		mutex_unlock(&psys->mutex);
+		return -ENOMEM;
+	}
+
+	/*
+	 * set token as start cmd will immediately be followed by a
+	 * enqueue cmd so that kppg could be retrieved.
+	 */
+	kppg->token = (u64)kcmd->kpg;
+	ipu_fw_psys_pg_set_token(kcmd, kppg->token);
+	ipu_fw_psys_ppg_set_base_queue_id(kcmd, queue_id);
+	ret = ipu_fw_psys_pg_set_ipu_vaddress(kcmd,
+					      kcmd->kpg->pg_dma_addr);
+	if (ret) {
+		ipu_psys_free_cmd_queue_resource(rpr, queue_id);
+		kfree(kppg->manifest);
+		kfree(kppg);
+		return -EIO;
+	}
+	memcpy(kcmd->pg_user, kcmd->kpg->pg, kcmd->kpg->pg_size);
+
+	mutex_lock(&fh->mutex);
+	list_add_tail(&kppg->list, &sched->ppgs);
+	mutex_unlock(&fh->mutex);
+
+	mutex_lock(&kppg->mutex);
+	list_add(&kcmd->list, &kppg->kcmds_new_list);
+	mutex_unlock(&kppg->mutex);
+
+	dev_dbg(&psys->adev->dev,
+		"START ppg(%d, 0x%p) kcmd 0x%p, queue %d\n",
+		ipu_fw_psys_pg_get_id(kcmd), kppg, kcmd, queue_id);
+
+	/* Kick l-scheduler thread */
+	atomic_set(&psys->wakeup_count, 1);
+	wake_up_interruptible(&psys->sched_cmd_wq);
+
+	return 0;
+}
+
+static int ipu_psys_kcmd_send_to_ppg(struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_psys_fh *fh = kcmd->fh;
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_ppg *kppg;
+	struct ipu_psys_resource_pool *rpr;
+	unsigned long flags;
+	u8 id;
+	bool resche = true;
+
+	rpr = &psys->resource_pool_running;
+	if (kcmd->state == KCMD_STATE_PPG_START)
+		return ipu_psys_kcmd_send_to_ppg_start(kcmd);
+
+	kppg = ipu_psys_identify_kppg(kcmd);
+	spin_lock_irqsave(&psys->pgs_lock, flags);
+	kcmd->kpg->pg_size = 0;
+	spin_unlock_irqrestore(&psys->pgs_lock, flags);
+	if (!kppg) {
+		dev_err(&psys->adev->dev, "token not match\n");
+		return -EINVAL;
+	}
+
+	kcmd->kpg = kppg->kpg;
+
+	dev_dbg(&psys->adev->dev, "%s ppg(%d, 0x%p) kcmd %p\n",
+		(kcmd->state == KCMD_STATE_PPG_STOP) ?
+		"STOP" : "ENQUEUE",
+		ipu_fw_psys_pg_get_id(kcmd), kppg, kcmd);
+
+	if (kcmd->state == KCMD_STATE_PPG_STOP) {
+		mutex_lock(&kppg->mutex);
+		if (kppg->state == PPG_STATE_STOPPED) {
+			dev_dbg(&psys->adev->dev,
+				"kppg 0x%p  stopped!\n", kppg);
+			id = ipu_fw_psys_ppg_get_base_queue_id(kcmd);
+			ipu_psys_free_cmd_queue_resource(rpr, id);
+			ipu_psys_kcmd_complete(kppg, kcmd, 0);
+			pm_runtime_put(&psys->adev->dev);
+			resche = false;
+		} else {
+			list_add(&kcmd->list, &kppg->kcmds_new_list);
+		}
+		mutex_unlock(&kppg->mutex);
+	} else {
+		int ret;
+
+		ret = ipu_psys_ppg_get_bufset(kcmd, kppg);
+		if (ret)
+			return ret;
+
+		mutex_lock(&kppg->mutex);
+		list_add_tail(&kcmd->list, &kppg->kcmds_new_list);
+		mutex_unlock(&kppg->mutex);
+	}
+
+	if (resche) {
+		/* Kick l-scheduler thread */
+		atomic_set(&psys->wakeup_count, 1);
+		wake_up_interruptible(&psys->sched_cmd_wq);
+	}
+	return 0;
+}
+
+int ipu_psys_kcmd_new(struct ipu_psys_command *cmd, struct ipu_psys_fh *fh)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_kcmd *kcmd;
+	size_t pg_size;
+	int ret;
+
+	if (psys->adev->isp->flr_done)
+		return -EIO;
+
+	kcmd = ipu_psys_copy_cmd(cmd, fh);
+	if (!kcmd)
+		return -EINVAL;
+
+	pg_size = ipu_fw_psys_pg_get_size(kcmd);
+	if (pg_size > kcmd->kpg->pg_size) {
+		dev_dbg(&psys->adev->dev, "pg size mismatch %lu %lu\n",
+			pg_size, kcmd->kpg->pg_size);
+		ret = -EINVAL;
+		goto error;
+	}
+
+	if (ipu_fw_psys_pg_get_protocol(kcmd) !=
+			IPU_FW_PSYS_PROCESS_GROUP_PROTOCOL_PPG) {
+		dev_err(&psys->adev->dev, "No support legacy pg now\n");
+		ret = -EINVAL;
+		goto error;
+	}
+
+	if (cmd->min_psys_freq) {
+		kcmd->constraint.min_freq = cmd->min_psys_freq;
+		ipu_buttress_add_psys_constraint(psys->adev->isp,
+						 &kcmd->constraint);
+	}
+
+	ret = ipu_psys_kcmd_send_to_ppg(kcmd);
+	if (ret)
+		goto error;
+
+	dev_dbg(&psys->adev->dev,
+		"IOC_QCMD: user_token:%llx issue_id:0x%llx pri:%d\n",
+		cmd->user_token, cmd->issue_id, cmd->priority);
+
+	return 0;
+
+error:
+	ipu_psys_kcmd_free(kcmd);
+
+	return ret;
+}
+
+static bool ipu_psys_kcmd_is_valid(struct ipu_psys *psys,
+				   struct ipu_psys_kcmd *kcmd)
+{
+	struct ipu_psys_fh *fh;
+	struct ipu_psys_kcmd *kcmd0;
+	struct ipu_psys_ppg *kppg, *tmp;
+	struct ipu_psys_scheduler *sched;
+
+	list_for_each_entry(fh, &psys->fhs, list) {
+		sched = &fh->sched;
+		mutex_lock(&fh->mutex);
+		if (list_empty(&sched->ppgs)) {
+			mutex_unlock(&fh->mutex);
+			continue;
+		}
+		list_for_each_entry_safe(kppg, tmp, &sched->ppgs, list) {
+			mutex_lock(&kppg->mutex);
+			list_for_each_entry(kcmd0,
+					    &kppg->kcmds_processing_list,
+					    list) {
+				if (kcmd0 == kcmd) {
+					mutex_unlock(&kppg->mutex);
+					mutex_unlock(&fh->mutex);
+					return true;
+				}
+			}
+			mutex_unlock(&kppg->mutex);
+		}
+		mutex_unlock(&fh->mutex);
+	}
+
+	return false;
+}
+
+void ipu_psys_handle_events(struct ipu_psys *psys)
+{
+	struct ipu_psys_kcmd *kcmd;
+	struct ipu_fw_psys_event event;
+	struct ipu_psys_ppg *kppg;
+	bool error;
+	u32 hdl;
+	u16 cmd, status;
+	int res;
+
+	do {
+		memset(&event, 0, sizeof(event));
+		if (!ipu_fw_psys_rcv_event(psys, &event))
+			break;
+
+		if (!event.context_handle)
+			break;
+
+		dev_dbg(&psys->adev->dev, "ppg event: 0x%x, %d, status %d\n",
+			event.context_handle, event.command, event.status);
+
+		error = false;
+		/*
+		 * event.command == CMD_RUN shows this is fw processing frame
+		 * done as pPG mode, and event.context_handle should be pointer
+		 * of buffer set; so we make use of this pointer to lookup
+		 * kbuffer_set and kcmd
+		 */
+		hdl = event.context_handle;
+		cmd = event.command;
+		status = event.status;
+
+		kppg = NULL;
+		kcmd = NULL;
+		if (cmd == IPU_FW_PSYS_PROCESS_GROUP_CMD_RUN) {
+			struct ipu_psys_buffer_set *kbuf_set;
+			/*
+			 * Need change ppg state when the 1st running is done
+			 * (after PPG started/resumed)
+			 */
+			kbuf_set = ipu_psys_lookup_kbuffer_set(psys, hdl);
+			if (kbuf_set)
+				kcmd = kbuf_set->kcmd;
+			if (!kbuf_set || !kcmd)
+				error = true;
+			else
+				kppg = ipu_psys_identify_kppg(kcmd);
+		} else if (cmd == IPU_FW_PSYS_PROCESS_GROUP_CMD_STOP ||
+			   cmd == IPU_FW_PSYS_PROCESS_GROUP_CMD_SUSPEND ||
+			   cmd == IPU_FW_PSYS_PROCESS_GROUP_CMD_RESUME) {
+			/*
+			 * STOP/SUSPEND/RESUME cmd event would run this branch;
+			 * only stop cmd queued by user has stop_kcmd and need
+			 * to notify user to dequeue.
+			 */
+			kppg = ipu_psys_lookup_ppg(psys, hdl);
+			if (kppg) {
+				mutex_lock(&kppg->mutex);
+				if (kppg->state == PPG_STATE_STOPPING) {
+					kcmd = ipu_psys_ppg_get_stop_kcmd(kppg);
+					if (!kcmd)
+						error = true;
+				}
+				mutex_unlock(&kppg->mutex);
+			}
+		} else {
+			dev_err(&psys->adev->dev, "invalid event\n");
+			continue;
+		}
+
+		if (error || !kppg) {
+			dev_err(&psys->adev->dev, "event error, command %d\n",
+				cmd);
+			break;
+		}
+
+		dev_dbg(&psys->adev->dev, "event to kppg 0x%p, kcmd 0x%p\n",
+			kppg, kcmd);
+
+		ipu_psys_ppg_complete(psys, kppg);
+
+		if (kcmd && ipu_psys_kcmd_is_valid(psys, kcmd)) {
+			res = (status == IPU_PSYS_EVENT_CMD_COMPLETE ||
+			       status == IPU_PSYS_EVENT_FRAGMENT_COMPLETE) ?
+				0 : -EIO;
+			mutex_lock(&kppg->mutex);
+			ipu_psys_kcmd_complete(kppg, kcmd, res);
+			mutex_unlock(&kppg->mutex);
+		}
+	} while (1);
+}
+
+int ipu_psys_fh_init(struct ipu_psys_fh *fh)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_buffer_set *kbuf_set, *kbuf_set_tmp;
+	struct ipu_psys_scheduler *sched = &fh->sched;
+	int i;
+
+	mutex_init(&sched->bs_mutex);
+	INIT_LIST_HEAD(&sched->buf_sets);
+	INIT_LIST_HEAD(&sched->ppgs);
+	pm_runtime_dont_use_autosuspend(&psys->adev->dev);
+	/* allocate and map memory for buf_sets */
+	for (i = 0; i < IPU_PSYS_BUF_SET_POOL_SIZE; i++) {
+		kbuf_set = kzalloc(sizeof(*kbuf_set), GFP_KERNEL);
+		if (!kbuf_set)
+			goto out_free_buf_sets;
+		kbuf_set->kaddr = dma_alloc_attrs(&psys->adev->dev,
+						  IPU_PSYS_BUF_SET_MAX_SIZE,
+						  &kbuf_set->dma_addr,
+						  GFP_KERNEL,
+						  0);
+		if (!kbuf_set->kaddr) {
+			kfree(kbuf_set);
+			goto out_free_buf_sets;
+		}
+		kbuf_set->size = IPU_PSYS_BUF_SET_MAX_SIZE;
+		list_add(&kbuf_set->list, &sched->buf_sets);
+	}
+
+	return 0;
+
+out_free_buf_sets:
+	list_for_each_entry_safe(kbuf_set, kbuf_set_tmp,
+				 &sched->buf_sets, list) {
+		dma_free_attrs(&psys->adev->dev,
+			       kbuf_set->size, kbuf_set->kaddr,
+			       kbuf_set->dma_addr, 0);
+		list_del(&kbuf_set->list);
+		kfree(kbuf_set);
+	}
+	mutex_destroy(&sched->bs_mutex);
+
+	return -ENOMEM;
+}
+
+int ipu_psys_fh_deinit(struct ipu_psys_fh *fh)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_ppg *kppg, *kppg0;
+	struct ipu_psys_kcmd *kcmd, *kcmd0;
+	struct ipu_psys_buffer_set *kbuf_set, *kbuf_set0;
+	struct ipu_psys_scheduler *sched = &fh->sched;
+	struct ipu_psys_resource_pool *rpr;
+	struct ipu_psys_resource_alloc *alloc;
+	u8 id;
+
+	mutex_lock(&fh->mutex);
+	if (!list_empty(&sched->ppgs)) {
+		list_for_each_entry_safe(kppg, kppg0, &sched->ppgs, list) {
+			unsigned long flags;
+
+			mutex_lock(&kppg->mutex);
+			if (!(kppg->state &
+			      (PPG_STATE_STOPPED |
+			       PPG_STATE_STOPPING))) {
+				struct ipu_psys_kcmd tmp = {
+					.kpg = kppg->kpg,
+				};
+
+				rpr = &psys->resource_pool_running;
+				alloc = &kppg->kpg->resource_alloc;
+				id = ipu_fw_psys_ppg_get_base_queue_id(&tmp);
+				ipu_psys_ppg_stop(kppg);
+				ipu_psys_free_resources(alloc, rpr);
+				ipu_psys_free_cmd_queue_resource(rpr, id);
+				dev_dbg(&psys->adev->dev,
+				    "s_change:%s %p %d -> %d\n", __func__,
+				    kppg, kppg->state, PPG_STATE_STOPPED);
+				kppg->state = PPG_STATE_STOPPED;
+				if (psys->power_gating != PSYS_POWER_GATED)
+					pm_runtime_put(&psys->adev->dev);
+			}
+			list_del(&kppg->list);
+			mutex_unlock(&kppg->mutex);
+
+			list_for_each_entry_safe(kcmd, kcmd0,
+						 &kppg->kcmds_new_list, list) {
+				kcmd->pg_user = NULL;
+				mutex_unlock(&fh->mutex);
+				ipu_psys_kcmd_free(kcmd);
+				mutex_lock(&fh->mutex);
+			}
+
+			list_for_each_entry_safe(kcmd, kcmd0,
+						 &kppg->kcmds_processing_list,
+						 list) {
+				kcmd->pg_user = NULL;
+				mutex_unlock(&fh->mutex);
+				ipu_psys_kcmd_free(kcmd);
+				mutex_lock(&fh->mutex);
+			}
+
+			list_for_each_entry_safe(kcmd, kcmd0,
+						 &kppg->kcmds_finished_list,
+						 list) {
+				kcmd->pg_user = NULL;
+				mutex_unlock(&fh->mutex);
+				ipu_psys_kcmd_free(kcmd);
+				mutex_lock(&fh->mutex);
+			}
+
+			spin_lock_irqsave(&psys->pgs_lock, flags);
+			kppg->kpg->pg_size = 0;
+			spin_unlock_irqrestore(&psys->pgs_lock, flags);
+
+			mutex_destroy(&kppg->mutex);
+			kfree(kppg->manifest);
+			kfree(kppg);
+		}
+	}
+	mutex_unlock(&fh->mutex);
+
+	mutex_lock(&sched->bs_mutex);
+	list_for_each_entry_safe(kbuf_set, kbuf_set0, &sched->buf_sets, list) {
+		dma_free_attrs(&psys->adev->dev,
+			       kbuf_set->size, kbuf_set->kaddr,
+			       kbuf_set->dma_addr, 0);
+		list_del(&kbuf_set->list);
+		kfree(kbuf_set);
+	}
+	mutex_unlock(&sched->bs_mutex);
+	mutex_destroy(&sched->bs_mutex);
+
+	return 0;
+}
+
+struct ipu_psys_kcmd *ipu_get_completed_kcmd(struct ipu_psys_fh *fh)
+{
+	struct ipu_psys_scheduler *sched = &fh->sched;
+	struct ipu_psys_kcmd *kcmd;
+	struct ipu_psys_ppg *kppg;
+
+	mutex_lock(&fh->mutex);
+	if (list_empty(&sched->ppgs)) {
+		mutex_unlock(&fh->mutex);
+		return NULL;
+	}
+
+	list_for_each_entry(kppg, &sched->ppgs, list) {
+		mutex_lock(&kppg->mutex);
+		if (list_empty(&kppg->kcmds_finished_list)) {
+			mutex_unlock(&kppg->mutex);
+			continue;
+		}
+
+		kcmd = list_first_entry(&kppg->kcmds_finished_list,
+					struct ipu_psys_kcmd, list);
+		mutex_unlock(&fh->mutex);
+		mutex_unlock(&kppg->mutex);
+		dev_dbg(&fh->psys->adev->dev,
+			"get completed kcmd 0x%p\n", kcmd);
+		return kcmd;
+	}
+	mutex_unlock(&fh->mutex);
+
+	return NULL;
+}
+
+long ipu_ioctl_dqevent(struct ipu_psys_event *event,
+		       struct ipu_psys_fh *fh, unsigned int f_flags)
+{
+	struct ipu_psys *psys = fh->psys;
+	struct ipu_psys_kcmd *kcmd = NULL;
+	int rval;
+
+	dev_dbg(&psys->adev->dev, "IOC_DQEVENT\n");
+
+	if (!(f_flags & O_NONBLOCK)) {
+		rval = wait_event_interruptible(fh->wait,
+						(kcmd =
+						 ipu_get_completed_kcmd(fh)));
+		if (rval == -ERESTARTSYS)
+			return rval;
+	}
+
+	if (!kcmd) {
+		kcmd = ipu_get_completed_kcmd(fh);
+		if (!kcmd)
+			return -ENODATA;
+	}
+
+	*event = kcmd->ev;
+	ipu_psys_kcmd_free(kcmd);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6.c
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 - 2021 Intel Corporation
+
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+
+#include "ipu.h"
+#include "ipu-cpd.h"
+#include "ipu-isys.h"
+#include "ipu-psys.h"
+#include "ipu-platform.h"
+#include "ipu-platform-regs.h"
+#include "ipu-platform-buttress-regs.h"
+#include "ipu-platform-isys-csi2-reg.h"
+
+struct ipu_cell_program_t {
+	unsigned int magic_number;
+
+	unsigned int blob_offset;
+	unsigned int blob_size;
+
+	unsigned int start[3];
+
+	unsigned int icache_source;
+	unsigned int icache_target;
+	unsigned int icache_size;
+
+	unsigned int pmem_source;
+	unsigned int pmem_target;
+	unsigned int pmem_size;
+
+	unsigned int data_source;
+	unsigned int data_target;
+	unsigned int data_size;
+
+	unsigned int bss_target;
+	unsigned int bss_size;
+
+	unsigned int cell_id;
+	unsigned int regs_addr;
+
+	unsigned int cell_pmem_data_bus_address;
+	unsigned int cell_dmem_data_bus_address;
+	unsigned int cell_pmem_control_bus_address;
+	unsigned int cell_dmem_control_bus_address;
+
+	unsigned int next;
+	unsigned int dummy[2];
+};
+
+static unsigned int ipu6se_csi_offsets[] = {
+	IPU_CSI_PORT_A_ADDR_OFFSET,
+	IPU_CSI_PORT_B_ADDR_OFFSET,
+	IPU_CSI_PORT_C_ADDR_OFFSET,
+	IPU_CSI_PORT_D_ADDR_OFFSET,
+};
+
+static unsigned int ipu6_csi_offsets[] = {
+	IPU_CSI_PORT_A_ADDR_OFFSET,
+	IPU_CSI_PORT_B_ADDR_OFFSET,
+	IPU_CSI_PORT_C_ADDR_OFFSET,
+	IPU_CSI_PORT_D_ADDR_OFFSET,
+	IPU_CSI_PORT_E_ADDR_OFFSET,
+	IPU_CSI_PORT_F_ADDR_OFFSET,
+	IPU_CSI_PORT_G_ADDR_OFFSET,
+	IPU_CSI_PORT_H_ADDR_OFFSET
+};
+
+struct ipu_isys_internal_pdata isys_ipdata = {
+	.hw_variant = {
+		       .offset = IPU_UNIFIED_OFFSET,
+		       .nr_mmus = 3,
+		       .mmu_hw = {
+				{
+				   .offset = IPU_ISYS_IOMMU0_OFFSET,
+				   .info_bits =
+				   IPU_INFO_REQUEST_DESTINATION_IOSF,
+				   .nr_l1streams = 16,
+				   .l1_block_sz = {
+						   3, 8, 2, 2, 2, 2, 2, 2, 1, 1,
+						   1, 1, 1, 1, 1, 1
+				   },
+				   .nr_l2streams = 16,
+				   .l2_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2
+				   },
+				   .insert_read_before_invalidate = false,
+				   .l1_stream_id_reg_offset =
+				   IPU_MMU_L1_STREAM_ID_REG_OFFSET,
+				   .l2_stream_id_reg_offset =
+				   IPU_MMU_L2_STREAM_ID_REG_OFFSET,
+				},
+				{
+				   .offset = IPU_ISYS_IOMMU1_OFFSET,
+				   .info_bits = IPU_INFO_STREAM_ID_SET(0),
+				   .nr_l1streams = 16,
+				   .l1_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 1, 1, 4
+				   },
+				   .nr_l2streams = 16,
+				   .l2_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2
+				   },
+				   .insert_read_before_invalidate = false,
+				   .l1_stream_id_reg_offset =
+				   IPU_MMU_L1_STREAM_ID_REG_OFFSET,
+				   .l2_stream_id_reg_offset =
+				   IPU_MMU_L2_STREAM_ID_REG_OFFSET,
+				},
+				{
+				   .offset = IPU_ISYS_IOMMUI_OFFSET,
+				   .info_bits = IPU_INFO_STREAM_ID_SET(0),
+				   .nr_l1streams = 0,
+				   .nr_l2streams = 0,
+				   .insert_read_before_invalidate = false,
+				},
+			},
+		       .cdc_fifos = 3,
+		       .cdc_fifo_threshold = {6, 8, 2},
+		       .dmem_offset = IPU_ISYS_DMEM_OFFSET,
+		       .spc_offset = IPU_ISYS_SPC_OFFSET,
+	},
+	.isys_dma_overshoot = IPU_ISYS_OVERALLOC_MIN,
+};
+
+struct ipu_psys_internal_pdata psys_ipdata = {
+	.hw_variant = {
+		       .offset = IPU_UNIFIED_OFFSET,
+		       .nr_mmus = 4,
+		       .mmu_hw = {
+				{
+				   .offset = IPU_PSYS_IOMMU0_OFFSET,
+				   .info_bits =
+				   IPU_INFO_REQUEST_DESTINATION_IOSF,
+				   .nr_l1streams = 16,
+				   .l1_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2
+				   },
+				   .nr_l2streams = 16,
+				   .l2_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2
+				   },
+				   .insert_read_before_invalidate = false,
+				   .l1_stream_id_reg_offset =
+				   IPU_MMU_L1_STREAM_ID_REG_OFFSET,
+				   .l2_stream_id_reg_offset =
+				   IPU_MMU_L2_STREAM_ID_REG_OFFSET,
+				},
+				{
+				   .offset = IPU_PSYS_IOMMU1_OFFSET,
+				   .info_bits = IPU_INFO_STREAM_ID_SET(0),
+				   .nr_l1streams = 32,
+				   .l1_block_sz = {
+						   1, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 10,
+						   5, 4, 14, 6, 4, 14, 6, 4, 8,
+						   4, 2, 1, 1, 1, 1, 14
+				   },
+				   .nr_l2streams = 32,
+				   .l2_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2
+				   },
+				   .insert_read_before_invalidate = false,
+				   .l1_stream_id_reg_offset =
+				   IPU_MMU_L1_STREAM_ID_REG_OFFSET,
+				   .l2_stream_id_reg_offset =
+				   IPU_PSYS_MMU1W_L2_STREAM_ID_REG_OFFSET,
+				},
+				{
+				   .offset = IPU_PSYS_IOMMU1R_OFFSET,
+				   .info_bits = IPU_INFO_STREAM_ID_SET(0),
+				   .nr_l1streams = 16,
+				   .l1_block_sz = {
+						   1, 4, 4, 4, 4, 16, 8, 4, 32,
+						   16, 16, 2, 2, 2, 1, 12
+				   },
+				   .nr_l2streams = 16,
+				   .l2_block_sz = {
+						   2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+						   2, 2, 2, 2, 2, 2
+				   },
+				   .insert_read_before_invalidate = false,
+				   .l1_stream_id_reg_offset =
+				   IPU_MMU_L1_STREAM_ID_REG_OFFSET,
+				   .l2_stream_id_reg_offset =
+				   IPU_MMU_L2_STREAM_ID_REG_OFFSET,
+				},
+				{
+				   .offset = IPU_PSYS_IOMMUI_OFFSET,
+				   .info_bits = IPU_INFO_STREAM_ID_SET(0),
+				   .nr_l1streams = 0,
+				   .nr_l2streams = 0,
+				   .insert_read_before_invalidate = false,
+				},
+		},
+	       .dmem_offset = IPU_PSYS_DMEM_OFFSET,
+	},
+};
+
+const struct ipu_buttress_ctrl isys_buttress_ctrl = {
+	.ratio = IPU_IS_FREQ_CTL_DEFAULT_RATIO,
+	.qos_floor = IPU_IS_FREQ_CTL_DEFAULT_QOS_FLOOR_RATIO,
+	.freq_ctl = IPU_BUTTRESS_REG_IS_FREQ_CTL,
+	.pwr_sts_shift = IPU_BUTTRESS_PWR_STATE_IS_PWR_SHIFT,
+	.pwr_sts_mask = IPU_BUTTRESS_PWR_STATE_IS_PWR_MASK,
+	.pwr_sts_on = IPU_BUTTRESS_PWR_STATE_UP_DONE,
+	.pwr_sts_off = IPU_BUTTRESS_PWR_STATE_DN_DONE,
+};
+
+const struct ipu_buttress_ctrl psys_buttress_ctrl = {
+	.ratio = IPU_PS_FREQ_CTL_DEFAULT_RATIO,
+	.qos_floor = IPU_PS_FREQ_CTL_DEFAULT_QOS_FLOOR_RATIO,
+	.freq_ctl = IPU_BUTTRESS_REG_PS_FREQ_CTL,
+	.pwr_sts_shift = IPU_BUTTRESS_PWR_STATE_PS_PWR_SHIFT,
+	.pwr_sts_mask = IPU_BUTTRESS_PWR_STATE_PS_PWR_MASK,
+	.pwr_sts_on = IPU_BUTTRESS_PWR_STATE_UP_DONE,
+	.pwr_sts_off = IPU_BUTTRESS_PWR_STATE_DN_DONE,
+};
+
+static void ipu6_pkg_dir_configure_spc(struct ipu_device *isp,
+				       const struct ipu_hw_variants *hw_variant,
+				       int pkg_dir_idx, void __iomem *base,
+				       u64 *pkg_dir,
+				       dma_addr_t pkg_dir_vied_address)
+{
+	struct ipu_psys *psys = ipu_bus_get_drvdata(isp->psys);
+	struct ipu_isys *isys = ipu_bus_get_drvdata(isp->isys);
+	unsigned int server_fw_virtaddr;
+	struct ipu_cell_program_t *prog;
+	void __iomem *spc_base;
+	dma_addr_t dma_addr;
+
+	if (!pkg_dir || !isp->cpd_fw) {
+		dev_err(&isp->pdev->dev, "invalid addr\n");
+		return;
+	}
+
+	server_fw_virtaddr = *(pkg_dir + (pkg_dir_idx + 1) * 2);
+	if (pkg_dir_idx == IPU_CPD_PKG_DIR_ISYS_SERVER_IDX) {
+		dma_addr = sg_dma_address(isys->fw_sgt.sgl);
+		prog = (struct ipu_cell_program_t *)((u64)isp->cpd_fw->data +
+							(server_fw_virtaddr -
+							 dma_addr));
+	} else {
+		dma_addr = sg_dma_address(psys->fw_sgt.sgl);
+		prog = (struct ipu_cell_program_t *)((u64)isp->cpd_fw->data +
+							(server_fw_virtaddr -
+							 dma_addr));
+	}
+
+	spc_base = base + prog->regs_addr;
+	if (spc_base != (base + hw_variant->spc_offset))
+		dev_warn(&isp->pdev->dev,
+			 "SPC reg addr 0x%p not matching value from CPD 0x%p\n",
+			 base + hw_variant->spc_offset, spc_base);
+	writel(server_fw_virtaddr + prog->blob_offset +
+	       prog->icache_source, spc_base + IPU_PSYS_REG_SPC_ICACHE_BASE);
+	writel(IPU_INFO_REQUEST_DESTINATION_IOSF,
+	       spc_base + IPU_REG_PSYS_INFO_SEG_0_CONFIG_ICACHE_MASTER);
+	writel(prog->start[1], spc_base + IPU_PSYS_REG_SPC_START_PC);
+	writel(pkg_dir_vied_address, base + hw_variant->dmem_offset);
+}
+
+void ipu_configure_spc(struct ipu_device *isp,
+		       const struct ipu_hw_variants *hw_variant,
+		       int pkg_dir_idx, void __iomem *base, u64 *pkg_dir,
+		       dma_addr_t pkg_dir_dma_addr)
+{
+	u32 val;
+	void __iomem *dmem_base = base + hw_variant->dmem_offset;
+	void __iomem *spc_regs_base = base + hw_variant->spc_offset;
+
+	val = readl(spc_regs_base + IPU_PSYS_REG_SPC_STATUS_CTRL);
+	val |= IPU_PSYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE;
+	writel(val, spc_regs_base + IPU_PSYS_REG_SPC_STATUS_CTRL);
+
+	if (isp->secure_mode)
+		writel(IPU_PKG_DIR_IMR_OFFSET, dmem_base);
+	else
+		ipu6_pkg_dir_configure_spc(isp, hw_variant, pkg_dir_idx, base,
+					   pkg_dir, pkg_dir_dma_addr);
+}
+EXPORT_SYMBOL(ipu_configure_spc);
+
+int ipu_buttress_psys_freq_get(void *data, u64 *val)
+{
+	struct ipu_device *isp = data;
+	u32 reg_val;
+	int rval;
+
+	rval = pm_runtime_get_sync(&isp->psys->dev);
+	if (rval < 0) {
+		pm_runtime_put(&isp->psys->dev);
+		dev_err(&isp->pdev->dev, "Runtime PM failed (%d)\n", rval);
+		return rval;
+	}
+
+	reg_val = readl(isp->base + BUTTRESS_REG_PS_FREQ_CTL);
+
+	pm_runtime_put(&isp->psys->dev);
+
+	*val = IPU_PS_FREQ_RATIO_BASE *
+	    (reg_val & IPU_BUTTRESS_PS_FREQ_CTL_DIVISOR_MASK);
+
+	return 0;
+}
+
+void ipu_internal_pdata_init(void)
+{
+	if (ipu_ver == IPU_VER_6 || ipu_ver == IPU_VER_6EP) {
+		isys_ipdata.csi2.nports = ARRAY_SIZE(ipu6_csi_offsets);
+		isys_ipdata.csi2.offsets = ipu6_csi_offsets;
+		isys_ipdata.num_parallel_streams = IPU6_ISYS_NUM_STREAMS;
+		psys_ipdata.hw_variant.spc_offset = IPU6_PSYS_SPC_OFFSET;
+
+	} else if (ipu_ver == IPU_VER_6SE) {
+		isys_ipdata.csi2.nports = ARRAY_SIZE(ipu6se_csi_offsets);
+		isys_ipdata.csi2.offsets = ipu6se_csi_offsets;
+		isys_ipdata.num_parallel_streams = IPU6SE_ISYS_NUM_STREAMS;
+		psys_ipdata.hw_variant.spc_offset = IPU6SE_PSYS_SPC_OFFSET;
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6ep-fw-resources.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6ep-fw-resources.c
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 Intel Corporation
+
+#include <linux/err.h>
+#include <linux/string.h>
+
+#include "ipu-psys.h"
+#include "ipu-fw-psys.h"
+#include "ipu6-platform-resources.h"
+#include "ipu6ep-platform-resources.h"
+
+/* resources table */
+
+/*
+ * Cell types by cell IDs
+ */
+static const u8 ipu6ep_fw_psys_cell_types[IPU6EP_FW_PSYS_N_CELL_ID] = {
+	IPU6_FW_PSYS_SP_CTRL_TYPE_ID,
+	IPU6_FW_PSYS_VP_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_OSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_PSA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* AF */
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* X2B_MD */
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* X2B_SVE_RGBIR */
+	IPU6_FW_PSYS_ACC_ISA_TYPE_ID, /* PAF */
+	IPU6_FW_PSYS_GDC_TYPE_ID,
+	IPU6_FW_PSYS_TNR_TYPE_ID,
+};
+
+static const u16 ipu6ep_fw_num_dev_channels[IPU6_FW_PSYS_N_DEV_CHN_ID] = {
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT0_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_READ_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_INTERNAL_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_CHN_DMA_ISA_MAX_SIZE,
+};
+
+static const u16 ipu6ep_fw_psys_mem_size[IPU6_FW_PSYS_N_MEM_ID] = {
+	IPU6_FW_PSYS_VMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_TRANSFER_VMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_TRANSFER_VMEM1_MAX_SIZE,
+	IPU6_FW_PSYS_LB_VMEM_MAX_SIZE,
+	IPU6_FW_PSYS_BAMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM0_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM1_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM2_MAX_SIZE,
+	IPU6_FW_PSYS_DMEM3_MAX_SIZE,
+	IPU6_FW_PSYS_PMEM0_MAX_SIZE
+};
+
+static const u16 ipu6ep_fw_psys_dfms[IPU6_FW_PSYS_N_DEV_DFM_ID] = {
+	IPU6_FW_PSYS_DEV_DFM_BB_FULL_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_BB_EMPTY_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_LB_FULL_PORT_ID_MAX_SIZE,
+	IPU6_FW_PSYS_DEV_DFM_LB_EMPTY_PORT_ID_MAX_SIZE,
+};
+
+static const u8
+ipu6ep_fw_psys_c_mem[IPU6EP_FW_PSYS_N_CELL_ID][IPU6_FW_PSYS_N_MEM_TYPE_ID] = {
+	{
+		/* IPU6_FW_PSYS_SP0_ID */
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_DMEM0_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_SP1_ID */
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_DMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_VP0_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_DMEM3_ID,
+		IPU6_FW_PSYS_VMEM0_ID,
+		IPU6_FW_PSYS_BAMEM0_ID,
+		IPU6_FW_PSYS_PMEM0_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC1_ID BNLM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC2_ID DM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC3_ID ACM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC4_ID GTC YUV1 */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC5_ID OFS pin main */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC6_ID OFS pin display */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC7_ID OFS pin pp */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC8_ID GAMMASTAR */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC9_ID GLTM */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ACC10_ID XNR */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_ICA_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_LSC_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_DPC_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_SIS_A_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_SIS_B_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_B2B_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_B2R_ID and ISA_R2I_SIE */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_R2I_DS_A_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_AWB_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_AE_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_AF_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_X2B_MD_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_X2B_SVE_RGBIR_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_ISA_PAF_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_LB_VMEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_BB_ACC_GDC0_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	},
+	{
+		/* IPU6_FW_PSYS_BB_ACC_TNR_ID */
+		IPU6_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6_FW_PSYS_TRANSFER_VMEM1_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+		IPU6_FW_PSYS_N_MEM_ID,
+	}
+};
+
+static const struct ipu_fw_resource_definitions ipu6ep_defs = {
+	.cells = ipu6ep_fw_psys_cell_types,
+	.num_cells = IPU6EP_FW_PSYS_N_CELL_ID,
+	.num_cells_type = IPU6_FW_PSYS_N_CELL_TYPE_ID,
+
+	.dev_channels = ipu6ep_fw_num_dev_channels,
+	.num_dev_channels = IPU6_FW_PSYS_N_DEV_CHN_ID,
+
+	.num_ext_mem_types = IPU6_FW_PSYS_N_DATA_MEM_TYPE_ID,
+	.num_ext_mem_ids = IPU6_FW_PSYS_N_MEM_ID,
+	.ext_mem_ids = ipu6ep_fw_psys_mem_size,
+
+	.num_dfm_ids = IPU6_FW_PSYS_N_DEV_DFM_ID,
+
+	.dfms = ipu6ep_fw_psys_dfms,
+
+	.cell_mem_row = IPU6_FW_PSYS_N_MEM_TYPE_ID,
+	.cell_mem = &ipu6ep_fw_psys_c_mem[0][0],
+};
+
+const struct ipu_fw_resource_definitions *ipu6ep_res_defs = &ipu6ep_defs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6ep-platform-resources.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6ep-platform-resources.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Intel Corporation */
+
+#ifndef IPU6EP_PLATFORM_RESOURCES_H
+#define IPU6EP_PLATFORM_RESOURCES_H
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+
+enum {
+	IPU6EP_FW_PSYS_SP0_ID = 0,
+	IPU6EP_FW_PSYS_VP0_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_BNLM_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_DM_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_ACM_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_GTC_YUV1_ID,
+	IPU6EP_FW_PSYS_BB_ACC_OFS_PIN_MAIN_ID,
+	IPU6EP_FW_PSYS_BB_ACC_OFS_PIN_DISPLAY_ID,
+	IPU6EP_FW_PSYS_BB_ACC_OFS_PIN_PP_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_GAMMASTAR_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_GLTM_ID,
+	IPU6EP_FW_PSYS_PSA_ACC_XNR_ID,
+	IPU6EP_FW_PSYS_PSA_VCSC_ID,	/* VCSC */
+	IPU6EP_FW_PSYS_ISA_ICA_ID,
+	IPU6EP_FW_PSYS_ISA_LSC_ID,
+	IPU6EP_FW_PSYS_ISA_DPC_ID,
+	IPU6EP_FW_PSYS_ISA_SIS_A_ID,
+	IPU6EP_FW_PSYS_ISA_SIS_B_ID,
+	IPU6EP_FW_PSYS_ISA_B2B_ID,
+	IPU6EP_FW_PSYS_ISA_B2R_R2I_SIE_ID,
+	IPU6EP_FW_PSYS_ISA_R2I_DS_A_ID,
+	IPU6EP_FW_PSYS_ISA_AWB_ID,
+	IPU6EP_FW_PSYS_ISA_AE_ID,
+	IPU6EP_FW_PSYS_ISA_AF_ID,
+	IPU6EP_FW_PSYS_ISA_X2B_MD_ID,
+	IPU6EP_FW_PSYS_ISA_X2B_SVE_RGBIR_ID,
+	IPU6EP_FW_PSYS_ISA_PAF_ID,
+	IPU6EP_FW_PSYS_BB_ACC_GDC0_ID,
+	IPU6EP_FW_PSYS_BB_ACC_TNR_ID,
+	IPU6EP_FW_PSYS_N_CELL_ID
+};
+#endif /* IPU6EP_PLATFORM_RESOURCES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6se-fw-resources.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6se-fw-resources.c
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2015 - 2019 Intel Corporation
+
+#include <linux/err.h>
+#include <linux/string.h>
+
+#include "ipu-psys.h"
+#include "ipu-fw-psys.h"
+#include "ipu6se-platform-resources.h"
+
+/* resources table */
+
+/*
+ * Cell types by cell IDs
+ */
+/* resources table */
+
+/*
+ * Cell types by cell IDs
+ */
+const u8 ipu6se_fw_psys_cell_types[IPU6SE_FW_PSYS_N_CELL_ID] = {
+	IPU6SE_FW_PSYS_SP_CTRL_TYPE_ID,
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_ICA_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_LSC_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_DPC_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_B2B_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_BNLM_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_DM_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_R2I_SIE_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_R2I_DS_A_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_R2I_DS_B_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_AWB_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_AE_ID */
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID, /* IPU6SE_FW_PSYS_ISA_AF_ID*/
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID  /* PAF */
+};
+
+const u16 ipu6se_fw_num_dev_channels[IPU6SE_FW_PSYS_N_DEV_CHN_ID] = {
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT0_MAX_SIZE,
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT1_READ_MAX_SIZE,
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_MAX_SIZE,
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_ISA_MAX_SIZE,
+};
+
+const u16 ipu6se_fw_psys_mem_size[IPU6SE_FW_PSYS_N_MEM_ID] = {
+	IPU6SE_FW_PSYS_TRANSFER_VMEM0_MAX_SIZE,
+	IPU6SE_FW_PSYS_LB_VMEM_MAX_SIZE,
+	IPU6SE_FW_PSYS_DMEM0_MAX_SIZE,
+	IPU6SE_FW_PSYS_DMEM1_MAX_SIZE
+};
+
+const u16 ipu6se_fw_psys_dfms[IPU6SE_FW_PSYS_N_DEV_DFM_ID] = {
+	IPU6SE_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID_MAX_SIZE,
+	IPU6SE_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID_MAX_SIZE
+};
+
+const u8
+ipu6se_fw_psys_c_mem[IPU6SE_FW_PSYS_N_CELL_ID][IPU6SE_FW_PSYS_N_MEM_TYPE_ID] = {
+	{ /* IPU6SE_FW_PSYS_SP0_ID */
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_DMEM0_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_ICA_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_LSC_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_DPC_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_B2B_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+
+	{ /* IPU6SE_FW_PSYS_ISA_BNLM_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_DM_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_R2I_SIE_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_R2I_DS_A_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_R2I_DS_B_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_AWB_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_AE_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_AF_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	},
+	{ /* IPU6SE_FW_PSYS_ISA_PAF_ID */
+		IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID,
+		IPU6SE_FW_PSYS_LB_VMEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+		IPU6SE_FW_PSYS_N_MEM_ID,
+	}
+};
+
+static const struct ipu_fw_resource_definitions ipu6se_defs = {
+	.cells = ipu6se_fw_psys_cell_types,
+	.num_cells = IPU6SE_FW_PSYS_N_CELL_ID,
+	.num_cells_type = IPU6SE_FW_PSYS_N_CELL_TYPE_ID,
+
+	.dev_channels = ipu6se_fw_num_dev_channels,
+	.num_dev_channels = IPU6SE_FW_PSYS_N_DEV_CHN_ID,
+
+	.num_ext_mem_types = IPU6SE_FW_PSYS_N_DATA_MEM_TYPE_ID,
+	.num_ext_mem_ids = IPU6SE_FW_PSYS_N_MEM_ID,
+	.ext_mem_ids = ipu6se_fw_psys_mem_size,
+
+	.num_dfm_ids = IPU6SE_FW_PSYS_N_DEV_DFM_ID,
+
+	.dfms = ipu6se_fw_psys_dfms,
+
+	.cell_mem_row = IPU6SE_FW_PSYS_N_MEM_TYPE_ID,
+	.cell_mem = &ipu6se_fw_psys_c_mem[0][0],
+};
+
+const struct ipu_fw_resource_definitions *ipu6se_res_defs = &ipu6se_defs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/intel/ipu6/ipu6se-platform-resources.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/intel/ipu6/ipu6se-platform-resources.h
@@ -0,0 +1,103 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 - 2020 Intel Corporation */
+
+#ifndef IPU6SE_PLATFORM_RESOURCES_H
+#define IPU6SE_PLATFORM_RESOURCES_H
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include "ipu-platform-resources.h"
+
+#define	IPU6SE_FW_PSYS_N_PADDING_UINT8_IN_PROCESS_EXT_STRUCT		1
+
+enum {
+	IPU6SE_FW_PSYS_CMD_QUEUE_COMMAND_ID = 0,
+	IPU6SE_FW_PSYS_CMD_QUEUE_DEVICE_ID,
+	IPU6SE_FW_PSYS_CMD_QUEUE_PPG0_COMMAND_ID,
+	IPU6SE_FW_PSYS_CMD_QUEUE_PPG1_COMMAND_ID,
+	IPU6SE_FW_PSYS_CMD_QUEUE_PPG2_COMMAND_ID,
+	IPU6SE_FW_PSYS_CMD_QUEUE_PPG3_COMMAND_ID,
+	IPU6SE_FW_PSYS_CMD_QUEUE_PPG4_COMMAND_ID,
+	IPU6SE_FW_PSYS_CMD_QUEUE_PPG5_COMMAND_ID,
+	IPU6SE_FW_PSYS_N_PSYS_CMD_QUEUE_ID
+};
+
+enum {
+	IPU6SE_FW_PSYS_TRANSFER_VMEM0_TYPE_ID = 0,
+	IPU6SE_FW_PSYS_LB_VMEM_TYPE_ID,
+	IPU6SE_FW_PSYS_DMEM_TYPE_ID,
+	IPU6SE_FW_PSYS_VMEM_TYPE_ID,
+	IPU6SE_FW_PSYS_BAMEM_TYPE_ID,
+	IPU6SE_FW_PSYS_PMEM_TYPE_ID,
+	IPU6SE_FW_PSYS_N_MEM_TYPE_ID
+};
+
+enum ipu6se_mem_id {
+	IPU6SE_FW_PSYS_TRANSFER_VMEM0_ID = 0,	/* TRANSFER VMEM 0 */
+	IPU6SE_FW_PSYS_LB_VMEM_ID,	/* LB VMEM */
+	IPU6SE_FW_PSYS_DMEM0_ID,	/* SPC0 Dmem */
+	IPU6SE_FW_PSYS_DMEM1_ID,	/* SPP0 Dmem */
+	IPU6SE_FW_PSYS_N_MEM_ID
+};
+
+enum {
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT0_ID = 0,
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT1_READ_ID,
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_ID,
+	IPU6SE_FW_PSYS_DEV_CHN_DMA_ISA_ID,
+	IPU6SE_FW_PSYS_N_DEV_CHN_ID
+};
+
+enum {
+	IPU6SE_FW_PSYS_SP_CTRL_TYPE_ID = 0,
+	IPU6SE_FW_PSYS_SP_SERVER_TYPE_ID,
+	IPU6SE_FW_PSYS_ACC_ISA_TYPE_ID,
+	IPU6SE_FW_PSYS_N_CELL_TYPE_ID
+};
+
+enum {
+	IPU6SE_FW_PSYS_SP0_ID = 0,
+	IPU6SE_FW_PSYS_ISA_ICA_ID,
+	IPU6SE_FW_PSYS_ISA_LSC_ID,
+	IPU6SE_FW_PSYS_ISA_DPC_ID,
+	IPU6SE_FW_PSYS_ISA_B2B_ID,
+	IPU6SE_FW_PSYS_ISA_BNLM_ID,
+	IPU6SE_FW_PSYS_ISA_DM_ID,
+	IPU6SE_FW_PSYS_ISA_R2I_SIE_ID,
+	IPU6SE_FW_PSYS_ISA_R2I_DS_A_ID,
+	IPU6SE_FW_PSYS_ISA_R2I_DS_B_ID,
+	IPU6SE_FW_PSYS_ISA_AWB_ID,
+	IPU6SE_FW_PSYS_ISA_AE_ID,
+	IPU6SE_FW_PSYS_ISA_AF_ID,
+	IPU6SE_FW_PSYS_ISA_PAF_ID,
+	IPU6SE_FW_PSYS_N_CELL_ID
+};
+
+enum {
+	IPU6SE_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID = 0,
+	IPU6SE_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID,
+};
+
+/* Excluding PMEM */
+#define IPU6SE_FW_PSYS_N_DATA_MEM_TYPE_ID (IPU6SE_FW_PSYS_N_MEM_TYPE_ID - 1)
+#define IPU6SE_FW_PSYS_N_DEV_DFM_ID	\
+	(IPU6SE_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID + 1)
+#define IPU6SE_FW_PSYS_VMEM0_MAX_SIZE		0x0800
+/* Transfer VMEM0 words, ref HAS Transfer*/
+#define IPU6SE_FW_PSYS_TRANSFER_VMEM0_MAX_SIZE	0x0800
+#define IPU6SE_FW_PSYS_LB_VMEM_MAX_SIZE		0x0400	/* LB VMEM words */
+#define IPU6SE_FW_PSYS_DMEM0_MAX_SIZE		0x4000
+#define IPU6SE_FW_PSYS_DMEM1_MAX_SIZE		0x1000
+
+#define IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT0_MAX_SIZE		22
+#define IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT1_READ_MAX_SIZE	22
+#define IPU6SE_FW_PSYS_DEV_CHN_DMA_EXT1_WRITE_MAX_SIZE	22
+#define IPU6SE_FW_PSYS_DEV_CHN_DMA_IPFD_MAX_SIZE		0
+#define IPU6SE_FW_PSYS_DEV_CHN_DMA_ISA_MAX_SIZE		2
+
+#define IPU6SE_FW_PSYS_DEV_DFM_ISL_FULL_PORT_ID_MAX_SIZE		32
+#define IPU6SE_FW_PSYS_DEV_DFM_LB_FULL_PORT_ID_MAX_SIZE		32
+#define IPU6SE_FW_PSYS_DEV_DFM_ISL_EMPTY_PORT_ID_MAX_SIZE		32
+#define IPU6SE_FW_PSYS_DEV_DFM_LB_EMPTY_PORT_ID_MAX_SIZE		32
+
+#endif /* IPU6SE_PLATFORM_RESOURCES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ivtv/ivtv-driver.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ivtv/ivtv-driver.h
@@ -330,7 +330,6 @@
 	struct ivtv *itv;		/* for ease of use */
 	const char *name;		/* name of the stream */
 	int type;			/* stream type */
-	u32 caps;			/* V4L2 capabilities */
 
 	struct v4l2_fh *fh;		/* pointer to the streaming filehandle */
 	spinlock_t qlock;		/* locks access to the queues */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ivtv/ivtv-ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ivtv/ivtv-ioctl.c
@@ -438,7 +438,7 @@
 	struct ivtv_stream *s = &itv->streams[fh2id(fh)->type];
 	struct v4l2_window *winfmt = &fmt->fmt.win;
 
-	if (!(s->caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
+	if (!(s->vdev.device_caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
 		return -EINVAL;
 	if (!itv->osd_video_pbase)
 		return -EINVAL;
@@ -549,7 +549,7 @@
 	u32 chromakey = fmt->fmt.win.chromakey;
 	u8 global_alpha = fmt->fmt.win.global_alpha;
 
-	if (!(s->caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
+	if (!(s->vdev.device_caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
 		return -EINVAL;
 	if (!itv->osd_video_pbase)
 		return -EINVAL;
@@ -1383,7 +1383,7 @@
 		0,
 	};
 
-	if (!(s->caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
+	if (!(s->vdev.device_caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
 		return -ENOTTY;
 	if (!itv->osd_video_pbase)
 		return -ENOTTY;
@@ -1450,7 +1450,7 @@
 	struct ivtv_stream *s = &itv->streams[fh2id(fh)->type];
 	struct yuv_playback_info *yi = &itv->yuv_info;
 
-	if (!(s->caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
+	if (!(s->vdev.device_caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
 		return -ENOTTY;
 	if (!itv->osd_video_pbase)
 		return -ENOTTY;
@@ -1470,7 +1470,7 @@
 	struct ivtv *itv = id->itv;
 	struct ivtv_stream *s = &itv->streams[fh2id(fh)->type];
 
-	if (!(s->caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
+	if (!(s->vdev.device_caps & V4L2_CAP_VIDEO_OUTPUT_OVERLAY))
 		return -ENOTTY;
 	if (!itv->osd_video_pbase)
 		return -ENOTTY;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ivtv/ivtv-streams.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ivtv/ivtv-streams.c
@@ -176,7 +176,7 @@
 	s->itv = itv;
 	s->type = type;
 	s->name = ivtv_stream_info[type].name;
-	s->caps = ivtv_stream_info[type].v4l2_caps;
+	s->vdev.device_caps = ivtv_stream_info[type].v4l2_caps;
 
 	if (ivtv_stream_info[type].pio)
 		s->dma = PCI_DMA_NONE;
@@ -299,12 +299,9 @@
 		if (s_mpg->vdev.v4l2_dev)
 			num = s_mpg->vdev.num + ivtv_stream_info[type].num_offset;
 	}
-	s->vdev.device_caps = s->caps;
-	if (itv->osd_video_pbase) {
-		itv->streams[IVTV_DEC_STREAM_TYPE_YUV].vdev.device_caps |=
-			V4L2_CAP_VIDEO_OUTPUT_OVERLAY;
-		itv->streams[IVTV_DEC_STREAM_TYPE_MPG].vdev.device_caps |=
-			V4L2_CAP_VIDEO_OUTPUT_OVERLAY;
+	if (itv->osd_video_pbase && (type == IVTV_DEC_STREAM_TYPE_YUV ||
+				     type == IVTV_DEC_STREAM_TYPE_MPG)) {
+		s->vdev.device_caps |= V4L2_CAP_VIDEO_OUTPUT_OVERLAY;
 		itv->v4l2_cap |= V4L2_CAP_VIDEO_OUTPUT_OVERLAY;
 	}
 	video_set_drvdata(&s->vdev, s);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ivtv/ivtvfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ivtv/ivtvfb.c
@@ -36,7 +36,7 @@
 #include <linux/fb.h>
 #include <linux/ivtvfb.h>
 
-#ifdef CONFIG_X86_64
+#if defined(CONFIG_X86_64) && !defined(CONFIG_UML)
 #include <asm/memtype.h>
 #endif
 
@@ -1157,7 +1157,7 @@
 {
 	int rc;
 
-#ifdef CONFIG_X86_64
+#if defined(CONFIG_X86_64) && !defined(CONFIG_UML)
 	if (pat_enabled()) {
 		if (ivtvfb_force_pat) {
 			pr_info("PAT is enabled. Write-combined framebuffer caching will be disabled.\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/netup_unidvb/netup_unidvb_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/netup_unidvb/netup_unidvb_core.c
@@ -258,19 +258,24 @@
 	if ((reg40 & AVL_IRQ_ASSERTED) != 0) {
 		/* IRQ is being signaled */
 		reg_isr = readw(ndev->bmmio0 + REG_ISR);
-		if (reg_isr & NETUP_UNIDVB_IRQ_I2C0) {
-			iret = netup_i2c_interrupt(&ndev->i2c[0]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_I2C1) {
-			iret = netup_i2c_interrupt(&ndev->i2c[1]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_SPI) {
+		if (reg_isr & NETUP_UNIDVB_IRQ_SPI)
 			iret = netup_spi_interrupt(ndev->spi);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA1) {
-			iret = netup_dma_interrupt(&ndev->dma[0]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA2) {
-			iret = netup_dma_interrupt(&ndev->dma[1]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_CI) {
-			iret = netup_ci_interrupt(ndev);
+		else if (!ndev->old_fw) {
+			if (reg_isr & NETUP_UNIDVB_IRQ_I2C0) {
+				iret = netup_i2c_interrupt(&ndev->i2c[0]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_I2C1) {
+				iret = netup_i2c_interrupt(&ndev->i2c[1]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA1) {
+				iret = netup_dma_interrupt(&ndev->dma[0]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA2) {
+				iret = netup_dma_interrupt(&ndev->dma[1]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_CI) {
+				iret = netup_ci_interrupt(ndev);
+			} else {
+				goto err;
+			}
 		} else {
+err:
 			dev_err(&pci_dev->dev,
 				"%s(): unknown interrupt 0x%x\n",
 				__func__, reg_isr);
@@ -692,7 +697,7 @@
 	netup_unidvb_dma_enable(dma, 0);
 	msleep(50);
 	cancel_work_sync(&dma->work);
-	del_timer(&dma->timeout);
+	del_timer_sync(&dma->timeout);
 }
 
 static int netup_unidvb_dma_setup(struct netup_unidvb_dev *ndev)
@@ -882,12 +887,7 @@
 		ndev->lmmio0, (u32)pci_resource_len(pci_dev, 0),
 		ndev->lmmio1, (u32)pci_resource_len(pci_dev, 1),
 		pci_dev->irq);
-	if (request_irq(pci_dev->irq, netup_unidvb_isr, IRQF_SHARED,
-			"netup_unidvb", pci_dev) < 0) {
-		dev_err(&pci_dev->dev,
-			"%s(): can't get IRQ %d\n", __func__, pci_dev->irq);
-		goto irq_request_err;
-	}
+
 	ndev->dma_size = 2 * 188 *
 		NETUP_DMA_BLOCKS_COUNT * NETUP_DMA_PACKETS_COUNT;
 	ndev->dma_virt = dma_alloc_coherent(&pci_dev->dev,
@@ -928,6 +928,14 @@
 		dev_err(&pci_dev->dev, "netup_unidvb: DMA setup failed\n");
 		goto dma_setup_err;
 	}
+
+	if (request_irq(pci_dev->irq, netup_unidvb_isr, IRQF_SHARED,
+			"netup_unidvb", pci_dev) < 0) {
+		dev_err(&pci_dev->dev,
+			"%s(): can't get IRQ %d\n", __func__, pci_dev->irq);
+		goto dma_setup_err;
+	}
+
 	dev_info(&pci_dev->dev,
 		"netup_unidvb: device has been initialized\n");
 	return 0;
@@ -946,8 +954,6 @@
 	dma_free_coherent(&pci_dev->dev, ndev->dma_size,
 			ndev->dma_virt, ndev->dma_phys);
 dma_alloc_err:
-	free_irq(pci_dev->irq, pci_dev);
-irq_request_err:
 	iounmap(ndev->lmmio1);
 pci_bar1_error:
 	iounmap(ndev->lmmio0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ngene/ngene-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ngene/ngene-core.c
@@ -1488,7 +1488,9 @@
 	}
 
 	if (dev->ci.en && (io & NGENE_IO_TSOUT)) {
-		dvb_ca_en50221_init(adapter, dev->ci.en, 0, 1);
+		ret = dvb_ca_en50221_init(adapter, dev->ci.en, 0, 1);
+		if (ret != 0)
+			goto err;
 		set_transfer(chan, 1);
 		chan->dev->channel[2].DataFormatFlags = DF_SWAP32;
 		set_transfer(&chan->dev->channel[2], 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7134/saa7134-alsa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7134/saa7134-alsa.c
@@ -1214,7 +1214,7 @@
 
 static int saa7134_alsa_init(void)
 {
-	struct saa7134_dev *dev = NULL;
+	struct saa7134_dev *dev;
 
 	saa7134_dmasound_init = alsa_device_init;
 	saa7134_dmasound_exit = alsa_device_exit;
@@ -1229,7 +1229,7 @@
 			alsa_device_init(dev);
 	}
 
-	if (dev == NULL)
+	if (list_empty(&saa7134_devlist))
 		pr_info("saa7134 ALSA: no saa7134 cards found\n");
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7134/saa7134-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7134/saa7134-core.c
@@ -978,7 +978,7 @@
 	}
 	if (dev->radio_dev) {
 		if (video_is_registered(dev->radio_dev))
-			vb2_video_unregister_device(dev->radio_dev);
+			video_unregister_device(dev->radio_dev);
 		else
 			video_device_release(dev->radio_dev);
 		dev->radio_dev = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7134/saa7134-dvb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7134/saa7134-dvb.c
@@ -466,7 +466,9 @@
 	/* switch the board to analog mode */
 	if (fe->ops.i2c_gate_ctrl)
 		fe->ops.i2c_gate_ctrl(fe, 1);
-	i2c_transfer(&dev->i2c_adap, &analog_msg, 1);
+	if (i2c_transfer(&dev->i2c_adap, &analog_msg, 1) != 1)
+		return -EIO;
+
 	return 0;
 }
 
@@ -1018,7 +1020,9 @@
 	else
 		wbuf[1] = rbuf & 0xef;
 	msg[0].len = 2;
-	i2c_transfer(&dev->i2c_adap, msg, 1);
+	if (i2c_transfer(&dev->i2c_adap, msg, 1) != 1)
+		return -EIO;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7134/saa7134-ts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7134/saa7134-ts.c
@@ -300,6 +300,7 @@
 
 int saa7134_ts_fini(struct saa7134_dev *dev)
 {
+	del_timer_sync(&dev->ts_q.timeout);
 	saa7134_pgtable_free(dev->pci, &dev->ts_q.pt);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7134/saa7134-vbi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7134/saa7134-vbi.c
@@ -185,6 +185,7 @@
 int saa7134_vbi_fini(struct saa7134_dev *dev)
 {
 	/* nothing */
+	del_timer_sync(&dev->vbi_q.timeout);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7134/saa7134-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7134/saa7134-video.c
@@ -2153,6 +2153,7 @@
 
 void saa7134_video_fini(struct saa7134_dev *dev)
 {
+	del_timer_sync(&dev->video_q.timeout);
 	/* free stuff */
 	saa7134_pgtable_free(dev->pci, &dev->video_q.pt);
 	saa7134_pgtable_free(dev->pci, &dev->vbi_q.pt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7146/hexium_gemini.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7146/hexium_gemini.c
@@ -284,7 +284,12 @@
 	hexium_set_input(hexium, 0);
 	hexium->cur_input = 0;
 
-	saa7146_vv_init(dev, &vv_data);
+	ret = saa7146_vv_init(dev, &vv_data);
+	if (ret) {
+		i2c_del_adapter(&hexium->i2c_adapter);
+		kfree(hexium);
+		return ret;
+	}
 
 	vv_data.vid_ops.vidioc_enum_input = vidioc_enum_input;
 	vv_data.vid_ops.vidioc_g_input = vidioc_g_input;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7146/hexium_orion.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7146/hexium_orion.c
@@ -355,10 +355,16 @@
 static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
 {
 	struct hexium *hexium = (struct hexium *) dev->ext_priv;
+	int ret;
 
 	DEB_EE("\n");
 
-	saa7146_vv_init(dev, &vv_data);
+	ret = saa7146_vv_init(dev, &vv_data);
+	if (ret) {
+		pr_err("Error in saa7146_vv_init()\n");
+		return ret;
+	}
+
 	vv_data.vid_ops.vidioc_enum_input = vidioc_enum_input;
 	vv_data.vid_ops.vidioc_g_input = vidioc_g_input;
 	vv_data.vid_ops.vidioc_s_input = vidioc_s_input;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7146/mxb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7146/mxb.c
@@ -683,10 +683,16 @@
 static int mxb_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
 {
 	struct mxb *mxb;
+	int ret;
 
 	DEB_EE("dev:%p\n", dev);
 
-	saa7146_vv_init(dev, &vv_data);
+	ret = saa7146_vv_init(dev, &vv_data);
+	if (ret) {
+		ERR("Error in saa7146_vv_init()");
+		return ret;
+	}
+
 	if (mxb_probe(dev)) {
 		saa7146_vv_release(dev);
 		return -1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/saa7164/saa7164-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/saa7164/saa7164-core.c
@@ -1259,7 +1259,7 @@
 
 	if (saa7164_dev_setup(dev) < 0) {
 		err = -EINVAL;
-		goto fail_free;
+		goto fail_dev;
 	}
 
 	/* print pci info */
@@ -1427,6 +1427,8 @@
 
 fail_irq:
 	saa7164_dev_unregister(dev);
+fail_dev:
+	pci_disable_device(pci_dev);
 fail_free:
 	v4l2_device_unregister(&dev->v4l2_dev);
 	kfree(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/solo6x10/solo6x10-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/solo6x10/solo6x10-core.c
@@ -420,6 +420,7 @@
 		     solo_dev->nr_chans);
 
 	if (device_register(dev)) {
+		put_device(dev);
 		dev->parent = NULL;
 		return -ENOMEM;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/solo6x10/solo6x10-offsets.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/solo6x10/solo6x10-offsets.h
@@ -57,16 +57,16 @@
 #define SOLO_MP4E_EXT_ADDR(__solo) \
 	(SOLO_EREF_EXT_ADDR(__solo) + SOLO_EREF_EXT_AREA(__solo))
 #define SOLO_MP4E_EXT_SIZE(__solo) \
-	max((__solo->nr_chans * 0x00080000),				\
-	    min(((__solo->sdram_size - SOLO_MP4E_EXT_ADDR(__solo)) -	\
-		 __SOLO_JPEG_MIN_SIZE(__solo)), 0x00ff0000))
+	clamp(__solo->sdram_size - SOLO_MP4E_EXT_ADDR(__solo) -	\
+	      __SOLO_JPEG_MIN_SIZE(__solo),			\
+	      __solo->nr_chans * 0x00080000, 0x00ff0000)
 
 #define __SOLO_JPEG_MIN_SIZE(__solo)		(__solo->nr_chans * 0x00080000)
 #define SOLO_JPEG_EXT_ADDR(__solo) \
 		(SOLO_MP4E_EXT_ADDR(__solo) + SOLO_MP4E_EXT_SIZE(__solo))
 #define SOLO_JPEG_EXT_SIZE(__solo) \
-	max(__SOLO_JPEG_MIN_SIZE(__solo),				\
-	    min((__solo->sdram_size - SOLO_JPEG_EXT_ADDR(__solo)), 0x00ff0000))
+	clamp(__solo->sdram_size - SOLO_JPEG_EXT_ADDR(__solo),	\
+	      __SOLO_JPEG_MIN_SIZE(__solo), 0x00ff0000)
 
 #define SOLO_SDRAM_END(__solo) \
 	(SOLO_JPEG_EXT_ADDR(__solo) + SOLO_JPEG_EXT_SIZE(__solo))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/sta2x11/sta2x11_vip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/sta2x11/sta2x11_vip.c
@@ -760,7 +760,7 @@
 /**
  * vip_irq - interrupt routine
  * @irq: Number of interrupt ( not used, correct number is assumed )
- * @vip: local data structure containing all information
+ * @data: local data structure containing all information
  *
  * check for both frame interrupts set ( top and bottom ).
  * check FIFO overflow, but limit number of log messages after open.
@@ -770,8 +770,9 @@
  *
  * IRQ_HANDLED, interrupt done.
  */
-static irqreturn_t vip_irq(int irq, struct sta2x11_vip *vip)
+static irqreturn_t vip_irq(int irq, void *data)
 {
+	struct sta2x11_vip *vip = data;
 	unsigned int status;
 
 	status = reg_read(vip, DVP_ITS);
@@ -1053,9 +1054,7 @@
 
 	spin_lock_init(&vip->slock);
 
-	ret = request_irq(pdev->irq,
-			  (irq_handler_t) vip_irq,
-			  IRQF_SHARED, KBUILD_MODNAME, vip);
+	ret = request_irq(pdev->irq, vip_irq, IRQF_SHARED, KBUILD_MODNAME, vip);
 	if (ret) {
 		dev_err(&pdev->dev, "request_irq failed\n");
 		ret = -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/ttpci/budget-av.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/ttpci/budget-av.c
@@ -1462,7 +1462,8 @@
 		budget_av->has_saa7113 = 1;
 		err = saa7146_vv_init(dev, &vv_data);
 		if (err != 0) {
-			/* fixme: proper cleanup here */
+			ttpci_budget_deinit(&budget_av->budget);
+			kfree(budget_av);
 			ERR("cannot init vv subsystem\n");
 			return err;
 		}
@@ -1471,9 +1472,10 @@
 		vv_data.vid_ops.vidioc_s_input = vidioc_s_input;
 
 		if ((err = saa7146_register_device(&budget_av->vd, dev, "knc1", VFL_TYPE_VIDEO))) {
-			/* fixme: proper cleanup here */
-			ERR("cannot register capture v4l2 device\n");
 			saa7146_vv_release(dev);
+			ttpci_budget_deinit(&budget_av->budget);
+			kfree(budget_av);
+			ERR("cannot register capture v4l2 device\n");
 			return err;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/tw68/tw68-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/tw68/tw68-video.c
@@ -437,6 +437,7 @@
  */
 static int tw68_buf_prepare(struct vb2_buffer *vb)
 {
+	int ret;
 	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
 	struct vb2_queue *vq = vb->vb2_queue;
 	struct tw68_dev *dev = vb2_get_drv_priv(vq);
@@ -452,30 +453,30 @@
 	bpl = (dev->width * dev->fmt->depth) >> 3;
 	switch (dev->field) {
 	case V4L2_FIELD_TOP:
-		tw68_risc_buffer(dev->pci, buf, dma->sgl,
+		ret = tw68_risc_buffer(dev->pci, buf, dma->sgl,
 				 0, UNSET, bpl, 0, dev->height);
 		break;
 	case V4L2_FIELD_BOTTOM:
-		tw68_risc_buffer(dev->pci, buf, dma->sgl,
+		ret = tw68_risc_buffer(dev->pci, buf, dma->sgl,
 				 UNSET, 0, bpl, 0, dev->height);
 		break;
 	case V4L2_FIELD_SEQ_TB:
-		tw68_risc_buffer(dev->pci, buf, dma->sgl,
+		ret = tw68_risc_buffer(dev->pci, buf, dma->sgl,
 				 0, bpl * (dev->height >> 1),
 				 bpl, 0, dev->height >> 1);
 		break;
 	case V4L2_FIELD_SEQ_BT:
-		tw68_risc_buffer(dev->pci, buf, dma->sgl,
+		ret = tw68_risc_buffer(dev->pci, buf, dma->sgl,
 				 bpl * (dev->height >> 1), 0,
 				 bpl, 0, dev->height >> 1);
 		break;
 	case V4L2_FIELD_INTERLACED:
 	default:
-		tw68_risc_buffer(dev->pci, buf, dma->sgl,
+		ret = tw68_risc_buffer(dev->pci, buf, dma->sgl,
 				 0, bpl, bpl, bpl, dev->height >> 1);
 		break;
 	}
-	return 0;
+	return ret;
 }
 
 static void tw68_buf_finish(struct vb2_buffer *vb)
@@ -485,7 +486,8 @@
 	struct tw68_dev *dev = vb2_get_drv_priv(vq);
 	struct tw68_buf *buf = container_of(vbuf, struct tw68_buf, vb);
 
-	dma_free_coherent(&dev->pci->dev, buf->size, buf->cpu, buf->dma);
+	if (buf->cpu)
+		dma_free_coherent(&dev->pci->dev, buf->size, buf->cpu, buf->dma);
 }
 
 static int tw68_start_streaming(struct vb2_queue *q, unsigned int count)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/tw686x/tw686x-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/tw686x/tw686x-core.c
@@ -315,13 +315,6 @@
 
 	spin_lock_init(&dev->lock);
 
-	err = request_irq(pci_dev->irq, tw686x_irq, IRQF_SHARED,
-			  dev->name, dev);
-	if (err < 0) {
-		dev_err(&pci_dev->dev, "unable to request interrupt\n");
-		goto iounmap;
-	}
-
 	timer_setup(&dev->dma_delay_timer, tw686x_dma_delay, 0);
 
 	/*
@@ -333,18 +326,23 @@
 	err = tw686x_video_init(dev);
 	if (err) {
 		dev_err(&pci_dev->dev, "can't register video\n");
-		goto free_irq;
+		goto iounmap;
 	}
 
 	err = tw686x_audio_init(dev);
 	if (err)
 		dev_warn(&pci_dev->dev, "can't register audio\n");
 
+	err = request_irq(pci_dev->irq, tw686x_irq, IRQF_SHARED,
+			  dev->name, dev);
+	if (err < 0) {
+		dev_err(&pci_dev->dev, "unable to request interrupt\n");
+		goto iounmap;
+	}
+
 	pci_set_drvdata(pci_dev, dev);
 	return 0;
 
-free_irq:
-	free_irq(pci_dev->irq, dev);
 iounmap:
 	pci_iounmap(pci_dev, dev->mmio);
 free_region:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/pci/tw686x/tw686x-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/pci/tw686x/tw686x-video.c
@@ -1282,8 +1282,10 @@
 		video_set_drvdata(vdev, vc);
 
 		err = video_register_device(vdev, VFL_TYPE_VIDEO, -1);
-		if (err < 0)
+		if (err < 0) {
+			video_device_release(vdev);
 			goto error;
+		}
 		vc->num = vdev->num;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/allegro-dvt/allegro-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/allegro-dvt/allegro-core.c
@@ -1431,8 +1431,10 @@
 		INIT_LIST_HEAD(&buffer->head);
 
 		err = allegro_alloc_buffer(dev, buffer, size);
-		if (err)
+		if (err) {
+			kfree(buffer);
 			goto err;
+		}
 		list_add(&buffer->head, list);
 	}
 
@@ -2185,6 +2187,15 @@
 {
 	struct allegro_dev *dev = data;
 
+	/*
+	 * The firmware is initialized after the mailbox is setup. We further
+	 * check the AL5_ITC_CPU_IRQ_STA register, if the firmware actually
+	 * triggered the interrupt. Although this should not happen, make sure
+	 * that we ignore interrupts, if the mailbox is not initialized.
+	 */
+	if (!dev->mbox_status)
+		return IRQ_NONE;
+
 	allegro_mbox_notify(dev->mbox_status);
 
 	return IRQ_HANDLED;
@@ -3729,6 +3740,7 @@
 	if (ret < 0) {
 		v4l2_err(&dev->v4l2_dev,
 			 "failed to request firmware: %d\n", ret);
+		v4l2_device_unregister(&dev->v4l2_dev);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/am437x/am437x-vpfe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/am437x/am437x-vpfe.c
@@ -1499,7 +1499,9 @@
 			  struct v4l2_frmsizeenum *fsize)
 {
 	struct vpfe_device *vpfe = video_drvdata(file);
-	struct v4l2_subdev_frame_size_enum fse;
+	struct v4l2_subdev_frame_size_enum fse = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
 	struct v4l2_subdev *sd = vpfe->current_subdev->sd;
 	struct vpfe_fmt *fmt;
 	int ret;
@@ -1514,11 +1516,9 @@
 
 	memset(fsize->reserved, 0x0, sizeof(fsize->reserved));
 
-	memset(&fse, 0x0, sizeof(fse));
 	fse.index = fsize->index;
 	fse.pad = 0;
 	fse.code = fmt->code;
-	fse.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	ret = v4l2_subdev_call(sd, pad, enum_frame_size, NULL, &fse);
 	if (ret)
 		return ret;
@@ -2146,7 +2146,6 @@
 {
 	struct vpfe_device *vpfe = container_of(notifier->v4l2_dev,
 					       struct vpfe_device, v4l2_dev);
-	struct v4l2_subdev_mbus_code_enum mbus_code;
 	struct vpfe_subdev_info *sdinfo;
 	struct vpfe_fmt *fmt;
 	int ret = 0;
@@ -2173,9 +2172,11 @@
 
 	vpfe->num_active_fmt = 0;
 	for (j = 0, i = 0; (ret != -EINVAL); ++j) {
-		memset(&mbus_code, 0, sizeof(mbus_code));
-		mbus_code.index = j;
-		mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+		struct v4l2_subdev_mbus_code_enum mbus_code = {
+			.index = j,
+			.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		};
+
 		ret = v4l2_subdev_call(subdev, pad, enum_mbus_code,
 				       NULL, &mbus_code);
 		if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/aspeed-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/aspeed-video.c
@@ -151,7 +151,7 @@
 #define  VE_SRC_TB_EDGE_DET_BOT		GENMASK(28, VE_SRC_TB_EDGE_DET_BOT_SHF)
 
 #define VE_MODE_DETECT_STATUS		0x098
-#define  VE_MODE_DETECT_H_PIXELS	GENMASK(11, 0)
+#define  VE_MODE_DETECT_H_PERIOD	GENMASK(11, 0)
 #define  VE_MODE_DETECT_V_LINES_SHF	16
 #define  VE_MODE_DETECT_V_LINES		GENMASK(27, VE_MODE_DETECT_V_LINES_SHF)
 #define  VE_MODE_DETECT_STATUS_VSYNC	BIT(28)
@@ -162,6 +162,8 @@
 #define  VE_SYNC_STATUS_VSYNC_SHF	16
 #define  VE_SYNC_STATUS_VSYNC		GENMASK(27, VE_SYNC_STATUS_VSYNC_SHF)
 
+#define VE_H_TOTAL_PIXELS		0x0A0
+
 #define VE_INTERRUPT_CTRL		0x304
 #define VE_INTERRUPT_STATUS		0x308
 #define  VE_INTERRUPT_MODE_DETECT_WD	BIT(0)
@@ -500,6 +502,10 @@
 	aspeed_video_update(video, VE_INTERRUPT_CTRL, 0,
 			    VE_INTERRUPT_MODE_DETECT);
 
+	/* Disable mode detect in order to re-trigger */
+	aspeed_video_update(video, VE_SEQ_CTRL,
+			    VE_SEQ_CTRL_TRIG_MODE_DET, 0);
+
 	/* Trigger mode detect */
 	aspeed_video_update(video, VE_SEQ_CTRL, 0, VE_SEQ_CTRL_TRIG_MODE_DET);
 }
@@ -552,6 +558,8 @@
 	set_bit(VIDEO_RES_CHANGE, &video->flags);
 	clear_bit(VIDEO_FRAME_INPRG, &video->flags);
 
+	video->v4l2_input_status = V4L2_IN_ST_NO_SIGNAL;
+
 	aspeed_video_off(video);
 	aspeed_video_bufs_done(video, VB2_BUF_STATE_ERROR);
 
@@ -759,6 +767,7 @@
 	u32 src_lr_edge;
 	u32 src_tb_edge;
 	u32 sync;
+	u32 htotal;
 	struct v4l2_bt_timings *det = &video->detected_timings;
 
 	det->width = MIN_WIDTH;
@@ -786,10 +795,6 @@
 			return;
 		}
 
-		/* Disable mode detect in order to re-trigger */
-		aspeed_video_update(video, VE_SEQ_CTRL,
-				    VE_SEQ_CTRL_TRIG_MODE_DET, 0);
-
 		aspeed_video_check_and_set_polarity(video);
 
 		aspeed_video_enable_mode_detect(video);
@@ -807,6 +812,7 @@
 		src_tb_edge = aspeed_video_read(video, VE_SRC_TB_EDGE_DET);
 		mds = aspeed_video_read(video, VE_MODE_DETECT_STATUS);
 		sync = aspeed_video_read(video, VE_SYNC_STATUS);
+		htotal = aspeed_video_read(video, VE_H_TOTAL_PIXELS);
 
 		video->frame_bottom = (src_tb_edge & VE_SRC_TB_EDGE_DET_BOT) >>
 			VE_SRC_TB_EDGE_DET_BOT_SHF;
@@ -823,8 +829,7 @@
 			VE_SRC_LR_EDGE_DET_RT_SHF;
 		video->frame_left = src_lr_edge & VE_SRC_LR_EDGE_DET_LEFT;
 		det->hfrontporch = video->frame_left;
-		det->hbackporch = (mds & VE_MODE_DETECT_H_PIXELS) -
-			video->frame_right;
+		det->hbackporch = htotal - video->frame_right;
 		det->hsync = sync & VE_SYNC_STATUS_HSYNC;
 		if (video->frame_left > video->frame_right)
 			continue;
@@ -1337,7 +1342,6 @@
 	struct delayed_work *dwork = to_delayed_work(work);
 	struct aspeed_video *video = container_of(dwork, struct aspeed_video,
 						  res_work);
-	u32 input_status = video->v4l2_input_status;
 
 	aspeed_video_on(video);
 
@@ -1350,8 +1354,7 @@
 	aspeed_video_get_resolution(video);
 
 	if (video->detected_timings.width != video->active_timings.width ||
-	    video->detected_timings.height != video->active_timings.height ||
-	    input_status != video->v4l2_input_status) {
+	    video->detected_timings.height != video->active_timings.height) {
 		static const struct v4l2_event ev = {
 			.type = V4L2_EVENT_SOURCE_CHANGE,
 			.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
@@ -1720,6 +1723,7 @@
 
 	rc = aspeed_video_setup_video(video);
 	if (rc) {
+		aspeed_video_free_buf(video, &video->jpeg);
 		clk_unprepare(video->vclk);
 		clk_unprepare(video->eclk);
 		return rc;
@@ -1745,8 +1749,7 @@
 
 	v4l2_device_unregister(v4l2_dev);
 
-	dma_free_coherent(video->dev, VE_JPEG_HEADER_SIZE, video->jpeg.virt,
-			  video->jpeg.dma);
+	aspeed_video_free_buf(video, &video->jpeg);
 
 	of_reserved_mem_device_release(dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/atmel/atmel-isc-base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/atmel/atmel-isc-base.c
@@ -123,11 +123,9 @@
 	struct isc_clk *isc_clk = to_isc_clk(hw);
 	int ret;
 
-	if (isc_clk->id == ISC_ISPCK) {
-		ret = pm_runtime_resume_and_get(isc_clk->dev);
-		if (ret < 0)
-			return ret;
-	}
+	ret = pm_runtime_resume_and_get(isc_clk->dev);
+	if (ret < 0)
+		return ret;
 
 	return isc_wait_clk_stable(hw);
 }
@@ -138,8 +136,7 @@
 
 	isc_wait_clk_stable(hw);
 
-	if (isc_clk->id == ISC_ISPCK)
-		pm_runtime_put_sync(isc_clk->dev);
+	pm_runtime_put_sync(isc_clk->dev);
 }
 
 static int isc_clk_enable(struct clk_hw *hw)
@@ -186,16 +183,13 @@
 	u32 status;
 	int ret;
 
-	if (isc_clk->id == ISC_ISPCK) {
-		ret = pm_runtime_resume_and_get(isc_clk->dev);
-		if (ret < 0)
-			return 0;
-	}
+	ret = pm_runtime_resume_and_get(isc_clk->dev);
+	if (ret < 0)
+		return 0;
 
 	regmap_read(isc_clk->regmap, ISC_CLKSR, &status);
 
-	if (isc_clk->id == ISC_ISPCK)
-		pm_runtime_put_sync(isc_clk->dev);
+	pm_runtime_put_sync(isc_clk->dev);
 
 	return status & ISC_CLK(isc_clk->id) ? 1 : 0;
 }
@@ -325,6 +319,9 @@
 	const char *parent_names[3];
 	int num_parents;
 
+	if (id == ISC_ISPCK && !isc->ispck_required)
+		return 0;
+
 	num_parents = of_clk_get_parent_count(np);
 	if (num_parents < 1 || num_parents > 3)
 		return -EINVAL;
@@ -1372,14 +1369,12 @@
 			       struct v4l2_frmsizeenum *fsize)
 {
 	struct isc_device *isc = video_drvdata(file);
-	struct v4l2_subdev_frame_size_enum fse = {
-		.code = isc->config.sd_format->mbus_code,
-		.index = fsize->index,
-		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
-	};
 	int ret = -EINVAL;
 	int i;
 
+	if (fsize->index)
+		return -EINVAL;
+
 	for (i = 0; i < isc->num_user_formats; i++)
 		if (isc->user_formats[i]->fourcc == fsize->pixel_format)
 			ret = 0;
@@ -1391,14 +1386,14 @@
 	if (ret)
 		return ret;
 
-	ret = v4l2_subdev_call(isc->current_subdev->sd, pad, enum_frame_size,
-			       NULL, &fse);
-	if (ret)
-		return ret;
+	fsize->type = V4L2_FRMSIZE_TYPE_CONTINUOUS;
 
-	fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
-	fsize->discrete.width = fse.max_width;
-	fsize->discrete.height = fse.max_height;
+	fsize->stepwise.min_width = 16;
+	fsize->stepwise.max_width = isc->max_width;
+	fsize->stepwise.min_height = 16;
+	fsize->stepwise.max_height = isc->max_height;
+	fsize->stepwise.step_width = 1;
+	fsize->stepwise.step_height = 1;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/atmel/atmel-isc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/atmel/atmel-isc.h
@@ -178,6 +178,7 @@
  * @hclock:		Hclock clock input (refer datasheet)
  * @ispck:		iscpck clock (refer datasheet)
  * @isc_clks:		ISC clocks
+ * @ispck_required:	ISC requires ISP Clock initialization
  * @dcfg:		DMA master configuration, architecture dependent
  *
  * @dev:		Registered device driver
@@ -252,6 +253,7 @@
 	struct clk		*hclock;
 	struct clk		*ispck;
 	struct isc_clk		isc_clks[2];
+	bool			ispck_required;
 	u32			dcfg;
 
 	struct device		*dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/atmel/atmel-sama5d2-isc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/atmel/atmel-sama5d2-isc.c
@@ -267,7 +267,7 @@
 	 * Thus, if the YCYC mode is selected, replace it with the
 	 * sama5d2-compliant mode which is YYCC .
 	 */
-	if ((rlp_mode & ISC_RLP_CFG_MODE_YCYC) == ISC_RLP_CFG_MODE_YCYC) {
+	if ((rlp_mode & ISC_RLP_CFG_MODE_MASK) == ISC_RLP_CFG_MODE_YCYC) {
 		rlp_mode &= ~ISC_RLP_CFG_MODE_MASK;
 		rlp_mode |= ISC_RLP_CFG_MODE_YYCC;
 	}
@@ -454,6 +454,9 @@
 	/* sama5d2-isc - 8 bits per beat */
 	isc->dcfg = ISC_DCFG_YMBSIZE_BEATS8 | ISC_DCFG_CMBSIZE_BEATS8;
 
+	/* sama5d2-isc : ISPCK is required and mandatory */
+	isc->ispck_required = true;
+
 	ret = isc_pipeline_init(isc);
 	if (ret)
 		return ret;
@@ -476,22 +479,6 @@
 		dev_err(dev, "failed to init isc clock: %d\n", ret);
 		goto unprepare_hclk;
 	}
-
-	isc->ispck = isc->isc_clks[ISC_ISPCK].clk;
-
-	ret = clk_prepare_enable(isc->ispck);
-	if (ret) {
-		dev_err(dev, "failed to enable ispck: %d\n", ret);
-		goto unprepare_hclk;
-	}
-
-	/* ispck should be greater or equal to hclock */
-	ret = clk_set_rate(isc->ispck, clk_get_rate(isc->hclock));
-	if (ret) {
-		dev_err(dev, "failed to set ispck rate: %d\n", ret);
-		goto unprepare_clk;
-	}
-
 	ret = v4l2_device_register(dev, &isc->v4l2_dev);
 	if (ret) {
 		dev_err(dev, "unable to register v4l2 device.\n");
@@ -545,19 +532,38 @@
 	pm_runtime_enable(dev);
 	pm_request_idle(dev);
 
+	isc->ispck = isc->isc_clks[ISC_ISPCK].clk;
+
+	ret = clk_prepare_enable(isc->ispck);
+	if (ret) {
+		dev_err(dev, "failed to enable ispck: %d\n", ret);
+		goto disable_pm;
+	}
+
+	/* ispck should be greater or equal to hclock */
+	ret = clk_set_rate(isc->ispck, clk_get_rate(isc->hclock));
+	if (ret) {
+		dev_err(dev, "failed to set ispck rate: %d\n", ret);
+		goto unprepare_clk;
+	}
+
 	regmap_read(isc->regmap, ISC_VERSION + isc->offsets.version, &ver);
 	dev_info(dev, "Microchip ISC version %x\n", ver);
 
 	return 0;
 
+unprepare_clk:
+	clk_disable_unprepare(isc->ispck);
+
+disable_pm:
+	pm_runtime_disable(dev);
+
 cleanup_subdev:
 	isc_subdev_cleanup(isc);
 
 unregister_v4l2_device:
 	v4l2_device_unregister(&isc->v4l2_dev);
 
-unprepare_clk:
-	clk_disable_unprepare(isc->ispck);
 unprepare_hclk:
 	clk_disable_unprepare(isc->hclock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/atmel/atmel-sama7g5-isc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/atmel/atmel-sama7g5-isc.c
@@ -447,6 +447,9 @@
 	/* sama7g5-isc RAM access port is full AXI4 - 32 bits per beat */
 	isc->dcfg = ISC_DCFG_YMBSIZE_BEATS32 | ISC_DCFG_CMBSIZE_BEATS32;
 
+	/* sama7g5-isc : ISPCK does not exist, ISC is clocked by MCK */
+	isc->ispck_required = false;
+
 	ret = isc_pipeline_init(isc);
 	if (ret)
 		return ret;
@@ -470,25 +473,10 @@
 		goto unprepare_hclk;
 	}
 
-	isc->ispck = isc->isc_clks[ISC_ISPCK].clk;
-
-	ret = clk_prepare_enable(isc->ispck);
-	if (ret) {
-		dev_err(dev, "failed to enable ispck: %d\n", ret);
-		goto unprepare_hclk;
-	}
-
-	/* ispck should be greater or equal to hclock */
-	ret = clk_set_rate(isc->ispck, clk_get_rate(isc->hclock));
-	if (ret) {
-		dev_err(dev, "failed to set ispck rate: %d\n", ret);
-		goto unprepare_clk;
-	}
-
 	ret = v4l2_device_register(dev, &isc->v4l2_dev);
 	if (ret) {
 		dev_err(dev, "unable to register v4l2 device.\n");
-		goto unprepare_clk;
+		goto unprepare_hclk;
 	}
 
 	ret = xisc_parse_dt(dev, isc);
@@ -549,8 +537,6 @@
 unregister_v4l2_device:
 	v4l2_device_unregister(&isc->v4l2_dev);
 
-unprepare_clk:
-	clk_disable_unprepare(isc->ispck);
 unprepare_hclk:
 	clk_disable_unprepare(isc->hclock);
 
@@ -569,7 +555,6 @@
 
 	v4l2_device_unregister(&isc->v4l2_dev);
 
-	clk_disable_unprepare(isc->ispck);
 	clk_disable_unprepare(isc->hclock);
 
 	isc_clk_cleanup(isc);
@@ -581,7 +566,6 @@
 {
 	struct isc_device *isc = dev_get_drvdata(dev);
 
-	clk_disable_unprepare(isc->ispck);
 	clk_disable_unprepare(isc->hclock);
 
 	return 0;
@@ -596,10 +580,6 @@
 	if (ret)
 		return ret;
 
-	ret = clk_prepare_enable(isc->ispck);
-	if (ret)
-		clk_disable_unprepare(isc->hclock);
-
 	return ret;
 }
 
@@ -607,11 +587,13 @@
 	SET_RUNTIME_PM_OPS(xisc_runtime_suspend, xisc_runtime_resume, NULL)
 };
 
+#if IS_ENABLED(CONFIG_OF)
 static const struct of_device_id microchip_xisc_of_match[] = {
 	{ .compatible = "microchip,sama7g5-isc" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, microchip_xisc_of_match);
+#endif
 
 static struct platform_driver microchip_xisc_driver = {
 	.probe	= microchip_xisc_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/cadence/cdns-csi2rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/cadence/cdns-csi2rx.c
@@ -407,8 +407,10 @@
 							   fwh,
 							   struct v4l2_async_subdev);
 	of_node_put(ep);
-	if (IS_ERR(asd))
+	if (IS_ERR(asd)) {
+		v4l2_async_notifier_cleanup(&csi2rx->notifier);
 		return PTR_ERR(asd);
+	}
 
 	csi2rx->notifier.ops = &csi2rx_notifier_ops;
 
@@ -471,6 +473,7 @@
 	return 0;
 
 err_cleanup:
+	v4l2_async_notifier_unregister(&csi2rx->notifier);
 	v4l2_async_notifier_cleanup(&csi2rx->notifier);
 err_free_priv:
 	kfree(csi2rx);
@@ -481,6 +484,8 @@
 {
 	struct csi2rx_priv *csi2rx = platform_get_drvdata(pdev);
 
+	v4l2_async_notifier_unregister(&csi2rx->notifier);
+	v4l2_async_notifier_cleanup(&csi2rx->notifier);
 	v4l2_async_unregister_subdev(&csi2rx->subdev);
 	kfree(csi2rx);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/coda/coda-bit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/coda/coda-bit.c
@@ -852,7 +852,7 @@
 		/* Only H.264BP and H.263P3 are considered */
 		iram_info->buf_dbk_y_use = coda_iram_alloc(iram_info, w64);
 		iram_info->buf_dbk_c_use = coda_iram_alloc(iram_info, w64);
-		if (!iram_info->buf_dbk_c_use)
+		if (!iram_info->buf_dbk_y_use || !iram_info->buf_dbk_c_use)
 			goto out;
 		iram_info->axi_sram_use |= dbk_bits;
 
@@ -876,7 +876,7 @@
 
 		iram_info->buf_dbk_y_use = coda_iram_alloc(iram_info, w128);
 		iram_info->buf_dbk_c_use = coda_iram_alloc(iram_info, w128);
-		if (!iram_info->buf_dbk_c_use)
+		if (!iram_info->buf_dbk_y_use || !iram_info->buf_dbk_c_use)
 			goto out;
 		iram_info->axi_sram_use |= dbk_bits;
 
@@ -1082,10 +1082,16 @@
 	}
 
 	if (dst_fourcc == V4L2_PIX_FMT_JPEG) {
-		if (!ctx->params.jpeg_qmat_tab[0])
+		if (!ctx->params.jpeg_qmat_tab[0]) {
 			ctx->params.jpeg_qmat_tab[0] = kmalloc(64, GFP_KERNEL);
-		if (!ctx->params.jpeg_qmat_tab[1])
+			if (!ctx->params.jpeg_qmat_tab[0])
+				return -ENOMEM;
+		}
+		if (!ctx->params.jpeg_qmat_tab[1]) {
 			ctx->params.jpeg_qmat_tab[1] = kmalloc(64, GFP_KERNEL);
+			if (!ctx->params.jpeg_qmat_tab[1])
+				return -ENOMEM;
+		}
 		coda_set_jpeg_compression_quality(ctx, ctx->params.jpeg_quality);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/coda/coda-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/coda/coda-common.c
@@ -408,6 +408,7 @@
 	if (!vdoa_data)
 		vdoa_data = ERR_PTR(-EPROBE_DEFER);
 
+	put_device(&vdoa_pdev->dev);
 out:
 	of_node_put(vdoa_node);
 
@@ -1317,7 +1318,8 @@
 				    struct v4l2_frmivalenum *f)
 {
 	struct coda_ctx *ctx = fh_to_ctx(fh);
-	int i;
+	struct coda_q_data *q_data;
+	const struct coda_codec *codec;
 
 	if (f->index)
 		return -EINVAL;
@@ -1326,12 +1328,19 @@
 	if (!ctx->vdoa && f->pixel_format == V4L2_PIX_FMT_YUYV)
 		return -EINVAL;
 
-	for (i = 0; i < CODA_MAX_FORMATS; i++) {
-		if (f->pixel_format == ctx->cvd->src_formats[i] ||
-		    f->pixel_format == ctx->cvd->dst_formats[i])
-			break;
+	if (coda_format_normalize_yuv(f->pixel_format) == V4L2_PIX_FMT_YUV420) {
+		q_data = get_q_data(ctx, V4L2_BUF_TYPE_VIDEO_CAPTURE);
+		codec = coda_find_codec(ctx->dev, f->pixel_format,
+					q_data->fourcc);
+	} else {
+		codec = coda_find_codec(ctx->dev, V4L2_PIX_FMT_YUV420,
+					f->pixel_format);
 	}
-	if (i == CODA_MAX_FORMATS)
+	if (!codec)
+		return -EINVAL;
+
+	if (f->width < MIN_W || f->width > codec->max_w ||
+	    f->height < MIN_H || f->height > codec->max_h)
 		return -EINVAL;
 
 	f->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
@@ -1537,11 +1546,13 @@
 
 	if (!wait_for_completion_timeout(&ctx->completion,
 					 msecs_to_jiffies(1000))) {
-		dev_err(dev->dev, "CODA PIC_RUN timeout\n");
+		if (ctx->use_bit) {
+			dev_err(dev->dev, "CODA PIC_RUN timeout\n");
 
-		ctx->hold = true;
+			ctx->hold = true;
 
-		coda_hw_reset(ctx);
+			coda_hw_reset(ctx);
+		}
 
 		if (ctx->ops->run_timeout)
 			ctx->ops->run_timeout(ctx);
@@ -2335,8 +2346,8 @@
 		V4L2_CID_MPEG_VIDEO_H264_CHROMA_QP_INDEX_OFFSET, -12, 12, 1, 0);
 	v4l2_ctrl_new_std_menu(&ctx->ctrls, &coda_ctrl_ops,
 		V4L2_CID_MPEG_VIDEO_H264_PROFILE,
-		V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE, 0x0,
-		V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE);
+		V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_BASELINE, 0x0,
+		V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_BASELINE);
 	if (ctx->dev->devtype->product == CODA_HX4 ||
 	    ctx->dev->devtype->product == CODA_7541) {
 		v4l2_ctrl_new_std_menu(&ctx->ctrls, &coda_ctrl_ops,
@@ -2350,12 +2361,15 @@
 	if (ctx->dev->devtype->product == CODA_960) {
 		v4l2_ctrl_new_std_menu(&ctx->ctrls, &coda_ctrl_ops,
 			V4L2_CID_MPEG_VIDEO_H264_LEVEL,
-			V4L2_MPEG_VIDEO_H264_LEVEL_4_0,
-			~((1 << V4L2_MPEG_VIDEO_H264_LEVEL_2_0) |
+			V4L2_MPEG_VIDEO_H264_LEVEL_4_2,
+			~((1 << V4L2_MPEG_VIDEO_H264_LEVEL_1_0) |
+			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_2_0) |
 			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_3_0) |
 			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_3_1) |
 			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_3_2) |
-			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_4_0)),
+			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_4_0) |
+			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_4_1) |
+			  (1 << V4L2_MPEG_VIDEO_H264_LEVEL_4_2)),
 			V4L2_MPEG_VIDEO_H264_LEVEL_4_0);
 	}
 	v4l2_ctrl_new_std(&ctx->ctrls, &coda_ctrl_ops,
@@ -2417,7 +2431,7 @@
 	ctx->h264_profile_ctrl = v4l2_ctrl_new_std_menu(&ctx->ctrls,
 		&coda_ctrl_ops, V4L2_CID_MPEG_VIDEO_H264_PROFILE,
 		V4L2_MPEG_VIDEO_H264_PROFILE_HIGH,
-		~((1 << V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE) |
+		~((1 << V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_BASELINE) |
 		  (1 << V4L2_MPEG_VIDEO_H264_PROFILE_MAIN) |
 		  (1 << V4L2_MPEG_VIDEO_H264_PROFILE_HIGH)),
 		V4L2_MPEG_VIDEO_H264_PROFILE_HIGH);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/coda/coda-jpeg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/coda/coda-jpeg.c
@@ -1052,10 +1052,16 @@
 		v4l2_err(&dev->v4l2_dev, "error loading Huffman tables\n");
 		return ret;
 	}
-	if (!ctx->params.jpeg_qmat_tab[0])
+	if (!ctx->params.jpeg_qmat_tab[0]) {
 		ctx->params.jpeg_qmat_tab[0] = kmalloc(64, GFP_KERNEL);
-	if (!ctx->params.jpeg_qmat_tab[1])
+		if (!ctx->params.jpeg_qmat_tab[0])
+			return -ENOMEM;
+	}
+	if (!ctx->params.jpeg_qmat_tab[1]) {
 		ctx->params.jpeg_qmat_tab[1] = kmalloc(64, GFP_KERNEL);
+		if (!ctx->params.jpeg_qmat_tab[1])
+			return -ENOMEM;
+	}
 	coda_set_jpeg_compression_quality(ctx, ctx->params.jpeg_quality);
 
 	return 0;
@@ -1127,7 +1133,8 @@
 	coda_write(dev, 0, CODA9_REG_JPEG_GBU_BT_PTR);
 	coda_write(dev, 0, CODA9_REG_JPEG_GBU_WD_PTR);
 	coda_write(dev, 0, CODA9_REG_JPEG_GBU_BBSR);
-	coda_write(dev, 0, CODA9_REG_JPEG_BBC_STRM_CTRL);
+	coda_write(dev, BIT(31) | ((end_addr - start_addr - header_len) / 256),
+		   CODA9_REG_JPEG_BBC_STRM_CTRL);
 	coda_write(dev, 0, CODA9_REG_JPEG_GBU_CTRL);
 	coda_write(dev, 0, CODA9_REG_JPEG_GBU_FF_RPTR);
 	coda_write(dev, 127, CODA9_REG_JPEG_GBU_BBER);
@@ -1257,6 +1264,23 @@
 	coda_hw_reset(ctx);
 }
 
+static void coda9_jpeg_encode_timeout(struct coda_ctx *ctx)
+{
+	struct coda_dev *dev = ctx->dev;
+	u32 end_addr, wr_ptr;
+
+	/* Handle missing BBC overflow interrupt via timeout */
+	end_addr = coda_read(dev, CODA9_REG_JPEG_BBC_END_ADDR);
+	wr_ptr = coda_read(dev, CODA9_REG_JPEG_BBC_WR_PTR);
+	if (wr_ptr >= end_addr - 256) {
+		v4l2_err(&dev->v4l2_dev, "JPEG too large for capture buffer\n");
+		coda9_jpeg_finish_encode(ctx);
+		return;
+	}
+
+	coda_hw_reset(ctx);
+}
+
 static void coda9_jpeg_release(struct coda_ctx *ctx)
 {
 	int i;
@@ -1276,6 +1300,7 @@
 	.start_streaming = coda9_jpeg_start_encoding,
 	.prepare_run = coda9_jpeg_prepare_encode,
 	.finish_run = coda9_jpeg_finish_encode,
+	.run_timeout = coda9_jpeg_encode_timeout,
 	.release = coda9_jpeg_release,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/coda/imx-vdoa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/coda/imx-vdoa.c
@@ -287,7 +287,11 @@
 	struct resource *res;
 	int ret;
 
-	dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(&pdev->dev, "DMA enable failed\n");
+		return ret;
+	}
 
 	vdoa = devm_kzalloc(&pdev->dev, sizeof(*vdoa), GFP_KERNEL);
 	if (!vdoa)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/davinci/vpif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/davinci/vpif.c
@@ -41,6 +41,11 @@
 #define VPIF_CH2_MAX_MODES	15
 #define VPIF_CH3_MAX_MODES	2
 
+struct vpif_data {
+	struct platform_device *capture;
+	struct platform_device *display;
+};
+
 DEFINE_SPINLOCK(vpif_lock);
 EXPORT_SYMBOL_GPL(vpif_lock);
 
@@ -423,17 +428,32 @@
 }
 EXPORT_SYMBOL(vpif_channel_getfid);
 
+static void vpif_pdev_release(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	kfree(pdev);
+}
+
 static int vpif_probe(struct platform_device *pdev)
 {
 	static struct resource	*res, *res_irq;
 	struct platform_device *pdev_capture, *pdev_display;
 	struct device_node *endpoint = NULL;
+	struct vpif_data *data;
+	int ret;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	vpif_base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(vpif_base))
 		return PTR_ERR(vpif_base);
 
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, data);
+
 	pm_runtime_enable(&pdev->dev);
 	pm_runtime_get(&pdev->dev);
 
@@ -457,46 +477,79 @@
 	res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (!res_irq) {
 		dev_warn(&pdev->dev, "Missing IRQ resource.\n");
-		pm_runtime_put(&pdev->dev);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_put_rpm;
 	}
 
-	pdev_capture = devm_kzalloc(&pdev->dev, sizeof(*pdev_capture),
-				    GFP_KERNEL);
-	if (pdev_capture) {
-		pdev_capture->name = "vpif_capture";
-		pdev_capture->id = -1;
-		pdev_capture->resource = res_irq;
-		pdev_capture->num_resources = 1;
-		pdev_capture->dev.dma_mask = pdev->dev.dma_mask;
-		pdev_capture->dev.coherent_dma_mask = pdev->dev.coherent_dma_mask;
-		pdev_capture->dev.parent = &pdev->dev;
-		platform_device_register(pdev_capture);
-	} else {
-		dev_warn(&pdev->dev, "Unable to allocate memory for pdev_capture.\n");
+	pdev_capture = kzalloc(sizeof(*pdev_capture), GFP_KERNEL);
+	if (!pdev_capture) {
+		ret = -ENOMEM;
+		goto err_put_rpm;
 	}
 
-	pdev_display = devm_kzalloc(&pdev->dev, sizeof(*pdev_display),
-				    GFP_KERNEL);
-	if (pdev_display) {
-		pdev_display->name = "vpif_display";
-		pdev_display->id = -1;
-		pdev_display->resource = res_irq;
-		pdev_display->num_resources = 1;
-		pdev_display->dev.dma_mask = pdev->dev.dma_mask;
-		pdev_display->dev.coherent_dma_mask = pdev->dev.coherent_dma_mask;
-		pdev_display->dev.parent = &pdev->dev;
-		platform_device_register(pdev_display);
-	} else {
-		dev_warn(&pdev->dev, "Unable to allocate memory for pdev_display.\n");
+	pdev_capture->name = "vpif_capture";
+	pdev_capture->id = -1;
+	pdev_capture->resource = res_irq;
+	pdev_capture->num_resources = 1;
+	pdev_capture->dev.dma_mask = pdev->dev.dma_mask;
+	pdev_capture->dev.coherent_dma_mask = pdev->dev.coherent_dma_mask;
+	pdev_capture->dev.parent = &pdev->dev;
+	pdev_capture->dev.release = vpif_pdev_release;
+
+	ret = platform_device_register(pdev_capture);
+	if (ret)
+		goto err_put_pdev_capture;
+
+	pdev_display = kzalloc(sizeof(*pdev_display), GFP_KERNEL);
+	if (!pdev_display) {
+		ret = -ENOMEM;
+		goto err_put_pdev_capture;
 	}
 
+	pdev_display->name = "vpif_display";
+	pdev_display->id = -1;
+	pdev_display->resource = res_irq;
+	pdev_display->num_resources = 1;
+	pdev_display->dev.dma_mask = pdev->dev.dma_mask;
+	pdev_display->dev.coherent_dma_mask = pdev->dev.coherent_dma_mask;
+	pdev_display->dev.parent = &pdev->dev;
+	pdev_display->dev.release = vpif_pdev_release;
+
+	ret = platform_device_register(pdev_display);
+	if (ret)
+		goto err_put_pdev_display;
+
+	data->capture = pdev_capture;
+	data->display = pdev_display;
+
 	return 0;
+
+err_put_pdev_display:
+	platform_device_put(pdev_display);
+err_put_pdev_capture:
+	platform_device_put(pdev_capture);
+err_put_rpm:
+	pm_runtime_put(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	kfree(data);
+
+	return ret;
 }
 
 static int vpif_remove(struct platform_device *pdev)
 {
+	struct vpif_data *data = platform_get_drvdata(pdev);
+
+	if (data->capture)
+		platform_device_unregister(data->capture);
+	if (data->display)
+		platform_device_unregister(data->display);
+
+	pm_runtime_put(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
+
+	kfree(data);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/exynos4-is/fimc-capture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/exynos4-is/fimc-capture.c
@@ -763,7 +763,10 @@
 	struct fimc_dev *fimc = ctx->fimc_dev;
 	struct fimc_pipeline *p = to_fimc_pipeline(fimc->vid_cap.ve.pipe);
 	struct v4l2_subdev *sd = p->subdevs[IDX_SENSOR];
-	struct v4l2_subdev_format sfmt;
+	struct v4l2_subdev_format sfmt = {
+		.which = set ? V4L2_SUBDEV_FORMAT_ACTIVE
+		       : V4L2_SUBDEV_FORMAT_TRY,
+	};
 	struct v4l2_mbus_framefmt *mf = &sfmt.format;
 	struct media_entity *me;
 	struct fimc_fmt *ffmt;
@@ -774,9 +777,7 @@
 	if (WARN_ON(!sd || !tfmt))
 		return -EINVAL;
 
-	memset(&sfmt, 0, sizeof(sfmt));
 	sfmt.format = *tfmt;
-	sfmt.which = set ? V4L2_SUBDEV_FORMAT_ACTIVE : V4L2_SUBDEV_FORMAT_TRY;
 
 	me = fimc_pipeline_get_head(&sd->entity);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/exynos4-is/fimc-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/exynos4-is/fimc-core.c
@@ -1174,7 +1174,7 @@
 	return platform_driver_register(&fimc_driver);
 }
 
-void __exit fimc_unregister_driver(void)
+void fimc_unregister_driver(void)
 {
 	platform_driver_unregister(&fimc_driver);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/exynos4-is/fimc-is.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/exynos4-is/fimc-is.c
@@ -140,7 +140,7 @@
 			dev_err(&is->pdev->dev, "clock %s enable failed\n",
 				fimc_is_clocks[i]);
 			for (--i; i >= 0; i--)
-				clk_disable(is->clocks[i]);
+				clk_disable_unprepare(is->clocks[i]);
 			return ret;
 		}
 		pr_debug("enabled clock: %s\n", fimc_is_clocks[i]);
@@ -213,6 +213,7 @@
 
 			if (ret < 0 || index >= FIMC_IS_SENSORS_NUM) {
 				of_node_put(child);
+				of_node_put(i2c_bus);
 				return ret;
 			}
 			index++;
@@ -830,7 +831,7 @@
 
 	ret = pm_runtime_resume_and_get(dev);
 	if (ret < 0)
-		goto err_irq;
+		goto err_pm_disable;
 
 	vb2_dma_contig_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
@@ -864,6 +865,8 @@
 	pm_runtime_put_noidle(dev);
 	if (!pm_runtime_enabled(dev))
 		fimc_is_runtime_suspend(dev);
+err_pm_disable:
+	pm_runtime_disable(dev);
 err_irq:
 	free_irq(is->irq, is);
 err_clk:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/exynos4-is/fimc-isp-video.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/exynos4-is/fimc-isp-video.h
@@ -32,7 +32,7 @@
 	return 0;
 }
 
-void fimc_isp_video_device_unregister(struct fimc_isp *isp,
+static inline void fimc_isp_video_device_unregister(struct fimc_isp *isp,
 				enum v4l2_buf_type type)
 {
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/exynos4-is/media-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/exynos4-is/media-dev.c
@@ -1380,9 +1380,7 @@
 
 	/* Find platform data for this sensor subdev */
 	for (i = 0; i < ARRAY_SIZE(fmd->sensor); i++)
-		if (fmd->sensor[i].asd &&
-		    fmd->sensor[i].asd->match.fwnode ==
-		    of_fwnode_handle(subdev->dev->of_node))
+		if (fmd->sensor[i].asd == asd)
 			si = &fmd->sensor[i];
 
 	if (si == NULL)
@@ -1474,7 +1472,7 @@
 	pinctrl = devm_pinctrl_get(dev);
 	if (IS_ERR(pinctrl)) {
 		ret = PTR_ERR(pinctrl);
-		if (ret != EPROBE_DEFER)
+		if (ret != -EPROBE_DEFER)
 			dev_err(dev, "Failed to get pinctrl: %d\n", ret);
 		goto err_clk;
 	}
@@ -1586,7 +1584,11 @@
 	if (ret)
 		return ret;
 
-	return platform_driver_register(&fimc_md_driver);
+	ret = platform_driver_register(&fimc_md_driver);
+	if (ret)
+		fimc_unregister_driver();
+
+	return ret;
 }
 
 static void __exit fimc_md_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/exynos4-is/mipi-csis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/exynos4-is/mipi-csis.c
@@ -942,13 +942,19 @@
 					       state->supplies);
 			goto unlock;
 		}
-		clk_enable(state->clock[CSIS_CLK_GATE]);
+		ret = clk_enable(state->clock[CSIS_CLK_GATE]);
+		if (ret) {
+			phy_power_off(state->phy);
+			regulator_bulk_disable(CSIS_NUM_SUPPLIES,
+					       state->supplies);
+			goto unlock;
+		}
 	}
 	if (state->flags & ST_STREAMING)
 		s5pcsis_start_stream(state);
 
 	state->flags &= ~ST_SUSPENDED;
- unlock:
+unlock:
 	mutex_unlock(&state->lock);
 	return ret ? -EAGAIN : 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/imx-jpeg/mxc-jpeg-hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/imx-jpeg/mxc-jpeg-hw.c
@@ -76,7 +76,14 @@
 
 void mxc_jpeg_enable_irq(void __iomem *reg, int slot)
 {
-	writel(0xFFFFFFFF, reg + MXC_SLOT_OFFSET(slot, SLOT_IRQ_EN));
+	writel(0xFFFFFFFF, reg + MXC_SLOT_OFFSET(slot, SLOT_STATUS));
+	writel(0xF0C, reg + MXC_SLOT_OFFSET(slot, SLOT_IRQ_EN));
+}
+
+void mxc_jpeg_disable_irq(void __iomem *reg, int slot)
+{
+	writel(0x0, reg + MXC_SLOT_OFFSET(slot, SLOT_IRQ_EN));
+	writel(0xFFFFFFFF, reg + MXC_SLOT_OFFSET(slot, SLOT_STATUS));
 }
 
 void mxc_jpeg_sw_reset(void __iomem *reg)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/imx-jpeg/mxc-jpeg-hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/imx-jpeg/mxc-jpeg-hw.h
@@ -53,10 +53,10 @@
 #define CAST_REC_REGS_SEL		CAST_STATUS4
 #define CAST_LUMTH			CAST_STATUS5
 #define CAST_CHRTH			CAST_STATUS6
-#define CAST_NOMFRSIZE_LO		CAST_STATUS7
-#define CAST_NOMFRSIZE_HI		CAST_STATUS8
-#define CAST_OFBSIZE_LO			CAST_STATUS9
-#define CAST_OFBSIZE_HI			CAST_STATUS10
+#define CAST_NOMFRSIZE_LO		CAST_STATUS16
+#define CAST_NOMFRSIZE_HI		CAST_STATUS17
+#define CAST_OFBSIZE_LO			CAST_STATUS18
+#define CAST_OFBSIZE_HI			CAST_STATUS19
 
 #define MXC_MAX_SLOTS	1 /* TODO use all 4 slots*/
 /* JPEG-Decoder Wrapper Slot Registers 0..3 */
@@ -125,6 +125,7 @@
 void mxc_jpeg_enable_slot(void __iomem *reg, int slot);
 void mxc_jpeg_set_l_endian(void __iomem *reg, int le);
 void mxc_jpeg_enable_irq(void __iomem *reg, int slot);
+void mxc_jpeg_disable_irq(void __iomem *reg, int slot);
 int mxc_jpeg_set_input(void __iomem *reg, u32 in_buf, u32 bufsize);
 int mxc_jpeg_set_output(void __iomem *reg, u16 out_pitch, u32 out_buf,
 			u16 w, u16 h);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/imx-jpeg/mxc-jpeg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/imx-jpeg/mxc-jpeg.c
@@ -49,6 +49,7 @@
 #include <linux/slab.h>
 #include <linux/irqreturn.h>
 #include <linux/interrupt.h>
+#include <linux/pm_runtime.h>
 #include <linux/pm_domain.h>
 #include <linux/string.h>
 
@@ -81,6 +82,7 @@
 		.h_align	= 3,
 		.v_align	= 3,
 		.flags		= MXC_JPEG_FMT_TYPE_RAW,
+		.precision	= 8,
 	},
 	{
 		.name		= "ARGB", /* ARGBARGB packed format */
@@ -92,10 +94,11 @@
 		.h_align	= 3,
 		.v_align	= 3,
 		.flags		= MXC_JPEG_FMT_TYPE_RAW,
+		.precision	= 8,
 	},
 	{
 		.name		= "YUV420", /* 1st plane = Y, 2nd plane = UV */
-		.fourcc		= V4L2_PIX_FMT_NV12,
+		.fourcc		= V4L2_PIX_FMT_NV12M,
 		.subsampling	= V4L2_JPEG_CHROMA_SUBSAMPLING_420,
 		.nc		= 3,
 		.depth		= 12, /* 6 bytes (4Y + UV) for 4 pixels */
@@ -103,6 +106,7 @@
 		.h_align	= 4,
 		.v_align	= 4,
 		.flags		= MXC_JPEG_FMT_TYPE_RAW,
+		.precision	= 8,
 	},
 	{
 		.name		= "YUV422", /* YUYV */
@@ -114,6 +118,7 @@
 		.h_align	= 4,
 		.v_align	= 3,
 		.flags		= MXC_JPEG_FMT_TYPE_RAW,
+		.precision	= 8,
 	},
 	{
 		.name		= "YUV444", /* YUVYUV */
@@ -125,6 +130,7 @@
 		.h_align	= 3,
 		.v_align	= 3,
 		.flags		= MXC_JPEG_FMT_TYPE_RAW,
+		.precision	= 8,
 	},
 	{
 		.name		= "Gray", /* Gray (Y8/Y12) or Single Comp */
@@ -136,6 +142,7 @@
 		.h_align	= 3,
 		.v_align	= 3,
 		.flags		= MXC_JPEG_FMT_TYPE_RAW,
+		.precision	= 8,
 	},
 };
 
@@ -294,6 +301,9 @@
 	/* mxc-jpeg specific */
 	bool			dht_needed;
 	bool			jpeg_parse_error;
+	const struct mxc_jpeg_fmt	*fmt;
+	int			w;
+	int			h;
 };
 
 static inline struct mxc_jpeg_src_buf *vb2_to_mxc_buf(struct vb2_buffer *vb)
@@ -306,6 +316,9 @@
 module_param(debug, int, 0644);
 MODULE_PARM_DESC(debug, "Debug level (0-3)");
 
+static void mxc_jpeg_bytesperline(struct mxc_jpeg_q_data *q, u32 precision);
+static void mxc_jpeg_sizeimage(struct mxc_jpeg_q_data *q);
+
 static void _bswap16(u16 *a)
 {
 	*a = ((*a & 0x00FF) << 8) | ((*a & 0xFF00) >> 8);
@@ -389,7 +402,7 @@
 		return MXC_JPEG_GRAY;
 	case V4L2_PIX_FMT_YUYV:
 		return MXC_JPEG_YUV422;
-	case V4L2_PIX_FMT_NV12:
+	case V4L2_PIX_FMT_NV12M:
 		return MXC_JPEG_YUV420;
 	case V4L2_PIX_FMT_YUV24:
 		return MXC_JPEG_YUV444;
@@ -493,6 +506,7 @@
 				     GFP_ATOMIC);
 	if (!cfg_stm)
 		goto err;
+	memset(cfg_stm, 0, MXC_JPEG_MAX_CFG_STREAM);
 	jpeg->slot_data[slot].cfg_stream_vaddr = cfg_stm;
 
 skip_alloc:
@@ -531,6 +545,18 @@
 	jpeg->slot_data[slot].used = false;
 }
 
+static void mxc_jpeg_check_and_set_last_buffer(struct mxc_jpeg_ctx *ctx,
+					       struct vb2_v4l2_buffer *src_buf,
+					       struct vb2_v4l2_buffer *dst_buf)
+{
+	if (v4l2_m2m_is_last_draining_src_buf(ctx->fh.m2m_ctx, src_buf)) {
+		dst_buf->flags |= V4L2_BUF_FLAG_LAST;
+		v4l2_m2m_mark_stopped(ctx->fh.m2m_ctx);
+		notify_eos(ctx);
+		ctx->header_parsed = false;
+	}
+}
+
 static irqreturn_t mxc_jpeg_dec_irq(int irq, void *priv)
 {
 	struct mxc_jpeg_dev *jpeg = priv;
@@ -553,15 +579,8 @@
 	dev_dbg(dev, "Irq %d on slot %d.\n", irq, slot);
 
 	ctx = v4l2_m2m_get_curr_priv(jpeg->m2m_dev);
-	if (!ctx) {
-		dev_err(dev,
-			"Instance released before the end of transaction.\n");
-		/* soft reset only resets internal state, not registers */
-		mxc_jpeg_sw_reset(reg);
-		/* clear all interrupts */
-		writel(0xFFFFFFFF, reg + MXC_SLOT_OFFSET(slot, SLOT_STATUS));
+	if (WARN_ON(!ctx))
 		goto job_unlock;
-	}
 
 	if (slot != ctx->slot) {
 		/* TODO investigate when adding multi-instance support */
@@ -575,6 +594,10 @@
 
 	dst_buf = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx);
 	src_buf = v4l2_m2m_next_src_buf(ctx->fh.m2m_ctx);
+	if (!dst_buf || !src_buf) {
+		dev_err(dev, "No source or destination buffer.\n");
+		goto job_unlock;
+	}
 	jpeg_src_buf = vb2_to_mxc_buf(&src_buf->vb2_buf);
 
 	if (dec_ret & SLOT_STATUS_ENC_CONFIG_ERR) {
@@ -601,6 +624,7 @@
 		dev_dbg(dev, "Decoder DHT cfg finished. Start decoding...\n");
 		goto job_unlock;
 	}
+
 	if (jpeg->mode == MXC_JPEG_ENCODE) {
 		payload = readl(reg + MXC_SLOT_OFFSET(slot, SLOT_BUF_PTR));
 		vb2_set_plane_payload(&dst_buf->vb2_buf, 0, payload);
@@ -628,7 +652,9 @@
 	buf_state = VB2_BUF_STATE_DONE;
 
 buffers_done:
+	mxc_jpeg_disable_irq(reg, ctx->slot);
 	jpeg->slot_data[slot].used = false; /* unused, but don't free */
+	mxc_jpeg_check_and_set_last_buffer(ctx, src_buf, dst_buf);
 	v4l2_m2m_src_buf_remove(ctx->fh.m2m_ctx);
 	v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
 	v4l2_m2m_buf_done(src_buf, buf_state);
@@ -654,7 +680,7 @@
 	_bswap16(&sof->width);
 
 	switch (fourcc) {
-	case V4L2_PIX_FMT_NV12:
+	case V4L2_PIX_FMT_NV12M:
 		sof->components_no = 3;
 		sof->comp[0].v = 0x2;
 		sof->comp[0].h = 0x2;
@@ -690,7 +716,7 @@
 	u8 *sof_u8 = (u8 *)sos;
 
 	switch (fourcc) {
-	case V4L2_PIX_FMT_NV12:
+	case V4L2_PIX_FMT_NV12M:
 		sos->components_no = 3;
 		break;
 	case V4L2_PIX_FMT_YUYV:
@@ -724,7 +750,13 @@
 					      u32 fourcc,
 					      u16 w, u16 h)
 {
-	unsigned int offset = 0;
+	/*
+	 * There is a hardware issue that first 128 bytes of configuration data
+	 * can't be loaded correctly.
+	 * To avoid this issue, we need to write the configuration from
+	 * an offset which should be no less than 0x80 (128 bytes).
+	 */
+	unsigned int offset = 0x80;
 	u8 *cfg = (u8 *)cfg_stream_vaddr;
 	struct mxc_jpeg_sof *sof;
 	struct mxc_jpeg_sos *sos;
@@ -851,8 +883,8 @@
 	jpeg->slot_data[slot].cfg_stream_size =
 			mxc_jpeg_setup_cfg_stream(cfg_stream_vaddr,
 						  q_data->fmt->fourcc,
-						  q_data->w_adjusted,
-						  q_data->h_adjusted);
+						  q_data->w,
+						  q_data->h);
 
 	/* chain the config descriptor with the encoding descriptor */
 	cfg_desc->next_descpt_ptr = desc_handle | MXC_NXT_DESCPT_EN;
@@ -890,6 +922,67 @@
 	mxc_jpeg_set_desc(cfg_desc_handle, reg, slot);
 }
 
+static bool mxc_jpeg_source_change(struct mxc_jpeg_ctx *ctx,
+				   struct mxc_jpeg_src_buf *jpeg_src_buf)
+{
+	struct device *dev = ctx->mxc_jpeg->dev;
+	struct mxc_jpeg_q_data *q_data_cap;
+
+	if (!jpeg_src_buf->fmt)
+		return false;
+
+	q_data_cap = mxc_jpeg_get_q_data(ctx, V4L2_BUF_TYPE_VIDEO_CAPTURE);
+	if (q_data_cap->fmt != jpeg_src_buf->fmt ||
+	    q_data_cap->w != jpeg_src_buf->w ||
+	    q_data_cap->h != jpeg_src_buf->h) {
+		dev_dbg(dev, "Detected jpeg res=(%dx%d)->(%dx%d), pixfmt=%c%c%c%c\n",
+			q_data_cap->w, q_data_cap->h,
+			jpeg_src_buf->w, jpeg_src_buf->h,
+			(jpeg_src_buf->fmt->fourcc & 0xff),
+			(jpeg_src_buf->fmt->fourcc >>  8) & 0xff,
+			(jpeg_src_buf->fmt->fourcc >> 16) & 0xff,
+			(jpeg_src_buf->fmt->fourcc >> 24) & 0xff);
+
+		/*
+		 * set-up the capture queue with the pixelformat and resolution
+		 * detected from the jpeg output stream
+		 */
+		q_data_cap->w = jpeg_src_buf->w;
+		q_data_cap->h = jpeg_src_buf->h;
+		q_data_cap->fmt = jpeg_src_buf->fmt;
+		q_data_cap->w_adjusted = q_data_cap->w;
+		q_data_cap->h_adjusted = q_data_cap->h;
+
+		/*
+		 * align up the resolution for CAST IP,
+		 * but leave the buffer resolution unchanged
+		 */
+		v4l_bound_align_image(&q_data_cap->w_adjusted,
+				      q_data_cap->w_adjusted,  /* adjust up */
+				      MXC_JPEG_MAX_WIDTH,
+				      q_data_cap->fmt->h_align,
+				      &q_data_cap->h_adjusted,
+				      q_data_cap->h_adjusted, /* adjust up */
+				      MXC_JPEG_MAX_HEIGHT,
+				      0,
+				      0);
+
+		/* setup bytesperline/sizeimage for capture queue */
+		mxc_jpeg_bytesperline(q_data_cap, jpeg_src_buf->fmt->precision);
+		mxc_jpeg_sizeimage(q_data_cap);
+		notify_src_chg(ctx);
+		ctx->source_change = 1;
+	}
+	return ctx->source_change ? true : false;
+}
+
+static int mxc_jpeg_job_ready(void *priv)
+{
+	struct mxc_jpeg_ctx *ctx = priv;
+
+	return ctx->source_change ? 0 : 1;
+}
+
 static void mxc_jpeg_device_run(void *priv)
 {
 	struct mxc_jpeg_ctx *ctx = priv;
@@ -921,8 +1014,14 @@
 	v4l2_m2m_buf_copy_metadata(src_buf, dst_buf, true);
 
 	jpeg_src_buf = vb2_to_mxc_buf(&src_buf->vb2_buf);
+	if (q_data_cap->fmt->colplanes != dst_buf->vb2_buf.num_planes) {
+		dev_err(dev, "Capture format %s has %d planes, but capture buffer has %d planes\n",
+			q_data_cap->fmt->name, q_data_cap->fmt->colplanes,
+			dst_buf->vb2_buf.num_planes);
+		jpeg_src_buf->jpeg_parse_error = true;
+	}
 	if (jpeg_src_buf->jpeg_parse_error) {
-		jpeg->slot_data[ctx->slot].used = false;
+		mxc_jpeg_check_and_set_last_buffer(ctx, src_buf, dst_buf);
 		v4l2_m2m_src_buf_remove(ctx->fh.m2m_ctx);
 		v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
 		v4l2_m2m_buf_done(src_buf, VB2_BUF_STATE_ERROR);
@@ -932,6 +1031,13 @@
 
 		return;
 	}
+	if (ctx->mxc_jpeg->mode == MXC_JPEG_DECODE) {
+		if (ctx->source_change || mxc_jpeg_source_change(ctx, jpeg_src_buf)) {
+			spin_unlock_irqrestore(&ctx->mxc_jpeg->hw_lock, flags);
+			v4l2_m2m_job_finish(jpeg->m2m_dev, ctx->fh.m2m_ctx);
+			return;
+		}
+	}
 
 	/*
 	 * TODO: this reset should be removed, once we figure out
@@ -976,24 +1082,28 @@
 {
 	struct v4l2_fh *fh = file->private_data;
 	struct mxc_jpeg_ctx *ctx = mxc_jpeg_fh_to_ctx(fh);
-	struct device *dev = ctx->mxc_jpeg->dev;
 	int ret;
 
 	ret = v4l2_m2m_ioctl_try_decoder_cmd(file, fh, cmd);
 	if (ret < 0)
 		return ret;
 
-	if (cmd->cmd == V4L2_DEC_CMD_STOP) {
-		dev_dbg(dev, "Received V4L2_DEC_CMD_STOP");
-		if (v4l2_m2m_num_src_bufs_ready(fh->m2m_ctx) == 0) {
-			/* No more src bufs, notify app EOS */
-			notify_eos(ctx);
-		} else {
-			/* will send EOS later*/
-			ctx->stopping = 1;
-		}
+	if (!vb2_is_streaming(v4l2_m2m_get_src_vq(fh->m2m_ctx)))
+		return 0;
+
+	ret = v4l2_m2m_ioctl_decoder_cmd(file, priv, cmd);
+	if (ret < 0)
+		return ret;
+
+	if (cmd->cmd == V4L2_DEC_CMD_STOP &&
+	    v4l2_m2m_has_stopped(fh->m2m_ctx)) {
+		notify_eos(ctx);
+		ctx->header_parsed = false;
 	}
 
+	if (cmd->cmd == V4L2_DEC_CMD_START &&
+	    v4l2_m2m_has_stopped(fh->m2m_ctx))
+		vb2_clear_last_buffer_dequeued(&fh->m2m_ctx->cap_q_ctx.q);
 	return 0;
 }
 
@@ -1002,23 +1112,27 @@
 {
 	struct v4l2_fh *fh = file->private_data;
 	struct mxc_jpeg_ctx *ctx = mxc_jpeg_fh_to_ctx(fh);
-	struct device *dev = ctx->mxc_jpeg->dev;
 	int ret;
 
 	ret = v4l2_m2m_ioctl_try_encoder_cmd(file, fh, cmd);
 	if (ret < 0)
 		return ret;
 
-	if (cmd->cmd == V4L2_ENC_CMD_STOP) {
-		dev_dbg(dev, "Received V4L2_ENC_CMD_STOP");
-		if (v4l2_m2m_num_src_bufs_ready(fh->m2m_ctx) == 0) {
-			/* No more src bufs, notify app EOS */
-			notify_eos(ctx);
-		} else {
-			/* will send EOS later*/
-			ctx->stopping = 1;
-		}
-	}
+	if (!vb2_is_streaming(v4l2_m2m_get_src_vq(fh->m2m_ctx)) ||
+	    !vb2_is_streaming(v4l2_m2m_get_dst_vq(fh->m2m_ctx)))
+		return 0;
+
+	ret = v4l2_m2m_ioctl_encoder_cmd(file, fh, cmd);
+	if (ret < 0)
+		return 0;
+
+	if (cmd->cmd == V4L2_ENC_CMD_STOP &&
+	    v4l2_m2m_has_stopped(fh->m2m_ctx))
+		notify_eos(ctx);
+
+	if (cmd->cmd == V4L2_ENC_CMD_START &&
+	    v4l2_m2m_has_stopped(fh->m2m_ctx))
+		vb2_clear_last_buffer_dequeued(&fh->m2m_ctx->cap_q_ctx.q);
 
 	return 0;
 }
@@ -1031,16 +1145,28 @@
 {
 	struct mxc_jpeg_ctx *ctx = vb2_get_drv_priv(q);
 	struct mxc_jpeg_q_data *q_data = NULL;
+	struct mxc_jpeg_q_data tmp_q;
 	int i;
 
 	q_data = mxc_jpeg_get_q_data(ctx, q->type);
 	if (!q_data)
 		return -EINVAL;
 
+	tmp_q.fmt = q_data->fmt;
+	tmp_q.w = q_data->w_adjusted;
+	tmp_q.h = q_data->h_adjusted;
+	for (i = 0; i < MXC_JPEG_MAX_PLANES; i++) {
+		tmp_q.bytesperline[i] = q_data->bytesperline[i];
+		tmp_q.sizeimage[i] = q_data->sizeimage[i];
+	}
+	mxc_jpeg_sizeimage(&tmp_q);
+	for (i = 0; i < MXC_JPEG_MAX_PLANES; i++)
+		tmp_q.sizeimage[i] = max(tmp_q.sizeimage[i], q_data->sizeimage[i]);
+
 	/* Handle CREATE_BUFS situation - *nplanes != 0 */
 	if (*nplanes) {
 		for (i = 0; i < *nplanes; i++) {
-			if (sizes[i] < q_data->sizeimage[i])
+			if (sizes[i] < tmp_q.sizeimage[i])
 				return -EINVAL;
 		}
 		return 0;
@@ -1049,7 +1175,7 @@
 	/* Handle REQBUFS situation */
 	*nplanes = q_data->fmt->colplanes;
 	for (i = 0; i < *nplanes; i++)
-		sizes[i] = q_data->sizeimage[i];
+		sizes[i] = tmp_q.sizeimage[i];
 
 	return 0;
 }
@@ -1058,10 +1184,21 @@
 {
 	struct mxc_jpeg_ctx *ctx = vb2_get_drv_priv(q);
 	struct mxc_jpeg_q_data *q_data = mxc_jpeg_get_q_data(ctx, q->type);
+	int ret;
+
+	v4l2_m2m_update_start_streaming_state(ctx->fh.m2m_ctx, q);
 
+	if (ctx->mxc_jpeg->mode == MXC_JPEG_DECODE && V4L2_TYPE_IS_CAPTURE(q->type))
+		ctx->source_change = 0;
 	dev_dbg(ctx->mxc_jpeg->dev, "Start streaming ctx=%p", ctx);
 	q_data->sequence = 0;
 
+	ret = pm_runtime_resume_and_get(ctx->mxc_jpeg->dev);
+	if (ret < 0) {
+		dev_err(ctx->mxc_jpeg->dev, "Failed to power up jpeg\n");
+		return ret;
+	}
+
 	return 0;
 }
 
@@ -1079,9 +1216,18 @@
 		else
 			vbuf = v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
 		if (!vbuf)
-			return;
+			break;
 		v4l2_m2m_buf_done(vbuf, VB2_BUF_STATE_ERROR);
 	}
+
+	v4l2_m2m_update_stop_streaming_state(ctx->fh.m2m_ctx, q);
+	if (V4L2_TYPE_IS_OUTPUT(q->type) &&
+	    v4l2_m2m_has_stopped(ctx->fh.m2m_ctx)) {
+		notify_eos(ctx);
+		ctx->header_parsed = false;
+	}
+
+	pm_runtime_put_sync(&ctx->mxc_jpeg->pdev->dev);
 }
 
 static int mxc_jpeg_valid_comp_id(struct device *dev,
@@ -1121,14 +1267,17 @@
 
 	for (i = 0; i < MXC_JPEG_NUM_FORMATS; i++)
 		if (mxc_formats[i].subsampling == header->frame.subsampling &&
-		    mxc_formats[i].nc == header->frame.num_components) {
+		    mxc_formats[i].nc == header->frame.num_components &&
+		    mxc_formats[i].precision == header->frame.precision) {
 			fourcc = mxc_formats[i].fourcc;
 			break;
 		}
 	if (fourcc == 0) {
-		dev_err(dev, "Could not identify image format nc=%d, subsampling=%d\n",
+		dev_err(dev,
+			"Could not identify image format nc=%d, subsampling=%d, precision=%d\n",
 			header->frame.num_components,
-			header->frame.subsampling);
+			header->frame.subsampling,
+			header->frame.precision);
 		return fourcc;
 	}
 	/*
@@ -1146,26 +1295,29 @@
 	return fourcc;
 }
 
-static void mxc_jpeg_bytesperline(struct mxc_jpeg_q_data *q,
-				  u32 precision)
+static void mxc_jpeg_bytesperline(struct mxc_jpeg_q_data *q, u32 precision)
 {
 	/* Bytes distance between the leftmost pixels in two adjacent lines */
 	if (q->fmt->fourcc == V4L2_PIX_FMT_JPEG) {
 		/* bytesperline unused for compressed formats */
 		q->bytesperline[0] = 0;
 		q->bytesperline[1] = 0;
-	} else if (q->fmt->fourcc == V4L2_PIX_FMT_NV12) {
+	} else if (q->fmt->subsampling == V4L2_JPEG_CHROMA_SUBSAMPLING_420) {
 		/* When the image format is planar the bytesperline value
 		 * applies to the first plane and is divided by the same factor
 		 * as the width field for the other planes
 		 */
-		q->bytesperline[0] = q->w * (precision / 8) *
-				     (q->fmt->depth / 8);
+		q->bytesperline[0] = q->w * DIV_ROUND_UP(precision, 8);
 		q->bytesperline[1] = q->bytesperline[0];
+	} else if (q->fmt->subsampling == V4L2_JPEG_CHROMA_SUBSAMPLING_422) {
+		q->bytesperline[0] = q->w * DIV_ROUND_UP(precision, 8) * 2;
+		q->bytesperline[1] = 0;
+	} else if (q->fmt->subsampling == V4L2_JPEG_CHROMA_SUBSAMPLING_444) {
+		q->bytesperline[0] = q->w * DIV_ROUND_UP(precision, 8) * q->fmt->nc;
+		q->bytesperline[1] = 0;
 	} else {
-		/* single plane formats */
-		q->bytesperline[0] = q->w * (precision / 8) *
-				     (q->fmt->depth / 8);
+		/* grayscale */
+		q->bytesperline[0] = q->w * DIV_ROUND_UP(precision, 8);
 		q->bytesperline[1] = 0;
 	}
 }
@@ -1186,22 +1338,22 @@
 	} else {
 		q->sizeimage[0] = q->bytesperline[0] * q->h;
 		q->sizeimage[1] = 0;
-		if (q->fmt->fourcc == V4L2_PIX_FMT_NV12)
+		if (q->fmt->fourcc == V4L2_PIX_FMT_NV12M)
 			q->sizeimage[1] = q->sizeimage[0] / 2;
 	}
 }
 
-static int mxc_jpeg_parse(struct mxc_jpeg_ctx *ctx,
-			  u8 *src_addr, u32 size, bool *dht_needed)
+static int mxc_jpeg_parse(struct mxc_jpeg_ctx *ctx, struct vb2_buffer *vb)
 {
 	struct device *dev = ctx->mxc_jpeg->dev;
-	struct mxc_jpeg_q_data *q_data_out, *q_data_cap;
-	enum v4l2_buf_type cap_type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
-	bool src_chg = false;
+	struct mxc_jpeg_q_data *q_data_out;
 	u32 fourcc;
 	struct v4l2_jpeg_header header;
 	struct mxc_jpeg_sof *psof = NULL;
 	struct mxc_jpeg_sos *psos = NULL;
+	struct mxc_jpeg_src_buf *jpeg_src_buf = vb2_to_mxc_buf(vb);
+	u8 *src_addr = (u8 *)vb2_plane_vaddr(vb, 0);
+	u32 size = vb2_get_plane_payload(vb, 0);
 	int ret;
 
 	memset(&header, 0, sizeof(header));
@@ -1212,7 +1364,7 @@
 	}
 
 	/* if DHT marker present, no need to inject default one */
-	*dht_needed = (header.num_dht == 0);
+	jpeg_src_buf->dht_needed = (header.num_dht == 0);
 
 	q_data_out = mxc_jpeg_get_q_data(ctx,
 					 V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE);
@@ -1220,21 +1372,15 @@
 		dev_warn(dev, "Invalid user resolution 0x0");
 		dev_warn(dev, "Keeping resolution from JPEG: %dx%d",
 			 header.frame.width, header.frame.height);
-		q_data_out->w = header.frame.width;
-		q_data_out->h = header.frame.height;
 	} else if (header.frame.width != q_data_out->w ||
 		   header.frame.height != q_data_out->h) {
 		dev_err(dev,
 			"Resolution mismatch: %dx%d (JPEG) versus %dx%d(user)",
 			header.frame.width, header.frame.height,
 			q_data_out->w, q_data_out->h);
-		return -EINVAL;
-	}
-	if (header.frame.width % 8 != 0 || header.frame.height % 8 != 0) {
-		dev_err(dev, "JPEG width or height not multiple of 8: %dx%d\n",
-			header.frame.width, header.frame.height);
-		return -EINVAL;
 	}
+	q_data_out->w = header.frame.width;
+	q_data_out->h = header.frame.height;
 	if (header.frame.width > MXC_JPEG_MAX_WIDTH ||
 	    header.frame.height > MXC_JPEG_MAX_HEIGHT) {
 		dev_err(dev, "JPEG width or height should be <= 8192: %dx%d\n",
@@ -1262,51 +1408,13 @@
 	if (fourcc == 0)
 		return -EINVAL;
 
-	/*
-	 * set-up the capture queue with the pixelformat and resolution
-	 * detected from the jpeg output stream
-	 */
-	q_data_cap = mxc_jpeg_get_q_data(ctx, cap_type);
-	if (q_data_cap->w != header.frame.width ||
-	    q_data_cap->h != header.frame.height)
-		src_chg = true;
-	q_data_cap->w = header.frame.width;
-	q_data_cap->h = header.frame.height;
-	q_data_cap->fmt = mxc_jpeg_find_format(ctx, fourcc);
-	q_data_cap->w_adjusted = q_data_cap->w;
-	q_data_cap->h_adjusted = q_data_cap->h;
-	/*
-	 * align up the resolution for CAST IP,
-	 * but leave the buffer resolution unchanged
-	 */
-	v4l_bound_align_image(&q_data_cap->w_adjusted,
-			      q_data_cap->w_adjusted,  /* adjust up */
-			      MXC_JPEG_MAX_WIDTH,
-			      q_data_cap->fmt->h_align,
-			      &q_data_cap->h_adjusted,
-			      q_data_cap->h_adjusted, /* adjust up */
-			      MXC_JPEG_MAX_HEIGHT,
-			      q_data_cap->fmt->v_align,
-			      0);
-	dev_dbg(dev, "Detected jpeg res=(%dx%d)->(%dx%d), pixfmt=%c%c%c%c\n",
-		q_data_cap->w, q_data_cap->h,
-		q_data_cap->w_adjusted, q_data_cap->h_adjusted,
-		(fourcc & 0xff),
-		(fourcc >>  8) & 0xff,
-		(fourcc >> 16) & 0xff,
-		(fourcc >> 24) & 0xff);
-
-	/* setup bytesperline/sizeimage for capture queue */
-	mxc_jpeg_bytesperline(q_data_cap, header.frame.precision);
-	mxc_jpeg_sizeimage(q_data_cap);
+	jpeg_src_buf->fmt = mxc_jpeg_find_format(ctx, fourcc);
+	jpeg_src_buf->w = header.frame.width;
+	jpeg_src_buf->h = header.frame.height;
+	ctx->header_parsed = true;
 
-	/*
-	 * if the CAPTURE format was updated with new values, regardless of
-	 * whether they match the values set by the client or not, signal
-	 * a source change event
-	 */
-	if (src_chg)
-		notify_src_chg(ctx);
+	if (!v4l2_m2m_num_src_bufs_ready(ctx->fh.m2m_ctx))
+		mxc_jpeg_source_change(ctx, jpeg_src_buf);
 
 	return 0;
 }
@@ -1318,6 +1426,20 @@
 	struct mxc_jpeg_ctx *ctx = vb2_get_drv_priv(vb->vb2_queue);
 	struct mxc_jpeg_src_buf *jpeg_src_buf;
 
+	if (V4L2_TYPE_IS_CAPTURE(vb->vb2_queue->type) &&
+	    vb2_is_streaming(vb->vb2_queue) &&
+	    v4l2_m2m_dst_buf_is_last(ctx->fh.m2m_ctx)) {
+		struct mxc_jpeg_q_data *q_data;
+
+		q_data = mxc_jpeg_get_q_data(ctx, vb->vb2_queue->type);
+		vbuf->field = V4L2_FIELD_NONE;
+		vbuf->sequence = q_data->sequence++;
+		v4l2_m2m_last_buffer_done(ctx->fh.m2m_ctx, vbuf);
+		notify_eos(ctx);
+		ctx->header_parsed = false;
+		return;
+	}
+
 	if (vb->vb2_queue->type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
 		goto end;
 
@@ -1327,10 +1449,7 @@
 
 	jpeg_src_buf = vb2_to_mxc_buf(vb);
 	jpeg_src_buf->jpeg_parse_error = false;
-	ret = mxc_jpeg_parse(ctx,
-			     (u8 *)vb2_plane_vaddr(vb, 0),
-			     vb2_get_plane_payload(vb, 0),
-			     &jpeg_src_buf->dht_needed);
+	ret = mxc_jpeg_parse(ctx, vb);
 	if (ret)
 		jpeg_src_buf->jpeg_parse_error = true;
 
@@ -1370,6 +1489,10 @@
 		}
 		vb2_set_plane_payload(vb, i, sizeimage);
 	}
+	if (V4L2_TYPE_IS_CAPTURE(vb->vb2_queue->type)) {
+		vb2_set_plane_payload(vb, 0, 0);
+		vb2_set_plane_payload(vb, 1, 0);
+	}
 	return 0;
 }
 
@@ -1439,7 +1562,7 @@
 		q[i]->h = MXC_JPEG_DEFAULT_HEIGHT;
 		q[i]->w_adjusted = MXC_JPEG_DEFAULT_WIDTH;
 		q[i]->h_adjusted = MXC_JPEG_DEFAULT_HEIGHT;
-		mxc_jpeg_bytesperline(q[i], 8);
+		mxc_jpeg_bytesperline(q[i], q[i]->fmt->precision);
 		mxc_jpeg_sizeimage(q[i]);
 	}
 }
@@ -1514,26 +1637,42 @@
 				     struct v4l2_fmtdesc *f)
 {
 	struct mxc_jpeg_ctx *ctx = mxc_jpeg_fh_to_ctx(priv);
+	struct mxc_jpeg_q_data *q_data = mxc_jpeg_get_q_data(ctx, f->type);
 
-	if (ctx->mxc_jpeg->mode == MXC_JPEG_ENCODE)
+	if (ctx->mxc_jpeg->mode == MXC_JPEG_ENCODE) {
 		return enum_fmt(mxc_formats, MXC_JPEG_NUM_FORMATS, f,
 			MXC_JPEG_FMT_TYPE_ENC);
-	else
+	} else if (!ctx->header_parsed) {
 		return enum_fmt(mxc_formats, MXC_JPEG_NUM_FORMATS, f,
 			MXC_JPEG_FMT_TYPE_RAW);
+	} else {
+		/* For the decoder CAPTURE queue, only enumerate the raw formats
+		 * supported for the format currently active on OUTPUT
+		 * (more precisely what was propagated on capture queue
+		 * after jpeg parse on the output buffer)
+		 */
+		if (f->index)
+			return -EINVAL;
+		f->pixelformat = q_data->fmt->fourcc;
+		strscpy(f->description, q_data->fmt->name, sizeof(f->description));
+		return 0;
+	}
 }
 
 static int mxc_jpeg_enum_fmt_vid_out(struct file *file, void *priv,
 				     struct v4l2_fmtdesc *f)
 {
 	struct mxc_jpeg_ctx *ctx = mxc_jpeg_fh_to_ctx(priv);
+	u32 type = ctx->mxc_jpeg->mode == MXC_JPEG_DECODE ?  MXC_JPEG_FMT_TYPE_ENC :
+							     MXC_JPEG_FMT_TYPE_RAW;
+	int ret;
 
+	ret = enum_fmt(mxc_formats, MXC_JPEG_NUM_FORMATS, f, type);
+	if (ret)
+		return ret;
 	if (ctx->mxc_jpeg->mode == MXC_JPEG_DECODE)
-		return enum_fmt(mxc_formats, MXC_JPEG_NUM_FORMATS, f,
-				MXC_JPEG_FMT_TYPE_ENC);
-	else
-		return enum_fmt(mxc_formats, MXC_JPEG_NUM_FORMATS, f,
-				MXC_JPEG_FMT_TYPE_RAW);
+		f->flags = V4L2_FMT_FLAG_DYN_RESOLUTION;
+	return 0;
 }
 
 static int mxc_jpeg_try_fmt(struct v4l2_format *f, const struct mxc_jpeg_fmt *fmt,
@@ -1553,22 +1692,17 @@
 	pix_mp->num_planes = fmt->colplanes;
 	pix_mp->pixelformat = fmt->fourcc;
 
-	/*
-	 * use MXC_JPEG_H_ALIGN instead of fmt->v_align, for vertical
-	 * alignment, to loosen up the alignment to multiple of 8,
-	 * otherwise NV12-1080p fails as 1080 is not a multiple of 16
-	 */
+	pix_mp->width = w;
+	pix_mp->height = h;
 	v4l_bound_align_image(&w,
-			      MXC_JPEG_MIN_WIDTH,
-			      w, /* adjust downwards*/
+			      w, /* adjust upwards*/
+			      MXC_JPEG_MAX_WIDTH,
 			      fmt->h_align,
 			      &h,
-			      MXC_JPEG_MIN_HEIGHT,
-			      h, /* adjust downwards*/
-			      MXC_JPEG_H_ALIGN,
+			      h, /* adjust upwards*/
+			      MXC_JPEG_MAX_HEIGHT,
+			      0,
 			      0);
-	pix_mp->width = w; /* negotiate the width */
-	pix_mp->height = h; /* negotiate the height */
 
 	/* get user input into the tmp_q */
 	tmp_q.w = w;
@@ -1581,7 +1715,7 @@
 	}
 
 	/* calculate bytesperline & sizeimage into the tmp_q */
-	mxc_jpeg_bytesperline(&tmp_q, 8);
+	mxc_jpeg_bytesperline(&tmp_q, fmt->precision);
 	mxc_jpeg_sizeimage(&tmp_q);
 
 	/* adjust user format according to our calculations */
@@ -1694,35 +1828,19 @@
 
 	q_data->w_adjusted = q_data->w;
 	q_data->h_adjusted = q_data->h;
-	if (jpeg->mode == MXC_JPEG_DECODE) {
-		/*
-		 * align up the resolution for CAST IP,
-		 * but leave the buffer resolution unchanged
-		 */
-		v4l_bound_align_image(&q_data->w_adjusted,
-				      q_data->w_adjusted,  /* adjust upwards */
-				      MXC_JPEG_MAX_WIDTH,
-				      q_data->fmt->h_align,
-				      &q_data->h_adjusted,
-				      q_data->h_adjusted, /* adjust upwards */
-				      MXC_JPEG_MAX_HEIGHT,
-				      q_data->fmt->v_align,
-				      0);
-	} else {
-		/*
-		 * align down the resolution for CAST IP,
-		 * but leave the buffer resolution unchanged
-		 */
-		v4l_bound_align_image(&q_data->w_adjusted,
-				      MXC_JPEG_MIN_WIDTH,
-				      q_data->w_adjusted, /* adjust downwards*/
-				      q_data->fmt->h_align,
-				      &q_data->h_adjusted,
-				      MXC_JPEG_MIN_HEIGHT,
-				      q_data->h_adjusted, /* adjust downwards*/
-				      q_data->fmt->v_align,
-				      0);
-	}
+	/*
+	 * align up the resolution for CAST IP,
+	 * but leave the buffer resolution unchanged
+	 */
+	v4l_bound_align_image(&q_data->w_adjusted,
+			      q_data->w_adjusted,  /* adjust upwards */
+			      MXC_JPEG_MAX_WIDTH,
+			      q_data->fmt->h_align,
+			      &q_data->h_adjusted,
+			      q_data->h_adjusted, /* adjust upwards */
+			      MXC_JPEG_MAX_HEIGHT,
+			      q_data->fmt->v_align,
+			      0);
 
 	for (i = 0; i < pix_mp->num_planes; i++) {
 		q_data->bytesperline[i] = pix_mp->plane_fmt[i].bytesperline;
@@ -1804,27 +1922,6 @@
 	}
 }
 
-static int mxc_jpeg_dqbuf(struct file *file, void *priv,
-			  struct v4l2_buffer *buf)
-{
-	struct v4l2_fh *fh = file->private_data;
-	struct mxc_jpeg_ctx *ctx = mxc_jpeg_fh_to_ctx(priv);
-	struct device *dev = ctx->mxc_jpeg->dev;
-	int num_src_ready = v4l2_m2m_num_src_bufs_ready(fh->m2m_ctx);
-	int ret;
-
-	dev_dbg(dev, "DQBUF type=%d, index=%d", buf->type, buf->index);
-	if (ctx->stopping == 1	&& num_src_ready == 0) {
-		/* No more src bufs, notify app EOS */
-		notify_eos(ctx);
-		ctx->stopping = 0;
-	}
-
-	ret = v4l2_m2m_dqbuf(file, fh->m2m_ctx, buf);
-
-	return ret;
-}
-
 static const struct v4l2_ioctl_ops mxc_jpeg_ioctl_ops = {
 	.vidioc_querycap		= mxc_jpeg_querycap,
 	.vidioc_enum_fmt_vid_cap	= mxc_jpeg_enum_fmt_vid_cap,
@@ -1848,7 +1945,7 @@
 	.vidioc_encoder_cmd		= mxc_jpeg_encoder_cmd,
 
 	.vidioc_qbuf			= v4l2_m2m_ioctl_qbuf,
-	.vidioc_dqbuf			= mxc_jpeg_dqbuf,
+	.vidioc_dqbuf			= v4l2_m2m_ioctl_dqbuf,
 
 	.vidioc_create_bufs		= v4l2_m2m_ioctl_create_bufs,
 	.vidioc_prepare_buf		= v4l2_m2m_ioctl_prepare_buf,
@@ -1891,6 +1988,7 @@
 };
 
 static const struct v4l2_m2m_ops mxc_jpeg_m2m_ops = {
+	.job_ready      = mxc_jpeg_job_ready,
 	.device_run	= mxc_jpeg_device_run,
 };
 
@@ -1899,9 +1997,12 @@
 	int i;
 
 	for (i = 0; i < jpeg->num_domains; i++) {
-		if (jpeg->pd_link[i] && !IS_ERR(jpeg->pd_link[i]))
+		if (!IS_ERR_OR_NULL(jpeg->pd_dev[i]) &&
+		    !pm_runtime_suspended(jpeg->pd_dev[i]))
+			pm_runtime_force_suspend(jpeg->pd_dev[i]);
+		if (!IS_ERR_OR_NULL(jpeg->pd_link[i]))
 			device_link_del(jpeg->pd_link[i]);
-		if (jpeg->pd_dev[i] && !IS_ERR(jpeg->pd_dev[i]))
+		if (!IS_ERR_OR_NULL(jpeg->pd_dev[i]))
 			dev_pm_domain_detach(jpeg->pd_dev[i], true);
 		jpeg->pd_dev[i] = NULL;
 		jpeg->pd_link[i] = NULL;
@@ -1941,8 +2042,7 @@
 
 		jpeg->pd_link[i] = device_link_add(dev, jpeg->pd_dev[i],
 						   DL_FLAG_STATELESS |
-						   DL_FLAG_PM_RUNTIME |
-						   DL_FLAG_RPM_ACTIVE);
+						   DL_FLAG_PM_RUNTIME);
 		if (!jpeg->pd_link[i]) {
 			ret = -EINVAL;
 			goto fail;
@@ -2007,6 +2107,14 @@
 	jpeg->dev = dev;
 	jpeg->mode = mode;
 
+	/* Get clocks */
+	ret = devm_clk_bulk_get_all(&pdev->dev, &jpeg->clks);
+	if (ret < 0) {
+		dev_err(dev, "failed to get clock\n");
+		goto err_clk;
+	}
+	jpeg->num_clks = ret;
+
 	ret = mxc_jpeg_attach_pm_domains(jpeg);
 	if (ret < 0) {
 		dev_err(dev, "failed to attach power domains %d\n", ret);
@@ -2050,6 +2158,7 @@
 	jpeg->dec_vdev->vfl_dir = VFL_DIR_M2M;
 	jpeg->dec_vdev->device_caps = V4L2_CAP_STREAMING |
 					V4L2_CAP_VIDEO_M2M_MPLANE;
+	video_set_drvdata(jpeg->dec_vdev, jpeg);
 	if (mode == MXC_JPEG_ENCODE) {
 		v4l2_disable_ioctl(jpeg->dec_vdev, VIDIOC_DECODER_CMD);
 		v4l2_disable_ioctl(jpeg->dec_vdev, VIDIOC_TRY_DECODER_CMD);
@@ -2062,7 +2171,6 @@
 		dev_err(dev, "failed to register video device\n");
 		goto err_vdev_register;
 	}
-	video_set_drvdata(jpeg->dec_vdev, jpeg);
 	if (mode == MXC_JPEG_ENCODE)
 		v4l2_info(&jpeg->v4l2_dev,
 			  "encoder device registered as /dev/video%d (%d,%d)\n",
@@ -2075,6 +2183,7 @@
 			  jpeg->dec_vdev->minor);
 
 	platform_set_drvdata(pdev, jpeg);
+	pm_runtime_enable(dev);
 
 	return 0;
 
@@ -2088,10 +2197,43 @@
 	v4l2_device_unregister(&jpeg->v4l2_dev);
 
 err_register:
+	mxc_jpeg_detach_pm_domains(jpeg);
+
 err_irq:
+err_clk:
 	return ret;
 }
 
+#ifdef CONFIG_PM
+static int mxc_jpeg_runtime_resume(struct device *dev)
+{
+	struct mxc_jpeg_dev *jpeg = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_bulk_prepare_enable(jpeg->num_clks, jpeg->clks);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable clock\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int mxc_jpeg_runtime_suspend(struct device *dev)
+{
+	struct mxc_jpeg_dev *jpeg = dev_get_drvdata(dev);
+
+	clk_bulk_disable_unprepare(jpeg->num_clks, jpeg->clks);
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops	mxc_jpeg_pm_ops = {
+	SET_RUNTIME_PM_OPS(mxc_jpeg_runtime_suspend,
+			   mxc_jpeg_runtime_resume, NULL)
+};
+
 static int mxc_jpeg_remove(struct platform_device *pdev)
 {
 	unsigned int slot;
@@ -2100,6 +2242,7 @@
 	for (slot = 0; slot < MXC_MAX_SLOTS; slot++)
 		mxc_jpeg_free_slot_data(jpeg, slot);
 
+	pm_runtime_disable(&pdev->dev);
 	video_unregister_device(jpeg->dec_vdev);
 	v4l2_m2m_release(jpeg->m2m_dev);
 	v4l2_device_unregister(&jpeg->v4l2_dev);
@@ -2116,6 +2259,7 @@
 	.driver = {
 		.name = "mxc-jpeg",
 		.of_match_table = mxc_jpeg_match,
+		.pm = &mxc_jpeg_pm_ops,
 	},
 };
 module_platform_driver(mxc_jpeg_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/imx-jpeg/mxc-jpeg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/imx-jpeg/mxc-jpeg.h
@@ -49,6 +49,7 @@
  * @h_align:	horizontal alignment order (align to 2^h_align)
  * @v_align:	vertical alignment order (align to 2^v_align)
  * @flags:	flags describing format applicability
+ * @precision:  jpeg sample precision
  */
 struct mxc_jpeg_fmt {
 	const char				*name;
@@ -60,6 +61,7 @@
 	int					h_align;
 	int					v_align;
 	u32					flags;
+	u8					precision;
 };
 
 struct mxc_jpeg_desc {
@@ -90,8 +92,9 @@
 	struct mxc_jpeg_q_data		cap_q;
 	struct v4l2_fh			fh;
 	enum mxc_jpeg_enc_state		enc_state;
-	unsigned int			stopping;
 	unsigned int			slot;
+	unsigned int			source_change;
+	bool				header_parsed;
 };
 
 struct mxc_jpeg_slot_data {
@@ -109,6 +112,8 @@
 	spinlock_t			hw_lock; /* hardware access lock */
 	unsigned int			mode;
 	struct mutex			lock; /* v4l2 ioctls serialization */
+	struct clk_bulk_data		*clks;
+	int				num_clks;
 	struct platform_device		*pdev;
 	struct device			*dev;
 	void __iomem			*base_reg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/imx-pxp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/imx-pxp.c
@@ -1661,6 +1661,8 @@
 	if (irq < 0)
 		return irq;
 
+	spin_lock_init(&dev->irqlock);
+
 	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, pxp_irq_handler,
 			IRQF_ONESHOT, dev_name(&pdev->dev), dev);
 	if (ret < 0) {
@@ -1678,8 +1680,6 @@
 		goto err_clk;
 	}
 
-	spin_lock_init(&dev->irqlock);
-
 	ret = v4l2_device_register(&pdev->dev, &dev->v4l2_dev);
 	if (ret)
 		goto err_clk;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/marvell-ccic/mcam-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/marvell-ccic/mcam-core.c
@@ -935,7 +935,12 @@
 	ret = pm_runtime_resume_and_get(cam->dev);
 	if (ret < 0)
 		return ret;
-	clk_enable(cam->clk[0]);
+	ret = clk_enable(cam->clk[0]);
+	if (ret) {
+		pm_runtime_put(cam->dev);
+		return ret;
+	}
+
 	mcam_reg_write(cam, REG_CLKCTRL, (mclk_src << 29) | mclk_div);
 	mcam_ctlr_power_up(cam);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/meson/ge2d/ge2d.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/meson/ge2d/ge2d.c
@@ -215,35 +215,35 @@
 
 	regmap_write(ge2d->map, GE2D_SRC1_CLIPY_START_END,
 		     FIELD_PREP(GE2D_START, ctx->in.crop.top) |
-		     FIELD_PREP(GE2D_END, ctx->in.crop.top + ctx->in.crop.height));
+		     FIELD_PREP(GE2D_END, ctx->in.crop.top + ctx->in.crop.height - 1));
 	regmap_write(ge2d->map, GE2D_SRC1_CLIPX_START_END,
 		     FIELD_PREP(GE2D_START, ctx->in.crop.left) |
-		     FIELD_PREP(GE2D_END, ctx->in.crop.left + ctx->in.crop.width));
+		     FIELD_PREP(GE2D_END, ctx->in.crop.left + ctx->in.crop.width - 1));
 	regmap_write(ge2d->map, GE2D_SRC2_CLIPY_START_END,
 		     FIELD_PREP(GE2D_START, ctx->out.crop.top) |
-		     FIELD_PREP(GE2D_END, ctx->out.crop.top + ctx->out.crop.height));
+		     FIELD_PREP(GE2D_END, ctx->out.crop.top + ctx->out.crop.height - 1));
 	regmap_write(ge2d->map, GE2D_SRC2_CLIPX_START_END,
 		     FIELD_PREP(GE2D_START, ctx->out.crop.left) |
-		     FIELD_PREP(GE2D_END, ctx->out.crop.left + ctx->out.crop.width));
+		     FIELD_PREP(GE2D_END, ctx->out.crop.left + ctx->out.crop.width - 1));
 	regmap_write(ge2d->map, GE2D_DST_CLIPY_START_END,
 		     FIELD_PREP(GE2D_START, ctx->out.crop.top) |
-		     FIELD_PREP(GE2D_END, ctx->out.crop.top + ctx->out.crop.height));
+		     FIELD_PREP(GE2D_END, ctx->out.crop.top + ctx->out.crop.height - 1));
 	regmap_write(ge2d->map, GE2D_DST_CLIPX_START_END,
 		     FIELD_PREP(GE2D_START, ctx->out.crop.left) |
-		     FIELD_PREP(GE2D_END, ctx->out.crop.left + ctx->out.crop.width));
+		     FIELD_PREP(GE2D_END, ctx->out.crop.left + ctx->out.crop.width - 1));
 
 	regmap_write(ge2d->map, GE2D_SRC1_Y_START_END,
-		     FIELD_PREP(GE2D_END, ctx->in.pix_fmt.height));
+		     FIELD_PREP(GE2D_END, ctx->in.pix_fmt.height - 1));
 	regmap_write(ge2d->map, GE2D_SRC1_X_START_END,
-		     FIELD_PREP(GE2D_END, ctx->in.pix_fmt.width));
+		     FIELD_PREP(GE2D_END, ctx->in.pix_fmt.width - 1));
 	regmap_write(ge2d->map, GE2D_SRC2_Y_START_END,
-		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.height));
+		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.height - 1));
 	regmap_write(ge2d->map, GE2D_SRC2_X_START_END,
-		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.width));
+		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.width - 1));
 	regmap_write(ge2d->map, GE2D_DST_Y_START_END,
-		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.height));
+		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.height - 1));
 	regmap_write(ge2d->map, GE2D_DST_X_START_END,
-		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.width));
+		     FIELD_PREP(GE2D_END, ctx->out.pix_fmt.width - 1));
 
 	/* Color, no blend, use source color */
 	reg = GE2D_ALU_DO_COLOR_OPERATION_LOGIC(LOGIC_OPERATION_COPY,
@@ -779,11 +779,7 @@
 		 * If the rotation parameter changes the OUTPUT frames
 		 * parameters, take them in account
 		 */
-		if (fmt.width != ctx->out.pix_fmt.width ||
-		    fmt.height != ctx->out.pix_fmt.width ||
-		    fmt.bytesperline > ctx->out.pix_fmt.bytesperline ||
-		    fmt.sizeimage > ctx->out.pix_fmt.sizeimage)
-			ctx->out.pix_fmt = fmt;
+		ctx->out.pix_fmt = fmt;
 
 		break;
 	}
@@ -1036,7 +1032,6 @@
 
 	video_unregister_device(ge2d->vfd);
 	v4l2_m2m_release(ge2d->m2m_dev);
-	video_device_release(ge2d->vfd);
 	v4l2_device_unregister(&ge2d->v4l2_dev);
 	clk_disable_unprepare(ge2d->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c
@@ -977,13 +977,13 @@
 	if (ret < 0)
 		goto dec_end;
 
-	schedule_delayed_work(&jpeg->job_timeout_work,
-			      msecs_to_jiffies(MTK_JPEG_HW_TIMEOUT_MSEC));
-
 	mtk_jpeg_set_dec_src(ctx, &src_buf->vb2_buf, &bs);
 	if (mtk_jpeg_set_dec_dst(ctx, &jpeg_src_buf->dec_param, &dst_buf->vb2_buf, &fb))
 		goto dec_end;
 
+	schedule_delayed_work(&jpeg->job_timeout_work,
+			      msecs_to_jiffies(MTK_JPEG_HW_TIMEOUT_MSEC));
+
 	spin_lock_irqsave(&jpeg->hw_lock, flags);
 	mtk_jpeg_dec_reset(jpeg->reg_base);
 	mtk_jpeg_dec_set_config(jpeg->reg_base,
@@ -1455,9 +1455,9 @@
 {
 	struct mtk_jpeg_dev *jpeg = platform_get_drvdata(pdev);
 
+	cancel_delayed_work_sync(&jpeg->job_timeout_work);
 	pm_runtime_disable(&pdev->dev);
 	video_unregister_device(jpeg->vdev);
-	video_device_release(jpeg->vdev);
 	v4l2_m2m_release(jpeg->m2m_dev);
 	v4l2_device_unregister(&jpeg->v4l2_dev);
 	mtk_jpeg_clk_release(jpeg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-mdp/mtk_mdp_ipi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-mdp/mtk_mdp_ipi.h
@@ -40,12 +40,14 @@
  * @ipi_id        : IPI_MDP
  * @ap_inst       : AP mtk_mdp_vpu address
  * @vpu_inst_addr : VPU MDP instance address
+ * @padding       : Alignment padding
  */
 struct mdp_ipi_comm {
 	uint32_t msg_id;
 	uint32_t ipi_id;
 	uint64_t ap_inst;
 	uint32_t vpu_inst_addr;
+	uint32_t padding;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-mdp/mtk_mdp_vpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-mdp/mtk_mdp_vpu.c
@@ -26,7 +26,7 @@
 	vpu->inst_addr = msg->vpu_inst_addr;
 }
 
-static void mtk_mdp_vpu_ipi_handler(const void *data, unsigned int len,
+static void mtk_mdp_vpu_ipi_handler(void *data, unsigned int len,
 				    void *priv)
 {
 	const struct mdp_ipi_comm_ack *msg = data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc.c
@@ -733,6 +733,8 @@
 		return -EINVAL;
 
 	if (*nplanes) {
+		if (*nplanes != q_data->fmt->num_planes)
+			return -EINVAL;
 		for (i = 0; i < *nplanes; i++)
 			if (sizes[i] < q_data->sizeimage[i])
 				return -EINVAL;
@@ -793,7 +795,7 @@
 {
 	struct mtk_vcodec_ctx *ctx = vb2_get_drv_priv(q);
 	struct venc_enc_param param;
-	int ret;
+	int ret, pm_ret;
 	int i;
 
 	/* Once state turn into MTK_STATE_ABORT, we need stop_streaming
@@ -845,9 +847,9 @@
 	return 0;
 
 err_set_param:
-	ret = pm_runtime_put(&ctx->dev->plat_dev->dev);
-	if (ret < 0)
-		mtk_v4l2_err("pm_runtime_put fail %d", ret);
+	pm_ret = pm_runtime_put(&ctx->dev->plat_dev->dev);
+	if (pm_ret < 0)
+		mtk_v4l2_err("pm_runtime_put fail %d", pm_ret);
 
 err_start_stream:
 	for (i = 0; i < q->num_buffers; ++i) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_drv.c
@@ -218,11 +218,11 @@
 	mtk_v4l2_debug(1, "[%d] encoder", ctx->id);
 	mutex_lock(&dev->dev_mutex);
 
+	v4l2_m2m_ctx_release(ctx->m2m_ctx);
 	mtk_vcodec_enc_release(ctx);
 	v4l2_fh_del(&ctx->fh);
 	v4l2_fh_exit(&ctx->fh);
 	v4l2_ctrl_handler_free(&ctx->ctrl_hdl);
-	v4l2_m2m_ctx_release(ctx->m2m_ctx);
 
 	list_del_init(&ctx->list);
 	kfree(ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vcodec/mtk_vcodec_fw_scp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vcodec/mtk_vcodec_fw_scp.c
@@ -65,6 +65,8 @@
 	}
 
 	fw = devm_kzalloc(&dev->plat_dev->dev, sizeof(*fw), GFP_KERNEL);
+	if (!fw)
+		return ERR_PTR(-ENOMEM);
 	fw->type = SCP;
 	fw->ops = &mtk_vcodec_rproc_msg;
 	fw->scp = scp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vcodec/mtk_vcodec_fw_vpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vcodec/mtk_vcodec_fw_vpu.c
@@ -29,15 +29,7 @@
 					   mtk_vcodec_ipi_handler handler,
 					   const char *name, void *priv)
 {
-	/*
-	 * The handler we receive takes a void * as its first argument. We
-	 * cannot change this because it needs to be passed down to the rproc
-	 * subsystem when SCP is used. VPU takes a const argument, which is
-	 * more constrained, so the conversion below is safe.
-	 */
-	ipi_handler_t handler_const = (ipi_handler_t)handler;
-
-	return vpu_ipi_register(fw->pdev, id, handler_const, name, priv);
+	return vpu_ipi_register(fw->pdev, id, handler, name, priv);
 }
 
 static int mtk_vcodec_vpu_ipi_send(struct mtk_vcodec_fw *fw, int id, void *buf,
@@ -102,6 +94,8 @@
 	vpu_wdt_reg_handler(fw_pdev, mtk_vcodec_vpu_reset_handler, dev, rst_id);
 
 	fw = devm_kzalloc(&dev->plat_dev->dev, sizeof(*fw), GFP_KERNEL);
+	if (!fw)
+		return ERR_PTR(-ENOMEM);
 	fw->type = VPU;
 	fw->ops = &mtk_vcodec_vpu_msg;
 	fw->pdev = fw_pdev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c
@@ -226,10 +226,11 @@
 		if (fb->base_y.va == addr) {
 			list_move_tail(&node->list,
 				       &inst->available_fb_node_list);
-			break;
+			return fb;
 		}
 	}
-	return fb;
+
+	return NULL;
 }
 
 static void vp9_add_to_fb_free_list(struct vdec_vp9_inst *inst,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vpu/mtk_vpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vpu/mtk_vpu.c
@@ -562,15 +562,17 @@
 int vpu_load_firmware(struct platform_device *pdev)
 {
 	struct mtk_vpu *vpu;
-	struct device *dev = &pdev->dev;
+	struct device *dev;
 	struct vpu_run *run;
 	int ret;
 
 	if (!pdev) {
-		dev_err(dev, "VPU platform device is invalid\n");
+		pr_err("VPU platform device is invalid\n");
 		return -EINVAL;
 	}
 
+	dev = &pdev->dev;
+
 	vpu = platform_get_drvdata(pdev);
 	run = &vpu->run;
 
@@ -633,7 +635,7 @@
 }
 EXPORT_SYMBOL_GPL(vpu_load_firmware);
 
-static void vpu_init_ipi_handler(const void *data, unsigned int len, void *priv)
+static void vpu_init_ipi_handler(void *data, unsigned int len, void *priv)
 {
 	struct mtk_vpu *vpu = priv;
 	const struct vpu_run *run = data;
@@ -848,7 +850,8 @@
 	vpu->wdt.wq = create_singlethread_workqueue("vpu_wdt");
 	if (!vpu->wdt.wq) {
 		dev_err(dev, "initialize wdt workqueue failed\n");
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto clk_unprepare;
 	}
 	INIT_WORK(&vpu->wdt.ws, vpu_wdt_reset_func);
 	mutex_init(&vpu->vpu_mutex);
@@ -942,6 +945,8 @@
 	vpu_clock_disable(vpu);
 workqueue_destroy:
 	destroy_workqueue(vpu->wdt.wq);
+clk_unprepare:
+	clk_unprepare(vpu->clk);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/mtk-vpu/mtk_vpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/mtk-vpu/mtk_vpu.h
@@ -17,7 +17,7 @@
  * VPU interfaces with other blocks by share memory and interrupt.
  */
 
-typedef void (*ipi_handler_t) (const void *data,
+typedef void (*ipi_handler_t) (void *data,
 			       unsigned int len,
 			       void *priv);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/omap3isp/isp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/omap3isp/isp.c
@@ -2306,7 +2306,16 @@
 
 	/* Regulators */
 	isp->isp_csiphy1.vdd = devm_regulator_get(&pdev->dev, "vdd-csiphy1");
+	if (IS_ERR(isp->isp_csiphy1.vdd)) {
+		ret = PTR_ERR(isp->isp_csiphy1.vdd);
+		goto error;
+	}
+
 	isp->isp_csiphy2.vdd = devm_regulator_get(&pdev->dev, "vdd-csiphy2");
+	if (IS_ERR(isp->isp_csiphy2.vdd)) {
+		ret = PTR_ERR(isp->isp_csiphy2.vdd);
+		goto error;
+	}
 
 	/* Clocks
 	 *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/omap3isp/ispstat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/omap3isp/ispstat.c
@@ -512,7 +512,7 @@
 int omap3isp_stat_request_statistics_time32(struct ispstat *stat,
 					struct omap3isp_stat_data_time32 *data)
 {
-	struct omap3isp_stat_data data64;
+	struct omap3isp_stat_data data64 = { };
 	int ret;
 
 	ret = omap3isp_stat_request_statistics(stat, &data64);
@@ -521,7 +521,8 @@
 
 	data->ts.tv_sec = data64.ts.tv_sec;
 	data->ts.tv_usec = data64.ts.tv_usec;
-	memcpy(&data->buf, &data64.buf, sizeof(*data) - sizeof(data->ts));
+	data->buf = (uintptr_t)data64.buf;
+	memcpy(&data->frame, &data64.frame, sizeof(data->frame));
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss-csid-170.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss-csid-170.c
@@ -105,7 +105,8 @@
 #define CSID_RDI_CTRL(rdi)			((IS_LITE ? 0x208 : 0x308)\
 						+ 0x100 * (rdi))
 #define		RDI_CTRL_HALT_CMD		0
-#define			ALT_CMD_RESUME_AT_FRAME_BOUNDARY	1
+#define			HALT_CMD_HALT_AT_FRAME_BOUNDARY		0
+#define			HALT_CMD_RESUME_AT_FRAME_BOUNDARY	1
 #define		RDI_CTRL_HALT_MODE		2
 
 #define CSID_RDI_FRM_DROP_PATTERN(rdi)			((IS_LITE ? 0x20C : 0x30C)\
@@ -326,13 +327,14 @@
 	},
 };
 
-static void csid_configure_stream(struct csid_device *csid, u8 enable)
+static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)
 {
 	struct csid_testgen_config *tg = &csid->testgen;
 	u32 val;
 	u32 phy_sel = 0;
 	u8 lane_cnt = csid->phy.lane_cnt;
-	struct v4l2_mbus_framefmt *input_format = &csid->fmt[MSM_CSID_PAD_SRC];
+	/* Source pads matching RDI channels on hardware. Pad 1 -> RDI0, Pad 2 -> RDI1, etc. */
+	struct v4l2_mbus_framefmt *input_format = &csid->fmt[MSM_CSID_PAD_FIRST_SRC + vc];
 	const struct csid_format *format = csid_get_fmt_entry(csid->formats, csid->nformats,
 							      input_format->code);
 
@@ -343,13 +345,9 @@
 		phy_sel = csid->phy.csiphy_id;
 
 	if (enable) {
-		u8 vc = 0; /* Virtual Channel 0 */
-		u8 dt_id = vc * 4;
+		u8 dt_id = vc;
 
 		if (tg->enabled) {
-			/* Config Test Generator */
-			vc = 0xa;
-
 			/* configure one DT, infinite frames */
 			val = vc << TPG_VC_CFG0_VC_NUM;
 			val |= INTELEAVING_MODE_ONE_SHOT << TPG_VC_CFG0_LINE_INTERLEAVING_MODE;
@@ -362,14 +360,14 @@
 
 			writel_relaxed(0x12345678, csid->base + CSID_TPG_LFSR_SEED);
 
-			val = input_format->height & 0x1fff << TPG_DT_n_CFG_0_FRAME_HEIGHT;
-			val |= input_format->width & 0x1fff << TPG_DT_n_CFG_0_FRAME_WIDTH;
+			val = (input_format->height & 0x1fff) << TPG_DT_n_CFG_0_FRAME_HEIGHT;
+			val |= (input_format->width & 0x1fff) << TPG_DT_n_CFG_0_FRAME_WIDTH;
 			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_0(0));
 
-			val = DATA_TYPE_RAW_10BIT << TPG_DT_n_CFG_1_DATA_TYPE;
+			val = format->data_type << TPG_DT_n_CFG_1_DATA_TYPE;
 			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_1(0));
 
-			val = tg->mode << TPG_DT_n_CFG_2_PAYLOAD_MODE;
+			val = (tg->mode - 1) << TPG_DT_n_CFG_2_PAYLOAD_MODE;
 			val |= 0xBE << TPG_DT_n_CFG_2_USER_SPECIFIED_PAYLOAD;
 			val |= format->decode_format << TPG_DT_n_CFG_2_ENCODE_FORMAT;
 			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_2(0));
@@ -382,46 +380,47 @@
 		val = 1 << RDI_CFG0_BYTE_CNTR_EN;
 		val |= 1 << RDI_CFG0_FORMAT_MEASURE_EN;
 		val |= 1 << RDI_CFG0_TIMESTAMP_EN;
+		/* note: for non-RDI path, this should be format->decode_format */
 		val |= DECODE_FORMAT_PAYLOAD_ONLY << RDI_CFG0_DECODE_FORMAT;
-		val |= DATA_TYPE_RAW_10BIT << RDI_CFG0_DATA_TYPE;
+		val |= format->data_type << RDI_CFG0_DATA_TYPE;
 		val |= vc << RDI_CFG0_VIRTUAL_CHANNEL;
 		val |= dt_id << RDI_CFG0_DT_ID;
-		writel_relaxed(val, csid->base + CSID_RDI_CFG0(0));
+		writel_relaxed(val, csid->base + CSID_RDI_CFG0(vc));
 
 		/* CSID_TIMESTAMP_STB_POST_IRQ */
 		val = 2 << RDI_CFG1_TIMESTAMP_STB_SEL;
-		writel_relaxed(val, csid->base + CSID_RDI_CFG1(0));
+		writel_relaxed(val, csid->base + CSID_RDI_CFG1(vc));
 
 		val = 1;
-		writel_relaxed(val, csid->base + CSID_RDI_FRM_DROP_PERIOD(0));
+		writel_relaxed(val, csid->base + CSID_RDI_FRM_DROP_PERIOD(vc));
 
 		val = 0;
-		writel_relaxed(0, csid->base + CSID_RDI_FRM_DROP_PATTERN(0));
+		writel_relaxed(val, csid->base + CSID_RDI_FRM_DROP_PATTERN(vc));
 
 		val = 1;
-		writel_relaxed(val, csid->base + CSID_RDI_IRQ_SUBSAMPLE_PERIOD(0));
+		writel_relaxed(val, csid->base + CSID_RDI_IRQ_SUBSAMPLE_PERIOD(vc));
 
 		val = 0;
-		writel_relaxed(val, csid->base + CSID_RDI_IRQ_SUBSAMPLE_PATTERN(0));
+		writel_relaxed(val, csid->base + CSID_RDI_IRQ_SUBSAMPLE_PATTERN(vc));
 
 		val = 1;
-		writel_relaxed(val, csid->base + CSID_RDI_RPP_PIX_DROP_PERIOD(0));
+		writel_relaxed(val, csid->base + CSID_RDI_RPP_PIX_DROP_PERIOD(vc));
 
 		val = 0;
-		writel_relaxed(val, csid->base + CSID_RDI_RPP_PIX_DROP_PATTERN(0));
+		writel_relaxed(val, csid->base + CSID_RDI_RPP_PIX_DROP_PATTERN(vc));
 
 		val = 1;
-		writel_relaxed(val, csid->base + CSID_RDI_RPP_LINE_DROP_PERIOD(0));
+		writel_relaxed(val, csid->base + CSID_RDI_RPP_LINE_DROP_PERIOD(vc));
 
 		val = 0;
-		writel_relaxed(val, csid->base + CSID_RDI_RPP_LINE_DROP_PATTERN(0));
+		writel_relaxed(val, csid->base + CSID_RDI_RPP_LINE_DROP_PATTERN(vc));
 
 		val = 0;
-		writel_relaxed(val, csid->base + CSID_RDI_CTRL(0));
+		writel_relaxed(val, csid->base + CSID_RDI_CTRL(vc));
 
-		val = readl_relaxed(csid->base + CSID_RDI_CFG0(0));
+		val = readl_relaxed(csid->base + CSID_RDI_CFG0(vc));
 		val |=  1 << RDI_CFG0_ENABLE;
-		writel_relaxed(val, csid->base + CSID_RDI_CFG0(0));
+		writel_relaxed(val, csid->base + CSID_RDI_CFG0(vc));
 	}
 
 	if (tg->enabled) {
@@ -440,17 +439,25 @@
 	writel_relaxed(val, csid->base + CSID_CSI2_RX_CFG0);
 
 	val = 1 << CSI2_RX_CFG1_PACKET_ECC_CORRECTION_EN;
+	if (vc > 3)
+		val |= 1 << CSI2_RX_CFG1_VC_MODE;
 	val |= 1 << CSI2_RX_CFG1_MISR_EN;
 	writel_relaxed(val, csid->base + CSID_CSI2_RX_CFG1); // csi2_vc_mode_shift_val ?
 
-	/* error irqs start at BIT(11) */
-	writel_relaxed(~0u, csid->base + CSID_CSI2_RX_IRQ_MASK);
-
-	/* RDI irq */
-	writel_relaxed(~0u, csid->base + CSID_TOP_IRQ_MASK);
+	if (enable)
+		val = HALT_CMD_RESUME_AT_FRAME_BOUNDARY << RDI_CTRL_HALT_CMD;
+	else
+		val = HALT_CMD_HALT_AT_FRAME_BOUNDARY << RDI_CTRL_HALT_CMD;
+	writel_relaxed(val, csid->base + CSID_RDI_CTRL(vc));
+}
 
-	val = 1 << RDI_CTRL_HALT_CMD;
-	writel_relaxed(val, csid->base + CSID_RDI_CTRL(0));
+static void csid_configure_stream(struct csid_device *csid, u8 enable)
+{
+	u8 i;
+	/* Loop through all enabled VCs and configure stream for each */
+	for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS; i++)
+		if (csid->phy.en_vc & BIT(i))
+			__csid_configure_stream(csid, enable, i);
 }
 
 static int csid_configure_testgen_pattern(struct csid_device *csid, s32 val)
@@ -496,6 +503,7 @@
 	struct csid_device *csid = dev;
 	u32 val;
 	u8 reset_done;
+	int i;
 
 	val = readl_relaxed(csid->base + CSID_TOP_IRQ_STATUS);
 	writel_relaxed(val, csid->base + CSID_TOP_IRQ_CLEAR);
@@ -504,8 +512,12 @@
 	val = readl_relaxed(csid->base + CSID_CSI2_RX_IRQ_STATUS);
 	writel_relaxed(val, csid->base + CSID_CSI2_RX_IRQ_CLEAR);
 
-	val = readl_relaxed(csid->base + CSID_CSI2_RDIN_IRQ_STATUS(0));
-	writel_relaxed(val, csid->base + CSID_CSI2_RDIN_IRQ_CLEAR(0));
+	/* Read and clear IRQ status for each enabled RDI channel */
+	for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS; i++)
+		if (csid->phy.en_vc & BIT(i)) {
+			val = readl_relaxed(csid->base + CSID_CSI2_RDIN_IRQ_STATUS(i));
+			writel_relaxed(val, csid->base + CSID_CSI2_RDIN_IRQ_CLEAR(i));
+		}
 
 	val = 1 << IRQ_CMD_CLEAR;
 	writel_relaxed(val, csid->base + CSID_IRQ_CMD);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss-csid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss-csid.c
@@ -180,6 +180,8 @@
 			return ret;
 		}
 
+		csid->phy.need_vc_update = true;
+
 		enable_irq(csid->irq);
 
 		ret = csid->ops->reset(csid);
@@ -229,7 +231,10 @@
 			return -ENOLINK;
 	}
 
-	csid->ops->configure_stream(csid, enable);
+	if (csid->phy.need_vc_update) {
+		csid->ops->configure_stream(csid, enable);
+		csid->phy.need_vc_update = false;
+	}
 
 	return 0;
 }
@@ -440,6 +445,7 @@
 {
 	struct csid_device *csid = v4l2_get_subdevdata(sd);
 	struct v4l2_mbus_framefmt *format;
+	int i;
 
 	format = __csid_get_format(csid, sd_state, fmt->pad, fmt->which);
 	if (format == NULL)
@@ -448,14 +454,14 @@
 	csid_try_format(csid, sd_state, fmt->pad, &fmt->format, fmt->which);
 	*format = fmt->format;
 
-	/* Propagate the format from sink to source */
+	/* Propagate the format from sink to source pads */
 	if (fmt->pad == MSM_CSID_PAD_SINK) {
-		format = __csid_get_format(csid, sd_state, MSM_CSID_PAD_SRC,
-					   fmt->which);
+		for (i = MSM_CSID_PAD_FIRST_SRC; i < MSM_CSID_PADS_NUM; ++i) {
+			format = __csid_get_format(csid, sd_state, i, fmt->which);
 
-		*format = fmt->format;
-		csid_try_format(csid, sd_state, MSM_CSID_PAD_SRC, format,
-				fmt->which);
+			*format = fmt->format;
+			csid_try_format(csid, sd_state, i, format, fmt->which);
+		}
 	}
 
 	return 0;
@@ -695,7 +701,6 @@
 		struct csid_device *csid;
 		struct csiphy_device *csiphy;
 		struct csiphy_lanes_cfg *lane_cfg;
-		struct v4l2_subdev_format format = { 0 };
 
 		sd = media_entity_to_v4l2_subdev(entity);
 		csid = v4l2_get_subdevdata(sd);
@@ -718,11 +723,22 @@
 		lane_cfg = &csiphy->cfg.csi2->lane_cfg;
 		csid->phy.lane_cnt = lane_cfg->num_data;
 		csid->phy.lane_assign = csid_get_lane_assign(lane_cfg);
+	}
+	/* Decide which virtual channels to enable based on which source pads are enabled */
+	if (local->flags & MEDIA_PAD_FL_SOURCE) {
+		struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+		struct csid_device *csid = v4l2_get_subdevdata(sd);
+		struct device *dev = csid->camss->dev;
+
+		if (flags & MEDIA_LNK_FL_ENABLED)
+			csid->phy.en_vc |= BIT(local->index - 1);
+		else
+			csid->phy.en_vc &= ~BIT(local->index - 1);
+
+		csid->phy.need_vc_update = true;
 
-		/* Reset format on source pad to sink pad format */
-		format.pad = MSM_CSID_PAD_SRC;
-		format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
-		csid_set_format(&csid->subdev, NULL, &format);
+		dev_dbg(dev, "%s: Enabled CSID virtual channels mask 0x%x\n",
+			__func__, csid->phy.en_vc);
 	}
 
 	return 0;
@@ -773,6 +789,7 @@
 	struct v4l2_subdev *sd = &csid->subdev;
 	struct media_pad *pads = csid->pads;
 	struct device *dev = csid->camss->dev;
+	int i;
 	int ret;
 
 	v4l2_subdev_init(sd, &csid_v4l2_ops);
@@ -809,7 +826,8 @@
 	}
 
 	pads[MSM_CSID_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
-	pads[MSM_CSID_PAD_SRC].flags = MEDIA_PAD_FL_SOURCE;
+	for (i = MSM_CSID_PAD_FIRST_SRC; i < MSM_CSID_PADS_NUM; ++i)
+		pads[i].flags = MEDIA_PAD_FL_SOURCE;
 
 	sd->entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
 	sd->entity.ops = &csid_media_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss-csid.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss-csid.h
@@ -19,8 +19,13 @@
 #include <media/v4l2-subdev.h>
 
 #define MSM_CSID_PAD_SINK 0
-#define MSM_CSID_PAD_SRC 1
-#define MSM_CSID_PADS_NUM 2
+#define MSM_CSID_PAD_FIRST_SRC 1
+#define MSM_CSID_PADS_NUM 5
+
+#define MSM_CSID_PAD_SRC (MSM_CSID_PAD_FIRST_SRC)
+
+/* CSID hardware can demultiplex up to 4 outputs */
+#define MSM_CSID_MAX_SRC_STREAMS	4
 
 #define DATA_TYPE_EMBEDDED_DATA_8BIT	0x12
 #define DATA_TYPE_YUV420_8BIT		0x18
@@ -81,6 +86,8 @@
 	u8 csiphy_id;
 	u8 lane_cnt;
 	u32 lane_assign;
+	u32 en_vc;
+	u8 need_vc_update;
 };
 
 struct csid_device;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss-vfe-170.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss-vfe-170.c
@@ -7,7 +7,6 @@
  * Copyright (C) 2020-2021 Linaro Ltd.
  */
 
-#include <linux/delay.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
@@ -399,17 +398,7 @@
  */
 static int vfe_halt(struct vfe_device *vfe)
 {
-	unsigned long time;
-
-	reinit_completion(&vfe->halt_complete);
-
-	time = wait_for_completion_timeout(&vfe->halt_complete,
-					   msecs_to_jiffies(VFE_HALT_TIMEOUT_MS));
-	if (!time) {
-		dev_err(vfe->camss->dev, "VFE halt timeout\n");
-		return -EIO;
-	}
-
+	/* rely on vfe_disable_output() to stop the VFE */
 	return 0;
 }
 
@@ -508,35 +497,20 @@
 	return 0;
 }
 
-static int vfe_disable_output(struct vfe_line *line)
+static void vfe_disable_output(struct vfe_line *line)
 {
 	struct vfe_device *vfe = to_vfe(line);
 	struct vfe_output *output = &line->output;
 	unsigned long flags;
 	unsigned int i;
-	bool done;
-	int timeout = 0;
-
-	do {
-		spin_lock_irqsave(&vfe->output_lock, flags);
-		done = !output->gen2.active_num;
-		spin_unlock_irqrestore(&vfe->output_lock, flags);
-		usleep_range(10000, 20000);
-
-		if (timeout++ == 100) {
-			dev_err(vfe->camss->dev, "VFE idle timeout - resetting\n");
-			vfe_reset(vfe);
-			output->gen2.active_num = 0;
-			return 0;
-		}
-	} while (!done);
 
 	spin_lock_irqsave(&vfe->output_lock, flags);
 	for (i = 0; i < output->wm_num; i++)
 		vfe_wm_stop(vfe, output->wm_idx[i]);
+	output->gen2.active_num = 0;
 	spin_unlock_irqrestore(&vfe->output_lock, flags);
 
-	return 0;
+	vfe_reset(vfe);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss-vfe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss-vfe.c
@@ -533,7 +533,8 @@
 		struct camss_clock *clock = &vfe->clock[i];
 
 		if (!strcmp(clock->name, "vfe0") ||
-		    !strcmp(clock->name, "vfe1")) {
+		    !strcmp(clock->name, "vfe1") ||
+		    !strcmp(clock->name, "vfe_lite")) {
 			u64 min_rate = 0;
 			unsigned long rate;
 
@@ -607,7 +608,7 @@
 	} else {
 		ret = vfe_check_clock_rates(vfe);
 		if (ret < 0)
-			goto error_pm_runtime_get;
+			goto error_pm_domain;
 	}
 	vfe->power_count++;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss-video.c
@@ -493,7 +493,7 @@
 
 	ret = media_pipeline_start(&vdev->entity, &video->pipe);
 	if (ret < 0)
-		return ret;
+		goto flush_buffers;
 
 	ret = video_check_format(video);
 	if (ret < 0)
@@ -522,6 +522,7 @@
 error:
 	media_pipeline_stop(&vdev->entity);
 
+flush_buffers:
 	video->ops->flush_buffers(video, VB2_BUF_STATE_QUEUED);
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/camss/camss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/camss/camss.c
@@ -835,8 +835,11 @@
 	struct v4l2_fwnode_bus_mipi_csi2 *mipi_csi2;
 	struct v4l2_fwnode_endpoint vep = { { 0 } };
 	unsigned int i;
+	int ret;
 
-	v4l2_fwnode_endpoint_parse(of_fwnode_handle(node), &vep);
+	ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(node), &vep);
+	if (ret)
+		return ret;
 
 	csd->interface.csiphy_id = vep.base.port;
 
@@ -1369,6 +1372,12 @@
 		goto err_cleanup;
 	}
 
+	ret = camss_configure_pd(camss);
+	if (ret < 0) {
+		dev_err(dev, "Failed to configure power domains: %d\n", ret);
+		goto err_cleanup;
+	}
+
 	ret = camss_init_subdevices(camss);
 	if (ret < 0)
 		goto err_cleanup;
@@ -1421,12 +1430,6 @@
 		}
 	}
 
-	ret = camss_configure_pd(camss);
-	if (ret < 0) {
-		dev_err(dev, "Failed to configure power domains: %d\n", ret);
-		return ret;
-	}
-
 	pm_runtime_enable(dev);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/core.c
@@ -349,11 +349,11 @@
 
 	ret = venus_firmware_init(core);
 	if (ret)
-		goto err_runtime_disable;
+		goto err_of_depopulate;
 
 	ret = venus_boot(core);
 	if (ret)
-		goto err_runtime_disable;
+		goto err_firmware_deinit;
 
 	ret = hfi_core_resume(core, true);
 	if (ret)
@@ -385,10 +385,14 @@
 	v4l2_device_unregister(&core->v4l2_dev);
 err_venus_shutdown:
 	venus_shutdown(core);
+err_firmware_deinit:
+	venus_firmware_deinit(core);
+err_of_depopulate:
+	of_platform_depopulate(dev);
 err_runtime_disable:
 	pm_runtime_put_noidle(dev);
-	pm_runtime_set_suspended(dev);
 	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
 	hfi_destroy(core);
 err_core_deinit:
 	hfi_core_deinit(core, false);
@@ -405,6 +409,7 @@
 	struct device *dev = core->dev;
 	int ret;
 
+	cancel_delayed_work_sync(&core->work);
 	ret = pm_runtime_get_sync(dev);
 	WARN_ON(ret < 0);
 
@@ -472,7 +477,8 @@
 err_video_path:
 	icc_set_bw(core->cpucfg_path, kbps_to_icc(1000), 0);
 err_cpucfg_path:
-	pm_ops->core_power(core, POWER_ON);
+	if (pm_ops->core_power)
+		pm_ops->core_power(core, POWER_ON);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/core.h
@@ -310,6 +310,14 @@
 	VENUS_DEC_STATE_DRC		= 7,
 };
 
+enum venus_enc_state {
+	VENUS_ENC_STATE_DEINIT		= 0,
+	VENUS_ENC_STATE_INIT		= 1,
+	VENUS_ENC_STATE_ENCODING	= 2,
+	VENUS_ENC_STATE_STOPPED		= 3,
+	VENUS_ENC_STATE_DRAIN		= 4,
+};
+
 struct venus_ts_metadata {
 	bool used;
 	u64 ts_ns;
@@ -373,6 +381,7 @@
  * @sequence_out:	a sequence counter for output queue
  * @m2m_dev:	a reference to m2m device structure
  * @m2m_ctx:	a reference to m2m context structure
+ * @ctx_q_lock:	a lock to serialize video device ioctl calls
  * @state:	current state of the instance
  * @done:	a completion for sync HFI operation
  * @error:	an error returned during last HFI sync operation
@@ -415,6 +424,7 @@
 	u8 quantization;
 	u8 xfer_func;
 	enum venus_dec_state codec_state;
+	enum venus_enc_state enc_state;
 	wait_queue_head_t reconf_wait;
 	unsigned int subscriptions;
 	int buf_count;
@@ -439,6 +449,7 @@
 	u32 sequence_out;
 	struct v4l2_m2m_dev *m2m_dev;
 	struct v4l2_m2m_ctx *m2m_ctx;
+	struct mutex ctx_q_lock;
 	unsigned int state;
 	struct completion done;
 	unsigned int error;
@@ -452,6 +463,7 @@
 	bool next_buf_last;
 	bool drain_active;
 	enum venus_inst_modes flags;
+	struct ida dpb_ids;
 };
 
 #define IS_V1(core)	((core)->res->hfi_version == HFI_VERSION_1XX)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/helpers.c
@@ -3,6 +3,7 @@
  * Copyright (c) 2012-2016, The Linux Foundation. All rights reserved.
  * Copyright (C) 2017 Linaro Ltd.
  */
+#include <linux/idr.h>
 #include <linux/list.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
@@ -21,6 +22,11 @@
 #define NUM_MBS_720P	(((1280 + 15) >> 4) * ((720 + 15) >> 4))
 #define NUM_MBS_4K	(((4096 + 15) >> 4) * ((2304 + 15) >> 4))
 
+enum dpb_buf_owner {
+	DRIVER,
+	FIRMWARE,
+};
+
 struct intbuf {
 	struct list_head list;
 	u32 type;
@@ -28,6 +34,8 @@
 	void *va;
 	dma_addr_t da;
 	unsigned long attrs;
+	enum dpb_buf_owner owned_by;
+	u32 dpb_out_tag;
 };
 
 bool venus_helper_check_codec(struct venus_inst *inst, u32 v4l2_pixfmt)
@@ -95,9 +103,16 @@
 		fdata.device_addr = buf->da;
 		fdata.buffer_type = buf->type;
 
+		if (buf->owned_by == FIRMWARE)
+			continue;
+
+		fdata.clnt_data = buf->dpb_out_tag;
+
 		ret = hfi_session_process_buf(inst, &fdata);
 		if (ret)
 			goto fail;
+
+		buf->owned_by = FIRMWARE;
 	}
 
 fail:
@@ -110,13 +125,19 @@
 	struct intbuf *buf, *n;
 
 	list_for_each_entry_safe(buf, n, &inst->dpbbufs, list) {
+		if (buf->owned_by == FIRMWARE)
+			continue;
+
+		ida_free(&inst->dpb_ids, buf->dpb_out_tag);
+
 		list_del_init(&buf->list);
 		dma_free_attrs(inst->core->dev, buf->size, buf->va, buf->da,
 			       buf->attrs);
 		kfree(buf);
 	}
 
-	INIT_LIST_HEAD(&inst->dpbbufs);
+	if (list_empty(&inst->dpbbufs))
+		INIT_LIST_HEAD(&inst->dpbbufs);
 
 	return 0;
 }
@@ -134,6 +155,7 @@
 	unsigned int i;
 	u32 count;
 	int ret;
+	int id;
 
 	/* no need to allocate dpb buffers */
 	if (!inst->dpb_fmt)
@@ -167,10 +189,18 @@
 		buf->va = dma_alloc_attrs(dev, buf->size, &buf->da, GFP_KERNEL,
 					  buf->attrs);
 		if (!buf->va) {
-			kfree(buf);
 			ret = -ENOMEM;
 			goto fail;
 		}
+		buf->owned_by = DRIVER;
+
+		id = ida_alloc_min(&inst->dpb_ids, VB2_MAX_FRAME, GFP_KERNEL);
+		if (id < 0) {
+			ret = id;
+			goto fail;
+		}
+
+		buf->dpb_out_tag = id;
 
 		list_add_tail(&buf->list, &inst->dpbbufs);
 	}
@@ -178,6 +208,7 @@
 	return 0;
 
 fail:
+	kfree(buf);
 	venus_helper_free_dpb_bufs(inst);
 	return ret;
 }
@@ -981,8 +1012,8 @@
 	u32 extradata = SZ_16K;
 	u32 size;
 
-	y_stride = ALIGN(ALIGN(width, 192) * 4 / 3, 256);
-	uv_stride = ALIGN(ALIGN(width, 192) * 4 / 3, 256);
+	y_stride = ALIGN(width * 4 / 3, 256);
+	uv_stride = ALIGN(width * 4 / 3, 256);
 	y_sclines = ALIGN(height, 16);
 	uv_sclines = ALIGN((height + 1) >> 1, 16);
 
@@ -1365,6 +1396,24 @@
 }
 EXPORT_SYMBOL_GPL(venus_helper_find_buf);
 
+void venus_helper_change_dpb_owner(struct venus_inst *inst,
+				   struct vb2_v4l2_buffer *vbuf, unsigned int type,
+				   unsigned int buf_type, u32 tag)
+{
+	struct intbuf *dpb_buf;
+
+	if (!V4L2_TYPE_IS_CAPTURE(type) ||
+	    buf_type != inst->dpb_buftype)
+		return;
+
+	list_for_each_entry(dpb_buf, &inst->dpbbufs, list)
+		if (dpb_buf->dpb_out_tag == tag) {
+			dpb_buf->owned_by = DRIVER;
+			break;
+		}
+}
+EXPORT_SYMBOL_GPL(venus_helper_change_dpb_owner);
+
 int venus_helper_vb2_buf_init(struct vb2_buffer *vb)
 {
 	struct venus_inst *inst = vb2_get_drv_priv(vb->vb2_queue);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/helpers.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/helpers.h
@@ -14,6 +14,9 @@
 bool venus_helper_check_codec(struct venus_inst *inst, u32 v4l2_pixfmt);
 struct vb2_v4l2_buffer *venus_helper_find_buf(struct venus_inst *inst,
 					      unsigned int type, u32 idx);
+void venus_helper_change_dpb_owner(struct venus_inst *inst,
+				   struct vb2_v4l2_buffer *vbuf, unsigned int type,
+				   unsigned int buf_type, u32 idx);
 void venus_helper_buffers_done(struct venus_inst *inst, unsigned int type,
 			       enum vb2_buffer_state state);
 int venus_helper_vb2_buf_init(struct vb2_buffer *vb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/hfi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/hfi.c
@@ -104,6 +104,9 @@
 		mutex_lock(&core->lock);
 	}
 
+	if (!core->ops)
+		goto unlock;
+
 	ret = core->ops->core_deinit(core);
 
 	if (!ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/hfi_cmds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/hfi_cmds.c
@@ -1054,6 +1054,8 @@
 		pkt->shdr.hdr.size += sizeof(u32) + sizeof(*info);
 		break;
 	}
+	case HFI_PROPERTY_PARAM_VENC_HDR10_PQ_SEI:
+		return -ENOTSUPP;
 
 	/* FOLLOWING PROPERTIES ARE NOT IMPLEMENTED IN CORE YET */
 	case HFI_PROPERTY_CONFIG_BUFFER_REQUIREMENTS:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/hfi_msgs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/hfi_msgs.c
@@ -367,7 +367,7 @@
 		memcpy(&bufreq[idx], buf_req, sizeof(*bufreq));
 		idx++;
 
-		if (idx > HFI_BUFFER_TYPE_MAX)
+		if (idx >= HFI_BUFFER_TYPE_MAX)
 			return HFI_ERR_SESSION_INVALID_PARAMETER;
 
 		req_bytes -= sizeof(struct hfi_buffer_requirements);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/hfi_parser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/hfi_parser.c
@@ -19,6 +19,9 @@
 	struct hfi_plat_caps *caps = core->caps, *cap;
 	unsigned long bit;
 
+	if (hweight_long(core->dec_codecs) + hweight_long(core->enc_codecs) > MAX_CODEC_NUM)
+		return;
+
 	for_each_set_bit(bit, &core->dec_codecs, MAX_CODEC_NUM) {
 		cap = &caps[core->codecs_count++];
 		cap->codec = BIT(bit);
@@ -86,6 +89,9 @@
 {
 	const struct hfi_profile_level *pl = data;
 
+	if (cap->num_pl + num >= HFI_MAX_PROFILE_COUNT)
+		return;
+
 	memcpy(&cap->pl[cap->num_pl], pl, num * sizeof(*pl));
 	cap->num_pl += num;
 }
@@ -111,6 +117,9 @@
 {
 	const struct hfi_capability *caps = data;
 
+	if (cap->num_caps + num >= MAX_CAP_ENTRIES)
+		return;
+
 	memcpy(&cap->caps[cap->num_caps], caps, num * sizeof(*caps));
 	cap->num_caps += num;
 }
@@ -137,6 +146,9 @@
 {
 	const struct raw_formats *formats = fmts;
 
+	if (cap->num_fmts + num_fmts >= MAX_FMT_ENTRIES)
+		return;
+
 	memcpy(&cap->fmts[cap->num_fmts], formats, num_fmts * sizeof(*formats));
 	cap->num_fmts += num_fmts;
 }
@@ -159,6 +171,9 @@
 		rawfmts[i].buftype = fmt->buffer_type;
 		i++;
 
+		if (i >= MAX_FMT_ENTRIES)
+			return;
+
 		if (pinfo->num_planes > MAX_PLANES)
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/hfi_venus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/hfi_venus.c
@@ -131,7 +131,6 @@
 
 static bool venus_pkt_debug;
 int venus_fw_debug = HFI_DEBUG_MSG_ERROR | HFI_DEBUG_MSG_FATAL;
-static bool venus_sys_idle_indicator;
 static bool venus_fw_low_power_mode = true;
 static int venus_hw_rsp_timeout = 1000;
 static bool venus_fw_coverage;
@@ -206,6 +205,11 @@
 
 	new_wr_idx = wr_idx + dwords;
 	wr_ptr = (u32 *)(queue->qmem.kva + (wr_idx << 2));
+
+	if (wr_ptr < (u32 *)queue->qmem.kva ||
+	    wr_ptr > (u32 *)(queue->qmem.kva + queue->qmem.size - sizeof(*wr_ptr)))
+		return -EINVAL;
+
 	if (new_wr_idx < qsize) {
 		memcpy(wr_ptr, packet, dwords << 2);
 	} else {
@@ -273,6 +277,11 @@
 	}
 
 	rd_ptr = (u32 *)(queue->qmem.kva + (rd_idx << 2));
+
+	if (rd_ptr < (u32 *)queue->qmem.kva ||
+	    rd_ptr > (u32 *)(queue->qmem.kva + queue->qmem.size - sizeof(*rd_ptr)))
+		return -EINVAL;
+
 	dwords = *rd_ptr >> 2;
 	if (!dwords)
 		return -EINVAL;
@@ -454,7 +463,6 @@
 	void __iomem *wrapper_base = hdev->core->wrapper_base;
 	int ret = 0;
 
-	writel(BIT(VIDC_CTRL_INIT_CTRL_SHIFT), cpu_cs_base + VIDC_CTRL_INIT);
 	if (IS_V6(hdev->core)) {
 		mask_val = readl(wrapper_base + WRAPPER_INTR_MASK);
 		mask_val &= ~(WRAPPER_INTR_MASK_A2HWD_BASK_V6 |
@@ -465,6 +473,7 @@
 	writel(mask_val, wrapper_base + WRAPPER_INTR_MASK);
 	writel(1, cpu_cs_base + CPU_CS_SCIACMDARG3);
 
+	writel(BIT(VIDC_CTRL_INIT_CTRL_SHIFT), cpu_cs_base + VIDC_CTRL_INIT);
 	while (!ctrl_status && count < max_tries) {
 		ctrl_status = readl(cpu_cs_base + CPU_CS_SCIACMDARG0);
 		if ((ctrl_status & CPU_CS_SCIACMDARG0_ERROR_STATUS_MASK) == 4) {
@@ -924,17 +933,12 @@
 	if (ret)
 		dev_warn(dev, "setting fw debug msg ON failed (%d)\n", ret);
 
-	/*
-	 * Idle indicator is disabled by default on some 4xx firmware versions,
-	 * enable it explicitly in order to make suspend functional by checking
-	 * WFI (wait-for-interrupt) bit.
-	 */
-	if (IS_V4(hdev->core) || IS_V6(hdev->core))
-		venus_sys_idle_indicator = true;
-
-	ret = venus_sys_set_idle_message(hdev, venus_sys_idle_indicator);
-	if (ret)
-		dev_warn(dev, "setting idle response ON failed (%d)\n", ret);
+	/* HFI_PROPERTY_SYS_IDLE_INDICATOR is not supported beyond 8916 (HFI V1) */
+	if (IS_V1(hdev->core)) {
+		ret = venus_sys_set_idle_message(hdev, false);
+		if (ret)
+			dev_warn(dev, "setting idle response ON failed (%d)\n", ret);
+	}
 
 	ret = venus_sys_set_power_control(hdev, venus_fw_low_power_mode);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/pm_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/pm_helpers.c
@@ -163,14 +163,12 @@
 	struct venus_inst *inst = NULL;
 	u32 mbs_per_sec = 0;
 
-	mutex_lock(&core->lock);
 	list_for_each_entry(inst, &core->instances, list) {
 		if (inst->session_type != session_type)
 			continue;
 
 		mbs_per_sec += load_per_instance(inst);
 	}
-	mutex_unlock(&core->lock);
 
 	return mbs_per_sec;
 }
@@ -219,14 +217,12 @@
 	struct venus_inst *inst = NULL;
 	u32 mbs_per_sec, avg, peak, total_avg = 0, total_peak = 0;
 
-	mutex_lock(&core->lock);
 	list_for_each_entry(inst, &core->instances, list) {
 		mbs_per_sec = load_per_instance(inst);
 		mbs_to_bw(inst, mbs_per_sec, &avg, &peak);
 		total_avg += avg;
 		total_peak += peak;
 	}
-	mutex_unlock(&core->lock);
 
 	/*
 	 * keep minimum bandwidth vote for "video-mem" path,
@@ -253,8 +249,9 @@
 	struct device *dev = core->dev;
 	u32 mbs_per_sec;
 	unsigned int i;
-	int ret;
+	int ret = 0;
 
+	mutex_lock(&core->lock);
 	mbs_per_sec = load_per_type(core, VIDC_SESSION_TYPE_ENC) +
 		      load_per_type(core, VIDC_SESSION_TYPE_DEC);
 
@@ -279,17 +276,19 @@
 	if (ret) {
 		dev_err(dev, "failed to set clock rate %lu (%d)\n",
 			freq, ret);
-		return ret;
+		goto exit;
 	}
 
 	ret = load_scale_bw(core);
 	if (ret) {
 		dev_err(dev, "failed to set bandwidth (%d)\n",
 			ret);
-		return ret;
+		goto exit;
 	}
 
-	return 0;
+exit:
+	mutex_unlock(&core->lock);
+	return ret;
 }
 
 static int core_get_v1(struct venus_core *core)
@@ -587,8 +586,8 @@
 		if (inst->session_type == VIDC_SESSION_TYPE_DEC)
 			vpp_freq = inst_pos->clk_data.vpp_freq;
 		else if (inst->session_type == VIDC_SESSION_TYPE_ENC)
-			vpp_freq = low_power ? inst_pos->clk_data.vpp_freq :
-				inst_pos->clk_data.low_power_freq;
+			vpp_freq = low_power ? inst_pos->clk_data.low_power_freq :
+				inst_pos->clk_data.vpp_freq;
 		else
 			continue;
 
@@ -870,13 +869,13 @@
 	for (i = 0; i < res->vcodec_pmdomains_num; i++) {
 		pd = dev_pm_domain_attach_by_name(dev,
 						  res->vcodec_pmdomains[i]);
-		if (IS_ERR(pd))
-			return PTR_ERR(pd);
+		if (IS_ERR_OR_NULL(pd))
+			return pd ? PTR_ERR(pd) : -ENODATA;
 		core->pmdomains[i] = pd;
 	}
 
 skip_pmdomains:
-	if (!core->has_opp_table)
+	if (!core->res->opp_pmdomain)
 		return 0;
 
 	/* Attach the power domain for setting performance state */
@@ -1008,6 +1007,10 @@
 	if (ret)
 		return ret;
 
+	ret = vcodec_domains_get(core);
+	if (ret)
+		return ret;
+
 	if (core->res->opp_pmdomain) {
 		ret = devm_pm_opp_of_add_table(dev);
 		if (!ret) {
@@ -1018,10 +1021,6 @@
 		}
 	}
 
-	ret = vcodec_domains_get(core);
-	if (ret)
-		return ret;
-
 	return 0;
 }
 
@@ -1085,12 +1084,16 @@
 	if (inst->state != INST_START)
 		return 0;
 
-	if (inst->session_type == VIDC_SESSION_TYPE_ENC)
+	if (inst->session_type == VIDC_SESSION_TYPE_ENC) {
 		vpp_freq_per_mb = inst->flags & VENUS_LOW_POWER ?
 			inst->clk_data.low_power_freq :
 			inst->clk_data.vpp_freq;
 
-	vpp_freq = mbs_per_sec * vpp_freq_per_mb;
+		vpp_freq = mbs_per_sec * vpp_freq_per_mb;
+	} else {
+		vpp_freq = mbs_per_sec * inst->clk_data.vpp_freq;
+	}
+
 	/* 21 / 20 is overhead factor */
 	vpp_freq += vpp_freq / 20;
 	vsp_freq = mbs_per_sec * inst->clk_data.vsp_freq;
@@ -1112,13 +1115,13 @@
 	struct device *dev = core->dev;
 	unsigned long freq = 0, freq_core1 = 0, freq_core2 = 0;
 	unsigned long filled_len = 0;
-	int i, ret;
+	int i, ret = 0;
 
 	for (i = 0; i < inst->num_input_bufs; i++)
 		filled_len = max(filled_len, inst->payloads[i]);
 
 	if (inst->session_type == VIDC_SESSION_TYPE_DEC && !filled_len)
-		return 0;
+		return ret;
 
 	freq = calculate_inst_freq(inst, filled_len);
 	inst->clk_data.freq = freq;
@@ -1134,7 +1137,6 @@
 			freq_core2 += inst->clk_data.freq;
 		}
 	}
-	mutex_unlock(&core->lock);
 
 	freq = max(freq_core1, freq_core2);
 
@@ -1158,17 +1160,19 @@
 	if (ret) {
 		dev_err(dev, "failed to set clock rate %lu (%d)\n",
 			freq, ret);
-		return ret;
+		goto exit;
 	}
 
 	ret = load_scale_bw(core);
 	if (ret) {
 		dev_err(dev, "failed to set bandwidth (%d)\n",
 			ret);
-		return ret;
+		goto exit;
 	}
 
-	return 0;
+exit:
+	mutex_unlock(&core->lock);
+	return ret;
 }
 
 static const struct venus_pm_ops pm_ops_v4 = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/vdec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/vdec.c
@@ -158,6 +158,8 @@
 		else
 			return NULL;
 		fmt = find_format(inst, pixmp->pixelformat, f->type);
+		if (!fmt)
+			return NULL;
 	}
 
 	pixmp->width = clamp(pixmp->width, frame_width_min(inst),
@@ -496,6 +498,7 @@
 vdec_decoder_cmd(struct file *file, void *fh, struct v4l2_decoder_cmd *cmd)
 {
 	struct venus_inst *inst = to_inst(file);
+	struct vb2_queue *dst_vq;
 	struct hfi_frame_data fdata = {0};
 	int ret;
 
@@ -526,6 +529,13 @@
 			inst->codec_state = VENUS_DEC_STATE_DRAIN;
 			inst->drain_active = true;
 		}
+	} else if (cmd->cmd == V4L2_DEC_CMD_START &&
+		   inst->codec_state == VENUS_DEC_STATE_STOPPED) {
+		dst_vq = v4l2_m2m_get_vq(inst->fh.m2m_ctx,
+					 V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE);
+		vb2_clear_last_buffer_dequeued(dst_vq);
+
+		inst->codec_state = VENUS_DEC_STATE_DECODING;
 	}
 
 unlock:
@@ -1155,7 +1165,7 @@
 		break;
 	case VENUS_DEC_STATE_INIT:
 	case VENUS_DEC_STATE_CAPTURE_SETUP:
-		ret = hfi_session_flush(inst, HFI_FLUSH_INPUT, true);
+		ret = hfi_session_flush(inst, HFI_FLUSH_ALL, true);
 		break;
 	default:
 		break;
@@ -1306,8 +1316,10 @@
 		type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
 
 	vbuf = venus_helper_find_buf(inst, type, tag);
-	if (!vbuf)
+	if (!vbuf) {
+		venus_helper_change_dpb_owner(inst, vbuf, type, buf_type, tag);
 		return;
+	}
 
 	vbuf->flags = flags;
 	vbuf->field = V4L2_FIELD_NONE;
@@ -1525,6 +1537,7 @@
 	src_vq->allow_zero_bytesused = 1;
 	src_vq->min_buffers_needed = 0;
 	src_vq->dev = inst->core->dev;
+	src_vq->lock = &inst->ctx_q_lock;
 	ret = vb2_queue_init(src_vq);
 	if (ret)
 		return ret;
@@ -1539,6 +1552,7 @@
 	dst_vq->allow_zero_bytesused = 1;
 	dst_vq->min_buffers_needed = 0;
 	dst_vq->dev = inst->core->dev;
+	dst_vq->lock = &inst->ctx_q_lock;
 	return vb2_queue_init(dst_vq);
 }
 
@@ -1557,6 +1571,7 @@
 	INIT_LIST_HEAD(&inst->internalbufs);
 	INIT_LIST_HEAD(&inst->list);
 	mutex_init(&inst->lock);
+	mutex_init(&inst->ctx_q_lock);
 
 	inst->core = core;
 	inst->session_type = VIDC_SESSION_TYPE_DEC;
@@ -1580,6 +1595,8 @@
 
 	vdec_inst_init(inst);
 
+	ida_init(&inst->dpb_ids);
+
 	/*
 	 * create m2m device for every instance, the m2m context scheduling
 	 * is made by firmware side so we do not need to care about.
@@ -1622,11 +1639,14 @@
 
 	vdec_pm_get(inst);
 
+	cancel_work_sync(&inst->delayed_process_work);
 	v4l2_m2m_ctx_release(inst->m2m_ctx);
 	v4l2_m2m_release(inst->m2m_dev);
 	vdec_ctrl_deinit(inst);
+	ida_destroy(&inst->dpb_ids);
 	hfi_session_destroy(inst);
 	mutex_destroy(&inst->lock);
+	mutex_destroy(&inst->ctx_q_lock);
 	v4l2_fh_del(&inst->fh);
 	v4l2_fh_exit(&inst->fh);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/venc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/venc.c
@@ -509,6 +509,64 @@
 	return 0;
 }
 
+static int venc_subscribe_event(struct v4l2_fh *fh,
+				const struct v4l2_event_subscription *sub)
+{
+	switch (sub->type) {
+	case V4L2_EVENT_EOS:
+		return v4l2_event_subscribe(fh, sub, 2, NULL);
+	case V4L2_EVENT_CTRL:
+		return v4l2_ctrl_subscribe_event(fh, sub);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int
+venc_encoder_cmd(struct file *file, void *fh, struct v4l2_encoder_cmd *cmd)
+{
+	struct venus_inst *inst = to_inst(file);
+	struct hfi_frame_data fdata = {0};
+	int ret = 0;
+
+	ret = v4l2_m2m_ioctl_try_encoder_cmd(file, fh, cmd);
+	if (ret)
+		return ret;
+
+	mutex_lock(&inst->lock);
+
+	if (cmd->cmd == V4L2_ENC_CMD_STOP &&
+	    inst->enc_state == VENUS_ENC_STATE_ENCODING) {
+		/*
+		 * Implement V4L2_ENC_CMD_STOP by enqueue an empty buffer on
+		 * encoder input to signal EOS.
+		 */
+		if (!(inst->streamon_out && inst->streamon_cap))
+			goto unlock;
+
+		fdata.buffer_type = HFI_BUFFER_INPUT;
+		fdata.flags |= HFI_BUFFERFLAG_EOS;
+		fdata.device_addr = 0xdeadb000;
+
+		ret = hfi_session_process_buf(inst, &fdata);
+
+		inst->enc_state = VENUS_ENC_STATE_DRAIN;
+	} else if (cmd->cmd == V4L2_ENC_CMD_START) {
+		if (inst->enc_state == VENUS_ENC_STATE_DRAIN) {
+			ret = -EBUSY;
+			goto unlock;
+		}
+		if (inst->enc_state == VENUS_ENC_STATE_STOPPED) {
+			vb2_clear_last_buffer_dequeued(&inst->fh.m2m_ctx->cap_q_ctx.q);
+			inst->enc_state = VENUS_ENC_STATE_ENCODING;
+		}
+	}
+
+unlock:
+	mutex_unlock(&inst->lock);
+	return ret;
+}
+
 static const struct v4l2_ioctl_ops venc_ioctl_ops = {
 	.vidioc_querycap = venc_querycap,
 	.vidioc_enum_fmt_vid_cap = venc_enum_fmt,
@@ -534,10 +592,70 @@
 	.vidioc_g_parm = venc_g_parm,
 	.vidioc_enum_framesizes = venc_enum_framesizes,
 	.vidioc_enum_frameintervals = venc_enum_frameintervals,
-	.vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
+	.vidioc_subscribe_event = venc_subscribe_event,
 	.vidioc_unsubscribe_event = v4l2_event_unsubscribe,
+	.vidioc_try_encoder_cmd = v4l2_m2m_ioctl_try_encoder_cmd,
+	.vidioc_encoder_cmd = venc_encoder_cmd,
 };
 
+static int venc_pm_get(struct venus_inst *inst)
+{
+	struct venus_core *core = inst->core;
+	struct device *dev = core->dev_enc;
+	int ret;
+
+	mutex_lock(&core->pm_lock);
+	ret = pm_runtime_resume_and_get(dev);
+	mutex_unlock(&core->pm_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int venc_pm_put(struct venus_inst *inst, bool autosuspend)
+{
+	struct venus_core *core = inst->core;
+	struct device *dev = core->dev_enc;
+	int ret;
+
+	mutex_lock(&core->pm_lock);
+
+	if (autosuspend)
+		ret = pm_runtime_put_autosuspend(dev);
+	else
+		ret = pm_runtime_put_sync(dev);
+
+	mutex_unlock(&core->pm_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int venc_pm_get_put(struct venus_inst *inst)
+{
+	struct venus_core *core = inst->core;
+	struct device *dev = core->dev_enc;
+	int ret = 0;
+
+	mutex_lock(&core->pm_lock);
+
+	if (pm_runtime_suspended(dev)) {
+		ret = pm_runtime_resume_and_get(dev);
+		if (ret < 0)
+			goto error;
+
+		ret = pm_runtime_put_autosuspend(dev);
+	}
+
+error:
+	mutex_unlock(&core->pm_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static void venc_pm_touch(struct venus_inst *inst)
+{
+	pm_runtime_mark_last_busy(inst->core->dev_enc);
+}
+
 static int venc_set_properties(struct venus_inst *inst)
 {
 	struct venc_controls *ctr = &inst->controls.enc;
@@ -604,8 +722,8 @@
 
 		ptype = HFI_PROPERTY_PARAM_VENC_H264_TRANSFORM_8X8;
 		h264_transform.enable_type = 0;
-		if (ctr->profile.h264 == HFI_H264_PROFILE_HIGH ||
-		    ctr->profile.h264 == HFI_H264_PROFILE_CONSTRAINED_HIGH)
+		if (ctr->profile.h264 == V4L2_MPEG_VIDEO_H264_PROFILE_HIGH ||
+		    ctr->profile.h264 == V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_HIGH)
 			h264_transform.enable_type = ctr->h264_8x8_transform;
 
 		ret = hfi_session_set_property(inst, ptype, &h264_transform);
@@ -931,11 +1049,19 @@
 		return 0;
 	}
 
+	ret = venc_pm_get(inst);
+	if (ret)
+		return ret;
+
 	mutex_lock(&inst->lock);
 	ret = venc_init_session(inst);
 	mutex_unlock(&inst->lock);
 
 	if (ret)
+		goto put_power;
+
+	ret = venc_pm_put(inst, false);
+	if (ret)
 		return ret;
 
 	switch (q->type) {
@@ -971,6 +1097,9 @@
 	}
 
 	return ret;
+put_power:
+	venc_pm_put(inst, false);
+	return ret;
 }
 
 static int venc_buf_init(struct vb2_buffer *vb)
@@ -986,6 +1115,8 @@
 {
 	int ret;
 
+	venc_pm_get(inst);
+
 	mutex_lock(&inst->lock);
 
 	ret = hfi_session_deinit(inst);
@@ -997,6 +1128,8 @@
 	venus_pm_load_scale(inst);
 	INIT_LIST_HEAD(&inst->registeredbufs);
 	venus_pm_release_core(inst);
+
+	venc_pm_put(inst, false);
 }
 
 static void venc_buf_cleanup(struct vb2_buffer *vb)
@@ -1066,8 +1199,16 @@
 	inst->sequence_cap = 0;
 	inst->sequence_out = 0;
 
+	ret = venc_pm_get(inst);
+	if (ret)
+		goto error;
+
 	ret = venus_pm_acquire_core(inst);
 	if (ret)
+		goto put_power;
+
+	ret = venc_pm_put(inst, true);
+	if (ret)
 		goto error;
 
 	ret = venc_set_properties(inst);
@@ -1087,10 +1228,14 @@
 	if (ret)
 		goto error;
 
+	inst->enc_state = VENUS_ENC_STATE_ENCODING;
+
 	mutex_unlock(&inst->lock);
 
 	return 0;
 
+put_power:
+	venc_pm_put(inst, false);
 error:
 	venus_helper_buffers_done(inst, q->type, VB2_BUF_STATE_QUEUED);
 	if (q->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
@@ -1104,8 +1249,21 @@
 static void venc_vb2_buf_queue(struct vb2_buffer *vb)
 {
 	struct venus_inst *inst = vb2_get_drv_priv(vb->vb2_queue);
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+
+	venc_pm_get_put(inst);
 
 	mutex_lock(&inst->lock);
+
+	if (inst->enc_state == VENUS_ENC_STATE_STOPPED) {
+		vbuf->sequence = inst->sequence_cap++;
+		vbuf->field = V4L2_FIELD_NONE;
+		vb2_set_plane_payload(vb, 0, 0);
+		v4l2_m2m_buf_done(vbuf, VB2_BUF_STATE_DONE);
+		mutex_unlock(&inst->lock);
+		return;
+	}
+
 	venus_helper_vb2_buf_queue(vb);
 	mutex_unlock(&inst->lock);
 }
@@ -1128,6 +1286,8 @@
 	struct vb2_buffer *vb;
 	unsigned int type;
 
+	venc_pm_touch(inst);
+
 	if (buf_type == HFI_BUFFER_INPUT)
 		type = V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE;
 	else
@@ -1145,6 +1305,10 @@
 		vb->planes[0].data_offset = data_offset;
 		vb->timestamp = timestamp_us * NSEC_PER_USEC;
 		vbuf->sequence = inst->sequence_cap++;
+		if ((vbuf->flags & V4L2_BUF_FLAG_LAST) &&
+		    inst->enc_state == VENUS_ENC_STATE_DRAIN) {
+			inst->enc_state = VENUS_ENC_STATE_STOPPED;
+		}
 	} else {
 		vbuf->sequence = inst->sequence_out++;
 	}
@@ -1157,6 +1321,8 @@
 {
 	struct device *dev = inst->core->dev_enc;
 
+	venc_pm_touch(inst);
+
 	if (event == EVT_SESSION_ERROR) {
 		inst->session_error = true;
 		dev_err(dev, "enc: event session error %x\n", inst->error);
@@ -1189,6 +1355,7 @@
 	src_vq->allow_zero_bytesused = 1;
 	src_vq->min_buffers_needed = 1;
 	src_vq->dev = inst->core->dev;
+	src_vq->lock = &inst->ctx_q_lock;
 	if (inst->core->res->hfi_version == HFI_VERSION_1XX)
 		src_vq->bidirectional = 1;
 	ret = vb2_queue_init(src_vq);
@@ -1205,6 +1372,7 @@
 	dst_vq->allow_zero_bytesused = 1;
 	dst_vq->min_buffers_needed = 1;
 	dst_vq->dev = inst->core->dev;
+	dst_vq->lock = &inst->ctx_q_lock;
 	return vb2_queue_init(dst_vq);
 }
 
@@ -1237,21 +1405,21 @@
 	INIT_LIST_HEAD(&inst->internalbufs);
 	INIT_LIST_HEAD(&inst->list);
 	mutex_init(&inst->lock);
+	mutex_init(&inst->ctx_q_lock);
 
 	inst->core = core;
 	inst->session_type = VIDC_SESSION_TYPE_ENC;
 	inst->clk_data.core_id = VIDC_CORE_ID_DEFAULT;
 	inst->core_acquired = false;
 
-	venus_helper_init_instance(inst);
+	if (inst->enc_state == VENUS_ENC_STATE_DEINIT)
+		inst->enc_state = VENUS_ENC_STATE_INIT;
 
-	ret = pm_runtime_resume_and_get(core->dev_enc);
-	if (ret < 0)
-		goto err_free;
+	venus_helper_init_instance(inst);
 
 	ret = venc_ctrl_init(inst);
 	if (ret)
-		goto err_put_sync;
+		goto err_free;
 
 	ret = hfi_session_create(inst, &venc_hfi_ops);
 	if (ret)
@@ -1290,8 +1458,6 @@
 	hfi_session_destroy(inst);
 err_ctrl_deinit:
 	venc_ctrl_deinit(inst);
-err_put_sync:
-	pm_runtime_put_sync(core->dev_enc);
 err_free:
 	kfree(inst);
 	return ret;
@@ -1301,15 +1467,20 @@
 {
 	struct venus_inst *inst = to_inst(file);
 
+	venc_pm_get(inst);
+
 	v4l2_m2m_ctx_release(inst->m2m_ctx);
 	v4l2_m2m_release(inst->m2m_dev);
 	venc_ctrl_deinit(inst);
 	hfi_session_destroy(inst);
 	mutex_destroy(&inst->lock);
+	mutex_destroy(&inst->ctx_q_lock);
 	v4l2_fh_del(&inst->fh);
 	v4l2_fh_exit(&inst->fh);
 
-	pm_runtime_put_sync(inst->core->dev_enc);
+	inst->enc_state = VENUS_ENC_STATE_DEINIT;
+
+	venc_pm_put(inst, false);
 
 	kfree(inst);
 	return 0;
@@ -1366,6 +1537,8 @@
 	core->dev_enc = dev;
 
 	video_set_drvdata(vdev, core);
+	pm_runtime_set_autosuspend_delay(dev, 2000);
+	pm_runtime_use_autosuspend(dev);
 	pm_runtime_enable(dev);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/qcom/venus/venc_ctrls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/qcom/venus/venc_ctrls.c
@@ -320,8 +320,8 @@
 		ctr->intra_refresh_period = ctrl->val;
 		break;
 	case V4L2_CID_MPEG_VIDEO_H264_8X8_TRANSFORM:
-		if (ctr->profile.h264 != HFI_H264_PROFILE_HIGH &&
-		    ctr->profile.h264 != HFI_H264_PROFILE_CONSTRAINED_HIGH)
+		if (ctr->profile.h264 != V4L2_MPEG_VIDEO_H264_PROFILE_HIGH &&
+		    ctr->profile.h264 != V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_HIGH)
 			return -EINVAL;
 
 		/*
@@ -457,7 +457,7 @@
 			  V4L2_CID_MPEG_VIDEO_H264_I_FRAME_MIN_QP, 1, 51, 1, 1);
 
 	v4l2_ctrl_new_std(&inst->ctrl_handler, &venc_ctrl_ops,
-			  V4L2_CID_MPEG_VIDEO_H264_8X8_TRANSFORM, 0, 1, 1, 0);
+			  V4L2_CID_MPEG_VIDEO_H264_8X8_TRANSFORM, 0, 1, 1, 1);
 
 	v4l2_ctrl_new_std(&inst->ctrl_handler, &venc_ctrl_ops,
 			  V4L2_CID_MPEG_VIDEO_H264_P_FRAME_MIN_QP, 1, 51, 1, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rcar-vin/rcar-csi2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rcar-vin/rcar-csi2.c
@@ -445,16 +445,23 @@
 static int rcsi2_set_phypll(struct rcar_csi2 *priv, unsigned int mbps)
 {
 	const struct rcsi2_mbps_reg *hsfreq;
+	const struct rcsi2_mbps_reg *hsfreq_prev = NULL;
 
-	for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++)
+	for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++) {
 		if (hsfreq->mbps >= mbps)
 			break;
+		hsfreq_prev = hsfreq;
+	}
 
 	if (!hsfreq->mbps) {
 		dev_err(priv->dev, "Unsupported PHY speed (%u Mbps)", mbps);
 		return -ERANGE;
 	}
 
+	if (hsfreq_prev &&
+	    ((mbps - hsfreq_prev->mbps) <= (hsfreq->mbps - mbps)))
+		hsfreq = hsfreq_prev;
+
 	rcsi2_write(priv, PHYPLL_REG, PHYPLL_HSFREQRANGE(hsfreq->reg));
 
 	return 0;
@@ -553,6 +560,8 @@
 
 	/* Code is validated in set_fmt. */
 	format = rcsi2_code_to_fmt(priv->mf.code);
+	if (!format)
+		return -EINVAL;
 
 	/*
 	 * Enable all supported CSI-2 channels with virtual channel and
@@ -980,10 +989,17 @@
 				 const struct rcsi2_mbps_reg *values, u16 code)
 {
 	const struct rcsi2_mbps_reg *value;
+	const struct rcsi2_mbps_reg *prev_value = NULL;
 
-	for (value = values; value->mbps; value++)
+	for (value = values; value->mbps; value++) {
 		if (value->mbps >= mbps)
 			break;
+		prev_value = value;
+	}
+
+	if (prev_value &&
+	    ((mbps - prev_value->mbps) <= (value->mbps - mbps)))
+		value = prev_value;
 
 	if (!value->mbps) {
 		dev_err(priv->dev, "Unsupported PHY speed (%u Mbps)", mbps);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rcar-vin/rcar-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rcar-vin/rcar-dma.c
@@ -644,11 +644,9 @@
 	case V4L2_FIELD_SEQ_TB:
 	case V4L2_FIELD_SEQ_BT:
 	case V4L2_FIELD_NONE:
-		vnmc = VNMC_IM_ODD_EVEN;
-		progressive = true;
-		break;
 	case V4L2_FIELD_ALTERNATE:
 		vnmc = VNMC_IM_ODD_EVEN;
+		progressive = true;
 		break;
 	default:
 		vnmc = VNMC_IM_ODD;
@@ -904,7 +902,8 @@
 				vin->format.sizeimage / 2;
 			break;
 		}
-	} else if (vin->state != RUNNING || list_empty(&vin->buf_list)) {
+	} else if ((vin->state != STOPPED && vin->state != RUNNING) ||
+		   list_empty(&vin->buf_list)) {
 		vin->buf_hw[slot].buffer = NULL;
 		vin->buf_hw[slot].type = FULL;
 		phys_addr = vin->scratch_phys;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rcar-vin/rcar-v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rcar-vin/rcar-v4l2.c
@@ -175,20 +175,27 @@
 		break;
 	}
 
-	/* HW limit width to a multiple of 32 (2^5) for NV12/16 else 2 (2^1) */
+	/* Hardware limits width alignment based on format. */
 	switch (pix->pixelformat) {
+	/* Multiple of 32 (2^5) for NV12/16. */
 	case V4L2_PIX_FMT_NV12:
 	case V4L2_PIX_FMT_NV16:
 		walign = 5;
 		break;
-	default:
+	/* Multiple of 2 (2^1) for YUV. */
+	case V4L2_PIX_FMT_YUYV:
+	case V4L2_PIX_FMT_UYVY:
 		walign = 1;
 		break;
+	/* No multiple for RGB. */
+	default:
+		walign = 0;
+		break;
 	}
 
 	/* Limit to VIN capabilities */
-	v4l_bound_align_image(&pix->width, 2, vin->info->max_width, walign,
-			      &pix->height, 4, vin->info->max_height, 2, 0);
+	v4l_bound_align_image(&pix->width, 5, vin->info->max_width, walign,
+			      &pix->height, 2, vin->info->max_height, 0, 0);
 
 	pix->bytesperline = rvin_format_bytesperline(vin, pix);
 	pix->sizeimage = rvin_format_sizeimage(pix);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rcar_fdp1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rcar_fdp1.c
@@ -2256,7 +2256,6 @@
 	struct fdp1_dev *fdp1;
 	struct video_device *vfd;
 	struct device_node *fcp_node;
-	struct resource *res;
 	struct clk *clk;
 	unsigned int i;
 
@@ -2283,17 +2282,15 @@
 	platform_set_drvdata(pdev, fdp1);
 
 	/* Memory-mapped registers */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	fdp1->regs = devm_ioremap_resource(&pdev->dev, res);
+	fdp1->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(fdp1->regs))
 		return PTR_ERR(fdp1->regs);
 
 	/* Interrupt service routine registration */
-	fdp1->irq = ret = platform_get_irq(pdev, 0);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "cannot find IRQ\n");
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0)
 		return ret;
-	}
+	fdp1->irq = ret;
 
 	ret = devm_request_irq(&pdev->dev, fdp1->irq, fdp1_irq_handler, 0,
 			       dev_name(&pdev->dev), fdp1);
@@ -2316,8 +2313,10 @@
 
 	/* Determine our clock rate */
 	clk = clk_get(&pdev->dev, NULL);
-	if (IS_ERR(clk))
-		return PTR_ERR(clk);
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		goto put_dev;
+	}
 
 	fdp1->clk_rate = clk_get_rate(clk);
 	clk_put(clk);
@@ -2326,7 +2325,7 @@
 	ret = v4l2_device_register(&pdev->dev, &fdp1->v4l2_dev);
 	if (ret) {
 		v4l2_err(&fdp1->v4l2_dev, "Failed to register video device\n");
-		return ret;
+		goto put_dev;
 	}
 
 	/* M2M registration */
@@ -2396,10 +2395,12 @@
 unreg_dev:
 	v4l2_device_unregister(&fdp1->v4l2_dev);
 
+put_dev:
+	rcar_fcp_put(fdp1->fcp);
 	return ret;
 }
 
-static int fdp1_remove(struct platform_device *pdev)
+static void fdp1_remove(struct platform_device *pdev)
 {
 	struct fdp1_dev *fdp1 = platform_get_drvdata(pdev);
 
@@ -2407,8 +2408,7 @@
 	video_unregister_device(&fdp1->vfd);
 	v4l2_device_unregister(&fdp1->v4l2_dev);
 	pm_runtime_disable(&pdev->dev);
-
-	return 0;
+	rcar_fcp_put(fdp1->fcp);
 }
 
 static int __maybe_unused fdp1_pm_runtime_suspend(struct device *dev)
@@ -2444,7 +2444,7 @@
 
 static struct platform_driver fdp1_pdrv = {
 	.probe		= fdp1_probe,
-	.remove		= fdp1_remove,
+	.remove_new	= fdp1_remove,
 	.driver		= {
 		.name	= DRIVER_NAME,
 		.of_match_table = fdp1_dt_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rockchip/rga/rga.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rockchip/rga/rga.c
@@ -187,7 +187,7 @@
 static struct rga_fmt formats[] = {
 	{
 		.fourcc = V4L2_PIX_FMT_ARGB32,
-		.color_swap = RGA_COLOR_RB_SWAP,
+		.color_swap = RGA_COLOR_ALPHA_SWAP,
 		.hw_format = RGA_COLOR_FMT_ABGR8888,
 		.depth = 32,
 		.uv_factor = 1,
@@ -195,17 +195,8 @@
 		.x_div = 1,
 	},
 	{
-		.fourcc = V4L2_PIX_FMT_XRGB32,
-		.color_swap = RGA_COLOR_RB_SWAP,
-		.hw_format = RGA_COLOR_FMT_XBGR8888,
-		.depth = 32,
-		.uv_factor = 1,
-		.y_div = 1,
-		.x_div = 1,
-	},
-	{
 		.fourcc = V4L2_PIX_FMT_ABGR32,
-		.color_swap = RGA_COLOR_ALPHA_SWAP,
+		.color_swap = RGA_COLOR_RB_SWAP,
 		.hw_format = RGA_COLOR_FMT_ABGR8888,
 		.depth = 32,
 		.uv_factor = 1,
@@ -214,7 +205,7 @@
 	},
 	{
 		.fourcc = V4L2_PIX_FMT_XBGR32,
-		.color_swap = RGA_COLOR_ALPHA_SWAP,
+		.color_swap = RGA_COLOR_RB_SWAP,
 		.hw_format = RGA_COLOR_FMT_XBGR8888,
 		.depth = 32,
 		.uv_factor = 1,
@@ -868,7 +859,7 @@
 
 	ret = pm_runtime_resume_and_get(rga->dev);
 	if (ret < 0)
-		goto rel_vdev;
+		goto rel_m2m;
 
 	rga->version.major = (rga_read(rga, RGA_VERSION_INFO) >> 24) & 0xFF;
 	rga->version.minor = (rga_read(rga, RGA_VERSION_INFO) >> 20) & 0x0F;
@@ -884,7 +875,7 @@
 					   DMA_ATTR_WRITE_COMBINE);
 	if (!rga->cmdbuf_virt) {
 		ret = -ENOMEM;
-		goto rel_vdev;
+		goto rel_m2m;
 	}
 
 	rga->src_mmu_pages =
@@ -895,7 +886,7 @@
 	}
 	rga->dst_mmu_pages =
 		(unsigned int *)__get_free_pages(GFP_KERNEL | __GFP_ZERO, 3);
-	if (rga->dst_mmu_pages) {
+	if (!rga->dst_mmu_pages) {
 		ret = -ENOMEM;
 		goto free_src_pages;
 	}
@@ -921,6 +912,8 @@
 free_dma:
 	dma_free_attrs(rga->dev, RGA_CMDBUF_SIZE, rga->cmdbuf_virt,
 		       rga->cmdbuf_phy, DMA_ATTR_WRITE_COMBINE);
+rel_m2m:
+	v4l2_m2m_release(rga->m2m_dev);
 rel_vdev:
 	video_device_release(vfd);
 unreg_v4l2_dev:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rockchip/rkisp1/rkisp1-capture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rockchip/rkisp1/rkisp1-capture.c
@@ -1270,11 +1270,12 @@
 	struct rkisp1_capture *cap = video_get_drvdata(vdev);
 	const struct rkisp1_capture_fmt_cfg *fmt =
 		rkisp1_find_fmt_cfg(cap, cap->pix.fmt.pixelformat);
-	struct v4l2_subdev_format sd_fmt;
+	struct v4l2_subdev_format sd_fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		.pad = link->source->index,
+	};
 	int ret;
 
-	sd_fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
-	sd_fmt.pad = link->source->index;
 	ret = v4l2_subdev_call(sd, pad, get_fmt, NULL, &sd_fmt);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c
@@ -426,7 +426,7 @@
 {
 	struct rkisp1_debug *debug = &rkisp1->debug;
 
-	debug->debugfs_dir = debugfs_create_dir(RKISP1_DRIVER_NAME, NULL);
+	debug->debugfs_dir = debugfs_create_dir(dev_name(rkisp1->dev), NULL);
 	debugfs_create_ulong("data_loss", 0444, debug->debugfs_dir,
 			     &debug->data_loss);
 	debugfs_create_ulong("outform_size_err", 0444,  debug->debugfs_dir,
@@ -514,7 +514,7 @@
 
 	ret = v4l2_device_register(rkisp1->dev, &rkisp1->v4l2_dev);
 	if (ret)
-		return ret;
+		goto err_pm_runtime_disable;
 
 	ret = media_device_register(&rkisp1->media_dev);
 	if (ret) {
@@ -534,6 +534,7 @@
 	media_device_unregister(&rkisp1->media_dev);
 err_unreg_v4l2_dev:
 	v4l2_device_unregister(&rkisp1->v4l2_dev);
+err_pm_runtime_disable:
 	pm_runtime_disable(&pdev->dev);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rockchip/rkisp1/rkisp1-params.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rockchip/rkisp1/rkisp1-params.c
@@ -275,7 +275,7 @@
 			     RKISP1_CIF_ISP_LSC_XSIZE_01 + i * 4);
 
 		/* program x grad tables */
-		data = RKISP1_CIF_ISP_LSC_SECT_SIZE(arg->x_grad_tbl[i * 2],
+		data = RKISP1_CIF_ISP_LSC_SECT_GRAD(arg->x_grad_tbl[i * 2],
 						    arg->x_grad_tbl[i * 2 + 1]);
 		rkisp1_write(params->rkisp1, data,
 			     RKISP1_CIF_ISP_LSC_XGRAD_01 + i * 4);
@@ -287,7 +287,7 @@
 			     RKISP1_CIF_ISP_LSC_YSIZE_01 + i * 4);
 
 		/* program y grad tables */
-		data = RKISP1_CIF_ISP_LSC_SECT_SIZE(arg->y_grad_tbl[i * 2],
+		data = RKISP1_CIF_ISP_LSC_SECT_GRAD(arg->y_grad_tbl[i * 2],
 						    arg->y_grad_tbl[i * 2 + 1]);
 		rkisp1_write(params->rkisp1, data,
 			     RKISP1_CIF_ISP_LSC_YGRAD_01 + i * 4);
@@ -751,7 +751,7 @@
 	}
 }
 
-static void rkisp1_csm_config(struct rkisp1_params *params, bool full_range)
+static void rkisp1_csm_config(struct rkisp1_params *params)
 {
 	static const u16 full_range_coeff[] = {
 		0x0026, 0x004b, 0x000f,
@@ -765,7 +765,7 @@
 	};
 	unsigned int i;
 
-	if (full_range) {
+	if (params->quantization == V4L2_QUANTIZATION_FULL_RANGE) {
 		for (i = 0; i < ARRAY_SIZE(full_range_coeff); i++)
 			rkisp1_write(params->rkisp1, full_range_coeff[i],
 				     RKISP1_CIF_ISP_CC_COEFF_0 + i * 4);
@@ -1235,11 +1235,7 @@
 	rkisp1_param_set_bits(params, RKISP1_CIF_ISP_HIST_PROP,
 			      rkisp1_hst_params_default_config.mode);
 
-	/* set the  range */
-	if (params->quantization == V4L2_QUANTIZATION_FULL_RANGE)
-		rkisp1_csm_config(params, true);
-	else
-		rkisp1_csm_config(params, false);
+	rkisp1_csm_config(params);
 
 	spin_lock_irq(&params->config_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rockchip/rkisp1/rkisp1-regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rockchip/rkisp1/rkisp1-regs.h
@@ -480,7 +480,7 @@
 	(((v0) & 0xFFF) | (((v1) & 0xFFF) << 12))
 #define RKISP1_CIF_ISP_LSC_SECT_SIZE(v0, v1)      \
 	(((v0) & 0xFFF) | (((v1) & 0xFFF) << 16))
-#define RKISP1_CIF_ISP_LSC_GRAD_SIZE(v0, v1)      \
+#define RKISP1_CIF_ISP_LSC_SECT_GRAD(v0, v1)      \
 	(((v0) & 0xFFF) | (((v1) & 0xFFF) << 16))
 
 /* LSC: ISP_LSC_TABLE_SEL */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/rockchip/rkisp1/rkisp1-resizer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/rockchip/rkisp1/rkisp1-resizer.c
@@ -510,6 +510,10 @@
 	sink_fmt->height = RKISP1_DEFAULT_HEIGHT;
 	sink_fmt->field = V4L2_FIELD_NONE;
 	sink_fmt->code = RKISP1_DEF_FMT;
+	sink_fmt->colorspace = V4L2_COLORSPACE_SRGB;
+	sink_fmt->xfer_func = V4L2_XFER_FUNC_SRGB;
+	sink_fmt->ycbcr_enc = V4L2_YCBCR_ENC_601;
+	sink_fmt->quantization = V4L2_QUANTIZATION_LIM_RANGE;
 
 	sink_crop = v4l2_subdev_get_try_crop(sd, sd_state,
 					     RKISP1_RSZ_PAD_SINK);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s3c-camif/camif-capture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s3c-camif/camif-capture.c
@@ -1132,12 +1132,12 @@
 
 	ret = vb2_queue_init(q);
 	if (ret)
-		goto err_vd_rel;
+		return ret;
 
 	vp->pad.flags = MEDIA_PAD_FL_SINK;
 	ret = media_entity_pads_init(&vfd->entity, 1, &vp->pad);
 	if (ret)
-		goto err_vd_rel;
+		return ret;
 
 	video_set_drvdata(vfd, vp);
 
@@ -1170,8 +1170,6 @@
 	v4l2_ctrl_handler_free(&vp->ctrl_handler);
 err_me_cleanup:
 	media_entity_cleanup(&vfd->entity);
-err_vd_rel:
-	video_device_release(vfd);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s3c-camif/camif-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s3c-camif/camif-core.c
@@ -532,10 +532,19 @@
 static int s3c_camif_runtime_resume(struct device *dev)
 {
 	struct camif_dev *camif = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(camif->clock[CLK_GATE]);
+	if (ret)
+		return ret;
 
-	clk_enable(camif->clock[CLK_GATE]);
 	/* null op on s3c244x */
-	clk_enable(camif->clock[CLK_CAM]);
+	ret = clk_enable(camif->clock[CLK_CAM]);
+	if (ret) {
+		clk_disable(camif->clock[CLK_GATE]);
+		return ret;
+	}
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s5p-jpeg/jpeg-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s5p-jpeg/jpeg-core.c
@@ -775,11 +775,14 @@
 		(unsigned long)vb2_plane_vaddr(&vb->vb2_buf, 0) + ctx->out_q.sos + 2;
 	jpeg_buffer.curr = 0;
 
-	word = 0;
-
 	if (get_word_be(&jpeg_buffer, &word))
 		return;
-	jpeg_buffer.size = (long)word - 2;
+
+	if (word < 2)
+		jpeg_buffer.size = 0;
+	else
+		jpeg_buffer.size = (long)word - 2;
+
 	jpeg_buffer.data += 2;
 	jpeg_buffer.curr = 0;
 
@@ -1058,6 +1061,7 @@
 	if (byte == -1)
 		return -1;
 	*word = (unsigned int)byte | temp;
+
 	return 0;
 }
 
@@ -1145,7 +1149,7 @@
 			if (get_word_be(&jpeg_buffer, &word))
 				break;
 			length = (long)word - 2;
-			if (!length)
+			if (length <= 0)
 				return false;
 			sof = jpeg_buffer.curr; /* after 0xffc0 */
 			sof_len = length;
@@ -1176,7 +1180,7 @@
 			if (get_word_be(&jpeg_buffer, &word))
 				break;
 			length = (long)word - 2;
-			if (!length)
+			if (length <= 0)
 				return false;
 			if (n_dqt >= S5P_JPEG_MAX_MARKER)
 				return false;
@@ -1189,7 +1193,7 @@
 			if (get_word_be(&jpeg_buffer, &word))
 				break;
 			length = (long)word - 2;
-			if (!length)
+			if (length <= 0)
 				return false;
 			if (n_dht >= S5P_JPEG_MAX_MARKER)
 				return false;
@@ -1214,6 +1218,7 @@
 			if (get_word_be(&jpeg_buffer, &word))
 				break;
 			length = (long)word - 2;
+			/* No need to check underflows as skip() does it  */
 			skip(&jpeg_buffer, length);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s5p-mfc/s5p_mfc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s5p-mfc/s5p_mfc.c
@@ -1283,11 +1283,15 @@
 	spin_lock_init(&dev->condlock);
 	dev->plat_dev = pdev;
 	if (!dev->plat_dev) {
-		dev_err(&pdev->dev, "No platform data specified\n");
+		mfc_err("No platform data specified\n");
 		return -ENODEV;
 	}
 
 	dev->variant = of_device_get_match_data(&pdev->dev);
+	if (!dev->variant) {
+		dev_err(&pdev->dev, "Failed to get device MFC hardware variant information\n");
+		return -ENOENT;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dev->regs_base = devm_ioremap_resource(&pdev->dev, res);
@@ -1402,6 +1406,7 @@
 /* Deinit MFC if probe had failed */
 err_enc_reg:
 	video_unregister_device(dev->vfd_dec);
+	dev->vfd_dec = NULL;
 err_dec_reg:
 	video_device_release(dev->vfd_enc);
 err_enc_alloc:
@@ -1447,8 +1452,6 @@
 
 	video_unregister_device(dev->vfd_enc);
 	video_unregister_device(dev->vfd_dec);
-	video_device_release(dev->vfd_enc);
-	video_device_release(dev->vfd_dec);
 	v4l2_device_unregister(&dev->v4l2_dev);
 	s5p_mfc_unconfigure_dma_memory(dev);
 
@@ -1580,8 +1583,18 @@
 	.port_num	= MFC_NUM_PORTS_V7,
 	.buf_size	= &buf_size_v7,
 	.fw_name[0]     = "s5p-mfc-v7.fw",
-	.clk_names	= {"mfc", "sclk_mfc"},
-	.num_clocks	= 2,
+	.clk_names	= {"mfc"},
+	.num_clocks	= 1,
+};
+
+static struct s5p_mfc_variant mfc_drvdata_v7_3250 = {
+	.version        = MFC_VERSION_V7,
+	.version_bit    = MFC_V7_BIT,
+	.port_num       = MFC_NUM_PORTS_V7,
+	.buf_size       = &buf_size_v7,
+	.fw_name[0]     = "s5p-mfc-v7.fw",
+	.clk_names      = {"mfc", "sclk_mfc"},
+	.num_clocks     = 2,
 };
 
 static struct s5p_mfc_buf_size_v6 mfc_buf_size_v8 = {
@@ -1652,6 +1665,9 @@
 		.compatible = "samsung,mfc-v7",
 		.data = &mfc_drvdata_v7,
 	}, {
+		.compatible = "samsung,exynos3250-mfc",
+		.data = &mfc_drvdata_v7_3250,
+	}, {
 		.compatible = "samsung,mfc-v8",
 		.data = &mfc_drvdata_v8,
 	}, {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s5p-mfc/s5p_mfc_ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s5p-mfc/s5p_mfc_ctrl.c
@@ -468,8 +468,10 @@
 	s5p_mfc_hw_call(dev->mfc_ops, try_run, dev);
 	/* Wait until instance is returned or timeout occurred */
 	if (s5p_mfc_wait_for_done_ctx(ctx,
-				S5P_MFC_R2H_CMD_CLOSE_INSTANCE_RET, 0))
+				S5P_MFC_R2H_CMD_CLOSE_INSTANCE_RET, 0)){
+		clear_work_bit_irqsave(ctx);
 		mfc_err("Err returning instance\n");
+	}
 
 	/* Free resources */
 	s5p_mfc_hw_call(dev->mfc_ops, release_codec_buffers, ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s5p-mfc/s5p_mfc_enc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s5p-mfc/s5p_mfc_enc.c
@@ -1218,6 +1218,7 @@
 	unsigned long mb_y_addr, mb_c_addr;
 	int slice_type;
 	unsigned int strm_size;
+	bool src_ready;
 
 	slice_type = s5p_mfc_hw_call(dev->mfc_ops, get_enc_slice_type, dev);
 	strm_size = s5p_mfc_hw_call(dev->mfc_ops, get_enc_strm_size, dev);
@@ -1257,7 +1258,8 @@
 			}
 		}
 	}
-	if ((ctx->src_queue_cnt > 0) && (ctx->state == MFCINST_RUNNING)) {
+	if (ctx->src_queue_cnt > 0 && (ctx->state == MFCINST_RUNNING ||
+				       ctx->state == MFCINST_FINISHING)) {
 		mb_entry = list_entry(ctx->src_queue.next, struct s5p_mfc_buf,
 									list);
 		if (mb_entry->flags & MFC_BUF_FLAG_USED) {
@@ -1288,7 +1290,13 @@
 		vb2_set_plane_payload(&mb_entry->b->vb2_buf, 0, strm_size);
 		vb2_buffer_done(&mb_entry->b->vb2_buf, VB2_BUF_STATE_DONE);
 	}
-	if ((ctx->src_queue_cnt == 0) || (ctx->dst_queue_cnt == 0))
+
+	src_ready = true;
+	if (ctx->state == MFCINST_RUNNING && ctx->src_queue_cnt == 0)
+		src_ready = false;
+	if (ctx->state == MFCINST_FINISHING && ctx->ref_queue_cnt == 0)
+		src_ready = false;
+	if (!src_ready || ctx->dst_queue_cnt == 0)
 		clear_work_bit(ctx);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/s5p-mfc/s5p_mfc_opr_v6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/s5p-mfc/s5p_mfc_opr_v6.c
@@ -1060,7 +1060,7 @@
 	}
 
 	/* aspect ratio VUI */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x1 << 5);
 	reg |= ((p_h264->vui_sar & 0x1) << 5);
 	writel(reg, mfc_regs->e_h264_options);
@@ -1083,7 +1083,7 @@
 
 	/* intra picture period for H.264 open GOP */
 	/* control */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x1 << 4);
 	reg |= ((p_h264->open_gop & 0x1) << 4);
 	writel(reg, mfc_regs->e_h264_options);
@@ -1097,23 +1097,23 @@
 	}
 
 	/* 'WEIGHTED_BI_PREDICTION' for B is disable */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x3 << 9);
 	writel(reg, mfc_regs->e_h264_options);
 
 	/* 'CONSTRAINED_INTRA_PRED_ENABLE' is disable */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x1 << 14);
 	writel(reg, mfc_regs->e_h264_options);
 
 	/* ASO */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x1 << 6);
 	reg |= ((p_h264->aso & 0x1) << 6);
 	writel(reg, mfc_regs->e_h264_options);
 
 	/* hier qp enable */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x1 << 8);
 	reg |= ((p_h264->open_gop & 0x1) << 8);
 	writel(reg, mfc_regs->e_h264_options);
@@ -1134,7 +1134,7 @@
 	writel(reg, mfc_regs->e_h264_num_t_layer);
 
 	/* frame packing SEI generation */
-	readl(mfc_regs->e_h264_options);
+	reg = readl(mfc_regs->e_h264_options);
 	reg &= ~(0x1 << 25);
 	reg |= ((p_h264->sei_frame_packing & 0x1) << 25);
 	writel(reg, mfc_regs->e_h264_options);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/sti/bdisp/bdisp-v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/sti/bdisp/bdisp-v4l2.c
@@ -1310,6 +1310,8 @@
 	init_waitqueue_head(&bdisp->irq_queue);
 	INIT_DELAYED_WORK(&bdisp->timeout_work, bdisp_irq_timeout);
 	bdisp->work_queue = create_workqueue(BDISP_NAME);
+	if (!bdisp->work_queue)
+		return -ENOMEM;
 
 	spin_lock_init(&bdisp->slock);
 	mutex_init(&bdisp->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c
@@ -940,6 +940,7 @@
 		if (ret) {
 			dev_err(fei->dev,
 				"configure_memdma_and_inputblock failed\n");
+			of_node_put(child);
 			goto err_unmap;
 		}
 		index++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/sti/delta/delta-v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/sti/delta/delta-v4l2.c
@@ -1859,7 +1859,7 @@
 	if (ret) {
 		dev_err(delta->dev, "%s failed to initialize firmware ipc channel\n",
 			DELTA_PREFIX);
-		goto err;
+		goto err_pm_disable;
 	}
 
 	/* register all available decoders */
@@ -1873,7 +1873,7 @@
 	if (ret) {
 		dev_err(delta->dev, "%s failed to register V4L2 device\n",
 			DELTA_PREFIX);
-		goto err;
+		goto err_pm_disable;
 	}
 
 	delta->work_queue = create_workqueue(DELTA_NAME);
@@ -1898,6 +1898,8 @@
 	destroy_workqueue(delta->work_queue);
 err_v4l2:
 	v4l2_device_unregister(&delta->v4l2_dev);
+err_pm_disable:
+	pm_runtime_disable(dev);
 err:
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/stm32/stm32-dcmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/stm32/stm32-dcmi.c
@@ -128,6 +128,7 @@
 	int				sequence;
 	struct list_head		buffers;
 	struct dcmi_buf			*active;
+	int			irq;
 
 	struct v4l2_device		v4l2_dev;
 	struct video_device		*vdev;
@@ -1759,6 +1760,14 @@
 		return ret;
 	}
 
+	ret = devm_request_threaded_irq(dcmi->dev, dcmi->irq, dcmi_irq_callback,
+					dcmi_irq_thread, IRQF_ONESHOT,
+					dev_name(dcmi->dev), dcmi);
+	if (ret) {
+		dev_err(dcmi->dev, "Unable to request irq %d\n", dcmi->irq);
+		return ret;
+	}
+
 	return 0;
 }
 
@@ -1914,6 +1923,8 @@
 	if (irq <= 0)
 		return irq ? irq : -ENXIO;
 
+	dcmi->irq = irq;
+
 	dcmi->res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!dcmi->res) {
 		dev_err(&pdev->dev, "Could not get resource\n");
@@ -1926,14 +1937,6 @@
 		return PTR_ERR(dcmi->regs);
 	}
 
-	ret = devm_request_threaded_irq(&pdev->dev, irq, dcmi_irq_callback,
-					dcmi_irq_thread, IRQF_ONESHOT,
-					dev_name(&pdev->dev), dcmi);
-	if (ret) {
-		dev_err(&pdev->dev, "Unable to request irq %d\n", irq);
-		return ret;
-	}
-
 	mclk = devm_clk_get(&pdev->dev, "mclk");
 	if (IS_ERR(mclk)) {
 		if (PTR_ERR(mclk) != -EPROBE_DEFER)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/sunxi/sun4i-csi/sun4i_csi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/sunxi/sun4i-csi/sun4i_csi.c
@@ -40,6 +40,10 @@
 	.link_validate = v4l2_subdev_link_validate,
 };
 
+static const struct media_entity_operations sun4i_csi_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
 static int sun4i_csi_notify_bound(struct v4l2_async_notifier *notifier,
 				  struct v4l2_subdev *subdev,
 				  struct v4l2_async_subdev *asd)
@@ -218,6 +222,7 @@
 	v4l2_subdev_init(subdev, &sun4i_csi_subdev_ops);
 	subdev->flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
 	subdev->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+	subdev->entity.ops = &sun4i_csi_subdev_entity_ops;
 	subdev->owner = THIS_MODULE;
 	snprintf(subdev->name, sizeof(subdev->name), "sun4i-csi-0");
 	v4l2_set_subdevdata(subdev, csi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/sunxi/sun6i-csi/sun6i_video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/sunxi/sun6i-csi/sun6i_video.c
@@ -467,7 +467,7 @@
 static int sun6i_video_open(struct file *file)
 {
 	struct sun6i_video *video = video_drvdata(file);
-	int ret;
+	int ret = 0;
 
 	if (mutex_lock_interruptible(&video->lock))
 		return -ERESTARTSYS;
@@ -481,10 +481,8 @@
 		goto fh_release;
 
 	/* check if already powered */
-	if (!v4l2_fh_is_singular_file(file)) {
-		ret = -EBUSY;
+	if (!v4l2_fh_is_singular_file(file))
 		goto unlock;
-	}
 
 	ret = sun6i_csi_set_power(video->csi, true);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/sunxi/sun8i-di/sun8i-di.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/sunxi/sun8i-di/sun8i-di.c
@@ -66,6 +66,7 @@
 	struct vb2_v4l2_buffer *src, *dst;
 	unsigned int hstep, vstep;
 	dma_addr_t addr;
+	int i;
 
 	src = v4l2_m2m_next_src_buf(ctx->fh.m2m_ctx);
 	dst = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx);
@@ -160,6 +161,26 @@
 	deinterlace_write(dev, DEINTERLACE_CH1_HORZ_FACT, hstep);
 	deinterlace_write(dev, DEINTERLACE_CH1_VERT_FACT, vstep);
 
+	/* neutral filter coefficients */
+	deinterlace_set_bits(dev, DEINTERLACE_FRM_CTRL,
+			     DEINTERLACE_FRM_CTRL_COEF_ACCESS);
+	readl_poll_timeout(dev->base + DEINTERLACE_STATUS, val,
+			   val & DEINTERLACE_STATUS_COEF_STATUS, 2, 40);
+
+	for (i = 0; i < 32; i++) {
+		deinterlace_write(dev, DEINTERLACE_CH0_HORZ_COEF0 + i * 4,
+				  DEINTERLACE_IDENTITY_COEF);
+		deinterlace_write(dev, DEINTERLACE_CH0_VERT_COEF + i * 4,
+				  DEINTERLACE_IDENTITY_COEF);
+		deinterlace_write(dev, DEINTERLACE_CH1_HORZ_COEF0 + i * 4,
+				  DEINTERLACE_IDENTITY_COEF);
+		deinterlace_write(dev, DEINTERLACE_CH1_VERT_COEF + i * 4,
+				  DEINTERLACE_IDENTITY_COEF);
+	}
+
+	deinterlace_clr_set_bits(dev, DEINTERLACE_FRM_CTRL,
+				 DEINTERLACE_FRM_CTRL_COEF_ACCESS, 0);
+
 	deinterlace_clr_set_bits(dev, DEINTERLACE_FIELD_CTRL,
 				 DEINTERLACE_FIELD_CTRL_FIELD_CNT_MSK,
 				 DEINTERLACE_FIELD_CTRL_FIELD_CNT(ctx->field));
@@ -248,7 +269,6 @@
 static void deinterlace_init(struct deinterlace_dev *dev)
 {
 	u32 val;
-	int i;
 
 	deinterlace_write(dev, DEINTERLACE_BYPASS,
 			  DEINTERLACE_BYPASS_CSC);
@@ -284,27 +304,7 @@
 
 	deinterlace_clr_set_bits(dev, DEINTERLACE_CHROMA_DIFF,
 				 DEINTERLACE_CHROMA_DIFF_TH_MSK,
-				 DEINTERLACE_CHROMA_DIFF_TH(5));
-
-	/* neutral filter coefficients */
-	deinterlace_set_bits(dev, DEINTERLACE_FRM_CTRL,
-			     DEINTERLACE_FRM_CTRL_COEF_ACCESS);
-	readl_poll_timeout(dev->base + DEINTERLACE_STATUS, val,
-			   val & DEINTERLACE_STATUS_COEF_STATUS, 2, 40);
-
-	for (i = 0; i < 32; i++) {
-		deinterlace_write(dev, DEINTERLACE_CH0_HORZ_COEF0 + i * 4,
-				  DEINTERLACE_IDENTITY_COEF);
-		deinterlace_write(dev, DEINTERLACE_CH0_VERT_COEF + i * 4,
-				  DEINTERLACE_IDENTITY_COEF);
-		deinterlace_write(dev, DEINTERLACE_CH1_HORZ_COEF0 + i * 4,
-				  DEINTERLACE_IDENTITY_COEF);
-		deinterlace_write(dev, DEINTERLACE_CH1_VERT_COEF + i * 4,
-				  DEINTERLACE_IDENTITY_COEF);
-	}
-
-	deinterlace_clr_set_bits(dev, DEINTERLACE_FRM_CTRL,
-				 DEINTERLACE_FRM_CTRL_COEF_ACCESS, 0);
+				 DEINTERLACE_CHROMA_DIFF_TH(31));
 }
 
 static inline struct deinterlace_ctx *deinterlace_file2ctx(struct file *file)
@@ -933,11 +933,18 @@
 		return ret;
 	}
 
+	ret = reset_control_deassert(dev->rstc);
+	if (ret) {
+		dev_err(dev->dev, "Failed to apply reset\n");
+
+		goto err_exclusive_rate;
+	}
+
 	ret = clk_prepare_enable(dev->bus_clk);
 	if (ret) {
 		dev_err(dev->dev, "Failed to enable bus clock\n");
 
-		goto err_exclusive_rate;
+		goto err_rst;
 	}
 
 	ret = clk_prepare_enable(dev->mod_clk);
@@ -954,23 +961,16 @@
 		goto err_mod_clk;
 	}
 
-	ret = reset_control_deassert(dev->rstc);
-	if (ret) {
-		dev_err(dev->dev, "Failed to apply reset\n");
-
-		goto err_ram_clk;
-	}
-
 	deinterlace_init(dev);
 
 	return 0;
 
-err_ram_clk:
-	clk_disable_unprepare(dev->ram_clk);
 err_mod_clk:
 	clk_disable_unprepare(dev->mod_clk);
 err_bus_clk:
 	clk_disable_unprepare(dev->bus_clk);
+err_rst:
+	reset_control_assert(dev->rstc);
 err_exclusive_rate:
 	clk_rate_exclusive_put(dev->mod_clk);
 
@@ -981,11 +981,12 @@
 {
 	struct deinterlace_dev *dev = dev_get_drvdata(device);
 
-	reset_control_assert(dev->rstc);
-
 	clk_disable_unprepare(dev->ram_clk);
 	clk_disable_unprepare(dev->mod_clk);
 	clk_disable_unprepare(dev->bus_clk);
+
+	reset_control_assert(dev->rstc);
+
 	clk_rate_exclusive_put(dev->mod_clk);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/ti-vpe/cal-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/ti-vpe/cal-video.c
@@ -814,7 +814,6 @@
 
 static int cal_ctx_v4l2_init_formats(struct cal_ctx *ctx)
 {
-	struct v4l2_subdev_mbus_code_enum mbus_code;
 	struct v4l2_mbus_framefmt mbus_fmt;
 	const struct cal_format_info *fmtinfo;
 	unsigned int i, j, k;
@@ -823,13 +822,17 @@
 	/* Enumerate sub device formats and enable all matching local formats */
 	ctx->active_fmt = devm_kcalloc(ctx->cal->dev, cal_num_formats,
 				       sizeof(*ctx->active_fmt), GFP_KERNEL);
+	if (!ctx->active_fmt)
+		return -ENOMEM;
+
 	ctx->num_active_fmt = 0;
 
 	for (j = 0, i = 0; ; ++j) {
+		struct v4l2_subdev_mbus_code_enum mbus_code = {
+			.index = j,
+			.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		};
 
-		memset(&mbus_code, 0, sizeof(mbus_code));
-		mbus_code.index = j;
-		mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 		ret = v4l2_subdev_call(ctx->phy->source, pad, enum_mbus_code,
 				       NULL, &mbus_code);
 		if (ret == -EINVAL)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/ti-vpe/cal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/ti-vpe/cal.c
@@ -940,8 +940,10 @@
 	ctx->datatype = CAL_CSI2_CTX_DT_ANY;
 
 	ret = cal_ctx_v4l2_init(ctx);
-	if (ret)
+	if (ret) {
+		kfree(ctx);
 		return NULL;
+	}
 
 	return ctx;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/vsp1/vsp1_drm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/vsp1/vsp1_drm.c
@@ -66,7 +66,9 @@
 			      struct vsp1_entity *prev, unsigned int prev_pad,
 			      struct vsp1_entity *next, unsigned int next_pad)
 {
-	struct v4l2_subdev_format format;
+	struct v4l2_subdev_format format = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
 	int ret;
 
 	if (!uif) {
@@ -82,8 +84,6 @@
 	prev->sink = uif;
 	prev->sink_pad = UIF_PAD_SINK;
 
-	memset(&format, 0, sizeof(format));
-	format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	format.pad = prev_pad;
 
 	ret = v4l2_subdev_call(&prev->subdev, pad, get_fmt, NULL, &format);
@@ -118,8 +118,12 @@
 				      struct vsp1_entity *uif,
 				      unsigned int brx_input)
 {
-	struct v4l2_subdev_selection sel;
-	struct v4l2_subdev_format format;
+	struct v4l2_subdev_selection sel = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
+	struct v4l2_subdev_format format = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
 	const struct v4l2_rect *crop;
 	int ret;
 
@@ -129,8 +133,6 @@
 	 */
 	crop = &vsp1->drm->inputs[rpf->entity.index].crop;
 
-	memset(&format, 0, sizeof(format));
-	format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	format.pad = RWPF_PAD_SINK;
 	format.format.width = crop->width + crop->left;
 	format.format.height = crop->height + crop->top;
@@ -147,8 +149,6 @@
 		__func__, format.format.width, format.format.height,
 		format.format.code, rpf->entity.index);
 
-	memset(&sel, 0, sizeof(sel));
-	sel.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	sel.pad = RWPF_PAD_SINK;
 	sel.target = V4L2_SEL_TGT_CROP;
 	sel.r = *crop;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/vsp1/vsp1_entity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/vsp1/vsp1_entity.c
@@ -184,15 +184,14 @@
 int vsp1_entity_init_cfg(struct v4l2_subdev *subdev,
 			 struct v4l2_subdev_state *sd_state)
 {
-	struct v4l2_subdev_format format;
 	unsigned int pad;
 
 	for (pad = 0; pad < subdev->entity.num_pads - 1; ++pad) {
-		memset(&format, 0, sizeof(format));
-
-		format.pad = pad;
-		format.which = sd_state ? V4L2_SUBDEV_FORMAT_TRY
-			     : V4L2_SUBDEV_FORMAT_ACTIVE;
+		struct v4l2_subdev_format format = {
+			.pad = pad,
+			.which = sd_state ? V4L2_SUBDEV_FORMAT_TRY
+			       : V4L2_SUBDEV_FORMAT_ACTIVE,
+		};
 
 		v4l2_subdev_call(subdev, pad, set_fmt, sd_state, &format);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/vsp1/vsp1_histo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/vsp1/vsp1_histo.c
@@ -36,9 +36,8 @@
 vsp1_histogram_buffer_get(struct vsp1_histogram *histo)
 {
 	struct vsp1_histogram_buffer *buf = NULL;
-	unsigned long flags;
 
-	spin_lock_irqsave(&histo->irqlock, flags);
+	spin_lock(&histo->irqlock);
 
 	if (list_empty(&histo->irqqueue))
 		goto done;
@@ -49,7 +48,7 @@
 	histo->readout = true;
 
 done:
-	spin_unlock_irqrestore(&histo->irqlock, flags);
+	spin_unlock(&histo->irqlock);
 	return buf;
 }
 
@@ -58,7 +57,6 @@
 				    size_t size)
 {
 	struct vsp1_pipeline *pipe = histo->entity.pipe;
-	unsigned long flags;
 
 	/*
 	 * The pipeline pointer is guaranteed to be valid as this function is
@@ -70,10 +68,10 @@
 	vb2_set_plane_payload(&buf->buf.vb2_buf, 0, size);
 	vb2_buffer_done(&buf->buf.vb2_buf, VB2_BUF_STATE_DONE);
 
-	spin_lock_irqsave(&histo->irqlock, flags);
+	spin_lock(&histo->irqlock);
 	histo->readout = false;
 	wake_up(&histo->wait_queue);
-	spin_unlock_irqrestore(&histo->irqlock, flags);
+	spin_unlock(&histo->irqlock);
 }
 
 /* -----------------------------------------------------------------------------
@@ -124,11 +122,10 @@
 	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
 	struct vsp1_histogram *histo = vb2_get_drv_priv(vb->vb2_queue);
 	struct vsp1_histogram_buffer *buf = to_vsp1_histogram_buffer(vbuf);
-	unsigned long flags;
 
-	spin_lock_irqsave(&histo->irqlock, flags);
+	spin_lock_irq(&histo->irqlock);
 	list_add_tail(&buf->queue, &histo->irqqueue);
-	spin_unlock_irqrestore(&histo->irqlock, flags);
+	spin_unlock_irq(&histo->irqlock);
 }
 
 static int histo_start_streaming(struct vb2_queue *vq, unsigned int count)
@@ -140,9 +137,8 @@
 {
 	struct vsp1_histogram *histo = vb2_get_drv_priv(vq);
 	struct vsp1_histogram_buffer *buffer;
-	unsigned long flags;
 
-	spin_lock_irqsave(&histo->irqlock, flags);
+	spin_lock_irq(&histo->irqlock);
 
 	/* Remove all buffers from the IRQ queue. */
 	list_for_each_entry(buffer, &histo->irqqueue, queue)
@@ -152,7 +148,7 @@
 	/* Wait for the buffer being read out (if any) to complete. */
 	wait_event_lock_irq(histo->wait_queue, !histo->readout, histo->irqlock);
 
-	spin_unlock_irqrestore(&histo->irqlock, flags);
+	spin_unlock_irq(&histo->irqlock);
 }
 
 static const struct vb2_ops histo_video_queue_qops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/vsp1/vsp1_pipe.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/vsp1/vsp1_pipe.h
@@ -73,7 +73,7 @@
  * @wpf: The WPF partition window configuration
  */
 struct vsp1_partition {
-	struct vsp1_partition_window rpf;
+	struct vsp1_partition_window rpf[VSP1_MAX_RPF];
 	struct vsp1_partition_window uds_sink;
 	struct vsp1_partition_window uds_source;
 	struct vsp1_partition_window sru;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/vsp1/vsp1_rpf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/vsp1/vsp1_rpf.c
@@ -271,8 +271,8 @@
 	 * 'width' need to be adjusted.
 	 */
 	if (pipe->partitions > 1) {
-		crop.width = pipe->partition->rpf.width;
-		crop.left += pipe->partition->rpf.left;
+		crop.width = pipe->partition->rpf[rpf->entity.index].width;
+		crop.left += pipe->partition->rpf[rpf->entity.index].left;
 	}
 
 	if (pipe->interlaced) {
@@ -291,11 +291,11 @@
 		     + crop.left * fmtinfo->bpp[0] / 8;
 
 	if (format->num_planes > 1) {
+		unsigned int bpl = format->plane_fmt[1].bytesperline;
 		unsigned int offset;
 
-		offset = crop.top * format->plane_fmt[1].bytesperline
-		       + crop.left / fmtinfo->hsub
-		       * fmtinfo->bpp[1] / 8;
+		offset = crop.top / fmtinfo->vsub * bpl
+		       + crop.left / fmtinfo->hsub * fmtinfo->bpp[1] / 8;
 		mem.addr[1] += offset;
 		mem.addr[2] += offset;
 	}
@@ -327,7 +327,9 @@
 			  unsigned int partition_idx,
 			  struct vsp1_partition_window *window)
 {
-	partition->rpf = *window;
+	struct vsp1_rwpf *rpf = to_rwpf(&entity->subdev);
+
+	partition->rpf[rpf->entity.index] = *window;
 }
 
 static const struct vsp1_entity_operations rpf_entity_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/Kconfig
@@ -3,9 +3,11 @@
 config VIDEO_XILINX
 	tristate "Xilinx Video IP (EXPERIMENTAL)"
 	depends on VIDEO_V4L2  && OF && HAS_DMA
+	depends on DMADEVICES
 	select MEDIA_CONTROLLER
 	select VIDEO_V4L2_SUBDEV_API
 	select VIDEOBUF2_DMA_CONTIG
+	select XILINX_FRMBUF
 	select V4L2_FWNODE
 	help
 	  Driver for Xilinx Video IP Pipelines
@@ -19,17 +21,180 @@
 	  based driver that takes input from CSI-2 Tx source and converts
 	  it into an AXI4-Stream.
 
+config VIDEO_XILINX_AXI4S_SWITCH
+	tristate "Xilinx AXI4-Stream Video Switch"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx AXI4-Stream Video Switch. This is a
+	  V4L sub device based driver. It supports fixed (TDEST based)
+	  as well as dynamic (control register based) routing.
+	  Say M to modularize. Say N if unsure.
+
+config VIDEO_XILINX_CFA
+	tristate "Xilinx Video Color Filter Array"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Color Filter Array
+
+config VIDEO_XILINX_CRESAMPLE
+	tristate "Xilinx Video Chroma Resampler"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Chroma Resampler
+
+config VIDEO_XILINX_DEMOSAIC
+	tristate "Xilinx Video Demosaic IP"
+	depends on VIDEO_XILINX
+	help
+	  Driver for Xilinx Video Demosaic IP. This is a V4L sub-device
+	  based driver for the Demosaic IP that takes input a Bayer video
+	  stream format as input and generates an RGB video output.
+	  Say M to modularize. Say N if unsure.
+
+config VIDEO_XILINX_GAMMA
+	tristate "Xilinx Gamma Correction LUT"
+	depends on VIDEO_XILINX
+	help
+	  Driver for Xilinx Gamma Correction LUT IP. This is a V4L sub-device
+	  based driver that exposes V4L controls to adjust Red, Blue and Green
+	  Gamma Correction.
+
+	  Say M to modularize. Say N if unsure.
+
+config VIDEO_XILINX_HDMI21RXSS
+	tristate "Xilinx HDMI 2.1 Rx Subsystem"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx HDMI 2.1 Rx subsystem to capture HDMI streams.
+	  This is a V4L2 subdev driver which used to get the stream properties
+	  like timing, color format and depth, frame rate.
+
+	  Say M to modularize. Say N if unsure.
+
+config VIDEO_XILINX_HLS
+	tristate "Xilinx Video HLS Core"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Video HLS Cores
+
+config VIDEO_XILINX_REMAPPER
+	tristate "Xilinx Video Remapper"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Video Remapper
+
+config VIDEO_XILINX_RGB2YUV
+	tristate "Xilinx Video RGB to YUV Convertor"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Video RGB to YUV Convertor
+
+config VIDEO_XILINX_SCALER
+	tristate "Xilinx Video Scaler"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Video Scaler
+
+config VIDEO_XILINX_MULTISCALER
+	tristate "Xilinx Video Multiscaler"
+	depends on VIDEO_XILINX
+	depends on VIDEO_DEV && VIDEO_V4L2
+	select V4L2_MEM2MEM_DEV
+	select VIDEOBUF2_DMA_CONTIG
+	help
+	  Driver for the Xilinx Video Multi Scaler. This is a V4L2 memory to
+	  memory based driver. Multi-Scaler has max 8 channels which can be
+	  programed for different scaling ratio.
+
+config VIDEO_XILINX_SDIRXSS
+	tristate "Xilinx SDI Rx Subsystem"
+	depends on VIDEO_XILINX
+	help
+	  Driver for Xilinx SDI Rx Subsystem
+
+config VIDEO_XILINX_SWITCH
+	tristate "Xilinx Video Switch"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Video Switch
+
 config VIDEO_XILINX_TPG
 	tristate "Xilinx Video Test Pattern Generator"
 	depends on VIDEO_XILINX
 	select VIDEO_XILINX_VTC
 	help
-	   Driver for the Xilinx Video Test Pattern Generator
+	  Driver for the Xilinx Video Test Pattern Generator
+
+config VIDEO_XILINX_VPSS_CSC
+	tristate "Xilinx VPSS CSC"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx Video Processing Sub-System (VPSS)
+	  Color Space Conversion. The driver provides RGB to YUV444
+	  conversion and provides video controls like Brightness,
+	  Contrast, Color Gains that can be applied to video.
+	  Say N if unsure. Say M to modularize.
+
+config VIDEO_XILINX_VPSS_SCALER
+	tristate "Xilinx Video VPSS Scaler"
+	depends on VIDEO_XILINX
+	help
+	  Driver for Xilinx Video Processing Sub-System(VPSS) Scaler.
+	  It allows upscaling and downscaling of video. It also supports
+	  limited Color Space Conversion.
+	  Say N if unsure.
 
 config VIDEO_XILINX_VTC
 	tristate "Xilinx Video Timing Controller"
 	depends on VIDEO_XILINX
 	help
-	   Driver for the Xilinx Video Timing Controller
+	  Driver for the Xilinx Video Timing Controller
+
+config VIDEO_XILINX_DPRXSS
+	tristate "Xilinx DP Rx Subsystem"
+	depends on VIDEO_XILINX
+	help
+	  Driver for Xilinx DisplayPort Rx Subsystem. This is a V4L sub-device
+	  based driver for the DisplayPort receiver subsystem IP. It captures
+	  AXI-Stream video data and output to video IPs. Choose this driver
+	  in a platform where the DisplayPort rx subsystem can be instantiated.
+
+config VIDEO_XILINX_SCD
+	tristate "Xilinx Scene Change Detect"
+	depends on VIDEO_XILINX
+	help
+	  Driver for Xilinx Scene Change Detection Controller.
+	  The driver allows applications to pass video buffers and
+	  provides if scene change detection is present between
+	  adjacent frames.
+
+config VIDEO_XILINX_M2M
+	tristate "Xilinx Video mem2mem"
+	depends on VIDEO_XILINX
+	select V4L2_MEM2MEM_DEV
+	help
+	  Driver for Xilinx V4L2 mem2mem pipeline operation to achieve memory
+	  copy between two different physical memories using DMA transfers.
+
+config VIDEO_XILINX_AXI4S_BROADCASTER
+	tristate "Xilinx AXI4-Stream Video Broadcaster"
+	depends on VIDEO_XILINX
+	help
+	  Driver for the Xilinx AXI4-Stream Video Broadcaster. This is a
+	  V4L sub device based driver. It replicates a single input AXI4-Stream
+	  into multiple output AXI4-Stream.
+	  Say M to modularize. Say N if unsure.
+
+config VIDEO_XILINX_AXI4S_SUBSETCONV
+	tristate "Xilinx AXI4-Stream Subset Converter"
+	depends on VIDEO_XILINX
+	help
+	  This subset converter driver is for configuring the Xilinx
+	  subset converter IP which is a non-memory mapped IP used for
+	  converting formats. The format conversion of source pad and
+	  sink pad in the pipeline done by subset conveter IP will be
+	  mapped in this driver.
+	  To compile this driver as a module, choose M here.
+	  If unsure, choose N
 
 endif #VIDEO_XILINX
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/Makefile
@@ -1,8 +1,30 @@
 # SPDX-License-Identifier: GPL-2.0
 
+xilinx-scd-objs += xilinx-scenechange.o xilinx-scenechange-channel.o \
+		   xilinx-scenechange-dma.o
 xilinx-video-objs += xilinx-dma.o xilinx-vip.o xilinx-vipp.o
 
 obj-$(CONFIG_VIDEO_XILINX) += xilinx-video.o
+obj-$(CONFIG_VIDEO_XILINX_AXI4S_BROADCASTER) += xilinx-axis-broadcaster.o
+obj-$(CONFIG_VIDEO_XILINX_AXI4S_SUBSETCONV) += xilinx-axis-subsetconv.o
+obj-$(CONFIG_VIDEO_XILINX_AXI4S_SWITCH) += xilinx-axis-switch.o
+obj-$(CONFIG_VIDEO_XILINX_CFA) += xilinx-cfa.o
+obj-$(CONFIG_VIDEO_XILINX_CRESAMPLE) += xilinx-cresample.o
 obj-$(CONFIG_VIDEO_XILINX_CSI2RXSS) += xilinx-csi2rxss.o
+obj-$(CONFIG_VIDEO_XILINX_DEMOSAIC) += xilinx-demosaic.o
+obj-$(CONFIG_VIDEO_XILINX_DPRXSS) += xilinx-dprxss.o
+obj-$(CONFIG_VIDEO_XILINX_GAMMA) += xilinx-gamma.o
+obj-$(CONFIG_VIDEO_XILINX_HDMI21RXSS) += xilinx-hdmirxss.o
+obj-$(CONFIG_VIDEO_XILINX_HLS) += xilinx-hls.o
+obj-$(CONFIG_VIDEO_XILINX_M2M) += xilinx-m2m.o
+obj-$(CONFIG_VIDEO_XILINX_MULTISCALER) += xilinx-multi-scaler.o
+obj-$(CONFIG_VIDEO_XILINX_REMAPPER) += xilinx-remapper.o
+obj-$(CONFIG_VIDEO_XILINX_RGB2YUV) += xilinx-rgb2yuv.o
+obj-$(CONFIG_VIDEO_XILINX_SCALER) += xilinx-scaler.o
+obj-$(CONFIG_VIDEO_XILINX_SCD) += xilinx-scd.o
+obj-$(CONFIG_VIDEO_XILINX_SDIRXSS) += xilinx-sdirxss.o
+obj-$(CONFIG_VIDEO_XILINX_SWITCH) += xilinx-switch.o
 obj-$(CONFIG_VIDEO_XILINX_TPG) += xilinx-tpg.o
+obj-$(CONFIG_VIDEO_XILINX_VPSS_CSC) += xilinx-vpss-csc.o
+obj-$(CONFIG_VIDEO_XILINX_VPSS_SCALER) += xilinx-vpss-scaler.o
 obj-$(CONFIG_VIDEO_XILINX_VTC) += xilinx-vtc.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-axis-broadcaster.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-axis-broadcaster.c
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AXI4-Stream Video Broadcaster
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ *
+ * Author: Ronak Shah <ronak.shah@xilinx.com>
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/media-device.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define MAX_VBR_SINKS			1
+#define MIN_VBR_SRCS			2
+#define MAX_VBR_SRCS			16
+
+/**
+ * struct xvbroadcaster_device - AXI4-Stream Broadcaster device structure
+ * @dev: Platform structure
+ * @subdev: The v4l2 subdev structure
+ * @pads: media pads
+ * @formats: active V4L2 media bus formats on each pad
+ * @npads: number of pads
+ */
+struct xvbroadcaster_device {
+	struct device *dev;
+	struct v4l2_subdev subdev;
+	struct media_pad *pads;
+	struct v4l2_mbus_framefmt formats;
+	u32 npads;
+};
+
+static inline struct xvbroadcaster_device *to_xvbr(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xvbroadcaster_device, subdev);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xvbr_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+xvbr_get_pad_format(struct xvbroadcaster_device *xvbr,
+		    struct v4l2_subdev_state *sd_state,
+		    unsigned int pad, u32 which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_format(&xvbr->subdev, sd_state, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &xvbr->formats;
+	default:
+		return NULL;
+	}
+}
+
+static int xvbr_get_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xvbroadcaster_device *xvbr = to_xvbr(subdev);
+
+	fmt->format = *xvbr_get_pad_format(xvbr, sd_state, fmt->pad, fmt->which);
+
+	return 0;
+}
+
+static int xvbr_set_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xvbroadcaster_device *xvbr = to_xvbr(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = xvbr_get_pad_format(xvbr, sd_state, fmt->pad, fmt->which);
+
+	*format = fmt->format;
+
+	xvip_set_format_size(format, fmt);
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xvbr_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xvbroadcaster_device *xvbr = to_xvbr(subdev);
+	struct v4l2_mbus_framefmt *format;
+	unsigned int i;
+
+	for (i = 0; i < xvbr->npads; ++i) {
+		format = v4l2_subdev_get_try_format(subdev, fh->state, i);
+		*format = xvbr->formats;
+	}
+
+	return 0;
+}
+
+static int xvbr_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_video_ops xvbr_video_ops = {
+	.s_stream = xvbr_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xvbr_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xvbr_get_format,
+	.set_fmt = xvbr_set_format,
+};
+
+static struct v4l2_subdev_ops xvbr_ops = {
+	.video = &xvbr_video_ops,
+	.pad = &xvbr_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xvbr_internal_ops = {
+	.open = xvbr_open,
+	.close = xvbr_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xvbr_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int xvbr_parse_of(struct xvbroadcaster_device *xvbr)
+{
+	struct device_node *node = xvbr->dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	for_each_child_of_node(ports, port) {
+		struct device_node *endpoint;
+
+		if (!port->name || of_node_cmp(port->name, "port"))
+			continue;
+
+		endpoint = of_get_next_child(port, NULL);
+		if (!endpoint) {
+			dev_err(xvbr->dev, "No port at\n");
+			return -EINVAL;
+		}
+
+		/* Count the number of ports. */
+		xvbr->npads++;
+	}
+
+	/* validate number of ports */
+	if ((xvbr->npads > (MAX_VBR_SINKS + MAX_VBR_SRCS)) ||
+	    (xvbr->npads < (MAX_VBR_SINKS + MIN_VBR_SRCS))) {
+		dev_err(xvbr->dev, "invalid number of ports %u\n", xvbr->npads);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int xvbr_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xvbroadcaster_device *xvbr;
+	unsigned int i;
+	int ret;
+
+	xvbr = devm_kzalloc(&pdev->dev, sizeof(*xvbr), GFP_KERNEL);
+	if (!xvbr)
+		return -ENOMEM;
+
+	xvbr->dev = &pdev->dev;
+
+	ret = xvbr_parse_of(xvbr);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Initialize V4L2 subdevice and media entity
+	 */
+	xvbr->pads = devm_kzalloc(&pdev->dev, xvbr->npads * sizeof(*xvbr->pads),
+				  GFP_KERNEL);
+	if (!xvbr->pads)
+		return -ENOMEM;
+
+	xvbr->pads[0].flags = MEDIA_PAD_FL_SINK;
+
+	for (i = 1; i < xvbr->npads; ++i)
+		xvbr->pads[i].flags = MEDIA_PAD_FL_SOURCE;
+
+	xvbr->formats.code = MEDIA_BUS_FMT_RGB888_1X24;
+	xvbr->formats.field = V4L2_FIELD_NONE;
+	xvbr->formats.colorspace = V4L2_COLORSPACE_SRGB;
+	xvbr->formats.width = XVIP_MAX_WIDTH;
+	xvbr->formats.height = XVIP_MAX_HEIGHT;
+
+	subdev = &xvbr->subdev;
+	v4l2_subdev_init(subdev, &xvbr_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xvbr_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xvbr);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	subdev->entity.ops = &xvbr_media_ops;
+
+	ret = media_entity_pads_init(&subdev->entity, xvbr->npads, xvbr->pads);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xvbr);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	dev_info(xvbr->dev, "Xilinx AXI4-Stream Broadcaster found!\n");
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+
+	return ret;
+}
+
+static int xvbr_remove(struct platform_device *pdev)
+{
+	struct xvbroadcaster_device *xvbr = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xvbr->subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+
+	return 0;
+}
+
+static const struct of_device_id xvbr_of_id_table[] = {
+	{ .compatible = "xlnx,axis-broadcaster-1.1" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xvbr_of_id_table);
+
+static struct platform_driver xvbr_driver = {
+	.driver = {
+		.name		= "xilinx-axis-broadcaster",
+		.of_match_table	= xvbr_of_id_table,
+	},
+	.probe			= xvbr_probe,
+	.remove			= xvbr_remove,
+};
+
+module_platform_driver(xvbr_driver);
+
+MODULE_AUTHOR("Ronak Shah <ronak.shah@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx AXI4-Stream Broadcaster Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-axis-subsetconv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-axis-subsetconv.c
@@ -0,0 +1,355 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Axis Subset Converter Driver
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ *
+ * Authors: Anil Kumar M <anil.mamidal@xilinx.com>
+ *          Karthikeyan T <karthikeyan.thangavel@xilinx.com>
+ *
+ * This converter driver is for matching the format of source pad
+ * and sink pad in the media pipeline. The format of a source does
+ * not match the sink pad if it is converted by a non-memory mapped
+ * hardware IP. This subset converter driver is for non-memory mapped
+ * axi stream subset converter which converts the format of the stream.
+ *
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/v4l2-subdev.h>
+#include <media/media-entity.h>
+#include <media/v4l2-subdev.h>
+#include "xilinx-vip.h"
+
+/* Number of media pads */
+#define XSUBSETCONV_MEDIA_PADS		(2)
+
+#define XSUBSETCONV_DEFAULT_WIDTH	(1920)
+#define XSUBSETCONV_DEFAULT_HEIGHT	(1080)
+
+/**
+ * struct xsubsetconv_state - SW format converter device structure
+ * @dev: Core structure for SW format converter
+ * @subdev: The v4l2 subdev structure
+ * @formats: Active V4L2 formats on each pad
+ * @lock: mutex for serializing operations
+ * @pads: media pads
+ *
+ * This structure contains the device driver related parameters
+ */
+struct xsubsetconv_state {
+	struct device *dev;
+	struct v4l2_subdev subdev;
+	struct v4l2_mbus_framefmt formats[2];
+	struct mutex lock; /* mutex lock for serializing operations */
+	struct media_pad pads[XSUBSETCONV_MEDIA_PADS];
+};
+
+static const struct of_device_id xsubsetconv_of_id_table[] = {
+	{ .compatible = "xlnx,axis-subsetconv-1.1"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xsubsetconv_of_id_table);
+
+static inline struct xsubsetconv_state *
+to_xsubsetconvstate(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xsubsetconv_state, subdev);
+}
+
+static struct v4l2_mbus_framefmt *
+xsubsetconv_get_pad_format(struct xsubsetconv_state *xsubsetconv,
+			   struct v4l2_subdev_state *state,
+			   unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xsubsetconv->subdev, state, pad);
+		break;
+
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format =  &xsubsetconv->formats[pad];
+		break;
+
+	default:
+		format = NULL;
+	}
+
+	return format;
+}
+
+/**
+ * xsubsetconv_get_format - Get the pad format
+ * @sd: pointer to v4l2 sub device structure
+ * @state: pointer to sub device pad information structure
+ * @fmt: pointer to pad level media bus format
+ *
+ * This function is used to get the pad format information.
+ *
+ * Return: -EINVAL or 0 on success
+ */
+static int xsubsetconv_get_format(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xsubsetconv_state *xsubsetconv = to_xsubsetconvstate(sd);
+	struct v4l2_mbus_framefmt *get_fmt;
+	int ret = 0;
+
+	mutex_lock(&xsubsetconv->lock);
+	get_fmt = xsubsetconv_get_pad_format(xsubsetconv, state,
+					     fmt->pad, fmt->which);
+
+	if (!get_fmt) {
+		ret = -EINVAL;
+		goto unlock_get_format;
+	}
+	fmt->format = *get_fmt;
+
+unlock_get_format:
+	mutex_unlock(&xsubsetconv->lock);
+
+	return ret;
+}
+
+/**
+ * xsubsetconv_set_format - This is used to set the pad format
+ * @sd: Pointer to V4L2 Sub device structure
+ * @state: Pointer to sub device pad information structure
+ * @fmt: Pointer to pad level media bus format
+ *
+ * This function is used to set the pad format.
+ * Since the pad format is converted in hardware which is not
+ * memory based IP, this driver will convert the source pad format
+ * to the hardware outputting sink pad format. It actually cannot
+ * convert any format.
+ *
+ * Return: -EINVAL or 0 on success
+ */
+static int xsubsetconv_set_format(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *state,
+				  struct v4l2_subdev_format *fmt)
+{
+	struct v4l2_mbus_framefmt *format;
+	struct xsubsetconv_state *xsubsetconv = to_xsubsetconvstate(sd);
+	unsigned int src_code;
+	int ret = 0;
+
+	mutex_lock(&xsubsetconv->lock);
+
+	format = xsubsetconv_get_pad_format(xsubsetconv, state,
+					    fmt->pad, fmt->which);
+	if (!format) {
+		dev_err(xsubsetconv->dev, "get pad format error\n");
+		ret = -EINVAL;
+		goto unlock_set_fmt;
+	}
+
+	/* Restore the original pad format code */
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		struct v4l2_mbus_framefmt *sink_fmt;
+
+		sink_fmt = xsubsetconv_get_pad_format(xsubsetconv, state,
+						      XVIP_PAD_SINK, fmt->which);
+		if (!sink_fmt) {
+			dev_err(xsubsetconv->dev, "get sink pad format error\n");
+			ret = -EINVAL;
+			goto unlock_set_fmt;
+		}
+		/*
+		 * TODO: Need to add a check to compare sink format and possible
+		 *		 src format supported by subset converter
+		 */
+		*format = *sink_fmt;
+		format->code = fmt->format.code;
+
+	} else {
+		struct v4l2_mbus_framefmt *src_fmt;
+
+		src_fmt = xsubsetconv_get_pad_format(xsubsetconv, state,
+						     XVIP_PAD_SOURCE, fmt->which);
+		if (!src_fmt) {
+			dev_err(xsubsetconv->dev, "get source pad format error\n");
+			ret = -EINVAL;
+			goto unlock_set_fmt;
+		}
+
+		*format = fmt->format;
+		src_code = src_fmt->code;
+		*src_fmt = *format;
+		src_fmt->code = src_code;
+	}
+
+unlock_set_fmt:
+	mutex_unlock(&xsubsetconv->lock);
+
+	return ret;
+}
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xsubsetconv_media_ops = {
+	.link_validate = v4l2_subdev_link_validate
+};
+
+static struct v4l2_subdev_pad_ops xsubsetconv_pad_ops = {
+	.get_fmt = xsubsetconv_get_format,
+	.set_fmt = xsubsetconv_set_format,
+};
+
+static struct v4l2_subdev_ops xsubsetconv_ops = {
+	.pad = &xsubsetconv_pad_ops
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int xsubsetconv_parse_of(struct xsubsetconv_state *xsubsetconv)
+{
+	struct device_node *node = xsubsetconv->dev->of_node;
+	struct device_node *ports = NULL;
+	struct device_node *port = NULL;
+	unsigned int nports = 0;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	for_each_child_of_node(ports, port) {
+		struct device_node *endpoint;
+
+		if (!port->name || of_node_cmp(port->name, "port"))
+			continue;
+
+		endpoint = of_get_next_child(port, NULL);
+		if (!endpoint) {
+			dev_err(xsubsetconv->dev, "No port at\n");
+			return -EINVAL;
+		}
+
+		dev_dbg(xsubsetconv->dev, "%s : port %d\n", __func__, nports);
+
+		/* Count the number of ports. */
+		nports++;
+	}
+
+	if (nports != XSUBSETCONV_MEDIA_PADS) {
+		dev_err(xsubsetconv->dev, "invalid number of ports %u\n", nports);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int xsubsetconv_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xsubsetconv_state *xsubsetconv;
+	int ret;
+
+	xsubsetconv = devm_kzalloc(&pdev->dev, sizeof(*xsubsetconv), GFP_KERNEL);
+	if (!xsubsetconv)
+		return -ENOMEM;
+
+	xsubsetconv->dev = &pdev->dev;
+
+	ret = xsubsetconv_parse_of(xsubsetconv);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "xsubsetconv_parse_of ret = %d\n", ret);
+		return ret;
+	}
+
+	mutex_init(&xsubsetconv->lock);
+
+	/* Initialize V4L2 subdevice and media entity */
+	xsubsetconv->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xsubsetconv->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Initialize the sink format */
+	memset(&xsubsetconv->formats[XVIP_PAD_SINK], 0,
+	       sizeof(xsubsetconv->formats[0]));
+	xsubsetconv->formats[XVIP_PAD_SINK].code = MEDIA_BUS_FMT_RGB888_1X24;
+	xsubsetconv->formats[XVIP_PAD_SINK].field = V4L2_FIELD_NONE;
+	xsubsetconv->formats[XVIP_PAD_SINK].colorspace = V4L2_COLORSPACE_SRGB;
+	xsubsetconv->formats[XVIP_PAD_SINK].width = XSUBSETCONV_DEFAULT_WIDTH;
+	xsubsetconv->formats[XVIP_PAD_SINK].height = XSUBSETCONV_DEFAULT_HEIGHT;
+
+	xsubsetconv->formats[XVIP_PAD_SOURCE] = xsubsetconv->formats[XVIP_PAD_SINK];
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xsubsetconv->subdev;
+
+	v4l2_subdev_init(subdev, &xsubsetconv_ops);
+
+	subdev->dev = &pdev->dev;
+	strscpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	subdev->entity.ops = &xsubsetconv_media_ops;
+
+	v4l2_set_subdevdata(subdev, xsubsetconv);
+
+	ret = media_entity_pads_init(&subdev->entity, XSUBSETCONV_MEDIA_PADS,
+				     xsubsetconv->pads);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "media pad init failed = %d\n", ret);
+		mutex_destroy(&xsubsetconv->lock);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, xsubsetconv);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	dev_info(&pdev->dev, "Xilinx AXI4-Stream Subset Converter found!\n");
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+	mutex_destroy(&xsubsetconv->lock);
+
+	return ret;
+}
+
+static int xsubsetconv_remove(struct platform_device *pdev)
+{
+	struct xsubsetconv_state *xsubsetconv = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xsubsetconv->subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+	mutex_destroy(&xsubsetconv->lock);
+
+	return 0;
+}
+
+static struct platform_driver xsubsetconv_driver = {
+	.driver = {
+		.name		= "xlnx,axis-subsetconv-1.1",
+		.of_match_table	= xsubsetconv_of_id_table,
+	},
+	.probe			= xsubsetconv_probe,
+	.remove			= xsubsetconv_remove,
+};
+
+module_platform_driver(xsubsetconv_driver);
+
+MODULE_AUTHOR("Anil Kumar M <anil.mamidal@xilinx.com>");
+MODULE_AUTHOR("Karthikeyan T <karthikeyan.thangavel@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx AXI4-Stream Subset Converter Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-axis-switch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-axis-switch.c
@@ -0,0 +1,630 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AXI4-Stream Video Switch
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Author: Vishal Sagar <vishal.sagar@xilinx.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/media-device.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XVSW_CTRL_REG			0x00
+#define XVSW_CTRL_REG_UPDATE_MASK	BIT(1)
+
+#define XVSW_MI_MUX_REG_BASE		0x40
+#define XVSW_MI_MUX_VAL_MASK		0xF
+#define XVSW_MI_MUX_DISABLE_MASK	BIT(31)
+
+#define MIN_VSW_SINKS			1
+#define MAX_VSW_SINKS			16
+#define MIN_VSW_SRCS			1
+#define MAX_VSW_SRCS			16
+
+/**
+ * struct xvswitch_device - Xilinx AXI4-Stream Switch device structure
+ * @dev: Platform structure
+ * @iomem: Base address of IP
+ * @subdev: The v4l2 subdev structure
+ * @pads: media pads
+ * @routing: sink pad connected to each source pad (-1 if none)
+ * @formats: active V4L2 media bus formats on sink pads
+ * @nsinks: number of sink pads (1 to 8)
+ * @nsources: number of source pads (2 to 8)
+ * @tdest_routing: Whether TDEST routing is enabled
+ * @aclk: Video clock
+ * @saxi_ctlclk: AXI-Lite control clock
+ */
+struct xvswitch_device {
+	struct device *dev;
+	void __iomem *iomem;
+	struct v4l2_subdev subdev;
+	struct media_pad *pads;
+	int routing[MAX_VSW_SRCS];
+	struct v4l2_mbus_framefmt *formats;
+	u32 nsinks;
+	u32 nsources;
+	bool tdest_routing;
+	struct clk *aclk;
+	struct clk *saxi_ctlclk;
+};
+
+static inline struct xvswitch_device *to_xvsw(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xvswitch_device, subdev);
+}
+
+static inline u32 xvswitch_read(struct xvswitch_device *xvsw, u32 addr)
+{
+	return ioread32(xvsw->iomem + addr);
+}
+
+static inline void xvswitch_write(struct xvswitch_device *xvsw, u32 addr,
+				  u32 value)
+{
+	iowrite32(value, xvsw->iomem + addr);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xvsw_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xvswitch_device *xvsw = to_xvsw(subdev);
+	unsigned int i;
+
+	/* Nothing to be done in case of TDEST routing */
+	if (xvsw->tdest_routing)
+		return 0;
+
+	if (!enable) {
+		/* In control reg routing, disable all master ports */
+		for (i = 0; i < xvsw->nsources; i++) {
+			xvswitch_write(xvsw, XVSW_MI_MUX_REG_BASE + (i * 4),
+				       XVSW_MI_MUX_DISABLE_MASK);
+		}
+		xvswitch_write(xvsw, XVSW_CTRL_REG, XVSW_CTRL_REG_UPDATE_MASK);
+		return 0;
+	}
+
+	/*
+	 * In case of control reg routing,
+	 * from routing table write the values into respective reg
+	 * and enable
+	 */
+	for (i = 0; i < MAX_VSW_SRCS; i++) {
+		u32 val;
+
+		if (xvsw->routing[i] != -1)
+			val = xvsw->routing[i];
+		else
+			val = XVSW_MI_MUX_DISABLE_MASK;
+
+		xvswitch_write(xvsw, XVSW_MI_MUX_REG_BASE + (i * 4),
+			       val);
+	}
+
+	xvswitch_write(xvsw, XVSW_CTRL_REG, XVSW_CTRL_REG_UPDATE_MASK);
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+xvsw_get_pad_format(struct xvswitch_device *xvsw,
+		    struct v4l2_subdev_state *sd_state,
+		    unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *get_fmt;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		get_fmt = v4l2_subdev_get_try_format(&xvsw->subdev, sd_state,
+						     pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		get_fmt = &xvsw->formats[pad];
+		break;
+	default:
+		get_fmt = NULL;
+		break;
+	}
+
+	return get_fmt;
+}
+
+static int xvsw_get_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xvswitch_device *xvsw = to_xvsw(subdev);
+	int pad = fmt->pad;
+	struct v4l2_mbus_framefmt *get_fmt;
+
+	/*
+	 * If control reg routing and pad is source pad then
+	 * get corresponding sink pad. if no sink pad then
+	 * clear the format and return
+	 */
+
+	if (!xvsw->tdest_routing && pad >= xvsw->nsinks) {
+		pad = xvsw->routing[pad - xvsw->nsinks];
+		if (pad < 0) {
+			memset(&fmt->format, 0, sizeof(fmt->format));
+			return 0;
+		}
+	}
+
+	get_fmt = xvsw_get_pad_format(xvsw, sd_state, pad, fmt->which);
+	if (!get_fmt)
+		return -EINVAL;
+
+	fmt->format = *get_fmt;
+
+	return 0;
+}
+
+static int xvsw_set_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xvswitch_device *xvsw = to_xvsw(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	if (!xvsw->tdest_routing && fmt->pad >= xvsw->nsinks) {
+		/*
+		 * In case of control reg routing,
+		 * get the corresponding sink pad to source pad passed.
+		 *
+		 * The source pad format is always identical to the
+		 * sink pad format and can't be modified.
+		 *
+		 * If sink pad found then get_format for that pad
+		 * else clear the fmt->format as the source pad
+		 * isn't connected and return.
+		 */
+		return xvsw_get_format(subdev, sd_state, fmt);
+	}
+
+	if (xvsw->nsinks == 1 && fmt->pad != 0) {
+		struct v4l2_mbus_framefmt *sinkformat;
+
+		/*
+		 * in tdest routing if there is only one sink then all the
+		 * source pads will have same property as sink pad, assuming
+		 * streams going to each source pad will have same
+		 * properties.
+		 */
+
+		/* get sink pad format */
+		sinkformat = xvsw_get_pad_format(xvsw, sd_state, 0, fmt->which);
+		if (!sinkformat)
+			return -EINVAL;
+
+		fmt->format = *sinkformat;
+
+		/* set sink pad format on source pad */
+		format = xvsw_get_pad_format(xvsw, sd_state, fmt->pad, fmt->which);
+		if (!format)
+			return -EINVAL;
+
+		*format = *sinkformat;
+
+		return 0;
+	}
+
+	/*
+	 * In TDEST routing mode, one can set any format on the pad as
+	 * it can't be checked which pad's data will travel to
+	 * which pad. E.g. In a system with 2 slaves and 4 masters,
+	 * S0 or S1 data can reach M0 thru M3 based on TDEST
+	 * S0 may have RBG and S1 may have YUV. M0, M1 stream RBG
+	 * and M2, M3 stream YUV based on TDEST.
+	 *
+	 * In Control reg routing mode, set format only for sink pads.
+	 */
+	format = xvsw_get_pad_format(xvsw, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	format->code = fmt->format.code;
+	format->width = clamp_t(unsigned int, fmt->format.width,
+				XVIP_MIN_WIDTH, XVIP_MAX_WIDTH);
+	format->height = clamp_t(unsigned int, fmt->format.height,
+				 XVIP_MIN_HEIGHT, XVIP_MAX_HEIGHT);
+	format->field = V4L2_FIELD_NONE;
+	format->colorspace = V4L2_COLORSPACE_SRGB;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xvsw_get_routing(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_routing *route)
+{
+	struct xvswitch_device *xvsw = to_xvsw(subdev);
+	unsigned int i;
+	u32 min;
+
+	/* In case of tdest routing, we can't get routing */
+	if (xvsw->tdest_routing)
+		return -EINVAL;
+
+	mutex_lock(&subdev->entity.graph_obj.mdev->graph_mutex);
+
+	if (xvsw->nsources < route->num_routes)
+		min = xvsw->nsources;
+	else
+		min = route->num_routes;
+
+	for (i = 0; i < min; ++i) {
+		route->routes[i].sink = xvsw->routing[i];
+		route->routes[i].source = i;
+	}
+
+	route->num_routes = xvsw->nsources;
+
+	mutex_unlock(&subdev->entity.graph_obj.mdev->graph_mutex);
+
+	return 0;
+}
+
+static int xvsw_set_routing(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_routing *route)
+{
+	struct xvswitch_device *xvsw = to_xvsw(subdev);
+	unsigned int i;
+	int ret = 0;
+
+	/* In case of tdest routing, we can't set routing */
+	if (xvsw->tdest_routing)
+		return -EINVAL;
+
+	mutex_lock(&subdev->entity.graph_obj.mdev->graph_mutex);
+
+	if (subdev->entity.stream_count) {
+		ret = -EBUSY;
+		goto done;
+	}
+
+	for (i = 0; i < xvsw->nsources; ++i)
+		xvsw->routing[i] = -1;
+
+	for (i = 0; i < route->num_routes; ++i)
+		xvsw->routing[route->routes[i].source - xvsw->nsinks] =
+			route->routes[i].sink;
+
+done:
+	mutex_unlock(&subdev->entity.graph_obj.mdev->graph_mutex);
+	return ret;
+}
+
+static int xvsw_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static int xvsw_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_video_ops xvsw_video_ops = {
+	.s_stream = xvsw_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xvsw_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xvsw_get_format,
+	.set_fmt = xvsw_set_format,
+	.get_routing = xvsw_get_routing,
+	.set_routing = xvsw_set_routing,
+};
+
+static struct v4l2_subdev_ops xvsw_ops = {
+	.video = &xvsw_video_ops,
+	.pad = &xvsw_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xvsw_internal_ops = {
+	.open = xvsw_open,
+	.close = xvsw_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static bool xvsw_has_route(struct media_entity *entity, unsigned int pad0,
+			   unsigned int pad1)
+{
+	struct xvswitch_device *xvsw =
+		container_of(entity, struct xvswitch_device, subdev.entity);
+	unsigned int sink0, sink1;
+
+	/* Two sinks are never connected together. */
+	if (pad0 < xvsw->nsinks && pad1 < xvsw->nsinks)
+		return false;
+
+	/* In TDEST routing, assume all sinks and sources are connected */
+	if (xvsw->tdest_routing)
+		return true;
+
+	sink0 = pad0 < xvsw->nsinks ? pad0 : xvsw->routing[pad0 - xvsw->nsinks];
+	sink1 = pad1 < xvsw->nsinks ? pad1 : xvsw->routing[pad1 - xvsw->nsinks];
+
+	return sink0 == sink1;
+}
+
+static const struct media_entity_operations xvsw_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+	.has_route = xvsw_has_route,
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int xvsw_parse_of(struct xvswitch_device *xvsw)
+{
+	struct device_node *node = xvsw->dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	unsigned int nports = 0;
+	u32 routing_mode = 0;
+	int ret;
+
+	ret = of_property_read_u32(node, "xlnx,num-si-slots", &xvsw->nsinks);
+	if (ret < 0 || xvsw->nsinks < MIN_VSW_SINKS ||
+	    xvsw->nsinks > MAX_VSW_SINKS) {
+		dev_err(xvsw->dev, "missing or invalid xlnx,num-si-slots property\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-mi-slots", &xvsw->nsources);
+	if (ret < 0 || xvsw->nsources < MIN_VSW_SRCS ||
+	    xvsw->nsources > MAX_VSW_SRCS) {
+		dev_err(xvsw->dev, "missing or invalid xlnx,num-mi-slots property\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,routing-mode", &routing_mode);
+	if (ret < 0 || routing_mode > 1) {
+		dev_err(xvsw->dev, "missing or invalid xlnx,routing property\n");
+		return ret;
+	}
+
+	if (!routing_mode)
+		xvsw->tdest_routing = true;
+
+	xvsw->aclk = devm_clk_get(xvsw->dev, "aclk");
+	if (IS_ERR(xvsw->aclk)) {
+		ret = PTR_ERR(xvsw->aclk);
+		dev_err(xvsw->dev, "failed to get ap_clk (%d)\n", ret);
+		return ret;
+	}
+
+	if (!xvsw->tdest_routing) {
+		xvsw->saxi_ctlclk = devm_clk_get(xvsw->dev,
+						 "s_axi_ctl_clk");
+		if (IS_ERR(xvsw->saxi_ctlclk)) {
+			ret = PTR_ERR(xvsw->saxi_ctlclk);
+			dev_err(xvsw->dev,
+				"failed to get s_axi_ctl_clk (%d)\n",
+				ret);
+			return ret;
+		}
+	}
+
+	if (xvsw->tdest_routing && xvsw->nsinks > 1) {
+		dev_err(xvsw->dev, "sinks = %d. Driver Limitation max 1 sink in TDEST routing mode\n",
+			xvsw->nsinks);
+		return -EINVAL;
+	}
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	for_each_child_of_node(ports, port) {
+		struct device_node *endpoint;
+
+		if (!port->name || of_node_cmp(port->name, "port"))
+			continue;
+
+		endpoint = of_get_next_child(port, NULL);
+		if (!endpoint) {
+			dev_err(xvsw->dev, "No port at\n");
+			return -EINVAL;
+		}
+
+		/* Count the number of ports. */
+		nports++;
+	}
+
+	/* validate number of ports */
+	if (nports != (xvsw->nsinks + xvsw->nsources)) {
+		dev_err(xvsw->dev, "invalid number of ports %u\n", nports);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int xvsw_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xvswitch_device *xvsw;
+	struct resource *res;
+	unsigned int npads;
+	unsigned int i, padcount;
+	int ret;
+
+	xvsw = devm_kzalloc(&pdev->dev, sizeof(*xvsw), GFP_KERNEL);
+	if (!xvsw)
+		return -ENOMEM;
+
+	xvsw->dev = &pdev->dev;
+
+	ret = xvsw_parse_of(xvsw);
+	if (ret < 0)
+		return ret;
+
+	/* ioremap only if control reg based routing */
+	if (!xvsw->tdest_routing) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		xvsw->iomem = devm_ioremap_resource(xvsw->dev, res);
+		if (IS_ERR(xvsw->iomem))
+			return PTR_ERR(xvsw->iomem);
+	}
+
+	/*
+	 * Initialize V4L2 subdevice and media entity. Pad numbers depend on the
+	 * number of pads.
+	 */
+	npads = xvsw->nsinks + xvsw->nsources;
+	xvsw->pads = devm_kzalloc(&pdev->dev, npads * sizeof(*xvsw->pads),
+				  GFP_KERNEL);
+	if (!xvsw->pads)
+		return -ENOMEM;
+
+	for (i = 0; i < xvsw->nsinks; ++i)
+		xvsw->pads[i].flags = MEDIA_PAD_FL_SINK;
+
+	for (; i < npads; ++i)
+		xvsw->pads[i].flags = MEDIA_PAD_FL_SOURCE;
+
+	padcount = xvsw->tdest_routing ? npads : xvsw->nsinks;
+
+	/*
+	 * In case of tdest routing, allocate format per pad.
+	 * source pad format has to match one of the sink pads in tdest routing.
+	 *
+	 * Otherwise only allocate for sinks as sources will
+	 * get the same pad format and corresponding sink.
+	 * set format on src pad will return corresponding sinks data.
+	 */
+	xvsw->formats = devm_kzalloc(&pdev->dev,
+				     padcount * sizeof(*xvsw->formats),
+				     GFP_KERNEL);
+	if (!xvsw->formats) {
+		dev_err(xvsw->dev, "No memory to allocate formats!\n");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < padcount; i++) {
+		xvsw->formats[i].code = MEDIA_BUS_FMT_RGB888_1X24;
+		xvsw->formats[i].field = V4L2_FIELD_NONE;
+		xvsw->formats[i].colorspace = V4L2_COLORSPACE_SRGB;
+		xvsw->formats[i].width = XVIP_MAX_WIDTH;
+		xvsw->formats[i].height = XVIP_MAX_HEIGHT;
+	}
+
+	/*
+	 * Initialize the routing table if none are connected.
+	 * Routing table is valid only incase routing is not TDEST based.
+	 */
+	for (i = 0; i < MAX_VSW_SRCS; ++i)
+		xvsw->routing[i] = -1;
+
+	ret = clk_prepare_enable(xvsw->aclk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable aclk (%d)\n",
+			ret);
+		return ret;
+	}
+
+	if (!xvsw->tdest_routing) {
+		ret = clk_prepare_enable(xvsw->saxi_ctlclk);
+		if (ret) {
+			dev_err(&pdev->dev,
+				"failed to enable s_axi_ctl_clk (%d)\n",
+				ret);
+			clk_disable_unprepare(xvsw->aclk);
+			return ret;
+		}
+	}
+
+	subdev = &xvsw->subdev;
+	v4l2_subdev_init(subdev, &xvsw_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xvsw_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xvsw);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	subdev->entity.ops = &xvsw_media_ops;
+
+	ret = media_entity_pads_init(&subdev->entity, npads, xvsw->pads);
+	if (ret < 0)
+		goto clk_error;
+
+	platform_set_drvdata(pdev, xvsw);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	dev_info(xvsw->dev, "Xilinx AXI4-Stream Switch found!\n");
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+clk_error:
+	if (!xvsw->tdest_routing)
+		clk_disable_unprepare(xvsw->saxi_ctlclk);
+	clk_disable_unprepare(xvsw->aclk);
+	return ret;
+}
+
+static int xvsw_remove(struct platform_device *pdev)
+{
+	struct xvswitch_device *xvsw = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xvsw->subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+	if (!xvsw->tdest_routing)
+		clk_disable_unprepare(xvsw->saxi_ctlclk);
+	clk_disable_unprepare(xvsw->aclk);
+	return 0;
+}
+
+static const struct of_device_id xvsw_of_id_table[] = {
+	{ .compatible = "xlnx,axis-switch-1.1" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xvsw_of_id_table);
+
+static struct platform_driver xvsw_driver = {
+	.driver = {
+		.name		= "xilinx-axis-switch",
+		.of_match_table	= xvsw_of_id_table,
+	},
+	.probe			= xvsw_probe,
+	.remove			= xvsw_remove,
+};
+
+module_platform_driver(xvsw_driver);
+
+MODULE_AUTHOR("Vishal Sagar <vishal.sagar@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx AXI4-Stream Switch Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-cfa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-cfa.c
@@ -0,0 +1,410 @@
+/*
+ * Xilinx Color Filter Array
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XCFA_BAYER_PHASE	0x100
+#define XCFA_BAYER_PHASE_RGGB	0
+#define XCFA_BAYER_PHASE_GRBG	1
+#define XCFA_BAYER_PHASE_GBRG	2
+#define XCFA_BAYER_PHASE_BGGR	3
+
+/**
+ * struct xcfa_device - Xilinx CFA device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @formats: V4L2 media bus formats
+ * @default_formats: default V4L2 media bus formats
+ * @vip_formats: Xilinx Video IP formats
+ */
+struct xcfa_device {
+	struct xvip_device xvip;
+
+	struct media_pad pads[2];
+
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_formats[2];
+};
+
+static inline struct xcfa_device *to_cfa(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xcfa_device, xvip.subdev);
+}
+
+/*
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xcfa_get_bayer_phase(const unsigned int code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+		return XCFA_BAYER_PHASE_RGGB;
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+		return XCFA_BAYER_PHASE_GRBG;
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+		return XCFA_BAYER_PHASE_GBRG;
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+		return XCFA_BAYER_PHASE_BGGR;
+	}
+
+	return -EINVAL;
+}
+
+static int xcfa_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xcfa_device *xcfa = to_cfa(subdev);
+	const unsigned int code = xcfa->formats[XVIP_PAD_SINK].code;
+	u32 bayer_phase;
+
+	if (!enable) {
+		xvip_stop(&xcfa->xvip);
+		return 0;
+	}
+
+	/* This always returns the valid bayer phase value */
+	bayer_phase = xcfa_get_bayer_phase(code);
+
+	xvip_write(&xcfa->xvip, XCFA_BAYER_PHASE, bayer_phase);
+
+	xvip_set_frame_size(&xcfa->xvip, &xcfa->formats[XVIP_PAD_SINK]);
+
+	xvip_start(&xcfa->xvip);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+__xcfa_get_pad_format(struct xcfa_device *xcfa,
+		      struct v4l2_subdev_state *sd_state,
+		      unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xcfa->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xcfa->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xcfa_get_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xcfa_device *xcfa = to_cfa(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xcfa_get_pad_format(xcfa, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xcfa_set_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xcfa_device *xcfa = to_cfa(subdev);
+	struct v4l2_mbus_framefmt *format;
+	int bayer_phase;
+
+	format = __xcfa_get_pad_format(xcfa, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		fmt->format = *format;
+		return 0;
+	}
+
+	bayer_phase = xcfa_get_bayer_phase(fmt->format.code);
+	if (bayer_phase >= 0) {
+		xcfa->vip_formats[XVIP_PAD_SINK] =
+			xvip_get_format_by_code(fmt->format.code);
+		format->code = fmt->format.code;
+	}
+
+	xvip_set_format_size(format, fmt);
+
+	fmt->format = *format;
+
+	/* Propagate the format to the source pad */
+	format = __xcfa_get_pad_format(xcfa, sd_state, XVIP_PAD_SOURCE,
+				       fmt->which);
+
+	xvip_set_format_size(format, fmt);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Operations
+ */
+
+static int xcfa_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xcfa_device *xcfa = to_cfa(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xcfa->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xcfa->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int xcfa_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_video_ops xcfa_video_ops = {
+	.s_stream = xcfa_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xcfa_pad_ops = {
+	.enum_mbus_code		= xvip_enum_mbus_code,
+	.enum_frame_size	= xvip_enum_frame_size,
+	.get_fmt		= xcfa_get_format,
+	.set_fmt		= xcfa_set_format,
+};
+
+static struct v4l2_subdev_ops xcfa_ops = {
+	.video  = &xcfa_video_ops,
+	.pad    = &xcfa_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xcfa_internal_ops = {
+	.open	= xcfa_open,
+	.close	= xcfa_close,
+};
+
+/*
+ * Media Operations
+ */
+
+static const struct media_entity_operations xcfa_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/*
+ * Power Management
+ */
+
+static int __maybe_unused xcfa_pm_suspend(struct device *dev)
+{
+	struct xcfa_device *xcfa = dev_get_drvdata(dev);
+
+	xvip_suspend(&xcfa->xvip);
+
+	return 0;
+}
+
+static int __maybe_unused xcfa_pm_resume(struct device *dev)
+{
+	struct xcfa_device *xcfa = dev_get_drvdata(dev);
+
+	xvip_resume(&xcfa->xvip);
+
+	return 0;
+}
+
+/*
+ * Platform Device Driver
+ */
+
+static int xcfa_parse_of(struct xcfa_device *xcfa)
+{
+	struct device *dev = xcfa->xvip.dev;
+	struct device_node *node = xcfa->xvip.dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id;
+	int ret;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (ports == NULL)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			const struct xvip_video_format *vip_format;
+
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "invalid format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			ret = of_property_read_u32(port, "reg", &port_id);
+			if (ret < 0) {
+				dev_err(dev, "no reg in DT");
+				return ret;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "invalid reg in DT");
+				return -EINVAL;
+			}
+
+			xcfa->vip_formats[port_id] = vip_format;
+		}
+	}
+
+	return 0;
+}
+
+static int xcfa_probe(struct platform_device *pdev)
+{
+	struct xcfa_device *xcfa;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *default_format;
+	int ret;
+
+	xcfa = devm_kzalloc(&pdev->dev, sizeof(*xcfa), GFP_KERNEL);
+	if (!xcfa)
+		return -ENOMEM;
+
+	xcfa->xvip.dev = &pdev->dev;
+
+	ret = xcfa_parse_of(xcfa);
+	if (ret < 0)
+		return ret;
+
+	ret = xvip_init_resources(&xcfa->xvip);
+	if (ret < 0)
+		return ret;
+
+	/* Reset and initialize the core */
+	xvip_reset(&xcfa->xvip);
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xcfa->xvip.subdev;
+	v4l2_subdev_init(subdev, &xcfa_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xcfa_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xcfa);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Initialize default and active formats */
+	default_format = &xcfa->default_formats[XVIP_PAD_SINK];
+	default_format->code = xcfa->vip_formats[XVIP_PAD_SINK]->code;
+	default_format->field = V4L2_FIELD_NONE;
+	default_format->colorspace = V4L2_COLORSPACE_SRGB;
+	xvip_get_frame_size(&xcfa->xvip, default_format);
+
+	xcfa->formats[XVIP_PAD_SINK] = *default_format;
+
+	default_format = &xcfa->default_formats[XVIP_PAD_SOURCE];
+	*default_format = xcfa->default_formats[XVIP_PAD_SINK];
+	default_format->code = xcfa->vip_formats[XVIP_PAD_SOURCE]->code;
+
+	xcfa->formats[XVIP_PAD_SOURCE] = *default_format;
+
+	xcfa->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xcfa->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xcfa_media_ops;
+	ret = media_entity_pads_init(&subdev->entity, 2, xcfa->pads);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xcfa);
+
+	xvip_print_version(&xcfa->xvip);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xcfa->xvip);
+	return ret;
+}
+
+static int xcfa_remove(struct platform_device *pdev)
+{
+	struct xcfa_device *xcfa = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xcfa->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+
+	xvip_cleanup_resources(&xcfa->xvip);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(xcfa_pm_ops, xcfa_pm_suspend, xcfa_pm_resume);
+
+static const struct of_device_id xcfa_of_id_table[] = {
+	{ .compatible = "xlnx,v-cfa-7.0" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xcfa_of_id_table);
+
+static struct platform_driver xcfa_driver = {
+	.driver			= {
+		.name		= "xilinx-cfa",
+		.pm		= &xcfa_pm_ops,
+		.of_match_table	= xcfa_of_id_table,
+	},
+	.probe			= xcfa_probe,
+	.remove			= xcfa_remove,
+};
+
+module_platform_driver(xcfa_driver);
+
+MODULE_DESCRIPTION("Xilinx Color Filter Array Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-cresample.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-cresample.c
@@ -0,0 +1,461 @@
+/*
+ * Xilinx Chroma Resampler
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/xilinx-v4l2-controls.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XCRESAMPLE_ENCODING			0x100
+#define XCRESAMPLE_ENCODING_FIELD		(1 << 7)
+#define XCRESAMPLE_ENCODING_CHROMA		(1 << 8)
+
+/**
+ * struct xcresample_device - Xilinx CRESAMPLE device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @formats: V4L2 media bus formats at the sink and source pads
+ * @default_formats: default V4L2 media bus formats
+ * @vip_formats: Xilinx Video IP formats
+ * @ctrl_handler: control handler
+ */
+struct xcresample_device {
+	struct xvip_device xvip;
+
+	struct media_pad pads[2];
+
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_formats[2];
+
+	struct v4l2_ctrl_handler ctrl_handler;
+};
+
+static inline struct xcresample_device *to_cresample(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xcresample_device, xvip.subdev);
+}
+
+/*
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xcresample_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xcresample_device *xcresample = to_cresample(subdev);
+
+	if (!enable) {
+		xvip_stop(&xcresample->xvip);
+		return 0;
+	}
+
+	xvip_set_frame_size(&xcresample->xvip,
+			    &xcresample->formats[XVIP_PAD_SINK]);
+
+	xvip_start(&xcresample->xvip);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+__xcresample_get_pad_format(struct xcresample_device *xcresample,
+			    struct v4l2_subdev_state *sd_state,
+			    unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xcresample->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xcresample->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xcresample_get_format(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct xcresample_device *xcresample = to_cresample(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xcresample_get_pad_format(xcresample, sd_state, fmt->pad,
+					     fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xcresample_set_format(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct xcresample_device *xcresample = to_cresample(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xcresample_get_pad_format(xcresample, sd_state, fmt->pad,
+					     fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		fmt->format = *format;
+		return 0;
+	}
+
+	xvip_set_format_size(format, fmt);
+
+	fmt->format = *format;
+
+	/* Propagate the format to the source pad. */
+	format = __xcresample_get_pad_format(xcresample, sd_state,
+					     XVIP_PAD_SOURCE, fmt->which);
+
+	xvip_set_format_size(format, fmt);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Operations
+ */
+
+static int xcresample_open(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_fh *fh)
+{
+	struct xcresample_device *xcresample = to_cresample(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xcresample->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xcresample->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int xcresample_close(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static int xcresample_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct xcresample_device *xcresample =
+		container_of(ctrl->handler, struct xcresample_device,
+			     ctrl_handler);
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_CRESAMPLE_FIELD_PARITY:
+		xvip_clr_or_set(&xcresample->xvip, XCRESAMPLE_ENCODING,
+				XCRESAMPLE_ENCODING_FIELD, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_CRESAMPLE_CHROMA_PARITY:
+		xvip_clr_or_set(&xcresample->xvip, XCRESAMPLE_ENCODING,
+				XCRESAMPLE_ENCODING_CHROMA, ctrl->val);
+		return 0;
+	}
+
+	return -EINVAL;
+
+}
+
+static const struct v4l2_ctrl_ops xcresample_ctrl_ops = {
+	.s_ctrl	= xcresample_s_ctrl,
+};
+
+static struct v4l2_subdev_video_ops xcresample_video_ops = {
+	.s_stream = xcresample_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xcresample_pad_ops = {
+	.enum_mbus_code		= xvip_enum_mbus_code,
+	.enum_frame_size	= xvip_enum_frame_size,
+	.get_fmt		= xcresample_get_format,
+	.set_fmt		= xcresample_set_format,
+};
+
+static struct v4l2_subdev_ops xcresample_ops = {
+	.video  = &xcresample_video_ops,
+	.pad    = &xcresample_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xcresample_internal_ops = {
+	.open	= xcresample_open,
+	.close	= xcresample_close,
+};
+
+/*
+ * Control Configs
+ */
+
+static const char *const xcresample_parity_string[] = {
+	"Even",
+	"Odd",
+};
+
+static struct v4l2_ctrl_config xcresample_field = {
+	.ops	= &xcresample_ctrl_ops,
+	.id	= V4L2_CID_XILINX_CRESAMPLE_FIELD_PARITY,
+	.name	= "Chroma Resampler: Encoding Field Parity",
+	.type	= V4L2_CTRL_TYPE_MENU,
+	.min	= 0,
+	.max	= 1,
+	.qmenu	= xcresample_parity_string,
+};
+
+static struct v4l2_ctrl_config xcresample_chroma = {
+	.ops	= &xcresample_ctrl_ops,
+	.id	= V4L2_CID_XILINX_CRESAMPLE_CHROMA_PARITY,
+	.name	= "Chroma Resampler: Encoding Chroma Parity",
+	.type	= V4L2_CTRL_TYPE_MENU,
+	.min	= 0,
+	.max	= 1,
+	.qmenu	= xcresample_parity_string,
+};
+
+/*
+ * Media Operations
+ */
+
+static const struct media_entity_operations xcresample_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/*
+ * Power Management
+ */
+
+static int __maybe_unused xcresample_pm_suspend(struct device *dev)
+{
+	struct xcresample_device *xcresample = dev_get_drvdata(dev);
+
+	xvip_suspend(&xcresample->xvip);
+
+	return 0;
+}
+
+static int __maybe_unused xcresample_pm_resume(struct device *dev)
+{
+	struct xcresample_device *xcresample = dev_get_drvdata(dev);
+
+	xvip_resume(&xcresample->xvip);
+
+	return 0;
+}
+
+/*
+ * Platform Device Driver
+ */
+
+static int xcresample_parse_of(struct xcresample_device *xcresample)
+{
+	struct device *dev = xcresample->xvip.dev;
+	struct device_node *node = xcresample->xvip.dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id;
+	int ret;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (ports == NULL)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			const struct xvip_video_format *vip_format;
+
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "invalid format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			ret = of_property_read_u32(port, "reg", &port_id);
+			if (ret < 0) {
+				dev_err(dev, "no reg in DT");
+				return ret;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "invalid reg in DT");
+				return -EINVAL;
+			}
+
+			xcresample->vip_formats[port_id] = vip_format;
+		}
+	}
+
+	return 0;
+}
+
+static int xcresample_probe(struct platform_device *pdev)
+{
+	struct xcresample_device *xcresample;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *default_format;
+	int ret;
+
+	xcresample = devm_kzalloc(&pdev->dev, sizeof(*xcresample), GFP_KERNEL);
+	if (!xcresample)
+		return -ENOMEM;
+
+	xcresample->xvip.dev = &pdev->dev;
+
+	ret = xcresample_parse_of(xcresample);
+	if (ret < 0)
+		return ret;
+
+	ret = xvip_init_resources(&xcresample->xvip);
+	if (ret < 0)
+		return ret;
+
+	/* Reset and initialize the core */
+	xvip_reset(&xcresample->xvip);
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xcresample->xvip.subdev;
+	v4l2_subdev_init(subdev, &xcresample_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xcresample_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xcresample);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Initialize default and active formats */
+	default_format = &xcresample->default_formats[XVIP_PAD_SINK];
+	default_format->code = xcresample->vip_formats[XVIP_PAD_SINK]->code;
+	default_format->field = V4L2_FIELD_NONE;
+	default_format->colorspace = V4L2_COLORSPACE_SRGB;
+	xvip_get_frame_size(&xcresample->xvip, default_format);
+
+	xcresample->formats[XVIP_PAD_SINK] = *default_format;
+
+	default_format = &xcresample->default_formats[XVIP_PAD_SOURCE];
+	*default_format = xcresample->default_formats[XVIP_PAD_SINK];
+	default_format->code = xcresample->vip_formats[XVIP_PAD_SOURCE]->code;
+
+	xcresample->formats[XVIP_PAD_SOURCE] = *default_format;
+
+	xcresample->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xcresample->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xcresample_media_ops;
+	ret = media_entity_pads_init(&subdev->entity, 2, xcresample->pads);
+	if (ret < 0)
+		goto error;
+
+	v4l2_ctrl_handler_init(&xcresample->ctrl_handler, 2);
+	xcresample_field.def =
+		(xvip_read(&xcresample->xvip, XCRESAMPLE_ENCODING) &
+		 XCRESAMPLE_ENCODING_FIELD) ? 1 : 0;
+	v4l2_ctrl_new_custom(&xcresample->ctrl_handler, &xcresample_field,
+			     NULL);
+	xcresample_chroma.def =
+		(xvip_read(&xcresample->xvip, XCRESAMPLE_ENCODING) &
+		 XCRESAMPLE_ENCODING_CHROMA) ? 1 : 0;
+	v4l2_ctrl_new_custom(&xcresample->ctrl_handler, &xcresample_chroma,
+			     NULL);
+	if (xcresample->ctrl_handler.error) {
+		dev_err(&pdev->dev, "failed to add controls\n");
+		ret = xcresample->ctrl_handler.error;
+		goto error;
+	}
+	subdev->ctrl_handler = &xcresample->ctrl_handler;
+
+	platform_set_drvdata(pdev, xcresample);
+
+	xvip_print_version(&xcresample->xvip);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	v4l2_ctrl_handler_free(&xcresample->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xcresample->xvip);
+	return ret;
+}
+
+static int xcresample_remove(struct platform_device *pdev)
+{
+	struct xcresample_device *xcresample = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xcresample->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&xcresample->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+
+	xvip_cleanup_resources(&xcresample->xvip);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(xcresample_pm_ops, xcresample_pm_suspend,
+			 xcresample_pm_resume);
+
+static const struct of_device_id xcresample_of_id_table[] = {
+	{ .compatible = "xlnx,v-cresample-4.0" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xcresample_of_id_table);
+
+static struct platform_driver xcresample_driver = {
+	.driver			= {
+		.name		= "xilinx-cresample",
+		.pm		= &xcresample_pm_ops,
+		.of_match_table	= xcresample_of_id_table,
+	},
+	.probe			= xcresample_probe,
+	.remove			= xcresample_remove,
+};
+
+module_platform_driver(xcresample_driver);
+
+MODULE_DESCRIPTION("Xilinx Chroma Resampler Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-csi2rxss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-csi2rxss.c
@@ -48,6 +48,7 @@
 
 #define XCSI_ISR_FR		BIT(31)
 #define XCSI_ISR_VCXFE		BIT(30)
+#define XCSI_ISR_YUV420		BIT(28)
 #define XCSI_ISR_WCC		BIT(22)
 #define XCSI_ISR_ILC		BIT(21)
 #define XCSI_ISR_SPFIFOF	BIT(20)
@@ -69,7 +70,7 @@
 #define XCSI_ISR_VC0FSYNCERR	BIT(1)
 #define XCSI_ISR_VC0FLVLERR	BIT(0)
 
-#define XCSI_ISR_ALLINTR_MASK	(0xc07e3fff)
+#define XCSI_ISR_ALLINTR_MASK	(0xd07e3fff)
 
 /*
  * Removed VCXFE mask as it doesn't exist in IER
@@ -116,6 +117,7 @@
 #define XCSI_DEFAULT_HEIGHT	1080
 
 /* MIPI CSI-2 Data Types from spec */
+#define XCSI_DT_YUV4208B	0x18
 #define XCSI_DT_YUV4228B	0x1e
 #define XCSI_DT_YUV42210B	0x1f
 #define XCSI_DT_RGB444		0x20
@@ -154,6 +156,7 @@
 static const struct xcsi2rxss_event xcsi2rxss_events[] = {
 	{ XCSI_ISR_FR, "Frame Received" },
 	{ XCSI_ISR_VCXFE, "VCX Frame Errors" },
+	{ XCSI_ISR_YUV420, "YUV 420 Word Count Errors" },
 	{ XCSI_ISR_WCC, "Word Count Errors" },
 	{ XCSI_ISR_ILC, "Invalid Lane Count Error" },
 	{ XCSI_ISR_SPFIFOF, "Short Packet FIFO OverFlow Error" },
@@ -183,6 +186,7 @@
  * and media bus formats
  */
 static const u32 xcsi2dt_mbus_lut[][2] = {
+	{ XCSI_DT_YUV4208B, MEDIA_BUS_FMT_VYYUYY8_1X24 },
 	{ XCSI_DT_YUV4228B, MEDIA_BUS_FMT_UYVY8_1X16 },
 	{ XCSI_DT_YUV42210B, MEDIA_BUS_FMT_UYVY10_1X20 },
 	{ XCSI_DT_RGB444, 0 },
@@ -489,12 +493,15 @@
 static struct v4l2_subdev *xcsi2rxss_get_remote_subdev(struct media_pad *local)
 {
 	struct media_pad *remote;
+	struct v4l2_subdev *sd;
 
 	remote = media_entity_remote_pad(local);
 	if (!remote || !is_media_entity_v4l2_subdev(remote->entity))
-		return NULL;
+		sd = NULL;
+	else
+		sd = media_entity_to_v4l2_subdev(remote->entity);
 
-	return media_entity_to_v4l2_subdev(remote->entity);
+	return sd;
 }
 
 static int xcsi2rxss_start_stream(struct xcsi2rxss_state *state)
@@ -520,7 +527,14 @@
 	state->rsubdev =
 		xcsi2rxss_get_remote_subdev(&state->pads[XVIP_PAD_SINK]);
 
+	if (!state->rsubdev) {
+		ret = -ENODEV;
+		goto exit_start_stream;
+	}
+
 	ret = v4l2_subdev_call(state->rsubdev, video, s_stream, 1);
+
+exit_start_stream:
 	if (ret) {
 		/* disable interrupts */
 		xcsi2rxss_clr(state, XCSI_IER_OFFSET, XCSI_IER_INTR_MASK);
@@ -595,8 +609,11 @@
 	 * Stream line buffer full
 	 * This means there is a backpressure from downstream IP
 	 */
-	if (status & XCSI_ISR_SLBF) {
-		dev_alert_ratelimited(dev, "Stream Line Buffer Full!\n");
+	if (status & (XCSI_ISR_SLBF | XCSI_ISR_YUV420)) {
+		if (status & XCSI_ISR_SLBF)
+			dev_alert_ratelimited(dev, "Stream Line Buffer Full!\n");
+		if (status & XCSI_ISR_YUV420)
+			dev_alert_ratelimited(dev, "YUV 420 Word count error!\n");
 
 		/* disable interrupts */
 		xcsi2rxss_clr(state, XCSI_IER_OFFSET, XCSI_IER_INTR_MASK);
@@ -684,21 +701,28 @@
 			   struct v4l2_subdev_state *sd_state,
 			   unsigned int pad, u32 which)
 {
+	struct v4l2_mbus_framefmt *get_fmt;
+
 	switch (which) {
 	case V4L2_SUBDEV_FORMAT_TRY:
-		return v4l2_subdev_get_try_format(&xcsi2rxss->subdev,
-						  sd_state, pad);
+		get_fmt = v4l2_subdev_get_try_format(&xcsi2rxss->subdev,
+						     sd_state, pad);
+		break;
 	case V4L2_SUBDEV_FORMAT_ACTIVE:
-		return &xcsi2rxss->format;
+		get_fmt = &xcsi2rxss->format;
+		break;
 	default:
-		return NULL;
+		get_fmt = NULL;
+		break;
 	}
+
+	return get_fmt;
 }
 
 /**
  * xcsi2rxss_init_cfg - Initialise the pad format config to default
  * @sd: Pointer to V4L2 Sub device structure
- * @sd_state: Pointer to sub device state structure
+ * @cfg: Pointer to sub device pad information structure
  *
  * This function is used to initialize the pad format with the default
  * values.
@@ -725,7 +749,7 @@
 /**
  * xcsi2rxss_get_format - Get the pad format
  * @sd: Pointer to V4L2 Sub device structure
- * @sd_state: Pointer to sub device state structure
+ * @cfg: Pointer to sub device pad information structure
  * @fmt: Pointer to pad level media bus format
  *
  * This function is used to get the pad format information.
@@ -737,20 +761,30 @@
 				struct v4l2_subdev_format *fmt)
 {
 	struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
+	struct v4l2_mbus_framefmt *get_fmt;
+	int ret = 0;
 
 	mutex_lock(&xcsi2rxss->lock);
-	fmt->format = *__xcsi2rxss_get_pad_format(xcsi2rxss, sd_state,
-						  fmt->pad,
-						  fmt->which);
+
+	get_fmt = __xcsi2rxss_get_pad_format(xcsi2rxss, sd_state, fmt->pad,
+					     fmt->which);
+	if (!get_fmt) {
+		ret = -EINVAL;
+		goto unlock_get_format;
+	}
+
+	fmt->format = *get_fmt;
+
+unlock_get_format:
 	mutex_unlock(&xcsi2rxss->lock);
 
-	return 0;
+	return ret;
 }
 
 /**
  * xcsi2rxss_set_format - This is used to set the pad format
  * @sd: Pointer to V4L2 Sub device structure
- * @sd_state: Pointer to sub device state structure
+ * @cfg: Pointer to sub device pad information structure
  * @fmt: Pointer to pad level media bus format
  *
  * This function is used to set the pad format. Since the pad format is fixed
@@ -767,6 +801,7 @@
 	struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
 	struct v4l2_mbus_framefmt *__format;
 	u32 dt;
+	int ret = 0;
 
 	mutex_lock(&xcsi2rxss->lock);
 
@@ -777,12 +812,15 @@
 	 */
 	__format = __xcsi2rxss_get_pad_format(xcsi2rxss, sd_state,
 					      fmt->pad, fmt->which);
+	if (!__format) {
+		ret = -EINVAL;
+		goto unlock_set_format;
+	}
 
 	/* only sink pad format can be updated */
 	if (fmt->pad == XVIP_PAD_SOURCE) {
 		fmt->format = *__format;
-		mutex_unlock(&xcsi2rxss->lock);
-		return 0;
+		goto unlock_set_format;
 	}
 
 	/*
@@ -799,9 +837,11 @@
 	}
 
 	*__format = fmt->format;
+
+unlock_set_format:
 	mutex_unlock(&xcsi2rxss->lock);
 
-	return 0;
+	return ret;
 }
 
 /*
@@ -895,6 +935,7 @@
 	}
 
 	switch (xcsi2rxss->datatype) {
+	case XCSI_DT_YUV4208B:
 	case XCSI_DT_YUV4228B:
 	case XCSI_DT_RGB444:
 	case XCSI_DT_RGB555:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-demosaic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-demosaic.c
@@ -0,0 +1,436 @@
+/*
+ * Xilinx Video Demosaic IP
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XDEMOSAIC_AP_CTRL			(0x00)
+#define XDEMOSAIC_WIDTH				(0x10)
+#define XDEMOSAIC_HEIGHT			(0x18)
+#define XDEMOSAIC_INPUT_BAYER_FORMAT		(0x28)
+
+#define XDEMOSAIC_MIN_HEIGHT	(64)
+#define XDEMOSAIC_MAX_HEIGHT	(4320)
+#define XDEMOSAIC_DEF_HEIGHT	(720)
+#define XDEMOSAIC_MIN_WIDTH	(64)
+#define XDEMOSAIC_MAX_WIDTH	(8192)
+#define XDEMOSAIC_DEF_WIDTH	(1280)
+
+#define XDEMOSAIC_RESET_DEASSERT	(0)
+#define XDEMOSAIC_RESET_ASSERT		(1)
+#define XDEMOSAIC_START			BIT(0)
+#define XDEMOSAIC_AUTO_RESTART		BIT(7)
+#define XDEMOSAIC_STREAM_ON	(XDEMOSAIC_AUTO_RESTART | XDEMOSAIC_START)
+
+enum xdmsc_bayer_format {
+	XDEMOSAIC_RGGB = 0,
+	XDEMOSAIC_GRBG,
+	XDEMOSAIC_GBRG,
+	XDEMOSAIC_BGGR,
+};
+
+struct xdmsc_dev {
+	struct xvip_device xvip;
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+
+	enum xdmsc_bayer_format bayer_fmt;
+	struct gpio_desc *rst_gpio;
+	u32 max_width;
+	u32 max_height;
+};
+
+static inline u32 xdmsc_read(struct xdmsc_dev *xdmsc, u32 reg)
+{
+	u32 data;
+
+	data = xvip_read(&xdmsc->xvip, reg);
+	dev_dbg(xdmsc->xvip.dev,
+		"Reading 0x%x from reg offset 0x%x", data, reg);
+	return data;
+}
+
+static inline void xdmsc_write(struct xdmsc_dev *xdmsc, u32 reg, u32 data)
+{
+	xvip_write(&xdmsc->xvip, reg, data);
+	dev_dbg(xdmsc->xvip.dev,
+		"Writing 0x%x to reg offset 0x%x", data, reg);
+#ifdef DEBUG
+	if (xdmsc_read(xdmsc, reg) != data)
+		dev_err(xdmsc->xvip.dev,
+			"Wrote 0x%x does not match read back", data);
+#endif
+}
+
+static inline struct xdmsc_dev *to_xdmsc(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xdmsc_dev, xvip.subdev);
+}
+
+static struct v4l2_mbus_framefmt
+*__xdmsc_get_pad_format(struct xdmsc_dev *xdmsc,
+			struct v4l2_subdev_state *sd_state,
+			unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *get_fmt;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		get_fmt = v4l2_subdev_get_try_format(&xdmsc->xvip.subdev,
+						     sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		get_fmt = &xdmsc->formats[pad];
+		break;
+	default:
+		get_fmt = NULL;
+		break;
+	}
+
+	return get_fmt;
+}
+
+static int xdmsc_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+
+	if (!enable) {
+		dev_dbg(xdmsc->xvip.dev, "%s : Off", __func__);
+		gpiod_set_value_cansleep(xdmsc->rst_gpio,
+					 XDEMOSAIC_RESET_ASSERT);
+		gpiod_set_value_cansleep(xdmsc->rst_gpio,
+					 XDEMOSAIC_RESET_DEASSERT);
+		return 0;
+	}
+
+	xdmsc_write(xdmsc, XDEMOSAIC_WIDTH,
+		    xdmsc->formats[XVIP_PAD_SINK].width);
+	xdmsc_write(xdmsc, XDEMOSAIC_HEIGHT,
+		    xdmsc->formats[XVIP_PAD_SINK].height);
+	xdmsc_write(xdmsc, XDEMOSAIC_INPUT_BAYER_FORMAT, xdmsc->bayer_fmt);
+
+	/* Start Demosaic Video IP */
+	xdmsc_write(xdmsc, XDEMOSAIC_AP_CTRL, XDEMOSAIC_STREAM_ON);
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops xdmsc_video_ops = {
+	.s_stream = xdmsc_s_stream,
+};
+
+static int xdmsc_get_format(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_format *fmt)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+	struct v4l2_mbus_framefmt *get_fmt;
+
+	get_fmt = __xdmsc_get_pad_format(xdmsc, sd_state, fmt->pad, fmt->which);
+	if (!get_fmt)
+		return -EINVAL;
+
+	fmt->format = *get_fmt;
+
+	return 0;
+}
+
+static bool
+xdmsc_is_format_bayer(struct xdmsc_dev *xdmsc, u32 code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+	case MEDIA_BUS_FMT_SRGGB12_1X12:
+	case MEDIA_BUS_FMT_SRGGB16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_RGGB;
+		break;
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SGRBG12_1X12:
+	case MEDIA_BUS_FMT_SGRBG16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_GRBG;
+		break;
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SGBRG12_1X12:
+	case MEDIA_BUS_FMT_SGBRG16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_GBRG;
+		break;
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+	case MEDIA_BUS_FMT_SBGGR12_1X12:
+	case MEDIA_BUS_FMT_SBGGR16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_BGGR;
+		break;
+	default:
+		dev_dbg(xdmsc->xvip.dev, "Unsupported format for Sink Pad");
+		return false;
+	}
+	return true;
+}
+
+static int xdmsc_set_format(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_format *fmt)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+	struct v4l2_mbus_framefmt *__format;
+
+	__format = __xdmsc_get_pad_format(xdmsc, sd_state, fmt->pad, fmt->which);
+	if (!__format)
+		return -EINVAL;
+
+	*__format = fmt->format;
+
+	__format->width = clamp_t(unsigned int, fmt->format.width,
+				  XDEMOSAIC_MIN_WIDTH, xdmsc->max_width);
+	__format->height = clamp_t(unsigned int, fmt->format.height,
+				   XDEMOSAIC_MIN_HEIGHT, xdmsc->max_height);
+
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		if (__format->code != MEDIA_BUS_FMT_RBG888_1X24 &&
+		    __format->code != MEDIA_BUS_FMT_RBG101010_1X30 &&
+		    __format->code != MEDIA_BUS_FMT_RBG121212_1X36 &&
+		    __format->code != MEDIA_BUS_FMT_RBG161616_1X48) {
+			dev_dbg(xdmsc->xvip.dev,
+				"%s : Unsupported source media bus code format",
+				__func__);
+			__format->code = MEDIA_BUS_FMT_RBG888_1X24;
+		}
+	}
+
+	if (fmt->pad == XVIP_PAD_SINK) {
+		if (!xdmsc_is_format_bayer(xdmsc, __format->code)) {
+			dev_dbg(xdmsc->xvip.dev,
+				"Unsupported Sink Pad Media format, defaulting to RGGB");
+			__format->code = MEDIA_BUS_FMT_SRGGB8_1X8;
+		}
+	}
+
+	fmt->format = *__format;
+	return 0;
+}
+
+static int xdmsc_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xdmsc->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xdmsc->default_formats[XVIP_PAD_SOURCE];
+	return 0;
+}
+
+static int xdmsc_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static const struct v4l2_subdev_internal_ops xdmsc_internal_ops = {
+	.open = xdmsc_open,
+	.close = xdmsc_close,
+};
+
+static const struct v4l2_subdev_pad_ops xdmsc_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xdmsc_get_format,
+	.set_fmt = xdmsc_set_format,
+};
+
+static const struct v4l2_subdev_ops xdmsc_ops = {
+	.video = &xdmsc_video_ops,
+	.pad = &xdmsc_pad_ops,
+};
+
+static const struct media_entity_operations xdmsc_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static int xdmsc_parse_of(struct xdmsc_dev *xdmsc)
+{
+	struct device *dev = xdmsc->xvip.dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id = 0;
+	int rval;
+
+	rval = of_property_read_u32(node, "xlnx,max-height",
+				    &xdmsc->max_height);
+	if (rval < 0) {
+		dev_err(dev, "missing xlnx,max-height property!");
+		return -EINVAL;
+	} else if (xdmsc->max_height > XDEMOSAIC_MAX_HEIGHT ||
+		 xdmsc->max_height < XDEMOSAIC_MIN_HEIGHT) {
+		dev_err(dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	rval = of_property_read_u32(node, "xlnx,max-width",
+				    &xdmsc->max_width);
+	if (rval < 0) {
+		dev_err(dev, "missing xlnx,max-width property!");
+		return -EINVAL;
+	} else if (xdmsc->max_width > XDEMOSAIC_MAX_WIDTH ||
+		 xdmsc->max_width < XDEMOSAIC_MIN_WIDTH) {
+		dev_err(dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			rval = of_property_read_u32(port, "reg", &port_id);
+			if (rval < 0) {
+				dev_err(dev, "No reg in DT");
+				return rval;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "Invalid reg in DT");
+				return -EINVAL;
+			}
+		}
+	}
+
+	xdmsc->rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(xdmsc->rst_gpio)) {
+		if (PTR_ERR(xdmsc->rst_gpio) != -EPROBE_DEFER)
+			dev_err(dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(xdmsc->rst_gpio);
+	}
+	return 0;
+}
+
+static int xdmsc_probe(struct platform_device *pdev)
+{
+	struct xdmsc_dev *xdmsc;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *def_fmt;
+	int rval;
+
+	xdmsc = devm_kzalloc(&pdev->dev, sizeof(*xdmsc), GFP_KERNEL);
+	if (!xdmsc)
+		return -ENOMEM;
+	xdmsc->xvip.dev = &pdev->dev;
+	rval = xdmsc_parse_of(xdmsc);
+	if (rval < 0)
+		return rval;
+	rval = xvip_init_resources(&xdmsc->xvip);
+	if (rval)
+		return -EIO;
+
+	/* Reset Demosaic IP */
+	gpiod_set_value_cansleep(xdmsc->rst_gpio,
+				 XDEMOSAIC_RESET_DEASSERT);
+
+	/* Init V4L2 subdev */
+	subdev = &xdmsc->xvip.subdev;
+	v4l2_subdev_init(subdev, &xdmsc_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xdmsc_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Default Formats Initialization */
+	def_fmt = &xdmsc->default_formats[XVIP_PAD_SINK];
+	def_fmt->field = V4L2_FIELD_NONE;
+	def_fmt->colorspace = V4L2_COLORSPACE_SRGB;
+	def_fmt->width = XDEMOSAIC_DEF_WIDTH;
+	def_fmt->height = XDEMOSAIC_DEF_HEIGHT;
+
+	/*
+	 * Sink Pad can be any Bayer format.
+	 * Default Sink Pad format is RGGB.
+	 */
+	def_fmt->code = MEDIA_BUS_FMT_SRGGB8_1X8;
+	xdmsc->formats[XVIP_PAD_SINK] = *def_fmt;
+
+	def_fmt = &xdmsc->default_formats[XVIP_PAD_SOURCE];
+	*def_fmt = xdmsc->default_formats[XVIP_PAD_SINK];
+
+	/* Source Pad has a fixed media bus format of RGB */
+	def_fmt->code = MEDIA_BUS_FMT_RBG888_1X24;
+	xdmsc->formats[XVIP_PAD_SOURCE] = *def_fmt;
+
+	xdmsc->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xdmsc->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Init Media Entity */
+	subdev->entity.ops = &xdmsc_media_ops;
+	rval = media_entity_pads_init(&subdev->entity, 2, xdmsc->pads);
+	if (rval < 0)
+		goto media_error;
+
+	platform_set_drvdata(pdev, xdmsc);
+	rval = v4l2_async_register_subdev(subdev);
+	if (rval < 0) {
+		dev_err(&pdev->dev, "failed to register subdev");
+		goto v4l2_subdev_error;
+	}
+	dev_info(&pdev->dev,
+		 "Xilinx Video Demosaic Probe Successful");
+	return 0;
+
+v4l2_subdev_error:
+	media_entity_cleanup(&subdev->entity);
+media_error:
+	xvip_cleanup_resources(&xdmsc->xvip);
+	return rval;
+}
+
+static int xdmsc_remove(struct platform_device *pdev)
+{
+	struct xdmsc_dev *xdmsc = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xdmsc->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xdmsc->xvip);
+	return 0;
+}
+
+static const struct of_device_id xdmsc_of_id_table[] = {
+	{.compatible = "xlnx,v-demosaic"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xdmsc_of_id_table);
+
+static struct platform_driver xdmsc_driver = {
+	.driver = {
+		.name = "xilinx-demosaic",
+		.of_match_table = xdmsc_of_id_table,
+	},
+	.probe = xdmsc_probe,
+	.remove = xdmsc_remove,
+
+};
+
+module_platform_driver(xdmsc_driver);
+MODULE_DESCRIPTION("Xilinx Demosaic IP Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-dma.c
@@ -10,11 +10,13 @@
  */
 
 #include <linux/dma/xilinx_dma.h>
+#include <linux/dma/xilinx_frmbuf.h>
 #include <linux/lcm.h>
 #include <linux/list.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/slab.h>
+#include <linux/xilinx-v4l2-controls.h>
 
 #include <media/v4l2-dev.h>
 #include <media/v4l2-fh.h>
@@ -26,9 +28,10 @@
 #include "xilinx-vip.h"
 #include "xilinx-vipp.h"
 
+#define XVIP_DMA_DEF_FORMAT		V4L2_PIX_FMT_YUYV
 #define XVIP_DMA_DEF_WIDTH		1920
 #define XVIP_DMA_DEF_HEIGHT		1080
-
+#define XVIP_DMA_DEF_WIDTH_ALIGN	2
 /* Minimum and maximum widths are expressed in bytes */
 #define XVIP_DMA_MIN_WIDTH		1U
 #define XVIP_DMA_MAX_WIDTH		65535U
@@ -61,7 +64,7 @@
 	int ret;
 
 	subdev = xvip_dma_remote_subdev(&dma->pad, &fmt.pad);
-	if (subdev == NULL)
+	if (!subdev)
 		return -EPIPE;
 
 	fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
@@ -69,10 +72,15 @@
 	if (ret < 0)
 		return ret == -ENOIOCTLCMD ? -EINVAL : ret;
 
-	if (dma->fmtinfo->code != fmt.format.code ||
-	    dma->format.height != fmt.format.height ||
-	    dma->format.width != fmt.format.width ||
-	    dma->format.colorspace != fmt.format.colorspace)
+	if (dma->fmtinfo->code != fmt.format.code)
+		return -EINVAL;
+
+	/*
+	 * Crop rectangle contains format resolution by default, and crop
+	 * rectangle if s_selection is executed.
+	 */
+	if (dma->r.width != fmt.format.width ||
+	    dma->r.height != fmt.format.height)
 		return -EINVAL;
 
 	return 0;
@@ -83,46 +91,6 @@
  */
 
 /**
- * xvip_pipeline_start_stop - Start ot stop streaming on a pipeline
- * @pipe: The pipeline
- * @start: Start (when true) or stop (when false) the pipeline
- *
- * Walk the entities chain starting at the pipeline output video node and start
- * or stop all of them.
- *
- * Return: 0 if successful, or the return value of the failed video::s_stream
- * operation otherwise.
- */
-static int xvip_pipeline_start_stop(struct xvip_pipeline *pipe, bool start)
-{
-	struct xvip_dma *dma = pipe->output;
-	struct media_entity *entity;
-	struct media_pad *pad;
-	struct v4l2_subdev *subdev;
-	int ret;
-
-	entity = &dma->video.entity;
-	while (1) {
-		pad = &entity->pads[0];
-		if (!(pad->flags & MEDIA_PAD_FL_SINK))
-			break;
-
-		pad = media_entity_remote_pad(pad);
-		if (!pad || !is_media_entity_v4l2_subdev(pad->entity))
-			break;
-
-		entity = pad->entity;
-		subdev = media_entity_to_v4l2_subdev(entity);
-
-		ret = v4l2_subdev_call(subdev, video, s_stream, start);
-		if (start && ret < 0 && ret != -ENOIOCTLCMD)
-			return ret;
-	}
-
-	return 0;
-}
-
-/**
  * xvip_pipeline_set_stream - Enable/disable streaming on a pipeline
  * @pipe: The pipeline
  * @on: Turn the stream on when true or off when false
@@ -132,7 +100,8 @@
  * independently, pipelines have a shared stream state that enable or disable
  * all entities in the pipeline. For this reason the pipeline uses a streaming
  * counter that tracks the number of DMA engines that have requested the stream
- * to be enabled.
+ * to be enabled. This will walk the graph starting from each DMA and enable or
+ * disable the entities in the path.
  *
  * When called with the @on argument set to true, this function will increment
  * the pipeline streaming count. If the streaming count reaches the number of
@@ -149,20 +118,22 @@
  */
 static int xvip_pipeline_set_stream(struct xvip_pipeline *pipe, bool on)
 {
+	struct xvip_composite_device *xdev;
 	int ret = 0;
 
 	mutex_lock(&pipe->lock);
+	xdev = pipe->xdev;
 
 	if (on) {
-		if (pipe->stream_count == pipe->num_dmas - 1) {
-			ret = xvip_pipeline_start_stop(pipe, true);
+		if (pipe->stream_count == pipe->num_dmas - 1 || xdev->atomic_streamon) {
+			ret = xvip_graph_pipeline_start_stop(xdev, pipe, true);
 			if (ret < 0)
 				goto done;
 		}
 		pipe->stream_count++;
 	} else {
 		if (--pipe->stream_count == 0)
-			xvip_pipeline_start_stop(pipe, false);
+			xvip_graph_pipeline_start_stop(xdev, pipe, false);
 	}
 
 done:
@@ -199,23 +170,22 @@
 
 		dma = to_xvip_dma(media_entity_to_video_device(entity));
 
-		if (dma->pad.flags & MEDIA_PAD_FL_SINK) {
-			pipe->output = dma;
+		if (dma->pad.flags & MEDIA_PAD_FL_SINK)
 			num_outputs++;
-		} else {
+		else
 			num_inputs++;
-		}
 	}
 
 	mutex_unlock(&mdev->graph_mutex);
 
 	media_graph_walk_cleanup(&graph);
 
-	/* We need exactly one output and zero or one input. */
-	if (num_outputs != 1 || num_inputs > 1)
+	/* We need at least one DMA to proceed */
+	if (num_outputs == 0 && num_inputs == 0)
 		return -EPIPE;
 
 	pipe->num_dmas = num_inputs + num_outputs;
+	pipe->xdev = start->xdev;
 
 	return 0;
 }
@@ -223,7 +193,6 @@
 static void __xvip_pipeline_cleanup(struct xvip_pipeline *pipe)
 {
 	pipe->num_dmas = 0;
-	pipe->output = NULL;
 }
 
 /**
@@ -286,11 +255,13 @@
  * @buf: vb2 buffer base object
  * @queue: buffer list entry in the DMA engine queued buffers list
  * @dma: DMA channel that uses the buffer
+ * @desc: Descriptor associated with this structure
  */
 struct xvip_dma_buffer {
 	struct vb2_v4l2_buffer buf;
 	struct list_head queue;
 	struct xvip_dma *dma;
+	struct dma_async_tx_descriptor *desc;
 };
 
 #define to_xvip_dma_buffer(vb)	container_of(vb, struct xvip_dma_buffer, buf)
@@ -299,6 +270,9 @@
 {
 	struct xvip_dma_buffer *buf = param;
 	struct xvip_dma *dma = buf->dma;
+	int i, sizeimage;
+	u32 fid;
+	int status;
 
 	spin_lock(&dma->queued_lock);
 	list_del(&buf->queue);
@@ -307,7 +281,38 @@
 	buf->buf.field = V4L2_FIELD_NONE;
 	buf->buf.sequence = dma->sequence++;
 	buf->buf.vb2_buf.timestamp = ktime_get_ns();
-	vb2_set_plane_payload(&buf->buf.vb2_buf, 0, dma->format.sizeimage);
+
+	status = xilinx_xdma_get_fid(dma->dma, buf->desc, &fid);
+	if (!status) {
+		if (((V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) &&
+		     dma->format.fmt.pix_mp.field == V4L2_FIELD_ALTERNATE) ||
+		     dma->format.fmt.pix.field == V4L2_FIELD_ALTERNATE) {
+			/*
+			 * fid = 1 is odd field i.e. V4L2_FIELD_TOP.
+			 * fid = 0 is even field i.e. V4L2_FIELD_BOTTOM.
+			 */
+			buf->buf.field = fid ?
+					 V4L2_FIELD_TOP : V4L2_FIELD_BOTTOM;
+
+			if (fid == dma->prev_fid)
+				buf->buf.sequence = dma->sequence++;
+
+			buf->buf.sequence >>= 1;
+			dma->prev_fid = fid;
+		}
+	}
+
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+		for (i = 0; i < dma->fmtinfo->buffers; i++) {
+			sizeimage =
+				dma->format.fmt.pix_mp.plane_fmt[i].sizeimage;
+			vb2_set_plane_payload(&buf->buf.vb2_buf, i, sizeimage);
+		}
+	} else {
+		sizeimage = dma->format.fmt.pix.sizeimage;
+		vb2_set_plane_payload(&buf->buf.vb2_buf, 0, sizeimage);
+	}
+
 	vb2_buffer_done(&buf->buf.vb2_buf, VB2_BUF_STATE_DONE);
 }
 
@@ -317,13 +322,39 @@
 		     unsigned int sizes[], struct device *alloc_devs[])
 {
 	struct xvip_dma *dma = vb2_get_drv_priv(vq);
+	unsigned int i;
+	int sizeimage;
+
+	/* Multi planar case: Make sure the image size is large enough */
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+		if (*nplanes) {
+			if (*nplanes != dma->format.fmt.pix_mp.num_planes)
+				return -EINVAL;
+
+			for (i = 0; i < *nplanes; i++) {
+				sizeimage =
+				  dma->format.fmt.pix_mp.plane_fmt[i].sizeimage;
+				if (sizes[i] < sizeimage)
+					return -EINVAL;
+			}
+		} else {
+			*nplanes = dma->fmtinfo->buffers;
+			for (i = 0; i < dma->fmtinfo->buffers; i++) {
+				sizeimage =
+				  dma->format.fmt.pix_mp.plane_fmt[i].sizeimage;
+				sizes[i] = sizeimage;
+			}
+		}
+		return 0;
+	}
 
-	/* Make sure the image size is large enough. */
-	if (*nplanes)
-		return sizes[0] < dma->format.sizeimage ? -EINVAL : 0;
+	/* Single planar case: Make sure the image size is large enough */
+	sizeimage = dma->format.fmt.pix.sizeimage;
+	if (*nplanes == 1)
+		return sizes[0] < sizeimage ? -EINVAL : 0;
 
 	*nplanes = 1;
-	sizes[0] = dma->format.sizeimage;
+	sizes[0] = sizeimage;
 
 	return 0;
 }
@@ -346,15 +377,21 @@
 	struct xvip_dma_buffer *buf = to_xvip_dma_buffer(vbuf);
 	struct dma_async_tx_descriptor *desc;
 	dma_addr_t addr = vb2_dma_contig_plane_dma_addr(vb, 0);
-	u32 flags;
+	u32 flags = 0;
+	u32 luma_size;
+	u32 padding_factor_nume, padding_factor_deno, bpl_nume, bpl_deno;
+	u32 fid = ~0;
+	u32 bpl;
 
-	if (dma->queue.type == V4L2_BUF_TYPE_VIDEO_CAPTURE) {
+	if (dma->queue.type == V4L2_BUF_TYPE_VIDEO_CAPTURE ||
+	    dma->queue.type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE) {
 		flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
 		dma->xt.dir = DMA_DEV_TO_MEM;
 		dma->xt.src_sgl = false;
 		dma->xt.dst_sgl = true;
 		dma->xt.dst_start = addr;
-	} else {
+	} else if (dma->queue.type == V4L2_BUF_TYPE_VIDEO_OUTPUT ||
+		   dma->queue.type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE) {
 		flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
 		dma->xt.dir = DMA_MEM_TO_DEV;
 		dma->xt.src_sgl = true;
@@ -362,10 +399,89 @@
 		dma->xt.src_start = addr;
 	}
 
-	dma->xt.frame_size = 1;
-	dma->sgl[0].size = dma->format.width * dma->fmtinfo->bpp;
-	dma->sgl[0].icg = dma->format.bytesperline - dma->sgl[0].size;
-	dma->xt.numf = dma->format.height;
+	/*
+	 * DMA IP supports only 2 planes, so one datachunk is sufficient
+	 * to get start address of 2nd plane
+	 */
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+		struct v4l2_pix_format_mplane *pix_mp;
+		size_t size;
+
+		pix_mp = &dma->format.fmt.pix_mp;
+		bpl = pix_mp->plane_fmt[0].bytesperline;
+
+		xilinx_xdma_v4l2_config(dma->dma, pix_mp->pixelformat);
+		xvip_width_padding_factor(pix_mp->pixelformat,
+					  &padding_factor_nume,
+					  &padding_factor_deno);
+		xvip_bpl_scaling_factor(pix_mp->pixelformat, &bpl_nume,
+					&bpl_deno);
+		dma->xt.frame_size = dma->fmtinfo->num_planes;
+
+		size = ((size_t)dma->r.width * dma->fmtinfo->bpl_factor *
+			padding_factor_nume * bpl_nume) /
+			((size_t)padding_factor_deno * bpl_deno);
+		dma->sgl[0].size = size;
+
+		dma->sgl[0].icg = bpl - dma->sgl[0].size;
+		dma->xt.numf = dma->r.height;
+
+		/*
+		 * dst_icg is the number of bytes to jump after last luma addr
+		 * and before first chroma addr
+		 */
+
+		/* Handling contiguous data with mplanes */
+		if (dma->fmtinfo->buffers == 1) {
+			dma->sgl[0].dst_icg = (size_t)bpl *
+					      (pix_mp->height - dma->r.height);
+		} else {
+			/* Handling non-contiguous data with mplanes */
+			if (dma->fmtinfo->buffers == 2 || dma->fmtinfo->buffers == 3) {
+				dma_addr_t chroma_addr =
+					vb2_dma_contig_plane_dma_addr(vb, 1);
+				luma_size = bpl * dma->xt.numf;
+				if (chroma_addr > addr)
+					dma->sgl[0].dst_icg = chroma_addr -
+						addr - luma_size;
+			}
+			/* Handle the 3rd plane for Y_U_V8 */
+			if (dma->fmtinfo->buffers == 3) {
+				dma_addr_t chroma_addr =
+					vb2_dma_contig_plane_dma_addr(vb, 1);
+				dma_addr_t third_plane_addr =
+					vb2_dma_contig_plane_dma_addr(vb, 2);
+				u32 chroma_size = bpl * dma->xt.numf;
+
+				if (third_plane_addr > chroma_addr)
+					dma->sgl[0].dst_icg = third_plane_addr -
+						chroma_addr - chroma_size;
+			}
+		}
+	} else {
+		struct v4l2_pix_format *pix;
+		size_t size;
+		size_t dst_icg;
+
+		pix = &dma->format.fmt.pix;
+		bpl = pix->bytesperline;
+		xilinx_xdma_v4l2_config(dma->dma, pix->pixelformat);
+		xvip_width_padding_factor(pix->pixelformat,
+					  &padding_factor_nume,
+					  &padding_factor_deno);
+		xvip_bpl_scaling_factor(pix->pixelformat, &bpl_nume,
+					&bpl_deno);
+		dma->xt.frame_size = dma->fmtinfo->num_planes;
+		size = ((size_t)dma->r.width * dma->fmtinfo->bpl_factor *
+			padding_factor_nume * bpl_nume) /
+			((size_t)padding_factor_deno * bpl_deno);
+		dma->sgl[0].size = size;
+		dma->sgl[0].icg = bpl - dma->sgl[0].size;
+		dma->xt.numf = dma->r.height;
+		dma->sgl[0].dst_icg = 0;
+		dst_icg = (size_t)bpl * (pix->height - dma->r.height);
+		dma->sgl[0].dst_icg = dst_icg;
+	}
 
 	desc = dmaengine_prep_interleaved_dma(dma->dma, &dma->xt, flags);
 	if (!desc) {
@@ -375,11 +491,28 @@
 	}
 	desc->callback = xvip_dma_complete;
 	desc->callback_param = buf;
+	buf->desc = desc;
+
+	if (buf->buf.field == V4L2_FIELD_TOP)
+		fid = 1;
+	else if (buf->buf.field == V4L2_FIELD_BOTTOM)
+		fid = 0;
+	else if (buf->buf.field == V4L2_FIELD_NONE)
+		fid = 0;
+
+	xilinx_xdma_set_fid(dma->dma, desc, fid);
 
 	spin_lock_irq(&dma->queued_lock);
 	list_add_tail(&buf->queue, &dma->queued_bufs);
 	spin_unlock_irq(&dma->queued_lock);
 
+	/*
+	 * Low latency capture: Give descriptor callback at start of
+	 * processing the descriptor
+	 */
+	if (dma->low_latency_cap)
+		xilinx_xdma_set_earlycb(dma->dma, desc,
+					EARLY_CALLBACK_START_DESC);
 	dmaengine_submit(desc);
 
 	if (vb2_is_streaming(&dma->queue))
@@ -394,6 +527,7 @@
 	int ret;
 
 	dma->sequence = 0;
+	dma->prev_fid = ~0;
 
 	/*
 	 * Start streaming on the pipeline. No link touching an entity in the
@@ -402,10 +536,12 @@
 	 * Use the pipeline object embedded in the first DMA object that starts
 	 * streaming.
 	 */
+	mutex_lock(&dma->xdev->lock);
 	pipe = dma->video.entity.pipe
 	     ? to_xvip_pipeline(&dma->video.entity) : &dma->pipe;
 
 	ret = media_pipeline_start(&dma->video.entity, &pipe->pipe);
+	mutex_unlock(&dma->xdev->lock);
 	if (ret < 0)
 		goto error;
 
@@ -422,11 +558,25 @@
 
 	/* Start the DMA engine. This must be done before starting the blocks
 	 * in the pipeline to avoid DMA synchronization issues.
+	 * We dont't want to start DMA in case of low latency capture mode,
+	 * applications will start DMA using S_CTRL at later point of time.
 	 */
-	dma_async_issue_pending(dma->dma);
+	if (!dma->low_latency_cap) {
+		dma_async_issue_pending(dma->dma);
+	} else {
+		/* For low latency capture, return the first buffer early
+		 * so that consumer can initialize until we start DMA.
+		 */
+		buf = list_first_entry(&dma->queued_bufs,
+				       struct xvip_dma_buffer, queue);
+		xvip_dma_complete(buf);
+		buf->desc->callback = NULL;
+	}
 
 	/* Start the pipeline. */
-	xvip_pipeline_set_stream(pipe, true);
+	ret = xvip_pipeline_set_stream(pipe, true);
+	if (ret < 0)
+		goto error_stop;
 
 	return 0;
 
@@ -434,6 +584,7 @@
 	media_pipeline_stop(&dma->video.entity);
 
 error:
+	dmaengine_terminate_all(dma->dma);
 	/* Give back all queued buffers to videobuf2. */
 	spin_lock_irq(&dma->queued_lock);
 	list_for_each_entry_safe(buf, nbuf, &dma->queued_bufs, queue) {
@@ -493,10 +644,104 @@
 	cap->capabilities = dma->xdev->v4l2_caps | V4L2_CAP_STREAMING |
 			    V4L2_CAP_DEVICE_CAPS;
 
-	strscpy(cap->driver, "xilinx-vipp", sizeof(cap->driver));
-	strscpy(cap->card, dma->video.name, sizeof(cap->card));
-	snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%pOFn:%u",
-		 dma->xdev->dev->of_node, dma->port);
+	strscpy((char *)cap->driver, "xilinx-vipp", sizeof(cap->driver));
+	strscpy((char *)cap->card, (char *)dma->video.name, sizeof(cap->card));
+	snprintf((char *)cap->bus_info, sizeof(cap->bus_info),
+		 "platform:%pOFn:%u", dma->xdev->dev->of_node, dma->port);
+
+	return 0;
+}
+
+static int xvip_xdma_enum_fmt(struct xvip_dma *dma, struct v4l2_fmtdesc *f,
+			      struct v4l2_subdev_format *v4l_fmt)
+{
+	const struct xvip_video_format *fmt;
+	int ret;
+	u32 i, fmt_cnt, *fmts;
+
+	ret = xilinx_xdma_get_v4l2_vid_fmts(dma->dma, &fmt_cnt, &fmts);
+	if (ret)
+		return ret;
+
+	/* Has media pad value changed? */
+	if (v4l_fmt->format.code != dma->remote_subdev_med_bus ||
+	    !dma->remote_subdev_med_bus) {
+		/* Re-generate legal list of fourcc codes */
+		dma->poss_v4l2_fmt_cnt = 0;
+		dma->remote_subdev_med_bus = v4l_fmt->format.code;
+
+		if (!dma->poss_v4l2_fmts) {
+			dma->poss_v4l2_fmts =
+				devm_kzalloc(&dma->video.dev,
+					     sizeof(u32) * fmt_cnt,
+					     GFP_KERNEL);
+			if (!dma->poss_v4l2_fmts)
+				return -ENOMEM;
+		}
+
+		for (i = 0; i < fmt_cnt; i++) {
+			fmt = xvip_get_format_by_fourcc(fmts[i]);
+			if (IS_ERR(fmt))
+				return PTR_ERR(fmt);
+
+			if (fmt->code != dma->remote_subdev_med_bus)
+				continue;
+
+			dma->poss_v4l2_fmts[dma->poss_v4l2_fmt_cnt++] =	fmts[i];
+		}
+	}
+
+	/* Return err if index is greater than count of legal values */
+	if (f->index >= dma->poss_v4l2_fmt_cnt)
+		return -EINVAL;
+
+	/* Else return pix format in table */
+	fmt = xvip_get_format_by_fourcc(dma->poss_v4l2_fmts[f->index]);
+	if (IS_ERR(fmt))
+		return PTR_ERR(fmt);
+
+	f->pixelformat = fmt->fourcc;
+
+	return 0;
+}
+
+static int
+xvip_dma_enum_input(struct file *file, void *priv, struct v4l2_input *i)
+{
+	struct v4l2_fh *vfh = file->private_data;
+	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
+	struct v4l2_subdev *subdev;
+
+	if (i->index > 0)
+		return -EINVAL;
+
+	subdev = xvip_dma_remote_subdev(&dma->pad, NULL);
+	if (!subdev)
+		return -EPIPE;
+
+	/*
+	 * FIXME: right now only camera input type is handled.
+	 * There should be mechanism to distinguish other types of
+	 * input like V4L2_INPUT_TYPE_TUNER and V4L2_INPUT_TYPE_TOUCH.
+	 */
+	i->type = V4L2_INPUT_TYPE_CAMERA;
+	strlcpy((char *)i->name, (char *)subdev->name, sizeof(i->name));
+
+	return 0;
+}
+
+static int
+xvip_dma_get_input(struct file *file, void *fh, unsigned int *i)
+{
+	*i = 0;
+	return 0;
+}
+
+static int
+xvip_dma_set_input(struct file *file, void *fh, unsigned int i)
+{
+	if (i > 0)
+		return -EINVAL;
 
 	return 0;
 }
@@ -511,11 +756,43 @@
 {
 	struct v4l2_fh *vfh = file->private_data;
 	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
+	struct v4l2_subdev *subdev;
+	struct v4l2_subdev_format v4l_fmt;
+	const struct xvip_video_format *fmt;
+	int err, ret;
+
+	/* Establish media pad format */
+	subdev = xvip_dma_remote_subdev(&dma->pad, &v4l_fmt.pad);
+	if (!subdev)
+		return -EPIPE;
 
+	v4l_fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(subdev, pad, get_fmt, NULL, &v4l_fmt);
+	if (ret < 0)
+		return ret == -ENOIOCTLCMD ? -EINVAL : ret;
+
+	/*
+	 * In case of frmbuf DMA, this will invoke frambuf driver specific APIs
+	 * to enumerate formats otherwise return the pix format corresponding
+	 * to subdev's media bus format. This kind of separation would be
+	 * helpful for clean up and upstreaming.
+	 */
+	err = xvip_xdma_enum_fmt(dma, f, &v4l_fmt);
+	if (!err)
+		return err;
+
+	/*
+	 * This logic will just return one pix format based on subdev's
+	 * media bus format
+	 */
 	if (f->index > 0)
 		return -EINVAL;
 
-	f->pixelformat = dma->format.pixelformat;
+	fmt = xvip_get_format_by_code(v4l_fmt.format.code);
+	if (IS_ERR(fmt))
+		return PTR_ERR(fmt);
+
+	f->pixelformat = fmt->fourcc;
 
 	return 0;
 }
@@ -526,13 +803,17 @@
 	struct v4l2_fh *vfh = file->private_data;
 	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
 
-	format->fmt.pix = dma->format;
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type))
+		format->fmt.pix_mp = dma->format.fmt.pix_mp;
+	else
+		format->fmt.pix = dma->format.fmt.pix;
 
 	return 0;
 }
 
 static void
-__xvip_dma_try_format(struct xvip_dma *dma, struct v4l2_pix_format *pix,
+__xvip_dma_try_format(struct xvip_dma *dma,
+		      struct v4l2_format *format,
 		      const struct xvip_video_format **fmtinfo)
 {
 	const struct xvip_video_format *info;
@@ -541,40 +822,146 @@
 	unsigned int min_bpl;
 	unsigned int max_bpl;
 	unsigned int width;
-	unsigned int align;
 	unsigned int bpl;
+	unsigned int i, hsub, vsub, plane_width, plane_height;
+	unsigned int fourcc;
+	unsigned int padding_factor_nume, padding_factor_deno;
+	unsigned int bpl_nume, bpl_deno;
+	struct v4l2_subdev_format fmt;
+	struct v4l2_subdev *subdev;
+	int ret;
+
+	subdev = xvip_dma_remote_subdev(&dma->pad, &fmt.pad);
+	if (!subdev)
+		return;
+
+	fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(subdev, pad, get_fmt, NULL, &fmt);
+	if (ret < 0)
+		return;
+
+	if (fmt.format.field == V4L2_FIELD_ALTERNATE) {
+		if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type))
+			dma->format.fmt.pix_mp.field = V4L2_FIELD_ALTERNATE;
+		else
+			dma->format.fmt.pix.field = V4L2_FIELD_ALTERNATE;
+	} else {
+		if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type))
+			dma->format.fmt.pix_mp.field = V4L2_FIELD_NONE;
+		else
+			dma->format.fmt.pix.field = V4L2_FIELD_NONE;
+	}
 
 	/* Retrieve format information and select the default format if the
 	 * requested format isn't supported.
 	 */
-	info = xvip_get_format_by_fourcc(pix->pixelformat);
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type))
+		fourcc = format->fmt.pix_mp.pixelformat;
+	else
+		fourcc = format->fmt.pix.pixelformat;
+
+	info = xvip_get_format_by_fourcc(fourcc);
 
-	pix->pixelformat = info->fourcc;
-	pix->field = V4L2_FIELD_NONE;
+	if (IS_ERR(info))
+		info = xvip_get_format_by_fourcc(XVIP_DMA_DEF_FORMAT);
+
+	xvip_width_padding_factor(info->fourcc, &padding_factor_nume,
+				  &padding_factor_deno);
+	xvip_bpl_scaling_factor(info->fourcc, &bpl_nume, &bpl_deno);
 
 	/* The transfer alignment requirements are expressed in bytes. Compute
 	 * the minimum and maximum values, clamp the requested width and convert
 	 * it back to pixels.
 	 */
-	align = lcm(dma->align, info->bpp);
-	min_width = roundup(XVIP_DMA_MIN_WIDTH, align);
-	max_width = rounddown(XVIP_DMA_MAX_WIDTH, align);
-	width = rounddown(pix->width * info->bpp, align);
-
-	pix->width = clamp(width, min_width, max_width) / info->bpp;
-	pix->height = clamp(pix->height, XVIP_DMA_MIN_HEIGHT,
-			    XVIP_DMA_MAX_HEIGHT);
-
-	/* Clamp the requested bytes per line value. If the maximum bytes per
-	 * line value is zero, the module doesn't support user configurable line
-	 * sizes. Override the requested value with the minimum in that case.
-	 */
-	min_bpl = pix->width * info->bpp;
-	max_bpl = rounddown(XVIP_DMA_MAX_WIDTH, dma->align);
-	bpl = rounddown(pix->bytesperline, dma->align);
+	min_width = roundup(XVIP_DMA_MIN_WIDTH, dma->width_align);
+	max_width = rounddown(XVIP_DMA_MAX_WIDTH, dma->width_align);
 
-	pix->bytesperline = clamp(bpl, min_bpl, max_bpl);
-	pix->sizeimage = pix->bytesperline * pix->height;
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+		struct v4l2_pix_format_mplane *pix_mp;
+		struct v4l2_plane_pix_format *plane_fmt;
+
+		pix_mp = &format->fmt.pix_mp;
+		plane_fmt = pix_mp->plane_fmt;
+		pix_mp->field = dma->format.fmt.pix_mp.field;
+		width = rounddown(pix_mp->width * info->bpl_factor,
+				  dma->width_align);
+		pix_mp->width = clamp(width, min_width, max_width) /
+				info->bpl_factor;
+		pix_mp->height = clamp(pix_mp->height, XVIP_DMA_MIN_HEIGHT,
+				       XVIP_DMA_MAX_HEIGHT);
+
+		/*
+		 * Clamp the requested bytes per line value. If the maximum
+		 * bytes per line value is zero, the module doesn't support
+		 * user configurable line sizes. Override the requested value
+		 * with the minimum in that case.
+		 */
+
+		max_bpl = rounddown(XVIP_DMA_MAX_WIDTH, dma->align);
+
+		/* Handling contiguous data with mplanes */
+		if (info->buffers == 1) {
+			min_bpl = (pix_mp->width * info->bpl_factor *
+				   padding_factor_nume * bpl_nume) /
+				   (padding_factor_deno * bpl_deno);
+			min_bpl = roundup(min_bpl, dma->align);
+			bpl = roundup(plane_fmt[0].bytesperline, dma->align);
+			plane_fmt[0].bytesperline = clamp(bpl, min_bpl,
+							  max_bpl);
+
+			if (info->num_planes == 1) {
+				/* Single plane formats */
+				plane_fmt[0].sizeimage =
+						plane_fmt[0].bytesperline *
+						pix_mp->height;
+			} else {
+				/* Multi plane formats */
+				plane_fmt[0].sizeimage =
+					DIV_ROUND_UP(plane_fmt[0].bytesperline *
+						     pix_mp->height *
+						     info->bpp, 8);
+			}
+		} else {
+			/* Handling non-contiguous data with mplanes */
+			hsub = info->hsub;
+			vsub = info->vsub;
+			for (i = 0; i < info->num_planes; i++) {
+				plane_width = pix_mp->width / (i ? hsub : 1);
+				plane_height = pix_mp->height / (i ? vsub : 1);
+				min_bpl = (plane_width * info->bpl_factor *
+					   padding_factor_nume * bpl_nume) /
+					   (padding_factor_deno * bpl_deno);
+				min_bpl = roundup(min_bpl, dma->align);
+				bpl = rounddown(plane_fmt[i].bytesperline,
+						dma->align);
+				plane_fmt[i].bytesperline =
+						clamp(bpl, min_bpl, max_bpl);
+				plane_fmt[i].sizeimage =
+						plane_fmt[i].bytesperline *
+						plane_height;
+			}
+		}
+	} else {
+		struct v4l2_pix_format *pix;
+
+		pix = &format->fmt.pix;
+		pix->field = dma->format.fmt.pix.field;
+		width = rounddown(pix->width * info->bpl_factor,
+				  dma->width_align);
+		pix->width = clamp(width, min_width, max_width) /
+			     info->bpl_factor;
+		pix->height = clamp(pix->height, XVIP_DMA_MIN_HEIGHT,
+				    XVIP_DMA_MAX_HEIGHT);
+
+		min_bpl = (pix->width * info->bpl_factor *
+			  padding_factor_nume * bpl_nume) /
+			  (padding_factor_deno * bpl_deno);
+		min_bpl = roundup(min_bpl, dma->align);
+		max_bpl = rounddown(XVIP_DMA_MAX_WIDTH, dma->align);
+		bpl = rounddown(pix->bytesperline, dma->align);
+		pix->bytesperline = clamp(bpl, min_bpl, max_bpl);
+		pix->sizeimage = pix->width * pix->height * info->bpp / 8;
+	}
 
 	if (fmtinfo)
 		*fmtinfo = info;
@@ -586,7 +973,7 @@
 	struct v4l2_fh *vfh = file->private_data;
 	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
 
-	__xvip_dma_try_format(dma, &format->fmt.pix, NULL);
+	__xvip_dma_try_format(dma, format, NULL);
 	return 0;
 }
 
@@ -597,26 +984,149 @@
 	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
 	const struct xvip_video_format *info;
 
-	__xvip_dma_try_format(dma, &format->fmt.pix, &info);
+	__xvip_dma_try_format(dma, format, &info);
 
 	if (vb2_is_busy(&dma->queue))
 		return -EBUSY;
 
-	dma->format = format->fmt.pix;
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+		dma->format.fmt.pix_mp = format->fmt.pix_mp;
+
+		/*
+		 * Save format resolution in crop rectangle. This will be
+		 * updated when s_slection is called.
+		 */
+		dma->r.width = format->fmt.pix_mp.width;
+		dma->r.height = format->fmt.pix_mp.height;
+	} else {
+		dma->format.fmt.pix = format->fmt.pix;
+		dma->r.width = format->fmt.pix.width;
+		dma->r.height = format->fmt.pix.height;
+	}
+
 	dma->fmtinfo = info;
 
 	return 0;
 }
 
+static int
+xvip_dma_g_selection(struct file *file, void *fh, struct v4l2_selection *sel)
+{
+	struct v4l2_fh *vfh = file->private_data;
+	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
+	u32 width, height;
+	bool crop_frame = false;
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_COMPOSE:
+		if (sel->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+			return -EINVAL;
+
+		crop_frame = true;
+		break;
+	case V4L2_SEL_TGT_COMPOSE_BOUNDS:
+	case V4L2_SEL_TGT_COMPOSE_DEFAULT:
+		if (sel->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+			return -EINVAL;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		if (sel->type != V4L2_BUF_TYPE_VIDEO_OUTPUT)
+			return -EINVAL;
+
+		crop_frame = true;
+		break;
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+	case V4L2_SEL_TGT_CROP_DEFAULT:
+		if (sel->type != V4L2_BUF_TYPE_VIDEO_OUTPUT)
+			return -EINVAL;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	sel->r.left = 0;
+	sel->r.top = 0;
+
+	if (crop_frame) {
+		sel->r.width = dma->r.width;
+		sel->r.height = dma->r.height;
+	} else {
+		if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+			width = dma->format.fmt.pix_mp.width;
+			height = dma->format.fmt.pix_mp.height;
+		} else {
+			width = dma->format.fmt.pix.width;
+			height = dma->format.fmt.pix.height;
+		}
+
+		sel->r.width = width;
+		sel->r.height = height;
+	}
+
+	return 0;
+}
+
+static int
+xvip_dma_s_selection(struct file *file, void *fh, struct v4l2_selection *sel)
+{
+	struct v4l2_fh *vfh = file->private_data;
+	struct xvip_dma *dma = to_xvip_dma(vfh->vdev);
+	u32 width, height;
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_COMPOSE:
+		/* COMPOSE target is only valid for capture buftype */
+		if (sel->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+			return -EINVAL;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		/* CROP target is only valid for output buftype */
+		if (sel->type != V4L2_BUF_TYPE_VIDEO_OUTPUT)
+			return -EINVAL;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->format.type)) {
+		width = dma->format.fmt.pix_mp.width;
+		height = dma->format.fmt.pix_mp.height;
+	} else {
+		width = dma->format.fmt.pix.width;
+		height = dma->format.fmt.pix.height;
+	}
+
+	if (sel->r.width > width || sel->r.height > height ||
+	    sel->r.top != 0 || sel->r.left != 0)
+		return -EINVAL;
+
+	sel->r.width = rounddown(max(XVIP_DMA_MIN_WIDTH, sel->r.width),
+				 dma->width_align);
+	sel->r.height = max(XVIP_DMA_MIN_HEIGHT, sel->r.height);
+	dma->r.width = sel->r.width;
+	dma->r.height = sel->r.height;
+
+	return 0;
+}
+
 static const struct v4l2_ioctl_ops xvip_dma_ioctl_ops = {
 	.vidioc_querycap		= xvip_dma_querycap,
 	.vidioc_enum_fmt_vid_cap	= xvip_dma_enum_format,
+	.vidioc_enum_fmt_vid_out	= xvip_dma_enum_format,
 	.vidioc_g_fmt_vid_cap		= xvip_dma_get_format,
+	.vidioc_g_fmt_vid_cap_mplane	= xvip_dma_get_format,
 	.vidioc_g_fmt_vid_out		= xvip_dma_get_format,
+	.vidioc_g_fmt_vid_out_mplane	= xvip_dma_get_format,
 	.vidioc_s_fmt_vid_cap		= xvip_dma_set_format,
+	.vidioc_s_fmt_vid_cap_mplane	= xvip_dma_set_format,
 	.vidioc_s_fmt_vid_out		= xvip_dma_set_format,
+	.vidioc_s_fmt_vid_out_mplane	= xvip_dma_set_format,
 	.vidioc_try_fmt_vid_cap		= xvip_dma_try_format,
+	.vidioc_try_fmt_vid_cap_mplane	= xvip_dma_try_format,
 	.vidioc_try_fmt_vid_out		= xvip_dma_try_format,
+	.vidioc_try_fmt_vid_out_mplane	= xvip_dma_try_format,
+	.vidioc_s_selection		= xvip_dma_s_selection,
+	.vidioc_g_selection		= xvip_dma_g_selection,
 	.vidioc_reqbufs			= vb2_ioctl_reqbufs,
 	.vidioc_querybuf		= vb2_ioctl_querybuf,
 	.vidioc_qbuf			= vb2_ioctl_qbuf,
@@ -625,6 +1135,99 @@
 	.vidioc_expbuf			= vb2_ioctl_expbuf,
 	.vidioc_streamon		= vb2_ioctl_streamon,
 	.vidioc_streamoff		= vb2_ioctl_streamoff,
+	.vidioc_enum_input	= &xvip_dma_enum_input,
+	.vidioc_g_input		= &xvip_dma_get_input,
+	.vidioc_s_input		= &xvip_dma_set_input,
+};
+
+/* -----------------------------------------------------------------------------
+ * V4L2 controls
+ */
+
+static int xvip_dma_s_ctrl(struct v4l2_ctrl *ctl)
+{
+	struct xvip_dma *dma = container_of(ctl->handler, struct xvip_dma,
+					    ctrl_handler);
+	int ret = 0;
+
+	switch (ctl->id)  {
+	case V4L2_CID_XILINX_LOW_LATENCY:
+		if (ctl->val == XVIP_LOW_LATENCY_ENABLE) {
+			if (vb2_is_busy(&dma->queue))
+				return -EBUSY;
+
+			dma->low_latency_cap = true;
+			/*
+			 * Don't use auto-restart for low latency
+			 * to avoid extra one frame delay between
+			 * programming and actual writing of data
+			 */
+			xilinx_xdma_set_mode(dma->dma, DEFAULT);
+		} else if (ctl->val == XVIP_LOW_LATENCY_DISABLE) {
+			if (vb2_is_busy(&dma->queue))
+				return -EBUSY;
+
+			dma->low_latency_cap = false;
+			xilinx_xdma_set_mode(dma->dma, AUTO_RESTART);
+		} else if (ctl->val == XVIP_START_DMA) {
+			/*
+			 * In low latency capture, the driver allows application
+			 * to start dma when queue has buffers. That's why we
+			 * don't check for vb2_is_busy().
+			 */
+			if (dma->low_latency_cap &&
+			    vb2_is_streaming(&dma->queue))
+				dma_async_issue_pending(dma->dma);
+			else
+				ret = -EINVAL;
+		} else {
+			ret = -EINVAL;
+		}
+
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static int xvip_dma_open(struct file *file)
+{
+	int ret;
+
+	ret = v4l2_fh_open(file);
+	if (ret)
+		return ret;
+
+	/* Disable the low latency mode as default */
+	if (v4l2_fh_is_singular_file(file)) {
+		struct xvip_dma *dma = video_drvdata(file);
+
+		mutex_lock(&dma->lock);
+		dma->low_latency_cap = false;
+		xilinx_xdma_set_mode(dma->dma, AUTO_RESTART);
+		mutex_unlock(&dma->lock);
+	}
+
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops xvip_dma_ctrl_ops = {
+	.s_ctrl = xvip_dma_s_ctrl,
+};
+
+static const struct v4l2_ctrl_config xvip_dma_ctrls[] = {
+	{
+		.ops = &xvip_dma_ctrl_ops,
+		.id = V4L2_CID_XILINX_LOW_LATENCY,
+		.name = "Low Latency Controls",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = XVIP_LOW_LATENCY_ENABLE,
+		.max = XVIP_START_DMA,
+		.step = 1,
+		.def = XVIP_LOW_LATENCY_DISABLE,
+	}
 };
 
 /* -----------------------------------------------------------------------------
@@ -634,7 +1237,7 @@
 static const struct v4l2_file_operations xvip_dma_fops = {
 	.owner		= THIS_MODULE,
 	.unlocked_ioctl	= video_ioctl2,
-	.open		= v4l2_fh_open,
+	.open		= xvip_dma_open,
 	.release	= vb2_fop_release,
 	.poll		= vb2_fop_poll,
 	.mmap		= vb2_fop_mmap,
@@ -649,6 +1252,7 @@
 {
 	char name[16];
 	int ret;
+	u32 i, hsub, vsub, width, height;
 
 	dma->xdev = xdev;
 	dma->port = port;
@@ -657,42 +1261,132 @@
 	INIT_LIST_HEAD(&dma->queued_bufs);
 	spin_lock_init(&dma->queued_lock);
 
-	dma->fmtinfo = xvip_get_format_by_fourcc(V4L2_PIX_FMT_YUYV);
-	dma->format.pixelformat = dma->fmtinfo->fourcc;
-	dma->format.colorspace = V4L2_COLORSPACE_SRGB;
-	dma->format.field = V4L2_FIELD_NONE;
-	dma->format.width = XVIP_DMA_DEF_WIDTH;
-	dma->format.height = XVIP_DMA_DEF_HEIGHT;
-	dma->format.bytesperline = dma->format.width * dma->fmtinfo->bpp;
-	dma->format.sizeimage = dma->format.bytesperline * dma->format.height;
+	dma->fmtinfo = xvip_get_format_by_fourcc(XVIP_DMA_DEF_FORMAT);
+	dma->format.type = type;
+
+	if (V4L2_TYPE_IS_MULTIPLANAR(type)) {
+		struct v4l2_pix_format_mplane *pix_mp;
+
+		pix_mp = &dma->format.fmt.pix_mp;
+		pix_mp->pixelformat = dma->fmtinfo->fourcc;
+		pix_mp->colorspace = V4L2_COLORSPACE_SRGB;
+		pix_mp->field = V4L2_FIELD_NONE;
+		pix_mp->width = XVIP_DMA_DEF_WIDTH;
+
+		/* Handling contiguous data with mplanes */
+		if (dma->fmtinfo->buffers == 1) {
+			pix_mp->plane_fmt[0].bytesperline =
+				pix_mp->width * dma->fmtinfo->bpl_factor;
+			pix_mp->plane_fmt[0].sizeimage =
+					pix_mp->width * pix_mp->height *
+					dma->fmtinfo->bpp / 8;
+		} else {
+		    /* Handling non-contiguous data with mplanes */
+			hsub = dma->fmtinfo->hsub;
+			vsub = dma->fmtinfo->vsub;
+			for (i = 0; i < dma->fmtinfo->buffers; i++) {
+				width = pix_mp->width / (i ? hsub : 1);
+				height = pix_mp->height / (i ? vsub : 1);
+				pix_mp->plane_fmt[i].bytesperline =
+					width *	dma->fmtinfo->bpl_factor;
+				pix_mp->plane_fmt[i].sizeimage = width * height;
+			}
+		}
+	} else {
+		struct v4l2_pix_format *pix;
+
+		pix = &dma->format.fmt.pix;
+		pix->pixelformat = dma->fmtinfo->fourcc;
+		pix->colorspace = V4L2_COLORSPACE_SRGB;
+		pix->field = V4L2_FIELD_NONE;
+		pix->width = XVIP_DMA_DEF_WIDTH;
+		pix->height = XVIP_DMA_DEF_HEIGHT;
+		pix->bytesperline = pix->width * dma->fmtinfo->bpl_factor;
+		pix->sizeimage =
+			pix->width * pix->height * dma->fmtinfo->bpp / 8;
+	}
 
 	/* Initialize the media entity... */
-	dma->pad.flags = type == V4L2_BUF_TYPE_VIDEO_CAPTURE
-		       ? MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+	if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE ||
+	    type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		dma->pad.flags = MEDIA_PAD_FL_SINK;
+	else
+		dma->pad.flags = MEDIA_PAD_FL_SOURCE;
 
 	ret = media_entity_pads_init(&dma->video.entity, 1, &dma->pad);
 	if (ret < 0)
 		goto error;
 
+	ret = v4l2_ctrl_handler_init(&dma->ctrl_handler,
+				     ARRAY_SIZE(xvip_dma_ctrls));
+	if (ret < 0) {
+		dev_err(dma->xdev->dev, "failed to initialize V4L2 ctrl\n");
+		goto error;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(xvip_dma_ctrls); i++) {
+		struct v4l2_ctrl *ctrl;
+
+		dev_dbg(dma->xdev->dev, "%d ctrl = 0x%x\n", i,
+			xvip_dma_ctrls[i].id);
+		ctrl = v4l2_ctrl_new_custom(&dma->ctrl_handler,
+					    &xvip_dma_ctrls[i], NULL);
+		if (!ctrl) {
+			dev_err(dma->xdev->dev, "Failed for %s ctrl\n",
+				xvip_dma_ctrls[i].name);
+			goto error;
+		}
+	}
+
+	if (dma->ctrl_handler.error) {
+		dev_err(dma->xdev->dev, "failed to add controls\n");
+		ret = dma->ctrl_handler.error;
+		goto error;
+	}
+
+	ret = v4l2_ctrl_handler_setup(&dma->ctrl_handler);
+	if (ret < 0) {
+		dev_err(dma->xdev->dev, "failed to set controls\n");
+		goto error;
+	}
+
 	/* ... and the video node... */
 	dma->video.fops = &xvip_dma_fops;
 	dma->video.v4l2_dev = &xdev->v4l2_dev;
+	dma->video.v4l2_dev->ctrl_handler = &dma->ctrl_handler;
 	dma->video.queue = &dma->queue;
 	snprintf(dma->video.name, sizeof(dma->video.name), "%pOFn %s %u",
 		 xdev->dev->of_node,
-		 type == V4L2_BUF_TYPE_VIDEO_CAPTURE ? "output" : "input",
+		 (type == V4L2_BUF_TYPE_VIDEO_CAPTURE ||
+		  type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+					? "output" : "input",
 		 port);
+
 	dma->video.vfl_type = VFL_TYPE_VIDEO;
-	dma->video.vfl_dir = type == V4L2_BUF_TYPE_VIDEO_CAPTURE
-			   ? VFL_DIR_RX : VFL_DIR_TX;
+	if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE ||
+	    type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		dma->video.vfl_dir = VFL_DIR_RX;
+	else
+		dma->video.vfl_dir = VFL_DIR_TX;
+
 	dma->video.release = video_device_release_empty;
 	dma->video.ioctl_ops = &xvip_dma_ioctl_ops;
 	dma->video.lock = &dma->lock;
 	dma->video.device_caps = V4L2_CAP_STREAMING;
-	if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
+	switch (dma->format.type) {
+	case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE:
+		dma->video.device_caps |= V4L2_CAP_VIDEO_CAPTURE_MPLANE;
+		break;
+	case V4L2_BUF_TYPE_VIDEO_CAPTURE:
 		dma->video.device_caps |= V4L2_CAP_VIDEO_CAPTURE;
-	else
+		break;
+	case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE:
+		dma->video.device_caps |= V4L2_CAP_VIDEO_OUTPUT_MPLANE;
+		break;
+	case V4L2_BUF_TYPE_VIDEO_OUTPUT:
 		dma->video.device_caps |= V4L2_CAP_VIDEO_OUTPUT;
+		break;
+	}
 
 	video_set_drvdata(&dma->video, dma);
 
@@ -730,6 +1424,13 @@
 		goto error;
 	}
 
+	xilinx_xdma_get_width_align(dma->dma, &dma->width_align);
+	if (!dma->width_align) {
+		dev_dbg(dma->xdev->dev,
+			"Using width align %d\n", XVIP_DMA_DEF_WIDTH_ALIGN);
+		dma->width_align = XVIP_DMA_DEF_WIDTH_ALIGN;
+	}
+
 	dma->align = 1 << dma->dma->device->copy_align;
 
 	ret = video_register_device(&dma->video, VFL_TYPE_VIDEO, -1);
@@ -753,6 +1454,7 @@
 	if (!IS_ERR_OR_NULL(dma->dma))
 		dma_release_channel(dma->dma);
 
+	v4l2_ctrl_handler_free(&dma->ctrl_handler);
 	media_entity_cleanup(&dma->video.entity);
 
 	mutex_destroy(&dma->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-dma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-dma.h
@@ -18,6 +18,7 @@
 #include <linux/videodev2.h>
 
 #include <media/media-entity.h>
+#include <media/v4l2-ctrls.h>
 #include <media/v4l2-dev.h>
 #include <media/videobuf2-v4l2.h>
 
@@ -32,7 +33,7 @@
  * @use_count: number of DMA engines using the pipeline
  * @stream_count: number of DMA engines currently streaming
  * @num_dmas: number of DMA engines in the pipeline
- * @output: DMA engine at the output of the pipeline
+ * @xdev: Composite device the pipe belongs to
  */
 struct xvip_pipeline {
 	struct media_pipeline pipe;
@@ -42,7 +43,7 @@
 	unsigned int stream_count;
 
 	unsigned int num_dmas;
-	struct xvip_dma *output;
+	struct xvip_composite_device *xdev;
 };
 
 static inline struct xvip_pipeline *to_xvip_pipeline(struct media_entity *e)
@@ -55,33 +56,47 @@
  * @list: list entry in a composite device dmas list
  * @video: V4L2 video device associated with the DMA channel
  * @pad: media pad for the video device entity
+ * @remote_subdev_med_bus: media bus format of sub-device
+ * @ctrl_handler: V4L2 ctrl_handler for inheritance ctrls from subdev
  * @xdev: composite device the DMA channel belongs to
  * @pipe: pipeline belonging to the DMA channel
  * @port: composite device DT node port number for the DMA channel
  * @lock: protects the @format, @fmtinfo and @queue fields
  * @format: active V4L2 pixel format
+ * @r: crop rectangle parameters
  * @fmtinfo: format information corresponding to the active @format
+ * @poss_v4l2_fmts: All possible v4l formats supported
+ * @poss_v4l2_fmt_cnt: number of supported v4l formats
  * @queue: vb2 buffers queue
  * @sequence: V4L2 buffers sequence number
  * @queued_bufs: list of queued buffers
  * @queued_lock: protects the buf_queued list
  * @dma: DMA engine channel
  * @align: transfer alignment required by the DMA channel (in bytes)
+ * @width_align: width alignment required by the DMA channel (in bytes)
  * @xt: dma interleaved template for dma configuration
  * @sgl: data chunk structure for dma_interleaved_template
+ * @prev_fid: Previous Field ID
+ * @low_latency_cap: Low latency capture mode
  */
 struct xvip_dma {
 	struct list_head list;
 	struct video_device video;
 	struct media_pad pad;
+	u32 remote_subdev_med_bus;
+
+	struct v4l2_ctrl_handler ctrl_handler;
 
 	struct xvip_composite_device *xdev;
 	struct xvip_pipeline pipe;
 	unsigned int port;
 
 	struct mutex lock;
-	struct v4l2_pix_format format;
+	struct v4l2_format format;
+	struct v4l2_rect r;
 	const struct xvip_video_format *fmtinfo;
+	u32 *poss_v4l2_fmts;
+	u32 poss_v4l2_fmt_cnt;
 
 	struct vb2_queue queue;
 	unsigned int sequence;
@@ -91,8 +106,12 @@
 
 	struct dma_chan *dma;
 	unsigned int align;
+	unsigned int width_align;
 	struct dma_interleaved_template xt;
 	struct data_chunk sgl[1];
+
+	u32 prev_fid;
+	u32 low_latency_cap;
 };
 
 #define to_xvip_dma(vdev)	container_of(vdev, struct xvip_dma, video)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-dprxss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-dprxss.c
@@ -0,0 +1,2077 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DP Rx Subsystem
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ *
+ * Author: Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>
+ *
+ */
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-dp.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/v4l2-dv-timings.h>
+#include <linux/v4l2-subdev.h>
+
+#include <drm/drm_dp_helper.h>
+#include <dt-bindings/media/xilinx-vip.h>
+
+#include <media/v4l2-dv-timings.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-subdev.h>
+
+#include <sound/soc.h>
+
+#include "xilinx-vip.h"
+
+#define XV_AES_ENABLE			0x8
+#define XDP_AUDIO_DETECT_TIMEOUT	500 /* milliseconds */
+#define INFO_PCKT_SIZE_WORDS		8
+#define INFO_PCKT_SIZE			(INFO_PCKT_SIZE_WORDS * 4)
+#define INFO_PCKT_TYPE_AUDIO		0x84
+
+/* DP Rx subsysetm register map, bitmask, and offsets. */
+#define XDPRX_LINK_ENABLE_REG		0x000
+#define XDPRX_AUX_CLKDIV_REG		0x004
+#define XDPRX_AUX_DEFER_COUNT		6
+#define XDPRX_AUX_DEFER_SHIFT		24
+#define XDPRX_AUX_DEFER_MASK		GENMASK(27, 24)
+
+#define XDPRX_LINERST_DIS_REG		0x008
+#define XDPRX_DTG_REG			0x00c
+#define XDPRX_DTG_DIS_MASK		GENMASK(31, 1)
+
+#define XDPRX_PIXEL_WIDTH_REG		0x010
+#define XDPRX_INTR_MASK_REG		0x014
+#define XDPRX_INTR_POWER_MASK		BIT(1)
+#define XDPRX_INTR_NOVID_MASK		BIT(2)
+#define XDPRX_INTR_VBLANK_MASK		BIT(3)
+#define XDPRX_INTR_TRLOST_MASK		BIT(4)
+#define XDPRX_INTR_VID_MASK		BIT(6)
+#define XDPRX_INTR_AUDIO_MASK		BIT(8)
+#define XDPRX_INTR_TRDONE_MASK		BIT(14)
+#define XDPRX_INTR_BWCHANGE_MASK	BIT(15)
+#define XDPRX_INTR_TP1_MASK		BIT(16)
+#define XDPRX_INTR_TP2_MASK		BIT(17)
+#define XDPRX_INTR_TP3_MASK		BIT(18)
+#define XDPRX_INTR_LINKQUAL_MASK	BIT(29)
+#define XDPRX_INTR_UNPLUG_MASK		BIT(31)
+#define XDPRX_INTR_CRCTST_MASK		BIT(30)
+#define XDPRX_INTR_TRNG_MASK		(XDPRX_INTR_TP1_MASK | \
+					 XDPRX_INTR_TP2_MASK |\
+					 XDPRX_INTR_TP3_MASK | \
+					 XDPRX_INTR_POWER_MASK |\
+					 XDPRX_INTR_CRCTST_MASK |\
+					 XDPRX_INTR_BWCHANGE_MASK)
+#define XDPRX_INTR_ACCESS_LANE_SET_MASK		BIT(30)
+#define XDPRX_INTR_TP4_MASK			BIT(31)
+#define XDPRX_INTR_ACCESS_LINK_QUAL_MASK	BIT(29)
+#define XDPRX_INTR_ACCESS_ERR_CNT_MASK		BIT(28)
+#define XDPRX_INTR_TRNG_MASK_1		(XDPRX_INTR_TP4_MASK | \
+					 XDPRX_INTR_ACCESS_LANE_SET_MASK | \
+					 XDPRX_INTR_ACCESS_LINK_QUAL_MASK | \
+					 XDPRX_INTR_ACCESS_ERR_CNT_MASK)
+#define XDPRX_INTR_ALL_MASK		0xffffffff
+#define XDPRX_INTR_ALL_MASK_1		0xffffffff
+
+#define XDPRX_SOFT_RST_REG		0x01c
+#define XDPRX_SOFT_VIDRST_MASK		BIT(0)
+#define XDPRX_SOFT_AUXRST_MASK		BIT(7)
+
+#define XDPRX_HPD_INTR_REG		0x02c
+#define XDPRX_HPD_INTR_MASK		BIT(1)
+#define XDPRX_HPD_PULSE_MASK		GENMASK(31, 16)
+
+#define XDPRX_INTR_CAUSE_REG		0x040
+#define XDPRX_INTR_MASK_1_REG		0x044
+#define XDPRX_INTR_CAUSE_1_REG		0x048
+#define XDPRX_CRC_CONFIG_REG		0x074
+#define XDPRX_CRC_EN_MASK		BIT(5)
+
+#define XDPRX_LOCAL_EDID_REG		0x084
+#define XDPRX_VIDEO_UNSUPPORTED_REG	0x094
+#define XDPRX_VRD_BWSET_REG		0x09c
+#define XDPRX_LANE_CNT_REG		0x0a0
+#define XDPRX_EFRAME_CAP_MASK		BIT(7)
+#define XDPRX_LNCNT_TPS3_MASK		BIT(6)
+
+#define XDPRX_TP_SET_REG		0x0a4
+#define XDPRX_AUX_RDINT_SHIFT		8
+#define XDPRX_AUX_RDINT_16MS		4
+#define XDPRX_AUX_READINTRVL_REG	BIT(15)
+
+#define XDPRX_CTRL_DPCD_REG		0x0b8
+#define XDPRX_MST_CAP_REG		0x0d0
+#define XDPRX_SINK_COUNT_REG		0x0d4
+
+#define XDPRX_PHY_REG			0x200
+#define XDPRX_PHY_GTPLLRST_MASK		BIT(0)
+#define XDPRX_PHY_GTRXRST_MASK		BIT(1)
+#define XDPRX_PHYRST_TRITER_MASK	BIT(23)
+#define XDPRX_PHYRST_RATECHANGE_MASK	BIT(24)
+#define XDPRX_PHYRST_TP1START_MASK	BIT(25)
+#define XDPRX_PHYRST_ENBL_MASK		0x0
+#define XDPRX_PHY_INIT_MASK		GENMASK(29, 27)
+
+#define XDPRX_PHYSTATUS_REG			0x208
+#define XDPRX_PHYSTATUS_ALL_LANES_GOOD_MASK	GENMASK(6, 0)
+#define XDPRX_PHYSTATUS_READ_COUNT	100
+
+#define XDPRX_MINVOLT_SWING_REG		0x214
+#define XDPRX_VS_PE_SHIFT		12
+#define XDPRX_VS_SWEEP_CNTSHIFT		4
+#define XDPRX_VS_CROPT_SHIFT		2
+#define XDPRX_VS_CROPT_INC4CNT		1
+#define XDPRX_MIN_VS_MASK		(1 | (XDPRX_VS_CROPT_INC4CNT << \
+					 XDPRX_VS_CROPT_SHIFT) | \
+					 (4 << XDPRX_VS_SWEEP_CNTSHIFT) | \
+					 (1 << XDPRX_VS_PE_SHIFT))
+
+#define XDPRX_CDRCTRL_CFG_REG		0x21c
+/* default CDR tDLOCK calibration value */
+#define XDPRX_CDRCTRL_TDLOCK_VAL	0x1388
+#define XDPRX_CDRCTRL_TDLOCK_MASK	GENMASK(19, 0)
+#define XDPRX_CDRCTRL_DIS_TIMEOUT	BIT(30)
+
+#define XDPRX_BSIDLE_TIME_REG		0x220
+#define XDPRX_BSIDLE_TMOUT_VAL		0x047868C0
+
+#define XDPRX_AUDIO_CONTROL		0x300
+#define XDPRX_AUDIO_EN_MASK		BIT(0)
+#define XDPRX_AUDIO_INFO_DATA		0x304
+#define XDPRX_AUDIO_MAUD		0x324
+#define XDPRX_AUDIO_NAUD		0x328
+#define XDPRX_AUDIO_STATUS		0x32C
+
+#define XDPRX_LINK_BW_REG		0x400
+#define XDPRX_LANE_COUNT_REG		0x404
+#define XDPRX_DPCD_TRAINING_PATTERN_SET	0x40c
+#define XDPRX_DPCD_LANE01_STATUS	0x43c
+#define XDPRX_LANE01_PEVS_MASK		GENMASK(15, 8)
+#define XDPRX_DPC_LINK_QUAL_CONFIG	0x454
+#define XDPRX_DPCD_LINK_QUAL_PRBS_MASK	GENMASK(1, 0)
+#define XDPRX_LINK_QUAL_PRBS_MODE_MASK	GENMASK(2, 0)
+#define XDPRX_MSA_HRES_REG		0x500
+#define XDPRX_MSA_HSPOL_REG		0x504
+#define XDPRX_MSA_HSPOL_MASK		BIT(0)
+#define XDPRX_MSA_HSWIDTH_REG		0x508
+#define XDPRX_MSA_HSTART_REG		0x50c
+#define XDPRX_MSA_VHEIGHT_REG		0x514
+#define XDPRX_MSA_HTOTAL_REG		0x510
+#define XDPRX_MSA_VSPOL_REG		0x518
+#define XDPRX_MSA_VSPOL_MASK		BIT(0)
+#define XDPRX_MSA_VSWIDTH_REG		0x51c
+#define XDPRX_MSA_VSTART_REG		0x520
+#define XDPRX_MSA_VTOTAL_REG		0x524
+#define XDPRX_MSA_MISC0_REG		0x528
+#define XDPRX_MSA_FMT_MASK		GENMASK(2, 1)
+#define XDPRX_MSA_BPC_MASK		GENMASK(7, 5)
+#define XDPRX_COLOR_DEPTH_SHIFT		5
+#define XDPRX_COLOR_FMT_SHIFT		1
+
+#define XDPRX_MSA_MISC1_REG		0x52c
+#define XDPRX_INTERLACE_MASK		BIT(0)
+
+#define XDPRX_MSA_MVID_REG		0x530
+#define XDPRX_MSA_NVID_REG		0x534
+#define XDPRX_INTR_ERRORCNT_MASK	BIT(28)
+#define XDPRX_INTR_LANESET_MASK		BIT(30)
+
+#define XDPRX_EXT_VRD_BWSET_REG		0x7f0
+
+#define XDPRX_COLOR_FORMAT_RGB		0x0
+#define XDPRX_COLOR_FORMAT_422		0x1
+#define XDPRX_COLOR_FORMAT_444		0x2
+#define MHZ				1000000
+#define XDPRX_MAX_LANE_COUNT		4
+
+#define XDPRX_EDID_NUM_BLOCKS		3
+#define XDPRX_EDID_BLOCK_SIZE		128
+#define XDPRX_EDID_LENGTH		(XDPRX_EDID_BLOCK_SIZE * \
+					 XDPRX_EDID_NUM_BLOCKS * 4)
+/*
+ * IRQ_HPD pulse for upstream device is 5ms as per
+ * the VESA standard
+ */
+#define XDPRX_HPD_PULSE_5000		5000
+/*
+ * low going IRQ_HPD generated for upstream device
+ * as per the VESA standard
+ */
+#define XDPRX_HPD_PULSE_750		750
+
+/* GtCtrl Registers */
+#define XDPRX_GTCTL_REG			0x4C
+#define XDPRX_GTCTL_EN			BIT(0)
+#define XDPRX_GTCTL_VSWING_MASK		GENMASK(12, 8)
+#define XDPRX_GTCTL_VSWING_INIT_VAL	0x05
+#define XDPRX_GTCTL_LINE_RATE_MASK	GENMASK(2, 1)
+#define XDPRX_GTCTL_LINE_RATE_810G	3
+#define XDPRX_GTCTL_LINE_RATE_540G	2
+#define XDPRX_GTCTL_LINE_RATE_270G	1
+#define XDPRX_GTCTL_LINE_RATE_162G	0
+
+#define DP_LINK_BW_1_62G	1620
+#define DP_LINK_BW_2_7G		2700
+#define DP_LINK_BW_5_4G		5400    /* 1.2 */
+#define DP_LINK_BW_8_1G		8100    /* 1.4 */
+
+#define XDPRXSS_MMCM_OFFSET		0x5000
+
+/* Clock Wizard registers */
+#define XDPRX_MMCM_SWRST_OFFSET		0x00000000
+#define XDPRX_MMCM_SWRST_VAL		0xA
+#define XDPRX_MMCM_STATUS_OFFSET	0x00000004
+#define XDPRX_MMCM_ISR_OFFSET		0x0000000C
+#define XDPRX_MMCM_IER_OFFSET		0x00000010
+#define XDPRX_MMCM_RECONFIG_OFFSET	0x00000014
+#define XDPRX_MMCM_REG1_OFFSET		0x00000330
+#define XDPRX_MMCM_REG2_OFFSET		0x00000334
+#define XDPRX_MMCM_REG3_OFFSET		0x00000338
+#define XDPRX_MMCM_REG4_OFFSET		0x0000033C
+#define XDPRX_MMCM_REG12_OFFSET		0x00000380
+#define XDPRX_MMCM_REG13_OFFSET		0x00000384
+#define XDPRX_MMCM_REG11_OFFSET		0x00000378
+#define XDPRX_MMCM_REG11_VAL		0x2e
+#define XDPRX_MMCM_REG14_OFFSET		0x00000398
+#define XDPRX_MMCM_REG14_VAL		0xe80
+#define XDPRX_MMCM_REG15_OFFSET		0x0000039C
+#define XDPRX_MMCM_REG15_VAL		0x4271
+#define XDPRX_MMCM_REG16_OFFSET		0x000003A0
+#define XDPRX_MMCM_REG16_VAL		0x43e9
+#define XDPRX_MMCM_REG17_OFFSET		0x000003A8
+#define XDPRX_MMCM_REG17_VAL		0x1c
+#define XDPRX_MMCM_REG19_OFFSET		0x000003CC
+#define XDPRX_MMCM_REG25_OFFSET		0x000003F0
+#define XDPRX_MMCM_REG26_OFFSET		0x000003FC
+#define XDPRX_MMCM_REG26_VAL		1
+
+#define XDPRX_MMCM_LOCK			BIT(0)
+#define XDPRX_MMCM_REG3_PREDIV2		BIT(11)
+#define XDPRX_MMCM_REG3_USED		BIT(12)
+#define XDPRX_MMCM_REG3_MX		BIT(9)
+#define XDPRX_MMCM_REG1_PREDIV2		BIT(12)
+#define XDPRX_MMCM_REG1_EN		BIT(9)
+#define XDPRX_MMCM_REG1_MX		BIT(10)
+#define XDPRX_MMCM_RECONFIG_LOAD	BIT(0)
+#define XDPRX_MMCM_RECONFIG_SADDR	BIT(1)
+#define XDPRX_MMCM_REG1_EDGE_MASK	BIT(8)
+
+#define XDPRX_MMCM_CLKOUT0_PREDIV2_SHIFT	11
+#define XDPRX_MMCM_CLKOUT0_MX_SHIFT		9
+#define XDPRX_MMCM_CLKOUT0_P5EN_SHIFT		13
+#define XDPRX_MMCM_CLKOUT0_P5FEDGE_SHIFT	15
+#define XDPRX_MMCM_REG12_EDGE_SHIFT		10
+
+#define XDPRX_MMCM_M_VAL_405		28
+#define XDPRX_MMCM_M_VAL_270		44
+#define XDPRX_MMCM_M_VAL_135		88
+#define XDPRX_MMCM_M_VAL_81		148
+#define XDPRX_MMCM_D_VAL		5
+#define XDPRX_MMCM_M_O_VAL_RATIO	4
+#define XDPRX_MMCM_STATUS_RETRY		10000
+
+#define MMCM_O_VAL_FEDGE_DIVIDER	2
+#define MMCM_O_VAL_HIGHTIME_DIVIDER	4
+#define MMCM_O_VAL_EDGE_DIVIDER		4
+#define MMCM_D_VAL_EDGE_DIVIDER		2
+#define MMCM_D_VAL_HIGHTIME_DIVIDER	2
+#define MMCM_M_VAL_EDGE_DIVIDER		2
+#define MMCM_M_VAL_HIGHTIME_DIVIDER	2
+#define MMCM_MDO_VAL_HIGHTIME_SHIFT	8
+
+#define xdprxss_generate_hpd_intr(state, duration) \
+		xdprxss_write(state, XDPRX_HPD_INTR_REG, \
+			      FIELD_PREP(XDPRX_HPD_PULSE_MASK, duration) |\
+			      XDPRX_HPD_INTR_MASK)
+#define xdprxss_disable_unplug_intr(state) \
+		xdprxss_set(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_UNPLUG_MASK)
+#define xdprxss_disable_audio(state) \
+		xdprxss_clr(state, XDPRX_AUDIO_CONTROL, XDPRX_AUDIO_EN_MASK)
+#define xdprxss_dtg_enable(state)	xdprxss_set(state, XDPRX_DTG_REG, 1)
+#define xdprxss_update_ext_rcv_cap(xdprxss, max_linkrate) \
+		xdprxss_write(xdprxss, \
+			      XDPRX_EXT_VRD_BWSET_REG, max_linkrate)
+#define xdprxss_set_clk_data_recovery_timeout_val(xdprxss, value) \
+		xdprxss_write(xdprxss, XDPRX_CDRCTRL_CFG_REG, \
+				FIELD_PREP(XDPRX_CDRCTRL_TDLOCK_MASK, value))
+#define xdprxss_enable_training_timeout(xdprxss) \
+		xdprxss_clr(xdprxss, XDPRX_CDRCTRL_CFG_REG, \
+			    XDPRX_CDRCTRL_DIS_TIMEOUT)
+#define xdprxss_enable_training_intr(xdprxss) \
+		xdprxss_clr(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_TRNG_MASK)
+#define xdprxss_enable_training_intr_1(state) \
+		xdprxss_clr(state, XDPRX_INTR_MASK_1_REG, XDPRX_INTR_TRNG_MASK_1)
+#define xdprxss_disable_allintr(state) \
+		xdprxss_set(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_ALL_MASK)
+#define xdprxss_disable_allintr_1(state) \
+		xdprxss_set(state, XDPRX_INTR_MASK_1_REG, XDPRX_INTR_ALL_MASK_1)
+#define xdprxss_enable_audio_intr(state) \
+		xdprxss_clr(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_AUDIO_MASK)
+
+/**
+ * struct xlnx_dprx_audio_data - DP Rx Subsystem audio data structure
+ * @infoframe: Audio infoframe that is received
+ * @audio_detected: To indicate audio detection
+ * @audio_update_q: wait queue for audio detection
+ */
+struct xlnx_dprx_audio_data {
+	u32 infoframe[8];
+	bool audio_detected;
+	wait_queue_head_t audio_update_q;
+};
+
+/**
+ * struct retimer_cfg - Retimer configuration structure
+ * @retimer_access_laneset: Function pointer to retimer access laneset function
+ * @retimer_rst_cr_path: Function pointer to retimer reset cr path function
+ * @retimer_rst_dp_path: Function pointer to retimer reset dp path function
+ * @retimer_prbs_mode: Function pointer to prbs mode enable/disable function
+ */
+struct retimer_cfg {
+	void (*retimer_access_laneset)(void);
+	void (*retimer_rst_cr_path)(void);
+	void (*retimer_rst_dp_path)(void);
+	void (*retimer_prbs_mode)(u8 enable);
+};
+
+/**
+ * struct vidphy_cfg - Video phy configuration structure
+ * @vidphy_prbs_mode: Function pointer to prbs mode enable/disable function
+ */
+struct vidphy_cfg {
+	void (*vidphy_prbs_mode)(u8 enable);
+};
+
+/**
+ * struct xdprxss_state - DP Rx Subsystem device structure
+ * @dev: Platform structure
+ * @subdev: The v4l2 subdev structure
+ * @event: Holds the video unlock event
+ * @detected_timings: Detected Video timings
+ * @phy: pointer to phy instance
+ * @pad: media pad
+ * @axi_clk: Axi lite interface clock
+ * @rx_lnk_clk: DP Rx GT clock
+ * @rx_vid_clk: DP RX Video clock
+ * @rx_dec_clk: DP Rx Decode clock
+ * @dp_base: Base address of DP Rx Subsystem
+ * @edid_base: Bare Address of EDID block
+ * @prvdata: Pointer to device private data
+ * @retimer_prvdata: Pointer to retimer private data structure
+ * @vidphy_prvdata: Pointer to video phy private data structure
+ * @tp1_work: training pattern 1 worker
+ * @unplug_work: Unplug worker
+ * @lock: Lock is used for width, height, framerate variables
+ * @format: Active V4L2 format on each pad
+ * @frame_interval: Captures the frame rate
+ * @max_linkrate: Maximum supported link rate
+ * @max_lanecount: Maximux supported lane count
+ * @bpc: Bits per component
+ * @ce_req_val: Variable for storing channel status
+ * @versal_gt_present: flag to indicate versal-gt property in device tree
+ * @hdcp_enable: To indicate hdcp enabled or not
+ * @audio_enable: To indicate audio enabled or not
+ * @audio_init: flag to indicate audio is initialized
+ * @rx_audio_data: audio data
+ * @valid_stream: To indicate valid video
+ * @streaming: Flag for storing streaming state
+ * @ltstate: Flag for storing link training state
+ * This structure contains the device driver related parameters
+ */
+struct xdprxss_state {
+	struct device *dev;
+	struct v4l2_subdev subdev;
+	struct v4l2_event event;
+	struct v4l2_dv_timings detected_timings;
+	struct phy *phy[XDPRX_MAX_LANE_COUNT];
+	struct media_pad pad;
+	struct clk *axi_clk;
+	struct clk *rx_lnk_clk;
+	struct clk *rx_vid_clk;
+	void __iomem *dp_base;
+	void __iomem *edid_base;
+	void *prvdata;
+	struct retimer_cfg *retimer_prvdata;
+	struct vidphy_cfg *vidphy_prvdata;
+	struct delayed_work tp1_work;
+	struct delayed_work unplug_work;
+	/* protects width, height, framerate variables */
+	spinlock_t lock;
+	struct v4l2_mbus_framefmt format;
+	unsigned int frame_interval;
+	u32 max_linkrate;
+	u32 max_lanecount;
+	u32 bpc;
+	u32 ce_req_val;
+	bool versal_gt_present;
+	bool hdcp_enable;
+	bool audio_enable;
+	bool audio_init;
+	struct xlnx_dprx_audio_data *rx_audio_data;
+	unsigned int valid_stream : 1;
+	unsigned int streaming : 1;
+	unsigned int ltstate : 2;
+};
+
+/*
+ * This is a default EDID data loaded to EDID memory. It allows the source
+ * to get edid before application start on DP Rx.User can load their
+ * custom EDID data using set_edid functions call
+ */
+static u8 xilinx_edid[384] = {
+	0x00, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x00, 0x10, 0xac, 0x47, 0x41,
+	0x4c, 0x35, 0x37, 0x30, 0x20, 0x1b, 0x01, 0x04, 0xb5, 0x46, 0x27, 0x78,
+	0x3a, 0x76, 0x45, 0xae, 0x51, 0x33, 0xba, 0x26, 0x0d, 0x50, 0x54, 0xa5,
+	0x4b, 0x00, 0x81, 0x00, 0xb3, 0x00, 0xd1, 0x00, 0xa9, 0x40, 0x81, 0x80,
+	0xd1, 0xc0, 0x01, 0x01, 0x01, 0x01, 0x4d, 0xd0, 0x00, 0xa0, 0xf0, 0x70,
+	0x3e, 0x80, 0x30, 0x20, 0x35, 0x00, 0xba, 0x89, 0x21, 0x00, 0x00, 0x1a,
+	0x00, 0x00, 0x00, 0xff, 0x00, 0x46, 0x46, 0x4e, 0x58, 0x4d, 0x37, 0x38,
+	0x37, 0x30, 0x37, 0x35, 0x4c, 0x0a, 0x00, 0x00, 0x00, 0xfc, 0x00, 0x44,
+	0x45, 0x4c, 0x4c, 0x20, 0x55, 0x50, 0x33, 0x32, 0x31, 0x38, 0x4b, 0x0a,
+	0x00, 0x00, 0x00, 0xfd, 0x00, 0x18, 0x4b, 0x1e, 0xb4, 0x6c, 0x01, 0x0a,
+	0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x02, 0x70, 0x02, 0x03, 0x1d, 0xf1,
+	0x50, 0x10, 0x1f, 0x20, 0x05, 0x14, 0x04, 0x13, 0x12, 0x11, 0x03, 0x02,
+	0x16, 0x15, 0x07, 0x06, 0x01, 0x23, 0x09, 0x1f, 0x07, 0x83, 0x01, 0x00,
+	0x00, 0xa3, 0x66, 0x00, 0xa0, 0xf0, 0x70, 0x1f, 0x80, 0x30, 0x20, 0x35,
+	0x00, 0xba, 0x89, 0x21, 0x00, 0x00, 0x1a, 0x56, 0x5e, 0x00, 0xa0, 0xa0,
+	0xa0, 0x29, 0x50, 0x30, 0x20, 0x35, 0x00, 0xba, 0x89, 0x21, 0x00, 0x00,
+	0x1a, 0x7c, 0x39, 0x00, 0xA0, 0x80, 0x38, 0x1f, 0x40, 0x30, 0x20, 0x3a,
+	0x00, 0xba, 0x89, 0x21, 0x00, 0x00, 0x1a, 0xa8, 0x16, 0x00, 0xa0, 0x80,
+	0x38, 0x13, 0x40, 0x30, 0x20, 0x3a, 0x00, 0xba, 0x89, 0x21, 0x00, 0x00,
+	0x1a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x47, 0x70, 0x12, 0x79, 0x00, 0x00, 0x12, 0x00, 0x16,
+	0x82, 0x10, 0x10, 0x00, 0xff, 0x0e, 0xdf, 0x10, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x44, 0x45, 0x4c, 0x47, 0x41, 0x4c, 0x35, 0x37, 0x30, 0x03, 0x01,
+	0x50, 0x70, 0x92, 0x01, 0x84, 0xff, 0x1d, 0xc7, 0x00, 0x1d, 0x80, 0x09,
+	0x00, 0xdf, 0x10, 0x2f, 0x00, 0x02, 0x00, 0x04, 0x00, 0xc1, 0x42, 0x01,
+	0x84, 0xff, 0x1d, 0xc7, 0x00, 0x2f, 0x80, 0x1f, 0x00, 0xdf, 0x10, 0x30,
+	0x00, 0x02, 0x00, 0x04, 0x00, 0xa8, 0x4e, 0x01, 0x04, 0xff, 0x0e, 0xc7,
+	0x00, 0x2f, 0x80, 0x1f, 0x00, 0xdf, 0x10, 0x61, 0x00, 0x02, 0x00, 0x09,
+	0x00, 0x97, 0x9d, 0x01, 0x04, 0xff, 0x0e, 0xc7, 0x00, 0x2f, 0x80, 0x1f,
+	0x00, 0xdf, 0x10, 0x2f, 0x00, 0x02, 0x00, 0x09, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x88, 0x90,
+};
+
+static const u32 xdprxss_supported_mbus_fmts[] = {
+	MEDIA_BUS_FMT_UYVY8_1X16,
+	MEDIA_BUS_FMT_VUY8_1X24,
+	MEDIA_BUS_FMT_RBG888_1X24,
+	MEDIA_BUS_FMT_UYVY10_1X20,
+	MEDIA_BUS_FMT_VUY10_1X30,
+	MEDIA_BUS_FMT_RBG101010_1X30,
+};
+
+#define XLNX_V4L2_DV_BT_2048X1080P60 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 88, 44, 20, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_CEA861) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080I50 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 274, 44, 274, 2, 5, 15, 3, 5, 15, \
+		V4L2_DV_BT_STD_CEA861) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080I60 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 66, 20, 66, 2, 5, 15, 3, 5, 15, \
+		V4L2_DV_BT_STD_CEA861) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P50 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_CEA861) \
+}
+
+#define XLNX_V4L2_DV_BT_7680X4320P25 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(7680, 4320, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 2552, 176, 592, 16, 20, 44, 0, 0, 0, \
+		V4L2_DV_BT_STD_CEA861) \
+}
+
+#define XLNX_V4L2_DV_BT_7680X4320P30 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(7680, 4320, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 552, 176, 592, 16, 20, 44, 0, 0, 0, \
+		V4L2_DV_BT_STD_CEA861) \
+}
+
+static const struct v4l2_dv_timings fmt_cap[] = {
+	V4L2_DV_BT_CEA_1280X720P25,
+	V4L2_DV_BT_CEA_1280X720P30,
+	V4L2_DV_BT_CEA_1280X720P50,
+	V4L2_DV_BT_CEA_1280X720P60,
+	V4L2_DV_BT_CEA_1920X1080P25,
+	V4L2_DV_BT_CEA_1920X1080P30,
+	V4L2_DV_BT_CEA_1920X1080P50,
+	V4L2_DV_BT_CEA_1920X1080P60,
+	V4L2_DV_BT_CEA_1920X1080I50,
+	V4L2_DV_BT_CEA_1920X1080I60,
+	V4L2_DV_BT_CEA_3840X2160P30,
+	V4L2_DV_BT_CEA_3840X2160P50,
+	V4L2_DV_BT_CEA_3840X2160P60,
+	V4L2_DV_BT_CEA_4096X2160P25,
+	V4L2_DV_BT_CEA_4096X2160P30,
+	V4L2_DV_BT_CEA_4096X2160P50,
+	V4L2_DV_BT_CEA_4096X2160P60,
+
+	XLNX_V4L2_DV_BT_2048X1080I50,
+	XLNX_V4L2_DV_BT_2048X1080I60,
+	XLNX_V4L2_DV_BT_2048X1080P50,
+	XLNX_V4L2_DV_BT_2048X1080P60,
+	XLNX_V4L2_DV_BT_7680X4320P30,
+};
+
+static inline struct xdprxss_state *
+to_xdprxssstate(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xdprxss_state, subdev);
+}
+
+/* Register related operations */
+static inline u32 xdprxss_mmcm_read(struct xdprxss_state *xdprxss, u32 addr)
+{
+	return ioread32(xdprxss->dp_base + XDPRXSS_MMCM_OFFSET + addr);
+}
+
+static inline void xdprxss_mmcm_write(struct xdprxss_state *xdprxss, u32 addr,
+				      u32 value)
+{
+	iowrite32(value, xdprxss->dp_base + XDPRXSS_MMCM_OFFSET + addr);
+}
+
+static inline u32 xdprxss_read(struct xdprxss_state *xdprxss, u32 addr)
+{
+	return ioread32(xdprxss->dp_base + addr);
+}
+
+static inline void xdprxss_write(struct xdprxss_state *xdprxss, u32 addr,
+				 u32 value)
+{
+	iowrite32(value, xdprxss->dp_base + addr);
+}
+
+static inline void xdprxss_clr(struct xdprxss_state *xdprxss, u32 addr,
+			       u32 clr)
+{
+	xdprxss_write(xdprxss, addr, xdprxss_read(xdprxss, addr) & ~clr);
+}
+
+static inline void xdprxss_set(struct xdprxss_state *xdprxss, u32 addr,
+			       u32 set)
+{
+	xdprxss_write(xdprxss, addr, xdprxss_read(xdprxss, addr) | set);
+}
+
+static void xdprxss_clrset(struct xdprxss_state *dp, u32 addr,
+			   u32 clr_mask, u32 set_data)
+{
+	u32 regval;
+
+	regval = xdprxss_read(dp, addr);
+	regval &= ~clr_mask;
+	regval |= FIELD_PREP(clr_mask, set_data);
+	xdprxss_write(dp, addr, regval);
+}
+
+static inline void xdprxss_dpcd_update_start(struct xdprxss_state *xdprxss)
+{
+	iowrite32(0x1, xdprxss->dp_base + XDPRX_CTRL_DPCD_REG);
+}
+
+static inline void xdprxss_dpcd_update_end(struct xdprxss_state *xdprxss)
+{
+	iowrite32(0x0, xdprxss->dp_base + XDPRX_CTRL_DPCD_REG);
+}
+
+static inline int xdprxss_get_lane01_reqval(struct xdprxss_state *xdprxss)
+{
+	return xdprxss_read(xdprxss, XDPRX_DPCD_LANE01_STATUS) &
+			    XDPRX_LANE01_PEVS_MASK;
+}
+
+/**
+ * xdprxss_dpcd_update - Update the DPCD registers
+ * @xdprxss: pointer to driver state
+ * @addr: DPCD register address
+ * @val: Value to be override
+ * This function is used to override the DPCD registers set.
+ * DPCD register set is ranges from 0x084-0x0f0.
+ * Register 0x0B8(direct_dpcd_access) must be set to 1 to
+ * override DPCD values
+ */
+static inline void xdprxss_dpcd_update(struct xdprxss_state *xdprxss,
+				       u32 addr, u32 val)
+{
+	xdprxss_write(xdprxss, addr, val);
+}
+
+static inline void xdprxss_soft_video_reset(struct xdprxss_state *xdprxss)
+{
+	xdprxss_write(xdprxss, XDPRX_SOFT_RST_REG, XDPRX_SOFT_VIDRST_MASK);
+	xdprxss_write(xdprxss, XDPRX_SOFT_RST_REG, 0x0);
+}
+
+/**
+ * xlnx_dp_phy_ready - check if PHY is ready
+ * @dp: DisplayPort IP core structure
+ *
+ * check if PHY is ready. If PHY is not ready, wait 1ms to check for 100 times.
+ * This amount of delay was suggested by IP designer.
+ *
+ * Return: 0 if PHY is ready, or -ENODEV if PHY is not ready.
+ */
+static int xlnx_dp_phy_ready(struct xdprxss_state *dp)
+{
+	u32 i, reg, ready;
+
+	ready = XDPRX_PHYSTATUS_ALL_LANES_GOOD_MASK;
+
+	/* Wait for 100ms. This should be enough time for PHY to be ready */
+	for (i = 0; i < XDPRX_PHYSTATUS_READ_COUNT; i++) {
+		reg = xdprxss_read(dp, XDPRX_PHYSTATUS_REG);
+		if ((reg & ready) == ready)
+			break;
+
+		usleep_range(1000, 1100);
+	}
+
+	if (i == XDPRX_PHYSTATUS_READ_COUNT) {
+		dev_err(dp->dev, "PHY isn't ready\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static void config_rx_dec_clk(struct xdprxss_state *dp, int bw_code)
+{
+	u8 p5_fedge_en, o_val, d_val, m_val;
+	u16 hightime, div_edge;
+	u32 reg;
+
+	/*
+	 * Configuring MMCM to give a /20 clock output for /16 clk input.
+	 *
+	 * GT ch0outclk (/16) --> MMCM --> /20 clock
+	 *
+	 * Thus:
+	 * 8.1G  : Input MMCM clock is 506.25, output is 405
+	 * 5.4G  : Input MMCM clock is 337.5, output is 270
+	 * 2.7G  : Input MMCM clock is 168.75, output is 135
+	 * 1.62G : Input MMCM clock is 101.25, output is 81
+	 */
+	switch (bw_code) {
+	case DP_LINK_BW_8_1:
+		m_val = XDPRX_MMCM_M_VAL_405;
+		break;
+	case DP_LINK_BW_5_4:
+		m_val = XDPRX_MMCM_M_VAL_270;
+		break;
+	case DP_LINK_BW_2_7:
+		m_val = XDPRX_MMCM_M_VAL_135;
+		break;
+	default:
+		m_val = XDPRX_MMCM_M_VAL_81;
+	}
+	d_val = XDPRX_MMCM_D_VAL;
+	o_val = m_val / XDPRX_MMCM_M_O_VAL_RATIO;
+
+	/*
+	 * MMCM is dynamically programmed for the respective rate
+	 * using the M, D, Div values
+	 */
+	hightime = o_val / MMCM_O_VAL_HIGHTIME_DIVIDER;
+	reg = XDPRX_MMCM_REG3_PREDIV2 | XDPRX_MMCM_REG3_USED | XDPRX_MMCM_REG3_MX;
+	if (o_val % MMCM_O_VAL_EDGE_DIVIDER > 1)
+		reg |= BIT(8);
+
+	p5_fedge_en = o_val % MMCM_O_VAL_FEDGE_DIVIDER;
+	reg |= p5_fedge_en << XDPRX_MMCM_CLKOUT0_P5EN_SHIFT |
+		p5_fedge_en << XDPRX_MMCM_CLKOUT0_P5FEDGE_SHIFT;
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG3_OFFSET, reg);
+	reg = hightime | hightime << MMCM_MDO_VAL_HIGHTIME_SHIFT;
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG4_OFFSET, reg);
+
+	/* Implement D */
+	reg = 0;
+	div_edge = d_val % MMCM_D_VAL_EDGE_DIVIDER;
+	hightime = d_val / MMCM_D_VAL_HIGHTIME_DIVIDER;
+	reg = reg | div_edge << XDPRX_MMCM_REG12_EDGE_SHIFT;
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG12_OFFSET, reg);
+	reg = hightime | hightime << MMCM_MDO_VAL_HIGHTIME_SHIFT;
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG13_OFFSET, reg);
+
+	/* Implement M */
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG25_OFFSET, 0);
+
+	div_edge = m_val % MMCM_M_VAL_EDGE_DIVIDER;
+	hightime = m_val / MMCM_M_VAL_HIGHTIME_DIVIDER;
+	reg = hightime | hightime << MMCM_MDO_VAL_HIGHTIME_SHIFT;
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG2_OFFSET, reg);
+	reg = XDPRX_MMCM_REG1_PREDIV2 | XDPRX_MMCM_REG1_EN | XDPRX_MMCM_REG1_MX;
+
+	if (div_edge)
+		reg = reg | XDPRX_MMCM_REG1_EDGE_MASK;
+	else
+		reg = reg & ~XDPRX_MMCM_REG1_EDGE_MASK;
+
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG1_OFFSET, reg);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG11_OFFSET, XDPRX_MMCM_REG11_VAL);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG14_OFFSET, XDPRX_MMCM_REG14_VAL);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG15_OFFSET, XDPRX_MMCM_REG15_VAL);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG16_OFFSET, XDPRX_MMCM_REG16_VAL);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG17_OFFSET, XDPRX_MMCM_REG17_VAL);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_REG26_OFFSET, XDPRX_MMCM_REG26_VAL);
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_RECONFIG_OFFSET,
+			   XDPRX_MMCM_RECONFIG_LOAD | XDPRX_MMCM_RECONFIG_SADDR);
+}
+
+static int get_rx_dec_clk_lock(struct xdprxss_state *dp)
+{
+	u32 retry = 0;
+
+	/* MMCM issued a reset */
+	xdprxss_mmcm_write(dp, XDPRX_MMCM_SWRST_OFFSET, XDPRX_MMCM_SWRST_VAL);
+	while (!(xdprxss_mmcm_read(dp, XDPRX_MMCM_STATUS_OFFSET) & BIT(0))) {
+		if (retry == XDPRX_MMCM_STATUS_RETRY)
+			return -ENODEV;
+
+		usleep_range(1000, 1100);
+		retry++;
+	}
+
+	return 0;
+}
+
+static int config_gt_control_linerate(struct xdprxss_state *dp, int bw_code)
+{
+	u32 data;
+
+	switch (bw_code) {
+	case DP_LINK_BW_1_62:
+		data = XDPRX_GTCTL_LINE_RATE_162G;
+		break;
+	case DP_LINK_BW_2_7:
+		data = XDPRX_GTCTL_LINE_RATE_270G;
+		break;
+	case DP_LINK_BW_5_4:
+		data = XDPRX_GTCTL_LINE_RATE_540G;
+		break;
+	case DP_LINK_BW_8_1:
+		data = XDPRX_GTCTL_LINE_RATE_810G;
+		break;
+	default:
+		data = XDPRX_GTCTL_LINE_RATE_810G;
+	}
+
+	xdprxss_clrset(dp, XDPRX_GTCTL_REG, XDPRX_GTCTL_LINE_RATE_MASK, data);
+
+	return xlnx_dp_phy_ready(dp);
+}
+
+static int xlnx_dp_rx_gt_control_init(struct xdprxss_state *dp)
+{
+	int ret;
+
+	/* setting initial vswing */
+	xdprxss_clrset(dp, XDPRX_GTCTL_REG, XDPRX_GTCTL_VSWING_MASK,
+		       XDPRX_GTCTL_VSWING_INIT_VAL);
+
+	xdprxss_clr(dp, XDPRX_GTCTL_REG, XDPRX_GTCTL_EN);
+	ret = xlnx_dp_phy_ready(dp);
+	if (ret < 0)
+		return ret;
+
+	/* Setting initial link rate */
+	ret = config_gt_control_linerate(dp, DP_LINK_BW_8_1);
+	if (ret) {
+		dev_err(dp->dev, "Default Line Rate setting Failed\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void xdprxss_dtg_disable(struct xdprxss_state *state)
+{
+	xdprxss_write(state, XDPRX_DTG_REG, XDPRX_DTG_DIS_MASK);
+	xdprxss_soft_video_reset(state);
+}
+
+/**
+ * xdprxss_get_stream_properties - Get DP Rx stream properties
+ * @state: pointer to driver state
+ * This function decodes the stream to get stream properties
+ * like width, height, format, picture type (interlaced/progressive),etc.
+ *
+ * Return: 0 for success else errors
+ */
+static int xdprxss_get_stream_properties(struct xdprxss_state *state)
+{
+	struct v4l2_mbus_framefmt *format = &state->format;
+	struct v4l2_dv_timings *dv_timings = &state->detected_timings;
+	u32 rxmsa_mvid, rxmsa_nvid, rxmsa_misc, recv_clk_freq, linkrate, data;
+	u16 vres_total, hres_total, framerate, lanecount;
+	u16 hact, vact, hsw, vsw, hstart, vstart;
+	u8 pixel_width, fmt;
+	u16 read_val;
+
+	rxmsa_mvid = xdprxss_read(state, XDPRX_MSA_MVID_REG);
+	rxmsa_nvid = xdprxss_read(state, XDPRX_MSA_NVID_REG);
+
+	hact = xdprxss_read(state, XDPRX_MSA_HRES_REG);
+
+	vact = xdprxss_read(state, XDPRX_MSA_VHEIGHT_REG);
+	rxmsa_misc = xdprxss_read(state, XDPRX_MSA_MISC0_REG);
+
+	vres_total = xdprxss_read(state, XDPRX_MSA_VTOTAL_REG);
+	hres_total = xdprxss_read(state, XDPRX_MSA_HTOTAL_REG);
+	linkrate = xdprxss_read(state, XDPRX_LINK_BW_REG);
+	lanecount = xdprxss_read(state, XDPRX_LANE_COUNT_REG);
+	hstart = xdprxss_read(state, XDPRX_MSA_HSTART_REG);
+	vstart = xdprxss_read(state, XDPRX_MSA_VSTART_REG);
+	hsw = xdprxss_read(state, XDPRX_MSA_HSWIDTH_REG);
+	vsw = xdprxss_read(state, XDPRX_MSA_VSWIDTH_REG);
+
+	recv_clk_freq = (linkrate * 27 * rxmsa_mvid) / rxmsa_nvid;
+
+	if (recv_clk_freq > 540 && lanecount == 4)
+		pixel_width = 0x4;
+	else if (recv_clk_freq > 270 && (lanecount != 1))
+		pixel_width = 0x2;
+	else
+		pixel_width = 0x1;
+
+	framerate = (recv_clk_freq * MHZ) / (hres_total * vres_total);
+	framerate = roundup(framerate, 5);
+	xdprxss_write(state, XDPRX_LINERST_DIS_REG, 0x1);
+	/* set pixel mode as per lane count and reset the DTG */
+	read_val = xdprxss_read(state, XDPRX_DTG_REG);
+	xdprxss_write(state, XDPRX_DTG_REG, (read_val & XDPRX_DTG_DIS_MASK));
+	xdprxss_write(state, XDPRX_PIXEL_WIDTH_REG, pixel_width);
+	read_val = xdprxss_read(state, XDPRX_DTG_REG);
+	xdprxss_write(state, XDPRX_DTG_REG, (read_val | 0x1));
+	fmt = FIELD_GET(XDPRX_MSA_FMT_MASK, rxmsa_misc);
+	state->bpc = FIELD_GET(XDPRX_MSA_BPC_MASK, rxmsa_misc);
+
+	switch (fmt) {
+	case XDPRX_COLOR_FORMAT_422:
+		if (state->bpc == 10)
+			format->code = MEDIA_BUS_FMT_UYVY10_1X20;
+		else
+			format->code = MEDIA_BUS_FMT_UYVY8_1X16;
+		break;
+	case XDPRX_COLOR_FORMAT_444:
+		if (state->bpc == 10)
+			format->code = MEDIA_BUS_FMT_VUY10_1X30;
+		else
+			format->code = MEDIA_BUS_FMT_VUY8_1X24;
+		break;
+	case XDPRX_COLOR_FORMAT_RGB:
+		if (state->bpc == 10)
+			format->code = MEDIA_BUS_FMT_RBG101010_1X30;
+		else
+			format->code = MEDIA_BUS_FMT_RBG888_1X24;
+		break;
+	default:
+		dev_err(state->dev, "Unsupported color format\n");
+
+		return -EINVAL;
+	}
+
+	dv_timings->type = V4L2_DV_BT_656_1120;
+	/*
+	 * TODO : For now driver supports only progressive video.
+	 * In future, driver may add with other interlace support
+	 */
+	dv_timings->bt.interlaced = false;
+	dv_timings->bt.width = hact;
+	dv_timings->bt.height = vact;
+	dv_timings->bt.polarities = 0;
+
+	data = xdprxss_read(state, XDPRX_MSA_HSPOL_REG);
+	if (data & XDPRX_MSA_HSPOL_MASK)
+		dv_timings->bt.polarities = V4L2_DV_HSYNC_POS_POL;
+
+	data = xdprxss_read(state, XDPRX_MSA_VSPOL_REG);
+	if (data & XDPRX_MSA_VSPOL_MASK)
+		dv_timings->bt.polarities |= V4L2_DV_VSYNC_POS_POL;
+
+	dv_timings->bt.pixelclock = vres_total * hres_total * framerate;
+	dv_timings->bt.hsync = hsw;
+	dv_timings->bt.hfrontporch = (hres_total - (hact + hstart));
+	dv_timings->bt.hbackporch = hstart - hsw;
+	dv_timings->bt.vsync = vsw;
+	dv_timings->bt.vfrontporch = (vres_total - (vact + vstart));
+	dv_timings->bt.vbackporch = vstart - vsw;
+
+	spin_lock(&state->lock);
+	format->width = dv_timings->bt.width;
+	format->height = dv_timings->bt.height;
+	format->colorspace = V4L2_COLORSPACE_REC709;
+	format->xfer_func = V4L2_XFER_FUNC_DEFAULT;
+	format->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+	format->quantization = V4L2_QUANTIZATION_DEFAULT;
+	format->field = V4L2_FIELD_NONE;
+	state->frame_interval = framerate;
+	spin_unlock(&state->lock);
+
+	dev_dbg(state->dev, "detected properties : width %d height %d\n",
+		dv_timings->bt.width, dv_timings->bt.height);
+
+	return 0;
+}
+
+static void xdprxss_set_training_params(struct xdprxss_state *xdprxss)
+{
+	unsigned int offset;
+
+	/*
+	 * This register is used to set a minimum value which must be met
+	 * As per the Display Port protocol.The internal logic forces training
+	 * to fail until this value is met.Please refer to PG 300
+	 * https://www.xilinx.com/support/documentation/ip_documentation/dp_rx_subsystem/v2_1/pg233-displayport-rx-subsystem.pdf
+	 */
+	xdprxss_write(xdprxss, XDPRX_MINVOLT_SWING_REG, XDPRX_MIN_VS_MASK);
+	xdprxss_write(xdprxss, XDPRX_AUX_CLKDIV_REG,
+		      xdprxss_read(xdprxss, XDPRX_AUX_CLKDIV_REG) |
+		      FIELD_PREP(XDPRX_AUX_DEFER_MASK, XDPRX_AUX_DEFER_COUNT));
+
+	xdprxss_dpcd_update_start(xdprxss);
+	xdprxss_dpcd_update(xdprxss, XDPRX_TP_SET_REG,
+			    (XDPRX_AUX_RDINT_16MS << XDPRX_AUX_RDINT_SHIFT) |
+			    XDPRX_AUX_READINTRVL_REG);
+	xdprxss_dpcd_update_end(xdprxss);
+
+	xdprxss_clr(xdprxss, XDPRX_INTR_MASK_REG, XDPRX_INTR_ALL_MASK);
+
+	/* Load edid data to EDID memory block */
+	for (offset = 0; offset < XDPRX_EDID_LENGTH; offset = offset + 4) {
+		iowrite32((uint32_t)xilinx_edid[offset / 4],
+			  xdprxss->edid_base + offset);
+	}
+	xdprxss_write(xdprxss, XDPRX_LOCAL_EDID_REG, 0x1);
+
+	/* Disable all the interrupts */
+	xdprxss_set(xdprxss, XDPRX_INTR_MASK_REG, XDPRX_INTR_ALL_MASK);
+	xdprxss_disable_allintr_1(xdprxss);
+
+	/* Enable trainng related interrupts */
+	xdprxss_clr(xdprxss, XDPRX_INTR_MASK_REG, XDPRX_INTR_TRNG_MASK);
+	xdprxss_enable_training_intr_1(xdprxss);
+
+	xdprxss_write(xdprxss, XDPRX_AUX_CLKDIV_REG,
+		      xdprxss_read(xdprxss, XDPRX_AUX_CLKDIV_REG) |
+		      FIELD_PREP(XDPRX_AUX_DEFER_MASK, XDPRX_AUX_DEFER_COUNT));
+	xdprxss_write(xdprxss, XDPRX_BSIDLE_TIME_REG, XDPRX_BSIDLE_TMOUT_VAL);
+	xdprxss_clr(xdprxss, XDPRX_CRC_CONFIG_REG, XDPRX_CRC_EN_MASK);
+	xdprxss_write(xdprxss, XDPRX_LINK_ENABLE_REG, 0x1);
+}
+
+static void xdprxss_core_init(struct xdprxss_state *xdprxss)
+{
+	unsigned long axi_clk;
+
+	u32 max_lanecount = xdprxss->max_lanecount;
+
+	xdprxss_dpcd_update_start(xdprxss);
+	xdprxss_dpcd_update(xdprxss,
+			    XDPRX_VRD_BWSET_REG, xdprxss->max_linkrate);
+	xdprxss_update_ext_rcv_cap(xdprxss, xdprxss->max_linkrate);
+	max_lanecount |= (XDPRX_EFRAME_CAP_MASK | XDPRX_LNCNT_TPS3_MASK);
+	xdprxss_dpcd_update(xdprxss, XDPRX_LANE_CNT_REG, max_lanecount);
+	xdprxss_dpcd_update_end(xdprxss);
+	xdprxss_write(xdprxss, XDPRX_LINK_ENABLE_REG, 0x0);
+	axi_clk = clk_get_rate(xdprxss->axi_clk);
+	xdprxss_write(xdprxss, XDPRX_AUX_CLKDIV_REG, axi_clk / MHZ);
+	/* Put both GT RX/TX and CPLL into reset */
+	xdprxss_write(xdprxss, XDPRX_PHY_REG, XDPRX_PHY_GTPLLRST_MASK |
+		      XDPRX_PHY_GTRXRST_MASK);
+	/* Release CPLL reset */
+	xdprxss_write(xdprxss, XDPRX_PHY_REG, XDPRX_PHY_GTRXRST_MASK);
+	xdprxss_set_clk_data_recovery_timeout_val(xdprxss,
+						  XDPRX_CDRCTRL_TDLOCK_VAL);
+	/*
+	 * Remove the reset from the PHY and configure to issue reset after
+	 * every training iteration, link rate change, and start of training
+	 * pattern
+	 */
+	xdprxss_write(xdprxss, XDPRX_PHY_REG,
+		      XDPRX_PHYRST_ENBL_MASK |
+		      XDPRX_PHYRST_TRITER_MASK |
+		      XDPRX_PHYRST_RATECHANGE_MASK |
+		      XDPRX_PHYRST_TP1START_MASK);
+	xdprxss_write(xdprxss, XDPRX_MST_CAP_REG, 0x0);
+	xdprxss_write(xdprxss, XDPRX_SINK_COUNT_REG, 1);
+	xdprxss_enable_training_timeout(xdprxss);
+	xdprxss_set_training_params(xdprxss);
+}
+
+static void xdprxss_irq_unplug(struct xdprxss_state *state)
+{
+	dev_dbg(state->dev, "Asserted cable unplug interrupt\n");
+
+	xdprxss_set(state, XDPRX_SOFT_RST_REG, XDPRX_SOFT_VIDRST_MASK);
+	xdprxss_clr(state, XDPRX_SOFT_RST_REG, XDPRX_SOFT_VIDRST_MASK);
+
+	if (state->retimer_prvdata)
+		state->retimer_prvdata->retimer_rst_dp_path();
+
+	/*
+	 * Disable unplug interrupt so that no unplug event when RX is
+	 * disconnected
+	 */
+	xdprxss_disable_unplug_intr(state);
+	xdprxss_generate_hpd_intr(state, XDPRX_HPD_PULSE_750);
+
+	xdprxss_disable_allintr(state);
+	xdprxss_disable_allintr_1(state);
+
+	xdprxss_enable_training_intr(state);
+	xdprxss_enable_training_intr_1(state);
+	/*
+	 * In a scenario, where the cable is plugged-in but the training
+	 * is lost, the software is expected to assert a HPD upon the
+	 * occurrence of a TRAINING_LOST interrupt, so that the Source
+	 * can retrain the link.
+	 */
+	xdprxss_write(state, XDPRX_HPD_INTR_REG,
+		      FIELD_PREP(XDPRX_HPD_PULSE_MASK, XDPRX_HPD_PULSE_5000) |
+		      XDPRX_HPD_INTR_MASK);
+}
+
+static void xdprxss_irq_tp1(struct xdprxss_state *state)
+{
+	union phy_configure_opts phy_opts = { 0 };
+	struct phy_configure_opts_dp *phy_cfg = &phy_opts.dp;
+	u32 linkrate;
+	unsigned int i;
+
+	dev_dbg(state->dev, "Asserted traning pattern 1\n");
+
+	linkrate = xdprxss_read(state, XDPRX_LINK_BW_REG);
+
+	switch (linkrate) {
+	case DP_LINK_BW_1_62:
+	case DP_LINK_BW_2_7:
+	case DP_LINK_BW_5_4:
+	case DP_LINK_BW_8_1:
+		phy_cfg->link_rate = linkrate * 270;
+		break;
+	default:
+		dev_err(state->dev, "invalid link rate\n");
+		break;
+	}
+
+	if (state->retimer_prvdata) {
+		state->retimer_prvdata->retimer_rst_cr_path();
+		state->retimer_prvdata->retimer_access_laneset();
+	}
+
+	if (!state->versal_gt_present) {
+		phy_cfg->set_rate = 1;
+		for (i = 0; i < state->max_lanecount; i++)
+			phy_configure(state->phy[i], &phy_opts);
+		/* Initialize phy logic of DP-RX core */
+		xdprxss_write(state, XDPRX_PHY_REG, XDPRX_PHY_INIT_MASK);
+		phy_reset(state->phy[0]);
+	} else {
+		config_rx_dec_clk(state, linkrate);
+
+		config_gt_control_linerate(state, linkrate);
+
+		if (get_rx_dec_clk_lock(state))
+			dev_info(state->dev, "rx decryption clock failed to lock\n");
+
+		/* Initialize phy logic of DP-RX core */
+		xdprxss_write(state, XDPRX_PHY_REG, XDPRX_PHY_INIT_MASK);
+	}
+	state->ltstate = 1;
+	xdprxss_clr(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_ALL_MASK);
+}
+
+static void xdprxss_irq_tp2(struct xdprxss_state *state)
+{
+	dev_dbg(state->dev, "Asserted traning pattern 2\n");
+	state->ltstate = 2;
+}
+
+static void xdprxss_training_failure(struct xdprxss_state *state)
+{
+	dev_dbg(state->dev, "Traning Lost !!\n");
+	state->valid_stream = false;
+
+	xdprxss_write(state, XDPRX_HPD_INTR_REG,
+		      FIELD_PREP(XDPRX_HPD_PULSE_MASK, XDPRX_HPD_PULSE_750) |
+		      XDPRX_HPD_INTR_MASK);
+
+	/* reset the aux logic */
+	xdprxss_set(state, XDPRX_SOFT_RST_REG, XDPRX_SOFT_AUXRST_MASK);
+	xdprxss_clr(state, XDPRX_SOFT_RST_REG, XDPRX_SOFT_AUXRST_MASK);
+	xdprxss_disable_audio(state);
+}
+
+static void xdprxss_irq_no_video(struct xdprxss_state *state)
+{
+	dev_dbg(state->dev, "No Valid video received !!\n");
+
+	xdprxss_write(state, XDPRX_VIDEO_UNSUPPORTED_REG, 0x1);
+	xdprxss_clr(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_VBLANK_MASK);
+	xdprxss_set(state, XDPRX_INTR_MASK_REG, XDPRX_INTR_NOVID_MASK);
+
+	xdprxss_dtg_disable(state);
+	xdprxss_dtg_enable(state);
+
+	xdprxss_enable_audio_intr(state);
+
+	/* notify source change event */
+	memset(&state->event, 0, sizeof(state->event));
+	state->event.type = V4L2_EVENT_SOURCE_CHANGE;
+	state->event.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION;
+	v4l2_subdev_notify_event(&state->subdev, &state->event);
+	state->valid_stream = false;
+}
+
+static void xdprxss_irq_valid_video(struct xdprxss_state *state)
+{
+	dev_dbg(state->dev, "Valid Video received !!\n");
+	xdprxss_write(state, XDPRX_VIDEO_UNSUPPORTED_REG, 0x0);
+
+	if (!xdprxss_get_stream_properties(state)) {
+		memset(&state->event, 0, sizeof(state->event));
+		state->event.type = V4L2_EVENT_SOURCE_CHANGE;
+		state->event.u.src_change.changes =
+				V4L2_EVENT_SRC_CH_RESOLUTION;
+		v4l2_subdev_notify_event(&state->subdev, &state->event);
+		state->valid_stream = true;
+	} else {
+		dev_err(state->dev, "Unable to get stream properties!\n");
+		state->valid_stream = false;
+	}
+}
+
+static void xdprxss_irq_audio_detected(struct xdprxss_state *state)
+{
+	u32 buff[INFO_PCKT_SIZE_WORDS];
+	u8 *buf_ptr;
+	int i;
+
+	for (i = 0; i < INFO_PCKT_SIZE_WORDS; i++)
+		buff[i] = xdprxss_read(state, XDPRX_AUDIO_INFO_DATA);
+
+	buf_ptr = (u8 *)buff;
+	memcpy(state->rx_audio_data->infoframe, buff, INFO_PCKT_SIZE);
+
+	if (buf_ptr[1] == INFO_PCKT_TYPE_AUDIO)
+		state->rx_audio_data->audio_detected = true;
+}
+
+static void xdprxss_irq_access_laneset(struct xdprxss_state *state)
+{
+	u32 read_val;
+	u8 training;
+
+	training = xdprxss_read(state, XDPRX_DPCD_TRAINING_PATTERN_SET);
+
+	if (state->ltstate == 2 && training != 1) {
+		read_val = xdprxss_get_lane01_reqval(state);
+
+		if (state->ce_req_val != read_val && state->retimer_prvdata)
+			state->retimer_prvdata->retimer_access_laneset();
+
+		/* Update the value to be used in next round */
+		state->ce_req_val = xdprxss_get_lane01_reqval(state);
+	}
+}
+
+static void xdprxss_irq_access_linkqual(struct xdprxss_state *state)
+{
+	u32 read_val;
+
+	read_val = xdprxss_read(state, XDPRX_DPC_LINK_QUAL_CONFIG);
+
+	if ((read_val & XDPRX_LINK_QUAL_PRBS_MODE_MASK) ==
+	    XDPRX_DPCD_LINK_QUAL_PRBS_MASK) {
+		/* enable PRBS mode in video phy */
+		state->vidphy_prvdata->vidphy_prbs_mode(1);
+		/* enable PRBS mode in retimer */
+		state->retimer_prvdata->retimer_prbs_mode(1);
+	} else {
+		/* disable PRBS mode in video phy */
+		state->vidphy_prvdata->vidphy_prbs_mode(0);
+		/* disable PRBS mode in retimer */
+		state->retimer_prvdata->retimer_prbs_mode(0);
+	}
+}
+
+static irqreturn_t xdprxss_irq_handler(int irq, void *dev_id)
+{
+	struct xdprxss_state *state = (struct xdprxss_state *)dev_id;
+	u32 status, status1;
+
+	status = xdprxss_read(state, XDPRX_INTR_CAUSE_REG);
+	status &= ~xdprxss_read(state, XDPRX_INTR_MASK_REG);
+
+	status1 = xdprxss_read(state, XDPRX_INTR_CAUSE_1_REG);
+	status1 &= ~xdprxss_read(state, XDPRX_INTR_MASK_1_REG);
+
+	if (!status)
+		return IRQ_NONE;
+
+	if (status1 & XDPRX_INTR_ACCESS_LANE_SET_MASK)
+		xdprxss_irq_access_laneset(state);
+	if (status1 & XDPRX_INTR_LINKQUAL_MASK)
+		xdprxss_irq_access_linkqual(state);
+	if (status & XDPRX_INTR_UNPLUG_MASK)
+		schedule_delayed_work(&state->unplug_work, 0);
+	if (status & XDPRX_INTR_TP1_MASK)
+		schedule_delayed_work(&state->tp1_work, 0);
+	if (status & XDPRX_INTR_TP2_MASK)
+		xdprxss_irq_tp2(state);
+	if (status & XDPRX_INTR_TRLOST_MASK)
+		xdprxss_training_failure(state);
+	if (status & XDPRX_INTR_NOVID_MASK)
+		xdprxss_irq_no_video(state);
+	if (status & XDPRX_INTR_VID_MASK)
+		xdprxss_irq_valid_video(state);
+	if (status & XDPRX_INTR_AUDIO_MASK)
+		xdprxss_irq_audio_detected(state);
+#ifdef DEBUG
+	if (status & XDPRX_INTR_TRDONE_MASK)
+		dev_dbg(state->dev, "DP Link training is done !!\n");
+#endif
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xdprxss_subscribe_event - Subscribe to video source change event
+ * @sd: V4L2 Sub device
+ * @fh: V4L2 File Handle
+ * @sub: Subcribe event structure
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int xdprxss_subscribe_event(struct v4l2_subdev *sd,
+				   struct v4l2_fh *fh,
+				   struct v4l2_event_subscription *sub)
+{
+	int ret;
+	struct xdprxss_state *xdprxss = to_xdprxssstate(sd);
+
+	dev_dbg(xdprxss->dev, "Event subscribed : 0x%08x\n", sub->type);
+
+	switch (sub->type) {
+	case V4L2_EVENT_SOURCE_CHANGE:
+		ret = v4l2_src_change_event_subscribe(fh, sub);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static int xdprxss_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct xdprxss_state *xdprxss = to_xdprxssstate(sd);
+
+	/* DP does not need to be enabled when we start streaming */
+	if (enable == xdprxss->streaming)
+		return 0;
+
+	if (enable && !xdprxss->valid_stream)
+		return -EINVAL;
+
+	xdprxss->streaming = enable;
+
+	return 0;
+}
+
+/**
+ * xdprxss_g_input_status - It is used to determine if the video signal
+ * is present / locked onto or not.
+ *
+ * @sd: V4L2 Sub device
+ * @status: status of signal locked
+ *
+ * This is used to determine if the valid video signal is present and
+ * locked onto by the DP Rx xdprxss or not .
+ *
+ * Return: zero on success
+ */
+static int xdprxss_g_input_status(struct v4l2_subdev *sd, u32 *status)
+{
+	struct xdprxss_state *xdprxss = to_xdprxssstate(sd);
+
+	if (!xdprxss->valid_stream)
+		*status = V4L2_IN_ST_NO_SYNC | V4L2_IN_ST_NO_SIGNAL;
+	else
+		*status = 0;
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+__xdprxss_get_pad_format(struct xdprxss_state *xdprxss,
+			 struct v4l2_subdev_state *sd_state,
+			 unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xdprxss->subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xdprxss->format;
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+/**
+ * xdprxss_init_cfg - Initialise the pad format config to default
+ * @sd: Pointer to V4L2 Sub device structure
+ * @sd_state: Pointer to sub device pad information structure
+ *
+ * This function is used to initialize the pad format with the default
+ * values.
+ *
+ * Return: 0 on success
+ */
+static int xdprxss_init_cfg(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_state *sd_state)
+{
+	struct xdprxss_state *xdprxss = to_xdprxssstate(sd);
+	struct v4l2_mbus_framefmt *format;
+
+	format = v4l2_subdev_get_try_format(sd, sd_state, 0);
+
+	if (!xdprxss->valid_stream)
+		*format = xdprxss->format;
+
+	return 0;
+}
+
+/**
+ * xdprxss_getset_format - This is used to set and get the pad format
+ * @sd: Pointer to V4L2 Sub device structure
+ * @sd_state: Pointer to sub device pad information structure
+ * @fmt: Pointer to pad level media bus format
+ *
+ * This function is used to set the pad format.
+ * Since the pad format is fixed in hardware, it can't be
+ * modified on run time.
+ *
+ * Return: 0 on success
+ */
+static int xdprxss_getset_format(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct xdprxss_state *xdprxss = to_xdprxssstate(sd);
+	struct v4l2_mbus_framefmt *format;
+
+	if (!xdprxss->valid_stream) {
+		dev_err(xdprxss->dev, "Video not locked!\n");
+		return -EINVAL;
+	}
+
+	dev_dbg(xdprxss->dev,
+		"set width %d height %d code %d field %d colorspace %d\n",
+		fmt->format.width, fmt->format.height,
+		fmt->format.code, fmt->format.field,
+		fmt->format.colorspace);
+	format = __xdprxss_get_pad_format(xdprxss, sd_state,
+					  fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+/**
+ * xdprxss_enum_mbus_code - Handle pixel format enumeration
+ * @sd: pointer to v4l2 subdev structure
+ * @sd_state: V4L2 subdev pad configuration
+ * @code: pointer to v4l2_subdev_mbus_code_enum structure
+ *
+ * Return: -EINVAL or zero on success
+ */
+static int xdprxss_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct xdprxss_state *xdprxss = to_xdprxssstate(sd);
+	u32 index = code->index;
+	u32 base = 0;
+
+	if (xdprxss->bpc == 8)
+		base = 0;
+
+	if (xdprxss->bpc == 10)
+		base = 3;
+
+	if (code->pad || index >= 3)
+		return -EINVAL;
+
+	code->code = xdprxss_supported_mbus_fmts[base + index];
+
+	return 0;
+}
+
+/**
+ * xdprxss_enum_dv_timings - Enumerate all the supported DV timings
+ * @sd: pointer to v4l2 subdev structure
+ * @timings: DV timings structure to be returned.
+ *
+ * Return: -EINVAL incase of invalid index and pad or zero on success
+ */
+static int xdprxss_enum_dv_timings(struct v4l2_subdev *sd,
+				   struct v4l2_enum_dv_timings *timings)
+{
+	if (timings->index >= ARRAY_SIZE(fmt_cap))
+		return -EINVAL;
+
+	if (timings->pad != 0)
+		return -EINVAL;
+
+	timings->timings = fmt_cap[timings->index];
+
+	return 0;
+}
+
+/**
+ * xdprxss_get_dv_timings_cap - This is used to set the dv timing
+ * capabilities
+ * @subdev: Pointer to V4L2 Sub device structure
+ * @cap: Pointer to dv timing capability structure
+ *
+ * Return: -EINVAL incase of invalid pad or zero on success
+ */
+static int xdprxss_get_dv_timings_cap(struct v4l2_subdev *subdev,
+				      struct v4l2_dv_timings_cap *cap)
+{
+	struct v4l2_dv_timings_cap xdprxss_dv_timings_cap = {
+		.type = V4L2_DV_BT_656_1120,
+		.reserved = { 0 },
+		V4L2_INIT_BT_TIMINGS
+		(800, 7680,
+		600, 4320,
+		25000000, 297000000,
+		V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT |
+		V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT,
+		V4L2_DV_BT_CAP_INTERLACED | V4L2_DV_BT_CAP_PROGRESSIVE |
+		V4L2_DV_BT_CAP_REDUCED_BLANKING |
+		V4L2_DV_BT_CAP_CUSTOM
+		)
+	};
+
+	if (cap->pad != 0)
+		return -EINVAL;
+
+	*cap = xdprxss_dv_timings_cap;
+
+	return 0;
+}
+
+static int xdprxss_query_dv_timings(struct v4l2_subdev *sd,
+				    struct v4l2_dv_timings *timings)
+{
+	struct xdprxss_state *state = to_xdprxssstate(sd);
+
+	if (!timings)
+		return -EINVAL;
+
+	if (!state->valid_stream)
+		return -ENOLCK;
+
+	*timings = state->detected_timings;
+
+	return 0;
+}
+
+/* ------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xdprxss_media_ops = {
+	.link_validate = v4l2_subdev_link_validate
+};
+
+static const struct v4l2_subdev_core_ops xdprxss_core_ops = {
+	.subscribe_event	= xdprxss_subscribe_event,
+	.unsubscribe_event	= v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops xdprxss_video_ops = {
+	.query_dv_timings	= xdprxss_query_dv_timings,
+	.s_stream		= xdprxss_s_stream,
+	.g_input_status		= xdprxss_g_input_status,
+};
+
+static const struct v4l2_subdev_pad_ops xdprxss_pad_ops = {
+	.init_cfg		= xdprxss_init_cfg,
+	.enum_mbus_code		= xdprxss_enum_mbus_code,
+	.get_fmt		= xdprxss_getset_format,
+	.set_fmt		= xdprxss_getset_format,
+	.enum_dv_timings	= xdprxss_enum_dv_timings,
+	.dv_timings_cap         = xdprxss_get_dv_timings_cap,
+};
+
+static const struct v4l2_subdev_ops xdprxss_ops = {
+	.core	= &xdprxss_core_ops,
+	.video	= &xdprxss_video_ops,
+	.pad	= &xdprxss_pad_ops
+};
+
+/* ----------------------------------------------------------------
+ * DP audio operation
+ */
+/**
+ * xlnx_rx_pcm_startup - initialize audio during audio usecase
+ *
+ * @substream: Pointer to sound pcm substream structure
+ * @dai: Pointer to sound soc dai structure
+ *
+ * This function is called by ALSA framework before audio
+ * capture begins.
+ *
+ * Return: -EIO if no audio is detected or 0 on success
+ */
+static int xlnx_rx_pcm_startup(struct snd_pcm_substream *substream,
+			       struct snd_soc_dai *dai)
+{
+	int err;
+	struct xlnx_dprx_audio_data *adata;
+	unsigned long jiffies = msecs_to_jiffies(XDP_AUDIO_DETECT_TIMEOUT);
+	struct xdprxss_state *xdprxss = dev_get_drvdata(dai->dev);
+
+	adata = xdprxss->rx_audio_data;
+
+	xdprxss_clr(xdprxss, XDPRX_AUDIO_CONTROL, XDPRX_AUDIO_EN_MASK);
+	xdprxss_set(xdprxss, XDPRX_AUDIO_CONTROL, XDPRX_AUDIO_EN_MASK);
+
+	/*
+	 * TODO: Currently the audio infoframe packet interrupts are not
+	 * coming for the first time without the below msleep.
+	 * Need to find out the root cause and should remove this msleep
+	 */
+	msleep(50);
+
+	/* Enable DP Rx audio and interruts */
+	xdprxss_set(xdprxss, XDPRX_INTR_MASK_REG, XDPRX_INTR_AUDIO_MASK);
+
+	err = wait_event_interruptible_timeout(adata->audio_update_q,
+					       adata->audio_detected,
+					       jiffies);
+	if (!err) {
+		dev_err(dai->dev, "No audio detected in input stream\n");
+		return -EIO;
+	}
+
+	dev_info(dai->dev, "Detected audio, starting capture\n");
+
+	return 0;
+}
+
+/**
+ * xlnx_rx_pcm_shutdown - Deinitialze audio when audio usecase is stopped
+ *
+ * @substream: Pointer to sound pcm substream structure
+ * @dai: Pointer to sound soc dai structure
+ *
+ * This function is called by ALSA framework before audio capture usecase
+ * ends.
+ */
+static void xlnx_rx_pcm_shutdown(struct snd_pcm_substream *substream,
+				 struct snd_soc_dai *dai)
+{
+	struct xdprxss_state *xdprxss = dev_get_drvdata(dai->dev);
+
+	xdprxss_clr(xdprxss, XDPRX_AUDIO_CONTROL, XDPRX_AUDIO_EN_MASK);
+	xdprxss_clr(xdprxss, XDPRX_INTR_MASK_REG, XDPRX_INTR_AUDIO_MASK);
+}
+
+static const struct snd_soc_dai_ops xlnx_rx_dai_ops = {
+	.startup = xlnx_rx_pcm_startup,
+	.shutdown = xlnx_rx_pcm_shutdown,
+};
+
+static struct snd_soc_dai_driver xlnx_rx_audio_dai = {
+	.name = "xlnx_dp_rx",
+	.capture = {
+		.stream_name = "Capture",
+		.channels_min = 2,
+		.channels_max = 8,
+		.rates = SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 |
+			 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 |
+			 SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_176400 |
+			 SNDRV_PCM_RATE_192000,
+		.formats = SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE,
+	},
+	.ops = &xlnx_rx_dai_ops,
+};
+
+static const struct snd_soc_component_driver xlnx_rx_dummy_codec_driver;
+
+/**
+ * dprx_register_aud_dev - register audio device
+ *
+ * @dev: Pointer to Platform structure
+ *
+ * This function registers codec DAI device as part of
+ * ALSA SoC framework.
+ *
+ * Return: 0 on success, error value otherwise
+ */
+static int dprx_register_aud_dev(struct device *dev)
+{
+	return snd_soc_register_component(dev, &xlnx_rx_dummy_codec_driver,
+			&xlnx_rx_audio_dai, 1);
+}
+
+/**
+ * dprx_unregister_aud_dev - register audio device
+ *
+ * @dev: Pointer to Platform structure
+ *
+ * This functions unregisters codec DAI device
+ */
+static void dprx_unregister_aud_dev(struct device *dev)
+{
+	snd_soc_unregister_component(dev);
+}
+
+/* ----------------------------------------------------------------
+ * Platform Device Driver
+ */
+static int xdprxss_parse_of(struct xdprxss_state *xdprxss)
+{
+	struct device_node *node = xdprxss->dev->of_node;
+	u32 val = 0;
+	int ret;
+
+	ret = of_property_read_u32(node, "xlnx,bpc", &xdprxss->bpc);
+	if (ret < 0) {
+		if (ret != -EINVAL) {
+			dev_err(xdprxss->dev, "failed to get xlnx,bpp\n");
+			return ret;
+		}
+	}
+	/*
+	 * TODO : For now driver supports only 8, 10 bpc.
+	 * In future, driver may add with other bpc support
+	 */
+	if (xdprxss->bpc != 8 && xdprxss->bpc != 10) {
+		dev_err(xdprxss->dev, "unsupported bpc = %u\n", xdprxss->bpc);
+		return -EINVAL;
+	}
+
+	xdprxss->hdcp_enable = of_property_read_bool(node, "xlnx,hdcp-enable");
+	/* TODO : This driver does not support HDCP feature */
+	if (xdprxss->hdcp_enable) {
+		dev_err(xdprxss->dev, "hdcp unsupported\n");
+		return -EINVAL;
+	}
+
+	xdprxss->audio_enable = of_property_read_bool(node,
+						      "xlnx,audio-enable");
+	if (!xdprxss->audio_enable)
+		dev_info(xdprxss->dev, "audio not enabled\n");
+
+	xdprxss->versal_gt_present =
+		of_property_read_bool(node, "xlnx,versal-gt");
+
+	ret = of_property_read_u32(node, "xlnx,link-rate", &val);
+	if (ret < 0) {
+		dev_err(xdprxss->dev, "xlnx,link-rate property not found\n");
+		return ret;
+	}
+	if (!(val == DP_LINK_BW_1_62 ||
+	      val == DP_LINK_BW_2_7 ||
+	      val == DP_LINK_BW_5_4 ||
+	      val == DP_LINK_BW_8_1)) {
+		dev_err(xdprxss->dev, "invalid link rate\n");
+		return -EINVAL;
+	}
+	xdprxss->max_linkrate = val;
+
+	ret = of_property_read_u32(node, "xlnx,lane-count", &val);
+	if (ret < 0) {
+		dev_err(xdprxss->dev, "xlnx,lane-count property not found\n");
+		return ret;
+	}
+	if (val < 1 && val > 4) {
+		dev_err(xdprxss->dev, "invalid lane count\n");
+		return -EINVAL;
+	}
+	xdprxss->max_lanecount = val;
+
+	ret = of_property_read_u32(node, "xlnx,mode", &val);
+	if (ret < 0) {
+		dev_err(xdprxss->dev, "xlnx,mode property not found\n");
+		return ret;
+	}
+	if (val > 0) {
+		dev_err(xdprxss->dev, "driver does't support MST mode\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void xlnx_dp_tp1_work_func(struct work_struct *work)
+{
+	struct xdprxss_state *dp;
+
+	dp = container_of(work, struct xdprxss_state, tp1_work.work);
+
+	xdprxss_irq_tp1(dp);
+}
+
+static void xlnx_dp_unplug_work_func(struct work_struct *work)
+{
+	struct xdprxss_state *dp;
+
+	dp = container_of(work, struct xdprxss_state, unplug_work.work);
+
+	xdprxss_irq_unplug(dp);
+}
+
+static int xlnx_find_device(struct platform_device *pdev,
+			    struct xdprxss_state *xdprxss, const char *name)
+{
+	struct device_node *pnode = pdev->dev.of_node;
+	struct device_node *fnode;
+	struct platform_device *iface_pdev;
+
+	fnode = of_parse_phandle(pnode, name, 0);
+	if (!fnode) {
+		dev_err(&pdev->dev, "platform node %s not found\n", name);
+		of_node_put(fnode);
+	} else {
+		iface_pdev = of_find_device_by_node(fnode);
+		if (!iface_pdev) {
+			of_node_put(pnode);
+			return -ENODEV;
+		}
+
+		xdprxss->prvdata = dev_get_drvdata(&iface_pdev->dev);
+		if (!xdprxss->prvdata) {
+			dev_info(&pdev->dev,
+				 "platform device(%s) not found -EPROBE_DEFER\n", name);
+			of_node_put(fnode);
+			return -EPROBE_DEFER;
+		}
+		of_node_put(fnode);
+	}
+
+	return 0;
+}
+
+static int xdprxss_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xdprxss_state *xdprxss;
+	struct device_node *node;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int ret, irq;
+	unsigned int i = 0, j;
+	struct xlnx_dprx_audio_data *adata;
+
+	xdprxss = devm_kzalloc(dev, sizeof(*xdprxss), GFP_KERNEL);
+	if (!xdprxss)
+		return -ENOMEM;
+
+	xdprxss->dev = &pdev->dev;
+	node = xdprxss->dev->of_node;
+
+	ret = xlnx_find_device(pdev, xdprxss, "xlnx,dp-retimer");
+	if (ret)
+		return ret;
+	xdprxss->retimer_prvdata = xdprxss->prvdata;
+
+	ret = xlnx_find_device(pdev, xdprxss, "xlnx,vidphy");
+	if (ret)
+		return ret;
+	xdprxss->vidphy_prvdata = xdprxss->prvdata;
+
+	xdprxss->rx_audio_data =
+		devm_kzalloc(&pdev->dev, sizeof(struct xlnx_dprx_audio_data),
+			     GFP_KERNEL);
+	if (!xdprxss->rx_audio_data)
+		return -ENOMEM;
+
+	adata = xdprxss->rx_audio_data;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dp_base");
+	xdprxss->dp_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(xdprxss->dp_base)) {
+		dev_err(dev, "couldn't map DisplayPort registers\n");
+		return -ENODEV;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "edid_base");
+	xdprxss->edid_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(xdprxss->edid_base)) {
+		dev_err(dev, "Couldn't map EDID IP memory\n");
+		return -ENOENT;
+	}
+
+	xdprxss->axi_clk = devm_clk_get(dev, "s_axi_aclk");
+	if (IS_ERR(xdprxss->axi_clk)) {
+		ret = PTR_ERR(xdprxss->axi_clk);
+		dev_err(&pdev->dev, "failed to get s_axi_clk (%d)\n", ret);
+		return ret;
+	}
+
+	xdprxss->rx_lnk_clk = devm_clk_get(dev, "rx_lnk_clk");
+	if (IS_ERR(xdprxss->rx_lnk_clk)) {
+		ret = PTR_ERR(xdprxss->rx_lnk_clk);
+		dev_err(&pdev->dev, "failed to get rx_lnk_clk (%d)\n", ret);
+		return ret;
+	}
+
+	xdprxss->rx_vid_clk = devm_clk_get(dev, "rx_vid_clk");
+	if (IS_ERR(xdprxss->rx_vid_clk)) {
+		ret = PTR_ERR(xdprxss->rx_vid_clk);
+		dev_err(&pdev->dev, "failed to get rx_vid_clk (%d)\n", ret);
+		return ret;
+	}
+
+	ret = xdprxss_parse_of(xdprxss);
+	if (ret < 0)
+		goto clk_err;
+
+	if (!xdprxss->versal_gt_present) {
+		/* acquire vphy lanes */
+		for (i = 0; i < xdprxss->max_lanecount; i++) {
+			char phy_name[16];
+
+			snprintf(phy_name, sizeof(phy_name), "dp-phy%d", i);
+			xdprxss->phy[i] = devm_phy_get(xdprxss->dev, phy_name);
+			if (IS_ERR(xdprxss->phy[i])) {
+				ret = PTR_ERR(xdprxss->phy[i]);
+				xdprxss->phy[i] = NULL;
+				if (ret == -EPROBE_DEFER)
+					dev_info(dev, "phy not ready -EPROBE_DEFER\n");
+				else
+					dev_err(dev,
+						"failed to get phy lane %s i %d, ret = %d\n",
+						phy_name, i, ret);
+				goto error_phy;
+			}
+			ret = phy_init(xdprxss->phy[i]);
+			if (ret) {
+				dev_err(dev,
+					"failed to init phy lane %d\n", i);
+				goto error_phy;
+			}
+		}
+	} else {
+		xdprxss->phy[0] = devm_phy_get(xdprxss->dev, "dp-gtquad");
+		if (IS_ERR(xdprxss->phy[0]))
+			return dev_err_probe(dev, PTR_ERR(xdprxss->phy[0]),
+					"failed to get phy\n");
+
+		ret = phy_init(xdprxss->phy[0]);
+		if (ret) {
+			dev_err(dev, "failed to init phy\n");
+			goto error_phy;
+		}
+
+		ret = xlnx_find_device(pdev, xdprxss, "xlnx,xilinx-vfmc");
+		if (ret)
+			return ret;
+
+		ret = xlnx_dp_rx_gt_control_init(xdprxss);
+		if (ret < 0)
+			return ret;
+
+		if (get_rx_dec_clk_lock(xdprxss))
+			dev_info(dev, "rx decryption clock failed to lock\n");
+	}
+
+	ret = clk_prepare_enable(xdprxss->axi_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable axi_clk (%d)\n", ret);
+		goto error_phy;
+	}
+
+	ret = clk_prepare_enable(xdprxss->rx_lnk_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable rx_lnk_clk (%d)\n", ret);
+		goto rx_lnk_clk_err;
+	}
+
+	ret = clk_prepare_enable(xdprxss->rx_vid_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable rx_vid_clk (%d)\n", ret);
+		goto rx_vid_clk_err;
+	}
+
+	spin_lock_init(&xdprxss->lock);
+
+	/* Initialize the DP core */
+	xdprxss_core_init(xdprxss);
+
+	/* Initialize V4L2 subdevice and media entity */
+	xdprxss->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xdprxss->subdev;
+	v4l2_subdev_init(subdev, &xdprxss_ops);
+	subdev->dev = &pdev->dev;
+	strscpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+
+	subdev->flags = V4L2_SUBDEV_FL_HAS_EVENTS | V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	subdev->entity.ops = &xdprxss_media_ops;
+
+	v4l2_set_subdevdata(subdev, xdprxss);
+	ret = media_entity_pads_init(&subdev->entity, 1, &xdprxss->pad);
+	if (ret < 0)
+		goto error;
+
+	/* Register interrupt handler */
+	irq = irq_of_parse_and_map(node, 0);
+	ret = devm_request_irq(xdprxss->dev, irq, xdprxss_irq_handler,
+			       IRQF_SHARED, subdev->name, xdprxss);
+	if (ret) {
+		dev_err(dev, "Err = %d Interrupt handler reg failed!\n",
+			ret);
+		goto error;
+	}
+
+	platform_set_drvdata(pdev, xdprxss);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	if (xdprxss->audio_enable) {
+		ret = dprx_register_aud_dev(xdprxss->dev);
+		if (ret < 0) {
+			xdprxss->audio_init = false;
+			dev_err(xdprxss->dev, "dp rx audio init failed\n");
+			goto error;
+		} else {
+			xdprxss->audio_init = true;
+			init_waitqueue_head(&adata->audio_update_q);
+			dev_info(xdprxss->dev, "dp rx audio initialized\n");
+		}
+	}
+
+	INIT_DELAYED_WORK(&xdprxss->tp1_work, xlnx_dp_tp1_work_func);
+	INIT_DELAYED_WORK(&xdprxss->unplug_work, xlnx_dp_unplug_work_func);
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+clk_err:
+	clk_disable_unprepare(xdprxss->rx_vid_clk);
+rx_vid_clk_err:
+	clk_disable_unprepare(xdprxss->rx_lnk_clk);
+rx_lnk_clk_err:
+	clk_disable_unprepare(xdprxss->axi_clk);
+error_phy:
+	dev_dbg(dev, " %s error_phy:\n", __func__);
+	/* release the lanes that we did get, if we did not get all lanes */
+	if (!xdprxss->versal_gt_present) {
+		for (j = 0; j < i; j++) {
+			if (xdprxss->phy[j]) {
+				dev_dbg(dev,
+					"phy_exit() xdprxss->phy[%d] = %p\n",
+					j, xdprxss->phy[j]);
+				phy_exit(xdprxss->phy[j]);
+			}
+		}
+	} else {
+		phy_exit(xdprxss->phy[0]);
+	}
+
+	return ret;
+}
+
+static int xdprxss_remove(struct platform_device *pdev)
+{
+	struct xdprxss_state *xdprxss = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xdprxss->subdev;
+	unsigned int i;
+
+	cancel_delayed_work_sync(&xdprxss->tp1_work);
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+	clk_disable_unprepare(xdprxss->rx_vid_clk);
+	clk_disable_unprepare(xdprxss->rx_lnk_clk);
+	clk_disable_unprepare(xdprxss->axi_clk);
+	if (!xdprxss->versal_gt_present)
+		for (i = 0; i < XDPRX_MAX_LANE_COUNT; i++)
+			phy_exit(xdprxss->phy[i]);
+	else
+		phy_exit(xdprxss->phy[0]);
+
+	if (xdprxss->audio_init)
+		dprx_unregister_aud_dev(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id xdprxss_of_id_table[] = {
+	{ .compatible = "xlnx,v-dp-rxss-3.0", },
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xdprxss_of_id_table);
+
+static struct platform_driver xdprxss_driver = {
+	.driver = {
+		.name		= "xilinx-dprxss",
+		.of_match_table	= xdprxss_of_id_table,
+	},
+	.probe			= xdprxss_probe,
+	.remove			= xdprxss_remove,
+};
+
+module_platform_driver(xdprxss_driver);
+
+MODULE_AUTHOR("Rajesh Gugulothu <gugulothu.rajesh@xilinx.com");
+MODULE_DESCRIPTION("Xilinx DP Rx Subsystem Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-gamma-coeff.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-gamma-coeff.h
@@ -0,0 +1,5385 @@
+/*
+ * Xilinx Gamma Correction IP
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __XILINX_GAMMA_COEFF_H__
+#define __XILINX_GAMMA_COEFF_H__
+
+#define GAMMA_CURVE_LENGTH	(40)
+
+#define GAMMA_BPC_8			(8)
+#define GAMMA8_TABLE_LENGTH		BIT(GAMMA_BPC_8)
+static const u16 xgamma8_01[GAMMA8_TABLE_LENGTH] = {
+	0, 147, 157, 164, 168, 172, 175, 178,
+	180, 183, 184, 186, 188, 189, 191, 192,
+	193, 195, 196, 197, 198, 199, 200, 200,
+	201, 202, 203, 204, 204, 205, 206, 207,
+	207, 208, 208, 209, 210, 210, 211, 211,
+	212, 212, 213, 213, 214, 214, 215, 215,
+	216, 216, 217, 217, 218, 218, 218, 219,
+	219, 220, 220, 220, 221, 221, 221, 222,
+	222, 222, 223, 223, 223, 224, 224, 224,
+	225, 225, 225, 226, 226, 226, 227, 227,
+	227, 227, 228, 228, 228, 228, 229, 229,
+	229, 230, 230, 230, 230, 231, 231, 231,
+	231, 232, 232, 232, 232, 232, 233, 233,
+	233, 233, 234, 234, 234, 234, 234, 235,
+	235, 235, 235, 235, 236, 236, 236, 236,
+	236, 237, 237, 237, 237, 237, 238, 238,
+	238, 238, 238, 239, 239, 239, 239, 239,
+	239, 240, 240, 240, 240, 240, 240, 241,
+	241, 241, 241, 241, 241, 242, 242, 242,
+	242, 242, 242, 243, 243, 243, 243, 243,
+	243, 244, 244, 244, 244, 244, 244, 244,
+	245, 245, 245, 245, 245, 245, 245, 246,
+	246, 246, 246, 246, 246, 246, 247, 247,
+	247, 247, 247, 247, 247, 247, 248, 248,
+	248, 248, 248, 248, 248, 249, 249, 249,
+	249, 249, 249, 249, 249, 249, 250, 250,
+	250, 250, 250, 250, 250, 250, 251, 251,
+	251, 251, 251, 251, 251, 251, 251, 252,
+	252, 252, 252, 252, 252, 252, 252, 252,
+	253, 253, 253, 253, 253, 253, 253, 253,
+	253, 254, 254, 254, 254, 254, 254, 254,
+	254, 254, 254, 255, 255, 255, 255, 255,
+};
+
+static const u16 xgamma8_02[GAMMA8_TABLE_LENGTH] = {
+	0, 84, 97, 105, 111, 116, 120, 124,
+	128, 131, 133, 136, 138, 141, 143, 145,
+	147, 148, 150, 152, 153, 155, 156, 158,
+	159, 160, 162, 163, 164, 165, 166, 167,
+	168, 169, 170, 171, 172, 173, 174, 175,
+	176, 177, 178, 179, 179, 180, 181, 182,
+	183, 183, 184, 185, 186, 186, 187, 188,
+	188, 189, 190, 190, 191, 192, 192, 193,
+	193, 194, 195, 195, 196, 196, 197, 197,
+	198, 199, 199, 200, 200, 201, 201, 202,
+	202, 203, 203, 204, 204, 205, 205, 206,
+	206, 207, 207, 208, 208, 208, 209, 209,
+	210, 210, 211, 211, 211, 212, 212, 213,
+	213, 214, 214, 214, 215, 215, 216, 216,
+	216, 217, 217, 217, 218, 218, 219, 219,
+	219, 220, 220, 220, 221, 221, 221, 222,
+	222, 223, 223, 223, 224, 224, 224, 225,
+	225, 225, 226, 226, 226, 227, 227, 227,
+	227, 228, 228, 228, 229, 229, 229, 230,
+	230, 230, 231, 231, 231, 231, 232, 232,
+	232, 233, 233, 233, 233, 234, 234, 234,
+	235, 235, 235, 235, 236, 236, 236, 237,
+	237, 237, 237, 238, 238, 238, 238, 239,
+	239, 239, 239, 240, 240, 240, 240, 241,
+	241, 241, 241, 242, 242, 242, 242, 243,
+	243, 243, 243, 244, 244, 244, 244, 245,
+	245, 245, 245, 246, 246, 246, 246, 246,
+	247, 247, 247, 247, 248, 248, 248, 248,
+	248, 249, 249, 249, 249, 250, 250, 250,
+	250, 250, 251, 251, 251, 251, 252, 252,
+	252, 252, 252, 253, 253, 253, 253, 253,
+	254, 254, 254, 254, 254, 255, 255, 255,
+};
+
+static const u16 xgamma8_03[GAMMA8_TABLE_LENGTH] = {
+	0, 48, 60, 67, 73, 78, 83, 87,
+	90, 94, 97, 99, 102, 104, 107, 109,
+	111, 113, 115, 117, 119, 121, 122, 124,
+	125, 127, 129, 130, 131, 133, 134, 136,
+	137, 138, 139, 141, 142, 143, 144, 145,
+	146, 147, 148, 149, 151, 152, 153, 154,
+	155, 155, 156, 157, 158, 159, 160, 161,
+	162, 163, 164, 164, 165, 166, 167, 168,
+	168, 169, 170, 171, 172, 172, 173, 174,
+	174, 175, 176, 177, 177, 178, 179, 179,
+	180, 181, 181, 182, 183, 183, 184, 185,
+	185, 186, 187, 187, 188, 188, 189, 190,
+	190, 191, 191, 192, 193, 193, 194, 194,
+	195, 195, 196, 197, 197, 198, 198, 199,
+	199, 200, 200, 201, 201, 202, 202, 203,
+	203, 204, 204, 205, 205, 206, 206, 207,
+	207, 208, 208, 209, 209, 210, 210, 211,
+	211, 212, 212, 213, 213, 213, 214, 214,
+	215, 215, 216, 216, 217, 217, 217, 218,
+	218, 219, 219, 220, 220, 220, 221, 221,
+	222, 222, 223, 223, 223, 224, 224, 225,
+	225, 225, 226, 226, 227, 227, 227, 228,
+	228, 229, 229, 229, 230, 230, 230, 231,
+	231, 232, 232, 232, 233, 233, 233, 234,
+	234, 235, 235, 235, 236, 236, 236, 237,
+	237, 237, 238, 238, 238, 239, 239, 240,
+	240, 240, 241, 241, 241, 242, 242, 242,
+	243, 243, 243, 244, 244, 244, 245, 245,
+	245, 246, 246, 246, 247, 247, 247, 248,
+	248, 248, 249, 249, 249, 249, 250, 250,
+	250, 251, 251, 251, 252, 252, 252, 253,
+	253, 253, 253, 254, 254, 254, 255, 255,
+};
+
+static const u16 xgamma8_04[GAMMA8_TABLE_LENGTH] = {
+	0, 28, 37, 43, 48, 53, 57, 61,
+	64, 67, 70, 73, 75, 78, 80, 82,
+	84, 86, 88, 90, 92, 94, 96, 97,
+	99, 101, 102, 104, 105, 107, 108, 110,
+	111, 113, 114, 115, 117, 118, 119, 120,
+	122, 123, 124, 125, 126, 127, 129, 130,
+	131, 132, 133, 134, 135, 136, 137, 138,
+	139, 140, 141, 142, 143, 144, 145, 146,
+	147, 148, 149, 149, 150, 151, 152, 153,
+	154, 155, 155, 156, 157, 158, 159, 160,
+	160, 161, 162, 163, 164, 164, 165, 166,
+	167, 167, 168, 169, 170, 170, 171, 172,
+	173, 173, 174, 175, 175, 176, 177, 177,
+	178, 179, 179, 180, 181, 182, 182, 183,
+	183, 184, 185, 185, 186, 187, 187, 188,
+	189, 189, 190, 190, 191, 192, 192, 193,
+	194, 194, 195, 195, 196, 197, 197, 198,
+	198, 199, 199, 200, 201, 201, 202, 202,
+	203, 203, 204, 205, 205, 206, 206, 207,
+	207, 208, 208, 209, 209, 210, 211, 211,
+	212, 212, 213, 213, 214, 214, 215, 215,
+	216, 216, 217, 217, 218, 218, 219, 219,
+	220, 220, 221, 221, 222, 222, 223, 223,
+	224, 224, 225, 225, 226, 226, 227, 227,
+	228, 228, 229, 229, 230, 230, 230, 231,
+	231, 232, 232, 233, 233, 234, 234, 235,
+	235, 235, 236, 236, 237, 237, 238, 238,
+	239, 239, 240, 240, 240, 241, 241, 242,
+	242, 243, 243, 243, 244, 244, 245, 245,
+	246, 246, 246, 247, 247, 248, 248, 248,
+	249, 249, 250, 250, 251, 251, 251, 252,
+	252, 253, 253, 253, 254, 254, 255, 255,
+};
+
+static const u16 xgamma8_05[GAMMA8_TABLE_LENGTH] = {
+	0, 16, 23, 28, 32, 36, 39, 42,
+	45, 48, 50, 53, 55, 58, 60, 62,
+	64, 66, 68, 70, 71, 73, 75, 77,
+	78, 80, 81, 83, 84, 86, 87, 89,
+	90, 92, 93, 94, 96, 97, 98, 100,
+	101, 102, 103, 105, 106, 107, 108, 109,
+	111, 112, 113, 114, 115, 116, 117, 118,
+	119, 121, 122, 123, 124, 125, 126, 127,
+	128, 129, 130, 131, 132, 133, 134, 135,
+	135, 136, 137, 138, 139, 140, 141, 142,
+	143, 144, 145, 145, 146, 147, 148, 149,
+	150, 151, 151, 152, 153, 154, 155, 156,
+	156, 157, 158, 159, 160, 160, 161, 162,
+	163, 164, 164, 165, 166, 167, 167, 168,
+	169, 170, 170, 171, 172, 173, 173, 174,
+	175, 176, 176, 177, 178, 179, 179, 180,
+	181, 181, 182, 183, 183, 184, 185, 186,
+	186, 187, 188, 188, 189, 190, 190, 191,
+	192, 192, 193, 194, 194, 195, 196, 196,
+	197, 198, 198, 199, 199, 200, 201, 201,
+	202, 203, 203, 204, 204, 205, 206, 206,
+	207, 208, 208, 209, 209, 210, 211, 211,
+	212, 212, 213, 214, 214, 215, 215, 216,
+	217, 217, 218, 218, 219, 220, 220, 221,
+	221, 222, 222, 223, 224, 224, 225, 225,
+	226, 226, 227, 228, 228, 229, 229, 230,
+	230, 231, 231, 232, 233, 233, 234, 234,
+	235, 235, 236, 236, 237, 237, 238, 238,
+	239, 240, 240, 241, 241, 242, 242, 243,
+	243, 244, 244, 245, 245, 246, 246, 247,
+	247, 248, 248, 249, 249, 250, 250, 251,
+	251, 252, 252, 253, 253, 254, 254, 255,
+};
+
+static const u16 xgamma8_06[GAMMA8_TABLE_LENGTH] = {
+	0, 9, 14, 18, 21, 24, 27, 29,
+	32, 34, 37, 39, 41, 43, 45, 47,
+	48, 50, 52, 54, 55, 57, 59, 60,
+	62, 63, 65, 66, 68, 69, 71, 72,
+	73, 75, 76, 77, 79, 80, 81, 83,
+	84, 85, 86, 88, 89, 90, 91, 92,
+	94, 95, 96, 97, 98, 99, 100, 102,
+	103, 104, 105, 106, 107, 108, 109, 110,
+	111, 112, 113, 114, 115, 116, 117, 118,
+	119, 120, 121, 122, 123, 124, 125, 126,
+	127, 128, 129, 130, 131, 132, 133, 134,
+	135, 136, 137, 137, 138, 139, 140, 141,
+	142, 143, 144, 145, 145, 146, 147, 148,
+	149, 150, 151, 151, 152, 153, 154, 155,
+	156, 156, 157, 158, 159, 160, 161, 161,
+	162, 163, 164, 165, 165, 166, 167, 168,
+	169, 169, 170, 171, 172, 173, 173, 174,
+	175, 176, 176, 177, 178, 179, 179, 180,
+	181, 182, 182, 183, 184, 185, 185, 186,
+	187, 188, 188, 189, 190, 191, 191, 192,
+	193, 194, 194, 195, 196, 196, 197, 198,
+	199, 199, 200, 201, 201, 202, 203, 203,
+	204, 205, 206, 206, 207, 208, 208, 209,
+	210, 210, 211, 212, 212, 213, 214, 214,
+	215, 216, 216, 217, 218, 218, 219, 220,
+	220, 221, 222, 222, 223, 224, 224, 225,
+	226, 226, 227, 228, 228, 229, 230, 230,
+	231, 231, 232, 233, 233, 234, 235, 235,
+	236, 237, 237, 238, 238, 239, 240, 240,
+	241, 242, 242, 243, 243, 244, 245, 245,
+	246, 247, 247, 248, 248, 249, 250, 250,
+	251, 251, 252, 253, 253, 254, 254, 255,
+};
+
+static const u16 xgamma8_07[GAMMA8_TABLE_LENGTH] = {
+	0, 5, 9, 11, 14, 16, 18, 21,
+	23, 25, 26, 28, 30, 32, 33, 35,
+	37, 38, 40, 41, 43, 44, 46, 47,
+	49, 50, 52, 53, 54, 56, 57, 58,
+	60, 61, 62, 64, 65, 66, 67, 69,
+	70, 71, 72, 73, 75, 76, 77, 78,
+	79, 80, 82, 83, 84, 85, 86, 87,
+	88, 89, 90, 92, 93, 94, 95, 96,
+	97, 98, 99, 100, 101, 102, 103, 104,
+	105, 106, 107, 108, 109, 110, 111, 112,
+	113, 114, 115, 116, 117, 118, 119, 120,
+	121, 122, 123, 124, 125, 126, 127, 128,
+	129, 130, 131, 131, 132, 133, 134, 135,
+	136, 137, 138, 139, 140, 141, 142, 142,
+	143, 144, 145, 146, 147, 148, 149, 150,
+	150, 151, 152, 153, 154, 155, 156, 157,
+	157, 158, 159, 160, 161, 162, 163, 163,
+	164, 165, 166, 167, 168, 168, 169, 170,
+	171, 172, 173, 173, 174, 175, 176, 177,
+	178, 178, 179, 180, 181, 182, 182, 183,
+	184, 185, 186, 186, 187, 188, 189, 190,
+	190, 191, 192, 193, 194, 194, 195, 196,
+	197, 197, 198, 199, 200, 201, 201, 202,
+	203, 204, 204, 205, 206, 207, 208, 208,
+	209, 210, 211, 211, 212, 213, 214, 214,
+	215, 216, 217, 217, 218, 219, 220, 220,
+	221, 222, 223, 223, 224, 225, 226, 226,
+	227, 228, 228, 229, 230, 231, 231, 232,
+	233, 234, 234, 235, 236, 237, 237, 238,
+	239, 239, 240, 241, 242, 242, 243, 244,
+	244, 245, 246, 247, 247, 248, 249, 249,
+	250, 251, 251, 252, 253, 254, 254, 255,
+};
+
+static const u16 xgamma8_08[GAMMA8_TABLE_LENGTH] = {
+	0, 3, 5, 7, 9, 11, 13, 14,
+	16, 18, 19, 21, 22, 24, 25, 26,
+	28, 29, 31, 32, 33, 35, 36, 37,
+	39, 40, 41, 42, 44, 45, 46, 47,
+	48, 50, 51, 52, 53, 54, 56, 57,
+	58, 59, 60, 61, 63, 64, 65, 66,
+	67, 68, 69, 70, 71, 73, 74, 75,
+	76, 77, 78, 79, 80, 81, 82, 83,
+	84, 85, 86, 88, 89, 90, 91, 92,
+	93, 94, 95, 96, 97, 98, 99, 100,
+	101, 102, 103, 104, 105, 106, 107, 108,
+	109, 110, 111, 112, 113, 114, 115, 116,
+	117, 118, 119, 120, 121, 122, 123, 123,
+	124, 125, 126, 127, 128, 129, 130, 131,
+	132, 133, 134, 135, 136, 137, 138, 139,
+	140, 140, 141, 142, 143, 144, 145, 146,
+	147, 148, 149, 150, 151, 151, 152, 153,
+	154, 155, 156, 157, 158, 159, 160, 161,
+	161, 162, 163, 164, 165, 166, 167, 168,
+	169, 169, 170, 171, 172, 173, 174, 175,
+	176, 177, 177, 178, 179, 180, 181, 182,
+	183, 183, 184, 185, 186, 187, 188, 189,
+	190, 190, 191, 192, 193, 194, 195, 196,
+	196, 197, 198, 199, 200, 201, 202, 202,
+	203, 204, 205, 206, 207, 207, 208, 209,
+	210, 211, 212, 212, 213, 214, 215, 216,
+	217, 217, 218, 219, 220, 221, 222, 222,
+	223, 224, 225, 226, 227, 227, 228, 229,
+	230, 231, 232, 232, 233, 234, 235, 236,
+	236, 237, 238, 239, 240, 240, 241, 242,
+	243, 244, 245, 245, 246, 247, 248, 249,
+	249, 250, 251, 252, 253, 253, 254, 255,
+};
+
+static const u16 xgamma8_09[GAMMA8_TABLE_LENGTH] = {
+	0, 2, 3, 5, 6, 7, 9, 10,
+	11, 13, 14, 15, 16, 18, 19, 20,
+	21, 22, 23, 25, 26, 27, 28, 29,
+	30, 32, 33, 34, 35, 36, 37, 38,
+	39, 40, 42, 43, 44, 45, 46, 47,
+	48, 49, 50, 51, 52, 54, 55, 56,
+	57, 58, 59, 60, 61, 62, 63, 64,
+	65, 66, 67, 68, 69, 70, 71, 72,
+	73, 75, 76, 77, 78, 79, 80, 81,
+	82, 83, 84, 85, 86, 87, 88, 89,
+	90, 91, 92, 93, 94, 95, 96, 97,
+	98, 99, 100, 101, 102, 103, 104, 105,
+	106, 107, 108, 109, 110, 111, 112, 113,
+	114, 115, 116, 117, 118, 119, 120, 121,
+	122, 123, 124, 125, 126, 126, 127, 128,
+	129, 130, 131, 132, 133, 134, 135, 136,
+	137, 138, 139, 140, 141, 142, 143, 144,
+	145, 146, 147, 148, 149, 150, 151, 152,
+	152, 153, 154, 155, 156, 157, 158, 159,
+	160, 161, 162, 163, 164, 165, 166, 167,
+	168, 169, 170, 170, 171, 172, 173, 174,
+	175, 176, 177, 178, 179, 180, 181, 182,
+	183, 184, 185, 185, 186, 187, 188, 189,
+	190, 191, 192, 193, 194, 195, 196, 197,
+	198, 198, 199, 200, 201, 202, 203, 204,
+	205, 206, 207, 208, 209, 210, 210, 211,
+	212, 213, 214, 215, 216, 217, 218, 219,
+	220, 221, 221, 222, 223, 224, 225, 226,
+	227, 228, 229, 230, 231, 231, 232, 233,
+	234, 235, 236, 237, 238, 239, 240, 241,
+	241, 242, 243, 244, 245, 246, 247, 248,
+	249, 250, 250, 251, 252, 253, 254, 255,
+};
+
+static const u16 xgamma8_10[GAMMA8_TABLE_LENGTH] = {
+	0, 1, 2, 3, 4, 5, 6, 7,
+	8, 9, 10, 11, 12, 13, 14, 15,
+	16, 17, 18, 19, 20, 21, 22, 23,
+	24, 25, 26, 27, 28, 29, 30, 31,
+	32, 33, 34, 35, 36, 37, 38, 39,
+	40, 41, 42, 43, 44, 45, 46, 47,
+	48, 49, 50, 51, 52, 53, 54, 55,
+	56, 57, 58, 59, 60, 61, 62, 63,
+	64, 65, 66, 67, 68, 69, 70, 71,
+	72, 73, 74, 75, 76, 77, 78, 79,
+	80, 81, 82, 83, 84, 85, 86, 87,
+	88, 89, 90, 91, 92, 93, 94, 95,
+	96, 97, 98, 99, 100, 101, 102, 103,
+	104, 105, 106, 107, 108, 109, 110, 111,
+	112, 113, 114, 115, 116, 117, 118, 119,
+	120, 121, 122, 123, 124, 125, 126, 127,
+	128, 129, 130, 131, 132, 133, 134, 135,
+	136, 137, 138, 139, 140, 141, 142, 143,
+	144, 145, 146, 147, 148, 149, 150, 151,
+	152, 153, 154, 155, 156, 157, 158, 159,
+	160, 161, 162, 163, 164, 165, 166, 167,
+	168, 169, 170, 171, 172, 173, 174, 175,
+	176, 177, 178, 179, 180, 181, 182, 183,
+	184, 185, 186, 187, 188, 189, 190, 191,
+	192, 193, 194, 195, 196, 197, 198, 199,
+	200, 201, 202, 203, 204, 205, 206, 207,
+	208, 209, 210, 211, 212, 213, 214, 215,
+	216, 217, 218, 219, 220, 221, 222, 223,
+	224, 225, 226, 227, 228, 229, 230, 231,
+	232, 233, 234, 235, 236, 237, 238, 239,
+	240, 241, 242, 243, 244, 245, 246, 247,
+	248, 249, 250, 251, 252, 253, 254, 255,
+};
+
+static const u16 xgamma8_11[GAMMA8_TABLE_LENGTH] = {
+	0, 1, 1, 2, 3, 3, 4, 5,
+	6, 6, 7, 8, 9, 10, 10, 11,
+	12, 13, 14, 15, 16, 16, 17, 18,
+	19, 20, 21, 22, 22, 23, 24, 25,
+	26, 27, 28, 29, 30, 31, 31, 32,
+	33, 34, 35, 36, 37, 38, 39, 40,
+	41, 42, 42, 43, 44, 45, 46, 47,
+	48, 49, 50, 51, 52, 53, 54, 55,
+	56, 57, 58, 59, 60, 61, 62, 62,
+	63, 64, 65, 66, 67, 68, 69, 70,
+	71, 72, 73, 74, 75, 76, 77, 78,
+	79, 80, 81, 82, 83, 84, 85, 86,
+	87, 88, 89, 90, 91, 92, 93, 94,
+	95, 96, 97, 98, 99, 100, 101, 102,
+	103, 104, 105, 106, 107, 108, 109, 110,
+	111, 112, 113, 114, 115, 116, 117, 118,
+	119, 121, 122, 123, 124, 125, 126, 127,
+	128, 129, 130, 131, 132, 133, 134, 135,
+	136, 137, 138, 139, 140, 141, 142, 143,
+	144, 145, 146, 147, 149, 150, 151, 152,
+	153, 154, 155, 156, 157, 158, 159, 160,
+	161, 162, 163, 164, 165, 166, 167, 169,
+	170, 171, 172, 173, 174, 175, 176, 177,
+	178, 179, 180, 181, 182, 183, 184, 186,
+	187, 188, 189, 190, 191, 192, 193, 194,
+	195, 196, 197, 198, 199, 201, 202, 203,
+	204, 205, 206, 207, 208, 209, 210, 211,
+	212, 214, 215, 216, 217, 218, 219, 220,
+	221, 222, 223, 224, 225, 227, 228, 229,
+	230, 231, 232, 233, 234, 235, 236, 237,
+	239, 240, 241, 242, 243, 244, 245, 246,
+	247, 248, 250, 251, 252, 253, 254, 255,
+};
+
+static const u16 xgamma8_12[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 1, 1, 2, 2, 3, 3,
+	4, 5, 5, 6, 7, 7, 8, 9,
+	9, 10, 11, 11, 12, 13, 13, 14,
+	15, 16, 16, 17, 18, 19, 20, 20,
+	21, 22, 23, 24, 24, 25, 26, 27,
+	28, 28, 29, 30, 31, 32, 33, 34,
+	34, 35, 36, 37, 38, 39, 40, 40,
+	41, 42, 43, 44, 45, 46, 47, 48,
+	49, 49, 50, 51, 52, 53, 54, 55,
+	56, 57, 58, 59, 60, 61, 62, 62,
+	63, 64, 65, 66, 67, 68, 69, 70,
+	71, 72, 73, 74, 75, 76, 77, 78,
+	79, 80, 81, 82, 83, 84, 85, 86,
+	87, 88, 89, 90, 91, 92, 93, 94,
+	95, 96, 97, 98, 99, 100, 101, 102,
+	103, 104, 105, 106, 107, 108, 109, 110,
+	112, 113, 114, 115, 116, 117, 118, 119,
+	120, 121, 122, 123, 124, 125, 126, 127,
+	128, 130, 131, 132, 133, 134, 135, 136,
+	137, 138, 139, 140, 141, 142, 144, 145,
+	146, 147, 148, 149, 150, 151, 152, 153,
+	155, 156, 157, 158, 159, 160, 161, 162,
+	163, 165, 166, 167, 168, 169, 170, 171,
+	172, 173, 175, 176, 177, 178, 179, 180,
+	181, 183, 184, 185, 186, 187, 188, 189,
+	191, 192, 193, 194, 195, 196, 197, 199,
+	200, 201, 202, 203, 204, 205, 207, 208,
+	209, 210, 211, 212, 214, 215, 216, 217,
+	218, 219, 221, 222, 223, 224, 225, 226,
+	228, 229, 230, 231, 232, 234, 235, 236,
+	237, 238, 239, 241, 242, 243, 244, 245,
+	247, 248, 249, 250, 251, 253, 254, 255,
+};
+
+static const u16 xgamma8_13[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 1, 1, 2, 2, 2,
+	3, 3, 4, 4, 5, 5, 6, 6,
+	7, 8, 8, 9, 9, 10, 11, 11,
+	12, 12, 13, 14, 14, 15, 16, 16,
+	17, 18, 19, 19, 20, 21, 21, 22,
+	23, 24, 24, 25, 26, 27, 28, 28,
+	29, 30, 31, 31, 32, 33, 34, 35,
+	36, 36, 37, 38, 39, 40, 41, 41,
+	42, 43, 44, 45, 46, 47, 47, 48,
+	49, 50, 51, 52, 53, 54, 55, 56,
+	57, 57, 58, 59, 60, 61, 62, 63,
+	64, 65, 66, 67, 68, 69, 70, 71,
+	72, 73, 74, 75, 76, 76, 77, 78,
+	79, 80, 81, 82, 83, 84, 85, 86,
+	88, 89, 90, 91, 92, 93, 94, 95,
+	96, 97, 98, 99, 100, 101, 102, 103,
+	104, 105, 106, 107, 108, 109, 110, 112,
+	113, 114, 115, 116, 117, 118, 119, 120,
+	121, 122, 124, 125, 126, 127, 128, 129,
+	130, 131, 132, 133, 135, 136, 137, 138,
+	139, 140, 141, 143, 144, 145, 146, 147,
+	148, 149, 151, 152, 153, 154, 155, 156,
+	157, 159, 160, 161, 162, 163, 164, 166,
+	167, 168, 169, 170, 172, 173, 174, 175,
+	176, 178, 179, 180, 181, 182, 184, 185,
+	186, 187, 188, 190, 191, 192, 193, 194,
+	196, 197, 198, 199, 201, 202, 203, 204,
+	206, 207, 208, 209, 210, 212, 213, 214,
+	215, 217, 218, 219, 220, 222, 223, 224,
+	226, 227, 228, 229, 231, 232, 233, 234,
+	236, 237, 238, 240, 241, 242, 243, 245,
+	246, 247, 249, 250, 251, 252, 254, 255,
+};
+
+static const u16 xgamma8_14[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 1, 1, 1, 1, 2,
+	2, 2, 3, 3, 4, 4, 4, 5,
+	5, 6, 6, 7, 7, 8, 8, 9,
+	9, 10, 10, 11, 12, 12, 13, 13,
+	14, 15, 15, 16, 16, 17, 18, 18,
+	19, 20, 20, 21, 22, 22, 23, 24,
+	25, 25, 26, 27, 28, 28, 29, 30,
+	31, 31, 32, 33, 34, 34, 35, 36,
+	37, 38, 38, 39, 40, 41, 42, 43,
+	43, 44, 45, 46, 47, 48, 49, 49,
+	50, 51, 52, 53, 54, 55, 56, 57,
+	57, 58, 59, 60, 61, 62, 63, 64,
+	65, 66, 67, 68, 69, 70, 71, 72,
+	73, 74, 75, 76, 77, 78, 79, 80,
+	81, 82, 83, 84, 85, 86, 87, 88,
+	89, 90, 91, 92, 93, 94, 95, 96,
+	97, 98, 99, 100, 101, 103, 104, 105,
+	106, 107, 108, 109, 110, 111, 112, 113,
+	115, 116, 117, 118, 119, 120, 121, 122,
+	124, 125, 126, 127, 128, 129, 130, 132,
+	133, 134, 135, 136, 137, 139, 140, 141,
+	142, 143, 145, 146, 147, 148, 149, 151,
+	152, 153, 154, 155, 157, 158, 159, 160,
+	161, 163, 164, 165, 166, 168, 169, 170,
+	171, 173, 174, 175, 176, 178, 179, 180,
+	181, 183, 184, 185, 187, 188, 189, 190,
+	192, 193, 194, 196, 197, 198, 200, 201,
+	202, 203, 205, 206, 207, 209, 210, 211,
+	213, 214, 215, 217, 218, 219, 221, 222,
+	223, 225, 226, 227, 229, 230, 232, 233,
+	234, 236, 237, 238, 240, 241, 242, 244,
+	245, 247, 248, 249, 251, 252, 254, 255,
+};
+
+static const u16 xgamma8_15[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 1, 1, 1, 1,
+	1, 2, 2, 2, 3, 3, 3, 4,
+	4, 4, 5, 5, 6, 6, 6, 7,
+	7, 8, 8, 9, 9, 10, 10, 11,
+	11, 12, 12, 13, 14, 14, 15, 15,
+	16, 16, 17, 18, 18, 19, 20, 20,
+	21, 21, 22, 23, 23, 24, 25, 26,
+	26, 27, 28, 28, 29, 30, 31, 31,
+	32, 33, 34, 34, 35, 36, 37, 37,
+	38, 39, 40, 41, 41, 42, 43, 44,
+	45, 46, 46, 47, 48, 49, 50, 51,
+	52, 53, 53, 54, 55, 56, 57, 58,
+	59, 60, 61, 62, 63, 64, 65, 65,
+	66, 67, 68, 69, 70, 71, 72, 73,
+	74, 75, 76, 77, 78, 79, 80, 81,
+	82, 83, 84, 85, 86, 88, 89, 90,
+	91, 92, 93, 94, 95, 96, 97, 98,
+	99, 100, 102, 103, 104, 105, 106, 107,
+	108, 109, 110, 112, 113, 114, 115, 116,
+	117, 119, 120, 121, 122, 123, 124, 126,
+	127, 128, 129, 130, 132, 133, 134, 135,
+	136, 138, 139, 140, 141, 142, 144, 145,
+	146, 147, 149, 150, 151, 152, 154, 155,
+	156, 158, 159, 160, 161, 163, 164, 165,
+	167, 168, 169, 171, 172, 173, 174, 176,
+	177, 178, 180, 181, 182, 184, 185, 187,
+	188, 189, 191, 192, 193, 195, 196, 197,
+	199, 200, 202, 203, 204, 206, 207, 209,
+	210, 211, 213, 214, 216, 217, 218, 220,
+	221, 223, 224, 226, 227, 228, 230, 231,
+	233, 234, 236, 237, 239, 240, 242, 243,
+	245, 246, 248, 249, 251, 252, 254, 255,
+};
+
+static const u16 xgamma8_16[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 2, 2, 2, 2, 3,
+	3, 3, 4, 4, 4, 5, 5, 5,
+	6, 6, 7, 7, 7, 8, 8, 9,
+	9, 10, 10, 11, 11, 12, 12, 13,
+	13, 14, 14, 15, 15, 16, 16, 17,
+	18, 18, 19, 19, 20, 21, 21, 22,
+	23, 23, 24, 25, 25, 26, 27, 27,
+	28, 29, 29, 30, 31, 31, 32, 33,
+	34, 34, 35, 36, 37, 38, 38, 39,
+	40, 41, 42, 42, 43, 44, 45, 46,
+	46, 47, 48, 49, 50, 51, 52, 53,
+	53, 54, 55, 56, 57, 58, 59, 60,
+	61, 62, 63, 64, 64, 65, 66, 67,
+	68, 69, 70, 71, 72, 73, 74, 75,
+	76, 77, 78, 79, 80, 81, 83, 84,
+	85, 86, 87, 88, 89, 90, 91, 92,
+	93, 94, 95, 97, 98, 99, 100, 101,
+	102, 103, 104, 106, 107, 108, 109, 110,
+	111, 113, 114, 115, 116, 117, 119, 120,
+	121, 122, 123, 125, 126, 127, 128, 130,
+	131, 132, 133, 135, 136, 137, 138, 140,
+	141, 142, 143, 145, 146, 147, 149, 150,
+	151, 153, 154, 155, 157, 158, 159, 161,
+	162, 163, 165, 166, 167, 169, 170, 171,
+	173, 174, 176, 177, 178, 180, 181, 183,
+	184, 185, 187, 188, 190, 191, 193, 194,
+	196, 197, 198, 200, 201, 203, 204, 206,
+	207, 209, 210, 212, 213, 215, 216, 218,
+	219, 221, 222, 224, 225, 227, 228, 230,
+	231, 233, 235, 236, 238, 239, 241, 242,
+	244, 245, 247, 249, 250, 252, 253, 255,
+};
+
+static const u16 xgamma8_17[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 2, 2, 2,
+	2, 3, 3, 3, 3, 4, 4, 4,
+	5, 5, 5, 6, 6, 6, 7, 7,
+	7, 8, 8, 9, 9, 10, 10, 10,
+	11, 11, 12, 12, 13, 13, 14, 14,
+	15, 15, 16, 17, 17, 18, 18, 19,
+	19, 20, 21, 21, 22, 22, 23, 24,
+	24, 25, 26, 26, 27, 28, 28, 29,
+	30, 30, 31, 32, 33, 33, 34, 35,
+	36, 36, 37, 38, 39, 39, 40, 41,
+	42, 43, 43, 44, 45, 46, 47, 48,
+	48, 49, 50, 51, 52, 53, 54, 55,
+	56, 56, 57, 58, 59, 60, 61, 62,
+	63, 64, 65, 66, 67, 68, 69, 70,
+	71, 72, 73, 74, 75, 76, 77, 78,
+	79, 80, 81, 82, 83, 84, 85, 86,
+	88, 89, 90, 91, 92, 93, 94, 95,
+	97, 98, 99, 100, 101, 102, 103, 105,
+	106, 107, 108, 109, 111, 112, 113, 114,
+	115, 117, 118, 119, 120, 122, 123, 124,
+	125, 127, 128, 129, 131, 132, 133, 134,
+	136, 137, 138, 140, 141, 142, 144, 145,
+	146, 148, 149, 151, 152, 153, 155, 156,
+	157, 159, 160, 162, 163, 164, 166, 167,
+	169, 170, 172, 173, 174, 176, 177, 179,
+	180, 182, 183, 185, 186, 188, 189, 191,
+	192, 194, 195, 197, 198, 200, 201, 203,
+	205, 206, 208, 209, 211, 212, 214, 216,
+	217, 219, 220, 222, 224, 225, 227, 228,
+	230, 232, 233, 235, 237, 238, 240, 242,
+	243, 245, 247, 248, 250, 252, 253, 255,
+};
+
+static const u16 xgamma8_18[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 3, 3, 3, 3,
+	4, 4, 4, 4, 5, 5, 5, 6,
+	6, 6, 7, 7, 8, 8, 8, 9,
+	9, 10, 10, 10, 11, 11, 12, 12,
+	13, 13, 14, 14, 15, 15, 16, 16,
+	17, 17, 18, 18, 19, 19, 20, 21,
+	21, 22, 22, 23, 24, 24, 25, 26,
+	26, 27, 28, 28, 29, 30, 30, 31,
+	32, 32, 33, 34, 35, 35, 36, 37,
+	38, 38, 39, 40, 41, 41, 42, 43,
+	44, 45, 46, 46, 47, 48, 49, 50,
+	51, 52, 53, 53, 54, 55, 56, 57,
+	58, 59, 60, 61, 62, 63, 64, 65,
+	66, 67, 68, 69, 70, 71, 72, 73,
+	74, 75, 76, 77, 78, 79, 80, 81,
+	82, 83, 84, 86, 87, 88, 89, 90,
+	91, 92, 93, 95, 96, 97, 98, 99,
+	100, 102, 103, 104, 105, 107, 108, 109,
+	110, 111, 113, 114, 115, 116, 118, 119,
+	120, 122, 123, 124, 126, 127, 128, 129,
+	131, 132, 134, 135, 136, 138, 139, 140,
+	142, 143, 145, 146, 147, 149, 150, 152,
+	153, 154, 156, 157, 159, 160, 162, 163,
+	165, 166, 168, 169, 171, 172, 174, 175,
+	177, 178, 180, 181, 183, 184, 186, 188,
+	189, 191, 192, 194, 195, 197, 199, 200,
+	202, 204, 205, 207, 208, 210, 212, 213,
+	215, 217, 218, 220, 222, 224, 225, 227,
+	229, 230, 232, 234, 236, 237, 239, 241,
+	243, 244, 246, 248, 250, 251, 253, 255,
+};
+
+static const u16 xgamma8_19[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 1, 1, 1, 1, 1, 1,
+	1, 1, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 4, 4, 4, 4, 5,
+	5, 5, 6, 6, 6, 7, 7, 7,
+	8, 8, 8, 9, 9, 9, 10, 10,
+	11, 11, 12, 12, 12, 13, 13, 14,
+	14, 15, 15, 16, 16, 17, 17, 18,
+	18, 19, 20, 20, 21, 21, 22, 22,
+	23, 24, 24, 25, 26, 26, 27, 28,
+	28, 29, 30, 30, 31, 32, 32, 33,
+	34, 35, 35, 36, 37, 38, 38, 39,
+	40, 41, 41, 42, 43, 44, 45, 46,
+	46, 47, 48, 49, 50, 51, 52, 53,
+	53, 54, 55, 56, 57, 58, 59, 60,
+	61, 62, 63, 64, 65, 66, 67, 68,
+	69, 70, 71, 72, 73, 74, 75, 76,
+	77, 78, 79, 81, 82, 83, 84, 85,
+	86, 87, 88, 90, 91, 92, 93, 94,
+	95, 97, 98, 99, 100, 101, 103, 104,
+	105, 106, 108, 109, 110, 112, 113, 114,
+	115, 117, 118, 119, 121, 122, 123, 125,
+	126, 127, 129, 130, 132, 133, 134, 136,
+	137, 139, 140, 141, 143, 144, 146, 147,
+	149, 150, 152, 153, 155, 156, 158, 159,
+	161, 162, 164, 165, 167, 168, 170, 172,
+	173, 175, 176, 178, 180, 181, 183, 184,
+	186, 188, 189, 191, 193, 194, 196, 198,
+	199, 201, 203, 204, 206, 208, 210, 211,
+	213, 215, 217, 218, 220, 222, 224, 225,
+	227, 229, 231, 233, 235, 236, 238, 240,
+	242, 244, 246, 247, 249, 251, 253, 255,
+};
+
+static const u16 xgamma8_20[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 3, 3, 3, 3, 4, 4,
+	4, 4, 5, 5, 5, 5, 6, 6,
+	6, 7, 7, 7, 8, 8, 8, 9,
+	9, 9, 10, 10, 11, 11, 11, 12,
+	12, 13, 13, 14, 14, 15, 15, 16,
+	16, 17, 17, 18, 18, 19, 19, 20,
+	20, 21, 21, 22, 23, 23, 24, 24,
+	25, 26, 26, 27, 28, 28, 29, 30,
+	30, 31, 32, 32, 33, 34, 35, 35,
+	36, 37, 38, 38, 39, 40, 41, 42,
+	42, 43, 44, 45, 46, 47, 47, 48,
+	49, 50, 51, 52, 53, 54, 55, 56,
+	56, 57, 58, 59, 60, 61, 62, 63,
+	64, 65, 66, 67, 68, 69, 70, 71,
+	73, 74, 75, 76, 77, 78, 79, 80,
+	81, 82, 84, 85, 86, 87, 88, 89,
+	91, 92, 93, 94, 95, 97, 98, 99,
+	100, 102, 103, 104, 105, 107, 108, 109,
+	111, 112, 113, 115, 116, 117, 119, 120,
+	121, 123, 124, 126, 127, 128, 130, 131,
+	133, 134, 136, 137, 139, 140, 142, 143,
+	145, 146, 148, 149, 151, 152, 154, 155,
+	157, 158, 160, 162, 163, 165, 166, 168,
+	170, 171, 173, 175, 176, 178, 180, 181,
+	183, 185, 186, 188, 190, 192, 193, 195,
+	197, 199, 200, 202, 204, 206, 207, 209,
+	211, 213, 215, 217, 218, 220, 222, 224,
+	226, 228, 230, 232, 233, 235, 237, 239,
+	241, 243, 245, 247, 249, 251, 253, 255,
+};
+
+static const u16 xgamma8_21[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 4, 4, 4, 4, 5, 5,
+	5, 5, 6, 6, 6, 7, 7, 7,
+	8, 8, 8, 9, 9, 9, 10, 10,
+	11, 11, 11, 12, 12, 13, 13, 14,
+	14, 14, 15, 15, 16, 16, 17, 17,
+	18, 18, 19, 20, 20, 21, 21, 22,
+	22, 23, 24, 24, 25, 25, 26, 27,
+	27, 28, 29, 29, 30, 31, 31, 32,
+	33, 33, 34, 35, 36, 36, 37, 38,
+	39, 40, 40, 41, 42, 43, 44, 44,
+	45, 46, 47, 48, 49, 50, 51, 51,
+	52, 53, 54, 55, 56, 57, 58, 59,
+	60, 61, 62, 63, 64, 65, 66, 67,
+	68, 69, 70, 71, 72, 73, 75, 76,
+	77, 78, 79, 80, 81, 83, 84, 85,
+	86, 87, 88, 90, 91, 92, 93, 95,
+	96, 97, 98, 100, 101, 102, 104, 105,
+	106, 107, 109, 110, 112, 113, 114, 116,
+	117, 118, 120, 121, 123, 124, 126, 127,
+	129, 130, 131, 133, 134, 136, 137, 139,
+	141, 142, 144, 145, 147, 148, 150, 151,
+	153, 155, 156, 158, 160, 161, 163, 165,
+	166, 168, 170, 171, 173, 175, 176, 178,
+	180, 182, 183, 185, 187, 189, 191, 192,
+	194, 196, 198, 200, 202, 203, 205, 207,
+	209, 211, 213, 215, 217, 219, 221, 223,
+	225, 226, 228, 230, 232, 234, 236, 238,
+	241, 243, 245, 247, 249, 251, 253, 255,
+};
+
+static const u16 xgamma8_22[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2,
+	3, 3, 3, 3, 3, 4, 4, 4,
+	4, 5, 5, 5, 5, 6, 6, 6,
+	6, 7, 7, 7, 8, 8, 8, 9,
+	9, 9, 10, 10, 11, 11, 11, 12,
+	12, 13, 13, 13, 14, 14, 15, 15,
+	16, 16, 17, 17, 18, 18, 19, 19,
+	20, 20, 21, 22, 22, 23, 23, 24,
+	25, 25, 26, 26, 27, 28, 28, 29,
+	30, 30, 31, 32, 33, 33, 34, 35,
+	35, 36, 37, 38, 39, 39, 40, 41,
+	42, 43, 43, 44, 45, 46, 47, 48,
+	49, 49, 50, 51, 52, 53, 54, 55,
+	56, 57, 58, 59, 60, 61, 62, 63,
+	64, 65, 66, 67, 68, 69, 70, 71,
+	73, 74, 75, 76, 77, 78, 79, 81,
+	82, 83, 84, 85, 87, 88, 89, 90,
+	91, 93, 94, 95, 97, 98, 99, 100,
+	102, 103, 105, 106, 107, 109, 110, 111,
+	113, 114, 116, 117, 119, 120, 121, 123,
+	124, 126, 127, 129, 130, 132, 133, 135,
+	137, 138, 140, 141, 143, 145, 146, 148,
+	149, 151, 153, 154, 156, 158, 159, 161,
+	163, 165, 166, 168, 170, 172, 173, 175,
+	177, 179, 181, 182, 184, 186, 188, 190,
+	192, 194, 196, 197, 199, 201, 203, 205,
+	207, 209, 211, 213, 215, 217, 219, 221,
+	223, 225, 227, 229, 231, 234, 236, 238,
+	240, 242, 244, 246, 248, 251, 253, 255,
+};
+
+static const u16 xgamma8_23[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 5, 5, 5,
+	5, 6, 6, 6, 7, 7, 7, 7,
+	8, 8, 8, 9, 9, 10, 10, 10,
+	11, 11, 11, 12, 12, 13, 13, 13,
+	14, 14, 15, 15, 16, 16, 17, 17,
+	18, 18, 19, 19, 20, 20, 21, 21,
+	22, 23, 23, 24, 24, 25, 26, 26,
+	27, 28, 28, 29, 30, 30, 31, 32,
+	32, 33, 34, 35, 35, 36, 37, 38,
+	38, 39, 40, 41, 42, 42, 43, 44,
+	45, 46, 47, 48, 49, 49, 50, 51,
+	52, 53, 54, 55, 56, 57, 58, 59,
+	60, 61, 62, 63, 64, 65, 66, 67,
+	69, 70, 71, 72, 73, 74, 75, 76,
+	78, 79, 80, 81, 82, 84, 85, 86,
+	87, 89, 90, 91, 92, 94, 95, 96,
+	98, 99, 100, 102, 103, 104, 106, 107,
+	109, 110, 112, 113, 114, 116, 117, 119,
+	120, 122, 123, 125, 126, 128, 130, 131,
+	133, 134, 136, 138, 139, 141, 143, 144,
+	146, 148, 149, 151, 153, 154, 156, 158,
+	160, 161, 163, 165, 167, 169, 170, 172,
+	174, 176, 178, 180, 182, 183, 185, 187,
+	189, 191, 193, 195, 197, 199, 201, 203,
+	205, 207, 209, 211, 213, 215, 218, 220,
+	222, 224, 226, 228, 230, 233, 235, 237,
+	239, 241, 244, 246, 248, 250, 253, 255,
+};
+
+static const u16 xgamma8_24[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 2, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4,
+	5, 5, 5, 5, 6, 6, 6, 6,
+	7, 7, 7, 8, 8, 8, 9, 9,
+	9, 10, 10, 10, 11, 11, 11, 12,
+	12, 13, 13, 14, 14, 14, 15, 15,
+	16, 16, 17, 17, 18, 18, 19, 19,
+	20, 20, 21, 22, 22, 23, 23, 24,
+	24, 25, 26, 26, 27, 28, 28, 29,
+	30, 30, 31, 32, 32, 33, 34, 35,
+	35, 36, 37, 38, 39, 39, 40, 41,
+	42, 43, 43, 44, 45, 46, 47, 48,
+	49, 50, 51, 52, 53, 53, 54, 55,
+	56, 57, 58, 59, 60, 62, 63, 64,
+	65, 66, 67, 68, 69, 70, 71, 73,
+	74, 75, 76, 77, 78, 80, 81, 82,
+	83, 85, 86, 87, 88, 90, 91, 92,
+	94, 95, 96, 98, 99, 100, 102, 103,
+	105, 106, 108, 109, 111, 112, 114, 115,
+	117, 118, 120, 121, 123, 124, 126, 127,
+	129, 131, 132, 134, 136, 137, 139, 141,
+	142, 144, 146, 148, 149, 151, 153, 155,
+	156, 158, 160, 162, 164, 166, 167, 169,
+	171, 173, 175, 177, 179, 181, 183, 185,
+	187, 189, 191, 193, 195, 197, 199, 201,
+	203, 205, 207, 210, 212, 214, 216, 218,
+	220, 223, 225, 227, 229, 232, 234, 236,
+	239, 241, 243, 246, 248, 250, 253, 255,
+};
+
+static const u16 xgamma8_25[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2,
+	2, 3, 3, 3, 3, 3, 4, 4,
+	4, 4, 4, 5, 5, 5, 5, 6,
+	6, 6, 6, 7, 7, 7, 7, 8,
+	8, 8, 9, 9, 9, 10, 10, 10,
+	11, 11, 12, 12, 12, 13, 13, 14,
+	14, 15, 15, 15, 16, 16, 17, 17,
+	18, 18, 19, 19, 20, 20, 21, 22,
+	22, 23, 23, 24, 25, 25, 26, 26,
+	27, 28, 28, 29, 30, 30, 31, 32,
+	33, 33, 34, 35, 36, 36, 37, 38,
+	39, 40, 40, 41, 42, 43, 44, 45,
+	46, 46, 47, 48, 49, 50, 51, 52,
+	53, 54, 55, 56, 57, 58, 59, 60,
+	61, 62, 63, 64, 65, 67, 68, 69,
+	70, 71, 72, 73, 75, 76, 77, 78,
+	80, 81, 82, 83, 85, 86, 87, 89,
+	90, 91, 93, 94, 95, 97, 98, 99,
+	101, 102, 104, 105, 107, 108, 110, 111,
+	113, 114, 116, 117, 119, 121, 122, 124,
+	125, 127, 129, 130, 132, 134, 135, 137,
+	139, 141, 142, 144, 146, 148, 150, 151,
+	153, 155, 157, 159, 161, 163, 165, 166,
+	168, 170, 172, 174, 176, 178, 180, 182,
+	184, 186, 189, 191, 193, 195, 197, 199,
+	201, 204, 206, 208, 210, 212, 215, 217,
+	219, 221, 224, 226, 228, 231, 233, 235,
+	238, 240, 243, 245, 248, 250, 253, 255,
+};
+
+static const u16 xgamma8_26[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3,
+	3, 3, 4, 4, 4, 4, 5, 5,
+	5, 5, 5, 6, 6, 6, 6, 7,
+	7, 7, 8, 8, 8, 9, 9, 9,
+	10, 10, 10, 11, 11, 11, 12, 12,
+	13, 13, 13, 14, 14, 15, 15, 16,
+	16, 17, 17, 18, 18, 19, 19, 20,
+	20, 21, 21, 22, 22, 23, 24, 24,
+	25, 25, 26, 27, 27, 28, 29, 29,
+	30, 31, 31, 32, 33, 34, 34, 35,
+	36, 37, 38, 38, 39, 40, 41, 42,
+	42, 43, 44, 45, 46, 47, 48, 49,
+	50, 51, 52, 53, 54, 55, 56, 57,
+	58, 59, 60, 61, 62, 63, 64, 65,
+	66, 68, 69, 70, 71, 72, 73, 75,
+	76, 77, 78, 80, 81, 82, 84, 85,
+	86, 88, 89, 90, 92, 93, 94, 96,
+	97, 99, 100, 102, 103, 105, 106, 108,
+	109, 111, 112, 114, 115, 117, 119, 120,
+	122, 124, 125, 127, 129, 130, 132, 134,
+	136, 137, 139, 141, 143, 145, 146, 148,
+	150, 152, 154, 156, 158, 160, 162, 164,
+	166, 168, 170, 172, 174, 176, 178, 180,
+	182, 184, 186, 188, 191, 193, 195, 197,
+	199, 202, 204, 206, 209, 211, 213, 215,
+	218, 220, 223, 225, 227, 230, 232, 235,
+	237, 240, 242, 245, 247, 250, 252, 255,
+};
+
+static const u16 xgamma8_27[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 2, 3, 3,
+	3, 3, 3, 3, 3, 4, 4, 4,
+	4, 4, 5, 5, 5, 5, 6, 6,
+	6, 6, 7, 7, 7, 7, 8, 8,
+	8, 9, 9, 9, 10, 10, 10, 11,
+	11, 12, 12, 12, 13, 13, 14, 14,
+	14, 15, 15, 16, 16, 17, 17, 18,
+	18, 19, 19, 20, 20, 21, 21, 22,
+	23, 23, 24, 24, 25, 26, 26, 27,
+	28, 28, 29, 30, 30, 31, 32, 33,
+	33, 34, 35, 36, 36, 37, 38, 39,
+	40, 41, 41, 42, 43, 44, 45, 46,
+	47, 48, 49, 50, 51, 51, 52, 53,
+	55, 56, 57, 58, 59, 60, 61, 62,
+	63, 64, 65, 66, 68, 69, 70, 71,
+	72, 74, 75, 76, 77, 79, 80, 81,
+	83, 84, 85, 87, 88, 89, 91, 92,
+	94, 95, 97, 98, 100, 101, 103, 104,
+	106, 107, 109, 110, 112, 114, 115, 117,
+	119, 120, 122, 124, 125, 127, 129, 131,
+	132, 134, 136, 138, 140, 141, 143, 145,
+	147, 149, 151, 153, 155, 157, 159, 161,
+	163, 165, 167, 169, 171, 173, 175, 178,
+	180, 182, 184, 186, 188, 191, 193, 195,
+	198, 200, 202, 205, 207, 209, 212, 214,
+	216, 219, 221, 224, 226, 229, 231, 234,
+	237, 239, 242, 244, 247, 250, 252, 255,
+};
+
+static const u16 xgamma8_28[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2,
+	2, 3, 3, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 5, 5, 5,
+	5, 6, 6, 6, 6, 7, 7, 7,
+	7, 8, 8, 8, 9, 9, 9, 10,
+	10, 10, 11, 11, 11, 12, 12, 13,
+	13, 13, 14, 14, 15, 15, 16, 16,
+	17, 17, 18, 18, 19, 19, 20, 20,
+	21, 21, 22, 22, 23, 24, 24, 25,
+	25, 26, 27, 27, 28, 29, 29, 30,
+	31, 32, 32, 33, 34, 35, 35, 36,
+	37, 38, 39, 39, 40, 41, 42, 43,
+	44, 45, 46, 47, 48, 49, 50, 50,
+	51, 52, 54, 55, 56, 57, 58, 59,
+	60, 61, 62, 63, 64, 66, 67, 68,
+	69, 70, 72, 73, 74, 75, 77, 78,
+	79, 81, 82, 83, 85, 86, 87, 89,
+	90, 92, 93, 95, 96, 98, 99, 101,
+	102, 104, 105, 107, 109, 110, 112, 114,
+	115, 117, 119, 120, 122, 124, 126, 127,
+	129, 131, 133, 135, 137, 138, 140, 142,
+	144, 146, 148, 150, 152, 154, 156, 158,
+	160, 162, 164, 167, 169, 171, 173, 175,
+	177, 180, 182, 184, 186, 189, 191, 193,
+	196, 198, 200, 203, 205, 208, 210, 213,
+	215, 218, 220, 223, 225, 228, 231, 233,
+	236, 239, 241, 244, 247, 249, 252, 255,
+};
+
+static const u16 xgamma8_29[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4,
+	5, 5, 5, 5, 6, 6, 6, 6,
+	7, 7, 7, 7, 8, 8, 8, 9,
+	9, 9, 9, 10, 10, 11, 11, 11,
+	12, 12, 12, 13, 13, 14, 14, 15,
+	15, 15, 16, 16, 17, 17, 18, 18,
+	19, 19, 20, 21, 21, 22, 22, 23,
+	23, 24, 25, 25, 26, 27, 27, 28,
+	29, 29, 30, 31, 32, 32, 33, 34,
+	35, 35, 36, 37, 38, 39, 39, 40,
+	41, 42, 43, 44, 45, 46, 47, 48,
+	49, 50, 51, 52, 53, 54, 55, 56,
+	57, 58, 59, 60, 61, 62, 64, 65,
+	66, 67, 68, 70, 71, 72, 73, 75,
+	76, 77, 79, 80, 81, 83, 84, 86,
+	87, 88, 90, 91, 93, 94, 96, 97,
+	99, 101, 102, 104, 105, 107, 109, 110,
+	112, 114, 115, 117, 119, 121, 122, 124,
+	126, 128, 130, 132, 134, 135, 137, 139,
+	141, 143, 145, 147, 149, 151, 153, 155,
+	158, 160, 162, 164, 166, 168, 171, 173,
+	175, 177, 180, 182, 184, 187, 189, 191,
+	194, 196, 199, 201, 204, 206, 209, 211,
+	214, 216, 219, 222, 224, 227, 230, 232,
+	235, 238, 241, 244, 246, 249, 252, 255,
+};
+
+static const u16 xgamma8_30[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 3, 3, 3, 4, 4,
+	4, 4, 4, 5, 5, 5, 5, 6,
+	6, 6, 6, 6, 7, 7, 7, 8,
+	8, 8, 8, 9, 9, 9, 10, 10,
+	10, 11, 11, 12, 12, 12, 13, 13,
+	14, 14, 14, 15, 15, 16, 16, 17,
+	17, 18, 18, 19, 19, 20, 20, 21,
+	22, 22, 23, 23, 24, 25, 25, 26,
+	27, 27, 28, 29, 29, 30, 31, 32,
+	32, 33, 34, 35, 35, 36, 37, 38,
+	39, 40, 40, 41, 42, 43, 44, 45,
+	46, 47, 48, 49, 50, 51, 52, 53,
+	54, 55, 56, 57, 58, 60, 61, 62,
+	63, 64, 65, 67, 68, 69, 70, 72,
+	73, 74, 76, 77, 78, 80, 81, 82,
+	84, 85, 87, 88, 90, 91, 93, 94,
+	96, 97, 99, 101, 102, 104, 105, 107,
+	109, 111, 112, 114, 116, 118, 119, 121,
+	123, 125, 127, 129, 131, 132, 134, 136,
+	138, 140, 142, 144, 147, 149, 151, 153,
+	155, 157, 159, 162, 164, 166, 168, 171,
+	173, 175, 178, 180, 182, 185, 187, 190,
+	192, 195, 197, 200, 202, 205, 207, 210,
+	213, 215, 218, 221, 223, 226, 229, 232,
+	235, 237, 240, 243, 246, 249, 252, 255,
+};
+
+static const u16 xgamma8_31[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 3, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 4, 5, 5,
+	5, 5, 6, 6, 6, 6, 6, 7,
+	7, 7, 8, 8, 8, 8, 9, 9,
+	9, 10, 10, 10, 11, 11, 12, 12,
+	12, 13, 13, 14, 14, 14, 15, 15,
+	16, 16, 17, 17, 18, 18, 19, 19,
+	20, 20, 21, 22, 22, 23, 23, 24,
+	25, 25, 26, 27, 27, 28, 29, 29,
+	30, 31, 32, 32, 33, 34, 35, 36,
+	36, 37, 38, 39, 40, 41, 42, 42,
+	43, 44, 45, 46, 47, 48, 49, 50,
+	51, 52, 53, 54, 56, 57, 58, 59,
+	60, 61, 62, 64, 65, 66, 67, 69,
+	70, 71, 73, 74, 75, 77, 78, 79,
+	81, 82, 84, 85, 87, 88, 90, 91,
+	93, 94, 96, 97, 99, 101, 102, 104,
+	106, 108, 109, 111, 113, 115, 116, 118,
+	120, 122, 124, 126, 128, 130, 132, 134,
+	136, 138, 140, 142, 144, 146, 148, 150,
+	152, 155, 157, 159, 161, 164, 166, 168,
+	171, 173, 175, 178, 180, 183, 185, 188,
+	190, 193, 195, 198, 201, 203, 206, 209,
+	211, 214, 217, 220, 222, 225, 228, 231,
+	234, 237, 240, 243, 246, 249, 252, 255,
+};
+
+static const u16 xgamma8_32[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4,
+	4, 5, 5, 5, 5, 6, 6, 6,
+	6, 6, 7, 7, 7, 8, 8, 8,
+	8, 9, 9, 9, 10, 10, 10, 11,
+	11, 12, 12, 12, 13, 13, 14, 14,
+	14, 15, 15, 16, 16, 17, 17, 18,
+	18, 19, 19, 20, 21, 21, 22, 22,
+	23, 23, 24, 25, 25, 26, 27, 27,
+	28, 29, 30, 30, 31, 32, 33, 33,
+	34, 35, 36, 37, 37, 38, 39, 40,
+	41, 42, 43, 44, 45, 46, 47, 48,
+	49, 50, 51, 52, 53, 54, 55, 56,
+	57, 59, 60, 61, 62, 63, 65, 66,
+	67, 68, 70, 71, 72, 74, 75, 76,
+	78, 79, 81, 82, 84, 85, 87, 88,
+	90, 91, 93, 95, 96, 98, 99, 101,
+	103, 105, 106, 108, 110, 112, 113, 115,
+	117, 119, 121, 123, 125, 127, 129, 131,
+	133, 135, 137, 139, 141, 143, 146, 148,
+	150, 152, 154, 157, 159, 161, 164, 166,
+	168, 171, 173, 176, 178, 181, 183, 186,
+	188, 191, 194, 196, 199, 202, 204, 207,
+	210, 213, 216, 219, 221, 224, 227, 230,
+	233, 236, 239, 242, 246, 249, 252, 255,
+};
+
+static const u16 xgamma8_33[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 3, 3, 3, 4, 4,
+	4, 4, 4, 4, 5, 5, 5, 5,
+	6, 6, 6, 6, 7, 7, 7, 7,
+	8, 8, 8, 9, 9, 9, 9, 10,
+	10, 11, 11, 11, 12, 12, 12, 13,
+	13, 14, 14, 15, 15, 15, 16, 16,
+	17, 17, 18, 18, 19, 19, 20, 21,
+	21, 22, 22, 23, 24, 24, 25, 26,
+	26, 27, 28, 28, 29, 30, 31, 31,
+	32, 33, 34, 34, 35, 36, 37, 38,
+	39, 40, 40, 41, 42, 43, 44, 45,
+	46, 47, 48, 49, 50, 51, 53, 54,
+	55, 56, 57, 58, 59, 61, 62, 63,
+	64, 66, 67, 68, 70, 71, 72, 74,
+	75, 76, 78, 79, 81, 82, 84, 85,
+	87, 88, 90, 92, 93, 95, 97, 98,
+	100, 102, 103, 105, 107, 109, 111, 113,
+	114, 116, 118, 120, 122, 124, 126, 128,
+	130, 132, 134, 136, 139, 141, 143, 145,
+	147, 150, 152, 154, 157, 159, 161, 164,
+	166, 169, 171, 174, 176, 179, 181, 184,
+	187, 189, 192, 195, 198, 200, 203, 206,
+	209, 212, 215, 217, 220, 223, 226, 230,
+	233, 236, 239, 242, 245, 248, 252, 255,
+};
+
+static const u16 xgamma8_34[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 3, 3, 3, 3, 3, 3,
+	3, 4, 4, 4, 4, 4, 5, 5,
+	5, 5, 5, 6, 6, 6, 6, 7,
+	7, 7, 7, 8, 8, 8, 9, 9,
+	9, 10, 10, 10, 11, 11, 11, 12,
+	12, 12, 13, 13, 14, 14, 15, 15,
+	16, 16, 17, 17, 18, 18, 19, 19,
+	20, 20, 21, 21, 22, 23, 23, 24,
+	24, 25, 26, 26, 27, 28, 29, 29,
+	30, 31, 32, 32, 33, 34, 35, 36,
+	37, 37, 38, 39, 40, 41, 42, 43,
+	44, 45, 46, 47, 48, 49, 50, 51,
+	52, 53, 55, 56, 57, 58, 59, 60,
+	62, 63, 64, 66, 67, 68, 70, 71,
+	72, 74, 75, 77, 78, 80, 81, 83,
+	84, 86, 87, 89, 90, 92, 94, 95,
+	97, 99, 101, 102, 104, 106, 108, 110,
+	112, 114, 115, 117, 119, 121, 123, 125,
+	128, 130, 132, 134, 136, 138, 141, 143,
+	145, 147, 150, 152, 154, 157, 159, 162,
+	164, 167, 169, 172, 174, 177, 180, 182,
+	185, 188, 190, 193, 196, 199, 202, 205,
+	208, 210, 213, 216, 219, 223, 226, 229,
+	232, 235, 238, 242, 245, 248, 252, 255,
+};
+
+static const u16 xgamma8_35[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4,
+	4, 5, 5, 5, 5, 5, 6, 6,
+	6, 6, 7, 7, 7, 7, 8, 8,
+	8, 9, 9, 9, 10, 10, 10, 11,
+	11, 11, 12, 12, 13, 13, 13, 14,
+	14, 15, 15, 16, 16, 17, 17, 18,
+	18, 19, 19, 20, 20, 21, 22, 22,
+	23, 23, 24, 25, 25, 26, 27, 28,
+	28, 29, 30, 30, 31, 32, 33, 34,
+	35, 35, 36, 37, 38, 39, 40, 41,
+	42, 43, 44, 45, 46, 47, 48, 49,
+	50, 51, 52, 53, 54, 56, 57, 58,
+	59, 60, 62, 63, 64, 66, 67, 68,
+	70, 71, 72, 74, 75, 77, 78, 80,
+	81, 83, 85, 86, 88, 89, 91, 93,
+	94, 96, 98, 100, 102, 103, 105, 107,
+	109, 111, 113, 115, 117, 119, 121, 123,
+	125, 127, 129, 131, 134, 136, 138, 140,
+	143, 145, 147, 150, 152, 155, 157, 159,
+	162, 165, 167, 170, 172, 175, 178, 180,
+	183, 186, 189, 192, 194, 197, 200, 203,
+	206, 209, 212, 215, 219, 222, 225, 228,
+	231, 235, 238, 241, 245, 248, 252, 255,
+};
+
+static const u16 xgamma8_36[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 3, 3, 3, 4, 4,
+	4, 4, 4, 4, 5, 5, 5, 5,
+	6, 6, 6, 6, 6, 7, 7, 7,
+	8, 8, 8, 8, 9, 9, 9, 10,
+	10, 10, 11, 11, 12, 12, 12, 13,
+	13, 14, 14, 15, 15, 15, 16, 16,
+	17, 17, 18, 18, 19, 20, 20, 21,
+	21, 22, 23, 23, 24, 24, 25, 26,
+	27, 27, 28, 29, 29, 30, 31, 32,
+	33, 33, 34, 35, 36, 37, 38, 39,
+	40, 41, 42, 42, 43, 44, 46, 47,
+	48, 49, 50, 51, 52, 53, 54, 56,
+	57, 58, 59, 61, 62, 63, 64, 66,
+	67, 69, 70, 71, 73, 74, 76, 77,
+	79, 80, 82, 83, 85, 87, 88, 90,
+	92, 94, 95, 97, 99, 101, 103, 104,
+	106, 108, 110, 112, 114, 116, 118, 120,
+	122, 125, 127, 129, 131, 133, 136, 138,
+	140, 143, 145, 147, 150, 152, 155, 157,
+	160, 162, 165, 168, 170, 173, 176, 179,
+	181, 184, 187, 190, 193, 196, 199, 202,
+	205, 208, 211, 214, 218, 221, 224, 227,
+	231, 234, 237, 241, 244, 248, 251, 255,
+};
+
+static const u16 xgamma8_37[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 3, 3, 3, 3, 3, 3,
+	3, 4, 4, 4, 4, 4, 5, 5,
+	5, 5, 5, 6, 6, 6, 6, 7,
+	7, 7, 7, 8, 8, 8, 9, 9,
+	9, 10, 10, 10, 11, 11, 11, 12,
+	12, 13, 13, 13, 14, 14, 15, 15,
+	16, 16, 17, 17, 18, 18, 19, 19,
+	20, 20, 21, 22, 22, 23, 24, 24,
+	25, 26, 26, 27, 28, 28, 29, 30,
+	31, 32, 32, 33, 34, 35, 36, 37,
+	38, 39, 39, 40, 41, 42, 43, 44,
+	45, 47, 48, 49, 50, 51, 52, 53,
+	54, 56, 57, 58, 59, 61, 62, 63,
+	65, 66, 67, 69, 70, 72, 73, 75,
+	76, 78, 79, 81, 83, 84, 86, 88,
+	89, 91, 93, 95, 96, 98, 100, 102,
+	104, 106, 108, 110, 112, 114, 116, 118,
+	120, 122, 124, 127, 129, 131, 133, 136,
+	138, 140, 143, 145, 148, 150, 153, 155,
+	158, 160, 163, 166, 169, 171, 174, 177,
+	180, 183, 186, 188, 191, 194, 198, 201,
+	204, 207, 210, 213, 217, 220, 223, 227,
+	230, 233, 237, 241, 244, 248, 251, 255,
+};
+
+static const u16 xgamma8_38[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4,
+	4, 5, 5, 5, 5, 6, 6, 6,
+	6, 6, 7, 7, 7, 8, 8, 8,
+	8, 9, 9, 9, 10, 10, 10, 11,
+	11, 12, 12, 12, 13, 13, 14, 14,
+	15, 15, 15, 16, 16, 17, 18, 18,
+	19, 19, 20, 20, 21, 21, 22, 23,
+	23, 24, 25, 25, 26, 27, 28, 28,
+	29, 30, 31, 31, 32, 33, 34, 35,
+	36, 37, 38, 38, 39, 40, 41, 42,
+	43, 44, 45, 47, 48, 49, 50, 51,
+	52, 53, 55, 56, 57, 58, 60, 61,
+	62, 64, 65, 66, 68, 69, 71, 72,
+	74, 75, 77, 78, 80, 82, 83, 85,
+	87, 88, 90, 92, 94, 96, 98, 99,
+	101, 103, 105, 107, 109, 111, 113, 115,
+	118, 120, 122, 124, 126, 129, 131, 133,
+	136, 138, 141, 143, 146, 148, 151, 153,
+	156, 158, 161, 164, 167, 169, 172, 175,
+	178, 181, 184, 187, 190, 193, 196, 199,
+	203, 206, 209, 212, 216, 219, 222, 226,
+	229, 233, 237, 240, 244, 247, 251, 255,
+};
+
+static const u16 xgamma8_39[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 3, 3,
+	3, 3, 3, 3, 3, 4, 4, 4,
+	4, 4, 4, 5, 5, 5, 5, 5,
+	6, 6, 6, 6, 7, 7, 7, 7,
+	8, 8, 8, 9, 9, 9, 10, 10,
+	10, 11, 11, 11, 12, 12, 13, 13,
+	13, 14, 14, 15, 15, 16, 16, 17,
+	17, 18, 18, 19, 20, 20, 21, 21,
+	22, 23, 23, 24, 25, 25, 26, 27,
+	27, 28, 29, 30, 31, 31, 32, 33,
+	34, 35, 36, 37, 38, 38, 39, 40,
+	41, 42, 43, 45, 46, 47, 48, 49,
+	50, 51, 52, 54, 55, 56, 57, 59,
+	60, 61, 63, 64, 66, 67, 68, 70,
+	71, 73, 74, 76, 78, 79, 81, 83,
+	84, 86, 88, 90, 91, 93, 95, 97,
+	99, 101, 103, 105, 107, 109, 111, 113,
+	115, 117, 120, 122, 124, 126, 129, 131,
+	133, 136, 138, 141, 143, 146, 149, 151,
+	154, 157, 159, 162, 165, 168, 171, 173,
+	176, 179, 182, 185, 189, 192, 195, 198,
+	201, 205, 208, 211, 215, 218, 222, 225,
+	229, 232, 236, 240, 243, 247, 251, 255,
+};
+
+static const u16 xgamma8_40[GAMMA8_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 2, 2, 2,
+	2, 3, 3, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 5, 5, 5,
+	5, 5, 6, 6, 6, 6, 7, 7,
+	7, 7, 8, 8, 8, 9, 9, 9,
+	9, 10, 10, 11, 11, 11, 12, 12,
+	13, 13, 13, 14, 14, 15, 15, 16,
+	16, 17, 17, 18, 18, 19, 19, 20,
+	21, 21, 22, 23, 23, 24, 25, 25,
+	26, 27, 27, 28, 29, 30, 31, 31,
+	32, 33, 34, 35, 36, 37, 38, 39,
+	40, 41, 42, 43, 44, 45, 46, 47,
+	48, 49, 50, 52, 53, 54, 55, 57,
+	58, 59, 61, 62, 63, 65, 66, 68,
+	69, 71, 72, 74, 75, 77, 79, 80,
+	82, 84, 85, 87, 89, 91, 93, 95,
+	96, 98, 100, 102, 104, 107, 109, 111,
+	113, 115, 117, 120, 122, 124, 126, 129,
+	131, 134, 136, 139, 141, 144, 146, 149,
+	152, 155, 157, 160, 163, 166, 169, 172,
+	175, 178, 181, 184, 187, 190, 194, 197,
+	200, 203, 207, 210, 214, 217, 221, 224,
+	228, 232, 236, 239, 243, 247, 251, 255,
+};
+
+static const u16 *xgamma8_curves[GAMMA_CURVE_LENGTH] =  {
+	&xgamma8_01[0],
+	&xgamma8_02[0],
+	&xgamma8_03[0],
+	&xgamma8_04[0],
+	&xgamma8_05[0],
+	&xgamma8_06[0],
+	&xgamma8_07[0],
+	&xgamma8_08[0],
+	&xgamma8_09[0],
+	&xgamma8_10[0],
+	&xgamma8_11[0],
+	&xgamma8_12[0],
+	&xgamma8_13[0],
+	&xgamma8_14[0],
+	&xgamma8_15[0],
+	&xgamma8_16[0],
+	&xgamma8_17[0],
+	&xgamma8_18[0],
+	&xgamma8_19[0],
+	&xgamma8_20[0],
+	&xgamma8_21[0],
+	&xgamma8_22[0],
+	&xgamma8_23[0],
+	&xgamma8_24[0],
+	&xgamma8_25[0],
+	&xgamma8_26[0],
+	&xgamma8_27[0],
+	&xgamma8_28[0],
+	&xgamma8_29[0],
+	&xgamma8_30[0],
+	&xgamma8_31[0],
+	&xgamma8_32[0],
+	&xgamma8_33[0],
+	&xgamma8_34[0],
+	&xgamma8_35[0],
+	&xgamma8_36[0],
+	&xgamma8_37[0],
+	&xgamma8_38[0],
+	&xgamma8_39[0],
+	&xgamma8_40[0],
+};
+
+#define GAMMA_BPC_10		(10)
+#define GAMMA10_TABLE_LENGTH	BIT(GAMMA_BPC_10)
+static const u16 xgamma10_01[GAMMA10_TABLE_LENGTH] = {
+	0, 512, 548, 571, 588, 601, 612, 621, 630, 637, 644,
+	650, 656, 661, 666, 671, 675, 679, 683, 687, 690, 694,
+	697, 700, 703, 706, 709, 711, 714, 716, 719, 721, 723,
+	726, 728, 730, 732, 734, 736, 738, 740, 742, 743, 745,
+	747, 749, 750, 752, 753, 755, 756, 758, 759, 761, 762,
+	764, 765, 766, 768, 769, 770, 772, 773, 774, 775, 777,
+	778, 779, 780, 781, 782, 783, 785, 786, 787, 788, 789,
+	790, 791, 792, 793, 794, 795, 796, 797, 798, 799, 800,
+	800, 801, 802, 803, 804, 805, 806, 807, 807, 808, 809,
+	810, 811, 812, 812, 813, 814, 815, 815, 816, 817, 818,
+	819, 819, 820, 821, 821, 822, 823, 824, 824, 825, 826,
+	826, 827, 828, 828, 829, 830, 830, 831, 832, 832, 833,
+	834, 834, 835, 835, 836, 837, 837, 838, 838, 839, 840,
+	840, 841, 841, 842, 843, 843, 844, 844, 845, 845, 846,
+	847, 847, 848, 848, 849, 849, 850, 850, 851, 851, 852,
+	852, 853, 853, 854, 854, 855, 855, 856, 856, 857, 857,
+	858, 858, 859, 859, 860, 860, 861, 861, 862, 862, 863,
+	863, 864, 864, 864, 865, 865, 866, 866, 867, 867, 868,
+	868, 869, 869, 869, 870, 870, 871, 871, 872, 872, 872,
+	873, 873, 874, 874, 874, 875, 875, 876, 876, 876, 877,
+	877, 878, 878, 878, 879, 879, 880, 880, 880, 881, 881,
+	882, 882, 882, 883, 883, 883, 884, 884, 885, 885, 885,
+	886, 886, 886, 887, 887, 887, 888, 888, 889, 889, 889,
+	890, 890, 890, 891, 891, 891, 892, 892, 892, 893, 893,
+	893, 894, 894, 894, 895, 895, 895, 896, 896, 896, 897,
+	897, 897, 898, 898, 898, 899, 899, 899, 900, 900, 900,
+	901, 901, 901, 902, 902, 902, 902, 903, 903, 903, 904,
+	904, 904, 905, 905, 905, 906, 906, 906, 906, 907, 907,
+	907, 908, 908, 908, 908, 909, 909, 909, 910, 910, 910,
+	910, 911, 911, 911, 912, 912, 912, 912, 913, 913, 913,
+	914, 914, 914, 914, 915, 915, 915, 915, 916, 916, 916,
+	917, 917, 917, 917, 918, 918, 918, 918, 919, 919, 919,
+	919, 920, 920, 920, 921, 921, 921, 921, 922, 922, 922,
+	922, 923, 923, 923, 923, 924, 924, 924, 924, 925, 925,
+	925, 925, 926, 926, 926, 926, 927, 927, 927, 927, 928,
+	928, 928, 928, 928, 929, 929, 929, 929, 930, 930, 930,
+	930, 931, 931, 931, 931, 932, 932, 932, 932, 932, 933,
+	933, 933, 933, 934, 934, 934, 934, 935, 935, 935, 935,
+	935, 936, 936, 936, 936, 937, 937, 937, 937, 937, 938,
+	938, 938, 938, 939, 939, 939, 939, 939, 940, 940, 940,
+	940, 940, 941, 941, 941, 941, 942, 942, 942, 942, 942,
+	943, 943, 943, 943, 943, 944, 944, 944, 944, 944, 945,
+	945, 945, 945, 945, 946, 946, 946, 946, 946, 947, 947,
+	947, 947, 947, 948, 948, 948, 948, 948, 949, 949, 949,
+	949, 949, 950, 950, 950, 950, 950, 951, 951, 951, 951,
+	951, 952, 952, 952, 952, 952, 953, 953, 953, 953, 953,
+	953, 954, 954, 954, 954, 954, 955, 955, 955, 955, 955,
+	956, 956, 956, 956, 956, 956, 957, 957, 957, 957, 957,
+	958, 958, 958, 958, 958, 958, 959, 959, 959, 959, 959,
+	960, 960, 960, 960, 960, 960, 961, 961, 961, 961, 961,
+	961, 962, 962, 962, 962, 962, 962, 963, 963, 963, 963,
+	963, 964, 964, 964, 964, 964, 964, 965, 965, 965, 965,
+	965, 965, 966, 966, 966, 966, 966, 966, 967, 967, 967,
+	967, 967, 967, 968, 968, 968, 968, 968, 968, 969, 969,
+	969, 969, 969, 969, 970, 970, 970, 970, 970, 970, 970,
+	971, 971, 971, 971, 971, 971, 972, 972, 972, 972, 972,
+	972, 973, 973, 973, 973, 973, 973, 974, 974, 974, 974,
+	974, 974, 974, 975, 975, 975, 975, 975, 975, 976, 976,
+	976, 976, 976, 976, 976, 977, 977, 977, 977, 977, 977,
+	977, 978, 978, 978, 978, 978, 978, 979, 979, 979, 979,
+	979, 979, 979, 980, 980, 980, 980, 980, 980, 980, 981,
+	981, 981, 981, 981, 981, 981, 982, 982, 982, 982, 982,
+	982, 982, 983, 983, 983, 983, 983, 983, 983, 984, 984,
+	984, 984, 984, 984, 984, 985, 985, 985, 985, 985, 985,
+	985, 986, 986, 986, 986, 986, 986, 986, 987, 987, 987,
+	987, 987, 987, 987, 988, 988, 988, 988, 988, 988, 988,
+	989, 989, 989, 989, 989, 989, 989, 989, 990, 990, 990,
+	990, 990, 990, 990, 991, 991, 991, 991, 991, 991, 991,
+	991, 992, 992, 992, 992, 992, 992, 992, 993, 993, 993,
+	993, 993, 993, 993, 993, 994, 994, 994, 994, 994, 994,
+	994, 994, 995, 995, 995, 995, 995, 995, 995, 996, 996,
+	996, 996, 996, 996, 996, 996, 997, 997, 997, 997, 997,
+	997, 997, 997, 998, 998, 998, 998, 998, 998, 998, 998,
+	999, 999, 999, 999, 999, 999, 999, 999, 1000, 1000, 1000,
+	1000, 1000, 1000, 1000, 1000, 1000, 1001, 1001, 1001, 1001, 1001,
+	1001, 1001, 1001, 1002, 1002, 1002, 1002, 1002, 1002, 1002, 1002,
+	1003, 1003, 1003, 1003, 1003, 1003, 1003, 1003, 1004, 1004, 1004,
+	1004, 1004, 1004, 1004, 1004, 1004, 1005, 1005, 1005, 1005, 1005,
+	1005, 1005, 1005, 1006, 1006, 1006, 1006, 1006, 1006, 1006, 1006,
+	1006, 1007, 1007, 1007, 1007, 1007, 1007, 1007, 1007, 1007, 1008,
+	1008, 1008, 1008, 1008, 1008, 1008, 1008, 1009, 1009, 1009, 1009,
+	1009, 1009, 1009, 1009, 1009, 1010, 1010, 1010, 1010, 1010, 1010,
+	1010, 1010, 1010, 1011, 1011, 1011, 1011, 1011, 1011, 1011, 1011,
+	1011, 1012, 1012, 1012, 1012, 1012, 1012, 1012, 1012, 1012, 1013,
+	1013, 1013, 1013, 1013, 1013, 1013, 1013, 1013, 1014, 1014, 1014,
+	1014, 1014, 1014, 1014, 1014, 1014, 1014, 1015, 1015, 1015, 1015,
+	1015, 1015, 1015, 1015, 1015, 1016, 1016, 1016, 1016, 1016, 1016,
+	1016, 1016, 1016, 1017, 1017, 1017, 1017, 1017, 1017, 1017, 1017,
+	1017, 1017, 1018, 1018, 1018, 1018, 1018, 1018, 1018, 1018, 1018,
+	1019, 1019, 1019, 1019, 1019, 1019, 1019, 1019, 1019, 1019, 1020,
+	1020, 1020, 1020, 1020, 1020, 1020, 1020, 1020, 1020, 1021, 1021,
+	1021, 1021, 1021, 1021, 1021, 1021, 1021, 1021, 1022, 1022, 1022,
+	1022, 1022, 1022, 1022, 1022, 1022, 1022, 1023, 1023, 1023, 1023,
+	1023,
+};
+
+static const u16 xgamma10_02[GAMMA10_TABLE_LENGTH] = {
+	0, 256, 294, 319, 338, 353, 366, 378, 388, 397, 405,
+	413, 420, 427, 434, 440, 445, 451, 456, 461, 466, 470,
+	475, 479, 483, 487, 491, 495, 498, 502, 505, 508, 512,
+	515, 518, 521, 524, 527, 529, 532, 535, 538, 540, 543,
+	545, 548, 550, 552, 555, 557, 559, 562, 564, 566, 568,
+	570, 572, 574, 576, 578, 580, 582, 584, 586, 588, 589,
+	591, 593, 595, 597, 598, 600, 602, 603, 605, 607, 608,
+	610, 611, 613, 614, 616, 618, 619, 621, 622, 623, 625,
+	626, 628, 629, 631, 632, 633, 635, 636, 637, 639, 640,
+	641, 643, 644, 645, 646, 648, 649, 650, 651, 653, 654,
+	655, 656, 657, 658, 660, 661, 662, 663, 664, 665, 666,
+	668, 669, 670, 671, 672, 673, 674, 675, 676, 677, 678,
+	679, 680, 681, 682, 683, 684, 685, 686, 687, 688, 689,
+	690, 691, 692, 693, 694, 695, 696, 697, 698, 699, 700,
+	700, 701, 702, 703, 704, 705, 706, 707, 708, 708, 709,
+	710, 711, 712, 713, 714, 714, 715, 716, 717, 718, 719,
+	719, 720, 721, 722, 723, 723, 724, 725, 726, 727, 727,
+	728, 729, 730, 731, 731, 732, 733, 734, 734, 735, 736,
+	737, 737, 738, 739, 740, 740, 741, 742, 742, 743, 744,
+	745, 745, 746, 747, 747, 748, 749, 750, 750, 751, 752,
+	752, 753, 754, 754, 755, 756, 756, 757, 758, 758, 759,
+	760, 760, 761, 762, 762, 763, 764, 764, 765, 765, 766,
+	767, 767, 768, 769, 769, 770, 771, 771, 772, 772, 773,
+	774, 774, 775, 775, 776, 777, 777, 778, 778, 779, 780,
+	780, 781, 781, 782, 783, 783, 784, 784, 785, 785, 786,
+	787, 787, 788, 788, 789, 789, 790, 791, 791, 792, 792,
+	793, 793, 794, 794, 795, 796, 796, 797, 797, 798, 798,
+	799, 799, 800, 800, 801, 801, 802, 803, 803, 804, 804,
+	805, 805, 806, 806, 807, 807, 808, 808, 809, 809, 810,
+	810, 811, 811, 812, 812, 813, 813, 814, 814, 815, 815,
+	816, 816, 817, 817, 818, 818, 819, 819, 820, 820, 821,
+	821, 822, 822, 823, 823, 824, 824, 825, 825, 825, 826,
+	826, 827, 827, 828, 828, 829, 829, 830, 830, 831, 831,
+	832, 832, 832, 833, 833, 834, 834, 835, 835, 836, 836,
+	837, 837, 837, 838, 838, 839, 839, 840, 840, 841, 841,
+	841, 842, 842, 843, 843, 844, 844, 844, 845, 845, 846,
+	846, 847, 847, 847, 848, 848, 849, 849, 850, 850, 850,
+	851, 851, 852, 852, 852, 853, 853, 854, 854, 855, 855,
+	855, 856, 856, 857, 857, 857, 858, 858, 859, 859, 859,
+	860, 860, 861, 861, 861, 862, 862, 863, 863, 863, 864,
+	864, 865, 865, 865, 866, 866, 866, 867, 867, 868, 868,
+	868, 869, 869, 870, 870, 870, 871, 871, 871, 872, 872,
+	873, 873, 873, 874, 874, 875, 875, 875, 876, 876, 876,
+	877, 877, 877, 878, 878, 879, 879, 879, 880, 880, 880,
+	881, 881, 882, 882, 882, 883, 883, 883, 884, 884, 884,
+	885, 885, 885, 886, 886, 887, 887, 887, 888, 888, 888,
+	889, 889, 889, 890, 890, 890, 891, 891, 891, 892, 892,
+	892, 893, 893, 894, 894, 894, 895, 895, 895, 896, 896,
+	896, 897, 897, 897, 898, 898, 898, 899, 899, 899, 900,
+	900, 900, 901, 901, 901, 902, 902, 902, 903, 903, 903,
+	904, 904, 904, 905, 905, 905, 906, 906, 906, 907, 907,
+	907, 908, 908, 908, 908, 909, 909, 909, 910, 910, 910,
+	911, 911, 911, 912, 912, 912, 913, 913, 913, 914, 914,
+	914, 914, 915, 915, 915, 916, 916, 916, 917, 917, 917,
+	918, 918, 918, 919, 919, 919, 919, 920, 920, 920, 921,
+	921, 921, 922, 922, 922, 923, 923, 923, 923, 924, 924,
+	924, 925, 925, 925, 926, 926, 926, 926, 927, 927, 927,
+	928, 928, 928, 928, 929, 929, 929, 930, 930, 930, 931,
+	931, 931, 931, 932, 932, 932, 933, 933, 933, 933, 934,
+	934, 934, 935, 935, 935, 935, 936, 936, 936, 937, 937,
+	937, 937, 938, 938, 938, 939, 939, 939, 939, 940, 940,
+	940, 941, 941, 941, 941, 942, 942, 942, 942, 943, 943,
+	943, 944, 944, 944, 944, 945, 945, 945, 946, 946, 946,
+	946, 947, 947, 947, 947, 948, 948, 948, 949, 949, 949,
+	949, 950, 950, 950, 950, 951, 951, 951, 951, 952, 952,
+	952, 953, 953, 953, 953, 954, 954, 954, 954, 955, 955,
+	955, 955, 956, 956, 956, 956, 957, 957, 957, 958, 958,
+	958, 958, 959, 959, 959, 959, 960, 960, 960, 960, 961,
+	961, 961, 961, 962, 962, 962, 962, 963, 963, 963, 963,
+	964, 964, 964, 964, 965, 965, 965, 965, 966, 966, 966,
+	966, 967, 967, 967, 967, 968, 968, 968, 968, 969, 969,
+	969, 969, 970, 970, 970, 970, 971, 971, 971, 971, 972,
+	972, 972, 972, 973, 973, 973, 973, 974, 974, 974, 974,
+	975, 975, 975, 975, 976, 976, 976, 976, 977, 977, 977,
+	977, 978, 978, 978, 978, 978, 979, 979, 979, 979, 980,
+	980, 980, 980, 981, 981, 981, 981, 982, 982, 982, 982,
+	983, 983, 983, 983, 983, 984, 984, 984, 984, 985, 985,
+	985, 985, 986, 986, 986, 986, 986, 987, 987, 987, 987,
+	988, 988, 988, 988, 989, 989, 989, 989, 989, 990, 990,
+	990, 990, 991, 991, 991, 991, 992, 992, 992, 992, 992,
+	993, 993, 993, 993, 994, 994, 994, 994, 994, 995, 995,
+	995, 995, 996, 996, 996, 996, 996, 997, 997, 997, 997,
+	998, 998, 998, 998, 998, 999, 999, 999, 999, 1000, 1000,
+	1000, 1000, 1000, 1001, 1001, 1001, 1001, 1002, 1002, 1002, 1002,
+	1002, 1003, 1003, 1003, 1003, 1003, 1004, 1004, 1004, 1004, 1005,
+	1005, 1005, 1005, 1005, 1006, 1006, 1006, 1006, 1006, 1007, 1007,
+	1007, 1007, 1008, 1008, 1008, 1008, 1008, 1009, 1009, 1009, 1009,
+	1009, 1010, 1010, 1010, 1010, 1010, 1011, 1011, 1011, 1011, 1012,
+	1012, 1012, 1012, 1012, 1013, 1013, 1013, 1013, 1013, 1014, 1014,
+	1014, 1014, 1014, 1015, 1015, 1015, 1015, 1015, 1016, 1016, 1016,
+	1016, 1017, 1017, 1017, 1017, 1017, 1018, 1018, 1018, 1018, 1018,
+	1019, 1019, 1019, 1019, 1019, 1020, 1020, 1020, 1020, 1020, 1021,
+	1021, 1021, 1021, 1021, 1022, 1022, 1022, 1022, 1022, 1023, 1023,
+	1023,
+};
+
+static const u16 xgamma10_03[GAMMA10_TABLE_LENGTH] = {
+	0, 128, 157, 178, 194, 207, 219, 229, 239, 247, 255,
+	263, 270, 276, 282, 288, 294, 299, 304, 309, 314, 319,
+	323, 328, 332, 336, 340, 344, 348, 351, 355, 358, 362,
+	365, 368, 372, 375, 378, 381, 384, 387, 390, 393, 395,
+	398, 401, 403, 406, 409, 411, 414, 416, 419, 421, 423,
+	426, 428, 430, 432, 435, 437, 439, 441, 443, 445, 447,
+	450, 452, 454, 456, 458, 460, 461, 463, 465, 467, 469,
+	471, 473, 474, 476, 478, 480, 482, 483, 485, 487, 488,
+	490, 492, 493, 495, 497, 498, 500, 501, 503, 505, 506,
+	508, 509, 511, 512, 514, 515, 517, 518, 520, 521, 523,
+	524, 525, 527, 528, 530, 531, 532, 534, 535, 537, 538,
+	539, 541, 542, 543, 544, 546, 547, 548, 550, 551, 552,
+	553, 555, 556, 557, 558, 560, 561, 562, 563, 565, 566,
+	567, 568, 569, 570, 572, 573, 574, 575, 576, 577, 579,
+	580, 581, 582, 583, 584, 585, 586, 587, 589, 590, 591,
+	592, 593, 594, 595, 596, 597, 598, 599, 600, 601, 602,
+	603, 604, 605, 606, 607, 608, 609, 610, 611, 612, 613,
+	614, 615, 616, 617, 618, 619, 620, 621, 622, 623, 624,
+	625, 626, 627, 628, 629, 630, 631, 632, 633, 633, 634,
+	635, 636, 637, 638, 639, 640, 641, 642, 642, 643, 644,
+	645, 646, 647, 648, 649, 649, 650, 651, 652, 653, 654,
+	655, 655, 656, 657, 658, 659, 660, 661, 661, 662, 663,
+	664, 665, 665, 666, 667, 668, 669, 670, 670, 671, 672,
+	673, 674, 674, 675, 676, 677, 677, 678, 679, 680, 681,
+	681, 682, 683, 684, 684, 685, 686, 687, 688, 688, 689,
+	690, 691, 691, 692, 693, 694, 694, 695, 696, 696, 697,
+	698, 699, 699, 700, 701, 702, 702, 703, 704, 704, 705,
+	706, 707, 707, 708, 709, 709, 710, 711, 712, 712, 713,
+	714, 714, 715, 716, 716, 717, 718, 718, 719, 720, 721,
+	721, 722, 723, 723, 724, 725, 725, 726, 727, 727, 728,
+	729, 729, 730, 731, 731, 732, 733, 733, 734, 734, 735,
+	736, 736, 737, 738, 738, 739, 740, 740, 741, 742, 742,
+	743, 743, 744, 745, 745, 746, 747, 747, 748, 748, 749,
+	750, 750, 751, 752, 752, 753, 753, 754, 755, 755, 756,
+	756, 757, 758, 758, 759, 759, 760, 761, 761, 762, 762,
+	763, 764, 764, 765, 765, 766, 767, 767, 768, 768, 769,
+	770, 770, 771, 771, 772, 772, 773, 774, 774, 775, 775,
+	776, 776, 777, 778, 778, 779, 779, 780, 780, 781, 782,
+	782, 783, 783, 784, 784, 785, 785, 786, 787, 787, 788,
+	788, 789, 789, 790, 790, 791, 792, 792, 793, 793, 794,
+	794, 795, 795, 796, 796, 797, 797, 798, 799, 799, 800,
+	800, 801, 801, 802, 802, 803, 803, 804, 804, 805, 805,
+	806, 806, 807, 808, 808, 809, 809, 810, 810, 811, 811,
+	812, 812, 813, 813, 814, 814, 815, 815, 816, 816, 817,
+	817, 818, 818, 819, 819, 820, 820, 821, 821, 822, 822,
+	823, 823, 824, 824, 825, 825, 826, 826, 827, 827, 828,
+	828, 829, 829, 830, 830, 831, 831, 832, 832, 833, 833,
+	834, 834, 835, 835, 836, 836, 836, 837, 837, 838, 838,
+	839, 839, 840, 840, 841, 841, 842, 842, 843, 843, 844,
+	844, 845, 845, 845, 846, 846, 847, 847, 848, 848, 849,
+	849, 850, 850, 851, 851, 852, 852, 852, 853, 853, 854,
+	854, 855, 855, 856, 856, 857, 857, 857, 858, 858, 859,
+	859, 860, 860, 861, 861, 862, 862, 862, 863, 863, 864,
+	864, 865, 865, 866, 866, 866, 867, 867, 868, 868, 869,
+	869, 869, 870, 870, 871, 871, 872, 872, 873, 873, 873,
+	874, 874, 875, 875, 876, 876, 876, 877, 877, 878, 878,
+	879, 879, 879, 880, 880, 881, 881, 882, 882, 882, 883,
+	883, 884, 884, 885, 885, 885, 886, 886, 887, 887, 887,
+	888, 888, 889, 889, 890, 890, 890, 891, 891, 892, 892,
+	892, 893, 893, 894, 894, 895, 895, 895, 896, 896, 897,
+	897, 897, 898, 898, 899, 899, 899, 900, 900, 901, 901,
+	901, 902, 902, 903, 903, 903, 904, 904, 905, 905, 905,
+	906, 906, 907, 907, 907, 908, 908, 909, 909, 909, 910,
+	910, 911, 911, 911, 912, 912, 913, 913, 913, 914, 914,
+	915, 915, 915, 916, 916, 916, 917, 917, 918, 918, 918,
+	919, 919, 920, 920, 920, 921, 921, 921, 922, 922, 923,
+	923, 923, 924, 924, 925, 925, 925, 926, 926, 926, 927,
+	927, 928, 928, 928, 929, 929, 929, 930, 930, 931, 931,
+	931, 932, 932, 932, 933, 933, 934, 934, 934, 935, 935,
+	935, 936, 936, 936, 937, 937, 938, 938, 938, 939, 939,
+	939, 940, 940, 941, 941, 941, 942, 942, 942, 943, 943,
+	943, 944, 944, 945, 945, 945, 946, 946, 946, 947, 947,
+	947, 948, 948, 948, 949, 949, 950, 950, 950, 951, 951,
+	951, 952, 952, 952, 953, 953, 953, 954, 954, 955, 955,
+	955, 956, 956, 956, 957, 957, 957, 958, 958, 958, 959,
+	959, 959, 960, 960, 960, 961, 961, 962, 962, 962, 963,
+	963, 963, 964, 964, 964, 965, 965, 965, 966, 966, 966,
+	967, 967, 967, 968, 968, 968, 969, 969, 969, 970, 970,
+	970, 971, 971, 971, 972, 972, 972, 973, 973, 973, 974,
+	974, 974, 975, 975, 975, 976, 976, 976, 977, 977, 977,
+	978, 978, 978, 979, 979, 979, 980, 980, 980, 981, 981,
+	981, 982, 982, 982, 983, 983, 983, 984, 984, 984, 985,
+	985, 985, 986, 986, 986, 987, 987, 987, 988, 988, 988,
+	989, 989, 989, 990, 990, 990, 991, 991, 991, 992, 992,
+	992, 993, 993, 993, 994, 994, 994, 994, 995, 995, 995,
+	996, 996, 996, 997, 997, 997, 998, 998, 998, 999, 999,
+	999, 1000, 1000, 1000, 1001, 1001, 1001, 1001, 1002, 1002, 1002,
+	1003, 1003, 1003, 1004, 1004, 1004, 1005, 1005, 1005, 1006, 1006,
+	1006, 1006, 1007, 1007, 1007, 1008, 1008, 1008, 1009, 1009, 1009,
+	1010, 1010, 1010, 1011, 1011, 1011, 1011, 1012, 1012, 1012, 1013,
+	1013, 1013, 1014, 1014, 1014, 1015, 1015, 1015, 1015, 1016, 1016,
+	1016, 1017, 1017, 1017, 1018, 1018, 1018, 1018, 1019, 1019, 1019,
+	1020, 1020, 1020, 1021, 1021, 1021, 1021, 1022, 1022, 1022, 1023,
+	1023,
+};
+
+static const u16 xgamma10_04[GAMMA10_TABLE_LENGTH] = {
+	0, 64, 84, 99, 111, 122, 131, 139, 147, 154, 161,
+	167, 173, 178, 184, 189, 194, 199, 203, 208, 212, 216,
+	220, 224, 228, 232, 235, 239, 243, 246, 249, 253, 256,
+	259, 262, 265, 268, 271, 274, 277, 280, 283, 285, 288,
+	291, 293, 296, 298, 301, 303, 306, 308, 311, 313, 315,
+	318, 320, 322, 325, 327, 329, 331, 333, 335, 338, 340,
+	342, 344, 346, 348, 350, 352, 354, 356, 358, 360, 362,
+	364, 365, 367, 369, 371, 373, 375, 376, 378, 380, 382,
+	383, 385, 387, 389, 390, 392, 394, 395, 397, 399, 400,
+	402, 404, 405, 407, 408, 410, 412, 413, 415, 416, 418,
+	419, 421, 422, 424, 425, 427, 428, 430, 431, 433, 434,
+	436, 437, 438, 440, 441, 443, 444, 445, 447, 448, 450,
+	451, 452, 454, 455, 456, 458, 459, 460, 462, 463, 464,
+	466, 467, 468, 470, 471, 472, 473, 475, 476, 477, 478,
+	480, 481, 482, 483, 485, 486, 487, 488, 489, 491, 492,
+	493, 494, 495, 497, 498, 499, 500, 501, 503, 504, 505,
+	506, 507, 508, 509, 511, 512, 513, 514, 515, 516, 517,
+	518, 520, 521, 522, 523, 524, 525, 526, 527, 528, 529,
+	530, 531, 533, 534, 535, 536, 537, 538, 539, 540, 541,
+	542, 543, 544, 545, 546, 547, 548, 549, 550, 551, 552,
+	553, 554, 555, 556, 557, 558, 559, 560, 561, 562, 563,
+	564, 565, 566, 567, 568, 569, 570, 571, 572, 573, 574,
+	575, 576, 577, 578, 578, 579, 580, 581, 582, 583, 584,
+	585, 586, 587, 588, 589, 590, 591, 591, 592, 593, 594,
+	595, 596, 597, 598, 599, 600, 600, 601, 602, 603, 604,
+	605, 606, 607, 607, 608, 609, 610, 611, 612, 613, 614,
+	614, 615, 616, 617, 618, 619, 620, 620, 621, 622, 623,
+	624, 625, 625, 626, 627, 628, 629, 630, 630, 631, 632,
+	633, 634, 635, 635, 636, 637, 638, 639, 639, 640, 641,
+	642, 643, 643, 644, 645, 646, 647, 647, 648, 649, 650,
+	651, 651, 652, 653, 654, 655, 655, 656, 657, 658, 658,
+	659, 660, 661, 662, 662, 663, 664, 665, 665, 666, 667,
+	668, 668, 669, 670, 671, 671, 672, 673, 674, 674, 675,
+	676, 677, 677, 678, 679, 680, 680, 681, 682, 683, 683,
+	684, 685, 685, 686, 687, 688, 688, 689, 690, 691, 691,
+	692, 693, 693, 694, 695, 696, 696, 697, 698, 698, 699,
+	700, 701, 701, 702, 703, 703, 704, 705, 705, 706, 707,
+	708, 708, 709, 710, 710, 711, 712, 712, 713, 714, 714,
+	715, 716, 717, 717, 718, 719, 719, 720, 721, 721, 722,
+	723, 723, 724, 725, 725, 726, 727, 727, 728, 729, 729,
+	730, 731, 731, 732, 733, 733, 734, 735, 735, 736, 737,
+	737, 738, 739, 739, 740, 740, 741, 742, 742, 743, 744,
+	744, 745, 746, 746, 747, 748, 748, 749, 749, 750, 751,
+	751, 752, 753, 753, 754, 755, 755, 756, 756, 757, 758,
+	758, 759, 760, 760, 761, 761, 762, 763, 763, 764, 765,
+	765, 766, 766, 767, 768, 768, 769, 769, 770, 771, 771,
+	772, 773, 773, 774, 774, 775, 776, 776, 777, 777, 778,
+	779, 779, 780, 780, 781, 782, 782, 783, 783, 784, 785,
+	785, 786, 786, 787, 788, 788, 789, 789, 790, 791, 791,
+	792, 792, 793, 793, 794, 795, 795, 796, 796, 797, 798,
+	798, 799, 799, 800, 800, 801, 802, 802, 803, 803, 804,
+	804, 805, 806, 806, 807, 807, 808, 808, 809, 810, 810,
+	811, 811, 812, 812, 813, 814, 814, 815, 815, 816, 816,
+	817, 818, 818, 819, 819, 820, 820, 821, 821, 822, 823,
+	823, 824, 824, 825, 825, 826, 826, 827, 827, 828, 829,
+	829, 830, 830, 831, 831, 832, 832, 833, 834, 834, 835,
+	835, 836, 836, 837, 837, 838, 838, 839, 839, 840, 841,
+	841, 842, 842, 843, 843, 844, 844, 845, 845, 846, 846,
+	847, 847, 848, 849, 849, 850, 850, 851, 851, 852, 852,
+	853, 853, 854, 854, 855, 855, 856, 856, 857, 857, 858,
+	859, 859, 860, 860, 861, 861, 862, 862, 863, 863, 864,
+	864, 865, 865, 866, 866, 867, 867, 868, 868, 869, 869,
+	870, 870, 871, 871, 872, 872, 873, 873, 874, 874, 875,
+	875, 876, 876, 877, 877, 878, 878, 879, 879, 880, 880,
+	881, 881, 882, 882, 883, 883, 884, 884, 885, 885, 886,
+	886, 887, 887, 888, 888, 889, 889, 890, 890, 891, 891,
+	892, 892, 893, 893, 894, 894, 895, 895, 896, 896, 897,
+	897, 898, 898, 899, 899, 900, 900, 901, 901, 902, 902,
+	903, 903, 904, 904, 905, 905, 905, 906, 906, 907, 907,
+	908, 908, 909, 909, 910, 910, 911, 911, 912, 912, 913,
+	913, 914, 914, 915, 915, 915, 916, 916, 917, 917, 918,
+	918, 919, 919, 920, 920, 921, 921, 922, 922, 923, 923,
+	923, 924, 924, 925, 925, 926, 926, 927, 927, 928, 928,
+	929, 929, 929, 930, 930, 931, 931, 932, 932, 933, 933,
+	934, 934, 935, 935, 935, 936, 936, 937, 937, 938, 938,
+	939, 939, 940, 940, 940, 941, 941, 942, 942, 943, 943,
+	944, 944, 945, 945, 945, 946, 946, 947, 947, 948, 948,
+	949, 949, 949, 950, 950, 951, 951, 952, 952, 953, 953,
+	953, 954, 954, 955, 955, 956, 956, 957, 957, 957, 958,
+	958, 959, 959, 960, 960, 961, 961, 961, 962, 962, 963,
+	963, 964, 964, 965, 965, 965, 966, 966, 967, 967, 968,
+	968, 968, 969, 969, 970, 970, 971, 971, 971, 972, 972,
+	973, 973, 974, 974, 974, 975, 975, 976, 976, 977, 977,
+	977, 978, 978, 979, 979, 980, 980, 980, 981, 981, 982,
+	982, 983, 983, 983, 984, 984, 985, 985, 986, 986, 986,
+	987, 987, 988, 988, 989, 989, 989, 990, 990, 991, 991,
+	991, 992, 992, 993, 993, 994, 994, 994, 995, 995, 996,
+	996, 996, 997, 997, 998, 998, 999, 999, 999, 1000, 1000,
+	1001, 1001, 1001, 1002, 1002, 1003, 1003, 1004, 1004, 1004, 1005,
+	1005, 1006, 1006, 1006, 1007, 1007, 1008, 1008, 1008, 1009, 1009,
+	1010, 1010, 1010, 1011, 1011, 1012, 1012, 1013, 1013, 1013, 1014,
+	1014, 1015, 1015, 1015, 1016, 1016, 1017, 1017, 1017, 1018, 1018,
+	1019, 1019, 1019, 1020, 1020, 1021, 1021, 1021, 1022, 1022, 1023,
+	1023,
+};
+
+static const u16 xgamma10_05[GAMMA10_TABLE_LENGTH] = {
+	0, 32, 45, 55, 64, 72, 78, 85, 90, 96, 101,
+	106, 111, 115, 120, 124, 128, 132, 136, 139, 143, 147,
+	150, 153, 157, 160, 163, 166, 169, 172, 175, 178, 181,
+	184, 186, 189, 192, 195, 197, 200, 202, 205, 207, 210,
+	212, 215, 217, 219, 222, 224, 226, 228, 231, 233, 235,
+	237, 239, 241, 244, 246, 248, 250, 252, 254, 256, 258,
+	260, 262, 264, 266, 268, 270, 271, 273, 275, 277, 279,
+	281, 282, 284, 286, 288, 290, 291, 293, 295, 297, 298,
+	300, 302, 303, 305, 307, 308, 310, 312, 313, 315, 317,
+	318, 320, 321, 323, 325, 326, 328, 329, 331, 332, 334,
+	335, 337, 338, 340, 341, 343, 344, 346, 347, 349, 350,
+	352, 353, 355, 356, 358, 359, 360, 362, 363, 365, 366,
+	367, 369, 370, 372, 373, 374, 376, 377, 378, 380, 381,
+	382, 384, 385, 386, 388, 389, 390, 392, 393, 394, 396,
+	397, 398, 399, 401, 402, 403, 405, 406, 407, 408, 410,
+	411, 412, 413, 415, 416, 417, 418, 419, 421, 422, 423,
+	424, 426, 427, 428, 429, 430, 431, 433, 434, 435, 436,
+	437, 439, 440, 441, 442, 443, 444, 445, 447, 448, 449,
+	450, 451, 452, 453, 455, 456, 457, 458, 459, 460, 461,
+	462, 463, 465, 466, 467, 468, 469, 470, 471, 472, 473,
+	474, 475, 477, 478, 479, 480, 481, 482, 483, 484, 485,
+	486, 487, 488, 489, 490, 491, 492, 493, 494, 495, 497,
+	498, 499, 500, 501, 502, 503, 504, 505, 506, 507, 508,
+	509, 510, 511, 512, 513, 514, 515, 516, 517, 518, 519,
+	520, 521, 522, 523, 524, 525, 526, 527, 527, 528, 529,
+	530, 531, 532, 533, 534, 535, 536, 537, 538, 539, 540,
+	541, 542, 543, 544, 545, 546, 547, 547, 548, 549, 550,
+	551, 552, 553, 554, 555, 556, 557, 558, 559, 559, 560,
+	561, 562, 563, 564, 565, 566, 567, 568, 569, 569, 570,
+	571, 572, 573, 574, 575, 576, 577, 577, 578, 579, 580,
+	581, 582, 583, 584, 585, 585, 586, 587, 588, 589, 590,
+	591, 591, 592, 593, 594, 595, 596, 597, 598, 598, 599,
+	600, 601, 602, 603, 603, 604, 605, 606, 607, 608, 609,
+	609, 610, 611, 612, 613, 614, 614, 615, 616, 617, 618,
+	619, 619, 620, 621, 622, 623, 623, 624, 625, 626, 627,
+	628, 628, 629, 630, 631, 632, 632, 633, 634, 635, 636,
+	636, 637, 638, 639, 640, 640, 641, 642, 643, 644, 644,
+	645, 646, 647, 648, 648, 649, 650, 651, 652, 652, 653,
+	654, 655, 655, 656, 657, 658, 659, 659, 660, 661, 662,
+	662, 663, 664, 665, 666, 666, 667, 668, 669, 669, 670,
+	671, 672, 672, 673, 674, 675, 675, 676, 677, 678, 678,
+	679, 680, 681, 681, 682, 683, 684, 684, 685, 686, 687,
+	687, 688, 689, 690, 690, 691, 692, 693, 693, 694, 695,
+	696, 696, 697, 698, 699, 699, 700, 701, 701, 702, 703,
+	704, 704, 705, 706, 707, 707, 708, 709, 709, 710, 711,
+	712, 712, 713, 714, 714, 715, 716, 717, 717, 718, 719,
+	719, 720, 721, 722, 722, 723, 724, 724, 725, 726, 727,
+	727, 728, 729, 729, 730, 731, 731, 732, 733, 734, 734,
+	735, 736, 736, 737, 738, 738, 739, 740, 740, 741, 742,
+	743, 743, 744, 745, 745, 746, 747, 747, 748, 749, 749,
+	750, 751, 751, 752, 753, 754, 754, 755, 756, 756, 757,
+	758, 758, 759, 760, 760, 761, 762, 762, 763, 764, 764,
+	765, 766, 766, 767, 768, 768, 769, 770, 770, 771, 772,
+	772, 773, 774, 774, 775, 776, 776, 777, 778, 778, 779,
+	780, 780, 781, 781, 782, 783, 783, 784, 785, 785, 786,
+	787, 787, 788, 789, 789, 790, 791, 791, 792, 793, 793,
+	794, 794, 795, 796, 796, 797, 798, 798, 799, 800, 800,
+	801, 802, 802, 803, 803, 804, 805, 805, 806, 807, 807,
+	808, 809, 809, 810, 810, 811, 812, 812, 813, 814, 814,
+	815, 815, 816, 817, 817, 818, 819, 819, 820, 820, 821,
+	822, 822, 823, 824, 824, 825, 825, 826, 827, 827, 828,
+	829, 829, 830, 830, 831, 832, 832, 833, 833, 834, 835,
+	835, 836, 836, 837, 838, 838, 839, 840, 840, 841, 841,
+	842, 843, 843, 844, 844, 845, 846, 846, 847, 847, 848,
+	849, 849, 850, 850, 851, 852, 852, 853, 853, 854, 855,
+	855, 856, 856, 857, 858, 858, 859, 859, 860, 861, 861,
+	862, 862, 863, 864, 864, 865, 865, 866, 867, 867, 868,
+	868, 869, 869, 870, 871, 871, 872, 872, 873, 874, 874,
+	875, 875, 876, 877, 877, 878, 878, 879, 879, 880, 881,
+	881, 882, 882, 883, 883, 884, 885, 885, 886, 886, 887,
+	888, 888, 889, 889, 890, 890, 891, 892, 892, 893, 893,
+	894, 894, 895, 896, 896, 897, 897, 898, 898, 899, 900,
+	900, 901, 901, 902, 902, 903, 904, 904, 905, 905, 906,
+	906, 907, 907, 908, 909, 909, 910, 910, 911, 911, 912,
+	913, 913, 914, 914, 915, 915, 916, 916, 917, 918, 918,
+	919, 919, 920, 920, 921, 921, 922, 923, 923, 924, 924,
+	925, 925, 926, 926, 927, 928, 928, 929, 929, 930, 930,
+	931, 931, 932, 932, 933, 934, 934, 935, 935, 936, 936,
+	937, 937, 938, 939, 939, 940, 940, 941, 941, 942, 942,
+	943, 943, 944, 944, 945, 946, 946, 947, 947, 948, 948,
+	949, 949, 950, 950, 951, 952, 952, 953, 953, 954, 954,
+	955, 955, 956, 956, 957, 957, 958, 958, 959, 960, 960,
+	961, 961, 962, 962, 963, 963, 964, 964, 965, 965, 966,
+	966, 967, 967, 968, 969, 969, 970, 970, 971, 971, 972,
+	972, 973, 973, 974, 974, 975, 975, 976, 976, 977, 977,
+	978, 979, 979, 980, 980, 981, 981, 982, 982, 983, 983,
+	984, 984, 985, 985, 986, 986, 987, 987, 988, 988, 989,
+	989, 990, 990, 991, 992, 992, 993, 993, 994, 994, 995,
+	995, 996, 996, 997, 997, 998, 998, 999, 999, 1000, 1000,
+	1001, 1001, 1002, 1002, 1003, 1003, 1004, 1004, 1005, 1005, 1006,
+	1006, 1007, 1007, 1008, 1008, 1009, 1009, 1010, 1010, 1011, 1011,
+	1012, 1012, 1013, 1013, 1014, 1014, 1015, 1015, 1016, 1016, 1017,
+	1017, 1018, 1018, 1019, 1019, 1020, 1020, 1021, 1021, 1022, 1022,
+	1023,
+};
+
+static const u16 xgamma10_06[GAMMA10_TABLE_LENGTH] = {
+	0, 16, 24, 31, 37, 42, 47, 51, 56, 60, 64,
+	67, 71, 75, 78, 81, 84, 88, 91, 94, 97, 99,
+	102, 105, 108, 110, 113, 116, 118, 121, 123, 126, 128,
+	130, 133, 135, 137, 140, 142, 144, 146, 148, 151, 153,
+	155, 157, 159, 161, 163, 165, 167, 169, 171, 173, 175,
+	177, 179, 181, 183, 185, 187, 188, 190, 192, 194, 196,
+	198, 199, 201, 203, 205, 206, 208, 210, 212, 213, 215,
+	217, 218, 220, 222, 223, 225, 227, 228, 230, 232, 233,
+	235, 236, 238, 240, 241, 243, 244, 246, 247, 249, 250,
+	252, 253, 255, 257, 258, 260, 261, 263, 264, 265, 267,
+	268, 270, 271, 273, 274, 276, 277, 279, 280, 281, 283,
+	284, 286, 287, 288, 290, 291, 293, 294, 295, 297, 298,
+	299, 301, 302, 303, 305, 306, 308, 309, 310, 312, 313,
+	314, 315, 317, 318, 319, 321, 322, 323, 325, 326, 327,
+	328, 330, 331, 332, 334, 335, 336, 337, 339, 340, 341,
+	342, 344, 345, 346, 347, 349, 350, 351, 352, 353, 355,
+	356, 357, 358, 359, 361, 362, 363, 364, 365, 367, 368,
+	369, 370, 371, 373, 374, 375, 376, 377, 378, 380, 381,
+	382, 383, 384, 385, 387, 388, 389, 390, 391, 392, 393,
+	394, 396, 397, 398, 399, 400, 401, 402, 403, 405, 406,
+	407, 408, 409, 410, 411, 412, 413, 415, 416, 417, 418,
+	419, 420, 421, 422, 423, 424, 425, 426, 428, 429, 430,
+	431, 432, 433, 434, 435, 436, 437, 438, 439, 440, 441,
+	442, 443, 445, 446, 447, 448, 449, 450, 451, 452, 453,
+	454, 455, 456, 457, 458, 459, 460, 461, 462, 463, 464,
+	465, 466, 467, 468, 469, 470, 471, 472, 473, 474, 475,
+	476, 477, 478, 479, 480, 481, 482, 483, 484, 485, 486,
+	487, 488, 489, 490, 491, 492, 493, 494, 495, 496, 497,
+	498, 499, 500, 501, 502, 503, 504, 505, 506, 507, 507,
+	508, 509, 510, 511, 512, 513, 514, 515, 516, 517, 518,
+	519, 520, 521, 522, 523, 524, 525, 525, 526, 527, 528,
+	529, 530, 531, 532, 533, 534, 535, 536, 537, 538, 538,
+	539, 540, 541, 542, 543, 544, 545, 546, 547, 548, 548,
+	549, 550, 551, 552, 553, 554, 555, 556, 557, 558, 558,
+	559, 560, 561, 562, 563, 564, 565, 566, 566, 567, 568,
+	569, 570, 571, 572, 573, 574, 574, 575, 576, 577, 578,
+	579, 580, 581, 581, 582, 583, 584, 585, 586, 587, 588,
+	588, 589, 590, 591, 592, 593, 594, 594, 595, 596, 597,
+	598, 599, 600, 601, 601, 602, 603, 604, 605, 606, 606,
+	607, 608, 609, 610, 611, 612, 612, 613, 614, 615, 616,
+	617, 617, 618, 619, 620, 621, 622, 622, 623, 624, 625,
+	626, 627, 627, 628, 629, 630, 631, 632, 632, 633, 634,
+	635, 636, 637, 637, 638, 639, 640, 641, 642, 642, 643,
+	644, 645, 646, 646, 647, 648, 649, 650, 650, 651, 652,
+	653, 654, 655, 655, 656, 657, 658, 659, 659, 660, 661,
+	662, 663, 663, 664, 665, 666, 667, 667, 668, 669, 670,
+	671, 671, 672, 673, 674, 675, 675, 676, 677, 678, 678,
+	679, 680, 681, 682, 682, 683, 684, 685, 686, 686, 687,
+	688, 689, 689, 690, 691, 692, 693, 693, 694, 695, 696,
+	696, 697, 698, 699, 700, 700, 701, 702, 703, 703, 704,
+	705, 706, 707, 707, 708, 709, 710, 710, 711, 712, 713,
+	713, 714, 715, 716, 716, 717, 718, 719, 719, 720, 721,
+	722, 723, 723, 724, 725, 726, 726, 727, 728, 729, 729,
+	730, 731, 732, 732, 733, 734, 735, 735, 736, 737, 738,
+	738, 739, 740, 741, 741, 742, 743, 743, 744, 745, 746,
+	746, 747, 748, 749, 749, 750, 751, 752, 752, 753, 754,
+	755, 755, 756, 757, 758, 758, 759, 760, 760, 761, 762,
+	763, 763, 764, 765, 766, 766, 767, 768, 768, 769, 770,
+	771, 771, 772, 773, 774, 774, 775, 776, 776, 777, 778,
+	779, 779, 780, 781, 781, 782, 783, 784, 784, 785, 786,
+	786, 787, 788, 789, 789, 790, 791, 791, 792, 793, 794,
+	794, 795, 796, 796, 797, 798, 799, 799, 800, 801, 801,
+	802, 803, 803, 804, 805, 806, 806, 807, 808, 808, 809,
+	810, 811, 811, 812, 813, 813, 814, 815, 815, 816, 817,
+	818, 818, 819, 820, 820, 821, 822, 822, 823, 824, 824,
+	825, 826, 827, 827, 828, 829, 829, 830, 831, 831, 832,
+	833, 833, 834, 835, 835, 836, 837, 838, 838, 839, 840,
+	840, 841, 842, 842, 843, 844, 844, 845, 846, 846, 847,
+	848, 848, 849, 850, 851, 851, 852, 853, 853, 854, 855,
+	855, 856, 857, 857, 858, 859, 859, 860, 861, 861, 862,
+	863, 863, 864, 865, 865, 866, 867, 867, 868, 869, 869,
+	870, 871, 871, 872, 873, 873, 874, 875, 875, 876, 877,
+	877, 878, 879, 879, 880, 881, 881, 882, 883, 883, 884,
+	885, 885, 886, 887, 887, 888, 889, 889, 890, 891, 891,
+	892, 893, 893, 894, 895, 895, 896, 897, 897, 898, 898,
+	899, 900, 900, 901, 902, 902, 903, 904, 904, 905, 906,
+	906, 907, 908, 908, 909, 910, 910, 911, 911, 912, 913,
+	913, 914, 915, 915, 916, 917, 917, 918, 919, 919, 920,
+	921, 921, 922, 922, 923, 924, 924, 925, 926, 926, 927,
+	928, 928, 929, 930, 930, 931, 931, 932, 933, 933, 934,
+	935, 935, 936, 937, 937, 938, 938, 939, 940, 940, 941,
+	942, 942, 943, 944, 944, 945, 945, 946, 947, 947, 948,
+	949, 949, 950, 950, 951, 952, 952, 953, 954, 954, 955,
+	956, 956, 957, 957, 958, 959, 959, 960, 961, 961, 962,
+	962, 963, 964, 964, 965, 966, 966, 967, 967, 968, 969,
+	969, 970, 970, 971, 972, 972, 973, 974, 974, 975, 975,
+	976, 977, 977, 978, 979, 979, 980, 980, 981, 982, 982,
+	983, 983, 984, 985, 985, 986, 987, 987, 988, 988, 989,
+	990, 990, 991, 991, 992, 993, 993, 994, 995, 995, 996,
+	996, 997, 998, 998, 999, 999, 1000, 1001, 1001, 1002, 1002,
+	1003, 1004, 1004, 1005, 1006, 1006, 1007, 1007, 1008, 1009, 1009,
+	1010, 1010, 1011, 1012, 1012, 1013, 1013, 1014, 1015, 1015, 1016,
+	1016, 1017, 1018, 1018, 1019, 1019, 1020, 1021, 1021, 1022, 1022,
+	1023,
+};
+
+static const u16 xgamma10_07[GAMMA10_TABLE_LENGTH] = {
+	0, 8, 13, 17, 21, 25, 28, 31, 34, 37, 40,
+	43, 46, 48, 51, 53, 56, 58, 60, 63, 65, 67,
+	70, 72, 74, 76, 78, 80, 82, 84, 86, 88, 90,
+	92, 94, 96, 98, 100, 102, 104, 106, 108, 109, 111,
+	113, 115, 117, 118, 120, 122, 124, 125, 127, 129, 131,
+	132, 134, 136, 137, 139, 140, 142, 144, 145, 147, 149,
+	150, 152, 153, 155, 157, 158, 160, 161, 163, 164, 166,
+	167, 169, 170, 172, 173, 175, 176, 178, 179, 181, 182,
+	184, 185, 187, 188, 190, 191, 192, 194, 195, 197, 198,
+	199, 201, 202, 204, 205, 206, 208, 209, 211, 212, 213,
+	215, 216, 217, 219, 220, 222, 223, 224, 226, 227, 228,
+	230, 231, 232, 234, 235, 236, 237, 239, 240, 241, 243,
+	244, 245, 247, 248, 249, 250, 252, 253, 254, 256, 257,
+	258, 259, 261, 262, 263, 264, 266, 267, 268, 269, 271,
+	272, 273, 274, 275, 277, 278, 279, 280, 282, 283, 284,
+	285, 286, 288, 289, 290, 291, 292, 294, 295, 296, 297,
+	298, 300, 301, 302, 303, 304, 306, 307, 308, 309, 310,
+	311, 313, 314, 315, 316, 317, 318, 319, 321, 322, 323,
+	324, 325, 326, 327, 329, 330, 331, 332, 333, 334, 335,
+	337, 338, 339, 340, 341, 342, 343, 344, 346, 347, 348,
+	349, 350, 351, 352, 353, 354, 355, 357, 358, 359, 360,
+	361, 362, 363, 364, 365, 366, 368, 369, 370, 371, 372,
+	373, 374, 375, 376, 377, 378, 379, 380, 382, 383, 384,
+	385, 386, 387, 388, 389, 390, 391, 392, 393, 394, 395,
+	396, 397, 398, 400, 401, 402, 403, 404, 405, 406, 407,
+	408, 409, 410, 411, 412, 413, 414, 415, 416, 417, 418,
+	419, 420, 421, 422, 423, 424, 425, 426, 427, 428, 429,
+	430, 431, 432, 433, 434, 435, 436, 437, 439, 440, 441,
+	442, 443, 444, 445, 446, 447, 448, 449, 450, 451, 452,
+	452, 453, 454, 455, 456, 457, 458, 459, 460, 461, 462,
+	463, 464, 465, 466, 467, 468, 469, 470, 471, 472, 473,
+	474, 475, 476, 477, 478, 479, 480, 481, 482, 483, 484,
+	485, 486, 487, 488, 489, 490, 491, 492, 492, 493, 494,
+	495, 496, 497, 498, 499, 500, 501, 502, 503, 504, 505,
+	506, 507, 508, 509, 510, 511, 511, 512, 513, 514, 515,
+	516, 517, 518, 519, 520, 521, 522, 523, 524, 525, 526,
+	526, 527, 528, 529, 530, 531, 532, 533, 534, 535, 536,
+	537, 538, 538, 539, 540, 541, 542, 543, 544, 545, 546,
+	547, 548, 549, 549, 550, 551, 552, 553, 554, 555, 556,
+	557, 558, 559, 560, 560, 561, 562, 563, 564, 565, 566,
+	567, 568, 569, 569, 570, 571, 572, 573, 574, 575, 576,
+	577, 578, 578, 579, 580, 581, 582, 583, 584, 585, 586,
+	586, 587, 588, 589, 590, 591, 592, 593, 594, 594, 595,
+	596, 597, 598, 599, 600, 601, 601, 602, 603, 604, 605,
+	606, 607, 608, 608, 609, 610, 611, 612, 613, 614, 615,
+	615, 616, 617, 618, 619, 620, 621, 622, 622, 623, 624,
+	625, 626, 627, 628, 628, 629, 630, 631, 632, 633, 634,
+	634, 635, 636, 637, 638, 639, 640, 640, 641, 642, 643,
+	644, 645, 646, 646, 647, 648, 649, 650, 651, 652, 652,
+	653, 654, 655, 656, 657, 657, 658, 659, 660, 661, 662,
+	663, 663, 664, 665, 666, 667, 668, 668, 669, 670, 671,
+	672, 673, 673, 674, 675, 676, 677, 678, 678, 679, 680,
+	681, 682, 683, 683, 684, 685, 686, 687, 688, 688, 689,
+	690, 691, 692, 693, 693, 694, 695, 696, 697, 698, 698,
+	699, 700, 701, 702, 703, 703, 704, 705, 706, 707, 707,
+	708, 709, 710, 711, 712, 712, 713, 714, 715, 716, 716,
+	717, 718, 719, 720, 721, 721, 722, 723, 724, 725, 725,
+	726, 727, 728, 729, 729, 730, 731, 732, 733, 733, 734,
+	735, 736, 737, 738, 738, 739, 740, 741, 742, 742, 743,
+	744, 745, 746, 746, 747, 748, 749, 750, 750, 751, 752,
+	753, 754, 754, 755, 756, 757, 758, 758, 759, 760, 761,
+	761, 762, 763, 764, 765, 765, 766, 767, 768, 769, 769,
+	770, 771, 772, 773, 773, 774, 775, 776, 777, 777, 778,
+	779, 780, 780, 781, 782, 783, 784, 784, 785, 786, 787,
+	788, 788, 789, 790, 791, 791, 792, 793, 794, 795, 795,
+	796, 797, 798, 798, 799, 800, 801, 802, 802, 803, 804,
+	805, 805, 806, 807, 808, 809, 809, 810, 811, 812, 812,
+	813, 814, 815, 816, 816, 817, 818, 819, 819, 820, 821,
+	822, 822, 823, 824, 825, 826, 826, 827, 828, 829, 829,
+	830, 831, 832, 832, 833, 834, 835, 835, 836, 837, 838,
+	839, 839, 840, 841, 842, 842, 843, 844, 845, 845, 846,
+	847, 848, 848, 849, 850, 851, 851, 852, 853, 854, 854,
+	855, 856, 857, 857, 858, 859, 860, 860, 861, 862, 863,
+	864, 864, 865, 866, 867, 867, 868, 869, 870, 870, 871,
+	872, 873, 873, 874, 875, 876, 876, 877, 878, 879, 879,
+	880, 881, 881, 882, 883, 884, 884, 885, 886, 887, 887,
+	888, 889, 890, 890, 891, 892, 893, 893, 894, 895, 896,
+	896, 897, 898, 899, 899, 900, 901, 902, 902, 903, 904,
+	904, 905, 906, 907, 907, 908, 909, 910, 910, 911, 912,
+	913, 913, 914, 915, 916, 916, 917, 918, 918, 919, 920,
+	921, 921, 922, 923, 924, 924, 925, 926, 927, 927, 928,
+	929, 929, 930, 931, 932, 932, 933, 934, 935, 935, 936,
+	937, 937, 938, 939, 940, 940, 941, 942, 943, 943, 944,
+	945, 945, 946, 947, 948, 948, 949, 950, 950, 951, 952,
+	953, 953, 954, 955, 956, 956, 957, 958, 958, 959, 960,
+	961, 961, 962, 963, 963, 964, 965, 966, 966, 967, 968,
+	968, 969, 970, 971, 971, 972, 973, 973, 974, 975, 976,
+	976, 977, 978, 978, 979, 980, 981, 981, 982, 983, 983,
+	984, 985, 986, 986, 987, 988, 988, 989, 990, 991, 991,
+	992, 993, 993, 994, 995, 996, 996, 997, 998, 998, 999,
+	1000, 1000, 1001, 1002, 1003, 1003, 1004, 1005, 1005, 1006, 1007,
+	1008, 1008, 1009, 1010, 1010, 1011, 1012, 1012, 1013, 1014, 1015,
+	1015, 1016, 1017, 1017, 1018, 1019, 1019, 1020, 1021, 1022, 1022,
+	1023,
+};
+
+static const u16 xgamma10_08[GAMMA10_TABLE_LENGTH] = {
+	0, 4, 7, 10, 12, 14, 17, 19, 21, 23, 25,
+	27, 29, 31, 33, 35, 37, 39, 40, 42, 44, 46,
+	47, 49, 51, 53, 54, 56, 58, 59, 61, 62, 64,
+	66, 67, 69, 70, 72, 73, 75, 76, 78, 80, 81,
+	83, 84, 86, 87, 89, 90, 91, 93, 94, 96, 97,
+	99, 100, 102, 103, 104, 106, 107, 109, 110, 111, 113,
+	114, 116, 117, 118, 120, 121, 122, 124, 125, 126, 128,
+	129, 131, 132, 133, 135, 136, 137, 138, 140, 141, 142,
+	144, 145, 146, 148, 149, 150, 152, 153, 154, 155, 157,
+	158, 159, 160, 162, 163, 164, 166, 167, 168, 169, 171,
+	172, 173, 174, 176, 177, 178, 179, 181, 182, 183, 184,
+	185, 187, 188, 189, 190, 192, 193, 194, 195, 196, 198,
+	199, 200, 201, 202, 204, 205, 206, 207, 208, 210, 211,
+	212, 213, 214, 216, 217, 218, 219, 220, 221, 223, 224,
+	225, 226, 227, 228, 230, 231, 232, 233, 234, 235, 237,
+	238, 239, 240, 241, 242, 243, 245, 246, 247, 248, 249,
+	250, 251, 253, 254, 255, 256, 257, 258, 259, 260, 262,
+	263, 264, 265, 266, 267, 268, 269, 271, 272, 273, 274,
+	275, 276, 277, 278, 279, 281, 282, 283, 284, 285, 286,
+	287, 288, 289, 290, 292, 293, 294, 295, 296, 297, 298,
+	299, 300, 301, 302, 304, 305, 306, 307, 308, 309, 310,
+	311, 312, 313, 314, 315, 316, 318, 319, 320, 321, 322,
+	323, 324, 325, 326, 327, 328, 329, 330, 331, 332, 333,
+	335, 336, 337, 338, 339, 340, 341, 342, 343, 344, 345,
+	346, 347, 348, 349, 350, 351, 352, 353, 355, 356, 357,
+	358, 359, 360, 361, 362, 363, 364, 365, 366, 367, 368,
+	369, 370, 371, 372, 373, 374, 375, 376, 377, 378, 379,
+	380, 381, 382, 383, 384, 385, 386, 388, 389, 390, 391,
+	392, 393, 394, 395, 396, 397, 398, 399, 400, 401, 402,
+	403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413,
+	414, 415, 416, 417, 418, 419, 420, 421, 422, 423, 424,
+	425, 426, 427, 428, 429, 430, 431, 432, 433, 434, 435,
+	436, 437, 438, 439, 440, 441, 442, 443, 444, 445, 446,
+	447, 448, 449, 450, 451, 451, 452, 453, 454, 455, 456,
+	457, 458, 459, 460, 461, 462, 463, 464, 465, 466, 467,
+	468, 469, 470, 471, 472, 473, 474, 475, 476, 477, 478,
+	479, 480, 481, 482, 483, 484, 485, 486, 486, 487, 488,
+	489, 490, 491, 492, 493, 494, 495, 496, 497, 498, 499,
+	500, 501, 502, 503, 504, 505, 506, 507, 508, 509, 509,
+	510, 511, 512, 513, 514, 515, 516, 517, 518, 519, 520,
+	521, 522, 523, 524, 525, 526, 527, 527, 528, 529, 530,
+	531, 532, 533, 534, 535, 536, 537, 538, 539, 540, 541,
+	542, 543, 543, 544, 545, 546, 547, 548, 549, 550, 551,
+	552, 553, 554, 555, 556, 557, 557, 558, 559, 560, 561,
+	562, 563, 564, 565, 566, 567, 568, 569, 570, 570, 571,
+	572, 573, 574, 575, 576, 577, 578, 579, 580, 581, 582,
+	582, 583, 584, 585, 586, 587, 588, 589, 590, 591, 592,
+	593, 594, 594, 595, 596, 597, 598, 599, 600, 601, 602,
+	603, 604, 604, 605, 606, 607, 608, 609, 610, 611, 612,
+	613, 614, 615, 615, 616, 617, 618, 619, 620, 621, 622,
+	623, 624, 624, 625, 626, 627, 628, 629, 630, 631, 632,
+	633, 634, 634, 635, 636, 637, 638, 639, 640, 641, 642,
+	643, 643, 644, 645, 646, 647, 648, 649, 650, 651, 651,
+	652, 653, 654, 655, 656, 657, 658, 659, 660, 660, 661,
+	662, 663, 664, 665, 666, 667, 668, 668, 669, 670, 671,
+	672, 673, 674, 675, 676, 676, 677, 678, 679, 680, 681,
+	682, 683, 684, 684, 685, 686, 687, 688, 689, 690, 691,
+	691, 692, 693, 694, 695, 696, 697, 698, 699, 699, 700,
+	701, 702, 703, 704, 705, 706, 706, 707, 708, 709, 710,
+	711, 712, 713, 713, 714, 715, 716, 717, 718, 719, 720,
+	720, 721, 722, 723, 724, 725, 726, 727, 727, 728, 729,
+	730, 731, 732, 733, 734, 734, 735, 736, 737, 738, 739,
+	740, 740, 741, 742, 743, 744, 745, 746, 747, 747, 748,
+	749, 750, 751, 752, 753, 753, 754, 755, 756, 757, 758,
+	759, 759, 760, 761, 762, 763, 764, 765, 766, 766, 767,
+	768, 769, 770, 771, 772, 772, 773, 774, 775, 776, 777,
+	778, 778, 779, 780, 781, 782, 783, 784, 784, 785, 786,
+	787, 788, 789, 790, 790, 791, 792, 793, 794, 795, 795,
+	796, 797, 798, 799, 800, 801, 801, 802, 803, 804, 805,
+	806, 807, 807, 808, 809, 810, 811, 812, 812, 813, 814,
+	815, 816, 817, 818, 818, 819, 820, 821, 822, 823, 823,
+	824, 825, 826, 827, 828, 829, 829, 830, 831, 832, 833,
+	834, 834, 835, 836, 837, 838, 839, 839, 840, 841, 842,
+	843, 844, 845, 845, 846, 847, 848, 849, 850, 850, 851,
+	852, 853, 854, 855, 855, 856, 857, 858, 859, 860, 860,
+	861, 862, 863, 864, 865, 865, 866, 867, 868, 869, 870,
+	870, 871, 872, 873, 874, 875, 875, 876, 877, 878, 879,
+	880, 880, 881, 882, 883, 884, 885, 885, 886, 887, 888,
+	889, 890, 890, 891, 892, 893, 894, 895, 895, 896, 897,
+	898, 899, 899, 900, 901, 902, 903, 904, 904, 905, 906,
+	907, 908, 909, 909, 910, 911, 912, 913, 913, 914, 915,
+	916, 917, 918, 918, 919, 920, 921, 922, 923, 923, 924,
+	925, 926, 927, 927, 928, 929, 930, 931, 932, 932, 933,
+	934, 935, 936, 936, 937, 938, 939, 940, 941, 941, 942,
+	943, 944, 945, 945, 946, 947, 948, 949, 950, 950, 951,
+	952, 953, 954, 954, 955, 956, 957, 958, 958, 959, 960,
+	961, 962, 963, 963, 964, 965, 966, 967, 967, 968, 969,
+	970, 971, 971, 972, 973, 974, 975, 976, 976, 977, 978,
+	979, 980, 980, 981, 982, 983, 984, 984, 985, 986, 987,
+	988, 988, 989, 990, 991, 992, 992, 993, 994, 995, 996,
+	997, 997, 998, 999, 1000, 1001, 1001, 1002, 1003, 1004, 1005,
+	1005, 1006, 1007, 1008, 1009, 1009, 1010, 1011, 1012, 1013, 1013,
+	1014, 1015, 1016, 1017, 1017, 1018, 1019, 1020, 1021, 1021, 1022,
+	1023,
+};
+
+static const u16 xgamma10_09[GAMMA10_TABLE_LENGTH] = {
+	0, 2, 4, 5, 7, 9, 10, 12, 13, 14, 16,
+	17, 19, 20, 22, 23, 24, 26, 27, 28, 30, 31,
+	32, 34, 35, 36, 38, 39, 40, 41, 43, 44, 45,
+	47, 48, 49, 50, 52, 53, 54, 55, 57, 58, 59,
+	60, 62, 63, 64, 65, 66, 68, 69, 70, 71, 72,
+	74, 75, 76, 77, 78, 80, 81, 82, 83, 84, 86,
+	87, 88, 89, 90, 92, 93, 94, 95, 96, 97, 99,
+	100, 101, 102, 103, 104, 106, 107, 108, 109, 110, 111,
+	112, 114, 115, 116, 117, 118, 119, 120, 122, 123, 124,
+	125, 126, 127, 128, 130, 131, 132, 133, 134, 135, 136,
+	137, 139, 140, 141, 142, 143, 144, 145, 146, 148, 149,
+	150, 151, 152, 153, 154, 155, 156, 158, 159, 160, 161,
+	162, 163, 164, 165, 166, 168, 169, 170, 171, 172, 173,
+	174, 175, 176, 177, 178, 180, 181, 182, 183, 184, 185,
+	186, 187, 188, 189, 190, 192, 193, 194, 195, 196, 197,
+	198, 199, 200, 201, 202, 203, 204, 206, 207, 208, 209,
+	210, 211, 212, 213, 214, 215, 216, 217, 218, 220, 221,
+	222, 223, 224, 225, 226, 227, 228, 229, 230, 231, 232,
+	233, 234, 235, 237, 238, 239, 240, 241, 242, 243, 244,
+	245, 246, 247, 248, 249, 250, 251, 252, 253, 254, 255,
+	257, 258, 259, 260, 261, 262, 263, 264, 265, 266, 267,
+	268, 269, 270, 271, 272, 273, 274, 275, 276, 277, 278,
+	280, 281, 282, 283, 284, 285, 286, 287, 288, 289, 290,
+	291, 292, 293, 294, 295, 296, 297, 298, 299, 300, 301,
+	302, 303, 304, 305, 306, 307, 308, 309, 311, 312, 313,
+	314, 315, 316, 317, 318, 319, 320, 321, 322, 323, 324,
+	325, 326, 327, 328, 329, 330, 331, 332, 333, 334, 335,
+	336, 337, 338, 339, 340, 341, 342, 343, 344, 345, 346,
+	347, 348, 349, 350, 351, 352, 353, 354, 355, 356, 357,
+	358, 359, 360, 361, 362, 363, 364, 365, 367, 368, 369,
+	370, 371, 372, 373, 374, 375, 376, 377, 378, 379, 380,
+	381, 382, 383, 384, 385, 386, 387, 388, 389, 390, 391,
+	392, 393, 394, 395, 396, 397, 398, 399, 400, 401, 402,
+	403, 404, 405, 406, 407, 408, 409, 410, 411, 412, 413,
+	414, 415, 416, 417, 418, 419, 420, 421, 422, 423, 424,
+	425, 426, 427, 427, 428, 429, 430, 431, 432, 433, 434,
+	435, 436, 437, 438, 439, 440, 441, 442, 443, 444, 445,
+	446, 447, 448, 449, 450, 451, 452, 453, 454, 455, 456,
+	457, 458, 459, 460, 461, 462, 463, 464, 465, 466, 467,
+	468, 469, 470, 471, 472, 473, 474, 475, 476, 477, 478,
+	479, 480, 481, 482, 483, 484, 485, 486, 487, 488, 489,
+	489, 490, 491, 492, 493, 494, 495, 496, 497, 498, 499,
+	500, 501, 502, 503, 504, 505, 506, 507, 508, 509, 510,
+	511, 512, 513, 514, 515, 516, 517, 518, 519, 520, 521,
+	522, 523, 524, 525, 525, 526, 527, 528, 529, 530, 531,
+	532, 533, 534, 535, 536, 537, 538, 539, 540, 541, 542,
+	543, 544, 545, 546, 547, 548, 549, 550, 551, 552, 553,
+	554, 554, 555, 556, 557, 558, 559, 560, 561, 562, 563,
+	564, 565, 566, 567, 568, 569, 570, 571, 572, 573, 574,
+	575, 576, 577, 578, 579, 579, 580, 581, 582, 583, 584,
+	585, 586, 587, 588, 589, 590, 591, 592, 593, 594, 595,
+	596, 597, 598, 599, 600, 601, 601, 602, 603, 604, 605,
+	606, 607, 608, 609, 610, 611, 612, 613, 614, 615, 616,
+	617, 618, 619, 620, 621, 621, 622, 623, 624, 625, 626,
+	627, 628, 629, 630, 631, 632, 633, 634, 635, 636, 637,
+	638, 639, 640, 640, 641, 642, 643, 644, 645, 646, 647,
+	648, 649, 650, 651, 652, 653, 654, 655, 656, 657, 658,
+	658, 659, 660, 661, 662, 663, 664, 665, 666, 667, 668,
+	669, 670, 671, 672, 673, 674, 675, 675, 676, 677, 678,
+	679, 680, 681, 682, 683, 684, 685, 686, 687, 688, 689,
+	690, 691, 691, 692, 693, 694, 695, 696, 697, 698, 699,
+	700, 701, 702, 703, 704, 705, 706, 706, 707, 708, 709,
+	710, 711, 712, 713, 714, 715, 716, 717, 718, 719, 720,
+	721, 721, 722, 723, 724, 725, 726, 727, 728, 729, 730,
+	731, 732, 733, 734, 735, 735, 736, 737, 738, 739, 740,
+	741, 742, 743, 744, 745, 746, 747, 748, 749, 749, 750,
+	751, 752, 753, 754, 755, 756, 757, 758, 759, 760, 761,
+	762, 762, 763, 764, 765, 766, 767, 768, 769, 770, 771,
+	772, 773, 774, 775, 776, 776, 777, 778, 779, 780, 781,
+	782, 783, 784, 785, 786, 787, 788, 788, 789, 790, 791,
+	792, 793, 794, 795, 796, 797, 798, 799, 800, 801, 801,
+	802, 803, 804, 805, 806, 807, 808, 809, 810, 811, 812,
+	813, 813, 814, 815, 816, 817, 818, 819, 820, 821, 822,
+	823, 824, 825, 825, 826, 827, 828, 829, 830, 831, 832,
+	833, 834, 835, 836, 836, 837, 838, 839, 840, 841, 842,
+	843, 844, 845, 846, 847, 848, 848, 849, 850, 851, 852,
+	853, 854, 855, 856, 857, 858, 859, 859, 860, 861, 862,
+	863, 864, 865, 866, 867, 868, 869, 870, 870, 871, 872,
+	873, 874, 875, 876, 877, 878, 879, 880, 881, 881, 882,
+	883, 884, 885, 886, 887, 888, 889, 890, 891, 892, 892,
+	893, 894, 895, 896, 897, 898, 899, 900, 901, 902, 902,
+	903, 904, 905, 906, 907, 908, 909, 910, 911, 912, 913,
+	913, 914, 915, 916, 917, 918, 919, 920, 921, 922, 923,
+	923, 924, 925, 926, 927, 928, 929, 930, 931, 932, 933,
+	933, 934, 935, 936, 937, 938, 939, 940, 941, 942, 943,
+	943, 944, 945, 946, 947, 948, 949, 950, 951, 952, 953,
+	953, 954, 955, 956, 957, 958, 959, 960, 961, 962, 962,
+	963, 964, 965, 966, 967, 968, 969, 970, 971, 972, 972,
+	973, 974, 975, 976, 977, 978, 979, 980, 981, 982, 982,
+	983, 984, 985, 986, 987, 988, 989, 990, 991, 991, 992,
+	993, 994, 995, 996, 997, 998, 999, 1000, 1000, 1001, 1002,
+	1003, 1004, 1005, 1006, 1007, 1008, 1009, 1009, 1010, 1011, 1012,
+	1013, 1014, 1015, 1016, 1017, 1018, 1018, 1019, 1020, 1021, 1022,
+	1023,
+};
+
+static const u16 xgamma10_10[GAMMA10_TABLE_LENGTH] = {
+	0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
+	11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21,
+	22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32,
+	33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43,
+	44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54,
+	55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65,
+	66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76,
+	77, 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
+	88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98,
+	99, 100, 101, 102, 103, 104, 105, 106, 107, 108, 109,
+	110, 111, 112, 113, 114, 115, 116, 117, 118, 119, 120,
+	121, 122, 123, 124, 125, 126, 127, 128, 129, 130, 131,
+	132, 133, 134, 135, 136, 137, 138, 139, 140, 141, 142,
+	143, 144, 145, 146, 147, 148, 149, 150, 151, 152, 153,
+	154, 155, 156, 157, 158, 159, 160, 161, 162, 163, 164,
+	165, 166, 167, 168, 169, 170, 171, 172, 173, 174, 175,
+	176, 177, 178, 179, 180, 181, 182, 183, 184, 185, 186,
+	187, 188, 189, 190, 191, 192, 193, 194, 195, 196, 197,
+	198, 199, 200, 201, 202, 203, 204, 205, 206, 207, 208,
+	209, 210, 211, 212, 213, 214, 215, 216, 217, 218, 219,
+	220, 221, 222, 223, 224, 225, 226, 227, 228, 229, 230,
+	231, 232, 233, 234, 235, 236, 237, 238, 239, 240, 241,
+	242, 243, 244, 245, 246, 247, 248, 249, 250, 251, 252,
+	253, 254, 255, 256, 257, 258, 259, 260, 261, 262, 263,
+	264, 265, 266, 267, 268, 269, 270, 271, 272, 273, 274,
+	275, 276, 277, 278, 279, 280, 281, 282, 283, 284, 285,
+	286, 287, 288, 289, 290, 291, 292, 293, 294, 295, 296,
+	297, 298, 299, 300, 301, 302, 303, 304, 305, 306, 307,
+	308, 309, 310, 311, 312, 313, 314, 315, 316, 317, 318,
+	319, 320, 321, 322, 323, 324, 325, 326, 327, 328, 329,
+	330, 331, 332, 333, 334, 335, 336, 337, 338, 339, 340,
+	341, 342, 343, 344, 345, 346, 347, 348, 349, 350, 351,
+	352, 353, 354, 355, 356, 357, 358, 359, 360, 361, 362,
+	363, 364, 365, 366, 367, 368, 369, 370, 371, 372, 373,
+	374, 375, 376, 377, 378, 379, 380, 381, 382, 383, 384,
+	385, 386, 387, 388, 389, 390, 391, 392, 393, 394, 395,
+	396, 397, 398, 399, 400, 401, 402, 403, 404, 405, 406,
+	407, 408, 409, 410, 411, 412, 413, 414, 415, 416, 417,
+	418, 419, 420, 421, 422, 423, 424, 425, 426, 427, 428,
+	429, 430, 431, 432, 433, 434, 435, 436, 437, 438, 439,
+	440, 441, 442, 443, 444, 445, 446, 447, 448, 449, 450,
+	451, 452, 453, 454, 455, 456, 457, 458, 459, 460, 461,
+	462, 463, 464, 465, 466, 467, 468, 469, 470, 471, 472,
+	473, 474, 475, 476, 477, 478, 479, 480, 481, 482, 483,
+	484, 485, 486, 487, 488, 489, 490, 491, 492, 493, 494,
+	495, 496, 497, 498, 499, 500, 501, 502, 503, 504, 505,
+	506, 507, 508, 509, 510, 511, 512, 513, 514, 515, 516,
+	517, 518, 519, 520, 521, 522, 523, 524, 525, 526, 527,
+	528, 529, 530, 531, 532, 533, 534, 535, 536, 537, 538,
+	539, 540, 541, 542, 543, 544, 545, 546, 547, 548, 549,
+	550, 551, 552, 553, 554, 555, 556, 557, 558, 559, 560,
+	561, 562, 563, 564, 565, 566, 567, 568, 569, 570, 571,
+	572, 573, 574, 575, 576, 577, 578, 579, 580, 581, 582,
+	583, 584, 585, 586, 587, 588, 589, 590, 591, 592, 593,
+	594, 595, 596, 597, 598, 599, 600, 601, 602, 603, 604,
+	605, 606, 607, 608, 609, 610, 611, 612, 613, 614, 615,
+	616, 617, 618, 619, 620, 621, 622, 623, 624, 625, 626,
+	627, 628, 629, 630, 631, 632, 633, 634, 635, 636, 637,
+	638, 639, 640, 641, 642, 643, 644, 645, 646, 647, 648,
+	649, 650, 651, 652, 653, 654, 655, 656, 657, 658, 659,
+	660, 661, 662, 663, 664, 665, 666, 667, 668, 669, 670,
+	671, 672, 673, 674, 675, 676, 677, 678, 679, 680, 681,
+	682, 683, 684, 685, 686, 687, 688, 689, 690, 691, 692,
+	693, 694, 695, 696, 697, 698, 699, 700, 701, 702, 703,
+	704, 705, 706, 707, 708, 709, 710, 711, 712, 713, 714,
+	715, 716, 717, 718, 719, 720, 721, 722, 723, 724, 725,
+	726, 727, 728, 729, 730, 731, 732, 733, 734, 735, 736,
+	737, 738, 739, 740, 741, 742, 743, 744, 745, 746, 747,
+	748, 749, 750, 751, 752, 753, 754, 755, 756, 757, 758,
+	759, 760, 761, 762, 763, 764, 765, 766, 767, 768, 769,
+	770, 771, 772, 773, 774, 775, 776, 777, 778, 779, 780,
+	781, 782, 783, 784, 785, 786, 787, 788, 789, 790, 791,
+	792, 793, 794, 795, 796, 797, 798, 799, 800, 801, 802,
+	803, 804, 805, 806, 807, 808, 809, 810, 811, 812, 813,
+	814, 815, 816, 817, 818, 819, 820, 821, 822, 823, 824,
+	825, 826, 827, 828, 829, 830, 831, 832, 833, 834, 835,
+	836, 837, 838, 839, 840, 841, 842, 843, 844, 845, 846,
+	847, 848, 849, 850, 851, 852, 853, 854, 855, 856, 857,
+	858, 859, 860, 861, 862, 863, 864, 865, 866, 867, 868,
+	869, 870, 871, 872, 873, 874, 875, 876, 877, 878, 879,
+	880, 881, 882, 883, 884, 885, 886, 887, 888, 889, 890,
+	891, 892, 893, 894, 895, 896, 897, 898, 899, 900, 901,
+	902, 903, 904, 905, 906, 907, 908, 909, 910, 911, 912,
+	913, 914, 915, 916, 917, 918, 919, 920, 921, 922, 923,
+	924, 925, 926, 927, 928, 929, 930, 931, 932, 933, 934,
+	935, 936, 937, 938, 939, 940, 941, 942, 943, 944, 945,
+	946, 947, 948, 949, 950, 951, 952, 953, 954, 955, 956,
+	957, 958, 959, 960, 961, 962, 963, 964, 965, 966, 967,
+	968, 969, 970, 971, 972, 973, 974, 975, 976, 977, 978,
+	979, 980, 981, 982, 983, 984, 985, 986, 987, 988, 989,
+	990, 991, 992, 993, 994, 995, 996, 997, 998, 999, 1000,
+	1001, 1002, 1003, 1004, 1005, 1006, 1007, 1008, 1009, 1010, 1011,
+	1012, 1013, 1014, 1015, 1016, 1017, 1018, 1019, 1020, 1021, 1022,
+	1023,
+};
+
+static const u16 xgamma10_11[GAMMA10_TABLE_LENGTH] = {
+	0, 1, 1, 2, 2, 3, 4, 4, 5, 6, 6,
+	7, 8, 8, 9, 10, 11, 11, 12, 13, 13, 14,
+	15, 16, 16, 17, 18, 19, 20, 20, 21, 22, 23,
+	23, 24, 25, 26, 27, 27, 28, 29, 30, 31, 31,
+	32, 33, 34, 35, 35, 36, 37, 38, 39, 39, 40,
+	41, 42, 43, 44, 44, 45, 46, 47, 48, 49, 49,
+	50, 51, 52, 53, 54, 54, 55, 56, 57, 58, 59,
+	59, 60, 61, 62, 63, 64, 65, 65, 66, 67, 68,
+	69, 70, 71, 71, 72, 73, 74, 75, 76, 77, 78,
+	78, 79, 80, 81, 82, 83, 84, 84, 85, 86, 87,
+	88, 89, 90, 91, 92, 92, 93, 94, 95, 96, 97,
+	98, 99, 100, 100, 101, 102, 103, 104, 105, 106, 107,
+	108, 108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
+	117, 118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
+	127, 128, 129, 130, 131, 132, 133, 134, 135, 136, 137,
+	137, 138, 139, 140, 141, 142, 143, 144, 145, 146, 147,
+	148, 149, 149, 150, 151, 152, 153, 154, 155, 156, 157,
+	158, 159, 160, 161, 161, 162, 163, 164, 165, 166, 167,
+	168, 169, 170, 171, 172, 173, 174, 175, 175, 176, 177,
+	178, 179, 180, 181, 182, 183, 184, 185, 186, 187, 188,
+	189, 190, 191, 191, 192, 193, 194, 195, 196, 197, 198,
+	199, 200, 201, 202, 203, 204, 205, 206, 207, 208, 209,
+	210, 210, 211, 212, 213, 214, 215, 216, 217, 218, 219,
+	220, 221, 222, 223, 224, 225, 226, 227, 228, 229, 230,
+	231, 232, 232, 233, 234, 235, 236, 237, 238, 239, 240,
+	241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 251,
+	252, 253, 254, 255, 256, 257, 258, 259, 260, 261, 261,
+	262, 263, 264, 265, 266, 267, 268, 269, 270, 271, 272,
+	273, 274, 275, 276, 277, 278, 279, 280, 281, 282, 283,
+	284, 285, 286, 287, 288, 289, 290, 291, 292, 293, 294,
+	295, 296, 297, 298, 299, 300, 301, 302, 303, 304, 305,
+	306, 307, 307, 308, 309, 310, 311, 312, 313, 314, 315,
+	316, 317, 318, 319, 320, 321, 322, 323, 324, 325, 326,
+	327, 328, 329, 330, 331, 332, 333, 334, 335, 336, 337,
+	338, 339, 340, 341, 342, 343, 344, 345, 346, 347, 348,
+	349, 350, 351, 352, 353, 354, 355, 356, 357, 358, 359,
+	360, 361, 362, 363, 364, 365, 366, 367, 368, 369, 370,
+	371, 372, 373, 374, 375, 376, 377, 378, 379, 380, 381,
+	382, 383, 384, 385, 386, 387, 388, 389, 390, 391, 392,
+	393, 394, 395, 396, 397, 398, 399, 400, 401, 402, 403,
+	404, 405, 406, 407, 408, 409, 410, 411, 412, 414, 415,
+	416, 417, 418, 419, 420, 421, 422, 423, 424, 425, 426,
+	427, 428, 429, 430, 431, 432, 433, 434, 435, 436, 437,
+	438, 439, 440, 441, 442, 443, 444, 445, 446, 447, 448,
+	449, 450, 451, 452, 453, 454, 455, 456, 457, 458, 459,
+	460, 461, 462, 463, 464, 465, 466, 468, 469, 470, 471,
+	472, 473, 474, 475, 476, 477, 478, 479, 480, 481, 482,
+	483, 484, 485, 486, 487, 488, 489, 490, 491, 492, 493,
+	494, 495, 496, 497, 498, 499, 500, 501, 502, 503, 505,
+	506, 507, 508, 509, 510, 511, 512, 513, 514, 515, 516,
+	517, 518, 519, 520, 521, 522, 523, 524, 525, 526, 527,
+	528, 529, 530, 531, 532, 533, 535, 536, 537, 538, 539,
+	540, 541, 542, 543, 544, 545, 546, 547, 548, 549, 550,
+	551, 552, 553, 554, 555, 556, 557, 558, 559, 560, 562,
+	563, 564, 565, 566, 567, 568, 569, 570, 571, 572, 573,
+	574, 575, 576, 577, 578, 579, 580, 581, 582, 583, 584,
+	586, 587, 588, 589, 590, 591, 592, 593, 594, 595, 596,
+	597, 598, 599, 600, 601, 602, 603, 604, 605, 606, 608,
+	609, 610, 611, 612, 613, 614, 615, 616, 617, 618, 619,
+	620, 621, 622, 623, 624, 625, 626, 627, 629, 630, 631,
+	632, 633, 634, 635, 636, 637, 638, 639, 640, 641, 642,
+	643, 644, 645, 646, 648, 649, 650, 651, 652, 653, 654,
+	655, 656, 657, 658, 659, 660, 661, 662, 663, 664, 665,
+	667, 668, 669, 670, 671, 672, 673, 674, 675, 676, 677,
+	678, 679, 680, 681, 682, 683, 685, 686, 687, 688, 689,
+	690, 691, 692, 693, 694, 695, 696, 697, 698, 699, 700,
+	702, 703, 704, 705, 706, 707, 708, 709, 710, 711, 712,
+	713, 714, 715, 716, 717, 719, 720, 721, 722, 723, 724,
+	725, 726, 727, 728, 729, 730, 731, 732, 733, 735, 736,
+	737, 738, 739, 740, 741, 742, 743, 744, 745, 746, 747,
+	748, 750, 751, 752, 753, 754, 755, 756, 757, 758, 759,
+	760, 761, 762, 763, 764, 766, 767, 768, 769, 770, 771,
+	772, 773, 774, 775, 776, 777, 778, 779, 781, 782, 783,
+	784, 785, 786, 787, 788, 789, 790, 791, 792, 793, 795,
+	796, 797, 798, 799, 800, 801, 802, 803, 804, 805, 806,
+	807, 809, 810, 811, 812, 813, 814, 815, 816, 817, 818,
+	819, 820, 821, 823, 824, 825, 826, 827, 828, 829, 830,
+	831, 832, 833, 834, 835, 837, 838, 839, 840, 841, 842,
+	843, 844, 845, 846, 847, 848, 850, 851, 852, 853, 854,
+	855, 856, 857, 858, 859, 860, 861, 863, 864, 865, 866,
+	867, 868, 869, 870, 871, 872, 873, 874, 876, 877, 878,
+	879, 880, 881, 882, 883, 884, 885, 886, 887, 889, 890,
+	891, 892, 893, 894, 895, 896, 897, 898, 899, 900, 902,
+	903, 904, 905, 906, 907, 908, 909, 910, 911, 912, 914,
+	915, 916, 917, 918, 919, 920, 921, 922, 923, 924, 926,
+	927, 928, 929, 930, 931, 932, 933, 934, 935, 936, 938,
+	939, 940, 941, 942, 943, 944, 945, 946, 947, 948, 950,
+	951, 952, 953, 954, 955, 956, 957, 958, 959, 960, 962,
+	963, 964, 965, 966, 967, 968, 969, 970, 971, 973, 974,
+	975, 976, 977, 978, 979, 980, 981, 982, 983, 985, 986,
+	987, 988, 989, 990, 991, 992, 993, 994, 996, 997, 998,
+	999, 1000, 1001, 1002, 1003, 1004, 1005, 1007, 1008, 1009, 1010,
+	1011, 1012, 1013, 1014, 1015, 1016, 1018, 1019, 1020, 1021, 1022,
+	1023,
+};
+
+static const u16 xgamma10_12[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 1, 1, 1, 2, 2, 3, 3, 3, 4,
+	4, 5, 5, 6, 6, 7, 7, 8, 9, 9, 10,
+	10, 11, 11, 12, 12, 13, 14, 14, 15, 15, 16,
+	17, 17, 18, 18, 19, 20, 20, 21, 22, 22, 23,
+	23, 24, 25, 25, 26, 27, 27, 28, 29, 29, 30,
+	31, 31, 32, 33, 33, 34, 35, 35, 36, 37, 37,
+	38, 39, 40, 40, 41, 42, 42, 43, 44, 44, 45,
+	46, 47, 47, 48, 49, 49, 50, 51, 52, 52, 53,
+	54, 55, 55, 56, 57, 58, 58, 59, 60, 61, 61,
+	62, 63, 64, 64, 65, 66, 67, 67, 68, 69, 70,
+	70, 71, 72, 73, 74, 74, 75, 76, 77, 77, 78,
+	79, 80, 81, 81, 82, 83, 84, 84, 85, 86, 87,
+	88, 88, 89, 90, 91, 92, 92, 93, 94, 95, 96,
+	96, 97, 98, 99, 100, 101, 101, 102, 103, 104, 105,
+	105, 106, 107, 108, 109, 110, 110, 111, 112, 113, 114,
+	115, 115, 116, 117, 118, 119, 120, 120, 121, 122, 123,
+	124, 125, 125, 126, 127, 128, 129, 130, 131, 131, 132,
+	133, 134, 135, 136, 137, 137, 138, 139, 140, 141, 142,
+	143, 143, 144, 145, 146, 147, 148, 149, 150, 150, 151,
+	152, 153, 154, 155, 156, 157, 157, 158, 159, 160, 161,
+	162, 163, 164, 164, 165, 166, 167, 168, 169, 170, 171,
+	172, 172, 173, 174, 175, 176, 177, 178, 179, 180, 180,
+	181, 182, 183, 184, 185, 186, 187, 188, 189, 190, 190,
+	191, 192, 193, 194, 195, 196, 197, 198, 199, 200, 200,
+	201, 202, 203, 204, 205, 206, 207, 208, 209, 210, 211,
+	211, 212, 213, 214, 215, 216, 217, 218, 219, 220, 221,
+	222, 223, 224, 224, 225, 226, 227, 228, 229, 230, 231,
+	232, 233, 234, 235, 236, 237, 238, 238, 239, 240, 241,
+	242, 243, 244, 245, 246, 247, 248, 249, 250, 251, 252,
+	253, 254, 255, 256, 256, 257, 258, 259, 260, 261, 262,
+	263, 264, 265, 266, 267, 268, 269, 270, 271, 272, 273,
+	274, 275, 276, 277, 278, 279, 280, 280, 281, 282, 283,
+	284, 285, 286, 287, 288, 289, 290, 291, 292, 293, 294,
+	295, 296, 297, 298, 299, 300, 301, 302, 303, 304, 305,
+	306, 307, 308, 309, 310, 311, 312, 313, 314, 315, 316,
+	317, 318, 319, 320, 321, 322, 323, 324, 325, 326, 327,
+	328, 329, 330, 331, 332, 333, 334, 334, 335, 336, 337,
+	338, 339, 340, 341, 342, 343, 344, 345, 346, 347, 348,
+	349, 350, 351, 353, 354, 355, 356, 357, 358, 359, 360,
+	361, 362, 363, 364, 365, 366, 367, 368, 369, 370, 371,
+	372, 373, 374, 375, 376, 377, 378, 379, 380, 381, 382,
+	383, 384, 385, 386, 387, 388, 389, 390, 391, 392, 393,
+	394, 395, 396, 397, 398, 399, 400, 401, 402, 403, 404,
+	405, 406, 407, 408, 409, 411, 412, 413, 414, 415, 416,
+	417, 418, 419, 420, 421, 422, 423, 424, 425, 426, 427,
+	428, 429, 430, 431, 432, 433, 434, 435, 436, 437, 439,
+	440, 441, 442, 443, 444, 445, 446, 447, 448, 449, 450,
+	451, 452, 453, 454, 455, 456, 457, 458, 459, 460, 462,
+	463, 464, 465, 466, 467, 468, 469, 470, 471, 472, 473,
+	474, 475, 476, 477, 478, 479, 481, 482, 483, 484, 485,
+	486, 487, 488, 489, 490, 491, 492, 493, 494, 495, 496,
+	497, 499, 500, 501, 502, 503, 504, 505, 506, 507, 508,
+	509, 510, 511, 512, 513, 515, 516, 517, 518, 519, 520,
+	521, 522, 523, 524, 525, 526, 527, 529, 530, 531, 532,
+	533, 534, 535, 536, 537, 538, 539, 540, 541, 543, 544,
+	545, 546, 547, 548, 549, 550, 551, 552, 553, 554, 555,
+	557, 558, 559, 560, 561, 562, 563, 564, 565, 566, 567,
+	569, 570, 571, 572, 573, 574, 575, 576, 577, 578, 579,
+	581, 582, 583, 584, 585, 586, 587, 588, 589, 590, 591,
+	593, 594, 595, 596, 597, 598, 599, 600, 601, 602, 604,
+	605, 606, 607, 608, 609, 610, 611, 612, 613, 615, 616,
+	617, 618, 619, 620, 621, 622, 623, 624, 626, 627, 628,
+	629, 630, 631, 632, 633, 634, 636, 637, 638, 639, 640,
+	641, 642, 643, 644, 646, 647, 648, 649, 650, 651, 652,
+	653, 654, 656, 657, 658, 659, 660, 661, 662, 663, 664,
+	666, 667, 668, 669, 670, 671, 672, 673, 675, 676, 677,
+	678, 679, 680, 681, 682, 683, 685, 686, 687, 688, 689,
+	690, 691, 692, 694, 695, 696, 697, 698, 699, 700, 701,
+	703, 704, 705, 706, 707, 708, 709, 710, 712, 713, 714,
+	715, 716, 717, 718, 720, 721, 722, 723, 724, 725, 726,
+	727, 729, 730, 731, 732, 733, 734, 735, 737, 738, 739,
+	740, 741, 742, 743, 745, 746, 747, 748, 749, 750, 751,
+	752, 754, 755, 756, 757, 758, 759, 760, 762, 763, 764,
+	765, 766, 767, 768, 770, 771, 772, 773, 774, 775, 776,
+	778, 779, 780, 781, 782, 783, 785, 786, 787, 788, 789,
+	790, 791, 793, 794, 795, 796, 797, 798, 799, 801, 802,
+	803, 804, 805, 806, 808, 809, 810, 811, 812, 813, 814,
+	816, 817, 818, 819, 820, 821, 823, 824, 825, 826, 827,
+	828, 830, 831, 832, 833, 834, 835, 836, 838, 839, 840,
+	841, 842, 843, 845, 846, 847, 848, 849, 850, 852, 853,
+	854, 855, 856, 857, 859, 860, 861, 862, 863, 864, 866,
+	867, 868, 869, 870, 871, 873, 874, 875, 876, 877, 878,
+	880, 881, 882, 883, 884, 885, 887, 888, 889, 890, 891,
+	892, 894, 895, 896, 897, 898, 900, 901, 902, 903, 904,
+	905, 907, 908, 909, 910, 911, 912, 914, 915, 916, 917,
+	918, 920, 921, 922, 923, 924, 925, 927, 928, 929, 930,
+	931, 932, 934, 935, 936, 937, 938, 940, 941, 942, 943,
+	944, 946, 947, 948, 949, 950, 951, 953, 954, 955, 956,
+	957, 959, 960, 961, 962, 963, 964, 966, 967, 968, 969,
+	970, 972, 973, 974, 975, 976, 978, 979, 980, 981, 982,
+	984, 985, 986, 987, 988, 989, 991, 992, 993, 994, 995,
+	997, 998, 999, 1000, 1001, 1003, 1004, 1005, 1006, 1007, 1009,
+	1010, 1011, 1012, 1013, 1015, 1016, 1017, 1018, 1019, 1021, 1022,
+	1023,
+};
+
+static const u16 xgamma10_13[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2,
+	3, 3, 4, 4, 4, 5, 5, 5, 6, 6, 7,
+	7, 7, 8, 8, 9, 9, 10, 10, 10, 11, 11,
+	12, 12, 13, 13, 14, 14, 15, 15, 16, 16, 17,
+	17, 18, 18, 19, 19, 20, 20, 21, 21, 22, 22,
+	23, 23, 24, 25, 25, 26, 26, 27, 27, 28, 28,
+	29, 30, 30, 31, 31, 32, 32, 33, 34, 34, 35,
+	35, 36, 37, 37, 38, 38, 39, 40, 40, 41, 42,
+	42, 43, 43, 44, 45, 45, 46, 47, 47, 48, 48,
+	49, 50, 50, 51, 52, 52, 53, 54, 54, 55, 56,
+	56, 57, 58, 58, 59, 60, 60, 61, 62, 62, 63,
+	64, 64, 65, 66, 67, 67, 68, 69, 69, 70, 71,
+	71, 72, 73, 74, 74, 75, 76, 76, 77, 78, 79,
+	79, 80, 81, 81, 82, 83, 84, 84, 85, 86, 87,
+	87, 88, 89, 89, 90, 91, 92, 92, 93, 94, 95,
+	95, 96, 97, 98, 98, 99, 100, 101, 102, 102, 103,
+	104, 105, 105, 106, 107, 108, 108, 109, 110, 111, 112,
+	112, 113, 114, 115, 115, 116, 117, 118, 119, 119, 120,
+	121, 122, 123, 123, 124, 125, 126, 127, 127, 128, 129,
+	130, 131, 131, 132, 133, 134, 135, 135, 136, 137, 138,
+	139, 140, 140, 141, 142, 143, 144, 145, 145, 146, 147,
+	148, 149, 149, 150, 151, 152, 153, 154, 155, 155, 156,
+	157, 158, 159, 160, 160, 161, 162, 163, 164, 165, 166,
+	166, 167, 168, 169, 170, 171, 172, 172, 173, 174, 175,
+	176, 177, 178, 178, 179, 180, 181, 182, 183, 184, 185,
+	185, 186, 187, 188, 189, 190, 191, 192, 192, 193, 194,
+	195, 196, 197, 198, 199, 200, 200, 201, 202, 203, 204,
+	205, 206, 207, 208, 209, 209, 210, 211, 212, 213, 214,
+	215, 216, 217, 218, 218, 219, 220, 221, 222, 223, 224,
+	225, 226, 227, 228, 229, 229, 230, 231, 232, 233, 234,
+	235, 236, 237, 238, 239, 240, 241, 242, 242, 243, 244,
+	245, 246, 247, 248, 249, 250, 251, 252, 253, 254, 255,
+	256, 257, 257, 258, 259, 260, 261, 262, 263, 264, 265,
+	266, 267, 268, 269, 270, 271, 272, 273, 274, 275, 276,
+	277, 278, 278, 279, 280, 281, 282, 283, 284, 285, 286,
+	287, 288, 289, 290, 291, 292, 293, 294, 295, 296, 297,
+	298, 299, 300, 301, 302, 303, 304, 305, 306, 307, 308,
+	309, 310, 311, 312, 313, 314, 315, 316, 317, 318, 319,
+	320, 321, 322, 323, 324, 325, 326, 327, 328, 329, 330,
+	331, 332, 333, 334, 335, 336, 337, 338, 339, 340, 341,
+	342, 343, 344, 345, 346, 347, 348, 349, 350, 351, 352,
+	353, 354, 355, 356, 357, 358, 359, 360, 361, 362, 363,
+	364, 365, 366, 367, 368, 369, 370, 371, 372, 373, 374,
+	375, 376, 377, 378, 379, 380, 381, 383, 384, 385, 386,
+	387, 388, 389, 390, 391, 392, 393, 394, 395, 396, 397,
+	398, 399, 400, 401, 402, 403, 404, 405, 407, 408, 409,
+	410, 411, 412, 413, 414, 415, 416, 417, 418, 419, 420,
+	421, 422, 423, 424, 426, 427, 428, 429, 430, 431, 432,
+	433, 434, 435, 436, 437, 438, 439, 440, 442, 443, 444,
+	445, 446, 447, 448, 449, 450, 451, 452, 453, 454, 455,
+	457, 458, 459, 460, 461, 462, 463, 464, 465, 466, 467,
+	468, 470, 471, 472, 473, 474, 475, 476, 477, 478, 479,
+	480, 482, 483, 484, 485, 486, 487, 488, 489, 490, 491,
+	493, 494, 495, 496, 497, 498, 499, 500, 501, 502, 504,
+	505, 506, 507, 508, 509, 510, 511, 512, 513, 515, 516,
+	517, 518, 519, 520, 521, 522, 523, 525, 526, 527, 528,
+	529, 530, 531, 532, 534, 535, 536, 537, 538, 539, 540,
+	541, 542, 544, 545, 546, 547, 548, 549, 550, 551, 553,
+	554, 555, 556, 557, 558, 559, 561, 562, 563, 564, 565,
+	566, 567, 568, 570, 571, 572, 573, 574, 575, 576, 578,
+	579, 580, 581, 582, 583, 584, 586, 587, 588, 589, 590,
+	591, 592, 594, 595, 596, 597, 598, 599, 600, 602, 603,
+	604, 605, 606, 607, 608, 610, 611, 612, 613, 614, 615,
+	617, 618, 619, 620, 621, 622, 624, 625, 626, 627, 628,
+	629, 630, 632, 633, 634, 635, 636, 637, 639, 640, 641,
+	642, 643, 644, 646, 647, 648, 649, 650, 652, 653, 654,
+	655, 656, 657, 659, 660, 661, 662, 663, 664, 666, 667,
+	668, 669, 670, 671, 673, 674, 675, 676, 677, 679, 680,
+	681, 682, 683, 684, 686, 687, 688, 689, 690, 692, 693,
+	694, 695, 696, 698, 699, 700, 701, 702, 704, 705, 706,
+	707, 708, 709, 711, 712, 713, 714, 715, 717, 718, 719,
+	720, 721, 723, 724, 725, 726, 727, 729, 730, 731, 732,
+	733, 735, 736, 737, 738, 739, 741, 742, 743, 744, 746,
+	747, 748, 749, 750, 752, 753, 754, 755, 756, 758, 759,
+	760, 761, 762, 764, 765, 766, 767, 769, 770, 771, 772,
+	773, 775, 776, 777, 778, 780, 781, 782, 783, 784, 786,
+	787, 788, 789, 791, 792, 793, 794, 795, 797, 798, 799,
+	800, 802, 803, 804, 805, 807, 808, 809, 810, 811, 813,
+	814, 815, 816, 818, 819, 820, 821, 823, 824, 825, 826,
+	827, 829, 830, 831, 832, 834, 835, 836, 837, 839, 840,
+	841, 842, 844, 845, 846, 847, 849, 850, 851, 852, 854,
+	855, 856, 857, 859, 860, 861, 862, 864, 865, 866, 867,
+	869, 870, 871, 872, 874, 875, 876, 877, 879, 880, 881,
+	882, 884, 885, 886, 887, 889, 890, 891, 892, 894, 895,
+	896, 897, 899, 900, 901, 903, 904, 905, 906, 908, 909,
+	910, 911, 913, 914, 915, 916, 918, 919, 920, 922, 923,
+	924, 925, 927, 928, 929, 930, 932, 933, 934, 935, 937,
+	938, 939, 941, 942, 943, 944, 946, 947, 948, 950, 951,
+	952, 953, 955, 956, 957, 958, 960, 961, 962, 964, 965,
+	966, 967, 969, 970, 971, 973, 974, 975, 976, 978, 979,
+	980, 982, 983, 984, 985, 987, 988, 989, 991, 992, 993,
+	994, 996, 997, 998, 1000, 1001, 1002, 1004, 1005, 1006, 1007,
+	1009, 1010, 1011, 1013, 1014, 1015, 1017, 1018, 1019, 1020, 1022,
+	1023,
+};
+
+static const u16 xgamma10_14[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 3, 3, 3, 3, 4, 4, 4, 4,
+	5, 5, 5, 6, 6, 6, 7, 7, 7, 8, 8,
+	8, 9, 9, 9, 10, 10, 11, 11, 11, 12, 12,
+	12, 13, 13, 14, 14, 15, 15, 15, 16, 16, 17,
+	17, 18, 18, 18, 19, 19, 20, 20, 21, 21, 22,
+	22, 23, 23, 23, 24, 24, 25, 25, 26, 26, 27,
+	27, 28, 28, 29, 29, 30, 30, 31, 31, 32, 32,
+	33, 34, 34, 35, 35, 36, 36, 37, 37, 38, 38,
+	39, 39, 40, 41, 41, 42, 42, 43, 43, 44, 45,
+	45, 46, 46, 47, 47, 48, 49, 49, 50, 50, 51,
+	52, 52, 53, 53, 54, 55, 55, 56, 56, 57, 58,
+	58, 59, 59, 60, 61, 61, 62, 63, 63, 64, 64,
+	65, 66, 66, 67, 68, 68, 69, 70, 70, 71, 72,
+	72, 73, 74, 74, 75, 76, 76, 77, 78, 78, 79,
+	80, 80, 81, 82, 82, 83, 84, 84, 85, 86, 86,
+	87, 88, 88, 89, 90, 91, 91, 92, 93, 93, 94,
+	95, 95, 96, 97, 98, 98, 99, 100, 100, 101, 102,
+	103, 103, 104, 105, 106, 106, 107, 108, 109, 109, 110,
+	111, 111, 112, 113, 114, 114, 115, 116, 117, 117, 118,
+	119, 120, 120, 121, 122, 123, 124, 124, 125, 126, 127,
+	127, 128, 129, 130, 130, 131, 132, 133, 134, 134, 135,
+	136, 137, 138, 138, 139, 140, 141, 141, 142, 143, 144,
+	145, 145, 146, 147, 148, 149, 150, 150, 151, 152, 153,
+	154, 154, 155, 156, 157, 158, 158, 159, 160, 161, 162,
+	163, 163, 164, 165, 166, 167, 168, 168, 169, 170, 171,
+	172, 173, 173, 174, 175, 176, 177, 178, 179, 179, 180,
+	181, 182, 183, 184, 185, 185, 186, 187, 188, 189, 190,
+	191, 191, 192, 193, 194, 195, 196, 197, 198, 198, 199,
+	200, 201, 202, 203, 204, 205, 205, 206, 207, 208, 209,
+	210, 211, 212, 213, 213, 214, 215, 216, 217, 218, 219,
+	220, 221, 222, 222, 223, 224, 225, 226, 227, 228, 229,
+	230, 231, 232, 232, 233, 234, 235, 236, 237, 238, 239,
+	240, 241, 242, 243, 244, 244, 245, 246, 247, 248, 249,
+	250, 251, 252, 253, 254, 255, 256, 257, 258, 259, 259,
+	260, 261, 262, 263, 264, 265, 266, 267, 268, 269, 270,
+	271, 272, 273, 274, 275, 276, 277, 278, 279, 280, 281,
+	282, 282, 283, 284, 285, 286, 287, 288, 289, 290, 291,
+	292, 293, 294, 295, 296, 297, 298, 299, 300, 301, 302,
+	303, 304, 305, 306, 307, 308, 309, 310, 311, 312, 313,
+	314, 315, 316, 317, 318, 319, 320, 321, 322, 323, 324,
+	325, 326, 327, 328, 329, 330, 331, 332, 333, 334, 335,
+	336, 337, 338, 339, 340, 341, 342, 343, 344, 345, 346,
+	347, 348, 349, 351, 352, 353, 354, 355, 356, 357, 358,
+	359, 360, 361, 362, 363, 364, 365, 366, 367, 368, 369,
+	370, 371, 372, 373, 374, 375, 377, 378, 379, 380, 381,
+	382, 383, 384, 385, 386, 387, 388, 389, 390, 391, 392,
+	393, 395, 396, 397, 398, 399, 400, 401, 402, 403, 404,
+	405, 406, 407, 408, 410, 411, 412, 413, 414, 415, 416,
+	417, 418, 419, 420, 421, 423, 424, 425, 426, 427, 428,
+	429, 430, 431, 432, 433, 435, 436, 437, 438, 439, 440,
+	441, 442, 443, 444, 446, 447, 448, 449, 450, 451, 452,
+	453, 454, 456, 457, 458, 459, 460, 461, 462, 463, 464,
+	466, 467, 468, 469, 470, 471, 472, 473, 475, 476, 477,
+	478, 479, 480, 481, 482, 484, 485, 486, 487, 488, 489,
+	490, 491, 493, 494, 495, 496, 497, 498, 499, 501, 502,
+	503, 504, 505, 506, 507, 509, 510, 511, 512, 513, 514,
+	515, 517, 518, 519, 520, 521, 522, 524, 525, 526, 527,
+	528, 529, 531, 532, 533, 534, 535, 536, 537, 539, 540,
+	541, 542, 543, 544, 546, 547, 548, 549, 550, 552, 553,
+	554, 555, 556, 557, 559, 560, 561, 562, 563, 564, 566,
+	567, 568, 569, 570, 572, 573, 574, 575, 576, 578, 579,
+	580, 581, 582, 583, 585, 586, 587, 588, 589, 591, 592,
+	593, 594, 595, 597, 598, 599, 600, 601, 603, 604, 605,
+	606, 607, 609, 610, 611, 612, 613, 615, 616, 617, 618,
+	620, 621, 622, 623, 624, 626, 627, 628, 629, 630, 632,
+	633, 634, 635, 637, 638, 639, 640, 641, 643, 644, 645,
+	646, 648, 649, 650, 651, 653, 654, 655, 656, 657, 659,
+	660, 661, 662, 664, 665, 666, 667, 669, 670, 671, 672,
+	674, 675, 676, 677, 679, 680, 681, 682, 684, 685, 686,
+	687, 689, 690, 691, 692, 694, 695, 696, 697, 699, 700,
+	701, 702, 704, 705, 706, 707, 709, 710, 711, 712, 714,
+	715, 716, 717, 719, 720, 721, 723, 724, 725, 726, 728,
+	729, 730, 731, 733, 734, 735, 737, 738, 739, 740, 742,
+	743, 744, 745, 747, 748, 749, 751, 752, 753, 754, 756,
+	757, 758, 760, 761, 762, 763, 765, 766, 767, 769, 770,
+	771, 772, 774, 775, 776, 778, 779, 780, 782, 783, 784,
+	785, 787, 788, 789, 791, 792, 793, 794, 796, 797, 798,
+	800, 801, 802, 804, 805, 806, 808, 809, 810, 811, 813,
+	814, 815, 817, 818, 819, 821, 822, 823, 825, 826, 827,
+	829, 830, 831, 833, 834, 835, 836, 838, 839, 840, 842,
+	843, 844, 846, 847, 848, 850, 851, 852, 854, 855, 856,
+	858, 859, 860, 862, 863, 864, 866, 867, 868, 870, 871,
+	872, 874, 875, 876, 878, 879, 880, 882, 883, 884, 886,
+	887, 888, 890, 891, 893, 894, 895, 897, 898, 899, 901,
+	902, 903, 905, 906, 907, 909, 910, 911, 913, 914, 915,
+	917, 918, 920, 921, 922, 924, 925, 926, 928, 929, 930,
+	932, 933, 935, 936, 937, 939, 940, 941, 943, 944, 945,
+	947, 948, 950, 951, 952, 954, 955, 956, 958, 959, 961,
+	962, 963, 965, 966, 967, 969, 970, 972, 973, 974, 976,
+	977, 978, 980, 981, 983, 984, 985, 987, 988, 990, 991,
+	992, 994, 995, 996, 998, 999, 1001, 1002, 1003, 1005, 1006,
+	1008, 1009, 1010, 1012, 1013, 1015, 1016, 1017, 1019, 1020, 1022,
+	1023,
+};
+
+static const u16 xgamma10_15[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1,
+	1, 1, 1, 2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 4, 4, 4, 4, 5, 5, 5, 5, 6,
+	6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9,
+	9, 9, 10, 10, 10, 11, 11, 11, 12, 12, 12,
+	13, 13, 13, 14, 14, 15, 15, 15, 16, 16, 16,
+	17, 17, 18, 18, 18, 19, 19, 20, 20, 20, 21,
+	21, 22, 22, 22, 23, 23, 24, 24, 25, 25, 25,
+	26, 26, 27, 27, 28, 28, 28, 29, 29, 30, 30,
+	31, 31, 32, 32, 33, 33, 34, 34, 35, 35, 36,
+	36, 37, 37, 38, 38, 39, 39, 40, 40, 41, 41,
+	42, 42, 43, 43, 44, 44, 45, 45, 46, 46, 47,
+	47, 48, 48, 49, 50, 50, 51, 51, 52, 52, 53,
+	53, 54, 55, 55, 56, 56, 57, 57, 58, 59, 59,
+	60, 60, 61, 62, 62, 63, 63, 64, 64, 65, 66,
+	66, 67, 67, 68, 69, 69, 70, 71, 71, 72, 72,
+	73, 74, 74, 75, 76, 76, 77, 77, 78, 79, 79,
+	80, 81, 81, 82, 83, 83, 84, 84, 85, 86, 86,
+	87, 88, 88, 89, 90, 90, 91, 92, 92, 93, 94,
+	94, 95, 96, 97, 97, 98, 99, 99, 100, 101, 101,
+	102, 103, 103, 104, 105, 106, 106, 107, 108, 108, 109,
+	110, 110, 111, 112, 113, 113, 114, 115, 116, 116, 117,
+	118, 118, 119, 120, 121, 121, 122, 123, 124, 124, 125,
+	126, 127, 127, 128, 129, 130, 130, 131, 132, 133, 133,
+	134, 135, 136, 136, 137, 138, 139, 139, 140, 141, 142,
+	143, 143, 144, 145, 146, 146, 147, 148, 149, 150, 150,
+	151, 152, 153, 154, 154, 155, 156, 157, 158, 158, 159,
+	160, 161, 162, 162, 163, 164, 165, 166, 167, 167, 168,
+	169, 170, 171, 171, 172, 173, 174, 175, 176, 176, 177,
+	178, 179, 180, 181, 181, 182, 183, 184, 185, 186, 187,
+	187, 188, 189, 190, 191, 192, 193, 193, 194, 195, 196,
+	197, 198, 199, 199, 200, 201, 202, 203, 204, 205, 206,
+	206, 207, 208, 209, 210, 211, 212, 213, 214, 214, 215,
+	216, 217, 218, 219, 220, 221, 222, 223, 223, 224, 225,
+	226, 227, 228, 229, 230, 231, 232, 233, 233, 234, 235,
+	236, 237, 238, 239, 240, 241, 242, 243, 244, 245, 245,
+	246, 247, 248, 249, 250, 251, 252, 253, 254, 255, 256,
+	257, 258, 259, 260, 261, 261, 262, 263, 264, 265, 266,
+	267, 268, 269, 270, 271, 272, 273, 274, 275, 276, 277,
+	278, 279, 280, 281, 282, 283, 284, 285, 286, 287, 288,
+	289, 290, 291, 292, 293, 293, 294, 295, 296, 297, 298,
+	299, 300, 301, 302, 303, 304, 305, 306, 307, 308, 309,
+	310, 311, 312, 314, 315, 316, 317, 318, 319, 320, 321,
+	322, 323, 324, 325, 326, 327, 328, 329, 330, 331, 332,
+	333, 334, 335, 336, 337, 338, 339, 340, 341, 342, 343,
+	344, 345, 346, 347, 349, 350, 351, 352, 353, 354, 355,
+	356, 357, 358, 359, 360, 361, 362, 363, 364, 365, 366,
+	368, 369, 370, 371, 372, 373, 374, 375, 376, 377, 378,
+	379, 380, 381, 383, 384, 385, 386, 387, 388, 389, 390,
+	391, 392, 393, 395, 396, 397, 398, 399, 400, 401, 402,
+	403, 404, 405, 407, 408, 409, 410, 411, 412, 413, 414,
+	415, 417, 418, 419, 420, 421, 422, 423, 424, 425, 427,
+	428, 429, 430, 431, 432, 433, 434, 436, 437, 438, 439,
+	440, 441, 442, 444, 445, 446, 447, 448, 449, 450, 451,
+	453, 454, 455, 456, 457, 458, 460, 461, 462, 463, 464,
+	465, 466, 468, 469, 470, 471, 472, 473, 475, 476, 477,
+	478, 479, 480, 482, 483, 484, 485, 486, 487, 489, 490,
+	491, 492, 493, 494, 496, 497, 498, 499, 500, 501, 503,
+	504, 505, 506, 507, 509, 510, 511, 512, 513, 515, 516,
+	517, 518, 519, 521, 522, 523, 524, 525, 527, 528, 529,
+	530, 531, 533, 534, 535, 536, 537, 539, 540, 541, 542,
+	543, 545, 546, 547, 548, 550, 551, 552, 553, 554, 556,
+	557, 558, 559, 561, 562, 563, 564, 565, 567, 568, 569,
+	570, 572, 573, 574, 575, 577, 578, 579, 580, 582, 583,
+	584, 585, 587, 588, 589, 590, 591, 593, 594, 595, 596,
+	598, 599, 600, 602, 603, 604, 605, 607, 608, 609, 610,
+	612, 613, 614, 615, 617, 618, 619, 620, 622, 623, 624,
+	626, 627, 628, 629, 631, 632, 633, 634, 636, 637, 638,
+	640, 641, 642, 643, 645, 646, 647, 649, 650, 651, 652,
+	654, 655, 656, 658, 659, 660, 662, 663, 664, 665, 667,
+	668, 669, 671, 672, 673, 675, 676, 677, 678, 680, 681,
+	682, 684, 685, 686, 688, 689, 690, 692, 693, 694, 696,
+	697, 698, 700, 701, 702, 703, 705, 706, 707, 709, 710,
+	711, 713, 714, 715, 717, 718, 719, 721, 722, 723, 725,
+	726, 727, 729, 730, 731, 733, 734, 735, 737, 738, 740,
+	741, 742, 744, 745, 746, 748, 749, 750, 752, 753, 754,
+	756, 757, 758, 760, 761, 763, 764, 765, 767, 768, 769,
+	771, 772, 773, 775, 776, 778, 779, 780, 782, 783, 784,
+	786, 787, 789, 790, 791, 793, 794, 795, 797, 798, 800,
+	801, 802, 804, 805, 806, 808, 809, 811, 812, 813, 815,
+	816, 818, 819, 820, 822, 823, 825, 826, 827, 829, 830,
+	832, 833, 834, 836, 837, 839, 840, 841, 843, 844, 846,
+	847, 848, 850, 851, 853, 854, 855, 857, 858, 860, 861,
+	863, 864, 865, 867, 868, 870, 871, 872, 874, 875, 877,
+	878, 880, 881, 882, 884, 885, 887, 888, 890, 891, 892,
+	894, 895, 897, 898, 900, 901, 902, 904, 905, 907, 908,
+	910, 911, 913, 914, 915, 917, 918, 920, 921, 923, 924,
+	926, 927, 929, 930, 931, 933, 934, 936, 937, 939, 940,
+	942, 943, 945, 946, 947, 949, 950, 952, 953, 955, 956,
+	958, 959, 961, 962, 964, 965, 967, 968, 969, 971, 972,
+	974, 975, 977, 978, 980, 981, 983, 984, 986, 987, 989,
+	990, 992, 993, 995, 996, 998, 999, 1001, 1002, 1004, 1005,
+	1007, 1008, 1010, 1011, 1013, 1014, 1016, 1017, 1019, 1020, 1022,
+	1023,
+};
+
+static const u16 xgamma10_16[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 3, 3, 3, 3, 3, 3, 4, 4, 4,
+	4, 4, 5, 5, 5, 5, 5, 6, 6, 6, 6,
+	7, 7, 7, 7, 8, 8, 8, 8, 9, 9, 9,
+	10, 10, 10, 10, 11, 11, 11, 12, 12, 12, 12,
+	13, 13, 13, 14, 14, 14, 15, 15, 15, 16, 16,
+	16, 17, 17, 17, 18, 18, 18, 19, 19, 19, 20,
+	20, 21, 21, 21, 22, 22, 22, 23, 23, 24, 24,
+	24, 25, 25, 26, 26, 26, 27, 27, 28, 28, 28,
+	29, 29, 30, 30, 31, 31, 31, 32, 32, 33, 33,
+	34, 34, 35, 35, 35, 36, 36, 37, 37, 38, 38,
+	39, 39, 40, 40, 41, 41, 41, 42, 42, 43, 43,
+	44, 44, 45, 45, 46, 46, 47, 47, 48, 48, 49,
+	49, 50, 50, 51, 52, 52, 53, 53, 54, 54, 55,
+	55, 56, 56, 57, 57, 58, 58, 59, 60, 60, 61,
+	61, 62, 62, 63, 63, 64, 65, 65, 66, 66, 67,
+	67, 68, 69, 69, 70, 70, 71, 72, 72, 73, 73,
+	74, 75, 75, 76, 76, 77, 78, 78, 79, 79, 80,
+	81, 81, 82, 82, 83, 84, 84, 85, 86, 86, 87,
+	87, 88, 89, 89, 90, 91, 91, 92, 93, 93, 94,
+	95, 95, 96, 97, 97, 98, 99, 99, 100, 101, 101,
+	102, 103, 103, 104, 105, 105, 106, 107, 107, 108, 109,
+	109, 110, 111, 111, 112, 113, 114, 114, 115, 116, 116,
+	117, 118, 119, 119, 120, 121, 121, 122, 123, 124, 124,
+	125, 126, 126, 127, 128, 129, 129, 130, 131, 132, 132,
+	133, 134, 135, 135, 136, 137, 138, 138, 139, 140, 141,
+	141, 142, 143, 144, 144, 145, 146, 147, 148, 148, 149,
+	150, 151, 151, 152, 153, 154, 155, 155, 156, 157, 158,
+	159, 159, 160, 161, 162, 163, 163, 164, 165, 166, 167,
+	167, 168, 169, 170, 171, 171, 172, 173, 174, 175, 176,
+	176, 177, 178, 179, 180, 181, 181, 182, 183, 184, 185,
+	186, 186, 187, 188, 189, 190, 191, 192, 192, 193, 194,
+	195, 196, 197, 198, 198, 199, 200, 201, 202, 203, 204,
+	204, 205, 206, 207, 208, 209, 210, 211, 212, 212, 213,
+	214, 215, 216, 217, 218, 219, 220, 220, 221, 222, 223,
+	224, 225, 226, 227, 228, 229, 230, 230, 231, 232, 233,
+	234, 235, 236, 237, 238, 239, 240, 241, 242, 242, 243,
+	244, 245, 246, 247, 248, 249, 250, 251, 252, 253, 254,
+	255, 256, 257, 258, 258, 259, 260, 261, 262, 263, 264,
+	265, 266, 267, 268, 269, 270, 271, 272, 273, 274, 275,
+	276, 277, 278, 279, 280, 281, 282, 283, 284, 285, 286,
+	287, 288, 289, 290, 291, 292, 293, 294, 295, 296, 297,
+	298, 299, 300, 301, 302, 303, 304, 305, 306, 307, 308,
+	309, 310, 311, 312, 313, 314, 315, 316, 317, 318, 319,
+	320, 321, 322, 323, 324, 325, 326, 327, 329, 330, 331,
+	332, 333, 334, 335, 336, 337, 338, 339, 340, 341, 342,
+	343, 344, 345, 346, 348, 349, 350, 351, 352, 353, 354,
+	355, 356, 357, 358, 359, 360, 362, 363, 364, 365, 366,
+	367, 368, 369, 370, 371, 372, 374, 375, 376, 377, 378,
+	379, 380, 381, 382, 383, 385, 386, 387, 388, 389, 390,
+	391, 392, 393, 395, 396, 397, 398, 399, 400, 401, 402,
+	404, 405, 406, 407, 408, 409, 410, 411, 413, 414, 415,
+	416, 417, 418, 419, 421, 422, 423, 424, 425, 426, 428,
+	429, 430, 431, 432, 433, 434, 436, 437, 438, 439, 440,
+	441, 443, 444, 445, 446, 447, 448, 450, 451, 452, 453,
+	454, 456, 457, 458, 459, 460, 461, 463, 464, 465, 466,
+	467, 469, 470, 471, 472, 473, 475, 476, 477, 478, 479,
+	481, 482, 483, 484, 485, 487, 488, 489, 490, 491, 493,
+	494, 495, 496, 498, 499, 500, 501, 502, 504, 505, 506,
+	507, 509, 510, 511, 512, 514, 515, 516, 517, 519, 520,
+	521, 522, 523, 525, 526, 527, 528, 530, 531, 532, 533,
+	535, 536, 537, 538, 540, 541, 542, 544, 545, 546, 547,
+	549, 550, 551, 552, 554, 555, 556, 557, 559, 560, 561,
+	563, 564, 565, 566, 568, 569, 570, 572, 573, 574, 575,
+	577, 578, 579, 581, 582, 583, 584, 586, 587, 588, 590,
+	591, 592, 594, 595, 596, 598, 599, 600, 601, 603, 604,
+	605, 607, 608, 609, 611, 612, 613, 615, 616, 617, 619,
+	620, 621, 623, 624, 625, 627, 628, 629, 631, 632, 633,
+	635, 636, 637, 639, 640, 641, 643, 644, 645, 647, 648,
+	649, 651, 652, 653, 655, 656, 657, 659, 660, 662, 663,
+	664, 666, 667, 668, 670, 671, 672, 674, 675, 677, 678,
+	679, 681, 682, 683, 685, 686, 688, 689, 690, 692, 693,
+	694, 696, 697, 699, 700, 701, 703, 704, 706, 707, 708,
+	710, 711, 712, 714, 715, 717, 718, 719, 721, 722, 724,
+	725, 727, 728, 729, 731, 732, 734, 735, 736, 738, 739,
+	741, 742, 743, 745, 746, 748, 749, 751, 752, 753, 755,
+	756, 758, 759, 761, 762, 763, 765, 766, 768, 769, 771,
+	772, 774, 775, 776, 778, 779, 781, 782, 784, 785, 787,
+	788, 789, 791, 792, 794, 795, 797, 798, 800, 801, 803,
+	804, 805, 807, 808, 810, 811, 813, 814, 816, 817, 819,
+	820, 822, 823, 825, 826, 827, 829, 830, 832, 833, 835,
+	836, 838, 839, 841, 842, 844, 845, 847, 848, 850, 851,
+	853, 854, 856, 857, 859, 860, 862, 863, 865, 866, 868,
+	869, 871, 872, 874, 875, 877, 878, 880, 881, 883, 884,
+	886, 887, 889, 890, 892, 893, 895, 897, 898, 900, 901,
+	903, 904, 906, 907, 909, 910, 912, 913, 915, 916, 918,
+	919, 921, 923, 924, 926, 927, 929, 930, 932, 933, 935,
+	936, 938, 940, 941, 943, 944, 946, 947, 949, 950, 952,
+	954, 955, 957, 958, 960, 961, 963, 964, 966, 968, 969,
+	971, 972, 974, 975, 977, 979, 980, 982, 983, 985, 986,
+	988, 990, 991, 993, 994, 996, 998, 999, 1001, 1002, 1004,
+	1005, 1007, 1009, 1010, 1012, 1013, 1015, 1017, 1018, 1020, 1021,
+	1023,
+};
+
+static const u16 xgamma10_17[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 3, 3, 4, 4, 4, 4, 4, 4, 5,
+	5, 5, 5, 5, 6, 6, 6, 6, 6, 7, 7,
+	7, 7, 8, 8, 8, 8, 8, 9, 9, 9, 9,
+	10, 10, 10, 10, 11, 11, 11, 12, 12, 12, 12,
+	13, 13, 13, 13, 14, 14, 14, 15, 15, 15, 15,
+	16, 16, 16, 17, 17, 17, 18, 18, 18, 19, 19,
+	19, 20, 20, 20, 21, 21, 21, 22, 22, 22, 23,
+	23, 23, 24, 24, 25, 25, 25, 26, 26, 26, 27,
+	27, 28, 28, 28, 29, 29, 29, 30, 30, 31, 31,
+	31, 32, 32, 33, 33, 34, 34, 34, 35, 35, 36,
+	36, 37, 37, 37, 38, 38, 39, 39, 40, 40, 40,
+	41, 41, 42, 42, 43, 43, 44, 44, 45, 45, 46,
+	46, 46, 47, 47, 48, 48, 49, 49, 50, 50, 51,
+	51, 52, 52, 53, 53, 54, 54, 55, 55, 56, 56,
+	57, 57, 58, 58, 59, 60, 60, 61, 61, 62, 62,
+	63, 63, 64, 64, 65, 65, 66, 67, 67, 68, 68,
+	69, 69, 70, 70, 71, 72, 72, 73, 73, 74, 74,
+	75, 76, 76, 77, 77, 78, 79, 79, 80, 80, 81,
+	82, 82, 83, 83, 84, 85, 85, 86, 86, 87, 88,
+	88, 89, 89, 90, 91, 91, 92, 93, 93, 94, 95,
+	95, 96, 96, 97, 98, 98, 99, 100, 100, 101, 102,
+	102, 103, 104, 104, 105, 106, 106, 107, 108, 108, 109,
+	110, 110, 111, 112, 112, 113, 114, 114, 115, 116, 116,
+	117, 118, 119, 119, 120, 121, 121, 122, 123, 124, 124,
+	125, 126, 126, 127, 128, 129, 129, 130, 131, 131, 132,
+	133, 134, 134, 135, 136, 137, 137, 138, 139, 140, 140,
+	141, 142, 143, 143, 144, 145, 146, 146, 147, 148, 149,
+	149, 150, 151, 152, 153, 153, 154, 155, 156, 156, 157,
+	158, 159, 160, 160, 161, 162, 163, 164, 164, 165, 166,
+	167, 168, 168, 169, 170, 171, 172, 172, 173, 174, 175,
+	176, 177, 177, 178, 179, 180, 181, 182, 182, 183, 184,
+	185, 186, 187, 187, 188, 189, 190, 191, 192, 193, 193,
+	194, 195, 196, 197, 198, 199, 199, 200, 201, 202, 203,
+	204, 205, 206, 206, 207, 208, 209, 210, 211, 212, 213,
+	213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 222,
+	223, 224, 225, 226, 227, 228, 229, 230, 231, 232, 233,
+	233, 234, 235, 236, 237, 238, 239, 240, 241, 242, 243,
+	244, 245, 246, 247, 248, 248, 249, 250, 251, 252, 253,
+	254, 255, 256, 257, 258, 259, 260, 261, 262, 263, 264,
+	265, 266, 267, 268, 269, 270, 271, 272, 273, 274, 275,
+	276, 277, 278, 279, 280, 281, 282, 283, 284, 285, 286,
+	287, 288, 289, 290, 291, 292, 293, 294, 295, 296, 297,
+	298, 299, 300, 301, 302, 303, 304, 305, 306, 307, 308,
+	309, 310, 311, 312, 313, 314, 315, 316, 317, 319, 320,
+	321, 322, 323, 324, 325, 326, 327, 328, 329, 330, 331,
+	332, 333, 334, 336, 337, 338, 339, 340, 341, 342, 343,
+	344, 345, 346, 347, 349, 350, 351, 352, 353, 354, 355,
+	356, 357, 358, 360, 361, 362, 363, 364, 365, 366, 367,
+	368, 370, 371, 372, 373, 374, 375, 376, 377, 379, 380,
+	381, 382, 383, 384, 385, 386, 388, 389, 390, 391, 392,
+	393, 394, 396, 397, 398, 399, 400, 401, 403, 404, 405,
+	406, 407, 408, 409, 411, 412, 413, 414, 415, 417, 418,
+	419, 420, 421, 422, 424, 425, 426, 427, 428, 430, 431,
+	432, 433, 434, 435, 437, 438, 439, 440, 441, 443, 444,
+	445, 446, 448, 449, 450, 451, 452, 454, 455, 456, 457,
+	458, 460, 461, 462, 463, 465, 466, 467, 468, 469, 471,
+	472, 473, 474, 476, 477, 478, 479, 481, 482, 483, 484,
+	486, 487, 488, 489, 491, 492, 493, 494, 496, 497, 498,
+	499, 501, 502, 503, 505, 506, 507, 508, 510, 511, 512,
+	513, 515, 516, 517, 519, 520, 521, 522, 524, 525, 526,
+	528, 529, 530, 532, 533, 534, 535, 537, 538, 539, 541,
+	542, 543, 545, 546, 547, 549, 550, 551, 552, 554, 555,
+	556, 558, 559, 560, 562, 563, 564, 566, 567, 568, 570,
+	571, 572, 574, 575, 576, 578, 579, 580, 582, 583, 584,
+	586, 587, 589, 590, 591, 593, 594, 595, 597, 598, 599,
+	601, 602, 604, 605, 606, 608, 609, 610, 612, 613, 615,
+	616, 617, 619, 620, 621, 623, 624, 626, 627, 628, 630,
+	631, 633, 634, 635, 637, 638, 640, 641, 642, 644, 645,
+	647, 648, 649, 651, 652, 654, 655, 656, 658, 659, 661,
+	662, 664, 665, 666, 668, 669, 671, 672, 674, 675, 676,
+	678, 679, 681, 682, 684, 685, 686, 688, 689, 691, 692,
+	694, 695, 697, 698, 699, 701, 702, 704, 705, 707, 708,
+	710, 711, 713, 714, 716, 717, 718, 720, 721, 723, 724,
+	726, 727, 729, 730, 732, 733, 735, 736, 738, 739, 741,
+	742, 744, 745, 747, 748, 750, 751, 753, 754, 756, 757,
+	759, 760, 762, 763, 765, 766, 768, 769, 771, 772, 774,
+	775, 777, 778, 780, 781, 783, 784, 786, 787, 789, 790,
+	792, 793, 795, 797, 798, 800, 801, 803, 804, 806, 807,
+	809, 810, 812, 814, 815, 817, 818, 820, 821, 823, 824,
+	826, 827, 829, 831, 832, 834, 835, 837, 838, 840, 842,
+	843, 845, 846, 848, 849, 851, 853, 854, 856, 857, 859,
+	860, 862, 864, 865, 867, 868, 870, 872, 873, 875, 876,
+	878, 880, 881, 883, 884, 886, 888, 889, 891, 892, 894,
+	896, 897, 899, 900, 902, 904, 905, 907, 908, 910, 912,
+	913, 915, 917, 918, 920, 921, 923, 925, 926, 928, 930,
+	931, 933, 935, 936, 938, 939, 941, 943, 944, 946, 948,
+	949, 951, 953, 954, 956, 958, 959, 961, 963, 964, 966,
+	968, 969, 971, 973, 974, 976, 978, 979, 981, 983, 984,
+	986, 988, 989, 991, 993, 994, 996, 998, 999, 1001, 1003,
+	1004, 1006, 1008, 1009, 1011, 1013, 1015, 1016, 1018, 1020, 1021,
+	1023,
+};
+
+static const u16 xgamma10_18[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5,
+	5, 5, 6, 6, 6, 6, 6, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9,
+	10, 10, 10, 10, 11, 11, 11, 11, 12, 12, 12,
+	12, 13, 13, 13, 13, 14, 14, 14, 14, 15, 15,
+	15, 16, 16, 16, 16, 17, 17, 17, 18, 18, 18,
+	18, 19, 19, 19, 20, 20, 20, 21, 21, 21, 22,
+	22, 22, 23, 23, 23, 24, 24, 24, 25, 25, 25,
+	26, 26, 26, 27, 27, 27, 28, 28, 29, 29, 29,
+	30, 30, 30, 31, 31, 32, 32, 32, 33, 33, 33,
+	34, 34, 35, 35, 35, 36, 36, 37, 37, 38, 38,
+	38, 39, 39, 40, 40, 40, 41, 41, 42, 42, 43,
+	43, 43, 44, 44, 45, 45, 46, 46, 47, 47, 48,
+	48, 48, 49, 49, 50, 50, 51, 51, 52, 52, 53,
+	53, 54, 54, 55, 55, 56, 56, 57, 57, 58, 58,
+	59, 59, 60, 60, 61, 61, 62, 62, 63, 63, 64,
+	64, 65, 65, 66, 66, 67, 68, 68, 69, 69, 70,
+	70, 71, 71, 72, 72, 73, 74, 74, 75, 75, 76,
+	76, 77, 78, 78, 79, 79, 80, 80, 81, 82, 82,
+	83, 83, 84, 85, 85, 86, 86, 87, 88, 88, 89,
+	89, 90, 91, 91, 92, 92, 93, 94, 94, 95, 96,
+	96, 97, 97, 98, 99, 99, 100, 101, 101, 102, 103,
+	103, 104, 104, 105, 106, 106, 107, 108, 108, 109, 110,
+	110, 111, 112, 112, 113, 114, 114, 115, 116, 117, 117,
+	118, 119, 119, 120, 121, 121, 122, 123, 123, 124, 125,
+	126, 126, 127, 128, 128, 129, 130, 131, 131, 132, 133,
+	133, 134, 135, 136, 136, 137, 138, 139, 139, 140, 141,
+	142, 142, 143, 144, 145, 145, 146, 147, 148, 148, 149,
+	150, 151, 151, 152, 153, 154, 155, 155, 156, 157, 158,
+	158, 159, 160, 161, 162, 162, 163, 164, 165, 166, 166,
+	167, 168, 169, 170, 170, 171, 172, 173, 174, 175, 175,
+	176, 177, 178, 179, 179, 180, 181, 182, 183, 184, 184,
+	185, 186, 187, 188, 189, 190, 190, 191, 192, 193, 194,
+	195, 196, 196, 197, 198, 199, 200, 201, 202, 203, 203,
+	204, 205, 206, 207, 208, 209, 210, 210, 211, 212, 213,
+	214, 215, 216, 217, 218, 219, 219, 220, 221, 222, 223,
+	224, 225, 226, 227, 228, 229, 230, 230, 231, 232, 233,
+	234, 235, 236, 237, 238, 239, 240, 241, 242, 243, 244,
+	245, 246, 247, 247, 248, 249, 250, 251, 252, 253, 254,
+	255, 256, 257, 258, 259, 260, 261, 262, 263, 264, 265,
+	266, 267, 268, 269, 270, 271, 272, 273, 274, 275, 276,
+	277, 278, 279, 280, 281, 282, 283, 284, 285, 286, 287,
+	288, 289, 290, 291, 292, 293, 294, 295, 296, 297, 298,
+	299, 301, 302, 303, 304, 305, 306, 307, 308, 309, 310,
+	311, 312, 313, 314, 315, 316, 317, 319, 320, 321, 322,
+	323, 324, 325, 326, 327, 328, 329, 330, 331, 333, 334,
+	335, 336, 337, 338, 339, 340, 341, 342, 344, 345, 346,
+	347, 348, 349, 350, 351, 353, 354, 355, 356, 357, 358,
+	359, 360, 362, 363, 364, 365, 366, 367, 368, 370, 371,
+	372, 373, 374, 375, 376, 378, 379, 380, 381, 382, 383,
+	385, 386, 387, 388, 389, 390, 392, 393, 394, 395, 396,
+	397, 399, 400, 401, 402, 403, 405, 406, 407, 408, 409,
+	411, 412, 413, 414, 415, 417, 418, 419, 420, 421, 423,
+	424, 425, 426, 427, 429, 430, 431, 432, 434, 435, 436,
+	437, 439, 440, 441, 442, 443, 445, 446, 447, 448, 450,
+	451, 452, 453, 455, 456, 457, 458, 460, 461, 462, 464,
+	465, 466, 467, 469, 470, 471, 472, 474, 475, 476, 478,
+	479, 480, 481, 483, 484, 485, 487, 488, 489, 490, 492,
+	493, 494, 496, 497, 498, 500, 501, 502, 504, 505, 506,
+	507, 509, 510, 511, 513, 514, 515, 517, 518, 519, 521,
+	522, 523, 525, 526, 527, 529, 530, 531, 533, 534, 535,
+	537, 538, 540, 541, 542, 544, 545, 546, 548, 549, 550,
+	552, 553, 555, 556, 557, 559, 560, 561, 563, 564, 566,
+	567, 568, 570, 571, 572, 574, 575, 577, 578, 579, 581,
+	582, 584, 585, 586, 588, 589, 591, 592, 594, 595, 596,
+	598, 599, 601, 602, 603, 605, 606, 608, 609, 611, 612,
+	613, 615, 616, 618, 619, 621, 622, 624, 625, 626, 628,
+	629, 631, 632, 634, 635, 637, 638, 640, 641, 642, 644,
+	645, 647, 648, 650, 651, 653, 654, 656, 657, 659, 660,
+	662, 663, 665, 666, 668, 669, 671, 672, 673, 675, 676,
+	678, 679, 681, 682, 684, 686, 687, 689, 690, 692, 693,
+	695, 696, 698, 699, 701, 702, 704, 705, 707, 708, 710,
+	711, 713, 714, 716, 717, 719, 721, 722, 724, 725, 727,
+	728, 730, 731, 733, 734, 736, 738, 739, 741, 742, 744,
+	745, 747, 749, 750, 752, 753, 755, 756, 758, 760, 761,
+	763, 764, 766, 767, 769, 771, 772, 774, 775, 777, 779,
+	780, 782, 783, 785, 787, 788, 790, 791, 793, 795, 796,
+	798, 799, 801, 803, 804, 806, 807, 809, 811, 812, 814,
+	816, 817, 819, 820, 822, 824, 825, 827, 829, 830, 832,
+	834, 835, 837, 839, 840, 842, 843, 845, 847, 848, 850,
+	852, 853, 855, 857, 858, 860, 862, 863, 865, 867, 868,
+	870, 872, 873, 875, 877, 878, 880, 882, 884, 885, 887,
+	889, 890, 892, 894, 895, 897, 899, 900, 902, 904, 906,
+	907, 909, 911, 912, 914, 916, 918, 919, 921, 923, 924,
+	926, 928, 930, 931, 933, 935, 936, 938, 940, 942, 943,
+	945, 947, 949, 950, 952, 954, 956, 957, 959, 961, 963,
+	964, 966, 968, 970, 971, 973, 975, 977, 978, 980, 982,
+	984, 986, 987, 989, 991, 993, 994, 996, 998, 1000, 1002,
+	1003, 1005, 1007, 1009, 1010, 1012, 1014, 1016, 1018, 1019, 1021,
+	1023,
+};
+
+static const u16 xgamma10_19[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	3, 3, 3, 3, 3, 3, 3, 3, 4, 4, 4,
+	4, 4, 4, 4, 5, 5, 5, 5, 5, 5, 5,
+	6, 6, 6, 6, 6, 6, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9,
+	10, 10, 10, 10, 11, 11, 11, 11, 11, 12, 12,
+	12, 12, 13, 13, 13, 13, 14, 14, 14, 14, 15,
+	15, 15, 15, 16, 16, 16, 16, 17, 17, 17, 17,
+	18, 18, 18, 19, 19, 19, 19, 20, 20, 20, 21,
+	21, 21, 22, 22, 22, 22, 23, 23, 23, 24, 24,
+	24, 25, 25, 25, 26, 26, 26, 27, 27, 27, 28,
+	28, 28, 29, 29, 29, 30, 30, 30, 31, 31, 32,
+	32, 32, 33, 33, 33, 34, 34, 35, 35, 35, 36,
+	36, 36, 37, 37, 38, 38, 38, 39, 39, 40, 40,
+	41, 41, 41, 42, 42, 43, 43, 43, 44, 44, 45,
+	45, 46, 46, 46, 47, 47, 48, 48, 49, 49, 50,
+	50, 51, 51, 51, 52, 52, 53, 53, 54, 54, 55,
+	55, 56, 56, 57, 57, 58, 58, 59, 59, 60, 60,
+	61, 61, 62, 62, 63, 63, 64, 64, 65, 65, 66,
+	66, 67, 67, 68, 68, 69, 69, 70, 70, 71, 71,
+	72, 72, 73, 74, 74, 75, 75, 76, 76, 77, 77,
+	78, 79, 79, 80, 80, 81, 81, 82, 83, 83, 84,
+	84, 85, 85, 86, 87, 87, 88, 88, 89, 90, 90,
+	91, 91, 92, 93, 93, 94, 94, 95, 96, 96, 97,
+	98, 98, 99, 99, 100, 101, 101, 102, 103, 103, 104,
+	105, 105, 106, 107, 107, 108, 108, 109, 110, 110, 111,
+	112, 112, 113, 114, 114, 115, 116, 116, 117, 118, 119,
+	119, 120, 121, 121, 122, 123, 123, 124, 125, 125, 126,
+	127, 128, 128, 129, 130, 130, 131, 132, 133, 133, 134,
+	135, 135, 136, 137, 138, 138, 139, 140, 141, 141, 142,
+	143, 144, 144, 145, 146, 147, 147, 148, 149, 150, 150,
+	151, 152, 153, 154, 154, 155, 156, 157, 157, 158, 159,
+	160, 161, 161, 162, 163, 164, 165, 165, 166, 167, 168,
+	169, 169, 170, 171, 172, 173, 173, 174, 175, 176, 177,
+	178, 178, 179, 180, 181, 182, 183, 183, 184, 185, 186,
+	187, 188, 188, 189, 190, 191, 192, 193, 194, 195, 195,
+	196, 197, 198, 199, 200, 201, 201, 202, 203, 204, 205,
+	206, 207, 208, 209, 209, 210, 211, 212, 213, 214, 215,
+	216, 217, 218, 219, 219, 220, 221, 222, 223, 224, 225,
+	226, 227, 228, 229, 230, 231, 232, 232, 233, 234, 235,
+	236, 237, 238, 239, 240, 241, 242, 243, 244, 245, 246,
+	247, 248, 249, 250, 251, 252, 253, 254, 255, 256, 257,
+	258, 259, 260, 261, 262, 263, 264, 265, 266, 267, 268,
+	269, 270, 271, 272, 273, 274, 275, 276, 277, 278, 279,
+	280, 281, 282, 283, 284, 285, 286, 287, 288, 289, 290,
+	291, 292, 293, 294, 295, 296, 297, 299, 300, 301, 302,
+	303, 304, 305, 306, 307, 308, 309, 310, 311, 312, 314,
+	315, 316, 317, 318, 319, 320, 321, 322, 323, 324, 326,
+	327, 328, 329, 330, 331, 332, 333, 334, 336, 337, 338,
+	339, 340, 341, 342, 343, 345, 346, 347, 348, 349, 350,
+	351, 353, 354, 355, 356, 357, 358, 360, 361, 362, 363,
+	364, 365, 367, 368, 369, 370, 371, 372, 374, 375, 376,
+	377, 378, 379, 381, 382, 383, 384, 385, 387, 388, 389,
+	390, 391, 393, 394, 395, 396, 397, 399, 400, 401, 402,
+	404, 405, 406, 407, 408, 410, 411, 412, 413, 415, 416,
+	417, 418, 420, 421, 422, 423, 425, 426, 427, 428, 430,
+	431, 432, 433, 435, 436, 437, 439, 440, 441, 442, 444,
+	445, 446, 447, 449, 450, 451, 453, 454, 455, 456, 458,
+	459, 460, 462, 463, 464, 466, 467, 468, 470, 471, 472,
+	473, 475, 476, 477, 479, 480, 481, 483, 484, 485, 487,
+	488, 489, 491, 492, 493, 495, 496, 498, 499, 500, 502,
+	503, 504, 506, 507, 508, 510, 511, 512, 514, 515, 517,
+	518, 519, 521, 522, 523, 525, 526, 528, 529, 530, 532,
+	533, 535, 536, 537, 539, 540, 542, 543, 544, 546, 547,
+	549, 550, 551, 553, 554, 556, 557, 559, 560, 561, 563,
+	564, 566, 567, 569, 570, 572, 573, 574, 576, 577, 579,
+	580, 582, 583, 585, 586, 587, 589, 590, 592, 593, 595,
+	596, 598, 599, 601, 602, 604, 605, 607, 608, 610, 611,
+	613, 614, 616, 617, 619, 620, 622, 623, 625, 626, 628,
+	629, 631, 632, 634, 635, 637, 638, 640, 641, 643, 644,
+	646, 647, 649, 650, 652, 653, 655, 656, 658, 660, 661,
+	663, 664, 666, 667, 669, 670, 672, 674, 675, 677, 678,
+	680, 681, 683, 684, 686, 688, 689, 691, 692, 694, 696,
+	697, 699, 700, 702, 703, 705, 707, 708, 710, 711, 713,
+	715, 716, 718, 719, 721, 723, 724, 726, 728, 729, 731,
+	732, 734, 736, 737, 739, 741, 742, 744, 745, 747, 749,
+	750, 752, 754, 755, 757, 759, 760, 762, 764, 765, 767,
+	768, 770, 772, 773, 775, 777, 778, 780, 782, 783, 785,
+	787, 789, 790, 792, 794, 795, 797, 799, 800, 802, 804,
+	805, 807, 809, 810, 812, 814, 816, 817, 819, 821, 822,
+	824, 826, 828, 829, 831, 833, 834, 836, 838, 840, 841,
+	843, 845, 847, 848, 850, 852, 854, 855, 857, 859, 861,
+	862, 864, 866, 868, 869, 871, 873, 875, 876, 878, 880,
+	882, 883, 885, 887, 889, 891, 892, 894, 896, 898, 899,
+	901, 903, 905, 907, 908, 910, 912, 914, 916, 917, 919,
+	921, 923, 925, 926, 928, 930, 932, 934, 936, 937, 939,
+	941, 943, 945, 947, 948, 950, 952, 954, 956, 958, 959,
+	961, 963, 965, 967, 969, 970, 972, 974, 976, 978, 980,
+	982, 983, 985, 987, 989, 991, 993, 995, 997, 998, 1000,
+	1002, 1004, 1006, 1008, 1010, 1012, 1014, 1015, 1017, 1019, 1021,
+	1023,
+};
+
+static const u16 xgamma10_20[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 4, 4, 4, 4, 4, 4,
+	4, 4, 5, 5, 5, 5, 5, 5, 5, 5, 6,
+	6, 6, 6, 6, 6, 7, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9,
+	10, 10, 10, 10, 10, 11, 11, 11, 11, 11, 12,
+	12, 12, 12, 12, 13, 13, 13, 13, 14, 14, 14,
+	14, 15, 15, 15, 15, 16, 16, 16, 16, 17, 17,
+	17, 17, 18, 18, 18, 18, 19, 19, 19, 19, 20,
+	20, 20, 21, 21, 21, 21, 22, 22, 22, 23, 23,
+	23, 23, 24, 24, 24, 25, 25, 25, 26, 26, 26,
+	27, 27, 27, 28, 28, 28, 29, 29, 29, 30, 30,
+	30, 31, 31, 31, 32, 32, 32, 33, 33, 33, 34,
+	34, 35, 35, 35, 36, 36, 36, 37, 37, 38, 38,
+	38, 39, 39, 39, 40, 40, 41, 41, 41, 42, 42,
+	43, 43, 44, 44, 44, 45, 45, 46, 46, 46, 47,
+	47, 48, 48, 49, 49, 49, 50, 50, 51, 51, 52,
+	52, 53, 53, 54, 54, 54, 55, 55, 56, 56, 57,
+	57, 58, 58, 59, 59, 60, 60, 61, 61, 62, 62,
+	63, 63, 64, 64, 65, 65, 66, 66, 67, 67, 68,
+	68, 69, 69, 70, 70, 71, 71, 72, 72, 73, 73,
+	74, 74, 75, 76, 76, 77, 77, 78, 78, 79, 79,
+	80, 81, 81, 82, 82, 83, 83, 84, 84, 85, 86,
+	86, 87, 87, 88, 89, 89, 90, 90, 91, 92, 92,
+	93, 93, 94, 95, 95, 96, 96, 97, 98, 98, 99,
+	99, 100, 101, 101, 102, 103, 103, 104, 105, 105, 106,
+	106, 107, 108, 108, 109, 110, 110, 111, 112, 112, 113,
+	114, 114, 115, 116, 116, 117, 118, 118, 119, 120, 120,
+	121, 122, 122, 123, 124, 125, 125, 126, 127, 127, 128,
+	129, 130, 130, 131, 132, 132, 133, 134, 135, 135, 136,
+	137, 137, 138, 139, 140, 140, 141, 142, 143, 143, 144,
+	145, 146, 146, 147, 148, 149, 149, 150, 151, 152, 153,
+	153, 154, 155, 156, 156, 157, 158, 159, 160, 160, 161,
+	162, 163, 164, 164, 165, 166, 167, 168, 168, 169, 170,
+	171, 172, 172, 173, 174, 175, 176, 177, 177, 178, 179,
+	180, 181, 182, 182, 183, 184, 185, 186, 187, 188, 188,
+	189, 190, 191, 192, 193, 194, 194, 195, 196, 197, 198,
+	199, 200, 201, 201, 202, 203, 204, 205, 206, 207, 208,
+	209, 210, 210, 211, 212, 213, 214, 215, 216, 217, 218,
+	219, 220, 221, 221, 222, 223, 224, 225, 226, 227, 228,
+	229, 230, 231, 232, 233, 234, 235, 236, 237, 238, 239,
+	240, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249,
+	250, 251, 252, 253, 254, 255, 256, 257, 258, 259, 260,
+	261, 262, 263, 264, 265, 266, 267, 268, 269, 270, 271,
+	273, 274, 275, 276, 277, 278, 279, 280, 281, 282, 283,
+	284, 285, 286, 287, 288, 289, 290, 291, 292, 294, 295,
+	296, 297, 298, 299, 300, 301, 302, 303, 304, 305, 307,
+	308, 309, 310, 311, 312, 313, 314, 315, 316, 318, 319,
+	320, 321, 322, 323, 324, 325, 327, 328, 329, 330, 331,
+	332, 333, 335, 336, 337, 338, 339, 340, 341, 343, 344,
+	345, 346, 347, 348, 350, 351, 352, 353, 354, 355, 357,
+	358, 359, 360, 361, 363, 364, 365, 366, 367, 369, 370,
+	371, 372, 373, 375, 376, 377, 378, 379, 381, 382, 383,
+	384, 386, 387, 388, 389, 390, 392, 393, 394, 395, 397,
+	398, 399, 400, 402, 403, 404, 405, 407, 408, 409, 410,
+	412, 413, 414, 416, 417, 418, 419, 421, 422, 423, 425,
+	426, 427, 428, 430, 431, 432, 434, 435, 436, 437, 439,
+	440, 441, 443, 444, 445, 447, 448, 449, 451, 452, 453,
+	455, 456, 457, 459, 460, 461, 463, 464, 465, 467, 468,
+	469, 471, 472, 474, 475, 476, 478, 479, 480, 482, 483,
+	484, 486, 487, 489, 490, 491, 493, 494, 496, 497, 498,
+	500, 501, 503, 504, 505, 507, 508, 510, 511, 512, 514,
+	515, 517, 518, 519, 521, 522, 524, 525, 527, 528, 530,
+	531, 532, 534, 535, 537, 538, 540, 541, 543, 544, 545,
+	547, 548, 550, 551, 553, 554, 556, 557, 559, 560, 562,
+	563, 565, 566, 568, 569, 571, 572, 574, 575, 577, 578,
+	580, 581, 583, 584, 586, 587, 589, 590, 592, 593, 595,
+	596, 598, 599, 601, 602, 604, 605, 607, 609, 610, 612,
+	613, 615, 616, 618, 619, 621, 622, 624, 626, 627, 629,
+	630, 632, 633, 635, 637, 638, 640, 641, 643, 645, 646,
+	648, 649, 651, 652, 654, 656, 657, 659, 660, 662, 664,
+	665, 667, 669, 670, 672, 673, 675, 677, 678, 680, 682,
+	683, 685, 686, 688, 690, 691, 693, 695, 696, 698, 700,
+	701, 703, 705, 706, 708, 710, 711, 713, 715, 716, 718,
+	720, 721, 723, 725, 726, 728, 730, 731, 733, 735, 736,
+	738, 740, 742, 743, 745, 747, 748, 750, 752, 754, 755,
+	757, 759, 760, 762, 764, 766, 767, 769, 771, 773, 774,
+	776, 778, 780, 781, 783, 785, 787, 788, 790, 792, 794,
+	795, 797, 799, 801, 802, 804, 806, 808, 809, 811, 813,
+	815, 817, 818, 820, 822, 824, 826, 827, 829, 831, 833,
+	835, 836, 838, 840, 842, 844, 845, 847, 849, 851, 853,
+	855, 856, 858, 860, 862, 864, 866, 867, 869, 871, 873,
+	875, 877, 878, 880, 882, 884, 886, 888, 890, 892, 893,
+	895, 897, 899, 901, 903, 905, 907, 908, 910, 912, 914,
+	916, 918, 920, 922, 924, 925, 927, 929, 931, 933, 935,
+	937, 939, 941, 943, 945, 946, 948, 950, 952, 954, 956,
+	958, 960, 962, 964, 966, 968, 970, 972, 974, 976, 978,
+	979, 981, 983, 985, 987, 989, 991, 993, 995, 997, 999,
+	1001, 1003, 1005, 1007, 1009, 1011, 1013, 1015, 1017, 1019, 1021,
+	1023,
+};
+
+static const u16 xgamma10_21[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 5, 5, 5, 5, 5, 5, 5, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9,
+	9, 10, 10, 10, 10, 10, 11, 11, 11, 11, 11,
+	12, 12, 12, 12, 12, 13, 13, 13, 13, 13, 14,
+	14, 14, 14, 15, 15, 15, 15, 15, 16, 16, 16,
+	16, 17, 17, 17, 17, 18, 18, 18, 18, 19, 19,
+	19, 19, 20, 20, 20, 21, 21, 21, 21, 22, 22,
+	22, 22, 23, 23, 23, 24, 24, 24, 24, 25, 25,
+	25, 26, 26, 26, 27, 27, 27, 28, 28, 28, 29,
+	29, 29, 29, 30, 30, 30, 31, 31, 31, 32, 32,
+	33, 33, 33, 34, 34, 34, 35, 35, 35, 36, 36,
+	36, 37, 37, 38, 38, 38, 39, 39, 39, 40, 40,
+	41, 41, 41, 42, 42, 43, 43, 43, 44, 44, 45,
+	45, 45, 46, 46, 47, 47, 47, 48, 48, 49, 49,
+	50, 50, 50, 51, 51, 52, 52, 53, 53, 54, 54,
+	54, 55, 55, 56, 56, 57, 57, 58, 58, 59, 59,
+	59, 60, 60, 61, 61, 62, 62, 63, 63, 64, 64,
+	65, 65, 66, 66, 67, 67, 68, 68, 69, 69, 70,
+	70, 71, 71, 72, 72, 73, 74, 74, 75, 75, 76,
+	76, 77, 77, 78, 78, 79, 79, 80, 81, 81, 82,
+	82, 83, 83, 84, 85, 85, 86, 86, 87, 87, 88,
+	89, 89, 90, 90, 91, 91, 92, 93, 93, 94, 94,
+	95, 96, 96, 97, 97, 98, 99, 99, 100, 101, 101,
+	102, 102, 103, 104, 104, 105, 106, 106, 107, 108, 108,
+	109, 110, 110, 111, 111, 112, 113, 113, 114, 115, 115,
+	116, 117, 117, 118, 119, 120, 120, 121, 122, 122, 123,
+	124, 124, 125, 126, 126, 127, 128, 129, 129, 130, 131,
+	131, 132, 133, 134, 134, 135, 136, 136, 137, 138, 139,
+	139, 140, 141, 142, 142, 143, 144, 145, 145, 146, 147,
+	148, 148, 149, 150, 151, 152, 152, 153, 154, 155, 155,
+	156, 157, 158, 159, 159, 160, 161, 162, 163, 163, 164,
+	165, 166, 167, 167, 168, 169, 170, 171, 171, 172, 173,
+	174, 175, 176, 176, 177, 178, 179, 180, 181, 181, 182,
+	183, 184, 185, 186, 187, 187, 188, 189, 190, 191, 192,
+	193, 194, 194, 195, 196, 197, 198, 199, 200, 201, 202,
+	202, 203, 204, 205, 206, 207, 208, 209, 210, 211, 212,
+	212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222,
+	223, 224, 225, 226, 227, 227, 228, 229, 230, 231, 232,
+	233, 234, 235, 236, 237, 238, 239, 240, 241, 242, 243,
+	244, 245, 246, 247, 248, 249, 250, 251, 252, 253, 254,
+	255, 256, 257, 258, 259, 260, 261, 262, 263, 264, 265,
+	266, 267, 268, 269, 271, 272, 273, 274, 275, 276, 277,
+	278, 279, 280, 281, 282, 283, 284, 285, 286, 288, 289,
+	290, 291, 292, 293, 294, 295, 296, 297, 298, 300, 301,
+	302, 303, 304, 305, 306, 307, 308, 310, 311, 312, 313,
+	314, 315, 316, 317, 319, 320, 321, 322, 323, 324, 326,
+	327, 328, 329, 330, 331, 332, 334, 335, 336, 337, 338,
+	339, 341, 342, 343, 344, 345, 347, 348, 349, 350, 351,
+	353, 354, 355, 356, 357, 359, 360, 361, 362, 363, 365,
+	366, 367, 368, 370, 371, 372, 373, 375, 376, 377, 378,
+	380, 381, 382, 383, 385, 386, 387, 388, 390, 391, 392,
+	393, 395, 396, 397, 399, 400, 401, 402, 404, 405, 406,
+	408, 409, 410, 411, 413, 414, 415, 417, 418, 419, 421,
+	422, 423, 425, 426, 427, 429, 430, 431, 433, 434, 435,
+	437, 438, 439, 441, 442, 443, 445, 446, 447, 449, 450,
+	452, 453, 454, 456, 457, 458, 460, 461, 463, 464, 465,
+	467, 468, 469, 471, 472, 474, 475, 477, 478, 479, 481,
+	482, 484, 485, 486, 488, 489, 491, 492, 494, 495, 496,
+	498, 499, 501, 502, 504, 505, 507, 508, 509, 511, 512,
+	514, 515, 517, 518, 520, 521, 523, 524, 526, 527, 529,
+	530, 532, 533, 535, 536, 538, 539, 541, 542, 544, 545,
+	547, 548, 550, 551, 553, 554, 556, 557, 559, 560, 562,
+	563, 565, 566, 568, 569, 571, 573, 574, 576, 577, 579,
+	580, 582, 583, 585, 587, 588, 590, 591, 593, 595, 596,
+	598, 599, 601, 602, 604, 606, 607, 609, 610, 612, 614,
+	615, 617, 618, 620, 622, 623, 625, 627, 628, 630, 631,
+	633, 635, 636, 638, 640, 641, 643, 645, 646, 648, 650,
+	651, 653, 654, 656, 658, 659, 661, 663, 664, 666, 668,
+	670, 671, 673, 675, 676, 678, 680, 681, 683, 685, 686,
+	688, 690, 692, 693, 695, 697, 698, 700, 702, 704, 705,
+	707, 709, 711, 712, 714, 716, 717, 719, 721, 723, 724,
+	726, 728, 730, 732, 733, 735, 737, 739, 740, 742, 744,
+	746, 747, 749, 751, 753, 755, 756, 758, 760, 762, 764,
+	765, 767, 769, 771, 773, 774, 776, 778, 780, 782, 784,
+	785, 787, 789, 791, 793, 795, 796, 798, 800, 802, 804,
+	806, 807, 809, 811, 813, 815, 817, 819, 821, 822, 824,
+	826, 828, 830, 832, 834, 836, 837, 839, 841, 843, 845,
+	847, 849, 851, 853, 855, 856, 858, 860, 862, 864, 866,
+	868, 870, 872, 874, 876, 878, 880, 882, 883, 885, 887,
+	889, 891, 893, 895, 897, 899, 901, 903, 905, 907, 909,
+	911, 913, 915, 917, 919, 921, 923, 925, 927, 929, 931,
+	933, 935, 937, 939, 941, 943, 945, 947, 949, 951, 953,
+	955, 957, 959, 961, 963, 965, 967, 969, 971, 973, 975,
+	977, 979, 981, 984, 986, 988, 990, 992, 994, 996, 998,
+	1000, 1002, 1004, 1006, 1008, 1010, 1013, 1015, 1017, 1019, 1021,
+	1023,
+};
+
+static const u16 xgamma10_22[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 4, 4, 4, 4, 4, 4, 4, 4, 4, 5,
+	5, 5, 5, 5, 5, 5, 5, 5, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9,
+	9, 10, 10, 10, 10, 10, 10, 11, 11, 11, 11,
+	11, 11, 12, 12, 12, 12, 12, 13, 13, 13, 13,
+	13, 14, 14, 14, 14, 15, 15, 15, 15, 15, 16,
+	16, 16, 16, 17, 17, 17, 17, 18, 18, 18, 18,
+	18, 19, 19, 19, 19, 20, 20, 20, 21, 21, 21,
+	21, 22, 22, 22, 22, 23, 23, 23, 23, 24, 24,
+	24, 25, 25, 25, 25, 26, 26, 26, 27, 27, 27,
+	28, 28, 28, 29, 29, 29, 29, 30, 30, 30, 31,
+	31, 31, 32, 32, 32, 33, 33, 33, 34, 34, 34,
+	35, 35, 35, 36, 36, 37, 37, 37, 38, 38, 38,
+	39, 39, 39, 40, 40, 41, 41, 41, 42, 42, 43,
+	43, 43, 44, 44, 44, 45, 45, 46, 46, 46, 47,
+	47, 48, 48, 49, 49, 49, 50, 50, 51, 51, 52,
+	52, 52, 53, 53, 54, 54, 55, 55, 55, 56, 56,
+	57, 57, 58, 58, 59, 59, 60, 60, 61, 61, 61,
+	62, 62, 63, 63, 64, 64, 65, 65, 66, 66, 67,
+	67, 68, 68, 69, 69, 70, 70, 71, 71, 72, 72,
+	73, 73, 74, 75, 75, 76, 76, 77, 77, 78, 78,
+	79, 79, 80, 80, 81, 82, 82, 83, 83, 84, 84,
+	85, 85, 86, 87, 87, 88, 88, 89, 89, 90, 91,
+	91, 92, 92, 93, 94, 94, 95, 95, 96, 97, 97,
+	98, 98, 99, 100, 100, 101, 102, 102, 103, 103, 104,
+	105, 105, 106, 107, 107, 108, 109, 109, 110, 110, 111,
+	112, 112, 113, 114, 114, 115, 116, 116, 117, 118, 118,
+	119, 120, 121, 121, 122, 123, 123, 124, 125, 125, 126,
+	127, 127, 128, 129, 130, 130, 131, 132, 132, 133, 134,
+	135, 135, 136, 137, 138, 138, 139, 140, 141, 141, 142,
+	143, 144, 144, 145, 146, 147, 147, 148, 149, 150, 150,
+	151, 152, 153, 154, 154, 155, 156, 157, 157, 158, 159,
+	160, 161, 161, 162, 163, 164, 165, 166, 166, 167, 168,
+	169, 170, 170, 171, 172, 173, 174, 175, 175, 176, 177,
+	178, 179, 180, 181, 181, 182, 183, 184, 185, 186, 187,
+	187, 188, 189, 190, 191, 192, 193, 194, 194, 195, 196,
+	197, 198, 199, 200, 201, 202, 203, 203, 204, 205, 206,
+	207, 208, 209, 210, 211, 212, 213, 214, 215, 216, 216,
+	217, 218, 219, 220, 221, 222, 223, 224, 225, 226, 227,
+	228, 229, 230, 231, 232, 233, 234, 235, 236, 237, 238,
+	239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249,
+	250, 251, 252, 253, 254, 255, 256, 257, 258, 259, 260,
+	261, 262, 263, 264, 265, 266, 267, 269, 270, 271, 272,
+	273, 274, 275, 276, 277, 278, 279, 280, 281, 283, 284,
+	285, 286, 287, 288, 289, 290, 291, 292, 294, 295, 296,
+	297, 298, 299, 300, 301, 303, 304, 305, 306, 307, 308,
+	309, 311, 312, 313, 314, 315, 316, 317, 319, 320, 321,
+	322, 323, 324, 326, 327, 328, 329, 330, 332, 333, 334,
+	335, 336, 338, 339, 340, 341, 342, 344, 345, 346, 347,
+	348, 350, 351, 352, 353, 355, 356, 357, 358, 360, 361,
+	362, 363, 365, 366, 367, 368, 370, 371, 372, 373, 375,
+	376, 377, 378, 380, 381, 382, 384, 385, 386, 387, 389,
+	390, 391, 393, 394, 395, 397, 398, 399, 401, 402, 403,
+	405, 406, 407, 409, 410, 411, 413, 414, 415, 417, 418,
+	419, 421, 422, 423, 425, 426, 427, 429, 430, 432, 433,
+	434, 436, 437, 438, 440, 441, 443, 444, 445, 447, 448,
+	450, 451, 452, 454, 455, 457, 458, 459, 461, 462, 464,
+	465, 467, 468, 469, 471, 472, 474, 475, 477, 478, 480,
+	481, 483, 484, 485, 487, 488, 490, 491, 493, 494, 496,
+	497, 499, 500, 502, 503, 505, 506, 508, 509, 511, 512,
+	514, 515, 517, 518, 520, 521, 523, 524, 526, 527, 529,
+	530, 532, 534, 535, 537, 538, 540, 541, 543, 544, 546,
+	548, 549, 551, 552, 554, 555, 557, 559, 560, 562, 563,
+	565, 567, 568, 570, 571, 573, 575, 576, 578, 579, 581,
+	583, 584, 586, 587, 589, 591, 592, 594, 596, 597, 599,
+	601, 602, 604, 605, 607, 609, 610, 612, 614, 615, 617,
+	619, 620, 622, 624, 625, 627, 629, 631, 632, 634, 636,
+	637, 639, 641, 642, 644, 646, 648, 649, 651, 653, 654,
+	656, 658, 660, 661, 663, 665, 667, 668, 670, 672, 674,
+	675, 677, 679, 681, 682, 684, 686, 688, 689, 691, 693,
+	695, 697, 698, 700, 702, 704, 705, 707, 709, 711, 713,
+	714, 716, 718, 720, 722, 724, 725, 727, 729, 731, 733,
+	735, 736, 738, 740, 742, 744, 746, 747, 749, 751, 753,
+	755, 757, 759, 760, 762, 764, 766, 768, 770, 772, 774,
+	776, 777, 779, 781, 783, 785, 787, 789, 791, 793, 795,
+	796, 798, 800, 802, 804, 806, 808, 810, 812, 814, 816,
+	818, 820, 822, 824, 826, 828, 829, 831, 833, 835, 837,
+	839, 841, 843, 845, 847, 849, 851, 853, 855, 857, 859,
+	861, 863, 865, 867, 869, 871, 873, 875, 877, 879, 881,
+	883, 885, 887, 889, 892, 894, 896, 898, 900, 902, 904,
+	906, 908, 910, 912, 914, 916, 918, 920, 922, 925, 927,
+	929, 931, 933, 935, 937, 939, 941, 943, 945, 948, 950,
+	952, 954, 956, 958, 960, 962, 965, 967, 969, 971, 973,
+	975, 977, 980, 982, 984, 986, 988, 990, 992, 995, 997,
+	999, 1001, 1003, 1005, 1008, 1010, 1012, 1014, 1016, 1019, 1021,
+	1023,
+};
+
+static const u16 xgamma10_23[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 5, 5,
+	5, 5, 5, 5, 5, 5, 5, 6, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 8, 9, 9, 9, 9,
+	9, 9, 10, 10, 10, 10, 10, 10, 11, 11, 11,
+	11, 11, 11, 12, 12, 12, 12, 12, 13, 13, 13,
+	13, 13, 14, 14, 14, 14, 14, 15, 15, 15, 15,
+	15, 16, 16, 16, 16, 16, 17, 17, 17, 17, 18,
+	18, 18, 18, 19, 19, 19, 19, 20, 20, 20, 20,
+	21, 21, 21, 21, 22, 22, 22, 22, 23, 23, 23,
+	23, 24, 24, 24, 25, 25, 25, 25, 26, 26, 26,
+	27, 27, 27, 27, 28, 28, 28, 29, 29, 29, 30,
+	30, 30, 30, 31, 31, 31, 32, 32, 32, 33, 33,
+	33, 34, 34, 34, 35, 35, 35, 36, 36, 36, 37,
+	37, 38, 38, 38, 39, 39, 39, 40, 40, 40, 41,
+	41, 42, 42, 42, 43, 43, 43, 44, 44, 45, 45,
+	45, 46, 46, 47, 47, 47, 48, 48, 49, 49, 49,
+	50, 50, 51, 51, 52, 52, 52, 53, 53, 54, 54,
+	55, 55, 55, 56, 56, 57, 57, 58, 58, 59, 59,
+	59, 60, 60, 61, 61, 62, 62, 63, 63, 64, 64,
+	65, 65, 66, 66, 67, 67, 68, 68, 69, 69, 70,
+	70, 71, 71, 72, 72, 73, 73, 74, 74, 75, 75,
+	76, 76, 77, 77, 78, 78, 79, 80, 80, 81, 81,
+	82, 82, 83, 83, 84, 85, 85, 86, 86, 87, 87,
+	88, 89, 89, 90, 90, 91, 91, 92, 93, 93, 94,
+	94, 95, 96, 96, 97, 97, 98, 99, 99, 100, 100,
+	101, 102, 102, 103, 104, 104, 105, 106, 106, 107, 107,
+	108, 109, 109, 110, 111, 111, 112, 113, 113, 114, 115,
+	115, 116, 117, 117, 118, 119, 119, 120, 121, 121, 122,
+	123, 124, 124, 125, 126, 126, 127, 128, 128, 129, 130,
+	131, 131, 132, 133, 133, 134, 135, 136, 136, 137, 138,
+	139, 139, 140, 141, 142, 142, 143, 144, 145, 145, 146,
+	147, 148, 148, 149, 150, 151, 152, 152, 153, 154, 155,
+	156, 156, 157, 158, 159, 160, 160, 161, 162, 163, 164,
+	164, 165, 166, 167, 168, 168, 169, 170, 171, 172, 173,
+	174, 174, 175, 176, 177, 178, 179, 179, 180, 181, 182,
+	183, 184, 185, 186, 186, 187, 188, 189, 190, 191, 192,
+	193, 194, 194, 195, 196, 197, 198, 199, 200, 201, 202,
+	203, 204, 204, 205, 206, 207, 208, 209, 210, 211, 212,
+	213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 222,
+	223, 224, 225, 226, 227, 228, 229, 230, 231, 232, 233,
+	234, 235, 236, 237, 238, 239, 240, 241, 242, 243, 244,
+	245, 246, 248, 249, 250, 251, 252, 253, 254, 255, 256,
+	257, 258, 259, 260, 261, 262, 263, 264, 265, 266, 268,
+	269, 270, 271, 272, 273, 274, 275, 276, 277, 278, 280,
+	281, 282, 283, 284, 285, 286, 287, 288, 290, 291, 292,
+	293, 294, 295, 296, 298, 299, 300, 301, 302, 303, 304,
+	306, 307, 308, 309, 310, 311, 313, 314, 315, 316, 317,
+	319, 320, 321, 322, 323, 325, 326, 327, 328, 329, 331,
+	332, 333, 334, 335, 337, 338, 339, 340, 342, 343, 344,
+	345, 347, 348, 349, 350, 352, 353, 354, 355, 357, 358,
+	359, 360, 362, 363, 364, 366, 367, 368, 369, 371, 372,
+	373, 375, 376, 377, 379, 380, 381, 383, 384, 385, 386,
+	388, 389, 390, 392, 393, 394, 396, 397, 399, 400, 401,
+	403, 404, 405, 407, 408, 409, 411, 412, 414, 415, 416,
+	418, 419, 420, 422, 423, 425, 426, 427, 429, 430, 432,
+	433, 435, 436, 437, 439, 440, 442, 443, 444, 446, 447,
+	449, 450, 452, 453, 455, 456, 458, 459, 460, 462, 463,
+	465, 466, 468, 469, 471, 472, 474, 475, 477, 478, 480,
+	481, 483, 484, 486, 487, 489, 490, 492, 493, 495, 496,
+	498, 499, 501, 502, 504, 506, 507, 509, 510, 512, 513,
+	515, 516, 518, 520, 521, 523, 524, 526, 527, 529, 531,
+	532, 534, 535, 537, 539, 540, 542, 543, 545, 547, 548,
+	550, 551, 553, 555, 556, 558, 560, 561, 563, 565, 566,
+	568, 569, 571, 573, 574, 576, 578, 579, 581, 583, 584,
+	586, 588, 590, 591, 593, 595, 596, 598, 600, 601, 603,
+	605, 606, 608, 610, 612, 613, 615, 617, 619, 620, 622,
+	624, 625, 627, 629, 631, 632, 634, 636, 638, 640, 641,
+	643, 645, 647, 648, 650, 652, 654, 655, 657, 659, 661,
+	663, 664, 666, 668, 670, 672, 674, 675, 677, 679, 681,
+	683, 684, 686, 688, 690, 692, 694, 696, 697, 699, 701,
+	703, 705, 707, 709, 710, 712, 714, 716, 718, 720, 722,
+	724, 725, 727, 729, 731, 733, 735, 737, 739, 741, 743,
+	745, 746, 748, 750, 752, 754, 756, 758, 760, 762, 764,
+	766, 768, 770, 772, 774, 776, 778, 780, 782, 784, 786,
+	787, 789, 791, 793, 795, 797, 799, 801, 803, 805, 807,
+	809, 811, 814, 816, 818, 820, 822, 824, 826, 828, 830,
+	832, 834, 836, 838, 840, 842, 844, 846, 848, 850, 852,
+	854, 857, 859, 861, 863, 865, 867, 869, 871, 873, 875,
+	878, 880, 882, 884, 886, 888, 890, 892, 894, 897, 899,
+	901, 903, 905, 907, 909, 912, 914, 916, 918, 920, 922,
+	925, 927, 929, 931, 933, 936, 938, 940, 942, 944, 946,
+	949, 951, 953, 955, 958, 960, 962, 964, 966, 969, 971,
+	973, 975, 978, 980, 982, 984, 987, 989, 991, 993, 996,
+	998, 1000, 1002, 1005, 1007, 1009, 1012, 1014, 1016, 1018, 1021,
+	1023,
+};
+
+static const u16 xgamma10_24[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 5, 5, 5,
+	5, 5, 5, 5, 5, 5, 6, 6, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 8, 8, 9, 9, 9,
+	9, 9, 9, 10, 10, 10, 10, 10, 10, 11, 11,
+	11, 11, 11, 11, 12, 12, 12, 12, 12, 12, 13,
+	13, 13, 13, 13, 14, 14, 14, 14, 14, 15, 15,
+	15, 15, 15, 16, 16, 16, 16, 16, 17, 17, 17,
+	17, 18, 18, 18, 18, 18, 19, 19, 19, 19, 20,
+	20, 20, 20, 21, 21, 21, 21, 22, 22, 22, 22,
+	23, 23, 23, 23, 24, 24, 24, 24, 25, 25, 25,
+	26, 26, 26, 26, 27, 27, 27, 28, 28, 28, 28,
+	29, 29, 29, 30, 30, 30, 31, 31, 31, 32, 32,
+	32, 32, 33, 33, 33, 34, 34, 34, 35, 35, 35,
+	36, 36, 36, 37, 37, 38, 38, 38, 39, 39, 39,
+	40, 40, 40, 41, 41, 41, 42, 42, 43, 43, 43,
+	44, 44, 44, 45, 45, 46, 46, 46, 47, 47, 48,
+	48, 48, 49, 49, 50, 50, 50, 51, 51, 52, 52,
+	53, 53, 53, 54, 54, 55, 55, 56, 56, 56, 57,
+	57, 58, 58, 59, 59, 60, 60, 61, 61, 61, 62,
+	62, 63, 63, 64, 64, 65, 65, 66, 66, 67, 67,
+	68, 68, 69, 69, 70, 70, 71, 71, 72, 72, 73,
+	73, 74, 74, 75, 75, 76, 76, 77, 77, 78, 79,
+	79, 80, 80, 81, 81, 82, 82, 83, 83, 84, 85,
+	85, 86, 86, 87, 87, 88, 89, 89, 90, 90, 91,
+	91, 92, 93, 93, 94, 94, 95, 96, 96, 97, 97,
+	98, 99, 99, 100, 100, 101, 102, 102, 103, 104, 104,
+	105, 106, 106, 107, 107, 108, 109, 109, 110, 111, 111,
+	112, 113, 113, 114, 115, 115, 116, 117, 117, 118, 119,
+	119, 120, 121, 121, 122, 123, 124, 124, 125, 126, 126,
+	127, 128, 129, 129, 130, 131, 131, 132, 133, 134, 134,
+	135, 136, 137, 137, 138, 139, 140, 140, 141, 142, 143,
+	143, 144, 145, 146, 146, 147, 148, 149, 149, 150, 151,
+	152, 153, 153, 154, 155, 156, 157, 157, 158, 159, 160,
+	161, 161, 162, 163, 164, 165, 166, 166, 167, 168, 169,
+	170, 171, 171, 172, 173, 174, 175, 176, 177, 177, 178,
+	179, 180, 181, 182, 183, 184, 184, 185, 186, 187, 188,
+	189, 190, 191, 192, 192, 193, 194, 195, 196, 197, 198,
+	199, 200, 201, 202, 203, 204, 204, 205, 206, 207, 208,
+	209, 210, 211, 212, 213, 214, 215, 216, 217, 218, 219,
+	220, 221, 222, 223, 224, 225, 226, 227, 228, 229, 230,
+	231, 232, 233, 234, 235, 236, 237, 238, 239, 240, 241,
+	242, 243, 244, 245, 246, 247, 248, 249, 250, 251, 252,
+	253, 255, 256, 257, 258, 259, 260, 261, 262, 263, 264,
+	265, 266, 268, 269, 270, 271, 272, 273, 274, 275, 276,
+	277, 279, 280, 281, 282, 283, 284, 285, 287, 288, 289,
+	290, 291, 292, 293, 295, 296, 297, 298, 299, 300, 302,
+	303, 304, 305, 306, 308, 309, 310, 311, 312, 314, 315,
+	316, 317, 318, 320, 321, 322, 323, 324, 326, 327, 328,
+	329, 331, 332, 333, 334, 336, 337, 338, 339, 341, 342,
+	343, 344, 346, 347, 348, 350, 351, 352, 353, 355, 356,
+	357, 359, 360, 361, 363, 364, 365, 367, 368, 369, 370,
+	372, 373, 374, 376, 377, 378, 380, 381, 383, 384, 385,
+	387, 388, 389, 391, 392, 393, 395, 396, 398, 399, 400,
+	402, 403, 405, 406, 407, 409, 410, 412, 413, 414, 416,
+	417, 419, 420, 421, 423, 424, 426, 427, 429, 430, 432,
+	433, 434, 436, 437, 439, 440, 442, 443, 445, 446, 448,
+	449, 451, 452, 454, 455, 457, 458, 460, 461, 463, 464,
+	466, 467, 469, 470, 472, 473, 475, 476, 478, 479, 481,
+	483, 484, 486, 487, 489, 490, 492, 493, 495, 497, 498,
+	500, 501, 503, 505, 506, 508, 509, 511, 512, 514, 516,
+	517, 519, 521, 522, 524, 525, 527, 529, 530, 532, 534,
+	535, 537, 539, 540, 542, 543, 545, 547, 548, 550, 552,
+	553, 555, 557, 559, 560, 562, 564, 565, 567, 569, 570,
+	572, 574, 576, 577, 579, 581, 582, 584, 586, 588, 589,
+	591, 593, 595, 596, 598, 600, 602, 603, 605, 607, 609,
+	610, 612, 614, 616, 618, 619, 621, 623, 625, 627, 628,
+	630, 632, 634, 636, 637, 639, 641, 643, 645, 647, 648,
+	650, 652, 654, 656, 658, 660, 661, 663, 665, 667, 669,
+	671, 673, 674, 676, 678, 680, 682, 684, 686, 688, 690,
+	692, 693, 695, 697, 699, 701, 703, 705, 707, 709, 711,
+	713, 715, 717, 719, 721, 723, 724, 726, 728, 730, 732,
+	734, 736, 738, 740, 742, 744, 746, 748, 750, 752, 754,
+	756, 758, 760, 762, 764, 766, 768, 770, 772, 774, 777,
+	779, 781, 783, 785, 787, 789, 791, 793, 795, 797, 799,
+	801, 803, 805, 808, 810, 812, 814, 816, 818, 820, 822,
+	824, 826, 829, 831, 833, 835, 837, 839, 841, 844, 846,
+	848, 850, 852, 854, 856, 859, 861, 863, 865, 867, 870,
+	872, 874, 876, 878, 880, 883, 885, 887, 889, 891, 894,
+	896, 898, 900, 903, 905, 907, 909, 912, 914, 916, 918,
+	921, 923, 925, 927, 930, 932, 934, 936, 939, 941, 943,
+	946, 948, 950, 952, 955, 957, 959, 962, 964, 966, 969,
+	971, 973, 976, 978, 980, 983, 985, 987, 990, 992, 994,
+	997, 999, 1002, 1004, 1006, 1009, 1011, 1013, 1016, 1018, 1021,
+	1023,
+};
+
+static const u16 xgamma10_25[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 5, 6, 6, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 9, 9, 9,
+	9, 9, 9, 9, 10, 10, 10, 10, 10, 10, 11,
+	11, 11, 11, 11, 11, 12, 12, 12, 12, 12, 12,
+	13, 13, 13, 13, 13, 13, 14, 14, 14, 14, 14,
+	15, 15, 15, 15, 15, 16, 16, 16, 16, 16, 17,
+	17, 17, 17, 18, 18, 18, 18, 18, 19, 19, 19,
+	19, 20, 20, 20, 20, 20, 21, 21, 21, 21, 22,
+	22, 22, 22, 23, 23, 23, 23, 24, 24, 24, 25,
+	25, 25, 25, 26, 26, 26, 26, 27, 27, 27, 28,
+	28, 28, 28, 29, 29, 29, 30, 30, 30, 31, 31,
+	31, 31, 32, 32, 32, 33, 33, 33, 34, 34, 34,
+	35, 35, 35, 36, 36, 36, 37, 37, 37, 38, 38,
+	38, 39, 39, 39, 40, 40, 40, 41, 41, 42, 42,
+	42, 43, 43, 43, 44, 44, 45, 45, 45, 46, 46,
+	46, 47, 47, 48, 48, 48, 49, 49, 50, 50, 50,
+	51, 51, 52, 52, 53, 53, 53, 54, 54, 55, 55,
+	56, 56, 56, 57, 57, 58, 58, 59, 59, 60, 60,
+	60, 61, 61, 62, 62, 63, 63, 64, 64, 65, 65,
+	66, 66, 67, 67, 68, 68, 69, 69, 70, 70, 71,
+	71, 72, 72, 73, 73, 74, 74, 75, 75, 76, 76,
+	77, 77, 78, 78, 79, 79, 80, 80, 81, 82, 82,
+	83, 83, 84, 84, 85, 85, 86, 87, 87, 88, 88,
+	89, 89, 90, 91, 91, 92, 92, 93, 94, 94, 95,
+	95, 96, 97, 97, 98, 98, 99, 100, 100, 101, 102,
+	102, 103, 103, 104, 105, 105, 106, 107, 107, 108, 109,
+	109, 110, 110, 111, 112, 112, 113, 114, 114, 115, 116,
+	117, 117, 118, 119, 119, 120, 121, 121, 122, 123, 123,
+	124, 125, 126, 126, 127, 128, 128, 129, 130, 131, 131,
+	132, 133, 133, 134, 135, 136, 136, 137, 138, 139, 139,
+	140, 141, 142, 143, 143, 144, 145, 146, 146, 147, 148,
+	149, 149, 150, 151, 152, 153, 153, 154, 155, 156, 157,
+	158, 158, 159, 160, 161, 162, 162, 163, 164, 165, 166,
+	167, 167, 168, 169, 170, 171, 172, 173, 173, 174, 175,
+	176, 177, 178, 179, 180, 180, 181, 182, 183, 184, 185,
+	186, 187, 188, 188, 189, 190, 191, 192, 193, 194, 195,
+	196, 197, 198, 199, 200, 200, 201, 202, 203, 204, 205,
+	206, 207, 208, 209, 210, 211, 212, 213, 214, 215, 216,
+	217, 218, 219, 220, 221, 222, 223, 224, 225, 226, 227,
+	228, 229, 230, 231, 232, 233, 234, 235, 236, 237, 238,
+	239, 240, 241, 242, 243, 244, 245, 247, 248, 249, 250,
+	251, 252, 253, 254, 255, 256, 257, 258, 260, 261, 262,
+	263, 264, 265, 266, 267, 268, 270, 271, 272, 273, 274,
+	275, 276, 277, 279, 280, 281, 282, 283, 284, 286, 287,
+	288, 289, 290, 291, 293, 294, 295, 296, 297, 298, 300,
+	301, 302, 303, 304, 306, 307, 308, 309, 311, 312, 313,
+	314, 315, 317, 318, 319, 320, 322, 323, 324, 325, 327,
+	328, 329, 330, 332, 333, 334, 336, 337, 338, 339, 341,
+	342, 343, 345, 346, 347, 349, 350, 351, 352, 354, 355,
+	356, 358, 359, 360, 362, 363, 364, 366, 367, 369, 370,
+	371, 373, 374, 375, 377, 378, 379, 381, 382, 384, 385,
+	386, 388, 389, 391, 392, 393, 395, 396, 398, 399, 400,
+	402, 403, 405, 406, 408, 409, 411, 412, 413, 415, 416,
+	418, 419, 421, 422, 424, 425, 427, 428, 430, 431, 433,
+	434, 436, 437, 439, 440, 442, 443, 445, 446, 448, 449,
+	451, 452, 454, 455, 457, 458, 460, 461, 463, 465, 466,
+	468, 469, 471, 472, 474, 476, 477, 479, 480, 482, 483,
+	485, 487, 488, 490, 491, 493, 495, 496, 498, 500, 501,
+	503, 504, 506, 508, 509, 511, 513, 514, 516, 518, 519,
+	521, 523, 524, 526, 528, 529, 531, 533, 534, 536, 538,
+	540, 541, 543, 545, 546, 548, 550, 552, 553, 555, 557,
+	558, 560, 562, 564, 565, 567, 569, 571, 572, 574, 576,
+	578, 580, 581, 583, 585, 587, 588, 590, 592, 594, 596,
+	597, 599, 601, 603, 605, 607, 608, 610, 612, 614, 616,
+	618, 619, 621, 623, 625, 627, 629, 631, 632, 634, 636,
+	638, 640, 642, 644, 646, 648, 649, 651, 653, 655, 657,
+	659, 661, 663, 665, 667, 669, 671, 673, 674, 676, 678,
+	680, 682, 684, 686, 688, 690, 692, 694, 696, 698, 700,
+	702, 704, 706, 708, 710, 712, 714, 716, 718, 720, 722,
+	724, 726, 728, 730, 732, 734, 736, 739, 741, 743, 745,
+	747, 749, 751, 753, 755, 757, 759, 761, 763, 766, 768,
+	770, 772, 774, 776, 778, 780, 782, 785, 787, 789, 791,
+	793, 795, 797, 800, 802, 804, 806, 808, 810, 813, 815,
+	817, 819, 821, 824, 826, 828, 830, 832, 835, 837, 839,
+	841, 843, 846, 848, 850, 852, 855, 857, 859, 861, 864,
+	866, 868, 870, 873, 875, 877, 880, 882, 884, 886, 889,
+	891, 893, 896, 898, 900, 903, 905, 907, 910, 912, 914,
+	917, 919, 921, 924, 926, 928, 931, 933, 935, 938, 940,
+	942, 945, 947, 950, 952, 954, 957, 959, 962, 964, 966,
+	969, 971, 974, 976, 979, 981, 983, 986, 988, 991, 993,
+	996, 998, 1001, 1003, 1006, 1008, 1011, 1013, 1016, 1018, 1021,
+	1023,
+};
+
+static const u16 xgamma10_26[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 5, 6, 6, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 9, 9,
+	9, 9, 9, 9, 9, 10, 10, 10, 10, 10, 10,
+	11, 11, 11, 11, 11, 11, 11, 12, 12, 12, 12,
+	12, 13, 13, 13, 13, 13, 13, 14, 14, 14, 14,
+	14, 14, 15, 15, 15, 15, 15, 16, 16, 16, 16,
+	16, 17, 17, 17, 17, 18, 18, 18, 18, 18, 19,
+	19, 19, 19, 19, 20, 20, 20, 20, 21, 21, 21,
+	21, 22, 22, 22, 22, 23, 23, 23, 23, 24, 24,
+	24, 24, 25, 25, 25, 25, 26, 26, 26, 27, 27,
+	27, 27, 28, 28, 28, 28, 29, 29, 29, 30, 30,
+	30, 31, 31, 31, 31, 32, 32, 32, 33, 33, 33,
+	34, 34, 34, 35, 35, 35, 36, 36, 36, 37, 37,
+	37, 38, 38, 38, 39, 39, 39, 40, 40, 40, 41,
+	41, 41, 42, 42, 43, 43, 43, 44, 44, 44, 45,
+	45, 46, 46, 46, 47, 47, 47, 48, 48, 49, 49,
+	49, 50, 50, 51, 51, 51, 52, 52, 53, 53, 54,
+	54, 54, 55, 55, 56, 56, 57, 57, 57, 58, 58,
+	59, 59, 60, 60, 61, 61, 62, 62, 62, 63, 63,
+	64, 64, 65, 65, 66, 66, 67, 67, 68, 68, 69,
+	69, 70, 70, 71, 71, 72, 72, 73, 73, 74, 74,
+	75, 75, 76, 76, 77, 77, 78, 78, 79, 80, 80,
+	81, 81, 82, 82, 83, 83, 84, 84, 85, 86, 86,
+	87, 87, 88, 88, 89, 90, 90, 91, 91, 92, 93,
+	93, 94, 94, 95, 96, 96, 97, 97, 98, 99, 99,
+	100, 100, 101, 102, 102, 103, 104, 104, 105, 106, 106,
+	107, 107, 108, 109, 109, 110, 111, 111, 112, 113, 113,
+	114, 115, 115, 116, 117, 117, 118, 119, 120, 120, 121,
+	122, 122, 123, 124, 124, 125, 126, 127, 127, 128, 129,
+	129, 130, 131, 132, 132, 133, 134, 135, 135, 136, 137,
+	138, 138, 139, 140, 141, 141, 142, 143, 144, 145, 145,
+	146, 147, 148, 149, 149, 150, 151, 152, 153, 153, 154,
+	155, 156, 157, 157, 158, 159, 160, 161, 162, 162, 163,
+	164, 165, 166, 167, 167, 168, 169, 170, 171, 172, 173,
+	173, 174, 175, 176, 177, 178, 179, 180, 181, 181, 182,
+	183, 184, 185, 186, 187, 188, 189, 190, 191, 191, 192,
+	193, 194, 195, 196, 197, 198, 199, 200, 201, 202, 203,
+	204, 205, 206, 207, 208, 209, 210, 211, 212, 213, 214,
+	215, 216, 217, 218, 219, 220, 221, 222, 223, 224, 225,
+	226, 227, 228, 229, 230, 231, 232, 233, 234, 235, 236,
+	237, 238, 239, 240, 241, 242, 243, 245, 246, 247, 248,
+	249, 250, 251, 252, 253, 254, 256, 257, 258, 259, 260,
+	261, 262, 263, 264, 266, 267, 268, 269, 270, 271, 272,
+	274, 275, 276, 277, 278, 279, 281, 282, 283, 284, 285,
+	286, 288, 289, 290, 291, 292, 294, 295, 296, 297, 299,
+	300, 301, 302, 303, 305, 306, 307, 308, 310, 311, 312,
+	313, 315, 316, 317, 318, 320, 321, 322, 323, 325, 326,
+	327, 329, 330, 331, 333, 334, 335, 336, 338, 339, 340,
+	342, 343, 344, 346, 347, 348, 350, 351, 352, 354, 355,
+	356, 358, 359, 361, 362, 363, 365, 366, 367, 369, 370,
+	372, 373, 374, 376, 377, 379, 380, 381, 383, 384, 386,
+	387, 389, 390, 391, 393, 394, 396, 397, 399, 400, 402,
+	403, 405, 406, 407, 409, 410, 412, 413, 415, 416, 418,
+	419, 421, 422, 424, 425, 427, 428, 430, 432, 433, 435,
+	436, 438, 439, 441, 442, 444, 445, 447, 449, 450, 452,
+	453, 455, 456, 458, 460, 461, 463, 464, 466, 468, 469,
+	471, 472, 474, 476, 477, 479, 481, 482, 484, 485, 487,
+	489, 490, 492, 494, 495, 497, 499, 500, 502, 504, 505,
+	507, 509, 510, 512, 514, 516, 517, 519, 521, 522, 524,
+	526, 528, 529, 531, 533, 535, 536, 538, 540, 542, 543,
+	545, 547, 549, 550, 552, 554, 556, 558, 559, 561, 563,
+	565, 567, 568, 570, 572, 574, 576, 577, 579, 581, 583,
+	585, 587, 588, 590, 592, 594, 596, 598, 600, 601, 603,
+	605, 607, 609, 611, 613, 615, 617, 619, 620, 622, 624,
+	626, 628, 630, 632, 634, 636, 638, 640, 642, 644, 646,
+	648, 650, 651, 653, 655, 657, 659, 661, 663, 665, 667,
+	669, 671, 673, 675, 677, 679, 681, 683, 685, 688, 690,
+	692, 694, 696, 698, 700, 702, 704, 706, 708, 710, 712,
+	714, 716, 718, 721, 723, 725, 727, 729, 731, 733, 735,
+	737, 740, 742, 744, 746, 748, 750, 752, 755, 757, 759,
+	761, 763, 765, 768, 770, 772, 774, 776, 779, 781, 783,
+	785, 787, 790, 792, 794, 796, 798, 801, 803, 805, 807,
+	810, 812, 814, 816, 819, 821, 823, 826, 828, 830, 832,
+	835, 837, 839, 842, 844, 846, 849, 851, 853, 855, 858,
+	860, 862, 865, 867, 870, 872, 874, 877, 879, 881, 884,
+	886, 888, 891, 893, 896, 898, 900, 903, 905, 908, 910,
+	913, 915, 917, 920, 922, 925, 927, 930, 932, 934, 937,
+	939, 942, 944, 947, 949, 952, 954, 957, 959, 962, 964,
+	967, 969, 972, 974, 977, 979, 982, 984, 987, 990, 992,
+	995, 997, 1000, 1002, 1005, 1007, 1010, 1013, 1015, 1018, 1020,
+	1023,
+};
+
+static const u16 xgamma10_27[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 9, 9,
+	9, 9, 9, 9, 9, 10, 10, 10, 10, 10, 10,
+	10, 11, 11, 11, 11, 11, 11, 11, 12, 12, 12,
+	12, 12, 12, 13, 13, 13, 13, 13, 14, 14, 14,
+	14, 14, 14, 15, 15, 15, 15, 15, 16, 16, 16,
+	16, 16, 17, 17, 17, 17, 17, 18, 18, 18, 18,
+	18, 19, 19, 19, 19, 20, 20, 20, 20, 20, 21,
+	21, 21, 21, 22, 22, 22, 22, 23, 23, 23, 23,
+	24, 24, 24, 24, 25, 25, 25, 25, 26, 26, 26,
+	26, 27, 27, 27, 27, 28, 28, 28, 29, 29, 29,
+	29, 30, 30, 30, 31, 31, 31, 32, 32, 32, 32,
+	33, 33, 33, 34, 34, 34, 35, 35, 35, 36, 36,
+	36, 37, 37, 37, 38, 38, 38, 39, 39, 39, 40,
+	40, 40, 41, 41, 41, 42, 42, 43, 43, 43, 44,
+	44, 44, 45, 45, 46, 46, 46, 47, 47, 47, 48,
+	48, 49, 49, 49, 50, 50, 51, 51, 51, 52, 52,
+	53, 53, 54, 54, 54, 55, 55, 56, 56, 57, 57,
+	57, 58, 58, 59, 59, 60, 60, 61, 61, 61, 62,
+	62, 63, 63, 64, 64, 65, 65, 66, 66, 67, 67,
+	68, 68, 69, 69, 70, 70, 71, 71, 72, 72, 73,
+	73, 74, 74, 75, 75, 76, 76, 77, 77, 78, 78,
+	79, 79, 80, 81, 81, 82, 82, 83, 83, 84, 84,
+	85, 86, 86, 87, 87, 88, 88, 89, 90, 90, 91,
+	91, 92, 92, 93, 94, 94, 95, 95, 96, 97, 97,
+	98, 99, 99, 100, 100, 101, 102, 102, 103, 104, 104,
+	105, 105, 106, 107, 107, 108, 109, 109, 110, 111, 111,
+	112, 113, 113, 114, 115, 115, 116, 117, 118, 118, 119,
+	120, 120, 121, 122, 122, 123, 124, 125, 125, 126, 127,
+	127, 128, 129, 130, 130, 131, 132, 133, 133, 134, 135,
+	136, 136, 137, 138, 139, 139, 140, 141, 142, 143, 143,
+	144, 145, 146, 146, 147, 148, 149, 150, 150, 151, 152,
+	153, 154, 155, 155, 156, 157, 158, 159, 160, 160, 161,
+	162, 163, 164, 165, 165, 166, 167, 168, 169, 170, 171,
+	172, 172, 173, 174, 175, 176, 177, 178, 179, 180, 180,
+	181, 182, 183, 184, 185, 186, 187, 188, 189, 190, 191,
+	192, 192, 193, 194, 195, 196, 197, 198, 199, 200, 201,
+	202, 203, 204, 205, 206, 207, 208, 209, 210, 211, 212,
+	213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 223,
+	224, 225, 226, 227, 228, 229, 230, 231, 233, 234, 235,
+	236, 237, 238, 239, 240, 241, 242, 243, 244, 246, 247,
+	248, 249, 250, 251, 252, 253, 254, 256, 257, 258, 259,
+	260, 261, 262, 263, 265, 266, 267, 268, 269, 270, 272,
+	273, 274, 275, 276, 278, 279, 280, 281, 282, 283, 285,
+	286, 287, 288, 290, 291, 292, 293, 294, 296, 297, 298,
+	299, 301, 302, 303, 304, 306, 307, 308, 309, 311, 312,
+	313, 315, 316, 317, 318, 320, 321, 322, 324, 325, 326,
+	328, 329, 330, 332, 333, 334, 336, 337, 338, 340, 341,
+	342, 344, 345, 346, 348, 349, 351, 352, 353, 355, 356,
+	357, 359, 360, 362, 363, 364, 366, 367, 369, 370, 372,
+	373, 374, 376, 377, 379, 380, 382, 383, 385, 386, 387,
+	389, 390, 392, 393, 395, 396, 398, 399, 401, 402, 404,
+	405, 407, 408, 410, 411, 413, 414, 416, 417, 419, 421,
+	422, 424, 425, 427, 428, 430, 431, 433, 435, 436, 438,
+	439, 441, 442, 444, 446, 447, 449, 450, 452, 454, 455,
+	457, 459, 460, 462, 463, 465, 467, 468, 470, 472, 473,
+	475, 477, 478, 480, 482, 483, 485, 487, 488, 490, 492,
+	494, 495, 497, 499, 500, 502, 504, 506, 507, 509, 511,
+	513, 514, 516, 518, 520, 521, 523, 525, 527, 528, 530,
+	532, 534, 536, 537, 539, 541, 543, 545, 546, 548, 550,
+	552, 554, 556, 557, 559, 561, 563, 565, 567, 569, 570,
+	572, 574, 576, 578, 580, 582, 584, 586, 587, 589, 591,
+	593, 595, 597, 599, 601, 603, 605, 607, 609, 611, 613,
+	614, 616, 618, 620, 622, 624, 626, 628, 630, 632, 634,
+	636, 638, 640, 642, 644, 646, 648, 650, 652, 654, 656,
+	659, 661, 663, 665, 667, 669, 671, 673, 675, 677, 679,
+	681, 683, 685, 688, 690, 692, 694, 696, 698, 700, 702,
+	705, 707, 709, 711, 713, 715, 717, 720, 722, 724, 726,
+	728, 730, 733, 735, 737, 739, 741, 744, 746, 748, 750,
+	752, 755, 757, 759, 761, 764, 766, 768, 770, 773, 775,
+	777, 779, 782, 784, 786, 789, 791, 793, 795, 798, 800,
+	802, 805, 807, 809, 812, 814, 816, 819, 821, 823, 826,
+	828, 831, 833, 835, 838, 840, 842, 845, 847, 850, 852,
+	854, 857, 859, 862, 864, 867, 869, 871, 874, 876, 879,
+	881, 884, 886, 889, 891, 894, 896, 899, 901, 903, 906,
+	908, 911, 914, 916, 919, 921, 924, 926, 929, 931, 934,
+	936, 939, 941, 944, 947, 949, 952, 954, 957, 959, 962,
+	965, 967, 970, 973, 975, 978, 980, 983, 986, 988, 991,
+	994, 996, 999, 1002, 1004, 1007, 1010, 1012, 1015, 1018, 1020,
+	1023,
+};
+
+static const u16 xgamma10_28[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 9, 9,
+	9, 9, 9, 9, 9, 9, 10, 10, 10, 10, 10,
+	10, 10, 11, 11, 11, 11, 11, 11, 12, 12, 12,
+	12, 12, 12, 12, 13, 13, 13, 13, 13, 13, 14,
+	14, 14, 14, 14, 15, 15, 15, 15, 15, 15, 16,
+	16, 16, 16, 16, 17, 17, 17, 17, 17, 18, 18,
+	18, 18, 18, 19, 19, 19, 19, 20, 20, 20, 20,
+	20, 21, 21, 21, 21, 22, 22, 22, 22, 23, 23,
+	23, 23, 24, 24, 24, 24, 25, 25, 25, 25, 26,
+	26, 26, 26, 27, 27, 27, 27, 28, 28, 28, 29,
+	29, 29, 29, 30, 30, 30, 31, 31, 31, 31, 32,
+	32, 32, 33, 33, 33, 34, 34, 34, 35, 35, 35,
+	35, 36, 36, 36, 37, 37, 37, 38, 38, 38, 39,
+	39, 40, 40, 40, 41, 41, 41, 42, 42, 42, 43,
+	43, 43, 44, 44, 45, 45, 45, 46, 46, 46, 47,
+	47, 48, 48, 48, 49, 49, 50, 50, 50, 51, 51,
+	52, 52, 52, 53, 53, 54, 54, 55, 55, 55, 56,
+	56, 57, 57, 58, 58, 58, 59, 59, 60, 60, 61,
+	61, 62, 62, 63, 63, 63, 64, 64, 65, 65, 66,
+	66, 67, 67, 68, 68, 69, 69, 70, 70, 71, 71,
+	72, 72, 73, 73, 74, 74, 75, 75, 76, 76, 77,
+	77, 78, 79, 79, 80, 80, 81, 81, 82, 82, 83,
+	83, 84, 85, 85, 86, 86, 87, 87, 88, 89, 89,
+	90, 90, 91, 92, 92, 93, 93, 94, 95, 95, 96,
+	96, 97, 98, 98, 99, 99, 100, 101, 101, 102, 103,
+	103, 104, 105, 105, 106, 106, 107, 108, 108, 109, 110,
+	110, 111, 112, 112, 113, 114, 115, 115, 116, 117, 117,
+	118, 119, 119, 120, 121, 122, 122, 123, 124, 124, 125,
+	126, 127, 127, 128, 129, 130, 130, 131, 132, 132, 133,
+	134, 135, 136, 136, 137, 138, 139, 139, 140, 141, 142,
+	143, 143, 144, 145, 146, 146, 147, 148, 149, 150, 151,
+	151, 152, 153, 154, 155, 155, 156, 157, 158, 159, 160,
+	161, 161, 162, 163, 164, 165, 166, 167, 167, 168, 169,
+	170, 171, 172, 173, 174, 175, 175, 176, 177, 178, 179,
+	180, 181, 182, 183, 184, 185, 186, 186, 187, 188, 189,
+	190, 191, 192, 193, 194, 195, 196, 197, 198, 199, 200,
+	201, 202, 203, 204, 205, 206, 207, 208, 209, 210, 211,
+	212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222,
+	223, 224, 225, 226, 228, 229, 230, 231, 232, 233, 234,
+	235, 236, 237, 238, 239, 241, 242, 243, 244, 245, 246,
+	247, 248, 249, 251, 252, 253, 254, 255, 256, 257, 259,
+	260, 261, 262, 263, 264, 266, 267, 268, 269, 270, 272,
+	273, 274, 275, 276, 278, 279, 280, 281, 282, 284, 285,
+	286, 287, 289, 290, 291, 292, 294, 295, 296, 297, 299,
+	300, 301, 302, 304, 305, 306, 308, 309, 310, 311, 313,
+	314, 315, 317, 318, 319, 321, 322, 323, 325, 326, 327,
+	329, 330, 331, 333, 334, 336, 337, 338, 340, 341, 342,
+	344, 345, 347, 348, 349, 351, 352, 354, 355, 356, 358,
+	359, 361, 362, 364, 365, 366, 368, 369, 371, 372, 374,
+	375, 377, 378, 380, 381, 383, 384, 386, 387, 389, 390,
+	392, 393, 395, 396, 398, 399, 401, 402, 404, 405, 407,
+	408, 410, 412, 413, 415, 416, 418, 419, 421, 423, 424,
+	426, 427, 429, 431, 432, 434, 435, 437, 439, 440, 442,
+	444, 445, 447, 448, 450, 452, 453, 455, 457, 458, 460,
+	462, 463, 465, 467, 468, 470, 472, 474, 475, 477, 479,
+	480, 482, 484, 486, 487, 489, 491, 493, 494, 496, 498,
+	500, 501, 503, 505, 507, 509, 510, 512, 514, 516, 518,
+	519, 521, 523, 525, 527, 528, 530, 532, 534, 536, 538,
+	539, 541, 543, 545, 547, 549, 551, 553, 554, 556, 558,
+	560, 562, 564, 566, 568, 570, 572, 574, 575, 577, 579,
+	581, 583, 585, 587, 589, 591, 593, 595, 597, 599, 601,
+	603, 605, 607, 609, 611, 613, 615, 617, 619, 621, 623,
+	625, 627, 629, 631, 633, 635, 637, 640, 642, 644, 646,
+	648, 650, 652, 654, 656, 658, 660, 663, 665, 667, 669,
+	671, 673, 675, 678, 680, 682, 684, 686, 688, 690, 693,
+	695, 697, 699, 701, 704, 706, 708, 710, 712, 715, 717,
+	719, 721, 724, 726, 728, 730, 733, 735, 737, 739, 742,
+	744, 746, 749, 751, 753, 755, 758, 760, 762, 765, 767,
+	769, 772, 774, 776, 779, 781, 783, 786, 788, 790, 793,
+	795, 798, 800, 802, 805, 807, 810, 812, 814, 817, 819,
+	822, 824, 827, 829, 831, 834, 836, 839, 841, 844, 846,
+	849, 851, 854, 856, 859, 861, 864, 866, 869, 871, 874,
+	876, 879, 881, 884, 887, 889, 892, 894, 897, 899, 902,
+	905, 907, 910, 912, 915, 918, 920, 923, 925, 928, 931,
+	933, 936, 939, 941, 944, 947, 949, 952, 955, 957, 960,
+	963, 965, 968, 971, 973, 976, 979, 982, 984, 987, 990,
+	992, 995, 998, 1001, 1004, 1006, 1009, 1012, 1015, 1017, 1020,
+	1023,
+};
+
+static const u16 xgamma10_29[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 6, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 8, 9,
+	9, 9, 9, 9, 9, 9, 10, 10, 10, 10, 10,
+	10, 10, 11, 11, 11, 11, 11, 11, 11, 12, 12,
+	12, 12, 12, 12, 13, 13, 13, 13, 13, 13, 13,
+	14, 14, 14, 14, 14, 15, 15, 15, 15, 15, 15,
+	16, 16, 16, 16, 16, 17, 17, 17, 17, 17, 18,
+	18, 18, 18, 18, 19, 19, 19, 19, 19, 20, 20,
+	20, 20, 21, 21, 21, 21, 21, 22, 22, 22, 22,
+	23, 23, 23, 23, 24, 24, 24, 24, 25, 25, 25,
+	25, 26, 26, 26, 26, 27, 27, 27, 28, 28, 28,
+	28, 29, 29, 29, 29, 30, 30, 30, 31, 31, 31,
+	31, 32, 32, 32, 33, 33, 33, 34, 34, 34, 35,
+	35, 35, 35, 36, 36, 36, 37, 37, 37, 38, 38,
+	38, 39, 39, 39, 40, 40, 41, 41, 41, 42, 42,
+	42, 43, 43, 43, 44, 44, 44, 45, 45, 46, 46,
+	46, 47, 47, 48, 48, 48, 49, 49, 49, 50, 50,
+	51, 51, 52, 52, 52, 53, 53, 54, 54, 54, 55,
+	55, 56, 56, 57, 57, 57, 58, 58, 59, 59, 60,
+	60, 61, 61, 61, 62, 62, 63, 63, 64, 64, 65,
+	65, 66, 66, 67, 67, 68, 68, 69, 69, 70, 70,
+	71, 71, 72, 72, 73, 73, 74, 74, 75, 75, 76,
+	76, 77, 77, 78, 78, 79, 80, 80, 81, 81, 82,
+	82, 83, 83, 84, 85, 85, 86, 86, 87, 87, 88,
+	89, 89, 90, 90, 91, 92, 92, 93, 93, 94, 95,
+	95, 96, 96, 97, 98, 98, 99, 99, 100, 101, 101,
+	102, 103, 103, 104, 105, 105, 106, 107, 107, 108, 109,
+	109, 110, 111, 111, 112, 113, 113, 114, 115, 115, 116,
+	117, 117, 118, 119, 120, 120, 121, 122, 122, 123, 124,
+	125, 125, 126, 127, 128, 128, 129, 130, 131, 131, 132,
+	133, 134, 134, 135, 136, 137, 137, 138, 139, 140, 141,
+	141, 142, 143, 144, 145, 145, 146, 147, 148, 149, 149,
+	150, 151, 152, 153, 154, 154, 155, 156, 157, 158, 159,
+	160, 160, 161, 162, 163, 164, 165, 166, 166, 167, 168,
+	169, 170, 171, 172, 173, 174, 175, 175, 176, 177, 178,
+	179, 180, 181, 182, 183, 184, 185, 186, 187, 188, 189,
+	190, 190, 191, 192, 193, 194, 195, 196, 197, 198, 199,
+	200, 201, 202, 203, 204, 205, 206, 207, 208, 209, 210,
+	211, 212, 214, 215, 216, 217, 218, 219, 220, 221, 222,
+	223, 224, 225, 226, 227, 228, 229, 231, 232, 233, 234,
+	235, 236, 237, 238, 239, 241, 242, 243, 244, 245, 246,
+	247, 248, 250, 251, 252, 253, 254, 255, 257, 258, 259,
+	260, 261, 263, 264, 265, 266, 267, 269, 270, 271, 272,
+	273, 275, 276, 277, 278, 280, 281, 282, 283, 285, 286,
+	287, 288, 290, 291, 292, 293, 295, 296, 297, 299, 300,
+	301, 302, 304, 305, 306, 308, 309, 310, 312, 313, 314,
+	316, 317, 318, 320, 321, 322, 324, 325, 327, 328, 329,
+	331, 332, 333, 335, 336, 338, 339, 340, 342, 343, 345,
+	346, 348, 349, 350, 352, 353, 355, 356, 358, 359, 361,
+	362, 363, 365, 366, 368, 369, 371, 372, 374, 375, 377,
+	378, 380, 381, 383, 384, 386, 388, 389, 391, 392, 394,
+	395, 397, 398, 400, 402, 403, 405, 406, 408, 409, 411,
+	413, 414, 416, 417, 419, 421, 422, 424, 426, 427, 429,
+	430, 432, 434, 435, 437, 439, 440, 442, 444, 445, 447,
+	449, 450, 452, 454, 456, 457, 459, 461, 462, 464, 466,
+	468, 469, 471, 473, 475, 476, 478, 480, 482, 483, 485,
+	487, 489, 491, 492, 494, 496, 498, 500, 501, 503, 505,
+	507, 509, 511, 512, 514, 516, 518, 520, 522, 524, 525,
+	527, 529, 531, 533, 535, 537, 539, 541, 542, 544, 546,
+	548, 550, 552, 554, 556, 558, 560, 562, 564, 566, 568,
+	570, 572, 574, 576, 578, 580, 582, 584, 586, 588, 590,
+	592, 594, 596, 598, 600, 602, 604, 606, 608, 610, 612,
+	614, 616, 618, 621, 623, 625, 627, 629, 631, 633, 635,
+	637, 640, 642, 644, 646, 648, 650, 652, 655, 657, 659,
+	661, 663, 665, 668, 670, 672, 674, 676, 679, 681, 683,
+	685, 688, 690, 692, 694, 697, 699, 701, 703, 706, 708,
+	710, 712, 715, 717, 719, 722, 724, 726, 729, 731, 733,
+	736, 738, 740, 743, 745, 747, 750, 752, 754, 757, 759,
+	762, 764, 766, 769, 771, 774, 776, 778, 781, 783, 786,
+	788, 791, 793, 795, 798, 800, 803, 805, 808, 810, 813,
+	815, 818, 820, 823, 825, 828, 830, 833, 835, 838, 841,
+	843, 846, 848, 851, 853, 856, 859, 861, 864, 866, 869,
+	872, 874, 877, 879, 882, 885, 887, 890, 893, 895, 898,
+	901, 903, 906, 909, 911, 914, 917, 919, 922, 925, 927,
+	930, 933, 936, 938, 941, 944, 947, 949, 952, 955, 958,
+	960, 963, 966, 969, 972, 974, 977, 980, 983, 986, 989,
+	991, 994, 997, 1000, 1003, 1006, 1009, 1011, 1014, 1017, 1020,
+	1023,
+};
+
+static const u16 xgamma10_30[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 5, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 6, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 8, 9,
+	9, 9, 9, 9, 9, 9, 9, 10, 10, 10, 10,
+	10, 10, 10, 11, 11, 11, 11, 11, 11, 11, 12,
+	12, 12, 12, 12, 12, 13, 13, 13, 13, 13, 13,
+	14, 14, 14, 14, 14, 14, 15, 15, 15, 15, 15,
+	15, 16, 16, 16, 16, 16, 17, 17, 17, 17, 17,
+	18, 18, 18, 18, 18, 19, 19, 19, 19, 19, 20,
+	20, 20, 20, 21, 21, 21, 21, 21, 22, 22, 22,
+	22, 23, 23, 23, 23, 24, 24, 24, 24, 25, 25,
+	25, 25, 26, 26, 26, 26, 27, 27, 27, 27, 28,
+	28, 28, 28, 29, 29, 29, 30, 30, 30, 30, 31,
+	31, 31, 32, 32, 32, 33, 33, 33, 33, 34, 34,
+	34, 35, 35, 35, 36, 36, 36, 37, 37, 37, 38,
+	38, 38, 39, 39, 39, 40, 40, 40, 41, 41, 41,
+	42, 42, 42, 43, 43, 43, 44, 44, 45, 45, 45,
+	46, 46, 46, 47, 47, 48, 48, 48, 49, 49, 50,
+	50, 50, 51, 51, 52, 52, 52, 53, 53, 54, 54,
+	55, 55, 55, 56, 56, 57, 57, 58, 58, 58, 59,
+	59, 60, 60, 61, 61, 62, 62, 63, 63, 63, 64,
+	64, 65, 65, 66, 66, 67, 67, 68, 68, 69, 69,
+	70, 70, 71, 71, 72, 72, 73, 73, 74, 74, 75,
+	75, 76, 77, 77, 78, 78, 79, 79, 80, 80, 81,
+	81, 82, 83, 83, 84, 84, 85, 85, 86, 86, 87,
+	88, 88, 89, 89, 90, 91, 91, 92, 92, 93, 94,
+	94, 95, 95, 96, 97, 97, 98, 99, 99, 100, 100,
+	101, 102, 102, 103, 104, 104, 105, 106, 106, 107, 108,
+	108, 109, 110, 110, 111, 112, 112, 113, 114, 114, 115,
+	116, 117, 117, 118, 119, 119, 120, 121, 122, 122, 123,
+	124, 125, 125, 126, 127, 128, 128, 129, 130, 131, 131,
+	132, 133, 134, 134, 135, 136, 137, 137, 138, 139, 140,
+	141, 141, 142, 143, 144, 145, 146, 146, 147, 148, 149,
+	150, 150, 151, 152, 153, 154, 155, 156, 156, 157, 158,
+	159, 160, 161, 162, 162, 163, 164, 165, 166, 167, 168,
+	169, 170, 171, 171, 172, 173, 174, 175, 176, 177, 178,
+	179, 180, 181, 182, 183, 184, 185, 185, 186, 187, 188,
+	189, 190, 191, 192, 193, 194, 195, 196, 197, 198, 199,
+	200, 201, 202, 203, 204, 205, 206, 207, 208, 210, 211,
+	212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222,
+	223, 224, 226, 227, 228, 229, 230, 231, 232, 233, 234,
+	236, 237, 238, 239, 240, 241, 242, 244, 245, 246, 247,
+	248, 249, 250, 252, 253, 254, 255, 256, 258, 259, 260,
+	261, 262, 264, 265, 266, 267, 269, 270, 271, 272, 273,
+	275, 276, 277, 278, 280, 281, 282, 284, 285, 286, 287,
+	289, 290, 291, 293, 294, 295, 296, 298, 299, 300, 302,
+	303, 304, 306, 307, 308, 310, 311, 313, 314, 315, 317,
+	318, 319, 321, 322, 324, 325, 326, 328, 329, 331, 332,
+	333, 335, 336, 338, 339, 341, 342, 343, 345, 346, 348,
+	349, 351, 352, 354, 355, 357, 358, 360, 361, 363, 364,
+	366, 367, 369, 370, 372, 373, 375, 376, 378, 379, 381,
+	383, 384, 386, 387, 389, 390, 392, 394, 395, 397, 398,
+	400, 402, 403, 405, 406, 408, 410, 411, 413, 415, 416,
+	418, 419, 421, 423, 424, 426, 428, 429, 431, 433, 435,
+	436, 438, 440, 441, 443, 445, 447, 448, 450, 452, 453,
+	455, 457, 459, 460, 462, 464, 466, 468, 469, 471, 473,
+	475, 477, 478, 480, 482, 484, 486, 487, 489, 491, 493,
+	495, 497, 498, 500, 502, 504, 506, 508, 510, 512, 513,
+	515, 517, 519, 521, 523, 525, 527, 529, 531, 533, 535,
+	537, 539, 540, 542, 544, 546, 548, 550, 552, 554, 556,
+	558, 560, 562, 564, 566, 568, 570, 572, 574, 577, 579,
+	581, 583, 585, 587, 589, 591, 593, 595, 597, 599, 601,
+	604, 606, 608, 610, 612, 614, 616, 618, 621, 623, 625,
+	627, 629, 631, 634, 636, 638, 640, 642, 645, 647, 649,
+	651, 653, 656, 658, 660, 662, 665, 667, 669, 671, 674,
+	676, 678, 680, 683, 685, 687, 690, 692, 694, 697, 699,
+	701, 704, 706, 708, 711, 713, 715, 718, 720, 722, 725,
+	727, 730, 732, 734, 737, 739, 742, 744, 746, 749, 751,
+	754, 756, 759, 761, 764, 766, 769, 771, 774, 776, 779,
+	781, 784, 786, 789, 791, 794, 796, 799, 801, 804, 806,
+	809, 812, 814, 817, 819, 822, 824, 827, 830, 832, 835,
+	837, 840, 843, 845, 848, 851, 853, 856, 859, 861, 864,
+	867, 869, 872, 875, 878, 880, 883, 886, 888, 891, 894,
+	897, 899, 902, 905, 908, 910, 913, 916, 919, 922, 924,
+	927, 930, 933, 936, 938, 941, 944, 947, 950, 953, 956,
+	958, 961, 964, 967, 970, 973, 976, 979, 982, 984, 987,
+	990, 993, 996, 999, 1002, 1005, 1008, 1011, 1014, 1017, 1020,
+	1023,
+};
+
+static const u16 xgamma10_31[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 6, 6, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 8, 9,
+	9, 9, 9, 9, 9, 9, 9, 10, 10, 10, 10,
+	10, 10, 10, 11, 11, 11, 11, 11, 11, 11, 12,
+	12, 12, 12, 12, 12, 12, 13, 13, 13, 13, 13,
+	13, 14, 14, 14, 14, 14, 14, 15, 15, 15, 15,
+	15, 16, 16, 16, 16, 16, 16, 17, 17, 17, 17,
+	17, 18, 18, 18, 18, 18, 19, 19, 19, 19, 19,
+	20, 20, 20, 20, 21, 21, 21, 21, 21, 22, 22,
+	22, 22, 23, 23, 23, 23, 24, 24, 24, 24, 25,
+	25, 25, 25, 26, 26, 26, 26, 27, 27, 27, 27,
+	28, 28, 28, 28, 29, 29, 29, 30, 30, 30, 30,
+	31, 31, 31, 32, 32, 32, 32, 33, 33, 33, 34,
+	34, 34, 35, 35, 35, 36, 36, 36, 36, 37, 37,
+	37, 38, 38, 38, 39, 39, 39, 40, 40, 41, 41,
+	41, 42, 42, 42, 43, 43, 43, 44, 44, 44, 45,
+	45, 46, 46, 46, 47, 47, 47, 48, 48, 49, 49,
+	49, 50, 50, 51, 51, 51, 52, 52, 53, 53, 54,
+	54, 54, 55, 55, 56, 56, 57, 57, 57, 58, 58,
+	59, 59, 60, 60, 61, 61, 61, 62, 62, 63, 63,
+	64, 64, 65, 65, 66, 66, 67, 67, 68, 68, 69,
+	69, 70, 70, 71, 71, 72, 72, 73, 73, 74, 74,
+	75, 75, 76, 76, 77, 77, 78, 79, 79, 80, 80,
+	81, 81, 82, 82, 83, 84, 84, 85, 85, 86, 86,
+	87, 88, 88, 89, 89, 90, 91, 91, 92, 92, 93,
+	94, 94, 95, 95, 96, 97, 97, 98, 99, 99, 100,
+	101, 101, 102, 102, 103, 104, 104, 105, 106, 106, 107,
+	108, 108, 109, 110, 111, 111, 112, 113, 113, 114, 115,
+	115, 116, 117, 118, 118, 119, 120, 120, 121, 122, 123,
+	123, 124, 125, 126, 126, 127, 128, 129, 129, 130, 131,
+	132, 132, 133, 134, 135, 136, 136, 137, 138, 139, 140,
+	140, 141, 142, 143, 144, 144, 145, 146, 147, 148, 149,
+	149, 150, 151, 152, 153, 154, 155, 155, 156, 157, 158,
+	159, 160, 161, 162, 162, 163, 164, 165, 166, 167, 168,
+	169, 170, 171, 171, 172, 173, 174, 175, 176, 177, 178,
+	179, 180, 181, 182, 183, 184, 185, 186, 187, 188, 189,
+	190, 191, 192, 193, 194, 195, 196, 197, 198, 199, 200,
+	201, 202, 203, 204, 205, 206, 207, 208, 209, 210, 211,
+	212, 213, 214, 216, 217, 218, 219, 220, 221, 222, 223,
+	224, 225, 227, 228, 229, 230, 231, 232, 233, 234, 236,
+	237, 238, 239, 240, 241, 243, 244, 245, 246, 247, 248,
+	250, 251, 252, 253, 254, 256, 257, 258, 259, 260, 262,
+	263, 264, 265, 267, 268, 269, 270, 272, 273, 274, 275,
+	277, 278, 279, 281, 282, 283, 285, 286, 287, 288, 290,
+	291, 292, 294, 295, 296, 298, 299, 300, 302, 303, 305,
+	306, 307, 309, 310, 311, 313, 314, 316, 317, 318, 320,
+	321, 323, 324, 325, 327, 328, 330, 331, 333, 334, 336,
+	337, 338, 340, 341, 343, 344, 346, 347, 349, 350, 352,
+	353, 355, 356, 358, 359, 361, 362, 364, 366, 367, 369,
+	370, 372, 373, 375, 376, 378, 380, 381, 383, 384, 386,
+	388, 389, 391, 392, 394, 396, 397, 399, 401, 402, 404,
+	406, 407, 409, 411, 412, 414, 416, 417, 419, 421, 422,
+	424, 426, 427, 429, 431, 433, 434, 436, 438, 440, 441,
+	443, 445, 447, 448, 450, 452, 454, 456, 457, 459, 461,
+	463, 465, 466, 468, 470, 472, 474, 476, 477, 479, 481,
+	483, 485, 487, 489, 490, 492, 494, 496, 498, 500, 502,
+	504, 506, 508, 510, 511, 513, 515, 517, 519, 521, 523,
+	525, 527, 529, 531, 533, 535, 537, 539, 541, 543, 545,
+	547, 549, 551, 553, 555, 557, 559, 561, 564, 566, 568,
+	570, 572, 574, 576, 578, 580, 582, 584, 587, 589, 591,
+	593, 595, 597, 599, 602, 604, 606, 608, 610, 613, 615,
+	617, 619, 621, 624, 626, 628, 630, 632, 635, 637, 639,
+	641, 644, 646, 648, 651, 653, 655, 657, 660, 662, 664,
+	667, 669, 671, 674, 676, 678, 681, 683, 685, 688, 690,
+	692, 695, 697, 700, 702, 704, 707, 709, 712, 714, 717,
+	719, 721, 724, 726, 729, 731, 734, 736, 739, 741, 744,
+	746, 749, 751, 754, 756, 759, 761, 764, 766, 769, 772,
+	774, 777, 779, 782, 784, 787, 790, 792, 795, 797, 800,
+	803, 805, 808, 811, 813, 816, 819, 821, 824, 827, 829,
+	832, 835, 837, 840, 843, 845, 848, 851, 854, 856, 859,
+	862, 865, 867, 870, 873, 876, 879, 881, 884, 887, 890,
+	893, 895, 898, 901, 904, 907, 910, 913, 915, 918, 921,
+	924, 927, 930, 933, 936, 939, 942, 945, 947, 950, 953,
+	956, 959, 962, 965, 968, 971, 974, 977, 980, 983, 986,
+	989, 992, 995, 998, 1001, 1005, 1008, 1011, 1014, 1017, 1020,
+	1023,
+};
+
+static const u16 xgamma10_32[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 6, 6, 6, 6, 6, 6, 6, 6, 6,
+	6, 6, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	7, 8, 8, 8, 8, 8, 8, 8, 8, 9, 9,
+	9, 9, 9, 9, 9, 9, 9, 10, 10, 10, 10,
+	10, 10, 10, 11, 11, 11, 11, 11, 11, 11, 12,
+	12, 12, 12, 12, 12, 12, 13, 13, 13, 13, 13,
+	13, 14, 14, 14, 14, 14, 14, 15, 15, 15, 15,
+	15, 15, 16, 16, 16, 16, 16, 17, 17, 17, 17,
+	17, 18, 18, 18, 18, 18, 19, 19, 19, 19, 19,
+	20, 20, 20, 20, 20, 21, 21, 21, 21, 22, 22,
+	22, 22, 22, 23, 23, 23, 23, 24, 24, 24, 24,
+	25, 25, 25, 25, 26, 26, 26, 26, 27, 27, 27,
+	27, 28, 28, 28, 28, 29, 29, 29, 30, 30, 30,
+	30, 31, 31, 31, 32, 32, 32, 32, 33, 33, 33,
+	34, 34, 34, 35, 35, 35, 36, 36, 36, 37, 37,
+	37, 37, 38, 38, 38, 39, 39, 39, 40, 40, 41,
+	41, 41, 42, 42, 42, 43, 43, 43, 44, 44, 44,
+	45, 45, 46, 46, 46, 47, 47, 48, 48, 48, 49,
+	49, 49, 50, 50, 51, 51, 51, 52, 52, 53, 53,
+	54, 54, 54, 55, 55, 56, 56, 57, 57, 57, 58,
+	58, 59, 59, 60, 60, 61, 61, 62, 62, 62, 63,
+	63, 64, 64, 65, 65, 66, 66, 67, 67, 68, 68,
+	69, 69, 70, 70, 71, 71, 72, 72, 73, 73, 74,
+	74, 75, 75, 76, 77, 77, 78, 78, 79, 79, 80,
+	80, 81, 81, 82, 83, 83, 84, 84, 85, 85, 86,
+	87, 87, 88, 88, 89, 90, 90, 91, 91, 92, 93,
+	93, 94, 95, 95, 96, 96, 97, 98, 98, 99, 100,
+	100, 101, 102, 102, 103, 104, 104, 105, 106, 106, 107,
+	108, 108, 109, 110, 110, 111, 112, 112, 113, 114, 114,
+	115, 116, 117, 117, 118, 119, 120, 120, 121, 122, 122,
+	123, 124, 125, 125, 126, 127, 128, 129, 129, 130, 131,
+	132, 132, 133, 134, 135, 136, 136, 137, 138, 139, 140,
+	140, 141, 142, 143, 144, 145, 145, 146, 147, 148, 149,
+	150, 150, 151, 152, 153, 154, 155, 156, 157, 157, 158,
+	159, 160, 161, 162, 163, 164, 165, 166, 166, 167, 168,
+	169, 170, 171, 172, 173, 174, 175, 176, 177, 178, 179,
+	180, 181, 182, 183, 184, 185, 186, 186, 187, 188, 189,
+	190, 192, 193, 194, 195, 196, 197, 198, 199, 200, 201,
+	202, 203, 204, 205, 206, 207, 208, 209, 210, 211, 212,
+	214, 215, 216, 217, 218, 219, 220, 221, 222, 224, 225,
+	226, 227, 228, 229, 230, 231, 233, 234, 235, 236, 237,
+	238, 240, 241, 242, 243, 244, 246, 247, 248, 249, 250,
+	252, 253, 254, 255, 257, 258, 259, 260, 262, 263, 264,
+	265, 267, 268, 269, 270, 272, 273, 274, 276, 277, 278,
+	280, 281, 282, 283, 285, 286, 287, 289, 290, 291, 293,
+	294, 296, 297, 298, 300, 301, 302, 304, 305, 307, 308,
+	309, 311, 312, 314, 315, 316, 318, 319, 321, 322, 324,
+	325, 327, 328, 330, 331, 332, 334, 335, 337, 338, 340,
+	341, 343, 344, 346, 347, 349, 351, 352, 354, 355, 357,
+	358, 360, 361, 363, 364, 366, 368, 369, 371, 372, 374,
+	376, 377, 379, 380, 382, 384, 385, 387, 389, 390, 392,
+	394, 395, 397, 399, 400, 402, 404, 405, 407, 409, 410,
+	412, 414, 416, 417, 419, 421, 423, 424, 426, 428, 430,
+	431, 433, 435, 437, 438, 440, 442, 444, 446, 447, 449,
+	451, 453, 455, 457, 458, 460, 462, 464, 466, 468, 469,
+	471, 473, 475, 477, 479, 481, 483, 485, 487, 488, 490,
+	492, 494, 496, 498, 500, 502, 504, 506, 508, 510, 512,
+	514, 516, 518, 520, 522, 524, 526, 528, 530, 532, 534,
+	536, 538, 540, 542, 544, 547, 549, 551, 553, 555, 557,
+	559, 561, 563, 565, 568, 570, 572, 574, 576, 578, 581,
+	583, 585, 587, 589, 591, 594, 596, 598, 600, 602, 605,
+	607, 609, 611, 614, 616, 618, 620, 623, 625, 627, 630,
+	632, 634, 636, 639, 641, 643, 646, 648, 650, 653, 655,
+	657, 660, 662, 665, 667, 669, 672, 674, 677, 679, 681,
+	684, 686, 689, 691, 694, 696, 698, 701, 703, 706, 708,
+	711, 713, 716, 718, 721, 723, 726, 728, 731, 734, 736,
+	739, 741, 744, 746, 749, 751, 754, 757, 759, 762, 765,
+	767, 770, 772, 775, 778, 780, 783, 786, 788, 791, 794,
+	796, 799, 802, 804, 807, 810, 813, 815, 818, 821, 824,
+	826, 829, 832, 835, 838, 840, 843, 846, 849, 852, 854,
+	857, 860, 863, 866, 869, 871, 874, 877, 880, 883, 886,
+	889, 892, 895, 897, 900, 903, 906, 909, 912, 915, 918,
+	921, 924, 927, 930, 933, 936, 939, 942, 945, 948, 951,
+	954, 957, 960, 963, 967, 970, 973, 976, 979, 982, 985,
+	988, 991, 994, 998, 1001, 1004, 1007, 1010, 1013, 1017, 1020,
+	1023,
+};
+
+static const u16 xgamma10_33[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	5, 6, 6, 6, 6, 6, 6, 6, 6, 6, 6,
+	6, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	8, 8, 8, 8, 8, 8, 8, 8, 8, 9, 9,
+	9, 9, 9, 9, 9, 9, 10, 10, 10, 10, 10,
+	10, 10, 10, 11, 11, 11, 11, 11, 11, 11, 12,
+	12, 12, 12, 12, 12, 12, 13, 13, 13, 13, 13,
+	13, 14, 14, 14, 14, 14, 14, 15, 15, 15, 15,
+	15, 15, 16, 16, 16, 16, 16, 17, 17, 17, 17,
+	17, 17, 18, 18, 18, 18, 18, 19, 19, 19, 19,
+	19, 20, 20, 20, 20, 21, 21, 21, 21, 21, 22,
+	22, 22, 22, 23, 23, 23, 23, 23, 24, 24, 24,
+	24, 25, 25, 25, 25, 26, 26, 26, 26, 27, 27,
+	27, 28, 28, 28, 28, 29, 29, 29, 29, 30, 30,
+	30, 31, 31, 31, 31, 32, 32, 32, 33, 33, 33,
+	33, 34, 34, 34, 35, 35, 35, 36, 36, 36, 37,
+	37, 37, 38, 38, 38, 39, 39, 39, 40, 40, 40,
+	41, 41, 41, 42, 42, 42, 43, 43, 44, 44, 44,
+	45, 45, 45, 46, 46, 47, 47, 47, 48, 48, 48,
+	49, 49, 50, 50, 50, 51, 51, 52, 52, 53, 53,
+	53, 54, 54, 55, 55, 55, 56, 56, 57, 57, 58,
+	58, 59, 59, 59, 60, 60, 61, 61, 62, 62, 63,
+	63, 64, 64, 65, 65, 66, 66, 67, 67, 68, 68,
+	69, 69, 70, 70, 71, 71, 72, 72, 73, 73, 74,
+	74, 75, 75, 76, 76, 77, 77, 78, 79, 79, 80,
+	80, 81, 81, 82, 82, 83, 84, 84, 85, 85, 86,
+	87, 87, 88, 88, 89, 90, 90, 91, 91, 92, 93,
+	93, 94, 94, 95, 96, 96, 97, 98, 98, 99, 100,
+	100, 101, 102, 102, 103, 104, 104, 105, 106, 106, 107,
+	108, 108, 109, 110, 110, 111, 112, 112, 113, 114, 115,
+	115, 116, 117, 118, 118, 119, 120, 120, 121, 122, 123,
+	123, 124, 125, 126, 127, 127, 128, 129, 130, 130, 131,
+	132, 133, 134, 134, 135, 136, 137, 138, 138, 139, 140,
+	141, 142, 143, 143, 144, 145, 146, 147, 148, 148, 149,
+	150, 151, 152, 153, 154, 155, 155, 156, 157, 158, 159,
+	160, 161, 162, 163, 164, 165, 165, 166, 167, 168, 169,
+	170, 171, 172, 173, 174, 175, 176, 177, 178, 179, 180,
+	181, 182, 183, 184, 185, 186, 187, 188, 189, 190, 191,
+	192, 193, 194, 195, 196, 197, 198, 199, 200, 201, 202,
+	203, 204, 206, 207, 208, 209, 210, 211, 212, 213, 214,
+	215, 216, 218, 219, 220, 221, 222, 223, 224, 226, 227,
+	228, 229, 230, 231, 233, 234, 235, 236, 237, 238, 240,
+	241, 242, 243, 245, 246, 247, 248, 249, 251, 252, 253,
+	254, 256, 257, 258, 259, 261, 262, 263, 265, 266, 267,
+	268, 270, 271, 272, 274, 275, 276, 278, 279, 280, 282,
+	283, 284, 286, 287, 288, 290, 291, 292, 294, 295, 297,
+	298, 299, 301, 302, 304, 305, 307, 308, 309, 311, 312,
+	314, 315, 317, 318, 320, 321, 322, 324, 325, 327, 328,
+	330, 331, 333, 334, 336, 337, 339, 341, 342, 344, 345,
+	347, 348, 350, 351, 353, 355, 356, 358, 359, 361, 362,
+	364, 366, 367, 369, 371, 372, 374, 375, 377, 379, 380,
+	382, 384, 385, 387, 389, 390, 392, 394, 395, 397, 399,
+	401, 402, 404, 406, 408, 409, 411, 413, 414, 416, 418,
+	420, 422, 423, 425, 427, 429, 431, 432, 434, 436, 438,
+	440, 441, 443, 445, 447, 449, 451, 453, 454, 456, 458,
+	460, 462, 464, 466, 468, 470, 472, 473, 475, 477, 479,
+	481, 483, 485, 487, 489, 491, 493, 495, 497, 499, 501,
+	503, 505, 507, 509, 511, 513, 515, 517, 519, 521, 523,
+	525, 528, 530, 532, 534, 536, 538, 540, 542, 544, 547,
+	549, 551, 553, 555, 557, 559, 562, 564, 566, 568, 570,
+	573, 575, 577, 579, 581, 584, 586, 588, 590, 593, 595,
+	597, 599, 602, 604, 606, 609, 611, 613, 615, 618, 620,
+	622, 625, 627, 629, 632, 634, 637, 639, 641, 644, 646,
+	648, 651, 653, 656, 658, 661, 663, 665, 668, 670, 673,
+	675, 678, 680, 683, 685, 688, 690, 693, 695, 698, 700,
+	703, 705, 708, 710, 713, 716, 718, 721, 723, 726, 729,
+	731, 734, 736, 739, 742, 744, 747, 750, 752, 755, 758,
+	760, 763, 766, 768, 771, 774, 776, 779, 782, 785, 787,
+	790, 793, 796, 798, 801, 804, 807, 810, 812, 815, 818,
+	821, 824, 827, 829, 832, 835, 838, 841, 844, 847, 850,
+	852, 855, 858, 861, 864, 867, 870, 873, 876, 879, 882,
+	885, 888, 891, 894, 897, 900, 903, 906, 909, 912, 915,
+	918, 921, 924, 927, 930, 933, 937, 940, 943, 946, 949,
+	952, 955, 958, 962, 965, 968, 971, 974, 978, 981, 984,
+	987, 990, 994, 997, 1000, 1003, 1007, 1010, 1013, 1016, 1020,
+	1023,
+};
+
+static const u16 xgamma10_34[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 5,
+	5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	6, 6, 6, 6, 6, 6, 6, 6, 6, 6, 6,
+	6, 7, 7, 7, 7, 7, 7, 7, 7, 7, 8,
+	8, 8, 8, 8, 8, 8, 8, 8, 8, 9, 9,
+	9, 9, 9, 9, 9, 9, 10, 10, 10, 10, 10,
+	10, 10, 10, 11, 11, 11, 11, 11, 11, 11, 12,
+	12, 12, 12, 12, 12, 12, 13, 13, 13, 13, 13,
+	13, 14, 14, 14, 14, 14, 14, 15, 15, 15, 15,
+	15, 15, 16, 16, 16, 16, 16, 17, 17, 17, 17,
+	17, 17, 18, 18, 18, 18, 18, 19, 19, 19, 19,
+	19, 20, 20, 20, 20, 21, 21, 21, 21, 21, 22,
+	22, 22, 22, 23, 23, 23, 23, 23, 24, 24, 24,
+	24, 25, 25, 25, 25, 26, 26, 26, 26, 27, 27,
+	27, 27, 28, 28, 28, 29, 29, 29, 29, 30, 30,
+	30, 30, 31, 31, 31, 32, 32, 32, 33, 33, 33,
+	33, 34, 34, 34, 35, 35, 35, 36, 36, 36, 37,
+	37, 37, 38, 38, 38, 39, 39, 39, 40, 40, 40,
+	41, 41, 41, 42, 42, 42, 43, 43, 43, 44, 44,
+	45, 45, 45, 46, 46, 46, 47, 47, 48, 48, 48,
+	49, 49, 50, 50, 50, 51, 51, 52, 52, 52, 53,
+	53, 54, 54, 55, 55, 55, 56, 56, 57, 57, 58,
+	58, 59, 59, 59, 60, 60, 61, 61, 62, 62, 63,
+	63, 64, 64, 65, 65, 66, 66, 67, 67, 68, 68,
+	69, 69, 70, 70, 71, 71, 72, 72, 73, 73, 74,
+	74, 75, 75, 76, 76, 77, 78, 78, 79, 79, 80,
+	80, 81, 81, 82, 83, 83, 84, 84, 85, 86, 86,
+	87, 87, 88, 88, 89, 90, 90, 91, 92, 92, 93,
+	93, 94, 95, 95, 96, 97, 97, 98, 99, 99, 100,
+	101, 101, 102, 102, 103, 104, 105, 105, 106, 107, 107,
+	108, 109, 109, 110, 111, 111, 112, 113, 114, 114, 115,
+	116, 117, 117, 118, 119, 119, 120, 121, 122, 123, 123,
+	124, 125, 126, 126, 127, 128, 129, 129, 130, 131, 132,
+	133, 133, 134, 135, 136, 137, 138, 138, 139, 140, 141,
+	142, 143, 143, 144, 145, 146, 147, 148, 149, 149, 150,
+	151, 152, 153, 154, 155, 156, 157, 157, 158, 159, 160,
+	161, 162, 163, 164, 165, 166, 167, 168, 169, 170, 171,
+	172, 172, 173, 174, 175, 176, 177, 178, 179, 180, 181,
+	182, 183, 184, 185, 186, 187, 188, 189, 191, 192, 193,
+	194, 195, 196, 197, 198, 199, 200, 201, 202, 203, 204,
+	205, 207, 208, 209, 210, 211, 212, 213, 214, 215, 217,
+	218, 219, 220, 221, 222, 223, 225, 226, 227, 228, 229,
+	231, 232, 233, 234, 235, 237, 238, 239, 240, 241, 243,
+	244, 245, 246, 248, 249, 250, 251, 253, 254, 255, 256,
+	258, 259, 260, 262, 263, 264, 266, 267, 268, 269, 271,
+	272, 273, 275, 276, 278, 279, 280, 282, 283, 284, 286,
+	287, 288, 290, 291, 293, 294, 296, 297, 298, 300, 301,
+	303, 304, 306, 307, 308, 310, 311, 313, 314, 316, 317,
+	319, 320, 322, 323, 325, 326, 328, 329, 331, 332, 334,
+	335, 337, 339, 340, 342, 343, 345, 346, 348, 350, 351,
+	353, 354, 356, 358, 359, 361, 363, 364, 366, 367, 369,
+	371, 372, 374, 376, 377, 379, 381, 383, 384, 386, 388,
+	389, 391, 393, 395, 396, 398, 400, 402, 403, 405, 407,
+	409, 410, 412, 414, 416, 418, 419, 421, 423, 425, 427,
+	429, 430, 432, 434, 436, 438, 440, 442, 443, 445, 447,
+	449, 451, 453, 455, 457, 459, 461, 463, 464, 466, 468,
+	470, 472, 474, 476, 478, 480, 482, 484, 486, 488, 490,
+	492, 494, 496, 498, 500, 503, 505, 507, 509, 511, 513,
+	515, 517, 519, 521, 523, 526, 528, 530, 532, 534, 536,
+	538, 541, 543, 545, 547, 549, 551, 554, 556, 558, 560,
+	563, 565, 567, 569, 572, 574, 576, 578, 581, 583, 585,
+	587, 590, 592, 594, 597, 599, 601, 604, 606, 608, 611,
+	613, 615, 618, 620, 623, 625, 627, 630, 632, 635, 637,
+	640, 642, 644, 647, 649, 652, 654, 657, 659, 662, 664,
+	667, 669, 672, 674, 677, 679, 682, 685, 687, 690, 692,
+	695, 697, 700, 703, 705, 708, 711, 713, 716, 718, 721,
+	724, 726, 729, 732, 734, 737, 740, 743, 745, 748, 751,
+	753, 756, 759, 762, 764, 767, 770, 773, 776, 778, 781,
+	784, 787, 790, 793, 795, 798, 801, 804, 807, 810, 813,
+	815, 818, 821, 824, 827, 830, 833, 836, 839, 842, 845,
+	848, 851, 854, 857, 860, 863, 866, 869, 872, 875, 878,
+	881, 884, 887, 890, 893, 896, 899, 903, 906, 909, 912,
+	915, 918, 921, 925, 928, 931, 934, 937, 940, 944, 947,
+	950, 953, 957, 960, 963, 966, 970, 973, 976, 979, 983,
+	986, 989, 993, 996, 999, 1003, 1006, 1009, 1013, 1016, 1020,
+	1023,
+};
+
+static const u16 xgamma10_35[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 5, 5,
+	5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 6,
+	6, 6, 6, 6, 6, 6, 6, 6, 6, 6, 6,
+	7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 8,
+	8, 8, 8, 8, 8, 8, 8, 8, 9, 9, 9,
+	9, 9, 9, 9, 9, 10, 10, 10, 10, 10, 10,
+	10, 10, 11, 11, 11, 11, 11, 11, 11, 12, 12,
+	12, 12, 12, 12, 12, 13, 13, 13, 13, 13, 13,
+	13, 14, 14, 14, 14, 14, 14, 15, 15, 15, 15,
+	15, 15, 16, 16, 16, 16, 16, 17, 17, 17, 17,
+	17, 18, 18, 18, 18, 18, 18, 19, 19, 19, 19,
+	20, 20, 20, 20, 20, 21, 21, 21, 21, 21, 22,
+	22, 22, 22, 23, 23, 23, 23, 23, 24, 24, 24,
+	24, 25, 25, 25, 25, 26, 26, 26, 26, 27, 27,
+	27, 27, 28, 28, 28, 29, 29, 29, 29, 30, 30,
+	30, 31, 31, 31, 31, 32, 32, 32, 33, 33, 33,
+	33, 34, 34, 34, 35, 35, 35, 36, 36, 36, 37,
+	37, 37, 38, 38, 38, 39, 39, 39, 40, 40, 40,
+	41, 41, 41, 42, 42, 42, 43, 43, 43, 44, 44,
+	45, 45, 45, 46, 46, 47, 47, 47, 48, 48, 48,
+	49, 49, 50, 50, 50, 51, 51, 52, 52, 53, 53,
+	53, 54, 54, 55, 55, 56, 56, 56, 57, 57, 58,
+	58, 59, 59, 60, 60, 60, 61, 61, 62, 62, 63,
+	63, 64, 64, 65, 65, 66, 66, 67, 67, 68, 68,
+	69, 69, 70, 70, 71, 71, 72, 72, 73, 73, 74,
+	75, 75, 76, 76, 77, 77, 78, 78, 79, 79, 80,
+	81, 81, 82, 82, 83, 84, 84, 85, 85, 86, 86,
+	87, 88, 88, 89, 89, 90, 91, 91, 92, 93, 93,
+	94, 95, 95, 96, 96, 97, 98, 98, 99, 100, 100,
+	101, 102, 102, 103, 104, 104, 105, 106, 107, 107, 108,
+	109, 109, 110, 111, 111, 112, 113, 114, 114, 115, 116,
+	117, 117, 118, 119, 120, 120, 121, 122, 123, 123, 124,
+	125, 126, 126, 127, 128, 129, 130, 130, 131, 132, 133,
+	134, 135, 135, 136, 137, 138, 139, 140, 140, 141, 142,
+	143, 144, 145, 146, 146, 147, 148, 149, 150, 151, 152,
+	153, 154, 154, 155, 156, 157, 158, 159, 160, 161, 162,
+	163, 164, 165, 166, 167, 167, 168, 169, 170, 171, 172,
+	173, 174, 175, 176, 177, 178, 179, 180, 181, 182, 183,
+	184, 185, 186, 188, 189, 190, 191, 192, 193, 194, 195,
+	196, 197, 198, 199, 200, 201, 202, 204, 205, 206, 207,
+	208, 209, 210, 211, 213, 214, 215, 216, 217, 218, 219,
+	221, 222, 223, 224, 225, 227, 228, 229, 230, 231, 233,
+	234, 235, 236, 237, 239, 240, 241, 242, 244, 245, 246,
+	247, 249, 250, 251, 253, 254, 255, 256, 258, 259, 260,
+	262, 263, 264, 266, 267, 268, 270, 271, 272, 274, 275,
+	277, 278, 279, 281, 282, 284, 285, 286, 288, 289, 291,
+	292, 293, 295, 296, 298, 299, 301, 302, 304, 305, 307,
+	308, 310, 311, 313, 314, 316, 317, 319, 320, 322, 323,
+	325, 326, 328, 329, 331, 332, 334, 336, 337, 339, 340,
+	342, 344, 345, 347, 348, 350, 352, 353, 355, 357, 358,
+	360, 362, 363, 365, 367, 368, 370, 372, 373, 375, 377,
+	378, 380, 382, 384, 385, 387, 389, 391, 392, 394, 396,
+	398, 400, 401, 403, 405, 407, 409, 410, 412, 414, 416,
+	418, 420, 421, 423, 425, 427, 429, 431, 433, 435, 436,
+	438, 440, 442, 444, 446, 448, 450, 452, 454, 456, 458,
+	460, 462, 464, 466, 468, 470, 472, 474, 476, 478, 480,
+	482, 484, 486, 488, 490, 492, 494, 496, 498, 500, 503,
+	505, 507, 509, 511, 513, 515, 517, 520, 522, 524, 526,
+	528, 531, 533, 535, 537, 539, 542, 544, 546, 548, 550,
+	553, 555, 557, 560, 562, 564, 566, 569, 571, 573, 576,
+	578, 580, 583, 585, 587, 590, 592, 594, 597, 599, 602,
+	604, 606, 609, 611, 614, 616, 618, 621, 623, 626, 628,
+	631, 633, 636, 638, 641, 643, 646, 648, 651, 653, 656,
+	658, 661, 664, 666, 669, 671, 674, 677, 679, 682, 684,
+	687, 690, 692, 695, 698, 700, 703, 706, 708, 711, 714,
+	716, 719, 722, 725, 727, 730, 733, 736, 738, 741, 744,
+	747, 750, 752, 755, 758, 761, 764, 766, 769, 772, 775,
+	778, 781, 784, 787, 789, 792, 795, 798, 801, 804, 807,
+	810, 813, 816, 819, 822, 825, 828, 831, 834, 837, 840,
+	843, 846, 849, 852, 855, 858, 862, 865, 868, 871, 874,
+	877, 880, 883, 887, 890, 893, 896, 899, 902, 906, 909,
+	912, 915, 919, 922, 925, 928, 932, 935, 938, 941, 945,
+	948, 951, 955, 958, 961, 965, 968, 971, 975, 978, 982,
+	985, 988, 992, 995, 999, 1002, 1006, 1009, 1013, 1016, 1020,
+	1023,
+};
+
+static const u16 xgamma10_36[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 5, 5, 5, 5, 6, 6,
+	6, 6, 6, 6, 6, 6, 6, 6, 6, 7, 7,
+	7, 7, 7, 7, 7, 7, 7, 7, 7, 8, 8,
+	8, 8, 8, 8, 8, 8, 8, 9, 9, 9, 9,
+	9, 9, 9, 9, 10, 10, 10, 10, 10, 10, 10,
+	10, 11, 11, 11, 11, 11, 11, 11, 11, 12, 12,
+	12, 12, 12, 12, 13, 13, 13, 13, 13, 13, 13,
+	14, 14, 14, 14, 14, 14, 15, 15, 15, 15, 15,
+	15, 16, 16, 16, 16, 16, 16, 17, 17, 17, 17,
+	17, 18, 18, 18, 18, 18, 19, 19, 19, 19, 19,
+	20, 20, 20, 20, 20, 21, 21, 21, 21, 22, 22,
+	22, 22, 22, 23, 23, 23, 23, 24, 24, 24, 24,
+	25, 25, 25, 25, 26, 26, 26, 26, 27, 27, 27,
+	27, 28, 28, 28, 28, 29, 29, 29, 29, 30, 30,
+	30, 31, 31, 31, 31, 32, 32, 32, 33, 33, 33,
+	34, 34, 34, 35, 35, 35, 35, 36, 36, 36, 37,
+	37, 37, 38, 38, 38, 39, 39, 39, 40, 40, 40,
+	41, 41, 41, 42, 42, 43, 43, 43, 44, 44, 44,
+	45, 45, 46, 46, 46, 47, 47, 47, 48, 48, 49,
+	49, 49, 50, 50, 51, 51, 52, 52, 52, 53, 53,
+	54, 54, 54, 55, 55, 56, 56, 57, 57, 58, 58,
+	58, 59, 59, 60, 60, 61, 61, 62, 62, 63, 63,
+	64, 64, 65, 65, 66, 66, 67, 67, 68, 68, 69,
+	69, 70, 70, 71, 71, 72, 72, 73, 73, 74, 74,
+	75, 76, 76, 77, 77, 78, 78, 79, 79, 80, 81,
+	81, 82, 82, 83, 83, 84, 85, 85, 86, 86, 87,
+	88, 88, 89, 90, 90, 91, 91, 92, 93, 93, 94,
+	95, 95, 96, 97, 97, 98, 99, 99, 100, 101, 101,
+	102, 103, 103, 104, 105, 105, 106, 107, 107, 108, 109,
+	110, 110, 111, 112, 112, 113, 114, 115, 115, 116, 117,
+	118, 118, 119, 120, 121, 121, 122, 123, 124, 125, 125,
+	126, 127, 128, 129, 129, 130, 131, 132, 133, 133, 134,
+	135, 136, 137, 138, 138, 139, 140, 141, 142, 143, 144,
+	145, 145, 146, 147, 148, 149, 150, 151, 152, 153, 153,
+	154, 155, 156, 157, 158, 159, 160, 161, 162, 163, 164,
+	165, 166, 167, 168, 169, 170, 171, 172, 173, 174, 175,
+	176, 177, 178, 179, 180, 181, 182, 183, 184, 185, 186,
+	187, 188, 189, 190, 191, 192, 193, 194, 196, 197, 198,
+	199, 200, 201, 202, 203, 204, 205, 207, 208, 209, 210,
+	211, 212, 214, 215, 216, 217, 218, 219, 221, 222, 223,
+	224, 225, 227, 228, 229, 230, 231, 233, 234, 235, 236,
+	238, 239, 240, 241, 243, 244, 245, 247, 248, 249, 250,
+	252, 253, 254, 256, 257, 258, 260, 261, 262, 264, 265,
+	266, 268, 269, 271, 272, 273, 275, 276, 277, 279, 280,
+	282, 283, 285, 286, 287, 289, 290, 292, 293, 295, 296,
+	298, 299, 301, 302, 304, 305, 307, 308, 310, 311, 313,
+	314, 316, 317, 319, 320, 322, 324, 325, 327, 328, 330,
+	331, 333, 335, 336, 338, 339, 341, 343, 344, 346, 348,
+	349, 351, 353, 354, 356, 358, 359, 361, 363, 364, 366,
+	368, 370, 371, 373, 375, 377, 378, 380, 382, 384, 385,
+	387, 389, 391, 393, 394, 396, 398, 400, 402, 403, 405,
+	407, 409, 411, 413, 415, 416, 418, 420, 422, 424, 426,
+	428, 430, 432, 434, 436, 438, 439, 441, 443, 445, 447,
+	449, 451, 453, 455, 457, 459, 461, 463, 465, 467, 470,
+	472, 474, 476, 478, 480, 482, 484, 486, 488, 490, 492,
+	495, 497, 499, 501, 503, 505, 508, 510, 512, 514, 516,
+	518, 521, 523, 525, 527, 530, 532, 534, 536, 539, 541,
+	543, 545, 548, 550, 552, 555, 557, 559, 562, 564, 566,
+	569, 571, 573, 576, 578, 580, 583, 585, 588, 590, 592,
+	595, 597, 600, 602, 605, 607, 610, 612, 615, 617, 620,
+	622, 625, 627, 630, 632, 635, 637, 640, 642, 645, 648,
+	650, 653, 655, 658, 661, 663, 666, 669, 671, 674, 677,
+	679, 682, 685, 687, 690, 693, 695, 698, 701, 704, 706,
+	709, 712, 715, 717, 720, 723, 726, 729, 732, 734, 737,
+	740, 743, 746, 749, 751, 754, 757, 760, 763, 766, 769,
+	772, 775, 778, 781, 784, 787, 790, 793, 796, 799, 802,
+	805, 808, 811, 814, 817, 820, 823, 826, 829, 832, 835,
+	838, 842, 845, 848, 851, 854, 857, 860, 864, 867, 870,
+	873, 876, 880, 883, 886, 889, 893, 896, 899, 903, 906,
+	909, 912, 916, 919, 922, 926, 929, 932, 936, 939, 943,
+	946, 949, 953, 956, 960, 963, 967, 970, 973, 977, 980,
+	984, 987, 991, 994, 998, 1002, 1005, 1009, 1012, 1016, 1019,
+	1023,
+};
+
+static const u16 xgamma10_37[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 5, 5, 5, 6, 6, 6,
+	6, 6, 6, 6, 6, 6, 6, 6, 7, 7, 7,
+	7, 7, 7, 7, 7, 7, 7, 8, 8, 8, 8,
+	8, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9,
+	9, 9, 9, 10, 10, 10, 10, 10, 10, 10, 10,
+	11, 11, 11, 11, 11, 11, 11, 11, 12, 12, 12,
+	12, 12, 12, 12, 13, 13, 13, 13, 13, 13, 14,
+	14, 14, 14, 14, 14, 15, 15, 15, 15, 15, 15,
+	16, 16, 16, 16, 16, 16, 17, 17, 17, 17, 17,
+	18, 18, 18, 18, 18, 19, 19, 19, 19, 19, 20,
+	20, 20, 20, 20, 21, 21, 21, 21, 21, 22, 22,
+	22, 22, 23, 23, 23, 23, 24, 24, 24, 24, 24,
+	25, 25, 25, 25, 26, 26, 26, 26, 27, 27, 27,
+	28, 28, 28, 28, 29, 29, 29, 29, 30, 30, 30,
+	31, 31, 31, 31, 32, 32, 32, 33, 33, 33, 33,
+	34, 34, 34, 35, 35, 35, 36, 36, 36, 37, 37,
+	37, 38, 38, 38, 39, 39, 39, 40, 40, 40, 41,
+	41, 41, 42, 42, 42, 43, 43, 44, 44, 44, 45,
+	45, 45, 46, 46, 47, 47, 47, 48, 48, 49, 49,
+	49, 50, 50, 51, 51, 51, 52, 52, 53, 53, 54,
+	54, 54, 55, 55, 56, 56, 57, 57, 58, 58, 58,
+	59, 59, 60, 60, 61, 61, 62, 62, 63, 63, 64,
+	64, 65, 65, 66, 66, 67, 67, 68, 68, 69, 69,
+	70, 70, 71, 71, 72, 72, 73, 73, 74, 75, 75,
+	76, 76, 77, 77, 78, 78, 79, 80, 80, 81, 81,
+	82, 82, 83, 84, 84, 85, 85, 86, 87, 87, 88,
+	89, 89, 90, 90, 91, 92, 92, 93, 94, 94, 95,
+	96, 96, 97, 98, 98, 99, 100, 100, 101, 102, 102,
+	103, 104, 104, 105, 106, 106, 107, 108, 109, 109, 110,
+	111, 112, 112, 113, 114, 114, 115, 116, 117, 118, 118,
+	119, 120, 121, 121, 122, 123, 124, 125, 125, 126, 127,
+	128, 129, 129, 130, 131, 132, 133, 134, 134, 135, 136,
+	137, 138, 139, 139, 140, 141, 142, 143, 144, 145, 146,
+	146, 147, 148, 149, 150, 151, 152, 153, 154, 155, 156,
+	157, 158, 158, 159, 160, 161, 162, 163, 164, 165, 166,
+	167, 168, 169, 170, 171, 172, 173, 174, 175, 176, 177,
+	178, 179, 180, 181, 182, 184, 185, 186, 187, 188, 189,
+	190, 191, 192, 193, 194, 195, 197, 198, 199, 200, 201,
+	202, 203, 204, 206, 207, 208, 209, 210, 211, 213, 214,
+	215, 216, 217, 218, 220, 221, 222, 223, 225, 226, 227,
+	228, 229, 231, 232, 233, 234, 236, 237, 238, 240, 241,
+	242, 243, 245, 246, 247, 249, 250, 251, 253, 254, 255,
+	257, 258, 259, 261, 262, 263, 265, 266, 268, 269, 270,
+	272, 273, 275, 276, 277, 279, 280, 282, 283, 285, 286,
+	288, 289, 291, 292, 294, 295, 297, 298, 300, 301, 303,
+	304, 306, 307, 309, 310, 312, 313, 315, 316, 318, 320,
+	321, 323, 324, 326, 328, 329, 331, 332, 334, 336, 337,
+	339, 341, 342, 344, 346, 347, 349, 351, 352, 354, 356,
+	358, 359, 361, 363, 364, 366, 368, 370, 372, 373, 375,
+	377, 379, 380, 382, 384, 386, 388, 389, 391, 393, 395,
+	397, 399, 401, 402, 404, 406, 408, 410, 412, 414, 416,
+	418, 420, 421, 423, 425, 427, 429, 431, 433, 435, 437,
+	439, 441, 443, 445, 447, 449, 451, 453, 455, 457, 459,
+	462, 464, 466, 468, 470, 472, 474, 476, 478, 480, 483,
+	485, 487, 489, 491, 493, 496, 498, 500, 502, 504, 507,
+	509, 511, 513, 515, 518, 520, 522, 524, 527, 529, 531,
+	534, 536, 538, 541, 543, 545, 548, 550, 552, 555, 557,
+	559, 562, 564, 567, 569, 571, 574, 576, 579, 581, 584,
+	586, 589, 591, 593, 596, 598, 601, 603, 606, 609, 611,
+	614, 616, 619, 621, 624, 626, 629, 632, 634, 637, 639,
+	642, 645, 647, 650, 653, 655, 658, 661, 663, 666, 669,
+	672, 674, 677, 680, 682, 685, 688, 691, 694, 696, 699,
+	702, 705, 708, 710, 713, 716, 719, 722, 725, 728, 730,
+	733, 736, 739, 742, 745, 748, 751, 754, 757, 760, 763,
+	766, 769, 772, 775, 778, 781, 784, 787, 790, 793, 796,
+	799, 802, 805, 809, 812, 815, 818, 821, 824, 827, 831,
+	834, 837, 840, 843, 847, 850, 853, 856, 860, 863, 866,
+	869, 873, 876, 879, 883, 886, 889, 893, 896, 899, 903,
+	906, 910, 913, 916, 920, 923, 927, 930, 934, 937, 940,
+	944, 947, 951, 954, 958, 961, 965, 969, 972, 976, 979,
+	983, 986, 990, 994, 997, 1001, 1005, 1008, 1012, 1016, 1019,
+	1023,
+};
+
+static const u16 xgamma10_38[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 5, 5, 6, 6, 6, 6, 6,
+	6, 6, 6, 6, 6, 6, 6, 7, 7, 7, 7,
+	7, 7, 7, 7, 7, 7, 8, 8, 8, 8, 8,
+	8, 8, 8, 8, 9, 9, 9, 9, 9, 9, 9,
+	9, 9, 10, 10, 10, 10, 10, 10, 10, 10, 11,
+	11, 11, 11, 11, 11, 11, 11, 12, 12, 12, 12,
+	12, 12, 13, 13, 13, 13, 13, 13, 13, 14, 14,
+	14, 14, 14, 14, 15, 15, 15, 15, 15, 15, 16,
+	16, 16, 16, 16, 16, 17, 17, 17, 17, 17, 18,
+	18, 18, 18, 18, 19, 19, 19, 19, 19, 20, 20,
+	20, 20, 20, 21, 21, 21, 21, 21, 22, 22, 22,
+	22, 23, 23, 23, 23, 24, 24, 24, 24, 24, 25,
+	25, 25, 25, 26, 26, 26, 26, 27, 27, 27, 28,
+	28, 28, 28, 29, 29, 29, 29, 30, 30, 30, 31,
+	31, 31, 31, 32, 32, 32, 33, 33, 33, 33, 34,
+	34, 34, 35, 35, 35, 36, 36, 36, 37, 37, 37,
+	38, 38, 38, 39, 39, 39, 40, 40, 40, 41, 41,
+	41, 42, 42, 43, 43, 43, 44, 44, 44, 45, 45,
+	46, 46, 46, 47, 47, 47, 48, 48, 49, 49, 49,
+	50, 50, 51, 51, 52, 52, 52, 53, 53, 54, 54,
+	55, 55, 55, 56, 56, 57, 57, 58, 58, 59, 59,
+	60, 60, 60, 61, 61, 62, 62, 63, 63, 64, 64,
+	65, 65, 66, 66, 67, 67, 68, 68, 69, 69, 70,
+	70, 71, 72, 72, 73, 73, 74, 74, 75, 75, 76,
+	76, 77, 78, 78, 79, 79, 80, 81, 81, 82, 82,
+	83, 83, 84, 85, 85, 86, 86, 87, 88, 88, 89,
+	90, 90, 91, 92, 92, 93, 93, 94, 95, 95, 96,
+	97, 97, 98, 99, 99, 100, 101, 102, 102, 103, 104,
+	104, 105, 106, 106, 107, 108, 109, 109, 110, 111, 112,
+	112, 113, 114, 115, 115, 116, 117, 118, 118, 119, 120,
+	121, 122, 122, 123, 124, 125, 126, 126, 127, 128, 129,
+	130, 130, 131, 132, 133, 134, 135, 136, 136, 137, 138,
+	139, 140, 141, 142, 143, 143, 144, 145, 146, 147, 148,
+	149, 150, 151, 152, 153, 153, 154, 155, 156, 157, 158,
+	159, 160, 161, 162, 163, 164, 165, 166, 167, 168, 169,
+	170, 171, 172, 173, 174, 175, 176, 177, 178, 179, 180,
+	182, 183, 184, 185, 186, 187, 188, 189, 190, 191, 192,
+	193, 195, 196, 197, 198, 199, 200, 201, 203, 204, 205,
+	206, 207, 208, 210, 211, 212, 213, 214, 216, 217, 218,
+	219, 220, 222, 223, 224, 225, 227, 228, 229, 230, 232,
+	233, 234, 235, 237, 238, 239, 241, 242, 243, 245, 246,
+	247, 249, 250, 251, 253, 254, 255, 257, 258, 259, 261,
+	262, 264, 265, 266, 268, 269, 271, 272, 274, 275, 276,
+	278, 279, 281, 282, 284, 285, 287, 288, 290, 291, 293,
+	294, 296, 297, 299, 300, 302, 303, 305, 307, 308, 310,
+	311, 313, 314, 316, 318, 319, 321, 323, 324, 326, 327,
+	329, 331, 332, 334, 336, 337, 339, 341, 342, 344, 346,
+	348, 349, 351, 353, 354, 356, 358, 360, 361, 363, 365,
+	367, 369, 370, 372, 374, 376, 378, 379, 381, 383, 385,
+	387, 389, 391, 392, 394, 396, 398, 400, 402, 404, 406,
+	408, 410, 412, 413, 415, 417, 419, 421, 423, 425, 427,
+	429, 431, 433, 435, 437, 439, 441, 443, 446, 448, 450,
+	452, 454, 456, 458, 460, 462, 464, 466, 469, 471, 473,
+	475, 477, 479, 482, 484, 486, 488, 490, 493, 495, 497,
+	499, 501, 504, 506, 508, 511, 513, 515, 517, 520, 522,
+	524, 527, 529, 531, 534, 536, 538, 541, 543, 546, 548,
+	550, 553, 555, 558, 560, 562, 565, 567, 570, 572, 575,
+	577, 580, 582, 585, 587, 590, 592, 595, 597, 600, 603,
+	605, 608, 610, 613, 616, 618, 621, 623, 626, 629, 631,
+	634, 637, 639, 642, 645, 648, 650, 653, 656, 658, 661,
+	664, 667, 669, 672, 675, 678, 681, 684, 686, 689, 692,
+	695, 698, 701, 703, 706, 709, 712, 715, 718, 721, 724,
+	727, 730, 733, 736, 739, 742, 745, 748, 751, 754, 757,
+	760, 763, 766, 769, 772, 775, 778, 781, 785, 788, 791,
+	794, 797, 800, 803, 807, 810, 813, 816, 820, 823, 826,
+	829, 832, 836, 839, 842, 846, 849, 852, 856, 859, 862,
+	866, 869, 872, 876, 879, 883, 886, 889, 893, 896, 900,
+	903, 907, 910, 914, 917, 921, 924, 928, 931, 935, 938,
+	942, 945, 949, 953, 956, 960, 964, 967, 971, 974, 978,
+	982, 986, 989, 993, 997, 1000, 1004, 1008, 1012, 1015, 1019,
+	1023,
+};
+
+static const u16 xgamma10_39[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	4, 4, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 5, 6, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 6, 6, 7, 7, 7, 7, 7, 7,
+	7, 7, 7, 7, 7, 8, 8, 8, 8, 8, 8,
+	8, 8, 8, 9, 9, 9, 9, 9, 9, 9, 9,
+	9, 10, 10, 10, 10, 10, 10, 10, 10, 11, 11,
+	11, 11, 11, 11, 11, 12, 12, 12, 12, 12, 12,
+	12, 13, 13, 13, 13, 13, 13, 13, 14, 14, 14,
+	14, 14, 14, 15, 15, 15, 15, 15, 15, 16, 16,
+	16, 16, 16, 16, 17, 17, 17, 17, 17, 18, 18,
+	18, 18, 18, 19, 19, 19, 19, 19, 20, 20, 20,
+	20, 20, 21, 21, 21, 21, 22, 22, 22, 22, 22,
+	23, 23, 23, 23, 24, 24, 24, 24, 25, 25, 25,
+	25, 26, 26, 26, 26, 27, 27, 27, 27, 28, 28,
+	28, 28, 29, 29, 29, 29, 30, 30, 30, 31, 31,
+	31, 31, 32, 32, 32, 33, 33, 33, 34, 34, 34,
+	35, 35, 35, 35, 36, 36, 36, 37, 37, 37, 38,
+	38, 38, 39, 39, 39, 40, 40, 41, 41, 41, 42,
+	42, 42, 43, 43, 43, 44, 44, 45, 45, 45, 46,
+	46, 46, 47, 47, 48, 48, 48, 49, 49, 50, 50,
+	51, 51, 51, 52, 52, 53, 53, 53, 54, 54, 55,
+	55, 56, 56, 57, 57, 57, 58, 58, 59, 59, 60,
+	60, 61, 61, 62, 62, 63, 63, 64, 64, 65, 65,
+	66, 66, 67, 67, 68, 68, 69, 69, 70, 70, 71,
+	71, 72, 73, 73, 74, 74, 75, 75, 76, 76, 77,
+	78, 78, 79, 79, 80, 80, 81, 82, 82, 83, 83,
+	84, 85, 85, 86, 87, 87, 88, 88, 89, 90, 90,
+	91, 92, 92, 93, 94, 94, 95, 96, 96, 97, 98,
+	98, 99, 100, 100, 101, 102, 102, 103, 104, 105, 105,
+	106, 107, 107, 108, 109, 110, 110, 111, 112, 113, 113,
+	114, 115, 116, 116, 117, 118, 119, 120, 120, 121, 122,
+	123, 124, 124, 125, 126, 127, 128, 129, 129, 130, 131,
+	132, 133, 134, 134, 135, 136, 137, 138, 139, 140, 141,
+	141, 142, 143, 144, 145, 146, 147, 148, 149, 150, 151,
+	152, 153, 153, 154, 155, 156, 157, 158, 159, 160, 161,
+	162, 163, 164, 165, 166, 167, 168, 169, 170, 171, 172,
+	173, 174, 176, 177, 178, 179, 180, 181, 182, 183, 184,
+	185, 186, 187, 188, 190, 191, 192, 193, 194, 195, 196,
+	198, 199, 200, 201, 202, 203, 204, 206, 207, 208, 209,
+	210, 212, 213, 214, 215, 217, 218, 219, 220, 221, 223,
+	224, 225, 227, 228, 229, 230, 232, 233, 234, 236, 237,
+	238, 239, 241, 242, 243, 245, 246, 248, 249, 250, 252,
+	253, 254, 256, 257, 259, 260, 261, 263, 264, 266, 267,
+	269, 270, 271, 273, 274, 276, 277, 279, 280, 282, 283,
+	285, 286, 288, 289, 291, 292, 294, 295, 297, 299, 300,
+	302, 303, 305, 306, 308, 310, 311, 313, 314, 316, 318,
+	319, 321, 323, 324, 326, 328, 329, 331, 333, 334, 336,
+	338, 340, 341, 343, 345, 346, 348, 350, 352, 353, 355,
+	357, 359, 361, 362, 364, 366, 368, 370, 372, 373, 375,
+	377, 379, 381, 383, 385, 386, 388, 390, 392, 394, 396,
+	398, 400, 402, 404, 406, 408, 410, 412, 414, 416, 418,
+	420, 422, 424, 426, 428, 430, 432, 434, 436, 438, 440,
+	442, 444, 446, 448, 451, 453, 455, 457, 459, 461, 463,
+	466, 468, 470, 472, 474, 477, 479, 481, 483, 485, 488,
+	490, 492, 494, 497, 499, 501, 504, 506, 508, 511, 513,
+	515, 518, 520, 522, 525, 527, 529, 532, 534, 537, 539,
+	541, 544, 546, 549, 551, 554, 556, 559, 561, 564, 566,
+	569, 571, 574, 576, 579, 581, 584, 586, 589, 592, 594,
+	597, 599, 602, 605, 607, 610, 613, 615, 618, 621, 623,
+	626, 629, 632, 634, 637, 640, 643, 645, 648, 651, 654,
+	656, 659, 662, 665, 668, 671, 673, 676, 679, 682, 685,
+	688, 691, 694, 697, 700, 702, 705, 708, 711, 714, 717,
+	720, 723, 726, 729, 732, 735, 739, 742, 745, 748, 751,
+	754, 757, 760, 763, 766, 770, 773, 776, 779, 782, 786,
+	789, 792, 795, 798, 802, 805, 808, 811, 815, 818, 821,
+	825, 828, 831, 835, 838, 841, 845, 848, 852, 855, 858,
+	862, 865, 869, 872, 876, 879, 883, 886, 890, 893, 897,
+	900, 904, 907, 911, 914, 918, 922, 925, 929, 933, 936,
+	940, 944, 947, 951, 955, 958, 962, 966, 969, 973, 977,
+	981, 985, 988, 992, 996, 1000, 1004, 1007, 1011, 1015, 1019,
+	1023,
+};
+
+static const u16 xgamma10_40[GAMMA10_TABLE_LENGTH] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
+	1, 1, 1, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+	2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3,
+	3, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4,
+	4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4,
+	5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	5, 5, 5, 6, 6, 6, 6, 6, 6, 6, 6,
+	6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 7,
+	7, 7, 7, 8, 8, 8, 8, 8, 8, 8, 8,
+	8, 9, 9, 9, 9, 9, 9, 9, 9, 9, 10,
+	10, 10, 10, 10, 10, 10, 10, 11, 11, 11, 11,
+	11, 11, 11, 11, 12, 12, 12, 12, 12, 12, 12,
+	13, 13, 13, 13, 13, 13, 14, 14, 14, 14, 14,
+	14, 15, 15, 15, 15, 15, 15, 16, 16, 16, 16,
+	16, 16, 17, 17, 17, 17, 17, 18, 18, 18, 18,
+	18, 18, 19, 19, 19, 19, 19, 20, 20, 20, 20,
+	21, 21, 21, 21, 21, 22, 22, 22, 22, 23, 23,
+	23, 23, 23, 24, 24, 24, 24, 25, 25, 25, 25,
+	26, 26, 26, 26, 27, 27, 27, 27, 28, 28, 28,
+	29, 29, 29, 29, 30, 30, 30, 30, 31, 31, 31,
+	32, 32, 32, 33, 33, 33, 33, 34, 34, 34, 35,
+	35, 35, 36, 36, 36, 37, 37, 37, 38, 38, 38,
+	39, 39, 39, 40, 40, 40, 41, 41, 41, 42, 42,
+	43, 43, 43, 44, 44, 44, 45, 45, 46, 46, 46,
+	47, 47, 48, 48, 48, 49, 49, 50, 50, 50, 51,
+	51, 52, 52, 53, 53, 53, 54, 54, 55, 55, 56,
+	56, 57, 57, 57, 58, 58, 59, 59, 60, 60, 61,
+	61, 62, 62, 63, 63, 64, 64, 65, 65, 66, 66,
+	67, 67, 68, 68, 69, 69, 70, 70, 71, 72, 72,
+	73, 73, 74, 74, 75, 75, 76, 77, 77, 78, 78,
+	79, 79, 80, 81, 81, 82, 82, 83, 84, 84, 85,
+	85, 86, 87, 87, 88, 89, 89, 90, 91, 91, 92,
+	93, 93, 94, 95, 95, 96, 97, 97, 98, 99, 99,
+	100, 101, 101, 102, 103, 104, 104, 105, 106, 106, 107,
+	108, 109, 109, 110, 111, 112, 112, 113, 114, 115, 116,
+	116, 117, 118, 119, 119, 120, 121, 122, 123, 123, 124,
+	125, 126, 127, 128, 128, 129, 130, 131, 132, 133, 134,
+	134, 135, 136, 137, 138, 139, 140, 141, 142, 143, 143,
+	144, 145, 146, 147, 148, 149, 150, 151, 152, 153, 154,
+	155, 156, 157, 158, 159, 160, 161, 162, 163, 164, 165,
+	166, 167, 168, 169, 170, 171, 172, 173, 174, 175, 176,
+	177, 178, 179, 180, 182, 183, 184, 185, 186, 187, 188,
+	189, 190, 192, 193, 194, 195, 196, 197, 199, 200, 201,
+	202, 203, 204, 206, 207, 208, 209, 210, 212, 213, 214,
+	215, 217, 218, 219, 220, 222, 223, 224, 226, 227, 228,
+	229, 231, 232, 233, 235, 236, 237, 239, 240, 241, 243,
+	244, 245, 247, 248, 250, 251, 252, 254, 255, 257, 258,
+	259, 261, 262, 264, 265, 267, 268, 270, 271, 273, 274,
+	276, 277, 279, 280, 282, 283, 285, 286, 288, 289, 291,
+	292, 294, 296, 297, 299, 300, 302, 304, 305, 307, 308,
+	310, 312, 313, 315, 317, 318, 320, 322, 323, 325, 327,
+	328, 330, 332, 333, 335, 337, 339, 340, 342, 344, 346,
+	348, 349, 351, 353, 355, 357, 358, 360, 362, 364, 366,
+	368, 369, 371, 373, 375, 377, 379, 381, 383, 385, 386,
+	388, 390, 392, 394, 396, 398, 400, 402, 404, 406, 408,
+	410, 412, 414, 416, 418, 420, 422, 424, 426, 429, 431,
+	433, 435, 437, 439, 441, 443, 445, 448, 450, 452, 454,
+	456, 458, 461, 463, 465, 467, 469, 472, 474, 476, 478,
+	481, 483, 485, 488, 490, 492, 495, 497, 499, 501, 504,
+	506, 509, 511, 513, 516, 518, 521, 523, 525, 528, 530,
+	533, 535, 538, 540, 543, 545, 548, 550, 553, 555, 558,
+	560, 563, 565, 568, 570, 573, 576, 578, 581, 583, 586,
+	589, 591, 594, 597, 599, 602, 605, 607, 610, 613, 616,
+	618, 621, 624, 627, 629, 632, 635, 638, 641, 643, 646,
+	649, 652, 655, 658, 660, 663, 666, 669, 672, 675, 678,
+	681, 684, 687, 690, 693, 696, 699, 702, 705, 708, 711,
+	714, 717, 720, 723, 726, 729, 732, 735, 739, 742, 745,
+	748, 751, 754, 758, 761, 764, 767, 770, 774, 777, 780,
+	783, 787, 790, 793, 797, 800, 803, 807, 810, 813, 817,
+	820, 824, 827, 830, 834, 837, 841, 844, 848, 851, 855,
+	858, 862, 865, 869, 872, 876, 879, 883, 886, 890, 894,
+	897, 901, 905, 908, 912, 916, 919, 923, 927, 930, 934,
+	938, 942, 945, 949, 953, 957, 960, 964, 968, 972, 976,
+	980, 984, 987, 991, 995, 999, 1003, 1007, 1011, 1015, 1019,
+	1023,
+};
+
+static const u16 *xgamma10_curves[GAMMA_CURVE_LENGTH] =  {
+	&xgamma10_01[0],
+	&xgamma10_02[0],
+	&xgamma10_03[0],
+	&xgamma10_04[0],
+	&xgamma10_05[0],
+	&xgamma10_06[0],
+	&xgamma10_07[0],
+	&xgamma10_08[0],
+	&xgamma10_09[0],
+	&xgamma10_10[0],
+	&xgamma10_11[0],
+	&xgamma10_12[0],
+	&xgamma10_13[0],
+	&xgamma10_14[0],
+	&xgamma10_15[0],
+	&xgamma10_16[0],
+	&xgamma10_17[0],
+	&xgamma10_18[0],
+	&xgamma10_19[0],
+	&xgamma10_20[0],
+	&xgamma10_21[0],
+	&xgamma10_22[0],
+	&xgamma10_23[0],
+	&xgamma10_24[0],
+	&xgamma10_25[0],
+	&xgamma10_26[0],
+	&xgamma10_27[0],
+	&xgamma10_28[0],
+	&xgamma10_29[0],
+	&xgamma10_30[0],
+	&xgamma10_31[0],
+	&xgamma10_32[0],
+	&xgamma10_33[0],
+	&xgamma10_34[0],
+	&xgamma10_35[0],
+	&xgamma10_36[0],
+	&xgamma10_37[0],
+	&xgamma10_38[0],
+	&xgamma10_39[0],
+	&xgamma10_40[0],
+};
+#endif /* __XILINX_GAMMA_COEFF_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-gamma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-gamma.c
@@ -0,0 +1,565 @@
+/*
+ * Xilinx Gamma Correction IP
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/xilinx-v4l2-controls.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-gamma-coeff.h"
+#include "xilinx-vip.h"
+
+#define XGAMMA_MIN_HEIGHT	(64)
+#define XGAMMA_MAX_HEIGHT	(4320)
+#define XGAMMA_DEF_HEIGHT	(720)
+#define XGAMMA_MIN_WIDTH	(64)
+#define XGAMMA_MAX_WIDTH	(8192)
+#define XGAMMA_DEF_WIDTH	(1280)
+
+#define XGAMMA_AP_CTRL			(0x0000)
+#define XGAMMA_GIE			(0x0004)
+#define XGAMMA_IER			(0x0008)
+#define XGAMMA_ISR			(0x000c)
+#define XGAMMA_WIDTH			(0x0010)
+#define XGAMMA_HEIGHT			(0x0018)
+#define XGAMMA_VIDEO_FORMAT		(0x0020)
+#define XGAMMA_GAMMA_LUT_0_BASE		(0x0800)
+#define XGAMMA_GAMMA_LUT_1_BASE		(0x1000)
+#define XGAMMA_GAMMA_LUT_2_BASE		(0x1800)
+
+#define XGAMMA_RESET_DEASSERT	(0)
+#define XGAMMA_RESET_ASSERT	(1)
+#define XGAMMA_START		BIT(0)
+#define XGAMMA_AUTO_RESTART	BIT(7)
+#define XGAMMA_STREAM_ON	(XGAMMA_START | XGAMMA_AUTO_RESTART)
+
+enum xgamma_video_format {
+	XGAMMA_RGB = 0,
+};
+
+/**
+ * struct xgamma_dev - Xilinx Video Gamma LUT device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: Scaler sub-device media pads
+ * @formats: V4L2 media bus formats at the sink and source pads
+ * @default_formats: default V4L2 media bus formats
+ * @ctrl_handler: V4L2 Control Handler for R,G,B Gamma Controls
+ * @red_lut: Pointer to the gamma coefficient as per the Red Gamma control
+ * @green_lut: Pointer to the gamma coefficient as per the Green Gamma control
+ * @blue_lut: Pointer to the gamma coefficient as per the Blue Gamma control
+ * @color_depth: Color depth of the Video Gamma IP
+ * @gamma_table: Pointer to the table containing various gamma values
+ * @rst_gpio: GPIO reset line to bring VPSS Scaler out of reset
+ * @max_width: Maximum width supported by this instance.
+ * @max_height: Maximum height supported by this instance.
+ */
+struct xgamma_dev {
+	struct xvip_device xvip;
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	const u16 *red_lut;
+	const u16 *green_lut;
+	const u16 *blue_lut;
+	u32 color_depth;
+	const u16 **gamma_table;
+	struct gpio_desc *rst_gpio;
+	u32 max_width;
+	u32 max_height;
+};
+
+static inline u32 xg_read(struct xgamma_dev *xg, u32 reg)
+{
+	u32 data;
+
+	data = xvip_read(&xg->xvip, reg);
+	dev_dbg(xg->xvip.dev,
+		"Reading 0x%x from reg offset 0x%x", data, reg);
+	return data;
+}
+
+static inline void xg_write(struct xgamma_dev *xg, u32 reg, u32 data)
+{
+	dev_dbg(xg->xvip.dev,
+		"Writing 0x%x to reg offset 0x%x", data, reg);
+	xvip_write(&xg->xvip, reg, data);
+#ifdef DEBUG
+	if (xg_read(xg, reg) != data)
+		dev_err(xg->xvip.dev,
+			"Write 0x%x does not match read back", data);
+#endif
+}
+
+static inline struct xgamma_dev *to_xg(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xgamma_dev, xvip.subdev);
+}
+
+static struct v4l2_mbus_framefmt *
+__xg_get_pad_format(struct xgamma_dev *xg,
+		    struct v4l2_subdev_state *sd_state,
+		    unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xg->xvip.subdev, sd_state,
+						    pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xg->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static void xg_set_lut_entries(struct xgamma_dev *xg,
+			       const u16 *lut, const u32 lut_base)
+{
+	int itr;
+	u32 lut_offset, lut_data;
+
+	lut_offset = lut_base;
+	/* Write LUT Entries */
+	for (itr = 0; itr < BIT(xg->color_depth - 1); itr++) {
+		lut_data = (lut[2 * itr + 1] << 16) | lut[2 * itr];
+		xg_write(xg, lut_offset, lut_data);
+		lut_offset += 4;
+	}
+}
+
+static int xg_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xgamma_dev *xg = to_xg(subdev);
+
+	if (!enable) {
+		dev_dbg(xg->xvip.dev, "%s : Off", __func__);
+		gpiod_set_value_cansleep(xg->rst_gpio, XGAMMA_RESET_ASSERT);
+		gpiod_set_value_cansleep(xg->rst_gpio, XGAMMA_RESET_DEASSERT);
+		return 0;
+	}
+	dev_dbg(xg->xvip.dev, "%s : Started", __func__);
+
+	dev_dbg(xg->xvip.dev, "%s : Setting width %d and height %d",
+		__func__, xg->formats[XVIP_PAD_SINK].width,
+		xg->formats[XVIP_PAD_SINK].height);
+	xg_write(xg, XGAMMA_WIDTH, xg->formats[XVIP_PAD_SINK].width);
+	xg_write(xg, XGAMMA_HEIGHT, xg->formats[XVIP_PAD_SINK].height);
+	xg_write(xg, XGAMMA_VIDEO_FORMAT, XGAMMA_RGB);
+	xg_set_lut_entries(xg, xg->red_lut, XGAMMA_GAMMA_LUT_0_BASE);
+	xg_set_lut_entries(xg, xg->green_lut, XGAMMA_GAMMA_LUT_1_BASE);
+	xg_set_lut_entries(xg, xg->blue_lut, XGAMMA_GAMMA_LUT_2_BASE);
+
+	/* Start GAMMA Correction LUT Video IP */
+	xg_write(xg, XGAMMA_AP_CTRL, XGAMMA_STREAM_ON);
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops xg_video_ops = {
+	.s_stream = xg_s_stream,
+};
+
+static int xg_get_format(struct v4l2_subdev *subdev,
+			 struct v4l2_subdev_state *sd_state,
+			 struct v4l2_subdev_format *fmt)
+{
+	struct xgamma_dev *xg = to_xg(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xg_get_pad_format(xg, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xg_set_format(struct v4l2_subdev *subdev,
+			 struct v4l2_subdev_state *sd_state,
+			 struct v4l2_subdev_format *fmt)
+{
+	struct xgamma_dev *xg = to_xg(subdev);
+	struct v4l2_mbus_framefmt *__format;
+
+	__format = __xg_get_pad_format(xg, sd_state, fmt->pad, fmt->which);
+	if (!__format)
+		return -EINVAL;
+
+	*__format = fmt->format;
+
+	if (fmt->pad == XVIP_PAD_SINK) {
+		if (__format->code != MEDIA_BUS_FMT_RBG888_1X24) {
+			dev_dbg(xg->xvip.dev,
+				"Unsupported sink media bus code format");
+			__format->code = MEDIA_BUS_FMT_RBG888_1X24;
+		}
+	}
+	__format->width = clamp_t(unsigned int, fmt->format.width,
+				  XGAMMA_MIN_WIDTH, xg->max_width);
+	__format->height = clamp_t(unsigned int, fmt->format.height,
+				   XGAMMA_MIN_HEIGHT, xg->max_height);
+
+	fmt->format = *__format;
+	/* Propagate to Source Pad */
+	__format = __xg_get_pad_format(xg, sd_state, XVIP_PAD_SOURCE,
+				       fmt->which);
+	if (!__format)
+		return -EINVAL;
+
+	*__format = fmt->format;
+	return 0;
+}
+
+static int xg_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xgamma_dev *xg = to_xg(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xg->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xg->default_formats[XVIP_PAD_SOURCE];
+	return 0;
+}
+
+static int xg_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static const struct v4l2_subdev_internal_ops xg_internal_ops = {
+	.open = xg_open,
+	.close = xg_close,
+};
+
+static const struct v4l2_subdev_pad_ops xg_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xg_get_format,
+	.set_fmt = xg_set_format,
+};
+
+static const struct v4l2_subdev_ops xg_ops = {
+	.video = &xg_video_ops,
+	.pad = &xg_pad_ops,
+};
+
+static int
+select_gamma(s32 value, const u16 **coeff, const u16 **xgamma_curves)
+{
+	if (!coeff)
+		return -EINVAL;
+	if (value <= 0 || value > GAMMA_CURVE_LENGTH)
+		return -EINVAL;
+
+	*coeff = *(xgamma_curves + value - 1);
+	return 0;
+}
+
+static int xg_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	int rval;
+	struct xgamma_dev *xg =
+		container_of(ctrl->handler,
+			     struct xgamma_dev, ctrl_handler);
+	dev_dbg(xg->xvip.dev, "%s called", __func__);
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_GAMMA_CORR_RED_GAMMA:
+		rval = select_gamma(ctrl->val, &xg->red_lut, xg->gamma_table);
+		if (rval < 0) {
+			dev_err(xg->xvip.dev, "Invalid Red Gamma");
+			return rval;
+		}
+		dev_dbg(xg->xvip.dev, "%s: Setting Red Gamma to %d.%d",
+			__func__, ctrl->val / 10, ctrl->val % 10);
+		xg_set_lut_entries(xg, xg->red_lut, XGAMMA_GAMMA_LUT_0_BASE);
+		break;
+	case V4L2_CID_XILINX_GAMMA_CORR_BLUE_GAMMA:
+		rval = select_gamma(ctrl->val, &xg->blue_lut, xg->gamma_table);
+		if (rval < 0) {
+			dev_err(xg->xvip.dev, "Invalid Blue Gamma");
+			return rval;
+		}
+		dev_dbg(xg->xvip.dev, "%s: Setting Blue Gamma to %d.%d",
+			__func__, ctrl->val / 10, ctrl->val % 10);
+		xg_set_lut_entries(xg, xg->blue_lut, XGAMMA_GAMMA_LUT_1_BASE);
+		break;
+	case V4L2_CID_XILINX_GAMMA_CORR_GREEN_GAMMA:
+		rval = select_gamma(ctrl->val, &xg->green_lut, xg->gamma_table);
+		if (rval < 0) {
+			dev_err(xg->xvip.dev, "Invalid Green Gamma");
+			return -EINVAL;
+		}
+		dev_dbg(xg->xvip.dev, "%s: Setting Green Gamma to %d.%d",
+			__func__, ctrl->val / 10, ctrl->val % 10);
+		xg_set_lut_entries(xg, xg->green_lut, XGAMMA_GAMMA_LUT_2_BASE);
+		break;
+	}
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops xg_ctrl_ops = {
+	.s_ctrl = xg_s_ctrl,
+};
+
+static struct v4l2_ctrl_config xg_ctrls[] = {
+	/* Red Gamma */
+	{
+		.ops = &xg_ctrl_ops,
+		.id = V4L2_CID_XILINX_GAMMA_CORR_RED_GAMMA,
+		.name = "Red Gamma Correction|1->0.1|10->1.0",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 1,
+		.max = 40,
+		.step = 1,
+		.def = 10,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+	/* Blue Gamma */
+	{
+		.ops = &xg_ctrl_ops,
+		.id = V4L2_CID_XILINX_GAMMA_CORR_BLUE_GAMMA,
+		.name = "Blue Gamma Correction|1->0.1|10->1.0",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 1,
+		.max = 40,
+		.step = 1,
+		.def = 10,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+	/* Green Gamma */
+	{
+		.ops = &xg_ctrl_ops,
+		.id = V4L2_CID_XILINX_GAMMA_CORR_GREEN_GAMMA,
+		.name = "Green Gamma Correction|1->0.1|10->1.0)",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 1,
+		.max = 40,
+		.step = 1,
+		.def = 10,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+};
+
+static const struct media_entity_operations xg_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static int xg_parse_of(struct xgamma_dev *xg)
+{
+	struct device *dev = xg->xvip.dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id = 0;
+	int rval;
+
+	rval = of_property_read_u32(node, "xlnx,max-height", &xg->max_height);
+	if (rval < 0) {
+		dev_err(dev, "xlnx,max-height is missing!");
+		return -EINVAL;
+	} else if (xg->max_height > XGAMMA_MAX_HEIGHT ||
+		   xg->max_height < XGAMMA_MIN_HEIGHT) {
+		dev_err(dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	rval = of_property_read_u32(node, "xlnx,max-width", &xg->max_width);
+	if (rval < 0) {
+		dev_err(dev, "xlnx,max-width is missing!");
+		return -EINVAL;
+	} else if (xg->max_width > XGAMMA_MAX_WIDTH ||
+		   xg->max_width < XGAMMA_MIN_WIDTH) {
+		dev_err(dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			rval = of_property_read_u32(port, "reg", &port_id);
+			if (rval < 0) {
+				dev_err(dev, "No reg in DT");
+				return rval;
+			}
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "Invalid reg in DT");
+				return -EINVAL;
+			}
+
+			rval = of_property_read_u32(port, "xlnx,video-width",
+						    &xg->color_depth);
+			if (rval < 0) {
+				dev_err(dev, "Missing xlnx-video-width in DT");
+				return rval;
+			}
+			switch (xg->color_depth) {
+			case GAMMA_BPC_8:
+				xg->gamma_table = xgamma8_curves;
+				break;
+			case GAMMA_BPC_10:
+				xg->gamma_table = xgamma10_curves;
+				break;
+			default:
+				dev_err(dev, "Unsupported color depth %d",
+					xg->color_depth);
+				return -EINVAL;
+			}
+		}
+	}
+
+	xg->rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(xg->rst_gpio)) {
+		if (PTR_ERR(xg->rst_gpio) != -EPROBE_DEFER)
+			dev_err(dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(xg->rst_gpio);
+	}
+	return 0;
+}
+
+static int xg_probe(struct platform_device *pdev)
+{
+	struct xgamma_dev *xg;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *def_fmt;
+	int rval, itr;
+
+	dev_dbg(&pdev->dev, "Gamma LUT Probe Started");
+	xg = devm_kzalloc(&pdev->dev, sizeof(*xg), GFP_KERNEL);
+	if (!xg)
+		return -ENOMEM;
+	xg->xvip.dev = &pdev->dev;
+	rval = xg_parse_of(xg);
+	if (rval < 0)
+		return rval;
+	rval = xvip_init_resources(&xg->xvip);
+	if (rval)
+		return -EIO;
+
+	dev_dbg(xg->xvip.dev, "Reset Xilinx Video Gamma Corrrection");
+	gpiod_set_value_cansleep(xg->rst_gpio, XGAMMA_RESET_DEASSERT);
+
+	/* Init V4L2 subdev */
+	subdev = &xg->xvip.subdev;
+	v4l2_subdev_init(subdev, &xg_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xg_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Default Formats Initialization */
+	def_fmt = &xg->default_formats[XVIP_PAD_SINK];
+	/* GAMMA LUT IP only to be supported for RGB */
+	def_fmt->code = MEDIA_BUS_FMT_RBG888_1X24;
+	def_fmt->field = V4L2_FIELD_NONE;
+	def_fmt->colorspace = V4L2_COLORSPACE_SRGB;
+	def_fmt->width = XGAMMA_DEF_WIDTH;
+	def_fmt->height = XGAMMA_DEF_HEIGHT;
+	xg->formats[XVIP_PAD_SINK] = *def_fmt;
+
+	def_fmt = &xg->default_formats[XVIP_PAD_SOURCE];
+	*def_fmt = xg->default_formats[XVIP_PAD_SINK];
+	xg->formats[XVIP_PAD_SOURCE] = *def_fmt;
+
+	xg->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xg->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Init Media Entity */
+	subdev->entity.ops = &xg_media_ops;
+	rval = media_entity_pads_init(&subdev->entity, 2, xg->pads);
+	if (rval < 0)
+		goto media_error;
+
+	/* V4L2 Controls */
+	v4l2_ctrl_handler_init(&xg->ctrl_handler, ARRAY_SIZE(xg_ctrls));
+	for (itr = 0; itr < ARRAY_SIZE(xg_ctrls); itr++) {
+		v4l2_ctrl_new_custom(&xg->ctrl_handler,
+				     &xg_ctrls[itr], NULL);
+	}
+	if (xg->ctrl_handler.error) {
+		dev_err(&pdev->dev, "Failed to add V4L2 controls");
+		rval = xg->ctrl_handler.error;
+		goto ctrl_error;
+	}
+	subdev->ctrl_handler = &xg->ctrl_handler;
+	rval = v4l2_ctrl_handler_setup(&xg->ctrl_handler);
+	if (rval < 0) {
+		dev_err(&pdev->dev, "Failed to setup control handler");
+		goto  ctrl_error;
+	}
+
+	platform_set_drvdata(pdev, xg);
+	rval = v4l2_async_register_subdev(subdev);
+	if (rval < 0) {
+		dev_err(&pdev->dev, "failed to register subdev");
+		goto v4l2_subdev_error;
+	}
+	dev_info(&pdev->dev,
+		 "Xilinx %d-bit Video Gamma Correction LUT registered",
+		 xg->color_depth);
+	return 0;
+ctrl_error:
+	v4l2_ctrl_handler_free(&xg->ctrl_handler);
+v4l2_subdev_error:
+	media_entity_cleanup(&subdev->entity);
+media_error:
+	xvip_cleanup_resources(&xg->xvip);
+	return rval;
+}
+
+static int xg_remove(struct platform_device *pdev)
+{
+	struct xgamma_dev *xg = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xg->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	/* Add entry to cleanup v4l2 control handle */
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xg->xvip);
+	return 0;
+}
+
+static const struct of_device_id xg_of_id_table[] = {
+	{.compatible = "xlnx,v-gamma-lut"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xg_of_id_table);
+
+static struct platform_driver xg_driver = {
+	.driver = {
+		.name = "xilinx-gamma-lut",
+		.of_match_table = xg_of_id_table,
+	},
+	.probe = xg_probe,
+	.remove = xg_remove,
+};
+
+module_platform_driver(xg_driver);
+MODULE_DESCRIPTION("Xilinx Video Gamma Correction LUT Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-hdmirx-hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-hdmirx-hw.h
@@ -0,0 +1,729 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx HDMI 2.1 Rx Subsystem register map
+ *
+ * Copyright (c) 2021 Xilinx
+ * Author: Vishal Sagar <vishal.sagar@xilinx.com>
+ */
+
+#ifndef __XILINX_HDMIRX_HW_H__
+#define __XILINX_HDMIRX_HW_H__
+
+#include <linux/bits.h>
+#include <linux/io.h>
+
+/* VER (Version Interface) peripheral register offsets */
+#define HDMIRX_VER_BASE				0x0
+/* VER Identification */
+#define HDMIRX_VER_ID_OFFSET			((HDMIRX_VER_BASE) + (0 * 4))
+/* VER Version */
+#define HDMIRX_VER_VERSION_OFFSET		((HDMIRX_VER_BASE) + (1 * 4))
+/* VCKE System Counts */
+#define HDMIRX_VER_VCKE_SYS_CNT_OFFSET		((HDMIRX_VER_BASE) + (2 * 4))
+/* SR/SSB period error 0 counter */
+#define HDMIRX_VER_SR_SSB_ERR_CNT0_OFFSET	((HDMIRX_VER_BASE) + (3 * 4))
+/* SR/SSB period error 1 counter */
+#define HDMIRX_VER_SR_SSB_ERR_CNT1_OFFSET	((HDMIRX_VER_BASE) + (4 * 4))
+/* SR/SSB period error 2 counter */
+#define HDMIRX_VER_SR_SSB_ERR_CNT2_OFFSET	((HDMIRX_VER_BASE) + (5 * 4))
+/* SR/SSB period error 3 counter */
+#define HDMIRX_VER_SR_SSB_ERR_CNT3_OFFSET	((HDMIRX_VER_BASE) + (6 * 4))
+/* FRL word aligner tap select changed */
+#define HDMIRX_VER_DBG_STA_OFFSET		((HDMIRX_VER_BASE) + (7 * 4))
+/* FRL Map error */
+#define HDMIRX_VER_FRL_MAP_ERR_OFFSET		((HDMIRX_VER_BASE) + (8 * 4))
+
+/* PIO (Parallel Interface) peripheral register offsets */
+#define HDMIRX_PIO_BASE				(1 * 64)
+/* PIO Identification */
+#define HDMIRX_PIO_ID_OFFSET			((HDMIRX_PIO_BASE) + (0 * 4))
+/* PIO Control */
+#define HDMIRX_PIO_CTRL_OFFSET			((HDMIRX_PIO_BASE) + (1 * 4))
+/* PIO Control Set */
+#define HDMIRX_PIO_CTRL_SET_OFFSET		((HDMIRX_PIO_BASE) + (2 * 4))
+/* PIO Control Clear */
+#define HDMIRX_PIO_CTRL_CLR_OFFSET		((HDMIRX_PIO_BASE) + (3 * 4))
+/* PIO Status */
+#define HDMIRX_PIO_STA_OFFSET			((HDMIRX_PIO_BASE) + (4 * 4))
+/* PIO Out */
+#define HDMIRX_PIO_OUT_OFFSET			((HDMIRX_PIO_BASE) + (5 * 4))
+/* PIO Out Set */
+#define HDMIRX_PIO_OUT_SET_OFFSET		((HDMIRX_PIO_BASE) + (6 * 4))
+/* PIO Out Clear */
+#define HDMIRX_PIO_OUT_CLR_OFFSET		((HDMIRX_PIO_BASE) + (7 * 4))
+/* PIO Out Mask */
+#define HDMIRX_PIO_OUT_MSK_OFFSET		((HDMIRX_PIO_BASE) + (8 * 4))
+/* PIO In */
+#define HDMIRX_PIO_IN_OFFSET			((HDMIRX_PIO_BASE) + (9 * 4))
+/* PIO In Event */
+#define HDMIRX_PIO_IN_EVT_OFFSET		((HDMIRX_PIO_BASE) + (10 * 4))
+/* PIO In Event Rising Edge */
+#define HDMIRX_PIO_IN_EVT_RE_OFFSET		((HDMIRX_PIO_BASE) + (11 * 4))
+/* PIO In Event Falling Edge */
+#define HDMIRX_PIO_IN_EVT_FE_OFFSET		((HDMIRX_PIO_BASE) + (12 * 4))
+
+/* Timer peripheral register offsets */
+#define HDMIRX_TMR_BASE				(2 * 64)
+/* TMR Identification */
+#define HDMIRX_TMR_ID_OFFSET			((HDMIRX_TMR_BASE) + (0 * 4))
+/* TMR Control */
+#define HDMIRX_TMR_CTRL_OFFSET			((HDMIRX_TMR_BASE) + (1 * 4))
+/* TMR Control Register Set offset */
+#define HDMIRX_TMR_CTRL_SET_OFFSET		((HDMIRX_TMR_BASE) + (2 * 4))
+/* TMR Control Register Clear offset */
+#define HDMIRX_TMR_CTRL_CLR_OFFSET		((HDMIRX_TMR_BASE) + (3 * 4))
+/* TMR Status */
+#define HDMIRX_TMR_STA_OFFSET			((HDMIRX_TMR_BASE) + (4 * 4))
+/* TMR Counter */
+#define HDMIRX_TMR_1_CNT_OFFSET			((HDMIRX_TMR_BASE) + (5 * 4))
+/* TMR Counter */
+#define HDMIRX_TMR_2_CNT_OFFSET			((HDMIRX_TMR_BASE) + (6 * 4))
+/* TMR Counter */
+#define HDMIRX_TMR_3_CNT_OFFSET			((HDMIRX_TMR_BASE) + (7 * 4))
+/* TMR Counter */
+#define HDMIRX_TMR_4_CNT_OFFSET			((HDMIRX_TMR_BASE) + (8 * 4))
+
+/* Video Timing Detector (VTD) peripheral register offsets */
+#define HDMIRX_VTD_BASE				(3 * 64)
+/* VTD Identification */
+#define HDMIRX_VTD_ID_OFFSET			((HDMIRX_VTD_BASE) + (0 * 4))
+/* VTD Control */
+#define HDMIRX_VTD_CTRL_OFFSET			((HDMIRX_VTD_BASE) + (1 * 4))
+/* VTD Control Set */
+#define HDMIRX_VTD_CTRL_SET_OFFSET		((HDMIRX_VTD_BASE) + (2 * 4))
+/* VTD Control Clear */
+#define HDMIRX_VTD_CTRL_CLR_OFFSET		((HDMIRX_VTD_BASE) + (3 * 4))
+/* VTD Status */
+#define HDMIRX_VTD_STA_OFFSET			((HDMIRX_VTD_BASE) + (4 * 4))
+/* VTD Total Pixels */
+#define HDMIRX_VTD_TOT_PIX_OFFSET		((HDMIRX_VTD_BASE) + (5 * 4))
+/* VTD Active Pixels */
+#define HDMIRX_VTD_ACT_PIX_OFFSET		((HDMIRX_VTD_BASE) + (6 * 4))
+/* VTD Total Lines */
+#define HDMIRX_VTD_TOT_LIN_OFFSET		((HDMIRX_VTD_BASE) + (7 * 4))
+/* VTD Active Lines */
+#define HDMIRX_VTD_ACT_LIN_OFFSET		((HDMIRX_VTD_BASE) + (8 * 4))
+/* VTD Vertical Sync Width */
+#define HDMIRX_VTD_VSW_OFFSET			((HDMIRX_VTD_BASE) + (9 * 4))
+/* VTD Horizontal Sync Width */
+#define HDMIRX_VTD_HSW_OFFSET			((HDMIRX_VTD_BASE) + (10 * 4))
+/* VTD Vertical Front Porch */
+#define HDMIRX_VTD_VFP_OFFSET			((HDMIRX_VTD_BASE) + (11 * 4))
+/* VTD Vertical Back Porch */
+#define HDMIRX_VTD_VBP_OFFSET			((HDMIRX_VTD_BASE) + (12 * 4))
+/* VTD Horizontal Front Porch */
+#define HDMIRX_VTD_HFP_OFFSET			((HDMIRX_VTD_BASE) + (13 * 4))
+/* VTD Horizontal Back Porch */
+#define HDMIRX_VTD_HBP_OFFSET			((HDMIRX_VTD_BASE) + (14 * 4))
+
+/* DDC (Display Data Channel) peripheral register offsets */
+#define HDMIRX_DDC_BASE				(4 * 64)
+/* DDC Identification */
+#define HDMIRX_DDC_ID_OFFSET			((HDMIRX_DDC_BASE) + (0 * 4))
+/* DDC Control */
+#define HDMIRX_DDC_CTRL_OFFSET			((HDMIRX_DDC_BASE) + (1 * 4))
+/* DDC Control Register Set offset */
+#define HDMIRX_DDC_CTRL_SET_OFFSET		((HDMIRX_DDC_BASE) + (2 * 4))
+/* DDC Control Register Clear offset */
+#define HDMIRX_DDC_CTRL_CLR_OFFSET		((HDMIRX_DDC_BASE) + (3 * 4))
+/* DDC Status */
+#define HDMIRX_DDC_STA_OFFSET			((HDMIRX_DDC_BASE) + (4 * 4))
+/* DDC EDID Status */
+#define HDMIRX_DDC_EDID_STA_OFFSET		((HDMIRX_DDC_BASE) + (5 * 4))
+/* DDC HDCP Status */
+#define HDMIRX_DDC_HDCP_STA_OFFSET		((HDMIRX_DDC_BASE) + (6 * 4))
+/* DDC Read EDID segment pointer offset */
+#define HDMIRX_DDC_EDID_SP_OFFSET		((HDMIRX_DDC_BASE) + (8 * 4))
+/* DDC Read EDID write pointer offset */
+#define HDMIRX_DDC_EDID_WP_OFFSET		((HDMIRX_DDC_BASE) + (9 * 4))
+/* DDC Read EDID read pointer offset */
+#define HDMIRX_DDC_EDID_RP_OFFSET		((HDMIRX_DDC_BASE) + (10 * 4))
+/* DDC Read EDID data offset */
+#define HDMIRX_DDC_EDID_DATA_OFFSET		((HDMIRX_DDC_BASE) + (11 * 4))
+/* DDC Read HDCP address offset */
+#define HDMIRX_DDC_HDCP_ADDRESS_OFFSET		((HDMIRX_DDC_BASE) + (12 * 4))
+/* DDC Read HDCP data offset */
+#define HDMIRX_DDC_HDCP_DATA_OFFSET		((HDMIRX_DDC_BASE) + (13 * 4))
+
+/* Auxiliary (AUX) peripheral register offsets */
+#define HDMIRX_AUX_BASE				(5 * 64)
+/* AUX Identification */
+#define HDMIRX_AUX_ID_OFFSET			((HDMIRX_AUX_BASE) + (0 * 4))
+/* AUX Control */
+#define HDMIRX_AUX_CTRL_OFFSET			((HDMIRX_AUX_BASE) + (1 * 4))
+/* AUX Control Register Set offset */
+#define HDMIRX_AUX_CTRL_SET_OFFSET		((HDMIRX_AUX_BASE) + (2 * 4))
+/* AUX Control Register Clear offset */
+#define HDMIRX_AUX_CTRL_CLR_OFFSET		((HDMIRX_AUX_BASE) + (3 * 4))
+/* AUX Status */
+#define HDMIRX_AUX_STA_OFFSET			((HDMIRX_AUX_BASE) + (4 * 4))
+/* AUX Data */
+#define HDMIRX_AUX_DAT_OFFSET			((HDMIRX_AUX_BASE) + (5 * 4))
+/* AUX Flush Count */
+#define HDMIRX_AUX_FLUSH_CNT_OFFSET		((HDMIRX_AUX_BASE) + (6 * 4))
+
+/* Audio (AUD) peripheral register offsets */
+#define HDMIRX_AUD_BASE				(6 * 64)
+/* AUD Identification */
+#define HDMIRX_AUD_ID_OFFSET			((HDMIRX_AUD_BASE) + (0 * 4))
+/* AUD Control */
+#define HDMIRX_AUD_CTRL_OFFSET			((HDMIRX_AUD_BASE) + (1 * 4))
+/* AUD Control Register Set offset */
+#define HDMIRX_AUD_CTRL_SET_OFFSET		((HDMIRX_AUD_BASE) + (2 * 4))
+/* AUD Control Register Clear offset */
+#define HDMIRX_AUD_CTRL_CLR_OFFSET		((HDMIRX_AUD_BASE) + (3 * 4))
+/* AUD Status */
+#define HDMIRX_AUD_STA_OFFSET			((HDMIRX_AUD_BASE) + (4 * 4))
+/* AUD CTS */
+#define HDMIRX_AUD_CTS_OFFSET			((HDMIRX_AUD_BASE) + (5 * 4))
+/* AUD N */
+#define HDMIRX_AUD_N_OFFSET			((HDMIRX_AUD_BASE) + (6 * 4))
+/* AUD Flush Count */
+#define HDMIRX_AUD_FLUSH_CNT_OFFSET		((HDMIRX_AUD_BASE) + (7 * 4))
+
+/* Link Status (LNKSTA) peripheral register offsets */
+#define HDMIRX_LNKSTA_BASE			(7 * 64)
+/* LNKSTA Identification */
+#define HDMIRX_LNKSTA_ID_OFFSET			((HDMIRX_LNKSTA_BASE) + (0 * 4))
+/* LNKSTA Control */
+#define HDMIRX_LNKSTA_CTRL_OFFSET		((HDMIRX_LNKSTA_BASE) + (1 * 4))
+/* LNKSTA Control Register Set offset */
+#define HDMIRX_LNKSTA_CTRL_SET_OFFSET		((HDMIRX_LNKSTA_BASE) + (2 * 4))
+/* LNKSTA Control Register Clear offset */
+#define HDMIRX_LNKSTA_CTRL_CLR_OFFSET		((HDMIRX_LNKSTA_BASE) + (3 * 4))
+/* LNKSTA Status */
+#define HDMIRX_LNKSTA_STA_OFFSET		((HDMIRX_LNKSTA_BASE) + (4 * 4))
+/* LNKSTA Link Error Counter Channel 0 */
+#define HDMIRX_LNKSTA_LNK_ERR0_OFFSET		((HDMIRX_LNKSTA_BASE) + (5 * 4))
+/* LNKSTA Link Error Counter Channel 1 */
+#define HDMIRX_LNKSTA_LNK_ERR1_OFFSET		((HDMIRX_LNKSTA_BASE) + (6 * 4))
+/* LNKSTA Link Error Counter Channel 2 */
+#define HDMIRX_LNKSTA_LNK_ERR2_OFFSET		((HDMIRX_LNKSTA_BASE) + (7 * 4))
+/* Packet ECC Error */
+#define HDMIRX_LNKSTA_PKT_ECC_ERR_OFFSET	((HDMIRX_LNKSTA_BASE) + (8 * 4))
+/* Tri-byte Analyzer Timing */
+#define HDMIRX_LNKSTA_TRIB_ANLZ_TIM_OFFSET	((HDMIRX_LNKSTA_BASE) + (9 * 4))
+/* Tri-byte HBP_HS */
+#define HDMIRX_LNKSTA_TRIB_HBP_HS_OFFSET	((HDMIRX_LNKSTA_BASE) + (10 * 4))
+/* Tri-byte Analyzer Line Size */
+#define HDMIRX_LNKSTA_TRIB_ANLZ_LN_ACT_OFFSET	((HDMIRX_LNKSTA_BASE) + (11 * 4))
+
+/* Fixed Rate Link (FRL) peripheral register offsets */
+#define HDMIRX_FRL_BASE				(8 * 64)
+/* FRL Identification */
+#define HDMIRX_FRL_ID_OFFSET			((HDMIRX_FRL_BASE) + (0 * 4))
+/* FRL Control */
+#define HDMIRX_FRL_CTRL_OFFSET			((HDMIRX_FRL_BASE) + (1 * 4))
+/* FRL Control Register Set offset */
+#define HDMIRX_FRL_CTRL_SET_OFFSET		((HDMIRX_FRL_BASE) + (2 * 4))
+/* FRL Control Register Clear offset */
+#define HDMIRX_FRL_CTRL_CLR_OFFSET		((HDMIRX_FRL_BASE) + (3 * 4))
+/* FRL Status */
+#define HDMIRX_FRL_STA_OFFSET			((HDMIRX_FRL_BASE) + (4 * 4))
+/* FRL Video Clock  to VCKE Ratio */
+#define HDMIRX_FRL_VCLK_VCKE_RATIO_OFFSET	((HDMIRX_FRL_BASE) + (7 * 4))
+/* FRL Video Clock */
+#define HDMIRX_FRL_SCDC_OFFSET			((HDMIRX_FRL_BASE) + (8 * 4))
+/* FRL Total Data */
+#define HDMIRX_FRL_RATIO_TOT_OFFSET		((HDMIRX_FRL_BASE) + (9 * 4))
+/* FRL Total Active Data */
+#define HDMIRX_FRL_RATIO_ACT_OFFSET		((HDMIRX_FRL_BASE) + (10 * 4))
+/* Reed-Solomon FEC Counter Data */
+#define HDMIRX_FRL_RSFC_CNT_OFFSET		((HDMIRX_FRL_BASE) + (11 * 4))
+/* FRL Error Count Data */
+#define HDMIRX_FRL_ERR_CNT1_OFFSET		((HDMIRX_FRL_BASE) + (12 * 4))
+/* Video Lock Count Data */
+#define HDMIRX_FRL_VID_LOCK_CNT_OFFSET		((HDMIRX_FRL_BASE) + (13 * 4))
+
+/* VER (Version Interface) peripheral register masks and shift */
+/* FRL SR/SSB period error during training period mask */
+#define HDMIRX_SR_SSB_ERR1_MASK			GENMASK(15, 0)
+/* FRL SR/SSB period error during NON-training period mask */
+#define HDMIRX_SR_SSB_ERR2_MASK			GENMASK(31, 16)
+
+/* FRL Word aligner tap select changed all lanes mask */
+#define HDMIRX_DBG_STA_WA_TAP_CHGALL_MASK	GENMASK(3, 0)
+/* Word aligner tap select changed lane 0 mask */
+#define HDMIRX_DBG_STA_WA_TAP_CHG0_MASK		BIT(0)
+/* Word aligner tap select changed lane 1 mask */
+#define HDMIRX_DBG_STA_WA_TAP_CHG1_MASK		BIT(1)
+/* Word aligner tap select changed lane 2 mask */
+#define HDMIRX_DBG_STA_WA_TAP_CHG2_MASK		BIT(2)
+/* FRL Word aligner tap select changed lane 3 mask */
+#define HDMIRX_DBG_STA_WA_TAP_CHG3_MASK		BIT(3)
+/* FRL Word aligner tap select changed all lanes mask */
+#define HDMIRX_DBG_STA_WA_LOCK_CHGALL_MASK	GENMASK(7, 4)
+/* Word aligner tap select changed lane 0 mask */
+#define HDMIRX_DBG_STA_WA_LOCK_CHG0_MASK	BIT(4)
+/* Word aligner tap select changed lane 1 mask */
+#define HDMIRX_DBG_STA_WA_LOCK_CHG1_MASK	BIT(5)
+/* Word aligner tap select changed lane 2 mask */
+#define HDMIRX_DBG_STA_WA_LOCK_CHG2_MASK	BIT(6)
+/* FRL Word aligner tap select changed lane 3 mask */
+#define HDMIRX_DBG_STA_WA_LOCK_CHG3_MASK	BIT(7)
+/* FRL Word aligner tap select changed all lanes mask */
+#define HDMIRX_DBG_STA_SCRM_LOCK_CHGALL_MASK	GENMASK(11, 8)
+/* Word aligner tap select changed lane 0 mask */
+#define HDMIRX_DBG_STA_SCRM_LOCK_CHG0_MASK	BIT(8)
+/* Word aligner tap select changed lane 1 mask */
+#define HDMIRX_DBG_STA_SCRM_LOCK_CHG1_MASK	BIT(9)
+/* Word aligner tap select changed lane 2 mask */
+#define HDMIRX_DBG_STA_SCRM_LOCK_CHG2_MASK	BIT(10)
+/* FRL Word aligner tap select changed lane 3 mask */
+#define HDMIRX_DBG_STA_SCRM_LOCK_CHG3_MASK	BIT(11)
+/* FRL Word aligner tap select changed all lanes mask */
+#define HDMIRX_DBG_STA_LANE_LOCK_CHGALL_MASK	GENMASK(15, 12)
+/* Word aligner tap select changed lane 0 mask */
+#define HDMIRX_DBG_STA_LANE_LOCK_CHG0_MASK	BIT(12)
+/* Word aligner tap select changed lane 1 mask */
+#define HDMIRX_DBG_STA_LANE_LOCK_CHG1_MASK	BIT(13)
+/* Word aligner tap select changed lane 2 mask */
+#define HDMIRX_DBG_STA_LANE_LOCK_CHG2_MASK	BIT(14)
+/* FRL Word aligner tap select changed lane 3 mask */
+#define HDMIRX_DBG_STA_LANE_LOCK_CHG3_MASK	BIT(15)
+/* Word aligner tap select changed lane 0 mask */
+#define HDMIRX_DBG_STA_SKEW_LOCK_CHG_MASK	BIT(16)
+
+/* PIO peripheral Control register masks */
+/* PIO Control Run mask */
+#define HDMIRX_PIO_CTRL_RUN_MASK		BIT(0)
+/* PIO Control Interrupt Enable mask */
+#define HDMIRX_PIO_CTRL_IE_MASK			BIT(1)
+
+/* PIO peripheral Status register masks */
+/* PIO Status Interrupt mask */
+#define HDMIRX_PIO_STA_IRQ_MASK			BIT(0)
+/* PIO Status Event mask */
+#define HDMIRX_PIO_STA_EVT_MASK			BIT(1)
+
+/* PIO peripheral PIO Out register masks and shifts */
+/* PIO Out Reset mask */
+#define HDMIRX_PIO_OUT_RESET_MASK		BIT(0)
+/* PIO Out video enable mask */
+#define HDMIRX_PIO_OUT_LNK_EN_MASK		BIT(1)
+/* PIO Out video enable mask */
+#define HDMIRX_PIO_OUT_VID_EN_MASK		BIT(2)
+/* PIO Out Hot-Plug Detect mask */
+#define HDMIRX_PIO_OUT_HPD_MASK			BIT(3)
+/* PIO Out Deep Color mask */
+#define HDMIRX_PIO_OUT_DEEP_COLOR_MASK		GENMASK(5, 4)
+/* PIO Out Pixel Rate mask */
+#define HDMIRX_PIO_OUT_PIXEL_RATE_MASK		GENMASK(7, 6)
+/* PIO Out Sample Rate mask */
+#define HDMIRX_PIO_OUT_SAMPLE_RATE_MASK		GENMASK(9, 8)
+/* PIO Out Color Space mask */
+#define HDMIRX_PIO_OUT_COLOR_SPACE_MASK		GENMASK(11, 10)
+/* PIO Out Scrambler mask */
+#define HDMIRX_PIO_OUT_SCRM_MASK		BIT(12)
+/* PIO Out Pixel Phase mask */
+#define HDMIRX_PIO_OUT_PP_MASK			GENMASK(18, 16)
+/* PIO Out Axis Enable mask */
+#define HDMIRX_PIO_OUT_AXIS_EN_MASK		BIT(19)
+/* PIO Out Deep Color shift */
+#define HDMIRX_PIO_OUT_DEEP_COLOR_SHIFT		4
+/* PIO Out Pixel Rate Shift */
+#define HDMIRX_PIO_OUT_PIXEL_RATE_SHIFT		6
+/* PIO Out Sample Rate shift */
+#define HDMIRX_PIO_OUT_SAMPLE_RATE_SHIFT	8
+/* PIO Out Color Space shift */
+#define HDMIRX_PIO_OUT_COLOR_SPACE_SHIFT	10
+/* PIO Out Pixel Phase shift */
+#define HDMIRX_PIO_OUT_PP_SHIFT			16
+/* PIO Out Bridge_YUV420 mask */
+#define HDMIRX_PIO_OUT_BRIDGE_YUV420_MASK	BIT(29)
+/* PIO Out Bridge_Pixel drop mask */
+#define HDMIRX_PIO_OUT_BRIDGE_PIXEL_MASK	BIT(30)
+
+/* PIO Out INT_VRST mask */
+#define HDMIRX_PIO_OUT_INT_VRST_MASK		BIT(0)
+/* PIO Out INT_LRST mask */
+#define HDMIRX_PIO_OUT_INT_LRST_MASK		BIT(20)
+/* PIO Out EXT_VRST mask */
+#define HDMIRX_PIO_OUT_EXT_VRST_MASK		BIT(21)
+/* PIO Out EXT_SYSRST mask */
+#define HDMIRX_PIO_OUT_EXT_SYSRST_MASK		BIT(22)
+
+/* PIO peripheral PIO In register masks */
+/* PIO In cable detect mask */
+#define HDMIRX_PIO_IN_DET_MASK			BIT(0)
+/* PIO In link ready mask */
+#define HDMIRX_PIO_IN_LNK_RDY_MASK		BIT(1)
+/* PIO In video ready mask */
+#define HDMIRX_PIO_IN_VID_RDY_MASK		BIT(2)
+/* PIO In Mode mask */
+#define HDMIRX_PIO_IN_MODE_MASK			BIT(3)
+/* PIO In Scrambler lock 0 mask */
+#define HDMIRX_PIO_IN_SCRAMBLER_LOCK0_MASK	BIT(4)
+/* PIO In Scrambler lock 1 mask */
+#define HDMIRX_PIO_IN_SCRAMBLER_LOCK1_MASK	BIT(5)
+/* PIO In Scrambler lock 2 mask */
+#define HDMIRX_PIO_IN_SCRAMBLER_LOCK2_MASK	BIT(6)
+/* PIO In SCDC scrambler enable mask */
+#define HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK	BIT(7)
+/* PIO In SCDC TMDS clock ratio mask */
+#define HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK	BIT(8)
+/* PIO In alinger lock mask */
+#define HDMIRX_PIO_IN_ALIGNER_LOCK_MASK		BIT(9)
+/* PIO In bridge overflow mask */
+#define HDMIRX_PIO_IN_BRDG_OVERFLOW_MASK	BIT(10)
+
+/* Timer peripheral Control register masks */
+/* TMR Control Run mask */
+#define HDMIRX_TMR1_CTRL_RUN_MASK		BIT(0)
+/* TMR Control Interrupt Enable mask */
+#define HDMIRX_TMR1_CTRL_IE_MASK		BIT(1)
+/* TMR Control Run mask */
+#define HDMIRX_TMR2_CTRL_RUN_MASK		BIT(2)
+/* TMR Control Interrupt Enable mask */
+#define HDMIRX_TMR2_CTRL_IE_MASK		BIT(3)
+/* TMR Control Run mask */
+#define HDMIRX_TMR3_CTRL_RUN_MASK		BIT(4)
+/* TMR Control Interrupt Enable mask */
+#define HDMIRX_TMR3_CTRL_IE_MASK		BIT(5)
+/* TMR Control Run mask */
+#define HDMIRX_TMR4_CTRL_RUN_MASK		BIT(6)
+/* TMR Control Interrupt Enable mask */
+#define HDMIRX_TMR4_CTRL_IE_MASK		BIT(7)
+
+/* Timer peripheral Status register masks */
+/* TMR Status Interrupt mask */
+#define HDMIRX_TMR_STA_IRQ_MASK			BIT(0)
+/* TMR Status counter Event mask */
+#define HDMIRX_TMR1_STA_CNT_EVT_MASK		BIT(1)
+/* TMR Status counter Event mask */
+#define HDMIRX_TMR2_STA_CNT_EVT_MASK		BIT(3)
+/* TMR Status counter Event mask */
+#define HDMIRX_TMR3_STA_CNT_EVT_MASK		BIT(5)
+/* TMR Status counter Event mask */
+#define HDMIRX_TMR4_STA_CNT_EVT_MASK		BIT(7)
+
+/* Video timing detector peripheral Control register masks and shift */
+/* VTD Control Run mask */
+#define HDMIRX_VTD_CTRL_RUN_MASK		BIT(0)
+/* VTD Control Interrupt Enable mask */
+#define HDMIRX_VTD_CTRL_IE_MASK			BIT(1)
+/* VTD Control field polarity mask */
+#define HDMIRX_VTD_CTRL_FIELD_POL_MASK		BIT(2)
+/* VTD Control field polarity mask */
+#define HDMIRX_VTD_CTRL_SYNC_LOSS_MASK		BIT(3)
+/* VTD Control timebase shift */
+#define HDMIRX_VTD_CTRL_TIMEBASE_SHIFT		8
+/* VTD Control timebase mask */
+#define HDMIRX_VTD_CTRL_TIMERBASE_MASK		GENMASK(31, 8)
+
+#define HDMIRX_VTD_VF0_MASK			GENMASK(15, 0)
+#define HDMIRX_VTD_VF1_MASK			GENMASK(31, 16)
+
+/* Video timing detector peripheral Status register masks */
+/* VTD Status Interrupt mask */
+#define HDMIRX_VTD_STA_IRQ_MASK			BIT(0)
+/* VTD Status timebase event mask */
+#define HDMIRX_VTD_STA_TIMEBASE_EVT_MASK	BIT(1)
+/* VTD Status Vsync Polarity mask */
+#define HDMIRX_VTD_STA_VS_POL_MASK		BIT(3)
+/* VTD Status Hsync Polarity mask */
+#define HDMIRX_VTD_STA_HS_POL_MASK		BIT(4)
+/* VTD Status Format mask */
+#define HDMIRX_VTD_STA_FMT_MASK			BIT(5)
+/* VTD Status Sync Loss mask */
+#define HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK	BIT(6)
+
+/* DDC peripheral Control register masks */
+/* DDC Control Run mask */
+#define HDMIRX_DDC_CTRL_RUN_MASK		BIT(0)
+/* DDC Control Interrupt enable mask */
+#define HDMIRX_DDC_CTRL_IE_MASK			BIT(1)
+/* DDC Control EDID enable mask */
+#define HDMIRX_DDC_CTRL_EDID_EN_MASK		BIT(2)
+/* DDC Control SCDC enable mask */
+#define HDMIRX_DDC_CTRL_SCDC_EN_MASK		BIT(3)
+/* DDC Control HDCP enable mask */
+#define HDMIRX_DDC_CTRL_HDCP_EN_MASK		BIT(4)
+/* DDC Control SCDC clear mask */
+#define HDMIRX_DDC_CTRL_SCDC_CLR_MASK		BIT(5)
+/* DDC Control write message clear mask */
+#define HDMIRX_DDC_CTRL_WMSG_CLR_MASK		BIT(6)
+/* DDC Control read message clear mask */
+#define HDMIRX_DDC_CTRL_RMSG_CLR_MASK		BIT(7)
+/* DDC Control HDCP mode mask */
+#define HDMIRX_DDC_CTRL_HDCP_MODE_MASK		BIT(8)
+/* DDC Control SCDC Read Write Event mask */
+#define HDMIRX_DDC_CTRL_SCDC_RD_WR_EVT_EN_MASK	BIT(9)
+
+/* DDC peripheral Status register masks */
+/* DDC Status Interrupt mask */
+#define HDMIRX_DDC_STA_IRQ_MASK			BIT(0)
+/* DDC Status Event mask */
+#define HDMIRX_DDC_STA_EVT_MASK			BIT(1)
+/* DDC Status Busy mask */
+#define HDMIRX_DDC_STA_BUSY_MASK		BIT(2)
+/* DDC Status state of the SCL input mask */
+#define HDMIRX_DDC_STA_SCL_MASK			BIT(3)
+/* DDC Status state of the SDA input mask */
+#define HDMIRX_DDC_STA_SDA_MASK			BIT(4)
+/* DDC Status HDCP AKSV event mask */
+#define HDMIRX_DDC_STA_HDCP_AKSV_EVT_MASK	BIT(5)
+/* DDC Status HDCP write message buffer new event mask */
+#define HDMIRX_DDC_STA_HDCP_WMSG_NEW_EVT_MASK	BIT(6)
+/* DDC Status HDCP read message buffer end event mask */
+#define HDMIRX_DDC_STA_HDCP_RMSG_END_EVT_MASK	BIT(7)
+/* DDC Status HDCP read message buffer not completed event mask */
+#define HDMIRX_DDC_STA_HDCP_RMSG_NC_EVT_MASK	BIT(8)
+/* DDC Status HDCP 1.4 protocol flag */
+#define HDMIRX_DDC_STA_HDCP_1_PROT_MASK		BIT(9)
+/* DDC Status HDCP 2.2 protocol flag */
+#define HDMIRX_DDC_STA_HDCP_2_PROT_MASK		BIT(10)
+/* DDC Status HDCP 1.4 protocol event flag */
+#define HDMIRX_DDC_STA_HDCP_1_PROT_EVT_MASK	BIT(11)
+/* DDC Status HDCP 2.2 protocol event flag */
+#define HDMIRX_DDC_STA_HDCP_2_PROT_EVT_MASK	BIT(12)
+/* DDC Status SCDC Read Write event flag */
+#define HDMIRX_DDC_STA_SCDC_RD_WR_EVT_MASK	BIT(13)
+/* DDC Status EDID words mask */
+#define HDMIRX_DDC_STA_EDID_WORDS_MASK		GENMASK(15, 0)
+/* DDC Status HDCP 2.2 write message buffer words mask */
+#define HDMIRX_DDC_STA_HDCP_WMSG_WORDS_MASK	GENMASK(10, 0)
+/* DDC Status HDCP 2.2 write message buffer empty mask */
+#define HDMIRX_DDC_STA_HDCP_WMSG_EP_MASK	BIT(11)
+/* DDC Status HDCP 2.2 read message buffer words mask */
+#define HDMIRX_DDC_STA_HDCP_RMSG_WORDS_MASK	GENMASK(26, 16)
+/* DDC Status HDCP 2.2 read message buffer empty mask */
+#define HDMIRX_DDC_STA_HDCP_RMSG_EP_MASK	BIT(27)
+
+/* AUX peripheral Control register masks */
+/* AUX Control Run mask */
+#define HDMIRX_AUX_CTRL_RUN_MASK		BIT(0)
+/* AUX Control Interrupt Enable mask */
+#define HDMIRX_AUX_CTRL_IE_MASK			BIT(1)
+
+/* AUX peripheral Status register masks and shifts */
+/* AUX Status Interrupt mask */
+#define HDMIRX_AUX_STA_IRQ_MASK			BIT(0)
+/* AUX Status New Packet mask */
+#define HDMIRX_AUX_STA_NEW_MASK			BIT(1)
+/* AUX Status New Packet mask */
+#define HDMIRX_AUX_STA_ERR_MASK			BIT(2)
+/* AUX Status AVI infoframe mask */
+#define HDMIRX_AUX_STA_AVI_MASK			BIT(3)
+/* AUX Status General control packet mask */
+#define HDMIRX_AUX_STA_GCP_MASK			BIT(4)
+/* AUX Status FIFO Empty mask */
+#define HDMIRX_AUX_STA_FIFO_EP_MASK		BIT(5)
+/* AUX Status FIFO Full mask */
+#define HDMIRX_AUX_STA_FIFO_FL_MASK		BIT(6)
+/* AUX Status Dynamic HDR event mask */
+#define HDMIRX_AUX_STA_DYN_HDR_EVT_MASK		BIT(20)
+/* AUX Status VRR CD mask */
+#define HDMIRX_AUX_STA_VRR_CD_EVT_MASK		BIT(21)
+/* AUX Status FSYNC CD mask */
+#define HDMIRX_AUX_STA_FSYNC_CD_EVT_MASK	BIT(22)
+/* AUX Status GCP ColorDepth mask */
+#define HDMIRX_AUX_STA_GCP_CD_EVT_MASK		BIT(25)
+/* AUX Status GCP avmute mask */
+#define HDMIRX_AUX_STA_GCP_AVMUTE_MASK		BIT(31)
+/* AUX Status AVI VIC mask */
+#define HDMIRX_AUX_STA_AVI_VIC_MASK		GENMASK(15, 8)
+/* AUX Status AVI colorspace mask */
+#define HDMIRX_AUX_STA_AVI_CS_MASK		GENMASK(17, 16)
+/* AUX Status GCP colordepth mask */
+#define HDMIRX_AUX_STA_GCP_CD_MASK		GENMASK(27, 26)
+/* AUX Status GCP pixel phase mask */
+#define HDMIRX_AUX_STA_GCP_PP_MASK		GENMASK(30, 28)
+
+/* Audio peripheral Control register masks */
+/* AUD Control Run mask */
+#define HDMIRX_AUD_CTRL_RUN_MASK		BIT(0)
+/* AUD Control Interrupt Enable mask */
+#define HDMIRX_AUD_CTRL_IE_MASK			BIT(1)
+/* AUD Control ACR Update Event Enable mask */
+#define HDMIRX_AUD_CTRL_ACR_UPD_EVT_EN_MASK	BIT(2)
+
+/* AUD peripheral Status register masks and shift */
+/* AUD Status Interrupt mask */
+#define HDMIRX_AUD_STA_IRQ_MASK			BIT(0)
+/* AUD Status Event mask */
+#define HDMIRX_AUD_STA_ACT_EVT_MASK		BIT(1)
+/* AUD Status Event mask */
+#define HDMIRX_AUD_STA_CH_EVT_MASK		BIT(2)
+/* AUD Status Active mask */
+#define HDMIRX_AUD_STA_ACT_MASK			BIT(3)
+/* AUD Status Audio channel mask */
+#define HDMIRX_AUD_STA_AUD_CH_MASK		GENMASK(5, 4)
+/* AUD Status Audio Format mask */
+#define HDMIRX_AUD_STA_AUD_FMT_MASK		GENMASK(8, 6)
+/* AUD Status ACR Update mask */
+#define HDMIRX_AUD_STA_ACR_UPD_MASK		BIT(9)
+
+/* Link Status (LNKSTA) peripheral Control register masks */
+/* LNKSTA Control Run mask */
+#define HDMIRX_LNKSTA_CTRL_RUN_MASK		BIT(0)
+/* LNKSTA Control Interrupt Enable mask */
+#define HDMIRX_LNKSTA_CTRL_IE_MASK		BIT(1)
+/* LNKSTA Control Error Clear mask */
+#define HDMIRX_LNKSTA_CTRL_ERR_CLR_MASK		BIT(2)
+
+/* Link Status (LNKSTA) peripheral Status register masks */
+/* LNKSTA Status Interrupt mask */
+#define HDMIRX_LNKSTA_STA_IRQ_MASK		BIT(0)
+/* LNKSTA Status Maximum Errors mask */
+#define HDMIRX_LNKSTA_STA_ERR_MAX_MASK		BIT(1)
+#define HDMIRX_LNKSTA_STA_DCS_8CD_LOCK_MASK	BIT(2)
+#define HDMIRX_LNKSTA_STA_DCS_DEEP_LOCK_MASK	BIT(3)
+
+/* Tri-byte Analyzer register masks */
+/* Tri-byte analyzer timing changed count mask */
+#define HDMIRX_TRIB_ANLZ_TIM_CHGD_CNT_MASK	GENMASK(15, 0)
+/* Tri-byte analyzer timing vsync polarity mask */
+#define HDMIRX_TRIB_ANLZ_TIM_VS_POL_MASK	BIT(16)
+/* Tri-byte analyzer timing hsync polarity mask */
+#define HDMIRX_TRIB_ANLZ_TIM_HS_POL_MASK	BIT(17)
+
+/* Tri-byte Analyzer register masks */
+/* Tri-byte hsync size mask */
+#define HDMIRX_TRIB_HBP_HS_HS_SZ_MASK		GENMASK(15, 0)
+/* Tri-byte hbp size mask */
+#define HDMIRX_TRIB_HBP_HS_HBP_SZ_MASK		GENMASK(31, 16)
+
+/* Tri-byte Analyzer register masks */
+/* Tri-byte analyzer act size mask */
+#define HDMIRX_TRIB_ANLZ_LN_ACT_ACT_SZ_MASK	GENMASK(15, 0)
+/* Tri-byte analyzer line act mask */
+#define HDMIRX_TRIB_ANLZ_LN_ACT_LN_SZ_MASK	GENMASK(31, 16)
+
+/* FRL Control register masks */
+/* FRL Control Resetn mask */
+#define HDMIRX_FRL_CTRL_RSTN_MASK			BIT(0)
+/* FRL Control Interrupt Enable mask */
+#define HDMIRX_FRL_CTRL_IE_MASK				BIT(1)
+/* FRL Control Clock Ratio Update Event Enable mask */
+#define HDMIRX_FRL_CTRL_CLK_RATIO_UPD_EVT_EN_MASK	BIT(2)
+/* FRL Control Skew Event Enable mask */
+#define HDMIRX_FRL_CTRL_SKEW_EVT_EN_MASK		BIT(3)
+/* FRL Control FLT Clear mask */
+#define HDMIRX_FRL_CTRL_FLT_CLR_MASK			BIT(5)
+/* FRL Control FLT Threshold mask */
+#define HDMIRX_FRL_CTRL_FLT_THRES_MASK			GENMASK(13, 6)
+/* FRL Control FRL Rate Write Event Enable */
+#define HDMIRX_FRL_CTRL_FRL_RATE_WR_EVT_EN_MASK		BIT(14)
+/* FRL Control DPACK Reset mask */
+#define HDMIRX_FRL_CTRL_DPACK_RST_MASK			BIT(15)
+/* FRL Control DPACK Error Counter Clear mask */
+#define HDMIRX_FRL_CTRL_DPACK_ERR_CNT_CLR_MASK		BIT(16)
+/* FRL Control DPACK Auto Reset Disable mask */
+#define HDMIRX_FRL_CTRL_DPACK_AUTO_RST_DIS_MASK		BIT(17)
+/* FRL Control Video Lock Reset Disable Mask */
+#define HDMIRX_FRL_CTRL_VID_LOCK_RST_DIS_MASK		BIT(19)
+/* FRL PARS module reset */
+#define HDMIRX_FRL_CTRL_PARS_RST_MASK			BIT(21)
+/* FRL FEC module reset */
+#define HDMIRX_FRL_CTRL_FEC_RST_MASK			BIT(22)
+/* FRL MAP module reset */
+#define HDMIRX_FRL_CTRL_MAP_RST_MASK			BIT(23)
+/* FRL SKEW module reset */
+#define HDMIRX_FRL_CTRL_SKEW_RST_MASK			BIT(24)
+
+/* FRL Status register masks */
+/* FRL Status Interrupt mask */
+#define HDMIRX_FRL_STA_IRQ_MASK				BIT(0)
+/* FRL Status Event mask */
+#define HDMIRX_FRL_STA_EVT_MAS				BIT(1)
+/* FRL Status FLT Pattern Match event mask */
+#define HDMIRX_FRL_STA_FLT_PM_EVT_MASK			BIT(2)
+/* FRL Status FLT Pattern Match All Lanes mask */
+#define HDMIRX_FRL_STA_FLT_PM_ALLL_MASK			GENMASK(6, 3)
+/* FRL Status FLT Pattern MatchLane 0 mask */
+#define HDMIRX_FRL_STA_FLT_PM_L0_MASK			BIT(3)
+/* FRL Status FLT Pattern MatchLane 1 mask */
+#define HDMIRX_FRL_STA_FLT_PM_L1_MASK			BIT(4)
+/* FRL Status FLT Pattern MatchLane 2 mask */
+#define HDMIRX_FRL_STA_FLT_PM_L2_MASK			BIT(5)
+/* FRL Status FLT Pattern MatchLane 3 mask */
+#define HDMIRX_FRL_STA_FLT_PM_L3_MASK			BIT(6)
+/* FRL Status FLT Update event mask */
+#define HDMIRX_FRL_STA_FLT_UPD_EVT_MASK			BIT(7)
+/* FRL Status FRL Rate change event mask */
+#define HDMIRX_FRL_STA_RATE_EVT_MASK			BIT(8)
+/* FRL Status Lane Lock event mask */
+#define HDMIRX_FRL_STA_LANE_LOCK_EVT_MASK		BIT(9)
+/* FRL Status Clock Ratio Update event mask */
+#define HDMIRX_FRL_STA_CLK_RATIO_UPD_EVT_MASK		BIT(10)
+/* FRL Status Skew Lock event mask */
+#define HDMIRX_FRL_STA_SKEW_LOCK_EVT_MASK		BIT(11)
+/* FRL Status Lane Lock All Lanes mask */
+#define HDMIRX_FRL_STA_LANE_LOCK_ALLL_MASK		GENMASK(15, 12)
+/* FRL Status Lane Lock L0 mask */
+#define HDMIRX_FRL_STA_LANE_LOCK_L0_MASK		BIT(12)
+/* FRL Status Lane Lock L1 mask */
+#define HDMIRX_FRL_STA_LANE_LOCK_L1_MASK		BIT(13)
+/* FRL Status Lane Lock L2 mask */
+#define HDMIRX_FRL_STA_LANE_LOCK_L2_MASK		BIT(14)
+/* FRL Status Lane Lock L3 mask */
+#define HDMIRX_FRL_STA_LANE_LOCK_L3_MASK		BIT(15)
+/* FRL Status Aligner Lock All Lanes mask */
+#define HDMIRX_FRL_STA_WA_LOCK_ALLL_MASK		GENMASK(19, 16)
+/* FRL Status Aligner Lock L0 mask */
+#define HDMIRX_FRL_STA_WA_LOCK_L0_MASK			BIT(16)
+/* FRL Status Aligner Lock L1 mask */
+#define HDMIRX_FRL_STA_WA_LOCK_L1_MASK			BIT(17)
+/* FRL Status Aligner Lock L2 mask */
+#define HDMIRX_FRL_STA_WA_LOCK_L2_MASK			BIT(18)
+/* FRL Status Aligner Lock L3 mask */
+#define HDMIRX_FRL_STA_WA_LOCK_L3_MASK			BIT(19)
+/* FRL Status Scrambler All Lanes mask */
+#define HDMIRX_FRL_STA_SCRM_LOCK_ALLL_MASK		GENMASK(23, 20)
+/* FRL Status Scrambler Lock L0 mask */
+#define HDMIRX_FRL_STA_SCRM_LOCK_L0_MASK		BIT(20)
+/* FRL Status Scrambler Lock L1 mask */
+#define HDMIRX_FRL_STA_SCRM_LOCK_L1_MASK		BIT(21)
+/* FRL Status Scrambler Lock L2 mask */
+#define HDMIRX_FRL_STA_SCRM_LOCK_L2_MASK		BIT(22)
+/* FRL Status Scrambler Lock L3 mask */
+#define HDMIRX_FRL_STA_SCRM_LOCK_L3_MASK		BIT(23)
+/* FRL Status Skew Lock mask */
+#define HDMIRX_FRL_STA_SKEW_LOCK_MASK			BIT(24)
+/* FRL Status Video STR mask */
+#define HDMIRX_FRL_STA_STR_MASK				BIT(25)
+/* FRL Status Video Lock mask */
+#define HDMIRX_FRL_STA_VID_LOCK_MASK			BIT(26)
+/* FRL Status Mode mask */
+#define HDMIRX_FRL_STA_FRL_MODE_MASK			BIT(27)
+/* FRL Status Lanes mask */
+#define HDMIRX_FRL_STA_FRL_LANES_MASK			BIT(28)
+/* FRL Status Rate mask */
+#define HDMIRX_FRL_STA_FRL_RATE_MASK			GENMASK(31, 29)
+
+/* FRL Link Clock register masks */
+/* FRL Link Clock mask */
+#define HDMIRX_FRL_LNK_CLK_MASK		0xFFFFF
+/* FRL Video Clock mask */
+#define HDMIRX_FRL_VID_CLK_MASK		0xFFFFF
+
+/* FRL SCDC register masks */
+/* FRL SCDC Address mask */
+#define HDMIRX_FRL_SCDC_ADDR_MASK			GENMASK(7, 0)
+/* FRL SCDC Data mask */
+#define HDMIRX_FRL_SCDC_DAT_MASK			GENMASK(15, 8)
+/* FRL SCDC Data Shift */
+#define HDMIRX_FRL_SCDC_DAT_SHIFT			8
+/* FRL SCDC Write mask */
+#define HDMIRX_FRL_SCDC_WR_MASK				BIT(16)
+/* FRL SCDC Read mask */
+#define HDMIRX_FRL_SCDC_RD_MASK				BIT(17)
+/* FRL SCDC Ready mask */
+#define HDMIRX_FRL_SCDC_RDY_MASK			BIT(18)
+
+#define HDMIRX_FRL_RATIO_TOT_MASK	0xFFFFFF
+#define HDMIRX_FRL_RATIO_ACT_MASK	0xFFFFFF
+
+#define HDMIRX_FRL_ERR_CNT1_DPACK_ERR_CNT_MASK		GENMASK(31, 16)
+#define HDMIRX_FRL_ERR_CNT1_RSCC_ERR_CNT_MASK		GENMASK(15, 0)
+
+/* Peripheral ID and General shift values */
+/* 16 shift value */
+#define HDMIRX_SHIFT_16		16
+/* 16 bit mask value */
+#define HDMIRX_MASK_16		GENMASK(15, 0)
+/* PIO ID */
+#define HDMIRX_PIO_ID		0x2200
+
+#endif /* __XILINX_HDMIRX_HW_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-hdmirxss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-hdmirxss.c
@@ -0,0 +1,3775 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx HDMI 2.1 Rx Subsystem driver
+ *
+ * Copyright (c) 2021 Xilinx
+ * Author: Vishal Sagar <vishal.sagar@xilinx.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <media/media-entity.h>
+#include <media/v4l2-dv-timings.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-subdev.h>
+#include "xilinx-hdmirx-hw.h"
+
+#define XHDMI_MAX_LANES		(4)
+#define XEDID_BLOCKS_MAX	(10)
+#define XEDID_BLOCK_SIZE	(128)
+
+#define AXILITE_FREQ		clk_get_rate(xhdmi->clks[0].clk)
+#define TIME_10MS		(AXILITE_FREQ / 100)
+#define TIME_16MS		(AXILITE_FREQ * 10 / 625)
+#define TIME_200MS		(AXILITE_FREQ / 5)
+
+#define MAX_VID_PROP_TRIES	7
+#define MAX_FIELDS		2
+#define COREPIXPERCLK		4
+#define MAX_FRL_RETRY		(256)
+#define DEFAULT_LTPTHRESHOLD	(150)
+
+enum xhdmirx_stream_state {
+	XSTREAM_IDLE = 0,
+	XSTREAM_INIT = 1,
+	XSTREAM_LOCK = 2,
+	XSTREAM_ARM = 3,
+	XSTREAM_UP = 4,
+	XSTREAM_DOWN = 5,
+	XSTATE_FRL_LINK_TRAININIG = 6,
+	XSTREAM_MAX_STATE = 7,
+};
+
+enum xhdmirx_syncstatus {
+	XSYNCSTAT_SYNC_LOSS = 0,
+	XSYNCSTAT_SYNC_EST = 1,
+};
+
+enum xcolorspace {
+	XCS_RGB = 0,
+	XCS_YUV422 = 1,
+	XCS_YUV444 = 2,
+	XCS_YUV420 = 3,
+};
+
+enum xcolordepth {
+	XCD_8 = 8,
+	XCD_10 = 10,
+	XCD_12 = 12,
+	XCD_16 = 16,
+};
+
+/**
+ * struct xtiming - Timing struct
+ *
+ * @hact: Horizontal Active
+ * @htot: Horizontal Total
+ * @hbp: Horizontal Backporch
+ * @hfp: Horizontal Frontporch
+ * @hsw: Horizontal Syncwidth
+ * @vact: Vertical Active
+ * @vtot: Vertical Total
+ * @vfp: Vertical Frontporch
+ * @vbp: Vertical Backporch
+ * @vsw: Vertical Syncwidth
+ * @vsyncpol: Vertical polarity
+ * @hsyncpol: Horizontal polarity
+ */
+struct xtiming {
+	u16 hact;
+	u16 htot;
+	u16 hbp;
+	u16 hfp;
+	u16 hsw;
+	u16 vact;
+	u16 vtot[MAX_FIELDS];
+	u16 vfp[MAX_FIELDS];
+	u16 vbp[MAX_FIELDS];
+	u16 vsw[MAX_FIELDS];
+	u8 vsyncpol;
+	u8 hsyncpol;
+};
+
+/**
+ * struct xvideostream - Video stream structure
+ * @timing: stream timing struct
+ * @colorspace: color space of incoming stream RGB/YUV 444/422/420
+ * @colordepth: color depth 8/10/12/16 bpc
+ * @framerate: Frame rate of stream
+ * @isinterlaced: stream is interlaced or progressive
+ */
+struct xvideostream {
+	struct xtiming timing;
+	enum xcolorspace colorspace;
+	enum xcolordepth colordepth;
+	u32 framerate;
+	bool isinterlaced;
+};
+
+/* FRL SCDC Fields */
+enum xhdmi_frlscdcfieldtype {
+	XSCDCFIELD_SINK_VER = 0,
+	XSCDCFIELD_SOURCE_VER = 1,
+	XSCDCFIELD_CED_UPDATE = 2,
+	XSCDCFIELD_SOURCE_TEST_UPDATE = 3,
+	XSCDCFIELD_FRL_START = 4,
+	XSCDCFIELD_FLT_UPDATE = 5,
+	XSCDCFIELD_RSED_UPDATE = 6,
+	XSCDCFIELD_SCRAMBLER_EN = 7,
+	XSCDCFIELD_SCRAMBLER_STAT = 8,
+	XSCDCFIELD_FLT_NO_RETRAIN = 9,
+	XSCDCFIELD_FRL_RATE = 10,
+	XSCDCFIELD_FFE_LEVELS = 11,
+	XSCDCFIELD_FLT_NO_TIMEOUT = 12,
+	XSCDCFIELD_LNS_LOCK = 13,
+	XSCDCFIELD_FLT_READY = 14,
+	XSCDCFIELD_LN0_LTP_REQ = 15,
+	XSCDCFIELD_LN1_LTP_REQ = 16,
+	XSCDCFIELD_LN2_LTP_REQ = 17,
+	XSCDCFIELD_LN3_LTP_REQ = 18,
+	XSCDCFIELD_CH0_ERRCNT_LSB = 19,
+	XSCDCFIELD_CH0_ERRCNT_MSB = 20,
+	XSCDCFIELD_CH1_ERRCNT_LSB = 21,
+	XSCDCFIELD_CH1_ERRCNT_MSB = 22,
+	XSCDCFIELD_CH2_ERRCNT_LSB = 23,
+	XSCDCFIELD_CH2_ERRCNT_MSB = 24,
+	XSCDCFIELD_CED_CHECKSUM = 25,
+	XSCDCFIELD_CH3_ERRCNT_LSB = 26,
+	XSCDCFIELD_CH3_ERRCNT_MSB = 27,
+	XSCDCFIELD_RSCCNT_LSB = 28,
+	XSCDCFIELD_RSCCNT_MSB = 29,
+	XSCDCFIELD_SIZE = 30,
+};
+
+/* FRL Training States */
+enum xhdmi_frltrainingstate {
+	XFRLSTATE_LTS_L = 0,
+	XFRLSTATE_LTS_2 = 1,
+	XFRLSTATE_LTS_3_RATE_CH = 2,
+	XFRLSTATE_LTS_3_ARM_LNK_RDY = 3,
+	XFRLSTATE_LTS_3_ARM_VID_RDY = 4,
+	XFRLSTATE_LTS_3_LTP_DET = 5,
+	XFRLSTATE_LTS_3_TMR = 6,
+	XFRLSTATE_LTS_3 = 7,
+	XFRLSTATE_LTS_3_RDY = 8,
+	XFRLSTATE_LTS_P = 9,
+	XFRLSTATE_LTS_P_TIMEOUT = 10,
+	/* LTS:P (FRL_START = 1) */
+	XFRLSTATE_LTS_P_FRL_RDY = 11,
+	/* LTS:P (Skew Locked) */
+	XFRLSTATE_LTS_P_VID_RDY = 12,
+};
+
+/* LTP type */
+enum xhdmi_frlltptype {
+	XLTP_SUCCESS = 0,
+	XLTP_ALL_ONES = 1,
+	XLTP_ALL_ZEROES = 2,
+	XLTP_NYQUIST_CLOCK = 3,
+	XLTP_RXDDE_COMPLIANCE = 4,
+	XLTP_LFSR0 = 5,
+	XLTP_LFSR1 = 6,
+	XLTP_LFSR2 = 7,
+	XLTP_LFSR3 = 8,
+	XLTP_FFE_CHANGE = 0xE,
+	XLTP_RATE_CHANGE = 0xF,
+};
+
+union xhdmi_frlffeadjtype {
+	u32 data;
+	u8 byte[4];
+};
+
+union xhdmi_frlltp {
+	u32 data;
+	u8 byte[4];
+};
+
+struct xhdmi_frlscdcfield {
+	u8 offset;
+	u8 mask;
+	u8 shift;
+};
+
+static const struct xhdmi_frlscdcfield frlscdcfield[XSCDCFIELD_SIZE] = {
+	{0x01, 0xFF, 0},	/* XSCDCFIELD_SINK_VER */
+	{0x02, 0xFF, 0},	/* XSCDCFIELD_SOURCE_VER */
+	{0x10, 0x01, 1},	/* XSCDCFIELD_CED_UPDATE */
+	{0x10, 0x01, 3},	/* XSCDCFIELD_SOURCE_TEST_UPDATE */
+	{0x10, 0x01, 4},	/* XSCDCFIELD_FRL_START */
+	{0x10, 0x01, 5},	/* XSCDCFIELD_FLT_UPDATE */
+	{0x10, 0x01, 6},	/* XSCDCFIELD_RSED_UPDATE */
+	{0x20, 0x03, 0},	/* XSCDCFIELD_SCRAMBLER_EN */
+	{0x21, 0x01, 0},	/* XSCDCFIELD_SCRAMBLER_STAT */
+	{0x30, 0x01, 1},	/* XSCDCFIELD_FLT_NO_RETRAIN */
+	{0x31, 0x0F, 0},	/* XSCDCFIELD_FRL_RATE */
+	{0x31, 0x0F, 4},	/* XSCDCFIELD_FFE_LEVELS */
+	{0x35, 0x01, 5},	/* XSCDCFIELD_FLT_NO_TIMEOUT */
+	{0x40, 0x0F, 1},	/* XSCDCFIELD_LNS_LOCK */
+	{0x40, 0x01, 6},	/* XSCDCFIELD_FLT_READY */
+	{0x41, 0x0F, 0},	/* XSCDCFIELD_LN0_LTP_REQ */
+	{0x41, 0x0F, 4},	/* XSCDCFIELD_LN1_LTP_REQ */
+	{0x42, 0x0F, 0},	/* XSCDCFIELD_LN2_LTP_REQ */
+	{0x42, 0x0F, 4},	/* XSCDCFIELD_LN3_LTP_REQ */
+	{0x50, 0xFF, 0},	/* XSCDCFIELD_CH0_ERRCNT_LSB */
+	{0x51, 0xFF, 0},	/* XSCDCFIELD_CH0_ERRCNT_MSB */
+	{0x52, 0xFF, 0},	/* XSCDCFIELD_CH1_ERRCNT_LSB */
+	{0x53, 0xFF, 0},	/* XSCDCFIELD_CH1_ERRCNT_MSB */
+	{0x54, 0xFF, 0},	/* XSCDCFIELD_CH2_ERRCNT_LSB */
+	{0x55, 0xFF, 0},	/* XSCDCFIELD_CH2_ERRCNT_MSB */
+	{0x56, 0xFF, 0},	/* XSCDCFIELD_CED_CHECKSUM */
+	{0x57, 0xFF, 0},	/* XSCDCFIELD_CH3_ERRCNT_LSB */
+	{0x58, 0xFF, 0},	/* XSCDCFIELD_CH3_ERRCNT_MSB */
+	{0x59, 0xFF, 0},	/* XSCDCFIELD_RSCCNT_LSB */
+	{0x5A, 0xFF, 0},	/* XSCDCFIELD_RSCCNT_MSB */
+};
+
+/**
+ * struct xhdmirx_frl - FRL related structure
+ * @trainingstate: Fixed Rate Link State
+ * @timercnt: FRL timer
+ * @linerate: Current line rate from FRL rate
+ * @curfrlrate: Current FRL rate supported
+ * @lanes: Current number of lanes used
+ * @ffelevels: Number of supported FFE levels for current FRL rate
+ * @ffesuppflag: RX core's support for FFE levels
+ * @fltupdateasserted: Flag for FLT update asserted
+ * @ltp: LTP to be detected by the RX core and queried by source
+ * @defaultltp: LTP which will be used by Rx core for link training
+ * @laneffeadjreq: RxFFE for each lane
+ * @fltnotimeout: Flag for no timeout
+ * @fltnoretrain: Flag for no retrain
+ * @ltpmatchwaitcounts: counter for link training pattern match waiting
+ * @ltpmatchedcounts: counter for link training pattern matched
+ * @ltpmatchpollcounts: counter for link training pattern poll match
+ */
+struct xhdmirx_frl {
+	enum xhdmi_frltrainingstate trainingstate;
+	u32 timercnt;
+	u8 linerate;
+	u32 curfrlrate;
+	u8 lanes;
+	u8 ffelevels;
+	u8 ffesuppflag;
+	u8 fltupdateasserted;
+	union xhdmi_frlltp ltp;
+	union xhdmi_frlltp defaultltp;
+	union xhdmi_frlffeadjtype laneffeadjreq;
+	u8 fltnotimeout;
+	u8 fltnoretrain;
+	u8 ltpmatchwaitcounts;
+	u8 ltpmatchedcounts;
+	u8 ltpmatchpollcounts;
+};
+
+/*
+ * This is timeout period of LTS3 for different FFE levels (0 - 3)
+ * in milliseconds
+ */
+static const u16 frltimeoutlts3[4] = { 180, 90, 60, 45};
+
+/**
+ * struct xstream - Stream structure
+ * @video: video stream properties struct
+ * @frl: FRL related struct
+ * @state: streaming state
+ * @syncstatus: whether sync established or lost
+ * @pixelclk: Pixel clock
+ * @refclk: Reference clock from cable
+ * @cable_connected: Flag if HDMI cable is connected
+ * @isscrambled: Flag if stream is scrambled
+ * @vic: AVI vic code
+ * @getvidproptries: Number of tries to get video properties
+ * @ishdmi: whether hdmi or dvi
+ * @isfrl: FRL flag. 1 - FRL mode 0 - TMDS mode
+ */
+struct xstream {
+	struct xvideostream video;
+	struct xhdmirx_frl frl;
+	enum xhdmirx_stream_state state;
+	enum xhdmirx_syncstatus syncstatus;
+	u32 pixelclk;
+	u32 refclk;
+	bool cable_connected;
+	bool isscrambled;
+	u8 vic;
+	u8 getvidproptries;
+	u8 ishdmi;
+	u8 isfrl;
+};
+
+union xhdmi_auxheader {
+	u32 data;
+	u8 byte[4];
+};
+
+union xhdmi_auxdata {
+	u32 data[8];
+	u8 byte[32];
+};
+
+struct xhdmi_aux {
+	union xhdmi_auxheader header;
+	union xhdmi_auxdata data;
+};
+
+/**
+ * struct xhdmirx_state - HDMI Rx driver state
+ * @dev: Platform structure
+ * @regs: Base address
+ * @sd: V4L2 subdev structure
+ * @pad: Media pad
+ * @mbus_fmt: Detected media bus format
+ * @dv_timings: Detected DV timings
+ * @stream: struct to save stream properties
+ * @aux: struct to save auxiliary packet
+ * @xhdmi_mutex: Mutex to prevent concurrent access to state structure
+ * @work_queue: Pointer to work queue for hot plug
+ * @delayed_work_enable_hotplug: Delayed work to enable hotplug
+ * @phy: array of phy structure pointers
+ * @clks: array of clocks
+ * @frlclkfreqkhz: FRL Clock Freq in KHz
+ * @vidclkfreqkhz: Video Clock Freq in KHz
+ * @intrstatus: Array to save the interrupt status registers
+ * @edid_user: User EDID
+ * @edid_user_blocks: Number of blocks in user EDID
+ * @edid_blocks_max: Max number of EDID blocks
+ * @edid_ram_size: EDID RAM size in IP configuration
+ * @max_ppc: Maximum input pixels per clock from IP configuration
+ * @max_bpc: Maximum bit per component from IP configuration
+ * @max_frl_rate: Maximum FRL rate supported from IP configuration
+ * @hdmi_stream_up: hdmi stream is up or not
+ * @isstreamup: flag whether stream is up
+ */
+struct xhdmirx_state {
+	struct device *dev;
+	void __iomem *regs;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_mbus_framefmt mbus_fmt;
+	struct v4l2_dv_timings dv_timings;
+	struct xstream stream;
+	struct xhdmi_aux aux;
+	/* mutex to prevent concurrent access to this structure */
+	struct mutex xhdmi_mutex;
+	struct workqueue_struct *work_queue;
+	struct delayed_work delayed_work_enable_hotplug;
+	struct phy *phy[XHDMI_MAX_LANES];
+	struct clk_bulk_data *clks;
+	u32 frlclkfreqkhz;
+	u32 vidclkfreqkhz;
+	u32 intrstatus[8];
+	u8 *edid_user;
+	int edid_user_blocks;
+	int edid_blocks_max;
+	u16 edid_ram_size;
+	u8 max_ppc;
+	u8 max_bpc;
+	u8 max_frl_rate;
+	u8 hdmi_stream_up;
+	bool isstreamup;
+};
+
+static const char * const xhdmirx_clks[] = {
+	"s_axi_cpu_aclk", "frl_clk", "s_axis_video_aclk",
+};
+
+/*
+ * 187, 255 offset need to be updated for bandwidth and no. of lanes
+ * 12 Gbps @ 4 lanes => [187] = 0x63, [255] = 0x94
+ * 10 Gbps @ 4 lanes => [187] = 0x53, [255] = 0xA4
+ *  8 Gbps @ 4 lanes => [187] = 0x43, [255] = 0xB4
+ *  6 Gbps @ 4 lanes => [187] = 0x33, [255] = 0xC4
+ *  6 Gbps @ 3 lanes => [187] = 0x23, [255] = 0xD4
+ *  3 Gbps @ 4 lanes => [187] = 0x13, [255] = 0xE4
+ *  TMDS             => [187] = 0x03, [255] = 0xF4
+ */
+static const u8 xilinx_frl_edid[] = {
+	0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00,
+	0x61, 0x98, 0x34, 0x12, 0x78, 0x56, 0x34, 0x12,
+	0x17, 0x1D, 0x01, 0x03, 0x80, 0xA0, 0x5A, 0x78,
+	0x0A, 0xEE, 0x91, 0xA3, 0x54, 0x4C, 0x99, 0x26,
+	0x0F, 0x50, 0x54, 0x21, 0x00, 0x00, 0x01, 0x01,
+	0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
+	0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x08, 0xE8,
+	0x00, 0x30, 0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58,
+	0x8A, 0x00, 0x20, 0xC2, 0x31, 0x00, 0x00, 0x1E,
+	0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
+	0x58, 0x2C, 0x45, 0x00, 0x20, 0xC2, 0x31, 0x00,
+	0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x18,
+	0x90, 0x0F, 0x8C, 0x3C, 0x00, 0x0A, 0x20, 0x20,
+	0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
+	0x00, 0x58, 0x49, 0x4C, 0x49, 0x4E, 0x58, 0x20,
+	0x48, 0x44, 0x4D, 0x49, 0x32, 0x31, 0x01, 0x53,
+
+	0x02, 0x03, 0x44, 0xF1, 0x56, 0xC4, 0xC3, 0xC2,
+	0xD4, 0xD3, 0xD2, 0xC1, 0x7F, 0x7E, 0x7D, 0xDB,
+	0xDA, 0x66, 0x65, 0x76, 0x75, 0x61, 0x60, 0x3F,
+	0x40, 0x10, 0x1F, 0x2C, 0x0F, 0x7F, 0x07, 0x5F,
+	0x7C, 0x01, 0x57, 0x06, 0x03, 0x67, 0x7E, 0x03,
+	0x6B, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38, 0x3C,
+	0x20, 0x00, 0x20, 0x03, 0x67, 0xD8, 0x5D, 0xC4,
+	0x01, 0x78, 0x80, 0x63, 0xE4, 0x0F, 0x09, 0xCC,
+	0x00, 0xE2, 0x00, 0xCF, 0x08, 0xE8, 0x00, 0x30,
+	0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58, 0x8A, 0x00,
+	0x20, 0xC2, 0x31, 0x00, 0x00, 0x1E, 0x04, 0x74,
+	0x00, 0x30, 0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58,
+	0x8A, 0x00, 0x20, 0xC2, 0x31, 0x00, 0x00, 0x1E,
+	0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
+	0x58, 0x2C, 0x45, 0x00, 0x20, 0xC2, 0x31, 0x00,
+	0x00, 0x1E, 0x00, 0x00, 0x00, 0x00, 0x00, 0x94
+};
+
+/* Event struct */
+static const struct v4l2_event xhdmi_ev_fmt = {
+	.type = V4L2_EVENT_SOURCE_CHANGE,
+	.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
+};
+
+#define xhdmirx_piointr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_CTRL_CLR_OFFSET,\
+		    HDMIRX_PIO_CTRL_IE_MASK)
+#define xhdmirx_piointr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_CTRL_SET_OFFSET,\
+		    HDMIRX_PIO_CTRL_IE_MASK)
+
+#define xhdmirx_pio_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_CTRL_CLR_OFFSET,\
+		    HDMIRX_PIO_CTRL_RUN_MASK)
+#define xhdmirx_pio_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_CTRL_SET_OFFSET,\
+		    HDMIRX_PIO_CTRL_RUN_MASK)
+
+#define xhdmirx_tmr1_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR1_CTRL_RUN_MASK)
+#define xhdmirx_tmr1_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR1_CTRL_RUN_MASK)
+#define xhdmirx_tmr1intr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR1_CTRL_IE_MASK)
+#define xhdmirx_tmr1intr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR1_CTRL_IE_MASK)
+#define xhdmirx_tmr1_start(xhdmi, value) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_1_CNT_OFFSET, \
+		    value)
+#define xhdmirx_tmr1_getval(xhdmi) xhdmi_read(xhdmi, HDMIRX_TMR_1_CNT_OFFSET)
+
+#define xhdmirx_tmr2_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR2_CTRL_RUN_MASK)
+#define xhdmirx_tmr2_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR2_CTRL_RUN_MASK)
+#define xhdmirx_tmr2intr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR2_CTRL_IE_MASK)
+#define xhdmirx_tmr2intr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR2_CTRL_IE_MASK)
+#define xhdmirx_tmr2_start(xhdmi, value) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_2_CNT_OFFSET, \
+		    value)
+#define xhdmirx_tmr2_getval(xhdmi) xhdmi_read(xhdmi, HDMIRX_TMR_2_CNT_OFFSET)
+
+#define xhdmirx_tmr3_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR3_CTRL_RUN_MASK)
+#define xhdmirx_tmr3_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR3_CTRL_RUN_MASK)
+#define xhdmirx_tmr3intr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR3_CTRL_IE_MASK)
+#define xhdmirx_tmr3intr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR3_CTRL_IE_MASK)
+#define xhdmirx_tmr3_start(xhdmi, value) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_3_CNT_OFFSET, \
+		    value)
+#define xhdmirx_tmr3_getval(xhdmi) xhdmi_read(xhdmi, HDMIRX_TMR_3_CNT_OFFSET)
+
+#define xhdmirx_tmr4_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR4_CTRL_RUN_MASK)
+#define xhdmirx_tmr4_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR4_CTRL_RUN_MASK)
+#define xhdmirx_tmr4intr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_SET_OFFSET, \
+		    HDMIRX_TMR4_CTRL_IE_MASK)
+#define xhdmirx_tmr4intr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_CTRL_CLR_OFFSET, \
+		    HDMIRX_TMR4_CTRL_IE_MASK)
+#define xhdmirx_tmr4_start(xhdmi, value) \
+	xhdmi_write(xhdmi, HDMIRX_TMR_4_CNT_OFFSET, \
+		    value)
+#define xhdmirx_tmr4_getval(xhdmi) xhdmi_read(xhdmi, HDMIRX_TMR_4_CNT_OFFSET)
+
+#define xhdmirx_vtdintr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_VTD_CTRL_CLR_OFFSET, \
+		    HDMIRX_VTD_CTRL_IE_MASK)
+#define xhdmirx_vtdintr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_VTD_CTRL_SET_OFFSET, \
+		    HDMIRX_VTD_CTRL_IE_MASK)
+#define xhdmirx_vtd_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_VTD_CTRL_CLR_OFFSET, \
+		    HDMIRX_VTD_CTRL_RUN_MASK)
+#define xhdmirx_vtd_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_VTD_CTRL_SET_OFFSET, \
+		    HDMIRX_VTD_CTRL_RUN_MASK)
+
+#define xhdmirx_ddcintr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_CLR_OFFSET, \
+		    HDMIRX_DDC_CTRL_IE_MASK)
+#define xhdmirx_ddcintr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_SET_OFFSET, \
+		    HDMIRX_DDC_CTRL_IE_MASK)
+#define xhdmirx_ddc_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_CLR_OFFSET, \
+		    HDMIRX_DDC_CTRL_RUN_MASK)
+#define xhdmirx_ddc_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_SET_OFFSET, \
+		    HDMIRX_DDC_CTRL_RUN_MASK)
+
+#define xhdmirx_auxintr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUX_CTRL_CLR_OFFSET, \
+		    HDMIRX_AUX_CTRL_IE_MASK)
+#define xhdmirx_auxintr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUX_CTRL_SET_OFFSET, \
+		    HDMIRX_AUX_CTRL_IE_MASK)
+#define xhdmirx_aux_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUX_CTRL_CLR_OFFSET, \
+		    HDMIRX_AUX_CTRL_RUN_MASK)
+#define xhdmirx_aux_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUX_CTRL_SET_OFFSET, \
+		    HDMIRX_AUX_CTRL_RUN_MASK)
+
+#define xhdmirx_audintr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUD_CTRL_CLR_OFFSET, \
+		    HDMIRX_AUD_CTRL_IE_MASK)
+#define xhdmirx_audintr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUD_CTRL_SET_OFFSET, \
+		    HDMIRX_AUD_CTRL_IE_MASK)
+#define xhdmirx_aud_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUD_CTRL_CLR_OFFSET, \
+		    HDMIRX_AUD_CTRL_RUN_MASK)
+#define xhdmirx_aud_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_AUD_CTRL_SET_OFFSET, \
+		    HDMIRX_AUD_CTRL_RUN_MASK)
+
+#define xhdmirx_lnkstaintr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_LNKSTA_CTRL_CLR_OFFSET, \
+		    HDMIRX_LNKSTA_CTRL_IE_MASK)
+#define xhdmirx_lnkstaintr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_LNKSTA_CTRL_SET_OFFSET, \
+		    HDMIRX_LNKSTA_CTRL_IE_MASK)
+#define xhdmirx_lnksta_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_LNKSTA_CTRL_CLR_OFFSET, \
+		    HDMIRX_LNKSTA_CTRL_RUN_MASK)
+#define xhdmirx_lnksta_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_LNKSTA_CTRL_SET_OFFSET, \
+		    HDMIRX_LNKSTA_CTRL_RUN_MASK)
+
+#define xhdmirx_frlintr_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_CLR_OFFSET, \
+		    HDMIRX_FRL_CTRL_IE_MASK)
+#define xhdmirx_frlintr_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_SET_OFFSET, \
+		    HDMIRX_FRL_CTRL_IE_MASK)
+#define xhdmirx_frl_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_SET_OFFSET, \
+		    HDMIRX_FRL_CTRL_RSTN_MASK)
+#define xhdmirx_frl_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_CLR_OFFSET, \
+		    HDMIRX_FRL_CTRL_RSTN_MASK)
+
+#define xhdmirx_setfrl_vclkvckeratio(xhdmi, val) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_VCLK_VCKE_RATIO_OFFSET, val)
+
+#define xhdmirx_skewlockevt_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_SET_OFFSET, \
+		    HDMIRX_FRL_CTRL_SKEW_EVT_EN_MASK)
+
+#define xhdmirx_skewlockevt_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_CLR_OFFSET, \
+		    HDMIRX_FRL_CTRL_SKEW_EVT_EN_MASK)
+
+#define xhdmirx_ddcscdc_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_SET_OFFSET, \
+		    HDMIRX_DDC_CTRL_SCDC_EN_MASK)
+
+#define xhdmirx_rxcore_vrst_assert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_INT_VRST_MASK)
+#define xhdmirx_rxcore_vrst_deassert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_INT_VRST_MASK)
+
+#define xhdmirx_rxcore_lrst_assert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_INT_LRST_MASK)
+#define xhdmirx_rxcore_lrst_deassert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_INT_LRST_MASK)
+
+#define xhdmirx_sysrst_assert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_EXT_SYSRST_MASK)
+#define xhdmirx_sysrst_deassert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_EXT_SYSRST_MASK)
+
+#define xhdmirx_ext_vrst_assert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_EXT_VRST_MASK)
+#define xhdmirx_ext_vrst_deassert(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_EXT_VRST_MASK)
+
+#define xhdmirx_link_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_LNK_EN_MASK)
+
+#define xhdmirx_link_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_LNK_EN_MASK)
+
+#define xhdmirx_video_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_VID_EN_MASK)
+
+#define xhdmirx_video_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_VID_EN_MASK)
+
+#define xhdmirx_axi4s_enable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET, \
+		    HDMIRX_PIO_OUT_AXIS_EN_MASK)
+
+#define xhdmirx_axi4s_disable(xhdmi) \
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET, \
+		    HDMIRX_PIO_OUT_AXIS_EN_MASK)
+
+static void xhdmi_execfrlstate(struct xhdmirx_state *xhdmi);
+
+static inline u32 xhdmi_read(struct xhdmirx_state *xhdmi, u32 addr)
+{
+	return ioread32(xhdmi->regs + addr);
+}
+
+static inline void xhdmi_write(struct xhdmirx_state *xhdmi,
+			       u32 addr, u32 val)
+{
+	iowrite32(val, xhdmi->regs + addr);
+}
+
+static inline struct xhdmirx_state *to_xhdmirx_state(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xhdmirx_state, sd);
+}
+
+static inline u32 xhdmi_getfrlactivepixratio(struct xhdmirx_state *xhdmi)
+{
+	return xhdmi_read(xhdmi, HDMIRX_FRL_RATIO_ACT_OFFSET);
+}
+
+static inline u32 xhdmi_getfrltotalpixratio(struct xhdmirx_state *xhdmi)
+{
+	return xhdmi_read(xhdmi, HDMIRX_FRL_RATIO_TOT_OFFSET);
+}
+
+static u32 xhdmi_getpatternsmatchstatus(struct xhdmirx_state *xhdmi)
+{
+	u32 data = xhdmi_read(xhdmi, HDMIRX_FRL_STA_OFFSET);
+
+	return FIELD_GET(HDMIRX_FRL_STA_FLT_PM_ALLL_MASK, data);
+}
+
+/**
+ * xhdmirx_vtd_settimebase - Set the Video Timing Detector
+ *
+ * @xhdmi: pointer to driver state
+ * @count: count value to set the timer to.
+ */
+static inline void xhdmirx_vtd_settimebase(struct xhdmirx_state *xhdmi, u32 count)
+{
+	u32 val = xhdmi_read(xhdmi, HDMIRX_VTD_CTRL_OFFSET);
+
+	val &= ~HDMIRX_VTD_CTRL_TIMERBASE_MASK;
+	val |= FIELD_PREP(HDMIRX_VTD_CTRL_TIMERBASE_MASK, count);
+	xhdmi_write(xhdmi, HDMIRX_VTD_CTRL_OFFSET, val);
+}
+
+static u32 xhdmi_frlddcreadfield(struct xhdmirx_state *xhdmi, enum xhdmi_frlscdcfieldtype field)
+{
+	u32 data = 0xFFFFFFFF;
+	int i;
+
+	for (i = 0; i < MAX_FRL_RETRY; i++) {
+		data = xhdmi_read(xhdmi, HDMIRX_FRL_SCDC_OFFSET);
+		if (data & HDMIRX_FRL_SCDC_RDY_MASK)
+			break;
+	}
+
+	if (!(data & HDMIRX_FRL_SCDC_RDY_MASK)) {
+		dev_dbg_ratelimited(xhdmi->dev, "%s - scdc is not ready!", __func__);
+		return data;
+	}
+
+	data = HDMIRX_FRL_SCDC_ADDR_MASK & frlscdcfield[field].offset;
+	data |=	HDMIRX_FRL_SCDC_RD_MASK;
+
+	xhdmi_write(xhdmi, HDMIRX_FRL_SCDC_OFFSET, data);
+
+	for (i = 0; i < MAX_FRL_RETRY; i++) {
+		data = xhdmi_read(xhdmi, HDMIRX_FRL_SCDC_OFFSET);
+		if (data & HDMIRX_FRL_SCDC_RDY_MASK) {
+			data = data >> HDMIRX_FRL_SCDC_DAT_SHIFT;
+			return ((data >> frlscdcfield[field].shift) &
+				frlscdcfield[field].mask);
+		}
+	}
+
+	dev_dbg_ratelimited(xhdmi->dev, "%s - failed!", __func__);
+	return 0xFFFFFFFF;
+}
+
+static int xhdmi_frlddcwritefield(struct xhdmirx_state *xhdmi,
+				  enum xhdmi_frlscdcfieldtype field,
+				  u8 value)
+{
+	/* 256 byte FIFO but doubling to 512 tries for safety */
+	u32 data = 0, retrycount = 2 * MAX_FRL_RETRY;
+
+	if (frlscdcfield[field].mask != 0xFF)
+		data = xhdmi_frlddcreadfield(xhdmi, field);
+
+	if (data == 0xFFFFFFFF)
+		return -EINVAL;
+
+	do {
+		data = xhdmi_read(xhdmi, HDMIRX_FRL_SCDC_OFFSET);
+	} while (!(data & HDMIRX_FRL_SCDC_RDY_MASK) && retrycount--);
+
+	if (!retrycount)
+		return -EBUSY;
+
+	if (frlscdcfield[field].mask != 0xFF) {
+		data &= ~((frlscdcfield[field].mask <<
+			   frlscdcfield[field].shift) <<
+			  HDMIRX_FRL_SCDC_DAT_SHIFT);
+	} else {
+		data &= ~((u32)(HDMIRX_FRL_SCDC_DAT_MASK <<
+				HDMIRX_FRL_SCDC_DAT_SHIFT));
+	}
+
+	data &= ~((u32)HDMIRX_FRL_SCDC_ADDR_MASK);
+
+	data |= (((value & frlscdcfield[field].mask) <<
+		frlscdcfield[field].shift) <<
+		HDMIRX_FRL_SCDC_DAT_SHIFT) |
+		(frlscdcfield[field].offset & HDMIRX_FRL_SCDC_ADDR_MASK) |
+		HDMIRX_FRL_SCDC_WR_MASK;
+
+	xhdmi_write(xhdmi, HDMIRX_FRL_SCDC_OFFSET, data);
+
+	data = xhdmi_frlddcreadfield(xhdmi, field);
+	if (data != value) {
+		dev_err_ratelimited(xhdmi->dev, "field %u to write %u != written value %u",
+				    field, value, data);
+	}
+
+	return 0;
+}
+
+static inline void xhdmirx_scrambler_enable(struct xhdmirx_state *xhdmi)
+{
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET,
+		    HDMIRX_PIO_OUT_SCRM_MASK);
+	xhdmi->stream.isscrambled = true;
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_SCRAMBLER_STAT, 1);
+}
+
+static inline void xhdmirx_scrambler_disable(struct xhdmirx_state *xhdmi)
+{
+	xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET,
+		    HDMIRX_PIO_OUT_SCRM_MASK);
+	xhdmi->stream.isscrambled = false;
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_SCRAMBLER_STAT, 0);
+}
+
+static inline void xhdmirx_ddcscdc_clear(struct xhdmirx_state *xhdmi)
+{
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_SET_OFFSET,
+		    HDMIRX_DDC_CTRL_SCDC_CLR_MASK);
+	/* 50 ms sleep as this will be needed by IP core to clear FIFO */
+	usleep_range(50, 100);
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_CLR_OFFSET,
+		    HDMIRX_DDC_CTRL_SCDC_CLR_MASK);
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FLT_READY, 1);
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_SINK_VER, 1);
+}
+
+/**
+ * xhdmirx_disable_allintr - Disable all the interrupt sources
+ *
+ * @xhdmi: pointer to driver state
+ */
+static void xhdmirx_disable_allintr(struct xhdmirx_state *xhdmi)
+{
+	xhdmirx_piointr_disable(xhdmi);
+	xhdmirx_vtdintr_disable(xhdmi);
+	xhdmirx_ddcintr_disable(xhdmi);
+	xhdmirx_tmr1intr_disable(xhdmi);
+	xhdmirx_tmr2intr_disable(xhdmi);
+	xhdmirx_tmr3intr_disable(xhdmi);
+	xhdmirx_tmr4intr_disable(xhdmi);
+	xhdmirx_auxintr_disable(xhdmi);
+	xhdmirx_audintr_disable(xhdmi);
+	xhdmirx_frlintr_disable(xhdmi);
+	xhdmirx_lnkstaintr_disable(xhdmi);
+}
+
+/**
+ * xhdmirx_enable_allintr - Enable all the interrupt sources
+ *
+ * @xhdmi: pointer to driver state
+ */
+static void xhdmirx_enable_allintr(struct xhdmirx_state *xhdmi)
+{
+	xhdmirx_piointr_enable(xhdmi);
+	xhdmirx_vtdintr_enable(xhdmi);
+	xhdmirx_ddcintr_enable(xhdmi);
+	xhdmirx_tmr1intr_enable(xhdmi);
+	xhdmirx_tmr2intr_enable(xhdmi);
+	xhdmirx_tmr3intr_enable(xhdmi);
+	xhdmirx_tmr4intr_enable(xhdmi);
+	xhdmirx_auxintr_enable(xhdmi);
+	xhdmirx_frlintr_enable(xhdmi);
+	xhdmirx_lnkstaintr_enable(xhdmi);
+}
+
+/**
+ * xhdmirx1_bridgeyuv420 - Enable/disable YUV 420 in bridge
+ *
+ * @xhdmi: pointer to driver state
+ * @flag: Flag to set or clear the bit
+ */
+static void xhdmirx1_bridgeyuv420(struct xhdmirx_state *xhdmi, bool flag)
+{
+	if (flag)
+		xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET,
+			    HDMIRX_PIO_OUT_BRIDGE_YUV420_MASK);
+	else
+		xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET,
+			    HDMIRX_PIO_OUT_BRIDGE_YUV420_MASK);
+}
+
+/**
+ * xhdmirx1_bridgepixeldrop - Enable/Disable pixel drop in bridge
+ *
+ * @xhdmi: pointer to driver state
+ * @flag: Flag to set or clear
+ */
+static void xhdmirx1_bridgepixeldrop(struct xhdmirx_state *xhdmi, bool flag)
+{
+	if (flag)
+		xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET,
+			    HDMIRX_PIO_OUT_BRIDGE_PIXEL_MASK);
+	else
+		xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET,
+			    HDMIRX_PIO_OUT_BRIDGE_PIXEL_MASK);
+}
+
+/**
+ * xhdmirx1_start - Start the HDMI Rx by enabling the PIO
+ *
+ * @xhdmi: pointer to driver state
+ */
+static void xhdmirx1_start(struct xhdmirx_state *xhdmi)
+{
+	xhdmirx_pio_enable(xhdmi);
+	xhdmirx_piointr_enable(xhdmi);
+}
+
+static void xhdmirx1_clearlinkstatus(struct xhdmirx_state *xhdmi)
+{
+	xhdmi_write(xhdmi, HDMIRX_LNKSTA_CTRL_SET_OFFSET, HDMIRX_LNKSTA_CTRL_ERR_CLR_MASK);
+	xhdmi_write(xhdmi, HDMIRX_LNKSTA_CTRL_CLR_OFFSET, HDMIRX_LNKSTA_CTRL_ERR_CLR_MASK);
+}
+
+/**
+ * xhdmirx_set_hpd - Toggle hot plug detect line
+ * @xhdmi: pointer to driver state
+ * @enable: Flag to assert or deassert the HPD line
+ *
+ * This function is used to toggle hot plug detect line to indicate to the
+ * HDMI Tx about change in HDMI Rx.
+ */
+static void xhdmirx_set_hpd(struct xhdmirx_state *xhdmi, int enable)
+{
+	if (enable)
+		xhdmi_write(xhdmi, HDMIRX_PIO_OUT_SET_OFFSET,
+			    HDMIRX_PIO_OUT_HPD_MASK);
+	else
+		xhdmi_write(xhdmi, HDMIRX_PIO_OUT_CLR_OFFSET,
+			    HDMIRX_PIO_OUT_HPD_MASK);
+}
+
+static inline bool xhdmirx1_isstreamconnected(struct xhdmirx_state *xhdmi)
+{
+	/* return the stream cable connected */
+	return xhdmi->stream.cable_connected;
+}
+
+/**
+ * xhdmirx1_gettmdsclkratio - Get the TMDS clock ratio
+ * @xhdmi: pointer to the driver state
+ *
+ * Return: TMDS clock ratio 0 or 1
+ */
+static u32 xhdmirx1_gettmdsclkratio(struct xhdmirx_state *xhdmi)
+{
+	u32 val;
+
+	val = xhdmi_read(xhdmi, HDMIRX_PIO_IN_OFFSET);
+	val = FIELD_GET(HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK, val);
+
+	dev_dbg(xhdmi->dev, "Get TMDS Clk Ratio = %u\n", val);
+	return val;
+}
+
+/**
+ * xhdmirx1_getavi_vic - Get the HDMI VIC id
+ * @xhdmi: pointer to driver state
+ *
+ * Return: Returns HDMI VIC id
+ */
+static u8 xhdmirx1_getavi_vic(struct xhdmirx_state *xhdmi)
+{
+	u32 val;
+
+	val = xhdmi_read(xhdmi, HDMIRX_AUX_STA_OFFSET);
+	val = FIELD_GET(HDMIRX_AUX_STA_AVI_VIC_MASK, val);
+
+	dev_dbg_ratelimited(xhdmi->dev, "Get AVI VIC = %u\n", val);
+	return (u8)val;
+}
+
+/**
+ * xhdmirx1_getavi_colorspace - Get the colorspace of the incoming stream
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Returns: Colorspace of stream
+ */
+static enum xcolorspace xhdmirx1_getavi_colorspace(struct xhdmirx_state *xhdmi)
+{
+	u32 val;
+	enum xcolorspace cs;
+
+	dev_dbg_ratelimited(xhdmi->dev, "Get avi colorspace ");
+	val = xhdmi_read(xhdmi, HDMIRX_AUX_STA_OFFSET);
+	switch (FIELD_GET(HDMIRX_AUX_STA_AVI_CS_MASK, val)) {
+	case 1:
+		cs = XCS_YUV422;
+		dev_dbg_ratelimited(xhdmi->dev, "YUV 422\n");
+		break;
+	case 2:
+		cs = XCS_YUV444;
+		dev_dbg_ratelimited(xhdmi->dev, "YUV 444\n");
+		break;
+	case 3:
+		cs = XCS_YUV420;
+		dev_dbg_ratelimited(xhdmi->dev, "YUV 420\n");
+		break;
+	default:
+		cs = XCS_RGB;
+		dev_dbg_ratelimited(xhdmi->dev, "RGB\n");
+		break;
+	}
+
+	return cs;
+}
+
+/**
+ * xhdmirx1_getgcp_colordepth - Get the color depth of the stream
+ *
+ * @xhdmi: pointer to the driver state
+ *
+ * Returns: colordepth or bits per component of incoming stream
+ */
+static enum xcolordepth xhdmirx1_getgcp_colordepth(struct xhdmirx_state *xhdmi)
+{
+	u32 val;
+	enum xcolordepth ret;
+
+	val = xhdmi_read(xhdmi, HDMIRX_AUX_STA_OFFSET);
+	switch (FIELD_GET(HDMIRX_AUX_STA_GCP_CD_MASK, val)) {
+	case 1:
+		ret = XCD_10;
+		break;
+	case 2:
+		ret = XCD_12;
+		break;
+	case 3:
+		ret = XCD_16;
+		break;
+	default:
+		ret = XCD_8;
+		break;
+	}
+
+	dev_dbg_ratelimited(xhdmi->dev, "get GCP colordepth %u\n", ret);
+
+	return ret;
+}
+
+/**
+ * xhdmirx1_get_video_properties - Get the incoming video stream properties
+ *
+ * @xhdmi: pointer to the driver state
+ *
+ * This function populates the video structure with color space and depth.
+ * If getvidproptries > MAX_VID_PROP_TRIES means incoming stream is DVI
+ *
+ * Returns: 0 on success or -1 on fail
+ */
+static int xhdmirx1_get_video_properties(struct xhdmirx_state *xhdmi)
+{
+	u32 status;
+
+	status = xhdmi_read(xhdmi, HDMIRX_AUX_STA_OFFSET);
+
+	if (status & HDMIRX_AUX_STA_AVI_MASK) {
+		xhdmi->stream.video.colorspace = xhdmirx1_getavi_colorspace(xhdmi);
+		xhdmi->stream.vic = xhdmirx1_getavi_vic(xhdmi);
+
+		if (xhdmi->stream.video.colorspace == XCS_YUV422)
+			xhdmi->stream.video.colordepth = XCD_12;
+		else
+			xhdmi->stream.video.colordepth =
+				xhdmirx1_getgcp_colordepth(xhdmi);
+		return 0;
+	}
+
+	if (xhdmi->stream.getvidproptries > MAX_VID_PROP_TRIES) {
+		xhdmi->stream.video.colorspace = XCS_RGB;
+		xhdmi->stream.vic = 0;
+		xhdmi->stream.video.colordepth = XCD_8;
+		return 0;
+	}
+
+	xhdmi->stream.getvidproptries++;
+	return -1;
+}
+
+/**
+ * xhdmirx1_get_vid_timing - Get the video timings of incoming stream
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function gets the timing information from the IP and checks it
+ * against the older value. If mismatch, it updates the video timing
+ * structure in the driver state.
+ *
+ * Returns: 0 on success or -1 on fail
+ */
+static int xhdmirx1_get_vid_timing(struct xhdmirx_state *xhdmi)
+{
+	u32 data;
+	u16 hact, hfp, hsw, hbp, htot;
+	u16 vact, vfp[MAX_FIELDS], vsw[MAX_FIELDS], vbp[MAX_FIELDS];
+	u16 vtot[MAX_FIELDS];
+	u8 match, yuv420_correction, isinterlaced;
+
+	if (xhdmi->stream.video.colorspace == XCS_YUV420)
+		yuv420_correction = 2;
+	else
+		yuv420_correction = 1;
+
+	htot = xhdmi_read(xhdmi, HDMIRX_VTD_TOT_PIX_OFFSET) * yuv420_correction;
+	hact = xhdmi_read(xhdmi, HDMIRX_VTD_ACT_PIX_OFFSET) * yuv420_correction;
+	hsw = xhdmi_read(xhdmi, HDMIRX_VTD_HSW_OFFSET) * yuv420_correction;
+	hfp = xhdmi_read(xhdmi, HDMIRX_VTD_HFP_OFFSET) * yuv420_correction;
+	hbp = xhdmi_read(xhdmi, HDMIRX_VTD_HBP_OFFSET) * yuv420_correction;
+
+	data = xhdmi_read(xhdmi, HDMIRX_VTD_TOT_LIN_OFFSET);
+	vtot[0] = FIELD_GET(HDMIRX_VTD_VF0_MASK, data);
+	vtot[1] = FIELD_GET(HDMIRX_VTD_VF1_MASK, data);
+
+	vact = xhdmi_read(xhdmi, HDMIRX_VTD_ACT_LIN_OFFSET);
+
+	data = xhdmi_read(xhdmi, HDMIRX_VTD_VFP_OFFSET);
+	vfp[0] = FIELD_GET(HDMIRX_VTD_VF0_MASK, data);
+	vfp[1] = FIELD_GET(HDMIRX_VTD_VF1_MASK, data);
+
+	data = xhdmi_read(xhdmi, HDMIRX_VTD_VSW_OFFSET);
+	vsw[0] = FIELD_GET(HDMIRX_VTD_VF0_MASK, data);
+	vsw[1] = FIELD_GET(HDMIRX_VTD_VF1_MASK, data);
+
+	data = xhdmi_read(xhdmi, HDMIRX_VTD_VBP_OFFSET);
+	vbp[0] = FIELD_GET(HDMIRX_VTD_VF0_MASK, data);
+	vbp[1] = FIELD_GET(HDMIRX_VTD_VF1_MASK, data);
+
+	data = xhdmi_read(xhdmi, HDMIRX_VTD_STA_OFFSET);
+	if (data & HDMIRX_VTD_STA_FMT_MASK)
+		isinterlaced = 1;
+	else
+		isinterlaced = 0;
+
+	match = 1;
+
+	if (!hact || !hfp || !hsw || !hbp || !htot || !vact ||
+	    !vtot[0] || !vfp[0] || !vbp[0] || !vsw[0])
+		match = 0;
+
+	if (isinterlaced && (!vfp[1] || !vsw[1] || !vbp[1] || !vtot[1]))
+		match = 0;
+
+	if (hact != xhdmi->stream.video.timing.hact ||
+	    htot != xhdmi->stream.video.timing.htot ||
+	    hfp != xhdmi->stream.video.timing.hfp ||
+	    hbp != xhdmi->stream.video.timing.hbp ||
+	    hsw != xhdmi->stream.video.timing.hsw ||
+	    vact != xhdmi->stream.video.timing.vact ||
+	    vtot[0] != xhdmi->stream.video.timing.vtot[0] ||
+	    vtot[1] != xhdmi->stream.video.timing.vtot[1] ||
+	    vfp[0] != xhdmi->stream.video.timing.vfp[0] ||
+	    vfp[1] != xhdmi->stream.video.timing.vfp[1] ||
+	    vbp[0] != xhdmi->stream.video.timing.vbp[0] ||
+	    vbp[1] != xhdmi->stream.video.timing.vbp[1] ||
+	    vsw[0] != xhdmi->stream.video.timing.vsw[0] ||
+	    vsw[1] != xhdmi->stream.video.timing.vsw[1])
+		match = 0;
+
+	if (vtot[0] != (vact + vfp[0] + vsw[0] + vbp[0]))
+		match = 0;
+
+	if (isinterlaced) {
+		if (vtot[1] != (vact + vfp[1] + vsw[1] + vbp[1]))
+			match = 0;
+	} else {
+		/* if field 1 is populated for progessive video */
+		if (vfp[1] | vbp[1] | vsw[1])
+			match = 0;
+	}
+
+	xhdmi->stream.video.timing.hact = hact;
+	xhdmi->stream.video.timing.htot = htot;
+	xhdmi->stream.video.timing.hfp = hfp;
+	xhdmi->stream.video.timing.hsw = hsw;
+	xhdmi->stream.video.timing.hbp = hbp;
+
+	xhdmi->stream.video.timing.vtot[0] = vtot[0];
+	xhdmi->stream.video.timing.vtot[1] = vtot[1];
+
+	xhdmi->stream.video.timing.vact = vact;
+	xhdmi->stream.video.timing.vfp[0] = vfp[0];
+	xhdmi->stream.video.timing.vfp[1] = vfp[1];
+	xhdmi->stream.video.timing.vsw[0] = vsw[0];
+	xhdmi->stream.video.timing.vsw[1] = vsw[1];
+	xhdmi->stream.video.timing.vbp[0] = vbp[0];
+	xhdmi->stream.video.timing.vbp[1] = vbp[1];
+
+	if (match) {
+		data = xhdmi_read(xhdmi, HDMIRX_VTD_STA_OFFSET);
+
+		if (data & HDMIRX_VTD_STA_FMT_MASK)
+			xhdmi->stream.video.isinterlaced = true;
+		else
+			xhdmi->stream.video.isinterlaced = false;
+
+		if (data & HDMIRX_VTD_STA_VS_POL_MASK)
+			xhdmi->stream.video.timing.vsyncpol = 1;
+		else
+			xhdmi->stream.video.timing.vsyncpol = 0;
+
+		if (data & HDMIRX_VTD_STA_HS_POL_MASK)
+			xhdmi->stream.video.timing.hsyncpol = 1;
+		else
+			xhdmi->stream.video.timing.hsyncpol = 0;
+
+		return 0;
+	}
+
+	return -1;
+}
+
+/**
+ * xhdmirx1_setpixelclk - Calculate and save the pixel clock
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function calculates the pixel clock based on incoming stream
+ * reference clock and bits per component / color depth
+ */
+static void xhdmirx1_setpixelclk(struct xhdmirx_state *xhdmi)
+{
+	switch (xhdmi->stream.video.colordepth) {
+	case XCD_10:
+		xhdmi->stream.pixelclk = (xhdmi->stream.refclk << 2) / 5;
+		break;
+	case XCD_12:
+		xhdmi->stream.pixelclk = (xhdmi->stream.refclk << 1) / 3;
+		break;
+	case XCD_16:
+		xhdmi->stream.pixelclk = xhdmi->stream.refclk >> 1;
+		break;
+	default:
+		xhdmi->stream.pixelclk = xhdmi->stream.refclk;
+		break;
+	}
+
+	if (xhdmi->stream.video.colorspace == XCS_YUV422)
+		xhdmi->stream.pixelclk = xhdmi->stream.refclk;
+
+	dev_dbg(xhdmi->dev, "pixel clk = %u Hz ref clk = %u Hz\n",
+		xhdmi->stream.pixelclk, xhdmi->stream.refclk);
+}
+
+static int xhdmirx_phy_configure(struct xhdmirx_state *xhdmi,
+				 union phy_configure_opts *opts)
+{
+	int ret, i;
+
+	for (i = 0; i < XHDMI_MAX_LANES; i++) {
+		ret = phy_configure(xhdmi->phy[i], opts);
+		if (ret) {
+			dev_err(xhdmi->dev, "phy_configure error %d\n", ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static void phy_rxinit_cb(void *param)
+{
+	struct xhdmirx_state *xhdmi = (struct xhdmirx_state *)param;
+	union phy_configure_opts opts = {0};
+	u32 val;
+
+	/* Get TMDS clock ratio */
+	val = xhdmirx1_gettmdsclkratio(xhdmi);
+
+	opts.hdmi.tmdsclock_ratio_flag = 1;
+	opts.hdmi.tmdsclock_ratio = val;
+
+	/* set the TMDS clock ratio in phy */
+	xhdmirx_phy_configure(xhdmi, &opts);
+	dev_dbg(xhdmi->dev, "Phy RxInitCallback tmds clk ratio = %u\n", val);
+}
+
+static void phy_rxready_cb(void *param)
+{
+	struct xhdmirx_state *xhdmi = (struct xhdmirx_state *)param;
+	union phy_configure_opts opts = {0};
+	int ret;
+
+	opts.hdmi.rx_get_refclk = 1;
+	ret = xhdmirx_phy_configure(xhdmi, &opts);
+	if (ret) {
+		dev_err(xhdmi->dev, "Unable to get ref clk from phy %d\n", ret);
+		return;
+	}
+
+	xhdmi->stream.refclk = opts.hdmi.rx_refclk_hz;
+
+	/*
+	 * In case the TMDS Clock ratio is 1/40, the reference clock must be
+	 * compensated.
+	 */
+	if (xhdmirx1_gettmdsclkratio(xhdmi))
+		xhdmi->stream.refclk *= 4;
+
+	dev_dbg(xhdmi->dev, "Phy RxReadyCallback refclk = %u Hz\n", xhdmi->stream.refclk);
+}
+
+/**
+ * xhdmirx1_configbridgemode - Configure the bridge
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function configure the bridge for YUV420 and pixel drop
+ * based on whether the stream in interlaced, hdmi and colorspace is YUV420
+ */
+static void xhdmirx1_configbridgemode(struct xhdmirx_state *xhdmi)
+{
+	if (!xhdmi->stream.ishdmi && xhdmi->stream.video.isinterlaced) {
+		if (xhdmi->stream.video.timing.hact == 1440 &&
+		    (xhdmi->stream.video.timing.vact == 288 ||
+		     xhdmi->stream.video.timing.vact == 240)) {
+			xhdmirx1_bridgeyuv420(xhdmi, false);
+			xhdmirx1_bridgepixeldrop(xhdmi, true);
+		}
+	}
+
+	/* check aux info frame for pixel repetition and return */
+	if (xhdmi->stream.video.colorspace == XCS_YUV420) {
+		xhdmirx1_bridgepixeldrop(xhdmi, false);
+		xhdmirx1_bridgeyuv420(xhdmi, true);
+	} else {
+		/*
+		 * check if pixel repetition factor is 2
+		 * for ntsc pal support
+		 */
+		xhdmirx1_bridgeyuv420(xhdmi, false);
+		xhdmirx1_bridgepixeldrop(xhdmi, false);
+	}
+}
+
+/**
+ * xhdmirx1_get_mbusfmtcode - Update the media bus format
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function populates the media bus format in the mbus_fmt struct
+ * based on the colorspace and colordepth of the incoming stream.
+ */
+static void xhdmirx1_get_mbusfmtcode(struct xhdmirx_state *xhdmi)
+{
+	struct xvideostream *stream = &xhdmi->stream.video;
+
+	/* decode AVI Info frame and fill up above correctly */
+	switch (stream->colorspace) {
+	case XCS_YUV422:
+		switch (xhdmi->max_bpc) {
+		case XCD_8:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_UYVY8_1X16;
+			break;
+		case XCD_10:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_UYVY10_1X20;
+			break;
+		case XCD_12:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_UYVY12_1X24;
+			break;
+		case XCD_16:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_UYVY16_2X32;
+			break;
+		}
+		break;
+	case XCS_YUV444:
+		switch (xhdmi->max_bpc) {
+		case XCD_8:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_VUY8_1X24;
+			break;
+		case XCD_10:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_VUY10_1X30;
+			break;
+		case XCD_12:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_VUY12_1X36;
+			break;
+		case XCD_16:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_VUY16_1X48;
+			break;
+		}
+		break;
+	case XCS_YUV420:
+		switch (xhdmi->max_bpc) {
+		case XCD_8:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_VYYUYY8_1X24;
+			break;
+		case XCD_10:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_VYYUYY10_4X20;
+			break;
+		case XCD_12:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_UYYVYY12_4X24;
+			break;
+		case XCD_16:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_UYYVYY16_4X32;
+			break;
+		}
+		break;
+	case XCS_RGB:
+		switch (xhdmi->max_bpc) {
+		case XCD_8:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_RBG888_1X24;
+			break;
+		case XCD_10:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_RBG101010_1X30;
+			break;
+		case XCD_12:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_RBG121212_1X36;
+			break;
+		case XCD_16:
+			xhdmi->mbus_fmt.code = MEDIA_BUS_FMT_RBG161616_1X48;
+			break;
+		}
+		break;
+	}
+	dev_dbg_ratelimited(xhdmi->dev, "mbus_fmt code = 0x%08x\n",
+			    xhdmi->mbus_fmt.code);
+}
+
+/**
+ * rxstreamup - Update the dv timings and media bus format structs
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function is called when the stream is found to be up.
+ * This configures the bridge mode, media bus format struct, detected
+ * dv timings and generates source change event to user space.
+ */
+static void rxstreamup(struct xhdmirx_state *xhdmi)
+{
+	struct xvideostream *stream;
+
+	xhdmirx1_clearlinkstatus(xhdmi);
+	xhdmi->isstreamup = true;
+
+	xhdmirx1_configbridgemode(xhdmi);
+
+	/* enable clock forwarding */
+	stream = &xhdmi->stream.video;
+
+	/*
+	 * use v4l2_find_dv_timings_cea861_vic with avi info frame vic id
+	 * to get the std timings. For now we will get timing from IP.
+	 */
+	xhdmi->mbus_fmt.width = stream->timing.hact;
+	xhdmi->mbus_fmt.height = stream->timing.vact;
+
+	/*
+	 * For pixel repetition cases 1440x240@60,120,240 or
+	 * 1440x288@50,100,200, make width as half.
+	 */
+	if (stream->timing.hact == 1440 &&
+	    ((stream->timing.vact == 240 && (stream->framerate == 60 ||
+					     stream->framerate == 120 ||
+					     stream->framerate == 240)) ||
+	     (stream->timing.vact == 288 && (stream->framerate == 50 ||
+					     stream->framerate == 100 ||
+					     stream->framerate == 200))))
+		xhdmi->mbus_fmt.width /= 2;
+
+	if (stream->isinterlaced)
+		xhdmi->mbus_fmt.field = V4L2_FIELD_ALTERNATE;
+	else
+		xhdmi->mbus_fmt.field = V4L2_FIELD_NONE;
+
+	xhdmi->mbus_fmt.colorspace = V4L2_COLORSPACE_REC709;
+	xhdmi->mbus_fmt.ycbcr_enc = V4L2_YCBCR_ENC_709;
+	xhdmi->mbus_fmt.xfer_func = V4L2_XFER_FUNC_709;
+	xhdmi->mbus_fmt.quantization = V4L2_QUANTIZATION_DEFAULT;
+
+	xhdmirx1_get_mbusfmtcode(xhdmi);
+
+	xhdmi->dv_timings.type		= V4L2_DV_BT_656_1120;
+	xhdmi->dv_timings.bt.width	= stream->timing.hact;
+	xhdmi->dv_timings.bt.height	= stream->timing.vact;
+	xhdmi->dv_timings.bt.interlaced = !!stream->isinterlaced;
+	if (xhdmi->dv_timings.bt.interlaced)
+		xhdmi->dv_timings.bt.height *= 2;
+
+	xhdmi->dv_timings.bt.polarities = stream->timing.vsyncpol ?
+					  V4L2_DV_VSYNC_POS_POL : 0;
+	xhdmi->dv_timings.bt.polarities |= stream->timing.hsyncpol ?
+					   V4L2_DV_HSYNC_POS_POL : 0;
+	/* determine pixel clock */
+	xhdmi->dv_timings.bt.pixelclock = xhdmi->stream.pixelclk;
+
+	/*
+	 * Double pixel clock for YUV 420 TMDS / Tri-band packing
+	 * as per Sec 7.1 of HDMI 2.1 spec.
+	 */
+	if (xhdmi->stream.video.colorspace == XCS_YUV420)
+		xhdmi->dv_timings.bt.pixelclock *= 2;
+
+	if (stream->timing.hact == 1440 &&
+	    ((stream->timing.vact == 240 && (stream->framerate == 60 ||
+					     stream->framerate == 120 ||
+					     stream->framerate == 240)) ||
+	     (stream->timing.vact == 288 && (stream->framerate == 50 ||
+					     stream->framerate == 100 ||
+					     stream->framerate == 200)))) {
+		xhdmirx1_bridgeyuv420(xhdmi, false);
+		xhdmirx1_bridgepixeldrop(xhdmi, true);
+	}
+
+	xhdmi->dv_timings.bt.hfrontporch = stream->timing.hfp;
+	xhdmi->dv_timings.bt.hsync = stream->timing.hsw;
+	xhdmi->dv_timings.bt.hbackporch = stream->timing.hbp;
+	xhdmi->dv_timings.bt.vfrontporch = stream->timing.vfp[0];
+	xhdmi->dv_timings.bt.vsync = stream->timing.vsw[0];
+	xhdmi->dv_timings.bt.vbackporch = stream->timing.vbp[0];
+	xhdmi->dv_timings.bt.il_vfrontporch = stream->timing.vfp[1];
+	xhdmi->dv_timings.bt.il_vsync = stream->timing.vsw[1];
+	xhdmi->dv_timings.bt.il_vbackporch = stream->timing.vbp[1];
+	xhdmi->dv_timings.bt.standards = V4L2_DV_BT_STD_CEA861;
+	xhdmi->dv_timings.bt.flags = V4L2_DV_FL_IS_CE_VIDEO;
+
+	xhdmi->isstreamup = true;
+
+	v4l2_subdev_notify_event(&xhdmi->sd, &xhdmi_ev_fmt);
+
+	dev_dbg_ratelimited(xhdmi->dev, "mbus fmt width = %u height = %u code = 0x%08x\n",
+			    xhdmi->mbus_fmt.width, xhdmi->mbus_fmt.height, xhdmi->mbus_fmt.code);
+#ifdef DEBUG
+	v4l2_print_dv_timings("xilinx-hdmi-rx", "", &xhdmi->dv_timings, 1);
+#endif
+}
+
+/**
+ * rxstreaminit - Initialise the stream
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function is called to initialized the video phy
+ */
+static void rxstreaminit(struct xhdmirx_state *xhdmi)
+{
+	union phy_configure_opts cfg = {0};
+	struct xvideostream *vidstream = &xhdmi->stream.video;
+	u8 colordepth = (u8)xhdmi->stream.video.colordepth;
+
+	if (vidstream->colorspace == XCS_YUV422)
+		colordepth = (u8)XCD_8;
+
+	cfg.hdmi.ppc = COREPIXPERCLK;
+	cfg.hdmi.bpc = colordepth;
+	cfg.hdmi.cal_mmcm_param = 1;
+	xhdmirx_phy_configure(xhdmi, &cfg);
+}
+
+/**
+ * rxconnect - function called back in connect state
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function is called when driver state is in connect state.
+ * When the cable is connected / disconnected this function is called.
+ */
+static void rxconnect(struct xhdmirx_state *xhdmi)
+{
+	union phy_configure_opts phy_cfg = {0};
+
+	dev_dbg_ratelimited(xhdmi->dev, "%s - enter cable %s\n",
+			    __func__, xhdmi->stream.cable_connected ?
+			    "connected" : "disconnected");
+
+	if (xhdmirx1_isstreamconnected(xhdmi)) {
+		xhdmirx_set_hpd(xhdmi, 1);
+		phy_cfg.hdmi.ibufds = 1;
+		phy_cfg.hdmi.ibufds_en = 1;
+		xhdmirx_phy_configure(xhdmi, &phy_cfg);
+		xhdmirx_ext_vrst_assert(xhdmi);
+	} else {
+		xhdmirx_set_hpd(xhdmi, 0);
+		xhdmirx_scrambler_disable(xhdmi);
+
+		phy_cfg.hdmi.tmdsclock_ratio_flag = 1;
+		phy_cfg.hdmi.tmdsclock_ratio = 0;
+		xhdmirx_phy_configure(xhdmi, &phy_cfg);
+
+		phy_cfg.hdmi.ibufds = 1;
+		phy_cfg.hdmi.ibufds_en = 0;
+		xhdmirx_phy_configure(xhdmi, &phy_cfg);
+	}
+}
+
+/**
+ * tmdsconfig - Function to config the TMDS in the phy
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Function is used to configure the Phy in TMDS 2.0 or HDMI 2.1 config
+ */
+static void tmdsconfig(struct xhdmirx_state *xhdmi)
+{
+	union phy_configure_opts phy_cfg = {0};
+
+	phy_cfg.hdmi.config_hdmi20 = 1;
+	xhdmirx_phy_configure(xhdmi, &phy_cfg);
+	xhdmirx_setfrl_vclkvckeratio(xhdmi, 0);
+	dev_dbg_ratelimited(xhdmi->dev, "Set HDMI 2.0 phy");
+}
+
+static void frlconfig(struct xhdmirx_state *xhdmi)
+{
+	union phy_configure_opts phy_cfg = {0};
+	u64 linerate = xhdmi->stream.frl.linerate * (u64)(1e9);
+	u8 nchannels = xhdmi->stream.frl.lanes;
+
+	phy_cfg.hdmi.linerate = linerate;
+	phy_cfg.hdmi.nchannels = nchannels;
+	phy_cfg.hdmi.config_hdmi21 = 1;
+	xhdmirx_phy_configure(xhdmi, &phy_cfg);
+	dev_dbg_ratelimited(xhdmi->dev, "Set HDMI 2.1 phy");
+}
+
+static void phyresetcb(struct xhdmirx_state *xhdmi)
+{
+	union phy_configure_opts opts = {0};
+
+	xhdmi->stream.frl.ltpmatchpollcounts = 0;
+	xhdmi->stream.frl.ltpmatchwaitcounts = 0;
+
+	opts.hdmi.reset_gt = true;
+	xhdmirx_phy_configure(xhdmi, &opts);
+}
+
+/**
+ * streamdown - called on stream down event
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * This function is called on stream down event
+ */
+static void streamdown(struct xhdmirx_state *xhdmi)
+{
+	dev_dbg_ratelimited(xhdmi->dev, "%s - enter\n", __func__);
+
+	/* In TMDS mode */
+	if (!xhdmi->stream.isfrl) {
+		xhdmirx_rxcore_vrst_assert(xhdmi);
+		xhdmirx_rxcore_lrst_assert(xhdmi);
+	}
+	xhdmirx_sysrst_assert(xhdmi);
+	xhdmi->isstreamup = false;
+}
+
+static void xhdmirx1_clear(struct xhdmirx_state *xhdmi)
+{
+	/*
+	 * reset state to XSTREAM_DOWN
+	 * reset colorspace, depth, timing, ishdmi, isfrl, isinterlaced, vic
+	 * reset getvidpropcount, set frl state as lts_l
+	 * clear aux packet data
+	 * reset audio properties
+	 */
+	xhdmi->stream.state = XSTREAM_DOWN;
+	xhdmi->stream.ishdmi = false;
+	xhdmi->isstreamup = false;
+
+	xhdmi->stream.video.colorspace = XCS_RGB;
+	xhdmi->stream.video.isinterlaced = false;
+	xhdmi->stream.video.colordepth = XCD_8;
+	memset(&xhdmi->stream.video.timing, 0, sizeof(xhdmi->stream.video.timing));
+	xhdmi->stream.vic = 0;
+	xhdmi->stream.getvidproptries = 0;
+	memset(&xhdmi->dv_timings, 0, sizeof(xhdmi->dv_timings));
+	memset(&xhdmi->mbus_fmt, 0, sizeof(xhdmi->mbus_fmt));
+
+	xhdmi->stream.isfrl = false;
+	xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_L;
+
+	streamdown(xhdmi);
+}
+
+static int xhdmi_retrievefrlratelanes(struct xhdmirx_state *xhdmi)
+{
+	u32 data;
+	int ret = 0;
+
+	data = xhdmi_frlddcreadfield(xhdmi, XSCDCFIELD_FRL_RATE);
+	xhdmi->stream.frl.curfrlrate = data;
+
+	switch (data) {
+	case 6:
+		xhdmi->stream.frl.linerate = 12;
+		xhdmi->stream.frl.lanes = 4;
+		break;
+	case 5:
+		xhdmi->stream.frl.linerate = 10;
+		xhdmi->stream.frl.lanes = 4;
+		break;
+	case 4:
+		xhdmi->stream.frl.linerate = 8;
+		xhdmi->stream.frl.lanes = 4;
+		break;
+	case 3:
+		xhdmi->stream.frl.linerate = 6;
+		xhdmi->stream.frl.lanes = 4;
+		break;
+	case 2:
+		xhdmi->stream.frl.linerate = 6;
+		xhdmi->stream.frl.lanes = 3;
+		break;
+	case 1:
+		xhdmi->stream.frl.linerate = 3;
+		xhdmi->stream.frl.lanes = 3;
+		break;
+	default:
+		xhdmi->stream.frl.linerate = 0;
+		xhdmi->stream.frl.lanes = 0;
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+static u32 xhdmi_getfrlltpdetection(struct xhdmirx_state *xhdmi, u8 lane)
+{
+	u32 data = 0;
+
+	if (lane < XHDMI_MAX_LANES)
+		data = xhdmi_frlddcreadfield(xhdmi, XSCDCFIELD_LN0_LTP_REQ + lane);
+	else
+		dev_dbg(xhdmi->dev, "RX:ERROR, Wrong lane is selected to get!");
+
+	return data;
+}
+
+static void xhdmi_setfrlltpdetection(struct xhdmirx_state *xhdmi, u8 lane,
+				     enum xhdmi_frlltptype ltp)
+{
+	u32 value = (u32)ltp;
+
+	if (lane < XHDMI_MAX_LANES)
+		xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_LN0_LTP_REQ + lane, value);
+	else
+		dev_dbg(xhdmi->dev, "RX:ERROR, Wrong lane is selected to set!");
+}
+
+static void xhdmi_frlfltupdate(struct xhdmirx_state *xhdmi, bool flag)
+{
+	u8 data = flag ? 1 : 0;
+
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FLT_UPDATE, data);
+	xhdmi->stream.frl.fltupdateasserted = flag;
+}
+
+static void xhdmi_resetfrlltpdetection(struct xhdmirx_state *xhdmi)
+{
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_SET_OFFSET, HDMIRX_FRL_CTRL_FLT_CLR_MASK);
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_CLR_OFFSET, HDMIRX_FRL_CTRL_FLT_CLR_MASK);
+}
+
+static void xhdmi_clearfrlltp(struct xhdmirx_state *xhdmi)
+{
+	u8 lanes;
+
+	for (lanes = 0; lanes < XHDMI_MAX_LANES; lanes++) {
+		xhdmi_setfrlltpdetection(xhdmi, lanes, XLTP_RATE_CHANGE);
+		xhdmi_resetfrlltpdetection(xhdmi);
+	}
+}
+
+static void xhdmi_setfrlltpthreshold(struct xhdmirx_state *xhdmi, u8 threshold)
+{
+	u32 data;
+
+	data = xhdmi_read(xhdmi, HDMIRX_FRL_CTRL_OFFSET);
+	data &= (~(u32)HDMIRX_FRL_CTRL_FLT_THRES_MASK);
+	data |= FIELD_PREP(HDMIRX_FRL_CTRL_FLT_THRES_MASK, threshold);
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_OFFSET, data);
+}
+
+static int xhdmi_configfrlltpdetection(struct xhdmirx_state *xhdmi)
+{
+	u32 data, configuredltp = 0;
+
+	data = xhdmi->stream.frl.fltupdateasserted;
+
+	/* flt_update not cleared */
+	if (data)
+		return -EINVAL;
+
+	/* check if source has read and cleared flt_update, false = cleared */
+	if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_RATE_CH &&
+	    xhdmi->stream.frl.curfrlrate > xhdmi->max_frl_rate) {
+		data = true;
+	} else if (xhdmi->stream.frl.curfrlrate <= xhdmi->max_frl_rate) {
+		u8 ln;
+
+		for (ln = 0; ln < XHDMI_MAX_LANES; ln++) {
+			configuredltp = xhdmi_getfrlltpdetection(xhdmi, ln);
+
+			/*
+			 * if the lane was previously configured as 0xe, it needs to be
+			 * configured back to the ltp to resume link training.
+			 */
+			if (configuredltp == 0xE) {
+				xhdmi->stream.frl.ltp.byte[ln] =
+					xhdmi->stream.frl.defaultltp.byte[ln];
+			}
+
+			/* check if the ltp data requires updating */
+			if (configuredltp != xhdmi->stream.frl.ltp.byte[ln]) {
+				xhdmi_setfrlltpdetection(xhdmi, ln,
+							 xhdmi->stream.frl.ltp.byte[ln]);
+				data = true;
+			}
+		}
+	}
+
+	/* no updates are made */
+	if (!data)
+		return -ENODATA;
+
+	dev_dbg(xhdmi->dev, "rx: ltpreq: %x %x %x %x",
+		xhdmi->stream.frl.ltp.byte[0], xhdmi->stream.frl.ltp.byte[1],
+		xhdmi->stream.frl.ltp.byte[2], xhdmi->stream.frl.ltp.byte[3]);
+
+	dev_dbg(xhdmi->dev, "assert flt_update (%d)",
+		xhdmirx_tmr1_getval(xhdmi));
+
+	xhdmi_frlfltupdate(xhdmi, true);
+	xhdmi_resetfrlltpdetection(xhdmi);
+	return 0;
+}
+
+static void xhdmi_setfrlratewrevent_en(struct xhdmirx_state *xhdmi)
+{
+	xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_SET_OFFSET,
+		    HDMIRX_FRL_CTRL_FRL_RATE_WR_EVT_EN_MASK);
+}
+
+static void xhdmi_frlreset(struct xhdmirx_state *xhdmi, u8 reset)
+{
+	if (reset) {
+		xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_CLR_OFFSET,
+			    HDMIRX_FRL_CTRL_RSTN_MASK);
+		xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_SINK_VER, 1);
+		xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_SCRAMBLER_EN, 0);
+	} else {
+		xhdmi_write(xhdmi, HDMIRX_FRL_CTRL_SET_OFFSET,
+			    HDMIRX_FRL_CTRL_RSTN_MASK);
+		xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FRL_RATE, 0);
+	}
+}
+
+static void xhdmirx_tmrstartms(struct xhdmirx_state *xhdmi, u32 milliseconds,
+			       u8 timerselect)
+{
+	u32 clockcycles = 0;
+
+	if (milliseconds)
+		clockcycles = AXILITE_FREQ / (1000 / milliseconds);
+
+	switch (timerselect) {
+	case 1:
+		xhdmirx_tmr1_start(xhdmi, clockcycles);
+		break;
+	case 2:
+		xhdmirx_tmr2_start(xhdmi, clockcycles);
+		break;
+	case 3:
+		xhdmirx_tmr3_start(xhdmi, clockcycles);
+		break;
+	case 4:
+		xhdmirx_tmr4_start(xhdmi, clockcycles);
+		break;
+	}
+}
+
+static void xhdmi_setfrltimer(struct xhdmirx_state *xhdmi, u32 milliseconds)
+{
+	/* frl uses timer1 */
+	xhdmirx_tmrstartms(xhdmi, milliseconds, 1);
+}
+
+static void xhdmi_phyresetpoll(struct xhdmirx_state *xhdmi)
+{
+	u8 data = xhdmi_getpatternsmatchstatus(xhdmi);
+
+	/* Polls every 4ms */
+	xhdmirx_tmrstartms(xhdmi, 4, 3);
+
+	/*
+	 * One or more lanes are patterns matched but the remaining
+	 * lanes failed to patterns matched within 4ms or no patterns
+	 * have been matched for up to 12ms, proceed to reset Phy
+	 */
+	if (xhdmi->stream.frl.ltpmatchwaitcounts >= 1 ||
+	    xhdmi->stream.frl.ltpmatchpollcounts >= 3) {
+		phyresetcb(xhdmi);
+		return;
+	}
+
+	/* Increments the wait counter */
+	xhdmi->stream.frl.ltpmatchpollcounts++;
+
+	/* If LTP on some of the lanes are successfully matched */
+	if (data && data !=
+		(xhdmi->stream.frl.lanes == 3 ? 0x7 : 0xf)) {
+		xhdmi->stream.frl.ltpmatchwaitcounts++;
+	}
+}
+
+static void xhdmirx_execfrlstate_ltsl(struct xhdmirx_state *xhdmi)
+{
+	dev_dbg(xhdmi->dev, "RX: LTS:L");
+
+	/* Clear HDMI variables */
+	xhdmirx1_clear(xhdmi);
+
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FLT_READY, 1);
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FRL_RATE, 0);
+
+	tmdsconfig(xhdmi);
+	/* FrlLtsLCallback is just a logging function */
+}
+
+static void xhdmirx_execfrlstate_lts2(struct xhdmirx_state *xhdmi)
+{
+	dev_dbg(xhdmi->dev, "RX: LTS:2");
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FLT_READY, 1);
+}
+
+static void xhdmirx_execfrlstate_lts3_ratechange(struct xhdmirx_state *xhdmi)
+{
+	int status;
+
+	xhdmi->stream.frl.timercnt = 0;
+	status = xhdmi_retrievefrlratelanes(xhdmi);
+
+	if (xhdmi->stream.frl.ffesuppflag)
+		xhdmi->stream.frl.ffelevels =
+			xhdmi_frlddcreadfield(xhdmi, XSCDCFIELD_FFE_LEVELS);
+	else
+		xhdmi->stream.frl.ffelevels = 0;
+
+	dev_dbg(xhdmi->dev, "RX: LTS:3 Rate Change");
+	/* FrlLts3Callback is just logging function */
+	xhdmi_frlfltupdate(xhdmi, false);
+
+	if (!status && xhdmi->stream.frl.linerate) {
+		int i;
+
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3_RATE_CH;
+		xhdmi->stream.state = XSTATE_FRL_LINK_TRAININIG;
+		xhdmi->stream.isfrl = true;
+		xhdmi->stream.ishdmi = true;
+		dev_dbg(xhdmi->dev, "RX: Rate: %d Lanes: %d Ffe_lvl: %d",
+			xhdmi->stream.frl.linerate, xhdmi->stream.frl.lanes,
+			xhdmi->stream.frl.ffelevels);
+
+		xhdmirx_rxcore_lrst_assert(xhdmi);
+		xhdmirx_rxcore_vrst_assert(xhdmi);
+		xhdmirx_ext_vrst_assert(xhdmi);
+		xhdmirx_sysrst_assert(xhdmi);
+
+		xhdmirx_vtd_disable(xhdmi);
+		xhdmi_resetfrlltpdetection(xhdmi);
+		xhdmi_clearfrlltp(xhdmi);
+		xhdmi_setfrltimer(xhdmi, frltimeoutlts3[xhdmi->stream.frl.ffelevels]);
+
+		for (i = 0; i < XHDMI_MAX_LANES; i++)
+			xhdmi->stream.frl.ltp.byte[i] =
+				xhdmi->stream.frl.defaultltp.byte[i];
+
+		xhdmi->stream.frl.ltpmatchedcounts = 0;
+		xhdmi->stream.frl.ltpmatchwaitcounts = 0;
+		xhdmi->stream.frl.ltpmatchpollcounts = 0;
+
+		frlconfig(xhdmi);
+
+		/* set a 4 ms on Timer 3 for PhyReset callback */
+		xhdmirx_tmr3_enable(xhdmi);
+		xhdmirx_tmrstartms(xhdmi, 4, 3);
+	} else {
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_L;
+		xhdmi_execfrlstate(xhdmi);
+		xhdmi->stream.state = XSTREAM_DOWN;
+	}
+}
+
+static void xhdmirx_execfrlstate_lts3_ltpdetected(struct xhdmirx_state *xhdmi)
+{
+	u8 data;
+
+	dev_dbg(xhdmi->dev, "RX: LTS:3 LTP Detected %d",
+		xhdmirx_tmr1_getval(xhdmi));
+
+	/* Make sure phy is reset at least once after the pattterns have matched */
+	if (!xhdmi->stream.frl.ltpmatchedcounts) {
+		xhdmi->stream.frl.ltpmatchedcounts++;
+		xhdmi->stream.frl.ltpmatchpollcounts = 0;
+		xhdmi->stream.frl.ltpmatchwaitcounts = 0;
+
+		phyresetcb(xhdmi);
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3;
+
+		dev_dbg(xhdmi->dev, "%s - fail", __func__);
+		return;
+	}
+
+	data = xhdmi_getpatternsmatchstatus(xhdmi);
+
+	if ((xhdmi->stream.frl.lanes == 3 ? 0x7 : 0xF) == data) {
+		/* disable timer 3 which triggers Phy reset */
+		xhdmirx_tmrstartms(xhdmi, 0, 3);
+		xhdmirx_tmr3_disable(xhdmi);
+
+		/* 0 = Link Training Passing */
+		xhdmi->stream.frl.ltp.data = 0x0;
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3_RDY;
+
+		/* FrlLtsPCallback is only a logging function */
+		dev_dbg(xhdmi->dev, "LTP_DET:MATCH");
+	} else {
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3;
+		dev_dbg(xhdmi->dev, "LTP_DET:FALSE:%x", data);
+	}
+}
+
+static void xhdmirx_execfrlstate_lts3_timer(struct xhdmirx_state *xhdmi)
+{
+	u8 data = xhdmi_getpatternsmatchstatus(xhdmi);
+
+	xhdmi->stream.frl.fltnoretrain =
+		xhdmi_frlddcreadfield(xhdmi, XSCDCFIELD_FLT_NO_RETRAIN);
+	xhdmi->stream.frl.timercnt = frltimeoutlts3[xhdmi->stream.frl.ffelevels];
+
+	if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P) {
+		dev_dbg(xhdmi->dev, "RX: LTS:P Lts3_Timer OUT FFE_LVL: %d",
+			xhdmi->stream.frl.ffelevels);
+	}
+
+	if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3 ||
+	    xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_TMR ||
+	    xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_RATE_CH ||
+	    xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_RDY) {
+		if (!xhdmi->stream.frl.fltnotimeout && !xhdmi->stream.frl.fltnoretrain) {
+			if (xhdmi->stream.frl.timercnt >
+			    (frltimeoutlts3[xhdmi->stream.frl.ffelevels] *
+			     xhdmi->stream.frl.ffelevels)) {
+				/* If LTPs are not detected on all active lanes */
+				if ((xhdmi->stream.frl.lanes == 3 ? 0x7 : 0xF) != data) {
+					/* Stop the timer which will initiate phy reset */
+					xhdmirx_tmrstartms(xhdmi, 0, 3);
+					xhdmi->stream.frl.ltp.byte[0] = 0xF;
+					xhdmi->stream.frl.ltp.byte[1] = 0xF;
+					xhdmi->stream.frl.ltp.byte[2] = 0xF;
+					xhdmi->stream.frl.ltp.byte[3] = 0xF;
+					/* FrlLts4Callback is just logging function */
+				}
+			} else if (xhdmi->stream.frl.ffesuppflag) {
+				u8 lanes;
+
+				for (lanes = 0; lanes < xhdmi->stream.frl.lanes; lanes++) {
+					/* if any lane is not passing by link training */
+					if (((data >> lanes) & 0x1) != 0x1) {
+						/* 0xE = Request to change TxFFE */
+						xhdmi->stream.frl.ltp.byte[lanes] = 0xE;
+						dev_dbg(xhdmi->dev, "RX: %d:0xE", lanes);
+					}
+				}
+				xhdmi_resetfrlltpdetection(xhdmi);
+				xhdmi_setfrltimer(xhdmi,
+						  frltimeoutlts3[xhdmi->stream.frl.ffelevels]);
+			}
+		}
+	}
+
+	if (xhdmi->stream.frl.trainingstate != XFRLSTATE_LTS_3_RDY)
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3;
+}
+
+static void xhdmirx_execfrlstate_lts3(struct xhdmirx_state *xhdmi)
+{
+	int status;
+
+	dev_dbg(xhdmi->dev, "RX: LTS:3 %d", xhdmirx_tmr1_getval(xhdmi));
+	dev_dbg(xhdmi->dev, "scdc flt update = %d",
+		xhdmi_frlddcreadfield(xhdmi, XSCDCFIELD_FLT_UPDATE));
+
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FRL_START, 0);
+
+	status = xhdmi_configfrlltpdetection(xhdmi);
+	if (!status) {
+		if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_RDY) {
+			xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_P;
+			dev_dbg(xhdmi->dev, "RX: LTP Pass");
+			/* Disable timer */
+			xhdmi_setfrltimer(xhdmi, 0);
+			status = 0;
+		} else if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_TMR) {
+		} else if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3) {
+		} else {
+			dev_dbg(xhdmi->dev, " --->ELSE");
+		}
+		status = 0;
+	} else if (status == -EINVAL) {
+		/*
+		 * source has not cleared FLT_update so sink should not update
+		 * FLT_req and FLT_update as to ensure proper data handshake
+		 */
+		dev_dbg(xhdmi->dev, "RX: LTS_3-->FLT_UPDATE not Cleared %d",
+			xhdmirx_tmr1_getval(xhdmi));
+	} else {
+		/* case of -ENODATA */
+		/*
+		 * Source has cleared FLT_update but no update from sink is required
+		 */
+	}
+}
+
+static void xhdmirx_execfrlstate_ltsp(struct xhdmirx_state *xhdmi)
+{
+	dev_dbg(xhdmi->dev, "RX: LTS:P");
+
+	if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P_FRL_RDY &&
+	    !xhdmi->stream.frl.fltupdateasserted) {
+		dev_dbg(xhdmi->dev, "RX: LTS: P_FRL_RDY");
+		xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FRL_START, 1);
+		dev_dbg(xhdmi->dev, "RX: FRL_START");
+		/* FrlStartCallback is just logging function */
+	}
+}
+
+static void xhdmirx_execfrlstate_ltsp_timeout(struct xhdmirx_state *xhdmi)
+{
+	dev_dbg(xhdmi->dev, "rx: lts:p timeout");
+	tmdsconfig(xhdmi);
+}
+
+static void xhdmi_execfrlstate(struct xhdmirx_state *xhdmi)
+{
+	dev_dbg(xhdmi->dev, "Rx : LTS :%u", xhdmi->stream.frl.trainingstate);
+
+	switch (xhdmi->stream.frl.trainingstate) {
+	case XFRLSTATE_LTS_L:
+		xhdmirx_execfrlstate_ltsl(xhdmi);
+		dev_dbg(xhdmi->dev, "---LTSL:");
+		break;
+
+	case XFRLSTATE_LTS_2:
+		xhdmirx_execfrlstate_lts2(xhdmi);
+		break;
+
+	case XFRLSTATE_LTS_3_RATE_CH:
+		xhdmirx_execfrlstate_lts3_ratechange(xhdmi);
+		/* Note : With some sources such as Realtek, the execution
+		 * of LTS3 state can be removed to check if the system still
+		 * works.
+		 */
+		xhdmirx_execfrlstate_lts3(xhdmi);
+		break;
+
+	case XFRLSTATE_LTS_3_ARM_LNK_RDY:
+	case XFRLSTATE_LTS_3_ARM_VID_RDY:
+		break;
+
+	case XFRLSTATE_LTS_3_LTP_DET:
+		xhdmirx_execfrlstate_lts3_ltpdetected(xhdmi);
+		xhdmirx_execfrlstate_lts3(xhdmi);
+		break;
+
+	case XFRLSTATE_LTS_3_TMR:
+		xhdmirx_execfrlstate_lts3_timer(xhdmi);
+		xhdmirx_execfrlstate_lts3(xhdmi);
+		break;
+
+	case XFRLSTATE_LTS_3:
+	case XFRLSTATE_LTS_3_RDY:
+		xhdmirx_execfrlstate_lts3(xhdmi);
+		break;
+
+	case XFRLSTATE_LTS_P:
+	case XFRLSTATE_LTS_P_FRL_RDY:
+	case XFRLSTATE_LTS_P_VID_RDY:
+		xhdmirx_execfrlstate_ltsp(xhdmi);
+		break;
+
+	case XFRLSTATE_LTS_P_TIMEOUT:
+		xhdmirx_execfrlstate_ltsp_timeout(xhdmi);
+		break;
+
+	default:
+		dev_err(xhdmi->dev, "RX:S:FRL_INVALID_STATE(%u)!",
+			xhdmi->stream.frl.trainingstate);
+		break;
+	}
+}
+
+static int xhdmirx_frlmodeenable(struct xhdmirx_state *xhdmi, u8 ltpthreshold,
+				 union xhdmi_frlltp defaultltp, u8 ffesuppflag)
+{
+	int i;
+
+	if (ffesuppflag > 1) {
+		dev_err(xhdmi->dev, "ffesuppflag can be 0 or 1 and not %u", ffesuppflag);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < XHDMI_MAX_LANES; i++) {
+		if (defaultltp.byte[i] < XLTP_LFSR0 ||
+		    defaultltp.byte[i] > XLTP_LFSR3) {
+			if (i == 3 && !defaultltp.byte[i])
+				break;
+
+			dev_err(xhdmi->dev, "invalid ltp byte %u for lane %u",
+				defaultltp.byte[i], i);
+			return -EINVAL;
+		}
+	}
+
+	for (i = 0; i < XHDMI_MAX_LANES; i++)
+		xhdmi->stream.frl.defaultltp.byte[i] = defaultltp.byte[i];
+
+	xhdmi->stream.frl.ffesuppflag = ffesuppflag;
+
+	xhdmi_setfrlltpthreshold(xhdmi, ltpthreshold);
+	xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_2;
+
+	xhdmi_execfrlstate(xhdmi);
+
+	return 0;
+}
+
+/**
+ * xhdmirx_pioint_handler - Function to handle the PIO interrupt
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Function to handle the PIO interrupt
+ */
+static void xhdmirx_pioint_handler(struct xhdmirx_state *xhdmi)
+{
+	u32 event, data;
+
+	event = xhdmi_read(xhdmi, HDMIRX_PIO_IN_EVT_OFFSET);
+	/* clear the PIO interrupts */
+	xhdmi_write(xhdmi, HDMIRX_PIO_IN_EVT_OFFSET, event);
+	data = xhdmi_read(xhdmi, HDMIRX_PIO_IN_OFFSET);
+
+	dev_dbg_ratelimited(xhdmi->dev, "pio int handler PIO IN - 0x%08x\n",
+			    data);
+
+	/* handle cable connect / disconnect */
+	if (event & HDMIRX_PIO_IN_DET_MASK) {
+		if (data & HDMIRX_PIO_IN_DET_MASK) {
+			/* cable connected */
+			xhdmi->stream.cable_connected = true;
+			xhdmi_frlreset(xhdmi, false);
+			xhdmi->stream.ishdmi = false;
+			xhdmi->stream.isfrl = false;
+			rxconnect(xhdmi);
+			tmdsconfig(xhdmi);
+		} else {
+			xhdmi->stream.cable_connected = false;
+			xhdmirx_ddcscdc_clear(xhdmi);
+			/* reset frl as true */
+			xhdmi_frlreset(xhdmi, true);
+			rxconnect(xhdmi);
+		}
+	}
+
+	if (event & HDMIRX_PIO_IN_LNK_RDY_MASK) {
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG) {
+			if (data & HDMIRX_PIO_IN_LNK_RDY_MASK) {
+				switch (xhdmi->stream.frl.trainingstate) {
+				case XFRLSTATE_LTS_3_RATE_CH:
+					xhdmi->stream.frl.trainingstate =
+						XFRLSTATE_LTS_3_ARM_LNK_RDY;
+					break;
+				case XFRLSTATE_LTS_3_ARM_VID_RDY:
+					xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3;
+					xhdmi_execfrlstate(xhdmi);
+					break;
+				default:
+					/* Link Ready Error callback */
+					dev_dbg_ratelimited(xhdmi->dev, "LNK_RDY 1 Error %d",
+							    xhdmi->stream.frl.trainingstate);
+					break;
+				}
+			} else {
+				dev_dbg(xhdmi->dev, "LNK_RDY:0");
+			}
+		} else if (xhdmi->stream.isfrl) {
+			/* Link Ready Error callback */
+			dev_dbg_ratelimited(xhdmi->dev, "LNK_RDY during FRL Link");
+		} else {
+			dev_dbg_ratelimited(xhdmi->dev, "LNK_RDY TMDS");
+			xhdmi->stream.state = XSTREAM_IDLE;
+			dev_dbg_ratelimited(xhdmi->dev, "pio lnk rdy state = XSTREAM_IDLE");
+			/* start 10 ms timer */
+			xhdmirx_tmr1_start(xhdmi, TIME_10MS);
+		}
+	}
+
+	if (event & HDMIRX_PIO_IN_VID_RDY_MASK) {
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG) {
+			if (data & HDMIRX_PIO_IN_VID_RDY_MASK) {
+				switch (xhdmi->stream.frl.trainingstate) {
+				case XFRLSTATE_LTS_3_RATE_CH:
+					xhdmi->stream.frl.trainingstate =
+						XFRLSTATE_LTS_3_ARM_VID_RDY;
+					break;
+				case XFRLSTATE_LTS_3_ARM_LNK_RDY:
+					xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3;
+					xhdmi_execfrlstate(xhdmi);
+					break;
+				default:
+					/* video ready error */
+					dev_dbg_ratelimited(xhdmi->dev, "VID_RDY 1 Error! %d",
+							    xhdmi->stream.frl.trainingstate);
+					break;
+				}
+			} else {
+				dev_dbg_ratelimited(xhdmi->dev, "VID_RDY:0");
+			}
+		} else if (xhdmi->stream.isfrl) {
+			/* video ready error */
+			dev_err_ratelimited(xhdmi->dev, "VID_RDY during FRL Link fail!");
+		} else {
+			/* Ready */
+			if (data & HDMIRX_PIO_IN_VID_RDY_MASK) {
+				if (xhdmi->stream.state == XSTREAM_INIT) {
+					dev_dbg_ratelimited(xhdmi->dev, "pio vid rdy state = XSTREAM_INIT\n");
+					/* Toggle Rx Core reset */
+					xhdmirx_rxcore_vrst_assert(xhdmi);
+					xhdmirx_rxcore_vrst_deassert(xhdmi);
+
+					/* Toggle bridge reset */
+					xhdmirx_ext_vrst_assert(xhdmi);
+					xhdmirx_sysrst_assert(xhdmi);
+					xhdmirx_ext_vrst_deassert(xhdmi);
+					xhdmirx_sysrst_deassert(xhdmi);
+
+					xhdmi->stream.state = XSTREAM_ARM;
+					/* start 200 ms timer */
+					xhdmirx_tmr1_start(xhdmi, TIME_200MS);
+				}
+			} else {
+				/* Stream Down */
+				xhdmirx_rxcore_vrst_assert(xhdmi);
+				xhdmirx_rxcore_lrst_assert(xhdmi);
+
+				xhdmirx1_clear(xhdmi);
+
+				xhdmirx_aux_disable(xhdmi);
+				xhdmirx_aud_disable(xhdmi);
+				xhdmirx_vtd_disable(xhdmi);
+				xhdmirx_link_disable(xhdmi);
+				xhdmirx_video_enable(xhdmi);
+				xhdmirx_axi4s_disable(xhdmi);
+
+				xhdmi->stream.state = XSTREAM_DOWN;
+				dev_dbg_ratelimited(xhdmi->dev, "pio vid rdy state = XSTREAM_DOWN\n");
+
+				xhdmi_write(xhdmi, HDMIRX_VTD_CTRL_CLR_OFFSET,
+					    HDMIRX_VTD_CTRL_SYNC_LOSS_MASK);
+
+				streamdown(xhdmi);
+				xhdmi->hdmi_stream_up = 0;
+			}
+		}
+	}
+
+	if (event & HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK) {
+		dev_dbg_ratelimited(xhdmi->dev, "scrambler intr\n");
+		if (data & HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK)
+			xhdmirx_scrambler_enable(xhdmi);
+		else
+			xhdmirx_scrambler_disable(xhdmi);
+	}
+
+	if (xhdmi->stream.state != XSTATE_FRL_LINK_TRAININIG &&
+	    (event & HDMIRX_PIO_IN_MODE_MASK) && !xhdmi->stream.isfrl) {
+		if (data & HDMIRX_PIO_IN_MODE_MASK)
+			xhdmi->stream.ishdmi = true;
+		else /* DVI */
+			xhdmi->stream.ishdmi = false;
+
+		if (xhdmi->stream.state == XSTREAM_UP ||
+		    xhdmi->stream.state == XSTREAM_LOCK) {
+			/* up or lock state */
+			xhdmirx1_clear(xhdmi);
+			xhdmi->stream.state = XSTREAM_IDLE;
+			dev_dbg_ratelimited(xhdmi->dev, "state = XSTREAM_UP or LOCK\n");
+			/* 10 ms timer */
+			xhdmirx_tmr1_start(xhdmi, TIME_10MS);
+		}
+		/* modecall back does nothing */
+	}
+
+	if (event & HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK)
+		dev_dbg_ratelimited(xhdmi->dev, "scdc tmds clock ratio interrupt\n");
+
+	if (event & HDMIRX_PIO_IN_BRDG_OVERFLOW_MASK)
+		dev_dbg_ratelimited(xhdmi->dev, "bridge overflow interrupt\n");
+}
+
+/**
+ * xhdmirx_tmrint_handler - Function to handle the timer interrupt
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Function to handle the timer interrupt
+ */
+static void xhdmirx_tmrint_handler(struct xhdmirx_state *xhdmi)
+{
+	u32 status;
+
+	status = xhdmi_read(xhdmi, HDMIRX_TMR_STA_OFFSET);
+
+	dev_dbg_ratelimited(xhdmi->dev, "%s - timer int status reg = 0x%08x\n",
+			    __func__, status);
+
+	if (status & HDMIRX_TMR1_STA_CNT_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_TMR_STA_OFFSET,
+			    HDMIRX_TMR1_STA_CNT_EVT_MASK);
+
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG) {
+			switch (xhdmi->stream.frl.trainingstate) {
+			case XFRLSTATE_LTS_L:
+				xhdmi_execfrlstate(xhdmi);
+				break;
+			case XFRLSTATE_LTS_P:
+				fallthrough;
+			case XFRLSTATE_LTS_P_FRL_RDY:
+				fallthrough;
+			case XFRLSTATE_LTS_P_VID_RDY:
+				fallthrough;
+			case XFRLSTATE_LTS_3_RDY:
+				break;
+			default:
+				xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3_TMR;
+				xhdmi_execfrlstate(xhdmi);
+				break;
+			}
+			return;
+		}
+
+		if (xhdmi->stream.state == XSTREAM_IDLE) {
+			dev_dbg_ratelimited(xhdmi->dev, "state = XSTREAM_IDLE isfrl = %d trainingstate = %d",
+					    xhdmi->stream.isfrl, xhdmi->stream.frl.trainingstate);
+
+			if (!xhdmi->stream.isfrl ||
+			    (xhdmi->stream.isfrl &&
+			     xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P_VID_RDY)) {
+				xhdmirx_aux_enable(xhdmi);
+				/* enable audio */
+				/* release the internal vrst & lrst */
+				xhdmirx_rxcore_vrst_deassert(xhdmi);
+				xhdmirx_rxcore_lrst_deassert(xhdmi);
+				xhdmirx_link_enable(xhdmi);
+
+				xhdmi->stream.state = XSTREAM_INIT;
+				xhdmi->stream.getvidproptries = 0;
+			}
+			xhdmirx_tmr1_start(xhdmi, TIME_200MS);
+
+		} else if (xhdmi->stream.state == XSTREAM_INIT) {
+			dev_dbg_ratelimited(xhdmi->dev, "state = XSTREAM_INIT\n");
+			/* get video properties */
+			if (xhdmirx1_get_video_properties(xhdmi)) {
+				/* failed to get video properties */
+				xhdmirx_tmr1_start(xhdmi, TIME_200MS);
+			} else {
+				xhdmirx1_setpixelclk(xhdmi);
+
+				if (xhdmi->stream.isfrl) {
+					dev_dbg_ratelimited(xhdmi->dev, "Virtual Vid_Rdy: XSTREAM_INIT");
+
+					/* Toggle video reset for HDMI Rx core */
+					xhdmirx_rxcore_vrst_assert(xhdmi);
+					xhdmirx_rxcore_vrst_deassert(xhdmi);
+
+					/* Toggle bridge reset */
+					xhdmirx_ext_vrst_assert(xhdmi);
+					xhdmirx_sysrst_assert(xhdmi);
+
+					xhdmirx_ext_vrst_deassert(xhdmi);
+					xhdmirx_sysrst_deassert(xhdmi);
+
+					xhdmi->stream.state = XSTREAM_ARM;
+					xhdmirx_tmr1_start(xhdmi, TIME_200MS);
+				} else {
+					rxstreaminit(xhdmi);
+				}
+			}
+
+		} else if (xhdmi->stream.state == XSTREAM_ARM) {
+			dev_dbg(xhdmi->dev, "%s - state = XSTREAM_ARM\n", __func__);
+			xhdmirx_vtd_enable(xhdmi);
+			xhdmirx_vtdintr_enable(xhdmi);
+
+			/* 16 ms timer count is already loaded in VTD */
+			xhdmi->stream.state = XSTREAM_LOCK;
+		}
+	}
+
+	if (status & HDMIRX_TMR2_STA_CNT_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_TMR_STA_OFFSET,
+			    HDMIRX_TMR2_STA_CNT_EVT_MASK);
+	}
+
+	if (status & HDMIRX_TMR3_STA_CNT_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_TMR_STA_OFFSET,
+			    HDMIRX_TMR3_STA_CNT_EVT_MASK);
+		xhdmi_phyresetpoll(xhdmi);
+	}
+
+	if (status & HDMIRX_TMR4_STA_CNT_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_TMR_STA_OFFSET,
+			    HDMIRX_TMR4_STA_CNT_EVT_MASK);
+		/* currently unused */
+	}
+}
+
+/**
+ * xhdmirx_vtdint_handler - Function to handle the VTD interrupt
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Function to handle the video timing detector interrupt
+ */
+static void xhdmirx_vtdint_handler(struct xhdmirx_state *xhdmi)
+{
+	u32 status;
+	u32 totalpixfrlratio = 0, activepixfrlratio = 0;
+	u64 vidclk = 0;
+
+	status = xhdmi_read(xhdmi, HDMIRX_VTD_STA_OFFSET);
+
+	if (status & HDMIRX_VTD_STA_TIMEBASE_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_VTD_STA_OFFSET,
+			    HDMIRX_VTD_STA_TIMEBASE_EVT_MASK);
+		dev_dbg_ratelimited(xhdmi->dev, "vtd intr\n");
+
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG)
+			return;
+
+		if (xhdmi->stream.state == XSTREAM_LOCK) {
+			int ret;
+			u32 divisor, dividend;
+
+			dev_dbg_ratelimited(xhdmi->dev, "%s - state = XSTREAM_LOCK\n", __func__);
+			/* Get video timings */
+			ret = xhdmirx1_get_vid_timing(xhdmi);
+
+			if (!ret) {
+				if (xhdmi->stream.isfrl) {
+					u32 val;
+
+					val = xhdmi_getfrlactivepixratio(xhdmi);
+					activepixfrlratio = DIV_ROUND_CLOSEST(val, 1000);
+
+					val = xhdmi_getfrltotalpixratio(xhdmi);
+					totalpixfrlratio = DIV_ROUND_CLOSEST(val, 1000);
+
+					vidclk = activepixfrlratio *
+						 DIV_ROUND_CLOSEST(xhdmi->frlclkfreqkhz, 100);
+					vidclk = DIV_ROUND_CLOSEST(vidclk, totalpixfrlratio);
+					xhdmi->stream.refclk = vidclk * 100000;
+					if (xhdmirx1_get_video_properties(xhdmi))
+						dev_err_ratelimited(xhdmi->dev, "Failed get video properties!");
+				}
+
+				xhdmirx1_setpixelclk(xhdmi);
+
+				if (xhdmi->stream.isfrl) {
+					u32 remainder;
+
+					vidclk = (xhdmi->stream.pixelclk / 100000) / COREPIXPERCLK;
+					vidclk = xhdmi->vidclkfreqkhz / vidclk;
+					remainder = vidclk % 100;
+					vidclk = vidclk / 100;
+					if (remainder >= 50)
+						vidclk++;
+
+					xhdmirx_setfrl_vclkvckeratio(xhdmi, vidclk);
+				}
+
+				/* calculate framerate */
+				divisor = xhdmi->stream.video.timing.vtot[0];
+				divisor *= xhdmi->stream.video.timing.htot;
+				dividend = xhdmi->stream.pixelclk;
+				if (xhdmi->stream.video.colorspace == XCS_YUV420)
+					dividend <<= 1;
+				xhdmi->stream.video.framerate =
+					DIV_ROUND_CLOSEST(dividend, divisor);
+
+				/* enable AXI stream output */
+				xhdmirx_axi4s_enable(xhdmi);
+
+				xhdmi->stream.state = XSTREAM_UP;
+				xhdmi->stream.syncstatus = XSYNCSTAT_SYNC_EST;
+
+				rxstreamup(xhdmi);
+
+				xhdmi->hdmi_stream_up = 1;
+			}
+		} else if (xhdmi->stream.state == XSTREAM_UP) {
+			int ret;
+
+			dev_dbg_ratelimited(xhdmi->dev, "%s - state = XSTREAM_UP\n", __func__);
+			ret = xhdmirx1_get_vid_timing(xhdmi);
+			if (!ret) {
+				if (xhdmi->stream.syncstatus == XSYNCSTAT_SYNC_LOSS) {
+					xhdmi->stream.syncstatus = XSYNCSTAT_SYNC_EST;
+					/* call syncloss callback */
+				}
+			} else {
+				if (!xhdmi->stream.isfrl) {
+					/* in tmds mode just set state to lock */
+					xhdmi->stream.state = XSTREAM_LOCK;
+				} else {
+					/* need to do frl mode */
+					xhdmirx_rxcore_lrst_assert(xhdmi);
+					xhdmirx_rxcore_lrst_deassert(xhdmi);
+					xhdmirx_aux_disable(xhdmi);
+
+					streamdown(xhdmi);
+
+					/* switch to bursty vcke generation */
+					xhdmirx_setfrl_vclkvckeratio(xhdmi, 0);
+					xhdmi->stream.state = XSTREAM_INIT;
+					xhdmirx_aux_enable(xhdmi);
+					xhdmirx_tmr1_start(xhdmi, TIME_200MS);
+				}
+			}
+		}
+	} else if (status & HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_VTD_STA_OFFSET,
+			    HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK);
+
+		if (xhdmi->stream.state == XSTREAM_UP)
+			xhdmi->stream.syncstatus = XSYNCSTAT_SYNC_LOSS;
+		dev_dbg(xhdmi->dev, "%s - Sync Loss event\n", __func__);
+	}
+}
+
+/**
+ * xhdmirx_auxint_handler - Function to handle the AUX interrupt
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Function to handle the AUX packets interrupt
+ */
+static void xhdmirx_auxint_handler(struct xhdmirx_state *xhdmi)
+{
+	u32 status;
+
+	status = xhdmi_read(xhdmi, HDMIRX_AUX_STA_OFFSET);
+	dev_dbg_ratelimited(xhdmi->dev, "aux intr\n");
+
+	if (status & HDMIRX_AUX_STA_DYN_HDR_EVT_MASK) {
+		dev_dbg_ratelimited(xhdmi->dev, "aux dyn intr\n");
+		xhdmi_write(xhdmi, HDMIRX_AUX_STA_OFFSET,
+			    HDMIRX_AUX_STA_DYN_HDR_EVT_MASK);
+	}
+
+	if (status & HDMIRX_AUX_STA_VRR_CD_EVT_MASK) {
+		dev_dbg_ratelimited(xhdmi->dev, "aux VRR intr\n");
+		xhdmi_write(xhdmi, HDMIRX_AUX_STA_OFFSET,
+			    HDMIRX_AUX_STA_VRR_CD_EVT_MASK);
+	}
+
+	if (status & HDMIRX_AUX_STA_FSYNC_CD_EVT_MASK) {
+		dev_dbg_ratelimited(xhdmi->dev, "aux fsync intr\n");
+		xhdmi_write(xhdmi, HDMIRX_AUX_STA_OFFSET,
+			    HDMIRX_AUX_STA_FSYNC_CD_EVT_MASK);
+	}
+
+	if (status & HDMIRX_AUX_STA_GCP_CD_EVT_MASK) {
+		dev_dbg_ratelimited(xhdmi->dev, "aux gcp intr\n");
+		xhdmi_write(xhdmi, HDMIRX_AUX_STA_OFFSET,
+			    HDMIRX_AUX_STA_GCP_CD_EVT_MASK);
+
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG)
+			return;
+
+		if (status & HDMIRX_AUX_STA_GCP_MASK) {
+			xhdmi->stream.video.colordepth = xhdmirx1_getgcp_colordepth(xhdmi);
+
+			if (xhdmi->stream.isfrl) {
+				dev_dbg_ratelimited(xhdmi->dev, "FRL Mode Stream Down");
+				xhdmirx_aux_disable(xhdmi);
+				streamdown(xhdmi);
+				xhdmirx_aux_enable(xhdmi);
+				xhdmi->stream.state = XSTREAM_INIT;
+				xhdmirx_tmr1_start(xhdmi, TIME_200MS);
+			}
+		}
+	}
+
+	if (status & HDMIRX_AUX_STA_NEW_MASK) {
+		int i;
+
+		dev_dbg_ratelimited(xhdmi->dev, "aux new packet intr\n");
+		xhdmi_write(xhdmi, HDMIRX_AUX_STA_OFFSET,
+			    HDMIRX_AUX_STA_NEW_MASK);
+
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG)
+			return;
+
+		if (!xhdmi->stream.isfrl)
+			xhdmi->stream.ishdmi = true;
+
+		xhdmi->aux.header.data = xhdmi_read(xhdmi,
+						    HDMIRX_AUX_DAT_OFFSET);
+		for (i = 0; i < 8; i++)
+			xhdmi->aux.data.data[i] =
+				xhdmi_read(xhdmi, HDMIRX_AUX_DAT_OFFSET);
+		/* aux call back */
+	}
+
+	if (status & HDMIRX_AUX_STA_ERR_MASK) {
+		dev_dbg_ratelimited(xhdmi->dev, "aux err intr\n");
+		xhdmi_write(xhdmi, HDMIRX_AUX_STA_OFFSET,  HDMIRX_AUX_STA_ERR_MASK);
+		if (xhdmi->stream.state == XSTATE_FRL_LINK_TRAININIG)
+			return;
+		/* link error call back */
+	}
+}
+
+/**
+ * xhdmirx_frlint_handler - Function to handle the FRL interrupt
+ *
+ * @xhdmi: pointer to driver state
+ *
+ * Function to handle the FRL interrupts
+ */
+static void xhdmirx_frlint_handler(struct xhdmirx_state *xhdmi)
+{
+	u32 data;
+	u8 streamdownflag = false;
+
+	data = xhdmi_read(xhdmi, HDMIRX_FRL_STA_OFFSET);
+	dev_dbg_ratelimited(xhdmi->dev, "FRL intr");
+
+	if (data & HDMIRX_FRL_STA_RATE_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_FRL_STA_OFFSET, HDMIRX_FRL_STA_RATE_EVT_MASK);
+		/* TODO disable Dynamic HDR */
+		streamdown(xhdmi);
+		xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3_RATE_CH;
+		xhdmi_execfrlstate(xhdmi);
+	}
+
+	if (data & HDMIRX_FRL_STA_FLT_UPD_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_FRL_STA_OFFSET, HDMIRX_FRL_STA_FLT_UPD_EVT_MASK);
+		xhdmi->stream.frl.fltupdateasserted = false;
+		dev_dbg_ratelimited(xhdmi->dev, "RX: INTR FLT_UP cleared %d",
+				    xhdmirx_tmr1_getval(xhdmi));
+		switch (xhdmi->stream.frl.trainingstate) {
+		case XFRLSTATE_LTS_P:
+			fallthrough;
+		case XFRLSTATE_LTS_3_RDY:
+			fallthrough;
+		case XFRLSTATE_LTS_3_ARM_VID_RDY:
+			fallthrough;
+		case XFRLSTATE_LTS_3_ARM_LNK_RDY:
+			fallthrough;
+		case XFRLSTATE_LTS_P_FRL_RDY:
+			break;
+		default:
+			xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3;
+			break;
+		}
+		xhdmi_execfrlstate(xhdmi);
+	}
+
+	/* Link training pattern has matched for all the active lanes */
+	if (data & HDMIRX_FRL_STA_FLT_PM_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_FRL_STA_OFFSET, HDMIRX_FRL_STA_FLT_PM_EVT_MASK);
+		dev_dbg_ratelimited(xhdmi->dev, "RX: INTR LTP_DET");
+		if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3 ||
+		    xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_3_LTP_DET) {
+			xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_3_LTP_DET;
+			xhdmi_execfrlstate(xhdmi);
+		}
+	}
+
+	if (data & HDMIRX_FRL_STA_LANE_LOCK_EVT_MASK) {
+		u8 temp = xhdmi_frlddcreadfield(xhdmi, XSCDCFIELD_LNS_LOCK);
+
+		xhdmi_write(xhdmi, HDMIRX_FRL_STA_OFFSET, HDMIRX_FRL_STA_LANE_LOCK_EVT_MASK);
+
+		if (((xhdmi->stream.frl.lanes == 3 ? 0x7 : 0xF) == temp) &&
+		    xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P) {
+			dev_dbg_ratelimited(xhdmi->dev, "LTS_P_FRL_RDY");
+			xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_P_FRL_RDY;
+			dev_dbg_ratelimited(xhdmi->dev, "RX: INTR FRL_START");
+			xhdmi_execfrlstate(xhdmi);
+		}
+	}
+
+	if (data & HDMIRX_FRL_STA_SKEW_LOCK_EVT_MASK) {
+		xhdmi_write(xhdmi, HDMIRX_FRL_STA_OFFSET, HDMIRX_FRL_STA_SKEW_LOCK_EVT_MASK);
+
+		if (xhdmi_read(xhdmi, HDMIRX_FRL_STA_OFFSET) & HDMIRX_FRL_STA_SKEW_LOCK_MASK) {
+			if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P_VID_RDY) {
+				streamdownflag = true;
+				dev_dbg_ratelimited(xhdmi->dev, "skew lock err 1 occurred!");
+			} else {
+				/* Skew has locked. No actions needed */
+				dev_dbg_ratelimited(xhdmi->dev, "skew lock occurred!");
+			}
+
+			xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_P_VID_RDY;
+		} else {
+			if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P_FRL_RDY) {
+				streamdownflag = true;
+			} else if (xhdmi->stream.frl.trainingstate != XFRLSTATE_LTS_3_RATE_CH) {
+				/*
+				 * unexpected skew lock event is true only when it is not caused by
+				 * rate change request.
+				 */
+				dev_dbg_ratelimited(xhdmi->dev, "skew lock err 2 occurred!");
+			}
+
+			if (xhdmi->stream.frl.trainingstate == XFRLSTATE_LTS_P_VID_RDY)
+				xhdmi->stream.frl.trainingstate = XFRLSTATE_LTS_P_FRL_RDY;
+		}
+
+		if (streamdownflag) {
+			xhdmirx_rxcore_lrst_assert(xhdmi);
+			xhdmirx_rxcore_vrst_assert(xhdmi);
+			xhdmirx_ext_vrst_assert(xhdmi);
+			xhdmirx_sysrst_assert(xhdmi);
+
+			xhdmirx_vtd_disable(xhdmi);
+			/* TODO Dynamic HDR disable */
+			streamdown(xhdmi);
+		}
+
+		switch (xhdmi->stream.frl.trainingstate) {
+		case XFRLSTATE_LTS_P_FRL_RDY:
+			xhdmi->stream.state = XSTREAM_DOWN;
+			break;
+		case XFRLSTATE_LTS_P_VID_RDY:
+			/* set stream status to idle */
+			xhdmi->stream.state = XSTREAM_IDLE;
+			/* Load timer for 10 ms */
+			xhdmirx_tmr1_start(xhdmi, TIME_10MS);
+			break;
+		default:
+			break;
+		}
+	}
+}
+
+static irqreturn_t xhdmirx_irq_handler(int irq, void *param)
+{
+	struct xhdmirx_state *xhdmi = (struct xhdmirx_state *)param;
+
+	/* read status registers */
+	xhdmi->intrstatus[0] = xhdmi_read(xhdmi, HDMIRX_PIO_STA_OFFSET) &
+				HDMIRX_PIO_STA_IRQ_MASK;
+	xhdmi->intrstatus[1] = xhdmi_read(xhdmi, HDMIRX_TMR_STA_OFFSET) &
+				HDMIRX_TMR_STA_IRQ_MASK;
+	xhdmi->intrstatus[2] = xhdmi_read(xhdmi, HDMIRX_VTD_STA_OFFSET) &
+				HDMIRX_VTD_STA_IRQ_MASK;
+	xhdmi->intrstatus[3] = xhdmi_read(xhdmi, HDMIRX_DDC_STA_OFFSET) &
+				HDMIRX_DDC_STA_IRQ_MASK;
+	xhdmi->intrstatus[4] = xhdmi_read(xhdmi, HDMIRX_AUX_STA_OFFSET) &
+				HDMIRX_AUX_STA_IRQ_MASK;
+	xhdmi->intrstatus[5] = xhdmi_read(xhdmi, HDMIRX_AUD_STA_OFFSET) &
+				HDMIRX_AUD_STA_IRQ_MASK;
+	xhdmi->intrstatus[6] = xhdmi_read(xhdmi, HDMIRX_LNKSTA_STA_OFFSET) &
+				HDMIRX_LNKSTA_STA_IRQ_MASK;
+	xhdmi->intrstatus[7] = xhdmi_read(xhdmi, HDMIRX_FRL_STA_OFFSET) &
+				HDMIRX_FRL_STA_IRQ_MASK;
+
+	/* mask interrupt request */
+	xhdmirx_disable_allintr(xhdmi);
+
+	/* call bottom-half */
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t xhdmirx_irq_thread(int irq, void *param)
+{
+	struct xhdmirx_state *xhdmi = (struct xhdmirx_state *)param;
+
+	if (xhdmi->intrstatus[0])
+		xhdmirx_pioint_handler(xhdmi);
+	if (xhdmi->intrstatus[1])
+		xhdmirx_tmrint_handler(xhdmi);
+	if (xhdmi->intrstatus[2])
+		xhdmirx_vtdint_handler(xhdmi);
+	if (xhdmi->intrstatus[3])
+		xhdmi_write(xhdmi, HDMIRX_DDC_STA_OFFSET, xhdmi->intrstatus[3]);
+	if (xhdmi->intrstatus[4])
+		xhdmirx_auxint_handler(xhdmi);
+	if (xhdmi->intrstatus[5])
+		xhdmi_write(xhdmi, HDMIRX_AUD_STA_OFFSET, xhdmi->intrstatus[5]);
+	if (xhdmi->intrstatus[6])
+		xhdmi_write(xhdmi, HDMIRX_LNKSTA_STA_OFFSET, xhdmi->intrstatus[6]);
+	if (xhdmi->intrstatus[7])
+		xhdmirx_frlint_handler(xhdmi);
+
+	xhdmirx_enable_allintr(xhdmi);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xhdmirx_load_edid - Function to load the user EDID
+ *
+ * @xhdmi: pointer to driver state
+ * @edid: buffer pointer to user EDID
+ * @length: Length of buffer
+ *
+ * Returns: 0 on success else -EINVAL
+ */
+static int xhdmirx_load_edid(struct xhdmirx_state *xhdmi, u8 *edid, int length)
+{
+	u32 wordcount;
+	int i;
+
+	wordcount = xhdmi_read(xhdmi, HDMIRX_DDC_EDID_STA_OFFSET);
+	wordcount &= 0xFFFF;
+
+	if (wordcount < length) {
+		dev_err(xhdmi->dev, "fail as length > edid wc!\n");
+		return -EINVAL;
+	}
+
+	xhdmi_write(xhdmi, HDMIRX_DDC_EDID_WP_OFFSET, 0);
+
+	for (i = 0; i < length; i++)
+		xhdmi_write(xhdmi, HDMIRX_DDC_EDID_DATA_OFFSET, edid[i]);
+
+	xhdmi_write(xhdmi, HDMIRX_DDC_CTRL_SET_OFFSET,
+		    HDMIRX_DDC_CTRL_EDID_EN_MASK);
+
+	return 0;
+}
+
+static void xhdmirx_reset(struct xhdmirx_state *xhdmi)
+{
+	/* assert resets */
+	xhdmirx_rxcore_vrst_assert(xhdmi);
+	xhdmirx_rxcore_lrst_assert(xhdmi);
+	xhdmirx_sysrst_assert(xhdmi);
+
+	/* deassert resets */
+	xhdmirx_sysrst_deassert(xhdmi);
+	xhdmirx_rxcore_lrst_deassert(xhdmi);
+	xhdmirx_rxcore_vrst_deassert(xhdmi);
+}
+
+static void xhdmirx_init(struct xhdmirx_state *xhdmi)
+{
+	u32 mask;
+
+	xhdmirx1_clear(xhdmi);
+	xhdmi->stream.frl.fltnoretrain = false;
+	xhdmi->stream.frl.fltnotimeout = false;
+
+	xhdmirx_frlintr_disable(xhdmi);
+	xhdmi_frlreset(xhdmi, true);
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_SINK_VER, 1);
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FRL_RATE, 0);
+
+	xhdmirx_pio_disable(xhdmi);
+	xhdmirx_tmr1_disable(xhdmi);
+	xhdmirx_tmr2_disable(xhdmi);
+	xhdmirx_tmr3_disable(xhdmi);
+	xhdmirx_tmr4_disable(xhdmi);
+	xhdmirx_vtd_disable(xhdmi);
+	xhdmirx_ddc_disable(xhdmi);
+	xhdmirx_aux_disable(xhdmi);
+	xhdmirx_aud_disable(xhdmi);
+	xhdmirx_lnksta_disable(xhdmi);
+	xhdmirx_piointr_disable(xhdmi);
+	xhdmirx_tmr1intr_disable(xhdmi);
+	xhdmirx_tmr2intr_disable(xhdmi);
+	xhdmirx_tmr3intr_disable(xhdmi);
+	xhdmirx_tmr4intr_disable(xhdmi);
+	xhdmirx_vtdintr_disable(xhdmi);
+	xhdmirx_ddcintr_disable(xhdmi);
+
+	xhdmirx_ddcscdc_clear(xhdmi);
+	xhdmirx_set_hpd(xhdmi, 0);
+
+	/* Rising edge mask */
+	mask = 0;
+	mask |= HDMIRX_PIO_IN_BRDG_OVERFLOW_MASK;
+	mask |= HDMIRX_PIO_IN_DET_MASK;
+	mask |= HDMIRX_PIO_IN_LNK_RDY_MASK;
+	mask |= HDMIRX_PIO_IN_VID_RDY_MASK;
+	mask |= HDMIRX_PIO_IN_MODE_MASK;
+	mask |= HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK;
+	mask |= HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK;
+	xhdmi_write(xhdmi, HDMIRX_PIO_IN_EVT_RE_OFFSET, mask);
+
+	mask = 0;
+	mask |= HDMIRX_PIO_IN_DET_MASK;
+	mask |= HDMIRX_PIO_IN_VID_RDY_MASK;
+	mask |= HDMIRX_PIO_IN_MODE_MASK;
+	mask |= HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK;
+	mask |= HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK;
+	xhdmi_write(xhdmi, HDMIRX_PIO_IN_EVT_FE_OFFSET, mask);
+
+	xhdmirx_tmr1_enable(xhdmi);
+	xhdmirx_tmr2_enable(xhdmi);
+	xhdmirx_tmr3_enable(xhdmi);
+	xhdmirx_tmr4_enable(xhdmi);
+	xhdmirx_tmr1intr_enable(xhdmi);
+	xhdmirx_tmr2intr_enable(xhdmi);
+	xhdmirx_tmr3intr_enable(xhdmi);
+	xhdmirx_tmr4intr_enable(xhdmi);
+
+	xhdmirx_skewlockevt_enable(xhdmi);
+
+	/* set VTD for 200 ms different from bare metal's 16ms */
+	xhdmirx_vtd_settimebase(xhdmi, TIME_200MS);
+
+	xhdmirx_ddc_enable(xhdmi);
+	xhdmirx_ddcscdc_enable(xhdmi);
+	xhdmirx_auxintr_enable(xhdmi);
+	xhdmirx_lnksta_enable(xhdmi);
+
+	xhdmi_frlreset(xhdmi, false);
+	xhdmirx_frlintr_enable(xhdmi);
+	xhdmi->stream.frl.defaultltp.byte[0] = XLTP_LFSR0;
+	xhdmi->stream.frl.defaultltp.byte[1] = XLTP_LFSR1;
+	xhdmi->stream.frl.defaultltp.byte[2] = XLTP_LFSR2;
+	xhdmi->stream.frl.defaultltp.byte[3] = XLTP_LFSR3;
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FLT_READY, 1);
+	xhdmi_frlddcwritefield(xhdmi, XSCDCFIELD_FRL_RATE, 0);
+	xhdmi_setfrlratewrevent_en(xhdmi);
+
+	/* FRL EDID */
+	xhdmirx_load_edid(xhdmi, (u8 *)&xilinx_frl_edid,
+			  sizeof(xilinx_frl_edid));
+	xhdmirx_reset(xhdmi);
+}
+
+static void print_dt_clk_err_msg(struct xhdmirx_state *xhdmi, u8 isfrlclk, const char *range)
+{
+	dev_err(xhdmi->dev, "The %s port is driven by a clock outside the valid range (%s MHz)",
+		isfrlclk ? "frl_clk" : "vid_clk", range);
+}
+
+static int xhdmirx_parse_of(struct xhdmirx_state *xhdmi)
+{
+	struct device_node *node = xhdmi->dev->of_node;
+	struct device *dev = xhdmi->dev;
+	int ret;
+
+	ret = of_property_read_u16(node, "xlnx,edid-ram-size",
+				   &xhdmi->edid_ram_size);
+	if (ret) {
+		dev_err(dev, "xlnx,edid-ram-size property not found.\n");
+		return ret;
+	}
+
+	if (xhdmi->edid_ram_size != 256 && xhdmi->edid_ram_size != 512 &&
+	    xhdmi->edid_ram_size != 1024 && xhdmi->edid_ram_size != 4096) {
+		dev_err(dev, "invalid edid ram size %d in dt\n",
+			xhdmi->edid_ram_size);
+		return -EINVAL;
+	}
+
+	xhdmi->edid_blocks_max = xhdmi->edid_ram_size / XEDID_BLOCK_SIZE;
+
+	ret = of_property_read_u8(node, "xlnx,input-pixels-per-clock",
+				  &xhdmi->max_ppc);
+	if (ret) {
+		dev_err(dev, "xlnx,input-pixels-per-clock property not found.\n");
+		return ret;
+	}
+
+	if (xhdmi->max_ppc != 4 && xhdmi->max_ppc != 8) {
+		dev_err(dev, "dt pixels per clock %d  is invalid.\n",
+			xhdmi->max_ppc);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u8(node, "xlnx,max-bits-per-component",
+				  &xhdmi->max_bpc);
+	if (ret) {
+		dev_err(dev, "xlnx,max-bit-per-component property not found.\n");
+		return ret;
+	}
+
+	if (xhdmi->max_bpc != 8 && xhdmi->max_bpc != 10 &&
+	    xhdmi->max_bpc != 12 && xhdmi->max_bpc != 16) {
+		dev_err(dev, "dt max bits per component %d is invalid.\n",
+			xhdmi->max_bpc);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u8(node, "xlnx,max-frl-rate",
+				  &xhdmi->max_frl_rate);
+	if (ret) {
+		dev_err(dev, "xlnx,max-frl-rate property not found.\n");
+		return ret;
+	}
+
+	if (xhdmi->max_frl_rate != 4 && xhdmi->max_frl_rate != 5 &&
+	    xhdmi->max_frl_rate != 6) {
+		dev_err(dev, "dt max frl rate %d is invalid.\n", xhdmi->max_frl_rate);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,frl-clk-freq-khz",
+				   &xhdmi->frlclkfreqkhz);
+	if (ret) {
+		dev_err(dev, "frl clk freq khz property not found!");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,vid-clk-freq-khz",
+				   &xhdmi->vidclkfreqkhz);
+	if (ret) {
+		dev_err(dev, "video clk freq khz property not found!");
+		return ret;
+	}
+
+	switch (xhdmi->max_frl_rate) {
+	case 6:
+		/* 12G @ 4 Lanes */
+		if (xhdmi->frlclkfreqkhz < 449000 || xhdmi->frlclkfreqkhz > 451000) {
+			print_dt_clk_err_msg(xhdmi, 1, "449-451");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 399000 || xhdmi->vidclkfreqkhz > 401000) {
+			print_dt_clk_err_msg(xhdmi, 0, "399-401");
+			ret = -EINVAL;
+		}
+		break;
+	case 5:
+		/* 10G @ 4 Lanes */
+		if (xhdmi->frlclkfreqkhz < 379000 || xhdmi->frlclkfreqkhz > 381000) {
+			print_dt_clk_err_msg(xhdmi, 1, "379-381");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 374000 || xhdmi->vidclkfreqkhz > 376000) {
+			print_dt_clk_err_msg(xhdmi, 0, "374-376");
+			ret = -EINVAL;
+		}
+		break;
+	case 4:
+		/* 8G @ 4 Lanes */
+		if (xhdmi->frlclkfreqkhz < 324000 || xhdmi->frlclkfreqkhz > 326000) {
+			print_dt_clk_err_msg(xhdmi, 1, "324-326");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 299000 || xhdmi->vidclkfreqkhz > 301000) {
+			print_dt_clk_err_msg(xhdmi, 0, "299-301");
+			ret = -EINVAL;
+		}
+		break;
+	case 3:
+		/* 6G @ 4 Lanes */
+		if (xhdmi->frlclkfreqkhz < 249000 || xhdmi->frlclkfreqkhz > 251000) {
+			print_dt_clk_err_msg(xhdmi, 1, "249-251");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 224000 || xhdmi->vidclkfreqkhz > 226000) {
+			print_dt_clk_err_msg(xhdmi, 0, "224-226");
+			ret = -EINVAL;
+		}
+		break;
+	case 2:
+		/* 6G @ 4 Lanes */
+		if (xhdmi->frlclkfreqkhz < 199000 || xhdmi->frlclkfreqkhz > 201000) {
+			print_dt_clk_err_msg(xhdmi, 1, "199-201");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 174000 || xhdmi->vidclkfreqkhz > 176000) {
+			print_dt_clk_err_msg(xhdmi, 0, "174-176");
+			ret = -EINVAL;
+		}
+		break;
+	case 1:
+		/* 3G @ 3 Lanes */
+		if (xhdmi->frlclkfreqkhz < 149000 || xhdmi->frlclkfreqkhz > 151000) {
+			print_dt_clk_err_msg(xhdmi, 1, "149-151");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 149000 || xhdmi->vidclkfreqkhz > 151000) {
+			print_dt_clk_err_msg(xhdmi, 0, "149-151");
+			ret = -EINVAL;
+		}
+		break;
+	default:
+		/* TMDS */
+		if (xhdmi->frlclkfreqkhz < 149000 || xhdmi->frlclkfreqkhz > 151000) {
+			print_dt_clk_err_msg(xhdmi, 1, "149-151");
+			ret = -EINVAL;
+		}
+		if (xhdmi->vidclkfreqkhz < 149000 || xhdmi->vidclkfreqkhz > 151000) {
+			print_dt_clk_err_msg(xhdmi, 0, "149-151");
+			ret = -EINVAL;
+		}
+	}
+
+	return ret;
+}
+
+static void xhdmirx_phy_release(struct xhdmirx_state *xhdmi)
+{
+	int i, ret;
+
+	for (i = 0; i < XHDMI_MAX_LANES; i++) {
+		ret = phy_exit(xhdmi->phy[i]);
+		if (ret)
+			dev_err(xhdmi->dev, "fail to exit phy(%d) %d\n", i, ret);
+
+		xhdmi->phy[i] = NULL;
+	}
+}
+
+/**
+ * xhdmirx_dv_timings_cap - function to get the dv timings capabilities
+ *
+ * @subdev: pointer to v4l2 subdev
+ * @cap: Pointer to capable DV timings
+ *
+ * Returns: 0 on success else -EINVAL
+ */
+static int xhdmirx_dv_timings_cap(struct v4l2_subdev *subdev,
+				  struct v4l2_dv_timings_cap *cap)
+{
+	if (cap->pad != 0)
+		return -EINVAL;
+
+	cap->type = V4L2_DV_BT_656_1120;
+	cap->bt.max_width = 4096;
+	cap->bt.max_height = 2160;
+	cap->bt.min_pixelclock = 25000000;
+	cap->bt.max_pixelclock = 297000000;
+	cap->bt.standards = V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT |
+		V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT;
+	cap->bt.capabilities = V4L2_DV_BT_CAP_PROGRESSIVE |
+		V4L2_DV_BT_CAP_INTERLACED | V4L2_DV_BT_CAP_REDUCED_BLANKING |
+		V4L2_DV_BT_CAP_CUSTOM;
+
+	return 0;
+}
+
+/**
+ * xhdmirx_get_edid - function to get the EDID set currently
+ *
+ * @subdev: pointer to v4l2 subdev structure
+ * @edid: pointer to v4l2 edid structure to be filled to return
+ *
+ * This function returns the current EDID set in the HDMI Rx
+ *
+ * Returns: 0 on success else -EINVAL
+ */
+static int xhdmirx_get_edid(struct v4l2_subdev *subdev, struct v4l2_edid *edid)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(subdev);
+	int do_copy = 1;
+
+	if (edid->pad > 0)
+		return -EINVAL;
+
+	if (edid->start_block != 0)
+		return -EINVAL;
+
+	/* caller is only interested in the size of the EDID? */
+	if (edid->start_block == 0 && edid->blocks == 0)
+		do_copy = 0;
+
+	mutex_lock(&xhdmi->xhdmi_mutex);
+	/* user EDID active? */
+	if (xhdmi->edid_user_blocks) {
+		if (do_copy)
+			memcpy(edid->edid, xhdmi->edid_user,
+			       128 * (u16)xhdmi->edid_user_blocks);
+		edid->blocks = xhdmi->edid_user_blocks;
+	} else {
+		if (do_copy)
+			memcpy(edid->edid, &xilinx_frl_edid[0], sizeof(xilinx_frl_edid));
+		edid->blocks = sizeof(xilinx_frl_edid) / 128;
+	}
+	mutex_unlock(&xhdmi->xhdmi_mutex);
+
+	return 0;
+}
+
+static void xhdmirx_delayed_work_enable_hotplug(struct work_struct *work)
+{
+	struct delayed_work *dwork = to_delayed_work(work);
+	struct xhdmirx_state *xhdmi = container_of(dwork,
+						       struct xhdmirx_state,
+						       delayed_work_enable_hotplug);
+
+	xhdmirx_set_hpd(xhdmi, 1);
+}
+
+/**
+ * xhdmirx_set_edid - function to set the user EDID
+ *
+ * @subdev: pointer to v4l2 subdev structure
+ * @edid: pointer to v4l2 edid structure to be set
+ *
+ * This function sets the user EDID in the HDMI Rx
+ *
+ * Returns: 0 on success else -EINVAL or -E2BIG
+ */
+static int xhdmirx_set_edid(struct v4l2_subdev *subdev, struct v4l2_edid *edid)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(subdev);
+	int ret = 0;
+
+	if (edid->pad > 0)
+		return -EINVAL;
+
+	if (edid->start_block != 0)
+		return -EINVAL;
+
+	if (edid->blocks > xhdmi->edid_blocks_max) {
+		/* notify caller of how many EDID blocks this driver supports */
+		edid->blocks = xhdmi->edid_blocks_max;
+		return -E2BIG;
+	}
+
+	mutex_lock(&xhdmi->xhdmi_mutex);
+
+	xhdmi->edid_user_blocks = edid->blocks;
+
+	/* Disable hotplug and I2C access to EDID RAM from DDC port */
+	cancel_delayed_work_sync(&xhdmi->delayed_work_enable_hotplug);
+	xhdmirx_set_hpd(xhdmi, 0);
+
+	if (edid->blocks) {
+		memcpy(xhdmi->edid_user, edid->edid, 128 * edid->blocks);
+		ret = xhdmirx_load_edid(xhdmi, (u8 *)&xhdmi->edid_user,
+					128 * xhdmi->edid_user_blocks);
+		if (!ret)
+			/* enable hotplug after 100 ms */
+			queue_delayed_work(xhdmi->work_queue,
+					   &xhdmi->delayed_work_enable_hotplug,
+					   HZ / 10);
+	} else {
+		dev_dbg(xhdmi->dev, "edid->blocks = 0\n");
+	}
+
+	mutex_unlock(&xhdmi->xhdmi_mutex);
+
+	return ret;
+}
+
+static int xhdmirx_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(subdev);
+
+	dev_dbg(xhdmi->dev, "s_stream : enable %d\n", enable);
+	return 0;
+}
+
+/**
+ * xhdmirx_g_input_status - Gets the current link status
+ *
+ * @sd: pointer to v4l2 subdev struct
+ * @status: Pointer to status to be returned
+ *
+ * This function returns the link status. This is called and checked for
+ * before querying the dv timings.
+ *
+ * Returns: 0 on success else Link status
+ */
+static int xhdmirx_g_input_status(struct v4l2_subdev *sd, u32 *status)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(sd);
+
+	if (!xhdmi->hdmi_stream_up)
+		*status = V4L2_IN_ST_NO_SYNC | V4L2_IN_ST_NO_SIGNAL;
+	else
+		*status = 0;
+
+	dev_dbg_ratelimited(xhdmi->dev, "g_input_statue = 0x%08x\n", *status);
+
+	return 0;
+}
+
+/**
+ * xhdmirx_query_dv_timings - Gets the current incoming dv timings
+ *
+ * @subdev: pointer to v4l2 subdev
+ * @timings: pointer to the dv timings to be filled and returned
+ *
+ * This function returns the incoming stream's dv timings
+ *
+ * Returns: 0 on success else -ENOLINK
+ */
+static int xhdmirx_query_dv_timings(struct v4l2_subdev *subdev,
+				    struct v4l2_dv_timings *timings)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(subdev);
+
+	if (!xhdmi->hdmi_stream_up) {
+		dev_dbg(xhdmi->dev, "failed as no link\n");
+		return -ENOLINK;
+	}
+
+	v4l2_print_dv_timings(xhdmi->sd.name, "xhdmirx_query_dv_timing: ",
+			      &xhdmi->dv_timings, true);
+
+	*timings = xhdmi->dv_timings;
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+__xhdmirx_get_pad_format_ptr(struct xhdmirx_state *xhdmi,
+			     struct v4l2_subdev_state *sd_state,
+			     unsigned int pad, u32 which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		dev_dbg(xhdmi->dev, "%s V4L2_SUBDEV_FORMAT_TRY\n", __func__);
+		return v4l2_subdev_get_try_format(&xhdmi->sd, sd_state, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		dev_dbg(xhdmi->dev, "%s V4L2_SUBDEV_FORMAT_ACTIVE\n", __func__);
+		return &xhdmi->mbus_fmt;
+	default:
+		return NULL;
+	}
+}
+
+/**
+ * xhdmirx_set_format - Set the format to the pad
+ *
+ * @subdev: pointer to the v4l2 subdev struct
+ * @sd_state: pointer to subdev state
+ * @fmt: pointer to format structure
+ *
+ * This function will update the fmt structure passed to
+ * the current incoming stream format.
+ *
+ * Returns: 0 on success else -EINVAL
+ */
+static int xhdmirx_set_format(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(subdev);
+
+	if (fmt->pad > 0)
+		return -EINVAL;
+
+	fmt->format = xhdmi->mbus_fmt;
+	return 0;
+}
+
+/**
+ * xhdmirx_get_format - Function to get pad format
+ *
+ * @subdev: pointer to v4l2 subdev struct
+ * @sd_state: pointer to subdev state
+ * @fmt: pointer to the subdev format structure
+ *
+ * The fmt structure is updated based on incoming stream format.
+ *
+ * Returns: 0 on success else -EINVAL
+ */
+static int xhdmirx_get_format(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(subdev);
+	struct v4l2_mbus_framefmt *gfmt;
+
+	if (fmt->pad > 0)
+		return -EINVAL;
+
+	/* copy either try or currently-active (i.e. detected) format to caller */
+	gfmt = __xhdmirx_get_pad_format_ptr(xhdmi, sd_state, fmt->pad,
+					    fmt->which);
+	if (!gfmt)
+		return -EINVAL;
+
+	dev_dbg(xhdmi->dev, "width %d height %d code %d\n",
+		gfmt->width, gfmt->height, gfmt->code);
+
+	fmt->format = *gfmt;
+	return 0;
+}
+
+static int xhdmirx_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh,
+				   struct v4l2_event_subscription *sub)
+{
+	struct xhdmirx_state *xhdmi = to_xhdmirx_state(sd);
+	int rc = 0;
+
+	switch (sub->type) {
+	case V4L2_EVENT_SOURCE_CHANGE:
+		rc = v4l2_src_change_event_subdev_subscribe(sd, fh, sub);
+		dev_dbg(xhdmi->dev, "subscribed to V4L2_EVENT_SOURCE_CHANGE = %d\n", rc);
+		break;
+	default:
+		dev_dbg(xhdmi->dev, "subscribe_event() default: -EINVAL\n");
+		rc = -EINVAL;
+		break;
+	}
+
+	return rc;
+}
+
+static const struct v4l2_subdev_video_ops xvideo_ops = {
+	.s_stream		= xhdmirx_s_stream,
+	.query_dv_timings	= xhdmirx_query_dv_timings,
+	.g_input_status		= xhdmirx_g_input_status,
+};
+
+static const struct v4l2_subdev_core_ops xcore_ops = {
+	.subscribe_event	= xhdmirx_subscribe_event,
+	.unsubscribe_event	= v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_pad_ops xpad_ops = {
+	.get_edid		= xhdmirx_get_edid,
+	.set_edid		= xhdmirx_set_edid,
+	.dv_timings_cap		= xhdmirx_dv_timings_cap,
+	.get_fmt		= xhdmirx_get_format,
+	.set_fmt		= xhdmirx_set_format,
+};
+
+static const struct v4l2_subdev_ops xhdmirx_ops = {
+	.pad = &xpad_ops,
+	.video = &xvideo_ops,
+	.core = &xcore_ops,
+};
+
+static const struct media_entity_operations xmedia_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static int xhdmirx_probe_load_edid(struct xhdmirx_state *xhdmi)
+{
+	const struct firmware *fw_edid;
+	const char *fw_edid_name = "xilinx/xilinx-hdmi-rx-edid.bin";
+	u8 *edidbufptr = (u8 *)&xilinx_frl_edid;
+	int edidsize = sizeof(xilinx_frl_edid);
+
+	/* retrieve EDID */
+	if (!request_firmware(&fw_edid, fw_edid_name, xhdmi->dev)) {
+		int blocks = fw_edid->size / 128;
+
+		if (blocks == 0 || blocks > xhdmi->edid_blocks_max ||
+		    (fw_edid->size % 128)) {
+			dev_err(xhdmi->dev, "%s must be n * 128 bytes, with 1 <= n <= %d, using Xilinx built-in EDID instead.\n",
+				fw_edid_name, xhdmi->edid_blocks_max);
+		} else {
+			memcpy(xhdmi->edid_user, fw_edid->data, 128 * blocks);
+			xhdmi->edid_user_blocks = blocks;
+			edidbufptr = xhdmi->edid_user;
+			edidsize = xhdmi->edid_user_blocks * 128;
+		}
+		release_firmware(fw_edid);
+	}
+
+	if (edidbufptr == xhdmi->edid_user)
+		dev_info(xhdmi->dev, "Loading firmware edid\n");
+	else
+		dev_info(xhdmi->dev, "Loading Xilinx default edid\n");
+
+	return xhdmirx_load_edid(xhdmi, edidbufptr, edidsize);
+}
+
+static int xhdmirx_probe(struct platform_device *pdev)
+{
+	struct xhdmirx_state *xhdmi;
+	struct v4l2_subdev *sd;
+	struct resource *res;
+	union phy_configure_opts phy_cfg = {0};
+	int i, ret, irq, num_clks;
+
+	xhdmi = devm_kzalloc(&pdev->dev, sizeof(*xhdmi), GFP_KERNEL);
+	if (!xhdmi)
+		return -ENOMEM;
+
+	xhdmi->dev = &pdev->dev;
+
+	platform_set_drvdata(pdev, xhdmi);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xhdmi->regs = devm_ioremap_resource(xhdmi->dev, res);
+	if (IS_ERR(xhdmi->regs))
+		return PTR_ERR(xhdmi->regs);
+
+	xhdmi->edid_user = devm_kzalloc(xhdmi->dev,
+					XEDID_BLOCKS_MAX * XEDID_BLOCK_SIZE,
+					GFP_KERNEL);
+	if (!xhdmi->edid_user)
+		return -ENOMEM;
+
+	num_clks = ARRAY_SIZE(xhdmirx_clks);
+	xhdmi->clks = devm_kcalloc(xhdmi->dev, num_clks,
+				   sizeof(*xhdmi->clks), GFP_KERNEL);
+	if (!xhdmi->clks)
+		return -ENOMEM;
+
+	for (i = 0; i < num_clks; i++)
+		xhdmi->clks[i].id = xhdmirx_clks[i];
+
+	ret = devm_clk_bulk_get(xhdmi->dev, num_clks, xhdmi->clks);
+	if (ret)
+		return ret;
+
+	ret = clk_bulk_prepare_enable(num_clks, xhdmi->clks);
+	if (ret)
+		return ret;
+
+	mutex_init(&xhdmi->xhdmi_mutex);
+	xhdmi->work_queue = create_singlethread_workqueue("xilinx-hdmi-rx-wq");
+	if (!xhdmi->work_queue) {
+		dev_err(xhdmi->dev, "fail to create work queue!\n");
+		ret = -EINVAL;
+		goto mutex_err;
+	}
+	INIT_DELAYED_WORK(&xhdmi->delayed_work_enable_hotplug,
+			  xhdmirx_delayed_work_enable_hotplug);
+
+	xhdmirx_init(xhdmi);
+	xhdmirx_disable_allintr(xhdmi);
+
+	ret = xhdmirx_frlmodeenable(xhdmi, DEFAULT_LTPTHRESHOLD,
+				    xhdmi->stream.frl.defaultltp, true);
+	if (ret) {
+		dev_err(xhdmi->dev, "Failed to enable FRL mode %d", ret);
+		goto wrkq_err;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(xhdmi->dev, "get irq failed %d\n", irq);
+		ret = -EINVAL;
+		goto wrkq_err;
+	}
+
+	ret = devm_request_threaded_irq(xhdmi->dev, irq, xhdmirx_irq_handler,
+					xhdmirx_irq_thread, IRQF_ONESHOT,
+					dev_name(xhdmi->dev), xhdmi);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed to register irq handler %d\n", ret);
+		goto wrkq_err;
+	}
+
+	ret = xhdmirx_parse_of(xhdmi);
+	if (ret)
+		goto wrkq_err;
+
+	for (i = 0; i < XHDMI_MAX_LANES; i++) {
+		char phy_name[16];
+
+		snprintf(phy_name, sizeof(phy_name), "hdmi-phy%d", i);
+		xhdmi->phy[i] = devm_phy_get(xhdmi->dev, phy_name);
+		if (IS_ERR(xhdmi->phy[i])) {
+			ret = PTR_ERR(xhdmi->phy[i]);
+			xhdmi->phy[i] = NULL;
+			dev_err_probe(xhdmi->dev, ret, "failed to get phy lane %s index %d\n",
+				      phy_name, i);
+			goto phy_err;
+		}
+
+		ret = phy_init(xhdmi->phy[i]);
+		if (ret) {
+			dev_err(xhdmi->dev, "failed to init phy lane %d\n", i);
+			goto phy_err;
+		}
+	}
+
+	sd = &xhdmi->sd;
+	v4l2_subdev_init(sd, &xhdmirx_ops);
+	sd->dev = xhdmi->dev;
+	strscpy(sd->name, dev_name(xhdmi->dev), sizeof(sd->name));
+	sd->flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+	sd->entity.ops = &xmedia_ops;
+	v4l2_set_subdevdata(sd, xhdmi);
+	xhdmi->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&sd->entity, 1, &xhdmi->pad);
+	if (ret < 0) {
+		dev_err(xhdmi->dev, "failed to init media %d\n", ret);
+		goto phy_err;
+	}
+
+	ret = v4l2_async_register_subdev(sd);
+	if (ret < 0) {
+		dev_err(xhdmi->dev, "failed to register v4l subdev %d\n", ret);
+		goto media_err;
+	}
+
+	ret = xhdmirx_probe_load_edid(xhdmi);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed to load edid\n");
+		goto v4lsd_reg_err;
+	}
+
+	/* register phy callbacks */
+	phy_cfg.hdmi.phycb = 1;
+	phy_cfg.hdmi.hdmiphycb.cb = phy_rxinit_cb;
+	phy_cfg.hdmi.hdmiphycb.data = (void *)xhdmi;
+	phy_cfg.hdmi.hdmiphycb.type = RX_INIT_CB;
+	dev_dbg(xhdmi->dev, "config phy rxinit cb\n");
+	xhdmirx_phy_configure(xhdmi, &phy_cfg);
+
+	phy_cfg.hdmi.phycb = 1;
+	phy_cfg.hdmi.hdmiphycb.cb = phy_rxready_cb;
+	phy_cfg.hdmi.hdmiphycb.data = (void *)xhdmi;
+	phy_cfg.hdmi.hdmiphycb.type = RX_READY_CB;
+	dev_dbg(xhdmi->dev, "config phy rxready cb\n");
+	xhdmirx_phy_configure(xhdmi, &phy_cfg);
+
+	phy_cfg.hdmi.config_hdmi20 = 1;
+	dev_dbg(xhdmi->dev, "set phy to hdmi20\n");
+	xhdmirx_phy_configure(xhdmi, &phy_cfg);
+
+	xhdmirx_enable_allintr(xhdmi);
+
+	xhdmirx1_start(xhdmi);
+
+	dev_info(xhdmi->dev, "driver probe successful\n");
+
+	return 0;
+
+v4lsd_reg_err:
+	v4l2_async_unregister_subdev(sd);
+media_err:
+	media_entity_cleanup(&sd->entity);
+phy_err:
+	xhdmirx_phy_release(xhdmi);
+wrkq_err:
+	cancel_delayed_work(&xhdmi->delayed_work_enable_hotplug);
+	destroy_workqueue(xhdmi->work_queue);
+mutex_err:
+	mutex_destroy(&xhdmi->xhdmi_mutex);
+	clk_bulk_disable_unprepare(num_clks, xhdmi->clks);
+
+	return ret;
+}
+
+static int xhdmirx_remove(struct platform_device *pdev)
+{
+	struct xhdmirx_state *xhdmi = platform_get_drvdata(pdev);
+	struct v4l2_subdev *sd = &xhdmi->sd;
+	int num_clks = ARRAY_SIZE(xhdmirx_clks);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	xhdmirx_phy_release(xhdmi);
+	cancel_delayed_work(&xhdmi->delayed_work_enable_hotplug);
+	destroy_workqueue(xhdmi->work_queue);
+	mutex_destroy(&xhdmi->xhdmi_mutex);
+	clk_bulk_disable_unprepare(num_clks, xhdmi->clks);
+
+	dev_info(xhdmi->dev, "driver removed successfully\n");
+	return 0;
+}
+
+static const struct of_device_id xhdmirx_of_id_table[] = {
+	{ .compatible = "xlnx,v-hdmi-rxss1-1.1" },
+	{ .compatible = "xlnx,v-hdmi-rxss1-1.2" },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, xhdmirx_of_id_table);
+
+static struct platform_driver xhdmirx_driver = {
+	.driver = {
+		.name		= "xlnx-hdmi21rxss",
+		.of_match_table	= xhdmirx_of_id_table,
+	},
+	.probe			= xhdmirx_probe,
+	.remove			= xhdmirx_remove,
+};
+
+module_platform_driver(xhdmirx_driver);
+
+MODULE_AUTHOR("Vishal Sagar <vishal.sagar@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx HDMI 2.1 Rx Subsystem Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-hls-common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-hls-common.h
@@ -0,0 +1,36 @@
+/*
+ * Xilinx HLS common header
+ *
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Radhey Shyam Pandey <radheys@xilinx.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __XILINX_HLS_COMMON_H__
+#define __XILINX_HLS_COMMON_H__
+
+#include <linux/bitops.h>
+
+#define XHLS_DEF_WIDTH                          1920
+#define XHLS_DEF_HEIGHT                         1080
+
+#define XHLS_REG_CTRL_DONE                      BIT(1)
+#define XHLS_REG_CTRL_IDLE                      BIT(2)
+#define XHLS_REG_CTRL_READY                     BIT(3)
+#define XHLS_REG_CTRL_AUTO_RESTART              BIT(7)
+#define XHLS_REG_GIE                            0x04
+#define XHLS_REG_GIE_GIE                        BIT(0)
+#define XHLS_REG_IER                            0x08
+#define XHLS_REG_IER_DONE                       BIT(0)
+#define XHLS_REG_IER_READY                      BIT(1)
+#define XHLS_REG_ISR                            0x0c
+#define XHLS_REG_ISR_DONE                       BIT(0)
+#define XHLS_REG_ISR_READY                      BIT(1)
+#define XHLS_REG_ROWS                           0x10
+#define XHLS_REG_COLS                           0x18
+
+#endif /* __XILINX_HLS_COMMON_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-hls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-hls.c
@@ -0,0 +1,505 @@
+/*
+ * Xilinx HLS Core
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/xilinx-hls.h>
+#include <linux/xilinx-v4l2-controls.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-hls-common.h"
+#include "xilinx-vip.h"
+
+/**
+ * struct xhls_device - Xilinx HLS Core device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @compatible: first DT compatible string for the device
+ * @formats: active V4L2 media bus formats at the sink and source pads
+ * @default_formats: default V4L2 media bus formats
+ * @vip_formats: format information corresponding to the pads active formats
+ * @model: additional description of IP implementation if available
+ * @ctrl_handler: control handler
+ * @user_mem: user portion of the register space
+ * @user_mem_size: size of the user portion of the register space
+ */
+struct xhls_device {
+	struct xvip_device xvip;
+	struct media_pad pads[2];
+
+	const char *compatible;
+
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_formats[2];
+
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_ctrl *model;
+
+	void __iomem *user_mem;
+	size_t user_mem_size;
+};
+
+static inline struct xhls_device *to_hls(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xhls_device, xvip.subdev);
+}
+
+/* -----------------------------------------------------------------------------
+ * Controls
+ */
+
+static const struct v4l2_ctrl_config xhls_model_ctrl = {
+	.id	= V4L2_CID_XILINX_HLS_MODEL,
+	.name	= "HLS Model",
+	.type	= V4L2_CTRL_TYPE_STRING,
+	.step	= 1,
+	.flags	= V4L2_CTRL_FLAG_READ_ONLY,
+};
+
+static int xhls_create_controls(struct xhls_device *xhls)
+{
+	struct v4l2_ctrl_config model = xhls_model_ctrl;
+	struct v4l2_ctrl *ctrl;
+	int ret;
+
+	model.max = strlen(xhls->compatible);
+	model.min = model.max;
+
+	ret = v4l2_ctrl_handler_init(&xhls->ctrl_handler, 1);
+	if (ret) {
+		dev_err(xhls->xvip.dev,
+			"failed to initializing controls (%d)\n", ret);
+		return ret;
+	}
+
+	ctrl = v4l2_ctrl_new_custom(&xhls->ctrl_handler, &model, NULL);
+
+	if (xhls->ctrl_handler.error || !ctrl) {
+		dev_err(xhls->xvip.dev, "failed to add controls\n");
+		v4l2_ctrl_handler_free(&xhls->ctrl_handler);
+		return xhls->ctrl_handler.error;
+	}
+
+	v4l2_ctrl_s_ctrl_string(ctrl, xhls->compatible);
+
+	xhls->xvip.subdev.ctrl_handler = &xhls->ctrl_handler;
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Core Operations
+ */
+
+static int xhls_user_read(struct xhls_device *xhls,
+			  struct xilinx_axi_hls_registers *regs)
+{
+	unsigned int i;
+	u32 offset;
+	u32 value;
+
+	if (regs->num_regs >= xhls->user_mem_size / 4)
+		return -EINVAL;
+
+	for (i = 0; i < regs->num_regs; ++i) {
+		if (copy_from_user(&offset, &regs->regs[i].offset,
+				   sizeof(offset)))
+			return -EFAULT;
+
+		if (offset >= xhls->user_mem_size || offset & 3)
+			return -EINVAL;
+
+		value = ioread32(xhls->user_mem + offset);
+
+		if (copy_to_user(&regs->regs[i].value, &value, sizeof(value)))
+			return -EFAULT;
+	}
+
+	return 0;
+}
+
+static int xhls_user_write(struct xhls_device *xhls,
+			   struct xilinx_axi_hls_registers *regs)
+{
+	struct xilinx_axi_hls_register reg;
+	unsigned int i;
+
+	if (regs->num_regs >= xhls->user_mem_size / 4)
+		return -EINVAL;
+
+	for (i = 0; i < regs->num_regs; ++i) {
+		if (copy_from_user(&reg, &regs->regs[i], sizeof(reg)))
+			return -EFAULT;
+
+		if (reg.offset >= xhls->user_mem_size || reg.offset & 3)
+			return -EINVAL;
+
+		iowrite32(reg.value, xhls->user_mem + reg.offset);
+	}
+
+	return 0;
+}
+
+static long xhls_ioctl(struct v4l2_subdev *subdev, unsigned int cmd, void *arg)
+{
+	struct xhls_device *xhls = to_hls(subdev);
+
+	switch (cmd) {
+	case XILINX_AXI_HLS_READ:
+		return xhls_user_read(xhls, arg);
+	case XILINX_AXI_HLS_WRITE:
+		return xhls_user_write(xhls, arg);
+	}
+
+	return -ENOTTY;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xhls_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xhls_device *xhls = to_hls(subdev);
+	struct v4l2_mbus_framefmt *format = &xhls->formats[XVIP_PAD_SINK];
+
+	if (!enable) {
+		xvip_write(&xhls->xvip, XVIP_CTRL_CONTROL, 0);
+		return 0;
+	}
+
+	xvip_write(&xhls->xvip, XHLS_REG_COLS, format->width);
+	xvip_write(&xhls->xvip, XHLS_REG_ROWS, format->height);
+
+	xvip_write(&xhls->xvip, XVIP_CTRL_CONTROL,
+		   XHLS_REG_CTRL_AUTO_RESTART | XVIP_CTRL_CONTROL_SW_ENABLE);
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+__xhls_get_pad_format(struct xhls_device *xhls,
+		      struct v4l2_subdev_state *sd_state,
+		      unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xhls->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xhls->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xhls_get_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xhls_device *xhls = to_hls(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xhls_get_pad_format(xhls, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xhls_set_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xhls_device *xhls = to_hls(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xhls_get_pad_format(xhls, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		fmt->format = *format;
+		return 0;
+	}
+
+	xvip_set_format_size(format, fmt);
+
+	fmt->format = *format;
+
+	/* Propagate the format to the source pad. */
+	format = __xhls_get_pad_format(xhls, sd_state, XVIP_PAD_SOURCE,
+					 fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	xvip_set_format_size(format, fmt);
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Operations
+ */
+
+static int xhls_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xhls_device *xhls = to_hls(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xhls->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xhls->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int xhls_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_core_ops xhls_core_ops = {
+	.ioctl = xhls_ioctl,
+};
+
+static struct v4l2_subdev_video_ops xhls_video_ops = {
+	.s_stream = xhls_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xhls_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xhls_get_format,
+	.set_fmt = xhls_set_format,
+};
+
+static struct v4l2_subdev_ops xhls_ops = {
+	.core   = &xhls_core_ops,
+	.video  = &xhls_video_ops,
+	.pad    = &xhls_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xhls_internal_ops = {
+	.open = xhls_open,
+	.close = xhls_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xhls_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static void xhls_init_formats(struct xhls_device *xhls)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize default and active formats */
+	format = &xhls->default_formats[XVIP_PAD_SINK];
+	format->code = xhls->vip_formats[XVIP_PAD_SINK]->code;
+	format->field = V4L2_FIELD_NONE;
+	format->colorspace = V4L2_COLORSPACE_SRGB;
+
+	format->width = xvip_read(&xhls->xvip, XHLS_REG_COLS);
+	format->height = xvip_read(&xhls->xvip, XHLS_REG_ROWS);
+
+	xhls->formats[XVIP_PAD_SINK] = *format;
+
+	format = &xhls->default_formats[XVIP_PAD_SOURCE];
+	*format = xhls->default_formats[XVIP_PAD_SINK];
+	format->code = xhls->vip_formats[XVIP_PAD_SOURCE]->code;
+
+	xhls->formats[XVIP_PAD_SOURCE] = *format;
+}
+
+static int xhls_parse_of(struct xhls_device *xhls)
+{
+	struct device *dev = xhls->xvip.dev;
+	struct device_node *node = xhls->xvip.dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id;
+	int ret;
+
+	ret = of_property_read_string(node, "compatible", &xhls->compatible);
+	if (ret < 0)
+		return -EINVAL;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (ports == NULL)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			const struct xvip_video_format *vip_format;
+
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "invalid format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			ret = of_property_read_u32(port, "reg", &port_id);
+			if (ret < 0) {
+				dev_err(dev, "no reg in DT");
+				return ret;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "invalid reg in DT");
+				return -EINVAL;
+			}
+
+			xhls->vip_formats[port_id] = vip_format;
+		}
+	}
+
+	return 0;
+}
+
+static int xhls_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xhls_device *xhls;
+	struct resource *mem;
+	int ret;
+
+	xhls = devm_kzalloc(&pdev->dev, sizeof(*xhls), GFP_KERNEL);
+	if (!xhls)
+		return -ENOMEM;
+
+	xhls->xvip.dev = &pdev->dev;
+
+	ret = xhls_parse_of(xhls);
+	if (ret < 0)
+		return ret;
+
+	ret = xvip_init_resources(&xhls->xvip);
+	if (ret < 0)
+		return ret;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	xhls->user_mem = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(xhls->user_mem))
+		return PTR_ERR(xhls->user_mem);
+	xhls->user_mem_size = resource_size(mem);
+
+	/* Reset and initialize the core */
+	xvip_reset(&xhls->xvip);
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xhls->xvip.subdev;
+	v4l2_subdev_init(subdev, &xhls_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xhls_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xhls);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	xhls_init_formats(xhls);
+
+	xhls->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xhls->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xhls_media_ops;
+	ret = media_entity_pads_init(&subdev->entity, 2, xhls->pads);
+	if (ret < 0)
+		goto error;
+
+	ret = xhls_create_controls(xhls);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xhls);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	dev_info(xhls->xvip.dev, "device %s found\n", xhls->compatible);
+
+	return 0;
+
+error:
+	v4l2_ctrl_handler_free(&xhls->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xhls->xvip);
+	return ret;
+}
+
+static int xhls_remove(struct platform_device *pdev)
+{
+	struct xhls_device *xhls = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xhls->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&xhls->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+
+	xvip_cleanup_resources(&xhls->xvip);
+
+	return 0;
+}
+
+static const struct of_device_id xhls_of_id_table[] = {
+	{ .compatible = "xlnx,v-hls" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xhls_of_id_table);
+
+static struct platform_driver xhls_driver = {
+	.driver = {
+		.name = "xilinx-hls",
+		.of_match_table = xhls_of_id_table,
+	},
+	.probe = xhls_probe,
+	.remove = xhls_remove,
+};
+
+module_platform_driver(xhls_driver);
+
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_DESCRIPTION("Xilinx HLS Core Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-m2m.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-m2m.c
@@ -0,0 +1,2219 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx V4L2 mem2mem driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Satish Kumar Nagireddy <satish.nagireddy.nagireddy@xilinx.com>
+ */
+
+#include <drm/drm_fourcc.h>
+#include <linux/delay.h>
+#include <linux/dma/xilinx_frmbuf.h>
+#include <linux/lcm.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-common.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mem2mem.h>
+#include <media/videobuf2-dma-contig.h>
+
+#include "xilinx-vip.h"
+
+#define XVIP_M2M_NAME		"xilinx-mem2mem"
+#define XVIP_M2M_DEFAULT_FMT	V4L2_PIX_FMT_RGB24
+
+/* Minimum and maximum widths are expressed in bytes */
+#define XVIP_M2M_MIN_WIDTH	1U
+#define XVIP_M2M_MAX_WIDTH	65535U
+#define XVIP_M2M_MIN_HEIGHT	1U
+#define XVIP_M2M_MAX_HEIGHT	8191U
+
+#define XVIP_M2M_DEF_WIDTH	1920
+#define XVIP_M2M_DEF_HEIGHT	1080
+
+#define XVIP_M2M_PAD_SINK	1
+#define XVIP_M2M_PAD_SOURCE	0
+
+/**
+ * struct xvip_graph_entity - Entity in the video graph
+ * @list: list entry in a graph entities list
+ * @node: the entity's DT node
+ * @entity: media entity, from the corresponding V4L2 subdev
+ * @asd: subdev asynchronous registration information
+ * @subdev: V4L2 subdev
+ * @streaming: status of the V4L2 subdev if streaming or not
+ */
+struct xvip_graph_entity {
+	struct list_head list;
+	struct device_node *node;
+	struct media_entity *entity;
+
+	struct v4l2_async_subdev asd;
+	struct v4l2_subdev *subdev;
+	bool streaming;
+};
+
+/**
+ * struct xvip_pipeline - Xilinx Video IP pipeline structure
+ * @pipe: media pipeline
+ * @lock: protects the pipeline @stream_count
+ * @use_count: number of DMA engines using the pipeline
+ * @stream_count: number of DMA engines currently streaming
+ * @num_dmas: number of DMA engines in the pipeline
+ * @xdev: Composite device the pipe belongs to
+ */
+struct xvip_pipeline {
+	struct media_pipeline pipe;
+
+	/* protects the pipeline @stream_count */
+	struct mutex lock;
+	unsigned int use_count;
+	unsigned int stream_count;
+
+	unsigned int num_dmas;
+	struct xvip_m2m_dev *xdev;
+};
+
+struct xventity_list {
+	struct list_head list;
+	struct media_entity *entity;
+};
+
+/**
+ * struct xvip_m2m_dev - Xilinx Video mem2mem device structure
+ * @v4l2_dev: V4L2 device
+ * @dev: (OF) device
+ * @media_dev: media device
+ * @notifier: V4L2 asynchronous subdevs notifier
+ * @entities: entities in the graph as a list of xvip_graph_entity
+ * @num_subdevs: number of subdevs in the pipeline
+ * @lock: This is to protect mem2mem context structure data
+ * @queued_lock: This is to protect video buffer information
+ * @dma: Video DMA channels
+ * @m2m_dev: V4L2 mem2mem device structure
+ * @v4l2_caps: V4L2 capabilities of the whole device
+ */
+struct xvip_m2m_dev {
+	struct v4l2_device v4l2_dev;
+	struct device *dev;
+
+	struct media_device media_dev;
+	struct v4l2_async_notifier notifier;
+	struct list_head entities;
+	unsigned int num_subdevs;
+
+	/* Protects to m2m context data */
+	struct mutex lock;
+
+	/* Protects vb2_v4l2_buffer data */
+	spinlock_t queued_lock;
+	struct xvip_m2m_dma *dma;
+	struct v4l2_m2m_dev *m2m_dev;
+	u32 v4l2_caps;
+};
+
+static inline struct xvip_pipeline *to_xvip_pipeline(struct media_entity *e)
+{
+	return container_of(e->pipe, struct xvip_pipeline, pipe);
+}
+
+/**
+ * struct xvip_m2m_dma - Video DMA channel
+ * @video: V4L2 video device associated with the DMA channel
+ * @xdev: composite mem2mem device the DMA channels belongs to
+ * @chan_tx: DMA engine channel for MEM2DEV transfer
+ * @chan_rx: DMA engine channel for DEV2MEM transfer
+ * @outfmt: active V4L2 OUTPUT port pixel format
+ * @capfmt: active V4L2 CAPTURE port pixel format
+ * @r: crop rectangle parameters
+ * @outinfo: format information corresponding to the active @outfmt
+ * @capinfo: format information corresponding to the active @capfmt
+ * @align: transfer alignment required by the DMA channel (in bytes)
+ * @crop: boolean flag to indicate if crop is requested
+ * @pads: media pads for the video M2M device entity
+ * @pipe: pipeline belonging to the DMA channel
+ */
+struct xvip_m2m_dma {
+	struct video_device video;
+	struct xvip_m2m_dev *xdev;
+	struct dma_chan *chan_tx;
+	struct dma_chan *chan_rx;
+	struct v4l2_format outfmt;
+	struct v4l2_format capfmt;
+	struct v4l2_rect r;
+	const struct xvip_video_format *outinfo;
+	const struct xvip_video_format *capinfo;
+	u32 align;
+	bool crop;
+
+	struct media_pad pads[2];
+	struct xvip_pipeline pipe;
+};
+
+/**
+ * struct xvip_m2m_ctx - VIPP mem2mem context
+ * @fh: V4L2 file handler
+ * @xdev: composite mem2mem device the DMA channels belongs to
+ * @xt: dma interleaved template for dma configuration
+ * @sgl: data chunk structure for dma_interleaved_template
+ */
+struct xvip_m2m_ctx {
+	struct v4l2_fh fh;
+	struct xvip_m2m_dev *xdev;
+	struct dma_interleaved_template xt;
+	struct data_chunk sgl[1];
+};
+
+static inline struct xvip_m2m_ctx *file2ctx(struct file *file)
+{
+	return container_of(file->private_data, struct xvip_m2m_ctx, fh);
+}
+
+static struct v4l2_subdev *
+xvip_dma_remote_subdev(struct media_pad *local, u32 *pad)
+{
+	struct media_pad *remote;
+
+	remote = media_entity_remote_pad(local);
+	if (!remote || !is_media_entity_v4l2_subdev(remote->entity))
+		return NULL;
+
+	if (pad)
+		*pad = remote->index;
+
+	return media_entity_to_v4l2_subdev(remote->entity);
+}
+
+static int xvip_dma_verify_format(struct xvip_m2m_dma *dma)
+{
+	struct v4l2_subdev_format fmt;
+	struct v4l2_subdev *subdev;
+	int ret;
+	int width, height;
+
+	subdev = xvip_dma_remote_subdev(&dma->pads[XVIP_PAD_SOURCE], &fmt.pad);
+	if (!subdev)
+		return -EPIPE;
+
+	fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(subdev, pad, get_fmt, NULL, &fmt);
+	if (ret < 0)
+		return ret == -ENOIOCTLCMD ? -EINVAL : ret;
+
+	if (dma->outinfo->code != fmt.format.code)
+		return -EINVAL;
+
+	if (V4L2_TYPE_IS_MULTIPLANAR(dma->outfmt.type)) {
+		width = dma->outfmt.fmt.pix_mp.width;
+		height = dma->outfmt.fmt.pix_mp.height;
+	} else {
+		width = dma->outfmt.fmt.pix.width;
+		height = dma->outfmt.fmt.pix.height;
+	}
+
+	if (width != fmt.format.width || height != fmt.format.height)
+		return -EINVAL;
+
+	return 0;
+}
+
+#define to_xvip_dma(vdev)	container_of(vdev, struct xvip_m2m_dma, video)
+/* -----------------------------------------------------------------------------
+ * Pipeline Stream Management
+ */
+
+/**
+ * xvip_subdev_set_streaming - Find and update streaming status of subdev
+ * @xdev: Composite video device
+ * @subdev: V4L2 sub-device
+ * @enable: enable/disable streaming status
+ *
+ * Walk the xvip graph entities list and find if subdev is present. Returns
+ * streaming status of subdev and update the status as requested
+ *
+ * Return: streaming status (true or false) if successful or warn_on if subdev
+ * is not present and return false
+ */
+static bool xvip_subdev_set_streaming(struct xvip_m2m_dev *xdev,
+				      struct v4l2_subdev *subdev, bool enable)
+{
+	struct xvip_graph_entity *entity;
+
+	list_for_each_entry(entity, &xdev->entities, list)
+		if (entity->node == subdev->dev->of_node) {
+			bool status = entity->streaming;
+
+			entity->streaming = enable;
+			return status;
+		}
+
+	WARN(1, "Should never get here\n");
+	return false;
+}
+
+static int xvip_entity_start_stop(struct xvip_m2m_dev *xdev,
+				  struct media_entity *entity, bool start)
+{
+	struct v4l2_subdev *subdev;
+	bool is_streaming;
+	int ret = 0;
+
+	dev_dbg(xdev->dev, "%s entity %s\n",
+		start ? "Starting" : "Stopping", entity->name);
+	subdev = media_entity_to_v4l2_subdev(entity);
+
+	/* This is to maintain list of stream on/off devices */
+	is_streaming = xvip_subdev_set_streaming(xdev, subdev, start);
+
+	/*
+	 * start or stop the subdev only once in case if they are
+	 * shared between sub-graphs
+	 */
+	if (start && !is_streaming) {
+		/* power-on subdevice */
+		ret = v4l2_subdev_call(subdev, core, s_power, 1);
+		if (ret < 0 && ret != -ENOIOCTLCMD) {
+			dev_err(xdev->dev,
+				"s_power on failed on subdev\n");
+			xvip_subdev_set_streaming(xdev, subdev, 0);
+			return ret;
+		}
+
+		/* stream-on subdevice */
+		ret = v4l2_subdev_call(subdev, video, s_stream, 1);
+		if (ret < 0 && ret != -ENOIOCTLCMD) {
+			dev_err(xdev->dev,
+				"s_stream on failed on subdev\n");
+			v4l2_subdev_call(subdev, core, s_power, 0);
+			xvip_subdev_set_streaming(xdev, subdev, 0);
+		}
+	} else if (!start && is_streaming) {
+		/* stream-off subdevice */
+		ret = v4l2_subdev_call(subdev, video, s_stream, 0);
+		if (ret < 0 && ret != -ENOIOCTLCMD) {
+			dev_err(xdev->dev,
+				"s_stream off failed on subdev\n");
+			xvip_subdev_set_streaming(xdev, subdev, 1);
+		}
+
+		/* power-off subdevice */
+		ret = v4l2_subdev_call(subdev, core, s_power, 0);
+		if (ret < 0 && ret != -ENOIOCTLCMD)
+			dev_err(xdev->dev,
+				"s_power off failed on subdev\n");
+	}
+
+	return ret;
+}
+
+/**
+ * xvip_pipeline_start_stop - Start ot stop streaming on a pipeline
+ * @xdev: Composite video device
+ * @dma: xvip dma
+ * @start: Start (when true) or stop (when false) the pipeline
+ *
+ * Walk the entities chain starting @dma and start or stop all of them
+ *
+ * Return: 0 if successful, or the return value of the failed video::s_stream
+ * operation otherwise.
+ */
+static int xvip_pipeline_start_stop(struct xvip_m2m_dev *xdev,
+				    struct xvip_m2m_dma *dma, bool start)
+{
+	struct media_graph graph;
+	struct media_entity *entity = &dma->video.entity;
+	struct media_device *mdev = entity->graph_obj.mdev;
+	struct xventity_list *temp, *_temp;
+	LIST_HEAD(ent_list);
+	int ret = 0;
+
+	mutex_lock(&mdev->graph_mutex);
+
+	/* Walk the graph to locate the subdev nodes */
+	ret = media_graph_walk_init(&graph, mdev);
+	if (ret)
+		goto error;
+
+	media_graph_walk_start(&graph, entity);
+
+	/* get the list of entities */
+	while ((entity = media_graph_walk_next(&graph))) {
+		struct xventity_list *ele;
+
+		/* We want to stream on/off only subdevs */
+		if (!is_media_entity_v4l2_subdev(entity))
+			continue;
+
+		/* Maintain the pipeline sequence in a list */
+		ele = kzalloc(sizeof(*ele), GFP_KERNEL);
+		if (!ele) {
+			ret = -ENOMEM;
+			goto error;
+		}
+
+		ele->entity = entity;
+		list_add(&ele->list, &ent_list);
+	}
+
+	if (start) {
+		list_for_each_entry_safe(temp, _temp, &ent_list, list) {
+			/* Enable all subdevs from sink to source */
+			ret = xvip_entity_start_stop(xdev, temp->entity, start);
+			if (ret < 0) {
+				dev_err(xdev->dev, "ret = %d for entity %s\n",
+					ret, temp->entity->name);
+				break;
+			}
+		}
+	} else {
+		list_for_each_entry_safe_reverse(temp, _temp, &ent_list, list)
+			/* Enable all subdevs from source to sink */
+			xvip_entity_start_stop(xdev, temp->entity, start);
+	}
+
+	list_for_each_entry_safe(temp, _temp, &ent_list, list) {
+		list_del(&temp->list);
+		kfree(temp);
+	}
+
+error:
+	mutex_unlock(&mdev->graph_mutex);
+	media_graph_walk_cleanup(&graph);
+	return ret;
+}
+
+/**
+ * xvip_pipeline_set_stream - Enable/disable streaming on a pipeline
+ * @pipe: The pipeline
+ * @on: Turn the stream on when true or off when false
+ *
+ * The pipeline is shared between all DMA engines connect at its input and
+ * output. While the stream state of DMA engines can be controlled
+ * independently, pipelines have a shared stream state that enable or disable
+ * all entities in the pipeline. For this reason the pipeline uses a streaming
+ * counter that tracks the number of DMA engines that have requested the stream
+ * to be enabled. This will walk the graph starting from each DMA and enable or
+ * disable the entities in the path.
+ *
+ * When called with the @on argument set to true, this function will increment
+ * the pipeline streaming count. If the streaming count reaches the number of
+ * DMA engines in the pipeline it will enable all entities that belong to the
+ * pipeline.
+ *
+ * Similarly, when called with the @on argument set to false, this function will
+ * decrement the pipeline streaming count and disable all entities in the
+ * pipeline when the streaming count reaches zero.
+ *
+ * Return: 0 if successful, or the return value of the failed video::s_stream
+ * operation otherwise. Stopping the pipeline never fails. The pipeline state is
+ * not updated when the operation fails.
+ */
+static int xvip_pipeline_set_stream(struct xvip_pipeline *pipe, bool on)
+{
+	struct xvip_m2m_dev *xdev;
+	struct xvip_m2m_dma *dma;
+	int ret = 0;
+
+	mutex_lock(&pipe->lock);
+	xdev = pipe->xdev;
+	dma = xdev->dma;
+
+	if (on) {
+		ret = xvip_pipeline_start_stop(xdev, dma, true);
+		if (ret < 0)
+			goto done;
+		pipe->stream_count++;
+	} else {
+		if (--pipe->stream_count == 0)
+			xvip_pipeline_start_stop(xdev, dma, false);
+	}
+
+done:
+	mutex_unlock(&pipe->lock);
+	return ret;
+}
+
+static int xvip_pipeline_validate(struct xvip_pipeline *pipe,
+				  struct xvip_m2m_dma *start)
+{
+	struct media_graph graph;
+	struct media_entity *entity = &start->video.entity;
+	struct media_device *mdev = entity->graph_obj.mdev;
+	unsigned int num_inputs = 0;
+	unsigned int num_outputs = 0;
+	int ret;
+
+	mutex_lock(&mdev->graph_mutex);
+
+	/* Walk the graph to locate the video nodes. */
+	ret = media_graph_walk_init(&graph, mdev);
+	if (ret) {
+		mutex_unlock(&mdev->graph_mutex);
+		return ret;
+	}
+
+	media_graph_walk_start(&graph, entity);
+
+	while ((entity = media_graph_walk_next(&graph))) {
+		if (entity->function != MEDIA_ENT_F_IO_V4L)
+			continue;
+
+		num_outputs++;
+		num_inputs++;
+	}
+
+	mutex_unlock(&mdev->graph_mutex);
+
+	media_graph_walk_cleanup(&graph);
+
+	/* We need at least one DMA to proceed */
+	if (num_outputs == 0 && num_inputs == 0)
+		return -EPIPE;
+
+	pipe->num_dmas = num_inputs + num_outputs;
+	pipe->xdev = start->xdev;
+
+	return 0;
+}
+
+static void __xvip_pipeline_cleanup(struct xvip_pipeline *pipe)
+{
+	pipe->num_dmas = 0;
+}
+
+/**
+ * xvip_pipeline_cleanup - Cleanup the pipeline after streaming
+ * @pipe: the pipeline
+ *
+ * Decrease the pipeline use count and clean it up if we were the last user.
+ */
+static void xvip_pipeline_cleanup(struct xvip_pipeline *pipe)
+{
+	mutex_lock(&pipe->lock);
+
+	/* If we're the last user clean up the pipeline. */
+	if (--pipe->use_count == 0)
+		__xvip_pipeline_cleanup(pipe);
+
+	mutex_unlock(&pipe->lock);
+}
+
+/**
+ * xvip_pipeline_prepare - Prepare the pipeline for streaming
+ * @pipe: the pipeline
+ * @dma: DMA engine at one end of the pipeline
+ *
+ * Validate the pipeline if no user exists yet, otherwise just increase the use
+ * count.
+ *
+ * Return: 0 if successful or -EPIPE if the pipeline is not valid.
+ */
+static int xvip_pipeline_prepare(struct xvip_pipeline *pipe,
+				 struct xvip_m2m_dma *dma)
+{
+	int ret;
+
+	mutex_lock(&pipe->lock);
+
+	/* If we're the first user validate and initialize the pipeline. */
+	if (pipe->use_count == 0) {
+		ret = xvip_pipeline_validate(pipe, dma);
+		if (ret < 0) {
+			__xvip_pipeline_cleanup(pipe);
+			goto done;
+		}
+	}
+
+	pipe->use_count++;
+	ret = 0;
+
+done:
+	mutex_unlock(&pipe->lock);
+	return ret;
+}
+
+static void xvip_m2m_dma_callback_mem2dev(void *data)
+{
+}
+
+static void xvip_m2m_dma_callback(void *data)
+{
+	struct xvip_m2m_ctx *ctx = data;
+	struct xvip_m2m_dev *xdev = ctx->xdev;
+	struct vb2_v4l2_buffer *src_vb, *dst_vb;
+
+	spin_lock(&xdev->queued_lock);
+	src_vb = v4l2_m2m_src_buf_remove(ctx->fh.m2m_ctx);
+	dst_vb = v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
+
+	dst_vb->vb2_buf.timestamp = src_vb->vb2_buf.timestamp;
+	dst_vb->flags &= ~V4L2_BUF_FLAG_TSTAMP_SRC_MASK;
+	dst_vb->flags |=
+		src_vb->flags & V4L2_BUF_FLAG_TSTAMP_SRC_MASK;
+	dst_vb->timecode = src_vb->timecode;
+
+	v4l2_m2m_buf_done(src_vb, VB2_BUF_STATE_DONE);
+	v4l2_m2m_buf_done(dst_vb, VB2_BUF_STATE_DONE);
+	v4l2_m2m_job_finish(xdev->m2m_dev, ctx->fh.m2m_ctx);
+	spin_unlock(&xdev->queued_lock);
+}
+
+/*
+ * Queue operations
+ */
+
+static int xvip_m2m_queue_setup(struct vb2_queue *vq,
+				u32 *nbuffers, u32 *nplanes,
+				u32 sizes[], struct device *alloc_devs[])
+{
+	struct xvip_m2m_ctx *ctx = vb2_get_drv_priv(vq);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct v4l2_format *f;
+	const struct xvip_video_format *info;
+	u32 i;
+
+	if (vq->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE) {
+		f = &dma->outfmt;
+		info = dma->outinfo;
+	} else {
+		f = &dma->capfmt;
+		info = dma->capinfo;
+	}
+
+	if (*nplanes) {
+		if (*nplanes != f->fmt.pix_mp.num_planes)
+			return -EINVAL;
+
+		for (i = 0; i < *nplanes; i++) {
+			if (sizes[i] < f->fmt.pix_mp.plane_fmt[i].sizeimage)
+				return -EINVAL;
+		}
+	} else {
+		*nplanes = info->buffers;
+		for (i = 0; i < info->buffers; i++)
+			sizes[i] = f->fmt.pix_mp.plane_fmt[i].sizeimage;
+	}
+
+	return 0;
+}
+
+static int xvip_m2m_buf_prepare(struct vb2_buffer *vb)
+{
+	struct xvip_m2m_ctx *ctx = vb2_get_drv_priv(vb->vb2_queue);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct v4l2_format *f;
+	const struct xvip_video_format *info;
+	u32 i;
+
+	if (vb->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE) {
+		f = &dma->outfmt;
+		info = dma->outinfo;
+	} else {
+		f = &dma->capfmt;
+		info = dma->capinfo;
+	}
+
+	for (i = 0; i < info->buffers; i++) {
+		if (vb2_plane_size(vb, i) <
+			f->fmt.pix_mp.plane_fmt[i].sizeimage) {
+			dev_err(ctx->xdev->dev,
+				"insufficient plane size (%u < %u)\n",
+				(u32)vb2_plane_size(vb, i),
+				f->fmt.pix_mp.plane_fmt[i].sizeimage);
+			return -EINVAL;
+		}
+
+		vb2_set_plane_payload(vb, i,
+				      f->fmt.pix_mp.plane_fmt[i].sizeimage);
+	}
+
+	return 0;
+}
+
+static void xvip_m2m_buf_queue(struct vb2_buffer *vb)
+{
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+	struct xvip_m2m_ctx *ctx = vb2_get_drv_priv(vb->vb2_queue);
+
+	v4l2_m2m_buf_queue(ctx->fh.m2m_ctx, vbuf);
+}
+
+static void xvip_m2m_stop_streaming(struct vb2_queue *q)
+{
+	struct xvip_m2m_ctx *ctx = vb2_get_drv_priv(q);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct xvip_pipeline *pipe = to_xvip_pipeline(&dma->video.entity);
+	struct vb2_v4l2_buffer *vbuf;
+
+	dma->crop = false;
+	if (q->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		dmaengine_terminate_sync(dma->chan_tx);
+	else
+		dmaengine_terminate_sync(dma->chan_rx);
+
+	if (ctx->xdev->num_subdevs) {
+		/* Stop the pipeline. */
+		xvip_pipeline_set_stream(pipe, false);
+
+		/* Cleanup the pipeline and mark it as being stopped. */
+		xvip_pipeline_cleanup(pipe);
+		media_pipeline_stop(&dma->video.entity);
+	}
+
+	for (;;) {
+		if (q->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+			vbuf = v4l2_m2m_src_buf_remove(ctx->fh.m2m_ctx);
+		else
+			vbuf = v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
+
+		if (!vbuf)
+			return;
+
+		spin_lock(&ctx->xdev->queued_lock);
+		v4l2_m2m_buf_done(vbuf, VB2_BUF_STATE_ERROR);
+		spin_unlock(&ctx->xdev->queued_lock);
+	}
+}
+
+static int xvip_m2m_start_streaming(struct vb2_queue *q, unsigned int count)
+{
+	struct xvip_m2m_ctx *ctx = vb2_get_drv_priv(q);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct xvip_m2m_dev *xdev = ctx->xdev;
+	struct xvip_pipeline *pipe;
+	int ret;
+
+	if (!xdev->num_subdevs)
+		return 0;
+
+	pipe = dma->video.entity.pipe
+	     ? to_xvip_pipeline(&dma->video.entity) : &dma->pipe;
+
+	ret = media_pipeline_start(&dma->video.entity, &pipe->pipe);
+	if (ret < 0)
+		goto error;
+
+	/* Verify that the configured format matches the output of the
+	 * connected subdev.
+	 */
+	ret = xvip_dma_verify_format(dma);
+	if (ret < 0)
+		goto error_stop;
+
+	ret = xvip_pipeline_prepare(pipe, dma);
+	if (ret < 0)
+		goto error_stop;
+
+	/* Start the pipeline. */
+	ret = xvip_pipeline_set_stream(pipe, true);
+	if (ret < 0)
+		goto error_stop;
+
+	return 0;
+error_stop:
+	media_pipeline_stop(&dma->video.entity);
+
+error:
+	xvip_m2m_stop_streaming(q);
+
+	return ret;
+}
+
+static const struct vb2_ops m2m_vb2_ops = {
+	.queue_setup = xvip_m2m_queue_setup,
+	.buf_prepare = xvip_m2m_buf_prepare,
+	.buf_queue = xvip_m2m_buf_queue,
+	.start_streaming = xvip_m2m_start_streaming,
+	.stop_streaming = xvip_m2m_stop_streaming,
+	.wait_prepare = vb2_ops_wait_prepare,
+	.wait_finish = vb2_ops_wait_finish,
+};
+
+static int xvip_m2m_queue_init(void *priv, struct vb2_queue *src_vq,
+			       struct vb2_queue *dst_vq)
+{
+	struct xvip_m2m_ctx *ctx = priv;
+	int ret;
+
+	src_vq->type = V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE;
+	src_vq->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF;
+	src_vq->drv_priv = ctx;
+	src_vq->buf_struct_size = sizeof(struct v4l2_m2m_buffer);
+	src_vq->ops = &m2m_vb2_ops;
+	src_vq->mem_ops = &vb2_dma_contig_memops;
+	src_vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_COPY;
+	src_vq->dev = ctx->xdev->v4l2_dev.dev;
+
+	ret = vb2_queue_init(src_vq);
+	if (ret)
+		return ret;
+
+	dst_vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
+	dst_vq->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF;
+	dst_vq->drv_priv = ctx;
+	dst_vq->buf_struct_size = sizeof(struct v4l2_m2m_buffer);
+	dst_vq->ops = &m2m_vb2_ops;
+	dst_vq->mem_ops = &vb2_dma_contig_memops;
+	dst_vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_COPY;
+	dst_vq->dev = ctx->xdev->v4l2_dev.dev;
+
+	return vb2_queue_init(dst_vq);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 ioctls
+ */
+
+static int
+xvip_dma_querycap(struct file *file, void *fh, struct v4l2_capability *cap)
+{
+	cap->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE;
+	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
+
+	strlcpy(cap->driver, XVIP_M2M_NAME, sizeof(cap->driver));
+	strlcpy(cap->card, XVIP_M2M_NAME, sizeof(cap->card));
+	strlcpy(cap->bus_info, XVIP_M2M_NAME, sizeof(cap->card));
+
+	return 0;
+}
+
+static int
+xvip_m2m_enum_fmt(struct file *file, void *fh, struct v4l2_fmtdesc *f)
+{
+	struct xvip_m2m_ctx *ctx = file2ctx(file);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	const struct xvip_video_format *fmtinfo;
+	const struct xvip_video_format *fmt;
+	struct v4l2_subdev *subdev;
+	struct v4l2_subdev_format v4l_fmt;
+	struct xvip_m2m_dev *xdev = ctx->xdev;
+	u32 i, fmt_cnt, *fmts;
+	int ret;
+
+	if (f->type != V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		ret = xilinx_xdma_get_v4l2_vid_fmts(dma->chan_rx,
+						    &fmt_cnt, &fmts);
+	else
+		ret = xilinx_xdma_get_v4l2_vid_fmts(dma->chan_tx,
+						    &fmt_cnt, &fmts);
+	if (ret)
+		return ret;
+
+	if (f->index >= fmt_cnt)
+		return -EINVAL;
+
+	if (!xdev->num_subdevs) {
+		fmt = xvip_get_format_by_fourcc(fmts[f->index]);
+		if (IS_ERR(fmt))
+			return PTR_ERR(fmt);
+
+		f->pixelformat = fmt->fourcc;
+		return 0;
+	}
+
+	if (f->index > 0)
+		return -EINVAL;
+
+	/* Establish media pad format */
+	if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		subdev = xvip_dma_remote_subdev(&dma->pads[XVIP_PAD_SOURCE],
+						&v4l_fmt.pad);
+	else
+		subdev = xvip_dma_remote_subdev(&dma->pads[XVIP_PAD_SINK],
+						&v4l_fmt.pad);
+	if (!subdev)
+		return -EPIPE;
+
+	v4l_fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+	ret = v4l2_subdev_call(subdev, pad, get_fmt, NULL, &v4l_fmt);
+	if (ret < 0)
+		return ret == -ENOIOCTLCMD ? -EINVAL : ret;
+
+	for (i = 0; i < fmt_cnt; i++) {
+		fmt = xvip_get_format_by_fourcc(fmts[i]);
+		if (IS_ERR(fmt))
+			return PTR_ERR(fmt);
+
+		if (fmt->code == v4l_fmt.format.code)
+			break;
+	}
+
+	if (i >= fmt_cnt)
+		return -EINVAL;
+
+	fmtinfo = xvip_get_format_by_fourcc(fmts[i]);
+	f->pixelformat = fmtinfo->fourcc;
+
+	return 0;
+}
+
+static int xvip_m2m_get_fmt(struct file *file, void *fh, struct v4l2_format *f)
+{
+	struct xvip_m2m_ctx *ctx = file2ctx(file);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct vb2_queue *vq;
+
+	vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx, f->type);
+	if (!vq)
+		return -EINVAL;
+
+	if (vq->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		f->fmt.pix_mp = dma->outfmt.fmt.pix_mp;
+	else
+		f->fmt.pix_mp = dma->capfmt.fmt.pix_mp;
+
+	return 0;
+}
+
+static int __xvip_m2m_try_fmt(struct xvip_m2m_ctx *ctx, struct v4l2_format *f)
+{
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	const struct xvip_video_format *info;
+	struct v4l2_pix_format_mplane *pix_mp;
+	struct v4l2_plane_pix_format *plane_fmt;
+	u32 align, min_width, max_width;
+	u32 bpl, min_bpl, max_bpl;
+	u32 padding_factor_nume, padding_factor_deno;
+	u32 bpl_nume, bpl_deno;
+	u32 i, plane_width, plane_height;
+	struct v4l2_subdev_format fmt;
+	struct v4l2_subdev *subdev;
+	struct xvip_m2m_dev *xdev = ctx->xdev;
+	int ret;
+
+	if (f->type != V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE &&
+	    f->type != V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		return -EINVAL;
+
+	if (xdev->num_subdevs) {
+		if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+			subdev = xvip_dma_remote_subdev
+				(&dma->pads[XVIP_PAD_SOURCE], &fmt.pad);
+		else
+			subdev = xvip_dma_remote_subdev
+				(&dma->pads[XVIP_PAD_SINK], &fmt.pad);
+
+		if (!subdev)
+			return -EPIPE;
+
+		fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
+		ret = v4l2_subdev_call(subdev, pad, get_fmt, NULL, &fmt);
+		if (ret < 0)
+			return -EINVAL;
+	}
+
+	pix_mp = &f->fmt.pix_mp;
+	plane_fmt = pix_mp->plane_fmt;
+	info = xvip_get_format_by_fourcc(f->fmt.pix_mp.pixelformat);
+	if (info) {
+		if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+			dma->outinfo = info;
+		else
+			dma->capinfo = info;
+	} else {
+		info = xvip_get_format_by_fourcc(XVIP_M2M_DEFAULT_FMT);
+	}
+
+	if (xdev->num_subdevs) {
+		if (info->code != fmt.format.code ||
+		    fmt.format.width != pix_mp->width ||
+		    fmt.format.height != pix_mp->height) {
+			dev_err(xdev->dev, "Failed to set format\n");
+			dev_info(xdev->dev,
+				 "Reqed Code = %d, Width = %d, Height = %d\n",
+				 info->code, pix_mp->width, pix_mp->height);
+			dev_info(xdev->dev,
+				 "Subdev Code = %d, Width = %d, Height = %d",
+				 fmt.format.code, fmt.format.width,
+				 fmt.format.height);
+			return -EINVAL;
+		}
+	}
+
+	xvip_width_padding_factor(info->fourcc, &padding_factor_nume,
+				  &padding_factor_deno);
+	xvip_bpl_scaling_factor(info->fourcc, &bpl_nume, &bpl_deno);
+
+	/*
+	 * V4L2 specification suggests the driver corrects the format struct
+	 * if any of the dimensions is unsupported
+	 */
+	align = lcm(dma->align, info->bpp >> 3);
+	min_width = roundup(XVIP_M2M_MIN_WIDTH, align);
+	max_width = rounddown(XVIP_M2M_MAX_WIDTH, align);
+	pix_mp->width = clamp(pix_mp->width, min_width, max_width);
+	pix_mp->height = clamp(pix_mp->height, XVIP_M2M_MIN_HEIGHT,
+			       XVIP_M2M_MAX_HEIGHT);
+
+	/*
+	 * Clamp the requested bytes per line value. If the maximum
+	 * bytes per line value is zero, the module doesn't support
+	 * user configurable line sizes. Override the requested value
+	 * with the minimum in that case.
+	 */
+	max_bpl = rounddown(XVIP_M2M_MAX_WIDTH, align);
+
+	if (info->buffers == 1) {
+		/* Handling contiguous data with mplanes */
+		min_bpl = (pix_mp->width * info->bpl_factor *
+			   padding_factor_nume * bpl_nume) /
+			   (padding_factor_deno * bpl_deno);
+		min_bpl = roundup(min_bpl, align);
+		bpl = roundup(plane_fmt[0].bytesperline, align);
+		plane_fmt[0].bytesperline = clamp(bpl, min_bpl, max_bpl);
+
+		if (info->num_planes == 1) {
+			/* Single plane formats */
+			plane_fmt[0].sizeimage = plane_fmt[0].bytesperline *
+						 pix_mp->height;
+		} else {
+			/* Multi plane formats in contiguous buffer*/
+			plane_fmt[0].sizeimage =
+				DIV_ROUND_UP(plane_fmt[0].bytesperline *
+					     pix_mp->height *
+					     info->bpp, 8);
+		}
+	} else {
+		/* Handling non-contiguous data with mplanes */
+		for (i = 0; i < info->num_planes; i++) {
+			plane_width = pix_mp->width / (i ? info->hsub : 1);
+			plane_height = pix_mp->height / (i ? info->vsub : 1);
+			min_bpl = (plane_width * info->bpl_factor *
+				   padding_factor_nume * bpl_nume) /
+				   (padding_factor_deno * bpl_deno);
+			min_bpl = roundup(min_bpl, align);
+			bpl = rounddown(plane_fmt[i].bytesperline, align);
+			plane_fmt[i].bytesperline = clamp(bpl, min_bpl,
+							  max_bpl);
+			plane_fmt[i].sizeimage = plane_fmt[i].bytesperline *
+						 plane_height;
+		}
+	}
+
+	return 0;
+}
+
+static int xvip_m2m_try_fmt(struct file *file, void *fh, struct v4l2_format *f)
+{
+	struct xvip_m2m_ctx *ctx = file2ctx(file);
+	int ret;
+
+	ret = __xvip_m2m_try_fmt(ctx, f);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int xvip_m2m_set_fmt(struct file *file, void *fh, struct v4l2_format *f)
+{
+	struct xvip_m2m_ctx *ctx = file2ctx(file);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct vb2_queue *vq;
+	int ret;
+
+	vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx, f->type);
+	if (!vq)
+		return -EINVAL;
+
+	if (vb2_is_busy(vq)) {
+		v4l2_err(&ctx->xdev->v4l2_dev, "%s queue busy\n", __func__);
+		return -EBUSY;
+	}
+
+	ret = __xvip_m2m_try_fmt(ctx, f);
+	if (ret < 0)
+		return ret;
+
+	if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		dma->outfmt.fmt.pix_mp = f->fmt.pix_mp;
+	else
+		dma->capfmt.fmt.pix_mp = f->fmt.pix_mp;
+
+	return 0;
+}
+
+static int
+xvip_m2m_g_selection(struct file *file, void *fh, struct v4l2_selection *s)
+{
+	struct xvip_m2m_ctx *ctx = file2ctx(file);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	int ret = 0;
+
+	if (s->type != V4L2_BUF_TYPE_VIDEO_OUTPUT &&
+	    s->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	switch (s->target) {
+	case V4L2_SEL_TGT_COMPOSE:
+		ret = -ENOTTY;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		s->r.left = 0;
+		s->r.top = 0;
+		s->r.width = dma->r.width;
+		s->r.height = dma->r.height;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static int
+xvip_m2m_s_selection(struct file *file, void *fh, struct v4l2_selection *s)
+{
+	struct xvip_m2m_ctx *ctx = file2ctx(file);
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	u32 min_width, max_width;
+	int ret = 0;
+
+	if (s->type != V4L2_BUF_TYPE_VIDEO_OUTPUT &&
+	    s->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	switch (s->target) {
+	case V4L2_SEL_TGT_COMPOSE:
+		ret = -ENOTTY;
+		break;
+	case V4L2_SEL_TGT_CROP:
+		if (s->r.width > dma->outfmt.fmt.pix_mp.width ||
+		    s->r.height > dma->outfmt.fmt.pix_mp.height ||
+		    s->r.top != 0 || s->r.left != 0)
+			return -EINVAL;
+
+		dma->crop = true;
+		min_width = roundup(XVIP_M2M_MIN_WIDTH, dma->align);
+		max_width = rounddown(XVIP_M2M_MAX_WIDTH, dma->align);
+		dma->r.width = clamp(s->r.width, min_width, max_width);
+		dma->r.height = s->r.height;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct v4l2_ioctl_ops xvip_m2m_ioctl_ops = {
+	.vidioc_querycap		= xvip_dma_querycap,
+
+	.vidioc_enum_fmt_vid_cap	= xvip_m2m_enum_fmt,
+	.vidioc_g_fmt_vid_cap_mplane	= xvip_m2m_get_fmt,
+	.vidioc_try_fmt_vid_cap_mplane	= xvip_m2m_try_fmt,
+	.vidioc_s_fmt_vid_cap_mplane	= xvip_m2m_set_fmt,
+
+	.vidioc_enum_fmt_vid_out	= xvip_m2m_enum_fmt,
+	.vidioc_g_fmt_vid_out_mplane	= xvip_m2m_get_fmt,
+	.vidioc_try_fmt_vid_out_mplane	= xvip_m2m_try_fmt,
+	.vidioc_s_fmt_vid_out_mplane	= xvip_m2m_set_fmt,
+	.vidioc_s_selection		= xvip_m2m_s_selection,
+	.vidioc_g_selection		= xvip_m2m_g_selection,
+
+	.vidioc_reqbufs			= v4l2_m2m_ioctl_reqbufs,
+	.vidioc_querybuf		= v4l2_m2m_ioctl_querybuf,
+	.vidioc_qbuf			= v4l2_m2m_ioctl_qbuf,
+	.vidioc_dqbuf			= v4l2_m2m_ioctl_dqbuf,
+	.vidioc_prepare_buf		= v4l2_m2m_ioctl_prepare_buf,
+	.vidioc_create_bufs		= v4l2_m2m_ioctl_create_bufs,
+	.vidioc_expbuf			= v4l2_m2m_ioctl_expbuf,
+
+	.vidioc_streamon		= v4l2_m2m_ioctl_streamon,
+	.vidioc_streamoff		= v4l2_m2m_ioctl_streamoff,
+};
+
+/*
+ * File operations
+ */
+static int xvip_m2m_open(struct file *file)
+{
+	struct xvip_m2m_dev *xdev = video_drvdata(file);
+	struct xvip_m2m_ctx *ctx = NULL;
+	int ret;
+
+	ctx = devm_kzalloc(xdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	v4l2_fh_init(&ctx->fh, video_devdata(file));
+	file->private_data = &ctx->fh;
+	ctx->xdev = xdev;
+
+	ctx->fh.m2m_ctx = v4l2_m2m_ctx_init(xdev->m2m_dev, ctx,
+					    &xvip_m2m_queue_init);
+	if (IS_ERR(ctx->fh.m2m_ctx)) {
+		ret = PTR_ERR(ctx->fh.m2m_ctx);
+		v4l2_fh_exit(&ctx->fh);
+		return ret;
+	}
+
+	v4l2_fh_add(&ctx->fh);
+	dev_info(xdev->dev, "Created instance %p, m2m_ctx: %p\n", ctx,
+		 ctx->fh.m2m_ctx);
+	return 0;
+}
+
+static int xvip_m2m_release(struct file *file)
+{
+	struct xvip_m2m_ctx *ctx = file->private_data;
+
+	v4l2_m2m_ctx_release(ctx->fh.m2m_ctx);
+	return 0;
+}
+
+static u32 xvip_m2m_poll(struct file *file,
+			 struct poll_table_struct *wait)
+{
+	struct xvip_m2m_ctx *ctx = file->private_data;
+	int ret;
+
+	mutex_lock(&ctx->xdev->lock);
+	ret = v4l2_m2m_poll(file, ctx->fh.m2m_ctx, wait);
+	mutex_unlock(&ctx->xdev->lock);
+
+	return ret;
+}
+
+static int xvip_m2m_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	struct xvip_m2m_ctx *ctx = file->private_data;
+
+	return v4l2_m2m_mmap(file, ctx->fh.m2m_ctx, vma);
+}
+
+/*
+ * mem2mem callbacks
+ */
+
+static int xvip_m2m_job_ready(void *priv)
+{
+	struct xvip_m2m_ctx *ctx = priv;
+
+	if ((v4l2_m2m_num_src_bufs_ready(ctx->fh.m2m_ctx) > 0) &&
+	    (v4l2_m2m_num_dst_bufs_ready(ctx->fh.m2m_ctx) > 0))
+		return 1;
+
+	return 0;
+}
+
+static void xvip_m2m_job_abort(void *priv)
+{
+	struct xvip_m2m_ctx *ctx = priv;
+
+	/* Will cancel the transaction in the next interrupt handler */
+	v4l2_m2m_job_finish(ctx->xdev->m2m_dev, ctx->fh.m2m_ctx);
+}
+
+static void xvip_m2m_prep_submit_dev2mem_desc(struct xvip_m2m_ctx *ctx,
+					      struct vb2_v4l2_buffer *dst_buf)
+{
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct xvip_m2m_dev *xdev = ctx->xdev;
+	struct dma_async_tx_descriptor *desc;
+	dma_addr_t p_out;
+	const struct xvip_video_format *info;
+	struct v4l2_pix_format_mplane *pix_mp;
+	u32 padding_factor_nume, padding_factor_deno;
+	u32 bpl_nume, bpl_deno;
+	u32 luma_size;
+	u32 flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
+	enum operation_mode mode = DEFAULT;
+	u32 bpl, dst_width, dst_height;
+
+	p_out = vb2_dma_contig_plane_dma_addr(&dst_buf->vb2_buf, 0);
+
+	if (!p_out) {
+		dev_err(xdev->dev,
+			"Acquiring kernel pointer to buffer failed\n");
+		return;
+	}
+
+	ctx->xt.dir = DMA_DEV_TO_MEM;
+	ctx->xt.src_sgl = false;
+	ctx->xt.dst_sgl = true;
+	ctx->xt.dst_start = p_out;
+
+	pix_mp = &dma->capfmt.fmt.pix_mp;
+	bpl = pix_mp->plane_fmt[0].bytesperline;
+	if (dma->crop) {
+		dst_width = dma->r.width;
+		dst_height = dma->r.height;
+	} else {
+		dst_width = pix_mp->width;
+		dst_height = pix_mp->height;
+	}
+
+	info = dma->capinfo;
+	xilinx_xdma_set_mode(dma->chan_rx, mode);
+	xilinx_xdma_v4l2_config(dma->chan_rx, pix_mp->pixelformat);
+	xvip_width_padding_factor(pix_mp->pixelformat, &padding_factor_nume,
+				  &padding_factor_deno);
+	xvip_bpl_scaling_factor(pix_mp->pixelformat, &bpl_nume, &bpl_deno);
+
+	ctx->xt.frame_size = info->num_planes;
+	ctx->sgl[0].size = (dst_width * info->bpl_factor *
+			    padding_factor_nume * bpl_nume) /
+			    (padding_factor_deno * bpl_deno);
+	ctx->sgl[0].icg = bpl - ctx->sgl[0].size;
+	ctx->xt.numf = dst_height;
+
+	/*
+	 * dst_icg is the number of bytes to jump after last luma addr
+	 * and before first chroma addr
+	 */
+	ctx->sgl[0].src_icg = 0;
+
+	if (info->buffers == 1) {
+		/* Handling contiguous data with mplanes */
+		ctx->sgl[0].dst_icg = 0;
+		if (dma->crop)
+			ctx->sgl[0].dst_icg = bpl *
+					      (pix_mp->height - dst_height);
+	} else {
+		/* Handling non-contiguous data with mplanes */
+		if (info->buffers == 2) {
+			dma_addr_t chroma_cap =
+			vb2_dma_contig_plane_dma_addr(&dst_buf->vb2_buf, 1);
+			luma_size = pix_mp->plane_fmt[0].bytesperline *
+				    ctx->xt.numf;
+			if (chroma_cap > p_out)
+				ctx->sgl[0].dst_icg = chroma_cap - p_out -
+						      luma_size;
+			}
+	}
+
+	desc = dmaengine_prep_interleaved_dma(dma->chan_rx, &ctx->xt, flags);
+	if (!desc) {
+		dev_err(xdev->dev, "Failed to prepare DMA rx transfer\n");
+		return;
+	}
+
+	desc->callback = xvip_m2m_dma_callback;
+	desc->callback_param = ctx;
+	dmaengine_submit(desc);
+	dma_async_issue_pending(dma->chan_rx);
+}
+
+static void xvip_m2m_prep_submit_mem2dev_desc(struct xvip_m2m_ctx *ctx,
+					      struct vb2_v4l2_buffer *src_buf)
+{
+	struct xvip_m2m_dma *dma = ctx->xdev->dma;
+	struct xvip_m2m_dev *xdev = ctx->xdev;
+	struct dma_async_tx_descriptor *desc;
+	dma_addr_t p_in;
+	const struct xvip_video_format *info;
+	struct v4l2_pix_format_mplane *pix_mp;
+	u32 padding_factor_nume, padding_factor_deno;
+	u32 bpl_nume, bpl_deno;
+	u32 luma_size;
+	u32 flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
+	enum operation_mode mode = DEFAULT;
+	u32 bpl, src_width, src_height;
+
+	p_in = vb2_dma_contig_plane_dma_addr(&src_buf->vb2_buf, 0);
+
+	if (!p_in) {
+		dev_err(xdev->dev,
+			"Acquiring kernel pointer to buffer failed\n");
+		return;
+	}
+
+	ctx->xt.dir = DMA_MEM_TO_DEV;
+	ctx->xt.src_sgl = true;
+	ctx->xt.dst_sgl = false;
+	ctx->xt.src_start = p_in;
+
+	pix_mp = &dma->outfmt.fmt.pix_mp;
+	bpl = pix_mp->plane_fmt[0].bytesperline;
+	if (dma->crop) {
+		src_width = dma->r.width;
+		src_height = dma->r.height;
+	} else {
+		src_width = pix_mp->width;
+		src_height = pix_mp->height;
+	}
+
+	info = dma->outinfo;
+	xilinx_xdma_set_mode(dma->chan_tx, mode);
+	xilinx_xdma_v4l2_config(dma->chan_tx, pix_mp->pixelformat);
+	xvip_width_padding_factor(pix_mp->pixelformat, &padding_factor_nume,
+				  &padding_factor_deno);
+	xvip_bpl_scaling_factor(pix_mp->pixelformat, &bpl_nume, &bpl_deno);
+
+	ctx->xt.frame_size = info->num_planes;
+	ctx->sgl[0].size = (src_width * info->bpl_factor *
+			    padding_factor_nume * bpl_nume) /
+			    (padding_factor_deno * bpl_deno);
+	ctx->sgl[0].icg = bpl - ctx->sgl[0].size;
+	ctx->xt.numf = src_height;
+
+	/*
+	 * src_icg is the number of bytes to jump after last luma addr
+	 * and before first chroma addr
+	 */
+	ctx->sgl[0].dst_icg = 0;
+
+	if (info->buffers == 1) {
+		/* Handling contiguous data with mplanes */
+		ctx->sgl[0].src_icg = 0;
+		if (dma->crop)
+			ctx->sgl[0].src_icg = bpl *
+					      (pix_mp->height - src_height);
+	} else {
+		/* Handling non-contiguous data with mplanes */
+		if (info->buffers == 2) {
+			dma_addr_t chroma_out =
+			vb2_dma_contig_plane_dma_addr(&src_buf->vb2_buf, 1);
+			luma_size = bpl * ctx->xt.numf;
+			if (chroma_out > p_in)
+				ctx->sgl[0].src_icg = chroma_out - p_in -
+						      luma_size;
+			}
+	}
+
+	desc = dmaengine_prep_interleaved_dma(dma->chan_tx, &ctx->xt, flags);
+	if (!desc) {
+		dev_err(xdev->dev, "Failed to prepare DMA tx transfer\n");
+		return;
+	}
+
+	desc->callback = xvip_m2m_dma_callback_mem2dev;
+	desc->callback_param = ctx;
+	dmaengine_submit(desc);
+	dma_async_issue_pending(dma->chan_tx);
+}
+
+/**
+ * xvip_m2m_device_run - prepares and starts the device
+ *
+ * @priv: Instance private data
+ *
+ * This simulates all the immediate preparations required before starting
+ * a device. This will be called by the framework when it decides to schedule
+ * a particular instance.
+ */
+static void xvip_m2m_device_run(void *priv)
+{
+	struct xvip_m2m_ctx *ctx = priv;
+	struct vb2_v4l2_buffer *src_buf, *dst_buf;
+
+	src_buf = v4l2_m2m_next_src_buf(ctx->fh.m2m_ctx);
+	dst_buf = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx);
+
+	/* Prepare and submit mem2dev transaction */
+	xvip_m2m_prep_submit_mem2dev_desc(ctx, src_buf);
+
+	/* Prepare and submit dev2mem transaction */
+	xvip_m2m_prep_submit_dev2mem_desc(ctx, dst_buf);
+}
+
+static const struct v4l2_file_operations xvip_m2m_fops = {
+	.owner		= THIS_MODULE,
+	.open		= xvip_m2m_open,
+	.release	= xvip_m2m_release,
+	.poll		= xvip_m2m_poll,
+	.unlocked_ioctl	= video_ioctl2,
+	.mmap		= xvip_m2m_mmap,
+};
+
+static struct video_device xvip_m2m_videodev = {
+	.name		= XVIP_M2M_NAME,
+	.fops		= &xvip_m2m_fops,
+	.ioctl_ops	= &xvip_m2m_ioctl_ops,
+	.release	= video_device_release_empty,
+	.vfl_dir	= VFL_DIR_M2M,
+	.device_caps	= V4L2_CAP_VIDEO_M2M_MPLANE | V4L2_CAP_STREAMING,
+	.vfl_type	= VFL_TYPE_VIDEO,
+};
+
+static const struct v4l2_m2m_ops xvip_m2m_ops = {
+	.device_run	= xvip_m2m_device_run,
+	.job_ready	= xvip_m2m_job_ready,
+	.job_abort	= xvip_m2m_job_abort,
+};
+
+/*
+ * This function is taken from the framework
+ * video_register_media_controller() function
+ */
+static int xvideo_register_media_controller(struct video_device *vdev)
+{
+#if defined(CONFIG_MEDIA_CONTROLLER)
+	u32 intf_type;
+	int ret;
+
+	/*
+	 * Modified this by removing the condition for VFL_DIR_M2M
+	 * to ensure that the video entity is created.
+	 */
+	if (!vdev->v4l2_dev->mdev)
+		return 0;
+
+	vdev->entity.obj_type = MEDIA_ENTITY_TYPE_VIDEO_DEVICE;
+	vdev->entity.function = MEDIA_ENT_F_UNKNOWN;
+
+	switch (vdev->vfl_type) {
+	case VFL_TYPE_VIDEO:
+		intf_type = MEDIA_INTF_T_V4L_VIDEO;
+		vdev->entity.function = MEDIA_ENT_F_IO_V4L;
+		break;
+	case VFL_TYPE_VBI:
+		intf_type = MEDIA_INTF_T_V4L_VBI;
+		vdev->entity.function = MEDIA_ENT_F_IO_VBI;
+		break;
+	case VFL_TYPE_SDR:
+		intf_type = MEDIA_INTF_T_V4L_SWRADIO;
+		vdev->entity.function = MEDIA_ENT_F_IO_SWRADIO;
+		break;
+	case VFL_TYPE_TOUCH:
+		intf_type = MEDIA_INTF_T_V4L_TOUCH;
+		vdev->entity.function = MEDIA_ENT_F_IO_V4L;
+		break;
+	case VFL_TYPE_RADIO:
+		intf_type = MEDIA_INTF_T_V4L_RADIO;
+		/*
+		 * Radio doesn't have an entity at the V4L2 side to represent
+		 * radio input or output. Instead, the audio input/output goes
+		 * via either physical wires or ALSA.
+		 */
+		break;
+	case VFL_TYPE_SUBDEV:
+		intf_type = MEDIA_INTF_T_V4L_SUBDEV;
+		/* Entity will be created via v4l2_device_register_subdev() */
+		break;
+	default:
+		return 0;
+	}
+
+	if (vdev->entity.function != MEDIA_ENT_F_UNKNOWN) {
+		vdev->entity.name = vdev->name;
+
+		/* Needed just for backward compatibility with legacy MC API */
+		vdev->entity.info.dev.major = VIDEO_MAJOR;
+		vdev->entity.info.dev.minor = vdev->minor;
+
+		ret = media_device_register_entity(vdev->v4l2_dev->mdev,
+						   &vdev->entity);
+		if (ret < 0) {
+			pr_warn("%s: media_device_register_entity failed\n",
+				__func__);
+			return ret;
+		}
+	}
+
+	vdev->intf_devnode = media_devnode_create(vdev->v4l2_dev->mdev,
+						  intf_type,
+						  0, VIDEO_MAJOR,
+						  vdev->minor);
+	if (!vdev->intf_devnode) {
+		media_device_unregister_entity(&vdev->entity);
+		return -ENOMEM;
+	}
+
+	if (vdev->entity.function != MEDIA_ENT_F_UNKNOWN) {
+		struct media_link *link;
+
+		link = media_create_intf_link(&vdev->entity,
+					      &vdev->intf_devnode->intf,
+					      MEDIA_LNK_FL_ENABLED |
+					      MEDIA_LNK_FL_IMMUTABLE);
+		if (!link) {
+			media_devnode_remove(vdev->intf_devnode);
+			media_device_unregister_entity(&vdev->entity);
+			return -ENOMEM;
+		}
+	}
+
+	/* FIXME: how to create the other interface links? */
+
+#endif
+	/* This is added from __video_register_device() */
+
+	/* Part 6: Activate this minor. The char device can now be used. */
+	set_bit(V4L2_FL_REGISTERED, &vdev->flags);
+
+	return 0;
+}
+
+static int xvip_m2m_dma_init(struct xvip_m2m_dma *dma)
+{
+	struct xvip_m2m_dev *xdev;
+	struct v4l2_pix_format_mplane *pix_mp;
+	int ret;
+
+	xdev = dma->xdev;
+	mutex_init(&xdev->lock);
+	mutex_init(&dma->pipe.lock);
+	spin_lock_init(&xdev->queued_lock);
+
+	/* Format info on capture port - NV12 is the default format */
+	dma->capinfo = xvip_get_format_by_fourcc(XVIP_M2M_DEFAULT_FMT);
+	pix_mp = &dma->capfmt.fmt.pix_mp;
+	pix_mp->pixelformat = dma->capinfo->fourcc;
+
+	pix_mp->field = V4L2_FIELD_NONE;
+	pix_mp->width = XVIP_M2M_DEF_WIDTH;
+	pix_mp->height = XVIP_M2M_DEF_HEIGHT;
+	pix_mp->plane_fmt[0].bytesperline = pix_mp->width *
+					    dma->capinfo->bpl_factor;
+	pix_mp->plane_fmt[0].sizeimage =
+			DIV_ROUND_UP(pix_mp->plane_fmt[0].bytesperline *
+				     pix_mp->height * dma->capinfo->bpp, 8);
+
+	/* Format info on output port - NV12 is the default format */
+	dma->outinfo = xvip_get_format_by_fourcc(XVIP_M2M_DEFAULT_FMT);
+	pix_mp = &dma->capfmt.fmt.pix_mp;
+	pix_mp->pixelformat = dma->outinfo->fourcc;
+	pix_mp->field = V4L2_FIELD_NONE;
+	pix_mp->width = XVIP_M2M_DEF_WIDTH;
+	pix_mp->height = XVIP_M2M_DEF_HEIGHT;
+	pix_mp->plane_fmt[0].bytesperline = pix_mp->width *
+					    dma->outinfo->bpl_factor;
+	pix_mp->plane_fmt[0].sizeimage =
+			DIV_ROUND_UP(pix_mp->plane_fmt[0].bytesperline *
+				     pix_mp->height * dma->outinfo->bpp, 8);
+
+	/* DMA channels for mem2mem */
+	dma->chan_tx = dma_request_chan(xdev->dev, "tx");
+	if (IS_ERR(dma->chan_tx)) {
+		ret = PTR_ERR(dma->chan_tx);
+		if (ret != -EPROBE_DEFER)
+			dev_err(xdev->dev, "mem2mem DMA tx channel not found");
+
+		return ret;
+	}
+
+	dma->chan_rx = dma_request_chan(xdev->dev, "rx");
+	if (IS_ERR(dma->chan_rx)) {
+		ret = PTR_ERR(dma->chan_rx);
+		if (ret != -EPROBE_DEFER)
+			dev_err(xdev->dev, "mem2mem DMA rx channel not found");
+
+		goto tx;
+	}
+
+	dma->align = BIT(dma->chan_tx->device->copy_align);
+
+	/* Video node */
+	dma->video = xvip_m2m_videodev;
+	dma->video.v4l2_dev = &xdev->v4l2_dev;
+	dma->video.lock = &xdev->lock;
+
+	dma->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	dma->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	ret = media_entity_pads_init(&dma->video.entity, 2, dma->pads);
+	if (ret < 0)
+		goto error;
+
+	ret = video_register_device(&dma->video, VFL_TYPE_VIDEO, -1);
+	if (ret < 0) {
+		dev_err(xdev->dev, "Failed to register mem2mem video device\n");
+		goto tx_rx;
+	}
+
+	ret = xvideo_register_media_controller(&dma->video);
+	if (ret < 0) {
+		dev_err(xdev->dev, "Failed to register media controller\n");
+		goto unreg_video;
+	}
+
+	video_set_drvdata(&dma->video, dma->xdev);
+	return 0;
+
+unreg_video:
+	video_unregister_device(&dma->video);
+tx_rx:
+	dma_release_channel(dma->chan_rx);
+tx:
+	dma_release_channel(dma->chan_tx);
+error:
+	return ret;
+}
+
+static void xvip_m2m_dma_deinit(struct xvip_m2m_dma *dma)
+{
+	if (video_is_registered(&dma->video))
+		video_unregister_device(&dma->video);
+
+	mutex_destroy(&dma->pipe.lock);
+	mutex_destroy(&dma->xdev->lock);
+	dma_release_channel(dma->chan_tx);
+	dma_release_channel(dma->chan_rx);
+}
+
+static int xvip_m2m_dma_alloc_init(struct xvip_m2m_dev *xdev)
+{
+	struct xvip_m2m_dma *dma = NULL;
+	int ret;
+
+	dma = devm_kzalloc(xdev->dev, sizeof(*dma), GFP_KERNEL);
+	if (!dma)
+		return -ENOMEM;
+
+	dma->xdev = xdev;
+	xdev->dma = dma;
+
+	ret = xvip_m2m_dma_init(xdev->dma);
+	if (ret) {
+		dev_err(xdev->dev, "DMA initialization failed\n");
+		devm_kfree(xdev->dev, dma);
+		xdev->dma = NULL;
+		return ret;
+	}
+
+	xdev->v4l2_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_M2M_MPLANE;
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+static void xvip_composite_v4l2_cleanup(struct xvip_m2m_dev *xdev)
+{
+	v4l2_device_unregister(&xdev->v4l2_dev);
+	media_device_unregister(&xdev->media_dev);
+	media_device_cleanup(&xdev->media_dev);
+}
+
+static int xvip_composite_v4l2_init(struct xvip_m2m_dev *xdev)
+{
+	int ret;
+
+	xdev->media_dev.dev = xdev->dev;
+	strlcpy(xdev->media_dev.model, "Xilinx Video M2M Composite Device",
+		sizeof(xdev->media_dev.model));
+	xdev->media_dev.hw_revision = 0;
+
+	media_device_init(&xdev->media_dev);
+
+	xdev->v4l2_dev.mdev = &xdev->media_dev;
+	ret = v4l2_device_register(xdev->dev, &xdev->v4l2_dev);
+	if (ret < 0) {
+		dev_err(xdev->dev, "V4L2 device registration failed (%d)\n",
+			ret);
+		media_device_cleanup(&xdev->media_dev);
+		return ret;
+	}
+
+	return 0;
+}
+
+static struct xvip_graph_entity *
+xvip_graph_find_entity(struct xvip_m2m_dev *xdev,
+		       const struct device_node *node)
+{
+	struct xvip_graph_entity *entity;
+
+	list_for_each_entry(entity, &xdev->entities, list) {
+		if (entity->node == node)
+			return entity;
+	}
+
+	return NULL;
+}
+
+static int xvip_graph_build_one(struct xvip_m2m_dev *xdev,
+				struct xvip_graph_entity *entity)
+{
+	u32 link_flags = MEDIA_LNK_FL_ENABLED;
+	struct media_entity *local = entity->entity;
+	struct media_entity *remote;
+	struct media_pad *local_pad;
+	struct media_pad *remote_pad;
+	struct xvip_graph_entity *ent;
+	struct v4l2_fwnode_link link;
+	struct device_node *ep = NULL;
+	struct device_node *next;
+	int ret = 0;
+
+	dev_dbg(xdev->dev, "creating links for entity %s\n", local->name);
+
+	while (1) {
+		/* Get the next endpoint and parse its link. */
+		next = of_graph_get_next_endpoint(entity->node, ep);
+		if (!next)
+			break;
+
+		ep = next;
+
+		dev_dbg(xdev->dev, "processing endpoint %pOF\n", ep);
+
+		ret = v4l2_fwnode_parse_link(of_fwnode_handle(ep), &link);
+		if (ret < 0) {
+			dev_err(xdev->dev, "failed to parse link for %pOF\n",
+				ep);
+			continue;
+		}
+
+		/* Skip sink ports, they will be processed from the other end of
+		 * the link.
+		 */
+		if (link.local_port >= local->num_pads) {
+			dev_err(xdev->dev, "invalid port number %u for %pOF\n",
+				link.local_port,
+				to_of_node(link.local_node));
+			v4l2_fwnode_put_link(&link);
+			ret = -EINVAL;
+			break;
+		}
+
+		local_pad = &local->pads[link.local_port];
+
+		if (local_pad->flags & MEDIA_PAD_FL_SINK) {
+			dev_dbg(xdev->dev, "skipping sink port %pOF:%u\n",
+				to_of_node(link.local_node),
+				link.local_port);
+			v4l2_fwnode_put_link(&link);
+			continue;
+		}
+
+		/* Skip DMA engines, they will be processed separately. */
+		if (link.remote_node == of_fwnode_handle(xdev->dev->of_node)) {
+			dev_dbg(xdev->dev, "skipping DMA port %pOF:%u\n",
+				to_of_node(link.local_node),
+				link.local_port);
+			v4l2_fwnode_put_link(&link);
+			continue;
+		}
+
+		/* Find the remote entity. */
+		ent = xvip_graph_find_entity(xdev,
+					     to_of_node(link.remote_node));
+		if (!ent) {
+			dev_err(xdev->dev, "no entity found for %pOF\n",
+				to_of_node(link.remote_node));
+			v4l2_fwnode_put_link(&link);
+			ret = -ENODEV;
+			break;
+		}
+
+		remote = ent->entity;
+
+		if (link.remote_port >= remote->num_pads) {
+			dev_err(xdev->dev, "invalid port number %u on %pOF\n",
+				link.remote_port, to_of_node(link.remote_node));
+			v4l2_fwnode_put_link(&link);
+			ret = -EINVAL;
+			break;
+		}
+
+		remote_pad = &remote->pads[link.remote_port];
+
+		v4l2_fwnode_put_link(&link);
+
+		/* Create the media link. */
+		dev_dbg(xdev->dev, "creating %s:%u -> %s:%u link\n",
+			local->name, local_pad->index,
+			remote->name, remote_pad->index);
+
+		ret = media_create_pad_link(local, local_pad->index,
+					    remote, remote_pad->index,
+					    link_flags);
+		if (ret < 0) {
+			dev_err(xdev->dev,
+				"failed to create %s:%u -> %s:%u link\n",
+				local->name, local_pad->index,
+				remote->name, remote_pad->index);
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int xvip_graph_parse_one(struct xvip_m2m_dev *xdev,
+				struct device_node *node)
+{
+	struct xvip_graph_entity *entity;
+	struct device_node *remote;
+	struct device_node *ep = NULL;
+	int ret = 0;
+
+	dev_dbg(xdev->dev, "parsing node %pOF\n", node);
+
+	while (1) {
+		ep = of_graph_get_next_endpoint(node, ep);
+		if (!ep)
+			break;
+
+		dev_dbg(xdev->dev, "handling endpoint %pOF %s\n",
+			ep, ep->name);
+
+		remote = of_graph_get_remote_port_parent(ep);
+		if (!remote) {
+			ret = -EINVAL;
+			break;
+		}
+		dev_dbg(xdev->dev, "Remote endpoint %pOF %s\n",
+			remote, remote->name);
+
+		/* Skip entities that we have already processed. */
+		if (remote == xdev->dev->of_node ||
+		    xvip_graph_find_entity(xdev, remote)) {
+			of_node_put(remote);
+			continue;
+		}
+
+		entity = devm_kzalloc(xdev->dev, sizeof(*entity), GFP_KERNEL);
+		if (!entity) {
+			of_node_put(remote);
+			ret = -ENOMEM;
+			break;
+		}
+
+		entity->node = remote;
+		entity->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
+		entity->asd.match.fwnode = of_fwnode_handle(remote);
+		list_add_tail(&entity->list, &xdev->entities);
+		xdev->num_subdevs++;
+	}
+
+	of_node_put(ep);
+	return ret;
+}
+
+static int xvip_graph_parse(struct xvip_m2m_dev *xdev)
+{
+	struct xvip_graph_entity *entity;
+	int ret;
+
+	/*
+	 * Walk the links to parse the full graph. Start by parsing the
+	 * composite node and then parse entities in turn. The list_for_each
+	 * loop will handle entities added at the end of the list while walking
+	 * the links.
+	 */
+	ret = xvip_graph_parse_one(xdev, xdev->dev->of_node);
+	if (ret < 0)
+		return 0;
+
+	list_for_each_entry(entity, &xdev->entities, list) {
+		ret = xvip_graph_parse_one(xdev, entity->node);
+		if (ret < 0)
+			break;
+	}
+
+	return ret;
+}
+
+static int xvip_graph_build_dma(struct xvip_m2m_dev *xdev)
+{
+	u32 link_flags = MEDIA_LNK_FL_ENABLED;
+	struct device_node *node = xdev->dev->of_node;
+	struct media_entity *source;
+	struct media_entity *sink;
+	struct media_pad *source_pad;
+	struct media_pad *sink_pad;
+	struct xvip_graph_entity *ent;
+	struct v4l2_fwnode_link link;
+	struct device_node *ep = NULL;
+	struct device_node *next;
+	struct xvip_m2m_dma *dma = xdev->dma;
+	int ret = 0;
+
+	dev_dbg(xdev->dev, "creating links for DMA engines\n");
+
+	while (1) {
+		/* Get the next endpoint and parse its link. */
+		next = of_graph_get_next_endpoint(node, ep);
+		if (!next)
+			break;
+
+		ep = next;
+
+		dev_dbg(xdev->dev, "processing endpoint %pOF\n", ep);
+
+		ret = v4l2_fwnode_parse_link(of_fwnode_handle(ep), &link);
+		if (ret < 0) {
+			dev_err(xdev->dev, "failed to parse link for %pOF\n",
+				ep);
+			continue;
+		}
+
+		dev_dbg(xdev->dev, "creating link for DMA engine %s\n",
+			dma->video.name);
+
+		/* Find the remote entity. */
+		ent = xvip_graph_find_entity(xdev,
+					     to_of_node(link.remote_node));
+		if (!ent) {
+			dev_err(xdev->dev, "no entity found for %pOF\n",
+				to_of_node(link.remote_node));
+			v4l2_fwnode_put_link(&link);
+			ret = -ENODEV;
+			break;
+		}
+		if (link.remote_port >= ent->entity->num_pads) {
+			dev_err(xdev->dev, "invalid port number %u on %pOF\n",
+				link.remote_port,
+				to_of_node(link.remote_node));
+			v4l2_fwnode_put_link(&link);
+			ret = -EINVAL;
+			break;
+		}
+
+		dev_dbg(xdev->dev, "Entity %s %s\n", ent->node->name,
+			ent->node->full_name);
+		dev_dbg(xdev->dev, "port number %u on %pOF\n",
+			link.remote_port, to_of_node(link.remote_node));
+		dev_dbg(xdev->dev, "local port number %u on %pOF\n",
+			link.local_port, to_of_node(link.local_node));
+
+		if (link.local_port == XVIP_PAD_SOURCE) {
+			source = &dma->video.entity;
+			source_pad = &dma->pads[XVIP_PAD_SOURCE];
+			sink = ent->entity;
+			sink_pad = &sink->pads[XVIP_PAD_SINK];
+
+		} else {
+			source = ent->entity;
+			source_pad = &source->pads[XVIP_PAD_SOURCE];
+			sink = &dma->video.entity;
+			sink_pad = &dma->pads[XVIP_PAD_SINK];
+		}
+
+		v4l2_fwnode_put_link(&link);
+
+		/* Create the media link. */
+		dev_dbg(xdev->dev, "creating %s:%u -> %s:%u link\n",
+			source->name, source_pad->index,
+			sink->name, sink_pad->index);
+
+		ret = media_create_pad_link(source, source_pad->index,
+					    sink, sink_pad->index,
+					    link_flags);
+		if (ret < 0) {
+			dev_err(xdev->dev,
+				"failed to create %s:%u -> %s:%u link\n",
+				source->name, source_pad->index,
+				sink->name, sink_pad->index);
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int xvip_graph_notify_complete(struct v4l2_async_notifier *notifier)
+{
+	struct xvip_m2m_dev *xdev =
+		container_of(notifier, struct xvip_m2m_dev, notifier);
+	struct xvip_graph_entity *entity;
+	int ret;
+
+	dev_dbg(xdev->dev, "notify complete, all subdevs registered\n");
+
+	/* Create links for every entity. */
+	list_for_each_entry(entity, &xdev->entities, list) {
+		ret = xvip_graph_build_one(xdev, entity);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* Create links for DMA channels. */
+	ret = xvip_graph_build_dma(xdev);
+	if (ret < 0)
+		return ret;
+
+	ret = v4l2_device_register_subdev_nodes(&xdev->v4l2_dev);
+	if (ret < 0)
+		dev_err(xdev->dev, "failed to register subdev nodes\n");
+
+	return media_device_register(&xdev->media_dev);
+}
+
+static int xvip_graph_notify_bound(struct v4l2_async_notifier *notifier,
+				   struct v4l2_subdev *subdev,
+				   struct v4l2_async_subdev *asd)
+{
+	struct xvip_m2m_dev *xdev =
+		container_of(notifier, struct xvip_m2m_dev, notifier);
+	struct xvip_graph_entity *entity;
+
+	/* Locate the entity corresponding to the bound subdev and store the
+	 * subdev pointer.
+	 */
+	list_for_each_entry(entity, &xdev->entities, list) {
+		if (entity->node != subdev->dev->of_node)
+			continue;
+
+		if (entity->subdev) {
+			dev_err(xdev->dev, "duplicate subdev for node %pOF\n",
+				entity->node);
+			return -EINVAL;
+		}
+
+		dev_dbg(xdev->dev, "subdev %s bound\n", subdev->name);
+		entity->entity = &subdev->entity;
+		entity->subdev = subdev;
+		return 0;
+	}
+
+	dev_err(xdev->dev, "no entity for subdev %s\n", subdev->name);
+	return -EINVAL;
+}
+
+static const struct v4l2_async_notifier_operations xvip_graph_notify_ops = {
+	.bound = xvip_graph_notify_bound,
+	.complete = xvip_graph_notify_complete,
+};
+
+static void xvip_graph_cleanup(struct xvip_m2m_dev *xdev)
+{
+	struct xvip_graph_entity *entityp;
+	struct xvip_graph_entity *entity;
+
+	if (xdev->dma)
+		xvip_m2m_dma_deinit(xdev->dma);
+	v4l2_async_notifier_cleanup(&xdev->notifier);
+	v4l2_async_notifier_unregister(&xdev->notifier);
+
+	list_for_each_entry_safe(entity, entityp, &xdev->entities, list) {
+		of_node_put(entity->node);
+		list_del(&entity->list);
+	}
+}
+
+static int xvip_graph_init(struct xvip_m2m_dev *xdev)
+{
+	struct xvip_graph_entity *entity;
+	int ret;
+
+	/* Init the DMA channels. */
+	ret = xvip_m2m_dma_alloc_init(xdev);
+	if (ret < 0) {
+		dev_err(xdev->dev, "DMA initialization failed\n");
+		goto done;
+	}
+
+	/* Parse the graph to extract a list of subdevice DT nodes. */
+	ret = xvip_graph_parse(xdev);
+	if (ret < 0) {
+		dev_err(xdev->dev, "graph parsing failed\n");
+		goto done;
+	}
+	dev_dbg(xdev->dev, "Number of subdev = %d\n", xdev->num_subdevs);
+
+	if (!xdev->num_subdevs) {
+		dev_err(xdev->dev, "no subdev found in graph\n");
+		goto done;
+	}
+
+	/* Register the subdevices notifier. */
+	list_for_each_entry(entity, &xdev->entities, list) {
+		ret = __v4l2_async_notifier_add_subdev(&xdev->notifier,
+						       &entity->asd);
+		if (ret)
+			goto done;
+	}
+
+	xdev->notifier.ops = &xvip_graph_notify_ops;
+
+	ret = v4l2_async_notifier_register(&xdev->v4l2_dev, &xdev->notifier);
+	if (ret < 0) {
+		dev_err(xdev->dev, "notifier registration failed\n");
+		goto done;
+	}
+
+	ret = 0;
+
+done:
+	if (ret < 0)
+		xvip_graph_cleanup(xdev);
+
+	return ret;
+}
+
+static int xvip_composite_remove(struct platform_device *pdev)
+{
+	struct xvip_m2m_dev *xdev = platform_get_drvdata(pdev);
+
+	xvip_graph_cleanup(xdev);
+	xvip_composite_v4l2_cleanup(xdev);
+
+	return 0;
+}
+
+static int xvip_m2m_probe(struct platform_device *pdev)
+{
+	struct xvip_m2m_dev *xdev = NULL;
+	int ret;
+
+	xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL);
+	if (!xdev)
+		return -ENOMEM;
+
+	xdev->dev = &pdev->dev;
+	INIT_LIST_HEAD(&xdev->entities);
+	v4l2_async_notifier_init(&xdev->notifier);
+
+	ret = xvip_composite_v4l2_init(xdev);
+	if (ret)
+		return -EINVAL;
+
+	xdev->m2m_dev = v4l2_m2m_init(&xvip_m2m_ops);
+	if (IS_ERR(xdev->m2m_dev)) {
+		dev_err(xdev->dev, "Failed to init mem2mem device\n");
+		return PTR_ERR(xdev->m2m_dev);
+	}
+
+	ret = xvip_graph_init(xdev);
+	if (ret < 0)
+		goto error;
+
+	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
+	if (ret) {
+		dev_err(&pdev->dev, "dma_set_coherent_mask: %d\n", ret);
+		goto dma_cleanup;
+	}
+
+	platform_set_drvdata(pdev, xdev);
+
+	dev_info(xdev->dev, "mem2mem device registered\n");
+	return 0;
+
+dma_cleanup:
+	xvip_m2m_dma_deinit(xdev->dma);
+
+error:
+	v4l2_device_unregister(&xdev->v4l2_dev);
+	return ret;
+}
+
+static int xvip_m2m_remove(struct platform_device *pdev)
+{
+	xvip_composite_remove(pdev);
+	return 0;
+}
+
+static const struct of_device_id xvip_m2m_of_id_table[] = {
+	{ .compatible = "xlnx,mem2mem" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xvip_m2m_of_id_table);
+
+static struct platform_driver xvip_m2m_driver = {
+	.driver = {
+		.name = XVIP_M2M_NAME,
+		.of_match_table = xvip_m2m_of_id_table,
+	},
+	.probe = xvip_m2m_probe,
+	.remove = xvip_m2m_remove,
+};
+
+module_platform_driver(xvip_m2m_driver);
+
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("Xilinx V4L2 mem2mem driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-multi-scaler-coeff.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-multi-scaler-coeff.h
@@ -0,0 +1,574 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx Memory-to-Memory Video Multi-Scaler IP
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Author: Suresh Gupta <sureshg@xilinx.com>
+ *
+ * The file contains the coefficients used by the Xilinx
+ * Video Multi Scaler Controller driver (xm2msc)
+ *
+ */
+
+#define XSCALER_MAX_PHASES	(64)
+#define XSCALER_MAX_TAPS	(12)
+
+#define XSCALER_TAPS_6		(6)
+#define XSCALER_TAPS_8		(8)
+#define XSCALER_TAPS_10		(10)
+#define XSCALER_TAPS_12		(12)
+
+/* Filter bank ID for various filter tap configurations */
+enum xm2mvsc_filter_bank_id {
+	FILTER_BANK_TAPS_6 = 0,
+	FILTER_BANK_TAPS_8,
+	FILTER_BANK_TAPS_10,
+	FILTER_BANK_TAPS_12,
+};
+
+/* H-scaler coefficients for 6, 8, 10 and 12 tap filters */
+static const short
+xhsc_coeff_taps6[XSCALER_MAX_PHASES][XSCALER_TAPS_6] = {
+	{  -132,   236,  3824,   236,  -132,    64, },
+	{  -116,   184,  3816,   292,  -144,    64, },
+	{  -100,   132,  3812,   348,  -160,    64, },
+	{   -88,    84,  3808,   404,  -176,    64, },
+	{   -72,    36,  3796,   464,  -192,    64, },
+	{   -60,    -8,  3780,   524,  -208,    68, },
+	{   -48,   -52,  3768,   588,  -228,    68, },
+	{   -32,   -96,  3748,   652,  -244,    68, },
+	{   -20,  -136,  3724,   716,  -260,    72, },
+	{    -8,  -172,  3696,   784,  -276,    72, },
+	{     0,  -208,  3676,   848,  -292,    72, },
+	{    12,  -244,  3640,   920,  -308,    76, },
+	{    20,  -276,  3612,   988,  -324,    76, },
+	{    32,  -304,  3568,  1060,  -340,    80, },
+	{    40,  -332,  3532,  1132,  -356,    80, },
+	{    48,  -360,  3492,  1204,  -372,    84, },
+	{    56,  -384,  3448,  1276,  -388,    88, },
+	{    64,  -408,  3404,  1352,  -404,    88, },
+	{    72,  -428,  3348,  1428,  -416,    92, },
+	{    76,  -448,  3308,  1500,  -432,    92, },
+	{    84,  -464,  3248,  1576,  -444,    96, },
+	{    88,  -480,  3200,  1652,  -460,    96, },
+	{    92,  -492,  3140,  1728,  -472,   100, },
+	{    96,  -504,  3080,  1804,  -484,   104, },
+	{   100,  -516,  3020,  1880,  -492,   104, },
+	{   104,  -524,  2956,  1960,  -504,   104, },
+	{   104,  -532,  2892,  2036,  -512,   108, },
+	{   108,  -540,  2832,  2108,  -520,   108, },
+	{   108,  -544,  2764,  2184,  -528,   112, },
+	{   112,  -544,  2688,  2260,  -532,   112, },
+	{   112,  -548,  2624,  2336,  -540,   112, },
+	{   112,  -548,  2556,  2408,  -544,   112, },
+	{   112,  -544,  2480,  2480,  -544,   112, },
+	{   112,  -544,  2408,  2556,  -548,   112, },
+	{   112,  -540,  2336,  2624,  -548,   112, },
+	{   112,  -532,  2260,  2688,  -544,   112, },
+	{   112,  -528,  2184,  2764,  -544,   108, },
+	{   108,  -520,  2108,  2832,  -540,   108, },
+	{   108,  -512,  2036,  2892,  -532,   104, },
+	{   104,  -504,  1960,  2956,  -524,   104, },
+	{   104,  -492,  1880,  3020,  -516,   100, },
+	{   104,  -484,  1804,  3080,  -504,    96, },
+	{   100,  -472,  1728,  3140,  -492,    92, },
+	{    96,  -460,  1652,  3200,  -480,    88, },
+	{    96,  -444,  1576,  3248,  -464,    84, },
+	{    92,  -432,  1500,  3308,  -448,    76, },
+	{    92,  -416,  1428,  3348,  -428,    72, },
+	{    88,  -404,  1352,  3404,  -408,    64, },
+	{    88,  -388,  1276,  3448,  -384,    56, },
+	{    84,  -372,  1204,  3492,  -360,    48, },
+	{    80,  -356,  1132,  3532,  -332,    40, },
+	{    80,  -340,  1060,  3568,  -304,    32, },
+	{    76,  -324,   988,  3612,  -276,    20, },
+	{    76,  -308,   920,  3640,  -244,    12, },
+	{    72,  -292,   848,  3676,  -208,     0, },
+	{    72,  -276,   784,  3696,  -172,    -8, },
+	{    72,  -260,   716,  3724,  -136,   -20, },
+	{    68,  -244,   652,  3748,   -96,   -32, },
+	{    68,  -228,   588,  3768,   -52,   -48, },
+	{    68,  -208,   524,  3780,    -8,   -60, },
+	{    64,  -192,   464,  3796,    36,   -72, },
+	{    64,  -176,   404,  3808,    84,   -88, },
+	{    64,  -160,   348,  3812,   132,  -100, },
+	{    64,  -144,   292,  3816,   184,  -116, }
+};
+
+static const short
+xhsc_coeff_taps8[XSCALER_MAX_PHASES][XSCALER_TAPS_8] = {
+	{-5, 309, 1023, 1445, 1034, 317, -3, -24, },
+	{-6, 300, 1011, 1445, 1045, 326, -1, -24, },
+	{-7, 291, 1000, 1444, 1056, 336, 0, -24, },
+	{-9, 282, 988, 1444, 1067, 345, 2, -24, },
+	{-10, 274, 977, 1443, 1078, 354, 4, -24, },
+	{-11, 266, 965, 1441, 1089, 364, 6, -24, },
+	{-12, 258, 953, 1440, 1100, 373, 8, -24, },
+	{-13, 250, 942, 1438, 1110, 383, 10, -24, },
+	{-14, 242, 930, 1437, 1121, 393, 12, -24, },
+	{-15, 234, 918, 1434, 1131, 403, 14, -24, },
+	{-16, 226, 906, 1432, 1142, 413, 17, -24, },
+	{-17, 219, 894, 1430, 1152, 423, 19, -24, },
+	{-17, 211, 882, 1427, 1162, 433, 22, -24, },
+	{-18, 204, 870, 1424, 1172, 443, 24, -24, },
+	{-19, 197, 858, 1420, 1182, 454, 27, -24, },
+	{-19, 190, 846, 1417, 1191, 464, 30, -24, },
+	{-20, 183, 834, 1413, 1201, 475, 33, -24, },
+	{-20, 176, 822, 1409, 1210, 486, 36, -24, },
+	{-21, 170, 810, 1405, 1220, 497, 39, -24, },
+	{-21, 163, 798, 1401, 1229, 507, 42, -24, },
+	{-22, 157, 786, 1396, 1238, 518, 46, -24, },
+	{-22, 151, 774, 1392, 1247, 529, 49, -24, },
+	{-22, 144, 762, 1387, 1255, 540, 53, -24, },
+	{-23, 139, 750, 1382, 1264, 552, 57, -24, },
+	{-23, 133, 738, 1376, 1272, 563, 60, -24, },
+	{-23, 127, 726, 1371, 1280, 574, 64, -24, },
+	{-23, 121, 714, 1365, 1288, 586, 69, -24, },
+	{-23, 116, 703, 1359, 1296, 597, 73, -24, },
+	{-24, 111, 691, 1353, 1304, 609, 77, -24, },
+	{-24, 105, 679, 1346, 1312, 620, 81, -24, },
+	{-24, 100, 667, 1340, 1319, 632, 86, -24, },
+	{-24, 96, 655, 1333, 1326, 644, 91, -24, },
+	{-24, 91, 644, 1326, 1333, 655, 96, -24, },
+	{-24, 86, 632, 1319, 1340, 667, 100, -24, },
+	{-24, 81, 620, 1312, 1346, 679, 105, -24, },
+	{-24, 77, 609, 1304, 1353, 691, 111, -24, },
+	{-24, 73, 597, 1296, 1359, 703, 116, -23, },
+	{-24, 69, 586, 1288, 1365, 714, 121, -23, },
+	{-24, 64, 574, 1280, 1371, 726, 127, -23, },
+	{-24, 60, 563, 1272, 1376, 738, 133, -23, },
+	{-24, 57, 552, 1264, 1382, 750, 139, -23, },
+	{-24, 53, 540, 1255, 1387, 762, 144, -22, },
+	{-24, 49, 529, 1247, 1392, 774, 151, -22, },
+	{-24, 46, 518, 1238, 1396, 786, 157, -22, },
+	{-24, 42, 507, 1229, 1401, 798, 163, -21, },
+	{-24, 39, 497, 1220, 1405, 810, 170, -21, },
+	{-24, 36, 486, 1210, 1409, 822, 176, -20, },
+	{-24, 33, 475, 1201, 1413, 834, 183, -20, },
+	{-24, 30, 464, 1191, 1417, 846, 190, -19, },
+	{-24, 27, 454, 1182, 1420, 858, 197, -19, },
+	{-24, 24, 443, 1172, 1424, 870, 204, -18, },
+	{-24, 22, 433, 1162, 1427, 882, 211, -17, },
+	{-24, 19, 423, 1152, 1430, 894, 219, -17, },
+	{-24, 17, 413, 1142, 1432, 906, 226, -16, },
+	{-24, 14, 403, 1131, 1434, 918, 234, -15, },
+	{-24, 12, 393, 1121, 1437, 930, 242, -14, },
+	{-24, 10, 383, 1110, 1438, 942, 250, -13, },
+	{-24, 8, 373, 1100, 1440, 953, 258, -12, },
+	{-24, 6, 364, 1089, 1441, 965, 266, -11, },
+	{-24, 4, 354, 1078, 1443, 977, 274, -10, },
+	{-24, 2, 345, 1067, 1444, 988, 282, -9, },
+	{-24, 0, 336, 1056, 1444, 1000, 291, -7, },
+	{-24, -1, 326, 1045, 1445, 1011, 300, -6, },
+	{-24, -3, 317, 1034, 1445, 1023, 309, -5, },
+};
+
+static const short
+xhsc_coeff_taps10[XSCALER_MAX_PHASES][XSCALER_TAPS_10] = {
+	{59, 224, 507, 790, 911, 793, 512, 227, 61, 13, },
+	{58, 220, 502, 786, 911, 797, 516, 231, 62, 13, },
+	{56, 216, 497, 783, 911, 800, 521, 235, 64, 13, },
+	{55, 213, 492, 779, 910, 804, 526, 238, 65, 13, },
+	{54, 209, 487, 775, 910, 807, 531, 242, 67, 14, },
+	{52, 206, 482, 772, 910, 810, 536, 246, 69, 14, },
+	{51, 202, 477, 768, 909, 813, 541, 250, 70, 14, },
+	{50, 199, 473, 764, 909, 817, 545, 254, 72, 14, },
+	{48, 195, 468, 760, 908, 820, 550, 258, 74, 15, },
+	{47, 192, 463, 756, 908, 823, 555, 262, 76, 15, },
+	{46, 188, 458, 752, 907, 826, 560, 266, 78, 15, },
+	{45, 185, 453, 748, 906, 829, 565, 270, 79, 16, },
+	{44, 182, 448, 744, 906, 832, 569, 274, 81, 16, },
+	{42, 179, 444, 740, 905, 835, 574, 278, 83, 16, },
+	{41, 175, 439, 736, 904, 837, 579, 282, 85, 17, },
+	{40, 172, 434, 732, 903, 840, 584, 286, 87, 17, },
+	{39, 169, 429, 728, 902, 843, 589, 290, 89, 18, },
+	{38, 166, 425, 724, 901, 846, 593, 294, 91, 18, },
+	{37, 163, 420, 720, 900, 848, 598, 298, 93, 18, },
+	{36, 160, 415, 716, 899, 851, 603, 302, 95, 19, },
+	{35, 157, 410, 711, 897, 854, 608, 307, 98, 19, },
+	{34, 154, 406, 707, 896, 856, 612, 311, 100, 20, },
+	{33, 151, 401, 703, 895, 859, 617, 315, 102, 20, },
+	{33, 148, 396, 698, 893, 861, 622, 320, 104, 21, },
+	{32, 145, 392, 694, 892, 863, 626, 324, 107, 21, },
+	{31, 142, 387, 690, 890, 866, 631, 328, 109, 22, },
+	{30, 140, 382, 685, 889, 868, 636, 333, 111, 23, },
+	{29, 137, 378, 681, 887, 870, 640, 337, 114, 23, },
+	{28, 134, 373, 677, 886, 872, 645, 342, 116, 24, },
+	{28, 131, 369, 672, 884, 874, 649, 346, 119, 24, },
+	{27, 129, 364, 668, 882, 876, 654, 350, 121, 25, },
+	{26, 126, 359, 663, 880, 878, 659, 355, 124, 26, },
+	{26, 124, 355, 659, 878, 880, 663, 359, 126, 26, },
+	{25, 121, 350, 654, 876, 882, 668, 364, 129, 27, },
+	{24, 119, 346, 649, 874, 884, 672, 369, 131, 28, },
+	{24, 116, 342, 645, 872, 886, 677, 373, 134, 28, },
+	{23, 114, 337, 640, 870, 887, 681, 378, 137, 29, },
+	{23, 111, 333, 636, 868, 889, 685, 382, 140, 30, },
+	{22, 109, 328, 631, 866, 890, 690, 387, 142, 31, },
+	{21, 107, 324, 626, 863, 892, 694, 392, 145, 32, },
+	{21, 104, 320, 622, 861, 893, 698, 396, 148, 33, },
+	{20, 102, 315, 617, 859, 895, 703, 401, 151, 33, },
+	{20, 100, 311, 612, 856, 896, 707, 406, 154, 34, },
+	{19, 98, 307, 608, 854, 897, 711, 410, 157, 35, },
+	{19, 95, 302, 603, 851, 899, 716, 415, 160, 36, },
+	{18, 93, 298, 598, 848, 900, 720, 420, 163, 37, },
+	{18, 91, 294, 593, 846, 901, 724, 425, 166, 38, },
+	{18, 89, 290, 589, 843, 902, 728, 429, 169, 39, },
+	{17, 87, 286, 584, 840, 903, 732, 434, 172, 40, },
+	{17, 85, 282, 579, 837, 904, 736, 439, 175, 41, },
+	{16, 83, 278, 574, 835, 905, 740, 444, 179, 42, },
+	{16, 81, 274, 569, 832, 906, 744, 448, 182, 44, },
+	{16, 79, 270, 565, 829, 906, 748, 453, 185, 45, },
+	{15, 78, 266, 560, 826, 907, 752, 458, 188, 46, },
+	{15, 76, 262, 555, 823, 908, 756, 463, 192, 47, },
+	{15, 74, 258, 550, 820, 908, 760, 468, 195, 48, },
+	{14, 72, 254, 545, 817, 909, 764, 473, 199, 50, },
+	{14, 70, 250, 541, 813, 909, 768, 477, 202, 51, },
+	{14, 69, 246, 536, 810, 910, 772, 482, 206, 52, },
+	{14, 67, 242, 531, 807, 910, 775, 487, 209, 54, },
+	{13, 65, 238, 526, 804, 910, 779, 492, 213, 55, },
+	{13, 64, 235, 521, 800, 911, 783, 497, 216, 56, },
+	{13, 62, 231, 516, 797, 911, 786, 502, 220, 58, },
+	{13, 61, 227, 512, 793, 911, 790, 507, 224, 59, },
+};
+
+static const short
+xhsc_coeff_taps12[XSCALER_MAX_PHASES][XSCALER_TAPS_12] = {
+	{48, 143, 307, 504, 667, 730, 669, 507, 310, 145, 49, 18, },
+	{47, 141, 304, 501, 665, 730, 670, 510, 313, 147, 50, 18, },
+	{46, 138, 301, 498, 663, 730, 672, 513, 316, 149, 51, 18, },
+	{45, 136, 298, 495, 661, 730, 674, 516, 319, 151, 52, 18, },
+	{44, 134, 295, 492, 659, 730, 676, 519, 322, 153, 53, 18, },
+	{44, 132, 292, 489, 657, 730, 677, 522, 325, 155, 54, 18, },
+	{43, 130, 289, 486, 655, 729, 679, 525, 328, 157, 55, 19, },
+	{42, 129, 287, 483, 653, 729, 681, 528, 331, 160, 56, 19, },
+	{41, 127, 284, 480, 651, 729, 683, 531, 334, 162, 57, 19, },
+	{40, 125, 281, 477, 648, 729, 684, 534, 337, 164, 58, 19, },
+	{40, 123, 278, 474, 646, 728, 686, 537, 340, 166, 59, 20, },
+	{39, 121, 275, 471, 644, 728, 687, 539, 343, 169, 60, 20, },
+	{38, 119, 272, 468, 642, 727, 689, 542, 346, 171, 61, 20, },
+	{37, 117, 269, 465, 640, 727, 690, 545, 349, 173, 62, 20, },
+	{37, 115, 266, 461, 638, 727, 692, 548, 353, 175, 63, 21, },
+	{36, 114, 264, 458, 635, 726, 693, 551, 356, 178, 65, 21, },
+	{35, 112, 261, 455, 633, 726, 695, 554, 359, 180, 66, 21, },
+	{35, 110, 258, 452, 631, 725, 696, 556, 362, 183, 67, 21, },
+	{34, 108, 255, 449, 628, 724, 698, 559, 365, 185, 68, 22, },
+	{33, 107, 252, 446, 626, 724, 699, 562, 368, 187, 69, 22, },
+	{33, 105, 250, 443, 624, 723, 700, 565, 371, 190, 71, 22, },
+	{32, 103, 247, 440, 621, 723, 702, 567, 374, 192, 72, 23, },
+	{32, 101, 244, 437, 619, 722, 703, 570, 377, 195, 73, 23, },
+	{31, 100, 241, 433, 617, 721, 704, 573, 380, 197, 75, 23, },
+	{31, 98, 239, 430, 614, 720, 705, 576, 383, 200, 76, 24, },
+	{30, 97, 236, 427, 612, 720, 707, 578, 387, 202, 77, 24, },
+	{29, 95, 233, 424, 609, 719, 708, 581, 390, 205, 79, 24, },
+	{29, 93, 231, 421, 607, 718, 709, 584, 393, 207, 80, 25, },
+	{28, 92, 228, 418, 604, 717, 710, 586, 396, 210, 81, 25, },
+	{28, 90, 225, 415, 602, 716, 711, 589, 399, 212, 83, 26, },
+	{27, 89, 223, 412, 599, 715, 712, 591, 402, 215, 84, 26, },
+	{27, 87, 220, 408, 597, 714, 713, 594, 405, 217, 86, 27, },
+	{27, 86, 217, 405, 594, 713, 714, 597, 408, 220, 87, 27, },
+	{26, 84, 215, 402, 591, 712, 715, 599, 412, 223, 89, 27, },
+	{26, 83, 212, 399, 589, 711, 716, 602, 415, 225, 90, 28, },
+	{25, 81, 210, 396, 586, 710, 717, 604, 418, 228, 92, 28, },
+	{25, 80, 207, 393, 584, 709, 718, 607, 421, 231, 93, 29, },
+	{24, 79, 205, 390, 581, 708, 719, 609, 424, 233, 95, 29, },
+	{24, 77, 202, 387, 578, 707, 720, 612, 427, 236, 97, 30, },
+	{24, 76, 200, 383, 576, 705, 720, 614, 430, 239, 98, 31, },
+	{23, 75, 197, 380, 573, 704, 721, 617, 433, 241, 100, 31, },
+	{23, 73, 195, 377, 570, 703, 722, 619, 437, 244, 101, 32, },
+	{23, 72, 192, 374, 567, 702, 723, 621, 440, 247, 103, 32, },
+	{22, 71, 190, 371, 565, 700, 723, 624, 443, 250, 105, 33, },
+	{22, 69, 187, 368, 562, 699, 724, 626, 446, 252, 107, 33, },
+	{22, 68, 185, 365, 559, 698, 724, 628, 449, 255, 108, 34, },
+	{21, 67, 183, 362, 556, 696, 725, 631, 452, 258, 110, 35, },
+	{21, 66, 180, 359, 554, 695, 726, 633, 455, 261, 112, 35, },
+	{21, 65, 178, 356, 551, 693, 726, 635, 458, 264, 114, 36, },
+	{21, 63, 175, 353, 548, 692, 727, 638, 461, 266, 115, 37, },
+	{20, 62, 173, 349, 545, 690, 727, 640, 465, 269, 117, 37, },
+	{20, 61, 171, 346, 542, 689, 727, 642, 468, 272, 119, 38, },
+	{20, 60, 169, 343, 539, 687, 728, 644, 471, 275, 121, 39, },
+	{20, 59, 166, 340, 537, 686, 728, 646, 474, 278, 123, 40, },
+	{19, 58, 164, 337, 534, 684, 729, 648, 477, 281, 125, 40, },
+	{19, 57, 162, 334, 531, 683, 729, 651, 480, 284, 127, 41, },
+	{19, 56, 160, 331, 528, 681, 729, 653, 483, 287, 129, 42, },
+	{19, 55, 157, 328, 525, 679, 729, 655, 486, 289, 130, 43, },
+	{18, 54, 155, 325, 522, 677, 730, 657, 489, 292, 132, 44, },
+	{18, 53, 153, 322, 519, 676, 730, 659, 492, 295, 134, 44, },
+	{18, 52, 151, 319, 516, 674, 730, 661, 495, 298, 136, 45, },
+	{18, 51, 149, 316, 513, 672, 730, 663, 498, 301, 138, 46, },
+	{18, 50, 147, 313, 510, 670, 730, 665, 501, 304, 141, 47, },
+	{18, 49, 145, 310, 507, 669, 730, 667, 504, 307, 143, 48, },
+};
+
+/* V-scaler coefficients for 6, 8, 10 and 12 tap filters */
+static const short
+xvsc_coeff_taps6[XSCALER_MAX_PHASES][XSCALER_TAPS_6] = {
+	{-132, 236, 3824, 236, -132, 64, },
+	{-116, 184, 3816, 292, -144, 64, },
+	{-100, 132, 3812, 348, -160, 64, },
+	{-88, 84, 3808, 404, -176, 64, },
+	{-72, 36, 3796, 464, -192, 64, },
+	{-60, -8, 3780, 524, -208, 68, },
+	{-48, -52, 3768, 588, -228, 68, },
+	{-32, -96, 3748, 652, -244, 68, },
+	{-20, -136, 3724, 716, -260, 72, },
+	{-8, -172, 3696, 784, -276, 72, },
+	{0, -208, 3676, 848, -292, 72, },
+	{12, -244, 3640, 920, -308, 76, },
+	{20, -276, 3612, 988, -324, 76, },
+	{32, -304, 3568, 1060, -340, 80, },
+	{40, -332, 3532, 1132, -356, 80, },
+	{48, -360, 3492, 1204, -372, 84, },
+	{56, -384, 3448, 1276, -388, 88, },
+	{64, -408, 3404, 1352, -404, 88, },
+	{72, -428, 3348, 1428, -416, 92, },
+	{76, -448, 3308, 1500, -432, 92, },
+	{84, -464, 3248, 1576, -444, 96, },
+	{88, -480, 3200, 1652, -460, 96, },
+	{92, -492, 3140, 1728, -472, 100, },
+	{96, -504, 3080, 1804, -484, 104, },
+	{100, -516, 3020, 1880, -492, 104, },
+	{104, -524, 2956, 1960, -504, 104, },
+	{104, -532, 2892, 2036, -512, 108, },
+	{108, -540, 2832, 2108, -520, 108, },
+	{108, -544, 2764, 2184, -528, 112, },
+	{112, -544, 2688, 2260, -532, 112, },
+	{112, -548, 2624, 2336, -540, 112, },
+	{112, -548, 2556, 2408, -544, 112, },
+	{112, -544, 2480, 2480, -544, 112, },
+	{112, -544, 2408, 2556, -548, 112, },
+	{112, -540, 2336, 2624, -548, 112, },
+	{112, -532, 2260, 2688, -544, 112, },
+	{112, -528, 2184, 2764, -544, 108, },
+	{108, -520, 2108, 2832, -540, 108, },
+	{108, -512, 2036, 2892, -532, 104, },
+	{104, -504, 1960, 2956, -524, 104, },
+	{104, -492, 1880, 3020, -516, 100, },
+	{104, -484, 1804, 3080, -504, 96, },
+	{100, -472, 1728, 3140, -492, 92, },
+	{ 96, -460, 1652, 3200, -480, 88, },
+	{ 96, -444, 1576, 3248, -464, 84, },
+	{ 92, -432, 1500, 3308, -448, 76, },
+	{ 92, -416, 1428, 3348, -428, 72, },
+	{ 88, -404, 1352, 3404, -408, 64, },
+	{ 88, -388, 1276, 3448, -384, 56, },
+	{ 84, -372, 1204, 3492, -360, 48, },
+	{ 80, -356, 1132, 3532, -332, 40, },
+	{ 80, -340, 1060, 3568, -304, 32, },
+	{ 76, -324, 988, 3612, -276, 20, },
+	{ 76, -308, 920, 3640, -244, 12, },
+	{ 72, -292, 848, 3676, -208, 0, },
+	{ 72, -276, 784, 3696, -172, -8, },
+	{ 72, -260, 716, 3724, -136, -20, },
+	{ 68, -244, 652, 3748, -96, -32, },
+	{ 68, -228, 588, 3768, -52, -48, },
+	{ 68, -208, 524, 3780, -8, -60, },
+	{ 64, -192, 464, 3796, 36, -72, },
+	{ 64, -176, 404, 3808, 84, -88, },
+	{ 64, -160, 348, 3812, 132, -100, },
+	{ 64, -144, 292, 3816, 184, -116, }
+};
+
+static const short
+xvsc_coeff_taps8[XSCALER_MAX_PHASES][XSCALER_TAPS_8] = {
+	{-5, 309, 1023, 1445, 1034, 317, -3, -24, },
+	{-6, 300, 1011, 1445, 1045, 326, -1, -24, },
+	{-7, 291, 1000, 1444, 1056, 336, 0, -24, },
+	{-9, 282, 988, 1444, 1067, 345, 2, -24, },
+	{-10, 274, 977, 1443, 1078, 354, 4, -24, },
+	{-11, 266, 965, 1441, 1089, 364, 6, -24, },
+	{-12, 258, 953, 1440, 1100, 373, 8, -24, },
+	{-13, 250, 942, 1438, 1110, 383, 10, -24, },
+	{-14, 242, 930, 1437, 1121, 393, 12, -24, },
+	{-15, 234, 918, 1434, 1131, 403, 14, -24, },
+	{-16, 226, 906, 1432, 1142, 413, 17, -24, },
+	{-17, 219, 894, 1430, 1152, 423, 19, -24, },
+	{-17, 211, 882, 1427, 1162, 433, 22, -24, },
+	{-18, 204, 870, 1424, 1172, 443, 24, -24, },
+	{-19, 197, 858, 1420, 1182, 454, 27, -24, },
+	{-19, 190, 846, 1417, 1191, 464, 30, -24, },
+	{-20, 183, 834, 1413, 1201, 475, 33, -24, },
+	{-20, 176, 822, 1409, 1210, 486, 36, -24, },
+	{-21, 170, 810, 1405, 1220, 497, 39, -24, },
+	{-21, 163, 798, 1401, 1229, 507, 42, -24, },
+	{-22, 157, 786, 1396, 1238, 518, 46, -24, },
+	{-22, 151, 774, 1392, 1247, 529, 49, -24, },
+	{-22, 144, 762, 1387, 1255, 540, 53, -24, },
+	{-23, 139, 750, 1382, 1264, 552, 57, -24, },
+	{-23, 133, 738, 1376, 1272, 563, 60, -24, },
+	{-23, 127, 726, 1371, 1280, 574, 64, -24, },
+	{-23, 121, 714, 1365, 1288, 586, 69, -24, },
+	{-23, 116, 703, 1359, 1296, 597, 73, -24, },
+	{-24, 111, 691, 1353, 1304, 609, 77, -24, },
+	{-24, 105, 679, 1346, 1312, 620, 81, -24, },
+	{-24, 100, 667, 1340, 1319, 632, 86, -24, },
+	{-24, 96, 655, 1333, 1326, 644, 91, -24, },
+	{-24, 91, 644, 1326, 1333, 655, 96, -24, },
+	{-24, 86, 632, 1319, 1340, 667, 100, -24, },
+	{-24, 81, 620, 1312, 1346, 679, 105, -24, },
+	{-24, 77, 609, 1304, 1353, 691, 111, -24, },
+	{-24, 73, 597, 1296, 1359, 703, 116, -23, },
+	{-24, 69, 586, 1288, 1365, 714, 121, -23, },
+	{-24, 64, 574, 1280, 1371, 726, 127, -23, },
+	{-24, 60, 563, 1272, 1376, 738, 133, -23, },
+	{-24, 57, 552, 1264, 1382, 750, 139, -23, },
+	{-24, 53, 540, 1255, 1387, 762, 144, -22, },
+	{-24, 49, 529, 1247, 1392, 774, 151, -22, },
+	{-24, 46, 518, 1238, 1396, 786, 157, -22, },
+	{-24, 42, 507, 1229, 1401, 798, 163, -21, },
+	{-24, 39, 497, 1220, 1405, 810, 170, -21, },
+	{-24, 36, 486, 1210, 1409, 822, 176, -20, },
+	{-24, 33, 475, 1201, 1413, 834, 183, -20, },
+	{-24, 30, 464, 1191, 1417, 846, 190, -19, },
+	{-24, 27, 454, 1182, 1420, 858, 197, -19, },
+	{-24, 24, 443, 1172, 1424, 870, 204, -18, },
+	{-24, 22, 433, 1162, 1427, 882, 211, -17, },
+	{-24, 19, 423, 1152, 1430, 894, 219, -17, },
+	{-24, 17, 413, 1142, 1432, 906, 226, -16, },
+	{-24, 14, 403, 1131, 1434, 918, 234, -15, },
+	{-24, 12, 393, 1121, 1437, 930, 242, -14, },
+	{-24, 10, 383, 1110, 1438, 942, 250, -13, },
+	{-24, 8, 373, 1100, 1440, 953, 258, -12, },
+	{-24, 6, 364, 1089, 1441, 965, 266, -11, },
+	{-24, 4, 354, 1078, 1443, 977, 274, -10, },
+	{-24, 2, 345, 1067, 1444, 988, 282, -9, },
+	{-24, 0, 336, 1056, 1444, 1000, 291, -7, },
+	{-24, -1, 326, 1045, 1445, 1011, 300, -6, },
+	{-24, -3, 317, 1034, 1445, 1023, 309, -5, },
+};
+
+static const short
+xvsc_coeff_taps10[XSCALER_MAX_PHASES][XSCALER_TAPS_10] = {
+	{59, 224, 507, 790, 911, 793, 512, 227, 61, 13, },
+	{58, 220, 502, 786, 911, 797, 516, 231, 62, 13, },
+	{56, 216, 497, 783, 911, 800, 521, 235, 64, 13, },
+	{55, 213, 492, 779, 910, 804, 526, 238, 65, 13, },
+	{54, 209, 487, 775, 910, 807, 531, 242, 67, 14, },
+	{52, 206, 482, 772, 910, 810, 536, 246, 69, 14, },
+	{51, 202, 477, 768, 909, 813, 541, 250, 70, 14, },
+	{50, 199, 473, 764, 909, 817, 545, 254, 72, 14, },
+	{48, 195, 468, 760, 908, 820, 550, 258, 74, 15, },
+	{47, 192, 463, 756, 908, 823, 555, 262, 76, 15, },
+	{46, 188, 458, 752, 907, 826, 560, 266, 78, 15, },
+	{45, 185, 453, 748, 906, 829, 565, 270, 79, 16, },
+	{44, 182, 448, 744, 906, 832, 569, 274, 81, 16, },
+	{42, 179, 444, 740, 905, 835, 574, 278, 83, 16, },
+	{41, 175, 439, 736, 904, 837, 579, 282, 85, 17, },
+	{40, 172, 434, 732, 903, 840, 584, 286, 87, 17, },
+	{39, 169, 429, 728, 902, 843, 589, 290, 89, 18, },
+	{38, 166, 425, 724, 901, 846, 593, 294, 91, 18, },
+	{37, 163, 420, 720, 900, 848, 598, 298, 93, 18, },
+	{36, 160, 415, 716, 899, 851, 603, 302, 95, 19, },
+	{35, 157, 410, 711, 897, 854, 608, 307, 98, 19, },
+	{34, 154, 406, 707, 896, 856, 612, 311, 100, 20, },
+	{33, 151, 401, 703, 895, 859, 617, 315, 102, 20, },
+	{33, 148, 396, 698, 893, 861, 622, 320, 104, 21, },
+	{32, 145, 392, 694, 892, 863, 626, 324, 107, 21, },
+	{31, 142, 387, 690, 890, 866, 631, 328, 109, 22, },
+	{30, 140, 382, 685, 889, 868, 636, 333, 111, 23, },
+	{29, 137, 378, 681, 887, 870, 640, 337, 114, 23, },
+	{28, 134, 373, 677, 886, 872, 645, 342, 116, 24, },
+	{28, 131, 369, 672, 884, 874, 649, 346, 119, 24, },
+	{27, 129, 364, 668, 882, 876, 654, 350, 121, 25, },
+	{26, 126, 359, 663, 880, 878, 659, 355, 124, 26, },
+	{26, 124, 355, 659, 878, 880, 663, 359, 126, 26, },
+	{25, 121, 350, 654, 876, 882, 668, 364, 129, 27, },
+	{24, 119, 346, 649, 874, 884, 672, 369, 131, 28, },
+	{24, 116, 342, 645, 872, 886, 677, 373, 134, 28, },
+	{23, 114, 337, 640, 870, 887, 681, 378, 137, 29, },
+	{23, 111, 333, 636, 868, 889, 685, 382, 140, 30, },
+	{22, 109, 328, 631, 866, 890, 690, 387, 142, 31, },
+	{21, 107, 324, 626, 863, 892, 694, 392, 145, 32, },
+	{21, 104, 320, 622, 861, 893, 698, 396, 148, 33, },
+	{20, 102, 315, 617, 859, 895, 703, 401, 151, 33, },
+	{20, 100, 311, 612, 856, 896, 707, 406, 154, 34, },
+	{19, 98, 307, 608, 854, 897, 711, 410, 157, 35, },
+	{19, 95, 302, 603, 851, 899, 716, 415, 160, 36, },
+	{18, 93, 298, 598, 848, 900, 720, 420, 163, 37, },
+	{18, 91, 294, 593, 846, 901, 724, 425, 166, 38, },
+	{18, 89, 290, 589, 843, 902, 728, 429, 169, 39, },
+	{17, 87, 286, 584, 840, 903, 732, 434, 172, 40, },
+	{17, 85, 282, 579, 837, 904, 736, 439, 175, 41, },
+	{16, 83, 278, 574, 835, 905, 740, 444, 179, 42, },
+	{16, 81, 274, 569, 832, 906, 744, 448, 182, 44, },
+	{16, 79, 270, 565, 829, 906, 748, 453, 185, 45, },
+	{15, 78, 266, 560, 826, 907, 752, 458, 188, 46, },
+	{15, 76, 262, 555, 823, 908, 756, 463, 192, 47, },
+	{15, 74, 258, 550, 820, 908, 760, 468, 195, 48, },
+	{14, 72, 254, 545, 817, 909, 764, 473, 199, 50, },
+	{14, 70, 250, 541, 813, 909, 768, 477, 202, 51, },
+	{14, 69, 246, 536, 810, 910, 772, 482, 206, 52, },
+	{14, 67, 242, 531, 807, 910, 775, 487, 209, 54, },
+	{13, 65, 238, 526, 804, 910, 779, 492, 213, 55, },
+	{13, 64, 235, 521, 800, 911, 783, 497, 216, 56, },
+	{13, 62, 231, 516, 797, 911, 786, 502, 220, 58, },
+	{13, 61, 227, 512, 793, 911, 790, 507, 224, 59, },
+};
+
+static const short
+xvsc_coeff_taps12[XSCALER_MAX_PHASES][XSCALER_TAPS_12] = {
+	{48, 143, 307, 504, 667, 730, 669, 507, 310, 145, 49, 18, },
+	{47, 141, 304, 501, 665, 730, 670, 510, 313, 147, 50, 18, },
+	{46, 138, 301, 498, 663, 730, 672, 513, 316, 149, 51, 18, },
+	{45, 136, 298, 495, 661, 730, 674, 516, 319, 151, 52, 18, },
+	{44, 134, 295, 492, 659, 730, 676, 519, 322, 153, 53, 18, },
+	{44, 132, 292, 489, 657, 730, 677, 522, 325, 155, 54, 18, },
+	{43, 130, 289, 486, 655, 729, 679, 525, 328, 157, 55, 19, },
+	{42, 129, 287, 483, 653, 729, 681, 528, 331, 160, 56, 19, },
+	{41, 127, 284, 480, 651, 729, 683, 531, 334, 162, 57, 19, },
+	{40, 125, 281, 477, 648, 729, 684, 534, 337, 164, 58, 19, },
+	{40, 123, 278, 474, 646, 728, 686, 537, 340, 166, 59, 20, },
+	{39, 121, 275, 471, 644, 728, 687, 539, 343, 169, 60, 20, },
+	{38, 119, 272, 468, 642, 727, 689, 542, 346, 171, 61, 20, },
+	{37, 117, 269, 465, 640, 727, 690, 545, 349, 173, 62, 20, },
+	{37, 115, 266, 461, 638, 727, 692, 548, 353, 175, 63, 21, },
+	{36, 114, 264, 458, 635, 726, 693, 551, 356, 178, 65, 21, },
+	{35, 112, 261, 455, 633, 726, 695, 554, 359, 180, 66, 21, },
+	{35, 110, 258, 452, 631, 725, 696, 556, 362, 183, 67, 21, },
+	{34, 108, 255, 449, 628, 724, 698, 559, 365, 185, 68, 22, },
+	{33, 107, 252, 446, 626, 724, 699, 562, 368, 187, 69, 22, },
+	{33, 105, 250, 443, 624, 723, 700, 565, 371, 190, 71, 22, },
+	{32, 103, 247, 440, 621, 723, 702, 567, 374, 192, 72, 23, },
+	{32, 101, 244, 437, 619, 722, 703, 570, 377, 195, 73, 23, },
+	{31, 100, 241, 433, 617, 721, 704, 573, 380, 197, 75, 23, },
+	{31, 98, 239, 430, 614, 720, 705, 576, 383, 200, 76, 24, },
+	{30, 97, 236, 427, 612, 720, 707, 578, 387, 202, 77, 24, },
+	{29, 95, 233, 424, 609, 719, 708, 581, 390, 205, 79, 24, },
+	{29, 93, 231, 421, 607, 718, 709, 584, 393, 207, 80, 25, },
+	{28, 92, 228, 418, 604, 717, 710, 586, 396, 210, 81, 25, },
+	{28, 90, 225, 415, 602, 716, 711, 589, 399, 212, 83, 26, },
+	{27, 89, 223, 412, 599, 715, 712, 591, 402, 215, 84, 26, },
+	{27, 87, 220, 408, 597, 714, 713, 594, 405, 217, 86, 27, },
+	{27, 86, 217, 405, 594, 713, 714, 597, 408, 220, 87, 27, },
+	{26, 84, 215, 402, 591, 712, 715, 599, 412, 223, 89, 27, },
+	{26, 83, 212, 399, 589, 711, 716, 602, 415, 225, 90, 28, },
+	{25, 81, 210, 396, 586, 710, 717, 604, 418, 228, 92, 28, },
+	{25, 80, 207, 393, 584, 709, 718, 607, 421, 231, 93, 29, },
+	{24, 79, 205, 390, 581, 708, 719, 609, 424, 233, 95, 29, },
+	{24, 77, 202, 387, 578, 707, 720, 612, 427, 236, 97, 30, },
+	{24, 76, 200, 383, 576, 705, 720, 614, 430, 239, 98, 31, },
+	{23, 75, 197, 380, 573, 704, 721, 617, 433, 241, 100, 31, },
+	{23, 73, 195, 377, 570, 703, 722, 619, 437, 244, 101, 32, },
+	{23, 72, 192, 374, 567, 702, 723, 621, 440, 247, 103, 32, },
+	{22, 71, 190, 371, 565, 700, 723, 624, 443, 250, 105, 33, },
+	{22, 69, 187, 368, 562, 699, 724, 626, 446, 252, 107, 33, },
+	{22, 68, 185, 365, 559, 698, 724, 628, 449, 255, 108, 34, },
+	{21, 67, 183, 362, 556, 696, 725, 631, 452, 258, 110, 35, },
+	{21, 66, 180, 359, 554, 695, 726, 633, 455, 261, 112, 35, },
+	{21, 65, 178, 356, 551, 693, 726, 635, 458, 264, 114, 36, },
+	{21, 63, 175, 353, 548, 692, 727, 638, 461, 266, 115, 37, },
+	{20, 62, 173, 349, 545, 690, 727, 640, 465, 269, 117, 37, },
+	{20, 61, 171, 346, 542, 689, 727, 642, 468, 272, 119, 38, },
+	{20, 60, 169, 343, 539, 687, 728, 644, 471, 275, 121, 39, },
+	{20, 59, 166, 340, 537, 686, 728, 646, 474, 278, 123, 40, },
+	{19, 58, 164, 337, 534, 684, 729, 648, 477, 281, 125, 40, },
+	{19, 57, 162, 334, 531, 683, 729, 651, 480, 284, 127, 41, },
+	{19, 56, 160, 331, 528, 681, 729, 653, 483, 287, 129, 42, },
+	{19, 55, 157, 328, 525, 679, 729, 655, 486, 289, 130, 43, },
+	{18, 54, 155, 325, 522, 677, 730, 657, 489, 292, 132, 44, },
+	{18, 53, 153, 322, 519, 676, 730, 659, 492, 295, 134, 44, },
+	{18, 52, 151, 319, 516, 674, 730, 661, 495, 298, 136, 45, },
+	{18, 51, 149, 316, 513, 672, 730, 663, 498, 301, 138, 46, },
+	{18, 50, 147, 313, 510, 670, 730, 665, 501, 304, 141, 47, },
+	{18, 49, 145, 310, 507, 669, 730, 667, 504, 307, 143, 48, },
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-multi-scaler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-multi-scaler.c
@@ -0,0 +1,2483 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Memory-to-Memory Video Multi-Scaler IP
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Author: Suresh Gupta <suresh.gupta@xilinx.com>
+ *
+ * Based on the virtual v4l2-mem2mem example device
+ *
+ * This driver adds support to control the Xilinx Video Multi
+ * Scaler Controller
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-mem2mem.h>
+#include <media/videobuf2-dma-contig.h>
+
+#include "xilinx-multi-scaler-coeff.h"
+
+/* 0x0000 : Control signals */
+#define XM2MSC_AP_CTRL			0x0000
+#define XM2MSC_AP_CTRL_START		BIT(0)
+#define XM2MSC_AP_CTRL_DONE		BIT(1)
+#define XM2MSC_AP_CTRL_IDEL		BIT(2)
+#define XM2MSC_AP_CTRL_READY		BIT(3)
+#define XM2MSC_AP_CTRL_AUTO_RESTART	BIT(7)
+
+/* 0x0004 : Global Interrupt Enable Register */
+#define XM2MSC_GIE			0x0004
+#define XM2MSC_GIE_EN			BIT(0)
+
+/* 0x0008 : IP Interrupt Enable Register (Read/Write) */
+#define XM2MSC_IER			0x0008
+#define XM2MSC_ISR			0x000c
+#define XM2MSC_ISR_DONE			BIT(0)
+#define XM2MSC_ISR_READY		BIT(1)
+
+#define XM2MSC_NUM_OUTS			0x0010
+
+#define XM2MSC_WIDTHIN			0x000
+#define XM2MSC_WIDTHOUT			0x008
+#define XM2MSC_HEIGHTIN			0x010
+#define XM2MSC_HEIGHTOUT		0x018
+#define XM2MSC_LINERATE			0x020
+#define XM2MSC_PIXELRATE		0x028
+#define XM2MSC_INPIXELFMT		0x030
+#define XM2MSC_OUTPIXELFMT		0x038
+#define XM2MSC_INSTRIDE			0x050
+#define XM2MSC_OUTSTRIDE		0x058
+#define XM2MSC_SRCIMGBUF0		0x060
+#define XM2MSC_SRCIMGBUF1		0x070
+#define XM2MSC_DSTIMGBUF0		0x090
+#define XM2MSC_DSTIMGBUF1		0x0100
+
+#define XM2MVSC_VFLTCOEFF_L	0x2000
+#define XM2MVSC_VFLTCOEFF(x)	(XM2MVSC_VFLTCOEFF_L + 0x2000 * (x))
+#define XM2MVSC_HFLTCOEFF_L	0x2800
+#define XM2MVSC_HFLTCOEFF(x)	(XM2MVSC_HFLTCOEFF_L + 0x2000 * (x))
+
+#define XM2MSC_CHAN_REGS_START(x)	(0x100 + 0x200 * (x))
+
+/*
+ * IP has reserved area between XM2MSC_DSTIMGBUF0 and
+ * XM2MSC_DSTIMGBUF1 registers of channel 4
+ */
+#define XM2MSC_RESERVED_AREA		0x600
+
+/* GPIO RESET MACROS */
+#define XM2MSC_RESET_ASSERT	(0x1)
+#define XM2MSC_RESET_DEASSERT	(0x0)
+
+#define XM2MSC_MIN_CHAN		1
+#define XM2MSC_MAX_CHAN		8
+
+#define XM2MSC_MAX_WIDTH	(8192)
+#define XM2MSC_MAX_HEIGHT	(4320)
+#define XM2MSC_MIN_WIDTH	(64)
+#define XM2MSC_MIN_HEIGHT	(64)
+#define XM2MSC_STEP_PRECISION	(65536)
+/* Mask definitions for Low 16 bits in a 32 bit number */
+#define XM2MSC_MASK_LOW_16BITS	GENMASK(15, 0)
+#define XM2MSC_BITSHIFT_16	(16)
+
+#define XM2MSC_DRIVER_NAME	"xm2msc"
+
+#define CHAN_ATTACHED		BIT(0)
+#define CHAN_OPENED		BIT(1)
+
+#define XM2MSC_CHAN_OUT		0
+#define XM2MSC_CHAN_CAP		1
+
+#define NUM_STREAM(_x)			\
+	({ typeof(_x) (x) = (_x);	\
+	min(ffz(x->out_streamed_chan),	\
+	    ffz(x->cap_streamed_chan)); })
+
+#define XM2MSC_ALIGN_MUL	8
+
+/*
+ * These are temporary variables. Once the stride and height
+ * alignment support added to plugin, these variables will
+ * be remove.
+ */
+static unsigned int output_stride_align[XM2MSC_MAX_CHAN] = {
+					1, 1, 1, 1, 1, 1, 1, 1 };
+module_param_array(output_stride_align, uint, NULL, 0644);
+MODULE_PARM_DESC(output_stride_align,
+		 "Per Cahnnel stride alignment requied at output.");
+
+static unsigned int capture_stride_align[XM2MSC_MAX_CHAN] = {
+					1, 1, 1, 1, 1, 1, 1, 1 };
+module_param_array(capture_stride_align, uint, NULL, 0644);
+MODULE_PARM_DESC(capture_stride_align,
+		 "Per channel stride alignment requied at capture.");
+
+static unsigned int output_height_align[XM2MSC_MAX_CHAN] = {
+					1, 1, 1, 1, 1, 1, 1, 1 };
+module_param_array(output_height_align, uint, NULL, 0644);
+MODULE_PARM_DESC(output_height_align,
+		 "Per Channel height alignment requied at output.");
+
+static unsigned int capture_height_align[XM2MSC_MAX_CHAN] = {
+					1, 1, 1, 1, 1, 1, 1, 1 };
+module_param_array(capture_height_align, uint, NULL, 0644);
+MODULE_PARM_DESC(capture_height_align,
+		 "Per channel height alignment requied at capture.");
+
+/* Xilinx Video Specific Color/Pixel Formats */
+enum xm2msc_pix_fmt {
+	XILINX_M2MSC_FMT_RGBX8		= 10,
+	XILINX_M2MSC_FMT_YUVX8		= 11,
+	XILINX_M2MSC_FMT_YUYV8		= 12,
+	XILINX_M2MSC_FMT_RGBX10		= 15,
+	XILINX_M2MSC_FMT_YUVX10		= 16,
+	XILINX_M2MSC_FMT_Y_UV8		= 18,
+	XILINX_M2MSC_FMT_Y_UV8_420	= 19,
+	XILINX_M2MSC_FMT_RGB8		= 20,
+	XILINX_M2MSC_FMT_YUV8		= 21,
+	XILINX_M2MSC_FMT_Y_UV10		= 22,
+	XILINX_M2MSC_FMT_Y_UV10_420	= 23,
+	XILINX_M2MSC_FMT_Y8		= 24,
+	XILINX_M2MSC_FMT_Y10		= 25,
+	XILINX_M2MSC_FMT_BGRX8		= 27,
+	XILINX_M2MSC_FMT_UYVY8		= 28,
+	XILINX_M2MSC_FMT_BGR8		= 29,
+};
+
+/**
+ * struct xm2msc_fmt - driver info for each of the supported video formats
+ * @name: human-readable device tree name for this entry
+ * @fourcc: standard format identifier
+ * @xm2msc_fmt: Xilinx Video Specific Color/Pixel Formats
+ * @num_buffs: number of physically non-contiguous data planes/buffs
+ */
+struct xm2msc_fmt {
+	char *name;
+	u32 fourcc;
+	enum xm2msc_pix_fmt xm2msc_fmt;
+	u32 num_buffs;
+};
+
+static const struct xm2msc_fmt formats[] = {
+	{
+		.name = "xbgr8888",
+		.fourcc = V4L2_PIX_FMT_BGRX32,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_RGBX8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "xvuy8888",
+		.fourcc = V4L2_PIX_FMT_XVUY32,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_YUVX8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "yuyv",
+		.fourcc = V4L2_PIX_FMT_YUYV,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_YUYV8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "xbgr2101010",
+		.fourcc = V4L2_PIX_FMT_XBGR30,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_RGBX10,
+		.num_buffs = 1,
+	},
+	{
+		.name = "yuvx2101010",
+		.fourcc = V4L2_PIX_FMT_XVUY10,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_YUVX10,
+		.num_buffs = 1,
+	},
+	{
+		.name = "nv16",
+		.fourcc = V4L2_PIX_FMT_NV16M,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV8,
+		.num_buffs = 2,
+	},
+	{
+		.name = "nv16",
+		.fourcc = V4L2_PIX_FMT_NV16,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "nv12",
+		.fourcc = V4L2_PIX_FMT_NV12M,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV8_420,
+		.num_buffs = 2,
+	},
+	{
+		.name = "nv12",
+		.fourcc = V4L2_PIX_FMT_NV12,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV8_420,
+		.num_buffs = 1,
+	},
+	{
+		.name = "bgr888",
+		.fourcc = V4L2_PIX_FMT_RGB24,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_RGB8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "vuy888",
+		.fourcc = V4L2_PIX_FMT_VUY24,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_YUV8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "xv20",
+		.fourcc = V4L2_PIX_FMT_XV20M,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV10,
+		.num_buffs = 2,
+	},
+	{
+		.name = "xv20",
+		.fourcc = V4L2_PIX_FMT_XV20,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV10,
+		.num_buffs = 1,
+	},
+	{
+		.name = "xv15",
+		.fourcc = V4L2_PIX_FMT_XV15M,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV10_420,
+		.num_buffs = 2,
+	},
+	{
+		.name = "xv15",
+		.fourcc = V4L2_PIX_FMT_XV15,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y_UV10_420,
+		.num_buffs = 1,
+	},
+	{
+		.name = "y8",
+		.fourcc = V4L2_PIX_FMT_GREY,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "y10",
+		.fourcc = V4L2_PIX_FMT_Y10,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_Y10,
+		.num_buffs = 1,
+	},
+	{
+		.name = "xrgb8888",
+		.fourcc = V4L2_PIX_FMT_XBGR32,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_BGRX8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "uyvy",
+		.fourcc = V4L2_PIX_FMT_UYVY,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_UYVY8,
+		.num_buffs = 1,
+	},
+	{
+		.name = "rgb888",
+		.fourcc = V4L2_PIX_FMT_BGR24,
+		.xm2msc_fmt = XILINX_M2MSC_FMT_BGR8,
+		.num_buffs = 1,
+	},
+};
+
+/**
+ * struct xm2msc_q_data - Per-queue, driver-specific private data
+ * There is one source queue and one destination queue for each m2m context.
+ * @width: frame width
+ * @height: frame height
+ * @stride: bytes per lines
+ * @nbuffs: Current number of buffs
+ * @bytesperline: bytes per line per plane
+ * @sizeimage: image size per plane
+ * @colorspace: supported colorspace
+ * @field: supported field value
+ * @fmt: format info
+ */
+struct xm2msc_q_data {
+	unsigned int width;
+	unsigned int height;
+	unsigned int stride;
+	unsigned int nbuffs;
+	unsigned int bytesperline[2];
+	unsigned int sizeimage[2];
+	enum v4l2_colorspace colorspace;
+	enum v4l2_field field;
+	const struct xm2msc_fmt *fmt;
+};
+
+/**
+ * struct xm2msc_chan_ctx - Scaler Channel Info, Per-Channel context
+ * @regs: IO mapped base address of the Channel
+ * @xm2msc_dev: Pointer to struct xm2m_msc_dev
+ * @num: HW Scaling Channel number
+ * @minor: Minor number of the video device
+ * @output_stride_align: required align stride value at output pad
+ * @capture_stride_align: required align stride valure at capture pad
+ * @output_height_align: required align height value at output pad
+ * @capture_height_align: required align heigh value at capture pad
+ * @status: channel status, CHAN_ATTACHED or CHAN_OPENED
+ * @frames: number of frames processed
+ * @vfd: V4L2 device
+ * @fh: v4l2 file handle
+ * @m2m_dev: m2m device
+ * @m2m_ctx: memory to memory context structure
+ * @q_data: src & dst queue data
+ */
+struct xm2msc_chan_ctx {
+	void __iomem *regs;
+	struct xm2m_msc_dev *xm2msc_dev;
+	u32 num;
+	u32 minor;
+	u32 output_stride_align;
+	u32 capture_stride_align;
+	u32 output_height_align;
+	u32 capture_height_align;
+	u8 status;
+	unsigned long frames;
+
+	struct video_device vfd;
+	struct v4l2_fh fh;
+	struct v4l2_m2m_dev *m2m_dev;
+	struct v4l2_m2m_ctx *m2m_ctx;
+
+	struct xm2msc_q_data q_data[2];
+};
+
+/**
+ * struct xm2m_msc_dev - Xilinx M2M Multi-scaler Device
+ * @dev: pointer to struct device instance used by the driver
+ * @regs: IO mapped base address of the HW/IP
+ * @irq: interrupt number
+ * @clk: video core clock
+ * @max_chan: maximum number of Scaling Channels
+ * @max_ht: maximum number of rows in a plane
+ * @max_wd: maximum number of column in a plane
+ * @taps: number of taps set in HW
+ * @supported_fmt: bitmap for all supported fmts by HW
+ * @dma_addr_size: Size of dma address pointer in IP (either 32 or 64)
+ * @ppc: Pixels per clock set in IP (1, 2 or 4)
+ * @rst_gpio: reset gpio handler
+ * @opened_chan: bitmap for all open channel
+ * @out_streamed_chan: bitmap for all out streamed channel
+ * @cap_streamed_chan: bitmap for all capture streamed channel
+ * @running_chan: currently running channels
+ * @device_busy: HW device is busy or not
+ * @isr_wait: flag to follow the ISR complete or not
+ * @isr_finished: Wait queue used to wait for IP to complete processing
+ * @v4l2_dev: main struct to for V4L2 device drivers
+ * @dev_mutex: lock for V4L2 device
+ * @mutex: lock for channel ctx
+ * @lock: lock used in IRQ
+ * @xm2msc_chan: arrey of channel context
+ * @hscaler_coeff: Array of filter coefficients for the Horizontal Scaler
+ * @vscaler_coeff: Array of filter coefficients for the Vertical Scaler
+ */
+struct xm2m_msc_dev {
+	struct device *dev;
+	void __iomem *regs;
+	int irq;
+	struct clk *clk;
+	u32 max_chan;
+	u32 max_ht;
+	u32 max_wd;
+	u32 taps;
+	u32 supported_fmt;
+	u32 dma_addr_size;
+	u8 ppc;
+	struct gpio_desc *rst_gpio;
+
+	u32 opened_chan;
+	u32 out_streamed_chan;
+	u32 cap_streamed_chan;
+	u32 running_chan;
+	bool device_busy;
+	bool isr_wait;
+	wait_queue_head_t isr_finished;
+
+	struct v4l2_device v4l2_dev;
+
+	struct mutex dev_mutex; /*the mutex for v4l2*/
+	struct mutex mutex; /*lock for bitmap reg*/
+	spinlock_t lock; /*IRQ lock*/
+
+	struct xm2msc_chan_ctx xm2msc_chan[XM2MSC_MAX_CHAN];
+	short hscaler_coeff[XSCALER_MAX_PHASES][XSCALER_MAX_TAPS];
+	short vscaler_coeff[XSCALER_MAX_PHASES][XSCALER_MAX_TAPS];
+};
+
+#define fh_to_chanctx(__fh) container_of(__fh, struct xm2msc_chan_ctx, fh)
+
+static inline u32 xm2msc_readreg(const void __iomem *addr)
+{
+	return ioread32(addr);
+}
+
+static inline void xm2msc_write64reg(void __iomem *addr, u64 value)
+{
+	iowrite32(lower_32_bits(value), addr);
+	iowrite32(upper_32_bits(value), (void __iomem *)(addr + 4));
+}
+
+static inline void xm2msc_writereg(void __iomem *addr, u32 value)
+{
+	iowrite32(value, addr);
+}
+
+static bool xm2msc_is_yuv_singlebuff(u32 fourcc)
+{
+	if (fourcc == V4L2_PIX_FMT_NV12 || fourcc == V4L2_PIX_FMT_XV15 ||
+	    fourcc ==  V4L2_PIX_FMT_NV16 || fourcc == V4L2_PIX_FMT_XV20)
+		return true;
+
+	return false;
+}
+
+static inline u32 xm2msc_yuv_1stplane_size(struct xm2msc_q_data *q_data,
+					   u32 row_align)
+{
+	return	q_data->bytesperline[0] * ALIGN(q_data->height, row_align);
+}
+
+static struct xm2msc_q_data *get_q_data(struct xm2msc_chan_ctx *chan_ctx,
+					enum v4l2_buf_type type)
+{
+	switch (type) {
+	case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE:
+	case V4L2_BUF_TYPE_VIDEO_OUTPUT:
+		return &chan_ctx->q_data[XM2MSC_CHAN_OUT];
+	case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE:
+	case V4L2_BUF_TYPE_VIDEO_CAPTURE:
+		return &chan_ctx->q_data[XM2MSC_CHAN_CAP];
+	default:
+		v4l2_err(&chan_ctx->xm2msc_dev->v4l2_dev,
+			 "Not supported Q type %d\n", type);
+	}
+	return NULL;
+}
+
+static u32 find_format_index(struct v4l2_format *f)
+{
+	const struct xm2msc_fmt *fmt;
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(formats); i++) {
+		fmt = &formats[i];
+		if (fmt->fourcc == f->fmt.pix_mp.pixelformat)
+			break;
+	}
+
+	return i;
+}
+
+static const struct xm2msc_fmt *find_format(struct v4l2_format *f)
+{
+	const struct xm2msc_fmt *fmt;
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(formats); i++) {
+		fmt = &formats[i];
+		if (fmt->fourcc == f->fmt.pix_mp.pixelformat)
+			break;
+	}
+
+	if (i == ARRAY_SIZE(formats))
+		return NULL;
+
+	return &formats[i];
+}
+
+static void
+xm2msc_hscaler_load_ext_coeff(struct xm2m_msc_dev *xm2msc,
+			      const short *coeff, u32 ntaps)
+{
+	unsigned int i, j, pad, offset;
+	const u32 nphases = XSCALER_MAX_PHASES;
+
+	/* Determine if coefficient needs padding (effective vs. max taps) */
+	pad = XSCALER_MAX_TAPS - ntaps;
+	offset = pad >> 1;
+
+	memset(xm2msc->hscaler_coeff, 0, sizeof(xm2msc->hscaler_coeff));
+
+	/* Load coefficients into scaler coefficient table */
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps; ++j)
+			xm2msc->hscaler_coeff[i][j + offset] =
+						coeff[i * ntaps + j];
+	}
+}
+
+static void xm2msc_hscaler_set_coeff(struct xm2msc_chan_ctx *chan_ctx,
+				     const u32 base_addr)
+{
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	int val, offset, rd_indx;
+	unsigned int i, j;
+	u32 ntaps = chan_ctx->xm2msc_dev->taps;
+	const u32 nphases = XSCALER_MAX_PHASES;
+
+	offset = (XSCALER_MAX_TAPS - ntaps) / 2;
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps / 2; j++) {
+			rd_indx = j * 2 + offset;
+			val = (xm2msc->hscaler_coeff[i][rd_indx + 1] <<
+			       XM2MSC_BITSHIFT_16) |
+			       (xm2msc->hscaler_coeff[i][rd_indx] &
+			       XM2MSC_MASK_LOW_16BITS);
+			 xm2msc_writereg((xm2msc->regs + base_addr) +
+				    ((i * ntaps / 2 + j) * 4), val);
+		}
+	}
+}
+
+static void
+xm2msc_vscaler_load_ext_coeff(struct xm2m_msc_dev *xm2msc,
+			      const short *coeff, const u32 ntaps)
+{
+	unsigned int i, j;
+	int pad, offset;
+	const u32 nphases = XSCALER_MAX_PHASES;
+
+	/* Determine if coefficient needs padding (effective vs. max taps) */
+	pad = XSCALER_MAX_TAPS - ntaps;
+	offset = pad ? (pad >> 1) : 0;
+
+	/* Zero Entire Array */
+	memset(xm2msc->vscaler_coeff, 0, sizeof(xm2msc->vscaler_coeff));
+
+	/* Load User defined coefficients into scaler coefficient table */
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps; ++j)
+			xm2msc->vscaler_coeff[i][j + offset] =
+						coeff[i * ntaps + j];
+	}
+}
+
+static void
+xm2msc_vscaler_set_coeff(struct xm2msc_chan_ctx *chan_ctx,
+			 const u32 base_addr)
+{
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	u32 val, i, j, offset, rd_indx;
+	u32 ntaps = chan_ctx->xm2msc_dev->taps;
+	const u32 nphases = XSCALER_MAX_PHASES;
+
+	offset = (XSCALER_MAX_TAPS - ntaps) / 2;
+
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps / 2; j++) {
+			rd_indx = j * 2 + offset;
+			val = (xm2msc->vscaler_coeff[i][rd_indx + 1] <<
+			       XM2MSC_BITSHIFT_16) |
+			       (xm2msc->vscaler_coeff[i][rd_indx] &
+			       XM2MSC_MASK_LOW_16BITS);
+			xm2msc_writereg((xm2msc->regs +
+				   base_addr) + ((i * ntaps / 2 + j) * 4), val);
+		}
+	}
+}
+
+static u32
+xm2msc_select_hcoeff(struct xm2msc_chan_ctx *chan_ctx, const short **coeff)
+{
+	u16 hscale_ratio;
+	u32 width_in = chan_ctx->q_data[XM2MSC_CHAN_OUT].width;
+	u32 width_out = chan_ctx->q_data[XM2MSC_CHAN_CAP].width;
+	u32 ntaps;
+
+	if (width_out < width_in) {
+		hscale_ratio = (width_in * 10) / width_out;
+
+		switch (chan_ctx->xm2msc_dev->taps) {
+		case XSCALER_TAPS_12:
+			if (hscale_ratio > 35) {
+				*coeff = &xhsc_coeff_taps12[0][0];
+				ntaps = XSCALER_TAPS_12;
+			} else if (hscale_ratio > 25) {
+				*coeff = &xhsc_coeff_taps10[0][0];
+				ntaps = XSCALER_TAPS_10;
+			} else if (hscale_ratio > 15) {
+				*coeff = &xhsc_coeff_taps8[0][0];
+				ntaps = XSCALER_TAPS_8;
+			} else {
+				*coeff = &xhsc_coeff_taps6[0][0];
+				ntaps = XSCALER_TAPS_6;
+			}
+		break;
+		case XSCALER_TAPS_10:
+			if (hscale_ratio > 25) {
+				*coeff = &xhsc_coeff_taps10[0][0];
+				ntaps = XSCALER_TAPS_10;
+			} else if (hscale_ratio > 15) {
+				*coeff = &xhsc_coeff_taps8[0][0];
+				ntaps = XSCALER_TAPS_8;
+			} else {
+				*coeff = &xhsc_coeff_taps6[0][0];
+				ntaps = XSCALER_TAPS_6;
+			}
+		break;
+		case XSCALER_TAPS_8:
+			if (hscale_ratio > 15) {
+				*coeff = &xhsc_coeff_taps8[0][0];
+				ntaps = XSCALER_TAPS_8;
+			} else {
+				*coeff = &xhsc_coeff_taps6[0][0];
+				ntaps = XSCALER_TAPS_6;
+			}
+		break;
+		default: /* or XSCALER_TAPS_6 */
+			*coeff = &xhsc_coeff_taps6[0][0];
+			ntaps = XSCALER_TAPS_6;
+		}
+	} else {
+		/*
+		 * Scale Up Mode will always use 6 tap filter
+		 * This also includes 1:1
+		 */
+		*coeff = &xhsc_coeff_taps6[0][0];
+		ntaps = XSCALER_TAPS_6;
+	}
+
+	return ntaps;
+}
+
+static u32
+xm2msc_select_vcoeff(struct xm2msc_chan_ctx *chan_ctx, const short **coeff)
+{
+	u16 vscale_ratio;
+	u32 height_in = chan_ctx->q_data[XM2MSC_CHAN_OUT].height;
+	u32 height_out = chan_ctx->q_data[XM2MSC_CHAN_CAP].height;
+	u32 ntaps;
+
+	if (height_out < height_in) {
+		vscale_ratio = (height_in * 10) / height_out;
+
+		switch (chan_ctx->xm2msc_dev->taps) {
+		case XSCALER_TAPS_12:
+			if (vscale_ratio > 35) {
+				*coeff = &xvsc_coeff_taps12[0][0];
+				ntaps = XSCALER_TAPS_12;
+			} else if (vscale_ratio > 25) {
+				*coeff = &xvsc_coeff_taps10[0][0];
+				ntaps = XSCALER_TAPS_10;
+			} else if (vscale_ratio > 15) {
+				*coeff = &xvsc_coeff_taps8[0][0];
+				ntaps = XSCALER_TAPS_8;
+			} else {
+				*coeff = &xvsc_coeff_taps6[0][0];
+				ntaps = XSCALER_TAPS_6;
+			}
+		break;
+		case XSCALER_TAPS_10:
+			if (vscale_ratio > 25) {
+				*coeff = &xvsc_coeff_taps10[0][0];
+				ntaps = XSCALER_TAPS_10;
+			} else if (vscale_ratio > 15) {
+				*coeff = &xvsc_coeff_taps8[0][0];
+				ntaps = XSCALER_TAPS_8;
+			} else {
+				*coeff = &xvsc_coeff_taps6[0][0];
+				ntaps = XSCALER_TAPS_6;
+			}
+		break;
+		case XSCALER_TAPS_8:
+			if (vscale_ratio > 15) {
+				*coeff = &xvsc_coeff_taps8[0][0];
+				ntaps = XSCALER_TAPS_8;
+			} else {
+				*coeff = &xvsc_coeff_taps6[0][0];
+				ntaps = XSCALER_TAPS_6;
+			}
+		break;
+		default: /* or XSCALER_TAPS_6 */
+			*coeff = &xvsc_coeff_taps6[0][0];
+			ntaps = XSCALER_TAPS_6;
+		}
+	} else {
+		/*
+		 * Scale Up Mode will always use 6 tap filter
+		 * This also includes 1:1
+		 */
+		*coeff = &xvsc_coeff_taps6[0][0];
+		ntaps = XSCALER_TAPS_6;
+	}
+
+	return ntaps;
+}
+
+static void xm2mvsc_initialize_coeff_banks(struct xm2msc_chan_ctx *chan_ctx)
+{
+	const short *coeff = NULL;
+	u32 ntaps;
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+
+	ntaps = xm2msc_select_hcoeff(chan_ctx, &coeff);
+	xm2msc_hscaler_load_ext_coeff(xm2msc, coeff, ntaps);
+	xm2msc_hscaler_set_coeff(chan_ctx, XM2MVSC_HFLTCOEFF(chan_ctx->num));
+
+	dev_dbg(xm2msc->dev, "htaps %d selected for chan %d\n",
+		ntaps, chan_ctx->num);
+
+	ntaps = xm2msc_select_vcoeff(chan_ctx, &coeff);
+	xm2msc_vscaler_load_ext_coeff(xm2msc, coeff, ntaps);
+	xm2msc_vscaler_set_coeff(chan_ctx, XM2MVSC_VFLTCOEFF(chan_ctx->num));
+
+	dev_dbg(xm2msc->dev, "vtaps %d selected for chan %d\n",
+		ntaps, chan_ctx->num);
+}
+
+static int xm2msc_set_chan_params(struct xm2msc_chan_ctx *chan_ctx,
+				  enum v4l2_buf_type type)
+{
+	struct xm2msc_q_data *q_data = get_q_data(chan_ctx, type);
+	const struct xm2msc_fmt *fmt;
+	void __iomem *base = chan_ctx->regs;
+
+	if (!q_data)
+		return -EINVAL;
+
+	fmt = q_data->fmt;
+
+	if (type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE) {
+		xm2msc_writereg(base + XM2MSC_WIDTHIN, q_data->width);
+		xm2msc_writereg(base + XM2MSC_HEIGHTIN, q_data->height);
+		xm2msc_writereg(base + XM2MSC_INPIXELFMT, fmt->xm2msc_fmt);
+		xm2msc_writereg(base + XM2MSC_INSTRIDE, q_data->stride);
+	} else {
+		xm2msc_writereg(base + XM2MSC_WIDTHOUT, q_data->width);
+		xm2msc_writereg(base + XM2MSC_HEIGHTOUT, q_data->height);
+		xm2msc_writereg(base + XM2MSC_OUTPIXELFMT, fmt->xm2msc_fmt);
+		xm2msc_writereg(base + XM2MSC_OUTSTRIDE, q_data->stride);
+	}
+
+	return 0;
+}
+
+static void xm2msc_set_chan_com_params(struct xm2msc_chan_ctx *chan_ctx)
+{
+	void __iomem *base = chan_ctx->regs;
+	struct xm2msc_q_data *out_q_data = &chan_ctx->q_data[XM2MSC_CHAN_OUT];
+	struct xm2msc_q_data *cap_q_data = &chan_ctx->q_data[XM2MSC_CHAN_CAP];
+	u32 pixel_rate;
+	u32 line_rate;
+
+	xm2mvsc_initialize_coeff_banks(chan_ctx);
+
+	pixel_rate = (out_q_data->width * XM2MSC_STEP_PRECISION) /
+		cap_q_data->width;
+	line_rate = (out_q_data->height * XM2MSC_STEP_PRECISION) /
+		cap_q_data->height;
+
+	xm2msc_writereg(base + XM2MSC_PIXELRATE, pixel_rate);
+	xm2msc_writereg(base + XM2MSC_LINERATE, line_rate);
+}
+
+static int xm2msc_program_allchan(struct xm2m_msc_dev *xm2msc)
+{
+	u32 chan;
+
+	for (chan = 0; chan < xm2msc->running_chan; chan++) {
+		struct xm2msc_chan_ctx *chan_ctx;
+		enum v4l2_buf_type type;
+		int ret;
+
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+		type = V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE;
+		ret = xm2msc_set_chan_params(chan_ctx, type);
+		if (ret)
+			return ret;
+
+		type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
+		ret = xm2msc_set_chan_params(chan_ctx, type);
+		if (ret)
+			return ret;
+		xm2msc_set_chan_com_params(chan_ctx);
+	}
+	return 0;
+}
+
+static void
+xm2msc_pr_q(struct device *dev, struct xm2msc_q_data *q, int chan,
+	    int type, const char *fun_name)
+{
+	unsigned int i;
+	const struct xm2msc_fmt *fmt = q->fmt;
+
+	if (type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		dev_dbg(dev, "\n\nOUTPUT Q (%d) Context from [[ %s ]]",
+			chan, fun_name);
+	else
+		dev_dbg(dev, "\n\nCAPTURE Q (%d) Context from [[ %s ]]",
+			chan, fun_name);
+
+	dev_dbg(dev, "width height stride clrspace field planes\n");
+	dev_dbg(dev, "  %d  %d    %d     %d       %d    %d\n",
+		q->width, q->height, q->stride,
+		q->colorspace, q->field, q->nbuffs);
+
+	for (i = 0; i < q->nbuffs; i++) {
+		dev_dbg(dev, "[plane %d ] bytesperline sizeimage\n", i);
+		dev_dbg(dev, "                %d        %d\n",
+			q->bytesperline[i], q->sizeimage[i]);
+	}
+
+	dev_dbg(dev, "fmt_name 4cc xlnx-fmt\n");
+	dev_dbg(dev, "%s %d %d\n",
+		fmt->name, fmt->fourcc, fmt->xm2msc_fmt);
+	dev_dbg(dev, "\n\n");
+}
+
+static void
+xm2msc_pr_status(struct xm2m_msc_dev *xm2msc,
+		 const char *fun_name)
+{
+	struct device *dev = xm2msc->dev;
+
+	dev_dbg(dev, "Status in %s\n", fun_name);
+	dev_dbg(dev, "opened_chan out_streamed_chan cap_streamed_chan\n");
+	dev_dbg(dev, "0x%x           0x%x               0x%x\n",
+		xm2msc->opened_chan, xm2msc->out_streamed_chan,
+		xm2msc->cap_streamed_chan);
+	dev_dbg(dev, "\n\n");
+}
+
+static void
+xm2msc_pr_chanctx(struct xm2msc_chan_ctx *ctx, const char *fun_name)
+{
+	struct device *dev = ctx->xm2msc_dev->dev;
+
+	dev_dbg(dev, "\n\n----- [[ %s ]]: Channel %d (0x%p) context -----\n",
+		fun_name, ctx->num, ctx);
+	dev_dbg(dev, "minor = %d\n", ctx->minor);
+	dev_dbg(dev, "reg mapped at %p\n", ctx->regs);
+	dev_dbg(dev, "xm2msc \tm2m_dev \tm2m_ctx\n");
+	dev_dbg(dev, "%p \t%p \t%p\n", ctx->xm2msc_dev,
+		ctx->m2m_dev, ctx->m2m_ctx);
+
+	if (ctx->status & CHAN_OPENED)
+		dev_dbg(dev, "Opened ");
+	if (ctx->status & CHAN_ATTACHED)
+		dev_dbg(dev, "and attached");
+	dev_dbg(dev, "\n");
+	dev_dbg(dev, "-----------------------------------\n");
+	dev_dbg(dev, "\n\n");
+}
+
+static void
+xm2msc_pr_screg(struct device *dev, const void __iomem *base)
+{
+	dev_dbg(dev, "Ctr, GIE,  IE,  IS   OUT\n");
+	dev_dbg(dev, "0x%x  0x%x   0x%x  0x%x  0x%x\n",
+		xm2msc_readreg(base + XM2MSC_AP_CTRL),
+		xm2msc_readreg(base + XM2MSC_GIE),
+		xm2msc_readreg(base + XM2MSC_IER),
+		xm2msc_readreg(base + XM2MSC_ISR),
+		xm2msc_readreg(base + XM2MSC_NUM_OUTS));
+}
+
+static void
+xm2msc_pr_chanreg(struct device *dev, struct xm2msc_chan_ctx *chan)
+{
+	const void __iomem *base = chan->regs;
+
+	dev_dbg(dev, "WIN HIN INPIXELFMT INSTRIDE SRCB0L/H SRCB1L/H\n");
+	dev_dbg(dev, "%d   %d     %d       %d      0x%x/0x%x      0x%x/0x%x\n",
+		xm2msc_readreg(base + XM2MSC_WIDTHIN),
+		xm2msc_readreg(base + XM2MSC_HEIGHTIN),
+		xm2msc_readreg(base + XM2MSC_INPIXELFMT),
+		xm2msc_readreg(base + XM2MSC_INSTRIDE),
+		xm2msc_readreg(base + XM2MSC_SRCIMGBUF0),
+		xm2msc_readreg(base + XM2MSC_SRCIMGBUF0 + 4),
+		xm2msc_readreg(base + XM2MSC_SRCIMGBUF1),
+		xm2msc_readreg(base + XM2MSC_SRCIMGBUF1 + 4));
+	dev_dbg(dev, "WOUT HOUT OUTPIXELFMT OUTSTRIDE DBUF0L/H DBUF1L/H\n");
+	dev_dbg(dev, "%d   %d     %d       %d      0x%x/0x%x      0x%x/0x%x\n",
+		xm2msc_readreg(base + XM2MSC_WIDTHOUT),
+		xm2msc_readreg(base + XM2MSC_HEIGHTOUT),
+		xm2msc_readreg(base + XM2MSC_OUTPIXELFMT),
+		xm2msc_readreg(base + XM2MSC_OUTSTRIDE),
+		xm2msc_readreg(base + XM2MSC_DSTIMGBUF0),
+		xm2msc_readreg(base + XM2MSC_DSTIMGBUF0 + 4),
+		chan->num == 4 ?
+		xm2msc_readreg(base +
+			       XM2MSC_DSTIMGBUF1 + XM2MSC_RESERVED_AREA) :
+			xm2msc_readreg(base + XM2MSC_DSTIMGBUF1),
+		chan->num == 4 ?
+		xm2msc_readreg(base +
+			       XM2MSC_DSTIMGBUF1 + XM2MSC_RESERVED_AREA + 4) :
+			xm2msc_readreg(base + XM2MSC_DSTIMGBUF1 + 4));
+
+	dev_dbg(dev, "LINERATE PIXELRATE\n");
+	dev_dbg(dev, "0x%x     0x%x\n",
+		xm2msc_readreg(base + XM2MSC_LINERATE),
+		xm2msc_readreg(base + XM2MSC_PIXELRATE));
+}
+
+static void
+xm2msc_pr_allchanreg(struct xm2m_msc_dev *xm2msc)
+{
+	unsigned int i;
+	struct xm2msc_chan_ctx *chan_ctx;
+	struct device *dev = xm2msc->dev;
+
+	xm2msc_pr_screg(xm2msc->dev, xm2msc->regs);
+
+	for (i = 0; i < xm2msc->running_chan; i++) {
+		chan_ctx = &xm2msc->xm2msc_chan[i];
+		dev_dbg(dev, "Regs val for channel %d\n", i);
+		dev_dbg(dev, "______________________________________________\n");
+		xm2msc_pr_chanreg(dev, chan_ctx);
+		dev_dbg(dev, "processed frames = %lu\n", chan_ctx->frames);
+		dev_dbg(dev, "______________________________________________\n");
+	}
+}
+
+static inline bool xm2msc_testbit(int num, u32 *addr)
+{
+	return (*addr & BIT(num));
+}
+
+static inline void xm2msc_setbit(int num, u32 *addr)
+{
+	*addr |= BIT(num);
+}
+
+static inline void xm2msc_clrbit(int num, u32 *addr)
+{
+	*addr &= ~BIT(num);
+}
+
+static void xm2msc_stop(struct xm2m_msc_dev *xm2msc)
+{
+	void __iomem *base = xm2msc->regs;
+	u32 data = xm2msc_readreg(base + XM2MSC_AP_CTRL);
+
+	data &= ~XM2MSC_AP_CTRL_START;
+	xm2msc_writereg(base + XM2MSC_AP_CTRL, data);
+}
+
+static void xm2msc_start(struct xm2m_msc_dev *xm2msc)
+{
+	void __iomem *base = xm2msc->regs;
+	u32 data = xm2msc_readreg(base + XM2MSC_AP_CTRL);
+
+	data |= XM2MSC_AP_CTRL_START;
+	xm2msc_writereg(base + XM2MSC_AP_CTRL, data);
+}
+
+static void xm2msc_set_chan(struct xm2msc_chan_ctx *ctx, bool state)
+{
+	mutex_lock(&ctx->xm2msc_dev->mutex);
+	if (state)
+		xm2msc_setbit(ctx->num, &ctx->xm2msc_dev->opened_chan);
+	else
+		xm2msc_clrbit(ctx->num, &ctx->xm2msc_dev->opened_chan);
+	mutex_unlock(&ctx->xm2msc_dev->mutex);
+}
+
+static void
+xm2msc_set_chan_stream(struct xm2msc_chan_ctx *ctx, bool state, int type)
+{
+	u32 *ptr;
+
+	if (type == XM2MSC_CHAN_OUT)
+		ptr = &ctx->xm2msc_dev->out_streamed_chan;
+	else
+		ptr = &ctx->xm2msc_dev->cap_streamed_chan;
+
+	spin_lock(&ctx->xm2msc_dev->lock);
+	if (state)
+		xm2msc_setbit(ctx->num, ptr);
+	else
+		xm2msc_clrbit(ctx->num, ptr);
+
+	spin_unlock(&ctx->xm2msc_dev->lock);
+}
+
+static int
+xm2msc_chk_chan_stream(struct xm2msc_chan_ctx *ctx, int type)
+{
+	u32 *ptr;
+	int ret;
+
+	if (type == XM2MSC_CHAN_OUT)
+		ptr = &ctx->xm2msc_dev->out_streamed_chan;
+	else
+		ptr = &ctx->xm2msc_dev->cap_streamed_chan;
+
+	mutex_lock(&ctx->xm2msc_dev->mutex);
+	ret = xm2msc_testbit(ctx->num, ptr);
+	mutex_unlock(&ctx->xm2msc_dev->mutex);
+
+	return ret;
+}
+
+static void xm2msc_set_fmt(struct xm2m_msc_dev *xm2msc, u32 index)
+{
+	xm2msc_setbit(index, &xm2msc->supported_fmt);
+}
+
+static int xm2msc_chk_fmt(struct xm2m_msc_dev *xm2msc, u32 index)
+{
+	return xm2msc_testbit(index, &xm2msc->supported_fmt);
+}
+
+static void xm2msc_reset(struct xm2m_msc_dev *xm2msc)
+{
+	gpiod_set_value_cansleep(xm2msc->rst_gpio, XM2MSC_RESET_ASSERT);
+	gpiod_set_value_cansleep(xm2msc->rst_gpio, XM2MSC_RESET_DEASSERT);
+}
+
+/*
+ * mem2mem callbacks
+ */
+static int xm2msc_job_ready(void *priv)
+{
+	struct xm2msc_chan_ctx *chan_ctx = priv;
+
+	if ((v4l2_m2m_num_src_bufs_ready(chan_ctx->m2m_ctx) > 0) &&
+	    (v4l2_m2m_num_dst_bufs_ready(chan_ctx->m2m_ctx) > 0))
+		return 1;
+	return 0;
+}
+
+static bool xm2msc_alljob_ready(struct xm2m_msc_dev *xm2msc)
+{
+	struct xm2msc_chan_ctx *chan_ctx;
+	unsigned int chan;
+
+	for (chan = 0; chan < xm2msc->running_chan; chan++) {
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+
+		if (!xm2msc_job_ready((void *)chan_ctx)) {
+			dev_dbg(xm2msc->dev, "chan %d not ready\n",
+				chan_ctx->num);
+			return false;
+		}
+	}
+
+	return true;
+}
+
+static void xm2msc_chan_abort_bufs(struct xm2msc_chan_ctx *chan_ctx)
+{
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	struct vb2_v4l2_buffer *dst_vb, *src_vb;
+
+	spin_lock(&xm2msc->lock);
+	dev_dbg(xm2msc->dev, "aborting all buffers\n");
+
+	while (v4l2_m2m_num_src_bufs_ready(chan_ctx->m2m_ctx) > 0) {
+		src_vb = v4l2_m2m_src_buf_remove(chan_ctx->m2m_ctx);
+		if (src_vb)
+			v4l2_m2m_buf_done(src_vb, VB2_BUF_STATE_ERROR);
+	}
+
+	while (v4l2_m2m_num_dst_bufs_ready(chan_ctx->m2m_ctx) > 0) {
+		dst_vb = v4l2_m2m_dst_buf_remove(chan_ctx->m2m_ctx);
+		if (dst_vb)
+			v4l2_m2m_buf_done(dst_vb, VB2_BUF_STATE_ERROR);
+	}
+
+	v4l2_m2m_job_finish(chan_ctx->m2m_dev, chan_ctx->m2m_ctx);
+	spin_unlock(&xm2msc->lock);
+}
+
+static void xm2msc_job_abort(void *priv)
+{
+	struct xm2msc_chan_ctx *chan_ctx = priv;
+
+	xm2msc_chan_abort_bufs(chan_ctx);
+
+	/*
+	 * Stream off the channel as job_abort may not always
+	 * be called after streamoff
+	 */
+	xm2msc_set_chan_stream(chan_ctx, false, XM2MSC_CHAN_OUT);
+	xm2msc_set_chan_stream(chan_ctx, false, XM2MSC_CHAN_CAP);
+}
+
+static int xm2msc_set_bufaddr(struct xm2m_msc_dev *xm2msc)
+{
+	unsigned int chan;
+	u32 row_align;
+	struct xm2msc_chan_ctx *chan_ctx;
+	struct vb2_v4l2_buffer *src_vb, *dst_vb;
+	void __iomem *base;
+	struct xm2msc_q_data *q_data;
+	dma_addr_t src_luma, dst_luma;
+	dma_addr_t src_croma, dst_croma;
+
+	if (!xm2msc_alljob_ready(xm2msc))
+		return -EINVAL;
+
+	for (chan = 0; chan < xm2msc->running_chan; chan++) {
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+		base = chan_ctx->regs;
+
+		src_vb = v4l2_m2m_next_src_buf(chan_ctx->m2m_ctx);
+		dst_vb = v4l2_m2m_next_dst_buf(chan_ctx->m2m_ctx);
+
+		if (!src_vb || !dst_vb) {
+			v4l2_err(&xm2msc->v4l2_dev, "buffer not found chan = %d\n",
+				 chan_ctx->num);
+			return -EINVAL;
+		}
+
+		src_luma = vb2_dma_contig_plane_dma_addr(&src_vb->vb2_buf, 0);
+		dst_luma = vb2_dma_contig_plane_dma_addr(&dst_vb->vb2_buf, 0);
+
+		q_data = &chan_ctx->q_data[XM2MSC_CHAN_OUT];
+		row_align = chan_ctx->output_height_align;
+		if (chan_ctx->q_data[XM2MSC_CHAN_OUT].nbuffs == 2)
+			/* fmts having 2 planes 2 buffers */
+			src_croma =
+				vb2_dma_contig_plane_dma_addr(&src_vb->vb2_buf,
+							      1);
+		else if (xm2msc_is_yuv_singlebuff(q_data->fmt->fourcc))
+			/* fmts having 2 planes 1 contiguous buffer */
+			src_croma = src_luma +
+				xm2msc_yuv_1stplane_size(q_data, row_align);
+		else /* fmts having 1 planes 1 contiguous buffer */
+			src_croma = 0;
+
+		q_data = &chan_ctx->q_data[XM2MSC_CHAN_CAP];
+		row_align = chan_ctx->capture_height_align;
+		if (chan_ctx->q_data[XM2MSC_CHAN_CAP].nbuffs == 2)
+			dst_croma =
+				vb2_dma_contig_plane_dma_addr(&dst_vb->vb2_buf,
+							      1);
+		else if (xm2msc_is_yuv_singlebuff(q_data->fmt->fourcc))
+			dst_croma = dst_luma +
+				xm2msc_yuv_1stplane_size(q_data, row_align);
+		else
+			dst_croma = 0;
+
+		if (xm2msc->dma_addr_size == 64 &&
+		    sizeof(dma_addr_t) == sizeof(u64)) {
+			xm2msc_write64reg(base + XM2MSC_SRCIMGBUF0, src_luma);
+			xm2msc_write64reg(base + XM2MSC_SRCIMGBUF1, src_croma);
+			xm2msc_write64reg(base + XM2MSC_DSTIMGBUF0, dst_luma);
+			if (chan_ctx->num == 4) /* TODO: To be fixed in HW */
+				xm2msc_write64reg(base + XM2MSC_DSTIMGBUF1 +
+						  XM2MSC_RESERVED_AREA,
+						  dst_croma);
+			else
+				xm2msc_write64reg(base + XM2MSC_DSTIMGBUF1,
+						  dst_croma);
+		} else {
+			xm2msc_writereg(base + XM2MSC_SRCIMGBUF0, src_luma);
+			xm2msc_writereg(base + XM2MSC_SRCIMGBUF1, src_croma);
+			xm2msc_writereg(base + XM2MSC_DSTIMGBUF0, dst_luma);
+			if (chan_ctx->num == 4) /* TODO: To be fixed in HW */
+				xm2msc_writereg(base + XM2MSC_DSTIMGBUF1 +
+						XM2MSC_RESERVED_AREA,
+						dst_croma);
+			else
+				xm2msc_writereg(base + XM2MSC_DSTIMGBUF1,
+						dst_croma);
+		}
+	}
+	return 0;
+}
+
+static void xm2msc_job_finish(struct xm2m_msc_dev *xm2msc)
+{
+	unsigned int chan;
+
+	for (chan = 0; chan < xm2msc->running_chan; chan++) {
+		struct xm2msc_chan_ctx *chan_ctx;
+
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+		v4l2_m2m_job_finish(chan_ctx->m2m_dev, chan_ctx->m2m_ctx);
+	}
+}
+
+static void xm2msc_job_done(struct xm2m_msc_dev *xm2msc)
+{
+	u32 chan;
+
+	for (chan = 0; chan < xm2msc->running_chan; chan++) {
+		struct xm2msc_chan_ctx *chan_ctx;
+		struct vb2_v4l2_buffer *src_vb, *dst_vb;
+		unsigned long flags;
+
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+
+		src_vb = v4l2_m2m_src_buf_remove(chan_ctx->m2m_ctx);
+		dst_vb = v4l2_m2m_dst_buf_remove(chan_ctx->m2m_ctx);
+
+		if (src_vb && dst_vb) {
+			dst_vb->vb2_buf.timestamp = src_vb->vb2_buf.timestamp;
+			dst_vb->timecode = src_vb->timecode;
+			dst_vb->flags &= ~V4L2_BUF_FLAG_TSTAMP_SRC_MASK;
+			dst_vb->flags |=
+			    src_vb->flags & V4L2_BUF_FLAG_TSTAMP_SRC_MASK;
+
+			spin_lock_irqsave(&xm2msc->lock, flags);
+			v4l2_m2m_buf_done(src_vb, VB2_BUF_STATE_DONE);
+			v4l2_m2m_buf_done(dst_vb, VB2_BUF_STATE_DONE);
+			spin_unlock_irqrestore(&xm2msc->lock, flags);
+		}
+		chan_ctx->frames++;
+	}
+}
+
+static void xm2msc_device_run(void *priv)
+{
+	struct xm2msc_chan_ctx *chan_ctx = priv;
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	void __iomem *base = xm2msc->regs;
+	unsigned long flags;
+	int ret;
+
+	spin_lock_irqsave(&xm2msc->lock, flags);
+	if (xm2msc->device_busy) {
+		spin_unlock_irqrestore(&xm2msc->lock, flags);
+		return;
+	}
+	xm2msc->device_busy = true;
+
+	if (xm2msc->running_chan != NUM_STREAM(xm2msc)) {
+		dev_dbg(xm2msc->dev, "Running chan was %d\n",
+			xm2msc->running_chan);
+		xm2msc->running_chan = NUM_STREAM(xm2msc);
+
+		/* IP need reset for updating of XM2MSC_NUM_OUT */
+		xm2msc_reset(xm2msc);
+		xm2msc_writereg(base + XM2MSC_NUM_OUTS, xm2msc->running_chan);
+		ret = xm2msc_program_allchan(xm2msc);
+		if (ret) {
+			spin_unlock_irqrestore(&xm2msc->lock, flags);
+			xm2msc->device_busy = false;
+			return;
+		}
+	}
+	spin_unlock_irqrestore(&xm2msc->lock, flags);
+
+	dev_dbg(xm2msc->dev, "Running chan = %d\n", xm2msc->running_chan);
+	if (!xm2msc->running_chan) {
+		xm2msc->device_busy = false;
+		return;
+	}
+
+	ret = xm2msc_set_bufaddr(xm2msc);
+	if (ret) {
+		/*
+		 * All channel does not have buffer
+		 * Currently we do not handle the removal of any Intermediate
+		 * channel while streaming is going on
+		 */
+		if (xm2msc->out_streamed_chan || xm2msc->cap_streamed_chan)
+			dev_dbg(xm2msc->dev,
+				"Buffer not available, streaming chan 0x%x\n",
+				xm2msc->cap_streamed_chan);
+
+		xm2msc->device_busy = false;
+		return;
+	}
+
+	xm2msc_writereg(base + XM2MSC_GIE, XM2MSC_GIE_EN);
+	xm2msc_writereg(base + XM2MSC_IER, XM2MSC_ISR_DONE);
+
+	xm2msc_pr_status(xm2msc, __func__);
+	xm2msc_pr_screg(xm2msc->dev, base);
+	xm2msc_pr_allchanreg(xm2msc);
+
+	xm2msc_start(xm2msc);
+
+	xm2msc->isr_wait = true;
+	wait_event(xm2msc->isr_finished, !xm2msc->isr_wait);
+
+	xm2msc_job_done(xm2msc);
+
+	xm2msc->device_busy = false;
+
+	if (xm2msc_alljob_ready(xm2msc))
+		xm2msc_device_run(xm2msc->xm2msc_chan);
+
+	xm2msc_job_finish(xm2msc);
+}
+
+static irqreturn_t xm2msc_isr(int irq, void *data)
+{
+	struct xm2m_msc_dev *xm2msc = (struct xm2m_msc_dev *)data;
+	void __iomem *base = xm2msc->regs;
+	u32 status;
+
+	status = xm2msc_readreg(base + XM2MSC_ISR);
+	if (!(status & XM2MSC_ISR_DONE))
+		return IRQ_NONE;
+
+	xm2msc_writereg(base + XM2MSC_ISR, status & XM2MSC_ISR_DONE);
+
+	xm2msc_stop(xm2msc);
+
+	xm2msc->isr_wait = false;
+	wake_up(&xm2msc->isr_finished);
+
+	return IRQ_HANDLED;
+}
+
+static int xm2msc_streamon(struct file *file, void *fh,
+			   enum v4l2_buf_type type)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_streamon(file, chan_ctx->m2m_ctx, type);
+}
+
+static int xm2msc_streamoff(struct file *file, void *fh,
+			    enum v4l2_buf_type type)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+	int ret;
+
+	ret = v4l2_m2m_streamoff(file, chan_ctx->m2m_ctx, type);
+
+	/* Check if any channel is still running */
+	xm2msc_device_run(chan_ctx);
+	return ret;
+}
+
+static int xm2msc_qbuf(struct file *file, void *fh, struct v4l2_buffer *buf)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_qbuf(file, chan_ctx->m2m_ctx, buf);
+}
+
+static int xm2msc_dqbuf(struct file *file, void *fh, struct v4l2_buffer *buf)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_dqbuf(file, chan_ctx->m2m_ctx, buf);
+}
+
+static int xm2msc_expbuf(struct file *file, void *fh,
+			 struct v4l2_exportbuffer *eb)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_expbuf(file, chan_ctx->m2m_ctx, eb);
+}
+
+static int xm2msc_createbufs(struct file *file, void *fh,
+			     struct v4l2_create_buffers *cb)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_create_bufs(file, chan_ctx->m2m_ctx, cb);
+}
+
+static int xm2msc_reqbufs(struct file *file, void *fh,
+			  struct v4l2_requestbuffers *reqbufs)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_reqbufs(file, chan_ctx->m2m_ctx, reqbufs);
+}
+
+static int xm2msc_querybuf(struct file *file, void *fh,
+			   struct v4l2_buffer *buf)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return v4l2_m2m_querybuf(file, chan_ctx->m2m_ctx, buf);
+}
+
+static void
+xm2msc_cal_imagesize(struct xm2msc_chan_ctx *chan_ctx,
+		     struct xm2msc_q_data *q_data, u32 type)
+{
+	unsigned int i;
+	u32 fourcc = q_data->fmt->fourcc;
+	u32 height = q_data->height;
+
+	if (type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		height = ALIGN(height, chan_ctx->output_height_align);
+	else if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		height = ALIGN(height, chan_ctx->capture_height_align);
+
+	for (i = 0; i < q_data->nbuffs; i++) {
+		q_data->bytesperline[i] = q_data->stride;
+		q_data->sizeimage[i] = q_data->stride * height;
+	}
+
+	switch (fourcc) {
+	case V4L2_PIX_FMT_NV12:
+	case V4L2_PIX_FMT_XV15:
+		/*
+		 * Adding chroma plane size as NV12/XV15
+		 * have a contiguous buffer for luma and chroma
+		 */
+		q_data->sizeimage[0] +=
+				q_data->stride * (height / 2);
+		break;
+	case V4L2_PIX_FMT_NV12M:
+	case V4L2_PIX_FMT_XV15M:
+		q_data->sizeimage[1] =
+				q_data->stride * (height / 2);
+		break;
+	default:
+		break;
+	}
+}
+
+static unsigned int
+xm2msc_cal_stride(unsigned int width, enum xm2msc_pix_fmt xfmt, u8 ppc)
+{
+	unsigned int stride;
+	u32 align;
+
+	/* Stride in Bytes = (Width × Bytes per Pixel); */
+	switch (xfmt) {
+	case XILINX_M2MSC_FMT_RGBX8:
+	case XILINX_M2MSC_FMT_YUVX8:
+	case XILINX_M2MSC_FMT_RGBX10:
+	case XILINX_M2MSC_FMT_YUVX10:
+	case XILINX_M2MSC_FMT_BGRX8:
+		stride = width * 4;
+		break;
+	case XILINX_M2MSC_FMT_YUYV8:
+	case XILINX_M2MSC_FMT_UYVY8:
+		stride = width * 2;
+		break;
+	case XILINX_M2MSC_FMT_Y_UV8:
+	case XILINX_M2MSC_FMT_Y_UV8_420:
+	case XILINX_M2MSC_FMT_Y8:
+		stride = width * 1;
+		break;
+	case XILINX_M2MSC_FMT_RGB8:
+	case XILINX_M2MSC_FMT_YUV8:
+	case XILINX_M2MSC_FMT_BGR8:
+		stride = width * 3;
+		break;
+	case XILINX_M2MSC_FMT_Y_UV10:
+	case XILINX_M2MSC_FMT_Y_UV10_420:
+	case XILINX_M2MSC_FMT_Y10:
+		/* 4 bytes per 3 pixels */
+		stride = DIV_ROUND_UP(width * 4, 3);
+		break;
+	default:
+		stride = 0;
+	}
+
+	/* The data size is 64*pixels per clock bits */
+	align = ppc * XM2MSC_ALIGN_MUL;
+	stride = ALIGN(stride, align);
+
+	return stride;
+}
+
+static int
+vidioc_try_fmt(struct xm2msc_chan_ctx *chan_ctx, struct v4l2_format *f)
+{
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	struct v4l2_pix_format_mplane *pix = &f->fmt.pix_mp;
+	struct xm2msc_q_data *q_data;
+	struct vb2_queue *vq;
+	int index;
+
+	if (pix->width < XM2MSC_MIN_WIDTH || pix->width > xm2msc->max_wd ||
+	    pix->height < XM2MSC_MIN_HEIGHT || pix->height > xm2msc->max_ht)
+		dev_dbg(xm2msc->dev,
+			"Wrong input parameters %d, wxh: %dx%d.\n",
+			f->type, f->fmt.pix.width, f->fmt.pix.height);
+
+	/* The width value must be a multiple of pixels per clock */
+	if (pix->width % chan_ctx->xm2msc_dev->ppc) {
+		dev_dbg(xm2msc->dev,
+			"Wrong align parameters %d, wxh: %dx%d.\n",
+			f->type, f->fmt.pix.width, f->fmt.pix.height);
+		pix->width = ALIGN(pix->width, chan_ctx->xm2msc_dev->ppc);
+	}
+
+	/*
+	 * V4L2 specification suggests the driver corrects the
+	 * format struct if any of the dimensions is unsupported
+	 */
+	if (pix->height < XM2MSC_MIN_HEIGHT)
+		pix->height = XM2MSC_MIN_HEIGHT;
+	else if (pix->height > xm2msc->max_ht)
+		pix->height = xm2msc->max_ht;
+
+	if (pix->width < XM2MSC_MIN_WIDTH)
+		pix->width = XM2MSC_MIN_WIDTH;
+	else if (pix->width > xm2msc->max_wd)
+		pix->width = xm2msc->max_wd;
+
+	vq = v4l2_m2m_get_vq(chan_ctx->m2m_ctx, (enum v4l2_buf_type)f->type);
+	if (!vq)
+		return -EINVAL;
+
+	q_data = get_q_data(chan_ctx, (enum v4l2_buf_type)f->type);
+	if (!q_data)
+		return -EINVAL;
+
+	if (vb2_is_busy(vq)) {
+		v4l2_err(&xm2msc->v4l2_dev,
+			 "%s queue busy\n", __func__);
+		return -EBUSY;
+	}
+
+	q_data->fmt = find_format(f);
+	index = find_format_index(f);
+	if (!q_data->fmt || index == ARRAY_SIZE(formats) ||
+	    !xm2msc_chk_fmt(xm2msc, index)) {
+		v4l2_err(&xm2msc->v4l2_dev,
+			 "Couldn't set format type %d, wxh: %dx%d. ",
+			 f->type, f->fmt.pix.width, f->fmt.pix.height);
+		v4l2_err(&xm2msc->v4l2_dev,
+			 "fmt: %d, field: %d\n",
+			 f->fmt.pix.pixelformat, f->fmt.pix.field);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void xm2msc_get_align(struct xm2msc_chan_ctx *chan_ctx)
+{
+	/*
+	 * TODO: This is a temporary solution, will be reverted once stride and
+	 * height align value come from application.
+	 */
+	chan_ctx->output_stride_align = output_stride_align[chan_ctx->num];
+	chan_ctx->capture_stride_align = capture_stride_align[chan_ctx->num];
+	chan_ctx->output_height_align = output_height_align[chan_ctx->num];
+	chan_ctx->capture_height_align = capture_height_align[chan_ctx->num];
+	if (output_stride_align[chan_ctx->num] != 1 ||
+	    capture_stride_align[chan_ctx->num] != 1 ||
+	    output_height_align[chan_ctx->num] != 1 ||
+	    capture_height_align[chan_ctx->num] != 1) {
+		dev_info(chan_ctx->xm2msc_dev->dev,
+			 "You entered values other than default values.\n");
+		dev_info(chan_ctx->xm2msc_dev->dev,
+			 "Please note this may not be available for longer");
+		dev_info(chan_ctx->xm2msc_dev->dev,
+			 "and align values will come from application\n");
+		dev_info(chan_ctx->xm2msc_dev->dev,
+			 "value entered are -\n"
+			 "output_stride_align = %d\n"
+			 "output_height_align = %d\n"
+			 "capture_stride_align = %d\n"
+			 "capture_height_align = %d\n",
+			chan_ctx->output_stride_align,
+			chan_ctx->output_height_align,
+			chan_ctx->capture_stride_align,
+			chan_ctx->capture_height_align);
+	}
+}
+
+static int
+vidioc_s_fmt(struct xm2msc_chan_ctx *chan_ctx, struct v4l2_format *f)
+{
+	struct v4l2_pix_format_mplane *pix = &f->fmt.pix_mp;
+	struct xm2msc_q_data *q_data;
+	unsigned int i;
+	unsigned int align = 1;
+
+	q_data = get_q_data(chan_ctx, (enum v4l2_buf_type)f->type);
+	if (!q_data)
+		return -EINVAL;
+
+	q_data->width = pix->width;
+	q_data->height = pix->height;
+	q_data->stride = xm2msc_cal_stride(pix->width,
+					   q_data->fmt->xm2msc_fmt,
+					   chan_ctx->xm2msc_dev->ppc);
+
+	xm2msc_get_align(chan_ctx);
+
+	if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		align = chan_ctx->output_stride_align;
+	else if (f->type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		align = chan_ctx->capture_stride_align;
+
+	q_data->stride = ALIGN(q_data->stride, align);
+
+	q_data->colorspace = (enum v4l2_colorspace)pix->colorspace;
+	q_data->field = (enum v4l2_field)pix->field;
+	q_data->nbuffs = q_data->fmt->num_buffs;
+
+	xm2msc_cal_imagesize(chan_ctx, q_data, f->type);
+
+	for (i = 0; i < q_data->nbuffs; i++) {
+		pix->plane_fmt[i].bytesperline = q_data->bytesperline[i];
+		pix->plane_fmt[i].sizeimage = q_data->sizeimage[i];
+	}
+
+	xm2msc_pr_q(chan_ctx->xm2msc_dev->dev, q_data,
+		    chan_ctx->num, f->type, __func__);
+
+	return 0;
+}
+
+static int xm2msc_try_fmt_vid_out(struct file *file, void *fh,
+				  struct v4l2_format *f)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return vidioc_try_fmt(chan_ctx, f);
+}
+
+static int xm2msc_try_fmt_vid_cap(struct file *file, void *fh,
+				  struct v4l2_format *f)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return vidioc_try_fmt(chan_ctx, f);
+}
+
+static int xm2msc_s_fmt_vid_cap(struct file *file, void *fh,
+				struct v4l2_format *f)
+{
+	int ret;
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	ret = xm2msc_try_fmt_vid_cap(file, fh, f);
+	if (ret)
+		return ret;
+	return vidioc_s_fmt(chan_ctx, f);
+}
+
+static int xm2msc_s_fmt_vid_out(struct file *file, void *fh,
+				struct v4l2_format *f)
+{
+	int ret;
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	ret = xm2msc_try_fmt_vid_out(file, fh, f);
+	if (ret)
+		return ret;
+
+	return vidioc_s_fmt(chan_ctx, f);
+}
+
+static int vidioc_g_fmt(struct xm2msc_chan_ctx *chan_ctx, struct v4l2_format *f)
+{
+	struct vb2_queue *vq;
+	struct xm2msc_q_data *q_data;
+	struct v4l2_pix_format_mplane *pix = &f->fmt.pix_mp;
+	unsigned int i;
+
+	vq = v4l2_m2m_get_vq(chan_ctx->m2m_ctx, (enum v4l2_buf_type)f->type);
+	if (!vq)
+		return -EINVAL;
+
+	q_data = get_q_data(chan_ctx, (enum v4l2_buf_type)f->type);
+	if (!q_data)
+		return -EINVAL;
+
+	pix->width = q_data->width;
+	pix->height = q_data->height;
+	pix->field = V4L2_FIELD_NONE;
+	pix->pixelformat = q_data->fmt->fourcc;
+	pix->colorspace = q_data->colorspace;
+	pix->num_planes = q_data->nbuffs;
+
+	for (i = 0; i < pix->num_planes; i++) {
+		pix->plane_fmt[i].bytesperline = q_data->bytesperline[i];
+		pix->plane_fmt[i].sizeimage = q_data->sizeimage[i];
+	}
+
+	return 0;
+}
+
+static int xm2msc_g_fmt_vid_out(struct file *file, void *fh,
+				struct v4l2_format *f)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return vidioc_g_fmt(chan_ctx, f);
+}
+
+static int xm2msc_g_fmt_vid_cap(struct file *file, void *fh,
+				struct v4l2_format *f)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	return vidioc_g_fmt(chan_ctx, f);
+}
+
+static int enum_fmt(struct xm2m_msc_dev *xm2msc, struct v4l2_fmtdesc *f)
+{
+	const struct xm2msc_fmt *fmt;
+	unsigned int i, enabled = 0;
+
+	for (i = 0; i < ARRAY_SIZE(formats); i++) {
+		if (xm2msc_chk_fmt(xm2msc, i) && enabled++ == f->index)
+			break;
+	}
+
+	if (i == ARRAY_SIZE(formats))
+		/* Format not found */
+		return -EINVAL;
+
+	/* Format found */
+	fmt = &formats[i];
+	strlcpy((char *)f->description, (char *)fmt->name,
+		sizeof(f->description));
+	f->pixelformat = fmt->fourcc;
+
+	return 0;
+}
+
+static int xm2msc_enum_fmt_vid_cap(struct file *file, void *fh,
+				   struct v4l2_fmtdesc *f)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	if (f->type != V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		return -EINVAL;
+
+	return enum_fmt(chan_ctx->xm2msc_dev, f);
+}
+
+static int xm2msc_enum_fmt_vid_out(struct file *file, void *fh,
+				   struct v4l2_fmtdesc *f)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+
+	if (f->type != V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		return -EINVAL;
+
+	return enum_fmt(chan_ctx->xm2msc_dev, f);
+}
+
+static int xm2msc_querycap(struct file *file, void *fh,
+			   struct v4l2_capability *cap)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(fh);
+	struct video_device *vfd = &chan_ctx->vfd;
+
+	strncpy((char *)cap->driver, XM2MSC_DRIVER_NAME,
+		sizeof(cap->driver) - 1);
+	strncpy((char *)cap->card, XM2MSC_DRIVER_NAME, sizeof(cap->card) - 1);
+	snprintf((char *)cap->bus_info, sizeof(cap->bus_info),
+		 "platform:%s", XM2MSC_DRIVER_NAME);
+	cap->device_caps = vfd->device_caps;
+	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
+
+	return 0;
+}
+
+static int xm2msc_queue_setup(struct vb2_queue *vq,
+			      unsigned int *nbuffers, unsigned int *nplanes,
+			      unsigned int sizes[], struct device *alloc_devs[])
+{
+	unsigned int i;
+	struct xm2msc_chan_ctx *chan_ctx = vb2_get_drv_priv(vq);
+	struct xm2msc_q_data *q_data;
+
+	q_data = get_q_data(chan_ctx, (enum v4l2_buf_type)vq->type);
+	if (!q_data)
+		return -EINVAL;
+
+	*nplanes = q_data->nbuffs;
+
+	for (i = 0; i < *nplanes; i++)
+		sizes[i] = q_data->sizeimage[i];
+
+	dev_dbg(chan_ctx->xm2msc_dev->dev, "get %d buffer(s) of size %d",
+		*nbuffers, sizes[0]);
+	if (q_data->nbuffs == 2)
+		dev_dbg(chan_ctx->xm2msc_dev->dev, " and %d\n", sizes[1]);
+
+	return 0;
+}
+
+static int xm2msc_buf_prepare(struct vb2_buffer *vb)
+{
+	struct xm2msc_chan_ctx *chan_ctx = vb2_get_drv_priv(vb->vb2_queue);
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	struct xm2msc_q_data *q_data;
+	unsigned int i, num_buffs;
+
+	q_data = get_q_data(chan_ctx, (enum v4l2_buf_type)vb->vb2_queue->type);
+	if (!q_data)
+		return -EINVAL;
+	num_buffs = q_data->nbuffs;
+
+	for (i = 0; i < num_buffs; i++) {
+		if (vb2_plane_size(vb, i) < q_data->sizeimage[i]) {
+			v4l2_err(&xm2msc->v4l2_dev, "data will not fit into plane ");
+				   v4l2_err(&xm2msc->v4l2_dev, "(%lu < %lu)\n",
+					    vb2_plane_size(vb, i),
+					    (long)q_data->sizeimage[i]);
+			return -EINVAL;
+		}
+	}
+
+	for (i = 0; i < num_buffs; i++)
+		vb2_set_plane_payload(vb, i, q_data->sizeimage[i]);
+
+	return 0;
+}
+
+static void xm2msc_buf_queue(struct vb2_buffer *vb)
+{
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+	struct xm2msc_chan_ctx *chan_ctx = vb2_get_drv_priv(vb->vb2_queue);
+
+	v4l2_m2m_buf_queue(chan_ctx->m2m_ctx, vbuf);
+}
+
+static void xm2msc_return_all_buffers(struct xm2msc_chan_ctx *chan_ctx,
+				      struct vb2_queue *q,
+				      enum vb2_buffer_state state)
+{
+	struct vb2_v4l2_buffer *vb;
+	unsigned long flags;
+
+	for (;;) {
+		if (V4L2_TYPE_IS_OUTPUT(q->type))
+			vb = v4l2_m2m_src_buf_remove(chan_ctx->m2m_ctx);
+		else
+			vb = v4l2_m2m_dst_buf_remove(chan_ctx->m2m_ctx);
+		if (!vb)
+			break;
+		spin_lock_irqsave(&chan_ctx->xm2msc_dev->lock, flags);
+		v4l2_m2m_buf_done(vb, state);
+		spin_unlock_irqrestore(&chan_ctx->xm2msc_dev->lock, flags);
+	}
+}
+
+static int xm2msc_start_streaming(struct vb2_queue *q, unsigned int count)
+{
+	struct xm2msc_chan_ctx *chan_ctx = vb2_get_drv_priv(q);
+	static struct xm2msc_q_data *q_data;
+	int type;
+	int ret;
+
+	if (V4L2_TYPE_IS_OUTPUT(q->type))
+		xm2msc_set_chan_stream(chan_ctx, true, XM2MSC_CHAN_OUT);
+	else
+		xm2msc_set_chan_stream(chan_ctx, true, XM2MSC_CHAN_CAP);
+
+	ret = xm2msc_set_chan_params(chan_ctx, (enum v4l2_buf_type)q->type);
+	if (ret)
+		return ret;
+
+	if (xm2msc_chk_chan_stream(chan_ctx, XM2MSC_CHAN_CAP) &&
+	    xm2msc_chk_chan_stream(chan_ctx, XM2MSC_CHAN_OUT))
+		xm2msc_set_chan_com_params(chan_ctx);
+
+	type = V4L2_TYPE_IS_OUTPUT(q->type) ?
+		V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE :
+		V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
+	q_data = get_q_data(chan_ctx, (enum v4l2_buf_type)type);
+	xm2msc_pr_q(chan_ctx->xm2msc_dev->dev, q_data, chan_ctx->num,
+		    type, __func__);
+	xm2msc_pr_status(chan_ctx->xm2msc_dev, __func__);
+
+	return 0;
+}
+
+static void xm2msc_stop_streaming(struct vb2_queue *q)
+{
+	struct xm2msc_chan_ctx *chan_ctx = vb2_get_drv_priv(q);
+
+	xm2msc_return_all_buffers(chan_ctx, q, VB2_BUF_STATE_ERROR);
+
+	if (V4L2_TYPE_IS_OUTPUT(q->type))
+		xm2msc_set_chan_stream(chan_ctx, false, XM2MSC_CHAN_OUT);
+	else
+		xm2msc_set_chan_stream(chan_ctx, false, XM2MSC_CHAN_CAP);
+}
+
+static const struct vb2_ops xm2msc_qops = {
+	.queue_setup = xm2msc_queue_setup,
+	.buf_prepare = xm2msc_buf_prepare,
+	.buf_queue = xm2msc_buf_queue,
+	.start_streaming = xm2msc_start_streaming,
+	.stop_streaming = xm2msc_stop_streaming,
+};
+
+static int queue_init(void *priv, struct vb2_queue *src_vq,
+		      struct vb2_queue *dst_vq)
+{
+	struct xm2msc_chan_ctx *chan_ctx = priv;
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	int ret;
+
+	memset(src_vq, 0, sizeof(*src_vq));
+	src_vq->type = V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE;
+	src_vq->io_modes = VB2_DMABUF | VB2_MMAP | VB2_USERPTR;
+	src_vq->drv_priv = chan_ctx;
+	src_vq->buf_struct_size = sizeof(struct v4l2_m2m_buffer);
+	src_vq->ops = &xm2msc_qops;
+	src_vq->mem_ops = &vb2_dma_contig_memops;
+	src_vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_COPY;
+	src_vq->lock = &xm2msc->dev_mutex;
+	src_vq->dev = xm2msc->v4l2_dev.dev;
+
+	ret = vb2_queue_init(src_vq);
+	if (ret)
+		return ret;
+
+	memset(dst_vq, 0, sizeof(*dst_vq));
+	dst_vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE;
+	dst_vq->io_modes = VB2_MMAP | VB2_DMABUF | VB2_USERPTR;
+	dst_vq->drv_priv = chan_ctx;
+	dst_vq->buf_struct_size = sizeof(struct v4l2_m2m_buffer);
+	dst_vq->ops = &xm2msc_qops;
+	dst_vq->mem_ops = &vb2_dma_contig_memops;
+	dst_vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_COPY;
+	dst_vq->lock = &xm2msc->dev_mutex;
+	dst_vq->dev = xm2msc->v4l2_dev.dev;
+
+	return vb2_queue_init(dst_vq);
+}
+
+static const struct v4l2_ioctl_ops xm2msc_ioctl_ops = {
+	.vidioc_querycap = xm2msc_querycap,
+
+	.vidioc_enum_fmt_vid_cap = xm2msc_enum_fmt_vid_cap,
+	.vidioc_g_fmt_vid_cap_mplane = xm2msc_g_fmt_vid_cap,
+	.vidioc_try_fmt_vid_cap_mplane = xm2msc_try_fmt_vid_cap,
+	.vidioc_s_fmt_vid_cap_mplane = xm2msc_s_fmt_vid_cap,
+
+	.vidioc_enum_fmt_vid_out = xm2msc_enum_fmt_vid_out,
+	.vidioc_g_fmt_vid_out_mplane = xm2msc_g_fmt_vid_out,
+	.vidioc_try_fmt_vid_out_mplane = xm2msc_try_fmt_vid_out,
+	.vidioc_s_fmt_vid_out_mplane = xm2msc_s_fmt_vid_out,
+
+	.vidioc_reqbufs = xm2msc_reqbufs,
+	.vidioc_querybuf = xm2msc_querybuf,
+	.vidioc_expbuf = xm2msc_expbuf,
+	.vidioc_create_bufs = xm2msc_createbufs,
+
+	.vidioc_qbuf = xm2msc_qbuf,
+	.vidioc_dqbuf = xm2msc_dqbuf,
+
+	.vidioc_streamon = xm2msc_streamon,
+	.vidioc_streamoff = xm2msc_streamoff,
+};
+
+static int xm2msc_set_q_data(struct xm2msc_chan_ctx *chan_ctx,
+			     const struct xm2msc_fmt *fmt,
+			     enum v4l2_buf_type type)
+{
+	struct xm2msc_q_data *q_data;
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+
+	q_data = get_q_data(chan_ctx, type);
+
+	if (!q_data)
+		return -EINVAL;
+
+	q_data->fmt = fmt;
+	q_data->width = xm2msc->max_wd;
+	q_data->height = xm2msc->max_ht;
+	q_data->field = V4L2_FIELD_NONE;
+	q_data->nbuffs = q_data->fmt->num_buffs;
+
+	q_data->stride = xm2msc_cal_stride(q_data->width,
+				q_data->fmt->xm2msc_fmt,
+				xm2msc->ppc);
+
+	xm2msc_cal_imagesize(chan_ctx, q_data, type);
+
+	return 0;
+}
+
+static int xm2msc_set_chan_parm(struct xm2msc_chan_ctx *chan_ctx)
+{
+	int ret = 0;
+	unsigned int i;
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+
+	chan_ctx->output_stride_align = 1;
+	chan_ctx->output_height_align = 1;
+	chan_ctx->capture_stride_align = 1;
+	chan_ctx->capture_height_align = 1;
+
+	for (i = 0; i < ARRAY_SIZE(formats); i++) {
+		if (xm2msc_chk_fmt(xm2msc, i))
+			break;
+	}
+
+	/* No supported format */
+	if (i == ARRAY_SIZE(formats)) {
+		dev_err(xm2msc->dev, "no supported format found\n");
+		return -EINVAL;
+	}
+
+	ret = xm2msc_set_q_data(chan_ctx, &formats[i],
+				V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE);
+	if (ret)
+		return ret;
+
+	return xm2msc_set_q_data(chan_ctx, &formats[i],
+				 V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE);
+}
+
+static int xm2msc_open(struct file *file)
+{
+	struct xm2m_msc_dev *xm2msc = video_drvdata(file);
+	struct xm2msc_chan_ctx *chan_ctx = NULL;
+	u32 minor, chan;
+	int ret;
+
+	if (mutex_lock_interruptible(&xm2msc->dev_mutex))
+		return -ERESTARTSYS;
+
+	minor = iminor(file_inode(file));
+
+	for (chan = 0; chan < xm2msc->max_chan; chan++) {
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+
+		if ((chan_ctx->status & CHAN_ATTACHED) &&
+		    chan_ctx->minor == minor)
+			break;
+	}
+
+	if (chan == xm2msc->max_chan) {
+		v4l2_err(&xm2msc->v4l2_dev,
+			 "%s Chan not found with minor = %d\n",
+			 __func__, minor);
+		ret = -EBADF;
+		goto unlock;
+	}
+
+	/* Already opened, do not allow same channel
+	 * to be open more then once
+	 */
+	if (chan_ctx->status & CHAN_OPENED) {
+		v4l2_warn(&xm2msc->v4l2_dev,
+			  "%s Chan already opened for minor = %d\n",
+			  __func__, minor);
+		ret = -EBUSY;
+		goto unlock;
+	}
+
+	v4l2_fh_init(&chan_ctx->fh, &chan_ctx->vfd);
+	file->private_data = &chan_ctx->fh;
+	v4l2_fh_add(&chan_ctx->fh);
+
+	chan_ctx->m2m_ctx = v4l2_m2m_ctx_init(chan_ctx->m2m_dev,
+					      chan_ctx, &queue_init);
+	if (IS_ERR(chan_ctx->m2m_ctx)) {
+		ret = PTR_ERR(chan_ctx->m2m_ctx);
+		v4l2_err(&xm2msc->v4l2_dev,
+			 "%s Chan M2M CTX not creted for minor %d\n",
+			 __func__, minor);
+		goto error_m2m;
+	}
+
+	chan_ctx->fh.m2m_ctx = chan_ctx->m2m_ctx;
+	chan_ctx->status |= CHAN_OPENED;
+	chan_ctx->xm2msc_dev = xm2msc;
+	chan_ctx->frames = 0;
+
+	xm2msc_set_chan(chan_ctx, true);
+
+	v4l2_info(&xm2msc->v4l2_dev, "Channel %d instance created\n", chan);
+
+	mutex_unlock(&xm2msc->dev_mutex);
+	xm2msc_pr_chanctx(chan_ctx, __func__);
+	xm2msc_pr_status(xm2msc, __func__);
+	return 0;
+
+error_m2m:
+	v4l2_fh_del(&chan_ctx->fh);
+	v4l2_fh_exit(&chan_ctx->fh);
+unlock:
+	mutex_unlock(&xm2msc->dev_mutex);
+	xm2msc_pr_chanctx(chan_ctx, __func__);
+	xm2msc_pr_status(xm2msc, __func__);
+	return ret;
+}
+
+static int xm2msc_release(struct file *file)
+{
+	struct xm2m_msc_dev *xm2msc = video_drvdata(file);
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(file->private_data);
+
+	if (mutex_lock_interruptible(&xm2msc->dev_mutex))
+		return -ERESTARTSYS;
+
+	v4l2_m2m_ctx_release(chan_ctx->m2m_ctx);
+	v4l2_fh_del(&chan_ctx->fh);
+	v4l2_fh_exit(&chan_ctx->fh);
+	chan_ctx->status &= ~CHAN_OPENED;
+	xm2msc_set_chan(chan_ctx, false);
+
+	v4l2_info(&xm2msc->v4l2_dev, "Channel %d instance released\n",
+		  chan_ctx->num);
+
+	mutex_unlock(&xm2msc->dev_mutex);
+	return 0;
+}
+
+static unsigned int xm2msc_poll(struct file *file,
+				struct poll_table_struct *wait)
+{
+	struct xm2msc_chan_ctx *chan_ctx = fh_to_chanctx(file->private_data);
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	int ret;
+
+	mutex_lock(&xm2msc->dev_mutex);
+	ret = v4l2_m2m_poll(file, chan_ctx->m2m_ctx, wait);
+	mutex_unlock(&xm2msc->dev_mutex);
+
+	return ret;
+}
+
+static int xm2msc_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	struct xm2msc_chan_ctx *chan_ctx = file->private_data;
+	struct xm2m_msc_dev *xm2msc = chan_ctx->xm2msc_dev;
+	int ret;
+
+	mutex_lock(&xm2msc->dev_mutex);
+	ret = v4l2_m2m_mmap(file, chan_ctx->m2m_ctx, vma);
+
+	mutex_unlock(&xm2msc->dev_mutex);
+	return ret;
+}
+
+static const struct v4l2_file_operations xm2msc_fops = {
+	.owner = THIS_MODULE,
+	.open = xm2msc_open,
+	.release = xm2msc_release,
+	.poll = xm2msc_poll,
+	.unlocked_ioctl = video_ioctl2,
+	.mmap = xm2msc_mmap,
+};
+
+static const struct video_device xm2msc_videodev = {
+	.name = XM2MSC_DRIVER_NAME,
+	.fops = &xm2msc_fops,
+	.ioctl_ops = &xm2msc_ioctl_ops,
+	.minor = -1,
+	.release = video_device_release_empty,
+	.vfl_dir = VFL_DIR_M2M,
+};
+
+static const struct v4l2_m2m_ops xm2msc_m2m_ops = {
+	.device_run = xm2msc_device_run,
+	.job_ready = xm2msc_job_ready,
+	.job_abort = xm2msc_job_abort,
+};
+
+static int xm2msc_parse_of(struct platform_device *pdev,
+			   struct xm2m_msc_dev *xm2msc)
+{
+	struct resource *res;
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	int hw_vid_fmt_cnt;
+	const char *vid_fmts[ARRAY_SIZE(formats)];
+	int ret;
+	u32 i, j;
+
+	xm2msc->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(xm2msc->clk)) {
+		ret = PTR_ERR(xm2msc->clk);
+		dev_err(dev, "failed to get clk (%d)\n", ret);
+		return ret;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xm2msc->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR((__force void *)xm2msc->regs))
+		return PTR_ERR((__force const void *)xm2msc->regs);
+
+	dev_dbg(dev, "IO Mem %pa mapped at %p\n", &res->start, xm2msc->regs);
+
+	ret = of_property_read_u32(node, "xlnx,max-chan",
+				   &xm2msc->max_chan);
+	if (ret < 0)
+		return ret;
+
+	if (xm2msc->max_chan < XM2MSC_MIN_CHAN ||
+	    xm2msc->max_chan > XM2MSC_MAX_CHAN) {
+		dev_err(dev,
+			"Invalid maximum scaler channels : %d",
+			xm2msc->max_chan);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-width",
+				   &xm2msc->max_wd);
+	if (ret < 0) {
+		dev_err(dev,
+			"missing xlnx,max-width prop\n");
+		return ret;
+	}
+
+	if (xm2msc->max_wd < XM2MSC_MIN_WIDTH ||
+	    xm2msc->max_wd > XM2MSC_MAX_WIDTH) {
+		dev_err(dev, "Invalid width : %d",
+			xm2msc->max_wd);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-height",
+				   &xm2msc->max_ht);
+	if (ret < 0) {
+		dev_err(dev, "missing xlnx,max-height prop\n");
+		return ret;
+	}
+
+	if (xm2msc->max_ht < XM2MSC_MIN_HEIGHT ||
+	    xm2msc->max_ht > XM2MSC_MAX_HEIGHT) {
+		dev_err(dev, "Invalid height : %d",
+			xm2msc->max_ht);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,dma-addr-width",
+				   &xm2msc->dma_addr_size);
+	if (ret || (xm2msc->dma_addr_size != 32 &&
+		    xm2msc->dma_addr_size != 64)) {
+		dev_err(dev, "missing/invalid addr width dts prop\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u8(node, "xlnx,pixels-per-clock",
+				  &xm2msc->ppc);
+	if (ret || (xm2msc->ppc != 1 && xm2msc->ppc != 2 && xm2msc->ppc != 4)) {
+		dev_err(dev, "missing or invalid pixels per clock dts prop\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-taps",
+				   &xm2msc->taps);
+	if (ret || (xm2msc->taps != XSCALER_TAPS_6 &&
+		    xm2msc->taps != XSCALER_TAPS_8 &&
+		    xm2msc->taps != XSCALER_TAPS_10 &&
+		    xm2msc->taps != XSCALER_TAPS_12)) {
+		dev_err(dev, "missing/invalid taps in dts prop\n");
+		return -EINVAL;
+	}
+
+	xm2msc->irq = irq_of_parse_and_map(node, 0);
+	if (xm2msc->irq < 0) {
+		dev_err(dev, "Unable to get IRQ");
+		return xm2msc->irq;
+	}
+
+	dev_dbg(dev, "Max Channel Supported = %d\n", xm2msc->max_chan);
+	dev_dbg(dev, "DMA Addr width Supported = %d\n", xm2msc->dma_addr_size);
+	dev_dbg(dev, "Max col/row Supported = (%d) / (%d)\n",
+		xm2msc->max_wd, xm2msc->max_ht);
+	dev_dbg(dev, "taps Supported = %d\n", xm2msc->taps);
+	/* read supported video formats and update internal table */
+	hw_vid_fmt_cnt = of_property_count_strings(node, "xlnx,vid-formats");
+
+	ret = of_property_read_string_array(node, "xlnx,vid-formats",
+					    vid_fmts, hw_vid_fmt_cnt);
+	if (ret < 0) {
+		dev_err(dev,
+			"Missing or invalid xlnx,vid-formats dts prop\n");
+		return ret;
+	}
+
+	dev_dbg(dev, "Supported format = ");
+	for (i = 0; i < hw_vid_fmt_cnt; i++) {
+		const char *vid_fmt_name = vid_fmts[i];
+
+		for (j = 0; j < ARRAY_SIZE(formats); j++) {
+			const char *dts_name = formats[j].name;
+
+			if (strcmp(vid_fmt_name, dts_name))
+				continue;
+			dev_dbg(dev, "%s ", dts_name);
+
+			xm2msc_set_fmt(xm2msc, j);
+		}
+	}
+	dev_dbg(dev, "\n");
+	xm2msc->rst_gpio = devm_gpiod_get(dev, "reset",
+					  GPIOD_OUT_HIGH);
+	if (IS_ERR(xm2msc->rst_gpio)) {
+		ret = PTR_ERR(xm2msc->rst_gpio);
+		if (ret == -EPROBE_DEFER)
+			dev_info(dev,
+				 "Probe deferred due to GPIO reset defer\n");
+		else
+			dev_err(dev,
+				"Unable to locate reset property in dt\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void xm2msc_unreg_video_n_m2m(struct xm2m_msc_dev *xm2msc)
+{
+	struct xm2msc_chan_ctx *chan_ctx;
+	unsigned int chan;
+
+	for (chan = 0; chan < xm2msc->max_chan; chan++) {
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+		if (!(chan_ctx->status & CHAN_ATTACHED))
+			break;	/*We register video sequentially */
+		video_unregister_device(&chan_ctx->vfd);
+		chan_ctx->status &= ~CHAN_ATTACHED;
+
+		if (!IS_ERR(chan_ctx->m2m_dev))
+			v4l2_m2m_release(chan_ctx->m2m_dev);
+	}
+}
+
+static int xm2m_msc_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct xm2m_msc_dev *xm2msc;
+	struct xm2msc_chan_ctx *chan_ctx;
+	struct video_device *vfd;
+	unsigned int chan;
+
+	xm2msc = devm_kzalloc(&pdev->dev, sizeof(*xm2msc), GFP_KERNEL);
+	if (!xm2msc)
+		return -ENOMEM;
+
+	ret = xm2msc_parse_of(pdev, xm2msc);
+	if (ret < 0)
+		return ret;
+
+	xm2msc->dev = &pdev->dev;
+
+	ret = clk_prepare_enable(xm2msc->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable clk (%d)\n", ret);
+		return ret;
+	}
+
+	xm2msc_reset(xm2msc);
+
+	spin_lock_init(&xm2msc->lock);
+
+	ret = v4l2_device_register(&pdev->dev, &xm2msc->v4l2_dev);
+	if (ret)
+		goto reg_dev_err;
+
+	for (chan = 0; chan < xm2msc->max_chan; chan++) {
+		chan_ctx = &xm2msc->xm2msc_chan[chan];
+
+		vfd = &chan_ctx->vfd;
+		*vfd = xm2msc_videodev;
+		vfd->lock = &xm2msc->dev_mutex;
+		vfd->v4l2_dev = &xm2msc->v4l2_dev;
+		vfd->device_caps = V4L2_CAP_VIDEO_M2M_MPLANE |
+				   V4L2_CAP_STREAMING;
+
+		ret = video_register_device(vfd, VFL_TYPE_VIDEO, chan);
+		if (ret) {
+			v4l2_err(&xm2msc->v4l2_dev,
+				 "Failed to register video dev for chan %d\n",
+				 chan);
+			goto unreg_dev;
+		}
+
+		chan_ctx->status = CHAN_ATTACHED;
+
+		video_set_drvdata(vfd, xm2msc);
+		snprintf(vfd->name, sizeof(vfd->name),
+			 "%s", xm2msc_videodev.name);
+		v4l2_info(&xm2msc->v4l2_dev,
+			  " Device registered as /dev/video%d\n", vfd->num);
+
+		dev_dbg(xm2msc->dev, "%s Device registered as /dev/video%d\n",
+			__func__, vfd->num);
+
+		chan_ctx->m2m_dev = v4l2_m2m_init(&xm2msc_m2m_ops);
+		if (IS_ERR(chan_ctx->m2m_dev)) {
+			v4l2_err(&xm2msc->v4l2_dev,
+				 "Failed to init mem2mem device for chan %d\n",
+				 chan);
+			ret = PTR_ERR(chan_ctx->m2m_dev);
+			goto unreg_dev;
+		}
+		chan_ctx->xm2msc_dev = xm2msc;
+		chan_ctx->regs = xm2msc->regs + XM2MSC_CHAN_REGS_START(chan);
+		if (chan > 4) /* TODO: To be fixed in HW */
+			chan_ctx->regs += XM2MSC_RESERVED_AREA;
+		chan_ctx->num = chan;
+		chan_ctx->minor = vfd->minor;
+
+		/* Set channel parameters to default values */
+		ret = xm2msc_set_chan_parm(chan_ctx);
+		if (ret)
+			goto unreg_dev;
+
+		xm2msc_pr_chanctx(chan_ctx, __func__);
+	}
+
+	mutex_init(&xm2msc->dev_mutex);
+	mutex_init(&xm2msc->mutex);
+	init_waitqueue_head(&xm2msc->isr_finished);
+
+	ret = devm_request_irq(&pdev->dev, xm2msc->irq,
+			       xm2msc_isr, IRQF_SHARED,
+			       XM2MSC_DRIVER_NAME, xm2msc);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Unable to register IRQ\n");
+		goto unreg_dev;
+	}
+
+	platform_set_drvdata(pdev, xm2msc);
+
+	return 0;
+
+unreg_dev:
+	xm2msc_unreg_video_n_m2m(xm2msc);
+	v4l2_device_unregister(&xm2msc->v4l2_dev);
+reg_dev_err:
+	clk_disable_unprepare(xm2msc->clk);
+	return ret;
+}
+
+static int xm2m_msc_remove(struct platform_device *pdev)
+{
+	struct xm2m_msc_dev *xm2msc = platform_get_drvdata(pdev);
+
+	xm2msc_unreg_video_n_m2m(xm2msc);
+	v4l2_device_unregister(&xm2msc->v4l2_dev);
+	clk_disable_unprepare(xm2msc->clk);
+	return 0;
+}
+
+static const struct of_device_id xm2m_msc_of_id_table[] = {
+	{.compatible = "xlnx,v-multi-scaler-v1.0"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, xm2m_msc_of_id_table);
+
+static struct platform_driver xm2m_msc_driver = {
+	.driver = {
+		.name = "xilinx-multiscaler",
+		.of_match_table = xm2m_msc_of_id_table,
+	},
+	.probe = xm2m_msc_probe,
+	.remove = xm2m_msc_remove,
+};
+
+module_platform_driver(xm2m_msc_driver);
+
+MODULE_DESCRIPTION("Xilinx M2M Multi-Scaler Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("xlnx_m2m_multiscaler_dev");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-remapper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-remapper.c
@@ -0,0 +1,566 @@
+/*
+ * Xilinx Video Remapper
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XREMAP_MIN_WIDTH			1
+#define XREMAP_DEF_WIDTH			1920
+#define XREMAP_MAX_WIDTH			65535
+#define XREMAP_MIN_HEIGHT			1
+#define XREMAP_DEF_HEIGHT			1080
+#define XREMAP_MAX_HEIGHT			65535
+
+#define XREMAP_PAD_SINK				0
+#define XREMAP_PAD_SOURCE			1
+
+/**
+ * struct xremap_mapping_output - Output format description
+ * @code: media bus pixel core after remapping
+ * @num_components: number of pixel components after remapping
+ * @component_maps: configuration array corresponding to this output
+ */
+struct xremap_mapping_output {
+	u32 code;
+	unsigned int num_components;
+	unsigned int component_maps[4];
+};
+
+/**
+ * struct xremap_mapping - Input-output remapping description
+ * @code: media bus pixel code before remapping
+ * @width: video bus width in bits
+ * @num_components: number of pixel components before remapping
+ * @outputs: array of possible output formats
+ */
+struct xremap_mapping {
+	u32 code;
+	unsigned int width;
+	unsigned int num_components;
+	const struct xremap_mapping_output *outputs;
+};
+
+/**
+ * struct xremap_device - Xilinx Test Pattern Generator device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @formats: V4L2 media bus formats at the sink and source pads
+ * @config: device configuration parsed from its DT node
+ * @config.width: video bus width in bits
+ * @config.num_s_components: number of pixel components at the input
+ * @config.num_m_components: number of pixel components at the output
+ * @config.component_maps: component remapping configuration
+ * @default_mapping: Default mapping compatible with the configuration
+ * @default_output: Default output format for the default mapping
+ */
+struct xremap_device {
+	struct xvip_device xvip;
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt formats[2];
+
+	struct {
+		unsigned int width;
+		unsigned int num_s_components;
+		unsigned int num_m_components;
+		unsigned int component_maps[4];
+	} config;
+
+	const struct xremap_mapping *default_mapping;
+	const struct xremap_mapping_output *default_output;
+};
+
+static inline struct xremap_device *to_remap(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xremap_device, xvip.subdev);
+}
+
+/* -----------------------------------------------------------------------------
+ * Mappings
+ */
+
+static const struct xremap_mapping xremap_mappings[] = {
+	{
+		.code = MEDIA_BUS_FMT_RBG888_1X24,
+		.width = 8,
+		.num_components = 3,
+		.outputs = (const struct xremap_mapping_output[]) {
+			{ MEDIA_BUS_FMT_RGB888_1X32_PADHI, 4, { 1, 0, 2, 4 } },
+			{ },
+		},
+	},
+};
+
+static const struct xremap_mapping_output *
+xremap_match_mapping(struct xremap_device *xremap,
+		     const struct xremap_mapping *mapping)
+{
+	const struct xremap_mapping_output *output;
+
+	if (mapping->width != xremap->config.width ||
+	    mapping->num_components != xremap->config.num_s_components)
+		return NULL;
+
+	for (output = mapping->outputs; output->code; ++output) {
+		unsigned int i;
+
+		if (output->num_components != xremap->config.num_m_components)
+			continue;
+
+		for (i = 0; i < output->num_components; ++i) {
+			if (output->component_maps[i] !=
+			    xremap->config.component_maps[i])
+				break;
+		}
+
+		if (i == output->num_components)
+			return output;
+	}
+
+	return NULL;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+static int xremap_enum_mbus_code(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct xremap_device *xremap = to_remap(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	if (code->pad == XREMAP_PAD_SINK) {
+		const struct xremap_mapping *mapping = NULL;
+		unsigned int index = code->index + 1;
+		unsigned int i;
+
+		/* Iterate through the mappings and skip the ones that don't
+		 * match the remapper configuration until we reach the requested
+		 * index.
+		 */
+		for (i = 0; i < ARRAY_SIZE(xremap_mappings) && index; ++i) {
+			mapping = &xremap_mappings[i];
+
+			if (xremap_match_mapping(xremap, mapping))
+				index--;
+		}
+
+		/* If the index was larger than the number of supported mappings
+		 * return -EINVAL.
+		 */
+		if (index > 0)
+			return -EINVAL;
+
+		code->code = mapping->code;
+	} else {
+		if (code->index)
+			return -EINVAL;
+
+		format = v4l2_subdev_get_try_format(subdev, sd_state, code->pad);
+		code->code = format->code;
+	}
+
+	return 0;
+}
+
+static int xremap_enum_frame_size(struct v4l2_subdev *subdev,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	format = v4l2_subdev_get_try_format(subdev, sd_state, fse->pad);
+
+	if (fse->index || fse->code != format->code)
+		return -EINVAL;
+
+	if (fse->pad == XREMAP_PAD_SINK) {
+		/* The remapper doesn't restrict the size on the sink pad. */
+		fse->min_width = XREMAP_MIN_WIDTH;
+		fse->max_width = XREMAP_MAX_WIDTH;
+		fse->min_height = XREMAP_MIN_HEIGHT;
+		fse->max_height = XREMAP_MAX_HEIGHT;
+	} else {
+		/* The size on the source pad are fixed and always identical to
+		 * the size on the sink pad.
+		 */
+		fse->min_width = format->width;
+		fse->max_width = format->width;
+		fse->min_height = format->height;
+		fse->max_height = format->height;
+	}
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+xremap_get_pad_format(struct xremap_device *xremap,
+		      struct v4l2_subdev_state *sd_state,
+		      unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xremap->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xremap->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xremap_get_format(struct v4l2_subdev *subdev,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct xremap_device *xremap = to_remap(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = xremap_get_pad_format(xremap, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xremap_set_format(struct v4l2_subdev *subdev,
+			     struct v4l2_subdev_state *sd_state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct xremap_device *xremap = to_remap(subdev);
+	const struct xremap_mapping_output *output = NULL;
+	const struct xremap_mapping *mapping;
+	struct v4l2_mbus_framefmt *format;
+	unsigned int i;
+
+	format = xremap_get_pad_format(xremap, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	if (fmt->pad == XREMAP_PAD_SOURCE) {
+		fmt->format = *format;
+		return 0;
+	}
+
+	/* Find the mapping. If the requested format has no mapping, use the
+	 * default.
+	 */
+	for (i = 0; i < ARRAY_SIZE(xremap_mappings); ++i) {
+		mapping = &xremap_mappings[i];
+		if (mapping->code != fmt->format.code)
+			continue;
+
+		output = xremap_match_mapping(xremap, mapping);
+		if (output)
+			break;
+	}
+
+	if (!output) {
+		mapping = xremap->default_mapping;
+		output = xremap->default_output;
+	}
+
+	format->code = mapping->code;
+	format->width = clamp_t(unsigned int, fmt->format.width,
+				XREMAP_MIN_WIDTH, XREMAP_MAX_WIDTH);
+	format->height = clamp_t(unsigned int, fmt->format.height,
+				 XREMAP_MIN_HEIGHT, XREMAP_MAX_HEIGHT);
+	format->field = V4L2_FIELD_NONE;
+	format->colorspace = V4L2_COLORSPACE_SRGB;
+
+	fmt->format = *format;
+
+	/* Propagate the format to the source pad. */
+	format = xremap_get_pad_format(xremap, sd_state, XREMAP_PAD_SOURCE,
+				       fmt->which);
+	if (!format)
+		return -EINVAL;
+	*format = fmt->format;
+	format->code = output->code;
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Operations
+ */
+
+/*
+ * xremap_init_formats - Initialize formats on all pads
+ * @subdev: remapper V4L2 subdevice
+ * @fh: V4L2 subdev file handle
+ *
+ * Initialize all pad formats with default values. If fh is not NULL, try
+ * formats are initialized on the file handle. Otherwise active formats are
+ * initialized on the device.
+ */
+static void xremap_init_formats(struct v4l2_subdev *subdev,
+				struct v4l2_subdev_fh *fh)
+{
+	struct xremap_device *xremap = to_remap(subdev);
+	struct v4l2_subdev_format format;
+
+	memset(&format, 0, sizeof(format));
+
+	format.pad = XREMAP_PAD_SINK;
+	format.which = fh ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
+	format.format.code = xremap->default_mapping->code;
+	format.format.width = XREMAP_DEF_WIDTH;
+	format.format.height = XREMAP_DEF_HEIGHT;
+
+	xremap_set_format(subdev, fh ? fh->state : NULL, &format);
+}
+
+static int xremap_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	xremap_init_formats(subdev, fh);
+
+	return 0;
+}
+
+static int xremap_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_core_ops xremap_core_ops = {
+};
+
+static struct v4l2_subdev_video_ops xremap_video_ops = {
+};
+
+static struct v4l2_subdev_pad_ops xremap_pad_ops = {
+	.enum_mbus_code = xremap_enum_mbus_code,
+	.enum_frame_size = xremap_enum_frame_size,
+	.get_fmt = xremap_get_format,
+	.set_fmt = xremap_set_format,
+};
+
+static struct v4l2_subdev_ops xremap_ops = {
+	.core   = &xremap_core_ops,
+	.video  = &xremap_video_ops,
+	.pad    = &xremap_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xremap_internal_ops = {
+	.open = xremap_open,
+	.close = xremap_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xremap_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int xremap_parse_of(struct xremap_device *xremap)
+{
+	struct device_node *node = xremap->xvip.dev->of_node;
+	unsigned int i;
+	int ret;
+
+	/* Parse the DT properties. */
+	ret = of_property_read_u32(node, "xlnx,video-width",
+				   &xremap->config.width);
+	if (ret < 0) {
+		dev_dbg(xremap->xvip.dev, "unable to parse %s property\n",
+			"xlnx,video-width");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "#xlnx,s-components",
+				   &xremap->config.num_s_components);
+	if (ret < 0) {
+		dev_dbg(xremap->xvip.dev, "unable to parse %s property\n",
+			"#xlnx,s-components");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "#xlnx,m-components",
+				   &xremap->config.num_m_components);
+	if (ret < 0) {
+		dev_dbg(xremap->xvip.dev, "unable to parse %s property\n",
+			"#xlnx,m-components");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32_array(node, "xlnx,component-maps",
+					 xremap->config.component_maps,
+					 xremap->config.num_m_components);
+	if (ret < 0) {
+		dev_dbg(xremap->xvip.dev, "unable to parse %s property\n",
+			"xlnx,component-maps");
+		return -EINVAL;
+	}
+
+	/* Validate the parsed values. */
+	if (xremap->config.num_s_components > 4 ||
+	    xremap->config.num_m_components > 4) {
+		dev_dbg(xremap->xvip.dev,
+			"invalid number of components (s %u m %u)\n",
+			xremap->config.num_s_components,
+			xremap->config.num_m_components);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < xremap->config.num_m_components; ++i) {
+		if (xremap->config.component_maps[i] > 4) {
+			dev_dbg(xremap->xvip.dev, "invalid map %u @%u\n",
+				xremap->config.component_maps[i], i);
+			return -EINVAL;
+		}
+	}
+
+	/* Find the first mapping that matches the remapper configuration and
+	 * store it as the default mapping.
+	 */
+	for (i = 0; i < ARRAY_SIZE(xremap_mappings); ++i) {
+		const struct xremap_mapping_output *output;
+		const struct xremap_mapping *mapping;
+
+		mapping = &xremap_mappings[i];
+		output = xremap_match_mapping(xremap, mapping);
+
+		if (output) {
+			xremap->default_mapping = mapping;
+			xremap->default_output = output;
+			return 0;
+		}
+	}
+
+	dev_err(xremap->xvip.dev,
+		"No format compatible with device configuration\n");
+
+	return -EINVAL;
+}
+
+static int xremap_probe(struct platform_device *pdev)
+{
+	struct xremap_device *xremap;
+	struct v4l2_subdev *subdev;
+	int ret;
+
+	xremap = devm_kzalloc(&pdev->dev, sizeof(*xremap), GFP_KERNEL);
+	if (!xremap)
+		return -ENOMEM;
+
+	xremap->xvip.dev = &pdev->dev;
+
+	ret = xremap_parse_of(xremap);
+	if (ret < 0)
+		return ret;
+
+	xremap->xvip.clk = devm_clk_get(xremap->xvip.dev, NULL);
+	if (IS_ERR(xremap->xvip.clk))
+		return PTR_ERR(xremap->xvip.clk);
+
+	ret = clk_prepare_enable(xremap->xvip.clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable clk (%d)\n", ret);
+		return ret;
+	}
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xremap->xvip.subdev;
+	v4l2_subdev_init(subdev, &xremap_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xremap_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xremap);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	xremap_init_formats(subdev, NULL);
+
+	xremap->pads[XREMAP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xremap->pads[XREMAP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xremap_media_ops;
+	ret = media_entity_pads_init(&subdev->entity, 2, xremap->pads);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xremap);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	dev_info(&pdev->dev, "device registered\n");
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+	clk_disable_unprepare(xremap->xvip.clk);
+	return ret;
+}
+
+static int xremap_remove(struct platform_device *pdev)
+{
+	struct xremap_device *xremap = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xremap->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+
+	clk_disable_unprepare(xremap->xvip.clk);
+
+	return 0;
+}
+
+static const struct of_device_id xremap_of_id_table[] = {
+	{ .compatible = "xlnx,v-remapper" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xremap_of_id_table);
+
+static struct platform_driver xremap_driver = {
+	.driver = {
+		.name = "xilinx-remapper",
+		.of_match_table = xremap_of_id_table,
+	},
+	.probe = xremap_probe,
+	.remove = xremap_remove,
+};
+
+module_platform_driver(xremap_driver);
+
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_DESCRIPTION("Xilinx Video Remapper Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-rgb2yuv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-rgb2yuv.c
@@ -0,0 +1,581 @@
+/*
+ * Xilinx RGB to YUV Convertor
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/xilinx-v4l2-controls.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XRGB2YUV_YMAX					0x100
+#define XRGB2YUV_YMIN					0x104
+#define XRGB2YUV_CBMAX					0x108
+#define XRGB2YUV_CBMIN					0x10c
+#define XRGB2YUV_CRMAX					0x110
+#define XRGB2YUV_CRMIN					0x114
+#define XRGB2YUV_YOFFSET				0x118
+#define XRGB2YUV_CBOFFSET				0x11c
+#define XRGB2YUV_CROFFSET				0x120
+#define XRGB2YUV_ACOEF					0x124
+#define XRGB2YUV_BCOEF					0x128
+#define XRGB2YUV_CCOEF					0x12c
+#define XRGB2YUV_DCOEF					0x130
+
+/**
+ * struct xrgb2yuv_device - Xilinx RGB2YUV device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @formats: V4L2 media bus formats at the sink and source pads
+ * @default_formats: default V4L2 media bus formats
+ * @vip_formats: Xilinx Video IP formats
+ * @ctrl_handler: control handler
+ */
+struct xrgb2yuv_device {
+	struct xvip_device xvip;
+
+	struct media_pad pads[2];
+
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_formats[2];
+
+	struct v4l2_ctrl_handler ctrl_handler;
+};
+
+static inline struct xrgb2yuv_device *to_rgb2yuv(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xrgb2yuv_device, xvip.subdev);
+}
+
+/*
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xrgb2yuv_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xrgb2yuv_device *xrgb2yuv = to_rgb2yuv(subdev);
+
+	if (!enable) {
+		xvip_stop(&xrgb2yuv->xvip);
+		return 0;
+	}
+
+	xvip_set_frame_size(&xrgb2yuv->xvip, &xrgb2yuv->formats[XVIP_PAD_SINK]);
+
+	xvip_start(&xrgb2yuv->xvip);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+__xrgb2yuv_get_pad_format(struct xrgb2yuv_device *xrgb2yuv,
+			  struct v4l2_subdev_state *sd_state,
+			  unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xrgb2yuv->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xrgb2yuv->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xrgb2yuv_get_format(struct v4l2_subdev *subdev,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_format *fmt)
+{
+	struct xrgb2yuv_device *xrgb2yuv = to_rgb2yuv(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xrgb2yuv_get_pad_format(xrgb2yuv, sd_state, fmt->pad,
+					   fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xrgb2yuv_set_format(struct v4l2_subdev *subdev,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_format *fmt)
+{
+	struct xrgb2yuv_device *xrgb2yuv = to_rgb2yuv(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xrgb2yuv_get_pad_format(xrgb2yuv, sd_state, fmt->pad,
+					   fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		fmt->format = *format;
+		return 0;
+	}
+
+	xvip_set_format_size(format, fmt);
+
+	fmt->format = *format;
+
+	/* Propagate the format to the source pad. */
+	format = __xrgb2yuv_get_pad_format(xrgb2yuv, sd_state, XVIP_PAD_SOURCE,
+					     fmt->which);
+
+	xvip_set_format_size(format, fmt);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Operations
+ */
+
+static int xrgb2yuv_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xrgb2yuv_device *xrgb2yuv = to_rgb2yuv(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xrgb2yuv->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xrgb2yuv->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int xrgb2yuv_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static int xrgb2yuv_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct xrgb2yuv_device *xrgb2yuv =
+		container_of(ctrl->handler, struct xrgb2yuv_device,
+			     ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_RGB2YUV_YMAX:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_YMAX, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_YMIN:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_YMIN, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CBMAX:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CBMAX, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CBMIN:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CBMIN, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CRMAX:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CRMAX, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CRMIN:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CRMIN, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_YOFFSET:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_YOFFSET, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CBOFFSET:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CBOFFSET, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CROFFSET:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CROFFSET, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_ACOEF:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_ACOEF, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_BCOEF:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_BCOEF, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_CCOEF:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_CCOEF, ctrl->val);
+		return 0;
+	case V4L2_CID_XILINX_RGB2YUV_DCOEF:
+		xvip_write(&xrgb2yuv->xvip, XRGB2YUV_DCOEF, ctrl->val);
+		return 0;
+	}
+
+	return -EINVAL;
+}
+
+static const struct v4l2_ctrl_ops xrgb2yuv_ctrl_ops = {
+	.s_ctrl	= xrgb2yuv_s_ctrl,
+};
+
+static struct v4l2_subdev_video_ops xrgb2yuv_video_ops = {
+	.s_stream = xrgb2yuv_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xrgb2yuv_pad_ops = {
+	.enum_mbus_code		= xvip_enum_mbus_code,
+	.enum_frame_size	= xvip_enum_frame_size,
+	.get_fmt		= xrgb2yuv_get_format,
+	.set_fmt		= xrgb2yuv_set_format,
+};
+
+static struct v4l2_subdev_ops xrgb2yuv_ops = {
+	.video  = &xrgb2yuv_video_ops,
+	.pad    = &xrgb2yuv_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xrgb2yuv_internal_ops = {
+	.open	= xrgb2yuv_open,
+	.close	= xrgb2yuv_close,
+};
+
+/*
+ * Control Configs
+ */
+
+static struct v4l2_ctrl_config xrgb2yuv_ctrls[] = {
+	{
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_YMAX,
+		.name	= "RGB to YUV: Maximum Y value",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 16) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_YMIN,
+		.name	= "RGB to YUV: Minimum Y value",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 16) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CBMAX,
+		.name	= "RGB to YUV: Maximum Cb value",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 16) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CBMIN,
+		.name	= "RGB to YUV: Minimum Cb value",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 16) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CRMAX,
+		.name	= "RGB to YUV: Maximum Cr value",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 16) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CRMIN,
+		.name	= "RGB to YUV: Minimum Cr value",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 16) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_YOFFSET,
+		.name	= "RGB to YUV: Luma offset",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CBOFFSET,
+		.name	= "RGB to YUV: Chroma Cb offset",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CROFFSET,
+		.name	= "RGB to YUV: Chroma Cr offset",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_ACOEF,
+		.name	= "RGB to YUV: CA coefficient",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= -((1 << 17) - 1),
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_BCOEF,
+		.name	= "RGB to YUV: CB coefficient",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= -((1 << 17) - 1),
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_CCOEF,
+		.name	= "RGB to YUV: CC coefficient",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= -((1 << 17) - 1),
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	}, {
+		.ops	= &xrgb2yuv_ctrl_ops,
+		.id	= V4L2_CID_XILINX_RGB2YUV_DCOEF,
+		.name	= "RGB to YUV: CD coefficient",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= -((1 << 17) - 1),
+		.max	= (1 << 17) - 1,
+		.step	= 1,
+	},
+};
+
+/*
+ * Media Operations
+ */
+
+static const struct media_entity_operations xrgb2yuv_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/*
+ * Power Management
+ */
+
+static int __maybe_unused xrgb2yuv_pm_suspend(struct device *dev)
+{
+	struct xrgb2yuv_device *xrgb2yuv = dev_get_drvdata(dev);
+
+	xvip_suspend(&xrgb2yuv->xvip);
+
+	return 0;
+}
+
+static int __maybe_unused xrgb2yuv_pm_resume(struct device *dev)
+{
+	struct xrgb2yuv_device *xrgb2yuv = dev_get_drvdata(dev);
+
+	xvip_resume(&xrgb2yuv->xvip);
+
+	return 0;
+}
+
+/*
+ * Platform Device Driver
+ */
+
+static int xrgb2yuv_parse_of(struct xrgb2yuv_device *xrgb2yuv)
+{
+	struct device *dev = xrgb2yuv->xvip.dev;
+	struct device_node *node = xrgb2yuv->xvip.dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id;
+	int ret;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (ports == NULL)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			const struct xvip_video_format *vip_format;
+
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "invalid format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			ret = of_property_read_u32(port, "reg", &port_id);
+			if (ret < 0) {
+				dev_err(dev, "no reg in DT");
+				return ret;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "invalid reg in DT");
+				return -EINVAL;
+			}
+
+			xrgb2yuv->vip_formats[port_id] = vip_format;
+		}
+	}
+
+	return 0;
+}
+
+static int xrgb2yuv_probe(struct platform_device *pdev)
+{
+	struct xrgb2yuv_device *xrgb2yuv;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *default_format;
+	unsigned int i;
+	int ret;
+
+	xrgb2yuv = devm_kzalloc(&pdev->dev, sizeof(*xrgb2yuv), GFP_KERNEL);
+	if (!xrgb2yuv)
+		return -ENOMEM;
+
+	xrgb2yuv->xvip.dev = &pdev->dev;
+
+	ret = xrgb2yuv_parse_of(xrgb2yuv);
+	if (ret < 0)
+		return ret;
+
+	ret = xvip_init_resources(&xrgb2yuv->xvip);
+	if (ret < 0)
+		return ret;
+
+	/* Reset and initialize the core */
+	xvip_reset(&xrgb2yuv->xvip);
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xrgb2yuv->xvip.subdev;
+	v4l2_subdev_init(subdev, &xrgb2yuv_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xrgb2yuv_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xrgb2yuv);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Initialize default and active formats */
+	default_format = &xrgb2yuv->default_formats[XVIP_PAD_SINK];
+	default_format->code = xrgb2yuv->vip_formats[XVIP_PAD_SINK]->code;
+	default_format->field = V4L2_FIELD_NONE;
+	default_format->colorspace = V4L2_COLORSPACE_SRGB;
+	xvip_get_frame_size(&xrgb2yuv->xvip, default_format);
+
+	xrgb2yuv->formats[XVIP_PAD_SINK] = *default_format;
+
+	default_format = &xrgb2yuv->default_formats[XVIP_PAD_SOURCE];
+	*default_format = xrgb2yuv->default_formats[XVIP_PAD_SINK];
+	default_format->code = xrgb2yuv->vip_formats[XVIP_PAD_SOURCE]->code;
+
+	xrgb2yuv->formats[XVIP_PAD_SOURCE] = *default_format;
+
+	xrgb2yuv->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xrgb2yuv->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xrgb2yuv_media_ops;
+	ret = media_entity_pads_init(&subdev->entity, 2, xrgb2yuv->pads);
+	if (ret < 0)
+		goto error;
+
+	v4l2_ctrl_handler_init(&xrgb2yuv->ctrl_handler, 13);
+
+	for (i = 0; i < ARRAY_SIZE(xrgb2yuv_ctrls); i++) {
+		xrgb2yuv_ctrls[i].def = xvip_read(&xrgb2yuv->xvip,
+						  XRGB2YUV_YMAX + i * 4);
+		v4l2_ctrl_new_custom(&xrgb2yuv->ctrl_handler,
+				     &xrgb2yuv_ctrls[i], NULL);
+	}
+
+	if (xrgb2yuv->ctrl_handler.error) {
+		dev_err(&pdev->dev, "failed to add controls\n");
+		ret = xrgb2yuv->ctrl_handler.error;
+		goto error;
+	}
+	subdev->ctrl_handler = &xrgb2yuv->ctrl_handler;
+
+	platform_set_drvdata(pdev, xrgb2yuv);
+
+	xvip_print_version(&xrgb2yuv->xvip);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	v4l2_ctrl_handler_free(&xrgb2yuv->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xrgb2yuv->xvip);
+	return ret;
+}
+
+static int xrgb2yuv_remove(struct platform_device *pdev)
+{
+	struct xrgb2yuv_device *xrgb2yuv = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xrgb2yuv->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&xrgb2yuv->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+
+	xvip_cleanup_resources(&xrgb2yuv->xvip);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(xrgb2yuv_pm_ops, xrgb2yuv_pm_suspend,
+			 xrgb2yuv_pm_resume);
+
+static const struct of_device_id xrgb2yuv_of_id_table[] = {
+	{ .compatible = "xlnx,v-rgb2yuv-7.1" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xrgb2yuv_of_id_table);
+
+static struct platform_driver xrgb2yuv_driver = {
+	.driver			= {
+		.name		= "xilinx-rgb2yuv",
+		.pm		= &xrgb2yuv_pm_ops,
+		.of_match_table	= xrgb2yuv_of_id_table,
+	},
+	.probe			= xrgb2yuv_probe,
+	.remove			= xrgb2yuv_remove,
+};
+
+module_platform_driver(xrgb2yuv_driver);
+
+MODULE_DESCRIPTION("Xilinx RGB to YUV Converter Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-scaler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-scaler.c
@@ -0,0 +1,751 @@
+/*
+ * Xilinx Scaler
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/fixp-arith.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XSCALER_MIN_WIDTH			32
+#define XSCALER_MAX_WIDTH			4096
+#define XSCALER_MIN_HEIGHT			32
+#define XSCALER_MAX_HEIGHT			4096
+
+#define XSCALER_HSF				0x0100
+#define XSCALER_VSF				0x0104
+#define XSCALER_SF_SHIFT			20
+#define XSCALER_SF_MASK				0xffffff
+#define XSCALER_SOURCE_SIZE			0x0108
+#define XSCALER_SIZE_HORZ_SHIFT			0
+#define XSCALER_SIZE_VERT_SHIFT			16
+#define XSCALER_SIZE_MASK			0xfff
+#define XSCALER_HAPERTURE			0x010c
+#define XSCALER_VAPERTURE			0x0110
+#define XSCALER_APERTURE_START_SHIFT		0
+#define XSCALER_APERTURE_END_SHIFT		16
+#define XSCALER_OUTPUT_SIZE			0x0114
+#define XSCALER_COEF_DATA_IN			0x0134
+#define XSCALER_COEF_DATA_IN_SHIFT		16
+
+/* Fixed point operations */
+#define FRAC_N	8
+
+static inline s16 fixp_new(s16 a)
+{
+	return a << FRAC_N;
+}
+
+static inline s16 fixp_mult(s16 a, s16 b)
+{
+	return ((s32)(a * b)) >> FRAC_N;
+}
+
+/**
+ * struct xscaler_device - Xilinx Scaler device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @formats: V4L2 media bus formats at the sink and source pads
+ * @default_formats: default V4L2 media bus formats
+ * @vip_format: Xilinx Video IP format
+ * @crop: Active crop rectangle for the sink pad
+ * @num_hori_taps: number of vertical taps
+ * @num_vert_taps: number of vertical taps
+ * @max_num_phases: maximum number of phases
+ * @separate_yc_coef: separate coefficients for Luma(y) and Chroma(c)
+ * @separate_hv_coef: separate coefficients for Horizontal(h) and Vertical(v)
+ */
+struct xscaler_device {
+	struct xvip_device xvip;
+
+	struct media_pad pads[2];
+
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_format;
+	struct v4l2_rect crop;
+
+	u32 num_hori_taps;
+	u32 num_vert_taps;
+	u32 max_num_phases;
+	bool separate_yc_coef;
+	bool separate_hv_coef;
+};
+
+static inline struct xscaler_device *to_scaler(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xscaler_device, xvip.subdev);
+}
+
+/*
+ * V4L2 Subdevice Video Operations
+ */
+
+/**
+ * lanczos - Lanczos 2D FIR kernel convolution
+ * @x: phase
+ * @a: Lanczos kernel size
+ *
+ * Return: the coefficient value in fixed point format.
+ */
+static s16 lanczos(s16 x, s16 a)
+{
+	s16 pi;
+	s16 numerator;
+	s16 denominator;
+	s16 temp;
+
+	if (x < -a || x > a)
+		return 0;
+	else if (x == 0)
+		return fixp_new(1);
+
+	/* a * sin(pi * x) * sin(pi * x / a) / (pi * pi * x * x) */
+
+	pi = (fixp_new(157) << FRAC_N) / fixp_new(50);
+
+	if (x < 0)
+		x = -x;
+
+	/* sin(pi * x) */
+	temp = fixp_mult(fixp_new(180), x);
+	temp = fixp_sin16(temp >> FRAC_N);
+
+	/* a * sin(pi * x) */
+	numerator = fixp_mult(temp, a);
+
+	/* sin(pi * x / a) */
+	temp = (fixp_mult(fixp_new(180), x) << FRAC_N) / a;
+	temp = fixp_sin16(temp >> FRAC_N);
+
+	/* a * sin(pi * x) * sin(pi * x / a) */
+	numerator = fixp_mult(temp, numerator);
+
+	/* pi * pi * x * x */
+	denominator = fixp_mult(pi, pi);
+	temp = fixp_mult(x, x);
+	denominator = fixp_mult(temp, denominator);
+
+	return (numerator << FRAC_N) / denominator;
+}
+
+/**
+ * xscaler_set_coefs - generate and program the coefficient table
+ * @xscaler: scaler device
+ * @taps: maximum coefficient tap index
+ *
+ * Generate the coefficient table using Lanczos resampling, and program
+ * generated coefficients to the scaler. The generated coefficients are
+ * supposed to work regardless of resolutions.
+ *
+ * Return: 0 if the coefficient table is programmed, and -ENOMEM if memory
+ * allocation for the table fails.
+ */
+static int xscaler_set_coefs(struct xscaler_device *xscaler, s16 taps)
+{
+	s16 *coef;
+	s16 dy;
+	u32 coef_val;
+	u16 phases = xscaler->max_num_phases;
+	u16 i;
+	u16 j;
+
+	coef = kcalloc(phases, sizeof(*coef), GFP_KERNEL);
+	if (!coef)
+		return -ENOMEM;
+
+	for (i = 0; i < phases; i++) {
+		s16 sum = 0;
+
+		dy = ((fixp_new(i) << FRAC_N) / fixp_new(phases));
+
+		/* Generate Lanczos coefficients */
+		for (j = 0; j < taps; j++) {
+			coef[j] = lanczos(fixp_new(j - (taps >> 1)) + dy,
+					  fixp_new(taps >> 1));
+			sum += coef[j];
+		}
+
+		/* Program coefficients */
+		for (j = 0; j < taps; j += 2) {
+			/* Normalize and multiply coefficients */
+			coef_val = (((coef[j] << FRAC_N) << (FRAC_N - 2)) /
+				    sum) & 0xffff;
+			if (j + 1 < taps)
+				coef_val |= ((((coef[j + 1] << FRAC_N) <<
+					      (FRAC_N - 2)) / sum) & 0xffff) <<
+					    16;
+
+			xvip_write(&xscaler->xvip, XSCALER_COEF_DATA_IN,
+				   coef_val);
+		}
+	}
+
+	kfree(coef);
+
+	return 0;
+}
+
+static void xscaler_set_aperture(struct xscaler_device *xscaler)
+{
+	u16 start;
+	u16 end;
+	u32 scale_factor;
+
+	xvip_disable_reg_update(&xscaler->xvip);
+
+	/* set horizontal aperture */
+	start = xscaler->crop.left;
+	end = start + xscaler->crop.width - 1;
+	xvip_write(&xscaler->xvip, XSCALER_HAPERTURE,
+		   (end << XSCALER_APERTURE_END_SHIFT) |
+		   (start << XSCALER_APERTURE_START_SHIFT));
+
+	/* set vertical aperture */
+	start = xscaler->crop.top;
+	end = start + xscaler->crop.height - 1;
+	xvip_write(&xscaler->xvip, XSCALER_VAPERTURE,
+		   (end << XSCALER_APERTURE_END_SHIFT) |
+		   (start << XSCALER_APERTURE_START_SHIFT));
+
+	/* set scaling factors */
+	scale_factor = ((xscaler->crop.width << XSCALER_SF_SHIFT) /
+			xscaler->formats[XVIP_PAD_SOURCE].width) &
+		       XSCALER_SF_MASK;
+	xvip_write(&xscaler->xvip, XSCALER_HSF, scale_factor);
+
+	scale_factor = ((xscaler->crop.height << XSCALER_SF_SHIFT) /
+			xscaler->formats[XVIP_PAD_SOURCE].height) &
+		       XSCALER_SF_MASK;
+	xvip_write(&xscaler->xvip, XSCALER_VSF, scale_factor);
+
+	xvip_enable_reg_update(&xscaler->xvip);
+}
+
+static int xscaler_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	u32 width;
+	u32 height;
+
+	if (!enable) {
+		xvip_stop(&xscaler->xvip);
+		return 0;
+	}
+
+	/* set input width / height */
+	width = xscaler->formats[XVIP_PAD_SINK].width;
+	height = xscaler->formats[XVIP_PAD_SINK].height;
+	xvip_write(&xscaler->xvip, XSCALER_SOURCE_SIZE,
+		   (height << XSCALER_SIZE_VERT_SHIFT) |
+		   (width << XSCALER_SIZE_HORZ_SHIFT));
+
+	/* set output width / height */
+	width = xscaler->formats[XVIP_PAD_SOURCE].width;
+	height = xscaler->formats[XVIP_PAD_SOURCE].height;
+	xvip_write(&xscaler->xvip, XSCALER_OUTPUT_SIZE,
+		   (height << XSCALER_SIZE_VERT_SHIFT) |
+		   (width << XSCALER_SIZE_HORZ_SHIFT));
+
+	/* set aperture */
+	xscaler_set_aperture(xscaler);
+
+	xvip_start(&xscaler->xvip);
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Pad Operations
+ */
+
+static int xscaler_enum_frame_size(struct v4l2_subdev *subdev,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	format = v4l2_subdev_get_try_format(subdev, sd_state, fse->pad);
+
+	if (fse->index || fse->code != format->code)
+		return -EINVAL;
+
+	fse->min_width = XSCALER_MIN_WIDTH;
+	fse->max_width = XSCALER_MAX_WIDTH;
+	fse->min_height = XSCALER_MIN_HEIGHT;
+	fse->max_height = XSCALER_MAX_HEIGHT;
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+__xscaler_get_pad_format(struct xscaler_device *xscaler,
+			 struct v4l2_subdev_state *sd_state,
+			 unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xscaler->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xscaler->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static struct v4l2_rect *__xscaler_get_crop(struct xscaler_device *xscaler,
+					    struct v4l2_subdev_state *sd_state,
+					    u32 which)
+{
+	struct v4l2_rect *crop;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		crop = v4l2_subdev_get_try_crop(&xscaler->xvip.subdev,
+						sd_state,
+						XVIP_PAD_SINK);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		crop = &xscaler->crop;
+		break;
+	default:
+		crop = NULL;
+		break;
+	}
+
+	return crop;
+}
+
+static int xscaler_get_format(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xscaler_get_pad_format(xscaler, sd_state, fmt->pad,
+					  fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static void xscaler_try_crop(const struct v4l2_mbus_framefmt *sink,
+			     struct v4l2_rect *crop)
+{
+
+	crop->left = min_t(u32, crop->left, sink->width - XSCALER_MIN_WIDTH);
+	crop->top = min_t(u32, crop->top, sink->height - XSCALER_MIN_HEIGHT);
+	crop->width = clamp_t(u32, crop->width, XSCALER_MIN_WIDTH,
+			      sink->width - crop->left);
+	crop->height = clamp_t(u32, crop->height, XSCALER_MIN_HEIGHT,
+			       sink->height - crop->top);
+}
+
+static int xscaler_set_format(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+	struct v4l2_rect *crop;
+
+	format = __xscaler_get_pad_format(xscaler, sd_state, fmt->pad,
+					  fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	format->width = clamp_t(unsigned int, fmt->format.width,
+				  XSCALER_MIN_WIDTH, XSCALER_MAX_WIDTH);
+	format->height = clamp_t(unsigned int, fmt->format.height,
+				   XSCALER_MIN_HEIGHT, XSCALER_MAX_HEIGHT);
+
+	fmt->format = *format;
+
+	if (fmt->pad == XVIP_PAD_SINK) {
+		/* Set the crop rectangle to the full frame */
+		crop = __xscaler_get_crop(xscaler, sd_state, fmt->which);
+		if (!crop)
+			return -EINVAL;
+		crop->left = 0;
+		crop->top = 0;
+		crop->width = fmt->format.width;
+		crop->height = fmt->format.height;
+	}
+
+	return 0;
+}
+
+static int xscaler_get_selection(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_selection *sel)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+	struct v4l2_rect *crop;
+
+	if (sel->pad != XVIP_PAD_SINK)
+		return -EINVAL;
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+		format = __xscaler_get_pad_format(xscaler, sd_state,
+						  XVIP_PAD_SINK,
+						  sel->which);
+		if (!format)
+			return -EINVAL;
+
+		sel->r.left = 0;
+		sel->r.top = 0;
+		sel->r.width = format->width;
+		sel->r.height = format->height;
+		return 0;
+	case V4L2_SEL_TGT_CROP:
+		crop = __xscaler_get_crop(xscaler, sd_state, sel->which);
+		if (!crop)
+			return -EINVAL;
+		sel->r = *crop;
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int xscaler_set_selection(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_selection *sel)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+	struct v4l2_rect *crop;
+
+	if ((sel->target != V4L2_SEL_TGT_CROP) || (sel->pad != XVIP_PAD_SINK))
+		return -EINVAL;
+
+	format = __xscaler_get_pad_format(xscaler, sd_state, XVIP_PAD_SINK,
+					  sel->which);
+	if (!format)
+		return -EINVAL;
+
+	xscaler_try_crop(format, &sel->r);
+	crop = __xscaler_get_crop(xscaler, sd_state, sel->which);
+	if (!crop)
+		return -EINVAL;
+
+	*crop = sel->r;
+
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Operations
+ */
+
+static int xscaler_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xscaler->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state,
+					    XVIP_PAD_SOURCE);
+	*format = xscaler->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int xscaler_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_video_ops xscaler_video_ops = {
+	.s_stream = xscaler_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xscaler_pad_ops = {
+	.enum_mbus_code		= xvip_enum_mbus_code,
+	.enum_frame_size	= xscaler_enum_frame_size,
+	.get_fmt		= xscaler_get_format,
+	.set_fmt		= xscaler_set_format,
+	.get_selection		= xscaler_get_selection,
+	.set_selection		= xscaler_set_selection,
+};
+
+static struct v4l2_subdev_ops xscaler_ops = {
+	.video  = &xscaler_video_ops,
+	.pad    = &xscaler_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xscaler_internal_ops = {
+	.open	= xscaler_open,
+	.close	= xscaler_close,
+};
+
+/*
+ * Media Operations
+ */
+
+static const struct media_entity_operations xscaler_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/*
+ * Power Management
+ */
+
+static int __maybe_unused xscaler_pm_suspend(struct device *dev)
+{
+	struct xscaler_device *xscaler = dev_get_drvdata(dev);
+
+	xvip_suspend(&xscaler->xvip);
+
+	return 0;
+}
+
+static int __maybe_unused xscaler_pm_resume(struct device *dev)
+{
+	struct xscaler_device *xscaler = dev_get_drvdata(dev);
+
+	xvip_resume(&xscaler->xvip);
+
+	return 0;
+}
+
+/*
+ * Platform Device Driver
+ */
+
+static int xscaler_parse_of(struct xscaler_device *xscaler)
+{
+	struct device *dev = xscaler->xvip.dev;
+	struct device_node *node = xscaler->xvip.dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	int ret;
+
+	ports = of_get_child_by_name(node, "ports");
+	if (ports == NULL)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			const struct xvip_video_format *vip_format;
+
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "invalid format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			if (!xscaler->vip_format) {
+				xscaler->vip_format = vip_format;
+			} else if (xscaler->vip_format != vip_format) {
+				dev_err(dev, "in/out format mismatch in DT");
+				return -EINVAL;
+			}
+		}
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-hori-taps",
+				   &xscaler->num_hori_taps);
+	if (ret < 0)
+		return ret;
+
+	ret = of_property_read_u32(node, "xlnx,num-vert-taps",
+				   &xscaler->num_vert_taps);
+	if (ret < 0)
+		return ret;
+
+	ret = of_property_read_u32(node, "xlnx,max-num-phases",
+				   &xscaler->max_num_phases);
+	if (ret < 0)
+		return ret;
+
+	xscaler->separate_yc_coef =
+		of_property_read_bool(node, "xlnx,separate-yc-coef");
+
+	xscaler->separate_hv_coef =
+		of_property_read_bool(node, "xlnx,separate-hv-coef");
+
+	return 0;
+}
+
+static int xscaler_probe(struct platform_device *pdev)
+{
+	struct xscaler_device *xscaler;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *default_format;
+	u32 size;
+	int ret;
+
+	xscaler = devm_kzalloc(&pdev->dev, sizeof(*xscaler), GFP_KERNEL);
+	if (!xscaler)
+		return -ENOMEM;
+
+	xscaler->xvip.dev = &pdev->dev;
+
+	ret = xscaler_parse_of(xscaler);
+	if (ret < 0)
+		return ret;
+
+	ret = xvip_init_resources(&xscaler->xvip);
+	if (ret < 0)
+		return ret;
+
+	/* Reset and initialize the core */
+	xvip_reset(&xscaler->xvip);
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xscaler->xvip.subdev;
+	v4l2_subdev_init(subdev, &xscaler_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xscaler_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xscaler);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Initialize default and active formats */
+	default_format = &xscaler->default_formats[XVIP_PAD_SINK];
+	default_format->code = xscaler->vip_format->code;
+	default_format->field = V4L2_FIELD_NONE;
+	default_format->colorspace = V4L2_COLORSPACE_SRGB;
+	size = xvip_read(&xscaler->xvip, XSCALER_SOURCE_SIZE);
+	default_format->width = (size >> XSCALER_SIZE_HORZ_SHIFT) &
+				 XSCALER_SIZE_MASK;
+	default_format->height = (size >> XSCALER_SIZE_VERT_SHIFT) &
+				 XSCALER_SIZE_MASK;
+
+	xscaler->formats[XVIP_PAD_SINK] = *default_format;
+
+	default_format = &xscaler->default_formats[XVIP_PAD_SOURCE];
+	*default_format = xscaler->default_formats[XVIP_PAD_SINK];
+	size = xvip_read(&xscaler->xvip, XSCALER_OUTPUT_SIZE);
+	default_format->width = (size >> XSCALER_SIZE_HORZ_SHIFT) &
+				 XSCALER_SIZE_MASK;
+	default_format->height = (size >> XSCALER_SIZE_VERT_SHIFT) &
+				 XSCALER_SIZE_MASK;
+
+	xscaler->formats[XVIP_PAD_SOURCE] = *default_format;
+
+	xscaler->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xscaler->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xscaler_media_ops;
+
+	ret = media_entity_pads_init(&subdev->entity, 2, xscaler->pads);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xscaler);
+
+	xvip_print_version(&xscaler->xvip);
+
+	ret = xscaler_set_coefs(xscaler, (s16)xscaler->num_hori_taps);
+	if (ret < 0)
+		goto error;
+
+	if (xscaler->separate_hv_coef) {
+		ret = xscaler_set_coefs(xscaler, (s16)xscaler->num_vert_taps);
+		if (ret < 0)
+			goto error;
+	}
+
+	if (xscaler->separate_yc_coef) {
+		ret = xscaler_set_coefs(xscaler, (s16)xscaler->num_hori_taps);
+		if (ret < 0)
+			goto error;
+
+		if (xscaler->separate_hv_coef) {
+			ret = xscaler_set_coefs(xscaler,
+						(s16)xscaler->num_vert_taps);
+			if (ret < 0)
+				goto error;
+		}
+	}
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xscaler->xvip);
+	return ret;
+}
+
+static int xscaler_remove(struct platform_device *pdev)
+{
+	struct xscaler_device *xscaler = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xscaler->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+
+	xvip_cleanup_resources(&xscaler->xvip);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(xscaler_pm_ops, xscaler_pm_suspend, xscaler_pm_resume);
+
+static const struct of_device_id xscaler_of_id_table[] = {
+	{ .compatible = "xlnx,v-scaler-8.1" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xscaler_of_id_table);
+
+static struct platform_driver xscaler_driver = {
+	.driver			= {
+		.name		= "xilinx-scaler",
+		.pm		= &xscaler_pm_ops,
+		.of_match_table	= xscaler_of_id_table,
+	},
+	.probe			= xscaler_probe,
+	.remove			= xscaler_remove,
+};
+
+module_platform_driver(xscaler_driver);
+
+MODULE_DESCRIPTION("Xilinx Scaler Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-scenechange-channel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-scenechange-channel.c
@@ -0,0 +1,464 @@
+//SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Scene Change Detection driver
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Authors: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
+ *          Satish Kumar Nagireddy <satish.nagireddy.nagireddy@xilinx.com>
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/of.h>
+#include <linux/xilinx-v4l2-events.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-scenechange.h"
+#include "xilinx-vip.h"
+
+#define XSCD_DEFAULT_WIDTH	3840
+#define XSCD_DEFAULT_HEIGHT	2160
+#define XSCD_MAX_WIDTH		8192
+#define XSCD_MAX_HEIGHT		4320
+#define XSCD_MIN_WIDTH		64
+#define XSCD_MIN_HEIGHT		64
+
+#define XSCD_V_SUBSAMPLING		16
+#define XSCD_BYTE_ALIGN			16
+#define MULTIPLICATION_FACTOR		100
+
+#define XSCD_SCENE_CHANGE		1
+#define XSCD_NO_SCENE_CHANGE		0
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+static int xscd_enum_mbus_code(struct v4l2_subdev *subdev,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_mbus_code_enum *code)
+{
+	return 0;
+}
+
+static int xscd_enum_frame_size(struct v4l2_subdev *subdev,
+				struct v4l2_subdev_state *sd_state,
+				struct v4l2_subdev_frame_size_enum *fse)
+{
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+__xscd_get_pad_format(struct xscd_chan *chan,
+		      struct v4l2_subdev_state *sd_state,
+		      unsigned int pad, u32 which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_format(&chan->subdev, sd_state,
+						  pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &chan->format;
+	default:
+		return NULL;
+	}
+	return NULL;
+}
+
+static int xscd_get_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xscd_chan *chan = to_xscd_chan(subdev);
+
+	fmt->format = *__xscd_get_pad_format(chan, sd_state, fmt->pad,
+					     fmt->which);
+	return 0;
+}
+
+static int xscd_set_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xscd_chan *chan = to_xscd_chan(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xscd_get_pad_format(chan, sd_state, fmt->pad, fmt->which);
+	format->width = clamp_t(unsigned int, fmt->format.width,
+				XSCD_MIN_WIDTH, XSCD_MAX_WIDTH);
+	format->height = clamp_t(unsigned int, fmt->format.height,
+				 XSCD_MIN_HEIGHT, XSCD_MAX_HEIGHT);
+	format->code = fmt->format.code;
+	/*
+	 * If memory based, SCD can support interlaced alternate mode because
+	 * SCD is agnostic to field. If stream based, SCD does not have a fid
+	 * pin so interlaced alternate mode is not supported there.
+	 */
+	if (chan->xscd->memory_based)
+		format->field = fmt->format.field;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xscd_chan_get_vid_fmt(u32 media_bus_fmt, bool memory_based)
+{
+	u32 vid_fmt;
+
+	if (memory_based) {
+		switch (media_bus_fmt) {
+		case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		case MEDIA_BUS_FMT_UYVY8_1X16:
+		case MEDIA_BUS_FMT_VUY8_1X24:
+			vid_fmt = XSCD_VID_FMT_Y8;
+			break;
+		case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		case MEDIA_BUS_FMT_UYVY10_1X20:
+		case MEDIA_BUS_FMT_VUY10_1X30:
+			vid_fmt = XSCD_VID_FMT_Y10;
+			break;
+		default:
+			vid_fmt = XSCD_VID_FMT_Y8;
+		}
+
+		return vid_fmt;
+	}
+
+	/* Streaming based */
+	switch (media_bus_fmt) {
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+	case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		vid_fmt = XSCD_VID_FMT_YUV_420;
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+		vid_fmt = XSCD_VID_FMT_YUV_422;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+	case MEDIA_BUS_FMT_VUY10_1X30:
+		vid_fmt = XSCD_VID_FMT_YUV_444;
+		break;
+	case MEDIA_BUS_FMT_RBG888_1X24:
+	case MEDIA_BUS_FMT_RBG101010_1X30:
+		vid_fmt = XSCD_VID_FMT_RGB;
+		break;
+	default:
+		vid_fmt = XSCD_VID_FMT_YUV_420;
+	}
+
+	return vid_fmt;
+}
+
+/**
+ * xscd_chan_configure_params - Program parameters to HW registers
+ * @chan: Driver specific channel struct pointer
+ */
+static void xscd_chan_configure_params(struct xscd_chan *chan)
+{
+	u32 vid_fmt, stride;
+
+	xscd_write(chan->iomem, XSCD_WIDTH_OFFSET, chan->format.width);
+
+	/* Stride is required only for memory based IP, not for streaming IP */
+	if (chan->xscd->memory_based) {
+		stride = roundup(chan->format.width, XSCD_BYTE_ALIGN);
+		xscd_write(chan->iomem, XSCD_STRIDE_OFFSET, stride);
+	}
+
+	xscd_write(chan->iomem, XSCD_HEIGHT_OFFSET, chan->format.height);
+
+	/* Hardware video format */
+	vid_fmt = xscd_chan_get_vid_fmt(chan->format.code,
+					chan->xscd->memory_based);
+	xscd_write(chan->iomem, XSCD_VID_FMT_OFFSET, vid_fmt);
+
+	/*
+	 * This is the vertical subsampling factor of the input image. Instead
+	 * of sampling every line to calculate the histogram, IP uses this
+	 * register value to sample only specific lines of the frame.
+	 */
+	xscd_write(chan->iomem, XSCD_SUBSAMPLE_OFFSET, XSCD_V_SUBSAMPLING);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Operations
+ */
+
+static int xscd_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	int ret = 0;
+	struct xscd_chan *chan = container_of(ctrl->handler, struct xscd_chan,
+					      ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_SCD_THRESHOLD:
+		chan->threshold = ctrl->val;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+static int xscd_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xscd_chan *chan = to_xscd_chan(subdev);
+	struct xscd_device *xscd = chan->xscd;
+
+	if (enable)
+		xscd_chan_configure_params(chan);
+
+	xscd_dma_enable_channel(&chan->dmachan, enable);
+
+	/*
+	 * Resolution change doesn't work in stream based mode unless
+	 * the device is reset.
+	 */
+	if (!enable && !xscd->memory_based) {
+		gpiod_set_value_cansleep(xscd->rst_gpio, XSCD_RESET_ASSERT);
+		gpiod_set_value_cansleep(xscd->rst_gpio, XSCD_RESET_DEASSERT);
+	}
+
+	return 0;
+}
+
+static int xscd_subscribe_event(struct v4l2_subdev *sd,
+				struct v4l2_fh *fh,
+				struct v4l2_event_subscription *sub)
+{
+	int ret;
+	struct xscd_chan *chan = to_xscd_chan(sd);
+
+	mutex_lock(&chan->lock);
+
+	switch (sub->type) {
+	case V4L2_EVENT_XLNXSCD:
+		ret = v4l2_event_subscribe(fh, sub, 1, NULL);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&chan->lock);
+
+	return ret;
+}
+
+static int xscd_unsubscribe_event(struct v4l2_subdev *sd,
+				  struct v4l2_fh *fh,
+				  struct v4l2_event_subscription *sub)
+{
+	int ret;
+	struct xscd_chan *chan = to_xscd_chan(sd);
+
+	mutex_lock(&chan->lock);
+	ret = v4l2_event_unsubscribe(fh, sub);
+	mutex_unlock(&chan->lock);
+
+	return ret;
+}
+
+static int xscd_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static int xscd_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops xscd_ctrl_ops = {
+	.s_ctrl	= xscd_s_ctrl
+};
+
+static const struct v4l2_ctrl_config xscd_ctrls[] = {
+	{
+		.ops = &xscd_ctrl_ops,
+		.id = V4L2_CID_XILINX_SCD_THRESHOLD,
+		.name = "Threshold Value",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.max = 100,
+		.step = 1,
+		.def = 50,
+	}
+};
+
+static const struct v4l2_subdev_core_ops xscd_core_ops = {
+	.subscribe_event = xscd_subscribe_event,
+	.unsubscribe_event = xscd_unsubscribe_event
+};
+
+static struct v4l2_subdev_video_ops xscd_video_ops = {
+	.s_stream = xscd_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xscd_pad_ops = {
+	.enum_mbus_code = xscd_enum_mbus_code,
+	.enum_frame_size = xscd_enum_frame_size,
+	.get_fmt = xscd_get_format,
+	.set_fmt = xscd_set_format,
+};
+
+static struct v4l2_subdev_ops xscd_ops = {
+	.core = &xscd_core_ops,
+	.video = &xscd_video_ops,
+	.pad = &xscd_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xscd_internal_ops = {
+	.open = xscd_open,
+	.close = xscd_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xscd_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+void xscd_chan_event_notify(struct xscd_chan *chan)
+{
+	u32 *eventdata;
+	u32 sad;
+
+	sad = xscd_read(chan->iomem, XSCD_SAD_OFFSET);
+	sad = (sad * XSCD_V_SUBSAMPLING * MULTIPLICATION_FACTOR) /
+	       (chan->format.width * chan->format.height);
+	eventdata = (u32 *)&chan->event.u.data;
+
+	if (sad > chan->threshold)
+		eventdata[0] = XSCD_SCENE_CHANGE;
+	else
+		eventdata[0] = XSCD_NO_SCENE_CHANGE;
+
+	chan->event.type = V4L2_EVENT_XLNXSCD;
+	v4l2_subdev_notify_event(&chan->subdev, &chan->event);
+}
+
+/**
+ * xscd_chan_init - Initialize the V4L2 subdev for a channel
+ * @xscd: Pointer to the SCD device structure
+ * @chan_id: Channel id
+ * @node: device node
+ *
+ * Return: '0' on success and failure value on error
+ */
+int xscd_chan_init(struct xscd_device *xscd, unsigned int chan_id,
+		   struct device_node *node)
+{
+	struct xscd_chan *chan = &xscd->chans[chan_id];
+	struct v4l2_subdev *subdev;
+	unsigned int num_pads;
+	int ret;
+	unsigned int i;
+
+	mutex_init(&chan->lock);
+	chan->xscd = xscd;
+	chan->id = chan_id;
+	chan->iomem = chan->xscd->iomem + chan->id * XSCD_CHAN_OFFSET;
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &chan->subdev;
+	v4l2_subdev_init(subdev, &xscd_ops);
+	subdev->dev = chan->xscd->dev;
+	subdev->fwnode = of_fwnode_handle(node);
+	subdev->internal_ops = &xscd_internal_ops;
+	snprintf(subdev->name, sizeof(subdev->name), "xlnx-scdchan.%u",
+		 chan_id);
+	v4l2_set_subdevdata(subdev, chan);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+
+	/* Initialize default format */
+	chan->format.code = MEDIA_BUS_FMT_VYYUYY8_1X24;
+	chan->format.field = V4L2_FIELD_NONE;
+	chan->format.width = XSCD_DEFAULT_WIDTH;
+	chan->format.height = XSCD_DEFAULT_HEIGHT;
+
+	/* Initialize media pads */
+	num_pads = xscd->memory_based ? 1 : 2;
+
+	chan->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	if (!xscd->memory_based)
+		chan->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	ret = media_entity_pads_init(&subdev->entity, num_pads, chan->pads);
+	if (ret < 0)
+		goto media_init_error;
+
+	subdev->entity.ops = &xscd_media_ops;
+
+	/* Initialize V4L2 Control Handler */
+	v4l2_ctrl_handler_init(&chan->ctrl_handler, ARRAY_SIZE(xscd_ctrls));
+
+	for (i = 0; i < ARRAY_SIZE(xscd_ctrls); i++) {
+		struct v4l2_ctrl *ctrl;
+
+		dev_dbg(chan->xscd->dev, "%d ctrl = 0x%x\n", i,
+			xscd_ctrls[i].id);
+		ctrl = v4l2_ctrl_new_custom(&chan->ctrl_handler, &xscd_ctrls[i],
+					    NULL);
+		if (!ctrl) {
+			dev_err(chan->xscd->dev, "Failed for %s ctrl\n",
+				xscd_ctrls[i].name);
+			goto ctrl_handler_error;
+		}
+	}
+
+	if (chan->ctrl_handler.error) {
+		dev_err(chan->xscd->dev, "failed to add controls\n");
+		ret = chan->ctrl_handler.error;
+		goto ctrl_handler_error;
+	}
+
+	subdev->ctrl_handler = &chan->ctrl_handler;
+
+	ret = v4l2_ctrl_handler_setup(&chan->ctrl_handler);
+	if (ret < 0) {
+		dev_err(chan->xscd->dev, "failed to set controls\n");
+		goto ctrl_handler_error;
+	}
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(chan->xscd->dev, "failed to register subdev\n");
+		goto ctrl_handler_error;
+	}
+
+	dev_info(chan->xscd->dev, "Scene change detection channel found!\n");
+	return 0;
+
+ctrl_handler_error:
+	v4l2_ctrl_handler_free(&chan->ctrl_handler);
+media_init_error:
+	media_entity_cleanup(&subdev->entity);
+	mutex_destroy(&chan->lock);
+	return ret;
+}
+
+/**
+ * xscd_chan_cleanup - Clean up the V4L2 subdev for a channel
+ * @xscd: Pointer to the SCD device structure
+ * @chan_id: Channel id
+ * @node: device node
+ */
+void xscd_chan_cleanup(struct xscd_device *xscd, unsigned int chan_id,
+		       struct device_node *node)
+{
+	struct xscd_chan *chan = &xscd->chans[chan_id];
+	struct v4l2_subdev *subdev = &chan->subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&chan->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	mutex_destroy(&chan->lock);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-scenechange-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-scenechange-dma.c
@@ -0,0 +1,554 @@
+//SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Scene Change Detection DMA driver
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Authors: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
+ *          Satish Kumar Nagireddy <satish.nagireddy.nagireddy@xilinx.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/of_dma.h>
+#include <linux/slab.h>
+
+#include "../../../dma/dmaengine.h"
+
+#include "xilinx-scenechange.h"
+
+/**
+ * xscd_dma_start - Start the SCD core
+ * @xscd: The SCD device
+ * @channels: Bitmask of enabled channels
+ */
+static void xscd_dma_start(struct xscd_device *xscd, unsigned int channels)
+{
+	xscd_write(xscd->iomem, XSCD_IE_OFFSET, XSCD_IE_AP_DONE);
+	xscd_write(xscd->iomem, XSCD_GIE_OFFSET, XSCD_GIE_EN);
+	xscd_write(xscd->iomem, XSCD_CHAN_EN_OFFSET, channels);
+
+	xscd_set(xscd->iomem, XSCD_CTRL_OFFSET,
+		 xscd->memory_based ? XSCD_CTRL_AP_START
+				    : XSCD_CTRL_AP_START |
+				      XSCD_CTRL_AUTO_RESTART);
+
+	xscd->running = true;
+}
+
+/**
+ * xscd_dma_stop - Stop the SCD core
+ * @xscd: The SCD device
+ */
+static void xscd_dma_stop(struct xscd_device *xscd)
+{
+	xscd_clr(xscd->iomem, XSCD_CTRL_OFFSET,
+		 xscd->memory_based ? XSCD_CTRL_AP_START
+				    : XSCD_CTRL_AP_START |
+				      XSCD_CTRL_AUTO_RESTART);
+
+	xscd->running = false;
+}
+
+/**
+ * xscd_dma_setup_channel - Setup a channel for transfer
+ * @chan: Driver specific channel struct pointer
+ *
+ * Return: 1 if the channel starts to run for a new transfer. Otherwise, 0.
+ */
+static int xscd_dma_setup_channel(struct xscd_dma_chan *chan)
+{
+	struct xscd_dma_tx_descriptor *desc;
+
+	if (!chan->enabled)
+		return 0;
+
+	if (list_empty(&chan->pending_list))
+		return 0;
+
+	desc = list_first_entry(&chan->pending_list,
+				struct xscd_dma_tx_descriptor, node);
+	list_del(&desc->node);
+
+	xscd_write(chan->iomem, XSCD_ADDR_OFFSET, desc->sw.luma_plane_addr);
+	chan->active_desc = desc;
+
+	return 1;
+}
+
+/**
+ * xscd_dma_kick - Start a run of the SCD core if channels are ready
+ * @xscd: The SCD device
+ *
+ * This function starts a single run of the SCD core when all the following
+ * conditions are met:
+ *
+ * - The SCD is not currently running
+ * - At least one channel is enabled and has buffers available
+ *
+ * It can be used to start the SCD when a buffer is queued, when a channel
+ * starts streaming, or to start the next run. Calling this function is only
+ * valid for memory-based mode and is not permitted for stream-based mode.
+ *
+ * The running state for all channels is updated. Channels that are being
+ * stopped are signalled through the channel wait queue.
+ *
+ * The function must be called with the xscd_device lock held.
+ */
+static void xscd_dma_kick(struct xscd_device *xscd)
+{
+	unsigned int channels = 0;
+	unsigned int i;
+
+	lockdep_assert_held(&xscd->lock);
+
+	if (xscd->running)
+		return;
+
+	for (i = 0; i < xscd->num_streams; i++) {
+		struct xscd_dma_chan *chan = xscd->channels[i];
+		unsigned long flags;
+		unsigned int running;
+		bool stopped;
+
+		spin_lock_irqsave(&chan->lock, flags);
+		running = xscd_dma_setup_channel(chan);
+		stopped = chan->running && !running;
+		chan->running = running;
+		spin_unlock_irqrestore(&chan->lock, flags);
+
+		channels |= running << chan->id;
+		if (stopped)
+			wake_up(&chan->wait);
+	}
+
+	if (channels)
+		xscd_dma_start(xscd, channels);
+	else
+		xscd_dma_stop(xscd);
+}
+
+/**
+ * xscd_dma_enable_channel - Enable/disable a channel
+ * @chan: Driver specific channel struct pointer
+ * @enable: True to enable the channel, false to disable it
+ *
+ * This function enables or disable a channel. When operating in memory-based
+ * mode, enabling a channel kicks processing if buffers are available for any
+ * enabled channel and the SCD core is idle. When operating in stream-based
+ * mode, the SCD core is started or stopped synchronously when then channel is
+ * enabled or disabled.
+ *
+ * This function must be called in non-atomic, non-interrupt context.
+ */
+void xscd_dma_enable_channel(struct xscd_dma_chan *chan, bool enable)
+{
+	struct xscd_device *xscd = chan->xscd;
+
+	if (enable) {
+		/*
+		 * FIXME: Don't set chan->enabled to false here, it will be
+		 * done in xscd_dma_terminate_all(). This works around a bug
+		 * introduced in commit 2e77607047c6 ("xilinx: v4l2: dma: Add
+		 * multiple output support") that stops all channels when the
+		 * first one is stopped, even though they are part of
+		 * independent pipelines. This workaround should be safe as
+		 * long as dmaengine_terminate_all() is called after
+		 * xvip_pipeline_set_stream().
+		 */
+		spin_lock_irq(&chan->lock);
+		chan->enabled = true;
+		spin_unlock_irq(&chan->lock);
+	}
+
+	if (xscd->memory_based) {
+		if (enable) {
+			spin_lock_irq(&xscd->lock);
+			xscd_dma_kick(xscd);
+			spin_unlock_irq(&xscd->lock);
+		}
+	} else {
+		if (enable)
+			xscd_dma_start(xscd, BIT(chan->id));
+		else
+			xscd_dma_stop(xscd);
+	}
+}
+
+/**
+ * xscd_dma_irq_handler - scdma Interrupt handler
+ * @xscd: Pointer to the SCD device structure
+ */
+void xscd_dma_irq_handler(struct xscd_device *xscd)
+{
+	unsigned int i;
+
+	/*
+	 * Mark the active descriptors as complete, move them to the done list
+	 * and schedule the tasklet to clean them up.
+	 */
+	for (i = 0; i < xscd->num_streams; ++i) {
+		struct xscd_dma_chan *chan = xscd->channels[i];
+		struct xscd_dma_tx_descriptor *desc = chan->active_desc;
+
+		if (!desc)
+			continue;
+
+		dma_cookie_complete(&desc->async_tx);
+		xscd_chan_event_notify(&xscd->chans[i]);
+
+		spin_lock(&chan->lock);
+		list_add_tail(&desc->node, &chan->done_list);
+		chan->active_desc = NULL;
+		spin_unlock(&chan->lock);
+
+		tasklet_schedule(&chan->tasklet);
+	}
+
+	/* Start the next run, if any. */
+	spin_lock(&xscd->lock);
+	xscd->running = false;
+	xscd_dma_kick(xscd);
+	spin_unlock(&xscd->lock);
+}
+
+/* -----------------------------------------------------------------------------
+ * DMA Engine
+ */
+
+/**
+ * xscd_dma_tx_submit - Submit DMA transaction
+ * @tx: Async transaction descriptor
+ *
+ * Return: cookie value on success and failure value on error
+ */
+static dma_cookie_t xscd_dma_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+	struct xscd_dma_tx_descriptor *desc = to_xscd_dma_tx_descriptor(tx);
+	struct xscd_dma_chan *chan = to_xscd_dma_chan(tx->chan);
+	dma_cookie_t cookie;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+	cookie = dma_cookie_assign(tx);
+	list_add_tail(&desc->node, &chan->pending_list);
+	spin_unlock_irqrestore(&chan->lock, flags);
+
+	return cookie;
+}
+
+/**
+ * xscd_dma_free_desc_list - Free descriptors list
+ * @chan: Driver specific dma channel
+ * @list: List to parse and delete the descriptor
+ */
+static void xscd_dma_free_desc_list(struct xscd_dma_chan *chan,
+				    struct list_head *list)
+{
+	struct xscd_dma_tx_descriptor *desc, *next;
+
+	list_for_each_entry_safe(desc, next, list, node) {
+		list_del(&desc->node);
+		kfree(desc);
+	}
+}
+
+/**
+ * xscd_dma_free_descriptors - Free channel descriptors
+ * @chan: Driver specific dma channel
+ */
+static void xscd_dma_free_descriptors(struct xscd_dma_chan *chan)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	xscd_dma_free_desc_list(chan, &chan->pending_list);
+	xscd_dma_free_desc_list(chan, &chan->done_list);
+	kfree(chan->active_desc);
+
+	chan->active_desc = NULL;
+	INIT_LIST_HEAD(&chan->pending_list);
+	INIT_LIST_HEAD(&chan->done_list);
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * scd_dma_chan_desc_cleanup - Clean channel descriptors
+ * @chan: Driver specific dma channel
+ */
+static void xscd_dma_chan_desc_cleanup(struct xscd_dma_chan *chan)
+{
+	struct xscd_dma_tx_descriptor *desc, *next;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	list_for_each_entry_safe(desc, next, &chan->done_list, node) {
+		dma_async_tx_callback callback;
+		void *callback_param;
+
+		list_del(&desc->node);
+
+		/* Run the link descriptor callback function */
+		callback = desc->async_tx.callback;
+		callback_param = desc->async_tx.callback_param;
+		if (callback) {
+			spin_unlock_irqrestore(&chan->lock, flags);
+			callback(callback_param);
+			spin_lock_irqsave(&chan->lock, flags);
+		}
+
+		kfree(desc);
+	}
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xscd_dma_dma_prep_interleaved - prepare a descriptor for a
+ * DMA_SLAVE transaction
+ * @dchan: DMA channel
+ * @xt: Interleaved template pointer
+ * @flags: transfer ack flags
+ *
+ * Return: Async transaction descriptor on success and NULL on failure
+ */
+static struct dma_async_tx_descriptor *
+xscd_dma_prep_interleaved(struct dma_chan *dchan,
+			  struct dma_interleaved_template *xt,
+			  unsigned long flags)
+{
+	struct xscd_dma_chan *chan = to_xscd_dma_chan(dchan);
+	struct xscd_dma_tx_descriptor *desc;
+	struct xscd_dma_desc *sw;
+
+	desc = kzalloc(sizeof(*desc), GFP_KERNEL);
+	if (!desc)
+		return NULL;
+
+	dma_async_tx_descriptor_init(&desc->async_tx, &chan->common);
+	desc->async_tx.tx_submit = xscd_dma_tx_submit;
+	async_tx_ack(&desc->async_tx);
+
+	sw = &desc->sw;
+	sw->vsize = xt->numf;
+	sw->hsize = xt->sgl[0].size;
+	sw->stride = xt->sgl[0].size + xt->sgl[0].icg;
+	sw->luma_plane_addr = xt->src_start;
+
+	return &desc->async_tx;
+}
+
+static bool xscd_dma_is_running(struct xscd_dma_chan *chan)
+{
+	bool running;
+
+	spin_lock_irq(&chan->lock);
+	running = chan->running;
+	spin_unlock_irq(&chan->lock);
+
+	return running;
+}
+
+/**
+ * xscd_dma_terminate_all - Halt the channel and free descriptors
+ * @dchan: Driver specific dma channel pointer
+ *
+ * Return: 0
+ */
+static int xscd_dma_terminate_all(struct dma_chan *dchan)
+{
+	struct xscd_dma_chan *chan = to_xscd_dma_chan(dchan);
+	int ret;
+
+	spin_lock_irq(&chan->lock);
+	chan->enabled = false;
+	spin_unlock_irq(&chan->lock);
+
+	/* Wait for any on-going transfer to complete. */
+	ret = wait_event_timeout(chan->wait, !xscd_dma_is_running(chan),
+				 msecs_to_jiffies(100));
+	WARN_ON(ret == 0);
+
+	xscd_dma_free_descriptors(chan);
+	return 0;
+}
+
+/**
+ * xscd_dma_issue_pending - Issue pending transactions
+ * @dchan: DMA channel
+ */
+static void xscd_dma_issue_pending(struct dma_chan *dchan)
+{
+	struct xscd_dma_chan *chan = to_xscd_dma_chan(dchan);
+	struct xscd_device *xscd = chan->xscd;
+	unsigned long flags;
+
+	spin_lock_irqsave(&xscd->lock, flags);
+	xscd_dma_kick(xscd);
+	spin_unlock_irqrestore(&xscd->lock, flags);
+}
+
+static enum dma_status xscd_dma_tx_status(struct dma_chan *dchan,
+					  dma_cookie_t cookie,
+					  struct dma_tx_state *txstate)
+{
+	return dma_cookie_status(dchan, cookie, txstate);
+}
+
+/**
+ * xscd_dma_free_chan_resources - Free channel resources
+ * @dchan: DMA channel
+ */
+static void xscd_dma_free_chan_resources(struct dma_chan *dchan)
+{
+	struct xscd_dma_chan *chan = to_xscd_dma_chan(dchan);
+
+	xscd_dma_free_descriptors(chan);
+}
+
+/**
+ * xscd_dma_do_tasklet - Schedule completion tasklet
+ * @data: Pointer to the Xilinx scdma channel structure
+ */
+static void xscd_dma_do_tasklet(unsigned long data)
+{
+	struct xscd_dma_chan *chan = (struct xscd_dma_chan *)data;
+
+	xscd_dma_chan_desc_cleanup(chan);
+}
+
+/**
+ * xscd_dma_alloc_chan_resources - Allocate channel resources
+ * @dchan: DMA channel
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xscd_dma_alloc_chan_resources(struct dma_chan *dchan)
+{
+	dma_cookie_init(dchan);
+	return 0;
+}
+
+/**
+ * of_scdma_xilinx_xlate - Translation function
+ * @dma_spec: Pointer to DMA specifier as found in the device tree
+ * @ofdma: Pointer to DMA controller data
+ *
+ * Return: DMA channel pointer on success and NULL on error
+ */
+static struct dma_chan *of_scdma_xilinx_xlate(struct of_phandle_args *dma_spec,
+					      struct of_dma *ofdma)
+{
+	struct xscd_device *xscd = ofdma->of_dma_data;
+	u32 chan_id = dma_spec->args[0];
+
+	if (chan_id >= xscd->num_streams)
+		return NULL;
+
+	if (!xscd->channels[chan_id])
+		return NULL;
+
+	return dma_get_slave_channel(&xscd->channels[chan_id]->common);
+}
+
+static void xscd_dma_chan_init(struct xscd_device *xscd, int chan_id)
+{
+	struct xscd_dma_chan *chan = &xscd->chans[chan_id].dmachan;
+
+	chan->id = chan_id;
+	chan->iomem = xscd->iomem + chan->id * XSCD_CHAN_OFFSET;
+	chan->xscd = xscd;
+
+	xscd->channels[chan->id] = chan;
+
+	spin_lock_init(&chan->lock);
+	INIT_LIST_HEAD(&chan->pending_list);
+	INIT_LIST_HEAD(&chan->done_list);
+	tasklet_init(&chan->tasklet, xscd_dma_do_tasklet,
+		     (unsigned long)chan);
+	init_waitqueue_head(&chan->wait);
+
+	chan->common.device = &xscd->dma_device;
+	list_add_tail(&chan->common.device_node, &xscd->dma_device.channels);
+}
+
+/**
+ * xscd_dma_chan_remove - Per Channel remove function
+ * @chan: Driver specific DMA channel
+ */
+static void xscd_dma_chan_remove(struct xscd_dma_chan *chan)
+{
+	list_del(&chan->common.device_node);
+}
+
+/**
+ * xscd_dma_init - Initialize the SCD DMA engine
+ * @xscd: Pointer to the SCD device structure
+ *
+ * Return: '0' on success and failure value on error
+ */
+int xscd_dma_init(struct xscd_device *xscd)
+{
+	struct dma_device *ddev = &xscd->dma_device;
+	unsigned int chan_id;
+	int ret;
+
+	/* Initialize the DMA engine */
+	ddev->dev = xscd->dev;
+	dma_set_mask(xscd->dev, DMA_BIT_MASK(32));
+
+	INIT_LIST_HEAD(&ddev->channels);
+	dma_cap_set(DMA_SLAVE, ddev->cap_mask);
+	dma_cap_set(DMA_PRIVATE, ddev->cap_mask);
+	ddev->device_alloc_chan_resources = xscd_dma_alloc_chan_resources;
+	ddev->device_free_chan_resources = xscd_dma_free_chan_resources;
+	ddev->device_tx_status = xscd_dma_tx_status;
+	ddev->device_issue_pending = xscd_dma_issue_pending;
+	ddev->device_terminate_all = xscd_dma_terminate_all;
+	ddev->device_prep_interleaved_dma = xscd_dma_prep_interleaved;
+
+	for (chan_id = 0; chan_id < xscd->num_streams; chan_id++)
+		xscd_dma_chan_init(xscd, chan_id);
+
+	ret = dma_async_device_register(ddev);
+	if (ret) {
+		dev_err(xscd->dev, "failed to register the dma device\n");
+		goto error;
+	}
+
+	ret = of_dma_controller_register(xscd->dev->of_node,
+					 of_scdma_xilinx_xlate, xscd);
+	if (ret) {
+		dev_err(xscd->dev, "failed to register DMA to DT DMA helper\n");
+		goto error_of_dma;
+	}
+
+	dev_info(xscd->dev, "Xilinx Scene Change DMA is initialized!\n");
+	return 0;
+
+error_of_dma:
+	dma_async_device_unregister(ddev);
+
+error:
+	for (chan_id = 0; chan_id < xscd->num_streams; chan_id++)
+		xscd_dma_chan_remove(xscd->channels[chan_id]);
+
+	return ret;
+}
+
+/**
+ * xscd_dma_cleanup - Clean up the SCD DMA engine
+ * @xscd: Pointer to the SCD device structure
+ *
+ * This function is the counterpart of xscd_dma_init() and cleans up the
+ * resources related to the DMA engine.
+ */
+void xscd_dma_cleanup(struct xscd_device *xscd)
+{
+	dma_async_device_unregister(&xscd->dma_device);
+	of_dma_controller_free(xscd->dev->of_node);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-scenechange.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-scenechange.c
@@ -0,0 +1,195 @@
+//SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Scene Change Detection driver
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Authors: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
+ *          Satish Kumar Nagireddy <satish.nagireddy.nagireddy@xilinx.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "xilinx-scenechange.h"
+
+static irqreturn_t xscd_irq_handler(int irq, void *data)
+{
+	struct xscd_device *xscd = (struct xscd_device *)data;
+	u32 status;
+
+	status = xscd_read(xscd->iomem, XSCD_ISR_OFFSET);
+	if (!(status & XSCD_IE_AP_DONE))
+		return IRQ_NONE;
+
+	xscd_write(xscd->iomem, XSCD_ISR_OFFSET, XSCD_IE_AP_DONE);
+
+	if (xscd->memory_based)
+		xscd_dma_irq_handler(xscd);
+	else
+		xscd_chan_event_notify(&xscd->chans[0]);
+
+	return IRQ_HANDLED;
+}
+
+static int xscd_init_resources(struct xscd_device *xscd)
+{
+	struct platform_device *pdev = to_platform_device(xscd->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xscd->iomem = devm_ioremap_resource(xscd->dev, res);
+	if (IS_ERR(xscd->iomem))
+		return PTR_ERR(xscd->iomem);
+
+	xscd->irq = platform_get_irq(pdev, 0);
+	if (xscd->irq < 0) {
+		dev_err(xscd->dev, "No valid irq found\n");
+		return -EINVAL;
+	}
+
+	xscd->clk = devm_clk_get(xscd->dev, NULL);
+	if (IS_ERR(xscd->clk))
+		return PTR_ERR(xscd->clk);
+
+	clk_prepare_enable(xscd->clk);
+	return 0;
+}
+
+static int xscd_parse_of(struct xscd_device *xscd)
+{
+	struct device *dev = xscd->dev;
+	struct device_node *node = xscd->dev->of_node;
+	int ret;
+
+	xscd->memory_based = of_property_read_bool(node, "xlnx,memorybased");
+	xscd->rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(xscd->rst_gpio)) {
+		if (PTR_ERR(xscd->rst_gpio) != -EPROBE_DEFER)
+			dev_err(dev, "Reset GPIO not setup in DT\n");
+
+		return PTR_ERR(xscd->rst_gpio);
+	}
+
+	ret = of_property_read_u32(node, "xlnx,numstreams",
+				   &xscd->num_streams);
+	if (ret < 0)
+		return ret;
+
+	if (!xscd->memory_based && xscd->num_streams != 1) {
+		dev_err(dev, "Stream-based mode only supports one stream\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int xscd_probe(struct platform_device *pdev)
+{
+	struct xscd_device *xscd;
+	struct device_node *subdev_node;
+	unsigned int id;
+	int ret;
+
+	xscd = devm_kzalloc(&pdev->dev, sizeof(*xscd), GFP_KERNEL);
+	if (!xscd)
+		return -ENOMEM;
+
+	spin_lock_init(&xscd->lock);
+
+	xscd->dev = &pdev->dev;
+	platform_set_drvdata(pdev, xscd);
+
+	ret = xscd_parse_of(xscd);
+	if (ret < 0)
+		return ret;
+
+	ret = xscd_init_resources(xscd);
+	if (ret < 0)
+		return ret;
+
+	/* Reset Scene Change Detection IP */
+	gpiod_set_value_cansleep(xscd->rst_gpio, XSCD_RESET_ASSERT);
+	gpiod_set_value_cansleep(xscd->rst_gpio, XSCD_RESET_DEASSERT);
+
+	/* Initialize the channels. */
+	xscd->chans = devm_kcalloc(xscd->dev, xscd->num_streams,
+				   sizeof(*xscd->chans), GFP_KERNEL);
+	if (!xscd->chans)
+		return -ENOMEM;
+
+	id = 0;
+	for_each_child_of_node(xscd->dev->of_node, subdev_node) {
+		if (id >= xscd->num_streams) {
+			dev_warn(&pdev->dev,
+				 "Too many channels, limiting to %u\n",
+				 xscd->num_streams);
+			of_node_put(subdev_node);
+			break;
+		}
+
+		ret = xscd_chan_init(xscd, id, subdev_node);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "Failed to initialize channel %u\n",
+				id);
+			return ret;
+		}
+
+		id++;
+	}
+
+	/* Initialize the DMA engine. */
+	ret = xscd_dma_init(xscd);
+	if (ret < 0)
+		dev_err(&pdev->dev, "Failed to initialize the DMA\n");
+
+	ret = devm_request_irq(xscd->dev, xscd->irq, xscd_irq_handler,
+			       IRQF_SHARED, dev_name(xscd->dev), xscd);
+	if (ret < 0)
+		dev_err(&pdev->dev, "Failed to request IRQ\n");
+
+	dev_info(xscd->dev, "scene change detect device found!\n");
+	return 0;
+}
+
+static int xscd_remove(struct platform_device *pdev)
+{
+	struct xscd_device *xscd = platform_get_drvdata(pdev);
+	struct device_node *subdev_node;
+	unsigned int id = 0;
+
+	for_each_child_of_node(xscd->dev->of_node, subdev_node) {
+		xscd_chan_cleanup(xscd, id, subdev_node);
+		id++;
+	}
+
+	xscd_dma_cleanup(xscd);
+	clk_disable_unprepare(xscd->clk);
+
+	return 0;
+}
+
+static const struct of_device_id xscd_of_id_table[] = {
+	{ .compatible = "xlnx,v-scd" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xscd_of_id_table);
+
+static struct platform_driver xscd_driver = {
+	.driver = {
+		.name		= "xilinx-scd",
+		.of_match_table	= xscd_of_id_table,
+	},
+	.probe			= xscd_probe,
+	.remove			= xscd_remove,
+};
+
+module_platform_driver(xscd_driver);
+
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("Xilinx Scene Change Detection");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-scenechange.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-scenechange.h
@@ -0,0 +1,245 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx Scene Change Detection driver
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Authors: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
+ *          Satish Kumar Nagireddy <satish.nagireddy.nagireddy@xilinx.com>
+ */
+
+#ifndef _XILINX_SCENECHANGE_H_
+#define _XILINX_SCENECHANGE_H_
+
+#include <linux/bitops.h>
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+#include <linux/xilinx-v4l2-controls.h>
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+struct clk;
+struct device;
+struct device_node;
+struct gpio_desc;
+
+/* Register/Descriptor Offsets */
+#define XSCD_CTRL_OFFSET		0x000
+#define XSCD_CTRL_AP_START		BIT(0)
+#define XSCD_CTRL_AP_DONE		BIT(1)
+#define XSCD_CTRL_AP_IDLE		BIT(2)
+#define XSCD_CTRL_AP_READY		BIT(3)
+#define XSCD_CTRL_AUTO_RESTART		BIT(7)
+
+#define XSCD_GIE_OFFSET			0x004
+#define XSCD_GIE_EN			BIT(0)
+
+#define XSCD_IE_OFFSET			0x008
+#define XSCD_IE_AP_DONE			BIT(0)
+#define XSCD_IE_AP_READY		BIT(1)
+
+#define XSCD_ISR_OFFSET			0x00c
+#define XSCD_WIDTH_OFFSET		0x010
+#define XSCD_HEIGHT_OFFSET		0x018
+#define XSCD_STRIDE_OFFSET		0x020
+#define XSCD_VID_FMT_OFFSET		0x028
+#define XSCD_VID_FMT_RGB		0
+#define XSCD_VID_FMT_YUV_444		1
+#define XSCD_VID_FMT_YUV_422		2
+#define XSCD_VID_FMT_YUV_420		3
+#define XSCD_VID_FMT_Y8			24
+#define XSCD_VID_FMT_Y10		25
+
+#define XSCD_SUBSAMPLE_OFFSET		0x030
+#define XSCD_SAD_OFFSET			0x038
+#define XSCD_ADDR_OFFSET		0x040
+#define XSCD_CHAN_OFFSET		0x100
+#define XSCD_CHAN_EN_OFFSET		0x780
+
+#define XSCD_MAX_CHANNELS		8
+
+#define XSCD_RESET_DEASSERT		(0)
+#define XSCD_RESET_ASSERT		(1)
+
+/****************************** PROTOTYPES ************************************/
+
+struct xscd_device;
+
+/**
+ * struct xscd_dma_desc - DMA channel
+ * @luma_plane_addr: Luma plane buffer address
+ * @vsize: width of the luma frame
+ * @hsize: height of the luma frame
+ * @stride: stride of the luma frame
+ */
+struct xscd_dma_desc {
+	dma_addr_t luma_plane_addr;
+	u32 vsize;
+	u32 hsize;
+	u32 stride;
+};
+
+/**
+ * struct xscd_dma_tx_descriptor - Per Transaction structure
+ * @async_tx: Async transaction descriptor
+ * @sw: Software Descriptor
+ * @node: Node in the channel descriptor list
+ */
+struct xscd_dma_tx_descriptor {
+	struct dma_async_tx_descriptor async_tx;
+	struct xscd_dma_desc sw;
+	struct list_head node;
+};
+
+static inline struct xscd_dma_tx_descriptor *
+to_xscd_dma_tx_descriptor(struct dma_async_tx_descriptor *tx)
+{
+	return container_of(tx, struct xscd_dma_tx_descriptor, async_tx);
+}
+
+/**
+ * struct xscd_dma_chan - DMA Channel structure
+ * @xscd: SCD device
+ * @iomem: I/O memory address of the channel registers
+ * @id: scene change channel ID
+ * @common: DMA common channel
+ * @tasklet: Cleanup work after irq
+ * @lock: Protects pending_list, done_list, active_desc, enabled and running
+ * @pending_list: Descriptors waiting
+ * @done_list: Complete descriptors
+ * @active_desc: Currently active buffer being read/written to
+ * @enabled: Channel is enabled
+ * @running: Channel is running
+ * @wait: Wait queue to wait for the channel to stop
+ */
+struct xscd_dma_chan {
+	struct xscd_device *xscd;
+	void __iomem *iomem;
+	unsigned int id;
+
+	struct dma_chan common;
+	struct tasklet_struct tasklet;
+
+	spinlock_t lock;
+	struct list_head pending_list;
+	struct list_head done_list;
+	struct xscd_dma_tx_descriptor *active_desc;
+	unsigned int enabled;
+	unsigned int running;
+	wait_queue_head_t wait;
+};
+
+static inline struct xscd_dma_chan *to_xscd_dma_chan(struct dma_chan *chan)
+{
+	return container_of(chan, struct xscd_dma_chan, common);
+}
+
+/**
+ * struct xscd_chan - Video Stream structure
+ * @id: scene change channel ID
+ * @threshold: scene change detection threshold
+ * @iomem: I/O memory address of the channel registers
+ * @xscd: SCD device
+ * @subdev: V4L2 subdevice
+ * @ctrl_handler: V4L2 control handler
+ * @pads: media pads
+ * @format: active V4L2 media bus format for the pad
+ * @event: scene change event
+ * @dmachan: dma channel part of the scenechange stream
+ * @lock: lock to protect active stream count variable
+ */
+struct xscd_chan {
+	int id;
+	int threshold;
+	void __iomem *iomem;
+	struct xscd_device *xscd;
+	struct v4l2_subdev subdev;
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt format;
+	struct v4l2_event event;
+	struct xscd_dma_chan dmachan;
+
+	/* Lock to protect active stream count */
+	struct mutex lock;
+};
+
+static inline struct xscd_chan *to_xscd_chan(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xscd_chan, subdev);
+}
+
+/**
+ * struct xscd_device - Xilinx Scene Change Detection device structure
+ * @dev: (OF) device
+ * @iomem: device I/O register space remapped to kernel virtual memory
+ * @rst_gpio: reset GPIO
+ * @clk: video core clock
+ * @irq: Device IRQ
+ * @memory_based: Flag to identify memory based mode
+ * @num_streams: Number of streams in the design
+ * @chans: video stream instances
+ * @dma_device: DMA device structure
+ * @channels: DMA channels
+ * @lock: Protects the running field
+ * @running: True when the SCD core is running
+ */
+struct xscd_device {
+	struct device *dev;
+	void __iomem *iomem;
+	struct gpio_desc *rst_gpio;
+	struct clk *clk;
+	int irq;
+
+	u8 memory_based;
+	int num_streams;
+
+	struct xscd_chan *chans;
+
+	struct dma_device dma_device;
+	struct xscd_dma_chan *channels[XSCD_MAX_CHANNELS];
+
+	/* This lock is to protect the running field */
+	spinlock_t lock;
+	u8 running;
+};
+
+/*
+ * Register related operations
+ */
+static inline u32 xscd_read(void __iomem *iomem, u32 addr)
+{
+	return ioread32(iomem + addr);
+}
+
+static inline void xscd_write(void __iomem *iomem, u32 addr, u32 value)
+{
+	iowrite32(value, iomem + addr);
+}
+
+static inline void xscd_clr(void __iomem *iomem, u32 addr, u32 clr)
+{
+	xscd_write(iomem, addr, xscd_read(iomem, addr) & ~clr);
+}
+
+static inline void xscd_set(void __iomem *iomem, u32 addr, u32 set)
+{
+	xscd_write(iomem, addr, xscd_read(iomem, addr) | set);
+}
+
+void xscd_dma_enable_channel(struct xscd_dma_chan *chan, bool enable);
+void xscd_dma_irq_handler(struct xscd_device *xscd);
+int xscd_dma_init(struct xscd_device *xscd);
+void xscd_dma_cleanup(struct xscd_device *xscd);
+
+void xscd_chan_event_notify(struct xscd_chan *chan);
+int xscd_chan_init(struct xscd_device *xscd, unsigned int chan_id,
+		   struct device_node *node);
+void xscd_chan_cleanup(struct xscd_device *xscd, unsigned int chan_id,
+		       struct device_node *node);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-sdirxss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-sdirxss.c
@@ -0,0 +1,2667 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx SDI Rx Subsystem
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * Contacts: Vishal Sagar <vsagar@xilinx.com>
+ *
+ */
+
+#include <dt-bindings/media/xilinx-vip.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/compiler.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/spinlock_types.h>
+#include <linux/types.h>
+#include <linux/v4l2-dv-timings.h>
+#include <linux/v4l2-subdev.h>
+#include <linux/xilinx-sdirxss.h>
+#include <linux/xilinx-v4l2-controls.h>
+#include <media/hdr-ctrls.h>
+#include <media/media-entity.h>
+#include <media/v4l2-common.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+#include "xilinx-vip.h"
+
+/*
+ * SDI Rx register map, bitmask and offsets
+ */
+#define XSDIRX_RST_CTRL_REG		0x00
+#define XSDIRX_MDL_CTRL_REG		0x04
+#define XSDIRX_GLBL_IER_REG		0x0C
+#define XSDIRX_ISR_REG			0x10
+#define XSDIRX_IER_REG			0x14
+#define XSDIRX_ST352_VALID_REG		0x18
+#define XSDIRX_ST352_DS1_REG		0x1C
+#define XSDIRX_ST352_DS3_REG		0x20
+#define XSDIRX_ST352_DS5_REG		0x24
+#define XSDIRX_ST352_DS7_REG		0x28
+#define XSDIRX_ST352_DS9_REG		0x2C
+#define XSDIRX_ST352_DS11_REG		0x30
+#define XSDIRX_ST352_DS13_REG		0x34
+#define XSDIRX_ST352_DS15_REG		0x38
+#define XSDIRX_VERSION_REG		0x3C
+#define XSDIRX_SS_CONFIG_REG		0x40
+#define XSDIRX_MODE_DET_STAT_REG	0x44
+#define XSDIRX_TS_DET_STAT_REG		0x48
+#define XSDIRX_EDH_STAT_REG		0x4C
+#define XSDIRX_EDH_ERRCNT_EN_REG	0x50
+#define XSDIRX_EDH_ERRCNT_REG		0x54
+#define XSDIRX_CRC_ERRCNT_REG		0x58
+#define XSDIRX_VID_LOCK_WINDOW_REG	0x5C
+#define XSDIRX_SB_RX_STS_REG		0x60
+
+#define XSDIRX_RST_CTRL_SS_EN_MASK			BIT(0)
+#define XSDIRX_RST_CTRL_SRST_MASK			BIT(1)
+#define XSDIRX_RST_CTRL_RST_CRC_ERRCNT_MASK		BIT(2)
+#define XSDIRX_RST_CTRL_RST_EDH_ERRCNT_MASK		BIT(3)
+#define XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK		BIT(8)
+#define XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK	BIT(9)
+#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_OFFSET		10
+#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_MASK		GENMASK(12, 10)
+#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_YUV444		1
+
+#define XSDIRX_MDL_CTRL_FRM_EN_MASK		BIT(4)
+#define XSDIRX_MDL_CTRL_MODE_DET_EN_MASK	BIT(5)
+#define XSDIRX_MDL_CTRL_MODE_HD_EN_MASK		BIT(8)
+#define XSDIRX_MDL_CTRL_MODE_SD_EN_MASK		BIT(9)
+#define XSDIRX_MDL_CTRL_MODE_3G_EN_MASK		BIT(10)
+#define XSDIRX_MDL_CTRL_MODE_6G_EN_MASK		BIT(11)
+#define XSDIRX_MDL_CTRL_MODE_12GI_EN_MASK	BIT(12)
+#define XSDIRX_MDL_CTRL_MODE_12GF_EN_MASK	BIT(13)
+#define XSDIRX_MDL_CTRL_MODE_AUTO_DET_MASK	GENMASK(13, 8)
+
+#define XSDIRX_MDL_CTRL_FORCED_MODE_OFFSET	16
+#define XSDIRX_MDL_CTRL_FORCED_MODE_MASK	GENMASK(18, 16)
+
+#define XSDIRX_GLBL_INTR_EN_MASK	BIT(0)
+
+#define XSDIRX_INTR_VIDLOCK_MASK	BIT(0)
+#define XSDIRX_INTR_VIDUNLOCK_MASK	BIT(1)
+#define XSDIRX_INTR_VSYNC_MASK		BIT(2)
+#define XSDIRX_INTR_OVERFLOW_MASK	BIT(9)
+#define XSDIRX_INTR_UNDERFLOW_MASK	BIT(10)
+
+#define XSDIRX_INTR_ALL_MASK	(XSDIRX_INTR_VIDLOCK_MASK |\
+				XSDIRX_INTR_VIDUNLOCK_MASK |\
+				XSDIRX_INTR_VSYNC_MASK |\
+				XSDIRX_INTR_OVERFLOW_MASK |\
+				XSDIRX_INTR_UNDERFLOW_MASK)
+
+#define XSDIRX_ST352_VALID_DS1_MASK	BIT(0)
+#define XSDIRX_ST352_VALID_DS3_MASK	BIT(1)
+#define XSDIRX_ST352_VALID_DS5_MASK	BIT(2)
+#define XSDIRX_ST352_VALID_DS7_MASK	BIT(3)
+#define XSDIRX_ST352_VALID_DS9_MASK	BIT(4)
+#define XSDIRX_ST352_VALID_DS11_MASK	BIT(5)
+#define XSDIRX_ST352_VALID_DS13_MASK	BIT(6)
+#define XSDIRX_ST352_VALID_DS15_MASK	BIT(7)
+
+#define XSDIRX_MODE_DET_STAT_RX_MODE_MASK	GENMASK(2, 0)
+#define XSDIRX_MODE_DET_STAT_MODE_LOCK_MASK	BIT(3)
+#define XSDIRX_MODE_DET_STAT_ACT_STREAM_MASK	GENMASK(6, 4)
+#define XSDIRX_MODE_DET_STAT_ACT_STREAM_OFFSET	4
+#define XSDIRX_MODE_DET_STAT_LVLB_3G_MASK	BIT(7)
+
+#define XSDIRX_ACTIVE_STREAMS_1		0x0
+#define XSDIRX_ACTIVE_STREAMS_2		0x1
+#define XSDIRX_ACTIVE_STREAMS_4		0x2
+#define XSDIRX_ACTIVE_STREAMS_8		0x3
+#define XSDIRX_ACTIVE_STREAMS_16	0x4
+
+#define XSDIRX_TS_DET_STAT_LOCKED_MASK		BIT(0)
+#define XSDIRX_TS_DET_STAT_SCAN_MASK		BIT(1)
+#define XSDIRX_TS_DET_STAT_SCAN_OFFSET		(1)
+#define XSDIRX_TS_DET_STAT_FAMILY_MASK		GENMASK(7, 4)
+#define XSDIRX_TS_DET_STAT_FAMILY_OFFSET	(4)
+#define XSDIRX_TS_DET_STAT_RATE_MASK		GENMASK(11, 8)
+#define XSDIRX_TS_DET_STAT_RATE_OFFSET		(8)
+
+#define XSDIRX_TS_DET_STAT_RATE_NONE		0x0
+#define XSDIRX_TS_DET_STAT_RATE_96HZ		0x1
+#define XSDIRX_TS_DET_STAT_RATE_23_98HZ		0x2
+#define XSDIRX_TS_DET_STAT_RATE_24HZ		0x3
+#define XSDIRX_TS_DET_STAT_RATE_47_95HZ		0x4
+#define XSDIRX_TS_DET_STAT_RATE_25HZ		0x5
+#define XSDIRX_TS_DET_STAT_RATE_29_97HZ		0x6
+#define XSDIRX_TS_DET_STAT_RATE_30HZ		0x7
+#define XSDIRX_TS_DET_STAT_RATE_48HZ		0x8
+#define XSDIRX_TS_DET_STAT_RATE_50HZ		0x9
+#define XSDIRX_TS_DET_STAT_RATE_59_94HZ		0xA
+#define XSDIRX_TS_DET_STAT_RATE_60HZ		0xB
+#define XSDIRX_TS_DET_STAT_RATE_95_90HZ		0xC
+#define XSDIRX_TS_DET_STAT_RATE_100HZ		0xD
+#define XSDIRX_TS_DET_STAT_RATE_120HZ		0xE
+#define XSDIRX_TS_DET_STAT_RATE_119_88HZ	0xF
+
+#define XSDIRX_EDH_STAT_EDH_AP_MASK	BIT(0)
+#define XSDIRX_EDH_STAT_EDH_FF_MASK	BIT(1)
+#define XSDIRX_EDH_STAT_EDH_ANC_MASK	BIT(2)
+#define XSDIRX_EDH_STAT_AP_FLAG_MASK	GENMASK(8, 4)
+#define XSDIRX_EDH_STAT_FF_FLAG_MASK	GENMASK(13, 9)
+#define XSDIRX_EDH_STAT_ANC_FLAG_MASK	GENMASK(18, 14)
+#define XSDIRX_EDH_STAT_PKT_FLAG_MASK	GENMASK(22, 19)
+
+#define XSDIRX_EDH_ERRCNT_COUNT_MASK	GENMASK(15, 0)
+
+#define XSDIRX_CRC_ERRCNT_COUNT_MASK	GENMASK(31, 16)
+#define XSDIRX_CRC_ERRCNT_DS_CRC_MASK	GENMASK(15, 0)
+
+#define XSDIRX_VERSION_REV_MASK		GENMASK(7, 0)
+#define XSDIRX_VERSION_PATCHID_MASK	GENMASK(11, 8)
+#define XSDIRX_VERSION_VER_REV_MASK	GENMASK(15, 12)
+#define XSDIRX_VERSION_VER_MIN_MASK	GENMASK(23, 16)
+#define XSDIRX_VERSION_VER_MAJ_MASK	GENMASK(31, 24)
+
+#define XSDIRX_SS_CONFIG_EDH_INCLUDED_MASK		BIT(1)
+
+#define XSDIRX_STAT_SB_RX_TDATA_CHANGE_DONE_MASK	BIT(0)
+#define XSDIRX_STAT_SB_RX_TDATA_CHANGE_FAIL_MASK	BIT(1)
+#define XSDIRX_STAT_SB_RX_TDATA_GT_RESETDONE_MASK	BIT(2)
+#define XSDIRX_STAT_SB_RX_TDATA_GT_BITRATE_MASK		BIT(3)
+
+#define XSDIRX_DEFAULT_WIDTH	(1920)
+#define XSDIRX_DEFAULT_HEIGHT	(1080)
+
+#define XSDIRX_MAX_STR_LENGTH	16
+
+#define XSDIRXSS_SDI_STD_3G		0
+#define XSDIRXSS_SDI_STD_6G		1
+#define XSDIRXSS_SDI_STD_12G_8DS	2
+
+#define XSDIRX_DEFAULT_VIDEO_LOCK_WINDOW	0x3000
+
+#define XSDIRX_MODE_HD_MASK	0x0
+#define XSDIRX_MODE_SD_MASK	0x1
+#define XSDIRX_MODE_3G_MASK	0x2
+#define XSDIRX_MODE_6G_MASK	0x4
+#define XSDIRX_MODE_12GI_MASK	0x5
+#define XSDIRX_MODE_12GF_MASK	0x6
+
+/* Maximum number of events per file handle. */
+#define XSDIRX_MAX_EVENTS	(128)
+
+/* ST352 related macros */
+#define XST352_PAYLOAD_BYTE_MASK	0xFF
+#define XST352_PAYLOAD_BYTE1_SHIFT	0
+#define XST352_PAYLOAD_BYTE2_SHIFT	8
+#define XST352_PAYLOAD_BYTE3_SHIFT	16
+#define XST352_PAYLOAD_BYTE4_SHIFT	24
+
+#define XST352_BYTE1_ST292_1x720L_1_5G		0x84
+#define XST352_BYTE1_ST292_1x1080L_1_5G		0x85
+#define XST352_BYTE1_ST425_2008_750L_3GB	0x88
+#define XST352_BYTE1_ST425_2008_1125L_3GA	0x89
+#define XST352_BYTE1_ST372_DL_3GB		0x8A
+#define XST352_BYTE1_ST372_2x720L_3GB		0x8B
+#define XST352_BYTE1_ST372_2x1080L_3GB		0x8C
+#define XST352_BYTE1_ST2081_10_2160L_6G		0xC0
+#define XST352_BYTE1_ST2081_10_2_1080L_6G	0xC1
+#define XST352_BYTE1_ST2081_10_DL_2160L_6G	0xC2
+#define XST352_BYTE1_ST2082_10_2160L_12G	0xCE
+
+#define XST352_BYTE2_TS_TYPE_MASK		BIT(15)
+#define XST352_BYTE2_TS_TYPE_OFFSET		15
+#define XST352_BYTE2_PIC_TYPE_MASK		BIT(14)
+#define XST352_BYTE2_PIC_TYPE_OFFSET		14
+#define XST352_BYTE2_TS_PIC_TYPE_INTERLACED	0
+#define XST352_BYTE2_TS_PIC_TYPE_PROGRESSIVE	1
+
+#define XST352_BYTE2_FPS_MASK			0xF
+#define XST352_BYTE2_FPS_SHIFT			8
+#define XST352_BYTE2_FPS_96F			0x1
+#define XST352_BYTE2_FPS_24F			0x2
+#define XST352_BYTE2_FPS_24			0x3
+#define XST352_BYTE2_FPS_48F			0x4
+#define XST352_BYTE2_FPS_25			0x5
+#define XST352_BYTE2_FPS_30F			0x6
+#define XST352_BYTE2_FPS_30			0x7
+#define XST352_BYTE2_FPS_48			0x8
+#define XST352_BYTE2_FPS_50			0x9
+#define XST352_BYTE2_FPS_60F			0xA
+#define XST352_BYTE2_FPS_60			0xB
+/* Table 4 ST 2081-10:2015 */
+#define XST352_BYTE2_FPS_96			0xC
+#define XST352_BYTE2_FPS_100			0xD
+#define XST352_BYTE2_FPS_120			0xE
+#define XST352_BYTE2_FPS_120F			0xF
+
+/* Electro Optical Transfer Function Byte 2 bit[5:4] */
+#define XST352_BYTE2_EOTF_MASK			GENMASK(13, 12)
+#define XST352_BYTE2_EOTF_OFFSET		12
+#define XST352_BYTE2_EOTF_SDRTV			0x0
+#define XST352_BYTE2_EOTF_HLG			0x1
+#define XST352_BYTE2_EOTF_SMPTE2084		0x2
+
+#define XST352_BYTE2_COLORIMETRY_MASK		GENMASK(21, 20)
+#define XST352_BYTE2_COLORIMETRY_OFFSET		20
+#define XST352_BYTE2_COLORIMETRY_BT709		0
+#define XST352_BYTE2_COLORIMETRY_VANC		1
+#define XST352_BYTE2_COLORIMETRY_UHDTV		2
+#define XST352_BYTE2_COLORIMETRY_UNKNOWN	3
+
+#define XST352_BYTE3_ACT_LUMA_COUNT_MASK	BIT(22)
+#define XST352_BYTE3_ACT_LUMA_COUNT_OFFSET	22
+
+#define XST352_BYTE3_COLOR_FORMAT_MASK		GENMASK(19, 16)
+#define XST352_BYTE3_COLOR_FORMAT_OFFSET	16
+#define XST352_BYTE3_COLOR_FORMAT_422		0x0
+#define XST352_BYTE3_COLOR_FORMAT_YUV444	0x1
+#define XST352_BYTE3_COLOR_FORMAT_420		0x3
+#define XST352_BYTE3_COLOR_FORMAT_GBR		0x2
+
+#define XST352_BYTE4_BIT_DEPTH_MASK		GENMASK(25, 24)
+#define XST352_BYTE4_BIT_DEPTH_OFFSET		24
+#define XST352_BYTE4_BIT_DEPTH_10		0x1
+#define XST352_BYTE4_BIT_DEPTH_12		0x2
+
+/* Refer Table 3 ST2082-10:2018 */
+#define XST352_BYTE4_LUM_COL_DIFF_MASK		BIT(28)
+
+#define CLK_INT		148500000UL
+
+/**
+ * enum sdi_family_enc - SDI Transport Video Format Detected with Active Pixels
+ * @XSDIRX_SMPTE_ST_274: SMPTE ST 274 detected with AP 1920x1080
+ * @XSDIRX_SMPTE_ST_296: SMPTE ST 296 detected with AP 1280x720
+ * @XSDIRX_SMPTE_ST_2048_2: SMPTE ST 2048-2 detected with AP 2048x1080
+ * @XSDIRX_SMPTE_ST_295: SMPTE ST 295 detected with AP 1920x1080
+ * @XSDIRX_NTSC: NTSC encoding detected with AP 720x486
+ * @XSDIRX_PAL: PAL encoding detected with AP 720x576
+ * @XSDIRX_TS_UNKNOWN: Unknown SMPTE Transport family type
+ */
+enum sdi_family_enc {
+	XSDIRX_SMPTE_ST_274	= 0,
+	XSDIRX_SMPTE_ST_296	= 1,
+	XSDIRX_SMPTE_ST_2048_2	= 2,
+	XSDIRX_SMPTE_ST_295	= 3,
+	XSDIRX_NTSC		= 8,
+	XSDIRX_PAL		= 9,
+	XSDIRX_TS_UNKNOWN	= 15
+};
+
+/**
+ * struct xsdirxss_core - Core configuration SDI Rx Subsystem device structure
+ * @dev: Platform structure
+ * @iomem: Base address of subsystem
+ * @irq: requested irq number
+ * @include_edh: EDH processor presence
+ * @mode: 3G/6G/12G mode
+ * @clks: array of clocks
+ * @num_clks: number of clocks
+ * @rst_gt_gpio: reset gt gpio (fmc init done)
+ * @rst_picxo_gpio: reset picxo core
+ * @bpc: Bits per component, can be 10 or 12
+ */
+struct xsdirxss_core {
+	struct device *dev;
+	void __iomem *iomem;
+	int irq;
+	bool include_edh;
+	int mode;
+	struct clk_bulk_data *clks;
+	int num_clks;
+	struct gpio_desc *rst_gt_gpio;
+	struct gpio_desc *rst_picxo_gpio;
+	u32 bpc;
+};
+
+/**
+ * struct xsdirxss_state - SDI Rx Subsystem device structure
+ * @core: Core structure for MIPI SDI Rx Subsystem
+ * @subdev: The v4l2 subdev structure
+ * @ctrl_handler: control handler
+ * @event: Holds the video unlock event
+ * @format: Active V4L2 format on source pad
+ * @default_format: default V4L2 media bus format
+ * @frame_interval: Captures the frame rate
+ * @vip_format: format information corresponding to the active format
+ * @pad: source media pad
+ * @static_hdr: static hdr payload
+ * @prev_payload: Previous ST352 payload
+ * @vidlockwin: Video lock window value set by control
+ * @edhmask: EDH mask set by control
+ * @searchmask: Search mask set by control
+ * @streaming: Flag for storing streaming state
+ * @vidlocked: Flag indicating SDI Rx has locked onto video stream
+ * @ts_is_interlaced: Flag indicating Transport Stream is interlaced.
+ * @framer_enable: Flag for framer enabled or not set by control
+ *
+ * This structure contains the device driver related parameters
+ */
+struct xsdirxss_state {
+	struct xsdirxss_core core;
+	struct v4l2_subdev subdev;
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_event event;
+	struct v4l2_mbus_framefmt format;
+	struct v4l2_mbus_framefmt default_format;
+	struct v4l2_fract frame_interval;
+	const struct xvip_video_format *vip_format;
+	struct media_pad pad;
+	struct v4l2_hdr10_payload static_hdr;
+	u32 prev_payload;
+	u32 vidlockwin;
+	u32 edhmask;
+	u16 searchmask;
+	bool streaming;
+	bool vidlocked;
+	bool ts_is_interlaced;
+	bool framer_enable;
+};
+
+/* List of clocks required by UHD-SDI Rx subsystem */
+static const char * const xsdirxss_clks[] = {
+	"s_axi_aclk", "sdi_rx_clk", "video_out_clk",
+};
+
+static const u32 xsdirxss_10bpc_mbus_fmts[] = {
+	MEDIA_BUS_FMT_UYVY10_1X20,
+	MEDIA_BUS_FMT_VYYUYY10_4X20,
+	MEDIA_BUS_FMT_VUY10_1X30,
+	MEDIA_BUS_FMT_RBG101010_1X30,
+};
+
+static const u32 xsdirxss_12bpc_mbus_fmts[] = {
+	MEDIA_BUS_FMT_UYVY12_1X24,
+	MEDIA_BUS_FMT_UYYVYY12_4X24,
+	MEDIA_BUS_FMT_VUY12_1X36,
+	MEDIA_BUS_FMT_RBG121212_1X36,
+};
+
+#define XLNX_V4L2_DV_BT_2048X1080P24 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P25 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P30 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 66, 20, 66, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080I48 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 329, 44, 329, 2, 5, 15, 3, 5, 15, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080I50 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 274, 44, 274, 2, 5, 15, 3, 5, 15, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080I60 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		74250000, 66, 20, 66, 2, 5, 15, 3, 5, 15, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_1920X1080P48 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(1920, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 638, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P48 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P50 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P60 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 88, 44, 20, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_3840X2160P48 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(3840, 2160, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		594000000, 1276, 88, 296, 8, 10, 72, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_4096X2160P48 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(4096, 2160, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		594000000, 1020, 88, 296, 8, 10, 72, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_1920X1080I48 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(1920, 1080, 1, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		148500000, 371, 88, 371, 2, 5, 15, 3, 5, 15, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_1920X1080P96 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(1920, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		297000000, 638, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_1920X1080P100 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(1920, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		297000000, 528, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_1920X1080P120 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(1920, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		297000000, 88, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P96 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		297000000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P100 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		297000000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+#define XLNX_V4L2_DV_BT_2048X1080P120 { \
+	.type = V4L2_DV_BT_656_1120, \
+	V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
+		V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
+		297000000, 88, 44, 20, 4, 5, 36, 0, 0, 0, \
+		V4L2_DV_BT_STD_SDI) \
+}
+
+static const struct v4l2_dv_timings fmt_cap[] = {
+	V4L2_DV_BT_SDI_720X487I60,
+	V4L2_DV_BT_CEA_720X576I50,
+	V4L2_DV_BT_CEA_1280X720P24,
+	V4L2_DV_BT_CEA_1280X720P25,
+	V4L2_DV_BT_CEA_1280X720P30,
+	V4L2_DV_BT_CEA_1280X720P50,
+	V4L2_DV_BT_CEA_1280X720P60,
+	V4L2_DV_BT_CEA_1920X1080P24,
+	V4L2_DV_BT_CEA_1920X1080P30,
+	V4L2_DV_BT_CEA_1920X1080I50,
+	V4L2_DV_BT_CEA_1920X1080I60,
+	V4L2_DV_BT_CEA_1920X1080P50,
+	V4L2_DV_BT_CEA_1920X1080P60,
+	V4L2_DV_BT_CEA_3840X2160P24,
+	V4L2_DV_BT_CEA_3840X2160P30,
+	V4L2_DV_BT_CEA_3840X2160P50,
+	V4L2_DV_BT_CEA_3840X2160P60,
+	V4L2_DV_BT_CEA_4096X2160P24,
+	V4L2_DV_BT_CEA_4096X2160P25,
+	V4L2_DV_BT_CEA_4096X2160P30,
+	V4L2_DV_BT_CEA_4096X2160P50,
+	V4L2_DV_BT_CEA_4096X2160P60,
+
+	XLNX_V4L2_DV_BT_2048X1080P24,
+	XLNX_V4L2_DV_BT_2048X1080P25,
+	XLNX_V4L2_DV_BT_2048X1080P30,
+	XLNX_V4L2_DV_BT_2048X1080I48,
+	XLNX_V4L2_DV_BT_2048X1080I50,
+	XLNX_V4L2_DV_BT_2048X1080I60,
+	XLNX_V4L2_DV_BT_2048X1080P48,
+	XLNX_V4L2_DV_BT_2048X1080P50,
+	XLNX_V4L2_DV_BT_2048X1080P60,
+	XLNX_V4L2_DV_BT_1920X1080P48,
+	XLNX_V4L2_DV_BT_1920X1080I48,
+	XLNX_V4L2_DV_BT_3840X2160P48,
+	XLNX_V4L2_DV_BT_4096X2160P48,
+
+	/* HFR */
+	XLNX_V4L2_DV_BT_1920X1080P96,
+	XLNX_V4L2_DV_BT_1920X1080P100,
+	XLNX_V4L2_DV_BT_1920X1080P120,
+	XLNX_V4L2_DV_BT_2048X1080P96,
+	XLNX_V4L2_DV_BT_2048X1080P100,
+	XLNX_V4L2_DV_BT_2048X1080P120,
+};
+
+struct xsdirxss_dv_map {
+	u32 width;
+	u32 height;
+	u32 fps;
+	struct v4l2_dv_timings format;
+};
+
+static const struct xsdirxss_dv_map xsdirxss_dv_timings[] = {
+	/* SD - 720x487i60 */
+	{ 720, 243, 30, V4L2_DV_BT_SDI_720X487I60 },
+	/* SD - 720x576i50 */
+	{ 720, 288, 25, V4L2_DV_BT_CEA_720X576I50 },
+	/* HD - 1280x720p23.98 */
+	/* HD - 1280x720p24 */
+	{ 1280, 720, 24, V4L2_DV_BT_CEA_1280X720P24 },
+	/* HD - 1280x720p25 */
+	{ 1280, 720, 25, V4L2_DV_BT_CEA_1280X720P25 },
+	/* HD - 1280x720p29.97 */
+	/* HD - 1280x720p30 */
+	{ 1280, 720, 30, V4L2_DV_BT_CEA_1280X720P30 },
+	/* HD - 1280x720p50 */
+	{ 1280, 720, 50, V4L2_DV_BT_CEA_1280X720P50 },
+	/* HD - 1280x720p59.94 */
+	/* HD - 1280x720p60 */
+	{ 1280, 720, 60, V4L2_DV_BT_CEA_1280X720P60 },
+	/* HD - 1920x1080p23.98 */
+	/* HD - 1920x1080p24 */
+	{ 1920, 1080, 24, V4L2_DV_BT_CEA_1920X1080P24 },
+	/* HD - 1920x1080p25 */
+	{ 1920, 1080, 25, V4L2_DV_BT_CEA_1920X1080P25 },
+	/* HD - 1920x1080p29.97 */
+	/* HD - 1920x1080p30 */
+	{ 1920, 1080, 30, V4L2_DV_BT_CEA_1920X1080P30 },
+
+	/* HD - 2048x1080p23.98 */
+	/* HD - 2048x1080p24 */
+	{ 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P24 },
+	/* HD - 2048x1080p25 */
+	{ 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P25 },
+	/* HD - 2048x1080p29.97 */
+	/* HD - 2048x1080p30 */
+	{ 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P30 },
+	/* HD - 1920x1080i47.95 */
+	/* HD - 1920x1080i48 */
+	{ 1920, 540, 24, XLNX_V4L2_DV_BT_1920X1080I48 },
+
+	/* HD - 1920x1080i50 */
+	{ 1920, 540, 25, V4L2_DV_BT_CEA_1920X1080I50 },
+	/* HD - 1920x1080i59.94 */
+	/* HD - 1920x1080i60 */
+	{ 1920, 540, 30, V4L2_DV_BT_CEA_1920X1080I60 },
+
+	/* HD - 2048x1080i47.95 */
+	/* HD - 2048x1080i48 */
+	{ 2048, 540, 24, XLNX_V4L2_DV_BT_2048X1080I48 },
+	/* HD - 2048x1080i50 */
+	{ 2048, 540, 25, XLNX_V4L2_DV_BT_2048X1080I50 },
+	/* HD - 2048x1080i59.94 */
+	/* HD - 2048x1080i60 */
+	{ 2048, 540, 30, XLNX_V4L2_DV_BT_2048X1080I60 },
+	/* 3G - 1920x1080p47.95 */
+	/* 3G - 1920x1080p48 */
+	{ 1920, 1080, 48, XLNX_V4L2_DV_BT_1920X1080P48 },
+
+	/* 3G - 1920x1080p50 148.5 */
+	{ 1920, 1080, 50, V4L2_DV_BT_CEA_1920X1080P50 },
+	/* 3G - 1920x1080p59.94 148.5/1.001 */
+	/* 3G - 1920x1080p60 148.5 */
+	{ 1920, 1080, 60, V4L2_DV_BT_CEA_1920X1080P60 },
+
+	/* 3G - 2048x1080p47.95 */
+	/* 3G - 2048x1080p48 */
+	{ 2048, 1080, 48, XLNX_V4L2_DV_BT_2048X1080P48 },
+	/* 3G - 2048x1080p50 */
+	{ 2048, 1080, 50, XLNX_V4L2_DV_BT_2048X1080P50 },
+	/* 3G - 2048x1080p59.94 */
+	/* 3G - 2048x1080p60 */
+	{ 2048, 1080, 60, XLNX_V4L2_DV_BT_2048X1080P60 },
+
+	/* 6G - 3840X2160p23.98 */
+	/* 6G - 3840X2160p24 */
+	{ 3840, 2160, 24, V4L2_DV_BT_CEA_3840X2160P24 },
+	/* 6G - 3840X2160p25 */
+	{ 3840, 2160, 25, V4L2_DV_BT_CEA_3840X2160P25 },
+	/* 6G - 3840X2160p29.97 */
+	/* 6G - 3840X2160p30 */
+	{ 3840, 2160, 30, V4L2_DV_BT_CEA_3840X2160P30 },
+	/* 6G - 4096X2160p23.98 */
+	/* 6G - 4096X2160p24 */
+	{ 4096, 2160, 24, V4L2_DV_BT_CEA_4096X2160P24 },
+	/* 6G - 4096X2160p25 */
+	{ 4096, 2160, 25, V4L2_DV_BT_CEA_4096X2160P25 },
+	/* 6G - 4096X2160p29.97 */
+	/* 6G - 4096X2160p30 */
+	{ 4096, 2160, 30, V4L2_DV_BT_CEA_4096X2160P30 },
+	/* 12G - 3840X2160p47.95 */
+	/* 12G - 3840X2160p48 */
+	{ 3840, 2160, 48, XLNX_V4L2_DV_BT_3840X2160P48 },
+
+	/* 12G - 3840X2160p50 */
+	{ 3840, 2160, 50, V4L2_DV_BT_CEA_3840X2160P50 },
+	/* 12G - 3840X2160p59.94 */
+	/* 12G - 3840X2160p60 */
+	{ 3840, 2160, 60, V4L2_DV_BT_CEA_3840X2160P60 },
+
+	/* 12G - 4096X2160p47.95 */
+	/* 12G - 4096X2160p48 */
+	{ 3840, 2160, 48, XLNX_V4L2_DV_BT_4096X2160P48 },
+
+	/* 12G - 4096X2160p50 */
+	{ 4096, 2160, 50, V4L2_DV_BT_CEA_4096X2160P50 },
+	/* 12G - 4096X2160p59.94 */
+	/* 12G - 4096X2160p60 */
+	{ 4096, 2160, 60, V4L2_DV_BT_CEA_4096X2160P60 },
+
+	/* 6G/12G HFR */
+	{ 1920, 1080, 96, XLNX_V4L2_DV_BT_1920X1080P96 },
+	{ 1920, 1080, 100, XLNX_V4L2_DV_BT_1920X1080P100 },
+	{ 1920, 1080, 120, XLNX_V4L2_DV_BT_1920X1080P120 },
+	{ 2048, 1080, 96, XLNX_V4L2_DV_BT_2048X1080P96 },
+	{ 2048, 1080, 100, XLNX_V4L2_DV_BT_2048X1080P100 },
+	{ 2048, 1080, 120, XLNX_V4L2_DV_BT_2048X1080P120 },
+};
+
+static inline struct xsdirxss_state *
+to_xsdirxssstate(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xsdirxss_state, subdev);
+}
+
+/*
+ * Register related operations
+ */
+static inline u32 xsdirxss_read(struct xsdirxss_core *xsdirxss, u32 addr)
+{
+	return ioread32(xsdirxss->iomem + addr);
+}
+
+static inline void xsdirxss_write(struct xsdirxss_core *xsdirxss, u32 addr,
+				  u32 value)
+{
+	iowrite32(value, xsdirxss->iomem + addr);
+}
+
+static inline void xsdirxss_clr(struct xsdirxss_core *xsdirxss, u32 addr,
+				u32 clr)
+{
+	xsdirxss_write(xsdirxss, addr, xsdirxss_read(xsdirxss, addr) & ~clr);
+}
+
+static inline void xsdirxss_set(struct xsdirxss_core *xsdirxss, u32 addr,
+				u32 set)
+{
+	xsdirxss_write(xsdirxss, addr, xsdirxss_read(xsdirxss, addr) | set);
+}
+
+static inline void xsdirx_core_disable(struct xsdirxss_core *core)
+{
+	xsdirxss_clr(core, XSDIRX_RST_CTRL_REG, XSDIRX_RST_CTRL_SS_EN_MASK);
+}
+
+static inline void xsdirx_core_enable(struct xsdirxss_core *core)
+{
+	xsdirxss_set(core, XSDIRX_RST_CTRL_REG, XSDIRX_RST_CTRL_SS_EN_MASK);
+}
+
+static void xsdirxss_gt_reset(struct xsdirxss_core *core)
+{
+	/* reset qpll0 */
+	gpiod_set_value(core->rst_gt_gpio, 0x1);
+	gpiod_set_value(core->rst_gt_gpio, 0x0);
+	/* reset picxo core */
+	gpiod_set_value(core->rst_picxo_gpio, 0x1);
+	gpiod_set_value(core->rst_picxo_gpio, 0x0);
+}
+
+static int xsdirx_set_modedetect(struct xsdirxss_core *core, u16 mask)
+{
+	u32 i, val;
+
+	mask &= XSDIRX_DETECT_ALL_MODES;
+	if (!mask) {
+		dev_err(core->dev, "Invalid bit mask = 0x%08x\n", mask);
+		return -EINVAL;
+	}
+
+	dev_dbg(core->dev, "mask = 0x%x\n", mask);
+
+	val = xsdirxss_read(core, XSDIRX_MDL_CTRL_REG);
+	val &= ~XSDIRX_MDL_CTRL_MODE_DET_EN_MASK;
+	val &= ~XSDIRX_MDL_CTRL_MODE_AUTO_DET_MASK;
+	val &= ~XSDIRX_MDL_CTRL_FORCED_MODE_MASK;
+
+	if (hweight16(mask) > 1) {
+		/* Multi mode detection as more than 1 bit set in mask */
+		dev_dbg(core->dev, "Detect multiple modes\n");
+		for (i = 0; i < XSDIRX_MODE_NUM_SUPPORTED; i++) {
+			switch (mask & (1 << i)) {
+			case BIT(XSDIRX_MODE_SD_OFFSET):
+				val |= XSDIRX_MDL_CTRL_MODE_SD_EN_MASK;
+				break;
+			case BIT(XSDIRX_MODE_HD_OFFSET):
+				val |= XSDIRX_MDL_CTRL_MODE_HD_EN_MASK;
+				break;
+			case BIT(XSDIRX_MODE_3G_OFFSET):
+				val |= XSDIRX_MDL_CTRL_MODE_3G_EN_MASK;
+				break;
+			case BIT(XSDIRX_MODE_6G_OFFSET):
+				val |= XSDIRX_MDL_CTRL_MODE_6G_EN_MASK;
+				break;
+			case BIT(XSDIRX_MODE_12GI_OFFSET):
+				val |= XSDIRX_MDL_CTRL_MODE_12GI_EN_MASK;
+				break;
+			case BIT(XSDIRX_MODE_12GF_OFFSET):
+				val |= XSDIRX_MDL_CTRL_MODE_12GF_EN_MASK;
+				break;
+			}
+		}
+		val |= XSDIRX_MDL_CTRL_MODE_DET_EN_MASK;
+	} else {
+		/* Fixed Mode */
+		u32 forced_mode_mask;
+
+		dev_dbg(core->dev, "Detect fixed mode\n");
+
+		/* Find offset of first bit set */
+		switch (__ffs(mask)) {
+		case XSDIRX_MODE_SD_OFFSET:
+			forced_mode_mask = XSDIRX_MODE_SD_MASK;
+			break;
+		case XSDIRX_MODE_HD_OFFSET:
+			forced_mode_mask = XSDIRX_MODE_HD_MASK;
+			break;
+		case XSDIRX_MODE_3G_OFFSET:
+			forced_mode_mask = XSDIRX_MODE_3G_MASK;
+			break;
+		case XSDIRX_MODE_6G_OFFSET:
+			forced_mode_mask = XSDIRX_MODE_6G_MASK;
+			break;
+		case XSDIRX_MODE_12GI_OFFSET:
+			forced_mode_mask = XSDIRX_MODE_12GI_MASK;
+			break;
+		case XSDIRX_MODE_12GF_OFFSET:
+			forced_mode_mask = XSDIRX_MODE_12GF_MASK;
+			break;
+		default:
+			forced_mode_mask = 0;
+		}
+		dev_dbg(core->dev, "Forced Mode Mask : 0x%x\n",
+			forced_mode_mask);
+		val |= forced_mode_mask << XSDIRX_MDL_CTRL_FORCED_MODE_OFFSET;
+	}
+
+	dev_dbg(core->dev, "Modes to be detected : sdi ctrl reg = 0x%08x\n",
+		val);
+	xsdirxss_write(core, XSDIRX_MDL_CTRL_REG, val);
+
+	return 0;
+}
+
+static void xsdirx_framer(struct xsdirxss_core *core, bool flag)
+{
+	if (flag)
+		xsdirxss_set(core, XSDIRX_MDL_CTRL_REG,
+			     XSDIRX_MDL_CTRL_FRM_EN_MASK);
+	else
+		xsdirxss_clr(core, XSDIRX_MDL_CTRL_REG,
+			     XSDIRX_MDL_CTRL_FRM_EN_MASK);
+}
+
+static void xsdirx_setedherrcnttrigger(struct xsdirxss_core *core, u32 enable)
+{
+	u32 val;
+
+	val = enable & XSDIRX_EDH_ALLERR_MASK;
+
+	xsdirxss_write(core, XSDIRX_EDH_ERRCNT_EN_REG, val);
+}
+
+static inline void xsdirx_setvidlockwindow(struct xsdirxss_core *core, u32 val)
+{
+	/*
+	 * The video lock window is the amount of time for which
+	 * the mode and transport stream should be locked to get
+	 * the video lock interrupt.
+	 */
+	xsdirxss_write(core, XSDIRX_VID_LOCK_WINDOW_REG, val);
+}
+
+static inline void xsdirx_disableintr(struct xsdirxss_core *core, u32 mask)
+{
+	xsdirxss_clr(core, XSDIRX_IER_REG, mask);
+}
+
+static inline void xsdirx_enableintr(struct xsdirxss_core *core, u32 mask)
+{
+	xsdirxss_set(core, XSDIRX_IER_REG, mask);
+}
+
+static void xsdirx_globalintr(struct xsdirxss_core *core, bool flag)
+{
+	if (flag)
+		xsdirxss_set(core, XSDIRX_GLBL_IER_REG,
+			     XSDIRX_GLBL_INTR_EN_MASK);
+	else
+		xsdirxss_clr(core, XSDIRX_GLBL_IER_REG,
+			     XSDIRX_GLBL_INTR_EN_MASK);
+}
+
+static inline void xsdirx_clearintr(struct xsdirxss_core *core, u32 mask)
+{
+	xsdirxss_set(core, XSDIRX_ISR_REG, mask);
+}
+
+static void xsdirx_vid_bridge_control(struct xsdirxss_core *core,
+				      bool enable)
+{
+	struct xsdirxss_state *state =
+		container_of(core, struct xsdirxss_state, core);
+	u32 mask = XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK;
+
+	if (state->format.code == MEDIA_BUS_FMT_VUY10_1X30 ||
+	    state->format.code == MEDIA_BUS_FMT_RBG101010_1X30 ||
+	    state->format.code == MEDIA_BUS_FMT_RBG121212_1X36 ||
+	    state->format.code == MEDIA_BUS_FMT_VUY12_1X36)
+		mask |= (XSDIRX_RST_CTRL_BRIDGE_CH_FMT_YUV444 <<
+			 XSDIRX_RST_CTRL_BRIDGE_CH_FMT_OFFSET);
+
+	if (enable)
+		xsdirxss_set(core, XSDIRX_RST_CTRL_REG, mask);
+	else
+		xsdirxss_clr(core, XSDIRX_RST_CTRL_REG, mask);
+}
+
+static void xsdirx_axis4_bridge_control(struct xsdirxss_core *core,
+					bool enable)
+{
+	if (enable)
+		xsdirxss_set(core, XSDIRX_RST_CTRL_REG,
+			     XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK);
+	else
+		xsdirxss_clr(core, XSDIRX_RST_CTRL_REG,
+			     XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK);
+}
+
+static void xsdirx_streamflow_control(struct xsdirxss_core *core, bool enable)
+{
+	/* The sdi to native bridge is followed by native to axis4 bridge */
+	if (enable) {
+		xsdirx_axis4_bridge_control(core, enable);
+		xsdirx_vid_bridge_control(core, enable);
+	} else {
+		xsdirx_vid_bridge_control(core, enable);
+		xsdirx_axis4_bridge_control(core, enable);
+	}
+}
+
+static void xsdirxss_get_framerate(struct v4l2_fract *frame_interval,
+				   u32 framerate)
+{
+	switch (framerate) {
+	case XSDIRX_TS_DET_STAT_RATE_23_98HZ:
+		frame_interval->numerator = 1001;
+		frame_interval->denominator = 24000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_24HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 24000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_25HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 25000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_29_97HZ:
+		frame_interval->numerator = 1001;
+		frame_interval->denominator = 30000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_30HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 30000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_47_95HZ:
+		frame_interval->numerator = 1001;
+		frame_interval->denominator = 48000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_48HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 48000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_50HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 50000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_59_94HZ:
+		frame_interval->numerator = 1001;
+		frame_interval->denominator = 60000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_60HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 60000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_95_90HZ:
+		frame_interval->numerator = 1001;
+		frame_interval->denominator = 96000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_96HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 96000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_100HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 100000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_119_88HZ:
+		frame_interval->numerator = 1001;
+		frame_interval->denominator = 120000;
+		break;
+	case XSDIRX_TS_DET_STAT_RATE_120HZ:
+		frame_interval->numerator = 1000;
+		frame_interval->denominator = 120000;
+		break;
+	default:
+		frame_interval->numerator = 1;
+		frame_interval->denominator = 1;
+	}
+}
+
+static void xsdirxss_set_gtclk(struct xsdirxss_state *state)
+{
+	struct clk *gtclk;
+	unsigned long clkrate;
+	int ret, is_frac;
+	struct xsdirxss_core *core = &state->core;
+	u32 mode;
+
+	mode = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+	mode &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
+
+	xsdirx_core_disable(core);
+	xsdirx_globalintr(core, false);
+	xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
+
+	/* get sdi_rx_clk */
+	gtclk = core->clks[1].clk;
+	is_frac = state->frame_interval.numerator == 1001 ? 1 : 0;
+
+	/*
+	 * PLL ref clock is 148.5MHz for integer frame rates
+	 * and 148.35MHz for fractional frame rates.
+	 * For SD mode its always 148.5MHz for integer & fractional.
+	 * Please refer to Table 5-2 in PG290
+	 * https://www.xilinx.com/support/documentation/ip_documentation/v_smpte_uhdsdi_rx_ss/v2_0/pg290-v-smpte-uhdsdi-rx-ss.pdf
+	 */
+	if (!is_frac || mode == XSDIRX_MODE_SD_MASK)
+		clkrate = CLK_INT;
+	else
+		clkrate = (CLK_INT * 1000) / 1001;
+
+	ret = clk_set_rate(gtclk, clkrate);
+	if (ret)
+		dev_err(core->dev, "failed to set clk rate = %d\n", ret);
+
+	/* reset qpll0 and picxo core */
+	xsdirxss_gt_reset(core);
+
+	clkrate = clk_get_rate(gtclk);
+
+	dev_dbg(core->dev, "clkrate = %lu is_frac = %d\n",
+		clkrate, is_frac);
+
+	xsdirx_framer(core, state->framer_enable);
+	xsdirx_setedherrcnttrigger(core, state->edhmask);
+	xsdirx_setvidlockwindow(core, state->vidlockwin);
+	xsdirx_set_modedetect(core, state->searchmask);
+	xsdirx_enableintr(core, XSDIRX_INTR_ALL_MASK);
+	xsdirx_globalintr(core, true);
+	xsdirx_core_enable(core);
+}
+
+/**
+ * xsdirx_get_stream_properties - Get SDI Rx stream properties
+ * @state: pointer to driver state
+ *
+ * This function decodes the stream's ST352 payload (if available) to get
+ * stream properties like width, height, picture type (interlaced/progressive),
+ * etc.
+ *
+ * Return: 0 for success else errors
+ */
+static int xsdirx_get_stream_properties(struct xsdirxss_state *state)
+{
+	struct xsdirxss_core *core = &state->core;
+	u32 mode, payload = 0, val, family, valid, tscan;
+	u8 byte1 = 0, active_luma = 0, pic_type = 0, framerate = 0;
+	u8 sampling = XST352_BYTE3_COLOR_FORMAT_422;
+	struct v4l2_mbus_framefmt *format = &state->format;
+	u32 bpc = XST352_BYTE4_BIT_DEPTH_10;
+
+	mode = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+	mode &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
+
+	valid = xsdirxss_read(core, XSDIRX_ST352_VALID_REG);
+
+	if (mode >= XSDIRX_MODE_3G_MASK && !valid) {
+		dev_err_ratelimited(core->dev, "No valid ST352 payload present even for 3G mode and above\n");
+		return -EINVAL;
+	}
+
+	val = xsdirxss_read(core, XSDIRX_TS_DET_STAT_REG);
+	if (valid & XSDIRX_ST352_VALID_DS1_MASK) {
+		payload = xsdirxss_read(core, XSDIRX_ST352_DS1_REG);
+		byte1 = (payload >> XST352_PAYLOAD_BYTE1_SHIFT) &
+				XST352_PAYLOAD_BYTE_MASK;
+		active_luma = (payload & XST352_BYTE3_ACT_LUMA_COUNT_MASK) >>
+				XST352_BYTE3_ACT_LUMA_COUNT_OFFSET;
+		pic_type = (payload & XST352_BYTE2_PIC_TYPE_MASK) >>
+				XST352_BYTE2_PIC_TYPE_OFFSET;
+		framerate = (payload >> XST352_BYTE2_FPS_SHIFT) &
+				XST352_BYTE2_FPS_MASK;
+		tscan = (payload & XST352_BYTE2_TS_TYPE_MASK) >>
+				XST352_BYTE2_TS_TYPE_OFFSET;
+		sampling = (payload & XST352_BYTE3_COLOR_FORMAT_MASK) >>
+			   XST352_BYTE3_COLOR_FORMAT_OFFSET;
+		bpc = (payload & XST352_BYTE4_BIT_DEPTH_MASK) >>
+			XST352_BYTE4_BIT_DEPTH_OFFSET;
+	} else {
+		dev_dbg(core->dev, "No ST352 payload available : Mode = %d\n",
+			mode);
+		framerate = (val & XSDIRX_TS_DET_STAT_RATE_MASK) >>
+				XSDIRX_TS_DET_STAT_RATE_OFFSET;
+		tscan = (val & XSDIRX_TS_DET_STAT_SCAN_MASK) >>
+				XSDIRX_TS_DET_STAT_SCAN_OFFSET;
+	}
+
+	if ((bpc == XST352_BYTE4_BIT_DEPTH_10 && core->bpc != 10) ||
+	    (bpc == XST352_BYTE4_BIT_DEPTH_12 && core->bpc != 12)) {
+		dev_dbg(core->dev, "Bit depth not supported. bpc = %d core->bpc = %d\n",
+			bpc, core->bpc);
+		return -EINVAL;
+	}
+
+	family = (val & XSDIRX_TS_DET_STAT_FAMILY_MASK) >>
+			XSDIRX_TS_DET_STAT_FAMILY_OFFSET;
+	state->ts_is_interlaced = tscan ? false : true;
+
+	dev_dbg(core->dev, "ts_is_interlaced = %d, family = %d\n",
+		state->ts_is_interlaced, family);
+
+	switch (mode) {
+	case XSDIRX_MODE_HD_MASK:
+		if (!valid) {
+			/* No payload obtained */
+			dev_dbg(core->dev, "frame rate : %d, tscan = %d\n",
+				framerate, tscan);
+			/*
+			 * NOTE : A progressive segmented frame pSF will be
+			 * reported incorrectly as Interlaced as we rely on IP's
+			 * transport scan locked bit.
+			 */
+			dev_warn(core->dev, "pSF will be incorrectly reported as Interlaced\n");
+
+			switch (framerate) {
+			case XSDIRX_TS_DET_STAT_RATE_23_98HZ:
+			case XSDIRX_TS_DET_STAT_RATE_24HZ:
+			case XSDIRX_TS_DET_STAT_RATE_25HZ:
+			case XSDIRX_TS_DET_STAT_RATE_29_97HZ:
+			case XSDIRX_TS_DET_STAT_RATE_30HZ:
+				if (family == XSDIRX_SMPTE_ST_296) {
+					format->width = 1280;
+					format->height = 720;
+					format->field = V4L2_FIELD_NONE;
+				} else if (family == XSDIRX_SMPTE_ST_2048_2) {
+					format->width = 2048;
+					format->height = 1080;
+					if (tscan)
+						format->field = V4L2_FIELD_NONE;
+					else
+						format->field =
+							V4L2_FIELD_ALTERNATE;
+				} else {
+					format->width = 1920;
+					format->height = 1080;
+					if (tscan)
+						format->field = V4L2_FIELD_NONE;
+					else
+						format->field =
+							V4L2_FIELD_ALTERNATE;
+				}
+				break;
+			case XSDIRX_TS_DET_STAT_RATE_50HZ:
+			case XSDIRX_TS_DET_STAT_RATE_59_94HZ:
+			case XSDIRX_TS_DET_STAT_RATE_60HZ:
+				if (family == XSDIRX_SMPTE_ST_274) {
+					format->width = 1920;
+					format->height = 1080;
+				} else {
+					format->width = 1280;
+					format->height = 720;
+				}
+				format->field = V4L2_FIELD_NONE;
+				break;
+			default:
+				format->width = 1920;
+				format->height = 1080;
+				format->field = V4L2_FIELD_NONE;
+			}
+		} else {
+			dev_dbg(core->dev, "Got the payload\n");
+			switch (byte1) {
+			case XST352_BYTE1_ST292_1x720L_1_5G:
+				/* SMPTE ST 292-1 for 720 line payloads */
+				format->width = 1280;
+				format->height = 720;
+				break;
+			case XST352_BYTE1_ST292_1x1080L_1_5G:
+				/* SMPTE ST 292-1 for 1080 line payloads */
+				format->height = 1080;
+				if (active_luma)
+					format->width = 2048;
+				else
+					format->width = 1920;
+				break;
+			default:
+				dev_dbg(core->dev, "Unknown HD Mode SMPTE standard\n");
+				return -EINVAL;
+			}
+		}
+		break;
+	case XSDIRX_MODE_SD_MASK:
+		format->field = V4L2_FIELD_ALTERNATE;
+
+		switch (family) {
+		case XSDIRX_NTSC:
+			format->width = 720;
+			format->height = 486;
+			break;
+		case XSDIRX_PAL:
+			format->width = 720;
+			format->height = 576;
+			break;
+		default:
+			dev_dbg(core->dev, "Unknown SD Mode SMPTE standard\n");
+			return -EINVAL;
+		}
+		break;
+	case XSDIRX_MODE_3G_MASK:
+		switch (byte1) {
+		case XST352_BYTE1_ST425_2008_750L_3GB:
+			/* Sec 4.1.6.1 SMPTE 425-2008 */
+		case XST352_BYTE1_ST372_2x720L_3GB:
+			/* Table 13 SMPTE 425-2008 */
+			format->width = 1280;
+			format->height = 720;
+			break;
+		case XST352_BYTE1_ST425_2008_1125L_3GA:
+			/* ST352 Table SMPTE 425-1 */
+		case XST352_BYTE1_ST372_DL_3GB:
+			/* Table 13 SMPTE 425-2008 */
+		case XST352_BYTE1_ST372_2x1080L_3GB:
+			/* Table 13 SMPTE 425-2008 */
+			format->height = 1080;
+			if (active_luma)
+				format->width = 2048;
+			else
+				format->width = 1920;
+			break;
+		default:
+			dev_dbg(core->dev, "Unknown 3G Mode SMPTE standard\n");
+			return -EINVAL;
+		}
+		break;
+	case XSDIRX_MODE_6G_MASK:
+		switch (byte1) {
+		case XST352_BYTE1_ST2081_10_DL_2160L_6G:
+			/* Dual link 6G */
+		case XST352_BYTE1_ST2081_10_2160L_6G:
+			/* Table 3 SMPTE ST 2081-10 */
+			format->height = 2160;
+			if (active_luma)
+				format->width = 4096;
+			else
+				format->width = 3840;
+			break;
+		case XST352_BYTE1_ST2081_10_2_1080L_6G:
+			format->height = 1080;
+			if (active_luma)
+				format->width = 2048;
+			else
+				format->width = 1920;
+			break;
+		default:
+			dev_dbg(core->dev, "Unknown 6G Mode SMPTE standard\n");
+			return -EINVAL;
+		}
+		break;
+	case XSDIRX_MODE_12GI_MASK:
+	case XSDIRX_MODE_12GF_MASK:
+		switch (byte1) {
+		case XST352_BYTE1_ST2082_10_2160L_12G:
+			/* Section 4.3.1 SMPTE ST 2082-10 */
+			format->height = 2160;
+			if (active_luma)
+				format->width = 4096;
+			else
+				format->width = 3840;
+			break;
+		default:
+			dev_dbg(core->dev, "Unknown 12G Mode SMPTE standard\n");
+			return -EINVAL;
+		}
+		break;
+	default:
+		dev_err(core->dev, "Invalid Mode\n");
+		return -EINVAL;
+	}
+
+	if (valid) {
+		if (pic_type)
+			format->field = V4L2_FIELD_NONE;
+		else
+			format->field = V4L2_FIELD_ALTERNATE;
+
+		if (format->height == 1080 && pic_type && !tscan)
+			format->field = V4L2_FIELD_ALTERNATE;
+
+		if (byte1 == XST352_BYTE1_ST372_DL_3GB) {
+			if (!pic_type)
+				format->field = V4L2_FIELD_ALTERNATE;
+			else
+				format->field = V4L2_FIELD_NONE;
+		}
+	}
+
+	if (format->field == V4L2_FIELD_ALTERNATE)
+		format->height = format->height / 2;
+
+	switch (sampling) {
+	case XST352_BYTE3_COLOR_FORMAT_420:
+		if (core->bpc == 10)
+			format->code = MEDIA_BUS_FMT_VYYUYY10_4X20;
+		else
+			format->code = MEDIA_BUS_FMT_UYYVYY12_4X24;
+		break;
+	case XST352_BYTE3_COLOR_FORMAT_422:
+		if (core->bpc == 10)
+			format->code = MEDIA_BUS_FMT_UYVY10_1X20;
+		else
+			format->code = MEDIA_BUS_FMT_UYVY12_1X24;
+		break;
+	case XST352_BYTE3_COLOR_FORMAT_YUV444:
+		if (core->bpc == 10)
+			format->code = MEDIA_BUS_FMT_VUY10_1X30;
+		else
+			format->code = MEDIA_BUS_FMT_VUY12_1X36;
+		break;
+	case XST352_BYTE3_COLOR_FORMAT_GBR:
+		if (core->bpc == 10)
+			format->code = MEDIA_BUS_FMT_RBG101010_1X30;
+		else
+			format->code = MEDIA_BUS_FMT_RBG121212_1X36;
+		break;
+	default:
+		dev_err(core->dev, "Unsupported color format : %d\n", sampling);
+		return -EINVAL;
+	}
+
+	xsdirxss_get_framerate(&state->frame_interval, framerate);
+
+	memset(&state->static_hdr, 0, sizeof(state->static_hdr));
+
+	state->static_hdr.eotf = V4L2_EOTF_TRADITIONAL_GAMMA_SDR;
+	format->colorspace = V4L2_COLORSPACE_SMPTE170M;
+	format->xfer_func = V4L2_XFER_FUNC_709;
+	format->ycbcr_enc = V4L2_YCBCR_ENC_601;
+	format->quantization = V4L2_QUANTIZATION_LIM_RANGE;
+
+	if (mode != XSDIRX_MODE_SD_MASK) {
+		u8 eotf = (payload & XST352_BYTE2_EOTF_MASK) >>
+			XST352_BYTE2_EOTF_OFFSET;
+
+		u8 colorimetry = (payload & XST352_BYTE2_COLORIMETRY_MASK) >>
+			XST352_BYTE2_COLORIMETRY_OFFSET;
+
+		/*
+		 * Bit 7 and 4 of byte 3 form the colorimetry field for HD.
+		 * Checkout SMPTE 292-1:2018 Sec 9.5 for details
+		 */
+		if (mode == XSDIRX_MODE_HD_MASK ||
+		    byte1 == XST352_BYTE1_ST372_DL_3GB) {
+			/* For case when there might be no payload */
+			colorimetry = XST352_BYTE2_COLORIMETRY_BT709;
+
+			if (valid & XSDIRX_ST352_VALID_DS1_MASK) {
+				colorimetry = (FIELD_GET(BIT(23), payload) << 1) |
+					FIELD_GET(BIT(20), payload);
+			}
+		}
+
+		/* Get the EOTF function */
+		switch (eotf) {
+		case XST352_BYTE2_EOTF_SDRTV:
+			state->static_hdr.eotf =
+				V4L2_EOTF_TRADITIONAL_GAMMA_SDR;
+			break;
+		case XST352_BYTE2_EOTF_SMPTE2084:
+			state->static_hdr.eotf = V4L2_EOTF_SMPTE_ST2084;
+			format->xfer_func = V4L2_XFER_FUNC_SMPTE2084;
+			break;
+		case XST352_BYTE2_EOTF_HLG:
+			state->static_hdr.eotf = V4L2_EOTF_BT_2100_HLG;
+			format->xfer_func = V4L2_XFER_FUNC_HLG;
+			break;
+		}
+
+		/* Get the colorimetry data */
+		switch (colorimetry) {
+		case XST352_BYTE2_COLORIMETRY_BT709:
+			format->colorspace = V4L2_COLORSPACE_REC709;
+			format->ycbcr_enc = V4L2_YCBCR_ENC_709;
+			break;
+		case XST352_BYTE2_COLORIMETRY_UHDTV:
+			format->colorspace = V4L2_COLORSPACE_BT2020;
+			format->ycbcr_enc = V4L2_YCBCR_ENC_BT2020;
+			break;
+		default:
+			/*
+			 * Modes which will have VANC and Unknown colorimetery
+			 * are currently not supported
+			 */
+			format->colorspace = V4L2_COLORSPACE_DEFAULT;
+			format->xfer_func = V4L2_XFER_FUNC_DEFAULT;
+			break;
+		}
+	}
+
+	/* Refer to Table 3 ST 2082-10:2018 */
+	if (mode == XSDIRX_MODE_12GI_OFFSET ||
+	    mode == XSDIRX_MODE_12GF_OFFSET) {
+		switch (sampling) {
+		case XST352_BYTE3_COLOR_FORMAT_420:
+		case XST352_BYTE3_COLOR_FORMAT_422:
+		case XST352_BYTE3_COLOR_FORMAT_YUV444:
+			if (payload & XST352_BYTE4_LUM_COL_DIFF_MASK)
+				format->ycbcr_enc =
+					V4L2_YCBCR_ENC_BT2020_CONST_LUM;
+			else
+				format->ycbcr_enc =
+					V4L2_YCBCR_ENC_BT2020;
+		}
+	}
+
+	/* Set quantization range */
+	if (sampling == XST352_BYTE3_COLOR_FORMAT_GBR &&
+	    format->colorspace != V4L2_COLORSPACE_BT2020)
+		format->quantization = V4L2_QUANTIZATION_FULL_RANGE;
+
+	/*
+	 * Save the payload to be used in vsync interrupt to check for
+	 * change in payload without video lock/unlock sequence
+	 */
+	if (valid & XSDIRX_ST352_VALID_DS1_MASK)
+		state->prev_payload = payload;
+
+	dev_dbg(core->dev, "Stream width = %d height = %d Field = %d payload = 0x%08x ts = 0x%08x\n",
+		format->width, format->height, format->field, payload, val);
+	dev_dbg(core->dev, "frame rate numerator = %d denominator = %d\n",
+		state->frame_interval.numerator,
+		state->frame_interval.denominator);
+	dev_dbg(core->dev, "Stream code = 0x%x\n", format->code);
+	return 0;
+}
+
+/**
+ * xsdirxss_irq_handler - Interrupt handler for SDI Rx
+ * @irq: IRQ number
+ * @dev_id: Pointer to device state
+ *
+ * The SDI Rx interrupts are cleared by writing 1 to corresponding bit.
+ *
+ * Return: IRQ_HANDLED after handling interrupts
+ */
+static irqreturn_t xsdirxss_irq_handler(int irq, void *dev_id)
+{
+	struct xsdirxss_state *state = (struct xsdirxss_state *)dev_id;
+	struct xsdirxss_core *core = &state->core;
+	u32 status;
+
+	status = xsdirxss_read(core, XSDIRX_ISR_REG);
+	dev_dbg(core->dev, "interrupt status = 0x%08x\n", status);
+
+	if (!status)
+		return IRQ_NONE;
+
+	xsdirxss_write(core, XSDIRX_ISR_REG, status);
+
+	if (status & XSDIRX_INTR_VIDLOCK_MASK ||
+	    status & XSDIRX_INTR_VIDUNLOCK_MASK) {
+		u32 val1, val2;
+		bool gen_event = true;
+
+		dev_dbg(core->dev, "video lock/unlock interrupt\n");
+
+		xsdirx_streamflow_control(core, false);
+		state->streaming = false;
+
+		val1 = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+		val2 = xsdirxss_read(core, XSDIRX_TS_DET_STAT_REG);
+
+		if ((val1 & XSDIRX_MODE_DET_STAT_MODE_LOCK_MASK) &&
+		    (val2 & XSDIRX_TS_DET_STAT_LOCKED_MASK)) {
+			u32 mask = XSDIRX_RST_CTRL_RST_CRC_ERRCNT_MASK |
+				   XSDIRX_RST_CTRL_RST_EDH_ERRCNT_MASK;
+
+			dev_dbg(core->dev, "video lock interrupt\n");
+
+			xsdirxss_set(core, XSDIRX_RST_CTRL_REG, mask);
+			xsdirxss_clr(core, XSDIRX_RST_CTRL_REG, mask);
+
+			val1 = xsdirxss_read(core, XSDIRX_ST352_VALID_REG);
+			val2 = xsdirxss_read(core, XSDIRX_ST352_DS1_REG);
+
+			dev_dbg(core->dev, "valid st352 mask = 0x%08x\n", val1);
+			dev_dbg(core->dev, "st352 payload = 0x%08x\n", val2);
+
+			if (state->vidlocked) {
+				gen_event = false;
+			} else if (!xsdirx_get_stream_properties(state)) {
+				state->vidlocked = true;
+				xsdirxss_set_gtclk(state);
+			} else {
+				dev_err_ratelimited(core->dev, "Unable to get stream properties!\n");
+				state->vidlocked = false;
+			}
+
+		} else {
+			dev_dbg(core->dev, "video unlock interrupt\n");
+			state->vidlocked = false;
+		}
+		if (gen_event) {
+			memset(&state->event, 0, sizeof(state->event));
+			state->event.type = V4L2_EVENT_SOURCE_CHANGE;
+			state->event.u.src_change.changes =
+				V4L2_EVENT_SRC_CH_RESOLUTION;
+			v4l2_subdev_notify_event(&state->subdev, &state->event);
+		}
+	}
+
+	if (status & XSDIRX_INTR_UNDERFLOW_MASK) {
+		dev_dbg(core->dev, "Video in to AXI4 Stream core underflow interrupt\n");
+
+		memset(&state->event, 0, sizeof(state->event));
+		state->event.type = V4L2_EVENT_XLNXSDIRX_UNDERFLOW;
+		v4l2_subdev_notify_event(&state->subdev, &state->event);
+	}
+
+	if (status & XSDIRX_INTR_OVERFLOW_MASK) {
+		dev_dbg(core->dev, "Video in to AXI4 Stream core overflow interrupt\n");
+
+		memset(&state->event, 0, sizeof(state->event));
+		state->event.type = V4L2_EVENT_XLNXSDIRX_OVERFLOW;
+		v4l2_subdev_notify_event(&state->subdev, &state->event);
+	}
+
+	if (status & XSDIRX_INTR_VSYNC_MASK) {
+		u32 valid, payload;
+		/*
+		 * If ST352 payload changed without generating video unlock/
+		 * lock sequence, then use vsync interrupt to update the
+		 * frame rate, video format and static hdr structures and
+		 * notify the userspace.
+		 */
+
+		/*
+		 * Do this while driver has state as video locked though
+		 * it is implicit from the interrupt type i.e. vsync interrupt
+		 * can occur only when video is locked.
+		 * Avoid generating source change event twice.
+		 */
+		if (status & XSDIRX_INTR_VIDLOCK_MASK)
+			return IRQ_HANDLED;
+
+		valid = xsdirxss_read(core, XSDIRX_ST352_VALID_REG);
+		if (!(valid & XSDIRX_ST352_VALID_DS1_MASK))
+			return IRQ_HANDLED;
+
+		payload = xsdirxss_read(core, XSDIRX_ST352_DS1_REG);
+		/* Return if previous and current payload are same */
+		if (payload == state->prev_payload)
+			return IRQ_HANDLED;
+
+		if (xsdirx_get_stream_properties(state))
+			return IRQ_HANDLED;
+
+		memset(&state->event, 0, sizeof(state->event));
+		state->event.type = V4L2_EVENT_SOURCE_CHANGE;
+		state->event.u.src_change.changes =
+			V4L2_EVENT_SRC_CH_RESOLUTION;
+		v4l2_subdev_notify_event(&state->subdev, &state->event);
+	}
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xsdirxss_subscribe_event - Subscribe to video lock and unlock event
+ * @sd: V4L2 Sub device
+ * @fh: V4L2 File Handle
+ * @sub: Subcribe event structure
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int xsdirxss_subscribe_event(struct v4l2_subdev *sd,
+				    struct v4l2_fh *fh,
+				    struct v4l2_event_subscription *sub)
+{
+	int ret;
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	struct xsdirxss_core *core = &xsdirxss->core;
+
+	switch (sub->type) {
+	case V4L2_EVENT_XLNXSDIRX_UNDERFLOW:
+	case V4L2_EVENT_XLNXSDIRX_OVERFLOW:
+		ret = v4l2_event_subscribe(fh, sub, XSDIRX_MAX_EVENTS, NULL);
+		break;
+	case V4L2_EVENT_SOURCE_CHANGE:
+		ret = v4l2_src_change_event_subscribe(fh, sub);
+		break;
+	default:
+		return -EINVAL;
+	}
+	dev_dbg(core->dev, "Event subscribed : 0x%08x\n", sub->type);
+	return ret;
+}
+
+/**
+ * xsdirxss_unsubscribe_event - Unsubscribe from all events registered
+ * @sd: V4L2 Sub device
+ * @fh: V4L2 file handle
+ * @sub: pointer to Event unsubscription structure
+ *
+ * Return: zero on success, else a negative error code.
+ */
+static int xsdirxss_unsubscribe_event(struct v4l2_subdev *sd,
+				      struct v4l2_fh *fh,
+				      struct v4l2_event_subscription *sub)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	struct xsdirxss_core *core = &xsdirxss->core;
+
+	dev_dbg(core->dev, "Event unsubscribe : 0x%08x\n", sub->type);
+	return v4l2_event_unsubscribe(fh, sub);
+}
+
+/**
+ * xsdirxss_s_ctrl - This is used to set the Xilinx SDI Rx V4L2 controls
+ * @ctrl: V4L2 control to be set
+ *
+ * This function is used to set the V4L2 controls for the Xilinx SDI Rx
+ * Subsystem.
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int xsdirxss_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	int ret = 0;
+	struct xsdirxss_state *xsdirxss =
+		container_of(ctrl->handler,
+			     struct xsdirxss_state, ctrl_handler);
+	struct xsdirxss_core *core = &xsdirxss->core;
+
+	dev_dbg(core->dev, "set ctrl id = 0x%08x val = 0x%08x\n",
+		ctrl->id, ctrl->val);
+
+	if (xsdirxss->streaming) {
+		dev_err(core->dev, "Cannot set controls while streaming\n");
+		return -EINVAL;
+	}
+
+	xsdirx_core_disable(core);
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_SDIRX_FRAMER:
+		xsdirx_framer(core, ctrl->val);
+		xsdirxss->framer_enable = ctrl->val;
+		break;
+	case V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW:
+		xsdirx_setvidlockwindow(core, ctrl->val);
+		xsdirxss->vidlockwin = ctrl->val;
+		break;
+	case V4L2_CID_XILINX_SDIRX_EDH_ERRCNT_ENABLE:
+		xsdirx_setedherrcnttrigger(core, ctrl->val);
+		xsdirxss->edhmask = ctrl->val;
+		break;
+	case V4L2_CID_XILINX_SDIRX_SEARCH_MODES:
+		if (ctrl->val) {
+			if (core->mode == XSDIRXSS_SDI_STD_3G) {
+				dev_dbg(core->dev, "Upto 3G supported\n");
+				ctrl->val &= ~(BIT(XSDIRX_MODE_6G_OFFSET) |
+					       BIT(XSDIRX_MODE_12GI_OFFSET) |
+					       BIT(XSDIRX_MODE_12GF_OFFSET));
+			}
+
+			if (core->mode == XSDIRXSS_SDI_STD_6G) {
+				dev_dbg(core->dev, "Upto 6G supported\n");
+				ctrl->val &= ~(BIT(XSDIRX_MODE_12GI_OFFSET) |
+					       BIT(XSDIRX_MODE_12GF_OFFSET));
+			}
+
+			ret = xsdirx_set_modedetect(core, ctrl->val);
+			if (!ret)
+				xsdirxss->searchmask = ctrl->val;
+		} else {
+			dev_err(core->dev, "Select at least one mode!\n");
+			return -EINVAL;
+		}
+		break;
+	default:
+		xsdirxss_set(core, XSDIRX_RST_CTRL_REG,
+			     XSDIRX_RST_CTRL_SS_EN_MASK);
+		return -EINVAL;
+	}
+	xsdirx_core_enable(core);
+	return ret;
+}
+
+/**
+ * xsdirxss_g_volatile_ctrl - get the Xilinx SDI Rx controls
+ * @ctrl: Pointer to V4L2 control
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int xsdirxss_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
+{
+	u32 val;
+	struct xsdirxss_state *xsdirxss =
+		container_of(ctrl->handler,
+			     struct xsdirxss_state, ctrl_handler);
+	struct xsdirxss_core *core = &xsdirxss->core;
+	struct v4l2_metadata_hdr *hdr_ptr;
+
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_SDIRX_MODE_DETECT:
+		if (!xsdirxss->vidlocked) {
+			dev_err(core->dev, "Can't get values when video not locked!\n");
+			return -EINVAL;
+		}
+		val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+		val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
+
+		switch (val) {
+		case XSDIRX_MODE_SD_MASK:
+			ctrl->val = XSDIRX_MODE_SD_OFFSET;
+			break;
+		case XSDIRX_MODE_HD_MASK:
+			ctrl->val = XSDIRX_MODE_HD_OFFSET;
+			break;
+		case XSDIRX_MODE_3G_MASK:
+			ctrl->val = XSDIRX_MODE_3G_OFFSET;
+			break;
+		case XSDIRX_MODE_6G_MASK:
+			ctrl->val = XSDIRX_MODE_6G_OFFSET;
+			break;
+		case XSDIRX_MODE_12GI_MASK:
+			ctrl->val = XSDIRX_MODE_12GI_OFFSET;
+			break;
+		case XSDIRX_MODE_12GF_MASK:
+			ctrl->val = XSDIRX_MODE_12GF_OFFSET;
+			break;
+		}
+		break;
+	case V4L2_CID_XILINX_SDIRX_CRC:
+		ctrl->val = xsdirxss_read(core, XSDIRX_CRC_ERRCNT_REG);
+		xsdirxss_write(core, XSDIRX_CRC_ERRCNT_REG, 0xFFFF);
+		break;
+	case V4L2_CID_XILINX_SDIRX_EDH_ERRCNT:
+		val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+		val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
+		if (val == XSDIRX_MODE_SD_MASK) {
+			ctrl->val = xsdirxss_read(core, XSDIRX_EDH_ERRCNT_REG);
+		} else {
+			dev_dbg(core->dev, "%d - not in SD mode\n", ctrl->id);
+			return -EINVAL;
+		}
+		break;
+	case V4L2_CID_XILINX_SDIRX_EDH_STATUS:
+		val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+		val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
+		if (val == XSDIRX_MODE_SD_MASK) {
+			ctrl->val = xsdirxss_read(core, XSDIRX_EDH_STAT_REG);
+		} else {
+			dev_dbg(core->dev, "%d - not in SD mode\n", ctrl->id);
+			return -EINVAL;
+		}
+		break;
+	case V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED:
+		if (!xsdirxss->vidlocked) {
+			dev_err(core->dev, "Can't get values when video not locked!\n");
+			return -EINVAL;
+		}
+		ctrl->val = xsdirxss->ts_is_interlaced;
+		break;
+	case V4L2_CID_XILINX_SDIRX_ACTIVE_STREAMS:
+		if (!xsdirxss->vidlocked) {
+			dev_err(core->dev, "Can't get values when video not locked!\n");
+			return -EINVAL;
+		}
+		val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+		val &= XSDIRX_MODE_DET_STAT_ACT_STREAM_MASK;
+		val >>= XSDIRX_MODE_DET_STAT_ACT_STREAM_OFFSET;
+		ctrl->val = 1 << val;
+		break;
+	case V4L2_CID_XILINX_SDIRX_IS_3GB:
+		if (!xsdirxss->vidlocked) {
+			dev_err(core->dev, "Can't get values when video not locked!\n");
+			return -EINVAL;
+		}
+		val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
+		val &= XSDIRX_MODE_DET_STAT_LVLB_3G_MASK;
+		ctrl->val = val ? true : false;
+		break;
+	case V4L2_CID_METADATA_HDR:
+		if (!xsdirxss->vidlocked) {
+			dev_err(core->dev, "Can't get values when video not locked!\n");
+			return -EINVAL;
+		}
+		hdr_ptr = (struct v4l2_metadata_hdr *)ctrl->p_new.p;
+		hdr_ptr->metadata_type = V4L2_HDR_TYPE_HDR10;
+		hdr_ptr->size = sizeof(struct v4l2_hdr10_payload);
+		memcpy(hdr_ptr->payload, &xsdirxss->static_hdr,
+		       hdr_ptr->size);
+		break;
+	default:
+		dev_err(core->dev, "Get Invalid control id 0x%0x\n", ctrl->id);
+		return -EINVAL;
+	}
+	dev_dbg(core->dev, "Get ctrl id = 0x%08x val = 0x%08x\n",
+		ctrl->id, ctrl->val);
+	return 0;
+}
+
+/**
+ * xsdirxss_log_status - Logs the status of the SDI Rx Subsystem
+ * @sd: Pointer to V4L2 subdevice structure
+ *
+ * This function prints the current status of Xilinx SDI Rx Subsystem
+ *
+ * Return: 0 on success
+ */
+static int xsdirxss_log_status(struct v4l2_subdev *sd)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	struct xsdirxss_core *core = &xsdirxss->core;
+	u32 i;
+
+	v4l2_info(sd, "***** SDI Rx subsystem reg dump start *****\n");
+	for (i = 0; i < 0x28; i++) {
+		u32 data;
+
+		data = xsdirxss_read(core, i * 4);
+		v4l2_info(sd, "offset 0x%08x data 0x%08x\n",
+			  i * 4, data);
+	}
+	v4l2_info(sd, "***** SDI Rx subsystem reg dump end *****\n");
+	return 0;
+}
+
+/**
+ * xsdirxss_g_frame_interval - Get the frame interval
+ * @sd: V4L2 Sub device
+ * @fi: Pointer to V4l2 Sub device frame interval structure
+ *
+ * This function is used to get the frame interval.
+ * The frame rate can be integral or fractional.
+ * Integral frame rate e.g. numerator = 1000, denominator = 24000 => 24 fps
+ * Fractional frame rate e.g. numerator = 1001, denominator = 24000 => 23.97 fps
+ *
+ * Return: 0 on success
+ */
+static int xsdirxss_g_frame_interval(struct v4l2_subdev *sd,
+				     struct v4l2_subdev_frame_interval *fi)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	struct xsdirxss_core *core = &xsdirxss->core;
+
+	if (!xsdirxss->vidlocked) {
+		dev_err(core->dev, "Video not locked!\n");
+		return -EINVAL;
+	}
+
+	fi->interval = xsdirxss->frame_interval;
+
+	dev_dbg(core->dev, "frame rate numerator = %d denominator = %d\n",
+		xsdirxss->frame_interval.numerator,
+		xsdirxss->frame_interval.denominator);
+	return 0;
+}
+
+/**
+ * xsdirxss_s_stream - It is used to start/stop the streaming.
+ * @sd: V4L2 Sub device
+ * @enable: Flag (True / False)
+ *
+ * This function controls the start or stop of streaming for the
+ * Xilinx SDI Rx Subsystem.
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int xsdirxss_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	struct xsdirxss_core *core = &xsdirxss->core;
+
+	if (enable) {
+		if (!xsdirxss->vidlocked) {
+			dev_dbg(core->dev, "Video is not locked\n");
+			return -EINVAL;
+		}
+		if (xsdirxss->streaming) {
+			dev_dbg(core->dev, "Already streaming\n");
+			return -EINVAL;
+		}
+
+		xsdirx_streamflow_control(core, true);
+		xsdirxss->streaming = true;
+		dev_dbg(core->dev, "Streaming started\n");
+	} else {
+		if (!xsdirxss->streaming) {
+			dev_dbg(core->dev, "Stopped streaming already\n");
+			return 0;
+		}
+
+		xsdirx_streamflow_control(core, false);
+		xsdirxss->streaming = false;
+		dev_dbg(core->dev, "Streaming stopped\n");
+	}
+
+	return 0;
+}
+
+/**
+ * xsdirxss_g_input_status - It is used to determine if the video signal
+ * is present / locked onto or not.
+ *
+ * @sd: V4L2 Sub device
+ * @status: status of signal locked
+ *
+ * This is used to determine if the video signal is present and locked onto
+ * by the SDI Rx core or not based on vidlocked flag.
+ *
+ * Return: zero on success
+ */
+static int xsdirxss_g_input_status(struct v4l2_subdev *sd, u32 *status)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+
+	if (!xsdirxss->vidlocked)
+		*status = V4L2_IN_ST_NO_SYNC | V4L2_IN_ST_NO_SIGNAL;
+	else
+		*status = 0;
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+__xsdirxss_get_pad_format(struct xsdirxss_state *xsdirxss,
+			  struct v4l2_subdev_state *sd_state,
+			  unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xsdirxss->subdev,
+						    sd_state,
+						    pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xsdirxss->format;
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+/**
+ * xsdirxss_get_format - Get the pad format
+ * @sd: Pointer to V4L2 Sub device structure
+ * @cfg: Pointer to sub device pad information structure
+ * @fmt: Pointer to pad level media bus format
+ *
+ * This function is used to get the pad format information.
+ *
+ * Return: 0 on success
+ */
+static int xsdirxss_get_format(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_format *fmt)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	struct xsdirxss_core *core = &xsdirxss->core;
+	struct v4l2_mbus_framefmt *format;
+
+	if (!xsdirxss->vidlocked) {
+		dev_err(core->dev, "Video not locked!\n");
+		return -EINVAL;
+	}
+
+	format = __xsdirxss_get_pad_format(xsdirxss, sd_state,
+					   fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	dev_dbg(core->dev, "Stream width = %d height = %d Field = %d\n",
+		fmt->format.width, fmt->format.height, fmt->format.field);
+
+	return 0;
+}
+
+/**
+ * xsdirxss_set_format - This is used to set the pad format
+ * @sd: Pointer to V4L2 Sub device structure
+ * @cfg: Pointer to sub device pad information structure
+ * @fmt: Pointer to pad level media bus format
+ *
+ * This function is used to set the pad format.
+ * Since the pad format is fixed in hardware, it can't be
+ * modified on run time.
+ *
+ * Return: 0 on success
+ */
+static int xsdirxss_set_format(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_state *sd_state,
+			       struct v4l2_subdev_format *fmt)
+{
+	struct v4l2_mbus_framefmt *__format;
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+
+	dev_dbg(xsdirxss->core.dev,
+		"set width %d height %d code %d field %d colorspace %d\n",
+		fmt->format.width, fmt->format.height,
+		fmt->format.code, fmt->format.field,
+		fmt->format.colorspace);
+
+	__format = __xsdirxss_get_pad_format(xsdirxss, sd_state,
+					     fmt->pad, fmt->which);
+	if (!__format)
+		return -EINVAL;
+
+	/* Currently reset the code to one fixed in hardware */
+	/* TODO : Add checks for width height */
+	fmt->format.code = __format->code;
+
+	return 0;
+}
+
+/**
+ * xsdirxss_enum_mbus_code - Handle pixel format enumeration
+ * @sd: pointer to v4l2 subdev structure
+ * @cfg: V4L2 subdev pad configuration
+ * @code: pointer to v4l2_subdev_mbus_code_enum structure
+ *
+ * Return: -EINVAL or zero on success
+ */
+static int xsdirxss_enum_mbus_code(struct v4l2_subdev *sd,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+	u32 index = code->index;
+
+	if (code->pad || index >= 4)
+		return -EINVAL;
+
+	if (xsdirxss->core.bpc == 12)
+		code->code = xsdirxss_12bpc_mbus_fmts[index];
+	else
+		code->code = xsdirxss_10bpc_mbus_fmts[index];
+
+	return 0;
+}
+
+/**
+ * xsdirxss_enum_dv_timings: Enumerate all the supported DV timings
+ * @sd: pointer to v4l2 subdev structure
+ * @timings: DV timings structure to be returned.
+ *
+ * Return: -EINVAL incase of invalid index and pad or zero on success
+ */
+static int xsdirxss_enum_dv_timings(struct v4l2_subdev *sd,
+				    struct v4l2_enum_dv_timings *timings)
+{
+	if (timings->index >= ARRAY_SIZE(fmt_cap))
+		return -EINVAL;
+
+	if (timings->pad != 0)
+		return -EINVAL;
+
+	timings->timings = fmt_cap[timings->index];
+	return 0;
+}
+
+/**
+ * xsdirxss_query_dv_timings: Query for the current DV timings
+ * @sd: pointer to v4l2 subdev structure
+ * @timings: DV timings structure to be returned.
+ *
+ * Return: -ENOLCK when video is not locked, -ERANGE when corresponding timing
+ * entry is not found or zero on success.
+ */
+static int xsdirxss_query_dv_timings(struct v4l2_subdev *sd,
+				     struct v4l2_dv_timings *timings)
+{
+	struct xsdirxss_state *state = to_xsdirxssstate(sd);
+	unsigned int i;
+
+	if (!state->vidlocked)
+		return -ENOLCK;
+
+	for (i = 0; i < ARRAY_SIZE(xsdirxss_dv_timings); i++) {
+		if (state->format.width == xsdirxss_dv_timings[i].width &&
+		    state->format.height == xsdirxss_dv_timings[i].height &&
+		    state->frame_interval.denominator ==
+		    (xsdirxss_dv_timings[i].fps * 1000)) {
+			*timings = xsdirxss_dv_timings[i].format;
+			return 0;
+		}
+	}
+
+	return -ERANGE;
+}
+
+/**
+ * xsdirxss_open - Called on v4l2_open()
+ * @sd: Pointer to V4L2 sub device structure
+ * @fh: Pointer to V4L2 File handle
+ *
+ * This function is called on v4l2_open(). It sets the default format for pad.
+ *
+ * Return: 0 on success
+ */
+static int xsdirxss_open(struct v4l2_subdev *sd,
+			 struct v4l2_subdev_fh *fh)
+{
+	struct v4l2_mbus_framefmt *format;
+	struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
+
+	format = v4l2_subdev_get_try_format(sd, fh->state, 0);
+	*format = xsdirxss->default_format;
+
+	return 0;
+}
+
+/**
+ * xsdirxss_close - Called on v4l2_close()
+ * @sd: Pointer to V4L2 sub device structure
+ * @fh: Pointer to V4L2 File handle
+ *
+ * This function is called on v4l2_close().
+ *
+ * Return: 0 on success
+ */
+static int xsdirxss_close(struct v4l2_subdev *sd,
+			  struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xsdirxss_media_ops = {
+	.link_validate = v4l2_subdev_link_validate
+};
+
+static const struct v4l2_ctrl_ops xsdirxss_ctrl_ops = {
+	.g_volatile_ctrl = xsdirxss_g_volatile_ctrl,
+	.s_ctrl	= xsdirxss_s_ctrl
+};
+
+static const struct v4l2_ctrl_config xsdirxss_edh_ctrls[] = {
+	{
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_EDH_ERRCNT_ENABLE,
+		.name	= "SDI Rx : EDH Error Count Enable",
+		.type	= V4L2_CTRL_TYPE_BITMASK,
+		.min	= 0,
+		.max	= XSDIRX_EDH_ALLERR_MASK,
+		.def	= 0,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_EDH_ERRCNT,
+		.name	= "SDI Rx : EDH Error Count",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= 0xFFFF,
+		.step	= 1,
+		.def	= 0,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_EDH_STATUS,
+		.name	= "SDI Rx : EDH Status",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= 0xFFFFFFFF,
+		.step	= 1,
+		.def	= 0,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}
+};
+
+static const struct v4l2_ctrl_config xsdirxss_ctrls[] = {
+	{
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_FRAMER,
+		.name	= "SDI Rx : Enable Framer",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.step	= 1,
+		.def	= true,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW,
+		.name	= "SDI Rx : Video Lock Window",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= 0xFFFFFFFF,
+		.step	= 1,
+		.def	= XSDIRX_DEFAULT_VIDEO_LOCK_WINDOW,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_SEARCH_MODES,
+		.name	= "SDI Rx : Modes search Mask",
+		.type	= V4L2_CTRL_TYPE_BITMASK,
+		.min	= 0,
+		.max	= XSDIRX_DETECT_ALL_MODES,
+		.def	= XSDIRX_DETECT_ALL_MODES,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_MODE_DETECT,
+		.name	= "SDI Rx : Mode Detect Status",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= XSDIRX_MODE_SD_OFFSET,
+		.max	= XSDIRX_MODE_12GF_OFFSET,
+		.step	= 1,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_CRC,
+		.name	= "SDI Rx : CRC Error status",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 0,
+		.max	= 0xFFFFFFFF,
+		.step	= 1,
+		.def	= 0,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED,
+		.name	= "SDI Rx : TS is Interlaced",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.def	= false,
+		.step	= 1,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_ACTIVE_STREAMS,
+		.name	= "SDI Rx : Active Streams",
+		.type	= V4L2_CTRL_TYPE_INTEGER,
+		.min	= 1,
+		.max	= 16,
+		.def	= 1,
+		.step	= 1,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_XILINX_SDIRX_IS_3GB,
+		.name	= "SDI Rx : Is 3GB",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.def	= false,
+		.step	= 1,
+		.flags  = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_READ_ONLY,
+	}, {
+		.ops	= &xsdirxss_ctrl_ops,
+		.id	= V4L2_CID_METADATA_HDR,
+		.name	= "HDR Controls",
+		.type	= V4L2_CTRL_TYPE_HDR,
+		.min	= 0x8000000000000000,
+		.max	= 0x7FFFFFFFFFFFFFFF,
+		.step	= 1,
+		.def	= 0,
+		.elem_size = sizeof(struct v4l2_metadata_hdr),
+		.flags	= V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_HAS_PAYLOAD |
+			V4L2_CTRL_FLAG_READ_ONLY,
+	},
+};
+
+static const struct v4l2_subdev_core_ops xsdirxss_core_ops = {
+	.log_status = xsdirxss_log_status,
+	.subscribe_event = xsdirxss_subscribe_event,
+	.unsubscribe_event = xsdirxss_unsubscribe_event
+};
+
+static const struct v4l2_subdev_video_ops xsdirxss_video_ops = {
+	.g_frame_interval = xsdirxss_g_frame_interval,
+	.s_stream = xsdirxss_s_stream,
+	.g_input_status = xsdirxss_g_input_status,
+	.query_dv_timings = xsdirxss_query_dv_timings,
+};
+
+static const struct v4l2_subdev_pad_ops xsdirxss_pad_ops = {
+	.get_fmt = xsdirxss_get_format,
+	.set_fmt = xsdirxss_set_format,
+	.enum_mbus_code = xsdirxss_enum_mbus_code,
+	.enum_dv_timings = xsdirxss_enum_dv_timings,
+};
+
+static const struct v4l2_subdev_ops xsdirxss_ops = {
+	.core = &xsdirxss_core_ops,
+	.video = &xsdirxss_video_ops,
+	.pad = &xsdirxss_pad_ops
+};
+
+static const struct v4l2_subdev_internal_ops xsdirxss_internal_ops = {
+	.open = xsdirxss_open,
+	.close = xsdirxss_close
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int xsdirxss_parse_of(struct xsdirxss_state *xsdirxss)
+{
+	struct device_node *node = xsdirxss->core.dev->of_node;
+	struct device_node *ports = NULL;
+	struct device_node *port = NULL;
+	unsigned int nports = 0;
+	struct xsdirxss_core *core = &xsdirxss->core;
+	int ret;
+	const char *sdi_std;
+
+	core->include_edh = of_property_read_bool(node, "xlnx,include-edh");
+	dev_dbg(core->dev, "EDH property = %s\n",
+		core->include_edh ? "Present" : "Absent");
+
+	ret = of_property_read_string(node, "xlnx,line-rate", &sdi_std);
+	if (ret < 0) {
+		dev_err(core->dev, "xlnx,line-rate property not found\n");
+		return ret;
+	}
+
+	if (!strncmp(sdi_std, "12G_SDI_8DS", XSDIRX_MAX_STR_LENGTH)) {
+		core->mode = XSDIRXSS_SDI_STD_12G_8DS;
+	} else if (!strncmp(sdi_std, "6G_SDI", XSDIRX_MAX_STR_LENGTH)) {
+		core->mode = XSDIRXSS_SDI_STD_6G;
+	} else if (!strncmp(sdi_std, "3G_SDI", XSDIRX_MAX_STR_LENGTH)) {
+		core->mode = XSDIRXSS_SDI_STD_3G;
+	} else {
+		dev_err(core->dev, "Invalid Line Rate\n");
+		return -EINVAL;
+	}
+	dev_dbg(core->dev, "SDI Rx Line Rate = %s, mode = %d\n", sdi_std,
+		core->mode);
+
+	ret = of_property_read_u32(node, "xlnx,bpp", &core->bpc);
+	if (ret < 0) {
+		if (ret != -EINVAL) {
+			dev_err(core->dev, "failed to get xlnx,bpp\n");
+			return ret;
+		}
+
+		/*
+		 * For backward compatibility, set default bpc as 10
+		 * in case xlnx,bpp is not present.
+		 */
+		core->bpc = 10;
+	}
+
+	if (core->bpc != 10 && core->bpc != 12) {
+		dev_err(core->dev, "bits per component=%u. Can be 10 or 12 only\n",
+			core->bpc);
+		return -EINVAL;
+	}
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	for_each_child_of_node(ports, port) {
+		const struct xvip_video_format *format;
+		struct device_node *endpoint;
+
+		if (!port->name || of_node_cmp(port->name, "port"))
+			continue;
+
+		format = xvip_of_get_format(port);
+		if (IS_ERR(format)) {
+			dev_err(core->dev, "invalid format in DT");
+			return PTR_ERR(format);
+		}
+
+		dev_dbg(core->dev, "vf_code = %d bpc = %d bpp = %d\n",
+			format->vf_code, format->width, format->bpp);
+
+		if (format->vf_code != XVIP_VF_YUV_422 &&
+		    format->vf_code != XVIP_VF_YUV_420 &&
+		    format->vf_code != XVIP_VF_YUV_444 &&
+		    format->vf_code != XVIP_VF_RBG &&
+		    ((core->bpc == 10 && format->width != 10) ||
+		     (core->bpc == 12 && format->width != 12))) {
+			dev_err(core->dev,
+				"Incorrect UG934 video format set.\n");
+			return -EINVAL;
+		}
+		xsdirxss->vip_format = format;
+
+		endpoint = of_get_next_child(port, NULL);
+		if (!endpoint) {
+			dev_err(core->dev, "No port at\n");
+			return -EINVAL;
+		}
+
+		/* Count the number of ports. */
+		nports++;
+	}
+
+	if (nports != 1) {
+		dev_err(core->dev, "invalid number of ports %u\n", nports);
+		return -EINVAL;
+	}
+
+	/* Register interrupt handler */
+	core->irq = irq_of_parse_and_map(node, 0);
+	ret = devm_request_threaded_irq(core->dev, core->irq, NULL,
+					xsdirxss_irq_handler, IRQF_ONESHOT,
+					"xilinx-sdirxss", xsdirxss);
+	if (ret) {
+		dev_err(core->dev, "Err = %d Interrupt handler reg failed!\n",
+			ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xsdirxss_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xsdirxss_state *xsdirxss;
+	struct xsdirxss_core *core;
+	struct resource *res;
+	int ret;
+	unsigned int num_ctrls, num_edh_ctrls = 0, i;
+
+	xsdirxss = devm_kzalloc(&pdev->dev, sizeof(*xsdirxss), GFP_KERNEL);
+	if (!xsdirxss)
+		return -ENOMEM;
+
+	xsdirxss->core.dev = &pdev->dev;
+	core = &xsdirxss->core;
+
+	core->rst_gt_gpio = devm_gpiod_get_optional(&pdev->dev, "reset_gt",
+						    GPIOD_OUT_HIGH);
+	if (IS_ERR(core->rst_gt_gpio)) {
+		ret = PTR_ERR(core->rst_gt_gpio);
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Reset GT GPIO not setup in DT\n");
+		return ret;
+	}
+
+	core->rst_picxo_gpio = devm_gpiod_get_optional(&pdev->dev,
+						       "picxo_reset",
+						       GPIOD_OUT_LOW);
+	if (IS_ERR(core->rst_picxo_gpio)) {
+		ret = PTR_ERR(core->rst_picxo_gpio);
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "PICXO Reset GPIO not setup in DT\n");
+		return ret;
+	}
+
+	core->num_clks = ARRAY_SIZE(xsdirxss_clks);
+	core->clks = devm_kcalloc(&pdev->dev, core->num_clks,
+				  sizeof(*core->clks), GFP_KERNEL);
+	if (!core->clks)
+		return -ENOMEM;
+
+	for (i = 0; i < core->num_clks; i++)
+		core->clks[i].id = xsdirxss_clks[i];
+
+	ret = devm_clk_bulk_get(&pdev->dev, core->num_clks, core->clks);
+	if (ret)
+		return ret;
+
+	ret = clk_bulk_prepare_enable(core->num_clks, core->clks);
+	if (ret)
+		return ret;
+
+	ret = xsdirxss_parse_of(xsdirxss);
+	if (ret < 0)
+		goto clk_err;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xsdirxss->core.iomem = devm_ioremap_resource(xsdirxss->core.dev, res);
+	if (IS_ERR(xsdirxss->core.iomem)) {
+		ret = PTR_ERR(xsdirxss->core.iomem);
+		goto clk_err;
+	}
+
+	/* Reset the core */
+	xsdirx_streamflow_control(core, false);
+	xsdirx_core_disable(core);
+	xsdirx_clearintr(core, XSDIRX_INTR_ALL_MASK);
+	xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
+	xsdirx_enableintr(core, XSDIRX_INTR_ALL_MASK);
+	xsdirx_globalintr(core, true);
+	xsdirxss_write(core, XSDIRX_CRC_ERRCNT_REG, 0xFFFF);
+
+	/* Initialize V4L2 subdevice and media entity */
+	xsdirxss->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Initialize the default format */
+	xsdirxss->default_format.code = xsdirxss->vip_format->code;
+	xsdirxss->default_format.field = V4L2_FIELD_NONE;
+	xsdirxss->default_format.colorspace = V4L2_COLORSPACE_DEFAULT;
+	xsdirxss->default_format.width = XSDIRX_DEFAULT_WIDTH;
+	xsdirxss->default_format.height = XSDIRX_DEFAULT_HEIGHT;
+
+	xsdirxss->format = xsdirxss->default_format;
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xsdirxss->subdev;
+	v4l2_subdev_init(subdev, &xsdirxss_ops);
+
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xsdirxss_internal_ops;
+	strscpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_EVENTS | V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	subdev->entity.ops = &xsdirxss_media_ops;
+
+	v4l2_set_subdevdata(subdev, xsdirxss);
+
+	ret = media_entity_pads_init(&subdev->entity, 1, &xsdirxss->pad);
+	if (ret < 0)
+		goto error;
+
+	/* Initialise and register the controls */
+	num_ctrls = ARRAY_SIZE(xsdirxss_ctrls);
+
+	if (xsdirxss->core.include_edh)
+		num_edh_ctrls = ARRAY_SIZE(xsdirxss_edh_ctrls);
+
+	v4l2_ctrl_handler_init(&xsdirxss->ctrl_handler,
+			       (num_ctrls + num_edh_ctrls));
+
+	for (i = 0; i < num_ctrls; i++) {
+		struct v4l2_ctrl *ctrl;
+
+		dev_dbg(xsdirxss->core.dev, "%d %s ctrl = 0x%x\n",
+			i, xsdirxss_ctrls[i].name, xsdirxss_ctrls[i].id);
+
+		ctrl = v4l2_ctrl_new_custom(&xsdirxss->ctrl_handler,
+					    &xsdirxss_ctrls[i], NULL);
+		if (!ctrl) {
+			dev_dbg(xsdirxss->core.dev, "Failed to add %s ctrl\n",
+				xsdirxss_ctrls[i].name);
+			goto error;
+		}
+	}
+
+	if (xsdirxss->core.include_edh) {
+		for (i = 0; i < num_edh_ctrls; i++) {
+			struct v4l2_ctrl *ctrl;
+
+			dev_dbg(xsdirxss->core.dev, "%d %s ctrl = 0x%x\n",
+				i, xsdirxss_edh_ctrls[i].name,
+				xsdirxss_edh_ctrls[i].id);
+
+			ctrl = v4l2_ctrl_new_custom(&xsdirxss->ctrl_handler,
+						    &xsdirxss_edh_ctrls[i],
+						    NULL);
+			if (!ctrl) {
+				dev_dbg(xsdirxss->core.dev, "Failed to add %s ctrl\n",
+					xsdirxss_edh_ctrls[i].name);
+				goto error;
+			}
+		}
+	}
+
+	if (xsdirxss->ctrl_handler.error) {
+		dev_err(&pdev->dev, "failed to add controls\n");
+		ret = xsdirxss->ctrl_handler.error;
+		goto error;
+	}
+
+	subdev->ctrl_handler = &xsdirxss->ctrl_handler;
+
+	ret = v4l2_ctrl_handler_setup(&xsdirxss->ctrl_handler);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to set controls\n");
+		goto error;
+	}
+
+	platform_set_drvdata(pdev, xsdirxss);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	xsdirxss->streaming = false;
+
+	xsdirx_core_enable(core);
+
+	dev_info(xsdirxss->core.dev, "Xilinx SDI Rx Subsystem device found!\n");
+
+	return 0;
+error:
+	v4l2_ctrl_handler_free(&xsdirxss->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	xsdirx_globalintr(core, false);
+	xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
+clk_err:
+	clk_bulk_disable_unprepare(core->num_clks, core->clks);
+	return ret;
+}
+
+static int xsdirxss_remove(struct platform_device *pdev)
+{
+	struct xsdirxss_state *xsdirxss = platform_get_drvdata(pdev);
+	struct xsdirxss_core *core = &xsdirxss->core;
+	struct v4l2_subdev *subdev = &xsdirxss->subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&xsdirxss->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+
+	xsdirx_globalintr(core, false);
+	xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
+	xsdirx_core_disable(core);
+	xsdirx_streamflow_control(core, false);
+
+	clk_bulk_disable_unprepare(core->num_clks, core->clks);
+
+	return 0;
+}
+
+static const struct of_device_id xsdirxss_of_id_table[] = {
+	{ .compatible = "xlnx,v-smpte-uhdsdi-rx-ss" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xsdirxss_of_id_table);
+
+static struct platform_driver xsdirxss_driver = {
+	.driver = {
+		.name		= "xilinx-sdirxss",
+		.of_match_table	= xsdirxss_of_id_table,
+	},
+	.probe			= xsdirxss_probe,
+	.remove			= xsdirxss_remove,
+};
+
+module_platform_driver(xsdirxss_driver);
+
+MODULE_AUTHOR("Vishal Sagar <vsagar@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx SDI Rx Subsystem Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-switch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-switch.c
@@ -0,0 +1,476 @@
+/*
+ * Xilinx Video Switch
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/media-device.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XSW_CORE_CH_CTRL			0x0100
+#define XSW_CORE_CH_CTRL_FORCE			(1 << 3)
+
+#define XSW_SWITCH_STATUS			0x0104
+
+/**
+ * struct xswitch_device - Xilinx Video Switch device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: media pads
+ * @nsinks: number of sink pads (2 to 8)
+ * @nsources: number of source pads (1 to 8)
+ * @routing: sink pad connected to each source pad (-1 if none)
+ * @formats: active V4L2 media bus formats on sink pads
+ */
+struct xswitch_device {
+	struct xvip_device xvip;
+
+	struct media_pad *pads;
+	unsigned int nsinks;
+	unsigned int nsources;
+
+	int routing[8];
+
+	struct v4l2_mbus_framefmt *formats;
+};
+
+static inline struct xswitch_device *to_xsw(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xswitch_device, xvip.subdev);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xsw_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xswitch_device *xsw = to_xsw(subdev);
+	unsigned int unused_input;
+	unsigned int i;
+	u32 routing;
+
+	if (!enable) {
+		xvip_stop(&xsw->xvip);
+		return 0;
+	}
+
+	/*
+	 * All outputs must be routed to an input. When less than 8 inputs are
+	 * synthesized we can use input 7 for that purpose. Otherwise find an
+	 * unused input to connect to unused outputs.
+	 */
+	if (xsw->nsinks == 8) {
+		u32 mask;
+
+		for (i = 0, mask = 0xff; i < xsw->nsources; ++i) {
+			if (xsw->routing[i] != -1)
+				mask &= ~BIT(xsw->routing[i]);
+		}
+
+		/*
+		 * If all inputs are used all outputs are also used. We don't
+		 * need an unused input in that case, use a zero value.
+		 */
+		unused_input = mask ? ffs(mask) - 1 : 0;
+	} else {
+		unused_input = 7;
+	}
+
+	/* Configure routing. */
+	for (i = 0, routing = 0; i < xsw->nsources; ++i) {
+		unsigned int route;
+
+		route = xsw->routing[i] == -1 ?  unused_input : xsw->routing[i];
+		routing |= (XSW_CORE_CH_CTRL_FORCE | route)
+			<< (i * 4);
+	}
+
+	xvip_write(&xsw->xvip, XSW_CORE_CH_CTRL, routing);
+
+	xvip_write(&xsw->xvip, XVIP_CTRL_CONTROL,
+		   ((((unsigned long)1 << xsw->nsources) - 1) << 4) |
+		   XVIP_CTRL_CONTROL_SW_ENABLE);
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+static struct v4l2_mbus_framefmt *
+xsw_get_pad_format(struct xswitch_device *xsw,
+		   struct v4l2_subdev_state *sd_state,
+		   unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xsw->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xsw->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xsw_get_format(struct v4l2_subdev *subdev,
+			  struct v4l2_subdev_state *sd_state,
+			  struct v4l2_subdev_format *fmt)
+{
+	struct xswitch_device *xsw = to_xsw(subdev);
+	int pad = fmt->pad;
+	struct v4l2_mbus_framefmt *format;
+
+	if (pad >= xsw->nsinks) {
+		pad = xsw->routing[pad - xsw->nsinks];
+		if (pad < 0) {
+			memset(&fmt->format, 0, sizeof(fmt->format));
+			return 0;
+		}
+	}
+
+	format = xsw_get_pad_format(xsw, sd_state, pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xsw_set_format(struct v4l2_subdev *subdev,
+			  struct v4l2_subdev_state *sd_state,
+			  struct v4l2_subdev_format *fmt)
+{
+	struct xswitch_device *xsw = to_xsw(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* The source pad format is always identical to the sink pad format and
+	 * can't be modified.
+	 */
+	if (fmt->pad >= xsw->nsinks)
+		return xsw_get_format(subdev, sd_state, fmt);
+
+	format = xsw_get_pad_format(xsw, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	format->code = fmt->format.code;
+	format->width = clamp_t(unsigned int, fmt->format.width,
+				XVIP_MIN_WIDTH, XVIP_MAX_WIDTH);
+	format->height = clamp_t(unsigned int, fmt->format.height,
+				 XVIP_MIN_HEIGHT, XVIP_MAX_HEIGHT);
+	format->field = V4L2_FIELD_NONE;
+	format->colorspace = V4L2_COLORSPACE_SRGB;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xsw_get_routing(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_routing *route)
+{
+	struct xswitch_device *xsw = to_xsw(subdev);
+	unsigned int i;
+
+	mutex_lock(&subdev->entity.graph_obj.mdev->graph_mutex);
+
+	for (i = 0; i < min(xsw->nsources, route->num_routes); ++i) {
+		route->routes[i].sink = xsw->routing[i];
+		route->routes[i].source = i;
+	}
+
+	route->num_routes = xsw->nsources;
+
+	mutex_unlock(&subdev->entity.graph_obj.mdev->graph_mutex);
+
+	return 0;
+}
+
+static int xsw_set_routing(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_routing *route)
+{
+	struct xswitch_device *xsw = to_xsw(subdev);
+	unsigned int i;
+	int ret = 0;
+
+	mutex_lock(&subdev->entity.graph_obj.mdev->graph_mutex);
+
+	if (subdev->entity.stream_count) {
+		ret = -EBUSY;
+		goto done;
+	}
+
+	for (i = 0; i < xsw->nsources; ++i)
+		xsw->routing[i] = -1;
+
+	for (i = 0; i < route->num_routes; ++i)
+		xsw->routing[route->routes[i].source - xsw->nsinks] =
+			route->routes[i].sink;
+
+done:
+	mutex_unlock(&subdev->entity.graph_obj.mdev->graph_mutex);
+	return ret;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Operations
+ */
+
+/**
+ * xsw_init_formats - Initialize formats on all pads
+ * @subdev: tpgper V4L2 subdevice
+ * @fh: V4L2 subdev file handle
+ *
+ * Initialize all pad formats with default values. If fh is not NULL, try
+ * formats are initialized on the file handle. Otherwise active formats are
+ * initialized on the device.
+ *
+ * The function sets the format on pad 0 only. In two pads mode, this is the
+ * sink pad and the set format handler will propagate the format to the source
+ * pad. In one pad mode this is the source pad.
+ */
+static void xsw_init_formats(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_fh *fh)
+{
+	struct xswitch_device *xsw = to_xsw(subdev);
+	struct v4l2_subdev_format format;
+	unsigned int i;
+
+	for (i = 0; i < xsw->nsinks; ++i) {
+		memset(&format, 0, sizeof(format));
+
+		format.pad = 0;
+		format.which = fh ? V4L2_SUBDEV_FORMAT_TRY
+			     : V4L2_SUBDEV_FORMAT_ACTIVE;
+		format.format.width = 1920;
+		format.format.height = 1080;
+
+		xsw_set_format(subdev, fh ? fh->state : NULL, &format);
+	}
+}
+
+static int xsw_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	xsw_init_formats(subdev, fh);
+
+	return 0;
+}
+
+static int xsw_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_video_ops xsw_video_ops = {
+	.s_stream = xsw_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xsw_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xsw_get_format,
+	.set_fmt = xsw_set_format,
+	.get_routing = xsw_get_routing,
+	.set_routing = xsw_set_routing,
+};
+
+static struct v4l2_subdev_ops xsw_ops = {
+	.video = &xsw_video_ops,
+	.pad = &xsw_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xsw_internal_ops = {
+	.open = xsw_open,
+	.close = xsw_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static bool xsw_has_route(struct media_entity *entity, unsigned int pad0,
+			  unsigned int pad1)
+{
+	struct xswitch_device *xsw = container_of(entity, struct xswitch_device,
+						  xvip.subdev.entity);
+	unsigned int sink0, sink1;
+
+	/* Two sinks are never connected together. */
+	if (pad0 < xsw->nsinks && pad1 < xsw->nsinks)
+		return false;
+
+	sink0 = pad0 < xsw->nsinks ? pad0 : xsw->routing[pad0 - xsw->nsinks];
+	sink1 = pad1 < xsw->nsinks ? pad1 : xsw->routing[pad1 - xsw->nsinks];
+
+	return sink0 == sink1;
+}
+
+static const struct media_entity_operations xsw_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+	.has_route = xsw_has_route,
+};
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int xsw_parse_of(struct xswitch_device *xsw)
+{
+	struct device_node *node = xsw->xvip.dev->of_node;
+	int ret;
+
+	ret = of_property_read_u32(node, "#xlnx,inputs", &xsw->nsinks);
+	if (ret < 0) {
+		dev_err(xsw->xvip.dev, "missing or invalid #xlnx,%s property\n",
+			"inputs");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "#xlnx,outputs", &xsw->nsources);
+	if (ret < 0) {
+		dev_err(xsw->xvip.dev, "missing or invalid #xlnx,%s property\n",
+			"outputs");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xsw_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xswitch_device *xsw;
+	unsigned int npads;
+	unsigned int i;
+	int ret;
+
+	xsw = devm_kzalloc(&pdev->dev, sizeof(*xsw), GFP_KERNEL);
+	if (!xsw)
+		return -ENOMEM;
+
+	xsw->xvip.dev = &pdev->dev;
+
+	ret = xsw_parse_of(xsw);
+	if (ret < 0)
+		return ret;
+
+	ret = xvip_init_resources(&xsw->xvip);
+	if (ret < 0)
+		return ret;
+
+	/* Initialize V4L2 subdevice and media entity. Pad numbers depend on the
+	 * number of pads.
+	 */
+	npads = xsw->nsinks + xsw->nsources;
+	xsw->pads = devm_kzalloc(&pdev->dev, npads * sizeof(*xsw->pads),
+				 GFP_KERNEL);
+	if (!xsw->pads)
+		goto error_resources;
+
+	for (i = 0; i < xsw->nsinks; ++i)
+		xsw->pads[i].flags = MEDIA_PAD_FL_SINK;
+	for (; i < npads; ++i)
+		xsw->pads[i].flags = MEDIA_PAD_FL_SOURCE;
+
+	xsw->formats = devm_kzalloc(&pdev->dev,
+				    xsw->nsinks * sizeof(*xsw->formats),
+				    GFP_KERNEL);
+	if (!xsw->formats)
+		goto error_resources;
+
+	for (i = 0; i < xsw->nsources; ++i)
+		xsw->routing[i] = i < xsw->nsinks ? i : -1;
+
+	subdev = &xsw->xvip.subdev;
+	v4l2_subdev_init(subdev, &xsw_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xsw_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xsw);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	subdev->entity.ops = &xsw_media_ops;
+
+	xsw_init_formats(subdev, NULL);
+
+	ret = media_entity_pads_init(&subdev->entity, npads, xsw->pads);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xsw);
+
+	xvip_print_version(&xsw->xvip);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+error_resources:
+	xvip_cleanup_resources(&xsw->xvip);
+	return ret;
+}
+
+static int xsw_remove(struct platform_device *pdev)
+{
+	struct xswitch_device *xsw = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xsw->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+
+	xvip_cleanup_resources(&xsw->xvip);
+
+	return 0;
+}
+
+static const struct of_device_id xsw_of_id_table[] = {
+	{ .compatible = "xlnx,v-switch-1.0" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xsw_of_id_table);
+
+static struct platform_driver xsw_driver = {
+	.driver = {
+		.name		= "xilinx-switch",
+		.of_match_table	= xsw_of_id_table,
+	},
+	.probe			= xsw_probe,
+	.remove			= xsw_remove,
+};
+
+module_platform_driver(xsw_driver);
+
+MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>");
+MODULE_DESCRIPTION("Xilinx Video Switch Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-tpg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-tpg.c
@@ -20,6 +20,7 @@
 #include <media/v4l2-ctrls.h>
 #include <media/v4l2-subdev.h>
 
+#include "xilinx-hls-common.h"
 #include "xilinx-vip.h"
 #include "xilinx-vtc.h"
 
@@ -58,6 +59,36 @@
 #define XTPG_BAYER_PHASE_BGGR			3
 #define XTPG_BAYER_PHASE_OFF			4
 
+/* TPG v7 is a completely redesigned IP using Vivado HLS
+ * having a different AXI4-Lite interface
+ */
+#define XTPG_HLS_BG_PATTERN			0x0020
+#define XTPG_HLS_FG_PATTERN			0x0028
+#define XTPG_HLS_FG_PATTERN_CROSS_HAIR		(1 << 1)
+#define XTPG_HLS_MASK_ID			0x0030
+#define XTPG_HLS_MOTION_SPEED			0x0038
+#define XTPG_HLS_COLOR_FORMAT			0x0040
+#define XTPG_HLS_COLOR_FORMAT_RGB		0
+#define XTPG_HLS_COLOR_FORMAT_YUV_444		1
+#define XTPG_HLS_COLOR_FORMAT_YUV_422		2
+#define XTPG_HLS_COLOR_FORMAT_YUV_420		3
+#define XTPG_HLS_CROSS_HAIR_HOR			0x0048
+#define XTPG_HLS_CROSS_HAIR_VER			0x0050
+#define XTPG_HLS_ZPLATE_HOR_CNTL_START		0x0058
+#define XTPG_HLS_ZPLATE_HOR_CNTL_DELTA		0x0060
+#define XTPG_HLS_ZPLATE_VER_CNTL_START		0x0068
+#define XTPG_HLS_ZPLATE_VER_CNTL_DELTA		0x0070
+#define XTPG_HLS_BOX_SIZE			0x0078
+#define XTPG_HLS_BOX_COLOR_RED_CB		0x0080
+#define XTPG_HLS_BOX_COLOR_GREEN_CR		0x0088
+#define XTPG_HLS_BOX_COLOR_BLUE_Y		0x0090
+#define XTPG_HLS_ENABLE_INPUT			0x0098
+#define XTPG_HLS_USE_INPUT_VID_STREAM		(1 << 0)
+#define XTPG_HLS_PASS_THRU_START_X		0x00a0
+#define XTPG_HLS_PASS_THRU_START_Y		0x00a8
+#define XTPG_HLS_PASS_THRU_END_X		0x00b0
+#define XTPG_HLS_PASS_THRU_END_Y		0x00b8
+
 /*
  * The minimum blanking value is one clock cycle for the front porch, one clock
  * cycle for the sync pulse and one clock cycle for the back porch.
@@ -67,6 +98,15 @@
 #define XTPG_MIN_VBLANK			3
 #define XTPG_MAX_VBLANK			(XVTC_MAX_VSIZE - XVIP_MIN_HEIGHT)
 
+#define XTPG_MIN_WIDTH			(64)
+#define XTPG_MIN_HEIGHT			(64)
+#define XTPG_MAX_WIDTH			(10328)
+#define XTPG_MAX_HEIGHT			(7760)
+
+#define XTPG_MIN_PPC			1
+
+#define XTPG_MIN_FRM_INT		1
+
 /**
  * struct xtpg_device - Xilinx Test Pattern Generator device structure
  * @xvip: Xilinx Video IP device
@@ -82,8 +122,15 @@
  * @vblank: vertical blanking control
  * @pattern: test pattern control
  * @streaming: is the video stream active
+ * @is_hls: whether the IP core is HLS based
  * @vtc: video timing controller
  * @vtmux_gpio: video timing mux GPIO
+ * @rst_gpio: reset IP core GPIO
+ * @max_width: Maximum width supported by this instance
+ * @max_height: Maximum height supported by this instance
+ * @fi_d: frame interval denominator
+ * @fi_n: frame interval numerator
+ * @ppc: Pixels per clock control
  */
 struct xtpg_device {
 	struct xvip_device xvip;
@@ -102,9 +149,17 @@
 	struct v4l2_ctrl *vblank;
 	struct v4l2_ctrl *pattern;
 	bool streaming;
+	bool is_hls;
 
 	struct xvtc_device *vtc;
 	struct gpio_desc *vtmux_gpio;
+	struct gpio_desc *rst_gpio;
+
+	u32 max_width;
+	u32 max_height;
+	u32 fi_d;
+	u32 fi_n;
+	u32 ppc;
 };
 
 static inline struct xtpg_device *to_tpg(struct v4l2_subdev *subdev)
@@ -128,6 +183,32 @@
 	}
 }
 
+static void xtpg_config_vtc(struct xtpg_device *xtpg, int width, int height)
+{
+
+	struct xvtc_config config = {
+		.hblank_start = width / xtpg->ppc,
+		.hsync_start = width / xtpg->ppc + 1,
+		.vblank_start = height,
+		.vsync_start = height + 1,
+		.fps = xtpg->fi_d / xtpg->fi_n,
+	};
+	unsigned int htotal;
+	unsigned int vtotal;
+
+	htotal = min_t(unsigned int, XVTC_MAX_HSIZE,
+		       (v4l2_ctrl_g_ctrl(xtpg->hblank) + width) / xtpg->ppc);
+	vtotal = min_t(unsigned int, XVTC_MAX_VSIZE,
+		       v4l2_ctrl_g_ctrl(xtpg->vblank) + height);
+
+	config.hsync_end = htotal - 1;
+	config.hsize = htotal;
+	config.vsync_end = vtotal - 1;
+	config.vsize = vtotal;
+
+	xvtc_generator_start(xtpg->vtc, &config);
+}
+
 static void __xtpg_update_pattern_control(struct xtpg_device *xtpg,
 					  bool passthrough, bool pattern)
 {
@@ -164,6 +245,33 @@
  * V4L2 Subdevice Video Operations
  */
 
+static int xtpg_g_frame_interval(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct xtpg_device *xtpg = to_tpg(subdev);
+
+	fi->interval.numerator = xtpg->fi_n;
+	fi->interval.denominator = xtpg->fi_d;
+
+	return 0;
+}
+
+static int xtpg_s_frame_interval(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_frame_interval *fi)
+{
+	struct xtpg_device *xtpg = to_tpg(subdev);
+
+	if (!fi->interval.numerator || !fi->interval.denominator) {
+		xtpg->fi_n = XTPG_MIN_FRM_INT;
+		xtpg->fi_d = XTPG_MIN_FRM_INT;
+	} else {
+		xtpg->fi_n = fi->interval.numerator;
+		xtpg->fi_d = fi->interval.denominator;
+	}
+
+	return 0;
+}
+
 static int xtpg_s_stream(struct v4l2_subdev *subdev, int enable)
 {
 	struct xtpg_device *xtpg = to_tpg(subdev);
@@ -173,7 +281,27 @@
 	u32 bayer_phase;
 
 	if (!enable) {
-		xvip_stop(&xtpg->xvip);
+		if (!xtpg->is_hls) {
+			xvip_stop(&xtpg->xvip);
+		} else {
+			int ret;
+			/*
+			 * There is an known issue in TPG v7.0 that on
+			 * resolution change it doesn't generates pattern
+			 * correctly i.e some hor/ver offset is added.
+			 * As a workaround issue reset on stop.
+			 */
+			gpiod_set_value_cansleep(xtpg->rst_gpio, 0x1);
+			gpiod_set_value_cansleep(xtpg->rst_gpio, 0x0);
+			ret = v4l2_ctrl_handler_setup(&xtpg->ctrl_handler);
+			if (ret) {
+				struct device *dev = xtpg->xvip.dev;
+
+				dev_err(dev, "failed to set controls\n");
+				return ret;
+			}
+		}
+
 		if (xtpg->vtc)
 			xvtc_generator_stop(xtpg->vtc);
 
@@ -182,31 +310,36 @@
 		return 0;
 	}
 
-	xvip_set_frame_size(&xtpg->xvip, &xtpg->formats[0]);
+	if (xtpg->is_hls) {
+		u32 fmt = 0;
 
-	if (xtpg->vtc) {
-		struct xvtc_config config = {
-			.hblank_start = width,
-			.hsync_start = width + 1,
-			.vblank_start = height,
-			.vsync_start = height + 1,
-		};
-		unsigned int htotal;
-		unsigned int vtotal;
-
-		htotal = min_t(unsigned int, XVTC_MAX_HSIZE,
-			       v4l2_ctrl_g_ctrl(xtpg->hblank) + width);
-		vtotal = min_t(unsigned int, XVTC_MAX_VSIZE,
-			       v4l2_ctrl_g_ctrl(xtpg->vblank) + height);
-
-		config.hsync_end = htotal - 1;
-		config.hsize = htotal;
-		config.vsync_end = vtotal - 1;
-		config.vsize = vtotal;
-
-		xvtc_generator_start(xtpg->vtc, &config);
+		switch (xtpg->formats[0].code) {
+		case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		case MEDIA_BUS_FMT_VYYUYY10_4X20:
+			fmt = XTPG_HLS_COLOR_FORMAT_YUV_420;
+			break;
+		case MEDIA_BUS_FMT_UYVY8_1X16:
+		case MEDIA_BUS_FMT_UYVY10_1X20:
+			fmt = XTPG_HLS_COLOR_FORMAT_YUV_422;
+			break;
+		case MEDIA_BUS_FMT_VUY8_1X24:
+		case MEDIA_BUS_FMT_VUY10_1X30:
+			fmt = XTPG_HLS_COLOR_FORMAT_YUV_444;
+			break;
+		case MEDIA_BUS_FMT_RBG888_1X24:
+		case MEDIA_BUS_FMT_RBG101010_1X30:
+			fmt = XTPG_HLS_COLOR_FORMAT_RGB;
+			break;
+		}
+		xvip_write(&xtpg->xvip, XTPG_HLS_COLOR_FORMAT, fmt);
+		xvip_write(&xtpg->xvip, XHLS_REG_COLS, width);
+		xvip_write(&xtpg->xvip, XHLS_REG_ROWS, height);
+	} else {
+		xvip_set_frame_size(&xtpg->xvip, &xtpg->formats[0]);
 	}
 
+	if (xtpg->vtc)
+		xtpg_config_vtc(xtpg, width, height);
 	/*
 	 * Configure the bayer phase and video timing mux based on the
 	 * operation mode (passthrough or test pattern generation). The test
@@ -215,7 +348,11 @@
 	 */
 	mutex_lock(xtpg->ctrl_handler.lock);
 
-	xvip_clr_and_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
+	if (xtpg->is_hls)
+		xvip_write(&xtpg->xvip, XTPG_HLS_BG_PATTERN,
+			   xtpg->pattern->cur.val);
+	else
+		xvip_clr_and_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
 			 XTPG_PATTERN_MASK, xtpg->pattern->cur.val);
 
 	/*
@@ -229,18 +366,26 @@
 
 	mutex_unlock(xtpg->ctrl_handler.lock);
 
-	/*
-	 * For TPG v5.0, the bayer phase needs to be off for the pass through
-	 * mode, otherwise the external input would be subsampled.
-	 */
-	bayer_phase = passthrough ? XTPG_BAYER_PHASE_OFF
-		    : xtpg_get_bayer_phase(xtpg->formats[0].code);
-	xvip_write(&xtpg->xvip, XTPG_BAYER_PHASE, bayer_phase);
-
 	if (xtpg->vtmux_gpio)
 		gpiod_set_value_cansleep(xtpg->vtmux_gpio, !passthrough);
 
-	xvip_start(&xtpg->xvip);
+	if (xtpg->is_hls) {
+		xvip_set(&xtpg->xvip, XTPG_HLS_ENABLE_INPUT,
+			 XTPG_HLS_USE_INPUT_VID_STREAM);
+		xvip_set(&xtpg->xvip, XVIP_CTRL_CONTROL,
+			 XHLS_REG_CTRL_AUTO_RESTART |
+			 XVIP_CTRL_CONTROL_SW_ENABLE);
+	} else {
+		/*
+		 * For TPG v5.0, the bayer phase needs to be off for the pass
+		 * through mode, otherwise the external input would
+		 * be subsampled.
+		 */
+		bayer_phase = passthrough ? XTPG_BAYER_PHASE_OFF
+			    : xtpg_get_bayer_phase(xtpg->formats[0].code);
+		xvip_write(&xtpg->xvip, XTPG_BAYER_PHASE, bayer_phase);
+		xvip_start(&xtpg->xvip);
+	}
 
 	return 0;
 }
@@ -254,15 +399,23 @@
 		      struct v4l2_subdev_state *sd_state,
 		      unsigned int pad, u32 which)
 {
+	struct v4l2_mbus_framefmt *format;
+
 	switch (which) {
 	case V4L2_SUBDEV_FORMAT_TRY:
-		return v4l2_subdev_get_try_format(&xtpg->xvip.subdev,
-						  sd_state, pad);
+		format = v4l2_subdev_get_try_format(&xtpg->xvip.subdev,
+						    sd_state,
+						    pad);
+		break;
 	case V4L2_SUBDEV_FORMAT_ACTIVE:
-		return &xtpg->formats[pad];
+		format = &xtpg->formats[pad];
+		break;
 	default:
-		return NULL;
+		format = NULL;
+		break;
 	}
+
+	return format;
 }
 
 static int xtpg_get_format(struct v4l2_subdev *subdev,
@@ -270,9 +423,13 @@
 			   struct v4l2_subdev_format *fmt)
 {
 	struct xtpg_device *xtpg = to_tpg(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xtpg_get_pad_format(xtpg, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
 
-	fmt->format = *__xtpg_get_pad_format(xtpg, sd_state, fmt->pad,
-					     fmt->which);
+	fmt->format = *format;
 
 	return 0;
 }
@@ -286,6 +443,8 @@
 	u32 bayer_phase;
 
 	__format = __xtpg_get_pad_format(xtpg, sd_state, fmt->pad, fmt->which);
+	if (!__format)
+		return -EINVAL;
 
 	/* In two pads mode the source pad format is always identical to the
 	 * sink pad format.
@@ -302,7 +461,27 @@
 			__format->code = fmt->format.code;
 	}
 
-	xvip_set_format_size(__format, fmt);
+	if (xtpg->is_hls) {
+		switch (fmt->format.code) {
+		case MEDIA_BUS_FMT_VYYUYY8_1X24:
+		case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		case MEDIA_BUS_FMT_UYVY8_1X16:
+		case MEDIA_BUS_FMT_UYVY10_1X20:
+		case MEDIA_BUS_FMT_VUY8_1X24:
+		case MEDIA_BUS_FMT_VUY10_1X30:
+		case MEDIA_BUS_FMT_RBG888_1X24:
+		case MEDIA_BUS_FMT_RBG101010_1X30:
+			__format->code = fmt->format.code;
+			break;
+		default:
+			__format->code = xtpg->default_format.code;
+		}
+	}
+
+	__format->width = clamp_t(unsigned int, fmt->format.width,
+				  XTPG_MIN_WIDTH, xtpg->max_width);
+	__format->height = clamp_t(unsigned int, fmt->format.height,
+				   XTPG_MIN_HEIGHT, xtpg->max_height);
 
 	fmt->format = *__format;
 
@@ -310,6 +489,8 @@
 	if (xtpg->npads == 2) {
 		__format = __xtpg_get_pad_format(xtpg, sd_state, 1,
 						 fmt->which);
+		if (!__format)
+			return -EINVAL;
 		*__format = fmt->format;
 	}
 
@@ -325,6 +506,7 @@
 				struct v4l2_subdev_frame_size_enum *fse)
 {
 	struct v4l2_mbus_framefmt *format;
+	struct xtpg_device *xtpg = to_tpg(subdev);
 
 	format = v4l2_subdev_get_try_format(subdev, sd_state, fse->pad);
 
@@ -333,12 +515,13 @@
 
 	/* Min / max values for pad 0 is always fixed in both one and two pads
 	 * modes. In two pads mode, the source pad(= 1) size is identical to
-	 * the sink pad size */
+	 * the sink pad size.
+	 */
 	if (fse->pad == 0) {
-		fse->min_width = XVIP_MIN_WIDTH;
-		fse->max_width = XVIP_MAX_WIDTH;
-		fse->min_height = XVIP_MIN_HEIGHT;
-		fse->max_height = XVIP_MAX_HEIGHT;
+		fse->min_width = XTPG_MIN_WIDTH;
+		fse->max_width = xtpg->max_width;
+		fse->min_height = XTPG_MIN_HEIGHT;
+		fse->max_height = xtpg->max_height;
 	} else {
 		fse->min_width = format->width;
 		fse->max_width = format->width;
@@ -377,8 +560,12 @@
 						ctrl_handler);
 	switch (ctrl->id) {
 	case V4L2_CID_TEST_PATTERN:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
-				 XTPG_PATTERN_MASK, ctrl->val);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_BG_PATTERN,
+				   ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
+					 XTPG_PATTERN_MASK, ctrl->val);
 		return 0;
 	case V4L2_CID_XILINX_TPG_CROSS_HAIRS:
 		xvip_clr_or_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
@@ -389,10 +576,13 @@
 				XTPG_PATTERN_CONTROL_MOVING_BOX, ctrl->val);
 		return 0;
 	case V4L2_CID_XILINX_TPG_COLOR_MASK:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
-				 XTPG_PATTERN_CONTROL_COLOR_MASK_MASK,
-				 ctrl->val <<
-				 XTPG_PATTERN_CONTROL_COLOR_MASK_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_MASK_ID, ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
+				      XTPG_PATTERN_CONTROL_COLOR_MASK_MASK,
+				      ctrl->val <<
+				      XTPG_PATTERN_CONTROL_COLOR_MASK_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_STUCK_PIXEL:
 		xvip_clr_or_set(&xtpg->xvip, XTPG_PATTERN_CONTROL,
@@ -407,43 +597,85 @@
 				XTPG_PATTERN_CONTROL_MOTION, ctrl->val);
 		return 0;
 	case V4L2_CID_XILINX_TPG_MOTION_SPEED:
-		xvip_write(&xtpg->xvip, XTPG_MOTION_SPEED, ctrl->val);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_MOTION_SPEED,
+				   ctrl->val);
+		else
+			xvip_write(&xtpg->xvip, XTPG_MOTION_SPEED, ctrl->val);
 		return 0;
 	case V4L2_CID_XILINX_TPG_CROSS_HAIR_ROW:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_CROSS_HAIRS,
-				 XTPG_CROSS_HAIRS_ROW_MASK,
-				 ctrl->val << XTPG_CROSS_HAIRS_ROW_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_CROSS_HAIR_HOR,
+				    ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_CROSS_HAIRS,
+					 XTPG_CROSS_HAIRS_ROW_MASK,
+					 ctrl->val <<
+					 XTPG_CROSS_HAIRS_ROW_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_CROSS_HAIR_COLUMN:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_CROSS_HAIRS,
-				 XTPG_CROSS_HAIRS_COLUMN_MASK,
-				 ctrl->val << XTPG_CROSS_HAIRS_COLUMN_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_CROSS_HAIR_VER,
+				   ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_CROSS_HAIRS,
+					 XTPG_CROSS_HAIRS_COLUMN_MASK,
+					 ctrl->val <<
+					 XTPG_CROSS_HAIRS_COLUMN_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_ZPLATE_HOR_START:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_HOR_CONTROL,
-				 XTPG_ZPLATE_START_MASK,
-				 ctrl->val << XTPG_ZPLATE_START_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_ZPLATE_HOR_CNTL_START,
+				   ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_HOR_CONTROL,
+					 XTPG_ZPLATE_START_MASK,
+					 ctrl->val << XTPG_ZPLATE_START_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_ZPLATE_HOR_SPEED:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_HOR_CONTROL,
-				 XTPG_ZPLATE_SPEED_MASK,
-				 ctrl->val << XTPG_ZPLATE_SPEED_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_ZPLATE_HOR_CNTL_DELTA,
+				   ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_HOR_CONTROL,
+					 XTPG_ZPLATE_SPEED_MASK,
+					 ctrl->val << XTPG_ZPLATE_SPEED_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_ZPLATE_VER_START:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_VER_CONTROL,
-				 XTPG_ZPLATE_START_MASK,
-				 ctrl->val << XTPG_ZPLATE_START_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_ZPLATE_VER_CNTL_START,
+				   ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_VER_CONTROL,
+					 XTPG_ZPLATE_START_MASK,
+					 ctrl->val << XTPG_ZPLATE_START_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_ZPLATE_VER_SPEED:
-		xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_VER_CONTROL,
-				 XTPG_ZPLATE_SPEED_MASK,
-				 ctrl->val << XTPG_ZPLATE_SPEED_SHIFT);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_ZPLATE_VER_CNTL_DELTA,
+				   ctrl->val);
+		else
+			xvip_clr_and_set(&xtpg->xvip, XTPG_ZPLATE_VER_CONTROL,
+					 XTPG_ZPLATE_SPEED_MASK,
+					 ctrl->val << XTPG_ZPLATE_SPEED_SHIFT);
 		return 0;
 	case V4L2_CID_XILINX_TPG_BOX_SIZE:
-		xvip_write(&xtpg->xvip, XTPG_BOX_SIZE, ctrl->val);
+		if (xtpg->is_hls)
+			xvip_write(&xtpg->xvip, XTPG_HLS_BOX_SIZE, ctrl->val);
+		else
+			xvip_write(&xtpg->xvip, XTPG_BOX_SIZE, ctrl->val);
 		return 0;
 	case V4L2_CID_XILINX_TPG_BOX_COLOR:
-		xvip_write(&xtpg->xvip, XTPG_BOX_COLOR, ctrl->val);
+		if (xtpg->is_hls) {
+			xvip_write(&xtpg->xvip, XTPG_HLS_BOX_COLOR_RED_CB,
+				   ctrl->val >> 16);
+			xvip_write(&xtpg->xvip, XTPG_HLS_BOX_COLOR_GREEN_CR,
+				   ctrl->val >> 8);
+			xvip_write(&xtpg->xvip, XTPG_HLS_BOX_COLOR_BLUE_Y,
+				   ctrl->val);
+		} else {
+			xvip_write(&xtpg->xvip, XTPG_BOX_COLOR, ctrl->val);
+		}
 		return 0;
 	case V4L2_CID_XILINX_TPG_STUCK_PIXEL_THRESH:
 		xvip_write(&xtpg->xvip, XTPG_STUCK_PIXEL_THRESH, ctrl->val);
@@ -451,6 +683,9 @@
 	case V4L2_CID_XILINX_TPG_NOISE_GAIN:
 		xvip_write(&xtpg->xvip, XTPG_NOISE_GAIN, ctrl->val);
 		return 0;
+	case V4L2_CID_XILINX_TPG_HLS_FG_PATTERN:
+		xvip_write(&xtpg->xvip, XTPG_HLS_FG_PATTERN, ctrl->val);
+		return 0;
 	}
 
 	return 0;
@@ -464,6 +699,8 @@
 };
 
 static const struct v4l2_subdev_video_ops xtpg_video_ops = {
+	.g_frame_interval = xtpg_g_frame_interval,
+	.s_frame_interval = xtpg_s_frame_interval,
 	.s_stream = xtpg_s_stream,
 };
 
@@ -508,60 +745,51 @@
 	"Black/White Checker Board",
 };
 
-static struct v4l2_ctrl_config xtpg_ctrls[] = {
+static const char *const xtpg_hls_pattern_strings[] = {
+	"Passthrough",
+	"Horizontal Ramp",
+	"Vertical Ramp",
+	"Temporal Ramp",
+	"Solid Red",
+	"Solid Green",
+	"Solid Blue",
+	"Solid Black",
+	"Solid White",
+	"Color Bars",
+	"Zone Plate",
+	"Tartan Color Bars",
+	"Cross Hatch",
+	"Color Sweep",
+	"Vertical/Horizontal Ramps",
+	"Black/White Checker Board",
+	"PseudoRandom",
+};
+
+static const char *const xtpg_hls_fg_strings[] = {
+	"No Overlay",
+	"Moving Box",
+	"Cross Hairs",
+};
+
+static const struct v4l2_ctrl_config xtpg_hls_fg_ctrl = {
+	.ops	= &xtpg_ctrl_ops,
+	.id     = V4L2_CID_XILINX_TPG_HLS_FG_PATTERN,
+	.name   = "Test Pattern: Foreground Pattern",
+	.type   = V4L2_CTRL_TYPE_MENU,
+	.min	= 0,
+	.max	= ARRAY_SIZE(xtpg_hls_fg_strings) - 1,
+	.qmenu	= xtpg_hls_fg_strings,
+};
+
+static struct v4l2_ctrl_config xtpg_common_ctrls[] = {
 	{
-		.ops	= &xtpg_ctrl_ops,
-		.id	= V4L2_CID_XILINX_TPG_CROSS_HAIRS,
-		.name	= "Test Pattern: Cross Hairs",
-		.type	= V4L2_CTRL_TYPE_BOOLEAN,
-		.min	= false,
-		.max	= true,
-		.step	= 1,
-		.def	= 0,
-	}, {
-		.ops	= &xtpg_ctrl_ops,
-		.id	= V4L2_CID_XILINX_TPG_MOVING_BOX,
-		.name	= "Test Pattern: Moving Box",
-		.type	= V4L2_CTRL_TYPE_BOOLEAN,
-		.min	= false,
-		.max	= true,
-		.step	= 1,
-		.def	= 0,
-	}, {
-		.ops	= &xtpg_ctrl_ops,
-		.id	= V4L2_CID_XILINX_TPG_COLOR_MASK,
-		.name	= "Test Pattern: Color Mask",
-		.type	= V4L2_CTRL_TYPE_BITMASK,
-		.min	= 0,
-		.max	= 0xf,
-		.def	= 0,
-	}, {
-		.ops	= &xtpg_ctrl_ops,
-		.id	= V4L2_CID_XILINX_TPG_STUCK_PIXEL,
-		.name	= "Test Pattern: Stuck Pixel",
-		.type	= V4L2_CTRL_TYPE_BOOLEAN,
-		.min	= false,
-		.max	= true,
-		.step	= 1,
-		.def	= 0,
-	}, {
-		.ops	= &xtpg_ctrl_ops,
-		.id	= V4L2_CID_XILINX_TPG_NOISE,
-		.name	= "Test Pattern: Noise",
-		.type	= V4L2_CTRL_TYPE_BOOLEAN,
-		.min	= false,
-		.max	= true,
-		.step	= 1,
-		.def	= 0,
-	}, {
-		.ops	= &xtpg_ctrl_ops,
-		.id	= V4L2_CID_XILINX_TPG_MOTION,
-		.name	= "Test Pattern: Motion",
-		.type	= V4L2_CTRL_TYPE_BOOLEAN,
-		.min	= false,
-		.max	= true,
-		.step	= 1,
-		.def	= 0,
+		.ops    = &xtpg_ctrl_ops,
+		.id     = V4L2_CID_XILINX_TPG_COLOR_MASK,
+		.name   = "Test Pattern: Color Mask",
+		.type   = V4L2_CTRL_TYPE_BITMASK,
+		.min    = 0,
+		.max    = 0x7,
+		.def    = 0,
 	}, {
 		.ops	= &xtpg_ctrl_ops,
 		.id	= V4L2_CID_XILINX_TPG_MOTION_SPEED,
@@ -645,12 +873,61 @@
 	}, {
 		.ops	= &xtpg_ctrl_ops,
 		.id	= V4L2_CID_XILINX_TPG_BOX_COLOR,
-		.name	= "Test Pattern: Box Color(RGB)",
+		.name	= "Test Pattern: Box Color(RGB/YCbCr)",
 		.type	= V4L2_CTRL_TYPE_INTEGER,
 		.min	= 0,
 		.max	= (1 << 24) - 1,
 		.step	= 1,
 		.def	= 0,
+	},
+};
+
+static struct v4l2_ctrl_config xtpg_ctrls[] = {
+	{
+		.ops	= &xtpg_ctrl_ops,
+		.id	= V4L2_CID_XILINX_TPG_CROSS_HAIRS,
+		.name	= "Test Pattern: Cross Hairs",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.step	= 1,
+		.def	= 0,
+	}, {
+		.ops	= &xtpg_ctrl_ops,
+		.id	= V4L2_CID_XILINX_TPG_MOVING_BOX,
+		.name	= "Test Pattern: Moving Box",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.step	= 1,
+		.def	= 0,
+	}, {
+		.ops	= &xtpg_ctrl_ops,
+		.id	= V4L2_CID_XILINX_TPG_STUCK_PIXEL,
+		.name	= "Test Pattern: Stuck Pixel",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.step	= 1,
+		.def	= 0,
+	}, {
+		.ops	= &xtpg_ctrl_ops,
+		.id	= V4L2_CID_XILINX_TPG_NOISE,
+		.name	= "Test Pattern: Noise",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.step	= 1,
+		.def	= 0,
+	}, {
+		.ops	= &xtpg_ctrl_ops,
+		.id	= V4L2_CID_XILINX_TPG_MOTION,
+		.name	= "Test Pattern: Motion",
+		.type	= V4L2_CTRL_TYPE_BOOLEAN,
+		.min	= false,
+		.max	= true,
+		.step	= 1,
+		.def	= 0,
 	}, {
 		.ops	= &xtpg_ctrl_ops,
 		.id	= V4L2_CID_XILINX_TPG_STUCK_PIXEL_THRESH,
@@ -716,6 +993,49 @@
 	struct device_node *port;
 	unsigned int nports = 0;
 	bool has_endpoint = false;
+	int ret;
+
+	if (!of_device_is_compatible(dev->of_node, "xlnx,v-tpg-5.0"))
+		xtpg->is_hls = true;
+
+	ret = of_property_read_u32(node, "xlnx,max-height",
+				   &xtpg->max_height);
+	if (ret < 0) {
+		if (of_device_is_compatible(dev->of_node, "xlnx,v-tpg-8.0")) {
+			dev_err(dev, "xlnx,max-height dt property is missing!");
+			return -EINVAL;
+		}
+		xtpg->max_height = XTPG_MAX_HEIGHT;
+	} else if (xtpg->max_height > XTPG_MAX_HEIGHT ||
+		   xtpg->max_height < XTPG_MIN_HEIGHT) {
+		dev_err(dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-width",
+				   &xtpg->max_width);
+	if (ret < 0) {
+		if (of_device_is_compatible(dev->of_node, "xlnx,v-tpg-8.0")) {
+			dev_err(dev, "xlnx,max-width dt property is missing!");
+			return -EINVAL;
+		}
+		xtpg->max_width = XTPG_MAX_WIDTH;
+	} else if (xtpg->max_width > XTPG_MAX_WIDTH ||
+		   xtpg->max_width < XTPG_MIN_WIDTH) {
+		dev_err(dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,ppc",
+				   &xtpg->ppc);
+	if (ret < 0) {
+		xtpg->ppc = XTPG_MIN_PPC;
+		dev_dbg(dev, "failed to read ppc in dt\n");
+	} else if ((xtpg->ppc != 1) && (xtpg->ppc != 2) &&
+			(xtpg->ppc != 4) && (xtpg->ppc != 8)) {
+		dev_err(dev, "Invalid ppc config in dt\n");
+		return -EINVAL;
+	}
 
 	ports = of_get_child_by_name(node, "ports");
 	if (ports == NULL)
@@ -772,6 +1092,7 @@
 	struct v4l2_subdev *subdev;
 	struct xtpg_device *xtpg;
 	u32 i, bayer_phase;
+	u32 npatterns;
 	int ret;
 
 	xtpg = devm_kzalloc(&pdev->dev, sizeof(*xtpg), GFP_KERNEL);
@@ -795,14 +1116,29 @@
 		goto error_resource;
 	}
 
+	if (xtpg->is_hls) {
+		xtpg->rst_gpio = devm_gpiod_get(&pdev->dev, "reset",
+						   GPIOD_OUT_HIGH);
+		if (IS_ERR(xtpg->rst_gpio)) {
+			ret = PTR_ERR(xtpg->rst_gpio);
+			goto error_resource;
+		}
+	}
+
 	xtpg->vtc = xvtc_of_get(pdev->dev.of_node);
 	if (IS_ERR(xtpg->vtc)) {
 		ret = PTR_ERR(xtpg->vtc);
 		goto error_resource;
 	}
 
-	/* Reset and initialize the core */
-	xvip_reset(&xtpg->xvip);
+	/*
+	 * Reset and initialize the core. For TPG HLS version there
+	 * is no SW_RESET bit hence using GPIO based reset.
+	 */
+	if (xtpg->is_hls)
+		gpiod_set_value_cansleep(xtpg->rst_gpio, 0x0);
+	else
+		xvip_reset(&xtpg->xvip);
 
 	/* Initialize V4L2 subdevice and media entity. Pad numbers depend on the
 	 * number of pads.
@@ -818,11 +1154,23 @@
 	xtpg->default_format.code = xtpg->vip_format->code;
 	xtpg->default_format.field = V4L2_FIELD_NONE;
 	xtpg->default_format.colorspace = V4L2_COLORSPACE_SRGB;
-	xvip_get_frame_size(&xtpg->xvip, &xtpg->default_format);
 
-	bayer_phase = xtpg_get_bayer_phase(xtpg->vip_format->code);
-	if (bayer_phase != XTPG_BAYER_PHASE_OFF)
-		xtpg->bayer = true;
+	if (xtpg->is_hls) {
+		npatterns = ARRAY_SIZE(xtpg_hls_pattern_strings);
+		xtpg->default_format.width = xvip_read(&xtpg->xvip,
+						       XHLS_REG_COLS);
+		xtpg->default_format.height = xvip_read(&xtpg->xvip,
+							XHLS_REG_ROWS);
+	} else {
+		npatterns = ARRAY_SIZE(xtpg_pattern_strings);
+		xvip_get_frame_size(&xtpg->xvip, &xtpg->default_format);
+	}
+
+	if (!xtpg->is_hls) {
+		bayer_phase = xtpg_get_bayer_phase(xtpg->vip_format->code);
+		if (bayer_phase != XTPG_BAYER_PHASE_OFF)
+			xtpg->bayer = true;
+	}
 
 	xtpg->formats[0] = xtpg->default_format;
 	if (xtpg->npads == 2)
@@ -842,7 +1190,13 @@
 	if (ret < 0)
 		goto error;
 
-	v4l2_ctrl_handler_init(&xtpg->ctrl_handler, 3 + ARRAY_SIZE(xtpg_ctrls));
+	if (xtpg->is_hls)
+		v4l2_ctrl_handler_init(&xtpg->ctrl_handler, 4 +
+				       ARRAY_SIZE(xtpg_common_ctrls));
+	else
+		v4l2_ctrl_handler_init(&xtpg->ctrl_handler, 3 +
+				       ARRAY_SIZE(xtpg_common_ctrls) +
+				       ARRAY_SIZE(xtpg_ctrls));
 
 	xtpg->vblank = v4l2_ctrl_new_std(&xtpg->ctrl_handler, &xtpg_ctrl_ops,
 					 V4L2_CID_VBLANK, XTPG_MIN_VBLANK,
@@ -850,19 +1204,41 @@
 	xtpg->hblank = v4l2_ctrl_new_std(&xtpg->ctrl_handler, &xtpg_ctrl_ops,
 					 V4L2_CID_HBLANK, XTPG_MIN_HBLANK,
 					 XTPG_MAX_HBLANK, 1, 100);
-	xtpg->pattern = v4l2_ctrl_new_std_menu_items(&xtpg->ctrl_handler,
-					&xtpg_ctrl_ops, V4L2_CID_TEST_PATTERN,
-					ARRAY_SIZE(xtpg_pattern_strings) - 1,
-					1, 9, xtpg_pattern_strings);
 
-	for (i = 0; i < ARRAY_SIZE(xtpg_ctrls); i++)
-		v4l2_ctrl_new_custom(&xtpg->ctrl_handler, &xtpg_ctrls[i], NULL);
+	if (xtpg->is_hls) {
+		xtpg->pattern =
+			v4l2_ctrl_new_std_menu_items(&xtpg->ctrl_handler,
+						     &xtpg_ctrl_ops,
+						     V4L2_CID_TEST_PATTERN,
+						     npatterns - 1,
+						     1, 9,
+						     xtpg_hls_pattern_strings);
+		v4l2_ctrl_new_custom(&xtpg->ctrl_handler,
+				     &xtpg_hls_fg_ctrl, NULL);
+	} else {
+		xtpg->pattern =
+			v4l2_ctrl_new_std_menu_items(&xtpg->ctrl_handler,
+						     &xtpg_ctrl_ops,
+						     V4L2_CID_TEST_PATTERN,
+						     npatterns - 1,
+						     1, 9,
+						     xtpg_pattern_strings);
+
+		for (i = 0; i < ARRAY_SIZE(xtpg_ctrls); i++)
+			v4l2_ctrl_new_custom(&xtpg->ctrl_handler,
+					     &xtpg_ctrls[i], NULL);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(xtpg_common_ctrls); i++)
+		v4l2_ctrl_new_custom(&xtpg->ctrl_handler,
+				     &xtpg_common_ctrls[i], NULL);
 
 	if (xtpg->ctrl_handler.error) {
 		dev_err(&pdev->dev, "failed to add controls\n");
 		ret = xtpg->ctrl_handler.error;
 		goto error;
 	}
+
 	subdev->ctrl_handler = &xtpg->ctrl_handler;
 
 	xtpg_update_pattern_control(xtpg, true, true);
@@ -875,7 +1251,12 @@
 
 	platform_set_drvdata(pdev, xtpg);
 
-	xvip_print_version(&xtpg->xvip);
+	if (!xtpg->is_hls)
+		xvip_print_version(&xtpg->xvip);
+
+	/* Initialize default frame interval */
+	xtpg->fi_n = 1;
+	xtpg->fi_d = 30;
 
 	ret = v4l2_async_register_subdev(subdev);
 	if (ret < 0) {
@@ -912,6 +1293,8 @@
 
 static const struct of_device_id xtpg_of_id_table[] = {
 	{ .compatible = "xlnx,v-tpg-5.0" },
+	{ .compatible = "xlnx,v-tpg-7.0" },
+	{ .compatible = "xlnx,v-tpg-8.0" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, xtpg_of_id_table);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vip.c
@@ -24,22 +24,116 @@
  */
 
 static const struct xvip_video_format xvip_video_formats[] = {
+	{ XVIP_VF_YUV_420, 8, NULL, MEDIA_BUS_FMT_VYYUYY8_1X24,
+	  1, 12, V4L2_PIX_FMT_NV12, 2, 1, 1, 2 },
+	{ XVIP_VF_YUV_420, 8, NULL, MEDIA_BUS_FMT_VYYUYY8_1X24,
+	  1, 12, V4L2_PIX_FMT_NV12M, 2, 2, 1, 2 },
+	{ XVIP_VF_YUV_420, 10, NULL, MEDIA_BUS_FMT_VYYUYY10_4X20,
+	  1, 12, V4L2_PIX_FMT_XV15, 2, 1, 2, 2 },
+	{ XVIP_VF_YUV_420, 10, NULL, MEDIA_BUS_FMT_VYYUYY10_4X20,
+	  1, 12, V4L2_PIX_FMT_XV15M, 2, 2, 1, 2 },
+	{ XVIP_VF_YUV_420, 12, NULL, MEDIA_BUS_FMT_UYYVYY12_4X24,
+	  1, 12, V4L2_PIX_FMT_X012, 2, 1, 2, 2 },
+	{ XVIP_VF_YUV_420, 12, NULL, MEDIA_BUS_FMT_UYYVYY12_4X24,
+	  1, 12, V4L2_PIX_FMT_X012M, 2, 2, 1, 2 },
+	{ XVIP_VF_YUV_420, 16, NULL, MEDIA_BUS_FMT_UYYVYY16_4X32,
+	  2, 12, V4L2_PIX_FMT_X016, 2, 1, 2, 2 },
+	{ XVIP_VF_YUV_420, 16, NULL, MEDIA_BUS_FMT_UYYVYY16_4X32,
+	  2, 12, V4L2_PIX_FMT_X016M, 2, 2, 1, 2 },
 	{ XVIP_VF_YUV_422, 8, NULL, MEDIA_BUS_FMT_UYVY8_1X16,
-	  2, V4L2_PIX_FMT_YUYV },
+	  1, 16, V4L2_PIX_FMT_NV16, 2, 1, 1, 1 },
+	{ XVIP_VF_YUV_422, 8, NULL, MEDIA_BUS_FMT_UYVY8_1X16,
+	  1, 16, V4L2_PIX_FMT_NV16M, 2, 2, 1, 1 },
+	{ XVIP_VF_YUV_422, 8, NULL, MEDIA_BUS_FMT_UYVY8_1X16,
+	  2, 16, V4L2_PIX_FMT_YUYV, 1, 1, 2, 1 },
+	{ XVIP_VF_VUY_422, 8, NULL, MEDIA_BUS_FMT_UYVY8_1X16,
+	  2, 16, V4L2_PIX_FMT_UYVY, 1, 1, 2, 1 },
+	{ XVIP_VF_YUV_422, 10, NULL, MEDIA_BUS_FMT_UYVY10_1X20,
+	  1, 16, V4L2_PIX_FMT_XV20, 2, 1, 2, 1 },
+	{ XVIP_VF_YUV_422, 10, NULL, MEDIA_BUS_FMT_UYVY10_1X20,
+	  1, 16, V4L2_PIX_FMT_XV20M, 2, 2, 1, 1 },
+	{ XVIP_VF_YUV_422, 12, NULL, MEDIA_BUS_FMT_UYVY12_1X24,
+	  1, 16, V4L2_PIX_FMT_X212, 2, 1, 2, 1 },
+	{ XVIP_VF_YUV_422, 12, NULL, MEDIA_BUS_FMT_UYVY12_1X24,
+	  1, 16, V4L2_PIX_FMT_X212M, 2, 2, 1, 1 },
+	{ XVIP_VF_YUV_422, 16, NULL, MEDIA_BUS_FMT_UYVY16_2X32,
+	  2, 16, V4L2_PIX_FMT_X216, 2, 1, 2, 1 },
+	{ XVIP_VF_YUV_422, 16, NULL, MEDIA_BUS_FMT_UYVY16_2X32,
+	  2, 16, V4L2_PIX_FMT_X216M, 2, 2, 1, 1 },
+	{ XVIP_VF_YUV_444, 8, NULL, MEDIA_BUS_FMT_VUY8_1X24,
+	  3, 24, V4L2_PIX_FMT_VUY24, 1, 1, 1, 1 },
+	{ XVIP_VF_YUV_444, 10, NULL, MEDIA_BUS_FMT_VUY10_1X30,
+	  1, 24, V4L2_PIX_FMT_X403, 3, 1, 1, 1 },
 	{ XVIP_VF_YUV_444, 8, NULL, MEDIA_BUS_FMT_VUY8_1X24,
-	  3, V4L2_PIX_FMT_YUV444 },
+	  1, 24, V4L2_PIX_FMT_YUV444P, 3, 1, 1, 1 },
+	{ XVIP_VF_YUV_444, 8, NULL, MEDIA_BUS_FMT_VUY8_1X24,
+	  1, 8, V4L2_PIX_FMT_YUV444M, 3, 3, 1, 1 },
+	{ XVIP_VF_YUVX, 8, NULL, MEDIA_BUS_FMT_VUY8_1X24,
+	  4, 32, V4L2_PIX_FMT_XVUY32, 1, 1, 1, 1 },
+	{ XVIP_VF_YUVX, 10, NULL, MEDIA_BUS_FMT_VUY10_1X30,
+	  3, 32, V4L2_PIX_FMT_XVUY10, 1, 1, 1, 1 },
+	{ XVIP_VF_YUV_444, 12, NULL, MEDIA_BUS_FMT_VUY12_1X36,
+	  1, 24, V4L2_PIX_FMT_X412, 1, 1, 1, 1 },
+	{ XVIP_VF_YUV_444, 12, NULL, MEDIA_BUS_FMT_VUY12_1X36,
+	  1, 24, V4L2_PIX_FMT_X412M, 1, 1, 1, 1 },
+	{ XVIP_VF_YUV_444, 16, NULL, MEDIA_BUS_FMT_VUY16_1X48,
+	  2, 24, V4L2_PIX_FMT_X416, 1, 1, 1, 1 },
+	{ XVIP_VF_YUV_444, 16, NULL, MEDIA_BUS_FMT_VUY16_1X48,
+	  2, 24, V4L2_PIX_FMT_X416M, 1, 1, 1, 1 },
+	{ XVIP_VF_RBG, 8, NULL, MEDIA_BUS_FMT_RBG888_1X24,
+	  3, 24, V4L2_PIX_FMT_BGR24, 1, 1, 1, 1 },
 	{ XVIP_VF_RBG, 8, NULL, MEDIA_BUS_FMT_RBG888_1X24,
-	  3, 0 },
+	  3, 24, V4L2_PIX_FMT_RGB24, 1, 1, 1, 1 },
+	{ XVIP_VF_BGRX, 8, NULL, MEDIA_BUS_FMT_RBG888_1X24,
+	  4, 32, V4L2_PIX_FMT_BGRX32, 1, 1, 1, 1 },
+	{ XVIP_VF_XRGB, 8, NULL, MEDIA_BUS_FMT_RBG888_1X24,
+	  4, 32, V4L2_PIX_FMT_XBGR32, 1, 1, 1, 1 },
+	{ XVIP_VF_XBGR, 10, NULL, MEDIA_BUS_FMT_RBG101010_1X30,
+	  3, 32, V4L2_PIX_FMT_XBGR30, 1, 1, 1, 1 },
+	{ XVIP_VF_XBGR, 12, NULL, MEDIA_BUS_FMT_RBG121212_1X36,
+	  3, 40, V4L2_PIX_FMT_XBGR40, 1, 1, 1, 1 },
+	{ XVIP_VF_RBG, 16, NULL, MEDIA_BUS_FMT_RBG161616_1X48,
+	  6, 48, V4L2_PIX_FMT_BGR48, 1, 1, 1, 1 },
 	{ XVIP_VF_MONO_SENSOR, 8, "mono", MEDIA_BUS_FMT_Y8_1X8,
-	  1, V4L2_PIX_FMT_GREY },
+	  1, 8, V4L2_PIX_FMT_GREY, 1, 1, 1, 1 },
+	{ XVIP_VF_Y_GREY, 10, NULL, MEDIA_BUS_FMT_Y10_1X10,
+	  1, 32, V4L2_PIX_FMT_XY10, 1, 1, 1, 1 },
+	{ XVIP_VF_Y_GREY, 12, NULL, MEDIA_BUS_FMT_Y12_1X12,
+	  1, 12, V4L2_PIX_FMT_XY12, 1, 1, 1, 1 },
+	{ XVIP_VF_Y_GREY, 16, NULL, MEDIA_BUS_FMT_Y16_1X16,
+	  2, 16, V4L2_PIX_FMT_Y16, 1, 1, 1, 1 },
 	{ XVIP_VF_MONO_SENSOR, 8, "rggb", MEDIA_BUS_FMT_SRGGB8_1X8,
-	  1, V4L2_PIX_FMT_SRGGB8 },
+	  1, 8, V4L2_PIX_FMT_SGRBG8, 1, 1, 1, 1 },
 	{ XVIP_VF_MONO_SENSOR, 8, "grbg", MEDIA_BUS_FMT_SGRBG8_1X8,
-	  1, V4L2_PIX_FMT_SGRBG8 },
+	  1, 8, V4L2_PIX_FMT_SGRBG8, 1, 1, 1, 1 },
 	{ XVIP_VF_MONO_SENSOR, 8, "gbrg", MEDIA_BUS_FMT_SGBRG8_1X8,
-	  1, V4L2_PIX_FMT_SGBRG8 },
+	  1, 8, V4L2_PIX_FMT_SGBRG8, 1, 1, 1, 1 },
 	{ XVIP_VF_MONO_SENSOR, 8, "bggr", MEDIA_BUS_FMT_SBGGR8_1X8,
-	  1, V4L2_PIX_FMT_SBGGR8 },
+	  1, 8, V4L2_PIX_FMT_SBGGR8, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 10, "rggb", MEDIA_BUS_FMT_SRGGB10_1X10,
+	  2, 10, V4L2_PIX_FMT_SRGGB10, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 10, "grbg", MEDIA_BUS_FMT_SGRBG10_1X10,
+	  2, 10, V4L2_PIX_FMT_SGRBG10, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 10, "gbrg", MEDIA_BUS_FMT_SGBRG10_1X10,
+	  2, 10, V4L2_PIX_FMT_SGBRG10, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 10, "bggr", MEDIA_BUS_FMT_SBGGR10_1X10,
+	  2, 10, V4L2_PIX_FMT_SBGGR10, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 12, "rggb", MEDIA_BUS_FMT_SRGGB12_1X12,
+	  2, 12, V4L2_PIX_FMT_SRGGB12, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 12, "grbg", MEDIA_BUS_FMT_SGRBG12_1X12,
+	  2, 12, V4L2_PIX_FMT_SGRBG12, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 12, "gbrg", MEDIA_BUS_FMT_SGBRG12_1X12,
+	  2, 12, V4L2_PIX_FMT_SGBRG12, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 12, "bggr", MEDIA_BUS_FMT_SBGGR12_1X12,
+	  2, 12, V4L2_PIX_FMT_SBGGR12, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 16, "rggb", MEDIA_BUS_FMT_SRGGB16_1X16,
+	  2, 16, V4L2_PIX_FMT_SRGGB16, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 16, "grbg", MEDIA_BUS_FMT_SGRBG16_1X16,
+	  2, 16, V4L2_PIX_FMT_SGRBG16, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 16, "gbrg", MEDIA_BUS_FMT_SGBRG16_1X16,
+	  2, 16, V4L2_PIX_FMT_SGBRG16, 1, 1, 1, 1 },
+	{ XVIP_VF_MONO_SENSOR, 16, "bggr", MEDIA_BUS_FMT_SBGGR16_1X16,
+	  2, 16, V4L2_PIX_FMT_SBGGR16, 1, 1, 1, 1 },
 };
 
 /**
@@ -89,6 +183,89 @@
 EXPORT_SYMBOL_GPL(xvip_get_format_by_fourcc);
 
 /**
+ * xvip_bpl_scaling_factor - Retrieve bpl scaling factor for a 4CC
+ * @fourcc: the format 4CC
+ * @numerator: returning numerator of scaling factor
+ * @denominator: returning denominator of scaling factor
+ *
+ * Return: Return numerator and denominator values by address
+ */
+void xvip_bpl_scaling_factor(u32 fourcc, u32 *numerator, u32 *denominator)
+{
+	switch (fourcc) {
+	case V4L2_PIX_FMT_XY10:
+	case V4L2_PIX_FMT_XV15:
+	case V4L2_PIX_FMT_XV20:
+	case V4L2_PIX_FMT_X403:
+	case V4L2_PIX_FMT_XV15M:
+	case V4L2_PIX_FMT_XV20M:
+	case V4L2_PIX_FMT_XBGR30:
+	case V4L2_PIX_FMT_XVUY10:
+		*numerator = 10;
+		*denominator = 8;
+		break;
+	case V4L2_PIX_FMT_XBGR40:
+	case V4L2_PIX_FMT_XY12:
+	case V4L2_PIX_FMT_X012:
+	case V4L2_PIX_FMT_X012M:
+	case V4L2_PIX_FMT_X212:
+	case V4L2_PIX_FMT_X212M:
+	case V4L2_PIX_FMT_X412:
+	case V4L2_PIX_FMT_X412M:
+		*numerator = 12;
+		*denominator = 8;
+		break;
+	default:
+		*numerator = 1;
+		*denominator = 1;
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(xvip_bpl_scaling_factor);
+
+/**
+ * xvip_width_padding_factor - Retrieve width's padding factor for a 4CC
+ * @fourcc: the format 4CC
+ * @numerator: returning numerator of padding factor
+ * @denominator: returning denominator of padding factor
+ *
+ * Return: Return numerator and denominator values by address
+ */
+void xvip_width_padding_factor(u32 fourcc, u32 *numerator, u32 *denominator)
+{
+	switch (fourcc) {
+	case V4L2_PIX_FMT_XY10:
+	case V4L2_PIX_FMT_XV15:
+	case V4L2_PIX_FMT_XV20:
+	case V4L2_PIX_FMT_X403:
+	case V4L2_PIX_FMT_XV15M:
+	case V4L2_PIX_FMT_XV20M:
+	case V4L2_PIX_FMT_XBGR30:
+	case V4L2_PIX_FMT_XVUY10:
+		/* 32 bits are required per 30 bits of data */
+		*numerator = 32;
+		*denominator = 30;
+		break;
+	case V4L2_PIX_FMT_XBGR40:
+	case V4L2_PIX_FMT_XY12:
+	case V4L2_PIX_FMT_X012:
+	case V4L2_PIX_FMT_X012M:
+	case V4L2_PIX_FMT_X212:
+	case V4L2_PIX_FMT_X212M:
+	case V4L2_PIX_FMT_X412:
+	case V4L2_PIX_FMT_X412M:
+		*numerator = 40;
+		*denominator = 36;
+		break;
+	default:
+		*numerator = 1;
+		*denominator = 1;
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(xvip_width_padding_factor);
+
+/**
  * xvip_of_get_format - Parse a device tree node and return format information
  * @node: the device tree node
  *
@@ -102,9 +279,9 @@
 const struct xvip_video_format *xvip_of_get_format(struct device_node *node)
 {
 	const char *pattern = "mono";
-	unsigned int vf_code;
+	unsigned int vf_code = 0;
 	unsigned int i;
-	u32 width;
+	u32 width = 0;
 	int ret;
 
 	ret = of_property_read_u32(node, "xlnx,video-format", &vf_code);
@@ -115,8 +292,13 @@
 	if (ret < 0)
 		return ERR_PTR(ret);
 
-	if (vf_code == XVIP_VF_MONO_SENSOR)
-		of_property_read_string(node, "xlnx,cfa-pattern", &pattern);
+	if (vf_code == XVIP_VF_MONO_SENSOR) {
+		ret = of_property_read_string(node,
+					      "xlnx,cfa-pattern",
+					      &pattern);
+		if (ret < 0)
+			return ERR_PTR(ret);
+	}
 
 	for (i = 0; i < ARRAY_SIZE(xvip_video_formats); ++i) {
 		const struct xvip_video_format *format = &xvip_video_formats[i];
@@ -150,7 +332,7 @@
 	format->width = clamp_t(unsigned int, fmt->format.width,
 				XVIP_MIN_WIDTH, XVIP_MAX_WIDTH);
 	format->height = clamp_t(unsigned int, fmt->format.height,
-			 XVIP_MIN_HEIGHT, XVIP_MAX_HEIGHT);
+				 XVIP_MIN_HEIGHT, XVIP_MAX_HEIGHT);
 }
 EXPORT_SYMBOL_GPL(xvip_set_format_size);
 
@@ -216,8 +398,7 @@
 	if (IS_ERR(xvip->clk))
 		return PTR_ERR(xvip->clk);
 
-	clk_prepare_enable(xvip->clk);
-	return 0;
+	return clk_prepare_enable(xvip->clk);
 }
 EXPORT_SYMBOL_GPL(xvip_init_resources);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vip.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vip.h
@@ -107,21 +107,33 @@
  * @width: AXI4 format width in bits per component
  * @pattern: CFA pattern for Mono/Sensor formats
  * @code: media bus format code
- * @bpp: bytes per pixel (when stored in memory)
+ * @bpl_factor: Bytes per line factor
+ * @bpp: bits per pixel
  * @fourcc: V4L2 pixel format FCC identifier
+ * @num_planes: number of planes w.r.t. color format
+ * @buffers: number of buffers per format
+ * @hsub: Horizontal sampling factor of Chroma
+ * @vsub: Vertical sampling factor of Chroma
  */
 struct xvip_video_format {
 	unsigned int vf_code;
 	unsigned int width;
 	const char *pattern;
 	unsigned int code;
+	unsigned int bpl_factor;
 	unsigned int bpp;
 	u32 fourcc;
+	u8 num_planes;
+	u8 buffers;
+	u8 hsub;
+	u8 vsub;
 };
 
 const struct xvip_video_format *xvip_get_format_by_code(unsigned int code);
 const struct xvip_video_format *xvip_get_format_by_fourcc(u32 fourcc);
 const struct xvip_video_format *xvip_of_get_format(struct device_node *node);
+void xvip_bpl_scaling_factor(u32 fourcc, u32 *numerator, u32 *denominator);
+void xvip_width_padding_factor(u32 fourcc, u32 *numerator, u32 *denominator);
 void xvip_set_format_size(struct v4l2_mbus_framefmt *format,
 			  const struct v4l2_subdev_format *fmt);
 int xvip_enum_mbus_code(struct v4l2_subdev *subdev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vipp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vipp.c
@@ -15,6 +15,7 @@
 #include <linux/of_graph.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
+#include <linux/of_reserved_mem.h>
 
 #include <media/v4l2-async.h>
 #include <media/v4l2-common.h>
@@ -27,16 +28,27 @@
 #define XVIPP_DMA_S2MM				0
 #define XVIPP_DMA_MM2S				1
 
+/*
+ * This is for backward compatibility for existing applications,
+ * and planned to be deprecated
+ */
+static bool xvip_is_mplane = true;
+MODULE_PARM_DESC(is_mplane,
+		 "v4l2 device capability to handle multi planar formats");
+module_param_named(is_mplane, xvip_is_mplane, bool, 0444);
+
 /**
  * struct xvip_graph_entity - Entity in the video graph
  * @asd: subdev asynchronous registration information
  * @entity: media entity, from the corresponding V4L2 subdev
  * @subdev: V4L2 subdev
+ * @streaming: status of the V4L2 subdev if streaming or not
  */
 struct xvip_graph_entity {
 	struct v4l2_async_subdev asd; /* must be first */
 	struct media_entity *entity;
 	struct v4l2_subdev *subdev;
+	bool streaming;
 };
 
 static inline struct xvip_graph_entity *
@@ -65,6 +77,22 @@
 	return NULL;
 }
 
+static struct xvip_graph_entity *
+xvip_graph_find_entity_from_media(struct xvip_composite_device *xdev,
+				  struct media_entity *entity)
+{
+	struct xvip_graph_entity *xvip_entity;
+	struct v4l2_async_subdev *asd;
+
+	list_for_each_entry(asd, &xdev->notifier.asd_list, asd_list) {
+		xvip_entity = to_xvip_entity(asd);
+		if (xvip_entity->entity == entity)
+			return xvip_entity;
+	}
+
+	return NULL;
+}
+
 static int xvip_graph_build_one(struct xvip_composite_device *xdev,
 				struct xvip_graph_entity *entity)
 {
@@ -165,7 +193,6 @@
 		}
 	}
 
-	fwnode_handle_put(ep);
 	return ret;
 }
 
@@ -182,6 +209,190 @@
 	return NULL;
 }
 
+/**
+ * xvip_graph_entity_set_streaming - Update the streaming status
+ * @xdev: Composite video device
+ * @entity: graph entity to update
+ * @enable: enable/disable streaming status
+ *
+ * Update the streaming status of given entity.
+ *
+ * Return: previous streaming status (true or false)
+ */
+static bool xvip_graph_entity_set_streaming(struct xvip_composite_device *xdev,
+					    struct xvip_graph_entity *entity,
+					    bool enable)
+{
+	bool status = entity->streaming;
+
+	entity->streaming = enable;
+	return status;
+}
+
+static int
+xvip_graph_entity_start_stop_subdev(struct xvip_composite_device *xdev,
+				    struct xvip_graph_entity *entity, bool on)
+{
+	struct v4l2_subdev *subdev;
+	int ret = 0;
+
+	dev_dbg(xdev->dev, "%s entity %s\n",
+		on ? "Starting" : "Stopping", entity->entity->name);
+	subdev = media_entity_to_v4l2_subdev(entity->entity);
+
+	/*
+	 * start or stop the subdev only once in case if they are
+	 * shared between sub-graphs
+	 */
+	if (on) {
+		/* power-on subdevice */
+		ret = v4l2_subdev_call(subdev, core, s_power, 1);
+		if (ret < 0 && ret != -ENOIOCTLCMD) {
+			dev_err(xdev->dev,
+				"s_power on failed on subdev\n");
+			xvip_graph_entity_set_streaming(xdev, entity, 0);
+			return ret;
+		}
+
+		/* stream-on subdevice */
+		ret = v4l2_subdev_call(subdev, video, s_stream, 1);
+		if (ret < 0 && ret != -ENOIOCTLCMD) {
+			dev_err(xdev->dev,
+				"s_stream on failed on subdev\n");
+			v4l2_subdev_call(subdev, core, s_power, 0);
+			xvip_graph_entity_set_streaming(xdev, entity, 0);
+		}
+	} else {
+		/* stream-off subdevice */
+		ret = v4l2_subdev_call(subdev, video, s_stream, 0);
+		if (ret < 0 && ret != -ENOIOCTLCMD) {
+			dev_err(xdev->dev,
+				"s_stream off failed on subdev\n");
+			xvip_graph_entity_set_streaming(xdev, entity, 1);
+		}
+
+		/* power-off subdevice */
+		ret = v4l2_subdev_call(subdev, core, s_power, 0);
+		if (ret < 0 && ret != -ENOIOCTLCMD)
+			dev_err(xdev->dev,
+				"s_power off failed on subdev\n");
+	}
+
+	if (ret == -ENOIOCTLCMD)
+		ret = 0;
+
+	return ret;
+}
+
+/**
+ * xvip_graph_entity_start_stop - start / stop the graph entity
+ * @xdev: composite device
+ * @entity: entity to check
+ * @on: boolean flag. true for enable and false for disable
+ *
+ * Check if all immediate dependencies are ready dependeing on 'on' flag.
+ * If enabling, check all source pads. Sink pads for disabling. Once all
+ * dependencies are ready, set the streaming state on the entity. If the state
+ * is already set, optimize it by skipping checks.
+ *
+ * Return: true if the state is successfully or already set. false otherwise.
+ */
+static bool xvip_graph_entity_start_stop(struct xvip_composite_device *xdev,
+					 struct xvip_graph_entity *entity,
+					 bool on)
+{
+	unsigned long pad_flag = on ? MEDIA_PAD_FL_SOURCE : MEDIA_PAD_FL_SINK;
+	unsigned int i;
+	bool state;
+	int ret;
+
+	if (entity->streaming == on)
+		return true;
+
+	for (i = 0; i < entity->entity->num_pads; i++) {
+		struct xvip_graph_entity *remote;
+		struct media_pad *pad;
+
+		if (!(entity->entity->pads[i].flags & pad_flag))
+			continue;
+
+		/* skipping not connected pads */
+		pad = media_entity_remote_pad(&entity->entity->pads[i]);
+		if (!pad || !pad->entity)
+			continue;
+
+		/*
+		 * Skip if there is no remote. This entity is at the end,
+		 * such as DMA, sensor, or other type.
+		 */
+		remote = xvip_graph_find_entity_from_media(xdev, pad->entity);
+		if (!remote)
+			continue;
+
+		/* the dependency state doesn't meet */
+		if (remote->streaming != on) {
+			state = xvip_graph_entity_start_stop(xdev, remote, on);
+			if (!state)
+				return state;
+		}
+	}
+
+	/* set state and report if state is changed or not */
+	state = xvip_graph_entity_set_streaming(xdev, entity, on);
+	/* This shouldn't happen as check is already above */
+	if (state == on) {
+		WARN(1, "Should never get here\n");
+		return true;
+	}
+
+	ret = xvip_graph_entity_start_stop_subdev(xdev, entity, on);
+	if (ret < 0) {
+		dev_err(xdev->dev, "ret = %d for entity %s\n",
+			ret, entity->entity->name);
+		return false;
+	}
+
+	return true;
+}
+
+/**
+ * xvip_graph_pipeline_start_stop - start or stop the pipe in the graph
+ * @xdev: composite device
+ * @pipe: pipeline to start / stop
+ * @on: boolean flag. true for enable and false for disable
+ *
+ * Enable or disable the pipe in the graph by iterating the asd list.
+ * The pipe is a sub-graph, and the check ensures the given entity
+ * is part of the pipe before doing start or stop. This function
+ * or any subsequent functions don't and shouldn't change the asd list,
+ * so that there's no race if the caller holds the pipeline lock.
+ * xvip_graph_entity_start_stop() takes care of dependencies,
+ * or state-checking.
+ *
+ * Return: 0 for success, otherwise error code
+ */
+int xvip_graph_pipeline_start_stop(struct xvip_composite_device *xdev,
+				   struct xvip_pipeline *pipe, bool on)
+{
+	struct v4l2_async_subdev *asd;
+
+	list_for_each_entry(asd, &xdev->notifier.asd_list, asd_list) {
+		struct xvip_graph_entity *entity;
+		bool state;
+
+		entity = to_xvip_entity(asd);
+		/* skip an entity not belongng to the given pipe */
+		if (&pipe->pipe != entity->entity->pipe)
+			continue;
+
+		state = xvip_graph_entity_start_stop(xdev, entity, on);
+		if (!state)
+			return -EPIPE;
+	}
+
+	return 0;
+}
+
 static int xvip_graph_build_dma(struct xvip_composite_device *xdev)
 {
 	u32 link_flags = MEDIA_LNK_FL_ENABLED;
@@ -276,7 +487,6 @@
 		}
 	}
 
-	of_node_put(ep);
 	return ret;
 }
 
@@ -442,9 +652,11 @@
 		return ret;
 
 	if (strcmp(direction, "input") == 0)
-		type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+		type = xvip_is_mplane ? V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE :
+						V4L2_BUF_TYPE_VIDEO_CAPTURE;
 	else if (strcmp(direction, "output") == 0)
-		type = V4L2_BUF_TYPE_VIDEO_OUTPUT;
+		type = xvip_is_mplane ? V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE :
+					V4L2_BUF_TYPE_VIDEO_OUTPUT;
 	else
 		return -EINVAL;
 
@@ -462,8 +674,14 @@
 
 	list_add_tail(&dma->list, &xdev->dmas);
 
-	xdev->v4l2_caps |= type == V4L2_BUF_TYPE_VIDEO_CAPTURE
-			 ? V4L2_CAP_VIDEO_CAPTURE : V4L2_CAP_VIDEO_OUTPUT;
+	if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
+		xdev->v4l2_caps |= V4L2_CAP_VIDEO_CAPTURE_MPLANE;
+	else if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		xdev->v4l2_caps |= V4L2_CAP_VIDEO_CAPTURE;
+	else if (type == V4L2_BUF_TYPE_VIDEO_OUTPUT)
+		xdev->v4l2_caps |= V4L2_CAP_VIDEO_OUTPUT;
+	else if (type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
+		xdev->v4l2_caps |= V4L2_CAP_VIDEO_OUTPUT_MPLANE;
 
 	return 0;
 }
@@ -472,7 +690,7 @@
 {
 	struct device_node *ports;
 	struct device_node *port;
-	int ret;
+	int ret = 0;
 
 	ports = of_get_child_by_name(xdev->dev->of_node, "ports");
 	if (ports == NULL) {
@@ -482,13 +700,14 @@
 
 	for_each_child_of_node(ports, port) {
 		ret = xvip_graph_dma_init_one(xdev, port);
-		if (ret < 0) {
+		if (ret) {
 			of_node_put(port);
-			return ret;
+			break;
 		}
 	}
 
-	return 0;
+	of_node_put(ports);
+	return ret;
 }
 
 static void xvip_graph_cleanup(struct xvip_composite_device *xdev)
@@ -595,6 +814,7 @@
 		return -ENOMEM;
 
 	xdev->dev = &pdev->dev;
+	mutex_init(&xdev->lock);
 	INIT_LIST_HEAD(&xdev->dmas);
 	v4l2_async_notifier_init(&xdev->notifier);
 
@@ -606,6 +826,18 @@
 	if (ret < 0)
 		goto error;
 
+	xdev->atomic_streamon = of_property_read_bool(xdev->dev->of_node, "xlnx,atomic_streamon");
+
+	ret = of_reserved_mem_device_init(&pdev->dev);
+	if (ret)
+		dev_dbg(&pdev->dev, "of_reserved_mem_device_init: %d\n", ret);
+
+	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	if (ret) {
+		dev_err(&pdev->dev, "dma_set_mask_and_coherent: %d\n", ret);
+		goto error;
+	}
+
 	platform_set_drvdata(pdev, xdev);
 
 	dev_info(xdev->dev, "device registered\n");
@@ -621,6 +853,7 @@
 {
 	struct xvip_composite_device *xdev = platform_get_drvdata(pdev);
 
+	mutex_destroy(&xdev->lock);
 	xvip_graph_cleanup(xdev);
 	xvip_composite_v4l2_cleanup(xdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vipp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vipp.h
@@ -27,6 +27,9 @@
  * @notifier: V4L2 asynchronous subdevs notifier
  * @dmas: list of DMA channels at the pipeline output and input
  * @v4l2_caps: V4L2 capabilities of the whole device (see VIDIOC_QUERYCAP)
+ * @lock: This is to ensure all dma path entities acquire same pipeline object
+ * @atomic_streamon: Indicates that multi dma media pipe will get enabled
+ *  with single dma start
  */
 struct xvip_composite_device {
 	struct v4l2_device v4l2_dev;
@@ -37,6 +40,11 @@
 
 	struct list_head dmas;
 	u32 v4l2_caps;
+	struct mutex lock; /* lock to protect xvip pipeline instance */
+	bool atomic_streamon;
 };
 
+int xvip_graph_pipeline_start_stop(struct xvip_composite_device *xdev,
+				   struct xvip_pipeline *pipe, bool on);
+
 #endif /* __XILINX_VIPP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vpss-csc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vpss-csc.c
@@ -0,0 +1,1205 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx VPSS Color Space Converter
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/xilinx-v4l2-controls.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XV_CSC_AP_CTRL					(0x000)
+#define XV_CSC_INVIDEOFORMAT				(0x010)
+#define XV_CSC_OUTVIDEOFORMAT				(0x018)
+#define XV_CSC_WIDTH					(0x020)
+#define XV_CSC_HEIGHT					(0x028)
+#define XV_CSC_K11					(0x050)
+#define XV_CSC_K12					(0x058)
+#define XV_CSC_K13					(0x060)
+#define XV_CSC_K21					(0x068)
+#define XV_CSC_K22					(0x070)
+#define XV_CSC_K23					(0x078)
+#define XV_CSC_K31					(0x080)
+#define XV_CSC_K32					(0x088)
+#define XV_CSC_K33					(0x090)
+#define XV_CSC_ROFFSET					(0x098)
+#define XV_CSC_GOFFSET					(0x0a0)
+#define XV_CSC_BOFFSET					(0x0a8)
+#define XV_CSC_CLAMPMIN					(0x0b0)
+#define XV_CSC_CLIPMAX					(0x0b8)
+
+#define XV_CSC_FRACTIONAL_BITS	(12)
+#define XV_CSC_SCALE_FACTOR	(4096)
+/* This a VPSS CSC specific macro used to calculate Contrast */
+#define XV_CSC_DIVISOR		(10000)
+#define XV_CSC_DEFAULT_HEIGHT	(720)
+#define XV_CSC_DEFAULT_WIDTH	(1280)
+#define XV_CSC_K_MAX_ROWS	(3)
+#define XV_CSC_K_MAX_COLUMNS	(3)
+#define XV_CSC_MIN_WIDTH	(64)
+#define XV_CSC_MAX_WIDTH	(8192)
+#define XV_CSC_MIN_HEIGHT	(64)
+#define XV_CSC_MAX_HEIGHT	(4320)
+
+/* GPIO Reset Assert/De-assert */
+#define XCSC_RESET_ASSERT	(1)
+#define XCSC_RESET_DEASSERT	(0)
+/* Streaming Macros */
+#define XCSC_CLAMP_MIN_ZERO	(0)
+#define XCSC_AP_START		BIT(0)
+#define XCSC_AP_AUTO_RESTART	BIT(7)
+#define XCSC_STREAM_ON	(XCSC_AP_START | XCSC_AP_AUTO_RESTART)
+/* Color Control Macros */
+#define XCSC_COLOR_CTRL_COUNT		(5)
+#define XCSC_COLOR_CTRL_DEFAULT		(50)
+
+enum xcsc_color_fmt {
+	XVIDC_CSF_RGB = 0,
+	XVIDC_CSF_YCRCB_444,
+	XVIDC_CSF_YCRCB_422,
+	XVIDC_CSF_YCRCB_420,
+};
+
+enum xcsc_output_range {
+	XVIDC_CR_0_255 = 1,
+	XVIDC_CR_16_240,
+	XVIDC_CR_16_235
+};
+
+enum xcsc_color_depth {
+	XVIDC_BPC_8 = 8,
+	XVIDC_BPC_10 = 10,
+};
+
+static const s32
+rgb_unity_matrix[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1] = {
+	{XV_CSC_SCALE_FACTOR, 0, 0, 0},
+	{0, XV_CSC_SCALE_FACTOR, 0, 0},
+	{0, 0, XV_CSC_SCALE_FACTOR, 0},
+};
+
+static const s32
+ycrcb_to_rgb_unity[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1] = {
+	{
+	 11644 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0,
+	 17927 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0
+	},
+	{
+	 11644 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 -2132 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 -5329 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0
+	},
+	{
+	 11644 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 21124 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0,
+	 0
+	},
+};
+
+static const s32
+rgb_to_ycrcb_unity[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1] = {
+	{
+	 1826 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 6142 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 620 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0
+	},
+	{
+	 -1006 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 -3386 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 4392 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0
+	},
+	{
+	 4392 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 -3989 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 -403 * XV_CSC_SCALE_FACTOR / XV_CSC_DIVISOR,
+	 0,
+	},
+};
+
+/**
+ * struct xcsc_dev - xilinx vpss csc device structure
+ * @xvip: Xilinx Video IP core struct
+ * @pads: Media bus pads for VPSS CSC
+ * @formats: Current media bus formats
+ * @default_formats: Default media bus formats for VPSS CSC
+ * @vip_formats: Pointer to DT specified media bus code info
+ * @ctrl_handler: V4L2 Control Handler struct
+ * @custom_ctrls: Array of pointers to various custom controls
+ * @cft_in: IP or Hardware specific input video format
+ * @cft_out: IP or Hardware specific output video format
+ * @output_range: Color range for Outgoing video
+ * @color_depth: Data width used to represent color
+ * @brightness: Expected brightness value
+ * @contrast: Expected contrast value
+ * @red_gain: Expected red gain
+ * @green_gain: Expect green gain
+ * @blue_gain: Expected blue gain
+ * @brightness_active: Current brightness value
+ * @contrast_active: Current contrast value
+ * @red_gain_active: Current red gain
+ * @green_gain_active: Current green gain
+ * @blue_gain_active: Current blue gain
+ * @k_hw : Coefficients to be written to IP/Hardware
+ * @shadow_coeff: Coefficients to track RGB equivalents for color controls
+ * @clip_max: Maximum value to clip output color range
+ * @rst_gpio: Handle to PS GPIO specifier to assert/de-assert the reset line
+ * @max_width: Maximum width supported by IP.
+ * @max_height: Maximum height supported by IP.
+ */
+struct xcsc_dev {
+	struct xvip_device xvip;
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_formats[2];
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct v4l2_ctrl *custom_ctrls[XCSC_COLOR_CTRL_COUNT];
+
+	enum xcsc_color_fmt cft_in;
+	enum xcsc_color_fmt cft_out;
+	enum xcsc_output_range output_range;
+	enum xcsc_color_depth color_depth;
+	s32 brightness;
+	s32 contrast;
+	s32 red_gain;
+	s32 green_gain;
+	s32 blue_gain;
+	s32 brightness_active;
+	s32 contrast_active;
+	s32 red_gain_active;
+	s32 green_gain_active;
+	s32 blue_gain_active;
+	s32 k_hw[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1];
+	s32 shadow_coeff[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1];
+	s32 clip_max;
+	struct gpio_desc *rst_gpio;
+	u32 max_width;
+	u32 max_height;
+};
+
+#ifdef DEBUG
+static u32 xcsc_read(struct xcsc_dev *xcsc, u32 reg)
+{
+	u32 data;
+
+	data = xvip_read(&xcsc->xvip, reg);
+	return data;
+}
+
+static void xcsc_get_coeff(struct xcsc_dev *xcsc, s32 C[3][4])
+{
+	C[0][0] = xcsc_read(xcsc, XV_CSC_K11);
+	C[0][1] = xcsc_read(xcsc, XV_CSC_K12);
+	C[0][2] = xcsc_read(xcsc, XV_CSC_K13);
+	C[1][0] = xcsc_read(xcsc, XV_CSC_K21);
+	C[1][1] = xcsc_read(xcsc, XV_CSC_K22);
+	C[1][2] = xcsc_read(xcsc, XV_CSC_K23);
+	C[2][0] = xcsc_read(xcsc, XV_CSC_K31);
+	C[2][1] = xcsc_read(xcsc, XV_CSC_K32);
+	C[2][2] = xcsc_read(xcsc, XV_CSC_K33);
+	C[0][3] = xcsc_read(xcsc, XV_CSC_ROFFSET);
+	C[1][3] = xcsc_read(xcsc, XV_CSC_GOFFSET);
+	C[2][3] = xcsc_read(xcsc, XV_CSC_BOFFSET);
+}
+
+static void xcsc_print_coeff(struct xcsc_dev *xcsc)
+{
+	s32 C[3][4];
+
+	xcsc_get_coeff(xcsc, C);
+
+	dev_info(xcsc->xvip.dev,
+		 "-------------CSC Coeff Dump Start------\n");
+	dev_info(xcsc->xvip.dev,
+		 " R row : %5d  %5d  %5d\n",
+		 (s16)C[0][0], (s16)C[0][1], (s16)C[0][2]);
+	dev_info(xcsc->xvip.dev,
+		 " G row : %5d  %5d  %5d\n",
+		 (s16)C[1][0], (s16)C[1][1], (s16)C[1][2]);
+	dev_info(xcsc->xvip.dev,
+		 " B row : %5d  %5d  %5d\n",
+		 (s16)C[2][0], (s16)C[2][1], (s16)C[2][2]);
+	dev_info(xcsc->xvip.dev,
+		 "Offset : %5d  %5d  %5d\n",
+		 (s16)C[0][3], (s16)C[1][3], (s16)C[2][3]);
+	dev_info(xcsc->xvip.dev,
+		 "ClampMin: %3d  ClipMax %3d",
+		 xcsc_read(xcsc, XV_CSC_CLAMPMIN),
+		 xcsc_read(xcsc, XV_CSC_CLIPMAX));
+	dev_info(xcsc->xvip.dev,
+		 "-------------CSC Coeff Dump Stop-------\n");
+}
+
+static void
+xcsc_log_coeff(struct device *dev,
+	       s32 coeff[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1])
+{
+	if (!dev)
+		return;
+	dev_dbg(dev, "--- %s : Start Coeff Log ---", __func__);
+	dev_dbg(dev, "R row : %5d  %5d  %5d\n",
+		coeff[0][0], coeff[0][1], coeff[0][2]);
+	dev_dbg(dev, "G row : %5d  %5d  %5d\n",
+		coeff[1][0], coeff[1][1], coeff[1][2]);
+	dev_dbg(dev, "B row : %5d  %5d  %5d\n",
+		coeff[2][0], coeff[2][1], coeff[2][2]);
+	dev_dbg(dev, "Offset: %5d  %5d  %5d\n",
+		coeff[0][3], coeff[1][3], coeff[2][3]);
+	dev_dbg(dev, "---  %s : Stop Coeff Log ---", __func__);
+}
+
+static void xcsc_print_k_hw(struct xcsc_dev *xcsc)
+{
+	dev_dbg(xcsc->xvip.dev,
+		"-------------CSC Driver k_hw[][] Dump------------\n");
+	xcsc_log_coeff(xcsc->xvip.dev, xcsc->k_hw);
+	dev_dbg(xcsc->xvip.dev,
+		"-------------------------------------------------\n");
+}
+#endif /* DEBUG */
+
+static void xcsc_write(struct xcsc_dev *xcsc, u32 reg, u32 data)
+{
+	xvip_write(&xcsc->xvip, reg, data);
+}
+
+static void xcsc_write_rgb_3x3(struct xcsc_dev *xcsc)
+{
+	/* Write Matrix Coefficients */
+	xcsc_write(xcsc, XV_CSC_K11, xcsc->k_hw[0][0]);
+	xcsc_write(xcsc, XV_CSC_K12, xcsc->k_hw[0][1]);
+	xcsc_write(xcsc, XV_CSC_K13, xcsc->k_hw[0][2]);
+	xcsc_write(xcsc, XV_CSC_K21, xcsc->k_hw[1][0]);
+	xcsc_write(xcsc, XV_CSC_K22, xcsc->k_hw[1][1]);
+	xcsc_write(xcsc, XV_CSC_K23, xcsc->k_hw[1][2]);
+	xcsc_write(xcsc, XV_CSC_K31, xcsc->k_hw[2][0]);
+	xcsc_write(xcsc, XV_CSC_K32, xcsc->k_hw[2][1]);
+	xcsc_write(xcsc, XV_CSC_K33, xcsc->k_hw[2][2]);
+}
+
+static void xcsc_write_rgb_offset(struct xcsc_dev *xcsc)
+{
+	/* Write RGB Offsets */
+	xcsc_write(xcsc, XV_CSC_ROFFSET, xcsc->k_hw[0][3]);
+	xcsc_write(xcsc, XV_CSC_GOFFSET, xcsc->k_hw[1][3]);
+	xcsc_write(xcsc, XV_CSC_BOFFSET, xcsc->k_hw[2][3]);
+}
+
+static void xcsc_write_coeff(struct xcsc_dev *xcsc)
+{
+	xcsc_write_rgb_3x3(xcsc);
+	xcsc_write_rgb_offset(xcsc);
+}
+
+static void xcsc_set_control_defaults(struct xcsc_dev *xcsc)
+{
+	/* These are VPSS CSC IP specific defaults */
+	xcsc->brightness = 120;
+	xcsc->contrast = 0;
+	xcsc->red_gain = 120;
+	xcsc->blue_gain = 120;
+	xcsc->green_gain = 120;
+	xcsc->brightness_active	= 120;
+	xcsc->contrast_active = 0;
+	xcsc->red_gain_active = 120;
+	xcsc->blue_gain_active = 120;
+	xcsc->green_gain_active = 120;
+}
+
+static void xcsc_copy_coeff(
+	s32 dest[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1],
+	s32 const src[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1])
+{
+	unsigned int i, j;
+
+	for (i = 0; i < XV_CSC_K_MAX_ROWS; i++)
+		for (j = 0; j < XV_CSC_K_MAX_COLUMNS + 1; j++)
+			memcpy(&dest[i][j], &src[i][j], sizeof(dest[0][0]));
+}
+
+static void xcsc_set_unity_matrix(struct xcsc_dev *xcsc)
+{
+	xcsc_copy_coeff(xcsc->k_hw, rgb_unity_matrix);
+	xcsc_copy_coeff(xcsc->shadow_coeff, rgb_unity_matrix);
+}
+
+static void xcsc_set_default_state(struct xcsc_dev *xcsc)
+{
+	xcsc->cft_in = XVIDC_CSF_RGB;
+	xcsc->cft_out = XVIDC_CSF_RGB;
+	xcsc->output_range = XVIDC_CR_0_255;
+	/* Needed to add 10, 12 and 16 bit color depth support */
+	xcsc->clip_max = BIT(xcsc->color_depth) - 1;
+	xcsc_set_control_defaults(xcsc);
+	xcsc_set_unity_matrix(xcsc);
+	xcsc_write(xcsc, XV_CSC_INVIDEOFORMAT, xcsc->cft_in);
+	xcsc_write(xcsc, XV_CSC_OUTVIDEOFORMAT, xcsc->cft_out);
+	xcsc_write_coeff(xcsc);
+	xcsc_write(xcsc, XV_CSC_CLIPMAX, xcsc->clip_max);
+	xcsc_write(xcsc, XV_CSC_CLAMPMIN, XCSC_CLAMP_MIN_ZERO);
+}
+
+static void
+xcsc_ycrcb_to_rgb(struct xcsc_dev *xcsc, s32 *clip_max,
+		  s32 temp[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1])
+{
+	u16 bpc_scale = BIT(xcsc->color_depth - 8);
+
+	/*
+	 * See http://graficaobscura.com/matrix/index.html for
+	 * how these numbers are derived. The VPSS CSC IP is
+	 * derived from this Matrix style algorithm. And the
+	 * 'magic' numbers here are derived from the algorithm.
+	 *
+	 * XV_CSC_DIVISOR is used to help with floating constants
+	 * while performing multiplicative operations
+	 *
+	 * Coefficients valid only for BT 709
+	 */
+	dev_dbg(xcsc->xvip.dev, "Performing YCrCb to RGB BT 709");
+	xcsc_copy_coeff(temp, ycrcb_to_rgb_unity);
+	temp[0][3] = -248 * bpc_scale;
+	temp[1][3] = 77 * bpc_scale;
+	temp[2][3] = -289 * bpc_scale;
+	*clip_max = BIT(xcsc->color_depth) - 1;
+}
+
+static void
+xcsc_matrix_multiply(s32 K1[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1],
+		     s32 K2[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1],
+		     s32 kout[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1])
+{
+	s32 A, B, C, D, E, F, G, H, I, J, K, L, M, N;
+	s32 O, P, Q, R, S, T, U, V, W, X;
+
+	A = K1[0][0]; B = K1[0][1]; C = K1[0][2]; J = K1[0][3];
+	D = K1[1][0]; E = K1[1][1]; F = K1[1][2]; K = K1[1][3];
+	G = K1[2][0]; H = K1[2][1]; I = K1[2][2]; L = K1[2][3];
+
+	M = K2[0][0]; N = K2[0][1]; O = K2[0][2]; V = K2[0][3];
+	P = K2[1][0]; Q = K2[1][1]; R = K2[1][2]; W = K2[1][3];
+	S = K2[2][0]; T = K2[2][1]; U = K2[2][2]; X = K2[2][3];
+
+	kout[0][0] = (M * A + N * D + O * G) / XV_CSC_SCALE_FACTOR;
+	kout[0][1] = (M * B + N * E + O * H) / XV_CSC_SCALE_FACTOR;
+	kout[0][2] = (M * C + N * F + O * I) / XV_CSC_SCALE_FACTOR;
+	kout[1][0] = (P * A + Q * D + R * G) / XV_CSC_SCALE_FACTOR;
+	kout[1][1] = (P * B + Q * E + R * H) / XV_CSC_SCALE_FACTOR;
+	kout[1][2] = (P * C + Q * F + R * I) / XV_CSC_SCALE_FACTOR;
+	kout[2][0] = (S * A + T * D + U * G) / XV_CSC_SCALE_FACTOR;
+	kout[2][1] = (S * B + T * E + U * H) / XV_CSC_SCALE_FACTOR;
+	kout[2][2] = (S * C + T * F + U * I) / XV_CSC_SCALE_FACTOR;
+	kout[0][3] = ((M * J + N * K + O * L) / XV_CSC_SCALE_FACTOR) + V;
+	kout[1][3] = ((P * J + Q * K + R * L) / XV_CSC_SCALE_FACTOR) + W;
+	kout[2][3] = ((S * J + T * K + U * L) / XV_CSC_SCALE_FACTOR) + X;
+}
+
+static void
+xcsc_rgb_to_ycrcb(struct xcsc_dev *xcsc, s32 *clip_max,
+		  s32 temp[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1])
+{
+	u16 bpc_scale = BIT(xcsc->color_depth - 8);
+
+	/*
+	 * See http://graficaobscura.com/matrix/index.html for
+	 * how these numbers are derived. The VPSS CSC IP is
+	 * derived from this Matrix style algorithm. And the
+	 * 'magic' numbers here are derived from the algorithm.
+	 *
+	 * XV_CSC_DIVISOR is used to help with floating constants
+	 * while performing multiplicative operations
+	 *
+	 * Coefficients valid only for BT 709
+	 */
+	dev_dbg(xcsc->xvip.dev, "Performing RGB to YCrCb BT 709");
+	xcsc_copy_coeff(temp, rgb_to_ycrcb_unity);
+	temp[0][3] = 16 * bpc_scale;
+	temp[1][3] = 128 * bpc_scale;
+	temp[2][3] = 128 * bpc_scale;
+	*clip_max = BIT(xcsc->color_depth) - 1;
+}
+
+static int xcsc_update_formats(struct xcsc_dev *xcsc)
+{
+	u32 color_in, color_out;
+
+	/* Write In and Out Video Formats */
+	color_in = xcsc->formats[XVIP_PAD_SINK].code;
+	color_out = xcsc->formats[XVIP_PAD_SOURCE].code;
+
+	switch (color_in) {
+	case MEDIA_BUS_FMT_RBG888_1X24:
+	case MEDIA_BUS_FMT_RBG101010_1X30:
+		dev_dbg(xcsc->xvip.dev, "Media Format In : RGB");
+		xcsc->cft_in = XVIDC_CSF_RGB;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+	case MEDIA_BUS_FMT_VUY10_1X30:
+		dev_dbg(xcsc->xvip.dev, "Media Format In : YUV 444");
+		xcsc->cft_in = XVIDC_CSF_YCRCB_444;
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+		dev_dbg(xcsc->xvip.dev, "Media Format In : YUV 422");
+		xcsc->cft_in = XVIDC_CSF_YCRCB_422;
+		break;
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+	case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		dev_dbg(xcsc->xvip.dev, "Media Format In : YUV 420");
+		xcsc->cft_in = XVIDC_CSF_YCRCB_420;
+		break;
+	}
+
+	switch (color_out) {
+	case MEDIA_BUS_FMT_RBG888_1X24:
+	case MEDIA_BUS_FMT_RBG101010_1X30:
+		xcsc->cft_out = XVIDC_CSF_RGB;
+		dev_dbg(xcsc->xvip.dev, "Media Format Out : RGB");
+		if (color_in != MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_ycrcb_to_rgb(xcsc, &xcsc->clip_max, xcsc->k_hw);
+		else
+			xcsc_set_unity_matrix(xcsc);
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+	case MEDIA_BUS_FMT_VUY10_1X30:
+		xcsc->cft_out = XVIDC_CSF_YCRCB_444;
+		dev_dbg(xcsc->xvip.dev, "Media Format Out : YUV 444");
+		if (color_in == MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_rgb_to_ycrcb(xcsc, &xcsc->clip_max, xcsc->k_hw);
+		else
+			xcsc_set_unity_matrix(xcsc);
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+		xcsc->cft_out = XVIDC_CSF_YCRCB_422;
+		dev_dbg(xcsc->xvip.dev, "Media Format Out : YUV 422");
+		if (color_in == MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_rgb_to_ycrcb(xcsc, &xcsc->clip_max, xcsc->k_hw);
+		else
+			xcsc_set_unity_matrix(xcsc);
+		break;
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+	case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		xcsc->cft_out = XVIDC_CSF_YCRCB_420;
+		dev_dbg(xcsc->xvip.dev, "Media Format Out : YUV 420");
+		if (color_in ==  MEDIA_BUS_FMT_RBG888_1X24)
+			xcsc_rgb_to_ycrcb(xcsc, &xcsc->clip_max, xcsc->k_hw);
+		else
+			xcsc_set_unity_matrix(xcsc);
+		break;
+	}
+
+	xcsc_write(xcsc, XV_CSC_INVIDEOFORMAT, xcsc->cft_in);
+	xcsc_write(xcsc, XV_CSC_OUTVIDEOFORMAT, xcsc->cft_out);
+
+	xcsc_write_coeff(xcsc);
+
+	xcsc_write(xcsc, XV_CSC_CLIPMAX, xcsc->clip_max);
+	xcsc_write(xcsc, XV_CSC_CLAMPMIN, XCSC_CLAMP_MIN_ZERO);
+#ifdef DEBUG
+	xcsc_print_k_hw(xcsc);
+	xcsc_print_coeff(xcsc);
+#endif
+	return 0;
+}
+
+static inline struct xcsc_dev *to_csc(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xcsc_dev, xvip.subdev);
+}
+
+static struct v4l2_mbus_framefmt *
+__xcsc_get_pad_format(struct xcsc_dev *xcsc,
+		      struct v4l2_subdev_state *sd_state,
+		      unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xcsc->xvip.subdev,
+						    sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xcsc->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static void
+xcsc_correct_coeff(struct xcsc_dev *xcsc,
+		   s32 temp[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1])
+{
+	s32 csc_change[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1] = { {0} };
+	s32 csc_extra[XV_CSC_K_MAX_ROWS][XV_CSC_K_MAX_COLUMNS + 1] = { {0} };
+	u32 mbus_in = xcsc->formats[XVIP_PAD_SINK].code;
+	u32 mbus_out = xcsc->formats[XVIP_PAD_SOURCE].code;
+
+#ifdef DEBUG
+	xcsc_log_coeff(xcsc->xvip.dev, temp);
+#endif
+	if (mbus_in == MEDIA_BUS_FMT_RBG888_1X24 && mbus_out == mbus_in) {
+		dev_dbg(xcsc->xvip.dev, "%s : RGB to RGB", __func__);
+		xcsc_copy_coeff(xcsc->k_hw,
+				(const s32 (*)[XV_CSC_K_MAX_COLUMNS + 1])temp);
+	} else if (mbus_in == MEDIA_BUS_FMT_RBG888_1X24 &&
+		   mbus_out != MEDIA_BUS_FMT_RBG888_1X24) {
+		dev_dbg(xcsc->xvip.dev, "%s : RGB to YUV", __func__);
+		xcsc_rgb_to_ycrcb(xcsc, &xcsc->clip_max, csc_change);
+		xcsc_matrix_multiply(temp, csc_change, xcsc->k_hw);
+	} else if (mbus_in != MEDIA_BUS_FMT_RBG888_1X24 &&
+		   mbus_out == MEDIA_BUS_FMT_RBG888_1X24) {
+		dev_dbg(xcsc->xvip.dev, "%s : YUV to RGB", __func__);
+		xcsc_ycrcb_to_rgb(xcsc, &xcsc->clip_max, csc_change);
+		xcsc_matrix_multiply(csc_change, temp, xcsc->k_hw);
+	} else if (mbus_in != MEDIA_BUS_FMT_RBG888_1X24 &&
+		   mbus_out != MEDIA_BUS_FMT_RBG888_1X24) {
+		dev_dbg(xcsc->xvip.dev, "%s : YUV to YUV", __func__);
+		xcsc_ycrcb_to_rgb(xcsc, &xcsc->clip_max, csc_change);
+		xcsc_matrix_multiply(csc_change, temp, csc_extra);
+		xcsc_rgb_to_ycrcb(xcsc, &xcsc->clip_max, csc_change);
+		xcsc_matrix_multiply(csc_extra, csc_change, xcsc->k_hw);
+	} else {
+		/* Should never get here */
+		WARN_ON(1);
+	}
+}
+
+static void xcsc_set_brightness(struct xcsc_dev *xcsc)
+{
+	unsigned int i, j;
+
+	dev_dbg(xcsc->xvip.dev,
+		"%s : Brightness %d Brightness Active %d",
+		__func__,
+		((xcsc->brightness - 20) / 2),
+		((xcsc->brightness_active - 20) / 2));
+	if (xcsc->brightness == xcsc->brightness_active)
+		return;
+	for (i = 0; i < XV_CSC_K_MAX_ROWS; i++) {
+		for (j = 0; j < XV_CSC_K_MAX_COLUMNS; j++) {
+			xcsc->shadow_coeff[i][j] = (xcsc->shadow_coeff[i][j] *
+						    xcsc->brightness) /
+						    xcsc->brightness_active;
+		}
+	}
+	xcsc->brightness_active = xcsc->brightness;
+	xcsc_correct_coeff(xcsc, xcsc->shadow_coeff);
+	xcsc_write_coeff(xcsc);
+#ifdef DEBUG
+	xcsc_print_k_hw(xcsc);
+	xcsc_print_coeff(xcsc);
+#endif
+}
+
+static void xcsc_set_contrast(struct xcsc_dev *xcsc)
+{
+	s32 contrast;
+	u8 scale = BIT(xcsc->color_depth - 8);
+
+	contrast = xcsc->contrast - xcsc->contrast_active;
+	dev_dbg(xcsc->xvip.dev,
+		"%s : Contrast Difference %d scale = %d",
+		__func__, contrast, scale);
+	/* Avoid updates if same */
+	if (!contrast)
+		return;
+	/* Update RGB Offsets */
+	xcsc->shadow_coeff[0][3] += contrast * scale;
+	xcsc->shadow_coeff[1][3] += contrast * scale;
+	xcsc->shadow_coeff[2][3] += contrast * scale;
+	xcsc->contrast_active = xcsc->contrast;
+	xcsc_correct_coeff(xcsc, xcsc->shadow_coeff);
+	xcsc_write_coeff(xcsc);
+#ifdef DEBUG
+	xcsc_print_k_hw(xcsc);
+	xcsc_print_coeff(xcsc);
+#endif
+}
+
+static void xcsc_set_red_gain(struct xcsc_dev *xcsc)
+{
+	dev_dbg(xcsc->xvip.dev,
+		"%s: Red Gain %d Red Gain Active %d", __func__,
+		(xcsc->red_gain - 20) / 2,
+		(xcsc->red_gain_active - 20) / 2);
+
+	if (xcsc->red_gain != xcsc->red_gain_active) {
+		xcsc->shadow_coeff[0][0] = (xcsc->shadow_coeff[0][0] *
+					    xcsc->red_gain) /
+					    xcsc->red_gain_active;
+		xcsc->shadow_coeff[0][1] = (xcsc->shadow_coeff[0][1] *
+					    xcsc->red_gain) /
+					    xcsc->red_gain_active;
+		xcsc->shadow_coeff[0][2] = (xcsc->shadow_coeff[0][2] *
+					    xcsc->red_gain) /
+					    xcsc->red_gain_active;
+		xcsc->red_gain_active = xcsc->red_gain;
+		xcsc_correct_coeff(xcsc, xcsc->shadow_coeff);
+		xcsc_write_coeff(xcsc);
+	}
+#ifdef DEBUG
+	xcsc_print_k_hw(xcsc);
+	xcsc_print_coeff(xcsc);
+#endif
+}
+
+static void xcsc_set_green_gain(struct xcsc_dev *xcsc)
+{
+	dev_dbg(xcsc->xvip.dev,
+		"%s: Green Gain %d Green Gain Active %d", __func__,
+		 (xcsc->green_gain - 20) / 2,
+		 (xcsc->green_gain_active - 20) / 2);
+
+	if (xcsc->green_gain != xcsc->green_gain_active) {
+		xcsc->shadow_coeff[1][0] = (xcsc->shadow_coeff[1][0] *
+					    xcsc->green_gain) /
+					    xcsc->green_gain_active;
+		xcsc->shadow_coeff[1][1] = (xcsc->shadow_coeff[1][1] *
+					    xcsc->green_gain) /
+					    xcsc->green_gain_active;
+		xcsc->shadow_coeff[1][2] = (xcsc->shadow_coeff[1][2] *
+					    xcsc->green_gain) /
+					    xcsc->green_gain_active;
+		xcsc->green_gain_active = xcsc->green_gain;
+		xcsc_correct_coeff(xcsc, xcsc->shadow_coeff);
+		xcsc_write_coeff(xcsc);
+	}
+#ifdef DEBUG
+	xcsc_print_k_hw(xcsc);
+	xcsc_print_coeff(xcsc);
+#endif
+}
+
+static void xcsc_set_blue_gain(struct xcsc_dev *xcsc)
+{
+	dev_dbg(xcsc->xvip.dev,
+		"%s: Blue Gain %d Blue Gain Active %d", __func__,
+		 (xcsc->blue_gain - 20) / 2,
+		 (xcsc->blue_gain_active - 20) / 2);
+
+	if (xcsc->blue_gain != xcsc->blue_gain_active) {
+		xcsc->shadow_coeff[2][0] = (xcsc->shadow_coeff[2][0] *
+					    xcsc->blue_gain) /
+					     xcsc->blue_gain_active;
+		xcsc->shadow_coeff[2][1] = (xcsc->shadow_coeff[2][1] *
+					    xcsc->blue_gain) /
+					     xcsc->blue_gain_active;
+		xcsc->shadow_coeff[2][2] = (xcsc->shadow_coeff[2][2] *
+					    xcsc->blue_gain) /
+					     xcsc->blue_gain_active;
+		xcsc->blue_gain_active = xcsc->blue_gain;
+		xcsc_correct_coeff(xcsc, xcsc->shadow_coeff);
+		xcsc_write_coeff(xcsc);
+	}
+#ifdef DEBUG
+	xcsc_print_k_hw(xcsc);
+	xcsc_print_coeff(xcsc);
+#endif
+}
+
+static void xcsc_set_size(struct xcsc_dev *xcsc)
+{
+	u32 width, height;
+
+	width = xcsc->formats[XVIP_PAD_SINK].width;
+	height = xcsc->formats[XVIP_PAD_SINK].height;
+	dev_dbg(xcsc->xvip.dev, "%s : Setting width %d and height %d",
+		__func__, width, height);
+	xcsc_write(xcsc, XV_CSC_WIDTH, width);
+	xcsc_write(xcsc, XV_CSC_HEIGHT, height);
+}
+
+static int xcsc_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xcsc_dev *xcsc = to_csc(subdev);
+
+	dev_dbg(xcsc->xvip.dev, "%s : Stream %s", __func__,
+		enable ? "On" : "Off");
+	if (!enable) {
+		/* Reset the Global IP Reset through PS GPIO */
+		gpiod_set_value_cansleep(xcsc->rst_gpio, XCSC_RESET_ASSERT);
+		gpiod_set_value_cansleep(xcsc->rst_gpio, XCSC_RESET_DEASSERT);
+
+		/* Reset the active controls */
+		xcsc->brightness_active	= 120;
+		xcsc->contrast_active = 0;
+		xcsc->red_gain_active = 120;
+		xcsc->blue_gain_active = 120;
+		xcsc->green_gain_active = 120;
+		xcsc_copy_coeff(xcsc->shadow_coeff, rgb_unity_matrix);
+
+		return 0;
+	}
+	/* Set the controls */
+	xcsc_set_brightness(xcsc);
+	xcsc_set_contrast(xcsc);
+	xcsc_set_red_gain(xcsc);
+	xcsc_set_green_gain(xcsc);
+	xcsc_set_blue_gain(xcsc);
+
+	xcsc_write(xcsc, XV_CSC_INVIDEOFORMAT, xcsc->cft_in);
+	xcsc_write(xcsc, XV_CSC_OUTVIDEOFORMAT, xcsc->cft_out);
+	xcsc_write(xcsc, XV_CSC_CLIPMAX, xcsc->clip_max);
+	xcsc_write(xcsc, XV_CSC_CLAMPMIN, XCSC_CLAMP_MIN_ZERO);
+	xcsc_set_size(xcsc);
+	xcsc_write_coeff(xcsc);
+#ifdef DEBUG
+	xcsc_print_coeff(xcsc);
+	dev_dbg(xcsc->xvip.dev, "cft_in = %d cft_out = %d",
+		xcsc_read(xcsc, XV_CSC_INVIDEOFORMAT),
+		xcsc_read(xcsc, XV_CSC_OUTVIDEOFORMAT));
+	dev_dbg(xcsc->xvip.dev, "clipmax = %d clampmin = %d",
+		xcsc_read(xcsc, XV_CSC_CLIPMAX),
+		xcsc_read(xcsc, XV_CSC_CLAMPMIN));
+	dev_dbg(xcsc->xvip.dev, "height = %d width = %d",
+		xcsc_read(xcsc, XV_CSC_HEIGHT),
+		xcsc_read(xcsc, XV_CSC_WIDTH));
+#endif
+	/* Start VPSS CSC IP */
+	xcsc_write(xcsc, XV_CSC_AP_CTRL, XCSC_STREAM_ON);
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops xcsc_video_ops = {
+	.s_stream = xcsc_s_stream,
+};
+
+static int xcsc_get_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xcsc_dev *xcsc = to_csc(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xcsc_get_pad_format(xcsc, sd_state, fmt->pad, fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+	return 0;
+}
+
+static int xcsc_set_format(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_state *sd_state,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xcsc_dev *xcsc = to_csc(subdev);
+	struct v4l2_mbus_framefmt *__format;
+	struct v4l2_mbus_framefmt *__propagate;
+
+	__format = __xcsc_get_pad_format(xcsc, sd_state, fmt->pad, fmt->which);
+	if (!__format)
+		return -EINVAL;
+
+	/* Propagate to Source Pad */
+	__propagate = __xcsc_get_pad_format(xcsc, sd_state,
+					    XVIP_PAD_SOURCE, fmt->which);
+	if (!__propagate)
+		return -EINVAL;
+
+	*__format = fmt->format;
+
+	__format->width = clamp_t(unsigned int, fmt->format.width,
+				  XV_CSC_MIN_WIDTH, xcsc->max_width);
+	__format->height = clamp_t(unsigned int, fmt->format.height,
+				   XV_CSC_MIN_HEIGHT, xcsc->max_height);
+
+	switch (__format->code) {
+	case MEDIA_BUS_FMT_VUY8_1X24:
+	case MEDIA_BUS_FMT_RBG888_1X24:
+	case MEDIA_BUS_FMT_RBG101010_1X30:
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+	case MEDIA_BUS_FMT_VYYUYY10_4X20:
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+	case MEDIA_BUS_FMT_VUY10_1X30:
+		break;
+	default:
+		/* Unsupported Format. Default to RGB */
+		__format->code = MEDIA_BUS_FMT_RBG888_1X24;
+		return -EINVAL;
+	}
+
+	/* Always propagate Sink image size to Source */
+	__propagate->width  = __format->width;
+	__propagate->height = __format->height;
+
+	fmt->format = *__format;
+	xcsc_update_formats(xcsc);
+	dev_info(xcsc->xvip.dev, "VPSS CSC color controls reset to defaults");
+	return 0;
+}
+
+static const struct v4l2_subdev_pad_ops xcsc_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xcsc_get_format,
+	.set_fmt = xcsc_set_format,
+};
+
+static const struct v4l2_subdev_ops xcsc_ops = {
+	.video = &xcsc_video_ops,
+	.pad = &xcsc_pad_ops
+};
+
+static int xcsc_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct xcsc_dev *xcsc = container_of(ctrl->handler,
+					struct xcsc_dev,
+					ctrl_handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_XILINX_CSC_BRIGHTNESS:
+		xcsc->brightness = (2 * ctrl->val) + 20;
+		break;
+	case V4L2_CID_XILINX_CSC_CONTRAST:
+		xcsc->contrast = (4 * ctrl->val) - 200;
+		break;
+	case V4L2_CID_XILINX_CSC_RED_GAIN:
+		xcsc->red_gain =  (2 * ctrl->val) + 20;
+		break;
+	case V4L2_CID_XILINX_CSC_BLUE_GAIN:
+		xcsc->blue_gain =  (2 * ctrl->val) + 20;
+		break;
+	case V4L2_CID_XILINX_CSC_GREEN_GAIN:
+		xcsc->green_gain =  (2 * ctrl->val) + 20;
+		break;
+	}
+	return 0;
+}
+
+static const struct v4l2_ctrl_ops xcsc_ctrl_ops = {
+	.s_ctrl = xcsc_s_ctrl,
+};
+
+static struct v4l2_ctrl_config xcsc_color_ctrls[XCSC_COLOR_CTRL_COUNT] = {
+	/* Brightness */
+	{
+		.ops = &xcsc_ctrl_ops,
+		.id = V4L2_CID_XILINX_CSC_BRIGHTNESS,
+		.name = "CSC Brightness",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.max = 100,
+		.step = 1,
+		.def = XCSC_COLOR_CTRL_DEFAULT,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+	/* Contrast */
+	{
+		.ops = &xcsc_ctrl_ops,
+		.id = V4L2_CID_XILINX_CSC_CONTRAST,
+		.name = "CSC Contrast",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.max = 100,
+		.step = 1,
+		.def = XCSC_COLOR_CTRL_DEFAULT,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+	/* Red Gain */
+	{
+		.ops = &xcsc_ctrl_ops,
+		.id = V4L2_CID_XILINX_CSC_RED_GAIN,
+		.name = "CSC Red Gain",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.max = 100,
+		.step = 1,
+		.def = XCSC_COLOR_CTRL_DEFAULT,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+	/* Blue Gain */
+	{
+		.ops = &xcsc_ctrl_ops,
+		.id = V4L2_CID_XILINX_CSC_BLUE_GAIN,
+		.name = "CSC Blue Gain",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.max = 100,
+		.step = 1,
+		.def = XCSC_COLOR_CTRL_DEFAULT,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+	/* Green Gain */
+	{
+		.ops = &xcsc_ctrl_ops,
+		.id = V4L2_CID_XILINX_CSC_GREEN_GAIN,
+		.name = "CSC Green Gain",
+		.type = V4L2_CTRL_TYPE_INTEGER,
+		.min = 0,
+		.max = 100,
+		.step = 1,
+		.def = XCSC_COLOR_CTRL_DEFAULT,
+		.flags = V4L2_CTRL_FLAG_SLIDER,
+	},
+};
+
+static int xcsc_open(struct v4l2_subdev *subdev,
+		     struct v4l2_subdev_fh *fh)
+{
+	struct xcsc_dev *xcsc = to_csc(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xcsc->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state,
+					    XVIP_PAD_SOURCE);
+	*format = xcsc->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int xcsc_close(struct v4l2_subdev *subdev,
+		      struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static const struct v4l2_subdev_internal_ops xcsc_internal_ops = {
+	.open  = xcsc_open,
+	.close = xcsc_close,
+};
+
+static const struct media_entity_operations xcsc_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static int xcsc_parse_of(struct xcsc_dev *xcsc)
+{
+	struct device *dev = xcsc->xvip.dev;
+	struct device_node *node = xcsc->xvip.dev->of_node;
+	const struct xvip_video_format *vip_format;
+	struct device_node *ports, *port;
+	int rval;
+	u32 port_id = 0;
+	u32 video_width[2] = {0};
+
+	rval = of_property_read_u32(node, "xlnx,max-height", &xcsc->max_height);
+	if (rval < 0) {
+		dev_err(dev, "xlnx,max-height is missing!");
+		return -EINVAL;
+	} else if (xcsc->max_height > XV_CSC_MAX_HEIGHT ||
+		   xcsc->max_height < XV_CSC_MIN_HEIGHT) {
+		dev_err(dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	rval = of_property_read_u32(node, "xlnx,max-width", &xcsc->max_width);
+	if (rval < 0) {
+		dev_err(dev, "xlnx,max-width is missing!");
+		return -EINVAL;
+	} else if (xcsc->max_width > XV_CSC_MAX_WIDTH ||
+		   xcsc->max_width < XV_CSC_MIN_WIDTH) {
+		dev_err(dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "Invalid media pad format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			rval = of_property_read_u32(port, "reg", &port_id);
+			if (rval < 0) {
+				dev_err(dev, "No reg in DT to specify pad");
+				return rval;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "Invalid reg in DT");
+				return -EINVAL;
+			}
+			xcsc->vip_formats[port_id] = vip_format;
+
+			rval = of_property_read_u32(port, "xlnx,video-width",
+						    &video_width[port_id]);
+			if (rval < 0) {
+				dev_err(dev,
+					"DT Port%d xlnx,video-width not found",
+					port_id);
+				return rval;
+			}
+		}
+	}
+	if (video_width[0] != video_width[1]) {
+		dev_err(dev, "Changing video width in DT not supported");
+		return -EINVAL;
+	}
+	switch (video_width[0]) {
+	case XVIDC_BPC_8:
+		xcsc->color_depth = XVIDC_BPC_8;
+		break;
+	case XVIDC_BPC_10:
+		xcsc->color_depth = XVIDC_BPC_10;
+		break;
+	default:
+		dev_err(dev, "Unsupported color depth %d", video_width[0]);
+		return -EINVAL;
+	}
+	/* Reset GPIO */
+	xcsc->rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(xcsc->rst_gpio)) {
+		if (PTR_ERR(xcsc->rst_gpio) != -EPROBE_DEFER)
+			dev_err(dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(xcsc->rst_gpio);
+	}
+	return 0;
+}
+
+static int xcsc_probe(struct platform_device *pdev)
+{
+	struct xcsc_dev *xcsc;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *def_fmt;
+	int rval, itr;
+
+	xcsc = devm_kzalloc(&pdev->dev, sizeof(*xcsc), GFP_KERNEL);
+	if (!xcsc)
+		return -ENOMEM;
+
+	xcsc->xvip.dev = &pdev->dev;
+
+	rval = xcsc_parse_of(xcsc);
+	if (rval < 0)
+		return rval;
+
+	/* Reset and initialize the core */
+	gpiod_set_value_cansleep(xcsc->rst_gpio, XCSC_RESET_DEASSERT);
+	rval = xvip_init_resources(&xcsc->xvip);
+	if (rval < 0)
+		return rval;
+
+	/* Init v4l2 subdev */
+	subdev = &xcsc->xvip.subdev;
+	v4l2_subdev_init(subdev, &xcsc_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xcsc_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xcsc);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Default Formats Initialization */
+	xcsc_set_default_state(xcsc);
+	def_fmt = &xcsc->default_formats[XVIP_PAD_SINK];
+	def_fmt->code = xcsc->vip_formats[XVIP_PAD_SINK]->code;
+	def_fmt->field = V4L2_FIELD_NONE;
+	def_fmt->colorspace = V4L2_COLORSPACE_REC709;
+	def_fmt->width = XV_CSC_DEFAULT_WIDTH;
+	def_fmt->height = XV_CSC_DEFAULT_HEIGHT;
+	xcsc->formats[XVIP_PAD_SINK] = *def_fmt;
+	/* Source supports only YUV 444, YUV 422, and RGB */
+	def_fmt = &xcsc->default_formats[XVIP_PAD_SOURCE];
+	*def_fmt = xcsc->default_formats[XVIP_PAD_SINK];
+	def_fmt->code = xcsc->vip_formats[XVIP_PAD_SOURCE]->code;
+	def_fmt->width = XV_CSC_DEFAULT_WIDTH;
+	def_fmt->height = XV_CSC_DEFAULT_HEIGHT;
+	xcsc->formats[XVIP_PAD_SOURCE] = *def_fmt;
+	xcsc->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xcsc->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Init Media Entity */
+	subdev->entity.ops = &xcsc_media_ops;
+	rval = media_entity_pads_init(&subdev->entity, 2, xcsc->pads);
+	if (rval < 0)
+		goto media_error;
+	/* V4L2 Control Setup */
+	v4l2_ctrl_handler_init(&xcsc->ctrl_handler,
+			       ARRAY_SIZE(xcsc_color_ctrls));
+	for (itr = 0; itr < ARRAY_SIZE(xcsc_color_ctrls); itr++) {
+		xcsc->custom_ctrls[itr] =
+			v4l2_ctrl_new_custom(&xcsc->ctrl_handler,
+					     &xcsc_color_ctrls[itr], NULL);
+	}
+	if (xcsc->ctrl_handler.error) {
+		dev_err(&pdev->dev, "Failed to add  v4l2 controls");
+		rval = xcsc->ctrl_handler.error;
+		goto ctrl_error;
+	}
+	subdev->ctrl_handler = &xcsc->ctrl_handler;
+	rval = v4l2_ctrl_handler_setup(&xcsc->ctrl_handler);
+	if (rval < 0) {
+		dev_err(xcsc->xvip.dev, "Failed to setup control handler");
+		goto ctrl_error;
+	}
+	platform_set_drvdata(pdev, xcsc);
+	rval = v4l2_async_register_subdev(subdev);
+	if (rval < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		goto ctrl_error;
+	}
+	dev_info(&pdev->dev, "VPSS CSC %d-bit Color Depth Probe Successful",
+		 xcsc->color_depth);
+	return 0;
+ctrl_error:
+	v4l2_ctrl_handler_free(&xcsc->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+media_error:
+	xvip_cleanup_resources(&xcsc->xvip);
+	return rval;
+}
+
+static int xcsc_remove(struct platform_device *pdev)
+{
+	struct xcsc_dev *xcsc = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xcsc->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&xcsc->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xcsc->xvip);
+	return 0;
+}
+
+static const struct of_device_id xcsc_of_id_table[] = {
+	{.compatible = "xlnx,v-vpss-csc"},
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, xcsc_of_id_table);
+
+static struct platform_driver xcsc_driver = {
+	.driver = {
+		.name = "xilinx-vpss-csc",
+		.of_match_table = xcsc_of_id_table,
+	},
+	.probe = xcsc_probe,
+	.remove = xcsc_remove,
+};
+
+module_platform_driver(xcsc_driver);
+MODULE_DESCRIPTION("Xilinx VPSS CSC Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vpss-scaler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vpss-scaler.c
@@ -0,0 +1,2125 @@
+/*
+ * Xilinx VPSS Scaler
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+#include "xilinx-vip.h"
+
+#define XSCALER_MIN_WIDTH		(64)
+#define XSCALER_MAX_WIDTH		(8192)
+#define XSCALER_MIN_HEIGHT		(64)
+#define XSCALER_MAX_HEIGHT		(4320)
+#define XSCALER_MAX_PHASES		(64)
+
+/* Modify to defaults incase it is not configured from application */
+#define XSCALER_DEF_IN_HEIGHT		(720)
+#define XSCALER_DEF_IN_WIDTH		(1280)
+#define XSCALER_DEF_OUT_HEIGHT		(1080)
+#define XSCALER_DEF_OUT_WIDTH		(1920)
+
+#define XSCALER_HSF			(0x0100)
+#define XSCALER_VSF			(0x0104)
+#define XSCALER_SF_SHIFT		(20)
+#define XSCALER_SF_MASK			(0xffffff)
+#define XSCALER_SOURCE_SIZE		(0x0108)
+#define XSCALER_SIZE_HORZ_SHIFT		(0)
+#define XSCALER_SIZE_VERT_SHIFT		(16)
+#define XSCALER_SIZE_MASK		(0xfff)
+#define XSCALER_HAPERTURE		(0x010c)
+#define XSCALER_VAPERTURE		(0x0110)
+#define XSCALER_APERTURE_START_SHIFT	(0)
+#define XSCALER_APERTURE_END_SHIFT	(16)
+#define XSCALER_OUTPUT_SIZE		(0x0114)
+#define XSCALER_COEF_DATA_IN		(0x0134)
+#define XSCALER_BITSHIFT_16		(16)
+
+/* Video subsytems block offset */
+#define S_AXIS_RESET_OFF	(0x00010000)
+#define V_HSCALER_OFF		(0x00000000)
+#define V_VSCALER_OFF		(0x00020000)
+
+/* HW Reset Network GPIO Channel */
+#define XGPIO_CH_RESET_SEL		(1)
+#define XGPIO_RESET_MASK_VIDEO_IN	BIT(0)
+#define XGPIO_RESET_MASK_IP_AXIS	BIT(1)
+#define XGPIO_RESET_MASK_IP_AXIMM	BIT(0)
+#define XGPIO_RESET_MASK_ALL_BLOCKS	(XGPIO_RESET_MASK_VIDEO_IN  | \
+						XGPIO_RESET_MASK_IP_AXIS)
+#define XGPIO_DATA_OFFSET		(0x0)
+#define XGPIO_TRI_OFFSET		(0x4)
+#define XGPIO_DATA2_OFFSET		(0x8)
+#define XGPIO_TRI2_OFFSET		(0xc)
+
+#define XGPIO_GIE_OFFSET		(0x11c)
+#define XGPIO_ISR_OFFSET		(0x120)
+#define XGPIO_IER_OFFSET		(0x128)
+#define XGPIO_CHAN_OFFSET		(8)
+#define STEP_PRECISION			(65536)
+
+/* Video IP Formats */
+enum xscaler_vid_reg_fmts {
+	XVIDC_CSF_RGB = 0,
+	XVIDC_CSF_YCRCB_444,
+	XVIDC_CSF_YCRCB_422,
+	XVIDC_CSF_YCRCB_420,
+};
+
+/* Video IP PPC */
+#define XSCALER_PPC_1			(1)
+#define XSCALER_PPC_2			(2)
+#define XSCALER_PPC_4			(4)
+
+#define XV_HSCALER_MAX_H_TAPS           (12)
+#define XV_HSCALER_MAX_H_PHASES         (64)
+#define XV_HSCALER_MAX_LINE_WIDTH       (3840)
+#define XV_VSCALER_MAX_V_TAPS           (12)
+#define XV_VSCALER_MAX_V_PHASES         (64)
+
+#define XV_HSCALER_TAPS_2		(2)
+#define XV_HSCALER_TAPS_4		(4)
+#define XV_HSCALER_TAPS_6		(6)
+#define XV_HSCALER_TAPS_8		(8)
+#define XV_HSCALER_TAPS_10		(10)
+#define XV_HSCALER_TAPS_12		(12)
+#define XV_VSCALER_TAPS_2		(2)
+#define XV_VSCALER_TAPS_4		(4)
+#define XV_VSCALER_TAPS_6		(6)
+#define XV_VSCALER_TAPS_8		(8)
+#define XV_VSCALER_TAPS_10		(10)
+#define XV_VSCALER_TAPS_12		(12)
+
+/* Mask definitions for Low and high 16 bits in a 32 bit number */
+#define XHSC_MASK_LOW_16BITS		GENMASK(15, 0)
+#define XHSC_MASK_HIGH_16BITS		GENMASK(31, 16)
+#define XHSC_MASK_LOW_32BITS		GENMASK(31, 0)
+#define XHSC_STEP_PRECISION_SHIFT	(16)
+#define XHSC_HPHASE_SHIFT_BY_6		(6)
+#define XHSC_HPHASE_MULTIPLIER		(9)
+#define XHSC_HPHASE_MUL_4PPC		(10)
+
+/* Mask definitions for Low and high 16 bits in a 32 bit number */
+#define XVSC_MASK_LOW_16BITS            GENMASK(15, 0)
+#define XVSC_MASK_HIGH_16BITS           GENMASK(31, 16)
+
+/* XSCALER POWER MACROS */
+#define XSCALER_RESET_ASSERT	(0x1)
+#define XSCALER_RESET_DEASSERT	(0x0)
+
+/* Scaler AP Control Registers */
+#define XSCALER_START		BIT(0)
+#define XSCALER_AUTO_RESTART	BIT(7)
+#define XSCALER_STREAM_ON	(XSCALER_START | XSCALER_AUTO_RESTART)
+
+/* H-scaler registers */
+#define XV_HSCALER_CTRL_ADDR_AP_CTRL				(0x0000)
+#define XV_HSCALER_CTRL_ADDR_GIE				(0x0004)
+#define XV_HSCALER_CTRL_ADDR_IER				(0x0008)
+#define XV_HSCALER_CTRL_ADDR_ISR				(0x000c)
+#define XV_HSCALER_CTRL_ADDR_HWREG_HEIGHT_DATA			(0x0010)
+#define XV_HSCALER_CTRL_ADDR_HWREG_WIDTHIN_DATA			(0x0018)
+#define XV_HSCALER_CTRL_ADDR_HWREG_WIDTHOUT_DATA		(0x0020)
+#define XV_HSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA		(0x0028)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PIXELRATE_DATA		(0x0030)
+#define XV_HSCALER_CTRL_ADDR_HWREG_COLORMODEOUT_DATA		(0X0038)
+#define XV_HSCALER_CTRL_ADDR_HWREG_HFLTCOEFF_BASE		(0x0800)
+#define XV_HSCALER_CTRL_ADDR_HWREG_HFLTCOEFF_HIGH		(0x0bff)
+
+/* Coefficients for 6, 8, 10 and 12 tap filters */
+
+static const s16 XV_lanczos2_taps6[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{   0,    0, 4096,    0,    0,   0, },
+	{   0,  -40, 4099,   42,    0,  -5, },
+	{  -1,  -77, 4097,   87,   -1,  -9, },
+	{  -2, -111, 4092,  134,   -2, -15, },
+	{  -4, -143, 4082,  184,   -4, -19, },
+	{  -6, -173, 4068,  237,   -7, -23, },
+	{  -8, -201, 4051,  292,  -10, -28, },
+	{ -11, -226, 4029,  350,  -13, -33, },
+	{ -14, -248, 4003,  411,  -18, -38, },
+	{ -17, -269, 3974,  474,  -23, -43, },
+	{ -21, -287, 3940,  539,  -28, -47, },
+	{ -24, -303, 3903,  608,  -34, -54, },
+	{ -28, -317, 3862,  678,  -41, -58, },
+	{ -32, -329, 3817,  751,  -49, -62, },
+	{ -37, -339, 3768,  826,  -57, -65, },
+	{ -41, -347, 3716,  903,  -65, -70, },
+	{ -45, -353, 3661,  982,  -75, -74, },
+	{ -50, -358, 3602, 1063,  -84, -77, },
+	{ -54, -361, 3539, 1146,  -95, -79, },
+	{ -58, -362, 3474, 1230, -106, -82, },
+	{ -62, -361, 3406, 1317, -117, -87, },
+	{ -66, -359, 3335, 1404, -128, -90, },
+	{ -70, -356, 3261, 1493, -140, -92, },
+	{ -74, -351, 3185, 1583, -153, -94, },
+	{ -77, -346, 3106, 1673, -165, -95, },
+	{ -81, -339, 3025, 1765, -178, -96, },
+	{ -84, -331, 2942, 1857, -191, -97, },
+	{ -87, -322, 2858, 1950, -204, -99, },
+	{ -89, -313, 2771, 2043, -217, -99, },
+	{ -92, -302, 2683, 2136, -230, -99, },
+	{ -94, -292, 2594, 2228, -243, -97, },
+	{ -95, -280, 2504, 2321, -256, -98, },
+	{ -97, -268, 2413, 2413, -268, -97, },
+	{ -97, -256, 2321, 2504, -280, -96, },
+	{ -98, -243, 2228, 2594, -292, -93, },
+	{ -98, -230, 2136, 2683, -302, -93, },
+	{ -98, -217, 2043, 2771, -313, -90, },
+	{ -98, -204, 1950, 2858, -322, -88, },
+	{ -97, -191, 1857, 2942, -331, -84, },
+	{ -96, -178, 1765, 3025, -339, -81, },
+	{ -95, -165, 1673, 3106, -346, -77, },
+	{ -93, -153, 1583, 3185, -351, -75, },
+	{ -91, -140, 1493, 3261, -356, -71, },
+	{ -89, -128, 1404, 3335, -359, -67, },
+	{ -86, -117, 1317, 3406, -361, -63, },
+	{ -83, -106, 1230, 3474, -362, -57, },
+	{ -80,  -95, 1146, 3539, -361, -53, },
+	{ -77,  -84, 1063, 3602, -358, -50, },
+	{ -73,  -75,  982, 3661, -353, -46, },
+	{ -69,  -65,  903, 3716, -347, -42, },
+	{ -65,  -57,  826, 3768, -339, -37, },
+	{ -61,  -49,  751, 3817, -329, -33, },
+	{ -57,  -41,  678, 3862, -317, -29, },
+	{ -52,  -34,  608, 3903, -303, -26, },
+	{ -47,  -28,  539, 3940, -287, -21, },
+	{ -43,  -23,  474, 3974, -269, -17, },
+	{ -38,  -18,  411, 4003, -248, -14, },
+	{ -33,  -13,  350, 4029, -226, -11, },
+	{ -28,  -10,  292, 4051, -201,  -8, },
+	{ -24,   -7,  237, 4068, -173,  -5, },
+	{ -19,   -4,  184, 4082, -143,  -4, },
+	{ -14,   -2,  134, 4092, -111,  -3, },
+	{  -9,   -1,   87, 4097,  -77,  -1, },
+	{  -5,    0,   42, 4099,  -40,   0, }
+};
+
+/* ScalingRatio = 1.25 */
+static const s16 XV_fixedcoeff_taps6_SR1p2[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{ -102,  512, 3208,  512, -102,  68, },
+	{  -97,  471, 3209,  555, -107,  65, },
+	{  -92,  431, 3208,  599, -113,  63, },
+	{  -87,  392, 3205,  645, -118,  59, },
+	{  -82,  354, 3199,  691, -124,  58, },
+	{  -77,  318, 3191,  739, -130,  55, },
+	{  -72,  282, 3181,  788, -136,  53, },
+	{  -68,  248, 3169,  838, -141,  50, },
+	{  -64,  216, 3155,  889, -147,  47, },
+	{  -59,  184, 3139,  941, -153,  44, },
+	{  -55,  154, 3120,  993, -158,  42, },
+	{  -52,  125, 3100, 1047, -164,  40, },
+	{  -48,   98, 3077, 1101, -169,  37, },
+	{  -44,   71, 3052, 1157, -174,  34, },
+	{  -41,   46, 3025, 1212, -180,  34, },
+	{  -38,   23, 2996, 1269, -184,  30, },
+	{  -35,    0, 2965, 1326, -189,  29, },
+	{  -32,  -21, 2933, 1383, -193,  26, },
+	{  -29,  -41, 2898, 1441, -198,  25, },
+	{  -26,  -60, 2862, 1500, -201,  21, },
+	{  -24,  -78, 2823, 1558, -205,  22, },
+	{  -21,  -94, 2784, 1617, -208,  18, },
+	{  -19, -109, 2742, 1676, -210,  16, },
+	{  -17, -123, 2699, 1734, -212,  15, },
+	{  -14, -136, 2654, 1793, -214,  13, },
+	{  -12, -148, 2608, 1852, -214,  10, },
+	{  -10, -159, 2560, 1910, -215,  10, },
+	{   -9, -168, 2512, 1968, -215,   8, },
+	{   -7, -177, 2461, 2026, -214,   7, },
+	{   -5, -185, 2410, 2083, -212,   5, },
+	{   -3, -192, 2358, 2139, -209,   3, },
+	{   -2, -197, 2304, 2195, -206,   2, },
+	{    0, -202, 2250, 2250, -202,   0, },
+	{    2, -206, 2195, 2304, -197,  -2, },
+	{    3, -209, 2139, 2358, -192,  -3, },
+	{    5, -212, 2083, 2410, -185,  -5, },
+	{    6, -214, 2026, 2461, -177,  -6, },
+	{    8, -215, 1968, 2512, -168,  -9, },
+	{   10, -215, 1910, 2560, -159, -10, },
+	{   11, -214, 1852, 2608, -148, -13, },
+	{   13, -214, 1793, 2654, -136, -14, },
+	{   15, -212, 1734, 2699, -123, -17, },
+	{   17, -210, 1676, 2742, -109, -20, },
+	{   18, -208, 1617, 2784,  -94, -21, },
+	{   20, -205, 1558, 2823,  -78, -22, },
+	{   22, -201, 1500, 2862,  -60, -27, },
+	{   24, -198, 1441, 2898,  -41, -28, },
+	{   26, -193, 1383, 2933,  -21, -32, },
+	{   28, -189, 1326, 2965,    0, -34, },
+	{   30, -184, 1269, 2996,   23, -38, },
+	{   33, -180, 1212, 3025,   46, -40, },
+	{   35, -174, 1157, 3052,   71, -45, },
+	{   37, -169, 1101, 3077,   98, -48, },
+	{   40, -164, 1047, 3100,  125, -52, },
+	{   42, -158,  993, 3120,  154, -55, },
+	{   44, -153,  941, 3139,  184, -59, },
+	{   47, -147,  889, 3155,  216, -64, },
+	{   50, -141,  838, 3169,  248, -68, },
+	{   52, -136,  788, 3181,  282, -71, },
+	{   55, -130,  739, 3191,  318, -77, },
+	{   57, -124,  691, 3199,  354, -81, },
+	{   60, -118,  645, 3205,  392, -88, },
+	{   63, -113,  599, 3208,  431, -92, },
+	{   65, -107,  555, 3209,  471, -97, }
+};
+
+/* ScalingRatio = 2.0 */
+static const s16 XV_fixedcoeff_taps6_SR2[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{   0, 970, 2235,  970,   0, -79, },
+	{  -3, 943, 2233,  997,   3, -77, },
+	{  -5, 915, 2231, 1025,   6, -76, },
+	{  -8, 888, 2227, 1052,  10, -73, },
+	{ -10, 861, 2223, 1079,  14, -71, },
+	{ -12, 834, 2218, 1107,  18, -69, },
+	{ -14, 808, 2213, 1134,  22, -67, },
+	{ -15, 782, 2206, 1162,  27, -66, },
+	{ -17, 756, 2199, 1189,  32, -63, },
+	{ -18, 731, 2191, 1217,  37, -62, },
+	{ -20, 706, 2182, 1245,  42, -59, },
+	{ -21, 681, 2172, 1272,  48, -56, },
+	{ -22, 657, 2162, 1300,  55, -56, },
+	{ -22, 633, 2151, 1327,  61, -54, },
+	{ -23, 609, 2139, 1355,  68, -52, },
+	{ -24, 586, 2126, 1382,  76, -50, },
+	{ -25, 564, 2113, 1410,  83, -49, },
+	{ -25, 541, 2099, 1437,  91, -47, },
+	{ -26, 520, 2084, 1464, 100, -46, },
+	{ -26, 498, 2069, 1491, 109, -45, },
+	{ -27, 477, 2053, 1517, 118, -42, },
+	{ -27, 457, 2036, 1544, 128, -42, },
+	{ -27, 437, 2019, 1570, 138, -41, },
+	{ -28, 418, 2001, 1596, 148, -39, },
+	{ -28, 399, 1983, 1622, 160, -40, },
+	{ -29, 380, 1964, 1647, 171, -37, },
+	{ -29, 362, 1944, 1672, 183, -36, },
+	{ -29, 345, 1924, 1697, 195, -36, },
+	{ -30, 328, 1903, 1722, 208, -35, },
+	{ -30, 311, 1882, 1746, 221, -34, },
+	{ -31, 295, 1860, 1770, 235, -33, },
+	{ -31, 279, 1838, 1793, 249, -32, },
+	{ -32, 264, 1816, 1816, 264, -32, },
+	{ -32, 249, 1793, 1838, 279, -31, },
+	{ -33, 235, 1770, 1860, 295, -31, },
+	{ -34, 221, 1746, 1882, 311, -30, },
+	{ -35, 208, 1722, 1903, 328, -30, },
+	{ -35, 195, 1697, 1924, 345, -30, },
+	{ -36, 183, 1672, 1944, 362, -29, },
+	{ -37, 171, 1647, 1964, 380, -29, },
+	{ -38, 160, 1622, 1983, 399, -30, },
+	{ -39, 148, 1596, 2001, 418, -28, },
+	{ -40, 138, 1570, 2019, 437, -28, },
+	{ -42, 128, 1544, 2036, 457, -27, },
+	{ -43, 118, 1517, 2053, 477, -26, },
+	{ -44, 109, 1491, 2069, 498, -27, },
+	{ -46, 100, 1464, 2084, 520, -26, },
+	{ -47,  91, 1437, 2099, 541, -25, },
+	{ -49,  83, 1410, 2113, 564, -25, },
+	{ -50,  76, 1382, 2126, 586, -24, },
+	{ -52,  68, 1355, 2139, 609, -23, },
+	{ -54,  61, 1327, 2151, 633, -22, },
+	{ -55,  55, 1300, 2162, 657, -23, },
+	{ -57,  48, 1272, 2172, 681, -20, },
+	{ -59,  42, 1245, 2182, 706, -20, },
+	{ -61,  37, 1217, 2191, 731, -19, },
+	{ -63,  32, 1189, 2199, 756, -17, },
+	{ -65,  27, 1162, 2206, 782, -16, },
+	{ -67,  22, 1134, 2213, 808, -14, },
+	{ -69,  18, 1107, 2218, 834, -12, },
+	{ -71,  14, 1079, 2223, 861, -10, },
+	{ -73,  10, 1052, 2227, 888,  -8, },
+	{ -75,   6, 1025, 2231, 915,  -6, },
+	{ -77,   3,  997, 2233, 943,  -3, }
+};
+
+/* ScalingRatio = 3.0 */
+static const s16 XV_fixedcoeff_taps6_SR3[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{ 126, 1019, 1806, 1019,  126,   0, },
+	{ 120, 1000, 1805, 1038,  132,   1, },
+	{ 114,  980, 1804, 1057,  138,   3, },
+	{ 108,  961, 1802, 1075,  145,   5, },
+	{ 103,  942, 1800, 1094,  152,   5, },
+	{  98,  922, 1797, 1113,  159,   7, },
+	{  93,  903, 1794, 1131,  167,   8, },
+	{  88,  884, 1790, 1150,  174,  10, },
+	{  84,  865, 1786, 1168,  182,  11, },
+	{  80,  846, 1782, 1187,  191,  10, },
+	{  76,  827, 1777, 1205,  199,  12, },
+	{  72,  809, 1771, 1223,  208,  13, },
+	{  68,  790, 1766, 1241,  217,  14, },
+	{  65,  772, 1759, 1259,  226,  15, },
+	{  61,  753, 1753, 1277,  236,  16, },
+	{  58,  735, 1746, 1295,  246,  16, },
+	{  56,  717, 1738, 1313,  256,  16, },
+	{  53,  699, 1730, 1330,  266,  18, },
+	{  50,  682, 1722, 1347,  277,  18, },
+	{  48,  664, 1713, 1364,  288,  19, },
+	{  46,  647, 1704, 1381,  299,  19, },
+	{  43,  630, 1694, 1398,  311,  20, },
+	{  41,  613, 1684, 1414,  323,  21, },
+	{  40,  596, 1674, 1430,  335,  21, },
+	{  38,  580, 1663, 1446,  347,  22, },
+	{  36,  563, 1652, 1462,  360,  23, },
+	{  35,  547, 1641, 1478,  373,  22, },
+	{  33,  531, 1629, 1493,  386,  24, },
+	{  32,  516, 1617, 1508,  399,  24, },
+	{  31,  500, 1604, 1523,  413,  25, },
+	{  30,  485, 1592, 1537,  427,  25, },
+	{  29,  470, 1578, 1551,  441,  27, },
+	{  28,  455, 1565, 1565,  455,  28, },
+	{  27,  441, 1551, 1578,  470,  29, },
+	{  26,  427, 1537, 1592,  485,  29, },
+	{  25,  413, 1523, 1604,  500,  31, },
+	{  24,  399, 1508, 1617,  516,  32, },
+	{  24,  386, 1493, 1629,  531,  33, },
+	{  23,  373, 1478, 1641,  547,  34, },
+	{  22,  360, 1462, 1652,  563,  37, },
+	{  22,  347, 1446, 1663,  580,  38, },
+	{  21,  335, 1430, 1674,  596,  40, },
+	{  20,  323, 1414, 1684,  613,  42, },
+	{  20,  311, 1398, 1694,  630,  43, },
+	{  19,  299, 1381, 1704,  647,  46, },
+	{  19,  288, 1364, 1713,  664,  48, },
+	{  18,  277, 1347, 1722,  682,  50, },
+	{  17,  266, 1330, 1730,  699,  54, },
+	{  17,  256, 1313, 1738,  717,  55, },
+	{  16,  246, 1295, 1746,  735,  58, },
+	{  15,  236, 1277, 1753,  753,  62, },
+	{  15,  226, 1259, 1759,  772,  65, },
+	{  14,  217, 1241, 1766,  790,  68, },
+	{  13,  208, 1223, 1771,  809,  72, },
+	{  12,  199, 1205, 1777,  827,  76, },
+	{  11,  191, 1187, 1782,  846,  79, },
+	{  10,  182, 1168, 1786,  865,  85, },
+	{   9,  174, 1150, 1790,  884,  89, },
+	{   8,  167, 1131, 1794,  903,  93, },
+	{   7,  159, 1113, 1797,  922,  98, },
+	{   6,  152, 1094, 1800,  942, 102, },
+	{   5,  145, 1075, 1802,  961, 108, },
+	{   3,  138, 1057, 1804,  980, 114, },
+	{   2,  132, 1038, 1805, 1000, 119, }
+};
+
+/* ScalingRatio = 4 */
+static const s16 XV_fixedcoeff_taps6_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_6] = {
+	{ 176, 1009, 1643, 1009, 176,  83, },
+	{ 169,  993, 1644, 1026, 183,  81, },
+	{ 162,  978, 1644, 1042, 190,  80, },
+	{ 156,  962, 1643, 1058, 198,  79, },
+	{ 150,  946, 1642, 1074, 205,  79, },
+	{ 144,  930, 1641, 1091, 213,  77, },
+	{ 138,  914, 1640, 1107, 222,  75, },
+	{ 133,  898, 1638, 1123, 230,  74, },
+	{ 128,  882, 1635, 1139, 239,  73, },
+	{ 123,  866, 1633, 1154, 248,  72, },
+	{ 118,  850, 1629, 1170, 257,  72, },
+	{ 114,  834, 1626, 1186, 267,  69, },
+	{ 109,  818, 1622, 1201, 276,  70, },
+	{ 105,  802, 1618, 1217, 286,  68, },
+	{ 101,  786, 1613, 1232, 297,  67, },
+	{  97,  771, 1608, 1247, 307,  66, },
+	{  94,  755, 1603, 1262, 318,  64, },
+	{  91,  739, 1597, 1276, 328,  65, },
+	{  87,  724, 1591, 1291, 339,  64, },
+	{  85,  708, 1585, 1305, 351,  62, },
+	{  82,  693, 1578, 1319, 362,  62, },
+	{  79,  677, 1571, 1333, 374,  62, },
+	{  77,  662, 1563, 1347, 386,  61, },
+	{  75,  647, 1556, 1360, 398,  60, },
+	{  73,  632, 1547, 1373, 410,  61, },
+	{  71,  617, 1539, 1386, 423,  60, },
+	{  69,  602, 1530, 1399, 436,  60, },
+	{  68,  587, 1521, 1412, 449,  59, },
+	{  66,  573, 1511, 1424, 462,  60, },
+	{  65,  558, 1501, 1436, 475,  61, },
+	{  64,  544, 1491, 1447, 488,  62, },
+	{  63,  530, 1481, 1459, 502,  61, },
+	{  62,  516, 1470, 1470, 516,  62, },
+	{  62,  502, 1459, 1481, 530,  62, },
+	{  61,  488, 1447, 1491, 544,  65, },
+	{  61,  475, 1436, 1501, 558,  65, },
+	{  60,  462, 1424, 1511, 573,  66, },
+	{  60,  449, 1412, 1521, 587,  67, },
+	{  60,  436, 1399, 1530, 602,  69, },
+	{  60,  423, 1386, 1539, 617,  71, },
+	{  61,  410, 1373, 1547, 632,  73, },
+	{  61,  398, 1360, 1556, 647,  74, },
+	{  61,  386, 1347, 1563, 662,  77, },
+	{  62,  374, 1333, 1571, 677,  79, },
+	{  62,  362, 1319, 1578, 693,  82, },
+	{  63,  351, 1305, 1585, 708,  84, },
+	{  64,  339, 1291, 1591, 724,  87, },
+	{  64,  328, 1276, 1597, 739,  92, },
+	{  65,  318, 1262, 1603, 755,  93, },
+	{  66,  307, 1247, 1608, 771,  97, },
+	{  67,  297, 1232, 1613, 786, 101, },
+	{  68,  286, 1217, 1618, 802, 105, },
+	{  69,  276, 1201, 1622, 818, 110, },
+	{  70,  267, 1186, 1626, 834, 113, },
+	{  71,  257, 1170, 1629, 850, 119, },
+	{  72,  248, 1154, 1633, 866, 123, },
+	{  73,  239, 1139, 1635, 882, 128, },
+	{  75,  230, 1123, 1638, 898, 132, },
+	{  76,  222, 1107, 1640, 914, 137, },
+	{  77,  213, 1091, 1641, 930, 144, },
+	{  78,  205, 1074, 1642, 946, 151, },
+	{  79,  198, 1058, 1643, 962, 156, },
+	{  80,  190, 1042, 1644, 978, 162, },
+	{  82,  183, 1026, 1644, 993, 168, }
+};
+
+/* ScalingRatio = 2.0 */
+static const s16 XV_fixedcoeff_taps8_SR2[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_8] = {
+	{ -55,   0, 1078, 2049, 1078,    0, -55,   1, },
+	{ -53,  -7, 1055, 2049, 1102,    7, -56,  -1, },
+	{ -52, -13, 1032, 2048, 1126,   15, -58,  -2, },
+	{ -50, -20, 1009, 2047, 1149,   22, -59,  -2, },
+	{ -49, -26,  986, 2046, 1173,   31, -61,  -4, },
+	{ -47, -31,  963, 2043, 1197,   39, -62,  -6, },
+	{ -46, -37,  940, 2040, 1220,   48, -64,  -5, },
+	{ -45, -42,  917, 2037, 1244,   57, -65,  -7, },
+	{ -43, -47,  894, 2033, 1267,   66, -67,  -7, },
+	{ -42, -51,  871, 2028, 1290,   76, -69,  -7, },
+	{ -41, -55,  848, 2023, 1313,   86, -70,  -8, },
+	{ -40, -59,  826, 2017, 1336,   97, -72,  -9, },
+	{ -38, -63,  803, 2010, 1359,  108, -73, -10, },
+	{ -37, -67,  781, 2003, 1382,  119, -75, -10, },
+	{ -36, -70,  759, 1996, 1405,  130, -76, -12, },
+	{ -35, -73,  737, 1987, 1427,  142, -78, -11, },
+	{ -34, -76,  715, 1979, 1449,  154, -79, -12, },
+	{ -33, -78,  693, 1969, 1471,  167, -81, -12, },
+	{ -32, -81,  672, 1959, 1493,  180, -82, -13, },
+	{ -31, -83,  650, 1949, 1514,  193, -83, -13, },
+	{ -30, -85,  629, 1938, 1536,  207, -85, -14, },
+	{ -29, -86,  609, 1926, 1557,  221, -86, -16, },
+	{ -28, -88,  588, 1914, 1577,  235, -87, -15, },
+	{ -28, -89,  568, 1902, 1598,  250, -88, -17, },
+	{ -27, -90,  548, 1889, 1618,  265, -89, -18, },
+	{ -26, -91,  528, 1875, 1638,  280, -90, -18, },
+	{ -25, -92,  508, 1861, 1657,  296, -91, -18, },
+	{ -24, -93,  489, 1846, 1676,  312, -92, -18, },
+	{ -24, -93,  470, 1831, 1695,  328, -92, -19, },
+	{ -23, -94,  451, 1816, 1714,  345, -93, -20, },
+	{ -22, -94,  432, 1800, 1732,  361, -93, -20, },
+	{ -22, -94,  414, 1783, 1749,  379, -94, -19, },
+	{ -21, -94,  396, 1767, 1767,  396, -94, -21, },
+	{ -21, -94,  379, 1749, 1783,  414, -94, -20, },
+	{ -20, -93,  361, 1732, 1800,  432, -94, -22, },
+	{ -19, -93,  345, 1714, 1816,  451, -94, -24, },
+	{ -19, -92,  328, 1695, 1831,  470, -93, -24, },
+	{ -18, -92,  312, 1676, 1846,  489, -93, -24, },
+	{ -18, -91,  296, 1657, 1861,  508, -92, -25, },
+	{ -17, -90,  280, 1638, 1875,  528, -91, -27, },
+	{ -17, -89,  265, 1618, 1889,  548, -90, -28, },
+	{ -16, -88,  250, 1598, 1902,  568, -89, -29, },
+	{ -16, -87,  235, 1577, 1914,  588, -88, -27, },
+	{ -15, -86,  221, 1557, 1926,  609, -86, -30, },
+	{ -14, -85,  207, 1536, 1938,  629, -85, -30, },
+	{ -14, -83,  193, 1514, 1949,  650, -83, -30, },
+	{ -13, -82,  180, 1493, 1959,  672, -81, -32, },
+	{ -13, -81,  167, 1471, 1969,  693, -78, -32, },
+	{ -12, -79,  154, 1449, 1979,  715, -76, -34, },
+	{ -12, -78,  142, 1427, 1987,  737, -73, -34, },
+	{ -11, -76,  130, 1405, 1996,  759, -70, -37, },
+	{ -10, -75,  119, 1382, 2003,  781, -67, -37, },
+	{ -10, -73,  108, 1359, 2010,  803, -63, -38, },
+	{  -9, -72,   97, 1336, 2017,  826, -59, -40, },
+	{  -8, -70,   86, 1313, 2023,  848, -55, -41, },
+	{  -8, -69,   76, 1290, 2028,  871, -51, -41, },
+	{  -7, -67,   66, 1267, 2033,  894, -47, -43, },
+	{  -6, -65,   57, 1244, 2037,  917, -42, -46, },
+	{  -5, -64,   48, 1220, 2040,  940, -37, -46, },
+	{  -5, -62,   39, 1197, 2043,  963, -31, -48, },
+	{  -4, -61,   31, 1173, 2046,  986, -26, -49, },
+	{  -3, -59,   22, 1149, 2047, 1009, -20, -49, },
+	{  -2, -58,   15, 1126, 2048, 1032, -13, -52, },
+	{  -1, -56,    7, 1102, 2049, 1055,  -7, -53, }
+};
+
+/* ScalingRatio = 3.0 */
+static const s16 XV_fixedcoeff_taps8_SR3[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_8] = {
+	{   0, 275, 1036, 1514, 1036,  275,   0, -40, },
+	{  -1, 266, 1023, 1514, 1048,  283,   1, -38, },
+	{  -2, 257, 1010, 1513, 1060,  292,   2, -36, },
+	{  -3, 249,  997, 1512, 1073,  301,   3, -36, },
+	{  -3, 241,  983, 1510, 1085,  310,   5, -35, },
+	{  -4, 233,  970, 1509, 1097,  319,   6, -34, },
+	{  -5, 225,  957, 1507, 1109,  329,   7, -33, },
+	{  -6, 217,  944, 1505, 1121,  338,   9, -32, },
+	{  -6, 210,  931, 1503, 1133,  348,  10, -33, },
+	{  -7, 202,  917, 1500, 1144,  358,  12, -30, },
+	{  -7, 195,  904, 1497, 1156,  368,  13, -30, },
+	{  -8, 188,  891, 1494, 1167,  378,  15, -29, },
+	{  -9, 181,  877, 1491, 1179,  388,  17, -28, },
+	{  -9, 174,  864, 1487, 1190,  398,  19, -27, },
+	{  -9, 168,  851, 1483, 1201,  409,  21, -28, },
+	{ -10, 161,  837, 1479, 1212,  419,  23, -25, },
+	{ -10, 155,  824, 1475, 1223,  430,  25, -26, },
+	{ -11, 149,  811, 1470, 1233,  441,  27, -24, },
+	{ -11, 142,  798, 1465, 1244,  452,  29, -23, },
+	{ -12, 137,  784, 1460, 1254,  463,  32, -22, },
+	{ -12, 131,  771, 1455, 1264,  474,  34, -21, },
+	{ -12, 125,  758, 1449, 1275,  486,  37, -22, },
+	{ -13, 120,  745, 1444, 1284,  497,  40, -21, },
+	{ -13, 115,  732, 1438, 1294,  509,  42, -21, },
+	{ -13, 109,  719, 1432, 1304,  520,  45, -20, },
+	{ -14, 104,  706, 1425, 1313,  532,  48, -18, },
+	{ -14, 100,  693, 1418, 1322,  544,  52, -19, },
+	{ -14,  95,  680, 1412, 1332,  556,  55, -20, },
+	{ -15,  90,  667, 1404, 1340,  568,  58, -16, },
+	{ -15,  86,  655, 1397, 1349,  580,  62, -18, },
+	{ -16,  82,  642, 1390, 1358,  592,  66, -18, },
+	{ -16,  77,  630, 1382, 1366,  605,  69, -17, },
+	{ -16,  73,  617, 1374, 1374,  617,  73, -16, },
+	{ -17,  69,  605, 1366, 1382,  630,  77, -16, },
+	{ -17,  66,  592, 1358, 1390,  642,  82, -17, },
+	{ -18,  62,  580, 1349, 1397,  655,  86, -15, },
+	{ -18,  58,  568, 1340, 1404,  667,  90, -13, },
+	{ -18,  55,  556, 1332, 1412,  680,  95, -16, },
+	{ -19,  52,  544, 1322, 1418,  693, 100, -14, },
+	{ -19,  48,  532, 1313, 1425,  706, 104, -13, },
+	{ -20,  45,  520, 1304, 1432,  719, 109, -13, },
+	{ -20,  42,  509, 1294, 1438,  732, 115, -14, },
+	{ -21,  40,  497, 1284, 1444,  745, 120, -13, },
+	{ -22,  37,  486, 1275, 1449,  758, 125, -12, },
+	{ -22,  34,  474, 1264, 1455,  771, 131, -11, },
+	{ -23,  32,  463, 1254, 1460,  784, 137, -11, },
+	{ -23,  29,  452, 1244, 1465,  798, 142, -11, },
+	{ -24,  27,  441, 1233, 1470,  811, 149, -11, },
+	{ -25,  25,  430, 1223, 1475,  824, 155, -11, },
+	{ -26,  23,  419, 1212, 1479,  837, 161,  -9, },
+	{ -26,  21,  409, 1201, 1483,  851, 168, -11, },
+	{ -27,  19,  398, 1190, 1487,  864, 174,  -9, },
+	{ -28,  17,  388, 1179, 1491,  877, 181,  -9, },
+	{ -29,  15,  378, 1167, 1494,  891, 188,  -8, },
+	{ -29,  13,  368, 1156, 1497,  904, 195,  -8, },
+	{ -30,  12,  358, 1144, 1500,  917, 202,  -7, },
+	{ -31,  10,  348, 1133, 1503,  931, 210,  -8, },
+	{ -32,   9,  338, 1121, 1505,  944, 217,  -6, },
+	{ -33,   7,  329, 1109, 1507,  957, 225,  -5, },
+	{ -34,   6,  319, 1097, 1509,  970, 233,  -4, },
+	{ -35,   5,  310, 1085, 1510,  983, 241,  -3, },
+	{ -36,   3,  301, 1073, 1512,  997, 249,  -3, },
+	{ -37,   2,  292, 1060, 1513, 1010, 257,  -1, },
+	{ -38,   1,  283, 1048, 1514, 1023, 266,  -1, }
+};
+
+/* ScalingRatio = 4 */
+static const s16 XV_fixedcoeff_taps8_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_8] = {
+	{ 49, 366, 977, 1312,  977, 366,  49,  0, },
+	{ 48, 357, 967, 1312,  986, 374,  51,  1, },
+	{ 46, 349, 958, 1311,  995, 382,  54,  1, },
+	{ 44, 342, 948, 1311, 1004, 390,  56,  1, },
+	{ 42, 334, 939, 1310, 1013, 399,  58,  1, },
+	{ 40, 326, 929, 1309, 1021, 407,  60,  4, },
+	{ 39, 318, 919, 1308, 1030, 415,  63,  4, },
+	{ 37, 311, 910, 1307, 1039, 424,  65,  3, },
+	{ 36, 303, 900, 1305, 1047, 433,  68,  4, },
+	{ 34, 296, 890, 1303, 1055, 442,  70,  6, },
+	{ 33, 289, 880, 1301, 1064, 450,  73,  6, },
+	{ 32, 282, 870, 1299, 1072, 459,  76,  6, },
+	{ 31, 275, 861, 1297, 1080, 468,  79,  5, },
+	{ 29, 268, 851, 1295, 1088, 477,  82,  6, },
+	{ 28, 261, 841, 1292, 1096, 486,  85,  7, },
+	{ 27, 254, 831, 1289, 1104, 496,  88,  7, },
+	{ 26, 248, 821, 1287, 1112, 505,  91,  6, },
+	{ 25, 241, 811, 1284, 1119, 514,  94,  8, },
+	{ 24, 235, 800, 1280, 1127, 523,  98,  9, },
+	{ 23, 228, 790, 1277, 1134, 533, 101, 10, },
+	{ 22, 222, 780, 1273, 1141, 542, 105, 11, },
+	{ 22, 216, 770, 1270, 1148, 552, 109,  9, },
+	{ 21, 210, 760, 1266, 1155, 561, 112, 11, },
+	{ 20, 204, 750, 1262, 1162, 571, 116, 11, },
+	{ 19, 198, 740, 1257, 1169, 581, 120, 12, },
+	{ 19, 193, 730, 1253, 1175, 590, 124, 12, },
+	{ 18, 187, 720, 1248, 1182, 600, 129, 12, },
+	{ 17, 182, 710, 1244, 1188, 610, 133, 12, },
+	{ 17, 176, 700, 1239, 1194, 620, 137, 13, },
+	{ 16, 171, 690, 1234, 1201, 630, 142, 12, },
+	{ 16, 166, 680, 1229, 1206, 640, 146, 13, },
+	{ 15, 161, 670, 1223, 1212, 650, 151, 14, },
+	{ 15, 156, 660, 1218, 1218, 660, 156, 13, },
+	{ 14, 151, 650, 1212, 1223, 670, 161, 15, },
+	{ 14, 146, 640, 1206, 1229, 680, 166, 15, },
+	{ 13, 142, 630, 1201, 1234, 690, 171, 15, },
+	{ 13, 137, 620, 1194, 1239, 700, 176, 17, },
+	{ 12, 133, 610, 1188, 1244, 710, 182, 17, },
+	{ 12, 129, 600, 1182, 1248, 720, 187, 18, },
+	{ 11, 124, 590, 1175, 1253, 730, 193, 20, },
+	{ 11, 120, 581, 1169, 1257, 740, 198, 20, },
+	{ 11, 116, 571, 1162, 1262, 750, 204, 20, },
+	{ 10, 112, 561, 1155, 1266, 760, 210, 22, },
+	{ 10, 109, 552, 1148, 1270, 770, 216, 21, },
+	{ 10, 105, 542, 1141, 1273, 780, 222, 23, },
+	{  9, 101, 533, 1134, 1277, 790, 228, 24, },
+	{  9,  98, 523, 1127, 1280, 800, 235, 24, },
+	{  8,  94, 514, 1119, 1284, 811, 241, 25, },
+	{  8,  91, 505, 1112, 1287, 821, 248, 24, },
+	{  8,  88, 496, 1104, 1289, 831, 254, 26, },
+	{  7,  85, 486, 1096, 1292, 841, 261, 28, },
+	{  7,  82, 477, 1088, 1295, 851, 268, 28, },
+	{  6,  79, 468, 1080, 1297, 861, 275, 30, },
+	{  6,  76, 459, 1072, 1299, 870, 282, 32, },
+	{  5,  73, 450, 1064, 1301, 880, 289, 34, },
+	{  5,  70, 442, 1055, 1303, 890, 296, 35, },
+	{  4,  68, 433, 1047, 1305, 900, 303, 36, },
+	{  4,  65, 424, 1039, 1307, 910, 311, 36, },
+	{  3,  63, 415, 1030, 1308, 919, 318, 40, },
+	{  3,  60, 407, 1021, 1309, 929, 326, 41, },
+	{  2,  58, 399, 1013, 1310, 939, 334, 41, },
+	{  2,  56, 390, 1004, 1311, 948, 342, 43, },
+	{  1,  54, 382,  995, 1311, 958, 349, 46, },
+	{  1,  51, 374,  986, 1312, 967, 357, 48, }
+};
+
+/* ScalingRatio = 3.0 */
+static const s16 XV_fixedcoeff_taps10_SR3[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_10] = {
+	{ -31,   0, 359, 1033, 1399, 1033,  359,   0, -31, -25, },
+	{ -31,  -2, 350, 1022, 1398, 1043,  368,   3, -31, -24, },
+	{ -30,  -4, 341, 1012, 1398, 1053,  378,   5, -32, -25, },
+	{ -30,  -6, 333, 1002, 1398, 1062,  387,   8, -32, -26, },
+	{ -30,  -8, 324,  992, 1397, 1072,  396,  10, -32, -25, },
+	{ -30, -10, 315,  981, 1396, 1082,  406,  13, -33, -24, },
+	{ -29, -12, 307,  971, 1395, 1091,  415,  16, -33, -25, },
+	{ -29, -13, 298,  960, 1393, 1101,  425,  18, -33, -24, },
+	{ -29, -15, 290,  949, 1392, 1110,  434,  21, -34, -22, },
+	{ -28, -17, 282,  939, 1390, 1120,  444,  25, -34, -25, },
+	{ -28, -18, 274,  928, 1388, 1129,  454,  28, -34, -25, },
+	{ -28, -20, 266,  917, 1386, 1138,  464,  31, -34, -24, },
+	{ -27, -21, 258,  906, 1384, 1147,  474,  34, -35, -24, },
+	{ -27, -22, 250,  895, 1381, 1156,  484,  38, -35, -24, },
+	{ -27, -23, 242,  885, 1379, 1164,  494,  41, -35, -24, },
+	{ -27, -25, 235,  874, 1376, 1173,  504,  45, -35, -24, },
+	{ -26, -26, 227,  863, 1373, 1181,  515,  49, -36, -24, },
+	{ -26, -27, 220,  852, 1369, 1190,  525,  53, -36, -24, },
+	{ -26, -28, 213,  841, 1366, 1198,  535,  56, -36, -23, },
+	{ -26, -29, 206,  830, 1362, 1206,  546,  61, -36, -24, },
+	{ -25, -29, 199,  819, 1358, 1214,  556,  65, -36, -25, },
+	{ -25, -30, 192,  808, 1354, 1222,  567,  69, -36, -25, },
+	{ -25, -31, 185,  797, 1350, 1229,  577,  73, -36, -23, },
+	{ -25, -32, 178,  785, 1346, 1237,  588,  78, -36, -23, },
+	{ -25, -32, 172,  774, 1341, 1244,  599,  83, -36, -24, },
+	{ -25, -33, 165,  763, 1336, 1252,  610,  87, -36, -23, },
+	{ -24, -33, 159,  752, 1331, 1259,  620,  92, -36, -24, },
+	{ -24, -34, 153,  741, 1326, 1266,  631,  97, -36, -24, },
+	{ -24, -34, 147,  730, 1321, 1272,  642, 102, -36, -24, },
+	{ -24, -35, 141,  719, 1315, 1279,  653, 107, -36, -23, },
+	{ -24, -35, 135,  708, 1310, 1285,  664, 113, -36, -24, },
+	{ -24, -35, 129,  697, 1304, 1292,  675, 118, -36, -24, },
+	{ -24, -36, 124,  686, 1298, 1298,  686, 124, -36, -24, },
+	{ -24, -36, 118,  675, 1292, 1304,  697, 129, -35, -24, },
+	{ -24, -36, 113,  664, 1285, 1310,  708, 135, -35, -24, },
+	{ -24, -36, 107,  653, 1279, 1315,  719, 141, -35, -23, },
+	{ -24, -36, 102,  642, 1272, 1321,  730, 147, -34, -24, },
+	{ -23, -36,  97,  631, 1266, 1326,  741, 153, -34, -25, },
+	{ -23, -36,  92,  620, 1259, 1331,  752, 159, -33, -25, },
+	{ -23, -36,  87,  610, 1252, 1336,  763, 165, -33, -25, },
+	{ -23, -36,  83,  599, 1244, 1341,  774, 172, -32, -26, },
+	{ -23, -36,  78,  588, 1237, 1346,  785, 178, -32, -25, },
+	{ -23, -36,  73,  577, 1229, 1350,  797, 185, -31, -25, },
+	{ -23, -36,  69,  567, 1222, 1354,  808, 192, -30, -27, },
+	{ -23, -36,  65,  556, 1214, 1358,  819, 199, -29, -27, },
+	{ -24, -36,  61,  546, 1206, 1362,  830, 206, -29, -26, },
+	{ -24, -36,  56,  535, 1198, 1366,  841, 213, -28, -25, },
+	{ -24, -36,  53,  525, 1190, 1369,  852, 220, -27, -26, },
+	{ -24, -36,  49,  515, 1181, 1373,  863, 227, -26, -26, },
+	{ -24, -35,  45,  504, 1173, 1376,  874, 235, -25, -27, },
+	{ -24, -35,  41,  494, 1164, 1379,  885, 242, -23, -27, },
+	{ -24, -35,  38,  484, 1156, 1381,  895, 250, -22, -27, },
+	{ -24, -35,  34,  474, 1147, 1384,  906, 258, -21, -27, },
+	{ -24, -34,  31,  464, 1138, 1386,  917, 266, -20, -28, },
+	{ -24, -34,  28,  454, 1129, 1388,  928, 274, -18, -29, },
+	{ -24, -34,  25,  444, 1120, 1390,  939, 282, -17, -29, },
+	{ -24, -34,  21,  434, 1110, 1392,  949, 290, -15, -27, },
+	{ -24, -33,  18,  425, 1101, 1393,  960, 298, -13, -29, },
+	{ -24, -33,  16,  415, 1091, 1395,  971, 307, -12, -30, },
+	{ -25, -33,  13,  406, 1082, 1396,  981, 315, -10, -29, },
+	{ -25, -32,  10,  396, 1072, 1397,  992, 324,  -8, -30, },
+	{ -25, -32,   8,  387, 1062, 1398, 1002, 333,  -6, -31, },
+	{ -25, -32,   5,  378, 1053, 1398, 1012, 341,  -4, -30, },
+	{ -25, -31,   3,  368, 1043, 1398, 1022, 350,  -2, -30, }
+};
+
+/* ScalingRatio = 4 */
+static const s16 XV_fixedcoeff_taps10_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_10] = {
+	{   0, 107, 454, 924, 1150,  924, 454, 107,   0, -24, },
+	{   0, 104, 446, 917, 1149,  930, 461, 110,   0, -21, },
+	{  -1, 100, 439, 910, 1149,  936, 468, 114,   1, -20, },
+	{  -1,  97, 432, 904, 1149,  942, 475, 117,   2, -21, },
+	{  -2,  94, 425, 897, 1148,  948, 482, 121,   2, -19, },
+	{  -2,  91, 418, 890, 1147,  954, 490, 125,   3, -20, },
+	{  -3,  88, 411, 883, 1147,  960, 497, 128,   3, -18, },
+	{  -3,  85, 404, 876, 1146,  966, 504, 132,   4, -18, },
+	{  -3,  82, 397, 869, 1145,  972, 512, 136,   5, -19, },
+	{  -4,  79, 390, 862, 1144,  978, 519, 140,   5, -17, },
+	{  -4,  76, 384, 855, 1142,  983, 526, 144,   6, -16, },
+	{  -4,  74, 377, 848, 1141,  989, 534, 148,   7, -18, },
+	{  -5,  71, 370, 841, 1139,  995, 541, 152,   7, -15, },
+	{  -5,  68, 364, 834, 1138, 1000, 549, 156,   8, -16, },
+	{  -5,  66, 357, 827, 1136, 1005, 556, 160,   9, -15, },
+	{  -6,  63, 350, 820, 1134, 1011, 564, 165,  10, -15, },
+	{  -6,  61, 344, 812, 1132, 1016, 571, 169,  11, -14, },
+	{  -6,  59, 338, 805, 1130, 1021, 579, 174,  12, -16, },
+	{  -6,  56, 331, 798, 1128, 1026, 586, 178,  13, -14, },
+	{  -7,  54, 325, 790, 1126, 1031, 594, 183,  14, -14, },
+	{  -7,  52, 319, 783, 1124, 1036, 601, 187,  15, -14, },
+	{  -7,  50, 312, 776, 1121, 1041, 609, 192,  16, -14, },
+	{  -7,  48, 306, 768, 1119, 1045, 617, 197,  17, -14, },
+	{  -8,  46, 300, 761, 1116, 1050, 624, 202,  18, -13, },
+	{  -8,  44, 294, 753, 1113, 1054, 632, 207,  19, -12, },
+	{  -8,  42, 288, 746, 1110, 1059, 639, 212,  20, -12, },
+	{  -8,  40, 282, 738, 1107, 1063, 647, 217,  22, -12, },
+	{  -9,  38, 277, 731, 1104, 1067, 655, 222,  23, -12, },
+	{  -9,  36, 271, 723, 1101, 1071, 662, 227,  24, -10, },
+	{  -9,  35, 265, 715, 1097, 1075, 670, 232,  26, -10, },
+	{  -9,  33, 259, 708, 1094, 1079, 677, 238,  27, -10, },
+	{ -10,  32, 254, 700, 1091, 1083, 685, 243,  28, -10, },
+	{ -10,  30, 248, 693, 1087, 1087, 693, 248,  30, -10, },
+	{ -10,  28, 243, 685, 1083, 1091, 700, 254,  32, -10, },
+	{ -10,  27, 238, 677, 1079, 1094, 708, 259,  33,  -9, },
+	{ -11,  26, 232, 670, 1075, 1097, 715, 265,  35,  -8, },
+	{ -11,  24, 227, 662, 1071, 1101, 723, 271,  36,  -8, },
+	{ -11,  23, 222, 655, 1067, 1104, 731, 277,  38, -10, },
+	{ -12,  22, 217, 647, 1063, 1107, 738, 282,  40,  -8, },
+	{ -12,  20, 212, 639, 1059, 1110, 746, 288,  42,  -8, },
+	{ -12,  19, 207, 632, 1054, 1113, 753, 294,  44,  -8, },
+	{ -12,  18, 202, 624, 1050, 1116, 761, 300,  46,  -9, },
+	{ -13,  17, 197, 617, 1045, 1119, 768, 306,  48,  -8, },
+	{ -13,  16, 192, 609, 1041, 1121, 776, 312,  50,  -8, },
+	{ -13,  15, 187, 601, 1036, 1124, 783, 319,  52,  -8, },
+	{ -14,  14, 183, 594, 1031, 1126, 790, 325,  54,  -7, },
+	{ -14,  13, 178, 586, 1026, 1128, 798, 331,  56,  -6, },
+	{ -14,  12, 174, 579, 1021, 1130, 805, 338,  59,  -8, },
+	{ -15,  11, 169, 571, 1016, 1132, 812, 344,  61,  -5, },
+	{ -15,  10, 165, 564, 1011, 1134, 820, 350,  63,  -6, },
+	{ -16,   9, 160, 556, 1005, 1136, 827, 357,  66,  -4, },
+	{ -16,   8, 156, 549, 1000, 1138, 834, 364,  68,  -5, },
+	{ -16,   7, 152, 541,  995, 1139, 841, 370,  71,  -4, },
+	{ -17,   7, 148, 534,  989, 1141, 848, 377,  74,  -5, },
+	{ -17,   6, 144, 526,  983, 1142, 855, 384,  76,  -3, },
+	{ -18,   5, 140, 519,  978, 1144, 862, 390,  79,  -3, },
+	{ -18,   5, 136, 512,  972, 1145, 869, 397,  82,  -4, },
+	{ -19,   4, 132, 504,  966, 1146, 876, 404,  85,  -2, },
+	{ -19,   3, 128, 497,  960, 1147, 883, 411,  88,  -2, },
+	{ -20,   3, 125, 490,  954, 1147, 890, 418,  91,  -2, },
+	{ -20,   2, 121, 482,  948, 1148, 897, 425,  94,  -1, },
+	{ -21,   2, 117, 475,  942, 1149, 904, 432,  97,  -1, },
+	{ -21,   1, 114, 468,  936, 1149, 910, 439, 100,   0, },
+	{ -22,   0, 110, 461,  930, 1149, 917, 446, 104,   1, }
+};
+
+/* ScalingRatio = 4 */
+static const s16 XV_fixedcoeff_taps12_SR4[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_TAPS_12] = {
+	{ -19,   0, 152, 498, 893, 1070,  893, 498, 152,   0, -19, -22, },
+	{ -19,  -1, 147, 487, 879, 1059,  889, 499, 155,   1, -19,  19, },
+	{ -19,  -2, 143, 480, 874, 1059,  894, 506, 159,   2, -19,  19, },
+	{ -19,  -3, 139, 474, 869, 1059,  899, 512, 163,   3, -19,  19, },
+	{ -19,  -4, 136, 468, 863, 1059,  904, 519, 167,   4, -19,  18, },
+	{ -19,  -5, 132, 461, 858, 1058,  909, 525, 171,   5, -19,  20, },
+	{ -19,  -5, 128, 455, 853, 1058,  913, 531, 175,   7, -19,  19, },
+	{ -18,  -6, 125, 449, 847, 1057,  918, 538, 180,   8, -19,  17, },
+	{ -18,  -7, 121, 443, 842, 1056,  923, 544, 184,   9, -19,  18, },
+	{ -18,  -8, 118, 436, 836, 1056,  927, 551, 188,  10, -19,  19, },
+	{ -18,  -8, 114, 430, 831, 1055,  932, 557, 193,  12, -19,  17, },
+	{ -18,  -9, 111, 424, 825, 1054,  936, 564, 197,  13, -19,  18, },
+	{ -18, -10, 107, 418, 819, 1053,  941, 570, 202,  14, -19,  19, },
+	{ -18, -10, 104, 412, 814, 1052,  945, 577, 206,  16, -19,  17, },
+	{ -18, -11, 101, 406, 808, 1050,  949, 583, 211,  17, -19,  19, },
+	{ -18, -11,  98, 400, 802, 1049,  954, 590, 216,  19, -19,  16, },
+	{ -18, -12,  95, 394, 796, 1048,  958, 596, 220,  20, -19,  18, },
+	{ -18, -12,  92, 388, 791, 1046,  962, 603, 225,  22, -19,  16, },
+	{ -18, -13,  89, 382, 785, 1045,  966, 609, 230,  24, -19,  16, },
+	{ -18, -13,  86, 376, 779, 1043,  970, 616, 235,  25, -19,  16, },
+	{ -18, -14,  83, 370, 773, 1041,  973, 622, 240,  27, -19,  18, },
+	{ -18, -14,  80, 364, 767, 1039,  977, 629, 244,  29, -19,  18, },
+	{ -18, -15,  77, 358, 761, 1037,  981, 635, 249,  31, -19,  19, },
+	{ -18, -15,  74, 352, 755, 1035,  984, 642, 255,  33, -19,  18, },
+	{ -18, -15,  71, 347, 749, 1033,  988, 648, 260,  35, -19,  17, },
+	{ -18, -16,  69, 341, 743, 1031,  991, 654, 265,  36, -19,  19, },
+	{ -18, -16,  66, 335, 736, 1029,  995, 661, 270,  38, -19,  19, },
+	{ -18, -16,  64, 330, 730, 1026,  998, 667, 275,  41, -18,  17, },
+	{ -18, -17,  61, 324, 724, 1024, 1001, 674, 280,  43, -18,  18, },
+	{ -18, -17,  59, 318, 718, 1021, 1004, 680, 286,  45, -18,  18, },
+	{ -18, -17,  56, 313, 712, 1019, 1007, 686, 291,  47, -18,  18, },
+	{ -18, -17,  54, 307, 705, 1016, 1010, 693, 296,  49, -18,  19, },
+	{ -18, -18,  51, 302, 699, 1013, 1013, 699, 302,  51, -18,  20, },
+	{ -18, -18,  49, 296, 693, 1010, 1016, 705, 307,  54, -17,  19, },
+	{ -18, -18,  47, 291, 686, 1007, 1019, 712, 313,  56, -17,  18, },
+	{ -18, -18,  45, 286, 680, 1004, 1021, 718, 318,  59, -17,  18, },
+	{ -18, -18,  43, 280, 674, 1001, 1024, 724, 324,  61, -17,  18, },
+	{ -18, -18,  41, 275, 667,  998, 1026, 730, 330,  64, -16,  17, },
+	{ -18, -19,  38, 270, 661,  995, 1029, 736, 335,  66, -16,  19, },
+	{ -19, -19,  36, 265, 654,  991, 1031, 743, 341,  69, -16,  20, },
+	{ -19, -19,  35, 260, 648,  988, 1033, 749, 347,  71, -15,  18, },
+	{ -19, -19,  33, 255, 642,  984, 1035, 755, 352,  74, -15,  19, },
+	{ -19, -19,  31, 249, 635,  981, 1037, 761, 358,  77, -15,  20, },
+	{ -19, -19,  29, 244, 629,  977, 1039, 767, 364,  80, -14,  19, },
+	{ -19, -19,  27, 240, 622,  973, 1041, 773, 370,  83, -14,  19, },
+	{ -19, -19,  25, 235, 616,  970, 1043, 779, 376,  86, -13,  17, },
+	{ -19, -19,  24, 230, 609,  966, 1045, 785, 382,  89, -13,  17, },
+	{ -19, -19,  22, 225, 603,  962, 1046, 791, 388,  92, -12,  17, },
+	{ -19, -19,  20, 220, 596,  958, 1048, 796, 394,  95, -12,  19, },
+	{ -20, -19,  19, 216, 590,  954, 1049, 802, 400,  98, -11,  18, },
+	{ -20, -19,  17, 211, 583,  949, 1050, 808, 406, 101, -11,  21, },
+	{ -20, -19,  16, 206, 577,  945, 1052, 814, 412, 104, -10,  19, },
+	{ -20, -19,  14, 202, 570,  941, 1053, 819, 418, 107, -10,  21, },
+	{ -20, -19,  13, 197, 564,  936, 1054, 825, 424, 111,  -9,  20, },
+	{ -20, -19,  12, 193, 557,  932, 1055, 831, 430, 114,  -8,  19, },
+	{ -21, -19,  10, 188, 551,  927, 1056, 836, 436, 118,  -8,  22, },
+	{ -21, -19,   9, 184, 544,  923, 1056, 842, 443, 121,  -7,  21, },
+	{ -21, -19,   8, 180, 538,  918, 1057, 847, 449, 125,  -6,  20, },
+	{ -21, -19,   7, 175, 531,  913, 1058, 853, 455, 128,  -5,  21, },
+	{ -21, -19,   5, 171, 525,  909, 1058, 858, 461, 132,  -5,  22, },
+	{ -21, -19,   4, 167, 519,  904, 1059, 863, 468, 136,  -4,  20, },
+	{ -22, -19,   3, 163, 512,  899, 1059, 869, 474, 139,  -3,  22, },
+	{ -22, -19,   2, 159, 506,  894, 1059, 874, 480, 143,  -2,  22, },
+	{ -22, -19,   1, 155, 499,  889, 1059, 879, 487, 147,  -1,  22, }
+};
+
+#define XV_HSCALER_CTRL_WIDTH_HWREG_HFLTCOEFF			(16)
+#define XV_HSCALER_CTRL_DEPTH_HWREG_HFLTCOEFF			(384)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PHASESH_V_BASE		(0x2000)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PHASESH_V_HIGH		(0x3fff)
+#define XV_HSCALER_CTRL_WIDTH_HWREG_PHASESH_V			(18)
+#define XV_HSCALER_CTRL_DEPTH_HWREG_PHASESH_V			(1920)
+#define XV_HSCALER_CTRL_ADDR_HWREG_PHASEH_FIX			(0x4000)
+
+/* H-scaler masks */
+#define XV_HSCALER_PHASESH_V_OUTPUT_WR_EN			BIT(8)
+
+/* V-scaler registers */
+#define XV_VSCALER_CTRL_ADDR_AP_CTRL			(0x000)
+#define XV_VSCALER_CTRL_ADDR_GIE			(0x004)
+#define XV_VSCALER_CTRL_ADDR_IER			(0x008)
+#define XV_VSCALER_CTRL_ADDR_ISR			(0x00c)
+#define XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTIN_DATA	(0x010)
+#define XV_VSCALER_CTRL_ADDR_HWREG_WIDTH_DATA		(0x018)
+#define XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTOUT_DATA	(0x020)
+#define XV_VSCALER_CTRL_ADDR_HWREG_LINERATE_DATA	(0x028)
+#define XV_VSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA	(0x030)
+#define XV_VSCALER_CTRL_ADDR_HWREG_VFLTCOEFF_BASE	(0x800)
+#define XV_VSCALER_CTRL_ADDR_HWREG_VFLTCOEFF_HIGH	(0xbff)
+
+#define XV_VSCALER_CTRL_WIDTH_HWREG_VFLTCOEFF		(16)
+#define XV_VSCALER_CTRL_DEPTH_HWREG_VFLTCOEFF		(384)
+
+/* These bits are for xscaler feature flags */
+#define XSCALER_CLK_PROP	BIT(0)
+#define XSCALER_HPHASE_FIX	BIT(1)
+
+/**
+ * struct xscaler_feature - dt or IP property structure
+ * @flags: Bitmask of properties enabled in IP or dt
+ */
+struct xscaler_feature {
+	u32 flags;
+};
+
+/**
+ * struct xscaler_device - Xilinx Scaler device structure
+ * @xvip: Xilinx Video IP device
+ * @pads: Scaler sub-device media pads
+ * @formats: V4L2 media bus formats at the sink and source pads
+ * @default_formats: default V4L2 media bus formats
+ * @vip_formats: Xilinx Video IP format retrieved from the DT
+ * @num_hori_taps: number of horizontal taps
+ * @num_vert_taps: number of vertical taps
+ * @max_num_phases: maximum number of phases
+ * @pix_per_clk: Pixels per Clock cycle the IP operates upon
+ * @max_pixels: The maximum number of pixels that the H-scaler examines
+ * @max_lines: The maximum number of lines that the V-scaler examines
+ * @H_phases: The phases needed to program the H-scaler for different taps
+ * @hscaler_coeff: The complete array of H-scaler coefficients
+ * @vscaler_coeff: The complete array of V-scaler coefficients
+ * @is_polyphase: Track if scaling algorithm is polyphase or not
+ * @rst_gpio: GPIO reset line to bring VPSS Scaler out of reset
+ * @cfg: Pointer to scaler config structure
+ * @aclk_axis: AXI4-Stream video interface clock
+ * @aclk_ctrl: AXI4-Lite control interface clock
+ */
+struct xscaler_device {
+	struct xvip_device xvip;
+
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+	const struct xvip_video_format *vip_formats[2];
+
+	u32 num_hori_taps;
+	u32 num_vert_taps;
+	u32 max_num_phases;
+	u32 pix_per_clk;
+	u32 max_pixels;
+	u32 max_lines;
+	u64 H_phases[XV_HSCALER_MAX_LINE_WIDTH];
+	short hscaler_coeff[XV_HSCALER_MAX_H_PHASES][XV_HSCALER_MAX_H_TAPS];
+	short vscaler_coeff[XV_VSCALER_MAX_V_PHASES][XV_VSCALER_MAX_V_TAPS];
+	bool is_polyphase;
+
+	struct gpio_desc *rst_gpio;
+	const struct xscaler_feature *cfg;
+	struct clk *aclk_axis;
+	struct clk *aclk_ctrl;
+};
+
+static const struct xscaler_feature xlnx_scaler_v2_2 = {
+	.flags = XSCALER_CLK_PROP | XSCALER_HPHASE_FIX,
+};
+
+static const struct xscaler_feature xlnx_scaler_v1_0 = {
+	.flags = XSCALER_CLK_PROP,
+};
+
+static const struct xscaler_feature xlnx_scaler = {
+	.flags = 0,
+};
+
+static const struct of_device_id xscaler_of_id_table[] = {
+	{ .compatible = "xlnx,v-vpss-scaler",
+		.data = &xlnx_scaler},
+	{ .compatible = "xlnx,v-vpss-scaler-1.0",
+		.data = &xlnx_scaler_v1_0},
+	{ .compatible = "xlnx,v-vpss-scaler-2.2",
+		.data = &xlnx_scaler_v2_2},
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xscaler_of_id_table);
+
+static inline struct xscaler_device *to_scaler(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xscaler_device, xvip.subdev);
+}
+
+static void
+xv_hscaler_calculate_phases(struct xscaler_device *xscaler,
+			    u32 width_in, u32 width_out, u32 pixel_rate)
+{
+	unsigned int loop_width;
+	unsigned int x, s;
+	int offset = 0;
+	int xwrite_pos = 0;
+	bool output_write_en;
+	bool get_new_pix;
+	u64 phaseH;
+	u64 array_idx = 0;
+	int nr_rds = 0;
+	int nr_rds_clck;
+	unsigned int nphases = xscaler->max_num_phases;
+	unsigned int nppc = xscaler->pix_per_clk;
+	unsigned int shift = XHSC_STEP_PRECISION_SHIFT - ilog2(nphases);
+
+	loop_width = max_t(u32, width_in, width_out);
+	loop_width = ALIGN(loop_width + nppc - 1, nppc);
+
+	for (x = 0; x < loop_width; x++) {
+		nr_rds_clck = 0;
+		for (s = 0; s < nppc; s++) {
+			phaseH = (offset >> shift) & (nphases - 1);
+			get_new_pix = false;
+			output_write_en = false;
+			if ((offset >> XHSC_STEP_PRECISION_SHIFT) != 0) {
+				/* read a new input sample */
+				get_new_pix = true;
+				offset -= (1 << XHSC_STEP_PRECISION_SHIFT);
+				array_idx++;
+			}
+
+			if (((offset >> XHSC_STEP_PRECISION_SHIFT) == 0) &&
+			    (xwrite_pos < width_out)) {
+				/* produce a new output sample */
+				offset += pixel_rate;
+				output_write_en = true;
+				xwrite_pos++;
+			}
+
+			if (nppc == XSCALER_PPC_4) {
+				xscaler->H_phases[x] |=
+					((u64)phaseH <<
+					 (s * XHSC_HPHASE_MUL_4PPC));
+				xscaler->H_phases[x] |=
+					((u64)array_idx <<
+					 (XHSC_HPHASE_SHIFT_BY_6 +
+					  (s * XHSC_HPHASE_MUL_4PPC)));
+				if (output_write_en)
+					xscaler->H_phases[x] |=
+						((u64)1 <<
+						 (XHSC_HPHASE_MULTIPLIER + s *
+						  XHSC_HPHASE_MUL_4PPC));
+			} else {
+				xscaler->H_phases[x] |=
+					(phaseH <<
+					 (s * XHSC_HPHASE_MULTIPLIER));
+				xscaler->H_phases[x] |=
+					(array_idx <<
+					 (XHSC_HPHASE_SHIFT_BY_6 +
+					  (s * XHSC_HPHASE_MULTIPLIER)));
+
+				if (output_write_en)
+					xscaler->H_phases[x] |=
+						(XV_HSCALER_PHASESH_V_OUTPUT_WR_EN <<
+						 (s * XHSC_HPHASE_MULTIPLIER));
+			}
+
+			if (get_new_pix)
+				nr_rds_clck++;
+		}
+		if (array_idx >= nppc)
+			array_idx &= (nppc - 1);
+
+		nr_rds += nr_rds_clck;
+		if (nr_rds >= nppc)
+			nr_rds -= nppc;
+	}
+}
+
+static void
+xv_hscaler_load_ext_coeff(struct xscaler_device *xscaler,
+			  const short *coeff, u32 ntaps)
+{
+	unsigned int i, j, pad, offset;
+	u32 nphases = xscaler->max_num_phases;
+
+	/* Determine if coefficient needs padding (effective vs. max taps) */
+	pad = XV_HSCALER_MAX_H_TAPS - ntaps;
+	offset = pad >> 1;
+	dev_dbg(xscaler->xvip.dev,
+		"%s : Pad = %d Offset = %d Nphases = %d ntaps = %d",
+			__func__, pad, offset, nphases, ntaps);
+
+	/* Load coefficients into scaler coefficient table */
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps; ++j)
+			xscaler->hscaler_coeff[i][j + offset] =
+						coeff[i * ntaps + j];
+	}
+
+	if (pad) { /* effective taps < max_taps */
+		for (i = 0; i < nphases; i++) {
+			/* pad left */
+			for (j = 0; j < offset; j++)
+				xscaler->hscaler_coeff[i][j] = 0;
+			/* pad right */
+			j = ntaps + offset;
+			for (; j < XV_HSCALER_MAX_H_TAPS; j++)
+				xscaler->hscaler_coeff[i][j] = 0;
+		}
+	}
+}
+
+static const short *xv_select_coeff(struct xscaler_device *xscaler,
+				    u32 in, u32 out, u32 *ntaps)
+{
+	const short *coeff = NULL;
+
+	/*
+	 * Scale Down Mode will use dynamic filter selection logic
+	 * Scale Up Mode (including 1:1) will always use 6 tap filter
+	 */
+	if (out < in) {
+		u16 scale_ratio = (in * 10) / out;
+
+		/* Since XV_HSCALER_TAPS_* is same as XV_VSCALER_TAPS_* */
+		switch (*ntaps) {
+		case XV_HSCALER_TAPS_6:
+			*ntaps = XV_HSCALER_TAPS_6;
+			if (scale_ratio > 35)
+				coeff = &XV_fixedcoeff_taps6_SR4[0][0];
+			else if (scale_ratio > 25)
+				coeff = &XV_fixedcoeff_taps6_SR3[0][0];
+			else if (scale_ratio > 15)
+				coeff = &XV_fixedcoeff_taps6_SR2[0][0];
+			else
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+			break;
+		case XV_HSCALER_TAPS_8:
+			if (scale_ratio > 35) {
+				coeff = &XV_fixedcoeff_taps8_SR4[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else if (scale_ratio > 25) {
+				coeff = &XV_fixedcoeff_taps8_SR3[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else if (scale_ratio > 15) {
+				coeff = &XV_fixedcoeff_taps8_SR2[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else {
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+				*ntaps = XV_HSCALER_TAPS_6;
+			}
+			break;
+		case XV_HSCALER_TAPS_10:
+			if (scale_ratio > 35) {
+				coeff = &XV_fixedcoeff_taps10_SR4[0][0];
+				*ntaps = XV_HSCALER_TAPS_10;
+			} else if (scale_ratio > 25) {
+				coeff = &XV_fixedcoeff_taps10_SR3[0][0];
+				*ntaps = XV_HSCALER_TAPS_10;
+			} else if (scale_ratio > 15) {
+				coeff = &XV_fixedcoeff_taps8_SR2[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else {
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+				*ntaps = XV_HSCALER_TAPS_6;
+			}
+			break;
+		case XV_HSCALER_TAPS_12:
+			if (scale_ratio > 35) {
+				coeff = &XV_fixedcoeff_taps12_SR4[0][0];
+				*ntaps = XV_HSCALER_TAPS_12;
+			} else if (scale_ratio > 25) {
+				coeff = &XV_fixedcoeff_taps10_SR3[0][0];
+				*ntaps = XV_HSCALER_TAPS_10;
+			} else if (scale_ratio > 15) {
+				coeff = &XV_fixedcoeff_taps8_SR2[0][0];
+				*ntaps = XV_HSCALER_TAPS_8;
+			} else {
+				coeff = &XV_fixedcoeff_taps6_SR1p2[0][0];
+				*ntaps = XV_HSCALER_TAPS_6;
+			}
+			break;
+		default:
+			dev_err(xscaler->xvip.dev,
+				"Unsupported number of taps = %d",
+				*ntaps);
+		}
+	} else {
+		dev_dbg(xscaler->xvip.dev, "scaler : scale up 6 tap");
+		coeff = &XV_lanczos2_taps6[0][0];
+		*ntaps = XV_HSCALER_TAPS_6;
+	}
+
+	return coeff;
+}
+
+/**
+ * xv_hscaler_coeff_select - Selection of H-Scaler coefficients of operation
+ * @xscaler: VPSS Scaler device information
+ * @width_in: Width of input video
+ * @width_out: Width of desired output video
+ *
+ * There are instances when a N-tap filter might operate in an M-tap
+ * configuration where N > M.
+ *
+ * For example :
+ * Depending on the ratio of scaling (while downscaling), a 12-tap
+ * filter may operate with 10 tap coefficients and zero-pads the remaining
+ * coefficients.
+ *
+ * While upscaling the driver will program 6-tap filter coefficients
+ * in any N-tap configurations (for N >= 6).
+ *
+ * This selection is adopted by the as it gives optimal
+ * video output determined by repeated testing of the IP
+ *
+ * Return: Will return 0 if successful. Returns -EINVAL on an unsupported
+ * H-scaler number of taps.
+ */
+static int
+xv_hscaler_select_coeff(struct xscaler_device *xscaler,
+			u32 width_in, u32 width_out)
+{
+	const short *coeff;
+	u32 ntaps = xscaler->num_hori_taps;
+
+	coeff = xv_select_coeff(xscaler, width_in, width_out, &ntaps);
+	if (!coeff)
+		return -EINVAL;
+
+	xv_hscaler_load_ext_coeff(xscaler, coeff, ntaps);
+	return 0;
+}
+
+static void xv_hscaler_set_coeff(struct xscaler_device *xscaler)
+{
+	int val, i, j, offset, rd_indx;
+	u32 ntaps = xscaler->num_hori_taps;
+	u32 nphases = xscaler->max_num_phases;
+	u32 base_addr;
+
+	offset = (XV_HSCALER_MAX_H_TAPS - ntaps) / 2;
+	base_addr = V_HSCALER_OFF + XV_HSCALER_CTRL_ADDR_HWREG_HFLTCOEFF_BASE;
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps / 2; j++) {
+			rd_indx = j * 2 + offset;
+			val = (xscaler->hscaler_coeff[i][rd_indx + 1] <<
+			       XSCALER_BITSHIFT_16) |
+			       (xscaler->hscaler_coeff[i][rd_indx] &
+			       XHSC_MASK_LOW_16BITS);
+			 xvip_write(&xscaler->xvip, base_addr +
+				    ((i * ntaps / 2 + j) * 4), val);
+		}
+	}
+}
+
+static void
+xv_vscaler_load_ext_coeff(struct xscaler_device *xscaler,
+			  const short *coeff, u32 ntaps)
+{
+	int i, j, pad, offset;
+	u32 nphases = xscaler->max_num_phases;
+
+	/* Determine if coefficient needs padding (effective vs. max taps) */
+	pad = XV_VSCALER_MAX_V_TAPS - ntaps;
+	offset = pad ? (pad >> 1) : 0;
+
+	dev_dbg(xscaler->xvip.dev,
+		"%s : Pad = %d Offset = %d Nphases = %d ntaps = %d",
+			__func__, pad, offset, nphases, ntaps);
+
+	/* Load User defined coefficients into scaler coefficient table */
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps; ++j)
+			xscaler->vscaler_coeff[i][j + offset] =
+						coeff[i * ntaps + j];
+	}
+
+	if (pad) { /* effective taps < max_taps */
+		for (i = 0; i < nphases; i++) {
+			/* pad left */
+			for (j = 0; j < offset; j++)
+				xscaler->vscaler_coeff[i][j] = 0;
+			/* pad right */
+			j = ntaps + offset;
+			for (; j < XV_VSCALER_MAX_V_TAPS; j++)
+				xscaler->vscaler_coeff[i][j] = 0;
+		}
+	}
+}
+
+static void xv_vscaler_set_coeff(struct xscaler_device *xscaler)
+{
+	u32 nphases = xscaler->max_num_phases;
+	u32 ntaps   = xscaler->num_vert_taps;
+	int val, i, j, offset, rd_indx;
+	u32 base_addr;
+
+	offset = (XV_VSCALER_MAX_V_TAPS - ntaps) / 2;
+	base_addr = V_VSCALER_OFF + XV_VSCALER_CTRL_ADDR_HWREG_VFLTCOEFF_BASE;
+
+	for (i = 0; i < nphases; i++) {
+		for (j = 0; j < ntaps / 2; j++) {
+			rd_indx = j * 2 + offset;
+			val = (xscaler->vscaler_coeff[i][rd_indx + 1] <<
+			       XSCALER_BITSHIFT_16) |
+			       (xscaler->vscaler_coeff[i][rd_indx] &
+			       XVSC_MASK_LOW_16BITS);
+			xvip_write(&xscaler->xvip,
+				   base_addr + ((i * ntaps / 2 + j) * 4), val);
+		}
+	}
+}
+
+/**
+ * xv_vscaler_coeff_select - Selection of V-Scaler coefficients of operation
+ * @xscaler: VPSS Scaler device information
+ * @height_in: Height of input video
+ * @height_out: Height of desired output video
+ *
+ * There are instances when a N-tap filter might operate in an M-tap
+ * configuration where N > M.
+ *
+ * For example :
+ * Depending on the ratio of scaling (while downscaling), a 10-tap
+ * filter may operate with 6 tap coefficients and zero-pads the remaining
+ * coefficients.
+ *
+ * While upscaling the driver will program 6-tap filter coefficients
+ * in any N-tap configurations (for N >= 6).
+ *
+ * This selection is adopted by the as it gives optimal
+ * video output determined by repeated testing of the IP
+ *
+ * Return: Will return 0 if successful. Returns -EINVAL on an unsupported
+ * V-scaler number of taps.
+ */
+static int
+xv_vscaler_select_coeff(struct xscaler_device *xscaler,
+			u32 height_in, u32 height_out)
+{
+	const short *coeff;
+	u32 ntaps = xscaler->num_vert_taps;
+
+	coeff = xv_select_coeff(xscaler, height_in, height_out, &ntaps);
+	if (!coeff)
+		return -EINVAL;
+
+	xv_vscaler_load_ext_coeff(xscaler, coeff, ntaps);
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Video Operations
+ */
+
+static inline void
+xv_procss_disable_block(struct xvip_device *xvip, u32 channel, u32 ip_block)
+{
+	xvip_clr(xvip, ((channel - 1) * XGPIO_CHAN_OFFSET) +
+		 XGPIO_DATA_OFFSET + S_AXIS_RESET_OFF,
+		 ip_block);
+}
+
+static inline void
+xv_procss_enable_block(struct xvip_device *xvip, u32 channel, u32 ip_block)
+{
+	xvip_set(xvip, ((channel - 1) * XGPIO_CHAN_OFFSET) +
+		 XGPIO_DATA_OFFSET + S_AXIS_RESET_OFF,
+		 ip_block);
+}
+
+static void xscaler_reset(struct xscaler_device *xscaler)
+{
+	xv_procss_disable_block(&xscaler->xvip, XGPIO_CH_RESET_SEL,
+				XGPIO_RESET_MASK_ALL_BLOCKS);
+	xv_procss_enable_block(&xscaler->xvip, XGPIO_CH_RESET_SEL,
+			       XGPIO_RESET_MASK_IP_AXIS);
+}
+
+static int
+xv_vscaler_setup_video_fmt(struct xscaler_device *xscaler, u32 code_in)
+{
+	u32 video_in;
+
+	switch (code_in) {
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+	case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		dev_dbg(xscaler->xvip.dev,
+			"Vscaler Input Media Format YUV 420");
+		video_in = XVIDC_CSF_YCRCB_420;
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+		dev_dbg(xscaler->xvip.dev,
+			"Vscaler Input Media Format YUV 422");
+		video_in = XVIDC_CSF_YCRCB_422;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+	case MEDIA_BUS_FMT_VUY10_1X30:
+		dev_dbg(xscaler->xvip.dev,
+			"Vscaler Input Media Format YUV 444");
+		video_in = XVIDC_CSF_YCRCB_444;
+		break;
+	case MEDIA_BUS_FMT_RBG888_1X24:
+	case MEDIA_BUS_FMT_RBG101010_1X30:
+		dev_dbg(xscaler->xvip.dev,
+			"Vscaler Input Media Format RGB");
+		video_in = XVIDC_CSF_RGB;
+		break;
+	default:
+		dev_err(xscaler->xvip.dev,
+			"Vscaler Unsupported Input Media Format 0x%x",
+			code_in);
+		return -EINVAL;
+	}
+	xvip_write(&xscaler->xvip, V_VSCALER_OFF +
+		   XV_VSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA,
+		   video_in);
+	/*
+	 * Vscaler will upscale to YUV 422 before
+	 * Hscaler starts operation
+	 */
+	if (video_in == XVIDC_CSF_YCRCB_420)
+		return XVIDC_CSF_YCRCB_422;
+	return video_in;
+}
+
+static int xv_hscaler_setup_video_fmt(struct xscaler_device *xscaler,
+				      u32 code_out, u32 vsc_out)
+{
+	u32 video_out;
+
+	switch (vsc_out) {
+	case XVIDC_CSF_YCRCB_422:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Input Media Format is YUV 422");
+		break;
+	case XVIDC_CSF_YCRCB_444:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Input Media Format is YUV 444");
+		break;
+	case XVIDC_CSF_RGB:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Input Media Format is RGB");
+		break;
+	default:
+		dev_err(xscaler->xvip.dev,
+			"Hscaler got unsupported format from Vscaler");
+		return -EINVAL;
+	}
+
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		XV_HSCALER_CTRL_ADDR_HWREG_COLORMODE_DATA,
+		vsc_out);
+
+	switch (code_out) {
+	case MEDIA_BUS_FMT_VYYUYY8_1X24:
+	case MEDIA_BUS_FMT_VYYUYY10_4X20:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Output Media Format YUV 420\n");
+		video_out = XVIDC_CSF_YCRCB_420;
+		break;
+	case MEDIA_BUS_FMT_UYVY8_1X16:
+	case MEDIA_BUS_FMT_UYVY10_1X20:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Output Media Format YUV 422\n");
+		video_out = XVIDC_CSF_YCRCB_422;
+		break;
+	case MEDIA_BUS_FMT_VUY8_1X24:
+	case MEDIA_BUS_FMT_VUY10_1X30:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Output Media Format YUV 444\n");
+		video_out = XVIDC_CSF_YCRCB_444;
+		break;
+	case MEDIA_BUS_FMT_RBG888_1X24:
+	case MEDIA_BUS_FMT_RBG101010_1X30:
+		dev_dbg(xscaler->xvip.dev,
+			"Hscaler Output Media Format RGB\n");
+		video_out = XVIDC_CSF_RGB;
+		break;
+	default:
+		dev_err(xscaler->xvip.dev,
+			"Hscaler Unsupported Output Media Format 0x%x",
+			code_out);
+		return -EINVAL;
+	}
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		   XV_HSCALER_CTRL_ADDR_HWREG_COLORMODEOUT_DATA,
+		   video_out);
+	return 0;
+}
+
+static void
+xv_hscaler_set_phases(struct xscaler_device *xscaler)
+{
+	u32 loop_width;
+	u32 index = 0, val;
+	u32 offset, i, j = 0, lsb, msb;
+	u64 phasehdata;
+
+	loop_width = xscaler->max_pixels / xscaler->pix_per_clk;
+
+	if (xscaler->cfg->flags & XSCALER_HPHASE_FIX) {
+		offset = V_HSCALER_OFF +
+			XV_HSCALER_CTRL_ADDR_HWREG_PHASEH_FIX;
+	} else {
+		offset = V_HSCALER_OFF +
+			XV_HSCALER_CTRL_ADDR_HWREG_PHASESH_V_BASE;
+	}
+
+	switch (xscaler->pix_per_clk) {
+	case XSCALER_PPC_1:
+		/*
+		 * phaseH is 64 bits but only lower 16 bits of each entry
+		 * is valid .Form a 32 bit word with 16bit LSB from 2
+		 * consecutive entries. Need 1 32b write to get 2 entries
+		 * into IP registers (i is array loc and index is
+		 * address offset)
+		 */
+		for (i = 0; i < loop_width; i += 2) {
+			lsb = lower_32_bits(xscaler->H_phases[i] &
+					    XHSC_MASK_LOW_16BITS);
+			msb = lower_32_bits(xscaler->H_phases[i + 1] &
+					    XHSC_MASK_LOW_16BITS);
+			val = (msb << 16 | lsb);
+			xvip_write(&xscaler->xvip, offset + (index * 4), val);
+			++index;
+		}
+		dev_dbg(xscaler->xvip.dev,
+			"%s : Operating in 1 PPC design", __func__);
+		return;
+	case XSCALER_PPC_2:
+		/*
+		 * PhaseH is 64bits but only lower 32b of each entry is valid
+		 * Need 1 32b write to get each entry into IP registers
+		 */
+		for (i = 0; i < loop_width; i++) {
+			val = lower_32_bits(xscaler->H_phases[i] &
+					    XHSC_MASK_LOW_32BITS);
+			xvip_write(&xscaler->xvip, offset + (i * 4), val);
+		}
+		dev_dbg(xscaler->xvip.dev,
+			"%s : Operating in 2 PPC design", __func__);
+		return;
+	case XSCALER_PPC_4:
+		/*
+		 * PhaseH is 64bits and each entry has valid 32b MSB & LSB
+		 * Need 2 32b writes to get each entry into IP registers
+		 * (index is array loc and offset is address offset)
+		 */
+		for (i = 0; i < loop_width; i++) {
+			phasehdata = xscaler->H_phases[index++];
+			lsb = (u32)(phasehdata & XHSC_MASK_LOW_32BITS);
+			msb = (u32)((phasehdata >> 32) & XHSC_MASK_LOW_32BITS);
+			xvip_write(&xscaler->xvip, offset + (j * 4), lsb);
+			xvip_write(&xscaler->xvip, offset + ((j + 1) * 4), msb);
+			j += 2;
+		}
+		dev_dbg(xscaler->xvip.dev,
+			"%s : Operating in 4 PPC design", __func__);
+		return;
+	default:
+		dev_warn(xscaler->xvip.dev, "%s : %d unsupported ppc design!!!\n",
+			 __func__, xscaler->pix_per_clk);
+	}
+}
+
+static int xscaler_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	u32 width_in, width_out;
+	u32 height_in, height_out;
+	u32 code_in, code_out;
+	u32 pixel_rate;
+	u32 line_rate;
+	int ret;
+
+	if (!enable) {
+		dev_dbg(xscaler->xvip.dev, "%s: Stream Off", __func__);
+		/* Reset the Global IP Reset through PS GPIO */
+		gpiod_set_value_cansleep(xscaler->rst_gpio,
+					 XSCALER_RESET_ASSERT);
+		gpiod_set_value_cansleep(xscaler->rst_gpio,
+					 XSCALER_RESET_DEASSERT);
+		xscaler_reset(xscaler);
+		memset(xscaler->H_phases, 0, sizeof(xscaler->H_phases));
+		return 0;
+	}
+
+	dev_dbg(xscaler->xvip.dev, "%s: Stream On", __func__);
+
+	/* Extract Sink Pad Information */
+	width_in = xscaler->formats[XVIP_PAD_SINK].width;
+	height_in = xscaler->formats[XVIP_PAD_SINK].height;
+	code_in = xscaler->formats[XVIP_PAD_SINK].code;
+
+	/* Extract Source Pad Information */
+	width_out = xscaler->formats[XVIP_PAD_SOURCE].width;
+	height_out = xscaler->formats[XVIP_PAD_SOURCE].height;
+	code_out = xscaler->formats[XVIP_PAD_SOURCE].code;
+
+	/*
+	 * V Scaler is before H Scaler
+	 * V-Scaler_setup
+	 */
+	line_rate = (height_in * STEP_PRECISION) / height_out;
+
+	if (xscaler->is_polyphase) {
+		ret = xv_vscaler_select_coeff(xscaler, height_in, height_out);
+		if (ret < 0)
+			return ret;
+		xv_vscaler_set_coeff(xscaler);
+	}
+
+	xvip_write(&xscaler->xvip, V_VSCALER_OFF +
+		   XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTIN_DATA, height_in);
+	xvip_write(&xscaler->xvip, V_VSCALER_OFF +
+		   XV_VSCALER_CTRL_ADDR_HWREG_WIDTH_DATA, width_in);
+	xvip_write(&xscaler->xvip, V_VSCALER_OFF +
+		   XV_VSCALER_CTRL_ADDR_HWREG_HEIGHTOUT_DATA, height_out);
+	xvip_write(&xscaler->xvip, V_VSCALER_OFF +
+		   XV_VSCALER_CTRL_ADDR_HWREG_LINERATE_DATA, line_rate);
+	ret = xv_vscaler_setup_video_fmt(xscaler, code_in);
+	if (ret < 0)
+		return ret;
+
+	/* H-Scaler_setup */
+	pixel_rate = (width_in * STEP_PRECISION) / width_out;
+
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		   XV_HSCALER_CTRL_ADDR_HWREG_HEIGHT_DATA, height_out);
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		   XV_HSCALER_CTRL_ADDR_HWREG_WIDTHIN_DATA, width_in);
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		   XV_HSCALER_CTRL_ADDR_HWREG_WIDTHOUT_DATA, width_out);
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		   XV_HSCALER_CTRL_ADDR_HWREG_PIXELRATE_DATA, pixel_rate);
+	ret = xv_hscaler_setup_video_fmt(xscaler, code_out, ret);
+	if (ret < 0)
+		return ret;
+
+	if (xscaler->is_polyphase) {
+		ret = xv_hscaler_select_coeff(xscaler, width_in, width_out);
+		if (ret < 0)
+			return ret;
+		xv_hscaler_set_coeff(xscaler);
+	}
+
+	xv_hscaler_calculate_phases(xscaler, width_in, width_out, pixel_rate);
+	xv_hscaler_set_phases(xscaler);
+
+	/* Start Scaler sub-cores */
+	xvip_write(&xscaler->xvip, V_HSCALER_OFF +
+		   XV_HSCALER_CTRL_ADDR_AP_CTRL, XSCALER_STREAM_ON);
+	xvip_write(&xscaler->xvip, V_VSCALER_OFF +
+		   XV_VSCALER_CTRL_ADDR_AP_CTRL, XSCALER_STREAM_ON);
+	xv_procss_enable_block(&xscaler->xvip, XGPIO_CH_RESET_SEL,
+			       XGPIO_RESET_MASK_VIDEO_IN);
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Pad Operations
+ */
+
+static int xscaler_enum_frame_size(struct v4l2_subdev *subdev,
+				   struct v4l2_subdev_state *sd_state,
+				   struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct v4l2_mbus_framefmt *format;
+	struct xscaler_device *xscaler = to_scaler(subdev);
+
+	format = v4l2_subdev_get_try_format(subdev, sd_state, fse->pad);
+	if (fse->index || fse->code != format->code)
+		return -EINVAL;
+
+	fse->min_width = XSCALER_MIN_WIDTH;
+	fse->max_width = xscaler->max_pixels;
+	fse->min_height = XSCALER_MIN_HEIGHT;
+	fse->max_height = xscaler->max_lines;
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+__xscaler_get_pad_format(struct xscaler_device *xscaler,
+			 struct v4l2_subdev_state *sd_state,
+			 unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		format = v4l2_subdev_get_try_format(&xscaler->xvip.subdev,
+						    sd_state,
+						    pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		format = &xscaler->formats[pad];
+		break;
+	default:
+		format = NULL;
+		break;
+	}
+
+	return format;
+}
+
+static int xscaler_get_format(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xscaler_get_pad_format(xscaler, sd_state, fmt->pad,
+					  fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	fmt->format = *format;
+
+	return 0;
+}
+
+static int xscaler_set_format(struct v4l2_subdev *subdev,
+			      struct v4l2_subdev_state *sd_state,
+			      struct v4l2_subdev_format *fmt)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = __xscaler_get_pad_format(xscaler, sd_state, fmt->pad,
+					  fmt->which);
+	if (!format)
+		return -EINVAL;
+
+	*format = fmt->format;
+
+	format->width = clamp_t(unsigned int, fmt->format.width,
+				XSCALER_MIN_WIDTH, xscaler->max_pixels);
+	format->height = clamp_t(unsigned int, fmt->format.height,
+				 XSCALER_MIN_HEIGHT, xscaler->max_lines);
+	format->code = fmt->format.code;
+	fmt->format = *format;
+	return 0;
+}
+
+/*
+ * V4L2 Subdevice Operations
+ */
+
+static int
+xscaler_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xscaler_device *xscaler = to_scaler(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	/* Initialize with default formats */
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xscaler->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state,
+					    XVIP_PAD_SOURCE);
+	*format = xscaler->default_formats[XVIP_PAD_SOURCE];
+
+	return 0;
+}
+
+static int
+xscaler_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static struct v4l2_subdev_video_ops xscaler_video_ops = {
+	.s_stream = xscaler_s_stream,
+};
+
+static struct v4l2_subdev_pad_ops xscaler_pad_ops = {
+	.enum_mbus_code		= xvip_enum_mbus_code,
+	.enum_frame_size	= xscaler_enum_frame_size,
+	.get_fmt		= xscaler_get_format,
+	.set_fmt		= xscaler_set_format,
+};
+
+static struct v4l2_subdev_ops xscaler_ops = {
+	.video  = &xscaler_video_ops,
+	.pad    = &xscaler_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xscaler_internal_ops = {
+	.open	= xscaler_open,
+	.close	= xscaler_close,
+};
+
+/*
+ * Media Operations
+ */
+
+static const struct media_entity_operations xscaler_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/*
+ * Platform Device Driver
+ */
+
+static int xscaler_parse_of(struct xscaler_device *xscaler)
+{
+	struct device *dev = xscaler->xvip.dev;
+	struct device_node *node = xscaler->xvip.dev->of_node;
+	const struct xvip_video_format *vip_format;
+	struct device_node *ports;
+	struct device_node *port;
+	int ret;
+	u32 port_id, dt_ppc = 0;
+
+	if (xscaler->cfg->flags & XSCALER_CLK_PROP) {
+		xscaler->aclk_axis = devm_clk_get(dev, "aclk_axis");
+		if (IS_ERR(xscaler->aclk_axis)) {
+			ret = PTR_ERR(xscaler->aclk_axis);
+			dev_err(dev, "failed to get aclk_axis (%d)\n", ret);
+			return ret;
+		}
+		xscaler->aclk_ctrl = devm_clk_get(dev, "aclk_ctrl");
+		if (IS_ERR(xscaler->aclk_ctrl)) {
+			ret = PTR_ERR(xscaler->aclk_ctrl);
+			dev_err(dev, "failed to get aclk_ctrl (%d)\n", ret);
+			return ret;
+		}
+	} else {
+		dev_info(dev, "assuming all required clocks are enabled!\n");
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-height",
+				   &xscaler->max_lines);
+	if (ret < 0) {
+		dev_err(dev, "xlnx,max-height is missing!");
+		return -EINVAL;
+	} else if (xscaler->max_lines > XSCALER_MAX_HEIGHT ||
+		   xscaler->max_lines < XSCALER_MIN_HEIGHT) {
+		dev_err(dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,max-width",
+				   &xscaler->max_pixels);
+	if (ret < 0) {
+		dev_err(dev, "xlnx,max-width is missing!");
+		return -EINVAL;
+	} else if (xscaler->max_pixels > XSCALER_MAX_WIDTH ||
+		   xscaler->max_pixels < XSCALER_MIN_WIDTH) {
+		dev_err(dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			vip_format = xvip_of_get_format(port);
+			if (IS_ERR(vip_format)) {
+				dev_err(dev, "invalid format in DT");
+				return PTR_ERR(vip_format);
+			}
+
+			ret = of_property_read_u32(port, "reg", &port_id);
+			if (ret < 0) {
+				dev_err(dev, "No reg in DT");
+				return ret;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "Invalid reg in DT");
+				return -EINVAL;
+			}
+			xscaler->vip_formats[port_id] = vip_format;
+		}
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-hori-taps",
+				   &xscaler->num_hori_taps);
+	if (ret < 0)
+		return ret;
+
+	switch (xscaler->num_hori_taps) {
+	case XV_HSCALER_TAPS_2:
+	case XV_HSCALER_TAPS_4:
+		xscaler->is_polyphase = false;
+		break;
+	case XV_HSCALER_TAPS_6:
+	case XV_HSCALER_TAPS_8:
+	case XV_HSCALER_TAPS_10:
+	case XV_HSCALER_TAPS_12:
+		xscaler->is_polyphase = true;
+		break;
+	default:
+		dev_err(dev, "Unsupported num-hori-taps %d",
+			xscaler->num_hori_taps);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-vert-taps",
+				   &xscaler->num_vert_taps);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * For Bilinear and Bicubic case
+	 * number of vertical and horizontal taps must match
+	 */
+	switch (xscaler->num_vert_taps) {
+	case XV_HSCALER_TAPS_2:
+	case XV_VSCALER_TAPS_4:
+		if (xscaler->num_vert_taps != xscaler->num_hori_taps) {
+			dev_err(dev,
+				"H-scaler taps %d mismatches V-scaler taps %d",
+				 xscaler->num_hori_taps,
+				 xscaler->num_vert_taps);
+			return -EINVAL;
+		}
+		break;
+	case XV_VSCALER_TAPS_6:
+	case XV_VSCALER_TAPS_8:
+	case XV_VSCALER_TAPS_10:
+	case XV_VSCALER_TAPS_12:
+		xscaler->is_polyphase = true;
+		break;
+	default:
+		dev_err(dev, "Unsupported num-vert-taps %d",
+			xscaler->num_vert_taps);
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,pix-per-clk", &dt_ppc);
+	if (ret < 0)
+		return ret;
+
+	/* Driver only supports 1 PPC and 2 PPC */
+	if (dt_ppc != XSCALER_PPC_1 && dt_ppc != XSCALER_PPC_2 &&
+	    dt_ppc != XSCALER_PPC_4) {
+		dev_err(xscaler->xvip.dev,
+			"Unsupported xlnx,pix-per-clk(%d) value in DT", dt_ppc);
+		return -EINVAL;
+	}
+	xscaler->pix_per_clk = dt_ppc;
+
+	/* Reset GPIO */
+	xscaler->rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(xscaler->rst_gpio)) {
+		if (PTR_ERR(xscaler->rst_gpio) != -EPROBE_DEFER)
+			dev_err(dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(xscaler->rst_gpio);
+	}
+
+	return 0;
+}
+
+static int xscaler_probe(struct platform_device *pdev)
+{
+	struct xscaler_device *xscaler;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *default_format;
+	int ret;
+	const struct of_device_id *match;
+	struct device_node *node = pdev->dev.of_node;
+	struct resource *res;
+
+	xscaler = devm_kzalloc(&pdev->dev, sizeof(*xscaler), GFP_KERNEL);
+	if (!xscaler)
+		return -ENOMEM;
+
+	xscaler->xvip.dev = &pdev->dev;
+
+	match = of_match_node(xscaler_of_id_table, node);
+	if (!match)
+		return -ENODEV;
+
+	if (!strcmp(xscaler_of_id_table[0].compatible, match->compatible)) {
+		dev_warn(&pdev->dev,
+			 "%s - compatible string is getting deprecated!\n",
+			 match->compatible);
+	}
+
+	xscaler->cfg = match->data;
+
+	ret = xscaler_parse_of(xscaler);
+	if (ret < 0)
+		return ret;
+
+	/* Initialize coefficient parameters */
+	xscaler->max_num_phases = XSCALER_MAX_PHASES;
+
+	if (xscaler->cfg->flags & XSCALER_CLK_PROP) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		xscaler->xvip.iomem = devm_ioremap_resource(xscaler->xvip.dev,
+							    res);
+		if (IS_ERR(xscaler->xvip.iomem))
+			return PTR_ERR(xscaler->xvip.iomem);
+
+		ret = clk_prepare_enable(xscaler->aclk_axis);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to enable aclk_axis (%d)\n",
+				ret);
+			goto res_cleanup;
+		}
+
+		ret = clk_prepare_enable(xscaler->aclk_ctrl);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to enable aclk_ctrl (%d)\n",
+				ret);
+			goto axis_clk_cleanup;
+		}
+	} else {
+		ret = xvip_init_resources(&xscaler->xvip);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* Reset the Global IP Reset through a PS GPIO */
+	gpiod_set_value_cansleep(xscaler->rst_gpio, XSCALER_RESET_DEASSERT);
+	/* Reset internal GPIO within the IP */
+	xscaler_reset(xscaler);
+
+	/* Initialize V4L2 subdevice and media entity */
+	subdev = &xscaler->xvip.subdev;
+	v4l2_subdev_init(subdev, &xscaler_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xscaler_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xscaler);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Initialize default and active formats */
+	default_format = &xscaler->default_formats[XVIP_PAD_SINK];
+	default_format->code = xscaler->vip_formats[XVIP_PAD_SINK]->code;
+	default_format->field = V4L2_FIELD_NONE;
+	default_format->colorspace = V4L2_COLORSPACE_SRGB;
+	default_format->width = XSCALER_DEF_IN_WIDTH;
+	default_format->height = XSCALER_DEF_IN_HEIGHT;
+	xscaler->formats[XVIP_PAD_SINK] = *default_format;
+
+	default_format = &xscaler->default_formats[XVIP_PAD_SOURCE];
+	*default_format = xscaler->default_formats[XVIP_PAD_SINK];
+	default_format->code = xscaler->vip_formats[XVIP_PAD_SOURCE]->code;
+	default_format->width = XSCALER_DEF_OUT_WIDTH;
+	default_format->height = XSCALER_DEF_OUT_HEIGHT;
+	xscaler->formats[XVIP_PAD_SOURCE] = *default_format;
+
+	xscaler->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xscaler->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xscaler_media_ops;
+
+	ret = media_entity_pads_init(&subdev->entity, 2, xscaler->pads);
+	if (ret < 0)
+		goto error;
+
+	platform_set_drvdata(pdev, xscaler);
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev");
+		goto error;
+	}
+	dev_info(xscaler->xvip.dev, "Num Hori Taps %d",
+		 xscaler->num_hori_taps);
+	dev_info(xscaler->xvip.dev, "Num Vert Taps %d",
+		 xscaler->num_vert_taps);
+	dev_info(&pdev->dev, "VPSS Scaler Probe Successful");
+	return 0;
+
+error:
+	media_entity_cleanup(&subdev->entity);
+	clk_disable_unprepare(xscaler->aclk_ctrl);
+axis_clk_cleanup:
+	clk_disable_unprepare(xscaler->aclk_axis);
+res_cleanup:
+	xvip_cleanup_resources(&xscaler->xvip);
+	return ret;
+}
+
+static int xscaler_remove(struct platform_device *pdev)
+{
+	struct xscaler_device *xscaler = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xscaler->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+	clk_disable_unprepare(xscaler->aclk_ctrl);
+	clk_disable_unprepare(xscaler->aclk_axis);
+	xvip_cleanup_resources(&xscaler->xvip);
+
+	return 0;
+}
+
+static struct platform_driver xscaler_driver = {
+	.driver			= {
+		.name		= "xilinx-vpss-scaler",
+		.of_match_table	= xscaler_of_id_table,
+	},
+	.probe			= xscaler_probe,
+	.remove			= xscaler_remove,
+};
+
+module_platform_driver(xscaler_driver);
+MODULE_DESCRIPTION("Xilinx Scaler VPSS Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vtc.c
@@ -141,6 +141,9 @@
 
 #define XVTC_GENERATOR_GLOBAL_DELAY		0x0104
 
+/* Value of 1 = .01% */
+#define XVTC_CLK_MAX_PCT_ERR			1
+
 /**
  * struct xvtc_device - Xilinx Video Timing Controller device structure
  * @xvip: Xilinx Video IP device
@@ -175,10 +178,25 @@
 			 const struct xvtc_config *config)
 {
 	int ret;
+	unsigned long s_rate;
+	unsigned long g_rate;
+	unsigned long clk_err;
 
 	if (!xvtc->has_generator)
 		return -ENXIO;
 
+	s_rate = (unsigned long)config->fps * config->hsize * config->vsize;
+	ret = clk_set_rate(xvtc->xvip.clk, s_rate);
+	if (ret < 0)
+		return ret;
+
+	/* Verify that the clock is within a reasonable tolerance. */
+	g_rate = clk_get_rate(xvtc->xvip.clk);
+	clk_err = (abs(g_rate - s_rate) * 10000) / (s_rate);
+	if (clk_err > XVTC_CLK_MAX_PCT_ERR)
+		dev_warn(xvtc->xvip.dev, "Failed to set clk rate: %lu, actual rate: %lu\n",
+				s_rate, g_rate);
+
 	ret = clk_prepare_enable(xvtc->xvip.clk);
 	if (ret < 0)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/platform/xilinx/xilinx-vtc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/platform/xilinx/xilinx-vtc.h
@@ -27,6 +27,7 @@
 	unsigned int vsync_start;
 	unsigned int vsync_end;
 	unsigned int vsize;
+	unsigned int fps;
 };
 
 struct xvtc_device *xvtc_of_get(struct device_node *np);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/radio-isa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/radio-isa.c
@@ -36,7 +36,7 @@
 
 	strscpy(v->driver, isa->drv->driver.driver.name, sizeof(v->driver));
 	strscpy(v->card, isa->drv->card, sizeof(v->card));
-	snprintf(v->bus_info, sizeof(v->bus_info), "ISA:%s", isa->v4l2_dev.name);
+	snprintf(v->bus_info, sizeof(v->bus_info), "ISA:%s", dev_name(isa->v4l2_dev.dev));
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/radio-shark.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/radio-shark.c
@@ -316,6 +316,16 @@
 {
 	struct shark_device *shark;
 	int retval = -ENOMEM;
+	static const u8 ep_addresses[] = {
+		SHARK_IN_EP | USB_DIR_IN,
+		SHARK_OUT_EP | USB_DIR_OUT,
+		0};
+
+	/* Are the expected endpoints present? */
+	if (!usb_check_int_endpoints(intf, ep_addresses)) {
+		dev_err(&intf->dev, "Invalid radioSHARK device\n");
+		return -EINVAL;
+	}
 
 	shark = kzalloc(sizeof(struct shark_device), GFP_KERNEL);
 	if (!shark)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/radio-shark2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/radio-shark2.c
@@ -62,7 +62,7 @@
 #ifdef SHARK_USE_LEDS
 	struct work_struct led_work;
 	struct led_classdev leds[NO_LEDS];
-	char led_names[NO_LEDS][32];
+	char led_names[NO_LEDS][64];
 	atomic_t brightness[NO_LEDS];
 	unsigned long brightness_new;
 #endif
@@ -282,6 +282,16 @@
 {
 	struct shark_device *shark;
 	int retval = -ENOMEM;
+	static const u8 ep_addresses[] = {
+		SHARK_IN_EP | USB_DIR_IN,
+		SHARK_OUT_EP | USB_DIR_OUT,
+		0};
+
+	/* Are the expected endpoints present? */
+	if (!usb_check_int_endpoints(intf, ep_addresses)) {
+		dev_err(&intf->dev, "Invalid radioSHARK2 device\n");
+		return -EINVAL;
+	}
 
 	shark = kzalloc(sizeof(struct shark_device), GFP_KERNEL);
 	if (!shark)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/radio-wl1273.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/radio-wl1273.c
@@ -1279,7 +1279,7 @@
 
 	strscpy(capability->driver, WL1273_FM_DRIVER_NAME,
 		sizeof(capability->driver));
-	strscpy(capability->card, "Texas Instruments Wl1273 FM Radio",
+	strscpy(capability->card, "TI Wl1273 FM Radio",
 		sizeof(capability->card));
 	strscpy(capability->bus_info, radio->bus_type,
 		sizeof(capability->bus_info));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/si470x/radio-si470x-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/si470x/radio-si470x-i2c.c
@@ -11,7 +11,7 @@
 
 /* driver definitions */
 #define DRIVER_AUTHOR "Joonyoung Shim <jy0922.shim@samsung.com>";
-#define DRIVER_CARD "Silicon Labs Si470x FM Radio Receiver"
+#define DRIVER_CARD "Silicon Labs Si470x FM Radio"
 #define DRIVER_DESC "I2C radio driver for Si470x FM Radio Receivers"
 #define DRIVER_VERSION "1.0.2"
 
@@ -368,7 +368,7 @@
 	if (radio->hdl.error) {
 		retval = radio->hdl.error;
 		dev_err(&client->dev, "couldn't register control\n");
-		goto err_dev;
+		goto err_all;
 	}
 
 	/* video device initialization */
@@ -463,7 +463,6 @@
 	return 0;
 err_all:
 	v4l2_ctrl_handler_free(&radio->hdl);
-err_dev:
 	v4l2_device_unregister(&radio->v4l2_dev);
 err_initial:
 	return retval;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/si470x/radio-si470x-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/si470x/radio-si470x-usb.c
@@ -16,7 +16,7 @@
 
 /* driver definitions */
 #define DRIVER_AUTHOR "Tobias Lorenz <tobias.lorenz@gmx.net>"
-#define DRIVER_CARD "Silicon Labs Si470x FM Radio Receiver"
+#define DRIVER_CARD "Silicon Labs Si470x FM Radio"
 #define DRIVER_DESC "USB radio driver for Si470x FM Radio Receivers"
 #define DRIVER_VERSION "1.0.10"
 
@@ -733,8 +733,10 @@
 
 	/* start radio */
 	retval = si470x_start_usb(radio);
-	if (retval < 0)
+	if (retval < 0 && !radio->int_in_running)
 		goto err_buf;
+	else if (retval < 0)	/* in case of radio->int_in_running == 1 */
+		goto err_all;
 
 	/* set initial frequency */
 	si470x_set_freq(radio, 87.5 * FREQ_MUL); /* available in all regions */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/radio/wl128x/fmdrv_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/radio/wl128x/fmdrv_common.c
@@ -465,11 +465,12 @@
 			   jiffies_to_msecs(FM_DRV_TX_TIMEOUT) / 1000);
 		return -ETIMEDOUT;
 	}
+	spin_lock_irqsave(&fmdev->resp_skb_lock, flags);
 	if (!fmdev->resp_skb) {
+		spin_unlock_irqrestore(&fmdev->resp_skb_lock, flags);
 		fmerr("Response SKB is missing\n");
 		return -EFAULT;
 	}
-	spin_lock_irqsave(&fmdev->resp_skb_lock, flags);
 	skb = fmdev->resp_skb;
 	fmdev->resp_skb = NULL;
 	spin_unlock_irqrestore(&fmdev->resp_skb_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/bpf-lirc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/bpf-lirc.c
@@ -249,7 +249,7 @@
 	if (attr->attach_flags)
 		return -EINVAL;
 
-	rcdev = rc_dev_get_from_fd(attr->target_fd);
+	rcdev = rc_dev_get_from_fd(attr->target_fd, true);
 	if (IS_ERR(rcdev))
 		return PTR_ERR(rcdev);
 
@@ -274,7 +274,7 @@
 	if (IS_ERR(prog))
 		return PTR_ERR(prog);
 
-	rcdev = rc_dev_get_from_fd(attr->target_fd);
+	rcdev = rc_dev_get_from_fd(attr->target_fd, true);
 	if (IS_ERR(rcdev)) {
 		bpf_prog_put(prog);
 		return PTR_ERR(rcdev);
@@ -299,7 +299,7 @@
 	if (attr->query.query_flags)
 		return -EINVAL;
 
-	rcdev = rc_dev_get_from_fd(attr->query.target_fd);
+	rcdev = rc_dev_get_from_fd(attr->query.target_fd, false);
 	if (IS_ERR(rcdev))
 		return PTR_ERR(rcdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/ene_ir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/ene_ir.c
@@ -1106,6 +1106,8 @@
 	struct ene_device *dev = pnp_get_drvdata(pnp_dev);
 	unsigned long flags;
 
+	rc_unregister_device(dev->rdev);
+	del_timer_sync(&dev->tx_sim_timer);
 	spin_lock_irqsave(&dev->hw_lock, flags);
 	ene_rx_disable(dev);
 	ene_rx_restore_hw_buffer(dev);
@@ -1113,7 +1115,6 @@
 
 	free_irq(dev->irq, dev);
 	release_region(dev->hw_io, ENE_IO_SIZE);
-	rc_unregister_device(dev->rdev);
 	kfree(dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/gpio-ir-recv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/gpio-ir-recv.c
@@ -107,6 +107,8 @@
 		rcdev->map_name = RC_MAP_EMPTY;
 
 	gpio_dev->rcdev = rcdev;
+	if (of_property_read_bool(np, "wakeup-source"))
+		device_init_wakeup(dev, true);
 
 	rc = devm_rc_register_device(dev, rcdev);
 	if (rc < 0) {
@@ -130,6 +132,23 @@
 				"gpio-ir-recv-irq", gpio_dev);
 }
 
+static int gpio_ir_recv_remove(struct platform_device *pdev)
+{
+	struct gpio_rc_dev *gpio_dev = platform_get_drvdata(pdev);
+	struct device *pmdev = gpio_dev->pmdev;
+
+	if (pmdev) {
+		pm_runtime_get_sync(pmdev);
+		cpu_latency_qos_remove_request(&gpio_dev->qos);
+
+		pm_runtime_disable(pmdev);
+		pm_runtime_put_noidle(pmdev);
+		pm_runtime_set_suspended(pmdev);
+	}
+
+	return 0;
+}
+
 #ifdef CONFIG_PM
 static int gpio_ir_recv_suspend(struct device *dev)
 {
@@ -189,6 +208,7 @@
 
 static struct platform_driver gpio_ir_recv_driver = {
 	.probe  = gpio_ir_recv_probe,
+	.remove = gpio_ir_recv_remove,
 	.driver = {
 		.name   = KBUILD_MODNAME,
 		.of_match_table = of_match_ptr(gpio_ir_recv_of_match),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/gpio-ir-tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/gpio-ir-tx.c
@@ -48,11 +48,29 @@
 	return 0;
 }
 
+static void delay_until(ktime_t until)
+{
+	/*
+	 * delta should never exceed 0.5 seconds (IR_MAX_DURATION) and on
+	 * m68k ndelay(s64) does not compile; so use s32 rather than s64.
+	 */
+	s32 delta;
+
+	while (true) {
+		delta = ktime_us_delta(until, ktime_get());
+		if (delta <= 0)
+			return;
+
+		/* udelay more than 1ms may not work */
+		delta = min(delta, 1000);
+		udelay(delta);
+	}
+}
+
 static void gpio_ir_tx_unmodulated(struct gpio_ir *gpio_ir, uint *txbuf,
 				   uint count)
 {
 	ktime_t edge;
-	s32 delta;
 	int i;
 
 	local_irq_disable();
@@ -63,9 +81,7 @@
 		gpiod_set_value(gpio_ir->gpio, !(i % 2));
 
 		edge = ktime_add_us(edge, txbuf[i]);
-		delta = ktime_us_delta(edge, ktime_get());
-		if (delta > 0)
-			udelay(delta);
+		delay_until(edge);
 	}
 
 	gpiod_set_value(gpio_ir->gpio, 0);
@@ -97,9 +113,7 @@
 		if (i % 2) {
 			// space
 			edge = ktime_add_us(edge, txbuf[i]);
-			delta = ktime_us_delta(edge, ktime_get());
-			if (delta > 0)
-				udelay(delta);
+			delay_until(edge);
 		} else {
 			// pulse
 			ktime_t last = ktime_add_us(edge, txbuf[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/igorplugusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/igorplugusb.c
@@ -64,9 +64,11 @@
 	if (start >= len) {
 		dev_err(ir->dev, "receive overflow invalid: %u", overflow);
 	} else {
-		if (overflow > 0)
+		if (overflow > 0) {
 			dev_warn(ir->dev, "receive overflow, at least %u lost",
 								overflow);
+			ir_raw_event_reset(ir->rc);
+		}
 
 		do {
 			rawir.duration = ir->buf_in[i] * 85;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/iguanair.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/iguanair.c
@@ -197,8 +197,10 @@
 	if (rc)
 		return rc;
 
-	if (wait_for_completion_timeout(&ir->completion, TIMEOUT) == 0)
+	if (wait_for_completion_timeout(&ir->completion, TIMEOUT) == 0) {
+		usb_kill_urb(ir->urb_out);
 		return -ETIMEDOUT;
+	}
 
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/imon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/imon.c
@@ -153,6 +153,24 @@
 	const struct imon_usb_dev_descr *dev_descr;
 					/* device description with key */
 					/* table for front panels */
+	/*
+	 * Fields for deferring free_imon_context().
+	 *
+	 * Since reference to "struct imon_context" is stored into
+	 * "struct file"->private_data, we need to remember
+	 * how many file descriptors might access this "struct imon_context".
+	 */
+	refcount_t users;
+	/*
+	 * Use a flag for telling display_open()/vfd_write()/lcd_write() that
+	 * imon_disconnect() was already called.
+	 */
+	bool disconnected;
+	/*
+	 * We need to wait for RCU grace period in order to allow
+	 * display_open() to safely check ->disconnected and increment ->users.
+	 */
+	struct rcu_head rcu;
 };
 
 #define TOUCH_TIMEOUT	(HZ/30)
@@ -160,18 +178,18 @@
 /* vfd character device file operations */
 static const struct file_operations vfd_fops = {
 	.owner		= THIS_MODULE,
-	.open		= &display_open,
-	.write		= &vfd_write,
-	.release	= &display_close,
+	.open		= display_open,
+	.write		= vfd_write,
+	.release	= display_close,
 	.llseek		= noop_llseek,
 };
 
 /* lcd character device file operations */
 static const struct file_operations lcd_fops = {
 	.owner		= THIS_MODULE,
-	.open		= &display_open,
-	.write		= &lcd_write,
-	.release	= &display_close,
+	.open		= display_open,
+	.write		= lcd_write,
+	.release	= display_close,
 	.llseek		= noop_llseek,
 };
 
@@ -439,9 +457,6 @@
 	.id_table	= imon_usb_id_table,
 };
 
-/* to prevent races between open() and disconnect(), probing, etc */
-static DEFINE_MUTEX(driver_lock);
-
 /* Module bookkeeping bits */
 MODULE_AUTHOR(MOD_AUTHOR);
 MODULE_DESCRIPTION(MOD_DESC);
@@ -481,9 +496,11 @@
 	struct device *dev = ictx->dev;
 
 	usb_free_urb(ictx->tx_urb);
+	WARN_ON(ictx->dev_present_intf0);
 	usb_free_urb(ictx->rx_urb_intf0);
+	WARN_ON(ictx->dev_present_intf1);
 	usb_free_urb(ictx->rx_urb_intf1);
-	kfree(ictx);
+	kfree_rcu(ictx, rcu);
 
 	dev_dbg(dev, "%s: iMON context freed\n", __func__);
 }
@@ -499,9 +516,6 @@
 	int subminor;
 	int retval = 0;
 
-	/* prevent races with disconnect */
-	mutex_lock(&driver_lock);
-
 	subminor = iminor(inode);
 	interface = usb_find_interface(&imon_driver, subminor);
 	if (!interface) {
@@ -509,13 +523,16 @@
 		retval = -ENODEV;
 		goto exit;
 	}
-	ictx = usb_get_intfdata(interface);
 
-	if (!ictx) {
+	rcu_read_lock();
+	ictx = usb_get_intfdata(interface);
+	if (!ictx || ictx->disconnected || !refcount_inc_not_zero(&ictx->users)) {
+		rcu_read_unlock();
 		pr_err("no context found for minor %d\n", subminor);
 		retval = -ENODEV;
 		goto exit;
 	}
+	rcu_read_unlock();
 
 	mutex_lock(&ictx->lock);
 
@@ -533,8 +550,10 @@
 
 	mutex_unlock(&ictx->lock);
 
+	if (retval && refcount_dec_and_test(&ictx->users))
+		free_imon_context(ictx);
+
 exit:
-	mutex_unlock(&driver_lock);
 	return retval;
 }
 
@@ -544,16 +563,9 @@
  */
 static int display_close(struct inode *inode, struct file *file)
 {
-	struct imon_context *ictx = NULL;
+	struct imon_context *ictx = file->private_data;
 	int retval = 0;
 
-	ictx = file->private_data;
-
-	if (!ictx) {
-		pr_err("no context for device\n");
-		return -ENODEV;
-	}
-
 	mutex_lock(&ictx->lock);
 
 	if (!ictx->display_supported) {
@@ -568,6 +580,8 @@
 	}
 
 	mutex_unlock(&ictx->lock);
+	if (refcount_dec_and_test(&ictx->users))
+		free_imon_context(ictx);
 	return retval;
 }
 
@@ -632,15 +646,14 @@
 		pr_err_ratelimited("error submitting urb(%d)\n", retval);
 	} else {
 		/* Wait for transmission to complete (or abort) */
-		mutex_unlock(&ictx->lock);
 		retval = wait_for_completion_interruptible(
 				&ictx->tx.finished);
 		if (retval) {
 			usb_kill_urb(ictx->tx_urb);
 			pr_err_ratelimited("task interrupted\n");
 		}
-		mutex_lock(&ictx->lock);
 
+		ictx->tx.busy = false;
 		retval = ictx->tx.status;
 		if (retval)
 			pr_err_ratelimited("packet tx failed (%d)\n", retval);
@@ -934,17 +947,15 @@
 	int offset;
 	int seq;
 	int retval = 0;
-	struct imon_context *ictx;
+	struct imon_context *ictx = file->private_data;
 	static const unsigned char vfd_packet6[] = {
 		0x01, 0x00, 0x00, 0x00, 0x00, 0xFF, 0xFF };
 
-	ictx = file->private_data;
-	if (!ictx) {
-		pr_err_ratelimited("no context for device\n");
+	if (ictx->disconnected)
 		return -ENODEV;
-	}
 
-	mutex_lock(&ictx->lock);
+	if (mutex_lock_interruptible(&ictx->lock))
+		return -ERESTARTSYS;
 
 	if (!ictx->dev_present_intf0) {
 		pr_err_ratelimited("no iMON device present\n");
@@ -1018,13 +1029,10 @@
 			 size_t n_bytes, loff_t *pos)
 {
 	int retval = 0;
-	struct imon_context *ictx;
+	struct imon_context *ictx = file->private_data;
 
-	ictx = file->private_data;
-	if (!ictx) {
-		pr_err_ratelimited("no context for device\n");
+	if (ictx->disconnected)
 		return -ENODEV;
-	}
 
 	mutex_lock(&ictx->lock);
 
@@ -1142,10 +1150,7 @@
 
 	memcpy(ictx->usb_tx_buf, &ir_proto_packet, sizeof(ir_proto_packet));
 
-	if (!mutex_is_locked(&ictx->lock)) {
-		unlock = true;
-		mutex_lock(&ictx->lock);
-	}
+	unlock = mutex_trylock(&ictx->lock);
 
 	retval = send_packet(ictx);
 	if (retval)
@@ -2402,7 +2407,6 @@
 	int ifnum, sysfs_err;
 	int ret = 0;
 	struct imon_context *ictx = NULL;
-	struct imon_context *first_if_ctx = NULL;
 	u16 vendor, product;
 
 	usbdev     = usb_get_dev(interface_to_usbdev(interface));
@@ -2414,16 +2418,17 @@
 	dev_dbg(dev, "%s: found iMON device (%04x:%04x, intf%d)\n",
 		__func__, vendor, product, ifnum);
 
-	/* prevent races probing devices w/multiple interfaces */
-	mutex_lock(&driver_lock);
-
 	first_if = usb_ifnum_to_if(usbdev, 0);
 	if (!first_if) {
 		ret = -ENODEV;
 		goto fail;
 	}
 
-	first_if_ctx = usb_get_intfdata(first_if);
+	if (first_if->dev.driver != interface->dev.driver) {
+		dev_err(&interface->dev, "inconsistent driver matching\n");
+		ret = -EINVAL;
+		goto fail;
+	}
 
 	if (ifnum == 0) {
 		ictx = imon_init_intf0(interface, id);
@@ -2432,9 +2437,11 @@
 			ret = -ENODEV;
 			goto fail;
 		}
+		refcount_set(&ictx->users, 1);
 
 	} else {
 		/* this is the secondary interface on the device */
+		struct imon_context *first_if_ctx = usb_get_intfdata(first_if);
 
 		/* fail early if first intf failed to register */
 		if (!first_if_ctx) {
@@ -2448,14 +2455,13 @@
 			ret = -ENODEV;
 			goto fail;
 		}
+		refcount_inc(&ictx->users);
 
 	}
 
 	usb_set_intfdata(interface, ictx);
 
 	if (ifnum == 0) {
-		mutex_lock(&ictx->lock);
-
 		if (product == 0xffdc && ictx->rf_device) {
 			sysfs_err = sysfs_create_group(&interface->dev.kobj,
 						       &imon_rf_attr_group);
@@ -2466,21 +2472,17 @@
 
 		if (ictx->display_supported)
 			imon_init_display(ictx, interface);
-
-		mutex_unlock(&ictx->lock);
 	}
 
 	dev_info(dev, "iMON device (%04x:%04x, intf%d) on usb<%d:%d> initialized\n",
 		 vendor, product, ifnum,
 		 usbdev->bus->busnum, usbdev->devnum);
 
-	mutex_unlock(&driver_lock);
 	usb_put_dev(usbdev);
 
 	return 0;
 
 fail:
-	mutex_unlock(&driver_lock);
 	usb_put_dev(usbdev);
 	dev_err(dev, "unable to register, err %d\n", ret);
 
@@ -2496,10 +2498,8 @@
 	struct device *dev;
 	int ifnum;
 
-	/* prevent races with multi-interface device probing and display_open */
-	mutex_lock(&driver_lock);
-
 	ictx = usb_get_intfdata(interface);
+	ictx->disconnected = true;
 	dev = ictx->dev;
 	ifnum = interface->cur_altsetting->desc.bInterfaceNumber;
 
@@ -2540,11 +2540,9 @@
 		}
 	}
 
-	if (!ictx->dev_present_intf0 && !ictx->dev_present_intf1)
+	if (refcount_dec_and_test(&ictx->users))
 		free_imon_context(ictx);
 
-	mutex_unlock(&driver_lock);
-
 	dev_dbg(dev, "%s: iMON device (intf%d) disconnected\n",
 		__func__, ifnum);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/ir-sharp-decoder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/ir-sharp-decoder.c
@@ -15,7 +15,9 @@
 #define SHARP_UNIT		40  /* us */
 #define SHARP_BIT_PULSE		(8    * SHARP_UNIT) /* 320us */
 #define SHARP_BIT_0_PERIOD	(25   * SHARP_UNIT) /* 1ms (680us space) */
-#define SHARP_BIT_1_PERIOD	(50   * SHARP_UNIT) /* 2ms (1680ms space) */
+#define SHARP_BIT_1_PERIOD	(50   * SHARP_UNIT) /* 2ms (1680us space) */
+#define SHARP_BIT_0_SPACE	(17   * SHARP_UNIT) /* 680us space */
+#define SHARP_BIT_1_SPACE	(42   * SHARP_UNIT) /* 1680us space */
 #define SHARP_ECHO_SPACE	(1000 * SHARP_UNIT) /* 40 ms */
 #define SHARP_TRAILER_SPACE	(125  * SHARP_UNIT) /* 5 ms (even longer) */
 
@@ -168,8 +170,8 @@
 	.header_pulse  = 0,
 	.header_space  = 0,
 	.bit_pulse     = SHARP_BIT_PULSE,
-	.bit_space[0]  = SHARP_BIT_0_PERIOD,
-	.bit_space[1]  = SHARP_BIT_1_PERIOD,
+	.bit_space[0]  = SHARP_BIT_0_SPACE,
+	.bit_space[1]  = SHARP_BIT_1_SPACE,
 	.trailer_pulse = SHARP_BIT_PULSE,
 	.trailer_space = SHARP_ECHO_SPACE,
 	.msb_first     = 1,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/ir_toy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/ir_toy.c
@@ -324,6 +324,7 @@
 			    sizeof(COMMAND_SMODE_EXIT), STATE_RESET);
 	if (err) {
 		dev_err(irtoy->dev, "exit sample mode: %d\n", err);
+		kfree(buf);
 		return err;
 	}
 
@@ -331,6 +332,7 @@
 			    sizeof(COMMAND_SMODE_ENTER), STATE_COMMAND);
 	if (err) {
 		dev_err(irtoy->dev, "enter sample mode: %d\n", err);
+		kfree(buf);
 		return err;
 	}
 
@@ -429,7 +431,7 @@
 	err = usb_submit_urb(irtoy->urb_in, GFP_KERNEL);
 	if (err != 0) {
 		dev_err(irtoy->dev, "fail to submit in urb: %d\n", err);
-		return err;
+		goto free_rcdev;
 	}
 
 	err = irtoy_setup(irtoy);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/ite-cir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/ite-cir.c
@@ -242,7 +242,7 @@
 	}
 
 	/* check for the receive interrupt */
-	if (iflags & ITE_IRQ_RX_FIFO) {
+	if (iflags & (ITE_IRQ_RX_FIFO | ITE_IRQ_RX_FIFO_OVERRUN)) {
 		/* read the FIFO bytes */
 		rx_bytes = dev->params->get_rx_bytes(dev, rx_buf,
 						    ITE_RX_FIFO_LEN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/lirc_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/lirc_dev.c
@@ -287,7 +287,11 @@
 		if (ret < 0)
 			goto out_kfree_raw;
 
-		count = ret;
+		/* drop trailing space */
+		if (!(ret % 2))
+			count = ret - 1;
+		else
+			count = ret;
 
 		txbuf = kmalloc_array(count, sizeof(unsigned int), GFP_KERNEL);
 		if (!txbuf) {
@@ -823,7 +827,7 @@
 	unregister_chrdev_region(lirc_base_dev, RC_DEV_MAX);
 }
 
-struct rc_dev *rc_dev_get_from_fd(int fd)
+struct rc_dev *rc_dev_get_from_fd(int fd, bool write)
 {
 	struct fd f = fdget(fd);
 	struct lirc_fh *fh;
@@ -837,6 +841,11 @@
 		return ERR_PTR(-EINVAL);
 	}
 
+	if (write && !(f.file->f_mode & FMODE_WRITE)) {
+		fdput(f);
+		return ERR_PTR(-EPERM);
+	}
+
 	fh = f.file->private_data;
 	dev = fh->rc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/mceusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/mceusb.c
@@ -1077,7 +1077,7 @@
 	struct mceusb_dev *ir = dev->priv;
 	unsigned int units;
 
-	units = DIV_ROUND_CLOSEST(timeout, MCE_TIME_UNIT);
+	units = DIV_ROUND_UP(timeout, MCE_TIME_UNIT);
 
 	cmdbuf[2] = units >> 8;
 	cmdbuf[3] = units;
@@ -1386,6 +1386,7 @@
 	case -ECONNRESET:
 	case -ENOENT:
 	case -EILSEQ:
+	case -EPROTO:
 	case -ESHUTDOWN:
 		usb_unlink_urb(urb);
 		return;
@@ -1415,42 +1416,37 @@
 {
 	int ret;
 	struct device *dev = ir->dev;
-	char *data;
-
-	data = kzalloc(USB_CTRL_MSG_SZ, GFP_KERNEL);
-	if (!data) {
-		dev_err(dev, "%s: memory allocation failed!", __func__);
-		return;
-	}
+	char data[USB_CTRL_MSG_SZ];
 
 	/*
 	 * This is a strange one. Windows issues a set address to the device
 	 * on the receive control pipe and expect a certain value pair back
 	 */
-	ret = usb_control_msg(ir->usbdev, usb_rcvctrlpipe(ir->usbdev, 0),
-			      USB_REQ_SET_ADDRESS, USB_TYPE_VENDOR, 0, 0,
-			      data, USB_CTRL_MSG_SZ, HZ * 3);
+	ret = usb_control_msg_recv(ir->usbdev, 0, USB_REQ_SET_ADDRESS,
+				   USB_DIR_IN | USB_TYPE_VENDOR,
+				   0, 0, data, USB_CTRL_MSG_SZ, 3000,
+				   GFP_KERNEL);
 	dev_dbg(dev, "set address - ret = %d", ret);
 	dev_dbg(dev, "set address - data[0] = %d, data[1] = %d",
 						data[0], data[1]);
 
 	/* set feature: bit rate 38400 bps */
-	ret = usb_control_msg(ir->usbdev, usb_sndctrlpipe(ir->usbdev, 0),
-			      USB_REQ_SET_FEATURE, USB_TYPE_VENDOR,
-			      0xc04e, 0x0000, NULL, 0, HZ * 3);
+	ret = usb_control_msg_send(ir->usbdev, 0,
+				   USB_REQ_SET_FEATURE, USB_TYPE_VENDOR,
+				   0xc04e, 0x0000, NULL, 0, 3000, GFP_KERNEL);
 
 	dev_dbg(dev, "set feature - ret = %d", ret);
 
 	/* bRequest 4: set char length to 8 bits */
-	ret = usb_control_msg(ir->usbdev, usb_sndctrlpipe(ir->usbdev, 0),
-			      4, USB_TYPE_VENDOR,
-			      0x0808, 0x0000, NULL, 0, HZ * 3);
+	ret = usb_control_msg_send(ir->usbdev, 0,
+				   4, USB_TYPE_VENDOR,
+				   0x0808, 0x0000, NULL, 0, 3000, GFP_KERNEL);
 	dev_dbg(dev, "set char length - retB = %d", ret);
 
 	/* bRequest 2: set handshaking to use DTR/DSR */
-	ret = usb_control_msg(ir->usbdev, usb_sndctrlpipe(ir->usbdev, 0),
-			      2, USB_TYPE_VENDOR,
-			      0x0000, 0x0100, NULL, 0, HZ * 3);
+	ret = usb_control_msg_send(ir->usbdev, 0,
+				   2, USB_TYPE_VENDOR,
+				   0x0000, 0x0100, NULL, 0, 3000, GFP_KERNEL);
 	dev_dbg(dev, "set handshake  - retC = %d", ret);
 
 	/* device resume */
@@ -1458,8 +1454,6 @@
 
 	/* get hw/sw revision? */
 	mce_command_out(ir, GET_REVISION, sizeof(GET_REVISION));
-
-	kfree(data);
 }
 
 static void mceusb_gen2_init(struct mceusb_dev *ir)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/rc-core-priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/rc-core-priv.h
@@ -325,7 +325,7 @@
 void lirc_scancode_event(struct rc_dev *dev, struct lirc_scancode *lsc);
 int lirc_register(struct rc_dev *dev);
 void lirc_unregister(struct rc_dev *dev);
-struct rc_dev *rc_dev_get_from_fd(int fd);
+struct rc_dev *rc_dev_get_from_fd(int fd, bool write);
 #else
 static inline int lirc_dev_init(void) { return 0; }
 static inline void lirc_dev_exit(void) {}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/rc/redrat3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/rc/redrat3.c
@@ -404,7 +404,7 @@
 	udev = rr3->udev;
 	res = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), cmd,
 			      USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-			      0x0000, 0x0000, data, sizeof(u8), HZ * 10);
+			      0x0000, 0x0000, data, sizeof(u8), 10000);
 
 	if (res < 0) {
 		dev_err(rr3->dev, "%s: Error sending rr3 cmd res %d, data %d",
@@ -480,7 +480,7 @@
 	pipe = usb_rcvctrlpipe(rr3->udev, 0);
 	ret = usb_control_msg(rr3->udev, pipe, RR3_GET_IR_PARAM,
 			      USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-			      RR3_IR_IO_SIG_TIMEOUT, 0, tmp, len, HZ * 5);
+			      RR3_IR_IO_SIG_TIMEOUT, 0, tmp, len, 5000);
 	if (ret != len)
 		dev_warn(rr3->dev, "Failed to read timeout from hardware\n");
 	else {
@@ -510,7 +510,7 @@
 	ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), RR3_SET_IR_PARAM,
 		     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
 		     RR3_IR_IO_SIG_TIMEOUT, 0, timeout, sizeof(*timeout),
-		     HZ * 25);
+		     25000);
 	dev_dbg(dev, "set ir parm timeout %d ret 0x%02x\n",
 						be32_to_cpu(*timeout), ret);
 
@@ -542,32 +542,32 @@
 	*val = 0x01;
 	rc = usb_control_msg(udev, rxpipe, RR3_RESET,
 			     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-			     RR3_CPUCS_REG_ADDR, 0, val, len, HZ * 25);
+			     RR3_CPUCS_REG_ADDR, 0, val, len, 25000);
 	dev_dbg(dev, "reset returned 0x%02x\n", rc);
 
 	*val = length_fuzz;
 	rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
 			     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
-			     RR3_IR_IO_LENGTH_FUZZ, 0, val, len, HZ * 25);
+			     RR3_IR_IO_LENGTH_FUZZ, 0, val, len, 25000);
 	dev_dbg(dev, "set ir parm len fuzz %d rc 0x%02x\n", *val, rc);
 
 	*val = (65536 - (minimum_pause * 2000)) / 256;
 	rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
 			     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
-			     RR3_IR_IO_MIN_PAUSE, 0, val, len, HZ * 25);
+			     RR3_IR_IO_MIN_PAUSE, 0, val, len, 25000);
 	dev_dbg(dev, "set ir parm min pause %d rc 0x%02x\n", *val, rc);
 
 	*val = periods_measure_carrier;
 	rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
 			     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
-			     RR3_IR_IO_PERIODS_MF, 0, val, len, HZ * 25);
+			     RR3_IR_IO_PERIODS_MF, 0, val, len, 25000);
 	dev_dbg(dev, "set ir parm periods measure carrier %d rc 0x%02x", *val,
 									rc);
 
 	*val = RR3_DRIVER_MAXLENS;
 	rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
 			     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
-			     RR3_IR_IO_MAX_LENGTHS, 0, val, len, HZ * 25);
+			     RR3_IR_IO_MAX_LENGTHS, 0, val, len, 25000);
 	dev_dbg(dev, "set ir parm max lens %d rc 0x%02x\n", *val, rc);
 
 	kfree(val);
@@ -585,7 +585,7 @@
 	rc = usb_control_msg(rr3->udev, usb_rcvctrlpipe(rr3->udev, 0),
 			     RR3_FW_VERSION,
 			     USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-			     0, 0, buffer, RR3_FW_VERSION_LEN, HZ * 5);
+			     0, 0, buffer, RR3_FW_VERSION_LEN, 5000);
 
 	if (rc >= 0)
 		dev_info(rr3->dev, "Firmware rev: %s", buffer);
@@ -825,14 +825,14 @@
 
 	pipe = usb_sndbulkpipe(rr3->udev, rr3->ep_out->bEndpointAddress);
 	ret = usb_bulk_msg(rr3->udev, pipe, irdata,
-			    sendbuf_len, &ret_len, 10 * HZ);
+			    sendbuf_len, &ret_len, 10000);
 	dev_dbg(dev, "sent %d bytes, (ret %d)\n", ret_len, ret);
 
 	/* now tell the hardware to transmit what we sent it */
 	pipe = usb_rcvctrlpipe(rr3->udev, 0);
 	ret = usb_control_msg(rr3->udev, pipe, RR3_TX_SEND_SIGNAL,
 			      USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-			      0, 0, irdata, 2, HZ * 10);
+			      0, 0, irdata, 2, 10000);
 
 	if (ret < 0)
 		dev_err(dev, "Error: control msg send failed, rc %d\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/spi/cxd2880-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/spi/cxd2880-spi.c
@@ -618,7 +618,7 @@
 fail_attach:
 	dvb_unregister_adapter(&dvb_spi->adapter);
 fail_adapter:
-	if (!dvb_spi->vcc_supply)
+	if (dvb_spi->vcc_supply)
 		regulator_disable(dvb_spi->vcc_supply);
 fail_regulator:
 	kfree(dvb_spi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vidtv/vidtv_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vidtv/vidtv_bridge.c
@@ -191,10 +191,11 @@
 
 	mux_args.mux_buf_sz  = mux_buf_sz;
 
-	dvb->streaming = true;
 	dvb->mux = vidtv_mux_init(dvb->fe[0], dev, &mux_args);
 	if (!dvb->mux)
 		return -ENOMEM;
+
+	dvb->streaming = true;
 	vidtv_mux_start_thread(dvb->mux);
 
 	dev_dbg_ratelimited(dev, "Started streaming\n");
@@ -205,6 +206,11 @@
 {
 	struct device *dev = &dvb->pdev->dev;
 
+	if (!dvb->streaming) {
+		dev_warn_ratelimited(dev, "No streaming. Skipping.\n");
+		return 0;
+	}
+
 	dvb->streaming = false;
 	vidtv_mux_stop_thread(dvb->mux);
 	vidtv_mux_destroy(dvb->mux);
@@ -459,26 +465,20 @@
 	for (j = j - 1; j >= 0; --j)
 		dvb->demux.dmx.remove_frontend(&dvb->demux.dmx,
 					       &dvb->dmx_fe[j]);
-fail_dmx_dev:
 	dvb_dmxdev_release(&dvb->dmx_dev);
-fail_dmx:
+fail_dmx_dev:
 	dvb_dmx_release(&dvb->demux);
+fail_dmx:
+fail_demod_probe:
+	for (i = i - 1; i >= 0; --i) {
+		dvb_unregister_frontend(dvb->fe[i]);
 fail_fe:
-	for (j = i; j >= 0; --j)
-		dvb_unregister_frontend(dvb->fe[j]);
+		dvb_module_release(dvb->i2c_client_tuner[i]);
 fail_tuner_probe:
-	for (j = i; j >= 0; --j)
-		if (dvb->i2c_client_tuner[j])
-			dvb_module_release(dvb->i2c_client_tuner[j]);
-
-fail_demod_probe:
-	for (j = i; j >= 0; --j)
-		if (dvb->i2c_client_demod[j])
-			dvb_module_release(dvb->i2c_client_demod[j]);
-
+		dvb_module_release(dvb->i2c_client_demod[i]);
+	}
 fail_adapter:
 	dvb_unregister_adapter(&dvb->adapter);
-
 fail_i2c:
 	i2c_del_adapter(&dvb->i2c_adapter);
 
@@ -564,6 +564,10 @@
 
 static void vidtv_bridge_dev_release(struct device *dev)
 {
+	struct vidtv_dvb *dvb;
+
+	dvb = dev_get_drvdata(dev);
+	kfree(dvb);
 }
 
 static struct platform_device vidtv_bridge_dev = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vidtv/vidtv_mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vidtv/vidtv_mux.c
@@ -504,13 +504,16 @@
 	m->priv = args->priv;
 	m->network_id = args->network_id;
 	m->network_name = kstrdup(args->network_name, GFP_KERNEL);
+	if (!m->network_name)
+		goto free_mux_buf;
+
 	m->timing.current_jiffies = get_jiffies_64();
 
 	if (args->channels)
 		m->channels = args->channels;
 	else
 		if (vidtv_channels_init(m) < 0)
-			goto free_mux_buf;
+			goto free_mux_network_name;
 
 	/* will alloc data for pmt_sections after initializing pat */
 	if (vidtv_channel_si_init(m) < 0)
@@ -527,6 +530,8 @@
 	vidtv_channel_si_destroy(m);
 free_channels:
 	vidtv_channels_destroy(m);
+free_mux_network_name:
+	kfree(m->network_name);
 free_mux_buf:
 	vfree(m->mux_buf);
 free_mux:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vidtv/vidtv_psi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vidtv/vidtv_psi.c
@@ -307,16 +307,29 @@
 
 	desc->service_name_len = service_name_len;
 
-	if (service_name && service_name_len)
+	if (service_name && service_name_len) {
 		desc->service_name = kstrdup(service_name, GFP_KERNEL);
+		if (!desc->service_name)
+			goto free_desc;
+	}
 
 	desc->provider_name_len = provider_name_len;
 
-	if (provider_name && provider_name_len)
+	if (provider_name && provider_name_len) {
 		desc->provider_name = kstrdup(provider_name, GFP_KERNEL);
+		if (!desc->provider_name)
+			goto free_desc_service_name;
+	}
 
 	vidtv_psi_desc_chain(head, (struct vidtv_psi_desc *)desc);
 	return desc;
+
+free_desc_service_name:
+	if (service_name && service_name_len)
+		kfree(desc->service_name);
+free_desc:
+	kfree(desc);
+	return NULL;
 }
 
 struct vidtv_psi_desc_registration
@@ -361,8 +374,13 @@
 
 	desc->length = network_name_len;
 
-	if (network_name && network_name_len)
+	if (network_name && network_name_len) {
 		desc->network_name = kstrdup(network_name, GFP_KERNEL);
+		if (!desc->network_name) {
+			kfree(desc);
+			return NULL;
+		}
+	}
 
 	vidtv_psi_desc_chain(head, (struct vidtv_psi_desc *)desc);
 	return desc;
@@ -448,15 +466,32 @@
 		iso_language_code = "eng";
 
 	desc->iso_language_code = kstrdup(iso_language_code, GFP_KERNEL);
+	if (!desc->iso_language_code)
+		goto free_desc;
 
-	if (event_name && event_name_len)
+	if (event_name && event_name_len) {
 		desc->event_name = kstrdup(event_name, GFP_KERNEL);
+		if (!desc->event_name)
+			goto free_desc_language_code;
+	}
 
-	if (text && text_len)
+	if (text && text_len) {
 		desc->text = kstrdup(text, GFP_KERNEL);
+		if (!desc->text)
+			goto free_desc_event_name;
+	}
 
 	vidtv_psi_desc_chain(head, (struct vidtv_psi_desc *)desc);
 	return desc;
+
+free_desc_event_name:
+	if (event_name && event_name_len)
+		kfree(desc->event_name);
+free_desc_language_code:
+	kfree(desc->iso_language_code);
+free_desc:
+	kfree(desc);
+	return NULL;
 }
 
 struct vidtv_psi_desc *vidtv_psi_desc_clone(struct vidtv_psi_desc *desc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vidtv/vidtv_s302m.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vidtv/vidtv_s302m.c
@@ -455,6 +455,9 @@
 		e->name = kstrdup(args.name, GFP_KERNEL);
 
 	e->encoder_buf = vzalloc(VIDTV_S302M_BUF_SZ);
+	if (!e->encoder_buf)
+		goto out_kfree_e;
+
 	e->encoder_buf_sz = VIDTV_S302M_BUF_SZ;
 	e->encoder_buf_offset = 0;
 
@@ -467,10 +470,8 @@
 	e->is_video_encoder = false;
 
 	ctx = kzalloc(priv_sz, GFP_KERNEL);
-	if (!ctx) {
-		kfree(e);
-		return NULL;
-	}
+	if (!ctx)
+		goto out_kfree_buf;
 
 	e->ctx = ctx;
 	ctx->last_duration = 0;
@@ -498,6 +499,14 @@
 	e->next = NULL;
 
 	return e;
+
+out_kfree_buf:
+	kfree(e->encoder_buf);
+
+out_kfree_e:
+	kfree(e->name);
+	kfree(e);
+	return NULL;
 }
 
 void vidtv_s302m_encoder_destroy(struct vidtv_encoder *e)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vimc/vimc-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vimc/vimc-core.c
@@ -357,7 +357,7 @@
 	if (ret) {
 		dev_err(&vimc_pdev.dev,
 			"platform driver registration failed (err=%d)\n", ret);
-		platform_driver_unregister(&vimc_pdrv);
+		platform_device_unregister(&vimc_pdev);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vivid/vivid-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vivid/vivid-core.c
@@ -330,6 +330,28 @@
 	return vivid_vid_out_g_fbuf(file, fh, a);
 }
 
+/*
+ * Only support the framebuffer of one of the vivid instances.
+ * Anything else is rejected.
+ */
+bool vivid_validate_fb(const struct v4l2_framebuffer *a)
+{
+	struct vivid_dev *dev;
+	int i;
+
+	for (i = 0; i < n_devs; i++) {
+		dev = vivid_devs[i];
+		if (!dev || !dev->video_pbase)
+			continue;
+		if ((unsigned long)a->base == dev->video_pbase &&
+		    a->fmt.width <= dev->display_width &&
+		    a->fmt.height <= dev->display_height &&
+		    a->fmt.bytesperline <= dev->display_byte_stride)
+			return true;
+	}
+	return false;
+}
+
 static int vidioc_s_fbuf(struct file *file, void *fh, const struct v4l2_framebuffer *a)
 {
 	struct video_device *vdev = video_devdata(file);
@@ -910,8 +932,12 @@
 
 	/* how many inputs do we have and of what type? */
 	dev->num_inputs = num_inputs[inst];
-	if (dev->num_inputs < 1)
-		dev->num_inputs = 1;
+	if (node_type & 0x20007) {
+		if (dev->num_inputs < 1)
+			dev->num_inputs = 1;
+	} else {
+		dev->num_inputs = 0;
+	}
 	if (dev->num_inputs >= MAX_INPUTS)
 		dev->num_inputs = MAX_INPUTS;
 	for (i = 0; i < dev->num_inputs; i++) {
@@ -928,8 +954,12 @@
 
 	/* how many outputs do we have and of what type? */
 	dev->num_outputs = num_outputs[inst];
-	if (dev->num_outputs < 1)
-		dev->num_outputs = 1;
+	if (node_type & 0x40300) {
+		if (dev->num_outputs < 1)
+			dev->num_outputs = 1;
+	} else {
+		dev->num_outputs = 0;
+	}
 	if (dev->num_outputs >= MAX_OUTPUTS)
 		dev->num_outputs = MAX_OUTPUTS;
 	for (i = 0; i < dev->num_outputs; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vivid/vivid-core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vivid/vivid-core.h
@@ -610,4 +610,6 @@
 	return dev->output_type[dev->output] == HDMI;
 }
 
+bool vivid_validate_fb(const struct v4l2_framebuffer *a);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vivid/vivid-rds-gen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vivid/vivid-rds-gen.c
@@ -145,7 +145,7 @@
 	rds->ta = alt;
 	rds->ms = true;
 	snprintf(rds->psname, sizeof(rds->psname), "%6d.%1d",
-		 freq / 16, ((freq & 0xf) * 10) / 16);
+		 (freq / 16) % 1000000, (((freq & 0xf) * 10) / 16) % 10);
 	if (alt)
 		strscpy(rds->radiotext,
 			" The Radio Data System can switch between different Radio Texts ",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vivid/vivid-vid-cap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vivid/vivid-vid-cap.c
@@ -113,8 +113,9 @@
 		if (*nplanes != buffers)
 			return -EINVAL;
 		for (p = 0; p < buffers; p++) {
-			if (sizes[p] < tpg_g_line_width(&dev->tpg, p) * h +
-						dev->fmt_cap->data_offset[p])
+			if (sizes[p] < tpg_g_line_width(&dev->tpg, p) * h /
+					dev->fmt_cap->vdownsampling[p] +
+					dev->fmt_cap->data_offset[p])
 				return -EINVAL;
 		}
 	} else {
@@ -452,6 +453,12 @@
 	tpg_reset_source(&dev->tpg, dev->src_rect.width, dev->src_rect.height, dev->field_cap);
 	dev->crop_cap = dev->src_rect;
 	dev->crop_bounds_cap = dev->src_rect;
+	if (dev->bitmap_cap &&
+	    (dev->compose_cap.width != dev->crop_cap.width ||
+	     dev->compose_cap.height != dev->crop_cap.height)) {
+		vfree(dev->bitmap_cap);
+		dev->bitmap_cap = NULL;
+	}
 	dev->compose_cap = dev->crop_cap;
 	if (V4L2_FIELD_HAS_T_OR_B(dev->field_cap))
 		dev->compose_cap.height /= 2;
@@ -909,6 +916,8 @@
 	struct vivid_dev *dev = video_drvdata(file);
 	struct v4l2_rect *crop = &dev->crop_cap;
 	struct v4l2_rect *compose = &dev->compose_cap;
+	unsigned orig_compose_w = compose->width;
+	unsigned orig_compose_h = compose->height;
 	unsigned factor = V4L2_FIELD_HAS_T_OR_B(dev->field_cap) ? 2 : 1;
 	int ret;
 
@@ -953,6 +962,7 @@
 			if (dev->has_compose_cap) {
 				v4l2_rect_set_min_size(compose, &min_rect);
 				v4l2_rect_set_max_size(compose, &max_rect);
+				v4l2_rect_map_inside(compose, &fmt);
 			}
 			dev->fmt_cap_rect = fmt;
 			tpg_s_buf_height(&dev->tpg, fmt.height);
@@ -1025,17 +1035,17 @@
 			s->r.height /= factor;
 		}
 		v4l2_rect_map_inside(&s->r, &dev->fmt_cap_rect);
-		if (dev->bitmap_cap && (compose->width != s->r.width ||
-					compose->height != s->r.height)) {
-			vfree(dev->bitmap_cap);
-			dev->bitmap_cap = NULL;
-		}
 		*compose = s->r;
 		break;
 	default:
 		return -EINVAL;
 	}
 
+	if (dev->bitmap_cap && (compose->width != orig_compose_w ||
+				compose->height != orig_compose_h)) {
+		vfree(dev->bitmap_cap);
+		dev->bitmap_cap = NULL;
+	}
 	tpg_s_crop_compose(&dev->tpg, crop, compose);
 	return 0;
 }
@@ -1272,7 +1282,14 @@
 		return -EINVAL;
 	if (a->fmt.bytesperline < (a->fmt.width * fmt->bit_depth[0]) / 8)
 		return -EINVAL;
-	if (a->fmt.height * a->fmt.bytesperline < a->fmt.sizeimage)
+	if (a->fmt.bytesperline > a->fmt.sizeimage / a->fmt.height)
+		return -EINVAL;
+
+	/*
+	 * Only support the framebuffer of one of the vivid instances.
+	 * Anything else is rejected.
+	 */
+	if (!vivid_validate_fb(a))
 		return -EINVAL;
 
 	dev->fb_vbase_cap = phys_to_virt((unsigned long)a->base);
@@ -1690,12 +1707,19 @@
 	h_freq = (u32)bt->pixelclock / total_h_pixel;
 
 	if (bt->standards == 0 || (bt->standards & V4L2_DV_BT_STD_CVT)) {
+		struct v4l2_dv_timings cvt = {};
+
 		if (v4l2_detect_cvt(total_v_lines, h_freq, bt->vsync, bt->width,
-				    bt->polarities, bt->interlaced, timings))
+				    bt->polarities, bt->interlaced,
+				    &vivid_dv_timings_cap, &cvt) &&
+		    cvt.bt.width == bt->width && cvt.bt.height == bt->height) {
+			*timings = cvt;
 			return true;
+		}
 	}
 
 	if (bt->standards == 0 || (bt->standards & V4L2_DV_BT_STD_GTF)) {
+		struct v4l2_dv_timings gtf = {};
 		struct v4l2_fract aspect_ratio;
 
 		find_aspect_ratio(bt->width, bt->height,
@@ -1703,8 +1727,12 @@
 				  &aspect_ratio.denominator);
 		if (v4l2_detect_gtf(total_v_lines, h_freq, bt->vsync,
 				    bt->polarities, bt->interlaced,
-				    aspect_ratio, timings))
+				    aspect_ratio, &vivid_dv_timings_cap,
+				    &gtf) &&
+		    gtf.bt.width == bt->width && gtf.bt.height == bt->height) {
+			*timings = gtf;
 			return true;
+		}
 	}
 	return false;
 }
@@ -1781,8 +1809,10 @@
 		return -EINVAL;
 	if (edid->blocks == 0) {
 		dev->edid_blocks = 0;
-		v4l2_ctrl_s_ctrl(dev->ctrl_tx_edid_present, 0);
-		v4l2_ctrl_s_ctrl(dev->ctrl_tx_hotplug, 0);
+		if (dev->num_outputs) {
+			v4l2_ctrl_s_ctrl(dev->ctrl_tx_edid_present, 0);
+			v4l2_ctrl_s_ctrl(dev->ctrl_tx_hotplug, 0);
+		}
 		phys_addr = CEC_PHYS_ADDR_INVALID;
 		goto set_phys_addr;
 	}
@@ -1806,8 +1836,10 @@
 			display_present |=
 				dev->display_present[i] << j++;
 
-	v4l2_ctrl_s_ctrl(dev->ctrl_tx_edid_present, display_present);
-	v4l2_ctrl_s_ctrl(dev->ctrl_tx_hotplug, display_present);
+	if (dev->num_outputs) {
+		v4l2_ctrl_s_ctrl(dev->ctrl_tx_edid_present, display_present);
+		v4l2_ctrl_s_ctrl(dev->ctrl_tx_hotplug, display_present);
+	}
 
 set_phys_addr:
 	/* TODO: a proper hotplug detect cycle should be emulated here */
@@ -1880,7 +1912,7 @@
 			break;
 	if (i == ARRAY_SIZE(webcam_sizes))
 		return -EINVAL;
-	if (fival->index >= 2 * (VIVID_WEBCAM_SIZES - i))
+	if (fival->index >= 2 * VIVID_WEBCAM_SIZES)
 		return -EINVAL;
 	fival->type = V4L2_FRMIVAL_TYPE_DISCRETE;
 	fival->discrete = webcam_intervals[fival->index];
@@ -1907,7 +1939,7 @@
 			  struct v4l2_streamparm *parm)
 {
 	struct vivid_dev *dev = video_drvdata(file);
-	unsigned ival_sz = 2 * (VIVID_WEBCAM_SIZES - dev->webcam_size_idx);
+	unsigned ival_sz = 2 * VIVID_WEBCAM_SIZES;
 	struct v4l2_fract tpf;
 	unsigned i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vivid/vivid-vid-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vivid/vivid-vid-common.c
@@ -74,6 +74,14 @@
 		.buffers = 1,
 	},
 	{
+		.fourcc   = V4L2_PIX_FMT_YUV444P,
+		.vdownsampling = { 1, 1, 1 },
+		.bit_depth = { 8, 8, 8 },
+		.color_enc = TGP_COLOR_ENC_YCBCR,
+		.planes   = 3,
+		.buffers = 1,
+	},
+	{
 		.fourcc   = V4L2_PIX_FMT_YUV420,
 		.vdownsampling = { 1, 2, 2 },
 		.bit_depth = { 8, 4, 4 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/test-drivers/vivid/vivid-vid-out.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/test-drivers/vivid/vivid-vid-out.c
@@ -63,14 +63,16 @@
 		if (sizes[0] < size)
 			return -EINVAL;
 		for (p = 1; p < planes; p++) {
-			if (sizes[p] < dev->bytesperline_out[p] * h +
-				       vfmt->data_offset[p])
+			if (sizes[p] < dev->bytesperline_out[p] * h /
+					vfmt->vdownsampling[p] +
+					vfmt->data_offset[p])
 				return -EINVAL;
 		}
 	} else {
 		for (p = 0; p < planes; p++)
-			sizes[p] = p ? dev->bytesperline_out[p] * h +
-				       vfmt->data_offset[p] : size;
+			sizes[p] = p ? dev->bytesperline_out[p] * h /
+					vfmt->vdownsampling[p] +
+					vfmt->data_offset[p] : size;
 	}
 
 	if (vq->num_buffers + *nbuffers < 2)
@@ -127,7 +129,7 @@
 
 	for (p = 0; p < planes; p++) {
 		if (p)
-			size = dev->bytesperline_out[p] * h;
+			size = dev->bytesperline_out[p] * h / vfmt->vdownsampling[p];
 		size += vb->planes[p].data_offset;
 
 		if (vb2_get_plane_payload(vb, p) < size) {
@@ -334,8 +336,8 @@
 	for (p = 0; p < mp->num_planes; p++) {
 		mp->plane_fmt[p].bytesperline = dev->bytesperline_out[p];
 		mp->plane_fmt[p].sizeimage =
-			mp->plane_fmt[p].bytesperline * mp->height +
-			fmt->data_offset[p];
+			mp->plane_fmt[p].bytesperline * mp->height /
+			fmt->vdownsampling[p] + fmt->data_offset[p];
 	}
 	for (p = fmt->buffers; p < fmt->planes; p++) {
 		unsigned stride = dev->bytesperline_out[p];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/fc0011.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/fc0011.c
@@ -499,7 +499,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(fc0011_attach);
+EXPORT_SYMBOL_GPL(fc0011_attach);
 
 MODULE_DESCRIPTION("Fitipower FC0011 silicon tuner driver");
 MODULE_AUTHOR("Michael Buesch <m@bues.ch>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/fc0012.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/fc0012.c
@@ -495,7 +495,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(fc0012_attach);
+EXPORT_SYMBOL_GPL(fc0012_attach);
 
 MODULE_DESCRIPTION("Fitipower FC0012 silicon tuner driver");
 MODULE_AUTHOR("Hans-Frieder Vogt <hfvogt@gmx.net>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/fc0013.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/fc0013.c
@@ -608,7 +608,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(fc0013_attach);
+EXPORT_SYMBOL_GPL(fc0013_attach);
 
 MODULE_DESCRIPTION("Fitipower FC0013 silicon tuner driver");
 MODULE_AUTHOR("Hans-Frieder Vogt <hfvogt@gmx.net>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/max2165.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/max2165.c
@@ -410,7 +410,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(max2165_attach);
+EXPORT_SYMBOL_GPL(max2165_attach);
 
 MODULE_AUTHOR("David T. L. Wong <davidtlwong@gmail.com>");
 MODULE_DESCRIPTION("Maxim MAX2165 silicon tuner driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/mc44s803.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/mc44s803.c
@@ -356,7 +356,7 @@
 	kfree(priv);
 	return NULL;
 }
-EXPORT_SYMBOL(mc44s803_attach);
+EXPORT_SYMBOL_GPL(mc44s803_attach);
 
 MODULE_AUTHOR("Jochen Friedrich");
 MODULE_DESCRIPTION("Freescale MC44S803 silicon tuner driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/msi001.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/msi001.c
@@ -442,6 +442,13 @@
 			V4L2_CID_RF_TUNER_BANDWIDTH_AUTO, 0, 1, 1, 1);
 	dev->bandwidth = v4l2_ctrl_new_std(&dev->hdl, &msi001_ctrl_ops,
 			V4L2_CID_RF_TUNER_BANDWIDTH, 200000, 8000000, 1, 200000);
+	if (dev->hdl.error) {
+		ret = dev->hdl.error;
+		dev_err(&spi->dev, "Could not initialize controls\n");
+		/* control init failed, free handler */
+		goto err_ctrl_handler_free;
+	}
+
 	v4l2_ctrl_auto_cluster(2, &dev->bandwidth_auto, 0, false);
 	dev->lna_gain = v4l2_ctrl_new_std(&dev->hdl, &msi001_ctrl_ops,
 			V4L2_CID_RF_TUNER_LNA_GAIN, 0, 1, 1, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/mt2060.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/mt2060.c
@@ -440,7 +440,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(mt2060_attach);
+EXPORT_SYMBOL_GPL(mt2060_attach);
 
 static int mt2060_probe(struct i2c_client *client,
 			const struct i2c_device_id *id)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/mt2131.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/mt2131.c
@@ -274,7 +274,7 @@
 	fe->tuner_priv = priv;
 	return fe;
 }
-EXPORT_SYMBOL(mt2131_attach);
+EXPORT_SYMBOL_GPL(mt2131_attach);
 
 MODULE_AUTHOR("Steven Toth");
 MODULE_DESCRIPTION("Microtune MT2131 silicon tuner driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/mt2266.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/mt2266.c
@@ -336,7 +336,7 @@
 	mt2266_calibrate(priv);
 	return fe;
 }
-EXPORT_SYMBOL(mt2266_attach);
+EXPORT_SYMBOL_GPL(mt2266_attach);
 
 MODULE_AUTHOR("Olivier DANET");
 MODULE_DESCRIPTION("Microtune MT2266 silicon tuner driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/mxl5005s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/mxl5005s.c
@@ -4128,7 +4128,7 @@
 	fe->tuner_priv = state;
 	return fe;
 }
-EXPORT_SYMBOL(mxl5005s_attach);
+EXPORT_SYMBOL_GPL(mxl5005s_attach);
 
 MODULE_DESCRIPTION("MaxLinear MXL5005S silicon tuner driver");
 MODULE_AUTHOR("Steven Toth");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/qt1010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/qt1010.c
@@ -345,11 +345,12 @@
 			else
 				valptr = &tmpval;
 
-			BUG_ON(i >= ARRAY_SIZE(i2c_data) - 1);
-
-			err = qt1010_init_meas1(priv, i2c_data[i+1].reg,
-						i2c_data[i].reg,
-						i2c_data[i].val, valptr);
+			if (i >= ARRAY_SIZE(i2c_data) - 1)
+				err = -EIO;
+			else
+				err = qt1010_init_meas1(priv, i2c_data[i + 1].reg,
+							i2c_data[i].reg,
+							i2c_data[i].val, valptr);
 			i++;
 			break;
 		}
@@ -440,7 +441,7 @@
 	fe->tuner_priv = priv;
 	return fe;
 }
-EXPORT_SYMBOL(qt1010_attach);
+EXPORT_SYMBOL_GPL(qt1010_attach);
 
 MODULE_DESCRIPTION("Quantek QT1010 silicon tuner driver");
 MODULE_AUTHOR("Antti Palosaari <crope@iki.fi>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/si2157.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/si2157.c
@@ -90,7 +90,7 @@
 	dev_dbg(&client->dev, "\n");
 
 	/* Try to get Xtal trim property, to verify tuner still running */
-	memcpy(cmd.args, "\x15\x00\x04\x02", 4);
+	memcpy(cmd.args, "\x15\x00\x02\x04", 4);
 	cmd.wlen = 4;
 	cmd.rlen = 4;
 	ret = si2157_cmd_execute(client, &cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/tda18218.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/tda18218.c
@@ -336,7 +336,7 @@
 
 	return fe;
 }
-EXPORT_SYMBOL(tda18218_attach);
+EXPORT_SYMBOL_GPL(tda18218_attach);
 
 MODULE_DESCRIPTION("NXP TDA18218HN silicon tuner driver");
 MODULE_AUTHOR("Antti Palosaari <crope@iki.fi>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/tuner-i2c.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/tuner-i2c.h
@@ -133,10 +133,8 @@
 	}								\
 	if (0 == __ret) {						\
 		state = kzalloc(sizeof(type), GFP_KERNEL);		\
-		if (!state) {						\
-			__ret = -ENOMEM;				\
+		if (NULL == state)					\
 			goto __fail;					\
-		}							\
 		state->i2c_props.addr = i2caddr;			\
 		state->i2c_props.adap = i2cadap;			\
 		state->i2c_props.name = devname;			\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/tuner-xc2028.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/tuner-xc2028.c
@@ -1361,9 +1361,16 @@
 			     void *context)
 {
 	struct dvb_frontend *fe = context;
-	struct xc2028_data *priv = fe->tuner_priv;
+	struct xc2028_data *priv;
 	int rc;
 
+	if (!fe) {
+		pr_warn("xc2028: No frontend in %s\n", __func__);
+		return;
+	}
+
+	priv = fe->tuner_priv;
+
 	tuner_dbg("request_firmware_nowait(): %s\n", fw ? "OK" : "error");
 	if (!fw) {
 		tuner_err("Could not load firmware %s.\n", priv->fname);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/xc4000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/xc4000.c
@@ -1517,10 +1517,10 @@
 {
 	struct xc4000_priv *priv = fe->tuner_priv;
 
+	mutex_lock(&priv->lock);
 	*freq = priv->freq_hz + priv->freq_offset;
 
 	if (debug) {
-		mutex_lock(&priv->lock);
 		if ((priv->cur_fw.type
 		     & (BASE | FM | DTV6 | DTV7 | DTV78 | DTV8)) == BASE) {
 			u16	snr = 0;
@@ -1531,8 +1531,8 @@
 				return 0;
 			}
 		}
-		mutex_unlock(&priv->lock);
 	}
+	mutex_unlock(&priv->lock);
 
 	dprintk(1, "%s()\n", __func__);
 
@@ -1744,7 +1744,7 @@
 	xc4000_release(fe);
 	return NULL;
 }
-EXPORT_SYMBOL(xc4000_attach);
+EXPORT_SYMBOL_GPL(xc4000_attach);
 
 MODULE_AUTHOR("Steven Toth, Davide Ferri");
 MODULE_DESCRIPTION("Xceive xc4000 silicon tuner driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/tuners/xc5000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/tuners/xc5000.c
@@ -1460,7 +1460,7 @@
 	xc5000_release(fe);
 	return NULL;
 }
-EXPORT_SYMBOL(xc5000_attach);
+EXPORT_SYMBOL_GPL(xc5000_attach);
 
 MODULE_AUTHOR("Steven Toth");
 MODULE_DESCRIPTION("Xceive xc5000 silicon tuner driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/b2c2/flexcop-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/b2c2/flexcop-usb.c
@@ -87,7 +87,7 @@
 			0,
 			fc_usb->data,
 			sizeof(u32),
-			B2C2_WAIT_FOR_OPERATION_RDW * HZ);
+			B2C2_WAIT_FOR_OPERATION_RDW);
 
 	if (ret != sizeof(u32)) {
 		err("error while %s dword from %d (%d).", read ? "reading" :
@@ -155,7 +155,7 @@
 			wIndex,
 			fc_usb->data,
 			buflen,
-			nWaitTime * HZ);
+			nWaitTime);
 	if (ret != buflen)
 		ret = -EIO;
 
@@ -248,13 +248,13 @@
 		/* DKT 020208 - add this to support special case of DiSEqC */
 	case USB_FUNC_I2C_CHECKWRITE:
 		pipe = B2C2_USB_CTRL_PIPE_OUT;
-		nWaitTime = 2;
+		nWaitTime = 2000;
 		request_type |= USB_DIR_OUT;
 		break;
 	case USB_FUNC_I2C_READ:
 	case USB_FUNC_I2C_REPEATREAD:
 		pipe = B2C2_USB_CTRL_PIPE_IN;
-		nWaitTime = 2;
+		nWaitTime = 2000;
 		request_type |= USB_DIR_IN;
 		break;
 	default:
@@ -281,7 +281,7 @@
 			wIndex,
 			fc_usb->data,
 			buflen,
-			nWaitTime * HZ);
+			nWaitTime);
 
 	if (ret != buflen)
 		ret = -EIO;
@@ -501,17 +501,21 @@
 
 static int flexcop_usb_init(struct flexcop_usb *fc_usb)
 {
-	/* use the alternate setting with the larges buffer */
-	int ret = usb_set_interface(fc_usb->udev, 0, 1);
+	struct usb_host_interface *alt;
+	int ret;
 
+	/* use the alternate setting with the largest buffer */
+	ret = usb_set_interface(fc_usb->udev, 0, 1);
 	if (ret) {
 		err("set interface failed.");
 		return ret;
 	}
 
-	if (fc_usb->uintf->cur_altsetting->desc.bNumEndpoints < 1)
+	alt = fc_usb->uintf->cur_altsetting;
+
+	if (alt->desc.bNumEndpoints < 2)
 		return -ENODEV;
-	if (!usb_endpoint_is_isoc_in(&fc_usb->uintf->cur_altsetting->endpoint[1].desc))
+	if (!usb_endpoint_is_isoc_in(&alt->endpoint[0].desc))
 		return -ENODEV;
 
 	switch (fc_usb->udev->speed) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/b2c2/flexcop-usb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/b2c2/flexcop-usb.h
@@ -91,13 +91,13 @@
 	UTILITY_SRAM_TESTVERIFY     = 0x16,
 } flexcop_usb_utility_function_t;
 
-#define B2C2_WAIT_FOR_OPERATION_RW (1*HZ)
-#define B2C2_WAIT_FOR_OPERATION_RDW (3*HZ)
-#define B2C2_WAIT_FOR_OPERATION_WDW (1*HZ)
+#define B2C2_WAIT_FOR_OPERATION_RW 1000
+#define B2C2_WAIT_FOR_OPERATION_RDW 3000
+#define B2C2_WAIT_FOR_OPERATION_WDW 1000
 
-#define B2C2_WAIT_FOR_OPERATION_V8READ (3*HZ)
-#define B2C2_WAIT_FOR_OPERATION_V8WRITE (3*HZ)
-#define B2C2_WAIT_FOR_OPERATION_V8FLASH (3*HZ)
+#define B2C2_WAIT_FOR_OPERATION_V8READ 3000
+#define B2C2_WAIT_FOR_OPERATION_V8WRITE 3000
+#define B2C2_WAIT_FOR_OPERATION_V8FLASH 3000
 
 typedef enum {
 	V8_MEMORY_PAGE_DVB_CI = 0x20,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/cpia2/cpia2_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/cpia2/cpia2_usb.c
@@ -550,7 +550,7 @@
 			       0,	/* index */
 			       buf,	/* buffer */
 			       size,
-			       HZ);
+			       1000);
 
 	kfree(buf);
 	return ret;
@@ -582,7 +582,7 @@
 			       0,	/* index */
 			       buf,	/* buffer */
 			       size,
-			       HZ);
+			       1000);
 
 	if (ret >= 0)
 		memcpy(registers, buf, size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/cx231xx/cx231xx-cards.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/cx231xx/cx231xx-cards.c
@@ -994,6 +994,8 @@
 
 /* table of devices that work with this driver */
 struct usb_device_id cx231xx_id_table[] = {
+	{USB_DEVICE(0x1D19, 0x6108),
+	.driver_info = CX231XX_BOARD_PV_XCAPTURE_USB},
 	{USB_DEVICE(0x1D19, 0x6109),
 	.driver_info = CX231XX_BOARD_PV_XCAPTURE_USB},
 	{USB_DEVICE(0x0572, 0x5A3C),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/cx231xx/cx231xx-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/cx231xx/cx231xx-core.c
@@ -1024,6 +1024,7 @@
 	if (!dev->video_mode.isoc_ctl.urb) {
 		dev_err(dev->dev,
 			"cannot alloc memory for usb buffers\n");
+		kfree(dma_q->p_left_data);
 		return -ENOMEM;
 	}
 
@@ -1033,6 +1034,7 @@
 		dev_err(dev->dev,
 			"cannot allocate memory for usbtransfer\n");
 		kfree(dev->video_mode.isoc_ctl.urb);
+		kfree(dma_q->p_left_data);
 		return -ENOMEM;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/af9035.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/af9035.c
@@ -270,6 +270,7 @@
 	struct dvb_usb_device *d = i2c_get_adapdata(adap);
 	struct state *state = d_to_priv(d);
 	int ret;
+	u32 reg;
 
 	if (mutex_lock_interruptible(&d->i2c_mutex) < 0)
 		return -EAGAIN;
@@ -322,8 +323,12 @@
 			ret = -EOPNOTSUPP;
 		} else if ((msg[0].addr == state->af9033_i2c_addr[0]) ||
 			   (msg[0].addr == state->af9033_i2c_addr[1])) {
+			if (msg[0].len < 3 || msg[1].len < 1) {
+				ret = -EOPNOTSUPP;
+				goto unlock;
+			}
 			/* demod access via firmware interface */
-			u32 reg = msg[0].buf[0] << 16 | msg[0].buf[1] << 8 |
+			reg = msg[0].buf[0] << 16 | msg[0].buf[1] << 8 |
 					msg[0].buf[2];
 
 			if (msg[0].addr == state->af9033_i2c_addr[1])
@@ -381,17 +386,18 @@
 			ret = -EOPNOTSUPP;
 		} else if ((msg[0].addr == state->af9033_i2c_addr[0]) ||
 			   (msg[0].addr == state->af9033_i2c_addr[1])) {
+			if (msg[0].len < 3) {
+				ret = -EOPNOTSUPP;
+				goto unlock;
+			}
 			/* demod access via firmware interface */
-			u32 reg = msg[0].buf[0] << 16 | msg[0].buf[1] << 8 |
+			reg = msg[0].buf[0] << 16 | msg[0].buf[1] << 8 |
 					msg[0].buf[2];
 
 			if (msg[0].addr == state->af9033_i2c_addr[1])
 				reg |= 0x100000;
 
-			ret = (msg[0].len >= 3) ? af9035_wr_regs(d, reg,
-							         &msg[0].buf[3],
-							         msg[0].len - 3)
-					        : -EOPNOTSUPP;
+			ret = af9035_wr_regs(d, reg, &msg[0].buf[3], msg[0].len - 3);
 		} else {
 			/* I2C write */
 			u8 buf[MAX_XFER_SIZE];
@@ -458,6 +464,7 @@
 		ret = -EOPNOTSUPP;
 	}
 
+unlock:
 	mutex_unlock(&d->i2c_mutex);
 
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/anysee.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/anysee.c
@@ -202,7 +202,7 @@
 
 	while (i < num) {
 		if (num > i + 1 && (msg[i+1].flags & I2C_M_RD)) {
-			if (msg[i].len > 2 || msg[i+1].len > 60) {
+			if (msg[i].len != 2 || msg[i + 1].len > 60) {
 				ret = -EOPNOTSUPP;
 				break;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/az6007.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/az6007.c
@@ -202,7 +202,8 @@
 	unsigned code;
 	enum rc_proto proto;
 
-	az6007_read(d, AZ6007_READ_IR, 0, 0, st->data, 10);
+	if (az6007_read(d, AZ6007_READ_IR, 0, 0, st->data, 10) < 0)
+		return -EIO;
 
 	if (st->data[1] == 0x44)
 		return 0;
@@ -787,6 +788,10 @@
 			if (az6007_xfer_debug)
 				printk(KERN_DEBUG "az6007: I2C W addr=0x%x len=%d\n",
 				       addr, msgs[i].len);
+			if (msgs[i].len < 1) {
+				ret = -EIO;
+				goto err;
+			}
 			req = AZ6007_I2C_WR;
 			index = msgs[i].buf[0];
 			value = addr | (1 << 8);
@@ -801,6 +806,10 @@
 			if (az6007_xfer_debug)
 				printk(KERN_DEBUG "az6007: I2C R addr=0x%x len=%d\n",
 				       addr, msgs[i].len);
+			if (msgs[i].len < 1) {
+				ret = -EIO;
+				goto err;
+			}
 			req = AZ6007_I2C_RD;
 			index = msgs[i].buf[0];
 			value = addr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/ce6230.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/ce6230.c
@@ -101,6 +101,10 @@
 		if (num > i + 1 && (msg[i+1].flags & I2C_M_RD)) {
 			if (msg[i].addr ==
 				ce6230_zl10353_config.demod_address) {
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				req.cmd = DEMOD_READ;
 				req.value = msg[i].addr >> 1;
 				req.index = msg[i].buf[0];
@@ -117,6 +121,10 @@
 		} else {
 			if (msg[i].addr ==
 				ce6230_zl10353_config.demod_address) {
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				req.cmd = DEMOD_WRITE;
 				req.value = msg[i].addr >> 1;
 				req.index = msg[i].buf[0];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/ec168.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/ec168.c
@@ -115,6 +115,10 @@
 	while (i < num) {
 		if (num > i + 1 && (msg[i+1].flags & I2C_M_RD)) {
 			if (msg[i].addr == ec168_ec100_config.demod_address) {
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				req.cmd = READ_DEMOD;
 				req.value = 0;
 				req.index = 0xff00 + msg[i].buf[0]; /* reg */
@@ -131,6 +135,10 @@
 			}
 		} else {
 			if (msg[i].addr == ec168_ec100_config.demod_address) {
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				req.cmd = WRITE_DEMOD;
 				req.value = msg[i].buf[1]; /* val */
 				req.index = 0xff00 + msg[i].buf[0]; /* reg */
@@ -139,6 +147,10 @@
 				ret = ec168_ctrl_msg(d, &req);
 				i += 1;
 			} else {
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				req.cmd = WRITE_I2C;
 				req.value = msg[i].buf[0]; /* val */
 				req.index = 0x0100 + msg[i].addr; /* I2C addr */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/gl861.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/gl861.c
@@ -120,7 +120,7 @@
 	} else if (num == 2 && !(msg[0].flags & I2C_M_RD) &&
 		   (msg[1].flags & I2C_M_RD)) {
 		/* I2C write + read */
-		if (msg[0].len > 1 || msg[1].len > sizeof(ctx->buf)) {
+		if (msg[0].len != 1 || msg[1].len > sizeof(ctx->buf)) {
 			ret = -EOPNOTSUPP;
 			goto err;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/lmedm04.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/lmedm04.c
@@ -373,6 +373,7 @@
 	struct dvb_usb_device *d = adap_to_d(adap);
 	struct lme2510_state *lme_int = adap_to_priv(adap);
 	struct usb_host_endpoint *ep;
+	int ret;
 
 	lme_int->lme_urb = usb_alloc_urb(0, GFP_KERNEL);
 
@@ -390,11 +391,20 @@
 
 	/* Quirk of pipe reporting PIPE_BULK but behaves as interrupt */
 	ep = usb_pipe_endpoint(d->udev, lme_int->lme_urb->pipe);
+	if (!ep) {
+		usb_free_urb(lme_int->lme_urb);
+		return -ENODEV;
+	}
 
 	if (usb_endpoint_type(&ep->desc) == USB_ENDPOINT_XFER_BULK)
 		lme_int->lme_urb->pipe = usb_rcvbulkpipe(d->udev, 0xa);
 
-	usb_submit_urb(lme_int->lme_urb, GFP_KERNEL);
+	ret = usb_submit_urb(lme_int->lme_urb, GFP_KERNEL);
+	if (ret) {
+		usb_free_urb(lme_int->lme_urb);
+		return ret;
+	}
+
 	info("INT Interrupt Service Started");
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/mxl111sf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/mxl111sf.c
@@ -931,8 +931,6 @@
 		  .len = sizeof(eeprom), .buf = eeprom },
 	};
 
-	mutex_init(&state->msg_lock);
-
 	ret = get_chip_info(state);
 	if (mxl_fail(ret))
 		pr_err("failed to get chip info during probe");
@@ -1074,6 +1072,14 @@
 	return 0;
 }
 
+static int mxl111sf_probe(struct dvb_usb_device *dev)
+{
+	struct mxl111sf_state *state = d_to_priv(dev);
+
+	mutex_init(&state->msg_lock);
+	return 0;
+}
+
 static struct dvb_usb_device_properties mxl111sf_props_dvbt = {
 	.driver_name = KBUILD_MODNAME,
 	.owner = THIS_MODULE,
@@ -1083,6 +1089,7 @@
 	.generic_bulk_ctrl_endpoint = 0x02,
 	.generic_bulk_ctrl_endpoint_response = 0x81,
 
+	.probe             = mxl111sf_probe,
 	.i2c_algo          = &mxl111sf_i2c_algo,
 	.frontend_attach   = mxl111sf_frontend_attach_dvbt,
 	.tuner_attach      = mxl111sf_attach_tuner,
@@ -1124,6 +1131,7 @@
 	.generic_bulk_ctrl_endpoint = 0x02,
 	.generic_bulk_ctrl_endpoint_response = 0x81,
 
+	.probe             = mxl111sf_probe,
 	.i2c_algo          = &mxl111sf_i2c_algo,
 	.frontend_attach   = mxl111sf_frontend_attach_atsc,
 	.tuner_attach      = mxl111sf_attach_tuner,
@@ -1165,6 +1173,7 @@
 	.generic_bulk_ctrl_endpoint = 0x02,
 	.generic_bulk_ctrl_endpoint_response = 0x81,
 
+	.probe             = mxl111sf_probe,
 	.i2c_algo          = &mxl111sf_i2c_algo,
 	.frontend_attach   = mxl111sf_frontend_attach_mh,
 	.tuner_attach      = mxl111sf_attach_tuner,
@@ -1233,6 +1242,7 @@
 	.generic_bulk_ctrl_endpoint = 0x02,
 	.generic_bulk_ctrl_endpoint_response = 0x81,
 
+	.probe             = mxl111sf_probe,
 	.i2c_algo          = &mxl111sf_i2c_algo,
 	.frontend_attach   = mxl111sf_frontend_attach_atsc_mh,
 	.tuner_attach      = mxl111sf_attach_tuner,
@@ -1311,6 +1321,7 @@
 	.generic_bulk_ctrl_endpoint = 0x02,
 	.generic_bulk_ctrl_endpoint_response = 0x81,
 
+	.probe             = mxl111sf_probe,
 	.i2c_algo          = &mxl111sf_i2c_algo,
 	.frontend_attach   = mxl111sf_frontend_attach_mercury,
 	.tuner_attach      = mxl111sf_attach_tuner,
@@ -1381,6 +1392,7 @@
 	.generic_bulk_ctrl_endpoint = 0x02,
 	.generic_bulk_ctrl_endpoint_response = 0x81,
 
+	.probe             = mxl111sf_probe,
 	.i2c_algo          = &mxl111sf_i2c_algo,
 	.frontend_attach   = mxl111sf_frontend_attach_mercury_mh,
 	.tuner_attach      = mxl111sf_attach_tuner,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
@@ -176,6 +176,10 @@
 			ret = -EOPNOTSUPP;
 			goto err_mutex_unlock;
 		} else if (msg[0].addr == 0x10) {
+			if (msg[0].len < 1 || msg[1].len < 1) {
+				ret = -EOPNOTSUPP;
+				goto err_mutex_unlock;
+			}
 			/* method 1 - integrated demod */
 			if (msg[0].buf[0] == 0x00) {
 				/* return demod page from driver cache */
@@ -189,6 +193,10 @@
 				ret = rtl28xxu_ctrl_msg(d, &req);
 			}
 		} else if (msg[0].len < 2) {
+			if (msg[0].len < 1) {
+				ret = -EOPNOTSUPP;
+				goto err_mutex_unlock;
+			}
 			/* method 2 - old I2C */
 			req.value = (msg[0].buf[0] << 8) | (msg[0].addr << 1);
 			req.index = CMD_I2C_RD;
@@ -217,8 +225,16 @@
 			ret = -EOPNOTSUPP;
 			goto err_mutex_unlock;
 		} else if (msg[0].addr == 0x10) {
+			if (msg[0].len < 1) {
+				ret = -EOPNOTSUPP;
+				goto err_mutex_unlock;
+			}
 			/* method 1 - integrated demod */
 			if (msg[0].buf[0] == 0x00) {
+				if (msg[0].len < 2) {
+					ret = -EOPNOTSUPP;
+					goto err_mutex_unlock;
+				}
 				/* save demod page for later demod access */
 				dev->page = msg[0].buf[1];
 				ret = 0;
@@ -231,6 +247,10 @@
 				ret = rtl28xxu_ctrl_msg(d, &req);
 			}
 		} else if ((msg[0].len < 23) && (!dev->new_i2c_write)) {
+			if (msg[0].len < 1) {
+				ret = -EOPNOTSUPP;
+				goto err_mutex_unlock;
+			}
 			/* method 2 - old I2C */
 			req.value = (msg[0].buf[0] << 8) | (msg[0].addr << 1);
 			req.index = CMD_I2C_WR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/af9005.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/af9005.c
@@ -422,6 +422,10 @@
 		if (ret == 0)
 			ret = 2;
 	} else {
+		if (msg[0].len < 2) {
+			ret = -EOPNOTSUPP;
+			goto unlock;
+		}
 		/* write one or more registers */
 		reg = msg[0].buf[0];
 		addr = msg[0].addr;
@@ -431,6 +435,7 @@
 			ret = 1;
 	}
 
+unlock:
 	mutex_unlock(&d->i2c_mutex);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/az6027.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/az6027.c
@@ -391,6 +391,7 @@
 /* remote control stuff (does not work with my box) */
 static int az6027_rc_query(struct dvb_usb_device *d, u32 *event, int *state)
 {
+	*state = REMOTE_NO_KEY_PRESSED;
 	return 0;
 }
 
@@ -974,6 +975,10 @@
 		if (msg[i].addr == 0x99) {
 			req = 0xBE;
 			index = 0;
+			if (msg[i].len < 1) {
+				i = -EOPNOTSUPP;
+				break;
+			}
 			value = msg[i].buf[0] & 0x00ff;
 			length = 1;
 			az6027_usb_out_op(d, req, value, index, data, length);
@@ -983,6 +988,10 @@
 			/* write/read request */
 			if (i + 1 < num && (msg[i + 1].flags & I2C_M_RD)) {
 				req = 0xB9;
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				index = (((msg[i].buf[0] << 8) & 0xff00) | (msg[i].buf[1] & 0x00ff));
 				value = msg[i].addr + (msg[i].len << 8);
 				length = msg[i + 1].len + 6;
@@ -996,6 +1005,10 @@
 
 				/* demod 16bit addr */
 				req = 0xBD;
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				index = (((msg[i].buf[0] << 8) & 0xff00) | (msg[i].buf[1] & 0x00ff));
 				value = msg[i].addr + (2 << 8);
 				length = msg[i].len - 2;
@@ -1021,6 +1034,10 @@
 			} else {
 
 				req = 0xBD;
+				if (msg[i].len < 1) {
+					i = -EOPNOTSUPP;
+					break;
+				}
 				index = msg[i].buf[0] & 0x00FF;
 				value = msg[i].addr + (1 << 8);
 				length = msg[i].len - 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/cxusb-analog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/cxusb-analog.c
@@ -1014,7 +1014,10 @@
 {
 	struct dvb_usb_device *dvbdev = video_drvdata(file);
 	struct cxusb_medion_dev *cxdev = dvbdev->priv;
-	struct v4l2_subdev_format subfmt;
+	struct v4l2_subdev_format subfmt = {
+		.which = isset ? V4L2_SUBDEV_FORMAT_ACTIVE :
+			 V4L2_SUBDEV_FORMAT_TRY,
+	};
 	u32 field;
 	int ret;
 
@@ -1024,9 +1027,6 @@
 	field = vb2_start_streaming_called(&cxdev->videoqueue) ?
 		cxdev->field_order : cxusb_medion_field_order(cxdev);
 
-	memset(&subfmt, 0, sizeof(subfmt));
-	subfmt.which = isset ? V4L2_SUBDEV_FORMAT_ACTIVE :
-		V4L2_SUBDEV_FORMAT_TRY;
 	subfmt.format.width = f->fmt.pix.width & ~1;
 	subfmt.format.height = f->fmt.pix.height & ~1;
 	subfmt.format.code = MEDIA_BUS_FMT_FIXED;
@@ -1464,7 +1464,9 @@
 					    .buf = tuner_analog_msg_data,
 					    .len =
 					    sizeof(tuner_analog_msg_data) };
-	struct v4l2_subdev_format subfmt;
+	struct v4l2_subdev_format subfmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
 	int ret;
 
 	/* switch tuner to analog mode so IF demod will become accessible */
@@ -1507,8 +1509,6 @@
 	v4l2_subdev_call(cxdev->tuner, video, s_std, cxdev->norm);
 	v4l2_subdev_call(cxdev->cx25840, video, s_std, cxdev->norm);
 
-	memset(&subfmt, 0, sizeof(subfmt));
-	subfmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 	subfmt.format.width = cxdev->width;
 	subfmt.format.height = cxdev->height;
 	subfmt.format.code = MEDIA_BUS_FMT_FIXED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/dib0700_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/dib0700_core.c
@@ -618,8 +618,6 @@
 		deb_info("the endpoint number (%i) is not correct, use the adapter id instead", adap->fe_adap[0].stream.props.endpoint);
 		if (onoff)
 			st->channel_state |=	1 << (adap->id);
-		else
-			st->channel_state |=	1 << ~(adap->id);
 	} else {
 		if (onoff)
 			st->channel_state |=	1 << (adap->fe_adap[0].stream.props.endpoint-2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/dib0700_devices.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/dib0700_devices.c
@@ -2419,7 +2419,12 @@
 
 	adap->fe_adap[0].fe = dvb_attach(dib9000_attach, &adap->dev->i2c_adap, 0x80, &stk9090m_config);
 
-	return adap->fe_adap[0].fe == NULL ?  -ENODEV : 0;
+	if (!adap->fe_adap[0].fe) {
+		release_firmware(state->frontend_firmware);
+		return -ENODEV;
+	}
+
+	return 0;
 }
 
 static int dib9090_tuner_attach(struct dvb_usb_adapter *adap)
@@ -2492,8 +2497,10 @@
 	dib9000_i2c_enumeration(&adap->dev->i2c_adap, 1, 0x20, 0x80);
 	adap->fe_adap[0].fe = dvb_attach(dib9000_attach, &adap->dev->i2c_adap, 0x80, &nim9090md_config[0]);
 
-	if (adap->fe_adap[0].fe == NULL)
+	if (!adap->fe_adap[0].fe) {
+		release_firmware(state->frontend_firmware);
 		return -ENODEV;
+	}
 
 	i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_3_4, 0);
 	dib9000_i2c_enumeration(i2c, 1, 0x12, 0x82);
@@ -2501,7 +2508,12 @@
 	fe_slave = dvb_attach(dib9000_attach, i2c, 0x82, &nim9090md_config[1]);
 	dib9000_set_slave_frontend(adap->fe_adap[0].fe, fe_slave);
 
-	return fe_slave == NULL ?  -ENODEV : 0;
+	if (!fe_slave) {
+		release_firmware(state->frontend_firmware);
+		return -ENODEV;
+	}
+
+	return 0;
 }
 
 static int nim9090md_tuner_attach(struct dvb_usb_adapter *adap)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/dibusb-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/dibusb-common.c
@@ -223,7 +223,7 @@
 	u8 *buf;
 	int rc;
 
-	buf = kmalloc(2, GFP_KERNEL);
+	buf = kzalloc(2, GFP_KERNEL);
 	if (!buf)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/digitv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/digitv.c
@@ -63,6 +63,10 @@
 		warn("more than 2 i2c messages at a time is not handled yet. TODO.");
 
 	for (i = 0; i < num; i++) {
+		if (msg[i].len < 1) {
+			i = -EOPNOTSUPP;
+			break;
+		}
 		/* write/read request */
 		if (i+1 < num && (msg[i+1].flags & I2C_M_RD)) {
 			if (digitv_ctrl_msg(d, USB_READ_COFDM, msg[i].buf[0], NULL, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/dvb-usb-init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/dvb-usb-init.c
@@ -81,7 +81,7 @@
 
 		ret = dvb_usb_adapter_stream_init(adap);
 		if (ret)
-			return ret;
+			goto stream_init_err;
 
 		ret = dvb_usb_adapter_dvb_init(adap, adapter_nrs);
 		if (ret)
@@ -114,6 +114,8 @@
 	dvb_usb_adapter_dvb_exit(adap);
 dvb_init_err:
 	dvb_usb_adapter_stream_exit(adap);
+stream_init_err:
+	kfree(adap->priv);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/dw2102.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/dw2102.c
@@ -128,6 +128,10 @@
 
 	switch (num) {
 	case 2:
+		if (msg[0].len < 1) {
+			num = -EOPNOTSUPP;
+			break;
+		}
 		/* read stv0299 register */
 		value = msg[0].buf[0];/* register */
 		for (i = 0; i < msg[1].len; i++) {
@@ -139,6 +143,10 @@
 	case 1:
 		switch (msg[0].addr) {
 		case 0x68:
+			if (msg[0].len < 2) {
+				num = -EOPNOTSUPP;
+				break;
+			}
 			/* write to stv0299 register */
 			buf6[0] = 0x2a;
 			buf6[1] = msg[0].buf[0];
@@ -148,6 +156,10 @@
 			break;
 		case 0x60:
 			if (msg[0].flags == 0) {
+				if (msg[0].len < 4) {
+					num = -EOPNOTSUPP;
+					break;
+				}
 			/* write to tuner pll */
 				buf6[0] = 0x2c;
 				buf6[1] = 5;
@@ -159,6 +171,10 @@
 				dw210x_op_rw(d->udev, 0xb2, 0, 0,
 						buf6, 7, DW210X_WRITE_MSG);
 			} else {
+				if (msg[0].len < 1) {
+					num = -EOPNOTSUPP;
+					break;
+				}
 			/* read from tuner */
 				dw210x_op_rw(d->udev, 0xb5, 0, 0,
 						buf6, 1, DW210X_READ_MSG);
@@ -166,12 +182,20 @@
 			}
 			break;
 		case (DW2102_RC_QUERY):
+			if (msg[0].len < 2) {
+				num = -EOPNOTSUPP;
+				break;
+			}
 			dw210x_op_rw(d->udev, 0xb8, 0, 0,
 					buf6, 2, DW210X_READ_MSG);
 			msg[0].buf[0] = buf6[0];
 			msg[0].buf[1] = buf6[1];
 			break;
 		case (DW2102_VOLTAGE_CTRL):
+			if (msg[0].len < 1) {
+				num = -EOPNOTSUPP;
+				break;
+			}
 			buf6[0] = 0x30;
 			buf6[1] = msg[0].buf[0];
 			dw210x_op_rw(d->udev, 0xb2, 0, 0,
@@ -692,6 +716,7 @@
 {
 	struct dvb_usb_device *d = i2c_get_adapdata(adap);
 	struct dw2102_state *state;
+	int j;
 
 	if (!d)
 		return -ENODEV;
@@ -705,11 +730,11 @@
 		return -EAGAIN;
 	}
 
-	switch (num) {
-	case 1:
-		switch (msg[0].addr) {
+	j = 0;
+	while (j < num) {
+		switch (msg[j].addr) {
 		case SU3000_STREAM_CTRL:
-			state->data[0] = msg[0].buf[0] + 0x36;
+			state->data[0] = msg[j].buf[0] + 0x36;
 			state->data[1] = 3;
 			state->data[2] = 0;
 			if (dvb_usb_generic_rw(d, state->data, 3,
@@ -721,61 +746,86 @@
 			if (dvb_usb_generic_rw(d, state->data, 1,
 					state->data, 2, 0) < 0)
 				err("i2c transfer failed.");
-			msg[0].buf[1] = state->data[0];
-			msg[0].buf[0] = state->data[1];
+			msg[j].buf[1] = state->data[0];
+			msg[j].buf[0] = state->data[1];
 			break;
 		default:
-			if (3 + msg[0].len > sizeof(state->data)) {
-				warn("i2c wr: len=%d is too big!\n",
-				     msg[0].len);
+			/* if the current write msg is followed by a another
+			 * read msg to/from the same address
+			 */
+			if ((j+1 < num) && (msg[j+1].flags & I2C_M_RD) &&
+			    (msg[j].addr == msg[j+1].addr)) {
+				/* join both i2c msgs to one usb read command */
+				if (4 + msg[j].len > sizeof(state->data)) {
+					warn("i2c combined wr/rd: write len=%d is too big!\n",
+					    msg[j].len);
+					num = -EOPNOTSUPP;
+					break;
+				}
+				if (1 + msg[j+1].len > sizeof(state->data)) {
+					warn("i2c combined wr/rd: read len=%d is too big!\n",
+					    msg[j+1].len);
+					num = -EOPNOTSUPP;
+					break;
+				}
+
+				state->data[0] = 0x09;
+				state->data[1] = msg[j].len;
+				state->data[2] = msg[j+1].len;
+				state->data[3] = msg[j].addr;
+				memcpy(&state->data[4], msg[j].buf, msg[j].len);
+
+				if (dvb_usb_generic_rw(d, state->data, msg[j].len + 4,
+					state->data, msg[j+1].len + 1, 0) < 0)
+					err("i2c transfer failed.");
+
+				memcpy(msg[j+1].buf, &state->data[1], msg[j+1].len);
+				j++;
+				break;
+			}
+
+			if (msg[j].flags & I2C_M_RD) {
+				/* single read */
+				if (4 + msg[j].len > sizeof(state->data)) {
+					warn("i2c rd: len=%d is too big!\n", msg[j].len);
+					num = -EOPNOTSUPP;
+					break;
+				}
+
+				state->data[0] = 0x09;
+				state->data[1] = 0;
+				state->data[2] = msg[j].len;
+				state->data[3] = msg[j].addr;
+				memcpy(&state->data[4], msg[j].buf, msg[j].len);
+
+				if (dvb_usb_generic_rw(d, state->data, 4,
+					state->data, msg[j].len + 1, 0) < 0)
+					err("i2c transfer failed.");
+
+				memcpy(msg[j].buf, &state->data[1], msg[j].len);
+				break;
+			}
+
+			/* single write */
+			if (3 + msg[j].len > sizeof(state->data)) {
+				warn("i2c wr: len=%d is too big!\n", msg[j].len);
 				num = -EOPNOTSUPP;
 				break;
 			}
 
-			/* always i2c write*/
 			state->data[0] = 0x08;
-			state->data[1] = msg[0].addr;
-			state->data[2] = msg[0].len;
+			state->data[1] = msg[j].addr;
+			state->data[2] = msg[j].len;
 
-			memcpy(&state->data[3], msg[0].buf, msg[0].len);
+			memcpy(&state->data[3], msg[j].buf, msg[j].len);
 
-			if (dvb_usb_generic_rw(d, state->data, msg[0].len + 3,
+			if (dvb_usb_generic_rw(d, state->data, msg[j].len + 3,
 						state->data, 1, 0) < 0)
 				err("i2c transfer failed.");
+		} // switch
+		j++;
 
-		}
-		break;
-	case 2:
-		/* always i2c read */
-		if (4 + msg[0].len > sizeof(state->data)) {
-			warn("i2c rd: len=%d is too big!\n",
-			     msg[0].len);
-			num = -EOPNOTSUPP;
-			break;
-		}
-		if (1 + msg[1].len > sizeof(state->data)) {
-			warn("i2c rd: len=%d is too big!\n",
-			     msg[1].len);
-			num = -EOPNOTSUPP;
-			break;
-		}
-
-		state->data[0] = 0x09;
-		state->data[1] = msg[0].len;
-		state->data[2] = msg[1].len;
-		state->data[3] = msg[0].addr;
-		memcpy(&state->data[4], msg[0].buf, msg[0].len);
-
-		if (dvb_usb_generic_rw(d, state->data, msg[0].len + 4,
-					state->data, msg[1].len + 1, 0) < 0)
-			err("i2c transfer failed.");
-
-		memcpy(msg[1].buf, &state->data[1], msg[1].len);
-		break;
-	default:
-		warn("more than 2 i2c messages at a time is not handled yet.");
-		break;
-	}
+	} // while
 	mutex_unlock(&d->data_mutex);
 	mutex_unlock(&d->i2c_mutex);
 	return num;
@@ -946,7 +996,7 @@
 	for (i = 0; i < 6; i++) {
 		obuf[1] = 0xf0 + i;
 		if (i2c_transfer(&d->i2c_adap, msg, 2) != 2)
-			break;
+			return -1;
 		else
 			mac[i] = ibuf[0];
 	}
@@ -2150,46 +2200,153 @@
 	}
 };
 
-static const struct dvb_usb_device_description d1100 = {
-	"Prof 1100 USB ",
-	{&dw2102_table[PROF_1100], NULL},
-	{NULL},
-};
+static struct dvb_usb_device_properties p1100_properties = {
+	.caps = DVB_USB_IS_AN_I2C_ADAPTER,
+	.usb_ctrl = DEVICE_SPECIFIC,
+	.size_of_priv = sizeof(struct dw2102_state),
+	.firmware = P1100_FIRMWARE,
+	.no_reconnect = 1,
 
-static const struct dvb_usb_device_description d660 = {
-	"TeVii S660 USB",
-	{&dw2102_table[TEVII_S660], NULL},
-	{NULL},
-};
+	.i2c_algo = &s6x0_i2c_algo,
+	.rc.core = {
+		.rc_interval = 150,
+		.rc_codes = RC_MAP_TBS_NEC,
+		.module_name = "dw2102",
+		.allowed_protos   = RC_PROTO_BIT_NEC,
+		.rc_query = prof_rc_query,
+	},
 
-static const struct dvb_usb_device_description d480_1 = {
-	"TeVii S480.1 USB",
-	{&dw2102_table[TEVII_S480_1], NULL},
-	{NULL},
+	.generic_bulk_ctrl_endpoint = 0x81,
+	.num_adapters = 1,
+	.download_firmware = dw2102_load_firmware,
+	.read_mac_address = s6x0_read_mac_address,
+	.adapter = {
+		{
+			.num_frontends = 1,
+			.fe = {{
+				.frontend_attach = stv0288_frontend_attach,
+				.stream = {
+					.type = USB_BULK,
+					.count = 8,
+					.endpoint = 0x82,
+					.u = {
+						.bulk = {
+							.buffersize = 4096,
+						}
+					}
+				},
+			} },
+		}
+	},
+	.num_device_descs = 1,
+	.devices = {
+		{"Prof 1100 USB ",
+			{&dw2102_table[PROF_1100], NULL},
+			{NULL},
+		},
+	}
 };
 
-static const struct dvb_usb_device_description d480_2 = {
-	"TeVii S480.2 USB",
-	{&dw2102_table[TEVII_S480_2], NULL},
-	{NULL},
-};
+static struct dvb_usb_device_properties s660_properties = {
+	.caps = DVB_USB_IS_AN_I2C_ADAPTER,
+	.usb_ctrl = DEVICE_SPECIFIC,
+	.size_of_priv = sizeof(struct dw2102_state),
+	.firmware = S660_FIRMWARE,
+	.no_reconnect = 1,
 
-static const struct dvb_usb_device_description d7500 = {
-	"Prof 7500 USB DVB-S2",
-	{&dw2102_table[PROF_7500], NULL},
-	{NULL},
-};
+	.i2c_algo = &s6x0_i2c_algo,
+	.rc.core = {
+		.rc_interval = 150,
+		.rc_codes = RC_MAP_TEVII_NEC,
+		.module_name = "dw2102",
+		.allowed_protos   = RC_PROTO_BIT_NEC,
+		.rc_query = dw2102_rc_query,
+	},
 
-static const struct dvb_usb_device_description d421 = {
-	"TeVii S421 PCI",
-	{&dw2102_table[TEVII_S421], NULL},
-	{NULL},
+	.generic_bulk_ctrl_endpoint = 0x81,
+	.num_adapters = 1,
+	.download_firmware = dw2102_load_firmware,
+	.read_mac_address = s6x0_read_mac_address,
+	.adapter = {
+		{
+			.num_frontends = 1,
+			.fe = {{
+				.frontend_attach = ds3000_frontend_attach,
+				.stream = {
+					.type = USB_BULK,
+					.count = 8,
+					.endpoint = 0x82,
+					.u = {
+						.bulk = {
+							.buffersize = 4096,
+						}
+					}
+				},
+			} },
+		}
+	},
+	.num_device_descs = 3,
+	.devices = {
+		{"TeVii S660 USB",
+			{&dw2102_table[TEVII_S660], NULL},
+			{NULL},
+		},
+		{"TeVii S480.1 USB",
+			{&dw2102_table[TEVII_S480_1], NULL},
+			{NULL},
+		},
+		{"TeVii S480.2 USB",
+			{&dw2102_table[TEVII_S480_2], NULL},
+			{NULL},
+		},
+	}
 };
 
-static const struct dvb_usb_device_description d632 = {
-	"TeVii S632 USB",
-	{&dw2102_table[TEVII_S632], NULL},
-	{NULL},
+static struct dvb_usb_device_properties p7500_properties = {
+	.caps = DVB_USB_IS_AN_I2C_ADAPTER,
+	.usb_ctrl = DEVICE_SPECIFIC,
+	.size_of_priv = sizeof(struct dw2102_state),
+	.firmware = P7500_FIRMWARE,
+	.no_reconnect = 1,
+
+	.i2c_algo = &s6x0_i2c_algo,
+	.rc.core = {
+		.rc_interval = 150,
+		.rc_codes = RC_MAP_TBS_NEC,
+		.module_name = "dw2102",
+		.allowed_protos   = RC_PROTO_BIT_NEC,
+		.rc_query = prof_rc_query,
+	},
+
+	.generic_bulk_ctrl_endpoint = 0x81,
+	.num_adapters = 1,
+	.download_firmware = dw2102_load_firmware,
+	.read_mac_address = s6x0_read_mac_address,
+	.adapter = {
+		{
+			.num_frontends = 1,
+			.fe = {{
+				.frontend_attach = prof_7500_frontend_attach,
+				.stream = {
+					.type = USB_BULK,
+					.count = 8,
+					.endpoint = 0x82,
+					.u = {
+						.bulk = {
+							.buffersize = 4096,
+						}
+					}
+				},
+			} },
+		}
+	},
+	.num_device_descs = 1,
+	.devices = {
+		{"Prof 7500 USB DVB-S2",
+			{&dw2102_table[PROF_7500], NULL},
+			{NULL},
+		},
+	}
 };
 
 static struct dvb_usb_device_properties su3000_properties = {
@@ -2273,6 +2430,59 @@
 	}
 };
 
+static struct dvb_usb_device_properties s421_properties = {
+	.caps = DVB_USB_IS_AN_I2C_ADAPTER,
+	.usb_ctrl = DEVICE_SPECIFIC,
+	.size_of_priv = sizeof(struct dw2102_state),
+	.power_ctrl = su3000_power_ctrl,
+	.num_adapters = 1,
+	.identify_state	= su3000_identify_state,
+	.i2c_algo = &su3000_i2c_algo,
+
+	.rc.core = {
+		.rc_interval = 150,
+		.rc_codes = RC_MAP_SU3000,
+		.module_name = "dw2102",
+		.allowed_protos   = RC_PROTO_BIT_RC5,
+		.rc_query = su3000_rc_query,
+	},
+
+	.read_mac_address = su3000_read_mac_address,
+
+	.generic_bulk_ctrl_endpoint = 0x01,
+
+	.adapter = {
+		{
+		.num_frontends = 1,
+		.fe = {{
+			.streaming_ctrl   = su3000_streaming_ctrl,
+			.frontend_attach  = m88rs2000_frontend_attach,
+			.stream = {
+				.type = USB_BULK,
+				.count = 8,
+				.endpoint = 0x82,
+				.u = {
+					.bulk = {
+						.buffersize = 4096,
+					}
+				}
+			}
+		} },
+		}
+	},
+	.num_device_descs = 2,
+	.devices = {
+		{ "TeVii S421 PCI",
+			{ &dw2102_table[TEVII_S421], NULL },
+			{ NULL },
+		},
+		{ "TeVii S632 USB",
+			{ &dw2102_table[TEVII_S632], NULL },
+			{ NULL },
+		},
+	}
+};
+
 static struct dvb_usb_device_properties t220_properties = {
 	.caps = DVB_USB_IS_AN_I2C_ADAPTER,
 	.usb_ctrl = DEVICE_SPECIFIC,
@@ -2390,101 +2600,33 @@
 static int dw2102_probe(struct usb_interface *intf,
 		const struct usb_device_id *id)
 {
-	int retval = -ENOMEM;
-	struct dvb_usb_device_properties *p1100;
-	struct dvb_usb_device_properties *s660;
-	struct dvb_usb_device_properties *p7500;
-	struct dvb_usb_device_properties *s421;
-
-	p1100 = kmemdup(&s6x0_properties,
-			sizeof(struct dvb_usb_device_properties), GFP_KERNEL);
-	if (!p1100)
-		goto err0;
-
-	/* copy default structure */
-	/* fill only different fields */
-	p1100->firmware = P1100_FIRMWARE;
-	p1100->devices[0] = d1100;
-	p1100->rc.core.rc_query = prof_rc_query;
-	p1100->rc.core.rc_codes = RC_MAP_TBS_NEC;
-	p1100->adapter->fe[0].frontend_attach = stv0288_frontend_attach;
-
-	s660 = kmemdup(&s6x0_properties,
-		       sizeof(struct dvb_usb_device_properties), GFP_KERNEL);
-	if (!s660)
-		goto err1;
-
-	s660->firmware = S660_FIRMWARE;
-	s660->num_device_descs = 3;
-	s660->devices[0] = d660;
-	s660->devices[1] = d480_1;
-	s660->devices[2] = d480_2;
-	s660->adapter->fe[0].frontend_attach = ds3000_frontend_attach;
-
-	p7500 = kmemdup(&s6x0_properties,
-			sizeof(struct dvb_usb_device_properties), GFP_KERNEL);
-	if (!p7500)
-		goto err2;
-
-	p7500->firmware = P7500_FIRMWARE;
-	p7500->devices[0] = d7500;
-	p7500->rc.core.rc_query = prof_rc_query;
-	p7500->rc.core.rc_codes = RC_MAP_TBS_NEC;
-	p7500->adapter->fe[0].frontend_attach = prof_7500_frontend_attach;
-
-
-	s421 = kmemdup(&su3000_properties,
-		       sizeof(struct dvb_usb_device_properties), GFP_KERNEL);
-	if (!s421)
-		goto err3;
-
-	s421->num_device_descs = 2;
-	s421->devices[0] = d421;
-	s421->devices[1] = d632;
-	s421->adapter->fe[0].frontend_attach = m88rs2000_frontend_attach;
-
-	if (0 == dvb_usb_device_init(intf, &dw2102_properties,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, &dw2104_properties,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, &dw3101_properties,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, &s6x0_properties,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, p1100,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, s660,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, p7500,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, s421,
-			THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, &su3000_properties,
-			 THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, &t220_properties,
-			 THIS_MODULE, NULL, adapter_nr) ||
-	    0 == dvb_usb_device_init(intf, &tt_s2_4600_properties,
-			 THIS_MODULE, NULL, adapter_nr)) {
-
-		/* clean up copied properties */
-		kfree(s421);
-		kfree(p7500);
-		kfree(s660);
-		kfree(p1100);
+	if (!(dvb_usb_device_init(intf, &dw2102_properties,
+			          THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &dw2104_properties,
+				  THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &dw3101_properties,
+			          THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &s6x0_properties,
+			          THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &p1100_properties,
+			          THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &s660_properties,
+				  THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &p7500_properties,
+				  THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &s421_properties,
+				  THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &su3000_properties,
+				  THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &t220_properties,
+				  THIS_MODULE, NULL, adapter_nr) &&
+	      dvb_usb_device_init(intf, &tt_s2_4600_properties,
+				  THIS_MODULE, NULL, adapter_nr))) {
 
 		return 0;
 	}
 
-	retval = -ENODEV;
-	kfree(s421);
-err3:
-	kfree(p7500);
-err2:
-	kfree(s660);
-err1:
-	kfree(p1100);
-err0:
-	return retval;
+	return -ENODEV;
 }
 
 static void dw2102_disconnect(struct usb_interface *intf)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/dvb-usb/m920x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/dvb-usb/m920x.c
@@ -274,6 +274,12 @@
 			/* Should check for ack here, if we knew how. */
 		}
 		if (msg[i].flags & I2C_M_RD) {
+			char *read = kmalloc(1, GFP_KERNEL);
+			if (!read) {
+				ret = -ENOMEM;
+				goto unlock;
+			}
+
 			for (j = 0; j < msg[i].len; j++) {
 				/* Last byte of transaction?
 				 * Send STOP, otherwise send ACK. */
@@ -281,9 +287,14 @@
 
 				if ((ret = m920x_read(d->udev, M9206_I2C, 0x0,
 						      0x20 | stop,
-						      &msg[i].buf[j], 1)) != 0)
+						      read, 1)) != 0) {
+					kfree(read);
 					goto unlock;
+				}
+				msg[i].buf[j] = read[0];
 			}
+
+			kfree(read);
 		} else {
 			for (j = 0; j < msg[i].len; j++) {
 				/* Last byte of transaction? Then send STOP. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/em28xx/em28xx-cards.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/em28xx/em28xx-cards.c
@@ -3625,8 +3625,10 @@
 
 	if (dev->is_audio_only) {
 		retval = em28xx_audio_setup(dev);
-		if (retval)
-			return -ENODEV;
+		if (retval) {
+			retval = -ENODEV;
+			goto err_deinit_media;
+		}
 		em28xx_init_extension(dev);
 
 		return 0;
@@ -3645,7 +3647,7 @@
 		dev_err(&dev->intf->dev,
 			"%s: em28xx_i2c_register bus 0 - error [%d]!\n",
 		       __func__, retval);
-		return retval;
+		goto err_deinit_media;
 	}
 
 	/* register i2c bus 1 */
@@ -3661,9 +3663,7 @@
 				"%s: em28xx_i2c_register bus 1 - error [%d]!\n",
 				__func__, retval);
 
-			em28xx_i2c_unregister(dev, 0);
-
-			return retval;
+			goto err_unreg_i2c;
 		}
 	}
 
@@ -3671,6 +3671,12 @@
 	em28xx_card_setup(dev);
 
 	return 0;
+
+err_unreg_i2c:
+	em28xx_i2c_unregister(dev, 0);
+err_deinit_media:
+	em28xx_unregister_media_device(dev);
+	return retval;
 }
 
 static int em28xx_duplicate_dev(struct em28xx *dev)
@@ -3925,6 +3931,8 @@
 		goto err_free;
 	}
 
+	kref_init(&dev->ref);
+
 	dev->devno = nr;
 	dev->model = id->driver_info;
 	dev->alt   = -1;
@@ -4025,6 +4033,8 @@
 	}
 
 	if (dev->board.has_dual_ts && em28xx_duplicate_dev(dev) == 0) {
+		kref_init(&dev->dev_next->ref);
+
 		dev->dev_next->ts = SECONDARY_TS;
 		dev->dev_next->alt   = -1;
 		dev->dev_next->is_audio_only = has_vendor_audio &&
@@ -4079,12 +4089,8 @@
 			em28xx_write_reg(dev, 0x0b, 0x82);
 			mdelay(100);
 		}
-
-		kref_init(&dev->dev_next->ref);
 	}
 
-	kref_init(&dev->ref);
-
 	request_modules(dev);
 
 	/*
@@ -4093,6 +4099,10 @@
 	 * topology will likely change after the load of the em28xx subdrivers.
 	 */
 #ifdef CONFIG_MEDIA_CONTROLLER
+	/*
+	 * No need to check the return value, the device will still be
+	 * usable without media controller API.
+	 */
 	retval = media_device_register(dev->media_dev);
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/em28xx/em28xx-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/em28xx/em28xx-core.c
@@ -89,7 +89,7 @@
 	mutex_lock(&dev->ctrl_urb_lock);
 	ret = usb_control_msg(udev, pipe, req,
 			      USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			      0x0000, reg, dev->urb_buf, len, HZ);
+			      0x0000, reg, dev->urb_buf, len, 1000);
 	if (ret < 0) {
 		em28xx_regdbg("(pipe 0x%08x): IN:  %02x %02x %02x %02x %02x %02x %02x %02x  failed with error %i\n",
 			      pipe,
@@ -158,7 +158,7 @@
 	memcpy(dev->urb_buf, buf, len);
 	ret = usb_control_msg(udev, pipe, req,
 			      USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			      0x0000, reg, dev->urb_buf, len, HZ);
+			      0x0000, reg, dev->urb_buf, len, 1000);
 	mutex_unlock(&dev->ctrl_urb_lock);
 
 	if (ret < 0) {
@@ -1154,8 +1154,9 @@
 	dev_info(&dev->intf->dev, "Suspending extensions\n");
 	mutex_lock(&em28xx_devlist_mutex);
 	list_for_each_entry(ops, &em28xx_extension_devlist, next) {
-		if (ops->suspend)
-			ops->suspend(dev);
+		if (!ops->suspend)
+			continue;
+		ops->suspend(dev);
 		if (dev->dev_next)
 			ops->suspend(dev->dev_next);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/go7007/go7007-driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/go7007/go7007-driver.c
@@ -80,7 +80,7 @@
 	const struct firmware *fw_entry;
 	char fw_name[] = "go7007/go7007fw.bin";
 	void *bounce;
-	int fw_len, rv = 0;
+	int fw_len;
 	u16 intr_val, intr_data;
 
 	if (go->boot_fw == NULL) {
@@ -109,9 +109,11 @@
 	    go7007_read_interrupt(go, &intr_val, &intr_data) < 0 ||
 			(intr_val & ~0x1) != 0x5a5a) {
 		v4l2_err(go, "error transferring firmware\n");
-		rv = -1;
+		kfree(go->boot_fw);
+		go->boot_fw = NULL;
+		return -1;
 	}
-	return rv;
+	return 0;
 }
 
 MODULE_FIRMWARE("go7007/go7007fw.bin");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/go7007/go7007-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/go7007/go7007-i2c.c
@@ -165,8 +165,6 @@
 		} else if (msgs[i].len == 3) {
 			if (msgs[i].flags & I2C_M_RD)
 				return -EIO;
-			if (msgs[i].len != 3)
-				return -EIO;
 			if (go7007_i2c_xfer(go, msgs[i].addr, 0,
 					(msgs[i].buf[0] << 8) | msgs[i].buf[1],
 					0x01, &msgs[i].buf[2]) < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/go7007/go7007-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/go7007/go7007-usb.c
@@ -1201,7 +1201,9 @@
 				u16 channel;
 
 				/* read channel number from GPIO[1:0] */
-				go7007_read_addr(go, 0x3c81, &channel);
+				if (go7007_read_addr(go, 0x3c81, &channel))
+					goto allocfail;
+
 				channel &= 0x3;
 				go->board_id = GO7007_BOARDID_ADLINK_MPG24;
 				usb->board = board = &board_adlink_mpg24;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/go7007/s2250-board.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/go7007/s2250-board.c
@@ -504,6 +504,7 @@
 	u8 *data;
 	struct go7007 *go = i2c_get_adapdata(adapter);
 	struct go7007_usb *usb = go->hpi_context;
+	int err = -EIO;
 
 	audio = i2c_new_dummy_device(adapter, TLV320_ADDRESS >> 1);
 	if (IS_ERR(audio))
@@ -532,11 +533,8 @@
 		V4L2_CID_HUE, -512, 511, 1, 0);
 	sd->ctrl_handler = &state->hdl;
 	if (state->hdl.error) {
-		int err = state->hdl.error;
-
-		v4l2_ctrl_handler_free(&state->hdl);
-		kfree(state);
-		return err;
+		err = state->hdl.error;
+		goto fail;
 	}
 
 	state->std = V4L2_STD_NTSC;
@@ -600,7 +598,7 @@
 	i2c_unregister_device(audio);
 	v4l2_ctrl_handler_free(&state->hdl);
 	kfree(state);
-	return -EIO;
+	return err;
 }
 
 static int s2250_remove(struct i2c_client *client)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/gspca/cpia1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/gspca/cpia1.c
@@ -18,6 +18,7 @@
 
 #include <linux/input.h>
 #include <linux/sched/signal.h>
+#include <linux/bitops.h>
 
 #include "gspca.h"
 
@@ -1028,6 +1029,8 @@
 			sd->params.exposure.expMode = 2;
 			sd->exposure_status = EXPOSURE_NORMAL;
 		}
+		if (sd->params.exposure.gain >= BITS_PER_TYPE(currentexp))
+			return -EINVAL;
 		currentexp = currentexp << sd->params.exposure.gain;
 		sd->params.exposure.gain = 0;
 		/* round down current exposure to nearest value */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/gspca/ov534.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/gspca/ov534.c
@@ -847,7 +847,7 @@
 		r = rate_1;
 		i = ARRAY_SIZE(rate_1);
 	}
-	while (--i > 0) {
+	while (--i >= 0) {
 		if (sd->frame_rate >= r->fps)
 			break;
 		r++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/hdpvr/hdpvr-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/hdpvr/hdpvr-video.c
@@ -308,7 +308,6 @@
 
 	dev->status = STATUS_STREAMING;
 
-	INIT_WORK(&dev->worker, hdpvr_transmit_buffers);
 	schedule_work(&dev->worker);
 
 	v4l2_dbg(MSG_BUFFER, hdpvr_debug, &dev->v4l2_dev,
@@ -410,7 +409,7 @@
 	struct hdpvr_device *dev = video_drvdata(file);
 	struct hdpvr_buffer *buf = NULL;
 	struct urb *urb;
-	unsigned int ret = 0;
+	int ret = 0;
 	int rem, cnt;
 
 	if (*pos)
@@ -1165,6 +1164,9 @@
 	bool ac3 = dev->flags & HDPVR_FLAG_AC3_CAP;
 	int res;
 
+	// initialize dev->worker
+	INIT_WORK(&dev->worker, hdpvr_transmit_buffers);
+
 	dev->cur_std = V4L2_STD_525_60;
 	dev->width = 720;
 	dev->height = 480;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/pvrusb2/pvrusb2-context.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/pvrusb2/pvrusb2-context.c
@@ -90,8 +90,10 @@
 }
 
 
-static void pvr2_context_notify(struct pvr2_context *mp)
+static void pvr2_context_notify(void *ptr)
 {
+	struct pvr2_context *mp = ptr;
+
 	pvr2_context_set_notify(mp,!0);
 }
 
@@ -106,9 +108,7 @@
 		pvr2_trace(PVR2_TRACE_CTXT,
 			   "pvr2_context %p (initialize)", mp);
 		/* Finish hardware initialization */
-		if (pvr2_hdw_initialize(mp->hdw,
-					(void (*)(void *))pvr2_context_notify,
-					mp)) {
+		if (pvr2_hdw_initialize(mp->hdw, pvr2_context_notify, mp)) {
 			mp->video_stream.stream =
 				pvr2_hdw_get_video_stream(mp->hdw);
 			/* Trigger interface initialization.  By doing this
@@ -267,8 +267,9 @@
 void pvr2_context_disconnect(struct pvr2_context *mp)
 {
 	pvr2_hdw_disconnect(mp->hdw);
+	if (!pvr2_context_shutok())
+		pvr2_context_notify(mp);
 	mp->disconnect_flag = !0;
-	pvr2_context_notify(mp);
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/pvrusb2/pvrusb2-dvb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/pvrusb2/pvrusb2-dvb.c
@@ -88,8 +88,10 @@
 	return stat;
 }
 
-static void pvr2_dvb_notify(struct pvr2_dvb_adapter *adap)
+static void pvr2_dvb_notify(void *ptr)
 {
+	struct pvr2_dvb_adapter *adap = ptr;
+
 	wake_up(&adap->buffer_wait_data);
 }
 
@@ -149,7 +151,7 @@
 	}
 
 	pvr2_stream_set_callback(pvr->video_stream.stream,
-				 (pvr2_stream_callback) pvr2_dvb_notify, adap);
+				 pvr2_dvb_notify, adap);
 
 	ret = pvr2_stream_set_buffer_count(stream, PVR2_DVB_BUFFER_COUNT);
 	if (ret < 0) return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/pvrusb2/pvrusb2-hdw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/pvrusb2/pvrusb2-hdw.c
@@ -1467,7 +1467,7 @@
 	for (address = 0; address < fwsize; address += 0x800) {
 		memcpy(fw_ptr, fw_entry->data + address, 0x800);
 		ret += usb_control_msg(hdw->usb_dev, pipe, 0xa0, 0x40, address,
-				       0, fw_ptr, 0x800, HZ);
+				       0, fw_ptr, 0x800, 1000);
 	}
 
 	trace_firmware("Upload done, releasing device's CPU");
@@ -1605,7 +1605,7 @@
 			((u32 *)fw_ptr)[icnt] = swab32(((u32 *)fw_ptr)[icnt]);
 
 		ret |= usb_bulk_msg(hdw->usb_dev, pipe, fw_ptr,bcnt,
-				    &actual_length, HZ);
+				    &actual_length, 1000);
 		ret |= (actual_length != bcnt);
 		if (ret) break;
 		fw_done += bcnt;
@@ -2569,6 +2569,11 @@
 	} while (0);
 	mutex_unlock(&pvr2_unit_mtx);
 
+	INIT_WORK(&hdw->workpoll, pvr2_hdw_worker_poll);
+
+	if (hdw->unit_number == -1)
+		goto fail;
+
 	cnt1 = 0;
 	cnt2 = scnprintf(hdw->name+cnt1,sizeof(hdw->name)-cnt1,"pvrusb2");
 	cnt1 += cnt2;
@@ -2580,8 +2585,6 @@
 	if (cnt1 >= sizeof(hdw->name)) cnt1 = sizeof(hdw->name)-1;
 	hdw->name[cnt1] = 0;
 
-	INIT_WORK(&hdw->workpoll,pvr2_hdw_worker_poll);
-
 	pvr2_trace(PVR2_TRACE_INIT,"Driver unit number is %d, name is %s",
 		   hdw->unit_number,hdw->name);
 
@@ -2607,6 +2610,7 @@
 		del_timer_sync(&hdw->encoder_run_timer);
 		del_timer_sync(&hdw->encoder_wait_timer);
 		flush_work(&hdw->workpoll);
+		v4l2_device_unregister(&hdw->v4l2_dev);
 		usb_free_urb(hdw->ctl_read_urb);
 		usb_free_urb(hdw->ctl_write_urb);
 		kfree(hdw->ctl_read_buffer);
@@ -3438,7 +3442,7 @@
 						      0xa0,0xc0,
 						      address,0,
 						      hdw->fw_buffer+address,
-						      0x800,HZ);
+						      0x800,1000);
 				if (ret < 0) break;
 			}
 
@@ -3977,7 +3981,7 @@
 	/* Write the CPUCS register on the 8051.  The lsb of the register
 	   is the reset bit; a 1 asserts reset while a 0 clears it. */
 	pipe = usb_sndctrlpipe(hdw->usb_dev, 0);
-	ret = usb_control_msg(hdw->usb_dev,pipe,0xa0,0x40,0xe600,0,da,1,HZ);
+	ret = usb_control_msg(hdw->usb_dev,pipe,0xa0,0x40,0xe600,0,da,1,1000);
 	if (ret < 0) {
 		pvr2_trace(PVR2_TRACE_ERROR_LEGS,
 			   "cpureset_assert(%d) error=%d",val,ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/pvrusb2/pvrusb2-v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/pvrusb2/pvrusb2-v4l2.c
@@ -1037,8 +1037,10 @@
 }
 
 
-static void pvr2_v4l2_notify(struct pvr2_v4l2_fh *fhp)
+static void pvr2_v4l2_notify(void *ptr)
 {
+	struct pvr2_v4l2_fh *fhp = ptr;
+
 	wake_up(&fhp->wait_data);
 }
 
@@ -1071,7 +1073,7 @@
 
 	hdw = fh->channel.mc_head->hdw;
 	sp = fh->pdi->stream->stream;
-	pvr2_stream_set_callback(sp,(pvr2_stream_callback)pvr2_v4l2_notify,fh);
+	pvr2_stream_set_callback(sp, pvr2_v4l2_notify, fh);
 	pvr2_hdw_set_stream_type(hdw,fh->pdi->config);
 	if ((ret = pvr2_hdw_set_streaming(hdw,!0)) < 0) return ret;
 	return pvr2_ioread_set_enabled(fh->rhp,!0);
@@ -1202,11 +1204,6 @@
 		dip->minor_type = pvr2_v4l_type_video;
 		nr_ptr = video_nr;
 		caps |= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_AUDIO;
-		if (!dip->stream) {
-			pr_err(KBUILD_MODNAME
-				": Failed to set up pvrusb2 v4l video dev due to missing stream instance\n");
-			return;
-		}
 		break;
 	case VFL_TYPE_VBI:
 		dip->config = pvr2_config_vbi;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/s2255/s2255drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/s2255/s2255drv.c
@@ -247,7 +247,7 @@
 struct s2255_dev {
 	struct s2255_vc         vc[MAX_CHANNELS];
 	struct v4l2_device      v4l2_dev;
-	atomic_t                num_channels;
+	refcount_t		num_channels;
 	int			frames;
 	struct mutex		lock;	/* channels[].vdev.lock */
 	struct mutex		cmdlock; /* protects cmdbuf */
@@ -1550,11 +1550,11 @@
 		container_of(vdev, struct s2255_vc, vdev);
 
 	dprintk(dev, 4, "%s, chnls: %d\n", __func__,
-		atomic_read(&dev->num_channels));
+		refcount_read(&dev->num_channels));
 
 	v4l2_ctrl_handler_free(&vc->hdl);
 
-	if (atomic_dec_and_test(&dev->num_channels))
+	if (refcount_dec_and_test(&dev->num_channels))
 		s2255_destroy(dev);
 	return;
 }
@@ -1659,7 +1659,7 @@
 				"failed to register video device!\n");
 			break;
 		}
-		atomic_inc(&dev->num_channels);
+		refcount_inc(&dev->num_channels);
 		v4l2_info(&dev->v4l2_dev, "V4L2 device registered as %s\n",
 			  video_device_node_name(&vc->vdev));
 
@@ -1667,11 +1667,11 @@
 	pr_info("Sensoray 2255 V4L driver Revision: %s\n",
 		S2255_VERSION);
 	/* if no channels registered, return error and probe will fail*/
-	if (atomic_read(&dev->num_channels) == 0) {
+	if (refcount_read(&dev->num_channels) == 0) {
 		v4l2_device_unregister(&dev->v4l2_dev);
 		return ret;
 	}
-	if (atomic_read(&dev->num_channels) != MAX_CHANNELS)
+	if (refcount_read(&dev->num_channels) != MAX_CHANNELS)
 		pr_warn("s2255: Not all channels available.\n");
 	return 0;
 }
@@ -1882,7 +1882,7 @@
 				    USB_TYPE_VENDOR | USB_RECIP_DEVICE |
 				    USB_DIR_IN,
 				    Value, Index, buf,
-				    TransferBufferLength, HZ * 5);
+				    TransferBufferLength, USB_CTRL_SET_TIMEOUT);
 
 		if (r >= 0)
 			memcpy(TransferBuffer, buf, TransferBufferLength);
@@ -1891,7 +1891,7 @@
 		r = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, 0),
 				    Request, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 				    Value, Index, buf,
-				    TransferBufferLength, HZ * 5);
+				    TransferBufferLength, USB_CTRL_SET_TIMEOUT);
 	}
 	kfree(buf);
 	return r;
@@ -2220,7 +2220,7 @@
 		goto errorFWDATA1;
 	}
 
-	atomic_set(&dev->num_channels, 0);
+	refcount_set(&dev->num_channels, 0);
 	dev->pid = id->idProduct;
 	dev->fw_data = kzalloc(sizeof(struct s2255_fw), GFP_KERNEL);
 	if (!dev->fw_data)
@@ -2340,12 +2340,12 @@
 {
 	struct s2255_dev *dev = to_s2255_dev(usb_get_intfdata(interface));
 	int i;
-	int channels = atomic_read(&dev->num_channels);
+	int channels = refcount_read(&dev->num_channels);
 	mutex_lock(&dev->lock);
 	v4l2_device_disconnect(&dev->v4l2_dev);
 	mutex_unlock(&dev->lock);
 	/*see comments in the uvc_driver.c usb disconnect function */
-	atomic_inc(&dev->num_channels);
+	refcount_inc(&dev->num_channels);
 	/* unregister each video device. */
 	for (i = 0; i < channels; i++)
 		video_unregister_device(&dev->vc[i].vdev);
@@ -2358,7 +2358,7 @@
 		dev->vc[i].vidstatus_ready = 1;
 		wake_up(&dev->vc[i].wait_vidstatus);
 	}
-	if (atomic_dec_and_test(&dev->num_channels))
+	if (refcount_dec_and_test(&dev->num_channels))
 		s2255_destroy(dev);
 	dev_info(&interface->dev, "%s\n", __func__);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/siano/smsusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/siano/smsusb.c
@@ -179,6 +179,8 @@
 
 	for (i = 0; i < MAX_URBS; i++) {
 		usb_kill_urb(&dev->surbs[i].urb);
+		if (dev->surbs[i].wq.func)
+			cancel_work_sync(&dev->surbs[i].wq);
 
 		if (dev->surbs[i].cb) {
 			smscore_putbuffer(dev->coredev, dev->surbs[i].cb);
@@ -453,12 +455,7 @@
 	rc = smscore_register_device(&params, &dev->coredev, 0, mdev);
 	if (rc < 0) {
 		pr_err("smscore_register_device(...) failed, rc %d\n", rc);
-		smsusb_term_device(intf);
-#ifdef CONFIG_MEDIA_CONTROLLER_DVB
-		media_device_unregister(mdev);
-#endif
-		kfree(mdev);
-		return rc;
+		goto err_unregister_device;
 	}
 
 	smscore_set_board_id(dev->coredev, board_id);
@@ -475,8 +472,7 @@
 	rc = smsusb_start_streaming(dev);
 	if (rc < 0) {
 		pr_err("smsusb_start_streaming(...) failed\n");
-		smsusb_term_device(intf);
-		return rc;
+		goto err_unregister_device;
 	}
 
 	dev->state = SMSUSB_ACTIVE;
@@ -484,13 +480,20 @@
 	rc = smscore_start_device(dev->coredev);
 	if (rc < 0) {
 		pr_err("smscore_start_device(...) failed\n");
-		smsusb_term_device(intf);
-		return rc;
+		goto err_unregister_device;
 	}
 
 	pr_debug("device 0x%p created\n", dev);
 
 	return rc;
+
+err_unregister_device:
+	smsusb_term_device(intf);
+#ifdef CONFIG_MEDIA_CONTROLLER_DVB
+	media_device_unregister(mdev);
+#endif
+	kfree(mdev);
+	return rc;
 }
 
 static int smsusb_probe(struct usb_interface *intf,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/stk1160/stk1160-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/stk1160/stk1160-core.c
@@ -65,7 +65,7 @@
 		return -ENOMEM;
 	ret = usb_control_msg(dev->udev, pipe, 0x00,
 			USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			0x00, reg, buf, sizeof(u8), HZ);
+			0x00, reg, buf, sizeof(u8), 1000);
 	if (ret < 0) {
 		stk1160_err("read failed on reg 0x%x (%d)\n",
 			reg, ret);
@@ -85,7 +85,7 @@
 
 	ret =  usb_control_msg(dev->udev, pipe, 0x01,
 			USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			value, reg, NULL, 0, HZ);
+			value, reg, NULL, 0, 1000);
 	if (ret < 0) {
 		stk1160_err("write failed on reg 0x%x (%d)\n",
 			reg, ret);
@@ -403,7 +403,7 @@
 	/* Here is the only place where isoc get released */
 	stk1160_uninit_isoc(dev);
 
-	stk1160_clear_queue(dev);
+	stk1160_clear_queue(dev, VB2_BUF_STATE_ERROR);
 
 	video_unregister_device(&dev->vdev);
 	v4l2_device_disconnect(&dev->v4l2_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/stk1160/stk1160-v4l.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/stk1160/stk1160-v4l.c
@@ -258,7 +258,7 @@
 	stk1160_uninit_isoc(dev);
 out_stop_hw:
 	usb_set_interface(dev->udev, 0, 0);
-	stk1160_clear_queue(dev);
+	stk1160_clear_queue(dev, VB2_BUF_STATE_QUEUED);
 
 	mutex_unlock(&dev->v4l_lock);
 
@@ -306,7 +306,7 @@
 
 	stk1160_stop_hw(dev);
 
-	stk1160_clear_queue(dev);
+	stk1160_clear_queue(dev, VB2_BUF_STATE_ERROR);
 
 	stk1160_dbg("streaming stopped\n");
 
@@ -745,7 +745,7 @@
 /********************************************************************/
 
 /* Must be called with both v4l_lock and vb_queue_lock hold */
-void stk1160_clear_queue(struct stk1160 *dev)
+void stk1160_clear_queue(struct stk1160 *dev, enum vb2_buffer_state vb2_state)
 {
 	struct stk1160_buffer *buf;
 	unsigned long flags;
@@ -756,7 +756,7 @@
 		buf = list_first_entry(&dev->avail_bufs,
 			struct stk1160_buffer, list);
 		list_del(&buf->list);
-		vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
+		vb2_buffer_done(&buf->vb.vb2_buf, vb2_state);
 		stk1160_dbg("buffer [%p/%d] aborted\n",
 			    buf, buf->vb.vb2_buf.index);
 	}
@@ -766,7 +766,7 @@
 		buf = dev->isoc_ctl.buf;
 		dev->isoc_ctl.buf = NULL;
 
-		vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
+		vb2_buffer_done(&buf->vb.vb2_buf, vb2_state);
 		stk1160_dbg("buffer [%p/%d] aborted\n",
 			    buf, buf->vb.vb2_buf.index);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/stk1160/stk1160-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/stk1160/stk1160-video.c
@@ -99,7 +99,7 @@
 static inline
 void stk1160_copy_video(struct stk1160 *dev, u8 *src, int len)
 {
-	int linesdone, lineoff, lencopy;
+	int linesdone, lineoff, lencopy, offset;
 	int bytesperline = dev->width * 2;
 	struct stk1160_buffer *buf = dev->isoc_ctl.buf;
 	u8 *dst = buf->mem;
@@ -107,8 +107,7 @@
 
 	/*
 	 * TODO: These stk1160_dbg are very spammy!
-	 * We should 1) check why we are getting them
-	 * and 2) add ratelimit.
+	 * We should check why we are getting them.
 	 *
 	 * UPDATE: One of the reasons (the only one?) for getting these
 	 * is incorrect standard (mismatch between expected and configured).
@@ -140,8 +139,13 @@
 	 * Check if we have enough space left in the buffer.
 	 * In that case, we force loop exit after copy.
 	 */
-	if (lencopy > buf->bytesused - buf->length) {
-		lencopy = buf->bytesused - buf->length;
+	offset = dst - (u8 *)buf->mem;
+	if (offset > buf->length) {
+		dev_warn_ratelimited(dev->dev, "out of bounds offset\n");
+		return;
+	}
+	if (lencopy > buf->length - offset) {
+		lencopy = buf->length - offset;
 		remain = lencopy;
 	}
 
@@ -151,7 +155,7 @@
 
 	/* Let the bug hunt begin! sanity checks! */
 	if (lencopy < 0) {
-		stk1160_dbg("copy skipped: negative lencopy\n");
+		printk_ratelimited(KERN_DEBUG "copy skipped: negative lencopy\n");
 		return;
 	}
 
@@ -183,8 +187,13 @@
 		 * Check if we have enough space left in the buffer.
 		 * In that case, we force loop exit after copy.
 		 */
-		if (lencopy > buf->bytesused - buf->length) {
-			lencopy = buf->bytesused - buf->length;
+		offset = dst - (u8 *)buf->mem;
+		if (offset > buf->length) {
+			dev_warn_ratelimited(dev->dev, "offset out of bounds\n");
+			return;
+		}
+		if (lencopy > buf->length - offset) {
+			lencopy = buf->length - offset;
 			remain = lencopy;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/stk1160/stk1160.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/stk1160/stk1160.h
@@ -166,7 +166,7 @@
 int stk1160_vb2_setup(struct stk1160 *dev);
 int stk1160_video_register(struct stk1160 *dev);
 void stk1160_video_unregister(struct stk1160 *dev);
-void stk1160_clear_queue(struct stk1160 *dev);
+void stk1160_clear_queue(struct stk1160 *dev, enum vb2_buffer_state vb2_state);
 
 /* Provided by stk1160-video.c */
 int stk1160_alloc_isoc(struct stk1160 *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/tm6000/tm6000-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/tm6000/tm6000-video.c
@@ -852,8 +852,7 @@
 	struct tm6000_core *dev = ((struct tm6000_fh *)priv)->dev;
 
 	strscpy(cap->driver, "tm6000", sizeof(cap->driver));
-	strscpy(cap->card, "Trident TVMaster TM5600/6000/6010",
-		sizeof(cap->card));
+	strscpy(cap->card, "Trident TM5600/6000/6010", sizeof(cap->card));
 	usb_make_path(dev->udev, cap->bus_info, sizeof(cap->bus_info));
 	cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE |
 			    V4L2_CAP_DEVICE_CAPS;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/ttusb-dec/ttusb_dec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/ttusb-dec/ttusb_dec.c
@@ -327,7 +327,7 @@
 	result = mutex_lock_interruptible(&dec->usb_mutex);
 	if (result) {
 		printk("%s: Failed to lock usb mutex.\n", __func__);
-		goto err;
+		goto err_free;
 	}
 
 	b[0] = 0xaa;
@@ -349,7 +349,7 @@
 	if (result) {
 		printk("%s: command bulk message failed: error %d\n",
 		       __func__, result);
-		goto err;
+		goto err_mutex_unlock;
 	}
 
 	result = usb_bulk_msg(dec->udev, dec->result_pipe, b,
@@ -358,7 +358,7 @@
 	if (result) {
 		printk("%s: result bulk message failed: error %d\n",
 		       __func__, result);
-		goto err;
+		goto err_mutex_unlock;
 	} else {
 		if (debug) {
 			printk(KERN_DEBUG "%s: result: %*ph\n",
@@ -371,9 +371,9 @@
 			memcpy(cmd_result, &b[4], b[3]);
 	}
 
-err:
+err_mutex_unlock:
 	mutex_unlock(&dec->usb_mutex);
-
+err_free:
 	kfree(b);
 	return result;
 }
@@ -1544,8 +1544,7 @@
 	dvb_dmx_release(&dec->demux);
 	if (dec->fe) {
 		dvb_unregister_frontend(dec->fe);
-		if (dec->fe->ops.release)
-			dec->fe->ops.release(dec->fe);
+		dvb_frontend_detach(dec->fe);
 	}
 	dvb_unregister_adapter(&dec->adapter);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/usbtv/usbtv-video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/usbtv/usbtv-video.c
@@ -959,15 +959,8 @@
 
 void usbtv_video_free(struct usbtv *usbtv)
 {
-	mutex_lock(&usbtv->vb2q_lock);
-	mutex_lock(&usbtv->v4l2_lock);
-
-	usbtv_stop(usbtv);
 	vb2_video_unregister_device(&usbtv->vdev);
 	v4l2_device_disconnect(&usbtv->v4l2_dev);
 
-	mutex_unlock(&usbtv->v4l2_lock);
-	mutex_unlock(&usbtv->vb2q_lock);
-
 	v4l2_device_put(&usbtv->v4l2_dev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_ctrl.c
@@ -6,6 +6,7 @@
  *          Laurent Pinchart (laurent.pinchart@ideasonboard.com)
  */
 
+#include <asm/barrier.h>
 #include <linux/kernel.h>
 #include <linux/list.h>
 #include <linux/module.h>
@@ -357,6 +358,11 @@
 	},
 };
 
+static const u32 uvc_control_classes[] = {
+	V4L2_CID_CAMERA_CLASS,
+	V4L2_CID_USER_CLASS,
+};
+
 static const struct uvc_menu_info power_line_frequency_controls[] = {
 	{ 0, "Disabled" },
 	{ 1, "50 Hz" },
@@ -427,7 +433,6 @@
 static const struct uvc_control_mapping uvc_ctrl_mappings[] = {
 	{
 		.id		= V4L2_CID_BRIGHTNESS,
-		.name		= "Brightness",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_BRIGHTNESS_CONTROL,
 		.size		= 16,
@@ -437,7 +442,6 @@
 	},
 	{
 		.id		= V4L2_CID_CONTRAST,
-		.name		= "Contrast",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_CONTRAST_CONTROL,
 		.size		= 16,
@@ -447,7 +451,6 @@
 	},
 	{
 		.id		= V4L2_CID_HUE,
-		.name		= "Hue",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_HUE_CONTROL,
 		.size		= 16,
@@ -459,7 +462,6 @@
 	},
 	{
 		.id		= V4L2_CID_SATURATION,
-		.name		= "Saturation",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_SATURATION_CONTROL,
 		.size		= 16,
@@ -469,7 +471,6 @@
 	},
 	{
 		.id		= V4L2_CID_SHARPNESS,
-		.name		= "Sharpness",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_SHARPNESS_CONTROL,
 		.size		= 16,
@@ -479,7 +480,6 @@
 	},
 	{
 		.id		= V4L2_CID_GAMMA,
-		.name		= "Gamma",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_GAMMA_CONTROL,
 		.size		= 16,
@@ -489,7 +489,6 @@
 	},
 	{
 		.id		= V4L2_CID_BACKLIGHT_COMPENSATION,
-		.name		= "Backlight Compensation",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_BACKLIGHT_COMPENSATION_CONTROL,
 		.size		= 16,
@@ -499,7 +498,6 @@
 	},
 	{
 		.id		= V4L2_CID_GAIN,
-		.name		= "Gain",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_GAIN_CONTROL,
 		.size		= 16,
@@ -509,7 +507,6 @@
 	},
 	{
 		.id		= V4L2_CID_POWER_LINE_FREQUENCY,
-		.name		= "Power Line Frequency",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_POWER_LINE_FREQUENCY_CONTROL,
 		.size		= 2,
@@ -521,7 +518,6 @@
 	},
 	{
 		.id		= V4L2_CID_HUE_AUTO,
-		.name		= "Hue, Auto",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_HUE_AUTO_CONTROL,
 		.size		= 1,
@@ -532,7 +528,6 @@
 	},
 	{
 		.id		= V4L2_CID_EXPOSURE_AUTO,
-		.name		= "Exposure, Auto",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_AE_MODE_CONTROL,
 		.size		= 4,
@@ -545,7 +540,6 @@
 	},
 	{
 		.id		= V4L2_CID_EXPOSURE_AUTO_PRIORITY,
-		.name		= "Exposure, Auto Priority",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_AE_PRIORITY_CONTROL,
 		.size		= 1,
@@ -555,7 +549,6 @@
 	},
 	{
 		.id		= V4L2_CID_EXPOSURE_ABSOLUTE,
-		.name		= "Exposure (Absolute)",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_EXPOSURE_TIME_ABSOLUTE_CONTROL,
 		.size		= 32,
@@ -567,7 +560,6 @@
 	},
 	{
 		.id		= V4L2_CID_AUTO_WHITE_BALANCE,
-		.name		= "White Balance Temperature, Auto",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_WHITE_BALANCE_TEMPERATURE_AUTO_CONTROL,
 		.size		= 1,
@@ -578,7 +570,6 @@
 	},
 	{
 		.id		= V4L2_CID_WHITE_BALANCE_TEMPERATURE,
-		.name		= "White Balance Temperature",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_WHITE_BALANCE_TEMPERATURE_CONTROL,
 		.size		= 16,
@@ -590,7 +581,6 @@
 	},
 	{
 		.id		= V4L2_CID_AUTO_WHITE_BALANCE,
-		.name		= "White Balance Component, Auto",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_WHITE_BALANCE_COMPONENT_AUTO_CONTROL,
 		.size		= 1,
@@ -602,7 +592,6 @@
 	},
 	{
 		.id		= V4L2_CID_BLUE_BALANCE,
-		.name		= "White Balance Blue Component",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_WHITE_BALANCE_COMPONENT_CONTROL,
 		.size		= 16,
@@ -614,7 +603,6 @@
 	},
 	{
 		.id		= V4L2_CID_RED_BALANCE,
-		.name		= "White Balance Red Component",
 		.entity		= UVC_GUID_UVC_PROCESSING,
 		.selector	= UVC_PU_WHITE_BALANCE_COMPONENT_CONTROL,
 		.size		= 16,
@@ -626,7 +614,6 @@
 	},
 	{
 		.id		= V4L2_CID_FOCUS_ABSOLUTE,
-		.name		= "Focus (absolute)",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_FOCUS_ABSOLUTE_CONTROL,
 		.size		= 16,
@@ -638,7 +625,6 @@
 	},
 	{
 		.id		= V4L2_CID_FOCUS_AUTO,
-		.name		= "Focus, Auto",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_FOCUS_AUTO_CONTROL,
 		.size		= 1,
@@ -649,7 +635,6 @@
 	},
 	{
 		.id		= V4L2_CID_IRIS_ABSOLUTE,
-		.name		= "Iris, Absolute",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_IRIS_ABSOLUTE_CONTROL,
 		.size		= 16,
@@ -659,7 +644,6 @@
 	},
 	{
 		.id		= V4L2_CID_IRIS_RELATIVE,
-		.name		= "Iris, Relative",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_IRIS_RELATIVE_CONTROL,
 		.size		= 8,
@@ -669,7 +653,6 @@
 	},
 	{
 		.id		= V4L2_CID_ZOOM_ABSOLUTE,
-		.name		= "Zoom, Absolute",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_ZOOM_ABSOLUTE_CONTROL,
 		.size		= 16,
@@ -679,7 +662,6 @@
 	},
 	{
 		.id		= V4L2_CID_ZOOM_CONTINUOUS,
-		.name		= "Zoom, Continuous",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_ZOOM_RELATIVE_CONTROL,
 		.size		= 0,
@@ -691,7 +673,6 @@
 	},
 	{
 		.id		= V4L2_CID_PAN_ABSOLUTE,
-		.name		= "Pan (Absolute)",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_PANTILT_ABSOLUTE_CONTROL,
 		.size		= 32,
@@ -701,7 +682,6 @@
 	},
 	{
 		.id		= V4L2_CID_TILT_ABSOLUTE,
-		.name		= "Tilt (Absolute)",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_PANTILT_ABSOLUTE_CONTROL,
 		.size		= 32,
@@ -711,7 +691,6 @@
 	},
 	{
 		.id		= V4L2_CID_PAN_SPEED,
-		.name		= "Pan (Speed)",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_PANTILT_RELATIVE_CONTROL,
 		.size		= 16,
@@ -723,7 +702,6 @@
 	},
 	{
 		.id		= V4L2_CID_TILT_SPEED,
-		.name		= "Tilt (Speed)",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_PANTILT_RELATIVE_CONTROL,
 		.size		= 16,
@@ -735,7 +713,6 @@
 	},
 	{
 		.id		= V4L2_CID_PRIVACY,
-		.name		= "Privacy",
 		.entity		= UVC_GUID_UVC_CAMERA,
 		.selector	= UVC_CT_PRIVACY_CONTROL,
 		.size		= 1,
@@ -745,7 +722,6 @@
 	},
 	{
 		.id		= V4L2_CID_PRIVACY,
-		.name		= "Privacy",
 		.entity		= UVC_GUID_EXT_GPIO_CONTROLLER,
 		.selector	= UVC_CT_PRIVACY_CONTROL,
 		.size		= 1,
@@ -988,42 +964,181 @@
 	return value;
 }
 
+static int __uvc_ctrl_load_cur(struct uvc_video_chain *chain,
+			       struct uvc_control *ctrl)
+{
+	u8 *data;
+	int ret;
+
+	if (ctrl->loaded)
+		return 0;
+
+	data = uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT);
+
+	if ((ctrl->info.flags & UVC_CTRL_FLAG_GET_CUR) == 0) {
+		memset(data, 0, ctrl->info.size);
+		ctrl->loaded = 1;
+
+		return 0;
+	}
+
+	if (ctrl->entity->get_cur)
+		ret = ctrl->entity->get_cur(chain->dev, ctrl->entity,
+					    ctrl->info.selector, data,
+					    ctrl->info.size);
+	else
+		ret = uvc_query_ctrl(chain->dev, UVC_GET_CUR,
+				     ctrl->entity->id, chain->dev->intfnum,
+				     ctrl->info.selector, data,
+				     ctrl->info.size);
+
+	if (ret < 0)
+		return ret;
+
+	ctrl->loaded = 1;
+
+	return ret;
+}
+
 static int __uvc_ctrl_get(struct uvc_video_chain *chain,
-	struct uvc_control *ctrl, struct uvc_control_mapping *mapping,
-	s32 *value)
+			  struct uvc_control *ctrl,
+			  struct uvc_control_mapping *mapping,
+			  s32 *value)
 {
 	int ret;
 
 	if ((ctrl->info.flags & UVC_CTRL_FLAG_GET_CUR) == 0)
 		return -EACCES;
 
-	if (!ctrl->loaded) {
-		if (ctrl->entity->get_cur) {
-			ret = ctrl->entity->get_cur(chain->dev,
-				ctrl->entity,
-				ctrl->info.selector,
-				uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT),
-				ctrl->info.size);
-		} else {
-			ret = uvc_query_ctrl(chain->dev, UVC_GET_CUR,
-				ctrl->entity->id,
-				chain->dev->intfnum,
-				ctrl->info.selector,
-				uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT),
-				ctrl->info.size);
+	ret = __uvc_ctrl_load_cur(chain, ctrl);
+	if (ret < 0)
+		return ret;
+
+	*value = __uvc_ctrl_get_value(mapping,
+				uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT));
+
+	return 0;
+}
+
+static int __uvc_query_v4l2_class(struct uvc_video_chain *chain, u32 req_id,
+				  u32 found_id)
+{
+	bool find_next = req_id & V4L2_CTRL_FLAG_NEXT_CTRL;
+	unsigned int i;
+
+	req_id &= V4L2_CTRL_ID_MASK;
+
+	for (i = 0; i < ARRAY_SIZE(uvc_control_classes); i++) {
+		if (!(chain->ctrl_class_bitmap & BIT(i)))
+			continue;
+		if (!find_next) {
+			if (uvc_control_classes[i] == req_id)
+				return i;
+			continue;
 		}
-		if (ret < 0)
-			return ret;
+		if (uvc_control_classes[i] > req_id &&
+		    uvc_control_classes[i] < found_id)
+			return i;
+	}
 
-		ctrl->loaded = 1;
+	return -ENODEV;
+}
+
+static int uvc_query_v4l2_class(struct uvc_video_chain *chain, u32 req_id,
+				u32 found_id, struct v4l2_queryctrl *v4l2_ctrl)
+{
+	int idx;
+
+	idx = __uvc_query_v4l2_class(chain, req_id, found_id);
+	if (idx < 0)
+		return -ENODEV;
+
+	memset(v4l2_ctrl, 0, sizeof(*v4l2_ctrl));
+	v4l2_ctrl->id = uvc_control_classes[idx];
+	strscpy(v4l2_ctrl->name, v4l2_ctrl_get_name(v4l2_ctrl->id),
+		sizeof(v4l2_ctrl->name));
+	v4l2_ctrl->type = V4L2_CTRL_TYPE_CTRL_CLASS;
+	v4l2_ctrl->flags = V4L2_CTRL_FLAG_WRITE_ONLY
+			 | V4L2_CTRL_FLAG_READ_ONLY;
+	return 0;
+}
+
+/*
+ * Check if control @v4l2_id can be accessed by the given control @ioctl
+ * (VIDIOC_G_EXT_CTRLS, VIDIOC_TRY_EXT_CTRLS or VIDIOC_S_EXT_CTRLS).
+ *
+ * For set operations on slave controls, check if the master's value is set to
+ * manual, either in the others controls set in the same ioctl call, or from
+ * the master's current value. This catches VIDIOC_S_EXT_CTRLS calls that set
+ * both the master and slave control, such as for instance setting
+ * auto_exposure=1, exposure_time_absolute=251.
+ */
+int uvc_ctrl_is_accessible(struct uvc_video_chain *chain, u32 v4l2_id,
+			   const struct v4l2_ext_controls *ctrls,
+			   unsigned long ioctl)
+{
+	struct uvc_control_mapping *master_map = NULL;
+	struct uvc_control *master_ctrl = NULL;
+	struct uvc_control_mapping *mapping;
+	struct uvc_control *ctrl;
+	bool read = ioctl == VIDIOC_G_EXT_CTRLS;
+	s32 val;
+	int ret;
+	int i;
+
+	if (__uvc_query_v4l2_class(chain, v4l2_id, 0) >= 0)
+		return -EACCES;
+
+	ctrl = uvc_find_control(chain, v4l2_id, &mapping);
+	if (!ctrl)
+		return -EINVAL;
+
+	if (!(ctrl->info.flags & UVC_CTRL_FLAG_GET_CUR) && read)
+		return -EACCES;
+
+	if (!(ctrl->info.flags & UVC_CTRL_FLAG_SET_CUR) && !read)
+		return -EACCES;
+
+	if (ioctl != VIDIOC_S_EXT_CTRLS || !mapping->master_id)
+		return 0;
+
+	/*
+	 * Iterate backwards in cases where the master control is accessed
+	 * multiple times in the same ioctl. We want the last value.
+	 */
+	for (i = ctrls->count - 1; i >= 0; i--) {
+		if (ctrls->controls[i].id == mapping->master_id)
+			return ctrls->controls[i].value ==
+					mapping->master_manual ? 0 : -EACCES;
 	}
 
-	*value = __uvc_ctrl_get_value(mapping,
-				uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT));
+	__uvc_find_control(ctrl->entity, mapping->master_id, &master_map,
+			   &master_ctrl, 0);
+
+	if (!master_ctrl || !(master_ctrl->info.flags & UVC_CTRL_FLAG_GET_CUR))
+		return 0;
+
+	ret = __uvc_ctrl_get(chain, master_ctrl, master_map, &val);
+	if (ret >= 0 && val != mapping->master_manual)
+		return -EACCES;
 
 	return 0;
 }
 
+static const char *uvc_map_get_name(const struct uvc_control_mapping *map)
+{
+	const char *name;
+
+	if (map->name)
+		return map->name;
+
+	name = v4l2_ctrl_get_name(map->id);
+	if (name)
+		return name;
+
+	return "Unknown Control";
+}
+
 static int __uvc_query_v4l2_ctrl(struct uvc_video_chain *chain,
 	struct uvc_control *ctrl,
 	struct uvc_control_mapping *mapping,
@@ -1037,7 +1152,8 @@
 	memset(v4l2_ctrl, 0, sizeof(*v4l2_ctrl));
 	v4l2_ctrl->id = mapping->id;
 	v4l2_ctrl->type = mapping->v4l2_type;
-	strscpy(v4l2_ctrl->name, mapping->name, sizeof(v4l2_ctrl->name));
+	strscpy(v4l2_ctrl->name, uvc_map_get_name(mapping),
+		sizeof(v4l2_ctrl->name));
 	v4l2_ctrl->flags = 0;
 
 	if (!(ctrl->info.flags & UVC_CTRL_FLAG_GET_CUR))
@@ -1127,12 +1243,31 @@
 	if (ret < 0)
 		return -ERESTARTSYS;
 
+	/* Check if the ctrl is a know class */
+	if (!(v4l2_ctrl->id & V4L2_CTRL_FLAG_NEXT_CTRL)) {
+		ret = uvc_query_v4l2_class(chain, v4l2_ctrl->id, 0, v4l2_ctrl);
+		if (!ret)
+			goto done;
+	}
+
 	ctrl = uvc_find_control(chain, v4l2_ctrl->id, &mapping);
 	if (ctrl == NULL) {
 		ret = -EINVAL;
 		goto done;
 	}
 
+	/*
+	 * If we're enumerating control with V4L2_CTRL_FLAG_NEXT_CTRL, check if
+	 * a class should be inserted between the previous control and the one
+	 * we have just found.
+	 */
+	if (v4l2_ctrl->id & V4L2_CTRL_FLAG_NEXT_CTRL) {
+		ret = uvc_query_v4l2_class(chain, v4l2_ctrl->id, mapping->id,
+					   v4l2_ctrl);
+		if (!ret)
+			goto done;
+	}
+
 	ret = __uvc_query_v4l2_ctrl(chain, ctrl, mapping, v4l2_ctrl);
 done:
 	mutex_unlock(&chain->ctrl_mutex);
@@ -1282,6 +1417,40 @@
 	uvc_ctrl_send_event(chain, handle, ctrl, mapping, val, changes);
 }
 
+static void uvc_ctrl_set_handle(struct uvc_fh *handle, struct uvc_control *ctrl,
+				struct uvc_fh *new_handle)
+{
+	lockdep_assert_held(&handle->chain->ctrl_mutex);
+
+	if (new_handle) {
+		if (ctrl->handle)
+			dev_warn_ratelimited(&handle->stream->dev->udev->dev,
+					     "UVC non compliance: Setting an async control with a pending operation.");
+
+		if (new_handle == ctrl->handle)
+			return;
+
+		if (ctrl->handle) {
+			WARN_ON(!ctrl->handle->pending_async_ctrls);
+			if (ctrl->handle->pending_async_ctrls)
+				ctrl->handle->pending_async_ctrls--;
+		}
+
+		ctrl->handle = new_handle;
+		handle->pending_async_ctrls++;
+		return;
+	}
+
+	/* Cannot clear the handle for a control not owned by us.*/
+	if (WARN_ON(ctrl->handle != handle))
+		return;
+
+	ctrl->handle = NULL;
+	if (WARN_ON(!handle->pending_async_ctrls))
+		return;
+	handle->pending_async_ctrls--;
+}
+
 void uvc_ctrl_status_event(struct uvc_video_chain *chain,
 			   struct uvc_control *ctrl, const u8 *data)
 {
@@ -1292,7 +1461,8 @@
 	mutex_lock(&chain->ctrl_mutex);
 
 	handle = ctrl->handle;
-	ctrl->handle = NULL;
+	if (handle)
+		uvc_ctrl_set_handle(handle, ctrl, NULL);
 
 	list_for_each_entry(mapping, &ctrl->info.mappings, list) {
 		s32 value = __uvc_ctrl_get_value(mapping, data);
@@ -1325,6 +1495,10 @@
 
 	uvc_ctrl_status_event(w->chain, w->ctrl, w->data);
 
+	/* The barrier is needed to synchronize with uvc_status_stop(). */
+	if (smp_load_acquire(&dev->flush_status))
+		return;
+
 	/* Resubmit the URB. */
 	w->urb->interval = dev->int_ep->desc.bInterval;
 	ret = usb_submit_urb(w->urb, GFP_KERNEL);
@@ -1339,10 +1513,8 @@
 	struct uvc_device *dev = chain->dev;
 	struct uvc_ctrl_work *w = &dev->async_ctrl;
 
-	if (list_empty(&ctrl->info.mappings)) {
-		ctrl->handle = NULL;
+	if (list_empty(&ctrl->info.mappings))
 		return false;
-	}
 
 	w->data = data;
 	w->urb = urb;
@@ -1372,13 +1544,13 @@
 {
 	struct uvc_control_mapping *mapping;
 	struct uvc_control *ctrl;
-	u32 changes = V4L2_EVENT_CTRL_CH_VALUE;
 	unsigned int i;
 	unsigned int j;
 
 	for (i = 0; i < xctrls_count; ++i) {
-		ctrl = uvc_find_control(handle->chain, xctrls[i].id, &mapping);
+		u32 changes = V4L2_EVENT_CTRL_CH_VALUE;
 
+		ctrl = uvc_find_control(handle->chain, xctrls[i].id, &mapping);
 		if (ctrl->info.flags & UVC_CTRL_FLAG_ASYNCHRONOUS)
 			/* Notification will be sent from an Interrupt event. */
 			continue;
@@ -1426,6 +1598,11 @@
 	if (ret < 0)
 		return -ERESTARTSYS;
 
+	if (__uvc_query_v4l2_class(handle->chain, sev->id, 0) >= 0) {
+		ret = 0;
+		goto done;
+	}
+
 	ctrl = uvc_find_control(handle->chain, sev->id, &mapping);
 	if (ctrl == NULL) {
 		ret = -EINVAL;
@@ -1459,7 +1636,10 @@
 	struct uvc_fh *handle = container_of(sev->fh, struct uvc_fh, vfh);
 
 	mutex_lock(&handle->chain->ctrl_mutex);
+	if (__uvc_query_v4l2_class(handle->chain, sev->id, 0) >= 0)
+		goto done;
 	list_del(&sev->node);
+done:
 	mutex_unlock(&handle->chain->ctrl_mutex);
 }
 
@@ -1500,7 +1680,10 @@
 }
 
 static int uvc_ctrl_commit_entity(struct uvc_device *dev,
-	struct uvc_entity *entity, int rollback)
+				  struct uvc_fh *handle,
+				  struct uvc_entity *entity,
+				  int rollback,
+				  struct uvc_control **err_ctrl)
 {
 	struct uvc_control *ctrl;
 	unsigned int i;
@@ -1542,30 +1725,64 @@
 
 		ctrl->dirty = 0;
 
-		if (ret < 0)
+		if (ret < 0) {
+			if (err_ctrl)
+				*err_ctrl = ctrl;
 			return ret;
+		}
+
+		if (!rollback && handle &&
+		    ctrl->info.flags & UVC_CTRL_FLAG_ASYNCHRONOUS)
+			uvc_ctrl_set_handle(handle, ctrl, handle);
 	}
 
 	return 0;
 }
 
+static int uvc_ctrl_find_ctrl_idx(struct uvc_entity *entity,
+				  struct v4l2_ext_controls *ctrls,
+				  struct uvc_control *uvc_control)
+{
+	struct uvc_control_mapping *mapping = NULL;
+	struct uvc_control *ctrl_found = NULL;
+	unsigned int i;
+
+	if (!entity)
+		return ctrls->count;
+
+	for (i = 0; i < ctrls->count; i++) {
+		__uvc_find_control(entity, ctrls->controls[i].id, &mapping,
+				   &ctrl_found, 0);
+		if (uvc_control == ctrl_found)
+			return i;
+	}
+
+	return ctrls->count;
+}
+
 int __uvc_ctrl_commit(struct uvc_fh *handle, int rollback,
-		      const struct v4l2_ext_control *xctrls,
-		      unsigned int xctrls_count)
+		      struct v4l2_ext_controls *ctrls)
 {
 	struct uvc_video_chain *chain = handle->chain;
+	struct uvc_control *err_ctrl;
 	struct uvc_entity *entity;
 	int ret = 0;
 
 	/* Find the control. */
 	list_for_each_entry(entity, &chain->entities, chain) {
-		ret = uvc_ctrl_commit_entity(chain->dev, entity, rollback);
-		if (ret < 0)
+		ret = uvc_ctrl_commit_entity(chain->dev, handle, entity,
+					     rollback, &err_ctrl);
+		if (ret < 0) {
+			if (ctrls)
+				ctrls->error_idx =
+					uvc_ctrl_find_ctrl_idx(entity, ctrls,
+							       err_ctrl);
 			goto done;
+		}
 	}
 
 	if (!rollback)
-		uvc_ctrl_send_events(handle, xctrls, xctrls_count);
+		uvc_ctrl_send_events(handle, ctrls->controls, ctrls->count);
 done:
 	mutex_unlock(&chain->ctrl_mutex);
 	return ret;
@@ -1577,6 +1794,9 @@
 	struct uvc_control *ctrl;
 	struct uvc_control_mapping *mapping;
 
+	if (__uvc_query_v4l2_class(chain, xctrl->id, 0) >= 0)
+		return -EACCES;
+
 	ctrl = uvc_find_control(chain, xctrl->id, &mapping);
 	if (ctrl == NULL)
 		return -EINVAL;
@@ -1596,6 +1816,9 @@
 	s32 max;
 	int ret;
 
+	if (__uvc_query_v4l2_class(chain, xctrl->id, 0) >= 0)
+		return -EACCES;
+
 	ctrl = uvc_find_control(chain, xctrl->id, &mapping);
 	if (ctrl == NULL)
 		return -EINVAL;
@@ -1667,21 +1890,10 @@
 	 * needs to be loaded from the device to perform the read-modify-write
 	 * operation.
 	 */
-	if (!ctrl->loaded && (ctrl->info.size * 8) != mapping->size) {
-		if ((ctrl->info.flags & UVC_CTRL_FLAG_GET_CUR) == 0) {
-			memset(uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT),
-				0, ctrl->info.size);
-		} else {
-			ret = uvc_query_ctrl(chain->dev, UVC_GET_CUR,
-				ctrl->entity->id, chain->dev->intfnum,
-				ctrl->info.selector,
-				uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT),
-				ctrl->info.size);
-			if (ret < 0)
-				return ret;
-		}
-
-		ctrl->loaded = 1;
+	if ((ctrl->info.size * 8) != mapping->size) {
+		ret = __uvc_ctrl_load_cur(chain, ctrl);
+		if (ret < 0)
+			return ret;
 	}
 
 	/* Backup the current value in case we need to rollback later. */
@@ -1694,9 +1906,6 @@
 	mapping->set(mapping, value,
 		uvc_ctrl_data(ctrl, UVC_CTRL_DATA_CURRENT));
 
-	if (ctrl->info.flags & UVC_CTRL_FLAG_ASYNCHRONOUS)
-		ctrl->handle = handle;
-
 	ctrl->dirty = 1;
 	ctrl->modified = 1;
 	return 0;
@@ -1726,7 +1935,13 @@
 	else
 		ret = uvc_query_ctrl(dev, UVC_GET_INFO, ctrl->entity->id,
 				     dev->intfnum, info->selector, data, 1);
-	if (!ret)
+
+	if (!ret) {
+		info->flags &= ~(UVC_CTRL_FLAG_GET_CUR |
+				 UVC_CTRL_FLAG_SET_CUR |
+				 UVC_CTRL_FLAG_AUTO_UPDATE |
+				 UVC_CTRL_FLAG_ASYNCHRONOUS);
+
 		info->flags |= (data[0] & UVC_CONTROL_CAP_GET ?
 				UVC_CTRL_FLAG_GET_CUR : 0)
 			    |  (data[0] & UVC_CONTROL_CAP_SET ?
@@ -1735,6 +1950,7 @@
 				UVC_CTRL_FLAG_AUTO_UPDATE : 0)
 			    |  (data[0] & UVC_CONTROL_CAP_ASYNCHRONOUS ?
 				UVC_CTRL_FLAG_ASYNCHRONOUS : 0);
+	}
 
 	kfree(data);
 	return ret;
@@ -1862,7 +2078,7 @@
 int uvc_xu_ctrl_query(struct uvc_video_chain *chain,
 	struct uvc_xu_control_query *xqry)
 {
-	struct uvc_entity *entity;
+	struct uvc_entity *entity, *iter;
 	struct uvc_control *ctrl;
 	unsigned int i;
 	bool found;
@@ -1872,16 +2088,16 @@
 	int ret;
 
 	/* Find the extension unit. */
-	found = false;
-	list_for_each_entry(entity, &chain->entities, chain) {
-		if (UVC_ENTITY_TYPE(entity) == UVC_VC_EXTENSION_UNIT &&
-		    entity->id == xqry->unit) {
-			found = true;
+	entity = NULL;
+	list_for_each_entry(iter, &chain->entities, chain) {
+		if (UVC_ENTITY_TYPE(iter) == UVC_VC_EXTENSION_UNIT &&
+		    iter->id == xqry->unit) {
+			entity = iter;
 			break;
 		}
 	}
 
-	if (!found) {
+	if (!entity) {
 		uvc_dbg(chain->dev, CONTROL, "Extension unit %u not found\n",
 			xqry->unit);
 		return -ENOENT;
@@ -2018,7 +2234,7 @@
 			ctrl->dirty = 1;
 		}
 
-		ret = uvc_ctrl_commit_entity(dev, entity, 0);
+		ret = uvc_ctrl_commit_entity(dev, NULL, entity, 0, NULL);
 		if (ret < 0)
 			return ret;
 	}
@@ -2057,11 +2273,12 @@
 /*
  * Add a control mapping to a given control.
  */
-static int __uvc_ctrl_add_mapping(struct uvc_device *dev,
+static int __uvc_ctrl_add_mapping(struct uvc_video_chain *chain,
 	struct uvc_control *ctrl, const struct uvc_control_mapping *mapping)
 {
 	struct uvc_control_mapping *map;
 	unsigned int size;
+	unsigned int i;
 
 	/* Most mappings come from static kernel data and need to be duplicated.
 	 * Mappings that come from userspace will be unnecessarily duplicated,
@@ -2085,9 +2302,18 @@
 	if (map->set == NULL)
 		map->set = uvc_set_le_value;
 
+	for (i = 0; i < ARRAY_SIZE(uvc_control_classes); i++) {
+		if (V4L2_CTRL_ID2WHICH(uvc_control_classes[i]) ==
+						V4L2_CTRL_ID2WHICH(map->id)) {
+			chain->ctrl_class_bitmap |= BIT(i);
+			break;
+		}
+	}
+
 	list_add_tail(&map->list, &ctrl->info.mappings);
-	uvc_dbg(dev, CONTROL, "Adding mapping '%s' to control %pUl/%u\n",
-		map->name, ctrl->info.entity, ctrl->info.selector);
+	uvc_dbg(chain->dev, CONTROL, "Adding mapping '%s' to control %pUl/%u\n",
+		uvc_map_get_name(map), ctrl->info.entity,
+		ctrl->info.selector);
 
 	return 0;
 }
@@ -2105,7 +2331,7 @@
 	if (mapping->id & ~V4L2_CTRL_ID_MASK) {
 		uvc_dbg(dev, CONTROL,
 			"Can't add mapping '%s', control id 0x%08x is invalid\n",
-			mapping->name, mapping->id);
+			uvc_map_get_name(mapping), mapping->id);
 		return -EINVAL;
 	}
 
@@ -2152,7 +2378,7 @@
 		if (mapping->id == map->id) {
 			uvc_dbg(dev, CONTROL,
 				"Can't add mapping '%s', control id 0x%08x already exists\n",
-				mapping->name, mapping->id);
+				uvc_map_get_name(mapping), mapping->id);
 			ret = -EEXIST;
 			goto done;
 		}
@@ -2163,12 +2389,12 @@
 		atomic_dec(&dev->nmappings);
 		uvc_dbg(dev, CONTROL,
 			"Can't add mapping '%s', maximum mappings count (%u) exceeded\n",
-			mapping->name, UVC_MAX_CONTROL_MAPPINGS);
+			uvc_map_get_name(mapping), UVC_MAX_CONTROL_MAPPINGS);
 		ret = -ENOMEM;
 		goto done;
 	}
 
-	ret = __uvc_ctrl_add_mapping(dev, ctrl, mapping);
+	ret = __uvc_ctrl_add_mapping(chain, ctrl, mapping);
 	if (ret < 0)
 		atomic_dec(&dev->nmappings);
 
@@ -2244,7 +2470,8 @@
  * Add control information and hardcoded stock control mappings to the given
  * device.
  */
-static void uvc_ctrl_init_ctrl(struct uvc_device *dev, struct uvc_control *ctrl)
+static void uvc_ctrl_init_ctrl(struct uvc_video_chain *chain,
+			       struct uvc_control *ctrl)
 {
 	const struct uvc_control_info *info = uvc_ctrls;
 	const struct uvc_control_info *iend = info + ARRAY_SIZE(uvc_ctrls);
@@ -2263,14 +2490,14 @@
 	for (; info < iend; ++info) {
 		if (uvc_entity_match_guid(ctrl->entity, info->entity) &&
 		    ctrl->index == info->index) {
-			uvc_ctrl_add_info(dev, ctrl, info);
+			uvc_ctrl_add_info(chain->dev, ctrl, info);
 			/*
 			 * Retrieve control flags from the device. Ignore errors
 			 * and work with default flag values from the uvc_ctrl
 			 * array when the device doesn't properly implement
 			 * GET_INFO on standard controls.
 			 */
-			uvc_ctrl_get_flags(dev, ctrl, &ctrl->info);
+			uvc_ctrl_get_flags(chain->dev, ctrl, &ctrl->info);
 			break;
 		 }
 	}
@@ -2281,22 +2508,20 @@
 	for (; mapping < mend; ++mapping) {
 		if (uvc_entity_match_guid(ctrl->entity, mapping->entity) &&
 		    ctrl->info.selector == mapping->selector)
-			__uvc_ctrl_add_mapping(dev, ctrl, mapping);
+			__uvc_ctrl_add_mapping(chain, ctrl, mapping);
 	}
 }
 
 /*
  * Initialize device controls.
  */
-int uvc_ctrl_init_device(struct uvc_device *dev)
+static int uvc_ctrl_init_chain(struct uvc_video_chain *chain)
 {
 	struct uvc_entity *entity;
 	unsigned int i;
 
-	INIT_WORK(&dev->async_ctrl.work, uvc_ctrl_status_event_work);
-
 	/* Walk the entities list and instantiate controls */
-	list_for_each_entry(entity, &dev->entities, list) {
+	list_for_each_entry(entity, &chain->entities, chain) {
 		struct uvc_control *ctrl;
 		unsigned int bControlSize = 0, ncontrols;
 		u8 *bmControls = NULL;
@@ -2316,7 +2541,7 @@
 		}
 
 		/* Remove bogus/blacklisted controls */
-		uvc_ctrl_prune_entity(dev, entity);
+		uvc_ctrl_prune_entity(chain->dev, entity);
 
 		/* Count supported controls and allocate the controls array */
 		ncontrols = memweight(bmControls, bControlSize);
@@ -2338,7 +2563,7 @@
 			ctrl->entity = entity;
 			ctrl->index = i;
 
-			uvc_ctrl_init_ctrl(dev, ctrl);
+			uvc_ctrl_init_ctrl(chain, ctrl);
 			ctrl++;
 		}
 	}
@@ -2346,6 +2571,46 @@
 	return 0;
 }
 
+int uvc_ctrl_init_device(struct uvc_device *dev)
+{
+	struct uvc_video_chain *chain;
+	int ret;
+
+	INIT_WORK(&dev->async_ctrl.work, uvc_ctrl_status_event_work);
+
+	list_for_each_entry(chain, &dev->chains, list) {
+		ret = uvc_ctrl_init_chain(chain);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+void uvc_ctrl_cleanup_fh(struct uvc_fh *handle)
+{
+	struct uvc_entity *entity;
+
+	mutex_lock(&handle->chain->ctrl_mutex);
+
+	if (!handle->pending_async_ctrls) {
+		mutex_unlock(&handle->chain->ctrl_mutex);
+		return;
+	}
+
+	list_for_each_entry(entity, &handle->chain->dev->entities, list) {
+		unsigned int i;
+		for (i = 0; i < entity->ncontrols; ++i) {
+			if (entity->controls[i].handle != handle)
+				continue;
+			uvc_ctrl_set_handle(handle, &entity->controls[i], NULL);
+		}
+	}
+
+	WARN_ON(handle->pending_async_ctrls);
+	mutex_unlock(&handle->chain->ctrl_mutex);
+}
+
 /*
  * Cleanup device controls.
  */
@@ -2357,6 +2622,7 @@
 	list_for_each_entry_safe(mapping, nm, &ctrl->info.mappings, list) {
 		list_del(&mapping->list);
 		kfree(mapping->menu_info);
+		kfree(mapping->name);
 		kfree(mapping);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_driver.c
@@ -530,18 +530,17 @@
 		/* Find the format descriptor from its GUID. */
 		fmtdesc = uvc_format_by_guid(&buffer[5]);
 
-		if (fmtdesc != NULL) {
-			strscpy(format->name, fmtdesc->name,
-				sizeof(format->name));
-			format->fcc = fmtdesc->fcc;
-		} else {
+		if (!fmtdesc) {
+			/*
+			 * Unknown video formats are not fatal errors, the
+			 * caller will skip this descriptor.
+			 */
 			dev_info(&streaming->intf->dev,
 				 "Unknown video format %pUl\n", &buffer[5]);
-			snprintf(format->name, sizeof(format->name), "%pUl\n",
-				&buffer[5]);
-			format->fcc = 0;
+			return 0;
 		}
 
+		format->fcc = fmtdesc->fcc;
 		format->bpp = buffer[21];
 
 		/* Some devices report a format that doesn't match what they
@@ -549,8 +548,6 @@
 		 */
 		if (dev->quirks & UVC_QUIRK_FORCE_Y8) {
 			if (format->fcc == V4L2_PIX_FMT_YUYV) {
-				strscpy(format->name, "Greyscale 8-bit (Y8  )",
-					sizeof(format->name));
 				format->fcc = V4L2_PIX_FMT_GREY;
 				format->bpp = 8;
 				width_multiplier = 2;
@@ -591,7 +588,6 @@
 			return -EINVAL;
 		}
 
-		strscpy(format->name, "MJPEG", sizeof(format->name));
 		format->fcc = V4L2_PIX_FMT_MJPEG;
 		format->flags = UVC_FMT_FLAG_COMPRESSED;
 		format->bpp = 0;
@@ -607,17 +603,7 @@
 			return -EINVAL;
 		}
 
-		switch (buffer[8] & 0x7f) {
-		case 0:
-			strscpy(format->name, "SD-DV", sizeof(format->name));
-			break;
-		case 1:
-			strscpy(format->name, "SDL-DV", sizeof(format->name));
-			break;
-		case 2:
-			strscpy(format->name, "HD-DV", sizeof(format->name));
-			break;
-		default:
+		if ((buffer[8] & 0x7f) > 2) {
 			uvc_dbg(dev, DESCR,
 				"device %d videostreaming interface %d: unknown DV format %u\n",
 				dev->udev->devnum,
@@ -625,9 +611,6 @@
 			return -EINVAL;
 		}
 
-		strlcat(format->name, buffer[8] & (1 << 7) ? " 60Hz" : " 50Hz",
-			sizeof(format->name));
-
 		format->fcc = V4L2_PIX_FMT_DV;
 		format->flags = UVC_FMT_FLAG_COMPRESSED | UVC_FMT_FLAG_STREAM;
 		format->bpp = 0;
@@ -654,7 +637,7 @@
 		return -EINVAL;
 	}
 
-	uvc_dbg(dev, DESCR, "Found format %s\n", format->name);
+	uvc_dbg(dev, DESCR, "Found format %p4cc", &format->fcc);
 
 	buflen -= buffer[0];
 	buffer += buffer[0];
@@ -662,7 +645,7 @@
 	/* Parse the frame descriptors. Only uncompressed, MJPEG and frame
 	 * based formats have frame descriptors.
 	 */
-	while (buflen > 2 && buffer[1] == USB_DT_CS_INTERFACE &&
+	while (ftype && buflen > 2 && buffer[1] == USB_DT_CS_INTERFACE &&
 	       buffer[2] == ftype) {
 		frame = &format->frame[format->nframes];
 		if (ftype != UVC_VS_FRAME_FRAME_BASED)
@@ -953,19 +936,29 @@
 		goto error;
 	}
 
-	size = nformats * sizeof(*format) + nframes * sizeof(*frame)
+	/*
+	 * Allocate memory for the formats, the frames and the intervals,
+	 * plus any required padding to guarantee that everything has the
+	 * correct alignment.
+	 */
+	size = nformats * sizeof(*format);
+	size = ALIGN(size, __alignof__(*frame)) + nframes * sizeof(*frame);
+	size = ALIGN(size, __alignof__(*interval))
 	     + nintervals * sizeof(*interval);
+
 	format = kzalloc(size, GFP_KERNEL);
-	if (format == NULL) {
+	if (!format) {
 		ret = -ENOMEM;
 		goto error;
 	}
 
-	frame = (struct uvc_frame *)&format[nformats];
-	interval = (u32 *)&frame[nframes];
+	frame = (void *)format + nformats * sizeof(*format);
+	frame = PTR_ALIGN(frame, __alignof__(*frame));
+	interval = (void *)frame + nframes * sizeof(*frame);
+	interval = PTR_ALIGN(interval, __alignof__(*interval));
 
 	streaming->format = format;
-	streaming->nformats = nformats;
+	streaming->nformats = 0;
 
 	/* Parse the format descriptors. */
 	while (buflen > 2 && buffer[1] == USB_DT_CS_INTERFACE) {
@@ -979,7 +972,10 @@
 				&interval, buffer, buflen);
 			if (ret < 0)
 				goto error;
+			if (!ret)
+				break;
 
+			streaming->nformats++;
 			frame += format->nframes;
 			format++;
 
@@ -1151,10 +1147,8 @@
 					       + n;
 		memcpy(unit->extension.bmControls, &buffer[23+p], 2*n);
 
-		if (buffer[24+p+2*n] != 0)
-			usb_string(udev, buffer[24+p+2*n], unit->name,
-				   sizeof(unit->name));
-		else
+		if (buffer[24+p+2*n] == 0 ||
+		    usb_string(udev, buffer[24+p+2*n], unit->name, sizeof(unit->name)) < 0)
 			sprintf(unit->name, "Extension %u", buffer[3]);
 
 		list_add_tail(&unit->list, &dev->entities);
@@ -1278,15 +1272,15 @@
 			memcpy(term->media.bmTransportModes, &buffer[10+n], p);
 		}
 
-		if (buffer[7] != 0)
-			usb_string(udev, buffer[7], term->name,
-				   sizeof(term->name));
-		else if (UVC_ENTITY_TYPE(term) == UVC_ITT_CAMERA)
-			sprintf(term->name, "Camera %u", buffer[3]);
-		else if (UVC_ENTITY_TYPE(term) == UVC_ITT_MEDIA_TRANSPORT_INPUT)
-			sprintf(term->name, "Media %u", buffer[3]);
-		else
-			sprintf(term->name, "Input %u", buffer[3]);
+		if (buffer[7] == 0 ||
+		    usb_string(udev, buffer[7], term->name, sizeof(term->name)) < 0) {
+			if (UVC_ENTITY_TYPE(term) == UVC_ITT_CAMERA)
+				sprintf(term->name, "Camera %u", buffer[3]);
+			if (UVC_ENTITY_TYPE(term) == UVC_ITT_MEDIA_TRANSPORT_INPUT)
+				sprintf(term->name, "Media %u", buffer[3]);
+			else
+				sprintf(term->name, "Input %u", buffer[3]);
+		}
 
 		list_add_tail(&term->list, &dev->entities);
 		break;
@@ -1318,10 +1312,8 @@
 
 		memcpy(term->baSourceID, &buffer[7], 1);
 
-		if (buffer[8] != 0)
-			usb_string(udev, buffer[8], term->name,
-				   sizeof(term->name));
-		else
+		if (buffer[8] == 0 ||
+		    usb_string(udev, buffer[8], term->name, sizeof(term->name)) < 0)
 			sprintf(term->name, "Output %u", buffer[3]);
 
 		list_add_tail(&term->list, &dev->entities);
@@ -1343,10 +1335,8 @@
 
 		memcpy(unit->baSourceID, &buffer[5], p);
 
-		if (buffer[5+p] != 0)
-			usb_string(udev, buffer[5+p], unit->name,
-				   sizeof(unit->name));
-		else
+		if (buffer[5+p] == 0 ||
+		    usb_string(udev, buffer[5+p], unit->name, sizeof(unit->name)) < 0)
 			sprintf(unit->name, "Selector %u", buffer[3]);
 
 		list_add_tail(&unit->list, &dev->entities);
@@ -1376,10 +1366,8 @@
 		if (dev->uvc_version >= 0x0110)
 			unit->processing.bmVideoStandards = buffer[9+n];
 
-		if (buffer[8+n] != 0)
-			usb_string(udev, buffer[8+n], unit->name,
-				   sizeof(unit->name));
-		else
+		if (buffer[8+n] == 0 ||
+		    usb_string(udev, buffer[8+n], unit->name, sizeof(unit->name)) < 0)
 			sprintf(unit->name, "Processing %u", buffer[3]);
 
 		list_add_tail(&unit->list, &dev->entities);
@@ -1407,10 +1395,8 @@
 		unit->extension.bmControls = (u8 *)unit + sizeof(*unit);
 		memcpy(unit->extension.bmControls, &buffer[23+p], n);
 
-		if (buffer[23+p+n] != 0)
-			usb_string(udev, buffer[23+p+n], unit->name,
-				   sizeof(unit->name));
-		else
+		if (buffer[23+p+n] == 0 ||
+		    usb_string(udev, buffer[23+p+n], unit->name, sizeof(unit->name)) < 0)
 			sprintf(unit->name, "Extension %u", buffer[3]);
 
 		list_add_tail(&unit->list, &dev->entities);
@@ -1529,23 +1515,20 @@
 	struct gpio_desc *gpio_privacy;
 	int irq;
 
-	gpio_privacy = devm_gpiod_get_optional(&dev->udev->dev, "privacy",
+	gpio_privacy = devm_gpiod_get_optional(&dev->intf->dev, "privacy",
 					       GPIOD_IN);
 	if (IS_ERR_OR_NULL(gpio_privacy))
 		return PTR_ERR_OR_ZERO(gpio_privacy);
 
+	irq = gpiod_to_irq(gpio_privacy);
+	if (irq < 0)
+		return dev_err_probe(&dev->intf->dev, irq,
+				     "No IRQ for privacy GPIO\n");
+
 	unit = uvc_alloc_entity(UVC_EXT_GPIO_UNIT, UVC_EXT_GPIO_UNIT_ID, 0, 1);
 	if (!unit)
 		return -ENOMEM;
 
-	irq = gpiod_to_irq(gpio_privacy);
-	if (irq < 0) {
-		if (irq != EPROBE_DEFER)
-			dev_err(&dev->udev->dev,
-				"No IRQ for privacy GPIO (%d)\n", irq);
-		return irq;
-	}
-
 	unit->gpio.gpio_privacy = gpio_privacy;
 	unit->gpio.irq = irq;
 	unit->gpio.bControlSize = 1;
@@ -1565,15 +1548,27 @@
 static int uvc_gpio_init_irq(struct uvc_device *dev)
 {
 	struct uvc_entity *unit = dev->gpio_unit;
+	int ret;
 
 	if (!unit || unit->gpio.irq < 0)
 		return 0;
 
-	return devm_request_threaded_irq(&dev->udev->dev, unit->gpio.irq, NULL,
-					 uvc_gpio_irq,
-					 IRQF_ONESHOT | IRQF_TRIGGER_FALLING |
-					 IRQF_TRIGGER_RISING,
-					 "uvc_privacy_gpio", dev);
+	ret = request_threaded_irq(unit->gpio.irq, NULL, uvc_gpio_irq,
+				   IRQF_ONESHOT | IRQF_TRIGGER_FALLING |
+				   IRQF_TRIGGER_RISING,
+				   "uvc_privacy_gpio", dev);
+
+	unit->gpio.initialized = !ret;
+
+	return ret;
+}
+
+static void uvc_gpio_deinit(struct uvc_device *dev)
+{
+	if (!dev->gpio_unit || !dev->gpio_unit->gpio.initialized)
+		return;
+
+	free_irq(dev->gpio_unit->gpio.irq, dev);
 }
 
 /* ------------------------------------------------------------------------
@@ -2166,12 +2161,44 @@
 {
 	struct uvc_streaming *stream;
 
+	uvc_gpio_deinit(dev);
+
 	list_for_each_entry(stream, &dev->streams, list) {
+		/* Nothing to do here, continue. */
 		if (!video_is_registered(&stream->vdev))
 			continue;
 
+		/*
+		 * For stream->vdev we follow the same logic as:
+		 * vb2_video_unregister_device().
+		 */
+
+		/* 1. Take a reference to vdev */
+		get_device(&stream->vdev.dev);
+
+		/* 2. Ensure that no new ioctls can be called. */
 		video_unregister_device(&stream->vdev);
-		video_unregister_device(&stream->meta.vdev);
+
+		/* 3. Wait for old ioctls to finish. */
+		mutex_lock(&stream->mutex);
+
+		/* 4. Stop streaming. */
+		uvc_queue_release(&stream->queue);
+
+		mutex_unlock(&stream->mutex);
+
+		put_device(&stream->vdev.dev);
+
+		/*
+		 * For stream->meta.vdev we can directly call:
+		 * vb2_video_unregister_device().
+		 */
+		vb2_video_unregister_device(&stream->meta.vdev);
+
+		/*
+		 * Now both vdevs are not streaming and all the ioctls will
+		 * return -ENODEV.
+		 */
 
 		uvc_debugfs_cleanup_stream(stream);
 	}
@@ -2455,14 +2482,14 @@
 	if (v4l2_device_register(&intf->dev, &dev->vdev) < 0)
 		goto error;
 
-	/* Initialize controls. */
-	if (uvc_ctrl_init_device(dev) < 0)
-		goto error;
-
 	/* Scan the device for video chains. */
 	if (uvc_scan_device(dev) < 0)
 		goto error;
 
+	/* Initialize controls. */
+	if (uvc_ctrl_init_device(dev) < 0)
+		goto error;
+
 	/* Register video device nodes. */
 	if (uvc_register_chains(dev) < 0)
 		goto error;
@@ -2667,6 +2694,8 @@
  * The Logitech cameras listed below have their interface class set to
  * VENDOR_SPEC because they don't announce themselves as UVC devices, even
  * though they are compliant.
+ *
+ * Sort these by vendor/product ID.
  */
 static const struct usb_device_id uvc_ids[] = {
 	/* LogiLink Wireless Webcam */
@@ -2714,6 +2743,24 @@
 	  .bInterfaceSubClass	= 1,
 	  .bInterfaceProtocol	= 0,
 	  .driver_info		= (kernel_ulong_t)&uvc_quirk_probe_minmax },
+	/* Logitech, Webcam C910 */
+	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
+				| USB_DEVICE_ID_MATCH_INT_INFO,
+	  .idVendor		= 0x046d,
+	  .idProduct		= 0x0821,
+	  .bInterfaceClass	= USB_CLASS_VIDEO,
+	  .bInterfaceSubClass	= 1,
+	  .bInterfaceProtocol	= 0,
+	  .driver_info		= UVC_INFO_QUIRK(UVC_QUIRK_WAKE_AUTOSUSPEND)},
+	/* Logitech, Webcam B910 */
+	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
+				| USB_DEVICE_ID_MATCH_INT_INFO,
+	  .idVendor		= 0x046d,
+	  .idProduct		= 0x0823,
+	  .bInterfaceClass	= USB_CLASS_VIDEO,
+	  .bInterfaceSubClass	= 1,
+	  .bInterfaceProtocol	= 0,
+	  .driver_info		= UVC_INFO_QUIRK(UVC_QUIRK_WAKE_AUTOSUSPEND)},
 	/* Logitech Quickcam Fusion */
 	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
 				| USB_DEVICE_ID_MATCH_INT_INFO,
@@ -3128,6 +3175,15 @@
 	  .bInterfaceProtocol	= 0,
 	  .driver_info		= UVC_INFO_QUIRK(UVC_QUIRK_PROBE_MINMAX
 					| UVC_QUIRK_IGNORE_SELECTOR_UNIT) },
+	/* NXP Semiconductors IR VIDEO */
+	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
+				| USB_DEVICE_ID_MATCH_INT_INFO,
+	  .idVendor		= 0x1fc9,
+	  .idProduct		= 0x009b,
+	  .bInterfaceClass	= USB_CLASS_VIDEO,
+	  .bInterfaceSubClass	= 1,
+	  .bInterfaceProtocol	= 0,
+	  .driver_info		= (kernel_ulong_t)&uvc_quirk_probe_minmax },
 	/* Oculus VR Positional Tracker DK2 */
 	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
 				| USB_DEVICE_ID_MATCH_INT_INFO,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_entity.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_entity.c
@@ -37,7 +37,7 @@
 			continue;
 
 		remote = uvc_entity_by_id(chain->dev, entity->baSourceID[i]);
-		if (remote == NULL)
+		if (remote == NULL || remote->num_pads == 0)
 			return -EINVAL;
 
 		source = (UVC_ENTITY_TYPE(remote) == UVC_TT_STREAMING)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_queue.c
@@ -180,14 +180,27 @@
 static void uvc_stop_streaming(struct vb2_queue *vq)
 {
 	struct uvc_video_queue *queue = vb2_get_drv_priv(vq);
+	struct uvc_streaming *stream = uvc_queue_to_stream(queue);
 
 	lockdep_assert_irqs_enabled();
 
+	/* Prevent new buffers coming in. */
+	spin_lock_irq(&queue->irqlock);
+	queue->flags |= UVC_QUEUE_STOPPING;
+	spin_unlock_irq(&queue->irqlock);
+
+	/*
+	 * All pending work should be completed before disabling the stream, as
+	 * all URBs will be free'd during uvc_video_enable(s, 0).
+	 */
+	flush_workqueue(stream->async_wq);
+
 	if (vq->type != V4L2_BUF_TYPE_META_CAPTURE)
 		uvc_video_stop_streaming(uvc_queue_to_stream(queue));
 
 	spin_lock_irq(&queue->irqlock);
 	uvc_queue_return_buffers(queue, UVC_BUF_STATE_ERROR);
+	queue->flags &= ~UVC_QUEUE_STOPPING;
 	spin_unlock_irq(&queue->irqlock);
 }
 
@@ -481,7 +494,8 @@
 
 	buf->state = buf->error ? UVC_BUF_STATE_ERROR : UVC_BUF_STATE_DONE;
 	vb2_set_plane_payload(&buf->buf.vb2_buf, 0, buf->bytesused);
-	vb2_buffer_done(&buf->buf.vb2_buf, VB2_BUF_STATE_DONE);
+	vb2_buffer_done(&buf->buf.vb2_buf, buf->error ? VB2_BUF_STATE_ERROR :
+							VB2_BUF_STATE_DONE);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_status.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_status.c
@@ -6,6 +6,7 @@
  *          Laurent Pinchart (laurent.pinchart@ideasonboard.com)
  */
 
+#include <asm/barrier.h>
 #include <linux/kernel.h>
 #include <linux/input.h>
 #include <linux/slab.h>
@@ -267,6 +268,7 @@
 	dev->int_urb = usb_alloc_urb(0, GFP_KERNEL);
 	if (dev->int_urb == NULL) {
 		kfree(dev->status);
+		dev->status = NULL;
 		return -ENOMEM;
 	}
 
@@ -309,5 +311,41 @@
 
 void uvc_status_stop(struct uvc_device *dev)
 {
+	struct uvc_ctrl_work *w = &dev->async_ctrl;
+
+	/*
+	 * Prevent the asynchronous control handler from requeing the URB. The
+	 * barrier is needed so the flush_status change is visible to other
+	 * CPUs running the asynchronous handler before usb_kill_urb() is
+	 * called below.
+	 */
+	smp_store_release(&dev->flush_status, true);
+
+	/*
+	 * Cancel any pending asynchronous work. If any status event was queued,
+	 * process it synchronously.
+	 */
+	if (cancel_work_sync(&w->work))
+		uvc_ctrl_status_event(w->chain, w->ctrl, w->data);
+
+	/* Kill the urb. */
 	usb_kill_urb(dev->int_urb);
+
+	/*
+	 * The URB completion handler may have queued asynchronous work. This
+	 * won't resubmit the URB as flush_status is set, but it needs to be
+	 * cancelled before returning or it could then race with a future
+	 * uvc_status_start() call.
+	 */
+	if (cancel_work_sync(&w->work))
+		uvc_ctrl_status_event(w->chain, w->ctrl, w->data);
+
+	/*
+	 * From this point, there are no events on the queue and the status URB
+	 * is dead. No events will be queued until uvc_status_start() is called.
+	 * The barrier is needed to make sure that flush_status is visible to
+	 * uvc_ctrl_status_event_work() when uvc_status_start() will be called
+	 * again.
+	 */
+	smp_store_release(&dev->flush_status, false);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_v4l2.c
@@ -40,7 +40,15 @@
 		return -ENOMEM;
 
 	map->id = xmap->id;
-	memcpy(map->name, xmap->name, sizeof(map->name));
+	/* Non standard control id. */
+	if (v4l2_ctrl_get_name(map->id) == NULL) {
+		map->name = kmemdup(xmap->name, sizeof(xmap->name),
+				    GFP_KERNEL);
+		if (!map->name) {
+			ret = -ENOMEM;
+			goto free_map;
+		}
+	}
 	memcpy(map->entity, xmap->entity, sizeof(map->entity));
 	map->selector = xmap->selector;
 	map->size = xmap->size;
@@ -472,10 +480,13 @@
 	uvc_simplify_fraction(&timeperframe.numerator,
 		&timeperframe.denominator, 8, 333);
 
-	if (parm->type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
+	if (parm->type == V4L2_BUF_TYPE_VIDEO_CAPTURE) {
 		parm->parm.capture.timeperframe = timeperframe;
-	else
+		parm->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	} else {
 		parm->parm.output.timeperframe = timeperframe;
+		parm->parm.output.capability = V4L2_CAP_TIMEPERFRAME;
+	}
 
 	return 0;
 }
@@ -591,6 +602,8 @@
 
 	uvc_dbg(stream->dev, CALLS, "%s\n", __func__);
 
+	uvc_ctrl_cleanup_fh(handle);
+
 	/* Only free resources if this is a privileged handle. */
 	if (uvc_has_privileges(handle))
 		uvc_queue_release(&stream->queue);
@@ -646,8 +659,6 @@
 	fmt->flags = 0;
 	if (format->flags & UVC_FMT_FLAG_COMPRESSED)
 		fmt->flags |= V4L2_FMT_FLAG_COMPRESSED;
-	strscpy(fmt->description, format->name, sizeof(fmt->description));
-	fmt->description[sizeof(fmt->description) - 1] = 0;
 	fmt->pixelformat = format->fcc;
 	return 0;
 }
@@ -861,29 +872,31 @@
 	struct uvc_video_chain *chain = handle->chain;
 	const struct uvc_entity *selector = chain->selector;
 	struct uvc_entity *iterm = NULL;
+	struct uvc_entity *it;
 	u32 index = input->index;
-	int pin = 0;
 
 	if (selector == NULL ||
 	    (chain->dev->quirks & UVC_QUIRK_IGNORE_SELECTOR_UNIT)) {
 		if (index != 0)
 			return -EINVAL;
-		list_for_each_entry(iterm, &chain->entities, chain) {
-			if (UVC_ENTITY_IS_ITERM(iterm))
+		list_for_each_entry(it, &chain->entities, chain) {
+			if (UVC_ENTITY_IS_ITERM(it)) {
+				iterm = it;
 				break;
+			}
 		}
-		pin = iterm->id;
 	} else if (index < selector->bNrInPins) {
-		pin = selector->baSourceID[index];
-		list_for_each_entry(iterm, &chain->entities, chain) {
-			if (!UVC_ENTITY_IS_ITERM(iterm))
+		list_for_each_entry(it, &chain->entities, chain) {
+			if (!UVC_ENTITY_IS_ITERM(it))
 				continue;
-			if (iterm->id == pin)
+			if (it->id == selector->baSourceID[index]) {
+				iterm = it;
 				break;
+			}
 		}
 	}
 
-	if (iterm == NULL || iterm->id != pin)
+	if (iterm == NULL)
 		return -EINVAL;
 
 	memset(input, 0, sizeof(*input));
@@ -995,58 +1008,23 @@
 	return 0;
 }
 
-static int uvc_ioctl_g_ctrl(struct file *file, void *fh,
-			    struct v4l2_control *ctrl)
-{
-	struct uvc_fh *handle = fh;
-	struct uvc_video_chain *chain = handle->chain;
-	struct v4l2_ext_control xctrl;
-	int ret;
-
-	memset(&xctrl, 0, sizeof(xctrl));
-	xctrl.id = ctrl->id;
-
-	ret = uvc_ctrl_begin(chain);
-	if (ret < 0)
-		return ret;
-
-	ret = uvc_ctrl_get(chain, &xctrl);
-	uvc_ctrl_rollback(handle);
-	if (ret < 0)
-		return ret;
-
-	ctrl->value = xctrl.value;
-	return 0;
-}
-
-static int uvc_ioctl_s_ctrl(struct file *file, void *fh,
-			    struct v4l2_control *ctrl)
+static int uvc_ctrl_check_access(struct uvc_video_chain *chain,
+				 struct v4l2_ext_controls *ctrls,
+				 unsigned long ioctl)
 {
-	struct uvc_fh *handle = fh;
-	struct uvc_video_chain *chain = handle->chain;
-	struct v4l2_ext_control xctrl;
-	int ret;
-
-	memset(&xctrl, 0, sizeof(xctrl));
-	xctrl.id = ctrl->id;
-	xctrl.value = ctrl->value;
-
-	ret = uvc_ctrl_begin(chain);
-	if (ret < 0)
-		return ret;
+	struct v4l2_ext_control *ctrl = ctrls->controls;
+	unsigned int i;
+	int ret = 0;
 
-	ret = uvc_ctrl_set(handle, &xctrl);
-	if (ret < 0) {
-		uvc_ctrl_rollback(handle);
-		return ret;
+	for (i = 0; i < ctrls->count; ++ctrl, ++i) {
+		ret = uvc_ctrl_is_accessible(chain, ctrl->id, ctrls, ioctl);
+		if (ret)
+			break;
 	}
 
-	ret = uvc_ctrl_commit(handle, &xctrl, 1);
-	if (ret < 0)
-		return ret;
+	ctrls->error_idx = ioctl == VIDIOC_TRY_EXT_CTRLS ? i : ctrls->count;
 
-	ctrl->value = xctrl.value;
-	return 0;
+	return ret;
 }
 
 static int uvc_ioctl_g_ext_ctrls(struct file *file, void *fh,
@@ -1058,6 +1036,10 @@
 	unsigned int i;
 	int ret;
 
+	ret = uvc_ctrl_check_access(chain, ctrls, VIDIOC_G_EXT_CTRLS);
+	if (ret < 0)
+		return ret;
+
 	if (ctrls->which == V4L2_CTRL_WHICH_DEF_VAL) {
 		for (i = 0; i < ctrls->count; ++ctrl, ++i) {
 			struct v4l2_queryctrl qc = { .id = ctrl->id };
@@ -1094,16 +1076,16 @@
 
 static int uvc_ioctl_s_try_ext_ctrls(struct uvc_fh *handle,
 				     struct v4l2_ext_controls *ctrls,
-				     bool commit)
+				     unsigned long ioctl)
 {
 	struct v4l2_ext_control *ctrl = ctrls->controls;
 	struct uvc_video_chain *chain = handle->chain;
 	unsigned int i;
 	int ret;
 
-	/* Default value cannot be changed */
-	if (ctrls->which == V4L2_CTRL_WHICH_DEF_VAL)
-		return -EINVAL;
+	ret = uvc_ctrl_check_access(chain, ctrls, ioctl);
+	if (ret < 0)
+		return ret;
 
 	ret = uvc_ctrl_begin(chain);
 	if (ret < 0)
@@ -1113,15 +1095,16 @@
 		ret = uvc_ctrl_set(handle, ctrl);
 		if (ret < 0) {
 			uvc_ctrl_rollback(handle);
-			ctrls->error_idx = commit ? ctrls->count : i;
+			ctrls->error_idx = ioctl == VIDIOC_S_EXT_CTRLS ?
+						    ctrls->count : i;
 			return ret;
 		}
 	}
 
 	ctrls->error_idx = 0;
 
-	if (commit)
-		return uvc_ctrl_commit(handle, ctrls->controls, ctrls->count);
+	if (ioctl == VIDIOC_S_EXT_CTRLS)
+		return uvc_ctrl_commit(handle, ctrls);
 	else
 		return uvc_ctrl_rollback(handle);
 }
@@ -1131,7 +1114,7 @@
 {
 	struct uvc_fh *handle = fh;
 
-	return uvc_ioctl_s_try_ext_ctrls(handle, ctrls, true);
+	return uvc_ioctl_s_try_ext_ctrls(handle, ctrls, VIDIOC_S_EXT_CTRLS);
 }
 
 static int uvc_ioctl_try_ext_ctrls(struct file *file, void *fh,
@@ -1139,7 +1122,7 @@
 {
 	struct uvc_fh *handle = fh;
 
-	return uvc_ioctl_s_try_ext_ctrls(handle, ctrls, false);
+	return uvc_ioctl_s_try_ext_ctrls(handle, ctrls, VIDIOC_TRY_EXT_CTRLS);
 }
 
 static int uvc_ioctl_querymenu(struct file *file, void *fh,
@@ -1538,8 +1521,6 @@
 	.vidioc_s_input = uvc_ioctl_s_input,
 	.vidioc_queryctrl = uvc_ioctl_queryctrl,
 	.vidioc_query_ext_ctrl = uvc_ioctl_query_ext_ctrl,
-	.vidioc_g_ctrl = uvc_ioctl_g_ctrl,
-	.vidioc_s_ctrl = uvc_ioctl_s_ctrl,
 	.vidioc_g_ext_ctrls = uvc_ioctl_g_ext_ctrls,
 	.vidioc_s_ext_ctrls = uvc_ioctl_s_ext_ctrls,
 	.vidioc_try_ext_ctrls = uvc_ioctl_try_ext_ctrls,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvc_video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvc_video.c
@@ -115,6 +115,11 @@
 	case 5: /* Invalid unit */
 	case 6: /* Invalid control */
 	case 7: /* Invalid Request */
+		/*
+		 * The firmware has not properly implemented
+		 * the control or there has been a HW error.
+		 */
+		return -EIO;
 	case 8: /* Invalid value within range */
 		return -EINVAL;
 	default: /* reserved or unknown */
@@ -205,13 +210,13 @@
 		/* Compute a bandwidth estimation by multiplying the frame
 		 * size by the number of video frames per second, divide the
 		 * result by the number of USB frames (or micro-frames for
-		 * high-speed devices) per second and add the UVC header size
-		 * (assumed to be 12 bytes long).
+		 * high- and super-speed devices) per second and add the UVC
+		 * header size (assumed to be 12 bytes long).
 		 */
 		bandwidth = frame->wWidth * frame->wHeight / 8 * format->bpp;
 		bandwidth *= 10000000 / interval + 1;
 		bandwidth /= 1000;
-		if (stream->dev->udev->speed == USB_SPEED_HIGH)
+		if (stream->dev->udev->speed >= USB_SPEED_HIGH)
 			bandwidth /= 8;
 		bandwidth += 12;
 
@@ -466,6 +471,7 @@
 	ktime_t time;
 	u16 host_sof;
 	u16 dev_sof;
+	u32 dev_stc;
 
 	switch (data[1] & (UVC_STREAM_PTS | UVC_STREAM_SCR)) {
 	case UVC_STREAM_PTS | UVC_STREAM_SCR:
@@ -510,6 +516,34 @@
 	if (dev_sof == stream->clock.last_sof)
 		return;
 
+	dev_stc = get_unaligned_le32(&data[header_size - 6]);
+
+	/*
+	 * STC (Source Time Clock) is the clock used by the camera. The UVC 1.5
+	 * standard states that it "must be captured when the first video data
+	 * of a video frame is put on the USB bus". This is generally understood
+	 * as requiring devices to clear the payload header's SCR bit before
+	 * the first packet containing video data.
+	 *
+	 * Most vendors follow that interpretation, but some (namely SunplusIT
+	 * on some devices) always set the `UVC_STREAM_SCR` bit, fill the SCR
+	 * field with 0's,and expect that the driver only processes the SCR if
+	 * there is data in the packet.
+	 *
+	 * Ignore all the hardware timestamp information if we haven't received
+	 * any data for this frame yet, the packet contains no data, and both
+	 * STC and SOF are zero. This heuristics should be safe on compliant
+	 * devices. This should be safe with compliant devices, as in the very
+	 * unlikely case where a UVC 1.1 device would send timing information
+	 * only before the first packet containing data, and both STC and SOF
+	 * happen to be zero for a particular frame, we would only miss one
+	 * clock sample from many and the clock recovery algorithm wouldn't
+	 * suffer from this condition.
+	 */
+	if (buf && buf->bytesused == 0 && len == header_size &&
+	    dev_stc == 0 && dev_sof == 0)
+		return;
+
 	stream->clock.last_sof = dev_sof;
 
 	host_sof = usb_get_current_frame_number(stream->dev->udev);
@@ -547,7 +581,7 @@
 	spin_lock_irqsave(&stream->clock.lock, flags);
 
 	sample = &stream->clock.samples[stream->clock.head];
-	sample->dev_stc = get_unaligned_le32(&data[header_size - 6]);
+	sample->dev_stc = dev_stc;
 	sample->dev_sof = dev_sof;
 	sample->host_sof = host_sof;
 	sample->host_time = time;
@@ -692,11 +726,11 @@
 	unsigned long flags;
 	u64 timestamp;
 	u32 delta_stc;
-	u32 y1, y2;
+	u32 y1;
 	u32 x1, x2;
 	u32 mean;
 	u32 sof;
-	u64 y;
+	u64 y, y2;
 
 	if (!uvc_hw_timestamps_param)
 		return;
@@ -736,7 +770,7 @@
 	sof = y;
 
 	uvc_dbg(stream->dev, CLOCK,
-		"%s: PTS %u y %llu.%06llu SOF %u.%06llu (x1 %u x2 %u y1 %u y2 %u SOF offset %u)\n",
+		"%s: PTS %u y %llu.%06llu SOF %u.%06llu (x1 %u x2 %u y1 %u y2 %llu SOF offset %u)\n",
 		stream->dev->name, buf->pts,
 		y >> 16, div_u64((y & 0xffff) * 1000000, 65536),
 		sof >> 16, div_u64(((u64)sof & 0xffff) * 1000000LLU, 65536),
@@ -751,7 +785,7 @@
 		goto done;
 
 	y1 = NSEC_PER_SEC;
-	y2 = (u32)ktime_to_ns(ktime_sub(last->host_time, first->host_time)) + y1;
+	y2 = ktime_to_ns(ktime_sub(last->host_time, first->host_time)) + y1;
 
 	/* Interpolated and host SOF timestamps can wrap around at slightly
 	 * different times. Handle this by adding or removing 2048 to or from
@@ -771,7 +805,7 @@
 	timestamp = ktime_to_ns(first->host_time) + y - y1;
 
 	uvc_dbg(stream->dev, CLOCK,
-		"%s: SOF %u.%06llu y %llu ts %llu buf ts %llu (x1 %u/%u/%u x2 %u/%u/%u y1 %u y2 %u)\n",
+		"%s: SOF %u.%06llu y %llu ts %llu buf ts %llu (x1 %u/%u/%u x2 %u/%u/%u y1 %u y2 %llu)\n",
 		stream->dev->name,
 		sof >> 16, div_u64(((u64)sof & 0xffff) * 1000000LLU, 65536),
 		y, timestamp, vbuf->vb2_buf.timestamp,
@@ -1329,7 +1363,9 @@
 	if (has_scr)
 		memcpy(stream->clock.last_scr, scr, 6);
 
-	memcpy(&meta->length, mem, length);
+	meta->length = mem[0];
+	meta->flags  = mem[1];
+	memcpy(meta->buf, &mem[2], length - 2);
 	meta_buf->bytesused += length + sizeof(meta->ns) + sizeof(meta->sof);
 
 	uvc_dbg(stream->dev, FRAME,
@@ -1946,6 +1982,17 @@
 			"Selecting alternate setting %u (%u B/frame bandwidth)\n",
 			altsetting, best_psize);
 
+		/*
+		 * Some devices, namely the Logitech C910 and B910, are unable
+		 * to recover from a USB autosuspend, unless the alternate
+		 * setting of the streaming interface is toggled.
+		 */
+		if (stream->dev->quirks & UVC_QUIRK_WAKE_AUTOSUSPEND) {
+			usb_set_interface(stream->dev->udev, intfnum,
+					  altsetting);
+			usb_set_interface(stream->dev->udev, intfnum, 0);
+		}
+
 		ret = usb_set_interface(stream->dev->udev, intfnum, altsetting);
 		if (ret < 0)
 			return ret;
@@ -1958,6 +2005,10 @@
 		if (ep == NULL)
 			return -EIO;
 
+		/* Reject broken descriptors. */
+		if (usb_endpoint_maxp(&ep->desc) == 0)
+			return -EIO;
+
 		ret = uvc_init_video_bulk(stream, ep, gfp_flags);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/usb/uvc/uvcvideo.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/usb/uvc/uvcvideo.h
@@ -183,13 +183,13 @@
 #define DRIVER_VERSION		"1.1.1"
 
 /* Number of isochronous URBs. */
-#define UVC_URBS		5
+#define UVC_URBS		50
 /* Maximum number of packets per URB. */
-#define UVC_MAX_PACKETS		32
+#define UVC_MAX_PACKETS		48
 /* Maximum status buffer size in bytes of interrupt URB. */
 #define UVC_MAX_STATUS_SIZE	16
 
-#define UVC_CTRL_CONTROL_TIMEOUT	500
+#define UVC_CTRL_CONTROL_TIMEOUT	5000
 #define UVC_CTRL_STREAMING_TIMEOUT	5000
 
 /* Maximum allowed number of control mappings per device */
@@ -209,6 +209,7 @@
 #define UVC_QUIRK_RESTORE_CTRLS_ON_INIT	0x00000400
 #define UVC_QUIRK_FORCE_Y8		0x00000800
 #define UVC_QUIRK_FORCE_BPP		0x00001000
+#define UVC_QUIRK_WAKE_AUTOSUSPEND	0x00002000
 
 /* Format flags */
 #define UVC_FMT_FLAG_COMPRESSED		0x00000001
@@ -241,7 +242,7 @@
 	struct list_head ev_subs;
 
 	u32 id;
-	u8 name[32];
+	char *name;
 	u8 entity[16];
 	u8 selector;
 
@@ -367,6 +368,7 @@
 			u8  *bmControls;
 			struct gpio_desc *gpio_privacy;
 			int irq;
+			bool initialized;
 		} gpio;
 	};
 
@@ -405,8 +407,6 @@
 	u32 fcc;
 	u32 flags;
 
-	char name[32];
-
 	unsigned int nframes;
 	struct uvc_frame *frame;
 };
@@ -452,6 +452,7 @@
 
 #define UVC_QUEUE_DISCONNECTED		(1 << 0)
 #define UVC_QUEUE_DROP_CORRUPTED	(1 << 1)
+#define UVC_QUEUE_STOPPING		(1 << 2)
 
 struct uvc_video_queue {
 	struct vb2_queue queue;
@@ -472,10 +473,15 @@
 	struct uvc_entity *processing;		/* Processing unit */
 	struct uvc_entity *selector;		/* Selector unit */
 
-	struct mutex ctrl_mutex;		/* Protects ctrl.info */
+	struct mutex ctrl_mutex;		/*
+						 * Protects ctrl.info,
+						 * ctrl.handle and
+						 * uvc_fh.pending_async_ctrls
+						 */
 
 	struct v4l2_prio_state prio;		/* V4L2 priority state */
 	u32 caps;				/* V4L2 chain-wide caps */
+	u8 ctrl_class_bitmap;			/* Bitmap of valid classes */
 };
 
 struct uvc_stats_frame {
@@ -697,6 +703,7 @@
 	/* Status Interrupt Endpoint */
 	struct usb_host_endpoint *int_ep;
 	struct urb *int_urb;
+	bool flush_status;
 	u8 *status;
 	struct input_dev *input;
 	char input_phys[64];
@@ -722,6 +729,7 @@
 	struct uvc_video_chain *chain;
 	struct uvc_streaming *stream;
 	enum uvc_handle_state state;
+	unsigned int pending_async_ctrls;
 };
 
 struct uvc_driver {
@@ -885,25 +893,28 @@
 
 int uvc_ctrl_begin(struct uvc_video_chain *chain);
 int __uvc_ctrl_commit(struct uvc_fh *handle, int rollback,
-		      const struct v4l2_ext_control *xctrls,
-		      unsigned int xctrls_count);
+		      struct v4l2_ext_controls *ctrls);
 static inline int uvc_ctrl_commit(struct uvc_fh *handle,
-				  const struct v4l2_ext_control *xctrls,
-				  unsigned int xctrls_count)
+				  struct v4l2_ext_controls *ctrls)
 {
-	return __uvc_ctrl_commit(handle, 0, xctrls, xctrls_count);
+	return __uvc_ctrl_commit(handle, 0, ctrls);
 }
 static inline int uvc_ctrl_rollback(struct uvc_fh *handle)
 {
-	return __uvc_ctrl_commit(handle, 1, NULL, 0);
+	return __uvc_ctrl_commit(handle, 1, NULL);
 }
 
 int uvc_ctrl_get(struct uvc_video_chain *chain, struct v4l2_ext_control *xctrl);
 int uvc_ctrl_set(struct uvc_fh *handle, struct v4l2_ext_control *xctrl);
+int uvc_ctrl_is_accessible(struct uvc_video_chain *chain, u32 v4l2_id,
+			   const struct v4l2_ext_controls *ctrls,
+			   unsigned long ioctl);
 
 int uvc_xu_ctrl_query(struct uvc_video_chain *chain,
 		      struct uvc_xu_control_query *xqry);
 
+void uvc_ctrl_cleanup_fh(struct uvc_fh *handle);
+
 /* Utility functions */
 void uvc_simplify_fraction(u32 *numerator, u32 *denominator,
 			   unsigned int n_terms, unsigned int threshold);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-common.c
@@ -273,6 +273,7 @@
 		{ .format = V4L2_PIX_FMT_YUV420,  .pixel_enc = V4L2_PIXEL_ENC_YUV, .mem_planes = 1, .comp_planes = 3, .bpp = { 1, 1, 1, 0 }, .hdiv = 2, .vdiv = 2 },
 		{ .format = V4L2_PIX_FMT_YVU420,  .pixel_enc = V4L2_PIXEL_ENC_YUV, .mem_planes = 1, .comp_planes = 3, .bpp = { 1, 1, 1, 0 }, .hdiv = 2, .vdiv = 2 },
 		{ .format = V4L2_PIX_FMT_YUV422P, .pixel_enc = V4L2_PIXEL_ENC_YUV, .mem_planes = 1, .comp_planes = 3, .bpp = { 1, 1, 1, 0 }, .hdiv = 2, .vdiv = 1 },
+		{ .format = V4L2_PIX_FMT_YUV444P, .pixel_enc = V4L2_PIXEL_ENC_YUV, .mem_planes = 1, .comp_planes = 3, .bpp = { 1, 1, 1, 0 }, .hdiv = 1, .vdiv = 1 },
 		{ .format = V4L2_PIX_FMT_GREY,    .pixel_enc = V4L2_PIXEL_ENC_YUV, .mem_planes = 1, .comp_planes = 1, .bpp = { 1, 0, 0, 0 }, .hdiv = 1, .vdiv = 1 },
 
 		/* YUV planar formats, non contiguous variant */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-compat-ioctl32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-compat-ioctl32.c
@@ -744,10 +744,6 @@
 /*
  * x86 is the only compat architecture with different struct alignment
  * between 32-bit and 64-bit tasks.
- *
- * On all other architectures, v4l2_event32 and v4l2_event32_time32 are
- * the same as v4l2_event and v4l2_event_time32, so we can use the native
- * handlers, converting v4l2_event to v4l2_event_time32 if necessary.
  */
 struct v4l2_event32 {
 	__u32				type;
@@ -765,21 +761,6 @@
 	__u32				reserved[8];
 };
 
-#ifdef CONFIG_COMPAT_32BIT_TIME
-struct v4l2_event32_time32 {
-	__u32				type;
-	union {
-		compat_s64		value64;
-		__u8			data[64];
-	} u;
-	__u32				pending;
-	__u32				sequence;
-	struct old_timespec32		timestamp;
-	__u32				id;
-	__u32				reserved[8];
-};
-#endif
-
 static int put_v4l2_event32(struct v4l2_event *p64,
 			    struct v4l2_event32 __user *p32)
 {
@@ -795,7 +776,22 @@
 	return 0;
 }
 
+#endif
+
 #ifdef CONFIG_COMPAT_32BIT_TIME
+struct v4l2_event32_time32 {
+	__u32				type;
+	union {
+		compat_s64		value64;
+		__u8			data[64];
+	} u;
+	__u32				pending;
+	__u32				sequence;
+	struct old_timespec32		timestamp;
+	__u32				id;
+	__u32				reserved[8];
+};
+
 static int put_v4l2_event32_time32(struct v4l2_event *p64,
 				   struct v4l2_event32_time32 __user *p32)
 {
@@ -811,7 +807,6 @@
 	return 0;
 }
 #endif
-#endif
 
 struct v4l2_edid32 {
 	__u32 pad;
@@ -873,9 +868,7 @@
 #define VIDIOC_QUERYBUF32_TIME32	_IOWR('V',  9, struct v4l2_buffer32_time32)
 #define VIDIOC_QBUF32_TIME32		_IOWR('V', 15, struct v4l2_buffer32_time32)
 #define VIDIOC_DQBUF32_TIME32		_IOWR('V', 17, struct v4l2_buffer32_time32)
-#ifdef CONFIG_X86_64
 #define	VIDIOC_DQEVENT32_TIME32		_IOR ('V', 89, struct v4l2_event32_time32)
-#endif
 #define VIDIOC_PREPARE_BUF32_TIME32	_IOWR('V', 93, struct v4l2_buffer32_time32)
 #endif
 
@@ -929,11 +922,11 @@
 #ifdef CONFIG_X86_64
 	case VIDIOC_DQEVENT32:
 		return VIDIOC_DQEVENT;
+#endif
 #ifdef CONFIG_COMPAT_32BIT_TIME
 	case VIDIOC_DQEVENT32_TIME32:
 		return VIDIOC_DQEVENT;
 #endif
-#endif
 	}
 	return cmd;
 }
@@ -1025,11 +1018,11 @@
 #ifdef CONFIG_X86_64
 	case VIDIOC_DQEVENT32:
 		return put_v4l2_event32(parg, arg);
+#endif
 #ifdef CONFIG_COMPAT_32BIT_TIME
 	case VIDIOC_DQEVENT32_TIME32:
 		return put_v4l2_event32_time32(parg, arg);
 #endif
-#endif
 	}
 	return 0;
 }
@@ -1040,6 +1033,8 @@
 {
 	int err = 0;
 
+	memset(mbuf, 0, array_size);
+
 	switch (cmd) {
 	case VIDIOC_G_FMT32:
 	case VIDIOC_S_FMT32:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-ctrls-api.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-ctrls-api.c
@@ -712,9 +712,10 @@
 		for (i = 0; i < master->ncontrols; i++)
 			cur_to_new(master->cluster[i]);
 		ret = call_op(master, g_volatile_ctrl);
-		new_to_user(c, ctrl);
+		if (!ret)
+			ret = new_to_user(c, ctrl);
 	} else {
-		cur_to_user(c, ctrl);
+		ret = cur_to_user(c, ctrl);
 	}
 	v4l2_ctrl_unlock(master);
 	return ret;
@@ -729,7 +730,10 @@
 	if (!ctrl || !ctrl->is_int)
 		return -EINVAL;
 	ret = get_ctrl(ctrl, &c);
-	control->value = c.value;
+
+	if (!ret)
+		control->value = c.value;
+
 	return ret;
 }
 EXPORT_SYMBOL(v4l2_g_ctrl);
@@ -770,10 +774,11 @@
 	int ret;
 
 	v4l2_ctrl_lock(ctrl);
-	user_to_new(c, ctrl);
-	ret = set_ctrl(fh, ctrl, 0);
+	ret = user_to_new(c, ctrl);
+	if (!ret)
+		ret = set_ctrl(fh, ctrl, 0);
 	if (!ret)
-		cur_to_user(c, ctrl);
+		ret = cur_to_user(c, ctrl);
 	v4l2_ctrl_unlock(ctrl);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-ctrls-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-ctrls-core.c
@@ -113,6 +113,7 @@
 	struct v4l2_ctrl_mpeg2_quantisation *p_mpeg2_quant;
 	struct v4l2_ctrl_vp8_frame *p_vp8_frame;
 	struct v4l2_ctrl_fwht_params *p_fwht_params;
+	struct v4l2_ctrl_h264_scaling_matrix *p_h264_scaling_matrix;
 	void *p = ptr.p + idx * ctrl->elem_size;
 
 	if (ctrl->p_def.p_const)
@@ -160,6 +161,15 @@
 		p_fwht_params->flags = V4L2_FWHT_FL_PIXENC_YUV |
 			(2 << V4L2_FWHT_FL_COMPONENTS_NUM_OFFSET);
 		break;
+	case V4L2_CTRL_TYPE_H264_SCALING_MATRIX:
+		p_h264_scaling_matrix = p;
+		/*
+		 * The default (flat) H.264 scaling matrix when none are
+		 * specified in the bitstream, this is according to formulas
+		 *  (7-8) and (7-9) of the specification.
+		 */
+		memset(p_h264_scaling_matrix, 16, sizeof(*p_h264_scaling_matrix));
+		break;
 	}
 }
 
@@ -1446,7 +1456,7 @@
 	else if (type == V4L2_CTRL_TYPE_INTEGER_MENU)
 		qmenu_int = v4l2_ctrl_get_int_menu(id, &qmenu_int_len);
 
-	if ((!qmenu && !qmenu_int) || (qmenu_int && max > qmenu_int_len)) {
+	if ((!qmenu && !qmenu_int) || (qmenu_int && max >= qmenu_int_len)) {
 		handler_set_err(hdl, -EINVAL);
 		return NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-dev.c
@@ -1033,8 +1033,10 @@
 	vdev->dev.devt = MKDEV(VIDEO_MAJOR, vdev->minor);
 	vdev->dev.parent = vdev->dev_parent;
 	dev_set_name(&vdev->dev, "%s%d", name_base, vdev->num);
+	mutex_lock(&videodev_lock);
 	ret = device_register(&vdev->dev);
 	if (ret < 0) {
+		mutex_unlock(&videodev_lock);
 		pr_err("%s: device_register failed\n", __func__);
 		goto cleanup;
 	}
@@ -1054,6 +1056,7 @@
 
 	/* Part 6: Activate this minor. The char device can now be used. */
 	set_bit(V4L2_FL_REGISTERED, &vdev->flags);
+	mutex_unlock(&videodev_lock);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-dv-timings.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-dv-timings.c
@@ -145,6 +145,8 @@
 	const struct v4l2_bt_timings *bt = &t->bt;
 	const struct v4l2_bt_timings_cap *cap = &dvcap->bt;
 	u32 caps = cap->capabilities;
+	const u32 max_vert = 10240;
+	u32 max_hor = 3 * bt->width;
 
 	if (t->type != V4L2_DV_BT_656_1120)
 		return false;
@@ -161,6 +163,26 @@
 	    (bt->interlaced && !(caps & V4L2_DV_BT_CAP_INTERLACED)) ||
 	    (!bt->interlaced && !(caps & V4L2_DV_BT_CAP_PROGRESSIVE)))
 		return false;
+
+	/* sanity checks for the blanking timings */
+	if (!bt->interlaced &&
+	    (bt->il_vbackporch || bt->il_vsync || bt->il_vfrontporch))
+		return false;
+	/*
+	 * Some video receivers cannot properly separate the frontporch,
+	 * backporch and sync values, and instead they only have the total
+	 * blanking. That can be assigned to any of these three fields.
+	 * So just check that none of these are way out of range.
+	 */
+	if (bt->hfrontporch > max_hor ||
+	    bt->hsync > max_hor || bt->hbackporch > max_hor)
+		return false;
+	if (bt->vfrontporch > max_vert ||
+	    bt->vsync > max_vert || bt->vbackporch > max_vert)
+		return false;
+	if (bt->interlaced && (bt->il_vfrontporch > max_vert ||
+	    bt->il_vsync > max_vert || bt->il_vbackporch > max_vert))
+		return false;
 	return fnc == NULL || fnc(t, fnc_handle);
 }
 EXPORT_SYMBOL_GPL(v4l2_valid_dv_timings);
@@ -459,25 +481,28 @@
  * @polarities - the horizontal and vertical polarities (same as struct
  *		v4l2_bt_timings polarities).
  * @interlaced - if this flag is true, it indicates interlaced format
- * @fmt - the resulting timings.
+ * @cap - the v4l2_dv_timings_cap capabilities.
+ * @timings - the resulting timings.
  *
  * This function will attempt to detect if the given values correspond to a
  * valid CVT format. If so, then it will return true, and fmt will be filled
  * in with the found CVT timings.
  */
-bool v4l2_detect_cvt(unsigned frame_height,
-		     unsigned hfreq,
-		     unsigned vsync,
-		     unsigned active_width,
+bool v4l2_detect_cvt(unsigned int frame_height,
+		     unsigned int hfreq,
+		     unsigned int vsync,
+		     unsigned int active_width,
 		     u32 polarities,
 		     bool interlaced,
-		     struct v4l2_dv_timings *fmt)
+		     const struct v4l2_dv_timings_cap *cap,
+		     struct v4l2_dv_timings *timings)
 {
-	int  v_fp, v_bp, h_fp, h_bp, hsync;
-	int  frame_width, image_height, image_width;
+	struct v4l2_dv_timings t = {};
+	int v_fp, v_bp, h_fp, h_bp, hsync;
+	int frame_width, image_height, image_width;
 	bool reduced_blanking;
 	bool rb_v2 = false;
-	unsigned pix_clk;
+	unsigned int pix_clk;
 
 	if (vsync < 4 || vsync > 8)
 		return false;
@@ -603,36 +628,39 @@
 		h_fp = h_blank - hsync - h_bp;
 	}
 
-	fmt->type = V4L2_DV_BT_656_1120;
-	fmt->bt.polarities = polarities;
-	fmt->bt.width = image_width;
-	fmt->bt.height = image_height;
-	fmt->bt.hfrontporch = h_fp;
-	fmt->bt.vfrontporch = v_fp;
-	fmt->bt.hsync = hsync;
-	fmt->bt.vsync = vsync;
-	fmt->bt.hbackporch = frame_width - image_width - h_fp - hsync;
+	t.type = V4L2_DV_BT_656_1120;
+	t.bt.polarities = polarities;
+	t.bt.width = image_width;
+	t.bt.height = image_height;
+	t.bt.hfrontporch = h_fp;
+	t.bt.vfrontporch = v_fp;
+	t.bt.hsync = hsync;
+	t.bt.vsync = vsync;
+	t.bt.hbackporch = frame_width - image_width - h_fp - hsync;
 
 	if (!interlaced) {
-		fmt->bt.vbackporch = frame_height - image_height - v_fp - vsync;
-		fmt->bt.interlaced = V4L2_DV_PROGRESSIVE;
+		t.bt.vbackporch = frame_height - image_height - v_fp - vsync;
+		t.bt.interlaced = V4L2_DV_PROGRESSIVE;
 	} else {
-		fmt->bt.vbackporch = (frame_height - image_height - 2 * v_fp -
+		t.bt.vbackporch = (frame_height - image_height - 2 * v_fp -
 				      2 * vsync) / 2;
-		fmt->bt.il_vbackporch = frame_height - image_height - 2 * v_fp -
-					2 * vsync - fmt->bt.vbackporch;
-		fmt->bt.il_vfrontporch = v_fp;
-		fmt->bt.il_vsync = vsync;
-		fmt->bt.flags |= V4L2_DV_FL_HALF_LINE;
-		fmt->bt.interlaced = V4L2_DV_INTERLACED;
+		t.bt.il_vbackporch = frame_height - image_height - 2 * v_fp -
+					2 * vsync - t.bt.vbackporch;
+		t.bt.il_vfrontporch = v_fp;
+		t.bt.il_vsync = vsync;
+		t.bt.flags |= V4L2_DV_FL_HALF_LINE;
+		t.bt.interlaced = V4L2_DV_INTERLACED;
 	}
 
-	fmt->bt.pixelclock = pix_clk;
-	fmt->bt.standards = V4L2_DV_BT_STD_CVT;
+	t.bt.pixelclock = pix_clk;
+	t.bt.standards = V4L2_DV_BT_STD_CVT;
 
 	if (reduced_blanking)
-		fmt->bt.flags |= V4L2_DV_FL_REDUCED_BLANKING;
+		t.bt.flags |= V4L2_DV_FL_REDUCED_BLANKING;
 
+	if (!v4l2_valid_dv_timings(&t, cap, NULL, NULL))
+		return false;
+	*timings = t;
 	return true;
 }
 EXPORT_SYMBOL_GPL(v4l2_detect_cvt);
@@ -677,22 +705,25 @@
  *		image height, so it has to be passed explicitly. Usually
  *		the native screen aspect ratio is used for this. If it
  *		is not filled in correctly, then 16:9 will be assumed.
- * @fmt - the resulting timings.
+ * @cap - the v4l2_dv_timings_cap capabilities.
+ * @timings - the resulting timings.
  *
  * This function will attempt to detect if the given values correspond to a
  * valid GTF format. If so, then it will return true, and fmt will be filled
  * in with the found GTF timings.
  */
-bool v4l2_detect_gtf(unsigned frame_height,
-		unsigned hfreq,
-		unsigned vsync,
-		u32 polarities,
-		bool interlaced,
-		struct v4l2_fract aspect,
-		struct v4l2_dv_timings *fmt)
+bool v4l2_detect_gtf(unsigned int frame_height,
+		     unsigned int hfreq,
+		     unsigned int vsync,
+		     u32 polarities,
+		     bool interlaced,
+		     struct v4l2_fract aspect,
+		     const struct v4l2_dv_timings_cap *cap,
+		     struct v4l2_dv_timings *timings)
 {
+	struct v4l2_dv_timings t = {};
 	int pix_clk;
-	int  v_fp, v_bp, h_fp, hsync;
+	int v_fp, v_bp, h_fp, hsync;
 	int frame_width, image_height, image_width;
 	bool default_gtf;
 	int h_blank;
@@ -761,36 +792,39 @@
 
 	h_fp = h_blank / 2 - hsync;
 
-	fmt->type = V4L2_DV_BT_656_1120;
-	fmt->bt.polarities = polarities;
-	fmt->bt.width = image_width;
-	fmt->bt.height = image_height;
-	fmt->bt.hfrontporch = h_fp;
-	fmt->bt.vfrontporch = v_fp;
-	fmt->bt.hsync = hsync;
-	fmt->bt.vsync = vsync;
-	fmt->bt.hbackporch = frame_width - image_width - h_fp - hsync;
+	t.type = V4L2_DV_BT_656_1120;
+	t.bt.polarities = polarities;
+	t.bt.width = image_width;
+	t.bt.height = image_height;
+	t.bt.hfrontporch = h_fp;
+	t.bt.vfrontporch = v_fp;
+	t.bt.hsync = hsync;
+	t.bt.vsync = vsync;
+	t.bt.hbackporch = frame_width - image_width - h_fp - hsync;
 
 	if (!interlaced) {
-		fmt->bt.vbackporch = frame_height - image_height - v_fp - vsync;
-		fmt->bt.interlaced = V4L2_DV_PROGRESSIVE;
+		t.bt.vbackporch = frame_height - image_height - v_fp - vsync;
+		t.bt.interlaced = V4L2_DV_PROGRESSIVE;
 	} else {
-		fmt->bt.vbackporch = (frame_height - image_height - 2 * v_fp -
+		t.bt.vbackporch = (frame_height - image_height - 2 * v_fp -
 				      2 * vsync) / 2;
-		fmt->bt.il_vbackporch = frame_height - image_height - 2 * v_fp -
-					2 * vsync - fmt->bt.vbackporch;
-		fmt->bt.il_vfrontporch = v_fp;
-		fmt->bt.il_vsync = vsync;
-		fmt->bt.flags |= V4L2_DV_FL_HALF_LINE;
-		fmt->bt.interlaced = V4L2_DV_INTERLACED;
+		t.bt.il_vbackporch = frame_height - image_height - 2 * v_fp -
+					2 * vsync - t.bt.vbackporch;
+		t.bt.il_vfrontporch = v_fp;
+		t.bt.il_vsync = vsync;
+		t.bt.flags |= V4L2_DV_FL_HALF_LINE;
+		t.bt.interlaced = V4L2_DV_INTERLACED;
 	}
 
-	fmt->bt.pixelclock = pix_clk;
-	fmt->bt.standards = V4L2_DV_BT_STD_GTF;
+	t.bt.pixelclock = pix_clk;
+	t.bt.standards = V4L2_DV_BT_STD_GTF;
 
 	if (!default_gtf)
-		fmt->bt.flags |= V4L2_DV_FL_REDUCED_BLANKING;
+		t.bt.flags |= V4L2_DV_FL_REDUCED_BLANKING;
 
+	if (!v4l2_valid_dv_timings(&t, cap, NULL, NULL))
+		return false;
+	*timings = t;
 	return true;
 }
 EXPORT_SYMBOL_GPL(v4l2_detect_gtf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-fwnode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-fwnode.c
@@ -549,19 +549,29 @@
 	link->local_id = fwep.id;
 	link->local_port = fwep.port;
 	link->local_node = fwnode_graph_get_port_parent(fwnode);
+	if (!link->local_node)
+		return -ENOLINK;
 
 	fwnode = fwnode_graph_get_remote_endpoint(fwnode);
-	if (!fwnode) {
-		fwnode_handle_put(fwnode);
-		return -ENOLINK;
-	}
+	if (!fwnode)
+		goto err_put_local_node;
 
 	fwnode_graph_parse_endpoint(fwnode, &fwep);
 	link->remote_id = fwep.id;
 	link->remote_port = fwep.port;
 	link->remote_node = fwnode_graph_get_port_parent(fwnode);
+	if (!link->remote_node)
+		goto err_put_remote_endpoint;
 
 	return 0;
+
+err_put_remote_endpoint:
+	fwnode_handle_put(fwnode);
+
+err_put_local_node:
+	fwnode_handle_put(link->local_node);
+
+	return -ENOLINK;
 }
 EXPORT_SYMBOL_GPL(v4l2_fwnode_parse_link);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-ioctl.c
@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/version.h>
 
+#include <linux/v4l2-subdev.h>
 #include <linux/videodev2.h>
 
 #include <media/v4l2-common.h>
@@ -279,8 +280,8 @@
 	const struct v4l2_vbi_format *vbi;
 	const struct v4l2_sliced_vbi_format *sliced;
 	const struct v4l2_window *win;
-	const struct v4l2_sdr_format *sdr;
 	const struct v4l2_meta_format *meta;
+	u32 pixelformat;
 	u32 planes;
 	unsigned i;
 
@@ -299,8 +300,9 @@
 	case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE:
 	case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE:
 		mp = &p->fmt.pix_mp;
+		pixelformat = mp->pixelformat;
 		pr_cont(", width=%u, height=%u, format=%p4cc, field=%s, colorspace=%d, num_planes=%u, flags=0x%x, ycbcr_enc=%u, quantization=%u, xfer_func=%u\n",
-			mp->width, mp->height, &mp->pixelformat,
+			mp->width, mp->height, &pixelformat,
 			prt_names(mp->field, v4l2_field_names),
 			mp->colorspace, mp->num_planes, mp->flags,
 			mp->ycbcr_enc, mp->quantization, mp->xfer_func);
@@ -343,14 +345,15 @@
 		break;
 	case V4L2_BUF_TYPE_SDR_CAPTURE:
 	case V4L2_BUF_TYPE_SDR_OUTPUT:
-		sdr = &p->fmt.sdr;
-		pr_cont(", pixelformat=%p4cc\n", &sdr->pixelformat);
+		pixelformat = p->fmt.sdr.pixelformat;
+		pr_cont(", pixelformat=%p4cc\n", &pixelformat);
 		break;
 	case V4L2_BUF_TYPE_META_CAPTURE:
 	case V4L2_BUF_TYPE_META_OUTPUT:
 		meta = &p->fmt.meta;
+		pixelformat = meta->dataformat;
 		pr_cont(", dataformat=%p4cc, buffersize=%u\n",
-			&meta->dataformat, meta->buffersize);
+			&pixelformat, meta->buffersize);
 		break;
 	}
 }
@@ -869,7 +872,7 @@
 	pr_cont("driver-specific ioctl\n");
 }
 
-static int check_ext_ctrls(struct v4l2_ext_controls *c, int allow_priv)
+static bool check_ext_ctrls(struct v4l2_ext_controls *c, unsigned long ioctl)
 {
 	__u32 i;
 
@@ -878,23 +881,41 @@
 	for (i = 0; i < c->count; i++)
 		c->controls[i].reserved2[0] = 0;
 
-	/* V4L2_CID_PRIVATE_BASE cannot be used as control class
-	   when using extended controls.
-	   Only when passed in through VIDIOC_G_CTRL and VIDIOC_S_CTRL
-	   is it allowed for backwards compatibility.
-	 */
-	if (!allow_priv && c->which == V4L2_CID_PRIVATE_BASE)
-		return 0;
-	if (!c->which)
-		return 1;
+	switch (c->which) {
+	case V4L2_CID_PRIVATE_BASE:
+		/*
+		 * V4L2_CID_PRIVATE_BASE cannot be used as control class
+		 * when using extended controls.
+		 * Only when passed in through VIDIOC_G_CTRL and VIDIOC_S_CTRL
+		 * is it allowed for backwards compatibility.
+		 */
+		if (ioctl == VIDIOC_G_CTRL || ioctl == VIDIOC_S_CTRL)
+			return false;
+		break;
+	case V4L2_CTRL_WHICH_DEF_VAL:
+		/* Default value cannot be changed */
+		if (ioctl == VIDIOC_S_EXT_CTRLS ||
+		    ioctl == VIDIOC_TRY_EXT_CTRLS) {
+			c->error_idx = c->count;
+			return false;
+		}
+		return true;
+	case V4L2_CTRL_WHICH_CUR_VAL:
+		return true;
+	case V4L2_CTRL_WHICH_REQUEST_VAL:
+		c->error_idx = c->count;
+		return false;
+	}
+
 	/* Check that all controls are from the same control class. */
 	for (i = 0; i < c->count; i++) {
 		if (V4L2_CTRL_ID2WHICH(c->controls[i].id) != c->which) {
-			c->error_idx = i;
-			return 0;
+			c->error_idx = ioctl == VIDIOC_TRY_EXT_CTRLS ? i :
+								      c->count;
+			return false;
 		}
 	}
-	return 1;
+	return true;
 }
 
 static int check_fmt(struct file *file, enum v4l2_buf_type type)
@@ -1235,6 +1256,9 @@
 	case V4L2_PIX_FMT_BGRX32:	descr = "32-bit XBGR 8-8-8-8"; break;
 	case V4L2_PIX_FMT_RGBA32:	descr = "32-bit RGBA 8-8-8-8"; break;
 	case V4L2_PIX_FMT_RGBX32:	descr = "32-bit RGBX 8-8-8-8"; break;
+	case V4L2_PIX_FMT_XBGR30:	descr = "32-bit XBGR 2-10-10-10"; break;
+	case V4L2_PIX_FMT_XBGR40:	descr = "40-bit XBGR 4-12-12-12"; break;
+	case V4L2_PIX_FMT_BGR48:	descr = "48-bit BGR 16-16-16"; break;
 	case V4L2_PIX_FMT_GREY:		descr = "8-bit Greyscale"; break;
 	case V4L2_PIX_FMT_Y4:		descr = "4-bit Greyscale"; break;
 	case V4L2_PIX_FMT_Y6:		descr = "6-bit Greyscale"; break;
@@ -1260,9 +1284,14 @@
 	case V4L2_PIX_FMT_UYVY:		descr = "UYVY 4:2:2"; break;
 	case V4L2_PIX_FMT_VYUY:		descr = "VYUY 4:2:2"; break;
 	case V4L2_PIX_FMT_YUV422P:	descr = "Planar YUV 4:2:2"; break;
+	case V4L2_PIX_FMT_YUV444P:	descr = "3 Planar YUV 4:4:4 8-bit"; break;
 	case V4L2_PIX_FMT_YUV411P:	descr = "Planar YUV 4:1:1"; break;
+	case V4L2_PIX_FMT_X403:		descr = "3 Planar YUV 4:4:4 10-bit"; break;
 	case V4L2_PIX_FMT_Y41P:		descr = "YUV 4:1:1 (Packed)"; break;
 	case V4L2_PIX_FMT_YUV444:	descr = "16-bit A/XYUV 4-4-4-4"; break;
+	case V4L2_PIX_FMT_XVUY32:	descr = "32-bit packed XVUY 8-8-8-8"; break;
+	case V4L2_PIX_FMT_AVUY32:	descr = "32-bit packed AVUY 8-8-8-8"; break;
+	case V4L2_PIX_FMT_VUY24:	descr = "24-bit packed VUY 8-8-8"; break;
 	case V4L2_PIX_FMT_YUV555:	descr = "16-bit A/XYUV 1-5-5-5"; break;
 	case V4L2_PIX_FMT_YUV565:	descr = "16-bit YUV 5-6-5"; break;
 	case V4L2_PIX_FMT_YUV24:	descr = "24-bit YUV 4:4:4 8-8-8"; break;
@@ -1276,24 +1305,41 @@
 	case V4L2_PIX_FMT_HI240:	descr = "8-bit Dithered RGB (BTTV)"; break;
 	case V4L2_PIX_FMT_HM12:		descr = "YUV 4:2:0 (16x16 Macroblocks)"; break;
 	case V4L2_PIX_FMT_M420:		descr = "YUV 4:2:0 (M420)"; break;
+	case V4L2_PIX_FMT_XVUY10:	descr = "XVUY 2-10-10-10"; break;
 	case V4L2_PIX_FMT_NV12:		descr = "Y/CbCr 4:2:0"; break;
 	case V4L2_PIX_FMT_NV21:		descr = "Y/CrCb 4:2:0"; break;
 	case V4L2_PIX_FMT_NV16:		descr = "Y/CbCr 4:2:2"; break;
 	case V4L2_PIX_FMT_NV61:		descr = "Y/CrCb 4:2:2"; break;
 	case V4L2_PIX_FMT_NV24:		descr = "Y/CbCr 4:4:4"; break;
 	case V4L2_PIX_FMT_NV42:		descr = "Y/CrCb 4:4:4"; break;
+	case V4L2_PIX_FMT_XV15:         descr = "Y/CrCb 4:2:0 10-bit"; break;
+	case V4L2_PIX_FMT_XV20:		descr = "Y/CrCb 4:2:2 10-bit"; break;
 	case V4L2_PIX_FMT_NV12M:	descr = "Y/CbCr 4:2:0 (N-C)"; break;
 	case V4L2_PIX_FMT_NV21M:	descr = "Y/CrCb 4:2:0 (N-C)"; break;
 	case V4L2_PIX_FMT_NV16M:	descr = "Y/CbCr 4:2:2 (N-C)"; break;
 	case V4L2_PIX_FMT_NV61M:	descr = "Y/CrCb 4:2:2 (N-C)"; break;
 	case V4L2_PIX_FMT_NV12MT:	descr = "Y/CbCr 4:2:0 (64x32 MB, N-C)"; break;
 	case V4L2_PIX_FMT_NV12MT_16X16:	descr = "Y/CbCr 4:2:0 (16x16 MB, N-C)"; break;
+	case V4L2_PIX_FMT_XV20M:        descr = "Y/CrCb 4:2:2 10-bit (N-C)"; break;
+	case V4L2_PIX_FMT_XV15M:        descr = "Y/CrCb 4:2:0 10-bit (N-C)"; break;
 	case V4L2_PIX_FMT_YUV420M:	descr = "Planar YUV 4:2:0 (N-C)"; break;
 	case V4L2_PIX_FMT_YVU420M:	descr = "Planar YVU 4:2:0 (N-C)"; break;
 	case V4L2_PIX_FMT_YUV422M:	descr = "Planar YUV 4:2:2 (N-C)"; break;
 	case V4L2_PIX_FMT_YVU422M:	descr = "Planar YVU 4:2:2 (N-C)"; break;
 	case V4L2_PIX_FMT_YUV444M:	descr = "Planar YUV 4:4:4 (N-C)"; break;
 	case V4L2_PIX_FMT_YVU444M:	descr = "Planar YVU 4:4:4 (N-C)"; break;
+	case V4L2_PIX_FMT_X012:		descr = "Y/CbCr 4:2:0, 4-12-12-12"; break;
+	case V4L2_PIX_FMT_X012M:	descr = "Y/CbCr 4:2:0, 4-12-12-12 (N-C)"; break;
+	case V4L2_PIX_FMT_X212:		descr = "Y/CbCr 4:2:2, 4-12-12-12"; break;
+	case V4L2_PIX_FMT_X212M:	descr = "Y/CbCr 4:2:2, 4-12-12-12 (N-C)"; break;
+	case V4L2_PIX_FMT_X412:		descr = "Y/CbCr 4:4:4, 4-12-12-12"; break;
+	case V4L2_PIX_FMT_X412M:	descr = "Y/CbCr 4:4:4, 4-12-12-12 (N-C)"; break;
+	case V4L2_PIX_FMT_X016:		descr = "Y/CbCr 4:2:0, 16-16-16"; break;
+	case V4L2_PIX_FMT_X016M:	descr = "Y/CbCr 4:2:0, 16-16-16 (N-C)"; break;
+	case V4L2_PIX_FMT_X216:		descr = "Y/CbCr 4:2:2, 16-16-16"; break;
+	case V4L2_PIX_FMT_X216M:	descr = "Y/CbCr 4:2:2, 16-16-16 (N-C)"; break;
+	case V4L2_PIX_FMT_X416:		descr = "Y/CbCr 4:4:4, 16-16-16"; break;
+	case V4L2_PIX_FMT_X416M:	descr = "Y/CbCr 4:4:4, 16-16-16 (N-C)"; break;
 	case V4L2_PIX_FMT_SBGGR8:	descr = "8-bit Bayer BGBG/GRGR"; break;
 	case V4L2_PIX_FMT_SGBRG8:	descr = "8-bit Bayer GBGB/RGRG"; break;
 	case V4L2_PIX_FMT_SGRBG8:	descr = "8-bit Bayer GRGR/BGBG"; break;
@@ -2070,6 +2116,7 @@
 static int v4l_g_parm(const struct v4l2_ioctl_ops *ops,
 				struct file *file, void *fh, void *arg)
 {
+	struct video_device *vfd = video_devdata(file);
 	struct v4l2_streamparm *p = arg;
 	v4l2_std_id std;
 	int ret = check_fmt(file, p->type);
@@ -2081,7 +2128,8 @@
 	if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE &&
 	    p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE)
 		return -EINVAL;
-	p->parm.capture.readbuffers = 2;
+	if (vfd->device_caps & V4L2_CAP_READWRITE)
+		p->parm.capture.readbuffers = 2;
 	ret = ops->vidioc_g_std(file, fh, &std);
 	if (ret == 0)
 		v4l2_video_std_frame_period(std, &p->parm.capture.timeperframe);
@@ -2187,7 +2235,7 @@
 	ctrls.controls = &ctrl;
 	ctrl.id = p->id;
 	ctrl.value = p->value;
-	if (check_ext_ctrls(&ctrls, 1)) {
+	if (check_ext_ctrls(&ctrls, VIDIOC_G_CTRL)) {
 		int ret = ops->vidioc_g_ext_ctrls(file, fh, &ctrls);
 
 		if (ret == 0)
@@ -2206,6 +2254,7 @@
 		test_bit(V4L2_FL_USES_V4L2_FH, &vfd->flags) ? fh : NULL;
 	struct v4l2_ext_controls ctrls;
 	struct v4l2_ext_control ctrl;
+	int ret;
 
 	if (vfh && vfh->ctrl_handler)
 		return v4l2_s_ctrl(vfh, vfh->ctrl_handler, p);
@@ -2221,9 +2270,11 @@
 	ctrls.controls = &ctrl;
 	ctrl.id = p->id;
 	ctrl.value = p->value;
-	if (check_ext_ctrls(&ctrls, 1))
-		return ops->vidioc_s_ext_ctrls(file, fh, &ctrls);
-	return -EINVAL;
+	if (!check_ext_ctrls(&ctrls, VIDIOC_S_CTRL))
+		return -EINVAL;
+	ret = ops->vidioc_s_ext_ctrls(file, fh, &ctrls);
+	p->value = ctrl.value;
+	return ret;
 }
 
 static int v4l_g_ext_ctrls(const struct v4l2_ioctl_ops *ops,
@@ -2243,8 +2294,8 @@
 					vfd, vfd->v4l2_dev->mdev, p);
 	if (ops->vidioc_g_ext_ctrls == NULL)
 		return -ENOTTY;
-	return check_ext_ctrls(p, 0) ? ops->vidioc_g_ext_ctrls(file, fh, p) :
-					-EINVAL;
+	return check_ext_ctrls(p, VIDIOC_G_EXT_CTRLS) ?
+				ops->vidioc_g_ext_ctrls(file, fh, p) : -EINVAL;
 }
 
 static int v4l_s_ext_ctrls(const struct v4l2_ioctl_ops *ops,
@@ -2264,8 +2315,8 @@
 					vfd, vfd->v4l2_dev->mdev, p);
 	if (ops->vidioc_s_ext_ctrls == NULL)
 		return -ENOTTY;
-	return check_ext_ctrls(p, 0) ? ops->vidioc_s_ext_ctrls(file, fh, p) :
-					-EINVAL;
+	return check_ext_ctrls(p, VIDIOC_S_EXT_CTRLS) ?
+				ops->vidioc_s_ext_ctrls(file, fh, p) : -EINVAL;
 }
 
 static int v4l_try_ext_ctrls(const struct v4l2_ioctl_ops *ops,
@@ -2285,8 +2336,8 @@
 					  vfd, vfd->v4l2_dev->mdev, p);
 	if (ops->vidioc_try_ext_ctrls == NULL)
 		return -ENOTTY;
-	return check_ext_ctrls(p, 0) ? ops->vidioc_try_ext_ctrls(file, fh, p) :
-					-EINVAL;
+	return check_ext_ctrls(p, VIDIOC_TRY_EXT_CTRLS) ?
+			ops->vidioc_try_ext_ctrls(file, fh, p) : -EINVAL;
 }
 
 /*
@@ -3043,6 +3094,23 @@
 			ret = 1;
 		}
 		break;
+	}
+
+	case VIDIOC_SUBDEV_G_ROUTING:
+	case VIDIOC_SUBDEV_S_ROUTING: {
+		struct v4l2_subdev_routing *route = parg;
+
+		if (route->num_routes > 0) {
+			if (route->num_routes > 256)
+				return -EINVAL;
+
+			*user_ptr = (void __user *)route->routes;
+			*kernel_ptr = (void *)&route->routes;
+			*array_size = sizeof(struct v4l2_plane)
+				    * route->num_routes;
+			ret = 1;
+		}
+		break;
 	}
 	case VIDIOC_G_FMT:
 	case VIDIOC_S_FMT:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-jpeg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-jpeg.c
@@ -460,7 +460,7 @@
 	/* Check for "Adobe\0" in Ap1..6 */
 	if (stream->curr + 6 > stream->end ||
 	    strncmp(stream->curr, "Adobe\0", 6))
-		return -EINVAL;
+		return jpeg_skip(stream, lp - 2);
 
 	/* get to Ap12 */
 	ret = jpeg_skip(stream, 11);
@@ -474,7 +474,7 @@
 	*tf = ret;
 
 	/* skip the rest of the segment, this ensures at least it is complete */
-	skip = lp - 2 - 11;
+	skip = lp - 2 - 11 - 1;
 	return jpeg_skip(stream, skip);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-mc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-mc.c
@@ -321,7 +321,7 @@
 
 	sink_sd = media_entity_to_v4l2_subdev(sink->entity);
 
-	fwnode_graph_for_each_endpoint(dev_fwnode(src_sd->dev), endpoint) {
+	fwnode_graph_for_each_endpoint(src_sd->fwnode, endpoint) {
 		struct fwnode_handle *remote_ep;
 		int src_idx, sink_idx, ret;
 		struct media_pad *src;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-mem2mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-mem2mem.c
@@ -585,19 +585,14 @@
 }
 EXPORT_SYMBOL_GPL(v4l2_m2m_reqbufs);
 
-int v4l2_m2m_querybuf(struct file *file, struct v4l2_m2m_ctx *m2m_ctx,
-		      struct v4l2_buffer *buf)
+static void v4l2_m2m_adjust_mem_offset(struct vb2_queue *vq,
+				       struct v4l2_buffer *buf)
 {
-	struct vb2_queue *vq;
-	int ret = 0;
-	unsigned int i;
-
-	vq = v4l2_m2m_get_vq(m2m_ctx, buf->type);
-	ret = vb2_querybuf(vq, buf);
-
 	/* Adjust MMAP memory offsets for the CAPTURE queue */
 	if (buf->memory == V4L2_MEMORY_MMAP && V4L2_TYPE_IS_CAPTURE(vq->type)) {
 		if (V4L2_TYPE_IS_MULTIPLANAR(vq->type)) {
+			unsigned int i;
+
 			for (i = 0; i < buf->length; ++i)
 				buf->m.planes[i].m.mem_offset
 					+= DST_QUEUE_OFF_BASE;
@@ -605,8 +600,23 @@
 			buf->m.offset += DST_QUEUE_OFF_BASE;
 		}
 	}
+}
 
-	return ret;
+int v4l2_m2m_querybuf(struct file *file, struct v4l2_m2m_ctx *m2m_ctx,
+		      struct v4l2_buffer *buf)
+{
+	struct vb2_queue *vq;
+	int ret;
+
+	vq = v4l2_m2m_get_vq(m2m_ctx, buf->type);
+	ret = vb2_querybuf(vq, buf);
+	if (ret)
+		return ret;
+
+	/* Adjust MMAP memory offsets for the CAPTURE queue */
+	v4l2_m2m_adjust_mem_offset(vq, buf);
+
+	return 0;
 }
 EXPORT_SYMBOL_GPL(v4l2_m2m_querybuf);
 
@@ -763,6 +773,9 @@
 	if (ret)
 		return ret;
 
+	/* Adjust MMAP memory offsets for the CAPTURE queue */
+	v4l2_m2m_adjust_mem_offset(vq, buf);
+
 	/*
 	 * If the capture queue is streaming, but streaming hasn't started
 	 * on the device, but was asked to stop, mark the previously queued
@@ -784,9 +797,17 @@
 		   struct v4l2_buffer *buf)
 {
 	struct vb2_queue *vq;
+	int ret;
 
 	vq = v4l2_m2m_get_vq(m2m_ctx, buf->type);
-	return vb2_dqbuf(vq, buf, file->f_flags & O_NONBLOCK);
+	ret = vb2_dqbuf(vq, buf, file->f_flags & O_NONBLOCK);
+	if (ret)
+		return ret;
+
+	/* Adjust MMAP memory offsets for the CAPTURE queue */
+	v4l2_m2m_adjust_mem_offset(vq, buf);
+
+	return 0;
 }
 EXPORT_SYMBOL_GPL(v4l2_m2m_dqbuf);
 
@@ -795,9 +816,17 @@
 {
 	struct video_device *vdev = video_devdata(file);
 	struct vb2_queue *vq;
+	int ret;
 
 	vq = v4l2_m2m_get_vq(m2m_ctx, buf->type);
-	return vb2_prepare_buf(vq, vdev->v4l2_dev->mdev, buf);
+	ret = vb2_prepare_buf(vq, vdev->v4l2_dev->mdev, buf);
+	if (ret)
+		return ret;
+
+	/* Adjust MMAP memory offsets for the CAPTURE queue */
+	v4l2_m2m_adjust_mem_offset(vq, buf);
+
+	return 0;
 }
 EXPORT_SYMBOL_GPL(v4l2_m2m_prepare_buf);
 
@@ -895,7 +924,7 @@
 	if ((!src_q->streaming || src_q->error ||
 	     list_empty(&src_q->queued_list)) &&
 	    (!dst_q->streaming || dst_q->error ||
-	     list_empty(&dst_q->queued_list)))
+	     (list_empty(&dst_q->queued_list) && !dst_q->last_buffer_dequeued)))
 		return EPOLLERR;
 
 	spin_lock_irqsave(&src_q->done_lock, flags);
@@ -1033,11 +1062,17 @@
 	entity->function = function;
 
 	ret = media_entity_pads_init(entity, num_pads, pads);
-	if (ret)
+	if (ret) {
+		kfree(entity->name);
+		entity->name = NULL;
 		return ret;
+	}
 	ret = media_device_register_entity(mdev, entity);
-	if (ret)
+	if (ret) {
+		kfree(entity->name);
+		entity->name = NULL;
 		return ret;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/v4l2-subdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/v4l2-subdev.c
@@ -634,6 +634,33 @@
 
 		return v4l2_subdev_call(sd, video, s_dv_timings, arg);
 
+	case VIDIOC_SUBDEV_G_ROUTING:
+		return v4l2_subdev_call(sd, pad, get_routing, arg);
+
+	case VIDIOC_SUBDEV_S_ROUTING: {
+		struct v4l2_subdev_routing *route = arg;
+		unsigned int i;
+
+		if (route->num_routes > sd->entity.num_pads)
+			return -EINVAL;
+
+		for (i = 0; i < route->num_routes; ++i) {
+			unsigned int sink = route->routes[i].sink;
+			unsigned int source = route->routes[i].source;
+			struct media_pad *pads = sd->entity.pads;
+
+			if (sink >= sd->entity.num_pads ||
+			    source >= sd->entity.num_pads)
+				return -EINVAL;
+
+			if (!(pads[sink].flags & MEDIA_PAD_FL_SINK) ||
+			    !(pads[source].flags & MEDIA_PAD_FL_SOURCE))
+				return -EINVAL;
+		}
+
+		return v4l2_subdev_call(sd, pad, set_routing, route);
+	}
+
 	case VIDIOC_SUBDEV_G_STD:
 		return v4l2_subdev_call(sd, video, g_std, arg);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/media/v4l2-core/videobuf-dma-contig.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/media/v4l2-core/videobuf-dma-contig.c
@@ -36,12 +36,11 @@
 
 static int __videobuf_dc_alloc(struct device *dev,
 			       struct videobuf_dma_contig_memory *mem,
-			       unsigned long size, gfp_t flags)
+			       unsigned long size)
 {
 	mem->size = size;
-	mem->vaddr = dma_alloc_coherent(dev, mem->size,
-					&mem->dma_handle, flags);
-
+	mem->vaddr = dma_alloc_coherent(dev, mem->size, &mem->dma_handle,
+					GFP_KERNEL);
 	if (!mem->vaddr) {
 		dev_err(dev, "memory alloc size %ld failed\n", mem->size);
 		return -ENOMEM;
@@ -258,8 +257,7 @@
 			return videobuf_dma_contig_user_get(mem, vb);
 
 		/* allocate memory for the read() method */
-		if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(vb->size),
-					GFP_KERNEL))
+		if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(vb->size)))
 			return -ENOMEM;
 		break;
 	case V4L2_MEMORY_OVERLAY:
@@ -295,22 +293,18 @@
 	BUG_ON(!mem);
 	MAGIC_CHECK(mem->magic, MAGIC_DC_MEM);
 
-	if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(buf->bsize),
-				GFP_KERNEL | __GFP_COMP))
+	if (__videobuf_dc_alloc(q->dev, mem, PAGE_ALIGN(buf->bsize)))
 		goto error;
 
-	/* Try to remap memory */
-	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
-
 	/* the "vm_pgoff" is just used in v4l2 to find the
 	 * corresponding buffer data structure which is allocated
 	 * earlier and it does not mean the offset from the physical
 	 * buffer start address as usual. So set it to 0 to pass
-	 * the sanity check in vm_iomap_memory().
+	 * the sanity check in dma_mmap_coherent().
 	 */
 	vma->vm_pgoff = 0;
-
-	retval = vm_iomap_memory(vma, mem->dma_handle, mem->size);
+	retval = dma_mmap_coherent(q->dev, vma, mem->vaddr, mem->dma_handle,
+				   mem->size);
 	if (retval) {
 		dev_err(q->dev, "mmap: remap failed with error %d. ",
 			retval);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/Kconfig
@@ -168,7 +168,7 @@
 	  represents a coherency violation.
 
 config FSL_IFC
-	bool "Freescale IFC driver" if COMPILE_TEST
+	bool "Freescale IFC driver"
 	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST
 	depends on HAS_IOMEM
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/atmel-ebi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/atmel-ebi.c
@@ -544,20 +544,27 @@
 	smc_np = of_parse_phandle(dev->of_node, "atmel,smc", 0);
 
 	ebi->smc.regmap = syscon_node_to_regmap(smc_np);
-	if (IS_ERR(ebi->smc.regmap))
-		return PTR_ERR(ebi->smc.regmap);
+	if (IS_ERR(ebi->smc.regmap)) {
+		ret = PTR_ERR(ebi->smc.regmap);
+		goto put_node;
+	}
 
 	ebi->smc.layout = atmel_hsmc_get_reg_layout(smc_np);
-	if (IS_ERR(ebi->smc.layout))
-		return PTR_ERR(ebi->smc.layout);
+	if (IS_ERR(ebi->smc.layout)) {
+		ret = PTR_ERR(ebi->smc.layout);
+		goto put_node;
+	}
 
 	ebi->smc.clk = of_clk_get(smc_np, 0);
 	if (IS_ERR(ebi->smc.clk)) {
-		if (PTR_ERR(ebi->smc.clk) != -ENOENT)
-			return PTR_ERR(ebi->smc.clk);
+		if (PTR_ERR(ebi->smc.clk) != -ENOENT) {
+			ret = PTR_ERR(ebi->smc.clk);
+			goto put_node;
+		}
 
 		ebi->smc.clk = NULL;
 	}
+	of_node_put(smc_np);
 	ret = clk_prepare_enable(ebi->smc.clk);
 	if (ret)
 		return ret;
@@ -608,6 +615,10 @@
 	}
 
 	return of_platform_populate(np, NULL, NULL, dev);
+
+put_node:
+	of_node_put(smc_np);
+	return ret;
 }
 
 static __maybe_unused int atmel_ebi_resume(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/atmel-sdramc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/atmel-sdramc.c
@@ -47,19 +47,17 @@
 	caps = of_device_get_match_data(&pdev->dev);
 
 	if (caps->has_ddrck) {
-		clk = devm_clk_get(&pdev->dev, "ddrck");
+		clk = devm_clk_get_enabled(&pdev->dev, "ddrck");
 		if (IS_ERR(clk))
 			return PTR_ERR(clk);
-		clk_prepare_enable(clk);
 	}
 
 	if (caps->has_mpddr_clk) {
-		clk = devm_clk_get(&pdev->dev, "mpddr");
+		clk = devm_clk_get_enabled(&pdev->dev, "mpddr");
 		if (IS_ERR(clk)) {
 			pr_err("AT91 RAMC: couldn't get mpddr clock\n");
 			return PTR_ERR(clk);
 		}
-		clk_prepare_enable(clk);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/brcmstb_dpfe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/brcmstb_dpfe.c
@@ -434,15 +434,17 @@
 static int __send_command(struct brcmstb_dpfe_priv *priv, unsigned int cmd,
 			  u32 result[])
 {
-	const u32 *msg = priv->dpfe_api->command[cmd];
 	void __iomem *regs = priv->regs;
 	unsigned int i, chksum, chksum_idx;
+	const u32 *msg;
 	int ret = 0;
 	u32 resp;
 
 	if (cmd >= DPFE_CMD_MAX)
 		return -1;
 
+	msg = priv->dpfe_api->command[cmd];
+
 	mutex_lock(&priv->lock);
 
 	/* Wait for DCPU to become ready */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/emif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/emif.c
@@ -1025,7 +1025,7 @@
 	temp	= devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
 	dev_info = devm_kzalloc(dev, sizeof(*dev_info), GFP_KERNEL);
 
-	if (!emif || !pd || !dev_info) {
+	if (!emif || !temp || !dev_info) {
 		dev_err(dev, "%s:%d: allocation error\n", __func__, __LINE__);
 		goto error;
 	}
@@ -1117,7 +1117,7 @@
 {
 	struct emif_data	*emif;
 	struct resource		*res;
-	int			irq;
+	int			irq, ret;
 
 	if (pdev->dev.of_node)
 		emif = of_get_memory_device_details(pdev->dev.of_node, &pdev->dev);
@@ -1147,7 +1147,9 @@
 	emif_onetime_settings(emif);
 	emif_debugfs_init(emif);
 	disable_and_clear_all_interrupts(emif);
-	setup_interrupts(emif, irq);
+	ret = setup_interrupts(emif, irq);
+	if (ret)
+		goto error;
 
 	/* One-time actions taken on probing the first device */
 	if (!emif1) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/fsl_ifc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/fsl_ifc.c
@@ -263,7 +263,7 @@
 
 	ret = fsl_ifc_ctrl_init(fsl_ifc_ctrl_dev);
 	if (ret < 0)
-		goto err;
+		goto err_unmap_nandirq;
 
 	init_waitqueue_head(&fsl_ifc_ctrl_dev->nand_wait);
 
@@ -272,7 +272,7 @@
 	if (ret != 0) {
 		dev_err(&dev->dev, "failed to install irq (%d)\n",
 			fsl_ifc_ctrl_dev->irq);
-		goto err_irq;
+		goto err_unmap_nandirq;
 	}
 
 	if (fsl_ifc_ctrl_dev->nand_irq) {
@@ -281,17 +281,16 @@
 		if (ret != 0) {
 			dev_err(&dev->dev, "failed to install irq (%d)\n",
 				fsl_ifc_ctrl_dev->nand_irq);
-			goto err_nandirq;
+			goto err_free_irq;
 		}
 	}
 
 	return 0;
 
-err_nandirq:
-	free_irq(fsl_ifc_ctrl_dev->nand_irq, fsl_ifc_ctrl_dev);
-	irq_dispose_mapping(fsl_ifc_ctrl_dev->nand_irq);
-err_irq:
+err_free_irq:
 	free_irq(fsl_ifc_ctrl_dev->irq, fsl_ifc_ctrl_dev);
+err_unmap_nandirq:
+	irq_dispose_mapping(fsl_ifc_ctrl_dev->nand_irq);
 	irq_dispose_mapping(fsl_ifc_ctrl_dev->irq);
 err:
 	iounmap(fsl_ifc_ctrl_dev->gregs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/jedec_ddr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/jedec_ddr.h
@@ -112,6 +112,26 @@
 #define NUM_DDR_ADDR_TABLE_ENTRIES			11
 #define NUM_DDR_TIMING_TABLE_ENTRIES			4
 
+#define LPDDR2_MANID_SAMSUNG				1
+#define LPDDR2_MANID_QIMONDA				2
+#define LPDDR2_MANID_ELPIDA				3
+#define LPDDR2_MANID_ETRON				4
+#define LPDDR2_MANID_NANYA				5
+#define LPDDR2_MANID_HYNIX				6
+#define LPDDR2_MANID_MOSEL				7
+#define LPDDR2_MANID_WINBOND				8
+#define LPDDR2_MANID_ESMT				9
+#define LPDDR2_MANID_SPANSION				11
+#define LPDDR2_MANID_SST				12
+#define LPDDR2_MANID_ZMOS				13
+#define LPDDR2_MANID_INTEL				14
+#define LPDDR2_MANID_NUMONYX				254
+#define LPDDR2_MANID_MICRON				255
+
+#define LPDDR2_TYPE_S4					0
+#define LPDDR2_TYPE_S2					1
+#define LPDDR2_TYPE_NVM					2
+
 /* Structure for DDR addressing info from the JEDEC spec */
 struct lpddr2_addressing {
 	u32 num_banks;
@@ -170,6 +190,33 @@
 	lpddr2_jedec_timings[NUM_DDR_TIMING_TABLE_ENTRIES];
 extern const struct lpddr2_min_tck lpddr2_jedec_min_tck;
 
+/* Structure of MR8 */
+union lpddr2_basic_config4 {
+	u32 value;
+
+	struct {
+		unsigned int arch_type : 2;
+		unsigned int density : 4;
+		unsigned int io_width : 2;
+	} __packed;
+};
+
+/*
+ * Structure for information about LPDDR2 chip. All parameters are
+ * matching raw values of standard mode register bitfields or set to
+ * -ENOENT if info unavailable.
+ */
+struct lpddr2_info {
+	int arch_type;
+	int density;
+	int io_width;
+	int manufacturer_id;
+	int revision_id1;
+	int revision_id2;
+};
+
+const char *lpddr2_jedec_manufacturer(unsigned int manufacturer_id);
+
 /*
  * Structure for timings for LPDDR3 based on LPDDR2 plus additional fields.
  * All parameters are in pico seconds(ps) excluding max_freq, min_freq which
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/jedec_ddr_data.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/jedec_ddr_data.c
@@ -131,3 +131,44 @@
 	.tFAW		= 8
 };
 EXPORT_SYMBOL_GPL(lpddr2_jedec_min_tck);
+
+const char *lpddr2_jedec_manufacturer(unsigned int manufacturer_id)
+{
+	switch (manufacturer_id) {
+	case LPDDR2_MANID_SAMSUNG:
+		return "Samsung";
+	case LPDDR2_MANID_QIMONDA:
+		return "Qimonda";
+	case LPDDR2_MANID_ELPIDA:
+		return "Elpida";
+	case LPDDR2_MANID_ETRON:
+		return "Etron";
+	case LPDDR2_MANID_NANYA:
+		return "Nanya";
+	case LPDDR2_MANID_HYNIX:
+		return "Hynix";
+	case LPDDR2_MANID_MOSEL:
+		return "Mosel";
+	case LPDDR2_MANID_WINBOND:
+		return "Winbond";
+	case LPDDR2_MANID_ESMT:
+		return "ESMT";
+	case LPDDR2_MANID_SPANSION:
+		return "Spansion";
+	case LPDDR2_MANID_SST:
+		return "SST";
+	case LPDDR2_MANID_ZMOS:
+		return "ZMOS";
+	case LPDDR2_MANID_INTEL:
+		return "Intel";
+	case LPDDR2_MANID_NUMONYX:
+		return "Numonyx";
+	case LPDDR2_MANID_MICRON:
+		return "Micron";
+	default:
+		break;
+	}
+
+	return "invalid";
+}
+EXPORT_SYMBOL_GPL(lpddr2_jedec_manufacturer);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/mvebu-devbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/mvebu-devbus.c
@@ -280,10 +280,9 @@
 	if (IS_ERR(devbus->base))
 		return PTR_ERR(devbus->base);
 
-	clk = devm_clk_get(&pdev->dev, NULL);
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
-	clk_prepare_enable(clk);
 
 	/*
 	 * Obtain clock period in picoseconds,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/of_memory.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/of_memory.c
@@ -134,6 +134,7 @@
 	for_each_child_of_node(np_ddr, np_tim) {
 		if (of_device_is_compatible(np_tim, tim_compat)) {
 			if (of_do_get_timings(np_tim, &timings[i])) {
+				of_node_put(np_tim);
 				devm_kfree(dev, timings);
 				goto default_timings;
 			}
@@ -282,6 +283,7 @@
 		if (of_device_is_compatible(np_tim, tim_compat)) {
 			if (of_lpddr3_do_get_timings(np_tim, &timings[i])) {
 				devm_kfree(dev, timings);
+				of_node_put(np_tim);
 				goto default_timings;
 			}
 			i++;
@@ -298,3 +300,90 @@
 	return NULL;
 }
 EXPORT_SYMBOL(of_lpddr3_get_ddr_timings);
+
+/**
+ * of_lpddr2_get_info() - extracts information about the lpddr2 chip.
+ * @np: Pointer to device tree node containing lpddr2 info
+ * @dev: Device requesting info
+ *
+ * Populates lpddr2_info structure by extracting data from device
+ * tree node. Returns pointer to populated structure. If error
+ * happened while populating, returns NULL. If property is missing
+ * in a device-tree, then the corresponding value is set to -ENOENT.
+ */
+const struct lpddr2_info
+*of_lpddr2_get_info(struct device_node *np, struct device *dev)
+{
+	struct lpddr2_info *ret_info, info = {};
+	struct property *prop;
+	const char *cp;
+	int err;
+
+	err = of_property_read_u32(np, "revision-id1", &info.revision_id1);
+	if (err)
+		info.revision_id1 = -ENOENT;
+
+	err = of_property_read_u32(np, "revision-id2", &info.revision_id2);
+	if (err)
+		info.revision_id2 = -ENOENT;
+
+	err = of_property_read_u32(np, "io-width", &info.io_width);
+	if (err)
+		return NULL;
+
+	info.io_width = 32 / info.io_width - 1;
+
+	err = of_property_read_u32(np, "density", &info.density);
+	if (err)
+		return NULL;
+
+	info.density = ffs(info.density) - 7;
+
+	if (of_device_is_compatible(np, "jedec,lpddr2-s4"))
+		info.arch_type = LPDDR2_TYPE_S4;
+	else if (of_device_is_compatible(np, "jedec,lpddr2-s2"))
+		info.arch_type = LPDDR2_TYPE_S2;
+	else if (of_device_is_compatible(np, "jedec,lpddr2-nvm"))
+		info.arch_type = LPDDR2_TYPE_NVM;
+	else
+		return NULL;
+
+	prop = of_find_property(np, "compatible", NULL);
+	for (cp = of_prop_next_string(prop, NULL); cp;
+	     cp = of_prop_next_string(prop, cp)) {
+
+#define OF_LPDDR2_VENDOR_CMP(compat, ID) \
+		if (!of_compat_cmp(cp, compat ",", strlen(compat ","))) { \
+			info.manufacturer_id = LPDDR2_MANID_##ID; \
+			break; \
+		}
+
+		OF_LPDDR2_VENDOR_CMP("samsung", SAMSUNG)
+		OF_LPDDR2_VENDOR_CMP("qimonda", QIMONDA)
+		OF_LPDDR2_VENDOR_CMP("elpida", ELPIDA)
+		OF_LPDDR2_VENDOR_CMP("etron", ETRON)
+		OF_LPDDR2_VENDOR_CMP("nanya", NANYA)
+		OF_LPDDR2_VENDOR_CMP("hynix", HYNIX)
+		OF_LPDDR2_VENDOR_CMP("mosel", MOSEL)
+		OF_LPDDR2_VENDOR_CMP("winbond", WINBOND)
+		OF_LPDDR2_VENDOR_CMP("esmt", ESMT)
+		OF_LPDDR2_VENDOR_CMP("spansion", SPANSION)
+		OF_LPDDR2_VENDOR_CMP("sst", SST)
+		OF_LPDDR2_VENDOR_CMP("zmos", ZMOS)
+		OF_LPDDR2_VENDOR_CMP("intel", INTEL)
+		OF_LPDDR2_VENDOR_CMP("numonyx", NUMONYX)
+		OF_LPDDR2_VENDOR_CMP("micron", MICRON)
+
+#undef OF_LPDDR2_VENDOR_CMP
+	}
+
+	if (!info.manufacturer_id)
+		info.manufacturer_id = -ENOENT;
+
+	ret_info = devm_kzalloc(dev, sizeof(*ret_info), GFP_KERNEL);
+	if (ret_info)
+		*ret_info = info;
+
+	return ret_info;
+}
+EXPORT_SYMBOL(of_lpddr2_get_info);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/of_memory.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/of_memory.h
@@ -20,6 +20,9 @@
 const struct lpddr3_timings *
 of_lpddr3_get_ddr_timings(struct device_node *np_ddr,
 			  struct device *dev, u32 device_type, u32 *nr_frequencies);
+
+const struct lpddr2_info *of_lpddr2_get_info(struct device_node *np,
+					     struct device *dev);
 #else
 static inline const struct lpddr2_min_tck
 	*of_get_min_tck(struct device_node *np, struct device *dev)
@@ -46,6 +49,12 @@
 {
 	return NULL;
 }
+
+static inline const struct lpddr2_info
+	*of_lpddr2_get_info(struct device_node *np, struct device *dev)
+{
+	return NULL;
+}
 #endif /* CONFIG_OF && CONFIG_DDR */
 
 #endif /* __LINUX_MEMORY_OF_REG_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/pl353-smc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/pl353-smc.c
@@ -122,6 +122,7 @@
 	}
 
 	of_platform_device_create(child, NULL, &adev->dev);
+	of_node_put(child);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/renesas-rpc-if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/renesas-rpc-if.c
@@ -160,10 +160,91 @@
 	.n_yes_ranges	= ARRAY_SIZE(rpcif_volatile_ranges),
 };
 
+
+/*
+ * Custom accessor functions to ensure SM[RW]DR[01] are always accessed with
+ * proper width.  Requires rpcif.xfer_size to be correctly set before!
+ */
+static int rpcif_reg_read(void *context, unsigned int reg, unsigned int *val)
+{
+	struct rpcif *rpc = context;
+
+	switch (reg) {
+	case RPCIF_SMRDR0:
+	case RPCIF_SMWDR0:
+		switch (rpc->xfer_size) {
+		case 1:
+			*val = readb(rpc->base + reg);
+			return 0;
+
+		case 2:
+			*val = readw(rpc->base + reg);
+			return 0;
+
+		case 4:
+		case 8:
+			*val = readl(rpc->base + reg);
+			return 0;
+
+		default:
+			return -EILSEQ;
+		}
+
+	case RPCIF_SMRDR1:
+	case RPCIF_SMWDR1:
+		if (rpc->xfer_size != 8)
+			return -EILSEQ;
+		break;
+	}
+
+	*val = readl(rpc->base + reg);
+	return 0;
+}
+
+static int rpcif_reg_write(void *context, unsigned int reg, unsigned int val)
+{
+	struct rpcif *rpc = context;
+
+	switch (reg) {
+	case RPCIF_SMWDR0:
+		switch (rpc->xfer_size) {
+		case 1:
+			writeb(val, rpc->base + reg);
+			return 0;
+
+		case 2:
+			writew(val, rpc->base + reg);
+			return 0;
+
+		case 4:
+		case 8:
+			writel(val, rpc->base + reg);
+			return 0;
+
+		default:
+			return -EILSEQ;
+		}
+
+	case RPCIF_SMWDR1:
+		if (rpc->xfer_size != 8)
+			return -EILSEQ;
+		break;
+
+	case RPCIF_SMRDR0:
+	case RPCIF_SMRDR1:
+		return -EPERM;
+	}
+
+	writel(val, rpc->base + reg);
+	return 0;
+}
+
 static const struct regmap_config rpcif_regmap_config = {
 	.reg_bits	= 32,
 	.val_bits	= 32,
 	.reg_stride	= 4,
+	.reg_read	= rpcif_reg_read,
+	.reg_write	= rpcif_reg_write,
 	.fast_io	= true,
 	.max_register	= RPCIF_PHYINT,
 	.volatile_table	= &rpcif_volatile_table,
@@ -173,17 +254,15 @@
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct resource *res;
-	void __iomem *base;
 
 	rpc->dev = dev;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
-	base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(base))
-		return PTR_ERR(base);
+	rpc->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rpc->base))
+		return PTR_ERR(rpc->base);
 
-	rpc->regmap = devm_regmap_init_mmio(&pdev->dev, base,
-					    &rpcif_regmap_config);
+	rpc->regmap = devm_regmap_init(&pdev->dev, NULL, rpc, &rpcif_regmap_config);
 	if (IS_ERR(rpc->regmap)) {
 		dev_err(&pdev->dev,
 			"failed to init regmap for rpcif, error %ld\n",
@@ -194,7 +273,7 @@
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dirmap");
 	rpc->dirmap = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(rpc->dirmap))
-		rpc->dirmap = NULL;
+		return PTR_ERR(rpc->dirmap);
 	rpc->size = resource_size(res);
 
 	rpc->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
@@ -354,20 +433,16 @@
 			nbytes = op->data.nbytes;
 		rpc->xferlen = nbytes;
 
-		rpc->enable |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes)) |
-			RPCIF_SMENR_SPIDB(rpcif_bit_size(op->data.buswidth));
+		rpc->enable |= RPCIF_SMENR_SPIDB(rpcif_bit_size(op->data.buswidth));
 	}
 }
 EXPORT_SYMBOL(rpcif_prepare);
 
 int rpcif_manual_xfer(struct rpcif *rpc)
 {
-	u32 smenr, smcr, pos = 0, max = 4;
+	u32 smenr, smcr, pos = 0, max = rpc->bus_size == 2 ? 8 : 4;
 	int ret = 0;
 
-	if (rpc->bus_size == 2)
-		max = 8;
-
 	pm_runtime_get_sync(rpc->dev);
 
 	regmap_update_bits(rpc->regmap, RPCIF_PHYCNT,
@@ -378,37 +453,37 @@
 	regmap_write(rpc->regmap, RPCIF_SMOPR, rpc->option);
 	regmap_write(rpc->regmap, RPCIF_SMDMCR, rpc->dummy);
 	regmap_write(rpc->regmap, RPCIF_SMDRENR, rpc->ddr);
+	regmap_write(rpc->regmap, RPCIF_SMADR, rpc->smadr);
 	smenr = rpc->enable;
 
 	switch (rpc->dir) {
 	case RPCIF_DATA_OUT:
 		while (pos < rpc->xferlen) {
-			u32 nbytes = rpc->xferlen - pos;
-			u32 data[2];
+			u32 bytes_left = rpc->xferlen - pos;
+			u32 nbytes, data[2];
 
 			smcr = rpc->smcr | RPCIF_SMCR_SPIE;
-			if (nbytes > max) {
-				nbytes = max;
+
+			/* nbytes may only be 1, 2, 4, or 8 */
+			nbytes = bytes_left >= max ? max : (1 << ilog2(bytes_left));
+			if (bytes_left > nbytes)
 				smcr |= RPCIF_SMCR_SSLKP;
-			}
+
+			smenr |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes));
+			regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
+			rpc->xfer_size = nbytes;
 
 			memcpy(data, rpc->buffer + pos, nbytes);
-			if (nbytes > 4) {
+			if (nbytes == 8) {
 				regmap_write(rpc->regmap, RPCIF_SMWDR1,
 					     data[0]);
 				regmap_write(rpc->regmap, RPCIF_SMWDR0,
 					     data[1]);
-			} else if (nbytes > 2) {
+			} else {
 				regmap_write(rpc->regmap, RPCIF_SMWDR0,
 					     data[0]);
-			} else	{
-				regmap_write(rpc->regmap, RPCIF_SMWDR0,
-					     data[0] << 16);
 			}
 
-			regmap_write(rpc->regmap, RPCIF_SMADR,
-				     rpc->smadr + pos);
-			regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
 			regmap_write(rpc->regmap, RPCIF_SMCR, smcr);
 			ret = wait_msg_xfer_end(rpc);
 			if (ret)
@@ -448,33 +523,32 @@
 			break;
 		}
 		while (pos < rpc->xferlen) {
-			u32 nbytes = rpc->xferlen - pos;
-			u32 data[2];
+			u32 bytes_left = rpc->xferlen - pos;
+			u32 nbytes, data[2];
 
-			if (nbytes > max)
-				nbytes = max;
+			/* nbytes may only be 1, 2, 4, or 8 */
+			nbytes = bytes_left >= max ? max : (1 << ilog2(bytes_left));
 
 			regmap_write(rpc->regmap, RPCIF_SMADR,
 				     rpc->smadr + pos);
+			smenr &= ~RPCIF_SMENR_SPIDE(0xF);
+			smenr |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes));
 			regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
 			regmap_write(rpc->regmap, RPCIF_SMCR,
 				     rpc->smcr | RPCIF_SMCR_SPIE);
+			rpc->xfer_size = nbytes;
 			ret = wait_msg_xfer_end(rpc);
 			if (ret)
 				goto err_out;
 
-			if (nbytes > 4) {
+			if (nbytes == 8) {
 				regmap_read(rpc->regmap, RPCIF_SMRDR1,
 					    &data[0]);
 				regmap_read(rpc->regmap, RPCIF_SMRDR0,
 					    &data[1]);
-			} else if (nbytes > 2) {
+			} else {
 				regmap_read(rpc->regmap, RPCIF_SMRDR0,
 					    &data[0]);
-			} else	{
-				regmap_read(rpc->regmap, RPCIF_SMRDR0,
-					    &data[0]);
-				data[0] >>= 16;
 			}
 			memcpy(rpc->buffer + pos, data, nbytes);
 
@@ -502,6 +576,48 @@
 }
 EXPORT_SYMBOL(rpcif_manual_xfer);
 
+static void memcpy_fromio_readw(void *to,
+				const void __iomem *from,
+				size_t count)
+{
+	const int maxw = (IS_ENABLED(CONFIG_64BIT)) ? 8 : 4;
+	u8 buf[2];
+
+	if (count && ((unsigned long)from & 1)) {
+		*(u16 *)buf = __raw_readw((void __iomem *)((unsigned long)from & ~1));
+		*(u8 *)to = buf[1];
+		from++;
+		to++;
+		count--;
+	}
+	while (count >= 2 && !IS_ALIGNED((unsigned long)from, maxw)) {
+		*(u16 *)to = __raw_readw(from);
+		from += 2;
+		to += 2;
+		count -= 2;
+	}
+	while (count >= maxw) {
+#ifdef CONFIG_64BIT
+		*(u64 *)to = __raw_readq(from);
+#else
+		*(u32 *)to = __raw_readl(from);
+#endif
+		from += maxw;
+		to += maxw;
+		count -= maxw;
+	}
+	while (count >= 2) {
+		*(u16 *)to = __raw_readw(from);
+		from += 2;
+		to += 2;
+		count -= 2;
+	}
+	if (count) {
+		*(u16 *)buf = __raw_readw(from);
+		*(u8 *)to = buf[0];
+	}
+}
+
 ssize_t rpcif_dirmap_read(struct rpcif *rpc, u64 offs, size_t len, void *buf)
 {
 	loff_t from = offs & (RPCIF_DIRMAP_SIZE - 1);
@@ -523,7 +639,10 @@
 	regmap_write(rpc->regmap, RPCIF_DRDMCR, rpc->dummy);
 	regmap_write(rpc->regmap, RPCIF_DRDRENR, rpc->ddr);
 
-	memcpy_fromio(buf, rpc->dirmap + from, len);
+	if (rpc->bus_size == 2)
+		memcpy_fromio_readw(buf, rpc->dirmap + from, len);
+	else
+		memcpy_fromio(buf, rpc->dirmap + from, len);
 
 	pm_runtime_put(rpc->dev);
 
@@ -536,6 +655,7 @@
 	struct platform_device *vdev;
 	struct device_node *flash;
 	const char *name;
+	int ret;
 
 	flash = of_get_next_child(pdev->dev.of_node, NULL);
 	if (!flash) {
@@ -559,7 +679,14 @@
 		return -ENOMEM;
 	vdev->dev.parent = &pdev->dev;
 	platform_set_drvdata(pdev, vdev);
-	return platform_device_add(vdev);
+
+	ret = platform_device_add(vdev);
+	if (ret) {
+		platform_device_put(vdev);
+		return ret;
+	}
+
+	return 0;
 }
 
 static int rpcif_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/samsung/exynos5422-dmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/samsung/exynos5422-dmc.c
@@ -1187,33 +1187,39 @@
 
 	dmc->timing_row = devm_kmalloc_array(dmc->dev, TIMING_COUNT,
 					     sizeof(u32), GFP_KERNEL);
-	if (!dmc->timing_row)
-		return -ENOMEM;
+	if (!dmc->timing_row) {
+		ret = -ENOMEM;
+		goto put_node;
+	}
 
 	dmc->timing_data = devm_kmalloc_array(dmc->dev, TIMING_COUNT,
 					      sizeof(u32), GFP_KERNEL);
-	if (!dmc->timing_data)
-		return -ENOMEM;
+	if (!dmc->timing_data) {
+		ret = -ENOMEM;
+		goto put_node;
+	}
 
 	dmc->timing_power = devm_kmalloc_array(dmc->dev, TIMING_COUNT,
 					       sizeof(u32), GFP_KERNEL);
-	if (!dmc->timing_power)
-		return -ENOMEM;
+	if (!dmc->timing_power) {
+		ret = -ENOMEM;
+		goto put_node;
+	}
 
 	dmc->timings = of_lpddr3_get_ddr_timings(np_ddr, dmc->dev,
 						 DDR_TYPE_LPDDR3,
 						 &dmc->timings_arr_size);
 	if (!dmc->timings) {
-		of_node_put(np_ddr);
 		dev_warn(dmc->dev, "could not get timings from DT\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_node;
 	}
 
 	dmc->min_tck = of_lpddr3_get_min_tck(np_ddr, dmc->dev);
 	if (!dmc->min_tck) {
-		of_node_put(np_ddr);
 		dev_warn(dmc->dev, "could not get tck from DT\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_node;
 	}
 
 	/* Sorted array of OPPs with frequency ascending */
@@ -1227,13 +1233,14 @@
 					     clk_period_ps);
 	}
 
-	of_node_put(np_ddr);
 
 	/* Take the highest frequency's timings as 'bypass' */
 	dmc->bypass_timing_row = dmc->timing_row[idx - 1];
 	dmc->bypass_timing_data = dmc->timing_data[idx - 1];
 	dmc->bypass_timing_power = dmc->timing_power[idx - 1];
 
+put_node:
+	of_node_put(np_ddr);
 	return ret;
 }
 
@@ -1322,7 +1329,6 @@
  */
 static int exynos5_performance_counters_init(struct exynos5_dmc *dmc)
 {
-	int counters_size;
 	int ret, i;
 
 	dmc->num_counters = devfreq_event_get_edev_count(dmc->dev,
@@ -1332,8 +1338,8 @@
 		return dmc->num_counters;
 	}
 
-	counters_size = sizeof(struct devfreq_event_dev) * dmc->num_counters;
-	dmc->counter = devm_kzalloc(dmc->dev, counters_size, GFP_KERNEL);
+	dmc->counter = devm_kcalloc(dmc->dev, dmc->num_counters,
+				    sizeof(*dmc->counter), GFP_KERNEL);
 	if (!dmc->counter)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/stm32-fmc2-ebi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/stm32-fmc2-ebi.c
@@ -179,8 +179,11 @@
 				    int cs)
 {
 	u32 bcr;
+	int ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
 
 	if (bcr & FMC2_BCR_MTYP)
 		return 0;
@@ -193,8 +196,11 @@
 					int cs)
 {
 	u32 bcr, val = FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+	int ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
 
 	if ((bcr & FMC2_BCR_MTYP) == val && bcr & FMC2_BCR_BURSTEN)
 		return 0;
@@ -207,8 +213,11 @@
 					   int cs)
 {
 	u32 bcr;
+	int ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
 
 	if (bcr & FMC2_BCR_BURSTEN)
 		return 0;
@@ -221,8 +230,11 @@
 					    int cs)
 {
 	u32 bcr;
+	int ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
 
 	if (!(bcr & FMC2_BCR_BURSTEN) || !(bcr & FMC2_BCR_CBURSTRW))
 		return 0;
@@ -235,8 +247,11 @@
 				       int cs)
 {
 	u32 bcr, val = FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_PSRAM);
+	int ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
 
 	if ((bcr & FMC2_BCR_MTYP) == val && bcr & FMC2_BCR_BURSTEN)
 		return 0;
@@ -249,12 +264,18 @@
 					     int cs)
 {
 	u32 bcr, bxtr, val = FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_D);
+	int ret;
+
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
 	if (prop->reg_type == FMC2_REG_BWTR)
-		regmap_read(ebi->regmap, FMC2_BWTR(cs), &bxtr);
+		ret = regmap_read(ebi->regmap, FMC2_BWTR(cs), &bxtr);
 	else
-		regmap_read(ebi->regmap, FMC2_BTR(cs), &bxtr);
+		ret = regmap_read(ebi->regmap, FMC2_BTR(cs), &bxtr);
+	if (ret)
+		return ret;
 
 	if ((!(bcr & FMC2_BCR_BURSTEN) || !(bcr & FMC2_BCR_CBURSTRW)) &&
 	    ((bxtr & FMC2_BXTR_ACCMOD) == val || bcr & FMC2_BCR_MUXEN))
@@ -268,12 +289,19 @@
 					   int cs)
 {
 	u32 bcr, bcr1;
+	int ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
-	if (cs)
-		regmap_read(ebi->regmap, FMC2_BCR1, &bcr1);
-	else
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
+
+	if (cs) {
+		ret = regmap_read(ebi->regmap, FMC2_BCR1, &bcr1);
+		if (ret)
+			return ret;
+	} else {
 		bcr1 = bcr;
+	}
 
 	if (bcr & FMC2_BCR_BURSTEN && (!cs || !(bcr1 & FMC2_BCR1_CCLKEN)))
 		return 0;
@@ -305,12 +333,18 @@
 {
 	u32 nb_clk_cycles = stm32_fmc2_ebi_ns_to_clock_cycles(ebi, cs, setup);
 	u32 bcr, btr, clk_period;
+	int ret;
+
+	ret = regmap_read(ebi->regmap, FMC2_BCR1, &bcr);
+	if (ret)
+		return ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR1, &bcr);
 	if (bcr & FMC2_BCR1_CCLKEN || !cs)
-		regmap_read(ebi->regmap, FMC2_BTR1, &btr);
+		ret = regmap_read(ebi->regmap, FMC2_BTR1, &btr);
 	else
-		regmap_read(ebi->regmap, FMC2_BTR(cs), &btr);
+		ret = regmap_read(ebi->regmap, FMC2_BTR(cs), &btr);
+	if (ret)
+		return ret;
 
 	clk_period = FIELD_GET(FMC2_BTR_CLKDIV, btr) + 1;
 
@@ -569,11 +603,16 @@
 	if (ret)
 		return ret;
 
-	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (ret)
+		return ret;
+
 	if (prop->reg_type == FMC2_REG_BWTR)
-		regmap_read(ebi->regmap, FMC2_BWTR(cs), &bxtr);
+		ret = regmap_read(ebi->regmap, FMC2_BWTR(cs), &bxtr);
 	else
-		regmap_read(ebi->regmap, FMC2_BTR(cs), &bxtr);
+		ret = regmap_read(ebi->regmap, FMC2_BTR(cs), &bxtr);
+	if (ret)
+		return ret;
 
 	if ((bxtr & FMC2_BXTR_ACCMOD) == val || bcr & FMC2_BCR_MUXEN)
 		val = clamp_val(setup, 1, FMC2_BXTR_ADDSET_MAX);
@@ -691,11 +730,14 @@
 					    int cs, u32 setup)
 {
 	u32 old_val, new_val, pcscntr;
+	int ret;
 
 	if (setup < 1)
 		return 0;
 
-	regmap_read(ebi->regmap, FMC2_PCSCNTR, &pcscntr);
+	ret = regmap_read(ebi->regmap, FMC2_PCSCNTR, &pcscntr);
+	if (ret)
+		return ret;
 
 	/* Enable counter for the bank */
 	regmap_update_bits(ebi->regmap, FMC2_PCSCNTR,
@@ -942,17 +984,20 @@
 	regmap_update_bits(ebi->regmap, FMC2_BCR(cs), FMC2_BCR_MBKEN, 0);
 }
 
-static void stm32_fmc2_ebi_save_setup(struct stm32_fmc2_ebi *ebi)
+static int stm32_fmc2_ebi_save_setup(struct stm32_fmc2_ebi *ebi)
 {
 	unsigned int cs;
+	int ret;
 
 	for (cs = 0; cs < FMC2_MAX_EBI_CE; cs++) {
-		regmap_read(ebi->regmap, FMC2_BCR(cs), &ebi->bcr[cs]);
-		regmap_read(ebi->regmap, FMC2_BTR(cs), &ebi->btr[cs]);
-		regmap_read(ebi->regmap, FMC2_BWTR(cs), &ebi->bwtr[cs]);
+		ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &ebi->bcr[cs]);
+		ret |= regmap_read(ebi->regmap, FMC2_BTR(cs), &ebi->btr[cs]);
+		ret |= regmap_read(ebi->regmap, FMC2_BWTR(cs), &ebi->bwtr[cs]);
+		if (ret)
+			return ret;
 	}
 
-	regmap_read(ebi->regmap, FMC2_PCSCNTR, &ebi->pcscntr);
+	return regmap_read(ebi->regmap, FMC2_PCSCNTR, &ebi->pcscntr);
 }
 
 static void stm32_fmc2_ebi_set_setup(struct stm32_fmc2_ebi *ebi)
@@ -981,22 +1026,29 @@
 }
 
 /* NWAIT signal can not be connected to EBI controller and NAND controller */
-static bool stm32_fmc2_ebi_nwait_used_by_ctrls(struct stm32_fmc2_ebi *ebi)
+static int stm32_fmc2_ebi_nwait_used_by_ctrls(struct stm32_fmc2_ebi *ebi)
 {
+	struct device *dev = ebi->dev;
 	unsigned int cs;
 	u32 bcr;
+	int ret;
 
 	for (cs = 0; cs < FMC2_MAX_EBI_CE; cs++) {
 		if (!(ebi->bank_assigned & BIT(cs)))
 			continue;
 
-		regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+		ret = regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+		if (ret)
+			return ret;
+
 		if ((bcr & FMC2_BCR_WAITEN || bcr & FMC2_BCR_ASYNCWAIT) &&
-		    ebi->bank_assigned & BIT(FMC2_NAND))
-			return true;
+		    ebi->bank_assigned & BIT(FMC2_NAND)) {
+			dev_err(dev, "NWAIT signal connected to EBI and NAND controllers\n");
+			return -EINVAL;
+		}
 	}
 
-	return false;
+	return 0;
 }
 
 static void stm32_fmc2_ebi_enable(struct stm32_fmc2_ebi *ebi)
@@ -1083,10 +1135,9 @@
 		return -ENODEV;
 	}
 
-	if (stm32_fmc2_ebi_nwait_used_by_ctrls(ebi)) {
-		dev_err(dev, "NWAIT signal connected to EBI and NAND controllers\n");
-		return -EINVAL;
-	}
+	ret = stm32_fmc2_ebi_nwait_used_by_ctrls(ebi);
+	if (ret)
+		return ret;
 
 	stm32_fmc2_ebi_enable(ebi);
 
@@ -1131,7 +1182,10 @@
 	if (ret)
 		goto err_release;
 
-	stm32_fmc2_ebi_save_setup(ebi);
+	ret = stm32_fmc2_ebi_save_setup(ebi);
+	if (ret)
+		goto err_release;
+
 	platform_set_drvdata(pdev, ebi);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/tegra/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/tegra/Kconfig
@@ -16,6 +16,7 @@
 	depends on ARCH_TEGRA_2x_SOC || COMPILE_TEST
 	select DEVFREQ_GOV_SIMPLE_ONDEMAND
 	select PM_DEVFREQ
+	select DDR
 	help
 	  This driver is for the External Memory Controller (EMC) found on
 	  Tegra20 chips. The EMC controls the external DRAM on the board.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/tegra/tegra186.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/tegra/tegra186.c
@@ -20,32 +20,6 @@
 #define MC_SID_STREAMID_SECURITY_WRITE_ACCESS_DISABLED BIT(16)
 #define MC_SID_STREAMID_SECURITY_OVERRIDE BIT(8)
 
-static void tegra186_mc_program_sid(struct tegra_mc *mc)
-{
-	unsigned int i;
-
-	for (i = 0; i < mc->soc->num_clients; i++) {
-		const struct tegra_mc_client *client = &mc->soc->clients[i];
-		u32 override, security;
-
-		override = readl(mc->regs + client->regs.sid.override);
-		security = readl(mc->regs + client->regs.sid.security);
-
-		dev_dbg(mc->dev, "client %s: override: %x security: %x\n",
-			client->name, override, security);
-
-		dev_dbg(mc->dev, "setting SID %u for %s\n", client->sid,
-			client->name);
-		writel(client->sid, mc->regs + client->regs.sid.override);
-
-		override = readl(mc->regs + client->regs.sid.override);
-		security = readl(mc->regs + client->regs.sid.security);
-
-		dev_dbg(mc->dev, "client %s: override: %x security: %x\n",
-			client->name, override, security);
-	}
-}
-
 static int tegra186_mc_probe(struct tegra_mc *mc)
 {
 	int err;
@@ -54,8 +28,6 @@
 	if (err < 0)
 		return err;
 
-	tegra186_mc_program_sid(mc);
-
 	return 0;
 }
 
@@ -64,13 +36,6 @@
 	of_platform_depopulate(mc->dev);
 }
 
-static int tegra186_mc_resume(struct tegra_mc *mc)
-{
-	tegra186_mc_program_sid(mc);
-
-	return 0;
-}
-
 #if IS_ENABLED(CONFIG_IOMMU_API)
 static void tegra186_mc_client_sid_override(struct tegra_mc *mc,
 					    const struct tegra_mc_client *client,
@@ -78,6 +43,9 @@
 {
 	u32 value, old;
 
+	if (client->regs.sid.security == 0 && client->regs.sid.override == 0)
+		return;
+
 	value = readl(mc->regs + client->regs.sid.security);
 	if ((value & MC_SID_STREAMID_SECURITY_OVERRIDE) == 0) {
 		/*
@@ -142,7 +110,6 @@
 const struct tegra_mc_ops tegra186_mc_ops = {
 	.probe = tegra186_mc_probe,
 	.remove = tegra186_mc_remove,
-	.resume = tegra186_mc_resume,
 	.probe_device = tegra186_mc_probe_device,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memory/tegra/tegra20-emc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memory/tegra/tegra20-emc.c
@@ -5,6 +5,7 @@
  * Author: Dmitry Osipenko <digetx@gmail.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/clk/tegra.h>
 #include <linux/debugfs.h>
@@ -27,11 +28,15 @@
 #include <soc/tegra/common.h>
 #include <soc/tegra/fuse.h>
 
+#include "../jedec_ddr.h"
+#include "../of_memory.h"
+
 #include "mc.h"
 
 #define EMC_INTSTATUS				0x000
 #define EMC_INTMASK				0x004
 #define EMC_DBG					0x008
+#define EMC_ADR_CFG_0				0x010
 #define EMC_TIMING_CONTROL			0x028
 #define EMC_RC					0x02c
 #define EMC_RFC					0x030
@@ -68,6 +73,7 @@
 #define EMC_QUSE_EXTRA				0x0ac
 #define EMC_ODT_WRITE				0x0b0
 #define EMC_ODT_READ				0x0b4
+#define EMC_MRR					0x0ec
 #define EMC_FBIO_CFG5				0x104
 #define EMC_FBIO_CFG6				0x114
 #define EMC_STAT_CONTROL			0x160
@@ -94,6 +100,7 @@
 
 #define EMC_REFRESH_OVERFLOW_INT		BIT(3)
 #define EMC_CLKCHANGE_COMPLETE_INT		BIT(4)
+#define EMC_MRR_DIVLD_INT			BIT(5)
 
 #define EMC_DBG_READ_MUX_ASSEMBLY		BIT(0)
 #define EMC_DBG_WRITE_MUX_ACTIVE		BIT(1)
@@ -102,11 +109,25 @@
 #define EMC_DBG_CFG_PRIORITY			BIT(24)
 
 #define EMC_FBIO_CFG5_DRAM_WIDTH_X16		BIT(4)
+#define EMC_FBIO_CFG5_DRAM_TYPE			GENMASK(1, 0)
+
+#define EMC_MRR_DEV_SELECTN			GENMASK(31, 30)
+#define EMC_MRR_MRR_MA				GENMASK(23, 16)
+#define EMC_MRR_MRR_DATA			GENMASK(15, 0)
+
+#define EMC_ADR_CFG_0_EMEM_NUMDEV		GENMASK(25, 24)
 
 #define EMC_PWR_GATHER_CLEAR			(1 << 8)
 #define EMC_PWR_GATHER_DISABLE			(2 << 8)
 #define EMC_PWR_GATHER_ENABLE			(3 << 8)
 
+enum emc_dram_type {
+	DRAM_TYPE_RESERVED,
+	DRAM_TYPE_DDR1,
+	DRAM_TYPE_LPDDR2,
+	DRAM_TYPE_DDR2,
+};
+
 static const u16 emc_timing_registers[] = {
 	EMC_RC,
 	EMC_RFC,
@@ -201,6 +222,14 @@
 	struct mutex rate_lock;
 
 	struct devfreq_simple_ondemand_data ondemand_data;
+
+	/* memory chip identity information */
+	union lpddr2_basic_config4 basic_conf4;
+	unsigned int manufacturer_id;
+	unsigned int revision_id1;
+	unsigned int revision_id2;
+
+	bool mrr_error;
 };
 
 static irqreturn_t tegra_emc_isr(int irq, void *data)
@@ -397,15 +426,19 @@
 	if (!emc->timings)
 		return -ENOMEM;
 
-	emc->num_timings = child_count;
 	timing = emc->timings;
 
 	for_each_child_of_node(node, child) {
+		if (of_node_name_eq(child, "lpddr2"))
+			continue;
+
 		err = load_one_timing_from_dt(emc, timing++, child);
 		if (err) {
 			of_node_put(child);
 			return err;
 		}
+
+		emc->num_timings++;
 	}
 
 	sort(emc->timings, emc->num_timings, sizeof(*timing), cmp_timings,
@@ -422,12 +455,18 @@
 }
 
 static struct device_node *
-tegra_emc_find_node_by_ram_code(struct device *dev)
+tegra_emc_find_node_by_ram_code(struct tegra_emc *emc)
 {
+	struct device *dev = emc->dev;
 	struct device_node *np;
 	u32 value, ram_code;
 	int err;
 
+	if (emc->mrr_error) {
+		dev_warn(dev, "memory timings skipped due to MRR error\n");
+		return NULL;
+	}
+
 	if (of_get_child_count(dev->of_node) == 0) {
 		dev_info_once(dev, "device-tree doesn't have memory timings\n");
 		return NULL;
@@ -438,12 +477,53 @@
 
 	ram_code = tegra_read_ram_code();
 
-	for (np = of_find_node_by_name(dev->of_node, "emc-tables"); np;
-	     np = of_find_node_by_name(np, "emc-tables")) {
+	for_each_child_of_node(dev->of_node, np) {
+		if (!of_node_name_eq(np, "emc-tables"))
+			continue;
 		err = of_property_read_u32(np, "nvidia,ram-code", &value);
 		if (err || value != ram_code) {
-			of_node_put(np);
-			continue;
+			struct device_node *lpddr2_np;
+			bool cfg_mismatches = false;
+
+			lpddr2_np = of_get_child_by_name(np, "lpddr2");
+			if (lpddr2_np) {
+				const struct lpddr2_info *info;
+
+				info = of_lpddr2_get_info(lpddr2_np, dev);
+				if (info) {
+					if (info->manufacturer_id >= 0 &&
+					    info->manufacturer_id != emc->manufacturer_id)
+						cfg_mismatches = true;
+
+					if (info->revision_id1 >= 0 &&
+					    info->revision_id1 != emc->revision_id1)
+						cfg_mismatches = true;
+
+					if (info->revision_id2 >= 0 &&
+					    info->revision_id2 != emc->revision_id2)
+						cfg_mismatches = true;
+
+					if (info->density != emc->basic_conf4.density)
+						cfg_mismatches = true;
+
+					if (info->io_width != emc->basic_conf4.io_width)
+						cfg_mismatches = true;
+
+					if (info->arch_type != emc->basic_conf4.arch_type)
+						cfg_mismatches = true;
+				} else {
+					dev_err(dev, "failed to parse %pOF\n", lpddr2_np);
+					cfg_mismatches = true;
+				}
+
+				of_node_put(lpddr2_np);
+			} else {
+				cfg_mismatches = true;
+			}
+
+			if (cfg_mismatches) {
+				continue;
+			}
 		}
 
 		return np;
@@ -455,10 +535,72 @@
 	return NULL;
 }
 
+static int emc_read_lpddr_mode_register(struct tegra_emc *emc,
+					unsigned int emem_dev,
+					unsigned int register_addr,
+					unsigned int *register_data)
+{
+	u32 memory_dev = emem_dev ? 1 : 2;
+	u32 val, mr_mask = 0xff;
+	int err;
+
+	/* clear data-valid interrupt status */
+	writel_relaxed(EMC_MRR_DIVLD_INT, emc->regs + EMC_INTSTATUS);
+
+	/* issue mode register read request */
+	val  = FIELD_PREP(EMC_MRR_DEV_SELECTN, memory_dev);
+	val |= FIELD_PREP(EMC_MRR_MRR_MA, register_addr);
+
+	writel_relaxed(val, emc->regs + EMC_MRR);
+
+	/* wait for the LPDDR2 data-valid interrupt */
+	err = readl_relaxed_poll_timeout_atomic(emc->regs + EMC_INTSTATUS, val,
+						val & EMC_MRR_DIVLD_INT,
+						1, 100);
+	if (err) {
+		dev_err(emc->dev, "mode register %u read failed: %d\n",
+			register_addr, err);
+		emc->mrr_error = true;
+		return err;
+	}
+
+	/* read out mode register data */
+	val = readl_relaxed(emc->regs + EMC_MRR);
+	*register_data = FIELD_GET(EMC_MRR_MRR_DATA, val) & mr_mask;
+
+	return 0;
+}
+
+static void emc_read_lpddr_sdram_info(struct tegra_emc *emc,
+				      unsigned int emem_dev,
+				      bool print_out)
+{
+	/* these registers are standard for all LPDDR JEDEC memory chips */
+	emc_read_lpddr_mode_register(emc, emem_dev, 5, &emc->manufacturer_id);
+	emc_read_lpddr_mode_register(emc, emem_dev, 6, &emc->revision_id1);
+	emc_read_lpddr_mode_register(emc, emem_dev, 7, &emc->revision_id2);
+	emc_read_lpddr_mode_register(emc, emem_dev, 8, &emc->basic_conf4.value);
+
+	if (!print_out)
+		return;
+
+	dev_info(emc->dev, "SDRAM[dev%u]: manufacturer: 0x%x (%s) rev1: 0x%x rev2: 0x%x prefetch: S%u density: %uMbit iowidth: %ubit\n",
+		 emem_dev, emc->manufacturer_id,
+		 lpddr2_jedec_manufacturer(emc->manufacturer_id),
+		 emc->revision_id1, emc->revision_id2,
+		 4 >> emc->basic_conf4.arch_type,
+		 64 << emc->basic_conf4.density,
+		 32 >> emc->basic_conf4.io_width);
+}
+
 static int emc_setup_hw(struct tegra_emc *emc)
 {
+	u32 emc_cfg, emc_dbg, emc_fbio, emc_adr_cfg;
 	u32 intmask = EMC_REFRESH_OVERFLOW_INT;
-	u32 emc_cfg, emc_dbg, emc_fbio;
+	static bool print_sdram_info_once;
+	enum emc_dram_type dram_type;
+	const char *dram_type_str;
+	unsigned int emem_numdev;
 
 	emc_cfg = readl_relaxed(emc->regs + EMC_CFG_2);
 
@@ -496,7 +638,36 @@
 	else
 		emc->dram_bus_width = 32;
 
-	dev_info_once(emc->dev, "%ubit DRAM bus\n", emc->dram_bus_width);
+	dram_type = FIELD_GET(EMC_FBIO_CFG5_DRAM_TYPE, emc_fbio);
+
+	switch (dram_type) {
+	case DRAM_TYPE_RESERVED:
+		dram_type_str = "INVALID";
+		break;
+	case DRAM_TYPE_DDR1:
+		dram_type_str = "DDR1";
+		break;
+	case DRAM_TYPE_LPDDR2:
+		dram_type_str = "LPDDR2";
+		break;
+	case DRAM_TYPE_DDR2:
+		dram_type_str = "DDR2";
+		break;
+	}
+
+	emc_adr_cfg = readl_relaxed(emc->regs + EMC_ADR_CFG_0);
+	emem_numdev = FIELD_GET(EMC_ADR_CFG_0_EMEM_NUMDEV, emc_adr_cfg) + 1;
+
+	dev_info_once(emc->dev, "%ubit DRAM bus, %u %s %s attached\n",
+		      emc->dram_bus_width, emem_numdev, dram_type_str,
+		      emem_numdev == 2 ? "devices" : "device");
+
+	if (dram_type == DRAM_TYPE_LPDDR2) {
+		while (emem_numdev--)
+			emc_read_lpddr_sdram_info(emc, emem_numdev,
+						  !print_sdram_info_once);
+		print_sdram_info_once = true;
+	}
 
 	return 0;
 }
@@ -1049,14 +1220,6 @@
 	emc->clk_nb.notifier_call = tegra_emc_clk_change_notify;
 	emc->dev = &pdev->dev;
 
-	np = tegra_emc_find_node_by_ram_code(&pdev->dev);
-	if (np) {
-		err = tegra_emc_load_timings_from_dt(emc, np);
-		of_node_put(np);
-		if (err)
-			return err;
-	}
-
 	emc->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(emc->regs))
 		return PTR_ERR(emc->regs);
@@ -1065,6 +1228,14 @@
 	if (err)
 		return err;
 
+	np = tegra_emc_find_node_by_ram_code(emc);
+	if (np) {
+		err = tegra_emc_load_timings_from_dt(emc, np);
+		of_node_put(np);
+		if (err)
+			return err;
+	}
+
 	err = devm_request_irq(&pdev->dev, irq, tegra_emc_isr, 0,
 			       dev_name(&pdev->dev), emc);
 	if (err) {
@@ -1117,4 +1288,5 @@
 
 MODULE_AUTHOR("Dmitry Osipenko <digetx@gmail.com>");
 MODULE_DESCRIPTION("NVIDIA Tegra20 EMC driver");
+MODULE_SOFTDEP("pre: governor_simpleondemand");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memstick/core/memstick.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memstick/core/memstick.c
@@ -410,6 +410,7 @@
 	return card;
 err_out:
 	host->card = old_card;
+	kfree_const(card->dev.kobj.name);
 	kfree(card);
 	return NULL;
 }
@@ -468,8 +469,10 @@
 				put_device(&card->dev);
 				host->card = NULL;
 			}
-		} else
+		} else {
+			kfree_const(card->dev.kobj.name);
 			kfree(card);
+		}
 	}
 
 out_power_off:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memstick/core/ms_block.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memstick/core/ms_block.c
@@ -1341,17 +1341,17 @@
 	msb->zone_count = msb->block_count / MS_BLOCKS_IN_ZONE;
 	msb->logical_block_count = msb->zone_count * 496 - 2;
 
-	msb->used_blocks_bitmap = kzalloc(msb->block_count / 8, GFP_KERNEL);
-	msb->erased_blocks_bitmap = kzalloc(msb->block_count / 8, GFP_KERNEL);
+	msb->used_blocks_bitmap = bitmap_zalloc(msb->block_count, GFP_KERNEL);
+	msb->erased_blocks_bitmap = bitmap_zalloc(msb->block_count, GFP_KERNEL);
 	msb->lba_to_pba_table =
 		kmalloc_array(msb->logical_block_count, sizeof(u16),
 			      GFP_KERNEL);
 
 	if (!msb->used_blocks_bitmap || !msb->lba_to_pba_table ||
 						!msb->erased_blocks_bitmap) {
-		kfree(msb->used_blocks_bitmap);
+		bitmap_free(msb->used_blocks_bitmap);
+		bitmap_free(msb->erased_blocks_bitmap);
 		kfree(msb->lba_to_pba_table);
-		kfree(msb->erased_blocks_bitmap);
 		return -ENOMEM;
 	}
 
@@ -1736,7 +1736,7 @@
 	msb->pages_in_block = boot_block->attr.block_size * 2;
 	msb->block_size = msb->page_size * msb->pages_in_block;
 
-	if (msb->page_size > PAGE_SIZE) {
+	if ((size_t)msb->page_size > PAGE_SIZE) {
 		/* this isn't supported by linux at all, anyway*/
 		dbg("device page %d size isn't supported", msb->page_size);
 		return -EINVAL;
@@ -1962,7 +1962,8 @@
 static void msb_data_clear(struct msb_data *msb)
 {
 	kfree(msb->boot_page);
-	kfree(msb->used_blocks_bitmap);
+	bitmap_free(msb->used_blocks_bitmap);
+	bitmap_free(msb->erased_blocks_bitmap);
 	kfree(msb->lba_to_pba_table);
 	kfree(msb->cache);
 	msb->card = NULL;
@@ -2149,6 +2150,11 @@
 
 	msb->usage_count = 1;
 	msb->io_queue = alloc_ordered_workqueue("ms_block", WQ_MEM_RECLAIM);
+	if (!msb->io_queue) {
+		rc = -ENOMEM;
+		goto out_cleanup_disk;
+	}
+
 	INIT_WORK(&msb->io_work, msb_io_work);
 	sg_init_table(msb->prealloc_sg, MS_BLOCK_MAX_SEGS+1);
 
@@ -2156,10 +2162,16 @@
 		set_disk_ro(msb->disk, 1);
 
 	msb_start(card);
-	device_add_disk(&card->dev, msb->disk, NULL);
+	rc = device_add_disk(&card->dev, msb->disk, NULL);
+	if (rc)
+		goto out_destroy_workqueue;
 	dbg("Disk added");
 	return 0;
 
+out_destroy_workqueue:
+	destroy_workqueue(msb->io_queue);
+out_cleanup_disk:
+	blk_cleanup_disk(msb->disk);
 out_free_tag_set:
 	blk_mq_free_tag_set(&msb->tag_set);
 out_release_id:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memstick/host/jmb38x_ms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memstick/host/jmb38x_ms.c
@@ -882,7 +882,7 @@
 
 	iounmap(host->addr);
 err_out_free:
-	kfree(msh);
+	memstick_free_host(msh);
 	return NULL;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memstick/host/r592.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memstick/host/r592.c
@@ -44,12 +44,10 @@
  * memstick_debug_get_tpc_name - debug helper that returns string for
  * a TPC number
  */
-const char *memstick_debug_get_tpc_name(int tpc)
+static __maybe_unused const char *memstick_debug_get_tpc_name(int tpc)
 {
 	return tpc_names[tpc-1];
 }
-EXPORT_SYMBOL(memstick_debug_get_tpc_name);
-
 
 /* Read a register*/
 static inline u32 r592_read_reg(struct r592_device *dev, int address)
@@ -829,7 +827,7 @@
 	/* Stop the processing thread.
 	That ensures that we won't take any more requests */
 	kthread_stop(dev->io_thread);
-
+	del_timer_sync(&dev->detect_timer);
 	r592_enable_device(dev, false);
 
 	while (!error && dev->req) {
@@ -838,15 +836,15 @@
 	}
 	memstick_remove_host(dev->host);
 
+	if (dev->dummy_dma_page)
+		dma_free_coherent(&pdev->dev, PAGE_SIZE, dev->dummy_dma_page,
+			dev->dummy_dma_page_physical_address);
+
 	free_irq(dev->irq, dev);
 	iounmap(dev->mmio);
 	pci_release_regions(pdev);
 	pci_disable_device(pdev);
 	memstick_free_host(dev->host);
-
-	if (dev->dummy_dma_page)
-		dma_free_coherent(&pdev->dev, PAGE_SIZE, dev->dummy_dma_page,
-			dev->dummy_dma_page_physical_address);
 }
 
 #ifdef CONFIG_PM_SLEEP
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/memstick/host/rtsx_usb_ms.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/memstick/host/rtsx_usb_ms.c
@@ -813,6 +813,7 @@
 
 	host->eject = true;
 	cancel_work_sync(&host->handle_req);
+	cancel_delayed_work_sync(&host->poll_card);
 
 	mutex_lock(&host->host_mutex);
 	if (host->req) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/message/fusion/mptlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/message/fusion/mptlan.c
@@ -1427,7 +1427,9 @@
 {
 	MPT_ADAPTER 		*ioc = pci_get_drvdata(pdev);
 	struct net_device	*dev = ioc->netdev;
+	struct mpt_lan_priv *priv = netdev_priv(dev);
 
+	cancel_delayed_work_sync(&priv->post_buckets_task);
 	if(dev != NULL) {
 		unregister_netdev(dev);
 		free_netdev(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/message/fusion/mptsas.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/message/fusion/mptsas.c
@@ -4232,10 +4232,8 @@
 static void
 mptsas_reprobe_lun(struct scsi_device *sdev, void *data)
 {
-	int rc;
-
 	sdev->no_uld_attach = data ? 1 : 0;
-	rc = scsi_device_reprobe(sdev);
+	WARN_ON(scsi_device_reprobe(sdev));
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/Kconfig
@@ -15,6 +15,7 @@
 	tristate "AMD CS5535 and CS5536 southbridge core functions"
 	select MFD_CORE
 	depends on PCI && (X86_32 || (X86 && COMPILE_TEST))
+	depends on !UML
 	help
 	  This is the core driver for CS5535/CS5536 MFD functions.  This is
 	  necessary for using the board's GPIO and MFGPT functionality.
@@ -1194,6 +1195,7 @@
 config MFD_SIMPLE_MFD_I2C
 	tristate
 	depends on I2C
+	select MFD_CORE
 	select REGMAP_I2C
 	help
 	  This driver creates a single register map with the intention for it
@@ -1375,6 +1377,7 @@
 
 config MFD_TI_AM335X_TSCADC
 	tristate "TI ADC / Touch Screen chip support"
+	depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
 	select MFD_CORE
 	select REGMAP
 	select REGMAP_MMIO
@@ -1994,6 +1997,7 @@
 	depends on I2C=y
 	depends on OF
 	select REGMAP_I2C
+	select REGMAP_IRQ
 	select MFD_CORE
 	help
 	  Select this option to get support for the ROHM BD9576MUF and
@@ -2130,6 +2134,18 @@
 	  under it in the device tree. Additional drivers must be enabled in
 	  order to use the functionality of the device.
 
+config MFD_AAEON
+	tristate "AAEON WMI MFD devices"
+	depends on ASUS_WMI
+	depends on UBUNTU_ODM_DRIVERS
+	help
+	  Say yes here to support mltiple IO devices on Single Board Computers
+	  produced by AAEON.
+
+	  This driver leverages the ASUS WMI interface to access device
+	  resources.
+
+
 menu "Multimedia Capabilities Port drivers"
 	depends on ARCH_SA1100
 
@@ -2227,5 +2243,15 @@
 	  Additional drivers must be enabled in order to use the functionality
 	  of the device.
 
+config MFD_LJCA
+	tristate "Intel La Jolla Cove Adapter support"
+	select MFD_CORE
+	depends on USB
+	help
+	  This adds support for Intel La Jolla Cove USB-I2C/SPI/GPIO
+	  Adapter (LJCA). Additional drivers such as I2C_LJCA,
+	  GPIO_LJCA, etc. must be enabled in order to use the
+	  functionality of the device.
+
 endmenu
 endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/Makefile
@@ -273,8 +273,9 @@
 
 obj-$(CONFIG_MFD_ATC260X)	+= atc260x-core.o
 obj-$(CONFIG_MFD_ATC260X_I2C)	+= atc260x-i2c.o
+obj-$(CONFIG_MFD_AAEON)		+= mfd-aaeon.o
 
-rsmu-i2c-objs			:= rsmu_core.o rsmu_i2c.o
-rsmu-spi-objs			:= rsmu_core.o rsmu_spi.o
-obj-$(CONFIG_MFD_RSMU_I2C)	+= rsmu-i2c.o
-obj-$(CONFIG_MFD_RSMU_SPI)	+= rsmu-spi.o
+obj-$(CONFIG_MFD_RSMU_I2C)	+= rsmu_i2c.o rsmu_core.o
+obj-$(CONFIG_MFD_RSMU_SPI)	+= rsmu_spi.o rsmu_core.o
+
+obj-$(CONFIG_MFD_LJCA)		+= ljca.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/altera-sysmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/altera-sysmgr.c
@@ -110,7 +110,9 @@
 
 	dev = driver_find_device_by_of_node(&altr_sysmgr_driver.driver,
 					    (void *)sysmgr_np);
-	of_node_put(sysmgr_np);
+	if (property)
+		of_node_put(sysmgr_np);
+
 	if (!dev)
 		return ERR_PTR(-EPROBE_DEFER);
 
@@ -153,7 +155,7 @@
 		if (!base)
 			return -ENOMEM;
 
-		sysmgr_config.max_register = resource_size(res) - 3;
+		sysmgr_config.max_register = resource_size(res) - 4;
 		regmap = devm_regmap_init_mmio(dev, base, &sysmgr_config);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/arizona-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/arizona-core.c
@@ -45,7 +45,7 @@
 	if (arizona->clk32k_ref == 1) {
 		switch (arizona->pdata.clk32k_src) {
 		case ARIZONA_32KZ_MCLK1:
-			ret = pm_runtime_get_sync(arizona->dev);
+			ret = pm_runtime_resume_and_get(arizona->dev);
 			if (ret != 0)
 				goto err_ref;
 			ret = clk_prepare_enable(arizona->mclk[ARIZONA_MCLK1]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/arizona-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/arizona-spi.c
@@ -118,6 +118,9 @@
 	arizona->pdata.micd_ranges = arizona_micd_aosp_ranges;
 	arizona->pdata.num_micd_ranges = ARRAY_SIZE(arizona_micd_aosp_ranges);
 
+	/* Use left headphone speaker for HP vs line-out detection */
+	arizona->pdata.hpdet_channel = ARIZONA_ACCDET_MODE_HPL;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/asic3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/asic3.c
@@ -906,14 +906,14 @@
 		ret = mfd_add_devices(&pdev->dev, pdev->id,
 			&asic3_cell_ds1wm, 1, mem, asic->irq_base, NULL);
 		if (ret < 0)
-			goto out;
+			goto out_unmap;
 	}
 
 	if (mem_sdio && (irq >= 0)) {
 		ret = mfd_add_devices(&pdev->dev, pdev->id,
 			&asic3_cell_mmc, 1, mem_sdio, irq, NULL);
 		if (ret < 0)
-			goto out;
+			goto out_unmap;
 	}
 
 	ret = 0;
@@ -927,8 +927,12 @@
 		ret = mfd_add_devices(&pdev->dev, 0,
 			asic3_cell_leds, ASIC3_NUM_LEDS, NULL, 0, NULL);
 	}
+	return ret;
 
- out:
+out_unmap:
+	if (asic->tmio_cnf)
+		iounmap(asic->tmio_cnf);
+out:
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/atmel-flexcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/atmel-flexcom.c
@@ -87,8 +87,7 @@
 };
 MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
 
-#ifdef CONFIG_PM_SLEEP
-static int atmel_flexcom_resume(struct device *dev)
+static int __maybe_unused atmel_flexcom_resume_noirq(struct device *dev)
 {
 	struct atmel_flexcom *ddata = dev_get_drvdata(dev);
 	int err;
@@ -105,16 +104,16 @@
 
 	return 0;
 }
-#endif
 
-static SIMPLE_DEV_PM_OPS(atmel_flexcom_pm_ops, NULL,
-			 atmel_flexcom_resume);
+static const struct dev_pm_ops atmel_flexcom_pm_ops = {
+	.resume_noirq = atmel_flexcom_resume_noirq,
+};
 
 static struct platform_driver atmel_flexcom_driver = {
 	.probe	= atmel_flexcom_probe,
 	.driver	= {
 		.name		= "atmel_flexcom",
-		.pm		= &atmel_flexcom_pm_ops,
+		.pm		= pm_ptr(&atmel_flexcom_pm_ops),
 		.of_match_table	= atmel_flexcom_of_match,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/da9052-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/da9052-spi.c
@@ -37,7 +37,7 @@
 	spi_set_drvdata(spi, da9052);
 
 	config = da9052_regmap_config;
-	config.read_flag_mask = 1;
+	config.write_flag_mask = 1;
 	config.reg_bits = 7;
 	config.pad_bits = 1;
 	config.val_bits = 8;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/davinci_voicecodec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/davinci_voicecodec.c
@@ -46,14 +46,12 @@
 	}
 	clk_enable(davinci_vc->clk);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
-	fifo_base = (dma_addr_t)res->start;
-	davinci_vc->base = devm_ioremap_resource(&pdev->dev, res);
+	davinci_vc->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 	if (IS_ERR(davinci_vc->base)) {
 		ret = PTR_ERR(davinci_vc->base);
 		goto fail;
 	}
+	fifo_base = (dma_addr_t)res->start;
 
 	davinci_vc->regmap = devm_regmap_init_mmio(&pdev->dev,
 						   davinci_vc->base,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/dln2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/dln2.c
@@ -50,6 +50,7 @@
 	DLN2_HANDLE_GPIO,
 	DLN2_HANDLE_I2C,
 	DLN2_HANDLE_SPI,
+	DLN2_HANDLE_ADC,
 	DLN2_HANDLES
 };
 
@@ -653,6 +654,7 @@
 	DLN2_ACPI_MATCH_GPIO	= 0,
 	DLN2_ACPI_MATCH_I2C	= 1,
 	DLN2_ACPI_MATCH_SPI	= 2,
+	DLN2_ACPI_MATCH_ADC	= 3,
 };
 
 static struct dln2_platform_data dln2_pdata_gpio = {
@@ -683,6 +685,16 @@
 	.adr = DLN2_ACPI_MATCH_SPI,
 };
 
+/* Only one ADC port supported */
+static struct dln2_platform_data dln2_pdata_adc = {
+	.handle = DLN2_HANDLE_ADC,
+	.port = 0,
+};
+
+static struct mfd_cell_acpi_match dln2_acpi_match_adc = {
+	.adr = DLN2_ACPI_MATCH_ADC,
+};
+
 static const struct mfd_cell dln2_devs[] = {
 	{
 		.name = "dln2-gpio",
@@ -702,6 +714,12 @@
 		.platform_data = &dln2_pdata_spi,
 		.pdata_size = sizeof(struct dln2_platform_data),
 	},
+	{
+		.name = "dln2-adc",
+		.acpi_match = &dln2_acpi_match_adc,
+		.platform_data = &dln2_pdata_adc,
+		.pdata_size = sizeof(struct dln2_platform_data),
+	},
 };
 
 static void dln2_stop(struct dln2_dev *dln2)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/fsl-imx25-tsadc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/fsl-imx25-tsadc.c
@@ -69,7 +69,7 @@
 	int irq;
 
 	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0)
+	if (irq < 0)
 		return irq;
 
 	tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
@@ -84,6 +84,19 @@
 	return 0;
 }
 
+static int mx25_tsadc_unset_irq(struct platform_device *pdev)
+{
+	struct mx25_tsadc *tsadc = platform_get_drvdata(pdev);
+	int irq = platform_get_irq(pdev, 0);
+
+	if (irq >= 0) {
+		irq_set_chained_handler_and_data(irq, NULL, NULL);
+		irq_domain_remove(tsadc->domain);
+	}
+
+	return 0;
+}
+
 static void mx25_tsadc_setup_clk(struct platform_device *pdev,
 				 struct mx25_tsadc *tsadc)
 {
@@ -171,18 +184,21 @@
 
 	platform_set_drvdata(pdev, tsadc);
 
-	return devm_of_platform_populate(dev);
+	ret = devm_of_platform_populate(dev);
+	if (ret)
+		goto err_irq;
+
+	return 0;
+
+err_irq:
+	mx25_tsadc_unset_irq(pdev);
+
+	return ret;
 }
 
 static int mx25_tsadc_remove(struct platform_device *pdev)
 {
-	struct mx25_tsadc *tsadc = platform_get_drvdata(pdev);
-	int irq = platform_get_irq(pdev, 0);
-
-	if (irq) {
-		irq_set_chained_handler_and_data(irq, NULL, NULL);
-		irq_domain_remove(tsadc->domain);
-	}
+	mx25_tsadc_unset_irq(pdev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/intel-lpss-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/intel-lpss-acpi.c
@@ -136,6 +136,7 @@
 {
 	struct intel_lpss_platform_info *info;
 	const struct acpi_device_id *id;
+	int ret;
 
 	id = acpi_match_device(intel_lpss_acpi_ids, &pdev->dev);
 	if (!id)
@@ -147,12 +148,19 @@
 		return -ENOMEM;
 
 	info->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!info->mem)
+		return -ENODEV;
+
 	info->irq = platform_get_irq(pdev, 0);
 
+	ret = intel_lpss_probe(&pdev->dev, info);
+	if (ret)
+		return ret;
+
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
-	return intel_lpss_probe(&pdev->dev, info);
+	return 0;
 }
 
 static int intel_lpss_acpi_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/intel-lpss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/intel-lpss.c
@@ -301,8 +301,8 @@
 
 	snprintf(name, sizeof(name), "%s-div", devname);
 	tmp = clk_register_fractional_divider(NULL, name, __clk_get_name(tmp),
+					      0, lpss->priv, 1, 15, 16, 15,
 					      CLK_FRAC_DIVIDER_POWER_OF_TWO_PS,
-					      lpss->priv, 1, 15, 16, 15, 0,
 					      NULL);
 	if (IS_ERR(tmp))
 		return PTR_ERR(tmp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/intel_soc_pmic_bxtwc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/intel_soc_pmic_bxtwc.c
@@ -231,43 +231,54 @@
 
 static struct mfd_cell bxt_wc_dev[] = {
 	{
-		.name = "bxt_wcove_gpadc",
-		.num_resources = ARRAY_SIZE(adc_resources),
-		.resources = adc_resources,
-	},
-	{
 		.name = "bxt_wcove_thermal",
 		.num_resources = ARRAY_SIZE(thermal_resources),
 		.resources = thermal_resources,
 	},
 	{
-		.name = "bxt_wcove_usbc",
-		.num_resources = ARRAY_SIZE(usbc_resources),
-		.resources = usbc_resources,
+		.name = "bxt_wcove_gpio",
+		.num_resources = ARRAY_SIZE(gpio_resources),
+		.resources = gpio_resources,
 	},
 	{
-		.name = "bxt_wcove_ext_charger",
-		.num_resources = ARRAY_SIZE(charger_resources),
-		.resources = charger_resources,
+		.name = "bxt_wcove_region",
 	},
+};
+
+static const struct mfd_cell bxt_wc_tmu_dev[] = {
+	{
+		.name = "bxt_wcove_tmu",
+		.num_resources = ARRAY_SIZE(tmu_resources),
+		.resources = tmu_resources,
+	},
+};
+
+static const struct mfd_cell bxt_wc_bcu_dev[] = {
 	{
 		.name = "bxt_wcove_bcu",
 		.num_resources = ARRAY_SIZE(bcu_resources),
 		.resources = bcu_resources,
 	},
+};
+
+static const struct mfd_cell bxt_wc_adc_dev[] = {
 	{
-		.name = "bxt_wcove_tmu",
-		.num_resources = ARRAY_SIZE(tmu_resources),
-		.resources = tmu_resources,
+		.name = "bxt_wcove_gpadc",
+		.num_resources = ARRAY_SIZE(adc_resources),
+		.resources = adc_resources,
 	},
+};
 
+static struct mfd_cell bxt_wc_chgr_dev[] = {
 	{
-		.name = "bxt_wcove_gpio",
-		.num_resources = ARRAY_SIZE(gpio_resources),
-		.resources = gpio_resources,
+		.name = "bxt_wcove_usbc",
+		.num_resources = ARRAY_SIZE(usbc_resources),
+		.resources = usbc_resources,
 	},
 	{
-		.name = "bxt_wcove_region",
+		.name = "bxt_wcove_ext_charger",
+		.num_resources = ARRAY_SIZE(charger_resources),
+		.resources = charger_resources,
 	},
 };
 
@@ -410,19 +421,37 @@
 	int irq;
 
 	irq = regmap_irq_get_virq(pdata, pirq);
-	if (irq < 0) {
-		dev_err(pmic->dev,
-			"Failed to get parent vIRQ(%d) for chip %s, ret:%d\n",
-			pirq, chip->name, irq);
-		return irq;
-	}
+	if (irq < 0)
+		return dev_err_probe(pmic->dev, irq, "Failed to get parent vIRQ(%d) for chip %s\n",
+				     pirq, chip->name);
 
 	return devm_regmap_add_irq_chip(pmic->dev, pmic->regmap, irq, irq_flags,
 					0, chip, data);
 }
 
+static int bxtwc_add_chained_devices(struct intel_soc_pmic *pmic,
+				     const struct mfd_cell *cells, int n_devs,
+				     struct regmap_irq_chip_data *pdata,
+				     int pirq, int irq_flags,
+				     const struct regmap_irq_chip *chip,
+				     struct regmap_irq_chip_data **data)
+{
+	struct device *dev = pmic->dev;
+	struct irq_domain *domain;
+	int ret;
+
+	ret = bxtwc_add_chained_irq_chip(pmic, pdata, pirq, irq_flags, chip, data);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to add %s IRQ chip\n", chip->name);
+
+	domain = regmap_irq_get_domain(*data);
+
+	return devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE, cells, n_devs, NULL, 0, domain);
+}
+
 static int bxtwc_probe(struct platform_device *pdev)
 {
+	struct device *dev = &pdev->dev;
 	int ret;
 	acpi_handle handle;
 	acpi_status status;
@@ -431,15 +460,10 @@
 
 	handle = ACPI_HANDLE(&pdev->dev);
 	status = acpi_evaluate_integer(handle, "_HRV", NULL, &hrv);
-	if (ACPI_FAILURE(status)) {
-		dev_err(&pdev->dev, "Failed to get PMIC hardware revision\n");
-		return -ENODEV;
-	}
-	if (hrv != BROXTON_PMIC_WC_HRV) {
-		dev_err(&pdev->dev, "Invalid PMIC hardware revision: %llu\n",
-			hrv);
-		return -ENODEV;
-	}
+	if (ACPI_FAILURE(status))
+		return dev_err_probe(dev, -ENODEV, "Failed to get PMIC hardware revision\n");
+	if (hrv != BROXTON_PMIC_WC_HRV)
+		return dev_err_probe(dev, -ENODEV, "Invalid PMIC hardware revision: %llu\n", hrv);
 
 	pmic = devm_kzalloc(&pdev->dev, sizeof(*pmic), GFP_KERNEL);
 	if (!pmic)
@@ -459,79 +483,59 @@
 
 	pmic->regmap = devm_regmap_init(&pdev->dev, NULL, pmic,
 					&bxtwc_regmap_config);
-	if (IS_ERR(pmic->regmap)) {
-		ret = PTR_ERR(pmic->regmap);
-		dev_err(&pdev->dev, "Failed to initialise regmap: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(pmic->regmap))
+		return dev_err_probe(dev, PTR_ERR(pmic->regmap), "Failed to initialise regmap\n");
 
 	ret = devm_regmap_add_irq_chip(&pdev->dev, pmic->regmap, pmic->irq,
 				       IRQF_ONESHOT | IRQF_SHARED,
 				       0, &bxtwc_regmap_irq_chip,
 				       &pmic->irq_chip_data);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add IRQ chip\n");
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to add IRQ chip\n");
+
+	ret = bxtwc_add_chained_devices(pmic, bxt_wc_tmu_dev, ARRAY_SIZE(bxt_wc_tmu_dev),
+					pmic->irq_chip_data,
+					BXTWC_TMU_LVL1_IRQ,
+					IRQF_ONESHOT,
+					&bxtwc_regmap_irq_chip_tmu,
+					&pmic->irq_chip_data_tmu);
+	if (ret)
 		return ret;
-	}
 
 	ret = bxtwc_add_chained_irq_chip(pmic, pmic->irq_chip_data,
 					 BXTWC_PWRBTN_LVL1_IRQ,
 					 IRQF_ONESHOT,
 					 &bxtwc_regmap_irq_chip_pwrbtn,
 					 &pmic->irq_chip_data_pwrbtn);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add PWRBTN IRQ chip\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to add PWRBTN IRQ chip\n");
 
-	ret = bxtwc_add_chained_irq_chip(pmic, pmic->irq_chip_data,
-					 BXTWC_TMU_LVL1_IRQ,
-					 IRQF_ONESHOT,
-					 &bxtwc_regmap_irq_chip_tmu,
-					 &pmic->irq_chip_data_tmu);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add TMU IRQ chip\n");
+	ret = bxtwc_add_chained_devices(pmic, bxt_wc_bcu_dev, ARRAY_SIZE(bxt_wc_bcu_dev),
+					pmic->irq_chip_data,
+					BXTWC_BCU_LVL1_IRQ,
+					IRQF_ONESHOT,
+					&bxtwc_regmap_irq_chip_bcu,
+					&pmic->irq_chip_data_bcu);
+	if (ret)
 		return ret;
-	}
 
-	/* Add chained IRQ handler for BCU IRQs */
-	ret = bxtwc_add_chained_irq_chip(pmic, pmic->irq_chip_data,
-					 BXTWC_BCU_LVL1_IRQ,
-					 IRQF_ONESHOT,
-					 &bxtwc_regmap_irq_chip_bcu,
-					 &pmic->irq_chip_data_bcu);
-
-
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add BUC IRQ chip\n");
-		return ret;
-	}
-
-	/* Add chained IRQ handler for ADC IRQs */
-	ret = bxtwc_add_chained_irq_chip(pmic, pmic->irq_chip_data,
-					 BXTWC_ADC_LVL1_IRQ,
-					 IRQF_ONESHOT,
-					 &bxtwc_regmap_irq_chip_adc,
-					 &pmic->irq_chip_data_adc);
-
-
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add ADC IRQ chip\n");
+	ret = bxtwc_add_chained_devices(pmic, bxt_wc_adc_dev, ARRAY_SIZE(bxt_wc_adc_dev),
+					pmic->irq_chip_data,
+					BXTWC_ADC_LVL1_IRQ,
+					IRQF_ONESHOT,
+					&bxtwc_regmap_irq_chip_adc,
+					&pmic->irq_chip_data_adc);
+	if (ret)
 		return ret;
-	}
-
-	/* Add chained IRQ handler for CHGR IRQs */
-	ret = bxtwc_add_chained_irq_chip(pmic, pmic->irq_chip_data,
-					 BXTWC_CHGR_LVL1_IRQ,
-					 IRQF_ONESHOT,
-					 &bxtwc_regmap_irq_chip_chgr,
-					 &pmic->irq_chip_data_chgr);
-
 
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add CHGR IRQ chip\n");
+	ret = bxtwc_add_chained_devices(pmic, bxt_wc_chgr_dev, ARRAY_SIZE(bxt_wc_chgr_dev),
+					pmic->irq_chip_data,
+					BXTWC_CHGR_LVL1_IRQ,
+					IRQF_ONESHOT,
+					&bxtwc_regmap_irq_chip_chgr,
+					&pmic->irq_chip_data_chgr);
+	if (ret)
 		return ret;
-	}
 
 	/* Add chained IRQ handler for CRIT IRQs */
 	ret = bxtwc_add_chained_irq_chip(pmic, pmic->irq_chip_data,
@@ -539,19 +543,13 @@
 					 IRQF_ONESHOT,
 					 &bxtwc_regmap_irq_chip_crit,
 					 &pmic->irq_chip_data_crit);
-
-
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add CRIT IRQ chip\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to add CRIT IRQ chip\n");
 
 	ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE, bxt_wc_dev,
 				   ARRAY_SIZE(bxt_wc_dev), NULL, 0, NULL);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to add devices\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to add devices\n");
 
 	ret = sysfs_create_group(&pdev->dev.kobj, &bxtwc_group);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/intel_soc_pmic_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/intel_soc_pmic_core.c
@@ -95,6 +95,7 @@
 	return 0;
 
 err_del_irq_chip:
+	pwm_remove_table(crc_pwm_lookup, ARRAY_SIZE(crc_pwm_lookup));
 	regmap_del_irq_chip(pmic->irq, pmic->irq_chip_data);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/ipaq-micro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/ipaq-micro.c
@@ -403,7 +403,7 @@
 	micro_reset_comm(micro);
 
 	irq = platform_get_irq(pdev, 0);
-	if (!irq)
+	if (irq < 0)
 		return -EINVAL;
 	ret = devm_request_irq(&pdev->dev, irq, micro_serial_isr,
 			       IRQF_SHARED, "ipaq-micro",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/ljca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/ljca.c
@@ -0,0 +1,1187 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Intel La Jolla Cove Adapter USB driver
+ *
+ * Copyright (c) 2021, Intel Corporation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/ljca.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+#include <linux/usb.h>
+
+enum ljca_acpi_match_adr {
+	LJCA_ACPI_MATCH_GPIO,
+	LJCA_ACPI_MATCH_I2C1,
+	LJCA_ACPI_MATCH_I2C2,
+	LJCA_ACPI_MATCH_SPI1,
+};
+
+static char *gpio_hids[] = {
+	"INTC1074",
+	"INTC1096",
+};
+static struct mfd_cell_acpi_match ljca_acpi_match_gpio;
+
+static char *i2c_hids[] = {
+	"INTC1075",
+	"INTC1097",
+};
+static struct mfd_cell_acpi_match ljca_acpi_match_i2cs[2];
+
+static char *spi_hids[] = {
+	"INTC1091",
+	"INTC1098",
+};
+static struct mfd_cell_acpi_match ljca_acpi_match_spis[1];
+
+struct ljca_msg {
+	u8 type;
+	u8 cmd;
+	u8 flags;
+	u8 len;
+	u8 data[];
+} __packed;
+
+struct fw_version {
+	u8 major;
+	u8 minor;
+	u16 patch;
+	u16 build;
+} __packed;
+
+/* stub types */
+enum stub_type {
+	MNG_STUB = 1,
+	DIAG_STUB,
+	GPIO_STUB,
+	I2C_STUB,
+	SPI_STUB,
+};
+
+/* command Flags */
+#define ACK_FLAG BIT(0)
+#define RESP_FLAG BIT(1)
+#define CMPL_FLAG BIT(2)
+
+/* MNG stub commands */
+enum ljca_mng_cmd {
+	MNG_GET_VERSION = 1,
+	MNG_RESET_NOTIFY,
+	MNG_RESET,
+	MNG_ENUM_GPIO,
+	MNG_ENUM_I2C,
+	MNG_POWER_STATE_CHANGE,
+	MNG_SET_DFU_MODE,
+	MNG_ENUM_SPI,
+};
+
+/* DIAG commands */
+enum diag_cmd {
+	DIAG_GET_STATE = 1,
+	DIAG_GET_STATISTIC,
+	DIAG_SET_TRACE_LEVEL,
+	DIAG_SET_ECHO_MODE,
+	DIAG_GET_FW_LOG,
+	DIAG_GET_FW_COREDUMP,
+	DIAG_TRIGGER_WDT,
+	DIAG_TRIGGER_FAULT,
+	DIAG_FEED_WDT,
+	DIAG_GET_SECURE_STATE,
+};
+
+struct ljca_i2c_ctr_info {
+	u8 id;
+	u8 capacity;
+	u8 intr_pin;
+} __packed;
+
+struct ljca_i2c_descriptor {
+	u8 num;
+	struct ljca_i2c_ctr_info info[];
+} __packed;
+
+struct ljca_spi_ctr_info {
+	u8 id;
+	u8 capacity;
+} __packed;
+
+struct ljca_spi_descriptor {
+	u8 num;
+	struct ljca_spi_ctr_info info[];
+} __packed;
+
+struct ljca_bank_descriptor {
+	u8 bank_id;
+	u8 pin_num;
+
+	/* 1 bit for each gpio, 1 means valid */
+	u32 valid_pins;
+} __packed;
+
+struct ljca_gpio_descriptor {
+	u8 pins_per_bank;
+	u8 bank_num;
+	struct ljca_bank_descriptor bank_desc[];
+} __packed;
+
+#define MAX_PACKET_SIZE 64
+#define MAX_PAYLOAD_SIZE (MAX_PACKET_SIZE - sizeof(struct ljca_msg))
+#define USB_WRITE_TIMEOUT 200
+#define USB_WRITE_ACK_TIMEOUT 500
+#define USB_ENUM_STUB_TIMEOUT 20
+
+struct ljca_event_cb_entry {
+	struct platform_device *pdev;
+	ljca_event_cb_t notify;
+};
+
+struct ljca_stub_packet {
+	u8 *ibuf;
+	u32 ibuf_len;
+};
+
+struct ljca_stub {
+	struct list_head list;
+	u8 type;
+	struct usb_interface *intf;
+	spinlock_t event_cb_lock;
+
+	struct ljca_stub_packet ipacket;
+
+	/* for identify ack */
+	bool acked;
+	int cur_cmd;
+
+	struct ljca_event_cb_entry event_entry;
+};
+
+static inline void *ljca_priv(const struct ljca_stub *stub)
+{
+	return (char *)stub + sizeof(struct ljca_stub);
+}
+
+enum ljca_state {
+	LJCA_STOPPED,
+	LJCA_INITED,
+	LJCA_RESET_HANDSHAKE,
+	LJCA_RESET_SYNCED,
+	LJCA_ENUM_GPIO_COMPLETE,
+	LJCA_ENUM_I2C_COMPLETE,
+	LJCA_ENUM_SPI_COMPLETE,
+	LJCA_SUSPEND,
+	LJCA_STARTED,
+	LJCA_FAILED,
+};
+
+struct ljca_dev {
+	struct usb_device *udev;
+	struct usb_interface *intf;
+	u8 in_ep; /* the address of the bulk in endpoint */
+	u8 out_ep; /* the address of the bulk out endpoint */
+
+	/* the urb/buffer for read */
+	struct urb *in_urb;
+	unsigned char *ibuf;
+	size_t ibuf_len;
+
+	int state;
+
+	struct list_head stubs_list;
+
+	/* to wait for an ongoing write ack */
+	wait_queue_head_t ack_wq;
+
+	struct mfd_cell *cells;
+	int cell_count;
+	struct mutex mutex;
+};
+
+static int try_match_acpi_hid(struct acpi_device *child,
+			      struct mfd_cell_acpi_match *match, char **hids,
+			      int hids_num)
+{
+	struct acpi_device_id ids[2] = {};
+	int i;
+
+	for (i = 0; i < hids_num; i++) {
+		strlcpy(ids[0].id, hids[i], sizeof(ids[0].id));
+		if (!acpi_match_device_ids(child, ids)) {
+			match->pnpid = hids[i];
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int precheck_acpi_hid(struct usb_interface *intf)
+{
+	struct acpi_device *parent, *child;
+
+	parent = ACPI_COMPANION(&intf->dev);
+	if (!parent)
+		return -ENODEV;
+
+	list_for_each_entry (child, &parent->children, node) {
+		try_match_acpi_hid(child, &ljca_acpi_match_gpio, gpio_hids,
+				   ARRAY_SIZE(gpio_hids));
+		try_match_acpi_hid(child, &ljca_acpi_match_i2cs[0], i2c_hids,
+				   ARRAY_SIZE(i2c_hids));
+		try_match_acpi_hid(child, &ljca_acpi_match_i2cs[1], i2c_hids,
+				   ARRAY_SIZE(i2c_hids));
+		try_match_acpi_hid(child, &ljca_acpi_match_spis[0], spi_hids,
+				   ARRAY_SIZE(spi_hids));
+	}
+
+	return 0;
+}
+
+static bool ljca_validate(void *data, u32 data_len)
+{
+	struct ljca_msg *header = (struct ljca_msg *)data;
+
+	return (header->len + sizeof(*header) == data_len);
+}
+
+void ljca_dump(struct ljca_dev *ljca, void *buf, int len)
+{
+	int i;
+	u8 tmp[256] = { 0 };
+	int n = 0;
+
+	if (!len)
+		return;
+
+	for (i = 0; i < len; i++)
+		n += scnprintf(tmp + n, sizeof(tmp) - n - 1, "%02x ",
+			       ((u8 *)buf)[i]);
+
+	dev_dbg(&ljca->intf->dev, "%s\n", tmp);
+}
+
+static struct ljca_stub *ljca_stub_alloc(struct ljca_dev *ljca, int priv_size)
+{
+	struct ljca_stub *stub;
+
+	stub = kzalloc(sizeof(*stub) + priv_size, GFP_KERNEL);
+	if (!stub)
+		return ERR_PTR(-ENOMEM);
+
+	spin_lock_init(&stub->event_cb_lock);
+	INIT_LIST_HEAD(&stub->list);
+	list_add_tail(&stub->list, &ljca->stubs_list);
+	dev_dbg(&ljca->intf->dev, "enuming a stub success\n");
+	return stub;
+}
+
+static struct ljca_stub *ljca_stub_find(struct ljca_dev *ljca, u8 type)
+{
+	struct ljca_stub *stub;
+
+	list_for_each_entry (stub, &ljca->stubs_list, list) {
+		if (stub->type == type)
+			return stub;
+	}
+
+	dev_err(&ljca->intf->dev, "usb stub not find, type: %d", type);
+	return ERR_PTR(-ENODEV);
+}
+
+static void ljca_stub_notify(struct ljca_stub *stub, u8 cmd,
+			     const void *evt_data, int len)
+{
+	unsigned long flags;
+	spin_lock_irqsave(&stub->event_cb_lock, flags);
+	if (stub->event_entry.notify && stub->event_entry.pdev)
+		stub->event_entry.notify(stub->event_entry.pdev, cmd, evt_data,
+					 len);
+	spin_unlock_irqrestore(&stub->event_cb_lock, flags);
+}
+
+static int ljca_parse(struct ljca_dev *ljca, struct ljca_msg *header)
+{
+	struct ljca_stub *stub;
+
+	stub = ljca_stub_find(ljca, header->type);
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	if (!(header->flags & ACK_FLAG)) {
+		ljca_stub_notify(stub, header->cmd, header->data, header->len);
+		return 0;
+	}
+
+	if (stub->cur_cmd != header->cmd) {
+		dev_err(&ljca->intf->dev, "header->cmd:%x != stub->cur_cmd:%x",
+			header->cmd, stub->cur_cmd);
+		return -EINVAL;
+	}
+
+	stub->ipacket.ibuf_len = header->len;
+	if (stub->ipacket.ibuf)
+		memcpy(stub->ipacket.ibuf, header->data, header->len);
+
+	stub->acked = true;
+	wake_up(&ljca->ack_wq);
+
+	return 0;
+}
+
+static int ljca_stub_write(struct ljca_stub *stub, u8 cmd, const void *obuf,
+			   int obuf_len, void *ibuf, int *ibuf_len,
+			   bool wait_ack, int timeout)
+{
+	struct ljca_msg *header;
+	struct ljca_dev *ljca = usb_get_intfdata(stub->intf);
+	int ret;
+	u8 flags = CMPL_FLAG;
+	int actual;
+
+	if (ljca->state == LJCA_STOPPED)
+		return -ENODEV;
+
+	if (obuf_len > MAX_PAYLOAD_SIZE)
+		return -EINVAL;
+
+	if (wait_ack)
+		flags |= ACK_FLAG;
+
+	stub->ipacket.ibuf_len = 0;
+	header = kmalloc(sizeof(*header) + obuf_len, GFP_KERNEL);
+	if (!header)
+		return -ENOMEM;
+
+	header->type = stub->type;
+	header->cmd = cmd;
+	header->flags = flags;
+	header->len = obuf_len;
+
+	memcpy(header->data, obuf, obuf_len);
+	dev_dbg(&ljca->intf->dev, "send: type:%d cmd:%d flags:%d len:%d\n",
+		header->type, header->cmd, header->flags, header->len);
+	ljca_dump(ljca, header->data, header->len);
+
+	mutex_lock(&ljca->mutex);
+	stub->cur_cmd = cmd;
+	stub->ipacket.ibuf = ibuf;
+	stub->acked = false;
+	usb_autopm_get_interface(ljca->intf);
+	ret = usb_bulk_msg(ljca->udev,
+			   usb_sndbulkpipe(ljca->udev, ljca->out_ep), header,
+			   sizeof(struct ljca_msg) + obuf_len, &actual,
+			   USB_WRITE_TIMEOUT);
+	kfree(header);
+	if (ret || actual != sizeof(struct ljca_msg) + obuf_len) {
+		dev_err(&ljca->intf->dev,
+			"bridge write failed ret:%d total_len:%d\n ", ret,
+			actual);
+		goto error;
+	}
+
+	if (wait_ack) {
+		ret = wait_event_timeout(ljca->ack_wq, stub->acked,
+					 msecs_to_jiffies(timeout));
+		if (!ret || !stub->acked) {
+			dev_err(&ljca->intf->dev,
+				"acked sem wait timed out ret:%d timeout:%d ack:%d\n",
+				ret, timeout, stub->acked);
+			ret = -ETIMEDOUT;
+			goto error;
+		}
+	}
+
+	if (ibuf_len)
+		*ibuf_len = stub->ipacket.ibuf_len;
+
+	stub->ipacket.ibuf = NULL;
+	stub->ipacket.ibuf_len = 0;
+	ret = 0;
+error:
+	usb_autopm_put_interface(ljca->intf);
+	mutex_unlock(&ljca->mutex);
+	return ret;
+}
+
+static int ljca_transfer_internal(struct platform_device *pdev, u8 cmd,
+				  const void *obuf, int obuf_len, void *ibuf,
+				  int *ibuf_len, bool wait_ack)
+{
+	struct ljca_platform_data *ljca_pdata;
+	struct ljca_dev *ljca;
+	struct ljca_stub *stub;
+
+	if (!pdev)
+		return -EINVAL;
+
+	ljca = dev_get_drvdata(pdev->dev.parent);
+	ljca_pdata = dev_get_platdata(&pdev->dev);
+	stub = ljca_stub_find(ljca, ljca_pdata->type);
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	return ljca_stub_write(stub, cmd, obuf, obuf_len, ibuf, ibuf_len,
+			       wait_ack, USB_WRITE_ACK_TIMEOUT);
+}
+
+int ljca_transfer(struct platform_device *pdev, u8 cmd, const void *obuf,
+		  int obuf_len, void *ibuf, int *ibuf_len)
+{
+	return ljca_transfer_internal(pdev, cmd, obuf, obuf_len, ibuf, ibuf_len,
+				      true);
+}
+EXPORT_SYMBOL_GPL(ljca_transfer);
+
+int ljca_transfer_noack(struct platform_device *pdev, u8 cmd, const void *obuf,
+			int obuf_len)
+{
+	return ljca_transfer_internal(pdev, cmd, obuf, obuf_len, NULL, NULL,
+				      false);
+}
+EXPORT_SYMBOL_GPL(ljca_transfer_noack);
+
+int ljca_register_event_cb(struct platform_device *pdev,
+			   ljca_event_cb_t event_cb)
+{
+	struct ljca_platform_data *ljca_pdata;
+	struct ljca_dev *ljca;
+	struct ljca_stub *stub;
+	unsigned long flags;
+
+	if (!pdev)
+		return -EINVAL;
+
+	ljca = dev_get_drvdata(pdev->dev.parent);
+	ljca_pdata = dev_get_platdata(&pdev->dev);
+	stub = ljca_stub_find(ljca, ljca_pdata->type);
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	spin_lock_irqsave(&stub->event_cb_lock, flags);
+	stub->event_entry.notify = event_cb;
+	stub->event_entry.pdev = pdev;
+	spin_unlock_irqrestore(&stub->event_cb_lock, flags);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ljca_register_event_cb);
+
+void ljca_unregister_event_cb(struct platform_device *pdev)
+{
+	struct ljca_platform_data *ljca_pdata;
+	struct ljca_dev *ljca;
+	struct ljca_stub *stub;
+	unsigned long flags;
+
+	ljca = dev_get_drvdata(pdev->dev.parent);
+	ljca_pdata = dev_get_platdata(&pdev->dev);
+	stub = ljca_stub_find(ljca, ljca_pdata->type);
+	if (IS_ERR(stub))
+		return;
+
+	spin_lock_irqsave(&stub->event_cb_lock, flags);
+	stub->event_entry.notify = NULL;
+	stub->event_entry.pdev = NULL;
+	spin_unlock_irqrestore(&stub->event_cb_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ljca_unregister_event_cb);
+
+static void ljca_stub_cleanup(struct ljca_dev *ljca)
+{
+	struct ljca_stub *stub;
+	struct ljca_stub *next;
+
+	list_for_each_entry_safe (stub, next, &ljca->stubs_list, list) {
+		list_del_init(&stub->list);
+		kfree(stub);
+	}
+}
+
+static void ljca_read_complete(struct urb *urb)
+{
+	struct ljca_dev *ljca = urb->context;
+	struct ljca_msg *header = urb->transfer_buffer;
+	int len = urb->actual_length;
+	int ret;
+
+	dev_dbg(&ljca->intf->dev,
+		"bulk read urb got message from fw, status:%d data_len:%d\n",
+		urb->status, urb->actual_length);
+
+	BUG_ON(!ljca);
+	BUG_ON(!header);
+
+	if (urb->status) {
+		/* sync/async unlink faults aren't errors */
+		if (urb->status == -ENOENT || urb->status == -ECONNRESET ||
+		    urb->status == -ESHUTDOWN)
+			return;
+
+		dev_err(&ljca->intf->dev, "read bulk urb transfer failed: %d\n",
+			urb->status);
+		goto resubmit;
+	}
+
+	dev_dbg(&ljca->intf->dev, "receive: type:%d cmd:%d flags:%d len:%d\n",
+		header->type, header->cmd, header->flags, header->len);
+	ljca_dump(ljca, header->data, header->len);
+
+	if (!ljca_validate(header, len)) {
+		dev_err(&ljca->intf->dev,
+			"data not correct header->len:%d payload_len:%d\n ",
+			header->len, len);
+		goto resubmit;
+	}
+
+	ret = ljca_parse(ljca, header);
+	if (ret)
+		dev_err(&ljca->intf->dev,
+			"failed to parse data: ret:%d type:%d len: %d", ret,
+			header->type, header->len);
+
+resubmit:
+	ret = usb_submit_urb(urb, GFP_KERNEL);
+	if (ret)
+		dev_err(&ljca->intf->dev,
+			"failed submitting read urb, error %d\n", ret);
+}
+
+static int ljca_start(struct ljca_dev *ljca)
+{
+	int ret;
+
+	usb_fill_bulk_urb(ljca->in_urb, ljca->udev,
+			  usb_rcvbulkpipe(ljca->udev, ljca->in_ep), ljca->ibuf,
+			  ljca->ibuf_len, ljca_read_complete, ljca);
+
+	ret = usb_submit_urb(ljca->in_urb, GFP_KERNEL);
+	if (ret) {
+		dev_err(&ljca->intf->dev,
+			"failed submitting read urb, error %d\n", ret);
+	}
+	return ret;
+}
+
+struct ljca_mng_priv {
+	long reset_id;
+};
+
+static int ljca_mng_reset_handshake(struct ljca_stub *stub)
+{
+	int ret;
+	struct ljca_mng_priv *priv;
+	__le32 reset_id;
+	__le32 reset_id_ret = 0;
+	int ilen;
+
+	priv = ljca_priv(stub);
+	reset_id = cpu_to_le32(priv->reset_id++);
+	ret = ljca_stub_write(stub, MNG_RESET_NOTIFY, &reset_id,
+			      sizeof(reset_id), &reset_id_ret, &ilen, true,
+			      USB_WRITE_ACK_TIMEOUT);
+	if (ret || ilen != sizeof(reset_id_ret) || reset_id_ret != reset_id) {
+		dev_err(&stub->intf->dev,
+			"MNG_RESET_NOTIFY failed reset_id:%d/%d ret:%d\n",
+			le32_to_cpu(reset_id_ret), le32_to_cpu(reset_id), ret);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static inline int ljca_mng_reset(struct ljca_stub *stub)
+{
+	return ljca_stub_write(stub, MNG_RESET, NULL, 0, NULL, NULL, true,
+			       USB_WRITE_ACK_TIMEOUT);
+}
+
+static int ljca_add_mfd_cell(struct ljca_dev *ljca, struct mfd_cell *cell)
+{
+	struct mfd_cell *new_cells;
+
+	/* Enumerate the device even if it does not appear in DSDT */
+	if (!cell->acpi_match->pnpid)
+		dev_warn(&ljca->intf->dev,
+			 "The HID of cell %s does not exist in DSDT\n",
+			 cell->name);
+
+	new_cells = krealloc_array(ljca->cells, (ljca->cell_count + 1),
+				   sizeof(struct mfd_cell), GFP_KERNEL);
+	if (!new_cells)
+		return -ENOMEM;
+
+	memcpy(&new_cells[ljca->cell_count], cell, sizeof(*cell));
+	ljca->cells = new_cells;
+	ljca->cell_count++;
+
+	return 0;
+}
+
+static int ljca_gpio_stub_init(struct ljca_dev *ljca,
+			       struct ljca_gpio_descriptor *desc)
+{
+	struct ljca_stub *stub;
+	struct mfd_cell cell = { 0 };
+	struct ljca_platform_data *pdata;
+	int gpio_num = desc->pins_per_bank * desc->bank_num;
+	int i;
+	u32 valid_pin[MAX_GPIO_NUM / (sizeof(u32) * BITS_PER_BYTE)];
+
+	if (gpio_num > MAX_GPIO_NUM)
+		return -EINVAL;
+
+	stub = ljca_stub_alloc(ljca, sizeof(*pdata));
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	stub->type = GPIO_STUB;
+	stub->intf = ljca->intf;
+
+	pdata = ljca_priv(stub);
+	pdata->type = stub->type;
+	pdata->gpio_info.num = gpio_num;
+
+	for (i = 0; i < desc->bank_num; i++)
+		valid_pin[i] = desc->bank_desc[i].valid_pins;
+
+	bitmap_from_arr32(pdata->gpio_info.valid_pin_map, valid_pin, gpio_num);
+
+	cell.name = "ljca-gpio";
+	cell.platform_data = pdata;
+	cell.pdata_size = sizeof(*pdata);
+	cell.acpi_match = &ljca_acpi_match_gpio;
+
+	return ljca_add_mfd_cell(ljca, &cell);
+}
+
+static int ljca_mng_enum_gpio(struct ljca_stub *stub)
+{
+	struct ljca_dev *ljca = usb_get_intfdata(stub->intf);
+	struct ljca_gpio_descriptor *desc;
+	int ret;
+	int len;
+
+	desc = kzalloc(MAX_PAYLOAD_SIZE, GFP_KERNEL);
+	if (!desc)
+		return -ENOMEM;
+
+	ret = ljca_stub_write(stub, MNG_ENUM_GPIO, NULL, 0, desc, &len, true,
+			      USB_ENUM_STUB_TIMEOUT);
+	if (ret || len != sizeof(*desc) + desc->bank_num *
+						  sizeof(desc->bank_desc[0])) {
+		dev_err(&stub->intf->dev,
+			"enum gpio failed ret:%d len:%d bank_num:%d\n", ret,
+			len, desc->bank_num);
+		kfree(desc);
+		return -EIO;
+	}
+
+	ret = ljca_gpio_stub_init(ljca, desc);
+	kfree(desc);
+	return ret;
+}
+
+static int ljca_i2c_stub_init(struct ljca_dev *ljca,
+			      struct ljca_i2c_descriptor *desc)
+{
+	struct ljca_stub *stub;
+	struct ljca_platform_data *pdata;
+	int i;
+	int ret;
+
+	stub = ljca_stub_alloc(ljca, desc->num * sizeof(*pdata));
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	stub->type = I2C_STUB;
+	stub->intf = ljca->intf;
+	pdata = ljca_priv(stub);
+
+	for (i = 0; i < desc->num; i++) {
+		struct mfd_cell cell = { 0 };
+		pdata[i].type = stub->type;
+
+		pdata[i].i2c_info.id = desc->info[i].id;
+		pdata[i].i2c_info.capacity = desc->info[i].capacity;
+		pdata[i].i2c_info.intr_pin = desc->info[i].intr_pin;
+
+		cell.name = "ljca-i2c";
+		cell.platform_data = &pdata[i];
+		cell.pdata_size = sizeof(pdata[i]);
+		if (i < ARRAY_SIZE(ljca_acpi_match_i2cs))
+			cell.acpi_match = &ljca_acpi_match_i2cs[i];
+
+		ret = ljca_add_mfd_cell(ljca, &cell);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int ljca_mng_enum_i2c(struct ljca_stub *stub)
+{
+	struct ljca_dev *ljca = usb_get_intfdata(stub->intf);
+	struct ljca_i2c_descriptor *desc;
+	int ret;
+	int len;
+
+	desc = kzalloc(MAX_PAYLOAD_SIZE, GFP_KERNEL);
+	if (!desc)
+		return -ENOMEM;
+
+	ret = ljca_stub_write(stub, MNG_ENUM_I2C, NULL, 0, desc, &len, true,
+			      USB_ENUM_STUB_TIMEOUT);
+	if (ret) {
+		dev_err(&stub->intf->dev,
+			"MNG_ENUM_I2C failed ret:%d len:%d num:%d\n", ret, len,
+			desc->num);
+		kfree(desc);
+		return -EIO;
+	}
+
+	ret = ljca_i2c_stub_init(ljca, desc);
+	kfree(desc);
+	return ret;
+}
+
+static int ljca_spi_stub_init(struct ljca_dev *ljca,
+			      struct ljca_spi_descriptor *desc)
+{
+	struct ljca_stub *stub;
+	struct ljca_platform_data *pdata;
+	int i;
+	int ret;
+
+	stub = ljca_stub_alloc(ljca, desc->num * sizeof(*pdata));
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	stub->type = SPI_STUB;
+	stub->intf = ljca->intf;
+	pdata = ljca_priv(stub);
+
+	for (i = 0; i < desc->num; i++) {
+		struct mfd_cell cell = { 0 };
+		pdata[i].type = stub->type;
+
+		pdata[i].spi_info.id = desc->info[i].id;
+		pdata[i].spi_info.capacity = desc->info[i].capacity;
+
+		cell.name = "ljca-spi";
+		cell.platform_data = &pdata[i];
+		cell.pdata_size = sizeof(pdata[i]);
+		if (i < ARRAY_SIZE(ljca_acpi_match_spis))
+			cell.acpi_match = &ljca_acpi_match_spis[i];
+
+		ret = ljca_add_mfd_cell(ljca, &cell);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int ljca_mng_enum_spi(struct ljca_stub *stub)
+{
+	struct ljca_dev *ljca = usb_get_intfdata(stub->intf);
+	struct ljca_spi_descriptor *desc;
+	int ret;
+	int len;
+
+	desc = kzalloc(MAX_PAYLOAD_SIZE, GFP_KERNEL);
+	if (!desc)
+		return -ENOMEM;
+
+	ret = ljca_stub_write(stub, MNG_ENUM_SPI, NULL, 0, desc, &len, true,
+			      USB_ENUM_STUB_TIMEOUT);
+	if (ret) {
+		dev_err(&stub->intf->dev,
+			"MNG_ENUM_SPI failed ret:%d len:%d num:%d\n", ret, len,
+			desc->num);
+		kfree(desc);
+		return -EIO;
+	}
+
+	ret = ljca_spi_stub_init(ljca, desc);
+	kfree(desc);
+	return ret;
+}
+
+static int ljca_mng_get_version(struct ljca_stub *stub, char *buf)
+{
+	struct fw_version version = { 0 };
+	int ret;
+	int len;
+
+	if (!buf)
+		return -EINVAL;
+
+	ret = ljca_stub_write(stub, MNG_GET_VERSION, NULL, 0, &version, &len,
+			      true, USB_WRITE_ACK_TIMEOUT);
+	if (ret || len < sizeof(struct fw_version)) {
+		dev_err(&stub->intf->dev,
+			"MNG_GET_VERSION failed ret:%d len:%d\n", ret, len);
+		return ret;
+	}
+
+	return sysfs_emit(buf, "%d.%d.%d.%d\n", version.major, version.minor,
+			  le16_to_cpu(version.patch),
+			  le16_to_cpu(version.build));
+}
+
+static inline int ljca_mng_set_dfu_mode(struct ljca_stub *stub)
+{
+	return ljca_stub_write(stub, MNG_SET_DFU_MODE, NULL, 0, NULL, NULL,
+			       true, USB_WRITE_ACK_TIMEOUT);
+}
+
+static int ljca_mng_link(struct ljca_dev *ljca, struct ljca_stub *stub)
+{
+	int ret;
+
+	ret = ljca_mng_reset_handshake(stub);
+	if (ret)
+		return ret;
+
+	ljca->state = LJCA_RESET_SYNCED;
+
+	/* workaround for FW limitation, ignore return value of enum result */
+	ljca_mng_enum_gpio(stub);
+	ljca->state = LJCA_ENUM_GPIO_COMPLETE;
+
+	ljca_mng_enum_i2c(stub);
+	ljca->state = LJCA_ENUM_I2C_COMPLETE;
+
+	ljca_mng_enum_spi(stub);
+	ljca->state = LJCA_ENUM_SPI_COMPLETE;
+
+	return 0;
+}
+
+static int ljca_mng_init(struct ljca_dev *ljca)
+{
+	struct ljca_stub *stub;
+	struct ljca_mng_priv *priv;
+	int ret;
+
+	stub = ljca_stub_alloc(ljca, sizeof(*priv));
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	priv = ljca_priv(stub);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->reset_id = 0;
+	stub->type = MNG_STUB;
+	stub->intf = ljca->intf;
+
+	ret = ljca_mng_link(ljca, stub);
+	if (ret)
+		dev_err(&ljca->intf->dev,
+			"mng stub link done ret:%d state:%d\n", ret,
+			ljca->state);
+
+	return ret;
+}
+
+static inline int ljca_diag_get_fw_log(struct ljca_stub *stub, void *buf)
+{
+	int ret;
+	int len;
+
+	if (!buf)
+		return -EINVAL;
+
+	ret = ljca_stub_write(stub, DIAG_GET_FW_LOG, NULL, 0, buf, &len, true,
+			      USB_WRITE_ACK_TIMEOUT);
+	if (ret)
+		return ret;
+
+	return len;
+}
+
+static inline int ljca_diag_get_coredump(struct ljca_stub *stub, void *buf)
+{
+	int ret;
+	int len;
+
+	if (!buf)
+		return -EINVAL;
+
+	ret = ljca_stub_write(stub, DIAG_GET_FW_COREDUMP, NULL, 0, buf, &len,
+			      true, USB_WRITE_ACK_TIMEOUT);
+	if (ret)
+		return ret;
+
+	return len;
+}
+
+static inline int ljca_diag_set_trace_level(struct ljca_stub *stub, u8 level)
+{
+	return ljca_stub_write(stub, DIAG_SET_TRACE_LEVEL, &level,
+			       sizeof(level), NULL, NULL, true,
+			       USB_WRITE_ACK_TIMEOUT);
+}
+
+static int ljca_diag_init(struct ljca_dev *ljca)
+{
+	struct ljca_stub *stub;
+
+	stub = ljca_stub_alloc(ljca, 0);
+	if (IS_ERR(stub))
+		return PTR_ERR(stub);
+
+	stub->type = DIAG_STUB;
+	stub->intf = ljca->intf;
+	return 0;
+}
+
+static void ljca_delete(struct ljca_dev *ljca)
+{
+	mutex_destroy(&ljca->mutex);
+	usb_free_urb(ljca->in_urb);
+	usb_put_intf(ljca->intf);
+	usb_put_dev(ljca->udev);
+	kfree(ljca->ibuf);
+	kfree(ljca->cells);
+	kfree(ljca);
+}
+
+static int ljca_init(struct ljca_dev *ljca)
+{
+	mutex_init(&ljca->mutex);
+	init_waitqueue_head(&ljca->ack_wq);
+	INIT_LIST_HEAD(&ljca->stubs_list);
+
+	ljca->state = LJCA_INITED;
+
+	return 0;
+}
+
+static void ljca_stop(struct ljca_dev *ljca)
+{
+	usb_kill_urb(ljca->in_urb);
+}
+
+static ssize_t cmd_store(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	struct usb_interface *intf = to_usb_interface(dev);
+	struct ljca_dev *ljca = usb_get_intfdata(intf);
+	struct ljca_stub *mng_stub = ljca_stub_find(ljca, MNG_STUB);
+	struct ljca_stub *diag_stub = ljca_stub_find(ljca, DIAG_STUB);
+
+	if (sysfs_streq(buf, "dfu"))
+		ljca_mng_set_dfu_mode(mng_stub);
+	else if (sysfs_streq(buf, "reset"))
+		ljca_mng_reset(mng_stub);
+	else if (sysfs_streq(buf, "debug"))
+		ljca_diag_set_trace_level(diag_stub, 3);
+
+	return count;
+}
+
+static ssize_t cmd_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	return sysfs_emit(buf, "%s\n", "supported cmd: [dfu, reset, debug]");
+}
+static DEVICE_ATTR_RW(cmd);
+
+static ssize_t version_show(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	struct usb_interface *intf = to_usb_interface(dev);
+	struct ljca_dev *ljca = usb_get_intfdata(intf);
+	struct ljca_stub *stub = ljca_stub_find(ljca, MNG_STUB);
+
+	return ljca_mng_get_version(stub, buf);
+}
+static DEVICE_ATTR_RO(version);
+
+static ssize_t log_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct usb_interface *intf = to_usb_interface(dev);
+	struct ljca_dev *ljca = usb_get_intfdata(intf);
+	struct ljca_stub *diag_stub = ljca_stub_find(ljca, DIAG_STUB);
+
+	return ljca_diag_get_fw_log(diag_stub, buf);
+}
+static DEVICE_ATTR_RO(log);
+
+static ssize_t coredump_show(struct device *dev, struct device_attribute *attr,
+			     char *buf)
+{
+	struct usb_interface *intf = to_usb_interface(dev);
+	struct ljca_dev *ljca = usb_get_intfdata(intf);
+	struct ljca_stub *diag_stub = ljca_stub_find(ljca, DIAG_STUB);
+
+	return ljca_diag_get_coredump(diag_stub, buf);
+}
+static DEVICE_ATTR_RO(coredump);
+
+static struct attribute *ljca_attrs[] = {
+	&dev_attr_version.attr,
+	&dev_attr_cmd.attr,
+	&dev_attr_log.attr,
+	&dev_attr_coredump.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(ljca);
+
+static int ljca_probe(struct usb_interface *intf,
+		      const struct usb_device_id *id)
+{
+	struct ljca_dev *ljca;
+	struct usb_endpoint_descriptor *bulk_in, *bulk_out;
+	int ret;
+
+	ret = precheck_acpi_hid(intf);
+	if (ret)
+		return ret;
+
+	/* allocate memory for our device state and initialize it */
+	ljca = kzalloc(sizeof(*ljca), GFP_KERNEL);
+	if (!ljca)
+		return -ENOMEM;
+
+	ljca_init(ljca);
+	ljca->udev = usb_get_dev(interface_to_usbdev(intf));
+	ljca->intf = usb_get_intf(intf);
+
+	/* set up the endpoint information use only the first bulk-in and bulk-out endpoints */
+	ret = usb_find_common_endpoints(intf->cur_altsetting, &bulk_in,
+					&bulk_out, NULL, NULL);
+	if (ret) {
+		dev_err(&intf->dev,
+			"Could not find both bulk-in and bulk-out endpoints\n");
+		goto error;
+	}
+
+	ljca->ibuf_len = usb_endpoint_maxp(bulk_in);
+	ljca->in_ep = bulk_in->bEndpointAddress;
+	ljca->ibuf = kzalloc(ljca->ibuf_len, GFP_KERNEL);
+	if (!ljca->ibuf) {
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	ljca->in_urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!ljca->in_urb) {
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	ljca->out_ep = bulk_out->bEndpointAddress;
+	dev_dbg(&intf->dev, "bulk_in size:%zu addr:%d bulk_out addr:%d\n",
+		ljca->ibuf_len, ljca->in_ep, ljca->out_ep);
+
+	/* save our data pointer in this intf device */
+	usb_set_intfdata(intf, ljca);
+	ret = ljca_start(ljca);
+	if (ret) {
+		dev_err(&intf->dev, "bridge read start failed ret %d\n", ret);
+		goto error;
+	}
+
+	ret = ljca_mng_init(ljca);
+	if (ret) {
+		dev_err(&intf->dev, "register mng stub failed ret %d\n", ret);
+		goto error_stop;
+	}
+
+	ret = ljca_diag_init(ljca);
+	if (ret) {
+		dev_err(&intf->dev, "register diag stub failed ret %d\n", ret);
+		goto error_stop;
+	}
+
+	ret = mfd_add_hotplug_devices(&intf->dev, ljca->cells,
+				      ljca->cell_count);
+	if (ret) {
+		dev_err(&intf->dev, "failed to add mfd devices to core %d\n",
+			ljca->cell_count);
+		goto error_stop;
+	}
+
+	ljca->state = LJCA_STARTED;
+	dev_info(&intf->dev, "LJCA USB device init success\n");
+	return 0;
+error_stop:
+	ljca_stop(ljca);
+error:
+	dev_err(&intf->dev, "LJCA USB device init failed\n");
+	/* this frees allocated memory */
+	ljca_stub_cleanup(ljca);
+	ljca_delete(ljca);
+	return ret;
+}
+
+static void ljca_disconnect(struct usb_interface *intf)
+{
+	struct ljca_dev *ljca;
+
+	ljca = usb_get_intfdata(intf);
+
+	ljca_stop(ljca);
+	ljca->state = LJCA_STOPPED;
+	mfd_remove_devices(&intf->dev);
+	ljca_stub_cleanup(ljca);
+	usb_set_intfdata(intf, NULL);
+	ljca_delete(ljca);
+	dev_info(&intf->dev, "LJCA disconnected\n");
+}
+
+static int ljca_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct ljca_dev *ljca = usb_get_intfdata(intf);
+
+	ljca_stop(ljca);
+	ljca->state = LJCA_SUSPEND;
+
+	dev_dbg(&intf->dev, "LJCA suspend\n");
+	return 0;
+}
+
+static int ljca_resume(struct usb_interface *intf)
+{
+	struct ljca_dev *ljca = usb_get_intfdata(intf);
+
+	ljca->state = LJCA_STARTED;
+	dev_dbg(&intf->dev, "LJCA resume\n");
+	return ljca_start(ljca);
+}
+
+static const struct usb_device_id ljca_table[] = {
+	{USB_DEVICE(0x8086, 0x0b63)},
+	{}
+};
+MODULE_DEVICE_TABLE(usb, ljca_table);
+
+static struct usb_driver ljca_driver = {
+	.name = "ljca",
+	.probe = ljca_probe,
+	.disconnect = ljca_disconnect,
+	.suspend = ljca_suspend,
+	.resume = ljca_resume,
+	.id_table = ljca_table,
+	.dev_groups = ljca_groups,
+	.supports_autosuspend = 1,
+};
+
+module_usb_driver(ljca_driver);
+
+MODULE_AUTHOR("Ye Xiang <xiang.ye@intel.com>");
+MODULE_AUTHOR("Zhang Lixu <lixu.zhang@intel.com>");
+MODULE_DESCRIPTION("Intel La Jolla Cove Adapter USB driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/lp8788-irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/lp8788-irq.c
@@ -175,6 +175,7 @@
 				IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 				"lp8788-irq", irqd);
 	if (ret) {
+		irq_domain_remove(lp->irqdm);
 		dev_err(lp->dev, "failed to create a thread for IRQ_N\n");
 		return ret;
 	}
@@ -188,4 +189,6 @@
 {
 	if (lp->irq)
 		free_irq(lp->irq, lp->irqdm);
+	if (lp->irqdm)
+		irq_domain_remove(lp->irqdm);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/lp8788.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/lp8788.c
@@ -195,8 +195,16 @@
 	if (ret)
 		return ret;
 
-	return mfd_add_devices(lp->dev, -1, lp8788_devs,
-			       ARRAY_SIZE(lp8788_devs), NULL, 0, NULL);
+	ret = mfd_add_devices(lp->dev, -1, lp8788_devs,
+			      ARRAY_SIZE(lp8788_devs), NULL, 0, NULL);
+	if (ret)
+		goto err_exit_irq;
+
+	return 0;
+
+err_exit_irq:
+	lp8788_irq_exit(lp);
+	return ret;
 }
 
 static int lp8788_remove(struct i2c_client *cl)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/lpc_ich.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/lpc_ich.c
@@ -63,6 +63,8 @@
 #define SPIBASE_BYT		0x54
 #define SPIBASE_BYT_SZ		512
 #define SPIBASE_BYT_EN		BIT(1)
+#define BYT_BCR			0xfc
+#define BYT_BCR_WPD		BIT(0)
 
 #define SPIBASE_LPT		0x3800
 #define SPIBASE_LPT_SZ		512
@@ -686,8 +688,9 @@
 	{ PCI_VDEVICE(INTEL, 0x2917), LPC_ICH9ME},
 	{ PCI_VDEVICE(INTEL, 0x2918), LPC_ICH9},
 	{ PCI_VDEVICE(INTEL, 0x2919), LPC_ICH9M},
-	{ PCI_VDEVICE(INTEL, 0x3197), LPC_GLK},
 	{ PCI_VDEVICE(INTEL, 0x2b9c), LPC_COUGARMOUNTAIN},
+	{ PCI_VDEVICE(INTEL, 0x3197), LPC_GLK},
+	{ PCI_VDEVICE(INTEL, 0x31e8), LPC_GLK},
 	{ PCI_VDEVICE(INTEL, 0x3a14), LPC_ICH10DO},
 	{ PCI_VDEVICE(INTEL, 0x3a16), LPC_ICH10R},
 	{ PCI_VDEVICE(INTEL, 0x3a18), LPC_ICH10},
@@ -1084,12 +1087,57 @@
 	return ret;
 }
 
+static bool lpc_ich_byt_set_writeable(void __iomem *base, void *data)
+{
+	u32 val;
+
+	val = readl(base + BYT_BCR);
+	if (!(val & BYT_BCR_WPD)) {
+		val |= BYT_BCR_WPD;
+		writel(val, base + BYT_BCR);
+		val = readl(base + BYT_BCR);
+	}
+
+	return val & BYT_BCR_WPD;
+}
+
+static bool lpc_ich_lpt_set_writeable(void __iomem *base, void *data)
+{
+	struct pci_dev *pdev = data;
+	u32 bcr;
+
+	pci_read_config_dword(pdev, BCR, &bcr);
+	if (!(bcr & BCR_WPD)) {
+		bcr |= BCR_WPD;
+		pci_write_config_dword(pdev, BCR, bcr);
+		pci_read_config_dword(pdev, BCR, &bcr);
+	}
+
+	return bcr & BCR_WPD;
+}
+
+static bool lpc_ich_bxt_set_writeable(void __iomem *base, void *data)
+{
+	unsigned int spi = PCI_DEVFN(13, 2);
+	struct pci_bus *bus = data;
+	u32 bcr;
+
+	pci_bus_read_config_dword(bus, spi, BCR, &bcr);
+	if (!(bcr & BCR_WPD)) {
+		bcr |= BCR_WPD;
+		pci_bus_write_config_dword(bus, spi, BCR, bcr);
+		pci_bus_read_config_dword(bus, spi, BCR, &bcr);
+	}
+
+	return bcr & BCR_WPD;
+}
+
 static int lpc_ich_init_spi(struct pci_dev *dev)
 {
 	struct lpc_ich_priv *priv = pci_get_drvdata(dev);
 	struct resource *res = &intel_spi_res[0];
 	struct intel_spi_boardinfo *info;
-	u32 spi_base, rcba, bcr;
+	u32 spi_base, rcba;
 
 	info = devm_kzalloc(&dev->dev, sizeof(*info), GFP_KERNEL);
 	if (!info)
@@ -1103,6 +1151,8 @@
 		if (spi_base & SPIBASE_BYT_EN) {
 			res->start = spi_base & ~(SPIBASE_BYT_SZ - 1);
 			res->end = res->start + SPIBASE_BYT_SZ - 1;
+
+			info->set_writeable = lpc_ich_byt_set_writeable;
 		}
 		break;
 
@@ -1113,8 +1163,8 @@
 			res->start = spi_base + SPIBASE_LPT;
 			res->end = res->start + SPIBASE_LPT_SZ - 1;
 
-			pci_read_config_dword(dev, BCR, &bcr);
-			info->writeable = !!(bcr & BCR_WPD);
+			info->set_writeable = lpc_ich_lpt_set_writeable;
+			info->data = dev;
 		}
 		break;
 
@@ -1135,8 +1185,8 @@
 			res->start = spi_base & 0xfffffff0;
 			res->end = res->start + SPIBASE_APL_SZ - 1;
 
-			pci_bus_read_config_dword(bus, spi, BCR, &bcr);
-			info->writeable = !!(bcr & BCR_WPD);
+			info->set_writeable = lpc_ich_bxt_set_writeable;
+			info->data = bus;
 		}
 
 		pci_bus_write_config_byte(bus, p2sb, 0xe1, 0x1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/max77620.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/max77620.c
@@ -419,9 +419,11 @@
 		ret = max77620_config_fps(chip, fps_child);
 		if (ret < 0) {
 			of_node_put(fps_child);
+			of_node_put(fps_np);
 			return ret;
 		}
 	}
+	of_node_put(fps_np);
 
 	config = chip->enable_global_lpm ? MAX77620_ONOFFCNFG2_SLP_LPM_MSK : 0;
 	ret = regmap_update_bits(chip->rmap, MAX77620_REG_ONOFFCNFG2,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/mc13xxx-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/mc13xxx-core.c
@@ -323,8 +323,10 @@
 		adc1 |= MC13783_ADC1_ATOX;
 
 	dev_dbg(mc13xxx->dev, "%s: request irq\n", __func__);
-	mc13xxx_irq_request(mc13xxx, MC13XXX_IRQ_ADCDONE,
+	ret = mc13xxx_irq_request(mc13xxx, MC13XXX_IRQ_ADCDONE,
 			mc13xxx_handler_adcdone, __func__, &adcdone_data);
+	if (ret)
+		goto out;
 
 	mc13xxx_reg_write(mc13xxx, MC13XXX_ADC0, adc0);
 	mc13xxx_reg_write(mc13xxx, MC13XXX_ADC1, adc1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/mfd-aaeon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/mfd-aaeon.c
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * UP Board main platform driver and FPGA configuration support
+ *
+ * Copyright (c) 2021, AAEON Ltd.
+ *
+ * Author: Kunyang_Fan <knuyang_fan@aaeon.com.tw>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/platform_data/x86/asus-wmi.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/wmi.h>
+
+#define AAEON_WMI_MGMT_GUID      "97845ED0-4E6D-11DE-8A39-0800200C9A66"
+
+#define WMI_REPORT_CAPABILITY_METHOD	0x00000000
+#define MAX_BFPI_VERSION		255
+#define GET_REVISION_ID			0x00
+
+struct aaeon_wmi_priv {
+	const struct mfd_cell *cells;
+	size_t ncells;
+};
+
+static const struct mfd_cell aaeon_mfd_cells[] = {
+	{ .name = "gpio-aaeon" },
+	{ .name = "hwmon-aaeon"},
+	{ .name = "leds-aaeon"},
+	{ .name = "wdt-aaeon"},
+};
+
+static const struct aaeon_wmi_priv aaeon_wmi_priv_data = {
+	.cells = aaeon_mfd_cells,
+	.ncells = ARRAY_SIZE(aaeon_mfd_cells),
+};
+
+static int aaeon_wmi_check_device(void)
+{
+	int err;
+	int retval;
+
+	err = asus_wmi_evaluate_method(WMI_REPORT_CAPABILITY_METHOD, GET_REVISION_ID, 0,
+				       &retval);
+	if (err)
+		return -ENODEV;
+	if (retval < 3 || retval > MAX_BFPI_VERSION)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int aaeon_wmi_probe(struct wmi_device *wdev, const void *context)
+{
+	struct aaeon_wmi_priv *priv;
+
+	if (!wmi_has_guid(AAEON_WMI_MGMT_GUID)) {
+		dev_info(&wdev->dev, "AAEON Management GUID not found\n");
+		return -ENODEV;
+	}
+
+	if (aaeon_wmi_check_device())
+		return -ENODEV;
+
+	priv = (struct aaeon_wmi_priv *)context;
+	dev_set_drvdata(&wdev->dev, priv);
+
+	return devm_mfd_add_devices(&wdev->dev, 0, priv->cells,
+				    priv->ncells, NULL, 0, NULL);
+}
+
+static const struct wmi_device_id aaeon_wmi_id_table[] = {
+	{ AAEON_WMI_MGMT_GUID, (void *)&aaeon_wmi_priv_data },
+	{}
+};
+
+static struct wmi_driver aaeon_wmi_driver = {
+	.driver = {
+		.name = "mfd-aaeon",
+	},
+	.id_table = aaeon_wmi_id_table,
+	.probe = aaeon_wmi_probe,
+};
+
+module_wmi_driver(aaeon_wmi_driver);
+
+MODULE_DEVICE_TABLE(wmi, aaeon_wmi_id_table);
+MODULE_AUTHOR("Kunyang Fan <kunyang_fan@aaeon.com.tw>");
+MODULE_DESCRIPTION("AAEON Board WMI driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/mfd-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/mfd-core.c
@@ -159,6 +159,7 @@
 	struct platform_device *pdev;
 	struct device_node *np = NULL;
 	struct mfd_of_node_entry *of_entry, *tmp;
+	bool disabled = false;
 	int ret = -ENOMEM;
 	int platform_id;
 	int r;
@@ -196,22 +197,30 @@
 	if (IS_ENABLED(CONFIG_OF) && parent->of_node && cell->of_compatible) {
 		for_each_child_of_node(parent->of_node, np) {
 			if (of_device_is_compatible(np, cell->of_compatible)) {
-				/* Ignore 'disabled' devices error free */
+				/* Skip 'disabled' devices */
 				if (!of_device_is_available(np)) {
-					ret = 0;
-					goto fail_alias;
+					disabled = true;
+					continue;
 				}
 
 				ret = mfd_match_of_node_to_dev(pdev, np, cell);
 				if (ret == -EAGAIN)
 					continue;
+				of_node_put(np);
 				if (ret)
 					goto fail_alias;
 
-				break;
+				goto match;
 			}
 		}
 
+		if (disabled) {
+			/* Ignore 'disabled' devices error free */
+			ret = 0;
+			goto fail_alias;
+		}
+
+match:
 		if (!pdev->dev.of_node)
 			pr_warn("%s: Failed to locate of_node [id: %d]\n",
 				cell->name, platform_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/motorola-cpcap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/motorola-cpcap.c
@@ -202,6 +202,13 @@
 };
 MODULE_DEVICE_TABLE(of, cpcap_of_match);
 
+static const struct spi_device_id cpcap_spi_ids[] = {
+	{ .name = "cpcap", },
+	{ .name = "6556002", },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, cpcap_spi_ids);
+
 static const struct regmap_config cpcap_regmap_config = {
 	.reg_bits = 16,
 	.reg_stride = 4,
@@ -342,6 +349,7 @@
 		.pm = &cpcap_pm,
 	},
 	.probe = cpcap_probe,
+	.id_table = cpcap_spi_ids,
 };
 module_spi_driver(cpcap_driver);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/mt6360-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/mt6360-core.c
@@ -402,7 +402,7 @@
 	struct mt6360_ddata *ddata = context;
 	u8 bank = *(u8 *)reg;
 	u8 reg_addr = *(u8 *)(reg + 1);
-	struct i2c_client *i2c = ddata->i2c[bank];
+	struct i2c_client *i2c;
 	bool crc_needed = false;
 	u8 *buf;
 	int buf_len = MT6360_ALLOC_READ_SIZE(val_size);
@@ -410,6 +410,11 @@
 	u8 crc;
 	int ret;
 
+	if (bank >= MT6360_SLAVE_MAX)
+		return -EINVAL;
+
+	i2c = ddata->i2c[bank];
+
 	if (bank == MT6360_SLAVE_PMIC || bank == MT6360_SLAVE_LDO) {
 		crc_needed = true;
 		ret = mt6360_xlate_pmicldo_addr(&reg_addr, val_size);
@@ -453,13 +458,18 @@
 	struct mt6360_ddata *ddata = context;
 	u8 bank = *(u8 *)val;
 	u8 reg_addr = *(u8 *)(val + 1);
-	struct i2c_client *i2c = ddata->i2c[bank];
+	struct i2c_client *i2c;
 	bool crc_needed = false;
 	u8 *buf;
 	int buf_len = MT6360_ALLOC_WRITE_SIZE(val_size);
 	int write_size = val_size - MT6360_REGMAP_REG_BYTE_SIZE;
 	int ret;
 
+	if (bank >= MT6360_SLAVE_MAX)
+		return -EINVAL;
+
+	i2c = ddata->i2c[bank];
+
 	if (bank == MT6360_SLAVE_PMIC || bank == MT6360_SLAVE_LDO) {
 		crc_needed = true;
 		ret = mt6360_xlate_pmicldo_addr(&reg_addr, val_size - MT6360_REGMAP_REG_BYTE_SIZE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/omap-usb-tll.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/omap-usb-tll.c
@@ -237,8 +237,7 @@
 		break;
 	}
 
-	tll = devm_kzalloc(dev, sizeof(*tll) + sizeof(tll->ch_clk[nch]),
-			   GFP_KERNEL);
+	tll = devm_kzalloc(dev, struct_size(tll, ch_clk, nch), GFP_KERNEL);
 	if (!tll) {
 		pm_runtime_put_sync(dev);
 		pm_runtime_disable(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/pcf50633-adc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/pcf50633-adc.c
@@ -136,6 +136,7 @@
 			     void *callback_param)
 {
 	struct pcf50633_adc_request *req;
+	int ret;
 
 	/* req is freed when the result is ready, in interrupt handler */
 	req = kmalloc(sizeof(*req), GFP_KERNEL);
@@ -147,7 +148,11 @@
 	req->callback = callback;
 	req->callback_param = callback_param;
 
-	return adc_enqueue_request(pcf, req);
+	ret = adc_enqueue_request(pcf, req);
+	if (ret)
+		kfree(req);
+
+	return ret;
 }
 EXPORT_SYMBOL_GPL(pcf50633_adc_async_read);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/qcom-pm8008.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/qcom-pm8008.c
@@ -54,13 +54,6 @@
 
 #define PM8008_PERIPH_OFFSET(paddr)	(paddr - PM8008_PERIPH_0_BASE)
 
-struct pm8008_data {
-	struct device *dev;
-	struct regmap *regmap;
-	int irq;
-	struct regmap_irq_chip_data *irq_data;
-};
-
 static unsigned int p0_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_0_BASE)};
 static unsigned int p1_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_1_BASE)};
 static unsigned int p2_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_2_BASE)};
@@ -150,7 +143,7 @@
 	.max_register	= 0xFFFF,
 };
 
-static int pm8008_init(struct pm8008_data *chip)
+static int pm8008_init(struct regmap *regmap)
 {
 	int rc;
 
@@ -160,34 +153,31 @@
 	 * This is required to enable the writing of TYPE registers in
 	 * regmap_irq_sync_unlock().
 	 */
-	rc = regmap_write(chip->regmap,
-			 (PM8008_TEMP_ALARM_ADDR | INT_SET_TYPE_OFFSET),
-			 BIT(0));
+	rc = regmap_write(regmap, (PM8008_TEMP_ALARM_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
 	if (rc)
 		return rc;
 
 	/* Do the same for GPIO1 and GPIO2 peripherals */
-	rc = regmap_write(chip->regmap,
-			 (PM8008_GPIO1_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
+	rc = regmap_write(regmap, (PM8008_GPIO1_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
 	if (rc)
 		return rc;
 
-	rc = regmap_write(chip->regmap,
-			 (PM8008_GPIO2_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
+	rc = regmap_write(regmap, (PM8008_GPIO2_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
 
 	return rc;
 }
 
-static int pm8008_probe_irq_peripherals(struct pm8008_data *chip,
+static int pm8008_probe_irq_peripherals(struct device *dev,
+					struct regmap *regmap,
 					int client_irq)
 {
 	int rc, i;
 	struct regmap_irq_type *type;
 	struct regmap_irq_chip_data *irq_data;
 
-	rc = pm8008_init(chip);
+	rc = pm8008_init(regmap);
 	if (rc) {
-		dev_err(chip->dev, "Init failed: %d\n", rc);
+		dev_err(dev, "Init failed: %d\n", rc);
 		return rc;
 	}
 
@@ -207,10 +197,10 @@
 				IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
 	}
 
-	rc = devm_regmap_add_irq_chip(chip->dev, chip->regmap, client_irq,
+	rc = devm_regmap_add_irq_chip(dev, regmap, client_irq,
 			IRQF_SHARED, 0, &pm8008_irq_chip, &irq_data);
 	if (rc) {
-		dev_err(chip->dev, "Failed to add IRQ chip: %d\n", rc);
+		dev_err(dev, "Failed to add IRQ chip: %d\n", rc);
 		return rc;
 	}
 
@@ -220,32 +210,30 @@
 static int pm8008_probe(struct i2c_client *client)
 {
 	int rc;
-	struct pm8008_data *chip;
-
-	chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
-	if (!chip)
-		return -ENOMEM;
+	struct device *dev;
+	struct regmap *regmap;
 
-	chip->dev = &client->dev;
-	chip->regmap = devm_regmap_init_i2c(client, &qcom_mfd_regmap_cfg);
-	if (!chip->regmap)
-		return -ENODEV;
+	dev = &client->dev;
+	regmap = devm_regmap_init_i2c(client, &qcom_mfd_regmap_cfg);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
 
-	i2c_set_clientdata(client, chip);
+	i2c_set_clientdata(client, regmap);
 
-	if (of_property_read_bool(chip->dev->of_node, "interrupt-controller")) {
-		rc = pm8008_probe_irq_peripherals(chip, client->irq);
+	if (of_property_read_bool(dev->of_node, "interrupt-controller")) {
+		rc = pm8008_probe_irq_peripherals(dev, regmap, client->irq);
 		if (rc)
-			dev_err(chip->dev, "Failed to probe irq periphs: %d\n", rc);
+			dev_err(dev, "Failed to probe irq periphs: %d\n", rc);
 	}
 
-	return devm_of_platform_populate(chip->dev);
+	return devm_of_platform_populate(dev);
 }
 
 static const struct of_device_id pm8008_match[] = {
 	{ .compatible = "qcom,pm8008", },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, pm8008_match);
 
 static struct i2c_driver pm8008_mfd_driver = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/qcom_rpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/qcom_rpm.c
@@ -547,7 +547,7 @@
 	init_completion(&rpm->ack);
 
 	/* Enable message RAM clock */
-	rpm->ramclk = devm_clk_get(&pdev->dev, "ram");
+	rpm->ramclk = devm_clk_get_enabled(&pdev->dev, "ram");
 	if (IS_ERR(rpm->ramclk)) {
 		ret = PTR_ERR(rpm->ramclk);
 		if (ret == -EPROBE_DEFER)
@@ -558,7 +558,6 @@
 		 */
 		rpm->ramclk = NULL;
 	}
-	clk_prepare_enable(rpm->ramclk); /* Accepts NULL */
 
 	irq_ack = platform_get_irq_byname(pdev, "ack");
 	if (irq_ack < 0)
@@ -673,22 +672,11 @@
 	if (ret)
 		dev_warn(&pdev->dev, "failed to mark wakeup irq as wakeup\n");
 
-	return of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
-}
-
-static int qcom_rpm_remove(struct platform_device *pdev)
-{
-	struct qcom_rpm *rpm = dev_get_drvdata(&pdev->dev);
-
-	of_platform_depopulate(&pdev->dev);
-	clk_disable_unprepare(rpm->ramclk);
-
-	return 0;
+	return devm_of_platform_populate(&pdev->dev);
 }
 
 static struct platform_driver qcom_rpm_driver = {
 	.probe = qcom_rpm_probe,
-	.remove = qcom_rpm_remove,
 	.driver  = {
 		.name  = "qcom_rpm",
 		.of_match_table = qcom_rpm_of_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/rsmu_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/rsmu_core.c
@@ -78,11 +78,13 @@
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(rsmu_core_init);
 
 void rsmu_core_exit(struct rsmu_ddata *rsmu)
 {
 	mutex_destroy(&rsmu->lock);
 }
+EXPORT_SYMBOL_GPL(rsmu_core_exit);
 
 MODULE_DESCRIPTION("Renesas SMU core driver");
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/rt5033.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/rt5033.c
@@ -42,9 +42,6 @@
 		.name = "rt5033-charger",
 		.of_compatible = "richtek,rt5033-charger",
 	}, {
-		.name = "rt5033-battery",
-		.of_compatible = "richtek,rt5033-battery",
-	}, {
 		.name = "rt5033-led",
 		.of_compatible = "richtek,rt5033-led",
 	},
@@ -85,8 +82,8 @@
 	}
 	dev_info(&i2c->dev, "Device found Device ID: %04x\n", dev_id);
 
-	ret = regmap_add_irq_chip(rt5033->regmap, rt5033->irq,
-			IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+	ret = devm_regmap_add_irq_chip(rt5033->dev, rt5033->regmap,
+			rt5033->irq, IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 			0, &rt5033_irq_chip, &rt5033->irq_data);
 	if (ret) {
 		dev_err(&i2c->dev, "Failed to request IRQ %d: %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/sm501.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/sm501.c
@@ -920,7 +920,7 @@
 {
 	struct sm501_gpio_chip *smchip = gpiochip_get_data(chip);
 	struct sm501_gpio *smgpio = smchip->ourgpio;
-	unsigned long bit = 1 << offset;
+	unsigned long bit = BIT(offset);
 	void __iomem *regs = smchip->regbase;
 	unsigned long save;
 	unsigned long val;
@@ -946,7 +946,7 @@
 	struct sm501_gpio_chip *smchip = gpiochip_get_data(chip);
 	struct sm501_gpio *smgpio = smchip->ourgpio;
 	void __iomem *regs = smchip->regbase;
-	unsigned long bit = 1 << offset;
+	unsigned long bit = BIT(offset);
 	unsigned long save;
 	unsigned long ddr;
 
@@ -971,7 +971,7 @@
 {
 	struct sm501_gpio_chip *smchip = gpiochip_get_data(chip);
 	struct sm501_gpio *smgpio = smchip->ourgpio;
-	unsigned long bit = 1 << offset;
+	unsigned long bit = BIT(offset);
 	void __iomem *regs = smchip->regbase;
 	unsigned long save;
 	unsigned long val;
@@ -1720,7 +1720,12 @@
 
 static int __init sm501_base_init(void)
 {
-	platform_driver_register(&sm501_plat_driver);
+	int ret;
+
+	ret = platform_driver_register(&sm501_plat_driver);
+	if (ret < 0)
+		return ret;
+
 	return pci_register_driver(&sm501_pci_driver);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/sprd-sc27xx-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/sprd-sc27xx-spi.c
@@ -236,6 +236,12 @@
 };
 MODULE_DEVICE_TABLE(of, sprd_pmic_match);
 
+static const struct spi_device_id sprd_pmic_spi_ids[] = {
+	{ .name = "sc2731", .driver_data = (unsigned long)&sc2731_data },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, sprd_pmic_spi_ids);
+
 static struct spi_driver sprd_pmic_driver = {
 	.driver = {
 		.name = "sc27xx-pmic",
@@ -243,6 +249,7 @@
 		.pm = &sprd_pmic_pm_ops,
 	},
 	.probe = sprd_pmic_probe,
+	.id_table = sprd_pmic_spi_ids,
 };
 
 static int __init sprd_pmic_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/stmfx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/stmfx.c
@@ -330,9 +330,8 @@
 	stmfx->vdd = devm_regulator_get_optional(&client->dev, "vdd");
 	ret = PTR_ERR_OR_ZERO(stmfx->vdd);
 	if (ret) {
-		if (ret == -ENODEV)
-			stmfx->vdd = NULL;
-		else
+		stmfx->vdd = NULL;
+		if (ret != -ENODEV)
 			return dev_err_probe(&client->dev, ret, "Failed to get VDD regulator\n");
 	}
 
@@ -387,7 +386,7 @@
 
 err:
 	if (stmfx->vdd)
-		return regulator_disable(stmfx->vdd);
+		regulator_disable(stmfx->vdd);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/stmpe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/stmpe.c
@@ -1498,9 +1498,9 @@
 
 int stmpe_remove(struct stmpe *stmpe)
 {
-	if (!IS_ERR(stmpe->vio))
+	if (!IS_ERR(stmpe->vio) && regulator_is_enabled(stmpe->vio))
 		regulator_disable(stmpe->vio);
-	if (!IS_ERR(stmpe->vcc))
+	if (!IS_ERR(stmpe->vcc) && regulator_is_enabled(stmpe->vcc))
 		regulator_disable(stmpe->vcc);
 
 	__stmpe_disable(stmpe, STMPE_BLOCK_ADC);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/syscon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/syscon.c
@@ -103,6 +103,10 @@
 
 	syscon_config.name = kasprintf(GFP_KERNEL, "%pOFn@%llx", np,
 				       (u64)res.start);
+	if (!syscon_config.name) {
+		ret = -ENOMEM;
+		goto err_regmap;
+	}
 	syscon_config.reg_stride = reg_io_width;
 	syscon_config.val_bits = reg_io_width * 8;
 	syscon_config.max_register = resource_size(&res) - reg_io_width;
@@ -220,7 +224,9 @@
 		return ERR_PTR(-ENODEV);
 
 	regmap = syscon_node_to_regmap(syscon_np);
-	of_node_put(syscon_np);
+
+	if (property)
+		of_node_put(syscon_np);
 
 	return regmap;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/t7l66xb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/t7l66xb.c
@@ -397,11 +397,8 @@
 
 static int t7l66xb_remove(struct platform_device *dev)
 {
-	struct t7l66xb_platform_data *pdata = dev_get_platdata(&dev->dev);
 	struct t7l66xb *t7l66xb = platform_get_drvdata(dev);
-	int ret;
 
-	ret = pdata->disable(dev);
 	clk_disable_unprepare(t7l66xb->clk48m);
 	clk_put(t7l66xb->clk48m);
 	clk_disable_unprepare(t7l66xb->clk32k);
@@ -412,8 +409,7 @@
 	mfd_remove_devices(&dev->dev);
 	kfree(t7l66xb);
 
-	return ret;
-
+	return 0;
 }
 
 static struct platform_driver t7l66xb_platform_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/tps65010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/tps65010.c
@@ -549,17 +549,13 @@
 	 */
 	if (client->irq > 0) {
 		status = request_irq(client->irq, tps65010_irq,
-				     IRQF_TRIGGER_FALLING, DRIVER_NAME, tps);
+				     IRQF_TRIGGER_FALLING | IRQF_NO_AUTOEN,
+				     DRIVER_NAME, tps);
 		if (status < 0) {
 			dev_dbg(&client->dev, "can't get IRQ %d, err %d\n",
 					client->irq, status);
 			return status;
 		}
-		/* annoying race here, ideally we'd have an option
-		 * to claim the irq now and enable it later.
-		 * FIXME genirq IRQF_NOAUTOEN now solves that ...
-		 */
-		disable_irq(client->irq);
 		set_bit(FLAG_IRQ_ENABLE, &tps->flags);
 	} else
 		dev_warn(&client->dev, "IRQ not configured!\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/tps65910.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/tps65910.c
@@ -436,15 +436,6 @@
 
 	tps65910 = dev_get_drvdata(&tps65910_i2c_client->dev);
 
-	/*
-	 * The PWR_OFF bit needs to be set separately, before transitioning
-	 * to the OFF state. It enables the "sequential" power-off mode on
-	 * TPS65911, it's a NO-OP on TPS65910.
-	 */
-	if (regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
-			    DEVCTRL_PWR_OFF_MASK) < 0)
-		return;
-
 	regmap_update_bits(tps65910->regmap, TPS65910_DEVCTRL,
 			   DEVCTRL_DEV_OFF_MASK | DEVCTRL_DEV_ON_MASK,
 			   DEVCTRL_DEV_OFF_MASK);
@@ -504,6 +495,19 @@
 	tps65910_sleepinit(tps65910, pmic_plat_data);
 
 	if (pmic_plat_data->pm_off && !pm_power_off) {
+		/*
+		 * The PWR_OFF bit needs to be set separately, before
+		 * transitioning to the OFF state. It enables the "sequential"
+		 * power-off mode on TPS65911, it's a NO-OP on TPS65910.
+		 */
+		ret = regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
+				      DEVCTRL_PWR_OFF_MASK);
+		if (ret) {
+			dev_err(&i2c->dev, "failed to set power-off mode: %d\n",
+				ret);
+			return ret;
+		}
+
 		tps65910_i2c_client = i2c;
 		pm_power_off = tps65910_power_off;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mfd/tqmx86.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mfd/tqmx86.c
@@ -16,8 +16,8 @@
 #include <linux/platform_data/i2c-ocores.h>
 #include <linux/platform_device.h>
 
-#define TQMX86_IOBASE	0x160
-#define TQMX86_IOSIZE	0x3f
+#define TQMX86_IOBASE	0x180
+#define TQMX86_IOSIZE	0x20
 #define TQMX86_IOBASE_I2C	0x1a0
 #define TQMX86_IOSIZE_I2C	0xa
 #define TQMX86_IOBASE_WATCHDOG	0x18b
@@ -25,14 +25,14 @@
 #define TQMX86_IOBASE_GPIO	0x18d
 #define TQMX86_IOSIZE_GPIO	0x4
 
-#define TQMX86_REG_BOARD_ID	0x20
+#define TQMX86_REG_BOARD_ID	0x00
 #define TQMX86_REG_BOARD_ID_E38M	1
 #define TQMX86_REG_BOARD_ID_50UC	2
 #define TQMX86_REG_BOARD_ID_E38C	3
 #define TQMX86_REG_BOARD_ID_60EB	4
-#define TQMX86_REG_BOARD_ID_E39M	5
-#define TQMX86_REG_BOARD_ID_E39C	6
-#define TQMX86_REG_BOARD_ID_E39x	7
+#define TQMX86_REG_BOARD_ID_E39MS	5
+#define TQMX86_REG_BOARD_ID_E39C1	6
+#define TQMX86_REG_BOARD_ID_E39C2	7
 #define TQMX86_REG_BOARD_ID_70EB	8
 #define TQMX86_REG_BOARD_ID_80UC	9
 #define TQMX86_REG_BOARD_ID_110EB	11
@@ -40,18 +40,18 @@
 #define TQMX86_REG_BOARD_ID_E40S	13
 #define TQMX86_REG_BOARD_ID_E40C1	14
 #define TQMX86_REG_BOARD_ID_E40C2	15
-#define TQMX86_REG_BOARD_REV	0x21
-#define TQMX86_REG_IO_EXT_INT	0x26
+#define TQMX86_REG_BOARD_REV	0x01
+#define TQMX86_REG_IO_EXT_INT	0x06
 #define TQMX86_REG_IO_EXT_INT_NONE		0
 #define TQMX86_REG_IO_EXT_INT_7			1
 #define TQMX86_REG_IO_EXT_INT_9			2
 #define TQMX86_REG_IO_EXT_INT_12		3
 #define TQMX86_REG_IO_EXT_INT_MASK		0x3
 #define TQMX86_REG_IO_EXT_INT_GPIO_SHIFT	4
+#define TQMX86_REG_SAUC		0x17
 
-#define TQMX86_REG_I2C_DETECT	0x47
+#define TQMX86_REG_I2C_DETECT	0x1a7
 #define TQMX86_REG_I2C_DETECT_SOFT		0xa5
-#define TQMX86_REG_I2C_INT_EN	0x49
 
 static uint gpio_irq;
 module_param(gpio_irq, uint, 0);
@@ -111,7 +111,7 @@
 	},
 };
 
-static const char *tqmx86_board_id_to_name(u8 board_id)
+static const char *tqmx86_board_id_to_name(u8 board_id, u8 sauc)
 {
 	switch (board_id) {
 	case TQMX86_REG_BOARD_ID_E38M:
@@ -122,12 +122,12 @@
 		return "TQMxE38C";
 	case TQMX86_REG_BOARD_ID_60EB:
 		return "TQMx60EB";
-	case TQMX86_REG_BOARD_ID_E39M:
-		return "TQMxE39M";
-	case TQMX86_REG_BOARD_ID_E39C:
-		return "TQMxE39C";
-	case TQMX86_REG_BOARD_ID_E39x:
-		return "TQMxE39x";
+	case TQMX86_REG_BOARD_ID_E39MS:
+		return (sauc == 0xff) ? "TQMxE39M" : "TQMxE39S";
+	case TQMX86_REG_BOARD_ID_E39C1:
+		return "TQMxE39C1";
+	case TQMX86_REG_BOARD_ID_E39C2:
+		return "TQMxE39C2";
 	case TQMX86_REG_BOARD_ID_70EB:
 		return "TQMx70EB";
 	case TQMX86_REG_BOARD_ID_80UC:
@@ -160,9 +160,9 @@
 	case TQMX86_REG_BOARD_ID_E40C1:
 	case TQMX86_REG_BOARD_ID_E40C2:
 		return 24000;
-	case TQMX86_REG_BOARD_ID_E39M:
-	case TQMX86_REG_BOARD_ID_E39C:
-	case TQMX86_REG_BOARD_ID_E39x:
+	case TQMX86_REG_BOARD_ID_E39MS:
+	case TQMX86_REG_BOARD_ID_E39C1:
+	case TQMX86_REG_BOARD_ID_E39C2:
 		return 25000;
 	case TQMX86_REG_BOARD_ID_E38M:
 	case TQMX86_REG_BOARD_ID_E38C:
@@ -176,7 +176,7 @@
 
 static int tqmx86_probe(struct platform_device *pdev)
 {
-	u8 board_id, rev, i2c_det, io_ext_int_val;
+	u8 board_id, sauc, rev, i2c_det, io_ext_int_val;
 	struct device *dev = &pdev->dev;
 	u8 gpio_irq_cfg, readback;
 	const char *board_name;
@@ -206,14 +206,20 @@
 		return -ENOMEM;
 
 	board_id = ioread8(io_base + TQMX86_REG_BOARD_ID);
-	board_name = tqmx86_board_id_to_name(board_id);
+	sauc = ioread8(io_base + TQMX86_REG_SAUC);
+	board_name = tqmx86_board_id_to_name(board_id, sauc);
 	rev = ioread8(io_base + TQMX86_REG_BOARD_REV);
 
 	dev_info(dev,
 		 "Found %s - Board ID %d, PCB Revision %d, PLD Revision %d\n",
 		 board_name, board_id, rev >> 4, rev & 0xf);
 
-	i2c_det = ioread8(io_base + TQMX86_REG_I2C_DETECT);
+	/*
+	 * The I2C_DETECT register is in the range assigned to the I2C driver
+	 * later, so we don't extend TQMX86_IOSIZE. Use inb() for this one-off
+	 * access instead of ioport_map + unmap.
+	 */
+	i2c_det = inb(TQMX86_REG_I2C_DETECT);
 
 	if (gpio_irq_cfg) {
 		io_ext_int_val =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/Kconfig
@@ -456,6 +456,55 @@
 
 	  If unsure, say N.
 
+config XILINX_DPU
+	tristate "Xilinx Deep learning Processing Unit (DPU) Driver"
+	depends on HAS_IOMEM && COMMON_CLK
+	depends on ARCH_ZYNQMP || MICROBLAZE
+	help
+	  This option enables support for the Xilinx DPUCZDX8G (Deep learning
+	  Processing Unit) Vivado flow driver.
+	  It is a configurable computation engine dedicated for convolutional
+	  neural networks. The degree of parallelism utilized in the engine
+	  is a design parameter and application. It includes a set of optimized
+	  instructions, and supports most convolutional neural networks.
+
+	  If unsure, say N.
+
+config XILINX_FLEX_PM
+	tristate "Xilinx Flexnoc Performance Monitor"
+	help
+	  This option enables support for the Xilinx Flex Noc Performance Monitor driver.
+	  It monitors the read and write transactions. It has counters for the LPD and
+	  FPD domains.
+
+	  If unsure, say N
+
+config XILINX_TRAFGEN
+	tristate "Xilinx Traffic Generator"
+	help
+	  This option enables support for the Xilinx Traffic Generator driver.
+	  It is designed to generate AXI4 traffic which can be used to stress
+	  different modules/interconnect connected in the system. Different
+	  configurable options which are provided through sysfs entries allow
+	  allow the user to generate a wide variety of traffic based on their
+	  their requirements.
+
+	  If unsure, say N
+
+config XILINX_AIE
+	tristate "Xilinx AI engine"
+	depends on ARM64 || COMPILE_TEST
+	depends on ZYNQMP_FIRMWARE
+	select FPGA_BRIDGE
+	help
+	  This option enables support for the Xilinx AI engine driver.
+	  One Xilinx AI engine device can have multiple partitions (groups of
+	  AI engine tiles). Xilinx AI engine device driver instance manages
+	  AI engine partitions. User application access its partitions through
+	  AI engine partition instance file operations.
+
+	  If unsure, say N
+
 config MISC_RTSX
 	tristate
 	default MISC_RTSX_PCI || MISC_RTSX_USB
@@ -470,6 +519,27 @@
 	  switching between the dual-role USB-C port and the USB-A host ports
 	  using only one USB controller.
 
+config TMR_MANAGER
+	bool "Select TMR Manager"
+	depends on MICROBLAZE && MB_MANAGER
+	help
+	  This option enables the driver developed for TMR Manager. The Triple
+	  Modular Redundancy(TMR) manager provides support for fault detection
+	  via sysfs interface.
+
+	  Say N here unless you know what you are doing.
+
+config TMR_INJECT
+	bool "Select TMR Inject"
+	depends on TMR_MANAGER
+	help
+	  This option enables the driver developed for TMR Inject.
+	  The Triple Modular Redundancy(TMR) Inject provides
+	  fault injection.
+
+	  Say N here unless you know what you are doing.
+
+source "drivers/misc/jesd204b/Kconfig"
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
@@ -477,6 +547,7 @@
 source "drivers/misc/lis3lv02d/Kconfig"
 source "drivers/misc/altera-stapl/Kconfig"
 source "drivers/misc/mei/Kconfig"
+source "drivers/misc/ivsc/Kconfig"
 source "drivers/misc/vmw_vmci/Kconfig"
 source "drivers/misc/genwqe/Kconfig"
 source "drivers/misc/echo/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/Makefile
@@ -41,6 +41,7 @@
 obj-y				+= lis3lv02d/
 obj-$(CONFIG_ALTERA_STAPL)	+=altera-stapl/
 obj-$(CONFIG_INTEL_MEI)		+= mei/
+obj-$(CONFIG_INTEL_VSC)		+= ivsc/
 obj-$(CONFIG_VMWARE_VMCI)	+= vmw_vmci/
 obj-$(CONFIG_LATTICE_ECP3_CONFIG)	+= lattice-ecp3-config.o
 obj-$(CONFIG_SRAM)		+= sram.o
@@ -57,5 +58,12 @@
 obj-$(CONFIG_HABANA_AI)		+= habanalabs/
 obj-$(CONFIG_UACCE)		+= uacce/
 obj-$(CONFIG_XILINX_SDFEC)	+= xilinx_sdfec.o
+obj-$(CONFIG_XILINX_DPU)	+= xlnx_dpu.o
 obj-$(CONFIG_HISI_HIKEY_USB)	+= hisi_hikey_usb.o
+obj-$(CONFIG_XILINX_FLEX_PM)	+= xilinx_flex_pm.o
+obj-$(CONFIG_XILINX_TRAFGEN)	+= xilinx_trafgen.o
+obj-$(CONFIG_XILINX_JESD204B)	+= jesd204b/
+obj-$(CONFIG_XILINX_AIE)	+= xilinx-ai-engine/
 obj-$(CONFIG_HI6421V600_IRQ)	+= hi6421v600-irq.o
+obj-$(CONFIG_TMR_MANAGER)	+= xilinx_tmr_manager.o
+obj-$(CONFIG_TMR_INJECT)	+= xilinx_tmr_inject.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/apds990x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/apds990x.c
@@ -1148,7 +1148,7 @@
 		err = chip->pdata->setup_resources();
 		if (err) {
 			err = -EINVAL;
-			goto fail3;
+			goto fail4;
 		}
 	}
 
@@ -1156,7 +1156,7 @@
 				apds990x_attribute_group);
 	if (err < 0) {
 		dev_err(&chip->client->dev, "Sysfs registration failed\n");
-		goto fail4;
+		goto fail5;
 	}
 
 	err = request_threaded_irq(client->irq, NULL,
@@ -1167,15 +1167,17 @@
 	if (err) {
 		dev_err(&client->dev, "could not get IRQ %d\n",
 			client->irq);
-		goto fail5;
+		goto fail6;
 	}
 	return err;
-fail5:
+fail6:
 	sysfs_remove_group(&chip->client->dev.kobj,
 			&apds990x_attribute_group[0]);
-fail4:
+fail5:
 	if (chip->pdata && chip->pdata->release_resources)
 		chip->pdata->release_resources();
+fail4:
+	pm_runtime_disable(&client->dev);
 fail3:
 	regulator_bulk_disable(ARRAY_SIZE(chip->regs), chip->regs);
 fail2:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/atmel-ssc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/atmel-ssc.c
@@ -232,9 +232,9 @@
 	clk_disable_unprepare(ssc->clk);
 
 	ssc->irq = platform_get_irq(pdev, 0);
-	if (!ssc->irq) {
+	if (ssc->irq < 0) {
 		dev_dbg(&pdev->dev, "could not get irq\n");
-		return -ENXIO;
+		return ssc->irq;
 	}
 
 	mutex_lock(&user_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/alcor_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/alcor_pci.c
@@ -266,7 +266,7 @@
 	if (!priv)
 		return -ENOMEM;
 
-	ret = ida_simple_get(&alcor_pci_idr, 0, 0, GFP_KERNEL);
+	ret = ida_alloc(&alcor_pci_idr, GFP_KERNEL);
 	if (ret < 0)
 		return ret;
 	priv->id = ret;
@@ -280,7 +280,8 @@
 	ret = pci_request_regions(pdev, DRV_NAME_ALCOR_PCI);
 	if (ret) {
 		dev_err(&pdev->dev, "Cannot request region\n");
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto error_free_ida;
 	}
 
 	if (!(pci_resource_flags(pdev, bar) & IORESOURCE_MEM)) {
@@ -324,6 +325,8 @@
 
 error_release_regions:
 	pci_release_regions(pdev);
+error_free_ida:
+	ida_free(&alcor_pci_idr, priv->id);
 	return ret;
 }
 
@@ -337,7 +340,7 @@
 
 	mfd_remove_devices(&pdev->dev);
 
-	ida_simple_remove(&alcor_pci_idr, priv->id);
+	ida_free(&alcor_pci_idr, priv->id);
 
 	pci_release_regions(pdev);
 	pci_set_drvdata(pdev, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rtl8411.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rtl8411.c
@@ -76,7 +76,7 @@
 		map_sd_drive(rtl8411b_reg_to_sd30_drive_sel_3v3(reg));
 }
 
-static void rtl8411_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
+static void rtl8411_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
 	rtsx_pci_write_register(pcr, FPDCTL, 0x07, 0x07);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5209.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5209.c
@@ -47,7 +47,7 @@
 	}
 }
 
-static void rts5209_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
+static void rts5209_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
 	rtsx_pci_write_register(pcr, FPDCTL, 0x07, 0x07);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5227.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5227.c
@@ -72,6 +72,8 @@
 
 	pci_read_config_dword(pdev, PCR_SETTING_REG2, &reg);
 	pcr_dbg(pcr, "Cfg 0x%x: 0x%x\n", PCR_SETTING_REG2, reg);
+	if (CHK_PCI_PID(pcr, 0x522A))
+		pcr->rtd3_en = rtsx_reg_to_rtd3(reg);
 	if (rtsx_check_mmc_support(reg))
 		pcr->extra_caps |= EXTRA_CAPS_NO_MMC;
 	pcr->sd30_drive_sel_3v3 = rtsx_reg_to_sd30_drive_sel_3v3(reg);
@@ -81,63 +83,20 @@
 
 static void rts5227_init_from_cfg(struct rtsx_pcr *pcr)
 {
-	struct pci_dev *pdev = pcr->pci;
-	int l1ss;
-	u32 lval;
 	struct rtsx_cr_option *option = &pcr->option;
 
-	l1ss = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
-	if (!l1ss)
-		return;
-
-	pci_read_config_dword(pdev, l1ss + PCI_L1SS_CTL1, &lval);
-
 	if (CHK_PCI_PID(pcr, 0x522A)) {
-		if (0 == (lval & 0x0F))
-			rtsx_pci_enable_oobs_polling(pcr);
-		else
+		if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
+				| PM_L1_1_EN | PM_L1_2_EN))
 			rtsx_pci_disable_oobs_polling(pcr);
+		else
+			rtsx_pci_enable_oobs_polling(pcr);
 	}
 
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
-		rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
-	else
-		rtsx_clear_dev_flag(pcr, ASPM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
-		rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
-	else
-		rtsx_clear_dev_flag(pcr, ASPM_L1_2_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
-		rtsx_set_dev_flag(pcr, PM_L1_1_EN);
-	else
-		rtsx_clear_dev_flag(pcr, PM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
-		rtsx_set_dev_flag(pcr, PM_L1_2_EN);
-	else
-		rtsx_clear_dev_flag(pcr, PM_L1_2_EN);
-
 	if (option->ltr_en) {
-		u16 val;
-
-		pcie_capability_read_word(pcr->pci, PCI_EXP_DEVCTL2, &val);
-		if (val & PCI_EXP_DEVCTL2_LTR_EN) {
-			option->ltr_enabled = true;
-			option->ltr_active = true;
+		if (option->ltr_enabled)
 			rtsx_set_ltr_latency(pcr, option->ltr_active_latency);
-		} else {
-			option->ltr_enabled = false;
-		}
 	}
-
-	if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
-				| PM_L1_1_EN | PM_L1_2_EN))
-		option->force_clkreq_0 = false;
-	else
-		option->force_clkreq_0 = true;
-
 }
 
 static int rts5227_extra_init_hw(struct rtsx_pcr *pcr)
@@ -171,6 +130,28 @@
 	else
 		rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PETXCFG, 0x30, 0x00);
 
+	if (CHK_PCI_PID(pcr, 0x522A))
+		rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, RTS522A_AUTOLOAD_CFG1,
+			CD_RESUME_EN_MASK, CD_RESUME_EN_MASK);
+
+	if (pcr->rtd3_en) {
+		if (CHK_PCI_PID(pcr, 0x522A)) {
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, RTS522A_PM_CTRL3, 0x01, 0x01);
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, RTS522A_PME_FORCE_CTL, 0x30, 0x30);
+		} else {
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PM_CTRL3, 0x01, 0x01);
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PME_FORCE_CTL, 0xFF, 0x33);
+		}
+	} else {
+		if (CHK_PCI_PID(pcr, 0x522A)) {
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, RTS522A_PM_CTRL3, 0x01, 0x00);
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, RTS522A_PME_FORCE_CTL, 0x30, 0x20);
+		} else {
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PME_FORCE_CTL, 0xFF, 0x30);
+			rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PM_CTRL3, 0x01, 0x00);
+		}
+	}
+
 	if (option->force_clkreq_0)
 		rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, PETXCFG,
 				FORCE_CLKREQ_DELINK_MASK, FORCE_CLKREQ_LOW);
@@ -438,6 +419,28 @@
 	return rtsx_pci_send_cmd(pcr, 100);
 }
 
+static void rts522a_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
+{
+	/* Set relink_time to 0 */
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, MASK_8_BIT_DEF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 2, MASK_8_BIT_DEF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 3,
+				RELINK_TIME_MASK, 0);
+
+	rtsx_pci_write_register(pcr, RTS522A_PM_CTRL3,
+			D3_DELINK_MODE_EN, D3_DELINK_MODE_EN);
+
+	if (!runtime) {
+		rtsx_pci_write_register(pcr, RTS522A_AUTOLOAD_CFG1,
+				CD_RESUME_EN_MASK, 0);
+		rtsx_pci_write_register(pcr, RTS522A_PM_CTRL3, 0x01, 0x00);
+		rtsx_pci_write_register(pcr, RTS522A_PME_FORCE_CTL, 0x30, 0x20);
+	}
+
+	rtsx_pci_write_register(pcr, FPDCTL, ALL_POWER_DOWN, ALL_POWER_DOWN);
+}
+
+
 static void rts522a_set_l1off_cfg_sub_d0(struct rtsx_pcr *pcr, int active)
 {
 	struct rtsx_cr_option *option = &pcr->option;
@@ -473,6 +476,7 @@
 	.card_power_on = rts5227_card_power_on,
 	.card_power_off = rts5227_card_power_off,
 	.switch_output_voltage = rts522a_switch_output_voltage,
+	.force_power_down = rts522a_force_power_down,
 	.cd_deglitch = NULL,
 	.conv_clk_and_div_n = NULL,
 	.set_l1off_cfg_sub_d0 = rts522a_set_l1off_cfg_sub_d0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5228.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5228.c
@@ -91,7 +91,7 @@
 	return rtsx_pci_write_phy_register(pcr, 0x07, 0x8F40);
 }
 
-static void rts5228_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
+static void rts5228_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
 	/* Set relink_time to 0 */
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, MASK_8_BIT_DEF, 0);
@@ -102,6 +102,14 @@
 	rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3,
 			D3_DELINK_MODE_EN, D3_DELINK_MODE_EN);
 
+	if (!runtime) {
+		rtsx_pci_write_register(pcr, RTS5228_AUTOLOAD_CFG1,
+				CD_RESUME_EN_MASK, 0);
+		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x01, 0x00);
+		rtsx_pci_write_register(pcr, RTS5228_REG_PME_FORCE_CTL,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE, FORCE_PM_CONTROL);
+	}
+
 	rtsx_pci_write_register(pcr, FPDCTL,
 		SSC_POWER_DOWN, SSC_POWER_DOWN);
 }
@@ -378,61 +386,20 @@
 
 static void rts5228_init_from_cfg(struct rtsx_pcr *pcr)
 {
-	struct pci_dev *pdev = pcr->pci;
-	int l1ss;
-	u32 lval;
 	struct rtsx_cr_option *option = &pcr->option;
 
-	l1ss = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
-	if (!l1ss)
-		return;
-
-	pci_read_config_dword(pdev, l1ss + PCI_L1SS_CTL1, &lval);
-
-	if (0 == (lval & 0x0F))
-		rtsx_pci_enable_oobs_polling(pcr);
-	else
+	if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
+				| PM_L1_1_EN | PM_L1_2_EN))
 		rtsx_pci_disable_oobs_polling(pcr);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
-		rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
-	else
-		rtsx_clear_dev_flag(pcr, ASPM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
-		rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
-	else
-		rtsx_clear_dev_flag(pcr, ASPM_L1_2_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
-		rtsx_set_dev_flag(pcr, PM_L1_1_EN);
-	else
-		rtsx_clear_dev_flag(pcr, PM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
-		rtsx_set_dev_flag(pcr, PM_L1_2_EN);
 	else
-		rtsx_clear_dev_flag(pcr, PM_L1_2_EN);
+		rtsx_pci_enable_oobs_polling(pcr);
 
 	rtsx_pci_write_register(pcr, ASPM_FORCE_CTL, 0xFF, 0);
-	if (option->ltr_en) {
-		u16 val;
 
-		pcie_capability_read_word(pcr->pci, PCI_EXP_DEVCTL2, &val);
-		if (val & PCI_EXP_DEVCTL2_LTR_EN) {
-			option->ltr_enabled = true;
-			option->ltr_active = true;
+	if (option->ltr_en) {
+		if (option->ltr_enabled)
 			rtsx_set_ltr_latency(pcr, option->ltr_active_latency);
-		} else {
-			option->ltr_enabled = false;
-		}
 	}
-
-	if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
-				| PM_L1_1_EN | PM_L1_2_EN))
-		option->force_clkreq_0 = false;
-	else
-		option->force_clkreq_0 = true;
 }
 
 static int rts5228_extra_init_hw(struct rtsx_pcr *pcr)
@@ -480,9 +447,18 @@
 				 FORCE_CLKREQ_DELINK_MASK, FORCE_CLKREQ_HIGH);
 
 	rtsx_pci_write_register(pcr, PWD_SUSPEND_EN, 0xFF, 0xFB);
-	rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x10, 0x00);
+
+	if (pcr->rtd3_en) {
+		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x01, 0x01);
 	rtsx_pci_write_register(pcr, RTS5228_REG_PME_FORCE_CTL,
-			FORCE_PM_CONTROL | FORCE_PM_VALUE, FORCE_PM_CONTROL);
+				FORCE_PM_CONTROL | FORCE_PM_VALUE,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE);
+	} else {
+		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x01, 0x00);
+		rtsx_pci_write_register(pcr, RTS5228_REG_PME_FORCE_CTL,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE, FORCE_PM_CONTROL);
+	}
+	rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, D3_DELINK_MODE_EN, 0x00);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5229.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5229.c
@@ -44,7 +44,7 @@
 		map_sd_drive(rtsx_reg_to_sd30_drive_sel_3v3(reg));
 }
 
-static void rts5229_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
+static void rts5229_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
 	rtsx_pci_write_register(pcr, FPDCTL, 0x03, 0x03);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5249.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5249.c
@@ -74,7 +74,8 @@
 	pci_read_config_dword(pdev, PCR_SETTING_REG2, &reg);
 	pcr_dbg(pcr, "Cfg 0x%x: 0x%x\n", PCR_SETTING_REG2, reg);
 
-	pcr->rtd3_en = rtsx_reg_to_rtd3_uhsii(reg);
+	if (CHK_PCI_PID(pcr, PID_524A) || CHK_PCI_PID(pcr, PID_525A))
+		pcr->rtd3_en = rtsx_reg_to_rtd3_uhsii(reg);
 
 	if (rtsx_check_mmc_support(reg))
 		pcr->extra_caps |= EXTRA_CAPS_NO_MMC;
@@ -85,62 +86,41 @@
 
 static void rts5249_init_from_cfg(struct rtsx_pcr *pcr)
 {
-	struct pci_dev *pdev = pcr->pci;
-	int l1ss;
 	struct rtsx_cr_option *option = &(pcr->option);
-	u32 lval;
-
-	l1ss = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
-	if (!l1ss)
-		return;
-
-	pci_read_config_dword(pdev, l1ss + PCI_L1SS_CTL1, &lval);
 
 	if (CHK_PCI_PID(pcr, PID_524A) || CHK_PCI_PID(pcr, PID_525A)) {
-		if (0 == (lval & 0x0F))
-			rtsx_pci_enable_oobs_polling(pcr);
-		else
+		if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
+				| PM_L1_1_EN | PM_L1_2_EN))
 			rtsx_pci_disable_oobs_polling(pcr);
+		else
+			rtsx_pci_enable_oobs_polling(pcr);
 	}
 
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
-		rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
-		rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
-		rtsx_set_dev_flag(pcr, PM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
-		rtsx_set_dev_flag(pcr, PM_L1_2_EN);
-
 	if (option->ltr_en) {
-		u16 val;
-
-		pcie_capability_read_word(pdev, PCI_EXP_DEVCTL2, &val);
-		if (val & PCI_EXP_DEVCTL2_LTR_EN) {
-			option->ltr_enabled = true;
-			option->ltr_active = true;
+		if (option->ltr_enabled)
 			rtsx_set_ltr_latency(pcr, option->ltr_active_latency);
-		} else {
-			option->ltr_enabled = false;
-		}
 	}
 }
 
-static int rts5249_init_from_hw(struct rtsx_pcr *pcr)
+static void rts52xa_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
-	struct rtsx_cr_option *option = &(pcr->option);
+	/* Set relink_time to 0 */
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, MASK_8_BIT_DEF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 2, MASK_8_BIT_DEF, 0);
+	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 3,
+				RELINK_TIME_MASK, 0);
 
-	if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
-				| PM_L1_1_EN | PM_L1_2_EN))
-		option->force_clkreq_0 = false;
-	else
-		option->force_clkreq_0 = true;
+	rtsx_pci_write_register(pcr, RTS524A_PM_CTRL3,
+			D3_DELINK_MODE_EN, D3_DELINK_MODE_EN);
 
-	return 0;
+	if (!runtime) {
+		rtsx_pci_write_register(pcr, RTS524A_AUTOLOAD_CFG1,
+				CD_RESUME_EN_MASK, 0);
+		rtsx_pci_write_register(pcr, RTS524A_PM_CTRL3, 0x01, 0x00);
+		rtsx_pci_write_register(pcr, RTS524A_PME_FORCE_CTL, 0x30, 0x20);
+	}
+
+	rtsx_pci_write_register(pcr, FPDCTL, ALL_POWER_DOWN, ALL_POWER_DOWN);
 }
 
 static void rts52xa_save_content_from_efuse(struct rtsx_pcr *pcr)
@@ -254,7 +234,6 @@
 	struct rtsx_cr_option *option = &(pcr->option);
 
 	rts5249_init_from_cfg(pcr);
-	rts5249_init_from_hw(pcr);
 
 	rtsx_pci_init_cmd(pcr);
 
@@ -281,8 +260,11 @@
 
 	rtsx_pci_send_cmd(pcr, CMD_TIMEOUT_DEF);
 
-	if (CHK_PCI_PID(pcr, PID_524A) || CHK_PCI_PID(pcr, PID_525A))
+	if (CHK_PCI_PID(pcr, PID_524A) || CHK_PCI_PID(pcr, PID_525A)) {
 		rtsx_pci_write_register(pcr, REG_VREF, PWD_SUSPND_EN, PWD_SUSPND_EN);
+		rtsx_pci_write_register(pcr, RTS524A_AUTOLOAD_CFG1,
+			CD_RESUME_EN_MASK, CD_RESUME_EN_MASK);
+	}
 
 	if (pcr->rtd3_en) {
 		if (CHK_PCI_PID(pcr, PID_524A) || CHK_PCI_PID(pcr, PID_525A)) {
@@ -724,6 +706,7 @@
 	.card_power_on = rtsx_base_card_power_on,
 	.card_power_off = rtsx_base_card_power_off,
 	.switch_output_voltage = rtsx_base_switch_output_voltage,
+	.force_power_down = rts52xa_force_power_down,
 	.set_l1off_cfg_sub_d0 = rts5250_set_l1off_cfg_sub_d0,
 };
 
@@ -841,6 +824,7 @@
 	.card_power_on = rts525a_card_power_on,
 	.card_power_off = rtsx_base_card_power_off,
 	.switch_output_voltage = rts525a_switch_output_voltage,
+	.force_power_down = rts52xa_force_power_down,
 	.set_l1off_cfg_sub_d0 = rts5250_set_l1off_cfg_sub_d0,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5260.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5260.c
@@ -480,49 +480,14 @@
 
 static void rts5260_init_from_cfg(struct rtsx_pcr *pcr)
 {
-	struct pci_dev *pdev = pcr->pci;
-	int l1ss;
 	struct rtsx_cr_option *option = &pcr->option;
-	u32 lval;
-
-	l1ss = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
-	if (!l1ss)
-		return;
-
-	pci_read_config_dword(pdev, l1ss + PCI_L1SS_CTL1, &lval);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
-		rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
-		rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
-		rtsx_set_dev_flag(pcr, PM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
-		rtsx_set_dev_flag(pcr, PM_L1_2_EN);
 
 	rts5260_pwr_saving_setting(pcr);
 
 	if (option->ltr_en) {
-		u16 val;
-
-		pcie_capability_read_word(pdev, PCI_EXP_DEVCTL2, &val);
-		if (val & PCI_EXP_DEVCTL2_LTR_EN) {
-			option->ltr_enabled = true;
-			option->ltr_active = true;
+		if (option->ltr_enabled)
 			rtsx_set_ltr_latency(pcr, option->ltr_active_latency);
-		} else {
-			option->ltr_enabled = false;
-		}
 	}
-
-	if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
-				| PM_L1_1_EN | PM_L1_2_EN))
-		option->force_clkreq_0 = false;
-	else
-		option->force_clkreq_0 = true;
 }
 
 static int rts5260_extra_init_hw(struct rtsx_pcr *pcr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rts5261.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rts5261.c
@@ -91,7 +91,7 @@
 	pcr->sd30_drive_sel_3v3 = rts5261_reg_to_sd30_drive_sel_3v3(reg);
 }
 
-static void rts5261_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
+static void rts5261_force_power_down(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
 	/* Set relink_time to 0 */
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, MASK_8_BIT_DEF, 0);
@@ -103,6 +103,24 @@
 		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3,
 					D3_DELINK_MODE_EN, D3_DELINK_MODE_EN);
 
+	if (!runtime) {
+		rtsx_pci_write_register(pcr, RTS5261_AUTOLOAD_CFG1,
+				CD_RESUME_EN_MASK, 0);
+		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x01, 0x00);
+		rtsx_pci_write_register(pcr, RTS5261_REG_PME_FORCE_CTL,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE, FORCE_PM_CONTROL);
+
+	} else {
+		rtsx_pci_write_register(pcr, RTS5261_REG_PME_FORCE_CTL,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE, 0);
+
+		rtsx_pci_write_register(pcr, RTS5261_FW_CTL,
+				RTS5261_INFORM_RTD3_COLD, RTS5261_INFORM_RTD3_COLD);
+		rtsx_pci_write_register(pcr, RTS5261_AUTOLOAD_CFG4,
+				RTS5261_FORCE_PRSNT_LOW, RTS5261_FORCE_PRSNT_LOW);
+
+	}
+
 	rtsx_pci_write_register(pcr, RTS5261_REG_FPDCTL,
 		SSC_POWER_DOWN, SSC_POWER_DOWN);
 }
@@ -424,56 +442,12 @@
 
 static void rts5261_init_from_cfg(struct rtsx_pcr *pcr)
 {
-	struct pci_dev *pdev = pcr->pci;
-	int l1ss;
-	u32 lval;
 	struct rtsx_cr_option *option = &pcr->option;
 
-	l1ss = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
-	if (!l1ss)
-		return;
-
-	pci_read_config_dword(pdev, l1ss + PCI_L1SS_CTL1, &lval);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
-		rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
-	else
-		rtsx_clear_dev_flag(pcr, ASPM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
-		rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
-	else
-		rtsx_clear_dev_flag(pcr, ASPM_L1_2_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
-		rtsx_set_dev_flag(pcr, PM_L1_1_EN);
-	else
-		rtsx_clear_dev_flag(pcr, PM_L1_1_EN);
-
-	if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
-		rtsx_set_dev_flag(pcr, PM_L1_2_EN);
-	else
-		rtsx_clear_dev_flag(pcr, PM_L1_2_EN);
-
-	rtsx_pci_write_register(pcr, ASPM_FORCE_CTL, 0xFF, 0);
 	if (option->ltr_en) {
-		u16 val;
-
-		pcie_capability_read_word(pdev, PCI_EXP_DEVCTL2, &val);
-		if (val & PCI_EXP_DEVCTL2_LTR_EN) {
-			option->ltr_enabled = true;
-			option->ltr_active = true;
+		if (option->ltr_enabled)
 			rtsx_set_ltr_latency(pcr, option->ltr_active_latency);
-		} else {
-			option->ltr_enabled = false;
-		}
 	}
-
-	if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
-				| PM_L1_1_EN | PM_L1_2_EN))
-		option->force_clkreq_0 = false;
-	else
-		option->force_clkreq_0 = true;
 }
 
 static int rts5261_extra_init_hw(struct rtsx_pcr *pcr)
@@ -536,9 +510,18 @@
 				 FORCE_CLKREQ_DELINK_MASK, FORCE_CLKREQ_HIGH);
 
 	rtsx_pci_write_register(pcr, PWD_SUSPEND_EN, 0xFF, 0xFB);
-	rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x10, 0x00);
-	rtsx_pci_write_register(pcr, RTS5261_REG_PME_FORCE_CTL,
-			FORCE_PM_CONTROL | FORCE_PM_VALUE, FORCE_PM_CONTROL);
+
+	if (pcr->rtd3_en) {
+		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x01, 0x01);
+		rtsx_pci_write_register(pcr, RTS5261_REG_PME_FORCE_CTL,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE);
+	} else {
+		rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, 0x01, 0x00);
+		rtsx_pci_write_register(pcr, RTS5261_REG_PME_FORCE_CTL,
+				FORCE_PM_CONTROL | FORCE_PM_VALUE, FORCE_PM_CONTROL);
+	}
+	rtsx_pci_write_register(pcr, pcr->reg_pm_ctrl3, D3_DELINK_MODE_EN, 0x00);
 
 	/* Clear Enter RTD3_cold Information*/
 	rtsx_pci_write_register(pcr, RTS5261_FW_CTL,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rtsx_pcr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rtsx_pcr.c
@@ -152,20 +152,12 @@
 	if (pcr->remove_pci)
 		return;
 
-	if (pcr->rtd3_en)
-		if (pcr->is_runtime_suspended) {
-			pm_runtime_get(&(pcr->pci->dev));
-			pcr->is_runtime_suspended = false;
-		}
-
 	if (pcr->state != PDEV_STAT_RUN) {
 		pcr->state = PDEV_STAT_RUN;
 		if (pcr->ops->enable_auto_blink)
 			pcr->ops->enable_auto_blink(pcr);
 		rtsx_pm_full_on(pcr);
 	}
-
-	mod_delayed_work(system_wq, &pcr->idle_work, msecs_to_jiffies(200));
 }
 EXPORT_SYMBOL_GPL(rtsx_pci_start_run);
 
@@ -1062,73 +1054,7 @@
 	return 0;
 }
 
-static void rtsx_enable_aspm(struct rtsx_pcr *pcr)
-{
-	if (pcr->ops->set_aspm)
-		pcr->ops->set_aspm(pcr, true);
-	else
-		rtsx_comm_set_aspm(pcr, true);
-}
-
-static void rtsx_comm_pm_power_saving(struct rtsx_pcr *pcr)
-{
-	struct rtsx_cr_option *option = &pcr->option;
-
-	if (option->ltr_enabled) {
-		u32 latency = option->ltr_l1off_latency;
-
-		if (rtsx_check_dev_flag(pcr, L1_SNOOZE_TEST_EN))
-			mdelay(option->l1_snooze_delay);
-
-		rtsx_set_ltr_latency(pcr, latency);
-	}
-
-	if (rtsx_check_dev_flag(pcr, LTR_L1SS_PWR_GATE_EN))
-		rtsx_set_l1off_sub_cfg_d0(pcr, 0);
-
-	rtsx_enable_aspm(pcr);
-}
-
-static void rtsx_pm_power_saving(struct rtsx_pcr *pcr)
-{
-	rtsx_comm_pm_power_saving(pcr);
-}
-
-static void rtsx_pci_rtd3_work(struct work_struct *work)
-{
-	struct delayed_work *dwork = to_delayed_work(work);
-	struct rtsx_pcr *pcr = container_of(dwork, struct rtsx_pcr, rtd3_work);
-
-	pcr_dbg(pcr, "--> %s\n", __func__);
-	if (!pcr->is_runtime_suspended)
-		pm_runtime_put(&(pcr->pci->dev));
-}
-
-static void rtsx_pci_idle_work(struct work_struct *work)
-{
-	struct delayed_work *dwork = to_delayed_work(work);
-	struct rtsx_pcr *pcr = container_of(dwork, struct rtsx_pcr, idle_work);
-
-	pcr_dbg(pcr, "--> %s\n", __func__);
-
-	mutex_lock(&pcr->pcr_mutex);
-
-	pcr->state = PDEV_STAT_IDLE;
-
-	if (pcr->ops->disable_auto_blink)
-		pcr->ops->disable_auto_blink(pcr);
-	if (pcr->ops->turn_off_led)
-		pcr->ops->turn_off_led(pcr);
-
-	rtsx_pm_power_saving(pcr);
-
-	mutex_unlock(&pcr->pcr_mutex);
-
-	if (pcr->rtd3_en)
-		mod_delayed_work(system_wq, &pcr->rtd3_work, msecs_to_jiffies(10000));
-}
-
-static void rtsx_base_force_power_down(struct rtsx_pcr *pcr, u8 pm_state)
+static void rtsx_base_force_power_down(struct rtsx_pcr *pcr)
 {
 	/* Set relink_time to 0 */
 	rtsx_pci_write_register(pcr, AUTOLOAD_CFG_BASE + 1, MASK_8_BIT_DEF, 0);
@@ -1142,7 +1068,7 @@
 	rtsx_pci_write_register(pcr, FPDCTL, ALL_POWER_DOWN, ALL_POWER_DOWN);
 }
 
-static void __maybe_unused rtsx_pci_power_off(struct rtsx_pcr *pcr, u8 pm_state)
+static void __maybe_unused rtsx_pci_power_off(struct rtsx_pcr *pcr, u8 pm_state, bool runtime)
 {
 	if (pcr->ops->turn_off_led)
 		pcr->ops->turn_off_led(pcr);
@@ -1154,9 +1080,9 @@
 	rtsx_pci_write_register(pcr, HOST_SLEEP_STATE, 0x03, pm_state);
 
 	if (pcr->ops->force_power_down)
-		pcr->ops->force_power_down(pcr, pm_state);
+		pcr->ops->force_power_down(pcr, pm_state, runtime);
 	else
-		rtsx_base_force_power_down(pcr, pm_state);
+		rtsx_base_force_power_down(pcr);
 }
 
 void rtsx_pci_enable_ocp(struct rtsx_pcr *pcr)
@@ -1416,7 +1342,9 @@
 
 static int rtsx_pci_init_chip(struct rtsx_pcr *pcr)
 {
-	int err;
+	struct rtsx_cr_option *option = &(pcr->option);
+	int err, l1ss;
+	u32 lval;
 	u16 cfg_val;
 	u8 val;
 
@@ -1501,6 +1429,48 @@
 			pcr->aspm_enabled = true;
 	}
 
+	l1ss = pci_find_ext_capability(pcr->pci, PCI_EXT_CAP_ID_L1SS);
+	if (l1ss) {
+		pci_read_config_dword(pcr->pci, l1ss + PCI_L1SS_CTL1, &lval);
+
+		if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
+			rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
+		else
+			rtsx_clear_dev_flag(pcr, ASPM_L1_1_EN);
+
+		if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
+			rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
+		else
+			rtsx_clear_dev_flag(pcr, ASPM_L1_2_EN);
+
+		if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
+			rtsx_set_dev_flag(pcr, PM_L1_1_EN);
+		else
+			rtsx_clear_dev_flag(pcr, PM_L1_1_EN);
+
+		if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
+			rtsx_set_dev_flag(pcr, PM_L1_2_EN);
+		else
+			rtsx_clear_dev_flag(pcr, PM_L1_2_EN);
+
+		pcie_capability_read_word(pcr->pci, PCI_EXP_DEVCTL2, &cfg_val);
+		if (cfg_val & PCI_EXP_DEVCTL2_LTR_EN) {
+			option->ltr_enabled = true;
+			option->ltr_active = true;
+		} else {
+			option->ltr_enabled = false;
+		}
+
+		if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
+				| PM_L1_1_EN | PM_L1_2_EN))
+			option->force_clkreq_0 = false;
+		else
+			option->force_clkreq_0 = true;
+	} else {
+		option->ltr_enabled = false;
+		option->force_clkreq_0 = true;
+	}
+
 	if (pcr->ops->fetch_vendor_settings)
 		pcr->ops->fetch_vendor_settings(pcr);
 
@@ -1581,7 +1551,7 @@
 	pcr->remap_addr = ioremap(base, len);
 	if (!pcr->remap_addr) {
 		ret = -ENOMEM;
-		goto free_handle;
+		goto free_idr;
 	}
 
 	pcr->rtsx_resv_buf = dma_alloc_coherent(&(pcidev->dev),
@@ -1598,7 +1568,6 @@
 	pcr->card_inserted = 0;
 	pcr->card_removed = 0;
 	INIT_DELAYED_WORK(&pcr->carddet_work, rtsx_pci_card_detect);
-	INIT_DELAYED_WORK(&pcr->idle_work, rtsx_pci_idle_work);
 
 	pcr->msi_en = msi_en;
 	if (pcr->msi_en) {
@@ -1623,20 +1592,14 @@
 		rtsx_pcr_cells[i].pdata_size = sizeof(*handle);
 	}
 
-	if (pcr->rtd3_en) {
-		INIT_DELAYED_WORK(&pcr->rtd3_work, rtsx_pci_rtd3_work);
-		pm_runtime_allow(&pcidev->dev);
-		pm_runtime_enable(&pcidev->dev);
-		pcr->is_runtime_suspended = false;
-	}
-
 
 	ret = mfd_add_devices(&pcidev->dev, pcr->id, rtsx_pcr_cells,
 			ARRAY_SIZE(rtsx_pcr_cells), NULL, 0, NULL);
 	if (ret < 0)
 		goto free_slots;
 
-	schedule_delayed_work(&pcr->idle_work, msecs_to_jiffies(200));
+	pm_runtime_allow(&pcidev->dev);
+	pm_runtime_put(&pcidev->dev);
 
 	return 0;
 
@@ -1651,6 +1614,10 @@
 			pcr->rtsx_resv_buf, pcr->rtsx_resv_buf_addr);
 unmap:
 	iounmap(pcr->remap_addr);
+free_idr:
+	spin_lock(&rtsx_pci_lock);
+	idr_remove(&rtsx_pci_idr, pcr->id);
+	spin_unlock(&rtsx_pci_lock);
 free_handle:
 	kfree(handle);
 free_pcr:
@@ -1668,11 +1635,11 @@
 	struct pcr_handle *handle = pci_get_drvdata(pcidev);
 	struct rtsx_pcr *pcr = handle->pcr;
 
-	if (pcr->rtd3_en)
-		pm_runtime_get_noresume(&pcr->pci->dev);
-
 	pcr->remove_pci = true;
 
+	pm_runtime_get_sync(&pcidev->dev);
+	pm_runtime_forbid(&pcidev->dev);
+
 	/* Disable interrupts at the pcr level */
 	spin_lock_irq(&pcr->lock);
 	rtsx_pci_writel(pcr, RTSX_BIER, 0);
@@ -1680,9 +1647,6 @@
 	spin_unlock_irq(&pcr->lock);
 
 	cancel_delayed_work_sync(&pcr->carddet_work);
-	cancel_delayed_work_sync(&pcr->idle_work);
-	if (pcr->rtd3_en)
-		cancel_delayed_work_sync(&pcr->rtd3_work);
 
 	mfd_remove_devices(&pcidev->dev);
 
@@ -1700,11 +1664,6 @@
 	idr_remove(&rtsx_pci_idr, pcr->id);
 	spin_unlock(&rtsx_pci_lock);
 
-	if (pcr->rtd3_en) {
-		pm_runtime_disable(&pcr->pci->dev);
-		pm_runtime_put_noidle(&pcr->pci->dev);
-	}
-
 	kfree(pcr->slots);
 	kfree(pcr);
 	kfree(handle);
@@ -1717,22 +1676,16 @@
 static int __maybe_unused rtsx_pci_suspend(struct device *dev_d)
 {
 	struct pci_dev *pcidev = to_pci_dev(dev_d);
-	struct pcr_handle *handle;
-	struct rtsx_pcr *pcr;
+	struct pcr_handle *handle = pci_get_drvdata(pcidev);
+	struct rtsx_pcr *pcr = handle->pcr;
 
 	dev_dbg(&(pcidev->dev), "--> %s\n", __func__);
 
-	handle = pci_get_drvdata(pcidev);
-	pcr = handle->pcr;
-
-	cancel_delayed_work(&pcr->carddet_work);
-	cancel_delayed_work(&pcr->idle_work);
+	cancel_delayed_work_sync(&pcr->carddet_work);
 
 	mutex_lock(&pcr->pcr_mutex);
 
-	rtsx_pci_power_off(pcr, HOST_ENTER_S3);
-
-	device_wakeup_disable(dev_d);
+	rtsx_pci_power_off(pcr, HOST_ENTER_S3, false);
 
 	mutex_unlock(&pcr->pcr_mutex);
 	return 0;
@@ -1741,15 +1694,12 @@
 static int __maybe_unused rtsx_pci_resume(struct device *dev_d)
 {
 	struct pci_dev *pcidev = to_pci_dev(dev_d);
-	struct pcr_handle *handle;
-	struct rtsx_pcr *pcr;
+	struct pcr_handle *handle = pci_get_drvdata(pcidev);
+	struct rtsx_pcr *pcr = handle->pcr;
 	int ret = 0;
 
 	dev_dbg(&(pcidev->dev), "--> %s\n", __func__);
 
-	handle = pci_get_drvdata(pcidev);
-	pcr = handle->pcr;
-
 	mutex_lock(&pcr->pcr_mutex);
 
 	ret = rtsx_pci_write_register(pcr, HOST_SLEEP_STATE, 0x03, 0x00);
@@ -1760,8 +1710,6 @@
 	if (ret)
 		goto out;
 
-	schedule_delayed_work(&pcr->idle_work, msecs_to_jiffies(200));
-
 out:
 	mutex_unlock(&pcr->pcr_mutex);
 	return ret;
@@ -1769,16 +1717,46 @@
 
 #ifdef CONFIG_PM
 
+static void rtsx_enable_aspm(struct rtsx_pcr *pcr)
+{
+	if (pcr->ops->set_aspm)
+		pcr->ops->set_aspm(pcr, true);
+	else
+		rtsx_comm_set_aspm(pcr, true);
+}
+
+static void rtsx_comm_pm_power_saving(struct rtsx_pcr *pcr)
+{
+	struct rtsx_cr_option *option = &pcr->option;
+
+	if (option->ltr_enabled) {
+		u32 latency = option->ltr_l1off_latency;
+
+		if (rtsx_check_dev_flag(pcr, L1_SNOOZE_TEST_EN))
+			mdelay(option->l1_snooze_delay);
+
+		rtsx_set_ltr_latency(pcr, latency);
+	}
+
+	if (rtsx_check_dev_flag(pcr, LTR_L1SS_PWR_GATE_EN))
+		rtsx_set_l1off_sub_cfg_d0(pcr, 0);
+
+	rtsx_enable_aspm(pcr);
+}
+
+static void rtsx_pm_power_saving(struct rtsx_pcr *pcr)
+{
+	rtsx_comm_pm_power_saving(pcr);
+}
+
 static void rtsx_pci_shutdown(struct pci_dev *pcidev)
 {
-	struct pcr_handle *handle;
-	struct rtsx_pcr *pcr;
+	struct pcr_handle *handle = pci_get_drvdata(pcidev);
+	struct rtsx_pcr *pcr = handle->pcr;
 
 	dev_dbg(&(pcidev->dev), "--> %s\n", __func__);
 
-	handle = pci_get_drvdata(pcidev);
-	pcr = handle->pcr;
-	rtsx_pci_power_off(pcr, HOST_ENTER_S1);
+	rtsx_pci_power_off(pcr, HOST_ENTER_S1, false);
 
 	pci_disable_device(pcidev);
 	free_irq(pcr->irq, (void *)pcr);
@@ -1786,28 +1764,47 @@
 		pci_disable_msi(pcr->pci);
 }
 
-static int rtsx_pci_runtime_suspend(struct device *device)
+static int rtsx_pci_runtime_idle(struct device *device)
 {
 	struct pci_dev *pcidev = to_pci_dev(device);
-	struct pcr_handle *handle;
-	struct rtsx_pcr *pcr;
-
-	handle = pci_get_drvdata(pcidev);
-	pcr = handle->pcr;
-	dev_dbg(&(pcidev->dev), "--> %s\n", __func__);
+	struct pcr_handle *handle = pci_get_drvdata(pcidev);
+	struct rtsx_pcr *pcr = handle->pcr;
 
-	cancel_delayed_work(&pcr->carddet_work);
-	cancel_delayed_work(&pcr->rtd3_work);
-	cancel_delayed_work(&pcr->idle_work);
+	dev_dbg(device, "--> %s\n", __func__);
 
 	mutex_lock(&pcr->pcr_mutex);
-	rtsx_pci_power_off(pcr, HOST_ENTER_S3);
 
-	free_irq(pcr->irq, (void *)pcr);
+	pcr->state = PDEV_STAT_IDLE;
+
+	if (pcr->ops->disable_auto_blink)
+		pcr->ops->disable_auto_blink(pcr);
+	if (pcr->ops->turn_off_led)
+		pcr->ops->turn_off_led(pcr);
+
+	rtsx_pm_power_saving(pcr);
 
 	mutex_unlock(&pcr->pcr_mutex);
 
-	pcr->is_runtime_suspended = true;
+	if (pcr->rtd3_en)
+		pm_schedule_suspend(device, 10000);
+
+	return -EBUSY;
+}
+
+static int rtsx_pci_runtime_suspend(struct device *device)
+{
+	struct pci_dev *pcidev = to_pci_dev(device);
+	struct pcr_handle *handle = pci_get_drvdata(pcidev);
+	struct rtsx_pcr *pcr = handle->pcr;
+
+	dev_dbg(device, "--> %s\n", __func__);
+
+	cancel_delayed_work_sync(&pcr->carddet_work);
+
+	mutex_lock(&pcr->pcr_mutex);
+	rtsx_pci_power_off(pcr, HOST_ENTER_S3, true);
+
+	mutex_unlock(&pcr->pcr_mutex);
 
 	return 0;
 }
@@ -1815,21 +1812,14 @@
 static int rtsx_pci_runtime_resume(struct device *device)
 {
 	struct pci_dev *pcidev = to_pci_dev(device);
-	struct pcr_handle *handle;
-	struct rtsx_pcr *pcr;
+	struct pcr_handle *handle = pci_get_drvdata(pcidev);
+	struct rtsx_pcr *pcr = handle->pcr;
 
-	handle = pci_get_drvdata(pcidev);
-	pcr = handle->pcr;
-	dev_dbg(&(pcidev->dev), "--> %s\n", __func__);
+	dev_dbg(device, "--> %s\n", __func__);
 
 	mutex_lock(&pcr->pcr_mutex);
 
 	rtsx_pci_write_register(pcr, HOST_SLEEP_STATE, 0x03, 0x00);
-	rtsx_pci_acquire_irq(pcr);
-	synchronize_irq(pcr->irq);
-
-	if (pcr->ops->fetch_vendor_settings)
-		pcr->ops->fetch_vendor_settings(pcr);
 
 	rtsx_pci_init_hw(pcr);
 
@@ -1838,8 +1828,6 @@
 				pcr->slots[RTSX_SD_CARD].p_dev);
 	}
 
-	schedule_delayed_work(&pcr->idle_work, msecs_to_jiffies(200));
-
 	mutex_unlock(&pcr->pcr_mutex);
 	return 0;
 }
@@ -1854,7 +1842,7 @@
 
 static const struct dev_pm_ops rtsx_pci_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(rtsx_pci_suspend, rtsx_pci_resume)
-	SET_RUNTIME_PM_OPS(rtsx_pci_runtime_suspend, rtsx_pci_runtime_resume, NULL)
+	SET_RUNTIME_PM_OPS(rtsx_pci_runtime_suspend, rtsx_pci_runtime_resume, rtsx_pci_runtime_idle)
 };
 
 static struct pci_driver rtsx_pci_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rtsx_pcr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rtsx_pcr.h
@@ -15,6 +15,8 @@
 #define MIN_DIV_N_PCR		80
 #define MAX_DIV_N_PCR		208
 
+#define RTS522A_PME_FORCE_CTL	0xFF78
+#define RTS522A_AUTOLOAD_CFG1	0xFF7C
 #define RTS522A_PM_CTRL3		0xFF7E
 
 #define RTS524A_PME_FORCE_CTL		0xFF78
@@ -25,6 +27,7 @@
 #define REG_EFUSE_POWEROFF		0x00
 #define RTS5250_CLK_CFG3		0xFF79
 #define RTS525A_CFG_MEM_PD		0xF0
+#define RTS524A_AUTOLOAD_CFG1		0xFF7C
 #define RTS524A_PM_CTRL3		0xFF7E
 #define RTS525A_BIOS_CFG		0xFF2D
 #define RTS525A_LOAD_BIOS_FLAG	0x01
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cardreader/rtsx_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cardreader/rtsx_usb.c
@@ -631,16 +631,20 @@
 
 	ucr->pusb_dev = usb_dev;
 
-	ucr->iobuf = usb_alloc_coherent(ucr->pusb_dev, IOBUF_SIZE,
-			GFP_KERNEL, &ucr->iobuf_dma);
-	if (!ucr->iobuf)
+	ucr->cmd_buf = kmalloc(IOBUF_SIZE, GFP_KERNEL);
+	if (!ucr->cmd_buf)
 		return -ENOMEM;
 
+	ucr->rsp_buf = kmalloc(IOBUF_SIZE, GFP_KERNEL);
+	if (!ucr->rsp_buf) {
+		ret = -ENOMEM;
+		goto out_free_cmd_buf;
+	}
+
 	usb_set_intfdata(intf, ucr);
 
 	ucr->vendor_id = id->idVendor;
 	ucr->product_id = id->idProduct;
-	ucr->cmd_buf = ucr->rsp_buf = ucr->iobuf;
 
 	mutex_init(&ucr->dev_mutex);
 
@@ -667,8 +671,12 @@
 	return 0;
 
 out_init_fail:
-	usb_free_coherent(ucr->pusb_dev, IOBUF_SIZE, ucr->iobuf,
-			ucr->iobuf_dma);
+	usb_set_intfdata(ucr->pusb_intf, NULL);
+	kfree(ucr->rsp_buf);
+	ucr->rsp_buf = NULL;
+out_free_cmd_buf:
+	kfree(ucr->cmd_buf);
+	ucr->cmd_buf = NULL;
 	return ret;
 }
 
@@ -681,8 +689,12 @@
 	mfd_remove_devices(&intf->dev);
 
 	usb_set_intfdata(ucr->pusb_intf, NULL);
-	usb_free_coherent(ucr->pusb_dev, IOBUF_SIZE, ucr->iobuf,
-			ucr->iobuf_dma);
+
+	kfree(ucr->cmd_buf);
+	ucr->cmd_buf = NULL;
+
+	kfree(ucr->rsp_buf);
+	ucr->rsp_buf = NULL;
 }
 
 #ifdef CONFIG_PM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cxl/guest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cxl/guest.c
@@ -959,10 +959,10 @@
 	 * if it returns an error!
 	 */
 	if ((rc = cxl_register_afu(afu)))
-		goto err_put1;
+		goto err_put_dev;
 
 	if ((rc = cxl_sysfs_afu_add(afu)))
-		goto err_put1;
+		goto err_del_dev;
 
 	/*
 	 * pHyp doesn't expose the programming models supported by the
@@ -978,7 +978,7 @@
 		afu->modes_supported = CXL_MODE_DIRECTED;
 
 	if ((rc = cxl_afu_select_best_mode(afu)))
-		goto err_put2;
+		goto err_remove_sysfs;
 
 	adapter->afu[afu->slice] = afu;
 
@@ -998,10 +998,12 @@
 
 	return 0;
 
-err_put2:
+err_remove_sysfs:
 	cxl_sysfs_afu_remove(afu);
-err_put1:
-	device_unregister(&afu->dev);
+err_del_dev:
+	device_del(&afu->dev);
+err_put_dev:
+	put_device(&afu->dev);
 	free = false;
 	guest_release_serr_irq(afu);
 err2:
@@ -1135,18 +1137,20 @@
 	 * even if it returns an error!
 	 */
 	if ((rc = cxl_register_adapter(adapter)))
-		goto err_put1;
+		goto err_put_dev;
 
 	if ((rc = cxl_sysfs_adapter_add(adapter)))
-		goto err_put1;
+		goto err_del_dev;
 
 	/* release the context lock as the adapter is configured */
 	cxl_adapter_context_unlock(adapter);
 
 	return adapter;
 
-err_put1:
-	device_unregister(&adapter->dev);
+err_del_dev:
+	device_del(&adapter->dev);
+err_put_dev:
+	put_device(&adapter->dev);
 	free = false;
 	cxl_guest_remove_chardev(adapter);
 err1:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cxl/irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cxl/irq.c
@@ -349,6 +349,7 @@
 
 out:
 	cxl_ops->release_irq_ranges(&ctx->irqs, ctx->afu->adapter);
+	bitmap_free(ctx->irq_bitmap);
 	afu_irq_name_free(ctx);
 	return -ENOMEM;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/cxl/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/cxl/pci.c
@@ -387,6 +387,7 @@
 	rc = get_phb_index(np, phb_index);
 	if (rc) {
 		pr_err("cxl: invalid phb index\n");
+		of_node_put(np);
 		return rc;
 	}
 
@@ -1164,10 +1165,10 @@
 	 * if it returns an error!
 	 */
 	if ((rc = cxl_register_afu(afu)))
-		goto err_put1;
+		goto err_put_dev;
 
 	if ((rc = cxl_sysfs_afu_add(afu)))
-		goto err_put1;
+		goto err_del_dev;
 
 	adapter->afu[afu->slice] = afu;
 
@@ -1176,10 +1177,12 @@
 
 	return 0;
 
-err_put1:
+err_del_dev:
+	device_del(&afu->dev);
+err_put_dev:
 	pci_deconfigure_afu(afu);
 	cxl_debugfs_afu_remove(afu);
-	device_unregister(&afu->dev);
+	put_device(&afu->dev);
 	return rc;
 
 err_free_native:
@@ -1667,23 +1670,25 @@
 	 * even if it returns an error!
 	 */
 	if ((rc = cxl_register_adapter(adapter)))
-		goto err_put1;
+		goto err_put_dev;
 
 	if ((rc = cxl_sysfs_adapter_add(adapter)))
-		goto err_put1;
+		goto err_del_dev;
 
 	/* Release the context lock as adapter is configured */
 	cxl_adapter_context_unlock(adapter);
 
 	return adapter;
 
-err_put1:
+err_del_dev:
+	device_del(&adapter->dev);
+err_put_dev:
 	/* This should mirror cxl_remove_adapter, except without the
 	 * sysfs parts
 	 */
 	cxl_debugfs_adapter_remove(adapter);
 	cxl_deconfigure_adapter(adapter);
-	device_unregister(&adapter->dev);
+	put_device(&adapter->dev);
 	return ERR_PTR(rc);
 
 err_release:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/Kconfig
@@ -6,6 +6,7 @@
 	depends on I2C && SYSFS
 	select NVMEM
 	select NVMEM_SYSFS
+	select REGMAP
 	select REGMAP_I2C
 	help
 	  Enable this driver to get read/write support to most I2C EEPROMs
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/at24.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/at24.c
@@ -585,6 +585,31 @@
 	}
 }
 
+static void at24_probe_temp_sensor(struct i2c_client *client)
+{
+	struct at24_data *at24 = i2c_get_clientdata(client);
+	struct i2c_board_info info = { .type = "jc42" };
+	int ret;
+	u8 val;
+
+	/*
+	 * Byte 2 has value 11 for DDR3, earlier versions don't
+	 * support the thermal sensor present flag
+	 */
+	ret = at24_read(at24, 2, &val, 1);
+	if (ret || val != 11)
+		return;
+
+	/* Byte 32, bit 7 is set if temp sensor is present */
+	ret = at24_read(at24, 32, &val, 1);
+	if (ret || !(val & BIT(7)))
+		return;
+
+	info.addr = 0x18 | (client->addr & 7);
+
+	i2c_new_client_device(client->adapter, &info);
+}
+
 static int at24_probe(struct i2c_client *client)
 {
 	struct regmap_config regmap_config = { };
@@ -757,14 +782,6 @@
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
 
-	at24->nvmem = devm_nvmem_register(dev, &nvmem_config);
-	if (IS_ERR(at24->nvmem)) {
-		pm_runtime_disable(dev);
-		if (!pm_runtime_status_suspended(dev))
-			regulator_disable(at24->vcc_reg);
-		return PTR_ERR(at24->nvmem);
-	}
-
 	/*
 	 * Perform a one-byte test read to verify that the
 	 * chip is functional.
@@ -777,6 +794,19 @@
 		return -ENODEV;
 	}
 
+	at24->nvmem = devm_nvmem_register(dev, &nvmem_config);
+	if (IS_ERR(at24->nvmem)) {
+		pm_runtime_disable(dev);
+		if (!pm_runtime_status_suspended(dev))
+			regulator_disable(at24->vcc_reg);
+		return dev_err_probe(dev, PTR_ERR(at24->nvmem),
+				     "failed to register nvmem\n");
+	}
+
+	/* If this a SPD EEPROM, probe for DDR3 thermal sensor */
+	if (cdata == &at24_data_spd)
+		at24_probe_temp_sensor(client);
+
 	pm_runtime_idle(dev);
 
 	if (writable)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/at25.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/at25.c
@@ -17,8 +17,6 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/eeprom.h>
 #include <linux/property.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
 #include <linux/math.h>
 
 /*
@@ -32,6 +30,8 @@
  */
 
 #define	FM25_SN_LEN	8		/* serial number length */
+#define EE_MAXADDRLEN	3		/* 24 bit addresses, up to 2 MBytes */
+
 struct at25_data {
 	struct spi_device	*spi;
 	struct mutex		lock;
@@ -40,6 +40,7 @@
 	struct nvmem_config	nvmem_config;
 	struct nvmem_device	*nvmem;
 	u8 sernum[FM25_SN_LEN];
+	u8 command[EE_MAXADDRLEN + 1];
 };
 
 #define	AT25_WREN	0x06		/* latch the write enable */
@@ -62,8 +63,6 @@
 
 #define	FM25_ID_LEN	9		/* ID length */
 
-#define EE_MAXADDRLEN	3		/* 24 bit addresses, up to 2 MBytes */
-
 /* Specs often allow 5 msec for a page write, sometimes 20 msec;
  * it's important to recover from write timeouts.
  */
@@ -78,7 +77,6 @@
 {
 	struct at25_data *at25 = priv;
 	char *buf = val;
-	u8			command[EE_MAXADDRLEN + 1];
 	u8			*cp;
 	ssize_t			status;
 	struct spi_transfer	t[2];
@@ -92,12 +90,15 @@
 	if (unlikely(!count))
 		return -EINVAL;
 
-	cp = command;
+	cp = at25->command;
 
 	instr = AT25_READ;
 	if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
 		if (offset >= (1U << (at25->addrlen * 8)))
 			instr |= AT25_INSTR_BIT3;
+
+	mutex_lock(&at25->lock);
+
 	*cp++ = instr;
 
 	/* 8/16/24-bit address is written MSB first */
@@ -116,7 +117,7 @@
 	spi_message_init(&m);
 	memset(t, 0, sizeof(t));
 
-	t[0].tx_buf = command;
+	t[0].tx_buf = at25->command;
 	t[0].len = at25->addrlen + 1;
 	spi_message_add_tail(&t[0], &m);
 
@@ -124,8 +125,6 @@
 	t[1].len = count;
 	spi_message_add_tail(&t[1], &m);
 
-	mutex_lock(&at25->lock);
-
 	/* Read it all at once.
 	 *
 	 * REVISIT that's potentially a problem with large chips, if
@@ -153,7 +152,7 @@
 	spi_message_init(&m);
 	memset(t, 0, sizeof(t));
 
-	t[0].tx_buf = &command;
+	t[0].tx_buf = at25->command;
 	t[0].len = 1;
 	spi_message_add_tail(&t[0], &m);
 
@@ -163,6 +162,8 @@
 
 	mutex_lock(&at25->lock);
 
+	at25->command[0] = command;
+
 	status = spi_sync(at25->spi, &m);
 	dev_dbg(&at25->spi->dev, "read %d aux bytes --> %d\n", len, status);
 
@@ -376,28 +377,31 @@
 static int at25_probe(struct spi_device *spi)
 {
 	struct at25_data	*at25 = NULL;
-	struct spi_eeprom	chip;
 	int			err;
 	int			sr;
 	u8 id[FM25_ID_LEN];
 	u8 sernum[FM25_SN_LEN];
+	bool is_fram;
 	int i;
-	const struct of_device_id *match;
-	bool is_fram = 0;
 
-	match = of_match_device(of_match_ptr(at25_of_match), &spi->dev);
-	if (match && !strcmp(match->compatible, "cypress,fm25"))
-		is_fram = 1;
+	err = device_property_match_string(&spi->dev, "compatible", "cypress,fm25");
+	if (err >= 0)
+		is_fram = true;
+	else
+		is_fram = false;
+
+	at25 = devm_kzalloc(&spi->dev, sizeof(struct at25_data), GFP_KERNEL);
+	if (!at25)
+		return -ENOMEM;
 
 	/* Chip description */
-	if (!spi->dev.platform_data) {
-		if (!is_fram) {
-			err = at25_fw_to_chip(&spi->dev, &chip);
-			if (err)
-				return err;
-		}
-	} else
-		chip = *(struct spi_eeprom *)spi->dev.platform_data;
+	if (spi->dev.platform_data) {
+		memcpy(&at25->chip, spi->dev.platform_data, sizeof(at25->chip));
+	} else if (!is_fram) {
+		err = at25_fw_to_chip(&spi->dev, &at25->chip);
+		if (err)
+			return err;
+	}
 
 	/* Ping the chip ... the status register is pretty portable,
 	 * unlike probing manufacturer IDs.  We do expect that system
@@ -409,12 +413,7 @@
 		return -ENXIO;
 	}
 
-	at25 = devm_kzalloc(&spi->dev, sizeof(struct at25_data), GFP_KERNEL);
-	if (!at25)
-		return -ENOMEM;
-
 	mutex_init(&at25->lock);
-	at25->chip = chip;
 	at25->spi = spi;
 	spi_set_drvdata(spi, at25);
 
@@ -431,7 +430,7 @@
 			dev_err(&spi->dev, "Error: unsupported size (id %02x)\n", id[7]);
 			return -ENODEV;
 		}
-		chip.byte_len = int_pow(2, id[7] - 0x21 + 4) * 1024;
+		at25->chip.byte_len = int_pow(2, id[7] - 0x21 + 4) * 1024;
 
 		if (at25->chip.byte_len > 64 * 1024)
 			at25->chip.flags |= EE_ADDR3;
@@ -464,7 +463,7 @@
 	at25->nvmem_config.type = is_fram ? NVMEM_TYPE_FRAM : NVMEM_TYPE_EEPROM;
 	at25->nvmem_config.name = dev_name(&spi->dev);
 	at25->nvmem_config.dev = &spi->dev;
-	at25->nvmem_config.read_only = chip.flags & EE_READONLY;
+	at25->nvmem_config.read_only = at25->chip.flags & EE_READONLY;
 	at25->nvmem_config.root_only = true;
 	at25->nvmem_config.owner = THIS_MODULE;
 	at25->nvmem_config.compat = true;
@@ -474,17 +473,18 @@
 	at25->nvmem_config.priv = at25;
 	at25->nvmem_config.stride = 1;
 	at25->nvmem_config.word_size = 1;
-	at25->nvmem_config.size = chip.byte_len;
+	at25->nvmem_config.size = at25->chip.byte_len;
 
 	at25->nvmem = devm_nvmem_register(&spi->dev, &at25->nvmem_config);
 	if (IS_ERR(at25->nvmem))
 		return PTR_ERR(at25->nvmem);
 
 	dev_info(&spi->dev, "%d %s %s %s%s, pagesize %u\n",
-		 (chip.byte_len < 1024) ? chip.byte_len : (chip.byte_len / 1024),
-		 (chip.byte_len < 1024) ? "Byte" : "KByte",
+		 (at25->chip.byte_len < 1024) ?
+			at25->chip.byte_len : (at25->chip.byte_len / 1024),
+		 (at25->chip.byte_len < 1024) ? "Byte" : "KByte",
 		 at25->chip.name, is_fram ? "fram" : "eeprom",
-		 (chip.flags & EE_READONLY) ? " (readonly)" : "",
+		 (at25->chip.flags & EE_READONLY) ? " (readonly)" : "",
 		 at25->chip.page_size);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/digsy_mtc_eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/digsy_mtc_eeprom.c
@@ -42,7 +42,7 @@
 }
 
 struct eeprom_93xx46_platform_data digsy_mtc_eeprom_data = {
-	.flags		= EE_ADDR8,
+	.flags		= EE_ADDR8 | EE_SIZE1K,
 	.prepare	= digsy_mtc_op_prepare,
 	.finish		= digsy_mtc_op_finish,
 };
@@ -60,7 +60,7 @@
 };
 
 static struct gpiod_lookup_table eeprom_spi_gpiod_table = {
-	.dev_id         = "spi_gpio",
+	.dev_id         = "spi_gpio.1",
 	.table          = {
 		GPIO_LOOKUP("gpio@b00", GPIO_EEPROM_CLK,
 			    "sck", GPIO_ACTIVE_HIGH),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/ee1004.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/ee1004.c
@@ -114,6 +114,9 @@
 	if (offset + count > EE1004_PAGE_SIZE)
 		count = EE1004_PAGE_SIZE - offset;
 
+	if (count > I2C_SMBUS_BLOCK_MAX)
+		count = I2C_SMBUS_BLOCK_MAX;
+
 	return i2c_smbus_read_i2c_block_data_or_emulated(client, offset, count, buf);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/eeprom_93cx6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/eeprom_93cx6.c
@@ -186,6 +186,11 @@
 	eeprom_93cx6_write_bits(eeprom, command,
 		PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
 
+	if (has_quirk_extra_read_cycle(eeprom)) {
+		eeprom_93cx6_pulse_high(eeprom);
+		eeprom_93cx6_pulse_low(eeprom);
+	}
+
 	/*
 	 * Read the requested 16 bits.
 	 */
@@ -252,6 +257,11 @@
 	eeprom_93cx6_write_bits(eeprom, command,
 		PCI_EEPROM_WIDTH_OPCODE + eeprom->width + 1);
 
+	if (has_quirk_extra_read_cycle(eeprom)) {
+		eeprom_93cx6_pulse_high(eeprom);
+		eeprom_93cx6_pulse_low(eeprom);
+	}
+
 	/*
 	 * Read the requested 8 bits.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/eeprom/idt_89hpesx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/eeprom/idt_89hpesx.c
@@ -909,14 +909,18 @@
 	u32 csraddr, csrval;
 	char *buf;
 
+	if (*offp)
+		return 0;
+
 	/* Copy data from User-space */
 	buf = kmalloc(count + 1, GFP_KERNEL);
 	if (!buf)
 		return -ENOMEM;
 
-	ret = simple_write_to_buffer(buf, count, offp, ubuf, count);
-	if (ret < 0)
+	if (copy_from_user(buf, ubuf, count)) {
+		ret = -EFAULT;
 		goto free_buf;
+	}
 	buf[count] = 0;
 
 	/* Find position of colon in the buffer */
@@ -1564,12 +1568,20 @@
  */
 static int __init idt_init(void)
 {
+	int ret;
+
 	/* Create Debugfs directory first */
 	if (debugfs_initialized())
 		csr_dbgdir = debugfs_create_dir("idt_csr", NULL);
 
 	/* Add new i2c-device driver */
-	return i2c_add_driver(&idt_driver);
+	ret = i2c_add_driver(&idt_driver);
+	if (ret) {
+		debugfs_remove_recursive(csr_dbgdir);
+		return ret;
+	}
+
+	return 0;
 }
 module_init(idt_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/fastrpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/fastrpc.c
@@ -247,6 +247,13 @@
 		dma_buf_put(map->buf);
 	}
 
+	if (map->fl) {
+		spin_lock(&map->fl->lock);
+		list_del(&map->node);
+		spin_unlock(&map->fl->lock);
+		map->fl = NULL;
+	}
+
 	kfree(map);
 }
 
@@ -256,10 +263,12 @@
 		kref_put(&map->refcount, fastrpc_free_map);
 }
 
-static void fastrpc_map_get(struct fastrpc_map *map)
+static int fastrpc_map_get(struct fastrpc_map *map)
 {
-	if (map)
-		kref_get(&map->refcount);
+	if (!map)
+		return -ENOENT;
+
+	return kref_get_unless_zero(&map->refcount) ? 0 : -ENOENT;
 }
 
 static int fastrpc_map_find(struct fastrpc_user *fl, int fd,
@@ -719,16 +728,18 @@
 static u64 fastrpc_get_payload_size(struct fastrpc_invoke_ctx *ctx, int metalen)
 {
 	u64 size = 0;
-	int i;
+	int oix;
 
 	size = ALIGN(metalen, FASTRPC_ALIGN);
-	for (i = 0; i < ctx->nscalars; i++) {
+	for (oix = 0; oix < ctx->nbufs; oix++) {
+		int i = ctx->olaps[oix].raix;
+
 		if (ctx->args[i].fd == 0 || ctx->args[i].fd == -1) {
 
-			if (ctx->olaps[i].offset == 0)
+			if (ctx->olaps[oix].offset == 0)
 				size = ALIGN(size, FASTRPC_ALIGN);
 
-			size += (ctx->olaps[i].mend - ctx->olaps[i].mstart);
+			size += (ctx->olaps[oix].mend - ctx->olaps[oix].mstart);
 		}
 	}
 
@@ -817,7 +828,7 @@
 			mmap_read_lock(current->mm);
 			vma = find_vma(current->mm, ctx->args[i].ptr);
 			if (vma)
-				pages[i].addr += ctx->args[i].ptr -
+				pages[i].addr += (ctx->args[i].ptr & PAGE_MASK) -
 						 vma->vm_start;
 			mmap_read_unlock(current->mm);
 
@@ -984,11 +995,6 @@
 	if (err)
 		goto bail;
 
-	/* Check the response from remote dsp */
-	err = ctx->retval;
-	if (err)
-		goto bail;
-
 	if (ctx->nscalars) {
 		/* make sure that all memory writes by DSP are seen by CPU */
 		dma_rmb();
@@ -998,6 +1004,11 @@
 			goto bail;
 	}
 
+	/* Check the response from remote dsp */
+	err = ctx->retval;
+	if (err)
+		goto bail;
+
 bail:
 	if (err != -ERESTARTSYS && err != -ETIMEDOUT) {
 		/* We are done with this compute context */
@@ -1097,7 +1108,7 @@
 
 	sc = FASTRPC_SCALARS(FASTRPC_RMID_INIT_CREATE, 4, 0);
 	if (init.attrs)
-		sc = FASTRPC_SCALARS(FASTRPC_RMID_INIT_CREATE_ATTR, 6, 0);
+		sc = FASTRPC_SCALARS(FASTRPC_RMID_INIT_CREATE_ATTR, 4, 0);
 
 	err = fastrpc_internal_invoke(fl, true, FASTRPC_INIT_HANDLE,
 				      sc, args);
@@ -1112,12 +1123,7 @@
 	fl->init_mem = NULL;
 	fastrpc_buf_free(imem);
 err_alloc:
-	if (map) {
-		spin_lock(&fl->lock);
-		list_del(&map->node);
-		spin_unlock(&fl->lock);
-		fastrpc_map_put(map);
-	}
+	fastrpc_map_put(map);
 err:
 	kfree(args);
 
@@ -1194,10 +1200,8 @@
 		fastrpc_context_put(ctx);
 	}
 
-	list_for_each_entry_safe(map, m, &fl->maps, node) {
-		list_del(&map->node);
+	list_for_each_entry_safe(map, m, &fl->maps, node)
 		fastrpc_map_put(map);
-	}
 
 	list_for_each_entry_safe(buf, b, &fl->mmaps, node) {
 		list_del(&buf->node);
@@ -1284,7 +1288,14 @@
 	}
 
 	if (copy_to_user(argp, &bp, sizeof(bp))) {
-		dma_buf_put(buf->dmabuf);
+		/*
+		 * The usercopy failed, but we can't do much about it, as
+		 * dma_buf_fd() already called fd_install() and made the
+		 * file descriptor accessible for the current process. It
+		 * might already be closed and dmabuf no longer valid when
+		 * we reach this point. Therefore "leak" the fd and rely on
+		 * the process exit path to do any required cleanup.
+		 */
 		return -EFAULT;
 	}
 
@@ -1342,17 +1353,18 @@
 				   struct fastrpc_req_munmap *req)
 {
 	struct fastrpc_invoke_args args[1] = { [0] = { 0 } };
-	struct fastrpc_buf *buf, *b;
+	struct fastrpc_buf *buf = NULL, *iter, *b;
 	struct fastrpc_munmap_req_msg req_msg;
 	struct device *dev = fl->sctx->dev;
 	int err;
 	u32 sc;
 
 	spin_lock(&fl->lock);
-	list_for_each_entry_safe(buf, b, &fl->mmaps, node) {
-		if ((buf->raddr == req->vaddrout) && (buf->size == req->size))
+	list_for_each_entry_safe(iter, b, &fl->mmaps, node) {
+		if ((iter->raddr == req->vaddrout) && (iter->size == req->size)) {
+			buf = iter;
 			break;
-		buf = NULL;
+		}
 	}
 	spin_unlock(&fl->lock);
 
@@ -1540,7 +1552,12 @@
 	of_property_read_u32(dev->of_node, "qcom,nsessions", &sessions);
 
 	spin_lock_irqsave(&cctx->lock, flags);
-	sess = &cctx->session[cctx->sesscount];
+	if (cctx->sesscount >= FASTRPC_MAX_SESSIONS) {
+		dev_err(&pdev->dev, "too many sessions\n");
+		spin_unlock_irqrestore(&cctx->lock, flags);
+		return -ENOSPC;
+	}
+	sess = &cctx->session[cctx->sesscount++];
 	sess->used = false;
 	sess->valid = true;
 	sess->dev = dev;
@@ -1553,13 +1570,12 @@
 		struct fastrpc_session_ctx *dup_sess;
 
 		for (i = 1; i < sessions; i++) {
-			if (cctx->sesscount++ >= FASTRPC_MAX_SESSIONS)
+			if (cctx->sesscount >= FASTRPC_MAX_SESSIONS)
 				break;
-			dup_sess = &cctx->session[cctx->sesscount];
+			dup_sess = &cctx->session[cctx->sesscount++];
 			memcpy(dup_sess, sess, sizeof(*dup_sess));
 		}
 	}
-	cctx->sesscount++;
 	spin_unlock_irqrestore(&cctx->lock, flags);
 	rc = dma_set_mask(dev, DMA_BIT_MASK(32));
 	if (rc) {
@@ -1578,7 +1594,7 @@
 	int i;
 
 	spin_lock_irqsave(&cctx->lock, flags);
-	for (i = 1; i < FASTRPC_MAX_SESSIONS; i++) {
+	for (i = 0; i < FASTRPC_MAX_SESSIONS; i++) {
 		if (cctx->session[i].sid == sess->sid) {
 			cctx->session[i].valid = false;
 			cctx->sesscount--;
@@ -1661,8 +1677,10 @@
 	struct fastrpc_invoke_ctx *ctx;
 
 	spin_lock(&user->lock);
-	list_for_each_entry(ctx, &user->pending, node)
+	list_for_each_entry(ctx, &user->pending, node) {
+		ctx->retval = -EPIPE;
 		complete(&ctx->work);
+	}
 	spin_unlock(&user->lock);
 }
 
@@ -1672,7 +1690,9 @@
 	struct fastrpc_user *user;
 	unsigned long flags;
 
+	/* No invocations past this point */
 	spin_lock_irqsave(&cctx->lock, flags);
+	cctx->rpdev = NULL;
 	list_for_each_entry(user, &cctx->users, user)
 		fastrpc_notify_users(user);
 	spin_unlock_irqrestore(&cctx->lock, flags);
@@ -1680,7 +1700,6 @@
 	misc_deregister(&cctx->miscdev);
 	of_platform_depopulate(&rpdev->dev);
 
-	cctx->rpdev = NULL;
 	fastrpc_channel_ctx_put(cctx);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/habanalabs/common/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/habanalabs/common/debugfs.c
@@ -856,6 +856,8 @@
 		pci_set_power_state(hdev->pdev, PCI_D0);
 		pci_restore_state(hdev->pdev);
 		rc = pci_enable_device(hdev->pdev);
+		if (rc < 0)
+			return rc;
 	} else if (value == 2) {
 		pci_save_state(hdev->pdev);
 		pci_disable_device(hdev->pdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/habanalabs/common/firmware_if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/habanalabs/common/firmware_if.c
@@ -1703,6 +1703,9 @@
 		return rc;
 	}
 
+	/* here we can mark the descriptor as valid as the content has been validated */
+	fw_loader->dynamic_loader.fw_desc_valid = true;
+
 	return 0;
 }
 
@@ -1759,7 +1762,13 @@
 		return rc;
 	}
 
-	/* extract address copy the descriptor from */
+	/*
+	 * extract address to copy the descriptor from
+	 * in addition, as the descriptor value is going to be over-ridden by new data- we mark it
+	 * as invalid.
+	 * it will be marked again as valid once validated
+	 */
+	fw_loader->dynamic_loader.fw_desc_valid = false;
 	src = hdev->pcie_bar[region->bar_id] + region->offset_in_bar +
 							response->ram_offset;
 	memcpy_fromio(fw_desc, src, sizeof(struct lkd_fw_comms_desc));
@@ -2239,6 +2248,9 @@
 	dev_info(hdev->dev,
 		"Loading firmware to device, may take some time...\n");
 
+	/* initialize FW descriptor as invalid */
+	fw_loader->dynamic_loader.fw_desc_valid = false;
+
 	/*
 	 * In this stage, "cpu_dyn_regs" contains only LKD's hard coded values!
 	 * It will be updated from FW after hl_fw_dynamic_request_descriptor().
@@ -2325,7 +2337,8 @@
 	return 0;
 
 protocol_err:
-	fw_read_errors(hdev, le32_to_cpu(dyn_regs->cpu_boot_err0),
+	if (fw_loader->dynamic_loader.fw_desc_valid)
+		fw_read_errors(hdev, le32_to_cpu(dyn_regs->cpu_boot_err0),
 				le32_to_cpu(dyn_regs->cpu_boot_err1),
 				le32_to_cpu(dyn_regs->cpu_boot_dev_sts0),
 				le32_to_cpu(dyn_regs->cpu_boot_dev_sts1));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/habanalabs/common/habanalabs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/habanalabs/common/habanalabs.h
@@ -992,6 +992,7 @@
  * @image_region: region to copy the FW image to
  * @fw_image_size: size of FW image to load
  * @wait_for_bl_timeout: timeout for waiting for boot loader to respond
+ * @fw_desc_valid: true if FW descriptor has been validated and hence the data can be used
  */
 struct dynamic_fw_load_mgr {
 	struct fw_response response;
@@ -999,6 +1000,7 @@
 	struct pci_mem_region *image_region;
 	size_t fw_image_size;
 	u32 wait_for_bl_timeout;
+	bool fw_desc_valid;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/habanalabs/common/mmu/mmu_v1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/habanalabs/common/mmu/mmu_v1.c
@@ -467,7 +467,7 @@
 {
 	/* MMU H/W fini was already done in device hw_fini() */
 
-	if (!ZERO_OR_NULL_PTR(hdev->mmu_priv.hr.mmu_shadow_hop0)) {
+	if (!ZERO_OR_NULL_PTR(hdev->mmu_priv.dr.mmu_shadow_hop0)) {
 		kvfree(hdev->mmu_priv.dr.mmu_shadow_hop0);
 		gen_pool_destroy(hdev->mmu_priv.dr.mmu_pgt_pool);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/habanalabs/gaudi/gaudi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/habanalabs/gaudi/gaudi.c
@@ -3318,19 +3318,19 @@
 	u32 nic_qm_err_cfg, irq_handler_offset;
 	u32 q_off;
 
-	mtr_base_en_lo = lower_32_bits(CFG_BASE +
+	mtr_base_en_lo = lower_32_bits((CFG_BASE & U32_MAX) +
 			mmSYNC_MNGR_E_N_SYNC_MNGR_OBJS_MON_PAY_ADDRL_0);
 	mtr_base_en_hi = upper_32_bits(CFG_BASE +
 				mmSYNC_MNGR_E_N_SYNC_MNGR_OBJS_MON_PAY_ADDRL_0);
-	so_base_en_lo = lower_32_bits(CFG_BASE +
+	so_base_en_lo = lower_32_bits((CFG_BASE & U32_MAX) +
 				mmSYNC_MNGR_E_N_SYNC_MNGR_OBJS_SOB_OBJ_0);
 	so_base_en_hi = upper_32_bits(CFG_BASE +
 				mmSYNC_MNGR_E_N_SYNC_MNGR_OBJS_SOB_OBJ_0);
-	mtr_base_ws_lo = lower_32_bits(CFG_BASE +
+	mtr_base_ws_lo = lower_32_bits((CFG_BASE & U32_MAX) +
 				mmSYNC_MNGR_W_S_SYNC_MNGR_OBJS_MON_PAY_ADDRL_0);
 	mtr_base_ws_hi = upper_32_bits(CFG_BASE +
 				mmSYNC_MNGR_W_S_SYNC_MNGR_OBJS_MON_PAY_ADDRL_0);
-	so_base_ws_lo = lower_32_bits(CFG_BASE +
+	so_base_ws_lo = lower_32_bits((CFG_BASE & U32_MAX) +
 				mmSYNC_MNGR_W_S_SYNC_MNGR_OBJS_SOB_OBJ_0);
 	so_base_ws_hi = upper_32_bits(CFG_BASE +
 				mmSYNC_MNGR_W_S_SYNC_MNGR_OBJS_SOB_OBJ_0);
@@ -5744,15 +5744,17 @@
 {
 	struct asic_fixed_properties *asic_prop = &hdev->asic_prop;
 	struct gaudi_device *gaudi = hdev->asic_specific;
-	u32 nic_mask_q_id = 1 << (HW_CAP_NIC_SHIFT +
-		((parser->hw_queue_id - GAUDI_QUEUE_ID_NIC_0_0) >> 2));
+	u32 nic_queue_offset, nic_mask_q_id;
 
 	if ((parser->hw_queue_id >= GAUDI_QUEUE_ID_NIC_0_0) &&
-			(parser->hw_queue_id <= GAUDI_QUEUE_ID_NIC_9_3) &&
-			(!(gaudi->hw_cap_initialized & nic_mask_q_id))) {
-		dev_err(hdev->dev, "h/w queue %d is disabled\n",
-				parser->hw_queue_id);
-		return -EINVAL;
+			(parser->hw_queue_id <= GAUDI_QUEUE_ID_NIC_9_3)) {
+		nic_queue_offset = parser->hw_queue_id - GAUDI_QUEUE_ID_NIC_0_0;
+		nic_mask_q_id = 1 << (HW_CAP_NIC_SHIFT + (nic_queue_offset >> 2));
+
+		if (!(gaudi->hw_cap_initialized & nic_mask_q_id)) {
+			dev_err(hdev->dev, "h/w queue %d is disabled\n", parser->hw_queue_id);
+			return -EINVAL;
+		}
 	}
 
 	/* For internal queue jobs just check if CB address is valid */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/Kconfig
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (c) 2021, Intel Corporation. All rights reserved.
+
+config INTEL_VSC
+	tristate "Intel VSC"
+	select INTEL_MEI_VSC
+	help
+	  Add support of Intel Visual Sensing Controller (IVSC).
+
+config INTEL_VSC_CSI
+	tristate "Intel VSC CSI client"
+	depends on INTEL_VSC
+	select INTEL_MEI
+	help
+	  Add CSI support for Intel Visual Sensing Controller (IVSC).
+
+config INTEL_VSC_ACE
+	tristate "Intel VSC ACE client"
+	depends on INTEL_VSC
+	select INTEL_MEI
+	help
+	  Add ACE support for Intel Visual Sensing Controller (IVSC).
+
+config INTEL_VSC_PSE
+	tristate "Intel VSC PSE client"
+	depends on DEBUG_FS
+	select INTEL_MEI
+	select INTEL_MEI_VSC
+	help
+	  Add PSE support for Intel Visual Sensing Controller (IVSC) to
+	  expose debugging information in files under /sys/kernel/debug/.
+
+config INTEL_VSC_ACE_DEBUG
+	tristate "Intel VSC ACE debug client"
+	depends on DEBUG_FS
+	select INTEL_MEI
+	select INTEL_MEI_VSC
+	help
+	  Add ACE debug support for Intel Visual Sensing Controller (IVSC)
+	  to expose debugging information in files under /sys/kernel/debug/.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Copyright (c) 2021, Intel Corporation. All rights reserved.
+
+obj-$(CONFIG_INTEL_VSC)			+= intel_vsc.o
+obj-$(CONFIG_INTEL_VSC_CSI)		+= mei_csi.o
+obj-$(CONFIG_INTEL_VSC_ACE)		+= mei_ace.o
+obj-$(CONFIG_INTEL_VSC_PSE)		+= mei_pse.o
+obj-$(CONFIG_INTEL_VSC_ACE_DEBUG)	+= mei_ace_debug.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/intel_vsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/intel_vsc.c
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2021 Intel Corporation */
+
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/vsc.h>
+
+#include "intel_vsc.h"
+
+#define ACE_PRIVACY_ON 2
+
+struct intel_vsc {
+	spinlock_t lock;
+	struct mutex mutex;
+
+	void *csi;
+	struct vsc_csi_ops *csi_ops;
+	uint16_t csi_registerred;
+
+	void *ace;
+	struct vsc_ace_ops *ace_ops;
+	uint16_t ace_registerred;
+};
+
+static struct intel_vsc vsc;
+
+static int check_component_ready(void)
+{
+	int ret = -1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&vsc.lock, flags);
+
+	if (vsc.ace_registerred && vsc.csi_registerred)
+		ret = 0;
+
+	spin_unlock_irqrestore(&vsc.lock, flags);
+
+	return ret;
+}
+
+static void update_camera_status(struct vsc_camera_status *status,
+				 struct camera_status *s)
+{
+	if (status && s) {
+		status->owner = s->camera_owner;
+		status->exposure_level = s->exposure_level;
+		status->status = VSC_PRIVACY_OFF;
+
+		if (s->privacy_stat == ACE_PRIVACY_ON)
+			status->status = VSC_PRIVACY_ON;
+	}
+}
+
+int vsc_register_ace(void *ace, struct vsc_ace_ops *ops)
+{
+	unsigned long flags;
+
+	if (ace && ops) {
+		if (ops->ipu_own_camera && ops->ace_own_camera) {
+			spin_lock_irqsave(&vsc.lock, flags);
+
+			vsc.ace = ace;
+			vsc.ace_ops = ops;
+			vsc.ace_registerred = true;
+
+			spin_unlock_irqrestore(&vsc.lock, flags);
+
+			return 0;
+		}
+	}
+
+	pr_err("register ace failed\n");
+	return -1;
+}
+EXPORT_SYMBOL_GPL(vsc_register_ace);
+
+void vsc_unregister_ace(void)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vsc.lock, flags);
+
+	vsc.ace_registerred = false;
+
+	spin_unlock_irqrestore(&vsc.lock, flags);
+}
+EXPORT_SYMBOL_GPL(vsc_unregister_ace);
+
+int vsc_register_csi(void *csi, struct vsc_csi_ops *ops)
+{
+	unsigned long flags;
+
+	if (csi && ops) {
+		if (ops->set_privacy_callback &&
+		    ops->set_owner && ops->set_mipi_conf) {
+			spin_lock_irqsave(&vsc.lock, flags);
+
+			vsc.csi = csi;
+			vsc.csi_ops = ops;
+			vsc.csi_registerred = true;
+
+			spin_unlock_irqrestore(&vsc.lock, flags);
+
+			return 0;
+		}
+	}
+
+	pr_err("register csi failed\n");
+	return -1;
+}
+EXPORT_SYMBOL_GPL(vsc_register_csi);
+
+void vsc_unregister_csi(void)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vsc.lock, flags);
+
+	vsc.csi_registerred = false;
+
+	spin_unlock_irqrestore(&vsc.lock, flags);
+}
+EXPORT_SYMBOL_GPL(vsc_unregister_csi);
+
+int vsc_acquire_camera_sensor(struct vsc_mipi_config *config,
+			      vsc_privacy_callback_t callback,
+			      void *handle,
+			      struct vsc_camera_status *status)
+{
+	int ret;
+	struct camera_status s;
+	struct mipi_conf conf = { 0 };
+
+	struct vsc_csi_ops *csi_ops;
+	struct vsc_ace_ops *ace_ops;
+
+	if (!config)
+		return -EINVAL;
+
+	ret = check_component_ready();
+	if (ret < 0) {
+		pr_info("intel vsc not ready\n");
+		return -EAGAIN;
+	}
+
+	mutex_lock(&vsc.mutex);
+	/* no need check component again here */
+
+	csi_ops = vsc.csi_ops;
+	ace_ops = vsc.ace_ops;
+
+	csi_ops->set_privacy_callback(vsc.csi, callback, handle);
+
+	ret = ace_ops->ipu_own_camera(vsc.ace, &s);
+	if (ret) {
+		pr_err("ipu own camera failed\n");
+		goto err;
+	}
+	update_camera_status(status, &s);
+
+	ret = csi_ops->set_owner(vsc.csi, CSI_IPU);
+	if (ret) {
+		pr_err("ipu own csi failed\n");
+		goto err;
+	}
+
+	conf.lane_num = config->lane_num;
+	conf.freq = config->freq;
+	ret = csi_ops->set_mipi_conf(vsc.csi, &conf);
+	if (ret) {
+		pr_err("config mipi failed\n");
+		goto err;
+	}
+
+err:
+	mutex_unlock(&vsc.mutex);
+	msleep(100);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(vsc_acquire_camera_sensor);
+
+int vsc_release_camera_sensor(struct vsc_camera_status *status)
+{
+	int ret;
+	struct camera_status s;
+
+	struct vsc_csi_ops *csi_ops;
+	struct vsc_ace_ops *ace_ops;
+
+	ret = check_component_ready();
+	if (ret < 0) {
+		pr_info("intel vsc not ready\n");
+		return -EAGAIN;
+	}
+
+	mutex_lock(&vsc.mutex);
+	/* no need check component again here */
+
+	csi_ops = vsc.csi_ops;
+	ace_ops = vsc.ace_ops;
+
+	csi_ops->set_privacy_callback(vsc.csi, NULL, NULL);
+
+	ret = csi_ops->set_owner(vsc.csi, CSI_FW);
+	if (ret) {
+		pr_err("vsc own csi failed\n");
+		goto err;
+	}
+
+	ret = ace_ops->ace_own_camera(vsc.ace, &s);
+	if (ret) {
+		pr_err("vsc own camera failed\n");
+		goto err;
+	}
+	update_camera_status(status, &s);
+
+err:
+	mutex_unlock(&vsc.mutex);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(vsc_release_camera_sensor);
+
+static int __init intel_vsc_init(void)
+{
+	memset(&vsc, 0, sizeof(struct intel_vsc));
+
+	spin_lock_init(&vsc.lock);
+	mutex_init(&vsc.mutex);
+
+	vsc.csi_registerred = false;
+	vsc.ace_registerred = false;
+
+	return 0;
+}
+
+static void __exit intel_vsc_exit(void)
+{
+}
+
+module_init(intel_vsc_init);
+module_exit(intel_vsc_exit);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_SOFTDEP("post: mei_csi mei_ace");
+MODULE_DESCRIPTION("Device driver for Intel VSC");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/intel_vsc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/intel_vsc.h
@@ -0,0 +1,177 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _INTEL_VSC_H_
+#define _INTEL_VSC_H_
+
+#include <linux/types.h>
+
+/* csi power state definition */
+enum csi_power_state {
+	POWER_OFF = 0,
+	POWER_ON,
+};
+
+/* csi ownership definition */
+enum csi_owner {
+	CSI_FW = 0,
+	CSI_IPU,
+};
+
+/* mipi configuration structure */
+struct mipi_conf {
+	uint32_t lane_num;
+	uint32_t freq;
+
+	/* for future use */
+	uint32_t rsvd[2];
+} __packed;
+
+/* camera status structure */
+struct camera_status {
+	uint8_t camera_owner : 2;
+	uint8_t privacy_stat : 2;
+
+	/* for future use */
+	uint8_t rsvd : 4;
+
+	uint32_t exposure_level;
+} __packed;
+
+struct vsc_ace_ops {
+	/**
+	 * @brief ace own camera ownership
+	 *
+	 * @param ace The pointer of ace client device
+	 * @param status The pointer of camera status
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*ace_own_camera)(void *ace, struct camera_status *status);
+
+	/**
+	 * @brief ipu own camera ownership
+	 *
+	 * @param ace The pointer of ace client device
+	 * @param status The pointer of camera status
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*ipu_own_camera)(void *ace, struct camera_status *status);
+
+	/**
+	 * @brief get current camera status
+	 *
+	 * @param ace The pointer of ace client device
+	 * @param status The pointer of camera status
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*get_camera_status)(void *ace, struct camera_status *status);
+};
+
+struct vsc_csi_ops {
+	/**
+	 * @brief set csi ownership
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param owner The csi ownership going to set
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*set_owner)(void *csi, enum csi_owner owner);
+
+	/**
+	 * @brief get current csi ownership
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param owner The pointer of csi ownership
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*get_owner)(void *csi, enum csi_owner *owner);
+
+	/**
+	 * @brief configure csi with provided parameter
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param config The pointer of csi configuration
+	 *        parameter going to set
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*set_mipi_conf)(void *csi, struct mipi_conf *conf);
+
+	/**
+	 * @brief get the current csi configuration
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param config The pointer of csi configuration parameter
+	 *        holding the returned result
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*get_mipi_conf)(void *csi, struct mipi_conf *conf);
+
+	/**
+	 * @brief set csi power state
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param status csi power status going to set
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*set_power_state)(void *csi, enum csi_power_state state);
+
+	/**
+	 * @brief get csi power state
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param status The pointer of variable holding csi power status
+	 *
+	 * @return 0 on success, negative on failure
+	 */
+	int (*get_power_state)(void *csi, enum csi_power_state *state);
+
+	/**
+	 * @brief set csi privacy callback
+	 *
+	 * @param csi The pointer of csi client device
+	 * @param callback The pointer of privacy callback function
+	 * @param handle Privacy callback runtime context
+	 */
+	void (*set_privacy_callback)(void *csi,
+				     vsc_privacy_callback_t callback,
+				     void *handle);
+};
+
+/**
+ * @brief register ace client
+ *
+ * @param ace The pointer of ace client device
+ * @param ops The pointer of ace ops
+ *
+ * @return 0 on success, negative on failure
+ */
+int vsc_register_ace(void *ace, struct vsc_ace_ops *ops);
+
+/**
+ * @brief unregister ace client
+ */
+void vsc_unregister_ace(void);
+
+/**
+ * @brief register csi client
+ *
+ * @param csi The pointer of csi client device
+ * @param ops The pointer of csi ops
+ *
+ * @return 0 on success, negative on failure
+ */
+int vsc_register_csi(void *csi, struct vsc_csi_ops *ops);
+
+/**
+ * @brief unregister csi client
+ */
+void vsc_unregister_csi(void);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/mei_ace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/mei_ace.c
@@ -0,0 +1,589 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2021 Intel Corporation */
+
+#include <linux/completion.h>
+#include <linux/kernel.h>
+#include <linux/mei_cl_bus.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/uuid.h>
+#include <linux/vsc.h>
+
+#include "intel_vsc.h"
+
+#define ACE_TIMEOUT			(5 * HZ)
+#define MEI_ACE_DRIVER_NAME		"vsc_ace"
+
+#define UUID_GET_FW_ID UUID_LE(0x6167DCFB, 0x72F1, 0x4584, \
+			       0xBF, 0xE3, 0x84, 0x17, 0x71, 0xAA, 0x79, 0x0B)
+
+enum notif_rsp {
+	NOTIF = 0,
+	REPLY = 1,
+};
+
+enum notify_type {
+	FW_READY = 8,
+	EXCEPTION = 10,
+	WATCHDOG_TIMEOUT = 15,
+	MANAGEMENT_NOTIF = 16,
+	NOTIFICATION = 27,
+};
+
+enum message_source {
+	FW_MSG = 0,
+	DRV_MSG = 1,
+};
+
+enum notify_event_type {
+	STATE_NOTIF = 0x1,
+	CTRL_NOTIF = 0x2,
+	DPHY_NOTIF = 0x3,
+};
+
+enum ace_cmd_type {
+	ACE_CMD_GET = 3,
+	ACE_CMD_SET = 4,
+};
+
+enum ace_cmd_id {
+	IPU_OWN_CAMERA = 0x13,
+	ACE_OWN_CAMERA = 0x14,
+	GET_CAMERA_STATUS = 0x15,
+	GET_FW_ID = 0x1A,
+};
+
+struct ace_cmd_hdr {
+	uint32_t module_id : 16;
+	uint32_t instance_id : 8;
+	uint32_t type : 5;
+	uint32_t rsp : 1;
+	uint32_t msg_tgt : 1;
+	uint32_t _hw_rsvd_0 : 1;
+
+	uint32_t param_size : 20;
+	uint32_t cmd_id : 8;
+	uint32_t final_block : 1;
+	uint32_t init_block : 1;
+	uint32_t _hw_rsvd_2 : 2;
+} __packed;
+
+union ace_cmd_param {
+	uuid_le uuid;
+	uint32_t param;
+};
+
+struct ace_cmd {
+	struct ace_cmd_hdr hdr;
+	union ace_cmd_param param;
+} __packed;
+
+union ace_notif_hdr {
+	struct _response {
+		uint32_t status : 24;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t param_size : 20;
+		uint32_t cmd_id : 8;
+		uint32_t final_block : 1;
+		uint32_t init_block : 1;
+
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed response;
+
+	struct _notify {
+		uint32_t rsvd2 : 16;
+		uint32_t notif_type : 8;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t rsvd1 : 30;
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed notify;
+
+	struct _management {
+		uint32_t event_id : 16;
+		uint32_t notif_type : 8;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t event_data_size : 16;
+		uint32_t request_target : 1;
+		uint32_t request_type : 5;
+		uint32_t request_id : 8;
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed management;
+};
+
+union ace_notif_cont {
+	uint16_t module_id;
+	uint8_t state_notif;
+	struct camera_status stat;
+};
+
+struct ace_notif {
+	union ace_notif_hdr hdr;
+	union ace_notif_cont cont;
+} __packed;
+
+struct mei_ace {
+	struct mei_cl_device *cldev;
+
+	struct mutex cmd_mutex;
+	struct ace_notif *cmd_resp;
+	struct completion response;
+
+	struct completion reply;
+	struct ace_notif *reply_notif;
+
+	uint16_t module_id;
+	uint16_t init_wait_q_woken;
+	wait_queue_head_t init_wait_q;
+};
+
+static inline void init_cmd_hdr(struct ace_cmd_hdr *hdr)
+{
+	memset(hdr, 0, sizeof(struct ace_cmd_hdr));
+
+	hdr->type = ACE_CMD_SET;
+	hdr->msg_tgt = DRV_MSG;
+	hdr->init_block = 1;
+	hdr->final_block = 1;
+}
+
+static uint16_t get_fw_id(struct mei_ace *ace)
+{
+	int ret;
+
+	ret = wait_event_interruptible(ace->init_wait_q,
+				       ace->init_wait_q_woken);
+	if (ret < 0)
+		dev_warn(&ace->cldev->dev,
+			 "incorrect fw id sent to fw\n");
+
+	return ace->module_id;
+}
+
+static int construct_command(struct mei_ace *ace, struct ace_cmd *cmd,
+			     enum ace_cmd_id cmd_id)
+{
+	struct ace_cmd_hdr *hdr = &cmd->hdr;
+	union ace_cmd_param *param = &cmd->param;
+
+	init_cmd_hdr(hdr);
+
+	hdr->cmd_id = cmd_id;
+	switch (cmd_id) {
+	case GET_FW_ID:
+		param->uuid = UUID_GET_FW_ID;
+		hdr->param_size = sizeof(param->uuid);
+		break;
+	case ACE_OWN_CAMERA:
+		param->param = 0;
+		hdr->module_id = get_fw_id(ace);
+		hdr->param_size = sizeof(param->param);
+		break;
+	case IPU_OWN_CAMERA:
+	case GET_CAMERA_STATUS:
+		hdr->module_id = get_fw_id(ace);
+		break;
+	default:
+		dev_err(&ace->cldev->dev,
+			"sending not supported command");
+		break;
+	}
+
+	return hdr->param_size + sizeof(cmd->hdr);
+}
+
+static int send_command_sync(struct mei_ace *ace,
+			     struct ace_cmd *cmd, size_t len)
+{
+	int ret;
+	struct ace_cmd_hdr *cmd_hdr = &cmd->hdr;
+	union ace_notif_hdr *resp_hdr = &ace->cmd_resp->hdr;
+	union ace_notif_hdr *reply_hdr = &ace->reply_notif->hdr;
+
+	reinit_completion(&ace->response);
+	reinit_completion(&ace->reply);
+
+	ret = mei_cldev_send(ace->cldev, (uint8_t *)cmd, len);
+	if (ret < 0) {
+		dev_err(&ace->cldev->dev,
+			"send command fail %d\n", ret);
+		return ret;
+	}
+
+	ret = wait_for_completion_killable_timeout(&ace->reply, ACE_TIMEOUT);
+	if (ret < 0) {
+		dev_err(&ace->cldev->dev,
+			"command %d notify reply error\n", cmd_hdr->cmd_id);
+		return ret;
+	} else if (ret == 0) {
+		dev_err(&ace->cldev->dev,
+			"command %d notify reply timeout\n", cmd_hdr->cmd_id);
+		ret = -ETIMEDOUT;
+		return ret;
+	}
+
+	if (reply_hdr->response.cmd_id != cmd_hdr->cmd_id) {
+		dev_err(&ace->cldev->dev,
+			"reply notify mismatch, sent %d but got %d\n",
+			cmd_hdr->cmd_id, reply_hdr->response.cmd_id);
+		return -1;
+	}
+
+	ret = reply_hdr->response.status;
+	if (ret) {
+		dev_err(&ace->cldev->dev,
+			"command %d reply wrong status = %d\n",
+			cmd_hdr->cmd_id, ret);
+		return -1;
+	}
+
+	ret = wait_for_completion_killable_timeout(&ace->response, ACE_TIMEOUT);
+	if (ret < 0) {
+		dev_err(&ace->cldev->dev,
+			"command %d response error\n", cmd_hdr->cmd_id);
+		return ret;
+	} else if (ret == 0) {
+		dev_err(&ace->cldev->dev,
+			"command %d response timeout\n", cmd_hdr->cmd_id);
+		ret = -ETIMEDOUT;
+		return ret;
+	}
+
+	if (resp_hdr->management.request_id != cmd_hdr->cmd_id) {
+		dev_err(&ace->cldev->dev,
+			"command response mismatch, sent %d but got %d\n",
+			cmd_hdr->cmd_id, resp_hdr->management.request_id);
+		return -1;
+	}
+
+	return 0;
+}
+
+static int trigger_get_fw_id(struct mei_ace *ace)
+{
+	int ret;
+	struct ace_cmd cmd;
+	size_t cmd_len;
+
+	cmd_len = construct_command(ace, &cmd, GET_FW_ID);
+
+	ret = mei_cldev_send(ace->cldev, (uint8_t *)&cmd, cmd_len);
+	if (ret < 0)
+		dev_err(&ace->cldev->dev,
+			"send get fw id command fail %d\n", ret);
+
+	return ret;
+}
+
+static int set_camera_ownership(struct mei_ace *ace,
+				enum ace_cmd_id cmd_id,
+				struct camera_status *status)
+{
+	struct ace_cmd cmd;
+	size_t cmd_len;
+	union ace_notif_cont *cont;
+	int ret;
+
+	cmd_len = construct_command(ace, &cmd, cmd_id);
+
+	mutex_lock(&ace->cmd_mutex);
+
+	ret = send_command_sync(ace, &cmd, cmd_len);
+	if (!ret) {
+		cont = &ace->cmd_resp->cont;
+		memcpy(status, &cont->stat, sizeof(*status));
+	}
+
+	mutex_unlock(&ace->cmd_mutex);
+
+	return ret;
+}
+
+int ipu_own_camera(void *ace, struct camera_status *status)
+{
+	struct mei_ace *p_ace = (struct mei_ace *)ace;
+
+	return set_camera_ownership(p_ace, IPU_OWN_CAMERA, status);
+}
+
+int ace_own_camera(void *ace, struct camera_status *status)
+{
+	struct mei_ace *p_ace = (struct mei_ace *)ace;
+
+	return set_camera_ownership(p_ace, ACE_OWN_CAMERA, status);
+}
+
+int get_camera_status(void *ace, struct camera_status *status)
+{
+	int ret;
+	struct ace_cmd cmd;
+	size_t cmd_len;
+	union ace_notif_cont *cont;
+	struct mei_ace *p_ace = (struct mei_ace *)ace;
+
+	cmd_len = construct_command(p_ace, &cmd, GET_CAMERA_STATUS);
+
+	mutex_lock(&p_ace->cmd_mutex);
+
+	ret = send_command_sync(p_ace, &cmd, cmd_len);
+	if (!ret) {
+		cont = &p_ace->cmd_resp->cont;
+		memcpy(status, &cont->stat, sizeof(*status));
+	}
+
+	mutex_unlock(&p_ace->cmd_mutex);
+
+	return ret;
+}
+
+static struct vsc_ace_ops ace_ops = {
+	.ace_own_camera = ace_own_camera,
+	.ipu_own_camera = ipu_own_camera,
+	.get_camera_status = get_camera_status,
+};
+
+static void handle_notify(struct mei_ace *ace, struct ace_notif *resp, int len)
+{
+	union ace_notif_hdr *hdr = &resp->hdr;
+	struct mei_cl_device *cldev = ace->cldev;
+
+	if (hdr->notify.msg_tgt != FW_MSG ||
+	    hdr->notify.type != NOTIFICATION) {
+		dev_err(&cldev->dev, "recv incorrect notification\n");
+		return;
+	}
+
+	switch (hdr->notify.notif_type) {
+	/* firmware ready notification sent to driver
+	 * after HECI client connected with firmware.
+	 */
+	case FW_READY:
+		dev_info(&cldev->dev, "firmware ready\n");
+
+		trigger_get_fw_id(ace);
+		break;
+
+	case MANAGEMENT_NOTIF:
+		if (hdr->management.event_id == CTRL_NOTIF) {
+			switch (hdr->management.request_id) {
+			case GET_FW_ID:
+				dev_warn(&cldev->dev,
+					 "shouldn't reach here\n");
+				break;
+
+			case ACE_OWN_CAMERA:
+			case IPU_OWN_CAMERA:
+			case GET_CAMERA_STATUS:
+				memcpy(ace->cmd_resp, resp, len);
+
+				if (!completion_done(&ace->response))
+					complete(&ace->response);
+				break;
+
+			default:
+				dev_err(&cldev->dev,
+					"incorrect command id notif\n");
+				break;
+			}
+		}
+		break;
+
+	case EXCEPTION:
+		dev_err(&cldev->dev, "firmware exception\n");
+		break;
+
+	case WATCHDOG_TIMEOUT:
+		dev_err(&cldev->dev, "firmware watchdog timeout\n");
+		break;
+
+	default:
+		dev_err(&cldev->dev,
+			"recv unknown notification(%d)\n",
+			hdr->notify.notif_type);
+		break;
+	}
+}
+
+ /* callback for command response receive */
+static void mei_ace_rx(struct mei_cl_device *cldev)
+{
+	struct mei_ace *ace = mei_cldev_get_drvdata(cldev);
+	int ret;
+	struct ace_notif resp;
+	union ace_notif_hdr *hdr = &resp.hdr;
+
+	ret = mei_cldev_recv(cldev, (uint8_t *)&resp, sizeof(resp));
+	if (ret < 0) {
+		dev_err(&cldev->dev, "failure in recv %d\n", ret);
+		return;
+	} else if (ret < sizeof(union ace_notif_hdr)) {
+		dev_err(&cldev->dev, "recv small data %d\n", ret);
+		return;
+	}
+
+	switch (hdr->notify.rsp) {
+	case REPLY:
+		if (hdr->response.cmd_id == GET_FW_ID) {
+			ace->module_id = resp.cont.module_id;
+
+			ace->init_wait_q_woken = true;
+			wake_up_all(&ace->init_wait_q);
+
+			dev_info(&cldev->dev, "recv firmware id\n");
+		} else {
+			memcpy(ace->reply_notif, &resp, ret);
+
+			if (!completion_done(&ace->reply))
+				complete(&ace->reply);
+		}
+		break;
+
+	case NOTIF:
+		handle_notify(ace, &resp, ret);
+		break;
+
+	default:
+		dev_err(&cldev->dev,
+			"recv unknown response(%d)\n", hdr->notify.rsp);
+		break;
+	}
+}
+
+static int mei_ace_probe(struct mei_cl_device *cldev,
+			 const struct mei_cl_device_id *id)
+{
+	struct mei_ace *ace;
+	int ret;
+	uint8_t *addr;
+	size_t ace_size = sizeof(struct mei_ace);
+	size_t reply_size = sizeof(struct ace_notif);
+	size_t response_size = sizeof(struct ace_notif);
+
+	ace = kzalloc(ace_size + response_size + reply_size, GFP_KERNEL);
+	if (!ace)
+		return -ENOMEM;
+
+	addr = (uint8_t *)ace;
+	ace->cmd_resp = (struct ace_notif *)(addr + ace_size);
+
+	addr = (uint8_t *)ace->cmd_resp;
+	ace->reply_notif = (struct ace_notif *)(addr + response_size);
+
+	ace->cldev = cldev;
+
+	ace->init_wait_q_woken = false;
+	init_waitqueue_head(&ace->init_wait_q);
+
+	mutex_init(&ace->cmd_mutex);
+	init_completion(&ace->response);
+	init_completion(&ace->reply);
+
+	mei_cldev_set_drvdata(cldev, ace);
+
+	ret = mei_cldev_enable(cldev);
+	if (ret < 0) {
+		dev_err(&cldev->dev,
+			"couldn't enable ace client ret=%d\n", ret);
+		goto err_out;
+	}
+
+	ret = mei_cldev_register_rx_cb(cldev, mei_ace_rx);
+	if (ret) {
+		dev_err(&cldev->dev,
+			"couldn't register rx cb ret=%d\n", ret);
+		goto err_disable;
+	}
+
+	trigger_get_fw_id(ace);
+
+	vsc_register_ace(ace, &ace_ops);
+	return 0;
+
+err_disable:
+	mei_cldev_disable(cldev);
+
+err_out:
+	kfree(ace);
+
+	return ret;
+}
+
+static void mei_ace_remove(struct mei_cl_device *cldev)
+{
+	struct mei_ace *ace = mei_cldev_get_drvdata(cldev);
+
+	vsc_unregister_ace();
+
+	if (!completion_done(&ace->response))
+		complete(&ace->response);
+
+	if (!completion_done(&ace->reply))
+		complete(&ace->reply);
+
+	if (wq_has_sleeper(&ace->init_wait_q))
+		wake_up_all(&ace->init_wait_q);
+
+	mei_cldev_disable(cldev);
+
+	/* wait until no buffer access */
+	mutex_lock(&ace->cmd_mutex);
+	mutex_unlock(&ace->cmd_mutex);
+
+	kfree(ace);
+}
+
+#define MEI_UUID_ACE UUID_LE(0x5DB76CF6, 0x0A68, 0x4ED6, \
+			     0x9B, 0x78, 0x03, 0x61, 0x63, 0x5E, 0x24, 0x47)
+
+static const struct mei_cl_device_id mei_ace_tbl[] = {
+	{ MEI_ACE_DRIVER_NAME, MEI_UUID_ACE, MEI_CL_VERSION_ANY },
+
+	/* required last entry */
+	{ }
+};
+MODULE_DEVICE_TABLE(mei, mei_ace_tbl);
+
+static struct mei_cl_driver mei_ace_driver = {
+	.id_table = mei_ace_tbl,
+	.name = MEI_ACE_DRIVER_NAME,
+
+	.probe = mei_ace_probe,
+	.remove = mei_ace_remove,
+};
+
+static int __init mei_ace_init(void)
+{
+	int ret;
+
+	ret = mei_cldev_driver_register(&mei_ace_driver);
+	if (ret) {
+		pr_err("mei ace driver registration failed: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit mei_ace_exit(void)
+{
+	mei_cldev_driver_unregister(&mei_ace_driver);
+}
+
+module_init(mei_ace_init);
+module_exit(mei_ace_exit);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Device driver for Intel VSC ACE client");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/mei_ace_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/mei_ace_debug.c
@@ -0,0 +1,696 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2021 Intel Corporation */
+
+#include <linux/completion.h>
+#include <linux/debugfs.h>
+#include <linux/fs.h>
+#include <linux/gfp.h>
+#include <linux/kernel.h>
+#include <linux/mei_cl_bus.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/timekeeping.h>
+#include <linux/uuid.h>
+
+#define MAX_RECV_SIZE			8192
+#define MAX_LOG_SIZE			0x40000000
+#define LOG_CONFIG_PARAM_COUNT		7
+#define COMMAND_TIMEOUT 		(5 * HZ)
+#define ACE_LOG_FILE			"/var/log/vsc_ace.log"
+#define MEI_ACE_DEBUG_DRIVER_NAME	"vsc_ace_debug"
+
+enum notif_rsp {
+	NOTIF = 0,
+	REPLY = 1,
+};
+
+enum message_source {
+	FW_MSG = 0,
+	DRV_MSG = 1,
+};
+
+enum notify_type {
+	LOG_BUFFER_STATUS = 6,
+	FW_READY = 8,
+	MANAGEMENT_NOTIF = 16,
+	NOTIFICATION = 27,
+};
+
+enum notify_event_type {
+	STATE_NOTIF = 1,
+	CTRL_NOTIF = 2,
+};
+
+enum ace_cmd_id {
+	GET_FW_VER = 0,
+	LOG_CONFIG = 6,
+	SET_SYS_TIME = 20,
+	GET_FW_ID = 26,
+};
+
+enum ace_cmd_type {
+	ACE_CMD_GET = 3,
+	ACE_CMD_SET = 4,
+};
+
+struct firmware_version {
+	uint32_t type;
+	uint32_t len;
+
+	uint16_t major;
+	uint16_t minor;
+	uint16_t hotfix;
+	uint16_t build;
+} __packed;
+
+union tracing_config {
+	struct _uart_config {
+		uint32_t instance;
+		uint32_t baudrate;
+	} __packed uart;
+
+	struct _i2c_config {
+		uint32_t instance;
+		uint32_t speed;
+		uint32_t address;
+		uint32_t reg;
+	} __packed i2c;
+};
+
+struct log_config {
+	uint32_t aging_period;
+	uint32_t fifo_period;
+	uint32_t enable;
+	uint32_t priority_mask[16];
+	uint32_t tracing_method;
+	uint32_t tracing_format;
+	union tracing_config config;
+} __packed;
+
+struct ace_cmd_hdr {
+	uint32_t module_id : 16;
+	uint32_t instance_id : 8;
+	uint32_t type : 5;
+	uint32_t rsp : 1;
+	uint32_t msg_tgt : 1;
+	uint32_t _hw_rsvd_0 : 1;
+
+	uint32_t param_size : 20;
+	uint32_t cmd_id : 8;
+	uint32_t final_block : 1;
+	uint32_t init_block : 1;
+	uint32_t _hw_rsvd_2 : 2;
+} __packed;
+
+union ace_cmd_param {
+	uuid_le uuid;
+	uint64_t time;
+	struct log_config config;
+};
+
+struct ace_cmd {
+	struct ace_cmd_hdr hdr;
+	union ace_cmd_param param;
+} __packed;
+
+union ace_notif_hdr {
+	struct _response {
+		uint32_t status : 24;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t param_size : 20;
+		uint32_t cmd_id : 8;
+		uint32_t final_block : 1;
+		uint32_t init_block : 1;
+
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed response;
+
+	struct _notify {
+		uint32_t rsvd2 : 16;
+		uint32_t notif_type : 8;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t rsvd1 : 30;
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed notify;
+
+	struct _log_notify {
+		uint32_t rsvd0 : 12;
+		uint32_t source_core : 4;
+		uint32_t notif_type : 8;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t rsvd1 : 30;
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed log_notify;
+
+	struct _management {
+		uint32_t event_id : 16;
+		uint32_t notif_type : 8;
+		uint32_t type : 5;
+		uint32_t rsp : 1;
+		uint32_t msg_tgt : 1;
+		uint32_t _hw_rsvd_0 : 1;
+
+		uint32_t event_data_size : 16;
+		uint32_t request_target : 1;
+		uint32_t request_type : 5;
+		uint32_t request_id : 8;
+		uint32_t _hw_rsvd_2 : 2;
+	} __packed management;
+};
+
+union ace_notif_cont {
+	uint16_t module_id;
+	struct firmware_version version;
+};
+
+struct ace_notif {
+	union ace_notif_hdr hdr;
+	union ace_notif_cont cont;
+} __packed;
+
+struct mei_ace_debug {
+	struct mei_cl_device *cldev;
+
+	struct mutex cmd_mutex;
+	struct ace_notif cmd_resp;
+	struct completion response;
+
+	struct completion reply;
+	struct ace_notif reply_notif;
+
+	loff_t pos;
+	struct file *ace_file;
+
+	uint8_t *recv_buf;
+
+	struct dentry *dfs_dir;
+};
+
+static inline void init_cmd_hdr(struct ace_cmd_hdr *hdr)
+{
+	memset(hdr, 0, sizeof(struct ace_cmd_hdr));
+
+	hdr->type = ACE_CMD_SET;
+	hdr->msg_tgt = DRV_MSG;
+	hdr->init_block = 1;
+	hdr->final_block = 1;
+}
+
+static int construct_command(struct mei_ace_debug *ad,
+			     struct ace_cmd *cmd,
+			     enum ace_cmd_id cmd_id,
+			     void *user_data)
+{
+	struct ace_cmd_hdr *hdr = &cmd->hdr;
+	union ace_cmd_param *param = &cmd->param;
+
+	init_cmd_hdr(hdr);
+
+	hdr->cmd_id = cmd_id;
+	switch (cmd_id) {
+	case GET_FW_VER:
+		hdr->type = ACE_CMD_GET;
+		break;
+	case SET_SYS_TIME:
+		param->time = ktime_get_ns();
+		hdr->param_size = sizeof(param->time);
+		break;
+	case GET_FW_ID:
+		memcpy(&param->uuid, user_data, sizeof(param->uuid));
+		hdr->param_size = sizeof(param->uuid);
+		break;
+	case LOG_CONFIG:
+		memcpy(&param->config, user_data, sizeof(param->config));
+		hdr->param_size = sizeof(param->config);
+		break;
+	default:
+		dev_err(&ad->cldev->dev,
+			"sending not supported command");
+		break;
+	}
+
+	return hdr->param_size + sizeof(cmd->hdr);
+}
+
+static int send_command_sync(struct mei_ace_debug *ad,
+			     struct ace_cmd *cmd, size_t len)
+{
+	int ret;
+	struct ace_cmd_hdr *cmd_hdr = &cmd->hdr;
+	union ace_notif_hdr *reply_hdr = &ad->reply_notif.hdr;
+
+	reinit_completion(&ad->reply);
+
+	ret = mei_cldev_send(ad->cldev, (uint8_t *)cmd, len);
+	if (ret < 0) {
+		dev_err(&ad->cldev->dev,
+			"send command fail %d\n", ret);
+		return ret;
+	}
+
+	ret = wait_for_completion_killable_timeout(&ad->reply, COMMAND_TIMEOUT);
+	if (ret < 0) {
+		dev_err(&ad->cldev->dev,
+			"command %d notify reply error\n", cmd_hdr->cmd_id);
+		return ret;
+	} else if (ret == 0) {
+		dev_err(&ad->cldev->dev,
+			"command %d notify reply timeout\n", cmd_hdr->cmd_id);
+		ret = -ETIMEDOUT;
+		return ret;
+	}
+
+	if (reply_hdr->response.cmd_id != cmd_hdr->cmd_id) {
+		dev_err(&ad->cldev->dev,
+			"reply notify mismatch, sent %d but got %d\n",
+			cmd_hdr->cmd_id, reply_hdr->response.cmd_id);
+		return -1;
+	}
+
+	ret = reply_hdr->response.status;
+	if (ret) {
+		dev_err(&ad->cldev->dev,
+			"command %d reply wrong status = %d\n",
+			cmd_hdr->cmd_id, ret);
+		return -1;
+	}
+
+	return 0;
+}
+
+static int set_system_time(struct mei_ace_debug *ad)
+{
+	struct ace_cmd cmd;
+	size_t cmd_len;
+	int ret;
+
+	cmd_len = construct_command(ad, &cmd, SET_SYS_TIME, NULL);
+
+	mutex_lock(&ad->cmd_mutex);
+	ret = send_command_sync(ad, &cmd, cmd_len);
+	mutex_unlock(&ad->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t ad_time_write(struct file *file,
+			     const char __user *buf,
+			     size_t count, loff_t *ppos)
+{
+	struct mei_ace_debug *ad = file->private_data;
+	int ret;
+
+	ret = set_system_time(ad);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
+static int config_log(struct mei_ace_debug *ad, struct log_config *config)
+{
+	struct ace_cmd cmd;
+	size_t cmd_len;
+	int ret;
+
+	cmd_len = construct_command(ad, &cmd, LOG_CONFIG, config);
+
+	mutex_lock(&ad->cmd_mutex);
+	ret = send_command_sync(ad, &cmd, cmd_len);
+	mutex_unlock(&ad->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t ad_log_config_write(struct file *file,
+				   const char __user *ubuf,
+				   size_t count, loff_t *ppos)
+{
+	struct mei_ace_debug *ad = file->private_data;
+	int ret;
+	uint8_t *buf;
+	struct log_config config = {0};
+
+	buf = memdup_user_nul(ubuf, min(count, (size_t)(PAGE_SIZE - 1)));
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	ret = sscanf(buf, "%u %u %u %u %u %u %u",
+		     &config.aging_period,
+		     &config.fifo_period,
+		     &config.enable,
+		     &config.priority_mask[0],
+		     &config.priority_mask[1],
+		     &config.tracing_format,
+		     &config.tracing_method);
+	if (ret != LOG_CONFIG_PARAM_COUNT) {
+		dev_err(&ad->cldev->dev,
+			"please input all the required parameters\n");
+		return -EINVAL;
+	}
+
+	ret = config_log(ad, &config);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
+static int get_firmware_version(struct mei_ace_debug *ad,
+				struct firmware_version *version)
+{
+	struct ace_cmd cmd;
+	size_t cmd_len;
+	union ace_notif_cont *cont;
+	int ret;
+
+	cmd_len = construct_command(ad, &cmd, GET_FW_VER, NULL);
+
+	mutex_lock(&ad->cmd_mutex);
+	ret = send_command_sync(ad, &cmd, cmd_len);
+	if (!ret) {
+		cont = &ad->reply_notif.cont;
+		memcpy(version, &cont->version, sizeof(*version));
+	}
+	mutex_unlock(&ad->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t ad_firmware_version_read(struct file *file,
+					char __user *buf,
+					size_t count, loff_t *ppos)
+{
+	struct mei_ace_debug *ad = file->private_data;
+	int ret, pos;
+	struct firmware_version version;
+	unsigned long addr = get_zeroed_page(GFP_KERNEL);
+
+	if (!addr)
+		return -ENOMEM;
+
+	ret = get_firmware_version(ad, &version);
+	if (ret)
+		goto out;
+
+	pos = snprintf((char *)addr, PAGE_SIZE,
+		       "firmware version: %u.%u.%u.%u\n",
+		       version.major, version.minor,
+		       version.hotfix, version.build);
+
+	ret = simple_read_from_buffer(buf, count, ppos, (char *)addr, pos);
+
+out:
+	free_page(addr);
+	return ret;
+}
+
+#define AD_DFS_ADD_FILE(name)						\
+	debugfs_create_file(#name, 0644, ad->dfs_dir, ad,		\
+			    &ad_dfs_##name##_fops)
+
+#define AD_DFS_FILE_OPS(name)						\
+static const struct file_operations ad_dfs_##name##_fops = {		\
+	.read = ad_##name##_read,					\
+	.write = ad_##name##_write,					\
+	.open = simple_open,						\
+}
+
+#define AD_DFS_FILE_READ_OPS(name)					\
+static const struct file_operations ad_dfs_##name##_fops = {		\
+	.read = ad_##name##_read,					\
+	.open = simple_open,						\
+}
+
+#define AD_DFS_FILE_WRITE_OPS(name)					\
+static const struct file_operations ad_dfs_##name##_fops = {		\
+	.write = ad_##name##_write,					\
+	.open = simple_open,						\
+}
+
+AD_DFS_FILE_WRITE_OPS(time);
+AD_DFS_FILE_WRITE_OPS(log_config);
+
+AD_DFS_FILE_READ_OPS(firmware_version);
+
+static void handle_notify(struct mei_ace_debug *ad,
+			  struct ace_notif *notif, int len)
+{
+	int ret;
+	struct file *file;
+	loff_t *pos;
+	union ace_notif_hdr *hdr = &notif->hdr;
+	struct mei_cl_device *cldev = ad->cldev;
+
+	if (hdr->notify.msg_tgt != FW_MSG ||
+	    hdr->notify.type != NOTIFICATION) {
+		dev_err(&cldev->dev, "recv wrong notification\n");
+		return;
+	}
+
+	switch (hdr->notify.notif_type) {
+	case FW_READY:
+		/* firmware ready notification sent to driver
+		 * after HECI client connected with firmware.
+		 */
+		dev_info(&cldev->dev, "firmware ready\n");
+		break;
+
+	case LOG_BUFFER_STATUS:
+		if (ad->pos < MAX_LOG_SIZE) {
+			pos = &ad->pos;
+			file = ad->ace_file;
+
+			ret = kernel_write(file,
+					   (uint8_t *)notif + sizeof(*hdr),
+					   len - sizeof(*hdr),
+					   pos);
+			if (ret < 0)
+				dev_err(&cldev->dev,
+					"error in writing log %d\n", ret);
+			else
+				*pos += ret;
+		} else
+			dev_warn(&cldev->dev,
+				 "already exceed max log size\n");
+		break;
+
+	case MANAGEMENT_NOTIF:
+		if (hdr->management.event_id == CTRL_NOTIF) {
+			switch (hdr->management.request_id) {
+			case GET_FW_VER:
+			case LOG_CONFIG:
+			case SET_SYS_TIME:
+			case GET_FW_ID:
+				memcpy(&ad->cmd_resp, notif, len);
+
+				if (!completion_done(&ad->response))
+					complete(&ad->response);
+				break;
+
+			default:
+				dev_err(&cldev->dev,
+					"wrong command id(%d) notif\n",
+					hdr->management.request_id);
+				break;
+			}
+		}
+		break;
+
+	default:
+		dev_info(&cldev->dev,
+			 "unexpected notify(%d)\n", hdr->notify.notif_type);
+		break;
+	}
+}
+
+/* callback for command response receive */
+static void mei_ace_debug_rx(struct mei_cl_device *cldev)
+{
+	struct mei_ace_debug *ad = mei_cldev_get_drvdata(cldev);
+	int ret;
+	struct ace_notif *notif;
+	union ace_notif_hdr *hdr;
+
+	ret = mei_cldev_recv(cldev, ad->recv_buf, MAX_RECV_SIZE);
+	if (ret < 0) {
+		dev_err(&cldev->dev, "failure in recv %d\n", ret);
+		return;
+	} else if (ret < sizeof(union ace_notif_hdr)) {
+		dev_err(&cldev->dev, "recv small data %d\n", ret);
+		return;
+	}
+	notif = (struct ace_notif *)ad->recv_buf;
+	hdr = &notif->hdr;
+
+	switch (hdr->notify.rsp) {
+	case REPLY:
+		memcpy(&ad->reply_notif, notif, sizeof(struct ace_notif));
+
+		if (!completion_done(&ad->reply))
+			complete(&ad->reply);
+		break;
+
+	case NOTIF:
+		handle_notify(ad, notif, ret);
+		break;
+
+	default:
+		dev_err(&cldev->dev,
+			"unexpected response(%d)\n", hdr->notify.rsp);
+		break;
+	}
+}
+
+static int mei_ace_debug_probe(struct mei_cl_device *cldev,
+			       const struct mei_cl_device_id *id)
+{
+	struct mei_ace_debug *ad;
+	int ret;
+	uint32_t order = get_order(MAX_RECV_SIZE);
+
+	ad = kzalloc(sizeof(struct mei_ace_debug), GFP_KERNEL);
+	if (!ad)
+		return -ENOMEM;
+
+	ad->recv_buf = (uint8_t *)__get_free_pages(GFP_KERNEL, order);
+	if (!ad->recv_buf) {
+		kfree(ad);
+		return -ENOMEM;
+	}
+
+	ad->cldev = cldev;
+
+	mutex_init(&ad->cmd_mutex);
+	init_completion(&ad->response);
+	init_completion(&ad->reply);
+
+	mei_cldev_set_drvdata(cldev, ad);
+
+	ret = mei_cldev_enable(cldev);
+	if (ret < 0) {
+		dev_err(&cldev->dev,
+			"couldn't enable ace debug client ret=%d\n", ret);
+		goto err_out;
+	}
+
+	ret = mei_cldev_register_rx_cb(cldev, mei_ace_debug_rx);
+	if (ret) {
+		dev_err(&cldev->dev,
+			"couldn't register ace debug rx cb ret=%d\n", ret);
+		goto err_disable;
+	}
+
+	ad->ace_file = filp_open(ACE_LOG_FILE,
+				 O_CREAT | O_RDWR | O_LARGEFILE | O_TRUNC,
+				 0600);
+	if (IS_ERR(ad->ace_file)) {
+		dev_err(&cldev->dev,
+			"filp_open(%s) failed\n", ACE_LOG_FILE);
+		ret = PTR_ERR(ad->ace_file);
+		goto err_disable;
+	}
+	ad->pos = 0;
+
+	ad->dfs_dir = debugfs_create_dir("vsc_ace", NULL);
+	if (ad->dfs_dir) {
+		AD_DFS_ADD_FILE(log_config);
+		AD_DFS_ADD_FILE(time);
+		AD_DFS_ADD_FILE(firmware_version);
+	}
+
+	return 0;
+
+err_disable:
+	mei_cldev_disable(cldev);
+
+err_out:
+	free_pages((unsigned long)ad->recv_buf, order);
+
+	kfree(ad);
+
+	return ret;
+}
+
+static void mei_ace_debug_remove(struct mei_cl_device *cldev)
+{
+	uint32_t order = get_order(MAX_RECV_SIZE);
+	struct mei_ace_debug *ad = mei_cldev_get_drvdata(cldev);
+
+	if (!completion_done(&ad->response))
+		complete(&ad->response);
+
+	if (!completion_done(&ad->reply))
+		complete(&ad->reply);
+
+	mei_cldev_disable(cldev);
+
+	debugfs_remove_recursive(ad->dfs_dir);
+
+	filp_close(ad->ace_file, NULL);
+
+	/* wait until no buffer access */
+	mutex_lock(&ad->cmd_mutex);
+	mutex_unlock(&ad->cmd_mutex);
+
+	free_pages((unsigned long)ad->recv_buf, order);
+
+	kfree(ad);
+}
+
+#define MEI_UUID_ACE_DEBUG UUID_LE(0xFB285857, 0xFC24, 0x4BF3, 0xBD, \
+				   0x80, 0x2A, 0xBC, 0x44, 0xE3, 0xC2, 0x0B)
+
+static const struct mei_cl_device_id mei_ace_debug_tbl[] = {
+	{ MEI_ACE_DEBUG_DRIVER_NAME, MEI_UUID_ACE_DEBUG, MEI_CL_VERSION_ANY },
+
+	/* required last entry */
+	{ }
+};
+MODULE_DEVICE_TABLE(mei, mei_ace_debug_tbl);
+
+static struct mei_cl_driver mei_ace_debug_driver = {
+	.id_table = mei_ace_debug_tbl,
+	.name = MEI_ACE_DEBUG_DRIVER_NAME,
+
+	.probe = mei_ace_debug_probe,
+	.remove = mei_ace_debug_remove,
+};
+
+static int __init mei_ace_debug_init(void)
+{
+	int ret;
+
+	ret = mei_cldev_driver_register(&mei_ace_debug_driver);
+	if (ret) {
+		pr_err("mei ace debug driver registration failed: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit mei_ace_debug_exit(void)
+{
+	mei_cldev_driver_unregister(&mei_ace_debug_driver);
+}
+
+module_init(mei_ace_debug_init);
+module_exit(mei_ace_debug_exit);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Device driver for Intel VSC ACE debug client");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/mei_csi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/mei_csi.c
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2021 Intel Corporation */
+
+#include <linux/completion.h>
+#include <linux/kernel.h>
+#include <linux/mei_cl_bus.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/uuid.h>
+#include <linux/vsc.h>
+
+#include "intel_vsc.h"
+
+#define CSI_TIMEOUT			(5 * HZ)
+#define MEI_CSI_DRIVER_NAME		"vsc_csi"
+
+/**
+ * Identify the command id that can be downloaded
+ * to firmware, as well as the privacy notify id
+ * used when processing privacy actions.
+ *
+ * This enumeration is local to the mei csi.
+ */
+enum csi_cmd_id {
+	/* used to set csi ownership */
+	CSI_SET_OWNER,
+
+	/* used to get csi ownership */
+	CSI_GET_OWNER,
+
+	/* used to configurate mipi */
+	CSI_SET_MIPI_CONF,
+
+	/* used to get current mipi configuration */
+	CSI_GET_MIPI_CONF,
+
+	/* used to set csi power state */
+	CSI_SET_POWER_STATE,
+
+	/* used to get csi power state */
+	CSI_GET_POWER_STATE,
+
+	/* privacy notification id used when privacy state changes */
+	CSI_PRIVACY_NOTIF,
+};
+
+enum privacy_state {
+	PRIVACY_OFF = 0,
+	PRIVACY_ON,
+};
+
+/**
+ * CSI command structure.
+ */
+struct csi_cmd {
+	uint32_t cmd_id;
+	union _cmd_param {
+		uint32_t param;
+		struct mipi_conf conf;
+	} param;
+} __packed;
+
+/**
+ * CSI command response structure.
+ */
+struct csi_notif {
+	uint32_t cmd_id;
+	int status;
+	union _resp_cont {
+		uint32_t cont;
+		struct mipi_conf conf;
+	} cont;
+} __packed;
+
+struct mei_csi {
+	struct mei_cl_device *cldev;
+
+	struct mutex cmd_mutex;
+	struct csi_notif *notif;
+	struct completion response;
+
+	spinlock_t privacy_lock;
+	void *handle;
+	vsc_privacy_callback_t callback;
+};
+
+static int mei_csi_send(struct mei_csi *csi, uint8_t *buf, size_t len)
+{
+	struct csi_cmd *cmd = (struct csi_cmd *)buf;
+	int ret;
+
+	reinit_completion(&csi->response);
+
+	ret = mei_cldev_send(csi->cldev, buf, len);
+	if (ret < 0) {
+		dev_err(&csi->cldev->dev,
+			"send command fail %d\n", ret);
+		return ret;
+	}
+
+	ret = wait_for_completion_killable_timeout(&csi->response, CSI_TIMEOUT);
+	if (ret < 0) {
+		dev_err(&csi->cldev->dev,
+			"command %d response error\n", cmd->cmd_id);
+		return ret;
+	} else if (ret == 0) {
+		dev_err(&csi->cldev->dev,
+			"command %d response timeout\n", cmd->cmd_id);
+		ret = -ETIMEDOUT;
+		return ret;
+	}
+
+	ret = csi->notif->status;
+	if (ret == -1) {
+		dev_info(&csi->cldev->dev,
+			 "privacy on, command id = %d\n", cmd->cmd_id);
+		ret = 0;
+	} else if (ret) {
+		dev_err(&csi->cldev->dev,
+			"command %d response fail %d\n", cmd->cmd_id, ret);
+		return ret;
+	}
+
+	if (csi->notif->cmd_id != cmd->cmd_id) {
+		dev_err(&csi->cldev->dev,
+			"command response id mismatch, sent %d but got %d\n",
+			cmd->cmd_id, csi->notif->cmd_id);
+		ret = -1;
+	}
+
+	return ret;
+}
+
+static int csi_set_owner(void *csi, enum csi_owner owner)
+{
+	struct csi_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	cmd.cmd_id = CSI_SET_OWNER;
+	cmd.param.param = owner;
+	cmd_len += sizeof(cmd.param.param);
+
+	mutex_lock(&p_csi->cmd_mutex);
+	ret = mei_csi_send(p_csi, (uint8_t *)&cmd, cmd_len);
+	mutex_unlock(&p_csi->cmd_mutex);
+
+	return ret;
+}
+
+static int csi_get_owner(void *csi, enum csi_owner *owner)
+{
+	struct csi_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	cmd.cmd_id = CSI_GET_OWNER;
+
+	mutex_lock(&p_csi->cmd_mutex);
+	ret = mei_csi_send(p_csi, (uint8_t *)&cmd, cmd_len);
+	if (!ret)
+		*owner = p_csi->notif->cont.cont;
+	mutex_unlock(&p_csi->cmd_mutex);
+
+	return ret;
+}
+
+static int csi_set_mipi_conf(void *csi, struct mipi_conf *conf)
+{
+	struct csi_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	cmd.cmd_id = CSI_SET_MIPI_CONF;
+	cmd.param.conf.freq = conf->freq;
+	cmd.param.conf.lane_num = conf->lane_num;
+	cmd_len += sizeof(cmd.param.conf);
+
+	mutex_lock(&p_csi->cmd_mutex);
+	ret = mei_csi_send(p_csi, (uint8_t *)&cmd, cmd_len);
+	mutex_unlock(&p_csi->cmd_mutex);
+
+	return ret;
+}
+
+static int csi_get_mipi_conf(void *csi, struct mipi_conf *conf)
+{
+	struct csi_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	struct mipi_conf *res;
+	int ret;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	cmd.cmd_id = CSI_GET_MIPI_CONF;
+
+	mutex_lock(&p_csi->cmd_mutex);
+	ret = mei_csi_send(p_csi, (uint8_t *)&cmd, cmd_len);
+	if (!ret) {
+		res = &p_csi->notif->cont.conf;
+		conf->freq = res->freq;
+		conf->lane_num = res->lane_num;
+	}
+	mutex_unlock(&p_csi->cmd_mutex);
+
+	return ret;
+}
+
+static int csi_set_power_state(void *csi, enum csi_power_state state)
+{
+	struct csi_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	cmd.cmd_id = CSI_SET_POWER_STATE;
+	cmd.param.param = state;
+	cmd_len += sizeof(cmd.param.param);
+
+	mutex_lock(&p_csi->cmd_mutex);
+	ret = mei_csi_send(p_csi, (uint8_t *)&cmd, cmd_len);
+	mutex_unlock(&p_csi->cmd_mutex);
+
+	return ret;
+}
+
+static int csi_get_power_state(void *csi, enum csi_power_state *state)
+{
+	struct csi_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	cmd.cmd_id = CSI_GET_POWER_STATE;
+
+	mutex_lock(&p_csi->cmd_mutex);
+	ret = mei_csi_send(p_csi, (uint8_t *)&cmd, cmd_len);
+	if (!ret)
+		*state = p_csi->notif->cont.cont;
+	mutex_unlock(&p_csi->cmd_mutex);
+
+	return ret;
+}
+
+static void csi_set_privacy_callback(void *csi,
+				     vsc_privacy_callback_t callback,
+				     void *handle)
+{
+	unsigned long flags;
+	struct mei_csi *p_csi = (struct mei_csi *)csi;
+
+	spin_lock_irqsave(&p_csi->privacy_lock, flags);
+	p_csi->callback = callback;
+	p_csi->handle = handle;
+	spin_unlock_irqrestore(&p_csi->privacy_lock, flags);
+}
+
+static struct vsc_csi_ops csi_ops = {
+	.set_owner = csi_set_owner,
+	.get_owner = csi_get_owner,
+	.set_mipi_conf = csi_set_mipi_conf,
+	.get_mipi_conf = csi_get_mipi_conf,
+	.set_power_state = csi_set_power_state,
+	.get_power_state = csi_get_power_state,
+	.set_privacy_callback = csi_set_privacy_callback,
+};
+
+static void privacy_notify(struct mei_csi *csi, uint8_t state)
+{
+	unsigned long flags;
+	void *handle;
+	vsc_privacy_callback_t callback;
+
+	spin_lock_irqsave(&csi->privacy_lock, flags);
+	callback = csi->callback;
+	handle = csi->handle;
+	spin_unlock_irqrestore(&csi->privacy_lock, flags);
+
+	if (callback)
+		callback(handle, state);
+}
+
+/**
+ * callback for command response receive
+ */
+static void mei_csi_rx(struct mei_cl_device *cldev)
+{
+	int ret;
+	struct csi_notif notif = {0};
+	struct mei_csi *csi = mei_cldev_get_drvdata(cldev);
+
+	ret = mei_cldev_recv(cldev, (uint8_t *)&notif,
+			     sizeof(struct csi_notif));
+	if (ret < 0) {
+		dev_err(&cldev->dev, "failure in recv %d\n", ret);
+		return;
+	}
+
+	switch (notif.cmd_id) {
+	case CSI_PRIVACY_NOTIF:
+		switch (notif.cont.cont) {
+		case PRIVACY_ON:
+			privacy_notify(csi, 0);
+
+			dev_info(&cldev->dev, "privacy on\n");
+			break;
+
+		case PRIVACY_OFF:
+			privacy_notify(csi, 1);
+
+			dev_info(&cldev->dev, "privacy off\n");
+			break;
+
+		default:
+			dev_err(&cldev->dev,
+				"recv privacy wrong state\n");
+			break;
+		}
+		break;
+
+	case CSI_SET_OWNER:
+	case CSI_GET_OWNER:
+	case CSI_SET_MIPI_CONF:
+	case CSI_GET_MIPI_CONF:
+	case CSI_SET_POWER_STATE:
+	case CSI_GET_POWER_STATE:
+		memcpy(csi->notif, &notif, ret);
+
+		if (!completion_done(&csi->response))
+			complete(&csi->response);
+		break;
+
+	default:
+		dev_err(&cldev->dev,
+			"recv not supported notification(%d)\n",
+			notif.cmd_id);
+		break;
+	}
+}
+
+static int mei_csi_probe(struct mei_cl_device *cldev,
+			 const struct mei_cl_device_id *id)
+{
+	struct mei_csi *csi;
+	int ret;
+	uint8_t *p;
+	size_t csi_size = sizeof(struct mei_csi);
+
+	p = kzalloc(csi_size + sizeof(struct csi_notif), GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
+	csi = (struct mei_csi *)p;
+	csi->notif = (struct csi_notif *)(p + csi_size);
+
+	csi->cldev = cldev;
+
+	mutex_init(&csi->cmd_mutex);
+	init_completion(&csi->response);
+
+	spin_lock_init(&csi->privacy_lock);
+
+	mei_cldev_set_drvdata(cldev, csi);
+
+	ret = mei_cldev_enable(cldev);
+	if (ret < 0) {
+		dev_err(&cldev->dev,
+			"couldn't enable csi client ret=%d\n", ret);
+		goto err_out;
+	}
+
+	ret = mei_cldev_register_rx_cb(cldev, mei_csi_rx);
+	if (ret) {
+		dev_err(&cldev->dev,
+			"couldn't register rx event ret=%d\n", ret);
+		goto err_disable;
+	}
+
+	vsc_register_csi(csi, &csi_ops);
+
+	return 0;
+
+err_disable:
+	mei_cldev_disable(cldev);
+
+err_out:
+	kfree(csi);
+
+	return ret;
+}
+
+static void mei_csi_remove(struct mei_cl_device *cldev)
+{
+	struct mei_csi *csi = mei_cldev_get_drvdata(cldev);
+
+	vsc_unregister_csi();
+
+	if (!completion_done(&csi->response))
+		complete(&csi->response);
+
+	mei_cldev_disable(cldev);
+
+	/* wait until no buffer access */
+	mutex_lock(&csi->cmd_mutex);
+	mutex_unlock(&csi->cmd_mutex);
+
+	kfree(csi);
+}
+
+#define MEI_UUID_CSI UUID_LE(0x92335FCF, 0x3203, 0x4472, \
+			     0xAF, 0x93, 0x7b, 0x44, 0x53, 0xAC, 0x29, 0xDA)
+
+static const struct mei_cl_device_id mei_csi_tbl[] = {
+	{ MEI_CSI_DRIVER_NAME, MEI_UUID_CSI, MEI_CL_VERSION_ANY },
+
+	/* required last entry */
+	{ }
+};
+MODULE_DEVICE_TABLE(mei, mei_csi_tbl);
+
+static struct mei_cl_driver mei_csi_driver = {
+	.id_table = mei_csi_tbl,
+	.name = MEI_CSI_DRIVER_NAME,
+
+	.probe = mei_csi_probe,
+	.remove = mei_csi_remove,
+};
+
+static int __init mei_csi_init(void)
+{
+	int ret;
+
+	ret = mei_cldev_driver_register(&mei_csi_driver);
+	if (ret) {
+		pr_err("mei csi driver registration failed: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit mei_csi_exit(void)
+{
+	mei_cldev_driver_unregister(&mei_csi_driver);
+}
+
+module_init(mei_csi_init);
+module_exit(mei_csi_exit);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Device driver for Intel VSC CSI client");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ivsc/mei_pse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ivsc/mei_pse.c
@@ -0,0 +1,944 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2021 Intel Corporation */
+
+#include <linux/completion.h>
+#include <linux/debugfs.h>
+#include <linux/fs.h>
+#include <linux/gfp.h>
+#include <linux/kernel.h>
+#include <linux/mei_cl_bus.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/timekeeping.h>
+#include <linux/uuid.h>
+
+#define MEI_PSE_DRIVER_NAME	"vsc_pse"
+
+#define PSE_TIMEOUT		(5 * HZ)
+
+#define CONT_OFFSET		offsetof(struct pse_notif, cont)
+#define NOTIF_HEADER_LEN	8
+
+#define MAX_RECV_SIZE		8192
+#define MAX_LOG_SIZE		0x40000000
+#define EM_LOG_FILE		"/var/log/vsc_em.log"
+#define SEM_LOG_FILE		"/var/log/vsc_sem.log"
+
+#define PM_SUBSYS_MAX		2
+#define PM_STATE_NAME_LEN	16
+#define DEV_NUM			64
+#define DEV_NAME_LEN		32
+
+#define FORMAT			"|%16.32s |%12u "
+#define FORMAT_TAIL		"|\n"
+#define CONSTRUCTED_FORMAT	(FORMAT FORMAT FORMAT FORMAT FORMAT_TAIL)
+#define TITLE			"|   Device Name   | Block Count "
+#define TITLE_TAIL		"|"
+#define CONSTRUCTED_TITLE	(TITLE TITLE TITLE TITLE TITLE_TAIL)
+
+enum pse_cmd_id {
+	LOG_ONOFF = 0,
+	SET_WATERMARK = 1,
+	DUMP_TRACE = 2,
+	SET_TIMEOUT = 3,
+	SET_LOG_LEVEL = 4,
+	SET_TIME = 5,
+	GET_TIME = 6,
+	DUMP_POWER_DATA = 7,
+	TRACE_DATA_NOTIF = 8,
+	GET_FW_VER = 10,
+};
+
+enum pm_state {
+	ACTIVE = 0,
+	CORE_HALT,
+	CORE_CLK_GATE,
+	DEEP_SLEEP,
+	STATE_MAX,
+};
+
+struct fw_version {
+	uint32_t major;
+	uint32_t minor;
+	uint32_t hotfix;
+	uint32_t build;
+} __packed;
+
+struct dev_info {
+	char name[DEV_NAME_LEN];
+	uint32_t block_cnt;
+} __packed;
+
+struct dev_list {
+	struct dev_info dev[DEV_NUM];
+	uint32_t dev_cnt;
+} __packed;
+
+struct pm_status {
+	char name[PM_STATE_NAME_LEN];
+	uint64_t start;
+	uint64_t end;
+	uint64_t duration;
+	uint64_t count;
+} __packed;
+
+struct pm_subsys {
+	uint64_t total;
+	struct pm_status status[STATE_MAX];
+	struct dev_list dev;
+	uint16_t crc;
+} __packed;
+
+struct pm_data {
+	struct pm_subsys subsys[PM_SUBSYS_MAX];
+} __packed;
+
+struct pse_cmd {
+	uint32_t cmd_id;
+	union _cmd_param {
+		uint32_t param;
+		uint64_t time;
+	} param;
+} __packed;
+
+struct pse_notif {
+	uint32_t cmd_id;
+	int8_t status;
+	uint8_t source;
+	int16_t size;
+	union _resp_cont {
+		uint64_t time;
+		struct fw_version ver;
+	} cont;
+} __packed;
+
+struct mei_pse {
+	struct mei_cl_device *cldev;
+
+	struct mutex cmd_mutex;
+	struct pse_notif notif;
+	struct completion response;
+
+	uint8_t *recv_buf;
+
+	uint8_t *pm_data;
+	uint32_t pm_data_pos;
+
+	loff_t em_pos;
+	struct file *em_file;
+
+	loff_t sem_pos;
+	struct file *sem_file;
+
+	struct dentry *dfs_dir;
+};
+
+static int mei_pse_send(struct mei_pse *pse, struct pse_cmd *cmd, size_t len)
+{
+	int ret;
+
+	reinit_completion(&pse->response);
+
+	ret = mei_cldev_send(pse->cldev, (uint8_t *)cmd, len);
+	if (ret < 0) {
+		dev_err(&pse->cldev->dev,
+			"send command fail %d\n", ret);
+		return ret;
+	}
+
+	ret = wait_for_completion_killable_timeout(&pse->response, PSE_TIMEOUT);
+	if (ret < 0) {
+		dev_err(&pse->cldev->dev,
+			"command %d response error\n", cmd->cmd_id);
+		return ret;
+	} else if (ret == 0) {
+		dev_err(&pse->cldev->dev,
+			"command %d response timeout\n", cmd->cmd_id);
+		ret = -ETIMEDOUT;
+		return ret;
+	}
+
+	ret = pse->notif.status;
+	if (ret) {
+		dev_err(&pse->cldev->dev,
+			"command %d response fail %d\n", cmd->cmd_id, ret);
+		return ret;
+	}
+
+	if (pse->notif.cmd_id != cmd->cmd_id) {
+		dev_err(&pse->cldev->dev,
+			"command response id mismatch, sent %d but got %d\n",
+			cmd->cmd_id, pse->notif.cmd_id);
+		ret = -1;
+	}
+
+	return ret;
+}
+
+static int pse_log_onoff(struct mei_pse *pse, uint8_t onoff)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	cmd.cmd_id = LOG_ONOFF;
+	cmd.param.param = onoff;
+	cmd_len += sizeof(cmd.param.param);
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_log_onoff_write(struct file *file,
+				   const char __user *buf,
+				   size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret;
+	uint8_t state;
+
+	ret = kstrtou8_from_user(buf, count, 0, &state);
+	if (ret)
+		return ret;
+
+	pse_log_onoff(pse, state);
+
+	return count;
+}
+
+static int pse_set_watermark(struct mei_pse *pse, int val)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	if (val < -1 || val > 100) {
+		dev_err(&pse->cldev->dev, "error water mark value\n");
+		return -1;
+	}
+
+	cmd.cmd_id = SET_WATERMARK;
+	cmd.param.param = val;
+	cmd_len += sizeof(cmd.param.param);
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_watermark_write(struct file *file,
+				   const char __user *buf,
+				   size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret, val;
+
+	ret = kstrtoint_from_user(buf, count, 0, &val);
+	if (ret)
+		return ret;
+
+	pse_set_watermark(pse, val);
+
+	return count;
+}
+
+static int pse_dump_trace(struct mei_pse *pse)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	cmd.cmd_id = DUMP_TRACE;
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_dump_trace_write(struct file *file,
+				    const char __user *buf,
+				    size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret;
+	uint8_t val;
+
+	ret = kstrtou8_from_user(buf, count, 0, &val);
+	if (ret)
+		return ret;
+
+	if (!val)
+		return -EINVAL;
+
+	pse_dump_trace(pse);
+
+	return count;
+}
+
+static int pse_set_timeout(struct mei_pse *pse, int val)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	if (val < -1 || val > 999) {
+		dev_err(&pse->cldev->dev, "error timeout value\n");
+		return -1;
+	}
+
+	cmd.cmd_id = SET_TIMEOUT;
+	cmd.param.param = val;
+	cmd_len += sizeof(cmd.param.param);
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_timeout_write(struct file *file,
+				 const char __user *buf,
+				 size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret, val;
+
+	ret = kstrtoint_from_user(buf, count, 0, &val);
+	if (ret)
+		return ret;
+
+	pse_set_timeout(pse, val);
+
+	return count;
+}
+
+static int pse_set_log_level(struct mei_pse *pse, int val)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	if (val < 0 || val > 4) {
+		dev_err(&pse->cldev->dev, "unsupported log level\n");
+		return -1;
+	}
+
+	cmd.cmd_id = SET_LOG_LEVEL;
+	cmd.param.param = val;
+	cmd_len += sizeof(cmd.param.param);
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_log_level_write(struct file *file,
+				   const char __user *buf,
+				   size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret, val;
+
+	ret = kstrtoint_from_user(buf, count, 0, &val);
+	if (ret)
+		return ret;
+
+	pse_set_log_level(pse, val);
+
+	return count;
+}
+
+static int pse_set_time(struct mei_pse *pse)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	cmd.cmd_id = SET_TIME;
+	cmd.param.time = ktime_get_ns();
+	cmd_len += sizeof(cmd.param.time);
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_time_write(struct file *file,
+			      const char __user *buf,
+			      size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret;
+
+	ret = pse_set_time(pse);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
+static int pse_get_time(struct mei_pse *pse, uint64_t *val)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	cmd.cmd_id = GET_TIME;
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+	if (!ret) {
+		*val = pse->notif.cont.time;
+
+		dev_info(&pse->cldev->dev,
+			 "time = (%llu) nanoseconds\n", *val);
+	}
+
+	return ret;
+}
+
+static ssize_t pse_time_read(struct file *file, char __user *buf,
+			     size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret, pos;
+	uint64_t val;
+	unsigned long addr = get_zeroed_page(GFP_KERNEL);
+
+	if (!addr)
+		return -ENOMEM;
+
+	ret = pse_get_time(pse, &val);
+	if (ret)
+		goto out;
+
+	pos = snprintf((char *)addr, PAGE_SIZE,
+		       "pse time = (%llu) nanoseconds\n", val);
+
+	ret = simple_read_from_buffer(buf, count, ppos, (char *)addr, pos);
+
+out:
+	free_page(addr);
+	return ret;
+}
+
+static int pse_dump_power_data(struct mei_pse *pse)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	cmd.cmd_id = DUMP_POWER_DATA;
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static int dump_power_state_data(struct mei_pse *pse,
+				 char *addr, int pos, int len)
+{
+	const char * const names[] = {"EM7D", "SEM"};
+	const char *title =
+		"| power states | duration(ms) | count | percentage(%) |";
+	struct pm_subsys *subsys;
+	uint64_t total_duration, duration, num, frac;
+	int i, j;
+
+	for (i = 0; i < PM_SUBSYS_MAX; i++) {
+		subsys = &((struct pm_data *)pse->pm_data)->subsys[i];
+
+		pos += snprintf((char *)addr + pos,
+				len - pos,
+				"power state of %s:\n",
+				names[i]);
+
+		pos += snprintf((char *)addr + pos,
+				len - pos,
+				"%s\n",
+				title);
+
+		total_duration = 0;
+		for (j = 0; j < STATE_MAX; j++)
+			total_duration += subsys->status[j].duration;
+
+		for (j = 0; j < STATE_MAX; j++) {
+			duration = subsys->status[j].duration * 100;
+			num = duration / total_duration;
+			frac = (duration % total_duration *
+				10000000 / total_duration + 5) / 10;
+
+			pos += snprintf((char *)addr + pos,
+					len - pos,
+					"|%13.16s |%13llu |%6llu |%7u.%06u |\n",
+					subsys->status[j].name,
+					subsys->status[j].duration,
+					subsys->status[j].count,
+					(uint32_t)num,
+					(uint32_t)frac);
+		}
+
+		pos += snprintf((char *)addr + pos, len - pos, "\n");
+	}
+
+	return pos;
+}
+
+static int dump_dev_power_data(struct mei_pse *pse,
+			       char *addr, int pos, int len)
+{
+	const char * const names[] = {"EM7D", "SEM"};
+	struct pm_subsys *subsys;
+	int i, j;
+	const char *title = CONSTRUCTED_TITLE;
+	const char *format = CONSTRUCTED_FORMAT;
+
+	for (i = 0; i < PM_SUBSYS_MAX; i++) {
+		subsys = &((struct pm_data *)pse->pm_data)->subsys[i];
+
+		pos += snprintf((char *)addr + pos,
+				len - pos,
+				"device list of %s:\n",
+				names[i]);
+
+		pos += snprintf((char *)addr + pos,
+				len - pos,
+				"%s\n",
+				title);
+
+		for (j = 0; j < subsys->dev.dev_cnt; j += 4) {
+			switch (subsys->dev.dev_cnt - j) {
+			case 1:
+				pos += snprintf((char *)addr + pos,
+						len - pos,
+						format,
+						subsys->dev.dev[j].name,
+						subsys->dev.dev[j].block_cnt,
+						"", 0,
+						"", 0,
+						"", 0);
+				break;
+
+			case 2:
+				pos += snprintf((char *)addr + pos,
+						len - pos,
+						format,
+						subsys->dev.dev[j].name,
+						subsys->dev.dev[j].block_cnt,
+						subsys->dev.dev[j+1].name,
+						subsys->dev.dev[j+1].block_cnt,
+						"", 0,
+						"", 0);
+				break;
+
+			case 3:
+				pos += snprintf((char *)addr + pos,
+						len - pos,
+						format,
+						subsys->dev.dev[j].name,
+						subsys->dev.dev[j].block_cnt,
+						subsys->dev.dev[j+1].name,
+						subsys->dev.dev[j+1].block_cnt,
+						subsys->dev.dev[j+2].name,
+						subsys->dev.dev[j+2].block_cnt,
+						"", 0);
+				break;
+
+			default:
+				pos += snprintf((char *)addr + pos,
+						len - pos,
+						format,
+						subsys->dev.dev[j].name,
+						subsys->dev.dev[j].block_cnt,
+						subsys->dev.dev[j+1].name,
+						subsys->dev.dev[j+1].block_cnt,
+						subsys->dev.dev[j+2].name,
+						subsys->dev.dev[j+2].block_cnt,
+						subsys->dev.dev[j+3].name,
+						subsys->dev.dev[j+3].block_cnt);
+				break;
+			}
+		}
+
+		if (i < PM_SUBSYS_MAX - 1)
+			pos += snprintf((char *)addr + pos, len - pos, "\n");
+	}
+
+	return pos;
+}
+
+static ssize_t pse_power_data_read(struct file *file, char __user *buf,
+				   size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	unsigned long addr = get_zeroed_page(GFP_KERNEL);
+	int ret, pos = 0;
+
+	if (!addr)
+		return -ENOMEM;
+
+	ret = pse_dump_power_data(pse);
+	if (ret)
+		goto out;
+
+	pos = dump_power_state_data(pse, (char *)addr, pos, PAGE_SIZE);
+	pos = dump_dev_power_data(pse, (char *)addr, pos, PAGE_SIZE);
+
+	ret = simple_read_from_buffer(buf, count, ppos, (char *)addr, pos);
+
+out:
+	free_page(addr);
+	return ret;
+}
+
+static int pse_get_fw_ver(struct mei_pse *pse, struct fw_version *ver)
+{
+	struct pse_cmd cmd;
+	size_t cmd_len = sizeof(cmd.cmd_id);
+	int ret;
+
+	cmd.cmd_id = GET_FW_VER;
+
+	mutex_lock(&pse->cmd_mutex);
+	ret = mei_pse_send(pse, &cmd, cmd_len);
+	if (!ret) {
+		memcpy(ver, &pse->notif.cont.ver, sizeof(*ver));
+
+		dev_info(&pse->cldev->dev,
+			 "fw version: %u.%u.%u.%u\n",
+			 ver->major, ver->minor, ver->hotfix, ver->build);
+	}
+	mutex_unlock(&pse->cmd_mutex);
+
+	return ret;
+}
+
+static ssize_t pse_fw_ver_read(struct file *file, char __user *buf,
+			       size_t count, loff_t *ppos)
+{
+	struct mei_pse *pse = file->private_data;
+	int ret, pos;
+	struct fw_version ver;
+	unsigned long addr = get_zeroed_page(GFP_KERNEL);
+
+	if (!addr)
+		return -ENOMEM;
+
+	ret = pse_get_fw_ver(pse, &ver);
+	if (ret)
+		goto out;
+
+	pos = snprintf((char *)addr, PAGE_SIZE,
+		       "fw version: %u.%u.%u.%u\n",
+		       ver.major, ver.minor, ver.hotfix, ver.build);
+
+	ret = simple_read_from_buffer(buf, count, ppos, (char *)addr, pos);
+
+out:
+	free_page(addr);
+	return ret;
+}
+
+#define PSE_DFS_ADD_FILE(name)						\
+	debugfs_create_file(#name, 0644, pse->dfs_dir, pse,		\
+			    &pse_dfs_##name##_fops)
+
+#define PSE_DFS_FILE_OPS(name)						\
+static const struct file_operations pse_dfs_##name##_fops = {		\
+	.read = pse_##name##_read,					\
+	.write = pse_##name##_write,					\
+	.open = simple_open,						\
+}
+
+#define PSE_DFS_FILE_READ_OPS(name)					\
+static const struct file_operations pse_dfs_##name##_fops = {		\
+	.read = pse_##name##_read,					\
+	.open = simple_open,						\
+}
+
+#define PSE_DFS_FILE_WRITE_OPS(name)					\
+static const struct file_operations pse_dfs_##name##_fops = {		\
+	.write = pse_##name##_write,					\
+	.open = simple_open,						\
+}
+
+PSE_DFS_FILE_WRITE_OPS(log_onoff);
+PSE_DFS_FILE_WRITE_OPS(watermark);
+PSE_DFS_FILE_WRITE_OPS(dump_trace);
+PSE_DFS_FILE_WRITE_OPS(timeout);
+PSE_DFS_FILE_WRITE_OPS(log_level);
+
+PSE_DFS_FILE_OPS(time);
+
+PSE_DFS_FILE_READ_OPS(fw_ver);
+PSE_DFS_FILE_READ_OPS(power_data);
+
+/* callback for command response receive */
+static void mei_pse_rx(struct mei_cl_device *cldev)
+{
+	int ret;
+	struct pse_notif *notif;
+	struct mei_pse *pse = mei_cldev_get_drvdata(cldev);
+	struct file *file;
+	loff_t *pos;
+
+	ret = mei_cldev_recv(cldev, pse->recv_buf, MAX_RECV_SIZE);
+	if (ret < 0) {
+		dev_err(&cldev->dev, "failure in recv %d\n", ret);
+		return;
+	}
+	notif = (struct pse_notif *)pse->recv_buf;
+
+	switch (notif->cmd_id) {
+	case TRACE_DATA_NOTIF:
+		if (notif->source) {
+			file = pse->sem_file;
+			pos = &pse->sem_pos;
+		} else {
+			file = pse->em_file;
+			pos = &pse->em_pos;
+		}
+
+		if (*pos < MAX_LOG_SIZE) {
+			ret = kernel_write(file,
+					   pse->recv_buf + CONT_OFFSET,
+					   ret - CONT_OFFSET,
+					   pos);
+			if (ret < 0)
+				dev_err(&cldev->dev,
+					"error in writing log %d\n", ret);
+			else
+				*pos += ret;
+		} else
+			dev_warn(&cldev->dev,
+				 "already exceed max log size\n");
+		break;
+
+	case LOG_ONOFF:
+	case SET_WATERMARK:
+	case DUMP_TRACE:
+	case SET_TIMEOUT:
+	case SET_LOG_LEVEL:
+	case SET_TIME:
+	case GET_TIME:
+	case GET_FW_VER:
+		memcpy(&pse->notif, notif, ret);
+
+		if (!completion_done(&pse->response))
+			complete(&pse->response);
+		break;
+
+	case DUMP_POWER_DATA:
+		if (notif->status == 0) {
+			memcpy(pse->pm_data + pse->pm_data_pos,
+			       pse->recv_buf + NOTIF_HEADER_LEN,
+			       ret - NOTIF_HEADER_LEN);
+			pse->pm_data_pos += ret - NOTIF_HEADER_LEN;
+
+			if (pse->pm_data_pos >= sizeof(struct pm_data)) {
+				pse->pm_data_pos = 0;
+				memcpy(&pse->notif, notif, NOTIF_HEADER_LEN);
+
+				if (!completion_done(&pse->response))
+					complete(&pse->response);
+			}
+		} else {
+			dev_err(&cldev->dev, "error in recving power data\n");
+
+			pse->pm_data_pos = 0;
+			memcpy(&pse->notif, notif, NOTIF_HEADER_LEN);
+
+			if (!completion_done(&pse->response))
+				complete(&pse->response);
+		}
+		break;
+
+	default:
+		dev_err(&cldev->dev,
+			"recv not supported notification\n");
+		break;
+	}
+}
+
+static int mei_pse_probe(struct mei_cl_device *cldev,
+			 const struct mei_cl_device_id *id)
+{
+	struct mei_pse *pse;
+	int ret;
+	uint32_t order = get_order(MAX_RECV_SIZE);
+
+	pse = kzalloc(sizeof(struct mei_pse), GFP_KERNEL);
+	if (!pse)
+		return -ENOMEM;
+
+	pse->recv_buf = (uint8_t *)__get_free_pages(GFP_KERNEL, order);
+	if (!pse->recv_buf) {
+		kfree(pse);
+		return -ENOMEM;
+	}
+
+	pse->pm_data = (uint8_t *)__get_free_pages(GFP_KERNEL, order);
+	if (!pse->pm_data) {
+		free_pages((unsigned long)pse->recv_buf, order);
+		kfree(pse);
+		return -ENOMEM;
+	}
+	pse->pm_data_pos = 0;
+
+	pse->cldev = cldev;
+	mutex_init(&pse->cmd_mutex);
+	init_completion(&pse->response);
+
+	mei_cldev_set_drvdata(cldev, pse);
+
+	ret = mei_cldev_enable(cldev);
+	if (ret < 0) {
+		dev_err(&cldev->dev,
+			"couldn't enable pse client ret=%d\n", ret);
+		goto err_out;
+	}
+
+	ret = mei_cldev_register_rx_cb(cldev, mei_pse_rx);
+	if (ret) {
+		dev_err(&cldev->dev,
+			"couldn't register rx event ret=%d\n", ret);
+		goto err_disable;
+	}
+
+	pse->em_file = filp_open(EM_LOG_FILE,
+				 O_CREAT | O_RDWR | O_LARGEFILE | O_TRUNC,
+				 0600);
+	if (IS_ERR(pse->em_file)) {
+		dev_err(&cldev->dev,
+			"filp_open(%s) failed\n", EM_LOG_FILE);
+		ret = PTR_ERR(pse->em_file);
+		goto err_disable;
+	}
+	pse->em_pos = 0;
+
+	pse->sem_file = filp_open(SEM_LOG_FILE,
+				  O_CREAT | O_RDWR | O_LARGEFILE | O_TRUNC,
+				  0600);
+	if (IS_ERR(pse->sem_file)) {
+		dev_err(&cldev->dev,
+			"filp_open(%s) failed\n", SEM_LOG_FILE);
+		ret = PTR_ERR(pse->sem_file);
+		goto err_close;
+	}
+	pse->sem_pos = 0;
+
+	pse->dfs_dir = debugfs_create_dir("vsc_pse", NULL);
+	if (pse->dfs_dir) {
+		PSE_DFS_ADD_FILE(log_onoff);
+		PSE_DFS_ADD_FILE(watermark);
+		PSE_DFS_ADD_FILE(dump_trace);
+		PSE_DFS_ADD_FILE(timeout);
+		PSE_DFS_ADD_FILE(log_level);
+		PSE_DFS_ADD_FILE(time);
+		PSE_DFS_ADD_FILE(fw_ver);
+		PSE_DFS_ADD_FILE(power_data);
+	}
+
+	return 0;
+
+err_close:
+	filp_close(pse->em_file, NULL);
+
+err_disable:
+	mei_cldev_disable(cldev);
+
+err_out:
+	free_pages((unsigned long)pse->pm_data, order);
+
+	free_pages((unsigned long)pse->recv_buf, order);
+
+	kfree(pse);
+
+	return ret;
+}
+
+static void mei_pse_remove(struct mei_cl_device *cldev)
+{
+	struct mei_pse *pse = mei_cldev_get_drvdata(cldev);
+	uint32_t order = get_order(MAX_RECV_SIZE);
+
+	if (!completion_done(&pse->response))
+		complete(&pse->response);
+
+	mei_cldev_disable(cldev);
+
+	debugfs_remove_recursive(pse->dfs_dir);
+
+	filp_close(pse->em_file, NULL);
+	filp_close(pse->sem_file, NULL);
+
+	/* wait until no buffer acccess */
+	mutex_lock(&pse->cmd_mutex);
+	mutex_unlock(&pse->cmd_mutex);
+
+	free_pages((unsigned long)pse->pm_data, order);
+
+	free_pages((unsigned long)pse->recv_buf, order);
+
+	kfree(pse);
+}
+
+#define MEI_UUID_PSE UUID_LE(0xD035E00C, 0x6DAE, 0x4B6D, \
+			     0xB4, 0x7A, 0xF8, 0x8E, 0x30, 0x2A, 0x40, 0x4E)
+
+static const struct mei_cl_device_id mei_pse_tbl[] = {
+	{ MEI_PSE_DRIVER_NAME, MEI_UUID_PSE, MEI_CL_VERSION_ANY },
+
+	/* required last entry */
+	{ }
+};
+MODULE_DEVICE_TABLE(mei, mei_pse_tbl);
+
+static struct mei_cl_driver mei_pse_driver = {
+	.id_table = mei_pse_tbl,
+	.name = MEI_PSE_DRIVER_NAME,
+
+	.probe = mei_pse_probe,
+	.remove = mei_pse_remove,
+};
+
+static int __init mei_pse_init(void)
+{
+	int ret;
+
+	ret = mei_cldev_driver_register(&mei_pse_driver);
+	if (ret) {
+		pr_err("mei pse driver registration failed: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit mei_pse_exit(void)
+{
+	mei_cldev_driver_unregister(&mei_pse_driver);
+}
+
+module_init(mei_pse_init);
+module_exit(mei_pse_exit);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Device driver for Intel VSC PSE client");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/Kconfig
@@ -0,0 +1,28 @@
+#
+# Jesd204b support
+#
+
+config XILINX_JESD204B
+	tristate "Xilinx JESD204B"
+	help
+	  This option enables support for the Xilinx JESD204B driver.
+	  It is designed to allow user to access JESD204B IP registers
+	  with sysfs entries. JESD204B is the protocol used by High-Speed
+	  data converters to transfer data to FPGA/ASIC.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called jesd204b.
+
+config XILINX_JESD204B_PHY
+	tristate "JESD Phy Driver"
+	depends on XILINX_JESD204B
+	help
+	  This is JESD204b Phy Interface. It enables support for xilinx jesd204b phy
+	  controller.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called jesd204b_phy.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/Makefile
@@ -0,0 +1,5 @@
+obj-$(CONFIG_XILINX_JESD204B_PHY) += jesd204b_phy.o
+jesd204b_phy-y += jesd_phy.o gtx7s_cpll_bands.o \
+		gtx7s_qpll_bands.o
+obj-$(CONFIG_XILINX_JESD204B) += jesd204b.o
+jesd204b-y += xilinx_jesd204b.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/gtx7s_cpll_bands.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/gtx7s_cpll_bands.c
@@ -0,0 +1,88 @@
+/*
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/types.h>
+#include "s7_gtxe2_drp.h"
+#include "gtx7s_cpll_bands.h"
+
+static const u32 gtx7s_cpll_channel_address_lut
+			[GTX7S_CPLL_NUM_CHANNEL_DRP_REGS] = {
+	RXCDR_CFG0_ADDR,
+	RXCDR_CFG1_ADDR,
+	RXCDR_CFG2_ADDR,
+	RXCDR_CFG3_ADDR,
+	RXCDR_CFG4_ADDR,
+	RXOUT_DIV_ADDR,
+	TXOUT_DIV_ADDR,
+	RX_DFE_LPM_CFG_ADDR
+};
+
+static const u32 gtx7s_cpll_channel_offset_lut
+			[GTX7S_CPLL_NUM_CHANNEL_DRP_REGS] = {
+	RXCDR_CFG0_OFFSET,
+	RXCDR_CFG1_OFFSET,
+	RXCDR_CFG2_OFFSET,
+	RXCDR_CFG3_OFFSET,
+	RXCDR_CFG4_OFFSET,
+	RXOUT_DIV_OFFSET,
+	TXOUT_DIV_OFFSET,
+	RX_DFE_LPM_CFG_OFFSET
+};
+
+static const u32 gtx7s_cpll_channel_mask_lut
+			[GTX7S_CPLL_NUM_CHANNEL_DRP_REGS] = {
+	RXCDR_CFG0_MASK,
+	RXCDR_CFG1_MASK,
+	RXCDR_CFG2_MASK,
+	RXCDR_CFG3_MASK,
+	RXCDR_CFG4_MASK,
+	RXOUT_DIV_MASK,
+	TXOUT_DIV_MASK,
+	RX_DFE_LPM_CFG_MASK
+};
+
+/* Note bands run vertically from 1 to 4 */
+static const u16 gtx7s_cpll_channel_param_lut[GTX7S_CPLL_NUM_CHANNEL_DRP_REGS]
+			[GTX7S_CPLL_NUM_LINE_RATE_BANDS] = {
+	{0x20,	 0x20,		0x20,	0x20	},/*	 RXCDR_CFG0 */
+	{0x1010, 0x1020,	0x1040,	0x1040	},/*	 RXCDR_CFG1 */
+	{0x23ff, 0x23ff,	0x23ff,	0x23ff	},/*	 RXCDR_CFG2 */
+	{0x0,	 0x0,		0x0,	0x0	},/*	 RXCDR_CFG3 */
+	{0x3,	0x3,		0x3,	0x3	},/*	 RXCDR_CFG4 */
+	{0x3,	0x2,		0x1,	0x1	},/*	 RXOUT_DIV  */
+	{0x3,	0x2,		0x1,	0x1	},/*	TXOUT_DIV   */
+	{0x904,	0x904,		0x904,	0x104	} /*	RX_DFE_LPM_CFG */
+};
+
+u32 get_gtx7s_cpll_address_lut(u32 lut_address)
+{
+	return gtx7s_cpll_channel_address_lut[lut_address];
+}
+
+u32 get_gtx7s_cpll_offset_lut(u32 lut_address)
+{
+	return gtx7s_cpll_channel_offset_lut[lut_address];
+}
+
+u32 get_gtx7s_cpll_mask_lut(u32 lut_address)
+{
+	return gtx7s_cpll_channel_mask_lut[lut_address];
+}
+
+u16 get_gtx7s_cpll_param_lut(u32 param_address, u32 band_address)
+{
+	return gtx7s_cpll_channel_param_lut[param_address][band_address];
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/gtx7s_cpll_bands.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/gtx7s_cpll_bands.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/types.h>
+
+#ifndef GTX7S_CPLL_BANDS_H_
+#define GTX7S_CPLL_BANDS_H_
+
+#define GTX7S_CPLL_NUM_CHANNEL_DRP_REGS 8
+#define GTX7S_CPLL_NUM_LINE_RATE_BANDS 4
+
+u32 get_gtx7s_cpll_address_lut(u32);
+u32 get_gtx7s_cpll_offset_lut(u32);
+u32 get_gtx7s_cpll_mask_lut(u32);
+u16 get_gtx7s_cpll_param_lut(u32, u32);
+
+#endif /* GTX7S_CPLL_BANDS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/gtx7s_qpll_bands.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/gtx7s_qpll_bands.c
@@ -0,0 +1,96 @@
+/*
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/types.h>
+#include "s7_gtxe2_drp.h"
+#include "gtx7s_qpll_bands.h"
+
+static const u32 gtx7s_qpll_channel_address_lut
+			[GTX7S_QPLL_NUM_CHANNEL_DRP_REGS] = {
+	RXCDR_CFG0_ADDR,
+	RXCDR_CFG1_ADDR,
+	RXCDR_CFG2_ADDR,
+	RXCDR_CFG3_ADDR,
+	RXCDR_CFG4_ADDR,
+	RXOUT_DIV_ADDR,
+	TXOUT_DIV_ADDR,
+	RX_DFE_LPM_CFG_ADDR,
+	QPLL_CFG0_ADDR,
+	QPLL_CFG1_ADDR
+};
+
+static const u32 gtx7s_qpll_channel_offset_lut
+			[GTX7S_QPLL_NUM_CHANNEL_DRP_REGS] = {
+	RXCDR_CFG0_OFFSET,
+	RXCDR_CFG1_OFFSET,
+	RXCDR_CFG2_OFFSET,
+	RXCDR_CFG3_OFFSET,
+	RXCDR_CFG4_OFFSET,
+	RXOUT_DIV_OFFSET,
+	TXOUT_DIV_OFFSET,
+	RX_DFE_LPM_CFG_OFFSET,
+	QPLL_CFG0_OFFSET,
+	QPLL_CFG1_OFFSET
+};
+
+static const u32 gtx7s_qpll_channel_mask_lut
+			[GTX7S_QPLL_NUM_CHANNEL_DRP_REGS] = {
+	RXCDR_CFG0_MASK,
+	RXCDR_CFG1_MASK,
+	RXCDR_CFG2_MASK,
+	RXCDR_CFG3_MASK,
+	RXCDR_CFG4_MASK,
+	RXOUT_DIV_MASK,
+	TXOUT_DIV_MASK,
+	RX_DFE_LPM_CFG_MASK,
+	QPLL_CFG0_MASK,
+	QPLL_CFG1_MASK
+};
+
+/* Note bands run vertically from 1 to 10 */
+static const u16 gtx7s_qpll_channel_param_lut[GTX7S_QPLL_NUM_CHANNEL_DRP_REGS]
+			[GTX7S_QPLL_NUM_LINE_RATE_BANDS] = {
+{0x20,     0x20,   0x20,   0x20,     0x20,    0x20,    0x20,    0x20,    0x20,    0x20},/* RXCDR_CFG0 */
+{0x1008,   0x1010, 0x1020, 0x1010,   0x1020,  0x1040,  0x1020,  0x1040,  0x1040,  0x1040},/* RXCDR_CFG1 */
+{0x23ff,   0x23ff, 0x23ff, 0x23ff,   0x23ff,  0x23ff,  0x23ff,  0x23ff,  0x23ff,  0x23ff},/* RXCDR_CFG2 */
+{0x0,      0x0,    0x0,    0x0,      0x0,     0x0,     0x0,     0x0,     0x0,     0x0}, /* RXCDR_CFG3 */
+{0x3,      0x3,    0x3,    0x3,      0x3,     0x3,     0x3,     0x3,     0x3,     0x3},/* RXCDR_CFG4 */
+{0x3e8,    0x4,    0x2,    0x3,      0x2,     0x1,     0x2,     0x1,     0x1,     0x1},/* RXOUT_DIV  */
+{0x3e8,    0x4,    0x2,    0x3,      0x2,     0x1,     0x2,     0x1,     0x1,     0x1},/* TXOUT_DIV  */
+{0x904,    0x904,  0x904,  0x904,    0x904,   0x904,   0x904,   0x904,   0x104,   0x104},/* RX_DFE_LPM_CFG */
+{0x1c1,    0x1c1,  0x1c1,  0x181,    0x1c1,   0x1c1,   0x181,   0x1c1,   0x1c1,   0x181},/* QPLL_CFG0 */
+{0x68,     0x68,   0x68,   0x68,     0x68,    0x68,    0x68,    0x68,    0x68,    0x68} /* QPLL_CFG1 */
+};
+
+u32 get_gtx7s_qpll_address_lut(u32 lut_address)
+{
+	return gtx7s_qpll_channel_address_lut[lut_address];
+}
+
+u32 get_gtx7s_qpll_offset_lut(u32 lut_address)
+{
+	return gtx7s_qpll_channel_offset_lut[lut_address];
+}
+
+u32 get_gtx7s_qpll_mask_lut(u32 lut_address)
+{
+	return gtx7s_qpll_channel_mask_lut[lut_address];
+}
+
+u16 get_gtx7s_qpll_param_lut(u32 param_address, u32 band_address)
+{
+	return gtx7s_qpll_channel_param_lut[param_address][band_address];
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/gtx7s_qpll_bands.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/gtx7s_qpll_bands.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/types.h>
+
+#ifndef GTX7S_QPLL_BANDS_H_
+#define GTX7S_QPLL_BANDS_H_
+
+#define GTX7S_QPLL_NUM_CHANNEL_DRP_REGS 10
+#define GTX7S_QPLL_NUM_LINE_RATE_BANDS 10
+
+u32 get_gtx7s_qpll_address_lut(u32);
+u32 get_gtx7s_qpll_offset_lut(u32);
+u32 get_gtx7s_qpll_mask_lut(u32);
+u16 get_gtx7s_qpll_param_lut(u32, u32);
+
+#endif /* GTX7S_QPLL_BANDS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/jesd_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/jesd_phy.c
@@ -0,0 +1,384 @@
+/*
+ * Jesd204b phy support
+ *
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include "jesd_phy.h"
+#include "gtx7s_cpll_bands.h"
+#include "gtx7s_qpll_bands.h"
+
+#define PLATFORM_JESD204_PHY_ADDR 0x41E10000
+#define JESD_PHY_LOOP_OFF	0
+#define JESD_PHY_LOOP_PCS	1
+#define JESD_PHY_LOOP_PMA	2
+#define JESD_PHY_LOOP_MAX	2
+
+static inline void jesd204b_phy_write(struct jesd204b_phy_state *st,
+				      unsigned reg, unsigned val)
+{
+	iowrite32(val, st->phy + reg);
+}
+
+static inline unsigned int jesd204b_phy_read(struct jesd204b_phy_state *st,
+					     unsigned reg)
+{
+	return ioread32(st->phy + reg);
+}
+
+#define NUM_GT_CHANNELS	8
+
+#define QPLL	0x3 /* QPLL (7 series) QPLL1 (UltraScale) */
+#define QPLL0	0x2 /* (UltraScale Only) */
+#define CPLL	0x0
+
+#define DRPREAD  BIT(30)
+#define DRPWRITE BIT(31)
+
+#define NR_COMMON_DRP_INTERFACES 0x008
+#define NR_TRANS_DRP_INTERFACES 0x00C
+
+#define CHANNEL_DRP_BASE	0x200
+#define CHANNEL_DRP_ADDR	0x204
+#define CHANNEL_DRP_DREAD	0x20C
+#define CHANNEL_DRP_DWRITE	0x208
+#define CHANNEL_DRP_STAT	0x214
+
+#define CHANNEL_XCVR_SEL	0x400
+#define CHANNEL_XCVR_TXPLL	0x40C
+#define CHANNEL_XCVR_RXPLL	0x410
+#define CHANNEL_XCVR_LOOPB	0x41C
+
+static u32 read_channel_drp_reg(struct jesd204b_phy_state *st, u32 addr)
+{
+	u32 temp;
+
+	jesd204b_phy_write(st, CHANNEL_DRP_ADDR, (DRPREAD | addr));
+	temp = jesd204b_phy_read(st, CHANNEL_DRP_DREAD);
+	return temp;
+}
+
+static void write_channel_drp_reg(struct jesd204b_phy_state *st, u32 addr,
+				  u32 data)
+{
+	u32 loop = 10;
+
+	jesd204b_phy_write(st, CHANNEL_DRP_DWRITE, data);
+	jesd204b_phy_write(st, CHANNEL_DRP_ADDR, (DRPWRITE | addr));
+
+	do {
+		if (!jesd204b_phy_read(st, CHANNEL_DRP_STAT))
+			break;
+		msleep(1);
+	} while (loop--);
+
+	if (!loop)
+		dev_err(st->dev, "DRP wait timeout\n");
+}
+
+static void read_plls(struct jesd204b_phy_state *st)
+{
+	int i;
+	int pll = st->pll;
+	u32 no_of_common_drp_interfaces = 1;
+
+	if (st->pll == CPLL)
+		no_of_common_drp_interfaces = jesd204b_phy_read(
+						st, NR_TRANS_DRP_INTERFACES);
+	else
+		no_of_common_drp_interfaces = jesd204b_phy_read(
+						st, NR_COMMON_DRP_INTERFACES);
+
+	for (i = 0; i < no_of_common_drp_interfaces; i++) {
+		jesd204b_phy_write(st, CHANNEL_XCVR_SEL, i);
+		pll = jesd204b_phy_read(st, CHANNEL_XCVR_TXPLL);
+		pll = jesd204b_phy_read(st, CHANNEL_XCVR_RXPLL);
+	}
+}
+
+static void configure_plls(struct jesd204b_phy_state *st, u32 pll)
+{
+	int i;
+	u32 no_of_common_drp_interfaces;
+
+	if (pll == CPLL)
+		no_of_common_drp_interfaces = jesd204b_phy_read(
+						st, NR_TRANS_DRP_INTERFACES);
+	else
+		no_of_common_drp_interfaces = jesd204b_phy_read(
+						st, NR_COMMON_DRP_INTERFACES);
+
+	for (i = 0; i < no_of_common_drp_interfaces; i++) {
+		jesd204b_phy_write(st, CHANNEL_XCVR_SEL, i);
+		jesd204b_phy_write(st, CHANNEL_XCVR_TXPLL, pll);
+		jesd204b_phy_write(st, CHANNEL_XCVR_RXPLL, pll);
+	}
+}
+
+static void configure_channel_drp(struct jesd204b_phy_state *st, u32 setting)
+{
+	u32 i, j, addr, temp, no_of_common_drp_interfaces;
+	u32 no_channel_drp_reg = GTX7S_QPLL_NUM_CHANNEL_DRP_REGS;
+
+	no_of_common_drp_interfaces = jesd204b_phy_read(
+					st, NR_TRANS_DRP_INTERFACES);
+
+	if (st->pll == CPLL)
+		no_channel_drp_reg = GTX7S_CPLL_NUM_CHANNEL_DRP_REGS;
+	for (i = 0; i < no_of_common_drp_interfaces; i++) {
+		jesd204b_phy_write(st, CHANNEL_DRP_BASE, i);
+		for (j = 0; j < no_channel_drp_reg; j++) {
+			/* Get the register address */
+			if (st->pll == QPLL) {
+				addr = get_gtx7s_qpll_address_lut(j);
+
+				/* Read the register */
+				temp = read_channel_drp_reg(st, addr);
+
+				temp &= (0xFFFF ^ (get_gtx7s_qpll_mask_lut(j)));
+				temp |= ((get_gtx7s_qpll_param_lut(j, setting)
+						<< get_gtx7s_qpll_offset_lut(j))
+						& get_gtx7s_qpll_mask_lut(j));
+			} else {
+				addr = get_gtx7s_cpll_address_lut(j);
+
+				temp = read_channel_drp_reg(st, addr);
+
+				temp &= (0xFFFF ^ (get_gtx7s_cpll_mask_lut(j)));
+				temp |= ((get_gtx7s_cpll_param_lut(j, setting)
+						<< get_gtx7s_cpll_offset_lut(j))
+						& get_gtx7s_cpll_mask_lut(j));
+			}
+			write_channel_drp_reg(st, addr, temp);
+		}
+	}
+}
+
+void jesd204_phy_set_speed(struct jesd204b_phy_state *st, u32 band)
+{
+	/* make sure we have the correct PLL's selected. */
+	configure_channel_drp(st, band);
+}
+
+static void jesd204_phy_init(struct jesd204b_phy_state *st, int line_rate)
+{
+	jesd204_phy_set_speed(st, line_rate);
+}
+
+int jesd204_phy_set_loop(struct jesd204b_phy_state *st, u32 loopval)
+{
+	int i;
+	u32 no_of_channels;
+
+	no_of_channels = jesd204b_phy_read(st, NR_COMMON_DRP_INTERFACES);
+
+	if (loopval > JESD_PHY_LOOP_MAX)
+		return -EINVAL;
+
+	for (i = 0; i < no_of_channels ; i++) {
+		jesd204b_phy_write(st, CHANNEL_XCVR_SEL, i);
+		jesd204b_phy_write(st, CHANNEL_XCVR_LOOPB, loopval);
+	}
+	return 0;
+}
+
+static ssize_t jesd204b_pll_read(struct device *dev,
+				 struct device_attribute *attr,
+				 char *buf)
+{
+	struct jesd204b_phy_state *st = dev_get_drvdata(dev);
+
+	read_plls(st);
+	if (st->pll == CPLL)
+		return sprintf(buf, "cpll\n");
+	return sprintf(buf, "qpll\n");
+}
+
+static ssize_t jesd204b_configure_pll(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buf, size_t count)
+{
+	struct jesd204b_phy_state *st = dev_get_drvdata(dev);
+	unsigned val;
+	int ret;
+
+	ret = kstrtouint(buf, 0, &val);
+	if (!ret)
+		return 0;
+
+	if (val > QPLL) {
+		dev_err(dev, "Setting the pll to %d valid values\n"
+			      "00 = CPLL\n"
+			      "10 = QPLL0 (UltraScale Only)\n"
+			      "11 = QPLL (7 series) QPLL1 (UltraScale)\n", val);
+		return 0;
+	}
+	st->pll = val;
+	configure_plls(st, val);
+
+	return count;
+}
+
+static DEVICE_ATTR(configure_pll, S_IWUSR | S_IRUSR, jesd204b_pll_read,
+			jesd204b_configure_pll);
+
+static ssize_t jesd204b_linerate_read(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	struct jesd204b_phy_state *st = dev_get_drvdata(dev);
+
+	return sprintf(buf, "0x%X\n", st->band);
+}
+
+static ssize_t jesd204b_linerate_write(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t count)
+{
+	struct jesd204b_phy_state *st = dev_get_drvdata(dev);
+	int ret;
+	/* Low frequencies are not supported by qpll */
+
+	ret = kstrtouint(buf, 0, &st->band);
+	if (ret)
+		return ret;
+
+	dev_info(dev, "Setting the line rate to band to %d\n", st->band);
+	/* QPLL - freq options in phy
+	 * 62.5
+	 * 78.125
+	 * 94.697
+	 * 97.656
+	 * 125.000
+	 * 156.25
+	 * 187.5
+	 * 189.394
+	 * 195.313
+	 * 234.375
+	 * 250.000
+	 * 284.091
+	 * 292.969
+	 */
+	if (st->band == 2)
+		clk_set_rate(st->clk,  62500000); /* 2.5G */
+	else if (st->band == 4)
+		clk_set_rate(st->clk,  97656000); /* 3.9G */
+	else if (st->band == 6)
+		clk_set_rate(st->clk, 125000000); /* 5G */
+	else if (st->band == 7)
+		clk_set_rate(st->clk, 156250000); /* 6.25G */
+	else if (st->band == 8)
+		clk_set_rate(st->clk, 195313000); /* 7.812G */
+	else if (st->band == 9)
+		clk_set_rate(st->clk, 250000000);/* 10G */
+
+	jesd204_phy_init(st, st->band);
+
+	return count;
+}
+
+static DEVICE_ATTR(line_rate_band, S_IWUSR | S_IRUSR, jesd204b_linerate_read,
+		   jesd204b_linerate_write);
+
+/* Match table for of_platform binding */
+static const struct of_device_id jesd204b_phy_of_match[] = {
+	{ .compatible = "xlnx,jesd204-phy-2.0", },
+	{ /* end of list */ },
+};
+
+static int jesd204b_phy_probe(struct platform_device *pdev)
+{
+	struct jesd204b_phy_state *st;
+	struct resource *mem; /* IO mem resources */
+	int ret;
+	u32 ref_clk;
+
+	st = devm_kzalloc(&pdev->dev, sizeof(*st), GFP_KERNEL);
+	if (!st)
+		return -ENOMEM;
+
+	st->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(st->clk))
+		return -EPROBE_DEFER;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	st->phy = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(st->phy)) {
+		dev_err(&pdev->dev, "Failed ioremap\n");
+		return PTR_ERR(st->phy);
+	}
+	st->dev = &pdev->dev;
+	platform_set_drvdata(pdev, st);
+
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,lanes",
+				   &st->lanes);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to read required dt property\n");
+		return ret;
+	}
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,pll-selection",
+				   &st->pll);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to read required dt property\n");
+		return ret;
+	}
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,gt-refclk-freq",
+				   &ref_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to read required dt property\n");
+		return ret;
+	}
+
+	clk_set_rate(st->clk, (unsigned long)ref_clk);
+	device_create_file(&pdev->dev, &dev_attr_configure_pll);
+	device_create_file(&pdev->dev, &dev_attr_line_rate_band);
+
+	ret = clk_prepare_enable(st->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int jesd204b_phy_remove(struct platform_device *pdev)
+{
+	struct jesd204b_phy_state *st = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(st->clk);
+	clk_put(st->clk);
+	device_remove_file(&pdev->dev, &dev_attr_configure_pll);
+	device_remove_file(&pdev->dev, &dev_attr_line_rate_band);
+	return 0;
+}
+
+static struct platform_driver jesd204b_driver = {
+	.driver = {
+		.name = "jesd204b_phy",
+		.of_match_table = jesd204b_phy_of_match,
+	},
+	.probe		= jesd204b_phy_probe,
+	.remove		= jesd204b_phy_remove,
+};
+
+module_platform_driver(jesd204b_driver);
+
+MODULE_AUTHOR("Shubhrajyoti Datta <shubhraj@xilinx.com>");
+MODULE_DESCRIPTION("AXI-JESD204B Phy Interface Module");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/jesd_phy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/jesd_phy.h
@@ -0,0 +1,42 @@
+/*
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef JESD_PHY_H_
+#define JESD_PHY_H_
+
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+
+struct jesd204b_phy_state {
+	struct device	*dev;
+	void __iomem	*phy;
+	struct clk	*clk;
+	u32		vers_id;
+	u32		addr;
+	u32		lanes;
+	u32		band;
+	u32		pll;
+	unsigned long	rate;
+};
+
+int jesd204_phy_set_loop(struct jesd204b_phy_state *st, u32 loopval);
+
+#endif /* JESD_PHY_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/s7_gtxe2_drp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/s7_gtxe2_drp.h
@@ -0,0 +1,123 @@
+/*
+ * Copyright (C) 2014 - 2015 Xilinx, Inc.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#define TXOUT_DIV_ADDR					0x88
+#define TXOUT_DIV_MASK					0x70
+#define TXOUT_DIV_OFFSET				0x4
+#define TXOUT_DIV_WIDTH					0x3
+#define TXOUT_DIV_DEFAULT				0x0
+
+#define RXOUT_DIV_ADDR					0x88
+#define RXOUT_DIV_MASK					0x7
+#define RXOUT_DIV_OFFSET				0x0
+#define RXOUT_DIV_WIDTH					0x3
+#define RXOUT_DIV_DEFAULT				0x0
+
+#define RXCDR_CFG0_ADDR					0xa8
+#define RXCDR_CFG0_MASK					0xffff
+#define RXCDR_CFG0_OFFSET				0x0
+#define RXCDR_CFG0_WIDTH				0x10
+#define RXCDR_CFG0_DEFAULT				0x0
+
+#define RXCDR_CFG1_ADDR					0xa9
+#define RXCDR_CFG1_MASK					0xffff
+#define RXCDR_CFG1_OFFSET				0x0
+#define RXCDR_CFG1_WIDTH				0x10
+#define RXCDR_CFG1_DEFAULT				0x0
+
+#define RXCDR_CFG2_ADDR					0xaa
+#define RXCDR_CFG2_MASK					0xffff
+#define RXCDR_CFG2_OFFSET				0x0
+#define RXCDR_CFG2_WIDTH				0x10
+#define RXCDR_CFG2_DEFAULT				0x0
+
+#define RXCDR_CFG3_ADDR					0xab
+#define RXCDR_CFG3_MASK					0xffff
+#define RXCDR_CFG3_OFFSET				0x0
+#define RXCDR_CFG3_WIDTH				0x10
+#define RXCDR_CFG3_DEFAULT				0x0
+
+#define RXCDR_CFG4_ADDR					0xac
+#define RXCDR_CFG4_MASK					0xff
+#define RXCDR_CFG4_OFFSET				0x0
+#define RXCDR_CFG4_WIDTH				0x8
+#define RXCDR_CFG4_DEFAULT				0x0
+
+#define RX_DFE_LPM_CFG_ADDR				0x29
+#define RX_DFE_LPM_CFG_MASK				0xffff
+#define RX_DFE_LPM_CFG_OFFSET				0x0
+#define RX_DFE_LPM_CFG_WIDTH				0x10
+#define RX_DFE_LPM_CFG_DEFAULT				0x0
+
+#define QPLL_CFG0_ADDR					0x32
+#define QPLL_CFG0_MASK					0xffff
+#define QPLL_CFG0_OFFSET				0x0
+#define QPLL_CFG0_WIDTH					0x10
+#define QPLL_CFG0_DEFAULT				0x0
+
+#define QPLL_CFG1_ADDR					0x33
+#define QPLL_CFG1_MASK					0x7ff
+#define QPLL_CFG1_OFFSET				0x0
+#define QPLL_CFG1_WIDTH					0xb
+#define QPLL_CFG1_DEFAULT				0x0
+
+#define QPLL_REFCLK_DIV_M_ADDR				0x33
+#define QPLL_REFCLK_DIV_M_MASK				0xf800
+#define QPLL_REFCLK_DIV_M_OFFSET			0xb
+#define QPLL_REFCLK_DIV_M_WIDTH				0x5
+#define QPLL_REFCLK_DIV_M_DEFAULT			0x0
+
+#define QPLL_FBDIV_N_ADDR				0x36
+#define QPLL_FBDIV_N_MASK				0x3ff
+#define QPLL_FBDIV_N_OFFSET				0x0
+#define QPLL_FBDIV_N_WIDTH				0xa
+#define QPLL_FBDIV_N_DEFAULT				0x0
+
+#define QPLL_FBDIV_RATIO_ADDR				0x37
+#define QPLL_FBDIV_RATIO_MASK				0x40
+#define QPLL_FBDIV_RATIO_OFFSET				0x6
+#define QPLL_FBDIV_RATIO_WIDTH				0x1
+#define QPLL_FBDIV_RATIO_DEFAULT			0x0
+
+#define CPLL_CFG0_ADDR					0x5c
+#define CPLL_CFG0_MASK					0xff00
+#define CPLL_CFG0_OFFSET				0x8
+#define CPLL_CFG0_WIDTH					0x8
+#define CPLL_CFG0_DEFAULT				0x0
+
+#define CPLL_CFG1_ADDR					0x5d
+#define CPLL_CFG1_MASK					0xffff
+#define CPLL_CFG1_OFFSET				0x0
+#define CPLL_CFG1_WIDTH					0x10
+#define CPLL_CFG1_DEFAULT				0x0
+
+#define CPLL_REFCLK_DIV_M_ADDR				0x5e
+#define CPLL_REFCLK_DIV_M_MASK				0x1f00
+#define CPLL_REFCLK_DIV_M_OFFSET			0x8
+#define CPLL_REFCLK_DIV_M_WIDTH				0x5
+#define CPLL_REFCLK_DIV_M_DEFAULT			0x0
+
+#define CPLL_FB_DIV_45_N1_ADDR				0x5e
+#define CPLL_FB_DIV_45_N1_MASK				0x80
+#define CPLL_FB_DIV_45_N1_OFFSET			0x7
+#define CPLL_FB_DIV_45_N1_WIDTH				0x1
+#define CPLL_FB_DIV_45_N1_DEFAULT			0x0
+
+#define CPLL_FBDIV_N2_ADDR				0x5e
+#define CPLL_FBDIV_N2_MASK				0x7f
+#define CPLL_FBDIV_N2_OFFSET				0x0
+#define CPLL_FBDIV_N2_WIDTH				0x7
+#define CPLL_FBDIV_N2_DEFAULT				0x0
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/xilinx_jesd204b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/xilinx_jesd204b.c
@@ -0,0 +1,369 @@
+/*
+ * Xilinx AXI-JESD204B Interface Module
+ *
+ * Copyright 2014 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ *
+ * http://wiki.analog.com/resources/fpga/xilinx/
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/wait.h>
+
+#include "xilinx_jesd204b.h"
+
+struct child_clk {
+	struct clk_hw		hw;
+	struct jesd204b_state	*st;
+	unsigned long		rate;
+	bool			enabled;
+};
+
+#define to_clk_priv(_hw) container_of(_hw, struct child_clk, hw)
+
+static inline void jesd204b_write(struct jesd204b_state *st,
+				  unsigned int reg, unsigned int val)
+{
+	iowrite32(val, st->regs + reg);
+}
+
+static inline unsigned int jesd204b_read(struct jesd204b_state *st,
+					 unsigned int reg)
+{
+	return ioread32(st->regs + reg);
+}
+
+static ssize_t jesd204b_laneinfo_read(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf, unsigned int lane)
+{
+	struct jesd204b_state *st = dev_get_drvdata(dev);
+	int ret;
+	unsigned int val1, val2, val3;
+
+	val1 = jesd204b_read(st, XLNX_JESD204_REG_ID_L(lane));
+	val2 = jesd204b_read(st, XLNX_JESD204_REG_LANE_F(lane));
+	val3 = jesd204b_read(st, XLNX_JESD204_REG_SCR_S_HD_CF(lane));
+	ret = sprintf(buf,
+		      "DID: %d, BID: %d, LID: %d, L: %d, SCR: %d, F: %d\n",
+		      XLNX_JESD204_LANE_DID(val1),
+		      XLNX_JESD204_LANE_BID(val1),
+		      XLNX_JESD204_LANE_LID(val1),
+		      XLNX_JESD204_LANE_L(val1),
+		      XLNX_JESD204_LANE_SCR(val3),
+		      XLNX_JESD204_LANE_F(val2));
+
+	val1 = jesd204b_read(st, XLNX_JESD204_REG_LANE_K(lane));
+	val2 = jesd204b_read(st, XLNX_JESD204_REG_M_N_ND_CS(lane));
+
+	ret += sprintf(buf + ret,
+		       "K: %d, M: %d, N: %d, CS: %d, S: %d, N': %d, HD: %d\n",
+		       XLNX_JESD204_LANE_K(val1),
+		       XLNX_JESD204_LANE_M(val2),
+		       XLNX_JESD204_LANE_N(val2),
+		       XLNX_JESD204_LANE_CS(val2),
+		       XLNX_JESD204_LANE_S(val3),
+		       XLNX_JESD204_LANE_ND(val2),
+		       XLNX_JESD204_LANE_HD(val3));
+
+	val1 = jesd204b_read(st, XLNX_JESD204_REG_FCHK(lane));
+	ret += sprintf(buf + ret, "FCHK: 0x%X, CF: %d\n",
+		       XLNX_JESD204_LANE_FCHK(val1),
+		       XLNX_JESD204_LANE_CF(val3));
+
+	val1 = jesd204b_read(st, XLNX_JESD204_REG_SC2_ADJ_CTRL(lane));
+	val2 = jesd204b_read(st, XLNX_JESD204_REG_LANE_VERSION(lane));
+	ret += sprintf(buf + ret,
+		"ADJCNT: %d, PHYADJ: %d, ADJDIR: %d, JESDV: %d, SUBCLASS: %d\n",
+		       XLNX_JESD204_LANE_ADJ_CNT(val1),
+		       XLNX_JESD204_LANE_PHASE_ADJ_REQ(val1),
+		       XLNX_JESD204_LANE_ADJ_CNT_DIR(val1),
+		       XLNX_JESD204_LANE_JESDV(val2),
+		       XLNX_JESD204_LANE_SUBCLASS(val2));
+
+	ret += sprintf(buf + ret, "MFCNT : 0x%X\n",
+		       jesd204b_read(st, XLNX_JESD204_REG_TM_MFC_CNT(lane)));
+	ret += sprintf(buf + ret, "ILACNT: 0x%X\n",
+		       jesd204b_read(st, XLNX_JESD204_REG_TM_ILA_CNT(lane)));
+	ret += sprintf(buf + ret, "ERRCNT: 0x%X\n",
+		       jesd204b_read(st, XLNX_JESD204_REG_TM_ERR_CNT(lane)));
+	ret += sprintf(buf + ret, "BUFCNT: 0x%X\n",
+		       jesd204b_read(st, XLNX_JESD204_REG_TM_BUF_ADJ(lane)));
+	ret += sprintf(buf + ret, "LECNT: 0x%X\n",
+		       jesd204b_read(st,
+		       XLNX_JESD204_REG_TM_LINK_ERR_CNT(lane)));
+
+	ret += sprintf(buf + ret, "FC: %lu\n", st->rate);
+
+	return ret;
+}
+
+#define JESD_LANE(_x)							    \
+static ssize_t jesd204b_lane##_x##_info_read(struct device *dev,	    \
+					     struct device_attribute *attr, \
+					     char *buf)			    \
+{									    \
+	return jesd204b_laneinfo_read(dev, attr, buf, _x);		    \
+}									    \
+static DEVICE_ATTR(lane##_x##_info, 0400, jesd204b_lane##_x##_info_read, \
+		   NULL)
+
+JESD_LANE(0);
+JESD_LANE(1);
+JESD_LANE(2);
+JESD_LANE(3);
+JESD_LANE(4);
+JESD_LANE(5);
+JESD_LANE(6);
+JESD_LANE(7);
+
+static ssize_t jesd204b_lane_syscstat_read(struct device *dev,
+			struct device_attribute *attr,
+			char *buf, unsigned int lane)
+{
+	unsigned int stat;
+	struct jesd204b_state *st = dev_get_drvdata(dev);
+
+	stat = jesd204b_read(st, XLNX_JESD204_REG_SYNC_ERR_STAT);
+
+	return sprintf(buf,
+			"NOT_IN_TAB: %d, DISPARITY: %d, UNEXPECTED_K: %d\n",
+			stat & XLNX_JESD204_SYNC_ERR_NOT_IN_TAB(lane),
+			stat & XLNX_JESD204_SYNC_ERR_DISPARITY(lane),
+			stat & XLNX_JESD204_SYNC_ERR_UNEXPECTED_K(lane));
+}
+
+#define JESD_SYNCSTAT_LANE(_x)						       \
+static ssize_t jesd204b_lane##_x##_syncstat_read(struct device *dev,	       \
+						 struct device_attribute *attr,\
+						 char *buf)		       \
+{									       \
+	return jesd204b_lane_syscstat_read(dev, attr, buf, _x);		       \
+}									       \
+static DEVICE_ATTR(lane##_x##_syncstat, 0400,			       \
+		   jesd204b_lane##_x##_syncstat_read, NULL)
+
+JESD_SYNCSTAT_LANE(0);
+JESD_SYNCSTAT_LANE(1);
+JESD_SYNCSTAT_LANE(2);
+JESD_SYNCSTAT_LANE(3);
+JESD_SYNCSTAT_LANE(4);
+JESD_SYNCSTAT_LANE(5);
+JESD_SYNCSTAT_LANE(6);
+JESD_SYNCSTAT_LANE(7);
+
+static ssize_t jesd204b_reg_write(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t count)
+{
+	struct jesd204b_state *st = dev_get_drvdata(dev);
+	unsigned int val;
+	int ret;
+
+	ret = sscanf(buf, "%i %i", &st->addr, &val);
+	if (ret == 2)
+		jesd204b_write(st, st->addr, val);
+
+	return count;
+}
+
+static ssize_t jesd204b_reg_read(struct device *dev,
+				 struct device_attribute *attr,
+				 char *buf)
+{
+	struct jesd204b_state *st = dev_get_drvdata(dev);
+
+	return sprintf(buf, "0x%X\n", jesd204b_read(st, st->addr));
+}
+
+static DEVICE_ATTR(reg_access, 0600, jesd204b_reg_read,
+		   jesd204b_reg_write);
+
+static ssize_t jesd204b_syncreg_read(struct device *dev,
+				     struct device_attribute *attr,
+				     char *buf)
+{
+	struct jesd204b_state *st = dev_get_drvdata(dev);
+
+	return sprintf(buf, "0x%X\n", jesd204b_read(st,
+					XLNX_JESD204_REG_SYNC_STATUS));
+}
+
+static DEVICE_ATTR(sync_status, 0400, jesd204b_syncreg_read, NULL);
+
+/* Match table for of_platform binding */
+static const struct of_device_id jesd204b_of_match[] = {
+	{ .compatible = "xlnx,jesd204-5.1",},
+	{ .compatible = "xlnx,jesd204-5.2",},
+	{ .compatible = "xlnx,jesd204-6.1",},
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, jesd204b_of_match);
+
+static int jesd204b_probe(struct platform_device *pdev)
+{
+	struct jesd204b_state *st;
+	struct resource *mem; /* IO mem resources */
+	struct clk *clk;
+	struct child_clk *clk_priv;
+	struct clk_init_data init;
+	unsigned int val;
+	int ret;
+
+	clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return -EPROBE_DEFER;
+
+	st = devm_kzalloc(&pdev->dev, sizeof(*st), GFP_KERNEL);
+	if (!st)
+		return -ENOMEM;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	st->regs = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(st->regs)) {
+		dev_err(&pdev->dev, "Failed ioremap\n");
+		return PTR_ERR(st->regs);
+	}
+
+	st->dev = &pdev->dev;
+
+	platform_set_drvdata(pdev, st);
+
+	st->clk = clk;
+	clk_set_rate(st->clk, 156250000);
+	st->rate = clk_get_rate(clk);
+
+	of_property_read_u32(pdev->dev.of_node, "xlnx,node-is-transmit",
+			     &st->transmit);
+
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,lanes",
+				   &st->lanes);
+	if (ret)
+		st->lanes = jesd204b_read(st, XLNX_JESD204_REG_LANES) + 1;
+
+	jesd204b_write(st, XLNX_JESD204_REG_RESET, XLNX_JESD204_RESET);
+	while (!jesd204b_read(st, XLNX_JESD204_REG_RESET))
+		msleep(20);
+
+	jesd204b_write(st, XLNX_JESD204_REG_ILA_CTRL,
+		       (of_property_read_bool(pdev->dev.of_node,
+			"xlnx,lanesync-enable") ? XLNX_JESD204_ILA_EN : 0));
+
+	jesd204b_write(st, XLNX_JESD204_REG_SCR_CTRL,
+		       (of_property_read_bool(pdev->dev.of_node,
+			"xlnx,scramble-enable") ? XLNX_JESD204_SCR_EN : 0));
+
+	jesd204b_write(st, XLNX_JESD204_REG_SYSREF_CTRL,
+		       (of_property_read_bool(pdev->dev.of_node,
+			"xlnx,sysref-always-enable") ?
+			XLNX_JESD204_ALWAYS_SYSREF_EN : 0));
+
+	device_create_file(&pdev->dev, &dev_attr_reg_access);
+
+	device_create_file(&pdev->dev, &dev_attr_sync_status);
+	switch (st->lanes) {
+	case 8:
+		device_create_file(&pdev->dev, &dev_attr_lane4_info);
+		device_create_file(&pdev->dev, &dev_attr_lane5_info);
+		device_create_file(&pdev->dev, &dev_attr_lane6_info);
+		device_create_file(&pdev->dev, &dev_attr_lane7_info);
+		if (!st->transmit) {
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane4_syncstat);
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane5_syncstat);
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane6_syncstat);
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane7_syncstat);
+		}
+		fallthrough;
+	case 4:
+		device_create_file(&pdev->dev, &dev_attr_lane2_info);
+		device_create_file(&pdev->dev, &dev_attr_lane3_info);
+		if (!st->transmit) {
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane2_syncstat);
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane3_syncstat);
+		}
+		fallthrough;
+	case 2:
+		device_create_file(&pdev->dev, &dev_attr_lane1_info);
+		if (!st->transmit)
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane1_syncstat);
+		fallthrough;
+	case 1:
+		device_create_file(&pdev->dev, &dev_attr_lane0_info);
+		if (!st->transmit)
+			device_create_file(&pdev->dev,
+					   &dev_attr_lane0_syncstat);
+		break;
+	default:
+
+		break;
+	}
+
+	clk_priv = devm_kzalloc(&pdev->dev, sizeof(*clk_priv), GFP_KERNEL);
+	if (!clk_priv)
+		return -ENOMEM;
+
+	/* struct child_clk assignments */
+	clk_priv->hw.init = &init;
+	clk_priv->rate = st->rate;
+	clk_priv->st = st;
+
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return ret;
+	}
+	val = jesd204b_read(st, XLNX_JESD204_REG_VERSION);
+
+	dev_info(&pdev->dev,
+		 "AXI-JESD204B %d.%d Rev %d, at 0x%08llX mapped to 0x%p",
+		 XLNX_JESD204_VERSION_MAJOR(val),
+		 XLNX_JESD204_VERSION_MINOR(val),
+		 XLNX_JESD204_VERSION_REV(val),
+		 (unsigned long long)mem->start, st->regs);
+
+	return 0;
+}
+
+static int jesd204b_remove(struct platform_device *pdev)
+{
+	struct jesd204b_state *st = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(st->clk);
+	clk_put(st->clk);
+
+	return 0;
+}
+
+static struct platform_driver jesd204b_driver = {
+	.driver = {
+		.name = KBUILD_MODNAME,
+		.of_match_table = jesd204b_of_match,
+	},
+	.probe		= jesd204b_probe,
+	.remove		= jesd204b_remove,
+};
+
+module_platform_driver(jesd204b_driver);
+
+MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>");
+MODULE_DESCRIPTION("Analog Devices AXI-JESD204B Interface Module");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/jesd204b/xilinx_jesd204b.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/jesd204b/xilinx_jesd204b.h
@@ -0,0 +1,135 @@
+/*
+ * Xilinx AXI-JESD204B v5.1 Interface Module
+ *
+ * Copyright 2014 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ *
+ * http://wiki.analog.com/resources/fpga/xilinx/
+ */
+
+#ifndef XILINX_JESD204B_H_
+#define XILINX_JESD204B_H_
+
+struct jesd204b_state {
+	struct device	*dev;
+	void __iomem	*regs;
+	void __iomem	*phy;
+	struct clk	*clk;
+	u32		lanes;
+	u32		vers_id;
+	u32		addr;
+	u32		band;
+	u32		transmit;
+	u32		pll;
+	unsigned long	rate;
+};
+
+#define XLNX_JESD204_REG_VERSION		0x000
+#define XLNX_JESD204_VERSION_MAJOR(x)		(((x) >> 24) & 0xFF)
+#define XLNX_JESD204_VERSION_MINOR(x)		(((x) >> 16) & 0xFF)
+#define XLNX_JESD204_VERSION_REV(x)		(((x) >> 8) & 0xFF)
+
+#define XLNX_JESD204_REG_RESET			0x004
+#define XLNX_JESD204_RESET			(1 << 0)
+
+#define XLNX_JESD204_REG_ILA_CTRL		0x008
+#define XLNX_JESD204_ILA_EN			(1 << 0)
+
+#define XLNX_JESD204_REG_SCR_CTRL		0x00C
+#define XLNX_JESD204_SCR_EN			(1 << 0)
+
+#define XLNX_JESD204_REG_SYSREF_CTRL		0x010
+#define XLNX_JESD204_ALWAYS_SYSREF_EN		(1 << 0)
+
+#define XLNX_JESD204_REG_ILA_MFC		0x014
+#define XLNX_JESD204_ILA_MFC(x)			(((x) - 1) & 0xFF)
+						/* TX only 4..256 */
+
+#define XLNX_JESD204_REG_TEST_MODE_SEL		0x018
+#define XLNX_JESD204_TEST_MODE_OFF		0 /* Normal operation */
+#define XLNX_JESD204_TEST_MODE_K28_5		1 /* Send/Receive /K28.5/
+						   * indefinitely
+						   */
+#define XLNX_JESD204_TEST_MODE_ILA		2 /* Synchronize as normal then
+						   * send/receive repeated ILA
+						   * sequences
+						   */
+#define XLNX_JESD204_TEST_MODE_D21_5		3 /* Send/Receive /D21.5/
+						   * indefinitely
+						   */
+#define XLNX_JESD204_TEST_MODE_RPAT		5 /* Send/Receive modified
+						   * random pattern (RPAT)
+						   */
+#define XLNX_JESD204_TEST_MODE_JSPAT		7 /* Send/Receive a scrambled
+						   * jitter pattern (JSPAT)
+						   */
+
+#define XLNX_JESD204_REG_SYNC_STATUS		0x038 /* Link SYNC status */
+#define XLNX_JESD204_REG_SYNC_ERR_STAT		0x01C /* RX only */
+#define XLNX_JESD204_SYNC_ERR_NOT_IN_TAB(lane)		(1 << (0 + (lane) * 3))
+#define XLNX_JESD204_SYNC_ERR_DISPARITY(lane)		(1 << (1 + (lane) * 3))
+#define XLNX_JESD204_SYNC_ERR_UNEXPECTED_K(lane)	(1 << (2 + (lane) * 3))
+
+#define XLNX_JESD204_REG_OCTETS_PER_FRAME	0x020
+#define XLNX_JESD204_OCTETS_PER_FRAME(x)	(((x) - 1) & 0xFF) /* 1..256 */
+
+#define XLNX_JESD204_REG_FRAMES_PER_MFRAME	0x024
+#define XLNX_JESD204_FRAMES_PER_MFRAME(x)	(((x) - 1) & 0x1F) /* 1..32 */
+
+#define XLNX_JESD204_REG_LANES			0x028
+#define XLNX_JESD204_LANES(x)			(((x) - 1) & 0x1F) /* 1..32 */
+
+#define XLNX_JESD204_REG_SUBCLASS		0x02C
+
+#define XLNX_JESD204_REG_RX_BUF_DELAY		0x030 /* RX only */
+#define XLNX_JESD204_RX_BUF_DELAY(x)		((x) & 0x1FFF)
+
+#define XLNX_JESD204_REG_RX_LINK_CTRL		0x034 /* RX only */
+#define XLNX_JESD204_LINK_TEST_EN		(1 << 0)
+#define XLNX_JESD204_SYNC_ERR_REP_DIS		(1 << 8)
+
+/* Per LANE Registers */
+#define XLNX_JESD204_REG_LANE_VERSION(l)	(0x800 + ((l) * 0x40))
+#define XLNX_JESD204_LANE_SUBCLASS(x)		(((x) >> 0) & 0x7)
+#define XLNX_JESD204_LANE_JESDV(x)		(((x) >> 8) & 0x7)
+
+#define XLNX_JESD204_REG_LANE_F(l)		(0x804 + ((l) * 0x40))
+#define XLNX_JESD204_LANE_F(x)			((((x) >> 0) & 0xFF) + 1)
+
+#define XLNX_JESD204_REG_LANE_K(l)		(0x808 + ((l) * 0x40))
+#define XLNX_JESD204_LANE_K(x)			((((x) >> 0) & 0x1F) + 1)
+
+#define XLNX_JESD204_REG_ID_L(l)		(0x80C + ((l) * 0x40))
+#define XLNX_JESD204_LANE_DID(x)		(((x) >> 0) & 0xFF)
+#define XLNX_JESD204_LANE_BID(x)		(((x) >> 8) & 0x1F)
+#define XLNX_JESD204_LANE_LID(x)		(((x) >> 16) & 0x1F)
+#define XLNX_JESD204_LANE_L(x)			((((x) >> 24) & 0x1F) + 1)
+
+#define XLNX_JESD204_REG_M_N_ND_CS(l)		(0x810 + ((l) * 0x40))
+#define XLNX_JESD204_LANE_M(x)			((((x) >> 0) & 0xFF) + 1)
+#define XLNX_JESD204_LANE_N(x)			((((x) >> 8) & 0x1F) + 1)
+#define XLNX_JESD204_LANE_ND(x)			((((x) >> 16) & 0x1F) + 1)
+#define XLNX_JESD204_LANE_CS(x)			(((x) >> 24) & 0x3)
+
+#define XLNX_JESD204_REG_SCR_S_HD_CF(l)		(0x814 + ((l) * 0x40))
+#define XLNX_JESD204_LANE_SCR(x)		(((x) >> 0) & 0x1)
+#define XLNX_JESD204_LANE_S(x)			((((x) >> 8) & 0x1F) + 1)
+#define XLNX_JESD204_LANE_HD(x)			(((x) >> 16) & 0x1)
+#define XLNX_JESD204_LANE_CF(x)			(((x) >> 24) & 0x1F)
+
+#define XLNX_JESD204_REG_FCHK(l)		(0x818 + ((l) * 0x40))
+#define XLNX_JESD204_LANE_FCHK(x)		(((x) >> 16) & 0xFF)
+
+#define XLNX_JESD204_REG_SC2_ADJ_CTRL(l)	(0x81C + ((l) * 0x40))
+#define XLNX_JESD204_LANE_ADJ_CNT(x)		(((x) >> 0) & 0xF)
+#define XLNX_JESD204_LANE_PHASE_ADJ_REQ(x)	(((x) >> 8) & 0x1)
+#define XLNX_JESD204_LANE_ADJ_CNT_DIR(x)		(((x) >> 16) & 0x1)
+
+#define XLNX_JESD204_REG_TM_ERR_CNT(l)		(0x820 + ((l) * 0x40))
+#define XLNX_JESD204_REG_TM_LINK_ERR_CNT(l)	(0x824 + ((l) * 0x40))
+#define XLNX_JESD204_REG_TM_ILA_CNT(l)		(0x828 + ((l) * 0x40))
+#define XLNX_JESD204_REG_TM_MFC_CNT(l)		(0x82C + ((l) * 0x40))
+#define XLNX_JESD204_REG_TM_BUF_ADJ(l)		(0x830 + ((l) * 0x40))
+
+#endif /* ADI_JESD204B_V51_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/kgdbts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/kgdbts.c
@@ -1070,10 +1070,10 @@
 {
 	if (strlen(opt) >= MAX_CONFIG_LEN) {
 		printk(KERN_ERR "kgdbts: config string too long\n");
-		return -ENOSPC;
+		return 1;
 	}
 	strcpy(config, opt);
-	return 0;
+	return 1;
 }
 
 __setup("kgdbts=", kgdbts_option_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/lattice-ecp3-config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/lattice-ecp3-config.c
@@ -76,12 +76,12 @@
 
 	if (fw == NULL) {
 		dev_err(&spi->dev, "Cannot load firmware, aborting\n");
-		return;
+		goto out;
 	}
 
 	if (fw->size == 0) {
 		dev_err(&spi->dev, "Error: Firmware size is 0!\n");
-		return;
+		goto out;
 	}
 
 	/* Fill dummy data (24 stuffing bits for commands) */
@@ -103,7 +103,7 @@
 		dev_err(&spi->dev,
 			"Error: No supported FPGA detected (JEDEC_ID=%08x)!\n",
 			jedec_id);
-		return;
+		goto out;
 	}
 
 	dev_info(&spi->dev, "FPGA %s detected\n", ecp3_dev[i].name);
@@ -116,7 +116,7 @@
 	buffer = kzalloc(fw->size + 8, GFP_KERNEL);
 	if (!buffer) {
 		dev_err(&spi->dev, "Error: Can't allocate memory!\n");
-		return;
+		goto out;
 	}
 
 	/*
@@ -155,7 +155,7 @@
 			"Error: Timeout waiting for FPGA to clear (status=%08x)!\n",
 			status);
 		kfree(buffer);
-		return;
+		goto out;
 	}
 
 	dev_info(&spi->dev, "Configuring the FPGA...\n");
@@ -181,7 +181,7 @@
 	release_firmware(fw);
 
 	kfree(buffer);
-
+out:
 	complete(&data->fw_loaded);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/lkdtm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/lkdtm/Makefile
@@ -20,7 +20,7 @@
 
 OBJCOPYFLAGS :=
 OBJCOPYFLAGS_rodata_objcopy.o	:= \
-			--rename-section .noinstr.text=.rodata,alloc,readonly,load
+			--rename-section .noinstr.text=.rodata,alloc,readonly,load,contents
 targets += rodata.o rodata_objcopy.o
 $(obj)/rodata_objcopy.o: $(obj)/rodata.o FORCE
 	$(call if_changed,objcopy)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/lkdtm/bugs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/lkdtm/bugs.c
@@ -29,7 +29,7 @@
 #if defined(CONFIG_FRAME_WARN) && (CONFIG_FRAME_WARN > 0)
 #define REC_STACK_SIZE (_AC(CONFIG_FRAME_WARN, UL) / 2)
 #else
-#define REC_STACK_SIZE (THREAD_SIZE / 8)
+#define REC_STACK_SIZE (THREAD_SIZE / 8UL)
 #endif
 #define REC_NUM_DEFAULT ((THREAD_SIZE / REC_STACK_SIZE) * 2)
 
@@ -248,6 +248,11 @@
 
 	not_checked = kmalloc(sizeof(*not_checked) * 2, GFP_KERNEL);
 	checked = kmalloc(sizeof(*checked) * 2, GFP_KERNEL);
+	if (!not_checked || !checked) {
+		kfree(not_checked);
+		kfree(checked);
+		return;
+	}
 
 	pr_info("Array access within bounds ...\n");
 	/* For both, touch all bytes in the actual member size. */
@@ -267,7 +272,10 @@
 	kfree(not_checked);
 	kfree(checked);
 	pr_err("FAIL: survived array bounds overflow!\n");
-	pr_expected_config(CONFIG_UBSAN_BOUNDS);
+	if (IS_ENABLED(CONFIG_UBSAN_BOUNDS))
+		pr_expected_config(CONFIG_UBSAN_TRAP);
+	else
+		pr_expected_config(CONFIG_UBSAN_BOUNDS);
 }
 
 void lkdtm_CORRUPT_LIST_ADD(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/lkdtm/lkdtm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/lkdtm/lkdtm.h
@@ -9,19 +9,19 @@
 extern char *lkdtm_kernel_info;
 
 #define pr_expected_config(kconfig)				\
-{								\
+do {								\
 	if (IS_ENABLED(kconfig)) 				\
 		pr_err("Unexpected! This %s was built with " #kconfig "=y\n", \
 			lkdtm_kernel_info);			\
 	else							\
 		pr_warn("This is probably expected, since this %s was built *without* " #kconfig "=y\n", \
 			lkdtm_kernel_info);			\
-}
+} while (0)
 
 #ifndef MODULE
 int lkdtm_check_bool_cmdline(const char *param);
 #define pr_expected_config_param(kconfig, param)		\
-{								\
+do {								\
 	if (IS_ENABLED(kconfig)) {				\
 		switch (lkdtm_check_bool_cmdline(param)) {	\
 		case 0:						\
@@ -52,7 +52,7 @@
 			break;					\
 		}						\
 	}							\
-}
+} while (0)
 #else
 #define pr_expected_config_param(kconfig, param) pr_expected_config(kconfig)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/lkdtm/usercopy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/lkdtm/usercopy.c
@@ -30,12 +30,12 @@
  */
 static noinline unsigned char *trick_compiler(unsigned char *stack)
 {
-	return stack + 0;
+	return stack + unconst;
 }
 
 static noinline unsigned char *do_usercopy_stack_callee(int value)
 {
-	unsigned char buf[32];
+	unsigned char buf[128];
 	int i;
 
 	/* Exercise stack to avoid everything living in registers. */
@@ -43,7 +43,12 @@
 		buf[i] = value & 0xff;
 	}
 
-	return trick_compiler(buf);
+	/*
+	 * Put the target buffer in the middle of stack allocation
+	 * so that we don't step on future stack users regardless
+	 * of stack growth direction.
+	 */
+	return trick_compiler(&buf[(128/2)-32]);
 }
 
 static noinline void do_usercopy_stack(bool to_user, bool bad_frame)
@@ -66,6 +71,12 @@
 		bad_stack -= sizeof(unsigned long);
 	}
 
+#ifdef ARCH_HAS_CURRENT_STACK_POINTER
+	pr_info("stack     : %px\n", (void *)current_stack_pointer);
+#endif
+	pr_info("good_stack: %px-%px\n", good_stack, good_stack + sizeof(good_stack));
+	pr_info("bad_stack : %px-%px\n", bad_stack, bad_stack + sizeof(good_stack));
+
 	user_addr = vm_mmap(NULL, 0, PAGE_SIZE,
 			    PROT_READ | PROT_WRITE | PROT_EXEC,
 			    MAP_ANONYMOUS | MAP_PRIVATE, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/Kconfig
@@ -46,4 +46,11 @@
 	  Supported SoCs:
 	  Intel Bay Trail
 
+config INTEL_MEI_VSC
+	tristate "Intel Vision Sensing Controller device with ME interface"
+	select INTEL_MEI
+	depends on X86 && SPI
+	help
+	  MEI over SPI for Intel Vision Sensing Controller device
+
 source "drivers/misc/mei/hdcp/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/Makefile
@@ -22,6 +22,10 @@
 mei-txe-objs := pci-txe.o
 mei-txe-objs += hw-txe.o
 
+obj-$(CONFIG_INTEL_MEI_VSC) += mei-vsc.o
+mei-vsc-objs := spi-vsc.o
+mei-vsc-objs += hw-vsc.o
+
 mei-$(CONFIG_EVENT_TRACING) += mei-trace.o
 CFLAGS_mei-trace.o = -I$(src)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/bus-fixup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/bus-fixup.c
@@ -175,7 +175,7 @@
 	ret = __mei_cl_send(cldev->cl, (u8 *)&req, sizeof(req), 0,
 			    MEI_CL_IO_TX_BLOCKING);
 	if (ret < 0) {
-		dev_err(&cldev->dev, "Could not send ReqFWVersion cmd\n");
+		dev_err(&cldev->dev, "Could not send ReqFWVersion cmd ret = %d\n", ret);
 		return ret;
 	}
 
@@ -187,7 +187,7 @@
 		 * Should be at least one version block,
 		 * error out if nothing found
 		 */
-		dev_err(&cldev->dev, "Could not read FW version\n");
+		dev_err(&cldev->dev, "Could not read FW version ret = %d\n", bytes_recv);
 		return -EIO;
 	}
 
@@ -337,7 +337,7 @@
 	ret = __mei_cl_send(cl, (u8 *)&cmd, sizeof(cmd), 0,
 			    MEI_CL_IO_TX_BLOCKING);
 	if (ret < 0) {
-		dev_err(bus->dev, "Could not send IF version cmd\n");
+		dev_err(bus->dev, "Could not send IF version cmd ret = %d\n", ret);
 		return ret;
 	}
 
@@ -352,7 +352,7 @@
 	bytes_recv = __mei_cl_recv(cl, (u8 *)reply, if_version_length, &vtag,
 				   0, 0);
 	if (bytes_recv < 0 || (size_t)bytes_recv < if_version_length) {
-		dev_err(bus->dev, "Could not read IF version\n");
+		dev_err(bus->dev, "Could not read IF version ret = %d\n", bytes_recv);
 		ret = -EIO;
 		goto err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/client.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/client.c
@@ -1975,7 +1975,7 @@
 
 	mei_hdr = mei_msg_hdr_init(cb);
 	if (IS_ERR(mei_hdr)) {
-		rets = -PTR_ERR(mei_hdr);
+		rets = PTR_ERR(mei_hdr);
 		mei_hdr = NULL;
 		goto err;
 	}
@@ -1999,7 +1999,7 @@
 
 	hbuf_slots = mei_hbuf_empty_slots(dev);
 	if (hbuf_slots < 0) {
-		rets = -EOVERFLOW;
+		buf_len = -EOVERFLOW;
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/hbm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/hbm.c
@@ -672,10 +672,14 @@
 	if (!cl)
 		return;
 
-	dev_dbg(dev->dev, "cl dma map result = %d\n", res->status);
-	cl->status = res->status;
-	if (!cl->status)
+	if (res->status) {
+		dev_err(dev->dev, "cl dma map failed %d\n", res->status);
+		cl->status = -EFAULT;
+	} else {
+		dev_dbg(dev->dev, "cl dma map succeeded\n");
 		cl->dma_mapped = 1;
+		cl->status = 0;
+	}
 	wake_up(&cl->wait);
 }
 
@@ -698,10 +702,14 @@
 	if (!cl)
 		return;
 
-	dev_dbg(dev->dev, "cl dma unmap result = %d\n", res->status);
-	cl->status = res->status;
-	if (!cl->status)
+	if (res->status) {
+		dev_err(dev->dev, "cl dma unmap failed %d\n", res->status);
+		cl->status = -EFAULT;
+	} else {
+		dev_dbg(dev->dev, "cl dma unmap succeeded\n");
 		cl->dma_mapped = 0;
+		cl->status = 0;
+	}
 	wake_up(&cl->wait);
 }
 
@@ -1343,7 +1351,8 @@
 
 		if (dev->dev_state != MEI_DEV_INIT_CLIENTS ||
 		    dev->hbm_state != MEI_HBM_CAP_SETUP) {
-			if (dev->dev_state == MEI_DEV_POWER_DOWN) {
+			if (dev->dev_state == MEI_DEV_POWER_DOWN ||
+			    dev->dev_state == MEI_DEV_POWERING_DOWN) {
 				dev_dbg(dev->dev, "hbm: capabilities response: on shutdown, ignoring\n");
 				return 0;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/hdcp/mei_hdcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/hdcp/mei_hdcp.c
@@ -859,8 +859,8 @@
 		dev_warn(&cldev->dev, "mei_cldev_disable() failed\n");
 }
 
-#define MEI_UUID_HDCP GUID_INIT(0xB638AB7E, 0x94E2, 0x4EA2, 0xA5, \
-				0x52, 0xD1, 0xC5, 0x4B, 0x62, 0x7F, 0x04)
+#define MEI_UUID_HDCP UUID_LE(0xB638AB7E, 0x94E2, 0x4EA2, 0xA5, \
+			      0x52, 0xD1, 0xC5, 0x4B, 0x62, 0x7F, 0x04)
 
 static const struct mei_cl_device_id mei_hdcp_tbl[] = {
 	{ .uuid = MEI_UUID_HDCP, .version = MEI_CL_VERSION_ANY },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/hw-me-regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/hw-me-regs.h
@@ -107,6 +107,17 @@
 #define MEI_DEV_ID_ADP_S      0x7AE8  /* Alder Lake Point S */
 #define MEI_DEV_ID_ADP_LP     0x7A60  /* Alder Lake Point LP */
 #define MEI_DEV_ID_ADP_P      0x51E0  /* Alder Lake Point P */
+#define MEI_DEV_ID_ADP_N      0x54E0  /* Alder Lake Point N */
+
+#define MEI_DEV_ID_RPL_S      0x7A68  /* Raptor Lake Point S */
+
+#define MEI_DEV_ID_MTL_M      0x7E70  /* Meteor Lake Point M */
+#define MEI_DEV_ID_ARL_S      0x7F68  /* Arrow Lake Point S */
+#define MEI_DEV_ID_ARL_H      0x7770  /* Arrow Lake Point H */
+
+#define MEI_DEV_ID_LNL_M      0xA870  /* Lunar Lake Point M */
+
+#define MEI_DEV_ID_PTL_P      0xE470  /* Panther Lake P */
 
 /*
  * MEI HW Section
@@ -120,6 +131,7 @@
 #define PCI_CFG_HFS_2         0x48
 #define PCI_CFG_HFS_3         0x60
 #  define PCI_CFG_HFS_3_FW_SKU_MSK   0x00000070
+#  define PCI_CFG_HFS_3_FW_SKU_IGN   0x00000000
 #  define PCI_CFG_HFS_3_FW_SKU_SPS   0x00000060
 #define PCI_CFG_HFS_4         0x64
 #define PCI_CFG_HFS_5         0x68
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/hw-me.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/hw-me.c
@@ -1405,16 +1405,16 @@
 	.quirk_probe = mei_me_fw_type_sps_4
 
 /**
- * mei_me_fw_type_sps() - check for sps sku
+ * mei_me_fw_type_sps_ign() - check for sps or ign sku
  *
- * Read ME FW Status register to check for SPS Firmware.
- * The SPS FW is only signaled in pci function 0
+ * Read ME FW Status register to check for SPS or IGN Firmware.
+ * The SPS/IGN FW is only signaled in pci function 0
  *
  * @pdev: pci device
  *
- * Return: true in case of SPS firmware
+ * Return: true in case of SPS/IGN firmware
  */
-static bool mei_me_fw_type_sps(const struct pci_dev *pdev)
+static bool mei_me_fw_type_sps_ign(const struct pci_dev *pdev)
 {
 	u32 reg;
 	u32 fw_type;
@@ -1427,14 +1427,15 @@
 
 	dev_dbg(&pdev->dev, "fw type is %d\n", fw_type);
 
-	return fw_type == PCI_CFG_HFS_3_FW_SKU_SPS;
+	return fw_type == PCI_CFG_HFS_3_FW_SKU_IGN ||
+	       fw_type == PCI_CFG_HFS_3_FW_SKU_SPS;
 }
 
 #define MEI_CFG_KIND_ITOUCH                     \
 	.kind = "itouch"
 
-#define MEI_CFG_FW_SPS                          \
-	.quirk_probe = mei_me_fw_type_sps
+#define MEI_CFG_FW_SPS_IGN                      \
+	.quirk_probe = mei_me_fw_type_sps_ign
 
 #define MEI_CFG_FW_VER_SUPP                     \
 	.fw_ver_supported = 1
@@ -1535,7 +1536,7 @@
 	MEI_CFG_PCH8_HFS,
 	MEI_CFG_FW_VER_SUPP,
 	MEI_CFG_DMA_128,
-	MEI_CFG_FW_SPS,
+	MEI_CFG_FW_SPS_IGN,
 };
 
 /* Cannon Lake itouch with quirk for SPS 5.0 and newer Firmware exclusion
@@ -1545,7 +1546,7 @@
 	MEI_CFG_KIND_ITOUCH,
 	MEI_CFG_PCH8_HFS,
 	MEI_CFG_FW_VER_SUPP,
-	MEI_CFG_FW_SPS,
+	MEI_CFG_FW_SPS_IGN,
 };
 
 /* Tiger Lake and newer devices */
@@ -1562,7 +1563,7 @@
 	MEI_CFG_FW_VER_SUPP,
 	MEI_CFG_DMA_128,
 	MEI_CFG_TRC,
-	MEI_CFG_FW_SPS,
+	MEI_CFG_FW_SPS_IGN,
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/hw-vsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/hw-vsc.c
@@ -0,0 +1,1634 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021, Intel Corporation. All rights reserved.
+ * Intel Management Engine Interface (Intel MEI) Linux driver
+ */
+#include <linux/crc32.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/interrupt.h>
+#include <linux/kthread.h>
+#include <linux/pci.h>
+#include <linux/pm_runtime.h>
+#include <linux/sizes.h>
+#include <linux/swap.h>
+#include <linux/types.h>
+
+#include "hw-vsc.h"
+
+static int spi_dev_xfer(struct mei_vsc_hw *hw, void *out_data, void *in_data,
+			int len)
+{
+	hw->xfer.tx_buf = out_data;
+	hw->xfer.rx_buf = in_data;
+	hw->xfer.len = len;
+
+	spi_message_init_with_transfers(&hw->msg, &hw->xfer, 1);
+	return spi_sync_locked(hw->spi, &hw->msg);
+}
+
+#define SPI_XFER_PACKET_CRC(pkt) (*(u32 *)(pkt->buf + pkt->hdr.len))
+static int spi_validate_packet(struct mei_vsc_hw *hw,
+			       struct spi_xfer_packet *pkt)
+{
+	u32 base_crc;
+	u32 crc;
+	struct spi_xfer_hdr *hdr = &pkt->hdr;
+
+	base_crc = SPI_XFER_PACKET_CRC(pkt);
+	crc = ~crc32(~0, (u8 *)pkt, sizeof(struct spi_xfer_hdr) + pkt->hdr.len);
+
+	if (base_crc != crc) {
+		dev_err(&hw->spi->dev, "%s crc error cmd %x 0x%x 0x%x\n",
+			__func__, hdr->cmd, base_crc, crc);
+		return -EINVAL;
+	}
+
+	if (hdr->cmd == CMD_SPI_FATAL_ERR) {
+		dev_err(&hw->spi->dev,
+			"receive fatal error from FW cmd %d %d %d.\nCore dump: %s\n",
+			hdr->cmd, hdr->seq, hw->seq, (char *)pkt->buf);
+		return -EIO;
+	} else if (hdr->cmd == CMD_SPI_NACK || hdr->cmd == CMD_SPI_BUSY ||
+		   hdr->seq != hw->seq) {
+		dev_err(&hw->spi->dev, "receive error from FW cmd %d %d %d\n",
+			hdr->cmd, hdr->seq, hw->seq);
+		return -EAGAIN;
+	}
+
+	return 0;
+}
+
+static inline bool spi_rom_xfer_asserted(struct mei_vsc_hw *hw)
+{
+	return gpiod_get_value_cansleep(hw->wakeuphost);
+}
+
+static inline bool spi_xfer_asserted(struct mei_vsc_hw *hw)
+{
+	return atomic_read(&hw->lock_cnt) > 0 &&
+	       gpiod_get_value_cansleep(hw->wakeuphost);
+}
+
+static void spi_xfer_lock(struct mei_vsc_hw *hw)
+{
+	gpiod_set_value_cansleep(hw->wakeupfw, 0);
+}
+
+static void spi_xfer_unlock(struct mei_vsc_hw *hw)
+{
+	atomic_dec_if_positive(&hw->lock_cnt);
+	gpiod_set_value_cansleep(hw->wakeupfw, 1);
+}
+
+static bool spi_xfer_locked(struct mei_vsc_hw *hw)
+{
+	return !gpiod_get_value_cansleep(hw->wakeupfw);
+}
+
+static bool spi_need_read(struct mei_vsc_hw *hw)
+{
+	return spi_xfer_asserted(hw) && !spi_xfer_locked(hw);
+}
+
+#define WAIT_FW_ASSERTED_TIMEOUT (2 * HZ)
+static int spi_xfer_wait_asserted(struct mei_vsc_hw *hw)
+{
+	wait_event_timeout(hw->xfer_wait, spi_xfer_asserted(hw),
+			   WAIT_FW_ASSERTED_TIMEOUT);
+
+	dev_dbg(&hw->spi->dev, "%s %d %d %d\n", __func__,
+		atomic_read(&hw->lock_cnt),
+		gpiod_get_value_cansleep(hw->wakeupfw),
+		gpiod_get_value_cansleep(hw->wakeuphost));
+	if (!spi_xfer_asserted(hw))
+		return -ETIME;
+	else
+		return 0;
+}
+
+static int spi_wakeup_request(struct mei_vsc_hw *hw)
+{
+	/* wakeup spi slave and wait for response */
+	spi_xfer_lock(hw);
+	return spi_xfer_wait_asserted(hw);
+}
+
+static void spi_wakeup_release(struct mei_vsc_hw *hw)
+{
+	return spi_xfer_unlock(hw);
+}
+
+static int find_sync_byte(u8 *buf, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		if (buf[i] == PACKET_SYNC)
+			return i;
+
+	return -1;
+}
+
+#define PACKET_PADDING_SIZE 1
+#define MAX_XFER_COUNT 5
+static int mei_vsc_xfer_internal(struct mei_vsc_hw *hw,
+				 struct spi_xfer_packet *pkt,
+				 struct spi_xfer_packet *ack_pkt)
+{
+	u8 *rx_buf = hw->rx_buf1;
+	u8 *tx_buf = hw->tx_buf1;
+	int next_xfer_len = PACKET_SIZE(pkt) + XFER_TIMEOUT_BYTES;
+	int offset = 0;
+	bool synced = false;
+	int len;
+	int count_down = MAX_XFER_COUNT;
+	int ret = 0;
+	int i;
+
+	dev_dbg(&hw->spi->dev, "spi tx pkt begin: %s %d %d\n", __func__,
+		spi_xfer_asserted(hw), gpiod_get_value_cansleep(hw->wakeupfw));
+	memcpy(tx_buf, pkt, PACKET_SIZE(pkt));
+	memset(rx_buf, 0, MAX_XFER_BUFFER_SIZE);
+
+	do {
+		dev_dbg(&hw->spi->dev,
+			"spi tx pkt partial ing: %s %d %d %d %d\n", __func__,
+			spi_xfer_asserted(hw),
+			gpiod_get_value_cansleep(hw->wakeupfw), next_xfer_len,
+			synced);
+
+		count_down--;
+		ret = spi_dev_xfer(hw, tx_buf, rx_buf, next_xfer_len);
+		if (ret)
+			return ret;
+
+		memset(tx_buf, 0, MAX_XFER_BUFFER_SIZE);
+		if (!synced) {
+			i = find_sync_byte(rx_buf, next_xfer_len);
+			if (i >= 0) {
+				synced = true;
+				len = next_xfer_len - i;
+			} else {
+				continue;
+			}
+
+		} else {
+			i = 0;
+			len = min_t(int, next_xfer_len,
+				    sizeof(*ack_pkt) - offset);
+		}
+
+		memcpy(&ack_pkt[offset], &rx_buf[i], len);
+		offset += len;
+
+		if (offset >= sizeof(ack_pkt->hdr))
+			next_xfer_len = PACKET_SIZE(ack_pkt) - offset +
+					PACKET_PADDING_SIZE;
+
+	} while (next_xfer_len > 0 && count_down > 0);
+
+	dev_dbg(&hw->spi->dev, "spi tx pkt done: %s %d %d cmd %d %d %d %d\n",
+		__func__, next_xfer_len, count_down, ack_pkt->hdr.sync,
+		ack_pkt->hdr.cmd, ack_pkt->hdr.len, ack_pkt->hdr.seq);
+
+	if (next_xfer_len > 0)
+		return -EAGAIN;
+
+	return spi_validate_packet(hw, ack_pkt);
+}
+
+static int mei_vsc_xfer(struct mei_vsc_hw *hw, u8 cmd, void *tx, u32 tx_len,
+			void *rx, int rx_max_len, u32 *rx_len)
+{
+	struct spi_xfer_packet *pkt;
+	struct spi_xfer_packet *ack_pkt;
+	u32 *crc;
+	int ret;
+
+	if (!tx || !rx || tx_len > MAX_SPI_MSG_SIZE)
+		return -EINVAL;
+
+	if (rx_len)
+		*rx_len = 0;
+
+	pkt = kzalloc(sizeof(*pkt) + sizeof(*ack_pkt), GFP_KERNEL);
+	ack_pkt = pkt + 1;
+	if (!pkt || !ack_pkt)
+		return -ENOMEM;
+
+	pkt->hdr.sync = PACKET_SYNC;
+	pkt->hdr.cmd = cmd;
+	pkt->hdr.seq = ++hw->seq;
+	pkt->hdr.len = tx_len;
+
+	memcpy(pkt->buf, tx, tx_len);
+	crc = (u32 *)(pkt->buf + tx_len);
+	*crc = ~crc32(~0, (u8 *)pkt, sizeof(pkt->hdr) + tx_len);
+
+	mutex_lock(&hw->mutex);
+
+	ret = spi_wakeup_request(hw);
+	if (ret) {
+		dev_err(&hw->spi->dev, "wakeup vsc FW failed\n");
+		goto out;
+	}
+
+	ret = mei_vsc_xfer_internal(hw, pkt, ack_pkt);
+	if (ret)
+		goto out;
+
+	if (ack_pkt->hdr.len > 0) {
+		int len;
+
+		len = (ack_pkt->hdr.len < rx_max_len) ? ack_pkt->hdr.len :
+							      rx_max_len;
+		memcpy(rx, ack_pkt->buf, len);
+		if (rx_len)
+			*rx_len = len;
+	}
+
+out:
+	spi_wakeup_release(hw);
+	mutex_unlock(&hw->mutex);
+	kfree(pkt);
+	return ret;
+}
+
+static int mei_vsc_read_raw(struct mei_vsc_hw *hw, u8 *buf, u32 max_len,
+			    u32 *len)
+{
+	struct host_timestamp ts = { 0 };
+
+	ts.realtime = ktime_to_ns(ktime_get_real());
+	ts.boottime = ktime_to_ns(ktime_get_boottime());
+
+	return mei_vsc_xfer(hw, CMD_SPI_READ, &ts, sizeof(ts), buf, max_len,
+			    len);
+}
+
+static int mei_vsc_write_raw(struct mei_vsc_hw *hw, u8 *buf, u32 len)
+{
+	u8 status = 0;
+	int rx_len;
+
+	return mei_vsc_xfer(hw, CMD_SPI_WRITE, buf, len, &status,
+			    sizeof(status), &rx_len);
+}
+
+#define LOADER_XFER_RETRY_COUNT 25
+static int spi_rom_dev_xfer(struct mei_vsc_hw *hw, void *out_data,
+			    void *in_data, int len)
+{
+	int ret;
+	int i;
+	u32 *tmp = out_data;
+	int retry = 0;
+
+	if (len % 4 != 0)
+		return -EINVAL;
+
+	for (i = 0; i < len / 4; i++)
+		tmp[i] = ___constant_swab32(tmp[i]);
+
+	mutex_lock(&hw->mutex);
+	while (retry < LOADER_XFER_RETRY_COUNT) {
+		if (!spi_rom_xfer_asserted(hw))
+			break;
+
+		msleep(20);
+		retry++;
+	}
+
+	if (retry >= LOADER_XFER_RETRY_COUNT) {
+		dev_err(&hw->spi->dev, "%s retry %d times gpio %d\n", __func__,
+			retry, spi_rom_xfer_asserted(hw));
+		mutex_unlock(&hw->mutex);
+		return -EAGAIN;
+	}
+
+	ret = spi_dev_xfer(hw, out_data, in_data, len);
+	mutex_unlock(&hw->mutex);
+	if (!in_data || ret)
+		return ret;
+
+	tmp = in_data;
+	for (i = 0; i < len / 4; i++)
+		tmp[i] = ___constant_swab32(tmp[i]);
+
+	return 0;
+}
+
+#define VSC_RESET_PIN_TOGGLE_INTERVAL 20
+#define VSC_ROM_BOOTUP_DELAY_TIME 10
+static int vsc_reset(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	gpiod_set_value_cansleep(hw->resetfw, 1);
+	msleep(VSC_RESET_PIN_TOGGLE_INTERVAL);
+	gpiod_set_value_cansleep(hw->resetfw, 0);
+	msleep(VSC_RESET_PIN_TOGGLE_INTERVAL);
+	gpiod_set_value_cansleep(hw->resetfw, 1);
+	msleep(VSC_ROM_BOOTUP_DELAY_TIME);
+	/* set default host wake pin to 1, which try to avoid unexpected host irq interrupt */
+	gpiod_set_value_cansleep(hw->wakeupfw, 1);
+	return 0;
+}
+
+/* %s is sensor name, need to be get and format in runtime */
+static char *fw_name_template[][3] = {
+	{
+		"vsc/soc_a1/ivsc_fw_a1.bin",
+		"vsc/soc_a1/ivsc_pkg_%s_0_a1.bin",
+		"vsc/soc_a1/ivsc_skucfg_%s_0_1_a1.bin",
+	},
+	{
+		"vsc/soc_a1_prod/ivsc_fw_a1_prod.bin",
+		"vsc/soc_a1_prod/ivsc_pkg_%s_0_a1_prod.bin",
+		"vsc/soc_a1_prod/ivsc_skucfg_%s_0_1_a1_prod.bin",
+	},
+};
+
+static int check_silicon(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct vsc_rom_master_frame *frame =
+		(struct vsc_rom_master_frame *)hw->fw.tx_buf;
+	struct vsc_rom_slave_token *token =
+		(struct vsc_rom_slave_token *)hw->fw.rx_buf;
+	int ret;
+	u32 efuse1;
+	u32 strap;
+
+	dev_dbg(dev->dev, "%s size %zu %zu\n", __func__, sizeof(*frame),
+		sizeof(*token));
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_DUMP_MEM;
+
+	frame->data.dump_mem.addr = EFUSE1_ADDR;
+	frame->data.dump_mem.len = 4;
+
+	ret = spi_rom_dev_xfer(hw, frame, token, VSC_ROM_SPI_PKG_SIZE);
+	if (ret || token->token == VSC_TOKEN_ERROR) {
+		dev_err(dev->dev, "%s %d %d %d\n", __func__, __LINE__, ret,
+			token->token);
+		return ret;
+	}
+
+	memset(frame, 0, sizeof(*frame));
+	memset(token, 0, sizeof(*token));
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_RESERVED;
+	ret = spi_rom_dev_xfer(hw, frame, token, VSC_ROM_SPI_PKG_SIZE);
+	if (ret || token->token == VSC_TOKEN_ERROR ||
+	    token->token != VSC_TOKEN_DUMP_RESP) {
+		dev_err(dev->dev, "%s %d %d %d\n", __func__, __LINE__, ret,
+			token->token);
+		return -EIO;
+	}
+
+	efuse1 = *(u32 *)token->payload;
+	dev_dbg(dev->dev, "%s efuse1=%d\n", __func__, efuse1);
+
+	/* to check the silicon main and sub version */
+	hw->fw.main_ver = (efuse1 >> SI_MAINSTEPPING_VERSION_OFFSET) &
+			  SI_MAINSTEPPING_VERSION_MASK;
+	hw->fw.sub_ver = (efuse1 >> SI_SUBSTEPPING_VERSION_OFFSET) &
+			 SI_SUBSTEPPING_VERSION_MASK;
+	if (hw->fw.main_ver != SI_MAINSTEPPING_VERSION_A) {
+		dev_err(dev->dev, "%s:  silicon main version error(%d)\n",
+			__func__, hw->fw.main_ver);
+		return -EINVAL;
+	}
+	if (hw->fw.sub_ver != SI_SUBSTEPPING_VERSION_0 &&
+	    hw->fw.sub_ver != SI_SUBSTEPPING_VERSION_1) {
+		dev_dbg(dev->dev, "%s: silicon sub version error(%d)\n", __func__,
+			hw->fw.sub_ver);
+		return -EINVAL;
+	}
+
+	/* to get the silicon strap key: debug or production ? */
+	memset(frame, 0, sizeof(*frame));
+	memset(token, 0, sizeof(*token));
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_DUMP_MEM;
+	frame->data.dump_mem.addr = STRAP_ADDR;
+	frame->data.dump_mem.len = 4;
+
+	ret = spi_rom_dev_xfer(hw, frame, token, VSC_ROM_SPI_PKG_SIZE);
+	if (ret || token->token == VSC_TOKEN_ERROR) {
+		dev_err(dev->dev, "%s: transfer failed or invalid token\n",
+			__func__);
+		return ret;
+	}
+
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_RESERVED;
+	ret = spi_rom_dev_xfer(hw, frame, token, VSC_ROM_SPI_PKG_SIZE);
+	if (ret || token->token == VSC_TOKEN_ERROR ||
+	    token->token != VSC_TOKEN_DUMP_RESP) {
+		dev_err(dev->dev,
+			"%s: transfer failed or invalid token-> (token = %d)\n",
+			__func__, token->token);
+		return -EINVAL;
+	}
+
+	dev_dbg(dev->dev,
+		"%s:  getting the memory(0x%0x), step 2 payload: 0x%0x\n",
+		__func__, STRAP_ADDR, *(u32 *)token->payload);
+
+	strap = *(u32 *)token->payload;
+	dev_dbg(dev->dev, "%s:  strap = 0x%x\n", __func__, strap);
+
+	/* to check the silicon strap key source */
+	hw->fw.key_src =
+		(strap >> SI_STRAP_KEY_SRC_OFFSET) & SI_STRAP_KEY_SRC_MASK;
+
+	dev_dbg(dev->dev, "%s: silicon version check done: %s%s\n", __func__,
+		hw->fw.sub_ver == SI_SUBSTEPPING_VERSION_0 ? "A0" : "A1",
+		hw->fw.key_src == SI_STRAP_KEY_SRC_DEBUG ? "" : "-prod");
+	if (hw->fw.sub_ver == SI_SUBSTEPPING_VERSION_1) {
+		if (hw->fw.key_src == SI_STRAP_KEY_SRC_DEBUG) {
+			snprintf(hw->fw.fw_file_name,
+				 sizeof(hw->fw.fw_file_name),
+				 fw_name_template[0][0]);
+			snprintf(hw->fw.sensor_file_name,
+				 sizeof(hw->fw.sensor_file_name),
+				 fw_name_template[0][1], hw->cam_sensor_name);
+			snprintf(hw->fw.sku_cnf_file_name,
+				 sizeof(hw->fw.sku_cnf_file_name),
+				 fw_name_template[0][2], hw->cam_sensor_name);
+		} else {
+			snprintf(hw->fw.fw_file_name,
+				 sizeof(hw->fw.fw_file_name),
+				 fw_name_template[1][0]);
+			snprintf(hw->fw.sensor_file_name,
+				 sizeof(hw->fw.sensor_file_name),
+				 fw_name_template[1][1], hw->cam_sensor_name);
+			snprintf(hw->fw.sku_cnf_file_name,
+				 sizeof(hw->fw.sku_cnf_file_name),
+				 fw_name_template[1][2], hw->cam_sensor_name);
+		}
+	}
+
+	return 0;
+}
+
+static int parse_main_fw(struct mei_device *dev, const struct firmware *fw)
+{
+	struct bootloader_sign *bootloader = NULL;
+	struct firmware_sign *arc_sem = NULL;
+	struct firmware_sign *em7d = NULL;
+	struct firmware_sign *ace_run = NULL;
+	struct firmware_sign *ace_vis = NULL;
+	struct firmware_sign *ace_conf = NULL;
+	struct vsc_boot_img *img = (struct vsc_boot_img *)fw->data;
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct manifest *man = NULL;
+	struct fragment *bootl_frag = &hw->fw.frags[BOOT_IMAGE_TYPE];
+	struct fragment *arcsem_frag = &hw->fw.frags[ARC_SEM_IMG_TYPE];
+	struct fragment *acer_frag = &hw->fw.frags[ACER_IMG_TYPE];
+	struct fragment *acev_frag = &hw->fw.frags[ACEV_IMG_TYPE];
+	struct fragment *acec_frag = &hw->fw.frags[ACEC_IMG_TYPE];
+	struct fragment *em7d_frag = &hw->fw.frags[EM7D_IMG_TYPE];
+	struct firmware_sign *firmwares[IMG_CNT_MAX];
+	int i;
+
+	if (!img || img->magic != VSC_FILE_MAGIC) {
+		dev_err(dev->dev, "image file error\n");
+		return -EINVAL;
+	}
+
+	if (img->image_count < IMG_BOOT_ARC_EM7D ||
+	    img->image_count > IMG_CNT_MAX) {
+		dev_err(dev->dev, "%s: image count error: image_count=0x%x\n",
+			__func__, img->image_count);
+		return -EINVAL;
+	}
+
+	dev_dbg(dev->dev, "%s: img->image_count=%d\n", __func__,
+		img->image_count);
+
+	/* only two lower bytes are used */
+	hw->fw.fw_option = img->option & 0xFFFF;
+	/* image not include bootloader */
+	hw->fw.fw_cnt = img->image_count - 1;
+
+	bootloader =
+		(struct bootloader_sign *)(img->image_loc + img->image_count);
+	if ((u8 *)bootloader > (fw->data + fw->size))
+		return -EINVAL;
+
+	if (bootloader->magic != VSC_FW_MAGIC) {
+		dev_err(dev->dev,
+			"bootloader signed magic error! magic number 0x%08x, image size 0x%08x\n",
+			bootloader->magic, bootloader->image_size);
+		return -EINVAL;
+	}
+
+	man = (struct manifest *)((char *)bootloader->image +
+				  bootloader->image_size - SIG_SIZE -
+				  sizeof(struct manifest) - CSSHEADER_SIZE);
+	if (man->svn == MAX_SVN_VALUE)
+		hw->fw.svn = MAX_SVN_VALUE;
+	else if (hw->fw.svn == 0)
+		hw->fw.svn = man->svn;
+
+	dev_dbg(dev->dev, "%s: svn: 0x%08X", __func__, hw->fw.svn);
+	/* currently only support silicon versoin A0 | A1 */
+	if ((hw->fw.sub_ver == SI_SUBSTEPPING_VERSION_0 &&
+	     hw->fw.svn != MAX_SVN_VALUE) ||
+	    (hw->fw.sub_ver == SI_SUBSTEPPING_VERSION_1 &&
+	     hw->fw.svn == MAX_SVN_VALUE)) {
+		dev_err(dev->dev,
+			"silicon version and image svn not matched(A%s:0x%x)\n",
+			hw->fw.sub_ver == SI_SUBSTEPPING_VERSION_0 ? "0" : "1",
+			hw->fw.svn);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < img->image_count - 1; i++) {
+		if (i == 0) {
+			firmwares[i] =
+				(struct firmware_sign *)(bootloader->image +
+							 bootloader->image_size);
+			dev_dbg(dev->dev,
+				"FW (%d/%d) magic number 0x%08x, image size 0x%08x\n",
+				i, img->image_count, firmwares[i]->magic,
+				firmwares[i]->image_size);
+			continue;
+		}
+
+		firmwares[i] =
+			(struct firmware_sign *)(firmwares[i - 1]->image +
+						 firmwares[i - 1]->image_size);
+
+		if ((u8 *)firmwares[i] > fw->data + fw->size)
+			return -EINVAL;
+
+		dev_dbg(dev->dev,
+			"FW (%d/%d) magic number 0x%08x, image size 0x%08x\n", i,
+			img->image_count, firmwares[i]->magic,
+			firmwares[i]->image_size);
+		if (firmwares[i]->magic != VSC_FW_MAGIC) {
+			dev_err(dev->dev,
+				"FW (%d/%d) magic error! magic number 0x%08x, image size 0x%08x\n",
+				i, img->image_count, firmwares[i]->magic,
+				firmwares[i]->image_size);
+
+			return -EINVAL;
+		}
+	}
+
+	arc_sem = firmwares[0];
+	if (img->image_count >= IMG_BOOT_ARC_EM7D)
+		em7d = firmwares[img->image_count - 2];
+
+	if (img->image_count >= IMG_BOOT_ARC_ACER_EM7D)
+		ace_run = firmwares[1];
+
+	if (img->image_count >= IMG_BOOT_ARC_ACER_ACEV_EM7D)
+		ace_vis = firmwares[2];
+
+	if (img->image_count >= IMG_BOOT_ARC_ACER_ACEV_ACECNF_EM7D)
+		ace_conf = firmwares[3];
+
+	bootl_frag->data = bootloader->image;
+	bootl_frag->size = bootloader->image_size;
+	bootl_frag->location = img->image_loc[0];
+	if (!bootl_frag->location)
+		return -EINVAL;
+
+	if (!arc_sem)
+		return -EINVAL;
+	arcsem_frag->data = arc_sem->image;
+	arcsem_frag->size = arc_sem->image_size;
+	arcsem_frag->location = img->image_loc[1];
+	if (!arcsem_frag->location)
+		return -EINVAL;
+
+	if (ace_run) {
+		acer_frag->data = ace_run->image;
+		acer_frag->size = ace_run->image_size;
+		acer_frag->location = img->image_loc[2];
+		if (!acer_frag->location)
+			return -EINVAL;
+
+		if (ace_vis) {
+			acev_frag->data = ace_vis->image;
+			acev_frag->size = ace_vis->image_size;
+			/* Align to 4K boundary */
+			acev_frag->location = ((acer_frag->location +
+						acer_frag->size + 0xFFF) &
+					       ~(0xFFF));
+			if (img->image_loc[3] &&
+			    acer_frag->location != img->image_loc[3]) {
+				dev_err(dev->dev,
+					"ACE vision image location error. img->image_loc[3] = 0x%x, calculated is 0x%x\n",
+					img->image_loc[3], acev_frag->location);
+				/* when location mismatch, use the one from image file. */
+				acev_frag->location = img->image_loc[3];
+			}
+		}
+
+		if (ace_conf) {
+			acec_frag->data = ace_conf->image;
+			acec_frag->size = ace_conf->image_size;
+			/* Align to 4K boundary */
+			acec_frag->location = ((acev_frag->location +
+						acev_frag->size + 0xFFF) &
+					       ~(0xFFF));
+			if (img->image_loc[4] &&
+			    acec_frag->location != img->image_loc[4]) {
+				dev_err(dev->dev,
+					"ACE vision image location error. img->image_loc[4] = 0x%x, calculated is 0x%x\n",
+					img->image_loc[4], acec_frag->location);
+				/* when location mismatch, use the one from image file. */
+				acec_frag->location = img->image_loc[4];
+			}
+		}
+	}
+
+	em7d_frag->data = em7d->image;
+	em7d_frag->size = em7d->image_size;
+	/* em7d is the last firmware */
+	em7d_frag->location = img->image_loc[img->image_count - 1];
+	if (!em7d_frag->location)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int parse_sensor_fw(struct mei_device *dev, const struct firmware *fw)
+{
+	struct firmware_sign *ace_vis = NULL;
+	struct firmware_sign *ace_conf = NULL;
+	struct vsc_boot_img *img = (struct vsc_boot_img *)fw->data;
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct fragment *acer_frag = &hw->fw.frags[ACER_IMG_TYPE];
+	struct fragment *acev_frag = &hw->fw.frags[ACEV_IMG_TYPE];
+	struct fragment *acec_frag = &hw->fw.frags[ACEC_IMG_TYPE];
+
+	if (!img || img->magic != VSC_FILE_MAGIC ||
+	    img->image_count < IMG_ACEV_ACECNF ||
+	    img->image_count > IMG_CNT_MAX)
+		return -EINVAL;
+
+	dev_dbg(dev->dev, "%s: img->image_count=%d\n", __func__,
+		img->image_count);
+
+	hw->fw.fw_cnt += img->image_count;
+	if (hw->fw.fw_cnt > IMG_CNT_MAX)
+		return -EINVAL;
+
+	ace_vis = (struct firmware_sign *)(img->image_loc + img->image_count);
+	ace_conf =
+		(struct firmware_sign *)(ace_vis->image + ace_vis->image_size);
+
+	dev_dbg(dev->dev,
+		"ACE vision signed magic number 0x%08x, image size 0x%08x\n",
+		ace_vis->magic, ace_vis->image_size);
+	if (ace_vis->magic != VSC_FW_MAGIC) {
+		dev_err(dev->dev,
+			"ACE vision signed magic error! magic number 0x%08x, image size 0x%08x\n",
+			ace_vis->magic, ace_vis->image_size);
+		return -EINVAL;
+	}
+
+	acev_frag->data = ace_vis->image;
+	acev_frag->size = ace_vis->image_size;
+	/* Align to 4K boundary */
+	acev_frag->location =
+		((acer_frag->location + acer_frag->size + 0xFFF) & ~(0xFFF));
+	if (img->image_loc[0] && acer_frag->location != img->image_loc[0]) {
+		dev_err(dev->dev,
+			"ACE vision image location error. img->image_loc[0] = 0x%x, calculated is 0x%x\n",
+			img->image_loc[0], acev_frag->location);
+		/* when location mismatch, use the one from image file. */
+		acev_frag->location = img->image_loc[0];
+	}
+
+	dev_dbg(dev->dev,
+		"ACE config signed magic number 0x%08x, image size 0x%08x\n",
+		ace_conf->magic, ace_conf->image_size);
+	if (ace_conf->magic != VSC_FW_MAGIC) {
+		dev_err(dev->dev,
+			"ACE config signed magic error! magic number 0x%08x, image size 0x%08x\n",
+			ace_conf->magic, ace_conf->image_size);
+		return -EINVAL;
+	}
+
+	acec_frag->data = ace_conf->image;
+	acec_frag->size = ace_conf->image_size;
+	/* Align to 4K boundary */
+	acec_frag->location =
+		((acev_frag->location + acev_frag->size + 0xFFF) & ~(0xFFF));
+	if (img->image_loc[1] && acec_frag->location != img->image_loc[1]) {
+		dev_err(dev->dev,
+			"ACE vision image location error. img->image_loc[1] = 0x%x, calculated is 0x%x\n",
+			img->image_loc[1], acec_frag->location);
+		/* when location mismatch, use the one from image file. */
+		acec_frag->location = img->image_loc[1];
+	}
+
+	return 0;
+}
+
+static int parse_sku_cnf_fw(struct mei_device *dev, const struct firmware *fw)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct fragment *skucnf_frag = &hw->fw.frags[SKU_CONF_TYPE];
+
+	if (fw->size <= sizeof(u32))
+		return -EINVAL;
+
+	skucnf_frag->data = fw->data;
+	skucnf_frag->size = *((u32 *)fw->data) + sizeof(u32);
+	/* SKU config use fixed location */
+	skucnf_frag->location = SKU_CONFIG_LOC;
+	if (fw->size != skucnf_frag->size || fw->size > SKU_MAX_SIZE) {
+		dev_err(dev->dev,
+			"sku config file size is not config size + 4, config size = 0x%x, file size=0x%zx\n",
+			skucnf_frag->size, fw->size);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static u32 sum_CRC(void *data, int size)
+{
+	int i;
+	u32 crc = 0;
+
+	for (i = 0; i < size; i++)
+		crc += *((u8 *)data + i);
+
+	return crc;
+}
+
+static int load_boot(struct mei_device *dev, const void *data, int size)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct vsc_rom_master_frame *frame =
+		(struct vsc_rom_master_frame *)hw->fw.tx_buf;
+	struct vsc_rom_slave_token *token =
+		(struct vsc_rom_slave_token *)hw->fw.rx_buf;
+	const u8 *ptr = data;
+	u32 remain;
+	int ret;
+
+	if (!data || !size)
+		return -EINVAL;
+
+	dev_dbg(dev->dev, "==== %s: image payload size : %d\n", __func__, size);
+	remain = size;
+	while (remain > 0) {
+		u32 max_len = sizeof(frame->data.dl_cont.payload);
+		u32 len = remain > max_len ? max_len : remain;
+
+		memset(frame, 0, sizeof(*frame));
+		memset(token, 0, sizeof(*token));
+		frame->magic = VSC_MAGIC_NUM;
+		frame->cmd = VSC_CMD_DL_CONT;
+
+		frame->data.dl_cont.len = (u16)len;
+		frame->data.dl_cont.end_flag = (remain == len ? 1 : 0);
+		memcpy(frame->data.dl_cont.payload, ptr, len);
+
+		ret = spi_rom_dev_xfer(hw, frame, NULL, VSC_ROM_SPI_PKG_SIZE);
+		if (ret) {
+			dev_err(dev->dev, "%s: transfer failed\n", __func__);
+			break;
+		}
+
+		ptr += len;
+		remain -= len;
+	}
+
+	return ret;
+}
+
+static int load_bootloader(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct vsc_rom_master_frame *frame =
+		(struct vsc_rom_master_frame *)hw->fw.tx_buf;
+	struct vsc_rom_slave_token *token =
+		(struct vsc_rom_slave_token *)hw->fw.rx_buf;
+	struct fragment *fragment = &hw->fw.frags[BOOT_IMAGE_TYPE];
+	int ret;
+
+	if (!fragment->size)
+		return -EINVAL;
+
+	dev_dbg(dev->dev, "verify bootloader token ...\n");
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_QUERY;
+	ret = spi_rom_dev_xfer(hw, frame, token, VSC_ROM_SPI_PKG_SIZE);
+	if (ret)
+		return ret;
+
+	if (token->token != VSC_TOKEN_BOOTLOADER_REQ &&
+	    token->token != VSC_TOKEN_DUMP_RESP) {
+		dev_err(dev->dev,
+			"failed to load bootloader, invalid token 0x%x\n",
+			token->token);
+		return -EINVAL;
+	}
+	dev_dbg(dev->dev, "bootloader token has been verified\n");
+
+	dev_dbg(dev->dev, "start download, image len: %u ...\n", fragment->size);
+	memset(frame, 0, sizeof(*frame));
+	memset(token, 0, sizeof(*token));
+
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_DL_START;
+	frame->data.dl_start.img_type = IMG_BOOTLOADER;
+	frame->data.dl_start.img_len = fragment->size;
+	frame->data.dl_start.img_loc = fragment->location;
+	frame->data.dl_start.option = (u16)hw->fw.fw_option;
+	frame->data.dl_start.crc =
+		sum_CRC(frame, (int)offsetof(struct vsc_rom_master_frame,
+					     data.dl_start.crc));
+	ret = spi_rom_dev_xfer(hw, frame, NULL, VSC_ROM_SPI_PKG_SIZE);
+	if (ret)
+		return ret;
+
+	dev_dbg(dev->dev, "load bootloader payload ...\n");
+	ret = load_boot(dev, fragment->data, fragment->size);
+	if (ret)
+		dev_err(dev->dev, "failed to load bootloader, err : 0x%0x\n",
+			ret);
+
+	return ret;
+}
+
+static int load_fw_bin(struct mei_device *dev, const void *data, int size)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct vsc_master_frame_fw_cont *frame =
+		(struct vsc_master_frame_fw_cont *)hw->fw.tx_buf;
+	struct vsc_bol_slave_token *token =
+		(struct vsc_bol_slave_token *)hw->fw.rx_buf;
+	const u8 *ptr = data;
+	int ret;
+	u32 remain;
+
+	if (!data || !size)
+		return -EINVAL;
+
+	dev_dbg(dev->dev, "==== %s: image payload size : %d\n", __func__, size);
+	remain = size;
+	while (remain > 0) {
+		u32 len = remain > FW_SPI_PKG_SIZE ? FW_SPI_PKG_SIZE : remain;
+
+		memset(frame, 0, sizeof(*frame));
+		memset(token, 0, sizeof(*token));
+		memcpy(frame->payload, ptr, len);
+
+		ret = spi_rom_dev_xfer(hw, frame, NULL, FW_SPI_PKG_SIZE);
+		if (ret) {
+			dev_err(dev->dev, "transfer failed\n");
+			break;
+		}
+
+		ptr += len;
+		remain -= len;
+	}
+
+	return ret;
+}
+
+static int load_fw_frag(struct mei_device *dev, struct fragment *frag, int type)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct vsc_fw_master_frame *frame =
+		(struct vsc_fw_master_frame *)hw->fw.tx_buf;
+	struct vsc_bol_slave_token *token =
+		(struct vsc_bol_slave_token *)hw->rx_buf;
+	int ret;
+
+	dev_dbg(dev->dev,
+		"start download firmware type %d ... loc:0x%08x, size:0x%08x\n",
+		type, frag->location, frag->size);
+	memset(frame, 0, sizeof(*frame));
+	memset(token, 0, sizeof(*token));
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_DL_START;
+	frame->data.dl_start.img_type = type;
+	frame->data.dl_start.img_len = frag->size;
+	frame->data.dl_start.img_loc = frag->location;
+	frame->data.dl_start.option = (u16)hw->fw.fw_option;
+	frame->data.dl_start.crc = sum_CRC(
+		frame, offsetof(struct vsc_fw_master_frame, data.dl_start.crc));
+	ret = spi_rom_dev_xfer(hw, frame, NULL, FW_SPI_PKG_SIZE);
+	if (ret)
+		return ret;
+
+	return load_fw_bin(dev, frag->data, frag->size);
+}
+
+static int load_fw(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct vsc_fw_master_frame *frame =
+		(struct vsc_fw_master_frame *)hw->fw.tx_buf;
+	struct vsc_bol_slave_token *token =
+		(struct vsc_bol_slave_token *)hw->rx_buf;
+	struct fragment *arcsem_frag = NULL;
+	struct fragment *em7d_frag = NULL;
+	struct fragment *acer_frag = NULL;
+	struct fragment *acev_frag = NULL;
+	struct fragment *acec_frag = NULL;
+	struct fragment *skucnf_frag = NULL;
+	int index = 0;
+	int ret;
+
+	if (hw->fw.frags[ARC_SEM_IMG_TYPE].size > 0)
+		arcsem_frag = &hw->fw.frags[ARC_SEM_IMG_TYPE];
+
+	if (hw->fw.frags[EM7D_IMG_TYPE].size > 0)
+		em7d_frag = &hw->fw.frags[EM7D_IMG_TYPE];
+
+	if (hw->fw.frags[ACER_IMG_TYPE].size > 0)
+		acer_frag = &hw->fw.frags[ACER_IMG_TYPE];
+
+	if (hw->fw.frags[ACEV_IMG_TYPE].size > 0)
+		acev_frag = &hw->fw.frags[ACEV_IMG_TYPE];
+
+	if (hw->fw.frags[ACEC_IMG_TYPE].size > 0)
+		acec_frag = &hw->fw.frags[ACEC_IMG_TYPE];
+
+	if (hw->fw.frags[SKU_CONF_TYPE].size > 0)
+		skucnf_frag = &hw->fw.frags[SKU_CONF_TYPE];
+
+	if (!arcsem_frag || !em7d_frag) {
+		dev_err(dev->dev, "invalid image or signature data\n");
+		return -EINVAL;
+	}
+
+	/* send dl_set frame */
+	dev_dbg(dev->dev, "send dl_set frame ...\n");
+	memset(frame, 0, sizeof(*frame));
+	memset(token, 0, sizeof(*token));
+
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_CMD_DL_SET;
+	frame->data.dl_set.option = (u16)hw->fw.fw_option;
+	frame->data.dl_set.img_cnt = (u8)hw->fw.fw_cnt;
+	dev_dbg(dev->dev, "%s: img_cnt = %d ...\n", __func__,
+		frame->data.dl_set.img_cnt);
+
+	frame->data.dl_set.payload[index++] = arcsem_frag->location;
+	frame->data.dl_set.payload[index++] = arcsem_frag->size;
+	if (acer_frag) {
+		frame->data.dl_set.payload[index++] = acer_frag->location;
+		frame->data.dl_set.payload[index++] = acer_frag->size;
+		if (acev_frag) {
+			frame->data.dl_set.payload[index++] =
+				acev_frag->location;
+			frame->data.dl_set.payload[index++] = acev_frag->size;
+		}
+		if (acec_frag) {
+			frame->data.dl_set.payload[index++] =
+				acec_frag->location;
+			frame->data.dl_set.payload[index++] = acec_frag->size;
+		}
+	}
+	frame->data.dl_set.payload[index++] = em7d_frag->location;
+	frame->data.dl_set.payload[index++] = em7d_frag->size;
+	frame->data.dl_set.payload[hw->fw.fw_cnt * 2] = sum_CRC(
+		frame, (int)offsetof(struct vsc_fw_master_frame,
+				     data.dl_set.payload[hw->fw.fw_cnt * 2]));
+
+	ret = spi_rom_dev_xfer(hw, frame, NULL, FW_SPI_PKG_SIZE);
+	if (ret)
+		return ret;
+
+	/* load ARC-SEM FW image */
+	if (arcsem_frag) {
+		ret = load_fw_frag(dev, arcsem_frag, IMG_ARCSEM);
+		if (ret)
+			return ret;
+	}
+
+	/* load ACE FW image */
+	if (acer_frag) {
+		ret = load_fw_frag(dev, acer_frag, IMG_ACE_RUNTIME);
+		if (ret)
+			return ret;
+	}
+
+	if (acev_frag) {
+		ret = load_fw_frag(dev, acev_frag, IMG_ACE_VISION);
+		if (ret)
+			return ret;
+	}
+
+	if (acec_frag) {
+		ret = load_fw_frag(dev, acec_frag, IMG_ACE_CONFIG);
+		if (ret)
+			return ret;
+	}
+
+	/* load EM7D FW image */
+	if (em7d_frag) {
+		ret = load_fw_frag(dev, em7d_frag, IMG_EM7D);
+		if (ret)
+			return ret;
+	}
+
+	/* load SKU Config */
+	if (skucnf_frag) {
+		ret = load_fw_frag(dev, skucnf_frag, IMG_SKU_CONFIG);
+		if (ret)
+			return ret;
+	}
+
+	memset(frame, 0, sizeof(*frame));
+	frame->magic = VSC_MAGIC_NUM;
+	frame->cmd = VSC_TOKEN_CAM_BOOT;
+	frame->data.boot.check_sum = sum_CRC(
+		frame, offsetof(struct vsc_fw_master_frame, data.dl_start.crc));
+	ret = spi_rom_dev_xfer(hw, frame, NULL, FW_SPI_PKG_SIZE);
+	if (ret)
+		dev_err(dev->dev, "failed to boot fw, err : 0x%x\n", ret);
+
+	return ret;
+}
+
+static int init_hw(struct mei_device *dev)
+{
+	int ret;
+	const struct firmware *fw = NULL;
+	const struct firmware *sensor_fw = NULL;
+	const struct firmware *sku_cnf_fw = NULL;
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	ret = check_silicon(dev);
+	if (ret)
+		return ret;
+
+	dev_dbg(dev->dev,
+		"%s: FW files. Firmware Boot File: %s, Sensor FW File: %s, Sku Config File: %s\n",
+		__func__, hw->fw.fw_file_name, hw->fw.sensor_file_name,
+		hw->fw.sku_cnf_file_name);
+	ret = request_firmware(&fw, hw->fw.fw_file_name, dev->dev);
+	if (ret < 0 || !fw) {
+		dev_err(&hw->spi->dev, "file not found %s\n",
+			hw->fw.fw_file_name);
+		return ret;
+	}
+
+	ret = parse_main_fw(dev, fw);
+	if (ret || !fw) {
+		dev_err(&hw->spi->dev, "parse fw %s failed\n",
+			hw->fw.fw_file_name);
+		goto release;
+	}
+
+	if (hw->fw.fw_cnt < IMG_ARC_ACER_ACEV_ACECNF_EM7D) {
+		ret = request_firmware(&sensor_fw, hw->fw.sensor_file_name,
+				       dev->dev);
+		if (ret < 0 || !sensor_fw) {
+			dev_err(&hw->spi->dev, "file not found %s\n",
+				hw->fw.sensor_file_name);
+			goto release;
+		}
+		ret = parse_sensor_fw(dev, sensor_fw);
+		if (ret) {
+			dev_err(&hw->spi->dev, "parse fw %s failed\n",
+				hw->fw.sensor_file_name);
+			goto release_sensor;
+		}
+	}
+
+	ret = request_firmware(&sku_cnf_fw, hw->fw.sku_cnf_file_name, dev->dev);
+	if (ret < 0 || !sku_cnf_fw) {
+		dev_err(&hw->spi->dev, "file not found %s\n",
+			hw->fw.sku_cnf_file_name);
+		goto release_sensor;
+	}
+
+	ret = parse_sku_cnf_fw(dev, sku_cnf_fw);
+	if (ret) {
+		dev_err(&hw->spi->dev, "parse fw %s failed\n",
+			hw->fw.sensor_file_name);
+		goto release_cnf;
+	}
+
+	ret = load_bootloader(dev);
+	if (ret)
+		goto release_cnf;
+
+	ret = load_fw(dev);
+	if (ret)
+		goto release_cnf;
+
+	return 0;
+
+release_cnf:
+	release_firmware(sku_cnf_fw);
+release_sensor:
+	release_firmware(sensor_fw);
+release:
+	release_firmware(fw);
+	return ret;
+}
+
+/**
+ * mei_vsc_fw_status - read fw status register from pci config space
+ *
+ * @dev: mei device
+ * @fw_status: fw status
+ *
+ * Return: 0 on success, error otherwise
+ */
+static int mei_vsc_fw_status(struct mei_device *dev,
+			     struct mei_fw_status *fw_status)
+{
+	if (!fw_status)
+		return -EINVAL;
+
+	fw_status->count = 0;
+	return 0;
+}
+
+/**
+ * mei_vsc_pg_state  - translate internal pg state
+ *   to the mei power gating state
+ *
+ * @dev:  mei device
+ *
+ * Return: MEI_PG_OFF if aliveness is on and MEI_PG_ON otherwise
+ */
+static inline enum mei_pg_state mei_vsc_pg_state(struct mei_device *dev)
+{
+	return MEI_PG_OFF;
+}
+
+/**
+ * mei_vsc_intr_enable - enables mei device interrupts
+ *
+ * @dev: the device structure
+ */
+static void mei_vsc_intr_enable(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	enable_irq(hw->wakeuphostint);
+}
+
+/**
+ * mei_vsc_intr_disable - disables mei device interrupts
+ *
+ * @dev: the device structure
+ */
+static void mei_vsc_intr_disable(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	disable_irq(hw->wakeuphostint);
+}
+
+/**
+ * mei_vsc_intr_clear - clear and stop interrupts
+ *
+ * @dev: the device structure
+ */
+static void mei_vsc_intr_clear(struct mei_device *dev)
+{
+	;
+}
+
+/**
+ * mei_vsc_synchronize_irq - wait for pending IRQ handlers
+ *
+ * @dev: the device structure
+ */
+static void mei_vsc_synchronize_irq(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	synchronize_irq(hw->wakeuphostint);
+}
+
+/**
+ * mei_vsc_hw_config - configure hw dependent settings
+ *
+ * @dev: mei device
+ *
+ * Return:
+ *  * -EINVAL when read_fws is not set
+ *  * 0 on success
+ *
+ */
+static int mei_vsc_hw_config(struct mei_device *dev)
+{
+	return 0;
+}
+
+/**
+ * mei_vsc_host_set_ready - enable device
+ *
+ * @dev: mei device
+ */
+static void mei_vsc_host_set_ready(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	hw->host_ready = true;
+}
+
+/**
+ * mei_vsc_host_is_ready - check whether the host has turned ready
+ *
+ * @dev: mei device
+ * Return: bool
+ */
+static bool mei_vsc_host_is_ready(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	return hw->host_ready;
+}
+
+/**
+ * mei_vsc_hw_is_ready - check whether the me(hw) has turned ready
+ *
+ * @dev: mei device
+ * Return: bool
+ */
+static bool mei_vsc_hw_is_ready(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	return hw->fw_ready;
+}
+
+/**
+ * mei_vsc_hw_start - hw start routine
+ *
+ * @dev: mei device
+ * Return: 0 on success, error otherwise
+ */
+#define MEI_SPI_START_TIMEOUT 200
+static int mei_vsc_hw_start(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	u8 buf;
+	int len;
+	int ret;
+	int timeout = MEI_SPI_START_TIMEOUT;
+
+	mei_vsc_host_set_ready(dev);
+	atomic_set(&hw->lock_cnt, 0);
+	mei_vsc_intr_enable(dev);
+
+	/* wait for FW ready */
+	while (timeout > 0) {
+		msleep(50);
+		timeout -= 50;
+		ret = mei_vsc_read_raw(hw, &buf, sizeof(buf), &len);
+		if (!ret && ret != -EAGAIN)
+			break;
+	}
+
+	if (timeout <= 0)
+		return -ENODEV;
+
+	dev_dbg(dev->dev, "hw is ready\n");
+	hw->fw_ready = true;
+	return 0;
+}
+
+/**
+ * mei_vsc_hbuf_is_ready - checks if host buf is empty.
+ *
+ * @dev: the device structure
+ *
+ * Return: true if empty, false - otherwise.
+ */
+static bool mei_vsc_hbuf_is_ready(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	return hw->write_lock_cnt == 0;
+}
+
+/**
+ * mei_vsc_hbuf_empty_slots - counts write empty slots.
+ *
+ * @dev: the device structure
+ *
+ * Return:  empty slots count
+ */
+static int mei_vsc_hbuf_empty_slots(struct mei_device *dev)
+{
+	return MAX_MEI_MSG_SIZE / MEI_SLOT_SIZE;
+}
+
+/**
+ * mei_vsc_hbuf_depth - returns depth of the hw buf.
+ *
+ * @dev: the device structure
+ *
+ * Return: size of hw buf in slots
+ */
+static u32 mei_vsc_hbuf_depth(const struct mei_device *dev)
+{
+	return MAX_MEI_MSG_SIZE / MEI_SLOT_SIZE;
+}
+
+/**
+ * mei_vsc_write - writes a message to FW.
+ *
+ * @dev: the device structure
+ * @hdr: header of message
+ * @hdr_len: header length in bytes: must be multiplication of a slot (4bytes)
+ * @data: payload
+ * @data_len: payload length in bytes
+ *
+ * Return: 0 if success, < 0 - otherwise.
+ */
+static int mei_vsc_write(struct mei_device *dev, const void *hdr,
+			 size_t hdr_len, const void *data, size_t data_len)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	int ret;
+	char *buf = hw->tx_buf;
+
+	if (WARN_ON(!hdr || !data || hdr_len & 0x3 ||
+		    data_len > MAX_SPI_MSG_SIZE)) {
+		dev_err(dev->dev,
+			"%s error write msg hdr_len %zu data_len %zu\n",
+			__func__, hdr_len, data_len);
+		return -EINVAL;
+	}
+
+	hw->write_lock_cnt++;
+	memcpy(buf, hdr, hdr_len);
+	memcpy(buf + hdr_len, data, data_len);
+	dev_dbg(dev->dev, "%s %d" MEI_HDR_FMT, __func__, hw->write_lock_cnt,
+		MEI_HDR_PRM((struct mei_msg_hdr *)hdr));
+
+	ret = mei_vsc_write_raw(hw, buf, hdr_len + data_len);
+	if (ret)
+		dev_err(dev->dev, MEI_HDR_FMT "hdr_len %zu data len %zu\n",
+			MEI_HDR_PRM((struct mei_msg_hdr *)hdr), hdr_len,
+			data_len);
+
+	hw->write_lock_cnt--;
+	return ret;
+}
+
+/**
+ * mei_vsc_read
+ *  read spi message
+ *
+ * @dev: the device structure
+ *
+ * Return: mei hdr value (u32)
+ */
+static inline u32 mei_vsc_read(const struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	int ret;
+
+	ret = mei_vsc_read_raw(hw, hw->rx_buf, sizeof(hw->rx_buf), &hw->rx_len);
+	if (ret || hw->rx_len < sizeof(u32))
+		return 0;
+
+	return *(u32 *)hw->rx_buf;
+}
+
+/**
+ * mei_vsc_count_full_read_slots - counts read full slots.
+ *
+ * @dev: the device structure
+ *
+ * Return: -EOVERFLOW if overflow, otherwise filled slots count
+ */
+static int mei_vsc_count_full_read_slots(struct mei_device *dev)
+{
+	return MAX_MEI_MSG_SIZE / MEI_SLOT_SIZE;
+}
+
+/**
+ * mei_vsc_read_slots - reads a message from mei device.
+ *
+ * @dev: the device structure
+ * @buf: message buf will be written
+ * @len: message size will be read
+ *
+ * Return: always 0
+ */
+static int mei_vsc_read_slots(struct mei_device *dev, unsigned char *buf,
+			      unsigned long len)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct mei_msg_hdr *hdr;
+
+	hdr = (struct mei_msg_hdr *)hw->rx_buf;
+	WARN_ON(len != hdr->length || hdr->length + sizeof(*hdr) != hw->rx_len);
+	memcpy(buf, hw->rx_buf + sizeof(*hdr), len);
+	return 0;
+}
+
+/**
+ * mei_vsc_pg_in_transition - is device now in pg transition
+ *
+ * @dev: the device structure
+ *
+ * Return: true if in pg transition, false otherwise
+ */
+static bool mei_vsc_pg_in_transition(struct mei_device *dev)
+{
+	return dev->pg_event >= MEI_PG_EVENT_WAIT &&
+	       dev->pg_event <= MEI_PG_EVENT_INTR_WAIT;
+}
+
+/**
+ * mei_vsc_pg_is_enabled - detect if PG is supported by HW
+ *
+ * @dev: the device structure
+ *
+ * Return: true is pg supported, false otherwise
+ */
+static bool mei_vsc_pg_is_enabled(struct mei_device *dev)
+{
+	return false;
+}
+
+/**
+ * mei_vsc_hw_reset - resets fw.
+ *
+ * @dev: the device structure
+ * @intr_enable: if interrupt should be enabled after reset.
+ *
+ * Return: 0 on success an error code otherwise
+ */
+static int mei_vsc_hw_reset(struct mei_device *dev, bool intr_enable)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	int ret;
+
+	mei_vsc_intr_disable(dev);
+	ret = vsc_reset(dev);
+	if (ret)
+		return ret;
+
+	if (hw->disconnect)
+		return 0;
+
+	ret = init_hw(dev);
+	if (ret)
+		return -ENODEV;
+
+	hw->seq = 0;
+	return 0;
+}
+
+/**
+ * mei_vsc_irq_quick_handler - The ISR of the MEI device
+ *
+ * @irq: The irq number
+ * @dev_id: pointer to the device structure
+ *
+ * Return: irqreturn_t
+ */
+irqreturn_t mei_vsc_irq_quick_handler(int irq, void *dev_id)
+{
+	struct mei_device *dev = (struct mei_device *)dev_id;
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	dev_dbg(dev->dev, "interrupt top half lock_cnt %d state %d\n",
+		atomic_read(&hw->lock_cnt), dev->dev_state);
+
+	atomic_inc(&hw->lock_cnt);
+	wake_up(&hw->xfer_wait);
+	if (dev->dev_state == MEI_DEV_INITIALIZING ||
+	    dev->dev_state == MEI_DEV_RESETTING)
+		return IRQ_HANDLED;
+
+	return IRQ_WAKE_THREAD;
+}
+
+/**
+ * mei_vsc_irq_thread_handler - function called after ISR to handle the interrupt
+ * processing.
+ *
+ * @irq: The irq number
+ * @dev_id: pointer to the device structure
+ *
+ * Return: irqreturn_t
+ *
+ */
+irqreturn_t mei_vsc_irq_thread_handler(int irq, void *dev_id)
+{
+	struct mei_device *dev = (struct mei_device *)dev_id;
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct list_head cmpl_list;
+	s32 slots;
+	int rets = 0;
+
+	dev_dbg(dev->dev,
+		"function called after ISR to handle the interrupt processing dev->dev_state=%d.\n",
+		dev->dev_state);
+
+	/* initialize our complete list */
+	mutex_lock(&dev->device_lock);
+	INIT_LIST_HEAD(&cmpl_list);
+
+	/* check slots available for reading */
+	slots = mei_count_full_read_slots(dev);
+	dev_dbg(dev->dev, "slots to read = %08x\n", slots);
+
+reread:
+	while (spi_need_read(hw)) {
+		dev_dbg(dev->dev, "slots to read in = %08x\n", slots);
+		rets = mei_irq_read_handler(dev, &cmpl_list, &slots);
+		/* There is a race between ME write and interrupt delivery:
+		 * Not all data is always available immediately after the
+		 * interrupt, so try to read again on the next interrupt.
+		 */
+		if (rets == -ENODATA)
+			break;
+
+		if (rets && (dev->dev_state != MEI_DEV_RESETTING &&
+			     dev->dev_state != MEI_DEV_POWER_DOWN)) {
+			dev_err(dev->dev, "mei_irq_read_handler ret = %d.\n",
+				rets);
+			schedule_work(&dev->reset_work);
+			goto end;
+		}
+	}
+	dev_dbg(dev->dev, "slots to read out = %08x\n", slots);
+
+	dev->hbuf_is_ready = mei_hbuf_is_ready(dev);
+	rets = mei_irq_write_handler(dev, &cmpl_list);
+
+	dev->hbuf_is_ready = mei_hbuf_is_ready(dev);
+	mei_irq_compl_handler(dev, &cmpl_list);
+
+	if (spi_need_read(hw))
+		goto reread;
+
+end:
+	dev_dbg(dev->dev, "interrupt thread end ret = %d\n", rets);
+	mutex_unlock(&dev->device_lock);
+	return IRQ_HANDLED;
+}
+
+static const struct mei_hw_ops mei_vsc_hw_ops = {
+
+	.fw_status = mei_vsc_fw_status,
+	.pg_state = mei_vsc_pg_state,
+
+	.host_is_ready = mei_vsc_host_is_ready,
+
+	.hw_is_ready = mei_vsc_hw_is_ready,
+	.hw_reset = mei_vsc_hw_reset,
+	.hw_config = mei_vsc_hw_config,
+	.hw_start = mei_vsc_hw_start,
+
+	.pg_in_transition = mei_vsc_pg_in_transition,
+	.pg_is_enabled = mei_vsc_pg_is_enabled,
+
+	.intr_clear = mei_vsc_intr_clear,
+	.intr_enable = mei_vsc_intr_enable,
+	.intr_disable = mei_vsc_intr_disable,
+	.synchronize_irq = mei_vsc_synchronize_irq,
+
+	.hbuf_free_slots = mei_vsc_hbuf_empty_slots,
+	.hbuf_is_ready = mei_vsc_hbuf_is_ready,
+	.hbuf_depth = mei_vsc_hbuf_depth,
+	.write = mei_vsc_write,
+
+	.rdbuf_full_slots = mei_vsc_count_full_read_slots,
+	.read_hdr = mei_vsc_read,
+	.read = mei_vsc_read_slots
+};
+
+/**
+ * mei_vsc_dev_init - allocates and initializes the mei device structure
+ *
+ * @parent: device associated with physical device (spi/platform)
+ *
+ * Return: The mei_device pointer on success, NULL on failure.
+ */
+struct mei_device *mei_vsc_dev_init(struct device *parent)
+{
+	struct mei_device *dev;
+	struct mei_vsc_hw *hw;
+
+	dev = devm_kzalloc(parent, sizeof(*dev) + sizeof(*hw), GFP_KERNEL);
+	if (!dev)
+		return NULL;
+
+	mei_device_init(dev, parent, &mei_vsc_hw_ops);
+	dev->fw_f_fw_ver_supported = 0;
+	dev->kind = 0;
+	return dev;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/hw-vsc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/hw-vsc.h
@@ -0,0 +1,377 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021, Intel Corporation. All rights reserved.
+ * Intel Management Engine Interface (Intel MEI) Linux driver
+ */
+
+#ifndef _MEI_HW_SPI_H_
+#define _MEI_HW_SPI_H_
+
+#include <linux/irqreturn.h>
+#include <linux/spi/spi.h>
+#include <linux/mei.h>
+#include <linux/types.h>
+
+#include "mei_dev.h"
+
+struct mei_cfg {
+	const struct mei_fw_status fw_status;
+	const char *kind;
+	u32 fw_ver_supported : 1;
+	u32 hw_trc_supported : 1;
+};
+
+enum FRAG_TYPE {
+	BOOT_IMAGE_TYPE,
+	ARC_SEM_IMG_TYPE,
+	EM7D_IMG_TYPE,
+	ACER_IMG_TYPE,
+	ACEV_IMG_TYPE,
+	ACEC_IMG_TYPE,
+	SKU_CONF_TYPE,
+	FRAGMENT_TYPE_MAX,
+};
+
+struct fragment {
+	enum FRAG_TYPE type;
+	u32 location;
+	const u8 *data;
+	u32 size;
+};
+
+irqreturn_t mei_vsc_irq_quick_handler(int irq, void *dev_id);
+irqreturn_t mei_vsc_irq_thread_handler(int irq, void *dev_id);
+struct mei_device *mei_vsc_dev_init(struct device *parent);
+
+#define VSC_MAGIC_NUM 0x49505343
+#define VSC_FILE_MAGIC 0x46564353
+#define VSC_FW_MAGIC 0x49574653
+#define VSC_ROM_SPI_PKG_SIZE 256
+#define FW_SPI_PKG_SIZE 512
+
+#define IMG_MAX_LOC (0x50FFFFFF)
+#define FW_MAX_SIZE (0x200000)
+#define SKU_CONFIG_LOC (0x5001A000)
+#define SKU_MAX_SIZE (4100)
+
+#define IMG_DMA_ENABLE_OPTION (1 << 0)
+
+#define SIG_SIZE 384
+#define PUBKEY_SIZE 384
+#define CSSHEADER_SIZE 128
+
+#define VSC_CMD_QUERY 0
+#define VSC_CMD_DL_SET 1
+#define VSC_CMD_DL_START 2
+#define VSC_CMD_DL_CONT 3
+#define VSC_CMD_DUMP_MEM 4
+#define VSC_CMD_SET_REG 5
+#define VSC_CMD_PRINT_ROM_VERSION 6
+#define VSC_CMD_WRITE_FLASH 7
+#define VSC_CMD_RESERVED 8
+
+enum IMAGE_TYPE {
+	IMG_DEBUG,
+	IMG_BOOTLOADER,
+	IMG_EM7D,
+	IMG_ARCSEM,
+	IMG_ACE_RUNTIME,
+	IMG_ACE_VISION,
+	IMG_ACE_CONFIG,
+	IMG_SKU_CONFIG
+};
+
+/*image count define, refer to Clover Fall Boot ROM HLD 1.0*/
+#define IMG_ACEV_ACECNF 2
+#define IMG_BOOT_ARC_EM7D 3
+#define IMG_BOOT_ARC_ACER_EM7D 4
+#define IMG_BOOT_ARC_ACER_ACEV_EM7D 5
+#define IMG_BOOT_ARC_ACER_ACEV_ACECNF_EM7D 6
+#define IMG_ARC_ACER_ACEV_ACECNF_EM7D (IMG_BOOT_ARC_ACER_ACEV_ACECNF_EM7D - 1)
+#define IMG_CNT_MAX IMG_BOOT_ARC_ACER_ACEV_ACECNF_EM7D
+
+#define VSC_TOKEN_BOOTLOADER_REQ 1
+#define VSC_TOKEN_FIRMWARE_REQ 2
+#define VSC_TOKEN_DOWNLOAD_CONT 3
+#define VSC_TOKEN_DUMP_RESP 4
+#define VSC_TOKEN_DUMP_CONT 5
+#define VSC_TOKEN_SKU_CONFIG_REQ 6
+#define VSC_TOKEN_ERROR 7
+#define VSC_TOKEN_DUMMY 8
+#define VSC_TOKEN_CAM_STATUS_RESP 9
+#define VSC_TOKEN_CAM_BOOT 10
+
+#define MAX_SVN_VALUE (0xFFFFFFFE)
+
+#define EFUSE1_ADDR (0xE0030000 + 0x38)
+#define STRAP_ADDR (0xE0030000 + 0x100)
+
+#define SI_MAINSTEPPING_VERSION_OFFSET (4)
+#define SI_MAINSTEPPING_VERSION_MASK (0xF)
+#define SI_MAINSTEPPING_VERSION_A (0x0)
+#define SI_MAINSTEPPING_VERSION_B (0x1)
+#define SI_MAINSTEPPING_VERSION_C (0x2)
+
+#define SI_SUBSTEPPING_VERSION_OFFSET (0x0)
+#define SI_SUBSTEPPING_VERSION_MASK (0xF)
+#define SI_SUBSTEPPING_VERSION_0 (0x0)
+#define SI_SUBSTEPPING_VERSION_0_PRIME (0x1)
+#define SI_SUBSTEPPING_VERSION_1 (0x2)
+#define SI_SUBSTEPPING_VERSION_1_PRIME (0x3)
+
+#define SI_STRAP_KEY_SRC_OFFSET (16)
+#define SI_STRAP_KEY_SRC_MASK (0x1)
+
+#define SI_STRAP_KEY_SRC_DEBUG (0x0)
+#define SI_STRAP_KEY_SRC_PRODUCT (0x1)
+
+struct vsc_rom_master_frame {
+	u32 magic;
+	u8 cmd;
+	union {
+		struct {
+			u8 img_type;
+			u16 option;
+			u32 img_len;
+			u32 img_loc;
+			u32 crc;
+			u8 res[0];
+		} __packed dl_start;
+		struct {
+			u8 option;
+			u16 img_cnt;
+			u32 payload[(VSC_ROM_SPI_PKG_SIZE - 8) / 4];
+		} __packed dl_set;
+		struct {
+			u8 end_flag;
+			u16 len;
+			u8 payload[VSC_ROM_SPI_PKG_SIZE - 8];
+		} __packed dl_cont;
+		struct {
+			u8 res;
+			u16 len;
+			u32 addr;
+#define ROM_DUMP_MEM_RESERVE_SIZE 12
+			u8 payload[VSC_ROM_SPI_PKG_SIZE -
+				   ROM_DUMP_MEM_RESERVE_SIZE];
+		} __packed dump_mem;
+		struct {
+			u8 res[3];
+			u32 addr;
+			u32 val;
+#define ROM_SET_REG_RESERVE_SIZE 16
+			u8 payload[VSC_ROM_SPI_PKG_SIZE -
+				   ROM_SET_REG_RESERVE_SIZE];
+		} __packed set_reg;
+		struct {
+			u8 ins[0];
+		} __packed undoc_f1;
+		struct {
+			u32 addr;
+			u32 len;
+			u8 payload[0];
+		} __packed os_dump_mem;
+		u8 reserve[VSC_ROM_SPI_PKG_SIZE - 5];
+	} data;
+} __packed;
+
+struct vsc_fw_master_frame {
+	u32 magic;
+	u8 cmd;
+	union {
+		struct {
+			u16 option;
+			u8 img_type;
+			u32 img_len;
+			u32 img_loc;
+			u32 crc;
+			u8 res[0];
+		} __packed dl_start;
+		struct {
+			u16 option;
+			u8 img_cnt;
+			u32 payload[(FW_SPI_PKG_SIZE - 8) / 4];
+		} __packed dl_set;
+		struct {
+			u8 end_flag;
+			u16 len;
+			u8 payload[FW_SPI_PKG_SIZE - 8];
+		} __packed dl_cont;
+		struct {
+			u32 addr;
+			u8 len;
+			u8 payload[0];
+		} __packed dump_mem;
+		struct {
+			u32 addr;
+			u32 val;
+			u8 payload[0];
+		} __packed set_reg;
+		struct {
+			u8 ins[0];
+		} __packed undoc_f1;
+		struct {
+			u32 addr;
+			u32 len;
+			u8 payload[0];
+		} __packed os_dump_mem;
+		struct {
+			u8 resv[3];
+			u32 check_sum;
+#define LOADER_BOOT_RESERVE_SIZE 12
+			u8 payload[FW_SPI_PKG_SIZE - LOADER_BOOT_RESERVE_SIZE];
+		} __packed boot;
+		u8 reserve[FW_SPI_PKG_SIZE - 5];
+	} data;
+} __packed;
+
+struct vsc_master_frame_fw_cont {
+	u8 payload[FW_SPI_PKG_SIZE];
+} __packed;
+
+struct vsc_rom_slave_token {
+	u32 magic;
+	u8 token;
+	u8 type;
+	u8 res[2];
+	u8 payload[VSC_ROM_SPI_PKG_SIZE - 8];
+} __packed;
+
+struct vsc_bol_slave_token {
+	u32 magic;
+	u8 token;
+	u8 type;
+	u8 res[2];
+	u8 payload[FW_SPI_PKG_SIZE - 8];
+} __packed;
+
+struct vsc_boot_img {
+	u32 magic;
+	u32 option;
+	u32 image_count;
+	u32 image_loc[IMG_CNT_MAX];
+} __packed;
+
+struct vsc_sensor_img_t {
+	u32 magic;
+	u32 option;
+	u32 image_count;
+	u32 image_loc[IMG_ACEV_ACECNF];
+} __packed;
+
+struct bootloader_sign {
+	u32 magic;
+	u32 image_size;
+	u8 image[0];
+} __packed;
+
+struct manifest {
+	u32 svn;
+	u32 header_ver;
+	u32 comp_flags;
+	u32 comp_name;
+	u32 comp_vendor_name;
+	u32 module_size;
+	u32 module_addr;
+} __packed;
+
+struct firmware_sign {
+	u32 magic;
+	u32 image_size;
+	u8 image[1];
+} __packed;
+
+/* spi transport layer */
+#define PACKET_SYNC 0x31
+#define MAX_SPI_MSG_SIZE 2048
+#define MAX_MEI_MSG_SIZE 512
+
+#define CRC_SIZE sizeof(u32)
+#define PACKET_SIZE(pkt) (sizeof(pkt->hdr) + (pkt->hdr.len) + (CRC_SIZE))
+#define MAX_PACKET_SIZE                                                        \
+	(sizeof(struct spi_xfer_hdr) + MAX_SPI_MSG_SIZE + (CRC_SIZE))
+
+/* SPI xfer timeout size definition */
+#define XFER_TIMEOUT_BYTES 700
+#define MAX_XFER_BUFFER_SIZE ((MAX_PACKET_SIZE) + (XFER_TIMEOUT_BYTES))
+
+struct spi_xfer_hdr {
+	u8 sync;
+	u8 cmd;
+	u16 len;
+	u32 seq;
+} __packed;
+
+struct spi_xfer_packet {
+	struct spi_xfer_hdr hdr;
+	u8 buf[MAX_XFER_BUFFER_SIZE - sizeof(struct spi_xfer_hdr)];
+} __packed;
+
+#define CMD_SPI_WRITE 0x01
+#define CMD_SPI_READ 0x02
+#define CMD_SPI_RESET_NOTIFY 0x04
+
+#define CMD_SPI_ACK 0x10
+#define CMD_SPI_NACK 0x11
+#define CMD_SPI_BUSY 0x12
+#define CMD_SPI_FATAL_ERR 0x13
+
+struct host_timestamp {
+	u64 realtime;
+	u64 boottime;
+} __packed;
+
+struct vsc_boot_fw {
+	u32 main_ver;
+	u32 sub_ver;
+	u32 key_src;
+	u32 svn;
+
+	u8 tx_buf[FW_SPI_PKG_SIZE];
+	u8 rx_buf[FW_SPI_PKG_SIZE];
+
+	/* FirmwareBootFile */
+	char fw_file_name[256];
+	/* PkgBootFile */
+	char sensor_file_name[256];
+	/* SkuConfigBootFile */
+	char sku_cnf_file_name[256];
+
+	u32 fw_option;
+	u32 fw_cnt;
+	struct fragment frags[FRAGMENT_TYPE_MAX];
+};
+
+struct mei_vsc_hw {
+	struct spi_device *spi;
+	struct spi_transfer xfer;
+	struct spi_message msg;
+	u8 rx_buf[MAX_SPI_MSG_SIZE];
+	u8 tx_buf[MAX_SPI_MSG_SIZE];
+	u32 rx_len;
+
+	int wakeuphostint;
+	struct gpio_desc *wakeuphost;
+	struct gpio_desc *resetfw;
+	struct gpio_desc *wakeupfw;
+
+	struct vsc_boot_fw fw;
+	bool host_ready;
+	bool fw_ready;
+
+	/* mei transport layer */
+	u32 seq;
+	u8 tx_buf1[MAX_XFER_BUFFER_SIZE];
+	u8 rx_buf1[MAX_XFER_BUFFER_SIZE];
+
+	struct mutex mutex;
+	bool disconnect;
+	atomic_t lock_cnt;
+	int write_lock_cnt;
+	wait_queue_head_t xfer_wait;
+	char cam_sensor_name[32];
+};
+
+#define to_vsc_hw(dev) ((struct mei_vsc_hw *)((dev)->hw))
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/interrupt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/interrupt.c
@@ -424,31 +424,26 @@
 	list_for_each_entry(cl, &dev->file_list, link) {
 		if (mei_cl_hbm_equal(cl, mei_hdr)) {
 			cl_dbg(dev, cl, "got a message\n");
-			break;
+			ret = mei_cl_irq_read_msg(cl, mei_hdr, meta_hdr, cmpl_list);
+			goto reset_slots;
 		}
 	}
 
 	/* if no recipient cl was found we assume corrupted header */
-	if (&cl->link == &dev->file_list) {
-		/* A message for not connected fixed address clients
-		 * should be silently discarded
-		 * On power down client may be force cleaned,
-		 * silently discard such messages
-		 */
-		if (hdr_is_fixed(mei_hdr) ||
-		    dev->dev_state == MEI_DEV_POWER_DOWN) {
-			mei_irq_discard_msg(dev, mei_hdr, mei_hdr->length);
-			ret = 0;
-			goto reset_slots;
-		}
-		dev_err(dev->dev, "no destination client found 0x%08X\n",
-				dev->rd_msg_hdr[0]);
-		ret = -EBADMSG;
-		goto end;
+	/* A message for not connected fixed address clients
+	 * should be silently discarded
+	 * On power down client may be force cleaned,
+	 * silently discard such messages
+	 */
+	if (hdr_is_fixed(mei_hdr) ||
+	    dev->dev_state == MEI_DEV_POWER_DOWN) {
+		mei_irq_discard_msg(dev, mei_hdr, mei_hdr->length);
+		ret = 0;
+		goto reset_slots;
 	}
-
-	ret = mei_cl_irq_read_msg(cl, mei_hdr, meta_hdr, cmpl_list);
-
+	dev_err(dev->dev, "no destination client found 0x%08X\n", dev->rd_msg_hdr[0]);
+	ret = -EBADMSG;
+	goto end;
 
 reset_slots:
 	/* reset the number of slots and header */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/main.c
@@ -327,7 +327,7 @@
 	}
 
 	if (!mei_cl_is_connected(cl)) {
-		cl_err(dev, cl, "is not connected");
+		cl_dbg(dev, cl, "is not connected");
 		rets = -ENODEV;
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/pci-me.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/pci-me.c
@@ -23,6 +23,9 @@
 #include "hw-me-regs.h"
 #include "hw-me.h"
 
+static bool disable_msi;
+module_param(disable_msi, bool, 0);
+
 /* mei_pci_tbl - PCI Device ID Table */
 static const struct pci_device_id mei_me_pci_tbl[] = {
 	{MEI_PCI_DEVICE(MEI_DEV_ID_82946GZ, MEI_ME_ICH_CFG)},
@@ -113,6 +116,17 @@
 	{MEI_PCI_DEVICE(MEI_DEV_ID_ADP_S, MEI_ME_PCH15_CFG)},
 	{MEI_PCI_DEVICE(MEI_DEV_ID_ADP_LP, MEI_ME_PCH15_CFG)},
 	{MEI_PCI_DEVICE(MEI_DEV_ID_ADP_P, MEI_ME_PCH15_CFG)},
+	{MEI_PCI_DEVICE(MEI_DEV_ID_ADP_N, MEI_ME_PCH15_CFG)},
+
+	{MEI_PCI_DEVICE(MEI_DEV_ID_RPL_S, MEI_ME_PCH15_SPS_CFG)},
+
+	{MEI_PCI_DEVICE(MEI_DEV_ID_MTL_M, MEI_ME_PCH15_CFG)},
+	{MEI_PCI_DEVICE(MEI_DEV_ID_ARL_S, MEI_ME_PCH15_CFG)},
+	{MEI_PCI_DEVICE(MEI_DEV_ID_ARL_H, MEI_ME_PCH15_CFG)},
+
+	{MEI_PCI_DEVICE(MEI_DEV_ID_LNL_M, MEI_ME_PCH15_CFG)},
+
+	{MEI_PCI_DEVICE(MEI_DEV_ID_PTL_P, MEI_ME_PCH15_CFG)},
 
 	/* required last entry */
 	{0, }
@@ -215,7 +229,8 @@
 	hw->mem_addr = pcim_iomap_table(pdev)[0];
 	hw->read_fws = mei_me_read_fws;
 
-	pci_enable_msi(pdev);
+	if (!disable_msi)
+		pci_enable_msi(pdev);
 
 	hw->irq = pdev->irq;
 
@@ -391,8 +406,10 @@
 	}
 
 	err = mei_restart(dev);
-	if (err)
+	if (err) {
+		free_irq(pdev->irq, dev);
 		return err;
+	}
 
 	/* Start timer if stopped in suspend */
 	schedule_delayed_work(&dev->timer_work, HZ);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/mei/spi-vsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/mei/spi-vsc.c
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021, Intel Corporation. All rights reserved.
+ * Intel Management Engine Interface (Intel MEI) Linux driver
+ */
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/mei.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/spi/spi.h>
+
+#include "hw-vsc.h"
+
+#define CVFD_ACPI_ID_TGL "INTC1059"
+#define CVFD_ACPI_ID_ADL "INTC1095"
+#define LINK_NUMBER (1)
+#define METHOD_NAME_SID "SID"
+
+/* gpio resources */
+static const struct acpi_gpio_params wakeuphost_gpio = { 0, 0, false };
+static const struct acpi_gpio_params wakeuphostint_gpio = { 1, 0, false };
+static const struct acpi_gpio_params resetfw_gpio = { 2, 0, false };
+static const struct acpi_gpio_params wakeupfw = { 3, 0, false };
+static const struct acpi_gpio_mapping mei_vsc_acpi_gpios[] = {
+	{ "wakeuphost-gpios", &wakeuphost_gpio, 1 },
+	{ "wakeuphostint-gpios", &wakeuphostint_gpio, 1 },
+	{ "resetfw-gpios", &resetfw_gpio, 1 },
+	{ "wakeupfw-gpios", &wakeupfw, 1 },
+	{}
+};
+
+static struct acpi_device *find_cvfd_child_adev(struct acpi_device *parent)
+{
+	struct acpi_device *adev;
+
+	if (!parent)
+		return NULL;
+
+	list_for_each_entry (adev, &parent->children, node) {
+		if (!strcmp(CVFD_ACPI_ID_TGL, acpi_device_hid(adev)) ||
+		    !strcmp(CVFD_ACPI_ID_ADL, acpi_device_hid(adev)))
+			return adev;
+	}
+
+	return NULL;
+}
+
+static int get_sensor_name(struct mei_device *dev)
+{
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	struct spi_device *spi = hw->spi;
+	struct acpi_device *adev;
+	union acpi_object obj = { .type = ACPI_TYPE_INTEGER };
+	union acpi_object *ret_obj;
+	struct acpi_object_list arg_list = {
+		.count = 1,
+		.pointer = &obj,
+	};
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	acpi_status status;
+	char *c;
+
+	adev = find_cvfd_child_adev(ACPI_COMPANION(&spi->dev));
+	if (!adev) {
+		dev_err(&spi->dev, "ACPI not found CVFD device\n");
+		return -ENODEV;
+	}
+
+	obj.integer.value = LINK_NUMBER;
+	status = acpi_evaluate_object(adev->handle, METHOD_NAME_SID, &arg_list,
+				      &buffer);
+	if (ACPI_FAILURE(status)) {
+		dev_err(&spi->dev, "can't evaluate SID method: %d\n", status);
+		return -ENODEV;
+	}
+
+	ret_obj = buffer.pointer;
+	dev_dbg(&spi->dev, "SID status %d %lld %d - %d %s %d\n", status,
+		buffer.length, ret_obj->type, ret_obj->string.length,
+		ret_obj->string.pointer,
+		acpi_has_method(adev->handle, METHOD_NAME_SID));
+
+	if (ret_obj->string.length > sizeof(hw->cam_sensor_name)) {
+		ACPI_FREE(buffer.pointer);
+		return -EINVAL;
+	}
+	memcpy(hw->cam_sensor_name, ret_obj->string.pointer,
+	       ret_obj->string.length);
+
+	/* camera sensor name are all in lower case */
+	for (c = hw->cam_sensor_name; *c != '\0'; c++)
+		*c = tolower(*c);
+
+	ACPI_FREE(buffer.pointer);
+	return 0;
+}
+
+static int mei_vsc_probe(struct spi_device *spi)
+{
+	struct mei_vsc_hw *hw;
+	struct mei_device *dev;
+	int ret;
+
+	dev = mei_vsc_dev_init(&spi->dev);
+	if (!dev)
+		return -ENOMEM;
+
+	hw = to_vsc_hw(dev);
+	mutex_init(&hw->mutex);
+	init_waitqueue_head(&hw->xfer_wait);
+	hw->spi = spi;
+	spi_set_drvdata(spi, dev);
+
+	ret = get_sensor_name(dev);
+	if (ret)
+		return ret;
+
+	ret = devm_acpi_dev_add_driver_gpios(&spi->dev, mei_vsc_acpi_gpios);
+	if (ret) {
+		dev_err(&spi->dev, "%s: fail to add gpio\n", __func__);
+		return -EBUSY;
+	}
+
+	hw->wakeuphost = devm_gpiod_get(&spi->dev, "wakeuphost", GPIOD_IN);
+	if (IS_ERR(hw->wakeuphost)) {
+		dev_err(&spi->dev, "gpio get irq failed\n");
+		return -EINVAL;
+	}
+	hw->resetfw = devm_gpiod_get(&spi->dev, "resetfw", GPIOD_OUT_HIGH);
+	if (IS_ERR(hw->resetfw)) {
+		dev_err(&spi->dev, "gpio get resetfw failed\n");
+		return -EINVAL;
+	}
+	hw->wakeupfw = devm_gpiod_get(&spi->dev, "wakeupfw", GPIOD_OUT_HIGH);
+	if (IS_ERR(hw->wakeupfw)) {
+		dev_err(&spi->dev, "gpio get wakeupfw failed\n");
+		return -EINVAL;
+	}
+
+	ret = acpi_dev_gpio_irq_get_by(ACPI_COMPANION(&spi->dev),
+				       "wakeuphostint-gpios", 0);
+	if (ret < 0)
+		return ret;
+
+	hw->wakeuphostint = ret;
+	irq_set_status_flags(hw->wakeuphostint, IRQ_DISABLE_UNLAZY);
+	ret = request_threaded_irq(hw->wakeuphostint, mei_vsc_irq_quick_handler,
+				   mei_vsc_irq_thread_handler,
+				   IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+				   KBUILD_MODNAME, dev);
+	if (mei_start(dev)) {
+		dev_err(&spi->dev, "init hw failure.\n");
+		ret = -ENODEV;
+		goto release_irq;
+	}
+
+	ret = mei_register(dev, &spi->dev);
+	if (ret)
+		goto stop;
+
+	pm_runtime_enable(dev->dev);
+	dev_dbg(&spi->dev, "initialization successful.\n");
+	return 0;
+
+stop:
+	mei_stop(dev);
+release_irq:
+	mei_cancel_work(dev);
+	mei_disable_interrupts(dev);
+	free_irq(hw->wakeuphostint, dev);
+	return ret;
+}
+
+static int __maybe_unused mei_vsc_suspend(struct device *device)
+{
+	struct spi_device *spi = to_spi_device(device);
+	struct mei_device *dev = spi_get_drvdata(spi);
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	if (!dev)
+		return -ENODEV;
+
+	dev_dbg(dev->dev, "%s\n", __func__);
+
+	hw->disconnect = true;
+	mei_stop(dev);
+	mei_disable_interrupts(dev);
+	free_irq(hw->wakeuphostint, dev);
+	return 0;
+}
+
+static int __maybe_unused mei_vsc_resume(struct device *device)
+{
+	struct spi_device *spi = to_spi_device(device);
+	struct mei_device *dev = spi_get_drvdata(spi);
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+	int ret;
+
+	dev_dbg(dev->dev, "%s\n", __func__);
+	irq_set_status_flags(hw->wakeuphostint, IRQ_DISABLE_UNLAZY);
+	ret = request_threaded_irq(hw->wakeuphostint, mei_vsc_irq_quick_handler,
+				   mei_vsc_irq_thread_handler,
+				   IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+				   KBUILD_MODNAME, dev);
+	if (ret) {
+		dev_err(device, "request_threaded_irq failed: irq = %d.\n",
+			hw->wakeuphostint);
+		return ret;
+	}
+
+	hw->disconnect = false;
+	ret = mei_restart(dev);
+	if (ret)
+		return ret;
+
+	/* Start timer if stopped in suspend */
+	schedule_delayed_work(&dev->timer_work, HZ);
+	return 0;
+}
+
+static int mei_vsc_remove(struct spi_device *spi)
+{
+	struct mei_device *dev = spi_get_drvdata(spi);
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	dev_info(&spi->dev, "%s %d", __func__, hw->wakeuphostint);
+
+	pm_runtime_disable(dev->dev);
+	hw->disconnect = true;
+	mei_stop(dev);
+	mei_disable_interrupts(dev);
+	free_irq(hw->wakeuphostint, dev);
+	mei_deregister(dev);
+	mutex_destroy(&hw->mutex);
+	return 0;
+}
+
+/**
+ * mei_vsc_shutdown - Device Removal Routine
+ *
+ * @spi: SPI device structure
+ *
+ * mei_vsc_shutdown is called from the reboot notifier
+ * it's a simplified version of remove so we go down
+ * faster.
+ */
+static void mei_vsc_shutdown(struct spi_device *spi)
+{
+	struct mei_device *dev = spi_get_drvdata(spi);
+	struct mei_vsc_hw *hw = to_vsc_hw(dev);
+
+	dev_dbg(dev->dev, "shutdown\n");
+	hw->disconnect = true;
+	mei_stop(dev);
+
+	mei_disable_interrupts(dev);
+	free_irq(hw->wakeuphostint, dev);
+}
+
+static const struct dev_pm_ops mei_vsc_pm_ops = {
+
+	SET_SYSTEM_SLEEP_PM_OPS(mei_vsc_suspend, mei_vsc_resume)
+};
+
+static const struct acpi_device_id mei_vsc_acpi_ids[] = {
+	{ "INTC1058", 1 },
+	{ "INTC1094", 1 },
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, mei_vsc_acpi_ids);
+
+static struct spi_driver mei_vsc_driver = {
+	.driver = {
+		.name	= KBUILD_MODNAME,
+		.acpi_match_table = ACPI_PTR(mei_vsc_acpi_ids),
+		.pm		= &mei_vsc_pm_ops,
+	},
+	.probe		= mei_vsc_probe,
+	.remove		= mei_vsc_remove,
+	.shutdown = mei_vsc_shutdown,
+	.driver.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+};
+module_spi_driver(mei_vsc_driver);
+
+MODULE_AUTHOR("Ye Xiang <xiang.ye@intel.com>");
+MODULE_DESCRIPTION("Intel MEI VSC driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ocxl/config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ocxl/config.c
@@ -204,6 +204,18 @@
 	return 0;
 }
 
+/**
+ * get_dvsec_vendor0() - Find a related PCI device (function 0)
+ * @dev: PCI device to match
+ * @dev0: The PCI device (function 0) found
+ * @out_pos: The position of PCI device (function 0)
+ *
+ * Returns 0 on success, negative on failure.
+ *
+ * NOTE: If it's successful, the reference of dev0 is increased,
+ * so after using it, the callers must call pci_dev_put() to give
+ * up the reference.
+ */
 static int get_dvsec_vendor0(struct pci_dev *dev, struct pci_dev **dev0,
 			     int *out_pos)
 {
@@ -213,10 +225,14 @@
 		dev = get_function_0(dev);
 		if (!dev)
 			return -1;
+	} else {
+		dev = pci_dev_get(dev);
 	}
 	pos = find_dvsec(dev, OCXL_DVSEC_VENDOR_ID);
-	if (!pos)
+	if (!pos) {
+		pci_dev_put(dev);
 		return -1;
+	}
 	*dev0 = dev;
 	*out_pos = pos;
 	return 0;
@@ -233,6 +249,7 @@
 
 	pci_read_config_dword(dev0, pos + OCXL_DVSEC_VENDOR_RESET_RELOAD,
 			      &reset_reload);
+	pci_dev_put(dev0);
 	*val = !!(reset_reload & BIT(0));
 	return 0;
 }
@@ -254,6 +271,7 @@
 		reset_reload &= ~BIT(0);
 	pci_write_config_dword(dev0, pos + OCXL_DVSEC_VENDOR_RESET_RELOAD,
 			       reset_reload);
+	pci_dev_put(dev0);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ocxl/file.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ocxl/file.c
@@ -259,6 +259,8 @@
 		if (IS_ERR(ev_ctx))
 			return PTR_ERR(ev_ctx);
 		rc = ocxl_irq_set_handler(ctx, irq_id, irq_handler, irq_free, ev_ctx);
+		if (rc)
+			eventfd_ctx_put(ev_ctx);
 		break;
 
 	case OCXL_IOCTL_GET_METADATA:
@@ -541,8 +543,11 @@
 		goto err_put;
 
 	rc = device_register(&info->dev);
-	if (rc)
-		goto err_put;
+	if (rc) {
+		free_minor(info);
+		put_device(&info->dev);
+		return rc;
+	}
 
 	rc = ocxl_sysfs_register_afu(info);
 	if (rc)
@@ -558,7 +563,9 @@
 
 err_unregister:
 	ocxl_sysfs_unregister_afu(info); // safe to call even if register failed
+	free_minor(info);
 	device_unregister(&info->dev);
+	return rc;
 err_put:
 	ocxl_afu_put(afu);
 	free_minor(info);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/pci_endpoint_test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/pci_endpoint_test.c
@@ -71,6 +71,7 @@
 #define PCI_DEVICE_ID_TI_AM654			0xb00c
 #define PCI_DEVICE_ID_TI_J7200			0xb00f
 #define PCI_DEVICE_ID_TI_AM64			0xb010
+#define PCI_DEVICE_ID_TI_J721S2		0xb013
 #define PCI_DEVICE_ID_LS1088A			0x80c0
 
 #define is_am654_pci_dev(pdev)		\
@@ -80,6 +81,7 @@
 #define PCI_DEVICE_ID_RENESAS_R8A774B1		0x002b
 #define PCI_DEVICE_ID_RENESAS_R8A774C0		0x002d
 #define PCI_DEVICE_ID_RENESAS_R8A774E1		0x0025
+#define PCI_DEVICE_ID_RENESAS_R8A779F0		0x0031
 
 static DEFINE_IDA(pci_endpoint_test_ida);
 
@@ -332,6 +334,22 @@
 	return false;
 }
 
+static int pci_endpoint_test_validate_xfer_params(struct device *dev,
+		struct pci_endpoint_test_xfer_param *param, size_t alignment)
+{
+	if (!param->size) {
+		dev_dbg(dev, "Data size is zero\n");
+		return -EINVAL;
+	}
+
+	if (param->size > SIZE_MAX - alignment) {
+		dev_dbg(dev, "Maximum transfer data size exceeded\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static bool pci_endpoint_test_copy(struct pci_endpoint_test *test,
 				   unsigned long arg)
 {
@@ -363,9 +381,11 @@
 		return false;
 	}
 
+	err = pci_endpoint_test_validate_xfer_params(dev, &param, alignment);
+	if (err)
+		return false;
+
 	size = param.size;
-	if (size > SIZE_MAX - alignment)
-		goto err;
 
 	use_dma = !!(param.flags & PCITEST_FLAGS_USE_DMA);
 	if (use_dma)
@@ -497,9 +517,11 @@
 		return false;
 	}
 
+	err = pci_endpoint_test_validate_xfer_params(dev, &param, alignment);
+	if (err)
+		return false;
+
 	size = param.size;
-	if (size > SIZE_MAX - alignment)
-		goto err;
 
 	use_dma = !!(param.flags & PCITEST_FLAGS_USE_DMA);
 	if (use_dma)
@@ -595,9 +617,11 @@
 		return false;
 	}
 
+	err = pci_endpoint_test_validate_xfer_params(dev, &param, alignment);
+	if (err)
+		return false;
+
 	size = param.size;
-	if (size > SIZE_MAX - alignment)
-		goto err;
 
 	use_dma = !!(param.flags & PCITEST_FLAGS_USE_DMA);
 	if (use_dma)
@@ -706,6 +730,10 @@
 	struct pci_dev *pdev = test->pdev;
 
 	mutex_lock(&test->mutex);
+
+	reinit_completion(&test->irq_raised);
+	test->last_irq = -ENODATA;
+
 	switch (cmd) {
 	case PCITEST_BAR:
 		bar = arg;
@@ -915,6 +943,9 @@
 	if (id < 0)
 		return;
 
+	pci_endpoint_test_release_irq(test);
+	pci_endpoint_test_free_irq_vectors(test);
+
 	misc_deregister(&test->miscdev);
 	kfree(misc_device->name);
 	kfree(test->name);
@@ -924,9 +955,6 @@
 			pci_iounmap(pdev, test->bar[bar]);
 	}
 
-	pci_endpoint_test_release_irq(test);
-	pci_endpoint_test_free_irq_vectors(test);
-
 	pci_release_regions(pdev);
 	pci_disable_device(pdev);
 }
@@ -969,6 +997,9 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_RENESAS, PCI_DEVICE_ID_RENESAS_R8A774B1),},
 	{ PCI_DEVICE(PCI_VENDOR_ID_RENESAS, PCI_DEVICE_ID_RENESAS_R8A774C0),},
 	{ PCI_DEVICE(PCI_VENDOR_ID_RENESAS, PCI_DEVICE_ID_RENESAS_R8A774E1),},
+	{ PCI_DEVICE(PCI_VENDOR_ID_RENESAS, PCI_DEVICE_ID_RENESAS_R8A779F0),
+	  .driver_data = (kernel_ulong_t)&default_data,
+	},
 	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_J721E),
 	  .driver_data = (kernel_ulong_t)&j721e_data,
 	},
@@ -978,6 +1009,9 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_AM64),
 	  .driver_data = (kernel_ulong_t)&j721e_data,
 	},
+	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_J721S2),
+	  .driver_data = (kernel_ulong_t)&j721e_data,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(pci, pci_endpoint_test_tbl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/pvpanic/pvpanic-mmio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/pvpanic/pvpanic-mmio.c
@@ -24,53 +24,9 @@
 MODULE_DESCRIPTION("pvpanic-mmio device driver");
 MODULE_LICENSE("GPL");
 
-static ssize_t capability_show(struct device *dev,
-			       struct device_attribute *attr, char *buf)
-{
-	struct pvpanic_instance *pi = dev_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%x\n", pi->capability);
-}
-static DEVICE_ATTR_RO(capability);
-
-static ssize_t events_show(struct device *dev,  struct device_attribute *attr, char *buf)
-{
-	struct pvpanic_instance *pi = dev_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%x\n", pi->events);
-}
-
-static ssize_t events_store(struct device *dev,  struct device_attribute *attr,
-			    const char *buf, size_t count)
-{
-	struct pvpanic_instance *pi = dev_get_drvdata(dev);
-	unsigned int tmp;
-	int err;
-
-	err = kstrtouint(buf, 16, &tmp);
-	if (err)
-		return err;
-
-	if ((tmp & pi->capability) != tmp)
-		return -EINVAL;
-
-	pi->events = tmp;
-
-	return count;
-}
-static DEVICE_ATTR_RW(events);
-
-static struct attribute *pvpanic_mmio_dev_attrs[] = {
-	&dev_attr_capability.attr,
-	&dev_attr_events.attr,
-	NULL
-};
-ATTRIBUTE_GROUPS(pvpanic_mmio_dev);
-
 static int pvpanic_mmio_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	struct pvpanic_instance *pi;
 	struct resource *res;
 	void __iomem *base;
 
@@ -93,18 +49,7 @@
 		return -EINVAL;
 	}
 
-	pi = devm_kmalloc(dev, sizeof(*pi), GFP_KERNEL);
-	if (!pi)
-		return -ENOMEM;
-
-	pi->base = base;
-	pi->capability = PVPANIC_PANICKED | PVPANIC_CRASH_LOADED;
-
-	/* initlize capability by RDPT */
-	pi->capability &= ioread8(base);
-	pi->events = pi->capability;
-
-	return devm_pvpanic_probe(dev, pi);
+	return devm_pvpanic_probe(dev, base);
 }
 
 static const struct of_device_id pvpanic_mmio_match[] = {
@@ -124,7 +69,7 @@
 		.name = "pvpanic-mmio",
 		.of_match_table = pvpanic_mmio_match,
 		.acpi_match_table = pvpanic_device_ids,
-		.dev_groups = pvpanic_mmio_dev_groups,
+		.dev_groups = pvpanic_dev_groups,
 	},
 	.probe = pvpanic_mmio_probe,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/pvpanic/pvpanic-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/pvpanic/pvpanic-pci.c
@@ -19,61 +19,11 @@
 #define PCI_DEVICE_ID_REDHAT_PVPANIC     0x0011
 
 MODULE_AUTHOR("Mihai Carabas <mihai.carabas@oracle.com>");
-MODULE_DESCRIPTION("pvpanic device driver ");
+MODULE_DESCRIPTION("pvpanic device driver");
 MODULE_LICENSE("GPL");
 
-static const struct pci_device_id pvpanic_pci_id_tbl[]  = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_REDHAT, PCI_DEVICE_ID_REDHAT_PVPANIC)},
-	{}
-};
-
-static ssize_t capability_show(struct device *dev,
-			       struct device_attribute *attr, char *buf)
-{
-	struct pvpanic_instance *pi = dev_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%x\n", pi->capability);
-}
-static DEVICE_ATTR_RO(capability);
-
-static ssize_t events_show(struct device *dev,  struct device_attribute *attr, char *buf)
+static int pvpanic_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
-	struct pvpanic_instance *pi = dev_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%x\n", pi->events);
-}
-
-static ssize_t events_store(struct device *dev,  struct device_attribute *attr,
-			    const char *buf, size_t count)
-{
-	struct pvpanic_instance *pi = dev_get_drvdata(dev);
-	unsigned int tmp;
-	int err;
-
-	err = kstrtouint(buf, 16, &tmp);
-	if (err)
-		return err;
-
-	if ((tmp & pi->capability) != tmp)
-		return -EINVAL;
-
-	pi->events = tmp;
-
-	return count;
-}
-static DEVICE_ATTR_RW(events);
-
-static struct attribute *pvpanic_pci_dev_attrs[] = {
-	&dev_attr_capability.attr,
-	&dev_attr_events.attr,
-	NULL
-};
-ATTRIBUTE_GROUPS(pvpanic_pci_dev);
-
-static int pvpanic_pci_probe(struct pci_dev *pdev,
-			     const struct pci_device_id *ent)
-{
-	struct pvpanic_instance *pi;
 	void __iomem *base;
 	int ret;
 
@@ -85,29 +35,19 @@
 	if (!base)
 		return -ENOMEM;
 
-	pi = devm_kmalloc(&pdev->dev, sizeof(*pi), GFP_KERNEL);
-	if (!pi)
-		return -ENOMEM;
-
-	pi->base = base;
-	pi->capability = PVPANIC_PANICKED | PVPANIC_CRASH_LOADED;
-
-	/* initlize capability by RDPT */
-	pi->capability &= ioread8(base);
-	pi->events = pi->capability;
-
-	return devm_pvpanic_probe(&pdev->dev, pi);
+	return devm_pvpanic_probe(&pdev->dev, base);
 }
 
+static const struct pci_device_id pvpanic_pci_id_tbl[]  = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_REDHAT, PCI_DEVICE_ID_REDHAT_PVPANIC)},
+	{}
+};
+MODULE_DEVICE_TABLE(pci, pvpanic_pci_id_tbl);
+
 static struct pci_driver pvpanic_pci_driver = {
 	.name =         "pvpanic-pci",
 	.id_table =     pvpanic_pci_id_tbl,
 	.probe =        pvpanic_pci_probe,
-	.driver = {
-		.dev_groups = pvpanic_pci_dev_groups,
-	},
+	.dev_groups =   pvpanic_dev_groups,
 };
-
-MODULE_DEVICE_TABLE(pci, pvpanic_pci_id_tbl);
-
 module_pci_driver(pvpanic_pci_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/pvpanic/pvpanic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/pvpanic/pvpanic.c
@@ -7,6 +7,7 @@
  *  Copyright (C) 2021 Oracle.
  */
 
+#include <linux/device.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/kexec.h>
@@ -23,9 +24,16 @@
 #include "pvpanic.h"
 
 MODULE_AUTHOR("Mihai Carabas <mihai.carabas@oracle.com>");
-MODULE_DESCRIPTION("pvpanic device driver ");
+MODULE_DESCRIPTION("pvpanic device driver");
 MODULE_LICENSE("GPL");
 
+struct pvpanic_instance {
+	void __iomem *base;
+	unsigned int capability;
+	unsigned int events;
+	struct list_head list;
+};
+
 static struct list_head pvpanic_list;
 static spinlock_t pvpanic_lock;
 
@@ -34,7 +42,9 @@
 {
 	struct pvpanic_instance *pi_cur;
 
-	spin_lock(&pvpanic_lock);
+	if (!spin_trylock(&pvpanic_lock))
+		return;
+
 	list_for_each_entry(pi_cur, &pvpanic_list, list) {
 		if (event & pi_cur->capability & pi_cur->events)
 			iowrite8(event, pi_cur->base);
@@ -43,8 +53,7 @@
 }
 
 static int
-pvpanic_panic_notify(struct notifier_block *nb, unsigned long code,
-		     void *unused)
+pvpanic_panic_notify(struct notifier_block *nb, unsigned long code, void *unused)
 {
 	unsigned int event = PVPANIC_PANICKED;
 
@@ -56,9 +65,13 @@
 	return NOTIFY_DONE;
 }
 
+/*
+ * Call our notifier very early on panic, deferring the
+ * action taken to the hypervisor.
+ */
 static struct notifier_block pvpanic_panic_nb = {
 	.notifier_call = pvpanic_panic_notify,
-	.priority = 1, /* let this called before broken drm_fb_helper */
+	.priority = INT_MAX,
 };
 
 static void pvpanic_remove(void *param)
@@ -76,11 +89,75 @@
 	spin_unlock(&pvpanic_lock);
 }
 
-int devm_pvpanic_probe(struct device *dev, struct pvpanic_instance *pi)
+static ssize_t capability_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct pvpanic_instance *pi = dev_get_drvdata(dev);
+
+	return sysfs_emit(buf, "%x\n", pi->capability);
+}
+static DEVICE_ATTR_RO(capability);
+
+static ssize_t events_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct pvpanic_instance *pi = dev_get_drvdata(dev);
+
+	return sysfs_emit(buf, "%x\n", pi->events);
+}
+
+static ssize_t events_store(struct device *dev, struct device_attribute *attr,
+			    const char *buf, size_t count)
+{
+	struct pvpanic_instance *pi = dev_get_drvdata(dev);
+	unsigned int tmp;
+	int err;
+
+	err = kstrtouint(buf, 16, &tmp);
+	if (err)
+		return err;
+
+	if ((tmp & pi->capability) != tmp)
+		return -EINVAL;
+
+	pi->events = tmp;
+
+	return count;
+}
+static DEVICE_ATTR_RW(events);
+
+static struct attribute *pvpanic_dev_attrs[] = {
+	&dev_attr_capability.attr,
+	&dev_attr_events.attr,
+	NULL
+};
+
+static const struct attribute_group pvpanic_dev_group = {
+	.attrs = pvpanic_dev_attrs,
+};
+
+const struct attribute_group *pvpanic_dev_groups[] = {
+	&pvpanic_dev_group,
+	NULL
+};
+EXPORT_SYMBOL_GPL(pvpanic_dev_groups);
+
+int devm_pvpanic_probe(struct device *dev, void __iomem *base)
 {
-	if (!pi || !pi->base)
+	struct pvpanic_instance *pi;
+
+	if (!base)
 		return -EINVAL;
 
+	pi = devm_kmalloc(dev, sizeof(*pi), GFP_KERNEL);
+	if (!pi)
+		return -ENOMEM;
+
+	pi->base = base;
+	pi->capability = PVPANIC_PANICKED | PVPANIC_CRASH_LOADED;
+
+	/* initlize capability by RDPT */
+	pi->capability &= ioread8(base);
+	pi->events = pi->capability;
+
 	spin_lock(&pvpanic_lock);
 	list_add(&pi->list, &pvpanic_list);
 	spin_unlock(&pvpanic_lock);
@@ -96,18 +173,15 @@
 	INIT_LIST_HEAD(&pvpanic_list);
 	spin_lock_init(&pvpanic_lock);
 
-	atomic_notifier_chain_register(&panic_notifier_list,
-				       &pvpanic_panic_nb);
+	atomic_notifier_chain_register(&panic_notifier_list, &pvpanic_panic_nb);
 
 	return 0;
 }
+module_init(pvpanic_init);
 
 static void pvpanic_exit(void)
 {
-	atomic_notifier_chain_unregister(&panic_notifier_list,
-					 &pvpanic_panic_nb);
+	atomic_notifier_chain_unregister(&panic_notifier_list, &pvpanic_panic_nb);
 
 }
-
-module_init(pvpanic_init);
 module_exit(pvpanic_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/pvpanic/pvpanic.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/pvpanic/pvpanic.h
@@ -8,13 +8,7 @@
 #ifndef PVPANIC_H_
 #define PVPANIC_H_
 
-struct pvpanic_instance {
-	void __iomem *base;
-	unsigned int capability;
-	unsigned int events;
-	struct list_head list;
-};
-
-int devm_pvpanic_probe(struct device *dev, struct pvpanic_instance *pi);
+int devm_pvpanic_probe(struct device *dev, void __iomem *base);
+extern const struct attribute_group *pvpanic_dev_groups[];
 
 #endif /* PVPANIC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/sgi-gru/grufault.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/sgi-gru/grufault.c
@@ -648,6 +648,7 @@
 	if ((cb & (GRU_HANDLE_STRIDE - 1)) || ucbnum >= GRU_NUM_CB)
 		return -EINVAL;
 
+again:
 	gts = gru_find_lock_gts(cb);
 	if (!gts)
 		return -EINVAL;
@@ -656,7 +657,11 @@
 	if (ucbnum >= gts->ts_cbr_au_count * GRU_CBR_AU_SIZE)
 		goto exit;
 
-	gru_check_context_placement(gts);
+	if (gru_check_context_placement(gts)) {
+		gru_unlock_gts(gts);
+		gru_unload_context(gts, 1);
+		goto again;
+	}
 
 	/*
 	 * CCH may contain stale data if ts_force_cch_reload is set.
@@ -874,7 +879,11 @@
 		} else {
 			gts->ts_user_blade_id = req.val1;
 			gts->ts_user_chiplet_id = req.val0;
-			gru_check_context_placement(gts);
+			if (gru_check_context_placement(gts)) {
+				gru_unlock_gts(gts);
+				gru_unload_context(gts, 1);
+				return ret;
+			}
 		}
 		break;
 	case sco_gseg_owner:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/sgi-gru/grukservices.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/sgi-gru/grukservices.c
@@ -258,7 +258,6 @@
 	int lcpu;
 
 	BUG_ON(dsr_bytes > GRU_NUM_KERNEL_DSR_BYTES);
-	preempt_disable();
 	bs = gru_lock_kernel_context(-1);
 	lcpu = uv_blade_processor_id();
 	*cb = bs->kernel_cb + lcpu * GRU_HANDLE_STRIDE;
@@ -272,7 +271,6 @@
 static void gru_free_cpu_resources(void *cb, void *dsr)
 {
 	gru_unlock_kernel_context(uv_numa_blade_id());
-	preempt_enable();
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/sgi-gru/grumain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/sgi-gru/grumain.c
@@ -716,9 +716,10 @@
  * chiplet. Misassignment can occur if the process migrates to a different
  * blade or if the user changes the selected blade/chiplet.
  */
-void gru_check_context_placement(struct gru_thread_state *gts)
+int gru_check_context_placement(struct gru_thread_state *gts)
 {
 	struct gru_state *gru;
+	int ret = 0;
 
 	/*
 	 * If the current task is the context owner, verify that the
@@ -726,15 +727,23 @@
 	 * references. Pthread apps use non-owner references to the CBRs.
 	 */
 	gru = gts->ts_gru;
+	/*
+	 * If gru or gts->ts_tgid_owner isn't initialized properly, return
+	 * success to indicate that the caller does not need to unload the
+	 * gru context.The caller is responsible for their inspection and
+	 * reinitialization if needed.
+	 */
 	if (!gru || gts->ts_tgid_owner != current->tgid)
-		return;
+		return ret;
 
 	if (!gru_check_chiplet_assignment(gru, gts)) {
 		STAT(check_context_unload);
-		gru_unload_context(gts, 1);
+		ret = -EINVAL;
 	} else if (gru_retarget_intr(gts)) {
 		STAT(check_context_retarget_intr);
 	}
+
+	return ret;
 }
 
 
@@ -932,14 +941,16 @@
 
 again:
 	mutex_lock(&gts->ts_ctxlock);
-	preempt_disable();
 
-	gru_check_context_placement(gts);
+	if (gru_check_context_placement(gts)) {
+		mutex_unlock(&gts->ts_ctxlock);
+		gru_unload_context(gts, 1);
+		return VM_FAULT_NOPAGE;
+	}
 
 	if (!gts->ts_gru) {
 		STAT(load_user_context);
 		if (!gru_assign_gru_context(gts)) {
-			preempt_enable();
 			mutex_unlock(&gts->ts_ctxlock);
 			set_current_state(TASK_INTERRUPTIBLE);
 			schedule_timeout(GRU_ASSIGN_DELAY);  /* true hack ZZZ */
@@ -955,7 +966,6 @@
 				vma->vm_page_prot);
 	}
 
-	preempt_enable();
 	mutex_unlock(&gts->ts_ctxlock);
 
 	return VM_FAULT_NOPAGE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/sgi-gru/grutables.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/sgi-gru/grutables.h
@@ -638,7 +638,7 @@
 extern int gru_user_unload_context(unsigned long arg);
 extern int gru_get_exception_detail(unsigned long arg);
 extern int gru_set_context_option(unsigned long address);
-extern void gru_check_context_placement(struct gru_thread_state *gts);
+extern int gru_check_context_placement(struct gru_thread_state *gts);
 extern int gru_cpu_fault_map_id(void);
 extern struct vm_area_struct *gru_find_vma(unsigned long vaddr);
 extern void gru_flush_all_tlb(struct gru_state *gru);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/sgi-gru/grutlbpurge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/sgi-gru/grutlbpurge.c
@@ -65,7 +65,6 @@
 	struct gru_tlb_global_handle *tgh;
 	int n;
 
-	preempt_disable();
 	if (uv_numa_blade_id() == gru->gs_blade_id)
 		n = get_on_blade_tgh(gru);
 	else
@@ -79,7 +78,6 @@
 static void get_unlock_tgh_handle(struct gru_tlb_global_handle *tgh)
 {
 	unlock_tgh_handle(tgh);
-	preempt_enable();
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/ti-st/st_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/ti-st/st_core.c
@@ -15,6 +15,7 @@
 #include <linux/skbuff.h>
 
 #include <linux/ti_wilink_st.h>
+#include <linux/netdevice.h>
 
 extern void st_kim_recv(void *, const unsigned char *, long);
 void st_int_recv(void *, const unsigned char *, long);
@@ -435,7 +436,7 @@
 	case ST_LL_AWAKE_TO_ASLEEP:
 		pr_err("ST LL is illegal state(%ld),"
 			   "purging received skb.", st_ll_getstate(st_gdata));
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 		break;
 	case ST_LL_ASLEEP:
 		skb_queue_tail(&st_gdata->tx_waitq, skb);
@@ -444,7 +445,7 @@
 	default:
 		pr_err("ST LL is illegal state(%ld),"
 			   "purging received skb.", st_ll_getstate(st_gdata));
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 		break;
 	}
 
@@ -498,7 +499,7 @@
 				spin_unlock_irqrestore(&st_data->lock, flags);
 				break;
 			}
-			kfree_skb(skb);
+			dev_kfree_skb_irq(skb);
 			spin_unlock_irqrestore(&st_data->lock, flags);
 		}
 		/* if wake-up is set in another context- restart sending */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/tifm_7xx1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/tifm_7xx1.c
@@ -190,7 +190,7 @@
 				spin_unlock_irqrestore(&fm->lock, flags);
 			}
 			if (sock)
-				tifm_free_device(&sock->dev);
+				put_device(&sock->dev);
 		}
 		spin_lock_irqsave(&fm->lock, flags);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/uacce/uacce.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/uacce/uacce.c
@@ -9,43 +9,38 @@
 
 static struct class *uacce_class;
 static dev_t uacce_devt;
-static DEFINE_MUTEX(uacce_mutex);
 static DEFINE_XARRAY_ALLOC(uacce_xa);
 
-static int uacce_start_queue(struct uacce_queue *q)
+/*
+ * If the parent driver or the device disappears, the queue state is invalid and
+ * ops are not usable anymore.
+ */
+static bool uacce_queue_is_valid(struct uacce_queue *q)
 {
-	int ret = 0;
+	return q->state == UACCE_Q_INIT || q->state == UACCE_Q_STARTED;
+}
 
-	mutex_lock(&uacce_mutex);
+static int uacce_start_queue(struct uacce_queue *q)
+{
+	int ret;
 
-	if (q->state != UACCE_Q_INIT) {
-		ret = -EINVAL;
-		goto out_with_lock;
-	}
+	if (q->state != UACCE_Q_INIT)
+		return -EINVAL;
 
 	if (q->uacce->ops->start_queue) {
 		ret = q->uacce->ops->start_queue(q);
 		if (ret < 0)
-			goto out_with_lock;
+			return ret;
 	}
 
 	q->state = UACCE_Q_STARTED;
-
-out_with_lock:
-	mutex_unlock(&uacce_mutex);
-
-	return ret;
+	return 0;
 }
 
 static int uacce_put_queue(struct uacce_queue *q)
 {
 	struct uacce_device *uacce = q->uacce;
 
-	mutex_lock(&uacce_mutex);
-
-	if (q->state == UACCE_Q_ZOMBIE)
-		goto out;
-
 	if ((q->state == UACCE_Q_STARTED) && uacce->ops->stop_queue)
 		uacce->ops->stop_queue(q);
 
@@ -54,8 +49,6 @@
 		uacce->ops->put_queue(q);
 
 	q->state = UACCE_Q_ZOMBIE;
-out:
-	mutex_unlock(&uacce_mutex);
 
 	return 0;
 }
@@ -65,20 +58,36 @@
 {
 	struct uacce_queue *q = filep->private_data;
 	struct uacce_device *uacce = q->uacce;
+	long ret = -ENXIO;
+
+	/*
+	 * uacce->ops->ioctl() may take the mmap_lock when copying arg to/from
+	 * user. Avoid a circular lock dependency with uacce_fops_mmap(), which
+	 * gets called with mmap_lock held, by taking uacce->mutex instead of
+	 * q->mutex. Doing this in uacce_fops_mmap() is not possible because
+	 * uacce_fops_open() calls iommu_sva_bind_device(), which takes
+	 * mmap_lock, while holding uacce->mutex.
+	 */
+	mutex_lock(&uacce->mutex);
+	if (!uacce_queue_is_valid(q))
+		goto out_unlock;
 
 	switch (cmd) {
 	case UACCE_CMD_START_Q:
-		return uacce_start_queue(q);
-
+		ret = uacce_start_queue(q);
+		break;
 	case UACCE_CMD_PUT_Q:
-		return uacce_put_queue(q);
-
+		ret = uacce_put_queue(q);
+		break;
 	default:
-		if (!uacce->ops->ioctl)
-			return -EINVAL;
-
-		return uacce->ops->ioctl(q, cmd, arg);
+		if (uacce->ops->ioctl)
+			ret = uacce->ops->ioctl(q, cmd, arg);
+		else
+			ret = -EINVAL;
 	}
+out_unlock:
+	mutex_unlock(&uacce->mutex);
+	return ret;
 }
 
 #ifdef CONFIG_COMPAT
@@ -136,6 +145,13 @@
 	if (!q)
 		return -ENOMEM;
 
+	mutex_lock(&uacce->mutex);
+
+	if (!uacce->parent) {
+		ret = -EINVAL;
+		goto out_with_mem;
+	}
+
 	ret = uacce_bind_queue(uacce, q);
 	if (ret)
 		goto out_with_mem;
@@ -152,10 +168,9 @@
 	filep->private_data = q;
 	uacce->inode = inode;
 	q->state = UACCE_Q_INIT;
-
-	mutex_lock(&uacce->queues_lock);
+	mutex_init(&q->mutex);
 	list_add(&q->list, &uacce->queues);
-	mutex_unlock(&uacce->queues_lock);
+	mutex_unlock(&uacce->mutex);
 
 	return 0;
 
@@ -163,18 +178,20 @@
 	uacce_unbind_queue(q);
 out_with_mem:
 	kfree(q);
+	mutex_unlock(&uacce->mutex);
 	return ret;
 }
 
 static int uacce_fops_release(struct inode *inode, struct file *filep)
 {
 	struct uacce_queue *q = filep->private_data;
+	struct uacce_device *uacce = q->uacce;
 
-	mutex_lock(&q->uacce->queues_lock);
-	list_del(&q->list);
-	mutex_unlock(&q->uacce->queues_lock);
+	mutex_lock(&uacce->mutex);
 	uacce_put_queue(q);
 	uacce_unbind_queue(q);
+	list_del(&q->list);
+	mutex_unlock(&uacce->mutex);
 	kfree(q);
 
 	return 0;
@@ -217,10 +234,9 @@
 	vma->vm_private_data = q;
 	qfr->type = type;
 
-	mutex_lock(&uacce_mutex);
-
-	if (q->state != UACCE_Q_INIT && q->state != UACCE_Q_STARTED) {
-		ret = -EINVAL;
+	mutex_lock(&q->mutex);
+	if (!uacce_queue_is_valid(q)) {
+		ret = -ENXIO;
 		goto out_with_lock;
 	}
 
@@ -248,12 +264,12 @@
 	}
 
 	q->qfrs[type] = qfr;
-	mutex_unlock(&uacce_mutex);
+	mutex_unlock(&q->mutex);
 
 	return ret;
 
 out_with_lock:
-	mutex_unlock(&uacce_mutex);
+	mutex_unlock(&q->mutex);
 	kfree(qfr);
 	return ret;
 }
@@ -262,12 +278,20 @@
 {
 	struct uacce_queue *q = file->private_data;
 	struct uacce_device *uacce = q->uacce;
+	__poll_t ret = 0;
+
+	mutex_lock(&q->mutex);
+	if (!uacce_queue_is_valid(q))
+		goto out_unlock;
 
 	poll_wait(file, &q->wait, wait);
+
 	if (uacce->ops->is_q_updated && uacce->ops->is_q_updated(q))
-		return EPOLLIN | EPOLLRDNORM;
+		ret = EPOLLIN | EPOLLRDNORM;
 
-	return 0;
+out_unlock:
+	mutex_unlock(&q->mutex);
+	return ret;
 }
 
 static const struct file_operations uacce_fops = {
@@ -450,7 +474,7 @@
 		goto err_with_uacce;
 
 	INIT_LIST_HEAD(&uacce->queues);
-	mutex_init(&uacce->queues_lock);
+	mutex_init(&uacce->mutex);
 	device_initialize(&uacce->dev);
 	uacce->dev.devt = MKDEV(MAJOR(uacce_devt), uacce->dev_id);
 	uacce->dev.class = uacce_class;
@@ -507,13 +531,23 @@
 	if (uacce->inode)
 		unmap_mapping_range(uacce->inode->i_mapping, 0, 0, 1);
 
+	/*
+	 * uacce_fops_open() may be running concurrently, even after we remove
+	 * the cdev. Holding uacce->mutex ensures that open() does not obtain a
+	 * removed uacce device.
+	 */
+	mutex_lock(&uacce->mutex);
 	/* ensure no open queue remains */
-	mutex_lock(&uacce->queues_lock);
 	list_for_each_entry_safe(q, next_q, &uacce->queues, list) {
+		/*
+		 * Taking q->mutex ensures that fops do not use the defunct
+		 * uacce->ops after the queue is disabled.
+		 */
+		mutex_lock(&q->mutex);
 		uacce_put_queue(q);
+		mutex_unlock(&q->mutex);
 		uacce_unbind_queue(q);
 	}
-	mutex_unlock(&uacce->queues_lock);
 
 	/* disable sva now since no opened queues */
 	uacce_disable_sva(uacce);
@@ -521,6 +555,13 @@
 	if (uacce->cdev)
 		cdev_device_del(uacce->cdev, &uacce->dev);
 	xa_erase(&uacce_xa, uacce->dev_id);
+	/*
+	 * uacce exists as long as there are open fds, but ops will be freed
+	 * now. Ensure that bugs cause NULL deref rather than use-after-free.
+	 */
+	uacce->ops = NULL;
+	uacce->parent = NULL;
+	mutex_unlock(&uacce->mutex);
 	put_device(&uacce->dev);
 }
 EXPORT_SYMBOL_GPL(uacce_remove);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_balloon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_balloon.c
@@ -1711,7 +1711,7 @@
 static void __exit vmballoon_debugfs_exit(struct vmballoon *b)
 {
 	static_key_disable(&balloon_stat_enabled.key);
-	debugfs_remove(debugfs_lookup("vmmemctl", NULL));
+	debugfs_lookup_and_remove("vmmemctl", NULL);
 	kfree(b->stats);
 	b->stats = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/Kconfig
@@ -5,7 +5,7 @@
 
 config VMWARE_VMCI
 	tristate "VMware VMCI Driver"
-	depends on X86 && PCI
+	depends on (X86 || ARM64) && !CPU_BIG_ENDIAN && PCI
 	help
 	  This is VMware's Virtual Machine Communication Interface.  It enables
 	  high-speed communication between host and guest in a virtual
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/vmci_datagram.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/vmci_datagram.c
@@ -234,7 +234,8 @@
 
 			dg_info->in_dg_host_queue = true;
 			dg_info->entry = dst_entry;
-			memcpy(&dg_info->msg, dg, dg_size);
+			dg_info->msg = *dg;
+			memcpy(&dg_info->msg_payload, dg + 1, dg->payload_size);
 
 			INIT_WORK(&dg_info->work, dg_delayed_dispatch);
 			schedule_work(&dg_info->work);
@@ -377,7 +378,8 @@
 
 		dg_info->in_dg_host_queue = false;
 		dg_info->entry = dst_entry;
-		memcpy(&dg_info->msg, dg, VMCI_DG_SIZE(dg));
+		dg_info->msg = *dg;
+		memcpy(&dg_info->msg_payload, dg + 1, dg->payload_size);
 
 		INIT_WORK(&dg_info->work, dg_delayed_dispatch);
 		schedule_work(&dg_info->work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/vmci_event.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/vmci_event.c
@@ -9,6 +9,7 @@
 #include <linux/vmw_vmci_api.h>
 #include <linux/list.h>
 #include <linux/module.h>
+#include <linux/nospec.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/rculist.h>
@@ -86,9 +87,12 @@
 {
 	struct vmci_subscription *cur;
 	struct list_head *subscriber_list;
+	u32 sanitized_event, max_vmci_event;
 
 	rcu_read_lock();
-	subscriber_list = &subscriber_array[event_msg->event_data.event];
+	max_vmci_event = ARRAY_SIZE(subscriber_array);
+	sanitized_event = array_index_nospec(event_msg->event_data.event, max_vmci_event);
+	subscriber_list = &subscriber_array[sanitized_event];
 	list_for_each_entry_rcu(cur, subscriber_list, node) {
 		cur->callback(cur->id, &event_msg->event_data,
 			      cur->callback_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/vmci_guest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/vmci_guest.c
@@ -13,6 +13,7 @@
 #include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/module.h>
+#include <linux/processor.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/init.h>
@@ -31,6 +32,12 @@
 
 #define VMCI_UTIL_NUM_RESOURCES 1
 
+/*
+ * Datagram buffers for DMA send/receive must accommodate at least
+ * a maximum sized datagram and the header.
+ */
+#define VMCI_DMA_DG_BUFFER_SIZE (VMCI_MAX_DG_SIZE + PAGE_SIZE)
+
 static bool vmci_disable_msi;
 module_param_named(disable_msi, vmci_disable_msi, bool, 0);
 MODULE_PARM_DESC(disable_msi, "Disable MSI use in driver - (default=0)");
@@ -45,13 +52,18 @@
 struct vmci_guest_device {
 	struct device *dev;	/* PCI device we are attached to */
 	void __iomem *iobase;
+	void __iomem *mmio_base;
 
 	bool exclusive_vectors;
 
 	struct tasklet_struct datagram_tasklet;
 	struct tasklet_struct bm_tasklet;
+	struct wait_queue_head inout_wq;
 
 	void *data_buffer;
+	dma_addr_t data_buffer_base;
+	void *tx_buffer;
+	dma_addr_t tx_buffer_base;
 	void *notification_bitmap;
 	dma_addr_t notification_base;
 };
@@ -89,6 +101,92 @@
 	return vm_context_id;
 }
 
+static unsigned int vmci_read_reg(struct vmci_guest_device *dev, u32 reg)
+{
+	if (dev->mmio_base != NULL)
+		return readl(dev->mmio_base + reg);
+	return ioread32(dev->iobase + reg);
+}
+
+static void vmci_write_reg(struct vmci_guest_device *dev, u32 val, u32 reg)
+{
+	if (dev->mmio_base != NULL)
+		writel(val, dev->mmio_base + reg);
+	else
+		iowrite32(val, dev->iobase + reg);
+}
+
+static void vmci_read_data(struct vmci_guest_device *vmci_dev,
+			   void *dest, size_t size)
+{
+	if (vmci_dev->mmio_base == NULL)
+		ioread8_rep(vmci_dev->iobase + VMCI_DATA_IN_ADDR,
+			    dest, size);
+	else {
+		/*
+		 * For DMA datagrams, the data_buffer will contain the header on the
+		 * first page, followed by the incoming datagram(s) on the following
+		 * pages. The header uses an S/G element immediately following the
+		 * header on the first page to point to the data area.
+		 */
+		struct vmci_data_in_out_header *buffer_header = vmci_dev->data_buffer;
+		struct vmci_sg_elem *sg_array = (struct vmci_sg_elem *)(buffer_header + 1);
+		size_t buffer_offset = dest - vmci_dev->data_buffer;
+
+		buffer_header->opcode = 1;
+		buffer_header->size = 1;
+		buffer_header->busy = 0;
+		sg_array[0].addr = vmci_dev->data_buffer_base + buffer_offset;
+		sg_array[0].size = size;
+
+		vmci_write_reg(vmci_dev, lower_32_bits(vmci_dev->data_buffer_base),
+			       VMCI_DATA_IN_LOW_ADDR);
+
+		wait_event(vmci_dev->inout_wq, buffer_header->busy == 1);
+	}
+}
+
+static int vmci_write_data(struct vmci_guest_device *dev,
+			   struct vmci_datagram *dg)
+{
+	int result;
+
+	if (dev->mmio_base != NULL) {
+		struct vmci_data_in_out_header *buffer_header = dev->tx_buffer;
+		u8 *dg_out_buffer = (u8 *)(buffer_header + 1);
+
+		if (VMCI_DG_SIZE(dg) > VMCI_MAX_DG_SIZE)
+			return VMCI_ERROR_INVALID_ARGS;
+
+		/*
+		 * Initialize send buffer with outgoing datagram
+		 * and set up header for inline data. Device will
+		 * not access buffer asynchronously - only after
+		 * the write to VMCI_DATA_OUT_LOW_ADDR.
+		 */
+		memcpy(dg_out_buffer, dg, VMCI_DG_SIZE(dg));
+		buffer_header->opcode = 0;
+		buffer_header->size = VMCI_DG_SIZE(dg);
+		buffer_header->busy = 1;
+
+		vmci_write_reg(dev, lower_32_bits(dev->tx_buffer_base),
+			       VMCI_DATA_OUT_LOW_ADDR);
+
+		/* Caller holds a spinlock, so cannot block. */
+		spin_until_cond(buffer_header->busy == 0);
+
+		result = vmci_read_reg(vmci_dev_g, VMCI_RESULT_LOW_ADDR);
+		if (result == VMCI_SUCCESS)
+			result = (int)buffer_header->result;
+	} else {
+		iowrite8_rep(dev->iobase + VMCI_DATA_OUT_ADDR,
+			     dg, VMCI_DG_SIZE(dg));
+		result = vmci_read_reg(vmci_dev_g, VMCI_RESULT_LOW_ADDR);
+	}
+
+	return result;
+}
+
 /*
  * VM to hypervisor call mechanism. We use the standard VMware naming
  * convention since shared code is calling this function as well.
@@ -114,9 +212,8 @@
 	spin_lock_irqsave(&vmci_dev_spinlock, flags);
 
 	if (vmci_dev_g) {
-		iowrite8_rep(vmci_dev_g->iobase + VMCI_DATA_OUT_ADDR,
-			     dg, VMCI_DG_SIZE(dg));
-		result = ioread32(vmci_dev_g->iobase + VMCI_RESULT_LOW_ADDR);
+		vmci_write_data(vmci_dev_g, dg);
+		result = vmci_read_reg(vmci_dev_g, VMCI_RESULT_LOW_ADDR);
 	} else {
 		result = VMCI_ERROR_UNAVAILABLE;
 	}
@@ -195,15 +292,17 @@
 }
 
 /*
- * Reads datagrams from the data in port and dispatches them. We
- * always start reading datagrams into only the first page of the
- * datagram buffer. If the datagrams don't fit into one page, we
- * use the maximum datagram buffer size for the remainder of the
- * invocation. This is a simple heuristic for not penalizing
- * small datagrams.
+ * Reads datagrams from the device and dispatches them. For IO port
+ * based access to the device, we always start reading datagrams into
+ * only the first page of the datagram buffer. If the datagrams don't
+ * fit into one page, we use the maximum datagram buffer size for the
+ * remainder of the invocation. This is a simple heuristic for not
+ * penalizing small datagrams. For DMA-based datagrams, we always
+ * use the maximum datagram buffer size, since there is no performance
+ * penalty for doing so.
  *
  * This function assumes that it has exclusive access to the data
- * in port for the duration of the call.
+ * in register(s) for the duration of the call.
  */
 static void vmci_dispatch_dgs(unsigned long data)
 {
@@ -211,23 +310,41 @@
 	u8 *dg_in_buffer = vmci_dev->data_buffer;
 	struct vmci_datagram *dg;
 	size_t dg_in_buffer_size = VMCI_MAX_DG_SIZE;
-	size_t current_dg_in_buffer_size = PAGE_SIZE;
+	size_t current_dg_in_buffer_size;
 	size_t remaining_bytes;
+	bool is_io_port = vmci_dev->mmio_base == NULL;
 
 	BUILD_BUG_ON(VMCI_MAX_DG_SIZE < PAGE_SIZE);
 
-	ioread8_rep(vmci_dev->iobase + VMCI_DATA_IN_ADDR,
-		    vmci_dev->data_buffer, current_dg_in_buffer_size);
+	if (!is_io_port) {
+		/* For mmio, the first page is used for the header. */
+		dg_in_buffer += PAGE_SIZE;
+
+		/*
+		 * For DMA-based datagram operations, there is no performance
+		 * penalty for reading the maximum buffer size.
+		 */
+		current_dg_in_buffer_size = VMCI_MAX_DG_SIZE;
+	} else {
+		current_dg_in_buffer_size = PAGE_SIZE;
+	}
+	vmci_read_data(vmci_dev, dg_in_buffer, current_dg_in_buffer_size);
 	dg = (struct vmci_datagram *)dg_in_buffer;
 	remaining_bytes = current_dg_in_buffer_size;
 
+	/*
+	 * Read through the buffer until an invalid datagram header is
+	 * encountered. The exit condition for datagrams read through
+	 * VMCI_DATA_IN_ADDR is a bit more complicated, since a datagram
+	 * can start on any page boundary in the buffer.
+	 */
 	while (dg->dst.resource != VMCI_INVALID_ID ||
-	       remaining_bytes > PAGE_SIZE) {
+	       (is_io_port && remaining_bytes > PAGE_SIZE)) {
 		unsigned dg_in_size;
 
 		/*
-		 * When the input buffer spans multiple pages, a datagram can
-		 * start on any page boundary in the buffer.
+		 * If using VMCI_DATA_IN_ADDR, skip to the next page
+		 * as a datagram can start on any page boundary.
 		 */
 		if (dg->dst.resource == VMCI_INVALID_ID) {
 			dg = (struct vmci_datagram *)roundup(
@@ -277,11 +394,10 @@
 					current_dg_in_buffer_size =
 					    dg_in_buffer_size;
 
-				ioread8_rep(vmci_dev->iobase +
-						VMCI_DATA_IN_ADDR,
-					vmci_dev->data_buffer +
+				vmci_read_data(vmci_dev,
+					       dg_in_buffer +
 						remaining_bytes,
-					current_dg_in_buffer_size -
+					       current_dg_in_buffer_size -
 						remaining_bytes);
 			}
 
@@ -319,10 +435,8 @@
 				current_dg_in_buffer_size = dg_in_buffer_size;
 
 			for (;;) {
-				ioread8_rep(vmci_dev->iobase +
-						VMCI_DATA_IN_ADDR,
-					vmci_dev->data_buffer,
-					current_dg_in_buffer_size);
+				vmci_read_data(vmci_dev, dg_in_buffer,
+					       current_dg_in_buffer_size);
 				if (bytes_to_skip <= current_dg_in_buffer_size)
 					break;
 
@@ -339,8 +453,7 @@
 		if (remaining_bytes < VMCI_DG_HEADERSIZE) {
 			/* Get the next batch of datagrams. */
 
-			ioread8_rep(vmci_dev->iobase + VMCI_DATA_IN_ADDR,
-				    vmci_dev->data_buffer,
+			vmci_read_data(vmci_dev, dg_in_buffer,
 				    current_dg_in_buffer_size);
 			dg = (struct vmci_datagram *)dg_in_buffer;
 			remaining_bytes = current_dg_in_buffer_size;
@@ -384,7 +497,7 @@
 		unsigned int icr;
 
 		/* Acknowledge interrupt and determine what needs doing. */
-		icr = ioread32(dev->iobase + VMCI_ICR_ADDR);
+		icr = vmci_read_reg(dev, VMCI_ICR_ADDR);
 		if (icr == 0 || icr == ~0)
 			return IRQ_NONE;
 
@@ -398,6 +511,12 @@
 			icr &= ~VMCI_ICR_NOTIFICATION;
 		}
 
+
+		if (icr & VMCI_ICR_DMA_DATAGRAM) {
+			wake_up_all(&dev->inout_wq);
+			icr &= ~VMCI_ICR_DMA_DATAGRAM;
+		}
+
 		if (icr != 0)
 			dev_warn(dev->dev,
 				 "Ignoring unknown interrupt cause (%d)\n",
@@ -423,13 +542,47 @@
 }
 
 /*
+ * Interrupt handler for MSI-X interrupt vector VMCI_INTR_DMA_DATAGRAM,
+ * which is for the completion of a DMA datagram send or receive operation.
+ * Will only get called if we are using MSI-X with exclusive vectors.
+ */
+static irqreturn_t vmci_interrupt_dma_datagram(int irq, void *_dev)
+{
+	struct vmci_guest_device *dev = _dev;
+
+	wake_up_all(&dev->inout_wq);
+
+	return IRQ_HANDLED;
+}
+
+static void vmci_free_dg_buffers(struct vmci_guest_device *vmci_dev)
+{
+	if (vmci_dev->mmio_base != NULL) {
+		if (vmci_dev->tx_buffer != NULL)
+			dma_free_coherent(vmci_dev->dev,
+					  VMCI_DMA_DG_BUFFER_SIZE,
+					  vmci_dev->tx_buffer,
+					  vmci_dev->tx_buffer_base);
+		if (vmci_dev->data_buffer != NULL)
+			dma_free_coherent(vmci_dev->dev,
+					  VMCI_DMA_DG_BUFFER_SIZE,
+					  vmci_dev->data_buffer,
+					  vmci_dev->data_buffer_base);
+	} else {
+		vfree(vmci_dev->data_buffer);
+	}
+}
+
+/*
  * Most of the initialization at module load time is done here.
  */
 static int vmci_guest_probe_device(struct pci_dev *pdev,
 				   const struct pci_device_id *id)
 {
 	struct vmci_guest_device *vmci_dev;
-	void __iomem *iobase;
+	void __iomem *iobase = NULL;
+	void __iomem *mmio_base = NULL;
+	unsigned int num_irq_vectors;
 	unsigned int capabilities;
 	unsigned int caps_in_use;
 	unsigned long cmd;
@@ -445,17 +598,34 @@
 		return error;
 	}
 
-	error = pcim_iomap_regions(pdev, 1 << 0, KBUILD_MODNAME);
-	if (error) {
-		dev_err(&pdev->dev, "Failed to reserve/map IO regions\n");
-		return error;
+	/*
+	 * The VMCI device with mmio access to registers requests 256KB
+	 * for BAR1. If present, driver will use new VMCI device
+	 * functionality for register access and datagram send/recv.
+	 */
+
+	if (pci_resource_len(pdev, 1) == VMCI_WITH_MMIO_ACCESS_BAR_SIZE) {
+		dev_info(&pdev->dev, "MMIO register access is available\n");
+		mmio_base = pci_iomap_range(pdev, 1, VMCI_MMIO_ACCESS_OFFSET,
+					    VMCI_MMIO_ACCESS_SIZE);
+		/* If the map fails, we fall back to IOIO access. */
+		if (!mmio_base)
+			dev_warn(&pdev->dev, "Failed to map MMIO register access\n");
+	}
+
+	if (!mmio_base) {
+		if (IS_ENABLED(CONFIG_ARM64)) {
+			dev_err(&pdev->dev, "MMIO base is invalid\n");
+			return -ENXIO;
+		}
+		error = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
+		if (error) {
+			dev_err(&pdev->dev, "Failed to reserve/map IO regions\n");
+			return error;
+		}
+		iobase = pcim_iomap_table(pdev)[0];
 	}
 
-	iobase = pcim_iomap_table(pdev)[0];
-
-	dev_info(&pdev->dev, "Found VMCI PCI device at %#lx, irq %u\n",
-		 (unsigned long)iobase, pdev->irq);
-
 	vmci_dev = devm_kzalloc(&pdev->dev, sizeof(*vmci_dev), GFP_KERNEL);
 	if (!vmci_dev) {
 		dev_err(&pdev->dev,
@@ -466,17 +636,35 @@
 	vmci_dev->dev = &pdev->dev;
 	vmci_dev->exclusive_vectors = false;
 	vmci_dev->iobase = iobase;
+	vmci_dev->mmio_base = mmio_base;
 
 	tasklet_init(&vmci_dev->datagram_tasklet,
 		     vmci_dispatch_dgs, (unsigned long)vmci_dev);
 	tasklet_init(&vmci_dev->bm_tasklet,
 		     vmci_process_bitmap, (unsigned long)vmci_dev);
+	init_waitqueue_head(&vmci_dev->inout_wq);
+
+	if (mmio_base != NULL) {
+		vmci_dev->tx_buffer = dma_alloc_coherent(&pdev->dev, VMCI_DMA_DG_BUFFER_SIZE,
+							 &vmci_dev->tx_buffer_base,
+							 GFP_KERNEL);
+		if (!vmci_dev->tx_buffer) {
+			dev_err(&pdev->dev,
+				"Can't allocate memory for datagram tx buffer\n");
+			return -ENOMEM;
+		}
 
-	vmci_dev->data_buffer = vmalloc(VMCI_MAX_DG_SIZE);
+		vmci_dev->data_buffer = dma_alloc_coherent(&pdev->dev, VMCI_DMA_DG_BUFFER_SIZE,
+							   &vmci_dev->data_buffer_base,
+							   GFP_KERNEL);
+	} else {
+		vmci_dev->data_buffer = vmalloc(VMCI_MAX_DG_SIZE);
+	}
 	if (!vmci_dev->data_buffer) {
 		dev_err(&pdev->dev,
 			"Can't allocate memory for datagram buffer\n");
-		return -ENOMEM;
+		error = -ENOMEM;
+		goto err_free_data_buffers;
 	}
 
 	pci_set_master(pdev);	/* To enable queue_pair functionality. */
@@ -490,11 +678,11 @@
 	 *
 	 * Right now, we need datagrams. There are no fallbacks.
 	 */
-	capabilities = ioread32(vmci_dev->iobase + VMCI_CAPS_ADDR);
+	capabilities = vmci_read_reg(vmci_dev, VMCI_CAPS_ADDR);
 	if (!(capabilities & VMCI_CAPS_DATAGRAM)) {
 		dev_err(&pdev->dev, "Device does not support datagrams\n");
 		error = -ENXIO;
-		goto err_free_data_buffer;
+		goto err_free_data_buffers;
 	}
 	caps_in_use = VMCI_CAPS_DATAGRAM;
 
@@ -531,10 +719,32 @@
 		}
 	}
 
+	if (mmio_base != NULL) {
+		if (capabilities & VMCI_CAPS_DMA_DATAGRAM) {
+			caps_in_use |= VMCI_CAPS_DMA_DATAGRAM;
+		} else {
+			dev_err(&pdev->dev,
+				"Missing capability: VMCI_CAPS_DMA_DATAGRAM\n");
+			error = -ENXIO;
+			goto err_free_notification_bitmap;
+		}
+	}
+
 	dev_info(&pdev->dev, "Using capabilities 0x%x\n", caps_in_use);
 
 	/* Let the host know which capabilities we intend to use. */
-	iowrite32(caps_in_use, vmci_dev->iobase + VMCI_CAPS_ADDR);
+	vmci_write_reg(vmci_dev, caps_in_use, VMCI_CAPS_ADDR);
+
+	if (caps_in_use & VMCI_CAPS_DMA_DATAGRAM) {
+		/* Let the device know the size for pages passed down. */
+		vmci_write_reg(vmci_dev, PAGE_SHIFT, VMCI_GUEST_PAGE_SHIFT);
+
+		/* Configure the high order parts of the data in/out buffers. */
+		vmci_write_reg(vmci_dev, upper_32_bits(vmci_dev->data_buffer_base),
+			       VMCI_DATA_IN_HIGH_ADDR);
+		vmci_write_reg(vmci_dev, upper_32_bits(vmci_dev->tx_buffer_base),
+			       VMCI_DATA_OUT_HIGH_ADDR);
+	}
 
 	/* Set up global device so that we can start sending datagrams */
 	spin_lock_irq(&vmci_dev_spinlock);
@@ -561,7 +771,7 @@
 	/* Check host capabilities. */
 	error = vmci_check_host_caps(pdev);
 	if (error)
-		goto err_remove_bitmap;
+		goto err_remove_vmci_dev_g;
 
 	/* Enable device. */
 
@@ -581,13 +791,17 @@
 	 * Enable interrupts.  Try MSI-X first, then MSI, and then fallback on
 	 * legacy interrupts.
 	 */
-	error = pci_alloc_irq_vectors(pdev, VMCI_MAX_INTRS, VMCI_MAX_INTRS,
-			PCI_IRQ_MSIX);
+	if (vmci_dev->mmio_base != NULL)
+		num_irq_vectors = VMCI_MAX_INTRS;
+	else
+		num_irq_vectors = VMCI_MAX_INTRS_NOTIFICATION;
+	error = pci_alloc_irq_vectors(pdev, num_irq_vectors, num_irq_vectors,
+				      PCI_IRQ_MSIX);
 	if (error < 0) {
 		error = pci_alloc_irq_vectors(pdev, 1, 1,
 				PCI_IRQ_MSIX | PCI_IRQ_MSI | PCI_IRQ_LEGACY);
 		if (error < 0)
-			goto err_remove_bitmap;
+			goto err_unsubscribe_event;
 	} else {
 		vmci_dev->exclusive_vectors = true;
 	}
@@ -620,6 +834,17 @@
 				pci_irq_vector(pdev, 1), error);
 			goto err_free_irq;
 		}
+		if (caps_in_use & VMCI_CAPS_DMA_DATAGRAM) {
+			error = request_irq(pci_irq_vector(pdev, 2),
+					    vmci_interrupt_dma_datagram,
+					    0, KBUILD_MODNAME, vmci_dev);
+			if (error) {
+				dev_err(&pdev->dev,
+					"Failed to allocate irq %u: %d\n",
+					pci_irq_vector(pdev, 2), error);
+				goto err_free_bm_irq;
+			}
+		}
 	}
 
 	dev_dbg(&pdev->dev, "Registered device\n");
@@ -630,17 +855,22 @@
 	cmd = VMCI_IMR_DATAGRAM;
 	if (caps_in_use & VMCI_CAPS_NOTIFICATIONS)
 		cmd |= VMCI_IMR_NOTIFICATION;
-	iowrite32(cmd, vmci_dev->iobase + VMCI_IMR_ADDR);
+	if (caps_in_use & VMCI_CAPS_DMA_DATAGRAM)
+		cmd |= VMCI_IMR_DMA_DATAGRAM;
+	vmci_write_reg(vmci_dev, cmd, VMCI_IMR_ADDR);
 
 	/* Enable interrupts. */
-	iowrite32(VMCI_CONTROL_INT_ENABLE,
-		  vmci_dev->iobase + VMCI_CONTROL_ADDR);
+	vmci_write_reg(vmci_dev, VMCI_CONTROL_INT_ENABLE, VMCI_CONTROL_ADDR);
 
 	pci_set_drvdata(pdev, vmci_dev);
 
 	vmci_call_vsock_callback(false);
 	return 0;
 
+err_free_bm_irq:
+	if (vmci_dev->exclusive_vectors)
+		free_irq(pci_irq_vector(pdev, 1), vmci_dev);
+
 err_free_irq:
 	free_irq(pci_irq_vector(pdev, 0), vmci_dev);
 	tasklet_kill(&vmci_dev->datagram_tasklet);
@@ -649,29 +879,29 @@
 err_disable_msi:
 	pci_free_irq_vectors(pdev);
 
+err_unsubscribe_event:
 	vmci_err = vmci_event_unsubscribe(ctx_update_sub_id);
 	if (vmci_err < VMCI_SUCCESS)
 		dev_warn(&pdev->dev,
 			 "Failed to unsubscribe from event (type=%d) with subscriber (ID=0x%x): %d\n",
 			 VMCI_EVENT_CTX_ID_UPDATE, ctx_update_sub_id, vmci_err);
 
-err_remove_bitmap:
-	if (vmci_dev->notification_bitmap) {
-		iowrite32(VMCI_CONTROL_RESET,
-			  vmci_dev->iobase + VMCI_CONTROL_ADDR);
-		dma_free_coherent(&pdev->dev, PAGE_SIZE,
-				  vmci_dev->notification_bitmap,
-				  vmci_dev->notification_base);
-	}
-
 err_remove_vmci_dev_g:
 	spin_lock_irq(&vmci_dev_spinlock);
 	vmci_pdev = NULL;
 	vmci_dev_g = NULL;
 	spin_unlock_irq(&vmci_dev_spinlock);
 
-err_free_data_buffer:
-	vfree(vmci_dev->data_buffer);
+err_free_notification_bitmap:
+	if (vmci_dev->notification_bitmap) {
+		vmci_write_reg(vmci_dev, VMCI_CONTROL_RESET, VMCI_CONTROL_ADDR);
+		dma_free_coherent(&pdev->dev, PAGE_SIZE,
+				  vmci_dev->notification_bitmap,
+				  vmci_dev->notification_base);
+	}
+
+err_free_data_buffers:
+	vmci_free_dg_buffers(vmci_dev);
 
 	/* The rest are managed resources and will be freed by PCI core */
 	return error;
@@ -700,15 +930,18 @@
 	spin_unlock_irq(&vmci_dev_spinlock);
 
 	dev_dbg(&pdev->dev, "Resetting vmci device\n");
-	iowrite32(VMCI_CONTROL_RESET, vmci_dev->iobase + VMCI_CONTROL_ADDR);
+	vmci_write_reg(vmci_dev, VMCI_CONTROL_RESET, VMCI_CONTROL_ADDR);
 
 	/*
 	 * Free IRQ and then disable MSI/MSI-X as appropriate.  For
 	 * MSI-X, we might have multiple vectors, each with their own
 	 * IRQ, which we must free too.
 	 */
-	if (vmci_dev->exclusive_vectors)
+	if (vmci_dev->exclusive_vectors) {
 		free_irq(pci_irq_vector(pdev, 1), vmci_dev);
+		if (vmci_dev->mmio_base != NULL)
+			free_irq(pci_irq_vector(pdev, 2), vmci_dev);
+	}
 	free_irq(pci_irq_vector(pdev, 0), vmci_dev);
 	pci_free_irq_vectors(pdev);
 
@@ -726,7 +959,10 @@
 				  vmci_dev->notification_base);
 	}
 
-	vfree(vmci_dev->data_buffer);
+	vmci_free_dg_buffers(vmci_dev);
+
+	if (vmci_dev->mmio_base != NULL)
+		pci_iounmap(pdev, vmci_dev->mmio_base);
 
 	/* The rest are managed resources and will be freed by PCI core */
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/vmci_host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/vmci_host.c
@@ -165,10 +165,16 @@
 static __poll_t vmci_host_poll(struct file *filp, poll_table *wait)
 {
 	struct vmci_host_dev *vmci_host_dev = filp->private_data;
-	struct vmci_ctx *context = vmci_host_dev->context;
+	struct vmci_ctx *context;
 	__poll_t mask = 0;
 
 	if (vmci_host_dev->ct_type == VMCIOBJ_CONTEXT) {
+		/*
+		 * Read context only if ct_type == VMCIOBJ_CONTEXT to make
+		 * sure that context is initialized
+		 */
+		context = vmci_host_dev->context;
+
 		/* Check for VMCI calls to this VM context. */
 		if (wait)
 			poll_wait(filp, &context->host_context.wait_queue,
@@ -242,6 +248,8 @@
 		context->notify_page = NULL;
 		return VMCI_ERROR_GENERIC;
 	}
+	if (context->notify_page == NULL)
+		return VMCI_ERROR_UNAVAILABLE;
 
 	/*
 	 * Map the locked page and set up notify pointer.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/vmci_queue_pair.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/vmci_queue_pair.c
@@ -854,6 +854,7 @@
 	u32 context_id = vmci_get_context_id();
 	struct vmci_event_qp ev;
 
+	memset(&ev, 0, sizeof(ev));
 	ev.msg.hdr.dst = vmci_make_handle(context_id, VMCI_EVENT_HANDLER);
 	ev.msg.hdr.src = vmci_make_handle(VMCI_HYPERVISOR_CONTEXT_ID,
 					  VMCI_CONTEXT_RESOURCE_ID);
@@ -1467,6 +1468,7 @@
 	 * kernel.
 	 */
 
+	memset(&ev, 0, sizeof(ev));
 	ev.msg.hdr.dst = vmci_make_handle(peer_id, VMCI_EVENT_HANDLER);
 	ev.msg.hdr.src = vmci_make_handle(VMCI_HYPERVISOR_CONTEXT_ID,
 					  VMCI_CONTEXT_RESOURCE_ID);
@@ -2577,6 +2579,12 @@
 	if (result < VMCI_SUCCESS)
 		return result;
 
+	/*
+	 * This virt_wmb() ensures that data written to the queue
+	 * is observable before the new producer_tail is.
+	 */
+	virt_wmb();
+
 	vmci_q_header_add_producer_tail(produce_q->q_header, written,
 					produce_q_size);
 	return written;
@@ -2620,6 +2628,12 @@
 	if (buf_ready < VMCI_SUCCESS)
 		return (ssize_t) buf_ready;
 
+	/*
+	 * This virt_rmb() ensures that data from the queue will be read
+	 * after we have determined how much is ready to be consumed.
+	 */
+	virt_rmb();
+
 	read = (size_t) (buf_ready > buf_size ? buf_size : buf_ready);
 	head = vmci_q_header_consumer_head(produce_q->q_header);
 	if (likely(head + read < consume_q_size)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/vmw_vmci/vmci_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/vmw_vmci/vmci_resource.c
@@ -144,7 +144,8 @@
 	spin_lock(&vmci_resource_table.lock);
 
 	hlist_for_each_entry(r, &vmci_resource_table.entries[idx], node) {
-		if (vmci_handle_is_equal(r->handle, resource->handle)) {
+		if (vmci_handle_is_equal(r->handle, resource->handle) &&
+		    resource->type == r->type) {
 			hlist_del_init_rcu(&r->node);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/Makefile
@@ -0,0 +1,29 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for Xilinx AI engine device driver
+#
+
+obj-$(CONFIG_XILINX_AIE)	+= xilinx-aie.o
+
+xilinx-aie-$(CONFIG_XILINX_AIE) := ai-engine-aie.o		\
+				   ai-engine-aieml.o		\
+				   ai-engine-aperture.o		\
+				   ai-engine-clock.o		\
+				   ai-engine-dev.o		\
+				   ai-engine-dev-v1_0.o		\
+				   ai-engine-dma.o		\
+				   ai-engine-interrupt.o	\
+				   ai-engine-mem.o		\
+				   ai-engine-overlay.o		\
+				   ai-engine-part.o		\
+				   ai-engine-res.o		\
+				   ai-engine-reset.o		\
+				   ai-engine-rscmgr.o		\
+				   ai-engine-sysfs.o		\
+				   ai-engine-sysfs-clock.o	\
+				   ai-engine-sysfs-core.o	\
+				   ai-engine-sysfs-dma.o	\
+				   ai-engine-sysfs-error.o	\
+				   ai-engine-sysfs-event.o	\
+				   ai-engine-sysfs-lock.o	\
+				   ai-engine-sysfs-status.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-aie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-aie.c
@@ -0,0 +1,1384 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine driver AIE device specific implementation
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+#define AIE_ARRAY_SHIFT		30U
+#define AIE_COL_SHIFT		23U
+#define AIE_ROW_SHIFT		18U
+
+#define NUM_MEMS_PER_TILE	2U
+
+#define NUM_MODS_CORE_TILE	2U
+#define NUM_MODS_SHIMPL_TILE	1U
+
+/*
+ * Number of resources per module
+ */
+#define AIE_NUM_PERF_CORE_MOD		4U
+#define AIE_NUM_USEREVENT_CORE_MOD	4U
+#define AIE_NUM_TRACECONTROL_CORE_MOD	1U
+#define AIE_NUM_PCEVENT_CORE_MOD	4U
+#define AIE_NUM_SSSELECT_CORE_MOD	8U
+#define AIE_NUM_BROADCAST_CORE_MOD	16U
+#define AIE_NUM_COMBOEVENT_CORE_MOD	4U
+#define AIE_NUM_GROUPEVENTS_CORE_MOD	9U
+
+#define AIE_NUM_PERF_MEM_MOD		2U
+#define AIE_NUM_USEREVENT_MEM_MOD	4U
+#define AIE_NUM_TRACECONTROL_MEM_MOD	1U
+#define AIE_NUM_PCEVENT_MEM_MOD		0U
+#define AIE_NUM_SSSELECT_MEM_MOD	0U
+#define AIE_NUM_BROADCAST_MEM_MOD	16U
+#define AIE_NUM_COMBOEVENT_MEM_MOD	4U
+#define AIE_NUM_GROUPEVENTS_MEM_MOD	8U
+
+#define AIE_NUM_PERF_PL_MOD		2U
+#define AIE_NUM_USEREVENT_PL_MOD	4U
+#define AIE_NUM_TRACECONTROL_PL_MOD	1U
+#define AIE_NUM_PCEVENT_PL_MOD		0U
+#define AIE_NUM_SSSELECT_PL_MOD		8U
+#define AIE_NUM_BROADCAST_PL_MOD	16U
+#define AIE_NUM_COMBOEVENT_PL_MOD	4U
+#define AIE_NUM_GROUPEVENTS_PL_MOD	7U
+
+/*
+ * Registers offsets
+ */
+#define AIE_SHIMNOC_L2INTR_MASK_REGOFF		0x00015000U
+#define AIE_SHIMNOC_L2INTR_INTR_REGOFF		0x00015010U
+#define AIE_SHIMNOC_DMA_BD0_ADDRLOW_REGOFF	0x0001d000U
+#define AIE_SHIMNOC_DMA_BD15_PACKET_REGOFF	0x0001d13cU
+#define AIE_SHIMNOC_AXIMM_REGOFF		0x0001e020U
+#define AIE_SHIMPL_BISR_CACHE_CTRL_REGOFF	0x00036000U
+#define AIE_SHIMPL_L1INTR_MASK_A_REGOFF		0x00035000U
+#define AIE_SHIMPL_L1INTR_BLOCK_NORTH_B_REGOFF	0x00035050U
+#define AIE_SHIMPL_CLKCNTR_REGOFF		0x00036040U
+#define AIE_SHIMPL_COLRESET_REGOFF		0x00036048U
+#define AIE_SHIMPL_RESET_REGOFF			0x0003604cU
+#define AIE_SHIMPL_GROUP_ERROR_REGOFF		0x0003450cU
+#define AIE_TILE_CORE_CLKCNTR_REGOFF		0x00036040U
+#define AIE_TILE_CORE_GROUP_ERROR_REGOFF	0x00034510U
+#define AIE_TILE_MEM_GROUP_ERROR_REGOFF		0x00014514U
+#define AIE_TILE_CORE_R0_REGOFF			0x00030000U
+#define AIE_TILE_CORE_LC_REGOFF			0x00030520U
+#define AIE_TILE_CORE_VRL0_REGOFF		0x00030530U
+#define AIE_TILE_CORE_AMH3_PART3_REGOFF		0x000307a0U
+
+/*
+ * Register masks
+ */
+#define AIE_SHIMPL_SHIMRST_MASK			0x1U
+#define AIE_SHIMPL_COLRST_MASK			0x1U
+#define AIE_SHIMPL_CLKCNTR_COLBUF_MASK		0x1U
+#define AIE_SHIMPL_CLKCNTR_NEXTCLK_MASK		BIT(1)
+#define AIE_TILE_CLKCNTR_COLBUF_MASK		BIT(0)
+#define AIE_TILE_CLKCNTR_NEXTCLK_MASK		BIT(1)
+
+/*
+ * AI engine SHIM reset ID.
+ * TODO: it should follow the Linux reset framework. The ID should be in the
+ * device tree. However, as versal resets is not ready, we hardcode it in the
+ * driver.
+ */
+#define VERSAL_PM_RST_AIE_SHIM_ID			0xc10405fU
+
+/* Macros to define size of a sysfs binary attribute */
+#define AIE_PART_SYSFS_CORE_BINA_SIZE		0x4000		/* 16KB */
+#define AIE_PART_SYSFS_DMA_BINA_SIZE		0xC800		/* 50KB */
+#define AIE_PART_SYSFS_LOCK_BINA_SIZE		0x28000		/* 160KB */
+#define AIE_PART_SYSFS_ERROR_BINA_SIZE		0x4000		/* 16KB */
+#define AIE_PART_SYSFS_STATUS_BINA_SIZE		0x3c000		/* 240KB */
+
+static const struct aie_tile_regs aie_kernel_regs[] = {
+	/* SHIM AXI MM Config */
+	{.attribute = AIE_TILE_TYPE_MASK_SHIMNOC << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMNOC_AXIMM_REGOFF,
+	 .eoff = AIE_SHIMNOC_AXIMM_REGOFF,
+	},
+	/* SHIM DMA ADDRESS range */
+	{.attribute = AIE_TILE_TYPE_MASK_SHIMNOC << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMNOC_DMA_BD0_ADDRLOW_REGOFF,
+	 .eoff = AIE_SHIMNOC_DMA_BD15_PACKET_REGOFF,
+	},
+	/* SHIM 2nd level interrupt controller */
+	{.attribute = AIE_TILE_TYPE_MASK_SHIMNOC << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMNOC_L2INTR_MASK_REGOFF,
+	 .eoff = AIE_SHIMNOC_L2INTR_INTR_REGOFF,
+	},
+	/* SHIM 1st level interrupt controller */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMPL_L1INTR_MASK_A_REGOFF,
+	 .eoff = AIE_SHIMPL_L1INTR_BLOCK_NORTH_B_REGOFF,
+	},
+	/* SHIM column reset */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMPL_COLRESET_REGOFF,
+	 .eoff = AIE_SHIMPL_COLRESET_REGOFF,
+	},
+	/* SHIM reset Enable */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMPL_RESET_REGOFF,
+	 .eoff = AIE_SHIMPL_RESET_REGOFF,
+	},
+	/* SHIM clock control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMPL_CLKCNTR_REGOFF,
+	 .eoff = AIE_SHIMPL_CLKCNTR_REGOFF,
+	},
+	/* SHIM BISR cache control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMPL_BISR_CACHE_CTRL_REGOFF,
+	 .eoff = AIE_SHIMPL_BISR_CACHE_CTRL_REGOFF,
+	},
+	/* SHIM group error enable */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_SHIMPL_GROUP_ERROR_REGOFF,
+	 .eoff = AIE_SHIMPL_GROUP_ERROR_REGOFF,
+	},
+	/* Tile clock control */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_TILE_CORE_CLKCNTR_REGOFF,
+	 .eoff = AIE_TILE_CORE_CLKCNTR_REGOFF,
+	},
+	/* Tile group error for core module */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_TILE_CORE_GROUP_ERROR_REGOFF,
+	 .eoff = AIE_TILE_CORE_GROUP_ERROR_REGOFF,
+	},
+	/* Tile group error for memory module */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIE_TILE_MEM_GROUP_ERROR_REGOFF,
+	 .eoff = AIE_TILE_MEM_GROUP_ERROR_REGOFF,
+	},
+};
+
+static const struct aie_tile_regs aie_core_32bit_regs = {
+	.attribute = AIE_TILE_TYPE_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	.soff = AIE_TILE_CORE_R0_REGOFF,
+	.eoff = AIE_TILE_CORE_LC_REGOFF,
+};
+
+static const struct aie_tile_regs aie_core_128bit_regs = {
+	.attribute = AIE_TILE_TYPE_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	.soff = AIE_TILE_CORE_VRL0_REGOFF,
+	.eoff = AIE_TILE_CORE_AMH3_PART3_REGOFF,
+};
+
+static const struct aie_core_regs_attr aie_core_regs[] = {
+	{.core_regs = &aie_core_32bit_regs,
+	 .width = 1,
+	},
+	{.core_regs = &aie_core_128bit_regs,
+	 .width = 4,
+	},
+};
+
+static const struct aie_single_reg_field aie_col_rst = {
+	.mask = AIE_SHIMPL_COLRST_MASK,
+	.regoff = AIE_SHIMPL_COLRESET_REGOFF,
+};
+
+static const struct aie_single_reg_field aie_col_clkbuf = {
+	.mask = AIE_SHIMPL_CLKCNTR_COLBUF_MASK,
+	.regoff = AIE_SHIMPL_CLKCNTR_REGOFF,
+};
+
+static const struct aie_dma_attr aie_shimdma = {
+	.laddr = {
+		.mask = 0xffffffffU,
+		.regoff = 0U,
+	},
+	.haddr = {
+		.mask = 0xffff0000U,
+		.regoff = 0x8U,
+	},
+	.buflen = {
+		.mask = 0xffffffffU,
+		.regoff = 0x4U,
+	},
+	.sts = {
+		.mask = GENMASK(1, 0),
+		.regoff = 2U,
+	},
+	.stall = {
+		.mask = BIT(4),
+		.regoff = 1U,
+	},
+	.qsize = {
+		.mask = GENMASK(8, 6),
+		.regoff = 3U,
+	},
+	.curbd = {
+		.mask = GENMASK(19, 16),
+		.regoff = 4U,
+	},
+	.qsts = {
+		.mask = BIT(28),
+		.regoff = 1U,
+	},
+	.fifo_cnt = {
+		.mask = GENMASK(12, 0),
+		.regoff = 16U,
+	},
+	.bd_regoff = AIE_SHIMNOC_DMA_BD0_ADDRLOW_REGOFF,
+	.mm2s_sts_regoff = 0x1d164U,
+	.s2mm_sts_regoff = 0x1d160U,
+	.fifo_cnt_regoff = 0x1DF20U,
+	.num_bds = 16,
+	.num_mm2s_chan = 2U,
+	.num_s2mm_chan = 2U,
+	.bd_len = 0x14U,
+};
+
+static const struct aie_dma_attr aie_tiledma = {
+	.sts = {
+		.mask = GENMASK(1, 0),
+		.regoff = 2U,
+	},
+	.stall = {
+		.mask = BIT(4),
+		.regoff = 1U,
+	},
+	.qsize = {
+		.mask = GENMASK(8, 6),
+		.regoff = 3U,
+	},
+	.curbd = {
+		.mask = GENMASK(19, 16),
+		.regoff = 4U,
+	},
+	.qsts = {
+		.mask = BIT(28),
+		.regoff = 1U,
+	},
+	.mm2s_sts_regoff = 0x1df10U,
+	.s2mm_sts_regoff = 0x1df00U,
+	.num_bds = 16,
+	.num_mm2s_chan = 2U,
+	.num_s2mm_chan = 2U,
+};
+
+static char *aie_dma_status_str[] = {
+	"idle",
+	"starting",
+	"running",
+	"stalled_on_requesting_lock",
+};
+
+static char *aie_queue_status_str[] = {
+	"okay",
+	"overflow",
+};
+
+static const struct aie_event_attr aie_pl_event = {
+	.bc_event = {
+		.mask = GENMASK(6, 0),
+		.regoff = 0x0U,
+	},
+	.group_error = {
+		.mask = GENMASK(10, 0),
+		.regoff = 0xcU,
+	},
+	.bc_regoff = 0x34010U,
+	.status_regoff = 0x34200U,
+	.group_regoff = 0x34500U,
+	.base_error_event = 62U,
+	.num_broadcasts = 16U,
+	.base_bc_event = 107U,
+	.num_events = 128U,
+};
+
+static const struct aie_event_attr aie_mem_event = {
+	.bc_event = {
+		.mask = GENMASK(6, 0),
+		.regoff = 0x0U,
+	},
+	.group_error = {
+		.mask = GENMASK(13, 0),
+		.regoff = 0x14U,
+	},
+	.bc_regoff = 0x14010U,
+	.status_regoff = 0x14200U,
+	.group_regoff = 0x14500U,
+	.base_error_event = 87U,
+	.num_broadcasts = 16U,
+	.base_bc_event = 107U,
+	.num_events = 128U,
+};
+
+static const struct aie_event_attr aie_core_event = {
+	.bc_event = {
+		.mask = GENMASK(6, 0),
+		.regoff = 0x0U,
+	},
+	.group_error = {
+		.mask = GENMASK(21, 0),
+		.regoff = 0x10U,
+	},
+	.bc_regoff = 0x34010U,
+	.status_regoff = 0x34200U,
+	.group_regoff = 0x34500U,
+	.base_error_event = 48U,
+	.num_broadcasts = 16U,
+	.base_bc_event = 107U,
+	.num_events = 128U,
+};
+
+static const struct aie_l1_intr_ctrl_attr aie_l1_intr_ctrl = {
+	.swa_status = {
+		.mask = GENMASK(19, 0),
+		.regoff = 0xcU,
+	},
+	.swb_status = {
+		.mask = GENMASK(19, 0),
+		.regoff = 0x3cU,
+	},
+	.swa_event = {
+		.mask = GENMASK(6, 0),
+		.regoff = 0x14U,
+	},
+	.swb_event = {
+		.mask = GENMASK(6, 0),
+		.regoff = 0x44U,
+	},
+	.regoff = 0x35000U,
+	.event_lsb = 8,
+	.num_broadcasts = 0x14U,
+};
+
+static const struct aie_l2_intr_ctrl_attr aie_l2_intr_ctrl = {
+	.mask = {
+		.mask = GENMASK(15, 0),
+		.regoff = 0x0U,
+	},
+	.enable = {
+		.mask = GENMASK(15, 0),
+		.regoff = 0x4U,
+	},
+	.disable = {
+		.mask = GENMASK(15, 0),
+		.regoff = 0x8U,
+	},
+	.status = {
+		.mask = GENMASK(15, 0),
+		.regoff = 0xcU,
+	},
+	.regoff = 0x15000U,
+	.num_broadcasts = 0x10U,
+};
+
+static const struct aie_event_prop aie_core_stream_error_prop[] = {
+	{
+		.event = 54U,
+		.event_str = "tlast_in_wss_words_0-2",
+	},
+	{
+		.event = 57U,
+		.event_str = "control_packet_error",
+	},
+	{
+		.event = 56U,
+		.event_str = "stream_packet_parity_error",
+	},
+};
+
+static const struct aie_event_prop aie_core_inst_error_prop[] = {
+	{
+		.event = 59U,
+		.event_str = "instruction_decompression_error",
+	},
+};
+
+static const struct aie_event_prop aie_core_ecc_error_prop[] = {
+	{
+		.event = 64U,
+		.event_str = "pm_ecc_error_2-bit",
+	},
+	{
+		.event = 62U,
+		.event_str = "pm_ecc_error_scrub_2-bit",
+	},
+};
+
+static const struct aie_event_prop aie_core_access_error_prop[] = {
+	{
+		.event = 55U,
+		.event_str = "pm_reg_access_failure",
+	},
+	{
+		.event = 66U,
+		.event_str = "dm_access_to_unavailable",
+	},
+	{
+		.event = 65U,
+		.event_str = "pm_address_out_of_range",
+	},
+	{
+		.event = 60U,
+		.event_str = "dm_address_out_of_range",
+	},
+};
+
+static const struct aie_event_prop aie_core_lock_error_prop[] = {
+	{
+		.event = 67U,
+		.event_str = "lock_access_to_unavailable",
+	},
+};
+
+static const struct aie_event_prop aie_core_bus_error_prop[] = {
+	{
+		.event = 58U,
+		.event_str = "axi-mm_slave_error",
+	},
+};
+
+static const struct aie_event_prop aie_mem_ecc_error_prop[] = {
+	{
+		.event = 88U,
+		.event_str = "dm_ecc_error_scrub_2-bit",
+	},
+	{
+		.event = 90U,
+		.event_str = "dm_ecc_error_2-bit",
+	},
+};
+
+static const struct aie_event_prop aie_mem_parity_error_prop[] = {
+	{
+		.event = 91U,
+		.event_str = "dm_parity_error_bank_2",
+	},
+	{
+		.event = 92U,
+		.event_str = "dm_parity_error_bank_3",
+	},
+	{
+		.event = 93U,
+		.event_str = "dm_parity_error_bank_4",
+	},
+	{
+		.event = 94U,
+		.event_str = "dm_parity_error_bank_5",
+	},
+	{
+		.event = 95U,
+		.event_str = "dm_parity_error_bank_6",
+	},
+	{
+		.event = 96U,
+		.event_str = "dm_parity_error_bank_7",
+	},
+};
+
+static const struct aie_event_prop aie_mem_dma_error_prop[] = {
+	{
+		.event = 97U,
+		.event_str = "dma_s2mm_0_error",
+	},
+	{
+		.event = 98U,
+		.event_str = "dma_s2mm_1_error",
+	},
+	{
+		.event = 99U,
+		.event_str = "dma_mm2s_0_error",
+	},
+	{
+		.event = 100U,
+		.event_str = "dma_mm2s_1_error",
+	},
+};
+
+static const struct aie_event_prop aie_shim_bus_error_prop[] = {
+	{
+		.event = 62U,
+		.event_str = "axi-mm_slave_tile_error",
+	},
+};
+
+static const struct aie_event_prop aie_shim_stream_error_prop[] = {
+	{
+		.event = 63U,
+		.event_str = "control_packet_error",
+	},
+	{
+		.event = 64U,
+		.event_str = "axi-mm_decode_nsu_error",
+	},
+	{
+		.event = 65U,
+		.event_str = "axi-mm_slave_nsu_error",
+	},
+	{
+		.event = 66U,
+		.event_str = "axi-mm_unsupported_traffic",
+	},
+	{
+		.event = 67U,
+		.event_str = "axi-mm_unsecure_access_in_secure_mode",
+	},
+	{
+		.event = 68U,
+		.event_str = "axi-mm_byte_strobe_error",
+	},
+};
+
+static const struct aie_event_prop aie_shim_dma_error_prop[] = {
+	{
+		.event = 69U,
+		.event_str = "dma_s2mm_0_error",
+	},
+	{
+		.event = 70U,
+		.event_str = "dma_s2mm_1_error",
+	},
+	{
+		.event = 71U,
+		.event_str = "dma_mm2s_0_error",
+	},
+	{
+		.event = 72U,
+		.event_str = "dma_mm2s_1_error",
+	},
+};
+
+static const struct aie_err_category aie_core_err_category[] = {
+	{
+		/* AIE_ERROR_CATEGORY_STREAM */
+		.err_category = AIE_ERROR_CATEGORY_STREAM,
+		.num_events = ARRAY_SIZE(aie_core_stream_error_prop),
+		.prop = aie_core_stream_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_ACCESS */
+		.err_category = AIE_ERROR_CATEGORY_ACCESS,
+		.num_events = ARRAY_SIZE(aie_core_access_error_prop),
+		.prop = aie_core_access_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_BUS */
+		.err_category = AIE_ERROR_CATEGORY_BUS,
+		.num_events = ARRAY_SIZE(aie_core_bus_error_prop),
+		.prop = aie_core_bus_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_INSTRUCTION */
+		.err_category = AIE_ERROR_CATEGORY_INSTRUCTION,
+		.num_events = ARRAY_SIZE(aie_core_inst_error_prop),
+		.prop = aie_core_inst_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_ECC */
+		.err_category = AIE_ERROR_CATEGORY_ECC,
+		.num_events = ARRAY_SIZE(aie_core_ecc_error_prop),
+		.prop = aie_core_ecc_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_LOCK */
+		.err_category = AIE_ERROR_CATEGORY_LOCK,
+		.num_events = ARRAY_SIZE(aie_core_lock_error_prop),
+		.prop = aie_core_lock_error_prop,
+	},
+};
+
+static const struct aie_err_category aie_mem_err_category[] = {
+	{
+		/* AIE_ERROR_CATEGORY_ECC */
+		.err_category = AIE_ERROR_CATEGORY_ECC,
+		.num_events = ARRAY_SIZE(aie_mem_ecc_error_prop),
+		.prop = aie_mem_ecc_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_MEM_PARITY */
+		.err_category = AIE_ERROR_CATEGORY_MEM_PARITY,
+		.num_events = ARRAY_SIZE(aie_mem_parity_error_prop),
+		.prop = aie_mem_parity_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_DMA */
+		.err_category = AIE_ERROR_CATEGORY_DMA,
+		.num_events = ARRAY_SIZE(aie_mem_dma_error_prop),
+		.prop = aie_mem_dma_error_prop,
+	},
+};
+
+static const struct aie_err_category aie_shim_err_category[] = {
+	{
+		/* AIE_ERROR_CATEGORY_BUS */
+		.err_category = AIE_ERROR_CATEGORY_BUS,
+		.num_events = ARRAY_SIZE(aie_shim_bus_error_prop),
+		.prop = aie_shim_bus_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_STREAM */
+		.err_category = AIE_ERROR_CATEGORY_STREAM,
+		.num_events = ARRAY_SIZE(aie_shim_stream_error_prop),
+		.prop = aie_shim_stream_error_prop,
+	},
+	{
+		/* AIE_ERROR_CATEGORY_DMA */
+		.err_category = AIE_ERROR_CATEGORY_DMA,
+		.num_events = ARRAY_SIZE(aie_shim_dma_error_prop),
+		.prop = aie_shim_dma_error_prop,
+	},
+};
+
+static const struct aie_error_attr aie_core_error = {
+	.num_err_categories = ARRAY_SIZE(aie_core_err_category),
+	.err_category = aie_core_err_category,
+};
+
+static const struct aie_error_attr aie_mem_error = {
+	.num_err_categories = ARRAY_SIZE(aie_mem_err_category),
+	.err_category = aie_mem_err_category,
+};
+
+static const struct aie_error_attr aie_shim_error = {
+	.num_err_categories = ARRAY_SIZE(aie_shim_err_category),
+	.err_category = aie_shim_err_category,
+};
+
+/* resource attributes for core tile type */
+static const
+struct aie_tile_rsc_attr aie_core_tile_rscs_attr[AIE_RSCTYPE_MAX] =  {
+	{
+		/* perf counter */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_PERF_MEM_MOD,},
+			{.num_rscs = AIE_NUM_PERF_CORE_MOD,},
+		},
+	},
+	{
+		/* user event */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_USEREVENT_MEM_MOD,},
+			{.num_rscs = AIE_NUM_USEREVENT_CORE_MOD,},
+		},
+	},
+	{
+		/* trace control */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_TRACECONTROL_MEM_MOD,},
+			{.num_rscs = AIE_NUM_TRACECONTROL_CORE_MOD,},
+		},
+	},
+	{
+		/* pc event */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_PCEVENT_MEM_MOD,},
+			{.num_rscs = AIE_NUM_PCEVENT_CORE_MOD,},
+		},
+	},
+	{
+		/* stream switch port select */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_SSSELECT_MEM_MOD,},
+			{.num_rscs = AIE_NUM_SSSELECT_CORE_MOD,},
+		},
+	},
+	{
+		/* broadcast */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_BROADCAST_MEM_MOD,},
+			{.num_rscs = AIE_NUM_BROADCAST_CORE_MOD,},
+		},
+	},
+	{
+		/* combo events */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_COMBOEVENT_MEM_MOD,},
+			{.num_rscs = AIE_NUM_COMBOEVENT_CORE_MOD,},
+		},
+	},
+	{
+		/* group events */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_GROUPEVENTS_MEM_MOD,},
+			{.num_rscs = AIE_NUM_GROUPEVENTS_CORE_MOD,},
+		},
+	},
+};
+
+/* resource attributes for SHIM PL tile type */
+static const
+struct aie_tile_rsc_attr aie_shimpl_tile_rscs_attr[AIE_RSCTYPE_MAX] =  {
+	{
+		/* perf counter */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_PERF_PL_MOD,},
+		},
+	},
+	{
+		/* user event */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_USEREVENT_PL_MOD,},
+		},
+	},
+	{
+		/* trace control */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_TRACECONTROL_PL_MOD},
+		},
+	},
+	{
+		/* pc event */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_PCEVENT_PL_MOD},
+		},
+	},
+	{
+		/* stream switch port select */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_SSSELECT_PL_MOD},
+		},
+	},
+	{
+		/* broadcast */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_BROADCAST_PL_MOD},
+		},
+	},
+	{
+		/* combo events */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_COMBOEVENT_PL_MOD},
+		},
+	},
+	{
+		/* group events */
+		.mod_attr = {
+			{.num_rscs = AIE_NUM_GROUPEVENTS_PL_MOD},
+		},
+	},
+};
+
+/* modules types array of CORE tile */
+static const
+enum aie_module_type aie_core_tile_module_types[NUM_MODS_CORE_TILE] = {
+	AIE_MEM_MOD,
+	AIE_CORE_MOD,
+};
+
+/* modules types array of SHIM PL tile */
+static const
+enum aie_module_type aie_shimpl_tile_module_types[NUM_MODS_SHIMPL_TILE] = {
+	AIE_PL_MOD,
+};
+
+static const struct aie_single_reg_field aie_core_sts = {
+	.mask = GENMASK(20, 0),
+	.regoff = 0x32004U,
+};
+
+static const struct aie_single_reg_field aie_core_done = {
+	.mask = BIT(20),
+	.regoff = 0x32004U,
+};
+
+static const struct aie_single_reg_field aie_core_disable_event_sts = {
+	.mask = BIT(15),
+	.regoff = 0x32008U,
+};
+
+static const struct aie_single_reg_field aie_core_pc = {
+	.mask = GENMASK(19, 0),
+	.regoff = 0x30280U,
+};
+
+static const struct aie_single_reg_field aie_core_lr = {
+	.mask = GENMASK(19, 0),
+	.regoff = 0x302B0U,
+};
+
+static const struct aie_single_reg_field aie_core_sp = {
+	.mask = GENMASK(19, 0),
+	.regoff = 0x302A0U,
+};
+
+static char *aie_core_status_str[] = {
+	"enabled",
+	"reset",
+	"south_memory_stall",
+	"west_memory_stall",
+	"north_memory_stall",
+	"east_memory_stall",
+	"south_lock_stall",
+	"west_lock_stall",
+	"north_lock_stall",
+	"east_lock_stall",
+	"stream_stall_ss0",
+	"stream_stall_ss1",
+	"stream_stall_ms0",
+	"stream_stall_ms1",
+	"cascade_stall_scd",
+	"cascade_stall_mcd",
+	"debug_halt",
+	"ecc_error_stall",
+	"ecc_scrubbing_stall",
+	"error_halt",
+	"core_done",
+};
+
+static const struct aie_lock_attr aie_pl_lock = {
+	.sts = {
+		.mask = GENMASK(1, 0),
+		.regoff = 2U,
+	},
+	.sts_regoff = 0x14F00,
+	.num_locks = 16U,
+};
+
+static const struct aie_lock_attr aie_mem_lock = {
+	.sts = {
+		.mask = GENMASK(1, 0),
+		.regoff = 2U,
+	},
+	.sts_regoff = 0x1EF00,
+	.num_locks = 16U,
+};
+
+static char *aie_lock_status_str[] = {
+	"released_for_write",
+	"acquired_for_write",
+	"released_for_read",
+	"acquired_for_read",
+};
+
+static const struct aie_dev_attr aie_tile_dev_attr[] = {
+	AIE_TILE_DEV_ATTR_RO(core, AIE_TILE_TYPE_MASK_TILE),
+	AIE_TILE_DEV_ATTR_RO(dma, AIE_TILE_TYPE_MASK_TILE |
+			     AIE_TILE_TYPE_MASK_SHIMNOC),
+	AIE_TILE_DEV_ATTR_RO(error, AIE_TILE_TYPE_MASK_TILE |
+			     AIE_TILE_TYPE_MASK_SHIMNOC |
+			     AIE_TILE_TYPE_MASK_SHIMPL),
+	AIE_TILE_DEV_ATTR_RO(event, AIE_TILE_TYPE_MASK_TILE |
+			     AIE_TILE_TYPE_MASK_SHIMNOC |
+			     AIE_TILE_TYPE_MASK_SHIMPL),
+	AIE_TILE_DEV_ATTR_RO(lock, AIE_TILE_TYPE_MASK_TILE |
+			     AIE_TILE_TYPE_MASK_SHIMNOC),
+};
+
+static const struct aie_dev_attr aie_part_dev_attr[] = {
+	AIE_PART_DEV_ATTR_RO(error_stat),
+	AIE_PART_DEV_ATTR_RO(current_freq),
+};
+
+static const struct aie_bin_attr aie_part_bin_attr[] = {
+	AIE_PART_BIN_ATTR_RO(core, AIE_PART_SYSFS_CORE_BINA_SIZE),
+	AIE_PART_BIN_ATTR_RO(dma, AIE_PART_SYSFS_DMA_BINA_SIZE),
+	AIE_PART_BIN_ATTR_RO(error, AIE_PART_SYSFS_ERROR_BINA_SIZE),
+	AIE_PART_BIN_ATTR_RO(lock, AIE_PART_SYSFS_LOCK_BINA_SIZE),
+	AIE_PART_BIN_ATTR_RO(status, AIE_PART_SYSFS_STATUS_BINA_SIZE),
+};
+
+static const struct aie_sysfs_attr aie_part_sysfs_attr = {
+	.dev_attr = aie_part_dev_attr,
+	.bin_attr = aie_part_bin_attr,
+	.num_dev_attrs = ARRAY_SIZE(aie_part_dev_attr),
+	.num_bin_attrs = ARRAY_SIZE(aie_part_bin_attr),
+};
+
+static const struct aie_sysfs_attr aie_tile_sysfs_attr = {
+	.dev_attr = aie_tile_dev_attr,
+	.bin_attr = NULL,
+	.num_dev_attrs = ARRAY_SIZE(aie_tile_dev_attr),
+	.num_bin_attrs = 0U,
+};
+
+static u32 aie_get_tile_type(struct aie_device *adev, struct aie_location *loc)
+{
+	if (loc->row)
+		return AIE_TILE_TYPE_TILE;
+	/* SHIM row */
+	if ((loc->col % 4) < 2)
+		return AIE_TILE_TYPE_SHIMPL;
+
+	return AIE_TILE_TYPE_SHIMNOC;
+}
+
+static unsigned int aie_get_mem_info(struct aie_device *adev,
+				     struct aie_range *range,
+				     struct aie_part_mem *pmem)
+{
+	unsigned int i;
+	u8 start_row, num_rows;
+
+	if (range->start.row + range->size.row <= 1) {
+		/* SHIM row only, no memories in this range */
+		return 0;
+	}
+	if (!pmem)
+		return NUM_MEMS_PER_TILE;
+
+	for (i = 0; i < NUM_MEMS_PER_TILE; i++) {
+		struct aie_mem *mem = &pmem[i].mem;
+
+		memcpy(&mem->range, range, sizeof(*range));
+	}
+
+	start_row = adev->ttype_attr[AIE_TILE_TYPE_TILE].start_row;
+	num_rows = adev->ttype_attr[AIE_TILE_TYPE_TILE].num_rows;
+	/* Setup tile data memory information */
+	pmem[0].mem.offset = 0;
+	pmem[0].mem.size = KBYTES(32);
+	pmem[0].mem.range.start.row = start_row;
+	pmem[0].mem.range.size.row = num_rows;
+	/* Setup program memory information */
+	pmem[1].mem.offset = 0x20000;
+	pmem[1].mem.size = KBYTES(16);
+	pmem[1].mem.range.start.row = start_row;
+	pmem[1].mem.range.size.row = num_rows;
+
+	return NUM_MEMS_PER_TILE;
+}
+
+/**
+ * aie_set_shim_reset() - Set AI engine SHIM reset
+ * @aperture: AI engine aperture
+ * @range: range of AI engine tiles
+ * @assert: true to set reset, false to unset reset
+ */
+static void aie_set_shim_reset(struct aie_aperture *aperture,
+			       struct aie_range *range, bool assert)
+{
+	u32 c;
+	u32 val;
+	struct aie_location loc;
+
+	val = FIELD_PREP(AIE_SHIMPL_SHIMRST_MASK, (assert ? 1 : 0));
+	loc.row = 0;
+	for (c = range->start.col; c < range->start.col + range->size.col;
+	     c++) {
+		u32 regoff;
+
+		loc.col = c;
+		regoff = aie_cal_regoff(aperture->adev, loc,
+					AIE_SHIMPL_RESET_REGOFF);
+		iowrite32(val, aperture->base + regoff);
+	}
+}
+
+static int aie_reset_shim(struct aie_aperture *aperture,
+			  struct aie_range *range)
+{
+	int ret;
+
+	/* Enable shim reset of each column */
+	aie_set_shim_reset(aperture, range, true);
+
+	/* Assert shim reset of AI engine array */
+	ret = zynqmp_pm_reset_assert(VERSAL_PM_RST_AIE_SHIM_ID,
+				     PM_RESET_ACTION_ASSERT);
+	if (ret < 0) {
+		dev_err(&aperture->dev, "failed to assert SHIM reset.\n");
+		return ret;
+	}
+
+	/* Release shim reset of AI engine array */
+	ret = zynqmp_pm_reset_assert(VERSAL_PM_RST_AIE_SHIM_ID,
+				     PM_RESET_ACTION_RELEASE);
+	if (ret < 0) {
+		dev_err(&aperture->dev, "failed to release SHIM reset.\n");
+		return ret;
+	}
+
+	/* Disable shim reset of each column */
+	aie_set_shim_reset(aperture, range, false);
+
+	return 0;
+}
+
+static int aie_init_part_clk_state(struct aie_partition *apart)
+{
+	int ret, num_tiles;
+
+	num_tiles = apart->range.size.col * (apart->range.size.row - 1);
+
+	ret = aie_resource_initialize(&apart->cores_clk_state, num_tiles);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to initialize cores clock state resource.\n");
+		return ret;
+	}
+
+	ret = aie_resource_initialize(&apart->tiles_inuse, num_tiles);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to initialize tiles in use resource.\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int aie_scan_part_clocks(struct aie_partition *apart)
+{
+	struct aie_device *adev = apart->adev;
+	struct aie_aperture *aperture = apart->aperture;
+	struct aie_range *range = &apart->range;
+	struct aie_location loc;
+
+	/* Clear the bitmap of cores and memories clock state */
+	aie_resource_put_region(&apart->cores_clk_state, 0,
+				apart->cores_clk_state.total);
+
+	for (loc.col = range->start.col;
+	     loc.col < range->start.col + range->size.col;
+	     loc.col++) {
+		for (loc.row = range->start.row;
+		     loc.row < range->start.row + range->size.row - 1;
+		     loc.row++) {
+			void __iomem *va;
+			u32 val, nbitpos;
+
+			/*
+			 * Reading registers of the current tile to see the next
+			 * tile is clock gated.
+			 */
+			nbitpos = loc.col * (range->size.row - 1) + loc.row;
+
+			if (aie_get_tile_type(adev, &loc) !=
+					AIE_TILE_TYPE_TILE) {
+				/* Checks shim tile for next core tile */
+				va = aperture->base +
+				     aie_cal_regoff(adev, loc,
+						    AIE_SHIMPL_CLKCNTR_REGOFF);
+				val = ioread32(va);
+
+				/*
+				 * check if the clock buffer and the next clock
+				 * tile is set, if one of them is not set, the
+				 * tiles of the column are clock gated.
+				 */
+				if (!(val & AIE_SHIMPL_CLKCNTR_COLBUF_MASK) ||
+				    !(val & AIE_SHIMPL_CLKCNTR_NEXTCLK_MASK))
+					break;
+
+				/* Set next tile in the row clock state on */
+				aie_resource_set(&apart->cores_clk_state,
+						 nbitpos, 1);
+				continue;
+			}
+
+			/* Checks core tile for next tile */
+			va = aperture->base +
+			     aie_cal_regoff(adev, loc,
+					    AIE_TILE_CORE_CLKCNTR_REGOFF);
+			val = ioread32(va);
+
+			/*
+			 * If the next tile is gated, skip the rest of the
+			 * column.
+			 */
+			if (!(val & AIE_TILE_CLKCNTR_NEXTCLK_MASK))
+				break;
+
+			aie_resource_set(&apart->cores_clk_state, nbitpos, 1);
+		}
+	}
+
+	/*
+	 * Set the tiles in use bitmap.
+	 * In case of scanning, tiles which are powered on are considered as
+	 * tiles in use.
+	 */
+	bitmap_copy(apart->tiles_inuse.bitmap, apart->cores_clk_state.bitmap,
+		    apart->tiles_inuse.total);
+
+	return 0;
+}
+
+/* aie_set_col_clocks() - set clocks of a range of tiles of a column
+ * @apart: AI engine partition
+ * @range: range of tiles of a column
+ * @enable: true to enable the clock, false to disable
+ * @return: 0 for success, negative value of errors.
+ */
+static int aie_set_col_clocks(struct aie_partition *apart,
+			      struct aie_range *range, bool enable)
+{
+	struct aie_location ploc;
+	u32 startbit;
+
+	/*
+	 * check if the range is of single colum. only single column is allowed.
+	 * check if the start row is tile row, only tile rows are allowed.
+	 */
+	if (range->size.col != 1 || range->start.row < 1)
+		return -EINVAL;
+
+	ploc.col = range->start.col;
+	for (ploc.row = range->start.row - 1;
+	     ploc.row < range->start.row + range->size.row - 1;
+	     ploc.row++) {
+		struct aie_device *adev = apart->adev;
+		struct aie_aperture *aperture = apart->aperture;
+
+		if (!ploc.row) {
+			void __iomem *va;
+			u32 val = 0;
+
+			/*
+			 * Configure SHIM clock registers to gate or
+			 * ungate next tile.
+			 */
+			if (enable)
+				val = AIE_SHIMPL_CLKCNTR_COLBUF_MASK |
+				      AIE_SHIMPL_CLKCNTR_NEXTCLK_MASK;
+			va = aperture->base +
+			     aie_cal_regoff(adev, ploc,
+					    AIE_SHIMPL_CLKCNTR_REGOFF);
+			iowrite32(val, va);
+		} else {
+			void __iomem *va;
+			u32 val = 0;
+
+			/*
+			 * Configure core tile clock registers to gate
+			 * or ungate next tile.
+			 */
+			if (enable)
+				val = AIE_TILE_CLKCNTR_COLBUF_MASK |
+				      AIE_TILE_CLKCNTR_NEXTCLK_MASK;
+			va = aperture->base +
+			     aie_cal_regoff(adev, ploc,
+					    AIE_TILE_CORE_CLKCNTR_REGOFF);
+			iowrite32(val, va);
+		}
+
+		/* If the tile clock is not on, jump to next column */
+		if (!enable)
+			break;
+	}
+
+	/* Update clock state bitmap */
+	startbit = (range->start.col - apart->range.start.col) *
+		   (apart->range.size.row - 1) + range->start.row - 1;
+	if (enable)
+		aie_resource_set(&apart->cores_clk_state, startbit,
+				 range->size.row);
+	else
+		aie_resource_clear(&apart->cores_clk_state, startbit,
+				   range->size.row);
+
+	return 0;
+}
+
+static int aie_set_part_clocks(struct aie_partition *apart)
+{
+	struct aie_range *range = &apart->range, lrange;
+	struct aie_location rloc;
+
+	/*
+	 * The tiles below the highest tile whose clock is on, need to have the
+	 * clock on. The first for loop is to scan the clock states bitmap to
+	 * see which tiles are required to be clocked on, and update the bitmap
+	 * to make sure the tiles below are also required to be clocked on.
+	 */
+	for (rloc.col = 0; rloc.col < range->size.col; rloc.col++) {
+		u32 startbit, inuse_toprow = 0, clk_toprow = 0;
+
+		startbit = rloc.col * (range->size.row - 1);
+
+		for (rloc.row = range->start.row + 1;
+		     rloc.row < range->start.row + range->size.row;
+		     rloc.row++) {
+			u32 bit = startbit + rloc.row - 1;
+
+			if (aie_resource_testbit(&apart->tiles_inuse, bit))
+				inuse_toprow = rloc.row;
+			if (aie_resource_testbit(&apart->cores_clk_state, bit))
+				clk_toprow = rloc.row;
+		}
+
+		/* Update clock states of a column */
+		lrange.start.col = rloc.col + range->start.col;
+		lrange.size.col = 1;
+		if (inuse_toprow < clk_toprow) {
+			lrange.start.row = inuse_toprow + 1;
+			lrange.size.row = clk_toprow - inuse_toprow;
+			aie_set_col_clocks(apart, &lrange, false);
+		} else  if (inuse_toprow > clk_toprow) {
+			lrange.start.row = clk_toprow + 1;
+			lrange.size.row = inuse_toprow - clk_toprow;
+			aie_set_col_clocks(apart, &lrange, true);
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * aie_get_core_status() - read the AI engine core status register.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine core.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_core_status(struct aie_partition *apart,
+			       struct aie_location *loc)
+{
+	u32 regoff, regvalue, eventval;
+
+	regoff = aie_cal_regoff(apart->adev, *loc, aie_core_sts.regoff);
+	regvalue = ioread32(apart->aperture->base + regoff);
+
+	/* Apply core done workaround */
+	if (!FIELD_GET(aie_core_done.mask, regvalue)) {
+		regoff = aie_cal_regoff(apart->adev, *loc,
+					aie_core_disable_event_sts.regoff);
+		eventval = ioread32(apart->aperture->base + regoff);
+
+		if (FIELD_GET(aie_core_disable_event_sts.mask, eventval))
+			regvalue |= aie_core_done.mask;
+	}
+	return regvalue;
+}
+
+/**
+ * aie_part_clear_mems() - clear memories of every tile in a partition
+ * @apart: AI engine partition
+ * @return: return 0 always.
+ */
+static int aie_part_clear_mems(struct aie_partition *apart)
+{
+	struct aie_device *adev = apart->adev;
+	struct aie_part_mem *pmems = apart->pmems;
+	u32 i, num_mems;
+
+	/* Get the number of different types of memories */
+	num_mems = adev->ops->get_mem_info(adev, &apart->range, NULL);
+	if (!num_mems)
+		return 0;
+
+	/* Clear each type of memories in the partition */
+	for (i = 0; i < num_mems; i++) {
+		struct aie_mem *mem = &pmems[i].mem;
+		struct aie_range *range = &mem->range;
+		u32 c, r;
+
+		for (c = range->start.col;
+		     c < range->start.col + range->size.col; c++) {
+			for (r = range->start.row;
+			     r < range->start.row + range->size.row; r++) {
+				struct aie_location loc;
+				u32 memoff;
+
+				loc.col = c;
+				loc.row = r;
+				memoff = aie_cal_regoff(adev, loc, mem->offset);
+				memset_io(apart->aperture->base + memoff, 0,
+					  mem->size);
+			}
+		}
+	}
+
+	return 0;
+}
+
+static const struct aie_tile_operations aie_ops = {
+	.get_tile_type = aie_get_tile_type,
+	.get_mem_info = aie_get_mem_info,
+	.get_core_status = aie_get_core_status,
+	.reset_shim = aie_reset_shim,
+	.init_part_clk_state = aie_init_part_clk_state,
+	.scan_part_clocks = aie_scan_part_clocks,
+	.set_part_clocks = aie_set_part_clocks,
+	.mem_clear = aie_part_clear_mems,
+};
+
+/**
+ * aie_device_init_rscs_attr() - initialize AI engine device resources
+ *				 attributes
+ * @adev: AI engine device
+ */
+static void aie_device_init_rscs_attr(struct aie_device *adev)
+{
+	struct aie_tile_attr *tattr;
+
+	tattr = &adev->ttype_attr[AIE_TILE_TYPE_TILE];
+	tattr->num_mods = 2;
+	tattr->rscs_attr = aie_core_tile_rscs_attr;
+	tattr->mods = aie_core_tile_module_types;
+
+	tattr = &adev->ttype_attr[AIE_TILE_TYPE_SHIMPL];
+	tattr->num_mods = 1;
+	tattr->rscs_attr = aie_shimpl_tile_rscs_attr;
+	tattr->mods = aie_shimpl_tile_module_types;
+
+	/*
+	 * For now, SHIMNOC is the same as SHIMPL as there is
+	 * no SHIMNOC specific resources managed by kernel
+	 * driver yet.
+	 */
+	tattr = &adev->ttype_attr[AIE_TILE_TYPE_SHIMNOC];
+	tattr->num_mods = 1;
+	tattr->rscs_attr = aie_shimpl_tile_rscs_attr;
+	tattr->mods = aie_shimpl_tile_module_types;
+}
+
+/**
+ * aie_device_init() - Initialize AI engine device struct AIE specific
+ * @adev: AI engine device
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function initialize the AI engine device structure device version
+ * specific elements such as register addressing related array shift,
+ * column shift, and row shift; AIE device specific device operations, device
+ * columns resource.
+ */
+int aie_device_init(struct aie_device *adev)
+{
+	adev->array_shift = AIE_ARRAY_SHIFT;
+	adev->col_shift = AIE_COL_SHIFT;
+	adev->row_shift = AIE_ROW_SHIFT;
+	adev->ops = &aie_ops;
+	adev->num_kernel_regs = ARRAY_SIZE(aie_kernel_regs);
+	adev->kernel_regs = aie_kernel_regs;
+	adev->num_core_regs = ARRAY_SIZE(aie_core_regs);
+	adev->core_regs = aie_core_regs;
+	adev->col_rst = &aie_col_rst;
+	adev->col_clkbuf = &aie_col_clkbuf;
+	adev->shim_dma = &aie_shimdma;
+	adev->tile_dma = &aie_tiledma;
+	adev->pl_events = &aie_pl_event;
+	adev->mem_events = &aie_mem_event;
+	adev->core_events = &aie_core_event;
+	adev->l1_ctrl = &aie_l1_intr_ctrl;
+	adev->l2_ctrl = &aie_l2_intr_ctrl;
+	adev->core_errors = &aie_core_error;
+	adev->mem_errors = &aie_mem_error;
+	adev->shim_errors = &aie_shim_error;
+	adev->part_sysfs_attr = &aie_part_sysfs_attr;
+	adev->tile_sysfs_attr = &aie_tile_sysfs_attr;
+	adev->core_status_str = aie_core_status_str;
+	adev->core_pc = &aie_core_pc;
+	adev->core_lr = &aie_core_lr;
+	adev->core_sp = &aie_core_sp;
+	adev->dma_status_str = aie_dma_status_str;
+	adev->queue_status_str = aie_queue_status_str;
+	adev->pl_lock = &aie_pl_lock;
+	adev->mem_lock = &aie_mem_lock;
+	adev->lock_status_str = aie_lock_status_str;
+
+	aie_device_init_rscs_attr(adev);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-aieml.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-aieml.c
@@ -0,0 +1,433 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine driver AIE-ML device specific implementation
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+#define AIEML_ARRAY_SHIFT	32U
+#define AIEML_COL_SHIFT		25U
+#define AIEML_ROW_SHIFT		20U
+
+#define NUM_TYPES_OF_MEM	3U
+
+/*
+ * Register offsets
+ */
+#define AIEML_SHIMNOC_AXIMM_REGOFF			0x0001e020U
+#define AIEML_SHIMNOC_BD0_0_REGOFF			0x0001d000U
+#define AIEML_SHIMNOC_BD15_7_REGOFF			0x0001d1fcU
+#define AIEML_SHIMNOC_L2INTR_MASK_REGOFF		0x00015000U
+#define AIEML_SHIMNOC_L2INTR_INTR_REGOFF		0x00015010U
+#define AIEML_SHIMPL_BISRCACHE_CTRL_REGOFF		0x00036000U
+#define AIEML_SHIMPL_COLCLOCK_CTRL_REGOFF		0x000fff20U
+#define AIEML_SHIMPL_COLRESET_CTRL_REGOFF		0x000fff28U
+#define AIEML_SHIMPL_GROUPERROR_REGOFF			0x0003450cU
+#define AIEML_SHIMPL_L1INTR_MASK_A_REGOFF		0x00035000U
+#define AIEML_SHIMPL_L1INTR_BLOCK_NORTH_B_REGOFF	0x00035050U
+#define AIEML_SHIMPL_MODCLOCK_CTRL_0_REGOFF		0x000fff00U
+#define AIEML_SHIMPL_MODCLOCK_CTRL_1_REGOFF		0x000fff04U
+#define AIEML_SHIMPL_MODRESET_CTRL_0_REGOFF		0x000fff10U
+#define AIEML_SHIMPL_MODRESET_CTRL_1_REGOFF		0x000fff14U
+#define AIEML_MEMORY_GROUPERROR_REGOFF			0x00094518U
+#define AIEML_MEMORY_MEMCTRL_REGOFF			0x00096048U
+#define AIEML_MEMORY_MODCLOCKCTRL_REGOFF		0x000fff00U
+#define AIEML_MEMORY_MODRESETCTRL_REGOFF		0x000fff10U
+#define AIEML_TILE_COREMOD_AMLL0_PART1_REGOFF		0x00030000U
+#define AIEML_TILE_COREMOD_AMHH8_PART2_REGOFF		0x00030470U
+#define AIEML_TILE_COREMOD_GROUPERROR_REGOFF		0x00034510U
+#define AIEML_TILE_COREMOD_MEMCTRL_REGOFF		0x00036070U
+#define AIEML_TILE_COREMOD_MODCLOCKCTRL_REGOFF		0x00060000U
+#define AIEML_TILE_COREMOD_MODRESETCTRL_REGOFF		0x00060010U
+#define AIEML_TILE_COREMOD_WL0_PART1_REGOFF		0x00030800U
+#define AIEML_TILE_COREMOD_WH11_PART2_REGOFF		0x00030af0U
+#define AIEML_TILE_COREMOD_R0_REGOFF			0x00030c00U
+#define AIEML_TILE_COREMOD_R31_REGOFF			0x00030df0U
+#define AIEML_TILE_MEMMOD_GROUPERROR_REGOFF		0x00014514U
+#define AIEML_TILE_MEMMOD_MEMCTRL_REGOFF		0x00016010U
+
+/*
+ * Register masks
+ */
+#define AIEML_SHIMPL_COLRESET_CTRL_MASK			GENMASK(1, 0)
+#define AIEML_SHIMPL_COLCLOCK_CTRL_MASK			GENMASK(1, 0)
+
+static const struct aie_tile_regs aieml_kernel_regs[] = {
+	/* SHIM AXI MM Config */
+	{.attribute = AIE_TILE_TYPE_MASK_SHIMNOC << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMNOC_AXIMM_REGOFF,
+	 .eoff = AIEML_SHIMNOC_AXIMM_REGOFF,
+	},
+	/* SHIM DMA buffer descriptor address range */
+	{.attribute = AIE_TILE_TYPE_MASK_SHIMNOC << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMNOC_BD0_0_REGOFF,
+	 .eoff = AIEML_SHIMNOC_BD15_7_REGOFF,
+	},
+	/* SHIM 2nd level interrupt controller */
+	{.attribute = AIE_TILE_TYPE_MASK_SHIMNOC << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMNOC_L2INTR_MASK_REGOFF,
+	 .eoff = AIEML_SHIMNOC_L2INTR_INTR_REGOFF,
+	},
+	/* SHIM BISR cache control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_BISRCACHE_CTRL_REGOFF,
+	 .eoff = AIEML_SHIMPL_BISRCACHE_CTRL_REGOFF,
+	},
+	/* SHIM column clock control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_COLCLOCK_CTRL_REGOFF,
+	 .eoff = AIEML_SHIMPL_COLCLOCK_CTRL_REGOFF,
+	},
+	/* SHIM column reset control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_COLRESET_CTRL_REGOFF,
+	 .eoff = AIEML_SHIMPL_COLRESET_CTRL_REGOFF,
+	},
+	/* SHIM group error enable */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		      AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_GROUPERROR_REGOFF,
+	 .eoff = AIEML_SHIMPL_GROUPERROR_REGOFF,
+	},
+	/* SHIM 1st level interrupt controller */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_L1INTR_MASK_A_REGOFF,
+	 .eoff = AIEML_SHIMPL_L1INTR_BLOCK_NORTH_B_REGOFF,
+	},
+	/* SHIM module clock control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_MODCLOCK_CTRL_0_REGOFF,
+	 .eoff = AIEML_SHIMPL_MODCLOCK_CTRL_1_REGOFF,
+	},
+	/* SHIM module reset control */
+	{.attribute = (AIE_TILE_TYPE_MASK_SHIMPL | AIE_TILE_TYPE_MASK_SHIMNOC) <<
+		AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_SHIMPL_MODRESET_CTRL_0_REGOFF,
+	 .eoff = AIEML_SHIMPL_MODRESET_CTRL_1_REGOFF,
+	},
+	/* MEMORY tile group error enable */
+	{.attribute = AIE_TILE_TYPE_MASK_MEMORY << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_MEMORY_GROUPERROR_REGOFF,
+	 .eoff = AIEML_MEMORY_GROUPERROR_REGOFF,
+	},
+	/* MEMORY tile mem control */
+	{.attribute = AIE_TILE_TYPE_MASK_MEMORY << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_MEMORY_MEMCTRL_REGOFF,
+	 .eoff = AIEML_MEMORY_MEMCTRL_REGOFF,
+	},
+	/* MEMORY tile module clock control */
+	{.attribute = AIE_TILE_TYPE_MASK_MEMORY << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_MEMORY_MODCLOCKCTRL_REGOFF,
+	 .eoff = AIEML_MEMORY_MODCLOCKCTRL_REGOFF,
+	},
+	/* MEMORY tile module reset control */
+	{.attribute = AIE_TILE_TYPE_MASK_MEMORY << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_MEMORY_MODRESETCTRL_REGOFF,
+	 .eoff = AIEML_MEMORY_MODRESETCTRL_REGOFF,
+	},
+	/* TILE core module group error enable */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_TILE_COREMOD_GROUPERROR_REGOFF,
+	 .eoff = AIEML_TILE_COREMOD_GROUPERROR_REGOFF,
+	},
+	/* TILE memory control */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_TILE_COREMOD_MEMCTRL_REGOFF,
+	 .eoff = AIEML_TILE_COREMOD_MEMCTRL_REGOFF,
+	},
+	/* TILE module clock control */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_TILE_COREMOD_MODCLOCKCTRL_REGOFF,
+	 .eoff = AIEML_TILE_COREMOD_MODCLOCKCTRL_REGOFF,
+	},
+	/* TILE module reset control */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_TILE_COREMOD_MODRESETCTRL_REGOFF,
+	 .eoff = AIEML_TILE_COREMOD_MODRESETCTRL_REGOFF,
+	},
+	/* TILE memory module group error enable */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_TILE_MEMMOD_GROUPERROR_REGOFF,
+	 .eoff = AIEML_TILE_MEMMOD_GROUPERROR_REGOFF,
+	},
+	/* TILE memory module mem control */
+	{.attribute = AIE_TILE_TYPE_MASK_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	 .soff = AIEML_TILE_MEMMOD_MEMCTRL_REGOFF,
+	 .eoff = AIEML_TILE_MEMMOD_MEMCTRL_REGOFF,
+	},
+};
+
+static const struct aie_tile_regs aieml_core_amxx_regs = {
+	.attribute = AIE_TILE_TYPE_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	.soff = AIEML_TILE_COREMOD_AMLL0_PART1_REGOFF,
+	.eoff = AIEML_TILE_COREMOD_AMHH8_PART2_REGOFF,
+};
+
+static const struct aie_tile_regs aieml_core_wx_regs = {
+	.attribute = AIE_TILE_TYPE_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	.soff = AIEML_TILE_COREMOD_WL0_PART1_REGOFF,
+	.eoff = AIEML_TILE_COREMOD_WH11_PART2_REGOFF,
+};
+
+static const struct aie_tile_regs aieml_core_32bit_regs = {
+	.attribute = AIE_TILE_TYPE_TILE << AIE_REGS_ATTR_TILE_TYPE_SHIFT,
+	.soff = AIEML_TILE_COREMOD_R0_REGOFF,
+	.eoff = AIEML_TILE_COREMOD_R31_REGOFF,
+};
+
+static const struct aie_core_regs_attr aieml_core_regs[] = {
+	{.core_regs = &aieml_core_amxx_regs,
+	 .width = 4,
+	},
+	{.core_regs = &aieml_core_wx_regs,
+	 .width = 4,
+	},
+	{.core_regs = &aieml_core_32bit_regs,
+	 .width = 1,
+	},
+};
+
+static const struct aie_single_reg_field aieml_col_rst = {
+	.mask = AIEML_SHIMPL_COLRESET_CTRL_MASK,
+	.regoff = AIEML_SHIMPL_COLRESET_CTRL_REGOFF,
+};
+
+static const struct aie_single_reg_field aieml_col_clkbuf = {
+	.mask = AIEML_SHIMPL_COLCLOCK_CTRL_MASK,
+	.regoff = AIEML_SHIMPL_COLCLOCK_CTRL_REGOFF,
+};
+
+static const struct aie_dma_attr aieml_shimdma = {
+	.laddr = {
+		.mask = 0xfffffffcU,
+		.regoff = 0x4U,
+	},
+	.haddr = {
+		.mask = 0xffffU,
+		.regoff = 0x8U,
+	},
+	.buflen = {
+		.mask = 0xffffffffU,
+		.regoff = 0x0U,
+	},
+	.bd_regoff = AIEML_SHIMNOC_BD0_0_REGOFF,
+	.num_bds = 16,
+	.bd_len = 0x20U,
+};
+
+static u32 aieml_get_tile_type(struct aie_device *adev,
+			       struct aie_location *loc)
+{
+	u8 num_mem_rows = adev->ttype_attr[AIE_TILE_TYPE_MEMORY].num_rows;
+
+	if (loc->row > num_mem_rows)
+		return AIE_TILE_TYPE_TILE;
+	if (loc->row && loc->row <= num_mem_rows)
+		return AIE_TILE_TYPE_MEMORY;
+	if (loc->row == 0)
+		if ((loc->col % 4) < 2)
+			return AIE_TILE_TYPE_SHIMPL;
+
+	return AIE_TILE_TYPE_SHIMNOC;
+}
+
+static unsigned int aieml_get_mem_info(struct aie_device *adev,
+				       struct aie_range *range,
+				       struct aie_part_mem *pmem)
+{
+	unsigned int i;
+	u8 start_row, num_rows;
+
+	if (range->start.row + range->size.row <= 1) {
+		/* SHIM row only, no memories in this range */
+		return 0;
+	}
+
+	if (!pmem)
+		return NUM_TYPES_OF_MEM;
+
+	for (i = 0; i < NUM_TYPES_OF_MEM; i++) {
+		struct aie_mem *mem = &pmem[i].mem;
+
+		memcpy(&mem->range, range, sizeof(*range));
+	}
+
+	start_row = adev->ttype_attr[AIE_TILE_TYPE_TILE].start_row;
+	num_rows = adev->ttype_attr[AIE_TILE_TYPE_TILE].num_rows;
+	/* Setup tile data memory information */
+	pmem[0].mem.offset = 0;
+	pmem[0].mem.size = KBYTES(64);
+	pmem[0].mem.range.start.row = start_row;
+	pmem[0].mem.range.size.row = num_rows;
+
+	/* Setup program memory information */
+	pmem[1].mem.offset = 0x20000;
+	pmem[1].mem.size = KBYTES(16);
+	pmem[1].mem.range.start.row = start_row;
+	pmem[1].mem.range.size.row = num_rows;
+
+	start_row = adev->ttype_attr[AIE_TILE_TYPE_MEMORY].start_row;
+	num_rows = adev->ttype_attr[AIE_TILE_TYPE_MEMORY].num_rows;
+	/* Setup memory tile memory information */
+	pmem[2].mem.offset = 0;
+	pmem[2].mem.size = KBYTES(512);
+	pmem[2].mem.range.start.row = start_row;
+	pmem[2].mem.range.size.row = num_rows;
+
+	return NUM_TYPES_OF_MEM;
+}
+
+static int aieml_reset_shim(struct aie_aperture *aperture,
+			    struct aie_range *range)
+{
+	u32 node_id = aperture->adev->pm_node_id;
+	int ret;
+
+	ret = zynqmp_pm_aie_operation(node_id, range->start.col,
+				      range->size.col,
+				      XILINX_AIE_OPS_COL_RST |
+				      XILINX_AIE_OPS_SHIM_RST);
+	if (ret < 0)
+		dev_err(&aperture->dev,
+			"failed to perform shim and column reset.\n");
+
+	return ret;
+}
+
+static int aieml_init_part_clk_state(struct aie_partition *apart)
+{
+	int ret, num_tiles;
+
+	num_tiles = apart->range.size.col * apart->range.size.row - 1;
+
+	ret = aie_resource_initialize(&apart->cores_clk_state, num_tiles);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to initialize tiles clock state resource.\n");
+		return ret;
+	}
+
+	ret = aie_resource_initialize(&apart->tiles_inuse, num_tiles);
+	if (ret)
+		dev_err(&apart->dev,
+			"failed to initialize tiles in use resource.\n");
+
+	return ret;
+}
+
+static int aieml_scan_part_clocks(struct aie_partition *apart)
+{
+	struct aie_device *adev = apart->adev;
+	struct aie_aperture *aperture = apart->aperture;
+	struct aie_range *range = &apart->range;
+	struct aie_location loc;
+
+	/* Clear the bitmap of cores and memories clock state */
+	aie_resource_put_region(&apart->cores_clk_state, 0,
+				apart->cores_clk_state.total);
+
+	/*
+	 * In aieml if clock buffer on shim tile is enabled, the clock for all
+	 * tiles in the same column is enabled.
+	 */
+
+	loc.row = 0;
+	for (loc.col = range->start.col;
+	     loc.col < range->start.col + range->size.col;
+	     loc.col++) {
+		void __iomem *va;
+		u32 val, nbitpos;
+
+		nbitpos = loc.col * (range->size.row - 1) + loc.row;
+
+		va = aperture->base +
+		     aie_cal_regoff(adev, loc,
+				    AIEML_SHIMPL_COLCLOCK_CTRL_REGOFF);
+		val = ioread32(va);
+
+		if (!(val & AIEML_SHIMPL_COLCLOCK_CTRL_MASK))
+			continue;
+
+		aie_resource_set(&apart->cores_clk_state, nbitpos,
+				 range->size.row - 1);
+	}
+	/*
+	 * Set the tiles in use bitmap.
+	 * In case of scanning, tiles which are powered on are considered as
+	 * tiles in use.
+	 */
+	bitmap_copy(apart->tiles_inuse.bitmap, apart->cores_clk_state.bitmap,
+		    apart->tiles_inuse.total);
+
+	return 0;
+}
+
+static int aieml_set_part_clocks(struct aie_partition *apart)
+{
+	struct aie_range *range = &apart->range;
+	u32 node_id = apart->adev->pm_node_id;
+	int ret;
+
+	ret = zynqmp_pm_aie_operation(node_id, range->start.col,
+				      range->size.col,
+				      XILINX_AIE_OPS_ENB_COL_CLK_BUFF);
+	if (ret < 0)
+		dev_err(&apart->dev, "failed to enable clocks for partition\n");
+
+	return ret;
+}
+
+static int aieml_part_clear_mems(struct aie_partition *apart)
+{
+	struct aie_range *range = &apart->range;
+	u32 node_id = apart->adev->pm_node_id;
+	int ret;
+
+	ret = zynqmp_pm_aie_operation(node_id, range->start.col,
+				      range->size.col,
+				      XILINX_AIE_OPS_ZEROISATION);
+	if (ret < 0)
+		dev_err(&apart->dev, "failed to clear memory for partition\n");
+
+	return ret;
+}
+
+static const struct aie_tile_operations aieml_ops = {
+	.get_tile_type = aieml_get_tile_type,
+	.get_mem_info = aieml_get_mem_info,
+	.reset_shim = aieml_reset_shim,
+	.init_part_clk_state = aieml_init_part_clk_state,
+	.scan_part_clocks = aieml_scan_part_clocks,
+	.set_part_clocks = aieml_set_part_clocks,
+	.mem_clear = aieml_part_clear_mems,
+};
+
+int aieml_device_init(struct aie_device *adev)
+{
+	adev->array_shift = AIEML_ARRAY_SHIFT;
+	adev->col_shift = AIEML_COL_SHIFT;
+	adev->row_shift = AIEML_ROW_SHIFT;
+	adev->ops = &aieml_ops;
+	adev->num_kernel_regs = ARRAY_SIZE(aieml_kernel_regs);
+	adev->kernel_regs = aieml_kernel_regs;
+	adev->num_core_regs = ARRAY_SIZE(aieml_core_regs);
+	adev->core_regs = aieml_core_regs;
+	adev->col_rst = &aieml_col_rst;
+	adev->col_clkbuf = &aieml_col_clkbuf;
+	adev->shim_dma = &aieml_shimdma;
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-aperture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-aperture.c
@@ -0,0 +1,523 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine partition driver
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ */
+
+#include <linux/bitmap.h>
+#include <linux/device.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <uapi/linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+/* AI engine SHIM DMA address width is 48bits */
+#define XAIE_DMA_BIT_MASK	48U
+
+/**
+ * aie_aperture_get_num_parts() - get number of AI engine partitions of aperture
+ * @aperture: AI engine aperture
+ * @return: number of partitions of this aperture
+ *
+ * This function returns the number of AI engine partitions of the aperture.
+ * It includes the number of partitions in use and the number of available
+ * of partitions. If no partitions are in use, the number of available
+ * partitions is 1. One available partition is the max contiguous available
+ * columns region. E.g. if there is only one partition in use starting from
+ * column 10 to 14 in the aperture. The number of all partitions of this
+ * aperture is 3. They are column 0 to 9, 10 to 14 and 15+. This function
+ * returns 3, for which columns for each partition, and whether they are in
+ * use will be returned by another function @aie_aperture_enquire_parts().
+ */
+unsigned int aie_aperture_get_num_parts(struct aie_aperture *aperture)
+{
+	struct aie_partition *apart;
+	int ret;
+	unsigned int rs, re, num_parts = 0;
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret)
+		return ret;
+
+	list_for_each_entry(apart, &aperture->partitions, node) {
+		num_parts++;
+	}
+
+	bitmap_for_each_clear_region(aperture->cols_res.bitmap, rs, re, 0,
+				     (aperture->range.size.col - 1)) {
+		num_parts++;
+	}
+
+	mutex_unlock(&aperture->mlock);
+
+	return num_parts;
+}
+
+/**
+ * aie_aperture_enquire_parts() - get partitions information
+ * @aperture: AI engine aperture`
+ * @num_queries: number of queries entries to return
+ * @queries: return the partitions information
+ * @num_parts_left: number of partitions not filled
+ * @to_user: indicate it if information is required to user space
+ * @return: number of partitions have been filled in if succeeded,
+ *	    negative value for error.
+ *
+ * This function returns each columns information and if the partition is
+ * in use for each partition until the queries array is filled up. The
+ * @num_parts_left will contains the partitions whose information are not
+ * able to put into the queries due to the queries array is full.
+ * Internal function, will not validate the queries, and num_parts_left
+ * pointers. Caller should not pass invalid values.
+ */
+int aie_aperture_enquire_parts(struct aie_aperture *aperture,
+			       unsigned int num_queries,
+			       struct aie_range_args  *queries,
+			       int *num_parts_left, bool to_user)
+{
+	struct aie_partition *apart;
+	int ret;
+	unsigned int rs, re, num_queries_left;
+
+	*num_parts_left = 0;
+	num_queries_left = num_queries;
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret)
+		return ret;
+
+	list_for_each_entry(apart, &aperture->partitions, node) {
+		struct aie_range_args query;
+
+		if (!num_queries_left) {
+			*num_parts_left += 1;
+			continue;
+		}
+		query.partition_id = apart->range.start.col <<
+				     AIE_PART_ID_START_COL_SHIFT;
+		query.partition_id += apart->range.size.col <<
+				      AIE_PART_ID_NUM_COLS_SHIFT;
+		query.range.start.col = apart->range.start.col;
+		query.range.size.col = apart->range.size.col;
+		query.range.start.row = apart->range.start.row;
+		query.range.size.row = apart->range.size.row;
+		query.status = apart->status;
+
+		if (to_user) {
+			if (copy_to_user((void __user *)queries, &query,
+					 sizeof(query))) {
+				mutex_unlock(&aperture->mlock);
+				return -EFAULT;
+			}
+		} else {
+			memcpy(queries, &query, sizeof(query));
+		}
+		queries++;
+		num_queries_left--;
+	}
+
+	bitmap_for_each_clear_region(aperture->cols_res.bitmap, rs, re, 0,
+				     (aperture->range.size.col - 1)) {
+		struct aie_range_args query;
+
+		if (!num_queries_left) {
+			*num_parts_left += 1;
+			continue;
+		}
+		query.partition_id = (rs & AIE_PART_ID_START_COL_MASK) <<
+				     AIE_PART_ID_START_COL_SHIFT;
+		query.partition_id += ((re - rs + 1) &
+				       AIE_PART_ID_NUM_COLS_MASK) <<
+				      AIE_PART_ID_NUM_COLS_SHIFT;
+		query.range.start.col = rs;
+		query.range.size.col = re - rs + 1;
+		query.range.start.row = aperture->range.start.row;
+		query.range.size.row = aperture->range.size.row;
+		query.status = 0;
+
+		if (to_user) {
+			if (copy_to_user((void __user *)queries, &query,
+					 sizeof(query))) {
+				mutex_unlock(&aperture->mlock);
+				return -EFAULT;
+			}
+		} else {
+			memcpy(queries, &query, sizeof(query));
+		}
+		queries++;
+		num_queries_left--;
+	}
+
+	mutex_unlock(&aperture->mlock);
+
+	return (num_queries - num_queries_left);
+}
+
+/**
+ * aie_aperture_request_part_from_id() - request AI engine partition from id
+ * @aperture: AI engine aperture
+ * @partition_id: partition id to check
+ * @return: partition pointer for success, and error pointer for failure
+ *
+ * The partition ID contains the start column and number of columns
+ * information for the partition.
+ */
+struct aie_partition *
+aie_aperture_request_part_from_id(struct aie_aperture *aperture,
+				  u32 partition_id)
+{
+	struct aie_partition *apart = NULL;
+	u32 in_partition_id = partition_id;
+	u8 start_col, num_cols;
+	int ret;
+
+	start_col = aie_part_id_get_start_col(partition_id);
+	num_cols = aie_part_id_get_num_cols(partition_id);
+	/*
+	 * TODO: this is for backward compatibility, once zocl update
+	 * to pass the expected partition id format, can remove the
+	 * num_cols.
+	 */
+	if (num_cols == 0) {
+		start_col = aperture->range.start.col;
+		num_cols = aperture->range.size.col;
+		partition_id = ((u32)start_col << AIE_PART_ID_START_COL_SHIFT) |
+			       ((u32)num_cols << AIE_PART_ID_NUM_COLS_SHIFT);
+	}
+
+	if (start_col < aperture->range.start.col ||
+	    num_cols > aperture->range.size.col ||
+	    (start_col + num_cols) >
+	    (aperture->range.start.col + aperture->range.size.col)) {
+		dev_err(&aperture->dev, "invalid partition %u: %u,%u.\n",
+			partition_id, start_col, num_cols);
+		return ERR_PTR(-EINVAL);
+	}
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret)
+		return ERR_PTR(ret);
+
+	ret = aie_resource_get_region(&aperture->cols_res, start_col, num_cols);
+	if (ret != (u32)start_col) {
+		dev_err(&aperture->dev, "partition %u already requested.\n",
+			in_partition_id);
+		mutex_unlock(&aperture->mlock);
+		return ERR_PTR(-EINVAL);
+	}
+
+	apart = aie_create_partition(aperture, partition_id);
+	if (IS_ERR(apart)) {
+		dev_err(&aperture->dev, "failed to create partition %u.\n",
+			partition_id);
+		mutex_unlock(&aperture->mlock);
+		return apart;
+	}
+
+	list_add_tail(&apart->node, &aperture->partitions);
+
+	mutex_unlock(&aperture->mlock);
+
+	return apart;
+}
+
+/**
+ * aie_aperture_check_part_avail() - Check an AI engine partition availability
+ * @aperture: AI engine aperture
+ * @req: AI engine partition requesting arguments
+ * @return: if AI engine partition is available, in use or not valid for the
+ *	    aperture.
+ *
+ * This functions checks the specified partition availability in the aperture.
+ * This function is internal call, it will not valid the input pointers.
+ */
+int aie_aperture_check_part_avail(struct aie_aperture *aperture,
+				  struct aie_partition_req *req)
+{
+	unsigned int start_col, end_col, num_cols;
+
+	start_col = aie_part_id_get_start_col(req->partition_id);
+	num_cols = aie_part_id_get_num_cols(req->partition_id);
+	/*
+	 * TODO: this is for backward compatibility, once zocl update
+	 * to pass the expected partition id format, can remove the
+	 * num_cols.
+	 */
+	if (num_cols == 0) {
+		start_col = aperture->range.start.col;
+		num_cols = aperture->range.size.col;
+	}
+
+	end_col = start_col + num_cols - 1;
+
+	if (start_col < aperture->range.start.col ||
+	    end_col >= aperture->range.start.col + aperture->range.size.col) {
+		return XAIE_PART_STATUS_INVALID;
+	}
+
+	if (aie_resource_check_region(&aperture->cols_res, start_col,
+				      num_cols) < 0)
+		return XAIE_PART_STATUS_INUSE;
+
+	return XAIE_PART_STATUS_IDLE;
+}
+
+/**
+ * aie_aperture_release_device() - release an AI engine aperture instance
+ * @dev: AI engine aperture device
+ *
+ * It will be called by device driver core when no one holds a valid
+ * pointer to @dev anymore.
+ */
+static void aie_aperture_release_device(struct device *dev)
+{
+	struct aie_aperture *aperture = dev_get_drvdata(dev);
+
+	aie_resource_uninitialize(&aperture->cols_res);
+	aie_resource_uninitialize(&aperture->l2_mask);
+	zynqmp_pm_release_node(aperture->node_id);
+	kfree(aperture);
+}
+
+/**
+ * aie_aperture_remove() - destroy AI engine aperture
+ * @aperture: AI engine aperture
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will remove AI engine aperture.
+ */
+int aie_aperture_remove(struct aie_aperture *aperture)
+{
+	struct list_head *node, *pos;
+	int ret;
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret)
+		return ret;
+
+	list_for_each_safe(pos, node, &aperture->partitions) {
+		struct aie_partition *apart;
+
+		apart = list_entry(pos, struct aie_partition, node);
+		list_del(&apart->node);
+		aie_part_remove(apart);
+	}
+	mutex_unlock(&aperture->mlock);
+
+	of_node_clear_flag(aperture->dev.of_node, OF_POPULATED);
+	device_del(&aperture->dev);
+	put_device(&aperture->dev);
+
+	return 0;
+}
+
+/**
+ * aie_aperture_add_dev() - initialize and add AI engine aperture device
+ * @aperture: AI engine aperture
+ * @nc: AI engine aperture device node
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will initialize and add AI engine aperture device to Linux
+ * kernel device framework.
+ * TODO: This function should be moved back to of_aie_aperture_probe()
+ * implementation once v1.0 device node support is removed.
+ */
+int aie_aperture_add_dev(struct aie_aperture *aperture,
+			 struct device_node *nc)
+{
+	struct device *dev = &aperture->dev;
+
+	/* register device for aperture */
+	dev = &aperture->dev;
+	dev->class = aie_class;
+	dev->parent = &aperture->adev->dev;
+	dev->of_node = nc;
+	dev->driver_data = aperture;
+	dev_set_name(dev, "aieaperture_%u_%u", aperture->range.start.col,
+		     aperture->range.size.col);
+	/* We can now rely on the release function for cleanup */
+	dev->release = aie_aperture_release_device;
+
+	return device_register(&aperture->dev);
+}
+
+/**
+ * of_aie_aperture_probe() - probes AI engine aperture node
+ * @adev: AI engine device
+ * @nc: aperture device node
+ * @return: AI engine aperture pointer for success, error pointer for failure.
+ *
+ * This function will probe AI engine aperture node and will create an AI
+ * engine aperture instance for the node.
+ * It requires the caller to lock the @adev before calling this function.
+ */
+struct aie_aperture *
+of_aie_aperture_probe(struct aie_device *adev, struct device_node *nc)
+{
+	struct aie_aperture *aperture, *laperture;
+	struct device *dev;
+	struct aie_range *range;
+	u32 regs[2];
+	int ret;
+
+	aperture = kzalloc(sizeof(*aperture), GFP_KERNEL);
+	if (!aperture)
+		return ERR_PTR(-ENOMEM);
+
+	aperture->adev = adev;
+	INIT_LIST_HEAD(&aperture->partitions);
+	mutex_init(&aperture->mlock);
+
+	range = &aperture->range;
+	ret = of_property_read_u32_array(nc, "xlnx,columns", regs,
+					 ARRAY_SIZE(regs));
+	if (ret < 0) {
+		dev_err(&adev->dev,
+			"probe %pOF failed, no tiles range information.\n",
+			nc);
+		goto free_aperture;
+	}
+	range->start.col = regs[0] & aligned_byte_mask(1);
+	range->size.col = regs[1] & aligned_byte_mask(1);
+
+	/*
+	 * Row information is used to calculate the clock or other resources
+	 * bitmaps. It can be moved aie_device later.
+	 */
+	range->start.row = 0;
+	range->size.row = adev->ttype_attr[AIE_TILE_TYPE_SHIMPL].num_rows +
+			  adev->ttype_attr[AIE_TILE_TYPE_MEMORY].num_rows +
+			  adev->ttype_attr[AIE_TILE_TYPE_TILE].num_rows;
+
+	ret = of_property_read_u32_index(nc, "xlnx,node-id", 0,
+					 &aperture->node_id);
+	if (ret < 0) {
+		dev_err(&adev->dev,
+			"probe %pOF failed, no aperture node id.\n", nc);
+		goto free_aperture;
+	}
+
+	/* Validate the aperture */
+	list_for_each_entry(laperture, &adev->apertures, node) {
+		u32 start_col, end_col, check_start_col, check_end_col;
+
+		if (laperture->node_id == aperture->node_id) {
+			dev_err(&adev->dev,
+				"probe failed, aperture %u exists.\n",
+				aperture->node_id);
+			ret = -EINVAL;
+			goto free_aperture;
+		}
+
+		start_col = range->start.col;
+		end_col  = start_col + range->size.col - 1;
+		check_start_col = laperture->range.start.col;
+		check_end_col = check_start_col + laperture->range.size.col - 1;
+		if ((start_col >= check_start_col &&
+		     start_col <= check_end_col) ||
+		    (end_col >= check_start_col &&
+		     end_col <= check_end_col)) {
+			dev_err(&adev->dev,
+				"probe failed, aperture %u overlaps other aperture.\n",
+				aperture->node_id);
+			ret = -EINVAL;
+			goto free_aperture;
+		}
+	}
+
+	/* register device for aperture */
+	ret = aie_aperture_add_dev(aperture, nc);
+	if (ret) {
+		dev_err(&aperture->dev, "device_add failed: %d\n", ret);
+		goto free_aperture;
+	}
+	dev = &aperture->dev;
+
+	/*
+	 * Initialize columns resource map to remember which columns have been
+	 * assigned. Used for partition management.
+	 */
+	ret = aie_resource_initialize(&aperture->cols_res,
+				      aperture->range.size.col);
+	if (ret) {
+		dev_err(dev, "failed to initialize columns resource.\n");
+		goto put_aperture_dev;
+	}
+
+	ret = of_address_to_resource(nc, 0, &aperture->res);
+	if (ret < 0) {
+		dev_err(dev, "failed to get address from device node.\n");
+		goto put_aperture_dev;
+	}
+	aperture->base = devm_ioremap_resource(dev, &aperture->res);
+	if (!aperture->base) {
+		ret = -ENOMEM;
+		goto put_aperture_dev;
+	}
+
+	/* Get device node DMA setting */
+	dev->coherent_dma_mask = DMA_BIT_MASK(XAIE_DMA_BIT_MASK);
+	dev->dma_mask = &dev->coherent_dma_mask;
+	ret = of_dma_configure(&aperture->dev, nc, true);
+	if (ret)
+		dev_warn(&aperture->dev, "Failed to configure DMA.\n");
+
+	/* Initialize interrupt */
+	ret = of_irq_get_byname(nc, "interrupt1");
+	if (ret < 0) {
+		dev_warn(dev, "no interrupt in device node.");
+	} else {
+		aperture->irq = ret;
+		INIT_WORK(&aperture->backtrack, aie_aperture_backtrack);
+		ret = aie_aperture_create_l2_bitmap(aperture);
+		if (ret) {
+			dev_err(dev,
+				"failed to initialize l2 mask resource.\n");
+			goto put_aperture_dev;
+		}
+
+		ret = devm_request_threaded_irq(dev, aperture->irq, NULL,
+						aie_interrupt, IRQF_ONESHOT,
+						dev_name(dev), aperture);
+		if (ret) {
+			dev_err(dev, "Failed to request AIE IRQ.\n");
+			goto put_aperture_dev;
+		}
+	}
+
+	ret = zynqmp_pm_request_node(aperture->node_id,
+				     ZYNQMP_PM_CAPABILITY_ACCESS, 0,
+				     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+	if (ret < 0) {
+		dev_err(dev, "Unable to request node %d\n", aperture->node_id);
+		goto put_aperture_dev;
+	}
+
+	of_node_get(nc);
+
+	dev_info(dev,
+		 "AI engine aperture %s, id 0x%x, cols(%u, %u) aie_tile_rows(%u, %u) memory_tile_rows(%u, %u) is probed successfully.\n",
+		 dev_name(dev), aperture->node_id,
+		 aperture->range.start.col, aperture->range.size.col,
+		 adev->ttype_attr[AIE_TILE_TYPE_TILE].start_row,
+		 adev->ttype_attr[AIE_TILE_TYPE_TILE].num_rows,
+		 adev->ttype_attr[AIE_TILE_TYPE_MEMORY].start_row,
+		 adev->ttype_attr[AIE_TILE_TYPE_MEMORY].num_rows);
+
+	return aperture;
+
+put_aperture_dev:
+	put_device(dev);
+	return ERR_PTR(ret);
+
+free_aperture:
+	kfree(aperture);
+	return ERR_PTR(ret);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-clock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-clock.c
@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include "ai-engine-internal.h"
+#include <linux/export.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/xlnx-ai-engine.h>
+
+/**
+ * aie_part_get_clk_state_bit() - return bit position of the clock state of a
+ *				  tile
+ * @apart: AI engine partition
+ * @loc: AI engine tile location
+ * @return: bit position for success, negative value for failure
+ */
+static int aie_part_get_clk_state_bit(struct aie_partition *apart,
+				      struct aie_location *loc)
+{
+	if (apart->adev->ops->get_tile_type(apart->adev, loc) !=
+			AIE_TILE_TYPE_TILE)
+		return -EINVAL;
+
+	return (loc->col - apart->range.start.col) *
+	       (apart->range.size.row - 1) + loc->row - 1;
+}
+
+/**
+ * aie_part_scan_clk_state() - scan the clock states of tiles of the AI engine
+ *			       partition
+ * @apart: AI engine partition
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will scan the clock status of both the memory and core
+ * modules.
+ */
+int aie_part_scan_clk_state(struct aie_partition *apart)
+{
+	return apart->adev->ops->scan_part_clocks(apart);
+}
+
+/**
+ * aie_part_check_clk_enable_loc() - return if clock of a tile is enabled
+ * @apart: AI engine partition
+ * @loc: AI engine tile location
+ * @return: true for enabled, false for disabled
+ */
+bool aie_part_check_clk_enable_loc(struct aie_partition *apart,
+				   struct aie_location *loc)
+{
+	int bit;
+
+	if (apart->adev->ops->get_tile_type(apart->adev, loc) !=
+			AIE_TILE_TYPE_TILE)
+		return true;
+
+	bit = aie_part_get_clk_state_bit(apart, loc);
+	return aie_resource_testbit(&apart->cores_clk_state, bit);
+}
+
+/**
+ * aie_part_request_tiles() - request tiles from an AI engine partition.
+ * @apart: AI engine partition
+ * @num_tiles: number of tiles to request. If it is 0, it means all tiles
+ * @locs: the AI engine tiles locations array which will be requested
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will enable clocks of the specified tiles.
+ */
+static int aie_part_request_tiles(struct aie_partition *apart, int num_tiles,
+				  struct aie_location *locs)
+{
+	if (num_tiles == 0) {
+		aie_resource_set(&apart->tiles_inuse, 0,
+				 apart->tiles_inuse.total);
+	} else {
+		u32 n;
+
+		if (!locs)
+			return -EINVAL;
+
+		for (n = 0; n < num_tiles; n++) {
+			int bit = aie_part_get_clk_state_bit(apart, &locs[n]);
+
+			if (bit >= 0)
+				aie_resource_set(&apart->tiles_inuse, bit, 1);
+		}
+	}
+
+	return apart->adev->ops->set_part_clocks(apart);
+}
+
+/**
+ * aie_part_release_tiles() - release tiles from an AI engine partition.
+ * @apart: AI engine partition
+ * @num_tiles: number of tiles to release. If it is 0, it means all tiles
+ * @locs: the AI engine tiles locations array which will be released
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will disable clocks of the specified tiles.
+ */
+static int aie_part_release_tiles(struct aie_partition *apart, int num_tiles,
+				  struct aie_location *locs)
+{
+	if (num_tiles == 0) {
+		aie_resource_clear(&apart->tiles_inuse, 0,
+				   apart->tiles_inuse.total);
+	} else {
+		u32 n;
+
+		if (!locs)
+			return -EINVAL;
+
+		for (n = 0; n < num_tiles; n++) {
+			int bit = aie_part_get_clk_state_bit(apart, &locs[n]);
+
+			if (bit >= 0)
+				aie_resource_clear(&apart->tiles_inuse, bit, 1);
+		}
+	}
+
+	return apart->adev->ops->set_part_clocks(apart);
+}
+
+/**
+ * aie_part_request_tiles_from_user() - request tiles from an AI engine
+ *					partition from user
+ * @apart: AI engine partition
+ * @user_args: user AI engine request tiles argument
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will request tiles from user request.
+ */
+int aie_part_request_tiles_from_user(struct aie_partition *apart,
+				     void __user *user_args)
+{
+	struct aie_tiles_array args;
+	struct aie_location *locs = NULL;
+	int ret;
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	if (args.num_tiles) {
+		u32 i;
+
+		locs = kmalloc_array(args.num_tiles, sizeof(*locs),
+				     GFP_KERNEL);
+		if (!locs)
+			return -ENOMEM;
+
+		if (copy_from_user(locs, (void __user *)args.locs,
+				   args.num_tiles * sizeof(*locs))) {
+			kfree(locs);
+			return -EFAULT;
+		}
+
+		/* update the location to absolute location */
+		for (i = 0; i < args.num_tiles; i++) {
+			if (locs[i].col > apart->range.size.col ||
+			    locs[i].row > apart->range.size.row) {
+				dev_err(&apart->dev,
+					"failed to request tiles, invalid tile(%u,%u).\n",
+					locs[i].col, locs[i].row);
+				kfree(locs);
+				return -EINVAL;
+			}
+			locs[i].col += apart->range.start.col;
+			locs[i].row += apart->range.start.row;
+		}
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(locs);
+		return ret;
+	}
+
+	ret = aie_part_request_tiles(apart, args.num_tiles, locs);
+	mutex_unlock(&apart->mlock);
+
+	kfree(locs);
+	return ret;
+}
+
+/**
+ * aie_part_release_tiles_from_user() - release tiles from an AI engine
+ *					partition from user
+ * @apart: AI engine partition
+ * @user_args: user AI engine request tiles argument
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will release tiles from user request.
+ */
+int aie_part_release_tiles_from_user(struct aie_partition *apart,
+				     void __user *user_args)
+{
+	struct aie_tiles_array args;
+	struct aie_location *locs = NULL;
+	int ret;
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	if (args.num_tiles) {
+		int i;
+
+		locs = kmalloc_array(args.num_tiles, sizeof(*locs),
+				     GFP_KERNEL);
+		if (!locs)
+			return -ENOMEM;
+
+		if (copy_from_user(locs, (void __user *)args.locs,
+				   args.num_tiles * sizeof(*locs))) {
+			kfree(locs);
+			return -EFAULT;
+		}
+
+		/* update the location to absolute location */
+		for (i = 0; i < args.num_tiles; i++) {
+			if (locs[i].col > apart->range.size.col ||
+			    locs[i].row > apart->range.size.row) {
+				dev_err(&apart->dev,
+					"failed to release tiles, invalid tile(%u,%u).\n",
+					locs[i].col, locs[i].row);
+				kfree(locs);
+				return -EINVAL;
+			}
+			locs[i].col += apart->range.start.col;
+			locs[i].row += apart->range.start.row;
+		}
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(locs);
+		return ret;
+	}
+
+	ret = aie_part_release_tiles(apart, args.num_tiles, locs);
+	mutex_unlock(&apart->mlock);
+
+	kfree(locs);
+	return ret;
+}
+
+/**
+ * aie_aperture_get_freq_req() - get current required frequency of aperture
+ * @aperture: AI engine aperture
+ * @return: required clock frequency of the aperture which is the largest
+ *	    required clock frequency of all partitions of the aperture. If
+ *	    return value is 0, it means no partition has specific frequency
+ *	    requirement.
+ */
+static unsigned long aie_aperture_get_freq_req(struct aie_aperture *aperture)
+{
+	struct aie_partition *apart;
+	unsigned long freq_req = 0;
+	int ret;
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret)
+		return freq_req;
+
+	list_for_each_entry(apart, &aperture->partitions, node) {
+		if (apart->freq_req > freq_req)
+			freq_req = apart->freq_req;
+	}
+
+	mutex_unlock(&aperture->mlock);
+
+	return freq_req;
+}
+
+/**
+ * aie_part_set_freq() - set frequency requirement of an AI engine partition
+ *
+ * @apart: AI engine partition
+ * @freq: required frequency
+ * @return: 0 for success, negative value for failure
+ *
+ * This function sets frequency requirement for the partition.
+ * It will call aie_dev_set_freq() to check the frequency requirements
+ * of all partitions. it will send QoS EEMI request to request the max
+ * frequency of all the partitions.
+ */
+int aie_part_set_freq(struct aie_partition *apart, u64 freq)
+{
+	struct aie_device *adev = apart->adev;
+	struct aie_aperture *aperture = apart->aperture;
+	unsigned long clk_rate;
+	u64 temp_freq;
+	u32 boot_qos, current_qos, target_qos;
+	int ret;
+
+	clk_rate = clk_get_rate(adev->clk);
+	if (freq > (u64)clk_rate) {
+		dev_err(&apart->dev,
+			"Invalid frequency to set, larger than full frequency(%lu).\n",
+			clk_rate);
+		return -EINVAL;
+	}
+
+	temp_freq = apart->freq_req;
+	apart->freq_req = freq;
+
+	freq = aie_aperture_get_freq_req(aperture);
+	if (!freq)
+		return 0;
+
+	ret = zynqmp_pm_get_qos(aperture->node_id, &boot_qos, &current_qos);
+	if (ret < 0) {
+		dev_err(&apart->dev, "Failed to get clock divider value.\n");
+		return -EINVAL;
+	}
+
+	target_qos = (boot_qos * clk_rate) / freq;
+
+	/* The clock divisor value (QoS) is a 10-bit value */
+	if (target_qos > (BIT(10) - 1)) {
+		/*
+		 * Reset the logged partition frequency requirement to its
+		 * pervious value.
+		 */
+		apart->freq_req = temp_freq;
+		dev_err(&apart->dev, "Failed to set frequency requirement. Frequency value out-of bound.\n");
+		return -EINVAL;
+	}
+
+	ret = zynqmp_pm_set_requirement(aperture->node_id,
+					ZYNQMP_PM_CAPABILITY_ACCESS, target_qos,
+					ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+	if (ret < 0) {
+		apart->freq_req = temp_freq;
+		dev_err(&apart->dev, "Failed to set frequency requirement.\n");
+	}
+
+	return ret;
+}
+
+/**
+ * aie_partition_set_freq_req() - set partition frequency requirement
+ *
+ * @dev: AI engine partition device
+ * @freq: required frequency
+ * @return: 0 for success, negative value for failure
+ *
+ * This function sets the minimum required frequency for the AI engine
+ * partition. If there are other partitions requiring a higher frequency in the
+ * system, AI engine device will be clocked at that value to satisfy frequency
+ * requirements of all partitions.
+ */
+int aie_partition_set_freq_req(struct device *dev, u64 freq)
+{
+	struct aie_partition *apart;
+
+	if (!dev)
+		return -EINVAL;
+
+	apart = dev_to_aiepart(dev);
+	return aie_part_set_freq(apart, freq);
+}
+EXPORT_SYMBOL_GPL(aie_partition_set_freq_req);
+
+/**
+ * aie_part_get_freq() - get running frequency of AI engine device.
+ *
+ * @apart: AI engine partition
+ * @freq: return running frequency
+ * @return: 0 for success, negative value for failure
+ *
+ * This function gets clock divider value with EEMI requests, and it gets the
+ * full clock frequency from common clock framework. And then it divides the
+ * full clock frequency by the divider value and returns the result.
+ */
+int aie_part_get_freq(struct aie_partition *apart, u64 *freq)
+{
+	unsigned long clk_rate;
+	struct aie_device *adev = apart->adev;
+	u32 boot_qos, current_qos;
+	int ret;
+
+	if (!freq)
+		return -EINVAL;
+
+	clk_rate = clk_get_rate(adev->clk);
+	ret = zynqmp_pm_get_qos(apart->aperture->node_id, &boot_qos,
+				&current_qos);
+	if (ret < 0) {
+		dev_err(&apart->dev, "Failed to get clock divider value.\n");
+		return ret;
+	}
+
+	*freq = (clk_rate * boot_qos) / current_qos;
+	return 0;
+}
+
+/**
+ * aie_partition_get_freq() - get partition running frequency
+ *
+ * @dev: AI engine partition device
+ * @freq: return running frequency
+ * @return: 0 for success, negative value for failure
+ */
+int aie_partition_get_freq(struct device *dev, u64 *freq)
+{
+	struct aie_partition *apart;
+
+	if (!dev)
+		return -EINVAL;
+
+	apart = dev_to_aiepart(dev);
+	return aie_part_get_freq(apart, freq);
+}
+EXPORT_SYMBOL_GPL(aie_partition_get_freq);
+
+/**
+ * aie_partition_get_freq_req() - get partition required frequency
+ *
+ * @dev: AI engine partition device
+ * @freq: return partition required frequency. 0 means partition doesn't
+ *	  have frequency requirement.
+ * @return: 0 for success, negative value for failure
+ */
+int aie_partition_get_freq_req(struct device *dev, u64 *freq)
+{
+	struct aie_partition *apart;
+
+	if (!dev)
+		return -EINVAL;
+
+	apart = dev_to_aiepart(dev);
+	*freq = apart->freq_req;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(aie_partition_get_freq_req);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-dev-v1_0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-dev-v1_0.c
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/anon_inodes.h>
+#include <linux/cdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/file.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/fs.h>
+#include <linux/idr.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+#define VERSAL_SILICON_REV_MASK		GENMASK(31, 28)
+
+/**
+ * xilinx_ai_engine_probe_v1() - probe device tree v1.0 AI engine device
+ * @pdev: AI engine platform device
+ * @return: 0 for success, negative value for failure
+ */
+int xilinx_ai_engine_probe_v1(struct platform_device *pdev)
+{
+	struct aie_device *adev;
+	struct aie_aperture *aperture;
+	struct aie_range *range;
+	struct device *dev;
+	struct device_node *nc;
+	struct resource *res;
+	u32 idcode, version, pm_reg[2], regs[4];
+	int ret;
+
+	dev_info(&pdev->dev, "probing xlnx,ai-engine-v1.0 device.\n");
+
+	adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL);
+	if (!adev)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, adev);
+	INIT_LIST_HEAD(&adev->apertures);
+	mutex_init(&adev->mlock);
+
+	/* Initialize AIE device specific instance. */
+	ret = aie_device_init(adev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to initialize device instance.\n");
+		return ret;
+	}
+
+	/*
+	 * AI Engine platform management node ID is required for requesting
+	 * services from firmware driver.
+	 */
+	ret = of_property_read_u32_array(pdev->dev.of_node, "power-domains",
+					 pm_reg, ARRAY_SIZE(pm_reg));
+	if (ret < 0) {
+		dev_err(&pdev->dev,
+			"Failed to read power manangement information\n");
+		return ret;
+	}
+	adev->pm_node_id = pm_reg[1];
+
+	ret = zynqmp_pm_get_chipid(&idcode, &version);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Failed to get chip ID\n");
+		return ret;
+	}
+	adev->version = FIELD_GET(VERSAL_SILICON_REV_MASK, idcode);
+
+	adev->clk = devm_clk_get(&pdev->dev, NULL);
+	if (!adev->clk) {
+		dev_err(&pdev->dev, "Failed to get device clock.\n");
+		return -EINVAL;
+	}
+
+	ret = xilinx_ai_engine_add_dev(adev, pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to add AI engine device.\n");
+		return ret;
+	}
+
+	/* v1 support single aperture only */
+	nc = of_get_next_child(pdev->dev.of_node, NULL);
+	if (!nc) {
+		dev_err(&pdev->dev,
+			"device tree node v1.0, no child node.\n");
+		put_device(dev);
+		return -EINVAL;
+	}
+
+	aperture = kzalloc(sizeof(*aperture), GFP_KERNEL);
+	if (!aperture) {
+		put_device(dev);
+		return -ENOMEM;
+	}
+
+	aperture->adev = adev;
+	INIT_LIST_HEAD(&aperture->partitions);
+	mutex_init(&aperture->mlock);
+
+	ret = of_property_read_u32_array(nc, "reg", regs,
+					 ARRAY_SIZE(regs));
+	if (ret < 0) {
+		dev_err(&adev->dev,
+			"probe %pOF failed, no tiles range information.\n",
+			nc);
+		kfree(aperture);
+		put_device(dev);
+		return ret;
+	}
+	range = &aperture->range;
+	range->start.col = regs[0] & aligned_byte_mask(1);
+	range->size.col = regs[2] & aligned_byte_mask(1);
+	range->start.row = 0;
+	range->size.row = adev->ttype_attr[AIE_TILE_TYPE_SHIMPL].num_rows +
+			  adev->ttype_attr[AIE_TILE_TYPE_TILE].num_rows;
+
+	/* register device for aperture */
+	ret = aie_aperture_add_dev(aperture, nc);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to add AI engine aperture device\n");
+		kfree(aperture);
+		put_device(dev);
+		return ret;
+	}
+
+	/**
+	 * Initialize columns resource map to remember which columns have been
+	 * assigned. Used for partition management.
+	 */
+	ret = aie_resource_initialize(&aperture->cols_res,
+				      aperture->range.size.col);
+	if (ret) {
+		dev_err(dev, "failed to initialize columns resource.\n");
+		put_device(dev);
+		return ret;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "No memory resource.\n");
+		put_device(&aperture->dev);
+		put_device(dev);
+		return -EINVAL;
+	}
+	/* resource information will be used by ready only register mmap */
+	memcpy(&aperture->res, res, sizeof(*res));
+	aperture->base = devm_ioremap_resource(&aperture->dev, &aperture->res);
+	if (IS_ERR(aperture->base)) {
+		dev_err(&pdev->dev, "no io memory resource.\n");
+		ret = PTR_ERR(aperture->base);
+		put_device(&aperture->dev);
+		put_device(dev);
+		return ret;
+	}
+
+	/* Get device node DMA setting */
+	aperture->dev.coherent_dma_mask = DMA_BIT_MASK(48);
+	aperture->dev.dma_mask = &aperture->dev.coherent_dma_mask;
+	ret = of_dma_configure(&aperture->dev, nc, true);
+	if (ret)
+		dev_warn(&aperture->dev, "Failed to configure DMA.\n");
+
+	INIT_WORK(&aperture->backtrack, aie_aperture_backtrack);
+	ret = aie_aperture_create_l2_bitmap(aperture);
+	if (ret) {
+		dev_err(&aperture->dev,
+			"failed to initialize l2 mask resource.\n");
+		put_device(&aperture->dev);
+		put_device(dev);
+		return ret;
+	}
+
+	ret = platform_get_irq_byname(pdev, "interrupt1");
+	if (ret < 0) {
+		put_device(&aperture->dev);
+		put_device(dev);
+		return ret;
+	}
+	aperture->irq = ret;
+
+	ret = devm_request_threaded_irq(&aperture->dev, aperture->irq, NULL,
+					aie_interrupt, IRQF_ONESHOT,
+					dev_name(&aperture->dev), aperture);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to request AIE IRQ.\n");
+		put_device(&aperture->dev);
+		put_device(dev);
+		return ret;
+	}
+
+	of_node_get(nc);
+
+	list_add_tail(&aperture->node, &adev->apertures);
+
+	dev_info(&pdev->dev, "ai-enginee-v1.0 device node is probed.\n");
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-dev.c
@@ -0,0 +1,852 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/anon_inodes.h>
+#include <linux/cdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/file.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/fs.h>
+#include <linux/idr.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/xlnx-ai-engine.h>
+#include <uapi/linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+#define AIE_DEV_MAX			(MINORMASK + 1)
+#define VERSAL_SILICON_REV_MASK		GENMASK(31, 28)
+
+static dev_t aie_major;
+struct class *aie_class;
+
+static DEFINE_IDA(aie_device_ida);
+static DEFINE_IDA(aie_minor_ida);
+
+/**
+ * aie_partition_fd() - returns a file descriptor for the given AI engine
+ *			partition device
+ * @apart: AI engine partition
+ * @return: file descriptor of the AI engine partition for success,
+ *	    negative value for failure.
+ *
+ * This function allocate a file descriptor for the AI engine partition
+ * export file.
+ */
+static int aie_partition_fd(struct aie_partition *apart)
+{
+	int ret;
+
+	ret = get_unused_fd_flags(O_CLOEXEC);
+	if (ret < 0) {
+		dev_err(&apart->dev,
+			"Failed to get fd for partition %u.\n",
+			apart->partition_id);
+		return ret;
+	}
+	fd_install(ret, apart->filep);
+
+	return ret;
+}
+
+/**
+ * aie_enquire_partitions() - get AI engine partitions information
+ * @adev: AI engine device
+ * @query: data struct to store the partition information
+ * @return: 0 for success, and negative value for failure.
+ */
+static int aie_enquire_partitions(struct aie_device *adev,
+				  struct aie_partition_query *query)
+{
+	struct aie_aperture *aperture;
+	struct aie_range_args *query_parts;
+	u32 part_cnt, parts_filled;
+	int ret;
+
+	if (!query->partitions) {
+		part_cnt = 0;
+
+		/*
+		 * If partitions information buffer is NULL.
+		 * It is to get the number of partitions.
+		 */
+		ret = mutex_lock_interruptible(&adev->mlock);
+		if (ret)
+			return ret;
+
+		list_for_each_entry(aperture, &adev->apertures, node) {
+			part_cnt += aie_aperture_get_num_parts(aperture);
+		}
+		mutex_unlock(&adev->mlock);
+
+		query->partition_cnt = part_cnt;
+
+		return 0;
+	}
+
+	part_cnt = query->partition_cnt;
+	if (!part_cnt)
+		return 0;
+	parts_filled = 0;
+	query_parts = query->partitions;
+
+	ret = mutex_lock_interruptible(&adev->mlock);
+	if (ret)
+		return ret;
+
+	list_for_each_entry(aperture, &adev->apertures, node) {
+		int lparts_filled, num_parts_left;
+
+		lparts_filled = aie_aperture_enquire_parts(aperture,
+							   part_cnt,
+							   query_parts,
+							   &num_parts_left,
+							   true);
+		if (lparts_filled < 0) {
+			dev_err(&adev->dev,
+				"failed to enquire partitions.\n");
+			mutex_unlock(&adev->mlock);
+			return lparts_filled;
+		}
+		parts_filled += lparts_filled;
+		query_parts += lparts_filled;
+		/*
+		 * input partitions enquires buffers are less than the number
+		 * of partitions.
+		 * TODO: ioctl arguments can be updated to include how many
+		 * number of partitions information not yet filled.
+		 */
+		if (num_parts_left)
+			break;
+	}
+	mutex_unlock(&adev->mlock);
+	query->partition_cnt = parts_filled;
+
+	return 0;
+}
+
+/**
+ * aie_request_part_from_id() - request AI engine partition from id
+ * @adev: AI engine device
+ * @partition_id: partition id to check
+ * @return: partition pointer for success, and NULL for failure
+ *
+ * The partition ID contains the start column and number of columns
+ * information for the partition.
+ * This function expect the caller to lock mlock of @adev.
+ */
+static struct aie_partition *aie_request_part_from_id(struct aie_device *adev,
+						      u32 partition_id)
+{
+	struct aie_aperture *aperture;
+
+	list_for_each_entry(aperture, &adev->apertures, node) {
+		struct aie_partition *apart;
+
+		apart = aie_aperture_request_part_from_id(aperture,
+							  partition_id);
+		if (apart)
+			return apart;
+	}
+
+	return ERR_PTR(-EINVAL);
+}
+
+/**
+ * aie_partition_get() - Request the specified AI engine partition
+ *
+ * @apart: AI engine partition
+ * @req: AI engine partition request information which includes image UID.
+ *	 flag to indicate if the partition will cleanup or not when releasing
+ *	 the partition.
+ * @return: 0 for success, and negative value for failure.
+ *
+ * This function will check if the specified partition can be requested, it
+ * will check if the partition has been loaded with an image, if no, as long
+ * as it is not in use, the partition request will be granted. If there is
+ * image loaded, it will check if the given UID from @req matches the image UID
+ * loaded on the partition, if they match, the partition request will be
+ * granted. A file will be created for the requested partition.
+ */
+static int aie_partition_get(struct aie_partition *apart,
+			     struct aie_partition_req *req)
+{
+	struct file *filep;
+	int ret;
+
+	(void)req;
+
+	if (apart->status == XAIE_PART_STATUS_INUSE) {
+		dev_err(&apart->dev,
+			"request partition %u failed, partition in use.\n",
+			apart->partition_id);
+		return -EBUSY;
+	}
+	/*
+	 * TODO:
+	 * 1. It will check image UID too to see if the user matches what's
+	 *    loaded in the AI engine partition. And check the meta data to see
+	 *    which resources used by application.
+	 */
+
+	/* Get a file for the partition */
+	filep = anon_inode_getfile(dev_name(&apart->dev), &aie_part_fops,
+				   apart, O_RDWR);
+	if (IS_ERR(filep)) {
+		dev_err(&apart->dev,
+			"Failed to request partition %u, failed to get file.\n",
+			apart->partition_id);
+		return PTR_ERR(filep);
+	}
+
+	filep->f_mode |= (FMODE_LSEEK | FMODE_PREAD | FMODE_PWRITE);
+	apart->filep = filep;
+
+	apart->cntrflag = req->flag;
+
+	/* open AI engine partition instance to get it ready for use */
+	ret = aie_part_open(apart, (void *)req->meta_data);
+	if (ret) {
+		dev_err(&apart->dev, "Failed to open partition %u instance.\n",
+			apart->partition_id);
+		fput(filep);
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * aie_partition_request_from_adev() - request AI engine partition from AI
+ *				       engine device
+ * @adev: AI engine device
+ * @req: partition request, includes the requested AI engine information
+ *	 such as partition node ID and the UID of the image which is used
+ *	 to describe the partition to request.
+ * @return: pointer to the AI engine partition for success, and negative
+ *	    value for failure.
+ *
+ * This function finds a defined partition which matches the specified
+ * partition id, and request it.
+ */
+static struct aie_partition *
+aie_partition_request_from_adev(struct aie_device *adev,
+				struct aie_partition_req *req)
+{
+	struct aie_partition *apart;
+	int ret;
+
+	ret = mutex_lock_interruptible(&adev->mlock);
+	if (ret)
+		return ERR_PTR(ret);
+
+	apart = aie_request_part_from_id(adev, req->partition_id);
+	if (IS_ERR(apart)) {
+		dev_err(&adev->dev,
+			"request partition %u failed, not exist.\n",
+			req->partition_id);
+		mutex_unlock(&adev->mlock);
+		return ERR_PTR(-EINVAL);
+	}
+	mutex_unlock(&adev->mlock);
+
+	ret = aie_partition_get(apart, req);
+
+	if (ret)
+		apart = ERR_PTR(ret);
+	return apart;
+}
+
+static long xilinx_ai_engine_ioctl(struct file *filp, unsigned int cmd,
+				   unsigned long arg)
+{
+	struct inode *inode = file_inode(filp);
+	struct aie_device *adev = cdev_to_aiedev(inode->i_cdev);
+	void __user *argp = (void __user *)arg;
+	int ret;
+
+	switch (cmd) {
+	case AIE_ENQUIRE_PART_IOCTL:
+	{
+		struct aie_partition_query query;
+		struct aie_partition_query  __user *uquery_ptr = argp;
+
+		if (copy_from_user(&query, uquery_ptr, sizeof(query)))
+			return -EFAULT;
+		ret = aie_enquire_partitions(adev, &query);
+		if (ret < 0)
+			return ret;
+		if (copy_to_user((void __user *)&uquery_ptr->partition_cnt,
+				 &query.partition_cnt,
+				 sizeof(query.partition_cnt)))
+			return -EFAULT;
+		break;
+	}
+	case AIE_REQUEST_PART_IOCTL:
+	{
+		struct aie_partition_req req;
+		struct aie_partition *apart;
+
+		if (copy_from_user(&req, argp, sizeof(req)))
+			return -EFAULT;
+
+		apart = aie_partition_request_from_adev(adev, &req);
+		if (IS_ERR(apart))
+			return PTR_ERR(apart);
+
+		/* Allocate fd */
+		ret = aie_partition_fd(apart);
+		if (ret < 0) {
+			fput(apart->filep);
+			break;
+		}
+		break;
+	}
+	default:
+		dev_err(&adev->dev, "Invalid ioctl command %u.\n", cmd);
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+static const struct file_operations aie_device_fops = {
+	.owner		= THIS_MODULE,
+	.unlocked_ioctl	= xilinx_ai_engine_ioctl,
+};
+
+static void xilinx_ai_engine_release_device(struct device *dev)
+{
+	struct aie_device *adev = dev_to_aiedev(dev);
+
+	ida_simple_remove(&aie_device_ida, dev->id);
+	ida_simple_remove(&aie_minor_ida, MINOR(dev->devt));
+	cdev_del(&adev->cdev);
+}
+
+/**
+ * of_xilinx_ai_engine_aperture_probe() - probes AI engine aperture nodes
+ * @adev: AI engine device
+ *
+ * This function will probe children AI engine apertures nodes and create
+ * an AI engine aperture instance for each node.
+ */
+void of_xilinx_ai_engine_aperture_probe(struct aie_device *adev)
+{
+	struct device_node *nc;
+
+	for_each_available_child_of_node(adev->dev.of_node, nc) {
+		struct aie_aperture *aperture;
+		int ret;
+
+		if (of_node_test_and_set_flag(nc, OF_POPULATED))
+			continue;
+
+		ret = mutex_lock_interruptible(&adev->mlock);
+		if (ret)
+			return;
+
+		aperture = of_aie_aperture_probe(adev, nc);
+		if (IS_ERR(aperture)) {
+			dev_err(&adev->dev,
+				"Failed to probe AI engine aperture for %pOF\n",
+				nc);
+			/* try to probe the next node */
+			continue;
+		}
+		list_add_tail(&aperture->node, &adev->apertures);
+
+		mutex_unlock(&adev->mlock);
+	}
+}
+
+/**
+ * xilinx_ai_engine_add_dev() - initialize and add AI engine device
+ * @adev: AI engine device
+ * @pdev: AI engine platform device
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will initialize and add AI engine device to Linux kernel
+ * device framework.
+ * TODO: This function should be moved back to xilinx_ai_engine_probe()
+ * implementation once v1.0 device node support is removed.
+ */
+int xilinx_ai_engine_add_dev(struct aie_device *adev,
+			     struct platform_device *pdev)
+{
+	struct device *dev;
+	int ret;
+
+	dev = &adev->dev;
+	device_initialize(dev);
+	dev->class = aie_class;
+	dev->parent = &pdev->dev;
+	dev->of_node = pdev->dev.of_node;
+
+	ret = ida_simple_get(&aie_minor_ida, 0, AIE_DEV_MAX, GFP_KERNEL);
+	if (ret < 0)
+		return ret;
+	dev->devt = MKDEV(MAJOR(aie_major), ret);
+	ret = ida_simple_get(&aie_device_ida, 0, 0, GFP_KERNEL);
+	if (ret < 0) {
+		ida_simple_remove(&aie_minor_ida, MINOR(dev->devt));
+		return ret;
+	}
+	dev->id = ret;
+	dev_set_name(&adev->dev, "aie%d", dev->id);
+
+	cdev_init(&adev->cdev, &aie_device_fops);
+	adev->cdev.owner = THIS_MODULE;
+	ret = cdev_add(&adev->cdev, dev->devt, 1);
+	if (ret) {
+		ida_simple_remove(&aie_device_ida, dev->id);
+		ida_simple_remove(&aie_minor_ida, MINOR(dev->devt));
+		return ret;
+	}
+	/* We can now rely on the release function for cleanup */
+	dev->release = xilinx_ai_engine_release_device;
+
+	ret = device_add(dev);
+	if (ret) {
+		dev_err(&pdev->dev, "device_add failed: %d\n", ret);
+		put_device(dev);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xilinx_ai_engine_probe(struct platform_device *pdev)
+{
+	struct aie_device *adev;
+	u32 idcode, version, pm_reg[2];
+	int ret;
+	u8 regs_u8[2];
+	u8 aie_gen;
+
+	adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL);
+	if (!adev)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, adev);
+	INIT_LIST_HEAD(&adev->apertures);
+	mutex_init(&adev->mlock);
+
+	/* check if device node is v1.0 or not */
+	ret = of_device_is_compatible(pdev->dev.of_node, "xlnx,ai-engine-v1.0");
+	if (ret)
+		return xilinx_ai_engine_probe_v1(pdev);
+
+	ret = of_property_read_u8(pdev->dev.of_node, "xlnx,aie-gen", &aie_gen);
+	if (ret < 0) {
+		dev_warn(&pdev->dev,
+			 "no aie dev generation information in device tree\n");
+		return ret;
+	}
+
+	ret = of_property_read_u8_array(pdev->dev.of_node, "xlnx,shim-rows",
+					regs_u8, ARRAY_SIZE(regs_u8));
+	if (ret < 0) {
+		dev_warn(&pdev->dev,
+			 "no SHIM rows information in device tree\n");
+		return ret;
+	}
+	adev->ttype_attr[AIE_TILE_TYPE_SHIMPL].start_row = regs_u8[0];
+	adev->ttype_attr[AIE_TILE_TYPE_SHIMPL].num_rows = regs_u8[1];
+	adev->ttype_attr[AIE_TILE_TYPE_SHIMNOC].start_row = regs_u8[0];
+	adev->ttype_attr[AIE_TILE_TYPE_SHIMNOC].num_rows = regs_u8[1];
+
+	ret = of_property_read_u8_array(pdev->dev.of_node, "xlnx,core-rows",
+					regs_u8, ARRAY_SIZE(regs_u8));
+	if (ret < 0) {
+		dev_err(&pdev->dev,
+			"Failed to read core rows information\n");
+		return ret;
+	}
+	adev->ttype_attr[AIE_TILE_TYPE_TILE].start_row = regs_u8[0];
+	adev->ttype_attr[AIE_TILE_TYPE_TILE].num_rows = regs_u8[1];
+
+	ret = of_property_read_u8_array(pdev->dev.of_node, "xlnx,mem-rows",
+					regs_u8, ARRAY_SIZE(regs_u8));
+	if (ret < 0) {
+		dev_err(&pdev->dev,
+			"Failed to read mem rows information\n");
+		return ret;
+	}
+
+	adev->ttype_attr[AIE_TILE_TYPE_MEMORY].start_row = regs_u8[0];
+	adev->ttype_attr[AIE_TILE_TYPE_MEMORY].num_rows = regs_u8[1];
+
+	adev->dev_gen = aie_gen;
+	if (aie_gen == AIE_DEVICE_GEN_AIE) {
+		ret = aie_device_init(adev);
+	} else if (aie_gen == AIE_DEVICE_GEN_AIEML) {
+		ret = aieml_device_init(adev);
+	} else {
+		dev_err(&pdev->dev, "Invalid device generation\n");
+		return -EINVAL;
+	}
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to initialize device instance.\n");
+		return ret;
+	}
+
+	/*
+	 * AI Engine platform management node ID is required for requesting
+	 * services from firmware driver.
+	 */
+	ret = of_property_read_u32_array(pdev->dev.of_node, "power-domains",
+					 pm_reg, ARRAY_SIZE(pm_reg));
+	if (ret < 0) {
+		dev_err(&pdev->dev,
+			"Failed to read power manangement information\n");
+		return ret;
+	}
+	adev->pm_node_id = pm_reg[1];
+
+	ret = zynqmp_pm_get_chipid(&idcode, &version);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Failed to get chip ID\n");
+		return ret;
+	}
+	adev->version = FIELD_GET(VERSAL_SILICON_REV_MASK, idcode);
+
+	adev->clk = devm_clk_get(&pdev->dev, "aclk0");
+	if (!adev->clk) {
+		dev_err(&pdev->dev, "Failed to get device clock.\n");
+		return -EINVAL;
+	}
+
+	ret = xilinx_ai_engine_add_dev(adev, pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to add ai engine device.\n");
+		return ret;
+	}
+
+	of_xilinx_ai_engine_aperture_probe(adev);
+	dev_info(&pdev->dev,
+		 "Xilinx AI Engine device %s probed. Device generation: %u. Clock frequency: %ldHz.\n",
+		 dev_name(&pdev->dev), aie_gen, clk_get_rate(adev->clk));
+
+	return 0;
+}
+
+static int xilinx_ai_engine_remove(struct platform_device *pdev)
+{
+	struct aie_device *adev = platform_get_drvdata(pdev);
+	struct list_head *node, *pos;
+
+	list_for_each_safe(pos, node, &adev->apertures) {
+		struct aie_aperture *aperture;
+		int ret;
+
+		aperture = list_entry(pos, struct aie_aperture, node);
+		ret = aie_aperture_remove(aperture);
+		if (ret)
+			return ret;
+	}
+
+	device_del(&adev->dev);
+	put_device(&adev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id xilinx_ai_engine_of_match[] = {
+	{ .compatible = "xlnx,ai-engine-v2.0", },
+	{ .compatible = "xlnx,ai-engine-v1.0", },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xilinx_ai_engine_of_match);
+
+static struct platform_driver xilinx_ai_engine_driver = {
+	.probe			= xilinx_ai_engine_probe,
+	.remove			= xilinx_ai_engine_remove,
+	.driver			= {
+		.name		= "xilinx-ai-engine",
+		.of_match_table	= xilinx_ai_engine_of_match,
+	},
+};
+
+/**
+ * of_ai_engine_class_find() - find AI engine device with device node
+ * @np: device node
+ * @return: AI engine device pointer if found, NULL if it is not found
+ *
+ * This function checks every AI engine device of the aie_class, returns the
+ * one whose of_node matches the input of node.
+ */
+struct aie_device *of_ai_engine_class_find(struct device_node *np)
+{
+	struct device *dev;
+
+	dev = class_find_device(aie_class, NULL, np, device_match_of_node);
+	if (!dev)
+		return NULL;
+
+	return dev_to_aiedev(dev);
+}
+
+/**
+ * aie_partition_is_available() - Check if an AI engine partition is available
+ * @req: AI engine partition requesting arguments
+ * @return: true if the AI engine partition is not in use, otherwise, false
+ *
+ * This function looks up the AI engine class devices to find the AI engine
+ * partition whose partition ID matches the given partition ID in @req. If
+ * the partition can be found, if will check if the partition is in use.
+ *
+ * In case the AI engine release function is called from kernel context, the
+ * release() will be scheduled when the AI engine partition reference count is
+ * reduced to 0 instead of get called synchronously, and thus, this is a helper
+ * function for another kernel module to check if the partitions is released
+ * after calling release function from kernel context
+ *
+ * However, if closing the partition is from user context, it will not return
+ * until the release is complete when there is no reference to the AI engine
+ * partition file. In this case, user doesn't need to call this function to
+ * check if the partition is released.
+ */
+bool aie_partition_is_available(struct aie_partition_req *req)
+{
+	struct device *dev;
+	struct class_dev_iter iter;
+
+	if (!req)
+		return false;
+
+	class_dev_iter_init(&iter, aie_class, NULL, NULL);
+	while ((dev = class_dev_iter_next(&iter))) {
+		struct aie_aperture *aperture;
+		int ret;
+
+		if (strncmp(dev_name(dev), "aieaperture",
+			    strlen("aieaperture")))
+			continue;
+
+		aperture = dev_get_drvdata(dev);
+		ret = aie_aperture_check_part_avail(aperture, req);
+		if (ret == XAIE_PART_STATUS_INUSE) {
+			class_dev_iter_exit(&iter);
+			return false;
+		} else if (ret == XAIE_PART_STATUS_IDLE) {
+			class_dev_iter_exit(&iter);
+			return true;
+		}
+
+		continue;
+	}
+	class_dev_iter_exit(&iter);
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(aie_partition_is_available);
+
+/**
+ * aie_partition_request() - Request an AI engine partition
+ * @req: AI engine partition requesting arguments
+ * @return: pointer to the AI engine partition device, error value for failure.
+ *
+ * This function looks up the AI engine class devices to find the AI engine
+ * partition whose partition ID matches the given partition ID in @req. If
+ * the partition can be found, it will try to request it. It will get a file
+ * for the requested AI engine partition. User can only use the AI engine
+ * partition after it is successfully requested.
+ */
+struct device *aie_partition_request(struct aie_partition_req *req)
+{
+	struct aie_partition *apart = NULL;
+	struct device *dev;
+	struct class_dev_iter iter;
+	int ret;
+
+	if (!req)
+		return ERR_PTR(-EINVAL);
+
+	class_dev_iter_init(&iter, aie_class, NULL, NULL);
+	while ((dev = class_dev_iter_next(&iter))) {
+		struct aie_aperture *aperture;
+		int ret;
+
+		if (strncmp(dev_name(dev), "aieaperture",
+			    strlen("aieaperture")))
+			continue;
+
+		aperture = dev_get_drvdata(dev);
+		ret = aie_aperture_check_part_avail(aperture, req);
+		if (ret == XAIE_PART_STATUS_INVALID) {
+			continue;
+		} else if (ret == XAIE_PART_STATUS_INUSE) {
+			class_dev_iter_exit(&iter);
+			dev_err(&aperture->dev,
+				"failed to request partition %u: in use.\n",
+				req->partition_id);
+			return ERR_PTR(-EBUSY);
+		}
+
+		class_dev_iter_exit(&iter);
+
+		apart = aie_aperture_request_part_from_id(aperture,
+							  req->partition_id);
+		if (IS_ERR(apart))
+			return ERR_PTR(PTR_ERR(apart));
+		break;
+	}
+
+	if (!apart) {
+		pr_err("failed to request partition %u: invalid partition.\n",
+		       req->partition_id);
+		return ERR_PTR(-EINVAL);
+	}
+
+	ret = aie_partition_get(apart, req);
+	if (ret) {
+		if (mutex_lock_interruptible(&apart->aperture->mlock))
+			return ERR_PTR(ret);
+
+		list_del(&apart->node);
+		aie_part_remove(apart);
+		mutex_unlock(&apart->aperture->mlock);
+	}
+
+	return &apart->dev;
+}
+EXPORT_SYMBOL_GPL(aie_partition_request);
+
+/**
+ * aie_partition_get_fd() - get AI engine partition file descriptor
+ * @dev: AI engine partition device pointer
+ * @return: file descriptor for the AI engine partition for success, and
+ *	    negative value for failure.
+ *
+ * This function allocate a file descriptor for the AI engine requested
+ * partition, and increase the reference count to the AI engine partition file.
+ */
+int aie_partition_get_fd(struct device *dev)
+{
+	struct aie_partition *apart;
+	int ret;
+
+	if (!dev)
+		return -EINVAL;
+
+	apart = dev_to_aiepart(dev);
+
+	ret = aie_partition_fd(apart);
+	if (ret < 0)
+		return ret;
+
+	get_file(apart->filep);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(aie_partition_get_fd);
+
+/**
+ * aie_partition_release() - Recrease refcount of the AI engine partition
+ * @dev: AI engine partition device
+ */
+void aie_partition_release(struct device *dev)
+{
+	struct aie_partition *apart;
+
+	if (WARN_ON(!dev))
+		return;
+
+	apart = dev_to_aiepart(dev);
+	fput(apart->filep);
+}
+EXPORT_SYMBOL_GPL(aie_partition_release);
+
+/**
+ * aie_partition_reset() - Reset AI engine partition
+ * @dev: AI engine partition device
+ * @return: 0 for success, negative value for failure
+ */
+int aie_partition_reset(struct device *dev)
+{
+	struct aie_partition *apart;
+
+	if (WARN_ON(!dev))
+		return -EINVAL;
+
+	apart = dev_to_aiepart(dev);
+	return aie_part_reset(apart);
+}
+EXPORT_SYMBOL_GPL(aie_partition_reset);
+
+/**
+ * aie_partition_post_reinit() - Indicate AI engine partition driver the
+ *				 partition has been re-initialized.
+ * @dev: AI engine partition device
+ * @return: 0 for success, negative value for failure
+ *
+ * This function is called after the AI engine partition is reconfigured with
+ * PDI outside the AI engine driver.
+ */
+int aie_partition_post_reinit(struct device *dev)
+{
+	struct aie_partition *apart;
+
+	if (WARN_ON(!dev))
+		return -EINVAL;
+
+	apart = dev_to_aiepart(dev);
+	return aie_part_post_reinit(apart);
+}
+EXPORT_SYMBOL_GPL(aie_partition_post_reinit);
+
+static int __init xilinx_ai_engine_init(void)
+{
+	int ret;
+
+	ret = alloc_chrdev_region(&aie_major, 0, AIE_DEV_MAX, "aie");
+	if (ret < 0) {
+		pr_err("aie: failed to allocate aie region\n");
+		return ret;
+	}
+
+	aie_class = class_create(THIS_MODULE, "aie");
+	if (IS_ERR(aie_class)) {
+		pr_err("failed to create aie class\n");
+		unregister_chrdev_region(aie_major, AIE_DEV_MAX);
+		return PTR_ERR(aie_class);
+	}
+
+	ret = aie_overlay_register_notifier();
+	if (ret) {
+		pr_err("aie: failed to register device tree overlay notifier.\n");
+		return ret;
+	}
+
+	platform_driver_register(&xilinx_ai_engine_driver);
+
+	return 0;
+}
+postcore_initcall(xilinx_ai_engine_init);
+
+static void __exit xilinx_ai_engine_exit(void)
+{
+	aie_overlay_unregister_notifier();
+	platform_driver_unregister(&xilinx_ai_engine_driver);
+	class_destroy(aie_class);
+	unregister_chrdev_region(aie_major, AIE_DEV_MAX);
+}
+module_exit(xilinx_ai_engine_exit);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-dma.c
@@ -0,0 +1,668 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine driver DMA implementation
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include "ai-engine-internal.h"
+#include <linux/dma-buf.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/refcount.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+
+/**
+ * struct aie_dmabuf - AI engine dmabuf information
+ * @attach: dmabuf attachment pointer
+ * @sgt: scatter/gather table
+ * @refs: refcount of the attached aie_dmabuf
+ * @node: list node
+ */
+struct aie_dmabuf {
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	refcount_t refs;
+	struct list_head node;
+};
+
+/**
+ * aie_part_find_dmabuf() - find a attached dmabuf
+ * @apart: AI engine partition
+ * @dmabuf: pointer to dmabuf
+ * @return: pointer to AI engine dmabuf struct of the found dmabuf, if dmabuf
+ *	    is not found, returns NULL.
+ *
+ * This function scans all the attached dmabufs to see the input dmabuf is
+ * in the list. if it is attached, return the corresponding struct aie_dmabuf
+ * pointer.
+ */
+static struct aie_dmabuf *
+aie_part_find_dmabuf(struct aie_partition *apart, struct dma_buf *dmabuf)
+{
+	struct aie_dmabuf *adbuf;
+
+	list_for_each_entry(adbuf, &apart->dbufs, node) {
+		if (dmabuf == adbuf->attach->dmabuf)
+			return adbuf;
+	}
+
+	return NULL;
+}
+
+/**
+ * aie_part_find_dmabuf_from_file() - find a attached dmabuf from file
+ * @apart: AI engine partition
+ * @file: file which belongs to a dmabuf
+ * @return: pointer to AI engine dmabuf struct of the found dmabuf, if dmabuf
+ *	    is not found, returns NULL.
+ *
+ * This function scans all the attached dmabufs of the AI engine partition,
+ * it checks the file with the attached dmabufs, if it founds a match, it
+ * returns the aie_dmabuf pointer.
+ */
+static struct aie_dmabuf *
+aie_part_find_dmabuf_from_file(struct aie_partition *apart,
+			       const struct file *file)
+{
+	struct aie_dmabuf *adbuf;
+
+	list_for_each_entry(adbuf, &apart->dbufs, node) {
+		if (file == adbuf->attach->dmabuf->file)
+			return adbuf;
+	}
+
+	return NULL;
+}
+
+/**
+ * aie_part_get_dmabuf_da() -  get DMA address from the va
+ * @apart: AI engine partition
+ * @va: virtual address
+ * @len: memory length
+ * @return: dma address of the specified va, or 0 if va is not valid
+ *
+ * This function returns DMA address if the has been mapped to a dmabuf which
+ * has been attached to the AI engine partition.
+ */
+static dma_addr_t aie_part_get_dmabuf_da(struct aie_partition *apart,
+					 void *va, size_t len)
+{
+	struct vm_area_struct *vma;
+	struct aie_dmabuf *adbuf;
+	unsigned long va_start, va_off;
+
+	va_start = (unsigned long)((uintptr_t)va);
+	if (!current->mm) {
+		dev_err(&apart->dev,
+			"failed to get dma address from va, no process mm.\n");
+		return 0;
+	}
+
+	vma = find_vma(current->mm, va_start);
+	if (!vma) {
+		dev_err(&apart->dev, "failed to find vma for %p, 0x%zx.\n",
+			va, len);
+		return 0;
+	}
+
+	adbuf = aie_part_find_dmabuf_from_file(apart, vma->vm_file);
+	if (!adbuf) {
+		dev_err(&apart->dev,
+			"failed to get dma address for %p, no dma buf is found.\n",
+			va);
+		return 0;
+	}
+
+	va_off = va_start - vma->vm_start;
+	/*
+	 * As we only support continuous DMA memory which is guaranteed from
+	 * dmabuf attachment, we will compared with the size of the dmabuf only
+	 */
+	if (va_off + len >= adbuf->attach->dmabuf->size) {
+		dev_err(&apart->dev,
+			"failed to get dma address for %p, 0x%zx.\n", va, len);
+		return 0;
+	}
+
+	return sg_dma_address(adbuf->sgt->sgl) + va_off;
+}
+
+/**
+ * aie_part_get_dmabuf_da_from_off() - get DMA address from offset to a dmabuf
+ * @apart: AI engine partition
+ * @dmabuf_fd: dmabuf file descriptor
+ * @off: offset to the start of a dmabuf
+ * @len: memory length
+ * @return: dma address, or 0 if @off or @len is invalid, or if @dmabuf_fd is
+ *	    not attached.
+ *
+ * This function returns DMA address if has been mapped to a dmabuf which has
+ * been attached to the AI engine partition.
+ */
+static dma_addr_t
+aie_part_get_dmabuf_da_from_off(struct aie_partition *apart, int dmabuf_fd,
+				u64 off, size_t len)
+{
+	struct dma_buf *dbuf = dma_buf_get(dmabuf_fd);
+	struct aie_dmabuf *adbuf;
+
+	if (IS_ERR(dbuf)) {
+		dev_err(&apart->dev,
+			"failed to get dma address, not able to get dmabuf from %d.\n",
+			dmabuf_fd);
+		return 0;
+	}
+
+	adbuf = aie_part_find_dmabuf(apart, dbuf);
+	dma_buf_put(dbuf);
+	if (!adbuf) {
+		dev_err(&apart->dev,
+			"failed to get dma address, dmabuf %d not attached.\n",
+			dmabuf_fd);
+		return 0;
+	}
+
+	if (off >= dbuf->size || off + len >= dbuf->size) {
+		dev_err(&apart->dev,
+			"failed to get dma address from buf %d, off=0x%llx, len=0x%zx.\n",
+			dmabuf_fd, off, len);
+		return 0;
+	}
+
+	return sg_dma_address(adbuf->sgt->sgl) + off;
+}
+
+/**
+ * aie_part_set_shimdma_bd() - Set the buffer descriptor to AI engine partition
+ *			       hardware
+ * @apart: AI engine partition
+ * @loc: AI engine tile location relative in partition
+ * @bd_id: buffer descriptor ID
+ * @bd: pointer buffer descriptor content
+ * @return: 0 for success, negative value for failure
+ *
+ * This function sets the specified buffer descriptor content to the
+ * specified buffer descriptor in the specified AI engine SHIM NOC tile.
+ */
+static int aie_part_set_shimdma_bd(struct aie_partition *apart,
+				   struct aie_location loc, u32 bd_id, u32 *bd)
+{
+	struct aie_aperture *aperture = apart->aperture;
+	const struct aie_dma_attr *shim_dma = apart->adev->shim_dma;
+	struct aie_location loc_adjust;
+	u32 i, regoff, intile_regoff;
+
+	intile_regoff = shim_dma->bd_regoff + shim_dma->bd_len * bd_id;
+	loc_adjust.col = loc.col + apart->range.start.col;
+	loc_adjust.row = loc.row + apart->range.start.row;
+	regoff = aie_aperture_cal_regoff(aperture, loc_adjust, intile_regoff);
+
+	for (i = 0; i < shim_dma->bd_len / (sizeof(*bd));
+	     i++, regoff += sizeof(*bd))
+		iowrite32(bd[i], aperture->base + regoff);
+	return 0;
+}
+
+/**
+ * aie_part_validate_bdloc() - Validate SHIM DMA buffer descriptor location
+ * @apart: AI engine partition
+ * @loc: tile location
+ * @bd_id: buffer descriptor id
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function validate the SHIM DMA buffer descriptor base address.
+ */
+static int aie_part_validate_bdloc(struct aie_partition *apart,
+				   struct aie_location loc, u32 bd_id)
+{
+	const struct aie_dma_attr *shim_dma = apart->adev->shim_dma;
+	struct aie_location loc_adjust;
+	u32 ttype;
+
+	loc_adjust.col = loc.col + apart->range.start.col;
+	loc_adjust.row = loc.row + apart->range.start.row;
+
+	if (aie_validate_location(apart, loc) < 0) {
+		dev_err(&apart->dev,
+			"invalid loc (%u,%u) in (%u,%u).\n",
+			loc.col, loc.row,
+			apart->range.size.col, apart->range.size.row);
+		return -EINVAL;
+	}
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, &loc_adjust);
+	if (ttype != AIE_TILE_TYPE_SHIMNOC) {
+		dev_err(&apart->dev,
+			"failed to set bd, (%u,%u) is not SHIM NOC\n",
+			loc.col, loc.row);
+		return -EINVAL;
+	}
+
+	if (bd_id >= shim_dma->num_bds) {
+		dev_err(&apart->dev,
+			"invalid SHIM DMA bd id: %u.\n", bd_id);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_attach_dmabuf() - Attach dmabuf to an AI engine
+ * @apart: AI engine partition
+ * @dbuf: pointer to the DMA buffer to attach
+ * @return: pointer to AI engine dmabuf structure for success, or error value
+ *	    for failure
+ *
+ * This function attaches a dmabuf to the specified AI engine partition.
+ */
+static struct aie_dmabuf *aie_part_attach_dmabuf(struct aie_partition *apart,
+						 struct dma_buf *dbuf)
+{
+	struct aie_dmabuf *adbuf;
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+
+	attach = dma_buf_attach(dbuf, &apart->dev);
+	if (IS_ERR(attach)) {
+		dev_err(&apart->dev, "failed to attach dmabuf\n");
+		return ERR_CAST(attach);
+	}
+
+	sgt = dma_buf_map_attachment(attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR(sgt)) {
+		dev_err(&apart->dev, "failed to map dmabuf attachment\n");
+		dma_buf_detach(dbuf, attach);
+		return ERR_CAST(sgt);
+	}
+
+	if (sgt->nents != 1) {
+		dma_addr_t next_sg_addr = sg_dma_address(sgt->sgl);
+		struct scatterlist *s;
+		unsigned int i;
+
+		for_each_sg(sgt->sgl, s, sgt->nents, i) {
+			if (sg_dma_address(s) != next_sg_addr) {
+				dev_err(&apart->dev,
+					"dmabuf not contiguous\n");
+				dma_buf_unmap_attachment(attach, sgt,
+							 attach->dir);
+				dma_buf_detach(dbuf, attach);
+				return ERR_PTR(-EINVAL);
+			}
+
+			next_sg_addr = sg_dma_address(s) + sg_dma_len(s);
+		}
+	}
+
+	adbuf = kmem_cache_alloc(apart->dbufs_cache, GFP_KERNEL);
+	if (!adbuf) {
+		dma_buf_unmap_attachment(attach, sgt, attach->dir);
+		dma_buf_detach(dbuf, attach);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	adbuf->attach = attach;
+	/*
+	 * dmabuf attachment doesn't always include the sgt, store it in
+	 * AI engine dma buf structure.
+	 */
+	adbuf->sgt = sgt;
+
+	refcount_set(&adbuf->refs, 1);
+
+	list_add(&adbuf->node, &apart->dbufs);
+	return adbuf;
+}
+
+/**
+ * aie_part_dmabuf_attach_get() - Get reference to an dmabuf attachment
+ * @adbuf: AI engine partition attached dmabuf
+ *
+ * This call will increase the reference count by 1
+ */
+static void aie_part_dmabuf_attach_get(struct aie_dmabuf *adbuf)
+{
+	refcount_inc(&adbuf->refs);
+}
+
+/**
+ * aie_part_dmabuf_attach_put() - Put reference to an dmabuf attachment
+ * @adbuf: AI engine partition attached dmabuf
+ *
+ * This call will decrease the reference count by 1. If the refcount reaches
+ * 0, it will detach the dmabuf.
+ */
+static void aie_part_dmabuf_attach_put(struct aie_dmabuf *adbuf)
+{
+	struct dma_buf *dbuf;
+	struct aie_partition *apart;
+
+	if (!refcount_dec_and_test(&adbuf->refs))
+		return;
+
+	apart = dev_to_aiepart(adbuf->attach->dev);
+	dbuf = adbuf->attach->dmabuf;
+	dma_buf_unmap_attachment(adbuf->attach, adbuf->sgt, adbuf->attach->dir);
+	dma_buf_detach(dbuf, adbuf->attach);
+	dma_buf_put(dbuf);
+	list_del(&adbuf->node);
+	kmem_cache_free(apart->dbufs_cache, adbuf);
+}
+
+/**
+ * aie_part_release_dmabufs() - detach all the attached dmabufs from partition
+ * @apart: AI engine partition
+ */
+void aie_part_release_dmabufs(struct aie_partition *apart)
+{
+	struct aie_dmabuf *adbuf, *tmpadbuf;
+
+	list_for_each_entry_safe(adbuf, tmpadbuf, &apart->dbufs, node) {
+		struct dma_buf *dbuf = adbuf->attach->dmabuf;
+
+		dma_buf_unmap_attachment(adbuf->attach, adbuf->sgt,
+					 adbuf->attach->dir);
+		dma_buf_detach(dbuf, adbuf->attach);
+		dma_buf_put(dbuf);
+		list_del(&adbuf->node);
+		kmem_cache_free(apart->dbufs_cache, adbuf);
+	}
+}
+
+/**
+ * aie_part_attach_dmabuf_req() - Handle attaching dmabuf to an AI engine
+ *				  partition request
+ * @apart: AI engine partition
+ * @user_args: user AI engine dmabuf argument
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function attaches a dmabuf to the specified AI engine partition and map
+ * the attachment. It checks if the dmabuf is already attached, if it is not
+ * attached, attach it. It returns the number of entries of the attachment to
+ * the AI engine dmabuf user argument. If user wants to know the sg list, it
+ * can use AI engine get sg ioctl.
+ */
+long aie_part_attach_dmabuf_req(struct aie_partition *apart,
+				void __user *user_args)
+{
+	struct aie_dmabuf *adbuf;
+	struct dma_buf *dbuf;
+	long ret;
+	int dmabuf_fd = (int)(uintptr_t)user_args;
+
+	dbuf = dma_buf_get(dmabuf_fd);
+	if (IS_ERR(dbuf)) {
+		dev_err(&apart->dev, "failed to get dmabuf from %d.\n",
+			dmabuf_fd);
+		return PTR_ERR(dbuf);
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dma_buf_put(dbuf);
+		return ret;
+	}
+
+	adbuf = aie_part_find_dmabuf(apart, dbuf);
+	if (!adbuf)
+		adbuf = aie_part_attach_dmabuf(apart, dbuf);
+	else
+		aie_part_dmabuf_attach_get(adbuf);
+
+	mutex_unlock(&apart->mlock);
+
+	if (IS_ERR(adbuf)) {
+		dev_err(&apart->dev, "failed to attach dmabuf\n");
+		dma_buf_put(dbuf);
+		return PTR_ERR(adbuf);
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_detach_dmabuf_req() - Handle detaching dmabuf from an AI engine
+ *				  partition request
+ * @apart: AI engine partition
+ * @user_args: user AI engine dmabuf argument
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function unmaps and detaches a dmabuf from the specified AI engine
+ * partition.
+ */
+long aie_part_detach_dmabuf_req(struct aie_partition *apart,
+				void __user *user_args)
+{
+	int dmabuf_fd;
+	struct dma_buf *dbuf;
+	struct aie_dmabuf *adbuf;
+	int ret;
+
+	dmabuf_fd = (int)(uintptr_t)user_args;
+
+	dbuf = dma_buf_get(dmabuf_fd);
+	if (IS_ERR(dbuf)) {
+		dev_err(&apart->dev, "failed to get dmabuf %d.\n", dmabuf_fd);
+		return PTR_ERR(dbuf);
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dma_buf_put(dbuf);
+		return ret;
+	}
+
+	adbuf = aie_part_find_dmabuf(apart, dbuf);
+	dma_buf_put(dbuf);
+	if (!adbuf) {
+		dev_err(&apart->dev, "failed to find dmabuf %d.\n", dmabuf_fd);
+		mutex_unlock(&apart->mlock);
+		return -EINVAL;
+	}
+
+	aie_part_dmabuf_attach_put(adbuf);
+
+	mutex_unlock(&apart->mlock);
+
+	return 0;
+}
+
+/**
+ * aie_part_set_bd() - Set AI engine SHIM DMA buffer descriptor
+ * @apart: AI engine partition
+ * @user_args: user AI engine dmabuf argument
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function set the user specified buffer descriptor into the SHIM DMA
+ * buffer descriptor.
+ */
+long aie_part_set_bd(struct aie_partition *apart, void __user *user_args)
+{
+	struct aie_device *adev = apart->adev;
+	const struct aie_dma_attr *shim_dma = adev->shim_dma;
+	struct aie_dma_bd_args args;
+	u32 *bd, *tmpbd, buf_len, laddr, haddr, regval;
+	dma_addr_t addr;
+	int ret;
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	ret = aie_part_validate_bdloc(apart, args.loc, args.bd_id);
+	if (ret) {
+		dev_err(&apart->dev, "invalid SHIM DMA BD reg address.\n");
+		return -EINVAL;
+	}
+
+	bd = memdup_user((void __user *)args.bd, shim_dma->bd_len);
+	if (IS_ERR(bd))
+		return PTR_ERR(bd);
+
+	regval = bd[shim_dma->buflen.regoff / sizeof(u32)];
+	buf_len = aie_get_reg_field(&shim_dma->buflen, regval);
+	if (!buf_len) {
+		dev_err(&apart->dev, "no buf length from shim dma bd.\n");
+		kfree(bd);
+		return -EINVAL;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(bd);
+		return ret;
+	}
+
+	/* Get device address from virtual address */
+	addr = aie_part_get_dmabuf_da(apart, (void *)(uintptr_t)args.data_va,
+				      buf_len);
+	if (!addr) {
+		dev_err(&apart->dev, "invalid buffer 0x%llx, 0x%x.\n",
+			args.data_va, buf_len);
+		mutex_unlock(&apart->mlock);
+		kfree(bd);
+		return -EINVAL;
+	}
+
+	/* Set low 32bit address */
+	laddr = lower_32_bits(addr);
+	tmpbd = (u32 *)((char *)bd + shim_dma->laddr.regoff);
+	*tmpbd &= ~shim_dma->laddr.mask;
+	*tmpbd |= aie_get_field_val(&shim_dma->laddr, laddr);
+
+	/* Set high 32bit address */
+	haddr = upper_32_bits(addr);
+	tmpbd = (u32 *)((char *)bd + shim_dma->haddr.regoff);
+	*tmpbd &= ~shim_dma->haddr.mask;
+	*tmpbd |= aie_get_field_val(&shim_dma->haddr, haddr);
+
+	ret = aie_part_set_shimdma_bd(apart, args.loc, args.bd_id, bd);
+	mutex_unlock(&apart->mlock);
+	if (ret)
+		dev_err(&apart->dev, "failed to set to shim dma bd.\n");
+
+	kfree(bd);
+	return ret;
+}
+
+/**
+ * aie_part_set_dmabuf_bd() - Set AI engine SHIM DMA dmabuf buffer descriptor
+ * @apart: AI engine partition
+ * @user_args: user AI engine dmabuf argument
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function set the user specified buffer descriptor into the SHIM DMA
+ * buffer descriptor. The buffer descriptor contained in the @user_args has the
+ * offset to the start of the buffer descriptor.
+ */
+long aie_part_set_dmabuf_bd(struct aie_partition *apart,
+			    void __user *user_args)
+{
+	struct aie_device *adev = apart->adev;
+	const struct aie_dma_attr *shim_dma = adev->shim_dma;
+	struct aie_dmabuf_bd_args args;
+	u32 *bd, *tmpbd, len, laddr, haddr, regval;
+	u64 off;
+	dma_addr_t addr;
+	int ret;
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	ret = aie_part_validate_bdloc(apart, args.loc, args.bd_id);
+	if (ret) {
+		dev_err(&apart->dev, "invalid SHIM DMA BD reg address.\n");
+		return -EINVAL;
+	}
+
+	bd = memdup_user((void __user *)args.bd, shim_dma->bd_len);
+	if (IS_ERR(bd))
+		return PTR_ERR(bd);
+
+	regval = bd[shim_dma->buflen.regoff / sizeof(u32)];
+	len = aie_get_reg_field(&shim_dma->buflen, regval);
+	if (!len) {
+		dev_err(&apart->dev, "no buf length from shim dma bd.\n");
+		kfree(bd);
+		return -EINVAL;
+	}
+
+	/* Get low 32bit address offset */
+	tmpbd = (u32 *)((char *)bd + shim_dma->laddr.regoff);
+	laddr = *tmpbd & shim_dma->laddr.mask;
+	/* Get high 32bit address offset */
+	tmpbd = (u32 *)((char *)bd + shim_dma->haddr.regoff);
+	haddr = *tmpbd & shim_dma->haddr.mask;
+	off = laddr | ((u64)haddr << 32);
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(bd);
+		return ret;
+	}
+
+	/* Get device address from offset */
+	addr = aie_part_get_dmabuf_da_from_off(apart, args.buf_fd, off, len);
+	if (!addr) {
+		dev_err(&apart->dev, "invalid buffer 0x%llx, 0x%x.\n",
+			off, len);
+		mutex_unlock(&apart->mlock);
+		kfree(bd);
+		return -EINVAL;
+	}
+
+	/* Set low 32bit address */
+	laddr = lower_32_bits(addr);
+	tmpbd = (u32 *)((char *)bd + shim_dma->laddr.regoff);
+	*tmpbd &= ~shim_dma->laddr.mask;
+	*tmpbd |= aie_get_field_val(&shim_dma->laddr, laddr);
+
+	/* Set high 32bit address */
+	haddr = upper_32_bits(addr);
+	tmpbd = (u32 *)((char *)bd + shim_dma->haddr.regoff);
+	*tmpbd &= ~shim_dma->haddr.mask;
+	*tmpbd |= aie_get_field_val(&shim_dma->haddr, haddr);
+
+	ret = aie_part_set_shimdma_bd(apart, args.loc, args.bd_id, bd);
+	mutex_unlock(&apart->mlock);
+	if (ret)
+		dev_err(&apart->dev, "failed to set to shim dma bd.\n");
+
+	kfree(bd);
+	return ret;
+}
+
+/**
+ * aie_part_prealloc_dbufs_cache() - Preallocate dmabuf descriptors memory
+ *
+ * @apart: AI engine partition
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function preallocate memories to save dmabuf descriptors. When dmabuf
+ * is attached to the partition at runtime, it can get the descriptor memory
+ * from this preallocated memory pool.
+ */
+int aie_part_prealloc_dbufs_cache(struct aie_partition *apart)
+{
+	struct kmem_cache *dbufs_cache;
+	char name[64];
+
+	sprintf(name, "%s_dbufs", dev_name(&apart->dev));
+	dbufs_cache = kmem_cache_create(name, sizeof(struct aie_dmabuf),
+					0, 0, NULL);
+	if (!dbufs_cache)
+		return -ENOMEM;
+
+	apart->dbufs_cache = dbufs_cache;
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-internal.h
@@ -0,0 +1,1175 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Xilinx AI Engine driver internal header
+ *
+ * Copyright (C) 2020 - 2021 Xilinx, Inc.
+ */
+
+#ifndef AIE_INTERNAL_H
+#define AIE_INTERNAL_H
+
+#include <linux/bitfield.h>
+#include <linux/bitmap.h>
+#include <linux/bits.h>
+#include <linux/cdev.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/file.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <uapi/linux/xlnx-ai-engine.h>
+
+#define AIE_DEVICE_GEN_AIE	1U
+#define AIE_DEVICE_GEN_AIEML	2U
+
+/*
+ * Macros for AI engine tile type bitmasks
+ */
+enum aie_tile_type {
+	AIE_TILE_TYPE_TILE,
+	AIE_TILE_TYPE_SHIMPL,
+	AIE_TILE_TYPE_SHIMNOC,
+	AIE_TILE_TYPE_MEMORY,
+	AIE_TILE_TYPE_MAX
+};
+
+#define AIE_TILE_TYPE_MASK_TILE		BIT(AIE_TILE_TYPE_TILE)
+#define AIE_TILE_TYPE_MASK_SHIMPL	BIT(AIE_TILE_TYPE_SHIMPL)
+/* SHIM NOC tile includes SHIM PL and SHIM NOC modules */
+#define AIE_TILE_TYPE_MASK_SHIMNOC	BIT(AIE_TILE_TYPE_SHIMNOC)
+#define AIE_TILE_TYPE_MASK_MEMORY	BIT(AIE_TILE_TYPE_MEMORY)
+
+/*
+ * Macros for attribute property of AI engine registers accessed by kernel
+ * 0 - 7 bits: tile type bits
+ * 8 - 15 bits: permission bits. If it is 1, it allows write from userspace
+ */
+#define AIE_REGS_ATTR_TILE_TYPE_SHIFT	0U
+#define AIE_REGS_ATTR_PERM_SHIFT	8U
+#define AIE_REGS_ATTR_TILE_TYPE_MASK	GENMASK(AIE_REGS_ATTR_PERM_SHIFT - 1, \
+						AIE_REGS_ATTR_TILE_TYPE_SHIFT)
+#define AIE_REGS_ATTR_PERM_MASK		GENMASK(15, \
+						AIE_REGS_ATTR_PERM_SHIFT)
+
+#define KBYTES(n)	((n) * 1024)
+
+/* Silicon Engineering Sample(ES) revision ID */
+#define VERSAL_ES1_REV_ID		0x0
+#define VERSAL_ES2_REV_ID		0x1
+
+#define AIE_NPI_ERROR_ID		BIT(1)
+
+/* Macros relevant to interrupts */
+#define AIE_INTR_L2_CTRL_MASK_WIDTH	32U
+
+/* Max number of modules per tile */
+#define AIE_MAX_MODS_PER_TILE		2U
+
+/* AIE core registers step size */
+#define AIE_CORE_REGS_STEP		0x10
+
+/*
+ * Macros of AI engine module type index of a tile type
+ * e.g.
+ * id 0 of CORE tile is memory module, and 1 is core module
+ * id 0 of SHIM tile is pl module, and 1 is noc module
+ */
+#define AIE_TILE_MOD_START		AIE_MEM_MOD
+#define AIE_MOD_ID(T, M)		((M) - AIE_##T ## _MOD_START)
+#define AIE_TILE_MEM_MOD_ID		AIE_MOD_ID(TILE, AIE_MEM_MOD)
+#define AIE_TILE_CORE_MOD_ID		AIE_MOD_ID(TILE, AIE_CORE_MOD)
+#define AIE_SHIMPL_MOD_START		AIE_PL_MOD
+#define AIE_SHIMNOC_MOD_START		AIE_PL_MOD
+#define AIE_SHIM_PL_MOD_ID		AIE_MOD_ID(SHIMPL, AIE_PL_MOD)
+#define AIE_SHIM_NOC_MOD_ID		AIE_MOD_ID(SHIMNOC, AIE_NOC_MOD)
+
+/* String delimiter to format sysfs data */
+#define DELIMITER_LEVEL0 "|"
+#define DELIMITER_LEVEL1 ", "
+#define DELIMITER_LEVEL2 "; "
+
+/* Macros to define size of temporary string buffers */
+#define AIE_SYSFS_CORE_STS_SIZE		100U
+#define AIE_SYSFS_CHAN_STS_SIZE		150U
+#define AIE_SYSFS_QUEUE_SIZE_SIZE	40U
+#define AIE_SYSFS_QUEUE_STS_SIZE	60U
+#define AIE_SYSFS_BD_SIZE		40U
+#define AIE_SYSFS_FIFO_LEN_SIZE		40U
+#define AIE_SYSFS_ERROR_SIZE		300U
+#define AIE_SYSFS_ERROR_CATEGORY_SIZE	500U
+#define AIE_SYSFS_LOCK_STS_SIZE		400U
+#define AIE_SYSFS_EVENT_STS_SIZE	550U
+
+/* Helper macros to dynamically create sysfs device attribute */
+#define AIE_PART_DEV_ATTR_RO(_name) {				\
+	.name		= __stringify(_name),			\
+	.mode		= 0444,					\
+	.show		= aie_part_show_##_name,		\
+}
+
+#define AIE_PART_DEV_ATTR_WO(_name) {				\
+	.name		= __stringify(_name),			\
+	.mode		= 0200,					\
+	.store		= aie_part_store_##_name,		\
+}
+
+#define AIE_PART_DEV_ATTR_RW(_name) {				\
+	.name		= __stringify(_name),			\
+	.mode		= 0644,					\
+	.show		= aie_part_show_##_name,		\
+	.store		= aie_part_store_##_name,		\
+}
+
+#define AIE_TILE_DEV_ATTR_RO(_name, _ttype) {			\
+	.name		= __stringify(_name),			\
+	.mode		= 0444,					\
+	.tile_type	= _ttype,				\
+	.show		= aie_tile_show_##_name,		\
+}
+
+#define AIE_TILE_DEV_ATTR_WO(_name, _ttype) {			\
+	.name		= __stringify(_name),			\
+	.mode		= 0200,					\
+	.tile_type	= _ttype,				\
+	.store		= aie_tile_store_##_name,		\
+}
+
+#define AIE_TILE_DEV_ATTR_RW(_name, _ttype) {			\
+	.name		= __stringify(_name),			\
+	.mode		= 0644,					\
+	.tile_type	= _ttype,				\
+	.show		= aie_tile_show_##_name,		\
+	.store		= aie_tile_store_##_name,		\
+}
+
+#define AIE_PART_BIN_ATTR_RO(_name, _size) {			\
+	.name		= __stringify(_name),			\
+	.mode		= 0444,					\
+	.size		= _size,				\
+	.read		= aie_sysfs_read_handler,		\
+	.read_callback	= aie_part_read_cb_##_name,		\
+}
+
+#define AIE_PART_BIN_ATTR_WO(_name, _size) {			\
+	.name		= __stringify(_name),			\
+	.mode		= 0200,					\
+	.size		= _size,				\
+	.write		= aie_part_write_handler,		\
+	.write_callback	= aie_part_write_cb_##_name,		\
+}
+
+#define AIE_PART_BIN_ATTR_RW(_name, _size) {			\
+	.name		= __stringify(_name),			\
+	.mode		= 0644					\
+	.size		= _size,				\
+	.read		= aie_sysfs_read_handler,		\
+	.write		= aie_part_write_handler,		\
+	.read_callback	= aie_part_read_cb_##_name,		\
+	.write_callback	= aie_part_write_cb_##_name,		\
+}
+
+#define AIE_TILE_BIN_ATTR_RO(_name, _size, _ttype) {		\
+	.name		= __stringify(_name),			\
+	.mode		= 0444,					\
+	.size		= _size,				\
+	.tile_type	= _ttype,				\
+	.read		= aie_sysfs_read_handler,		\
+	.read_callback	= aie_tile_read_cb_##_name,		\
+}
+
+#define AIE_TILE_BIN_ATTR_WO(_name, _size, _ttype) {		\
+	.name		= __stringify(_name),			\
+	.mode		= 0200,					\
+	.size		= _size,				\
+	.tile_type	= _ttype,				\
+	.write		= aie_tile_write_handler,		\
+	.write_callback	= aie_tile_write_cb_##_name,		\
+}
+
+#define AIE_TILE_BIN_ATTR_RW(_name, _size, _ttype) {		\
+	.name		= __stringify(_name),			\
+	.mode		= 0644,					\
+	.size		= _size,				\
+	.tile_type	= _ttype,				\
+	.read		= aie_sysfs_read_handler,		\
+	.write		= aie_tile_write_handler,		\
+	.read_callback	= aie_tile_read_cb_##_name,		\
+	.write_callback	= aie_tile_write_cb_##_name,		\
+}
+
+/*
+ * enum aie_shim_switch_type - identifies different switches in shim tile.
+ */
+enum aie_shim_switch_type {
+	AIE_SHIM_SWITCH_A,
+	AIE_SHIM_SWITCH_B
+};
+
+/**
+ * struct aie_tile_regs - contiguous range of AI engine register
+ *			  within an AI engine tile
+ * @soff: start offset of the range
+ * @eoff: end offset of the range
+ * @attribute: registers attribute. It uses AIE_REGS_ATTR_* macros defined
+ *	       above.
+ */
+struct aie_tile_regs {
+	size_t soff;
+	size_t eoff;
+	u32 attribute;
+};
+
+/**
+ * struct aie_single_reg_field - AI engine single field register attribute
+ * @mask: field mask
+ * @regoff: register offset of the field
+ */
+struct aie_single_reg_field {
+	u32 mask;
+	u32 regoff;
+};
+
+struct aie_device;
+struct aie_partition;
+
+/**
+ * struct aie_part_mem - AI engine partition memory information structure
+ * @apart: AI engine partition
+ * @dbuf: dmabuf pointer associated with the memory
+ * @mem: memory information of a type of memory
+ * @size: size of the total memories in the partition
+ *
+ * This structure is to keep the information of a type of memory in a
+ * partition. The memory information will be stored in @mem property.
+ * The following information will be keep:
+ *  * memory start address offset within a tile
+ *  * memory size
+ *  * what tiles contain this type of memory
+ */
+struct aie_part_mem {
+	struct aie_partition *apart;
+	struct dma_buf *dbuf;
+	struct aie_mem mem;
+	size_t size;
+};
+
+/**
+ * struct aie_dma_attr - AI engine DMA attributes structure
+ * @laddr: low address field attributes
+ * @haddr: high address field attributes
+ * @buflen: buffer length field attributes
+ * @sts: channel status field attributes
+ * @stall: queue stall status field attributes
+ * @qsize: queue size field attributes
+ * @curbd: current buffer descriptor field attributes
+ * @qsts: queue status field attributes
+ * @fifo_cnt: FIFO counter field attributes
+ * @bd_regoff: SHIM DMA buffer descriptors register offset
+ * @mm2s_sts_regoff: MM2S status register offset
+ * @s2mm_sts_regoff: S2MM status register offset
+ * @fifo_cnt_regoff: FIFO counter register offset
+ * @num_mm2s_chan: number of MM2S channels
+ * @num_s2mm_chan: number of S2MM channels
+ * @num_bds: number of buffer descriptors
+ * @bd_len: length of a buffer descriptor in bytes
+ */
+struct aie_dma_attr {
+	struct aie_single_reg_field laddr;
+	struct aie_single_reg_field haddr;
+	struct aie_single_reg_field buflen;
+	struct aie_single_reg_field sts;
+	struct aie_single_reg_field stall;
+	struct aie_single_reg_field qsize;
+	struct aie_single_reg_field curbd;
+	struct aie_single_reg_field qsts;
+	struct aie_single_reg_field fifo_cnt;
+	u32 bd_regoff;
+	u32 mm2s_sts_regoff;
+	u32 s2mm_sts_regoff;
+	u32 fifo_cnt_regoff;
+	u32 num_mm2s_chan;
+	u32 num_s2mm_chan;
+	u32 num_bds;
+	u32 bd_len;
+};
+
+/**
+ * struct aie_core_regs_attr - AI engine core register attributes structure
+ * @core_regs: core registers
+ * @width: number of 32 bit words
+ */
+struct aie_core_regs_attr {
+	const struct aie_tile_regs *core_regs;
+	u32 width;
+};
+
+struct aie_aperture;
+/**
+ * struct aie_tile_operations - AI engine device operations
+ * @get_tile_type: get type of tile based on tile operation
+ * @get_mem_info: get different types of memories information
+ * @get_core_status: get the status of AIE core.
+ * @reset_shim: reset shim, it will assert and then release SHIM reset
+ * @init_part_clk_state: initialize clock states software structure which is a
+ *			 bitmap for the AI engine partition. The clock states
+ *			 structure is the structure used to keep track of if
+ *			 the modules in the AI engine partition are gated.
+ * @scan_part_clocks: scan partition modules to check whether the modules are
+ *		      clock gated or not, and update the soft clock states
+ *		      structure. It is required to be called when the partition
+ *		      is requested so that the driver knows which modules are
+ *		      clock gated when the partition is requested. This function
+ *		      expects the caller to apply partition lock before calling
+ *		      this function.
+ * @set_part_clocks: set partition modules clocks gate registers based on the
+ *		     partition clock states bitmap. This function expects the
+ *		     caller to apply partition lock before calling this
+ *		     function. The caller function will need to set the bitmap
+ *		     on which tiles are required to be clocked on.
+ * @mem_clear: clear data memory banks of the partition.
+ *
+ * Different AI engine device version has its own device
+ * operation.
+ */
+struct aie_tile_operations {
+	u32 (*get_tile_type)(struct aie_device *adev, struct aie_location *loc);
+	unsigned int (*get_mem_info)(struct aie_device *adev,
+				     struct aie_range *range,
+				     struct aie_part_mem *pmem);
+	u32 (*get_core_status)(struct aie_partition *apart,
+			       struct aie_location *loc);
+	int (*reset_shim)(struct aie_aperture *aperture,
+			  struct aie_range *range);
+	int (*init_part_clk_state)(struct aie_partition *apart);
+	int (*scan_part_clocks)(struct aie_partition *apart);
+	int (*set_part_clocks)(struct aie_partition *apart);
+	int (*mem_clear)(struct aie_partition *apart);
+};
+
+/**
+ * struct aie_resource - AI engine resource structure
+ * @bitmap: resource bitmap
+ * @total: total number of resource
+ */
+struct aie_resource {
+	unsigned long *bitmap;
+	u32 total;
+};
+
+/**
+ * struct aie_event_attr - AI Engine event attributes structure.
+ * @bc_event: broadcast event attribute to capture event mask value and
+ *	      register offset from @bc_regoff.
+ * @group_error: group error attribute to capture error group mask value and
+ *		 register offset value from @group_regoff.
+ * @bc_regoff: base broadcast register offset.
+ * @status_regoff: base status register offset.
+ * @group_regoff: base group error register offset.
+ * @base_error_event: event ID of first error event in a group error.
+ * @num_broadcasts: total number of broadcast events.
+ * @base_bc_event: broadcast 0 vent ID
+ * @num_events: total number of events.
+ */
+struct aie_event_attr {
+	struct aie_single_reg_field bc_event;
+	struct aie_single_reg_field group_error;
+	u32 bc_regoff;
+	u32 status_regoff;
+	u32 group_regoff;
+	u32 base_error_event;
+	u32 num_broadcasts;
+	u32 base_bc_event;
+	u32 num_events;
+};
+
+/**
+ * struct aie_l1_intr_ctrl_attr - AI engine level 1 interrupt controller
+ *				  attributes structure.
+ * @mask: level 1 interrupt controller mask attribute.
+ * @swa_status: switch A level 1 interrupt controller status attribute.
+ * @swb_status: switch A level 1 interrupt controller status attribute.
+ * @swa_event: switch A level 1 interrupt controller event attribute.
+ * @swb_event: switch A level 1 interrupt controller event attribute.
+ * @regoff: base level 1 interrupt controller register offset.
+ * @event_lsb: lsb of IRQ event within IRQ event switch register.
+ * @num_broadcasts: total number of broadcast signals to level 1 interrupt
+ *		    controller.
+ */
+struct aie_l1_intr_ctrl_attr {
+	struct aie_single_reg_field swa_status;
+	struct aie_single_reg_field swb_status;
+	struct aie_single_reg_field swa_event;
+	struct aie_single_reg_field swb_event;
+	u32 regoff;
+	u32 event_lsb;
+	u32 num_broadcasts;
+};
+
+/**
+ * struct aie_l2_intr_ctrl_attr - AI engine level 2 interrupt controller
+ *				  attributes structure.
+ * @mask: level 2 interrupt controller mask attribute.
+ * @enable: level 2 interrupt controller enable attribute.
+ * @disable: level 2 interrupt controller disable attribute.
+ * @status: level 2 interrupt controller status attribute.
+ * @regoff: level 2 interrupt controller register offset.
+ * @num_broadcasts: total number of broadcast signals to level 2 interrupt
+ *		    controller.
+ */
+struct aie_l2_intr_ctrl_attr {
+	struct aie_single_reg_field mask;
+	struct aie_single_reg_field enable;
+	struct aie_single_reg_field disable;
+	struct aie_single_reg_field status;
+	u32 regoff;
+	u32 num_broadcasts;
+};
+
+/**
+ * struct aie_error_cb - AI engine error callback struct.
+ * @cb: pointer to callback function.
+ * @priv: data to be passed to the callback function.
+ */
+struct aie_error_cb {
+	void (*cb)(void *priv);
+	void *priv;
+};
+
+/**
+ * struct aie_event_prop - AI engine event property.
+ * @event: error event ID.
+ * @event_str: error string.
+ */
+struct aie_event_prop {
+	u32 event;
+	char *event_str;
+};
+
+/**
+ * struct aie_err_category - AI engine errors category.
+ * @err_category: category of error.
+ * @num_events: number of event IDs in a category.
+ * @prop: pointer to an array event properties.
+ */
+struct aie_err_category {
+	u32 err_category;
+	u32 num_events;
+	const struct aie_event_prop *prop;
+};
+
+/**
+ * struct aie_error_attr - AI engine error attribute.
+ * @num_err_categories: number of possible error categories valid for a given
+ *			module.
+ * @err_category: pointer to an array of error categories.
+ */
+struct aie_error_attr {
+	u32 num_err_categories;
+	const struct aie_err_category *err_category;
+};
+
+/**
+ * struct aie_rsc_stat - AI engine hardware resource status bitmap of a
+ *			 resource of a module type of a tile type of an AI
+ *			 engine partition
+ * @rbits: runtime allocated resource bitmap
+ * @sbits: static resource bitmap for resources allocated at compilation
+ *	   time
+ */
+struct aie_rsc_stat {
+	struct aie_resource rbits;
+	struct aie_resource sbits;
+};
+
+/**
+ * struct aie_mod_rscs - AI engine hardware resource status bitmaps of
+ *			 a module type of a tile type of an AI engine
+ *			 partition.
+ * @rscs_stat: resource status bitmaps
+ */
+struct aie_mod_rscs {
+	struct aie_rsc_stat *rscs_stat;
+};
+
+/**
+ * struct aie_tile_rscs - AI engine hardware resource status bitmaps of all
+ *			  resources of a tile type of a partition.
+ * @mod_rscs: array of pointers of AI engine resources. Each element is an
+ *	      array of hardware resources of different modules of a particular
+ *	      resource type of a tile type.
+ *	      e.g. if the tile type is TILE. The rscs are an arrary of
+ *	      resources bitmap of all the defined AI engine resources types of
+ *	      TILE type. e.g. the element of AIE_RSCTYPE_PERF. It is an array
+ *	      of perfcounter resources bitmaps for both core module and memory
+ *	      module of TILE type of an AI engine partition.
+ */
+struct aie_tile_rscs {
+	struct aie_mod_rscs *mod_rscs[AIE_RSCTYPE_MAX];
+};
+
+/**
+ * struct aie_mod_rsc_attr - AI engine resource attribute of a module
+ * @num_rscs: number of resource
+ */
+struct aie_mod_rsc_attr {
+	u8 num_rscs;
+};
+
+/**
+ * struct aie_tile_rsc_attr - AI engine resource attributes
+ * @mod_attr: array of resource attribute different modules of a tile type of
+ *	      a particular resource type.
+ */
+struct aie_tile_rsc_attr {
+	struct aie_mod_rsc_attr mod_attr[AIE_MAX_MODS_PER_TILE];
+};
+
+/**
+ * struct aie_lock_attr - AI engine lock attributes
+ * @sts: lock status field attributes
+ * @sts_regoff: lock status register offset
+ * @num_locks: number of locks
+ */
+struct aie_lock_attr {
+	struct aie_single_reg_field sts;
+	u32 sts_regoff;
+	u32 num_locks;
+};
+
+/**
+ * struct aie_tile_attr - AI engine device tile type attributes
+ * @start_row: start row
+ * @num_rows: number of rows
+ * @num_mods: number of modules of this tile type
+ * @mods: array of module types of this tile type
+ * @rscs_attr: resources attributes array. Each element is an array of
+ *	       attributes of a resource type of a tile type.
+ */
+struct aie_tile_attr {
+	u8 start_row;
+	u8 num_rows;
+	u8 num_mods;
+	const enum aie_module_type *mods;
+	const struct aie_tile_rsc_attr *rscs_attr;
+};
+
+/**
+ * struct aie_dev_attr - device attribute properties for AI Engine sysfs nodes.
+ * @name: name of the device attribute
+ * @mode: permissions associated
+ * @tile_type: tile type(s) attribute is valid for. use AIE_TILE_TYPE_MASK_*.
+ * @show: read function handler
+ * @store: write function handler
+ */
+struct aie_dev_attr {
+	const char *name;
+	umode_t mode;
+	u32 tile_type;
+	ssize_t (*show)(struct device *dev, struct device_attribute *attr,
+			char *buf);
+	ssize_t (*store)(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count);
+};
+
+/**
+ * struct aie_sysfs_prop - private data passed to the sysfs read/write handler.
+ * @data: buffer to export sysfs data
+ * @size: size of data exported
+ * @max_size: max size of data that could be exported
+ * @read_callback: callback to fetch data from on read
+ * @write_callback: callback to send data to on write
+ */
+struct aie_sysfs_prop {
+	char *data;
+	ssize_t size;
+	ssize_t max_size;
+	ssize_t (*read_callback)(struct kobject *kobj, char *buffer,
+				 ssize_t size);
+	ssize_t (*write_callback)(struct kobject *kobj, char *buffer,
+				  ssize_t size);
+};
+
+/**
+ * struct aie_bin_attr - binary attribute properties for AI Engine sysfs nodes
+ * @name: name of the binary attribute
+ * @mode: permissions associated
+ * @size: size of the buffer to be allocated
+ * @tile_type: tile type(s) attribute is valid for. use AIE_TILE_TYPE_MASK_*.
+ * @read: read handler
+ * @write: write handler
+ * @read_callback: callback to fetch data from on read
+ * @write_callback:  callback to send data to on write
+ */
+struct aie_bin_attr {
+	const char *name;
+	umode_t mode;
+	ssize_t size;
+	u32 tile_type;
+	ssize_t (*read)(struct file *filp, struct kobject *kobj,
+			struct bin_attribute *attr, char *buf, loff_t offset,
+			size_t max_size);
+	ssize_t (*write)(struct file *filp, struct kobject *kobj,
+			 struct bin_attribute *attr, char *buf, loff_t offset,
+			 size_t max_size);
+	ssize_t (*read_callback)(struct kobject *kobj, char *buffer,
+				 ssize_t size);
+	ssize_t (*write_callback)(struct kobject *kobj, char *buffer,
+				  ssize_t size);
+};
+
+/**
+ * struct aie_sysfs_attr - captures all sysfs attributes defined at
+ *			   partition or tile level.
+ * @dev_attr: pointer to array of device attributes
+ * @bin_attr: pointer to array of binary attributes
+ * @num_dev_attrs: number of device attributes
+ * @num_bin_attrs: number of binary attributes
+ */
+struct aie_sysfs_attr {
+	const struct aie_dev_attr *dev_attr;
+	const struct aie_bin_attr *bin_attr;
+	u32 num_dev_attrs;
+	u32 num_bin_attrs;
+};
+
+/**
+ * struct aie_tile - AI engine tile structure
+ * @loc: tile co-ordinates
+ * @apart: parent partition the tile belongs to
+ * @dev: device for the AI engine tile device
+ * @attr_grp: attribute group
+ */
+struct aie_tile {
+	struct aie_location loc;
+	struct aie_partition *apart;
+	struct device dev;
+	struct attribute_group *attr_grp;
+};
+
+/**
+ * struct aie_device - AI engine device structure
+ * @apertures: list of apertures
+ * @cdev: cdev for the AI engine
+ * @dev: device for the AI engine device
+ * @mlock: protection for AI engine device operations
+ * @clk: AI enigne device clock
+ * @kernel_regs: array of kernel only registers
+ * @core_regs: array of core registers
+ * @ops: tile operations
+ * @col_rst: column reset attribute
+ * @col_clkbuf: column clock buffer attribute
+ * @shim_dma: SHIM DMA attribute
+ * @tile_dma: tile DMA attribute
+ * @pl_events: pl module event attribute
+ * @mem_events: memory module event attribute
+ * @core_events: core module event attribute
+ * @l1_ctrl: level 1 interrupt controller attribute
+ * @l2_ctrl: level 2 interrupt controller attribute
+ * @core_errors: core module error attribute
+ * @mem_errors: memory module error attribute
+ * @shim_errors: shim tile error attribute
+ * @array_shift: array address shift
+ * @col_shift: column address shift
+ * @row_shift: row address shift
+ * @dev_gen: aie hardware device generation
+ * @cols_res: AI engine columns resources to indicate
+ *	      while columns are occupied by partitions.
+ * @num_kernel_regs: number of kernel only registers range
+ * @num_core_regs: number of core registers range
+ * @version: AI engine device version
+ * @pm_node_id: AI Engine platform management node ID
+ * @clock_id: AI Engine clock ID
+ * @ttype_attr: tile type attributes
+ * @part_sysfs_attr: partition level sysfs attributes
+ * @tile_sysfs_attr: tile level sysfs attributes
+ * @core_status_str: core status in string format
+ * @core_pc: program counter attribute
+ * @core_lr: link register attribute
+ * @core_sp: stack pointer attribute
+ * @dma_status_str: DMA channel status in string format
+ * @queue_status_str: DMA queue status in string format
+ * @pl_lock: PL module lock attribute
+ * @mem_lock: memory module lock attribute
+ * @lock_status_str: lock status in string format
+ */
+struct aie_device {
+	struct list_head apertures;
+	struct cdev cdev;
+	struct device dev;
+	struct mutex mlock; /* protection for AI engine apertures */
+	struct clk *clk;
+	const struct aie_tile_regs *kernel_regs;
+	const struct aie_core_regs_attr *core_regs;
+	const struct aie_tile_operations *ops;
+	const struct aie_single_reg_field *col_rst;
+	const struct aie_single_reg_field *col_clkbuf;
+	const struct aie_dma_attr *shim_dma;
+	const struct aie_dma_attr *tile_dma;
+	const struct aie_event_attr *pl_events;
+	const struct aie_event_attr *mem_events;
+	const struct aie_event_attr *core_events;
+	const struct aie_l1_intr_ctrl_attr *l1_ctrl;
+	const struct aie_l2_intr_ctrl_attr *l2_ctrl;
+	const struct aie_error_attr *core_errors;
+	const struct aie_error_attr *mem_errors;
+	const struct aie_error_attr *shim_errors;
+	u32 array_shift;
+	u32 col_shift;
+	u32 row_shift;
+	u32 dev_gen;
+	u32 num_kernel_regs;
+	u32 num_core_regs;
+	int version;
+	u32 pm_node_id;
+	u32 clock_id;
+	struct aie_tile_attr ttype_attr[AIE_TILE_TYPE_MAX];
+	const struct aie_sysfs_attr *part_sysfs_attr;
+	const struct aie_sysfs_attr *tile_sysfs_attr;
+	char **core_status_str;
+	const struct aie_single_reg_field *core_pc;
+	const struct aie_single_reg_field *core_lr;
+	const struct aie_single_reg_field *core_sp;
+	char **dma_status_str;
+	char **queue_status_str;
+	const struct aie_lock_attr *pl_lock;
+	const struct aie_lock_attr *mem_lock;
+	char **lock_status_str;
+};
+
+/**
+ * struct aie_aperture - AI engine aperture structure
+ * @node: list node
+ * @partitions: list of partitions of this aperture
+ * @adev: pointer to AI device instance
+ * @mlock: protection for AI engine aperture operations
+ * @base: AI engine aperture base virtual address
+ * @res: memory resource of AI engine aperture
+ * @dev: device of aperture
+ * @cols_res: AI engine columns resources to indicate
+ *	      while columns are occupied by partitions.
+ * @node_id: AI engine aperture node id which is to identify
+ *	     the aperture in the system in firmware
+ * @irq: Linux IRQ number
+ * @range: range of aperture
+ * @backtrack: workqueue to backtrack interrupt
+ * @l2_mask: level 2 interrupt controller mask bitmap
+ */
+struct aie_aperture {
+	struct list_head node;
+	struct list_head partitions;
+	struct aie_device *adev;
+	struct mutex mlock; /* protection for AI engine aperture operations */
+	void __iomem *base;
+	struct resource res;
+	struct device dev;
+	struct aie_resource cols_res;
+	u32 node_id;
+	int irq;
+	struct aie_range range;
+	struct work_struct backtrack;
+	struct aie_resource l2_mask;
+};
+
+/**
+ * struct aie_partition - AI engine partition structure
+ * @node: list node
+ * @dbufs: dmabufs list
+ * @aperture: pointer to AI engine aperture
+ * @adev: pointer to AI device instance
+ * @filep: pointer to file for refcount on the users of the partition
+ * @pmems: pointer to partition memories types
+ * @dbufs_cache: memory management object for preallocated dmabuf descriptors
+ * @trscs: resources bitmaps for each tile
+ * @freq_req: required frequency
+ * @range: range of partition
+ * @mlock: protection for AI engine partition operations
+ * @dev: device for the AI engine partition
+ * @atiles: pointer to an array of AIE tile structure.
+ * @cores_clk_state: bitmap to indicate the power state of core modules
+ * @tiles_inuse: bitmap to indicate if a tile is in use
+ * @error_cb: error callback
+ * @core_event_status: core module event bitmap
+ * @mem_event_status: memory module event bitmap
+ * @pl_event_status: pl module event bitmap
+ * @attr_grp: attribute group
+ * @partition_id: partition id. Partition ID is the identifier
+ *		  of the AI engine partition in the system.
+ * @status: indicate if the partition is in use
+ * @cntrflag: partition control flag. e.g. whether to reset columns when
+ *	      the partition is released
+ * @error_to_report: indicates if there are errors pending to be reported to
+ *		     the application. This value is set to true if errors are
+ *		     found during backtracking, and error interrupt was
+ *		     received when partition was not requested yet.
+ */
+struct aie_partition {
+	struct list_head node;
+	struct list_head dbufs;
+	struct aie_aperture *aperture;
+	struct aie_device *adev;
+	struct file *filep;
+	struct aie_part_mem *pmems;
+	struct kmem_cache *dbufs_cache;
+	struct aie_tile_rscs trscs[AIE_TILE_TYPE_MAX];
+	u64 freq_req;
+	struct aie_range range;
+	struct mutex mlock; /* protection for AI engine partition operations */
+	struct device dev;
+	struct aie_tile *atiles;
+	struct aie_resource cores_clk_state;
+	struct aie_resource tiles_inuse;
+	struct aie_error_cb error_cb;
+	struct aie_resource core_event_status;
+	struct aie_resource mem_event_status;
+	struct aie_resource pl_event_status;
+	struct attribute_group *attr_grp;
+	u32 partition_id;
+	u32 status;
+	u32 cntrflag;
+	u8 error_to_report;
+};
+
+/**
+ * struct aie_part_pinned_region - AI engine user space pinned region
+ * @user_addr: user space address
+ * @len: length of the user space buffer in bytes
+ * @npages: number of pages of the user space buffer
+ * @pages: array to receive pointers to the pages pinned.
+ *	   should be at least npages long
+ */
+struct aie_part_pinned_region {
+	u64 user_addr;
+	u64 len;
+	struct page **pages;
+	int npages;
+};
+
+extern struct class *aie_class;
+extern const struct file_operations aie_part_fops;
+
+#define cdev_to_aiedev(i_cdev) container_of((i_cdev), struct aie_device, cdev)
+#define dev_to_aiedev(_dev) container_of((_dev), struct aie_device, dev)
+#define dev_to_aiepart(_dev) container_of((_dev), struct aie_partition, dev)
+#define dev_to_aietile(_dev) container_of((_dev), struct aie_tile, dev)
+
+#define aie_col_mask(adev) ({ \
+	struct aie_device *_adev = (adev); \
+	GENMASK_ULL(_adev->array_shift - 1, _adev->col_shift);  \
+	})
+
+#define aie_row_mask(adev) ({ \
+	struct aie_device *_adev = (adev); \
+	GENMASK_ULL(_adev->col_shift - 1, _adev->row_shift);  \
+	})
+
+#define aie_tile_reg_mask(adev) ({ \
+	struct aie_device *_adev = (adev); \
+	GENMASK_ULL(_adev->row_shift - 1, 0);  \
+	})
+
+/*
+ * Need to define field get, as AI engine shift mask is not constant.
+ * Cannot use FIELD_GET()
+ */
+#define aie_tile_reg_field_get(mask, shift, regoff) ( \
+	((regoff) & (mask)) >> (shift))
+
+#define aie_cal_tile_reg(adev, regoff) ( \
+	aie_tile_reg_field_get(aie_tile_reg_mask(adev), 0, regoff))
+
+/**
+ * aie_get_field_val() - calculate value of an AI engine register field
+ * @field: a field in a register
+ * @val: value of the field
+ * @return: value of a register field
+ */
+static inline u32 aie_get_field_val(const struct aie_single_reg_field *field,
+				    u32 val)
+{
+	long long mask = (long long)field->mask & 0x00000000ffffffff;
+
+	return (val << __bf_shf(mask)) & field->mask;
+}
+
+/**
+ * aie_get_reg_field() - get value from a field from a register valuer
+ * @field: a field in a register
+ * @regval: register value
+ * @return: value of a register field
+ */
+static inline u32 aie_get_reg_field(const struct aie_single_reg_field *field,
+				    u32 regval)
+{
+	long long mask64 = (long long)field->mask & 0x00000000ffffffff;
+
+	return (regval & field->mask) >> __bf_shf(mask64);
+}
+
+/**
+ * aie_cal_regoff() - calculate register offset to the whole AI engine
+ *		      device start address
+ * @adev: AI engine device
+ * @loc: AI engine tile location
+ * @regoff_intile: register offset within a tile
+ * @return: register offset to the whole AI engine device start address
+ */
+static inline u32 aie_cal_regoff(struct aie_device *adev,
+				 struct aie_location loc, u32 regoff_intile)
+{
+	return regoff_intile + (loc.col << adev->col_shift) +
+	       (loc.row << adev->row_shift);
+}
+
+/**
+ * aie_aperture_cal_regoff() - calculate register offset to the whole AI engine
+ *                             device start address
+ * @aperture: AI aperture
+ * @loc: AI engine tile location
+ * @regoff_intile: register offset within a tile
+ * @return: register offset to the whole AI engine device start address
+ */
+static inline u32 aie_aperture_cal_regoff(struct aie_aperture *aperture,
+					  struct aie_location loc,
+					  u32 regoff_intile)
+{
+	struct aie_device *adev = aperture->adev;
+
+	return regoff_intile + ((loc.col - aperture->range.start.col) <<
+				adev->col_shift) + (loc.row << adev->row_shift);
+}
+
+/**
+ * aie_validate_location() - validate tile location within an AI engine
+ *			     partition
+ * @apart: AI engine partition
+ * @loc: AI engine tile location relative in partition
+ * @return: return 0 if it is valid, negative value for errors.
+ *
+ * This function checks if the AI engine location is within the AI engine
+ * partition.
+ */
+static inline int aie_validate_location(struct aie_partition *apart,
+					struct aie_location loc)
+{
+	if (loc.col >= apart->range.size.col ||
+	    loc.row >= apart->range.size.row)
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * aie_resource_or_get_valueul() - get unsigned long value of specified
+ *				   number of bits starting from specified
+ *				   start bit of a resource bitmap
+ *
+ * @res: pointer to AI engine resource
+ * @sbit: start bit for OR operation
+ * @nbits: number of bits to OR
+ * @return: or result of @nbits of two bitmaps starting from @sbit
+ *
+ * OR @nbits of two resource bitmaps starting from @sbit
+ */
+static inline
+unsigned long aie_resource_or_get_valueul(struct aie_resource *res,
+					  u32 sbit, u32 nbits)
+{
+	const size_t i = BIT_WORD(sbit);
+	unsigned long bits;
+
+	bits = res->bitmap[i];
+	bits >>= (sbit % BITS_PER_LONG);
+	bits |= BITMAP_FIRST_WORD_MASK(nbits);
+
+	return bits;
+}
+
+int aie_resource_initialize(struct aie_resource *res, int count);
+void aie_resource_uninitialize(struct aie_resource *res);
+int aie_resource_check_region(struct aie_resource *res, u32 start,
+			      u32 count);
+int aie_resource_get_region(struct aie_resource *res, u32 start,
+			    u32 count);
+void aie_resource_put_region(struct aie_resource *res, int start, u32 count);
+int aie_resource_set(struct aie_resource *res, u32 start, u32 count);
+int aie_resource_cpy_from_arr32(struct aie_resource *res, u32 start,
+				const u32 *src, u32 nbits);
+int aie_resource_cpy_to_arr32(struct aie_resource *res, u32 start, u32 *dst,
+			      u32 nbits);
+int aie_resource_clear(struct aie_resource *res, u32 start, u32 count);
+int aie_resource_clear_all(struct aie_resource *res);
+bool aie_resource_testbit(struct aie_resource *res, u32 bit);
+int aie_resource_check_common_avail(struct aie_resource *res0,
+				    struct aie_resource *res1,
+				    u32 sbit, u32 nbits);
+int aie_resource_get_common_avail(struct aie_resource *res0,
+				  struct aie_resource *res1,
+				  u32 sbit, u32 nbits, u32 total,
+				  struct aie_rsc *rscs);
+int aie_resource_check_pattern_region(struct aie_resource *res,
+				      u32 start, u32 end, u32 count);
+int aie_resource_check_common_pattern_region(struct aie_resource *res0,
+					     struct aie_resource *res1,
+					     u32 sbit, u32 nbits, u32 total);
+int aie_resource_get_common_pattern_region(struct aie_resource *res0,
+					   struct aie_resource *res1,
+					   u32 sbit, u32 nbits, u32 total,
+					   struct aie_rsc *rscs);
+
+const struct file_operations *aie_part_get_fops(void);
+u8 aie_part_in_use(struct aie_partition *apart);
+struct aie_partition *aie_get_partition_from_id(struct aie_device *adev,
+						u32 partition_id);
+void of_xilinx_ai_engine_aperture_probe(struct aie_device *adev);
+struct aie_device *of_ai_engine_class_find(struct device_node *np);
+int xilinx_ai_engine_add_dev(struct aie_device *adev,
+			     struct platform_device *pdev);
+int xilinx_ai_engine_probe_v1(struct platform_device *pdev);
+
+void aie_part_remove(struct aie_partition *apart);
+int aie_part_clean(struct aie_partition *apart);
+int aie_part_open(struct aie_partition *apart, void *rsc_metadata);
+
+int aie_mem_get_info(struct aie_partition *apart, unsigned long arg);
+
+long aie_part_attach_dmabuf_req(struct aie_partition *apart,
+				void __user *user_args);
+long aie_part_detach_dmabuf_req(struct aie_partition *apart,
+				void __user *user_args);
+long aie_part_set_bd(struct aie_partition *apart, void __user *user_args);
+long aie_part_set_dmabuf_bd(struct aie_partition *apart,
+			    void __user *user_args);
+void aie_part_release_dmabufs(struct aie_partition *apart);
+int aie_part_prealloc_dbufs_cache(struct aie_partition *apart);
+
+int aie_part_scan_clk_state(struct aie_partition *apart);
+bool aie_part_check_clk_enable_loc(struct aie_partition *apart,
+				   struct aie_location *loc);
+int aie_part_set_freq(struct aie_partition *apart, u64 freq);
+int aie_part_get_freq(struct aie_partition *apart, u64 *freq);
+
+int aie_part_request_tiles_from_user(struct aie_partition *apart,
+				     void __user *user_args);
+int aie_part_release_tiles_from_user(struct aie_partition *apart,
+				     void __user *user_args);
+int aie_device_init(struct aie_device *adev);
+int aieml_device_init(struct aie_device *adev);
+
+bool aie_part_has_mem_mmapped(struct aie_partition *apart);
+bool aie_part_has_regs_mmapped(struct aie_partition *apart);
+
+int aie_part_get_tile_rows(struct aie_partition *apart,
+			   enum aie_tile_type ttype);
+
+int aie_part_reset(struct aie_partition *apart);
+int aie_part_post_reinit(struct aie_partition *apart);
+struct aie_partition *aie_create_partition(struct aie_aperture *aperture,
+					   u32 partition_id);
+
+void aie_aperture_backtrack(struct work_struct *work);
+irqreturn_t aie_interrupt(int irq, void *data);
+int aie_aperture_create_l2_bitmap(struct aie_aperture *aperture);
+bool aie_part_has_error(struct aie_partition *apart);
+void aie_part_clear_cached_events(struct aie_partition *apart);
+int aie_part_set_intr_rscs(struct aie_partition *apart);
+
+struct aie_aperture *
+of_aie_aperture_probe(struct aie_device *adev, struct device_node *nc);
+int aie_aperture_remove(struct aie_aperture *aperture);
+int aie_aperture_check_part_avail(struct aie_aperture *aperture,
+				  struct aie_partition_req *req);
+struct aie_partition *
+aie_aperture_request_part_from_id(struct aie_aperture *aperture,
+				  u32 partition_id);
+int aie_aperture_enquire_parts(struct aie_aperture *aperture,
+			       unsigned int num_queries,
+			       struct aie_range_args  *queries,
+			       int *num_parts_left, bool to_user);
+unsigned int aie_aperture_get_num_parts(struct aie_aperture *aperture);
+int aie_aperture_add_dev(struct aie_aperture *aperture,
+			 struct device_node *nc);
+
+int aie_part_rscmgr_init(struct aie_partition *apart);
+void aie_part_rscmgr_finish(struct aie_partition *apart);
+void aie_part_rscmgr_reset(struct aie_partition *apart);
+long aie_part_rscmgr_rsc_req(struct aie_partition *apart,
+			     void __user *user_args);
+long aie_part_rscmgr_rsc_release(struct aie_partition *apart,
+				 void __user *user_args);
+long aie_part_rscmgr_rsc_free(struct aie_partition *apart,
+			      void __user *user_args);
+long aie_part_rscmgr_rsc_req_specific(struct aie_partition *apart,
+				      void __user *user_args);
+long aie_part_rscmgr_rsc_check_avail(struct aie_partition *apart,
+				     void __user *user_args);
+long aie_part_rscmgr_get_broadcast(struct aie_partition *apart,
+				   void __user *user_args);
+int aie_part_rscmgr_set_static(struct aie_partition *apart, void *meta);
+int aie_part_rscmgr_set_tile_broadcast(struct aie_partition *apart,
+				       struct aie_location loc,
+				       enum aie_module_type mod, uint32_t id);
+
+int aie_part_sysfs_create_entries(struct aie_partition *apart);
+void aie_part_sysfs_remove_entries(struct aie_partition *apart);
+int aie_tile_sysfs_create_entries(struct aie_tile *atile);
+void aie_tile_sysfs_remove_entries(struct aie_tile *atile);
+ssize_t aie_sysfs_read_handler(struct file *filp, struct kobject *kobj,
+			       struct bin_attribute *attr, char *buf,
+			       loff_t offset, size_t max_size);
+
+ssize_t aie_sysfs_get_core_status(struct aie_partition *apart,
+				  struct aie_location *loc, char *buffer,
+				  ssize_t size);
+ssize_t aie_tile_show_core(struct device *dev, struct device_attribute *attr,
+			   char *buffer);
+ssize_t aie_part_read_cb_core(struct kobject *kobj, char *buffer, ssize_t size);
+ssize_t aie_sysfs_get_dma_status(struct aie_partition *apart,
+				 struct aie_location *loc, char *buffer,
+				 ssize_t size);
+ssize_t aie_tile_show_dma(struct device *dev, struct device_attribute *attr,
+			  char *buffer);
+ssize_t aie_part_read_cb_dma(struct kobject *kobj, char *buffer, ssize_t size);
+ssize_t aie_tile_show_lock(struct device *dev, struct device_attribute *attr,
+			   char *buffer);
+ssize_t aie_part_read_cb_lock(struct kobject *kobj, char *buffer, ssize_t size);
+ssize_t aie_sysfs_get_lock_status(struct aie_partition *apart,
+				  struct aie_location *loc, char *buffer,
+				  ssize_t size);
+u32 aie_get_module_error_count(struct aie_partition *apart,
+			       struct aie_location loc,
+			       enum aie_module_type module,
+			       const struct aie_error_attr *err_attr);
+bool aie_check_error_bitmap(struct aie_partition *apart,
+			    struct aie_location loc,
+			    enum aie_module_type module, u8 event);
+u32 aie_get_error_count(struct aie_partition *apart);
+ssize_t aie_sysfs_get_errors(struct aie_partition *apart,
+			     struct aie_location *loc, char *buffer,
+			     ssize_t size);
+ssize_t aie_tile_show_error(struct device *dev, struct device_attribute *attr,
+			    char *buffer);
+ssize_t aie_part_show_error_stat(struct device *dev,
+				 struct device_attribute *attr, char *buffer);
+ssize_t aie_part_show_current_freq(struct device *dev,
+				   struct device_attribute *attr, char *buffer);
+ssize_t aie_part_read_cb_error(struct kobject *kobj, char *buffer,
+			       ssize_t size);
+ssize_t aie_tile_show_event(struct device *dev, struct device_attribute *attr,
+			    char *buffer);
+void aie_read_event_status(struct aie_partition *apart,
+			   struct aie_location *loc,
+			   enum aie_module_type module, u32 *reg);
+ssize_t aie_part_read_cb_status(struct kobject *kobj, char *buffer,
+				ssize_t size);
+long aie_part_rscmgr_get_statistics(struct aie_partition *apart,
+				    void __user *user_args);
+
+int aie_overlay_register_notifier(void);
+void aie_overlay_unregister_notifier(void);
+#endif /* AIE_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-interrupt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-interrupt.c
@@ -0,0 +1,1456 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+#include <linux/bitmap.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+
+#include "ai-engine-internal.h"
+#include "linux/xlnx-ai-engine.h"
+
+#define AIE_ARRAY_TILE_ERROR_BC_ID		0U
+#define AIE_SHIM_TILE_ERROR_IRQ_ID		16U
+#define AIE_SHIM_INTR_BC_MAX			5U
+#define AIE_L2_MASK_REG_BITS			32U
+
+/**
+ * aie_get_broadcast_event() - get event ID being broadcast on given
+ *			       broadcast line.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @bc_id: broadcast ID.
+ * @return: event ID.
+ */
+static u8 aie_get_broadcast_event(struct aie_partition *apart,
+				  struct aie_location *loc,
+				  enum aie_module_type module, u8 bc_id)
+{
+	const struct aie_event_attr *event_mod;
+	u32 bcoff, regoff;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	bcoff = event_mod->bc_regoff + event_mod->bc_event.regoff + bc_id * 4U;
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, bcoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_read_event_status() - get the status of event status registers.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @reg: array to store event status register values.
+ */
+void aie_read_event_status(struct aie_partition *apart,
+			   struct aie_location *loc,
+			   enum aie_module_type module, u32 *reg)
+{
+	const struct aie_event_attr *event_mod;
+	u8 offset;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	for (offset = 0; offset < (event_mod->num_events / 32); offset++) {
+		u32 status_off = event_mod->status_regoff + offset * 4U;
+		u32 regoff = aie_aperture_cal_regoff(apart->aperture, *loc,
+						     status_off);
+
+		reg[offset] = ioread32(apart->aperture->base + regoff);
+	}
+}
+
+/**
+ * aie_clear_event_status() - clears the status of event.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @event: event ID.
+ */
+static void aie_clear_event_status(struct aie_partition *apart,
+				   struct aie_location *loc,
+				   enum aie_module_type module, u8 event)
+{
+	const struct aie_event_attr *event_mod;
+	u32 status_off, regoff;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	if (event >= event_mod->num_events)
+		return;
+
+	status_off = event_mod->status_regoff + (event / 32) * 4U;
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, status_off);
+	iowrite32(BIT(event % 32), apart->aperture->base + regoff);
+}
+
+/**
+ * aie_check_group_errors_enabled() - get error events enabled in group error.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @return: bitmap of enabled error events.
+ */
+static u32 aie_check_group_errors_enabled(struct aie_partition *apart,
+					  struct aie_location *loc,
+					  enum aie_module_type module)
+{
+	const struct aie_event_attr *event_mod;
+	u32 groff, regoff;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	groff = event_mod->group_regoff + event_mod->group_error.regoff;
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, groff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_set_error_event() - enable/disable error events in group error.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @bitmap: error event to enable/disable in group errors.
+ */
+static void aie_set_error_event(struct aie_partition *apart,
+				struct aie_location *loc,
+				enum aie_module_type module, u32 bitmap)
+{
+	const struct aie_event_attr *event_mod;
+	u32 groff, regoff;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	groff = event_mod->group_regoff + event_mod->group_error.regoff;
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, groff);
+	iowrite32(bitmap, apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_error_event() - map group error status bit to actual error
+ *			   event number.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @index: event index within group errors.
+ * @return: true event ID.
+ */
+static u32 aie_get_error_event(struct aie_partition *apart,
+			       struct aie_location *loc,
+			       enum aie_module_type module, u8 index)
+{
+	const struct aie_event_attr *event_mod;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	return event_mod->base_error_event + index;
+}
+
+/**
+ * aie_get_bc_event() - get the broadcast event ID.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @module: module type.
+ * @bc_id: broadcast line ID.
+ * @return: broadcast event ID.
+ */
+static u32 aie_get_bc_event(struct aie_partition *apart,
+			    struct aie_location *loc,
+			    enum aie_module_type module, u8 bc_id)
+{
+	const struct aie_event_attr *event_mod;
+
+	if (module == AIE_CORE_MOD)
+		event_mod = apart->adev->core_events;
+	else if (module == AIE_MEM_MOD)
+		event_mod = apart->adev->mem_events;
+	else
+		event_mod = apart->adev->pl_events;
+
+	return event_mod->base_bc_event + bc_id;
+}
+
+/**
+ * aie_get_l1_event() - get event ID being broadcast on level 1 IRQ.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @sw: switch type.
+ * @irq_id: IRQ event ID to be read.
+ * @return: true event ID.
+ */
+static u8 aie_get_l1_event(struct aie_partition *apart,
+			   struct aie_location *loc,
+			   enum aie_shim_switch_type sw, u8 irq_id)
+{
+	const struct aie_l1_intr_ctrl_attr *intr_ctrl = apart->adev->l1_ctrl;
+	u32 l1off, l1mask, regoff, reg_value;
+
+	if (sw == AIE_SHIM_SWITCH_A) {
+		l1off = intr_ctrl->regoff + intr_ctrl->swa_event.regoff;
+		l1mask = intr_ctrl->swa_event.mask;
+	} else {
+		l1off = intr_ctrl->regoff + intr_ctrl->swb_event.regoff;
+		l1mask = intr_ctrl->swb_event.mask;
+	}
+
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, l1off);
+	reg_value = ioread32(apart->aperture->base + regoff);
+	reg_value &= l1mask << (irq_id * intr_ctrl->event_lsb);
+	reg_value >>= (irq_id * intr_ctrl->event_lsb);
+	return reg_value;
+}
+
+/**
+ * aie_clear_l1_intr() - clear level 1 interrupt controller status.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @sw: switch type.
+ * @irq_id: IRQ ID to be cleared.
+ */
+static void aie_clear_l1_intr(struct aie_partition *apart,
+			      struct aie_location *loc,
+			      enum aie_shim_switch_type sw, u8 irq_id)
+{
+	const struct aie_l1_intr_ctrl_attr *intr_ctrl = apart->adev->l1_ctrl;
+	u32 l1off, regoff;
+
+	if (sw == AIE_SHIM_SWITCH_A)
+		l1off = intr_ctrl->regoff + intr_ctrl->swa_status.regoff;
+	else
+		l1off = intr_ctrl->regoff + intr_ctrl->swb_status.regoff;
+
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, l1off);
+	iowrite32(BIT(irq_id), apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_l1_status() - get level 1 interrupt controller status value.
+ * @apart: AIE partition pointer.
+ * @loc: pointer to tile location.
+ * @sw: switch type.
+ * @return: status value.
+ */
+static u32 aie_get_l1_status(struct aie_partition *apart,
+			     struct aie_location *loc,
+			     enum aie_shim_switch_type sw)
+{
+	const struct aie_l1_intr_ctrl_attr *intr_ctrl = apart->adev->l1_ctrl;
+	u32 l1off, regoff;
+
+	if (sw == AIE_SHIM_SWITCH_A)
+		l1off = intr_ctrl->regoff + intr_ctrl->swa_status.regoff;
+	else
+		l1off = intr_ctrl->regoff + intr_ctrl->swb_status.regoff;
+
+	regoff = aie_aperture_cal_regoff(apart->aperture, *loc, l1off);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_aperture_clear_l2_intr() - clear level 2 interrupt controller status.
+ * @aperture: AIE aperture pointer.
+ * @loc: pointer to tile location.
+ * @bitmap_irq: IRQ bitmap. IRQ lines corresponding to set bits will be
+ *		cleared.
+ */
+static void aie_aperture_clear_l2_intr(struct aie_aperture *aperture,
+				       struct aie_location *loc, u32 bitmap_irq)
+{
+	const struct aie_l2_intr_ctrl_attr *intr_ctrl = aperture->adev->l2_ctrl;
+	u32 l2off = intr_ctrl->regoff + intr_ctrl->status.regoff;
+	u32 regoff = aie_aperture_cal_regoff(aperture, *loc, l2off);
+
+	iowrite32(bitmap_irq, aperture->base + regoff);
+}
+
+/**
+ * aie_aperture_get_l2_status() - get level 2 interrupt controller status value.
+ * @aperture: AIE aperture pointer.
+ * @loc: pointer to tile location.
+ * @return: status value.
+ */
+static u32 aie_aperture_get_l2_status(struct aie_aperture *aperture,
+				      struct aie_location *loc)
+{
+	const struct aie_l2_intr_ctrl_attr *intr_ctrl = aperture->adev->l2_ctrl;
+	u32 l2off = intr_ctrl->regoff + intr_ctrl->status.regoff;
+	u32 regoff = aie_aperture_cal_regoff(aperture, *loc, l2off);
+
+	return ioread32(aperture->base + regoff);
+}
+
+/**
+ * aie_aperture_get_l2_mask() - get level 2 interrupt controller mask value.
+ * @aperture: AIE aperture pointer.
+ * @loc: pointer to tile location.
+ * @return: mask value.
+ */
+static u32 aie_aperture_get_l2_mask(struct aie_aperture *aperture,
+				    struct aie_location *loc)
+{
+	const struct aie_l2_intr_ctrl_attr *intr_ctrl = aperture->adev->l2_ctrl;
+	u32 l2off = intr_ctrl->regoff + intr_ctrl->mask.regoff;
+	u32 regoff = aie_aperture_cal_regoff(aperture, *loc, l2off);
+
+	return ioread32(aperture->base + regoff);
+}
+
+/**
+ * aie_aperture_enable_l2_ctrl() - enable interrupts to level 2 interrupt
+ *				   controller.
+ * @aperture: AIE aperture pointer.
+ * @loc: pointer to tile location.
+ * @bit_map: bitmap of broadcast lines to enable.
+ */
+static void aie_aperture_enable_l2_ctrl(struct aie_aperture *aperture,
+					struct aie_location *loc, u32 bit_map)
+{
+	const struct aie_l2_intr_ctrl_attr *intr_ctrl = aperture->adev->l2_ctrl;
+	u32 l2off = intr_ctrl->regoff + intr_ctrl->enable.regoff;
+	u32 regoff = aie_aperture_cal_regoff(aperture, *loc, l2off);
+
+	bit_map &= intr_ctrl->enable.mask;
+	iowrite32(bit_map, aperture->base + regoff);
+}
+
+/**
+ * aie_aperture_disable_l2_ctrl() - disable interrupts to level 2 interrupt
+ *				    controller.
+ * @aperture: AIE aperture pointer.
+ * @loc: pointer to tile location.
+ * @bit_map: bitmap of broadcast lines to disable.
+ */
+static void aie_aperture_disable_l2_ctrl(struct aie_aperture *aperture,
+					 struct aie_location *loc, u32 bit_map)
+{
+	const struct aie_l2_intr_ctrl_attr *intr_ctrl = aperture->adev->l2_ctrl;
+	u32 l2off = intr_ctrl->regoff + intr_ctrl->disable.regoff;
+	u32 regoff = aie_aperture_cal_regoff(aperture, *loc, l2off);
+
+	bit_map &= intr_ctrl->disable.mask;
+	iowrite32(bit_map, aperture->base + regoff);
+}
+
+/**
+ * aie_part_set_event_bitmap() - set the status of event in local event
+ *				 bitmap.
+ * @apart: AIE partition pointer.
+ * @loc: tile location.
+ * @module: module type.
+ * @event: event ID to be logged.
+ */
+static void aie_part_set_event_bitmap(struct aie_partition *apart,
+				      struct aie_location loc,
+				      enum aie_module_type module, u8 event)
+{
+	u8 row, col, mod_num_events;
+	struct aie_resource *event_sts;
+	u32 offset;
+
+	if (module == AIE_CORE_MOD) {
+		event_sts = &apart->core_event_status;
+		mod_num_events = apart->adev->core_events->num_events;
+		row = loc.row - apart->range.start.row - 1;
+	} else if (module == AIE_MEM_MOD) {
+		event_sts = &apart->mem_event_status;
+		mod_num_events = apart->adev->mem_events->num_events;
+		row = loc.row - apart->range.start.row - 1;
+	} else {
+		event_sts = &apart->pl_event_status;
+		mod_num_events = apart->adev->pl_events->num_events;
+		row = loc.row;
+	}
+
+	col = loc.col - apart->range.start.col;
+
+	offset = (col + row * apart->range.size.col) * mod_num_events + event;
+	aie_resource_set(event_sts, offset, 1);
+}
+
+/**
+ * aie_check_error_bitmap() - check the status of event in local event bitmap.
+ * @apart: AIE partition pointer.
+ * @loc: tile location.
+ * @module: module type.
+ * @event: event ID to check.
+ * @return: true if event has happened, else false.
+ */
+bool aie_check_error_bitmap(struct aie_partition *apart,
+			    struct aie_location loc,
+			    enum aie_module_type module, u8 event)
+{
+	struct aie_resource *event_sts;
+	u32 offset;
+	u8 row, col, mod_num_events;
+
+	if (module == AIE_CORE_MOD) {
+		event_sts = &apart->core_event_status;
+		mod_num_events = apart->adev->core_events->num_events;
+		row = loc.row - apart->range.start.row - 1;
+	} else if (module == AIE_MEM_MOD) {
+		event_sts = &apart->mem_event_status;
+		mod_num_events = apart->adev->mem_events->num_events;
+		row = loc.row - apart->range.start.row - 1;
+	} else {
+		event_sts = &apart->pl_event_status;
+		mod_num_events = apart->adev->pl_events->num_events;
+		row = loc.row;
+	}
+
+	col = loc.col - apart->range.start.col;
+
+	offset = (col + row * apart->range.size.col) * mod_num_events + event;
+	return aie_resource_testbit(event_sts, offset);
+}
+
+/**
+ * aie_tile_backtrack() - if error was asserted on a broadcast line in
+ *			  the given array tile,
+ *				* disable the error from the group errors
+ *				* record the error event in local bitmap
+ * @apart: AIE partition pointer.
+ * @loc: tile location.
+ * @module: module type.
+ * @sw: switch type.
+ * @bc_id: broadcast ID.
+ * @return: true if error was asserted, else return false.
+ */
+static bool aie_tile_backtrack(struct aie_partition *apart,
+			       struct aie_location loc,
+			       enum aie_module_type module,
+			       enum aie_shim_switch_type sw, u8 bc_id)
+{
+	unsigned long grenabled;
+	u32 status[4];
+	u8 n, grevent, eevent;
+	bool ret = false;
+
+	if (module == AIE_PL_MOD)
+		grevent = aie_get_l1_event(apart, &loc, sw, bc_id);
+	else
+		grevent = aie_get_broadcast_event(apart, &loc, module, bc_id);
+
+	aie_read_event_status(apart, &loc, module, status);
+
+	if (!(status[grevent / 32] & BIT(grevent % 32)))
+		return ret;
+
+	grenabled = aie_check_group_errors_enabled(apart, &loc, module);
+	for_each_set_bit(n, &grenabled, 32) {
+		eevent = aie_get_error_event(apart, &loc, module, n);
+		if (!(status[eevent / 32] & BIT(eevent % 32)))
+			continue;
+		grenabled &= ~BIT(n);
+		aie_part_set_event_bitmap(apart, loc, module, eevent);
+		ret = true;
+
+		dev_err_ratelimited(&apart->adev->dev,
+				    "Asserted tile error event %d at col %d row %d\n",
+				    eevent, loc.col, loc.row);
+	}
+	aie_set_error_event(apart, &loc, module, grenabled);
+
+	return ret;
+}
+
+/**
+ * aie_map_l2_to_l1() - map the status bit set in level 2 interrupt controller
+ *		        to a level 1 interrupt controller.
+ * @apart: AIE partition pointer.
+ * @set_pos: position of level 2 set bit.
+ * @l2_col: level 2 interrupt controller column ID.
+ * @l1_col: pointer to return corresponding level 1 column ID.
+ * @sw: pointer to return the level 1 interrupt controller switch ID.
+ *
+ * This API implementation is tightly coupled with the level 2 to level 1
+ * static mapping created when AIE application CDOs are generated.
+ */
+static void aie_map_l2_to_l1(struct aie_partition *apart, u32 set_pos,
+			     u32 l2_col, u32 *l1_col,
+			     enum aie_shim_switch_type *sw)
+{
+	if (l2_col + 3 >= apart->range.start.col + apart->range.size.col) {
+		*l1_col = l2_col + (set_pos % 6) / 2;
+		*sw = (set_pos % 6) % 2;
+	} else if (l2_col % 2 == 0) {
+		/* set bit position could be 0 - 5 */
+		*l1_col = l2_col - (2 - (set_pos % 6) / 2);
+		*sw = (set_pos % 6) % 2;
+	} else {
+		/* set bit position could be 0 - 1 */
+		*l1_col = l2_col;
+		*sw = set_pos;
+	}
+}
+
+/**
+ * aie_l1_backtrack() - backtrack AIE array tiles or shim tile based on
+ *			the level 2 status bit set.
+ * @apart: AIE partition pointer.
+ * @loc: tile location of level 2 interrupt controller.
+ * @set_pos: set bit position in level 2 controller status.
+ * @return: true if error was asserted, else return false.
+ */
+static bool aie_l1_backtrack(struct aie_partition *apart,
+			     struct aie_location loc, u32 set_pos)
+{
+	struct aie_location l1_ctrl;
+	enum aie_shim_switch_type sw;
+	u32 status;
+	u32 srow = apart->range.start.row + 1;
+	u32 erow = apart->range.start.row + apart->range.size.row;
+	bool ret = false;
+
+	/*
+	 * Based on the set status bit find which level 1 interrupt
+	 * controller has generated an interrupt
+	 */
+	l1_ctrl.row = 0;
+	aie_map_l2_to_l1(apart, set_pos, loc.col, &l1_ctrl.col, &sw);
+	/*
+	 * This should not be the case if the routing is generated based on
+	 * the partition. In case, the routing is generated with different
+	 * partition which is not likely, if doesn't have this checking, it
+	 * can access the tiles outside the partition.
+	 */
+	if (l1_ctrl.col >= (apart->range.start.col + apart->range.size.col))
+		return false;
+
+	status = aie_get_l1_status(apart, &l1_ctrl, sw);
+
+	/* For now, support error broadcasts only */
+	if (status & BIT(AIE_ARRAY_TILE_ERROR_BC_ID)) {
+		struct aie_location temp;
+		enum aie_module_type module;
+		u32 bc_event;
+
+		if (sw == AIE_SHIM_SWITCH_A)
+			module = AIE_CORE_MOD;
+		else
+			module = AIE_MEM_MOD;
+
+		aie_clear_l1_intr(apart, &l1_ctrl, sw,
+				  AIE_ARRAY_TILE_ERROR_BC_ID);
+
+		temp.row = srow;
+		temp.col = l1_ctrl.col;
+		bc_event = aie_get_bc_event(apart, &temp, module,
+					    AIE_ARRAY_TILE_ERROR_BC_ID);
+		for (; temp.row < erow; temp.row++) {
+			u32 reg[4];
+
+			if (!aie_part_check_clk_enable_loc(apart, &temp))
+				break;
+
+			if (aie_tile_backtrack(apart, temp, module, sw,
+					       AIE_ARRAY_TILE_ERROR_BC_ID))
+				ret = true;
+
+			aie_read_event_status(apart, &temp, module, reg);
+			if (!(reg[bc_event / 32] & BIT(bc_event % 32)))
+				break;
+
+			aie_clear_event_status(apart, &temp, module, bc_event);
+		}
+	}
+
+	if (status & BIT(AIE_SHIM_TILE_ERROR_IRQ_ID)) {
+		aie_clear_l1_intr(apart, &l1_ctrl, sw,
+				  AIE_SHIM_TILE_ERROR_IRQ_ID);
+		if (aie_tile_backtrack(apart, l1_ctrl, AIE_PL_MOD, sw,
+				       AIE_SHIM_TILE_ERROR_IRQ_ID))
+			ret = true;
+	}
+	return ret;
+}
+
+/**
+ * aie_range_get_num_nocs() - get number of shim NOC tiles of AI enigne range
+ * @range: AI engine tiles range pointer
+ * @aperture: AI engine aperture pointer
+ * @l2_bitmap_off: return l2 mask bitmap start offset of the range per 32bit
+ * @return: number of shim NOC tiles of the AI engine partition.
+ */
+static u32 aie_range_get_num_nocs(const struct aie_range *range,
+				  const struct aie_aperture *aperture,
+				  u32 *l2_bitmap_off)
+{
+	struct aie_location loc;
+	struct aie_device *adev = aperture->adev;
+	u32 num_nocs = 0;
+
+	for (loc.col = range->start.col, loc.row = 0;
+	     loc.col < range->start.col + range->size.col; loc.col++) {
+		u32 ttype;
+
+		ttype = adev->ops->get_tile_type(adev, &loc);
+		if (ttype != AIE_TILE_TYPE_SHIMNOC)
+			continue;
+		num_nocs++;
+	}
+
+	if (num_nocs && l2_bitmap_off) {
+		*l2_bitmap_off = 0;
+		for (loc.col = aperture->range.start.col, loc.row = 0;
+		     loc.col < range->start.col; loc.col++) {
+			u32 ttype;
+
+			ttype = adev->ops->get_tile_type(adev, &loc);
+			if (ttype != AIE_TILE_TYPE_SHIMNOC)
+				continue;
+			*l2_bitmap_off += 1;
+		}
+	}
+
+	return num_nocs;
+}
+
+/**
+ * aie_l2_backtrack() - iterate through each level 2 interrupt controller
+ *			in a given partition and backtrack its
+ *			corresponding level 1 interrupt controller.
+ * @apart: AIE partition pointer
+ */
+static void aie_l2_backtrack(struct aie_partition *apart)
+{
+	struct aie_aperture *aperture = apart->aperture;
+	struct aie_location loc;
+	u32 n, ttype, l2_bitmap_offset = 0, num_nocs;
+	int ret;
+	bool sched_work = false;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dev_err_ratelimited(&apart->dev,
+				    "Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return;
+	}
+
+	num_nocs = aie_range_get_num_nocs(&apart->range, aperture,
+					  &l2_bitmap_offset);
+	if (!num_nocs) {
+		mutex_unlock(&apart->mlock);
+		return;
+	}
+
+	for (loc.col = apart->range.start.col, loc.row = 0;
+	     loc.col < apart->range.start.col + apart->range.size.col;
+	     loc.col++) {
+		unsigned long l2_mask;
+		u32 adjust_l2_bitmap_offset = l2_bitmap_offset * 32;
+
+		ttype = apart->adev->ops->get_tile_type(apart->adev, &loc);
+		if (ttype != AIE_TILE_TYPE_SHIMNOC)
+			continue;
+
+		/*
+		 * copy to arr32 function requires bitmap is unsigned long
+		 * aligned.  For every 2nd l2 mask, it needs to include
+		 * the previous l2 mask status.
+		 */
+		if (l2_bitmap_offset % 2)
+			adjust_l2_bitmap_offset -= 32;
+		aie_resource_cpy_to_arr32(&aperture->l2_mask,
+					  adjust_l2_bitmap_offset,
+					  (u32 *)&l2_mask, 64);
+		if (l2_bitmap_offset % 2)
+			l2_mask >>= 32;
+		for_each_set_bit(n, &l2_mask,
+				 apart->adev->l2_ctrl->num_broadcasts) {
+			if (aie_l1_backtrack(apart, loc, n))
+				apart->error_to_report = 1;
+		}
+
+		/*
+		 * clear the l2 mask, it will be set when there is interrupt
+		 * coming from the NOC.
+		 */
+		aie_resource_clear(&aperture->l2_mask,
+				   l2_bitmap_offset *
+				   AIE_INTR_L2_CTRL_MASK_WIDTH,
+				   AIE_INTR_L2_CTRL_MASK_WIDTH);
+		l2_bitmap_offset++;
+		aie_aperture_enable_l2_ctrl(aperture, &loc, l2_mask);
+	}
+
+	/*
+	 * Level 2 interrupt registers are edge-triggered. As a result,
+	 * re-enabling level 2 won't trigger an interrupt for the already
+	 * latched interrupts at level 1 controller.
+	 */
+	for (loc.col = apart->range.start.col, loc.row = 0;
+	     loc.col < apart->range.start.col + apart->range.size.col;
+	     loc.col++) {
+		if (aie_get_l1_status(apart, &loc, AIE_SHIM_SWITCH_A) ||
+		    aie_get_l1_status(apart, &loc, AIE_SHIM_SWITCH_B)) {
+			mutex_unlock(&apart->mlock);
+			sched_work = true;
+			schedule_work(&apart->aperture->backtrack);
+			break;
+		}
+	}
+
+	if (!sched_work)
+		mutex_unlock(&apart->mlock);
+
+	/*
+	 * If error was asserted or there are errors pending to be reported to
+	 * the application, then invoke callback.
+	 */
+	if (apart->error_cb.cb && apart->error_to_report) {
+		apart->error_to_report = 0;
+		apart->error_cb.cb(apart->error_cb.priv);
+	}
+}
+
+/**
+ * aie_part_backtrack() - backtrack a individual.
+ * @apart: AIE partition pointer.
+ */
+static void aie_part_backtrack(struct aie_partition *apart)
+{
+	aie_l2_backtrack(apart);
+}
+
+/**
+ * aie_aperture_backtrack() - backtrack each partition to find the source of
+ *			      error interrupt.
+ * @work: pointer to the work structure.
+ *
+ * This task will re-enable IRQ after errors in all partitions has been
+ * serviced.
+ */
+void aie_aperture_backtrack(struct work_struct *work)
+{
+	struct aie_aperture *aperture;
+	struct aie_partition *apart;
+	int ret;
+
+	aperture = container_of(work, struct aie_aperture, backtrack);
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret) {
+		dev_err_ratelimited(&aperture->dev,
+				    "Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return;
+	}
+
+	list_for_each_entry(apart, &aperture->partitions, node) {
+		/*
+		 * If partition isn't requested yet, then only record the
+		 * occurrence of error interrupt. Such errors can only be
+		 * backtracked when the tiles in-use are known. Based on the
+		 * error_to_report value a task is scheduled in the workqueue
+		 * to backtrack this error interrupt when partition is
+		 * requested.
+		 */
+		if (!apart->status)
+			continue;
+		aie_part_backtrack(apart);
+	}
+
+	mutex_unlock(&aperture->mlock);
+}
+
+/**
+ * aie_interrupt() - interrupt handler for AIE.
+ * @irq: Interrupt number.
+ * @data: AI engine aperture structure.
+ * @return: IRQ_HANDLED.
+ *
+ * This thread function disables level 2 interrupt controllers and schedules a
+ * task in workqueue to backtrack the source of error interrupt. Disabled
+ * interrupts are re-enabled after successful completion of bottom half.
+ */
+irqreturn_t aie_interrupt(int irq, void *data)
+{
+	struct aie_aperture *aperture = data;
+	struct aie_device *adev = aperture->adev;
+	int ret;
+	u32 l2_bitmap_offset = 0;
+	struct aie_location loc;
+	bool sched_work = false;
+
+	for (loc.col = aperture->range.start.col, loc.row = 0;
+	     loc.col < aperture->range.start.col + aperture->range.size.col;
+	     loc.col++) {
+		unsigned long l2_mask_64;
+		u32 ttype, l2_status, l2_mask, nbits_cpy, adjust_l2_bitmap_off;
+
+		ttype = adev->ops->get_tile_type(adev, &loc);
+		if (ttype != AIE_TILE_TYPE_SHIMNOC)
+			continue;
+
+		l2_mask = aie_aperture_get_l2_mask(aperture, &loc);
+		if (l2_mask) {
+			adjust_l2_bitmap_off = l2_bitmap_offset * 32;
+			nbits_cpy = 32;
+			if (l2_bitmap_offset % 2) {
+				/*
+				 * copy from arr32 function requires
+				 * bitmap is unsigned long aligned.
+				 * for every 2nd l2 mask, it needs to include
+				 * the previous l2 mask status.
+				 */
+				aie_resource_cpy_from_arr32(&aperture->l2_mask,
+							    l2_bitmap_offset *
+							    32,
+							    (u32 *)&l2_mask_64,
+							    32);
+				l2_mask_64 |= (unsigned long)l2_mask << 32;
+				nbits_cpy = 64;
+				adjust_l2_bitmap_off -= 32;
+			} else {
+				l2_mask_64 = (unsigned long)l2_mask;
+			}
+			aie_resource_cpy_from_arr32(&aperture->l2_mask,
+						    adjust_l2_bitmap_off,
+						    (u32 *)&l2_mask_64,
+						    nbits_cpy);
+			aie_aperture_disable_l2_ctrl(aperture, &loc, l2_mask);
+		}
+
+		l2_status = aie_aperture_get_l2_status(aperture, &loc);
+		if (l2_status) {
+			aie_aperture_clear_l2_intr(aperture, &loc,
+						   l2_status);
+			sched_work = true;
+		} else {
+			aie_aperture_enable_l2_ctrl(aperture, &loc,
+						    l2_mask);
+		}
+		l2_bitmap_offset++;
+	}
+
+	/* For ES1 silicon, interrupts are latched in NPI */
+	if (aperture->adev->version == VERSAL_ES1_REV_ID) {
+		ret = zynqmp_pm_clear_aie_npi_isr(aperture->adev->pm_node_id,
+						  AIE_NPI_ERROR_ID);
+		if (ret < 0)
+			dev_err(&aperture->dev, "Failed to clear NPI ISR\n");
+	}
+
+	if (sched_work)
+		schedule_work(&aperture->backtrack);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * aie_part_has_error() - check if AI engine partition has errors raised
+ * @apart: AIE partition pointer
+ * @return: true if AI engine partition has errors, false otherwise.
+ *
+ * This function checkes the aperture struct @l2_mask field, this field will
+ * be set when there is error interrupt generated from the SHIM NOC, and it
+ * will be cleared in the partition errors backtrack. And thus, if it is set
+ * it means there is error raised from the partition and backtrack is not done
+ * yet.
+ * It will request the aperture lock. Caller needs to make sure aperture lock
+ * is released before calling this function.
+ */
+bool aie_part_has_error(struct aie_partition *apart)
+{
+	struct aie_aperture *aperture = apart->aperture;
+	int ret;
+	u32 l2_bitmap_off, num_nocs;
+
+	/*
+	 * TODO: errors backtracking is not support for AIEML. for now, return
+	 * false based on device generation.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_dbg(&apart->dev, "Skipping error backtracking.\n");
+		return false;
+	}
+	num_nocs = aie_range_get_num_nocs(&apart->range, aperture,
+					  &l2_bitmap_off);
+	if (!num_nocs)
+		return false;
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return false;
+	}
+
+	ret = aie_resource_check_region(&aperture->l2_mask,
+					l2_bitmap_off *
+					AIE_INTR_L2_CTRL_MASK_WIDTH,
+					num_nocs * AIE_INTR_L2_CTRL_MASK_WIDTH);
+	mutex_unlock(&aperture->mlock);
+
+	if (ret != ((int)l2_bitmap_off * AIE_INTR_L2_CTRL_MASK_WIDTH)) {
+		/* There is error from this partition */
+		return true;
+	}
+
+	return false;
+}
+
+/**
+ * aie_aperture_create_l2_bitmap() - create bitmaps to record mask and status
+ *				     values for level 2 interrupt controllers.
+ * @aperture: AI engine aperture
+ * @return: 0 for success, and negative value for failure.
+ */
+int aie_aperture_create_l2_bitmap(struct aie_aperture *aperture)
+{
+	int ret;
+	u32 num_nocs;
+
+	num_nocs = aie_range_get_num_nocs(&aperture->range, aperture, NULL);
+	if (!num_nocs)
+		return 0;
+
+	ret = aie_resource_initialize(&aperture->l2_mask, num_nocs *
+				      AIE_INTR_L2_CTRL_MASK_WIDTH);
+
+	return ret;
+}
+
+/**
+ * aie_get_module_error_count() - get the total count of errors in a module
+ *				  from local bitmap.
+ * @apart: AIE partition pointer.
+ * @loc: tile location.
+ * @module: module type.
+ * @err_attr: error attribute for given module type.
+ * @return: total number of errors found.
+ */
+u32 aie_get_module_error_count(struct aie_partition *apart,
+			       struct aie_location loc,
+			       enum aie_module_type module,
+			       const struct aie_error_attr *err_attr)
+{
+	u32 count = 0;
+	u8 i, j;
+
+	for (i = 0; i < err_attr->num_err_categories; i++) {
+		for (j = 0; j < err_attr->err_category[i].num_events; j++) {
+			u8 event = err_attr->err_category[i].prop[j].event;
+
+			if (aie_check_error_bitmap(apart, loc, module, event))
+				count++;
+		}
+	}
+	return count;
+}
+
+/**
+ * aie_get_error_count() - get the total count of errors in a partition from
+ *			   local bitmap.
+ * @apart: AIE partition pointer.
+ * @return: total number of errors found.
+ */
+u32 aie_get_error_count(struct aie_partition *apart)
+{
+	const struct aie_error_attr *core_errs = apart->adev->core_errors;
+	const struct aie_error_attr *mem_errs = apart->adev->mem_errors;
+	const struct aie_error_attr *shim_errs = apart->adev->shim_errors;
+	struct aie_location loc;
+	u32 ttype, num = 0;
+
+	for (loc.col = apart->range.start.col;
+	     loc.col < apart->range.start.col + apart->range.size.col;
+	     loc.col++) {
+		for (loc.row = apart->range.start.row;
+		     loc.row < apart->range.size.row; loc.row++) {
+			ttype = apart->adev->ops->get_tile_type(apart->adev,
+								&loc);
+			if (ttype == AIE_TILE_TYPE_TILE) {
+				num += aie_get_module_error_count(apart, loc,
+								  AIE_CORE_MOD,
+								  core_errs);
+				num += aie_get_module_error_count(apart, loc,
+								  AIE_MEM_MOD,
+								  mem_errs);
+			} else {
+				num += aie_get_module_error_count(apart, loc,
+								  AIE_PL_MOD,
+								  shim_errs);
+			}
+		}
+	}
+
+	return num;
+}
+
+/**
+ * aie_get_errors_from_bitmap() - get status of errors from local bitmap.
+ * @apart: AIE partition pointer.
+ * @loc: tile location.
+ * @module: module type.
+ * @err_attr: error attribute for given module type.
+ * @aie_err: pointer to array of error structure.
+ * @return: total number of errors found.
+ *
+ * This function parses local bitmaps and initializes @aie_err structures with
+ * the tile location of error event, module type and, its event ID.
+ */
+static u32 aie_get_errors_from_bitmap(struct aie_partition *apart,
+				      struct aie_location loc,
+				      enum aie_module_type module,
+				      const struct aie_error_attr *err_attr,
+				      struct aie_error *aie_err)
+{
+	u8 i, j;
+	u32 num_err = 0;
+
+	for (i = 0; i < err_attr->num_err_categories; i++) {
+		const struct aie_err_category *category;
+
+		category = &err_attr->err_category[i];
+		for (j = 0; j < category->num_events; j++) {
+			u8 event = category->prop[j].event;
+
+			if (!aie_check_error_bitmap(apart, loc, module, event))
+				continue;
+
+			aie_err[num_err].loc.col = loc.col;
+			aie_err[num_err].loc.row = loc.row;
+			aie_err[num_err].module = module;
+			aie_err[num_err].error_id = event;
+			aie_err[num_err].category = category->err_category;
+			num_err++;
+		}
+	}
+	return num_err;
+}
+
+/**
+ * aie_get_module_errors() - get errors for a given module type
+ *			     in a partition.
+ * @apart: AIE partition pointer.
+ * @module: module type.
+ * @aie_err: pointer to array of error structure.
+ * @return: total number of errors found.
+ *
+ * This function parses local bitmaps and initializes @aie_err structures.
+ */
+static u32 aie_get_module_errors(struct aie_partition *apart,
+				 enum aie_module_type module,
+				 struct aie_error *aie_err)
+{
+	const struct aie_error_attr *err_attr;
+	struct aie_location loc;
+	u32 srow, erow, scol, ecol, num_err = 0;
+
+	if (module == AIE_CORE_MOD) {
+		err_attr = apart->adev->core_errors;
+		srow = apart->range.start.row + 1;
+		erow = srow + apart->range.size.row - 1;
+	} else if (module == AIE_MEM_MOD) {
+		err_attr = apart->adev->mem_errors;
+		srow = apart->range.start.row + 1;
+		erow = srow + apart->range.size.row - 1;
+	} else {
+		err_attr = apart->adev->shim_errors;
+		srow = 0;
+		erow = 0;
+	}
+
+	scol = apart->range.start.col;
+	ecol = apart->range.start.col + apart->range.size.col - 1;
+
+	for (loc.col = scol; loc.col <= ecol; loc.col++) {
+		for (loc.row = srow; loc.row <= erow; loc.row++) {
+			num_err +=
+				aie_get_errors_from_bitmap(apart, loc,
+							   module, err_attr,
+							   &aie_err[num_err]);
+		}
+	}
+	return num_err;
+}
+
+/**
+ * aie_part_clear_cached_events() - clear cached events in a partition.
+ * @apart: AIE partition pointer
+ *
+ * This function will clear the cached events in a partition.
+ */
+void aie_part_clear_cached_events(struct aie_partition *apart)
+{
+	aie_resource_clear_all(&apart->core_event_status);
+	aie_resource_clear_all(&apart->mem_event_status);
+	aie_resource_clear_all(&apart->pl_event_status);
+}
+
+/**
+ * aie_part_set_intr_rscs() - set broadcast resources used by interrupt
+ * @apart: AIE partition pointer
+ * @return: 0 for sueccess, and negative value for failure
+ *
+ * This function reserves interrupt broadcast channels resources.
+ */
+int aie_part_set_intr_rscs(struct aie_partition *apart)
+{
+	u32 c, r;
+	int ret;
+
+	for (c = 0; c < apart->range.size.col; c++) {
+		u32 b;
+		struct aie_location l = {
+			.col = apart->range.start.col + c,
+			.row = 0,
+		};
+
+		/* reserved broadcast channels 0 - 5 for SHIM */
+		for (b = 0; b <= AIE_SHIM_INTR_BC_MAX; b++) {
+			ret = aie_part_rscmgr_set_tile_broadcast(apart, l,
+								 AIE_PL_MOD,
+								 b);
+			if (ret)
+				return ret;
+		}
+
+		for (r = 1; r < apart->range.size.row; r++) {
+			struct aie_device *adev = apart->adev;
+			struct aie_tile_attr *tattr;
+			u32 m, ttype;
+
+			b = AIE_ARRAY_TILE_ERROR_BC_ID;
+			l.row = apart->range.start.row + r;
+			ttype = adev->ops->get_tile_type(apart->adev, &l);
+
+			if (WARN_ON(ttype >= AIE_TILE_TYPE_MAX))
+				return -EINVAL;
+
+			tattr = &adev->ttype_attr[ttype];
+			for (m = 0; m < tattr->num_mods; m++) {
+				enum aie_module_type mod = tattr->mods[m];
+
+				ret = aie_part_rscmgr_set_tile_broadcast(apart,
+									 l, mod,
+									 b);
+				if (ret)
+					return ret;
+			}
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * aie_register_error_notification() - register a callback for error
+ *				       notification.
+ * @dev: AIE partition device.
+ * @cb: pointer to a function that accepts pointer to private data as an
+ *	argument. callbacks are called in the bottom half without locks.
+ * @priv: private data to be passed to the callback.
+ * @return: 0 for success, and negative value for failure.
+ */
+int aie_register_error_notification(struct device *dev,
+				    void (*cb)(void *priv), void *priv)
+{
+	struct aie_partition *apart;
+	int ret;
+
+	if (!cb || !dev)
+		return -EINVAL;
+
+	apart = container_of(dev, struct aie_partition, dev);
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_err(&apart->dev,
+			"error handling is not supported for aieml device\n");
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return ret;
+	}
+
+	if (apart->error_cb.cb) {
+		dev_err(&apart->dev,
+			"Error callback already registered. Unregister the existing callback to register a new one.\n");
+		ret = -EINVAL;
+		goto exit;
+	}
+
+	apart->error_cb.cb = cb;
+	apart->error_cb.priv = priv;
+
+	/*
+	 * Errors during configuration are logged even for the partitions
+	 * which are not requested. Such errors must be reported back to the
+	 * application when a valid callback is registered.
+	 */
+	if (apart->error_to_report) {
+		mutex_unlock(&apart->mlock);
+		schedule_work(&apart->aperture->backtrack);
+		return ret;
+	}
+
+exit:
+	mutex_unlock(&apart->mlock);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(aie_register_error_notification);
+
+/**
+ * aie_unregister_error_notification() - Unregister the callback for error
+ *					 notification.
+ * @dev: AIE partition device.
+ * @return: 0 for success, and negative value for failure.
+ */
+int aie_unregister_error_notification(struct device *dev)
+{
+	struct aie_partition *apart;
+	int ret;
+
+	if (!dev)
+		return -EINVAL;
+
+	apart = container_of(dev, struct aie_partition, dev);
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_err(&apart->dev,
+			"error handling is not supported for aieml device\n");
+		return -EINVAL;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return ret;
+	}
+
+	apart->error_cb.cb = NULL;
+	apart->error_cb.priv = NULL;
+
+	mutex_unlock(&apart->mlock);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(aie_unregister_error_notification);
+
+/**
+ * aie_get_errors() - get errors that has happened.
+ * @dev: AIE partition device.
+ * @return: struct pointer of type aie_errors.
+ *
+ * This API allocates and initializes data structures by parsing local
+ * bitmaps. Allocated data structure must be deallocated using
+ * aie_free_errors() function.
+ */
+struct aie_errors *aie_get_errors(struct device *dev)
+{
+	struct aie_partition *apart;
+	struct aie_errors *aie_errs;
+	struct aie_error *error;
+	u32 num_errs, count = 0;
+	int ret;
+
+	if (!dev)
+		return ERR_PTR(-EINVAL);
+
+	apart = container_of(dev, struct aie_partition, dev);
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_err(&apart->dev,
+			"error handling is not supported for aieml device\n");
+		return NULL;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return ERR_PTR(ret);
+	}
+
+	num_errs = aie_get_error_count(apart);
+	if (!num_errs) {
+		mutex_unlock(&apart->mlock);
+		return NULL;
+	}
+
+	aie_errs = kzalloc(sizeof(*aie_errs), GFP_KERNEL);
+	if (!aie_errs) {
+		mutex_unlock(&apart->mlock);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	error = kcalloc(num_errs, sizeof(*error), GFP_KERNEL);
+	if (!error) {
+		kfree(aie_errs);
+		mutex_unlock(&apart->mlock);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	count += aie_get_module_errors(apart, AIE_MEM_MOD, &error[count]);
+	count += aie_get_module_errors(apart, AIE_CORE_MOD, &error[count]);
+	count += aie_get_module_errors(apart, AIE_PL_MOD, &error[count]);
+
+	aie_errs->dev = dev;
+	aie_errs->errors = error;
+	aie_errs->num_err = count;
+
+	mutex_unlock(&apart->mlock);
+	return aie_errs;
+}
+EXPORT_SYMBOL_GPL(aie_get_errors);
+
+/**
+ * aie_get_error_categories() - Get the error categories. Error information
+ *				returned by aie_get_errors() could be
+ *				abstracted by classifying errors into various
+ *				categories. All DMA channel error are
+ *				classified as AIE_ERROR_CATEGORY_DMA, program
+ *				and data memory ECC errors are classified as
+ *				AIE_ERROR_CATEGORY_ECC, and so on.
+ * @aie_errs: AIE errors structure.
+ * @return: Bitmap of category of error events.
+ */
+u32 aie_get_error_categories(struct aie_errors *aie_errs)
+{
+	u32 e, ret = 0;
+
+	if (!aie_errs || !aie_errs->errors)
+		return 0;
+
+	for (e = 0; e < aie_errs->num_err; e++) {
+		struct aie_error *error = &aie_errs->errors[e];
+
+		ret |= BIT(error->category);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(aie_get_error_categories);
+
+/**
+ * aie_get_error_string() - get error string corresponding an error.
+ * @aie_errs: pointer to an array of error structure.
+ * @aie_err: AIE error.
+ * @return: string corresponding to @aie_err.
+ */
+const char *aie_get_error_string(struct aie_errors *aie_errs,
+				 struct aie_error *aie_err)
+{
+	struct aie_partition *apart;
+	const struct aie_error_attr *err_attr;
+	u8 i, j;
+	int ret;
+
+	if (!aie_errs || !aie_errs->dev || !aie_err)
+		return ERR_PTR(-EINVAL);
+
+	apart = container_of(aie_errs->dev, struct aie_partition, dev);
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_err(&apart->dev,
+			"error handling is not supported for aieml device\n");
+		return NULL;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return ERR_PTR(ret);
+	}
+
+	if (aie_err->module == AIE_CORE_MOD)
+		err_attr = apart->adev->core_errors;
+	else if (aie_err->module == AIE_MEM_MOD)
+		err_attr = apart->adev->mem_errors;
+	else
+		err_attr = apart->adev->shim_errors;
+
+	for (i = 0; i < err_attr->num_err_categories; i++) {
+		for (j = 0; j < err_attr->err_category[i].num_events; j++) {
+			u8 event = err_attr->err_category[i].prop[j].event;
+
+			if (event != aie_err->error_id)
+				continue;
+
+			mutex_unlock(&apart->mlock);
+			return err_attr->err_category[i].prop[j].event_str;
+		}
+	}
+
+	mutex_unlock(&apart->mlock);
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(aie_get_error_string);
+
+/**
+ * aie_flush_errors() - Flush all pending errors.
+ * @dev: AIE partition device.
+ * @return: 0 for success, and negative value for failure.
+ *
+ * This function backtracks a given partition, updates local event status
+ * bitmaps and, invokes the registered callback function for any error event.
+ */
+int aie_flush_errors(struct device *dev)
+{
+	struct aie_partition *apart;
+
+	if (!dev)
+		return -EINVAL;
+
+	apart = container_of(dev, struct aie_partition, dev);
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_err(&apart->dev,
+			"error handling is not supported for aieml device\n");
+		return -EINVAL;
+	}
+	aie_part_backtrack(apart);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(aie_flush_errors);
+
+/**
+ * aie_free_errors() - Free allocated AIE error structure.
+ * @aie_errs: AIE error structure.
+ */
+void aie_free_errors(struct aie_errors *aie_errs)
+{
+	if (!aie_errs || !aie_errs->errors)
+		return;
+
+	kfree(aie_errs->errors);
+	kfree(aie_errs);
+}
+EXPORT_SYMBOL_GPL(aie_free_errors);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-mem.c
@@ -0,0 +1,303 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device memory implementation
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/dma-buf.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+#include <uapi/linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+#define aie_cal_reg_goffset(adev, loc, regoff) ({ \
+	struct aie_device *_adev = (adev); \
+	struct aie_location *_loc = &(loc); \
+	(_loc->col << _adev->col_shift) + \
+	(_loc->row << _adev->row_shift) + (regoff); \
+	})
+
+#define aie_cal_reg_pa(aperture, rloc, regoff) ({ \
+	struct aie_aperture *__aperture = (aperture); \
+	__aperture->res.start + aie_cal_reg_goffset(__aperture->adev, rloc, \
+						    regoff); \
+	})
+
+static struct sg_table *
+aie_mem_map_dma_buf(struct dma_buf_attachment *attachment,
+		    enum dma_data_direction direction)
+{
+	/*
+	 * TODO: It is mandatory by DMA buf operation. It is used return
+	 * scatterlist table of an attachment. We don't have the implementation
+	 * for now. And thus it has empty implementation.
+	 */
+	(void)attachment;
+	(void)direction;
+	dev_warn(attachment->dev,
+		 "AI engine memory map dma buf is not implemented.\n");
+	return NULL;
+}
+
+static void aie_mem_unmap_dma_buf(struct dma_buf_attachment *attachment,
+				  struct sg_table *table,
+				  enum dma_data_direction direction)
+{
+	/*
+	 * TODO: It is mandatory by DMA buf operation. It is used deallocate
+	 * scatterlist table of an attachment. We don't have the implementation
+	 * for now. And thus it has empty implementation.
+	 */
+	(void)attachment;
+	(void)table;
+	(void)direction;
+	dev_warn(attachment->dev,
+		 "AI engine memory unmap dma buf is not implemented.\n");
+}
+
+static int aie_mem_mmap(struct dma_buf *dmabuf, struct vm_area_struct *vma)
+{
+	struct aie_part_mem *pmem = dmabuf->priv;
+	struct aie_mem *mem = &pmem->mem;
+	struct aie_partition *apart = pmem->apart;
+	struct aie_aperture *aperture = apart->aperture;
+	struct aie_location rloc;
+	unsigned long addr = vma->vm_start;
+	unsigned long offset = vma->vm_pgoff * PAGE_SIZE, moffset = 0;
+	unsigned long remainder = vma->vm_end - addr;
+	size_t msize = mem->size;
+	u32 rstart_col = mem->range.start.col - aperture->range.start.col;
+
+	if (remainder + offset > pmem->size)
+		return -EINVAL;
+
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	for (rloc.col = rstart_col;
+	     rloc.col < rstart_col + mem->range.size.col; rloc.col++) {
+		for (rloc.row = mem->range.start.row;
+		     rloc.row < mem->range.start.row + mem->range.size.row;
+		     rloc.row++) {
+			unsigned long toffset, len;
+			phys_addr_t mempa;
+			int ret;
+
+			remainder = vma->vm_end - addr;
+			if (!remainder)
+				return 0;
+
+			if (moffset + msize < offset) {
+				moffset += msize;
+				continue;
+			}
+			/*
+			 * calculate offset within the tile memory.
+			 * offset is the offset to vma->start.
+			 * moffset is the tile memory start offset to
+			 * vma->start.
+			 */
+			toffset = offset - moffset;
+			len = msize - toffset;
+			if (len > remainder)
+				len = remainder;
+			mempa = aie_cal_reg_pa(apart->aperture, rloc,
+					       toffset + mem->offset);
+
+			ret = remap_pfn_range(vma, addr, mempa >> PAGE_SHIFT,
+					      len, vma->vm_page_prot);
+			if (ret) {
+				dev_err(&apart->dev,
+					"failed to mmap (%u,%u)memory, remap failed, 0x%pa, 0x%lx.\n",
+					(rloc.col + aperture->range.start.col),
+					rloc.row, &mempa, len);
+				return ret;
+			}
+			addr += len;
+			offset += len;
+			moffset += msize;
+		}
+	}
+	return 0;
+}
+
+static void aie_mem_dmabuf_release(struct dma_buf *dmabuf)
+{
+	struct aie_part_mem *pmem = dmabuf->priv;
+
+	pmem->dbuf = NULL;
+}
+
+static const struct dma_buf_ops aie_mem_dma_buf_ops = {
+	.map_dma_buf = aie_mem_map_dma_buf,
+	.unmap_dma_buf = aie_mem_unmap_dma_buf,
+	.mmap = aie_mem_mmap,
+	.release = aie_mem_dmabuf_release,
+};
+
+/**
+ * aie_mem_create_dmabuf() - creates DMA buffer for AI engine partition
+ *			     memories
+ * @apart: AI engine partition
+ * @pmem: pointer to the partition memory information
+ * @mem: pointer to where it store the memory information and DMA buf file
+ *	 descriptor for user.
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will create DMA buffer for the AI engine partition memory
+ * and will store the DMA buffer file descriptor and memory information in
+ * @mem.
+ */
+static int aie_mem_create_dmabuf(struct aie_partition *apart,
+				 struct aie_part_mem *pmem,
+				 struct aie_mem *mem)
+{
+	struct dma_buf *dmabuf;
+	int ret;
+
+	if (!PAGE_ALIGNED(pmem->mem.size)) {
+		dev_warn(&apart->dev,
+			 "no dmabuf for mem(0x%zx, 0x%zx), not aligned with page size.\n",
+			 pmem->mem.offset, pmem->mem.size);
+		return -EINVAL;
+	}
+
+	dmabuf = pmem->dbuf;
+	if (!dmabuf) {
+		DEFINE_DMA_BUF_EXPORT_INFO(exp_info);
+
+		exp_info.ops = &aie_mem_dma_buf_ops;
+		exp_info.size = pmem->size;
+		exp_info.flags = O_RDWR;
+		exp_info.priv = pmem;
+
+		dmabuf = dma_buf_export(&exp_info);
+		if (IS_ERR(dmabuf))
+			return PTR_ERR(dmabuf);
+
+		pmem->dbuf = dmabuf;
+	}
+
+	ret = dma_buf_fd(dmabuf, O_CLOEXEC);
+	if (ret < 0) {
+		dev_err(&apart->dev,
+			"dmabuf creation failed, failed to get fd.\n");
+		return ret;
+	}
+	memcpy(mem, &pmem->mem, sizeof(*mem));
+	mem->fd = ret;
+
+	return 0;
+}
+
+/**
+ * aie_mem_get_info() - get AI engine memories information
+ * @apart: AI engine partition
+ * @arg: argument from user to enquire AI engine partition memory information
+ * @return: 0 for success, and negative value for failure
+ *
+ * This function will get the memories information for the specified AI engine
+ * partition. It will create DMA buf file descriptors for the memories and
+ * return the DMA buf file descriptors to users.
+ * It will create a DMA buffer per type of memories.
+ * e.g. There will be a DMA buffer for all the tile program memories in the
+ * partition, and another DMA buffer for all the tile data memories in the
+ * partition.
+ * User can first pass num_mems as 0 in the @arg to enquire for how many types
+ * of memories in this AI engine partition. And then, user can allocate memory
+ * to keep the information for different types of memories, and then use the
+ * same enqury with non-zero num_mems and none NULL pointer to ask for the
+ * details of the information of all the types of memories in the AI engine
+ * partition.
+ */
+int aie_mem_get_info(struct aie_partition *apart, unsigned long arg)
+{
+	struct aie_mem_args margs;
+	struct aie_mem *mems;
+	unsigned int num_mems, i;
+	int ret;
+
+	if (copy_from_user(&margs, (void __user *)arg, sizeof(margs)))
+		return -EFAULT;
+
+	num_mems = apart->adev->ops->get_mem_info(apart->adev, &apart->range,
+						  NULL);
+	if (num_mems <= 0)
+		return -EINVAL;
+
+	if (!margs.num_mems) {
+		struct aie_mem_args __user *umargs_ptr = (void __user *)arg;
+
+		/* This enquiry is to get the number of types of memories. */
+		if (copy_to_user((void __user *)&umargs_ptr->num_mems,
+				 &num_mems, sizeof(num_mems)))
+			return -EFAULT;
+		return 0;
+	}
+
+	if (num_mems != margs.num_mems) {
+		dev_err(&apart->dev,
+			"failed to get mem info, invalid num of mems %d,%d.\n",
+			num_mems, margs.num_mems);
+		return -EINVAL;
+	}
+	if (!margs.mems) {
+		dev_err(&apart->dev,
+			"failed to get mem info, mems pointer is NULL.\n");
+		return -EINVAL;
+	}
+
+	mems = kcalloc(num_mems, sizeof(*mems), GFP_KERNEL);
+	if (!mems)
+		return -ENOMEM;
+
+	/*
+	 * Create DMA buffer for the memories.
+	 * Each type of memory in the partition has its own DMA buf.
+	 */
+	for (i = 0; i < num_mems; i++) {
+		ret = aie_mem_create_dmabuf(apart, &apart->pmems[i], &mems[i]);
+		if (ret)
+			break;
+	}
+	if (!ret) {
+		if (copy_to_user((void __user *)margs.mems, mems,
+				 num_mems * sizeof(mems[0])))
+			ret = -EFAULT;
+	}
+
+	if (ret) {
+		for (i = 0; i < num_mems; i++) {
+			if (mems[i].fd)
+				put_unused_fd(mems[i].fd);
+		}
+	}
+
+	kfree(mems);
+	return ret;
+}
+
+/**
+ * aie_part_has_mem_mmapped() - check if memories in the partition are mapped
+ * @apart: AI engine partition
+ * @return: return true if there are memories mmaped, false otherwise.
+ *
+ * This function checks if there are memories in the partition mmapped in the
+ * partition.
+ */
+bool aie_part_has_mem_mmapped(struct aie_partition *apart)
+{
+	unsigned int num_mems, i;
+
+	num_mems = apart->adev->ops->get_mem_info(apart->adev, &apart->range,
+			NULL);
+	if (!num_mems)
+		return false;
+
+	for (i = 0; i < num_mems; i++) {
+		if (apart->pmems[i].dbuf)
+			return true;
+	}
+	return false;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-overlay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-overlay.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/xlnx-ai-engine.h>
+#include <uapi/linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+/**
+ * of_aie_notify_pre_remove() - pre-remove overlay notification
+ *
+ * @adev: AI engine device
+ * @nd: overlay notification data
+ * @return: returns 0 for success, and error code for failure.
+ *
+ * Called when an overlay targeted to an AI engine device is about to be
+ * removed. Remove AI engine apertures specified in the device tree overlay to
+ * the target AI engine device.
+ */
+static int of_aie_notify_pre_remove(struct aie_device *adev,
+				    struct of_overlay_notify_data *nd)
+{
+	struct device_node *nc;
+
+	for_each_available_child_of_node(nd->overlay, nc) {
+		struct list_head *node, *pos;
+		int ret;
+
+		if (!of_node_test_and_set_flag(nc, OF_POPULATED))
+			continue;
+
+		ret = mutex_lock_interruptible(&adev->mlock);
+		if (ret)
+			return ret;
+
+		list_for_each_safe(pos, node, &adev->apertures) {
+			struct aie_aperture *aperture;
+
+			aperture = list_entry(pos, struct aie_aperture, node);
+			ret = aie_aperture_remove(aperture);
+			if (ret) {
+				mutex_unlock(&adev->mlock);
+				return ret;
+			}
+		}
+
+		mutex_unlock(&adev->mlock);
+	}
+
+	return 0;
+}
+
+/**
+ * of_aie_notify() - AI engine notifier for dynamic DT changes
+ * @nb: notifier block
+ * @action: notifier action
+ * @arg: reconfig data
+ * @return: NOTIFY_OK for success, error code for failure
+ *
+ * This notifier handles AI engine device node overlay.
+ */
+static int of_aie_notify(struct notifier_block *nb, unsigned long action,
+			 void *arg)
+{
+	struct of_overlay_notify_data *nd = arg;
+	struct aie_device *adev;
+	int ret = 0;
+
+	switch (action) {
+	case OF_OVERLAY_POST_APPLY:
+		adev = of_ai_engine_class_find(nd->target);
+		if (!adev) {
+			pr_debug("%s OF_OVERLAY_POST_APPLY\n", __func__);
+			return NOTIFY_OK;
+		}
+
+		of_xilinx_ai_engine_aperture_probe(adev);
+		break;
+	case OF_OVERLAY_PRE_REMOVE:
+		adev = of_ai_engine_class_find(nd->target);
+		if (!adev) {
+			pr_debug("%s OF_OVERLAY_POST_APPLY\n", __func__);
+			return NOTIFY_OK;
+		}
+
+		ret = of_aie_notify_pre_remove(adev, nd);
+		break;
+	default:
+		return NOTIFY_OK;
+	}
+
+	if (ret)
+		return notifier_from_errno(ret);
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block aie_of_nb = {
+	.notifier_call = of_aie_notify,
+};
+
+/**
+ * aie_overlay_register_notifier() - register AI engine device tree overlay
+ *				     notifier
+ * @return: 0 for success, error code for failure
+ */
+int aie_overlay_register_notifier(void)
+{
+	return of_overlay_notifier_register(&aie_of_nb);
+}
+
+/**
+ * aie_overlay_unregister_notifier() - unregister AI engine device tree overlay
+ *				       notifier
+ */
+void aie_overlay_unregister_notifier(void)
+{
+	of_overlay_notifier_unregister(&aie_of_nb);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-part.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-part.c
@@ -0,0 +1,1079 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine partition driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/cdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/dma-map-ops.h>
+#include <linux/fs.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mman.h>
+#include <linux/mmu_context.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/uio.h>
+#include <uapi/linux/xlnx-ai-engine.h>
+
+#include "ai-engine-internal.h"
+
+/**
+ * aie_cal_loc() - calculate tile location from register offset to the AI
+ *		   engine device
+ * @adev: AI engine device
+ * @loc: memory pointer to restore returning location information
+ * @regoff: tile internal register offset
+ *
+ * This function returns the tile location.
+ */
+static void aie_cal_loc(struct aie_device *adev,
+			struct aie_location *loc, u64 regoff)
+{
+	loc->col = (u32)aie_tile_reg_field_get(aie_col_mask(adev),
+					       adev->col_shift, regoff);
+	loc->row = (u32)aie_tile_reg_field_get(aie_row_mask(adev),
+					       adev->row_shift, regoff);
+}
+
+/**
+ * aie_part_reg_validation() - validate AI engine partition register access
+ * @apart: AI engine partition
+ * @offset: AI engine register offset relative in partition.
+ * @len: len of data to write/read
+ * @is_write: is the access to write to register
+ * @return: 0 for success, or negative value for failure.
+ *
+ * This function validate if the register to access is within the AI engine
+ * partition. If it is write access, if the register is writable by user.
+ */
+static int aie_part_reg_validation(struct aie_partition *apart, size_t offset,
+				   size_t len, u8 is_write)
+{
+	struct aie_device *adev;
+	u32 regend32, ttype;
+	u64 regoff, regend64;
+	struct aie_location loc, aloc;
+	unsigned int i;
+
+	adev = apart->adev;
+	if (offset % sizeof(u32)) {
+		dev_err(&apart->dev,
+			"Invalid reg off(0x%zx), not 32bit aligned.\n",
+			offset);
+		return -EINVAL;
+	}
+
+	if (len % sizeof(u32)) {
+		dev_err(&apart->dev, "Invalid reg operation len %zu.\n", len);
+		return -EINVAL;
+	}
+
+	regoff = aie_cal_tile_reg(adev, offset);
+	regend64 = regoff + len - 1;
+	if (regend64 >= BIT_ULL(adev->row_shift)) {
+		dev_err(&apart->dev,
+			"Invalid reg operation len %zu.\n", len);
+		return -EINVAL;
+	}
+
+	aie_cal_loc(adev, &loc, offset);
+	if (aie_validate_location(apart, loc)) {
+		dev_err(&apart->dev,
+			"Invalid (%d,%d) out of part(%d,%d)\n",
+			loc.col, loc.row,
+			apart->range.size.col, apart->range.size.row);
+		return -EINVAL;
+	}
+
+	/*
+	 * We check if a tile is gated before trying to access the tile.
+	 * As we mmap() the registers as read only to enable faster status
+	 * enquiry, and mmap() memories as write/read to faster memory access,
+	 * user can still access the clock gated tiles from userspace by
+	 * accessing the mmapped space.
+	 * Accessing the gated tiles can cause decode error. With PDI flow,
+	 * the PDI sets up the SHIM NOC AXI MM to only generate AI engine error
+	 * even instead of generating the NSU error. but for non PDI flow, as
+	 * the AXI MM register are protected register, until we have EEMI API
+	 * to update the AXI MM register, access the gated tiles can cause NSU
+	 * errors.
+	 * TODO: To solve this, we need to either request EEMI to configure
+	 * AXI MM or split the mmapped space into tiles based lists.
+	 */
+	aloc.col = loc.col + apart->range.start.col;
+	aloc.row = loc.row;
+	if (!aie_part_check_clk_enable_loc(apart, &aloc)) {
+		dev_err(&apart->dev,
+			"Tile(%u,%d) is gated.\n", loc.col, loc.row);
+		return -EINVAL;
+	}
+
+	if (!is_write)
+		return 0;
+
+	regend32 = lower_32_bits(regend64);
+	ttype = adev->ops->get_tile_type(adev, &loc);
+	for (i = 0; i < adev->num_kernel_regs; i++) {
+		const struct aie_tile_regs *regs;
+		u32 rttype, writable;
+
+		regs = &adev->kernel_regs[i];
+		rttype = (regs->attribute & AIE_REGS_ATTR_TILE_TYPE_MASK) >>
+			 AIE_REGS_ATTR_TILE_TYPE_SHIFT;
+		writable = (regs->attribute & AIE_REGS_ATTR_PERM_MASK) >>
+			   AIE_REGS_ATTR_PERM_SHIFT;
+		if (!(BIT(ttype) & rttype))
+			continue;
+		if ((regoff >= regs->soff && regoff <= regs->eoff) ||
+		    (regend32 >= regs->soff && regend32 <= regs->eoff)) {
+			if (!writable) {
+				dev_err(&apart->dev,
+					"reg 0x%zx,0x%zx not writable.\n",
+					offset, len);
+				return -EINVAL;
+			}
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_write_register() - AI engine partition write register
+ * @apart: AI engine partition
+ * @offset: AI engine register offset
+ * @len: len of data to write
+ * @data: data to write
+ * @mask: mask, if it is non 0, it is mask write.
+ * @return: number of bytes write for success, or negative value for failure.
+ *
+ * This function writes data to the specified registers.
+ * If the mask is non 0, it is mask write.
+ */
+static int aie_part_write_register(struct aie_partition *apart, size_t offset,
+				   size_t len, void *data, u32 mask)
+{
+	struct aie_aperture *aperture = apart->aperture;
+	u32 i;
+	int ret;
+	void __iomem *va;
+
+	if (mask && len > sizeof(u32)) {
+		/* For mask write, only allow 32bit. */
+		dev_err(&apart->dev,
+			"failed mask write, len is more that 32bit.\n");
+		return -EINVAL;
+	}
+
+	/* offset is expected to be relative to the start of the partition */
+	ret = aie_part_reg_validation(apart, offset, len, 1);
+	if (ret < 0) {
+		dev_err(&apart->dev, "failed to write to 0x%zx,0x%zx.\n",
+			offset, len);
+		return ret;
+	}
+
+	offset += aie_aperture_cal_regoff(aperture, apart->range.start, 0);
+	va = aperture->base + offset;
+	if (!mask) {
+		/*
+		 * TODO: use the burst mode to improve performance when len
+		 * is more than 4. Additional checks have to be made to ensure
+		 * the destination address is 128 bit aligned when burst mode
+		 * is used.
+		 */
+		for (i = 0; i < len; i = i + 4)
+			iowrite32(*((u32 *)(data + i)), va + i);
+	} else {
+		u32 val = ioread32(va);
+
+		val &= ~mask;
+		val |= *((u32 *)data) & mask;
+		iowrite32(val, va);
+	}
+
+	return (int)len;
+}
+
+/**
+ * aie_part_read_register() - AI engine partition read register
+ * @apart: AI engine partition
+ * @offset: AI engine register offset
+ * @len: len of data to read
+ * @data: pointer to the memory to store the read data
+ * @return: number of bytes read for success, or negative value for failure.
+ *
+ * This function reads data from the specified registers.
+ */
+static int aie_part_read_register(struct aie_partition *apart, size_t offset,
+				  size_t len, void *data)
+{
+	struct aie_aperture *aperture = apart->aperture;
+	void __iomem *va;
+	int ret;
+
+	/* offset is expected to be relative to the start of the partition */
+	ret = aie_part_reg_validation(apart, offset, len, 0);
+	if (ret) {
+		dev_err(&apart->dev, "Invalid read request 0x%zx,0x%zx.\n",
+			offset, len);
+		return -EINVAL;
+	}
+
+	offset += aie_aperture_cal_regoff(aperture, apart->range.start, 0);
+	va = aperture->base + offset;
+	if (len == 4)
+		*((u32 *)data) = ioread32(va);
+	else
+		memcpy_fromio(data, va, len);
+
+	return (int)len;
+}
+
+/**
+ * aie_part_block_set() - AI Engine partition block set registers
+ * @apart: AI engine partition
+ * @args: regestier access arguments
+ * @return: 0 for success, and negative value for failure
+ */
+static int aie_part_block_set(struct aie_partition *apart,
+			      struct aie_reg_args *args)
+{
+	u32 i;
+	int ret;
+
+	for (i = 0; i < args->len; i++) {
+		size_t offset = (size_t)args->offset;
+
+		ret = aie_part_write_register(apart, offset + i * 4,
+					      sizeof(args->val), &args->val,
+					      args->mask);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_pin_user_region() - pin user pages for access
+ * @apart: AI engine partition
+ * @region: user space region to pin. Includes virtual address and size of the
+ *	    user space buffer.
+ * @return: 0 for success, and negative value for failure.
+ *
+ * This function pins all the pages of a user space buffer.
+ */
+static int aie_part_pin_user_region(struct aie_partition *apart,
+				    struct aie_part_pinned_region *region)
+{
+	int ret, npages;
+	unsigned long first, last;
+	struct page **pages;
+
+	first = (region->user_addr & PAGE_MASK) >> PAGE_SHIFT;
+	last = ((region->user_addr + region->len - 1) & PAGE_MASK) >>
+		PAGE_SHIFT;
+	npages = last - first + 1;
+
+	pages = kcalloc(npages, sizeof(struct page *), GFP_KERNEL);
+	if (!pages)
+		return -ENOMEM;
+
+	ret = pin_user_pages_fast(region->user_addr, npages, 0, pages);
+	if (ret < 0) {
+		kfree(pages);
+		dev_err(&apart->dev, "Unable to pin user pages\n");
+		return ret;
+	} else if (ret != npages) {
+		unpin_user_pages(pages, ret);
+		kfree(pages);
+		dev_err(&apart->dev, "Unable to pin all user pages\n");
+		return -EFAULT;
+	}
+
+	region->pages = pages;
+	region->npages = npages;
+
+	return 0;
+}
+
+/**
+ * aie_part_unpin_user_region() - unpin user pages
+ * @region: user space region to unpin.
+ *
+ * This function unpins all the pages of a user space buffer. User region passed
+ * to this api must be pinned using aie_part_pin_user_region()
+ */
+static void aie_part_unpin_user_region(struct aie_part_pinned_region *region)
+{
+	unpin_user_pages(region->pages, region->npages);
+	kfree(region->pages);
+}
+
+/**
+ * aie_part_access_regs() - AI engine partition registers access
+ * @apart: AI engine partition
+ * @num_reqs: number of access requests
+ * @reqs: array of registers access
+ * @return: 0 for success, and negative value for failure.
+ *
+ * This function executes AI engine partition register access requests.
+ */
+static int aie_part_access_regs(struct aie_partition *apart, u32 num_reqs,
+				struct aie_reg_args *reqs)
+{
+	u32 i;
+
+	for (i = 0; i < num_reqs; i++) {
+		struct aie_reg_args *args = &reqs[i];
+		int ret;
+
+		switch (args->op) {
+		case AIE_REG_WRITE:
+		{
+			ret = aie_part_write_register(apart,
+						      (size_t)args->offset,
+						      sizeof(args->val),
+						      &args->val, args->mask);
+			break;
+		}
+		case AIE_REG_BLOCKWRITE:
+		{
+			struct aie_part_pinned_region region;
+
+			region.user_addr = args->dataptr;
+			region.len = args->len * sizeof(u32);
+			ret = aie_part_pin_user_region(apart, &region);
+			if (ret)
+				break;
+
+			ret = aie_part_write_register(apart,
+						      (size_t)args->offset,
+						      sizeof(u32) * args->len,
+						      (void *)args->dataptr,
+						      args->mask);
+			aie_part_unpin_user_region(&region);
+			break;
+		}
+		case AIE_REG_BLOCKSET:
+		{
+			ret = aie_part_block_set(apart, args);
+			break;
+		}
+		default:
+			dev_err(&apart->dev,
+				"Invalid register command type: %u.\n",
+				args->op);
+			return -EINVAL;
+		}
+
+		if (ret < 0) {
+			dev_err(&apart->dev, "reg op %u failed: 0x%llx.\n",
+				args->op, args->offset);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_execute_transaction_from_user() - AI engine configure registers
+ * @apart: AI engine partition
+ * @user_args: arguments passed by user.
+ * @return: 0 for success, and negative value for failure.
+ *
+ * This function executes AI engine register access requests that are part of a
+ * buffer that is populated and passed by user.
+ */
+static int aie_part_execute_transaction_from_user(struct aie_partition *apart,
+						  void __user *user_args)
+{
+	long ret;
+	struct aie_txn_inst txn_inst;
+	struct aie_part_pinned_region region;
+
+	if (copy_from_user(&txn_inst, user_args, sizeof(txn_inst)))
+		return -EFAULT;
+
+	region.user_addr = txn_inst.cmdsptr;
+	region.len = txn_inst.num_cmds * sizeof(struct aie_reg_args);
+	ret = aie_part_pin_user_region(apart, &region);
+	if (ret)
+		return ret;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		aie_part_unpin_user_region(&region);
+		return ret;
+	}
+
+	ret = aie_part_access_regs(apart, txn_inst.num_cmds,
+				   (struct aie_reg_args *)region.user_addr);
+
+	mutex_unlock(&apart->mlock);
+
+	aie_part_unpin_user_region(&region);
+	return ret;
+}
+
+/**
+ * aie_part_create_event_bitmap() - create event bitmap for all modules in a
+ *				    given partition.
+ * @apart: AI engine partition
+ * @return: 0 for success, and negative value for failure.
+ */
+static int aie_part_create_event_bitmap(struct aie_partition *apart)
+{
+	struct aie_range range = apart->range;
+	u32 bitmap_sz;
+	u32 num_aie_module = range.size.col * (range.size.row - 1);
+	int ret;
+
+	/*
+	 * TODO: resource manager, events is not supported for AIEML device and
+	 * the users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_dbg(&apart->dev, "Skipping event bitmap allocation.\n");
+		return 0;
+	}
+	bitmap_sz = num_aie_module * apart->adev->core_events->num_events;
+	ret = aie_resource_initialize(&apart->core_event_status, bitmap_sz);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to initialize event status resource.\n");
+		return -ENOMEM;
+	}
+
+	bitmap_sz = num_aie_module * apart->adev->mem_events->num_events;
+	ret = aie_resource_initialize(&apart->mem_event_status, bitmap_sz);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to initialize event status resource.\n");
+		return -ENOMEM;
+	}
+
+	bitmap_sz = range.size.col * apart->adev->pl_events->num_events;
+	ret = aie_resource_initialize(&apart->pl_event_status, bitmap_sz);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to initialize event status resource.\n");
+		return -ENOMEM;
+	}
+	return 0;
+}
+
+/**
+ * aie_part_release_event_bitmap() - Deallocates event bitmap for all modules
+ *				     in a given partition.
+ * @apart: AI engine partition
+ * @return: 0 for success, and negative value for failure.
+ */
+static void aie_part_release_event_bitmap(struct aie_partition *apart)
+{
+	/* TODO: remove check once resource manager is enabled for AIEML. */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML)
+		return;
+
+	aie_resource_uninitialize(&apart->core_event_status);
+	aie_resource_uninitialize(&apart->mem_event_status);
+	aie_resource_uninitialize(&apart->pl_event_status);
+}
+
+static int aie_part_release(struct inode *inode, struct file *filp)
+{
+	struct aie_partition *apart = filp->private_data;
+	int ret;
+
+	/* some reset bits in NPI are global, we need to lock adev */
+	ret = mutex_lock_interruptible(&apart->adev->mlock);
+	if (ret)
+		return ret;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret)
+		return ret;
+
+	aie_part_release_dmabufs(apart);
+	/* aie_part_clean() will do hardware reset */
+	aie_part_clean(apart);
+	mutex_unlock(&apart->adev->mlock);
+
+	apart->error_cb.cb = NULL;
+	apart->error_cb.priv = NULL;
+	apart->status = 0;
+	apart->error_to_report = 0;
+
+	aie_part_clear_cached_events(apart);
+
+	aie_part_rscmgr_reset(apart);
+
+	mutex_unlock(&apart->mlock);
+	aie_part_remove(apart);
+
+	return 0;
+}
+
+static ssize_t aie_part_write_iter(struct kiocb *iocb, struct iov_iter *from)
+{
+	struct file *filp = iocb->ki_filp;
+	struct aie_partition *apart = filp->private_data;
+	size_t len = iov_iter_count(from);
+	loff_t offset = iocb->ki_pos;
+	void *buf;
+	int ret;
+
+	buf = kzalloc(len, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+	if (!copy_from_iter_full(buf, len, from)) {
+		kfree(buf);
+		return -EFAULT;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(buf);
+		return ret;
+	}
+
+	ret = aie_part_write_register(apart, (size_t)offset, len, buf, 0);
+	mutex_unlock(&apart->mlock);
+	kfree(buf);
+
+	return ret;
+}
+
+static ssize_t aie_part_read_iter(struct kiocb *iocb, struct iov_iter *to)
+{
+	struct file *filp = iocb->ki_filp;
+	struct aie_partition *apart = filp->private_data;
+	size_t len = iov_iter_count(to);
+	loff_t offset = iocb->ki_pos;
+	void *buf;
+	int ret;
+
+	buf = kzalloc(len, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(buf);
+		return ret;
+	}
+
+	ret = aie_part_read_register(apart, (size_t)offset, len, buf);
+	mutex_unlock(&apart->mlock);
+	if (ret > 0) {
+		if (copy_to_iter(buf, ret, to) != len) {
+			dev_err(&apart->dev, "Failed to copy to read iter.\n");
+			ret = -EFAULT;
+		}
+	}
+	kfree(buf);
+
+	return ret;
+}
+
+static const struct vm_operations_struct aie_part_physical_vm_ops = {
+#ifdef CONFIG_HAVE_IOREMAP_PROT
+	.access = generic_access_phys,
+#endif
+};
+
+static int aie_part_mmap(struct file *fp, struct vm_area_struct *vma)
+{
+	struct aie_partition *apart = fp->private_data;
+	struct aie_device *adev = apart->adev;
+	unsigned long offset = vma->vm_pgoff * PAGE_SIZE;
+	phys_addr_t addr;
+	size_t size;
+
+	if (vma->vm_end < vma->vm_start)
+		return -EINVAL;
+	/* Only allow userspace directly read registers */
+	if (vma->vm_flags & VM_WRITE) {
+		dev_err(&apart->dev, "%s: do not support writable mmap.\n",
+			__func__);
+		return -EINVAL;
+	}
+	vma->vm_private_data = apart;
+	vma->vm_ops = &aie_part_physical_vm_ops;
+	size = apart->range.size.col << adev->col_shift;
+	if ((vma->vm_end - vma->vm_start) > (size - offset)) {
+		dev_err(&apart->dev,
+			"%s: size exceed.\n", __func__);
+		return -EINVAL;
+	}
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	/* Calculate the partition address */
+	addr = apart->aperture->res.start;
+	addr += (phys_addr_t)apart->range.start.col << adev->col_shift;
+	addr += (phys_addr_t)apart->range.start.row << adev->row_shift;
+	addr += offset;
+	return remap_pfn_range(vma,
+			       vma->vm_start,
+			       addr >> PAGE_SHIFT,
+			       vma->vm_end - vma->vm_start,
+			       vma->vm_page_prot);
+}
+
+static long aie_part_ioctl(struct file *fp, unsigned int cmd, unsigned long arg)
+{
+	struct aie_partition *apart = fp->private_data;
+	void __user *argp = (void __user *)arg;
+	long ret;
+
+	switch (cmd) {
+	case AIE_REG_IOCTL:
+	{
+		struct aie_reg_args raccess;
+
+		if (copy_from_user(&raccess, argp, sizeof(raccess)))
+			return -EFAULT;
+
+		ret = mutex_lock_interruptible(&apart->mlock);
+		if (ret)
+			return ret;
+
+		ret = aie_part_access_regs(apart, 1, &raccess);
+		mutex_unlock(&apart->mlock);
+		break;
+	}
+	case AIE_GET_MEM_IOCTL:
+		return aie_mem_get_info(apart, arg);
+	case AIE_ATTACH_DMABUF_IOCTL:
+		return aie_part_attach_dmabuf_req(apart, argp);
+	case AIE_DETACH_DMABUF_IOCTL:
+		return aie_part_detach_dmabuf_req(apart, argp);
+	case AIE_SET_SHIMDMA_BD_IOCTL:
+		return aie_part_set_bd(apart, argp);
+	case AIE_SET_SHIMDMA_DMABUF_BD_IOCTL:
+		return aie_part_set_dmabuf_bd(apart, argp);
+	case AIE_REQUEST_TILES_IOCTL:
+		return aie_part_request_tiles_from_user(apart, argp);
+	case AIE_RELEASE_TILES_IOCTL:
+		return aie_part_release_tiles_from_user(apart, argp);
+	case AIE_TRANSACTION_IOCTL:
+		return aie_part_execute_transaction_from_user(apart, argp);
+	case AIE_RSC_REQ_IOCTL:
+		return aie_part_rscmgr_rsc_req(apart, argp);
+	case AIE_RSC_REQ_SPECIFIC_IOCTL:
+		return aie_part_rscmgr_rsc_req_specific(apart, argp);
+	case AIE_RSC_RELEASE_IOCTL:
+		return aie_part_rscmgr_rsc_release(apart, argp);
+	case AIE_RSC_FREE_IOCTL:
+		return aie_part_rscmgr_rsc_free(apart, argp);
+	case AIE_RSC_CHECK_AVAIL_IOCTL:
+		return aie_part_rscmgr_rsc_check_avail(apart, argp);
+	case AIE_RSC_GET_COMMON_BROADCAST_IOCTL:
+		return aie_part_rscmgr_get_broadcast(apart, argp);
+	case AIE_RSC_GET_STAT_IOCTL:
+		return aie_part_rscmgr_get_statistics(apart, argp);
+	default:
+		dev_err(&apart->dev, "Invalid/Unsupported ioctl command %u.\n",
+			cmd);
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+const struct file_operations aie_part_fops = {
+	.owner		= THIS_MODULE,
+	.release	= aie_part_release,
+	.read_iter	= aie_part_read_iter,
+	.write_iter	= aie_part_write_iter,
+	.mmap		= aie_part_mmap,
+	.unlocked_ioctl	= aie_part_ioctl,
+};
+
+/**
+ * aie_part_open() - open the AI engine partition instance to get it ready to
+ *		     be used.
+ * @apart: AI engine partition instance pointer
+ * @rsc_metadata: pointer to static resource metadata
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will make the AI engine partition instance ready to use. It
+ * should be called when the partition is requested.
+ */
+int aie_part_open(struct aie_partition *apart, void *rsc_metadata)
+{
+	int ret;
+
+	/* scan to setup the initial clock state for tiles */
+	ret = aie_part_scan_clk_state(apart);
+	if (ret)
+		return ret;
+
+	/* Sets bitmaps of statically allocated resources */
+	if (rsc_metadata) {
+		ret = aie_part_rscmgr_set_static(apart,
+						 rsc_metadata);
+		if (ret)
+			return ret;
+	}
+
+	/* preallocate memory pool for storing dmabuf descriptors */
+	ret =  aie_part_prealloc_dbufs_cache(apart);
+	if (ret)
+		return ret;
+
+	/* check if there is any errors reported for the partition */
+	if (aie_part_has_error(apart))
+		schedule_work(&apart->aperture->backtrack);
+
+	apart->status = XAIE_PART_STATUS_INUSE;
+
+	return 0;
+}
+
+/**
+ * aie_tile_release_device() - release an AI engine tile instance
+ * @dev: AI engine tile device
+ *
+ * It will be called by device driver core when no one holds a valid
+ * pointer to @dev anymore.
+ */
+static void aie_tile_release_device(struct device *dev)
+{
+	(void)dev;
+}
+
+/**
+ * aie_part_release_device() - release an AI engine partition instance
+ * @dev: AI engine partition device
+ *
+ * It will be called by device driver core when no one holds a valid
+ * pointer to @dev anymore.
+ */
+static void aie_part_release_device(struct device *dev)
+{
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_aperture *aperture = apart->aperture;
+	int ret;
+
+	ret = mutex_lock_interruptible(&aperture->mlock);
+	if (ret) {
+		dev_warn(&apart->dev,
+			 "getting adev->mlock is interrupted by signal\n");
+	}
+
+	aie_resource_put_region(&aperture->cols_res, apart->range.start.col,
+				apart->range.size.col);
+	aie_part_release_event_bitmap(apart);
+	list_del(&apart->node);
+	mutex_unlock(&aperture->mlock);
+	aie_resource_uninitialize(&apart->cores_clk_state);
+	aie_resource_uninitialize(&apart->tiles_inuse);
+	aie_part_rscmgr_finish(apart);
+	/* Check and set frequency requirement for aperture */
+	aie_part_set_freq(apart, 0);
+}
+
+/**
+ * aie_part_create_mems_info() - creates array to store the AI engine partition
+ *				 different memories types information
+ * @apart: AI engine partition
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will create array to store the information of different
+ * memories types in the partition. This array is stored in @apart->pmems.
+ */
+static int aie_part_create_mems_info(struct aie_partition *apart)
+{
+	unsigned int i, num_mems;
+
+	num_mems = apart->adev->ops->get_mem_info(apart->adev, &apart->range,
+						  NULL);
+	if (!num_mems)
+		return 0;
+
+	apart->pmems = devm_kcalloc(&apart->dev, num_mems,
+				    sizeof(struct aie_part_mem),
+				    GFP_KERNEL);
+	if (!apart->pmems)
+		return -ENOMEM;
+
+	apart->adev->ops->get_mem_info(apart->adev, &apart->range,
+				       apart->pmems);
+	for (i = 0; i < num_mems; i++) {
+		struct aie_mem *mem = &apart->pmems[i].mem;
+
+		apart->pmems[i].apart = apart;
+		apart->pmems[i].size = mem->size *
+				       mem->range.size.col *
+				       mem->range.size.row;
+	}
+	return 0;
+}
+
+/**
+ * aie_create_tiles() - create AI engine tile devices
+ * @apart: AI engine partition
+ * @return: 0 for success, error code on failure
+ *
+ * This function creates AI engine child tile devices for a given partition.
+ */
+static int aie_create_tiles(struct aie_partition *apart)
+{
+	struct aie_tile *atile;
+	u32 row, col, numtiles;
+	int ret = 0;
+
+	/*
+	 * NOTE: sysfs is supported for AIE only. Remove the below check once
+	 * it is supported.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_dbg(&apart->dev, "Skipping sysfs partition\n");
+		return 0;
+	}
+
+	numtiles = apart->range.size.col * apart->range.size.row;
+	atile = devm_kzalloc(&apart->dev, numtiles * sizeof(struct aie_tile),
+			     GFP_KERNEL);
+	if (!atile)
+		return -ENOMEM;
+
+	apart->atiles = atile;
+	for (col = 0; col < apart->range.size.col; col++) {
+		for (row = 0; row < apart->range.size.row; row++) {
+			struct device *tdev = &atile->dev;
+			char tdevname[10];
+
+			atile->apart = apart;
+			atile->loc.col = apart->range.start.col + col;
+			atile->loc.row = apart->range.start.row + row;
+			device_initialize(tdev);
+			tdev->parent = &apart->dev;
+			dev_set_drvdata(tdev, atile);
+			snprintf(tdevname, sizeof(tdevname) - 1, "%d_%d",
+				 apart->range.start.col + col,
+				 apart->range.start.row + row);
+			dev_set_name(tdev, tdevname);
+			tdev->release = aie_tile_release_device;
+			ret = device_add(tdev);
+			if (ret) {
+				dev_err(tdev, "tile device_add failed: %d\n",
+					ret);
+				put_device(tdev);
+				return ret;
+			}
+			ret = aie_tile_sysfs_create_entries(atile);
+			if (ret) {
+				dev_err(tdev, "failed to create tile sysfs: %d\n",
+					ret);
+				device_del(tdev);
+				put_device(tdev);
+				return ret;
+			}
+			atile++;
+		}
+	}
+	return ret;
+}
+
+/**
+ * aie_create_partition() - create AI engine partition instance
+ * @aperture: AI engine aperture
+ * @partition_id: AI engine partition ID which contains partition range
+ *		  information such as start column and number of columns
+ * @return: created AI engine partition pointer for success, and PTR_ERR
+ *	    for failure.
+ *
+ * This function creates an AI engine partition instance.
+ * It creates AI engine partition, the AI engine partition device and
+ * the AI engine partition character device.
+ */
+struct aie_partition *aie_create_partition(struct aie_aperture *aperture,
+					   u32 partition_id)
+{
+	struct aie_partition *apart;
+	struct device *dev;
+	int ret;
+
+	apart = devm_kzalloc(&aperture->dev, sizeof(*apart), GFP_KERNEL);
+	if (!apart)
+		return ERR_PTR(-ENOMEM);
+
+	apart->aperture = aperture;
+	apart->adev = aperture->adev;
+	apart->partition_id = partition_id;
+	INIT_LIST_HEAD(&apart->dbufs);
+	mutex_init(&apart->mlock);
+	apart->range.start.col = aie_part_id_get_start_col(partition_id);
+	apart->range.size.col = aie_part_id_get_num_cols(partition_id);
+	apart->range.start.row = aperture->range.start.row;
+	apart->range.size.row = aperture->range.size.row;
+
+	/* Create AI engine partition device */
+	dev = &apart->dev;
+	dev->parent = &aperture->dev;
+	dev->class = aie_class;
+	dev_set_drvdata(dev, apart);
+	dev_set_name(dev, "aiepart_%d_%d", apart->range.start.col,
+		     apart->range.size.col);
+	/* We can now rely on the release function for cleanup */
+	dev->release = aie_part_release_device;
+	ret = device_register(dev);
+	if (ret) {
+		dev_err(dev, "device_add failed: %d\n", ret);
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	/* Set up the DMA mask */
+	set_dma_ops(dev, get_dma_ops(&aperture->dev));
+	ret = dma_coerce_mask_and_coherent(dev, dma_get_mask(&aperture->dev));
+	if (ret) {
+		dev_warn(dev,
+			 "Failed to set DMA mask %llx. Trying to continue... %x\n",
+			 dma_get_mask(&aperture->dev), ret);
+	}
+
+	/* Create AI Engine tile devices */
+	ret = aie_create_tiles(apart);
+	if (ret) {
+		dev_err(dev, "Failed to create tile devices.\n");
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	/*
+	 * Create array to keep the information of the different types of tile
+	 * memories information of the AI engine partition.
+	 */
+	ret = aie_part_create_mems_info(apart);
+	if (ret) {
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	ret = apart->adev->ops->init_part_clk_state(apart);
+	if (ret) {
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	/*
+	 * Create bitmap to record event status for each module in a
+	 * partition
+	 */
+	ret = aie_part_create_event_bitmap(apart);
+	if (ret < 0) {
+		dev_err(&apart->dev, "Failed to allocate event bitmap.\n");
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	ret = aie_part_rscmgr_init(apart);
+	if (ret < 0) {
+		dev_err(&apart->dev,
+			"Failed to initialize resources bitmaps.\n");
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	ret = aie_part_sysfs_create_entries(apart);
+	if (ret) {
+		dev_err(&apart->dev, "Failed to create partition sysfs.\n");
+		put_device(dev);
+		return ERR_PTR(ret);
+	}
+
+	dev_dbg(dev, "created AIE partition device.\n");
+
+	return apart;
+}
+
+/**
+ * aie_tile_remove() - remove AI engine tile device.
+ * @atile: AI engine tile.
+ *
+ * This function will remove AI engine tile device.
+ */
+static void aie_tile_remove(struct aie_tile *atile)
+{
+	aie_tile_sysfs_remove_entries(atile);
+	device_del(&atile->dev);
+	put_device(&atile->dev);
+}
+
+/**
+ * aie_part_remove() - destroy AI engine partition
+ * @apart: AI engine partition
+ *
+ * This function will remove AI engine partition.
+ */
+void aie_part_remove(struct aie_partition *apart)
+{
+	struct aie_tile *atile = apart->atiles;
+	u32 index;
+
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_dbg(&apart->dev, "Skipping sysfs pattition\n");
+		goto delete;
+	}
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++)
+		aie_tile_remove(atile);
+
+	aie_part_sysfs_remove_entries(apart);
+delete:
+	device_del(&apart->dev);
+	put_device(&apart->dev);
+}
+
+/**
+ * aie_part_has_regs_mmapped() - check if registers in the partition are mapped.
+ * @apart: AI engine partition
+ * @return: return true if there are registers mmaped, false otherwise.
+ *
+ * This function checks if there are registerss in the partition mmapped in the
+ * partition.
+ */
+bool aie_part_has_regs_mmapped(struct aie_partition *apart)
+{
+	struct address_space *mapping;
+
+	mapping = apart->filep->f_inode->i_mapping;
+	return mapping_mapped(mapping);
+}
+
+/**
+ * aie_part_get_tile_rows - helper function to get the number of rows of a
+ *			    tile type.
+ *
+ * @apart: AI engine partition
+ * @ttype: tile type
+ * @return: number of rows of a tile type
+ */
+int aie_part_get_tile_rows(struct aie_partition *apart,
+			   enum aie_tile_type ttype)
+{
+	struct aie_tile_attr *tattr = &apart->adev->ttype_attr[ttype];
+
+	/*
+	 * TODO: number of rows information of the AI engine device
+	 * should get from device tree.
+	 */
+	if (tattr->num_rows != 0xFF)
+		return tattr->num_rows;
+	else
+		return (apart->range.size.row - tattr->start_row);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-res.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-res.c
@@ -0,0 +1,466 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/bitmap.h>
+
+#include "ai-engine-internal.h"
+
+/**
+ * aie_resource_initialize() - initialize AI engine resource
+ * @res: pointer to AI engine resource
+ * @count: total number of element of this resource
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will initialize the data structure for the
+ * resource.
+ */
+int aie_resource_initialize(struct aie_resource *res, int count)
+{
+	if (!res || !count)
+		return -EINVAL;
+	res->bitmap = bitmap_zalloc(count, GFP_KERNEL);
+	if (!res->bitmap)
+		return -ENOMEM;
+	res->total = count;
+
+	return 0;
+}
+
+/**
+ * aie_resource_uninitialize() - uninitialize AI engine resource
+ * @res: pointer to AI engine resource
+ *
+ * This function will release the AI engine resource data members.
+ */
+void aie_resource_uninitialize(struct aie_resource *res)
+{
+	res->total = 0;
+	if (res->bitmap)
+		bitmap_free(res->bitmap);
+}
+
+/**
+ * aie_resource_check_region() - check availability of requested resource
+ * @res: pointer to AI engine resource to check
+ * @start: start index of the required resource, it will only be used if
+ *	   @continuous is 1. It will check the available resource starting from
+ *	   @start
+ * @count: number of requested element
+ * @return: start resource id if the requested number of resources are available
+ *	    It will return negative value of errors.
+ *
+ * This function will check the availability. It will return start resource id
+ * if the requested number of resources are available.
+ */
+int aie_resource_check_region(struct aie_resource *res,
+			      u32 start, u32 count)
+{
+	unsigned long id;
+
+	if (!res || !res->bitmap || !count)
+		return -EINVAL;
+	id = bitmap_find_next_zero_area(res->bitmap, res->total, start,
+					count, 0);
+	if (id >= res->total)
+		return -ERANGE;
+
+	return (int)id;
+}
+
+/**
+ * aie_resource_get_region() - get requested AI engine resource
+ * @res: pointer to AI engine resource to check
+ * @count: number of requested element
+ * @start: start index of the required resource
+ * @return: start resource id for success, and negative value for failure.
+ *
+ * This function check if the requested AI engine resource is available.
+ * If it is available, mark it used and return the start resource id.
+ */
+int aie_resource_get_region(struct aie_resource *res, u32 start, u32 count)
+{
+	unsigned long off;
+
+	if (!res || !res->bitmap || !count)
+		return -EINVAL;
+	off = bitmap_find_next_zero_area(res->bitmap, res->total, start,
+					 count, 0);
+	if (off >= res->total) {
+		pr_err("Failed to get available AI engine resource.\n");
+		return -ERANGE;
+	}
+	bitmap_set(res->bitmap, off, count);
+
+	return (int)off;
+}
+
+/**
+ * aie_resource_put_region() - release requested AI engine resource
+ * @res: pointer to AI engine resource to check
+ * @start: start index of the resource to release
+ * @count: number of elements to release
+ *
+ * This function release the requested AI engine resource.
+ */
+void aie_resource_put_region(struct aie_resource *res, int start, u32 count)
+{
+	if (!res || !count)
+		return;
+	bitmap_clear(res->bitmap, start, count);
+}
+
+/**
+ * aie_resource_set() - set the AI engine resource bits
+ * @res: pointer to AI engine resource
+ * @start: start bit to set
+ * @count: number of bits to set
+ * @return: 0 for success and negative value for failure
+ *
+ * This function sets the specified number bits in the resource.
+ */
+int aie_resource_set(struct aie_resource *res, u32 start, u32 count)
+{
+	if (!res || !res->bitmap || !count || start + count > res->total)
+		return -EINVAL;
+
+	bitmap_set(res->bitmap, start, count);
+	return 0;
+}
+
+/**
+ * aie_resource_cpy_from_arr32() - copies nbits from u32[] to bitmap.
+ * @res: pointer to AI engine resource
+ * @start: start bit in bitmap
+ * @src: source buffer
+ * @nbits: number of bits to copy from u32[]
+ * @return: 0 for success and negative value for failure
+ */
+int aie_resource_cpy_from_arr32(struct aie_resource *res, u32 start,
+				const u32 *src, u32 nbits)
+{
+	if (!res || !res->bitmap || !nbits || start + nbits  > res->total ||
+	    !src)
+		return -EINVAL;
+
+	bitmap_from_arr32(res->bitmap + BIT_WORD(start), src, nbits);
+	return 0;
+}
+
+/**
+ * aie_resource_cpy_to_arr32() - copies nbits to u32[] from bitmap.
+ * @res: pointer to AI engine resource
+ * @start: start bit in bitmap
+ * @dst: destination buffer
+ * @nbits: number of bits to copy to u32[]
+ * @return: 0 for success and negative value for failure
+ */
+int aie_resource_cpy_to_arr32(struct aie_resource *res, u32 start, u32 *dst,
+			      u32 nbits)
+{
+	if (!res || !res->bitmap || !nbits || start + nbits  > res->total ||
+	    !dst)
+		return -EINVAL;
+
+	bitmap_to_arr32(dst, res->bitmap + BIT_WORD(start), nbits);
+	return 0;
+}
+
+/**
+ * aie_resource_clear() - clear the AI engine resource bits
+ * @res: pointer to AI engine resource
+ * @start: start bit to set
+ * @count: number of bits to clear
+ * @return: 0 for success and negative value for failure
+ *
+ * This function clears the specified number bits in the resource.
+ */
+int aie_resource_clear(struct aie_resource *res, u32 start, u32 count)
+{
+	if (!res || !res->bitmap || !count || start + count > res->total)
+		return -EINVAL;
+
+	bitmap_clear(res->bitmap, start, count);
+	return 0;
+}
+
+/**
+ * aie_resource_clear_all() - clear all the AI engine resource bits
+ * @res: pointer to AI engine resource
+ * @return: 0 for success and negative value for failure
+ *
+ * This function clears all the bits in the resource.
+ */
+int aie_resource_clear_all(struct aie_resource *res)
+{
+	if (!res || !res->bitmap)
+		return -EINVAL;
+
+	bitmap_clear(res->bitmap, 0, res->total);
+	return 0;
+}
+
+/**
+ * aie_resource_testbit() - test if a bit is set in a AI engine resource
+ * @res: pointer to AI engine resource
+ * @bit: bit to check
+ * @return: true for set, false for not set
+ */
+bool aie_resource_testbit(struct aie_resource *res, u32 bit)
+{
+	if (!res || !res->bitmap || bit >= res->total)
+		return false;
+
+	/* Locate the unsigned long the required bit belongs to */
+	return test_bit(bit, res->bitmap);
+}
+
+/**
+ * aie_resource_check_common_avail() - check common available bits
+ *				       of two resources table
+ * @res0: pointer to AI engine resource0
+ * @res1: pointer to AI engine resource1
+ * @sbit: start bit to check
+ * @nbits: number of bits to check
+ * @return: number of common bits, or negative value for failure
+ */
+int aie_resource_check_common_avail(struct aie_resource *res0,
+				    struct aie_resource *res1,
+				    u32 sbit, u32 nbits)
+{
+	u32 ebit, avails;
+
+	if (!nbits || !res0 || !res1 || !res0->bitmap || !res1->bitmap ||
+	    (sbit + nbits) > res0->total || (sbit + nbits) > res1->total)
+		return -EINVAL;
+
+	ebit = sbit + nbits - 1;
+	avails = 0;
+	while (sbit <= ebit) {
+		unsigned long  *bitmap0, *bitmap1, tbits;
+		u32 tlbit, lbit = sbit % BITS_PER_LONG;
+		u32 lnbits = ebit - sbit + 1;
+
+		if (lnbits + lbit > BITS_PER_LONG)
+			lnbits = BITS_PER_LONG - lbit;
+
+		bitmap0 = &res0->bitmap[sbit / BITS_PER_LONG];
+		bitmap1 = &res1->bitmap[sbit / BITS_PER_LONG];
+		bitmap_or(&tbits, bitmap0, bitmap1, BITS_PER_LONG);
+		tlbit = lbit;
+		while (tlbit < lbit + lnbits) {
+			u32 b = bitmap_find_next_zero_area(&tbits,
+							   BITS_PER_LONG, tlbit,
+							   1, 0);
+			if (b >= lbit + lnbits)
+				break;
+			avails++;
+			tlbit = b + 1;
+		}
+		sbit += lnbits;
+	};
+
+	return avails;
+}
+
+/**
+ * aie_resource_get_common_avail() - get common available bits
+ *				     of two resources table
+ * @rres: pointer to AI engine runtime resource, runtime resource bitmap will
+ *	  be updated if the required resources are available.
+ * @sres: pointer to AI engine static resource, static resource bitmap will
+ *	  not be updated even if the required resources are available.
+ * @sbit: start bit to check
+ * @nbits: number of bits to get
+ * @total: total number of bits to check
+ * @rscs: resources array to return for resources ids
+ * @return: number of allocated bits for success, negative value for failure
+ */
+int aie_resource_get_common_avail(struct aie_resource *rres,
+				  struct aie_resource *sres,
+				  u32 sbit, u32 nbits, u32 total,
+				  struct aie_rsc *rscs)
+{
+	u32 ebit, tsbit, tnbits;
+
+	if (!nbits || !rres || !sres || !rres->bitmap || !sres->bitmap ||
+	    nbits > total || (sbit + total) > rres->total ||
+	    (sbit + total) > sres->total)
+		return -EINVAL;
+
+	ebit = sbit + total - 1;
+	tsbit = sbit;
+	tnbits = 0;
+	while (tsbit <= ebit && tnbits != nbits) {
+		unsigned long *rbitmap, *sbitmap, tbits;
+		u32 tlbit, lbit = tsbit % BITS_PER_LONG;
+		u32 lnbits = ebit - tsbit + 1;
+
+		if (lnbits + lbit > BITS_PER_LONG)
+			lnbits = BITS_PER_LONG - lbit;
+
+		rbitmap = &rres->bitmap[sbit / BITS_PER_LONG];
+		sbitmap = &sres->bitmap[sbit / BITS_PER_LONG];
+		bitmap_or(&tbits, rbitmap, sbitmap, BITS_PER_LONG);
+		tlbit = lbit;
+		while (tlbit < lbit + lnbits && tnbits != nbits) {
+			u32 b = bitmap_find_next_zero_area(&tbits,
+							   BITS_PER_LONG, tlbit,
+							   1, 0);
+			if (b >= lbit + lnbits)
+				break;
+			rscs[tnbits].id = tsbit - sbit + b - lbit;
+			tnbits++;
+			tlbit = b + 1;
+		}
+		tsbit += lnbits;
+	};
+
+	if (tnbits != nbits)
+		return -EINVAL;
+
+	while (tnbits--)
+		aie_resource_set(rres, sbit + rscs[tnbits].id, 1);
+
+	return nbits;
+}
+
+/**
+ * aie_resource_check_pattern_region() - check availability of requested
+ *					 contiguous resources of a pattern
+ * @res: pointer to AI engine resource to check
+ * @start: start index of the required resource
+ *	   It will check a continuous block of available resource starting from
+ *	   @start.
+ * @end: end index to check
+ * @count: number of requested element
+ * @return: start resource id if the requested number of resources are available
+ *	    It will return negative value of errors.
+ *
+ * This function will check the availability. It will return start resource id
+ * if the requested number of resources are available.
+ * The contiguous resources of a pattern is e.g.
+ * @count is 0, the resources starting from @start needs to be 0,1; or 2,3 and
+ * beyond
+ */
+int aie_resource_check_pattern_region(struct aie_resource *res,
+				      u32 start, u32 end, u32 count)
+{
+	unsigned long id;
+	u32 lstart;
+
+	if (!res || !res->bitmap || !count)
+		return -EINVAL;
+	lstart = start;
+	while (lstart < end) {
+		id = bitmap_find_next_zero_area(res->bitmap, res->total, lstart,
+						count, 0);
+		if (id + count > end + 1)
+			return -ERANGE;
+		else if (!((id - lstart) % count))
+			return (int)id;
+
+		lstart += count;
+	}
+
+	return -ERANGE;
+}
+
+/**
+ * aie_resource_check_common_pattern_region() - check common available region
+ *						of two resources table
+ * @res0: pointer to AI engine resource0
+ * @res1: pointer to AI engine resource1
+ * @sbit: start bit to check
+ * @nbits: number of bits to check
+ * @total: total number of bits to check
+ * @return: start bit of common region if it is found, negative value for
+ *	    failure
+ */
+int aie_resource_check_common_pattern_region(struct aie_resource *res0,
+					     struct aie_resource *res1,
+					     u32 sbit, u32 nbits, u32 total)
+{
+	int sbit0, sbit1;
+
+	if (!nbits || !res0 || !res1 || !res0->bitmap || !res1->bitmap ||
+	    nbits > total || (sbit + total) > res0->total ||
+	    (sbit + total) > res1->total)
+		return -EINVAL;
+
+	sbit0 = aie_resource_check_pattern_region(res0, sbit,
+						  sbit + total - 1, nbits);
+	if (sbit0 < 0)
+		return sbit0;
+
+	if ((u32)sbit0 + nbits > sbit + total)
+		return -EINVAL;
+
+	sbit1 = aie_resource_check_pattern_region(res1, sbit0,
+						  sbit0 + nbits - 1, nbits);
+	if (sbit1 != sbit0)
+		return -EINVAL;
+
+	return sbit1;
+}
+
+/**
+ * aie_resource_get_common_pattern_region() - get common available region
+ *					      of two resources table
+ * @res0: pointer to AI engine resource0
+ * @res1: pointer to AI engine resource1
+ * @sbit: start bit to check
+ * @nbits: number of bits to get
+ * @total: total number of bits to check
+ * @rscs: resources array to return for resources ids
+ * @return: start bit of the common region if it is found, negative value for
+ *	    failure
+ *
+ * The common pattern region is a contiguous block of resources which needs
+ * to be very number of @nbits.
+ * e.g. if nbits is 2, the offset to the start bit @sbit of returned resources
+ * needs to be: 0,1; 2,3 ...
+ */
+int aie_resource_get_common_pattern_region(struct aie_resource *res0,
+					   struct aie_resource *res1,
+					   u32 sbit, u32 nbits, u32 total,
+					   struct aie_rsc *rscs)
+{
+	int rsbit, ret;
+
+	rsbit = aie_resource_check_common_pattern_region(res0, res1, sbit,
+							 nbits, total);
+	if (rsbit < 0)
+		return rsbit;
+
+	ret = aie_resource_get_region(res0, rsbit, nbits);
+	if (ret < 0)
+		return ret;
+
+	if (ret != rsbit) {
+		aie_resource_put_region(res0, ret, nbits);
+		return -EINVAL;
+	}
+
+	ret = aie_resource_get_region(res1, rsbit, nbits);
+	if (ret < 0)
+		return ret;
+
+	if (ret != rsbit) {
+		aie_resource_put_region(res0, rsbit, nbits);
+		aie_resource_put_region(res1, ret, nbits);
+		return -EINVAL;
+	}
+
+	if (rscs) {
+		u32 i;
+
+		for (i = 0; i < nbits; i++, rscs++)
+			rscs->id = rsbit - sbit + i;
+	}
+
+	return rsbit;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-reset.c
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver resets implementation
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/io.h>
+
+#include "ai-engine-internal.h"
+
+/**
+ * aie_part_clear_core_regs_of_tile() - clear registers of aie core
+ * @apart: AI engine partition
+ * @loc: location of aie tile to clear
+ */
+static void aie_part_clear_core_regs_of_tile(struct aie_partition *apart,
+					     struct aie_location loc)
+{
+	struct aie_device *adev = apart->adev;
+	struct aie_aperture *aperture = apart->aperture;
+	const struct aie_core_regs_attr *regs = adev->core_regs;
+	u32 i;
+
+	for (i = 0; i < adev->num_core_regs; i++) {
+		u32 j, soff, eoff, reg;
+
+		soff = aie_cal_regoff(adev, loc, regs[i].core_regs->soff);
+		eoff = aie_cal_regoff(adev, loc, regs[i].core_regs->eoff);
+
+		for (reg = soff; reg <= eoff; reg += AIE_CORE_REGS_STEP) {
+			for (j = 0; j < regs[i].width; j++)
+				iowrite32(0, aperture->base + reg + j * 4);
+		}
+	}
+}
+
+/**
+ * aie_part_clear_core_regs - clear registers of aie core of a partition
+ * @apart: AI engine partition
+ */
+static void aie_part_clear_core_regs(struct aie_partition *apart)
+{
+	struct aie_range *range = &apart->range;
+	u32 c, r;
+
+	/* clear core registers for each tile in the partition */
+	for (c = range->start.col; c < range->start.col + range->size.col;
+			c++) {
+		for (r = range->start.row;
+				r < range->start.row + range->size.row; r++) {
+			struct aie_location loc;
+			u32 ttype;
+
+			loc.row = r;
+			loc.col = c;
+			ttype = apart->adev->ops->get_tile_type(apart->adev,
+								&loc);
+			if (ttype == AIE_TILE_TYPE_TILE &&
+			    aie_part_check_clk_enable_loc(apart, &loc))
+				aie_part_clear_core_regs_of_tile(apart, loc);
+		}
+	}
+}
+
+/**
+ * aie_part_clean() - reset and clear AI engine partition
+ * @apart: AI engine partition
+ * @return: 0 for success and negative value for failure
+ *
+ * This function will:
+ *  * gate all the columns
+ *  * reset AI engine partition columns
+ *  * reset AI engine shims
+ *  * clear the memories
+ *  * clear core registers
+ *  * gate all the tiles in a partition
+ *  * update clock state bitmap
+ *
+ * This function will not validate the partition, the caller will need to
+ * provide a valid AI engine partition.
+ */
+int aie_part_clean(struct aie_partition *apart)
+{
+	u32 node_id = apart->adev->pm_node_id;
+	int ret;
+
+	if (apart->cntrflag & XAIE_PART_NOT_RST_ON_RELEASE)
+		return 0;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_DIS_COL_CLK_BUFF);
+	if (ret < 0)
+		return ret;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_COL_RST |
+				      XILINX_AIE_OPS_SHIM_RST);
+	if (ret < 0)
+		return ret;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_ENB_COL_CLK_BUFF);
+	if (ret < 0)
+		return ret;
+
+	apart->adev->ops->mem_clear(apart);
+	aie_part_clear_core_regs(apart);
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_DIS_COL_CLK_BUFF);
+	if (ret < 0)
+		return ret;
+
+	aie_resource_clear_all(&apart->cores_clk_state);
+
+	return 0;
+}
+
+/**
+ * aie_part_reset() - reset AI engine partition
+ * @apart: AI engine partition
+ * @return: 0 for success and negative value for failure
+ *
+ * This function will:
+ * - gate all the columns
+ * - reset AI engine partition columns
+ * - ungate all the columns
+ * - reset AI engine shims
+ * - gate all the tiles in a partition.
+ *
+ * This function will not validate the partition, the caller will need to
+ * provide a valid AI engine partition.
+ */
+int aie_part_reset(struct aie_partition *apart)
+{
+	u32 node_id = apart->adev->pm_node_id;
+	int ret;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret)
+		return ret;
+
+	/*
+	 * Check if any AI engine memories or registers in the
+	 * partition have been mapped. If yes, don't reset.
+	 */
+	if (aie_part_has_mem_mmapped(apart) ||
+	    aie_part_has_regs_mmapped(apart)) {
+		dev_err(&apart->dev,
+			"failed to reset, there are mmapped memories or registers.\n");
+		mutex_unlock(&apart->mlock);
+		return -EBUSY;
+	}
+
+	/* Clear tiles in use bitmap and clock state bitmap */
+	aie_resource_clear_all(&apart->tiles_inuse);
+	aie_resource_clear_all(&apart->cores_clk_state);
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_DIS_COL_CLK_BUFF);
+	if (ret < 0)
+		goto exit;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_COL_RST);
+	if (ret < 0)
+		goto exit;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_ENB_COL_CLK_BUFF);
+	if (ret < 0)
+		goto exit;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_SHIM_RST);
+	if (ret < 0)
+		goto exit;
+
+	ret = zynqmp_pm_aie_operation(node_id, apart->range.start.col,
+				      apart->range.size.col,
+				      XILINX_AIE_OPS_DIS_COL_CLK_BUFF);
+	if (ret < 0)
+		goto exit;
+
+	aie_part_clear_cached_events(apart);
+	aie_part_rscmgr_reset(apart);
+
+exit:
+	mutex_unlock(&apart->mlock);
+
+	return ret;
+}
+
+/**
+ * aie_part_post_reinit() - AI engine partition has been re-initialized
+ * @apart: AI engine partition
+ * @return: 0 for success and negative value for failure
+ *
+ * This function will:
+ * - scan which tiles are gated
+ * - update memories and registers mapping
+ *
+ * This function will scan which tiles are gated, and update the memories and
+ * registers setting. This function is called after the AI engine partition is
+ * reconfigured with PDI outside the AI engine driver.
+ */
+int aie_part_post_reinit(struct aie_partition *apart)
+{
+	int ret;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret)
+		return ret;
+
+	ret = aie_part_scan_clk_state(apart);
+	mutex_unlock(&apart->mlock);
+	if (ret) {
+		dev_err(&apart->dev,
+			"failed to scan clock states after reset is done.\n");
+		return ret;
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-rscmgr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-rscmgr.c
@@ -0,0 +1,1652 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine partition resource manager
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+
+#include "ai-engine-internal.h"
+#include <linux/slab.h>
+
+/*
+ * Macros for the AI engine resource bitmap element header
+ */
+#define AIE_RSC_BITMAP_TILETYPE_BITSHIFT	0U
+#define AIE_RSC_BITMAP_TILETYPE_BITWIDTH	4U
+#define AIE_RSC_BITMAP_MODTYPE_BITSHIFT		4U
+#define AIE_RSC_BITMAP_MODTYPE_BITWIDTH		4U
+#define AIE_RSC_BITMAP_RSCTYPE_BITSHIFT		8U
+#define AIE_RSC_BITMAP_RSCTYPE_BITWIDTH		8U
+#define AIE_RSC_BITMAP_LENU64_BITSHIFT		16U
+#define AIE_RSC_BITMAP_LENU64_BITWIDTH		32U
+
+#define AIE_RSC_BITMAP_GEN_MASK(N) \
+	GENMASK_ULL((AIE_RSC_BITMAP_##N ##_BITSHIFT + \
+		     AIE_RSC_BITMAP_##N ##_BITWIDTH - 1), \
+		    AIE_RSC_BITMAP_##N ##_BITSHIFT)
+#define AIE_RSC_BITMAP_TILETYPE_MASK	AIE_RSC_BITMAP_GEN_MASK(TILETYPE)
+#define AIE_RSC_BITMAP_MODTYPE_MASK	AIE_RSC_BITMAP_GEN_MASK(MODTYPE)
+#define AIE_RSC_BITMAP_RSCTYPE_MASK	AIE_RSC_BITMAP_GEN_MASK(RSCTYPE)
+#define AIE_RSC_BITMAP_LENU64_MASK	AIE_RSC_BITMAP_GEN_MASK(LENU64)
+
+#define AIE_RSC_BITMAP_HEAD_VAL(N, v) \
+	(((v) & AIE_RSC_BITMAP_##N ##_MASK) >> AIE_RSC_BITMAP_##N ##_BITSHIFT)
+
+/*
+ * enum for AI engine resource bitmap allocation types
+ */
+enum aie_rsc_alloc_type {
+	AIE_RSC_ALLOC_STATIC = 0,
+	AIE_RSC_ALLOC_AVAIL = 1,
+	AIE_RSC_ALLOC_MAX = 2
+};
+
+/**
+ * struct aie_rsc_meta_header - struct of a resource bitmaps meta data header
+ * @stat: statistics information of the bitmaps, such as number of bitmaps
+ * @bitmap_off: offset to the start of the binary of the first bitmap element
+ */
+struct aie_rsc_meta_header {
+	u64 stat;
+	u64 bitmap_off;
+};
+
+/**
+ * struct aie_rsc_bitmap - struct of a resource bitmap element
+ * @header: bitmap header, it contains the following information:
+ *	    tile type, module type, resource type, and the bitmap
+ *	    length.
+ * @bitmap: the pointer of bitmap
+ */
+struct aie_rsc_bitmap {
+	u64 header;
+	u64 bitmap[0];
+};
+
+/**
+ * aie_dev_get_tile_attr - helper function to get tile attributes
+ * @adev: AI engine device
+ * @ttype: tile type
+ * @return: attributes of an AI engine tile type
+ */
+static inline
+struct aie_tile_attr *aie_dev_get_tile_attr(struct aie_device *adev,
+					    enum aie_tile_type ttype)
+{
+	return &adev->ttype_attr[ttype];
+}
+
+/**
+ * aie_dev_get_tile_rsc_attr - helper function to get resource attribute of a
+ *			       tile type of an AI engine device
+ * @adev: AI engine device
+ * @ttype: tile type
+ * @rtype: resource type
+ * @return: attributes of an AI engine resource type of a tile type
+ */
+static inline const
+struct aie_tile_rsc_attr *aie_dev_get_tile_rsc_attr(struct aie_device *adev,
+						    enum aie_tile_type ttype,
+						    enum aie_rsc_type rtype)
+{
+	return &adev->ttype_attr[ttype].rscs_attr[rtype];
+}
+
+/**
+ * aie_dev_get_mod_id - helper function to get module id of a module of a tile
+ *			type. The module ID can be used to indexing the resource
+ *			attributes of a module type of a tile type or indexing
+ *			resource status bitmaps.
+ *
+ * @adev: AI engine device
+ * @ttype: tile type
+ * @mod: module type
+ * @return: module type index
+ */
+static int aie_dev_get_mod_id(struct aie_device *adev,
+			      enum aie_tile_type ttype,
+			      enum aie_module_type mod)
+{
+	struct aie_tile_attr *tattr = &adev->ttype_attr[ttype];
+
+	int ret;
+
+	if (ttype == AIE_TILE_TYPE_TILE)
+		ret = AIE_MOD_ID(TILE, mod);
+	else if (ttype == AIE_TILE_TYPE_SHIMPL)
+		ret = AIE_MOD_ID(SHIMPL, mod);
+	else
+		ret = AIE_MOD_ID(SHIMNOC, mod);
+
+	if (ret < 0 || ret > tattr->num_mods)
+		return -EINVAL;
+
+	return ret;
+}
+
+/**
+ * aie_dev_get_mod_rsc_attr - helper function to get resource attribute of a
+ *			      module of an AI engine device
+ * @adev: AI engine device
+ * @ttype: tile type
+ * @mod: module type
+ * @rtype: resource type
+ * @return: module type resource attributes
+ */
+static const
+struct aie_mod_rsc_attr *aie_dev_get_mod_rsc_attr(struct aie_device *adev,
+						  enum aie_tile_type ttype,
+						  enum aie_module_type mod,
+						  enum aie_rsc_type rtype)
+{
+	const struct aie_tile_rsc_attr *rsc = aie_dev_get_tile_rsc_attr(adev,
+									ttype,
+									rtype);
+	const struct aie_mod_rsc_attr *mrsc = NULL;
+	int mod_id = aie_dev_get_mod_id(adev, ttype, mod);
+
+	if (mod_id < 0)
+		return NULL;
+
+	mrsc = &rsc->mod_attr[mod_id];
+	if (mrsc && !mrsc->num_rscs)
+		return NULL;
+
+	return mrsc;
+}
+
+/**
+ * aie_part_get_ttype_rsc_bitmaps - helper function to get bitmap of a resource
+ *				    with tile type, module type, and resource
+ *				    type
+ *
+ * @apart: AI engine partition
+ * @ttype: tile type
+ * @mod: module type
+ * @rtype: resource type
+ * @return: pointer to AI engine resource status bitmaps if resource is found,
+ *	    otherwise NULL
+ */
+static
+struct aie_rsc_stat *aie_part_get_ttype_rsc_bitmaps(struct aie_partition *apart,
+						    enum aie_tile_type ttype,
+						    enum aie_module_type mod,
+						    enum aie_rsc_type rtype)
+{
+	int mod_id;
+	struct aie_mod_rscs *mrscs;
+
+	if (ttype >= AIE_TILE_TYPE_MAX)
+		return NULL;
+
+	mod_id = aie_dev_get_mod_id(apart->adev, ttype, mod);
+	if (mod_id < 0)
+		return NULL;
+
+	if (rtype >= AIE_RSCTYPE_MAX)
+		return NULL;
+
+	mrscs = apart->trscs[ttype].mod_rscs[rtype];
+	if (!mrscs)
+		return NULL;
+
+	return mrscs[mod_id].rscs_stat;
+}
+
+/**
+ * aie_part_get_rsc_bitmaps - helper function to get bitmap of a resource
+ *
+ * @apart: AI engine partition
+ * @loc: tile location
+ * @mod: module type
+ * @rtype: resource type
+ * @return: pointer to AI engine resource status bitmaps if resource is found,
+ *	    otherwise NULL
+ */
+static
+struct aie_rsc_stat *aie_part_get_rsc_bitmaps(struct aie_partition *apart,
+					      struct aie_location loc,
+					      enum aie_module_type mod,
+					      enum aie_rsc_type rtype)
+{
+	u32 ttype = apart->adev->ops->get_tile_type(apart->adev, &loc);
+
+	return aie_part_get_ttype_rsc_bitmaps(apart, ttype, mod, rtype);
+}
+
+/**
+ * aie_part_get_mod_num_rscs - helper function to get number of resources
+ *			       of a module of a tile
+ *
+ * @apart: AI engine partition
+ * @loc: tile location
+ * @mod: module type
+ * @rtype: resource type
+ * @return: number of max resources of a module of a tile
+ */
+static
+int aie_part_get_mod_num_rscs(struct aie_partition *apart,
+			      struct aie_location loc,
+			      enum aie_module_type mod,
+			      enum aie_rsc_type rtype)
+{
+	u32 ttype = apart->adev->ops->get_tile_type(apart->adev, &loc);
+	const struct aie_mod_rsc_attr *mattr;
+
+	mattr = aie_dev_get_mod_rsc_attr(apart->adev, ttype, mod, rtype);
+	if (!mattr)
+		return 0;
+
+	return mattr->num_rscs;
+}
+
+/**
+ * aie_part_get_rsc_startbit - helper function to get the start bit of a
+ *			       resource of a module of a tile.
+ *
+ * @apart: AI engine partition
+ * @loc: tile location
+ * @mod: module type
+ * @rtype: resource type
+ * @return: pointer to AI engine resource status bitmaps if resource is found,
+ *	    otherwise NULL
+ *
+ */
+static
+int aie_part_get_rsc_startbit(struct aie_partition *apart,
+			      struct aie_location loc,
+			      enum aie_module_type mod,
+			      enum aie_rsc_type rtype)
+{
+	struct aie_device *adev = apart->adev;
+	u32 ttype;
+	const struct aie_mod_rsc_attr *mattr;
+	int num_rows;
+	struct aie_tile_attr *tattr;
+
+	ttype = adev->ops->get_tile_type(adev, &loc);
+
+	mattr = aie_dev_get_mod_rsc_attr(adev, ttype, mod, rtype);
+	if (!mattr)
+		return -EINVAL;
+
+	num_rows = aie_part_get_tile_rows(apart, ttype);
+	tattr = &adev->ttype_attr[ttype];
+	return mattr->num_rscs *
+	       ((loc.col - apart->range.start.col) * num_rows +
+		loc.row - tattr->start_row);
+}
+
+/**
+ * aie_part_adjust_loc - adjust relative tile location to partition to
+ *			 absolute location in AI engine device
+ * @apart: AI engine partition
+ * @rloc: relative location in AI engine partition
+ * @loc: returns absolute location in AI engine device
+ * @return: 0 for success, negative value for failure
+ */
+static
+int aie_part_adjust_loc(struct aie_partition *apart,
+			struct aie_location rloc, struct aie_location *loc)
+{
+	if (aie_validate_location(apart, rloc) < 0) {
+		dev_err(&apart->dev,
+			"invalid loc (%u,%u) in (%u,%u).\n",
+			rloc.col, rloc.row,
+			apart->range.size.col, apart->range.size.row);
+		return -EINVAL;
+	}
+
+	loc->col = rloc.col + apart->range.start.col;
+	loc->row = rloc.row + apart->range.start.row;
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_init() - initialize AI engine partition resource status
+ *			    bitmaps
+ * @apart: AI engine partition
+ * @return: 0 for success, negative value for failure.
+ *
+ * This function will create the hardware resources status bitmaps for the whole
+ * partition.
+ * Each partition contains an array of hardware resources status bitmaps of all
+ * defined tiles types.:
+ * aie_partition
+ *   |- trscs[<all_tile_types>]
+ *       |-mod_rscs[<all_resources_types>]
+ *         |-rscs_stat - resources status bitmaps of a module type of a tile
+ *			 type of the AI engine partition.
+ */
+int aie_part_rscmgr_init(struct aie_partition *apart)
+{
+	struct aie_device *adev = apart->adev;
+	u32 t;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "Skipping rsc mgr init.\n");
+		return 0;
+	}
+
+	for (t = AIE_TILE_TYPE_TILE; t < AIE_TILE_TYPE_MAX; t++) {
+		struct aie_tile_rscs *trscs = &apart->trscs[t];
+		struct aie_tile_attr *tattr;
+		int num_rows, num_cols;
+		u32 r;
+
+		/*
+		 * SHIMNOC tile resource bitmaps reuse the SHIMPL resource
+		 * bitmaps. In future, for DMA resources, SHIMNOC tile will
+		 * have DMA resources bitmap which will be the unique to
+		 * SHIMNOC tiles.
+		 */
+		if (t == AIE_TILE_TYPE_SHIMNOC) {
+			*trscs = apart->trscs[AIE_TILE_TYPE_SHIMPL];
+			continue;
+		}
+
+		/*
+		 * Get the number of rows of a tile type and the number
+		 * of columns of the partition, which will be used to
+		 * calculate the size of the bitmap is a resource.
+		 */
+		tattr = aie_dev_get_tile_attr(adev, t);
+		num_rows = aie_part_get_tile_rows(apart, t);
+		num_cols = apart->range.size.col;
+
+		for (r = AIE_RSCTYPE_PERF; r < AIE_RSCTYPE_MAX; r++) {
+			const struct aie_tile_rsc_attr *trsc_attr;
+			struct aie_mod_rscs *mod_rscs;
+			u32 m;
+
+			trsc_attr = aie_dev_get_tile_rsc_attr(adev, t, r);
+			if (!trsc_attr)
+				continue;
+
+			mod_rscs = kcalloc(tattr->num_mods,
+					   sizeof(*mod_rscs), GFP_KERNEL);
+			if (!mod_rscs) {
+				aie_part_rscmgr_finish(apart);
+				return -ENOMEM;
+			}
+
+			trscs->mod_rscs[r] = mod_rscs;
+			for (m = 0 ; m < tattr->num_mods; m++) {
+				struct aie_rsc_stat *rscs_stat;
+				int num_mrscs = trsc_attr->mod_attr[m].num_rscs;
+				int ret, total_rscs;
+
+				/*
+				 * if number of resources of this module type in
+				 * this tile type is 0, skip allocating bitmap
+				 * for the resource of this module type.
+				 */
+				if (!num_mrscs)
+					continue;
+
+				rscs_stat = kzalloc(sizeof(*rscs_stat),
+						    GFP_KERNEL);
+				if (!rscs_stat) {
+					aie_part_rscmgr_finish(apart);
+					return -ENOMEM;
+				}
+
+				mod_rscs[m].rscs_stat = rscs_stat;
+				total_rscs = num_mrscs * num_rows * num_cols;
+				/*
+				 * initialize bitmaps for static resources and
+				 * runtime allocated resources.
+				 */
+				ret = aie_resource_initialize(&rscs_stat->rbits,
+							      total_rscs);
+				if (ret) {
+					aie_part_rscmgr_finish(apart);
+					return ret;
+				}
+				ret = aie_resource_initialize(&rscs_stat->sbits,
+							      total_rscs);
+				if (ret) {
+					aie_part_rscmgr_finish(apart);
+					return ret;
+				}
+			}
+		}
+	}
+
+	/* Reserve resources for interrupts */
+	return aie_part_set_intr_rscs(apart);
+}
+
+/**
+ * aie_part_rscmgr_finish() - uninitialize AI engine partition resource status
+ *			      bitmaps.
+ * @apart: AI engine partition
+ */
+void aie_part_rscmgr_finish(struct aie_partition *apart)
+{
+	struct aie_device *adev = apart->adev;
+	u32 t;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return;
+	}
+
+	for (t = AIE_TILE_TYPE_TILE; t < AIE_TILE_TYPE_MAX; t++) {
+		struct aie_tile_rscs *trscs = &apart->trscs[t];
+		struct aie_tile_attr *tattr;
+		u32 r;
+
+		/* SHIMNOC reuses SHIMPL resources bitmap */
+		if (t == AIE_TILE_TYPE_SHIMNOC)
+			continue;
+
+		tattr = aie_dev_get_tile_attr(adev, t);
+		for (r = AIE_RSCTYPE_PERF; r < AIE_RSCTYPE_MAX; r++) {
+			struct aie_mod_rscs *mod_rscs;
+			u32 m;
+
+			mod_rscs = trscs->mod_rscs[r];
+			if (!mod_rscs)
+				continue;
+
+			for (m = 0 ; m < tattr->num_mods; m++) {
+				struct aie_rsc_stat *rscs_stat;
+
+				rscs_stat = mod_rscs[m].rscs_stat;
+				if (!rscs_stat)
+					continue;
+
+				aie_resource_uninitialize(&rscs_stat->rbits);
+				aie_resource_uninitialize(&rscs_stat->sbits);
+				kfree(rscs_stat);
+			}
+
+			kfree(mod_rscs);
+			trscs->mod_rscs[r] = NULL;
+		}
+	}
+}
+
+/**
+ * aie_part_rscmgr_reset() - reset AI engine partition resource status bitmaps
+ *
+ * @apart: AI engine partition
+ *
+ * This function expect caller to lock the partition before calling this
+ * function.
+ */
+void aie_part_rscmgr_reset(struct aie_partition *apart)
+{
+	struct aie_device *adev = apart->adev;
+	u32 t;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return;
+	}
+
+	for (t = AIE_TILE_TYPE_TILE; t < AIE_TILE_TYPE_MAX; t++) {
+		struct aie_tile_rscs *trscs = &apart->trscs[t];
+		struct aie_tile_attr *tattr;
+		u32 r;
+
+		/* SHIMNOC reuses SHIMPL resources bitmap */
+		if (t == AIE_TILE_TYPE_SHIMNOC)
+			continue;
+
+		tattr = aie_dev_get_tile_attr(adev, t);
+		for (r = AIE_RSCTYPE_PERF; r < AIE_RSCTYPE_MAX; r++) {
+			struct aie_mod_rscs *mod_rscs;
+			u32 m;
+
+			mod_rscs = trscs->mod_rscs[r];
+			if (!mod_rscs)
+				continue;
+
+			for (m = 0 ; m < tattr->num_mods; m++) {
+				struct aie_rsc_stat *rscs_stat;
+
+				rscs_stat = mod_rscs[m].rscs_stat;
+				if (!rscs_stat)
+					continue;
+
+				aie_resource_clear_all(&rscs_stat->rbits);
+				aie_resource_clear_all(&rscs_stat->sbits);
+			}
+		}
+	}
+
+	/* Always reserve resources for interrupt */
+	(void)aie_part_set_intr_rscs(apart);
+}
+
+/**
+ * aie_part_rscmgr_rsc_req() - request a type of resource from a module of a
+ *			       tile of an AI engine partition
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource request arguments
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will check if there the specified number of free resources
+ * available. If yes, allocated the specified number of resources.
+ */
+long aie_part_rscmgr_rsc_req(struct aie_partition *apart,
+			     void __user *user_args)
+{
+	struct aie_rsc_req_rsp args;
+	struct aie_location loc;
+	struct aie_rsc_stat *rstat;
+	long ret;
+	int mod_num_rscs, start_bit;
+	struct aie_rsc *rscs;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	if (!args.rscs) {
+		dev_err(&apart->dev,
+			"invalid resource request, empty resources list.\n");
+		return -EINVAL;
+	}
+
+	ret = aie_part_adjust_loc(apart, args.req.loc, &loc);
+	if (ret < 0)
+		return ret;
+
+	if (args.req.type > AIE_RSCTYPE_MAX) {
+		dev_err(&apart->dev,
+			"invalid resource request, invalid resource type %d.\n",
+			args.req.type);
+		return -EINVAL;
+	}
+
+	rstat = aie_part_get_rsc_bitmaps(apart, loc, args.req.mod,
+					 args.req.type);
+	start_bit = aie_part_get_rsc_startbit(apart, loc, args.req.mod,
+					      args.req.type);
+	if (!rstat || start_bit < 0) {
+		dev_err(&apart->dev,
+			"invalid resource request(%u,%u), mod:%u, rsc:%u.\n",
+			args.req.loc.col, args.req.loc.row, args.req.mod,
+			args.req.type);
+		return -EINVAL;
+	}
+
+	mod_num_rscs = aie_part_get_mod_num_rscs(apart, loc, args.req.mod,
+						 args.req.type);
+	if (!args.req.num_rscs || args.req.num_rscs > mod_num_rscs) {
+		dev_err(&apart->dev,
+			"invalid resource req(%u,%u),mod:%u,rsc:%u,expect=%u,max=%u.\n",
+			args.req.loc.col, args.req.loc.row, args.req.mod,
+			args.req.type, args.req.num_rscs, mod_num_rscs);
+		return -EINVAL;
+	}
+
+	rscs = kmalloc_array(args.req.num_rscs, sizeof(*rscs), GFP_KERNEL);
+	if (!rscs)
+		return -ENOMEM;
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(rscs);
+		return ret;
+	}
+
+	/*
+	 * There can be some resources needs to be contiguous, such as combo events.
+	 * It needs to be 0,1; 2,3; or 0,1,2; or 0,1,2,3
+	 */
+	if (!(args.req.flag & XAIE_RSC_PATTERN_BLOCK)) {
+		ret = aie_resource_get_common_avail(&rstat->rbits, &rstat->sbits,
+						    start_bit,
+						    args.req.num_rscs,
+						    mod_num_rscs, rscs);
+	} else {
+		ret = aie_resource_get_common_pattern_region(&rstat->rbits,
+							     &rstat->sbits,
+							     start_bit,
+							     args.req.num_rscs,
+							     mod_num_rscs,
+							     rscs);
+	}
+	mutex_unlock(&apart->mlock);
+
+	if (ret < 0) {
+		if (!(args.req.flag & XAIE_RSC_PATTERN_BLOCK)) {
+			dev_warn(&apart->dev,
+				 "invalid resource req(%u,%u),mod:%u,rsc:%u,expect=%u not avail.\n",
+				args.req.loc.col, args.req.loc.row,
+				args.req.mod, args.req.type,
+				args.req.num_rscs);
+		} else {
+			dev_warn(&apart->dev,
+				 "invalid contiguous resource req(%u,%u),mod:%u,rsc:%u,expect=%u not avail.\n",
+				args.req.loc.col, args.req.loc.row,
+				args.req.mod, args.req.type, args.req.num_rscs);
+		}
+		kfree(rscs);
+		return ret;
+	}
+
+	if (copy_to_user((void __user *)args.rscs, rscs,
+			 sizeof(*rscs) * args.req.num_rscs))
+		ret = -EFAULT;
+	else
+		ret = 0;
+
+	kfree(rscs);
+	return ret;
+}
+
+/**
+ * aie_part_rscmgr_rsc_clearbit() - clear resource status of a module of a
+ *				    tile of an AI engine partition
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource release arguments
+ * @is_release: true to clear the status from both runtime and static bitmaps
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will clear the status of a resource of both runtime status
+ * bitmap and static status bitmap or both based on the @is_release setting.
+ */
+static long aie_part_rscmgr_rsc_clearbit(struct aie_partition *apart,
+					 void __user *user_args,
+					 bool is_release)
+{
+	struct aie_rsc args;
+	struct aie_location loc, rloc;
+	struct aie_rsc_stat *rstat;
+	long ret;
+	int mod_num_rscs, start_bit;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	rloc.col = (u32)(args.loc.col & 0xFF);
+	rloc.row = (u32)(args.loc.row & 0xFF);
+	ret = aie_part_adjust_loc(apart, rloc, &loc);
+	if (ret < 0)
+		return ret;
+
+	if (args.type > AIE_RSCTYPE_MAX) {
+		dev_err(&apart->dev,
+			"invalid resource to release, invalid resource type %d.\n",
+			args.type);
+		return -EINVAL;
+	}
+
+	rstat = aie_part_get_rsc_bitmaps(apart, loc, args.mod, args.type);
+	start_bit = aie_part_get_rsc_startbit(apart, loc, args.mod,
+					      args.type);
+	if (!rstat || start_bit < 0) {
+		dev_err(&apart->dev,
+			"invalid resource to release(%u,%u),mod:%u,rsc:%u.\n",
+			rloc.col, rloc.row, args.mod, args.type);
+		return -EINVAL;
+	}
+
+	mod_num_rscs = aie_part_get_mod_num_rscs(apart, loc, args.mod,
+						 args.type);
+	if (args.id > mod_num_rscs) {
+		dev_err(&apart->dev,
+			"invalid resource to release(%u,%u),mod:%u,rsc:%u,id=%u.\n",
+			rloc.col, rloc.row, args.mod, args.type, args.id);
+		return -EINVAL;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret)
+		return ret;
+
+	if (!aie_resource_testbit(&rstat->rbits, start_bit + args.id)) {
+		dev_err(&apart->dev,
+			"invalid resource to release(%u,%u),mod:%u,rsc:%u,id=%u. not requested\n",
+			rloc.col, rloc.row, args.mod, args.type, args.id);
+		mutex_unlock(&apart->mlock);
+		return -EINVAL;
+	}
+
+	aie_resource_clear(&rstat->rbits, start_bit + args.id, 1);
+	if (is_release)
+		aie_resource_clear(&rstat->sbits, start_bit + args.id, 1);
+
+	mutex_unlock(&apart->mlock);
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_rsc_release() - release resource of a module of a tile of
+ *				   an AI engine partition
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource releasearguments
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will clear the bit of the resource runtime and static status
+ * bitmap.
+ */
+long aie_part_rscmgr_rsc_release(struct aie_partition *apart,
+				 void __user *user_args)
+{
+	return aie_part_rscmgr_rsc_clearbit(apart, user_args, true);
+}
+
+/**
+ * aie_part_rscmgr_rsc_free() - free resource of a module of a tile of an AI
+ *				engine partition
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource free arguments
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will clear the bit of the resource runtime status bitmap.
+ */
+long aie_part_rscmgr_rsc_free(struct aie_partition *apart,
+			      void __user *user_args)
+{
+	return aie_part_rscmgr_rsc_clearbit(apart, user_args, false);
+}
+
+/**
+ * aie_part_rscmgr_rsc_req_specific() - request for specific resource of a
+ *					module of a tile of an AI engine
+ *					partition
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource free arguments
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function requires the specified resource is set in the static
+ * status bitmap
+ */
+long aie_part_rscmgr_rsc_req_specific(struct aie_partition *apart,
+				      void __user *user_args)
+{
+	struct aie_rsc args;
+	struct aie_location loc, rloc;
+	struct aie_rsc_stat *rstat;
+	long ret;
+	int mod_num_rscs, start_bit;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	rloc.col = (u32)(args.loc.col & 0xFF);
+	rloc.row = (u32)(args.loc.row & 0xFF);
+	ret = aie_part_adjust_loc(apart, rloc, &loc);
+	if (ret < 0)
+		return ret;
+
+	if (args.type > AIE_RSCTYPE_MAX) {
+		dev_err(&apart->dev,
+			"invalid resource to request, invalid resource type %d.\n",
+			args.type);
+		return -EINVAL;
+	}
+
+	rstat = aie_part_get_rsc_bitmaps(apart, loc, args.mod, args.type);
+	start_bit = aie_part_get_rsc_startbit(apart, loc, args.mod,
+					      args.type);
+	if (!rstat || start_bit < 0) {
+		dev_err(&apart->dev,
+			"invalid resource to request(%u,%u),mod:%u,rsc:%u.\n",
+			rloc.col, rloc.row, args.mod, args.type);
+		return -EINVAL;
+	}
+
+	mod_num_rscs = aie_part_get_mod_num_rscs(apart, loc, args.mod,
+						 args.type);
+	if (args.id > mod_num_rscs) {
+		dev_err(&apart->dev,
+			"invalid resource to request(%u,%u),mod:%u, rsc:%u,id=%u.\n",
+			rloc.col, rloc.row, args.mod, args.type, args.id);
+		return -EINVAL;
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret)
+		return ret;
+
+	/* Check if the resource is in the runtime status bitmap */
+	if (aie_resource_testbit(&rstat->rbits, start_bit + args.id)) {
+		dev_err(&apart->dev,
+			"invalid resource to request(%u,%u),mod:%u,rsc:%u,id=%u, resource in use.\n",
+			rloc.col, rloc.row, args.mod, args.type, args.id);
+		mutex_unlock(&apart->mlock);
+		return -EBUSY;
+	}
+
+	aie_resource_set(&rstat->rbits, start_bit + args.id, 1);
+
+	mutex_unlock(&apart->mlock);
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_rsc_check_avail() - check how many resources vailable for
+ *				       the specified resource type
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource free arguments
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function requires the specified resource is set in the static
+ * status bitmap
+ */
+long aie_part_rscmgr_rsc_check_avail(struct aie_partition *apart,
+				     void __user *user_args)
+{
+	struct aie_rsc_stat *rstat;
+	struct aie_location loc;
+	long ret;
+	int mod_num_rscs, start_bit;
+	struct aie_rsc_req args;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	ret = aie_part_adjust_loc(apart, args.loc, &loc);
+	if (ret < 0)
+		return ret;
+
+	if (args.type > AIE_RSCTYPE_MAX) {
+		dev_err(&apart->dev,
+			"invalid resource to request, invalid resource type %d.\n",
+			args.type);
+		return -EINVAL;
+	}
+
+	rstat = aie_part_get_rsc_bitmaps(apart, loc, args.mod, args.type);
+	start_bit = aie_part_get_rsc_startbit(apart, loc, args.mod,
+					      args.type);
+	if (!rstat || start_bit < 0) {
+		dev_err(&apart->dev,
+			"invalid resource to request(%u,%u),mod:%u,rsc:%u.\n",
+			args.loc.col, args.loc.row, args.mod, args.type);
+		return -EINVAL;
+	}
+
+	mod_num_rscs = aie_part_get_mod_num_rscs(apart, loc, args.mod,
+						 args.type);
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret)
+		return ret;
+
+	args.num_rscs = aie_resource_check_common_avail(&rstat->rbits,
+							&rstat->sbits,
+							start_bit,
+							mod_num_rscs);
+	mutex_unlock(&apart->mlock);
+
+	if (copy_to_user(user_args, &args, sizeof(args)))
+		return -EFAULT;
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_get_ungated_bc_mods() - find the ungated modules of the full
+ *					   partition and fill in the locations
+ *					   information to the resources array.
+ * @apart: AI engine partition
+ * @num_rscs: number of broadcast resources, each module of a tile has a
+ *	      broadcast resource in this array.
+ * @onum_rscs: returns the number of actual ungated broadcast resources of the
+ *	       whole partition.
+ *
+ * @rscs: broadcast resources array
+ * @return: 0 for success, negative value for failure
+ */
+static int aie_part_rscmgr_get_ungated_bc_mods(struct aie_partition *apart,
+					       u32 num_rscs, u32 *onum_rscs,
+					       struct aie_rsc *rscs)
+{
+	struct aie_device *adev = apart->adev;
+	u32 c, r, i = 0;
+
+	for (c = 0; c < apart->range.size.col; c++) {
+		for (r = 0; r < apart->range.size.row; r++) {
+			struct aie_location l;
+			u32 ttype, m;
+			const struct aie_tile_attr *tattr;
+			const struct aie_tile_rsc_attr *rattr;
+			enum aie_rsc_type rtype = AIE_RSCTYPE_BROADCAST;
+
+			l.col = apart->range.start.col + c;
+			l.row = r;
+			ttype = adev->ops->get_tile_type(adev, &l);
+			tattr = &adev->ttype_attr[ttype];
+			rattr = &tattr->rscs_attr[rtype];
+			for (m = 0; m < tattr->num_mods; m++) {
+				/*
+				 * if module doesn't have broadcast channel,
+				 * skipped. This is not the case today.
+				 */
+				if (!rattr->mod_attr[m].num_rscs)
+					continue;
+				/* Check if the broadcast resource is gated */
+				if (aie_part_check_clk_enable_loc(apart, &l)) {
+					if (i >= num_rscs) {
+						dev_err(&apart->dev,
+							"failed to returns all ungated tiles, not enough resource elements.\n");
+						return -EINVAL;
+					}
+					rscs[i].loc.col = (u8)(c & 0xFF);
+					rscs[i].loc.row = (u8)(r & 0xFF);
+					rscs[i].mod = tattr->mods[m];
+					i++;
+				}
+			}
+		}
+	}
+
+	*onum_rscs = i;
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_get_or_bc_stat() - get OR the broadcast resources stat of
+ *				      specified modules in the specified
+ *				      resources array.
+ *
+ * @apart: AI engine partition
+ * @num_rscs: number of broadcast resources, every module has one broadcast
+ *	      resource
+ * @rscs: array of broadcast resources, each element contains the tile
+ *	  location and module information of the broadcast channel
+ * @runtime_only: true to only check the runtime allocated resources bitmap,
+ *		  false to check both runtime and statically allocated resource
+ *		  bitmaps.
+ * @or_stat: returns result of OR all the modules broadcast resources status
+ * @return: 0 for success, negative value for failure
+ */
+static int aie_part_rscmgr_get_or_bc_stat(struct aie_partition *apart,
+					  u32 num_rscs, struct aie_rsc *rscs,
+					  bool runtime_only,
+					  unsigned long *or_stat)
+{
+	u32 i;
+
+	*or_stat = 0;
+	for (i = 0; i < num_rscs; i++) {
+		struct aie_location l;
+		struct aie_rsc_stat *rstat;
+		int mod_num_rscs, start_bit;
+
+		l.col = apart->range.start.col + rscs[i].loc.col;
+		l.row = rscs[i].loc.row;
+		rstat = aie_part_get_rsc_bitmaps(apart, l, rscs[i].mod,
+						 AIE_RSCTYPE_BROADCAST);
+		start_bit = aie_part_get_rsc_startbit(apart, l, rscs[i].mod,
+						      AIE_RSCTYPE_BROADCAST);
+		if (!rstat || start_bit < 0) {
+			dev_err(&apart->dev,
+				"failed to get broadcast bitmap for[%u]:tile(%u,%u), mod=%u.\n",
+				i, rscs[i].loc.col, rscs[i].loc.row,
+				rscs[i].mod);
+			return -EINVAL;
+		}
+		mod_num_rscs = aie_part_get_mod_num_rscs(apart, l, rscs[i].mod,
+							 AIE_RSCTYPE_BROADCAST);
+		*or_stat |= aie_resource_or_get_valueul(&rstat->rbits,
+							start_bit,
+							mod_num_rscs);
+		if (!runtime_only)
+			*or_stat |= aie_resource_or_get_valueul(&rstat->sbits,
+								start_bit,
+								mod_num_rscs);
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_get_common_bc() - get common broadcast id of specified
+ *				     modules in the specified resources array.
+ *
+ * @apart: AI engine partition
+ * @num_rscs: number of broadcast resources, every module has one broadcast
+ *	      resource
+ * @rscs: array of broadcast resources, each element contains the tile
+ *	  location and module information of the broadcast channel
+ * @return: common broadcast channel id for success, negative value for failure
+ *
+ * This function checks both runtime and static allocated resources bitmap.
+ */
+static int aie_part_rscmgr_get_common_bc(struct aie_partition *apart,
+					 u32 num_rscs, struct aie_rsc *rscs)
+{
+	unsigned long or_stat, b;
+	int ret;
+	struct aie_location l;
+	int mod_num_rscs;
+
+	l.col = apart->range.start.col + (u32)rscs[0].loc.row;
+	l.row = (u32)rscs[0].loc.row;
+
+	ret = aie_part_rscmgr_get_or_bc_stat(apart, num_rscs, rscs, false,
+					     &or_stat);
+	if (ret)
+		return ret;
+
+	mod_num_rscs = aie_part_get_mod_num_rscs(apart, l, rscs[0].mod,
+						 AIE_RSCTYPE_BROADCAST);
+	b = bitmap_find_next_zero_area(&or_stat, mod_num_rscs, 0, 1, 0);
+	if (b >= mod_num_rscs)
+		return -EINVAL;
+
+	return (int)b;
+}
+
+/**
+ * aie_part_rscmgr_check_common_bc() - validate the specified common broadcast
+ *				       id in the specified modules in the
+ *				       specified resources array.
+ *
+ * @apart: AI engine partition
+ * @bc: broadcast channel id to check
+ * @num_rscs: number of broadcast resources, every module has one broadcast
+ *	      resource
+ * @rscs: array of broadcast resources, each element contains the tile
+ *	  location and module information of the broadcast channel
+ * @return: 0 if the specified broadcast channel id is available for all the
+ *	    specified modules, negative value for failure
+ *
+ * This function only checks runtime allocated resources bitmap.
+ */
+static int aie_part_rscmgr_check_common_bc(struct aie_partition *apart,
+					   u32 bc, u32 num_rscs,
+					   struct aie_rsc *rscs)
+{
+	unsigned long or_stat;
+	int ret;
+	struct aie_location l;
+	int mod_num_rscs;
+
+	l.col = apart->range.start.col + (u32)rscs[0].loc.row;
+	l.row = (u32)rscs[0].loc.row;
+
+	mod_num_rscs = aie_part_get_mod_num_rscs(apart, l, rscs[0].mod,
+						 AIE_RSCTYPE_BROADCAST);
+	if (bc > mod_num_rscs) {
+		dev_err(&apart->dev,
+			"invalid specified broadcast id %u, max is %u.\n",
+			bc, mod_num_rscs);
+		return -EINVAL;
+	}
+
+	ret = aie_part_rscmgr_get_or_bc_stat(apart, num_rscs, rscs, true,
+					     &or_stat);
+	if (ret)
+		return ret;
+
+	if (test_bit(bc, &or_stat)) {
+		dev_err(&apart->dev,
+			"specified broadcast id %u is occupied.\n", bc);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_check_rscs_modules() - validate the modules of the array of
+ *					input resources
+ *
+ * @apart: AI engine partition
+ * @num_rscs: number of resources
+ * @rscs: array of resources, each element contains the tile
+ *	  location and module information of the resource
+ * @return: 0 if the modules of all the resources are valid, negative value
+ *	    for failure
+ *
+ * This function validate the modules and the tiles of the resources, and
+ * check if resource module is gated.
+ */
+static int aie_part_rscmgr_check_rscs_modules(struct aie_partition *apart,
+					      u32 num_rscs,
+					      struct aie_rsc *rscs)
+{
+	struct aie_device *adev = apart->adev;
+	u32 i;
+
+	for (i = 0; i < num_rscs; i++) {
+		struct aie_location l;
+
+		l.col = rscs[i].loc.col;
+		l.row = rscs[i].loc.row;
+		/* validate tile location */
+		if (aie_validate_location(apart, l)) {
+			dev_err(&apart->dev,
+				"failed resource check tile(%u,%u) invalid.\n",
+					rscs[i].loc.col, rscs[i].loc.row);
+			return -EINVAL;
+		}
+
+		l.col += apart->range.start.col;
+		/* validate module */
+		if (aie_dev_get_mod_id(adev, adev->ops->get_tile_type(adev, &l),
+				       rscs[i].mod) < 0) {
+			dev_err(&apart->dev,
+				"failed resource check, tile(%u,%u) mod %u invalid.\n",
+					rscs[i].loc.col, rscs[i].loc.row,
+					rscs[i].mod);
+			return -EINVAL;
+		}
+
+		/* check if the resource module is gated */
+		if (!aie_part_check_clk_enable_loc(apart, &l)) {
+			dev_err(&apart->dev,
+				"failed resource check, tile(%u,%u) mod=%u is gated.\n",
+				rscs[i].loc.col, rscs[i].loc.row,
+				rscs[i].mod);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_set_tile_broadcast() - set broadcast channel in use
+ *					  of a module of a tile
+ *
+ * @apart: AI engine partition
+ * @loc: tile location
+ * @mod: module
+ * @id: broadcast channel id
+ * @return: 0 for success, negative value for failure
+ *
+ * This function will set the bit of the specified broadcast channel in the
+ * runtime broadcast bitmap of the specified module of the specified tile.
+ */
+int aie_part_rscmgr_set_tile_broadcast(struct aie_partition *apart,
+				       struct aie_location loc,
+				       enum aie_module_type mod, uint32_t id)
+{
+	struct aie_rsc_stat *rstat;
+	int start_bit;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	rstat = aie_part_get_rsc_bitmaps(apart, loc, mod,
+					 AIE_RSCTYPE_BROADCAST);
+	/* bitmap pointer cannot be NULL. */
+	if (WARN_ON(!rstat || !rstat->rbits.bitmap))
+		return -EFAULT;
+
+	start_bit = aie_part_get_rsc_startbit(apart, loc, mod,
+					      AIE_RSCTYPE_BROADCAST);
+	aie_resource_set(&rstat->rbits, start_bit + id, 1);
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_get_broadcast() - get common broadcast channel of
+ *				     the specified modules or the whole
+ *				     partition.
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource free arguments
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function get a common broadcast channel for the specified set
+ * of AI engine modules in the resources array. If the any of the input set of
+ * tiles is gated, it will return failure. This ioctl will not check the
+ * connection of the input modules set.
+ * The driver will fill in the resource ID with the assigned broadcast channel
+ * ID of the resources array.
+ * If the XAIE_BROADCAST_ALL is set in the request flag, it will get the
+ * broadcast channel for all the ungated tiles of the partition.
+ * If a particular broadcast channel id is specified in the request, if will
+ * check if the channel is available for the specified modules, or the whole
+ * partition depends on if XAIE_BROADCAST_ALL is set.
+ */
+long aie_part_rscmgr_get_broadcast(struct aie_partition *apart,
+				   void __user *user_args)
+{
+	struct aie_rsc_bc_req args;
+	struct aie_rsc *rscs;
+	u32 i;
+	long ret;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	rscs = kmalloc_array(args.num_rscs, sizeof(*rscs), GFP_KERNEL);
+	if (!rscs)
+		return -ENOMEM;
+
+	if (!(args.flag & XAIE_BROADCAST_ALL)) {
+		if (copy_from_user(rscs, (void __user *)args.rscs,
+				   sizeof(*rscs) * args.num_rscs)) {
+			kfree(rscs);
+			return -EFAULT;
+		}
+	}
+
+	ret = mutex_lock_interruptible(&apart->mlock);
+	if (ret) {
+		kfree(rscs);
+		return ret;
+	}
+
+	if (args.flag & XAIE_BROADCAST_ALL)
+		/*
+		 * It is to broadcast to the whole partition.
+		 * Get all the ungated modules.
+		 */
+		ret = aie_part_rscmgr_get_ungated_bc_mods(apart, args.num_rscs,
+							  &args.num_rscs,
+							  rscs);
+	else
+		/*
+		 * validate tiles and modules, and check if there are modules
+		 * gated
+		 */
+		ret = aie_part_rscmgr_check_rscs_modules(apart, args.num_rscs,
+							 rscs);
+	if (ret)
+		goto error;
+
+	/* find the common broadcast signal among the specified modules */
+	if (args.id == XAIE_BROADCAST_ID_ANY) {
+		ret = aie_part_rscmgr_get_common_bc(apart, args.num_rscs, rscs);
+		if (ret >= 0) {
+			args.id = (u32)ret;
+			ret = 0;
+		} else {
+			dev_warn(&apart->dev, "no available broadcast channel.\n");
+		}
+	} else {
+		ret = aie_part_rscmgr_check_common_bc(apart, args.id,
+						      args.num_rscs,
+						      rscs);
+	}
+	if (ret)
+		goto error;
+
+	/* set the broadcast channel resource runtime status bit */
+	for (i = 0; i < args.num_rscs; i++) {
+		struct aie_location l;
+
+		l.col = apart->range.start.col + rscs[i].loc.col;
+		l.row = rscs[i].loc.row;
+		ret = aie_part_rscmgr_set_tile_broadcast(apart, l, rscs[i].mod,
+							 args.id);
+		if (ret)
+			goto error;
+
+		rscs[i].id = args.id;
+	}
+
+	mutex_unlock(&apart->mlock);
+
+	if (copy_to_user((void __user *)args.rscs, rscs,
+			 sizeof(*rscs) * args.num_rscs)) {
+		kfree(rscs);
+		return -EFAULT;
+	}
+
+	/*
+	 * If it is required to broadcast to whole partition, it needs to
+	 * return the actual number of broadcast resources as some tiles
+	 * can be gated
+	 */
+	if (args.flag & XAIE_BROADCAST_ALL) {
+		struct aie_rsc_bc_req __user *uargs = user_args;
+
+		if (copy_to_user((void __user *)&uargs->num_rscs,
+				 &args.num_rscs, sizeof(args.num_rscs))) {
+			kfree(rscs);
+			return -EFAULT;
+		}
+	}
+
+	kfree(rscs);
+	return 0;
+error:
+	mutex_unlock(&apart->mlock);
+	kfree(rscs);
+	return ret;
+}
+
+/**
+ * aie_part_rscmgr_set_static() - sets statically allocated resources bitmaps
+ *
+ * @apart: AI engine partition
+ * @meta: meta data which contains the statically allocated resources bitmaps
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function takes the static bitmap information from meta data and fill
+ * in the static bitmap.
+ */
+int aie_part_rscmgr_set_static(struct aie_partition *apart, void *meta)
+{
+	struct aie_rsc_meta_header *header = meta;
+	struct aie_rsc_bitmap *bitmap;
+	u64 i, num_bitmaps, offset;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return 0;
+	}
+
+	if (!header) {
+		dev_err(&apart->dev,
+			"failed to get static resources, meta data is NULL.\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * For now, the stat field of the header only contains the number of
+	 * bitmaps.
+	 */
+	num_bitmaps = header->stat;
+	offset = header->bitmap_off;
+	if (!num_bitmaps || offset < sizeof(*header)) {
+		dev_err(&apart->dev,
+			"failed to get static resources, invalid header.\n");
+		return -EINVAL;
+	}
+
+	bitmap = (struct aie_rsc_bitmap *)(meta + offset);
+	for (i = 0; i < num_bitmaps; i++) {
+		struct aie_rsc_stat *rstat;
+		const struct aie_mod_rsc_attr *mrattr;
+		u64 header = bitmap->header;
+		u32 lrlen, rlen, ttype, mtype, rtype, total;
+
+		ttype = AIE_RSC_BITMAP_HEAD_VAL(TILETYPE, header);
+		mtype = AIE_RSC_BITMAP_HEAD_VAL(MODTYPE, header);
+		rtype = AIE_RSC_BITMAP_HEAD_VAL(RSCTYPE, header);
+		rlen = AIE_RSC_BITMAP_HEAD_VAL(LENU64, header);
+
+		if (!rlen) {
+			dev_err(&apart->dev,
+				"invalid static bitmap[%llu], length is 0.\n",
+				i);
+			return -EINVAL;
+		}
+
+		mrattr = aie_dev_get_mod_rsc_attr(apart->adev, ttype, mtype,
+						  rtype);
+		if (!mrattr) {
+			dev_err(&apart->dev,
+				"invalid static bitmap[%llu], invalid tile(%u)/module(%u)/rsce(%u) types combination.\n",
+				i, ttype, mtype, rtype);
+			return -EINVAL;
+		}
+
+		total = mrattr->num_rscs * apart->range.size.col *
+			aie_part_get_tile_rows(apart, ttype);
+		lrlen = BITS_TO_LONGS(total);
+		if (rlen != lrlen) {
+			dev_err(&apart->dev,
+				"invalid static bitmap[%llu], tile(%u)/module(%u)/rscs(%u), expect len(%u), actual(%u).\n",
+				i, ttype, mtype, rtype, lrlen, rlen);
+			return -EINVAL;
+		}
+
+		rstat = aie_part_get_ttype_rsc_bitmaps(apart, ttype, mtype,
+						       rtype);
+		/* if bitmap length is not 0, bitmap pointer cannot be NULL. */
+		if (WARN_ON(!rstat || !rstat->sbits.bitmap))
+			return -EFAULT;
+
+		/* copy the bitmap from meta data */
+		bitmap_copy(rstat->sbits.bitmap,
+			    (unsigned long *)bitmap->bitmap, total);
+
+		bitmap = (struct aie_rsc_bitmap *)((void *)bitmap +
+						   sizeof(header) +
+						   rlen * sizeof(u64));
+	}
+
+	return 0;
+}
+
+/**
+ * aie_part_rscmgr_check_static() - check the number of static resources
+ *
+ * @rstat: resource statistics structure which contains bitmaps of a resource
+ *	   type of a module type of a tile type.
+ * @sbit: start bit of the resource bitmap of a tile of a module
+ * @total: number of total resources bits to check
+ *
+ * @return: number of static resources
+ *
+ * This function returns the number of static resources of a resource
+ * bitmap.
+ */
+static int aie_part_rscmgr_check_static(struct aie_rsc_stat *rstat,
+					u32 sbit, u32 total)
+{
+	u32 i;
+	int num_static = 0;
+
+	for (i = sbit; i < sbit + total; i++) {
+		if (aie_resource_testbit(&rstat->sbits, i))
+			num_static++;
+	}
+
+	return num_static;
+}
+
+/**
+ * aie_part_rscmgr_check_avail() - check the number of available resources
+ *
+ * @rstat: resource statistics structure which contains bitmaps of a resource
+ *	   type of a module type of a tile type.
+ * @sbit: start bit of the resource bitmap of a tile of a module
+ * @total: number of total resources bits to check
+ *
+ * @return: number of available resources for success, negative value for
+ *	    failure
+ *
+ * This function returns the number of available resources of a resource
+ * bitmap.
+ */
+static int aie_part_rscmgr_check_avail(struct aie_rsc_stat *rstat,
+				       u32 sbit, u32 total)
+{
+	return aie_resource_check_common_avail(&rstat->rbits,
+					       &rstat->sbits,
+					       sbit, total);
+}
+
+/**
+ * aie_part_rscmgr_get_statistics() - get resource statistics based on user
+ *				      request
+ *
+ * @apart: AI engine partition
+ * @user_args: user resource statistics request. it contains the number of
+ *	       resource statistics wants to get followed by the statistics
+ *	       array and the statistics type to specify if it is for static
+ *	       allocated resources or available resources. Each statistics
+ *	       element contains the tile location, module type and the resource
+ *	       type.
+ *
+ * @return: 0 for success, negative value for failure
+ *
+ * This function returns the resource statistics based on the user request.
+ * If user requests for available resource statistics, it returns the number
+ * of available resources of each resource statistics entry. If user requests
+ * for static resources statistics, it returns the number of static resources
+ * of each resource statistics entry.
+ */
+long aie_part_rscmgr_get_statistics(struct aie_partition *apart,
+				    void __user *user_args)
+{
+	struct aie_rsc_user_stat_array args;
+	struct aie_rsc_user_stat __user *ustat_ptr;
+	u32 i;
+
+	/*
+	 * TODO: resource manager is not supported for AIEML device and the
+	 * users are not expected to call any function as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_warn(&apart->dev, "rsc mgr not supported for device.\n");
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&args, user_args, sizeof(args)))
+		return -EFAULT;
+
+	if (args.stats_type >= AIE_RSC_STAT_TYPE_MAX) {
+		dev_err(&apart->dev,
+			"get rsc statistics failed, invalid rsc stat type %u.\n",
+			args.stats_type);
+		return -EINVAL;
+	}
+
+	ustat_ptr = (struct aie_rsc_user_stat __user *)args.stats;
+	for (i = 0; i < args.num_stats; i++) {
+		struct aie_rsc_user_stat ustat;
+		struct aie_rsc_stat *rstat;
+		struct aie_location rloc, loc;
+		long ret;
+		int max_rscs, start_bit;
+
+		if (copy_from_user(&ustat, (void __user *)ustat_ptr,
+				   sizeof(ustat)))
+			return -EFAULT;
+
+		/* convert user tile loc to kernel tile loc format */
+		rloc.col = (u32)(ustat.loc.col & 0xFF);
+		rloc.row = (u32)(ustat.loc.row & 0xFF);
+		ret = aie_part_adjust_loc(apart, rloc, &loc);
+		if (ret < 0)
+			return ret;
+
+		if (ustat.type > AIE_RSCTYPE_MAX) {
+			dev_err(&apart->dev,
+				"get rsc statistics failed, invalid resource type %d.\n",
+				ustat.type);
+			return -EINVAL;
+		}
+
+		rstat = aie_part_get_rsc_bitmaps(apart, loc, ustat.mod,
+						 ustat.type);
+		start_bit = aie_part_get_rsc_startbit(apart, loc, ustat.mod,
+						      ustat.type);
+		if (!rstat || start_bit < 0) {
+			dev_err(&apart->dev,
+				"get rsc statistics failed, invalid resource(%u,%u),mod:%u,rsc:%u.\n",
+				loc.col, loc.row, ustat.mod, ustat.type);
+			return -EINVAL;
+		}
+
+		max_rscs = aie_part_get_mod_num_rscs(apart, loc, ustat.mod,
+						     ustat.type);
+		ret = mutex_lock_interruptible(&apart->mlock);
+		if (ret)
+			return ret;
+
+		if (args.stats_type == AIE_RSC_STAT_TYPE_STATIC)
+			ustat.num_rscs = aie_part_rscmgr_check_static(rstat,
+								      start_bit,
+								      max_rscs);
+		else
+			ustat.num_rscs = aie_part_rscmgr_check_avail(rstat,
+								     start_bit,
+								     max_rscs);
+
+		mutex_unlock(&apart->mlock);
+		if (WARN_ON(ustat.num_rscs < 0))
+			return -EFAULT;
+
+		/* copy the information back to userspace */
+		if (copy_to_user((void __user *)ustat_ptr, &ustat,
+				 sizeof(ustat)))
+			return -EFAULT;
+
+		ustat_ptr++;
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-clock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-clock.c
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver sysfs for clock.
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+
+/**
+ * aie_part_show_current_freq() - exports AI engine partition current frequency
+ *
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_show_current_freq(struct device *dev,
+				   struct device_attribute *attr, char *buffer)
+{
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	int ret = 0;
+	u64 freq;
+
+	if (mutex_lock_interruptible(&apart->mlock))
+		return ret;
+
+	ret = aie_part_get_freq(apart, &freq);
+	if (ret) {
+		dev_err(dev, "Failed to get partition frequency.\n");
+		mutex_unlock(&apart->mlock);
+		return ret;
+	}
+
+	mutex_unlock(&apart->mlock);
+
+	return scnprintf(buffer, PAGE_SIZE, "%llu\n", freq);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-core.c
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver.
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+
+#define AIE_CORE_STS_ENABLE_MASK	0x3U
+
+/**
+ * aie_get_core_pc() - reads the AI engine core program counter value.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine core.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_core_pc(struct aie_partition *apart,
+			   struct aie_location *loc)
+{
+	u32 regoff;
+
+	regoff = aie_cal_regoff(apart->adev, *loc,
+				apart->adev->core_pc->regoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_core_lr() - reads the AI engine core link register value.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine core.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_core_lr(struct aie_partition *apart,
+			   struct aie_location *loc)
+{
+	u32 regoff;
+
+	regoff = aie_cal_regoff(apart->adev, *loc,
+				apart->adev->core_lr->regoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_core_sp() - reads the AI engine core stack pointer value.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine core.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_core_sp(struct aie_partition *apart,
+			   struct aie_location *loc)
+{
+	u32 regoff;
+
+	regoff = aie_cal_regoff(apart->adev, *loc,
+				apart->adev->core_sp->regoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_sysfs_get_core_status() - returns the status of core in string format
+ *				 with each status value separated by a '|'
+ *				 symbol.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine core.
+ * @buffer: location to return core status string.
+ * @size: total size of buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_sysfs_get_core_status(struct aie_partition *apart,
+				  struct aie_location *loc, char *buffer,
+				  ssize_t size)
+{
+	ssize_t len = 0;
+	u32 ttype, n;
+	unsigned long status;
+	bool is_delimit_req = false;
+	char **str = apart->adev->core_status_str;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		return len;
+
+	if (!aie_part_check_clk_enable_loc(apart, loc)) {
+		len += scnprintf(buffer, max(0L, size), "clock_gated");
+		return len;
+	}
+
+	/*
+	 * core is in disabled state when neither the enable nor reset bit is
+	 * high
+	 */
+	status = apart->adev->ops->get_core_status(apart, loc);
+	if (!(status & AIE_CORE_STS_ENABLE_MASK)) {
+		len += scnprintf(&buffer[len], max(0L, size - len), "disabled");
+		is_delimit_req = true;
+	}
+
+	for_each_set_bit(n, &status, 32) {
+		if (is_delimit_req) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 DELIMITER_LEVEL0);
+		}
+		len += scnprintf(&buffer[len], max(0L, size - len), str[n]);
+		is_delimit_req = true;
+	}
+
+	return len;
+}
+
+/**
+ * aie_tile_show_core() - exports AI engine core status, value of program
+ *			  counter, stack pointer, and link register to a tile
+ *			  level sysfs node.
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_tile_show_core(struct device *dev, struct device_attribute *attr,
+			   char *buffer)
+{
+	struct aie_tile *atile = container_of(dev, struct aie_tile, dev);
+	struct aie_partition *apart = atile->apart;
+	ssize_t len = 0, size = PAGE_SIZE;
+	u32 pc = 0, lr = 0, sp = 0;
+	char sts_buf[AIE_SYSFS_CORE_STS_SIZE];
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	if (!aie_part_check_clk_enable_loc(apart, &atile->loc)) {
+		scnprintf(sts_buf, AIE_SYSFS_CORE_STS_SIZE, "clock_gated");
+		goto out;
+	}
+
+	aie_sysfs_get_core_status(apart, &atile->loc, sts_buf,
+				  AIE_SYSFS_CORE_STS_SIZE);
+	pc = aie_get_core_pc(apart, &atile->loc);
+	lr = aie_get_core_lr(apart, &atile->loc);
+	sp = aie_get_core_sp(apart, &atile->loc);
+
+out:
+	mutex_unlock(&apart->mlock);
+
+	len += scnprintf(&buffer[len], max(0L, size - len), "status: %s\n",
+			 sts_buf);
+	len += scnprintf(&buffer[len], max(0L, size - len), "pc: %#.8x\n", pc);
+	len += scnprintf(&buffer[len], max(0L, size - len), "lr: %#.8x\n", lr);
+	len += scnprintf(&buffer[len], max(0L, size - len), "sp: %#.8x\n", sp);
+	return len;
+}
+
+/**
+ * aie_part_read_cb_core() - exports status of all cores within a given
+ *			     partition to partition level node.
+ * @kobj: kobject used to create sysfs node.
+ * @buffer: export buffer.
+ * @size: length of export buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_read_cb_core(struct kobject *kobj, char *buffer, ssize_t size)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_tile *atile = apart->atiles;
+	ssize_t len = 0;
+	u32 index;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++) {
+		u32 ttype = apart->adev->ops->get_tile_type(apart->adev,
+							    &atile->loc);
+
+		if (ttype != AIE_TILE_TYPE_TILE)
+			continue;
+
+		len += scnprintf(&buffer[len], max(0L, size - len), "%d_%d: ",
+				 atile->loc.col, atile->loc.row);
+		len += aie_sysfs_get_core_status(apart, &atile->loc,
+						 &buffer[len], size - len);
+		len += scnprintf(&buffer[len], max(0L, size - len), "\n");
+	}
+
+	mutex_unlock(&apart->mlock);
+	return len;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-dma.c
@@ -0,0 +1,466 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver.
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+
+/**
+ * aie_get_dma_s2mm_status() - reads the DMA stream to memory map status.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_dma_s2mm_status(struct aie_partition *apart,
+				   struct aie_location *loc)
+{
+	u32 stsoff, regoff, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		stsoff = apart->adev->shim_dma->s2mm_sts_regoff;
+	else
+		stsoff = apart->adev->tile_dma->s2mm_sts_regoff;
+
+	regoff = aie_cal_regoff(apart->adev, *loc, stsoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_dma_mm2s_status() - reads the DMA memory map to stream status.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_dma_mm2s_status(struct aie_partition *apart,
+				   struct aie_location *loc)
+{
+	u32 stsoff, regoff, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		stsoff = apart->adev->shim_dma->mm2s_sts_regoff;
+	else
+		stsoff = apart->adev->tile_dma->mm2s_sts_regoff;
+
+	regoff = aie_cal_regoff(apart->adev, *loc, stsoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_chan_status() - reads the DMA channel status.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @status: status value of DMA.
+ * @chanid: DMA channel ID.
+ * @return: 8-bit status value.
+ */
+static u8 aie_get_chan_status(struct aie_partition *apart,
+			      struct aie_location *loc, u32 status, u8 chanid)
+{
+	const struct aie_single_reg_field *sts, *stall;
+	u32 mask, chan_shift, shift, value, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE) {
+		sts = &apart->adev->shim_dma->sts;
+		stall = &apart->adev->shim_dma->stall;
+	} else {
+		sts = &apart->adev->tile_dma->sts;
+		stall = &apart->adev->tile_dma->stall;
+	}
+
+	chan_shift = sts->regoff;
+	mask = sts->mask << (chan_shift * chanid);
+	shift = ffs(mask) - 1;
+	value = (status & mask) >> shift;
+
+	chan_shift = stall->regoff;
+	mask = stall->mask << (chan_shift * chanid);
+	shift = ffs(mask) - 1;
+	value |= (status & mask) >> shift;
+	return value;
+}
+
+/**
+ * aie_get_queue_size() - reads the DMA queue size.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @status: status value of DMA.
+ * @chanid: DMA channel ID.
+ * @return: 8-bit value.
+ */
+static u8 aie_get_queue_size(struct aie_partition *apart,
+			     struct aie_location *loc, u32 status, u8 chanid)
+{
+	const struct aie_single_reg_field *qsize;
+	u32 mask, chan_shift, shift, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		qsize = &apart->adev->shim_dma->qsize;
+	else
+		qsize = &apart->adev->tile_dma->qsize;
+
+	chan_shift = qsize->regoff;
+	mask = qsize->mask << (chan_shift * chanid);
+	shift = ffs(mask) - 1;
+	return (status & mask) >> shift;
+}
+
+/**
+ * aie_get_queue_status() - reads the DMA queue status.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @status: status value of DMA.
+ * @chanid: DMA channel ID.
+ * @return: 8-bit status value.
+ */
+static u8 aie_get_queue_status(struct aie_partition *apart,
+			       struct aie_location *loc, u32 status, u8 chanid)
+{
+	const struct aie_single_reg_field *qsts;
+	u32 mask, chan_shift, shift, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		qsts = &apart->adev->shim_dma->qsts;
+	else
+		qsts = &apart->adev->tile_dma->qsts;
+
+	chan_shift = qsts->regoff;
+	mask = qsts->mask << (chan_shift * chanid);
+	shift = ffs(mask) - 1;
+	return (status & mask) >> shift;
+}
+
+/**
+ * aie_get_current_bd() - reads the current buffer descriptor being processed
+ *			  by DMA channel.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @status: status value of DMA.
+ * @chanid: DMA channel ID.
+ * @return: 8-bit buffer descriptor value.
+ */
+static u8 aie_get_current_bd(struct aie_partition *apart,
+			     struct aie_location *loc, u32 status, u8 chanid)
+{
+	const struct aie_single_reg_field *curbd;
+	u32 mask, chan_shift, shift, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		curbd = &apart->adev->shim_dma->curbd;
+	else
+		curbd = &apart->adev->tile_dma->curbd;
+
+	chan_shift = curbd->regoff;
+	mask = curbd->mask << (chan_shift * chanid);
+	shift = ffs(mask) - 1;
+	return (status & mask) >> shift;
+}
+
+/**
+ * aie_get_fifo_status() - reads the current value of DMA FIFO counters.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @return: concatenated value of counters for AIE tiles and 0 for shim tiles.
+ */
+static u32 aie_get_fifo_status(struct aie_partition *apart,
+			       struct aie_location *loc)
+{
+	u32 fifo_off, regoff, ttype;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		return 0U;
+
+	fifo_off = apart->adev->tile_dma->fifo_cnt_regoff;
+
+	regoff = aie_cal_regoff(apart->adev, *loc, fifo_off);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_fifo_count() - returns the value of a DMA FIFO counter from its
+ *			  concatenated register value.
+ * @apart: AI engine partition.
+ * @status: register value of DMA FIFO counter.
+ * @counterid: counter ID.
+ * @return: DMA FIFO count.
+ */
+static u32 aie_get_fifo_count(struct aie_partition *apart, u32 status,
+			      u8 counterid)
+{
+	const struct aie_single_reg_field *fifo;
+
+	fifo = &apart->adev->tile_dma->fifo_cnt;
+
+	status >>= (fifo->regoff * counterid);
+	return (status & fifo->mask);
+}
+
+/**
+ * aie_sysfs_get_dma_status() - returns the status of DMA in string format with
+ *				MM2S and S2MM type channel separated by a ','
+ *				symbol. Channels with a given type are
+ *				separated by a '|' symbol.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @buffer: location to return DMA status string.
+ * @size: total size of buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_sysfs_get_dma_status(struct aie_partition *apart,
+				 struct aie_location *loc, char *buffer,
+				 ssize_t size)
+{
+	u32 i, ttype, num_s2mm_chan, num_mm2s_chan;
+	ssize_t len = 0;
+	unsigned long status;
+	bool is_delimit_req = false;
+	char **str = apart->adev->dma_status_str;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype == AIE_TILE_TYPE_SHIMPL)
+		return len;
+
+	if (!aie_part_check_clk_enable_loc(apart, loc)) {
+		len += scnprintf(buffer, max(0L, size - len),
+				 "mm2s: clock_gated%ss2mm: clock_gated",
+				 DELIMITER_LEVEL1);
+		return len;
+	}
+
+	if (ttype != AIE_TILE_TYPE_TILE) {
+		num_mm2s_chan = apart->adev->shim_dma->num_mm2s_chan;
+		num_s2mm_chan = apart->adev->shim_dma->num_s2mm_chan;
+	} else {
+		num_mm2s_chan = apart->adev->tile_dma->num_mm2s_chan;
+		num_s2mm_chan = apart->adev->tile_dma->num_s2mm_chan;
+	}
+
+	/* MM2S */
+	len += scnprintf(&buffer[len], max(0L, size - len), "mm2s: ");
+	status = aie_get_dma_mm2s_status(apart, loc);
+	for (i = 0; i < num_mm2s_chan; i++) {
+		u32 value = aie_get_chan_status(apart, loc, status, i);
+
+		if (is_delimit_req) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 DELIMITER_LEVEL0);
+		}
+		len += scnprintf(&buffer[len], max(0L, size - len), str[value]);
+		is_delimit_req = true;
+	}
+
+	/* S2MM */
+	is_delimit_req = false;
+	len += scnprintf(&buffer[len], max(0L, size - len), "%ss2mm: ",
+			 DELIMITER_LEVEL1);
+	status = aie_get_dma_s2mm_status(apart, loc);
+	for (i = 0; i < num_s2mm_chan; i++) {
+		u32 value = aie_get_chan_status(apart, loc, status, i);
+
+		if (is_delimit_req) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 DELIMITER_LEVEL0);
+		}
+		len += scnprintf(&buffer[len], max(0L, size - len), str[value]);
+		is_delimit_req = true;
+	}
+	return len;
+}
+
+/**
+ * aie_tile_show_dma() - exports AI engine DMA channel status, queue size,
+ *			 queue status, and current buffer descriptor ID being
+ *			 processed by DMA channel to a tile level sysfs node.
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_tile_show_dma(struct device *dev, struct device_attribute *attr,
+			  char *buffer)
+{
+	struct aie_tile *atile = container_of(dev, struct aie_tile, dev);
+	struct aie_partition *apart = atile->apart;
+	u32 ttype, i, num_s2mm_chan, num_mm2s_chan, fifo, fifo0_len, fifo1_len;
+	unsigned long status;
+	bool is_delimit_req = false;
+	ssize_t len = 0, size = PAGE_SIZE, l0 = 0, l1 = 0, l2 = 0, l3 = 0;
+	char **qsts_str = apart->adev->queue_status_str;
+	char ch_buf[AIE_SYSFS_CHAN_STS_SIZE],
+	     qsz_mm2s_buf[AIE_SYSFS_QUEUE_SIZE_SIZE],
+	     qsz_s2mm_buf[AIE_SYSFS_QUEUE_SIZE_SIZE],
+	     qsts_mm2s_buf[AIE_SYSFS_QUEUE_STS_SIZE],
+	     qsts_s2mm_buf[AIE_SYSFS_QUEUE_STS_SIZE],
+	     bd_mm2s_buf[AIE_SYSFS_BD_SIZE],
+	     bd_s2mm_buf[AIE_SYSFS_BD_SIZE],
+	     fifo_len_buf[AIE_SYSFS_FIFO_LEN_SIZE];
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	if (!aie_part_check_clk_enable_loc(apart, &atile->loc)) {
+		scnprintf(ch_buf, AIE_SYSFS_CHAN_STS_SIZE,
+			  "mm2s: clock_gated%ss2mm: clock_gated",
+			  DELIMITER_LEVEL1);
+		scnprintf(qsz_mm2s_buf, AIE_SYSFS_QUEUE_SIZE_SIZE,
+			  "clock_gated");
+		scnprintf(qsts_mm2s_buf, AIE_SYSFS_QUEUE_STS_SIZE,
+			  "clock_gated");
+		scnprintf(bd_mm2s_buf, AIE_SYSFS_BD_SIZE, "clock_gated");
+		scnprintf(qsz_s2mm_buf, AIE_SYSFS_QUEUE_SIZE_SIZE,
+			  "clock_gated");
+		scnprintf(qsts_s2mm_buf, AIE_SYSFS_QUEUE_STS_SIZE,
+			  "clock_gated");
+		scnprintf(bd_s2mm_buf, AIE_SYSFS_BD_SIZE, "clock_gated");
+		scnprintf(fifo_len_buf, AIE_SYSFS_BD_SIZE, "clock_gated");
+		goto print;
+	}
+
+	aie_sysfs_get_dma_status(apart, &atile->loc, ch_buf,
+				 AIE_SYSFS_CHAN_STS_SIZE);
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, &atile->loc);
+	if (ttype != AIE_TILE_TYPE_TILE) {
+		num_mm2s_chan = apart->adev->shim_dma->num_mm2s_chan;
+		num_s2mm_chan = apart->adev->shim_dma->num_s2mm_chan;
+	} else {
+		num_mm2s_chan = apart->adev->tile_dma->num_mm2s_chan;
+		num_s2mm_chan = apart->adev->tile_dma->num_s2mm_chan;
+	}
+
+	/* MM2S */
+	status = aie_get_dma_mm2s_status(apart, &atile->loc);
+	for (i = 0; i < num_mm2s_chan; i++) {
+		u8 qsize = aie_get_queue_size(apart, &atile->loc, status, i);
+		u8 qsts = aie_get_queue_status(apart, &atile->loc, status, i);
+		u8 curbd = aie_get_current_bd(apart, &atile->loc, status, i);
+
+		if (is_delimit_req) {
+			l0 += scnprintf(&qsz_mm2s_buf[l0],
+					max(0L, AIE_SYSFS_QUEUE_SIZE_SIZE - l0),
+					DELIMITER_LEVEL0);
+			l1 += scnprintf(&qsts_mm2s_buf[l1],
+					max(0L, AIE_SYSFS_QUEUE_STS_SIZE - l1),
+					DELIMITER_LEVEL0);
+			l2 += scnprintf(&bd_mm2s_buf[l2],
+					max(0L, AIE_SYSFS_BD_SIZE - l2),
+					DELIMITER_LEVEL0);
+		}
+		l0 += scnprintf(&qsz_mm2s_buf[l0],
+				max(0L, AIE_SYSFS_QUEUE_SIZE_SIZE - l0), "%d",
+				qsize);
+		l1 += scnprintf(&qsts_mm2s_buf[l1],
+				max(0L, AIE_SYSFS_QUEUE_STS_SIZE - l1),
+				qsts_str[qsts]);
+		l2 += scnprintf(&bd_mm2s_buf[l2],
+				max(0L, AIE_SYSFS_BD_SIZE - l2), "%d", curbd);
+		is_delimit_req = true;
+	}
+
+	/* S2MM */
+	is_delimit_req = false;
+	l0 = 0; l1 = 0; l2 = 0;
+	status = aie_get_dma_s2mm_status(apart, &atile->loc);
+	for (i = 0; i < num_s2mm_chan; i++) {
+		u8 qsize = aie_get_queue_size(apart, &atile->loc, status, i);
+		u8 qsts = aie_get_queue_status(apart, &atile->loc, status, i);
+		u8 curbd = aie_get_current_bd(apart, &atile->loc, status, i);
+
+		if (is_delimit_req) {
+			l0 += scnprintf(&qsz_s2mm_buf[l0],
+					max(0L, AIE_SYSFS_QUEUE_SIZE_SIZE - l0),
+					DELIMITER_LEVEL0);
+			l1 += scnprintf(&qsts_s2mm_buf[l1],
+					max(0L, AIE_SYSFS_QUEUE_STS_SIZE - l1),
+					DELIMITER_LEVEL0);
+			l2 += scnprintf(&bd_s2mm_buf[l2],
+					max(0L, AIE_SYSFS_BD_SIZE - l2),
+					DELIMITER_LEVEL0);
+		}
+		l0 += scnprintf(&qsz_s2mm_buf[l0],
+				max(0L, AIE_SYSFS_QUEUE_SIZE_SIZE - l0), "%d",
+				qsize);
+		l1 += scnprintf(&qsts_s2mm_buf[l1],
+				max(0L, AIE_SYSFS_QUEUE_STS_SIZE - l1),
+				qsts_str[qsts]);
+		l2 += scnprintf(&bd_s2mm_buf[l2],
+				max(0L, AIE_SYSFS_BD_SIZE - l2), "%d", curbd);
+		is_delimit_req = true;
+	}
+
+	fifo = aie_get_fifo_status(apart,  &atile->loc);
+	fifo0_len = aie_get_fifo_count(apart, fifo, 0);
+	fifo1_len = aie_get_fifo_count(apart, fifo, 1);
+
+	l3 += scnprintf(&fifo_len_buf[l3],
+			max(0L, AIE_SYSFS_QUEUE_SIZE_SIZE - l3), "%d%s%d",
+			fifo0_len, DELIMITER_LEVEL0, fifo1_len);
+
+print:
+	mutex_unlock(&apart->mlock);
+	len += scnprintf(&buffer[len], max(0L, size - len),
+			 "channel_status: %s\n", ch_buf);
+	len += scnprintf(&buffer[len], max(0L, size - len),
+			 "queue_size: mm2s: %s%ss2mm: %s\n", qsz_mm2s_buf,
+			 DELIMITER_LEVEL1, qsz_s2mm_buf);
+	len += scnprintf(&buffer[len], max(0L, size - len),
+			 "queue_status: mm2s: %s%ss2mm: %s\n", qsts_mm2s_buf,
+			 DELIMITER_LEVEL1, qsts_s2mm_buf);
+	len += scnprintf(&buffer[len], max(0L, size - len),
+			 "current_bd: mm2s: %s%ss2mm: %s\n", bd_mm2s_buf,
+			 DELIMITER_LEVEL1, bd_s2mm_buf);
+	len += scnprintf(&buffer[len], max(0L, size - len),
+			 "fifo_len: %s\n", fifo_len_buf);
+	return len;
+}
+
+/**
+ * aie_part_read_cb_dma() - exports status of all DMAs within a given
+ *			    partition to partition level node.
+ * @kobj: kobject used to create sysfs node.
+ * @buffer: export buffer.
+ * @size: length of export buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_read_cb_dma(struct kobject *kobj, char *buffer, ssize_t size)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_tile *atile = apart->atiles;
+	ssize_t len = 0;
+	u32 index;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++) {
+		u32 ttype = apart->adev->ops->get_tile_type(apart->adev,
+							    &atile->loc);
+
+		if (ttype == AIE_TILE_TYPE_SHIMPL)
+			continue;
+
+		len += scnprintf(&buffer[len], max(0L, size - len), "%d_%d: ",
+				 atile->loc.col, atile->loc.row);
+		len += aie_sysfs_get_dma_status(apart, &atile->loc,
+						&buffer[len], size - len);
+		len += scnprintf(&buffer[len], max(0L, size - len), "\n");
+	}
+
+	mutex_unlock(&apart->mlock);
+	return len;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-error.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-error.c
@@ -0,0 +1,352 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver.
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+#include "linux/xlnx-ai-engine.h"
+
+static char *aie_error_category_str[] = {
+	"saturation",
+	"floating_point",
+	"stream_switch",
+	"access",
+	"bus",
+	"instruction",
+	"ecc",
+	"lock",
+	"dma",
+	"memory_parity",
+};
+
+/**
+ * aie_get_errors_str() - returns errors in string format. Errors of the same
+ *			  category are separated by a '|' symbol with the error
+ *			  category sting as a label prefix.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine tile.
+ * @module: module type.
+ * @err_attr: error attribute for given module type.
+ * @buffer: location to return error string.
+ * @size: total size of buffer available.
+ * @return: length of string copied to buffer.
+ */
+static ssize_t aie_get_errors_str(struct aie_partition *apart,
+				  struct aie_location loc,
+				  enum aie_module_type module,
+				  const struct aie_error_attr *err_attr,
+				  char *buffer, ssize_t size)
+{
+	ssize_t len = 0;
+	u32 i, j;
+	char *mod;
+
+	if (module == AIE_CORE_MOD)
+		mod = "core";
+	else if (module == AIE_MEM_MOD)
+		mod = "memory";
+	else
+		mod = "pl";
+
+	for (i = 0; i < err_attr->num_err_categories; i++) {
+		const struct aie_err_category *category;
+		char errstr[AIE_SYSFS_ERROR_SIZE];
+		bool is_delimit_req = false;
+		bool err = false;
+		ssize_t l = 0;
+		u8 index;
+
+		category = &err_attr->err_category[i];
+		index = category->err_category;
+		for (j = 0; j < category->num_events; j++) {
+			u8 event = category->prop[j].event;
+			char *str = category->prop[j].event_str;
+
+			if (!aie_check_error_bitmap(apart, loc, module, event))
+				continue;
+
+			if (is_delimit_req) {
+				l += scnprintf(&errstr[l],
+					       max(0L, AIE_SYSFS_ERROR_SIZE - l),
+					       DELIMITER_LEVEL0);
+			}
+
+			l += scnprintf(&errstr[l],
+				       max(0L, AIE_SYSFS_ERROR_SIZE - l), str);
+			err = true;
+			is_delimit_req = true;
+		}
+
+		if (err) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 "%s: %s: %s\n", mod,
+					 aie_error_category_str[index], errstr);
+		}
+	}
+	return len;
+}
+
+/**
+ * aie_get_error_category_str() - returns error categories in string format.
+ *				  Errors categories are separated by a '|'
+ *				  symbol.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine tile.
+ * @module: module type.
+ * @err_attr: error attribute for given module type.
+ * @buffer: location to return error string.
+ * @size: total size of buffer available.
+ * @return: length of string copied to buffer.
+ */
+static ssize_t aie_get_error_category_str(struct aie_partition *apart,
+					  struct aie_location loc,
+					  enum aie_module_type module,
+					  const struct aie_error_attr *err_attr,
+					  char *buffer, ssize_t size)
+{
+	ssize_t len = 0;
+	u32 i, j;
+	bool is_delimit_req = false;
+
+	for (i = 0; i < err_attr->num_err_categories; i++) {
+		const struct aie_err_category *category;
+
+		category = &err_attr->err_category[i];
+		for (j = 0; j < category->num_events; j++) {
+			u8 event = category->prop[j].event;
+			u8 index = category->err_category;
+
+			if (!aie_check_error_bitmap(apart, loc, module, event))
+				continue;
+
+			if (is_delimit_req) {
+				len += scnprintf(&buffer[len], max(0L, size - len),
+						 DELIMITER_LEVEL0);
+			}
+
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					aie_error_category_str[index]);
+			is_delimit_req = true;
+			break;
+		}
+	}
+	return len;
+}
+
+/**
+ * aie_tile_show_error() - exports detailed error information to a tile level
+ *			   sysfs node.
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_tile_show_error(struct device *dev, struct device_attribute *attr,
+			    char *buffer)
+{
+	struct aie_tile *atile = container_of(dev, struct aie_tile, dev);
+	struct aie_partition *apart = atile->apart;
+	const struct aie_error_attr *core_attr, *mem_attr, *pl_attr;
+	ssize_t len = 0, size = PAGE_SIZE;
+	u32 ttype, core_count = 0, mem_count = 0, pl_count = 0;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, &atile->loc);
+	if (ttype == AIE_TILE_TYPE_TILE) {
+		core_attr = apart->adev->core_errors;
+		mem_attr = apart->adev->mem_errors;
+		core_count = aie_get_module_error_count(apart, atile->loc,
+							AIE_CORE_MOD,
+							core_attr);
+		mem_count = aie_get_module_error_count(apart, atile->loc,
+						       AIE_MEM_MOD, mem_attr);
+	} else {
+		pl_attr = apart->adev->shim_errors;
+		pl_count = aie_get_module_error_count(apart, atile->loc,
+						      AIE_PL_MOD, pl_attr);
+	}
+
+	if (!(core_count || mem_count || pl_count)) {
+		mutex_unlock(&apart->mlock);
+		return len;
+	}
+
+	if (core_count) {
+		len += aie_get_errors_str(apart, atile->loc, AIE_CORE_MOD,
+					  core_attr, &buffer[len], size - len);
+	}
+
+	if (mem_count) {
+		len += aie_get_errors_str(apart, atile->loc, AIE_MEM_MOD,
+					  mem_attr, &buffer[len], size - len);
+	}
+
+	if (pl_count) {
+		len += aie_get_errors_str(apart, atile->loc, AIE_PL_MOD,
+					  pl_attr, &buffer[len], size - len);
+	}
+
+	mutex_unlock(&apart->mlock);
+	return len;
+}
+
+/**
+ * aie_part_show_error_stat() - exports error count in a partition to a
+ *				partition level sysfs node.
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_show_error_stat(struct device *dev,
+				 struct device_attribute *attr, char *buffer)
+{
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_tile *atile = apart->atiles;
+	const struct aie_error_attr *core_attr, *mem_attr, *pl_attr;
+	ssize_t len = 0, size = PAGE_SIZE;
+	u32 index, core = 0, mem = 0, pl = 0;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++) {
+		u32 ttype = apart->adev->ops->get_tile_type(apart->adev,
+							    &atile->loc);
+
+		if (ttype == AIE_TILE_TYPE_TILE) {
+			core_attr = apart->adev->core_errors;
+			mem_attr = apart->adev->mem_errors;
+			core += aie_get_module_error_count(apart, atile->loc,
+							   AIE_CORE_MOD,
+							   core_attr);
+			mem += aie_get_module_error_count(apart, atile->loc,
+							  AIE_MEM_MOD,
+							  mem_attr);
+		} else {
+			pl_attr = apart->adev->shim_errors;
+			pl += aie_get_module_error_count(apart, atile->loc,
+							 AIE_PL_MOD, pl_attr);
+		}
+	}
+
+	mutex_unlock(&apart->mlock);
+
+	len += scnprintf(&buffer[len], max(0L, size - len), "core: %d\n", core);
+	len += scnprintf(&buffer[len], max(0L, size - len), "memory: %d\n",
+			 mem);
+	len += scnprintf(&buffer[len], max(0L, size - len), "pl: %d\n", pl);
+	return len;
+}
+
+/**
+ * aie_sysfs_get_errors() - returns all asserted error categories in string
+ *			    format. Error categories within module label,
+ *			    are separated by a '|' symbol.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine tile.
+ * @buffer: location to return error string.
+ * @size: total size of buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_sysfs_get_errors(struct aie_partition *apart,
+			     struct aie_location *loc, char *buffer,
+			     ssize_t size)
+{
+	u32 ttype, core_count = 0, mem_count = 0, pl_count = 0;
+	const struct aie_error_attr *core_attr, *mem_attr, *pl_attr;
+	ssize_t len = 0;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype == AIE_TILE_TYPE_TILE) {
+		core_attr = apart->adev->core_errors;
+		mem_attr = apart->adev->mem_errors;
+		core_count = aie_get_module_error_count(apart, *loc,
+							AIE_CORE_MOD,
+							core_attr);
+		mem_count  = aie_get_module_error_count(apart, *loc,
+							AIE_MEM_MOD, mem_attr);
+	} else {
+		pl_attr = apart->adev->shim_errors;
+		pl_count = aie_get_module_error_count(apart, *loc, AIE_PL_MOD,
+						      pl_attr);
+	}
+
+	if (!(core_count || mem_count || pl_count))
+		return len;
+
+	len += scnprintf(&buffer[len], max(0L, size - len), "%d_%d: ", loc->col,
+			 loc->row);
+
+	if (core_count) {
+		len += scnprintf(&buffer[len], max(0L, size - len), "core: ");
+		len += aie_get_error_category_str(apart, *loc, AIE_CORE_MOD,
+						  core_attr, &buffer[len],
+						  size - len);
+	}
+
+	if (mem_count) {
+		len += scnprintf(&buffer[len], max(0L, size - len), "%smemory: ",
+				 core_count ? DELIMITER_LEVEL1 : "");
+		len += aie_get_error_category_str(apart, *loc, AIE_MEM_MOD,
+						  mem_attr, &buffer[len],
+						  size - len);
+	}
+
+	if (pl_count) {
+		len += scnprintf(&buffer[len], max(0L, size - len), "pl: ");
+		len += aie_get_error_category_str(apart, *loc, AIE_PL_MOD,
+						  pl_attr, &buffer[len],
+						  size - len);
+	}
+
+	len += scnprintf(&buffer[len], max(0L, size - len), "\n");
+	return len;
+}
+
+/**
+ * aie_part_read_cb_error() - exports errors with a given partition to
+ *			      partition level node.
+ * @kobj: kobject used to create sysfs node.
+ * @buffer: export buffer.
+ * @size: length of export buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_read_cb_error(struct kobject *kobj, char *buffer, ssize_t size)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_tile *atile = apart->atiles;
+	ssize_t len = 0;
+	u32 index;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	if (!(aie_get_error_count(apart))) {
+		mutex_unlock(&apart->mlock);
+		return len;
+	}
+
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++) {
+		len += aie_sysfs_get_errors(apart, &atile->loc, &buffer[len],
+					    size - len);
+	}
+
+	mutex_unlock(&apart->mlock);
+	return len;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-event.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-event.c
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver.
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+
+/**
+ * aie_tile_print_event() - formats events strings from each module into a
+ *			    single buffer.
+ * @atile: AI engine tile.
+ * @buffer: export buffer.
+ * @core: core module event string
+ * @mem: memory module event string
+ * @pl: pl module event string
+ * @return: length of string copied to buffer.
+ */
+static ssize_t aie_tile_print_event(struct aie_tile *atile, char *buffer,
+				    char *core, char *mem, char *pl)
+{
+	ssize_t len = 0, size = PAGE_SIZE;
+	u32 ttype;
+
+	ttype = atile->apart->adev->ops->get_tile_type(atile->apart->adev,
+						       &atile->loc);
+	if (ttype == AIE_TILE_TYPE_TILE) {
+		len += scnprintf(&buffer[len], max(0L, size - len),
+				 "core: %s\n", core);
+		len += scnprintf(&buffer[len], max(0L, size - len),
+				 "memory: %s\n", mem);
+	} else {
+		len += scnprintf(&buffer[len], max(0L, size - len), "pl: %s\n",
+				 pl);
+	}
+	return len;
+}
+
+/**
+ * aie_tile_show_event() - exports all active events in a given tile to a
+ *			   tile level sysfs node.
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_tile_show_event(struct device *dev, struct device_attribute *attr,
+			    char *buffer)
+{
+	struct aie_tile *atile = container_of(dev, struct aie_tile, dev);
+	struct aie_partition *apart = atile->apart;
+	ssize_t l = 0;
+	unsigned long cs[4] = {0}, ms[4] = {0}, ps[4] = {0};
+	u32 ttype, n;
+	char core_buf[AIE_SYSFS_EVENT_STS_SIZE],
+	     mem_buf[AIE_SYSFS_EVENT_STS_SIZE],
+	     pl_buf[AIE_SYSFS_EVENT_STS_SIZE];
+	bool is_delimit_req = false;
+
+	/*
+	 * Initialize local buffers to avoid garbage data being returned to the
+	 * export buffer.
+	 */
+	core_buf[0] = '\0';
+	mem_buf[0] = '\0';
+	pl_buf[0] = '\0';
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return 0;
+	}
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, &atile->loc);
+
+	if (!aie_part_check_clk_enable_loc(apart, &atile->loc)) {
+		mutex_unlock(&apart->mlock);
+		return aie_tile_print_event(atile, buffer, "clock_gated",
+					    "clock_gated", "clock_gated");
+	}
+
+	if (ttype == AIE_TILE_TYPE_TILE) {
+		aie_read_event_status(apart, &atile->loc, AIE_CORE_MOD,
+				      (u32 *)cs);
+		aie_read_event_status(apart, &atile->loc, AIE_MEM_MOD,
+				      (u32 *)ms);
+	} else {
+		aie_read_event_status(apart, &atile->loc, AIE_PL_MOD,
+				      (u32 *)ps);
+	}
+
+	for_each_set_bit(n, cs, 128) {
+		if (is_delimit_req) {
+			l += scnprintf(&core_buf[l],
+				       max(0L, AIE_SYSFS_EVENT_STS_SIZE - l),
+				       DELIMITER_LEVEL0);
+		}
+
+		l += scnprintf(&core_buf[l],
+			       max(0L, AIE_SYSFS_EVENT_STS_SIZE - l), "%d", n);
+		is_delimit_req = true;
+	}
+
+	l = 0;
+	is_delimit_req = false;
+	for_each_set_bit(n, ms, 128) {
+		if (is_delimit_req) {
+			l += scnprintf(&mem_buf[l],
+				       max(0L, AIE_SYSFS_EVENT_STS_SIZE - l),
+				       DELIMITER_LEVEL0);
+		}
+
+		l += scnprintf(&mem_buf[l],
+			       max(0L, AIE_SYSFS_EVENT_STS_SIZE - l), "%d", n);
+		is_delimit_req = true;
+	}
+
+	l = 0;
+	is_delimit_req = false;
+	for_each_set_bit(n, ps, 128) {
+		if (is_delimit_req) {
+			l += scnprintf(&pl_buf[l],
+				       max(0L, AIE_SYSFS_EVENT_STS_SIZE - l),
+				       DELIMITER_LEVEL0);
+		}
+
+		l += scnprintf(&pl_buf[l],
+			       max(0L, AIE_SYSFS_EVENT_STS_SIZE - l), "%d", n);
+		is_delimit_req = true;
+	}
+
+	mutex_unlock(&apart->mlock);
+	return aie_tile_print_event(atile, buffer, core_buf, mem_buf, pl_buf);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-lock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-lock.c
@@ -0,0 +1,184 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver.
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+
+/**
+ * aie_get_lock_status() - reads the lock status.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine DMA.
+ * @return: 32-bit register value.
+ */
+static u32 aie_get_lock_status(struct aie_partition *apart,
+			       struct aie_location *loc)
+{
+	u32 ttype, stsoff, regoff;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		stsoff = apart->adev->pl_lock->sts_regoff;
+	else
+		stsoff = apart->adev->mem_lock->sts_regoff;
+	regoff = aie_cal_regoff(apart->adev, *loc, stsoff);
+	return ioread32(apart->aperture->base + regoff);
+}
+
+/**
+ * aie_get_lock_status_str() - returns the string value corresponding to
+ *			       lock status value.
+ * @apart: AI engine partition.
+ * @loc: location of AI engine lock.
+ * @status: status value of lock.
+ * @lock: lock ID.
+ * @buffer: location to return lock status string.
+ * @size: total size of buffer available.
+ * @return: length of string copied to buffer.
+ */
+static ssize_t aie_get_lock_status_str(struct aie_partition *apart,
+				       struct aie_location *loc, u32 status,
+				       u32 lock, char *buffer, ssize_t size)
+{
+	char **str = apart->adev->lock_status_str;
+	u32 ttype, mask;
+	u8 value, shift;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype != AIE_TILE_TYPE_TILE) {
+		shift = lock * apart->adev->pl_lock->sts.regoff;
+		mask = (apart->adev->pl_lock->sts.mask) << shift;
+	} else {
+		shift = lock * apart->adev->mem_lock->sts.regoff;
+		mask = (apart->adev->mem_lock->sts.mask) << shift;
+	}
+
+	value = (status & mask) >> shift;
+	return scnprintf(buffer, max(0L, size), str[value]);
+}
+
+/**
+ * aie_tile_show_lock() - exports AI engine lock status to a tile level sysfs
+ *			  node.
+ * @dev: AI engine tile device.
+ * @attr: sysfs device attribute.
+ * @buffer: export buffer.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_tile_show_lock(struct device *dev, struct device_attribute *attr,
+			   char *buffer)
+{
+	struct aie_tile *atile = container_of(dev, struct aie_tile, dev);
+	struct aie_partition *apart = atile->apart;
+	ssize_t len = 0, size = PAGE_SIZE;
+	unsigned long status;
+	u32 ttype, i, num_locks;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, &atile->loc);
+	if (ttype != AIE_TILE_TYPE_TILE)
+		num_locks = apart->adev->pl_lock->num_locks;
+	else
+		num_locks = apart->adev->mem_lock->num_locks;
+
+	if (!aie_part_check_clk_enable_loc(apart, &atile->loc)) {
+		for (i = 0; i < num_locks; i++) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 "%d: clock_gated\n", i);
+		}
+		mutex_unlock(&apart->mlock);
+		return len;
+	}
+
+	status = aie_get_lock_status(apart, &atile->loc);
+	for (i = 0; i < num_locks; i++) {
+		len += scnprintf(&buffer[len], max(0L, size - len), "%d: ", i);
+		len += aie_get_lock_status_str(apart, &atile->loc, status, i,
+					       &buffer[len], size - len);
+		len += scnprintf(&buffer[len], max(0L, size - len), "\n");
+	}
+	mutex_unlock(&apart->mlock);
+	return len;
+}
+
+ssize_t aie_sysfs_get_lock_status(struct aie_partition *apart,
+				  struct aie_location *loc, char *buffer,
+				  ssize_t size)
+{
+	u32 i, ttype, num_locks;
+	unsigned long status;
+	ssize_t len = 0;
+
+	ttype = apart->adev->ops->get_tile_type(apart->adev, loc);
+	if (ttype == AIE_TILE_TYPE_SHIMPL)
+		return len;
+
+	if (!aie_part_check_clk_enable_loc(apart, loc)) {
+		len += scnprintf(&buffer[len], max(0L, size - len),
+				 "clock_gated");
+		return len;
+	}
+
+	if (ttype != AIE_TILE_TYPE_TILE)
+		num_locks = apart->adev->pl_lock->num_locks;
+	else
+		num_locks = apart->adev->mem_lock->num_locks;
+
+	status = aie_get_lock_status(apart, loc);
+	for (i = 0; i < num_locks; i++) {
+		len += aie_get_lock_status_str(apart, loc, status, i,
+					       &buffer[len], size - len);
+		if (i < num_locks - 1) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 DELIMITER_LEVEL0);
+		}
+	}
+	return len;
+}
+
+/**
+ * aie_part_read_cb_lock() - exports status of all lock modules within a given
+ *			     partition to partition level node.
+ * @kobj: kobject used to create sysfs node.
+ * @buffer: export buffer.
+ * @size: length of export buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_read_cb_lock(struct kobject *kobj, char *buffer, ssize_t size)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_tile *atile = apart->atiles;
+	ssize_t len = 0;
+	u32 index;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++) {
+		u32 ttype = apart->adev->ops->get_tile_type(apart->adev,
+							    &atile->loc);
+
+		if (ttype == AIE_TILE_TYPE_SHIMPL)
+			continue;
+
+		len += scnprintf(&buffer[len], max(0L, size - len), "%d_%d: ",
+				 atile->loc.col, atile->loc.row);
+		len += aie_sysfs_get_lock_status(apart, &atile->loc,
+						 &buffer[len], size - len);
+		len += scnprintf(&buffer[len], max(0L, size - len), "\n");
+	}
+
+	mutex_unlock(&apart->mlock);
+	return len;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-status.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs-status.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine driver AIE device specific implementation
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include <linux/slab.h>
+
+#include "ai-engine-internal.h"
+
+/**
+ * aie_part_read_cb_status() - exports status of cores, DMAs, errors, and locks
+ *			       within a partition at a partition level node.
+ *			       this node serves as a single access point to
+ *			       query the status of a partition by a
+ *			       script/tool. For a given tile location, core
+ *			       status, DMAs, etc are separated by a ';' symbol.
+ *			       Core status information is captured under 'cs'
+ *			       label, DMA under 'ds', errors under 'es', and
+ *			       lock status under 'ls'.
+ * @kobj: kobject used to create sysfs node.
+ * @buffer: export buffer.
+ * @size: length of export buffer available.
+ * @return: length of string copied to buffer.
+ */
+ssize_t aie_part_read_cb_status(struct kobject *kobj, char *buffer,
+				ssize_t size)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct aie_partition *apart = dev_to_aiepart(dev);
+	struct aie_tile *atile = apart->atiles;
+	ssize_t len = 0;
+	size_t temp_size = AIE_SYSFS_CORE_STS_SIZE + AIE_SYSFS_CHAN_STS_SIZE +
+			   AIE_SYSFS_ERROR_CATEGORY_SIZE +
+			   AIE_SYSFS_LOCK_STS_SIZE;
+	char *cs_buf, *ds_buf, *es_buf, *ls_buf;
+	u32 index;
+
+	if (mutex_lock_interruptible(&apart->mlock)) {
+		dev_err(&apart->dev,
+			"Failed to acquire lock. Process was interrupted by fatal signals\n");
+		return len;
+	}
+
+	cs_buf = kmalloc(temp_size, GFP_KERNEL);
+	if (!cs_buf) {
+		mutex_unlock(&apart->mlock);
+		return len;
+	}
+
+	ds_buf = cs_buf + AIE_SYSFS_CORE_STS_SIZE;
+	es_buf = ds_buf + AIE_SYSFS_CHAN_STS_SIZE;
+	ls_buf = es_buf + AIE_SYSFS_ERROR_CATEGORY_SIZE;
+
+	for (index = 0; index < apart->range.size.col * apart->range.size.row;
+	     index++, atile++) {
+		u32 cs = 0, ds = 0, es = 0, ls = 0;
+
+		cs = aie_sysfs_get_core_status(apart, &atile->loc, cs_buf,
+					       AIE_SYSFS_CORE_STS_SIZE);
+		ds = aie_sysfs_get_dma_status(apart, &atile->loc, ds_buf,
+					      AIE_SYSFS_CHAN_STS_SIZE);
+		es = aie_sysfs_get_errors(apart, &atile->loc, es_buf,
+					  AIE_SYSFS_ERROR_CATEGORY_SIZE);
+		ls = aie_sysfs_get_lock_status(apart, &atile->loc, ls_buf,
+					       AIE_SYSFS_LOCK_STS_SIZE);
+
+		if (!(cs || ds || es || ls))
+			continue;
+
+		len += scnprintf(&buffer[len], max(0L, size - len), "%d_%d: ",
+				 atile->loc.col, atile->loc.row);
+
+		if (cs) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 "cs: %s", cs_buf);
+		}
+
+		if (ds) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 "%sds: %s", cs ?
+					 DELIMITER_LEVEL2 : "", ds_buf);
+		}
+
+		if (es) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 "%ses: %s", (cs || ds) ?
+					 DELIMITER_LEVEL2 : "", es_buf);
+		}
+
+		if (ls) {
+			len += scnprintf(&buffer[len], max(0L, size - len),
+					 "%sls: %s", (cs || ds || es) ?
+					 DELIMITER_LEVEL2 : "", ls_buf);
+		}
+
+		len += scnprintf(&buffer[len], max(0L, size - len), "\n");
+	}
+
+	mutex_unlock(&apart->mlock);
+	kfree(cs_buf);
+	return len;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx-ai-engine/ai-engine-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx-ai-engine/ai-engine-sysfs.c
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AI Engine device driver.
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+#include "ai-engine-internal.h"
+
+/**
+ * aie_sysfs_read_handler() - sysfs binary attribute read handler.
+ * @filp: file pointer.
+ * @kobj: pointer to the kobject.
+ * @attr: sysfs binary attribute.
+ * @buf: buffer to copy the data to.
+ * @offset: offset into the sysfs file.
+ * @max_size: maximum length of data that could be copied to buf.
+ * @return: length of data actually copied to buf.
+ */
+ssize_t aie_sysfs_read_handler(struct file *filp, struct kobject *kobj,
+			       struct bin_attribute *attr, char *buf,
+			       loff_t offset, size_t max_size)
+{
+	ssize_t len = max_size;
+	struct aie_sysfs_prop *prop;
+
+	prop = attr->private;
+	if (!prop->data)
+		return 0;
+
+	if (!offset)
+		prop->size = prop->read_callback(kobj, prop->data,
+						 prop->max_size);
+
+	if (offset >= prop->size)
+		return 0;
+
+	if (offset + max_size > prop->size)
+		len = prop->size - offset;
+
+	memcpy(buf,  prop->data + offset, len);
+	return len;
+}
+
+/**
+ * aie_sysfs_create_dev_attr() - dynamically allocates and initialize a device
+ *				 attribute
+ * @dev: device to allocate attribute for.
+ * @attr: AI engine device attribute.
+ * @return: pointer to the allocated device attribute.
+ */
+static struct device_attribute *
+aie_sysfs_create_dev_attr(struct device *dev, const struct aie_dev_attr *attr)
+{
+	struct device_attribute *node;
+
+	node = devm_kzalloc(dev, sizeof(struct device_attribute), GFP_KERNEL);
+	if (!node)
+		return ERR_PTR(-ENOMEM);
+
+	sysfs_attr_init(&node->attr);
+
+	node->attr.name = attr->name;
+	node->attr.mode = attr->mode;
+	node->show = attr->show;
+	return node;
+}
+
+/**
+ * aie_sysfs_create_bin_attr() - dynamically allocates and initialize a binary
+ *				 attribute
+ * @dev: device to allocate attribute for.
+ * @attr: AI engine binary attribute.
+ * @return: pointer to the allocated binary attribute.
+ */
+static struct bin_attribute *
+aie_sysfs_create_bin_attr(struct device *dev, const struct aie_bin_attr *attr)
+{
+	struct bin_attribute *node;
+	struct aie_sysfs_prop *prop;
+
+	node = devm_kzalloc(dev, sizeof(struct bin_attribute), GFP_KERNEL);
+	if (!node)
+		return ERR_PTR(-ENOMEM);
+
+	sysfs_bin_attr_init(node);
+
+	node->attr.name = attr->name;
+	node->attr.mode = attr->mode;
+	node->size = attr->size;
+	node->read = attr->read;
+
+	prop = devm_kzalloc(dev, sizeof(struct aie_sysfs_prop), GFP_KERNEL);
+	if (!prop)
+		return ERR_PTR(-ENOMEM);
+
+	prop->data = devm_kzalloc(dev, node->size, GFP_KERNEL);
+	if (!prop->data)
+		return ERR_PTR(-ENOMEM);
+
+	prop->max_size = node->size;
+	prop->read_callback = attr->read_callback;
+	node->private = prop;
+	return node;
+}
+
+/**
+ * aie_tile_sysfs_create() - creates sysfs nodes at the tile level.
+ * @atile: AI engine tile.
+ * @return: 0 for success, error code for failure.
+ */
+static int aie_tile_sysfs_create(struct aie_tile *atile)
+{
+	struct attribute_group *attr_grp;
+	struct bin_attribute **bin_attrs;
+	struct attribute **dev_attrs;
+	const struct aie_sysfs_attr *attr;
+	int ret = 0;
+	u32 ttype;
+	u32 index, i = 0, j = 0;
+
+	attr = atile->apart->adev->tile_sysfs_attr;
+	ttype = atile->apart->adev->ops->get_tile_type(atile->apart->adev,
+						       &atile->loc);
+
+	if (attr->num_dev_attrs) {
+		dev_attrs = devm_kzalloc(&atile->dev, sizeof(*dev_attrs) *
+					 (attr->num_dev_attrs + 1), GFP_KERNEL);
+		if (!dev_attrs)
+			return -ENOMEM;
+
+		for (index = 0; index < attr->num_dev_attrs; index++) {
+			struct device_attribute *node;
+			const struct aie_dev_attr *dev_attr;
+
+			dev_attr = &attr->dev_attr[index];
+
+			if (!(BIT(ttype) & attr->dev_attr[index].tile_type))
+				continue;
+
+			node = aie_sysfs_create_dev_attr(&atile->dev, dev_attr);
+			if (IS_ERR_VALUE(node))
+				return PTR_ERR(node);
+
+			dev_attrs[i++] = &node->attr;
+		}
+	}
+
+	if (attr->num_bin_attrs) {
+		bin_attrs = devm_kzalloc(&atile->dev, sizeof(*bin_attrs) *
+					 (attr->num_bin_attrs + 1), GFP_KERNEL);
+		if (!bin_attrs)
+			return -ENOMEM;
+
+		for (index = 0; index < attr->num_bin_attrs; index++) {
+			struct bin_attribute *node;
+			const struct aie_bin_attr *bin_attr;
+
+			bin_attr = &attr->bin_attr[index];
+
+			if (!(BIT(ttype) & attr->bin_attr[index].tile_type))
+				continue;
+
+			node = aie_sysfs_create_bin_attr(&atile->dev, bin_attr);
+			if (IS_ERR_VALUE(node))
+				return PTR_ERR(node);
+
+			bin_attrs[j++] = node;
+		}
+	}
+
+	if (attr->num_dev_attrs || attr->num_bin_attrs) {
+		attr_grp = devm_kzalloc(&atile->dev,
+					sizeof(struct attribute_group),
+					GFP_KERNEL);
+		if (!attr_grp)
+			return -ENOMEM;
+
+		atile->attr_grp = attr_grp;
+
+		if (attr->num_dev_attrs)
+			attr_grp->attrs = dev_attrs;
+
+		if (attr->num_bin_attrs)
+			attr_grp->bin_attrs = bin_attrs;
+
+		/* TODO - use the non managed api to create sysfs group.
+		 * This workaround solves an issue where the device_del()
+		 * removes the SYSFS files before the managed create group.
+		 * This results in an error where files cannot be found.
+		 */
+		ret = sysfs_create_group(&atile->dev.kobj, attr_grp);
+		if (ret) {
+			dev_err(&atile->dev,
+				"Failed to add sysfs attributes group\n");
+		}
+	}
+	return ret;
+}
+
+/**
+ * aie_part_sysfs_create() - creates sysfs nodes at the partition level.
+ * @apart: AI engine partition.
+ * @return: 0 for success, error code for failure.
+ */
+static int aie_part_sysfs_create(struct aie_partition *apart)
+{
+	const struct aie_sysfs_attr *attr;
+	struct attribute_group *attr_grp;
+	struct bin_attribute **bin_attrs;
+	struct attribute **dev_attrs;
+	int ret = 0;
+	u32 index;
+
+	attr = apart->adev->part_sysfs_attr;
+
+	if (attr->num_dev_attrs) {
+		dev_attrs = devm_kzalloc(&apart->dev, sizeof(*dev_attrs) *
+					 (attr->num_dev_attrs + 1), GFP_KERNEL);
+		if (!dev_attrs)
+			return -ENOMEM;
+
+		for (index = 0; index < attr->num_dev_attrs; index++) {
+			struct device_attribute *node;
+			const struct aie_dev_attr *dev_attr;
+
+			dev_attr = &attr->dev_attr[index];
+
+			node = aie_sysfs_create_dev_attr(&apart->dev, dev_attr);
+			if (IS_ERR_VALUE(node))
+				return PTR_ERR(node);
+
+			dev_attrs[index] = &node->attr;
+		}
+	}
+
+	if (attr->num_bin_attrs) {
+		bin_attrs = devm_kzalloc(&apart->dev, sizeof(*bin_attrs) *
+					 (attr->num_bin_attrs + 1), GFP_KERNEL);
+		if (!bin_attrs)
+			return -ENOMEM;
+
+		for (index = 0; index < attr->num_bin_attrs; index++) {
+			struct bin_attribute *node;
+			const struct aie_bin_attr *bin_attr;
+
+			bin_attr = &attr->bin_attr[index];
+
+			node = aie_sysfs_create_bin_attr(&apart->dev, bin_attr);
+			if (IS_ERR_VALUE(node))
+				return PTR_ERR(node);
+
+			bin_attrs[index] = node;
+		}
+	}
+
+	if (attr->num_dev_attrs || attr->num_bin_attrs) {
+		attr_grp = devm_kzalloc(&apart->dev,
+					sizeof(struct attribute_group),
+					GFP_KERNEL);
+		if (!attr_grp)
+			return -ENOMEM;
+
+		apart->attr_grp = attr_grp;
+
+		if (attr->num_dev_attrs)
+			attr_grp->attrs = dev_attrs;
+
+		if (attr->num_bin_attrs)
+			attr_grp->bin_attrs = bin_attrs;
+
+		/* TODO - use the non managed api to create sysfs group.
+		 * This workaround solves an issue where the device_del()
+		 * removes the SYSFS files before the managed create group.
+		 * This results in an error where files cannot be found.
+		 */
+		ret = sysfs_create_group(&apart->dev.kobj, attr_grp);
+		if (ret) {
+			dev_err(&apart->dev,
+				"Failed to add sysfs attributes group\n");
+		}
+	}
+	return ret;
+}
+
+/**
+ * aie_part_sysfs_create_entries() - creates sysfs group for partition device.
+ * @apart: AI engine partition.
+ * @return: 0 for success, error code for failure.
+ */
+int aie_part_sysfs_create_entries(struct aie_partition *apart)
+{
+	int ret;
+
+	/*
+	 * TODO: hardware monitoring and dump using sysfs is not supported for
+	 * AIEML as of now.
+	 */
+	if (apart->adev->dev_gen == AIE_DEVICE_GEN_AIEML) {
+		dev_dbg(&apart->dev, "Not creating sysfs entries..\n");
+		return 0;
+	}
+
+	ret = aie_part_sysfs_create(apart);
+	if (ret < 0) {
+		dev_err(&apart->dev, "Failed to create sysfs partition\n");
+		return ret;
+	}
+	return ret;
+}
+
+/**
+ * aie_tile_sysfs_create_entries() - creates sysfs group for tile device.
+ * @atile: AI engine tile.
+ * @return: 0 for success, error code for failure.
+ */
+int aie_tile_sysfs_create_entries(struct aie_tile *atile)
+{
+	int ret;
+
+	ret = aie_tile_sysfs_create(atile);
+	if (ret < 0) {
+		dev_err(&atile->dev, "Failed to create sysfs tile\n");
+		return ret;
+	}
+	return ret;
+}
+
+/**
+ * aie_part_sysfs_remove_entries() - removes sysfs group from partition device.
+ * @apart: AI engine partition.
+ */
+void aie_part_sysfs_remove_entries(struct aie_partition *apart)
+{
+	sysfs_remove_group(&apart->dev.kobj, apart->attr_grp);
+}
+
+/**
+ * aie_tile_sysfs_remove_entries() - removes sysfs group from tile device.
+ * @atile: AI engine tile.
+ */
+void aie_tile_sysfs_remove_entries(struct aie_tile *atile)
+{
+	sysfs_remove_group(&atile->dev.kobj, atile->attr_grp);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx_flex_pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx_flex_pm.c
@@ -0,0 +1,610 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Flex Noc Performance Monitor driver.
+ * Copyright (c) 2019 Xilinx Inc.
+ */
+
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define to_xflex_dev_info(n)	((struct xflex_dev_info *)dev_get_drvdata(n))
+
+#define FPM_LAR_OFFSET			0xFB0
+#define FPM_UNLOCK			0xC5ACCE55
+
+#define FPM_RD_REQ_OFFSET		0x1000
+#define FPM_RD_RES_OFFSET		0x2000
+#define FPM_WR_REQ_OFFSET		0x3000
+#define FPM_WR_RES_OFFSET		0x4000
+
+#define FPM_PORT_SEL_OFFSET		0x134
+#define FPM_MAIN_CTRL_OFFSET		0x008
+#define FPM_SRC_SEL_OFFSET		0x138
+#define FPM_STATPERIOD			0x24
+#define FPM_CFGCTRL			0x0C
+#define FPM_LPD				0x4210002
+#define FPM_FPD				0x420c003
+
+#define FPM_VAL				0x300
+#define FPM_SRC				0x200
+#define FPM_WRRSP_L			0x70000
+#define FPM_WRREQ_L			0x60000
+#define FPM_RDRSP_L			0x50000
+#define FPM_RDREQ_L			0x40000
+
+#define FPM_WRRSP_FPD			0x30000
+#define FPM_WRREQ_FPD			0x20000
+#define FPM_RDRSP_FPD			0x10000
+#define FPM_RDREQ_FPD			0x0
+
+#define FPM_PROBE_SHIFT			16
+#define FPM_COUNTER_OFFSET		0x14
+#define FPM_GLOBALEN			BIT(0)
+#define FPM_STATEN			BIT(3)
+#define FPM_STATCOND_DUMP		BIT(5)
+#define FPM_NUM_COUNTERS		4
+#define FPM_MAINCTL_DIS			0
+
+#define FPM_SRC_OFF			0x0
+#define FPM_SRC_CYCLE			0x1
+#define FPM_SRC_IDLE			0x2
+#define FPM_SRC_XFER			0x3
+#define FPM_SRC_BUSY			0x4
+#define FPM_SRC_WAIT			0x5
+#define FPM_SRC_PACKET			0x6
+
+/* Port values */
+#define FPM_PORT_LPD_AFIFS_AXI		0x0
+#define FPM_PORT_LPD_OCM		0x1
+#define FPM_PORT_LPD_OCMEXT		0x2
+#define FPM_PORT_PMC_RPU_AXI0		0x3
+
+#define FPM_PORT_FPDAXI			0x1
+#define FPM_PORT_PROTXPPU		0x2
+
+/**
+ * struct xflex_dev_info - Global Driver structure
+ * @dev: Device structure
+ * @baselpd: Iomapped LPD base address
+ * @basefpd: Iomapped FPD base address
+ * @funnel: Iomapped funnel register base address
+ * @counterid_lpd: LPD counter id
+ * @counterid_fpd: FPD counter id
+ * @mutex: avoid parallel access to device
+ */
+struct xflex_dev_info {
+	struct device *dev;
+	void __iomem *baselpd;
+	void __iomem *basefpd;
+	void __iomem *funnel;
+	u32 counterid_fpd;
+	u32 counterid_lpd;
+	struct mutex mutex; /* avoid parallel access to device */
+};
+
+/**
+ * enum xflex_sysfs_cmd_codes - sysfs command codes
+ * @XFLEX_GET_COUNTER_FPD: get the FPD counter value
+ * @XFLEX_SET_COUNTER_FPD: set the FPD counter value
+ * @XFLEX_GET_COUNTER_FPD_RDREQ: get the FPD read request count
+ * @XFLEX_GET_COUNTER_FPD_RDRSP: get the FPD read response count
+ * @XFLEX_GET_COUNTER_FPD_WRREQ: get the FPD write request count
+ * @XFLEX_GET_COUNTER_FPD_WRRSP: get the FPD write response count
+ * @XFLEX_GET_COUNTER_LPD_RDREQ: get the LPD read request count
+ * @XFLEX_GET_COUNTER_LPD_RDRSP: get the LPD read response count
+ * @XFLEX_GET_COUNTER_LPD_WRREQ: get the LPD write request count
+ * @XFLEX_GET_COUNTER_LPD_WRRSP: get the LPD write response count
+ * @XFLEX_SET_COUNTER_LPD: set the LPD counter value
+ * @XFLEX_SET_SRC_COUNTER_LPD: set the LPD source
+ * @XFLEX_SET_SRC_COUNTER_FPD: set the FPD source
+ * @XFLEX_SET_PORT_COUNTER_LPD: set the LPD port
+ * @XFLEX_SET_PORT_COUNTER_FPD: set the FPD port
+ */
+enum xflex_sysfs_cmd_codes {
+	XFLEX_GET_COUNTER_FPD = 0,
+	XFLEX_SET_COUNTER_FPD,
+	XFLEX_GET_COUNTER_FPD_RDREQ,
+	XFLEX_GET_COUNTER_FPD_RDRSP,
+	XFLEX_GET_COUNTER_FPD_WRREQ,
+	XFLEX_GET_COUNTER_FPD_WRRSP,
+	XFLEX_GET_COUNTER_LPD_RDREQ,
+	XFLEX_GET_COUNTER_LPD_RDRSP,
+	XFLEX_GET_COUNTER_LPD_WRREQ,
+	XFLEX_GET_COUNTER_LPD_WRRSP,
+	XFLEX_SET_COUNTER_LPD,
+	XFLEX_SET_SRC_COUNTER_LPD,
+	XFLEX_SET_SRC_COUNTER_FPD,
+	XFLEX_SET_PORT_COUNTER_LPD,
+	XFLEX_SET_PORT_COUNTER_FPD,
+};
+
+static inline void fpm_reg(void __iomem *base, u32 val, u32 offset)
+{
+	writel(val, base + FPM_RD_REQ_OFFSET + offset);
+	writel(val, base + FPM_RD_RES_OFFSET + offset);
+	writel(val, base + FPM_WR_REQ_OFFSET + offset);
+	writel(val, base + FPM_WR_RES_OFFSET + offset);
+}
+
+static void reset_default(struct device *dev, u32 counter, u32 domain)
+{
+	struct xflex_dev_info *flexpm = to_xflex_dev_info(dev);
+	void __iomem *base = flexpm->basefpd;
+	u32 offset;
+
+	if (domain == FPM_LPD)
+		base = flexpm->baselpd;
+
+	fpm_reg(base, FPM_MAINCTL_DIS, FPM_MAIN_CTRL_OFFSET);
+	fpm_reg(base, FPM_STATEN | FPM_STATCOND_DUMP, FPM_MAIN_CTRL_OFFSET);
+	fpm_reg(base, FPM_STATEN | FPM_STATCOND_DUMP, FPM_MAIN_CTRL_OFFSET);
+
+	offset = FPM_PORT_SEL_OFFSET + counter * FPM_COUNTER_OFFSET;
+	fpm_reg(base, FPM_PORT_LPD_OCM, offset);
+	offset = FPM_SRC_SEL_OFFSET + counter * FPM_COUNTER_OFFSET;
+	fpm_reg(base, FPM_SRC_PACKET, offset);
+
+	fpm_reg(base, 0, FPM_STATPERIOD);
+	fpm_reg(base, FPM_GLOBALEN, FPM_CFGCTRL);
+}
+
+/**
+ * xflex_sysfs_cmd - Implements sysfs operations
+ * @dev: Device structure
+ * @buf: Value to write
+ * @cmd: sysfs cmd
+ *
+ * Return: value read from the sysfs cmd on success and negative error code
+ *		otherwise.
+ */
+static int xflex_sysfs_cmd(struct device *dev, const char *buf,
+			   enum xflex_sysfs_cmd_codes cmd)
+{
+	struct xflex_dev_info *flexpm = to_xflex_dev_info(dev);
+	u32 domain, src, offset, reg, val, counter;
+	int ret;
+	u32 pm_api_ret[4] = {0, 0, 0, 0};
+
+	mutex_lock(&flexpm->mutex);
+
+	switch (cmd) {
+	case XFLEX_GET_COUNTER_LPD_WRRSP:
+		reg = flexpm->counterid_lpd | FPM_WRRSP_L | FPM_VAL;
+		domain = FPM_LPD;
+
+		break;
+
+	case XFLEX_GET_COUNTER_LPD_WRREQ:
+		reg = flexpm->counterid_lpd | FPM_WRRSP_L | FPM_VAL;
+		domain = FPM_LPD;
+
+		break;
+
+	case XFLEX_GET_COUNTER_LPD_RDRSP:
+		reg = flexpm->counterid_lpd | FPM_RDRSP_L | FPM_VAL;
+		domain = FPM_LPD;
+
+		break;
+
+	case XFLEX_GET_COUNTER_LPD_RDREQ:
+		reg = flexpm->counterid_lpd | FPM_RDREQ_L | FPM_VAL;
+		domain = FPM_LPD;
+
+		break;
+
+	case XFLEX_SET_COUNTER_LPD:
+		ret = kstrtou32(buf, 0, &val);
+		if (ret < 0)
+			goto exit_unlock;
+
+		flexpm->counterid_lpd = val;
+		reset_default(dev, val, FPM_LPD);
+		goto exit_unlock;
+
+	case XFLEX_SET_PORT_COUNTER_FPD:
+		ret = kstrtou32(buf, 0, &val);
+		if (ret < 0)
+			goto exit_unlock;
+
+		counter = flexpm->counterid_fpd * FPM_COUNTER_OFFSET;
+		offset = FPM_PORT_SEL_OFFSET + counter * FPM_COUNTER_OFFSET;
+		fpm_reg(flexpm->basefpd, val, offset);
+		goto exit_unlock;
+
+	case XFLEX_SET_PORT_COUNTER_LPD:
+		ret = kstrtou32(buf, 0, &val);
+		if (ret < 0)
+			goto exit_unlock;
+
+		counter = flexpm->counterid_lpd * FPM_COUNTER_OFFSET;
+		offset = FPM_PORT_SEL_OFFSET + counter * FPM_COUNTER_OFFSET;
+		fpm_reg(flexpm->baselpd, val, offset);
+		goto exit_unlock;
+
+	case XFLEX_SET_SRC_COUNTER_LPD:
+		reg = flexpm->counterid_lpd;
+		domain = FPM_LPD;
+		ret = kstrtou32(buf, 0, &val);
+		if (ret < 0)
+			goto exit_unlock;
+
+		for (src = 0; src < FPM_NUM_COUNTERS; src++) {
+			reg = reg | FPM_SRC | (src << FPM_PROBE_SHIFT);
+			ret = zynqmp_pm_probe_counter_write(domain, reg, val);
+			if (ret < 0) {
+				dev_err(dev, "Counter write error %d\n", ret);
+				goto exit_unlock;
+			}
+		}
+		break;
+
+	case XFLEX_SET_SRC_COUNTER_FPD:
+		reg = flexpm->counterid_fpd;
+		domain = FPM_FPD;
+		ret = kstrtou32(buf, 0, &val);
+		if (ret < 0)
+			goto exit_unlock;
+
+		for (src = 0; src < FPM_NUM_COUNTERS; src++) {
+			reg = reg | FPM_SRC | (src << FPM_PROBE_SHIFT);
+			ret = zynqmp_pm_probe_counter_write(domain, reg, val);
+			if (ret < 0) {
+				dev_err(dev, "Counter write error %d\n", ret);
+				goto exit_unlock;
+			}
+		}
+		break;
+
+	case XFLEX_SET_COUNTER_FPD:
+		ret = kstrtou32(buf, 0, &val);
+		if (ret < 0)
+			goto exit_unlock;
+
+		flexpm->counterid_fpd = val;
+		reset_default(dev, val, FPM_FPD);
+		goto exit_unlock;
+
+	case XFLEX_GET_COUNTER_FPD_WRRSP:
+		reg = flexpm->counterid_fpd | FPM_WRRSP_FPD | FPM_VAL;
+		domain = FPM_FPD;
+
+		break;
+
+	case XFLEX_GET_COUNTER_FPD_WRREQ:
+		reg = flexpm->counterid_fpd | FPM_WRREQ_FPD | FPM_VAL;
+		domain = FPM_FPD;
+
+		break;
+
+	case XFLEX_GET_COUNTER_FPD_RDRSP:
+		reg = flexpm->counterid_fpd | FPM_RDRSP_FPD | FPM_VAL;
+		domain = FPM_FPD;
+
+		break;
+
+	case XFLEX_GET_COUNTER_FPD_RDREQ:
+		reg = flexpm->counterid_fpd | FPM_RDREQ_FPD | FPM_VAL;
+		domain = FPM_FPD;
+
+		break;
+
+	default:
+		dev_err(dev, "Invalid option\n");
+		ret = -EINVAL;
+		goto exit_unlock;
+	}
+
+	ret = zynqmp_pm_probe_counter_read(domain, reg, &pm_api_ret[0]);
+
+	if (ret < 0)
+		dev_err(dev, "Counter read error %d\n", ret);
+	else
+		ret = pm_api_ret[1];
+
+exit_unlock:
+	mutex_unlock(&flexpm->mutex);
+	return ret;
+}
+
+/* Sysfs functions */
+
+static ssize_t counterfpd_wrreq_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_FPD_WRREQ);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterfpd_wrreq);
+
+static ssize_t counterfpd_wrrsp_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_FPD_WRRSP);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterfpd_wrrsp);
+
+static ssize_t counterfpd_rdreq_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_FPD_RDREQ);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterfpd_rdreq);
+
+static ssize_t counterfpd_rdrsp_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_FPD_RDRSP);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterfpd_rdrsp);
+
+static ssize_t counterlpd_wrreq_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_LPD_WRREQ);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterlpd_wrreq);
+
+static ssize_t counterlpd_wrrsp_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_LPD_WRRSP);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterlpd_wrrsp);
+
+static ssize_t counterlpd_rdreq_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_LPD_RDREQ);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterlpd_rdreq);
+
+static ssize_t counterlpd_rdrsp_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	int rdval = xflex_sysfs_cmd(dev, buf, XFLEX_GET_COUNTER_LPD_RDRSP);
+
+	if (rdval < 0)
+		return 0;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rdval);
+}
+static DEVICE_ATTR_RO(counterlpd_rdrsp);
+
+static ssize_t counterlpdsrc_store(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t size)
+{
+	xflex_sysfs_cmd(dev, buf, XFLEX_SET_SRC_COUNTER_LPD);
+
+	return size;
+}
+static DEVICE_ATTR_WO(counterlpdsrc);
+
+static ssize_t counterfpdsrc_store(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t size)
+{
+	xflex_sysfs_cmd(dev, buf, XFLEX_SET_SRC_COUNTER_FPD);
+
+	return size;
+}
+static DEVICE_ATTR_WO(counterfpdsrc);
+
+static ssize_t counterlpdport_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t size)
+{
+	xflex_sysfs_cmd(dev, buf, XFLEX_SET_PORT_COUNTER_LPD);
+
+	return size;
+}
+static DEVICE_ATTR_WO(counterlpdport);
+
+static ssize_t counterfpdport_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t size)
+{
+	xflex_sysfs_cmd(dev, buf, XFLEX_SET_PORT_COUNTER_FPD);
+
+	return size;
+}
+static DEVICE_ATTR_WO(counterfpdport);
+
+static ssize_t counteridlpd_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	struct xflex_dev_info *flexpm = to_xflex_dev_info(dev);
+
+	return snprintf(buf, PAGE_SIZE, "%08d\n", flexpm->counterid_lpd);
+}
+
+static ssize_t counteridlpd_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	int ret;
+	struct xflex_dev_info *flexpm = to_xflex_dev_info(dev);
+
+	ret = kstrtou32(buf, 0, &flexpm->counterid_lpd);
+	if (ret < 0)
+		return ret;
+
+	reset_default(dev, flexpm->counterid_lpd, FPM_LPD);
+
+	return size;
+}
+static DEVICE_ATTR_RW(counteridlpd);
+
+static ssize_t counteridfpd_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	struct xflex_dev_info *flexpm = to_xflex_dev_info(dev);
+
+	return snprintf(buf, PAGE_SIZE, "%08d\n", flexpm->counterid_fpd);
+}
+
+static ssize_t counteridfpd_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	int ret;
+	struct xflex_dev_info *flexpm = to_xflex_dev_info(dev);
+
+	ret = kstrtou32(buf, 0, &flexpm->counterid_fpd);
+	if (ret < 0)
+		return ret;
+
+	return size;
+}
+static DEVICE_ATTR_RW(counteridfpd);
+
+static struct attribute *xflex_attrs[] = {
+	&dev_attr_counterlpdsrc.attr,
+	&dev_attr_counterlpdport.attr,
+	&dev_attr_counterfpdsrc.attr,
+	&dev_attr_counterfpdport.attr,
+
+	&dev_attr_counterlpd_rdreq.attr,
+	&dev_attr_counterlpd_wrreq.attr,
+	&dev_attr_counterlpd_rdrsp.attr,
+	&dev_attr_counterlpd_wrrsp.attr,
+
+	&dev_attr_counterfpd_rdreq.attr,
+	&dev_attr_counterfpd_wrreq.attr,
+	&dev_attr_counterfpd_rdrsp.attr,
+	&dev_attr_counterfpd_wrrsp.attr,
+
+	&dev_attr_counteridlpd.attr,
+	&dev_attr_counteridfpd.attr,
+	NULL,
+};
+
+ATTRIBUTE_GROUPS(xflex);
+
+/**
+ * xflex_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This is the driver probe routine. It does all the memory
+ * allocation and creates sysfs entries for the device.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xflex_probe(struct platform_device *pdev)
+{
+	struct xflex_dev_info *flexpm;
+	struct resource *res;
+	int err;
+	struct device *dev = &pdev->dev;
+
+	flexpm = devm_kzalloc(dev, sizeof(*flexpm), GFP_KERNEL);
+	if (!flexpm)
+		return -ENOMEM;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "baselpd");
+	flexpm->baselpd = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(flexpm->baselpd))
+		return PTR_ERR(flexpm->baselpd);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "basefpd");
+	flexpm->basefpd = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(flexpm->basefpd))
+		return PTR_ERR(flexpm->basefpd);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "funnel");
+	flexpm->funnel = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(flexpm->funnel))
+		return PTR_ERR(flexpm->funnel);
+
+	mutex_init(&flexpm->mutex);
+	writel(FPM_UNLOCK, flexpm->funnel + FPM_LAR_OFFSET);
+	writel(FPM_UNLOCK, flexpm->baselpd + FPM_LAR_OFFSET);
+
+	/* Create sysfs file entries for the device */
+	err = sysfs_create_groups(&dev->kobj, xflex_groups);
+	if (err < 0) {
+		dev_err(dev, "unable to create sysfs entries\n");
+		return err;
+	}
+
+	dev_set_drvdata(dev, flexpm);
+
+	return 0;
+}
+
+/**
+ * xflex_remove - Driver remove function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function frees all the resources allocated to the device.
+ *
+ * Return: 0 always
+ */
+static int xflex_remove(struct platform_device *pdev)
+{
+	sysfs_remove_groups(&pdev->dev.kobj, xflex_groups);
+	return 0;
+}
+
+static const struct of_device_id xflex_of_match[] = {
+	{ .compatible = "xlnx,flexnoc-pm-2.7", },
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xflex_of_match);
+
+static struct platform_driver xflex_driver = {
+	.driver = {
+		.name = "xilinx-flex",
+		.of_match_table = xflex_of_match,
+	},
+	.probe = xflex_probe,
+	.remove = xflex_remove,
+};
+
+module_platform_driver(xflex_driver);
+
+MODULE_AUTHOR("Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx Flexnoc performance monitor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx_tmr_inject.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx_tmr_inject.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for Xilinx TMR Inject IP.
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ *
+ * Description:
+ * This driver is developed for TMR Inject IP,The Triple Modular Redundancy(TMR)
+ * Inject provides fault injection.
+ * Fault injection and detection features are provided through sysfs entries
+ * which allow the user to generate a fault.
+ */
+
+#include <asm/xilinx_mb_manager.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+
+/* TMR Inject Register offsets */
+#define XTMR_INJECT_CR_OFFSET		0x0
+#define XTMR_INJECT_AIR_OFFSET		0x4
+#define XTMR_INJECT_IIR_OFFSET		0xC
+#define XTMR_INJECT_EAIR_OFFSET		0x10
+#define XTMR_INJECT_ERR_OFFSET		0x204
+
+/* Register Bitmasks/shifts */
+#define XTMR_INJECT_CR_CPUID_SHIFT	8
+#define XTMR_INJECT_CR_IE_SHIFT		10
+#define XTMR_INJECT_IIR_ADDR_MASK	GENMASK(31, 16)
+
+/**
+ * struct xtmr_inject_dev - Driver data for TMR Inject
+ * @regs: device physical base address
+ * @dev: pointer to device struct
+ * @cr_val: control register value
+ * @magic: Magic hardware configuration value
+ * @err_cnt: error statistics count
+ */
+struct xtmr_inject_dev {
+	void __iomem *regs;
+	struct device *dev;
+	u32 cr_val;
+	u32 magic;
+	u32 err_cnt;
+};
+
+/* IO accessors */
+static inline void xtmr_inject_write(struct xtmr_inject_dev *xtmr_inject, u32 addr,
+				     u32 value)
+{
+	iowrite32(value, xtmr_inject->regs + addr);
+}
+
+static inline u32 xtmr_inject_read(struct xtmr_inject_dev *xtmr_inject, u32 addr)
+{
+	return ioread32(xtmr_inject->regs + addr);
+}
+
+static ssize_t inject_err_store(struct device *dev,
+				struct device_attribute *attr, const char *buf,
+				size_t size)
+{
+	int ret;
+	long value;
+
+	ret = kstrtol(buf, 16, &value);
+	if (ret)
+		return ret;
+
+	if (value > 1)
+		return -EINVAL;
+
+	xmb_inject_err();
+
+	return size;
+}
+static DEVICE_ATTR_WO(inject_err);
+
+static ssize_t inject_cpuid_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	struct xtmr_inject_dev *xtmr_inject = dev_get_drvdata(dev);
+	int ret;
+	long value;
+
+	ret = kstrtol(buf, 0, &value);
+	if (ret)
+		return ret;
+
+	if (value > 3)
+		return -EINVAL;
+
+	xtmr_inject->cr_val |= (value << XTMR_INJECT_CR_CPUID_SHIFT);
+	xtmr_inject_write(xtmr_inject, XTMR_INJECT_CR_OFFSET,
+			  xtmr_inject->cr_val);
+
+	return size;
+}
+static DEVICE_ATTR_WO(inject_cpuid);
+
+static struct attribute *xtmr_inject_attrs[] = {
+	&dev_attr_inject_err.attr,
+	&dev_attr_inject_cpuid.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(xtmr_inject);
+
+static void xtmr_inject_init(struct xtmr_inject_dev *xtmr_inject)
+{
+	/* Allow fault injection */
+	xtmr_inject->cr_val = xtmr_inject->magic |
+				(1 << XTMR_INJECT_CR_IE_SHIFT) |
+				(1 << XTMR_INJECT_CR_CPUID_SHIFT);
+	xtmr_inject_write(xtmr_inject, XTMR_INJECT_CR_OFFSET,
+			  xtmr_inject->cr_val);
+	/* Initialize the address inject and instruction inject registers */
+	xtmr_inject_write(xtmr_inject, XTMR_INJECT_AIR_OFFSET,
+			  XMB_INJECT_ERR_OFFSET);
+	xtmr_inject_write(xtmr_inject, XTMR_INJECT_IIR_OFFSET,
+			  XMB_INJECT_ERR_OFFSET & XTMR_INJECT_IIR_ADDR_MASK);
+}
+
+/**
+ * xtmr_inject_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This is the driver probe routine. It does all the memory
+ * allocation and creates sysfs entries for the device.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xtmr_inject_probe(struct platform_device *pdev)
+{
+	struct xtmr_inject_dev *xtmr_inject;
+	struct resource *res;
+	int err;
+
+	xtmr_inject = devm_kzalloc(&pdev->dev, sizeof(*xtmr_inject), GFP_KERNEL);
+	if (!xtmr_inject)
+		return -ENOMEM;
+
+	xtmr_inject->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xtmr_inject->regs = devm_ioremap_resource(xtmr_inject->dev, res);
+	if (IS_ERR(xtmr_inject->regs))
+		return PTR_ERR(xtmr_inject->regs);
+
+	err = of_property_read_u32(pdev->dev.of_node, "xlnx,magic",
+				   &xtmr_inject->magic);
+	if (err < 0) {
+		dev_err(&pdev->dev, "unable to read xlnx,magic property");
+		return err;
+	}
+
+	/* Initialize TMR Inject */
+	xtmr_inject_init(xtmr_inject);
+
+	err = sysfs_create_groups(&xtmr_inject->dev->kobj, xtmr_inject_groups);
+	if (err < 0) {
+		dev_err(&pdev->dev, "unable to create sysfs entries\n");
+		return err;
+	}
+
+	platform_set_drvdata(pdev, xtmr_inject);
+
+	return 0;
+}
+
+static int xtmr_inject_remove(struct platform_device *pdev)
+{
+	sysfs_remove_groups(&pdev->dev.kobj, xtmr_inject_groups);
+
+	return 0;
+}
+
+static const struct of_device_id xtmr_inject_of_match[] = {
+	{
+		.compatible = "xlnx,tmr-inject-1.0",
+	},
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xtmr_inject_of_match);
+
+static struct platform_driver xtmr_inject_driver = {
+	.driver = {
+		.name = "xilinx-tmr_inject",
+		.of_match_table = xtmr_inject_of_match,
+	},
+	.probe = xtmr_inject_probe,
+	.remove = xtmr_inject_remove,
+};
+module_platform_driver(xtmr_inject_driver);
+MODULE_AUTHOR("Xilinx, Inc");
+MODULE_DESCRIPTION("Xilinx TMR Inject Driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx_tmr_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx_tmr_manager.c
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx TMR Subsystem.
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ *
+ * Description:
+ * This driver is developed for TMR Manager,The Triple Modular Redundancy(TMR)
+ * Manager is responsible for handling the TMR subsystem state, including
+ * fault detection and error recovery. The core is triplicated in each of
+ * the sub-blocks in the TMR subsystem, and provides majority voting of
+ * its internal state provides soft error detection, correction and
+ * recovery. Error detection feature is provided through sysfs
+ * entries which allow the user to observer the TMR microblaze
+ * status.
+ */
+
+#include <asm/xilinx_mb_manager.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+
+/* TMR Manager Register offsets */
+#define XTMR_MANAGER_CR_OFFSET		0x0
+#define XTMR_MANAGER_FFR_OFFSET		0x4
+#define XTMR_MANAGER_CMR0_OFFSET	0x8
+#define XTMR_MANAGER_CMR1_OFFSET	0xC
+#define XTMR_MANAGER_BDIR_OFFSET	0x10
+#define XTMR_MANAGER_SEMIMR_OFFSET	0x1C
+
+/* Register Bitmasks/shifts */
+#define XTMR_MANAGER_CR_MAGIC1_MASK	0x00ff
+#define XTMR_MANAGER_CR_MAGIC2_MASK	0xff00
+#define XTMR_MANAGER_CR_RIR_MASK	0x10000
+#define XTMR_MANAGER_CR_MAGIC2_SHIFT	4
+#define XTMR_MANAGER_CR_RIR_SHIFT	16
+#define XTMR_MANAGER_CR_BB_SHIFT	18
+
+#define XTMR_MANAGER_FFR_LM12_MASK	BIT(0)
+#define XTMR_MANAGER_FFR_LM13_MASK	BIT(1)
+#define XTMR_MANAGER_FFR_LM23_MASK	BIT(2)
+
+/**
+ * struct xtmr_manager_dev - Driver data for TMR Manager
+ * @regs: device physical base address
+ * @dev: pointer to device struct
+ * @cr_val: control register value
+ * @magic1: Magic 1 hardware configuration value
+ * @err_cnt: error statistics count
+ * @phys_baseaddr: Physical base address
+ */
+struct xtmr_manager_dev {
+	void __iomem *regs;
+	struct device *dev;
+	u32 cr_val;
+	u32 magic1;
+	u32 err_cnt;
+	uintptr_t phys_baseaddr;
+};
+
+/* IO accessors */
+static inline void xtmr_manager_write(struct xtmr_manager_dev *xtmr_manager, u32 addr,
+				      u32 value)
+{
+	iowrite32(value, xtmr_manager->regs + addr);
+}
+
+static inline u32 xtmr_manager_read(struct xtmr_manager_dev *xtmr_manager, u32 addr)
+{
+	return ioread32(xtmr_manager->regs + addr);
+}
+
+/**
+ * xtmr_manager_unblock_break - unblocks the break signal
+ * @xtmr_manager: Pointer to xtmr_manager_dev structure
+ */
+static void xtmr_manager_unblock_break(struct xtmr_manager_dev *xtmr_manager)
+{
+	xtmr_manager->cr_val &= ~(1 << XTMR_MANAGER_CR_BB_SHIFT);
+	xtmr_manager_write(xtmr_manager, XTMR_MANAGER_CR_OFFSET, xtmr_manager->cr_val);
+}
+
+/**
+ * xmb_manager_reset_handler - clears the ffr register contents
+ * @priv: Private pointer
+ */
+static void xmb_manager_reset_handler(void *priv)
+{
+	struct xtmr_manager_dev *xtmr_manager = (struct xtmr_manager_dev *)priv;
+	/*
+	 * Clear the FFR Register contents as a part of recovery process.
+	 */
+	xtmr_manager_write(xtmr_manager, XTMR_MANAGER_FFR_OFFSET, 0);
+}
+
+/**
+ * xmb_manager_update_errcnt - update the error inject count
+ * @priv: Private pointer
+ */
+static void xmb_manager_update_errcnt(void *priv)
+{
+	struct xtmr_manager_dev *xtmr_manager = (struct xtmr_manager_dev *)priv;
+
+	xtmr_manager->err_cnt++;
+}
+
+static ssize_t errcnt_show(struct device *dev, struct device_attribute *attr,
+			   char *buf)
+{
+	struct xtmr_manager_dev *xtmr_manager = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%x\n", xtmr_manager->err_cnt);
+}
+static DEVICE_ATTR_RO(errcnt);
+
+static ssize_t status_show(struct device *dev, struct device_attribute *attr,
+			   char *buf)
+{
+	struct xtmr_manager_dev *xtmr_manager = dev_get_drvdata(dev);
+	size_t ffr;
+	int len = 0;
+
+	ffr = xtmr_manager_read(xtmr_manager, XTMR_MANAGER_FFR_OFFSET);
+	if ((ffr & XTMR_MANAGER_FFR_LM12_MASK) == XTMR_MANAGER_FFR_LM12_MASK) {
+		len += sprintf(buf + len,
+			       "Lockstep mismatch between processor 1 and 2\n");
+	}
+
+	if ((ffr & XTMR_MANAGER_FFR_LM13_MASK) == XTMR_MANAGER_FFR_LM13_MASK) {
+		len += sprintf(buf + len,
+			       "Lockstep mismatch between processor 1 and 3\n");
+	}
+
+	if ((ffr & XTMR_MANAGER_FFR_LM23_MASK) == XTMR_MANAGER_FFR_LM23_MASK) {
+		len += sprintf(buf + len,
+			       "Lockstep mismatch between processor 2 and 3\n");
+	}
+
+	return len;
+}
+static DEVICE_ATTR_RO(status);
+
+static ssize_t dis_block_break_store(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t size)
+{
+	struct xtmr_manager_dev *xtmr_manager = dev_get_drvdata(dev);
+	int ret;
+	long value;
+
+	ret = kstrtol(buf, 16, &value);
+	if (ret)
+		return ret;
+
+	if (value > 1)
+		return -EINVAL;
+
+	xtmr_manager_unblock_break(xtmr_manager);
+	return size;
+}
+static DEVICE_ATTR_WO(dis_block_break);
+
+static struct attribute *xtmr_manager_attrs[] = {
+	&dev_attr_dis_block_break.attr,
+	&dev_attr_status.attr,
+	&dev_attr_errcnt.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(xtmr_manager);
+
+static void xtmr_manager_init(struct xtmr_manager_dev *xtmr_manager)
+{
+	/* Clear the SEM interrupt mask register to disable the interrupt */
+	xtmr_manager_write(xtmr_manager, XTMR_MANAGER_SEMIMR_OFFSET, 0);
+
+	/* Allow recovery reset by default */
+	xtmr_manager->cr_val = (1 << XTMR_MANAGER_CR_RIR_SHIFT) |
+				xtmr_manager->magic1;
+	xtmr_manager_write(xtmr_manager, XTMR_MANAGER_CR_OFFSET,
+			   xtmr_manager->cr_val);
+	/*
+	 * Configure Break Delay Initialization Register to zero so that
+	 * break occurs immediately
+	 */
+	xtmr_manager_write(xtmr_manager, XTMR_MANAGER_BDIR_OFFSET, 0);
+
+	/*
+	 * To come out of break handler need to block the break signal
+	 * in the tmr manager, update the xtmr_manager cr_val for the same
+	 */
+	xtmr_manager->cr_val |= (1 << XTMR_MANAGER_CR_BB_SHIFT);
+
+	/*
+	 * When the break vector gets asserted because of error injection,
+	 * the break signal must be blocked before exiting from the
+	 * break handler, Below api updates the TMR manager address and
+	 * control register and error counter callback arguments,
+	 * which will be used by the break handler to block the
+	 * break and call the callback function.
+	 */
+	xmb_manager_register(xtmr_manager->phys_baseaddr, xtmr_manager->cr_val,
+			     xmb_manager_update_errcnt,
+			     xtmr_manager, xmb_manager_reset_handler);
+}
+
+/**
+ * xtmr_manager_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This is the driver probe routine. It does all the memory
+ * allocation and creates sysfs entries for the device.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xtmr_manager_probe(struct platform_device *pdev)
+{
+	struct xtmr_manager_dev *xtmr_manager;
+	struct resource *res;
+	int err;
+
+	xtmr_manager = devm_kzalloc(&pdev->dev, sizeof(*xtmr_manager), GFP_KERNEL);
+	if (!xtmr_manager)
+		return -ENOMEM;
+
+	xtmr_manager->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xtmr_manager->regs = devm_ioremap_resource(xtmr_manager->dev, res);
+	if (IS_ERR(xtmr_manager->regs))
+		return PTR_ERR(xtmr_manager->regs);
+
+	xtmr_manager->phys_baseaddr = res->start;
+
+	err = of_property_read_u32(pdev->dev.of_node, "xlnx,magic1",
+				   &xtmr_manager->magic1);
+	if (err < 0) {
+		dev_err(&pdev->dev, "unable to read xlnx,magic1 property");
+		return err;
+	}
+
+	/* Initialize TMR Manager */
+	xtmr_manager_init(xtmr_manager);
+
+	err = sysfs_create_groups(&xtmr_manager->dev->kobj,
+				  xtmr_manager_groups);
+	if (err < 0) {
+		dev_err(&pdev->dev, "unable to create sysfs entries\n");
+		return err;
+	}
+
+	platform_set_drvdata(pdev, xtmr_manager);
+
+	return 0;
+}
+
+static int xtmr_manager_remove(struct platform_device *pdev)
+{
+	sysfs_remove_groups(&pdev->dev.kobj, xtmr_manager_groups);
+
+	return 0;
+}
+
+static const struct of_device_id xtmr_manager_of_match[] = {
+	{
+		.compatible = "xlnx,tmr-manager-1.0",
+	},
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xtmr_manager_of_match);
+
+static struct platform_driver xtmr_manager_driver = {
+	.driver = {
+		.name = "xilinx-tmr_manager",
+		.of_match_table = xtmr_manager_of_match,
+	},
+	.probe = xtmr_manager_probe,
+	.remove = xtmr_manager_remove,
+};
+module_platform_driver(xtmr_manager_driver);
+
+MODULE_AUTHOR("Xilinx, Inc");
+MODULE_DESCRIPTION("Xilinx TMR Manager Driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xilinx_trafgen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xilinx_trafgen.c
@@ -0,0 +1,1652 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AXI Traffic Generator driver.
+ *
+ * Copyright (c) 2013 - 2019 Xilinx Inc.
+ *
+ * Description:
+ * This driver is developed for AXI Traffic Generator IP, which is
+ * designed to generate AXI4 traffic which can be used to stress
+ * different modules/interconnect connected in the system. Different
+ * configurable options which are provided through sysfs entries
+ * allow the user to generate a wide variety of traffic based on
+ * their requirements.
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+/* Hw specific definitions */
+
+/* Internal RAM Offsets */
+#define XTG_PARAM_RAM_OFFSET	   0x1000  /* Parameter RAM offset */
+#define XTG_COMMAND_RAM_OFFSET	   0x8000  /* Command RAM offset */
+#define XTG_COMMAND_RAM_MSB_OFFSET 0xa000	/**< Command RAM MSB Offset */
+#define XTG_MASTER_RAM_INIT_OFFSET 0x10000 /* Master RAM initial offset(v1.0) */
+#define XTG_MASTER_RAM_OFFSET	   0xc000  /* Master RAM offset */
+#define XTG_WRITE_COMMAND_RAM_OFFSET	0x9000  /* Write Command RAM offset */
+
+/* Register Offsets */
+#define XTG_MCNTL_OFFSET	0x00	/* Master control */
+#define XTG_SCNTL_OFFSET	0x04	/* Slave control */
+#define XTG_ERR_STS_OFFSET	0x08	/* Error status  */
+#define XTG_ERR_EN_OFFSET	0x0C	/* Error enable */
+#define XTG_MSTERR_INTR_OFFSET	0x10	/* Master error interrupt enable */
+#define XTG_CFG_STS_OFFSET	0x14	/* Config status */
+#define XTG_STREAM_CNTL_OFFSET	0x30	/* Streaming Control */
+#define XTG_STREAM_CFG_OFFSET	0x34	/* Streaming Control */
+#define XTG_STREAM_TL_OFFSET	0x38    /* Streaming Transfer Length */
+#define XTG_STREAM_TKTS1_OFFSET	0x40    /* Streaming tkeep tstrb set1*/
+#define XTG_STREAM_TKTS2_OFFSET	0x44    /* Streaming tkeep tstrb set2*/
+#define XTG_STREAM_TKTS3_OFFSET	0x48    /* Streaming tkeep tstrb set3*/
+#define XTG_STREAM_TKTS4_OFFSET	0x4C    /* Streaming tkeep tstrb set4*/
+#define XTG_STATIC_CNTL_OFFSET	0x60	/* Static Control */
+#define XTG_STATIC_LEN_OFFSET	0x64	/* Static Length */
+
+/* Register Bitmasks/shifts */
+
+/* Master logic enable */
+#define XTG_MCNTL_MSTEN_MASK		0x00100000
+/* Loop enable */
+#define XTG_MCNTL_LOOPEN_MASK		0x00080000
+/* Slave error interrupt enable */
+#define XTG_SCNTL_ERREN_MASK		0x00008000
+/* Master complete interrupt enable */
+#define XTG_ERR_EN_MSTIRQEN_MASK	0x80000000
+/* Master error interrupt enable */
+#define XTG_MSTERR_INTR_MINTREN_MASK	0x00008000
+/* Master complete done status */
+#define XTG_ERR_STS_MSTDONE_MASK	0x80000000
+/* Error mask for error status/enable registers */
+#define XTG_ERR_ALL_ERRS_MASK		0x801F0003
+/* Core Revision shift */
+#define XTG_MCNTL_REV_SHIFT		24
+
+/* Axi Traffic Generator Command RAM Entry field mask/shifts */
+
+/* Command RAM entry masks */
+#define XTG_LEN_MASK		0xFF		/* Driven to a*_len line  */
+#define XTG_LOCK_MASK		0x1		/* Driven to a*_lock line */
+#define XTG_BURST_MASK		0x3		/* Driven to a*_burst line */
+#define XTG_SIZE_MASK		0x7		/* Driven to a*_size line */
+#define XTG_ID_MASK		0x1F		/* Driven to a*_id line */
+#define XTG_PROT_MASK		0x7		/* Driven to a*_prot line */
+#define XTG_LAST_ADDR_MASK	0x7		/* Last address */
+#define XTG_VALID_CMD_MASK	0x1		/* Valid Command */
+#define XTG_MSTRAM_INDEX_MASK	0x1FFF		/* Master RAM Index */
+#define XTG_OTHER_DEPEND_MASK	0x1FF		/* Other depend Command no */
+#define XTG_MY_DEPEND_MASK	0x1FF		/* My depend command no */
+#define XTG_QOS_MASK		0xF		/* Driven to a*_qos line */
+#define XTG_USER_MASK		0xFF		/* Driven to a*_user line */
+#define XTG_CACHE_MASK		0xF		/* Driven to a*_cache line */
+#define XTG_EXPECTED_RESP_MASK	0x7		/* Expected response */
+
+/* Command RAM entry shift values */
+#define XTG_LEN_SHIFT		0		/* Driven to a*_len line  */
+#define XTG_LOCK_SHIFT		8		/* Driven to a*_lock line */
+#define XTG_BURST_SHIFT		10		/* Driven to a*_burst line */
+#define XTG_SIZE_SHIFT		12		/* Driven to a*_size line */
+#define XTG_ID_SHIFT		15		/* Driven to a*_id line */
+#define XTG_PROT_SHIFT		21		/* Driven to a*_prot line */
+#define XTG_LAST_ADDR_SHIFT	28		/* Last address */
+#define XTG_VALID_CMD_SHIFT	31		/* Valid Command */
+#define XTG_MSTRAM_INDEX_SHIFT	0		/* Master RAM Index */
+#define XTG_OTHER_DEPEND_SHIFT	13		/* Other depend cmd num */
+#define XTG_MY_DEPEND_SHIFT	22		/* My depend cmd num */
+#define XTG_QOS_SHIFT		16		/* Driven to a*_qos line */
+#define XTG_USER_SHIFT		5		/* Driven to a*_user line */
+#define XTG_CACHE_SHIFT		4		/* Driven to a*_cache line */
+#define XTG_EXPECTED_RESP_SHIFT	0		/* Expected response */
+
+/* Axi Traffic Generator Parameter RAM Entry field mask/shifts */
+
+/* Parameter RAM Entry field shift values */
+#define XTG_PARAM_ADDRMODE_SHIFT	24	/* Address mode */
+#define XTG_PARAM_INTERVALMODE_SHIFT	26	/* Interval mode */
+#define XTG_PARAM_IDMODE_SHIFT		28	/* Id mode */
+#define XTG_PARAM_OP_SHIFT		29	/* Opcode */
+
+/* PARAM RAM Opcode shift values */
+#define XTG_PARAM_COUNT_SHIFT		0	/* Repeat/Delay count */
+#define XTG_PARAM_DELAYRANGE_SHIFT	0	/* Delay range */
+#define XTG_PARAM_DELAY_SHIFT		8	/* FIXED RPT delay count */
+#define XTG_PARAM_ADDRRANGE_SHIFT	20	/* Address range */
+
+/* Parameter RAM Entry field mask values */
+#define XTG_PARAM_ADDRMODE_MASK		0x3	/* Address mode */
+#define XTG_PARAM_INTERVALMODE_MASK	0x3	/* Interval mode */
+#define XTG_PARAM_IDMODE_MASK		0x1	/* Id mode */
+#define XTG_PARAM_OP_MASK		0x7	/* Opcode */
+
+/* PARAM RAM Opcode mask values */
+#define XTG_PARAM_COUNT_MASK		0xFFFFFF/* Repeat/Delay count */
+#define XTG_PARAM_DELAYRANGE_MASK	0xFF	/* Delay range */
+#define XTG_PARAM_DELAY_MASK		0xFFF	/* FIXED RPT delay count */
+#define XTG_PARAM_ADDRRANGE_MASK	0xF	/* Address range */
+
+/* PARAM RAM Opcode values */
+#define XTG_PARAM_OP_NOP		0x0	/* NOP mode */
+#define XTG_PARAM_OP_RPT		0x1	/* Repeat mode */
+#define XTG_PARAM_OP_DELAY		0x2	/* Delay mode */
+#define XTG_PARAM_OP_FIXEDRPT		0x3	/* Fixed repeat delay */
+
+/* Axi Traffic Generator Static Mode masks */
+#define XTG_STATIC_CNTL_TD_MASK		0x00000002	/* Transfer Done Mask */
+#define XTG_STATIC_CNTL_STEN_MASK	0x00000001	/* Static Enable Mask */
+#define XTG_STATIC_CNTL_RESET_MASK	0x00000000	/* Static Reset Mask */
+
+/* Axi Traffic Generator Stream Mode mask/shifts */
+#define XTG_STREAM_CNTL_STEN_MASK   0x00000001	/* Stream Enable Mask */
+#define XTG_STREAM_TL_TCNT_MASK	    0xFFFF0000	/* Transfer Count Mask */
+#define XTG_STREAM_TL_TLEN_MASK	    0x0000FFFF	/* Transfer Length Mask */
+#define XTG_STREAM_TL_TCNT_SHIFT    16		/* Transfer Count Shift */
+
+/* Driver Specific Definitions */
+
+#define MAX_NUM_ENTRIES	256	/* Number of command entries per region */
+
+#define VALID_SIG	0xa5a5a5a5	/* Valid unique identifier */
+
+/* Internal RAM Sizes */
+#define XTG_PRM_RAM_BLOCK_SIZE	0x400	/* PRAM Block size (1KB) */
+#define XTG_CMD_RAM_BLOCK_SIZE	0x1000	/* CRAM Block size (4KB) */
+#define XTG_EXTCMD_RAM_BLOCK_SIZE 0x400	/**< Extended CMDRAM Block Size (1KB) */
+#define XTG_PARAM_RAM_SIZE	0x800	/* Parameter RAM (2KB) */
+#define XTG_COMMAND_RAM_SIZE	0x2000	/* Command RAM (8KB) */
+#define XTG_EXTCMD_RAM_SIZE	0x800	/* Command RAM (2KB) */
+#define XTG_MASTER_RAM_SIZE	0x2000	/* Master RAM (8KB) */
+
+/* RAM Access Flags */
+#define XTG_READ_RAM		0x0	/* Read RAM flag */
+#define XTG_WRITE_RAM		0x1	/* Write RAM flag */
+#define XTG_WRITE_RAM_ZERO	0x2	/* Write Zero flag */
+
+/* Bytes per entry */
+#define XTG_CRAM_BYTES_PER_ENTRY	16 /* CRAM bytes per entry */
+#define XTG_PRAM_BYTES_PER_ENTRY	4  /* PRAM bytes per entry */
+
+/* Interrupt Definitions */
+#define XTG_MASTER_CMP_INTR	0x1	/* Master complete intr flag */
+#define XTG_MASTER_ERR_INTR	0x2	/* Master error intr flag */
+#define XTG_SLAVE_ERR_INTR	0x4	/* Slave error intr flag */
+
+/*
+ * Version value of the trafgen core.
+ * For the initial IP release the version(v1.0) value is 0x47
+ * From the v2.0 IP and onwards the value starts from  0x20.
+ * For eg:
+ * v2.1 -> 0x21
+ * v2.2 -> 0x22 ... so on.
+ *
+ */
+#define XTG_INIT_VERSION	0x47	/* Trafgen initial version(v1.0) */
+
+/* Macro */
+#define to_xtg_dev_info(n)	((struct xtg_dev_info *)dev_get_drvdata(n))
+
+#define CMD_WDS	0x4	/* No of words in command ram per command */
+#define EXT_WDS	0x1	/* No of words in extended ram per command */
+#define MSB_INDEX	0x4
+/**
+ * struct xtg_cram - Command RAM structure
+ * @addr: Address Driven to a*_addr line
+ * @valid_cmd: Valid Command
+ * @last_addr: Last address
+ * @prot: Driven to a*_prot line
+ * @id: Driven to a*_id line
+ * @size: Driven to a*_size line
+ * @burst: Driven to a*_burst line
+ * @lock: Driven to a*_lock line
+ * @length: Driven to a*_len line
+ * @my_dpnd: My Depend command number
+ * @other_dpnd: Other depend command number
+ * @mram_idx: Master RAM index
+ * @qos: Driven to a*_qos line
+ * @user: Driven to a*_user line
+ * @cache: Driven to a*_cache line
+ * @expected_resp: Expected response
+ * @index: Command Index
+ * @is_write_block: Write/Read block
+ * @is_valid_req: Unique signature
+ *
+ * FIXME: This structure is shared with the user application and
+ * hence need to be synchronized. We know these kind of structures
+ * should not be defined in the driver and this need to be fixed
+ * if found a proper placeholder (in uapi/).
+ */
+struct xtg_cram {
+	phys_addr_t addr;
+	u32 valid_cmd;
+	u32 last_addr;
+	u32 prot;
+	u32 id;
+	u32 size;
+	u32 burst;
+	u32 lock;
+	u32 length;
+	u32 my_dpnd;
+	u32 other_dpnd;
+	u32 mram_idx;
+	u32 qos;
+	u32 user;
+	u32 cache;
+	u32 expected_resp;
+	u16 index;
+	bool is_write_block;
+	u32 is_valid_req;
+};
+
+/**
+ * struct xtg_pram - Parameter RAM structure
+ * @op_cntl0: Control field 0
+ * @op_cntl1: Control field 1
+ * @op_cntl2: Control field 2
+ * @addr_mode: Address mode
+ * @interval_mode: Interval mode
+ * @id_mode: Id mode
+ * @opcode: Opcode
+ * @index: Command Index
+ * @is_write_block: Write/Read block
+ * @is_valid_req: Unique signature
+ *
+ * FIXME: This structure is shared with the user application and
+ * hence need to be synchronized. We know these kind of structures
+ * should not be defined in the driver and this need to be fixed
+ * if found a proper placeholder (in uapi/).
+ */
+struct xtg_pram {
+	u32 op_cntl0;
+	u32 op_cntl1;
+	u32 op_cntl2;
+	u32 addr_mode;
+	u32 interval_mode;
+	u32 id_mode;
+	u32 opcode;
+	u16 index;
+	bool is_write_block;
+	u32 is_valid_req;
+};
+
+/**
+ * struct xtg_dev_info - Global Driver structure
+ * @regs: Iomapped base address
+ * @dev: Device structure
+ * @phys_base_addr: Physical base address
+ * @last_rd_valid_idx: Last Read Valid Command Index
+ * @last_wr_valid_idx: Last Write Valid Command Index
+ * @id: Device instance id
+ * @xtg_mram_offset: MasterRam offset
+ * @clk: Input clock
+ */
+struct xtg_dev_info {
+	void __iomem *regs;
+	struct device *dev;
+	phys_addr_t phys_base_addr;
+	s16 last_rd_valid_idx;
+	s16 last_wr_valid_idx;
+	u32 id;
+	u32 xtg_mram_offset;
+	struct clk *clk;
+};
+
+/**
+ * enum xtg_sysfs_ioctl_opcode - Ioctl opcodes
+ * @XTG_GET_MASTER_CMP_STS: get master complete status
+ * @XTG_GET_SLV_CTRL_REG: get slave control reg status
+ * @XTG_GET_ERR_STS: get error status
+ * @XTG_GET_CFG_STS: get config status
+ * @XTG_GET_LAST_VALID_INDEX: get last valid index
+ * @XTG_GET_DEVICE_ID: get device id
+ * @XTG_GET_RESOURCE: get resource
+ * @XTG_GET_STATIC_ENABLE: get staic mode traffic genration state
+ * @XTG_GET_STATIC_BURSTLEN: get static mode burst length
+ * @XTG_GET_STATIC_TRANSFERDONE: get static transfer done
+ * @XTG_GET_STREAM_ENABLE : get strean mode traffic genration state
+ * @XTG_GET_STREAM_TRANSFERLEN: get streaming mode transfer length
+ * @XTG_GET_STREAM_TRANSFERCNT: get streaming mode transfer count
+ * @XTG_GET_MASTER_LOOP_EN: get master loop enable status
+ * @XTG_GET_STREAM_TKTS1: get stream tstrb and tkeep set1 values
+ * @XTG_GET_STREAM_TKTS2: get stream tstrb and tkeep set2 values
+ * @XTG_GET_STREAM_TKTS3: get stream tstrb and tkeep set3 values
+ * @XTG_GET_STREAM_TKTS4: get stream tstrb and tkeep set4 values
+ * @XTG_GET_STREAM_CFG: get stream configuration values
+ * @XTG_START_MASTER_LOGIC: start master logic
+ * @XTG_SET_SLV_CTRL_REG: set slave control
+ * @XTG_CLEAR_ERRORS: clear errors
+ * @XTG_ENABLE_ERRORS: enable errors
+ * @XTG_ENABLE_INTRS: enable interrupts
+ * @XTG_CLEAR_MRAM: clear master ram
+ * @XTG_CLEAR_CRAM: clear command ram
+ * @XTG_CLEAR_PRAM: clear parameter ram
+ * @XTG_SET_STATIC_ENABLE: enable static mode traffic genration
+ * @XTG_SET_STATIC_DISABLE: disable static mode traffic genration
+ * @XTG_SET_STATIC_BURSTLEN: set static mode burst length
+ * @XTG_SET_STATIC_TRANSFERDONE: set static transfer done
+ * @XTG_SET_STREAM_ENABLE: enable streaming mode traffic genration
+ * @XTG_SET_STREAM_DISABLE: disable streaming mode traffic genration
+ * @XTG_SET_STREAM_TRANSFERLEN: set streaming mode transfer length
+ * @XTG_SET_STREAM_TRANSFERCNT: set streaming mode transfer count
+ * @XTG_SET_STREAM_TKTS1: set stream tstrb and tkeep set1 values
+ * @XTG_SET_STREAM_TKTS2: set stream tstrb and tkeep set2 values
+ * @XTG_SET_STREAM_TKTS3: set stream tstrb and tkeep set3 values
+ * @XTG_SET_STREAM_TKTS4: set stream tstrb and tkeep set4 values
+ * @XTG_SET_STREAM_CFG: set stream configuration values
+ * @XTG_MASTER_LOOP_EN: enable master loop
+ */
+enum xtg_sysfs_ioctl_opcode {
+	XTG_GET_MASTER_CMP_STS,
+	XTG_GET_SLV_CTRL_REG,
+	XTG_GET_ERR_STS,
+	XTG_GET_CFG_STS,
+	XTG_GET_LAST_VALID_INDEX,
+	XTG_GET_DEVICE_ID,
+	XTG_GET_RESOURCE,
+	XTG_GET_STATIC_ENABLE,
+	XTG_GET_STATIC_BURSTLEN,
+	XTG_GET_STATIC_TRANSFERDONE,
+	XTG_GET_STREAM_ENABLE,
+	XTG_GET_STREAM_TRANSFERLEN,
+	XTG_GET_MASTER_LOOP_EN,
+	XTG_GET_STREAM_TKTS1,
+	XTG_GET_STREAM_TKTS2,
+	XTG_GET_STREAM_TKTS3,
+	XTG_GET_STREAM_TKTS4,
+	XTG_GET_STREAM_CFG,
+	XTG_GET_STREAM_TRANSFERCNT,
+	XTG_START_MASTER_LOGIC,
+	XTG_SET_SLV_CTRL_REG,
+	XTG_CLEAR_ERRORS,
+	XTG_ENABLE_ERRORS,
+	XTG_ENABLE_INTRS,
+	XTG_CLEAR_MRAM,
+	XTG_CLEAR_CRAM,
+	XTG_CLEAR_PRAM,
+	XTG_SET_STATIC_ENABLE,
+	XTG_SET_STATIC_DISABLE,
+	XTG_SET_STATIC_BURSTLEN,
+	XTG_SET_STATIC_TRANSFERDONE,
+	XTG_SET_STREAM_ENABLE,
+	XTG_SET_STREAM_DISABLE,
+	XTG_SET_STREAM_TRANSFERLEN,
+	XTG_SET_STREAM_TRANSFERCNT,
+	XTG_SET_STREAM_TKTS1,
+	XTG_SET_STREAM_TKTS2,
+	XTG_SET_STREAM_TKTS3,
+	XTG_SET_STREAM_TKTS4,
+	XTG_SET_STREAM_CFG,
+	XTG_MASTER_LOOP_EN
+};
+
+/**
+ * xtg_access_rams - Write/Read Master/Command/Parameter RAM
+ * @tg: Pointer to xtg_dev_info structure
+ * @where: Offset from base
+ * @count: Number of bytes to write/read
+ * @flags: Read/Write/Write Zero
+ * @data: Data pointer
+ */
+static void xtg_access_rams(struct xtg_dev_info *tg, int where,
+			    int count, int flags, u32 *data)
+{
+	u32 index;
+
+	switch (flags) {
+	case XTG_WRITE_RAM_ZERO:
+		memset_io(tg->regs + where, 0, count);
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+		writel(0x0, tg->regs + where +
+			(XTG_COMMAND_RAM_MSB_OFFSET - XTG_COMMAND_RAM_OFFSET) +
+			XTG_EXTCMD_RAM_BLOCK_SIZE - XTG_CMD_RAM_BLOCK_SIZE);
+#endif
+		break;
+	case XTG_WRITE_RAM:
+		for (index = 0; count > 0; index++, count -= 4)
+			writel(data[index], tg->regs + where + index * 4);
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+	/*
+	 * This additional logic is required only for command ram.
+	 * when writing to READ Command RAM write higher address to READ addr
+	 * RAM
+	 */
+	if (where >= XTG_COMMAND_RAM_OFFSET &&
+	    where < XTG_WRITE_COMMAND_RAM_OFFSET)
+		writel(data[MSB_INDEX],	tg->regs + XTG_COMMAND_RAM_OFFSET +
+			(where - XTG_COMMAND_RAM_OFFSET) / 4 +
+			(XTG_COMMAND_RAM_MSB_OFFSET - XTG_COMMAND_RAM_OFFSET));
+	/*
+	 * Writing to WRITE Command RAM write higher address to WRITE addr RAM
+	 */
+	if (where >=  XTG_WRITE_COMMAND_RAM_OFFSET &&
+	    where < XTG_COMMAND_RAM_MSB_OFFSET)
+		writel(data[MSB_INDEX],	tg->regs +
+			XTG_WRITE_COMMAND_RAM_OFFSET +
+			(where - XTG_WRITE_COMMAND_RAM_OFFSET) / 4 +
+			(XTG_COMMAND_RAM_MSB_OFFSET - XTG_COMMAND_RAM_OFFSET) +
+			XTG_EXTCMD_RAM_BLOCK_SIZE - XTG_CMD_RAM_BLOCK_SIZE);
+#endif
+		break;
+	case XTG_READ_RAM:
+		for (index = 0; count > 0; index++, count -= 4)
+			data[index] = readl(tg->regs + where + index * 4);
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (where >= XTG_COMMAND_RAM_OFFSET &&
+	    where < XTG_WRITE_COMMAND_RAM_OFFSET)
+		data[MSB_INDEX] = readl(tg->regs + XTG_COMMAND_RAM_OFFSET +
+			(where - XTG_COMMAND_RAM_OFFSET) / 4 +
+			(XTG_COMMAND_RAM_MSB_OFFSET - XTG_COMMAND_RAM_OFFSET));
+
+	if (where >=  XTG_WRITE_COMMAND_RAM_OFFSET &&
+	    where < XTG_COMMAND_RAM_MSB_OFFSET)
+		data[MSB_INDEX] = readl(tg->regs +
+			XTG_WRITE_COMMAND_RAM_OFFSET +
+			(where - XTG_WRITE_COMMAND_RAM_OFFSET) / 4 +
+			(XTG_COMMAND_RAM_MSB_OFFSET - XTG_COMMAND_RAM_OFFSET) +
+			XTG_EXTCMD_RAM_BLOCK_SIZE - XTG_CMD_RAM_BLOCK_SIZE);
+#endif
+		break;
+	}
+}
+
+/**
+ * xtg_prepare_cmd_words - Prepares all four Command RAM words
+ * @tg: Pointer to xtg_dev_info structure
+ * @cmdp: Pointer to xtg_cram structure
+ * @cmd_words: Pointer to Command Words that needs to be prepared
+ */
+static void xtg_prepare_cmd_words(struct xtg_dev_info *tg,
+				  const struct xtg_cram *cmdp, u32 *cmd_words)
+{
+	/* Command Word 0 */
+	cmd_words[0] = lower_32_bits(cmdp->addr);
+
+	/* Command Word 4 */
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+	cmd_words[MSB_INDEX] = upper_32_bits(cmdp->addr);
+#endif
+
+	/* Command Word 1 */
+	cmd_words[1] = 0;
+	cmd_words[1] |= (cmdp->length & XTG_LEN_MASK) << XTG_LEN_SHIFT;
+	cmd_words[1] |= (cmdp->lock & XTG_LOCK_MASK) << XTG_LOCK_SHIFT;
+	cmd_words[1] |= (cmdp->burst & XTG_BURST_MASK) << XTG_BURST_SHIFT;
+	cmd_words[1] |= (cmdp->size & XTG_SIZE_MASK) << XTG_SIZE_SHIFT;
+	cmd_words[1] |= (cmdp->id & XTG_ID_MASK) << XTG_ID_SHIFT;
+	cmd_words[1] |= (cmdp->prot & XTG_PROT_MASK) << XTG_PROT_SHIFT;
+	cmd_words[1] |= (cmdp->last_addr & XTG_LAST_ADDR_MASK) <<
+					XTG_LAST_ADDR_SHIFT;
+	cmd_words[1] |= (cmdp->valid_cmd & XTG_VALID_CMD_MASK) <<
+					XTG_VALID_CMD_SHIFT;
+
+	/* Command Word 2 */
+	cmd_words[2] = 0;
+	cmd_words[2] |= (cmdp->mram_idx & XTG_MSTRAM_INDEX_MASK) <<
+					XTG_MSTRAM_INDEX_SHIFT;
+	cmd_words[2] |= (cmdp->other_dpnd & XTG_OTHER_DEPEND_MASK) <<
+					XTG_OTHER_DEPEND_SHIFT;
+	cmd_words[2] |= (cmdp->my_dpnd & XTG_MY_DEPEND_MASK) <<
+					XTG_MY_DEPEND_SHIFT;
+
+	/* Command Word 3 */
+	cmd_words[3] = 0;
+	cmd_words[3] |= (cmdp->qos & XTG_QOS_MASK) << XTG_QOS_SHIFT;
+	cmd_words[3] |= (cmdp->user & XTG_USER_MASK) << XTG_USER_SHIFT;
+	cmd_words[3] |= (cmdp->cache & XTG_CACHE_MASK) << XTG_CACHE_SHIFT;
+	cmd_words[3] |= (cmdp->expected_resp & XTG_EXPECTED_RESP_MASK) <<
+					XTG_EXPECTED_RESP_SHIFT;
+}
+
+/**
+ * xtg_prepare_param_word - Prepares Parameter RAM word
+ * @tg: Pointer to xtg_dev_info structure
+ * @cmdp: Pointer to xtg_pram structure
+ * @param_word: Pointer to Param Word that needs to be prepared
+ */
+static void xtg_prepare_param_word(struct xtg_dev_info *tg,
+				   const struct xtg_pram *cmdp, u32 *param_word)
+{
+	*param_word = 0;
+	*param_word |= (cmdp->opcode & XTG_PARAM_OP_MASK) << XTG_PARAM_OP_SHIFT;
+	*param_word |= (cmdp->addr_mode & XTG_PARAM_ADDRMODE_MASK) <<
+					XTG_PARAM_ADDRMODE_SHIFT;
+	*param_word |= (cmdp->id_mode & XTG_PARAM_IDMODE_MASK) <<
+					XTG_PARAM_IDMODE_SHIFT;
+	*param_word |= (cmdp->interval_mode & XTG_PARAM_INTERVALMODE_MASK) <<
+					XTG_PARAM_INTERVALMODE_SHIFT;
+
+	switch (cmdp->opcode) {
+	case XTG_PARAM_OP_RPT:
+	case XTG_PARAM_OP_DELAY:
+		*param_word |= (cmdp->op_cntl0 & XTG_PARAM_COUNT_MASK) <<
+					XTG_PARAM_COUNT_SHIFT;
+		break;
+
+	case XTG_PARAM_OP_FIXEDRPT:
+		*param_word |= (cmdp->op_cntl0 & XTG_PARAM_ADDRRANGE_MASK) <<
+					XTG_PARAM_ADDRRANGE_SHIFT;
+		*param_word |= (cmdp->op_cntl1 & XTG_PARAM_DELAY_MASK) <<
+					XTG_PARAM_DELAY_SHIFT;
+		*param_word |= (cmdp->op_cntl2 & XTG_PARAM_DELAYRANGE_MASK) <<
+					XTG_PARAM_DELAYRANGE_SHIFT;
+		break;
+
+	case XTG_PARAM_OP_NOP:
+		*param_word = 0;
+		break;
+	}
+}
+
+/**
+ * xtg_sysfs_ioctl - Implements sysfs operations
+ * @dev: Device structure
+ * @buf: Value to write
+ * @opcode: Ioctl opcode
+ *
+ * Return: value read from the sysfs opcode.
+ */
+static ssize_t xtg_sysfs_ioctl(struct device *dev, const char *buf,
+			       enum xtg_sysfs_ioctl_opcode opcode)
+{
+	struct xtg_dev_info *tg = to_xtg_dev_info(dev);
+	unsigned long wrval;
+	ssize_t status, rdval = 0;
+
+	if (opcode > XTG_GET_STREAM_TRANSFERCNT) {
+		status = kstrtoul(buf, 0, &wrval);
+		if (status < 0)
+			return status;
+	}
+
+	switch (opcode) {
+	case XTG_GET_MASTER_CMP_STS:
+		rdval = (readl(tg->regs + XTG_MCNTL_OFFSET) &
+				XTG_MCNTL_MSTEN_MASK) ? 1 : 0;
+		break;
+
+	case XTG_GET_MASTER_LOOP_EN:
+		rdval = (readl(tg->regs + XTG_MCNTL_OFFSET) &
+				XTG_MCNTL_LOOPEN_MASK) ? 1 : 0;
+		break;
+
+	case XTG_GET_SLV_CTRL_REG:
+		rdval = readl(tg->regs + XTG_SCNTL_OFFSET);
+		break;
+
+	case XTG_GET_ERR_STS:
+		rdval = readl(tg->regs + XTG_ERR_STS_OFFSET) &
+				XTG_ERR_ALL_ERRS_MASK;
+		break;
+
+	case XTG_GET_CFG_STS:
+		rdval = readl(tg->regs + XTG_CFG_STS_OFFSET);
+		break;
+
+	case XTG_GET_LAST_VALID_INDEX:
+		rdval = (((tg->last_wr_valid_idx << 16) & 0xffff0000) |
+				(tg->last_rd_valid_idx & 0xffff));
+		break;
+
+	case XTG_GET_DEVICE_ID:
+		rdval = tg->id;
+		break;
+
+	case XTG_GET_RESOURCE:
+		rdval = (unsigned long)tg->regs;
+		break;
+
+	case XTG_GET_STATIC_ENABLE:
+		rdval = readl(tg->regs + XTG_STATIC_CNTL_OFFSET);
+		break;
+
+	case XTG_GET_STATIC_BURSTLEN:
+		rdval = readl(tg->regs + XTG_STATIC_LEN_OFFSET);
+		break;
+
+	case XTG_GET_STATIC_TRANSFERDONE:
+		rdval = (readl(tg->regs + XTG_STATIC_CNTL_OFFSET) &
+				XTG_STATIC_CNTL_TD_MASK);
+		break;
+
+	case XTG_GET_STREAM_ENABLE:
+		rdval = readl(tg->regs + XTG_STREAM_CNTL_OFFSET);
+		break;
+
+	case XTG_GET_STREAM_TRANSFERLEN:
+		rdval = (readl(tg->regs + XTG_STREAM_TL_OFFSET) &
+				XTG_STREAM_TL_TLEN_MASK);
+		break;
+
+	case XTG_GET_STREAM_TRANSFERCNT:
+		rdval = ((readl(tg->regs + XTG_STREAM_TL_OFFSET) &
+				XTG_STREAM_TL_TCNT_MASK) >>
+				XTG_STREAM_TL_TCNT_SHIFT);
+		break;
+
+	case XTG_GET_STREAM_TKTS1:
+		rdval = readl(tg->regs + XTG_STREAM_TKTS1_OFFSET);
+		break;
+	case XTG_GET_STREAM_TKTS2:
+		rdval = readl(tg->regs + XTG_STREAM_TKTS2_OFFSET);
+		break;
+	case XTG_GET_STREAM_TKTS3:
+		rdval = readl(tg->regs + XTG_STREAM_TKTS3_OFFSET);
+		break;
+	case XTG_GET_STREAM_TKTS4:
+		rdval = readl(tg->regs + XTG_STREAM_TKTS4_OFFSET);
+		break;
+
+	case XTG_GET_STREAM_CFG:
+		rdval = (readl(tg->regs + XTG_STREAM_CFG_OFFSET));
+		break;
+
+	case XTG_START_MASTER_LOGIC:
+		if (wrval)
+			writel(readl(tg->regs + XTG_MCNTL_OFFSET) |
+					XTG_MCNTL_MSTEN_MASK,
+				tg->regs + XTG_MCNTL_OFFSET);
+		break;
+
+	case XTG_MASTER_LOOP_EN:
+		if (wrval)
+			writel(readl(tg->regs + XTG_MCNTL_OFFSET) |
+					XTG_MCNTL_LOOPEN_MASK,
+				tg->regs + XTG_MCNTL_OFFSET);
+		else
+			writel(readl(tg->regs + XTG_MCNTL_OFFSET) &
+					~XTG_MCNTL_LOOPEN_MASK,
+				tg->regs + XTG_MCNTL_OFFSET);
+		break;
+
+	case XTG_SET_SLV_CTRL_REG:
+		writel(wrval, tg->regs + XTG_SCNTL_OFFSET);
+		break;
+
+	case XTG_ENABLE_ERRORS:
+		wrval &= XTG_ERR_ALL_ERRS_MASK;
+		writel(wrval, tg->regs + XTG_ERR_EN_OFFSET);
+		break;
+
+	case XTG_CLEAR_ERRORS:
+		wrval &= XTG_ERR_ALL_ERRS_MASK;
+		writel(readl(tg->regs + XTG_ERR_STS_OFFSET) | wrval,
+		       tg->regs + XTG_ERR_STS_OFFSET);
+		break;
+
+	case XTG_ENABLE_INTRS:
+		if (wrval & XTG_MASTER_CMP_INTR) {
+			pr_info("Enabling Master Complete Interrupt\n");
+			writel(readl(tg->regs + XTG_ERR_EN_OFFSET) |
+					XTG_ERR_EN_MSTIRQEN_MASK,
+				tg->regs + XTG_ERR_EN_OFFSET);
+		}
+		if (wrval & XTG_MASTER_ERR_INTR) {
+			pr_info("Enabling Interrupt on Master Errors\n");
+			writel(readl(tg->regs + XTG_MSTERR_INTR_OFFSET) |
+					XTG_MSTERR_INTR_MINTREN_MASK,
+				tg->regs + XTG_MSTERR_INTR_OFFSET);
+		}
+		if (wrval & XTG_SLAVE_ERR_INTR) {
+			pr_info("Enabling Interrupt on Slave Errors\n");
+			writel(readl(tg->regs + XTG_SCNTL_OFFSET) |
+					XTG_SCNTL_ERREN_MASK,
+				tg->regs + XTG_SCNTL_OFFSET);
+		}
+		break;
+
+	case XTG_CLEAR_MRAM:
+		xtg_access_rams(tg, tg->xtg_mram_offset,
+				XTG_MASTER_RAM_SIZE,
+				XTG_WRITE_RAM_ZERO, NULL);
+		break;
+
+	case XTG_CLEAR_CRAM:
+		xtg_access_rams(tg, XTG_COMMAND_RAM_OFFSET,
+				XTG_COMMAND_RAM_SIZE,
+				XTG_WRITE_RAM_ZERO, NULL);
+		break;
+
+	case XTG_CLEAR_PRAM:
+		xtg_access_rams(tg, XTG_PARAM_RAM_OFFSET,
+				XTG_PARAM_RAM_SIZE,
+				XTG_WRITE_RAM_ZERO, NULL);
+		break;
+
+	case XTG_SET_STATIC_ENABLE:
+		if (wrval) {
+			wrval &= XTG_STATIC_CNTL_STEN_MASK;
+			writel(readl(tg->regs + XTG_STATIC_CNTL_OFFSET) | wrval,
+			       tg->regs + XTG_STATIC_CNTL_OFFSET);
+		} else {
+			writel(readl(tg->regs + XTG_STATIC_CNTL_OFFSET) &
+				~XTG_STATIC_CNTL_STEN_MASK,
+				tg->regs + XTG_STATIC_CNTL_OFFSET);
+		}
+		break;
+
+	case XTG_SET_STATIC_BURSTLEN:
+		writel(wrval, tg->regs + XTG_STATIC_LEN_OFFSET);
+		break;
+
+	case XTG_SET_STATIC_TRANSFERDONE:
+		wrval |= XTG_STATIC_CNTL_TD_MASK;
+		writel(readl(tg->regs + XTG_STATIC_CNTL_OFFSET) | wrval,
+		       tg->regs + XTG_STATIC_CNTL_OFFSET);
+		break;
+
+	case XTG_SET_STREAM_ENABLE:
+		if (wrval) {
+			rdval = readl(tg->regs + XTG_STREAM_CNTL_OFFSET);
+			rdval |= XTG_STREAM_CNTL_STEN_MASK;
+			writel(rdval,
+			       tg->regs + XTG_STREAM_CNTL_OFFSET);
+		} else {
+			writel(readl(tg->regs + XTG_STREAM_CNTL_OFFSET) &
+			       ~XTG_STREAM_CNTL_STEN_MASK,
+			       tg->regs + XTG_STREAM_CNTL_OFFSET);
+		}
+		break;
+
+	case XTG_SET_STREAM_TRANSFERLEN:
+		wrval &= XTG_STREAM_TL_TLEN_MASK;
+		rdval = readl(tg->regs + XTG_STREAM_TL_OFFSET);
+		rdval &= ~XTG_STREAM_TL_TLEN_MASK;
+		writel(rdval | wrval,
+		       tg->regs + XTG_STREAM_TL_OFFSET);
+		break;
+
+	case XTG_SET_STREAM_TRANSFERCNT:
+		wrval = ((wrval << XTG_STREAM_TL_TCNT_SHIFT) &
+				XTG_STREAM_TL_TCNT_MASK);
+		rdval = readl(tg->regs + XTG_STREAM_TL_OFFSET);
+		rdval = rdval & ~XTG_STREAM_TL_TCNT_MASK;
+		writel(rdval | wrval,
+		       tg->regs + XTG_STREAM_TL_OFFSET);
+		break;
+
+	case XTG_SET_STREAM_TKTS1:
+		writel(wrval, tg->regs + XTG_STREAM_TKTS1_OFFSET);
+		break;
+	case XTG_SET_STREAM_TKTS2:
+		writel(wrval, tg->regs + XTG_STREAM_TKTS2_OFFSET);
+		break;
+	case XTG_SET_STREAM_TKTS3:
+		writel(wrval, tg->regs + XTG_STREAM_TKTS3_OFFSET);
+		break;
+	case XTG_SET_STREAM_TKTS4:
+		writel(wrval, tg->regs + XTG_STREAM_TKTS4_OFFSET);
+		break;
+
+	case XTG_SET_STREAM_CFG:
+		writel(wrval, tg->regs + XTG_STREAM_CFG_OFFSET);
+		break;
+
+	default:
+		break;
+	}
+
+	return rdval;
+}
+
+/* Sysfs functions */
+
+static ssize_t id_show(struct device *dev,
+		       struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_DEVICE_ID);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+static DEVICE_ATTR_RO(id);
+
+static ssize_t resource_show(struct device *dev,
+			     struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_RESOURCE);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+static DEVICE_ATTR_RO(resource);
+
+static ssize_t master_start_stop_show(struct device *dev,
+				      struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_MASTER_CMP_STS);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t master_start_stop_store(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_START_MASTER_LOGIC);
+
+	return size;
+}
+static DEVICE_ATTR_RW(master_start_stop);
+
+static ssize_t config_slave_status_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_SLV_CTRL_REG);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+
+static ssize_t config_slave_status_store(struct device *dev,
+					 struct device_attribute *attr,
+					 const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_SLV_CTRL_REG);
+
+	return size;
+}
+static DEVICE_ATTR_RW(config_slave_status);
+
+static ssize_t err_sts_show(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_ERR_STS);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+
+static ssize_t err_sts_store(struct device *dev,
+			     struct device_attribute *attr,
+			     const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_CLEAR_ERRORS);
+
+	return size;
+}
+static DEVICE_ATTR_RW(err_sts);
+
+static ssize_t err_en_store(struct device *dev,
+			    struct device_attribute *attr, const char *buf,
+			    size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_ENABLE_ERRORS);
+
+	return size;
+}
+static DEVICE_ATTR_WO(err_en);
+
+static ssize_t intr_en_store(struct device *dev,
+			     struct device_attribute *attr,
+			     const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_ENABLE_INTRS);
+
+	return size;
+}
+static DEVICE_ATTR_WO(intr_en);
+
+static ssize_t last_valid_index_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_LAST_VALID_INDEX);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+static DEVICE_ATTR_RO(last_valid_index);
+
+static ssize_t config_sts_show(struct device *dev,
+			       struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_CFG_STS);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+static DEVICE_ATTR_RO(config_sts);
+
+static ssize_t mram_clear_store(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_CLEAR_MRAM);
+
+	return size;
+}
+static DEVICE_ATTR_WO(mram_clear);
+
+static ssize_t cram_clear_store(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_CLEAR_CRAM);
+
+	return size;
+}
+static DEVICE_ATTR_WO(cram_clear);
+
+static ssize_t pram_clear_store(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_CLEAR_CRAM);
+
+	return size;
+}
+static DEVICE_ATTR_WO(pram_clear);
+
+static ssize_t static_enable_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STATIC_ENABLE);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+
+static ssize_t static_enable_store(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STATIC_ENABLE);
+
+	return size;
+}
+static DEVICE_ATTR_RW(static_enable);
+
+static ssize_t static_burstlen_show(struct device *dev,
+				    struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STATIC_BURSTLEN);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t static_burstlen_store(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STATIC_BURSTLEN);
+
+	return size;
+}
+static DEVICE_ATTR_RW(static_burstlen);
+
+static ssize_t stream_cfg_show(struct device *dev,
+			       struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_CFG);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_cfg_store(struct device *dev,
+				struct device_attribute *attr, const char *buf,
+				size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_CFG);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_cfg);
+
+static ssize_t stream_tkts4_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_TKTS4);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_tkts4_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_TKTS4);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_tkts4);
+
+static ssize_t stream_tkts3_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_TKTS3);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_tkts3_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_TKTS3);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_tkts3);
+
+static ssize_t stream_tkts2_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_TKTS2);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_tkts2_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_TKTS2);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_tkts2);
+
+static ssize_t stream_tkts1_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_TKTS1);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_tkts1_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_TKTS1);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_tkts1);
+
+static ssize_t static_transferdone_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STATIC_TRANSFERDONE);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t static_transferdone_store(struct device *dev,
+					 struct device_attribute *attr,
+					 const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STATIC_TRANSFERDONE);
+
+	return size;
+}
+static DEVICE_ATTR_RW(static_transferdone);
+
+static ssize_t reset_static_transferdone_show(struct device *dev,
+					      struct device_attribute *attr,
+					      char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STATIC_TRANSFERDONE);
+
+	if (rdval == XTG_STATIC_CNTL_RESET_MASK)
+		rdval = 1;
+	else
+		rdval = 0;
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+static DEVICE_ATTR_RO(reset_static_transferdone);
+
+static ssize_t stream_enable_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_ENABLE);
+
+	return snprintf(buf, PAGE_SIZE, "0x%08zx\n", rdval);
+}
+
+static ssize_t stream_enable_store(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_ENABLE);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_enable);
+
+static ssize_t stream_transferlen_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_TRANSFERLEN);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_transferlen_store(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_TRANSFERLEN);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_transferlen);
+
+static ssize_t stream_transfercnt_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_STREAM_TRANSFERCNT);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t stream_transfercnt_store(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_SET_STREAM_TRANSFERCNT);
+
+	return size;
+}
+static DEVICE_ATTR_RW(stream_transfercnt);
+
+static ssize_t loop_enable_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	ssize_t rdval = xtg_sysfs_ioctl(dev, buf, XTG_GET_MASTER_LOOP_EN);
+
+	return snprintf(buf, PAGE_SIZE, "%zd\n", rdval);
+}
+
+static ssize_t loop_enable_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t size)
+{
+	xtg_sysfs_ioctl(dev, buf, XTG_MASTER_LOOP_EN);
+
+	return size;
+}
+static DEVICE_ATTR_RW(loop_enable);
+
+static ssize_t xtg_pram_read(struct file *filp, struct kobject *kobj,
+			     struct bin_attribute *bin_attr,
+			     char *buf, loff_t off, size_t count)
+{
+	pr_info("No read access to Parameter RAM\n");
+
+	return 0;
+}
+
+static ssize_t xtg_pram_write(struct file *filp, struct kobject *kobj,
+			      struct bin_attribute *bin_attr,
+			      char *buf, loff_t off, size_t count)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+	u32 *data = (u32 *)buf;
+	struct xtg_pram *cmdp = (struct xtg_pram *)buf;
+	u32 param_word;
+
+	if (off >= XTG_PARAM_RAM_SIZE) {
+		pr_err("Requested Write len exceeds 2K PRAM size\n");
+		return -ENOMEM;
+	}
+
+	if (count >= XTG_PARAM_RAM_SIZE)
+		count = XTG_PARAM_RAM_SIZE;
+
+	/* Program each command */
+	if (count == sizeof(struct xtg_pram)) {
+		if (!cmdp)
+			return -EINVAL;
+
+		if (cmdp->is_valid_req == VALID_SIG) {
+			/* Prepare parameter word */
+			xtg_prepare_param_word(tg, cmdp, &param_word);
+
+			count = XTG_PRAM_BYTES_PER_ENTRY;
+			data = &param_word;
+
+			/* Maximum command entries are 256 */
+			if (cmdp->index > MAX_NUM_ENTRIES)
+				return -EINVAL;
+
+			/* Calculate the block index */
+			if (cmdp->is_write_block)
+				off = XTG_PRM_RAM_BLOCK_SIZE +
+						cmdp->index * count;
+			else
+				off = cmdp->index * count;
+		}
+	}
+
+	off += XTG_PARAM_RAM_OFFSET;
+	xtg_access_rams(tg, off, count, XTG_WRITE_RAM, data);
+
+	return count;
+}
+
+static int xtg_pram_mmap(struct file *filp, struct kobject *kobj,
+			 struct bin_attribute *attr,
+			 struct vm_area_struct *vma)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+	int ret;
+
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	vma->vm_flags |= VM_IO;
+
+	ret = remap_pfn_range(vma, vma->vm_start, (tg->phys_base_addr +
+			XTG_PARAM_RAM_OFFSET) >> PAGE_SHIFT,
+			XTG_PARAM_RAM_SIZE, vma->vm_page_prot);
+	return ret;
+}
+
+static struct bin_attribute xtg_pram_attr = {
+	.attr =	{
+		.name = "parameter_ram",
+		.mode = 0644,
+	},
+	.size = XTG_PARAM_RAM_SIZE,
+	.read = xtg_pram_read,
+	.write = xtg_pram_write,
+	.mmap = xtg_pram_mmap,
+};
+
+static ssize_t xtg_cram_read(struct file *filp, struct kobject *kobj,
+			     struct bin_attribute *bin_attr,
+			     char *buf, loff_t off, size_t count)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+
+	off += XTG_COMMAND_RAM_OFFSET;
+	xtg_access_rams(tg, off, count, XTG_READ_RAM, (u32 *)buf);
+
+	return count;
+}
+
+static ssize_t xtg_cram_write(struct file *filp, struct kobject *kobj,
+			      struct bin_attribute *bin_attr,
+			      char *buf, loff_t off, size_t count)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+	u32 *data = (u32 *)buf;
+	struct xtg_cram *cmdp = (struct xtg_cram *)buf;
+	u32 cmd_words[CMD_WDS + EXT_WDS];
+
+	if (off >= XTG_COMMAND_RAM_SIZE) {
+		pr_err("Requested Write len exceeds 8K CRAM size\n");
+		return -ENOMEM;
+	}
+
+	/* Program each command */
+	if (count == sizeof(struct xtg_cram)) {
+		if (!cmdp)
+			return -EINVAL;
+
+		if (cmdp->is_valid_req == VALID_SIG) {
+			/* Prepare command words */
+			xtg_prepare_cmd_words(tg, cmdp, cmd_words);
+			count = XTG_CRAM_BYTES_PER_ENTRY;
+			data = cmd_words;
+
+			/* Maximum command entries are 256 */
+			if (cmdp->index > MAX_NUM_ENTRIES)
+				return -EINVAL;
+
+			/* Calculate the block index */
+			if (cmdp->is_write_block)
+				off = XTG_CMD_RAM_BLOCK_SIZE +
+						cmdp->index * count;
+			else
+				off = cmdp->index * count;
+
+			/* Store the valid command index */
+			if (cmdp->valid_cmd) {
+				if (cmdp->is_write_block)
+					tg->last_wr_valid_idx =
+							cmdp->index;
+				else
+					tg->last_rd_valid_idx =
+							cmdp->index;
+			}
+		}
+	}
+
+	off += XTG_COMMAND_RAM_OFFSET;
+	xtg_access_rams(tg, off, count, XTG_WRITE_RAM, data);
+
+	return count;
+}
+
+static int xtg_cram_mmap(struct file *filp, struct kobject *kobj,
+			 struct bin_attribute *attr,
+			 struct vm_area_struct *vma)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+	int ret;
+
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	vma->vm_flags |= VM_IO;
+
+	ret = remap_pfn_range(vma, vma->vm_start, (tg->phys_base_addr +
+			XTG_COMMAND_RAM_OFFSET) >> PAGE_SHIFT,
+			XTG_COMMAND_RAM_SIZE + XTG_EXTCMD_RAM_SIZE,
+			vma->vm_page_prot);
+	return ret;
+}
+
+static struct bin_attribute xtg_cram_attr = {
+	.attr =	{
+		.name = "command_ram",
+		.mode = 0644,
+	},
+	.size = XTG_COMMAND_RAM_SIZE,
+	.read = xtg_cram_read,
+	.write = xtg_cram_write,
+	.mmap = xtg_cram_mmap,
+};
+
+static ssize_t xtg_mram_read(struct file *filp, struct kobject *kobj,
+			     struct bin_attribute *bin_attr,
+			     char *buf, loff_t off, size_t count)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+
+	off += tg->xtg_mram_offset;
+	xtg_access_rams(tg, off, count, XTG_READ_RAM, (u32 *)buf);
+
+	return count;
+}
+
+static ssize_t xtg_mram_write(struct file *filp, struct kobject *kobj,
+			      struct bin_attribute *bin_attr,
+			      char *buf, loff_t off, size_t count)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+
+	if (off >= XTG_MASTER_RAM_SIZE) {
+		pr_err("Requested Write len exceeds 8K MRAM size\n");
+		return -ENOMEM;
+	}
+
+	off += tg->xtg_mram_offset;
+	xtg_access_rams(tg, off, count, XTG_WRITE_RAM, (u32 *)buf);
+
+	return count;
+}
+
+static int xtg_mram_mmap(struct file *filp, struct kobject *kobj,
+			 struct bin_attribute *attr,
+			 struct vm_area_struct *vma)
+{
+	struct xtg_dev_info *tg =
+		to_xtg_dev_info(container_of(kobj, struct device, kobj));
+	int ret;
+
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	vma->vm_flags |= VM_IO;
+
+	ret = remap_pfn_range(vma, vma->vm_start, (tg->phys_base_addr +
+			tg->xtg_mram_offset) >> PAGE_SHIFT,
+			XTG_MASTER_RAM_SIZE,
+			vma->vm_page_prot);
+	return ret;
+}
+
+static struct bin_attribute xtg_mram_attr = {
+	.attr =	{
+		.name = "master_ram",
+		.mode = 0644,
+	},
+	.size = XTG_MASTER_RAM_SIZE,
+	.read = xtg_mram_read,
+	.write = xtg_mram_write,
+	.mmap = xtg_mram_mmap,
+};
+
+static struct bin_attribute *xtg_bin_attrs[] = {
+	&xtg_mram_attr,
+	&xtg_pram_attr,
+	&xtg_cram_attr,
+	NULL,
+};
+
+static const struct attribute *xtg_attrs[] = {
+	&dev_attr_id.attr,
+	&dev_attr_resource.attr,
+	&dev_attr_master_start_stop.attr,
+	&dev_attr_config_slave_status.attr,
+	&dev_attr_err_en.attr,
+	&dev_attr_err_sts.attr,
+	&dev_attr_intr_en.attr,
+	&dev_attr_last_valid_index.attr,
+	&dev_attr_config_sts.attr,
+	&dev_attr_mram_clear.attr,
+	&dev_attr_cram_clear.attr,
+	&dev_attr_pram_clear.attr,
+	&dev_attr_static_enable.attr,
+	&dev_attr_static_burstlen.attr,
+	&dev_attr_static_transferdone.attr,
+	&dev_attr_stream_transfercnt.attr,
+	&dev_attr_stream_transferlen.attr,
+	&dev_attr_stream_tkts1.attr,
+	&dev_attr_stream_tkts2.attr,
+	&dev_attr_stream_tkts3.attr,
+	&dev_attr_stream_tkts4.attr,
+	&dev_attr_stream_cfg.attr,
+	&dev_attr_stream_enable.attr,
+	&dev_attr_reset_static_transferdone.attr,
+	&dev_attr_loop_enable.attr,
+	NULL,
+};
+
+static const struct attribute_group xtg_attributes = {
+	.attrs = (struct attribute **)xtg_attrs,
+	.bin_attrs = xtg_bin_attrs,
+};
+
+/**
+ * xtg_cmp_intr_handler - Master Complete Interrupt handler
+ * @irq: IRQ number
+ * @data: Pointer to the xtg_dev_info structure
+ *
+ * Return: IRQ_HANDLED always
+ */
+static irqreturn_t xtg_cmp_intr_handler(int irq, void *data)
+{
+	struct xtg_dev_info *tg = (struct xtg_dev_info *)data;
+
+	writel(readl(tg->regs + XTG_ERR_STS_OFFSET) |
+	       XTG_ERR_STS_MSTDONE_MASK, tg->regs + XTG_ERR_STS_OFFSET);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xtg_err_intr_handler - Master/Slave Error Interrupt handler
+ * @irq: IRQ number
+ * @data: Pointer to the xtg_dev_info structure
+ *
+ * Return: IRQ_HANDLED always
+ */
+static irqreturn_t xtg_err_intr_handler(int irq, void *data)
+{
+	struct xtg_dev_info *tg = (struct xtg_dev_info *)data;
+	u32 value;
+
+	value = readl(tg->regs + XTG_ERR_STS_OFFSET) &
+		      XTG_ERR_ALL_ERRS_MASK;
+
+	if (value) {
+		dev_err(tg->dev, "Found errors 0x%08x\n", value);
+		writel(readl(tg->regs + XTG_ERR_STS_OFFSET) | value,
+		       tg->regs + XTG_ERR_STS_OFFSET);
+	}
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xtg_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This is the driver probe routine. It does all the memory
+ * allocation and creates sysfs entries for the device.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int xtg_probe(struct platform_device *pdev)
+{
+	struct xtg_dev_info *tg;
+	struct device_node *node;
+	struct resource *res;
+	struct device *dev;
+	int err, irq, var;
+
+	tg = devm_kzalloc(&pdev->dev, sizeof(*tg), GFP_KERNEL);
+	if (!tg)
+		return -ENOMEM;
+
+	tg->dev = &pdev->dev;
+	dev = tg->dev;
+	node = pdev->dev.of_node;
+
+	/* Map the registers */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	tg->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(tg->regs))
+		return PTR_ERR(tg->regs);
+
+	/* Save physical base address */
+	tg->phys_base_addr = res->start;
+
+	/* Get the device instance id */
+	err = of_property_read_u32(node, "xlnx,device-id", &tg->id);
+	if (err < 0) {
+		dev_err(&pdev->dev, "unable to read property");
+		return err;
+	}
+
+	/* Map the error interrupt, if it exists in the device tree. */
+	irq = platform_get_irq_byname(pdev, "err-out");
+	if (irq < 0) {
+		dev_dbg(&pdev->dev, "unable to get err irq");
+	} else {
+		err = devm_request_irq(&pdev->dev, irq, xtg_err_intr_handler,
+				       0, dev_name(&pdev->dev), tg);
+		if (err < 0) {
+			dev_err(&pdev->dev, "unable to request irq %d", irq);
+			return err;
+		}
+	}
+
+	/* Map the completion interrupt, if it exists in the device tree. */
+	irq = platform_get_irq_byname(pdev, "irq-out");
+	if (irq < 0) {
+		dev_dbg(&pdev->dev, "unable to get cmp irq");
+	} else {
+		err = devm_request_irq(&pdev->dev, irq, xtg_cmp_intr_handler,
+				       0, dev_name(&pdev->dev), tg);
+		if (err < 0) {
+			dev_err(&pdev->dev, "unable to request irq %d", irq);
+			return err;
+		}
+	}
+
+	tg->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(tg->clk)) {
+		if (PTR_ERR(tg->clk) != -ENOENT) {
+			if (PTR_ERR(tg->clk) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "input clock not found\n");
+			return PTR_ERR(tg->clk);
+		}
+		tg->clk = NULL;
+	}
+
+	err = clk_prepare_enable(tg->clk);
+	if (err) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return err;
+	}
+
+	/*
+	 * Create sysfs file entries for the device
+	 */
+	err = sysfs_create_group(&dev->kobj, &xtg_attributes);
+	if (err < 0) {
+		dev_err(tg->dev, "unable to create sysfs entries\n");
+		clk_disable_unprepare(tg->clk);
+		return err;
+	}
+
+	/*
+	 * Initialize the write and read valid index values.
+	 * Possible range of values for these variables is <0 255>.
+	 */
+	tg->last_wr_valid_idx = -1;
+	tg->last_rd_valid_idx = -1;
+
+	dev_set_drvdata(&pdev->dev, tg);
+
+	/* Update the Proper MasterRam offset */
+	tg->xtg_mram_offset = XTG_MASTER_RAM_OFFSET;
+	var = readl(tg->regs + XTG_MCNTL_OFFSET) >> XTG_MCNTL_REV_SHIFT;
+	if (var == XTG_INIT_VERSION)
+		tg->xtg_mram_offset = XTG_MASTER_RAM_INIT_OFFSET;
+
+	dev_info(&pdev->dev, "Probing xilinx traffic generator success\n");
+
+	return 0;
+}
+
+/**
+ * xtg_remove - Driver remove function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function frees all the resources allocated to the device.
+ *
+ * Return: 0 always
+ */
+static int xtg_remove(struct platform_device *pdev)
+{
+	struct xtg_dev_info *tg;
+	struct device *dev;
+
+	tg = dev_get_drvdata(&pdev->dev);
+	dev = tg->dev;
+	sysfs_remove_group(&dev->kobj, &xtg_attributes);
+	clk_disable_unprepare(tg->clk);
+
+	return 0;
+}
+
+static const struct of_device_id xtg_of_match[] = {
+	{ .compatible = "xlnx,axi-traffic-gen", },
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, xtg_of_match);
+
+static struct platform_driver xtg_driver = {
+	.driver = {
+		.name = "xilinx-trafgen",
+		.of_match_table = xtg_of_match,
+	},
+	.probe = xtg_probe,
+	.remove = xtg_remove,
+};
+
+module_platform_driver(xtg_driver);
+
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("Xilinx Traffic Generator driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xlnx_dpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xlnx_dpu.c
@@ -0,0 +1,1211 @@
+// SPDX-License-Identifier: GPL-2.0 OR Apache-2.0
+/*
+ * Xilinx Vivado Flow Deep learning Processing Unit (DPU) Driver
+ *
+ * Copyright (C) 2022 Xilinx, Inc. All rights reserved.
+ *
+ * Authors:
+ *    Ye Yang <ye.yang@xilinx.com>
+ *
+ * This file is dual-licensed; you may select either the GNU General Public
+ * License version 2 or Apache License, Version 2.0.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/miscdevice.h>
+#include <linux/interrupt.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/iopoll.h>
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/nospec.h>
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+#endif
+#include "xlnx_dpu.h"
+
+#define DEVICE_NAME "dpu"
+#define DRV_NAME "xlnx-dpu"
+#define DRIVER_DESC "Xilinx Deep Learning Processing Unit driver"
+
+static int timeout = 5;
+module_param(timeout, int, 0644);
+MODULE_PARM_DESC(timeout, "Set DPU timeout val in secs (default 5s)");
+
+static bool force_poll;
+/*
+ * this parameter is intended to be used only at probe time as there is
+ * no way to disable interrupts from DPU at run time.
+ */
+module_param(force_poll, bool, 0444);
+MODULE_PARM_DESC(force_poll, "polling or interrupt mode (default interrupt)");
+
+/**
+ * struct cu - Computer Unit (cu) structure
+ * @mutex: protects from simultaneous access
+ * @done: completion of cu
+ * @irq: indicates cu IRQ number
+ */
+struct cu {
+	struct mutex	mutex; /* protects from simultaneous accesses */
+	struct completion	done;
+	int	irq;
+};
+
+/**
+ * struct xdpu_dev - Driver data for DPU
+ * @dev: pointer to device struct
+ * @regs: virtual base address for the dpu regmap
+ * @head: indicates dma memory pool list
+ * @cu: indicates computer unit struct
+ * @axi_clk: AXI Lite clock
+ * @dpu_clk: DPU clock used for DPUCZDX8G general logic
+ * @dsp_clk: DSP clock used for DSP blocks
+ * @miscdev: misc device handle
+ * @root: debugfs dentry
+ * @dpu_cnt: indicates how many dpu core/cu enabled in IP, up to 4
+ * @sfm_cnt: indicates softmax core enabled or not
+ */
+struct xdpu_dev {
+	struct device	*dev;
+	void __iomem	*regs;
+	struct list_head	head;
+	struct cu	cu[MAX_CU_NUM];
+	struct clk	*axi_clk;
+	struct clk	*dpu_clk;
+	struct clk	*dsp_clk;
+	struct miscdevice	miscdev;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry	*root;
+#endif
+	u8	dpu_cnt;
+	u8	sfm_cnt;
+};
+
+/**
+ * struct dpu_buffer_block - DPU buffer block
+ * @head: list head
+ * @vaddr: virtual address of the blocks memory
+ * @dma_addr: dma address of the blocks memory
+ * @capacity: total size of the block in bytes
+ */
+struct dpu_buffer_block {
+	struct list_head	head;
+	void	*vaddr;
+	dma_addr_t	dma_addr;
+	size_t	capacity;
+};
+
+#ifdef CONFIG_DEBUG_FS
+static int dpu_debugfs_init(struct xdpu_dev *xdpu);
+#endif
+
+/**
+ * xlnx_dpu_regs_init - initialize dpu register
+ * @xdpu:	dpu structure
+ */
+static void xlnx_dpu_regs_init(struct xdpu_dev *xdpu)
+{
+	int cu;
+
+	iowrite32(0, xdpu->regs + DPU_PMU_IP_RST);
+
+	for (cu = 0; cu < xdpu->dpu_cnt; cu++) {
+		iowrite32(DPU_HPBUS_VAL, xdpu->regs + DPU_HPBUS(cu));
+		iowrite32(0, xdpu->regs + DPU_IPSTART(cu));
+	}
+
+	iowrite32(DPU_RST_ALL_CORES, xdpu->regs + DPU_PMU_IP_RST);
+	iowrite32(0, xdpu->regs + DPU_SFM_RESET);
+	iowrite32(1, xdpu->regs + DPU_SFM_RESET);
+}
+
+/**
+ * xlnx_dpu_dump_regs - dump all dpu registers
+ * @p:	dpu structure
+ */
+static void xlnx_dpu_dump_regs(struct xdpu_dev *p)
+{
+	struct device *dev = p->dev;
+	int i;
+
+#define FMT8	"%-27s %08x\n"
+#define FMT16	"%-27s %016llx\n"
+	dev_warn(dev, "------------[ cut here ]------------\n");
+	dev_warn(dev, "Dump DPU Registers:\n");
+	dev_info(dev, FMT16, "TARGET_ID",
+		 lo_hi_readq(p->regs + DPU_TARGETID_L));
+	dev_info(dev, FMT8, "PMU_RST", ioread32(p->regs + DPU_PMU_IP_RST));
+	dev_info(dev, FMT8, "IP_VER_INFO", ioread32(p->regs + DPU_IPVER_INFO));
+	dev_info(dev, FMT8, "IP_FREQENCY", ioread32(p->regs + DPU_IPFREQENCY));
+	dev_info(dev, FMT8, "INT_STS", ioread32(p->regs + DPU_INT_STS));
+	dev_info(dev, FMT8, "INT_MSK", ioread32(p->regs + DPU_INT_MSK));
+	dev_info(dev, FMT8, "INT_RAW", ioread32(p->regs + DPU_INT_RAW));
+	dev_info(dev, FMT8, "INT_ICR", ioread32(p->regs + DPU_INT_ICR));
+	for (i = 0; i < p->dpu_cnt; i++) {
+		dev_warn(dev, "[CU-%d]\n", i);
+		dev_info(dev, FMT8, "HPBUS", ioread32(p->regs + DPU_HPBUS(i)));
+		dev_info(dev, FMT8, "INSTR",
+			 ioread32(p->regs + DPU_INSADDR(i)));
+		dev_info(dev, FMT8, "START",
+			 ioread32(p->regs + DPU_IPSTART(i)));
+		dev_info(dev, FMT16, "ADDR0",
+			 lo_hi_readq(p->regs + DPU_ADDR0_L(i)));
+		dev_info(dev, FMT16, "ADDR1",
+			 lo_hi_readq(p->regs + DPU_ADDR1_L(i)));
+		dev_info(dev, FMT16, "ADDR2",
+			 lo_hi_readq(p->regs + DPU_ADDR2_L(i)));
+		dev_info(dev, FMT16, "ADDR3",
+			 lo_hi_readq(p->regs + DPU_ADDR3_L(i)));
+		dev_info(dev, FMT16, "ADDR4",
+			 lo_hi_readq(p->regs + DPU_ADDR4_L(i)));
+		dev_info(dev, FMT16, "ADDR5",
+			 lo_hi_readq(p->regs + DPU_ADDR5_L(i)));
+		dev_info(dev, FMT16, "ADDR6",
+			 lo_hi_readq(p->regs + DPU_ADDR6_L(i)));
+		dev_info(dev, FMT16, "ADDR7",
+			 lo_hi_readq(p->regs + DPU_ADDR7_L(i)));
+		dev_info(dev, FMT8, "PSTART",
+			 ioread32(p->regs + DPU_P_STA_C(i)));
+		dev_info(dev, FMT8, "PEND",
+			 ioread32(p->regs + DPU_P_END_C(i)));
+		dev_info(dev, FMT8, "CSTART",
+			 ioread32(p->regs + DPU_C_STA_C(i)));
+		dev_info(dev, FMT8, "CEND",
+			 ioread32(p->regs + DPU_C_END_C(i)));
+		dev_info(dev, FMT8, "SSTART",
+			 ioread32(p->regs + DPU_S_STA_C(i)));
+		dev_info(dev, FMT8, "SEND",
+			 ioread32(p->regs + DPU_S_END_C(i)));
+		dev_info(dev, FMT8, "LSTART",
+			 ioread32(p->regs + DPU_L_STA_C(i)));
+		dev_info(dev, FMT8, "LEND",
+			 ioread32(p->regs + DPU_L_END_C(i)));
+		dev_info(dev, FMT16, "CYCLE",
+			 lo_hi_readq(p->regs + DPU_CYCLE_L(i)));
+		dev_info(dev, FMT8, "AXI", ioread32(p->regs + DPU_AXI_STS(i)));
+	}
+	dev_warn(dev, "[SOFTMAX]\n");
+	if (p->sfm_cnt) {
+#define DUMPREG(r) \
+	dev_info(dev, FMT8, #r, ioread32(p->regs + DPU_SFM_##r))
+		DUMPREG(INT_DONE);
+		DUMPREG(CMD_XLEN);
+		DUMPREG(CMD_YLEN);
+		DUMPREG(SRC_ADDR);
+		DUMPREG(DST_ADDR);
+		DUMPREG(CMD_SCAL);
+		DUMPREG(CMD_OFF);
+		DUMPREG(INT_CLR);
+		DUMPREG(START);
+		DUMPREG(RESET);
+#undef DUMPREG
+	}
+	dev_warn(dev, "------------[ cut here ]------------\n");
+}
+
+/**
+ * xlnx_dpu_int_clear - clean DPU interrupt
+ * @xdpu:	dpu structure
+ * @id:	indicates which cu needs to be clean interrupt
+ */
+static void xlnx_dpu_int_clear(struct xdpu_dev *xdpu, int id)
+{
+	iowrite32(BIT(id), xdpu->regs + DPU_INT_ICR);
+	iowrite32(0, xdpu->regs + DPU_IPSTART(id));
+
+	/* make sure have enough time to receive the INT level */
+	udelay(1);
+
+	iowrite32(ioread32(xdpu->regs + DPU_INT_ICR) & ~BIT(id),
+		  xdpu->regs + DPU_INT_ICR);
+}
+
+/**
+ * xlnx_sfm_int_clear - clean softmax interrupt
+ * @xdpu:	dpu structure
+ */
+static void xlnx_sfm_int_clear(struct xdpu_dev *xdpu)
+{
+	iowrite32(1, xdpu->regs + DPU_SFM_INT_CLR);
+	iowrite32(0, xdpu->regs + DPU_SFM_INT_CLR);
+}
+
+/**
+ * xlnx_dpu_softmax - softmax calculation acceleration using softmax IP
+ * @xdpu:	dpu structure
+ * @p :	softmax pmeter structure
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static int xlnx_dpu_softmax(struct xdpu_dev *xdpu, struct ioc_softmax_t *p)
+{
+	int ret = -ETIMEDOUT;
+	int val;
+
+	iowrite32(p->width, xdpu->regs + DPU_SFM_CMD_XLEN);
+	iowrite32(p->height, xdpu->regs + DPU_SFM_CMD_YLEN);
+
+	/* ip limition - softmax supports up to 32-bit addressing */
+	iowrite32(p->input, xdpu->regs + DPU_SFM_SRC_ADDR);
+	iowrite32(p->output, xdpu->regs + DPU_SFM_DST_ADDR);
+	iowrite32(p->scale, xdpu->regs + DPU_SFM_CMD_SCAL);
+	iowrite32(p->offset, xdpu->regs + DPU_SFM_CMD_OFF);
+	iowrite32(1, xdpu->regs + DPU_SFM_RESET);
+	iowrite32(0, xdpu->regs + DPU_SFM_MODE);
+
+	iowrite32(1, xdpu->regs + DPU_SFM_START);
+	iowrite32(0, xdpu->regs + DPU_SFM_START);
+
+	if (!force_poll) {
+		if (!wait_for_completion_timeout(&xdpu->cu[xdpu->dpu_cnt].done,
+						 TIMEOUT))
+			goto err_out;
+	} else {
+		ret = readx_poll_timeout(ioread32,
+					 xdpu->regs + DPU_SFM_INT_DONE,
+					 val,
+					 val & 0x1,
+					 POLL_PERIOD_US,
+					 TIMEOUT_US);
+		if (ret < 0)
+			goto err_out;
+
+		xlnx_sfm_int_clear(xdpu);
+	}
+
+	dev_dbg(xdpu->dev, "%s: PID=%d CPU=%d\n",
+		__func__, current->pid, raw_smp_processor_id());
+
+	return 0;
+
+err_out:
+	dev_warn(xdpu->dev, "timeout waiting for softmax\n");
+	xlnx_dpu_dump_regs(xdpu);
+
+	return ret;
+}
+
+/**
+ * xlnx_dpu_run - run dpu
+ * @xdpu:	dpu structure
+ * @p:	dpu run struct, contains the necessary address info
+ * @id:	indicates which cu is running
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static int xlnx_dpu_run(struct xdpu_dev *xdpu, struct ioc_kernel_run_t *p,
+			int id)
+{
+	int val, ret;
+
+	iowrite32(p->addr_code >> DPU_INSTR_OFFSET,
+		  xdpu->regs + DPU_INSADDR(id));
+
+	/*
+	 * Addr0: bias/weights
+	 * Addr1: the inter-layer workspacce
+	 * Addr2: the 1st input layer
+	 * Addr3: the output layer
+	 * AddrX: ULLONG_MAX as default
+	 */
+	lo_hi_writeq(p->addr0, xdpu->regs + DPU_ADDR0_L(id));
+	lo_hi_writeq(p->addr1, xdpu->regs + DPU_ADDR1_L(id));
+	lo_hi_writeq(p->addr2, xdpu->regs + DPU_ADDR2_L(id));
+	lo_hi_writeq(p->addr3, xdpu->regs + DPU_ADDR3_L(id));
+
+	if (p->addr4 != ULLONG_MAX)
+		lo_hi_writeq(p->addr4, xdpu->regs + DPU_ADDR4_L(id));
+	if (p->addr5 != ULLONG_MAX)
+		lo_hi_writeq(p->addr5, xdpu->regs + DPU_ADDR5_L(id));
+	if (p->addr6 != ULLONG_MAX)
+		lo_hi_writeq(p->addr6, xdpu->regs + DPU_ADDR6_L(id));
+	if (p->addr7 != ULLONG_MAX)
+		lo_hi_writeq(p->addr7, xdpu->regs + DPU_ADDR7_L(id));
+
+	iowrite32(1, xdpu->regs + DPU_IPSTART(id));
+
+	p->time_start = ktime_get();
+
+	if (!force_poll) {
+		if (!wait_for_completion_timeout(&xdpu->cu[id].done,
+						 TIMEOUT))
+			goto err_out;
+	} else {
+		ret = readx_poll_timeout(ioread32,
+					 xdpu->regs + DPU_INT_RAW,
+					 val,
+					 val & BIT(id),
+					 POLL_PERIOD_US,
+					 TIMEOUT_US);
+		if (ret < 0)
+			goto err_out;
+
+		xlnx_dpu_int_clear(xdpu, id);
+	}
+
+	p->time_end = ktime_get();
+	p->core_id = id;
+	p->pend_cnt = ioread32(xdpu->regs + DPU_P_END_C(id));
+	p->cend_cnt = ioread32(xdpu->regs + DPU_C_END_C(id));
+	p->send_cnt = ioread32(xdpu->regs + DPU_S_END_C(id));
+	p->lend_cnt = ioread32(xdpu->regs + DPU_L_END_C(id));
+	p->pstart_cnt = ioread32(xdpu->regs + DPU_P_STA_C(id));
+	p->cstart_cnt = ioread32(xdpu->regs + DPU_C_STA_C(id));
+	p->sstart_cnt = ioread32(xdpu->regs + DPU_S_STA_C(id));
+	p->lstart_cnt = ioread32(xdpu->regs + DPU_L_STA_C(id));
+	p->counter = lo_hi_readq(xdpu->regs + DPU_CYCLE_L(id));
+
+	dev_dbg(xdpu->dev,
+		"%s: PID=%d DPU=%d CPU=%d TIME=%lldms complete!\n",
+		__func__, current->pid, id, raw_smp_processor_id(),
+		ktime_ms_delta(p->time_end, p->time_start));
+
+	return 0;
+
+err_out:
+	dev_warn(xdpu->dev, "cu[%d] timeout", id);
+	xlnx_dpu_dump_regs(xdpu);
+
+	return -ETIMEDOUT;
+}
+
+/**
+ * xlnx_dpu_alloc_bo - alloc contiguous physical memory for dpu
+ * @xdpu:	dpu structure
+ * @req:	dpcma_req_alloc struct, contains the request info
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static long xlnx_dpu_alloc_bo(struct xdpu_dev *xdpu,
+			      struct dpcma_req_alloc __user *req)
+{
+	struct dpu_buffer_block *pb;
+	size_t size;
+
+	pb = kzalloc(sizeof(*pb), GFP_KERNEL);
+	if (!pb)
+		return -ENOMEM;
+
+	if (get_user(size, &req->size))
+		goto err_pb;
+
+	if (size > SIZE_MAX - PAGE_SIZE)
+		goto err_pb;
+
+	pb->capacity = PAGE_ALIGN(size);
+
+	if (put_user(pb->capacity, &req->capacity))
+		goto err_pb;
+
+	pb->vaddr = dma_alloc_coherent(xdpu->dev, pb->capacity, &pb->dma_addr,
+				       GFP_KERNEL);
+	if (!pb->vaddr)
+		goto err_pb;
+
+	if (put_user(pb->dma_addr, &req->phy_addr))
+		goto err_out;
+
+	list_add(&pb->head, &xdpu->head);
+
+	return 0;
+
+err_out:
+	dma_free_coherent(xdpu->dev, pb->capacity, pb->vaddr, pb->dma_addr);
+err_pb:
+	kfree(pb);
+	return -EFAULT;
+}
+
+/**
+ * xlnx_dpu_free_bo - free contiguous physical memory allocated
+ * @xdpu:	dpu structure
+ * @req:	dpcma_req_free struct, contains the request info
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static long xlnx_dpu_free_bo(struct xdpu_dev *xdpu,
+			     struct dpcma_req_free __user *req)
+{
+	struct list_head *pos = NULL, *next = NULL;
+	u64 phy_addr = 0;
+	struct dpu_buffer_block *h;
+
+	if (get_user(phy_addr, &req->phy_addr))
+		return -EFAULT;
+
+	list_for_each_safe(pos, next, &xdpu->head) {
+		h = list_entry(pos, struct dpu_buffer_block, head);
+		if (phy_addr == h->dma_addr) {
+			dma_free_coherent(xdpu->dev, h->capacity, h->vaddr,
+					  h->dma_addr);
+			list_del(pos);
+			kfree(h);
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dpu_sync_bo - flush/invalidate cache for allocated memory
+ * @xdpu:	dpu structure
+ * @req:	dpcma_req_sync struct, contains the request info
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static long xlnx_dpu_sync_bo(struct xdpu_dev *xdpu,
+			     struct dpcma_req_sync __user *req)
+{
+	struct list_head *pos = NULL;
+	long phy_addr;
+	int dir;
+	size_t size, offset;
+	struct dpu_buffer_block *h;
+
+	if (get_user(phy_addr, &req->phy_addr) ||
+	    get_user(size, &req->size) || get_user(dir, &req->direction))
+		return -EFAULT;
+
+	if (dir != DPU_TO_CPU && dir != CPU_TO_DPU) {
+		dev_err(xdpu->dev, "invalid direction. direction = %d\n", dir);
+		return -EINVAL;
+	}
+
+	list_for_each(pos, &xdpu->head) {
+		h = list_entry(pos, struct dpu_buffer_block, head);
+		if (phy_addr >= h->dma_addr &&
+		    phy_addr < h->dma_addr + h->capacity) {
+			offset = phy_addr;
+			if (dir == DPU_TO_CPU)
+				dma_sync_single_for_cpu(xdpu->dev,
+							offset,
+							size,
+							DMA_FROM_DEVICE);
+			else
+				dma_sync_single_for_device(xdpu->dev,
+							   offset,
+							   size,
+							   DMA_TO_DEVICE);
+		}
+	}
+	return 0;
+}
+
+/**
+ * xlnx_dpu_ioctl - control ioctls for the DPU
+ * @file:	file handle of the DPU device
+ * @cmd:	ioctl code
+ * @arg:	pointer to user passed structure
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static long xlnx_dpu_ioctl(struct file *file, unsigned int cmd,
+			   unsigned long arg)
+{
+	int ret = 0;
+	struct xdpu_dev *xdpu;
+	void __user *data = NULL;
+
+	xdpu = container_of(file->private_data, struct xdpu_dev, miscdev);
+
+	if (_IOC_TYPE(cmd) != DPU_IOC_MAGIC)
+		return -ENOTTY;
+
+	/* check if ioctl argument is present and valid */
+	if (_IOC_DIR(cmd) != _IOC_NONE) {
+		data = (void __user *)arg;
+		if (!data)
+			return -EINVAL;
+	}
+
+	switch (cmd) {
+	case DPUIOC_RUN:
+	{
+		struct ioc_kernel_run_t t;
+		int id;
+
+		if (copy_from_user(&t, data,
+				   sizeof(struct ioc_kernel_run_t))) {
+			return -EINVAL;
+		}
+
+		id = t.core_id;
+		if (id >= xdpu->dpu_cnt)
+			return -EINVAL;
+
+		dev_dbg(xdpu->dev,
+			"%s: PID=%d DPU=%d CPU=%d Comm=%.20s waiting",
+			__func__, current->pid, id, raw_smp_processor_id(),
+			current->comm);
+
+		id = array_index_nospec(id, xdpu->dpu_cnt);
+		/* Allows one process to run the cu by using a mutex */
+		mutex_lock(&xdpu->cu[id].mutex);
+
+		ret = xlnx_dpu_run(xdpu, &t, id);
+
+		mutex_unlock(&xdpu->cu[id].mutex);
+
+		if (copy_to_user(data, &t, sizeof(struct ioc_kernel_run_t)))
+			return -EINVAL;
+
+		break;
+	}
+	case DPUIOC_CREATE_BO:
+		return xlnx_dpu_alloc_bo(xdpu,
+					 (struct dpcma_req_alloc __user *)arg);
+	case DPUIOC_FREE_BO:
+		return xlnx_dpu_free_bo(xdpu,
+					(struct dpcma_req_free __user *)arg);
+	case DPUIOC_SYNC_BO:
+		return xlnx_dpu_sync_bo(xdpu,
+					(struct dpcma_req_sync __user *)arg);
+	case DPUIOC_G_INFO:
+	{
+		u32 dpu_info = ioread32(xdpu->regs + DPU_IPVER_INFO);
+
+		if (copy_to_user(data, &dpu_info, sizeof(dpu_info)))
+			return -EFAULT;
+		break;
+	}
+	case DPUIOC_G_TGTID:
+	{
+		u64 fingerprint = lo_hi_readq(xdpu->regs + DPU_TARGETID_L);
+
+		if (copy_to_user(data, &fingerprint, sizeof(fingerprint)))
+			return -EFAULT;
+		break;
+	}
+	case DPUIOC_RUN_SOFTMAX:
+	{
+		struct ioc_softmax_t t;
+
+		if (copy_from_user(&t, data,
+				   sizeof(struct ioc_softmax_t))) {
+			dev_err(xdpu->dev, "copy_from_user softmax_t fail\n");
+			return -EINVAL;
+		}
+
+		mutex_lock(&xdpu->cu[xdpu->dpu_cnt].mutex);
+
+		ret = xlnx_dpu_softmax(xdpu, &t);
+
+		mutex_unlock(&xdpu->cu[xdpu->dpu_cnt].mutex);
+
+		break;
+	}
+	case DPUIOC_REG_READ:
+	{
+		u32 val = 0;
+		u32 off = 0;
+
+		if (copy_from_user(&off, data, sizeof(off))) {
+			dev_err(xdpu->dev, "copy_from_user off failed\n");
+			return -EINVAL;
+		}
+
+		val = ioread32(xdpu->regs + off);
+
+		if (copy_to_user(data, &val, sizeof(val)))
+			return -EFAULT;
+		break;
+	}
+	default:
+		ret = -EOPNOTSUPP;
+	}
+
+	return ret;
+}
+
+/**
+ * xlnx_dpu_isr - interrupt handler for DPU.
+ * @irq:	Interrupt number.
+ * @data:	DPU device structure.
+ *
+ * Return: IRQ_HANDLED.
+ */
+static irqreturn_t xlnx_dpu_isr(int irq, void *data)
+{
+	struct xdpu_dev *xdpu = data;
+	int i;
+
+	for (i = 0; i < xdpu->dpu_cnt; i++) {
+		if (irq == xdpu->cu[i].irq) {
+			xlnx_dpu_int_clear(xdpu, i);
+			dev_dbg(xdpu->dev, "%s: DPU=%d IRQ=%d",
+				__func__, i, irq);
+			complete(&xdpu->cu[i].done);
+		}
+	}
+
+	if (irq == xdpu->cu[xdpu->dpu_cnt].irq) {
+		xlnx_sfm_int_clear(xdpu);
+		dev_dbg(xdpu->dev, "%s: softmax IRQ=%d", __func__, irq);
+		complete(&xdpu->cu[xdpu->dpu_cnt].done);
+	}
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xlnx_dpu_mmap - maps cma ranges into userspace
+ * @file:	file structure for the device
+ * @vma:	VMA to map the registers into
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static int xlnx_dpu_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	size_t size = vma->vm_end - vma->vm_start;
+	phys_addr_t offset = (phys_addr_t)vma->vm_pgoff << PAGE_SHIFT;
+
+	if ((offset >> PAGE_SHIFT) != vma->vm_pgoff)
+		return -EINVAL;
+
+	if ((offset + (phys_addr_t)size - 1) < offset)
+		return -EINVAL;
+
+	if (!((vma->vm_pgoff + size) <= __pa(high_memory)))
+		return -EINVAL;
+
+	if (remap_pfn_range(vma,
+			    vma->vm_start,
+			    vma->vm_pgoff,
+			    size,
+			    vma->vm_page_prot))
+		return -EAGAIN;
+
+	return 0;
+}
+
+static const struct file_operations dev_fops = {
+	.owner = THIS_MODULE,
+	.unlocked_ioctl = xlnx_dpu_ioctl,
+	.mmap = xlnx_dpu_mmap,
+};
+
+/**
+ * get_irq - get irq
+ * @pdev:	dpu platform device
+ * @xdpu:	dpu structure
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static int get_irq(struct platform_device *pdev, struct xdpu_dev *xdpu)
+{
+	int ret, i;
+	int sfm_no = xdpu->dpu_cnt;
+	struct device *dev = xdpu->dev;
+
+	if (force_poll) {
+		dev_warn(dev, "no IRQ, using polling mode\n");
+		return 0;
+	}
+
+	for (i = 0; i < xdpu->dpu_cnt; i++) {
+		xdpu->cu[i].irq = platform_get_irq(pdev, i);
+		if (xdpu->cu[i].irq <= 0)
+			return -EINVAL;
+
+		ret = devm_request_irq(dev,
+				       xdpu->cu[i].irq,
+				       xlnx_dpu_isr,
+				       0,
+				       devm_kasprintf(dev,
+						      GFP_KERNEL,
+						      "%s-cu[%d]",
+						      dev_name(dev),
+						      i),
+				       xdpu);
+		if (ret < 0)
+			return ret;
+	}
+
+	if (xdpu->sfm_cnt) {
+		xdpu->cu[sfm_no].irq = platform_get_irq(pdev, sfm_no);
+		if (xdpu->cu[sfm_no].irq <= 0)
+			return -EINVAL;
+
+		ret = devm_request_irq(dev,
+				       xdpu->cu[sfm_no].irq,
+				       xlnx_dpu_isr,
+				       0,
+				       devm_kasprintf(dev,
+						      GFP_KERNEL,
+						      "%s-softmax",
+						      dev_name(dev)),
+				       xdpu);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_dpu_probe - probe dpu device
+ * @pdev: Pointer to dpu platform device structure
+ *
+ * Return: 0 if successful; otherwise -errno
+ */
+static int xlnx_dpu_probe(struct platform_device *pdev)
+{
+	int i, ret;
+	u32 val;
+	struct xdpu_dev *xdpu;
+	struct resource *res;
+	struct device *dev = &pdev->dev;
+
+	xdpu = devm_kzalloc(dev, sizeof(*xdpu), GFP_KERNEL);
+	if (!xdpu)
+		return -ENOMEM;
+
+	xdpu->dev = dev;
+
+	xdpu->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(xdpu->regs))
+		return -ENOMEM;
+
+	/*
+	 * DTG doesn't generate clock nodes in DT for Microblaze(MB),
+	 * using devm_clk_get_optional to return NULL in MB case, and return
+	 * required clock in ZynqMP case.
+	 */
+	xdpu->axi_clk = devm_clk_get_optional(xdpu->dev, "s_axi_aclk");
+	if (IS_ERR(xdpu->axi_clk))
+		return dev_err_probe(xdpu->dev, PTR_ERR(xdpu->axi_clk),
+				     "unable to get axi reference clock\n");
+
+	ret = clk_prepare_enable(xdpu->axi_clk);
+	if (ret) {
+		dev_err(xdpu->dev, "failed to enable s_axi_aclk(%d)\n", ret);
+		return ret;
+	}
+
+	xdpu->dpu_clk = devm_clk_get_optional(xdpu->dev, "m_axi_dpu_aclk");
+	if (IS_ERR(xdpu->dpu_clk))
+		return dev_err_probe(xdpu->dev, PTR_ERR(xdpu->dpu_clk),
+				     "unable to get m_axi_dpu_aclk\n");
+
+	ret = clk_prepare_enable(xdpu->dpu_clk);
+	if (ret) {
+		dev_err(xdpu->dev, "unable to enable dpu_clk(%d)\n", ret);
+		goto err_dpuclk;
+	}
+
+	xdpu->dsp_clk = devm_clk_get_optional(xdpu->dev, "dpu_2x_clk");
+	if (IS_ERR(xdpu->dsp_clk))
+		return dev_err_probe(xdpu->dev, PTR_ERR(xdpu->dsp_clk),
+				     "unable to get dsp clock\n");
+
+	ret = clk_prepare_enable(xdpu->dsp_clk);
+	if (ret) {
+		dev_err(xdpu->dev, "unable to enable dpu_2x_clk(%d)\n", ret);
+		goto err_dspclk;
+	}
+
+	/* dsp_clk should be dpu_clk * 2 */
+	if (xdpu->axi_clk && xdpu->dpu_clk && xdpu->dsp_clk)
+		dev_dbg(xdpu->dev,
+			"Freq: axilite: %lu MHz, dpu: %lu MHz, dsp: %lu MHz",
+			clk_get_rate(xdpu->axi_clk) / 1000000,
+			clk_get_rate(xdpu->dpu_clk) / 1000000,
+			clk_get_rate(xdpu->dsp_clk) / 1000000);
+
+	val = ioread32(xdpu->regs + DPU_IPVER_INFO);
+	if (DPU_VER(val) < DPU_IP_V3_4) {
+		dev_err(dev, "DPU IP need upgrade to 3.4 or later");
+		goto err_out;
+	}
+
+	xdpu->dpu_cnt = DPU_NUM(val);
+	xdpu->sfm_cnt = SFM_NUM(val);
+
+	val = ioread32(xdpu->regs + DPU_IPFREQENCY);
+	dev_dbg(dev, "found %d dpu core @%ldMHz and %d softmax core",
+		xdpu->dpu_cnt, DPU_FREQ(val), xdpu->sfm_cnt);
+
+	if (get_irq(pdev, xdpu))
+		goto err_out;
+
+	/* Try the reserved memory. Proceed if there's none */
+	ret = of_reserved_mem_device_init(dev);
+	if (ret && ret != -ENODEV)
+		goto err_out;
+
+	/* Vivado flow DPU ip is capable of 40-bit physical addresses only */
+	if (dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40))) {
+		/* fall back to 32-bit DMA mask */
+		if (dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32)))
+			goto err_out;
+	}
+
+	for (i = 0; i < xdpu->dpu_cnt + xdpu->sfm_cnt; i++) {
+		init_completion(&xdpu->cu[i].done);
+		mutex_init(&xdpu->cu[i].mutex);
+	}
+
+	INIT_LIST_HEAD(&xdpu->head);
+
+	xdpu->miscdev.minor = MISC_DYNAMIC_MINOR;
+	xdpu->miscdev.name = DEVICE_NAME;
+	xdpu->miscdev.fops = &dev_fops;
+	xdpu->miscdev.parent = dev;
+
+	if (misc_register(&xdpu->miscdev))
+		goto err_out;
+
+	xlnx_dpu_regs_init(xdpu);
+
+#ifdef CONFIG_DEBUG_FS
+	ret = dpu_debugfs_init(xdpu);
+	if (ret) {
+		dev_err(xdpu->dev, "failed to init dpu_debugfs)\n");
+		goto err_debugfs;
+	}
+#endif
+
+	platform_set_drvdata(pdev, xdpu);
+
+	dev_dbg(dev, "dpu registered as /dev/dpu successfully");
+
+	return 0;
+
+#ifdef CONFIG_DEBUG_FS
+err_debugfs:
+	misc_deregister(&xdpu->miscdev);
+#endif
+err_out:
+	clk_disable_unprepare(xdpu->dsp_clk);
+err_dspclk:
+	clk_disable_unprepare(xdpu->dpu_clk);
+err_dpuclk:
+	clk_disable_unprepare(xdpu->axi_clk);
+
+	return -EINVAL;
+}
+
+/**
+ * xlnx_dpu_remove - clean up structures
+ * @pdev:	The structure containing the device's details
+ *
+ * Return: 0 on success. -EINVAL for invalid value.
+ */
+static int xlnx_dpu_remove(struct platform_device *pdev)
+{
+	struct xdpu_dev *xdpu = platform_get_drvdata(pdev);
+	int i;
+
+	/* clean all regs */
+	for (i = 0; i < DPU_REG_END; i += 4)
+		iowrite32(0, xdpu->regs + i);
+
+#ifdef CONFIG_DEBUG_FS
+	debugfs_remove_recursive(xdpu->root);
+#endif
+	platform_set_drvdata(pdev, NULL);
+	misc_deregister(&xdpu->miscdev);
+
+	dev_dbg(xdpu->dev, "%s: device /dev/dpu unregistered\n", __func__);
+	return 0;
+}
+
+static const struct of_device_id dpu_of_match[] = {
+	{ .compatible = "xlnx,dpuczdx8g-3.4" },
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, dpu_of_match);
+
+static struct platform_driver xlnx_dpu_drv = {
+	.probe = xlnx_dpu_probe,
+	.remove = xlnx_dpu_remove,
+
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table = dpu_of_match,
+	},
+};
+
+module_platform_driver(xlnx_dpu_drv);
+
+#ifdef CONFIG_DEBUG_FS
+
+#define dump_register(n)			\
+{						\
+	.name	= #n,				\
+	.offset	= DPU_##n,				\
+}
+
+static const struct debugfs_reg32 cu_regs[4][38] = {
+	{
+	dump_register(IPVER_INFO),
+	dump_register(IPFREQENCY),
+	dump_register(TARGETID_L),
+	dump_register(TARGETID_H),
+	dump_register(IPSTART(0)),
+	dump_register(INSADDR(0)),
+	dump_register(ADDR0_L(0)),
+	dump_register(ADDR0_H(0)),
+	dump_register(ADDR1_L(0)),
+	dump_register(ADDR1_H(0)),
+	dump_register(ADDR2_L(0)),
+	dump_register(ADDR2_H(0)),
+	dump_register(ADDR3_L(0)),
+	dump_register(ADDR3_H(0)),
+	dump_register(ADDR4_L(0)),
+	dump_register(ADDR4_H(0)),
+	dump_register(ADDR5_L(0)),
+	dump_register(ADDR5_H(0)),
+	dump_register(ADDR6_L(0)),
+	dump_register(ADDR6_H(0)),
+	dump_register(ADDR7_L(0)),
+	dump_register(ADDR7_H(0)),
+	dump_register(CYCLE_L(0)),
+	dump_register(CYCLE_H(0)),
+	dump_register(P_STA_C(0)),
+	dump_register(P_END_C(0)),
+	dump_register(C_STA_C(0)),
+	dump_register(C_END_C(0)),
+	dump_register(S_STA_C(0)),
+	dump_register(S_END_C(0)),
+	dump_register(L_STA_C(0)),
+	dump_register(L_END_C(0)),
+	dump_register(AXI_STS(0)),
+	dump_register(HPBUS(0)),
+	dump_register(INT_STS),
+	dump_register(INT_MSK),
+	dump_register(INT_RAW),
+	dump_register(INT_ICR),
+	},
+	{
+	dump_register(IPVER_INFO),
+	dump_register(IPFREQENCY),
+	dump_register(TARGETID_L),
+	dump_register(TARGETID_H),
+	dump_register(IPSTART(1)),
+	dump_register(INSADDR(1)),
+	dump_register(ADDR0_L(1)),
+	dump_register(ADDR0_H(1)),
+	dump_register(ADDR1_L(1)),
+	dump_register(ADDR1_H(1)),
+	dump_register(ADDR2_L(1)),
+	dump_register(ADDR2_H(1)),
+	dump_register(ADDR3_L(1)),
+	dump_register(ADDR3_H(1)),
+	dump_register(ADDR4_L(1)),
+	dump_register(ADDR4_H(1)),
+	dump_register(ADDR5_L(1)),
+	dump_register(ADDR5_H(1)),
+	dump_register(ADDR6_L(1)),
+	dump_register(ADDR6_H(1)),
+	dump_register(ADDR7_L(1)),
+	dump_register(ADDR7_H(1)),
+	dump_register(CYCLE_L(1)),
+	dump_register(CYCLE_H(1)),
+	dump_register(P_STA_C(1)),
+	dump_register(P_END_C(1)),
+	dump_register(C_STA_C(1)),
+	dump_register(C_END_C(1)),
+	dump_register(S_STA_C(1)),
+	dump_register(S_END_C(1)),
+	dump_register(L_STA_C(1)),
+	dump_register(L_END_C(1)),
+	dump_register(AXI_STS(1)),
+	dump_register(HPBUS(1)),
+	dump_register(INT_STS),
+	dump_register(INT_MSK),
+	dump_register(INT_RAW),
+	dump_register(INT_ICR),
+	},
+	{
+	dump_register(IPVER_INFO),
+	dump_register(IPFREQENCY),
+	dump_register(TARGETID_L),
+	dump_register(TARGETID_H),
+	dump_register(IPSTART(2)),
+	dump_register(INSADDR(2)),
+	dump_register(ADDR0_L(2)),
+	dump_register(ADDR0_H(2)),
+	dump_register(ADDR1_L(2)),
+	dump_register(ADDR1_H(2)),
+	dump_register(ADDR2_L(2)),
+	dump_register(ADDR2_H(2)),
+	dump_register(ADDR3_L(2)),
+	dump_register(ADDR3_H(2)),
+	dump_register(ADDR4_L(2)),
+	dump_register(ADDR4_H(2)),
+	dump_register(ADDR5_L(2)),
+	dump_register(ADDR5_H(2)),
+	dump_register(ADDR6_L(2)),
+	dump_register(ADDR6_H(2)),
+	dump_register(ADDR7_L(2)),
+	dump_register(ADDR7_H(2)),
+	dump_register(CYCLE_L(2)),
+	dump_register(CYCLE_H(2)),
+	dump_register(P_STA_C(2)),
+	dump_register(P_END_C(2)),
+	dump_register(C_STA_C(2)),
+	dump_register(C_END_C(2)),
+	dump_register(S_STA_C(2)),
+	dump_register(S_END_C(2)),
+	dump_register(L_STA_C(2)),
+	dump_register(L_END_C(2)),
+	dump_register(AXI_STS(2)),
+	dump_register(HPBUS(2)),
+	dump_register(INT_STS),
+	dump_register(INT_MSK),
+	dump_register(INT_RAW),
+	dump_register(INT_ICR),
+	},
+	{
+	dump_register(IPVER_INFO),
+	dump_register(IPFREQENCY),
+	dump_register(TARGETID_L),
+	dump_register(TARGETID_H),
+	dump_register(IPSTART(3)),
+	dump_register(INSADDR(3)),
+	dump_register(ADDR0_L(3)),
+	dump_register(ADDR0_H(3)),
+	dump_register(ADDR1_L(3)),
+	dump_register(ADDR1_H(3)),
+	dump_register(ADDR2_L(3)),
+	dump_register(ADDR2_H(3)),
+	dump_register(ADDR3_L(3)),
+	dump_register(ADDR3_H(3)),
+	dump_register(ADDR4_L(3)),
+	dump_register(ADDR4_H(3)),
+	dump_register(ADDR5_L(3)),
+	dump_register(ADDR5_H(3)),
+	dump_register(ADDR6_L(3)),
+	dump_register(ADDR6_H(3)),
+	dump_register(ADDR7_L(3)),
+	dump_register(ADDR7_H(3)),
+	dump_register(CYCLE_L(3)),
+	dump_register(CYCLE_H(3)),
+	dump_register(P_STA_C(3)),
+	dump_register(P_END_C(3)),
+	dump_register(C_STA_C(3)),
+	dump_register(C_END_C(3)),
+	dump_register(S_STA_C(3)),
+	dump_register(S_END_C(3)),
+	dump_register(L_STA_C(3)),
+	dump_register(L_END_C(3)),
+	dump_register(AXI_STS(3)),
+	dump_register(HPBUS(3)),
+	dump_register(INT_STS),
+	dump_register(INT_MSK),
+	dump_register(INT_RAW),
+	dump_register(INT_ICR),
+	},
+};
+
+static const struct debugfs_reg32 sfm_regs[] = {
+	dump_register(IPVER_INFO),
+	dump_register(IPFREQENCY),
+	dump_register(TARGETID_L),
+	dump_register(TARGETID_H),
+	dump_register(SFM_INT_DONE),
+	dump_register(SFM_CMD_XLEN),
+	dump_register(SFM_CMD_YLEN),
+	dump_register(SFM_SRC_ADDR),
+	dump_register(SFM_DST_ADDR),
+	dump_register(SFM_CMD_SCAL),
+	dump_register(SFM_CMD_OFF),
+	dump_register(SFM_INT_CLR),
+	dump_register(SFM_START),
+	dump_register(SFM_RESET),
+	dump_register(SFM_MODE),
+	dump_register(INT_STS),
+	dump_register(INT_MSK),
+	dump_register(INT_RAW),
+	dump_register(INT_ICR),
+};
+
+static int dump_show(struct seq_file *seq, void *v)
+{
+	struct xdpu_dev *xdpu = seq->private;
+	struct dpu_buffer_block *h;
+	static const char units[] = "KMG";
+	const char *unit = units;
+	unsigned long delta = 0;
+
+	seq_puts(seq,
+		 "Virtual Address\t\t\t\tRequest Mem\t\tPhysical Address\n");
+	list_for_each_entry(h, &xdpu->head, head) {
+		delta = (h->capacity) >> 10;
+		while (!(delta & 1023) && unit[1]) {
+			delta >>= 10;
+			unit++;
+		}
+		seq_printf(seq, "%p-%p   %9lu%c         %016llx-%016llx\n",
+			   h->vaddr, h->vaddr + h->capacity,
+			   delta, *unit,
+			   (u64)h->dma_addr, (u64)(h->dma_addr + h->capacity));
+		delta = 0;
+		unit = units;
+	}
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(dump);
+
+/**
+ * dpu_debugfs_init - create DPU debugfs directory.
+ * @xdpu:	dpu structure
+ *
+ * Create DPU debugfs directory. Returns zero in case of success and a negative
+ * error code in case of failure.
+ *
+ * Return:	0 if successful; otherwise -errno
+ */
+static int dpu_debugfs_init(struct xdpu_dev *xdpu)
+{
+	char buf[32];
+	struct debugfs_regset32 *regset;
+	struct dentry *dentry;
+	int i;
+
+	xdpu->root = debugfs_create_dir("dpu", NULL);
+	if (IS_ERR(xdpu->root)) {
+		dev_err(xdpu->dev, "failed to create debugfs root\n");
+		return -ENODEV;
+	}
+
+	debugfs_create_file("dma_pool", 0444, xdpu->root, xdpu, &dump_fops);
+
+	for (i = 0; i < xdpu->dpu_cnt; i++) {
+		if (snprintf(buf, 32, "cu-%d", i) < 0)
+			return -EINVAL;
+
+		dentry = debugfs_create_dir(buf, xdpu->root);
+		regset = devm_kzalloc(xdpu->dev, sizeof(*regset), GFP_KERNEL);
+		if (!regset)
+			return -ENOMEM;
+
+		regset->regs = cu_regs[i];
+		regset->nregs = ARRAY_SIZE(cu_regs[i]);
+		regset->base = xdpu->regs;
+		debugfs_create_regset32("registers", 0444, dentry, regset);
+	}
+
+	if (xdpu->sfm_cnt) {
+		dentry = debugfs_create_dir("softmax", xdpu->root);
+		regset = devm_kzalloc(xdpu->dev, sizeof(*regset), GFP_KERNEL);
+		if (!regset)
+			return -ENOMEM;
+
+		regset->regs = sfm_regs;
+		regset->nregs = ARRAY_SIZE(sfm_regs);
+		regset->base = xdpu->regs;
+		debugfs_create_regset32("registers", 0444, dentry, regset);
+	}
+	return 0;
+}
+#endif
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_AUTHOR("Ye Yang <ye.yang@xilinx.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/misc/xlnx_dpu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/misc/xlnx_dpu.h
@@ -0,0 +1,186 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Xilinx, Inc.
+ *
+ */
+
+#ifndef _DPU_UAPI_H_
+#define _DPU_UAPI_H_
+
+/* up to 4 dpu cores and 1 softmax core */
+#define MAX_CU_NUM		5
+#define TIMEOUT			(timeout * CONFIG_HZ)
+#define TIMEOUT_US		(timeout * 1000000)
+#define POLL_PERIOD_US		(2000)
+
+/* DPU fingerprint, target info */
+#define DPU_PMU_IP_RST		(0x004)
+#define DPU_IPVER_INFO		(0x1E0)
+#define DPU_IPFREQENCY		(0x1E4)
+#define DPU_TARGETID_L		(0x1F0)
+#define DPU_TARGETID_H		(0x1F4)
+
+/* DPU core0-3 registers */
+#define DPU_HPBUS(x)		(0x200 + ((x) << 8))
+#define DPU_INSADDR(x)		(0x20C + ((x) << 8))
+#define DPU_IPSTART(x)		(0x220 + ((x) << 8))
+#define DPU_ADDR0_L(x)		(0x224 + ((x) << 8))
+#define DPU_ADDR0_H(x)		(0x228 + ((x) << 8))
+#define DPU_ADDR1_L(x)		(0x22C + ((x) << 8))
+#define DPU_ADDR1_H(x)		(0x230 + ((x) << 8))
+#define DPU_ADDR2_L(x)		(0x234 + ((x) << 8))
+#define DPU_ADDR2_H(x)		(0x238 + ((x) << 8))
+#define DPU_ADDR3_L(x)		(0x23C + ((x) << 8))
+#define DPU_ADDR3_H(x)		(0x240 + ((x) << 8))
+#define DPU_ADDR4_L(x)		(0x244 + ((x) << 8))
+#define DPU_ADDR4_H(x)		(0x248 + ((x) << 8))
+#define DPU_ADDR5_L(x)		(0x24C + ((x) << 8))
+#define DPU_ADDR5_H(x)		(0x250 + ((x) << 8))
+#define DPU_ADDR6_L(x)		(0x254 + ((x) << 8))
+#define DPU_ADDR6_H(x)		(0x258 + ((x) << 8))
+#define DPU_ADDR7_L(x)		(0x25C + ((x) << 8))
+#define DPU_ADDR7_H(x)		(0x260 + ((x) << 8))
+#define DPU_P_END_C(x)		(0x264 + ((x) << 8))
+#define DPU_C_END_C(x)		(0x268 + ((x) << 8))
+#define DPU_S_END_C(x)		(0x26C + ((x) << 8))
+#define DPU_L_END_C(x)		(0x270 + ((x) << 8))
+#define DPU_P_STA_C(x)		(0x274 + ((x) << 8))
+#define DPU_C_STA_C(x)		(0x278 + ((x) << 8))
+#define DPU_S_STA_C(x)		(0x27C + ((x) << 8))
+#define DPU_L_STA_C(x)		(0x280 + ((x) << 8))
+#define DPU_AXI_STS(x)		(0x284 + ((x) << 8))
+#define DPU_CYCLE_L(x)		(0x290 + ((x) << 8))
+#define DPU_CYCLE_H(x)		(0x294 + ((x) << 8))
+
+/* DPU INT Registers */
+#define DPU_INT_STS		(0x600)
+#define DPU_INT_MSK		(0x604)
+#define DPU_INT_RAW		(0x608)
+#define DPU_INT_ICR		(0x60C)
+
+/* DPU Softmax Registers */
+#define DPU_SFM_INT_DONE	(0x700)
+#define DPU_SFM_CMD_XLEN	(0x704)
+#define DPU_SFM_CMD_YLEN	(0x708)
+#define DPU_SFM_SRC_ADDR	(0x70C)
+#define DPU_SFM_DST_ADDR	(0x710)
+#define DPU_SFM_CMD_SCAL	(0x714)
+#define DPU_SFM_CMD_OFF		(0x718)
+#define DPU_SFM_INT_CLR		(0x71C)
+#define DPU_SFM_START		(0x720)
+#define DPU_SFM_RESET		(0x730)
+#define DPU_SFM_MODE		(0x738)
+#define DPU_REG_END		(0x800)
+
+#define DPU_NUM(x)		(GENMASK(3, 0) & (x))
+#define DPU_FREQ(x)		(GENMASK(11, 0) & (x))
+#define SFM_NUM(x)		((GENMASK(7, 4) & (x)) >> 4)
+#define DPU_VER(x)		((GENMASK(31, 24) & (x)) >> 24)
+#define DPU_SUB_VER(x)		((GENMASK(23, 16) & (x)) >> 16)
+#define DPU_SAXI(x)		((GENMASK(23, 12) & (x)) >> 12)
+
+#define DPU_HPBUS_VAL		(0x07070f0f)
+#define DPU_RST_ALL_CORES	(0xF)
+#define DPU_INSTR_OFFSET	(12)
+#define DPU_IP_V3_4		(0x34)
+
+enum DPU_DMA_DIR {
+	CPU_TO_DPU = 0,
+	DPU_TO_CPU = 1
+};
+
+struct dpcma_req_free {
+	u64 phy_addr;
+	size_t capacity;
+};
+
+struct dpcma_req_alloc {
+	size_t size;
+	u64 phy_addr;
+	size_t capacity;
+};
+
+struct dpcma_req_sync {
+	u64 phy_addr;
+	size_t size;
+	int direction;
+};
+
+/**
+ * struct  ioc_kernel_run_t - describe structure for each dpu ioctl
+ * @addr_code:	the address for DPU code
+ * @addr0:	address reg0
+ * @addr1:	address reg1
+ * @addr2:	address reg2
+ * @addr3:	address reg3
+ * @addr4:	address reg4
+ * @addr5:	address reg5
+ * @addr6:	address reg6
+ * @addr7:	address reg7
+ * @time_start:	the start timestamp before running
+ * @time_end:	the end timestamp after running
+ * @counter:	nums of total cycles
+ * @core_id:	the DPU core id
+ * @pend_cnt:	finished counts of dpu misc
+ * @cend_cnt:	finished counts of dpu conv
+ * @send_cnt:	finished counts of dpu save
+ * @lend_cnt:	finished counts of dpu load
+ * @pstart_cnt:	initiated counts of dpu misc
+ * @cstart_cnt:	initiated counts of dpu conv
+ * @sstart_cnt:	initiated counts of dpu save
+ * @lstart_cnt:	initiated counts of dpu load
+ */
+struct ioc_kernel_run_t {
+	u64 addr_code;
+	u64 addr0;
+	u64 addr1;
+	u64 addr2;
+	u64 addr3;
+	u64 addr4;
+	u64 addr5;
+	u64 addr6;
+	u64 addr7;
+	u64 time_start;
+	u64 time_end;
+	u64 counter;
+	int core_id;
+	u32 pend_cnt;
+	u32 cend_cnt;
+	u32 send_cnt;
+	u32 lend_cnt;
+	u32 pstart_cnt;
+	u32 cstart_cnt;
+	u32 sstart_cnt;
+	u32 lstart_cnt;
+};
+
+/**
+ * struct  ioc_softmax_t - describe structure for each softmax ioctl
+ * @width:	width dimension of Tensor
+ * @height:	height dimension of Tensor
+ * @input:	physical address of input Tensor
+ * @output:	physical address of output Tensor
+ * @scale:	quantization info of input Tensor
+ * @offset:	offset value for input Tensor
+ */
+struct ioc_softmax_t {
+	u32 width;
+	u32 height;
+	u32 input;
+	u32 output;
+	u32 scale;
+	u32 offset;
+};
+
+#define DPU_IOC_MAGIC 'D'
+
+#define DPUIOC_CREATE_BO _IOWR(DPU_IOC_MAGIC, 1, struct dpcma_req_alloc*)
+#define DPUIOC_FREE_BO _IOWR(DPU_IOC_MAGIC, 2, struct dpcma_req_free*)
+#define DPUIOC_SYNC_BO _IOWR(DPU_IOC_MAGIC, 3, struct dpcma_req_sync*)
+#define DPUIOC_G_INFO _IOR(DPU_IOC_MAGIC, 4, u32)
+#define DPUIOC_G_TGTID _IOR(DPU_IOC_MAGIC, 5, u64)
+#define DPUIOC_RUN _IOWR(DPU_IOC_MAGIC, 6, struct ioc_kernel_run_t*)
+#define DPUIOC_RUN_SOFTMAX _IOWR(DPU_IOC_MAGIC, 7, struct ioc_softmax_t*)
+#define DPUIOC_REG_READ _IOR(DPU_IOC_MAGIC, 8, u32)
+
+#endif /* _DPU_UAPI_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/block.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/block.c
@@ -133,6 +133,7 @@
 	 * track of the current selected device partition.
 	 */
 	unsigned int	part_curr;
+#define MMC_BLK_PART_INVALID	UINT_MAX	/* Unknown partition active */
 	int	area_type;
 
 	/* debugfs files (only in main mmc_blk_data) */
@@ -175,7 +176,7 @@
 				      unsigned int part_type);
 static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
 			       struct mmc_card *card,
-			       int disable_multi,
+			       int recovery_mode,
 			       struct mmc_queue *mq);
 static void mmc_blk_hsq_req_done(struct mmc_request *mrq);
 
@@ -264,6 +265,7 @@
 		goto out_put;
 	}
 	req_to_mmc_queue_req(req)->drv_op = MMC_DRV_OP_BOOT_WP;
+	req_to_mmc_queue_req(req)->drv_op_result = -EIO;
 	blk_execute_rq(NULL, req, 0);
 	ret = req_to_mmc_queue_req(req)->drv_op_result;
 	blk_put_request(req);
@@ -397,6 +399,10 @@
 	struct mmc_ioc_cmd ic;
 	unsigned char *buf;
 	u64 buf_bytes;
+	unsigned int flags;
+#define MMC_BLK_IOC_DROP	BIT(0)	/* drop this mrq */
+#define MMC_BLK_IOC_SBC	BIT(1)	/* use mrq.sbc */
+
 	struct mmc_rpmb_data *rpmb;
 };
 
@@ -406,7 +412,7 @@
 	struct mmc_blk_ioc_data *idata;
 	int err;
 
-	idata = kmalloc(sizeof(*idata), GFP_KERNEL);
+	idata = kzalloc(sizeof(*idata), GFP_KERNEL);
 	if (!idata) {
 		err = -ENOMEM;
 		goto out;
@@ -462,7 +468,7 @@
 }
 
 static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md,
-			       struct mmc_blk_ioc_data *idata)
+			       struct mmc_blk_ioc_data **idatas, int i)
 {
 	struct mmc_command cmd = {}, sbc = {};
 	struct mmc_data data = {};
@@ -470,10 +476,18 @@
 	struct scatterlist sg;
 	int err;
 	unsigned int target_part;
+	struct mmc_blk_ioc_data *idata = idatas[i];
+	struct mmc_blk_ioc_data *prev_idata = NULL;
 
 	if (!card || !md || !idata)
 		return -EINVAL;
 
+	if (idata->flags & MMC_BLK_IOC_DROP)
+		return 0;
+
+	if (idata->flags & MMC_BLK_IOC_SBC && i > 0)
+		prev_idata = idatas[i - 1];
+
 	/*
 	 * The RPMB accesses comes in from the character device, so we
 	 * need to target these explicitly. Else we just target the
@@ -540,7 +554,7 @@
 			return err;
 	}
 
-	if (idata->rpmb) {
+	if (idata->rpmb || prev_idata) {
 		sbc.opcode = MMC_SET_BLOCK_COUNT;
 		/*
 		 * We don't do any blockcount validation because the max size
@@ -548,6 +562,8 @@
 		 * 'Reliable Write' bit here.
 		 */
 		sbc.arg = data.blocks | (idata->ic.write_flag & BIT(31));
+		if (prev_idata)
+			sbc.arg = prev_idata->ic.arg;
 		sbc.flags = MMC_RSP_R1 | MMC_CMD_AC;
 		mrq.sbc = &sbc;
 	}
@@ -559,6 +575,15 @@
 	mmc_wait_for_req(card->host, &mrq);
 	memcpy(&idata->ic.response, cmd.resp, sizeof(cmd.resp));
 
+	if (prev_idata) {
+		memcpy(&prev_idata->ic.response, sbc.resp, sizeof(sbc.resp));
+		if (sbc.error) {
+			dev_err(mmc_dev(card->host), "%s: sbc error %d\n",
+							__func__, sbc.error);
+			return sbc.error;
+		}
+	}
+
 	if (cmd.error) {
 		dev_err(mmc_dev(card->host), "%s: cmd error %d\n",
 						__func__, cmd.error);
@@ -609,11 +634,11 @@
 
 	if (idata->rpmb || (cmd.flags & MMC_RSP_R1B) == MMC_RSP_R1B) {
 		/*
-		 * Ensure RPMB/R1B command has completed by polling CMD13
-		 * "Send Status".
+		 * Ensure RPMB/R1B command has completed by polling CMD13 "Send Status". Here we
+		 * allow to override the default timeout value if a custom timeout is specified.
 		 */
-		err = mmc_poll_for_busy(card, MMC_BLK_TIMEOUT_MS, false,
-					MMC_BUSY_IO);
+		err = mmc_poll_for_busy(card, idata->ic.cmd_timeout_ms ? : MMC_BLK_TIMEOUT_MS,
+					false, MMC_BUSY_IO);
 	}
 
 	return err;
@@ -655,6 +680,7 @@
 	idatas[0] = idata;
 	req_to_mmc_queue_req(req)->drv_op =
 		rpmb ? MMC_DRV_OP_IOCTL_RPMB : MMC_DRV_OP_IOCTL;
+	req_to_mmc_queue_req(req)->drv_op_result = -EIO;
 	req_to_mmc_queue_req(req)->drv_op_data = idatas;
 	req_to_mmc_queue_req(req)->ioc_count = 1;
 	blk_execute_rq(NULL, req, 0);
@@ -724,6 +750,7 @@
 	}
 	req_to_mmc_queue_req(req)->drv_op =
 		rpmb ? MMC_DRV_OP_IOCTL_RPMB : MMC_DRV_OP_IOCTL;
+	req_to_mmc_queue_req(req)->drv_op_result = -EIO;
 	req_to_mmc_queue_req(req)->drv_op_data = idata;
 	req_to_mmc_queue_req(req)->ioc_count = num_of_cmds;
 	blk_execute_rq(NULL, req, 0);
@@ -835,9 +862,11 @@
 static int mmc_blk_part_switch_pre(struct mmc_card *card,
 				   unsigned int part_type)
 {
+	const unsigned int mask = EXT_CSD_PART_CONFIG_ACC_MASK;
+	const unsigned int rpmb = EXT_CSD_PART_CONFIG_ACC_RPMB;
 	int ret = 0;
 
-	if (part_type == EXT_CSD_PART_CONFIG_ACC_RPMB) {
+	if ((part_type & mask) == rpmb) {
 		if (card->ext_csd.cmdq_en) {
 			ret = mmc_cmdq_disable(card);
 			if (ret)
@@ -852,9 +881,11 @@
 static int mmc_blk_part_switch_post(struct mmc_card *card,
 				    unsigned int part_type)
 {
+	const unsigned int mask = EXT_CSD_PART_CONFIG_ACC_MASK;
+	const unsigned int rpmb = EXT_CSD_PART_CONFIG_ACC_RPMB;
 	int ret = 0;
 
-	if (part_type == EXT_CSD_PART_CONFIG_ACC_RPMB) {
+	if ((part_type & mask) == rpmb) {
 		mmc_retune_unpause(card->host);
 		if (card->reenable_cmdq && !card->ext_csd.cmdq_en)
 			ret = mmc_cmdq_enable(card);
@@ -984,9 +1015,16 @@
 	return ms;
 }
 
+/*
+ * Attempts to reset the card and get back to the requested partition.
+ * Therefore any error here must result in cancelling the block layer
+ * request, it must not be reattempted without going through the mmc_blk
+ * partition sanity checks.
+ */
 static int mmc_blk_reset(struct mmc_blk_data *md, struct mmc_host *host,
 			 int type)
 {
+	struct mmc_blk_data *main_md = dev_get_drvdata(&host->card->dev);
 	int err;
 
 	if (md->reset_done & type)
@@ -994,23 +1032,22 @@
 
 	md->reset_done |= type;
 	err = mmc_hw_reset(host);
+	/*
+	 * A successful reset will leave the card in the main partition, but
+	 * upon failure it might not be, so set it to MMC_BLK_PART_INVALID
+	 * in that case.
+	 */
+	main_md->part_curr = err ? MMC_BLK_PART_INVALID : main_md->part_type;
+	if (err)
+		return err;
 	/* Ensure we switch back to the correct partition */
-	if (err) {
-		struct mmc_blk_data *main_md =
-			dev_get_drvdata(&host->card->dev);
-		int part_err;
-
-		main_md->part_curr = main_md->part_type;
-		part_err = mmc_blk_part_switch(host->card, md->part_type);
-		if (part_err) {
-			/*
-			 * We have failed to get back into the correct
-			 * partition, so we need to abort the whole request.
-			 */
-			return -ENODEV;
-		}
-	}
-	return err;
+	if (mmc_blk_part_switch(host->card, md->part_type))
+		/*
+		 * We have failed to get back into the correct
+		 * partition, so we need to abort the whole request.
+		 */
+		return -ENODEV;
+	return 0;
 }
 
 static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)
@@ -1018,6 +1055,20 @@
 	md->reset_done &= ~type;
 }
 
+static void mmc_blk_check_sbc(struct mmc_queue_req *mq_rq)
+{
+	struct mmc_blk_ioc_data **idata = mq_rq->drv_op_data;
+	int i;
+
+	for (i = 1; i < mq_rq->ioc_count; i++) {
+		if (idata[i - 1]->ic.opcode == MMC_SET_BLOCK_COUNT &&
+		    mmc_op_multi(idata[i]->ic.opcode)) {
+			idata[i - 1]->flags |= MMC_BLK_IOC_DROP;
+			idata[i]->flags |= MMC_BLK_IOC_SBC;
+		}
+	}
+}
+
 /*
  * The non-block commands come back from the block layer after it queued it and
  * processed it with all other requests and then they get issued in this
@@ -1045,11 +1096,14 @@
 			if (ret)
 				break;
 		}
+
+		mmc_blk_check_sbc(mq_rq);
+
 		fallthrough;
 	case MMC_DRV_OP_IOCTL_RPMB:
 		idata = mq_rq->drv_op_data;
 		for (i = 0, ret = 0; i < mq_rq->ioc_count; i++) {
-			ret = __mmc_blk_ioctl_cmd(card, md, idata[i]);
+			ret = __mmc_blk_ioctl_cmd(card, md, idata, i);
 			if (ret)
 				break;
 		}
@@ -1107,6 +1161,11 @@
 	nr = blk_rq_sectors(req);
 
 	do {
+		unsigned int erase_arg = card->erase_arg;
+
+		if (mmc_card_broken_sd_discard(card))
+			erase_arg = SD_ERASE_ARG;
+
 		err = 0;
 		if (card->quirks & MMC_QUIRK_INAND_CMD38) {
 			err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
@@ -1117,7 +1176,7 @@
 					 card->ext_csd.generic_cmd6_time);
 		}
 		if (!err)
-			err = mmc_erase(card, from, nr, card->erase_arg);
+			err = mmc_erase(card, from, nr, erase_arg);
 	} while (err == -EIO && !mmc_blk_reset(md, card->host, type));
 	if (err)
 		status = BLK_STS_IOERR;
@@ -1285,7 +1344,7 @@
 }
 
 static void mmc_blk_data_prep(struct mmc_queue *mq, struct mmc_queue_req *mqrq,
-			      int disable_multi, bool *do_rel_wr_p,
+			      int recovery_mode, bool *do_rel_wr_p,
 			      bool *do_data_tag_p)
 {
 	struct mmc_blk_data *md = mq->blkdata;
@@ -1351,12 +1410,12 @@
 			brq->data.blocks--;
 
 		/*
-		 * After a read error, we redo the request one sector
+		 * After a read error, we redo the request one (native) sector
 		 * at a time in order to accurately determine which
 		 * sectors can be read successfully.
 		 */
-		if (disable_multi)
-			brq->data.blocks = 1;
+		if (recovery_mode)
+			brq->data.blocks = queue_physical_block_size(mq->queue) >> 9;
 
 		/*
 		 * Some controllers have HW issues while operating
@@ -1450,6 +1509,8 @@
 			blk_mq_requeue_request(req, true);
 		else
 			__blk_mq_end_request(req, BLK_STS_OK);
+	} else if (mq->in_recovery) {
+		blk_mq_requeue_request(req, true);
 	} else {
 		blk_mq_end_request(req, BLK_STS_OK);
 	}
@@ -1482,8 +1543,7 @@
 	err = mmc_cqe_recovery(host);
 	if (err)
 		mmc_blk_reset(mq->blkdata, host, MMC_BLK_CQE_RECOVERY);
-	else
-		mmc_blk_reset_success(mq->blkdata, MMC_BLK_CQE_RECOVERY);
+	mmc_blk_reset_success(mq->blkdata, MMC_BLK_CQE_RECOVERY);
 
 	pr_debug("%s: CQE recovery done\n", mmc_hostname(host));
 }
@@ -1574,7 +1634,7 @@
 
 static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
 			       struct mmc_card *card,
-			       int disable_multi,
+			       int recovery_mode,
 			       struct mmc_queue *mq)
 {
 	u32 readcmd, writecmd;
@@ -1583,7 +1643,7 @@
 	struct mmc_blk_data *md = mq->blkdata;
 	bool do_rel_wr, do_data_tag;
 
-	mmc_blk_data_prep(mq, mqrq, disable_multi, &do_rel_wr, &do_data_tag);
+	mmc_blk_data_prep(mq, mqrq, recovery_mode, &do_rel_wr, &do_data_tag);
 
 	brq->mrq.cmd = &brq->cmd;
 
@@ -1674,7 +1734,7 @@
 
 #define MMC_READ_SINGLE_RETRIES	2
 
-/* Single sector read during recovery */
+/* Single (native) sector read during recovery */
 static void mmc_blk_read_single(struct mmc_queue *mq, struct request *req)
 {
 	struct mmc_queue_req *mqrq = req_to_mmc_queue_req(req);
@@ -1682,31 +1742,32 @@
 	struct mmc_card *card = mq->card;
 	struct mmc_host *host = card->host;
 	blk_status_t error = BLK_STS_OK;
-	int retries = 0;
+	size_t bytes_per_read = queue_physical_block_size(mq->queue);
 
 	do {
 		u32 status;
 		int err;
+		int retries = 0;
 
-		mmc_blk_rw_rq_prep(mqrq, card, 1, mq);
+		while (retries++ <= MMC_READ_SINGLE_RETRIES) {
+			mmc_blk_rw_rq_prep(mqrq, card, 1, mq);
 
-		mmc_wait_for_req(host, mrq);
+			mmc_wait_for_req(host, mrq);
 
-		err = mmc_send_status(card, &status);
-		if (err)
-			goto error_exit;
-
-		if (!mmc_host_is_spi(host) &&
-		    !mmc_ready_for_data(status)) {
-			err = mmc_blk_fix_state(card, req);
+			err = mmc_send_status(card, &status);
 			if (err)
 				goto error_exit;
-		}
 
-		if (mrq->cmd->error && retries++ < MMC_READ_SINGLE_RETRIES)
-			continue;
+			if (!mmc_host_is_spi(host) &&
+			    !mmc_ready_for_data(status)) {
+				err = mmc_blk_fix_state(card, req);
+				if (err)
+					goto error_exit;
+			}
 
-		retries = 0;
+			if (!mrq->cmd->error)
+				break;
+		}
 
 		if (mrq->cmd->error ||
 		    mrq->data->error ||
@@ -1716,13 +1777,13 @@
 		else
 			error = BLK_STS_OK;
 
-	} while (blk_update_request(req, error, 512));
+	} while (blk_update_request(req, error, bytes_per_read));
 
 	return;
 
 error_exit:
 	mrq->data->bytes_xfered = 0;
-	blk_update_request(req, BLK_STS_IOERR, 512);
+	blk_update_request(req, BLK_STS_IOERR, bytes_per_read);
 	/* Let it try the remaining request again */
 	if (mqrq->retries > MMC_MAX_RETRIES - 1)
 		mqrq->retries = MMC_MAX_RETRIES - 1;
@@ -1850,8 +1911,9 @@
 		return;
 
 	/* Reset before last retry */
-	if (mqrq->retries + 1 == MMC_MAX_RETRIES)
-		mmc_blk_reset(md, card->host, type);
+	if (mqrq->retries + 1 == MMC_MAX_RETRIES &&
+	    mmc_blk_reset(md, card->host, type))
+		return;
 
 	/* Command errors fail fast, so use all MMC_MAX_RETRIES */
 	if (brq->sbc.error || brq->cmd.error)
@@ -1863,10 +1925,9 @@
 		return;
 	}
 
-	/* FIXME: Missing single sector read for large sector size */
-	if (!mmc_large_sector(card) && rq_data_dir(req) == READ &&
-	    brq->data.blocks > 1) {
-		/* Read one sector at a time */
+	if (rq_data_dir(req) == READ && brq->data.blocks >
+			queue_physical_block_size(mq->queue) >> 9) {
+		/* Read one (native) sector at a time */
 		mmc_blk_read_single(mq, req);
 		return;
 	}
@@ -1880,6 +1941,31 @@
 	       brq->data.error || brq->cmd.resp[0] & CMD_ERRORS;
 }
 
+static int mmc_spi_err_check(struct mmc_card *card)
+{
+	u32 status = 0;
+	int err;
+
+	/*
+	 * SPI does not have a TRAN state we have to wait on, instead the
+	 * card is ready again when it no longer holds the line LOW.
+	 * We still have to ensure two things here before we know the write
+	 * was successful:
+	 * 1. The card has not disconnected during busy and we actually read our
+	 * own pull-up, thinking it was still connected, so ensure it
+	 * still responds.
+	 * 2. Check for any error bits, in particular R1_SPI_IDLE to catch a
+	 * just reconnected card after being disconnected during busy.
+	 */
+	err = __mmc_send_status(card, &status, 0);
+	if (err)
+		return err;
+	/* All R1 and R2 bits of SPI are errors in our case */
+	if (status)
+		return -EIO;
+	return 0;
+}
+
 static int mmc_blk_busy_cb(void *cb_data, bool *busy)
 {
 	struct mmc_blk_busy_data *data = cb_data;
@@ -1903,9 +1989,16 @@
 	struct mmc_blk_busy_data cb_data;
 	int err;
 
-	if (mmc_host_is_spi(card->host) || rq_data_dir(req) == READ)
+	if (rq_data_dir(req) == READ)
 		return 0;
 
+	if (mmc_host_is_spi(card->host)) {
+		err = mmc_spi_err_check(card);
+		if (err)
+			mqrq->brq.data.bytes_xfered = 0;
+		return err;
+	}
+
 	cb_data.card = card;
 	cb_data.status = 0;
 	err = __mmc_poll_for_busy(card, MMC_BLK_TIMEOUT_MS, &mmc_blk_busy_cb,
@@ -2034,14 +2127,14 @@
 	mmc_blk_urgent_bkops(mq, mqrq);
 }
 
-static void mmc_blk_mq_dec_in_flight(struct mmc_queue *mq, struct request *req)
+static void mmc_blk_mq_dec_in_flight(struct mmc_queue *mq, enum mmc_issue_type issue_type)
 {
 	unsigned long flags;
 	bool put_card;
 
 	spin_lock_irqsave(&mq->lock, flags);
 
-	mq->in_flight[mmc_issue_type(mq, req)] -= 1;
+	mq->in_flight[issue_type] -= 1;
 
 	put_card = (mmc_tot_in_flight(mq) == 0);
 
@@ -2053,6 +2146,7 @@
 
 static void mmc_blk_mq_post_req(struct mmc_queue *mq, struct request *req)
 {
+	enum mmc_issue_type issue_type = mmc_issue_type(mq, req);
 	struct mmc_queue_req *mqrq = req_to_mmc_queue_req(req);
 	struct mmc_request *mrq = &mqrq->brq.mrq;
 	struct mmc_host *host = mq->card->host;
@@ -2068,7 +2162,7 @@
 	else if (likely(!blk_should_fake_timeout(req->q)))
 		blk_mq_complete_request(req);
 
-	mmc_blk_mq_dec_in_flight(mq, req);
+	mmc_blk_mq_dec_in_flight(mq, issue_type);
 }
 
 void mmc_blk_mq_recovery(struct mmc_queue *mq)
@@ -2344,6 +2438,8 @@
 	struct mmc_blk_data *md;
 	int devidx, ret;
 	char cap_str[10];
+	bool cache_enabled = false;
+	bool fua_enabled = false;
 
 	devidx = ida_simple_get(&mmc_blk_ida, 0, max_devices, GFP_KERNEL);
 	if (devidx < 0) {
@@ -2397,8 +2493,8 @@
 	set_disk_ro(md->disk, md->read_only || default_ro);
 	md->disk->flags = GENHD_FL_EXT_DEVT;
 	if (area_type & (MMC_BLK_DATA_AREA_RPMB | MMC_BLK_DATA_AREA_BOOT))
-		md->disk->flags |= GENHD_FL_NO_PART_SCAN
-				   | GENHD_FL_SUPPRESS_PARTITION_INFO;
+		md->disk->flags |= GENHD_FL_NO_PART |
+				   GENHD_FL_SUPPRESS_PARTITION_INFO;
 
 	/*
 	 * As discussed on lkml, GENHD_FL_REMOVABLE should:
@@ -2425,13 +2521,17 @@
 			md->flags |= MMC_BLK_CMD23;
 	}
 
-	if (mmc_card_mmc(card) &&
-	    md->flags & MMC_BLK_CMD23 &&
+	if (md->flags & MMC_BLK_CMD23 &&
 	    ((card->ext_csd.rel_param & EXT_CSD_WR_REL_PARAM_EN) ||
 	     card->ext_csd.rel_sectors)) {
 		md->flags |= MMC_BLK_REL_WR;
-		blk_queue_write_cache(md->queue.queue, true, true);
+		fua_enabled = true;
+		cache_enabled = true;
 	}
+	if (mmc_cache_enabled(card->host))
+		cache_enabled  = true;
+
+	blk_queue_write_cache(md->queue.queue, cache_enabled, fua_enabled);
 
 	string_get_size((u64)size, 512, STRING_UNITS_2,
 			cap_str, sizeof(cap_str));
@@ -2734,6 +2834,7 @@
 	if (IS_ERR(req))
 		return PTR_ERR(req);
 	req_to_mmc_queue_req(req)->drv_op = MMC_DRV_OP_GET_CARD_STATUS;
+	req_to_mmc_queue_req(req)->drv_op_result = -EIO;
 	blk_execute_rq(NULL, req, 0);
 	ret = req_to_mmc_queue_req(req)->drv_op_result;
 	if (ret >= 0) {
@@ -2772,6 +2873,7 @@
 		goto out_free;
 	}
 	req_to_mmc_queue_req(req)->drv_op = MMC_DRV_OP_GET_EXT_CSD;
+	req_to_mmc_queue_req(req)->drv_op_result = -EIO;
 	req_to_mmc_queue_req(req)->drv_op_data = &ext_csd;
 	blk_execute_rq(NULL, req, 0);
 	err = req_to_mmc_queue_req(req)->drv_op_result;
@@ -3068,4 +3170,3 @@
 
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Multimedia Card (MMC) block device driver");
-
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/bus.c
@@ -158,6 +158,8 @@
 	if (dev->driver && drv->shutdown)
 		drv->shutdown(card);
 
+	__mmc_stop_host(host);
+
 	if (host->bus_ops->shutdown) {
 		ret = host->bus_ops->shutdown(host);
 		if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/card.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/card.h
@@ -70,6 +70,7 @@
 #define EXT_CSD_REV_ANY (-1u)
 
 #define CID_MANFID_SANDISK      0x2
+#define CID_MANFID_SANDISK_SD   0x3
 #define CID_MANFID_ATP          0x9
 #define CID_MANFID_TOSHIBA      0x11
 #define CID_MANFID_MICRON       0x13
@@ -222,4 +223,9 @@
 	return c->quirks & MMC_QUIRK_BROKEN_HPI;
 }
 
+static inline int mmc_card_broken_sd_discard(const struct mmc_card *c)
+{
+	return c->quirks & MMC_QUIRK_BROKEN_SD_DISCARD;
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/core.c
@@ -552,7 +552,9 @@
 	cmd.flags        = MMC_RSP_R1B | MMC_CMD_AC;
 	cmd.flags       &= ~MMC_RSP_CRC; /* Ignore CRC */
 	cmd.busy_timeout = MMC_CQE_RECOVERY_TIMEOUT;
-	mmc_wait_for_cmd(host, &cmd, 0);
+	mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
+
+	mmc_poll_for_busy(host->card, MMC_CQE_RECOVERY_TIMEOUT, true, MMC_BUSY_IO);
 
 	memset(&cmd, 0, sizeof(cmd));
 	cmd.opcode       = MMC_CMDQ_TASK_MGMT;
@@ -560,10 +562,13 @@
 	cmd.flags        = MMC_RSP_R1B | MMC_CMD_AC;
 	cmd.flags       &= ~MMC_RSP_CRC; /* Ignore CRC */
 	cmd.busy_timeout = MMC_CQE_RECOVERY_TIMEOUT;
-	err = mmc_wait_for_cmd(host, &cmd, 0);
+	err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
 
 	host->cqe_ops->cqe_recovery_finish(host);
 
+	if (err)
+		err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
+
 	mmc_retune_release(host);
 
 	return err;
@@ -1132,7 +1137,13 @@
 		mmc_power_cycle(host, ocr);
 	} else {
 		bit = fls(ocr) - 1;
-		ocr &= 3 << bit;
+		/*
+		 * The bit variable represents the highest voltage bit set in
+		 * the OCR register.
+		 * To keep a range of 2 values (e.g. 3.2V/3.3V and 3.3V/3.4V),
+		 * we must shift the mask '3' with (bit - 1).
+		 */
+		ocr &= 3 << (bit - 1);
 		if (bit != host->ios.vdd)
 			dev_warn(mmc_dev(host), "exceeding card's volts\n");
 	}
@@ -1476,6 +1487,11 @@
 		card->pref_erase = 0;
 }
 
+static bool is_trim_arg(unsigned int arg)
+{
+	return (arg & MMC_TRIM_OR_DISCARD_ARGS) && arg != MMC_DISCARD_ARG;
+}
+
 static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card,
 				          unsigned int arg, unsigned int qty)
 {
@@ -1758,7 +1774,7 @@
 	    !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN))
 		return -EOPNOTSUPP;
 
-	if (mmc_card_mmc(card) && (arg & MMC_TRIM_ARGS) &&
+	if (mmc_card_mmc(card) && is_trim_arg(arg) &&
 	    !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN))
 		return -EOPNOTSUPP;
 
@@ -1788,7 +1804,7 @@
 	 * identified by the card->eg_boundary flag.
 	 */
 	rem = card->erase_size - (from % card->erase_size);
-	if ((arg & MMC_TRIM_ARGS) && (card->eg_boundary) && (nr > rem)) {
+	if ((arg & MMC_TRIM_OR_DISCARD_ARGS) && card->eg_boundary && nr > rem) {
 		err = mmc_do_erase(card, from, from + rem - 1, arg);
 		from += rem;
 		if ((err) || (to <= from))
@@ -2264,8 +2280,11 @@
 	_mmc_detect_change(host, 0, false);
 }
 
-void mmc_stop_host(struct mmc_host *host)
+void __mmc_stop_host(struct mmc_host *host)
 {
+	if (host->rescan_disable)
+		return;
+
 	if (host->slot.cd_irq >= 0) {
 		mmc_gpio_set_cd_wake(host, false);
 		disable_irq(host->slot.cd_irq);
@@ -2273,6 +2292,11 @@
 
 	host->rescan_disable = 1;
 	cancel_delayed_work_sync(&host->detect);
+}
+
+void mmc_stop_host(struct mmc_host *host)
+{
+	__mmc_stop_host(host);
 
 	/* clear pm flags now and let card drivers set them as needed */
 	host->pm_flags = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/core.h
@@ -70,6 +70,7 @@
 
 void mmc_rescan(struct work_struct *work);
 void mmc_start_host(struct mmc_host *host);
+void __mmc_stop_host(struct mmc_host *host);
 void mmc_stop_host(struct mmc_host *host);
 
 void _mmc_detect_change(struct mmc_host *host, unsigned long delay,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/host.c
@@ -80,9 +80,18 @@
 	kfree(host);
 }
 
+static int mmc_host_classdev_shutdown(struct device *dev)
+{
+	struct mmc_host *host = cls_dev_to_mmc_host(dev);
+
+	__mmc_stop_host(host);
+	return 0;
+}
+
 static struct class mmc_host_class = {
 	.name		= "mmc_host",
 	.dev_release	= mmc_host_classdev_release,
+	.shutdown_pre	= mmc_host_classdev_shutdown,
 	.pm		= MMC_HOST_CLASS_DEV_PM_OPS,
 };
 
@@ -110,13 +119,12 @@
 
 /*
  * Pause re-tuning for a small set of operations.  The pause begins after the
- * next command and after first doing re-tuning.
+ * next command.
  */
 void mmc_retune_pause(struct mmc_host *host)
 {
 	if (!host->retune_paused) {
 		host->retune_paused = 1;
-		mmc_retune_needed(host);
 		mmc_retune_hold(host);
 	}
 }
@@ -579,6 +587,16 @@
 
 EXPORT_SYMBOL(mmc_alloc_host);
 
+static int mmc_validate_host_caps(struct mmc_host *host)
+{
+	if (host->caps & MMC_CAP_SDIO_IRQ && !host->ops->enable_sdio_irq) {
+		dev_warn(host->parent, "missing ->enable_sdio_irq() ops\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 /**
  *	mmc_add_host - initialise host hardware
  *	@host: mmc host
@@ -591,8 +609,9 @@
 {
 	int err;
 
-	WARN_ON((host->caps & MMC_CAP_SDIO_IRQ) &&
-		!host->ops->enable_sdio_irq);
+	err = mmc_validate_host_caps(host);
+	if (err)
+		return err;
 
 	err = device_add(&host->class_dev);
 	if (err)
@@ -641,6 +660,7 @@
  */
 void mmc_free_host(struct mmc_host *host)
 {
+	cancel_delayed_work_sync(&host->detect);
 	mmc_pwrseq_free(host);
 	put_device(&host->class_dev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/mmc.c
@@ -1000,10 +1000,12 @@
 	static unsigned ext_csd_bits[] = {
 		EXT_CSD_BUS_WIDTH_8,
 		EXT_CSD_BUS_WIDTH_4,
+		EXT_CSD_BUS_WIDTH_1,
 	};
 	static unsigned bus_widths[] = {
 		MMC_BUS_WIDTH_8,
 		MMC_BUS_WIDTH_4,
+		MMC_BUS_WIDTH_1,
 	};
 	struct mmc_host *host = card->host;
 	unsigned idx, bus_width = 0;
@@ -1381,13 +1383,17 @@
 		goto out_err;
 	}
 
+	/*
+	 * Bump to HS timing and frequency. Some cards don't handle
+	 * SEND_STATUS reliably at the initial frequency.
+	 */
 	mmc_set_timing(host, MMC_TIMING_MMC_HS);
+	mmc_set_bus_speed(card);
+
 	err = mmc_switch_status(card, true);
 	if (err)
 		goto out_err;
 
-	mmc_set_clock(host, card->ext_csd.hs_max_dtr);
-
 	/* Switch card to DDR with strobe bit */
 	val = EXT_CSD_DDR_BUS_WIDTH_8 | EXT_CSD_BUS_WIDTH_STROBE;
 	err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
@@ -1445,7 +1451,7 @@
 static int mmc_select_hs200(struct mmc_card *card)
 {
 	struct mmc_host *host = card->host;
-	unsigned int old_timing, old_signal_voltage;
+	unsigned int old_timing, old_signal_voltage, old_clock;
 	int err = -EINVAL;
 	u8 val;
 
@@ -1476,8 +1482,17 @@
 				   false, true, MMC_CMD_RETRIES);
 		if (err)
 			goto err;
+
+		/*
+		 * Bump to HS timing and frequency. Some cards don't handle
+		 * SEND_STATUS reliably at the initial frequency.
+		 * NB: We can't move to full (HS200) speeds until after we've
+		 * successfully switched over.
+		 */
 		old_timing = host->ios.timing;
+		old_clock = host->ios.clock;
 		mmc_set_timing(host, MMC_TIMING_MMC_HS200);
+		mmc_set_clock(card->host, card->ext_csd.hs_max_dtr);
 
 		/*
 		 * For HS200, CRC errors are not a reliable way to know the
@@ -1490,8 +1505,10 @@
 		 * mmc_select_timing() assumes timing has not changed if
 		 * it is a switch error.
 		 */
-		if (err == -EBADMSG)
+		if (err == -EBADMSG) {
+			mmc_set_clock(host, old_clock);
 			mmc_set_timing(host, old_timing);
+		}
 	}
 err:
 	if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/mmc_test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/mmc_test.c
@@ -3111,13 +3111,13 @@
 	test->buffer = kzalloc(BUFFER_SIZE, GFP_KERNEL);
 #ifdef CONFIG_HIGHMEM
 	test->highmem = alloc_pages(GFP_KERNEL | __GFP_HIGHMEM, BUFFER_ORDER);
+	if (!test->highmem) {
+		count = -ENOMEM;
+		goto free_test_buffer;
+	}
 #endif
 
-#ifdef CONFIG_HIGHMEM
-	if (test->buffer && test->highmem) {
-#else
 	if (test->buffer) {
-#endif
 		mutex_lock(&mmc_test_lock);
 		mmc_test_run(test, testcase);
 		mutex_unlock(&mmc_test_lock);
@@ -3125,6 +3125,7 @@
 
 #ifdef CONFIG_HIGHMEM
 	__free_pages(test->highmem, BUFFER_ORDER);
+free_test_buffer:
 #endif
 	kfree(test->buffer);
 	kfree(test);
@@ -3181,7 +3182,8 @@
 	struct mmc_test_dbgfs_file *df;
 
 	if (card->debugfs_root)
-		debugfs_create_file(name, mode, card->debugfs_root, card, fops);
+		file = debugfs_create_file(name, mode, card->debugfs_root,
+					   card, fops);
 
 	df = kmalloc(sizeof(*df), GFP_KERNEL);
 	if (!df) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/pwrseq_sd8787.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/pwrseq_sd8787.c
@@ -28,7 +28,6 @@
 	struct mmc_pwrseq pwrseq;
 	struct gpio_desc *reset_gpio;
 	struct gpio_desc *pwrdn_gpio;
-	u32 reset_pwrdwn_delay_ms;
 };
 
 #define to_pwrseq_sd8787(p) container_of(p, struct mmc_pwrseq_sd8787, pwrseq)
@@ -39,7 +38,7 @@
 
 	gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
 
-	msleep(pwrseq->reset_pwrdwn_delay_ms);
+	msleep(300);
 	gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
 }
 
@@ -51,17 +50,37 @@
 	gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
 }
 
+static void mmc_pwrseq_wilc1000_pre_power_on(struct mmc_host *host)
+{
+	struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+	/* The pwrdn_gpio is really CHIP_EN, reset_gpio is RESETN */
+	gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
+	msleep(5);
+	gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
+}
+
+static void mmc_pwrseq_wilc1000_power_off(struct mmc_host *host)
+{
+	struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+	gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
+	gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 0);
+}
+
 static const struct mmc_pwrseq_ops mmc_pwrseq_sd8787_ops = {
 	.pre_power_on = mmc_pwrseq_sd8787_pre_power_on,
 	.power_off = mmc_pwrseq_sd8787_power_off,
 };
 
-static const u32 sd8787_delay_ms = 300;
-static const u32 wilc1000_delay_ms = 5;
+static const struct mmc_pwrseq_ops mmc_pwrseq_wilc1000_ops = {
+	.pre_power_on = mmc_pwrseq_wilc1000_pre_power_on,
+	.power_off = mmc_pwrseq_wilc1000_power_off,
+};
 
 static const struct of_device_id mmc_pwrseq_sd8787_of_match[] = {
-	{ .compatible = "mmc-pwrseq-sd8787", .data = &sd8787_delay_ms },
-	{ .compatible = "mmc-pwrseq-wilc1000", .data = &wilc1000_delay_ms },
+	{ .compatible = "mmc-pwrseq-sd8787", .data = &mmc_pwrseq_sd8787_ops },
+	{ .compatible = "mmc-pwrseq-wilc1000", .data = &mmc_pwrseq_wilc1000_ops },
 	{/* sentinel */},
 };
 MODULE_DEVICE_TABLE(of, mmc_pwrseq_sd8787_of_match);
@@ -77,7 +96,6 @@
 		return -ENOMEM;
 
 	match = of_match_node(mmc_pwrseq_sd8787_of_match, pdev->dev.of_node);
-	pwrseq->reset_pwrdwn_delay_ms = *(u32 *)match->data;
 
 	pwrseq->pwrdn_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_LOW);
 	if (IS_ERR(pwrseq->pwrdn_gpio))
@@ -88,7 +106,7 @@
 		return PTR_ERR(pwrseq->reset_gpio);
 
 	pwrseq->pwrseq.dev = dev;
-	pwrseq->pwrseq.ops = &mmc_pwrseq_sd8787_ops;
+	pwrseq->pwrseq.ops = match->data;
 	pwrseq->pwrseq.owner = THIS_MODULE;
 	platform_set_drvdata(pdev, pwrseq);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/quirks.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/quirks.h
@@ -99,6 +99,26 @@
 	MMC_FIXUP("V10016", CID_MANFID_KINGSTON, CID_OEMID_ANY, add_quirk_mmc,
 		  MMC_QUIRK_TRIM_BROKEN),
 
+	/*
+	 * Kingston EMMC04G-M627 advertises TRIM but it does not seems to
+	 * support being used to offload WRITE_ZEROES.
+	 */
+	MMC_FIXUP("M62704", CID_MANFID_KINGSTON, 0x0100, add_quirk_mmc,
+		  MMC_QUIRK_TRIM_BROKEN),
+
+	/*
+	 * Micron MTFC4GACAJCN-1M advertises TRIM but it does not seems to
+	 * support being used to offload WRITE_ZEROES.
+	 */
+	MMC_FIXUP("Q2J54A", CID_MANFID_MICRON, 0x014e, add_quirk_mmc,
+		  MMC_QUIRK_TRIM_BROKEN),
+
+	/*
+	 * Some SD cards reports discard support while they don't
+	 */
+	MMC_FIXUP(CID_NAME_ANY, CID_MANFID_SANDISK_SD, 0x5344, add_quirk_sd,
+		  MMC_QUIRK_BROKEN_SD_DISCARD),
+
 	END_FIXUP
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/regulator.c
@@ -271,3 +271,44 @@
 	return 0;
 }
 EXPORT_SYMBOL_GPL(mmc_regulator_get_supply);
+
+/**
+ * mmc_regulator_enable_vqmmc - enable VQMMC regulator for a host
+ * @mmc: the host to regulate
+ *
+ * Returns 0 or errno. Enables the regulator for vqmmc.
+ * Keeps track of the enable status for ensuring that calls to
+ * regulator_enable/disable are balanced.
+ */
+int mmc_regulator_enable_vqmmc(struct mmc_host *mmc)
+{
+	int ret = 0;
+
+	if (!IS_ERR(mmc->supply.vqmmc) && !mmc->vqmmc_enabled) {
+		ret = regulator_enable(mmc->supply.vqmmc);
+		if (ret < 0)
+			dev_err(mmc_dev(mmc), "enabling vqmmc regulator failed\n");
+		else
+			mmc->vqmmc_enabled = true;
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(mmc_regulator_enable_vqmmc);
+
+/**
+ * mmc_regulator_disable_vqmmc - disable VQMMC regulator for a host
+ * @mmc: the host to regulate
+ *
+ * Returns 0 or errno. Disables the regulator for vqmmc.
+ * Keeps track of the enable status for ensuring that calls to
+ * regulator_enable/disable are balanced.
+ */
+void mmc_regulator_disable_vqmmc(struct mmc_host *mmc)
+{
+	if (!IS_ERR(mmc->supply.vqmmc) && mmc->vqmmc_enabled) {
+		regulator_disable(mmc->supply.vqmmc);
+		mmc->vqmmc_enabled = false;
+	}
+}
+EXPORT_SYMBOL_GPL(mmc_regulator_disable_vqmmc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/sd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/sd.c
@@ -66,7 +66,7 @@
 		__res & __mask;						\
 	})
 
-#define SD_POWEROFF_NOTIFY_TIMEOUT_MS 2000
+#define SD_POWEROFF_NOTIFY_TIMEOUT_MS 1000
 #define SD_WRITE_EXTR_SINGLE_TIMEOUT_MS 1000
 
 struct sd_busy_data {
@@ -863,7 +863,8 @@
 	 * the CCS bit is set as well. We deliberately deviate from the spec in
 	 * regards to this, which allows UHS-I to be supported for SDSC cards.
 	 */
-	if (!mmc_host_is_spi(host) && rocr && (*rocr & 0x01000000)) {
+	if (!mmc_host_is_spi(host) && (ocr & SD_OCR_S18R) &&
+	    rocr && (*rocr & SD_ROCR_S18A)) {
 		err = mmc_set_uhs_voltage(host, pocr);
 		if (err == -EAGAIN) {
 			retries--;
@@ -942,16 +943,17 @@
 
 		/* Erase init depends on CSD and SSR */
 		mmc_init_erase(card);
-
-		/*
-		 * Fetch switch information from card.
-		 */
-		err = mmc_read_switch(card);
-		if (err)
-			return err;
 	}
 
 	/*
+	 * Fetch switch information from card. Note, sd3_bus_mode can change if
+	 * voltage switch outcome changes, so do this always.
+	 */
+	err = mmc_read_switch(card);
+	if (err)
+		return err;
+
+	/*
 	 * For SPI, enable CRC as appropriate.
 	 * This CRC enable is located AFTER the reading of the
 	 * card registers because some SDHC cards are not able
@@ -1250,7 +1252,7 @@
 	 */
 	err = sd_read_ext_reg(card, 0, 0, 0, 512, gen_info_buf);
 	if (err) {
-		pr_warn("%s: error %d reading general info of SD ext reg\n",
+		pr_err("%s: error %d reading general info of SD ext reg\n",
 			mmc_hostname(card->host), err);
 		goto out;
 	}
@@ -1264,7 +1266,12 @@
 	/* Number of extensions to be find. */
 	num_ext = gen_info_buf[4];
 
-	/* We support revision 0, but limit it to 512 bytes for simplicity. */
+	/*
+	 * We only support revision 0 and limit it to 512 bytes for simplicity.
+	 * No matter what, let's return zero to allow us to continue using the
+	 * card, even if we can't support the features from the SD function
+	 * extensions registers.
+	 */
 	if (rev != 0 || len > 512) {
 		pr_warn("%s: non-supported SD ext reg layout\n",
 			mmc_hostname(card->host));
@@ -1279,7 +1286,7 @@
 	for (i = 0; i < num_ext; i++) {
 		err = sd_parse_ext_reg(card, gen_info_buf, &next_ext_addr);
 		if (err) {
-			pr_warn("%s: error %d parsing SD ext reg\n",
+			pr_err("%s: error %d parsing SD ext reg\n",
 				mmc_hostname(card->host), err);
 			goto out;
 		}
@@ -1473,26 +1480,15 @@
 	if (!v18_fixup_failed && !mmc_host_is_spi(host) && mmc_host_uhs(host) &&
 	    mmc_sd_card_using_v18(card) &&
 	    host->ios.signal_voltage != MMC_SIGNAL_VOLTAGE_180) {
-		/*
-		 * Re-read switch information in case it has changed since
-		 * oldcard was initialized.
-		 */
-		if (oldcard) {
-			err = mmc_read_switch(card);
-			if (err)
-				goto free_card;
-		}
-		if (mmc_sd_card_using_v18(card)) {
-			if (mmc_host_set_uhs_voltage(host) ||
-			    mmc_sd_init_uhs_card(card)) {
-				v18_fixup_failed = true;
-				mmc_power_cycle(host, ocr);
-				if (!oldcard)
-					mmc_remove_card(card);
-				goto retry;
-			}
-			goto done;
+		if (mmc_host_set_uhs_voltage(host) ||
+		    mmc_sd_init_uhs_card(card)) {
+			v18_fixup_failed = true;
+			mmc_power_cycle(host, ocr);
+			if (!oldcard)
+				mmc_remove_card(card);
+			goto retry;
 		}
+		goto cont;
 	}
 
 	/* Initialization sequence for UHS-I cards */
@@ -1527,7 +1523,7 @@
 			mmc_set_bus_width(host, MMC_BUS_WIDTH_4);
 		}
 	}
-
+cont:
 	if (!oldcard) {
 		/* Read/parse the extension registers. */
 		err = sd_read_ext_regs(card);
@@ -1559,7 +1555,7 @@
 		err = -EINVAL;
 		goto free_card;
 	}
-done:
+
 	host->card = card;
 	return 0;
 
@@ -1663,6 +1659,12 @@
 		goto out;
 	}
 
+	/* Find out when the command is completed. */
+	err = mmc_poll_for_busy(card, SD_WRITE_EXTR_SINGLE_TIMEOUT_MS, false,
+				MMC_BUSY_EXTR_SINGLE);
+	if (err)
+		goto out;
+
 	cb_data.card = card;
 	cb_data.reg_buf = reg_buf;
 	err = __mmc_poll_for_busy(card, SD_POWEROFF_NOTIFY_TIMEOUT_MS,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/sdio.c
@@ -443,6 +443,8 @@
 	if (card->type == MMC_TYPE_SD_COMBO)
 		max_dtr = min(max_dtr, mmc_sd_get_max_clock(card));
 
+	max_dtr = min_not_zero(max_dtr, card->quirk_max_rate);
+
 	return max_dtr;
 }
 
@@ -708,6 +710,8 @@
 	if (host->ops->init_card)
 		host->ops->init_card(host, card);
 
+	card->ocr = ocr_card;
+
 	/*
 	 * If the host and card support UHS-I mode request the card
 	 * to switch to 1.8V signaling level.  No 1.8v signalling if
@@ -820,7 +824,7 @@
 			goto mismatch;
 		}
 	}
-	card->ocr = ocr_card;
+
 	mmc_fixup_device(card, sdio_fixup_methods);
 
 	if (card->type == MMC_TYPE_SD_COMBO) {
@@ -1071,8 +1075,14 @@
 		}
 		err = mmc_sdio_reinit_card(host);
 	} else if (mmc_card_wake_sdio_irq(host)) {
-		/* We may have switched to 1-bit mode during suspend */
+		/*
+		 * We may have switched to 1-bit mode during suspend,
+		 * need to hold retuning, because tuning only supprt
+		 * 4-bit mode or 8 bit mode.
+		 */
+		mmc_retune_hold_now(host);
 		err = sdio_enable_4bit_bus(host->card);
+		mmc_retune_release(host);
 	}
 
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/sdio_bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/sdio_bus.c
@@ -290,7 +290,14 @@
 {
 	struct sdio_func *func = dev_to_sdio_func(dev);
 
-	sdio_free_func_cis(func);
+	if (!(func->card->quirks & MMC_QUIRK_NONSTD_SDIO))
+		sdio_free_func_cis(func);
+
+	/*
+	 * We have now removed the link to the tuples in the
+	 * card structure, so remove the reference.
+	 */
+	put_device(&func->card->dev);
 
 	kfree(func->info);
 	kfree(func->tmpbuf);
@@ -322,6 +329,12 @@
 
 	device_initialize(&func->dev);
 
+	/*
+	 * We may link to tuples in the card structure,
+	 * we need make sure we have a reference to it.
+	 */
+	get_device(&func->card->dev);
+
 	func->dev.parent = &card->dev;
 	func->dev.bus = &sdio_bus_type;
 	func->dev.release = sdio_release_func;
@@ -375,10 +388,9 @@
  */
 void sdio_remove_func(struct sdio_func *func)
 {
-	if (!sdio_func_present(func))
-		return;
+	if (sdio_func_present(func))
+		device_del(&func->dev);
 
-	device_del(&func->dev);
 	of_node_put(func->dev.of_node);
 	put_device(&func->dev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/sdio_cis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/sdio_cis.c
@@ -404,12 +404,6 @@
 		return ret;
 
 	/*
-	 * Since we've linked to tuples in the card structure,
-	 * we must make sure we have a reference to it.
-	 */
-	get_device(&func->card->dev);
-
-	/*
 	 * Vendor/device id is optional for function CIS, so
 	 * copy it from the card structure as needed.
 	 */
@@ -434,11 +428,5 @@
 	}
 
 	func->tuples = NULL;
-
-	/*
-	 * We have now removed the link to the tuples in the
-	 * card structure, so remove the reference.
-	 */
-	put_device(&func->card->dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/core/slot-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/core/slot-gpio.c
@@ -62,11 +62,15 @@
 int mmc_gpio_get_ro(struct mmc_host *host)
 {
 	struct mmc_gpio *ctx = host->slot.handler_priv;
+	int cansleep;
 
 	if (!ctx || !ctx->ro_gpio)
 		return -ENOSYS;
 
-	return gpiod_get_value_cansleep(ctx->ro_gpio);
+	cansleep = gpiod_cansleep(ctx->ro_gpio);
+	return cansleep ?
+		gpiod_get_value_cansleep(ctx->ro_gpio) :
+		gpiod_get_value(ctx->ro_gpio);
 }
 EXPORT_SYMBOL(mmc_gpio_get_ro);
 
@@ -198,6 +202,26 @@
 }
 EXPORT_SYMBOL(mmc_gpiod_request_cd);
 
+/**
+ * mmc_gpiod_set_cd_config - set config for card-detection GPIO
+ * @host: mmc host
+ * @config: Generic pinconf config (from pinconf_to_config_packed())
+ *
+ * This can be used by mmc host drivers to fixup a card-detection GPIO's config
+ * (e.g. set PIN_CONFIG_BIAS_PULL_UP) after acquiring the GPIO descriptor
+ * through mmc_gpiod_request_cd().
+ *
+ * Returns:
+ * 0 on success, or a negative errno value on error.
+ */
+int mmc_gpiod_set_cd_config(struct mmc_host *host, unsigned long config)
+{
+	struct mmc_gpio *ctx = host->slot.handler_priv;
+
+	return gpiod_set_config(ctx->cd_gpio, config);
+}
+EXPORT_SYMBOL(mmc_gpiod_set_cd_config);
+
 bool mmc_can_gpio_cd(struct mmc_host *host)
 {
 	struct mmc_gpio *ctx = host->slot.handler_priv;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/Kconfig
@@ -523,11 +523,12 @@
 	  of Alcor Micro PCI-E card reader
 
 config MMC_AU1X
-	tristate "Alchemy AU1XX0 MMC Card Interface support"
+	bool "Alchemy AU1XX0 MMC Card Interface support"
 	depends on MIPS_ALCHEMY
+	depends on MMC=y
 	help
 	  This selects the AMD Alchemy(R) Multimedia card interface.
-	  If you have a Alchemy platform with a MMC slot, say Y or M here.
+	  If you have a Alchemy platform with a MMC slot, say Y here.
 
 	  If unsure, say N.
 
@@ -1054,14 +1055,15 @@
 
 config MMC_SDHCI_OMAP
 	tristate "TI SDHCI Controller Support"
+	depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST
 	depends on MMC_SDHCI_PLTFM && OF
 	select THERMAL
 	imply TI_SOC_THERMAL
 	select MMC_SDHCI_EXTERNAL_DMA if DMA_ENGINE
 	help
 	  This selects the Secure Digital Host Controller Interface (SDHCI)
-	  support present in TI's DRA7 SOCs. The controller supports
-	  SD/MMC/SDIO devices.
+	  support present in TI's Keystone/OMAP2+/DRA7 SOCs. The controller
+	  supports SD/MMC/SDIO devices.
 
 	  If you have a controller with this interface, say Y or M here.
 
@@ -1069,13 +1071,15 @@
 
 config MMC_SDHCI_AM654
 	tristate "Support for the SDHCI Controller in TI's AM654 SOCs"
-	depends on MMC_SDHCI_PLTFM && OF && REGMAP_MMIO
+	depends on ARCH_K3 || COMPILE_TEST
+	depends on MMC_SDHCI_PLTFM && OF
 	select MMC_SDHCI_IO_ACCESSORS
 	select MMC_CQHCI
+	select REGMAP_MMIO
 	help
 	  This selects the Secure Digital Host Controller Interface (SDHCI)
-	  support present in TI's AM654 SOCs. The controller supports
-	  SD/MMC/SDIO devices.
+	  support present in TI's AM65x/AM64x/AM62x/J721E SOCs. The controller
+	  supports SD/MMC/SDIO devices.
 
 	  If you have a controller with this interface, say Y or M here.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/alcor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/alcor.c
@@ -1114,7 +1114,10 @@
 	alcor_hw_init(host);
 
 	dev_set_drvdata(&pdev->dev, host);
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto free_host;
+
 	return 0;
 
 free_host:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/atmel-mci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/atmel-mci.c
@@ -1818,7 +1818,6 @@
 				atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
 				state = STATE_WAITING_NOTBUSY;
 			} else if (host->mrq->stop) {
-				atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
 				atmci_send_stop_cmd(host, data);
 				state = STATE_SENDING_STOP;
 			} else {
@@ -1851,8 +1850,6 @@
 				 * command to send.
 				 */
 				if (host->mrq->stop) {
-					atmci_writel(host, ATMCI_IER,
-					             ATMCI_CMDRDY);
 					atmci_send_stop_cmd(host, data);
 					state = STATE_SENDING_STOP;
 				} else {
@@ -2223,6 +2220,7 @@
 {
 	struct mmc_host			*mmc;
 	struct atmel_mci_slot		*slot;
+	int ret;
 
 	mmc = mmc_alloc_host(sizeof(struct atmel_mci_slot), &host->pdev->dev);
 	if (!mmc)
@@ -2306,11 +2304,13 @@
 
 	host->slot[id] = slot;
 	mmc_regulator_get_supply(mmc);
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret) {
+		mmc_free_host(mmc);
+		return ret;
+	}
 
 	if (gpio_is_valid(slot->detect_pin)) {
-		int ret;
-
 		timer_setup(&slot->detect_timer, atmci_detect_change, 0);
 
 		ret = request_irq(gpio_to_irq(slot->detect_pin),
@@ -2507,8 +2507,10 @@
 	/* Get MCI capabilities and set operations according to it */
 	atmci_get_cap(host);
 	ret = atmci_configure_dma(host);
-	if (ret == -EPROBE_DEFER)
+	if (ret == -EPROBE_DEFER) {
+		clk_disable_unprepare(host->mck);
 		goto err_dma_probe_defer;
+	}
 	if (ret == 0) {
 		host->prepare_data = &atmci_prepare_data_dma;
 		host->submit_data = &atmci_submit_data_dma;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/au1xmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/au1xmmc.c
@@ -1095,8 +1095,9 @@
 	if (host->platdata && host->platdata->cd_setup &&
 	    !(mmc->caps & MMC_CAP_NEEDS_POLL))
 		host->platdata->cd_setup(mmc, 0);
-out_clk:
+
 	clk_disable_unprepare(host->clk);
+out_clk:
 	clk_put(host->clk);
 out_irq:
 	free_irq(host->irq, host);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/bcm2835.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/bcm2835.c
@@ -1413,8 +1413,8 @@
 	host->max_clk = clk_get_rate(clk);
 
 	host->irq = platform_get_irq(pdev, 0);
-	if (host->irq <= 0) {
-		ret = -EINVAL;
+	if (host->irq < 0) {
+		ret = host->irq;
 		goto err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/cavium-octeon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/cavium-octeon.c
@@ -277,6 +277,7 @@
 		if (ret) {
 			dev_err(&pdev->dev, "Error populating slots\n");
 			octeon_mmc_set_shared_power(host, 0);
+			of_node_put(cn);
 			goto error;
 		}
 		i++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/cavium-thunderx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/cavium-thunderx.c
@@ -142,8 +142,10 @@
 				continue;
 
 			ret = cvm_mmc_of_slot_probe(&host->slot_pdev[i]->dev, host);
-			if (ret)
+			if (ret) {
+				of_node_put(child_node);
 				goto error;
+			}
 		}
 		i++;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/cqhci-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/cqhci-core.c
@@ -612,7 +612,7 @@
 		cqhci_writel(cq_host, 0, CQHCI_CTL);
 		mmc->cqe_on = true;
 		pr_debug("%s: cqhci: CQE on\n", mmc_hostname(mmc));
-		if (cqhci_readl(cq_host, CQHCI_CTL) && CQHCI_HALT) {
+		if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT) {
 			pr_err("%s: cqhci: CQE failed to exit halt state\n",
 			       mmc_hostname(mmc));
 		}
@@ -935,8 +935,8 @@
 	ret = cqhci_tasks_cleared(cq_host);
 
 	if (!ret)
-		pr_debug("%s: cqhci: Failed to clear tasks\n",
-			 mmc_hostname(mmc));
+		pr_warn("%s: cqhci: Failed to clear tasks\n",
+			mmc_hostname(mmc));
 
 	return ret;
 }
@@ -969,7 +969,7 @@
 	ret = cqhci_halted(cq_host);
 
 	if (!ret)
-		pr_debug("%s: cqhci: Failed to halt\n", mmc_hostname(mmc));
+		pr_warn("%s: cqhci: Failed to halt\n", mmc_hostname(mmc));
 
 	return ret;
 }
@@ -977,10 +977,10 @@
 /*
  * After halting we expect to be able to use the command line. We interpret the
  * failure to halt to mean the data lines might still be in use (and the upper
- * layers will need to send a STOP command), so we set the timeout based on a
- * generous command timeout.
+ * layers will need to send a STOP command), however failing to halt complicates
+ * the recovery, so set a timeout that would reasonably allow I/O to complete.
  */
-#define CQHCI_START_HALT_TIMEOUT	5
+#define CQHCI_START_HALT_TIMEOUT	500
 
 static void cqhci_recovery_start(struct mmc_host *mmc)
 {
@@ -1068,28 +1068,28 @@
 
 	ok = cqhci_halt(mmc, CQHCI_FINISH_HALT_TIMEOUT);
 
-	if (!cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT))
-		ok = false;
-
 	/*
 	 * The specification contradicts itself, by saying that tasks cannot be
 	 * cleared if CQHCI does not halt, but if CQHCI does not halt, it should
 	 * be disabled/re-enabled, but not to disable before clearing tasks.
 	 * Have a go anyway.
 	 */
-	if (!ok) {
-		pr_debug("%s: cqhci: disable / re-enable\n", mmc_hostname(mmc));
-		cqcfg = cqhci_readl(cq_host, CQHCI_CFG);
-		cqcfg &= ~CQHCI_ENABLE;
-		cqhci_writel(cq_host, cqcfg, CQHCI_CFG);
-		cqcfg |= CQHCI_ENABLE;
-		cqhci_writel(cq_host, cqcfg, CQHCI_CFG);
-		/* Be sure that there are no tasks */
-		ok = cqhci_halt(mmc, CQHCI_FINISH_HALT_TIMEOUT);
-		if (!cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT))
-			ok = false;
-		WARN_ON(!ok);
-	}
+	if (!cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT))
+		ok = false;
+
+	/* Disable to make sure tasks really are cleared */
+	cqcfg = cqhci_readl(cq_host, CQHCI_CFG);
+	cqcfg &= ~CQHCI_ENABLE;
+	cqhci_writel(cq_host, cqcfg, CQHCI_CFG);
+
+	cqcfg = cqhci_readl(cq_host, CQHCI_CFG);
+	cqcfg |= CQHCI_ENABLE;
+	cqhci_writel(cq_host, cqcfg, CQHCI_CFG);
+
+	cqhci_halt(mmc, CQHCI_FINISH_HALT_TIMEOUT);
+
+	if (!ok)
+		cqhci_clear_all_tasks(mmc, CQHCI_CLEAR_TIMEOUT);
 
 	cqhci_recover_mrqs(cq_host);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/davinci_mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/davinci_mmc.c
@@ -1347,7 +1347,7 @@
 	return ret;
 }
 
-static int __exit davinci_mmcsd_remove(struct platform_device *pdev)
+static void davinci_mmcsd_remove(struct platform_device *pdev)
 {
 	struct mmc_davinci_host *host = platform_get_drvdata(pdev);
 
@@ -1356,8 +1356,6 @@
 	davinci_release_dma_channels(host);
 	clk_disable_unprepare(host->clk);
 	mmc_free_host(host->mmc);
-
-	return 0;
 }
 
 #ifdef CONFIG_PM
@@ -1375,8 +1373,12 @@
 static int davinci_mmcsd_resume(struct device *dev)
 {
 	struct mmc_davinci_host *host = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(host->clk);
+	if (ret)
+		return ret;
 
-	clk_enable(host->clk);
 	mmc_davinci_reset_ctrl(host, 0);
 
 	return 0;
@@ -1400,7 +1402,7 @@
 		.of_match_table = davinci_mmc_dt_ids,
 	},
 	.probe		= davinci_mmcsd_probe,
-	.remove		= __exit_p(davinci_mmcsd_remove),
+	.remove_new	= davinci_mmcsd_remove,
 	.id_table	= davinci_mmc_devtype,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/dw_mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/dw_mmc.c
@@ -2086,7 +2086,8 @@
 				 * delayed. Allowing the transfer to take place
 				 * avoids races and keeps things simple.
 				 */
-				if (err != -ETIMEDOUT) {
+				if (err != -ETIMEDOUT &&
+				    host->dir_status == DW_MCI_RECV_STATUS) {
 					state = STATE_SENDING_DATA;
 					continue;
 				}
@@ -3245,6 +3246,10 @@
 	host->biu_clk = devm_clk_get(host->dev, "biu");
 	if (IS_ERR(host->biu_clk)) {
 		dev_dbg(host->dev, "biu clock not available\n");
+		ret = PTR_ERR(host->biu_clk);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
 	} else {
 		ret = clk_prepare_enable(host->biu_clk);
 		if (ret) {
@@ -3256,6 +3261,10 @@
 	host->ciu_clk = devm_clk_get(host->dev, "ciu");
 	if (IS_ERR(host->ciu_clk)) {
 		dev_dbg(host->dev, "ciu clock not available\n");
+		ret = PTR_ERR(host->ciu_clk);
+		if (ret == -EPROBE_DEFER)
+			goto err_clk_biu;
+
 		host->bus_hz = host->pdata->bus_hz;
 	} else {
 		ret = clk_prepare_enable(host->ciu_clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/jz4740_mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/jz4740_mmc.c
@@ -235,6 +235,26 @@
 		return PTR_ERR(host->dma_rx);
 	}
 
+	/*
+	 * Limit the maximum segment size in any SG entry according to
+	 * the parameters of the DMA engine device.
+	 */
+	if (host->dma_tx) {
+		struct device *dev = host->dma_tx->device->dev;
+		unsigned int max_seg_size = dma_get_max_seg_size(dev);
+
+		if (max_seg_size < host->mmc->max_seg_size)
+			host->mmc->max_seg_size = max_seg_size;
+	}
+
+	if (host->dma_rx) {
+		struct device *dev = host->dma_rx->device->dev;
+		unsigned int max_seg_size = dma_get_max_seg_size(dev);
+
+		if (max_seg_size < host->mmc->max_seg_size)
+			host->mmc->max_seg_size = max_seg_size;
+	}
+
 	return 0;
 }
 
@@ -1018,6 +1038,16 @@
 	mmc->ops = &jz4740_mmc_ops;
 	if (!mmc->f_max)
 		mmc->f_max = JZ_MMC_CLK_RATE;
+
+	/*
+	 * There seems to be a problem with this driver on the JZ4760 and
+	 * JZ4760B SoCs. There, when using the maximum rate supported (50 MHz),
+	 * the communication fails with many SD cards.
+	 * Until this bug is sorted out, limit the maximum rate to 24 MHz.
+	 */
+	if (host->version == JZ_MMC_JZ4760 && mmc->f_max > JZ_MMC_CLK_RATE)
+		mmc->f_max = JZ_MMC_CLK_RATE;
+
 	mmc->f_min = mmc->f_max / 128;
 	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
@@ -1103,18 +1133,18 @@
 	return 0;
 }
 
-static int __maybe_unused jz4740_mmc_suspend(struct device *dev)
+static int jz4740_mmc_suspend(struct device *dev)
 {
 	return pinctrl_pm_select_sleep_state(dev);
 }
 
-static int __maybe_unused jz4740_mmc_resume(struct device *dev)
+static int jz4740_mmc_resume(struct device *dev)
 {
 	return pinctrl_select_default_state(dev);
 }
 
-static SIMPLE_DEV_PM_OPS(jz4740_mmc_pm_ops, jz4740_mmc_suspend,
-	jz4740_mmc_resume);
+static DEFINE_SIMPLE_DEV_PM_OPS(jz4740_mmc_pm_ops, jz4740_mmc_suspend,
+				jz4740_mmc_resume);
 
 static struct platform_driver jz4740_mmc_driver = {
 	.probe = jz4740_mmc_probe,
@@ -1123,7 +1153,7 @@
 		.name = "jz4740-mmc",
 		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
 		.of_match_table = of_match_ptr(jz4740_mmc_of_match),
-		.pm = pm_ptr(&jz4740_mmc_pm_ops),
+		.pm = pm_sleep_ptr(&jz4740_mmc_pm_ops),
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/meson-gx-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/meson-gx-mmc.c
@@ -173,6 +173,8 @@
 	int irq;
 
 	bool vqmmc_enabled;
+	bool needs_pre_post_req;
+
 };
 
 #define CMD_CFG_LENGTH_MASK GENMASK(8, 0)
@@ -663,6 +665,8 @@
 	struct meson_host *host = mmc_priv(mmc);
 
 	host->cmd = NULL;
+	if (host->needs_pre_post_req)
+		meson_mmc_post_req(mmc, mrq, 0);
 	mmc_request_done(host->mmc, mrq);
 }
 
@@ -807,7 +811,6 @@
 
 	cmd_cfg |= FIELD_PREP(CMD_CFG_CMD_INDEX_MASK, cmd->opcode);
 	cmd_cfg |= CMD_CFG_OWNER;  /* owned by CPU */
-	cmd_cfg |= CMD_CFG_ERROR; /* stop in case of error */
 
 	meson_mmc_set_response_bits(cmd, &cmd_cfg);
 
@@ -880,7 +883,7 @@
 static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
 {
 	struct meson_host *host = mmc_priv(mmc);
-	bool needs_pre_post_req = mrq->data &&
+	host->needs_pre_post_req = mrq->data &&
 			!(mrq->data->host_cookie & SD_EMMC_PRE_REQ_DONE);
 
 	/*
@@ -896,22 +899,19 @@
 		}
 	}
 
-	if (needs_pre_post_req) {
+	if (host->needs_pre_post_req) {
 		meson_mmc_get_transfer_mode(mmc, mrq);
 		if (!meson_mmc_desc_chain_mode(mrq->data))
-			needs_pre_post_req = false;
+			host->needs_pre_post_req = false;
 	}
 
-	if (needs_pre_post_req)
+	if (host->needs_pre_post_req)
 		meson_mmc_pre_req(mmc, mrq);
 
 	/* Stop execution */
 	writel(0, host->regs + SD_EMMC_START);
 
 	meson_mmc_start_cmd(mmc, mrq->sbc ?: mrq->cmd);
-
-	if (needs_pre_post_req)
-		meson_mmc_post_req(mmc, mrq, 0);
 }
 
 static void meson_mmc_read_resp(struct mmc_host *mmc, struct mmc_command *cmd)
@@ -980,11 +980,8 @@
 	if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS)) {
 		if (data && !cmd->error)
 			data->bytes_xfered = data->blksz * data->blocks;
-		if (meson_mmc_bounce_buf_read(data) ||
-		    meson_mmc_get_next_command(cmd))
-			ret = IRQ_WAKE_THREAD;
-		else
-			ret = IRQ_HANDLED;
+
+		return IRQ_WAKE_THREAD;
 	}
 
 out:
@@ -996,9 +993,6 @@
 		writel(start, host->regs + SD_EMMC_START);
 	}
 
-	if (ret == IRQ_HANDLED)
-		meson_mmc_request_done(host->mmc, cmd->mrq);
-
 	return ret;
 }
 
@@ -1171,8 +1165,10 @@
 	}
 
 	ret = device_reset_optional(&pdev->dev);
-	if (ret)
-		return dev_err_probe(&pdev->dev, ret, "device reset failed\n");
+	if (ret) {
+		dev_err_probe(&pdev->dev, ret, "device reset failed\n");
+		goto free_host;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	host->regs = devm_ioremap_resource(&pdev->dev, res);
@@ -1182,8 +1178,8 @@
 	}
 
 	host->irq = platform_get_irq(pdev, 0);
-	if (host->irq <= 0) {
-		ret = -EINVAL;
+	if (host->irq < 0) {
+		ret = host->irq;
 		goto free_host;
 	}
 
@@ -1288,7 +1284,9 @@
 	}
 
 	mmc->ops = &meson_mmc_ops;
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto err_free_irq;
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/meson-mx-sdhc-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/meson-mx-sdhc-mmc.c
@@ -135,6 +135,7 @@
 				    struct mmc_command *cmd)
 {
 	struct meson_mx_sdhc_host *host = mmc_priv(mmc);
+	bool manual_stop = false;
 	u32 ictl, send;
 	int pack_len;
 
@@ -172,12 +173,27 @@
 		else
 			/* software flush: */
 			ictl |= MESON_SDHC_ICTL_DATA_XFER_OK;
+
+		/*
+		 * Mimic the logic from the vendor driver where (only)
+		 * SD_IO_RW_EXTENDED commands with more than one block set the
+		 * MESON_SDHC_MISC_MANUAL_STOP bit. This fixes the firmware
+		 * download in the brcmfmac driver for a BCM43362/1 card.
+		 * Without this sdio_memcpy_toio() (with a size of 219557
+		 * bytes) times out if MESON_SDHC_MISC_MANUAL_STOP is not set.
+		 */
+		manual_stop = cmd->data->blocks > 1 &&
+			      cmd->opcode == SD_IO_RW_EXTENDED;
 	} else {
 		pack_len = 0;
 
 		ictl |= MESON_SDHC_ICTL_RESP_OK;
 	}
 
+	regmap_update_bits(host->regmap, MESON_SDHC_MISC,
+			   MESON_SDHC_MISC_MANUAL_STOP,
+			   manual_stop ? MESON_SDHC_MISC_MANUAL_STOP : 0);
+
 	if (cmd->opcode == MMC_STOP_TRANSMISSION)
 		send |= MESON_SDHC_SEND_DATA_STOP;
 
@@ -253,7 +269,7 @@
 static int meson_mx_sdhc_set_clk(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct meson_mx_sdhc_host *host = mmc_priv(mmc);
-	u32 rx_clk_phase;
+	u32 val, rx_clk_phase;
 	int ret;
 
 	meson_mx_sdhc_disable_clks(mmc);
@@ -274,27 +290,11 @@
 		mmc->actual_clock = clk_get_rate(host->sd_clk);
 
 		/*
-		 * according to Amlogic the following latching points are
-		 * selected with empirical values, there is no (known) formula
-		 * to calculate these.
+		 * Phase 90 should work in most cases. For data transmission,
+		 * meson_mx_sdhc_execute_tuning() will find a accurate value
 		 */
-		if (mmc->actual_clock > 100000000) {
-			rx_clk_phase = 1;
-		} else if (mmc->actual_clock > 45000000) {
-			if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
-				rx_clk_phase = 15;
-			else
-				rx_clk_phase = 11;
-		} else if (mmc->actual_clock >= 25000000) {
-			rx_clk_phase = 15;
-		} else if (mmc->actual_clock > 5000000) {
-			rx_clk_phase = 23;
-		} else if (mmc->actual_clock > 1000000) {
-			rx_clk_phase = 55;
-		} else {
-			rx_clk_phase = 1061;
-		}
-
+		regmap_read(host->regmap, MESON_SDHC_CLKC, &val);
+		rx_clk_phase = FIELD_GET(MESON_SDHC_CLKC_CLK_DIV, val) / 4;
 		regmap_update_bits(host->regmap, MESON_SDHC_CLK2,
 				   MESON_SDHC_CLK2_RX_CLK_PHASE,
 				   FIELD_PREP(MESON_SDHC_CLK2_RX_CLK_PHASE,
@@ -838,6 +838,11 @@
 		goto err_disable_pclk;
 
 	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto err_disable_pclk;
+	}
+
 	ret = devm_request_threaded_irq(dev, irq, meson_mx_sdhc_irq,
 					meson_mx_sdhc_irq_thread, IRQF_ONESHOT,
 					NULL, host);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/meson-mx-sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/meson-mx-sdio.c
@@ -662,6 +662,11 @@
 	}
 
 	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto error_free_mmc;
+	}
+
 	ret = devm_request_threaded_irq(host->controller_dev, irq,
 					meson_mx_mmc_irq,
 					meson_mx_mmc_irq_thread, IRQF_ONESHOT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mmc_hsq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mmc_hsq.c
@@ -34,7 +34,7 @@
 	spin_lock_irqsave(&hsq->lock, flags);
 
 	/* Make sure we are not already running a request now */
-	if (hsq->mrq) {
+	if (hsq->mrq || hsq->recovery_halt) {
 		spin_unlock_irqrestore(&hsq->lock, flags);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mmc_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mmc_spi.c
@@ -15,7 +15,7 @@
 #include <linux/slab.h>
 #include <linux/module.h>
 #include <linux/bio.h>
-#include <linux/dma-mapping.h>
+#include <linux/dma-direction.h>
 #include <linux/crc7.h>
 #include <linux/crc-itu-t.h>
 #include <linux/scatterlist.h>
@@ -119,19 +119,14 @@
 	struct spi_transfer	status;
 	struct spi_message	readback;
 
-	/* underlying DMA-aware controller, or null */
-	struct device		*dma_dev;
-
 	/* buffer used for commands and for message "overhead" */
 	struct scratch		*data;
-	dma_addr_t		data_dma;
 
 	/* Specs say to write ones most of the time, even when the card
 	 * has no need to read its input data; and many cards won't care.
 	 * This is our source of those ones.
 	 */
 	void			*ones;
-	dma_addr_t		ones_dma;
 };
 
 
@@ -147,11 +142,8 @@
 	return spi_setup(host->spi);
 }
 
-static int
-mmc_spi_readbytes(struct mmc_spi_host *host, unsigned len)
+static int mmc_spi_readbytes(struct mmc_spi_host *host, unsigned int len)
 {
-	int status;
-
 	if (len > sizeof(*host->data)) {
 		WARN_ON(1);
 		return -EIO;
@@ -159,19 +151,7 @@
 
 	host->status.len = len;
 
-	if (host->dma_dev)
-		dma_sync_single_for_device(host->dma_dev,
-				host->data_dma, sizeof(*host->data),
-				DMA_FROM_DEVICE);
-
-	status = spi_sync_locked(host->spi, &host->readback);
-
-	if (host->dma_dev)
-		dma_sync_single_for_cpu(host->dma_dev,
-				host->data_dma, sizeof(*host->data),
-				DMA_FROM_DEVICE);
-
-	return status;
+	return spi_sync_locked(host->spi, &host->readback);
 }
 
 static int mmc_spi_skip(struct mmc_spi_host *host, unsigned long timeout,
@@ -243,10 +223,6 @@
 	u8 	leftover = 0;
 	unsigned short rotator;
 	int 	i;
-	char	tag[32];
-
-	snprintf(tag, sizeof(tag), "  ... CMD%d response SPI_%s",
-		cmd->opcode, maptype(cmd));
 
 	/* Except for data block reads, the whole response will already
 	 * be stored in the scratch buffer.  It's somewhere after the
@@ -399,8 +375,9 @@
 	}
 
 	if (value < 0)
-		dev_dbg(&host->spi->dev, "%s: resp %04x %08x\n",
-			tag, cmd->resp[0], cmd->resp[1]);
+		dev_dbg(&host->spi->dev,
+			"  ... CMD%d response SPI_%s: resp %04x %08x\n",
+			cmd->opcode, maptype(cmd), cmd->resp[0], cmd->resp[1]);
 
 	/* disable chipselect on errors and some success cases */
 	if (value >= 0 && cs_on)
@@ -506,23 +483,11 @@
 	t = &host->t;
 	memset(t, 0, sizeof(*t));
 	t->tx_buf = t->rx_buf = data->status;
-	t->tx_dma = t->rx_dma = host->data_dma;
 	t->len = cp - data->status;
 	t->cs_change = 1;
 	spi_message_add_tail(t, &host->m);
 
-	if (host->dma_dev) {
-		host->m.is_dma_mapped = 1;
-		dma_sync_single_for_device(host->dma_dev,
-				host->data_dma, sizeof(*host->data),
-				DMA_BIDIRECTIONAL);
-	}
 	status = spi_sync_locked(host->spi, &host->m);
-
-	if (host->dma_dev)
-		dma_sync_single_for_cpu(host->dma_dev,
-				host->data_dma, sizeof(*host->data),
-				DMA_BIDIRECTIONAL);
 	if (status < 0) {
 		dev_dbg(&host->spi->dev, "  ... write returned %d\n", status);
 		cmd->error = status;
@@ -540,9 +505,6 @@
  * We always provide TX data for data and CRC.  The MMC/SD protocol
  * requires us to write ones; but Linux defaults to writing zeroes;
  * so we explicitly initialize it to all ones on RX paths.
- *
- * We also handle DMA mapping, so the underlying SPI controller does
- * not need to (re)do it for each message.
  */
 static void
 mmc_spi_setup_data_message(
@@ -552,11 +514,8 @@
 {
 	struct spi_transfer	*t;
 	struct scratch		*scratch = host->data;
-	dma_addr_t		dma = host->data_dma;
 
 	spi_message_init(&host->m);
-	if (dma)
-		host->m.is_dma_mapped = 1;
 
 	/* for reads, readblock() skips 0xff bytes before finding
 	 * the token; for writes, this transfer issues that token.
@@ -570,8 +529,6 @@
 		else
 			scratch->data_token = SPI_TOKEN_SINGLE;
 		t->tx_buf = &scratch->data_token;
-		if (dma)
-			t->tx_dma = dma + offsetof(struct scratch, data_token);
 		spi_message_add_tail(t, &host->m);
 	}
 
@@ -581,7 +538,6 @@
 	t = &host->t;
 	memset(t, 0, sizeof(*t));
 	t->tx_buf = host->ones;
-	t->tx_dma = host->ones_dma;
 	/* length and actual buffer info are written later */
 	spi_message_add_tail(t, &host->m);
 
@@ -591,14 +547,9 @@
 	if (direction == DMA_TO_DEVICE) {
 		/* the actual CRC may get written later */
 		t->tx_buf = &scratch->crc_val;
-		if (dma)
-			t->tx_dma = dma + offsetof(struct scratch, crc_val);
 	} else {
 		t->tx_buf = host->ones;
-		t->tx_dma = host->ones_dma;
 		t->rx_buf = &scratch->crc_val;
-		if (dma)
-			t->rx_dma = dma + offsetof(struct scratch, crc_val);
 	}
 	spi_message_add_tail(t, &host->m);
 
@@ -621,10 +572,7 @@
 		memset(t, 0, sizeof(*t));
 		t->len = (direction == DMA_TO_DEVICE) ? sizeof(scratch->status) : 1;
 		t->tx_buf = host->ones;
-		t->tx_dma = host->ones_dma;
 		t->rx_buf = scratch->status;
-		if (dma)
-			t->rx_dma = dma + offsetof(struct scratch, status);
 		t->cs_change = 1;
 		spi_message_add_tail(t, &host->m);
 	}
@@ -653,23 +601,13 @@
 
 	if (host->mmc->use_spi_crc)
 		scratch->crc_val = cpu_to_be16(crc_itu_t(0, t->tx_buf, t->len));
-	if (host->dma_dev)
-		dma_sync_single_for_device(host->dma_dev,
-				host->data_dma, sizeof(*scratch),
-				DMA_BIDIRECTIONAL);
 
 	status = spi_sync_locked(spi, &host->m);
-
 	if (status != 0) {
 		dev_dbg(&spi->dev, "write error (%d)\n", status);
 		return status;
 	}
 
-	if (host->dma_dev)
-		dma_sync_single_for_cpu(host->dma_dev,
-				host->data_dma, sizeof(*scratch),
-				DMA_BIDIRECTIONAL);
-
 	/*
 	 * Get the transmission data-response reply.  It must follow
 	 * immediately after the data block we transferred.  This reply
@@ -718,8 +656,6 @@
 	}
 
 	t->tx_buf += t->len;
-	if (host->dma_dev)
-		t->tx_dma += t->len;
 
 	/* Return when not busy.  If we didn't collect that status yet,
 	 * we'll need some more I/O.
@@ -783,30 +719,12 @@
 	}
 	leftover = status << 1;
 
-	if (host->dma_dev) {
-		dma_sync_single_for_device(host->dma_dev,
-				host->data_dma, sizeof(*scratch),
-				DMA_BIDIRECTIONAL);
-		dma_sync_single_for_device(host->dma_dev,
-				t->rx_dma, t->len,
-				DMA_FROM_DEVICE);
-	}
-
 	status = spi_sync_locked(spi, &host->m);
 	if (status < 0) {
 		dev_dbg(&spi->dev, "read error %d\n", status);
 		return status;
 	}
 
-	if (host->dma_dev) {
-		dma_sync_single_for_cpu(host->dma_dev,
-				host->data_dma, sizeof(*scratch),
-				DMA_BIDIRECTIONAL);
-		dma_sync_single_for_cpu(host->dma_dev,
-				t->rx_dma, t->len,
-				DMA_FROM_DEVICE);
-	}
-
 	if (bitshift) {
 		/* Walk through the data and the crc and do
 		 * all the magic to get byte-aligned data.
@@ -841,8 +759,6 @@
 	}
 
 	t->rx_buf += t->len;
-	if (host->dma_dev)
-		t->rx_dma += t->len;
 
 	return 0;
 }
@@ -857,7 +773,6 @@
 		struct mmc_data *data, u32 blk_size)
 {
 	struct spi_device	*spi = host->spi;
-	struct device		*dma_dev = host->dma_dev;
 	struct spi_transfer	*t;
 	enum dma_data_direction	direction;
 	struct scatterlist	*sg;
@@ -884,31 +799,8 @@
 	 */
 	for_each_sg(data->sg, sg, data->sg_len, n_sg) {
 		int			status = 0;
-		dma_addr_t		dma_addr = 0;
 		void			*kmap_addr;
 		unsigned		length = sg->length;
-		enum dma_data_direction	dir = direction;
-
-		/* set up dma mapping for controller drivers that might
-		 * use DMA ... though they may fall back to PIO
-		 */
-		if (dma_dev) {
-			/* never invalidate whole *shared* pages ... */
-			if ((sg->offset != 0 || length != PAGE_SIZE)
-					&& dir == DMA_FROM_DEVICE)
-				dir = DMA_BIDIRECTIONAL;
-
-			dma_addr = dma_map_page(dma_dev, sg_page(sg), 0,
-						PAGE_SIZE, dir);
-			if (dma_mapping_error(dma_dev, dma_addr)) {
-				data->error = -EFAULT;
-				break;
-			}
-			if (direction == DMA_TO_DEVICE)
-				t->tx_dma = dma_addr + sg->offset;
-			else
-				t->rx_dma = dma_addr + sg->offset;
-		}
 
 		/* allow pio too; we don't allow highmem */
 		kmap_addr = kmap(sg_page(sg));
@@ -943,8 +835,6 @@
 		if (direction == DMA_FROM_DEVICE)
 			flush_dcache_page(sg_page(sg));
 		kunmap(sg_page(sg));
-		if (dma_dev)
-			dma_unmap_page(dma_dev, dma_addr, PAGE_SIZE, dir);
 
 		if (status < 0) {
 			data->error = status;
@@ -981,21 +871,9 @@
 		scratch->status[0] = SPI_TOKEN_STOP_TRAN;
 
 		host->early_status.tx_buf = host->early_status.rx_buf;
-		host->early_status.tx_dma = host->early_status.rx_dma;
 		host->early_status.len = statlen;
 
-		if (host->dma_dev)
-			dma_sync_single_for_device(host->dma_dev,
-					host->data_dma, sizeof(*scratch),
-					DMA_BIDIRECTIONAL);
-
 		tmp = spi_sync_locked(spi, &host->m);
-
-		if (host->dma_dev)
-			dma_sync_single_for_cpu(host->dma_dev,
-					host->data_dma, sizeof(*scratch),
-					DMA_BIDIRECTIONAL);
-
 		if (tmp < 0) {
 			if (!data->error)
 				data->error = tmp;
@@ -1269,52 +1147,6 @@
 	return IRQ_HANDLED;
 }
 
-#ifdef CONFIG_HAS_DMA
-static int mmc_spi_dma_alloc(struct mmc_spi_host *host)
-{
-	struct spi_device *spi = host->spi;
-	struct device *dev;
-
-	if (!spi->master->dev.parent->dma_mask)
-		return 0;
-
-	dev = spi->master->dev.parent;
-
-	host->ones_dma = dma_map_single(dev, host->ones, MMC_SPI_BLOCKSIZE,
-					DMA_TO_DEVICE);
-	if (dma_mapping_error(dev, host->ones_dma))
-		return -ENOMEM;
-
-	host->data_dma = dma_map_single(dev, host->data, sizeof(*host->data),
-					DMA_BIDIRECTIONAL);
-	if (dma_mapping_error(dev, host->data_dma)) {
-		dma_unmap_single(dev, host->ones_dma, MMC_SPI_BLOCKSIZE,
-				 DMA_TO_DEVICE);
-		return -ENOMEM;
-	}
-
-	dma_sync_single_for_cpu(dev, host->data_dma, sizeof(*host->data),
-				DMA_BIDIRECTIONAL);
-
-	host->dma_dev = dev;
-	return 0;
-}
-
-static void mmc_spi_dma_free(struct mmc_spi_host *host)
-{
-	if (!host->dma_dev)
-		return;
-
-	dma_unmap_single(host->dma_dev, host->ones_dma, MMC_SPI_BLOCKSIZE,
-			 DMA_TO_DEVICE);
-	dma_unmap_single(host->dma_dev, host->data_dma,	sizeof(*host->data),
-			 DMA_BIDIRECTIONAL);
-}
-#else
-static inline int mmc_spi_dma_alloc(struct mmc_spi_host *host) { return 0; }
-static inline void mmc_spi_dma_free(struct mmc_spi_host *host) {}
-#endif
-
 static int mmc_spi_probe(struct spi_device *spi)
 {
 	void			*ones;
@@ -1406,24 +1238,17 @@
 			host->powerup_msecs = 250;
 	}
 
-	/* preallocate dma buffers */
+	/* Preallocate buffers */
 	host->data = kmalloc(sizeof(*host->data), GFP_KERNEL);
 	if (!host->data)
 		goto fail_nobuf1;
 
-	status = mmc_spi_dma_alloc(host);
-	if (status)
-		goto fail_dma;
-
 	/* setup message for status/busy readback */
 	spi_message_init(&host->readback);
-	host->readback.is_dma_mapped = (host->dma_dev != NULL);
 
 	spi_message_add_tail(&host->status, &host->readback);
 	host->status.tx_buf = host->ones;
-	host->status.tx_dma = host->ones_dma;
 	host->status.rx_buf = &host->data->status;
-	host->status.rx_dma = host->data_dma + offsetof(struct scratch, status);
 	host->status.cs_change = 1;
 
 	/* register card detect irq */
@@ -1441,7 +1266,7 @@
 
 	status = mmc_add_host(mmc);
 	if (status != 0)
-		goto fail_add_host;
+		goto fail_glue_init;
 
 	/*
 	 * Index 0 is card detect
@@ -1449,7 +1274,7 @@
 	 */
 	status = mmc_gpiod_request_cd(mmc, NULL, 0, false, 1000);
 	if (status == -EPROBE_DEFER)
-		goto fail_add_host;
+		goto fail_gpiod_request;
 	if (!status) {
 		/*
 		 * The platform has a CD GPIO signal that may support
@@ -1464,13 +1289,12 @@
 	/* Index 1 is write protect/read only */
 	status = mmc_gpiod_request_ro(mmc, NULL, 1, 0);
 	if (status == -EPROBE_DEFER)
-		goto fail_add_host;
+		goto fail_gpiod_request;
 	if (!status)
 		has_ro = true;
 
-	dev_info(&spi->dev, "SD/MMC host %s%s%s%s%s\n",
+	dev_info(&spi->dev, "SD/MMC host %s%s%s%s\n",
 			dev_name(&mmc->class_dev),
-			host->dma_dev ? "" : ", no DMA",
 			has_ro ? "" : ", no WP",
 			(host->pdata && host->pdata->setpower)
 				? "" : ", no poweroff",
@@ -1478,11 +1302,9 @@
 				? ", cd polling" : "");
 	return 0;
 
-fail_add_host:
+fail_gpiod_request:
 	mmc_remove_host(mmc);
 fail_glue_init:
-	mmc_spi_dma_free(host);
-fail_dma:
 	kfree(host->data);
 fail_nobuf1:
 	mmc_spi_put_pdata(spi);
@@ -1504,7 +1326,6 @@
 
 	mmc_remove_host(mmc);
 
-	mmc_spi_dma_free(host);
 	kfree(host->data);
 	kfree(host->ones);
 
@@ -1514,6 +1335,12 @@
 	return 0;
 }
 
+static const struct spi_device_id mmc_spi_dev_ids[] = {
+	{ "mmc-spi-slot"},
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, mmc_spi_dev_ids);
+
 static const struct of_device_id mmc_spi_of_match_table[] = {
 	{ .compatible = "mmc-spi-slot", },
 	{},
@@ -1525,6 +1352,7 @@
 		.name =		"mmc_spi",
 		.of_match_table = mmc_spi_of_match_table,
 	},
+	.id_table =	mmc_spi_dev_ids,
 	.probe =	mmc_spi_probe,
 	.remove =	mmc_spi_remove,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mmci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mmci.c
@@ -1729,7 +1729,8 @@
 		return;
 
 	if (host->variant->busy_timeout && mmc->actual_clock)
-		max_busy_timeout = ~0UL / (mmc->actual_clock / MSEC_PER_SEC);
+		max_busy_timeout = U32_MAX / DIV_ROUND_UP(mmc->actual_clock,
+							  MSEC_PER_SEC);
 
 	mmc->max_busy_timeout = max_busy_timeout;
 }
@@ -2254,7 +2255,9 @@
 	pm_runtime_set_autosuspend_delay(&dev->dev, 50);
 	pm_runtime_use_autosuspend(&dev->dev);
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto clk_disable;
 
 	pm_runtime_put(&dev->dev);
 	return 0;
@@ -2446,6 +2449,7 @@
 	.drv		= {
 		.name	= DRIVER_NAME,
 		.pm	= &mmci_dev_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
 	},
 	.probe		= mmci_probe,
 	.remove		= mmci_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mmci_stm32_sdmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mmci_stm32_sdmmc.c
@@ -43,6 +43,9 @@
 struct sdmmc_idma {
 	dma_addr_t sg_dma;
 	void *sg_cpu;
+	dma_addr_t bounce_dma_addr;
+	void *bounce_buf;
+	bool use_bounce_buffer;
 };
 
 struct sdmmc_dlyb {
@@ -54,6 +57,8 @@
 static int sdmmc_idma_validate_data(struct mmci_host *host,
 				    struct mmc_data *data)
 {
+	struct sdmmc_idma *idma = host->dma_priv;
+	struct device *dev = mmc_dev(host->mmc);
 	struct scatterlist *sg;
 	int i;
 
@@ -61,41 +66,69 @@
 	 * idma has constraints on idmabase & idmasize for each element
 	 * excepted the last element which has no constraint on idmasize
 	 */
+	idma->use_bounce_buffer = false;
 	for_each_sg(data->sg, sg, data->sg_len - 1, i) {
-		if (!IS_ALIGNED(data->sg->offset, sizeof(u32)) ||
-		    !IS_ALIGNED(data->sg->length, SDMMC_IDMA_BURST)) {
-			dev_err(mmc_dev(host->mmc),
+		if (!IS_ALIGNED(sg->offset, sizeof(u32)) ||
+		    !IS_ALIGNED(sg->length, SDMMC_IDMA_BURST)) {
+			dev_dbg(mmc_dev(host->mmc),
 				"unaligned scatterlist: ofst:%x length:%d\n",
 				data->sg->offset, data->sg->length);
-			return -EINVAL;
+			goto use_bounce_buffer;
 		}
 	}
 
-	if (!IS_ALIGNED(data->sg->offset, sizeof(u32))) {
-		dev_err(mmc_dev(host->mmc),
+	if (!IS_ALIGNED(sg->offset, sizeof(u32))) {
+		dev_dbg(mmc_dev(host->mmc),
 			"unaligned last scatterlist: ofst:%x length:%d\n",
 			data->sg->offset, data->sg->length);
-		return -EINVAL;
+		goto use_bounce_buffer;
 	}
 
 	return 0;
+
+use_bounce_buffer:
+	if (!idma->bounce_buf) {
+		idma->bounce_buf = dmam_alloc_coherent(dev,
+						       host->mmc->max_req_size,
+						       &idma->bounce_dma_addr,
+						       GFP_KERNEL);
+		if (!idma->bounce_buf) {
+			dev_err(dev, "Unable to map allocate DMA bounce buffer.\n");
+			return -ENOMEM;
+		}
+	}
+
+	idma->use_bounce_buffer = true;
+
+	return 0;
 }
 
 static int _sdmmc_idma_prep_data(struct mmci_host *host,
 				 struct mmc_data *data)
 {
-	int n_elem;
+	struct sdmmc_idma *idma = host->dma_priv;
 
-	n_elem = dma_map_sg(mmc_dev(host->mmc),
-			    data->sg,
-			    data->sg_len,
-			    mmc_get_dma_dir(data));
+	if (idma->use_bounce_buffer) {
+		if (data->flags & MMC_DATA_WRITE) {
+			unsigned int xfer_bytes = data->blksz * data->blocks;
+
+			sg_copy_to_buffer(data->sg, data->sg_len,
+					  idma->bounce_buf, xfer_bytes);
+			dma_wmb();
+		}
+	} else {
+		int n_elem;
 
-	if (!n_elem) {
-		dev_err(mmc_dev(host->mmc), "dma_map_sg failed\n");
-		return -EINVAL;
-	}
+		n_elem = dma_map_sg(mmc_dev(host->mmc),
+				    data->sg,
+				    data->sg_len,
+				    mmc_get_dma_dir(data));
 
+		if (!n_elem) {
+			dev_err(mmc_dev(host->mmc), "dma_map_sg failed\n");
+			return -EINVAL;
+		}
+	}
 	return 0;
 }
 
@@ -112,8 +145,19 @@
 static void sdmmc_idma_unprep_data(struct mmci_host *host,
 				   struct mmc_data *data, int err)
 {
-	dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
-		     mmc_get_dma_dir(data));
+	struct sdmmc_idma *idma = host->dma_priv;
+
+	if (idma->use_bounce_buffer) {
+		if (data->flags & MMC_DATA_READ) {
+			unsigned int xfer_bytes = data->blksz * data->blocks;
+
+			sg_copy_from_buffer(data->sg, data->sg_len,
+					    idma->bounce_buf, xfer_bytes);
+		}
+	} else {
+		dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+			     mmc_get_dma_dir(data));
+	}
 }
 
 static int sdmmc_idma_setup(struct mmci_host *host)
@@ -137,6 +181,8 @@
 		host->mmc->max_segs = SDMMC_LLI_BUF_LEN /
 			sizeof(struct sdmmc_lli_desc);
 		host->mmc->max_seg_size = host->variant->stm32_idmabsize_mask;
+
+		host->mmc->max_req_size = SZ_1M;
 	} else {
 		host->mmc->max_segs = 1;
 		host->mmc->max_seg_size = host->mmc->max_req_size;
@@ -154,8 +200,18 @@
 	struct scatterlist *sg;
 	int i;
 
-	if (!host->variant->dma_lli || data->sg_len == 1) {
-		writel_relaxed(sg_dma_address(data->sg),
+	host->dma_in_progress = true;
+
+	if (!host->variant->dma_lli || data->sg_len == 1 ||
+	    idma->use_bounce_buffer) {
+		u32 dma_addr;
+
+		if (idma->use_bounce_buffer)
+			dma_addr = idma->bounce_dma_addr;
+		else
+			dma_addr = sg_dma_address(data->sg);
+
+		writel_relaxed(dma_addr,
 			       host->base + MMCI_STM32_IDMABASE0R);
 		writel_relaxed(MMCI_STM32_IDMAEN,
 			       host->base + MMCI_STM32_IDMACTRLR);
@@ -184,9 +240,30 @@
 	return 0;
 }
 
+static void sdmmc_idma_error(struct mmci_host *host)
+{
+	struct mmc_data *data = host->data;
+	struct sdmmc_idma *idma = host->dma_priv;
+
+	if (!dma_inprogress(host))
+		return;
+
+	writel_relaxed(0, host->base + MMCI_STM32_IDMACTRLR);
+	host->dma_in_progress = false;
+	data->host_cookie = 0;
+
+	if (!idma->use_bounce_buffer)
+		dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+			     mmc_get_dma_dir(data));
+}
+
 static void sdmmc_idma_finalize(struct mmci_host *host, struct mmc_data *data)
 {
+	if (!dma_inprogress(host))
+		return;
+
 	writel_relaxed(0, host->base + MMCI_STM32_IDMACTRLR);
+	host->dma_in_progress = false;
 
 	if (!data->host_cookie)
 		sdmmc_idma_unprep_data(host, data, 0);
@@ -441,6 +518,8 @@
 		return -EINVAL;
 	}
 
+	writel_relaxed(0, dlyb->base + DLYB_CR);
+
 	phase = end_of_len - max_len / 2;
 	sdmmc_dlyb_set_cfgr(dlyb, dlyb->unit, phase, false);
 
@@ -510,6 +589,7 @@
 	.dma_setup = sdmmc_idma_setup,
 	.dma_start = sdmmc_idma_start,
 	.dma_finalize = sdmmc_idma_finalize,
+	.dma_error = sdmmc_idma_error,
 	.set_clkreg = mmci_sdmmc_set_clkreg,
 	.set_pwrreg = mmci_sdmmc_set_pwrreg,
 	.busy_complete = sdmmc_busy_complete,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/moxart-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/moxart-mmc.c
@@ -111,8 +111,8 @@
 #define CLK_DIV_MASK		0x7f
 
 /* REG_BUS_WIDTH */
-#define BUS_WIDTH_8		BIT(2)
-#define BUS_WIDTH_4		BIT(1)
+#define BUS_WIDTH_4_SUPPORT	BIT(3)
+#define BUS_WIDTH_4		BIT(2)
 #define BUS_WIDTH_1		BIT(0)
 
 #define MMC_VDD_360		23
@@ -338,13 +338,7 @@
 				return;
 			}
 			for (len = 0; len < remain && len < host->fifo_width;) {
-				/* SCR data must be read in big endian. */
-				if (data->mrq->cmd->opcode == SD_APP_SEND_SCR)
-					*sgp = ioread32be(host->base +
-							  REG_DATA_WINDOW);
-				else
-					*sgp = ioread32(host->base +
-							REG_DATA_WINDOW);
+				*sgp = ioread32(host->base + REG_DATA_WINDOW);
 				sgp++;
 				len += 4;
 			}
@@ -524,9 +518,6 @@
 	case MMC_BUS_WIDTH_4:
 		writel(BUS_WIDTH_4, host->base + REG_BUS_WIDTH);
 		break;
-	case MMC_BUS_WIDTH_8:
-		writel(BUS_WIDTH_8, host->base + REG_BUS_WIDTH);
-		break;
 	default:
 		writel(BUS_WIDTH_1, host->base + REG_BUS_WIDTH);
 		break;
@@ -566,37 +557,37 @@
 	if (!mmc) {
 		dev_err(dev, "mmc_alloc_host failed\n");
 		ret = -ENOMEM;
-		goto out;
+		goto out_mmc;
 	}
 
 	ret = of_address_to_resource(node, 0, &res_mmc);
 	if (ret) {
 		dev_err(dev, "of_address_to_resource failed\n");
-		goto out;
+		goto out_mmc;
 	}
 
 	irq = irq_of_parse_and_map(node, 0);
 	if (irq <= 0) {
 		dev_err(dev, "irq_of_parse_and_map failed\n");
 		ret = -EINVAL;
-		goto out;
+		goto out_mmc;
 	}
 
 	clk = devm_clk_get(dev, NULL);
 	if (IS_ERR(clk)) {
 		ret = PTR_ERR(clk);
-		goto out;
+		goto out_mmc;
 	}
 
 	reg_mmc = devm_ioremap_resource(dev, &res_mmc);
 	if (IS_ERR(reg_mmc)) {
 		ret = PTR_ERR(reg_mmc);
-		goto out;
+		goto out_mmc;
 	}
 
 	ret = mmc_of_parse(mmc);
 	if (ret)
-		goto out;
+		goto out_mmc;
 
 	host = mmc_priv(mmc);
 	host->mmc = mmc;
@@ -621,6 +612,14 @@
 			ret = -EPROBE_DEFER;
 			goto out;
 		}
+		if (!IS_ERR(host->dma_chan_tx)) {
+			dma_release_channel(host->dma_chan_tx);
+			host->dma_chan_tx = NULL;
+		}
+		if (!IS_ERR(host->dma_chan_rx)) {
+			dma_release_channel(host->dma_chan_rx);
+			host->dma_chan_rx = NULL;
+		}
 		dev_dbg(dev, "PIO mode transfer enabled\n");
 		host->have_dma = false;
 	} else {
@@ -643,16 +642,8 @@
 		dmaengine_slave_config(host->dma_chan_rx, &cfg);
 	}
 
-	switch ((readl(host->base + REG_BUS_WIDTH) >> 3) & 3) {
-	case 1:
+	if (readl(host->base + REG_BUS_WIDTH) & BUS_WIDTH_4_SUPPORT)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
-		break;
-	case 2:
-		mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
-		break;
-	default:
-		break;
-	}
 
 	writel(0, host->base + REG_INTERRUPT_MASK);
 
@@ -668,13 +659,20 @@
 		goto out;
 
 	dev_set_drvdata(dev, mmc);
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto out;
 
 	dev_dbg(dev, "IRQ=%d, FIFO is %d bytes\n", irq, host->fifo_width);
 
 	return 0;
 
 out:
+	if (!IS_ERR_OR_NULL(host->dma_chan_tx))
+		dma_release_channel(host->dma_chan_tx);
+	if (!IS_ERR_OR_NULL(host->dma_chan_rx))
+		dma_release_channel(host->dma_chan_rx);
+out_mmc:
 	if (mmc)
 		mmc_free_host(mmc);
 	return ret;
@@ -687,17 +685,17 @@
 
 	dev_set_drvdata(&pdev->dev, NULL);
 
-	if (!IS_ERR(host->dma_chan_tx))
+	if (!IS_ERR_OR_NULL(host->dma_chan_tx))
 		dma_release_channel(host->dma_chan_tx);
-	if (!IS_ERR(host->dma_chan_rx))
+	if (!IS_ERR_OR_NULL(host->dma_chan_rx))
 		dma_release_channel(host->dma_chan_rx);
 	mmc_remove_host(mmc);
-	mmc_free_host(mmc);
 
 	writel(0, host->base + REG_INTERRUPT_MASK);
 	writel(0, host->base + REG_POWER_CONTROL);
 	writel(readl(host->base + REG_CLOCK_CONTROL) | CLK_OFF,
 	       host->base + REG_CLOCK_CONTROL);
+	mmc_free_host(mmc);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mtk-sd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mtk-sd.c
@@ -8,6 +8,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
 #include <linux/ioport.h>
 #include <linux/irq.h>
 #include <linux/of_address.h>
@@ -627,12 +628,11 @@
 	u32 val;
 
 	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_RST);
-	while (readl(host->base + MSDC_CFG) & MSDC_CFG_RST)
-		cpu_relax();
+	readl_poll_timeout_atomic(host->base + MSDC_CFG, val, !(val & MSDC_CFG_RST), 0, 0);
 
 	sdr_set_bits(host->base + MSDC_FIFOCS, MSDC_FIFOCS_CLR);
-	while (readl(host->base + MSDC_FIFOCS) & MSDC_FIFOCS_CLR)
-		cpu_relax();
+	readl_poll_timeout_atomic(host->base + MSDC_FIFOCS, val,
+				  !(val & MSDC_FIFOCS_CLR), 0, 0);
 
 	val = readl(host->base + MSDC_INT);
 	writel(val, host->base + MSDC_INT);
@@ -805,8 +805,9 @@
 	clk_disable_unprepare(host->h_clk);
 }
 
-static void msdc_ungate_clock(struct msdc_host *host)
+static int msdc_ungate_clock(struct msdc_host *host)
 {
+	u32 val;
 	int ret;
 
 	clk_prepare_enable(host->h_clk);
@@ -816,11 +817,11 @@
 	ret = clk_bulk_prepare_enable(MSDC_NR_CLOCKS, host->bulk_clks);
 	if (ret) {
 		dev_err(host->dev, "Cannot enable pclk/axi/ahb clock gates\n");
-		return;
+		return ret;
 	}
 
-	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
-		cpu_relax();
+	return readl_poll_timeout(host->base + MSDC_CFG, val,
+				  (val & MSDC_CFG_CKSTB), 1, 20000);
 }
 
 static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
@@ -831,6 +832,7 @@
 	u32 div;
 	u32 sclk;
 	u32 tune_reg = host->dev_comp->pad_tune_reg;
+	u32 val;
 
 	if (!hz) {
 		dev_dbg(host->dev, "set mclk to 0\n");
@@ -911,8 +913,7 @@
 	else
 		clk_prepare_enable(clk_get_parent(host->src_clk));
 
-	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
-		cpu_relax();
+	readl_poll_timeout(host->base + MSDC_CFG, val, (val & MSDC_CFG_CKSTB), 0, 0);
 	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
 	mmc->actual_clock = sclk;
 	host->mclk = hz;
@@ -1222,13 +1223,13 @@
 static inline bool msdc_cmd_is_ready(struct msdc_host *host,
 		struct mmc_request *mrq, struct mmc_command *cmd)
 {
-	/* The max busy time we can endure is 20ms */
-	unsigned long tmo = jiffies + msecs_to_jiffies(20);
+	u32 val;
+	int ret;
 
-	while ((readl(host->base + SDC_STS) & SDC_STS_CMDBUSY) &&
-			time_before(jiffies, tmo))
-		cpu_relax();
-	if (readl(host->base + SDC_STS) & SDC_STS_CMDBUSY) {
+	/* The max busy time we can endure is 20ms */
+	ret = readl_poll_timeout_atomic(host->base + SDC_STS, val,
+					!(val & SDC_STS_CMDBUSY), 1, 20000);
+	if (ret) {
 		dev_err(host->dev, "CMD bus busy detected\n");
 		host->error |= REQ_CMD_BUSY;
 		msdc_cmd_done(host, MSDC_INT_CMDTMO, mrq, cmd);
@@ -1236,12 +1237,10 @@
 	}
 
 	if (mmc_resp_type(cmd) == MMC_RSP_R1B || cmd->data) {
-		tmo = jiffies + msecs_to_jiffies(20);
 		/* R1B or with data, should check SDCBUSY */
-		while ((readl(host->base + SDC_STS) & SDC_STS_SDCBUSY) &&
-				time_before(jiffies, tmo))
-			cpu_relax();
-		if (readl(host->base + SDC_STS) & SDC_STS_SDCBUSY) {
+		ret = readl_poll_timeout_atomic(host->base + SDC_STS, val,
+						!(val & SDC_STS_SDCBUSY), 1, 20000);
+		if (ret) {
 			dev_err(host->dev, "Controller busy detected\n");
 			host->error |= REQ_CMD_BUSY;
 			msdc_cmd_done(host, MSDC_INT_CMDTMO, mrq, cmd);
@@ -1356,7 +1355,7 @@
 		msdc_request_done(host, mrq);
 }
 
-static bool msdc_data_xfer_done(struct msdc_host *host, u32 events,
+static void msdc_data_xfer_done(struct msdc_host *host, u32 events,
 				struct mmc_request *mrq, struct mmc_data *data)
 {
 	struct mmc_command *stop;
@@ -1366,6 +1365,8 @@
 	    (MSDC_INT_XFER_COMPL | MSDC_INT_DATCRCERR | MSDC_INT_DATTMO
 	     | MSDC_INT_DMA_BDCSERR | MSDC_INT_DMA_GPDCSERR
 	     | MSDC_INT_DMA_PROTECT);
+	u32 val;
+	int ret;
 
 	spin_lock_irqsave(&host->lock, flags);
 	done = !host->data;
@@ -1374,7 +1375,7 @@
 	spin_unlock_irqrestore(&host->lock, flags);
 
 	if (done)
-		return true;
+		return;
 	stop = data->stop;
 
 	if (check_data || (stop && stop->error)) {
@@ -1382,8 +1383,17 @@
 				readl(host->base + MSDC_DMA_CFG));
 		sdr_set_field(host->base + MSDC_DMA_CTRL, MSDC_DMA_CTRL_STOP,
 				1);
-		while (readl(host->base + MSDC_DMA_CFG) & MSDC_DMA_CFG_STS)
-			cpu_relax();
+
+		ret = readl_poll_timeout_atomic(host->base + MSDC_DMA_CTRL, val,
+						!(val & MSDC_DMA_CTRL_STOP), 1, 20000);
+		if (ret)
+			dev_dbg(host->dev, "DMA stop timed out\n");
+
+		ret = readl_poll_timeout_atomic(host->base + MSDC_DMA_CFG, val,
+						!(val & MSDC_DMA_CFG_STS), 1, 20000);
+		if (ret)
+			dev_dbg(host->dev, "DMA inactive timed out\n");
+
 		sdr_clr_bits(host->base + MSDC_INTEN, data_ints_mask);
 		dev_dbg(host->dev, "DMA stop\n");
 
@@ -1407,9 +1417,7 @@
 		}
 
 		msdc_data_xfer_next(host, mrq);
-		done = true;
 	}
-	return done;
 }
 
 static void msdc_set_buswidth(struct msdc_host *host, u32 width)
@@ -2330,15 +2338,25 @@
 static void msdc_cqe_disable(struct mmc_host *mmc, bool recovery)
 {
 	struct msdc_host *host = mmc_priv(mmc);
+	unsigned int val = 0;
 
 	/* disable cmdq irq */
 	sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INT_CMDQ);
 	/* disable busy check */
 	sdr_clr_bits(host->base + MSDC_PATCH_BIT1, MSDC_PB1_BUSY_CHECK_SEL);
 
+	val = readl(host->base + MSDC_INT);
+	writel(val, host->base + MSDC_INT);
+
 	if (recovery) {
 		sdr_set_field(host->base + MSDC_DMA_CTRL,
 			      MSDC_DMA_CTRL_STOP, 1);
+		if (WARN_ON(readl_poll_timeout(host->base + MSDC_DMA_CTRL, val,
+			!(val & MSDC_DMA_CTRL_STOP), 1, 3000)))
+			return;
+		if (WARN_ON(readl_poll_timeout(host->base + MSDC_DMA_CFG, val,
+			!(val & MSDC_DMA_CFG_STS), 1, 3000)))
+			return;
 		msdc_reset_hw(host);
 	}
 }
@@ -2437,13 +2455,11 @@
 	if (IS_ERR(host->src_clk_cg))
 		host->src_clk_cg = NULL;
 
-	host->sys_clk_cg = devm_clk_get_optional(&pdev->dev, "sys_cg");
+	/* If present, always enable for this clock gate */
+	host->sys_clk_cg = devm_clk_get_optional_enabled(&pdev->dev, "sys_cg");
 	if (IS_ERR(host->sys_clk_cg))
 		host->sys_clk_cg = NULL;
 
-	/* If present, always enable for this clock gate */
-	clk_prepare_enable(host->sys_clk_cg);
-
 	host->bulk_clks[0].id = "pclk_cg";
 	host->bulk_clks[1].id = "axi_cg";
 	host->bulk_clks[2].id = "ahb_cg";
@@ -2509,7 +2525,7 @@
 
 	host->irq = platform_get_irq(pdev, 0);
 	if (host->irq < 0) {
-		ret = -EINVAL;
+		ret = host->irq;
 		goto host_free;
 	}
 
@@ -2593,7 +2609,11 @@
 	spin_lock_init(&host->lock);
 
 	platform_set_drvdata(pdev, mmc);
-	msdc_ungate_clock(host);
+	ret = msdc_ungate_clock(host);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot ungate clocks!\n");
+		goto release_clk;
+	}
 	msdc_init_hw(host);
 
 	if (mmc->caps2 & MMC_CAP2_CQE) {
@@ -2602,14 +2622,14 @@
 					     GFP_KERNEL);
 		if (!host->cq_host) {
 			ret = -ENOMEM;
-			goto host_free;
+			goto release;
 		}
 		host->cq_host->caps |= CQHCI_TASK_DESC_SZ_128;
 		host->cq_host->mmio = host->base + 0x800;
 		host->cq_host->ops = &msdc_cmdq_ops;
 		ret = cqhci_init(host->cq_host, mmc, true);
 		if (ret)
-			goto host_free;
+			goto release;
 		mmc->max_segs = 128;
 		/* cqhci 16bit length */
 		/* 0 size, means 65536 so we don't have to -1 here */
@@ -2634,9 +2654,10 @@
 end:
 	pm_runtime_disable(host->dev);
 release:
-	platform_set_drvdata(pdev, NULL);
 	msdc_deinit_hw(host);
+release_clk:
 	msdc_gate_clock(host);
+	platform_set_drvdata(pdev, NULL);
 release_mem:
 	if (host->dma.gpd)
 		dma_free_coherent(&pdev->dev,
@@ -2752,8 +2773,12 @@
 {
 	struct mmc_host *mmc = dev_get_drvdata(dev);
 	struct msdc_host *host = mmc_priv(mmc);
+	int ret;
+
+	ret = msdc_ungate_clock(host);
+	if (ret)
+		return ret;
 
-	msdc_ungate_clock(host);
 	msdc_restore_reg(host);
 	return 0;
 }
@@ -2762,11 +2787,14 @@
 {
 	struct mmc_host *mmc = dev_get_drvdata(dev);
 	int ret;
+	u32 val;
 
 	if (mmc->caps2 & MMC_CAP2_CQE) {
 		ret = cqhci_suspend(mmc);
 		if (ret)
 			return ret;
+		val = readl(((struct msdc_host *)mmc_priv(mmc))->base + MSDC_INT);
+		writel(val, ((struct msdc_host *)mmc_priv(mmc))->base + MSDC_INT);
 	}
 
 	return pm_runtime_force_suspend(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mvsdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mvsdio.c
@@ -704,7 +704,7 @@
 	}
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
-		return -ENXIO;
+		return irq;
 
 	mmc = mmc_alloc_host(sizeof(struct mvsd_host), &pdev->dev);
 	if (!mmc) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mxcmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mxcmmc.c
@@ -1025,7 +1025,7 @@
 	mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
 	mmc->max_seg_size = mmc->max_req_size;
 
-	host->devtype = (enum mxcmci_type)of_device_get_match_data(&pdev->dev);
+	host->devtype = (uintptr_t)of_device_get_match_data(&pdev->dev);
 
 	/* adjust max_segs after devtype detection */
 	if (!is_mpc512x_mmc(host))
@@ -1143,7 +1143,9 @@
 
 	timer_setup(&host->watchdog, mxcmci_watchdog, 0);
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto out_free_dma;
 
 	return 0;
 
@@ -1183,7 +1185,6 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
 static int mxcmci_suspend(struct device *dev)
 {
 	struct mmc_host *mmc = dev_get_drvdata(dev);
@@ -1210,9 +1211,8 @@
 
 	return ret;
 }
-#endif
 
-static SIMPLE_DEV_PM_OPS(mxcmci_pm_ops, mxcmci_suspend, mxcmci_resume);
+static DEFINE_SIMPLE_DEV_PM_OPS(mxcmci_pm_ops, mxcmci_suspend, mxcmci_resume);
 
 static struct platform_driver mxcmci_driver = {
 	.probe		= mxcmci_probe,
@@ -1220,7 +1220,7 @@
 	.driver		= {
 		.name		= DRIVER_NAME,
 		.probe_type	= PROBE_PREFER_ASYNCHRONOUS,
-		.pm	= &mxcmci_pm_ops,
+		.pm	= pm_sleep_ptr(&mxcmci_pm_ops),
 		.of_match_table	= mxcmci_of_match,
 	}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/mxs-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/mxs-mmc.c
@@ -552,6 +552,11 @@
 };
 MODULE_DEVICE_TABLE(of, mxs_mmc_dt_ids);
 
+static void mxs_mmc_regulator_disable(void *regulator)
+{
+	regulator_disable(regulator);
+}
+
 static int mxs_mmc_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
@@ -591,6 +596,11 @@
 				"Failed to enable vmmc regulator: %d\n", ret);
 			goto out_mmc_free;
 		}
+
+		ret = devm_add_action_or_reset(&pdev->dev, mxs_mmc_regulator_disable,
+					       reg_vmmc);
+		if (ret)
+			goto out_mmc_free;
 	}
 
 	ssp->clk = devm_clk_get(&pdev->dev, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/omap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/omap.c
@@ -1343,7 +1343,7 @@
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
-		return -ENXIO;
+		return irq;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	host->virt_base = devm_ioremap_resource(&pdev->dev, res);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/omap_hsmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/omap_hsmmc.c
@@ -1832,9 +1832,11 @@
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	irq = platform_get_irq(pdev, 0);
-	if (res == NULL || irq < 0)
+	if (!res)
 		return -ENXIO;
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
 
 	base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(base))
@@ -1987,7 +1989,9 @@
 	if (!ret)
 		mmc->caps |= MMC_CAP_SDIO_IRQ;
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto err_irq;
 
 	if (mmc_pdata(host)->name != NULL) {
 		ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/owl-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/owl-mmc.c
@@ -638,7 +638,7 @@
 
 	owl_host->irq = platform_get_irq(pdev, 0);
 	if (owl_host->irq < 0) {
-		ret = -EINVAL;
+		ret = owl_host->irq;
 		goto err_release_channel;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/pxamci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/pxamci.c
@@ -648,7 +648,7 @@
 
 	ret = pxamci_of_init(pdev, mmc);
 	if (ret)
-		return ret;
+		goto out;
 
 	host = mmc_priv(mmc);
 	host->mmc = mmc;
@@ -672,7 +672,7 @@
 
 	ret = pxamci_init_ocr(host);
 	if (ret < 0)
-		return ret;
+		goto out;
 
 	mmc->caps = 0;
 	host->cmdat = 0;
@@ -763,7 +763,12 @@
 			dev_warn(dev, "gpio_ro and get_ro() both defined\n");
 	}
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret) {
+		if (host->pdata && host->pdata->exit)
+			host->pdata->exit(dev, mmc);
+		goto out;
+	}
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/renesas_sdhi_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/renesas_sdhi_core.c
@@ -51,9 +51,6 @@
 #define HOST_MODE_GEN3_32BIT	(HOST_MODE_GEN3_WMODE | HOST_MODE_GEN3_BUSWIDTH)
 #define HOST_MODE_GEN3_64BIT	0
 
-#define CTL_SDIF_MODE	0xe6
-#define SDIF_MODE_HS400		BIT(0)
-
 #define SDHI_VER_GEN2_SDR50	0x490c
 #define SDHI_VER_RZ_A1		0x820b
 /* very old datasheets said 0x490c for SDR104, too. They are wrong! */
@@ -382,10 +379,10 @@
 			SH_MOBILE_SDHI_SCC_TMPPORT2_HS400OSEL) |
 			sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT2));
 
-	/* Set the sampling clock selection range of HS400 mode */
 	sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DTCNTL,
 		       SH_MOBILE_SDHI_SCC_DTCNTL_TAPEN |
-		       0x4 << SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_SHIFT);
+		       sd_scc_read32(host, priv,
+				     SH_MOBILE_SDHI_SCC_DTCNTL));
 
 	/* Avoid bad TAP */
 	if (bad_taps & BIT(priv->tap_set)) {
@@ -523,7 +520,7 @@
 			 SH_MOBILE_SDHI_SCC_TMPPORT2_HS400OSEL) &
 			sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT2));
 
-	if (priv->adjust_hs400_calib_table)
+	if (priv->quirks && (priv->quirks->hs400_calib_table || priv->quirks->hs400_bad_taps))
 		renesas_sdhi_adjust_hs400_mode_disable(host);
 
 	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, CLK_CTL_SCLKEN |
@@ -550,23 +547,25 @@
 }
 
 /* only populated for TMIO_MMC_MIN_RCAR2 */
-static void renesas_sdhi_reset(struct tmio_mmc_host *host)
+static void renesas_sdhi_reset(struct tmio_mmc_host *host, bool preserve)
 {
 	struct renesas_sdhi *priv = host_to_priv(host);
 	int ret;
 	u16 val;
 
-	if (priv->rstc) {
-		reset_control_reset(priv->rstc);
-		/* Unknown why but without polling reset status, it will hang */
-		read_poll_timeout(reset_control_status, ret, ret == 0, 1, 100,
-				  false, priv->rstc);
-		/* At least SDHI_VER_GEN2_SDR50 needs manual release of reset */
-		sd_ctrl_write16(host, CTL_RESET_SD, 0x0001);
-		priv->needs_adjust_hs400 = false;
-		renesas_sdhi_set_clock(host, host->clk_cache);
-	} else if (priv->scc_ctl) {
-		renesas_sdhi_scc_reset(host, priv);
+	if (!preserve) {
+		if (priv->rstc) {
+			reset_control_reset(priv->rstc);
+			/* Unknown why but without polling reset status, it will hang */
+			read_poll_timeout(reset_control_status, ret, ret == 0, 1, 100,
+					  false, priv->rstc);
+			/* At least SDHI_VER_GEN2_SDR50 needs manual release of reset */
+			sd_ctrl_write16(host, CTL_RESET_SD, 0x0001);
+			priv->needs_adjust_hs400 = false;
+			renesas_sdhi_set_clock(host, host->clk_cache);
+		} else if (priv->scc_ctl) {
+			renesas_sdhi_scc_reset(host, priv);
+		}
 	}
 
 	if (sd_ctrl_read16(host, CTL_VERSION) >= SDHI_VER_GEN3_SD) {
@@ -673,7 +672,7 @@
 
 	/* Issue CMD19 twice for each tap */
 	for (i = 0; i < 2 * priv->tap_num; i++) {
-		int cmd_error;
+		int cmd_error = 0;
 
 		/* Set sampling clock position */
 		sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TAPSET, i % priv->tap_num);
@@ -925,6 +924,10 @@
 	if (IS_ERR(priv->clk_cd))
 		priv->clk_cd = NULL;
 
+	priv->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(priv->rstc))
+		return PTR_ERR(priv->rstc);
+
 	priv->pinctrl = devm_pinctrl_get(&pdev->dev);
 	if (!IS_ERR(priv->pinctrl)) {
 		priv->pins_default = pinctrl_lookup_state(priv->pinctrl,
@@ -972,6 +975,8 @@
 		host->sdcard_irq_setbit_mask = TMIO_STAT_ALWAYS_SET_27;
 		host->sdcard_irq_mask_all = TMIO_MASK_ALL_RCAR2;
 		host->reset = renesas_sdhi_reset;
+	} else {
+		host->sdcard_irq_mask_all = TMIO_MASK_ALL;
 	}
 
 	/* Orginally registers were 16 bit apart, could be 32 or 64 nowadays */
@@ -1013,10 +1018,6 @@
 	if (ret)
 		goto efree;
 
-	priv->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
-	if (IS_ERR(priv->rstc))
-		return PTR_ERR(priv->rstc);
-
 	ver = sd_ctrl_read16(host, CTL_VERSION);
 	/* GEN2_SDR104 is first known SDHI to use 32bit block count */
 	if (ver < SDHI_VER_GEN2_SDR104 && mmc_data->max_blk_count > U16_MAX)
@@ -1038,11 +1039,14 @@
 	if (ver >= SDHI_VER_GEN3_SD)
 		host->get_timeout_cycles = renesas_sdhi_gen3_get_cycles;
 
+	/* Check for SCC so we can reset it if needed */
+	if (of_data && of_data->scc_offset && ver >= SDHI_VER_GEN2_SDR104)
+		priv->scc_ctl = host->ctl + of_data->scc_offset;
+
 	/* Enable tuning iff we have an SCC and a supported mode */
-	if (of_data && of_data->scc_offset &&
-	    (host->mmc->caps & MMC_CAP_UHS_SDR104 ||
-	     host->mmc->caps2 & (MMC_CAP2_HS200_1_8V_SDR |
-				 MMC_CAP2_HS400_1_8V))) {
+	if (priv->scc_ctl && (host->mmc->caps & MMC_CAP_UHS_SDR104 ||
+	    host->mmc->caps2 & (MMC_CAP2_HS200_1_8V_SDR |
+				MMC_CAP2_HS400_1_8V))) {
 		const struct renesas_sdhi_scc *taps = of_data->taps;
 		bool use_4tap = priv->quirks && priv->quirks->hs400_4taps;
 		bool hit = false;
@@ -1062,7 +1066,6 @@
 		if (!hit)
 			dev_warn(&host->pdev->dev, "Unknown clock rate for tuning\n");
 
-		priv->scc_ctl = host->ctl + of_data->scc_offset;
 		host->check_retune = renesas_sdhi_check_scc_error;
 		host->ops.execute_tuning = renesas_sdhi_execute_tuning;
 		host->ops.prepare_hs400_tuning = renesas_sdhi_prepare_hs400_tuning;
@@ -1070,9 +1073,7 @@
 		host->ops.hs400_complete = renesas_sdhi_hs400_complete;
 	}
 
-	ret = tmio_mmc_host_probe(host);
-	if (ret < 0)
-		goto edisclk;
+	sd_ctrl_write32_as_16_and_16(host, CTL_IRQ_MASK, host->sdcard_irq_mask_all);
 
 	num_irqs = platform_irq_count(pdev);
 	if (num_irqs < 0) {
@@ -1099,6 +1100,10 @@
 			goto eirq;
 	}
 
+	ret = tmio_mmc_host_probe(host);
+	if (ret < 0)
+		goto edisclk;
+
 	dev_info(&pdev->dev, "%s base at %pa, max clock rate %u MHz\n",
 		 mmc_hostname(host->mmc), &res->start, host->mmc->f_max / 1000000);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/rtsx_pci_sdmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/rtsx_pci_sdmmc.c
@@ -38,10 +38,7 @@
 	bool			double_clk;
 	bool			eject;
 	bool			initial_mode;
-	int			power_state;
-#define SDMMC_POWER_ON		1
-#define SDMMC_POWER_OFF		0
-
+	int			prev_power_state;
 	int			sg_count;
 	s32			cookie;
 	int			cookie_sg_count;
@@ -905,7 +902,7 @@
 	return err;
 }
 
-static int sd_power_on(struct realtek_pci_sdmmc *host)
+static int sd_power_on(struct realtek_pci_sdmmc *host, unsigned char power_mode)
 {
 	struct rtsx_pcr *pcr = host->pcr;
 	struct mmc_host *mmc = host->mmc;
@@ -913,9 +910,14 @@
 	u32 val;
 	u8 test_mode;
 
-	if (host->power_state == SDMMC_POWER_ON)
+	if (host->prev_power_state == MMC_POWER_ON)
 		return 0;
 
+	if (host->prev_power_state == MMC_POWER_UP) {
+		rtsx_pci_write_register(pcr, SD_BUS_STAT, SD_CLK_TOGGLE_EN, 0);
+		goto finish;
+	}
+
 	msleep(100);
 
 	rtsx_pci_init_cmd(pcr);
@@ -936,10 +938,15 @@
 	if (err < 0)
 		return err;
 
+	mdelay(1);
+
 	err = rtsx_pci_write_register(pcr, CARD_OE, SD_OUTPUT_EN, SD_OUTPUT_EN);
 	if (err < 0)
 		return err;
 
+	/* send at least 74 clocks */
+	rtsx_pci_write_register(pcr, SD_BUS_STAT, SD_CLK_TOGGLE_EN, SD_CLK_TOGGLE_EN);
+
 	if (PCI_PID(pcr) == PID_5261) {
 		/*
 		 * If test mode is set switch to SD Express mandatorily,
@@ -964,7 +971,8 @@
 		}
 	}
 
-	host->power_state = SDMMC_POWER_ON;
+finish:
+	host->prev_power_state = power_mode;
 	return 0;
 }
 
@@ -973,7 +981,7 @@
 	struct rtsx_pcr *pcr = host->pcr;
 	int err;
 
-	host->power_state = SDMMC_POWER_OFF;
+	host->prev_power_state = MMC_POWER_OFF;
 
 	rtsx_pci_init_cmd(pcr);
 
@@ -999,7 +1007,7 @@
 	if (power_mode == MMC_POWER_OFF)
 		err = sd_power_off(host);
 	else
-		err = sd_power_on(host);
+		err = sd_power_on(host, power_mode);
 
 	return err;
 }
@@ -1466,6 +1474,7 @@
 	struct realtek_pci_sdmmc *host;
 	struct rtsx_pcr *pcr;
 	struct pcr_handle *handle = pdev->dev.platform_data;
+	int ret;
 
 	if (!handle)
 		return -ENXIO;
@@ -1482,10 +1491,11 @@
 
 	host = mmc_priv(mmc);
 	host->pcr = pcr;
+	mmc->ios.power_delay_ms = 5;
 	host->mmc = mmc;
 	host->pdev = pdev;
 	host->cookie = -1;
-	host->power_state = SDMMC_POWER_OFF;
+	host->prev_power_state = MMC_POWER_OFF;
 	INIT_WORK(&host->work, sd_request);
 	platform_set_drvdata(pdev, host);
 	pcr->slots[RTSX_SD_CARD].p_dev = pdev;
@@ -1495,14 +1505,20 @@
 
 	realtek_init_host(host);
 
-	if (pcr->rtd3_en) {
-		pm_runtime_set_autosuspend_delay(&pdev->dev, 5000);
-		pm_runtime_use_autosuspend(&pdev->dev);
-		pm_runtime_enable(&pdev->dev);
-	}
-
+	pm_runtime_no_callbacks(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, 200);
+	pm_runtime_mark_last_busy(&pdev->dev);
+	pm_runtime_use_autosuspend(&pdev->dev);
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret) {
+		pm_runtime_dont_use_autosuspend(&pdev->dev);
+		pm_runtime_disable(&pdev->dev);
+		mmc_free_host(mmc);
+		return ret;
+	}
 
 	return 0;
 }
@@ -1521,11 +1537,6 @@
 	pcr->slots[RTSX_SD_CARD].card_event = NULL;
 	mmc = host->mmc;
 
-	if (pcr->rtd3_en) {
-		pm_runtime_dont_use_autosuspend(&pdev->dev);
-		pm_runtime_disable(&pdev->dev);
-	}
-
 	cancel_work_sync(&host->work);
 
 	mutex_lock(&host->host_mutex);
@@ -1548,6 +1559,9 @@
 
 	flush_work(&host->work);
 
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
 	mmc_free_host(mmc);
 
 	dev_dbg(&(pdev->dev),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/rtsx_usb_sdmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/rtsx_usb_sdmmc.c
@@ -1332,6 +1332,7 @@
 #ifdef RTSX_USB_USE_LEDS_CLASS
 	int err;
 #endif
+	int ret;
 
 	ucr = usb_get_intfdata(to_usb_interface(pdev->dev.parent));
 	if (!ucr)
@@ -1368,7 +1369,15 @@
 	INIT_WORK(&host->led_work, rtsx_usb_update_led);
 
 #endif
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret) {
+#ifdef RTSX_USB_USE_LEDS_CLASS
+		led_classdev_unregister(&host->led);
+#endif
+		mmc_free_host(mmc);
+		pm_runtime_disable(&pdev->dev);
+		return ret;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-acpi.c
@@ -82,6 +82,7 @@
 enum {
 	DMI_QUIRK_RESET_SD_SIGNAL_VOLT_ON_SUSP			= BIT(0),
 	DMI_QUIRK_SD_NO_WRITE_PROTECT				= BIT(1),
+	DMI_QUIRK_SD_CD_ACTIVE_HIGH				= BIT(2),
 };
 
 static inline void *sdhci_acpi_priv(struct sdhci_acpi_host *c)
@@ -795,9 +796,22 @@
 };
 MODULE_DEVICE_TABLE(acpi, sdhci_acpi_ids);
 
+/* Please keep this list sorted alphabetically */
 static const struct dmi_system_id sdhci_acpi_quirks[] = {
 	{
 		/*
+		 * The Acer Aspire Switch 10 (SW5-012) microSD slot always
+		 * reports the card being write-protected even though microSD
+		 * cards do not have a write-protect switch at all.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire SW5-012"),
+		},
+		.driver_data = (void *)DMI_QUIRK_SD_NO_WRITE_PROTECT,
+	},
+	{
+		/*
 		 * The Lenovo Miix 320-10ICR has a bug in the _PS0 method of
 		 * the SHC1 ACPI device, this bug causes it to reprogram the
 		 * wrong LDO (DLDO3) to 1.8V if 1.8V modes are used and the
@@ -812,15 +826,23 @@
 	},
 	{
 		/*
-		 * The Acer Aspire Switch 10 (SW5-012) microSD slot always
-		 * reports the card being write-protected even though microSD
-		 * cards do not have a write-protect switch at all.
+		 * Lenovo Yoga Tablet 2 Pro 1380F/L (13" Android version) this
+		 * has broken WP reporting and an inverted CD signal.
+		 * Note this has more or less the same BIOS as the Lenovo Yoga
+		 * Tablet 2 830F/L or 1050F/L (8" and 10" Android), but unlike
+		 * the 830 / 1050 models which share the same mainboard this
+		 * model has a different mainboard and the inverted CD and
+		 * broken WP are unique to this board.
 		 */
 		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire SW5-012"),
+			DMI_MATCH(DMI_SYS_VENDOR, "Intel Corp."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "VALLEYVIEW C0 PLATFORM"),
+			DMI_MATCH(DMI_BOARD_NAME, "BYT-T FFD8"),
+			/* Full match so as to NOT match the 830/1050 BIOS */
+			DMI_MATCH(DMI_BIOS_VERSION, "BLADE_21.X64.0005.R00.1504101516"),
 		},
-		.driver_data = (void *)DMI_QUIRK_SD_NO_WRITE_PROTECT,
+		.driver_data = (void *)(DMI_QUIRK_SD_NO_WRITE_PROTECT |
+					DMI_QUIRK_SD_CD_ACTIVE_HIGH),
 	},
 	{
 		/*
@@ -833,6 +855,17 @@
 		},
 		.driver_data = (void *)DMI_QUIRK_SD_NO_WRITE_PROTECT,
 	},
+	{
+		/*
+		 * The Toshiba WT10-A's microSD slot always reports the card being
+		 * write-protected.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "TOSHIBA WT10-A"),
+		},
+		.driver_data = (void *)DMI_QUIRK_SD_NO_WRITE_PROTECT,
+	},
 	{} /* Terminating entry */
 };
 
@@ -910,7 +943,7 @@
 	host->ops	= &sdhci_acpi_ops_dflt;
 	host->irq	= platform_get_irq(pdev, 0);
 	if (host->irq < 0) {
-		err = -EINVAL;
+		err = host->irq;
 		goto err_free;
 	}
 
@@ -947,6 +980,9 @@
 	if (sdhci_acpi_flag(c, SDHCI_ACPI_SD_CD)) {
 		bool v = sdhci_acpi_flag(c, SDHCI_ACPI_SD_CD_OVERRIDE_LEVEL);
 
+		if (quirks & DMI_QUIRK_SD_CD_ACTIVE_HIGH)
+			host->mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
+
 		err = mmc_gpiod_request_cd(host->mmc, NULL, 0, v, 0);
 		if (err) {
 			if (err == -EPROBE_DEFER)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-brcmstb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-brcmstb.c
@@ -12,28 +12,57 @@
 #include <linux/bitops.h>
 #include <linux/delay.h>
 
+#include "sdhci-cqhci.h"
 #include "sdhci-pltfm.h"
 #include "cqhci.h"
 
 #define SDHCI_VENDOR 0x78
 #define  SDHCI_VENDOR_ENHANCED_STRB 0x1
+#define  SDHCI_VENDOR_GATE_SDCLK_EN 0x2
 
-#define BRCMSTB_PRIV_FLAGS_NO_64BIT		BIT(0)
-#define BRCMSTB_PRIV_FLAGS_BROKEN_TIMEOUT	BIT(1)
+#define BRCMSTB_MATCH_FLAGS_NO_64BIT		BIT(0)
+#define BRCMSTB_MATCH_FLAGS_BROKEN_TIMEOUT	BIT(1)
+#define BRCMSTB_MATCH_FLAGS_HAS_CLOCK_GATE	BIT(2)
+
+#define BRCMSTB_PRIV_FLAGS_HAS_CQE		BIT(0)
+#define BRCMSTB_PRIV_FLAGS_GATE_CLOCK		BIT(1)
 
 #define SDHCI_ARASAN_CQE_BASE_ADDR		0x200
 
 struct sdhci_brcmstb_priv {
 	void __iomem *cfg_regs;
-	bool has_cqe;
+	unsigned int flags;
+	struct clk *base_clk;
+	u32 base_freq_hz;
 };
 
 struct brcmstb_match_priv {
 	void (*hs400es)(struct mmc_host *mmc, struct mmc_ios *ios);
 	struct sdhci_ops *ops;
-	unsigned int flags;
+	const unsigned int flags;
 };
 
+static inline void enable_clock_gating(struct sdhci_host *host)
+{
+	u32 reg;
+
+	reg = sdhci_readl(host, SDHCI_VENDOR);
+	reg |= SDHCI_VENDOR_GATE_SDCLK_EN;
+	sdhci_writel(host, reg, SDHCI_VENDOR);
+}
+
+void brcmstb_reset(struct sdhci_host *host, u8 mask)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_brcmstb_priv *priv = sdhci_pltfm_priv(pltfm_host);
+
+	sdhci_and_cqhci_reset(host, mask);
+
+	/* Reset will clear this, so re-enable it */
+	if (priv->flags & BRCMSTB_PRIV_FLAGS_GATE_CLOCK)
+		enable_clock_gating(host);
+}
+
 static void sdhci_brcmstb_hs400es(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct sdhci_host *host = mmc_priv(mmc);
@@ -129,22 +158,23 @@
 static struct sdhci_ops sdhci_brcmstb_ops_7216 = {
 	.set_clock = sdhci_brcmstb_set_clock,
 	.set_bus_width = sdhci_set_bus_width,
-	.reset = sdhci_reset,
+	.reset = brcmstb_reset,
 	.set_uhs_signaling = sdhci_brcmstb_set_uhs_signaling,
 };
 
 static struct brcmstb_match_priv match_priv_7425 = {
-	.flags = BRCMSTB_PRIV_FLAGS_NO_64BIT |
-	BRCMSTB_PRIV_FLAGS_BROKEN_TIMEOUT,
+	.flags = BRCMSTB_MATCH_FLAGS_NO_64BIT |
+	BRCMSTB_MATCH_FLAGS_BROKEN_TIMEOUT,
 	.ops = &sdhci_brcmstb_ops,
 };
 
 static struct brcmstb_match_priv match_priv_7445 = {
-	.flags = BRCMSTB_PRIV_FLAGS_BROKEN_TIMEOUT,
+	.flags = BRCMSTB_MATCH_FLAGS_BROKEN_TIMEOUT,
 	.ops = &sdhci_brcmstb_ops,
 };
 
 static const struct brcmstb_match_priv match_priv_7216 = {
+	.flags = BRCMSTB_MATCH_FLAGS_HAS_CLOCK_GATE,
 	.hs400es = sdhci_brcmstb_hs400es,
 	.ops = &sdhci_brcmstb_ops_7216,
 };
@@ -176,7 +206,7 @@
 	bool dma64;
 	int ret;
 
-	if (!priv->has_cqe)
+	if ((priv->flags & BRCMSTB_PRIV_FLAGS_HAS_CQE) == 0)
 		return sdhci_add_host(host);
 
 	dev_dbg(mmc_dev(host->mmc), "CQE is enabled\n");
@@ -223,10 +253,11 @@
 	struct sdhci_pltfm_host *pltfm_host;
 	const struct of_device_id *match;
 	struct sdhci_brcmstb_priv *priv;
+	u32 actual_clock_mhz;
 	struct sdhci_host *host;
 	struct resource *iomem;
-	bool has_cqe = false;
 	struct clk *clk;
+	struct clk *base_clk = NULL;
 	int res;
 
 	match = of_match_node(sdhci_brcm_of_match, pdev->dev.of_node);
@@ -244,10 +275,6 @@
 		return res;
 
 	memset(&brcmstb_pdata, 0, sizeof(brcmstb_pdata));
-	if (device_property_read_bool(&pdev->dev, "supports-cqe")) {
-		has_cqe = true;
-		match_priv->ops->irq = sdhci_brcmstb_cqhci_irq;
-	}
 	brcmstb_pdata.ops = match_priv->ops;
 	host = sdhci_pltfm_init(pdev, &brcmstb_pdata,
 				sizeof(struct sdhci_brcmstb_priv));
@@ -258,7 +285,10 @@
 
 	pltfm_host = sdhci_priv(host);
 	priv = sdhci_pltfm_priv(pltfm_host);
-	priv->has_cqe = has_cqe;
+	if (device_property_read_bool(&pdev->dev, "supports-cqe")) {
+		priv->flags |= BRCMSTB_PRIV_FLAGS_HAS_CQE;
+		match_priv->ops->irq = sdhci_brcmstb_cqhci_irq;
+	}
 
 	/* Map in the non-standard CFG registers */
 	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
@@ -274,6 +304,14 @@
 		goto err;
 
 	/*
+	 * Automatic clock gating does not work for SD cards that may
+	 * voltage switch so only enable it for non-removable devices.
+	 */
+	if ((match_priv->flags & BRCMSTB_MATCH_FLAGS_HAS_CLOCK_GATE) &&
+	    (host->mmc->caps & MMC_CAP_NONREMOVABLE))
+		priv->flags |= BRCMSTB_PRIV_FLAGS_GATE_CLOCK;
+
+	/*
 	 * If the chip has enhanced strobe and it's enabled, add
 	 * callback
 	 */
@@ -287,16 +325,45 @@
 	 * properties through mmc_of_parse().
 	 */
 	host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
-	if (match_priv->flags & BRCMSTB_PRIV_FLAGS_NO_64BIT)
+	if (match_priv->flags & BRCMSTB_MATCH_FLAGS_NO_64BIT)
 		host->caps &= ~SDHCI_CAN_64BIT;
 	host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
 	host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 |
 			 SDHCI_SUPPORT_DDR50);
 	host->quirks |= SDHCI_QUIRK_MISSING_CAPS;
 
-	if (match_priv->flags & BRCMSTB_PRIV_FLAGS_BROKEN_TIMEOUT)
+	if (match_priv->flags & BRCMSTB_MATCH_FLAGS_BROKEN_TIMEOUT)
 		host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
 
+	/* Change the base clock frequency if the DT property exists */
+	if (device_property_read_u32(&pdev->dev, "clock-frequency",
+				     &priv->base_freq_hz) != 0)
+		goto add_host;
+
+	base_clk = devm_clk_get_optional(&pdev->dev, "sdio_freq");
+	if (IS_ERR(base_clk)) {
+		dev_warn(&pdev->dev, "Clock for \"sdio_freq\" not found\n");
+		goto add_host;
+	}
+
+	res = clk_prepare_enable(base_clk);
+	if (res)
+		goto err;
+
+	/* set improved clock rate */
+	clk_set_rate(base_clk, priv->base_freq_hz);
+	actual_clock_mhz = clk_get_rate(base_clk) / 1000000;
+
+	host->caps &= ~SDHCI_CLOCK_V3_BASE_MASK;
+	host->caps |= (actual_clock_mhz << SDHCI_CLOCK_BASE_SHIFT);
+	/* Disable presets because they are now incorrect */
+	host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
+
+	dev_dbg(&pdev->dev, "Base Clock Frequency changed to %dMHz\n",
+		actual_clock_mhz);
+	priv->base_clk = base_clk;
+
+add_host:
 	res = sdhci_brcmstb_add_host(host, priv);
 	if (res)
 		goto err;
@@ -307,6 +374,7 @@
 err:
 	sdhci_pltfm_free(pdev);
 err_clk:
+	clk_disable_unprepare(base_clk);
 	clk_disable_unprepare(clk);
 	return res;
 }
@@ -318,11 +386,61 @@
 
 MODULE_DEVICE_TABLE(of, sdhci_brcm_of_match);
 
+#ifdef CONFIG_PM_SLEEP
+static int sdhci_brcmstb_suspend(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_brcmstb_priv *priv = sdhci_pltfm_priv(pltfm_host);
+	int ret;
+
+	clk_disable_unprepare(priv->base_clk);
+	if (host->mmc->caps2 & MMC_CAP2_CQE) {
+		ret = cqhci_suspend(host->mmc);
+		if (ret)
+			return ret;
+	}
+
+	return sdhci_pltfm_suspend(dev);
+}
+
+static int sdhci_brcmstb_resume(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_brcmstb_priv *priv = sdhci_pltfm_priv(pltfm_host);
+	int ret;
+
+	ret = sdhci_pltfm_resume(dev);
+	if (!ret && priv->base_freq_hz) {
+		ret = clk_prepare_enable(priv->base_clk);
+		/*
+		 * Note: using clk_get_rate() below as clk_get_rate()
+		 * honors CLK_GET_RATE_NOCACHE attribute, but clk_set_rate()
+		 * may do implicit get_rate() calls that do not honor
+		 * CLK_GET_RATE_NOCACHE.
+		 */
+		if (!ret &&
+		    (clk_get_rate(priv->base_clk) != priv->base_freq_hz))
+			ret = clk_set_rate(priv->base_clk, priv->base_freq_hz);
+	}
+
+	if (host->mmc->caps2 & MMC_CAP2_CQE)
+		ret = cqhci_resume(host->mmc);
+
+	return ret;
+}
+#endif
+
+static const struct dev_pm_ops sdhci_brcmstb_pmops = {
+	SET_SYSTEM_SLEEP_PM_OPS(sdhci_brcmstb_suspend, sdhci_brcmstb_resume)
+};
+
 static struct platform_driver sdhci_brcmstb_driver = {
 	.driver		= {
 		.name	= "sdhci-brcmstb",
 		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
-		.pm	= &sdhci_pltfm_pmops,
+		.pm	= &sdhci_brcmstb_pmops,
 		.of_match_table = of_match_ptr(sdhci_brcm_of_match),
 	},
 	.probe		= sdhci_brcmstb_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-cqhci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-cqhci.h
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright 2022 The Chromium OS Authors
+ *
+ * Support that applies to the combination of SDHCI and CQHCI, while not
+ * expressing a dependency between the two modules.
+ */
+
+#ifndef __MMC_HOST_SDHCI_CQHCI_H__
+#define __MMC_HOST_SDHCI_CQHCI_H__
+
+#include "cqhci.h"
+#include "sdhci.h"
+
+static inline void sdhci_and_cqhci_reset(struct sdhci_host *host, u8 mask)
+{
+	if ((host->mmc->caps2 & MMC_CAP2_CQE) && (mask & SDHCI_RESET_ALL) &&
+	    host->mmc->cqe_private)
+		cqhci_deactivate(host->mmc);
+
+	sdhci_reset(host, mask);
+}
+
+#endif /* __MMC_HOST_SDHCI_CQHCI_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-esdhc-imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -25,6 +25,7 @@
 #include <linux/of_device.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/pm_runtime.h>
+#include "sdhci-cqhci.h"
 #include "sdhci-pltfm.h"
 #include "sdhci-esdhc.h"
 #include "cqhci.h"
@@ -106,6 +107,7 @@
 #define ESDHC_TUNING_START_TAP_DEFAULT	0x1
 #define ESDHC_TUNING_START_TAP_MASK	0x7f
 #define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE	(1 << 7)
+#define ESDHC_TUNING_STEP_DEFAULT	0x1
 #define ESDHC_TUNING_STEP_MASK		0x00070000
 #define ESDHC_TUNING_STEP_SHIFT		16
 
@@ -169,8 +171,8 @@
 #define ESDHC_FLAG_HS400		BIT(9)
 /*
  * The IP has errata ERR010450
- * uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't
- * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
+ * uSDHC: At 1.8V due to the I/O timing limit, for SDR mode, SD card
+ * clock can't exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
  */
 #define ESDHC_FLAG_ERR010450		BIT(10)
 /* The IP supports HS400ES mode */
@@ -300,7 +302,6 @@
 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 			| ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
-			| ESDHC_FLAG_CQHCI
 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE
 			| ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME,
 };
@@ -309,7 +310,6 @@
 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 			| ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
-			| ESDHC_FLAG_CQHCI
 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE,
 };
 
@@ -917,7 +917,8 @@
 		| ESDHC_CLOCK_MASK);
 	sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
 
-	if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) {
+	if ((imx_data->socdata->flags & ESDHC_FLAG_ERR010450) &&
+	    (!(host->quirks2 & SDHCI_QUIRK2_NO_1_8_V))) {
 		unsigned int max_clock;
 
 		max_clock = imx_data->is_ddr ? 45000000 : 150000000;
@@ -1275,7 +1276,7 @@
 
 static void esdhc_reset(struct sdhci_host *host, u8 mask)
 {
-	sdhci_reset(host, mask);
+	sdhci_and_cqhci_reset(host, mask);
 
 	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
@@ -1347,7 +1348,7 @@
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 	struct cqhci_host *cq_host = host->mmc->cqe_private;
-	int tmp;
+	u32 tmp;
 
 	if (esdhc_is_usdhc(imx_data)) {
 		/*
@@ -1400,17 +1401,24 @@
 
 		if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
 			tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
-			tmp |= ESDHC_STD_TUNING_EN |
-				ESDHC_TUNING_START_TAP_DEFAULT;
-			if (imx_data->boarddata.tuning_start_tap) {
-				tmp &= ~ESDHC_TUNING_START_TAP_MASK;
+			tmp |= ESDHC_STD_TUNING_EN;
+
+			/*
+			 * ROM code or bootloader may config the start tap
+			 * and step, unmask them first.
+			 */
+			tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK);
+			if (imx_data->boarddata.tuning_start_tap)
 				tmp |= imx_data->boarddata.tuning_start_tap;
-			}
+			else
+				tmp |= ESDHC_TUNING_START_TAP_DEFAULT;
 
 			if (imx_data->boarddata.tuning_step) {
-				tmp &= ~ESDHC_TUNING_STEP_MASK;
 				tmp |= imx_data->boarddata.tuning_step
 					<< ESDHC_TUNING_STEP_SHIFT;
+			} else {
+				tmp |= ESDHC_TUNING_STEP_DEFAULT
+					<< ESDHC_TUNING_STEP_SHIFT;
 			}
 
 			/* Disable the CMD CRC check for tuning, if not, need to
@@ -1496,7 +1504,7 @@
 	 * system resume back.
 	 */
 	cqhci_writel(cq_host, 0, CQHCI_CTL);
-	if (cqhci_readl(cq_host, CQHCI_CTL) && CQHCI_HALT)
+	if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT)
 		dev_err(mmc_dev(host->mmc),
 			"failed to exit halt state when enable CQE\n");
 
@@ -1561,6 +1569,10 @@
 	if (ret)
 		return ret;
 
+	/* HS400/HS400ES require 8 bit bus */
+	if (!(host->mmc->caps & MMC_CAP_8_BIT_DATA))
+		host->mmc->caps2 &= ~(MMC_CAP2_HS400 | MMC_CAP2_HS400_ES);
+
 	if (mmc_gpio_get_cd(host->mmc) >= 0)
 		host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-msm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-msm.c
@@ -17,6 +17,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/interconnect.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/reset.h>
 
 #include "sdhci-pltfm.h"
 #include "cqhci.h"
@@ -131,9 +132,18 @@
 /* Timeout value to avoid infinite waiting for pwr_irq */
 #define MSM_PWR_IRQ_TIMEOUT_MS 5000
 
+/* Max load for eMMC Vdd supply */
+#define MMC_VMMC_MAX_LOAD_UA	570000
+
 /* Max load for eMMC Vdd-io supply */
 #define MMC_VQMMC_MAX_LOAD_UA	325000
 
+/* Max load for SD Vdd supply */
+#define SD_VMMC_MAX_LOAD_UA	800000
+
+/* Max load for SD Vdd-io supply */
+#define SD_VQMMC_MAX_LOAD_UA	22000
+
 #define msm_host_readl(msm_host, host, offset) \
 	msm_host->var_ops->msm_readl_relaxed(host, offset)
 
@@ -1398,11 +1408,48 @@
 	return ret;
 }
 
-static int sdhci_msm_set_vmmc(struct mmc_host *mmc)
+static void msm_config_vmmc_regulator(struct mmc_host *mmc, bool hpm)
+{
+	int load;
+
+	if (!hpm)
+		load = 0;
+	else if (!mmc->card)
+		load = max(MMC_VMMC_MAX_LOAD_UA, SD_VMMC_MAX_LOAD_UA);
+	else if (mmc_card_mmc(mmc->card))
+		load = MMC_VMMC_MAX_LOAD_UA;
+	else if (mmc_card_sd(mmc->card))
+		load = SD_VMMC_MAX_LOAD_UA;
+	else
+		return;
+
+	regulator_set_load(mmc->supply.vmmc, load);
+}
+
+static void msm_config_vqmmc_regulator(struct mmc_host *mmc, bool hpm)
+{
+	int load;
+
+	if (!hpm)
+		load = 0;
+	else if (!mmc->card)
+		load = max(MMC_VQMMC_MAX_LOAD_UA, SD_VQMMC_MAX_LOAD_UA);
+	else if (mmc_card_sd(mmc->card))
+		load = SD_VQMMC_MAX_LOAD_UA;
+	else
+		return;
+
+	regulator_set_load(mmc->supply.vqmmc, load);
+}
+
+static int sdhci_msm_set_vmmc(struct sdhci_msm_host *msm_host,
+			      struct mmc_host *mmc, bool hpm)
 {
 	if (IS_ERR(mmc->supply.vmmc))
 		return 0;
 
+	msm_config_vmmc_regulator(mmc, hpm);
+
 	return mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd);
 }
 
@@ -1415,6 +1462,8 @@
 	if (msm_host->vqmmc_enabled == level)
 		return 0;
 
+	msm_config_vqmmc_regulator(mmc, level);
+
 	if (level) {
 		/* Set the IO voltage regulator to default voltage level */
 		if (msm_host->caps_0 & CORE_3_0V_SUPPORT)
@@ -1637,7 +1686,8 @@
 	}
 
 	if (pwr_state) {
-		ret = sdhci_msm_set_vmmc(mmc);
+		ret = sdhci_msm_set_vmmc(msm_host, mmc,
+					 pwr_state & REQ_BUS_ON);
 		if (!ret)
 			ret = sdhci_msm_set_vqmmc(msm_host, mmc,
 					pwr_state & REQ_BUS_ON);
@@ -2436,6 +2486,7 @@
 static const struct of_device_id sdhci_msm_dt_match[] = {
 	{.compatible = "qcom,sdhci-msm-v4", .data = &sdhci_msm_mci_var},
 	{.compatible = "qcom,sdhci-msm-v5", .data = &sdhci_msm_v5_var},
+	{.compatible = "qcom,sdm670-sdhci", .data = &sdm845_sdhci_var},
 	{.compatible = "qcom,sdm845-sdhci", .data = &sdm845_sdhci_var},
 	{.compatible = "qcom,sc7180-sdhci", .data = &sdm845_sdhci_var},
 	{},
@@ -2480,8 +2531,48 @@
 		msm_host->ddr_config = DDR_CONFIG_POR_VAL;
 
 	of_property_read_u32(node, "qcom,dll-config", &msm_host->dll_config);
+
+	if (of_device_is_compatible(node, "qcom,msm8916-sdhci"))
+		host->quirks2 |= SDHCI_QUIRK2_BROKEN_64_BIT_DMA;
 }
 
+static int sdhci_msm_gcc_reset(struct device *dev, struct sdhci_host *host)
+{
+	struct reset_control *reset;
+	int ret = 0;
+
+	reset = reset_control_get_optional_exclusive(dev, NULL);
+	if (IS_ERR(reset))
+		return dev_err_probe(dev, PTR_ERR(reset),
+				"unable to acquire core_reset\n");
+
+	if (!reset)
+		return ret;
+
+	ret = reset_control_assert(reset);
+	if (ret) {
+		reset_control_put(reset);
+		return dev_err_probe(dev, ret, "core_reset assert failed\n");
+	}
+
+	/*
+	 * The hardware requirement for delay between assert/deassert
+	 * is at least 3-4 sleep clock (32.7KHz) cycles, which comes to
+	 * ~125us (4/32768). To be on the safe side add 200us delay.
+	 */
+	usleep_range(200, 210);
+
+	ret = reset_control_deassert(reset);
+	if (ret) {
+		reset_control_put(reset);
+		return dev_err_probe(dev, ret, "core_reset deassert failed\n");
+	}
+
+	usleep_range(200, 210);
+	reset_control_put(reset);
+
+	return ret;
+}
 
 static int sdhci_msm_probe(struct platform_device *pdev)
 {
@@ -2529,6 +2620,10 @@
 
 	msm_host->saved_tuning_phase = INVALID_TUNING_PHASE;
 
+	ret = sdhci_msm_gcc_reset(&pdev->dev, host);
+	if (ret)
+		goto pltfm_free;
+
 	/* Setup SDCC bus voter clock. */
 	msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
 	if (!IS_ERR(msm_host->bus_clk)) {
@@ -2781,6 +2876,11 @@
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+	unsigned long flags;
+
+	spin_lock_irqsave(&host->lock, flags);
+	host->runtime_suspended = true;
+	spin_unlock_irqrestore(&host->lock, flags);
 
 	/* Drop the performance vote */
 	dev_pm_opp_set_rate(dev, 0);
@@ -2795,6 +2895,7 @@
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+	unsigned long flags;
 	int ret;
 
 	ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks),
@@ -2813,7 +2914,15 @@
 
 	dev_pm_opp_set_rate(dev, msm_host->clk_rate);
 
-	return sdhci_msm_ice_resume(msm_host);
+	ret = sdhci_msm_ice_resume(msm_host);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&host->lock, flags);
+	host->runtime_suspended = false;
+	spin_unlock_irqrestore(&host->lock, flags);
+
+	return ret;
 }
 
 static const struct dev_pm_ops sdhci_msm_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-of-arasan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-of-arasan.c
@@ -21,10 +21,12 @@
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
 #include <linux/regmap.h>
+#include <linux/reset.h>
 #include <linux/of.h>
 #include <linux/firmware/xlnx-zynqmp.h>
 
 #include "cqhci.h"
+#include "sdhci-cqhci.h"
 #include "sdhci-pltfm.h"
 
 #define SDHCI_ARASAN_VENDOR_REGISTER	0x78
@@ -359,7 +361,7 @@
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
 
-	sdhci_reset(host, mask);
+	sdhci_and_cqhci_reset(host, mask);
 
 	if (sdhci_arasan->quirks & SDHCI_ARASAN_QUIRK_FORCE_CDTEST) {
 		ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
@@ -1495,6 +1497,66 @@
 	return 0;
 }
 
+static int sdhci_zynqmp_set_dynamic_config(struct device *dev,
+					   struct sdhci_arasan_data *sdhci_arasan)
+{
+	struct sdhci_host *host = sdhci_arasan->host;
+	struct clk_hw *hw = &sdhci_arasan->clk_data.sdcardclk_hw;
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	const char *clk_name = clk_hw_get_name(hw);
+	u32 node_id = !strcmp(clk_name, "clk_out_sd0") ? NODE_SD_0 : NODE_SD_1;
+	struct reset_control *rstc;
+	u32 mhz;
+	int ret;
+
+	/* Obtain SDHC reset control */
+	rstc = devm_reset_control_get_optional_exclusive(dev, NULL);
+	if (IS_ERR(rstc)) {
+		dev_err(dev, "Cannot get SDHC reset.\n");
+		return PTR_ERR(rstc);
+	}
+
+	reset_control_assert(rstc);
+
+	ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_FIXED, 0);
+	if (ret)
+		return ret;
+
+	ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_EMMC_SEL,
+				      !!(host->mmc->caps & MMC_CAP_NONREMOVABLE));
+	if (ret)
+		return ret;
+
+	mhz = DIV_ROUND_CLOSEST_ULL(clk_get_rate(pltfm_host->clk), 1000000);
+	if (mhz > 100 && mhz <= 200)
+		mhz = 200;
+	else if (mhz > 50 && mhz <= 100)
+		mhz = 100;
+	else if (mhz > 25 && mhz <= 50)
+		mhz = 50;
+	else
+		mhz = 25;
+
+	ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_BASECLK, mhz);
+	if (ret)
+		return ret;
+
+	ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_8BIT,
+				      !!(host->mmc->caps & MMC_CAP_8_BIT_DATA));
+	if (ret)
+		return ret;
+
+	reset_control_deassert(rstc);
+
+	/*
+	 * Workaround: In case of eMMC, to reach the card stable state
+	 * it is taking 1msec delay after deassert the controller reset.
+	 */
+	usleep_range(1000, 1500);
+
+	return 0;
+}
+
 static int sdhci_arasan_add_host(struct sdhci_arasan_data *sdhci_arasan)
 {
 	struct sdhci_host *host = sdhci_arasan->host;
@@ -1655,6 +1717,15 @@
 		goto unreg_clk;
 	}
 
+	if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a")) {
+		ret = zynqmp_pm_is_function_supported(PM_IOCTL, IOCTL_SET_SD_CONFIG);
+		if (!ret) {
+			ret = sdhci_zynqmp_set_dynamic_config(dev, sdhci_arasan);
+			if (ret)
+				goto unreg_clk;
+		}
+	}
+
 	sdhci_arasan->phy = ERR_PTR(-ENODEV);
 	if (of_device_is_compatible(np, "arasan,sdhci-5.1")) {
 		sdhci_arasan->phy = devm_phy_get(dev, "phy_arasan");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-of-aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-of-aspeed.c
@@ -513,6 +513,7 @@
 	{ .compatible = "aspeed,ast2600-sdhci", .data = &ast2600_sdhci_pdata, },
 	{ }
 };
+MODULE_DEVICE_TABLE(of, aspeed_sdhci_of_match);
 
 static struct platform_driver aspeed_sdhci_driver = {
 	.driver		= {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-of-at91.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-of-at91.c
@@ -100,8 +100,13 @@
 static void sdhci_at91_set_uhs_signaling(struct sdhci_host *host,
 					 unsigned int timing)
 {
-	if (timing == MMC_TIMING_MMC_DDR52)
-		sdhci_writeb(host, SDMMC_MC1R_DDR, SDMMC_MC1R);
+	u8 mc1r;
+
+	if (timing == MMC_TIMING_MMC_DDR52) {
+		mc1r = sdhci_readb(host, SDMMC_MC1R);
+		mc1r |= SDMMC_MC1R_DDR;
+		sdhci_writeb(host, mc1r, SDMMC_MC1R);
+	}
 	sdhci_set_uhs_signaling(host, timing);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-of-dwcmshc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-of-dwcmshc.c
@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/reset.h>
 #include <linux/sizes.h>
 
 #include "sdhci-pltfm.h"
@@ -55,14 +56,15 @@
 #define DLL_LOCK_WO_TMOUT(x) \
 	((((x) & DWCMSHC_EMMC_DLL_LOCKED) == DWCMSHC_EMMC_DLL_LOCKED) && \
 	(((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0))
-#define RK3568_MAX_CLKS 3
+#define RK35xx_MAX_CLKS 3
 
 #define BOUNDARY_OK(addr, len) \
 	((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
 
-struct rk3568_priv {
+struct rk35xx_priv {
 	/* Rockchip specified optional clocks */
-	struct clk_bulk_data rockchip_clks[RK3568_MAX_CLKS];
+	struct clk_bulk_data rockchip_clks[RK35xx_MAX_CLKS];
+	struct reset_control *reset;
 	u8 txclk_tapnum;
 };
 
@@ -176,7 +178,7 @@
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct dwcmshc_priv *dwc_priv = sdhci_pltfm_priv(pltfm_host);
-	struct rk3568_priv *priv = dwc_priv->priv;
+	struct rk35xx_priv *priv = dwc_priv->priv;
 	u8 txclk_tapnum = DLL_TXCLK_TAPNUM_DEFAULT;
 	u32 extra, reg;
 	int err;
@@ -255,6 +257,21 @@
 	sdhci_writel(host, extra, DWCMSHC_EMMC_DLL_STRBIN);
 }
 
+static void rk35xx_sdhci_reset(struct sdhci_host *host, u8 mask)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct dwcmshc_priv *dwc_priv = sdhci_pltfm_priv(pltfm_host);
+	struct rk35xx_priv *priv = dwc_priv->priv;
+
+	if (mask & SDHCI_RESET_ALL && priv->reset) {
+		reset_control_assert(priv->reset);
+		udelay(1);
+		reset_control_deassert(priv->reset);
+	}
+
+	sdhci_reset(host, mask);
+}
+
 static const struct sdhci_ops sdhci_dwcmshc_ops = {
 	.set_clock		= sdhci_set_clock,
 	.set_bus_width		= sdhci_set_bus_width,
@@ -264,12 +281,12 @@
 	.adma_write_desc	= dwcmshc_adma_write_desc,
 };
 
-static const struct sdhci_ops sdhci_dwcmshc_rk3568_ops = {
+static const struct sdhci_ops sdhci_dwcmshc_rk35xx_ops = {
 	.set_clock		= dwcmshc_rk3568_set_clock,
 	.set_bus_width		= sdhci_set_bus_width,
 	.set_uhs_signaling	= dwcmshc_set_uhs_signaling,
 	.get_max_clock		= sdhci_pltfm_clk_get_max_clock,
-	.reset			= sdhci_reset,
+	.reset			= rk35xx_sdhci_reset,
 	.adma_write_desc	= dwcmshc_adma_write_desc,
 };
 
@@ -279,30 +296,46 @@
 	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
 };
 
-static const struct sdhci_pltfm_data sdhci_dwcmshc_rk3568_pdata = {
-	.ops = &sdhci_dwcmshc_rk3568_ops,
+#ifdef CONFIG_ACPI
+static const struct sdhci_pltfm_data sdhci_dwcmshc_bf3_pdata = {
+	.ops = &sdhci_dwcmshc_ops,
+	.quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
+		   SDHCI_QUIRK2_ACMD23_BROKEN,
+};
+#endif
+
+static const struct sdhci_pltfm_data sdhci_dwcmshc_rk35xx_pdata = {
+	.ops = &sdhci_dwcmshc_rk35xx_ops,
 	.quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
 		  SDHCI_QUIRK_BROKEN_TIMEOUT_VAL,
 	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
 		   SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN,
 };
 
-static int dwcmshc_rk3568_init(struct sdhci_host *host, struct dwcmshc_priv *dwc_priv)
+static int dwcmshc_rk35xx_init(struct sdhci_host *host, struct dwcmshc_priv *dwc_priv)
 {
 	int err;
-	struct rk3568_priv *priv = dwc_priv->priv;
+	struct rk35xx_priv *priv = dwc_priv->priv;
+
+	priv->reset = devm_reset_control_array_get_optional_exclusive(mmc_dev(host->mmc));
+	if (IS_ERR(priv->reset)) {
+		err = PTR_ERR(priv->reset);
+		dev_err(mmc_dev(host->mmc), "failed to get reset control %d\n", err);
+		return err;
+	}
 
 	priv->rockchip_clks[0].id = "axi";
 	priv->rockchip_clks[1].id = "block";
 	priv->rockchip_clks[2].id = "timer";
-	err = devm_clk_bulk_get_optional(mmc_dev(host->mmc), RK3568_MAX_CLKS,
+	err = devm_clk_bulk_get_optional(mmc_dev(host->mmc), RK35xx_MAX_CLKS,
 					 priv->rockchip_clks);
 	if (err) {
 		dev_err(mmc_dev(host->mmc), "failed to get clocks %d\n", err);
 		return err;
 	}
 
-	err = clk_bulk_prepare_enable(RK3568_MAX_CLKS, priv->rockchip_clks);
+	err = clk_bulk_prepare_enable(RK35xx_MAX_CLKS, priv->rockchip_clks);
 	if (err) {
 		dev_err(mmc_dev(host->mmc), "failed to enable clocks %d\n", err);
 		return err;
@@ -324,7 +357,7 @@
 static const struct of_device_id sdhci_dwcmshc_dt_ids[] = {
 	{
 		.compatible = "rockchip,rk3568-dwcmshc",
-		.data = &sdhci_dwcmshc_rk3568_pdata,
+		.data = &sdhci_dwcmshc_rk35xx_pdata,
 	},
 	{
 		.compatible = "snps,dwcmshc-sdhci",
@@ -336,7 +369,10 @@
 
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id sdhci_dwcmshc_acpi_ids[] = {
-	{ .id = "MLNXBF30" },
+	{
+		.id = "MLNXBF30",
+		.driver_data = (kernel_ulong_t)&sdhci_dwcmshc_bf3_pdata,
+	},
 	{}
 };
 #endif
@@ -347,12 +383,12 @@
 	struct sdhci_pltfm_host *pltfm_host;
 	struct sdhci_host *host;
 	struct dwcmshc_priv *priv;
-	struct rk3568_priv *rk_priv = NULL;
+	struct rk35xx_priv *rk_priv = NULL;
 	const struct sdhci_pltfm_data *pltfm_data;
 	int err;
 	u32 extra;
 
-	pltfm_data = of_device_get_match_data(&pdev->dev);
+	pltfm_data = device_get_match_data(&pdev->dev);
 	if (!pltfm_data) {
 		dev_err(&pdev->dev, "Error: No device match data found\n");
 		return -ENODEV;
@@ -402,8 +438,8 @@
 	host->mmc_host_ops.request = dwcmshc_request;
 	host->mmc_host_ops.hs400_enhanced_strobe = dwcmshc_hs400_enhanced_strobe;
 
-	if (pltfm_data == &sdhci_dwcmshc_rk3568_pdata) {
-		rk_priv = devm_kzalloc(&pdev->dev, sizeof(struct rk3568_priv), GFP_KERNEL);
+	if (pltfm_data == &sdhci_dwcmshc_rk35xx_pdata) {
+		rk_priv = devm_kzalloc(&pdev->dev, sizeof(struct rk35xx_priv), GFP_KERNEL);
 		if (!rk_priv) {
 			err = -ENOMEM;
 			goto err_clk;
@@ -411,7 +447,7 @@
 
 		priv->priv = rk_priv;
 
-		err = dwcmshc_rk3568_init(host, priv);
+		err = dwcmshc_rk35xx_init(host, priv);
 		if (err)
 			goto err_clk;
 	}
@@ -428,7 +464,7 @@
 	clk_disable_unprepare(pltfm_host->clk);
 	clk_disable_unprepare(priv->bus_clk);
 	if (rk_priv)
-		clk_bulk_disable_unprepare(RK3568_MAX_CLKS,
+		clk_bulk_disable_unprepare(RK35xx_MAX_CLKS,
 					   rk_priv->rockchip_clks);
 free_pltfm:
 	sdhci_pltfm_free(pdev);
@@ -440,14 +476,14 @@
 	struct sdhci_host *host = platform_get_drvdata(pdev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	struct rk3568_priv *rk_priv = priv->priv;
+	struct rk35xx_priv *rk_priv = priv->priv;
 
 	sdhci_remove_host(host, 0);
 
 	clk_disable_unprepare(pltfm_host->clk);
 	clk_disable_unprepare(priv->bus_clk);
 	if (rk_priv)
-		clk_bulk_disable_unprepare(RK3568_MAX_CLKS,
+		clk_bulk_disable_unprepare(RK35xx_MAX_CLKS,
 					   rk_priv->rockchip_clks);
 	sdhci_pltfm_free(pdev);
 
@@ -460,7 +496,7 @@
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	struct rk3568_priv *rk_priv = priv->priv;
+	struct rk35xx_priv *rk_priv = priv->priv;
 	int ret;
 
 	ret = sdhci_suspend_host(host);
@@ -472,7 +508,7 @@
 		clk_disable_unprepare(priv->bus_clk);
 
 	if (rk_priv)
-		clk_bulk_disable_unprepare(RK3568_MAX_CLKS,
+		clk_bulk_disable_unprepare(RK35xx_MAX_CLKS,
 					   rk_priv->rockchip_clks);
 
 	return ret;
@@ -483,7 +519,7 @@
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	struct rk3568_priv *rk_priv = priv->priv;
+	struct rk35xx_priv *rk_priv = priv->priv;
 	int ret;
 
 	ret = clk_prepare_enable(pltfm_host->clk);
@@ -497,7 +533,7 @@
 	}
 
 	if (rk_priv) {
-		ret = clk_bulk_prepare_enable(RK3568_MAX_CLKS,
+		ret = clk_bulk_prepare_enable(RK35xx_MAX_CLKS,
 					      rk_priv->rockchip_clks);
 		if (ret)
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-of-esdhc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-of-esdhc.c
@@ -126,6 +126,7 @@
 			return ret;
 		}
 	}
+
 	/*
 	 * The DAT[3:0] line signal levels and the CMD line signal level are
 	 * not compatible with standard SDHC register. The line signal levels
@@ -137,6 +138,16 @@
 		ret = value & 0x000fffff;
 		ret |= (value >> 4) & SDHCI_DATA_LVL_MASK;
 		ret |= (value << 1) & SDHCI_CMD_LVL;
+
+		/*
+		 * Some controllers have unreliable Data Line Active
+		 * bit for commands with busy signal. This affects
+		 * Command Inhibit (data) bit. Just ignore it since
+		 * MMC core driver has already polled card status
+		 * with CMD13 after any command with busy siganl.
+		 */
+		if (esdhc->quirk_ignore_data_inhibit)
+			ret &= ~SDHCI_DATA_INHIBIT;
 		return ret;
 	}
 
@@ -151,19 +162,6 @@
 		return ret;
 	}
 
-	/*
-	 * Some controllers have unreliable Data Line Active
-	 * bit for commands with busy signal. This affects
-	 * Command Inhibit (data) bit. Just ignore it since
-	 * MMC core driver has already polled card status
-	 * with CMD13 after any command with busy siganl.
-	 */
-	if ((spec_reg == SDHCI_PRESENT_STATE) &&
-	(esdhc->quirk_ignore_data_inhibit == true)) {
-		ret = value & ~SDHCI_DATA_INHIBIT;
-		return ret;
-	}
-
 	ret = value;
 	return ret;
 }
@@ -524,12 +522,16 @@
 
 static int esdhc_of_enable_dma(struct sdhci_host *host)
 {
+	int ret;
 	u32 value;
 	struct device *dev = mmc_dev(host->mmc);
 
 	if (of_device_is_compatible(dev->of_node, "fsl,ls1043a-esdhc") ||
-	    of_device_is_compatible(dev->of_node, "fsl,ls1046a-esdhc"))
-		dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40));
+	    of_device_is_compatible(dev->of_node, "fsl,ls1046a-esdhc")) {
+		ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40));
+		if (ret)
+			return ret;
+	}
 
 	value = sdhci_readl(host, ESDHC_DMA_SYSCTL);
 
@@ -900,6 +902,7 @@
 		scfg_node = of_find_matching_node(NULL, scfg_device_ids);
 		if (scfg_node)
 			scfg_base = of_iomap(scfg_node, 0);
+		of_node_put(scfg_node);
 		if (scfg_base) {
 			sdhciovselcr = SDHCIOVSELCR_TGLEN |
 				       SDHCIOVSELCR_VSELVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-omap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-omap.c
@@ -62,6 +62,8 @@
 #define SDHCI_OMAP_IE		0x234
 #define INT_CC_EN		BIT(0)
 
+#define SDHCI_OMAP_ISE		0x238
+
 #define SDHCI_OMAP_AC12		0x23c
 #define AC12_V1V8_SIGEN		BIT(19)
 #define AC12_SCLK_SEL		BIT(23)
@@ -113,6 +115,8 @@
 	u32			hctl;
 	u32			sysctl;
 	u32			capa;
+	u32			ie;
+	u32			ise;
 };
 
 static void sdhci_omap_start_clock(struct sdhci_omap_host *omap_host);
@@ -682,7 +686,8 @@
 {
 	struct mmc_host *mmc = host->mmc;
 
-	mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
+	if (!IS_ERR(mmc->supply.vmmc))
+		mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
 }
 
 static int sdhci_omap_enable_dma(struct sdhci_host *host)
@@ -1244,14 +1249,23 @@
 {
 	omap_host->con = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
 	omap_host->hctl = sdhci_omap_readl(omap_host, SDHCI_OMAP_HCTL);
+	omap_host->sysctl = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCTL);
 	omap_host->capa = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
+	omap_host->ie = sdhci_omap_readl(omap_host, SDHCI_OMAP_IE);
+	omap_host->ise = sdhci_omap_readl(omap_host, SDHCI_OMAP_ISE);
 }
 
+/* Order matters here, HCTL must be restored in two phases */
 static void sdhci_omap_context_restore(struct sdhci_omap_host *omap_host)
 {
-	sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, omap_host->con);
 	sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, omap_host->hctl);
 	sdhci_omap_writel(omap_host, SDHCI_OMAP_CAPA, omap_host->capa);
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, omap_host->hctl);
+
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCTL, omap_host->sysctl);
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, omap_host->con);
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_IE, omap_host->ie);
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_ISE, omap_host->ise);
 }
 
 static int __maybe_unused sdhci_omap_suspend(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-pci-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-pci-core.c
@@ -23,6 +23,7 @@
 #include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/pm_runtime.h>
 #include <linux/pm_qos.h>
 #include <linux/debugfs.h>
@@ -978,6 +979,12 @@
 		dmi_match(DMI_SYS_VENDOR, "IRBIS"));
 }
 
+static bool jsl_broken_hs400es(struct sdhci_pci_slot *slot)
+{
+	return slot->chip->pdev->device == PCI_DEVICE_ID_INTEL_JSL_EMMC &&
+			dmi_match(DMI_BIOS_VENDOR, "ASUSTeK COMPUTER INC.");
+}
+
 static int glk_emmc_probe_slot(struct sdhci_pci_slot *slot)
 {
 	int ret = byt_emmc_probe_slot(slot);
@@ -986,9 +993,11 @@
 		slot->host->mmc->caps2 |= MMC_CAP2_CQE;
 
 	if (slot->chip->pdev->device != PCI_DEVICE_ID_INTEL_GLK_EMMC) {
-		slot->host->mmc->caps2 |= MMC_CAP2_HS400_ES;
-		slot->host->mmc_host_ops.hs400_enhanced_strobe =
-						intel_hs400_enhanced_strobe;
+		if (!jsl_broken_hs400es(slot)) {
+			slot->host->mmc->caps2 |= MMC_CAP2_HS400_ES;
+			slot->host->mmc_host_ops.hs400_enhanced_strobe =
+							intel_hs400_enhanced_strobe;
+		}
 		slot->host->mmc->caps2 |= MMC_CAP2_CQE_DCMD;
 	}
 
@@ -1295,6 +1304,29 @@
 	.priv_size	= sizeof(struct intel_host),
 };
 
+/* DMI quirks for devices with missing or broken CD GPIO info */
+static const struct gpiod_lookup_table vexia_edu_atla10_cd_gpios = {
+	.dev_id = "0000:00:12.0",
+	.table = {
+		GPIO_LOOKUP("INT33FC:00", 38, "cd", GPIO_ACTIVE_HIGH),
+		{ }
+	},
+};
+
+static const struct dmi_system_id sdhci_intel_byt_cd_gpio_override[] = {
+	{
+		/* Vexia Edu Atla 10 tablet 9V version */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "Aptio CRB"),
+			/* Above strings are too generic, also match on BIOS date */
+			DMI_MATCH(DMI_BIOS_DATE, "08/25/2014"),
+		},
+		.driver_data = (void *)&vexia_edu_atla10_cd_gpios,
+	},
+	{ }
+};
+
 static const struct sdhci_pci_fixes sdhci_intel_byt_sd = {
 #ifdef CONFIG_PM_SLEEP
 	.resume		= byt_resume,
@@ -1313,6 +1345,7 @@
 	.add_host	= byt_add_host,
 	.remove_slot	= byt_remove_slot,
 	.ops		= &sdhci_intel_byt_ops,
+	.cd_gpio_override = sdhci_intel_byt_cd_gpio_override,
 	.priv_size	= sizeof(struct intel_host),
 };
 
@@ -1391,7 +1424,7 @@
 
 	ret = pci_read_config_byte(chip->pdev, 0xAE, &scratch);
 	if (ret)
-		return ret;
+		goto fail;
 
 	/*
 	 * Turn PMOS on [bit 0], set over current detection to 2.4 V
@@ -1402,7 +1435,10 @@
 	else
 		scratch &= ~0x47;
 
-	return pci_write_config_byte(chip->pdev, 0xAE, scratch);
+	ret = pci_write_config_byte(chip->pdev, 0xAE, scratch);
+
+fail:
+	return pcibios_err_to_errno(ret);
 }
 
 static int jmicron_probe(struct sdhci_pci_chip *chip)
@@ -1810,6 +1846,8 @@
 		}
 	}
 
+	pci_dev_put(smbus_dev);
+
 	if (gen == AMD_CHIPSET_BEFORE_ML || gen == AMD_CHIPSET_CZ)
 		chip->quirks2 |= SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD;
 
@@ -1951,6 +1989,7 @@
 	SDHCI_PCI_DEVICE(INTEL, JSL_SD,    intel_byt_sd),
 	SDHCI_PCI_DEVICE(INTEL, LKF_EMMC,  intel_glk_emmc),
 	SDHCI_PCI_DEVICE(INTEL, LKF_SD,    intel_byt_sd),
+	SDHCI_PCI_DEVICE(INTEL, ADL_EMMC,  intel_glk_emmc),
 	SDHCI_PCI_DEVICE(O2, 8120,     o2),
 	SDHCI_PCI_DEVICE(O2, 8220,     o2),
 	SDHCI_PCI_DEVICE(O2, 8221,     o2),
@@ -2106,6 +2145,42 @@
  *                                                                           *
 \*****************************************************************************/
 
+static struct gpiod_lookup_table *sdhci_pci_add_gpio_lookup_table(
+	struct sdhci_pci_chip *chip)
+{
+	struct gpiod_lookup_table *cd_gpio_lookup_table;
+	const struct dmi_system_id *dmi_id = NULL;
+	size_t count;
+
+	if (chip->fixes && chip->fixes->cd_gpio_override)
+		dmi_id = dmi_first_match(chip->fixes->cd_gpio_override);
+
+	if (!dmi_id)
+		return NULL;
+
+	cd_gpio_lookup_table = dmi_id->driver_data;
+	for (count = 0; cd_gpio_lookup_table->table[count].key; count++)
+		;
+
+	cd_gpio_lookup_table = kmemdup(dmi_id->driver_data,
+				       /* count + 1 terminating entry */
+				       struct_size(cd_gpio_lookup_table, table, count + 1),
+				       GFP_KERNEL);
+	if (!cd_gpio_lookup_table)
+		return ERR_PTR(-ENOMEM);
+
+	gpiod_add_lookup_table(cd_gpio_lookup_table);
+	return cd_gpio_lookup_table;
+}
+
+static void sdhci_pci_remove_gpio_lookup_table(struct gpiod_lookup_table *lookup_table)
+{
+	if (lookup_table) {
+		gpiod_remove_lookup_table(lookup_table);
+		kfree(lookup_table);
+	}
+}
+
 static struct sdhci_pci_slot *sdhci_pci_probe_slot(
 	struct pci_dev *pdev, struct sdhci_pci_chip *chip, int first_bar,
 	int slotno)
@@ -2210,8 +2285,19 @@
 		device_init_wakeup(&pdev->dev, true);
 
 	if (slot->cd_idx >= 0) {
+		struct gpiod_lookup_table *cd_gpio_lookup_table;
+
+		cd_gpio_lookup_table = sdhci_pci_add_gpio_lookup_table(chip);
+		if (IS_ERR(cd_gpio_lookup_table)) {
+			ret = PTR_ERR(cd_gpio_lookup_table);
+			goto remove;
+		}
+
 		ret = mmc_gpiod_request_cd(host->mmc, "cd", slot->cd_idx,
 					   slot->cd_override_level, 0);
+
+		sdhci_pci_remove_gpio_lookup_table(cd_gpio_lookup_table);
+
 		if (ret && ret != -EPROBE_DEFER)
 			ret = mmc_gpiod_request_cd(host->mmc, NULL,
 						   slot->cd_idx,
@@ -2316,7 +2402,7 @@
 
 	ret = pci_read_config_byte(pdev, PCI_SLOT_INFO, &slots);
 	if (ret)
-		return ret;
+		return pcibios_err_to_errno(ret);
 
 	slots = PCI_SLOT_INFO_SLOTS(slots) + 1;
 	dev_dbg(&pdev->dev, "found %d slot(s)\n", slots);
@@ -2325,7 +2411,7 @@
 
 	ret = pci_read_config_byte(pdev, PCI_SLOT_INFO, &first_bar);
 	if (ret)
-		return ret;
+		return pcibios_err_to_errno(ret);
 
 	first_bar &= PCI_SLOT_INFO_FIRST_BAR_MASK;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-pci-gli.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-pci-gli.c
@@ -12,6 +12,7 @@
 #include <linux/pci.h>
 #include <linux/mmc/mmc.h>
 #include <linux/delay.h>
+#include <linux/of.h>
 #include "sdhci.h"
 #include "sdhci-pci.h"
 #include "cqhci.h"
@@ -22,6 +23,12 @@
 #define   GLI_9750_WT_EN_ON	    0x1
 #define   GLI_9750_WT_EN_OFF	    0x0
 
+#define PCI_GLI_9750_PM_CTRL	0xFC
+#define   PCI_GLI_9750_PM_STATE	  GENMASK(1, 0)
+
+#define PCI_GLI_9750_CORRERR_MASK				0x214
+#define   PCI_GLI_9750_CORRERR_MASK_REPLAY_TIMER_TIMEOUT	  BIT(12)
+
 #define SDHCI_GLI_9750_CFG2          0x848
 #define   SDHCI_GLI_9750_CFG2_L1DLY    GENMASK(28, 24)
 #define   GLI_9750_CFG2_L1DLY_VALUE    0x1F
@@ -116,6 +123,8 @@
 #define PCI_GLI_9755_PECONF   0x44
 #define   PCI_GLI_9755_LFCLK    GENMASK(14, 12)
 #define   PCI_GLI_9755_DMACLK   BIT(29)
+#define   PCI_GLI_9755_INVERT_CD  BIT(30)
+#define   PCI_GLI_9755_INVERT_WP  BIT(31)
 
 #define PCI_GLI_9755_CFG2          0x48
 #define   PCI_GLI_9755_CFG2_L1DLY    GENMASK(28, 24)
@@ -418,8 +427,12 @@
 
 static void gl9750_hw_setting(struct sdhci_host *host)
 {
+	struct sdhci_pci_slot *slot = sdhci_priv(host);
+	struct pci_dev *pdev;
 	u32 value;
 
+	pdev = slot->chip->pdev;
+
 	gl9750_wt_on(host);
 
 	value = sdhci_readl(host, SDHCI_GLI_9750_CFG2);
@@ -429,6 +442,18 @@
 			    GLI_9750_CFG2_L1DLY_VALUE);
 	sdhci_writel(host, value, SDHCI_GLI_9750_CFG2);
 
+	/* toggle PM state to allow GL9750 to enter ASPM L1.2 */
+	pci_read_config_dword(pdev, PCI_GLI_9750_PM_CTRL, &value);
+	value |= PCI_GLI_9750_PM_STATE;
+	pci_write_config_dword(pdev, PCI_GLI_9750_PM_CTRL, value);
+	value &= ~PCI_GLI_9750_PM_STATE;
+	pci_write_config_dword(pdev, PCI_GLI_9750_PM_CTRL, value);
+
+	/* mask the replay timer timeout of AER */
+	pci_read_config_dword(pdev, PCI_GLI_9750_CORRERR_MASK, &value);
+	value |= PCI_GLI_9750_CORRERR_MASK_REPLAY_TIMER_TIMEOUT;
+	pci_write_config_dword(pdev, PCI_GLI_9750_CORRERR_MASK, value);
+
 	gl9750_wt_off(host);
 }
 
@@ -570,6 +595,14 @@
 	gl9755_wt_on(pdev);
 
 	pci_read_config_dword(pdev, PCI_GLI_9755_PECONF, &value);
+	/*
+	 * Apple ARM64 platforms using these chips may have
+	 * inverted CD/WP detection.
+	 */
+	if (of_property_read_bool(pdev->dev.of_node, "cd-inverted"))
+		value |= PCI_GLI_9755_INVERT_CD;
+	if (of_property_read_bool(pdev->dev.of_node, "wp-inverted"))
+		value |= PCI_GLI_9755_INVERT_WP;
 	value &= ~PCI_GLI_9755_LFCLK;
 	value &= ~PCI_GLI_9755_DMACLK;
 	pci_write_config_dword(pdev, PCI_GLI_9755_PECONF, value);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-pci-o2micro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -31,6 +31,7 @@
 #define O2_SD_CAPS		0xE0
 #define O2_SD_ADMA1		0xE2
 #define O2_SD_ADMA2		0xE7
+#define O2_SD_MISC_CTRL2	0xF0
 #define O2_SD_INF_MOD		0xF1
 #define O2_SD_MISC_CTRL4	0xFC
 #define O2_SD_MISC_CTRL		0x1C0
@@ -147,6 +148,8 @@
 
 	if (!(sdhci_readw(host, O2_PLL_DLL_WDT_CONTROL1) & O2_PLL_LOCK_STATUS))
 		sdhci_o2_enable_internal_clock(host);
+	else
+		sdhci_o2_wait_card_detect_stable(host);
 
 	return !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
 }
@@ -828,6 +831,12 @@
 		/* Set Tuning Windows to 5 */
 		pci_write_config_byte(chip->pdev,
 				O2_SD_TUNING_CTRL, 0x55);
+		//Adjust 1st and 2nd CD debounce time
+		pci_read_config_dword(chip->pdev, O2_SD_MISC_CTRL2, &scratch_32);
+		scratch_32 &= 0xFFE7FFFF;
+		scratch_32 |= 0x00180000;
+		pci_write_config_dword(chip->pdev, O2_SD_MISC_CTRL2, scratch_32);
+		pci_write_config_dword(chip->pdev, O2_SD_DETECT_SETTING, 1);
 		/* Lock WP */
 		ret = pci_read_config_byte(chip->pdev,
 					   O2_SD_LOCK_WP, &scratch);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-pci.h
@@ -59,6 +59,7 @@
 #define PCI_DEVICE_ID_INTEL_JSL_SD	0x4df8
 #define PCI_DEVICE_ID_INTEL_LKF_EMMC	0x98c4
 #define PCI_DEVICE_ID_INTEL_LKF_SD	0x98f8
+#define PCI_DEVICE_ID_INTEL_ADL_EMMC	0x54c4
 
 #define PCI_DEVICE_ID_SYSKONNECT_8000	0x8000
 #define PCI_DEVICE_ID_VIA_95D0		0x95d0
@@ -150,6 +151,7 @@
 #endif
 
 	const struct sdhci_ops	*ops;
+	const struct dmi_system_id *cd_gpio_override;
 	size_t			priv_size;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-pxav3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-pxav3.c
@@ -401,6 +401,7 @@
 	if (!IS_ERR(pxa->clk_core))
 		clk_prepare_enable(pxa->clk_core);
 
+	host->mmc->caps |= MMC_CAP_NEED_RSP_BUSY;
 	/* enable 1/8V DDR capable */
 	host->mmc->caps |= MMC_CAP_1_8V_DDR;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-sprd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-sprd.c
@@ -224,13 +224,19 @@
 	div = ((div & 0x300) >> 2) | ((div & 0xFF) << 8);
 	sdhci_enable_clk(host, div);
 
-	/* enable auto gate sdhc_enable_auto_gate */
 	val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI);
-	mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN |
-	       SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN;
-	if (mask != (val & mask)) {
-		val |= mask;
-		sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI);
+	mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN | SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN;
+	/* Enable CLK_AUTO when the clock is greater than 400K. */
+	if (clk > 400000) {
+		if (mask != (val & mask)) {
+			val |= mask;
+			sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI);
+		}
+	} else {
+		if (val & mask) {
+			val &= ~mask;
+			sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI);
+		}
 	}
 }
 
@@ -296,7 +302,7 @@
 
 static unsigned int sdhci_sprd_get_min_clock(struct sdhci_host *host)
 {
-	return 400000;
+	return 100000;
 }
 
 static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host,
@@ -390,12 +396,33 @@
 	mmc_request_done(host->mmc, mrq);
 }
 
+static void sdhci_sprd_set_power(struct sdhci_host *host, unsigned char mode,
+				 unsigned short vdd)
+{
+	struct mmc_host *mmc = host->mmc;
+
+	switch (mode) {
+	case MMC_POWER_OFF:
+		mmc_regulator_set_ocr(host->mmc, mmc->supply.vmmc, 0);
+
+		mmc_regulator_disable_vqmmc(mmc);
+		break;
+	case MMC_POWER_ON:
+		mmc_regulator_enable_vqmmc(mmc);
+		break;
+	case MMC_POWER_UP:
+		mmc_regulator_set_ocr(host->mmc, mmc->supply.vmmc, vdd);
+		break;
+	}
+}
+
 static struct sdhci_ops sdhci_sprd_ops = {
 	.read_l = sdhci_sprd_readl,
 	.write_l = sdhci_sprd_writel,
 	.write_w = sdhci_sprd_writew,
 	.write_b = sdhci_sprd_writeb,
 	.set_clock = sdhci_sprd_set_clock,
+	.set_power = sdhci_sprd_set_power,
 	.get_max_clock = sdhci_sprd_get_max_clock,
 	.get_min_clock = sdhci_sprd_get_min_clock,
 	.set_bus_width = sdhci_set_bus_width,
@@ -457,7 +484,7 @@
 	}
 
 	if (IS_ERR(sprd_host->pinctrl))
-		return 0;
+		goto reset;
 
 	switch (ios->signal_voltage) {
 	case MMC_SIGNAL_VOLTAGE_180:
@@ -485,6 +512,8 @@
 
 	/* Wait for 300 ~ 500 us for pin state stable */
 	usleep_range(300, 500);
+
+reset:
 	sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 
 	return 0;
@@ -659,6 +688,10 @@
 	host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 |
 			 SDHCI_SUPPORT_DDR50);
 
+	ret = mmc_regulator_get_supply(host->mmc);
+	if (ret)
+		goto pm_runtime_disable;
+
 	ret = sdhci_setup_host(host);
 	if (ret)
 		goto pm_runtime_disable;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-tegra.c
@@ -24,6 +24,7 @@
 #include <linux/gpio/consumer.h>
 #include <linux/ktime.h>
 
+#include "sdhci-cqhci.h"
 #include "sdhci-pltfm.h"
 #include "cqhci.h"
 
@@ -356,23 +357,6 @@
 	}
 }
 
-static void tegra_sdhci_hs400_enhanced_strobe(struct mmc_host *mmc,
-					      struct mmc_ios *ios)
-{
-	struct sdhci_host *host = mmc_priv(mmc);
-	u32 val;
-
-	val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
-
-	if (ios->enhanced_strobe)
-		val |= SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
-	else
-		val &= ~SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
-
-	sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
-
-}
-
 static void tegra_sdhci_reset(struct sdhci_host *host, u8 mask)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
@@ -380,7 +364,7 @@
 	const struct sdhci_tegra_soc_data *soc_data = tegra_host->soc_data;
 	u32 misc_ctrl, clk_ctrl, pad_ctrl;
 
-	sdhci_reset(host, mask);
+	sdhci_and_cqhci_reset(host, mask);
 
 	if (!(mask & SDHCI_RESET_ALL))
 		return;
@@ -779,7 +763,7 @@
 	 */
 	host_clk = tegra_host->ddr_signaling ? clock * 2 : clock;
 	clk_set_rate(pltfm_host->clk, host_clk);
-	tegra_host->curr_clk_rate = host_clk;
+	tegra_host->curr_clk_rate = clk_get_rate(pltfm_host->clk);
 	if (tegra_host->ddr_signaling)
 		host->max_clk = host_clk;
 	else
@@ -793,6 +777,32 @@
 	}
 }
 
+static void tegra_sdhci_hs400_enhanced_strobe(struct mmc_host *mmc,
+					      struct mmc_ios *ios)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	u32 val;
+
+	val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
+
+	if (ios->enhanced_strobe) {
+		val |= SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
+		/*
+		 * When CMD13 is sent from mmc_select_hs400es() after
+		 * switching to HS400ES mode, the bus is operating at
+		 * either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR.
+		 * To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI
+		 * interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host
+		 * controller CAR clock and the interface clock are rate matched.
+		 */
+		tegra_sdhci_set_clock(host, MMC_HS200_MAX_DTR);
+	} else {
+		val &= ~SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
+	}
+
+	sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
+}
+
 static unsigned int tegra_sdhci_get_max_clock(struct sdhci_host *host)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
@@ -1372,7 +1382,6 @@
 		  SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
 		  SDHCI_QUIRK_SINGLE_POWER_WRITE |
 		  SDHCI_QUIRK_NO_HISPD_BIT |
-		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC |
 		  SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
 	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
 		   SDHCI_QUIRK2_BROKEN_HS200 |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-xenon-phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-xenon-phy.c
@@ -11,6 +11,7 @@
 #include <linux/slab.h>
 #include <linux/delay.h>
 #include <linux/ktime.h>
+#include <linux/iopoll.h>
 #include <linux/of_address.h>
 
 #include "sdhci-pltfm.h"
@@ -109,6 +110,8 @@
 #define XENON_EMMC_PHY_LOGIC_TIMING_ADJUST	(XENON_EMMC_PHY_REG_BASE + 0x18)
 #define XENON_LOGIC_TIMING_VALUE		0x00AA8977
 
+#define XENON_MAX_PHY_TIMEOUT_LOOPS		100
+
 /*
  * List offset of PHY registers and some special register values
  * in eMMC PHY 5.0 or eMMC PHY 5.1
@@ -216,6 +219,19 @@
 	return 0;
 }
 
+static int xenon_check_stability_internal_clk(struct sdhci_host *host)
+{
+	u32 reg;
+	int err;
+
+	err = read_poll_timeout(sdhci_readw, reg, reg & SDHCI_CLOCK_INT_STABLE,
+				1100, 20000, false, host, SDHCI_CLOCK_CONTROL);
+	if (err)
+		dev_err(mmc_dev(host->mmc), "phy_init: Internal clock never stabilized.\n");
+
+	return err;
+}
+
 /*
  * eMMC 5.0/5.1 PHY init/re-init.
  * eMMC PHY init should be executed after:
@@ -232,6 +248,11 @@
 	struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
 	struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
 
+	int ret = xenon_check_stability_internal_clk(host);
+
+	if (ret)
+		return ret;
+
 	reg = sdhci_readl(host, phy_regs->timing_adj);
 	reg |= XENON_PHY_INITIALIZAION;
 	sdhci_writel(host, reg, phy_regs->timing_adj);
@@ -259,18 +280,27 @@
 	/* get the wait time */
 	wait /= clock;
 	wait++;
-	/* wait for host eMMC PHY init completes */
-	udelay(wait);
 
-	reg = sdhci_readl(host, phy_regs->timing_adj);
-	reg &= XENON_PHY_INITIALIZAION;
-	if (reg) {
+	/*
+	 * AC5X spec says bit must be polled until zero.
+	 * We see cases in which timeout can take longer
+	 * than the standard calculation on AC5X, which is
+	 * expected following the spec comment above.
+	 * According to the spec, we must wait as long as
+	 * it takes for that bit to toggle on AC5X.
+	 * Cap that with 100 delay loops so we won't get
+	 * stuck here forever:
+	 */
+
+	ret = read_poll_timeout(sdhci_readl, reg,
+				!(reg & XENON_PHY_INITIALIZAION),
+				wait, XENON_MAX_PHY_TIMEOUT_LOOPS * wait,
+				false, host, phy_regs->timing_adj);
+	if (ret)
 		dev_err(mmc_dev(host->mmc), "eMMC PHY init cannot complete after %d us\n",
-			wait);
-		return -ETIMEDOUT;
-	}
+			wait * XENON_MAX_PHY_TIMEOUT_LOOPS);
 
-	return 0;
+	return ret;
 }
 
 #define ARMADA_3700_SOC_PAD_1_8V	0x1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci-xenon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci-xenon.c
@@ -241,16 +241,6 @@
 {
 	/* Wait for 5ms after set 1.8V signal enable bit */
 	usleep_range(5000, 5500);
-
-	/*
-	 * For some reason the controller's Host Control2 register reports
-	 * the bit representing 1.8V signaling as 0 when read after it was
-	 * written as 1. Subsequent read reports 1.
-	 *
-	 * Since this may cause some issues, do an empty read of the Host
-	 * Control2 register here to circumvent this.
-	 */
-	sdhci_readw(host, SDHCI_HOST_CONTROL2);
 }
 
 static unsigned int xenon_get_max_clock(struct sdhci_host *host)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci.c
@@ -338,6 +338,7 @@
 	if (soft) {
 		/* force clock reconfiguration */
 		host->clock = 0;
+		host->reinit_uhs = true;
 		mmc->ops->set_ios(mmc, &mmc->ios);
 	}
 }
@@ -771,7 +772,19 @@
 			len -= offset;
 		}
 
-		BUG_ON(len > 65536);
+		/*
+		 * The block layer forces a minimum segment size of PAGE_SIZE,
+		 * so 'len' can be too big here if PAGE_SIZE >= 64KiB. Write
+		 * multiple descriptors, noting that the ADMA table is sized
+		 * for 4KiB chunks anyway, so it will be big enough.
+		 */
+		while (len > host->max_adma) {
+			int n = 32 * 1024; /* 32KiB*/
+
+			__sdhci_adma_write_desc(host, &desc, addr, n, ADMA2_TRAN_VALID);
+			addr += n;
+			len -= n;
+		}
 
 		/* tran, valid */
 		if (len)
@@ -1131,6 +1144,8 @@
 		}
 	}
 
+	sdhci_config_dma(host);
+
 	if (host->flags & SDHCI_REQ_USE_DMA) {
 		int sg_cnt = sdhci_pre_dma_transfer(host, data, COOKIE_MAPPED);
 
@@ -1150,8 +1165,6 @@
 		}
 	}
 
-	sdhci_config_dma(host);
-
 	if (!(host->flags & SDHCI_REQ_USE_DMA)) {
 		int flags;
 
@@ -2245,11 +2258,46 @@
 }
 EXPORT_SYMBOL_GPL(sdhci_set_uhs_signaling);
 
+static bool sdhci_timing_has_preset(unsigned char timing)
+{
+	switch (timing) {
+	case MMC_TIMING_UHS_SDR12:
+	case MMC_TIMING_UHS_SDR25:
+	case MMC_TIMING_UHS_SDR50:
+	case MMC_TIMING_UHS_SDR104:
+	case MMC_TIMING_UHS_DDR50:
+	case MMC_TIMING_MMC_DDR52:
+		return true;
+	};
+	return false;
+}
+
+static bool sdhci_preset_needed(struct sdhci_host *host, unsigned char timing)
+{
+	return !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
+	       sdhci_timing_has_preset(timing);
+}
+
+static bool sdhci_presetable_values_change(struct sdhci_host *host, struct mmc_ios *ios)
+{
+	/*
+	 * Preset Values are: Driver Strength, Clock Generator and SDCLK/RCLK
+	 * Frequency. Check if preset values need to be enabled, or the Driver
+	 * Strength needs updating. Note, clock changes are handled separately.
+	 */
+	return !host->preset_enabled &&
+	       (sdhci_preset_needed(host, ios->timing) || host->drv_type != ios->drv_type);
+}
+
 void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct sdhci_host *host = mmc_priv(mmc);
+	bool reinit_uhs = host->reinit_uhs;
+	bool turning_on_clk = false;
 	u8 ctrl;
 
+	host->reinit_uhs = false;
+
 	if (ios->power_mode == MMC_POWER_UNDEFINED)
 		return;
 
@@ -2275,6 +2323,8 @@
 		sdhci_enable_preset_value(host, false);
 
 	if (!ios->clock || ios->clock != host->clock) {
+		turning_on_clk = ios->clock && !host->clock;
+
 		host->ops->set_clock(host, ios->clock);
 		host->clock = ios->clock;
 
@@ -2301,6 +2351,17 @@
 
 	host->ops->set_bus_width(host, ios->bus_width);
 
+	/*
+	 * Special case to avoid multiple clock changes during voltage
+	 * switching.
+	 */
+	if (!reinit_uhs &&
+	    turning_on_clk &&
+	    host->timing == ios->timing &&
+	    host->version >= SDHCI_SPEC_300 &&
+	    !sdhci_presetable_values_change(host, ios))
+		return;
+
 	ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 
 	if (!(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT)) {
@@ -2344,6 +2405,7 @@
 			}
 
 			sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+			host->drv_type = ios->drv_type;
 		} else {
 			/*
 			 * According to SDHC Spec v3.00, if the Preset Value
@@ -2371,19 +2433,14 @@
 		host->ops->set_uhs_signaling(host, ios->timing);
 		host->timing = ios->timing;
 
-		if (!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
-				((ios->timing == MMC_TIMING_UHS_SDR12) ||
-				 (ios->timing == MMC_TIMING_UHS_SDR25) ||
-				 (ios->timing == MMC_TIMING_UHS_SDR50) ||
-				 (ios->timing == MMC_TIMING_UHS_SDR104) ||
-				 (ios->timing == MMC_TIMING_UHS_DDR50) ||
-				 (ios->timing == MMC_TIMING_MMC_DDR52))) {
+		if (sdhci_preset_needed(host, ios->timing)) {
 			u16 preset;
 
 			sdhci_enable_preset_value(host, true);
 			preset = sdhci_get_preset_value(host);
 			ios->drv_type = FIELD_GET(SDHCI_PRESET_DRV_MASK,
 						  preset);
+			host->drv_type = ios->drv_type;
 		}
 
 		/* Re-enable SD Clock */
@@ -2430,26 +2487,29 @@
 
 static int sdhci_check_ro(struct sdhci_host *host)
 {
-	unsigned long flags;
+	bool allow_invert = false;
 	int is_readonly;
 
-	spin_lock_irqsave(&host->lock, flags);
-
-	if (host->flags & SDHCI_DEVICE_DEAD)
+	if (host->flags & SDHCI_DEVICE_DEAD) {
 		is_readonly = 0;
-	else if (host->ops->get_ro)
+	} else if (host->ops->get_ro) {
 		is_readonly = host->ops->get_ro(host);
-	else if (mmc_can_gpio_ro(host->mmc))
+	} else if (mmc_can_gpio_ro(host->mmc)) {
 		is_readonly = mmc_gpio_get_ro(host->mmc);
-	else
+		/* Do not invert twice */
+		allow_invert = !(host->mmc->caps2 & MMC_CAP2_RO_ACTIVE_HIGH);
+	} else {
 		is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
 				& SDHCI_WRITE_PROTECT);
+		allow_invert = true;
+	}
 
-	spin_unlock_irqrestore(&host->lock, flags);
+	if (is_readonly >= 0 &&
+	    allow_invert &&
+	    (host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT))
+		is_readonly = !is_readonly;
 
-	/* This quirk needs to be replaced by a callback-function later */
-	return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
-		!is_readonly : is_readonly;
+	return is_readonly;
 }
 
 #define SAMPLE_COUNT	5
@@ -3699,6 +3759,7 @@
 		sdhci_init(host, 0);
 		host->pwr = 0;
 		host->clock = 0;
+		host->reinit_uhs = true;
 		mmc->ops->set_ios(mmc, &mmc->ios);
 	} else {
 		sdhci_init(host, (mmc->pm_flags & MMC_PM_KEEP_POWER));
@@ -3761,6 +3822,7 @@
 		/* Force clock and power re-program */
 		host->pwr = 0;
 		host->clock = 0;
+		host->reinit_uhs = true;
 		mmc->ops->start_signal_voltage_switch(mmc, &mmc->ios);
 		mmc->ops->set_ios(mmc, &mmc->ios);
 
@@ -3952,6 +4014,7 @@
 	 * descriptor for each segment, plus 1 for a nop end descriptor.
 	 */
 	host->adma_table_cnt = SDHCI_MAX_SEGS * 2 + 1;
+	host->max_adma = 65536;
 
 	host->max_timeout_count = 0xE;
 
@@ -4617,10 +4680,12 @@
 	 * be larger than 64 KiB though.
 	 */
 	if (host->flags & SDHCI_USE_ADMA) {
-		if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC)
+		if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC) {
+			host->max_adma = 65532; /* 32-bit alignment */
 			mmc->max_seg_size = 65535;
-		else
+		} else {
 			mmc->max_seg_size = 65536;
+		}
 	} else {
 		mmc->max_seg_size = mmc->max_req_size;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci.h
@@ -340,7 +340,8 @@
 
 /*
  * Maximum segments assuming a 512KiB maximum requisition size and a minimum
- * 4KiB page size.
+ * 4KiB page size. Note this also allows enough for multiple descriptors in
+ * case of PAGE_SIZE >= 64KiB.
  */
 #define SDHCI_MAX_SEGS		128
 
@@ -522,6 +523,8 @@
 
 	unsigned int clock;	/* Current clock (MHz) */
 	u8 pwr;			/* Current voltage */
+	u8 drv_type;		/* Current UHS-I driver type */
+	bool reinit_uhs;	/* Force UHS-related re-initialization */
 
 	bool runtime_suspended;	/* Host is runtime suspended */
 	bool bus_on;		/* Bus power prevents runtime suspend */
@@ -543,6 +546,7 @@
 	unsigned int blocks;	/* remaining PIO blocks */
 
 	int sg_count;		/* Mapped sg entries */
+	int max_adma;		/* Max. length in ADMA descriptor */
 
 	void *adma_table;	/* ADMA descriptor table */
 	void *align_buffer;	/* Bounce buffer */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci_am654.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci_am654.c
@@ -15,6 +15,7 @@
 #include <linux/sys_soc.h>
 
 #include "cqhci.h"
+#include "sdhci-cqhci.h"
 #include "sdhci-pltfm.h"
 
 /* CTL_CFG Registers */
@@ -139,14 +140,24 @@
 
 struct sdhci_am654_data {
 	struct regmap *base;
-	bool legacy_otapdly;
 	int otap_del_sel[ARRAY_SIZE(td)];
 	int itap_del_sel[ARRAY_SIZE(td)];
+	u32 itap_del_ena[ARRAY_SIZE(td)];
 	int clkbuf_sel;
 	int trm_icp;
 	int drv_strength;
 	int strb_sel;
 	u32 flags;
+	u32 quirks;
+	bool dll_enable;
+
+#define SDHCI_AM654_QUIRK_FORCE_CDTEST BIT(0)
+};
+
+struct window {
+	u8 start;
+	u8 end;
+	u8 length;
 };
 
 struct sdhci_am654_driver_data {
@@ -228,11 +239,13 @@
 }
 
 static void sdhci_am654_write_itapdly(struct sdhci_am654_data *sdhci_am654,
-				      u32 itapdly)
+				      u32 itapdly, u32 enable)
 {
 	/* Set ITAPCHGWIN before writing to ITAPDLY */
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPCHGWIN_MASK,
 			   1 << ITAPCHGWIN_SHIFT);
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPDLYENA_MASK,
+			   enable << ITAPDLYENA_SHIFT);
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPDLYSEL_MASK,
 			   itapdly << ITAPDLYSEL_SHIFT);
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPCHGWIN_MASK, 0);
@@ -249,8 +262,8 @@
 	mask = SELDLYTXCLK_MASK | SELDLYRXCLK_MASK;
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL5, mask, val);
 
-	sdhci_am654_write_itapdly(sdhci_am654,
-				  sdhci_am654->itap_del_sel[timing]);
+	sdhci_am654_write_itapdly(sdhci_am654, sdhci_am654->itap_del_sel[timing],
+				  sdhci_am654->itap_del_ena[timing]);
 }
 
 static void sdhci_am654_set_clock(struct sdhci_host *host, unsigned int clock)
@@ -259,7 +272,6 @@
 	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
 	unsigned char timing = host->mmc->ios.timing;
 	u32 otap_del_sel;
-	u32 otap_del_ena;
 	u32 mask, val;
 
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL1, ENDLL_MASK, 0);
@@ -267,15 +279,10 @@
 	sdhci_set_clock(host, clock);
 
 	/* Setup DLL Output TAP delay */
-	if (sdhci_am654->legacy_otapdly)
-		otap_del_sel = sdhci_am654->otap_del_sel[0];
-	else
-		otap_del_sel = sdhci_am654->otap_del_sel[timing];
-
-	otap_del_ena = (timing > MMC_TIMING_UHS_SDR25) ? 1 : 0;
+	otap_del_sel = sdhci_am654->otap_del_sel[timing];
 
 	mask = OTAPDLYENA_MASK | OTAPDLYSEL_MASK;
-	val = (otap_del_ena << OTAPDLYENA_SHIFT) |
+	val = (0x1 << OTAPDLYENA_SHIFT) |
 	      (otap_del_sel << OTAPDLYSEL_SHIFT);
 
 	/* Write to STRBSEL for HS400 speed mode */
@@ -290,10 +297,21 @@
 
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, mask, val);
 
-	if (timing > MMC_TIMING_UHS_SDR25 && clock >= CLOCK_TOO_SLOW_HZ)
+	if (timing > MMC_TIMING_UHS_SDR25 && clock >= CLOCK_TOO_SLOW_HZ) {
 		sdhci_am654_setup_dll(host, clock);
-	else
+		sdhci_am654->dll_enable = true;
+
+		if (timing == MMC_TIMING_MMC_HS400) {
+			sdhci_am654->itap_del_ena[timing] = 0x1;
+			sdhci_am654->itap_del_sel[timing] = sdhci_am654->itap_del_sel[timing - 1];
+		}
+
+		sdhci_am654_write_itapdly(sdhci_am654, sdhci_am654->itap_del_sel[timing],
+					  sdhci_am654->itap_del_ena[timing]);
+	} else {
 		sdhci_am654_setup_delay_chain(sdhci_am654, timing);
+		sdhci_am654->dll_enable = false;
+	}
 
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL5, CLKBUFSEL_MASK,
 			   sdhci_am654->clkbuf_sel);
@@ -306,19 +324,29 @@
 	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
 	unsigned char timing = host->mmc->ios.timing;
 	u32 otap_del_sel;
+	u32 itap_del_ena;
+	u32 itap_del_sel;
 	u32 mask, val;
 
 	/* Setup DLL Output TAP delay */
-	if (sdhci_am654->legacy_otapdly)
-		otap_del_sel = sdhci_am654->otap_del_sel[0];
-	else
-		otap_del_sel = sdhci_am654->otap_del_sel[timing];
+	otap_del_sel = sdhci_am654->otap_del_sel[timing];
 
 	mask = OTAPDLYENA_MASK | OTAPDLYSEL_MASK;
 	val = (0x1 << OTAPDLYENA_SHIFT) |
 	      (otap_del_sel << OTAPDLYSEL_SHIFT);
-	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, mask, val);
 
+	/* Setup Input TAP delay */
+	itap_del_ena = sdhci_am654->itap_del_ena[timing];
+	itap_del_sel = sdhci_am654->itap_del_sel[timing];
+
+	mask |= ITAPDLYENA_MASK | ITAPDLYSEL_MASK;
+	val |= (itap_del_ena << ITAPDLYENA_SHIFT) |
+	       (itap_del_sel << ITAPDLYSEL_SHIFT);
+
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPCHGWIN_MASK,
+			   1 << ITAPCHGWIN_SHIFT);
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, mask, val);
+	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPCHGWIN_MASK, 0);
 	regmap_update_bits(sdhci_am654->base, PHY_CTRL5, CLKBUFSEL_MASK,
 			   sdhci_am654->clkbuf_sel);
 
@@ -347,8 +375,6 @@
 		 */
 		case MMC_TIMING_SD_HS:
 		case MMC_TIMING_MMC_HS:
-		case MMC_TIMING_UHS_SDR12:
-		case MMC_TIMING_UHS_SDR25:
 			val &= ~SDHCI_CTRL_HISPD;
 		}
 	}
@@ -365,7 +391,22 @@
 					MAX_POWER_ON_TIMEOUT, false, host, val,
 					reg);
 		if (ret)
-			dev_warn(mmc_dev(host->mmc), "Power on failed\n");
+			dev_info(mmc_dev(host->mmc), "Power on failed\n");
+	}
+}
+
+static void sdhci_am654_reset(struct sdhci_host *host, u8 mask)
+{
+	u8 ctrl;
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
+
+	sdhci_and_cqhci_reset(host, mask);
+
+	if (sdhci_am654->quirks & SDHCI_AM654_QUIRK_FORCE_CDTEST) {
+		ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
+		ctrl |= SDHCI_CTRL_CDTEST_INS | SDHCI_CTRL_CDTEST_EN;
+		sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 	}
 }
 
@@ -398,40 +439,105 @@
 	return 0;
 }
 
-#define ITAP_MAX	32
+#define ITAPDLY_LENGTH 32
+#define ITAPDLY_LAST_INDEX (ITAPDLY_LENGTH - 1)
+
+static u32 sdhci_am654_calculate_itap(struct sdhci_host *host, struct window
+			  *fail_window, u8 num_fails, bool circular_buffer)
+{
+	u8 itap = 0, start_fail = 0, end_fail = 0, pass_length = 0;
+	u8 first_fail_start = 0, last_fail_end = 0;
+	struct device *dev = mmc_dev(host->mmc);
+	struct window pass_window = {0, 0, 0};
+	int prev_fail_end = -1;
+	u8 i;
+
+	if (!num_fails)
+		return ITAPDLY_LAST_INDEX >> 1;
+
+	if (fail_window->length == ITAPDLY_LENGTH) {
+		dev_err(dev, "No passing ITAPDLY, return 0\n");
+		return 0;
+	}
+
+	first_fail_start = fail_window->start;
+	last_fail_end = fail_window[num_fails - 1].end;
+
+	for (i = 0; i < num_fails; i++) {
+		start_fail = fail_window[i].start;
+		end_fail = fail_window[i].end;
+		pass_length = start_fail - (prev_fail_end + 1);
+
+		if (pass_length > pass_window.length) {
+			pass_window.start = prev_fail_end + 1;
+			pass_window.length = pass_length;
+		}
+		prev_fail_end = end_fail;
+	}
+
+	if (!circular_buffer)
+		pass_length = ITAPDLY_LAST_INDEX - last_fail_end;
+	else
+		pass_length = ITAPDLY_LAST_INDEX - last_fail_end + first_fail_start;
+
+	if (pass_length > pass_window.length) {
+		pass_window.start = last_fail_end + 1;
+		pass_window.length = pass_length;
+	}
+
+	if (!circular_buffer)
+		itap = pass_window.start + (pass_window.length >> 1);
+	else
+		itap = (pass_window.start + (pass_window.length >> 1)) % ITAPDLY_LENGTH;
+
+	return (itap > ITAPDLY_LAST_INDEX) ? ITAPDLY_LAST_INDEX >> 1 : itap;
+}
+
 static int sdhci_am654_platform_execute_tuning(struct sdhci_host *host,
 					       u32 opcode)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
-	int cur_val, prev_val = 1, fail_len = 0, pass_window = 0, pass_len;
-	u32 itap;
+	unsigned char timing = host->mmc->ios.timing;
+	struct window fail_window[ITAPDLY_LENGTH];
+	u8 curr_pass, itap;
+	u8 fail_index = 0;
+	u8 prev_pass = 1;
+
+	memset(fail_window, 0, sizeof(fail_window));
 
 	/* Enable ITAPDLY */
-	regmap_update_bits(sdhci_am654->base, PHY_CTRL4, ITAPDLYENA_MASK,
-			   1 << ITAPDLYENA_SHIFT);
+	sdhci_am654->itap_del_ena[timing] = 0x1;
+
+	for (itap = 0; itap < ITAPDLY_LENGTH; itap++) {
+		sdhci_am654_write_itapdly(sdhci_am654, itap, sdhci_am654->itap_del_ena[timing]);
 
-	for (itap = 0; itap < ITAP_MAX; itap++) {
-		sdhci_am654_write_itapdly(sdhci_am654, itap);
+		curr_pass = !mmc_send_tuning(host->mmc, opcode, NULL);
 
-		cur_val = !mmc_send_tuning(host->mmc, opcode, NULL);
-		if (cur_val && !prev_val)
-			pass_window = itap;
+		if (!curr_pass && prev_pass)
+			fail_window[fail_index].start = itap;
 
-		if (!cur_val)
-			fail_len++;
+		if (!curr_pass) {
+			fail_window[fail_index].end = itap;
+			fail_window[fail_index].length++;
+		}
+
+		if (curr_pass && !prev_pass)
+			fail_index++;
 
-		prev_val = cur_val;
+		prev_pass = curr_pass;
 	}
-	/*
-	 * Having determined the length of the failing window and start of
-	 * the passing window calculate the length of the passing window and
-	 * set the final value halfway through it considering the range as a
-	 * circular buffer
-	 */
-	pass_len = ITAP_MAX - fail_len;
-	itap = (pass_window + (pass_len >> 1)) % ITAP_MAX;
-	sdhci_am654_write_itapdly(sdhci_am654, itap);
+
+	if (fail_window[fail_index].length != 0)
+		fail_index++;
+
+	itap = sdhci_am654_calculate_itap(host, fail_window, fail_index,
+					  sdhci_am654->dll_enable);
+
+	sdhci_am654_write_itapdly(sdhci_am654, itap, sdhci_am654->itap_del_ena[timing]);
+
+	/* Save ITAPDLY */
+	sdhci_am654->itap_del_sel[timing] = itap;
 
 	return 0;
 }
@@ -446,7 +552,7 @@
 	.set_clock = sdhci_am654_set_clock,
 	.write_b = sdhci_am654_write_b,
 	.irq = sdhci_am654_cqhci_irq,
-	.reset = sdhci_reset,
+	.reset = sdhci_and_cqhci_reset,
 };
 
 static const struct sdhci_pltfm_data sdhci_am654_pdata = {
@@ -476,7 +582,7 @@
 	.set_clock = sdhci_am654_set_clock,
 	.write_b = sdhci_am654_write_b,
 	.irq = sdhci_am654_cqhci_irq,
-	.reset = sdhci_reset,
+	.reset = sdhci_and_cqhci_reset,
 };
 
 static const struct sdhci_pltfm_data sdhci_j721e_8bit_pdata = {
@@ -500,7 +606,7 @@
 	.set_clock = sdhci_j721e_4bit_set_clock,
 	.write_b = sdhci_am654_write_b,
 	.irq = sdhci_am654_cqhci_irq,
-	.reset = sdhci_reset,
+	.reset = sdhci_am654_reset,
 };
 
 static const struct sdhci_pltfm_data sdhci_j721e_4bit_pdata = {
@@ -514,26 +620,6 @@
 	.flags = IOMUX_PRESENT,
 };
 
-static const struct sdhci_pltfm_data sdhci_am64_8bit_pdata = {
-	.ops = &sdhci_j721e_8bit_ops,
-	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
-};
-
-static const struct sdhci_am654_driver_data sdhci_am64_8bit_drvdata = {
-	.pdata = &sdhci_am64_8bit_pdata,
-	.flags = DLL_PRESENT | DLL_CALIB,
-};
-
-static const struct sdhci_pltfm_data sdhci_am64_4bit_pdata = {
-	.ops = &sdhci_j721e_4bit_ops,
-	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
-};
-
-static const struct sdhci_am654_driver_data sdhci_am64_4bit_drvdata = {
-	.pdata = &sdhci_am64_4bit_pdata,
-	.flags = IOMUX_PRESENT,
-};
-
 static const struct soc_device_attribute sdhci_am654_devices[] = {
 	{ .family = "AM65X",
 	  .revision = "SR1.0",
@@ -582,32 +668,15 @@
 	int i;
 	int ret;
 
-	ret = device_property_read_u32(dev, td[MMC_TIMING_LEGACY].otap_binding,
-				 &sdhci_am654->otap_del_sel[MMC_TIMING_LEGACY]);
-	if (ret) {
-		/*
-		 * ti,otap-del-sel-legacy is mandatory, look for old binding
-		 * if not found.
-		 */
-		ret = device_property_read_u32(dev, "ti,otap-del-sel",
-					       &sdhci_am654->otap_del_sel[0]);
-		if (ret) {
-			dev_err(dev, "Couldn't find otap-del-sel\n");
-
-			return ret;
-		}
-
-		dev_info(dev, "Using legacy binding ti,otap-del-sel\n");
-		sdhci_am654->legacy_otapdly = true;
-
-		return 0;
-	}
-
-	for (i = MMC_TIMING_MMC_HS; i <= MMC_TIMING_MMC_HS400; i++) {
+	for (i = MMC_TIMING_LEGACY; i <= MMC_TIMING_MMC_HS400; i++) {
 
 		ret = device_property_read_u32(dev, td[i].otap_binding,
 					       &sdhci_am654->otap_del_sel[i]);
 		if (ret) {
+			if (i == MMC_TIMING_LEGACY) {
+				dev_err(dev, "Couldn't find mandatory ti,otap-del-sel-legacy\n");
+				return ret;
+			}
 			dev_dbg(dev, "Couldn't find %s\n",
 				td[i].otap_binding);
 			/*
@@ -620,9 +689,12 @@
 				host->mmc->caps2 &= ~td[i].capability;
 		}
 
-		if (td[i].itap_binding)
-			device_property_read_u32(dev, td[i].itap_binding,
-						 &sdhci_am654->itap_del_sel[i]);
+		if (td[i].itap_binding) {
+			ret = device_property_read_u32(dev, td[i].itap_binding,
+						       &sdhci_am654->itap_del_sel[i]);
+			if (!ret)
+				sdhci_am654->itap_del_ena[i] = 0x1;
+		}
 	}
 
 	return 0;
@@ -739,6 +811,9 @@
 	device_property_read_u32(dev, "ti,clkbuf-sel",
 				 &sdhci_am654->clkbuf_sel);
 
+	if (device_property_read_bool(dev, "ti,fails-without-test-cd"))
+		sdhci_am654->quirks |= SDHCI_AM654_QUIRK_FORCE_CDTEST;
+
 	sdhci_get_of_property(pdev);
 
 	return 0;
@@ -759,11 +834,11 @@
 	},
 	{
 		.compatible = "ti,am64-sdhci-8bit",
-		.data = &sdhci_am64_8bit_drvdata,
+		.data = &sdhci_j721e_8bit_drvdata,
 	},
 	{
 		.compatible = "ti,am64-sdhci-4bit",
-		.data = &sdhci_am64_4bit_drvdata,
+		.data = &sdhci_j721e_4bit_drvdata,
 	},
 	{ /* sentinel */ }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sdhci_f_sdh30.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sdhci_f_sdh30.c
@@ -26,9 +26,16 @@
 	bool enable_cmd_dat_delay;
 };
 
+static void *sdhci_f_sdhost_priv(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+	return sdhci_pltfm_priv(pltfm_host);
+}
+
 static void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host)
 {
-	struct f_sdhost_priv *priv = sdhci_priv(host);
+	struct f_sdhost_priv *priv = sdhci_f_sdhost_priv(host);
 	u32 ctrl = 0;
 
 	usleep_range(2500, 3000);
@@ -61,7 +68,7 @@
 
 static void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask)
 {
-	struct f_sdhost_priv *priv = sdhci_priv(host);
+	struct f_sdhost_priv *priv = sdhci_f_sdhost_priv(host);
 	u32 ctl;
 
 	if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0)
@@ -85,30 +92,32 @@
 	.set_uhs_signaling = sdhci_set_uhs_signaling,
 };
 
+static const struct sdhci_pltfm_data sdhci_f_sdh30_pltfm_data = {
+	.ops = &sdhci_f_sdh30_ops,
+	.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
+		| SDHCI_QUIRK_INVERTED_WRITE_PROTECT,
+	.quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE
+		|  SDHCI_QUIRK2_TUNING_WORK_AROUND,
+};
+
 static int sdhci_f_sdh30_probe(struct platform_device *pdev)
 {
 	struct sdhci_host *host;
 	struct device *dev = &pdev->dev;
-	int irq, ctrl = 0, ret = 0;
+	int ctrl = 0, ret = 0;
 	struct f_sdhost_priv *priv;
+	struct sdhci_pltfm_host *pltfm_host;
 	u32 reg = 0;
 
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0)
-		return irq;
-
-	host = sdhci_alloc_host(dev, sizeof(struct f_sdhost_priv));
+	host = sdhci_pltfm_init(pdev, &sdhci_f_sdh30_pltfm_data,
+				sizeof(struct f_sdhost_priv));
 	if (IS_ERR(host))
 		return PTR_ERR(host);
 
-	priv = sdhci_priv(host);
+	pltfm_host = sdhci_priv(host);
+	priv = sdhci_pltfm_priv(pltfm_host);
 	priv->dev = dev;
 
-	host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
-		       SDHCI_QUIRK_INVERTED_WRITE_PROTECT;
-	host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE |
-			SDHCI_QUIRK2_TUNING_WORK_AROUND;
-
 	priv->enable_cmd_dat_delay = device_property_read_bool(dev,
 						"fujitsu,cmd-dat-delay-select");
 
@@ -116,18 +125,6 @@
 	if (ret)
 		goto err;
 
-	platform_set_drvdata(pdev, host);
-
-	host->hw_name = "f_sdh30";
-	host->ops = &sdhci_f_sdh30_ops;
-	host->irq = irq;
-
-	host->ioaddr = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(host->ioaddr)) {
-		ret = PTR_ERR(host->ioaddr);
-		goto err;
-	}
-
 	if (dev_of_node(dev)) {
 		sdhci_get_of_property(pdev);
 
@@ -168,6 +165,9 @@
 	if (reg & SDHCI_CAN_DO_8BIT)
 		priv->vendor_hs200 = F_SDH30_EMMC_HS200;
 
+	if (!(reg & SDHCI_TIMEOUT_CLK_MASK))
+		host->quirks |= SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK;
+
 	ret = sdhci_add_host(host);
 	if (ret)
 		goto err_add_host;
@@ -179,23 +179,22 @@
 err_clk:
 	clk_disable_unprepare(priv->clk_iface);
 err:
-	sdhci_free_host(host);
+	sdhci_pltfm_free(pdev);
+
 	return ret;
 }
 
 static int sdhci_f_sdh30_remove(struct platform_device *pdev)
 {
 	struct sdhci_host *host = platform_get_drvdata(pdev);
-	struct f_sdhost_priv *priv = sdhci_priv(host);
-
-	sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) ==
-			  0xffffffff);
+	struct f_sdhost_priv *priv = sdhci_f_sdhost_priv(host);
+	struct clk *clk_iface = priv->clk_iface;
+	struct clk *clk = priv->clk;
 
-	clk_disable_unprepare(priv->clk_iface);
-	clk_disable_unprepare(priv->clk);
+	sdhci_pltfm_unregister(pdev);
 
-	sdhci_free_host(host);
-	platform_set_drvdata(pdev, NULL);
+	clk_disable_unprepare(clk_iface);
+	clk_disable_unprepare(clk);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sh_mmcif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sh_mmcif.c
@@ -1398,7 +1398,7 @@
 	irq[0] = platform_get_irq(pdev, 0);
 	irq[1] = platform_get_irq_optional(pdev, 1);
 	if (irq[0] < 0)
-		return -ENXIO;
+		return irq[0];
 
 	reg = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(reg))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/sunxi-mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/sunxi-mmc.c
@@ -377,8 +377,9 @@
 		pdes[i].buf_addr_ptr1 =
 			cpu_to_le32(sg_dma_address(&data->sg[i]) >>
 				    host->cfg->idma_des_shift);
-		pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc >>
-						    host->cfg->idma_des_shift);
+		pdes[i].buf_addr_ptr2 =
+			cpu_to_le32(next_desc >>
+				    host->cfg->idma_des_shift);
 	}
 
 	pdes[0].config |= cpu_to_le32(SDXC_IDMAC_DES0_FD);
@@ -1167,6 +1168,14 @@
 	.can_calibrate = false,
 };
 
+static const struct sunxi_mmc_cfg sun20i_d1_cfg = {
+	.idma_des_size_bits = 13,
+	.idma_des_shift = 2,
+	.can_calibrate = true,
+	.mask_data0 = true,
+	.needs_new_timings = true,
+};
+
 static const struct sunxi_mmc_cfg sun50i_a64_cfg = {
 	.idma_des_size_bits = 16,
 	.clk_delays = NULL,
@@ -1182,10 +1191,9 @@
 	.needs_new_timings = true,
 };
 
-static const struct sunxi_mmc_cfg sun50i_a100_cfg = {
+static const struct sunxi_mmc_cfg sun50i_h616_cfg = {
 	.idma_des_size_bits = 16,
 	.idma_des_shift = 2,
-	.clk_delays = NULL,
 	.can_calibrate = true,
 	.mask_data0 = true,
 	.needs_new_timings = true,
@@ -1205,10 +1213,12 @@
 	{ .compatible = "allwinner,sun7i-a20-mmc", .data = &sun7i_a20_cfg },
 	{ .compatible = "allwinner,sun8i-a83t-emmc", .data = &sun8i_a83t_emmc_cfg },
 	{ .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
+	{ .compatible = "allwinner,sun20i-d1-mmc", .data = &sun20i_d1_cfg },
 	{ .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
 	{ .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
-	{ .compatible = "allwinner,sun50i-a100-mmc", .data = &sun50i_a100_cfg },
+	{ .compatible = "allwinner,sun50i-a100-mmc", .data = &sun20i_d1_cfg },
 	{ .compatible = "allwinner,sun50i-a100-emmc", .data = &sun50i_a100_emmc_cfg },
+	{ .compatible = "allwinner,sun50i-h616-mmc", .data = &sun50i_h616_cfg },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
@@ -1340,8 +1350,8 @@
 		return ret;
 
 	host->irq = platform_get_irq(pdev, 0);
-	if (host->irq <= 0) {
-		ret = -EINVAL;
+	if (host->irq < 0) {
+		ret = host->irq;
 		goto error_disable_mmc;
 	}
 
@@ -1482,9 +1492,11 @@
 	struct sunxi_mmc_host *host = mmc_priv(mmc);
 
 	mmc_remove_host(mmc);
-	pm_runtime_force_suspend(&pdev->dev);
-	disable_irq(host->irq);
-	sunxi_mmc_disable(host);
+	pm_runtime_disable(&pdev->dev);
+	if (!pm_runtime_status_suspended(&pdev->dev)) {
+		disable_irq(host->irq);
+		sunxi_mmc_disable(host);
+	}
 	dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
 	mmc_free_host(mmc);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/tmio_mmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/tmio_mmc.c
@@ -75,7 +75,7 @@
 	tmio_mmc_clk_start(host);
 }
 
-static void tmio_mmc_reset(struct tmio_mmc_host *host)
+static void tmio_mmc_reset(struct tmio_mmc_host *host, bool preserve)
 {
 	sd_ctrl_write16(host, CTL_RESET_SDIO, 0x0000);
 	usleep_range(10000, 11000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/tmio_mmc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/tmio_mmc.h
@@ -42,6 +42,7 @@
 #define CTL_DMA_ENABLE 0xd8
 #define CTL_RESET_SD 0xe0
 #define CTL_VERSION 0xe2
+#define CTL_SDIF_MODE 0xe6 /* only known on R-Car 2+ */
 
 /* Definitions for values the CTL_STOP_INTERNAL_ACTION register can take */
 #define TMIO_STOP_STP		BIT(0)
@@ -98,6 +99,9 @@
 /* Definitions for values the CTL_DMA_ENABLE register can take */
 #define DMA_ENABLE_DMASDRW	BIT(1)
 
+/* Definitions for values the CTL_SDIF_MODE register can take */
+#define SDIF_MODE_HS400		BIT(0) /* only known on R-Car 2+ */
+
 /* Define some IRQ masks */
 /* This is the mask used at reset by the chip */
 #define TMIO_MASK_ALL           0x837f031d
@@ -181,7 +185,7 @@
 	int (*multi_io_quirk)(struct mmc_card *card,
 			      unsigned int direction, int blk_size);
 	int (*write16_hook)(struct tmio_mmc_host *host, int addr);
-	void (*reset)(struct tmio_mmc_host *host);
+	void (*reset)(struct tmio_mmc_host *host, bool preserve);
 	bool (*check_retune)(struct tmio_mmc_host *host, struct mmc_request *mrq);
 	void (*fixup_request)(struct tmio_mmc_host *host, struct mmc_request *mrq);
 	unsigned int (*get_timeout_cycles)(struct tmio_mmc_host *host);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/tmio_mmc_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/tmio_mmc_core.c
@@ -179,8 +179,17 @@
 	sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, reg);
 }
 
-static void tmio_mmc_reset(struct tmio_mmc_host *host)
+static void tmio_mmc_reset(struct tmio_mmc_host *host, bool preserve)
 {
+	u16 card_opt, clk_ctrl, sdif_mode;
+
+	if (preserve) {
+		card_opt = sd_ctrl_read16(host, CTL_SD_MEM_CARD_OPT);
+		clk_ctrl = sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL);
+		if (host->pdata->flags & TMIO_MMC_MIN_RCAR2)
+			sdif_mode = sd_ctrl_read16(host, CTL_SDIF_MODE);
+	}
+
 	/* FIXME - should we set stop clock reg here */
 	sd_ctrl_write16(host, CTL_RESET_SD, 0x0000);
 	usleep_range(10000, 11000);
@@ -190,7 +199,7 @@
 	tmio_mmc_abort_dma(host);
 
 	if (host->reset)
-		host->reset(host);
+		host->reset(host, preserve);
 
 	sd_ctrl_write32_as_16_and_16(host, CTL_IRQ_MASK, host->sdcard_irq_mask_all);
 	host->sdcard_irq_mask = host->sdcard_irq_mask_all;
@@ -206,6 +215,13 @@
 		sd_ctrl_write16(host, CTL_TRANSACTION_CTL, 0x0001);
 	}
 
+	if (preserve) {
+		sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, card_opt);
+		sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk_ctrl);
+		if (host->pdata->flags & TMIO_MMC_MIN_RCAR2)
+			sd_ctrl_write16(host, CTL_SDIF_MODE, sdif_mode);
+	}
+
 	if (host->mmc->card)
 		mmc_retune_needed(host->mmc);
 }
@@ -243,12 +259,14 @@
 	else
 		mrq->cmd->error = -ETIMEDOUT;
 
+	/* No new calls yet, but disallow concurrent tmio_mmc_done_work() */
+	host->mrq = ERR_PTR(-EBUSY);
 	host->cmd = NULL;
 	host->data = NULL;
 
 	spin_unlock_irqrestore(&host->lock, flags);
 
-	tmio_mmc_reset(host);
+	tmio_mmc_reset(host, true);
 
 	/* Ready for new calls */
 	host->mrq = NULL;
@@ -960,14 +978,8 @@
 	case MMC_POWER_OFF:
 		tmio_mmc_power_off(host);
 		/* For R-Car Gen2+, we need to reset SDHI specific SCC */
-		if (host->pdata->flags & TMIO_MMC_MIN_RCAR2) {
-			host->reset(host);
-
-			if (host->native_hotplug)
-				tmio_mmc_enable_mmc_irqs(host,
-						TMIO_STAT_CARD_REMOVE |
-						TMIO_STAT_CARD_INSERT);
-		}
+		if (host->pdata->flags & TMIO_MMC_MIN_RCAR2)
+			tmio_mmc_reset(host, false);
 
 		host->set_clock(host, 0);
 		break;
@@ -1175,6 +1187,7 @@
 	if (mmc_can_gpio_cd(mmc))
 		_host->ops.get_cd = mmc_gpio_get_cd;
 
+	/* must be set before tmio_mmc_reset() */
 	_host->native_hotplug = !(mmc_can_gpio_cd(mmc) ||
 				  mmc->caps & MMC_CAP_NEEDS_POLL ||
 				  !mmc_card_is_removable(mmc));
@@ -1194,7 +1207,7 @@
 		_host->sdcard_irq_mask_all = TMIO_MASK_ALL;
 
 	_host->set_clock(_host, 0);
-	tmio_mmc_reset(_host);
+	tmio_mmc_reset(_host, false);
 
 	spin_lock_init(&_host->lock);
 	mutex_init(&_host->ios_lock);
@@ -1290,15 +1303,11 @@
 	struct tmio_mmc_host *host = dev_get_drvdata(dev);
 
 	tmio_mmc_clk_enable(host);
-	tmio_mmc_reset(host);
+	tmio_mmc_reset(host, false);
 
 	if (host->clk_cache)
 		host->set_clock(host, host->clk_cache);
 
-	if (host->native_hotplug)
-		tmio_mmc_enable_mmc_irqs(host,
-				TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
-
 	tmio_mmc_enable_dma(host, true);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/toshsd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/toshsd.c
@@ -651,7 +651,9 @@
 	if (ret)
 		goto unmap;
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto free_irq;
 
 	base = pci_resource_start(pdev, 0);
 	dev_dbg(&pdev->dev, "MMIO %pa, IRQ %d\n", &base, pdev->irq);
@@ -660,6 +662,8 @@
 
 	return 0;
 
+free_irq:
+	free_irq(pdev->irq, host);
 unmap:
 	pci_iounmap(pdev, host->ioaddr);
 release:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/usdhi6rol0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/usdhi6rol0.c
@@ -1757,8 +1757,10 @@
 	irq_cd = platform_get_irq_byname(pdev, "card detect");
 	irq_sd = platform_get_irq_byname(pdev, "data");
 	irq_sdio = platform_get_irq_byname(pdev, "SDIO");
-	if (irq_sd < 0 || irq_sdio < 0)
-		return -ENODEV;
+	if (irq_sd < 0)
+		return irq_sd;
+	if (irq_sdio < 0)
+		return irq_sdio;
 
 	mmc = mmc_alloc_host(sizeof(struct usdhi6_host), dev);
 	if (!mmc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/via-sdmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/via-sdmmc.c
@@ -1151,7 +1151,9 @@
 	    pcidev->subsystem_device == 0x3891)
 		sdhost->quirks = VIA_CRDR_QUIRK_300MS_PWRDELAY;
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto unmap;
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/vub300.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/vub300.c
@@ -1715,6 +1715,9 @@
 	int bytes = 3 & less_cmd;
 	int words = less_cmd >> 2;
 	u8 *r = vub300->resp.response.command_response;
+
+	if (!resp_len)
+		return;
 	if (bytes == 3) {
 		cmd->resp[words] = (r[1 + (words << 2)] << 24)
 			| (r[2 + (words << 2)] << 16)
@@ -2049,6 +2052,7 @@
 		return;
 	kref_get(&vub300->kref);
 	if (enable) {
+		set_current_state(TASK_RUNNING);
 		mutex_lock(&vub300->irq_mutex);
 		if (vub300->irqs_queued) {
 			vub300->irqs_queued -= 1;
@@ -2064,6 +2068,7 @@
 			vub300_queue_poll_work(vub300, 0);
 		}
 		mutex_unlock(&vub300->irq_mutex);
+		set_current_state(TASK_INTERRUPTIBLE);
 	} else {
 		vub300->irq_enabled = 0;
 	}
@@ -2299,14 +2304,15 @@
 				0x0000, 0x0000, &vub300->system_port_status,
 				sizeof(vub300->system_port_status), 1000);
 	if (retval < 0) {
-		goto error4;
+		goto error5;
 	} else if (sizeof(vub300->system_port_status) == retval) {
 		vub300->card_present =
 			(0x0001 & vub300->system_port_status.port_flags) ? 1 : 0;
 		vub300->read_only =
 			(0x0010 & vub300->system_port_status.port_flags) ? 1 : 0;
 	} else {
-		goto error4;
+		retval = -EINVAL;
+		goto error5;
 	}
 	usb_set_intfdata(interface, vub300);
 	INIT_DELAYED_WORK(&vub300->pollwork, vub300_pollwork_thread);
@@ -2329,8 +2335,13 @@
 			 "USB vub300 remote SDIO host controller[%d]"
 			 "connected with no SD/SDIO card inserted\n",
 			 interface_to_InterfaceNumber(interface));
-	mmc_add_host(mmc);
+	retval = mmc_add_host(mmc);
+	if (retval)
+		goto error6;
+
 	return 0;
+error6:
+	del_timer_sync(&vub300->inactivity_timer);
 error5:
 	mmc_free_host(mmc);
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/wbsd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/wbsd.c
@@ -1698,7 +1698,15 @@
 	 */
 	wbsd_init_device(host);
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret) {
+		if (!pnp)
+			wbsd_chip_poweroff(host);
+
+		wbsd_release_resources(host);
+		wbsd_free_mmc(dev);
+		return ret;
+	}
 
 	pr_info("%s: W83L51xD", mmc_hostname(mmc));
 	if (host->chip_id != 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mmc/host/wmt-sdmmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mmc/host/wmt-sdmmc.c
@@ -849,7 +849,7 @@
 	if (IS_ERR(priv->clk_sdmmc)) {
 		dev_err(&pdev->dev, "Error getting clock\n");
 		ret = PTR_ERR(priv->clk_sdmmc);
-		goto fail5;
+		goto fail5_and_a_half;
 	}
 
 	ret = clk_prepare_enable(priv->clk_sdmmc);
@@ -859,13 +859,20 @@
 	/* configure the controller to a known 'ready' state */
 	wmt_reset_hardware(mmc);
 
-	mmc_add_host(mmc);
+	ret = mmc_add_host(mmc);
+	if (ret)
+		goto fail7;
 
 	dev_info(&pdev->dev, "WMT SDHC Controller initialized\n");
 
 	return 0;
+fail7:
+	clk_disable_unprepare(priv->clk_sdmmc);
 fail6:
 	clk_put(priv->clk_sdmmc);
+fail5_and_a_half:
+	dma_free_coherent(&pdev->dev, mmc->max_blk_count * 16,
+			  priv->dma_desc_buffer, priv->dma_desc_device_addr);
 fail5:
 	free_irq(dma_irq, priv);
 fail4:
@@ -882,7 +889,6 @@
 {
 	struct mmc_host *mmc;
 	struct wmt_mci_priv *priv;
-	struct resource *res;
 	u32 reg_tmp;
 
 	mmc = platform_get_drvdata(pdev);
@@ -910,9 +916,6 @@
 	clk_disable_unprepare(priv->clk_sdmmc);
 	clk_put(priv->clk_sdmmc);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(res->start, resource_size(res));
-
 	mmc_free_host(mmc);
 
 	dev_info(&pdev->dev, "WMT MCI device removed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/most/most_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/most/most_usb.c
@@ -149,7 +149,8 @@
 	retval = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
 				 DRCI_READ_REQ, req_type,
 				 0x0000,
-				 reg, dma_buf, sizeof(*dma_buf), 5 * HZ);
+				 reg, dma_buf, sizeof(*dma_buf),
+				 USB_CTRL_GET_TIMEOUT);
 	*buf = le16_to_cpu(*dma_buf);
 	kfree(dma_buf);
 
@@ -176,7 +177,7 @@
 			       reg,
 			       NULL,
 			       0,
-			       5 * HZ);
+			       USB_CTRL_SET_TIMEOUT);
 }
 
 static inline int start_sync_ep(struct usb_device *usb_dev, u16 ep)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/chips/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/chips/Kconfig
@@ -55,12 +55,14 @@
 	  LITTLE_ENDIAN_BYTE, if the bytes are reversed.
 
 config MTD_CFI_NOSWAP
+	depends on !ARCH_IXP4XX || CPU_BIG_ENDIAN
 	bool "NO"
 
 config MTD_CFI_BE_BYTE_SWAP
 	bool "BIG_ENDIAN_BYTE"
 
 config MTD_CFI_LE_BYTE_SWAP
+	depends on !ARCH_IXP4XX
 	bool "LITTLE_ENDIAN_BYTE"
 
 endchoice
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/chips/cfi_cmdset_0001.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/chips/cfi_cmdset_0001.c
@@ -421,9 +421,25 @@
 		extra_size = 0;
 
 		/* Protection Register info */
-		if (extp->NumProtectionFields)
+		if (extp->NumProtectionFields) {
+			struct cfi_intelext_otpinfo *otp =
+				(struct cfi_intelext_otpinfo *)&extp->extra[0];
+
 			extra_size += (extp->NumProtectionFields - 1) *
-				      sizeof(struct cfi_intelext_otpinfo);
+				sizeof(struct cfi_intelext_otpinfo);
+
+			if (extp_size >= sizeof(*extp) + extra_size) {
+				int i;
+
+				/* Do some byteswapping if necessary */
+				for (i = 0; i < extp->NumProtectionFields - 1; i++) {
+					otp->ProtRegAddr = le32_to_cpu(otp->ProtRegAddr);
+					otp->FactGroups = le16_to_cpu(otp->FactGroups);
+					otp->UserGroups = le16_to_cpu(otp->UserGroups);
+					otp++;
+				}
+			}
+		}
 	}
 
 	if (extp->MinorVersion >= '1') {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/chips/cfi_cmdset_0002.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -59,6 +59,10 @@
 #define CFI_SR_WBASB		BIT(3)
 #define CFI_SR_SLSB		BIT(1)
 
+enum cfi_quirks {
+	CFI_QUIRK_DQ_TRUE_DATA = BIT(0),
+};
+
 static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
 static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
 #if !FORCE_WORD_WRITE
@@ -436,6 +440,15 @@
 		mtd->name);
 }
 
+static void fixup_quirks(struct mtd_info *mtd)
+{
+	struct map_info *map = mtd->priv;
+	struct cfi_private *cfi = map->fldrv_priv;
+
+	if (cfi->mfr == CFI_MFR_AMD && cfi->id == 0x0c01)
+		cfi->quirks |= CFI_QUIRK_DQ_TRUE_DATA;
+}
+
 /* Used to fix CFI-Tables of chips without Extended Query Tables */
 static struct cfi_fixup cfi_nopri_fixup_table[] = {
 	{ CFI_MFR_SST, 0x234a, fixup_sst39vf }, /* SST39VF1602 */
@@ -474,6 +487,7 @@
 #if !FORCE_WORD_WRITE
 	{ CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers },
 #endif
+	{ CFI_MFR_ANY, CFI_ID_ANY, fixup_quirks },
 	{ 0, 0, NULL }
 };
 static struct cfi_fixup jedec_fixup_table[] = {
@@ -802,21 +816,25 @@
 }
 
 /*
- * Return true if the chip is ready.
+ * Return true if the chip is ready and has the correct value.
  *
  * Ready is one of: read mode, query mode, erase-suspend-read mode (in any
  * non-suspended sector) and is indicated by no toggle bits toggling.
  *
+ * Error are indicated by toggling bits or bits held with the wrong value,
+ * or with bits toggling.
+ *
  * Note that anything more complicated than checking if no bits are toggling
  * (including checking DQ5 for an error status) is tricky to get working
  * correctly and is therefore not done	(particularly with interleaved chips
  * as each chip must be checked independently of the others).
  */
 static int __xipram chip_ready(struct map_info *map, struct flchip *chip,
-			       unsigned long addr)
+			       unsigned long addr, map_word *expected)
 {
 	struct cfi_private *cfi = map->fldrv_priv;
 	map_word d, t;
+	int ret;
 
 	if (cfi_use_status_reg(cfi)) {
 		map_word ready = CMD(CFI_SR_DRB);
@@ -826,57 +844,32 @@
 		 */
 		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, chip->start, map, cfi,
 				 cfi->device_type, NULL);
-		d = map_read(map, addr);
+		t = map_read(map, addr);
 
-		return map_word_andequal(map, d, ready, ready);
+		return map_word_andequal(map, t, ready, ready);
 	}
 
 	d = map_read(map, addr);
 	t = map_read(map, addr);
 
-	return map_word_equal(map, d, t);
+	ret = map_word_equal(map, d, t);
+
+	if (!ret || !expected)
+		return ret;
+
+	return map_word_equal(map, t, *expected);
 }
 
-/*
- * Return true if the chip is ready and has the correct value.
- *
- * Ready is one of: read mode, query mode, erase-suspend-read mode (in any
- * non-suspended sector) and it is indicated by no bits toggling.
- *
- * Error are indicated by toggling bits or bits held with the wrong value,
- * or with bits toggling.
- *
- * Note that anything more complicated than checking if no bits are toggling
- * (including checking DQ5 for an error status) is tricky to get working
- * correctly and is therefore not done	(particularly with interleaved chips
- * as each chip must be checked independently of the others).
- *
- */
 static int __xipram chip_good(struct map_info *map, struct flchip *chip,
-			      unsigned long addr, map_word expected)
+			      unsigned long addr, map_word *expected)
 {
 	struct cfi_private *cfi = map->fldrv_priv;
-	map_word oldd, curd;
-
-	if (cfi_use_status_reg(cfi)) {
-		map_word ready = CMD(CFI_SR_DRB);
-
-		/*
-		 * For chips that support status register, check device
-		 * ready bit
-		 */
-		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, chip->start, map, cfi,
-				 cfi->device_type, NULL);
-		curd = map_read(map, addr);
-
-		return map_word_andequal(map, curd, ready, ready);
-	}
+	map_word *datum = expected;
 
-	oldd = map_read(map, addr);
-	curd = map_read(map, addr);
+	if (cfi->quirks & CFI_QUIRK_DQ_TRUE_DATA)
+		datum = NULL;
 
-	return	map_word_equal(map, oldd, curd) &&
-		map_word_equal(map, curd, expected);
+	return chip_ready(map, chip, addr, datum);
 }
 
 static int get_chip(struct map_info *map, struct flchip *chip, unsigned long adr, int mode)
@@ -893,7 +886,7 @@
 
 	case FL_STATUS:
 		for (;;) {
-			if (chip_ready(map, chip, adr))
+			if (chip_ready(map, chip, adr, NULL))
 				break;
 
 			if (time_after(jiffies, timeo)) {
@@ -932,7 +925,7 @@
 		chip->state = FL_ERASE_SUSPENDING;
 		chip->erase_suspended = 1;
 		for (;;) {
-			if (chip_ready(map, chip, adr))
+			if (chip_ready(map, chip, adr, NULL))
 				break;
 
 			if (time_after(jiffies, timeo)) {
@@ -1463,7 +1456,7 @@
 	/* wait for chip to become ready */
 	timeo = jiffies + msecs_to_jiffies(2);
 	for (;;) {
-		if (chip_ready(map, chip, adr))
+		if (chip_ready(map, chip, adr, NULL))
 			break;
 
 		if (time_after(jiffies, timeo)) {
@@ -1699,7 +1692,7 @@
 		 * "chip_good" to avoid the failure due to scheduling.
 		 */
 		if (time_after(jiffies, timeo) &&
-		    !chip_good(map, chip, adr, datum)) {
+		    !chip_good(map, chip, adr, &datum)) {
 			xip_enable(map, chip, adr);
 			printk(KERN_WARNING "MTD %s(): software timeout\n", __func__);
 			xip_disable(map, chip, adr);
@@ -1707,7 +1700,7 @@
 			break;
 		}
 
-		if (chip_good(map, chip, adr, datum)) {
+		if (chip_good(map, chip, adr, &datum)) {
 			if (cfi_check_err_status(map, chip, adr))
 				ret = -EIO;
 			break;
@@ -1979,14 +1972,14 @@
 		 * "chip_good" to avoid the failure due to scheduling.
 		 */
 		if (time_after(jiffies, timeo) &&
-		    !chip_good(map, chip, adr, datum)) {
+		    !chip_good(map, chip, adr, &datum)) {
 			pr_err("MTD %s(): software timeout, address:0x%.8lx.\n",
 			       __func__, adr);
 			ret = -EIO;
 			break;
 		}
 
-		if (chip_good(map, chip, adr, datum)) {
+		if (chip_good(map, chip, adr, &datum)) {
 			if (cfi_check_err_status(map, chip, adr))
 				ret = -EIO;
 			break;
@@ -2195,7 +2188,7 @@
 	 * If the driver thinks the chip is idle, and no toggle bits
 	 * are changing, then the chip is actually idle for sure.
 	 */
-	if (chip->state == FL_READY && chip_ready(map, chip, adr))
+	if (chip->state == FL_READY && chip_ready(map, chip, adr, NULL))
 		return 0;
 
 	/*
@@ -2212,7 +2205,7 @@
 
 		/* wait for the chip to become ready */
 		for (i = 0; i < jiffies_to_usecs(timeo); i++) {
-			if (chip_ready(map, chip, adr))
+			if (chip_ready(map, chip, adr, NULL))
 				return 0;
 
 			udelay(1);
@@ -2276,13 +2269,13 @@
 	map_write(map, datum, adr);
 
 	for (i = 0; i < jiffies_to_usecs(uWriteTimeout); i++) {
-		if (chip_ready(map, chip, adr))
+		if (chip_ready(map, chip, adr, NULL))
 			break;
 
 		udelay(1);
 	}
 
-	if (!chip_good(map, chip, adr, datum) ||
+	if (!chip_ready(map, chip, adr, &datum) ||
 	    cfi_check_err_status(map, chip, adr)) {
 		/* reset on all failures. */
 		map_write(map, CMD(0xF0), chip->start);
@@ -2424,6 +2417,7 @@
 	DECLARE_WAITQUEUE(wait, current);
 	int ret;
 	int retry_cnt = 0;
+	map_word datum = map_word_ff(map);
 
 	adr = cfi->addr_unlock1;
 
@@ -2478,7 +2472,7 @@
 			chip->erase_suspended = 0;
 		}
 
-		if (chip_good(map, chip, adr, map_word_ff(map))) {
+		if (chip_ready(map, chip, adr, &datum)) {
 			if (cfi_check_err_status(map, chip, adr))
 				ret = -EIO;
 			break;
@@ -2523,6 +2517,7 @@
 	DECLARE_WAITQUEUE(wait, current);
 	int ret;
 	int retry_cnt = 0;
+	map_word datum = map_word_ff(map);
 
 	adr += chip->start;
 
@@ -2577,7 +2572,7 @@
 			chip->erase_suspended = 0;
 		}
 
-		if (chip_good(map, chip, adr, map_word_ff(map))) {
+		if (chip_ready(map, chip, adr, &datum)) {
 			if (cfi_check_err_status(map, chip, adr))
 				ret = -EIO;
 			break;
@@ -2771,7 +2766,7 @@
 	 */
 	timeo = jiffies + msecs_to_jiffies(2000);	/* 2s max (un)locking */
 	for (;;) {
-		if (chip_ready(map, chip, adr))
+		if (chip_ready(map, chip, adr, NULL))
 			break;
 
 		if (time_after(jiffies, timeo)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/chips/cfi_probe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/chips/cfi_probe.c
@@ -198,6 +198,9 @@
 	__u32 base = 0;
 	int num_erase_regions = cfi_read_query(map, base + (0x10 + 28)*ofs_factor);
 	int i;
+	int extendedId1 = 0;
+	int extendedId2 = 0;
+	int extendedId3 = 0;
 	int addr_unlock1 = 0x555, addr_unlock2 = 0x2AA;
 
 	xip_enable(base, map, cfi);
@@ -222,6 +225,38 @@
 	for (i=0; i<(sizeof(struct cfi_ident) + num_erase_regions * 4); i++)
 		((unsigned char *)cfi->cfiq)[i] = cfi_read_query(map,base + (0x10 + i)*ofs_factor);
 
+	/* Note we put the device back into Read Mode BEFORE going into Auto
+	 * Select Mode, as some devices support nesting of modes, others
+	 * don't. This way should always work.
+	 * On cmdset 0001 the writes of 0xaa and 0x55 are not needed, and
+	 * so should be treated as nops or illegal (and so put the device
+	 * back into Read Mode, which is a nop in this case).
+	 */
+	cfi_send_gen_cmd(0xf0,     0, base, map, cfi, cfi->device_type, NULL);
+	cfi_send_gen_cmd(0xaa, 0x555, base, map, cfi, cfi->device_type, NULL);
+	cfi_send_gen_cmd(0x55, 0x2aa, base, map, cfi, cfi->device_type, NULL);
+	cfi_send_gen_cmd(0x90, 0x555, base, map, cfi, cfi->device_type, NULL);
+	cfi->mfr = cfi_read_query16(map, base);
+	cfi->id = cfi_read_query16(map, base + ofs_factor);
+
+	/* Get device ID cycle 1,2,3 for Numonyx/ST devices */
+	if ((cfi->mfr == CFI_MFR_INTEL || cfi->mfr == CFI_MFR_ST)
+		&& ((cfi->id & 0xff) == 0x7e)
+		&& (le16_to_cpu(cfi->cfiq->P_ID) == 0x0002)) {
+		extendedId1 = cfi_read_query16(map, base + 0x1 * ofs_factor);
+		extendedId2 = cfi_read_query16(map, base + 0xe * ofs_factor);
+		extendedId3 = cfi_read_query16(map, base + 0xf * ofs_factor);
+	}
+
+	/* Get AMD/Spansion extended JEDEC ID */
+	if (cfi->mfr == CFI_MFR_AMD && (cfi->id & 0xff) == 0x7e)
+		cfi->id = cfi_read_query(map, base + 0xe * ofs_factor) << 8 |
+			  cfi_read_query(map, base + 0xf * ofs_factor);
+
+	/* Put it back into Read Mode */
+	cfi_qry_mode_off(base, map, cfi);
+	xip_allowed(base, map);
+
 	/* Do any necessary byteswapping */
 	cfi->cfiq->P_ID = le16_to_cpu(cfi->cfiq->P_ID);
 
@@ -231,6 +266,16 @@
 	cfi->cfiq->InterfaceDesc = le16_to_cpu(cfi->cfiq->InterfaceDesc);
 	cfi->cfiq->MaxBufWriteSize = le16_to_cpu(cfi->cfiq->MaxBufWriteSize);
 
+   /* If the device is a M29EW used in 8-bit mode, adjust buffer size */
+	if ((cfi->cfiq->MaxBufWriteSize > 0x8) && (cfi->mfr == CFI_MFR_INTEL ||
+		 cfi->mfr == CFI_MFR_ST) && (extendedId1 == 0x7E) &&
+		 (extendedId2 == 0x22 || extendedId2 == 0x23 || extendedId2 == 0x28) &&
+		 (extendedId3 == 0x01)) {
+		cfi->cfiq->MaxBufWriteSize = 0x8;
+		pr_warn("Adjusted buffer size on Numonyx flash M29EW family");
+		pr_warn("in 8 bit mode\n");
+    }
+
 #ifdef DEBUG_CFI
 	/* Dump the information therein */
 	print_cfi_ident(cfi->cfiq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/docg3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/docg3.c
@@ -1974,9 +1974,14 @@
 		dev_err(dev, "No I/O memory resource defined\n");
 		return ret;
 	}
-	base = devm_ioremap(dev, ress->start, DOC_IOSPACE_SIZE);
 
 	ret = -ENOMEM;
+	base = devm_ioremap(dev, ress->start, DOC_IOSPACE_SIZE);
+	if (!base) {
+		dev_err(dev, "devm_ioremap dev failed\n");
+		return ret;
+	}
+
 	cascade = devm_kcalloc(dev, DOC_MAX_NBFLOORS, sizeof(*cascade),
 			       GFP_KERNEL);
 	if (!cascade)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/mchp23k256.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/mchp23k256.c
@@ -229,6 +229,19 @@
 };
 MODULE_DEVICE_TABLE(of, mchp23k256_of_table);
 
+static const struct spi_device_id mchp23k256_spi_ids[] = {
+	{
+		.name = "mchp23k256",
+		.driver_data = (kernel_ulong_t)&mchp23k256_caps,
+	},
+	{
+		.name = "mchp23lcv1024",
+		.driver_data = (kernel_ulong_t)&mchp23lcv1024_caps,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(spi, mchp23k256_spi_ids);
+
 static struct spi_driver mchp23k256_driver = {
 	.driver = {
 		.name	= "mchp23k256",
@@ -236,6 +249,7 @@
 	},
 	.probe		= mchp23k256_probe,
 	.remove		= mchp23k256_remove,
+	.id_table	= mchp23k256_spi_ids,
 };
 
 module_spi_driver(mchp23k256_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/mchp48l640.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/mchp48l640.c
@@ -357,6 +357,15 @@
 };
 MODULE_DEVICE_TABLE(of, mchp48l640_of_table);
 
+static const struct spi_device_id mchp48l640_spi_ids[] = {
+	{
+		.name = "48l640",
+		.driver_data = (kernel_ulong_t)&mchp48l640_caps,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(spi, mchp48l640_spi_ids);
+
 static struct spi_driver mchp48l640_driver = {
 	.driver = {
 		.name	= "mchp48l640",
@@ -364,6 +373,7 @@
 	},
 	.probe		= mchp48l640_probe,
 	.remove		= mchp48l640_remove,
+	.id_table	= mchp48l640_spi_ids,
 };
 
 module_spi_driver(mchp48l640_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/mtd_dataflash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/mtd_dataflash.c
@@ -96,6 +96,13 @@
 	struct mtd_info		mtd;
 };
 
+static const struct spi_device_id dataflash_dev_ids[] = {
+	{ "at45" },
+	{ "dataflash" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, dataflash_dev_ids);
+
 #ifdef CONFIG_OF
 static const struct of_device_id dataflash_dt_ids[] = {
 	{ .compatible = "atmel,at45", },
@@ -105,6 +112,13 @@
 MODULE_DEVICE_TABLE(of, dataflash_dt_ids);
 #endif
 
+static const struct spi_device_id dataflash_spi_ids[] = {
+	{ .name = "at45", },
+	{ .name = "dataflash", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, dataflash_spi_ids);
+
 /* ......................................................................... */
 
 /*
@@ -927,9 +941,11 @@
 		.name		= "mtd_dataflash",
 		.of_match_table = of_match_ptr(dataflash_dt_ids),
 	},
+	.id_table = dataflash_dev_ids,
 
 	.probe		= dataflash_probe,
 	.remove		= dataflash_remove,
+	.id_table	= dataflash_spi_ids,
 
 	/* FIXME:  investigate suspend and resume... */
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/phram.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/phram.c
@@ -264,15 +264,19 @@
 		}
 	}
 
-	if (erasesize)
-		div_u64_rem(len, (uint32_t)erasesize, &rem);
-
 	if (len == 0 || erasesize == 0 || erasesize > len
-	    || erasesize > UINT_MAX || rem) {
+	    || erasesize > UINT_MAX) {
 		parse_err("illegal erasesize or len\n");
 		ret = -EINVAL;
 		goto error;
 	}
+
+	div_u64_rem(len, (uint32_t)erasesize, &rem);
+	if (rem) {
+		parse_err("len is not multiple of erasesize\n");
+		ret = -EINVAL;
+		goto error;
+	}
 
 	ret = register_device(name, start, len, (uint32_t)erasesize);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/powernv_flash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/powernv_flash.c
@@ -207,6 +207,9 @@
 	 * get them
 	 */
 	mtd->name = devm_kasprintf(dev, GFP_KERNEL, "%pOFP", dev->of_node);
+	if (!mtd->name)
+		return -ENOMEM;
+
 	mtd->type = MTD_NORFLASH;
 	mtd->flags = MTD_WRITEABLE;
 	mtd->size = size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/slram.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/slram.c
@@ -296,10 +296,12 @@
 		T("slram: devname = %s\n", devname);
 		if ((!map) || (!(devstart = strsep(&map, ",")))) {
 			E("slram: No devicestart specified.\n");
+			break;
 		}
 		T("slram: devstart = %s\n", devstart);
 		if ((!map) || (!(devlength = strsep(&map, ",")))) {
 			E("slram: No devicelength / -end specified.\n");
+			break;
 		}
 		T("slram: devlength = %s\n", devlength);
 		if (parse_cmdline(devname, devstart, devlength) != 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/devices/st_spi_fsm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/devices/st_spi_fsm.c
@@ -2115,10 +2115,12 @@
 		(long long)fsm->mtd.size, (long long)(fsm->mtd.size >> 20),
 		fsm->mtd.erasesize, (fsm->mtd.erasesize >> 10));
 
-	return mtd_device_register(&fsm->mtd, NULL, 0);
-
+	ret = mtd_device_register(&fsm->mtd, NULL, 0);
+	if (ret) {
 err_clk_unprepare:
-	clk_disable_unprepare(fsm->clk);
+		clk_disable_unprepare(fsm->clk);
+	}
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/hyperbus/hbmc-am654.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/hyperbus/hbmc-am654.c
@@ -174,26 +174,30 @@
 	priv->hbdev.np = of_get_next_child(np, NULL);
 	ret = of_address_to_resource(priv->hbdev.np, 0, &res);
 	if (ret)
-		return ret;
+		goto put_node;
 
 	if (of_property_read_bool(dev->of_node, "mux-controls")) {
 		struct mux_control *control = devm_mux_control_get(dev, NULL);
 
-		if (IS_ERR(control))
-			return PTR_ERR(control);
+		if (IS_ERR(control)) {
+			ret = PTR_ERR(control);
+			goto put_node;
+		}
 
 		ret = mux_control_select(control, 1);
 		if (ret) {
 			dev_err(dev, "Failed to select HBMC mux\n");
-			return ret;
+			goto put_node;
 		}
 		priv->mux_ctrl = control;
 	}
 
 	priv->hbdev.map.size = resource_size(&res);
 	priv->hbdev.map.virt = devm_ioremap_resource(dev, &res);
-	if (IS_ERR(priv->hbdev.map.virt))
-		return PTR_ERR(priv->hbdev.map.virt);
+	if (IS_ERR(priv->hbdev.map.virt)) {
+		ret = PTR_ERR(priv->hbdev.map.virt);
+		goto disable_mux;
+	}
 
 	priv->ctlr.dev = dev;
 	priv->ctlr.ops = &am654_hbmc_ops;
@@ -226,23 +230,24 @@
 disable_mux:
 	if (priv->mux_ctrl)
 		mux_control_deselect(priv->mux_ctrl);
+put_node:
+	of_node_put(priv->hbdev.np);
 	return ret;
 }
 
-static int am654_hbmc_remove(struct platform_device *pdev)
+static void am654_hbmc_remove(struct platform_device *pdev)
 {
 	struct am654_hbmc_priv *priv = platform_get_drvdata(pdev);
 	struct am654_hbmc_device_priv *dev_priv = priv->hbdev.priv;
-	int ret;
 
-	ret = hyperbus_unregister_device(&priv->hbdev);
+	hyperbus_unregister_device(&priv->hbdev);
+
 	if (priv->mux_ctrl)
 		mux_control_deselect(priv->mux_ctrl);
 
 	if (dev_priv->rx_chan)
 		dma_release_channel(dev_priv->rx_chan);
-
-	return ret;
+	of_node_put(priv->hbdev.np);
 }
 
 static const struct of_device_id am654_hbmc_dt_ids[] = {
@@ -256,7 +261,7 @@
 
 static struct platform_driver am654_hbmc_platform_driver = {
 	.probe = am654_hbmc_probe,
-	.remove = am654_hbmc_remove,
+	.remove_new = am654_hbmc_remove,
 	.driver = {
 		.name = "hbmc-am654",
 		.of_match_table = am654_hbmc_dt_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/hyperbus/hyperbus-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/hyperbus/hyperbus-core.c
@@ -126,16 +126,12 @@
 }
 EXPORT_SYMBOL_GPL(hyperbus_register_device);
 
-int hyperbus_unregister_device(struct hyperbus_device *hbdev)
+void hyperbus_unregister_device(struct hyperbus_device *hbdev)
 {
-	int ret = 0;
-
 	if (hbdev && hbdev->mtd) {
-		ret = mtd_device_unregister(hbdev->mtd);
+		WARN_ON(mtd_device_unregister(hbdev->mtd));
 		map_destroy(hbdev->mtd);
 	}
-
-	return ret;
 }
 EXPORT_SYMBOL_GPL(hyperbus_unregister_device);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/hyperbus/rpc-if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/hyperbus/rpc-if.c
@@ -124,7 +124,9 @@
 	if (!hyperbus)
 		return -ENOMEM;
 
-	rpcif_sw_init(&hyperbus->rpc, pdev->dev.parent);
+	error = rpcif_sw_init(&hyperbus->rpc, pdev->dev.parent);
+	if (error)
+		return error;
 
 	platform_set_drvdata(pdev, hyperbus);
 
@@ -149,11 +151,12 @@
 static int rpcif_hb_remove(struct platform_device *pdev)
 {
 	struct rpcif_hyperbus *hyperbus = platform_get_drvdata(pdev);
-	int error = hyperbus_unregister_device(&hyperbus->hbdev);
-	struct rpcif *rpc = dev_get_drvdata(pdev->dev.parent);
 
-	rpcif_disable_rpm(rpc);
-	return error;
+	hyperbus_unregister_device(&hyperbus->hbdev);
+
+	rpcif_disable_rpm(&hyperbus->rpc);
+
+	return 0;
 }
 
 static struct platform_driver rpcif_platform_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/lpddr/lpddr2_nvm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/lpddr/lpddr2_nvm.c
@@ -433,6 +433,8 @@
 
 	/* lpddr2_nvm address range */
 	add_range = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!add_range)
+		return -ENODEV;
 
 	/* Populate map_info data structure */
 	*map = (struct map_info) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/maps/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/maps/Kconfig
@@ -302,7 +302,7 @@
 
 config MTD_IXP4XX
 	tristate "CFI Flash device mapped on Intel IXP4xx based systems"
-	depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP4XX
+	depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP4XX && MTD_CFI_ADV_OPTIONS
 	help
 	  This enables MTD access to flash devices on platforms based
 	  on Intel's IXP4xx family of network processors such as the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/maps/physmap-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/maps/physmap-core.c
@@ -528,7 +528,7 @@
 		if (!info->maps[i].phys)
 			info->maps[i].phys = res->start;
 
-		info->win_order = get_bitmask_order(resource_size(res)) - 1;
+		info->win_order = fls64(resource_size(res)) - 1;
 		info->maps[i].size = BIT(info->win_order +
 					 (info->gpios ?
 					  info->gpios->ndescs : 0));
@@ -556,6 +556,17 @@
 		if (info->probe_type) {
 			info->mtds[i] = do_map_probe(info->probe_type,
 						     &info->maps[i]);
+
+			/* Fall back to mapping region as ROM */
+			if (!info->mtds[i] && IS_ENABLED(CONFIG_MTD_ROM) &&
+			    strcmp(info->probe_type, "map_rom")) {
+				dev_warn(&dev->dev,
+					 "map_probe() failed for type %s\n",
+					 info->probe_type);
+
+				info->mtds[i] = do_map_probe("map_rom",
+							     &info->maps[i]);
+			}
 		} else {
 			int j;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/maps/physmap-versatile.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/maps/physmap-versatile.c
@@ -93,6 +93,7 @@
 		return -ENODEV;
 	}
 	ebi_base = of_iomap(ebi, 0);
+	of_node_put(ebi);
 	if (!ebi_base)
 		return -ENODEV;
 
@@ -207,6 +208,7 @@
 
 		versatile_flashprot = (enum versatile_flashprot)devid->data;
 		rmap = syscon_node_to_regmap(sysnp);
+		of_node_put(sysnp);
 		if (IS_ERR(rmap))
 			return PTR_ERR(rmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/maps/pxa2xx-flash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/maps/pxa2xx-flash.c
@@ -66,6 +66,7 @@
 	if (!info->map.virt) {
 		printk(KERN_WARNING "Failed to ioremap %s\n",
 		       info->map.name);
+		kfree(info);
 		return -ENOMEM;
 	}
 	info->map.cached = ioremap_cache(info->map.phys, info->map.size);
@@ -87,6 +88,7 @@
 		iounmap((void *)info->map.virt);
 		if (info->map.cached)
 			iounmap(info->map.cached);
+		kfree(info);
 		return -EIO;
 	}
 	info->mtd->dev.parent = &pdev->dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/mtd_blkdevs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/mtd_blkdevs.c
@@ -457,7 +457,7 @@
 {
 	struct mtd_blktrans_ops *tr;
 
-	if (mtd->type == MTD_ABSENT)
+	if (mtd->type == MTD_ABSENT || mtd->type == MTD_UBIVOLUME)
 		return;
 
 	list_for_each_entry(tr, &blktrans_majors, list)
@@ -497,7 +497,7 @@
 	mutex_lock(&mtd_table_mutex);
 	list_add(&tr->list, &blktrans_majors);
 	mtd_for_each_device(mtd)
-		if (mtd->type != MTD_ABSENT)
+		if (mtd->type != MTD_ABSENT && mtd->type != MTD_UBIVOLUME)
 			tr->add_mtd(tr, mtd);
 	mutex_unlock(&mtd_table_mutex);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/mtdblock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/mtdblock.c
@@ -153,7 +153,7 @@
 				mtdblk->cache_state = STATE_EMPTY;
 				ret = mtd_read(mtd, sect_start, sect_size,
 					       &retlen, mtdblk->cache_data);
-				if (ret)
+				if (ret && !mtd_is_bitflip(ret))
 					return ret;
 				if (retlen != sect_size)
 					return -EIO;
@@ -188,8 +188,12 @@
 	pr_debug("mtdblock: read on \"%s\" at 0x%lx, size 0x%x\n",
 			mtd->name, pos, len);
 
-	if (!sect_size)
-		return mtd_read(mtd, pos, len, &retlen, buf);
+	if (!sect_size) {
+		ret = mtd_read(mtd, pos, len, &retlen, buf);
+		if (ret && !mtd_is_bitflip(ret))
+			return ret;
+		return 0;
+	}
 
 	while (len > 0) {
 		unsigned long sect_start = (pos/sect_size)*sect_size;
@@ -209,7 +213,7 @@
 			memcpy (buf, mtdblk->cache_data + offset, size);
 		} else {
 			ret = mtd_read(mtd, pos, size, &retlen, buf);
-			if (ret)
+			if (ret && !mtd_is_bitflip(ret))
 				return ret;
 			if (retlen != size)
 				return -EIO;
@@ -257,6 +261,10 @@
 		return 0;
 	}
 
+	if (mtd_type_is_nand(mbd->mtd))
+		pr_warn("%s: MTD device '%s' is NAND, please consider using UBI block devices instead.\n",
+			mbd->tr->name, mbd->mtd->name);
+
 	/* OK, it's not open. Create cache info for it */
 	mtdblk->count = 1;
 	mutex_init(&mtdblk->cache_mutex);
@@ -322,10 +330,6 @@
 	if (!(mtd->flags & MTD_WRITEABLE))
 		dev->mbd.readonly = 1;
 
-	if (mtd_type_is_nand(mtd))
-		pr_warn("%s: MTD device '%s' is NAND, please consider using UBI block devices instead.\n",
-			tr->name, mtd->name);
-
 	if (add_mtd_blktrans_dev(&dev->mbd))
 		kfree(dev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/mtdcore.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/mtdcore.c
@@ -546,6 +546,7 @@
 	config.stride = 1;
 	config.read_only = true;
 	config.root_only = true;
+	config.ignore_wp = true;
 	config.no_of_node = !of_device_is_compatible(node, "nvmem-cells");
 	config.priv = mtd;
 
@@ -670,8 +671,10 @@
 	dev_set_drvdata(&mtd->dev, mtd);
 	of_node_get(mtd_get_of_node(mtd));
 	error = device_register(&mtd->dev);
-	if (error)
+	if (error) {
+		put_device(&mtd->dev);
 		goto fail_added;
+	}
 
 	/* Add the nvmem provider */
 	error = mtd_nvmem_add(mtd);
@@ -724,8 +727,6 @@
 
 	mutex_lock(&mtd_table_mutex);
 
-	debugfs_remove_recursive(mtd->dbg.dfs_dir);
-
 	if (idr_find(&mtd_idr, mtd->index) != mtd) {
 		ret = -ENODEV;
 		goto out_error;
@@ -741,6 +742,8 @@
 		       mtd->index, mtd->name, mtd->usecount);
 		ret = -EBUSY;
 	} else {
+		debugfs_remove_recursive(mtd->dbg.dfs_dir);
+
 		/* Try to remove the NVMEM provider */
 		if (mtd->nvmem)
 			nvmem_unregister(mtd->nvmem);
@@ -825,12 +828,12 @@
 
 	/* OTP nvmem will be registered on the physical device */
 	config.dev = mtd->dev.parent;
-	/* just reuse the compatible as name */
 	config.name = compatible;
-	config.id = NVMEM_DEVID_NONE;
+	config.id = NVMEM_DEVID_AUTO;
 	config.owner = THIS_MODULE;
 	config.type = NVMEM_TYPE_OTP;
 	config.root_only = true;
+	config.ignore_wp = true;
 	config.reg_read = reg_read;
 	config.size = size;
 	config.of_node = np;
@@ -876,20 +879,23 @@
 
 static int mtd_otp_nvmem_add(struct mtd_info *mtd)
 {
+	struct device *dev = mtd->dev.parent;
 	struct nvmem_device *nvmem;
 	ssize_t size;
 	int err;
 
 	if (mtd->_get_user_prot_info && mtd->_read_user_prot_reg) {
 		size = mtd_otp_size(mtd, true);
-		if (size < 0)
-			return size;
+		if (size < 0) {
+			err = size;
+			goto err;
+		}
 
 		if (size > 0) {
 			nvmem = mtd_otp_nvmem_register(mtd, "user-otp", size,
 						       mtd_nvmem_user_otp_reg_read);
 			if (IS_ERR(nvmem)) {
-				dev_err(&mtd->dev, "Failed to register OTP NVMEM device\n");
+				dev_err(dev, "Failed to register OTP NVMEM device\n");
 				return PTR_ERR(nvmem);
 			}
 			mtd->otp_user_nvmem = nvmem;
@@ -907,7 +913,7 @@
 			nvmem = mtd_otp_nvmem_register(mtd, "factory-otp", size,
 						       mtd_nvmem_fact_otp_reg_read);
 			if (IS_ERR(nvmem)) {
-				dev_err(&mtd->dev, "Failed to register OTP NVMEM device\n");
+				dev_err(dev, "Failed to register OTP NVMEM device\n");
 				err = PTR_ERR(nvmem);
 				goto err;
 			}
@@ -960,10 +966,14 @@
 
 	mtd_set_dev_defaults(mtd);
 
+	ret = mtd_otp_nvmem_add(mtd);
+	if (ret)
+		goto out;
+
 	if (IS_ENABLED(CONFIG_MTD_PARTITIONED_MASTER)) {
 		ret = add_mtd_device(mtd);
 		if (ret)
-			return ret;
+			goto out;
 	}
 
 	/* Prefer parsed partitions over driver-provided fallback */
@@ -998,9 +1008,12 @@
 		register_reboot_notifier(&mtd->reboot_notifier);
 	}
 
-	ret = mtd_otp_nvmem_add(mtd);
-
 out:
+	if (ret) {
+		nvmem_unregister(mtd->otp_user_nvmem);
+		nvmem_unregister(mtd->otp_factory_nvmem);
+	}
+
 	if (ret && device_is_registered(&mtd->dev))
 		del_mtd_device(mtd);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/mtdpart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/mtdpart.c
@@ -312,7 +312,7 @@
 	if (err)
 		return err;
 
-	list_del(&child->part.node);
+	list_del(&mtd->part.node);
 	free_partition(mtd);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/onenand/generic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/onenand/generic.c
@@ -53,7 +53,12 @@
 	}
 
 	info->onenand.mmcontrol = pdata ? pdata->mmcontrol : NULL;
-	info->onenand.irq = platform_get_irq(pdev, 0);
+
+	err = platform_get_irq(pdev, 0);
+	if (err < 0)
+		goto out_iounmap;
+
+	info->onenand.irq = err;
 
 	info->mtd.dev.parent = &pdev->dev;
 	info->mtd.priv = &info->onenand;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/onenand/onenand_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/onenand/onenand_base.c
@@ -2911,6 +2911,7 @@
 	ret = ONENAND_IS_4KB_PAGE(this) ?
 		onenand_mlc_read_ops_nolock(mtd, from, &ops) :
 		onenand_read_ops_nolock(mtd, from, &ops);
+	*retlen = ops.retlen;
 
 	/* Exit OTP access mode */
 	this->command(mtd, ONENAND_CMD_RESET, 0, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/Kconfig
@@ -254,8 +254,7 @@
 	tristate "Freescale IFC NAND controller"
 	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST
 	depends on HAS_IOMEM
-	select FSL_IFC
-	select MEMORY
+	depends on FSL_IFC
 	help
 	  Various Freescale chips e.g P1010, include a NAND Flash machine
 	  with built-in hardware ECC capabilities.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/ams-delta.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/ams-delta.c
@@ -217,9 +217,8 @@
 
 static int gpio_nand_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -370,6 +369,13 @@
 	/* Release write protection */
 	gpiod_set_value(priv->gpiod_nwp, 0);
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	this->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	/* Scan to find existence of the device */
 	err = nand_scan(this, 1);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -347,17 +347,17 @@
 
 	/* Update clock frequency */
 	if (nfc->cur_clk != anand->clk) {
-		clk_disable_unprepare(nfc->controller_clk);
-		ret = clk_set_rate(nfc->controller_clk, anand->clk);
+		clk_disable_unprepare(nfc->bus_clk);
+		ret = clk_set_rate(nfc->bus_clk, anand->clk);
 		if (ret) {
 			dev_err(nfc->dev, "Failed to change clock rate\n");
 			return ret;
 		}
 
-		ret = clk_prepare_enable(nfc->controller_clk);
+		ret = clk_prepare_enable(nfc->bus_clk);
 		if (ret) {
 			dev_err(nfc->dev,
-				"Failed to re-enable the controller clock\n");
+				"Failed to re-enable the bus clock\n");
 			return ret;
 		}
 
@@ -515,6 +515,7 @@
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
 	dma_addr_t dma_addr;
+	u8 status;
 	int ret;
 	struct anfc_op nfc_op = {
 		.pkt_reg =
@@ -561,10 +562,21 @@
 	}
 
 	/* Spare data is not protected */
-	if (oob_required)
+	if (oob_required) {
 		ret = nand_write_oob_std(chip, page);
+		if (ret)
+			return ret;
+	}
 
-	return ret;
+	/* Check write status on the chip side */
+	ret = nand_status_op(chip, &status);
+	if (ret)
+		return ret;
+
+	if (status & NAND_STATUS_FAIL)
+		return -EIO;
+
+	return 0;
 }
 
 static int anfc_sel_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
@@ -973,6 +985,21 @@
 		nvddr = nand_get_nvddr_timings(conf);
 		if (IS_ERR(nvddr))
 			return PTR_ERR(nvddr);
+
+		/*
+		 * The controller only supports data payload requests which are
+		 * a multiple of 4. In practice, most data accesses are 4-byte
+		 * aligned and this is not an issue. However, rounding up will
+		 * simply be refused by the controller if we reached the end of
+		 * the device *and* we are using the NV-DDR interface(!). In
+		 * this situation, unaligned data requests ending at the device
+		 * boundary will confuse the controller and cannot be performed.
+		 *
+		 * This is something that happens in nand_read_subpage() when
+		 * selecting software ECC support and must be avoided.
+		 */
+		if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT)
+			return -ENOTSUPP;
 	} else {
 		sdr = nand_get_sdr_timings(conf);
 		if (IS_ERR(sdr))
@@ -1028,7 +1055,13 @@
 				 DQS_BUFF_SEL_OUT(dqs_mode);
 	}
 
-	anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
+	if (nand_interface_is_sdr(conf)) {
+		anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
+	} else {
+		/* ONFI timings are defined in picoseconds */
+		anand->clk = div_u64((u64)NSEC_PER_SEC * 1000,
+				     conf->timings.nvddr.tCK_min);
+	}
 
 	/*
 	 * Due to a hardware bug in the ZynqMP SoC, SDR timing modes 0-1 work
@@ -1392,8 +1425,8 @@
 	 * case, the "not" chosen CS is assigned to nfc->spare_cs and selected
 	 * whenever a GPIO CS must be asserted.
 	 */
-	if (nfc->cs_array && nfc->ncs > 2) {
-		if (!nfc->cs_array[0] && !nfc->cs_array[1]) {
+	if (nfc->cs_array) {
+		if (nfc->ncs > 2 && !nfc->cs_array[0] && !nfc->cs_array[1]) {
 			dev_err(nfc->dev,
 				"Assign a single native CS when using GPIOs\n");
 			return -EINVAL;
@@ -1477,8 +1510,15 @@
 
 static int anfc_remove(struct platform_device *pdev)
 {
+	int i;
 	struct arasan_nfc *nfc = platform_get_drvdata(pdev);
 
+	for (i = 0; i < nfc->ncs; i++) {
+		if (nfc->cs_array[i]) {
+			gpiod_put(nfc->cs_array[i]);
+		}
+	}
+
 	anfc_chips_cleanup(nfc);
 
 	clk_disable_unprepare(nfc->bus_clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/atmel/nand-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/atmel/nand-controller.c
@@ -405,6 +405,7 @@
 
 	dma_async_issue_pending(nc->dmac);
 	wait_for_completion(&finished);
+	dma_unmap_single(nc->dev, buf_dma, len, dir);
 
 	return 0;
 
@@ -2060,13 +2061,15 @@
 	nc->mck = of_clk_get(dev->parent->of_node, 0);
 	if (IS_ERR(nc->mck)) {
 		dev_err(dev, "Failed to retrieve MCK clk\n");
-		return PTR_ERR(nc->mck);
+		ret = PTR_ERR(nc->mck);
+		goto out_release_dma;
 	}
 
 	np = of_parse_phandle(dev->parent->of_node, "atmel,smc", 0);
 	if (!np) {
 		dev_err(dev, "Missing or invalid atmel,smc property\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto out_release_dma;
 	}
 
 	nc->smc = syscon_node_to_regmap(np);
@@ -2074,10 +2077,16 @@
 	if (IS_ERR(nc->smc)) {
 		ret = PTR_ERR(nc->smc);
 		dev_err(dev, "Could not get SMC regmap (err = %d)\n", ret);
-		return ret;
+		goto out_release_dma;
 	}
 
 	return 0;
+
+out_release_dma:
+	if (nc->dmac)
+		dma_release_channel(nc->dmac);
+
+	return ret;
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/atmel/pmecc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/atmel/pmecc.c
@@ -362,7 +362,7 @@
 	size = ALIGN(size, sizeof(s32));
 	size += (req->ecc.strength + 1) * sizeof(s32) * 3;
 
-	user = kzalloc(size, GFP_KERNEL);
+	user = devm_kzalloc(pmecc->dev, size, GFP_KERNEL);
 	if (!user)
 		return ERR_PTR(-ENOMEM);
 
@@ -380,10 +380,8 @@
 	user->delta = user->dmu + req->ecc.strength + 1;
 
 	gf_tables = atmel_pmecc_get_gf_tables(req);
-	if (IS_ERR(gf_tables)) {
-		kfree(user);
+	if (IS_ERR(gf_tables))
 		return ERR_CAST(gf_tables);
-	}
 
 	user->gf_tables = gf_tables;
 
@@ -408,12 +406,6 @@
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_create_user);
 
-void atmel_pmecc_destroy_user(struct atmel_pmecc_user *user)
-{
-	kfree(user);
-}
-EXPORT_SYMBOL_GPL(atmel_pmecc_destroy_user);
-
 static int get_strength(struct atmel_pmecc_user *user)
 {
 	const int *strengths = user->pmecc->caps->strengths;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/atmel/pmecc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/atmel/pmecc.h
@@ -55,8 +55,6 @@
 struct atmel_pmecc_user *
 atmel_pmecc_create_user(struct atmel_pmecc *pmecc,
 			struct atmel_pmecc_user_req *req);
-void atmel_pmecc_destroy_user(struct atmel_pmecc_user *user);
-
 void atmel_pmecc_reset(struct atmel_pmecc *pmecc);
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op);
 void atmel_pmecc_disable(struct atmel_pmecc_user *user);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/au1550nd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/au1550nd.c
@@ -239,9 +239,8 @@
 
 static int au1550nd_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -310,6 +309,13 @@
 	if (pd->devwidth)
 		this->options |= NAND_BUSWIDTH_16;
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	this->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	ret = nand_scan(this, 1);
 	if (ret) {
 		dev_err(&pdev->dev, "NAND scan failed with %d\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/brcmnand/brcmnand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/brcmnand/brcmnand.c
@@ -25,6 +25,7 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/slab.h>
+#include <linux/static_key.h>
 #include <linux/list.h>
 #include <linux/log2.h>
 
@@ -207,6 +208,8 @@
 
 struct brcmnand_host;
 
+static DEFINE_STATIC_KEY_FALSE(brcmnand_soc_has_ops_key);
+
 struct brcmnand_controller {
 	struct device		*dev;
 	struct nand_controller	controller;
@@ -268,6 +271,7 @@
 	const unsigned int	*page_sizes;
 	unsigned int		page_size_shift;
 	unsigned int		max_oob;
+	u32			ecc_level_shift;
 	u32			features;
 
 	/* for low-power standby/resume only */
@@ -592,15 +596,53 @@
 	INTFC_CTLR_READY		= BIT(31),
 };
 
+/***********************************************************************
+ * NAND ACC CONTROL bitfield
+ *
+ * Some bits have remained constant throughout hardware revision, while
+ * others have shifted around.
+ ***********************************************************************/
+
+/* Constant for all versions (where supported) */
+enum {
+	/* See BRCMNAND_HAS_CACHE_MODE */
+	ACC_CONTROL_CACHE_MODE				= BIT(22),
+
+	/* See BRCMNAND_HAS_PREFETCH */
+	ACC_CONTROL_PREFETCH				= BIT(23),
+
+	ACC_CONTROL_PAGE_HIT				= BIT(24),
+	ACC_CONTROL_WR_PREEMPT				= BIT(25),
+	ACC_CONTROL_PARTIAL_PAGE			= BIT(26),
+	ACC_CONTROL_RD_ERASED				= BIT(27),
+	ACC_CONTROL_FAST_PGM_RDIN			= BIT(28),
+	ACC_CONTROL_WR_ECC				= BIT(30),
+	ACC_CONTROL_RD_ECC				= BIT(31),
+};
+
+#define	ACC_CONTROL_ECC_SHIFT			16
+/* Only for v7.2 */
+#define	ACC_CONTROL_ECC_EXT_SHIFT		13
+
+static inline bool brcmnand_non_mmio_ops(struct brcmnand_controller *ctrl)
+{
+	return static_branch_unlikely(&brcmnand_soc_has_ops_key);
+}
+
 static inline u32 nand_readreg(struct brcmnand_controller *ctrl, u32 offs)
 {
+	if (brcmnand_non_mmio_ops(ctrl))
+		return brcmnand_soc_read(ctrl->soc, offs);
 	return brcmnand_readl(ctrl->nand_base + offs);
 }
 
 static inline void nand_writereg(struct brcmnand_controller *ctrl, u32 offs,
 				 u32 val)
 {
-	brcmnand_writel(val, ctrl->nand_base + offs);
+	if (brcmnand_non_mmio_ops(ctrl))
+		brcmnand_soc_write(ctrl->soc, val, offs);
+	else
+		brcmnand_writel(val, ctrl->nand_base + offs);
 }
 
 static int brcmnand_revision_init(struct brcmnand_controller *ctrl)
@@ -719,6 +761,12 @@
 	else if (of_property_read_bool(ctrl->dev->of_node, "brcm,nand-has-wp"))
 		ctrl->features |= BRCMNAND_HAS_WP;
 
+	/* v7.2 has different ecc level shift in the acc register */
+	if (ctrl->nand_version == 0x0702)
+		ctrl->ecc_level_shift = ACC_CONTROL_ECC_EXT_SHIFT;
+	else
+		ctrl->ecc_level_shift = ACC_CONTROL_ECC_SHIFT;
+
 	return 0;
 }
 
@@ -766,13 +814,18 @@
 
 static inline u32 brcmnand_read_fc(struct brcmnand_controller *ctrl, int word)
 {
+	if (brcmnand_non_mmio_ops(ctrl))
+		return brcmnand_soc_read(ctrl->soc, BRCMNAND_NON_MMIO_FC_ADDR);
 	return __raw_readl(ctrl->nand_fc + word * 4);
 }
 
 static inline void brcmnand_write_fc(struct brcmnand_controller *ctrl,
 				     int word, u32 val)
 {
-	__raw_writel(val, ctrl->nand_fc + word * 4);
+	if (brcmnand_non_mmio_ops(ctrl))
+		brcmnand_soc_write(ctrl->soc, val, BRCMNAND_NON_MMIO_FC_ADDR);
+	else
+		__raw_writel(val, ctrl->nand_fc + word * 4);
 }
 
 static inline void edu_writel(struct brcmnand_controller *ctrl,
@@ -902,30 +955,6 @@
 	return 0;
 }
 
-/***********************************************************************
- * NAND ACC CONTROL bitfield
- *
- * Some bits have remained constant throughout hardware revision, while
- * others have shifted around.
- ***********************************************************************/
-
-/* Constant for all versions (where supported) */
-enum {
-	/* See BRCMNAND_HAS_CACHE_MODE */
-	ACC_CONTROL_CACHE_MODE				= BIT(22),
-
-	/* See BRCMNAND_HAS_PREFETCH */
-	ACC_CONTROL_PREFETCH				= BIT(23),
-
-	ACC_CONTROL_PAGE_HIT				= BIT(24),
-	ACC_CONTROL_WR_PREEMPT				= BIT(25),
-	ACC_CONTROL_PARTIAL_PAGE			= BIT(26),
-	ACC_CONTROL_RD_ERASED				= BIT(27),
-	ACC_CONTROL_FAST_PGM_RDIN			= BIT(28),
-	ACC_CONTROL_WR_ECC				= BIT(30),
-	ACC_CONTROL_RD_ECC				= BIT(31),
-};
-
 static inline u32 brcmnand_spare_area_mask(struct brcmnand_controller *ctrl)
 {
 	if (ctrl->nand_version == 0x0702)
@@ -938,18 +967,15 @@
 		return GENMASK(4, 0);
 }
 
-#define NAND_ACC_CONTROL_ECC_SHIFT	16
-#define NAND_ACC_CONTROL_ECC_EXT_SHIFT	13
-
 static inline u32 brcmnand_ecc_level_mask(struct brcmnand_controller *ctrl)
 {
 	u32 mask = (ctrl->nand_version >= 0x0600) ? 0x1f : 0x0f;
 
-	mask <<= NAND_ACC_CONTROL_ECC_SHIFT;
+	mask <<= ACC_CONTROL_ECC_SHIFT;
 
 	/* v7.2 includes additional ECC levels */
-	if (ctrl->nand_version >= 0x0702)
-		mask |= 0x7 << NAND_ACC_CONTROL_ECC_EXT_SHIFT;
+	if (ctrl->nand_version == 0x0702)
+		mask |= 0x7 << ACC_CONTROL_ECC_EXT_SHIFT;
 
 	return mask;
 }
@@ -963,8 +989,8 @@
 
 	if (en) {
 		acc_control |= ecc_flags; /* enable RD/WR ECC */
-		acc_control |= host->hwcfg.ecc_level
-			       << NAND_ACC_CONTROL_ECC_SHIFT;
+		acc_control &= ~brcmnand_ecc_level_mask(ctrl);
+		acc_control |= host->hwcfg.ecc_level << ctrl->ecc_level_shift;
 	} else {
 		acc_control &= ~ecc_flags; /* disable RD/WR ECC */
 		acc_control &= ~brcmnand_ecc_level_mask(ctrl);
@@ -1043,6 +1069,14 @@
 		cpu_relax();
 	} while (time_after(limit, jiffies));
 
+	/*
+	 * do a final check after time out in case the CPU was busy and the driver
+	 * did not get enough time to perform the polling to avoid false alarms
+	 */
+	val = brcmnand_read_reg(ctrl, BRCMNAND_INTFC_STATUS);
+	if ((val & mask) == expected_val)
+		return 0;
+
 	dev_warn(ctrl->dev, "timeout on status poll (expected %x got %x)\n",
 		 expected_val, val & mask);
 
@@ -1432,19 +1466,33 @@
 			     const u8 *oob, int sas, int sector_1k)
 {
 	int tbytes = sas << sector_1k;
-	int j;
+	int j, k = 0;
+	u32 last = 0xffffffff;
+	u8 *plast = (u8 *)&last;
 
 	/* Adjust OOB values for 1K sector size */
 	if (sector_1k && (i & 0x01))
 		tbytes = max(0, tbytes - (int)ctrl->max_oob);
 	tbytes = min_t(int, tbytes, ctrl->max_oob);
 
-	for (j = 0; j < tbytes; j += 4)
+	/*
+	 * tbytes may not be multiple of words. Make sure we don't read out of
+	 * the boundary and stop at last word.
+	 */
+	for (j = 0; (j + 3) < tbytes; j += 4)
 		oob_reg_write(ctrl, j,
 				(oob[j + 0] << 24) |
 				(oob[j + 1] << 16) |
 				(oob[j + 2] <<  8) |
 				(oob[j + 3] <<  0));
+
+	/* handle the remaing bytes */
+	while (j < tbytes)
+		plast[k++] = oob[j++];
+
+	if (tbytes & 0x3)
+		oob_reg_write(ctrl, (tbytes & ~0x3), (__force u32)cpu_to_be32(last));
+
 	return tbytes;
 }
 
@@ -1563,7 +1611,17 @@
 
 	dev_dbg(ctrl->dev, "send native cmd %d addr 0x%llx\n", cmd, cmd_addr);
 
-	BUG_ON(ctrl->cmd_pending != 0);
+	/*
+	 * If we came here through _panic_write and there is a pending
+	 * command, try to wait for it. If it times out, rather than
+	 * hitting BUG_ON, just return so we don't crash while crashing.
+	 */
+	if (oops_in_progress) {
+		if (ctrl->cmd_pending &&
+			bcmnand_ctrl_poll_status(ctrl, NAND_CTRL_RDY, NAND_CTRL_RDY, 0))
+			return;
+	} else
+		BUG_ON(ctrl->cmd_pending != 0);
 	ctrl->cmd_pending = cmd;
 
 	ret = bcmnand_ctrl_poll_status(ctrl, NAND_CTRL_RDY, NAND_CTRL_RDY, 0);
@@ -2106,7 +2164,7 @@
 					mtd->oobsize / trans,
 					host->hwcfg.sector_size_1k);
 
-		if (!ret) {
+		if (ret != -EBADMSG) {
 			*err_addr = brcmnand_get_uncorrecc_addr(ctrl);
 
 			if (*err_addr)
@@ -2532,7 +2590,7 @@
 	tmp &= ~brcmnand_ecc_level_mask(ctrl);
 	tmp &= ~brcmnand_spare_area_mask(ctrl);
 	if (ctrl->nand_version >= 0x0302) {
-		tmp |= cfg->ecc_level << NAND_ACC_CONTROL_ECC_SHIFT;
+		tmp |= cfg->ecc_level << ctrl->ecc_level_shift;
 		tmp |= cfg->spare_area_size;
 	}
 	nand_writereg(ctrl, acc_control_offs, tmp);
@@ -2583,6 +2641,8 @@
 	struct nand_chip *chip = &host->chip;
 	const struct nand_ecc_props *requirements =
 		nanddev_get_ecc_requirements(&chip->base);
+	struct nand_memory_organization *memorg =
+		nanddev_get_memorg(&chip->base);
 	struct brcmnand_controller *ctrl = host->ctrl;
 	struct brcmnand_cfg *cfg = &host->hwcfg;
 	char msg[128];
@@ -2604,10 +2664,11 @@
 	if (cfg->spare_area_size > ctrl->max_oob)
 		cfg->spare_area_size = ctrl->max_oob;
 	/*
-	 * Set oobsize to be consistent with controller's spare_area_size, as
-	 * the rest is inaccessible.
+	 * Set mtd and memorg oobsize to be consistent with controller's
+	 * spare_area_size, as the rest is inaccessible.
 	 */
 	mtd->oobsize = cfg->spare_area_size * (mtd->writesize >> FC_SHIFT);
+	memorg->oobsize = mtd->oobsize;
 
 	cfg->device_size = mtd->size;
 	cfg->block_size = mtd->erasesize;
@@ -2999,6 +3060,12 @@
 	dev_set_drvdata(dev, ctrl);
 	ctrl->dev = dev;
 
+	/* Enable the static key if the soc provides I/O operations indicating
+	 * that a non-memory mapped IO access path must be used
+	 */
+	if (brcmnand_soc_has_ops(ctrl->soc))
+		static_branch_enable(&brcmnand_soc_has_ops_key);
+
 	init_completion(&ctrl->done);
 	init_completion(&ctrl->dma_done);
 	init_completion(&ctrl->edu_done);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/brcmnand/brcmnand.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/brcmnand/brcmnand.h
@@ -11,12 +11,25 @@
 
 struct platform_device;
 struct dev_pm_ops;
+struct brcmnand_io_ops;
+
+/* Special register offset constant to intercept a non-MMIO access
+ * to the flash cache register space. This is intentionally large
+ * not to overlap with an existing offset.
+ */
+#define BRCMNAND_NON_MMIO_FC_ADDR	0xffffffff
 
 struct brcmnand_soc {
 	bool (*ctlrdy_ack)(struct brcmnand_soc *soc);
 	void (*ctlrdy_set_enabled)(struct brcmnand_soc *soc, bool en);
 	void (*prepare_data_bus)(struct brcmnand_soc *soc, bool prepare,
 				 bool is_param);
+	const struct brcmnand_io_ops *ops;
+};
+
+struct brcmnand_io_ops {
+	u32 (*read_reg)(struct brcmnand_soc *soc, u32 offset);
+	void (*write_reg)(struct brcmnand_soc *soc, u32 val, u32 offset);
 };
 
 static inline void brcmnand_soc_data_bus_prepare(struct brcmnand_soc *soc,
@@ -58,6 +71,22 @@
 		writel_relaxed(val, addr);
 }
 
+static inline bool brcmnand_soc_has_ops(struct brcmnand_soc *soc)
+{
+	return soc && soc->ops && soc->ops->read_reg && soc->ops->write_reg;
+}
+
+static inline u32 brcmnand_soc_read(struct brcmnand_soc *soc, u32 offset)
+{
+	return soc->ops->read_reg(soc, offset);
+}
+
+static inline void brcmnand_soc_write(struct brcmnand_soc *soc, u32 val,
+				      u32 offset)
+{
+	soc->ops->write_reg(soc, val, offset);
+}
+
 int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc);
 int brcmnand_remove(struct platform_device *pdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/cadence-nand-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/cadence-nand-controller.c
@@ -469,6 +469,8 @@
 	struct {
 		void __iomem *virt;
 		dma_addr_t dma;
+		dma_addr_t iova_dma;
+		u32 size;
 	} io;
 
 	int irq;
@@ -1830,11 +1832,11 @@
 	}
 
 	if (dir == DMA_FROM_DEVICE) {
-		src_dma = cdns_ctrl->io.dma;
+		src_dma = cdns_ctrl->io.iova_dma;
 		dst_dma = buf_dma;
 	} else {
 		src_dma = buf_dma;
-		dst_dma = cdns_ctrl->io.dma;
+		dst_dma = cdns_ctrl->io.iova_dma;
 	}
 
 	tx = dmaengine_prep_dma_memcpy(cdns_ctrl->dmac, dst_dma, src_dma, len,
@@ -1856,12 +1858,12 @@
 	dma_async_issue_pending(cdns_ctrl->dmac);
 	wait_for_completion(&finished);
 
-	dma_unmap_single(cdns_ctrl->dev, buf_dma, len, dir);
+	dma_unmap_single(dma_dev->dev, buf_dma, len, dir);
 
 	return 0;
 
 err_unmap:
-	dma_unmap_single(cdns_ctrl->dev, buf_dma, len, dir);
+	dma_unmap_single(dma_dev->dev, buf_dma, len, dir);
 
 err:
 	dev_dbg(cdns_ctrl->dev, "Fall back to CPU I/O\n");
@@ -2831,6 +2833,7 @@
 static int cadence_nand_init(struct cdns_nand_ctrl *cdns_ctrl)
 {
 	dma_cap_mask_t mask;
+	struct dma_device *dma_dev = cdns_ctrl->dmac->device;
 	int ret;
 
 	cdns_ctrl->cdma_desc = dma_alloc_coherent(cdns_ctrl->dev,
@@ -2866,15 +2869,24 @@
 	dma_cap_set(DMA_MEMCPY, mask);
 
 	if (cdns_ctrl->caps1->has_dma) {
-		cdns_ctrl->dmac = dma_request_channel(mask, NULL, NULL);
-		if (!cdns_ctrl->dmac) {
-			dev_err(cdns_ctrl->dev,
-				"Unable to get a DMA channel\n");
-			ret = -EBUSY;
+		cdns_ctrl->dmac = dma_request_chan_by_mask(&mask);
+		if (IS_ERR(cdns_ctrl->dmac)) {
+			ret = dev_err_probe(cdns_ctrl->dev, PTR_ERR(cdns_ctrl->dmac),
+					    "%d: Failed to get a DMA channel\n", ret);
 			goto disable_irq;
 		}
 	}
 
+	cdns_ctrl->io.iova_dma = dma_map_resource(dma_dev->dev, cdns_ctrl->io.dma,
+						  cdns_ctrl->io.size,
+						  DMA_BIDIRECTIONAL, 0);
+
+	ret = dma_mapping_error(dma_dev->dev, cdns_ctrl->io.iova_dma);
+	if (ret) {
+		dev_err(cdns_ctrl->dev, "Failed to map I/O resource to DMA\n");
+		goto dma_release_chnl;
+	}
+
 	nand_controller_init(&cdns_ctrl->controller);
 	INIT_LIST_HEAD(&cdns_ctrl->chips);
 
@@ -2885,18 +2897,22 @@
 	if (ret) {
 		dev_err(cdns_ctrl->dev, "Failed to register MTD: %d\n",
 			ret);
-		goto dma_release_chnl;
+		goto unmap_dma_resource;
 	}
 
 	kfree(cdns_ctrl->buf);
 	cdns_ctrl->buf = kzalloc(cdns_ctrl->buf_size, GFP_KERNEL);
 	if (!cdns_ctrl->buf) {
 		ret = -ENOMEM;
-		goto dma_release_chnl;
+		goto unmap_dma_resource;
 	}
 
 	return 0;
 
+unmap_dma_resource:
+	dma_unmap_resource(dma_dev->dev, cdns_ctrl->io.iova_dma,
+			   cdns_ctrl->io.size, DMA_BIDIRECTIONAL, 0);
+
 dma_release_chnl:
 	if (cdns_ctrl->dmac)
 		dma_release_channel(cdns_ctrl->dmac);
@@ -2918,6 +2934,10 @@
 static void cadence_nand_remove(struct cdns_nand_ctrl *cdns_ctrl)
 {
 	cadence_nand_chips_cleanup(cdns_ctrl);
+	if (cdns_ctrl->dmac)
+		dma_unmap_resource(cdns_ctrl->dmac->device->dev,
+				   cdns_ctrl->io.iova_dma, cdns_ctrl->io.size,
+				   DMA_BIDIRECTIONAL, 0);
 	cadence_nand_irq_cleanup(cdns_ctrl->irq, cdns_ctrl);
 	kfree(cdns_ctrl->buf);
 	dma_free_coherent(cdns_ctrl->dev, sizeof(struct cadence_nand_cdma_desc),
@@ -2983,12 +3003,13 @@
 	if (IS_ERR(cdns_ctrl->reg))
 		return PTR_ERR(cdns_ctrl->reg);
 
-	res = platform_get_resource(ofdev, IORESOURCE_MEM, 1);
-	cdns_ctrl->io.dma = res->start;
-	cdns_ctrl->io.virt = devm_ioremap_resource(&ofdev->dev, res);
+	cdns_ctrl->io.virt = devm_platform_get_and_ioremap_resource(ofdev, 1, &res);
 	if (IS_ERR(cdns_ctrl->io.virt))
 		return PTR_ERR(cdns_ctrl->io.virt);
 
+	cdns_ctrl->io.dma = res->start;
+	cdns_ctrl->io.size = resource_size(res);
+
 	dt->clk = devm_clk_get(cdns_ctrl->dev, "nf_clk");
 	if (IS_ERR(dt->clk))
 		return PTR_ERR(dt->clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/davinci_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/davinci_nand.c
@@ -371,77 +371,6 @@
 	return corrected;
 }
 
-/**
- * nand_read_page_hwecc_oob_first - hw ecc, read oob first
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @oob_required: caller requires OOB data read to chip->oob_poi
- * @page: page number to read
- *
- * Hardware ECC for large page chips, require OOB to be read first. For this
- * ECC mode, the write_page method is re-used from ECC_HW. These methods
- * read/write ECC from the OOB area, unlike the ECC_HW_SYNDROME support with
- * multiple ECC steps, follows the "infix ECC" scheme and reads/writes ECC from
- * the data area, by overwriting the NAND manufacturer bad block markings.
- */
-static int nand_davinci_read_page_hwecc_oob_first(struct nand_chip *chip,
-						  uint8_t *buf,
-						  int oob_required, int page)
-{
-	struct mtd_info *mtd = nand_to_mtd(chip);
-	int i, eccsize = chip->ecc.size, ret;
-	int eccbytes = chip->ecc.bytes;
-	int eccsteps = chip->ecc.steps;
-	uint8_t *p = buf;
-	uint8_t *ecc_code = chip->ecc.code_buf;
-	uint8_t *ecc_calc = chip->ecc.calc_buf;
-	unsigned int max_bitflips = 0;
-
-	/* Read the OOB area first */
-	ret = nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize);
-	if (ret)
-		return ret;
-
-	ret = nand_read_page_op(chip, page, 0, NULL, 0);
-	if (ret)
-		return ret;
-
-	ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0,
-					 chip->ecc.total);
-	if (ret)
-		return ret;
-
-	for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
-		int stat;
-
-		chip->ecc.hwctl(chip, NAND_ECC_READ);
-
-		ret = nand_read_data_op(chip, p, eccsize, false, false);
-		if (ret)
-			return ret;
-
-		chip->ecc.calculate(chip, p, &ecc_calc[i]);
-
-		stat = chip->ecc.correct(chip, p, &ecc_code[i], NULL);
-		if (stat == -EBADMSG &&
-		    (chip->ecc.options & NAND_ECC_GENERIC_ERASED_CHECK)) {
-			/* check for empty pages with bitflips */
-			stat = nand_check_erased_ecc_chunk(p, eccsize,
-							   &ecc_code[i],
-							   eccbytes, NULL, 0,
-							   chip->ecc.strength);
-		}
-
-		if (stat < 0) {
-			mtd->ecc_stats.failed++;
-		} else {
-			mtd->ecc_stats.corrected += stat;
-			max_bitflips = max_t(unsigned int, max_bitflips, stat);
-		}
-	}
-	return max_bitflips;
-}
-
 /*----------------------------------------------------------------------*/
 
 /* An ECC layout for using 4-bit ECC with small-page flash, storing
@@ -651,7 +580,7 @@
 			} else if (chunks == 4 || chunks == 8) {
 				mtd_set_ooblayout(mtd,
 						  nand_get_large_page_ooblayout());
-				chip->ecc.read_page = nand_davinci_read_page_hwecc_oob_first;
+				chip->ecc.read_page = nand_read_page_hwecc_oob_first;
 			} else {
 				return -EIO;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/denali_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/denali_pci.c
@@ -74,22 +74,21 @@
 		return ret;
 	}
 
-	denali->reg = ioremap(csr_base, csr_len);
+	denali->reg = devm_ioremap(denali->dev, csr_base, csr_len);
 	if (!denali->reg) {
 		dev_err(&dev->dev, "Spectra: Unable to remap memory region\n");
 		return -ENOMEM;
 	}
 
-	denali->host = ioremap(mem_base, mem_len);
+	denali->host = devm_ioremap(denali->dev, mem_base, mem_len);
 	if (!denali->host) {
 		dev_err(&dev->dev, "Spectra: ioremap failed!");
-		ret = -ENOMEM;
-		goto out_unmap_reg;
+		return -ENOMEM;
 	}
 
 	ret = denali_init(denali);
 	if (ret)
-		goto out_unmap_host;
+		return ret;
 
 	nsels = denali->nbanks;
 
@@ -117,10 +116,6 @@
 
 out_remove_denali:
 	denali_remove(denali);
-out_unmap_host:
-	iounmap(denali->host);
-out_unmap_reg:
-	iounmap(denali->reg);
 	return ret;
 }
 
@@ -129,8 +124,6 @@
 	struct denali_controller *denali = pci_get_drvdata(dev);
 
 	denali_remove(denali);
-	iounmap(denali->reg);
-	iounmap(denali->host);
 }
 
 static struct pci_driver denali_pci_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/diskonchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/diskonchip.c
@@ -53,7 +53,7 @@
 	0xe8000, 0xea000, 0xec000, 0xee000,
 #endif
 #endif
-	0xffffffff };
+};
 
 static struct mtd_info *doclist = NULL;
 
@@ -1098,7 +1098,7 @@
 		    (i == 0) && (ip->firstUnit > 0)) {
 			parts[0].name = " DiskOnChip IPL / Media Header partition";
 			parts[0].offset = 0;
-			parts[0].size = mtd->erasesize * ip->firstUnit;
+			parts[0].size = (uint64_t)mtd->erasesize * ip->firstUnit;
 			numparts = 1;
 		}
 
@@ -1552,7 +1552,7 @@
 		if (ret < 0)
 			return ret;
 	} else {
-		for (i = 0; (doc_locations[i] != 0xffffffff); i++) {
+		for (i = 0; i < ARRAY_SIZE(doc_locations); i++) {
 			doc_probe(doc_locations[i]);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/fsl_elbc_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/fsl_elbc_nand.c
@@ -726,36 +726,40 @@
 	struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
 	unsigned int al;
 
-	switch (chip->ecc.engine_type) {
 	/*
 	 * if ECC was not chosen in DT, decide whether to use HW or SW ECC from
 	 * CS Base Register
 	 */
-	case NAND_ECC_ENGINE_TYPE_NONE:
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_INVALID) {
 		/* If CS Base Register selects full hardware ECC then use it */
 		if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) ==
 		    BR_DECC_CHK_GEN) {
-			chip->ecc.read_page = fsl_elbc_read_page;
-			chip->ecc.write_page = fsl_elbc_write_page;
-			chip->ecc.write_subpage = fsl_elbc_write_subpage;
-
 			chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_ON_HOST;
-			mtd_set_ooblayout(mtd, &fsl_elbc_ooblayout_ops);
-			chip->ecc.size = 512;
-			chip->ecc.bytes = 3;
-			chip->ecc.strength = 1;
 		} else {
 			/* otherwise fall back to default software ECC */
 			chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
 			chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 		}
+	}
+
+	switch (chip->ecc.engine_type) {
+	/* if HW ECC was chosen, setup ecc and oob layout */
+	case NAND_ECC_ENGINE_TYPE_ON_HOST:
+		chip->ecc.read_page = fsl_elbc_read_page;
+		chip->ecc.write_page = fsl_elbc_write_page;
+		chip->ecc.write_subpage = fsl_elbc_write_subpage;
+		mtd_set_ooblayout(mtd, &fsl_elbc_ooblayout_ops);
+		chip->ecc.size = 512;
+		chip->ecc.bytes = 3;
+		chip->ecc.strength = 1;
 		break;
 
-	/* if SW ECC was chosen in DT, we do not need to set anything here */
+	/* if none or SW ECC was chosen, we do not need to set anything here */
+	case NAND_ECC_ENGINE_TYPE_NONE:
 	case NAND_ECC_ENGINE_TYPE_SOFT:
+	case NAND_ECC_ENGINE_TYPE_ON_DIE:
 		break;
 
-	/* should we also implement *_ECC_ENGINE_CONTROLLER to do as above? */
 	default:
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/fsl_ifc_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/fsl_ifc_nand.c
@@ -20,7 +20,7 @@
 
 #define ERR_BYTE		0xFF /* Value returned for read
 					bytes when read failed	*/
-#define IFC_TIMEOUT_MSECS	500  /* Maximum number of mSecs to wait
+#define IFC_TIMEOUT_MSECS	1000 /* Maximum timeout to wait
 					for IFC NAND Machine	*/
 
 struct fsl_ifc_ctrl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/fsl_upm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/fsl_upm.c
@@ -135,7 +135,7 @@
 	unsigned int i;
 	int ret;
 
-	if (op->cs > NAND_MAX_CHIPS)
+	if (op->cs >= NAND_MAX_CHIPS)
 		return -EINVAL;
 
 	if (check_only)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/fsmc_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/fsmc_nand.c
@@ -15,6 +15,7 @@
 
 #include <linux/clk.h>
 #include <linux/completion.h>
+#include <linux/delay.h>
 #include <linux/dmaengine.h>
 #include <linux/dma-direction.h>
 #include <linux/dma-mapping.h>
@@ -93,6 +94,14 @@
 
 #define FSMC_BUSY_WAIT_TIMEOUT	(1 * HZ)
 
+/*
+ * According to SPEAr300 Reference Manual (RM0082)
+ *  TOUDEL = 7ns (Output delay from the flip-flops to the board)
+ *  TINDEL = 5ns (Input delay from the board to the flipflop)
+ */
+#define TOUTDEL	7000
+#define TINDEL	5000
+
 struct fsmc_nand_timings {
 	u8 tclr;
 	u8 tar;
@@ -277,7 +286,7 @@
 {
 	unsigned long hclk = clk_get_rate(host->clk);
 	unsigned long hclkn = NSEC_PER_SEC / hclk;
-	u32 thiz, thold, twait, tset;
+	u32 thiz, thold, twait, tset, twait_min;
 
 	if (sdrt->tRC_min < 30000)
 		return -EOPNOTSUPP;
@@ -309,13 +318,6 @@
 	else if (tims->thold > FSMC_THOLD_MASK)
 		tims->thold = FSMC_THOLD_MASK;
 
-	twait = max(sdrt->tRP_min, sdrt->tWP_min);
-	tims->twait = DIV_ROUND_UP(twait / 1000, hclkn) - 1;
-	if (tims->twait == 0)
-		tims->twait = 1;
-	else if (tims->twait > FSMC_TWAIT_MASK)
-		tims->twait = FSMC_TWAIT_MASK;
-
 	tset = max(sdrt->tCS_min - sdrt->tWP_min,
 		   sdrt->tCEA_max - sdrt->tREA_max);
 	tims->tset = DIV_ROUND_UP(tset / 1000, hclkn) - 1;
@@ -324,6 +326,21 @@
 	else if (tims->tset > FSMC_TSET_MASK)
 		tims->tset = FSMC_TSET_MASK;
 
+	/*
+	 * According to SPEAr300 Reference Manual (RM0082) which gives more
+	 * information related to FSMSC timings than the SPEAr600 one (RM0305),
+	 *   twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
+	 */
+	twait_min = sdrt->tCEA_max - ((tims->tset + 1) * hclkn * 1000)
+		    + TOUTDEL + TINDEL;
+	twait = max3(sdrt->tRP_min, sdrt->tWP_min, twait_min);
+
+	tims->twait = DIV_ROUND_UP(twait / 1000, hclkn) - 1;
+	if (tims->twait == 0)
+		tims->twait = 1;
+	else if (tims->twait > FSMC_TWAIT_MASK)
+		tims->twait = FSMC_TWAIT_MASK;
+
 	return 0;
 }
 
@@ -438,8 +455,10 @@
 			     unsigned char *read_ecc,
 			     unsigned char *calc_ecc)
 {
+	bool sm_order = chip->ecc.options & NAND_ECC_SOFT_HAMMING_SM_ORDER;
+
 	return ecc_sw_hamming_correct(buf, read_ecc, calc_ecc,
-				      chip->ecc.size, false);
+				      chip->ecc.size, sm_order);
 }
 
 /* Count the number of 0's in buff upto a max of max_bits */
@@ -662,6 +681,9 @@
 						instr->ctx.waitrdy.timeout_ms);
 			break;
 		}
+
+		if (instr->delay_ns)
+			ndelay(instr->delay_ns);
 	}
 
 	return ret;
@@ -1180,9 +1202,14 @@
 static int fsmc_nand_resume(struct device *dev)
 {
 	struct fsmc_nand_data *host = dev_get_drvdata(dev);
+	int ret;
 
 	if (host) {
-		clk_prepare_enable(host->clk);
+		ret = clk_prepare_enable(host->clk);
+		if (ret) {
+			dev_err(dev, "failed to enable clk\n");
+			return ret;
+		}
 		if (host->dev_timings)
 			fsmc_nand_setup(host, host->dev_timings);
 		nand_reset(&host->nand, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/gpio.c
@@ -163,9 +163,8 @@
 
 static int gpio_nand_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -365,6 +364,13 @@
 	if (gpiomtd->nwp && !IS_ERR(gpiomtd->nwp))
 		gpiod_direction_output(gpiomtd->nwp, 1);
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	ret = nand_scan(chip, 1);
 	if (ret)
 		goto err_wp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -644,40 +644,55 @@
  *         RDN_DELAY = -----------------------     {3}
  *                           RP
  */
-static void gpmi_nfc_compute_timings(struct gpmi_nand_data *this,
-				     const struct nand_sdr_timings *sdr)
+static int gpmi_nfc_compute_timings(struct gpmi_nand_data *this,
+				    const struct nand_sdr_timings *sdr)
 {
 	struct gpmi_nfc_hardware_timing *hw = &this->hw;
+	struct resources *r = &this->resources;
 	unsigned int dll_threshold_ps = this->devdata->max_chain_delay;
 	unsigned int period_ps, reference_period_ps;
 	unsigned int data_setup_cycles, data_hold_cycles, addr_setup_cycles;
 	unsigned int tRP_ps;
 	bool use_half_period;
 	int sample_delay_ps, sample_delay_factor;
-	u16 busy_timeout_cycles;
+	unsigned int busy_timeout_cycles;
 	u8 wrn_dly_sel;
+	unsigned long clk_rate, min_rate;
+	u64 busy_timeout_ps;
 
 	if (sdr->tRC_min >= 30000) {
 		/* ONFI non-EDO modes [0-3] */
 		hw->clk_rate = 22000000;
+		min_rate = 0;
 		wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS;
 	} else if (sdr->tRC_min >= 25000) {
 		/* ONFI EDO mode 4 */
 		hw->clk_rate = 80000000;
+		min_rate = 22000000;
 		wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
 	} else {
 		/* ONFI EDO mode 5 */
 		hw->clk_rate = 100000000;
+		min_rate = 80000000;
 		wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
 	}
 
+	clk_rate = clk_round_rate(r->clock[0], hw->clk_rate);
+	if (clk_rate <= min_rate) {
+		dev_err(this->dev, "clock setting: expected %ld, got %ld\n",
+			hw->clk_rate, clk_rate);
+		return -ENOTSUPP;
+	}
+
+	hw->clk_rate = clk_rate;
 	/* SDR core timings are given in picoseconds */
 	period_ps = div_u64((u64)NSEC_PER_SEC * 1000, hw->clk_rate);
 
 	addr_setup_cycles = TO_CYCLES(sdr->tALS_min, period_ps);
 	data_setup_cycles = TO_CYCLES(sdr->tDS_min, period_ps);
 	data_hold_cycles = TO_CYCLES(sdr->tDH_min, period_ps);
-	busy_timeout_cycles = TO_CYCLES(sdr->tWB_max + sdr->tR_max, period_ps);
+	busy_timeout_ps = max(sdr->tBERS_max, sdr->tPROG_max);
+	busy_timeout_cycles = TO_CYCLES(busy_timeout_ps, period_ps);
 
 	hw->timing0 = BF_GPMI_TIMING0_ADDRESS_SETUP(addr_setup_cycles) |
 		      BF_GPMI_TIMING0_DATA_HOLD(data_hold_cycles) |
@@ -711,16 +726,35 @@
 		hw->ctrl1n |= BF_GPMI_CTRL1_RDN_DELAY(sample_delay_factor) |
 			      BM_GPMI_CTRL1_DLL_ENABLE |
 			      (use_half_period ? BM_GPMI_CTRL1_HALF_PERIOD : 0);
+	return 0;
 }
 
-static void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
+static int gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
 {
 	struct gpmi_nfc_hardware_timing *hw = &this->hw;
 	struct resources *r = &this->resources;
 	void __iomem *gpmi_regs = r->gpmi_regs;
 	unsigned int dll_wait_time_us;
+	int ret;
 
-	clk_set_rate(r->clock[0], hw->clk_rate);
+	/* Clock dividers do NOT guarantee a clean clock signal on its output
+	 * during the change of the divide factor on i.MX6Q/UL/SX. On i.MX7/8,
+	 * all clock dividers provide these guarantee.
+	 */
+	if (GPMI_IS_MX6Q(this) || GPMI_IS_MX6SX(this))
+		clk_disable_unprepare(r->clock[0]);
+
+	ret = clk_set_rate(r->clock[0], hw->clk_rate);
+	if (ret) {
+		dev_err(this->dev, "cannot set clock rate to %lu Hz: %d\n", hw->clk_rate, ret);
+		return ret;
+	}
+
+	if (GPMI_IS_MX6Q(this) || GPMI_IS_MX6SX(this)) {
+		ret = clk_prepare_enable(r->clock[0]);
+		if (ret)
+			return ret;
+	}
 
 	writel(hw->timing0, gpmi_regs + HW_GPMI_TIMING0);
 	writel(hw->timing1, gpmi_regs + HW_GPMI_TIMING1);
@@ -739,6 +773,8 @@
 
 	/* Wait for the DLL to settle. */
 	udelay(dll_wait_time_us);
+
+	return 0;
 }
 
 static int gpmi_setup_interface(struct nand_chip *chip, int chipnr,
@@ -746,6 +782,7 @@
 {
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *sdr;
+	int ret;
 
 	/* Retrieve required NAND timings */
 	sdr = nand_get_sdr_timings(conf);
@@ -761,7 +798,9 @@
 		return 0;
 
 	/* Do the actual derivation of the controller timings */
-	gpmi_nfc_compute_timings(this, sdr);
+	ret = gpmi_nfc_compute_timings(this, sdr);
+	if (ret)
+		return ret;
 
 	this->hw.must_apply_timings = true;
 
@@ -1034,15 +1073,6 @@
 		r->clock[i] = clk;
 	}
 
-	if (GPMI_IS_MX6(this))
-		/*
-		 * Set the default value for the gpmi clock.
-		 *
-		 * If you want to use the ONFI nand which is in the
-		 * Synchronous Mode, you should change the clock as you need.
-		 */
-		clk_set_rate(r->clock[0], 22000000);
-
 	return 0;
 
 err_clock:
@@ -2280,7 +2310,9 @@
 	 */
 	if (this->hw.must_apply_timings) {
 		this->hw.must_apply_timings = false;
-		gpmi_nfc_apply_timings(this);
+		ret = gpmi_nfc_apply_timings(this);
+		if (ret)
+			goto out_pm;
 	}
 
 	dev_dbg(this->dev, "%s: %d instructions\n", __func__, op->ninstrs);
@@ -2409,6 +2441,7 @@
 
 	this->bch = false;
 
+out_pm:
 	pm_runtime_mark_last_busy(this->dev);
 	pm_runtime_put_autosuspend(this->dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
@@ -68,9 +68,14 @@
 	struct ingenic_ecc *ecc;
 
 	pdev = of_find_device_by_node(np);
-	if (!pdev || !platform_get_drvdata(pdev))
+	if (!pdev)
 		return ERR_PTR(-EPROBE_DEFER);
 
+	if (!platform_get_drvdata(pdev)) {
+		put_device(&pdev->dev);
+		return ERR_PTR(-EPROBE_DEFER);
+	}
+
 	ecc = platform_get_drvdata(pdev);
 	clk_prepare_enable(ecc->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
@@ -36,25 +36,25 @@
 void ingenic_ecc_release(struct ingenic_ecc *ecc);
 struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np);
 #else /* CONFIG_MTD_NAND_INGENIC_ECC */
-int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+static inline int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
 			  struct ingenic_ecc_params *params,
 			  const u8 *buf, u8 *ecc_code)
 {
 	return -ENODEV;
 }
 
-int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+static inline int ingenic_ecc_correct(struct ingenic_ecc *ecc,
 			struct ingenic_ecc_params *params, u8 *buf,
 			u8 *ecc_code)
 {
 	return -ENODEV;
 }
 
-void ingenic_ecc_release(struct ingenic_ecc *ecc)
+static inline void ingenic_ecc_release(struct ingenic_ecc *ecc)
 {
 }
 
-struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np)
+static inline struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np)
 {
 	return ERR_PTR(-ENODEV);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c
@@ -32,6 +32,7 @@
 	unsigned long addr_offset;
 	unsigned long cmd_offset;
 	const struct mtd_ooblayout_ops *oob_layout;
+	bool oob_first;
 };
 
 struct ingenic_nand_cs {
@@ -240,6 +241,9 @@
 	if (chip->bbt_options & NAND_BBT_USE_FLASH)
 		chip->bbt_options |= NAND_BBT_NO_OOB;
 
+	if (nfc->soc_info->oob_first)
+		chip->ecc.read_page = nand_read_page_hwecc_oob_first;
+
 	/* For legacy reasons we use a different layout on the qi,lb60 board. */
 	if (of_machine_is_compatible("qi,lb60"))
 		mtd_set_ooblayout(mtd, &qi_lb60_ooblayout_ops);
@@ -534,6 +538,7 @@
 	.data_offset = 0x00000000,
 	.cmd_offset = 0x00008000,
 	.addr_offset = 0x00010000,
+	.oob_first = true,
 };
 
 static const struct jz_soc_info jz4725b_soc_info = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/intel-nand-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/intel-nand-controller.c
@@ -16,6 +16,7 @@
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/nand.h>
 
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
@@ -580,6 +581,7 @@
 {
 	struct device *dev = &pdev->dev;
 	struct ebu_nand_controller *ebu_host;
+	struct device_node *chip_np;
 	struct nand_chip *nand;
 	struct mtd_info *mtd;
 	struct resource *res;
@@ -604,29 +606,42 @@
 	if (IS_ERR(ebu_host->hsnand))
 		return PTR_ERR(ebu_host->hsnand);
 
-	ret = device_property_read_u32(dev, "reg", &cs);
+	chip_np = of_get_next_child(dev->of_node, NULL);
+	if (!chip_np)
+		return dev_err_probe(dev, -EINVAL,
+				     "Could not find child node for the NAND chip\n");
+
+	ret = of_property_read_u32(chip_np, "reg", &cs);
 	if (ret) {
 		dev_err(dev, "failed to get chip select: %d\n", ret);
-		return ret;
+		goto err_of_node_put;
 	}
+	if (cs >= MAX_CS) {
+		dev_err(dev, "got invalid chip select: %d\n", cs);
+		ret = -EINVAL;
+		goto err_of_node_put;
+	}
+
 	ebu_host->cs_num = cs;
 
 	resname = devm_kasprintf(dev, GFP_KERNEL, "nand_cs%d", cs);
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, resname);
 	ebu_host->cs[cs].chipaddr = devm_ioremap_resource(dev, res);
-	ebu_host->cs[cs].nand_pa = res->start;
 	if (IS_ERR(ebu_host->cs[cs].chipaddr))
-		return PTR_ERR(ebu_host->cs[cs].chipaddr);
+		goto err_of_node_put;
+	ebu_host->cs[cs].nand_pa = res->start;
 
 	ebu_host->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(ebu_host->clk))
-		return dev_err_probe(dev, PTR_ERR(ebu_host->clk),
-				     "failed to get clock\n");
+	if (IS_ERR(ebu_host->clk)) {
+		ret = dev_err_probe(dev, PTR_ERR(ebu_host->clk),
+				    "failed to get clock\n");
+		goto err_of_node_put;
+	}
 
 	ret = clk_prepare_enable(ebu_host->clk);
 	if (ret) {
 		dev_err(dev, "failed to enable clock: %d\n", ret);
-		return ret;
+		goto err_of_node_put;
 	}
 	ebu_host->clk_rate = clk_get_rate(ebu_host->clk);
 
@@ -655,7 +670,7 @@
 	writel(ebu_host->cs[cs].addr_sel | EBU_ADDR_MASK(5) | EBU_ADDR_SEL_REGEN,
 	       ebu_host->ebu + EBU_ADDR_SEL(cs));
 
-	nand_set_flash_node(&ebu_host->chip, dev->of_node);
+	nand_set_flash_node(&ebu_host->chip, chip_np);
 
 	mtd = nand_to_mtd(&ebu_host->chip);
 	if (!mtd->name) {
@@ -691,6 +706,8 @@
 	ebu_dma_cleanup(ebu_host);
 err_disable_unprepare_clk:
 	clk_disable_unprepare(ebu_host->clk);
+err_of_node_put:
+	of_node_put(chip_np);
 
 	return ret;
 }
@@ -711,7 +728,6 @@
 }
 
 static const struct of_device_id ebu_nand_match[] = {
-	{ .compatible = "intel,nand-controller" },
 	{ .compatible = "intel,lgm-ebunand" },
 	{}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/lpc32xx_mlc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/lpc32xx_mlc.c
@@ -303,8 +303,9 @@
 	return 0;
 }
 
-static irqreturn_t lpc3xxx_nand_irq(int irq, struct lpc32xx_nand_host *host)
+static irqreturn_t lpc3xxx_nand_irq(int irq, void *data)
 {
+	struct lpc32xx_nand_host *host = data;
 	uint8_t sr;
 
 	/* Clear interrupt flag by reading status */
@@ -779,7 +780,7 @@
 		goto release_dma_chan;
 	}
 
-	if (request_irq(host->irq, (irq_handler_t)&lpc3xxx_nand_irq,
+	if (request_irq(host->irq, &lpc3xxx_nand_irq,
 			IRQF_TRIGGER_HIGH, DRV_NAME, host)) {
 		dev_err(&pdev->dev, "Error requesting NAND IRQ\n");
 		res = -ENXIO;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/marvell_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/marvell_nand.c
@@ -1148,6 +1148,7 @@
 		.ndcb[2] = NDCB2_ADDR5_PAGE(page),
 	};
 	unsigned int oob_bytes = lt->spare_bytes + (raw ? lt->ecc_bytes : 0);
+	u8 status;
 	int ret;
 
 	/* NFCv2 needs more information about the operation being executed */
@@ -1181,7 +1182,18 @@
 
 	ret = marvell_nfc_wait_op(chip,
 				  PSEC_TO_MSEC(sdr->tPROG_max));
-	return ret;
+	if (ret)
+		return ret;
+
+	/* Check write status on the chip side */
+	ret = nand_status_op(chip, &status);
+	if (ret)
+		return ret;
+
+	if (status & NAND_STATUS_FAIL)
+		return -EIO;
+
+	return 0;
 }
 
 static int marvell_nfc_hw_ecc_hmg_write_page_raw(struct nand_chip *chip,
@@ -1610,6 +1622,7 @@
 	int data_len = lt->data_bytes;
 	int spare_len = lt->spare_bytes;
 	int chunk, ret;
+	u8 status;
 
 	marvell_nfc_select_target(chip, chip->cur_cs);
 
@@ -1646,6 +1659,14 @@
 	if (ret)
 		return ret;
 
+	/* Check write status on the chip side */
+	ret = nand_status_op(chip, &status);
+	if (ret)
+		return ret;
+
+	if (status & NAND_STATUS_FAIL)
+		return -EIO;
+
 	return 0;
 }
 
@@ -2443,6 +2464,12 @@
 			NDTR1_WAIT_MODE;
 	}
 
+	/*
+	 * Reset nfc->selected_chip so the next command will cause the timing
+	 * registers to be updated in marvell_nfc_select_target().
+	 */
+	nfc->selected_chip = NULL;
+
 	return 0;
 }
 
@@ -2672,7 +2699,7 @@
 	chip->controller = &nfc->controller;
 	nand_set_flash_node(chip, np);
 
-	if (!of_property_read_bool(np, "marvell,nand-keep-config"))
+	if (of_property_read_bool(np, "marvell,nand-keep-config"))
 		chip->options |= NAND_KEEP_TIMINGS;
 
 	mtd = nand_to_mtd(chip);
@@ -2879,10 +2906,6 @@
 		regmap_update_bits(sysctrl_base, GENCONF_CLK_GATING_CTRL,
 				   GENCONF_CLK_GATING_CTRL_ND_GATE,
 				   GENCONF_CLK_GATING_CTRL_ND_GATE);
-
-		regmap_update_bits(sysctrl_base, GENCONF_ND_CLK_CTRL,
-				   GENCONF_ND_CLK_CTRL_EN,
-				   GENCONF_ND_CLK_CTRL_EN);
 	}
 
 	/* Configure the DMA if appropriate */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/meson_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/meson_nand.c
@@ -59,7 +59,7 @@
 #define CMDRWGEN(cmd_dir, ran, bch, short_mode, page_size, pages)	\
 	(								\
 		(cmd_dir)			|			\
-		((ran) << 19)			|			\
+		(ran)				|			\
 		((bch) << 14)			|			\
 		((short_mode) << 13)		|			\
 		(((page_size) & 0x7f) << 6)	|			\
@@ -72,6 +72,7 @@
 #define GENCMDIADDRH(aih, addr)		((aih) | (((addr) >> 16) & 0xffff))
 
 #define DMA_DIR(dir)		((dir) ? NFC_CMD_N2M : NFC_CMD_M2N)
+#define DMA_ADDR_ALIGN		8
 
 #define ECC_CHECK_RETURN_FF	(-1)
 
@@ -172,6 +173,7 @@
 
 	dma_addr_t daddr;
 	dma_addr_t iaddr;
+	u32 info_bytes;
 
 	unsigned long assigned_cs;
 };
@@ -275,7 +277,7 @@
 
 	if (raw) {
 		len = mtd->writesize + mtd->oobsize;
-		cmd = (len & GENMASK(5, 0)) | scrambler | DMA_DIR(dir);
+		cmd = (len & GENMASK(13, 0)) | scrambler | DMA_DIR(dir);
 		writel(cmd, nfc->reg_base + NFC_REG_CMD);
 		return;
 	}
@@ -454,7 +456,7 @@
 		if (ECC_ERR_CNT(*info) != ECC_UNCORRECTABLE) {
 			mtd->ecc_stats.corrected += ECC_ERR_CNT(*info);
 			*bitflips = max_t(u32, *bitflips, ECC_ERR_CNT(*info));
-			*correct_bitmap |= 1 >> i;
+			*correct_bitmap |= BIT_ULL(i);
 			continue;
 		}
 		if ((nand->options & NAND_NEED_SCRAMBLING) &&
@@ -499,6 +501,7 @@
 					 nfc->daddr, datalen, dir);
 			return ret;
 		}
+		nfc->info_bytes = infolen;
 		cmd = GENCMDIADDRL(NFC_CMD_AIL, nfc->iaddr);
 		writel(cmd, nfc->reg_base + NFC_REG_CMD);
 
@@ -516,8 +519,10 @@
 	struct meson_nfc *nfc = nand_get_controller_data(nand);
 
 	dma_unmap_single(nfc->dev, nfc->daddr, datalen, dir);
-	if (infolen)
+	if (infolen) {
 		dma_unmap_single(nfc->dev, nfc->iaddr, infolen, dir);
+		nfc->info_bytes = 0;
+	}
 }
 
 static int meson_nfc_read_buf(struct nand_chip *nand, u8 *buf, int len)
@@ -536,7 +541,7 @@
 	if (ret)
 		goto out;
 
-	cmd = NFC_CMD_N2M | (len & GENMASK(5, 0));
+	cmd = NFC_CMD_N2M | (len & GENMASK(13, 0));
 	writel(cmd, nfc->reg_base + NFC_REG_CMD);
 
 	meson_nfc_drain_cmd(nfc);
@@ -560,7 +565,7 @@
 	if (ret)
 		return ret;
 
-	cmd = NFC_CMD_M2N | (len & GENMASK(5, 0));
+	cmd = NFC_CMD_M2N | (len & GENMASK(13, 0));
 	writel(cmd, nfc->reg_base + NFC_REG_CMD);
 
 	meson_nfc_drain_cmd(nfc);
@@ -706,6 +711,8 @@
 		usleep_range(10, 15);
 		/* info is updated by nfc dma engine*/
 		smp_rmb();
+		dma_sync_single_for_cpu(nfc->dev, nfc->iaddr, nfc->info_bytes,
+					DMA_FROM_DEVICE);
 		ret = *info & ECC_COMPLETE;
 	} while (!ret);
 }
@@ -800,7 +807,7 @@
 			u8 *data = buf + i * ecc->size;
 			u8 *oob = nand->oob_poi + i * (ecc->bytes + 2);
 
-			if (correct_bitmap & (1 << i))
+			if (correct_bitmap & BIT_ULL(i))
 				continue;
 			ret = nand_check_erased_ecc_chunk(data,	ecc->size,
 							  oob, ecc->bytes + 2,
@@ -832,6 +839,9 @@
 
 static bool meson_nfc_is_buffer_dma_safe(const void *buffer)
 {
+	if ((uintptr_t)buffer % DMA_ADDR_ALIGN)
+		return false;
+
 	if (virt_addr_valid(buffer) && (!object_is_on_stack(buffer)))
 		return true;
 	return false;
@@ -1170,7 +1180,6 @@
 	struct meson_nfc *nfc = nand_get_controller_data(nand);
 	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
 	struct mtd_info *mtd = nand_to_mtd(nand);
-	int nsectors = mtd->writesize / 1024;
 	int ret;
 
 	if (!mtd->name) {
@@ -1188,7 +1197,7 @@
 	nand->options |= NAND_NO_SUBPAGE_WRITE;
 
 	ret = nand_ecc_choose_conf(nand, nfc->data->ecc_caps,
-				   mtd->oobsize - 2 * nsectors);
+				   mtd->oobsize - 2);
 	if (ret) {
 		dev_err(nfc->dev, "failed to ECC init\n");
 		return -EINVAL;
@@ -1307,7 +1316,6 @@
 		if (ret)
 			return ret;
 
-		meson_nfc_free_buffer(&meson_chip->nand);
 		nand_cleanup(&meson_chip->nand);
 		list_del(&meson_chip->node);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/mpc5121_nfc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/mpc5121_nfc.c
@@ -291,7 +291,6 @@
 /* Control chips select signal on ADS5121 board */
 static void ads5121_select_chip(struct nand_chip *nand, int chip)
 {
-	struct mtd_info *mtd = nand_to_mtd(nand);
 	struct mpc5121_nfc_prv *prv = nand_get_controller_data(nand);
 	u8 v;
 
@@ -605,9 +604,8 @@
 
 static int mpc5121_nfc_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -772,6 +770,13 @@
 		goto error;
 	}
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	/* Detect NAND chips */
 	retval = nand_scan(chip, be32_to_cpup(chips_no));
 	if (retval) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/mtk_ecc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/mtk_ecc.c
@@ -43,6 +43,7 @@
 
 struct mtk_ecc_caps {
 	u32 err_mask;
+	u32 err_shift;
 	const u8 *ecc_strength;
 	const u32 *ecc_regs;
 	u8 num_ecc_strength;
@@ -76,7 +77,7 @@
 };
 
 static const u8 ecc_strength_mt7622[] = {
-	4, 6, 8, 10, 12, 14, 16
+	4, 6, 8, 10, 12
 };
 
 enum mtk_ecc_regs {
@@ -221,7 +222,7 @@
 	for (i = 0; i < sectors; i++) {
 		offset = (i >> 2) << 2;
 		err = readl(ecc->regs + ECC_DECENUM0 + offset);
-		err = err >> ((i % 4) * 8);
+		err = err >> ((i % 4) * ecc->caps->err_shift);
 		err &= ecc->caps->err_mask;
 		if (err == ecc->caps->err_mask) {
 			/* uncorrectable errors */
@@ -449,6 +450,7 @@
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
 	.err_mask = 0x3f,
+	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2701,
 	.ecc_regs = mt2701_ecc_regs,
 	.num_ecc_strength = 20,
@@ -459,6 +461,7 @@
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
 	.err_mask = 0x7f,
+	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2712,
 	.ecc_regs = mt2712_ecc_regs,
 	.num_ecc_strength = 23,
@@ -468,10 +471,11 @@
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
-	.err_mask = 0x3f,
+	.err_mask = 0x1f,
+	.err_shift = 5,
 	.ecc_strength = ecc_strength_mt7622,
 	.ecc_regs = mt7622_ecc_regs,
-	.num_ecc_strength = 7,
+	.num_ecc_strength = 5,
 	.ecc_mode_shift = 4,
 	.parity_bits = 13,
 	.pg_irq_sel = 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/nand_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/nand_base.c
@@ -335,16 +335,19 @@
  *
  * Return: -EBUSY if the chip has been suspended, 0 otherwise
  */
-static int nand_get_device(struct nand_chip *chip)
+static void nand_get_device(struct nand_chip *chip)
 {
-	mutex_lock(&chip->lock);
-	if (chip->suspended) {
+	/* Wait until the device is resumed. */
+	while (1) {
+		mutex_lock(&chip->lock);
+		if (!chip->suspended) {
+			mutex_lock(&chip->controller->lock);
+			return;
+		}
 		mutex_unlock(&chip->lock);
-		return -EBUSY;
-	}
-	mutex_lock(&chip->controller->lock);
 
-	return 0;
+		wait_event(chip->resume_wq, !chip->suspended);
+	}
 }
 
 /**
@@ -447,9 +450,11 @@
 	 * if we don't do this. I have no clue why, but I seem to have 'fixed'
 	 * it in the doc2000 driver in August 1999.  dwmw2.
 	 */
-	ret = nand_reset(chip, chipnr);
-	if (ret)
-		return ret;
+	if (chip->parameters.onfi->jedec_id == NAND_MFR_TOSHIBA) {
+		ret = nand_reset(chip, chipnr);
+		if (ret)
+			return ret;
+	}
 
 	nand_select_target(chip, chipnr);
 
@@ -573,9 +578,7 @@
 		nand_erase_nand(chip, &einfo, 0);
 
 		/* Write bad block marker to OOB */
-		ret = nand_get_device(chip);
-		if (ret)
-			return ret;
+		nand_get_device(chip);
 
 		ret = nand_markbad_bbm(chip, ofs);
 		nand_release_device(chip);
@@ -926,7 +929,7 @@
 				 struct nand_sdr_timings *spec_timings)
 {
 	const struct nand_controller_ops *ops = chip->controller->ops;
-	int best_mode = 0, mode, ret;
+	int best_mode = 0, mode, ret = -EOPNOTSUPP;
 
 	iface->type = NAND_SDR_IFACE;
 
@@ -977,7 +980,7 @@
 				   struct nand_nvddr_timings *spec_timings)
 {
 	const struct nand_controller_ops *ops = chip->controller->ops;
-	int best_mode = 0, mode, ret;
+	int best_mode = 0, mode, ret = -EOPNOTSUPP;
 
 	iface->type = NAND_NVDDR_IFACE;
 
@@ -1088,28 +1091,32 @@
 				   unsigned int offset_in_page)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	bool ident_stage = !mtd->writesize;
 
-	/* Make sure the offset is less than the actual page size. */
-	if (offset_in_page > mtd->writesize + mtd->oobsize)
-		return -EINVAL;
+	/* Bypass all checks during NAND identification */
+	if (likely(!ident_stage)) {
+		/* Make sure the offset is less than the actual page size. */
+		if (offset_in_page > mtd->writesize + mtd->oobsize)
+			return -EINVAL;
 
-	/*
-	 * On small page NANDs, there's a dedicated command to access the OOB
-	 * area, and the column address is relative to the start of the OOB
-	 * area, not the start of the page. Asjust the address accordingly.
-	 */
-	if (mtd->writesize <= 512 && offset_in_page >= mtd->writesize)
-		offset_in_page -= mtd->writesize;
+		/*
+		 * On small page NANDs, there's a dedicated command to access the OOB
+		 * area, and the column address is relative to the start of the OOB
+		 * area, not the start of the page. Asjust the address accordingly.
+		 */
+		if (mtd->writesize <= 512 && offset_in_page >= mtd->writesize)
+			offset_in_page -= mtd->writesize;
 
-	/*
-	 * The offset in page is expressed in bytes, if the NAND bus is 16-bit
-	 * wide, then it must be divided by 2.
-	 */
-	if (chip->options & NAND_BUSWIDTH_16) {
-		if (WARN_ON(offset_in_page % 2))
-			return -EINVAL;
+		/*
+		 * The offset in page is expressed in bytes, if the NAND bus is 16-bit
+		 * wide, then it must be divided by 2.
+		 */
+		if (chip->options & NAND_BUSWIDTH_16) {
+			if (WARN_ON(offset_in_page % 2))
+				return -EINVAL;
 
-		offset_in_page /= 2;
+			offset_in_page /= 2;
+		}
 	}
 
 	addrs[0] = offset_in_page;
@@ -1118,7 +1125,7 @@
 	 * Small page NANDs use 1 cycle for the columns, while large page NANDs
 	 * need 2
 	 */
-	if (mtd->writesize <= 512)
+	if (!ident_stage && mtd->writesize <= 512)
 		return 1;
 
 	addrs[1] = offset_in_page >> 8;
@@ -1314,16 +1321,19 @@
 			       unsigned int len, bool force_8bit)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	bool ident_stage = !mtd->writesize;
 
 	if (len && !buf)
 		return -EINVAL;
 
-	if (offset_in_page + len > mtd->writesize + mtd->oobsize)
-		return -EINVAL;
+	if (!ident_stage) {
+		if (offset_in_page + len > mtd->writesize + mtd->oobsize)
+			return -EINVAL;
 
-	/* Small page NANDs do not support column change. */
-	if (mtd->writesize <= 512)
-		return -ENOTSUPP;
+		/* Small page NANDs do not support column change. */
+		if (mtd->writesize <= 512)
+			return -ENOTSUPP;
+	}
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_interface_config *conf =
@@ -1837,7 +1847,7 @@
 			NAND_OP_CMD(NAND_CMD_ERASE1, 0),
 			NAND_OP_ADDR(2, addrs, 0),
 			NAND_OP_CMD(NAND_CMD_ERASE2,
-				    NAND_COMMON_TIMING_MS(conf, tWB_max)),
+				    NAND_COMMON_TIMING_NS(conf, tWB_max)),
 			NAND_OP_WAIT_RDY(NAND_COMMON_TIMING_MS(conf, tBERS_max),
 					 0),
 		};
@@ -3161,6 +3171,73 @@
 }
 
 /**
+ * nand_read_page_hwecc_oob_first - Hardware ECC page read with ECC
+ *                                  data read from OOB area
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * Hardware ECC for large page chips, which requires the ECC data to be
+ * extracted from the OOB before the actual data is read.
+ */
+int nand_read_page_hwecc_oob_first(struct nand_chip *chip, uint8_t *buf,
+				   int oob_required, int page)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	int i, eccsize = chip->ecc.size, ret;
+	int eccbytes = chip->ecc.bytes;
+	int eccsteps = chip->ecc.steps;
+	uint8_t *p = buf;
+	uint8_t *ecc_code = chip->ecc.code_buf;
+	unsigned int max_bitflips = 0;
+
+	/* Read the OOB area first */
+	ret = nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize);
+	if (ret)
+		return ret;
+
+	/* Move read cursor to start of page */
+	ret = nand_change_read_column_op(chip, 0, NULL, 0, false);
+	if (ret)
+		return ret;
+
+	ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0,
+					 chip->ecc.total);
+	if (ret)
+		return ret;
+
+	for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+		int stat;
+
+		chip->ecc.hwctl(chip, NAND_ECC_READ);
+
+		ret = nand_read_data_op(chip, p, eccsize, false, false);
+		if (ret)
+			return ret;
+
+		stat = chip->ecc.correct(chip, p, &ecc_code[i], NULL);
+		if (stat == -EBADMSG &&
+		    (chip->ecc.options & NAND_ECC_GENERIC_ERASED_CHECK)) {
+			/* check for empty pages with bitflips */
+			stat = nand_check_erased_ecc_chunk(p, eccsize,
+							   &ecc_code[i],
+							   eccbytes, NULL, 0,
+							   chip->ecc.strength);
+		}
+
+		if (stat < 0) {
+			mtd->ecc_stats.failed++;
+		} else {
+			mtd->ecc_stats.corrected += stat;
+			max_bitflips = max_t(unsigned int, max_bitflips, stat);
+		}
+	}
+	return max_bitflips;
+}
+EXPORT_SYMBOL_GPL(nand_read_page_hwecc_oob_first);
+
+/**
  * nand_read_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page read
  * @chip: nand chip info structure
  * @buf: buffer to store read data
@@ -3756,9 +3833,7 @@
 	    ops->mode != MTD_OPS_RAW)
 		return -ENOTSUPP;
 
-	ret = nand_get_device(chip);
-	if (ret)
-		return ret;
+	nand_get_device(chip);
 
 	if (!ops->datbuf)
 		ret = nand_do_read_oob(chip, from, ops);
@@ -4345,13 +4420,11 @@
 			  struct mtd_oob_ops *ops)
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
-	int ret;
+	int ret = 0;
 
 	ops->retlen = 0;
 
-	ret = nand_get_device(chip);
-	if (ret)
-		return ret;
+	nand_get_device(chip);
 
 	switch (ops->mode) {
 	case MTD_OPS_PLACE_OOB:
@@ -4411,9 +4484,7 @@
 		return -EIO;
 
 	/* Grab the lock and see if the device is available */
-	ret = nand_get_device(chip);
-	if (ret)
-		return ret;
+	nand_get_device(chip);
 
 	/* Shift to get first page */
 	page = (int)(instr->addr >> chip->page_shift);
@@ -4500,7 +4571,7 @@
 	pr_debug("%s: called\n", __func__);
 
 	/* Grab the lock and see if the device is available */
-	WARN_ON(nand_get_device(chip));
+	nand_get_device(chip);
 	/* Release it and go back */
 	nand_release_device(chip);
 }
@@ -4517,9 +4588,7 @@
 	int ret;
 
 	/* Select the NAND device */
-	ret = nand_get_device(chip);
-	if (ret)
-		return ret;
+	nand_get_device(chip);
 
 	nand_select_target(chip, chipnr);
 
@@ -4590,6 +4659,8 @@
 			__func__);
 	}
 	mutex_unlock(&chip->lock);
+
+	wake_up_all(&chip->resume_wq);
 }
 
 /**
@@ -5367,6 +5438,7 @@
 	chip->cur_cs = -1;
 
 	mutex_init(&chip->lock);
+	init_waitqueue_head(&chip->resume_wq);
 
 	/* Enforce the right timings for reset/detection */
 	chip->current_interface_config = nand_get_reset_interface_config();
@@ -5987,6 +6059,7 @@
 static int nand_scan_tail(struct nand_chip *chip)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct nand_device *base = &chip->base;
 	struct nand_ecc_ctrl *ecc = &chip->ecc;
 	int ret, i;
 
@@ -6131,9 +6204,13 @@
 	if (!ecc->write_oob_raw)
 		ecc->write_oob_raw = ecc->write_oob;
 
-	/* propagate ecc info to mtd_info */
+	/* Propagate ECC info to the generic NAND and MTD layers */
 	mtd->ecc_strength = ecc->strength;
+	if (!base->ecc.ctx.conf.strength)
+		base->ecc.ctx.conf.strength = ecc->strength;
 	mtd->ecc_step_size = ecc->size;
+	if (!base->ecc.ctx.conf.step_size)
+		base->ecc.ctx.conf.step_size = ecc->size;
 
 	/*
 	 * Set the number of read / write steps for one page depending on ECC
@@ -6141,6 +6218,8 @@
 	 */
 	if (!ecc->steps)
 		ecc->steps = mtd->writesize / ecc->size;
+	if (!base->ecc.ctx.nsteps)
+		base->ecc.ctx.nsteps = ecc->steps;
 	if (ecc->steps * ecc->size != mtd->writesize) {
 		WARN(1, "Invalid ECC parameters\n");
 		ret = -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/nand_hynix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/nand_hynix.c
@@ -402,7 +402,7 @@
 	if (ret)
 		pr_warn("failed to initialize read-retry infrastructure");
 
-	return 0;
+	return ret;
 }
 
 static void hynix_nand_extract_oobsize(struct nand_chip *chip,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/nand_onfi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/nand_onfi.c
@@ -319,6 +319,7 @@
 	onfi->sdr_timing_modes = le16_to_cpu(p->sdr_timing_modes);
 	if (le16_to_cpu(p->features) & ONFI_FEATURE_NV_DDR)
 		onfi->nvddr_timing_modes = le16_to_cpu(p->nvddr_timing_modes);
+	onfi->jedec_id = le16_to_cpu(p->jedec_id);
 	onfi->vendor_revision = le16_to_cpu(p->vendor_revision);
 	memcpy(onfi->vendor, p->vendor, sizeof(p->vendor));
 	chip->parameters.onfi = onfi;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/omap_elm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/omap_elm.c
@@ -177,17 +177,17 @@
 			switch (info->bch_type) {
 			case BCH8_ECC:
 				/* syndrome fragment 0 = ecc[9-12B] */
-				val = cpu_to_be32(*(u32 *) &ecc[9]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[9]);
 				elm_write_reg(info, offset, val);
 
 				/* syndrome fragment 1 = ecc[5-8B] */
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[5]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[5]);
 				elm_write_reg(info, offset, val);
 
 				/* syndrome fragment 2 = ecc[1-4B] */
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[1]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[1]);
 				elm_write_reg(info, offset, val);
 
 				/* syndrome fragment 3 = ecc[0B] */
@@ -197,35 +197,35 @@
 				break;
 			case BCH4_ECC:
 				/* syndrome fragment 0 = ecc[20-52b] bits */
-				val = (cpu_to_be32(*(u32 *) &ecc[3]) >> 4) |
+				val = ((__force u32)cpu_to_be32(*(u32 *)&ecc[3]) >> 4) |
 					((ecc[2] & 0xf) << 28);
 				elm_write_reg(info, offset, val);
 
 				/* syndrome fragment 1 = ecc[0-20b] bits */
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[0]) >> 12;
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[0]) >> 12;
 				elm_write_reg(info, offset, val);
 				break;
 			case BCH16_ECC:
-				val = cpu_to_be32(*(u32 *) &ecc[22]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[22]);
 				elm_write_reg(info, offset, val);
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[18]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[18]);
 				elm_write_reg(info, offset, val);
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[14]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[14]);
 				elm_write_reg(info, offset, val);
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[10]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[10]);
 				elm_write_reg(info, offset, val);
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[6]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[6]);
 				elm_write_reg(info, offset, val);
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[2]);
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[2]);
 				elm_write_reg(info, offset, val);
 				offset += 4;
-				val = cpu_to_be32(*(u32 *) &ecc[0]) >> 16;
+				val = (__force u32)cpu_to_be32(*(u32 *)&ecc[0]) >> 16;
 				elm_write_reg(info, offset, val);
 				break;
 			default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/orion_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/orion_nand.c
@@ -85,9 +85,8 @@
 
 static int orion_nand_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -190,6 +189,13 @@
 		return ret;
 	}
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	nc->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	ret = nand_scan(nc, 1);
 	if (ret)
 		goto no_dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/pasemi_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/pasemi_nand.c
@@ -75,9 +75,8 @@
 
 static int pasemi_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -154,6 +153,13 @@
 	/* Enable the following for a flash based bad block table */
 	chip->bbt_options = NAND_BBT_USE_FLASH;
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	/* Scan to find existence of the device */
 	err = nand_scan(chip, 1);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/pl35x-nand-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/pl35x-nand-controller.c
@@ -513,6 +513,7 @@
 	u32 addr1 = 0, addr2 = 0, row;
 	u32 cmd_addr;
 	int i, ret;
+	u8 status;
 
 	ret = pl35x_smc_set_ecc_mode(nfc, chip, PL35X_SMC_ECC_CFG_MODE_APB);
 	if (ret)
@@ -565,6 +566,14 @@
 	if (ret)
 		goto disable_ecc_engine;
 
+	/* Check write status on the chip side */
+	ret = nand_status_op(chip, &status);
+	if (ret)
+		goto disable_ecc_engine;
+
+	if (status & NAND_STATUS_FAIL)
+		ret = -EIO;
+
 disable_ecc_engine:
 	pl35x_smc_set_ecc_mode(nfc, chip, PL35X_SMC_ECC_CFG_MODE_BYPASS);
 
@@ -1062,7 +1071,7 @@
 	chip->controller = &nfc->controller;
 	mtd = nand_to_mtd(chip);
 	mtd->dev.parent = nfc->dev;
-	nand_set_flash_node(chip, nfc->dev->of_node);
+	nand_set_flash_node(chip, np);
 	if (!mtd->name) {
 		mtd->name = devm_kasprintf(nfc->dev, GFP_KERNEL,
 					   "%s", PL35X_NANDC_DRIVER_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/plat_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/plat_nand.c
@@ -21,9 +21,8 @@
 
 static int plat_nand_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -94,6 +93,13 @@
 			goto out;
 	}
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	data->chip.ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	/* Scan to find existence of the device */
 	err = nand_scan(&data->chip, pdata->chip.nr_chips);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/qcom_nandc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/qcom_nandc.c
@@ -2,7 +2,6 @@
 /*
  * Copyright (c) 2016, The Linux Foundation. All rights reserved.
  */
-
 #include <linux/clk.h>
 #include <linux/slab.h>
 #include <linux/bitops.h>
@@ -2642,10 +2641,23 @@
 	ecc->engine_type = NAND_ECC_ENGINE_TYPE_ON_HOST;
 
 	mtd_set_ooblayout(mtd, &qcom_nand_ooblayout_ops);
+	/* Free the initially allocated BAM transaction for reading the ONFI params */
+	if (nandc->props->is_bam)
+		free_bam_transaction(nandc);
 
 	nandc->max_cwperpage = max_t(unsigned int, nandc->max_cwperpage,
 				     cwperpage);
 
+	/* Now allocate the BAM transaction based on updated max_cwperpage */
+	if (nandc->props->is_bam) {
+		nandc->bam_txn = alloc_bam_transaction(nandc);
+		if (!nandc->bam_txn) {
+			dev_err(nandc->dev,
+				"failed to allocate bam transaction\n");
+			return -ENOMEM;
+		}
+	}
+
 	/*
 	 * DATA_UD_BYTES varies based on whether the read/write command protects
 	 * spare data with ECC too. We protect spare data by default, so we set
@@ -2946,17 +2958,6 @@
 	if (ret)
 		return ret;
 
-	if (nandc->props->is_bam) {
-		free_bam_transaction(nandc);
-		nandc->bam_txn = alloc_bam_transaction(nandc);
-		if (!nandc->bam_txn) {
-			dev_err(nandc->dev,
-				"failed to allocate bam transaction\n");
-			nand_cleanup(chip);
-			return -ENOMEM;
-		}
-	}
-
 	ret = mtd_device_parse_register(mtd, probes, NULL, NULL, 0);
 	if (ret)
 		nand_cleanup(chip);
@@ -3063,10 +3064,6 @@
 	if (dma_mapping_error(dev, nandc->base_dma))
 		return -ENXIO;
 
-	ret = qcom_nandc_alloc(nandc);
-	if (ret)
-		goto err_nandc_alloc;
-
 	ret = clk_prepare_enable(nandc->core_clk);
 	if (ret)
 		goto err_core_clk;
@@ -3075,6 +3072,10 @@
 	if (ret)
 		goto err_aon_clk;
 
+	ret = qcom_nandc_alloc(nandc);
+	if (ret)
+		goto err_nandc_alloc;
+
 	ret = qcom_nandc_setup(nandc);
 	if (ret)
 		goto err_setup;
@@ -3086,15 +3087,14 @@
 	return 0;
 
 err_setup:
+	qcom_nandc_unalloc(nandc);
+err_nandc_alloc:
 	clk_disable_unprepare(nandc->aon_clk);
 err_aon_clk:
 	clk_disable_unprepare(nandc->core_clk);
 err_core_clk:
-	qcom_nandc_unalloc(nandc);
-err_nandc_alloc:
-	dma_unmap_resource(dev, res->start, resource_size(res),
+	dma_unmap_resource(dev, nandc->base_dma, resource_size(res),
 			   DMA_BIDIRECTIONAL, 0);
-
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/rockchip-nand-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/rockchip-nand-controller.c
@@ -421,13 +421,13 @@
 	u32 rate, tc2rw, trwpw, trw2c;
 	u32 temp;
 
-	if (target < 0)
-		return 0;
-
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))
 		return -EOPNOTSUPP;
 
+	if (target < 0)
+		return 0;
+
 	if (IS_ERR(nfc->nfc_clk))
 		rate = clk_get_rate(nfc->ahb_clk);
 	else
@@ -562,9 +562,10 @@
 		 *    BBM  OOB1 OOB2 OOB3 |......|  PA0  PA1  PA2  PA3
 		 *
 		 * The rk_nfc_ooblayout_free() function already has reserved
-		 * these 4 bytes with:
+		 * these 4 bytes together with 2 bytes for BBM
+		 * by reducing it's length:
 		 *
-		 * oob_region->offset = NFC_SYS_DATA_SIZE + 2;
+		 * oob_region->length = rknand->metadata_size - NFC_SYS_DATA_SIZE - 2;
 		 */
 		if (!i)
 			memcpy(rk_nfc_oob_ptr(chip, i),
@@ -597,7 +598,7 @@
 	int pages_per_blk = mtd->erasesize / mtd->writesize;
 	int ret = 0, i, boot_rom_mode = 0;
 	dma_addr_t dma_data, dma_oob;
-	u32 reg;
+	u32 tmp;
 	u8 *oob;
 
 	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
@@ -624,6 +625,13 @@
 	 *
 	 *   0xFF 0xFF 0xFF 0xFF | BBM OOB1 OOB2 OOB3 | ...
 	 *
+	 * The code here just swaps the first 4 bytes with the last
+	 * 4 bytes without losing any data.
+	 *
+	 * The chip->oob_poi data layout:
+	 *
+	 *    BBM  OOB1 OOB2 OOB3 |......|  PA0  PA1  PA2  PA3
+	 *
 	 * Configure the ECC algorithm supported by the boot ROM.
 	 */
 	if ((page < (pages_per_blk * rknand->boot_blks)) &&
@@ -634,21 +642,17 @@
 	}
 
 	for (i = 0; i < ecc->steps; i++) {
-		if (!i) {
-			reg = 0xFFFFFFFF;
-		} else {
+		if (!i)
+			oob = chip->oob_poi + (ecc->steps - 1) * NFC_SYS_DATA_SIZE;
+		else
 			oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
-			reg = oob[0] | oob[1] << 8 | oob[2] << 16 |
-			      oob[3] << 24;
-		}
 
-		if (!i && boot_rom_mode)
-			reg = (page & (pages_per_blk - 1)) * 4;
+		tmp = oob[0] | oob[1] << 8 | oob[2] << 16 | oob[3] << 24;
 
 		if (nfc->cfg->type == NFC_V9)
-			nfc->oob_buf[i] = reg;
+			nfc->oob_buf[i] = tmp;
 		else
-			nfc->oob_buf[i * (oob_step / 4)] = reg;
+			nfc->oob_buf[i * (oob_step / 4)] = tmp;
 	}
 
 	dma_data = dma_map_single(nfc->dev, (void *)nfc->page_buf,
@@ -811,12 +815,17 @@
 		goto timeout_err;
 	}
 
-	for (i = 1; i < ecc->steps; i++) {
-		oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
+	for (i = 0; i < ecc->steps; i++) {
+		if (!i)
+			oob = chip->oob_poi + (ecc->steps - 1) * NFC_SYS_DATA_SIZE;
+		else
+			oob = chip->oob_poi + (i - 1) * NFC_SYS_DATA_SIZE;
+
 		if (nfc->cfg->type == NFC_V9)
 			tmp = nfc->oob_buf[i];
 		else
 			tmp = nfc->oob_buf[i * (oob_step / 4)];
+
 		*oob++ = (u8)tmp;
 		*oob++ = (u8)(tmp >> 8);
 		*oob++ = (u8)(tmp >> 16);
@@ -935,12 +944,8 @@
 	if (section)
 		return -ERANGE;
 
-	/*
-	 * The beginning of the OOB area stores the reserved data for the NFC,
-	 * the size of the reserved data is NFC_SYS_DATA_SIZE bytes.
-	 */
 	oob_region->length = rknand->metadata_size - NFC_SYS_DATA_SIZE - 2;
-	oob_region->offset = NFC_SYS_DATA_SIZE + 2;
+	oob_region->offset = 2;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/sh_flctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/sh_flctl.c
@@ -384,7 +384,8 @@
 	dma_addr_t dma_addr;
 	dma_cookie_t cookie;
 	uint32_t reg;
-	int ret;
+	int ret = 0;
+	unsigned long time_left;
 
 	if (dir == DMA_FROM_DEVICE) {
 		chan = flctl->chan_fifo0_rx;
@@ -425,13 +426,14 @@
 		goto out;
 	}
 
-	ret =
+	time_left =
 	wait_for_completion_timeout(&flctl->dma_complete,
 				msecs_to_jiffies(3000));
 
-	if (ret <= 0) {
+	if (time_left == 0) {
 		dmaengine_terminate_all(chan);
 		dev_err(&flctl->pdev->dev, "wait_for_completion_timeout\n");
+		ret = -ETIMEDOUT;
 	}
 
 out:
@@ -441,7 +443,7 @@
 
 	dma_unmap_single(chan->device->dev, dma_addr, len, dir);
 
-	/* ret > 0 is success */
+	/* ret == 0 is success */
 	return ret;
 }
 
@@ -465,7 +467,7 @@
 
 	/* initiate DMA transfer */
 	if (flctl->chan_fifo0_rx && rlen >= 32 &&
-		flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_FROM_DEVICE) > 0)
+		!flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_FROM_DEVICE))
 			goto convert;	/* DMA success */
 
 	/* do polling transfer */
@@ -524,7 +526,7 @@
 
 	/* initiate DMA transfer */
 	if (flctl->chan_fifo0_tx && rlen >= 32 &&
-		flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_TO_DEVICE) > 0)
+		!flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_TO_DEVICE))
 			return;	/* DMA success */
 
 	/* do polling transfer */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/socrates_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/socrates_nand.c
@@ -119,9 +119,8 @@
 
 static int socrates_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -175,6 +174,13 @@
 	/* TODO: I have no idea what real delay is. */
 	nand_chip->legacy.chip_delay = 20;	/* 20us command delay time */
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	nand_chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	dev_set_drvdata(&ofdev->dev, host);
 
 	res = nand_scan(nand_chip, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/stm32_fmc2_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/stm32_fmc2_nand.c
@@ -1527,6 +1527,9 @@
 	if (IS_ERR(sdrt))
 		return PTR_ERR(sdrt);
 
+	if (conf->timings.mode > 3)
+		return -EOPNOTSUPP;
+
 	if (chipnr == NAND_DATA_IFACE_CHECK_ONLY)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/sunxi_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/sunxi_nand.c
@@ -1609,7 +1609,7 @@
 	if (section < ecc->steps)
 		oobregion->length = 4;
 	else
-		oobregion->offset = mtd->oobsize - oobregion->offset;
+		oobregion->length = mtd->oobsize - oobregion->offset;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/raw/xway_nand.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/raw/xway_nand.c
@@ -148,9 +148,8 @@
 
 static int xway_attach_chip(struct nand_chip *chip)
 {
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-
-	if (chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
 		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
 
 	return 0;
@@ -219,6 +218,13 @@
 		    | NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P
 		    | cs_flag, EBU_NAND_CON);
 
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	data->chip.ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
 	/* Scan to find existence of the device */
 	err = nand_scan(&data->chip, 1);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/spi/gigadevice.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/spi/gigadevice.c
@@ -39,6 +39,14 @@
 		SPINAND_PAGE_READ_FROM_CACHE_OP_3A(true, 0, 1, NULL, 0),
 		SPINAND_PAGE_READ_FROM_CACHE_OP_3A(false, 0, 0, NULL, 0));
 
+static SPINAND_OP_VARIANTS(read_cache_variants_1gq5,
+		SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(0, 2, NULL, 0),
+		SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0),
+		SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP(0, 1, NULL, 0),
+		SPINAND_PAGE_READ_FROM_CACHE_X2_OP(0, 1, NULL, 0),
+		SPINAND_PAGE_READ_FROM_CACHE_OP(true, 0, 1, NULL, 0),
+		SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0));
+
 static SPINAND_OP_VARIANTS(write_cache_variants,
 		SPINAND_PROG_LOAD_X4(true, 0, NULL, 0),
 		SPINAND_PROG_LOAD(true, 0, NULL, 0));
@@ -170,7 +178,7 @@
 {
 	u8 status2;
 	struct spi_mem_op op = SPINAND_GET_FEATURE_OP(GD5FXGQXXEXXG_REG_STATUS2,
-						      &status2);
+						      spinand->scratchbuf);
 	int ret;
 
 	switch (status & STATUS_ECC_MASK) {
@@ -191,6 +199,7 @@
 		 * report the maximum of 4 in this case
 		 */
 		/* bits sorted this way (3...0): ECCS1,ECCS0,ECCSE1,ECCSE0 */
+		status2 = *(spinand->scratchbuf);
 		return ((status & STATUS_ECC_MASK) >> 2) |
 			((status2 & STATUS_ECC_MASK) >> 4);
 
@@ -212,7 +221,7 @@
 {
 	u8 status2;
 	struct spi_mem_op op = SPINAND_GET_FEATURE_OP(GD5FXGQXXEXXG_REG_STATUS2,
-						      &status2);
+						      spinand->scratchbuf);
 	int ret;
 
 	switch (status & STATUS_ECC_MASK) {
@@ -232,6 +241,7 @@
 		 * 1 ... 4 bits are flipped (and corrected)
 		 */
 		/* bits sorted this way (1...0): ECCSE1, ECCSE0 */
+		status2 = *(spinand->scratchbuf);
 		return ((status2 & STATUS_ECC_MASK) >> 4) + 1;
 
 	case STATUS_ECC_UNCOR_ERROR:
@@ -339,7 +349,7 @@
 		     SPINAND_ID(SPINAND_READID_METHOD_OPCODE_DUMMY, 0x51),
 		     NAND_MEMORG(1, 2048, 128, 64, 1024, 20, 1, 1, 1),
 		     NAND_ECCREQ(4, 512),
-		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants_1gq5,
 					      &write_cache_variants,
 					      &update_cache_variants),
 		     SPINAND_HAS_QE_BIT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/spi/micron.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/spi/micron.c
@@ -12,7 +12,7 @@
 
 #define SPINAND_MFR_MICRON		0x2c
 
-#define MICRON_STATUS_ECC_MASK		GENMASK(7, 4)
+#define MICRON_STATUS_ECC_MASK		GENMASK(6, 4)
 #define MICRON_STATUS_ECC_NO_BITFLIPS	(0 << 4)
 #define MICRON_STATUS_ECC_1TO3_BITFLIPS	(1 << 4)
 #define MICRON_STATUS_ECC_4TO6_BITFLIPS	(3 << 4)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/nand/spi/toshiba.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/nand/spi/toshiba.c
@@ -73,7 +73,7 @@
 {
 	struct nand_device *nand = spinand_to_nand(spinand);
 	u8 mbf = 0;
-	struct spi_mem_op op = SPINAND_GET_FEATURE_OP(0x30, &mbf);
+	struct spi_mem_op op = SPINAND_GET_FEATURE_OP(0x30, spinand->scratchbuf);
 
 	switch (status & STATUS_ECC_MASK) {
 	case STATUS_ECC_NO_BITFLIPS:
@@ -92,7 +92,7 @@
 		if (spi_mem_exec_op(spinand->spimem, &op))
 			return nanddev_get_ecc_conf(nand)->strength;
 
-		mbf >>= 4;
+		mbf = *(spinand->scratchbuf) >> 4;
 
 		if (WARN_ON(mbf > nanddev_get_ecc_conf(nand)->strength || !mbf))
 			return nanddev_get_ecc_conf(nand)->strength;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/parsers/bcm47xxpart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/parsers/bcm47xxpart.c
@@ -233,11 +233,11 @@
 		}
 
 		/* Read middle of the block */
-		err = mtd_read(master, offset + 0x8000, 0x4, &bytes_read,
+		err = mtd_read(master, offset + (blocksize / 2), 0x4, &bytes_read,
 			       (uint8_t *)buf);
 		if (err && !mtd_is_bitflip(err)) {
 			pr_err("mtd_read error while parsing (offset: 0x%X): %d\n",
-			       offset, err);
+			       offset + (blocksize / 2), err);
 			continue;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/parsers/ofpart_bcm4908.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/parsers/ofpart_bcm4908.c
@@ -35,12 +35,15 @@
 		err = kstrtoul(s + len + 1, 0, &offset);
 		if (err) {
 			pr_err("failed to parse %s\n", s + len + 1);
+			of_node_put(root);
 			return err;
 		}
 
+		of_node_put(root);
 		return offset << 10;
 	}
 
+	of_node_put(root);
 	return -ENOENT;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/parsers/qcomsmempart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/parsers/qcomsmempart.c
@@ -58,11 +58,11 @@
 			       const struct mtd_partition **pparts,
 			       struct mtd_part_parser_data *data)
 {
+	size_t len = SMEM_FLASH_PTABLE_HDR_LEN;
+	int ret, i, j, tmpparts, numparts = 0;
 	struct smem_flash_pentry *pentry;
 	struct smem_flash_ptable *ptable;
-	size_t len = SMEM_FLASH_PTABLE_HDR_LEN;
 	struct mtd_partition *parts;
-	int ret, i, numparts;
 	char *name, *c;
 
 	if (IS_ENABLED(CONFIG_MTD_SPI_NOR_USE_4K_SECTORS)
@@ -87,8 +87,8 @@
 	}
 
 	/* Ensure that # of partitions is less than the max we have allocated */
-	numparts = le32_to_cpu(ptable->numparts);
-	if (numparts > SMEM_FLASH_PTABLE_MAX_PARTS_V4) {
+	tmpparts = le32_to_cpu(ptable->numparts);
+	if (tmpparts > SMEM_FLASH_PTABLE_MAX_PARTS_V4) {
 		pr_err("Partition numbers exceed the max limit\n");
 		return -EINVAL;
 	}
@@ -116,11 +116,17 @@
 		return PTR_ERR(ptable);
 	}
 
+	for (i = 0; i < tmpparts; i++) {
+		pentry = &ptable->pentry[i];
+		if (pentry->name[0] != '\0')
+			numparts++;
+	}
+
 	parts = kcalloc(numparts, sizeof(*parts), GFP_KERNEL);
 	if (!parts)
 		return -ENOMEM;
 
-	for (i = 0; i < numparts; i++) {
+	for (i = 0, j = 0; i < tmpparts; i++) {
 		pentry = &ptable->pentry[i];
 		if (pentry->name[0] == '\0')
 			continue;
@@ -135,24 +141,25 @@
 		for (c = name; *c != '\0'; c++)
 			*c = tolower(*c);
 
-		parts[i].name = name;
-		parts[i].offset = le32_to_cpu(pentry->offset) * mtd->erasesize;
-		parts[i].mask_flags = pentry->attr;
-		parts[i].size = le32_to_cpu(pentry->length) * mtd->erasesize;
+		parts[j].name = name;
+		parts[j].offset = le32_to_cpu(pentry->offset) * mtd->erasesize;
+		parts[j].mask_flags = pentry->attr;
+		parts[j].size = le32_to_cpu(pentry->length) * mtd->erasesize;
 		pr_debug("%d: %s offs=0x%08x size=0x%08x attr:0x%08x\n",
 			 i, pentry->name, le32_to_cpu(pentry->offset),
 			 le32_to_cpu(pentry->length), pentry->attr);
+		j++;
 	}
 
 	pr_debug("SMEM partition table found: ver: %d len: %d\n",
-		 le32_to_cpu(ptable->version), numparts);
+		 le32_to_cpu(ptable->version), tmpparts);
 	*pparts = parts;
 
 	return numparts;
 
 out_free_parts:
-	while (--i >= 0)
-		kfree(parts[i].name);
+	while (--j >= 0)
+		kfree(parts[j].name);
 	kfree(parts);
 	*pparts = NULL;
 
@@ -166,6 +173,8 @@
 
 	for (i = 0; i < nr_parts; i++)
 		kfree(pparts[i].name);
+
+	kfree(pparts);
 }
 
 static const struct of_device_id qcomsmem_of_match_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/parsers/redboot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/parsers/redboot.c
@@ -58,6 +58,7 @@
 		return;
 
 	ret = of_property_read_u32(npart, "fis-index-block", &dirblock);
+	of_node_put(npart);
 	if (ret)
 		return;
 
@@ -101,7 +102,7 @@
 			offset -= master->erasesize;
 		}
 	} else {
-		offset = directory * master->erasesize;
+		offset = (unsigned long) directory * master->erasesize;
 		while (mtd_block_isbad(master, offset)) {
 			offset += master->erasesize;
 			if (offset == master->size)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/sm_ftl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/sm_ftl.c
@@ -1111,9 +1111,9 @@
 {
 	struct sm_ftl *ftl = dev->priv;
 
-	mutex_lock(&ftl->mutex);
 	del_timer_sync(&ftl->timer);
 	cancel_work_sync(&ftl->flush_work);
+	mutex_lock(&ftl->mutex);
 	sm_cache_flush(ftl);
 	mutex_unlock(&ftl->mutex);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/controllers/hisi-sfc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/controllers/hisi-sfc.c
@@ -477,7 +477,6 @@
 
 	hisi_spi_nor_unregister_all(host);
 	mutex_destroy(&host->lock);
-	clk_disable_unprepare(host->clk);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/controllers/intel-spi-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/controllers/intel-spi-pci.c
@@ -16,12 +16,30 @@
 #define BCR		0xdc
 #define BCR_WPD		BIT(0)
 
+static bool intel_spi_pci_set_writeable(void __iomem *base, void *data)
+{
+	struct pci_dev *pdev = data;
+	u32 bcr;
+
+	/* Try to make the chip read/write */
+	pci_read_config_dword(pdev, BCR, &bcr);
+	if (!(bcr & BCR_WPD)) {
+		bcr |= BCR_WPD;
+		pci_write_config_dword(pdev, BCR, bcr);
+		pci_read_config_dword(pdev, BCR, &bcr);
+	}
+
+	return bcr & BCR_WPD;
+}
+
 static const struct intel_spi_boardinfo bxt_info = {
 	.type = INTEL_SPI_BXT,
+	.set_writeable = intel_spi_pci_set_writeable,
 };
 
 static const struct intel_spi_boardinfo cnl_info = {
 	.type = INTEL_SPI_CNL,
+	.set_writeable = intel_spi_pci_set_writeable,
 };
 
 static int intel_spi_pci_probe(struct pci_dev *pdev,
@@ -29,7 +47,6 @@
 {
 	struct intel_spi_boardinfo *info;
 	struct intel_spi *ispi;
-	u32 bcr;
 	int ret;
 
 	ret = pcim_enable_device(pdev);
@@ -41,15 +58,7 @@
 	if (!info)
 		return -ENOMEM;
 
-	/* Try to make the chip read/write */
-	pci_read_config_dword(pdev, BCR, &bcr);
-	if (!(bcr & BCR_WPD)) {
-		bcr |= BCR_WPD;
-		pci_write_config_dword(pdev, BCR, bcr);
-		pci_read_config_dword(pdev, BCR, &bcr);
-	}
-	info->writeable = !!(bcr & BCR_WPD);
-
+	info->data = pdev;
 	ispi = intel_spi_probe(&pdev->dev, &pdev->resource[0], info);
 	if (IS_ERR(ispi))
 		return PTR_ERR(ispi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/controllers/intel-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/controllers/intel-spi.c
@@ -52,17 +52,17 @@
 #define FRACC				0x50
 
 #define FREG(n)				(0x54 + ((n) * 4))
-#define FREG_BASE_MASK			0x3fff
+#define FREG_BASE_MASK			GENMASK(14, 0)
 #define FREG_LIMIT_SHIFT		16
-#define FREG_LIMIT_MASK			(0x03fff << FREG_LIMIT_SHIFT)
+#define FREG_LIMIT_MASK			GENMASK(30, 16)
 
 /* Offset is from @ispi->pregs */
 #define PR(n)				((n) * 4)
 #define PR_WPE				BIT(31)
 #define PR_LIMIT_SHIFT			16
-#define PR_LIMIT_MASK			(0x3fff << PR_LIMIT_SHIFT)
+#define PR_LIMIT_MASK			GENMASK(30, 16)
 #define PR_RPE				BIT(15)
-#define PR_BASE_MASK			0x3fff
+#define PR_BASE_MASK			GENMASK(14, 0)
 
 /* Offsets are from @ispi->sregs */
 #define SSFSTS_CTL			0x00
@@ -116,7 +116,7 @@
 #define ERASE_OPCODE_SHIFT		8
 #define ERASE_OPCODE_MASK		(0xff << ERASE_OPCODE_SHIFT)
 #define ERASE_64K_OPCODE_SHIFT		16
-#define ERASE_64K_OPCODE_MASK		(0xff << ERASE_OPCODE_SHIFT)
+#define ERASE_64K_OPCODE_MASK		(0xff << ERASE_64K_OPCODE_SHIFT)
 
 #define INTEL_SPI_TIMEOUT		5000 /* ms */
 #define INTEL_SPI_FIFO_SZ		64
@@ -131,7 +131,6 @@
  * @sregs: Start of software sequencer registers
  * @nregions: Maximum number of regions
  * @pr_num: Maximum number of protected range registers
- * @writeable: Is the chip writeable
  * @locked: Is SPI setting locked
  * @swseq_reg: Use SW sequencer in register reads/writes
  * @swseq_erase: Use SW sequencer in erase operation
@@ -149,7 +148,6 @@
 	void __iomem *sregs;
 	size_t nregions;
 	size_t pr_num;
-	bool writeable;
 	bool locked;
 	bool swseq_reg;
 	bool swseq_erase;
@@ -304,6 +302,14 @@
 				  INTEL_SPI_TIMEOUT * 1000);
 }
 
+static bool intel_spi_set_writeable(struct intel_spi *ispi)
+{
+	if (!ispi->info->set_writeable)
+		return false;
+
+	return ispi->info->set_writeable(ispi->base, ispi->info->data);
+}
+
 static int intel_spi_init(struct intel_spi *ispi)
 {
 	u32 opmenu0, opmenu1, lvscc, uvscc, val;
@@ -316,19 +322,6 @@
 		ispi->nregions = BYT_FREG_NUM;
 		ispi->pr_num = BYT_PR_NUM;
 		ispi->swseq_reg = true;
-
-		if (writeable) {
-			/* Disable write protection */
-			val = readl(ispi->base + BYT_BCR);
-			if (!(val & BYT_BCR_WPD)) {
-				val |= BYT_BCR_WPD;
-				writel(val, ispi->base + BYT_BCR);
-				val = readl(ispi->base + BYT_BCR);
-			}
-
-			ispi->writeable = !!(val & BYT_BCR_WPD);
-		}
-
 		break;
 
 	case INTEL_SPI_LPT:
@@ -358,6 +351,12 @@
 		return -EINVAL;
 	}
 
+	/* Try to disable write protection if user asked to do so */
+	if (writeable && !intel_spi_set_writeable(ispi)) {
+		dev_warn(ispi->dev, "can't disable chip write protection\n");
+		writeable = false;
+	}
+
 	/* Disable #SMI generation from HW sequencer */
 	val = readl(ispi->base + HSFSTS_CTL);
 	val &= ~HSFSTS_CTL_FSMIE;
@@ -884,9 +883,12 @@
 		/*
 		 * If any of the regions have protection bits set, make the
 		 * whole partition read-only to be on the safe side.
+		 *
+		 * Also if the user did not ask the chip to be writeable
+		 * mask the bit too.
 		 */
-		if (intel_spi_is_protected(ispi, base, limit))
-			ispi->writeable = false;
+		if (!writeable || intel_spi_is_protected(ispi, base, limit))
+			part->mask_flags |= MTD_WRITEABLE;
 
 		end = (limit << 12) + 4096;
 		if (end > part->size)
@@ -927,7 +929,6 @@
 
 	ispi->dev = dev;
 	ispi->info = info;
-	ispi->writeable = info->writeable;
 
 	ret = intel_spi_init(ispi);
 	if (ret)
@@ -945,10 +946,6 @@
 
 	intel_spi_fill_partition(ispi, &part);
 
-	/* Prevent writes if not explicitly enabled */
-	if (!ispi->writeable || !writeable)
-		ispi->nor.mtd.flags &= ~MTD_WRITEABLE;
-
 	ret = mtd_device_register(&ispi->nor.mtd, &part, 1);
 	if (ret)
 		return ERR_PTR(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/core.c
@@ -177,7 +177,7 @@
 
 static int spi_nor_controller_ops_erase(struct spi_nor *nor, loff_t offs)
 {
-	if (spi_nor_protocol_is_dtr(nor->write_proto))
+	if (spi_nor_protocol_is_dtr(nor->reg_proto))
 		return -EOPNOTSUPP;
 
 	return nor->controller_ops->erase(nor, offs);
@@ -276,7 +276,7 @@
 	if (spi_nor_spimem_bounce(nor, &op))
 		memcpy(nor->bouncebuf, buf, op.data.nbytes);
 
-	if (nor->dirmap.wdesc) {
+	if (nor->dirmap.wdesc && !(nor->info->flags & SST_WRITE)) {
 		nbytes = spi_mem_dirmap_write(nor->dirmap.wdesc, op.addr.val,
 					      op.data.nbytes, op.data.buf.out);
 	} else {
@@ -380,13 +380,15 @@
 int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
 {
 	int ret;
+	int len;
 
+	nor->isparallel ? (len = 2) : (len = 1);
 	if (nor->spimem) {
 		struct spi_mem_op op =
 			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDSR, 0),
 				   SPI_MEM_OP_NO_ADDR,
 				   SPI_MEM_OP_NO_DUMMY,
-				   SPI_MEM_OP_DATA_IN(1, sr, 0));
+				   SPI_MEM_OP_DATA_IN(len, sr, 0));
 
 		if (nor->reg_proto == SNOR_PROTO_8_8_8_DTR) {
 			op.addr.nbytes = nor->params->rdsr_addr_nbytes;
@@ -403,12 +405,15 @@
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
 		ret = spi_nor_controller_ops_read_reg(nor, SPINOR_OP_RDSR, sr,
-						      1);
+						      len);
 	}
 
 	if (ret)
 		dev_dbg(nor->dev, "error %d reading SR\n", ret);
 
+	if (nor->isparallel)
+		sr[0] |= sr[1];
+
 	return ret;
 }
 
@@ -424,13 +429,15 @@
 static int spi_nor_read_fsr(struct spi_nor *nor, u8 *fsr)
 {
 	int ret;
+	int len;
 
+	nor->isparallel ? (len = 2) : (len = 1);
 	if (nor->spimem) {
 		struct spi_mem_op op =
 			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDFSR, 0),
 				   SPI_MEM_OP_NO_ADDR,
 				   SPI_MEM_OP_NO_DUMMY,
-				   SPI_MEM_OP_DATA_IN(1, fsr, 0));
+				   SPI_MEM_OP_DATA_IN(len, fsr, 0));
 
 		if (nor->reg_proto == SNOR_PROTO_8_8_8_DTR) {
 			op.addr.nbytes = nor->params->rdsr_addr_nbytes;
@@ -447,12 +454,15 @@
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
 		ret = spi_nor_controller_ops_read_reg(nor, SPINOR_OP_RDFSR, fsr,
-						      1);
+						      len);
 	}
 
 	if (ret)
 		dev_dbg(nor->dev, "error %d reading FSR\n", ret);
 
+	if (nor->isparallel)
+		fsr[0] &= fsr[1];
+
 	return ret;
 }
 
@@ -567,19 +577,46 @@
 /**
  * spi_nor_write_ear() - Write Extended Address Register.
  * @nor:	pointer to 'struct spi_nor'.
- * @ear:	value to write to the Extended Address Register.
+ * @addr:	value to write to the Extended Address Register.
  *
  * Return: 0 on success, -errno otherwise.
  */
-int spi_nor_write_ear(struct spi_nor *nor, u8 ear)
+int spi_nor_write_ear(struct spi_nor *nor, u32 addr)
 {
+	u8 code = SPINOR_OP_WREAR;
+	u32 ear;
 	int ret;
+	struct mtd_info *mtd = &nor->mtd;
 
+	/* Wait until finished previous write command. */
+	if (spi_nor_wait_till_ready(nor))
+		return 1;
+
+	if (mtd->size <= (0x1000000) << nor->shift)
+		return 0;
+
+	addr = addr % (u32)mtd->size;
+	ear = addr >> 24;
+
+	if (!nor->isstacked && ear == nor->curbank)
+		return 0;
+
+	if (nor->isstacked && mtd->size <= 0x2000000)
+		return 0;
+
+	if (nor->jedec_id == CFI_MFR_AMD)
+		code = SPINOR_OP_BRWR;
+	if (nor->jedec_id == CFI_MFR_ST ||
+	    nor->jedec_id == CFI_MFR_MACRONIX ||
+	    nor->jedec_id == CFI_MFR_PMC) {
+		spi_nor_write_enable(nor);
+		code = SPINOR_OP_WREAR;
+	}
 	nor->bouncebuf[0] = ear;
 
 	if (nor->spimem) {
 		struct spi_mem_op op =
-			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WREAR, 0),
+			SPI_MEM_OP(SPI_MEM_OP_CMD(code, 0),
 				   SPI_MEM_OP_NO_ADDR,
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_DATA_OUT(1, nor->bouncebuf, 0));
@@ -588,12 +625,12 @@
 
 		ret = spi_mem_exec_op(nor->spimem, &op);
 	} else {
-		ret = spi_nor_controller_ops_write_reg(nor, SPINOR_OP_WREAR,
-						       nor->bouncebuf, 1);
+		ret = spi_nor_controller_ops_write_reg(nor, code, nor->bouncebuf, 1);
+		if (ret < 0)
+			return ret;
 	}
 
-	if (ret)
-		dev_dbg(nor->dev, "error %d writing EAR\n", ret);
+	nor->curbank = ear;
 
 	return ret;
 }
@@ -632,6 +669,49 @@
 }
 
 /**
+ * read_ear - Get the extended/bank address register value
+ * @nor:	Pointer to the flash control structure
+ *
+ * This routine reads the Extended/bank address register value
+ *
+ * Return:	Negative if error occurred.
+ */
+static int read_ear(struct spi_nor *nor, struct flash_info *info)
+{
+	int ret;
+	u8 code;
+
+	/* This is actually Spansion */
+	if (nor->jedec_id == CFI_MFR_AMD)
+		code = SPINOR_OP_BRRD;
+	/* This is actually Micron */
+	else if (nor->jedec_id == CFI_MFR_ST ||
+		 nor->jedec_id == CFI_MFR_MACRONIX ||
+		 nor->jedec_id == CFI_MFR_PMC)
+		code = SPINOR_OP_RDEAR;
+	else
+		return -EINVAL;
+	if (nor->spimem) {
+		struct spi_mem_op op =
+			SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
+				   SPI_MEM_OP_NO_ADDR,
+				   SPI_MEM_OP_NO_DUMMY,
+				   SPI_MEM_OP_DATA_IN(1, nor->bouncebuf, 1));
+
+		ret = spi_mem_exec_op(nor->spimem, &op);
+	} else {
+		ret = nor->controller_ops->read_reg(nor, code, nor->bouncebuf, 1);
+	}
+	if (ret < 0) {
+		pr_err("error %d reading EAR\n", ret);
+		return ret;
+	}
+
+	return nor->bouncebuf[0];
+}
+
+
+/**
  * spi_nor_xsr_ready() - Query the Status Register of the S3AN flash to see if
  * the flash is ready for new commands.
  * @nor:	pointer to 'struct spi_nor'.
@@ -980,21 +1060,22 @@
 		ret = spi_nor_read_cr(nor, &sr_cr[1]);
 		if (ret)
 			return ret;
-	} else if (nor->params->quad_enable) {
+	} else if (spi_nor_get_protocol_width(nor->read_proto) == 4 &&
+		   spi_nor_get_protocol_width(nor->write_proto) == 4 &&
+		   nor->params->quad_enable) {
 		/*
 		 * If the Status Register 2 Read command (35h) is not
 		 * supported, we should at least be sure we don't
 		 * change the value of the SR2 Quad Enable bit.
 		 *
-		 * We can safely assume that when the Quad Enable method is
-		 * set, the value of the QE bit is one, as a consequence of the
-		 * nor->params->quad_enable() call.
+		 * When the Quad Enable method is set and the buswidth is 4, we
+		 * can safely assume that the value of the QE bit is one, as a
+		 * consequence of the nor->params->quad_enable() call.
 		 *
-		 * We can safely assume that the Quad Enable bit is present in
-		 * the Status Register 2 at BIT(1). According to the JESD216
-		 * revB standard, BFPT DWORDS[15], bits 22:20, the 16-bit
-		 * Write Status (01h) command is available just for the cases
-		 * in which the QE bit is described in SR2 at BIT(1).
+		 * According to the JESD216 revB standard, BFPT DWORDS[15],
+		 * bits 22:20, the 16-bit Write Status (01h) command is
+		 * available just for the cases in which the QE bit is
+		 * described in SR2 at BIT(1).
 		 */
 		sr_cr[1] = SR2_QUAD_EN_BIT1;
 	} else {
@@ -1007,6 +1088,15 @@
 	if (ret)
 		return ret;
 
+	ret = spi_nor_read_sr(nor, sr_cr);
+	if (ret)
+		return ret;
+
+	if (sr1 != sr_cr[0]) {
+		dev_dbg(nor->dev, "SR: Read back test failed\n");
+		return -EIO;
+	}
+
 	if (nor->flags & SNOR_F_NO_READ_CR)
 		return 0;
 
@@ -1185,10 +1275,24 @@
 				   SPI_MEM_OP_NO_ADDR,
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
+		if (nor->isstacked)
+			nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
 
-		spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
 
 		ret = spi_mem_exec_op(nor->spimem, &op);
+		if (ret)
+			return ret;
+
+		if (nor->isstacked) {
+			/* Wait until previous write command finished */
+			ret = spi_nor_wait_till_ready(nor);
+			if (ret)
+				return ret;
+			nor->spimem->spi->master->flags |= SPI_MASTER_U_PAGE;
+			ret = spi_mem_exec_op(nor->spimem, &op);
+			nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+		}
 	} else {
 		ret = spi_nor_controller_ops_write_reg(nor,
 						       SPINOR_OP_CHIP_ERASE,
@@ -1267,6 +1371,21 @@
 
 static void spi_nor_set_4byte_opcodes(struct spi_nor *nor)
 {
+	u32 sector_size = nor->info->sector_size;
+
+	/* Do some manufacturer fixups first */
+	switch (nor->jedec_id) {
+	case CFI_MFR_AMD:
+		/* No small sector erase for 4-byte command set */
+		nor->erase_opcode = SPINOR_OP_SE;
+		if (nor->isparallel)
+			sector_size <<= 1;
+
+		nor->mtd.erasesize = sector_size;
+		break;
+	default:
+		break;
+	}
 	nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
 	nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
 	nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
@@ -1331,7 +1450,7 @@
 				   SPI_MEM_OP_NO_DUMMY,
 				   SPI_MEM_OP_NO_DATA);
 
-		spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
+		spi_nor_spimem_setup_op(nor, &op, nor->reg_proto);
 
 		return spi_mem_exec_op(nor->spimem, &op);
 	} else if (nor->controller_ops->erase) {
@@ -1400,6 +1519,8 @@
 			continue;
 
 		erase = &map->erase_type[i];
+		if (!erase->size)
+			continue;
 
 		/* Alignment is not mandatory for overlaid regions */
 		if (region->offset & SNOR_OVERLAID_REGION &&
@@ -1644,7 +1765,7 @@
 static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
-	u32 addr, len;
+	u32 addr, len, offset;
 	uint32_t rem;
 	int ret;
 
@@ -1664,6 +1785,8 @@
 	if (ret)
 		return ret;
 
+	reinit_completion(&nor->spimem->request_completion);
+
 	/* whole-chip erase? */
 	if (len == mtd->size && !(nor->flags & SNOR_F_NO_OP_CHIP_ERASE)) {
 		unsigned long timeout;
@@ -1700,8 +1823,33 @@
 			ret = spi_nor_write_enable(nor);
 			if (ret)
 				goto erase_err;
+			offset = addr;
+			if (nor->isparallel == 1)
+				offset /= 2;
+			if (nor->isstacked == 1) {
+				if (offset >= (mtd->size / 2)) {
+					offset = offset - (mtd->size / 2);
+					nor->spimem->spi->master->flags |=
+						SPI_MASTER_U_PAGE;
+				} else {
+					nor->spimem->spi->master->flags &=
+						~SPI_MASTER_U_PAGE;
+				}
+			}
+			if (nor->addr_width == 3) {
+				/* Update Extended Address Register */
+				ret = spi_nor_write_ear(nor, offset);
+				if (ret)
+					goto erase_err;
+			}
+			ret = spi_nor_wait_till_ready(nor);
+			if (ret)
+				goto erase_err;
 
-			ret = spi_nor_erase_sector(nor, addr);
+			ret = spi_nor_write_enable(nor);
+			if (ret)
+				goto erase_err;
+			ret = spi_nor_erase_sector(nor, offset);
 			if (ret)
 				goto erase_err;
 
@@ -1723,6 +1871,8 @@
 	ret = spi_nor_write_disable(nor);
 
 erase_err:
+	complete(&nor->spimem->request_completion);
+
 	spi_nor_unlock_and_unprep(nor);
 
 	return ret;
@@ -1887,6 +2037,9 @@
 		return ERR_PTR(ret);
 	}
 
+	for (i = 0; i < SPI_NOR_MAX_ID_LEN; i++)
+		nor->spimem->device_id[i] = id[i];
+
 	for (i = 0; i < ARRAY_SIZE(manufacturers); i++) {
 		info = spi_nor_search_part_by_id(manufacturers[i]->parts,
 						 manufacturers[i]->nparts,
@@ -1907,19 +2060,107 @@
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
 	ssize_t ret;
+	u32 offset = from;
+	u32 stack_shift = 0;
+	u32 read_len = 0;
+	u32 rem_bank_len = 0;
+	u8 bank;
+	u8 cur_bank;
+	u8 nxt_bank;
+	u32 bank_size;
 
+#define OFFSET_16_MB 0x1000000
 	dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
+	if (nor->isparallel && (from & 1)) {
+		u8 two[2];
+		size_t local_retlen;
 
+		ret = spi_nor_read(mtd, (from & ~1), 2, &local_retlen, two);
+		if (ret < 0)
+			return ret;
+		buf[0] = two[1]; /* copy odd byte to buffer */
+		++buf;
+		*retlen += 1; /* We've read only one actual byte */
+		--len;
+		++from;
+	}
 	ret = spi_nor_lock_and_prep(nor);
 	if (ret)
 		return ret;
 
+	reinit_completion(&nor->spimem->request_completion);
+
 	while (len) {
-		loff_t addr = from;
+		if (nor->addr_width == 3) {
+			bank = (u32)from / (OFFSET_16_MB << nor->shift);
+			rem_bank_len = ((OFFSET_16_MB << nor->shift) *
+							(bank + 1)) - from;
+		}
+		offset = from;
+		if (nor->isparallel == 1)
+			offset /= 2;
+		if (nor->isstacked == 1) {
+			stack_shift = 1;
+			if (offset >= (mtd->size / 2)) {
+				offset = offset - (mtd->size / 2);
+				nor->spimem->spi->master->flags |=
+					SPI_MASTER_U_PAGE;
+			} else {
+				nor->spimem->spi->master->flags &=
+					~SPI_MASTER_U_PAGE;
+			}
+		}
+		if (nor->addr_width == 4) {
+			/*
+			 * Some flash devices like N25Q512 have multiple dies
+			 * in it. Read operation in these devices is bounded
+			 * by its die segment. In a continuous read, across
+			 * multiple dies, when the last byte of the selected
+			 * die segment is read, the next byte read is the
+			 * first byte of the same die segment. This is Die
+			 * cross over issue. So to handle this issue, split
+			 * a read transaction, that spans across multiple
+			 * banks, into one read per bank. Bank size is 16MB
+			 * for single and dual stacked mode and 32MB for dual
+			 * parallel mode.
+			 */
+			if (nor->spi && nor->spi->multi_die) {
+				bank_size = (OFFSET_16_MB << nor->shift);
+				cur_bank = offset / bank_size;
+				nxt_bank = (offset + len) / bank_size;
+				if (cur_bank != nxt_bank)
+					rem_bank_len = ((bank_size *
+							(cur_bank + 1)) -
+							offset) << nor->shift;
+				else
+					rem_bank_len = (mtd->size >>
+							stack_shift) -
+							(offset << nor->shift);
+			} else {
+				rem_bank_len = (mtd->size >> stack_shift) -
+						(offset << nor->shift);
+			}
+		}
+		if (nor->addr_width == 3) {
+			ret = spi_nor_write_ear(nor, offset);
+			if (ret) {
+				dev_err(nor->dev, "While writing ear register\n");
+				goto read_err;
+			}
+		}
+		if (len < rem_bank_len)
+			read_len = len;
+		else
+			read_len = rem_bank_len;
 
-		addr = spi_nor_convert_addr(nor, addr);
+		/* Wait till previous write/erase is done. */
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			goto read_err;
+
+		offset = spi_nor_convert_addr(nor, offset);
 
-		ret = spi_nor_read_data(nor, addr, len, buf);
+		ret = spi_nor_read_data(nor, (offset), read_len, buf);
 		if (ret == 0) {
 			/* We shouldn't see 0-length reads */
 			ret = -EIO;
@@ -1937,6 +2178,7 @@
 	ret = 0;
 
 read_err:
+	complete(&nor->spimem->request_completion);
 	spi_nor_unlock_and_unprep(nor);
 	return ret;
 }
@@ -1952,17 +2194,45 @@
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
 	size_t page_offset, page_remain, i;
 	ssize_t ret;
+	u32 offset, stack_shift = 0;
+	u8 bank = 0;
+	u32 rem_bank_len = 0;
 
+#define OFFSET_16_MB 0x1000000
 	dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+	/*
+	 * Cannot write to odd offset in parallel mode,
+	 * so write 2 bytes first
+	 */
+	if (nor->isparallel && (to & 1)) {
+		u8 two[2] = {0xff, buf[0]};
+		size_t local_retlen;
+
+		ret = spi_nor_write(mtd, to & ~1, 2, &local_retlen, two);
+		if (ret < 0)
+			return ret;
+
+		*retlen += 1; /* We've written only one actual byte */
+		++buf;
+		--len;
+		++to;
+	}
 
 	ret = spi_nor_lock_and_prep(nor);
 	if (ret)
 		return ret;
 
+	reinit_completion(&nor->spimem->request_completion);
+
 	for (i = 0; i < len; ) {
 		ssize_t written;
 		loff_t addr = to + i;
 
+		if (nor->addr_width == 3) {
+			bank = (u32)to / (OFFSET_16_MB << nor->shift);
+			rem_bank_len = ((OFFSET_16_MB << nor->shift) *
+							(bank + 1)) - to;
+		}
 		/*
 		 * If page_size is a power of two, the offset can be quickly
 		 * calculated with an AND operation. On the other cases we
@@ -1975,17 +2245,62 @@
 
 			page_offset = do_div(aux, nor->page_size);
 		}
-		/* the size of data remaining on the first page */
-		page_remain = min_t(size_t,
-				    nor->page_size - page_offset, len - i);
+		offset = (to + i);
+		if (nor->isparallel == 1)
+			offset /= 2;
+
+		if (nor->isstacked == 1) {
+			stack_shift = 1;
+			if (offset >= (mtd->size / 2)) {
+				offset = offset - (mtd->size / 2);
+				nor->spimem->spi->master->flags |=
+					SPI_MASTER_U_PAGE;
+			} else {
+				nor->spimem->spi->master->flags &=
+					~SPI_MASTER_U_PAGE;
+			}
+		}
 
-		addr = spi_nor_convert_addr(nor, addr);
+		/* Die cross over issue is not handled */
+		if (nor->addr_width == 4)
+			rem_bank_len = (mtd->size >> stack_shift) - offset;
+		if (nor->addr_width == 3) {
+			ret = spi_nor_write_ear(nor, offset);
+			if (ret) {
+				dev_err(nor->dev, "While writing ear register\n");
+				goto write_err;
+			}
+		}
+		if (nor->isstacked == 1) {
+			if ((len - i) <= rem_bank_len) {
+				page_remain = min_t(size_t,
+						    nor->page_size -
+						    page_offset, len - i);
+			} else {
+				/*
+				 * the size of data remaining
+				 * on the first page
+				 */
+				page_remain = min_t(size_t,
+						    nor->page_size -
+						    page_offset, rem_bank_len);
+			}
+		} else {
+			page_remain = min_t(size_t,
+					    nor->page_size -
+					    page_offset, len - i);
+		}
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			goto write_err;
+
+		offset = spi_nor_convert_addr(nor, offset);
 
 		ret = spi_nor_write_enable(nor);
 		if (ret)
 			goto write_err;
 
-		ret = spi_nor_write_data(nor, addr, page_remain, buf + i);
+		ret = spi_nor_write_data(nor, (offset), page_remain, buf + i);
 		if (ret < 0)
 			goto write_err;
 		written = ret;
@@ -1995,9 +2310,17 @@
 			goto write_err;
 		*retlen += written;
 		i += written;
+		if (written != page_remain) {
+			dev_err(nor->dev,
+				"While writing %zu bytes written %zd bytes\n",
+				page_remain, written);
+			ret = -EIO;
+			goto write_err;
+		}
 	}
 
 write_err:
+	complete(&nor->spimem->request_completion);
 	spi_nor_unlock_and_unprep(nor);
 	return ret;
 }
@@ -2146,7 +2469,8 @@
 	spi_nor_spimem_setup_op(nor, &op, read->proto);
 
 	/* convert the dummy cycles to the number of bytes */
-	op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+	op.dummy.nbytes = (read->num_mode_clocks + read->num_wait_states) *
+			  op.dummy.buswidth / 8;
 	if (spi_nor_protocol_is_dtr(nor->read_proto))
 		op.dummy.nbytes *= 2;
 
@@ -2230,11 +2554,20 @@
 	erase->size = size;
 	erase->opcode = opcode;
 	/* JEDEC JESD216B Standard imposes erase sizes to be power of 2. */
-	erase->size_shift = ffs(erase->size) - 1;
+	erase->size_shift = erase->size ? (ffs(erase->size) - 1) : 0;
 	erase->size_mask = (1 << erase->size_shift) - 1;
 }
 
 /**
+ * spi_nor_mask_erase_type() - mask out a SPI NOR erase type
+ * @erase:	pointer to a structure that describes a SPI NOR erase type
+ */
+void spi_nor_mask_erase_type(struct spi_nor_erase_type *erase)
+{
+	erase->size = 0;
+}
+
+/**
  * spi_nor_init_uniform_erase_map() - Initialize uniform erase map
  * @map:		the erase map of the SPI NOR
  * @erase_mask:		bitmask encoding erase types that can erase the entire
@@ -2383,6 +2716,12 @@
 	u32 wanted_size = nor->info->sector_size;
 	int i;
 
+	if (nor->isparallel)
+		wanted_size <<= 1;
+
+	if (mtd->erasesize &&
+	    nor->jedec_id != CFI_MFR_AMD)
+		return 0;
 	/*
 	 * The previous implementation handling Sector Erase commands assumed
 	 * that the SPI flash memory has an uniform layout then used only one
@@ -2402,6 +2741,9 @@
 			return -EINVAL;
 		nor->erase_opcode = erase->opcode;
 		mtd->erasesize = erase->size;
+		if (nor->shift)
+			mtd->erasesize = mtd->erasesize << nor->shift;
+
 		return 0;
 	}
 
@@ -2541,6 +2883,9 @@
 	const struct flash_info *info = nor->info;
 	struct device_node *np = spi_nor_get_flash_node(nor);
 	u8 i, erase_mask;
+	u32 n_sectors = info->n_sectors;
+	u32 sector_size = info->sector_size;
+	u32 page_size = info->page_size;
 
 	/* Initialize default flash parameters and settings. */
 	params->quad_enable = spi_nor_sr2_bit1_quad_enable;
@@ -2553,8 +2898,16 @@
 
 	/* Set SPI NOR sizes. */
 	params->writesize = 1;
-	params->size = (u64)info->sector_size * info->n_sectors;
-	params->page_size = info->page_size;
+	if (nor->isstacked)
+		n_sectors <<= 1;
+
+	if (nor->isparallel) {
+		sector_size <<= 1;
+		page_size <<= 1;
+	}
+
+	params->size = (u64)sector_size * n_sectors;
+	params->page_size = page_size;
 
 	if (!(info->flags & SPI_NOR_NO_FR)) {
 		/* Default to Fast Read for DT and non-DT platform devices. */
@@ -2637,7 +2990,7 @@
 		i++;
 	}
 	erase_mask |= BIT(i);
-	spi_nor_set_erase_type(&map->erase_type[i], info->sector_size,
+	spi_nor_set_erase_type(&map->erase_type[i], sector_size,
 			       SPINOR_OP_SE);
 	spi_nor_init_uniform_erase_map(map, erase_mask, params->size);
 }
@@ -2758,10 +3111,21 @@
 	if (!(nor->flags & SNOR_F_IO_MODE_EN_VOLATILE))
 		return 0;
 
+	if (nor->isstacked)
+		nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+
 	ret = nor->params->octal_dtr_enable(nor, enable);
 	if (ret)
 		return ret;
 
+	if (nor->isstacked) {
+		nor->spimem->spi->master->flags |= SPI_MASTER_U_PAGE;
+		ret = nor->params->octal_dtr_enable(nor, enable);
+		nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+		if (ret)
+			return ret;
+	}
+
 	if (enable)
 		nor->reg_proto = SNOR_PROTO_8_8_8_DTR;
 	else
@@ -2778,6 +3142,8 @@
  */
 static int spi_nor_quad_enable(struct spi_nor *nor)
 {
+	int err;
+
 	if (!nor->params->quad_enable)
 		return 0;
 
@@ -2785,13 +3151,28 @@
 	      spi_nor_get_protocol_width(nor->write_proto) == 4))
 		return 0;
 
-	return nor->params->quad_enable(nor);
+	err = nor->params->quad_enable(nor);
+	if (nor->isstacked) {
+		nor->spimem->spi->master->flags |= SPI_MASTER_U_PAGE;
+		err = nor->params->quad_enable(nor);
+		nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+	}
+	return err;
 }
 
 static int spi_nor_init(struct spi_nor *nor)
 {
 	int err;
 
+	if (nor->jedec_id == CFI_MFR_ATMEL ||
+	    nor->jedec_id == CFI_MFR_INTEL ||
+	    nor->jedec_id == CFI_MFR_SST ||
+	    nor->flags & SNOR_F_HAS_LOCK) {
+		spi_nor_write_enable(nor);
+		nor->bouncebuf[0] = 0;
+		spi_nor_write_sr(nor, nor->bouncebuf, 1);
+	}
+
 	err = spi_nor_octal_dtr_enable(nor, true);
 	if (err) {
 		dev_dbg(nor->dev, "octal mode not supported\n");
@@ -2832,6 +3213,11 @@
 		WARN_ONCE(nor->flags & SNOR_F_BROKEN_RESET,
 			  "enabling reset hack; may not recover from unexpected reboots\n");
 		nor->params->set_4byte_addr_mode(nor, true);
+		if (nor->isstacked) {
+			nor->spimem->spi->master->flags |= SPI_MASTER_U_PAGE;
+			nor->params->set_4byte_addr_mode(nor, true);
+			nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+		}
 	}
 
 	return 0;
@@ -2952,8 +3338,10 @@
 void spi_nor_restore(struct spi_nor *nor)
 {
 	/* restore the addressing mode */
-	if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
-	    nor->flags & SNOR_F_BROKEN_RESET)
+	if (nor->addr_width == 4 && !(nor->info->flags & SNOR_F_4B_OPCODES) &&
+	    (nor->flags & SNOR_F_BROKEN_RESET) &&
+	    (nor->jedec_id != CFI_MFR_AMD) &&
+	    !(nor->info->flags & SPI_NOR_4B_OPCODES))
 		nor->params->set_4byte_addr_mode(nor, false);
 
 	if (nor->flags & SNOR_F_SOFT_RESET)
@@ -2980,6 +3368,8 @@
 
 static int spi_nor_set_addr_width(struct spi_nor *nor)
 {
+	struct device_node *np = spi_nor_get_flash_node(nor);
+	struct device_node *np_spi;
 	if (nor->addr_width) {
 		/* already configured from SFDP */
 	} else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) {
@@ -3003,8 +3393,65 @@
 	}
 
 	if (nor->addr_width == 3 && nor->mtd.size > 0x1000000) {
-		/* enable 4-byte addressing if the device exceeds 16MiB */
-		nor->addr_width = 4;
+#ifdef CONFIG_OF
+		np_spi = of_get_next_parent(np);
+		if (of_property_match_string(np_spi, "compatible",
+					     "xlnx,zynq-qspi-1.0") >= 0) {
+			int status;
+
+			nor->addr_width = 3;
+			nor->params->set_4byte_addr_mode(nor, false);
+			if (nor->isstacked) {
+				nor->spimem->spi->master->flags |=
+					SPI_MASTER_U_PAGE;
+				nor->params->set_4byte_addr_mode(nor, false);
+				nor->spimem->spi->master->flags &=
+					~SPI_MASTER_U_PAGE;
+			}
+			status = read_ear(nor, (struct flash_info *)nor->info);
+			if (status < 0)
+				dev_warn(nor->dev, "failed to read ear reg\n");
+			else
+				nor->curbank = status & EAR_SEGMENT_MASK;
+		} else {
+#endif
+			/*
+			 * enable 4-byte addressing if the
+			 * device exceeds 16MiB
+			 */
+			nor->addr_width = 4;
+			if (nor->jedec_id == CFI_MFR_AMD ||
+			    nor->info->flags & SPI_NOR_4B_OPCODES) {
+				spi_nor_set_4byte_opcodes(nor);
+				nor->params->set_4byte_addr_mode(nor, true);
+				if (nor->isstacked) {
+					nor->spimem->spi->master->flags |=
+					SPI_MASTER_U_PAGE;
+					nor->params->set_4byte_addr_mode(nor, true);
+					nor->spimem->spi->master->flags &=
+					~SPI_MASTER_U_PAGE;
+				}
+			} else {
+				np_spi = of_get_next_parent(np);
+				if (of_property_match_string(np_spi,
+							     "compatible",
+							     "xlnx,xps-spi-2.00.a") >= 0) {
+					nor->addr_width = 3;
+					nor->params->set_4byte_addr_mode(nor, false);
+				} else {
+					nor->params->set_4byte_addr_mode(nor, true);
+					if (nor->isstacked) {
+						nor->spimem->spi->master->flags |=
+							SPI_MASTER_U_PAGE;
+						nor->params->set_4byte_addr_mode(nor, true);
+						nor->spimem->spi->master->flags &=
+							~SPI_MASTER_U_PAGE;
+					}
+				}
+			}
+#ifdef CONFIG_OF
+		}
+#endif
 	}
 
 	if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
@@ -3074,12 +3521,14 @@
 int spi_nor_scan(struct spi_nor *nor, const char *name,
 		 const struct spi_nor_hwcaps *hwcaps)
 {
-	const struct flash_info *info;
+	const struct flash_info *info = NULL;
 	struct device *dev = nor->dev;
 	struct mtd_info *mtd = &nor->mtd;
 	struct device_node *np = spi_nor_get_flash_node(nor);
 	int ret;
 	int i;
+	struct device_node *np_spi;
+	u32 is_dual;
 
 	ret = spi_nor_check(nor);
 	if (ret)
@@ -3125,7 +3574,11 @@
 	if (info->flags & SPI_NOR_HAS_LOCK)
 		nor->flags |= SNOR_F_HAS_LOCK;
 
-	mtd->_write = spi_nor_write;
+	/* sst nor chips use AAI word program */
+	if (info->flags & SST_WRITE)
+		mtd->_write = sst_write;
+	else
+		mtd->_write = spi_nor_write;
 
 	/* Init flash parameters based on flash_info struct and SFDP */
 	ret = spi_nor_init_params(nor);
@@ -3139,8 +3592,73 @@
 	mtd->writesize = nor->params->writesize;
 	mtd->flags = MTD_CAP_NORFLASH;
 	mtd->size = nor->params->size;
-	mtd->_erase = spi_nor_erase;
 	mtd->_read = spi_nor_read;
+	nor->page_size = nor->params->page_size;
+#ifdef CONFIG_OF
+	np_spi = of_get_next_parent(np);
+	if (((of_property_match_string(np_spi, "compatible",
+				       "xlnx,zynq-qspi-1.0") >= 0) ||
+		(of_property_match_string(np_spi, "compatible",
+				"xlnx,zynqmp-qspi-1.0") >= 0)) ||
+		(of_property_match_string(np_spi, "compatible",
+				"xlnx,versal-qspi-1.0") >= 0) ||
+		(of_property_match_string(np_spi, "compatible",
+				"xlnx,versal-ospi-1.0") >= 0)) {
+		if (of_property_read_u32(np_spi, "is-dual",
+					 &is_dual) < 0) {
+			/* Default to single if prop not defined */
+			nor->shift = 0;
+			nor->isstacked = 0;
+			nor->isparallel = 0;
+		} else {
+			if (is_dual == 1) {
+				/* dual parallel */
+				nor->shift = 1;
+				nor->page_size = info->page_size << nor->shift;
+				mtd->size <<= nor->shift;
+				nor->isparallel = 1;
+				nor->isstacked = 0;
+				nor->spi->master->flags |=
+						(SPI_MASTER_DATA_STRIPE
+						| SPI_MASTER_BOTH_CS);
+			} else {
+#ifdef CONFIG_SPI_ZYNQ_QSPI_DUAL_STACKED
+				/* dual stacked */
+				nor->shift = 0;
+				mtd->size <<= 1;
+				nor->isstacked = 1;
+				nor->isparallel = 0;
+#else
+				u32 is_stacked;
+
+				if (of_property_read_u32(np_spi,
+							 "is-stacked",
+							 &is_stacked) < 0) {
+					is_stacked = 0;
+				}
+				if (is_stacked) {
+					/* dual stacked */
+					nor->shift = 0;
+					mtd->size <<= 1;
+					nor->isstacked = 1;
+					nor->isparallel = 0;
+				} else {
+					/* single */
+					nor->shift = 0;
+					nor->isstacked = 0;
+					nor->isparallel = 0;
+				}
+#endif
+			}
+		}
+	}
+#else
+	/* Default to single */
+	nor->shift = 0;
+	nor->isstacked = 0;
+	nor->isparallel = 0;
+#endif
+
 	mtd->_suspend = spi_nor_suspend;
 	mtd->_resume = spi_nor_resume;
 	mtd->_get_device = spi_nor_get_device;
@@ -3165,13 +3683,17 @@
 		nor->flags |= SNOR_F_HAS_4BIT_BP;
 		if (info->flags & SPI_NOR_BP3_SR_BIT6)
 			nor->flags |= SNOR_F_HAS_SR_BP3_BIT6;
+		else if (info->flags & SPI_NOR_BP3_SR_BIT5)
+			nor->flags |= SNOR_F_HAS_SR_BP3_BIT5;
 	}
 
 	if (info->flags & SPI_NOR_NO_ERASE)
 		mtd->flags |= MTD_NO_ERASE;
+	else
+		mtd->_erase = spi_nor_erase;
 
 	mtd->dev.parent = dev;
-	nor->page_size = nor->params->page_size;
+	nor->jedec_id = info->id[0];
 	mtd->writebufsize = nor->page_size;
 
 	if (of_property_read_bool(np, "broken-flash-reset"))
@@ -3311,8 +3833,12 @@
 	nor->dev = &spi->dev;
 	spi_nor_set_flash_node(nor, spi->dev.of_node);
 
+	if (nor->spimem)
+		init_completion(&nor->spimem->request_completion);
+
 	spi_mem_set_drvdata(spimem, nor);
 
+	nor->spi = spi;
 	if (data && data->name)
 		nor->mtd.name = data->name;
 
@@ -3377,6 +3903,9 @@
 {
 	struct spi_nor *nor = spi_mem_get_drvdata(spimem);
 
+	if (nor->addr_width == 3 &&
+	    (nor->mtd.size >> nor->shift) > 0x1000000)
+		spi_nor_write_ear(nor, 0);
 	spi_nor_restore(nor);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/core.h
@@ -29,6 +29,7 @@
 	SNOR_F_IO_MODE_EN_VOLATILE = BIT(14),
 	SNOR_F_SOFT_RESET	= BIT(15),
 	SNOR_F_SWP_IS_VOLATILE	= BIT(16),
+	SNOR_F_HAS_SR_BP3_BIT5  = BIT(17),
 };
 
 struct spi_nor_read_command {
@@ -382,6 +383,14 @@
 					 * protection bits. Usually these will
 					 * power-up in a write-protected state.
 					 */
+#define SST_GLOBAL_PROT_UNLK	BIT(24)	/* Unlock the Global protection for
+					 * sst flashes
+					 */
+#define SPI_NOR_BP3_SR_BIT5	BIT(25) /*
+					 * BP3 is bit 5 of status register.
+					 * Must be used with SPI_NOR_4BIT_BP.
+					 */
+	int	(*quad_enable)(struct spi_nor *nor);
 
 	const struct spi_nor_otp_organization otp_org;
 
@@ -498,7 +507,7 @@
 int spi_nor_write_enable(struct spi_nor *nor);
 int spi_nor_write_disable(struct spi_nor *nor);
 int spi_nor_set_4byte_addr_mode(struct spi_nor *nor, bool enable);
-int spi_nor_write_ear(struct spi_nor *nor, u8 ear);
+int spi_nor_write_ear(struct spi_nor *nor, u32 addr);
 int spi_nor_wait_till_ready(struct spi_nor *nor);
 int spi_nor_global_block_unlock(struct spi_nor *nor);
 int spi_nor_lock_and_prep(struct spi_nor *nor);
@@ -538,6 +547,7 @@
 
 void spi_nor_set_erase_type(struct spi_nor_erase_type *erase, u32 size,
 			    u8 opcode);
+void spi_nor_mask_erase_type(struct spi_nor_erase_type *erase);
 struct spi_nor_erase_region *
 spi_nor_region_next(struct spi_nor_erase_region *region);
 void spi_nor_init_uniform_erase_map(struct spi_nor_erase_map *map,
@@ -557,4 +567,7 @@
 	return mtd->priv;
 }
 
+int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+	      size_t *retlen, const u_char *buf);
+
 #endif /* __LINUX_MTD_SPI_NOR_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/gigadevice.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/gigadevice.c
@@ -8,6 +8,136 @@
 
 #include "core.h"
 
+#define SPINOR_OP_GD_DTR_RD	0xfd	/* Fast Read opcode in DTR mode */
+#define SPINOR_OP_GD_RD_ANY_REG	0x85	/* Read volatile register */
+#define SPINOR_OP_GD_WR_ANY_REG	0x81	/* Write volatile register */
+#define SPINOR_REG_GD_CFR0V	0x00	/* For setting octal DTR mode */
+#define SPINOR_REG_GD_CFR1V	0x01	/* For setting dummy cycles */
+#define SPINOR_GD_OCT_DTR	0xe7	/* Enable Octal DTR. */
+#define SPINOR_GD_EXSPI		0xff	/* Enable Extended SPI (default) */
+
+static int spi_nor_gigadevice_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	int ret;
+
+	if (enable) {
+		/* Use 20 dummy cycles for memory array reads. */
+		ret = spi_nor_write_enable(nor);
+		if (ret)
+			return ret;
+
+		*buf = 20;
+		op = (struct spi_mem_op)
+			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_GD_WR_ANY_REG, 1),
+				   SPI_MEM_OP_ADDR(3, SPINOR_REG_GD_CFR1V, 1),
+				   SPI_MEM_OP_NO_DUMMY,
+				   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+		ret = spi_mem_exec_op(nor->spimem, &op);
+		if (ret)
+			return ret;
+
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			return ret;
+	}
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	if (enable)
+		*buf = SPINOR_GD_OCT_DTR;
+	else
+		*buf = SPINOR_GD_EXSPI;
+
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_GD_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(enable ? 3 : 4,
+					   SPINOR_REG_GD_CFR0V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (nor->isstacked &&
+	    !(nor->spimem->spi->master->flags & SPI_MASTER_U_PAGE))
+		return 0;
+
+	/* Read flash ID to make sure the switch was successful. */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDID, 1),
+			   SPI_MEM_OP_NO_ADDR,
+			   SPI_MEM_OP_DUMMY(enable ? 8 : 0, 1),
+			   SPI_MEM_OP_DATA_IN(round_up(nor->info->id_len, 2),
+					      buf, 1));
+
+	if (enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (memcmp(buf, nor->info->id, nor->info->id_len))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int gd25lx256e_set_4byte_addr_mode(struct spi_nor *nor, bool enable)
+{
+	int ret;
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	ret = spi_nor_set_4byte_addr_mode(nor, enable);
+	if (ret)
+		return ret;
+
+	return spi_nor_write_disable(nor);
+}
+
+static void gd25lx256e_default_init(struct spi_nor *nor)
+{
+	nor->params->octal_dtr_enable = spi_nor_gigadevice_octal_dtr_enable;
+	nor->params->set_4byte_addr_mode = gd25lx256e_set_4byte_addr_mode;
+}
+
+static void gd25lx256e_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/* Set the Fast Read settings. */
+	nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+	spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, 20, SPINOR_OP_GD_DTR_RD,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	nor->cmd_ext_type = SPI_NOR_EXT_REPEAT;
+	nor->params->rdsr_dummy = 8;
+	nor->params->rdsr_addr_nbytes = 0;
+
+	/*
+	 * The BFPT quad enable field is set to a reserved value so the quad
+	 * enable function is ignored by spi_nor_parse_bfpt(). Make sure we
+	 * disable it.
+	 */
+	nor->params->quad_enable = NULL;
+}
+
+static struct spi_nor_fixups gd25lx256e_fixups = {
+	.default_init = gd25lx256e_default_init,
+	.post_sfdp = gd25lx256e_post_sfdp_fixup,
+};
+
 static void gd25q256_default_init(struct spi_nor *nor)
 {
 	/*
@@ -50,6 +180,12 @@
 			   SPI_NOR_4B_OPCODES | SPI_NOR_HAS_LOCK |
 			   SPI_NOR_HAS_TB | SPI_NOR_TB_SR_BIT6)
 		.fixups = &gd25q256_fixups },
+	{ "gd25lx256e",  INFO(0xc86819, 0, 64 * 1024, 512,
+			      SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ |
+			      SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ |
+			      SPI_NOR_OCTAL_DTR_PP |
+			      SPI_NOR_IO_MODE_EN_VOLATILE)
+		.fixups = &gd25lx256e_fixups },
 };
 
 const struct spi_nor_manufacturer spi_nor_gigadevice = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/issi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/issi.c
@@ -8,6 +8,136 @@
 
 #include "core.h"
 
+#define SPINOR_OP_IS_DTR_RD	0xfd	/* Fast Read opcode in DTR mode */
+#define SPINOR_OP_IS_RD_ANY_REG	0x85	/* Read volatile register */
+#define SPINOR_OP_IS_WR_ANY_REG	0x81	/* Write volatile register */
+#define SPINOR_REG_IS_CFR0V	0x00	/* For setting octal DTR mode */
+#define SPINOR_REG_IS_CFR1V	0x01	/* For setting dummy cycles */
+#define SPINOR_IS_OCT_DTR	0xe7	/* Enable Octal DTR. */
+#define SPINOR_IS_EXSPI		0xff	/* Enable Extended SPI (default) */
+
+static int spi_nor_issi_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	int ret;
+
+	if (enable) {
+		/* Use 20 dummy cycles for memory array reads. */
+		ret = spi_nor_write_enable(nor);
+		if (ret)
+			return ret;
+
+		*buf = 20;
+		op = (struct spi_mem_op)
+			SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_IS_WR_ANY_REG, 1),
+				   SPI_MEM_OP_ADDR(3, SPINOR_REG_IS_CFR1V, 1),
+				   SPI_MEM_OP_NO_DUMMY,
+				   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+		ret = spi_mem_exec_op(nor->spimem, &op);
+		if (ret)
+			return ret;
+
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			return ret;
+	}
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	if (enable)
+		*buf = SPINOR_IS_OCT_DTR;
+	else
+		*buf = SPINOR_IS_EXSPI;
+
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_IS_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(enable ? 3 : 4,
+					   SPINOR_REG_IS_CFR0V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (nor->isstacked &&
+	    !(nor->spimem->spi->master->flags & SPI_MASTER_U_PAGE))
+		return 0;
+
+	/* Read flash ID to make sure the switch was successful. */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDID, 1),
+			   SPI_MEM_OP_NO_ADDR,
+			   SPI_MEM_OP_DUMMY(enable ? 8 : 0, 1),
+			   SPI_MEM_OP_DATA_IN(round_up(nor->info->id_len, 2),
+					      buf, 1));
+
+	if (enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (memcmp(buf, nor->info->id, nor->info->id_len))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int is25wx256_set_4byte_addr_mode(struct spi_nor *nor, bool enable)
+{
+	int ret;
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	ret = spi_nor_set_4byte_addr_mode(nor, enable);
+	if (ret)
+		return ret;
+
+	return spi_nor_write_disable(nor);
+}
+
+static void is25wx256_default_init(struct spi_nor *nor)
+{
+	nor->params->octal_dtr_enable = spi_nor_issi_octal_dtr_enable;
+	nor->params->set_4byte_addr_mode = is25wx256_set_4byte_addr_mode;
+}
+
+static void is25wx256_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/* Set the Fast Read settings. */
+	nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+	spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, 20, SPINOR_OP_IS_DTR_RD,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	nor->cmd_ext_type = SPI_NOR_EXT_REPEAT;
+	nor->params->rdsr_dummy = 8;
+	nor->params->rdsr_addr_nbytes = 0;
+
+	/*
+	 * The BFPT quad enable field is set to a reserved value so the quad
+	 * enable function is ignored by spi_nor_parse_bfpt(). Make sure we
+	 * disable it.
+	 */
+	nor->params->quad_enable = NULL;
+}
+
+static struct spi_nor_fixups is25wx256_fixups = {
+	.default_init = is25wx256_default_init,
+	.post_sfdp = is25wx256_post_sfdp_fixup,
+};
+
 static int
 is25lp256_post_bfpt_fixups(struct spi_nor *nor,
 			   const struct sfdp_parameter_header *bfpt_header,
@@ -31,33 +161,65 @@
 
 static const struct flash_info issi_parts[] = {
 	/* ISSI */
+	{ "is25wp080d", INFO(0x9d7014, 0, 64 * 1024, 32, SECT_4K |
+		SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK) },
+	{ "is25wp016d", INFO(0x9d7015, 0, 64 * 1024, 32, SECT_4K |
+		SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK) },
 	{ "is25cd512",  INFO(0x7f9d20, 0, 32 * 1024,   2, SECT_4K) },
 	{ "is25lq040b", INFO(0x9d4013, 0, 64 * 1024,   8,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "is25lp016d", INFO(0x9d6015, 0, 64 * 1024,  32,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "is25lp080d", INFO(0x9d6014, 0, 64 * 1024,  16,
-			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+			SPI_NOR_HAS_LOCK) },
 	{ "is25lp032",  INFO(0x9d6016, 0, 64 * 1024,  64,
-			     SECT_4K | SPI_NOR_DUAL_READ) },
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_HAS_LOCK) },
 	{ "is25lp064",  INFO(0x9d6017, 0, 64 * 1024, 128,
-			     SECT_4K | SPI_NOR_DUAL_READ) },
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_HAS_LOCK) },
 	{ "is25lp128",  INFO(0x9d6018, 0, 64 * 1024, 256,
-			     SECT_4K | SPI_NOR_DUAL_READ) },
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_HAS_LOCK) },
 	{ "is25lp256",  INFO(0x9d6019, 0, 64 * 1024, 512,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-			     SPI_NOR_4B_OPCODES)
+			SPI_NOR_4B_OPCODES | SPI_NOR_HAS_LOCK)
 		.fixups = &is25lp256_fixups },
+	{ "is25wp256d", INFO(0x9d7019, 0, 64 * 1024, 512,
+			SECT_4K | SPI_NOR_DUAL_READ |
+			SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK |
+			SPI_NOR_4B_OPCODES) },
 	{ "is25wp032",  INFO(0x9d7016, 0, 64 * 1024,  64,
-			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+			SPI_NOR_HAS_LOCK) },
 	{ "is25wp064",  INFO(0x9d7017, 0, 64 * 1024, 128,
-			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ
+			 | SPI_NOR_HAS_LOCK) },
 	{ "is25wp128",  INFO(0x9d7018, 0, 64 * 1024, 256,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "is25wp256", INFO(0x9d7019, 0, 64 * 1024, 512,
 			    SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			    SPI_NOR_4B_OPCODES)
 		.fixups = &is25lp256_fixups },
+	{ "is25lp512m", INFO(0x9d601a, 0, 64 * 1024, 1024,
+			SECT_4K | SPI_NOR_DUAL_READ |
+			SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK) },
+	{ "is25wp512m", INFO(0x9d701a, 0, 64 * 1024, 1024,
+			SECT_4K | SPI_NOR_DUAL_READ |
+			SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK |
+			SPI_NOR_4B_OPCODES) },
+	{ "is25lp01g", INFO(0x9d601b, 0, 64 * 1024, 2048,
+			SECT_4K | SPI_NOR_DUAL_READ |
+			SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK |
+			SPI_NOR_4B_OPCODES) },
+	{ "is25wp01g", INFO(0x9d701b, 0, 64 * 1024, 2048,
+			SECT_4K | SPI_NOR_DUAL_READ |
+			SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK |
+			SPI_NOR_4B_OPCODES) },
+	{ "is25wx256",  INFO(0x9d5b19, 0, 128 * 1024, 256,
+			     SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ |
+			     SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ |
+			     SPI_NOR_OCTAL_DTR_PP |
+			     SPI_NOR_IO_MODE_EN_VOLATILE)
+		.fixups = &is25wx256_fixups },
 
 	/* PMC */
 	{ "pm25lv512",   INFO(0,        0, 32 * 1024,    2, SECT_4K_PMC) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/macronix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/macronix.c
@@ -8,6 +8,134 @@
 
 #include "core.h"
 
+#define SPINOR_OP_MX_DTR_RD	0xee	/* Fast Read opcode in DTR mode */
+#define SPINOR_OP_MX_RD_ANY_REG	0x71	/* Read volatile register */
+#define SPINOR_OP_MX_WR_ANY_REG	0x72	/* Write volatile register */
+#define SPINOR_REG_MX_CFR0V	0x00	/* For setting octal DTR mode */
+#define SPINOR_MX_OCT_DTR	0x02	/* Enable Octal DTR. */
+#define SPINOR_MX_EXSPI		0x00	/* Enable Extended SPI (default) */
+
+static int spi_nor_macronix_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	int ret;
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	if (enable)
+		*buf = SPINOR_MX_OCT_DTR;
+	else
+		*buf = SPINOR_MX_EXSPI;
+
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_MX_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(4, SPINOR_REG_MX_CFR0V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+
+	if (!enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (nor->isstacked &&
+	    !(nor->spimem->spi->master->flags & SPI_MASTER_U_PAGE))
+		return 0;
+
+	/* Read flash ID to make sure the switch was successful. */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDID, 1),
+			   SPI_MEM_OP_ADDR(enable ? 4 : 0, 0, enable ? 1 : 0),
+			   SPI_MEM_OP_DUMMY(enable ? 4 : 0, 1),
+			   SPI_MEM_OP_DATA_IN(round_up(nor->info->id_len, 2),
+					      buf, 1));
+
+	if (enable)
+		spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (enable) {
+		if (memcmp(buf, nor->spimem->device_id, nor->info->id_len))
+			return -EINVAL;
+	} else {
+		if (memcmp(buf, nor->info->id, nor->info->id_len))
+			return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int mx25um51345g_set_4byte(struct spi_nor *nor, bool enable)
+{
+	(void)enable;
+
+	return 0;
+}
+
+static void mx25um51345g_default_init_fixups(struct spi_nor *nor)
+{
+	u8 id_byte1, id_byte2;
+	u32 sector_size = nor->info->sector_size;
+
+	nor->params->set_4byte_addr_mode = mx25um51345g_set_4byte;
+
+	/*
+	 * Macronix Read Id bytes are always output in STR mode. Since tuning
+	 * is based on Read Id command, adjust the Read Id bytes that will
+	 * match the Read Id output in DTR mode.
+	 */
+	id_byte1 = nor->spimem->device_id[1];
+	id_byte2 = nor->spimem->device_id[2];
+	nor->spimem->device_id[1] = nor->spimem->device_id[0];
+	nor->spimem->device_id[2] = id_byte1;
+	nor->spimem->device_id[3] = id_byte1;
+	nor->spimem->device_id[4] = id_byte2;
+	nor->spimem->device_id[5] = id_byte2;
+
+	if (nor->isparallel)
+		sector_size <<= 1;
+
+	spi_nor_set_erase_type(&nor->params->erase_map.erase_type[1],
+			       sector_size, SPINOR_OP_BE_4K_4B);
+	nor->params->page_programs[SNOR_CMD_PP_8_8_8_DTR].opcode =
+				SPINOR_OP_PP_4B;
+
+	nor->params->octal_dtr_enable = spi_nor_macronix_octal_dtr_enable;
+}
+
+static void mx25um51345g_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/* Set the Fast Read settings. */
+	nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+	spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, 20, SPINOR_OP_MX_DTR_RD,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	nor->cmd_ext_type = SPI_NOR_EXT_INVERT;
+	nor->params->rdsr_dummy = 8;
+	nor->params->rdsr_addr_nbytes = 0;
+
+	/*
+	 * The BFPT quad enable field is set to a reserved value so the quad
+	 * enable function is ignored by spi_nor_parse_bfpt(). Make sure we
+	 * disable it.
+	 */
+	nor->params->quad_enable = NULL;
+}
+
+static struct spi_nor_fixups mx25um51345g_fixups = {
+	.default_init = mx25um51345g_default_init_fixups,
+	.post_sfdp = mx25um51345g_post_sfdp_fixup,
+};
+
 static int
 mx25l25635_post_bfpt_fixups(struct spi_nor *nor,
 			    const struct sfdp_parameter_header *bfpt_header,
@@ -82,11 +210,19 @@
 	{ "mx66l1g45g",  INFO(0xc2201b, 0, 64 * 1024, 2048,
 			      SECT_4K | SPI_NOR_DUAL_READ |
 			      SPI_NOR_QUAD_READ) },
+	{ "mx66u1g45g",  INFO(0xc2253b, 0, 64 * 1024, 2048, SECT_4K |
+			SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "mx66l1g55g",  INFO(0xc2261b, 0, 64 * 1024, 2048,
 			      SPI_NOR_QUAD_READ) },
 	{ "mx66u2g45g",	 INFO(0xc2253c, 0, 64 * 1024, 4096,
 			      SECT_4K | SPI_NOR_DUAL_READ |
 			      SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+	{ "mx25um51345g",  INFO(0xc2813a, 0, 4 * 1024, 16384,
+				SECT_4K | SPI_NOR_OCTAL_READ |
+				SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ |
+				SPI_NOR_OCTAL_DTR_PP |
+				SPI_NOR_IO_MODE_EN_VOLATILE)
+		.fixups = &mx25um51345g_fixups },
 };
 
 static void macronix_default_init(struct spi_nor *nor)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/micron-st.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/micron-st.c
@@ -67,6 +67,10 @@
 	if (ret)
 		return ret;
 
+	if (nor->isstacked &&
+	    !(nor->spimem->spi->master->flags & SPI_MASTER_U_PAGE))
+		return 0;
+
 	/* Read flash ID to make sure the switch was successful. */
 	op = (struct spi_mem_op)
 		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDID, 1),
@@ -125,9 +129,18 @@
 			       SPI_NOR_OCTAL_DTR_PP |
 			       SPI_NOR_IO_MODE_EN_VOLATILE)
 	  .fixups = &mt35xu512aba_fixups},
+	{ "mt35xu01g", INFO(0x2c5b1b, 0, 128 * 1024, 1024,
+			    SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ |
+			    SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ |
+			    SPI_NOR_OCTAL_DTR_PP |
+			    SPI_NOR_IO_MODE_EN_VOLATILE)
+	  .fixups = &mt35xu512aba_fixups},
 	{ "mt35xu02g", INFO(0x2c5b1c, 0, 128 * 1024, 2048,
 			    SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ |
-			    SPI_NOR_4B_OPCODES) },
+			    SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ |
+			    SPI_NOR_OCTAL_DTR_PP |
+			    SPI_NOR_IO_MODE_EN_VOLATILE)
+	  .fixups = &mt35xu512aba_fixups},
 };
 
 static const struct flash_info st_parts[] = {
@@ -141,15 +154,13 @@
 			      SECT_4K | SPI_NOR_QUAD_READ) },
 	{ "n25q064a",    INFO(0x20bb17, 0, 64 * 1024,  128,
 			      SECT_4K | SPI_NOR_QUAD_READ) },
-	{ "n25q128a11",  INFO(0x20bb18, 0, 64 * 1024,  256,
-			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
-			      SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB |
-			      SPI_NOR_4BIT_BP | SPI_NOR_BP3_SR_BIT6) },
-	{ "n25q128a13",  INFO(0x20ba18, 0, 64 * 1024,  256,
-			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
-	{ "mt25ql256a",  INFO6(0x20ba19, 0x104400, 64 * 1024,  512,
-			       SECT_4K | USE_FSR | SPI_NOR_DUAL_READ |
-			       SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+	{ "n25q128a11",  INFO(0x20bb18, 0, 64 * 1024,  256, SECT_4K |
+			SPI_NOR_QUAD_READ | USE_FSR | SPI_NOR_HAS_LOCK) },
+	{ "n25q128a13",  INFO(0x20ba18, 0, 64 * 1024,  256, SECT_4K |
+			SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK) },
+	{ "n25q256a",    INFO(0x20ba19, 0, 64 * 1024,  512, SECT_4K |
+			SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_FSR |
+			SPI_NOR_HAS_LOCK) },
 	{ "n25q256a",    INFO(0x20ba19, 0, 64 * 1024,  512, SECT_4K |
 			      USE_FSR | SPI_NOR_DUAL_READ |
 			      SPI_NOR_QUAD_READ) },
@@ -161,31 +172,29 @@
 	{ "mt25ql512a",  INFO6(0x20ba20, 0x104400, 64 * 1024, 1024,
 			       SECT_4K | USE_FSR | SPI_NOR_DUAL_READ |
 			       SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
-	{ "n25q512ax3",  INFO(0x20ba20, 0, 64 * 1024, 1024,
-			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
-			      SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB |
-			      SPI_NOR_4BIT_BP | SPI_NOR_BP3_SR_BIT6) },
+	{ "n25q512ax3",  INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K |
+			USE_FSR | SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK) },
 	{ "mt25qu512a",  INFO6(0x20bb20, 0x104400, 64 * 1024, 1024,
 			       SECT_4K | USE_FSR | SPI_NOR_DUAL_READ |
-			       SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+			       SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES |
+				   SPI_NOR_HAS_LOCK) },
 	{ "n25q512a",    INFO(0x20bb20, 0, 64 * 1024, 1024,
 			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
 			      SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB |
 			      SPI_NOR_4BIT_BP | SPI_NOR_BP3_SR_BIT6) },
-	{ "n25q00",      INFO(0x20ba21, 0, 64 * 1024, 2048,
-			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
-			      SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB |
-			      SPI_NOR_4BIT_BP | SPI_NOR_BP3_SR_BIT6 |
-			      NO_CHIP_ERASE) },
-	{ "n25q00a",     INFO(0x20bb21, 0, 64 * 1024, 2048,
-			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
-			      NO_CHIP_ERASE) },
+	{ "n25q00",      INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K |
+			USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE |
+			SPI_NOR_HAS_LOCK | SPI_NOR_HAS_LOCK) },
+	{ "n25q00a",     INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K |
+			USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE |
+			SPI_NOR_HAS_LOCK) },
 	{ "mt25ql02g",   INFO(0x20ba22, 0, 64 * 1024, 4096,
 			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
-			      NO_CHIP_ERASE) },
+			      NO_CHIP_ERASE | SPI_NOR_HAS_LOCK) },
 	{ "mt25qu02g",   INFO(0x20bb22, 0, 64 * 1024, 4096,
 			      SECT_4K | USE_FSR | SPI_NOR_DUAL_READ |
-			      SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+			      SPI_NOR_QUAD_READ | NO_CHIP_ERASE |
+				  SPI_NOR_HAS_LOCK) },
 
 	{ "m25p05",  INFO(0x202010,  0,  32 * 1024,   2, 0) },
 	{ "m25p10",  INFO(0x202011,  0,  32 * 1024,   4, 0) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/sfdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/sfdp.c
@@ -874,7 +874,7 @@
 	 */
 	for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++)
 		if (!(regions_erase_type & BIT(erase[i].idx)))
-			spi_nor_set_erase_type(&erase[i], 0, 0xFF);
+			spi_nor_mask_erase_type(&erase[i]);
 
 	return 0;
 }
@@ -1088,7 +1088,7 @@
 			erase_type[i].opcode = (dwords[1] >>
 						erase_type[i].idx * 8) & 0xFF;
 		else
-			spi_nor_set_erase_type(&erase_type[i], 0u, 0xFF);
+			spi_nor_mask_erase_type(&erase_type[i]);
 	}
 
 	/*
@@ -1220,7 +1220,7 @@
 
 	le32_to_cpu_array(dwords, sccr_header->length);
 
-	if (FIELD_GET(SCCR_DWORD22_OCTAL_DTR_EN_VOLATILE, dwords[22]))
+	if (FIELD_GET(SCCR_DWORD22_OCTAL_DTR_EN_VOLATILE, dwords[21]))
 		nor->flags |= SNOR_F_IO_MODE_EN_VOLATILE;
 
 out:
@@ -1378,9 +1378,16 @@
 		case SFDP_SECTOR_MAP_ID:
 			err = spi_nor_parse_smpt(nor, param_header);
 			break;
-
+#ifdef CONFIG_OF
 		case SFDP_4BAIT_ID:
-			err = spi_nor_parse_4bait(nor, param_header);
+			{
+				struct device_node *np = spi_nor_get_flash_node(nor);
+				struct device_node *np_spi = of_get_next_parent(np);
+
+				if (of_property_match_string(np_spi, "compatible",
+							     "xlnx,zynq-qspi-1.0") < 0)
+					err = spi_nor_parse_4bait(nor, param_header);
+			}
 			break;
 
 		case SFDP_PROFILE1_ID:
@@ -1390,7 +1397,7 @@
 		case SFDP_SCCR_MAP_ID:
 			err = spi_nor_parse_sccr(nor, param_header);
 			break;
-
+#endif
 		default:
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/spansion.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/spansion.c
@@ -15,8 +15,13 @@
 #define SPINOR_REG_CYPRESS_CFR3V		0x00800004
 #define SPINOR_REG_CYPRESS_CFR3V_PGSZ		BIT(4) /* Page size. */
 #define SPINOR_REG_CYPRESS_CFR5V		0x00800006
-#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN	0x3
-#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS	0
+#define SPINOR_REG_CYPRESS_CFR5_BIT6		BIT(6)
+#define SPINOR_REG_CYPRESS_CFR5_DDR		BIT(1)
+#define SPINOR_REG_CYPRESS_CFR5_OPI		BIT(0)
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN				\
+	(SPINOR_REG_CYPRESS_CFR5_BIT6 |	SPINOR_REG_CYPRESS_CFR5_DDR |	\
+	 SPINOR_REG_CYPRESS_CFR5_OPI)
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS	SPINOR_REG_CYPRESS_CFR5_BIT6
 #define SPINOR_OP_CYPRESS_RD_FAST		0xee
 
 /**
@@ -204,10 +209,10 @@
 			     SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "s25fl128s0", INFO6(0x012018, 0x4d0080, 256 * 1024, 64,
 			      SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-			      USE_CLSR) },
+			      USE_CLSR | SPI_NOR_HAS_LOCK) },
 	{ "s25fl128s1", INFO6(0x012018, 0x4d0180, 64 * 1024, 256,
 			      SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-			      USE_CLSR) },
+			      USE_CLSR | SPI_NOR_HAS_LOCK) },
 	{ "s25fl256s0", INFO6(0x010219, 0x4d0080, 256 * 1024, 128,
 			      SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			      USE_CLSR) },
@@ -278,13 +283,18 @@
 
 static void spansion_post_sfdp_fixups(struct spi_nor *nor)
 {
+	u32 sector_size = nor->info->sector_size;
+
 	if (nor->params->size <= SZ_16M)
 		return;
 
+	if (nor->isparallel)
+		sector_size <<= 1;
+
 	nor->flags |= SNOR_F_4B_OPCODES;
 	/* No small sector erase for 4-byte command set */
 	nor->erase_opcode = SPINOR_OP_SE;
-	nor->mtd.erasesize = nor->info->sector_size;
+	nor->mtd.erasesize = sector_size;
 }
 
 static const struct spi_nor_fixups spansion_fixups = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/sst.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/sst.c
@@ -81,18 +81,17 @@
 	{ "sst25wf080",  INFO(0xbf2505, 0, 64 * 1024, 16,
 			      SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK | SPI_NOR_SWP_IS_VOLATILE) },
 	{ "sst26wf016b", INFO(0xbf2651, 0, 64 * 1024, 32,
-			      SECT_4K | SPI_NOR_DUAL_READ |
-			      SPI_NOR_QUAD_READ) },
+			      SECT_4K | SST_GLOBAL_PROT_UNLK | SPI_NOR_SWP_IS_VOLATILE) },
 	{ "sst26vf016b", INFO(0xbf2641, 0, 64 * 1024, 32,
-			      SECT_4K | SPI_NOR_DUAL_READ) },
+			      SECT_4K | SST_GLOBAL_PROT_UNLK | SPI_NOR_SWP_IS_VOLATILE) },
 	{ "sst26vf064b", INFO(0xbf2643, 0, 64 * 1024, 128,
 			      SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			      SPI_NOR_HAS_LOCK | SPI_NOR_SWP_IS_VOLATILE)
 		.fixups = &sst26vf_fixups },
 };
 
-static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
-		     size_t *retlen, const u_char *buf)
+int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+	      size_t *retlen, const u_char *buf)
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
 	size_t actual = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/swp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/swp.c
@@ -16,6 +16,8 @@
 
 	if (nor->flags & SNOR_F_HAS_SR_BP3_BIT6)
 		return mask | SR_BP3_BIT6;
+	else if (nor->flags & SNOR_F_HAS_SR_BP3_BIT5)
+		return mask | SR_BP3_BIT5;
 
 	if (nor->flags & SNOR_F_HAS_4BIT_BP)
 		return mask | SR_BP3;
@@ -35,16 +37,24 @@
 {
 	unsigned int bp_slots, bp_slots_needed;
 	u8 mask = spi_nor_get_sr_bp_mask(nor);
+	u32 n_sectors = nor->info->n_sectors;
+	u32 sector_size = nor->info->sector_size;
+
+	if (nor->isstacked)
+		n_sectors <<= 1;
+
+	if (nor->isparallel)
+		sector_size <<= 1;
 
 	/* Reserved one for "protect none" and one for "protect all". */
 	bp_slots = (1 << hweight8(mask)) - 2;
-	bp_slots_needed = ilog2(nor->info->n_sectors);
+	bp_slots_needed = ilog2(n_sectors);
 
 	if (bp_slots_needed > bp_slots)
-		return nor->info->sector_size <<
+		return sector_size <<
 			(bp_slots_needed - bp_slots);
 	else
-		return nor->info->sector_size;
+		return sector_size;
 }
 
 static void spi_nor_get_locked_range_sr(struct spi_nor *nor, u8 sr, loff_t *ofs,
@@ -203,6 +213,9 @@
 
 		if (nor->flags & SNOR_F_HAS_SR_BP3_BIT6 && val & SR_BP3)
 			val = (val & ~SR_BP3) | SR_BP3_BIT6;
+		else if (nor->flags & SNOR_F_HAS_SR_BP3_BIT5 &&
+			 val & SR_BP3_BIT5)
+			val |= SR_BP3_BIT5;
 
 		if (val & ~mask)
 			return -EINVAL;
@@ -283,11 +296,14 @@
 		val = 0; /* fully unlocked */
 	} else {
 		min_prot_len = spi_nor_get_min_prot_length_sr(nor);
-		pow = ilog2(lock_len) - ilog2(min_prot_len) + 1;
+		pow = ilog2(mtd->size) - ilog2(min_prot_len) + 1;
 		val = pow << SR_BP_SHIFT;
 
 		if (nor->flags & SNOR_F_HAS_SR_BP3_BIT6 && val & SR_BP3)
 			val = (val & ~SR_BP3) | SR_BP3_BIT6;
+		else if (nor->flags & SNOR_F_HAS_SR_BP3_BIT5 &&
+			 val & SR_BP3_BIT5)
+			val |= SR_BP3_BIT5;
 
 		/* Some power-of-two sizes are not supported */
 		if (val & ~mask)
@@ -343,17 +359,166 @@
 	nor->params->locking_ops = &spi_nor_sr_locking_ops;
 }
 
+static int write_sr_modify_protection(struct spi_nor *nor, u8 status,
+				      u8 lock_bits)
+{
+	u8 status_new, bp_mask;
+
+	status_new = status & ~SR_BP_BIT_MASK;
+	bp_mask = (lock_bits << SR_BP_BIT_OFFSET) & SR_BP_BIT_MASK;
+
+	/* Micron */
+	if (nor->jedec_id == CFI_MFR_ST) {
+		/* To support chips with more than 896 sectors (56MB) */
+		status_new &= ~SR_BP3;
+
+		/* Protected area starts from top */
+		status_new &= ~SR_BP_TB;
+
+		if (lock_bits > 7)
+			bp_mask |= SR_BP3;
+	} else if (nor->jedec_id == CFI_MFR_WINBND) { /* Winbond */
+		status_new &= ~SR_BP3_BIT5;
+
+		/* Protected area starts from top */
+		status_new &= ~SR_BP_TB;
+
+		if (lock_bits > 7)
+			bp_mask |= SR_BP3_BIT5;
+	}
+
+	if (nor->is_lock)
+		status_new |= bp_mask;
+
+	/* For spansion flashes */
+	if (nor->jedec_id == CFI_MFR_AMD) {
+		spi_nor_read_cr(nor, &nor->bouncebuf[1]);
+		nor->bouncebuf[0] |= status_new;
+		if (spi_nor_write_sr(nor, nor->bouncebuf, 2) < 0)
+			return 1;
+	} else {
+		nor->bouncebuf[0] = status_new;
+		if (spi_nor_write_sr(nor, &nor->bouncebuf[0], 1) < 0)
+			return 1;
+	}
+	return 0;
+}
+
+static u8 bp_bits_from_sr(struct spi_nor *nor, u8 status)
+{
+	u8 ret;
+
+	ret = (((status) & SR_BP_BIT_MASK) >> SR_BP_BIT_OFFSET);
+	if (nor->jedec_id == 0x20)
+		ret |= ((status & SR_BP3) >> (SR_BP_BIT_OFFSET + 1));
+	else if ((nor->jedec_id == CFI_MFR_WINBND) &&
+		 (nor->flags & SNOR_F_HAS_4BIT_BP))
+		ret |= ((status & SR_BP3_BIT5) >> SR_BP_BIT_OFFSET);
+
+	return ret;
+}
+
+static inline u16 min_lockable_sectors(struct spi_nor *nor,
+				       u16 n_sectors)
+{
+	u16 lock_granularity;
+
+	/*
+	 * Revisit - SST (not used by us) has the same JEDEC ID as micron but
+	 * protected area table is similar to that of spansion.
+	 */
+	lock_granularity = max(1, n_sectors / M25P_MAX_LOCKABLE_SECTORS);
+	if (nor->jedec_id == CFI_MFR_ST)	/* Micron */
+		lock_granularity = 1;
+
+	return lock_granularity;
+}
+
+static inline uint32_t get_protected_area_start(struct spi_nor *nor,
+						u8 lock_bits)
+{
+	u16 n_sectors;
+	u32 sector_size;
+	u64 mtd_size;
+	struct mtd_info *mtd = &nor->mtd;
+
+	n_sectors = nor->n_sectors;
+	sector_size = nor->sector_size;
+	mtd_size = mtd->size;
+
+	if (nor->isparallel) {
+		sector_size = (nor->sector_size >> 1);
+		mtd_size = (mtd->size >> 1);
+	}
+	if (nor->isstacked) {
+		n_sectors = (nor->n_sectors >> 1);
+		mtd_size = (mtd->size >> 1);
+	}
+
+	return mtd_size - (1 << (lock_bits - 1)) *
+		min_lockable_sectors(nor, n_sectors) * sector_size;
+}
+
+static u8 min_protected_area_including_offset(struct spi_nor *nor,
+					      uint32_t offset)
+{
+	u8 lock_bits, lockbits_limit;
+
+	/*
+	 * Revisit - SST (not used by us) has the same JEDEC ID as micron but
+	 * protected area table is similar to that of spansion.
+	 * Mircon has 4 block protect bits.
+	 */
+	lockbits_limit = 7;
+	if (nor->jedec_id == CFI_MFR_ST)	/* Micron */
+		lockbits_limit = 15;
+
+	for (lock_bits = 1; lock_bits < lockbits_limit; lock_bits++) {
+		if (offset >= get_protected_area_start(nor, lock_bits))
+			break;
+	}
+	return lock_bits;
+}
+
 static int spi_nor_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
 	int ret;
+	u8 lock_bits;
 
 	ret = spi_nor_lock_and_prep(nor);
 	if (ret)
 		return ret;
 
+	if (nor->isparallel == 1)
+		ofs = ofs >> nor->shift;
+
+	if (nor->isstacked == 1) {
+		if (ofs >= (mtd->size / 2)) {
+			ofs = ofs - (mtd->size / 2);
+			nor->spimem->spi->master->flags |= SPI_MASTER_U_PAGE;
+		} else {
+			nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+		}
+	}
 	ret = nor->params->locking_ops->lock(nor, ofs, len);
+	/* Wait until finished previous command */
+	ret = spi_nor_wait_till_ready(nor);
+	if (ret)
+		goto err;
+
+	ret = spi_nor_read_sr(nor, nor->bouncebuf);
+
+	lock_bits = min_protected_area_including_offset(nor, ofs);
 
+	/* Only modify protection if it will not unlock other areas */
+	if (lock_bits > bp_bits_from_sr(nor, nor->bouncebuf[0])) {
+		nor->is_lock = 1;
+		ret = write_sr_modify_protection(nor, nor->bouncebuf[0], lock_bits);
+	} else {
+		dev_err(nor->dev, "trying to unlock already locked area\n");
+	}
+err:
 	spi_nor_unlock_and_unprep(nor);
 	return ret;
 }
@@ -362,13 +527,40 @@
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
 	int ret;
+	u8 lock_bits;
 
 	ret = spi_nor_lock_and_prep(nor);
 	if (ret)
 		return ret;
 
+	if (nor->isparallel == 1)
+		ofs = ofs >> nor->shift;
+
+	if (nor->isstacked == 1) {
+		if (ofs >= (mtd->size / 2)) {
+			ofs = ofs - (mtd->size / 2);
+			nor->spimem->spi->master->flags |= SPI_MASTER_U_PAGE;
+		} else {
+			nor->spimem->spi->master->flags &= ~SPI_MASTER_U_PAGE;
+		}
+	}
 	ret = nor->params->locking_ops->unlock(nor, ofs, len);
+	/* Wait until finished previous command */
+	ret = spi_nor_wait_till_ready(nor);
+	if (ret)
+		goto err;
+
+	ret = spi_nor_read_sr(nor, nor->bouncebuf);
 
+	lock_bits = min_protected_area_including_offset(nor, ofs + len) - 1;
+	/* Only modify protection if it will not lock other areas */
+	if (lock_bits < bp_bits_from_sr(nor, nor->bouncebuf[0])) {
+		nor->is_lock = 0;
+		ret = write_sr_modify_protection(nor, nor->bouncebuf[0], lock_bits);
+	} else {
+		dev_err(nor->dev, "trying to lock already unlocked area\n");
+	}
+err:
 	spi_nor_unlock_and_unprep(nor);
 	return ret;
 }
@@ -388,6 +580,26 @@
 	return ret;
 }
 
+static void spi_nor_prot_unlock(struct spi_nor *nor)
+{
+	if (nor->info->flags & SST_GLOBAL_PROT_UNLK) {
+		spi_nor_write_enable(nor);
+		if (nor->spimem) {
+			struct spi_mem_op op =
+				SPI_MEM_OP(SPI_MEM_OP_CMD(GLOBAL_BLKPROT_UNLK, 1),
+					   SPI_MEM_OP_NO_ADDR,
+					   SPI_MEM_OP_NO_DUMMY,
+					   SPI_MEM_OP_NO_DATA);
+
+			spi_mem_exec_op(nor->spimem, &op);
+		} else {
+			/* Unlock global write protection bits */
+			nor->controller_ops->write_reg(nor, GLOBAL_BLKPROT_UNLK, NULL, 0);
+		}
+	}
+	spi_nor_wait_till_ready(nor);
+}
+
 /**
  * spi_nor_try_unlock_all() - Tries to unlock the entire flash memory array.
  * @nor:	pointer to a 'struct spi_nor'.
@@ -403,15 +615,20 @@
 void spi_nor_try_unlock_all(struct spi_nor *nor)
 {
 	int ret;
+	const struct flash_info *info = nor->info;
 
-	if (!(nor->flags & SNOR_F_HAS_LOCK))
-		return;
-
-	dev_dbg(nor->dev, "Unprotecting entire flash array\n");
-
-	ret = spi_nor_unlock(&nor->mtd, 0, nor->params->size);
-	if (ret)
-		dev_dbg(nor->dev, "Failed to unlock the entire flash memory array\n");
+	if (nor->jedec_id == CFI_MFR_ATMEL ||
+	    nor->jedec_id == CFI_MFR_INTEL ||
+	    nor->jedec_id == CFI_MFR_SST ||
+	    nor->flags & SNOR_F_HAS_LOCK) {
+		if (info->flags & SST_GLOBAL_PROT_UNLK) {
+			spi_nor_prot_unlock(nor);
+		} else {
+			ret = spi_nor_unlock(&nor->mtd, 0, nor->params->size);
+			if (ret)
+				dev_dbg(nor->dev, "Failed to unlock the entire flash memory array\n");
+		}
+	}
 }
 
 void spi_nor_register_locking_ops(struct spi_nor *nor)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/sysfs.c
@@ -67,6 +67,19 @@
 	NULL
 };
 
+static umode_t spi_nor_sysfs_is_visible(struct kobject *kobj,
+					struct attribute *attr, int n)
+{
+	struct spi_device *spi = to_spi_device(kobj_to_dev(kobj));
+	struct spi_mem *spimem = spi_get_drvdata(spi);
+	struct spi_nor *nor = spi_mem_get_drvdata(spimem);
+
+	if (attr == &dev_attr_jedec_id.attr && !nor->info->id_len)
+		return 0;
+
+	return 0444;
+}
+
 static umode_t spi_nor_sysfs_is_bin_visible(struct kobject *kobj,
 					    struct bin_attribute *attr, int n)
 {
@@ -82,6 +95,7 @@
 
 static const struct attribute_group spi_nor_sysfs_group = {
 	.name		= "spi-nor",
+	.is_visible	= spi_nor_sysfs_is_visible,
 	.is_bin_visible	= spi_nor_sysfs_is_bin_visible,
 	.attrs		= spi_nor_sysfs_entries,
 	.bin_attrs	= spi_nor_sysfs_bin_entries,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/winbond.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/winbond.c
@@ -100,6 +100,11 @@
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
 			    SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
+	{ "w25h02jv", INFO(0xef9022, 0, 64 * 1024, 4096,
+			    SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ |
+			    SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB |
+			    SPI_NOR_TB_SR_BIT6 | SPI_NOR_4BIT_BP |
+			    SPI_NOR_BP3_SR_BIT5 | SPI_NOR_4B_OPCODES) },
 	{ "w25q512jvq", INFO(0xef4020, 0, 64 * 1024, 1024,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/spi-nor/xilinx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/spi-nor/xilinx.c
@@ -66,7 +66,8 @@
 		/* Flash in Power of 2 mode */
 		nor->page_size = (nor->page_size == 264) ? 256 : 512;
 		nor->mtd.writebufsize = nor->page_size;
-		nor->mtd.size = 8 * nor->page_size * nor->info->n_sectors;
+		nor->params->size = 8 * nor->page_size * nor->info->n_sectors;
+		nor->mtd.size = nor->params->size;
 		nor->mtd.erasesize = 8 * nor->page_size;
 	} else {
 		/* Flash in Default addressing mode */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/tests/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/tests/Makefile
@@ -1,19 +1,19 @@
 # SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_MTD_TESTS) += mtd_oobtest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_pagetest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_readtest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_speedtest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_stresstest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_subpagetest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_torturetest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_nandecctest.o
-obj-$(CONFIG_MTD_TESTS) += mtd_nandbiterrs.o
+obj-$(CONFIG_MTD_TESTS) += mtd_oobtest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_pagetest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_readtest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_speedtest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_stresstest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_subpagetest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_torturetest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_nandecctest.o mtd_test.o
+obj-$(CONFIG_MTD_TESTS) += mtd_nandbiterrs.o mtd_test.o
 
-mtd_oobtest-objs := oobtest.o mtd_test.o
-mtd_pagetest-objs := pagetest.o mtd_test.o
-mtd_readtest-objs := readtest.o mtd_test.o
-mtd_speedtest-objs := speedtest.o mtd_test.o
-mtd_stresstest-objs := stresstest.o mtd_test.o
-mtd_subpagetest-objs := subpagetest.o mtd_test.o
-mtd_torturetest-objs := torturetest.o mtd_test.o
-mtd_nandbiterrs-objs := nandbiterrs.o mtd_test.o
+mtd_oobtest-objs := oobtest.o
+mtd_pagetest-objs := pagetest.o
+mtd_readtest-objs := readtest.o
+mtd_speedtest-objs := speedtest.o
+mtd_stresstest-objs := stresstest.o
+mtd_subpagetest-objs := subpagetest.o
+mtd_torturetest-objs := torturetest.o
+mtd_nandbiterrs-objs := nandbiterrs.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/tests/mtd_test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/tests/mtd_test.c
@@ -25,6 +25,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mtdtest_erase_eraseblock);
 
 static int is_block_bad(struct mtd_info *mtd, unsigned int ebnum)
 {
@@ -57,6 +58,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mtdtest_scan_for_bad_eraseblocks);
 
 int mtdtest_erase_good_eraseblocks(struct mtd_info *mtd, unsigned char *bbt,
 				unsigned int eb, int ebcnt)
@@ -75,6 +77,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mtdtest_erase_good_eraseblocks);
 
 int mtdtest_read(struct mtd_info *mtd, loff_t addr, size_t size, void *buf)
 {
@@ -92,6 +95,7 @@
 
 	return err;
 }
+EXPORT_SYMBOL_GPL(mtdtest_read);
 
 int mtdtest_write(struct mtd_info *mtd, loff_t addr, size_t size,
 		const void *buf)
@@ -107,3 +111,8 @@
 
 	return err;
 }
+EXPORT_SYMBOL_GPL(mtdtest_write);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MTD function test helpers");
+MODULE_AUTHOR("Akinobu Mita");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/tests/speedtest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/tests/speedtest.c
@@ -160,14 +160,13 @@
 
 static long calc_speed(void)
 {
-	uint64_t k;
-	long ms;
+	uint64_t k, us;
 
-	ms = ktime_ms_delta(finish, start);
-	if (ms == 0)
+	us = ktime_us_delta(finish, start);
+	if (us == 0)
 		return 0;
-	k = (uint64_t)goodebcnt * (mtd->erasesize / 1024) * 1000;
-	do_div(k, ms);
+	k = (uint64_t)goodebcnt * (mtd->erasesize / 1024) * 1000000;
+	do_div(k, us);
 	return k;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/attach.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/attach.c
@@ -1447,7 +1447,7 @@
 	return err;
 }
 
-static struct ubi_attach_info *alloc_ai(void)
+static struct ubi_attach_info *alloc_ai(const char *slab_name)
 {
 	struct ubi_attach_info *ai;
 
@@ -1461,7 +1461,7 @@
 	INIT_LIST_HEAD(&ai->alien);
 	INIT_LIST_HEAD(&ai->fastmap);
 	ai->volumes = RB_ROOT;
-	ai->aeb_slab_cache = kmem_cache_create("ubi_aeb_slab_cache",
+	ai->aeb_slab_cache = kmem_cache_create(slab_name,
 					       sizeof(struct ubi_ainf_peb),
 					       0, 0, NULL);
 	if (!ai->aeb_slab_cache) {
@@ -1491,7 +1491,7 @@
 
 	err = -ENOMEM;
 
-	scan_ai = alloc_ai();
+	scan_ai = alloc_ai("ubi_aeb_slab_cache_fastmap");
 	if (!scan_ai)
 		goto out;
 
@@ -1557,7 +1557,7 @@
 	int err;
 	struct ubi_attach_info *ai;
 
-	ai = alloc_ai();
+	ai = alloc_ai("ubi_aeb_slab_cache");
 	if (!ai)
 		return -ENOMEM;
 
@@ -1575,7 +1575,7 @@
 		if (err > 0 || mtd_is_eccerr(err)) {
 			if (err != UBI_NO_FASTMAP) {
 				destroy_ai(ai);
-				ai = alloc_ai();
+				ai = alloc_ai("ubi_aeb_slab_cache");
 				if (!ai)
 					return -ENOMEM;
 
@@ -1614,7 +1614,7 @@
 	if (ubi->fm && ubi_dbg_chk_fastmap(ubi)) {
 		struct ubi_attach_info *scan_ai;
 
-		scan_ai = alloc_ai();
+		scan_ai = alloc_ai("ubi_aeb_slab_cache_dbg_chk_fastmap");
 		if (!scan_ai) {
 			err = -ENOMEM;
 			goto out_wl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/build.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/build.c
@@ -351,9 +351,6 @@
 	 * we still can use 'ubi->ubi_num'.
 	 */
 	ubi = container_of(dev, struct ubi_device, dev);
-	ubi = ubi_get_device(ubi->ubi_num);
-	if (!ubi)
-		return -ENODEV;
 
 	if (attr == &dev_eraseblock_size)
 		ret = sprintf(buf, "%d\n", ubi->leb_size);
@@ -382,7 +379,6 @@
 	else
 		ret = -EINVAL;
 
-	ubi_put_device(ubi);
 	return ret;
 }
 
@@ -472,6 +468,7 @@
 			err = ubi_add_volume(ubi, ubi->volumes[i]);
 			if (err) {
 				ubi_err(ubi, "cannot add volume %d", i);
+				ubi->volumes[i] = NULL;
 				goto out_volumes;
 			}
 		}
@@ -684,6 +681,21 @@
 						ubi->vid_hdr_aloffset;
 	}
 
+	/*
+	 * Memory allocation for VID header is ubi->vid_hdr_alsize
+	 * which is described in comments in io.c.
+	 * Make sure VID header shift + UBI_VID_HDR_SIZE not exceeds
+	 * ubi->vid_hdr_alsize, so that all vid header operations
+	 * won't access memory out of bounds.
+	 */
+	if ((ubi->vid_hdr_shift + UBI_VID_HDR_SIZE) > ubi->vid_hdr_alsize) {
+		ubi_err(ubi, "Invalid VID header offset %d, VID header shift(%d)"
+			" + VID header size(%zu) > VID header aligned size(%d).",
+			ubi->vid_hdr_offset, ubi->vid_hdr_shift,
+			UBI_VID_HDR_SIZE, ubi->vid_hdr_alsize);
+		return -EINVAL;
+	}
+
 	/* Similar for the data offset */
 	ubi->leb_start = ubi->vid_hdr_offset + UBI_VID_HDR_SIZE;
 	ubi->leb_start = ALIGN(ubi->leb_start, ubi->min_io_size);
@@ -876,6 +888,20 @@
 		return -EINVAL;
 	}
 
+	/* UBI cannot work on flashes with zero erasesize. */
+	if (!mtd->erasesize) {
+		pr_err("ubi: refuse attaching mtd%d - zero erasesize flash is not supported\n",
+			mtd->index);
+		return -EINVAL;
+	}
+
+	/* UBI cannot work on flashes with zero erasesize. */
+	if (!mtd->erasesize) {
+		pr_err("ubi: refuse attaching mtd%d - zero erasesize flash is not supported\n",
+			mtd->index);
+		return -EINVAL;
+	}
+
 	if (ubi_num == UBI_DEV_NUM_AUTO) {
 		/* Search for an empty slot in the @ubi_devices array */
 		for (ubi_num = 0; ubi_num < UBI_MAX_DEVICES; ubi_num++)
@@ -979,9 +1005,6 @@
 			goto out_detach;
 	}
 
-	/* Make device "available" before it becomes accessible via sysfs */
-	ubi_devices[ubi_num] = ubi;
-
 	err = uif_init(ubi);
 	if (err)
 		goto out_detach;
@@ -1026,6 +1049,7 @@
 	wake_up_process(ubi->bgt_thread);
 	spin_unlock(&ubi->wl_lock);
 
+	ubi_devices[ubi_num] = ubi;
 	ubi_notify_all(ubi, UBI_VOLUME_ADDED, NULL);
 	return ubi_num;
 
@@ -1034,7 +1058,6 @@
 out_uif:
 	uif_close(ubi);
 out_detach:
-	ubi_devices[ubi_num] = NULL;
 	ubi_wl_close(ubi);
 	ubi_free_all_volumes(ubi);
 	vfree(ubi->vtbl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/eba.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/eba.c
@@ -946,7 +946,7 @@
 				  int offset, int len)
 {
 	struct ubi_device *ubi = vol->ubi;
-	int pnum, opnum, err, vol_id = vol->vol_id;
+	int pnum, opnum, err, err2, vol_id = vol->vol_id;
 
 	pnum = ubi_wl_get_peb(ubi);
 	if (pnum < 0) {
@@ -981,10 +981,19 @@
 out_put:
 	up_read(&ubi->fm_eba_sem);
 
-	if (err && pnum >= 0)
-		err = ubi_wl_put_peb(ubi, vol_id, lnum, pnum, 1);
-	else if (!err && opnum >= 0)
-		err = ubi_wl_put_peb(ubi, vol_id, lnum, opnum, 0);
+	if (err && pnum >= 0) {
+		err2 = ubi_wl_put_peb(ubi, vol_id, lnum, pnum, 1);
+		if (err2) {
+			ubi_warn(ubi, "failed to return physical eraseblock %d, error %d",
+				 pnum, err2);
+		}
+	} else if (!err && opnum >= 0) {
+		err2 = ubi_wl_put_peb(ubi, vol_id, lnum, opnum, 0);
+		if (err2) {
+			ubi_warn(ubi, "failed to return physical eraseblock %d, error %d",
+				 opnum, err2);
+		}
+	}
 
 	return err;
 }
@@ -1551,6 +1560,7 @@
 					  GFP_KERNEL);
 		if (!fm_eba[i]) {
 			ret = -ENOMEM;
+			kfree(scan_eba[i]);
 			goto out_free;
 		}
 
@@ -1586,7 +1596,7 @@
 	}
 
 out_free:
-	for (i = 0; i < num_volumes; i++) {
+	while (--i >= 0) {
 		if (!ubi->volumes[i])
 			continue;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/fastmap-wl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/fastmap-wl.c
@@ -97,6 +97,33 @@
 	return e;
 }
 
+/*
+ * has_enough_free_count - whether ubi has enough free pebs to fill fm pools
+ * @ubi: UBI device description object
+ * @is_wl_pool: whether UBI is filling wear leveling pool
+ *
+ * This helper function checks whether there are enough free pebs (deducted
+ * by fastmap pebs) to fill fm_pool and fm_wl_pool, above rule works after
+ * there is at least one of free pebs is filled into fm_wl_pool.
+ * For wear leveling pool, UBI should also reserve free pebs for bad pebs
+ * handling, because there maybe no enough free pebs for user volumes after
+ * producing new bad pebs.
+ */
+static bool has_enough_free_count(struct ubi_device *ubi, bool is_wl_pool)
+{
+	int fm_used = 0;	// fastmap non anchor pebs.
+	int beb_rsvd_pebs;
+
+	if (!ubi->free.rb_node)
+		return false;
+
+	beb_rsvd_pebs = is_wl_pool ? ubi->beb_rsvd_pebs : 0;
+	if (ubi->fm_wl_pool.size > 0 && !(ubi->ro_mode || ubi->fm_disabled))
+		fm_used = ubi->fm_size / ubi->leb_size - 1;
+
+	return ubi->free_count - beb_rsvd_pebs > fm_used;
+}
+
 /**
  * ubi_refill_pools - refills all fastmap PEB pools.
  * @ubi: UBI device description object
@@ -119,22 +146,20 @@
 	if (ubi->fm_anchor) {
 		wl_tree_add(ubi->fm_anchor, &ubi->free);
 		ubi->free_count++;
-	}
-	if (ubi->fm_next_anchor) {
-		wl_tree_add(ubi->fm_next_anchor, &ubi->free);
-		ubi->free_count++;
+		ubi->fm_anchor = NULL;
 	}
 
-	/* All available PEBs are in ubi->free, now is the time to get
-	 * the best anchor PEBs.
-	 */
-	ubi->fm_anchor = ubi_wl_get_fm_peb(ubi, 1);
-	ubi->fm_next_anchor = ubi_wl_get_fm_peb(ubi, 1);
+	if (!ubi->fm_disabled)
+		/*
+		 * All available PEBs are in ubi->free, now is the time to get
+		 * the best anchor PEBs.
+		 */
+		ubi->fm_anchor = ubi_wl_get_fm_peb(ubi, 1);
 
 	for (;;) {
 		enough = 0;
 		if (pool->size < pool->max_size) {
-			if (!ubi->free.rb_node)
+			if (!has_enough_free_count(ubi, false))
 				break;
 
 			e = wl_get_wle(ubi);
@@ -147,8 +172,7 @@
 			enough++;
 
 		if (wl_pool->size < wl_pool->max_size) {
-			if (!ubi->free.rb_node ||
-			   (ubi->free_count - ubi->beb_rsvd_pebs < 5))
+			if (!has_enough_free_count(ubi, true))
 				break;
 
 			e = find_wl_entry(ubi, &ubi->free, WL_FREE_MAX_DIFF);
@@ -286,20 +310,26 @@
 int ubi_ensure_anchor_pebs(struct ubi_device *ubi)
 {
 	struct ubi_work *wrk;
+	struct ubi_wl_entry *anchor;
 
 	spin_lock(&ubi->wl_lock);
 
-	/* Do we have a next anchor? */
-	if (!ubi->fm_next_anchor) {
-		ubi->fm_next_anchor = ubi_wl_get_fm_peb(ubi, 1);
-		if (!ubi->fm_next_anchor)
-			/* Tell wear leveling to produce a new anchor PEB */
-			ubi->fm_do_produce_anchor = 1;
+	/* Do we already have an anchor? */
+	if (ubi->fm_anchor) {
+		spin_unlock(&ubi->wl_lock);
+		return 0;
 	}
 
-	/* Do wear leveling to get a new anchor PEB or check the
-	 * existing next anchor candidate.
-	 */
+	/* See if we can find an anchor PEB on the list of free PEBs */
+	anchor = ubi_wl_get_fm_peb(ubi, 1);
+	if (anchor) {
+		ubi->fm_anchor = anchor;
+		spin_unlock(&ubi->wl_lock);
+		return 0;
+	}
+
+	ubi->fm_do_produce_anchor = 1;
+	/* No luck, trigger wear leveling to produce a new anchor PEB. */
 	if (ubi->wl_scheduled) {
 		spin_unlock(&ubi->wl_lock);
 		return 0;
@@ -381,11 +411,6 @@
 		ubi->fm_anchor = NULL;
 	}
 
-	if (ubi->fm_next_anchor) {
-		return_unused_peb(ubi, ubi->fm_next_anchor);
-		ubi->fm_next_anchor = NULL;
-	}
-
 	if (ubi->fm) {
 		for (i = 0; i < ubi->fm->used_blocks; i++)
 			kfree(ubi->fm->e[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/fastmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/fastmap.c
@@ -86,9 +86,10 @@
 		sizeof(struct ubi_fm_scan_pool) +
 		sizeof(struct ubi_fm_scan_pool) +
 		(ubi->peb_count * sizeof(struct ubi_fm_ec)) +
-		(sizeof(struct ubi_fm_eba) +
-		(ubi->peb_count * sizeof(__be32))) +
-		sizeof(struct ubi_fm_volhdr) * UBI_MAX_VOLUMES;
+		((sizeof(struct ubi_fm_eba) +
+		  sizeof(struct ubi_fm_volhdr)) *
+		 (UBI_MAX_VOLUMES + UBI_INT_VOL_COUNT)) +
+		(ubi->peb_count * sizeof(__be32));
 	return roundup(size, ubi->leb_size);
 }
 
@@ -468,7 +469,9 @@
 			if (err == UBI_IO_FF_BITFLIPS)
 				scrub = 1;
 
-			add_aeb(ai, free, pnum, ec, scrub);
+			ret = add_aeb(ai, free, pnum, ec, scrub);
+			if (ret)
+				goto out;
 			continue;
 		} else if (err == 0 || err == UBI_IO_BITFLIPS) {
 			dbg_bld("Found non empty PEB:%i in pool", pnum);
@@ -638,8 +641,10 @@
 		if (fm_pos >= fm_size)
 			goto fail_bad;
 
-		add_aeb(ai, &ai->free, be32_to_cpu(fmec->pnum),
-			be32_to_cpu(fmec->ec), 0);
+		ret = add_aeb(ai, &ai->free, be32_to_cpu(fmec->pnum),
+			      be32_to_cpu(fmec->ec), 0);
+		if (ret)
+			goto fail;
 	}
 
 	/* read EC values from used list */
@@ -649,8 +654,10 @@
 		if (fm_pos >= fm_size)
 			goto fail_bad;
 
-		add_aeb(ai, &used, be32_to_cpu(fmec->pnum),
-			be32_to_cpu(fmec->ec), 0);
+		ret = add_aeb(ai, &used, be32_to_cpu(fmec->pnum),
+			      be32_to_cpu(fmec->ec), 0);
+		if (ret)
+			goto fail;
 	}
 
 	/* read EC values from scrub list */
@@ -660,8 +667,10 @@
 		if (fm_pos >= fm_size)
 			goto fail_bad;
 
-		add_aeb(ai, &used, be32_to_cpu(fmec->pnum),
-			be32_to_cpu(fmec->ec), 1);
+		ret = add_aeb(ai, &used, be32_to_cpu(fmec->pnum),
+			      be32_to_cpu(fmec->ec), 1);
+		if (ret)
+			goto fail;
 	}
 
 	/* read EC values from erase list */
@@ -671,8 +680,10 @@
 		if (fm_pos >= fm_size)
 			goto fail_bad;
 
-		add_aeb(ai, &ai->erase, be32_to_cpu(fmec->pnum),
-			be32_to_cpu(fmec->ec), 1);
+		ret = add_aeb(ai, &ai->erase, be32_to_cpu(fmec->pnum),
+			      be32_to_cpu(fmec->ec), 1);
+		if (ret)
+			goto fail;
 	}
 
 	ai->mean_ec = div_u64(ai->ec_sum, ai->ec_count);
@@ -1218,17 +1229,6 @@
 
 		free_peb_count++;
 		fm_pos += sizeof(*fec);
-		ubi_assert(fm_pos <= ubi->fm_size);
-	}
-	if (ubi->fm_next_anchor) {
-		fec = (struct ubi_fm_ec *)(fm_raw + fm_pos);
-
-		fec->pnum = cpu_to_be32(ubi->fm_next_anchor->pnum);
-		set_seen(ubi, ubi->fm_next_anchor->pnum, seen_pebs);
-		fec->ec = cpu_to_be32(ubi->fm_next_anchor->ec);
-
-		free_peb_count++;
-		fm_pos += sizeof(*fec);
 		ubi_assert(fm_pos <= ubi->fm_size);
 	}
 	fmh->free_peb_count = cpu_to_be32(free_peb_count);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/ubi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/ubi.h
@@ -489,8 +489,7 @@
  * @fm_work: fastmap work queue
  * @fm_work_scheduled: non-zero if fastmap work was scheduled
  * @fast_attach: non-zero if UBI was attached by fastmap
- * @fm_anchor: The new anchor PEB used during fastmap update
- * @fm_next_anchor: An anchor PEB candidate for the next time fastmap is updated
+ * @fm_anchor: The next anchor PEB to use for fastmap
  * @fm_do_produce_anchor: If true produce an anchor PEB in wl
  *
  * @used: RB-tree of used physical eraseblocks
@@ -601,7 +600,6 @@
 	int fm_work_scheduled;
 	int fast_attach;
 	struct ubi_wl_entry *fm_anchor;
-	struct ubi_wl_entry *fm_next_anchor;
 	int fm_do_produce_anchor;
 
 	/* Wear-leveling sub-system's stuff */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/vmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/vmt.c
@@ -56,16 +56,11 @@
 {
 	int ret;
 	struct ubi_volume *vol = container_of(dev, struct ubi_volume, dev);
-	struct ubi_device *ubi;
-
-	ubi = ubi_get_device(vol->ubi->ubi_num);
-	if (!ubi)
-		return -ENODEV;
+	struct ubi_device *ubi = vol->ubi;
 
 	spin_lock(&ubi->volumes_lock);
 	if (!ubi->volumes[vol->vol_id]) {
 		spin_unlock(&ubi->volumes_lock);
-		ubi_put_device(ubi);
 		return -ENODEV;
 	}
 	/* Take a reference to prevent volume removal */
@@ -103,7 +98,6 @@
 	vol->ref_count -= 1;
 	ubi_assert(vol->ref_count >= 0);
 	spin_unlock(&ubi->volumes_lock);
-	ubi_put_device(ubi);
 	return ret;
 }
 
@@ -315,7 +309,6 @@
 	ubi->volumes[vol_id] = NULL;
 	ubi->vol_count -= 1;
 	spin_unlock(&ubi->volumes_lock);
-	ubi_eba_destroy_table(eba_tbl);
 out_acc:
 	spin_lock(&ubi->volumes_lock);
 	ubi->rsvd_pebs -= vol->reserved_pebs;
@@ -471,7 +464,7 @@
 		for (i = 0; i < -pebs; i++) {
 			err = ubi_eba_unmap_leb(ubi, vol, reserved_pebs + i);
 			if (err)
-				goto out_acc;
+				goto out_free;
 		}
 		spin_lock(&ubi->volumes_lock);
 		ubi->rsvd_pebs += pebs;
@@ -519,8 +512,10 @@
 		ubi->avail_pebs += pebs;
 		spin_unlock(&ubi->volumes_lock);
 	}
+	return err;
+
 out_free:
-	kfree(new_eba_tbl);
+	ubi_eba_destroy_table(new_eba_tbl);
 	return err;
 }
 
@@ -587,6 +582,7 @@
 	if (err) {
 		ubi_err(ubi, "cannot add character device for volume %d, error %d",
 			vol_id, err);
+		vol_release(&vol->dev);
 		return err;
 	}
 
@@ -597,15 +593,14 @@
 	vol->dev.groups = volume_dev_groups;
 	dev_set_name(&vol->dev, "%s_%d", ubi->ubi_name, vol->vol_id);
 	err = device_register(&vol->dev);
-	if (err)
-		goto out_cdev;
+	if (err) {
+		cdev_del(&vol->cdev);
+		put_device(&vol->dev);
+		return err;
+	}
 
 	self_check_volumes(ubi);
 	return err;
-
-out_cdev:
-	cdev_del(&vol->cdev);
-	return err;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/vtbl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/vtbl.c
@@ -791,6 +791,12 @@
 	 * The number of supported volumes is limited by the eraseblock size
 	 * and by the UBI_MAX_VOLUMES constant.
 	 */
+
+	if (ubi->leb_size < UBI_VTBL_RECORD_SIZE) {
+		ubi_err(ubi, "LEB size too small for a volume record");
+		return -EINVAL;
+	}
+
 	ubi->vtbl_slots = ubi->leb_size / UBI_VTBL_RECORD_SIZE;
 	if (ubi->vtbl_slots > UBI_MAX_VOLUMES)
 		ubi->vtbl_slots = UBI_MAX_VOLUMES;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/mtd/ubi/wl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/mtd/ubi/wl.c
@@ -575,7 +575,7 @@
  * @vol_id: the volume ID that last used this PEB
  * @lnum: the last used logical eraseblock number for the PEB
  * @torture: if the physical eraseblock has to be tortured
- * @nested: denotes whether the work_sem is already held in read mode
+ * @nested: denotes whether the work_sem is already held
  *
  * This function returns zero in case of success and a %-ENOMEM in case of
  * failure.
@@ -689,16 +689,16 @@
 
 #ifdef CONFIG_MTD_UBI_FASTMAP
 	e1 = find_anchor_wl_entry(&ubi->used);
-	if (e1 && ubi->fm_next_anchor &&
-	    (ubi->fm_next_anchor->ec - e1->ec >= UBI_WL_THRESHOLD)) {
+	if (e1 && ubi->fm_anchor &&
+	    (ubi->fm_anchor->ec - e1->ec >= UBI_WL_THRESHOLD)) {
 		ubi->fm_do_produce_anchor = 1;
-		/* fm_next_anchor is no longer considered a good anchor
-		 * candidate.
+		/*
+		 * fm_anchor is no longer considered a good anchor.
 		 * NULL assignment also prevents multiple wear level checks
 		 * of this PEB.
 		 */
-		wl_tree_add(ubi->fm_next_anchor, &ubi->free);
-		ubi->fm_next_anchor = NULL;
+		wl_tree_add(ubi->fm_anchor, &ubi->free);
+		ubi->fm_anchor = NULL;
 		ubi->free_count++;
 	}
 
@@ -830,7 +830,14 @@
 			goto out_not_moved;
 		}
 		if (err == MOVE_RETRY) {
-			scrubbing = 1;
+			/*
+			 * For source PEB:
+			 * 1. The scrubbing is set for scrub type PEB, it will
+			 *    be put back into ubi->scrub list.
+			 * 2. Non-scrub type PEB will be put back into ubi->used
+			 *    list.
+			 */
+			keep = 1;
 			dst_leb_clean = 1;
 			goto out_not_moved;
 		}
@@ -886,8 +893,11 @@
 
 	err = do_sync_erase(ubi, e1, vol_id, lnum, 0);
 	if (err) {
-		if (e2)
+		if (e2) {
+			spin_lock(&ubi->wl_lock);
 			wl_entry_destroy(ubi, e2);
+			spin_unlock(&ubi->wl_lock);
+		}
 		goto out_ro;
 	}
 
@@ -969,11 +979,11 @@
 	spin_lock(&ubi->wl_lock);
 	ubi->move_from = ubi->move_to = NULL;
 	ubi->move_to_put = ubi->wl_scheduled = 0;
+	wl_entry_destroy(ubi, e1);
+	wl_entry_destroy(ubi, e2);
 	spin_unlock(&ubi->wl_lock);
 
 	ubi_free_vid_buf(vidb);
-	wl_entry_destroy(ubi, e1);
-	wl_entry_destroy(ubi, e2);
 
 out_ro:
 	ubi_ro_mode(ubi);
@@ -1085,12 +1095,13 @@
 	if (!err) {
 		spin_lock(&ubi->wl_lock);
 
-		if (!ubi->fm_disabled && !ubi->fm_next_anchor &&
+		if (!ubi->fm_disabled && !ubi->fm_anchor &&
 		    e->pnum < UBI_FM_MAX_START) {
-			/* Abort anchor production, if needed it will be
+			/*
+			 * Abort anchor production, if needed it will be
 			 * enabled again in the wear leveling started below.
 			 */
-			ubi->fm_next_anchor = e;
+			ubi->fm_anchor = e;
 			ubi->fm_do_produce_anchor = 0;
 		} else {
 			wl_tree_add(e, &ubi->free);
@@ -1117,16 +1128,20 @@
 		int err1;
 
 		/* Re-schedule the LEB for erasure */
-		err1 = schedule_erase(ubi, e, vol_id, lnum, 0, false);
+		err1 = schedule_erase(ubi, e, vol_id, lnum, 0, true);
 		if (err1) {
+			spin_lock(&ubi->wl_lock);
 			wl_entry_destroy(ubi, e);
+			spin_unlock(&ubi->wl_lock);
 			err = err1;
 			goto out_ro;
 		}
 		return err;
 	}
 
+	spin_lock(&ubi->wl_lock);
 	wl_entry_destroy(ubi, e);
+	spin_unlock(&ubi->wl_lock);
 	if (err != -EIO)
 		/*
 		 * If this is not %-EIO, we have no idea what to do. Scheduling
@@ -1242,6 +1257,18 @@
 retry:
 	spin_lock(&ubi->wl_lock);
 	e = ubi->lookuptbl[pnum];
+	if (!e) {
+		/*
+		 * This wl entry has been removed for some errors by other
+		 * process (eg. wear leveling worker), corresponding process
+		 * (except __erase_worker, which cannot concurrent with
+		 * ubi_wl_put_peb) will set ubi ro_mode at the same time,
+		 * just ignore this wl entry.
+		 */
+		spin_unlock(&ubi->wl_lock);
+		up_read(&ubi->fm_protect);
+		return 0;
+	}
 	if (e == ubi->move_from) {
 		/*
 		 * User is putting the physical eraseblock which was selected to
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/Kconfig
@@ -81,7 +81,6 @@
 	select CRYPTO
 	select CRYPTO_LIB_CURVE25519
 	select CRYPTO_LIB_CHACHA20POLY1305
-	select CRYPTO_LIB_BLAKE2S
 	select CRYPTO_CHACHA20_X86_64 if X86 && 64BIT
 	select CRYPTO_POLY1305_X86_64 if X86 && 64BIT
 	select CRYPTO_BLAKE2S_X86 if X86 && 64BIT
@@ -150,7 +149,7 @@
 
 config IFB
 	tristate "Intermediate Functional Block support"
-	depends on NET_CLS_ACT
+	depends on NET_ACT_MIRRED || NFT_FWD_NETDEV
 	select NET_REDIRECT
 	help
 	  This is an intermediate driver that allows sharing of
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/Makefile
@@ -30,7 +30,7 @@
 obj-$(CONFIG_TAP) += tap.o
 obj-$(CONFIG_VETH) += veth.o
 obj-$(CONFIG_VIRTIO_NET) += virtio_net.o
-obj-$(CONFIG_VXLAN) += vxlan.o
+obj-$(CONFIG_VXLAN) += vxlan/
 obj-$(CONFIG_GENEVE) += geneve.o
 obj-$(CONFIG_BAREUDP) += bareudp.o
 obj-$(CONFIG_GTP) += gtp.o
@@ -46,7 +46,9 @@
 obj-$(CONFIG_DEV_APPLETALK) += appletalk/
 obj-$(CONFIG_CAIF) += caif/
 obj-$(CONFIG_CAN) += can/
-obj-$(CONFIG_NET_DSA) += dsa/
+ifdef CONFIG_NET_DSA
+obj-y += dsa/
+endif
 obj-$(CONFIG_ETHERNET) += ethernet/
 obj-$(CONFIG_FDDI) += fddi/
 obj-$(CONFIG_HIPPI) += hippi/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/arcnet/arcdevice.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/arcnet/arcdevice.h
@@ -186,6 +186,8 @@
 #define ARC_IS_5MBIT    1   /* card default speed is 5MBit */
 #define ARC_CAN_10MBIT  2   /* card uses COM20022, supporting 10MBit,
 				 but default is 2.5MBit. */
+#define ARC_HAS_LED     4   /* card has software controlled LEDs */
+#define ARC_HAS_ROTARY  8   /* card has rotary encoder */
 
 /* information needed to define an encapsulation driver */
 struct ArcProto {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/arcnet/arcnet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/arcnet/arcnet.c
@@ -468,7 +468,7 @@
 
 	ret = sock_queue_err_skb(sk, ackskb);
 	if (ret)
-		kfree_skb(ackskb);
+		dev_kfree_skb_irq(ackskb);
 
 	local_irq_enable();
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/arcnet/com20020-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/arcnet/com20020-pci.c
@@ -138,6 +138,9 @@
 		return -ENOMEM;
 
 	ci = (struct com20020_pci_card_info *)id->driver_data;
+	if (!ci)
+		return -EINVAL;
+
 	priv->ci = ci;
 	mm = &ci->misc_map;
 
@@ -210,12 +213,13 @@
 		if (!strncmp(ci->name, "EAE PLX-PCI FB2", 15))
 			lp->backplane = 1;
 
-		/* Get the dev_id from the PLX rotary coder */
-		if (!strncmp(ci->name, "EAE PLX-PCI MA1", 15))
-			dev_id_mask = 0x3;
-		dev->dev_id = (inb(priv->misc + ci->rotary) >> 4) & dev_id_mask;
-
-		snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);
+		if (ci->flags & ARC_HAS_ROTARY) {
+			/* Get the dev_id from the PLX rotary coder */
+			if (!strncmp(ci->name, "EAE PLX-PCI MA1", 15))
+				dev_id_mask = 0x3;
+			dev->dev_id = (inb(priv->misc + ci->rotary) >> 4) & dev_id_mask;
+			snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);
+		}
 
 		if (arcnet_inb(ioaddr, COM20020_REG_R_STATUS) == 0xFF) {
 			pr_err("IO address %Xh is empty!\n", ioaddr);
@@ -227,6 +231,10 @@
 			goto err_free_arcdev;
 		}
 
+		ret = com20020_found(dev, IRQF_SHARED);
+		if (ret)
+			goto err_free_arcdev;
+
 		card = devm_kzalloc(&pdev->dev, sizeof(struct com20020_dev),
 				    GFP_KERNEL);
 		if (!card) {
@@ -236,41 +244,54 @@
 
 		card->index = i;
 		card->pci_priv = priv;
-		card->tx_led.brightness_set = led_tx_set;
-		card->tx_led.default_trigger = devm_kasprintf(&pdev->dev,
-						GFP_KERNEL, "arc%d-%d-tx",
-						dev->dev_id, i);
-		card->tx_led.name = devm_kasprintf(&pdev->dev, GFP_KERNEL,
-						"pci:green:tx:%d-%d",
-						dev->dev_id, i);
-
-		card->tx_led.dev = &dev->dev;
-		card->recon_led.brightness_set = led_recon_set;
-		card->recon_led.default_trigger = devm_kasprintf(&pdev->dev,
-						GFP_KERNEL, "arc%d-%d-recon",
-						dev->dev_id, i);
-		card->recon_led.name = devm_kasprintf(&pdev->dev, GFP_KERNEL,
-						"pci:red:recon:%d-%d",
-						dev->dev_id, i);
-		card->recon_led.dev = &dev->dev;
-		card->dev = dev;
 
-		ret = devm_led_classdev_register(&pdev->dev, &card->tx_led);
-		if (ret)
-			goto err_free_arcdev;
+		if (ci->flags & ARC_HAS_LED) {
+			card->tx_led.brightness_set = led_tx_set;
+			card->tx_led.default_trigger = devm_kasprintf(&pdev->dev,
+							GFP_KERNEL, "arc%d-%d-tx",
+							dev->dev_id, i);
+			if (!card->tx_led.default_trigger) {
+				ret = -ENOMEM;
+				goto err_free_arcdev;
+			}
+			card->tx_led.name = devm_kasprintf(&pdev->dev, GFP_KERNEL,
+							"pci:green:tx:%d-%d",
+							dev->dev_id, i);
+			if (!card->tx_led.name) {
+				ret = -ENOMEM;
+				goto err_free_arcdev;
+			}
+			card->tx_led.dev = &dev->dev;
+			card->recon_led.brightness_set = led_recon_set;
+			card->recon_led.default_trigger = devm_kasprintf(&pdev->dev,
+							GFP_KERNEL, "arc%d-%d-recon",
+							dev->dev_id, i);
+			if (!card->recon_led.default_trigger) {
+				ret = -ENOMEM;
+				goto err_free_arcdev;
+			}
+			card->recon_led.name = devm_kasprintf(&pdev->dev, GFP_KERNEL,
+							"pci:red:recon:%d-%d",
+							dev->dev_id, i);
+			if (!card->recon_led.name) {
+				ret = -ENOMEM;
+				goto err_free_arcdev;
+			}
+			card->recon_led.dev = &dev->dev;
+
+			ret = devm_led_classdev_register(&pdev->dev, &card->tx_led);
+			if (ret)
+				goto err_free_arcdev;
+
+			ret = devm_led_classdev_register(&pdev->dev, &card->recon_led);
+			if (ret)
+				goto err_free_arcdev;
 
-		ret = devm_led_classdev_register(&pdev->dev, &card->recon_led);
-		if (ret)
-			goto err_free_arcdev;
-
-		dev_set_drvdata(&dev->dev, card);
-
-		ret = com20020_found(dev, IRQF_SHARED);
-		if (ret)
-			goto err_free_arcdev;
-
-		devm_arcnet_led_init(dev, dev->dev_id, i);
+			dev_set_drvdata(&dev->dev, card);
+			devm_arcnet_led_init(dev, dev->dev_id, i);
+		}
 
+		card->dev = dev;
 		list_add(&card->list, &priv->list_dev);
 		continue;
 
@@ -326,7 +347,7 @@
 };
 
 static struct com20020_pci_card_info card_info_sohard = {
-	.name = "PLX-PCI",
+	.name = "SOHARD SH ARC-PCI",
 	.devcount = 1,
 	/* SOHARD needs PCI base addr 4 */
 	.chan_map_tbl = {
@@ -361,7 +382,7 @@
 		},
 	},
 	.rotary = 0x0,
-	.flags = ARC_CAN_10MBIT,
+	.flags = ARC_HAS_ROTARY | ARC_HAS_LED | ARC_CAN_10MBIT,
 };
 
 static struct com20020_pci_card_info card_info_eae_ma1 = {
@@ -393,7 +414,7 @@
 		},
 	},
 	.rotary = 0x0,
-	.flags = ARC_CAN_10MBIT,
+	.flags = ARC_HAS_ROTARY | ARC_HAS_LED | ARC_CAN_10MBIT,
 };
 
 static struct com20020_pci_card_info card_info_eae_fb2 = {
@@ -418,7 +439,7 @@
 		},
 	},
 	.rotary = 0x0,
-	.flags = ARC_CAN_10MBIT,
+	.flags = ARC_HAS_ROTARY | ARC_HAS_LED | ARC_CAN_10MBIT,
 };
 
 static const struct pci_device_id com20020pci_id_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/arcnet/com20020_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/arcnet/com20020_cs.c
@@ -113,6 +113,7 @@
 	struct com20020_dev *info;
 	struct net_device *dev;
 	struct arcnet_local *lp;
+	int ret = -ENOMEM;
 
 	dev_dbg(&p_dev->dev, "com20020_attach()\n");
 
@@ -142,12 +143,18 @@
 	info->dev = dev;
 	p_dev->priv = info;
 
-	return com20020_config(p_dev);
+	ret = com20020_config(p_dev);
+	if (ret)
+		goto fail_config;
 
+	return 0;
+
+fail_config:
+	free_arcdev(dev);
 fail_alloc_dev:
 	kfree(info);
 fail_alloc_info:
-	return -ENOMEM;
+	return ret;
 } /* com20020_attach */
 
 static void com20020_detach(struct pcmcia_device *link)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bareudp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bareudp.c
@@ -60,6 +60,7 @@
 	__be16 proto;
 	void *oiph;
 	int err;
+	int nh;
 
 	bareudp = rcu_dereference_sk_user_data(sk);
 	if (!bareudp)
@@ -75,7 +76,7 @@
 
 		if (skb_copy_bits(skb, BAREUDP_BASE_HLEN, &ipversion,
 				  sizeof(ipversion))) {
-			bareudp->dev->stats.rx_dropped++;
+			DEV_STATS_INC(bareudp->dev, rx_dropped);
 			goto drop;
 		}
 		ipversion >>= 4;
@@ -85,7 +86,7 @@
 		} else if (ipversion == 6 && bareudp->multi_proto_mode) {
 			proto = htons(ETH_P_IPV6);
 		} else {
-			bareudp->dev->stats.rx_dropped++;
+			DEV_STATS_INC(bareudp->dev, rx_dropped);
 			goto drop;
 		}
 	} else if (bareudp->ethertype == htons(ETH_P_MPLS_UC)) {
@@ -99,7 +100,7 @@
 				   ipv4_is_multicast(tunnel_hdr->daddr)) {
 				proto = htons(ETH_P_MPLS_MC);
 			} else {
-				bareudp->dev->stats.rx_dropped++;
+				DEV_STATS_INC(bareudp->dev, rx_dropped);
 				goto drop;
 			}
 		} else {
@@ -115,7 +116,7 @@
 				   (addr_type & IPV6_ADDR_MULTICAST)) {
 				proto = htons(ETH_P_MPLS_MC);
 			} else {
-				bareudp->dev->stats.rx_dropped++;
+				DEV_STATS_INC(bareudp->dev, rx_dropped);
 				goto drop;
 			}
 		}
@@ -127,28 +128,43 @@
 				 proto,
 				 !net_eq(bareudp->net,
 				 dev_net(bareudp->dev)))) {
-		bareudp->dev->stats.rx_dropped++;
+		DEV_STATS_INC(bareudp->dev, rx_dropped);
 		goto drop;
 	}
 	tun_dst = udp_tun_rx_dst(skb, family, TUNNEL_KEY, 0, 0);
 	if (!tun_dst) {
-		bareudp->dev->stats.rx_dropped++;
+		DEV_STATS_INC(bareudp->dev, rx_dropped);
 		goto drop;
 	}
 	skb_dst_set(skb, &tun_dst->dst);
 	skb->dev = bareudp->dev;
-	oiph = skb_network_header(skb);
-	skb_reset_network_header(skb);
 	skb_reset_mac_header(skb);
 
-	if (!IS_ENABLED(CONFIG_IPV6) || family == AF_INET)
+	/* Save offset of outer header relative to skb->head,
+	 * because we are going to reset the network header to the inner header
+	 * and might change skb->head.
+	 */
+	nh = skb_network_header(skb) - skb->head;
+
+	skb_reset_network_header(skb);
+
+	if (!pskb_inet_may_pull(skb)) {
+		DEV_STATS_INC(bareudp->dev, rx_length_errors);
+		DEV_STATS_INC(bareudp->dev, rx_errors);
+		goto drop;
+	}
+
+	/* Get the outer header. */
+	oiph = skb->head + nh;
+
+	if (!ipv6_mod_enabled() || family == AF_INET)
 		err = IP_ECN_decapsulate(oiph, skb);
 	else
 		err = IP6_ECN_decapsulate(oiph, skb);
 
 	if (unlikely(err)) {
 		if (log_ecn_error) {
-			if  (!IS_ENABLED(CONFIG_IPV6) || family == AF_INET)
+			if  (!ipv6_mod_enabled() || family == AF_INET)
 				net_info_ratelimited("non-ECT from %pI4 "
 						     "with TOS=%#x\n",
 						     &((struct iphdr *)oiph)->saddr,
@@ -158,8 +174,8 @@
 						     &((struct ipv6hdr *)oiph)->saddr);
 		}
 		if (err > 1) {
-			++bareudp->dev->stats.rx_frame_errors;
-			++bareudp->dev->stats.rx_errors;
+			DEV_STATS_INC(bareudp->dev, rx_frame_errors);
+			DEV_STATS_INC(bareudp->dev, rx_errors);
 			goto drop;
 		}
 	}
@@ -214,11 +230,12 @@
 	int err;
 
 	memset(&udp_conf, 0, sizeof(udp_conf));
-#if IS_ENABLED(CONFIG_IPV6)
-	udp_conf.family = AF_INET6;
-#else
-	udp_conf.family = AF_INET;
-#endif
+
+	if (ipv6_mod_enabled())
+		udp_conf.family = AF_INET6;
+	else
+		udp_conf.family = AF_INET;
+
 	udp_conf.local_udp_port = port;
 	/* Open UDP socket */
 	err = udp_sock_create(net, &udp_conf, &sock);
@@ -295,6 +312,9 @@
 	__be32 saddr;
 	int err;
 
+	if (!skb_vlan_inet_prepare(skb, skb->protocol != htons(ETH_P_TEB)))
+		return -EINVAL;
+
 	if (!sock)
 		return -ESHUTDOWN;
 
@@ -358,6 +378,9 @@
 	__be16 sport;
 	int err;
 
+	if (!skb_vlan_inet_prepare(skb, skb->protocol != htons(ETH_P_TEB)))
+		return -EINVAL;
+
 	if (!sock)
 		return -ESHUTDOWN;
 
@@ -441,7 +464,7 @@
 	}
 
 	rcu_read_lock();
-	if (IS_ENABLED(CONFIG_IPV6) && info->mode & IP_TUNNEL_INFO_IPV6)
+	if (ipv6_mod_enabled() && info->mode & IP_TUNNEL_INFO_IPV6)
 		err = bareudp6_xmit_skb(skb, dev, bareudp, info);
 	else
 		err = bareudp_xmit_skb(skb, dev, bareudp, info);
@@ -454,11 +477,11 @@
 	dev_kfree_skb(skb);
 
 	if (err == -ELOOP)
-		dev->stats.collisions++;
+		DEV_STATS_INC(dev, collisions);
 	else if (err == -ENETUNREACH)
-		dev->stats.tx_carrier_errors++;
+		DEV_STATS_INC(dev, tx_carrier_errors);
 
-	dev->stats.tx_errors++;
+	DEV_STATS_INC(dev, tx_errors);
 	return NETDEV_TX_OK;
 }
 
@@ -471,7 +494,7 @@
 
 	use_cache = ip_tunnel_dst_cache_usable(skb, info);
 
-	if (!IS_ENABLED(CONFIG_IPV6) || ip_tunnel_info_af(info) == AF_INET) {
+	if (!ipv6_mod_enabled() || ip_tunnel_info_af(info) == AF_INET) {
 		struct rtable *rt;
 		__be32 saddr;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_3ad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_3ad.c
@@ -87,8 +87,9 @@
 static u16 ad_ticks_per_sec;
 static const int ad_delta_in_ticks = (AD_TIMER_INTERVAL * HZ) / 1000;
 
-static const u8 lacpdu_mcast_addr[ETH_ALEN + 2] __long_aligned =
-	MULTICAST_LACPDU_ADDR;
+const u8 lacpdu_mcast_addr[ETH_ALEN + 2] __long_aligned = {
+	0x01, 0x80, 0xC2, 0x00, 0x00, 0x02
+};
 
 /* ================= main 802.3ad protocol functions ================== */
 static int ad_lacpdu_send(struct port *port);
@@ -225,7 +226,7 @@
 	if (bond == NULL)
 		return 0;
 
-	return BOND_AD_INFO(bond).agg_select_timer ? 1 : 0;
+	return atomic_read(&BOND_AD_INFO(bond).agg_select_timer) ? 1 : 0;
 }
 
 /**
@@ -1021,8 +1022,8 @@
 				if (port->aggregator &&
 				    port->aggregator->is_active &&
 				    !__port_is_enabled(port)) {
-
 					__enable_port(port);
+					*update_slave_arr = true;
 				}
 			}
 			break;
@@ -1538,6 +1539,7 @@
 			slave_err(bond->dev, port->slave->dev,
 				  "Port %d did not find a suitable aggregator\n",
 				  port->actor_port_number);
+			return;
 		}
 	}
 	/* if all aggregator's ports are READY_N == TRUE, set ready=TRUE
@@ -1779,6 +1781,7 @@
 			     port = port->next_port_in_aggregator) {
 				__enable_port(port);
 			}
+			*update_slave_arr = true;
 		}
 	}
 
@@ -1994,7 +1997,7 @@
  */
 void bond_3ad_initiate_agg_selection(struct bonding *bond, int timeout)
 {
-	BOND_AD_INFO(bond).agg_select_timer = timeout;
+	atomic_set(&BOND_AD_INFO(bond).agg_select_timer, timeout);
 }
 
 /**
@@ -2006,30 +2009,24 @@
  */
 void bond_3ad_initialize(struct bonding *bond, u16 tick_resolution)
 {
-	/* check that the bond is not initialized yet */
-	if (!MAC_ADDRESS_EQUAL(&(BOND_AD_INFO(bond).system.sys_mac_addr),
-				bond->dev->dev_addr)) {
-
-		BOND_AD_INFO(bond).aggregator_identifier = 0;
-
-		BOND_AD_INFO(bond).system.sys_priority =
-			bond->params.ad_actor_sys_prio;
-		if (is_zero_ether_addr(bond->params.ad_actor_system))
-			BOND_AD_INFO(bond).system.sys_mac_addr =
-			    *((struct mac_addr *)bond->dev->dev_addr);
-		else
-			BOND_AD_INFO(bond).system.sys_mac_addr =
-			    *((struct mac_addr *)bond->params.ad_actor_system);
+	BOND_AD_INFO(bond).aggregator_identifier = 0;
+	BOND_AD_INFO(bond).system.sys_priority =
+		bond->params.ad_actor_sys_prio;
+	if (is_zero_ether_addr(bond->params.ad_actor_system))
+		BOND_AD_INFO(bond).system.sys_mac_addr =
+		    *((struct mac_addr *)bond->dev->dev_addr);
+	else
+		BOND_AD_INFO(bond).system.sys_mac_addr =
+		    *((struct mac_addr *)bond->params.ad_actor_system);
 
-		/* initialize how many times this module is called in one
-		 * second (should be about every 100ms)
-		 */
-		ad_ticks_per_sec = tick_resolution;
+	/* initialize how many times this module is called in one
+	 * second (should be about every 100ms)
+	 */
+	ad_ticks_per_sec = tick_resolution;
 
-		bond_3ad_initiate_agg_selection(bond,
-						AD_AGGREGATOR_SELECTION_TIMER *
-						ad_ticks_per_sec);
-	}
+	bond_3ad_initiate_agg_selection(bond,
+					AD_AGGREGATOR_SELECTION_TIMER *
+					ad_ticks_per_sec);
 }
 
 /**
@@ -2227,7 +2224,8 @@
 				temp_aggregator->num_of_ports--;
 				if (__agg_active_ports(temp_aggregator) == 0) {
 					select_new_active_agg = temp_aggregator->is_active;
-					ad_clear_agg(temp_aggregator);
+					if (temp_aggregator->num_of_ports == 0)
+						ad_clear_agg(temp_aggregator);
 					if (select_new_active_agg) {
 						slave_info(bond->dev, slave->dev, "Removing an active aggregator\n");
 						/* select new active aggregator */
@@ -2278,6 +2276,28 @@
 }
 
 /**
+ * bond_agg_timer_advance - advance agg_select_timer
+ * @bond:  bonding structure
+ *
+ * Return true when agg_select_timer reaches 0.
+ */
+static bool bond_agg_timer_advance(struct bonding *bond)
+{
+	int val, nval;
+
+	while (1) {
+		val = atomic_read(&BOND_AD_INFO(bond).agg_select_timer);
+		if (!val)
+			return false;
+		nval = val - 1;
+		if (atomic_cmpxchg(&BOND_AD_INFO(bond).agg_select_timer,
+				   val, nval) == val)
+			break;
+	}
+	return nval == 0;
+}
+
+/**
  * bond_3ad_state_machine_handler - handle state machines timeout
  * @work: work context to fetch bonding struct to work on from
  *
@@ -2312,9 +2332,7 @@
 	if (!bond_has_slaves(bond))
 		goto re_arm;
 
-	/* check if agg_select_timer timer after initialize is timed out */
-	if (BOND_AD_INFO(bond).agg_select_timer &&
-	    !(--BOND_AD_INFO(bond).agg_select_timer)) {
+	if (bond_agg_timer_advance(bond)) {
 		slave = bond_first_slave_rcu(bond);
 		port = slave ? &(SLAVE_AD_INFO(slave)->port) : NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_alb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_alb.c
@@ -657,10 +657,10 @@
 		return NULL;
 	arp = (struct arp_pkt *)skb_network_header(skb);
 
-	/* Don't modify or load balance ARPs that do not originate locally
-	 * (e.g.,arrive via a bridge).
+	/* Don't modify or load balance ARPs that do not originate
+	 * from the bond itself or a VLAN directly above the bond.
 	 */
-	if (!bond_slave_has_mac_rx(bond, arp->mac_src))
+	if (!bond_slave_has_mac_rcu(bond, arp->mac_src))
 		return NULL;
 
 	if (arp->op_code == htons(ARPOP_REPLY)) {
@@ -973,7 +973,8 @@
 	if (netif_is_macvlan(upper) && !strict_match) {
 		tags = bond_verify_device_path(bond->dev, upper, 0);
 		if (IS_ERR_OR_NULL(tags))
-			BUG();
+			return -ENOMEM;
+
 		alb_send_lp_vid(slave, upper->dev_addr,
 				tags[0].vlan_proto, tags[0].vlan_id);
 		kfree(tags);
@@ -1281,12 +1282,12 @@
 		return res;
 
 	if (rlb_enabled) {
-		bond->alb_info.rlb_enabled = 1;
 		res = rlb_initialize(bond);
 		if (res) {
 			tlb_deinitialize(bond);
 			return res;
 		}
+		bond->alb_info.rlb_enabled = 1;
 	} else {
 		bond->alb_info.rlb_enabled = 0;
 	}
@@ -1502,14 +1503,14 @@
 	struct slave *slave;
 
 	if (!bond_has_slaves(bond)) {
-		bond_info->tx_rebalance_counter = 0;
+		atomic_set(&bond_info->tx_rebalance_counter, 0);
 		bond_info->lp_counter = 0;
 		goto re_arm;
 	}
 
 	rcu_read_lock();
 
-	bond_info->tx_rebalance_counter++;
+	atomic_inc(&bond_info->tx_rebalance_counter);
 	bond_info->lp_counter++;
 
 	/* send learning packets */
@@ -1531,7 +1532,7 @@
 	}
 
 	/* rebalance tx traffic */
-	if (bond_info->tx_rebalance_counter >= BOND_TLB_REBALANCE_TICKS) {
+	if (atomic_read(&bond_info->tx_rebalance_counter) >= BOND_TLB_REBALANCE_TICKS) {
 		bond_for_each_slave_rcu(bond, slave, iter) {
 			tlb_clear_slave(bond, slave, 1);
 			if (slave == rcu_access_pointer(bond->curr_active_slave)) {
@@ -1541,7 +1542,7 @@
 				bond_info->unbalanced_load = 0;
 			}
 		}
-		bond_info->tx_rebalance_counter = 0;
+		atomic_set(&bond_info->tx_rebalance_counter, 0);
 	}
 
 	if (bond_info->rlb_enabled) {
@@ -1611,7 +1612,8 @@
 	tlb_init_slave(slave);
 
 	/* order a rebalance ASAP */
-	bond->alb_info.tx_rebalance_counter = BOND_TLB_REBALANCE_TICKS;
+	atomic_set(&bond->alb_info.tx_rebalance_counter,
+		   BOND_TLB_REBALANCE_TICKS);
 
 	if (bond->alb_info.rlb_enabled)
 		bond->alb_info.rlb_rebalance = 1;
@@ -1648,7 +1650,8 @@
 			rlb_clear_slave(bond, slave);
 	} else if (link == BOND_LINK_UP) {
 		/* order a rebalance ASAP */
-		bond_info->tx_rebalance_counter = BOND_TLB_REBALANCE_TICKS;
+		atomic_set(&bond_info->tx_rebalance_counter,
+			   BOND_TLB_REBALANCE_TICKS);
 		if (bond->alb_info.rlb_enabled) {
 			bond->alb_info.rlb_rebalance = 1;
 			/* If the updelay module parameter is smaller than the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_debugfs.c
@@ -76,7 +76,7 @@
 
 	d = debugfs_rename(bonding_debug_root, bond->debug_dir,
 			   bonding_debug_root, bond->dev->name);
-	if (d) {
+	if (!IS_ERR(d)) {
 		bond->debug_dir = d;
 	} else {
 		netdev_warn(bond->dev, "failed to reregister, so just unregister old one\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_main.c
@@ -575,7 +575,6 @@
 		} else {
 			slave->dev->xfrmdev_ops->xdo_dev_state_delete(ipsec->xs);
 		}
-		ipsec->xs->xso.real_dev = NULL;
 	}
 	spin_unlock_bh(&bond->ipsec_lock);
 	rcu_read_unlock();
@@ -592,34 +591,30 @@
 	struct net_device *real_dev;
 	struct slave *curr_active;
 	struct bonding *bond;
-	int err;
+	bool ok = false;
 
 	bond = netdev_priv(bond_dev);
 	rcu_read_lock();
 	curr_active = rcu_dereference(bond->curr_active_slave);
+	if (!curr_active)
+		goto out;
 	real_dev = curr_active->dev;
 
-	if (BOND_MODE(bond) != BOND_MODE_ACTIVEBACKUP) {
-		err = false;
+	if (BOND_MODE(bond) != BOND_MODE_ACTIVEBACKUP)
 		goto out;
-	}
 
-	if (!xs->xso.real_dev) {
-		err = false;
+	if (!xs->xso.real_dev)
 		goto out;
-	}
 
 	if (!real_dev->xfrmdev_ops ||
 	    !real_dev->xfrmdev_ops->xdo_dev_offload_ok ||
-	    netif_is_bond_master(real_dev)) {
-		err = false;
+	    netif_is_bond_master(real_dev))
 		goto out;
-	}
 
-	err = real_dev->xfrmdev_ops->xdo_dev_offload_ok(skb, xs);
+	ok = real_dev->xfrmdev_ops->xdo_dev_offload_ok(skb, xs);
 out:
 	rcu_read_unlock();
-	return err;
+	return ok;
 }
 
 static const struct xfrmdev_ops bond_xfrmdev_ops = {
@@ -862,12 +857,8 @@
 	dev_uc_unsync(slave_dev, bond_dev);
 	dev_mc_unsync(slave_dev, bond_dev);
 
-	if (BOND_MODE(bond) == BOND_MODE_8023AD) {
-		/* del lacpdu mc addr from mc list */
-		u8 lacpdu_multicast[ETH_ALEN] = MULTICAST_LACPDU_ADDR;
-
-		dev_mc_del(slave_dev, lacpdu_multicast);
-	}
+	if (BOND_MODE(bond) == BOND_MODE_8023AD)
+		dev_mc_del(slave_dev, lacpdu_mcast_addr);
 }
 
 /*--------------------------- Active slave change ---------------------------*/
@@ -887,7 +878,8 @@
 		if (bond->dev->flags & IFF_ALLMULTI)
 			dev_set_allmulti(old_active->dev, -1);
 
-		bond_hw_addr_flush(bond->dev, old_active->dev);
+		if (bond->dev->flags & IFF_UP)
+			bond_hw_addr_flush(bond->dev, old_active->dev);
 	}
 
 	if (new_active) {
@@ -898,10 +890,12 @@
 		if (bond->dev->flags & IFF_ALLMULTI)
 			dev_set_allmulti(new_active->dev, 1);
 
-		netif_addr_lock_bh(bond->dev);
-		dev_uc_sync(new_active->dev, bond->dev);
-		dev_mc_sync(new_active->dev, bond->dev);
-		netif_addr_unlock_bh(bond->dev);
+		if (bond->dev->flags & IFF_UP) {
+			netif_addr_lock_bh(bond->dev);
+			dev_uc_sync(new_active->dev, bond->dev);
+			dev_mc_sync(new_active->dev, bond->dev);
+			netif_addr_unlock_bh(bond->dev);
+		}
 	}
 }
 
@@ -1088,16 +1082,10 @@
 	return bestslave;
 }
 
+/* must be called in RCU critical section or with RTNL held */
 static bool bond_should_notify_peers(struct bonding *bond)
 {
-	struct slave *slave;
-
-	rcu_read_lock();
-	slave = rcu_dereference(bond->curr_active_slave);
-	rcu_read_unlock();
-
-	netdev_dbg(bond->dev, "bond_should_notify_peers: slave %s\n",
-		   slave ? slave->dev->name : "NULL");
+	struct slave *slave = rcu_dereference_rtnl(bond->curr_active_slave);
 
 	if (!slave || !bond->send_peer_notif ||
 	    bond->send_peer_notif %
@@ -1106,6 +1094,9 @@
 	    test_bit(__LINK_STATE_LINKWATCH_PENDING, &slave->dev->state))
 		return false;
 
+	netdev_dbg(bond->dev, "bond_should_notify_peers: slave %s\n",
+		   slave ? slave->dev->name : "NULL");
+
 	return true;
 }
 
@@ -1393,6 +1384,7 @@
 
 #define BOND_VLAN_FEATURES	(NETIF_F_HW_CSUM | NETIF_F_SG | \
 				 NETIF_F_FRAGLIST | NETIF_F_GSO_SOFTWARE | \
+				 NETIF_F_GSO_ENCAP_ALL | \
 				 NETIF_F_HIGHDMA | NETIF_F_LRO)
 
 #define BOND_ENC_FEATURES	(NETIF_F_HW_CSUM | NETIF_F_SG | \
@@ -1474,6 +1466,10 @@
 static void bond_setup_by_slave(struct net_device *bond_dev,
 				struct net_device *slave_dev)
 {
+	bool was_up = !!(bond_dev->flags & IFF_UP);
+
+	dev_close(bond_dev);
+
 	bond_dev->header_ops	    = slave_dev->header_ops;
 
 	bond_dev->type		    = slave_dev->type;
@@ -1483,6 +1479,13 @@
 
 	memcpy(bond_dev->broadcast, slave_dev->broadcast,
 		slave_dev->addr_len);
+
+	if (slave_dev->flags & IFF_POINTOPOINT) {
+		bond_dev->flags &= ~(IFF_BROADCAST | IFF_MULTICAST);
+		bond_dev->flags |= (IFF_POINTOPOINT | IFF_NOARP);
+	}
+	if (was_up)
+		dev_open(bond_dev, NULL);
 }
 
 /* On bonding slaves other than the currently active slave, suppress
@@ -1745,6 +1748,20 @@
 		slave_err(bond_dev, slave_dev, "Error: %s\n", errmsg);	\
 } while (0)
 
+/* The bonding driver uses ether_setup() to convert a master bond device
+ * to ARPHRD_ETHER, that resets the target netdevice's flags so we always
+ * have to restore the IFF_MASTER flag, and only restore IFF_SLAVE and IFF_UP
+ * if they were set
+ */
+static void bond_ether_setup(struct net_device *bond_dev)
+{
+	unsigned int flags = bond_dev->flags & (IFF_SLAVE | IFF_UP);
+
+	ether_setup(bond_dev);
+	bond_dev->flags |= IFF_MASTER | flags;
+	bond_dev->priv_flags &= ~IFF_TX_SKB_SHARING;
+}
+
 /* enslave device <slave> to bond device <master> */
 int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev,
 		 struct netlink_ext_ack *extack)
@@ -1836,10 +1853,8 @@
 
 			if (slave_dev->type != ARPHRD_ETHER)
 				bond_setup_by_slave(bond_dev, slave_dev);
-			else {
-				ether_setup(bond_dev);
-				bond_dev->priv_flags &= ~IFF_TX_SKB_SHARING;
-			}
+			else
+				bond_ether_setup(bond_dev);
 
 			call_netdevice_notifiers(NETDEV_POST_TYPE_CHANGE,
 						 bond_dev);
@@ -2134,16 +2149,14 @@
 			}
 		}
 
-		netif_addr_lock_bh(bond_dev);
-		dev_mc_sync_multiple(slave_dev, bond_dev);
-		dev_uc_sync_multiple(slave_dev, bond_dev);
-		netif_addr_unlock_bh(bond_dev);
-
-		if (BOND_MODE(bond) == BOND_MODE_8023AD) {
-			/* add lacpdu mc addr to mc list */
-			u8 lacpdu_multicast[ETH_ALEN] = MULTICAST_LACPDU_ADDR;
+		if (bond_dev->flags & IFF_UP) {
+			netif_addr_lock_bh(bond_dev);
+			dev_mc_sync_multiple(slave_dev, bond_dev);
+			dev_uc_sync_multiple(slave_dev, bond_dev);
+			netif_addr_unlock_bh(bond_dev);
 
-			dev_mc_add(slave_dev, lacpdu_multicast);
+			if (BOND_MODE(bond) == BOND_MODE_8023AD)
+				dev_mc_add(slave_dev, lacpdu_mcast_addr);
 		}
 	}
 
@@ -2259,9 +2272,7 @@
 			eth_hw_addr_random(bond_dev);
 		if (bond_dev->type != ARPHRD_ETHER) {
 			dev_close(bond_dev);
-			ether_setup(bond_dev);
-			bond_dev->flags |= IFF_MASTER;
-			bond_dev->priv_flags &= ~IFF_TX_SKB_SHARING;
+			bond_ether_setup(bond_dev);
 		}
 	}
 
@@ -2377,10 +2388,9 @@
 		bond_select_active_slave(bond);
 	}
 
-	if (!bond_has_slaves(bond)) {
-		bond_set_carrier(bond);
+	bond_set_carrier(bond);
+	if (!bond_has_slaves(bond))
 		eth_hw_addr_random(bond_dev);
-	}
 
 	unblock_netpoll_tx();
 	synchronize_rcu();
@@ -2416,7 +2426,8 @@
 		if (old_flags & IFF_ALLMULTI)
 			dev_set_allmulti(slave_dev, -1);
 
-		bond_hw_addr_flush(bond_dev, slave_dev);
+		if (old_flags & IFF_UP)
+			bond_hw_addr_flush(bond_dev, slave_dev);
 	}
 
 	slave_disable_netpoll(slave);
@@ -2502,12 +2513,21 @@
 /* called with rcu_read_lock() */
 static int bond_miimon_inspect(struct bonding *bond)
 {
+	bool ignore_updelay = false;
 	int link_state, commit = 0;
 	struct list_head *iter;
 	struct slave *slave;
-	bool ignore_updelay;
 
-	ignore_updelay = !rcu_dereference(bond->curr_active_slave);
+	if (BOND_MODE(bond) == BOND_MODE_ACTIVEBACKUP) {
+		ignore_updelay = !rcu_dereference(bond->curr_active_slave);
+	} else {
+		struct bond_up_slave *usable_slaves;
+
+		usable_slaves = rcu_dereference(bond->usable_slaves);
+
+		if (usable_slaves && usable_slaves->count == 0)
+			ignore_updelay = true;
+	}
 
 	bond_for_each_slave_rcu(bond, slave, iter) {
 		bond_propose_link_state(slave, BOND_LINK_NOCHANGE);
@@ -3129,8 +3149,8 @@
 			 * when the source ip is 0, so don't take the link down
 			 * if we don't know our ip yet
 			 */
-			if (!bond_time_in_interval(bond, trans_start, 2) ||
-			    !bond_time_in_interval(bond, slave->last_rx, 2)) {
+			if (!bond_time_in_interval(bond, trans_start, bond->params.missed_max) ||
+			    !bond_time_in_interval(bond, slave->last_rx, bond->params.missed_max)) {
 
 				bond_propose_link_state(slave, BOND_LINK_DOWN);
 				slave_state_changed = 1;
@@ -3224,7 +3244,7 @@
 
 		/* Backup slave is down if:
 		 * - No current_arp_slave AND
-		 * - more than 3*delta since last receive AND
+		 * - more than (missed_max+1)*delta since last receive AND
 		 * - the bond has an IP address
 		 *
 		 * Note: a non-null current_arp_slave indicates
@@ -3236,20 +3256,20 @@
 		 */
 		if (!bond_is_active_slave(slave) &&
 		    !rcu_access_pointer(bond->current_arp_slave) &&
-		    !bond_time_in_interval(bond, last_rx, 3)) {
+		    !bond_time_in_interval(bond, last_rx, bond->params.missed_max + 1)) {
 			bond_propose_link_state(slave, BOND_LINK_DOWN);
 			commit++;
 		}
 
 		/* Active slave is down if:
-		 * - more than 2*delta since transmitting OR
-		 * - (more than 2*delta since receive AND
+		 * - more than missed_max*delta since transmitting OR
+		 * - (more than missed_max*delta since receive AND
 		 *    the bond has an IP address)
 		 */
 		trans_start = dev_trans_start(slave->dev);
 		if (bond_is_active_slave(slave) &&
-		    (!bond_time_in_interval(bond, trans_start, 2) ||
-		     !bond_time_in_interval(bond, last_rx, 2))) {
+		    (!bond_time_in_interval(bond, trans_start, bond->params.missed_max) ||
+		     !bond_time_in_interval(bond, last_rx, bond->params.missed_max))) {
 			bond_propose_link_state(slave, BOND_LINK_DOWN);
 			commit++;
 		}
@@ -3475,9 +3495,11 @@
 		if (!rtnl_trylock())
 			return;
 
-		if (should_notify_peers)
+		if (should_notify_peers) {
+			bond->send_peer_notif--;
 			call_netdevice_notifiers(NETDEV_NOTIFY_PEERS,
 						 bond->dev);
+		}
 		if (should_notify_rtnl) {
 			bond_slave_state_notify(bond);
 			bond_slave_link_notify(bond);
@@ -3635,7 +3657,11 @@
 		unblock_netpoll_tx();
 		break;
 	case NETDEV_FEAT_CHANGE:
-		bond_compute_features(bond);
+		if (!bond->notifier_ctx) {
+			bond->notifier_ctx = true;
+			bond_compute_features(bond);
+			bond->notifier_ctx = false;
+		}
 		break;
 	case NETDEV_RESEND_IGMP:
 		/* Propagate to master device */
@@ -3695,7 +3721,7 @@
 	if (likely(n <= hlen))
 		return data;
 	else if (skb && likely(pskb_may_pull(skb, n)))
-		return skb->head;
+		return skb->data;
 
 	return NULL;
 }
@@ -3818,14 +3844,19 @@
 	return true;
 }
 
-static u32 bond_ip_hash(u32 hash, struct flow_keys *flow)
+static u32 bond_ip_hash(u32 hash, struct flow_keys *flow, int xmit_policy)
 {
 	hash ^= (__force u32)flow_get_u32_dst(flow) ^
 		(__force u32)flow_get_u32_src(flow);
 	hash ^= (hash >> 16);
 	hash ^= (hash >> 8);
+
 	/* discard lowest hash bit to deal with the common even ports pattern */
-	return hash >> 1;
+	if (xmit_policy == BOND_XMIT_POLICY_LAYER34 ||
+		xmit_policy == BOND_XMIT_POLICY_ENCAP34)
+		return hash >> 1;
+
+	return hash;
 }
 
 /* Generate hash based on xmit policy. If @skb is given it is used to linearize
@@ -3855,7 +3886,7 @@
 			memcpy(&hash, &flow.ports.ports, sizeof(hash));
 	}
 
-	return bond_ip_hash(hash, &flow);
+	return bond_ip_hash(hash, &flow, bond->params.xmit_policy);
 }
 
 /**
@@ -3872,8 +3903,8 @@
 	    skb->l4_hash)
 		return skb->hash;
 
-	return __bond_xmit_hash(bond, skb, skb->head, skb->protocol,
-				skb->mac_header, skb->network_header,
+	return __bond_xmit_hash(bond, skb, skb->data, skb->protocol,
+				0, skb_network_offset(skb),
 				skb_headlen(skb));
 }
 
@@ -3926,6 +3957,12 @@
 	struct list_head *iter;
 	struct slave *slave;
 
+	if (BOND_MODE(bond) == BOND_MODE_ROUNDROBIN && !bond->rr_tx_counter) {
+		bond->rr_tx_counter = alloc_percpu(u32);
+		if (!bond->rr_tx_counter)
+			return -ENOMEM;
+	}
+
 	/* reset slave->backup and slave->inactive */
 	if (bond_has_slaves(bond)) {
 		bond_for_each_slave(bond, slave, iter) {
@@ -3963,6 +4000,9 @@
 		/* register to receive LACPDUs */
 		bond->recv_probe = bond_3ad_lacpdu_recv;
 		bond_3ad_initiate_agg_selection(bond, 1);
+
+		bond_for_each_slave(bond, slave, iter)
+			dev_mc_add(slave->dev, lacpdu_mcast_addr);
 	}
 
 	if (bond_mode_can_use_xmit_hash(bond))
@@ -3974,6 +4014,7 @@
 static int bond_close(struct net_device *bond_dev)
 {
 	struct bonding *bond = netdev_priv(bond_dev);
+	struct slave *slave;
 
 	bond_work_cancel_all(bond);
 	bond->send_peer_notif = 0;
@@ -3981,6 +4022,19 @@
 		bond_alb_deinitialize(bond);
 	bond->recv_probe = NULL;
 
+	if (bond_uses_primary(bond)) {
+		rcu_read_lock();
+		slave = rcu_dereference(bond->curr_active_slave);
+		if (slave)
+			bond_hw_addr_flush(bond_dev, slave->dev);
+		rcu_read_unlock();
+	} else {
+		struct list_head *iter;
+
+		bond_for_each_slave(bond, slave, iter)
+			bond_hw_addr_flush(bond_dev, slave->dev);
+	}
+
 	return 0;
 }
 
@@ -4843,25 +4897,39 @@
 	struct bonding *bond = netdev_priv(bond_dev);
 	struct slave *slave = NULL;
 	struct list_head *iter;
+	bool xmit_suc = false;
+	bool skb_used = false;
 
 	bond_for_each_slave_rcu(bond, slave, iter) {
-		if (bond_is_last_slave(bond, slave))
-			break;
-		if (bond_slave_is_up(slave) && slave->link == BOND_LINK_UP) {
-			struct sk_buff *skb2 = skb_clone(skb, GFP_ATOMIC);
+		struct sk_buff *skb2;
 
+		if (!(bond_slave_is_up(slave) && slave->link == BOND_LINK_UP))
+			continue;
+
+		if (bond_is_last_slave(bond, slave)) {
+			skb2 = skb;
+			skb_used = true;
+		} else {
+			skb2 = skb_clone(skb, GFP_ATOMIC);
 			if (!skb2) {
 				net_err_ratelimited("%s: Error: %s: skb_clone() failed\n",
 						    bond_dev->name, __func__);
 				continue;
 			}
-			bond_dev_queue_xmit(bond, skb2, slave->dev);
 		}
+
+		if (bond_dev_queue_xmit(bond, skb2, slave->dev) == NETDEV_TX_OK)
+			xmit_suc = true;
 	}
-	if (slave && bond_slave_is_up(slave) && slave->link == BOND_LINK_UP)
-		return bond_dev_queue_xmit(bond, skb, slave->dev);
 
-	return bond_tx_drop(bond_dev, skb);
+	if (!skb_used)
+		dev_kfree_skb_any(skb);
+
+	if (xmit_suc)
+		return NETDEV_TX_OK;
+
+	atomic_long_inc(&bond_dev->tx_dropped);
+	return NET_XMIT_DROP;
 }
 
 /*------------------------- Device initialization ---------------------------*/
@@ -4999,7 +5067,7 @@
 	/* L4 */
 	memcpy(&hash, &flow.ports.ports, sizeof(hash));
 	/* L3 */
-	return bond_ip_hash(hash, &flow);
+	return bond_ip_hash(hash, &flow, BOND_XMIT_POLICY_LAYER34);
 }
 
 static struct net_device *__bond_sk_get_lower_dev(struct bonding *bond,
@@ -5124,9 +5192,9 @@
 		break;
 
 	default:
-		/* Should never happen. Mode guarded by bond_xdp_check() */
-		netdev_err(bond_dev, "Unknown bonding mode %d for xdp xmit\n", BOND_MODE(bond));
-		WARN_ON_ONCE(1);
+		if (net_ratelimit())
+			netdev_err(bond_dev, "Unknown bonding mode %d for xdp xmit\n",
+				   BOND_MODE(bond));
 		return NULL;
 	}
 
@@ -5422,7 +5490,9 @@
 
 	bond_dev->hw_features = BOND_VLAN_FEATURES |
 				NETIF_F_HW_VLAN_CTAG_RX |
-				NETIF_F_HW_VLAN_CTAG_FILTER;
+				NETIF_F_HW_VLAN_CTAG_FILTER |
+				NETIF_F_HW_VLAN_STAG_RX |
+				NETIF_F_HW_VLAN_STAG_FILTER;
 
 	bond_dev->hw_features |= NETIF_F_GSO_ENCAP_ALL;
 	bond_dev->features |= bond_dev->hw_features;
@@ -5822,6 +5892,7 @@
 	params->arp_interval = arp_interval;
 	params->arp_validate = arp_validate_value;
 	params->arp_all_targets = arp_all_targets_value;
+	params->missed_max = 2;
 	params->updelay = updelay;
 	params->downdelay = downdelay;
 	params->peer_notif_delay = 0;
@@ -5872,14 +5943,7 @@
 	if (!bond->wq)
 		return -ENOMEM;
 
-	if (BOND_MODE(bond) == BOND_MODE_ROUNDROBIN) {
-		bond->rr_tx_counter = alloc_percpu(u32);
-		if (!bond->rr_tx_counter) {
-			destroy_workqueue(bond->wq);
-			bond->wq = NULL;
-			return -ENOMEM;
-		}
-	}
+	bond->notifier_ctx = false;
 
 	spin_lock_init(&bond->stats_lock);
 	netdev_lockdep_set_classes(bond_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_netlink.c
@@ -79,6 +79,11 @@
 	return -EMSGSIZE;
 }
 
+/* Limit the max delay range to 300s */
+static struct netlink_range_validation delay_range = {
+	.max = 300000,
+};
+
 static const struct nla_policy bond_policy[IFLA_BOND_MAX + 1] = {
 	[IFLA_BOND_MODE]		= { .type = NLA_U8 },
 	[IFLA_BOND_ACTIVE_SLAVE]	= { .type = NLA_U32 },
@@ -109,7 +114,8 @@
 	[IFLA_BOND_AD_ACTOR_SYSTEM]	= { .type = NLA_BINARY,
 					    .len  = ETH_ALEN },
 	[IFLA_BOND_TLB_DYNAMIC_LB]	= { .type = NLA_U8 },
-	[IFLA_BOND_PEER_NOTIF_DELAY]    = { .type = NLA_U32 },
+	[IFLA_BOND_PEER_NOTIF_DELAY]    = NLA_POLICY_FULL_RANGE(NLA_U32, &delay_range),
+	[IFLA_BOND_MISSED_MAX]		= { .type = NLA_U8 },
 };
 
 static const struct nla_policy bond_slave_policy[IFLA_BOND_SLAVE_MAX + 1] = {
@@ -453,6 +459,15 @@
 			return err;
 	}
 
+	if (data[IFLA_BOND_MISSED_MAX]) {
+		int missed_max = nla_get_u8(data[IFLA_BOND_MISSED_MAX]);
+
+		bond_opt_initval(&newval, missed_max);
+		err = __bond_opt_set(bond, BOND_OPT_MISSED_MAX, &newval);
+		if (err)
+			return err;
+	}
+
 	return 0;
 }
 
@@ -515,6 +530,7 @@
 		nla_total_size(ETH_ALEN) + /* IFLA_BOND_AD_ACTOR_SYSTEM */
 		nla_total_size(sizeof(u8)) + /* IFLA_BOND_TLB_DYNAMIC_LB */
 		nla_total_size(sizeof(u32)) +	/* IFLA_BOND_PEER_NOTIF_DELAY */
+		nla_total_size(sizeof(u8)) +	/* IFLA_BOND_MISSED_MAX */
 		0;
 }
 
@@ -650,6 +666,10 @@
 		       bond->params.tlb_dynamic_lb))
 		goto nla_put_failure;
 
+	if (nla_put_u8(skb, IFLA_BOND_MISSED_MAX,
+		       bond->params.missed_max))
+		goto nla_put_failure;
+
 	if (BOND_MODE(bond) == BOND_MODE_8023AD) {
 		struct ad_info info;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_options.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_options.c
@@ -78,6 +78,8 @@
 					   const struct bond_opt_value *newval);
 static int bond_option_ad_user_port_key_set(struct bonding *bond,
 					    const struct bond_opt_value *newval);
+static int bond_option_missed_max_set(struct bonding *bond,
+				      const struct bond_opt_value *newval);
 
 
 static const struct bond_opt_value bond_mode_tbl[] = {
@@ -163,6 +165,12 @@
 	{ NULL,      -1,  0}
 };
 
+static const struct bond_opt_value bond_peer_notif_delay_tbl[] = {
+	{ "off",     0,   0},
+	{ "maxval",  300000, BOND_VALFLAG_MAX},
+	{ NULL,      -1,  0}
+};
+
 static const struct bond_opt_value bond_primary_reselect_tbl[] = {
 	{ "always",  BOND_PRI_RESELECT_ALWAYS,  BOND_VALFLAG_DEFAULT},
 	{ "better",  BOND_PRI_RESELECT_BETTER,  0},
@@ -213,6 +221,13 @@
 	{ NULL,      -1,    0},
 };
 
+static const struct bond_opt_value bond_missed_max_tbl[] = {
+	{ "minval",	1,	BOND_VALFLAG_MIN},
+	{ "maxval",	255,	BOND_VALFLAG_MAX},
+	{ "default",	2,	BOND_VALFLAG_DEFAULT},
+	{ NULL,		-1,	0},
+};
+
 static const struct bond_option bond_opts[BOND_OPT_LAST] = {
 	[BOND_OPT_MODE] = {
 		.id = BOND_OPT_MODE,
@@ -270,6 +285,15 @@
 		.values = bond_intmax_tbl,
 		.set = bond_option_arp_interval_set
 	},
+	[BOND_OPT_MISSED_MAX] = {
+		.id = BOND_OPT_MISSED_MAX,
+		.name = "arp_missed_max",
+		.desc = "Maximum number of missed ARP interval",
+		.unsuppmodes = BIT(BOND_MODE_8023AD) | BIT(BOND_MODE_TLB) |
+			       BIT(BOND_MODE_ALB),
+		.values = bond_missed_max_tbl,
+		.set = bond_option_missed_max_set
+	},
 	[BOND_OPT_ARP_TARGETS] = {
 		.id = BOND_OPT_ARP_TARGETS,
 		.name = "arp_ip_target",
@@ -449,7 +473,7 @@
 		.id = BOND_OPT_PEER_NOTIF_DELAY,
 		.name = "peer_notif_delay",
 		.desc = "Delay between each peer notification on failover event, in milliseconds",
-		.values = bond_intmax_tbl,
+		.values = bond_peer_notif_delay_tbl,
 		.set = bond_option_peer_notif_delay_set
 	}
 };
@@ -869,7 +893,7 @@
 	/* check to see if we are clearing active */
 	if (!slave_dev) {
 		netdev_dbg(bond->dev, "Clearing current active slave\n");
-		RCU_INIT_POINTER(bond->curr_active_slave, NULL);
+		bond_change_active_slave(bond, NULL);
 		bond_select_active_slave(bond);
 	} else {
 		struct slave *old_active = rtnl_dereference(bond->curr_active_slave);
@@ -1147,9 +1171,9 @@
 	__be32 target;
 
 	if (newval->string) {
-		if (!in4_pton(newval->string+1, -1, (u8 *)&target, -1, NULL)) {
-			netdev_err(bond->dev, "invalid ARP target %pI4 specified\n",
-				   &target);
+		if (strlen(newval->string) < 1 ||
+		    !in4_pton(newval->string + 1, -1, (u8 *)&target, -1, NULL)) {
+			netdev_err(bond->dev, "invalid ARP target specified\n");
 			return ret;
 		}
 		if (newval->string[0] == '+')
@@ -1186,6 +1210,16 @@
 	return 0;
 }
 
+static int bond_option_missed_max_set(struct bonding *bond,
+				      const struct bond_opt_value *newval)
+{
+	netdev_dbg(bond->dev, "Setting missed max to %s (%llu)\n",
+		   newval->string, newval->value);
+	bond->params.missed_max = newval->value;
+
+	return 0;
+}
+
 static int bond_option_primary_set(struct bonding *bond,
 				   const struct bond_opt_value *newval)
 {
@@ -1526,7 +1560,7 @@
 		mac = (u8 *)&newval->value;
 	}
 
-	if (!is_valid_ether_addr(mac))
+	if (is_multicast_ether_addr(mac))
 		goto err;
 
 	netdev_dbg(bond->dev, "Setting ad_actor_system to %pM\n", mac);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_procfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_procfs.c
@@ -115,6 +115,8 @@
 
 		seq_printf(seq, "ARP Polling Interval (ms): %d\n",
 				bond->params.arp_interval);
+		seq_printf(seq, "ARP Missed Max: %u\n",
+				bond->params.missed_max);
 
 		seq_printf(seq, "ARP IP target/s (n.n.n.n form):");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_sysfs.c
@@ -303,6 +303,18 @@
 static DEVICE_ATTR(arp_ip_target, 0644,
 		   bonding_show_arp_targets, bonding_sysfs_store_option);
 
+/* Show the arp missed max. */
+static ssize_t bonding_show_missed_max(struct device *d,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	struct bonding *bond = to_bond(d);
+
+	return sprintf(buf, "%u\n", bond->params.missed_max);
+}
+static DEVICE_ATTR(arp_missed_max, 0644,
+		   bonding_show_missed_max, bonding_sysfs_store_option);
+
 /* Show the up and down delays. */
 static ssize_t bonding_show_downdelay(struct device *d,
 				      struct device_attribute *attr,
@@ -779,6 +791,7 @@
 	&dev_attr_ad_actor_sys_prio.attr,
 	&dev_attr_ad_actor_system.attr,
 	&dev_attr_ad_user_port_key.attr,
+	&dev_attr_arp_missed_max.attr,
 	NULL,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/bonding/bond_sysfs_slave.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/bonding/bond_sysfs_slave.c
@@ -108,15 +108,15 @@
 }
 static SLAVE_ATTR_RO(ad_partner_oper_port_state);
 
-static const struct slave_attribute *slave_attrs[] = {
-	&slave_attr_state,
-	&slave_attr_mii_status,
-	&slave_attr_link_failure_count,
-	&slave_attr_perm_hwaddr,
-	&slave_attr_queue_id,
-	&slave_attr_ad_aggregator_id,
-	&slave_attr_ad_actor_oper_port_state,
-	&slave_attr_ad_partner_oper_port_state,
+static const struct attribute *slave_attrs[] = {
+	&slave_attr_state.attr,
+	&slave_attr_mii_status.attr,
+	&slave_attr_link_failure_count.attr,
+	&slave_attr_perm_hwaddr.attr,
+	&slave_attr_queue_id.attr,
+	&slave_attr_ad_aggregator_id.attr,
+	&slave_attr_ad_actor_oper_port_state.attr,
+	&slave_attr_ad_partner_oper_port_state.attr,
 	NULL
 };
 
@@ -137,24 +137,10 @@
 
 int bond_sysfs_slave_add(struct slave *slave)
 {
-	const struct slave_attribute **a;
-	int err;
-
-	for (a = slave_attrs; *a; ++a) {
-		err = sysfs_create_file(&slave->kobj, &((*a)->attr));
-		if (err) {
-			kobject_put(&slave->kobj);
-			return err;
-		}
-	}
-
-	return 0;
+	return sysfs_create_files(&slave->kobj, slave_attrs);
 }
 
 void bond_sysfs_slave_del(struct slave *slave)
 {
-	const struct slave_attribute **a;
-
-	for (a = slave_attrs; *a; ++a)
-		sysfs_remove_file(&slave->kobj, &((*a)->attr));
+	sysfs_remove_files(&slave->kobj, slave_attrs);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/caif/caif_virtio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/caif/caif_virtio.c
@@ -721,13 +721,21 @@
 	/* Carrier is off until netdevice is opened */
 	netif_carrier_off(netdev);
 
+	/* serialize netdev register + virtio_device_ready() with ndo_open() */
+	rtnl_lock();
+
 	/* register Netdev */
-	err = register_netdev(netdev);
+	err = register_netdevice(netdev);
 	if (err) {
+		rtnl_unlock();
 		dev_err(&vdev->dev, "Unable to register netdev (%d)\n", err);
 		goto err;
 	}
 
+	virtio_device_ready(vdev);
+
+	rtnl_unlock();
+
 	debugfs_init(cfv);
 
 	return 0;
@@ -736,7 +744,7 @@
 
 	if (cfv->vr_rx)
 		vdev->vringh_config->del_vrhs(cfv->vdev);
-	if (cfv->vdev)
+	if (cfv->vq_tx)
 		vdev->config->del_vqs(cfv->vdev);
 	free_netdev(netdev);
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/at91_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/at91_can.c
@@ -553,8 +553,6 @@
 	cf->can_id |= CAN_ERR_CRTL;
 	cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_receive_skb(skb);
 }
 
@@ -779,8 +777,6 @@
 
 	at91_poll_err_frame(dev, cf, reg_sr);
 
-	dev->stats.rx_packets++;
-	dev->stats.rx_bytes += cf->len;
 	netif_receive_skb(skb);
 
 	return 1;
@@ -1037,8 +1033,6 @@
 
 	at91_irq_err_state(dev, cf, new_state);
 
-	dev->stats.rx_packets++;
-	dev->stats.rx_bytes += cf->len;
 	netif_rx(skb);
 
 	priv->can.state = new_state;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/c_can/c_can.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/c_can/c_can.h
@@ -236,9 +236,22 @@
 	return ring->tail & (ring->obj_num - 1);
 }
 
-static inline u8 c_can_get_tx_free(const struct c_can_tx_ring *ring)
+static inline u8 c_can_get_tx_free(const struct c_can_priv *priv,
+				   const struct c_can_tx_ring *ring)
 {
-	return ring->obj_num - (ring->head - ring->tail);
+	u8 head = c_can_get_tx_head(ring);
+	u8 tail = c_can_get_tx_tail(ring);
+
+	if (priv->type == BOSCH_D_CAN)
+		return ring->obj_num - (ring->head - ring->tail);
+
+	/* This is not a FIFO. C/D_CAN sends out the buffers
+	 * prioritized. The lowest buffer number wins.
+	 */
+	if (head < tail)
+		return 0;
+
+	return ring->obj_num - head;
 }
 
 #endif /* C_CAN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/c_can/c_can_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/c_can/c_can_main.c
@@ -430,7 +430,7 @@
 static bool c_can_tx_busy(const struct c_can_priv *priv,
 			  const struct c_can_tx_ring *tx_ring)
 {
-	if (c_can_get_tx_free(tx_ring) > 0)
+	if (c_can_get_tx_free(priv, tx_ring) > 0)
 		return false;
 
 	netif_stop_queue(priv->dev);
@@ -438,7 +438,7 @@
 	/* Memory barrier before checking tx_free (head and tail) */
 	smp_mb();
 
-	if (c_can_get_tx_free(tx_ring) == 0) {
+	if (c_can_get_tx_free(priv, tx_ring) == 0) {
 		netdev_dbg(priv->dev,
 			   "Stopping tx-queue (tx_head=0x%08x, tx_tail=0x%08x, len=%d).\n",
 			   tx_ring->head, tx_ring->tail,
@@ -466,7 +466,7 @@
 
 	idx = c_can_get_tx_head(tx_ring);
 	tx_ring->head++;
-	if (c_can_get_tx_free(tx_ring) == 0)
+	if (c_can_get_tx_free(priv, tx_ring) == 0)
 		netif_stop_queue(dev);
 
 	if (idx < c_can_get_tx_tail(tx_ring))
@@ -751,7 +751,7 @@
 		return;
 
 	tx_ring->tail += pkts;
-	if (c_can_get_tx_free(tx_ring)) {
+	if (c_can_get_tx_free(priv, tx_ring)) {
 		/* Make sure that anybody stopping the queue after
 		 * this sees the new tx_ring->tail.
 		 */
@@ -764,8 +764,7 @@
 	can_led_event(dev, CAN_LED_EVENT_TX);
 
 	tail = c_can_get_tx_tail(tx_ring);
-
-	if (tail == 0) {
+	if (priv->type == BOSCH_D_CAN && tail == 0) {
 		u8 head = c_can_get_tx_head(tx_ring);
 
 		/* Start transmission for all cached messages */
@@ -920,7 +919,6 @@
 	unsigned int reg_err_counter;
 	unsigned int rx_err_passive;
 	struct c_can_priv *priv = netdev_priv(dev);
-	struct net_device_stats *stats = &dev->stats;
 	struct can_frame *cf;
 	struct sk_buff *skb;
 	struct can_berr_counter bec;
@@ -996,8 +994,6 @@
 		break;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_receive_skb(skb);
 
 	return 1;
@@ -1023,49 +1019,60 @@
 
 	/* common for all type of bus errors */
 	priv->can.can_stats.bus_error++;
-	stats->rx_errors++;
 
 	/* propagate the error condition to the CAN stack */
 	skb = alloc_can_err_skb(dev, &cf);
-	if (unlikely(!skb))
-		return 0;
 
 	/* check for 'last error code' which tells us the
 	 * type of the last error to occur on the CAN bus
 	 */
-	cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+	if (likely(skb))
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
 
 	switch (lec_type) {
 	case LEC_STUFF_ERROR:
 		netdev_dbg(dev, "stuff error\n");
-		cf->data[2] |= CAN_ERR_PROT_STUFF;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_STUFF;
+		stats->rx_errors++;
 		break;
 	case LEC_FORM_ERROR:
 		netdev_dbg(dev, "form error\n");
-		cf->data[2] |= CAN_ERR_PROT_FORM;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_FORM;
+		stats->rx_errors++;
 		break;
 	case LEC_ACK_ERROR:
 		netdev_dbg(dev, "ack error\n");
-		cf->data[3] = CAN_ERR_PROT_LOC_ACK;
+		if (likely(skb))
+			cf->data[3] = CAN_ERR_PROT_LOC_ACK;
+		stats->tx_errors++;
 		break;
 	case LEC_BIT1_ERROR:
 		netdev_dbg(dev, "bit1 error\n");
-		cf->data[2] |= CAN_ERR_PROT_BIT1;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_BIT1;
+		stats->tx_errors++;
 		break;
 	case LEC_BIT0_ERROR:
 		netdev_dbg(dev, "bit0 error\n");
-		cf->data[2] |= CAN_ERR_PROT_BIT0;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_BIT0;
+		stats->tx_errors++;
 		break;
 	case LEC_CRC_ERROR:
 		netdev_dbg(dev, "CRC error\n");
-		cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ;
+		if (likely(skb))
+			cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ;
+		stats->rx_errors++;
 		break;
 	default:
 		break;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
+	if (unlikely(!skb))
+		return 0;
+
 	netif_receive_skb(skb);
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/c_can/c_can_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/c_can/c_can_platform.c
@@ -395,15 +395,16 @@
 	if (ret) {
 		dev_err(&pdev->dev, "registering %s failed (err=%d)\n",
 			KBUILD_MODNAME, ret);
-		goto exit_free_device;
+		goto exit_pm_runtime;
 	}
 
 	dev_info(&pdev->dev, "%s device registered (regs=%p, irq=%d)\n",
 		 KBUILD_MODNAME, priv->base, dev->irq);
 	return 0;
 
-exit_free_device:
+exit_pm_runtime:
 	pm_runtime_disable(priv->device);
+exit_free_device:
 	free_c_can_dev(dev);
 exit:
 	dev_err(&pdev->dev, "probe failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/cc770/cc770.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/cc770/cc770.c
@@ -499,7 +499,6 @@
 static int cc770_err(struct net_device *dev, u8 status)
 {
 	struct cc770_priv *priv = netdev_priv(dev);
-	struct net_device_stats *stats = &dev->stats;
 	struct can_frame *cf;
 	struct sk_buff *skb;
 	u8 lec;
@@ -571,8 +570,6 @@
 	}
 
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/cc770/cc770_isa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/cc770/cc770_isa.c
@@ -264,22 +264,24 @@
 	if (err) {
 		dev_err(&pdev->dev,
 			"couldn't register device (err=%d)\n", err);
-		goto exit_unmap;
+		goto exit_free;
 	}
 
 	dev_info(&pdev->dev, "device registered (reg_base=0x%p, irq=%d)\n",
 		 priv->reg_base, dev->irq);
 	return 0;
 
- exit_unmap:
+exit_free:
+	free_cc770dev(dev);
+exit_unmap:
 	if (mem[idx])
 		iounmap(base);
- exit_release:
+exit_release:
 	if (mem[idx])
 		release_mem_region(mem[idx], iosize);
 	else
 		release_region(port[idx], iosize);
- exit:
+exit:
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/dev/bittiming.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/dev/bittiming.c
@@ -209,7 +209,7 @@
 			       const struct can_bittiming_const *btc)
 {
 	struct can_priv *priv = netdev_priv(dev);
-	int tseg1, alltseg;
+	unsigned int tseg1, alltseg;
 	u64 brp64;
 
 	tseg1 = bt->prop_seg + bt->phase_seg1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/dev/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/dev/dev.c
@@ -136,12 +136,12 @@
 static void can_restart(struct net_device *dev)
 {
 	struct can_priv *priv = netdev_priv(dev);
-	struct net_device_stats *stats = &dev->stats;
 	struct sk_buff *skb;
 	struct can_frame *cf;
 	int err;
 
-	BUG_ON(netif_carrier_ok(dev));
+	if (netif_carrier_ok(dev))
+		netdev_err(dev, "Attempt to restart for bus-off recovery, but carrier is OK?\n");
 
 	/* No synchronization needed because the device is bus-off and
 	 * no messages can come in or go out.
@@ -155,9 +155,6 @@
 
 	cf->can_id |= CAN_ERR_RESTARTED;
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
-
 	netif_rx_ni(skb);
 
 restart:
@@ -165,11 +162,12 @@
 	priv->can_stats.restarts++;
 
 	/* Now restart the device */
-	err = priv->do_set_mode(dev, CAN_MODE_START);
-
 	netif_carrier_on(dev);
-	if (err)
+	err = priv->do_set_mode(dev, CAN_MODE_START);
+	if (err) {
 		netdev_err(dev, "Error %d during restart", err);
+		netif_carrier_off(dev);
+	}
 }
 
 static void can_restart_work(struct work_struct *work)
@@ -411,7 +409,7 @@
 	else
 		set = 0;
 
-	gpiod_set_value(priv->termination_gpio, set);
+	gpiod_set_value_cansleep(priv->termination_gpio, set);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/dev/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/dev/netlink.c
@@ -76,7 +76,8 @@
 		 * directly via do_set_bitrate(). Bail out if neither
 		 * is given.
 		 */
-		if (!priv->bittiming_const && !priv->do_set_bittiming)
+		if (!priv->bittiming_const && !priv->do_set_bittiming &&
+		    !priv->bitrate_const)
 			return -EOPNOTSUPP;
 
 		memcpy(&bt, nla_data(data[IFLA_CAN_BITTIMING]), sizeof(bt));
@@ -169,7 +170,8 @@
 		 * directly via do_set_bitrate(). Bail out if neither
 		 * is given.
 		 */
-		if (!priv->data_bittiming_const && !priv->do_set_data_bittiming)
+		if (!priv->data_bittiming_const && !priv->do_set_data_bittiming &&
+		    !priv->data_bitrate_const)
 			return -EOPNOTSUPP;
 
 		memcpy(&dbt, nla_data(data[IFLA_CAN_DATA_BITTIMING]),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/dev/rx-offload.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/dev/rx-offload.c
@@ -54,8 +54,10 @@
 		struct can_frame *cf = (struct can_frame *)skb->data;
 
 		work_done++;
-		stats->rx_packets++;
-		stats->rx_bytes += cf->len;
+		if (!(cf->can_id & CAN_ERR_FLAG)) {
+			stats->rx_packets++;
+			stats->rx_bytes += cf->len;
+		}
 		netif_receive_skb(skb);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/dev/skb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/dev/skb.c
@@ -42,7 +42,11 @@
 {
 	struct can_priv *priv = netdev_priv(dev);
 
-	BUG_ON(idx >= priv->echo_skb_max);
+	if (idx >= priv->echo_skb_max) {
+		netdev_err(dev, "%s: BUG! Trying to access can_priv::echo_skb out of bounds (%u/max %u)\n",
+			   __func__, idx, priv->echo_skb_max);
+		return -EINVAL;
+	}
 
 	/* check flag whether this packet has to be looped back */
 	if (!(dev->flags & IFF_ECHO) ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/flexcan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/flexcan.c
@@ -173,9 +173,9 @@
 
 /* FLEXCAN interrupt flag register (IFLAG) bits */
 /* Errata ERR005829 step7: Reserve first valid MB */
-#define FLEXCAN_TX_MB_RESERVED_OFF_FIFO		8
-#define FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP	0
-#define FLEXCAN_RX_MB_OFF_TIMESTAMP_FIRST	(FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP + 1)
+#define FLEXCAN_TX_MB_RESERVED_RX_FIFO	8
+#define FLEXCAN_TX_MB_RESERVED_RX_MAILBOX	0
+#define FLEXCAN_RX_MB_RX_MAILBOX_FIRST	(FLEXCAN_TX_MB_RESERVED_RX_MAILBOX + 1)
 #define FLEXCAN_IFLAG_MB(x)		BIT_ULL(x)
 #define FLEXCAN_IFLAG_RX_FIFO_OVERFLOW	BIT(7)
 #define FLEXCAN_IFLAG_RX_FIFO_WARN	BIT(6)
@@ -234,8 +234,8 @@
 #define FLEXCAN_QUIRK_ENABLE_EACEN_RRS  BIT(3)
 /* Disable non-correctable errors interrupt and freeze mode */
 #define FLEXCAN_QUIRK_DISABLE_MECR BIT(4)
-/* Use timestamp based offloading */
-#define FLEXCAN_QUIRK_USE_OFF_TIMESTAMP BIT(5)
+/* Use mailboxes (not FIFO) for RX path */
+#define FLEXCAN_QUIRK_USE_RX_MAILBOX BIT(5)
 /* No interrupt for error passive */
 #define FLEXCAN_QUIRK_BROKEN_PERR_STATE BIT(6)
 /* default to BE register access */
@@ -252,6 +252,12 @@
 #define FLEXCAN_QUIRK_NR_IRQ_3 BIT(12)
 /* Setup 16 mailboxes */
 #define FLEXCAN_QUIRK_NR_MB_16 BIT(13)
+/* Device supports RX via mailboxes */
+#define FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX BIT(14)
+/* Device supports RTR reception via mailboxes */
+#define FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR BIT(15)
+/* Device supports RX via FIFO */
+#define FLEXCAN_QUIRK_SUPPPORT_RX_FIFO BIT(16)
 
 /* Structure of the message buffer */
 struct flexcan_mb {
@@ -365,7 +371,7 @@
 
 	struct clk *clk_ipg;
 	struct clk *clk_per;
-	const struct flexcan_devtype_data *devtype_data;
+	struct flexcan_devtype_data devtype_data;
 	struct regulator *reg_xceiver;
 	struct flexcan_stop_mode stm;
 
@@ -382,59 +388,78 @@
 
 static const struct flexcan_devtype_data fsl_mcf5441x_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_BROKEN_PERR_STATE |
-		FLEXCAN_QUIRK_NR_IRQ_3 | FLEXCAN_QUIRK_NR_MB_16,
+		FLEXCAN_QUIRK_NR_IRQ_3 | FLEXCAN_QUIRK_NR_MB_16 |
+		FLEXCAN_QUIRK_SUPPPORT_RX_FIFO,
 };
 
 static const struct flexcan_devtype_data fsl_p1010_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_BROKEN_WERR_STATE |
 		FLEXCAN_QUIRK_BROKEN_PERR_STATE |
-		FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN,
+		FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_FIFO,
 };
 
 static const struct flexcan_devtype_data fsl_imx25_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_BROKEN_WERR_STATE |
-		FLEXCAN_QUIRK_BROKEN_PERR_STATE,
+		FLEXCAN_QUIRK_BROKEN_PERR_STATE |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_FIFO,
 };
 
 static const struct flexcan_devtype_data fsl_imx28_devtype_data = {
-	.quirks = FLEXCAN_QUIRK_BROKEN_PERR_STATE,
+	.quirks = FLEXCAN_QUIRK_BROKEN_PERR_STATE |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_FIFO,
 };
 
 static const struct flexcan_devtype_data fsl_imx6q_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
-		FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | FLEXCAN_QUIRK_BROKEN_PERR_STATE |
-		FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR,
+		FLEXCAN_QUIRK_USE_RX_MAILBOX | FLEXCAN_QUIRK_BROKEN_PERR_STATE |
+		FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR,
 };
 
 static const struct flexcan_devtype_data fsl_imx8qm_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
-		FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | FLEXCAN_QUIRK_BROKEN_PERR_STATE |
-		FLEXCAN_QUIRK_SUPPORT_FD | FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW,
+		FLEXCAN_QUIRK_USE_RX_MAILBOX | FLEXCAN_QUIRK_BROKEN_PERR_STATE |
+		FLEXCAN_QUIRK_SUPPORT_FD | FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR,
 };
 
 static struct flexcan_devtype_data fsl_imx8mp_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
-		FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_OFF_TIMESTAMP |
+		FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_RX_MAILBOX |
 		FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR |
-		FLEXCAN_QUIRK_SUPPORT_FD | FLEXCAN_QUIRK_SUPPORT_ECC,
+		FLEXCAN_QUIRK_SUPPORT_FD | FLEXCAN_QUIRK_SUPPORT_ECC |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR,
 };
 
 static const struct flexcan_devtype_data fsl_vf610_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
-		FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_OFF_TIMESTAMP |
-		FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_SUPPORT_ECC,
+		FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_RX_MAILBOX |
+		FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_SUPPORT_ECC |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR,
 };
 
 static const struct flexcan_devtype_data fsl_ls1021a_r2_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
-		FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_USE_OFF_TIMESTAMP,
+		FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_USE_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR,
 };
 
 static const struct flexcan_devtype_data fsl_lx2160a_r1_devtype_data = {
 	.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
 		FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_BROKEN_PERR_STATE |
-		FLEXCAN_QUIRK_USE_OFF_TIMESTAMP | FLEXCAN_QUIRK_SUPPORT_FD |
-		FLEXCAN_QUIRK_SUPPORT_ECC,
+		FLEXCAN_QUIRK_USE_RX_MAILBOX | FLEXCAN_QUIRK_SUPPORT_FD |
+		FLEXCAN_QUIRK_SUPPORT_ECC |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR,
 };
 
 static const struct can_bittiming_const flexcan_bittiming_const = {
@@ -596,7 +621,7 @@
 	priv->write(reg_mcr, &regs->mcr);
 
 	/* enable stop request */
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW) {
 		ret = flexcan_stop_mode_enable_scfw(priv, true);
 		if (ret < 0)
 			return ret;
@@ -615,7 +640,7 @@
 	int ret;
 
 	/* remove stop request */
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW) {
 		ret = flexcan_stop_mode_enable_scfw(priv, false);
 		if (ret < 0)
 			return ret;
@@ -1011,14 +1036,9 @@
 	u32 reg_ctrl, reg_id, reg_iflag1;
 	int i;
 
-	if (unlikely(drop)) {
-		skb = ERR_PTR(-ENOBUFS);
-		goto mark_as_read;
-	}
-
 	mb = flexcan_get_mb(priv, n);
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX) {
 		u32 code;
 
 		do {
@@ -1044,6 +1064,11 @@
 		reg_ctrl = priv->read(&mb->can_ctrl);
 	}
 
+	if (unlikely(drop)) {
+		skb = ERR_PTR(-ENOBUFS);
+		goto mark_as_read;
+	}
+
 	if (reg_ctrl & FLEXCAN_MB_CNT_EDL)
 		skb = alloc_canfd_skb(offload->dev, &cfd);
 	else
@@ -1083,7 +1108,7 @@
 	}
 
  mark_as_read:
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX)
 		flexcan_write64(priv, FLEXCAN_IFLAG_MB(n), &regs->iflag1);
 	else
 		priv->write(FLEXCAN_IFLAG_RX_FIFO_AVAILABLE, &regs->iflag1);
@@ -1109,7 +1134,7 @@
 	enum can_state last_state = priv->can.state;
 
 	/* reception interrupt */
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX) {
 		u64 reg_iflag_rx;
 		int ret;
 
@@ -1169,7 +1194,7 @@
 
 	/* state change interrupt or broken error state quirk fix is enabled */
 	if ((reg_esr & FLEXCAN_ESR_ERR_STATE) ||
-	    (priv->devtype_data->quirks & (FLEXCAN_QUIRK_BROKEN_WERR_STATE |
+	    (priv->devtype_data.quirks & (FLEXCAN_QUIRK_BROKEN_WERR_STATE |
 					   FLEXCAN_QUIRK_BROKEN_PERR_STATE)))
 		flexcan_irq_state(dev, reg_esr);
 
@@ -1191,11 +1216,11 @@
 	 * (1): enabled if FLEXCAN_QUIRK_BROKEN_WERR_STATE is enabled
 	 */
 	if ((last_state != priv->can.state) &&
-	    (priv->devtype_data->quirks & FLEXCAN_QUIRK_BROKEN_PERR_STATE) &&
+	    (priv->devtype_data.quirks & FLEXCAN_QUIRK_BROKEN_PERR_STATE) &&
 	    !(priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) {
 		switch (priv->can.state) {
 		case CAN_STATE_ERROR_ACTIVE:
-			if (priv->devtype_data->quirks &
+			if (priv->devtype_data.quirks &
 			    FLEXCAN_QUIRK_BROKEN_WERR_STATE)
 				flexcan_error_irq_enable(priv);
 			else
@@ -1423,26 +1448,26 @@
 	else
 		priv->mb_size = sizeof(struct flexcan_mb) + CAN_MAX_DLEN;
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_NR_MB_16)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_NR_MB_16)
 		priv->mb_count = 16;
 	else
 		priv->mb_count = (sizeof(priv->regs->mb[0]) / priv->mb_size) +
 				 (sizeof(priv->regs->mb[1]) / priv->mb_size);
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX)
 		priv->tx_mb_reserved =
-			flexcan_get_mb(priv, FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP);
+			flexcan_get_mb(priv, FLEXCAN_TX_MB_RESERVED_RX_MAILBOX);
 	else
 		priv->tx_mb_reserved =
-			flexcan_get_mb(priv, FLEXCAN_TX_MB_RESERVED_OFF_FIFO);
+			flexcan_get_mb(priv, FLEXCAN_TX_MB_RESERVED_RX_FIFO);
 	priv->tx_mb_idx = priv->mb_count - 1;
 	priv->tx_mb = flexcan_get_mb(priv, priv->tx_mb_idx);
 	priv->tx_mask = FLEXCAN_IFLAG_MB(priv->tx_mb_idx);
 
 	priv->offload.mailbox_read = flexcan_mailbox_read;
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) {
-		priv->offload.mb_first = FLEXCAN_RX_MB_OFF_TIMESTAMP_FIRST;
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX) {
+		priv->offload.mb_first = FLEXCAN_RX_MB_RX_MAILBOX_FIRST;
 		priv->offload.mb_last = priv->mb_count - 2;
 
 		priv->rx_mask = GENMASK_ULL(priv->offload.mb_last,
@@ -1506,7 +1531,7 @@
 	if (err)
 		goto out_chip_disable;
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SUPPORT_ECC)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SUPPORT_ECC)
 		flexcan_ram_init(dev);
 
 	flexcan_set_bittiming(dev);
@@ -1532,10 +1557,10 @@
 	/* MCR
 	 *
 	 * FIFO:
-	 * - disable for timestamp mode
+	 * - disable for mailbox mode
 	 * - enable for FIFO mode
 	 */
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX)
 		reg_mcr &= ~FLEXCAN_MCR_FEN;
 	else
 		reg_mcr |= FLEXCAN_MCR_FEN;
@@ -1586,7 +1611,7 @@
 	 * on most Flexcan cores, too. Otherwise we don't get
 	 * any error warning or passive interrupts.
 	 */
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_BROKEN_WERR_STATE ||
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_BROKEN_WERR_STATE ||
 	    priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)
 		reg_ctrl |= FLEXCAN_CTRL_ERR_MSK;
 	else
@@ -1599,7 +1624,7 @@
 	netdev_dbg(dev, "%s: writing ctrl=0x%08x", __func__, reg_ctrl);
 	priv->write(reg_ctrl, &regs->ctrl);
 
-	if ((priv->devtype_data->quirks & FLEXCAN_QUIRK_ENABLE_EACEN_RRS)) {
+	if ((priv->devtype_data.quirks & FLEXCAN_QUIRK_ENABLE_EACEN_RRS)) {
 		reg_ctrl2 = priv->read(&regs->ctrl2);
 		reg_ctrl2 |= FLEXCAN_CTRL2_EACEN | FLEXCAN_CTRL2_RRS;
 		priv->write(reg_ctrl2, &regs->ctrl2);
@@ -1631,7 +1656,7 @@
 		priv->write(reg_fdctrl, &regs->fdctrl);
 	}
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_USE_RX_MAILBOX) {
 		for (i = priv->offload.mb_first; i <= priv->offload.mb_last; i++) {
 			mb = flexcan_get_mb(priv, i);
 			priv->write(FLEXCAN_MB_CODE_RX_EMPTY,
@@ -1639,7 +1664,7 @@
 		}
 	} else {
 		/* clear and invalidate unused mailboxes first */
-		for (i = FLEXCAN_TX_MB_RESERVED_OFF_FIFO; i < priv->mb_count; i++) {
+		for (i = FLEXCAN_TX_MB_RESERVED_RX_FIFO; i < priv->mb_count; i++) {
 			mb = flexcan_get_mb(priv, i);
 			priv->write(FLEXCAN_MB_CODE_RX_INACTIVE,
 				    &mb->can_ctrl);
@@ -1659,7 +1684,7 @@
 	priv->write(0x0, &regs->rx14mask);
 	priv->write(0x0, &regs->rx15mask);
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_DISABLE_RXFG)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_DISABLE_RXFG)
 		priv->write(0x0, &regs->rxfgmask);
 
 	/* clear acceptance filters */
@@ -1673,7 +1698,7 @@
 	 * This also works around errata e5295 which generates false
 	 * positive memory errors and put the device in freeze mode.
 	 */
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_DISABLE_MECR) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_DISABLE_MECR) {
 		/* Follow the protocol as described in "Detection
 		 * and Correction of Memory Errors" to write to
 		 * MECR register (step 1 - 5)
@@ -1799,7 +1824,7 @@
 	if (err)
 		goto out_can_rx_offload_disable;
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_NR_IRQ_3) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_NR_IRQ_3) {
 		err = request_irq(priv->irq_boff,
 				  flexcan_irq, IRQF_SHARED, dev->name, dev);
 		if (err)
@@ -1845,7 +1870,7 @@
 	netif_stop_queue(dev);
 	flexcan_chip_interrupts_disable(dev);
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_NR_IRQ_3) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_NR_IRQ_3) {
 		free_irq(priv->irq_err, dev);
 		free_irq(priv->irq_boff, dev);
 	}
@@ -2051,9 +2076,9 @@
 
 	priv = netdev_priv(dev);
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW)
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW)
 		ret = flexcan_setup_stop_mode_scfw(pdev);
-	else if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR)
+	else if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR)
 		ret = flexcan_setup_stop_mode_gpr(pdev);
 	else
 		/* return 0 directly if doesn't support stop mode feature */
@@ -2164,8 +2189,25 @@
 		return -ENODEV;
 
 	if ((devtype_data->quirks & FLEXCAN_QUIRK_SUPPORT_FD) &&
-	    !(devtype_data->quirks & FLEXCAN_QUIRK_USE_OFF_TIMESTAMP)) {
-		dev_err(&pdev->dev, "CAN-FD mode doesn't work with FIFO mode!\n");
+	    !((devtype_data->quirks &
+	       (FLEXCAN_QUIRK_USE_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+		FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR |
+		FLEXCAN_QUIRK_SUPPPORT_RX_FIFO)) ==
+	      (FLEXCAN_QUIRK_USE_RX_MAILBOX |
+	       FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+	       FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR))) {
+		dev_err(&pdev->dev, "CAN-FD mode doesn't work in RX-FIFO mode!\n");
+		return -EINVAL;
+	}
+
+	if ((devtype_data->quirks &
+	     (FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX |
+	      FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR)) ==
+	    FLEXCAN_QUIRK_SUPPPORT_RX_MAILBOX_RTR) {
+		dev_err(&pdev->dev,
+			"Quirks (0x%08x) inconsistent: RX_MAILBOX_RX supported but not RX_MAILBOX\n",
+			devtype_data->quirks);
 		return -EINVAL;
 	}
 
@@ -2181,9 +2223,10 @@
 	dev->flags |= IFF_ECHO;
 
 	priv = netdev_priv(dev);
+	priv->devtype_data = *devtype_data;
 
 	if (of_property_read_bool(pdev->dev.of_node, "big-endian") ||
-	    devtype_data->quirks & FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN) {
+	    priv->devtype_data.quirks & FLEXCAN_QUIRK_DEFAULT_BIG_ENDIAN) {
 		priv->read = flexcan_read_be;
 		priv->write = flexcan_write_be;
 	} else {
@@ -2202,10 +2245,9 @@
 	priv->clk_ipg = clk_ipg;
 	priv->clk_per = clk_per;
 	priv->clk_src = clk_src;
-	priv->devtype_data = devtype_data;
 	priv->reg_xceiver = reg_xceiver;
 
-	if (devtype_data->quirks & FLEXCAN_QUIRK_NR_IRQ_3) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_NR_IRQ_3) {
 		priv->irq_boff = platform_get_irq(pdev, 1);
 		if (priv->irq_boff <= 0) {
 			err = -ENODEV;
@@ -2218,7 +2260,7 @@
 		}
 	}
 
-	if (priv->devtype_data->quirks & FLEXCAN_QUIRK_SUPPORT_FD) {
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SUPPORT_FD) {
 		priv->can.ctrlmode_supported |= CAN_CTRLMODE_FD |
 			CAN_CTRLMODE_FD_NON_ISO;
 		priv->can.bittiming_const = &flexcan_fd_bittiming_const;
@@ -2295,14 +2337,19 @@
 
 			flexcan_chip_interrupts_disable(dev);
 
+			err = flexcan_transceiver_disable(priv);
+			if (err)
+				return err;
+
 			err = pinctrl_pm_select_sleep_state(device);
 			if (err)
 				return err;
 		}
 		netif_stop_queue(dev);
 		netif_device_detach(dev);
+
+		priv->can.state = CAN_STATE_SLEEPING;
 	}
-	priv->can.state = CAN_STATE_SLEEPING;
 
 	return 0;
 }
@@ -2313,7 +2360,6 @@
 	struct flexcan_priv *priv = netdev_priv(dev);
 	int err;
 
-	priv->can.state = CAN_STATE_ERROR_ACTIVE;
 	if (netif_running(dev)) {
 		netif_device_attach(dev);
 		netif_start_queue(dev);
@@ -2327,12 +2373,20 @@
 			if (err)
 				return err;
 
-			err = flexcan_chip_start(dev);
+			err = flexcan_transceiver_enable(priv);
 			if (err)
 				return err;
 
+			err = flexcan_chip_start(dev);
+			if (err) {
+				flexcan_transceiver_disable(priv);
+				return err;
+			}
+
 			flexcan_chip_interrupts_enable(dev);
 		}
+
+		priv->can.state = CAN_STATE_ERROR_ACTIVE;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/grcan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/grcan.c
@@ -241,13 +241,14 @@
 		.rxsize		= GRCAN_DEFAULT_BUFFER_SIZE,	\
 		}
 
-#define GRCAN_TXBUG_SAFE_GRLIB_VERSION	0x4100
+#define GRCAN_TXBUG_SAFE_GRLIB_VERSION	4100
 #define GRLIB_VERSION_MASK		0xffff
 
 /* GRCAN private data structure */
 struct grcan_priv {
 	struct can_priv can;	/* must be the first member */
 	struct net_device *dev;
+	struct device *ofdev_dev;
 	struct napi_struct napi;
 
 	struct grcan_registers __iomem *regs;	/* ioremap'ed registers */
@@ -924,7 +925,7 @@
 	struct grcan_priv *priv = netdev_priv(dev);
 	struct grcan_dma *dma = &priv->dma;
 
-	dma_free_coherent(&dev->dev, dma->base_size, dma->base_buf,
+	dma_free_coherent(priv->ofdev_dev, dma->base_size, dma->base_buf,
 			  dma->base_handle);
 	memset(dma, 0, sizeof(*dma));
 }
@@ -949,7 +950,7 @@
 
 	/* Extra GRCAN_BUFFER_ALIGNMENT to allow for alignment */
 	dma->base_size = lsize + ssize + GRCAN_BUFFER_ALIGNMENT;
-	dma->base_buf = dma_alloc_coherent(&dev->dev,
+	dma->base_buf = dma_alloc_coherent(priv->ofdev_dev,
 					   dma->base_size,
 					   &dma->base_handle,
 					   GFP_KERNEL);
@@ -1113,8 +1114,10 @@
 
 	priv->closing = true;
 	if (priv->need_txbug_workaround) {
+		spin_unlock_irqrestore(&priv->lock, flags);
 		del_timer_sync(&priv->hang_timer);
 		del_timer_sync(&priv->rr_timer);
+		spin_lock_irqsave(&priv->lock, flags);
 	}
 	netif_stop_queue(dev);
 	grcan_stop_hardware(dev);
@@ -1134,7 +1137,7 @@
 	return 0;
 }
 
-static int grcan_transmit_catch_up(struct net_device *dev, int budget)
+static void grcan_transmit_catch_up(struct net_device *dev)
 {
 	struct grcan_priv *priv = netdev_priv(dev);
 	unsigned long flags;
@@ -1142,7 +1145,7 @@
 
 	spin_lock_irqsave(&priv->lock, flags);
 
-	work_done = catch_up_echo_skb(dev, budget, true);
+	work_done = catch_up_echo_skb(dev, -1, true);
 	if (work_done) {
 		if (!priv->resetting && !priv->closing &&
 		    !(priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY))
@@ -1156,8 +1159,6 @@
 	}
 
 	spin_unlock_irqrestore(&priv->lock, flags);
-
-	return work_done;
 }
 
 static int grcan_receive(struct net_device *dev, int budget)
@@ -1239,19 +1240,13 @@
 	struct net_device *dev = priv->dev;
 	struct grcan_registers __iomem *regs = priv->regs;
 	unsigned long flags;
-	int tx_work_done, rx_work_done;
-	int rx_budget = budget / 2;
-	int tx_budget = budget - rx_budget;
+	int work_done;
 
-	/* Half of the budget for receiving messages */
-	rx_work_done = grcan_receive(dev, rx_budget);
+	work_done = grcan_receive(dev, budget);
 
-	/* Half of the budget for transmitting messages as that can trigger echo
-	 * frames being received
-	 */
-	tx_work_done = grcan_transmit_catch_up(dev, tx_budget);
+	grcan_transmit_catch_up(dev);
 
-	if (rx_work_done < rx_budget && tx_work_done < tx_budget) {
+	if (work_done < budget) {
 		napi_complete(napi);
 
 		/* Guarantee no interference with a running reset that otherwise
@@ -1268,7 +1263,7 @@
 		spin_unlock_irqrestore(&priv->lock, flags);
 	}
 
-	return rx_work_done + tx_work_done;
+	return work_done;
 }
 
 /* Work tx bug by waiting while for the risky situation to clear. If that fails,
@@ -1600,6 +1595,7 @@
 	memcpy(&priv->config, &grcan_module_config,
 	       sizeof(struct grcan_device_config));
 	priv->dev = dev;
+	priv->ofdev_dev = &ofdev->dev;
 	priv->regs = base;
 	priv->can.bittiming_const = &grcan_bittiming_const;
 	priv->can.do_set_bittiming = grcan_set_bittiming;
@@ -1652,6 +1648,7 @@
 static int grcan_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
+	struct device_node *sysid_parent;
 	u32 sysid, ambafreq;
 	int irq, err;
 	void __iomem *base;
@@ -1660,10 +1657,14 @@
 	/* Compare GRLIB version number with the first that does not
 	 * have the tx bug (see start_xmit)
 	 */
-	err = of_property_read_u32(np, "systemid", &sysid);
-	if (!err && ((sysid & GRLIB_VERSION_MASK)
-		     >= GRCAN_TXBUG_SAFE_GRLIB_VERSION))
-		txbug = false;
+	sysid_parent = of_find_node_by_path("/ambapp0");
+	if (sysid_parent) {
+		err = of_property_read_u32(sysid_parent, "systemid", &sysid);
+		if (!err && ((sysid & GRLIB_VERSION_MASK) >=
+			     GRCAN_TXBUG_SAFE_GRLIB_VERSION))
+			txbug = false;
+		of_node_put(sysid_parent);
+	}
 
 	err = of_property_read_u32(np, "freq", &ambafreq);
 	if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/ifi_canfd/ifi_canfd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/ifi_canfd/ifi_canfd.c
@@ -393,36 +393,55 @@
 		return 0;
 
 	priv->can.can_stats.bus_error++;
-	stats->rx_errors++;
 
 	/* Propagate the error condition to the CAN stack. */
 	skb = alloc_can_err_skb(ndev, &cf);
-	if (unlikely(!skb))
-		return 0;
 
 	/* Read the error counter register and check for new errors. */
-	cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+	if (likely(skb))
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
 
-	if (errctr & IFI_CANFD_ERROR_CTR_OVERLOAD_FIRST)
-		cf->data[2] |= CAN_ERR_PROT_OVERLOAD;
+	if (errctr & IFI_CANFD_ERROR_CTR_OVERLOAD_FIRST) {
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_OVERLOAD;
+	}
 
-	if (errctr & IFI_CANFD_ERROR_CTR_ACK_ERROR_FIRST)
-		cf->data[3] = CAN_ERR_PROT_LOC_ACK;
+	if (errctr & IFI_CANFD_ERROR_CTR_ACK_ERROR_FIRST) {
+		stats->tx_errors++;
+		if (likely(skb))
+			cf->data[3] = CAN_ERR_PROT_LOC_ACK;
+	}
 
-	if (errctr & IFI_CANFD_ERROR_CTR_BIT0_ERROR_FIRST)
-		cf->data[2] |= CAN_ERR_PROT_BIT0;
+	if (errctr & IFI_CANFD_ERROR_CTR_BIT0_ERROR_FIRST) {
+		stats->tx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_BIT0;
+	}
 
-	if (errctr & IFI_CANFD_ERROR_CTR_BIT1_ERROR_FIRST)
-		cf->data[2] |= CAN_ERR_PROT_BIT1;
+	if (errctr & IFI_CANFD_ERROR_CTR_BIT1_ERROR_FIRST) {
+		stats->tx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_BIT1;
+	}
 
-	if (errctr & IFI_CANFD_ERROR_CTR_STUFF_ERROR_FIRST)
-		cf->data[2] |= CAN_ERR_PROT_STUFF;
+	if (errctr & IFI_CANFD_ERROR_CTR_STUFF_ERROR_FIRST) {
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_STUFF;
+	}
 
-	if (errctr & IFI_CANFD_ERROR_CTR_CRC_ERROR_FIRST)
-		cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ;
+	if (errctr & IFI_CANFD_ERROR_CTR_CRC_ERROR_FIRST) {
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ;
+	}
 
-	if (errctr & IFI_CANFD_ERROR_CTR_FORM_ERROR_FIRST)
-		cf->data[2] |= CAN_ERR_PROT_FORM;
+	if (errctr & IFI_CANFD_ERROR_CTR_FORM_ERROR_FIRST) {
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_FORM;
+	}
 
 	/* Reset the error counter, ack the IRQ and re-enable the counter. */
 	writel(IFI_CANFD_ERROR_CTR_ER_RESET, priv->base + IFI_CANFD_ERROR_CTR);
@@ -430,8 +449,9 @@
 	       priv->base + IFI_CANFD_INTERRUPT);
 	writel(IFI_CANFD_ERROR_CTR_ER_ENABLE, priv->base + IFI_CANFD_ERROR_CTR);
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
+	if (unlikely(!skb))
+		return 0;
+
 	netif_receive_skb(skb);
 
 	return 1;
@@ -456,7 +476,6 @@
 					 enum can_state new_state)
 {
 	struct ifi_canfd_priv *priv = netdev_priv(ndev);
-	struct net_device_stats *stats = &ndev->stats;
 	struct can_frame *cf;
 	struct sk_buff *skb;
 	struct can_berr_counter bec;
@@ -522,8 +541,6 @@
 		break;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_receive_skb(skb);
 
 	return 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/kvaser_pciefd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/kvaser_pciefd.c
@@ -70,10 +70,12 @@
 #define KVASER_PCIEFD_SYSID_BUILD_REG (KVASER_PCIEFD_SYSID_BASE + 0x14)
 /* Shared receive buffer registers */
 #define KVASER_PCIEFD_SRB_BASE 0x1f200
+#define KVASER_PCIEFD_SRB_FIFO_LAST_REG (KVASER_PCIEFD_SRB_BASE + 0x1f4)
 #define KVASER_PCIEFD_SRB_CMD_REG (KVASER_PCIEFD_SRB_BASE + 0x200)
 #define KVASER_PCIEFD_SRB_IEN_REG (KVASER_PCIEFD_SRB_BASE + 0x204)
 #define KVASER_PCIEFD_SRB_IRQ_REG (KVASER_PCIEFD_SRB_BASE + 0x20c)
 #define KVASER_PCIEFD_SRB_STAT_REG (KVASER_PCIEFD_SRB_BASE + 0x210)
+#define KVASER_PCIEFD_SRB_RX_NR_PACKETS_REG (KVASER_PCIEFD_SRB_BASE + 0x214)
 #define KVASER_PCIEFD_SRB_CTRL_REG (KVASER_PCIEFD_SRB_BASE + 0x218)
 /* EPCS flash controller registers */
 #define KVASER_PCIEFD_SPI_BASE 0x1fc00
@@ -110,6 +112,9 @@
 /* DMA support */
 #define KVASER_PCIEFD_SRB_STAT_DMA BIT(24)
 
+/* SRB current packet level */
+#define KVASER_PCIEFD_SRB_RX_NR_PACKETS_MASK 0xff
+
 /* DMA Enable */
 #define KVASER_PCIEFD_SRB_CTRL_DMA_ENABLE BIT(0)
 
@@ -248,6 +253,9 @@
 #define KVASER_PCIEFD_SPACK_EWLR BIT(23)
 #define KVASER_PCIEFD_SPACK_EPLR BIT(24)
 
+/* Kvaser KCAN_EPACK second word */
+#define KVASER_PCIEFD_EPACK_DIR_TX BIT(0)
+
 struct kvaser_pciefd;
 
 struct kvaser_pciefd_can {
@@ -525,7 +533,7 @@
 	      KVASER_PCIEFD_KCAN_IRQ_TOF | KVASER_PCIEFD_KCAN_IRQ_ABD |
 	      KVASER_PCIEFD_KCAN_IRQ_TAE | KVASER_PCIEFD_KCAN_IRQ_TAL |
 	      KVASER_PCIEFD_KCAN_IRQ_FDIC | KVASER_PCIEFD_KCAN_IRQ_BPP |
-	      KVASER_PCIEFD_KCAN_IRQ_TAR | KVASER_PCIEFD_KCAN_IRQ_TFD;
+	      KVASER_PCIEFD_KCAN_IRQ_TAR;
 
 	iowrite32(msk, can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 
@@ -553,6 +561,8 @@
 
 	if (can->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)
 		mode |= KVASER_PCIEFD_KCAN_MODE_LOM;
+	else
+		mode &= ~KVASER_PCIEFD_KCAN_MODE_LOM;
 
 	mode |= KVASER_PCIEFD_KCAN_MODE_EEN;
 	mode |= KVASER_PCIEFD_KCAN_MODE_EPEN;
@@ -571,7 +581,7 @@
 
 	spin_lock_irqsave(&can->lock, irq);
 	iowrite32(-1, can->reg_base + KVASER_PCIEFD_KCAN_IRQ_REG);
-	iowrite32(KVASER_PCIEFD_KCAN_IRQ_ABD | KVASER_PCIEFD_KCAN_IRQ_TFD,
+	iowrite32(KVASER_PCIEFD_KCAN_IRQ_ABD,
 		  can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 
 	status = ioread32(can->reg_base + KVASER_PCIEFD_KCAN_STAT_REG);
@@ -614,7 +624,7 @@
 	iowrite32(0, can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 	iowrite32(-1, can->reg_base + KVASER_PCIEFD_KCAN_IRQ_REG);
 
-	iowrite32(KVASER_PCIEFD_KCAN_IRQ_ABD | KVASER_PCIEFD_KCAN_IRQ_TFD,
+	iowrite32(KVASER_PCIEFD_KCAN_IRQ_ABD,
 		  can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 
 	mode = ioread32(can->reg_base + KVASER_PCIEFD_KCAN_MODE_REG);
@@ -718,6 +728,7 @@
 		iowrite32(0, can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 		del_timer(&can->bec_poll_timer);
 	}
+	can->can.state = CAN_STATE_STOPPED;
 	close_candev(netdev);
 
 	return ret;
@@ -1000,8 +1011,7 @@
 		SET_NETDEV_DEV(netdev, &pcie->pci->dev);
 
 		iowrite32(-1, can->reg_base + KVASER_PCIEFD_KCAN_IRQ_REG);
-		iowrite32(KVASER_PCIEFD_KCAN_IRQ_ABD |
-			  KVASER_PCIEFD_KCAN_IRQ_TFD,
+		iowrite32(KVASER_PCIEFD_KCAN_IRQ_ABD,
 			  can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 
 		pcie->can[i] = can;
@@ -1051,6 +1061,7 @@
 {
 	int i;
 	u32 srb_status;
+	u32 srb_packet_count;
 	dma_addr_t dma_addr[KVASER_PCIEFD_DMA_COUNT];
 
 	/* Disable the DMA */
@@ -1078,6 +1089,15 @@
 		  KVASER_PCIEFD_SRB_CMD_RDB1,
 		  pcie->reg_base + KVASER_PCIEFD_SRB_CMD_REG);
 
+	/* Empty Rx FIFO */
+	srb_packet_count = ioread32(pcie->reg_base + KVASER_PCIEFD_SRB_RX_NR_PACKETS_REG) &
+			   KVASER_PCIEFD_SRB_RX_NR_PACKETS_MASK;
+	while (srb_packet_count) {
+		/* Drop current packet in FIFO */
+		ioread32(pcie->reg_base + KVASER_PCIEFD_SRB_FIFO_LAST_REG);
+		srb_packet_count--;
+	}
+
 	srb_status = ioread32(pcie->reg_base + KVASER_PCIEFD_SRB_STAT_REG);
 	if (!(srb_status & KVASER_PCIEFD_SRB_STAT_DI)) {
 		dev_err(&pcie->pci->dev, "DMA not idle before enabling\n");
@@ -1285,7 +1305,10 @@
 
 	can->err_rep_cnt++;
 	can->can.can_stats.bus_error++;
-	stats->rx_errors++;
+	if (p->header[1] & KVASER_PCIEFD_EPACK_DIR_TX)
+		stats->tx_errors++;
+	else
+		stats->rx_errors++;
 
 	can->bec.txerr = bec.txerr;
 	can->bec.rxerr = bec.rxerr;
@@ -1304,9 +1327,6 @@
 	cf->data[6] = bec.txerr;
 	cf->data[7] = bec.rxerr;
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
-
 	netif_rx(skb);
 	return 0;
 }
@@ -1417,9 +1437,6 @@
 		cmd = KVASER_PCIEFD_KCAN_CMD_AT;
 		cmd |= ++can->cmd_seq << KVASER_PCIEFD_KCAN_CMD_SEQ_SHIFT;
 		iowrite32(cmd, can->reg_base + KVASER_PCIEFD_KCAN_CMD_REG);
-
-		iowrite32(KVASER_PCIEFD_KCAN_IRQ_TFD,
-			  can->reg_base + KVASER_PCIEFD_KCAN_IEN_REG);
 	} else if (p->header[0] & KVASER_PCIEFD_SPACK_IDET &&
 		   p->header[0] & KVASER_PCIEFD_SPACK_IRM &&
 		   cmdseq == (p->header[1] & KVASER_PCIEFD_PACKET_SEQ_MSK) &&
@@ -1504,8 +1521,6 @@
 
 	if (skb) {
 		cf->can_id |= CAN_ERR_BUSERROR;
-		stats->rx_bytes += cf->len;
-		stats->rx_packets++;
 		netif_rx(skb);
 	} else {
 		stats->rx_dropped++;
@@ -1708,15 +1723,6 @@
 	if (irq & KVASER_PCIEFD_KCAN_IRQ_TOF)
 		netdev_err(can->can.dev, "Tx FIFO overflow\n");
 
-	if (irq & KVASER_PCIEFD_KCAN_IRQ_TFD) {
-		u8 count = ioread32(can->reg_base +
-				    KVASER_PCIEFD_KCAN_TX_NPACKETS_REG) & 0xff;
-
-		if (count == 0)
-			iowrite32(KVASER_PCIEFD_KCAN_CTRL_EFLUSH,
-				  can->reg_base + KVASER_PCIEFD_KCAN_CTRL_REG);
-	}
-
 	if (irq & KVASER_PCIEFD_KCAN_IRQ_BPP)
 		netdev_err(can->can.dev,
 			   "Fail to change bittiming, when not in reset mode\n");
@@ -1818,6 +1824,11 @@
 	if (err)
 		goto err_teardown_can_ctrls;
 
+	err = request_irq(pcie->pci->irq, kvaser_pciefd_irq_handler,
+			  IRQF_SHARED, KVASER_PCIEFD_DRV_NAME, pcie);
+	if (err)
+		goto err_teardown_can_ctrls;
+
 	iowrite32(KVASER_PCIEFD_SRB_IRQ_DPD0 | KVASER_PCIEFD_SRB_IRQ_DPD1,
 		  pcie->reg_base + KVASER_PCIEFD_SRB_IRQ_REG);
 
@@ -1838,11 +1849,6 @@
 	iowrite32(KVASER_PCIEFD_SRB_CMD_RDB1,
 		  pcie->reg_base + KVASER_PCIEFD_SRB_CMD_REG);
 
-	err = request_irq(pcie->pci->irq, kvaser_pciefd_irq_handler,
-			  IRQF_SHARED, KVASER_PCIEFD_DRV_NAME, pcie);
-	if (err)
-		goto err_teardown_can_ctrls;
-
 	err = kvaser_pciefd_reg_candev(pcie);
 	if (err)
 		goto err_free_irq;
@@ -1850,6 +1856,8 @@
 	return 0;
 
 err_free_irq:
+	/* Disable PCI interrupts */
+	iowrite32(0, pcie->reg_base + KVASER_PCIEFD_IEN_REG);
 	free_irq(pcie->pci->irq, pcie);
 
 err_teardown_can_ctrls:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/m_can/m_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/m_can/m_can.c
@@ -204,16 +204,16 @@
 
 /* Interrupts for version 3.0.x */
 #define IR_ERR_LEC_30X	(IR_STE	| IR_FOE | IR_ACKE | IR_BE | IR_CRCE)
-#define IR_ERR_BUS_30X	(IR_ERR_LEC_30X | IR_WDI | IR_ELO | IR_BEU | \
-			 IR_BEC | IR_TOO | IR_MRAF | IR_TSW | IR_TEFL | \
-			 IR_RF1L | IR_RF0L)
+#define IR_ERR_BUS_30X	(IR_ERR_LEC_30X | IR_WDI | IR_BEU | IR_BEC | \
+			 IR_TOO | IR_MRAF | IR_TSW | IR_TEFL | IR_RF1L | \
+			 IR_RF0L)
 #define IR_ERR_ALL_30X	(IR_ERR_STATE | IR_ERR_BUS_30X)
 
 /* Interrupts for version >= 3.1.x */
 #define IR_ERR_LEC_31X	(IR_PED | IR_PEA)
-#define IR_ERR_BUS_31X      (IR_ERR_LEC_31X | IR_WDI | IR_ELO | IR_BEU | \
-			 IR_BEC | IR_TOO | IR_MRAF | IR_TSW | IR_TEFL | \
-			 IR_RF1L | IR_RF0L)
+#define IR_ERR_BUS_31X      (IR_ERR_LEC_31X | IR_WDI | IR_BEU | IR_BEC | \
+			 IR_TOO | IR_MRAF | IR_TSW | IR_TEFL | IR_RF1L | \
+			 IR_RF0L)
 #define IR_ERR_ALL_31X	(IR_ERR_STATE | IR_ERR_BUS_31X)
 
 /* Interrupt Line Select (ILS) */
@@ -336,6 +336,9 @@
 	u32 addr_offset = cdev->mcfg[MRAM_RXF0].off + fgi * RXF0_ELEMENT_SIZE +
 		offset;
 
+	if (val_count == 0)
+		return 0;
+
 	return cdev->ops->read_fifo(cdev, addr_offset, val, val_count);
 }
 
@@ -346,6 +349,9 @@
 	u32 addr_offset = cdev->mcfg[MRAM_TXB].off + fpi * TXB_ELEMENT_SIZE +
 		offset;
 
+	if (val_count == 0)
+		return 0;
+
 	return cdev->ops->write_fifo(cdev, addr_offset, val, val_count);
 }
 
@@ -517,7 +523,7 @@
 		err = m_can_fifo_read(cdev, fgi, M_CAN_FIFO_DATA,
 				      cf->data, DIV_ROUND_UP(cf->len, 4));
 		if (err)
-			goto out_fail;
+			goto out_free_skb;
 	}
 
 	/* acknowledge rx fifo 0 */
@@ -526,12 +532,14 @@
 	stats->rx_packets++;
 	stats->rx_bytes += cf->len;
 
-	timestamp = FIELD_GET(RX_BUF_RXTS_MASK, fifo_header.dlc);
+	timestamp = FIELD_GET(RX_BUF_RXTS_MASK, fifo_header.dlc) << 16;
 
 	m_can_receive_skb(cdev, skb, timestamp);
 
 	return 0;
 
+out_free_skb:
+	kfree_skb(skb);
 out_fail:
 	netdev_err(dev, "FIFO read returned %d\n", err);
 	return err;
@@ -604,49 +612,59 @@
 	u32 timestamp = 0;
 
 	cdev->can.can_stats.bus_error++;
-	stats->rx_errors++;
 
 	/* propagate the error condition to the CAN stack */
 	skb = alloc_can_err_skb(dev, &cf);
-	if (unlikely(!skb))
-		return 0;
 
 	/* check for 'last error code' which tells us the
 	 * type of the last error to occur on the CAN bus
 	 */
-	cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+	if (likely(skb))
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
 
 	switch (lec_type) {
 	case LEC_STUFF_ERROR:
 		netdev_dbg(dev, "stuff error\n");
-		cf->data[2] |= CAN_ERR_PROT_STUFF;
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_STUFF;
 		break;
 	case LEC_FORM_ERROR:
 		netdev_dbg(dev, "form error\n");
-		cf->data[2] |= CAN_ERR_PROT_FORM;
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_FORM;
 		break;
 	case LEC_ACK_ERROR:
 		netdev_dbg(dev, "ack error\n");
-		cf->data[3] = CAN_ERR_PROT_LOC_ACK;
+		stats->tx_errors++;
+		if (likely(skb))
+			cf->data[3] = CAN_ERR_PROT_LOC_ACK;
 		break;
 	case LEC_BIT1_ERROR:
 		netdev_dbg(dev, "bit1 error\n");
-		cf->data[2] |= CAN_ERR_PROT_BIT1;
+		stats->tx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_BIT1;
 		break;
 	case LEC_BIT0_ERROR:
 		netdev_dbg(dev, "bit0 error\n");
-		cf->data[2] |= CAN_ERR_PROT_BIT0;
+		stats->tx_errors++;
+		if (likely(skb))
+			cf->data[2] |= CAN_ERR_PROT_BIT0;
 		break;
 	case LEC_CRC_ERROR:
 		netdev_dbg(dev, "CRC error\n");
-		cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ;
+		stats->rx_errors++;
+		if (likely(skb))
+			cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ;
 		break;
 	default:
 		break;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
+	if (unlikely(!skb))
+		return 0;
 
 	if (cdev->is_peripheral)
 		timestamp = m_can_get_timestamp(cdev);
@@ -704,7 +722,6 @@
 				     enum can_state new_state)
 {
 	struct m_can_classdev *cdev = netdev_priv(dev);
-	struct net_device_stats *stats = &dev->stats;
 	struct can_frame *cf;
 	struct sk_buff *skb;
 	struct can_berr_counter bec;
@@ -769,9 +786,6 @@
 		break;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
-
 	if (cdev->is_peripheral)
 		timestamp = m_can_get_timestamp(cdev);
 
@@ -810,8 +824,6 @@
 {
 	if (irqstatus & IR_WDI)
 		netdev_err(dev, "Message RAM Watchdog event due to missing READY\n");
-	if (irqstatus & IR_ELO)
-		netdev_err(dev, "Error Logging Overflow\n");
 	if (irqstatus & IR_BEU)
 		netdev_err(dev, "Bit Error Uncorrected\n");
 	if (irqstatus & IR_BEC)
@@ -1037,7 +1049,7 @@
 		}
 
 		msg_mark = FIELD_GET(TX_EVENT_MM_MASK, txe);
-		timestamp = FIELD_GET(TX_EVENT_TXTS_MASK, txe);
+		timestamp = FIELD_GET(TX_EVENT_TXTS_MASK, txe) << 16;
 
 		/* ack txe element */
 		m_can_write(cdev, M_CAN_TXEFA, FIELD_PREP(TXEFA_EFAI_MASK,
@@ -1242,10 +1254,17 @@
  * - setup bittiming
  * - configure timestamp generation
  */
-static void m_can_chip_config(struct net_device *dev)
+static int m_can_chip_config(struct net_device *dev)
 {
 	struct m_can_classdev *cdev = netdev_priv(dev);
 	u32 cccr, test;
+	int err;
+
+	err = m_can_init_ram(cdev);
+	if (err) {
+		dev_err(cdev->dev, "Message RAM configuration failed\n");
+		return err;
+	}
 
 	m_can_config_endisable(cdev, true);
 
@@ -1361,24 +1380,33 @@
 	/* enable internal timestamp generation, with a prescalar of 16. The
 	 * prescalar is applied to the nominal bit timing
 	 */
-	m_can_write(cdev, M_CAN_TSCC, FIELD_PREP(TSCC_TCP_MASK, 0xf));
+	m_can_write(cdev, M_CAN_TSCC,
+		    FIELD_PREP(TSCC_TCP_MASK, 0xf) |
+		    FIELD_PREP(TSCC_TSS_MASK, TSCC_TSS_INTERNAL));
 
 	m_can_config_endisable(cdev, false);
 
 	if (cdev->ops->init)
 		cdev->ops->init(cdev);
+
+	return 0;
 }
 
-static void m_can_start(struct net_device *dev)
+static int m_can_start(struct net_device *dev)
 {
 	struct m_can_classdev *cdev = netdev_priv(dev);
+	int ret;
 
 	/* basic m_can configuration */
-	m_can_chip_config(dev);
+	ret = m_can_chip_config(dev);
+	if (ret)
+		return ret;
 
 	cdev->can.state = CAN_STATE_ERROR_ACTIVE;
 
 	m_can_enable_all_interrupts(cdev);
+
+	return 0;
 }
 
 static int m_can_set_mode(struct net_device *dev, enum can_mode mode)
@@ -1494,20 +1522,32 @@
 	case 30:
 		/* CAN_CTRLMODE_FD_NON_ISO is fixed with M_CAN IP v3.0.x */
 		can_set_static_ctrlmode(dev, CAN_CTRLMODE_FD_NON_ISO);
-		cdev->can.bittiming_const = &m_can_bittiming_const_30X;
-		cdev->can.data_bittiming_const = &m_can_data_bittiming_const_30X;
+		cdev->can.bittiming_const = cdev->bit_timing ?
+			cdev->bit_timing : &m_can_bittiming_const_30X;
+
+		cdev->can.data_bittiming_const = cdev->data_timing ?
+			cdev->data_timing :
+			&m_can_data_bittiming_const_30X;
 		break;
 	case 31:
 		/* CAN_CTRLMODE_FD_NON_ISO is fixed with M_CAN IP v3.1.x */
 		can_set_static_ctrlmode(dev, CAN_CTRLMODE_FD_NON_ISO);
-		cdev->can.bittiming_const = &m_can_bittiming_const_31X;
-		cdev->can.data_bittiming_const = &m_can_data_bittiming_const_31X;
+		cdev->can.bittiming_const = cdev->bit_timing ?
+			cdev->bit_timing : &m_can_bittiming_const_31X;
+
+		cdev->can.data_bittiming_const = cdev->data_timing ?
+			cdev->data_timing :
+			&m_can_data_bittiming_const_31X;
 		break;
 	case 32:
 	case 33:
 		/* Support both MCAN version v3.2.x and v3.3.0 */
-		cdev->can.bittiming_const = &m_can_bittiming_const_31X;
-		cdev->can.data_bittiming_const = &m_can_data_bittiming_const_31X;
+		cdev->can.bittiming_const = cdev->bit_timing ?
+			cdev->bit_timing : &m_can_bittiming_const_31X;
+
+		cdev->can.data_bittiming_const = cdev->data_timing ?
+			cdev->data_timing :
+			&m_can_data_bittiming_const_31X;
 
 		cdev->can.ctrlmode_supported |=
 			(m_can_niso_supported(cdev) ?
@@ -1549,7 +1589,6 @@
 		napi_disable(&cdev->napi);
 
 	m_can_stop(dev);
-	m_can_clk_stop(cdev);
 	free_irq(dev->irq, dev);
 
 	if (cdev->is_peripheral) {
@@ -1564,6 +1603,7 @@
 	close_candev(dev);
 	can_led_event(dev, CAN_LED_EVENT_STOP);
 
+	m_can_clk_stop(cdev);
 	phy_power_off(cdev->transceiver);
 
 	return 0;
@@ -1622,8 +1662,6 @@
 		if (err)
 			goto out_fail;
 
-		can_put_echo_skb(skb, dev, 0, 0);
-
 		if (cdev->can.ctrlmode & CAN_CTRLMODE_FD) {
 			cccr = m_can_read(cdev, M_CAN_CCCR);
 			cccr &= ~CCCR_CMR_MASK;
@@ -1640,6 +1678,9 @@
 			m_can_write(cdev, M_CAN_CCCR, cccr);
 		}
 		m_can_write(cdev, M_CAN_TXBTIE, 0x1);
+
+		can_put_echo_skb(skb, dev, 0, 0);
+
 		m_can_write(cdev, M_CAN_TXBAR, 0x1);
 		/* End of xmit function for version 3.0.x */
 	} else {
@@ -1803,7 +1844,9 @@
 	}
 
 	/* start the m_can controller */
-	m_can_start(dev);
+	err = m_can_start(dev);
+	if (err)
+		goto exit_start_fail;
 
 	can_led_event(dev, CAN_LED_EVENT_OPEN);
 
@@ -1814,6 +1857,9 @@
 
 	return 0;
 
+exit_start_fail:
+	if (cdev->is_peripheral || dev->irq)
+		free_irq(dev->irq, dev);
 exit_irq_fail:
 	if (cdev->is_peripheral)
 		destroy_workqueue(cdev->tx_wq);
@@ -1910,7 +1956,7 @@
 	cdev->hclk = devm_clk_get(cdev->dev, "hclk");
 	cdev->cclk = devm_clk_get(cdev->dev, "cclk");
 
-	if (IS_ERR(cdev->cclk)) {
+	if (IS_ERR(cdev->hclk) || IS_ERR(cdev->cclk)) {
 		dev_err(cdev->dev, "no clock found\n");
 		ret = -ENODEV;
 	}
@@ -2061,9 +2107,13 @@
 		ret = m_can_clk_start(cdev);
 		if (ret)
 			return ret;
+		ret  = m_can_start(ndev);
+		if (ret) {
+			m_can_clk_stop(cdev);
+
+			return ret;
+		}
 
-		m_can_init_ram(cdev);
-		m_can_start(ndev);
 		netif_device_attach(ndev);
 		netif_start_queue(ndev);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/m_can/m_can.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/m_can/m_can.h
@@ -85,6 +85,9 @@
 	struct sk_buff *tx_skb;
 	struct phy *transceiver;
 
+	const struct can_bittiming_const *bit_timing;
+	const struct can_bittiming_const *data_timing;
+
 	struct m_can_ops *ops;
 
 	int version;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/m_can/m_can_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/m_can/m_can_pci.c
@@ -18,7 +18,7 @@
 
 #define M_CAN_PCI_MMIO_BAR		0
 
-#define M_CAN_CLOCK_FREQ_EHL		100000000
+#define M_CAN_CLOCK_FREQ_EHL		200000000
 #define CTL_CSR_INT_CTL_OFFSET		0x508
 
 struct m_can_pci_priv {
@@ -42,8 +42,13 @@
 static int iomap_read_fifo(struct m_can_classdev *cdev, int offset, void *val, size_t val_count)
 {
 	struct m_can_pci_priv *priv = cdev_to_priv(cdev);
+	void __iomem *src = priv->base + offset;
 
-	ioread32_rep(priv->base + offset, val, val_count);
+	while (val_count--) {
+		*(unsigned int *)val = ioread32(src);
+		val += 4;
+		src += 4;
+	}
 
 	return 0;
 }
@@ -61,8 +66,13 @@
 			    const void *val, size_t val_count)
 {
 	struct m_can_pci_priv *priv = cdev_to_priv(cdev);
+	void __iomem *dst = priv->base + offset;
 
-	iowrite32_rep(priv->base + offset, val, val_count);
+	while (val_count--) {
+		iowrite32(*(unsigned int *)val, dst);
+		val += 4;
+		dst += 4;
+	}
 
 	return 0;
 }
@@ -110,7 +120,7 @@
 
 	ret = pci_alloc_irq_vectors(pci, 1, 1, PCI_IRQ_ALL_TYPES);
 	if (ret < 0)
-		return ret;
+		goto err_free_dev;
 
 	mcan_class->dev = &pci->dev;
 	mcan_class->net->irq = pci_irq_vector(pci, 0);
@@ -122,7 +132,7 @@
 
 	ret = m_can_class_register(mcan_class);
 	if (ret)
-		goto err;
+		goto err_free_irq;
 
 	/* Enable interrupt control at CAN wrapper IP */
 	writel(0x1, base + CTL_CSR_INT_CTL_OFFSET);
@@ -134,8 +144,10 @@
 
 	return 0;
 
-err:
+err_free_irq:
 	pci_free_irq_vectors(pci);
+err_free_dev:
+	m_can_class_free_dev(mcan_class->net);
 	return ret;
 }
 
@@ -151,6 +163,7 @@
 	writel(0x0, priv->base + CTL_CSR_INT_CTL_OFFSET);
 
 	m_can_class_unregister(mcan_class);
+	m_can_class_free_dev(mcan_class->net);
 	pci_free_irq_vectors(pci);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/m_can/m_can_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/m_can/m_can_platform.c
@@ -140,10 +140,6 @@
 
 	platform_set_drvdata(pdev, mcan_class);
 
-	ret = m_can_init_ram(mcan_class);
-	if (ret)
-		goto probe_fail;
-
 	pm_runtime_enable(mcan_class->dev);
 	ret = m_can_class_register(mcan_class);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/m_can/tcan4x5x-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/m_can/tcan4x5x-core.c
@@ -10,7 +10,7 @@
 #define TCAN4X5X_DEV_ID1 0x04
 #define TCAN4X5X_REV 0x08
 #define TCAN4X5X_STATUS 0x0C
-#define TCAN4X5X_ERROR_STATUS 0x10
+#define TCAN4X5X_ERROR_STATUS_MASK 0x10
 #define TCAN4X5X_CONTROL 0x14
 
 #define TCAN4X5X_CONFIG 0x800
@@ -204,17 +204,7 @@
 	if (ret)
 		return ret;
 
-	ret = tcan4x5x_write_tcan_reg(cdev, TCAN4X5X_MCAN_INT_REG,
-				      TCAN4X5X_ENABLE_MCAN_INT);
-	if (ret)
-		return ret;
-
-	ret = tcan4x5x_write_tcan_reg(cdev, TCAN4X5X_INT_FLAGS,
-				      TCAN4X5X_CLEAR_ALL_INT);
-	if (ret)
-		return ret;
-
-	return tcan4x5x_write_tcan_reg(cdev, TCAN4X5X_ERROR_STATUS,
+	return tcan4x5x_write_tcan_reg(cdev, TCAN4X5X_INT_FLAGS,
 				       TCAN4X5X_CLEAR_ALL_INT);
 }
 
@@ -234,8 +224,8 @@
 	if (ret)
 		return ret;
 
-	/* Zero out the MCAN buffers */
-	ret = m_can_init_ram(cdev);
+	ret = tcan4x5x_write_tcan_reg(cdev, TCAN4X5X_ERROR_STATUS_MASK,
+				      TCAN4X5X_CLEAR_ALL_INT);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/m_can/tcan4x5x-regmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/m_can/tcan4x5x-regmap.c
@@ -12,7 +12,7 @@
 #define TCAN4X5X_SPI_INSTRUCTION_WRITE (0x61 << 24)
 #define TCAN4X5X_SPI_INSTRUCTION_READ (0x41 << 24)
 
-#define TCAN4X5X_MAX_REGISTER 0x8ffc
+#define TCAN4X5X_MAX_REGISTER 0x87fc
 
 static int tcan4x5x_regmap_gather_write(void *context,
 					const void *reg, size_t reg_len,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/mscan/mpc5xxx_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/mscan/mpc5xxx_can.c
@@ -322,14 +322,14 @@
 					       &mscan_clksrc);
 	if (!priv->can.clock.freq) {
 		dev_err(&ofdev->dev, "couldn't get MSCAN clock properties\n");
-		goto exit_free_mscan;
+		goto exit_put_clock;
 	}
 
 	err = register_mscandev(dev, mscan_clksrc);
 	if (err) {
 		dev_err(&ofdev->dev, "registering %s failed (err=%d)\n",
 			DRV_NAME, err);
-		goto exit_free_mscan;
+		goto exit_put_clock;
 	}
 
 	dev_info(&ofdev->dev, "MSCAN at 0x%p, irq %d, clock %d Hz\n",
@@ -337,7 +337,9 @@
 
 	return 0;
 
-exit_free_mscan:
+exit_put_clock:
+	if (data->put_clock)
+		data->put_clock(ofdev);
 	free_candev(dev);
 exit_dispose_irq:
 	irq_dispose_mapping(irq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/mscan/mscan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/mscan/mscan.c
@@ -401,13 +401,14 @@
 			continue;
 		}
 
-		if (canrflg & MSCAN_RXF)
+		if (canrflg & MSCAN_RXF) {
 			mscan_get_rx_frame(dev, frame);
-		else if (canrflg & MSCAN_ERR_IF)
+			stats->rx_packets++;
+			stats->rx_bytes += frame->len;
+		} else if (canrflg & MSCAN_ERR_IF) {
 			mscan_get_err_frame(dev, frame, canrflg);
+		}
 
-		stats->rx_packets++;
-		stats->rx_bytes += frame->len;
 		work_done++;
 		netif_receive_skb(skb);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/pch_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/pch_can.c
@@ -489,6 +489,7 @@
 	if (!skb)
 		return;
 
+	errc = ioread32(&priv->regs->errc);
 	if (status & PCH_BUS_OFF) {
 		pch_can_set_tx_all(priv, 0);
 		pch_can_set_rx_all(priv, 0);
@@ -496,9 +497,11 @@
 		cf->can_id |= CAN_ERR_BUSOFF;
 		priv->can.can_stats.bus_off++;
 		can_bus_off(ndev);
+	} else {
+		cf->data[6] = errc & PCH_TEC;
+		cf->data[7] = (errc & PCH_REC) >> 8;
 	}
 
-	errc = ioread32(&priv->regs->errc);
 	/* Warning interrupt. */
 	if (status & PCH_EWARN) {
 		state = CAN_STATE_ERROR_WARNING;
@@ -556,14 +559,8 @@
 		break;
 	}
 
-	cf->data[6] = errc & PCH_TEC;
-	cf->data[7] = (errc & PCH_REC) >> 8;
-
 	priv->can.state = state;
 	netif_receive_skb(skb);
-
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 }
 
 static irqreturn_t pch_can_interrupt(int irq, void *dev_id)
@@ -692,11 +689,11 @@
 			cf->data[i + 1] = data_reg >> 8;
 		}
 
-		netif_receive_skb(skb);
 		rcv_pkts++;
 		stats->rx_packets++;
 		quota--;
 		stats->rx_bytes += cf->len;
+		netif_receive_skb(skb);
 
 		pch_fifo_thresh(priv, obj_num);
 		obj_num++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/peak_canfd/peak_canfd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/peak_canfd/peak_canfd.c
@@ -409,8 +409,6 @@
 		return -ENOMEM;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	pucan_netif_rx(skb, msg->ts_low, msg->ts_high);
 
 	return 0;
@@ -438,8 +436,6 @@
 	cf->data[6] = priv->bec.txerr;
 	cf->data[7] = priv->bec.rxerr;
 
-	stats->rx_bytes += cf->len;
-	stats->rx_packets++;
 	netif_rx(skb);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/rcar/rcar_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/rcar/rcar_can.c
@@ -223,7 +223,6 @@
 static void rcar_can_error(struct net_device *ndev)
 {
 	struct rcar_can_priv *priv = netdev_priv(ndev);
-	struct net_device_stats *stats = &ndev->stats;
 	struct can_frame *cf;
 	struct sk_buff *skb;
 	u8 eifr, txerr = 0, rxerr = 0;
@@ -235,11 +234,8 @@
 	if (eifr & (RCAR_CAN_EIFR_EWIF | RCAR_CAN_EIFR_EPIF)) {
 		txerr = readb(&priv->regs->tecr);
 		rxerr = readb(&priv->regs->recr);
-		if (skb) {
+		if (skb)
 			cf->can_id |= CAN_ERR_CRTL;
-			cf->data[6] = txerr;
-			cf->data[7] = rxerr;
-		}
 	}
 	if (eifr & RCAR_CAN_EIFR_BEIF) {
 		int rx_errors = 0, tx_errors = 0;
@@ -339,6 +335,9 @@
 		can_bus_off(ndev);
 		if (skb)
 			cf->can_id |= CAN_ERR_BUSOFF;
+	} else if (skb) {
+		cf->data[6] = txerr;
+		cf->data[7] = rxerr;
 	}
 	if (eifr & RCAR_CAN_EIFR_ORIF) {
 		netdev_dbg(priv->ndev, "Receive overrun error interrupt\n");
@@ -362,11 +361,8 @@
 		}
 	}
 
-	if (skb) {
-		stats->rx_packets++;
-		stats->rx_bytes += cf->len;
+	if (skb)
 		netif_rx(skb);
-	}
 }
 
 static void rcar_can_tx_done(struct net_device *ndev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/rcar/rcar_canfd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/rcar/rcar_canfd.c
@@ -1033,8 +1033,6 @@
 	/* Clear channel error interrupts that are handled */
 	rcar_canfd_write(priv->base, RCANFD_CERFL(ch),
 			 RCANFD_CERFL_ERR(~cerfl));
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 }
 
@@ -1106,11 +1104,13 @@
 {
 	struct rcar_canfd_channel *priv = gpriv->ch[ch];
 	u32 ridx = ch + RCANFD_RFFIFO_IDX;
-	u32 sts;
+	u32 sts, cc;
 
 	/* Handle Rx interrupts */
 	sts = rcar_canfd_read(priv->base, RCANFD_RFSTS(ridx));
-	if (likely(sts & RCANFD_RFSTS_RFIF)) {
+	cc = rcar_canfd_read(priv->base, RCANFD_RFCC(ridx));
+	if (likely(sts & RCANFD_RFSTS_RFIF &&
+		   cc & RCANFD_RFCC_RFIE)) {
 		if (napi_schedule_prep(&priv->napi)) {
 			/* Disable Rx FIFO interrupts */
 			rcar_canfd_clear_bit(priv->base,
@@ -1174,8 +1174,6 @@
 		rx_state = txerr <= rxerr ? state : 0;
 
 		can_change_state(ndev, cf, tx_state, rx_state);
-		stats->rx_packets++;
-		stats->rx_bytes += cf->len;
 		netif_rx(skb);
 	}
 }
@@ -1195,11 +1193,9 @@
 
 static irqreturn_t rcar_canfd_channel_tx_interrupt(int irq, void *dev_id)
 {
-	struct rcar_canfd_global *gpriv = dev_id;
-	u32 ch;
+	struct rcar_canfd_channel *priv = dev_id;
 
-	for_each_set_bit(ch, &gpriv->channels_mask, RCANFD_NUM_CHANNELS)
-		rcar_canfd_handle_channel_tx(gpriv, ch);
+	rcar_canfd_handle_channel_tx(priv->gpriv, priv->channel);
 
 	return IRQ_HANDLED;
 }
@@ -1227,11 +1223,9 @@
 
 static irqreturn_t rcar_canfd_channel_err_interrupt(int irq, void *dev_id)
 {
-	struct rcar_canfd_global *gpriv = dev_id;
-	u32 ch;
+	struct rcar_canfd_channel *priv = dev_id;
 
-	for_each_set_bit(ch, &gpriv->channels_mask, RCANFD_NUM_CHANNELS)
-		rcar_canfd_handle_channel_err(gpriv, ch);
+	rcar_canfd_handle_channel_err(priv->gpriv, priv->channel);
 
 	return IRQ_HANDLED;
 }
@@ -1640,8 +1634,7 @@
 	ndev = alloc_candev(sizeof(*priv), RCANFD_FIFO_DEPTH);
 	if (!ndev) {
 		dev_err(&pdev->dev, "alloc_candev() failed\n");
-		err = -ENOMEM;
-		goto fail;
+		return -ENOMEM;
 	}
 	priv = netdev_priv(ndev);
 
@@ -1650,6 +1643,7 @@
 	priv->ndev = ndev;
 	priv->base = gpriv->base;
 	priv->channel = ch;
+	priv->gpriv = gpriv;
 	priv->can.clock.freq = fcan_freq;
 	dev_info(&pdev->dev, "can_clk rate is %u\n", priv->can.clock.freq);
 
@@ -1678,7 +1672,7 @@
 		}
 		err = devm_request_irq(&pdev->dev, err_irq,
 				       rcar_canfd_channel_err_interrupt, 0,
-				       irq_name, gpriv);
+				       irq_name, priv);
 		if (err) {
 			dev_err(&pdev->dev, "devm_request_irq CH Err(%d) failed, error %d\n",
 				err_irq, err);
@@ -1692,7 +1686,7 @@
 		}
 		err = devm_request_irq(&pdev->dev, tx_irq,
 				       rcar_canfd_channel_tx_interrupt, 0,
-				       irq_name, gpriv);
+				       irq_name, priv);
 		if (err) {
 			dev_err(&pdev->dev, "devm_request_irq Tx (%d) failed, error %d\n",
 				tx_irq, err);
@@ -1716,27 +1710,26 @@
 
 	priv->can.do_set_mode = rcar_canfd_do_set_mode;
 	priv->can.do_get_berr_counter = rcar_canfd_get_berr_counter;
-	priv->gpriv = gpriv;
 	SET_NETDEV_DEV(ndev, &pdev->dev);
 
 	netif_napi_add(ndev, &priv->napi, rcar_canfd_rx_poll,
 		       RCANFD_NAPI_WEIGHT);
+	spin_lock_init(&priv->tx_lock);
+	devm_can_led_init(ndev);
+	gpriv->ch[priv->channel] = priv;
 	err = register_candev(ndev);
 	if (err) {
 		dev_err(&pdev->dev,
 			"register_candev() failed, error %d\n", err);
 		goto fail_candev;
 	}
-	spin_lock_init(&priv->tx_lock);
-	devm_can_led_init(ndev);
-	gpriv->ch[priv->channel] = priv;
 	dev_info(&pdev->dev, "device registered (channel %u)\n", priv->channel);
 	return 0;
 
 fail_candev:
 	netif_napi_del(&priv->napi);
-	free_candev(ndev);
 fail:
+	free_candev(ndev);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/sja1000/ems_pcmcia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/sja1000/ems_pcmcia.c
@@ -234,7 +234,12 @@
 			free_sja1000dev(dev);
 	}
 
-	err = request_irq(dev->irq, &ems_pcmcia_interrupt, IRQF_SHARED,
+	if (!card->channels) {
+		err = -ENODEV;
+		goto failure_cleanup;
+	}
+
+	err = request_irq(pdev->irq, &ems_pcmcia_interrupt, IRQF_SHARED,
 			  DRV_NAME, card);
 	if (!err)
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/sja1000/sja1000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/sja1000/sja1000.c
@@ -404,9 +404,6 @@
 	txerr = priv->read_reg(priv, SJA1000_TXERR);
 	rxerr = priv->read_reg(priv, SJA1000_RXERR);
 
-	cf->data[6] = txerr;
-	cf->data[7] = rxerr;
-
 	if (isrc & IRQ_DOI) {
 		/* data overrun interrupt */
 		netdev_dbg(dev, "data overrun interrupt\n");
@@ -428,6 +425,10 @@
 		else
 			state = CAN_STATE_ERROR_ACTIVE;
 	}
+	if (state != CAN_STATE_BUS_OFF) {
+		cf->data[6] = txerr;
+		cf->data[7] = rxerr;
+	}
 	if (isrc & IRQ_BEI) {
 		/* bus error interrupt */
 		priv->can.can_stats.bus_error++;
@@ -487,8 +488,6 @@
 			can_bus_off(dev);
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/sja1000/sja1000_isa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/sja1000/sja1000_isa.c
@@ -202,22 +202,24 @@
 	if (err) {
 		dev_err(&pdev->dev, "registering %s failed (err=%d)\n",
 			DRV_NAME, err);
-		goto exit_unmap;
+		goto exit_free;
 	}
 
 	dev_info(&pdev->dev, "%s device registered (reg_base=0x%p, irq=%d)\n",
 		 DRV_NAME, priv->reg_base, dev->irq);
 	return 0;
 
- exit_unmap:
+exit_free:
+	free_sja1000dev(dev);
+exit_unmap:
 	if (mem[idx])
 		iounmap(base);
- exit_release:
+exit_release:
 	if (mem[idx])
 		release_mem_region(mem[idx], iosize);
 	else
 		release_region(port[idx], iosize);
- exit:
+exit:
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/softing/softing_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/softing/softing_cs.c
@@ -293,7 +293,7 @@
 	return 0;
 
 platform_failed:
-	kfree(dev);
+	platform_device_put(pdev);
 mem_failed:
 pcmcia_bad:
 pcmcia_failed:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/softing/softing_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/softing/softing_fw.c
@@ -565,18 +565,19 @@
 		if (ret < 0)
 			goto failed;
 	}
-	/* enable_error_frame */
-	/*
+
+	/* enable_error_frame
+	 *
 	 * Error reporting is switched off at the moment since
 	 * the receiving of them is not yet 100% verified
 	 * This should be enabled sooner or later
-	 *
-	if (error_reporting) {
+	 */
+	if (0 && error_reporting) {
 		ret = softing_fct_cmd(card, 51, "enable_error_frame");
 		if (ret < 0)
 			goto failed;
 	}
-	*/
+
 	/* initialize interface */
 	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 2]);
 	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 4]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/spi/hi311x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/spi/hi311x.c
@@ -670,20 +670,22 @@
 
 			txerr = hi3110_read(spi, HI3110_READ_TEC);
 			rxerr = hi3110_read(spi, HI3110_READ_REC);
-			cf->data[6] = txerr;
-			cf->data[7] = rxerr;
 			tx_state = txerr >= rxerr ? new_state : 0;
 			rx_state = txerr <= rxerr ? new_state : 0;
 			can_change_state(net, cf, tx_state, rx_state);
-			netif_rx_ni(skb);
 
 			if (new_state == CAN_STATE_BUS_OFF) {
+				netif_rx_ni(skb);
 				can_bus_off(net);
 				if (priv->can.restart_ms == 0) {
 					priv->force_quit = 1;
 					hi3110_hw_sleep(spi);
 					break;
 				}
+			} else {
+				cf->data[6] = txerr;
+				cf->data[7] = rxerr;
+				netif_rx_ni(skb);
 			}
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/spi/mcp251x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/spi/mcp251x.c
@@ -755,7 +755,7 @@
 	int ret;
 
 	/* Force wakeup interrupt to wake device, but don't execute IST */
-	disable_irq(spi->irq);
+	disable_irq_nosync(spi->irq);
 	mcp251x_write_2regs(spi, CANINTE, CANINTE_WAKIE, CANINTF_WAKIF);
 
 	/* Wait for oscillator startup timer after wake up */
@@ -1074,9 +1074,6 @@
 
 		mcp251x_read_2regs(spi, CANINTF, &intf, &eflag);
 
-		/* mask out flags we don't care about */
-		intf &= CANINTF_RX | CANINTF_TX | CANINTF_ERR;
-
 		/* receive buffer 0 */
 		if (intf & CANINTF_RX0IF) {
 			mcp251x_hw_rx(spi, 0);
@@ -1086,6 +1083,18 @@
 			if (mcp251x_is_2510(spi))
 				mcp251x_write_bits(spi, CANINTF,
 						   CANINTF_RX0IF, 0x00);
+
+			/* check if buffer 1 is already known to be full, no need to re-read */
+			if (!(intf & CANINTF_RX1IF)) {
+				u8 intf1, eflag1;
+
+				/* intf needs to be read again to avoid a race condition */
+				mcp251x_read_2regs(spi, CANINTF, &intf1, &eflag1);
+
+				/* combine flags from both operations for error handling */
+				intf |= intf1;
+				eflag |= eflag1;
+			}
 		}
 
 		/* receive buffer 1 */
@@ -1096,6 +1105,9 @@
 				clear_intf |= CANINTF_RX1IF;
 		}
 
+		/* mask out flags we don't care about */
+		intf &= CANINTF_RX | CANINTF_TX | CANINTF_ERR;
+
 		/* any error or tx interrupt we need to clear? */
 		if (intf & (CANINTF_ERR | CANINTF_TX))
 			clear_intf |= intf & (CANINTF_ERR | CANINTF_TX);
@@ -1407,11 +1419,14 @@
 
 	ret = mcp251x_gpio_setup(priv);
 	if (ret)
-		goto error_probe;
+		goto out_unregister_candev;
 
 	netdev_info(net, "MCP%x successfully initialized.\n", priv->model);
 	return 0;
 
+out_unregister_candev:
+	unregister_candev(net);
+
 error_probe:
 	destroy_workqueue(priv->wq);
 	priv->wq = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
@@ -1092,7 +1092,7 @@
 
 	err = mcp251xfd_chip_rx_int_enable(priv);
 	if (err)
-		return err;
+		goto out_chip_stop;
 
 	err = mcp251xfd_chip_ecc_init(priv);
 	if (err)
@@ -1336,7 +1336,7 @@
 	     len > tx_ring->obj_num ||
 	     offset + len > tx_ring->obj_num)) {
 		netdev_err(priv->ndev,
-			   "Trying to read to many TEF objects (max=%d, offset=%d, len=%d).\n",
+			   "Trying to read too many TEF objects (max=%d, offset=%d, len=%d).\n",
 			   tx_ring->obj_num, offset, len);
 		return -ERANGE;
 	}
@@ -2290,8 +2290,10 @@
 			 * check will fail, too. So leave IRQ handler
 			 * directly.
 			 */
-			if (priv->can.state == CAN_STATE_BUS_OFF)
+			if (priv->can.state == CAN_STATE_BUS_OFF) {
+				can_rx_offload_threaded_irq_finish(&priv->offload);
 				return IRQ_HANDLED;
+			}
 		}
 
 		handled = IRQ_HANDLED;
@@ -2623,7 +2625,7 @@
 	if (!mcp251xfd_is_251X(priv) &&
 	    priv->devtype_data.model != devtype_data->model) {
 		netdev_info(ndev,
-			    "Detected %s, but firmware specifies a %s. Fixing up.",
+			    "Detected %s, but firmware specifies a %s. Fixing up.\n",
 			    __mcp251xfd_get_model_str(devtype_data->model),
 			    mcp251xfd_get_model_str(priv));
 	}
@@ -2660,7 +2662,7 @@
 		return 0;
 
 	netdev_info(priv->ndev,
-		    "RX_INT active after softreset, disabling RX_INT support.");
+		    "RX_INT active after softreset, disabling RX_INT support.\n");
 	devm_gpiod_put(&priv->spi->dev, priv->rx_int);
 	priv->rx_int = NULL;
 
@@ -2704,7 +2706,7 @@
  out_kfree_buf_rx:
 	kfree(buf_rx);
 
-	return 0;
+	return err;
 }
 
 #define MCP251XFD_QUIRK_ACTIVE(quirk) \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/spi/mcp251xfd/mcp251xfd-regmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/spi/mcp251xfd/mcp251xfd-regmap.c
@@ -325,19 +325,21 @@
 		 * register. It increments once per SYS clock tick,
 		 * which is 20 or 40 MHz.
 		 *
-		 * Observation shows that if the lowest byte (which is
-		 * transferred first on the SPI bus) of that register
-		 * is 0x00 or 0x80 the calculated CRC doesn't always
-		 * match the transferred one.
+		 * Observation on the mcp2518fd shows that if the
+		 * lowest byte (which is transferred first on the SPI
+		 * bus) of that register is 0x00 or 0x80 the
+		 * calculated CRC doesn't always match the transferred
+		 * one. On the mcp2517fd this problem is not limited
+		 * to the first byte being 0x00 or 0x80.
 		 *
 		 * If the highest bit in the lowest byte is flipped
 		 * the transferred CRC matches the calculated one. We
-		 * assume for now the CRC calculation in the chip
-		 * works on wrong data and the transferred data is
-		 * correct.
+		 * assume for now the CRC operates on the correct
+		 * data.
 		 */
 		if (reg == MCP251XFD_REG_TBC &&
-		    (buf_rx->data[0] == 0x0 || buf_rx->data[0] == 0x80)) {
+		    ((buf_rx->data[0] & 0xf8) == 0x0 ||
+		     (buf_rx->data[0] & 0xf8) == 0x80)) {
 			/* Flip highest bit in lowest byte of le32 */
 			buf_rx->data[0] ^= 0x80;
 
@@ -347,10 +349,8 @@
 								  val_len);
 			if (!err) {
 				/* If CRC is now correct, assume
-				 * transferred data was OK, flip bit
-				 * back to original value.
+				 * flipped data is OK.
 				 */
-				buf_rx->data[0] ^= 0x80;
 				goto out;
 			}
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/spi/mcp251xfd/mcp251xfd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/spi/mcp251xfd/mcp251xfd.h
@@ -433,7 +433,7 @@
 /* The tx_obj_raw version is used in spi async, i.e. without
  * regmap. We have to take care of endianness ourselves.
  */
-struct mcp251xfd_hw_tx_obj_raw {
+struct __packed mcp251xfd_hw_tx_obj_raw {
 	__le32 id;
 	__le32 flags;
 	u8 data[sizeof_field(struct canfd_frame, data)];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/sun4i_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/sun4i_can.c
@@ -525,11 +525,6 @@
 	rxerr = (errc >> 16) & 0xFF;
 	txerr = errc & 0xFF;
 
-	if (skb) {
-		cf->data[6] = txerr;
-		cf->data[7] = rxerr;
-	}
-
 	if (isrc & SUN4I_INT_DATA_OR) {
 		/* data overrun interrupt */
 		netdev_dbg(dev, "data overrun interrupt\n");
@@ -560,15 +555,17 @@
 		else
 			state = CAN_STATE_ERROR_ACTIVE;
 	}
+	if (skb && state != CAN_STATE_BUS_OFF) {
+		cf->data[6] = txerr;
+		cf->data[7] = rxerr;
+	}
 	if (isrc & SUN4I_INT_BUS_ERR) {
 		/* bus error interrupt */
 		netdev_dbg(dev, "bus error interrupt\n");
 		priv->can.can_stats.bus_error++;
-		stats->rx_errors++;
+		ecc = readl(priv->base + SUN4I_REG_STA_ADDR);
 
 		if (likely(skb)) {
-			ecc = readl(priv->base + SUN4I_REG_STA_ADDR);
-
 			cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
 
 			switch (ecc & SUN4I_STA_MASK_ERR) {
@@ -586,9 +583,15 @@
 					       >> 16;
 				break;
 			}
-			/* error occurred during transmission? */
-			if ((ecc & SUN4I_STA_ERR_DIR) == 0)
+		}
+
+		/* error occurred during transmission? */
+		if ((ecc & SUN4I_STA_ERR_DIR) == 0) {
+			if (likely(skb))
 				cf->data[2] |= CAN_ERR_PROT_TX;
+			stats->tx_errors++;
+		} else {
+			stats->rx_errors++;
 		}
 	}
 	if (isrc & SUN4I_INT_ERR_PASSIVE) {
@@ -614,21 +617,18 @@
 		tx_state = txerr >= rxerr ? state : 0;
 		rx_state = txerr <= rxerr ? state : 0;
 
-		if (likely(skb))
-			can_change_state(dev, cf, tx_state, rx_state);
-		else
-			priv->can.state = state;
+		/* The skb allocation might fail, but can_change_state()
+		 * handles cf == NULL.
+		 */
+		can_change_state(dev, cf, tx_state, rx_state);
 		if (state == CAN_STATE_BUS_OFF)
 			can_bus_off(dev);
 	}
 
-	if (likely(skb)) {
-		stats->rx_packets++;
-		stats->rx_bytes += cf->len;
+	if (likely(skb))
 		netif_rx(skb);
-	} else {
+	else
 		return -ENOMEM;
-	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/Kconfig
@@ -30,6 +30,18 @@
 	  To compile this driver as a module, choose M here: the module
 	  will be called etas_es58x.
 
+config CAN_F81604
+        tristate "Fintek F81604 USB to 2CAN interface"
+        help
+          This driver supports the Fintek F81604 USB to 2CAN interface.
+          The device can support CAN2.0A/B protocol and also support
+          2 output pins to control external terminator (optional).
+
+          To compile this driver as a module, choose M here: the module will
+          be called f81604.
+
+          (see also https://www.fintek.com.tw).
+
 config CAN_GS_USB
 	tristate "Geschwister Schneider UG interfaces"
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/Makefile
@@ -7,6 +7,7 @@
 obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o
 obj-$(CONFIG_CAN_ESD_USB2) += esd_usb2.o
 obj-$(CONFIG_CAN_ETAS_ES58X) += etas_es58x/
+obj-$(CONFIG_CAN_F81604) += f81604.o
 obj-$(CONFIG_CAN_GS_USB) += gs_usb.o
 obj-$(CONFIG_CAN_KVASER_USB) += kvaser_usb/
 obj-$(CONFIG_CAN_MCBA_USB) += mcba_usb.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/ems_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/ems_usb.c
@@ -194,7 +194,7 @@
 	__le32 ts_sec;	/* timestamp in seconds */
 	__le32 ts_nsec;	/* timestamp in nano seconds */
 
-	union {
+	union __packed {
 		u8 generic[64];
 		struct cpc_can_msg can_msg;
 		struct cpc_can_params can_params;
@@ -334,15 +334,14 @@
 	struct net_device_stats *stats = &dev->netdev->stats;
 
 	skb = alloc_can_err_skb(dev->netdev, &cf);
-	if (skb == NULL)
-		return;
 
 	if (msg->type == CPC_MSG_TYPE_CAN_STATE) {
 		u8 state = msg->msg.can_state;
 
 		if (state & SJA1000_SR_BS) {
 			dev->can.state = CAN_STATE_BUS_OFF;
-			cf->can_id |= CAN_ERR_BUSOFF;
+			if (skb)
+				cf->can_id |= CAN_ERR_BUSOFF;
 
 			dev->can.can_stats.bus_off++;
 			can_bus_off(dev->netdev);
@@ -360,46 +359,53 @@
 
 		/* bus error interrupt */
 		dev->can.can_stats.bus_error++;
-		stats->rx_errors++;
 
-		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+		if (skb) {
+			cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
 
-		switch (ecc & SJA1000_ECC_MASK) {
-		case SJA1000_ECC_BIT:
-			cf->data[2] |= CAN_ERR_PROT_BIT;
-			break;
-		case SJA1000_ECC_FORM:
-			cf->data[2] |= CAN_ERR_PROT_FORM;
-			break;
-		case SJA1000_ECC_STUFF:
-			cf->data[2] |= CAN_ERR_PROT_STUFF;
-			break;
-		default:
-			cf->data[3] = ecc & SJA1000_ECC_SEG;
-			break;
+			switch (ecc & SJA1000_ECC_MASK) {
+			case SJA1000_ECC_BIT:
+				cf->data[2] |= CAN_ERR_PROT_BIT;
+				break;
+			case SJA1000_ECC_FORM:
+				cf->data[2] |= CAN_ERR_PROT_FORM;
+				break;
+			case SJA1000_ECC_STUFF:
+				cf->data[2] |= CAN_ERR_PROT_STUFF;
+				break;
+			default:
+				cf->data[3] = ecc & SJA1000_ECC_SEG;
+				break;
+			}
 		}
 
 		/* Error occurred during transmission? */
-		if ((ecc & SJA1000_ECC_DIR) == 0)
-			cf->data[2] |= CAN_ERR_PROT_TX;
+		if ((ecc & SJA1000_ECC_DIR) == 0) {
+			stats->tx_errors++;
+			if (skb)
+				cf->data[2] |= CAN_ERR_PROT_TX;
+		} else {
+			stats->rx_errors++;
+		}
 
-		if (dev->can.state == CAN_STATE_ERROR_WARNING ||
-		    dev->can.state == CAN_STATE_ERROR_PASSIVE) {
+		if (skb && (dev->can.state == CAN_STATE_ERROR_WARNING ||
+			    dev->can.state == CAN_STATE_ERROR_PASSIVE)) {
 			cf->can_id |= CAN_ERR_CRTL;
 			cf->data[1] = (txerr > rxerr) ?
 			    CAN_ERR_CRTL_TX_PASSIVE : CAN_ERR_CRTL_RX_PASSIVE;
 		}
 	} else if (msg->type == CPC_MSG_TYPE_OVERRUN) {
-		cf->can_id |= CAN_ERR_CRTL;
-		cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+		if (skb) {
+			cf->can_id |= CAN_ERR_CRTL;
+			cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+		}
 
 		stats->rx_over_errors++;
 		stats->rx_errors++;
 	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
-	netif_rx(skb);
+	if (skb)
+		netif_rx(skb);
 }
 
 /*
@@ -823,7 +829,6 @@
 
 		usb_unanchor_urb(urb);
 		usb_free_coherent(dev->udev, size, buf, urb->transfer_dma);
-		dev_kfree_skb(skb);
 
 		atomic_dec(&dev->active_tx_urbs);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/esd_usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/esd_usb2.c
@@ -227,6 +227,10 @@
 		u8 rxerr = msg->msg.rx.data[2];
 		u8 txerr = msg->msg.rx.data[3];
 
+		netdev_dbg(priv->netdev,
+			   "CAN_ERR_EV_EXT: dlc=%#02x state=%02x ecc=%02x rec=%02x tec=%02x\n",
+			   msg->msg.rx.dlc, state, ecc, rxerr, txerr);
+
 		skb = alloc_can_err_skb(priv->netdev, &cf);
 		if (skb == NULL) {
 			stats->rx_dropped++;
@@ -253,6 +257,8 @@
 				break;
 			default:
 				priv->can.state = CAN_STATE_ERROR_ACTIVE;
+				txerr = 0;
+				rxerr = 0;
 				break;
 			}
 		} else {
@@ -272,7 +278,6 @@
 				cf->data[2] |= CAN_ERR_PROT_STUFF;
 				break;
 			default:
-				cf->data[3] = ecc & SJA1000_ECC_SEG;
 				break;
 			}
 
@@ -280,6 +285,9 @@
 			if (!(ecc & SJA1000_ECC_DIR))
 				cf->data[2] |= CAN_ERR_PROT_TX;
 
+			/* Bit stream position in CAN frame as the error was detected */
+			cf->data[3] = ecc & SJA1000_ECC_SEG;
+
 			if (priv->can.state == CAN_STATE_ERROR_WARNING ||
 			    priv->can.state == CAN_STATE_ERROR_PASSIVE) {
 				cf->data[1] = (txerr > rxerr) ?
@@ -293,8 +301,6 @@
 		priv->bec.txerr = txerr;
 		priv->bec.rxerr = rxerr;
 
-		stats->rx_packets++;
-		stats->rx_bytes += cf->len;
 		netif_rx(skb);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/etas_es58x/es58x_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/etas_es58x/es58x_core.c
@@ -664,7 +664,7 @@
 	struct can_device_stats *can_stats = &can->can_stats;
 	struct can_frame *cf = NULL;
 	struct sk_buff *skb;
-	int ret;
+	int ret = 0;
 
 	if (!netif_running(netdev)) {
 		if (net_ratelimit())
@@ -823,8 +823,6 @@
 			can->state = CAN_STATE_BUS_OFF;
 			can_bus_off(netdev);
 			ret = can->do_set_mode(netdev, CAN_MODE_STOP);
-			if (ret)
-				return ret;
 		}
 		break;
 
@@ -851,13 +849,6 @@
 		break;
 	}
 
-	/* driver/net/can/dev.c:can_restart() takes in account error
-	 * messages in the RX stats. Doing the same here for
-	 * consistency.
-	 */
-	netdev->stats.rx_packets++;
-	netdev->stats.rx_bytes += CAN_ERR_DLC;
-
 	if (cf) {
 		if (cf->data[1])
 			cf->can_id |= CAN_ERR_CRTL;
@@ -881,7 +872,7 @@
 					ES58X_EVENT_BUSOFF, timestamp);
 	}
 
-	return 0;
+	return ret;
 }
 
 /**
@@ -1796,7 +1787,7 @@
 	struct es58x_device *es58x_dev = es58x_priv(netdev)->es58x_dev;
 	int ret;
 
-	if (atomic_inc_return(&es58x_dev->opened_channel_cnt) == 1) {
+	if (!es58x_dev->opened_channel_cnt) {
 		ret = es58x_alloc_rx_urbs(es58x_dev);
 		if (ret)
 			return ret;
@@ -1814,12 +1805,13 @@
 	if (ret)
 		goto free_urbs;
 
+	es58x_dev->opened_channel_cnt++;
 	netif_start_queue(netdev);
 
 	return ret;
 
  free_urbs:
-	if (atomic_dec_and_test(&es58x_dev->opened_channel_cnt))
+	if (!es58x_dev->opened_channel_cnt)
 		es58x_free_urbs(es58x_dev);
 	netdev_err(netdev, "%s: Could not open the network device: %pe\n",
 		   __func__, ERR_PTR(ret));
@@ -1854,7 +1846,8 @@
 
 	es58x_flush_pending_tx_msg(netdev);
 
-	if (atomic_dec_and_test(&es58x_dev->opened_channel_cnt))
+	es58x_dev->opened_channel_cnt--;
+	if (!es58x_dev->opened_channel_cnt)
 		es58x_free_urbs(es58x_dev);
 
 	return 0;
@@ -2098,8 +2091,11 @@
 	netdev->flags |= IFF_ECHO;	/* We support local echo */
 
 	ret = register_candev(netdev);
-	if (ret)
+	if (ret) {
+		es58x_dev->netdev[channel_idx] = NULL;
+		free_candev(netdev);
 		return ret;
+	}
 
 	netdev_queue_set_dql_min_limit(netdev_get_tx_queue(netdev, 0),
 				       es58x_dev->param->dql_min_limit);
@@ -2223,7 +2219,6 @@
 	init_usb_anchor(&es58x_dev->tx_urbs_idle);
 	init_usb_anchor(&es58x_dev->tx_urbs_busy);
 	atomic_set(&es58x_dev->tx_urbs_idle_cnt, 0);
-	atomic_set(&es58x_dev->opened_channel_cnt, 0);
 	usb_set_intfdata(intf, es58x_dev);
 
 	es58x_dev->rx_pipe = usb_rcvbulkpipe(es58x_dev->udev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/etas_es58x/es58x_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/etas_es58x/es58x_core.h
@@ -373,8 +373,6 @@
  *	queue wake/stop logic should prevent this URB from getting
  *	empty. Please refer to es58x_get_tx_urb() for more details.
  * @tx_urbs_idle_cnt: number of urbs in @tx_urbs_idle.
- * @opened_channel_cnt: number of channels opened (c.f. es58x_open()
- *	and es58x_stop()).
  * @ktime_req_ns: kernel timestamp when es58x_set_realtime_diff_ns()
  *	was called.
  * @realtime_diff_ns: difference in nanoseconds between the clocks of
@@ -384,6 +382,10 @@
  *	in RX branches.
  * @rx_max_packet_size: Maximum length of bulk-in URB.
  * @num_can_ch: Number of CAN channel (i.e. number of elements of @netdev).
+ * @opened_channel_cnt: number of channels opened. Free of race
+ *	conditions because its two users (net_device_ops:ndo_open()
+ *	and net_device_ops:ndo_close()) guarantee that the network
+ *	stack big kernel lock (a.k.a. rtnl_mutex) is being hold.
  * @rx_cmd_buf_len: Length of @rx_cmd_buf.
  * @rx_cmd_buf: The device might split the URB commands in an
  *	arbitrary amount of pieces. This buffer is used to concatenate
@@ -406,7 +408,6 @@
 	struct usb_anchor tx_urbs_busy;
 	struct usb_anchor tx_urbs_idle;
 	atomic_t tx_urbs_idle_cnt;
-	atomic_t opened_channel_cnt;
 
 	u64 ktime_req_ns;
 	s64 realtime_diff_ns;
@@ -415,6 +416,7 @@
 
 	u16 rx_max_packet_size;
 	u8 num_can_ch;
+	u8 opened_channel_cnt;
 
 	u16 rx_cmd_buf_len;
 	union es58x_urb_cmd rx_cmd_buf;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/etas_es58x/es58x_fd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/etas_es58x/es58x_fd.c
@@ -171,12 +171,11 @@
 	const struct es58x_fd_rx_event_msg *rx_event_msg;
 	int ret;
 
+	rx_event_msg = &es58x_fd_urb_cmd->rx_event_msg;
 	ret = es58x_check_msg_len(es58x_dev->dev, *rx_event_msg, msg_len);
 	if (ret)
 		return ret;
 
-	rx_event_msg = &es58x_fd_urb_cmd->rx_event_msg;
-
 	return es58x_rx_err_msg(netdev, rx_event_msg->error_code,
 				rx_event_msg->event_code,
 				get_unaligned_le64(&rx_event_msg->timestamp));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/f81604.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/f81604.c
@@ -0,0 +1,1204 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Fintek F81604 USB-to-2CAN controller driver.
+ *
+ * Copyright (C) 2023 Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
+ */
+#include <linux/bitfield.h>
+#include <linux/netdevice.h>
+#include <linux/units.h>
+#include <linux/usb.h>
+
+#include <linux/ethtool.h>
+
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+#include <linux/can/platform/sja1000.h>
+
+#include <asm-generic/unaligned.h>
+
+/* vendor and product id */
+#define F81604_VENDOR_ID 0x2c42
+#define F81604_PRODUCT_ID 0x1709
+#define F81604_CAN_CLOCK (12 * MEGA)
+#define F81604_MAX_DEV 2
+#define F81604_SET_DEVICE_RETRY 10
+
+#define F81604_USB_TIMEOUT 2000
+#define F81604_SET_GET_REGISTER 0xA0
+#define F81604_PORT_OFFSET 0x1000
+#define F81604_MAX_RX_URBS 4
+
+#define F81604_CMD_DATA 0x00
+
+#define F81604_DLC_LEN_MASK GENMASK(3, 0)
+#define F81604_DLC_EFF_BIT BIT(7)
+#define F81604_DLC_RTR_BIT BIT(6)
+
+#define F81604_SFF_SHIFT 5
+#define F81604_EFF_SHIFT 3
+
+#define F81604_BRP_MASK GENMASK(5, 0)
+#define F81604_SJW_MASK GENMASK(7, 6)
+
+#define F81604_SEG1_MASK GENMASK(3, 0)
+#define F81604_SEG2_MASK GENMASK(6, 4)
+
+#define F81604_CLEAR_ALC 0
+#define F81604_CLEAR_ECC 1
+#define F81604_CLEAR_OVERRUN 2
+
+/* device setting */
+#define F81604_CTRL_MODE_REG 0x80
+#define F81604_TX_ONESHOT (0x03 << 3)
+#define F81604_TX_NORMAL (0x01 << 3)
+#define F81604_RX_AUTO_RELEASE_BUF BIT(1)
+#define F81604_INT_WHEN_CHANGE BIT(0)
+
+#define F81604_TERMINATOR_REG 0x105
+#define F81604_CAN0_TERM BIT(2)
+#define F81604_CAN1_TERM BIT(3)
+
+#define F81604_TERMINATION_DISABLED CAN_TERMINATION_DISABLED
+#define F81604_TERMINATION_ENABLED 120
+
+/* SJA1000 registers - manual section 6.4 (Pelican Mode) */
+#define F81604_SJA1000_MOD 0x00
+#define F81604_SJA1000_CMR 0x01
+#define F81604_SJA1000_IR 0x03
+#define F81604_SJA1000_IER 0x04
+#define F81604_SJA1000_ALC 0x0B
+#define F81604_SJA1000_ECC 0x0C
+#define F81604_SJA1000_RXERR 0x0E
+#define F81604_SJA1000_TXERR 0x0F
+#define F81604_SJA1000_ACCC0 0x10
+#define F81604_SJA1000_ACCM0 0x14
+#define F81604_MAX_FILTER_CNT 4
+
+/* Common registers - manual section 6.5 */
+#define F81604_SJA1000_BTR0 0x06
+#define F81604_SJA1000_BTR1 0x07
+#define F81604_SJA1000_BTR1_SAMPLE_TRIPLE BIT(7)
+#define F81604_SJA1000_OCR 0x08
+#define F81604_SJA1000_CDR 0x1F
+
+/* mode register */
+#define F81604_SJA1000_MOD_RM 0x01
+#define F81604_SJA1000_MOD_LOM 0x02
+#define F81604_SJA1000_MOD_STM 0x04
+
+/* commands */
+#define F81604_SJA1000_CMD_CDO 0x08
+
+/* interrupt sources */
+#define F81604_SJA1000_IRQ_BEI 0x80
+#define F81604_SJA1000_IRQ_ALI 0x40
+#define F81604_SJA1000_IRQ_EPI 0x20
+#define F81604_SJA1000_IRQ_DOI 0x08
+#define F81604_SJA1000_IRQ_EI 0x04
+#define F81604_SJA1000_IRQ_TI 0x02
+#define F81604_SJA1000_IRQ_RI 0x01
+#define F81604_SJA1000_IRQ_ALL 0xFF
+#define F81604_SJA1000_IRQ_OFF 0x00
+
+/* status register content */
+#define F81604_SJA1000_SR_BS 0x80
+#define F81604_SJA1000_SR_ES 0x40
+#define F81604_SJA1000_SR_TCS 0x08
+
+/* ECC register */
+#define F81604_SJA1000_ECC_SEG 0x1F
+#define F81604_SJA1000_ECC_DIR 0x20
+#define F81604_SJA1000_ECC_BIT 0x00
+#define F81604_SJA1000_ECC_FORM 0x40
+#define F81604_SJA1000_ECC_STUFF 0x80
+#define F81604_SJA1000_ECC_MASK 0xc0
+
+/* ALC register */
+#define F81604_SJA1000_ALC_MASK 0x1f
+#define CAN_ERR_CNT 0x00000200U
+
+/* table of devices that work with this driver */
+static const struct usb_device_id f81604_table[] = {
+	{ USB_DEVICE(F81604_VENDOR_ID, F81604_PRODUCT_ID) },
+	{} /* Terminating entry */
+};
+
+MODULE_DEVICE_TABLE(usb, f81604_table);
+
+static const struct ethtool_ops f81604_ethtool_ops = {
+	.get_ts_info = ethtool_op_get_ts_info,
+};
+
+static const u16 f81604_termination[] = { F81604_TERMINATION_DISABLED,
+					  F81604_TERMINATION_ENABLED };
+
+struct f81604_priv {
+	struct net_device *netdev[F81604_MAX_DEV];
+};
+
+struct f81604_port_priv {
+	struct can_priv can;
+	struct net_device *netdev;
+	struct sk_buff *echo_skb;
+
+	unsigned long clear_flags;
+	struct work_struct clear_reg_work;
+
+	struct usb_device *dev;
+	struct usb_interface *intf;
+
+	struct usb_anchor urbs_anchor;
+};
+
+/* Interrupt endpoint data format:
+ *	Byte 0: Status register.
+ *	Byte 1: Interrupt register.
+ *	Byte 2: Interrupt enable register.
+ *	Byte 3: Arbitration lost capture(ALC) register.
+ *	Byte 4: Error code capture(ECC) register.
+ *	Byte 5: Error warning limit register.
+ *	Byte 6: RX error counter register.
+ *	Byte 7: TX error counter register.
+ *	Byte 8: Reserved.
+ */
+struct f81604_int_data {
+	u8 sr;
+	u8 isrc;
+	u8 ier;
+	u8 alc;
+	u8 ecc;
+	u8 ewlr;
+	u8 rxerr;
+	u8 txerr;
+	u8 val;
+} __packed __aligned(4);
+
+struct f81604_sff {
+	__be16 id;
+	u8 data[CAN_MAX_DLEN];
+} __packed __aligned(2);
+
+struct f81604_eff {
+	__be32 id;
+	u8 data[CAN_MAX_DLEN];
+} __packed __aligned(2);
+
+struct f81604_can_frame {
+	u8 cmd;
+
+	/* According for F81604 DLC define:
+	 *	bit 3~0: data length (0~8)
+	 *	bit6: is RTR flag.
+	 *	bit7: is EFF frame.
+	 */
+	u8 dlc;
+
+	union {
+		struct f81604_sff sff;
+		struct f81604_eff eff;
+	};
+} __packed __aligned(2);
+
+static const u8 bulk_in_addr[F81604_MAX_DEV] = { 2, 4 };
+static const u8 bulk_out_addr[F81604_MAX_DEV] = { 1, 3 };
+static const u8 int_in_addr[F81604_MAX_DEV] = { 1, 3 };
+
+static int f81604_write(struct usb_device *dev, u16 reg, u8 data)
+{
+	int ret;
+
+	ret = usb_control_msg_send(dev, 0, F81604_SET_GET_REGISTER,
+				   USB_TYPE_VENDOR | USB_DIR_OUT, 0, reg,
+				   &data, sizeof(data), F81604_USB_TIMEOUT,
+				   GFP_KERNEL);
+	if (ret)
+		dev_err(&dev->dev, "%s: reg: %x data: %x failed: %pe\n",
+			__func__, reg, data, ERR_PTR(ret));
+
+	return ret;
+}
+
+static int f81604_read(struct usb_device *dev, u16 reg, u8 *data)
+{
+	int ret;
+
+	ret = usb_control_msg_recv(dev, 0, F81604_SET_GET_REGISTER,
+				   USB_TYPE_VENDOR | USB_DIR_IN, 0, reg, data,
+				   sizeof(*data), F81604_USB_TIMEOUT,
+				   GFP_KERNEL);
+
+	if (ret < 0)
+		dev_err(&dev->dev, "%s: reg: %x failed: %pe\n", __func__, reg,
+			ERR_PTR(ret));
+
+	return ret;
+}
+
+static int f81604_update_bits(struct usb_device *dev, u16 reg, u8 mask,
+			      u8 data)
+{
+	int ret;
+	u8 tmp;
+
+	ret = f81604_read(dev, reg, &tmp);
+	if (ret)
+		return ret;
+
+	tmp &= ~mask;
+	tmp |= (mask & data);
+
+	return f81604_write(dev, reg, tmp);
+}
+
+static int f81604_sja1000_write(struct f81604_port_priv *priv, u16 reg,
+				u8 data)
+{
+	int port = priv->netdev->dev_port;
+	int real_reg;
+
+	real_reg = reg + F81604_PORT_OFFSET * port + F81604_PORT_OFFSET;
+	return f81604_write(priv->dev, real_reg, data);
+}
+
+static int f81604_sja1000_read(struct f81604_port_priv *priv, u16 reg,
+			       u8 *data)
+{
+	int port = priv->netdev->dev_port;
+	int real_reg;
+
+	real_reg = reg + F81604_PORT_OFFSET * port + F81604_PORT_OFFSET;
+	return f81604_read(priv->dev, real_reg, data);
+}
+
+static int f81604_set_reset_mode(struct f81604_port_priv *priv)
+{
+	int ret, i;
+	u8 tmp;
+
+	/* disable interrupts */
+	ret = f81604_sja1000_write(priv, F81604_SJA1000_IER,
+				   F81604_SJA1000_IRQ_OFF);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < F81604_SET_DEVICE_RETRY; i++) {
+		ret = f81604_sja1000_read(priv, F81604_SJA1000_MOD, &tmp);
+		if (ret)
+			return ret;
+
+		/* check reset bit */
+		if (tmp & F81604_SJA1000_MOD_RM) {
+			priv->can.state = CAN_STATE_STOPPED;
+			return 0;
+		}
+
+		/* reset chip */
+		ret = f81604_sja1000_write(priv, F81604_SJA1000_MOD,
+					   F81604_SJA1000_MOD_RM);
+		if (ret)
+			return ret;
+	}
+
+	return -EPERM;
+}
+
+static int f81604_set_normal_mode(struct f81604_port_priv *priv)
+{
+	u8 tmp, ier = 0;
+	u8 mod_reg = 0;
+	int ret, i;
+
+	for (i = 0; i < F81604_SET_DEVICE_RETRY; i++) {
+		ret = f81604_sja1000_read(priv, F81604_SJA1000_MOD, &tmp);
+		if (ret)
+			return ret;
+
+		/* check reset bit */
+		if ((tmp & F81604_SJA1000_MOD_RM) == 0) {
+			priv->can.state = CAN_STATE_ERROR_ACTIVE;
+			/* enable interrupts, RI handled by bulk-in */
+			ier = F81604_SJA1000_IRQ_ALL & ~F81604_SJA1000_IRQ_RI;
+			if (!(priv->can.ctrlmode &
+			      CAN_CTRLMODE_BERR_REPORTING))
+				ier &= ~F81604_SJA1000_IRQ_BEI;
+
+			return f81604_sja1000_write(priv, F81604_SJA1000_IER,
+						    ier);
+		}
+
+		/* set chip to normal mode */
+		if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)
+			mod_reg |= F81604_SJA1000_MOD_LOM;
+		if (priv->can.ctrlmode & CAN_CTRLMODE_PRESUME_ACK)
+			mod_reg |= F81604_SJA1000_MOD_STM;
+
+		ret = f81604_sja1000_write(priv, F81604_SJA1000_MOD, mod_reg);
+		if (ret)
+			return ret;
+	}
+
+	return -EPERM;
+}
+
+static int f81604_chipset_init(struct f81604_port_priv *priv)
+{
+	int i, ret;
+
+	/* set clock divider and output control register */
+	ret = f81604_sja1000_write(priv, F81604_SJA1000_CDR,
+				   CDR_CBP | CDR_PELICAN);
+	if (ret)
+		return ret;
+
+	/* set acceptance filter (accept all) */
+	for (i = 0; i < F81604_MAX_FILTER_CNT; ++i) {
+		ret = f81604_sja1000_write(priv, F81604_SJA1000_ACCC0 + i, 0);
+		if (ret)
+			return ret;
+	}
+
+	for (i = 0; i < F81604_MAX_FILTER_CNT; ++i) {
+		ret = f81604_sja1000_write(priv, F81604_SJA1000_ACCM0 + i,
+					   0xFF);
+		if (ret)
+			return ret;
+	}
+
+	return f81604_sja1000_write(priv, F81604_SJA1000_OCR,
+				    OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL |
+					    OCR_MODE_NORMAL);
+}
+
+static void f81604_process_rx_packet(struct net_device *netdev,
+				     struct f81604_can_frame *frame)
+{
+	struct net_device_stats *stats = &netdev->stats;
+	struct can_frame *cf;
+	struct sk_buff *skb;
+
+	if (frame->cmd != F81604_CMD_DATA)
+		return;
+
+	skb = alloc_can_skb(netdev, &cf);
+	if (!skb) {
+		stats->rx_dropped++;
+		return;
+	}
+
+	cf->len = can_cc_dlc2len(frame->dlc & F81604_DLC_LEN_MASK);
+
+	if (frame->dlc & F81604_DLC_EFF_BIT) {
+		cf->can_id = get_unaligned_be32(&frame->eff.id) >>
+			     F81604_EFF_SHIFT;
+		cf->can_id |= CAN_EFF_FLAG;
+
+		if (!(frame->dlc & F81604_DLC_RTR_BIT))
+			memcpy(cf->data, frame->eff.data, cf->len);
+	} else {
+		cf->can_id = get_unaligned_be16(&frame->sff.id) >>
+			     F81604_SFF_SHIFT;
+
+		if (!(frame->dlc & F81604_DLC_RTR_BIT))
+			memcpy(cf->data, frame->sff.data, cf->len);
+	}
+
+	if (frame->dlc & F81604_DLC_RTR_BIT)
+		cf->can_id |= CAN_RTR_FLAG;
+	else
+		stats->rx_bytes += cf->len;
+
+	stats->rx_packets++;
+	netif_rx(skb);
+}
+
+static void f81604_read_bulk_callback(struct urb *urb)
+{
+	struct f81604_can_frame *frame = urb->transfer_buffer;
+	struct net_device *netdev = urb->context;
+	int ret;
+
+	if (!netif_device_present(netdev))
+		return;
+
+	if (urb->status)
+		netdev_info(netdev, "%s: URB aborted %pe\n", __func__,
+			    ERR_PTR(urb->status));
+
+	switch (urb->status) {
+	case 0: /* success */
+		break;
+
+	case -ENOENT:
+	case -EPIPE:
+	case -EPROTO:
+	case -ESHUTDOWN:
+		return;
+
+	default:
+		goto resubmit_urb;
+	}
+
+	if (urb->actual_length != sizeof(*frame)) {
+		netdev_warn(netdev, "URB length %u not equal to %zu\n",
+			    urb->actual_length, sizeof(*frame));
+		goto resubmit_urb;
+	}
+
+	f81604_process_rx_packet(netdev, frame);
+
+resubmit_urb:
+	ret = usb_submit_urb(urb, GFP_ATOMIC);
+	if (ret == -ENODEV)
+		netif_device_detach(netdev);
+	else if (ret)
+		netdev_err(netdev,
+			   "%s: failed to resubmit read bulk urb: %pe\n",
+			   __func__, ERR_PTR(ret));
+}
+
+static void f81604_handle_tx(struct f81604_port_priv *priv,
+			     struct f81604_int_data *data)
+{
+	struct net_device *netdev = priv->netdev;
+	struct net_device_stats *stats = &netdev->stats;
+
+	/* transmission buffer released */
+	if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT &&
+	    !(data->sr & F81604_SJA1000_SR_TCS)) {
+		stats->tx_errors++;
+		can_free_echo_skb(netdev, 0, NULL);
+	} else {
+		/* transmission complete */
+		stats->tx_bytes += can_get_echo_skb(netdev, 0, NULL);
+		stats->tx_packets++;
+	}
+
+	netif_wake_queue(netdev);
+}
+
+static void f81604_handle_can_bus_errors(struct f81604_port_priv *priv,
+					 struct f81604_int_data *data)
+{
+	enum can_state can_state = priv->can.state;
+	struct net_device *netdev = priv->netdev;
+	struct net_device_stats *stats = &netdev->stats;
+	struct can_frame *cf;
+	struct sk_buff *skb;
+
+	/* Note: ALC/ECC will not auto clear by read here, must be cleared by
+	 * read register (via clear_reg_work).
+	 */
+
+	skb = alloc_can_err_skb(netdev, &cf);
+	if (skb) {
+		cf->can_id |= CAN_ERR_CNT;
+		cf->data[6] = data->txerr;
+		cf->data[7] = data->rxerr;
+	}
+
+	if (data->isrc & F81604_SJA1000_IRQ_DOI) {
+		/* data overrun interrupt */
+		netdev_dbg(netdev, "data overrun interrupt\n");
+
+		if (skb) {
+			cf->can_id |= CAN_ERR_CRTL;
+			cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+		}
+
+		stats->rx_over_errors++;
+		stats->rx_errors++;
+
+		set_bit(F81604_CLEAR_OVERRUN, &priv->clear_flags);
+	}
+
+	if (data->isrc & F81604_SJA1000_IRQ_EI) {
+		/* error warning interrupt */
+		netdev_dbg(netdev, "error warning interrupt\n");
+
+		if (data->sr & F81604_SJA1000_SR_BS)
+			can_state = CAN_STATE_BUS_OFF;
+		else if (data->sr & F81604_SJA1000_SR_ES)
+			can_state = CAN_STATE_ERROR_WARNING;
+		else
+			can_state = CAN_STATE_ERROR_ACTIVE;
+	}
+
+	if (data->isrc & F81604_SJA1000_IRQ_BEI) {
+		/* bus error interrupt */
+		netdev_dbg(netdev, "bus error interrupt\n");
+
+		priv->can.can_stats.bus_error++;
+		stats->rx_errors++;
+
+		if (skb) {
+			cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+
+			/* set error type */
+			switch (data->ecc & F81604_SJA1000_ECC_MASK) {
+			case F81604_SJA1000_ECC_BIT:
+				cf->data[2] |= CAN_ERR_PROT_BIT;
+				break;
+			case F81604_SJA1000_ECC_FORM:
+				cf->data[2] |= CAN_ERR_PROT_FORM;
+				break;
+			case F81604_SJA1000_ECC_STUFF:
+				cf->data[2] |= CAN_ERR_PROT_STUFF;
+				break;
+			default:
+				break;
+			}
+
+			/* set error location */
+			cf->data[3] = data->ecc & F81604_SJA1000_ECC_SEG;
+
+			/* Error occurred during transmission? */
+			if ((data->ecc & F81604_SJA1000_ECC_DIR) == 0)
+				cf->data[2] |= CAN_ERR_PROT_TX;
+		}
+
+		set_bit(F81604_CLEAR_ECC, &priv->clear_flags);
+	}
+
+	if (data->isrc & F81604_SJA1000_IRQ_EPI) {
+		if (can_state == CAN_STATE_ERROR_PASSIVE)
+			can_state = CAN_STATE_ERROR_WARNING;
+		else
+			can_state = CAN_STATE_ERROR_PASSIVE;
+
+		/* error passive interrupt */
+		netdev_dbg(netdev, "error passive interrupt: %d\n", can_state);
+	}
+
+	if (data->isrc & F81604_SJA1000_IRQ_ALI) {
+		/* arbitration lost interrupt */
+		netdev_dbg(netdev, "arbitration lost interrupt\n");
+
+		priv->can.can_stats.arbitration_lost++;
+
+		if (skb) {
+			cf->can_id |= CAN_ERR_LOSTARB;
+			cf->data[0] = data->alc & F81604_SJA1000_ALC_MASK;
+		}
+
+		set_bit(F81604_CLEAR_ALC, &priv->clear_flags);
+	}
+
+	if (can_state != priv->can.state) {
+		enum can_state tx_state, rx_state;
+
+		tx_state = data->txerr >= data->rxerr ? can_state : 0;
+		rx_state = data->txerr <= data->rxerr ? can_state : 0;
+
+		can_change_state(netdev, cf, tx_state, rx_state);
+
+		if (can_state == CAN_STATE_BUS_OFF)
+			can_bus_off(netdev);
+	}
+
+	if (priv->clear_flags)
+		schedule_work(&priv->clear_reg_work);
+
+	if (skb)
+		netif_rx(skb);
+}
+
+static void f81604_read_int_callback(struct urb *urb)
+{
+	struct f81604_int_data *data = urb->transfer_buffer;
+	struct net_device *netdev = urb->context;
+	struct f81604_port_priv *priv;
+	int ret;
+
+	priv = netdev_priv(netdev);
+
+	if (!netif_device_present(netdev))
+		return;
+
+	if (urb->status)
+		netdev_info(netdev, "%s: Int URB aborted: %pe\n", __func__,
+			    ERR_PTR(urb->status));
+
+	switch (urb->status) {
+	case 0: /* success */
+		break;
+
+	case -ENOENT:
+	case -EPIPE:
+	case -EPROTO:
+	case -ESHUTDOWN:
+		return;
+
+	default:
+		goto resubmit_urb;
+	}
+
+	/* handle Errors */
+	if (data->isrc & (F81604_SJA1000_IRQ_DOI | F81604_SJA1000_IRQ_EI |
+			  F81604_SJA1000_IRQ_BEI | F81604_SJA1000_IRQ_EPI |
+			  F81604_SJA1000_IRQ_ALI))
+		f81604_handle_can_bus_errors(priv, data);
+
+	/* handle TX */
+	if (priv->can.state != CAN_STATE_BUS_OFF &&
+	    (data->isrc & F81604_SJA1000_IRQ_TI))
+		f81604_handle_tx(priv, data);
+
+resubmit_urb:
+	ret = usb_submit_urb(urb, GFP_ATOMIC);
+	if (ret == -ENODEV)
+		netif_device_detach(netdev);
+	else if (ret)
+		netdev_err(netdev, "%s: failed to resubmit int urb: %pe\n",
+			   __func__, ERR_PTR(ret));
+}
+
+static void f81604_unregister_urbs(struct f81604_port_priv *priv)
+{
+	usb_kill_anchored_urbs(&priv->urbs_anchor);
+}
+
+static int f81604_register_urbs(struct f81604_port_priv *priv)
+{
+	struct net_device *netdev = priv->netdev;
+	struct f81604_int_data *int_data;
+	int id = netdev->dev_port;
+	struct urb *int_urb;
+	int rx_urb_cnt;
+	int ret;
+
+	for (rx_urb_cnt = 0; rx_urb_cnt < F81604_MAX_RX_URBS; ++rx_urb_cnt) {
+		struct f81604_can_frame *frame;
+		struct urb *rx_urb;
+
+		rx_urb = usb_alloc_urb(0, GFP_KERNEL);
+		if (!rx_urb) {
+			ret = -ENOMEM;
+			break;
+		}
+
+		frame = kmalloc(sizeof(*frame), GFP_KERNEL);
+		if (!frame) {
+			usb_free_urb(rx_urb);
+			ret = -ENOMEM;
+			break;
+		}
+
+		usb_fill_bulk_urb(rx_urb, priv->dev,
+				  usb_rcvbulkpipe(priv->dev, bulk_in_addr[id]),
+				  frame, sizeof(*frame),
+				  f81604_read_bulk_callback, netdev);
+
+		rx_urb->transfer_flags |= URB_FREE_BUFFER;
+		usb_anchor_urb(rx_urb, &priv->urbs_anchor);
+
+		ret = usb_submit_urb(rx_urb, GFP_KERNEL);
+		if (ret) {
+			usb_unanchor_urb(rx_urb);
+			usb_free_urb(rx_urb);
+			break;
+		}
+
+		/* Drop reference, USB core will take care of freeing it */
+		usb_free_urb(rx_urb);
+	}
+
+	if (rx_urb_cnt == 0) {
+		netdev_warn(netdev, "%s: submit rx urb failed: %pe\n",
+			    __func__, ERR_PTR(ret));
+
+		goto error;
+	}
+
+	int_urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!int_urb) {
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	int_data = kmalloc(sizeof(*int_data), GFP_KERNEL);
+	if (!int_data) {
+		usb_free_urb(int_urb);
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	usb_fill_int_urb(int_urb, priv->dev,
+			 usb_rcvintpipe(priv->dev, int_in_addr[id]), int_data,
+			 sizeof(*int_data), f81604_read_int_callback, netdev,
+			 1);
+
+	int_urb->transfer_flags |= URB_FREE_BUFFER;
+	usb_anchor_urb(int_urb, &priv->urbs_anchor);
+
+	ret = usb_submit_urb(int_urb, GFP_KERNEL);
+	if (ret) {
+		usb_unanchor_urb(int_urb);
+		usb_free_urb(int_urb);
+
+		netdev_warn(netdev, "%s: submit int urb failed: %pe\n",
+			    __func__, ERR_PTR(ret));
+		goto error;
+	}
+
+	/* Drop reference, USB core will take care of freeing it */
+	usb_free_urb(int_urb);
+
+	return 0;
+
+error:
+	f81604_unregister_urbs(priv);
+	return ret;
+}
+
+static int f81604_start(struct net_device *netdev)
+{
+	struct f81604_port_priv *priv = netdev_priv(netdev);
+	int ret;
+	u8 mode;
+	u8 tmp;
+
+	mode = F81604_RX_AUTO_RELEASE_BUF | F81604_INT_WHEN_CHANGE;
+
+	/* Set TR/AT mode */
+	if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT)
+		mode |= F81604_TX_ONESHOT;
+	else
+		mode |= F81604_TX_NORMAL;
+
+	ret = f81604_sja1000_write(priv, F81604_CTRL_MODE_REG, mode);
+	if (ret)
+		return ret;
+
+	/* set reset mode */
+	ret = f81604_set_reset_mode(priv);
+	if (ret)
+		return ret;
+
+	ret = f81604_chipset_init(priv);
+	if (ret)
+		return ret;
+
+	/* Clear error counters and error code capture */
+	ret = f81604_sja1000_write(priv, F81604_SJA1000_TXERR, 0);
+	if (ret)
+		return ret;
+
+	ret = f81604_sja1000_write(priv, F81604_SJA1000_RXERR, 0);
+	if (ret)
+		return ret;
+
+	/* Read clear for ECC/ALC/IR register */
+	ret = f81604_sja1000_read(priv, F81604_SJA1000_ECC, &tmp);
+	if (ret)
+		return ret;
+
+	ret = f81604_sja1000_read(priv, F81604_SJA1000_ALC, &tmp);
+	if (ret)
+		return ret;
+
+	ret = f81604_sja1000_read(priv, F81604_SJA1000_IR, &tmp);
+	if (ret)
+		return ret;
+
+	ret = f81604_register_urbs(priv);
+	if (ret)
+		return ret;
+
+	ret = f81604_set_normal_mode(priv);
+	if (ret) {
+		f81604_unregister_urbs(priv);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int f81604_set_bittiming(struct net_device *dev)
+{
+	struct f81604_port_priv *priv = netdev_priv(dev);
+	struct can_bittiming *bt = &priv->can.bittiming;
+	u8 btr0, btr1;
+	int ret;
+
+	btr0 = FIELD_PREP(F81604_BRP_MASK, bt->brp - 1) |
+	       FIELD_PREP(F81604_SJW_MASK, bt->sjw - 1);
+
+	btr1 = FIELD_PREP(F81604_SEG1_MASK,
+			  bt->prop_seg + bt->phase_seg1 - 1) |
+	       FIELD_PREP(F81604_SEG2_MASK, bt->phase_seg2 - 1);
+
+	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
+		btr1 |= F81604_SJA1000_BTR1_SAMPLE_TRIPLE;
+
+	ret = f81604_sja1000_write(priv, F81604_SJA1000_BTR0, btr0);
+	if (ret) {
+		netdev_warn(dev, "%s: Set BTR0 failed: %pe\n", __func__,
+			    ERR_PTR(ret));
+		return ret;
+	}
+
+	ret = f81604_sja1000_write(priv, F81604_SJA1000_BTR1, btr1);
+	if (ret) {
+		netdev_warn(dev, "%s: Set BTR1 failed: %pe\n", __func__,
+			    ERR_PTR(ret));
+		return ret;
+	}
+
+	return 0;
+}
+
+static int f81604_set_mode(struct net_device *netdev, enum can_mode mode)
+{
+	int ret;
+
+	switch (mode) {
+	case CAN_MODE_START:
+		ret = f81604_start(netdev);
+		if (!ret && netif_queue_stopped(netdev))
+			netif_wake_queue(netdev);
+		break;
+
+	default:
+		ret = -EOPNOTSUPP;
+	}
+
+	return ret;
+}
+
+static void f81604_write_bulk_callback(struct urb *urb)
+{
+	struct net_device *netdev = urb->context;
+
+	if (!netif_device_present(netdev))
+		return;
+
+	if (urb->status)
+		netdev_info(netdev, "%s: Tx URB error: %pe\n", __func__,
+			    ERR_PTR(urb->status));
+}
+
+static void f81604_clear_reg_work(struct work_struct *work)
+{
+	struct f81604_port_priv *priv;
+	u8 tmp;
+
+	priv = container_of(work, struct f81604_port_priv, clear_reg_work);
+
+	/* dummy read for clear Arbitration lost capture(ALC) register. */
+	if (test_and_clear_bit(F81604_CLEAR_ALC, &priv->clear_flags))
+		f81604_sja1000_read(priv, F81604_SJA1000_ALC, &tmp);
+
+	/* dummy read for clear Error code capture(ECC) register. */
+	if (test_and_clear_bit(F81604_CLEAR_ECC, &priv->clear_flags))
+		f81604_sja1000_read(priv, F81604_SJA1000_ECC, &tmp);
+
+	/* dummy write for clear data overrun flag. */
+	if (test_and_clear_bit(F81604_CLEAR_OVERRUN, &priv->clear_flags))
+		f81604_sja1000_write(priv, F81604_SJA1000_CMR,
+				     F81604_SJA1000_CMD_CDO);
+}
+
+static netdev_tx_t f81604_start_xmit(struct sk_buff *skb,
+				     struct net_device *netdev)
+{
+	struct can_frame *cf = (struct can_frame *)skb->data;
+	struct f81604_port_priv *priv = netdev_priv(netdev);
+	struct net_device_stats *stats = &netdev->stats;
+	struct f81604_can_frame *frame;
+	struct urb *write_urb;
+	int ret;
+
+	if (can_dropped_invalid_skb(netdev, skb))
+		return NETDEV_TX_OK;
+
+	netif_stop_queue(netdev);
+
+	write_urb = usb_alloc_urb(0, GFP_ATOMIC);
+	if (!write_urb)
+		goto nomem_urb;
+
+	frame = kzalloc(sizeof(*frame), GFP_ATOMIC);
+	if (!frame)
+		goto nomem_buf;
+
+	usb_fill_bulk_urb(write_urb, priv->dev,
+			  usb_sndbulkpipe(priv->dev,
+					  bulk_out_addr[netdev->dev_port]),
+			  frame, sizeof(*frame), f81604_write_bulk_callback,
+			  priv->netdev);
+
+	write_urb->transfer_flags |= URB_FREE_BUFFER;
+
+	frame->cmd = F81604_CMD_DATA;
+	frame->dlc = cf->len;
+
+	if (cf->can_id & CAN_RTR_FLAG)
+		frame->dlc |= F81604_DLC_RTR_BIT;
+
+	if (cf->can_id & CAN_EFF_FLAG) {
+		u32 id = (cf->can_id & CAN_EFF_MASK) << F81604_EFF_SHIFT;
+
+		put_unaligned_be32(id, &frame->eff.id);
+
+		frame->dlc |= F81604_DLC_EFF_BIT;
+
+		if (!(cf->can_id & CAN_RTR_FLAG))
+			memcpy(&frame->eff.data, cf->data, cf->len);
+	} else {
+		u32 id = (cf->can_id & CAN_SFF_MASK) << F81604_SFF_SHIFT;
+
+		put_unaligned_be16(id, &frame->sff.id);
+
+		if (!(cf->can_id & CAN_RTR_FLAG))
+			memcpy(&frame->sff.data, cf->data, cf->len);
+	}
+
+	can_put_echo_skb(skb, netdev, 0, 0);
+
+	ret = usb_submit_urb(write_urb, GFP_ATOMIC);
+	if (ret) {
+		netdev_err(netdev, "%s: failed to resubmit tx bulk urb: %pe\n",
+			   __func__, ERR_PTR(ret));
+
+		can_free_echo_skb(netdev, 0, NULL);
+		stats->tx_dropped++;
+		stats->tx_errors++;
+
+		if (ret == -ENODEV)
+			netif_device_detach(netdev);
+		else
+			netif_wake_queue(netdev);
+	}
+
+	/* let usb core take care of this urb */
+	usb_free_urb(write_urb);
+
+	return NETDEV_TX_OK;
+
+nomem_buf:
+	usb_free_urb(write_urb);
+
+nomem_urb:
+	dev_kfree_skb(skb);
+	stats->tx_dropped++;
+	stats->tx_errors++;
+	netif_wake_queue(netdev);
+
+	return NETDEV_TX_OK;
+}
+
+static int f81604_get_berr_counter(const struct net_device *netdev,
+				   struct can_berr_counter *bec)
+{
+	struct f81604_port_priv *priv = netdev_priv(netdev);
+	u8 txerr, rxerr;
+	int ret;
+
+	ret = f81604_sja1000_read(priv, F81604_SJA1000_TXERR, &txerr);
+	if (ret)
+		return ret;
+
+	ret = f81604_sja1000_read(priv, F81604_SJA1000_RXERR, &rxerr);
+	if (ret)
+		return ret;
+
+	bec->txerr = txerr;
+	bec->rxerr = rxerr;
+
+	return 0;
+}
+
+/* Open USB device */
+static int f81604_open(struct net_device *netdev)
+{
+	int ret;
+
+	ret = open_candev(netdev);
+	if (ret)
+		return ret;
+
+	ret = f81604_start(netdev);
+	if (ret) {
+		if (ret == -ENODEV)
+			netif_device_detach(netdev);
+
+		close_candev(netdev);
+		return ret;
+	}
+
+	netif_start_queue(netdev);
+	return 0;
+}
+
+/* Close USB device */
+static int f81604_close(struct net_device *netdev)
+{
+	struct f81604_port_priv *priv = netdev_priv(netdev);
+
+	f81604_set_reset_mode(priv);
+
+	netif_stop_queue(netdev);
+	cancel_work_sync(&priv->clear_reg_work);
+	close_candev(netdev);
+
+	f81604_unregister_urbs(priv);
+
+	return 0;
+}
+
+static const struct net_device_ops f81604_netdev_ops = {
+	.ndo_open = f81604_open,
+	.ndo_stop = f81604_close,
+	.ndo_start_xmit = f81604_start_xmit,
+	.ndo_change_mtu = can_change_mtu,
+};
+
+static const struct can_bittiming_const f81604_bittiming_const = {
+	.name = KBUILD_MODNAME,
+	.tseg1_min = 1,
+	.tseg1_max = 16,
+	.tseg2_min = 1,
+	.tseg2_max = 8,
+	.sjw_max = 4,
+	.brp_min = 1,
+	.brp_max = 64,
+	.brp_inc = 1,
+};
+
+/* Called by the usb core when driver is unloaded or device is removed */
+static void f81604_disconnect(struct usb_interface *intf)
+{
+	struct f81604_priv *priv = usb_get_intfdata(intf);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) {
+		if (!priv->netdev[i])
+			continue;
+
+		unregister_netdev(priv->netdev[i]);
+		free_candev(priv->netdev[i]);
+	}
+}
+
+static int __f81604_set_termination(struct usb_device *dev, int idx, u16 term)
+{
+	u8 mask, data = 0;
+
+	if (idx == 0)
+		mask = F81604_CAN0_TERM;
+	else
+		mask = F81604_CAN1_TERM;
+
+	if (term)
+		data = mask;
+
+	return f81604_update_bits(dev, F81604_TERMINATOR_REG, mask, data);
+}
+
+static int f81604_set_termination(struct net_device *netdev, u16 term)
+{
+	struct f81604_port_priv *port_priv = netdev_priv(netdev);
+
+	ASSERT_RTNL();
+
+	return __f81604_set_termination(port_priv->dev, netdev->dev_port,
+					term);
+}
+
+static int f81604_probe(struct usb_interface *intf,
+			const struct usb_device_id *id)
+{
+	struct usb_device *dev = interface_to_usbdev(intf);
+	struct net_device *netdev;
+	struct f81604_priv *priv;
+	int i, ret;
+
+	priv = devm_kzalloc(&intf->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	usb_set_intfdata(intf, priv);
+
+	for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) {
+		ret = __f81604_set_termination(dev, i, 0);
+		if (ret) {
+			dev_err(&intf->dev,
+				"Setting termination of CH#%d failed: %pe\n",
+				i, ERR_PTR(ret));
+			return ret;
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) {
+		struct f81604_port_priv *port_priv;
+
+		netdev = alloc_candev(sizeof(*port_priv), 1);
+		if (!netdev) {
+			dev_err(&intf->dev, "Couldn't alloc candev: %d\n", i);
+			ret = -ENOMEM;
+
+			goto failure_cleanup;
+		}
+
+		port_priv = netdev_priv(netdev);
+
+		INIT_WORK(&port_priv->clear_reg_work, f81604_clear_reg_work);
+		init_usb_anchor(&port_priv->urbs_anchor);
+
+		port_priv->intf = intf;
+		port_priv->dev = dev;
+		port_priv->netdev = netdev;
+		port_priv->can.clock.freq = F81604_CAN_CLOCK;
+
+		port_priv->can.termination_const = f81604_termination;
+		port_priv->can.termination_const_cnt =
+			ARRAY_SIZE(f81604_termination);
+		port_priv->can.bittiming_const = &f81604_bittiming_const;
+		port_priv->can.do_set_bittiming = f81604_set_bittiming;
+		port_priv->can.do_set_mode = f81604_set_mode;
+		port_priv->can.do_set_termination = f81604_set_termination;
+		port_priv->can.do_get_berr_counter = f81604_get_berr_counter;
+		port_priv->can.ctrlmode_supported =
+			CAN_CTRLMODE_LISTENONLY | CAN_CTRLMODE_3_SAMPLES |
+			CAN_CTRLMODE_ONE_SHOT | CAN_CTRLMODE_BERR_REPORTING |
+			CAN_CTRLMODE_PRESUME_ACK;
+
+		netdev->ethtool_ops = &f81604_ethtool_ops;
+		netdev->netdev_ops = &f81604_netdev_ops;
+		netdev->flags |= IFF_ECHO;
+		netdev->dev_port = i;
+
+		SET_NETDEV_DEV(netdev, &intf->dev);
+
+		ret = register_candev(netdev);
+		if (ret) {
+			netdev_err(netdev, "register CAN device failed: %pe\n",
+				   ERR_PTR(ret));
+			free_candev(netdev);
+
+			goto failure_cleanup;
+		}
+
+		priv->netdev[i] = netdev;
+	}
+
+	return 0;
+
+failure_cleanup:
+	f81604_disconnect(intf);
+	return ret;
+}
+
+static struct usb_driver f81604_driver = {
+	.name = KBUILD_MODNAME,
+	.probe = f81604_probe,
+	.disconnect = f81604_disconnect,
+	.id_table = f81604_table,
+};
+
+module_usb_driver(f81604_driver);
+
+MODULE_AUTHOR("Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>");
+MODULE_DESCRIPTION("Fintek F81604 USB to 2xCANBUS");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/gs_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/gs_usb.c
@@ -185,14 +185,16 @@
 
 	struct usb_anchor tx_submitted;
 	atomic_t active_tx_urbs;
+	void *rxbuf[GS_MAX_RX_URBS];
+	dma_addr_t rxbuf_dma[GS_MAX_RX_URBS];
 };
 
 /* usb interface struct */
 struct gs_usb {
 	struct gs_can *canch[GS_MAX_INTF];
 	struct usb_anchor rx_submitted;
-	atomic_t active_channels;
 	struct usb_device *udev;
+	u8 active_channels;
 };
 
 /* 'allocate' a tx context.
@@ -321,7 +323,7 @@
 
 	/* device reports out of range channel id */
 	if (hf->channel >= GS_MAX_INTF)
-		goto resubmit_urb;
+		goto device_detach;
 
 	dev = usbcan->canch[hf->channel];
 
@@ -380,6 +382,9 @@
 	}
 
 	if (hf->flags & GS_CAN_FLAG_OVERFLOW) {
+		stats->rx_over_errors++;
+		stats->rx_errors++;
+
 		skb = alloc_can_err_skb(netdev, &cf);
 		if (!skb)
 			goto resubmit_urb;
@@ -387,8 +392,6 @@
 		cf->can_id |= CAN_ERR_CRTL;
 		cf->len = CAN_ERR_DLC;
 		cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
-		stats->rx_over_errors++;
-		stats->rx_errors++;
 		netif_rx(skb);
 	}
 
@@ -406,6 +409,7 @@
 
 	/* USB failure take down all interfaces */
 	if (rc == -ENODEV) {
+ device_detach:
 		for (rc = 0; rc < GS_MAX_INTF; rc++) {
 			if (usbcan->canch[rc])
 				netif_device_detach(usbcan->canch[rc]->netdev);
@@ -507,6 +511,8 @@
 
 	hf->echo_id = idx;
 	hf->channel = dev->channel;
+	hf->flags = 0;
+	hf->reserved = 0;
 
 	cf = (struct can_frame *)skb->data;
 
@@ -587,10 +593,11 @@
 	if (rc)
 		return rc;
 
-	if (atomic_add_return(1, &parent->active_channels) == 1) {
+	if (!parent->active_channels) {
 		for (i = 0; i < GS_MAX_RX_URBS; i++) {
 			struct urb *urb;
 			u8 *buf;
+			dma_addr_t buf_dma;
 
 			/* alloc rx urb */
 			urb = usb_alloc_urb(0, GFP_KERNEL);
@@ -601,7 +608,7 @@
 			buf = usb_alloc_coherent(dev->udev,
 						 sizeof(struct gs_host_frame),
 						 GFP_KERNEL,
-						 &urb->transfer_dma);
+						 &buf_dma);
 			if (!buf) {
 				netdev_err(netdev,
 					   "No memory left for USB buffer\n");
@@ -609,6 +616,8 @@
 				return -ENOMEM;
 			}
 
+			urb->transfer_dma = buf_dma;
+
 			/* fill, anchor, and submit rx urb */
 			usb_fill_bulk_urb(urb,
 					  dev->udev,
@@ -632,10 +641,17 @@
 					   rc);
 
 				usb_unanchor_urb(urb);
+				usb_free_coherent(dev->udev,
+						  sizeof(struct gs_host_frame),
+						  buf,
+						  buf_dma);
 				usb_free_urb(urb);
 				break;
 			}
 
+			dev->rxbuf[i] = buf;
+			dev->rxbuf_dma[i] = buf_dma;
+
 			/* Drop reference,
 			 * USB core will take care of freeing it
 			 */
@@ -665,6 +681,7 @@
 		flags |= GS_CAN_MODE_TRIPLE_SAMPLE;
 
 	/* finally start device */
+	dev->can.state = CAN_STATE_ERROR_ACTIVE;
 	dm->mode = cpu_to_le32(GS_CAN_MODE_START);
 	dm->flags = cpu_to_le32(flags);
 	rc = usb_control_msg(interface_to_usbdev(dev->iface),
@@ -681,13 +698,13 @@
 	if (rc < 0) {
 		netdev_err(netdev, "Couldn't start device (err=%d)\n", rc);
 		kfree(dm);
+		dev->can.state = CAN_STATE_STOPPED;
 		return rc;
 	}
 
 	kfree(dm);
 
-	dev->can.state = CAN_STATE_ERROR_ACTIVE;
-
+	parent->active_channels++;
 	if (!(dev->can.ctrlmode & CAN_CTRLMODE_LISTENONLY))
 		netif_start_queue(netdev);
 
@@ -699,17 +716,27 @@
 	int rc;
 	struct gs_can *dev = netdev_priv(netdev);
 	struct gs_usb *parent = dev->parent;
+	unsigned int i;
 
 	netif_stop_queue(netdev);
 
 	/* Stop polling */
-	if (atomic_dec_and_test(&parent->active_channels))
+	parent->active_channels--;
+	if (!parent->active_channels) {
 		usb_kill_anchored_urbs(&parent->rx_submitted);
+		for (i = 0; i < GS_MAX_RX_URBS; i++)
+			usb_free_coherent(dev->udev,
+					  sizeof(struct gs_host_frame),
+					  dev->rxbuf[i],
+					  dev->rxbuf_dma[i]);
+	}
 
 	/* Stop sending URBs */
 	usb_kill_anchored_urbs(&dev->tx_submitted);
 	atomic_set(&dev->active_tx_urbs, 0);
 
+	dev->can.state = CAN_STATE_STOPPED;
+
 	/* reset the device */
 	rc = gs_cmd_reset(dev);
 	if (rc < 0)
@@ -982,8 +1009,6 @@
 
 	init_usb_anchor(&dev->rx_submitted);
 
-	atomic_set(&dev->active_channels, 0);
-
 	usb_set_intfdata(intf, dev);
 	dev->udev = interface_to_usbdev(intf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/kvaser_usb/kvaser_usb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/kvaser_usb/kvaser_usb.h
@@ -35,9 +35,10 @@
 #define KVASER_USB_RX_BUFFER_SIZE		3072
 #define KVASER_USB_MAX_NET_DEVICES		5
 
-/* USB devices features */
-#define KVASER_USB_HAS_SILENT_MODE		BIT(0)
-#define KVASER_USB_HAS_TXRX_ERRORS		BIT(1)
+/* Kvaser USB device quirks */
+#define KVASER_USB_QUIRK_HAS_SILENT_MODE	BIT(0)
+#define KVASER_USB_QUIRK_HAS_TXRX_ERRORS	BIT(1)
+#define KVASER_USB_QUIRK_IGNORE_CLK_FREQ	BIT(2)
 
 /* Device capabilities */
 #define KVASER_USB_CAP_BERR_CAP			0x01
@@ -65,12 +66,7 @@
 struct kvaser_usb_dev_card_data {
 	u32 ctrlmode_supported;
 	u32 capabilities;
-	union {
-		struct {
-			enum kvaser_usb_leaf_family family;
-		} leaf;
-		struct kvaser_usb_dev_card_data_hydra hydra;
-	};
+	struct kvaser_usb_dev_card_data_hydra hydra;
 };
 
 /* Context for an outstanding, not yet ACKed, transmission */
@@ -80,11 +76,19 @@
 	int dlc;
 };
 
+struct kvaser_usb_busparams {
+	__le32 bitrate;
+	u8 tseg1;
+	u8 tseg2;
+	u8 sjw;
+	u8 nsamples;
+} __packed;
+
 struct kvaser_usb {
 	struct usb_device *udev;
 	struct usb_interface *intf;
 	struct kvaser_usb_net_priv *nets[KVASER_USB_MAX_NET_DEVICES];
-	const struct kvaser_usb_dev_ops *ops;
+	const struct kvaser_usb_driver_info *driver_info;
 	const struct kvaser_usb_dev_cfg *cfg;
 
 	struct usb_endpoint_descriptor *bulk_in, *bulk_out;
@@ -108,13 +112,19 @@
 	struct can_priv can;
 	struct can_berr_counter bec;
 
+	/* subdriver-specific data */
+	void *sub_priv;
+
 	struct kvaser_usb *dev;
 	struct net_device *netdev;
 	int channel;
 
-	struct completion start_comp, stop_comp, flush_comp;
+	struct completion start_comp, stop_comp, flush_comp,
+			  get_busparams_comp;
 	struct usb_anchor tx_submitted;
 
+	struct kvaser_usb_busparams busparams_nominal, busparams_data;
+
 	spinlock_t tx_contexts_lock; /* lock for active_tx_contexts */
 	int active_tx_contexts;
 	struct kvaser_usb_tx_urb_context tx_contexts[];
@@ -124,11 +134,15 @@
  * struct kvaser_usb_dev_ops - Device specific functions
  * @dev_set_mode:		used for can.do_set_mode
  * @dev_set_bittiming:		used for can.do_set_bittiming
+ * @dev_get_busparams:		readback arbitration busparams
  * @dev_set_data_bittiming:	used for can.do_set_data_bittiming
+ * @dev_get_data_busparams:	readback data busparams
  * @dev_get_berr_counter:	used for can.do_get_berr_counter
  *
  * @dev_setup_endpoints:	setup USB in and out endpoints
  * @dev_init_card:		initialize card
+ * @dev_init_channel:		initialize channel
+ * @dev_remove_channel:		uninitialize channel
  * @dev_get_software_info:	get software info
  * @dev_get_software_details:	get software details
  * @dev_get_card_info:		get card info
@@ -144,12 +158,18 @@
  */
 struct kvaser_usb_dev_ops {
 	int (*dev_set_mode)(struct net_device *netdev, enum can_mode mode);
-	int (*dev_set_bittiming)(struct net_device *netdev);
-	int (*dev_set_data_bittiming)(struct net_device *netdev);
+	int (*dev_set_bittiming)(const struct net_device *netdev,
+				 const struct kvaser_usb_busparams *busparams);
+	int (*dev_get_busparams)(struct kvaser_usb_net_priv *priv);
+	int (*dev_set_data_bittiming)(const struct net_device *netdev,
+				      const struct kvaser_usb_busparams *busparams);
+	int (*dev_get_data_busparams)(struct kvaser_usb_net_priv *priv);
 	int (*dev_get_berr_counter)(const struct net_device *netdev,
 				    struct can_berr_counter *bec);
 	int (*dev_setup_endpoints)(struct kvaser_usb *dev);
 	int (*dev_init_card)(struct kvaser_usb *dev);
+	int (*dev_init_channel)(struct kvaser_usb_net_priv *priv);
+	void (*dev_remove_channel)(struct kvaser_usb_net_priv *priv);
 	int (*dev_get_software_info)(struct kvaser_usb *dev);
 	int (*dev_get_software_details)(struct kvaser_usb *dev);
 	int (*dev_get_card_info)(struct kvaser_usb *dev);
@@ -166,6 +186,12 @@
 				  int *cmd_len, u16 transid);
 };
 
+struct kvaser_usb_driver_info {
+	u32 quirks;
+	enum kvaser_usb_leaf_family family;
+	const struct kvaser_usb_dev_ops *ops;
+};
+
 struct kvaser_usb_dev_cfg {
 	const struct can_clock clock;
 	const unsigned int timestamp_freq;
@@ -176,6 +202,8 @@
 extern const struct kvaser_usb_dev_ops kvaser_usb_hydra_dev_ops;
 extern const struct kvaser_usb_dev_ops kvaser_usb_leaf_dev_ops;
 
+void kvaser_usb_unlink_tx_urbs(struct kvaser_usb_net_priv *priv);
+
 int kvaser_usb_recv_cmd(const struct kvaser_usb *dev, void *cmd, int len,
 			int *actual_len);
 
@@ -185,4 +213,7 @@
 			      int len);
 
 int kvaser_usb_can_rx_over_error(struct net_device *netdev);
+
+extern const struct can_bittiming_const kvaser_usb_flexc_bittiming_const;
+
 #endif /* KVASER_USB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
@@ -61,8 +61,6 @@
 #define USB_USBCAN_R_V2_PRODUCT_ID		294
 #define USB_LEAF_LIGHT_R_V2_PRODUCT_ID		295
 #define USB_LEAF_LIGHT_HS_V2_OEM2_PRODUCT_ID	296
-#define USB_LEAF_PRODUCT_ID_END \
-	USB_LEAF_LIGHT_HS_V2_OEM2_PRODUCT_ID
 
 /* Kvaser USBCan-II devices product ids */
 #define USB_USBCAN_REVB_PRODUCT_ID		2
@@ -89,116 +87,154 @@
 #define USB_USBCAN_PRO_4HS_PRODUCT_ID		276
 #define USB_HYBRID_CANLIN_PRODUCT_ID		277
 #define USB_HYBRID_PRO_CANLIN_PRODUCT_ID	278
-#define USB_HYDRA_PRODUCT_ID_END \
-	USB_HYBRID_PRO_CANLIN_PRODUCT_ID
 
-static inline bool kvaser_is_leaf(const struct usb_device_id *id)
-{
-	return (id->idProduct >= USB_LEAF_DEVEL_PRODUCT_ID &&
-		id->idProduct <= USB_CAN_R_PRODUCT_ID) ||
-		(id->idProduct >= USB_LEAF_LITE_V2_PRODUCT_ID &&
-		 id->idProduct <= USB_LEAF_PRODUCT_ID_END);
-}
+static const struct kvaser_usb_driver_info kvaser_usb_driver_info_hydra = {
+	.quirks = 0,
+	.ops = &kvaser_usb_hydra_dev_ops,
+};
 
-static inline bool kvaser_is_usbcan(const struct usb_device_id *id)
-{
-	return id->idProduct >= USB_USBCAN_REVB_PRODUCT_ID &&
-	       id->idProduct <= USB_MEMORATOR_PRODUCT_ID;
-}
+static const struct kvaser_usb_driver_info kvaser_usb_driver_info_usbcan = {
+	.quirks = KVASER_USB_QUIRK_HAS_TXRX_ERRORS |
+		  KVASER_USB_QUIRK_HAS_SILENT_MODE,
+	.family = KVASER_USBCAN,
+	.ops = &kvaser_usb_leaf_dev_ops,
+};
 
-static inline bool kvaser_is_hydra(const struct usb_device_id *id)
-{
-	return id->idProduct >= USB_BLACKBIRD_V2_PRODUCT_ID &&
-	       id->idProduct <= USB_HYDRA_PRODUCT_ID_END;
-}
+static const struct kvaser_usb_driver_info kvaser_usb_driver_info_leaf = {
+	.quirks = KVASER_USB_QUIRK_IGNORE_CLK_FREQ,
+	.family = KVASER_LEAF,
+	.ops = &kvaser_usb_leaf_dev_ops,
+};
+
+static const struct kvaser_usb_driver_info kvaser_usb_driver_info_leaf_err = {
+	.quirks = KVASER_USB_QUIRK_HAS_TXRX_ERRORS |
+		  KVASER_USB_QUIRK_IGNORE_CLK_FREQ,
+	.family = KVASER_LEAF,
+	.ops = &kvaser_usb_leaf_dev_ops,
+};
+
+static const struct kvaser_usb_driver_info kvaser_usb_driver_info_leaf_err_listen = {
+	.quirks = KVASER_USB_QUIRK_HAS_TXRX_ERRORS |
+		  KVASER_USB_QUIRK_HAS_SILENT_MODE |
+		  KVASER_USB_QUIRK_IGNORE_CLK_FREQ,
+	.family = KVASER_LEAF,
+	.ops = &kvaser_usb_leaf_dev_ops,
+};
+
+static const struct kvaser_usb_driver_info kvaser_usb_driver_info_leafimx = {
+	.quirks = 0,
+	.family = KVASER_LEAF,
+	.ops = &kvaser_usb_leaf_dev_ops,
+};
 
 static const struct usb_device_id kvaser_usb_table[] = {
-	/* Leaf USB product IDs */
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_DEVEL_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_PRODUCT_ID) },
+	/* Leaf M32C USB product IDs */
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_DEVEL_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_SPRO_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_LS_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_SWC_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_LIN_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_SPRO_LS_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_SPRO_SWC_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO2_DEVEL_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO2_HSHS_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_UPRO_HSHS_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_GI_PRODUCT_ID) },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_GI_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_OBDII_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS |
-			       KVASER_USB_HAS_SILENT_MODE },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err_listen },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO2_HSLS_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_CH_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_BLACKBIRD_SPRO_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_OEM_MERCURY_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_OEM_LEAF_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_CAN_R_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LIGHT_HS_V2_OEM_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_LIGHT_2HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_2HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_R_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LIGHT_R_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LIGHT_HS_V2_OEM2_PRODUCT_ID) },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leaf_err },
+
+	/* Leaf i.MX28 USB product IDs */
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LIGHT_HS_V2_OEM_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_LIGHT_2HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_2HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_R_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LIGHT_R_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LIGHT_HS_V2_OEM2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_leafimx },
 
 	/* USBCANII USB product IDs */
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN2_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_usbcan },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_REVB_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_usbcan },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMORATOR_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_usbcan },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_VCI2_PRODUCT_ID),
-		.driver_info = KVASER_USB_HAS_TXRX_ERRORS },
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_usbcan },
 
 	/* Minihydra USB product IDs */
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_BLACKBIRD_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO_PRO_5HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_PRO_5HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_LIGHT_4HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_HS_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_PRO_2HS_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO_2HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO_PRO_2HS_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_2CANLIN_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_ATI_USBCAN_PRO_2HS_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_ATI_MEMO_PRO_2HS_V2_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_PRO_2CANLIN_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_U100_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_U100P_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_U100S_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_PRO_4HS_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_CANLIN_PRODUCT_ID) },
-	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_PRO_CANLIN_PRODUCT_ID) },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_BLACKBIRD_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO_PRO_5HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_PRO_5HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_LIGHT_4HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_HS_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_PRO_2HS_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO_2HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMO_PRO_2HS_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_2CANLIN_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_ATI_USBCAN_PRO_2HS_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_ATI_MEMO_PRO_2HS_V2_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_PRO_2CANLIN_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_U100_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_U100P_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_U100S_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_PRO_4HS_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_CANLIN_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_HYBRID_PRO_CANLIN_PRODUCT_ID),
+		.driver_info = (kernel_ulong_t)&kvaser_usb_driver_info_hydra },
 	{ }
 };
 MODULE_DEVICE_TABLE(usb, kvaser_usb_table);
@@ -257,7 +293,7 @@
 	}
 	usb_free_urb(urb);
 
-	return 0;
+	return err;
 }
 
 int kvaser_usb_can_rx_over_error(struct net_device *netdev)
@@ -279,8 +315,6 @@
 	cf->can_id |= CAN_ERR_CRTL;
 	cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 
 	return 0;
@@ -289,6 +323,7 @@
 static void kvaser_usb_read_bulk_callback(struct urb *urb)
 {
 	struct kvaser_usb *dev = urb->context;
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
 	int err;
 	unsigned int i;
 
@@ -305,8 +340,8 @@
 		goto resubmit_urb;
 	}
 
-	dev->ops->dev_read_bulk_callback(dev, urb->transfer_buffer,
-					 urb->actual_length);
+	ops->dev_read_bulk_callback(dev, urb->transfer_buffer,
+				    urb->actual_length);
 
 resubmit_urb:
 	usb_fill_bulk_urb(urb, dev->udev,
@@ -400,21 +435,18 @@
 {
 	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
 	struct kvaser_usb *dev = priv->dev;
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
 	int err;
 
 	err = open_candev(netdev);
 	if (err)
 		return err;
 
-	err = kvaser_usb_setup_rx_urbs(dev);
+	err = ops->dev_set_opt_mode(priv);
 	if (err)
 		goto error;
 
-	err = dev->ops->dev_set_opt_mode(priv);
-	if (err)
-		goto error;
-
-	err = dev->ops->dev_start_chip(priv);
+	err = ops->dev_start_chip(priv);
 	if (err) {
 		netdev_warn(netdev, "Cannot start device, error %d\n", err);
 		goto error;
@@ -443,7 +475,7 @@
 /* This method might sleep. Do not call it in the atomic context
  * of URB completions.
  */
-static void kvaser_usb_unlink_tx_urbs(struct kvaser_usb_net_priv *priv)
+void kvaser_usb_unlink_tx_urbs(struct kvaser_usb_net_priv *priv)
 {
 	usb_kill_anchored_urbs(&priv->tx_submitted);
 	kvaser_usb_reset_tx_urb_contexts(priv);
@@ -471,22 +503,23 @@
 {
 	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
 	struct kvaser_usb *dev = priv->dev;
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
 	int err;
 
 	netif_stop_queue(netdev);
 
-	err = dev->ops->dev_flush_queue(priv);
+	err = ops->dev_flush_queue(priv);
 	if (err)
 		netdev_warn(netdev, "Cannot flush queue, error %d\n", err);
 
-	if (dev->ops->dev_reset_chip) {
-		err = dev->ops->dev_reset_chip(dev, priv->channel);
+	if (ops->dev_reset_chip) {
+		err = ops->dev_reset_chip(dev, priv->channel);
 		if (err)
 			netdev_warn(netdev, "Cannot reset card, error %d\n",
 				    err);
 	}
 
-	err = dev->ops->dev_stop_chip(priv);
+	err = ops->dev_stop_chip(priv);
 	if (err)
 		netdev_warn(netdev, "Cannot stop device, error %d\n", err);
 
@@ -499,6 +532,93 @@
 	return 0;
 }
 
+static int kvaser_usb_set_bittiming(struct net_device *netdev)
+{
+	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
+	struct kvaser_usb *dev = priv->dev;
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
+	struct can_bittiming *bt = &priv->can.bittiming;
+
+	struct kvaser_usb_busparams busparams;
+	int tseg1 = bt->prop_seg + bt->phase_seg1;
+	int tseg2 = bt->phase_seg2;
+	int sjw = bt->sjw;
+	int err = -EOPNOTSUPP;
+
+	busparams.bitrate = cpu_to_le32(bt->bitrate);
+	busparams.sjw = (u8)sjw;
+	busparams.tseg1 = (u8)tseg1;
+	busparams.tseg2 = (u8)tseg2;
+	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
+		busparams.nsamples = 3;
+	else
+		busparams.nsamples = 1;
+
+	err = ops->dev_set_bittiming(netdev, &busparams);
+	if (err)
+		return err;
+
+	err = kvaser_usb_setup_rx_urbs(priv->dev);
+	if (err)
+		return err;
+
+	err = ops->dev_get_busparams(priv);
+	if (err) {
+		/* Treat EOPNOTSUPP as success */
+		if (err == -EOPNOTSUPP)
+			err = 0;
+		return err;
+	}
+
+	if (memcmp(&busparams, &priv->busparams_nominal,
+		   sizeof(priv->busparams_nominal)) != 0)
+		err = -EINVAL;
+
+	return err;
+}
+
+static int kvaser_usb_set_data_bittiming(struct net_device *netdev)
+{
+	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
+	struct kvaser_usb *dev = priv->dev;
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
+	struct can_bittiming *dbt = &priv->can.data_bittiming;
+
+	struct kvaser_usb_busparams busparams;
+	int tseg1 = dbt->prop_seg + dbt->phase_seg1;
+	int tseg2 = dbt->phase_seg2;
+	int sjw = dbt->sjw;
+	int err;
+
+	if (!ops->dev_set_data_bittiming ||
+	    !ops->dev_get_data_busparams)
+		return -EOPNOTSUPP;
+
+	busparams.bitrate = cpu_to_le32(dbt->bitrate);
+	busparams.sjw = (u8)sjw;
+	busparams.tseg1 = (u8)tseg1;
+	busparams.tseg2 = (u8)tseg2;
+	busparams.nsamples = 1;
+
+	err = ops->dev_set_data_bittiming(netdev, &busparams);
+	if (err)
+		return err;
+
+	err = kvaser_usb_setup_rx_urbs(priv->dev);
+	if (err)
+		return err;
+
+	err = ops->dev_get_data_busparams(priv);
+	if (err)
+		return err;
+
+	if (memcmp(&busparams, &priv->busparams_data,
+		   sizeof(priv->busparams_data)) != 0)
+		err = -EINVAL;
+
+	return err;
+}
+
 static void kvaser_usb_write_bulk_callback(struct urb *urb)
 {
 	struct kvaser_usb_tx_urb_context *context = urb->context;
@@ -525,6 +645,7 @@
 {
 	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
 	struct kvaser_usb *dev = priv->dev;
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
 	struct net_device_stats *stats = &netdev->stats;
 	struct kvaser_usb_tx_urb_context *context = NULL;
 	struct urb *urb;
@@ -567,8 +688,8 @@
 		goto freeurb;
 	}
 
-	buf = dev->ops->dev_frame_to_cmd(priv, skb, &context->dlc, &cmd_len,
-					 context->echo_index);
+	buf = ops->dev_frame_to_cmd(priv, skb, &context->dlc, &cmd_len,
+				    context->echo_index);
 	if (!buf) {
 		stats->tx_dropped++;
 		dev_kfree_skb(skb);
@@ -633,6 +754,7 @@
 
 static void kvaser_usb_remove_interfaces(struct kvaser_usb *dev)
 {
+	const struct kvaser_usb_dev_ops *ops = dev->driver_info->ops;
 	int i;
 
 	for (i = 0; i < dev->nchannels; i++) {
@@ -648,19 +770,23 @@
 		if (!dev->nets[i])
 			continue;
 
+		if (ops->dev_remove_channel)
+			ops->dev_remove_channel(dev->nets[i]);
+
 		free_candev(dev->nets[i]->netdev);
 	}
 }
 
-static int kvaser_usb_init_one(struct kvaser_usb *dev,
-			       const struct usb_device_id *id, int channel)
+static int kvaser_usb_init_one(struct kvaser_usb *dev, int channel)
 {
 	struct net_device *netdev;
 	struct kvaser_usb_net_priv *priv;
+	const struct kvaser_usb_driver_info *driver_info = dev->driver_info;
+	const struct kvaser_usb_dev_ops *ops = driver_info->ops;
 	int err;
 
-	if (dev->ops->dev_reset_chip) {
-		err = dev->ops->dev_reset_chip(dev, channel);
+	if (ops->dev_reset_chip) {
+		err = ops->dev_reset_chip(dev, channel);
 		if (err)
 			return err;
 	}
@@ -677,6 +803,8 @@
 	init_usb_anchor(&priv->tx_submitted);
 	init_completion(&priv->start_comp);
 	init_completion(&priv->stop_comp);
+	init_completion(&priv->flush_comp);
+	init_completion(&priv->get_busparams_comp);
 	priv->can.ctrlmode_supported = 0;
 
 	priv->dev = dev;
@@ -689,20 +817,19 @@
 	priv->can.state = CAN_STATE_STOPPED;
 	priv->can.clock.freq = dev->cfg->clock.freq;
 	priv->can.bittiming_const = dev->cfg->bittiming_const;
-	priv->can.do_set_bittiming = dev->ops->dev_set_bittiming;
-	priv->can.do_set_mode = dev->ops->dev_set_mode;
-	if ((id->driver_info & KVASER_USB_HAS_TXRX_ERRORS) ||
+	priv->can.do_set_bittiming = kvaser_usb_set_bittiming;
+	priv->can.do_set_mode = ops->dev_set_mode;
+	if ((driver_info->quirks & KVASER_USB_QUIRK_HAS_TXRX_ERRORS) ||
 	    (priv->dev->card_data.capabilities & KVASER_USB_CAP_BERR_CAP))
-		priv->can.do_get_berr_counter = dev->ops->dev_get_berr_counter;
-	if (id->driver_info & KVASER_USB_HAS_SILENT_MODE)
+		priv->can.do_get_berr_counter = ops->dev_get_berr_counter;
+	if (driver_info->quirks & KVASER_USB_QUIRK_HAS_SILENT_MODE)
 		priv->can.ctrlmode_supported |= CAN_CTRLMODE_LISTENONLY;
 
 	priv->can.ctrlmode_supported |= dev->card_data.ctrlmode_supported;
 
 	if (priv->can.ctrlmode_supported & CAN_CTRLMODE_FD) {
 		priv->can.data_bittiming_const = dev->cfg->data_bittiming_const;
-		priv->can.do_set_data_bittiming =
-					dev->ops->dev_set_data_bittiming;
+		priv->can.do_set_data_bittiming = kvaser_usb_set_data_bittiming;
 	}
 
 	netdev->flags |= IFF_ECHO;
@@ -714,17 +841,26 @@
 
 	dev->nets[channel] = priv;
 
+	if (ops->dev_init_channel) {
+		err = ops->dev_init_channel(priv);
+		if (err)
+			goto err;
+	}
+
 	err = register_candev(netdev);
 	if (err) {
 		dev_err(&dev->intf->dev, "Failed to register CAN device\n");
-		free_candev(netdev);
-		dev->nets[channel] = NULL;
-		return err;
+		goto err;
 	}
 
 	netdev_dbg(netdev, "device registered\n");
 
 	return 0;
+
+err:
+	free_candev(netdev);
+	dev->nets[channel] = NULL;
+	return err;
 }
 
 static int kvaser_usb_probe(struct usb_interface *intf,
@@ -733,29 +869,22 @@
 	struct kvaser_usb *dev;
 	int err;
 	int i;
+	const struct kvaser_usb_driver_info *driver_info;
+	const struct kvaser_usb_dev_ops *ops;
+
+	driver_info = (const struct kvaser_usb_driver_info *)id->driver_info;
+	if (!driver_info)
+		return -ENODEV;
 
 	dev = devm_kzalloc(&intf->dev, sizeof(*dev), GFP_KERNEL);
 	if (!dev)
 		return -ENOMEM;
 
-	if (kvaser_is_leaf(id)) {
-		dev->card_data.leaf.family = KVASER_LEAF;
-		dev->ops = &kvaser_usb_leaf_dev_ops;
-	} else if (kvaser_is_usbcan(id)) {
-		dev->card_data.leaf.family = KVASER_USBCAN;
-		dev->ops = &kvaser_usb_leaf_dev_ops;
-	} else if (kvaser_is_hydra(id)) {
-		dev->ops = &kvaser_usb_hydra_dev_ops;
-	} else {
-		dev_err(&intf->dev,
-			"Product ID (%d) is not a supported Kvaser USB device\n",
-			id->idProduct);
-		return -ENODEV;
-	}
-
 	dev->intf = intf;
+	dev->driver_info = driver_info;
+	ops = driver_info->ops;
 
-	err = dev->ops->dev_setup_endpoints(dev);
+	err = ops->dev_setup_endpoints(dev);
 	if (err) {
 		dev_err(&intf->dev, "Cannot get usb endpoint(s)");
 		return err;
@@ -769,22 +898,22 @@
 
 	dev->card_data.ctrlmode_supported = 0;
 	dev->card_data.capabilities = 0;
-	err = dev->ops->dev_init_card(dev);
+	err = ops->dev_init_card(dev);
 	if (err) {
 		dev_err(&intf->dev,
 			"Failed to initialize card, error %d\n", err);
 		return err;
 	}
 
-	err = dev->ops->dev_get_software_info(dev);
+	err = ops->dev_get_software_info(dev);
 	if (err) {
 		dev_err(&intf->dev,
 			"Cannot get software info, error %d\n", err);
 		return err;
 	}
 
-	if (dev->ops->dev_get_software_details) {
-		err = dev->ops->dev_get_software_details(dev);
+	if (ops->dev_get_software_details) {
+		err = ops->dev_get_software_details(dev);
 		if (err) {
 			dev_err(&intf->dev,
 				"Cannot get software details, error %d\n", err);
@@ -802,14 +931,14 @@
 
 	dev_dbg(&intf->dev, "Max outstanding tx = %d URBs\n", dev->max_tx_urbs);
 
-	err = dev->ops->dev_get_card_info(dev);
+	err = ops->dev_get_card_info(dev);
 	if (err) {
 		dev_err(&intf->dev, "Cannot get card info, error %d\n", err);
 		return err;
 	}
 
-	if (dev->ops->dev_get_capabilities) {
-		err = dev->ops->dev_get_capabilities(dev);
+	if (ops->dev_get_capabilities) {
+		err = ops->dev_get_capabilities(dev);
 		if (err) {
 			dev_err(&intf->dev,
 				"Cannot get capabilities, error %d\n", err);
@@ -819,7 +948,7 @@
 	}
 
 	for (i = 0; i < dev->nchannels; i++) {
-		err = kvaser_usb_init_one(dev, id, i);
+		err = kvaser_usb_init_one(dev, i);
 		if (err) {
 			kvaser_usb_remove_interfaces(dev);
 			return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c
@@ -22,6 +22,7 @@
 #include <linux/spinlock.h>
 #include <linux/string.h>
 #include <linux/types.h>
+#include <linux/units.h>
 #include <linux/usb.h>
 
 #include <linux/can.h>
@@ -44,6 +45,8 @@
 
 /* Minihydra command IDs */
 #define CMD_SET_BUSPARAMS_REQ			16
+#define CMD_GET_BUSPARAMS_REQ			17
+#define CMD_GET_BUSPARAMS_RESP			18
 #define CMD_GET_CHIP_STATE_REQ			19
 #define CMD_CHIP_STATE_EVENT			20
 #define CMD_SET_DRIVERMODE_REQ			21
@@ -195,21 +198,26 @@
 #define KVASER_USB_HYDRA_BUS_MODE_CANFD_ISO	0x01
 #define KVASER_USB_HYDRA_BUS_MODE_NONISO	0x02
 struct kvaser_cmd_set_busparams {
-	__le32 bitrate;
-	u8 tseg1;
-	u8 tseg2;
-	u8 sjw;
-	u8 nsamples;
+	struct kvaser_usb_busparams busparams_nominal;
 	u8 reserved0[4];
-	__le32 bitrate_d;
-	u8 tseg1_d;
-	u8 tseg2_d;
-	u8 sjw_d;
-	u8 nsamples_d;
+	struct kvaser_usb_busparams busparams_data;
 	u8 canfd_mode;
 	u8 reserved1[7];
 } __packed;
 
+/* Busparam type */
+#define KVASER_USB_HYDRA_BUSPARAM_TYPE_CAN	0x00
+#define KVASER_USB_HYDRA_BUSPARAM_TYPE_CANFD	0x01
+struct kvaser_cmd_get_busparams_req {
+	u8 type;
+	u8 reserved[27];
+} __packed;
+
+struct kvaser_cmd_get_busparams_res {
+	struct kvaser_usb_busparams busparams;
+	u8 reserved[20];
+} __packed;
+
 /* Ctrl modes */
 #define KVASER_USB_HYDRA_CTRLMODE_NORMAL	0x01
 #define KVASER_USB_HYDRA_CTRLMODE_LISTEN	0x02
@@ -280,6 +288,8 @@
 		struct kvaser_cmd_error_event error_event;
 
 		struct kvaser_cmd_set_busparams set_busparams_req;
+		struct kvaser_cmd_get_busparams_req get_busparams_req;
+		struct kvaser_cmd_get_busparams_res get_busparams_res;
 
 		struct kvaser_cmd_chip_state_event chip_state_event;
 
@@ -295,6 +305,7 @@
 #define KVASER_USB_HYDRA_CF_FLAG_OVERRUN	BIT(1)
 #define KVASER_USB_HYDRA_CF_FLAG_REMOTE_FRAME	BIT(4)
 #define KVASER_USB_HYDRA_CF_FLAG_EXTENDED_ID	BIT(5)
+#define KVASER_USB_HYDRA_CF_FLAG_TX_ACK		BIT(6)
 /* CAN frame flags. Used in ext_rx_can and ext_tx_can */
 #define KVASER_USB_HYDRA_CF_FLAG_OSM_NACK	BIT(12)
 #define KVASER_USB_HYDRA_CF_FLAG_ABL		BIT(13)
@@ -361,6 +372,10 @@
 	} __packed;
 } __packed;
 
+struct kvaser_usb_net_hydra_priv {
+	int pending_get_busparams_type;
+};
+
 static const struct can_bittiming_const kvaser_usb_hydra_kcan_bittiming_c = {
 	.name = "kvaser_usb_kcan",
 	.tseg1_min = 1,
@@ -373,7 +388,7 @@
 	.brp_inc = 1,
 };
 
-static const struct can_bittiming_const kvaser_usb_hydra_flexc_bittiming_c = {
+const struct can_bittiming_const kvaser_usb_flexc_bittiming_const = {
 	.name = "kvaser_usb_flex",
 	.tseg1_min = 4,
 	.tseg1_max = 16,
@@ -530,6 +545,7 @@
 					    u8 cmd_no, int channel)
 {
 	struct kvaser_cmd *cmd;
+	size_t cmd_len;
 	int err;
 
 	cmd = kcalloc(1, sizeof(struct kvaser_cmd), GFP_KERNEL);
@@ -537,6 +553,7 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = cmd_no;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
 	if (channel < 0) {
 		kvaser_usb_hydra_set_cmd_dest_he
 				(cmd, KVASER_USB_HYDRA_HE_ADDRESS_ILLEGAL);
@@ -553,7 +570,7 @@
 	kvaser_usb_hydra_set_cmd_transid
 				(cmd, kvaser_usb_hydra_get_next_transid(dev));
 
-	err = kvaser_usb_send_cmd(dev, cmd, kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
 	if (err)
 		goto end;
 
@@ -569,6 +586,7 @@
 {
 	struct kvaser_cmd *cmd;
 	struct kvaser_usb *dev = priv->dev;
+	size_t cmd_len;
 	int err;
 
 	cmd = kcalloc(1, sizeof(struct kvaser_cmd), GFP_ATOMIC);
@@ -576,14 +594,14 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = cmd_no;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
 
 	kvaser_usb_hydra_set_cmd_dest_he
 		(cmd, dev->card_data.hydra.channel_to_he[priv->channel]);
 	kvaser_usb_hydra_set_cmd_transid
 				(cmd, kvaser_usb_hydra_get_next_transid(dev));
 
-	err = kvaser_usb_send_cmd_async(priv, cmd,
-					kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd_async(priv, cmd, cmd_len);
 	if (err)
 		kfree(cmd);
 
@@ -727,6 +745,7 @@
 {
 	struct kvaser_usb_dev_card_data *card_data = &dev->card_data;
 	struct kvaser_cmd *cmd;
+	size_t cmd_len;
 	u32 value = 0;
 	u32 mask = 0;
 	u16 cap_cmd_res;
@@ -738,13 +757,14 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_GET_CAPABILITIES_REQ;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
 	cmd->cap_req.cap_cmd = cpu_to_le16(cap_cmd_req);
 
 	kvaser_usb_hydra_set_cmd_dest_he(cmd, card_data->hydra.sysdbg_he);
 	kvaser_usb_hydra_set_cmd_transid
 				(cmd, kvaser_usb_hydra_get_next_transid(dev));
 
-	err = kvaser_usb_send_cmd(dev, cmd, kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
 	if (err)
 		goto end;
 
@@ -838,6 +858,39 @@
 	complete(&priv->flush_comp);
 }
 
+static void kvaser_usb_hydra_get_busparams_reply(const struct kvaser_usb *dev,
+						 const struct kvaser_cmd *cmd)
+{
+	struct kvaser_usb_net_priv *priv;
+	struct kvaser_usb_net_hydra_priv *hydra;
+
+	priv = kvaser_usb_hydra_net_priv_from_cmd(dev, cmd);
+	if (!priv)
+		return;
+
+	hydra = priv->sub_priv;
+	if (!hydra)
+		return;
+
+	switch (hydra->pending_get_busparams_type) {
+	case KVASER_USB_HYDRA_BUSPARAM_TYPE_CAN:
+		memcpy(&priv->busparams_nominal, &cmd->get_busparams_res.busparams,
+		       sizeof(priv->busparams_nominal));
+		break;
+	case KVASER_USB_HYDRA_BUSPARAM_TYPE_CANFD:
+		memcpy(&priv->busparams_data, &cmd->get_busparams_res.busparams,
+		       sizeof(priv->busparams_nominal));
+		break;
+	default:
+		dev_warn(&dev->intf->dev, "Unknown get_busparams_type %d\n",
+			 hydra->pending_get_busparams_type);
+		break;
+	}
+	hydra->pending_get_busparams_type = -1;
+
+	complete(&priv->get_busparams_comp);
+}
+
 static void
 kvaser_usb_hydra_bus_status_to_can_state(const struct kvaser_usb_net_priv *priv,
 					 u8 bus_status,
@@ -869,7 +922,6 @@
 	struct net_device *netdev = priv->netdev;
 	struct can_frame *cf;
 	struct sk_buff *skb;
-	struct net_device_stats *stats;
 	enum can_state new_state, old_state;
 
 	old_state = priv->can.state;
@@ -916,12 +968,11 @@
 	    new_state < CAN_STATE_BUS_OFF)
 		priv->can.can_stats.restarts++;
 
-	cf->data[6] = bec->txerr;
-	cf->data[7] = bec->rxerr;
+	if (new_state != CAN_STATE_BUS_OFF) {
+		cf->data[6] = bec->txerr;
+		cf->data[7] = bec->rxerr;
+	}
 
-	stats = &netdev->stats;
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 }
 
@@ -1071,11 +1122,11 @@
 	shhwtstamps->hwtstamp = hwtstamp;
 
 	cf->can_id |= CAN_ERR_BUSERROR;
-	cf->data[6] = bec.txerr;
-	cf->data[7] = bec.rxerr;
+	if (new_state != CAN_STATE_BUS_OFF) {
+		cf->data[6] = bec.txerr;
+		cf->data[7] = bec.rxerr;
+	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 
 	priv->bec.txerr = bec.txerr;
@@ -1109,8 +1160,6 @@
 	}
 
 	stats->tx_errors++;
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 }
 
@@ -1121,6 +1170,7 @@
 	struct kvaser_usb_net_priv *priv;
 	unsigned long irq_flags;
 	bool one_shot_fail = false;
+	bool is_err_frame = false;
 	u16 transid = kvaser_usb_hydra_get_cmd_transid(cmd);
 
 	priv = kvaser_usb_hydra_net_priv_from_cmd(dev, cmd);
@@ -1139,10 +1189,13 @@
 			kvaser_usb_hydra_one_shot_fail(priv, cmd_ext);
 			one_shot_fail = true;
 		}
+
+		is_err_frame = flags & KVASER_USB_HYDRA_CF_FLAG_TX_ACK &&
+			       flags & KVASER_USB_HYDRA_CF_FLAG_ERROR_FRAME;
 	}
 
 	context = &priv->tx_contexts[transid % dev->max_tx_urbs];
-	if (!one_shot_fail) {
+	if (!one_shot_fail && !is_err_frame) {
 		struct net_device_stats *stats = &priv->netdev->stats;
 
 		stats->tx_packets++;
@@ -1316,6 +1369,10 @@
 		kvaser_usb_hydra_state_event(dev, cmd);
 		break;
 
+	case CMD_GET_BUSPARAMS_RESP:
+		kvaser_usb_hydra_get_busparams_reply(dev, cmd);
+		break;
+
 	case CMD_ERROR_EVENT:
 		kvaser_usb_hydra_error_event(dev, cmd);
 		break;
@@ -1516,15 +1573,61 @@
 	return err;
 }
 
-static int kvaser_usb_hydra_set_bittiming(struct net_device *netdev)
+static int kvaser_usb_hydra_get_busparams(struct kvaser_usb_net_priv *priv,
+					  int busparams_type)
+{
+	struct kvaser_usb *dev = priv->dev;
+	struct kvaser_usb_net_hydra_priv *hydra = priv->sub_priv;
+	struct kvaser_cmd *cmd;
+	size_t cmd_len;
+	int err;
+
+	if (!hydra)
+		return -EINVAL;
+
+	cmd = kcalloc(1, sizeof(struct kvaser_cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
+
+	cmd->header.cmd_no = CMD_GET_BUSPARAMS_REQ;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
+	kvaser_usb_hydra_set_cmd_dest_he
+		(cmd, dev->card_data.hydra.channel_to_he[priv->channel]);
+	kvaser_usb_hydra_set_cmd_transid
+				(cmd, kvaser_usb_hydra_get_next_transid(dev));
+	cmd->get_busparams_req.type = busparams_type;
+	hydra->pending_get_busparams_type = busparams_type;
+
+	reinit_completion(&priv->get_busparams_comp);
+
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
+	if (err)
+		return err;
+
+	if (!wait_for_completion_timeout(&priv->get_busparams_comp,
+					 msecs_to_jiffies(KVASER_USB_TIMEOUT)))
+		return -ETIMEDOUT;
+
+	return err;
+}
+
+static int kvaser_usb_hydra_get_nominal_busparams(struct kvaser_usb_net_priv *priv)
+{
+	return kvaser_usb_hydra_get_busparams(priv, KVASER_USB_HYDRA_BUSPARAM_TYPE_CAN);
+}
+
+static int kvaser_usb_hydra_get_data_busparams(struct kvaser_usb_net_priv *priv)
+{
+	return kvaser_usb_hydra_get_busparams(priv, KVASER_USB_HYDRA_BUSPARAM_TYPE_CANFD);
+}
+
+static int kvaser_usb_hydra_set_bittiming(const struct net_device *netdev,
+					  const struct kvaser_usb_busparams *busparams)
 {
 	struct kvaser_cmd *cmd;
 	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
-	struct can_bittiming *bt = &priv->can.bittiming;
 	struct kvaser_usb *dev = priv->dev;
-	int tseg1 = bt->prop_seg + bt->phase_seg1;
-	int tseg2 = bt->phase_seg2;
-	int sjw = bt->sjw;
+	size_t cmd_len;
 	int err;
 
 	cmd = kcalloc(1, sizeof(struct kvaser_cmd), GFP_KERNEL);
@@ -1532,33 +1635,29 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_SET_BUSPARAMS_REQ;
-	cmd->set_busparams_req.bitrate = cpu_to_le32(bt->bitrate);
-	cmd->set_busparams_req.sjw = (u8)sjw;
-	cmd->set_busparams_req.tseg1 = (u8)tseg1;
-	cmd->set_busparams_req.tseg2 = (u8)tseg2;
-	cmd->set_busparams_req.nsamples = 1;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
+	memcpy(&cmd->set_busparams_req.busparams_nominal, busparams,
+	       sizeof(cmd->set_busparams_req.busparams_nominal));
 
 	kvaser_usb_hydra_set_cmd_dest_he
 		(cmd, dev->card_data.hydra.channel_to_he[priv->channel]);
 	kvaser_usb_hydra_set_cmd_transid
 				(cmd, kvaser_usb_hydra_get_next_transid(dev));
 
-	err = kvaser_usb_send_cmd(dev, cmd, kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
 
 	kfree(cmd);
 
 	return err;
 }
 
-static int kvaser_usb_hydra_set_data_bittiming(struct net_device *netdev)
+static int kvaser_usb_hydra_set_data_bittiming(const struct net_device *netdev,
+					       const struct kvaser_usb_busparams *busparams)
 {
 	struct kvaser_cmd *cmd;
 	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
-	struct can_bittiming *dbt = &priv->can.data_bittiming;
 	struct kvaser_usb *dev = priv->dev;
-	int tseg1 = dbt->prop_seg + dbt->phase_seg1;
-	int tseg2 = dbt->phase_seg2;
-	int sjw = dbt->sjw;
+	size_t cmd_len;
 	int err;
 
 	cmd = kcalloc(1, sizeof(struct kvaser_cmd), GFP_KERNEL);
@@ -1566,11 +1665,9 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_SET_BUSPARAMS_FD_REQ;
-	cmd->set_busparams_req.bitrate_d = cpu_to_le32(dbt->bitrate);
-	cmd->set_busparams_req.sjw_d = (u8)sjw;
-	cmd->set_busparams_req.tseg1_d = (u8)tseg1;
-	cmd->set_busparams_req.tseg2_d = (u8)tseg2;
-	cmd->set_busparams_req.nsamples_d = 1;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
+	memcpy(&cmd->set_busparams_req.busparams_data, busparams,
+	       sizeof(cmd->set_busparams_req.busparams_data));
 
 	if (priv->can.ctrlmode & CAN_CTRLMODE_FD) {
 		if (priv->can.ctrlmode & CAN_CTRLMODE_FD_NON_ISO)
@@ -1586,7 +1683,7 @@
 	kvaser_usb_hydra_set_cmd_transid
 				(cmd, kvaser_usb_hydra_get_next_transid(dev));
 
-	err = kvaser_usb_send_cmd(dev, cmd, kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
 
 	kfree(cmd);
 
@@ -1677,6 +1774,19 @@
 	return 0;
 }
 
+static int kvaser_usb_hydra_init_channel(struct kvaser_usb_net_priv *priv)
+{
+	struct kvaser_usb_net_hydra_priv *hydra;
+
+	hydra = devm_kzalloc(&priv->dev->intf->dev, sizeof(*hydra), GFP_KERNEL);
+	if (!hydra)
+		return -ENOMEM;
+
+	priv->sub_priv = hydra;
+
+	return 0;
+}
+
 static int kvaser_usb_hydra_get_software_info(struct kvaser_usb *dev)
 {
 	struct kvaser_cmd cmd;
@@ -1701,6 +1811,7 @@
 static int kvaser_usb_hydra_get_software_details(struct kvaser_usb *dev)
 {
 	struct kvaser_cmd *cmd;
+	size_t cmd_len;
 	int err;
 	u32 flags;
 	struct kvaser_usb_dev_card_data *card_data = &dev->card_data;
@@ -1710,6 +1821,7 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_GET_SOFTWARE_DETAILS_REQ;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
 	cmd->sw_detail_req.use_ext_cmd = 1;
 	kvaser_usb_hydra_set_cmd_dest_he
 				(cmd, KVASER_USB_HYDRA_HE_ADDRESS_ILLEGAL);
@@ -1717,7 +1829,7 @@
 	kvaser_usb_hydra_set_cmd_transid
 				(cmd, kvaser_usb_hydra_get_next_transid(dev));
 
-	err = kvaser_usb_send_cmd(dev, cmd, kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
 	if (err)
 		goto end;
 
@@ -1835,6 +1947,7 @@
 {
 	struct kvaser_usb *dev = priv->dev;
 	struct kvaser_cmd *cmd;
+	size_t cmd_len;
 	int err;
 
 	if ((priv->can.ctrlmode &
@@ -1850,6 +1963,7 @@
 		return -ENOMEM;
 
 	cmd->header.cmd_no = CMD_SET_DRIVERMODE_REQ;
+	cmd_len = kvaser_usb_hydra_cmd_size(cmd);
 	kvaser_usb_hydra_set_cmd_dest_he
 		(cmd, dev->card_data.hydra.channel_to_he[priv->channel]);
 	kvaser_usb_hydra_set_cmd_transid
@@ -1859,7 +1973,7 @@
 	else
 		cmd->set_ctrlmode.mode = KVASER_USB_HYDRA_CTRLMODE_NORMAL;
 
-	err = kvaser_usb_send_cmd(dev, cmd, kvaser_usb_hydra_cmd_size(cmd));
+	err = kvaser_usb_send_cmd(dev, cmd, cmd_len);
 	kfree(cmd);
 
 	return err;
@@ -1869,7 +1983,7 @@
 {
 	int err;
 
-	init_completion(&priv->start_comp);
+	reinit_completion(&priv->start_comp);
 
 	err = kvaser_usb_hydra_send_simple_cmd(priv->dev, CMD_START_CHIP_REQ,
 					       priv->channel);
@@ -1887,7 +2001,7 @@
 {
 	int err;
 
-	init_completion(&priv->stop_comp);
+	reinit_completion(&priv->stop_comp);
 
 	/* Make sure we do not report invalid BUS_OFF from CMD_CHIP_STATE_EVENT
 	 * see comment in kvaser_usb_hydra_update_state()
@@ -1910,7 +2024,7 @@
 {
 	int err;
 
-	init_completion(&priv->flush_comp);
+	reinit_completion(&priv->flush_comp);
 
 	err = kvaser_usb_hydra_send_simple_cmd(priv->dev, CMD_FLUSH_QUEUE,
 					       priv->channel);
@@ -2021,10 +2135,13 @@
 const struct kvaser_usb_dev_ops kvaser_usb_hydra_dev_ops = {
 	.dev_set_mode = kvaser_usb_hydra_set_mode,
 	.dev_set_bittiming = kvaser_usb_hydra_set_bittiming,
+	.dev_get_busparams = kvaser_usb_hydra_get_nominal_busparams,
 	.dev_set_data_bittiming = kvaser_usb_hydra_set_data_bittiming,
+	.dev_get_data_busparams = kvaser_usb_hydra_get_data_busparams,
 	.dev_get_berr_counter = kvaser_usb_hydra_get_berr_counter,
 	.dev_setup_endpoints = kvaser_usb_hydra_setup_endpoints,
 	.dev_init_card = kvaser_usb_hydra_init_card,
+	.dev_init_channel = kvaser_usb_hydra_init_channel,
 	.dev_get_software_info = kvaser_usb_hydra_get_software_info,
 	.dev_get_software_details = kvaser_usb_hydra_get_software_details,
 	.dev_get_card_info = kvaser_usb_hydra_get_card_info,
@@ -2040,7 +2157,7 @@
 
 static const struct kvaser_usb_dev_cfg kvaser_usb_hydra_dev_cfg_kcan = {
 	.clock = {
-		.freq = 80000000,
+		.freq = 80 * MEGA /* Hz */,
 	},
 	.timestamp_freq = 80,
 	.bittiming_const = &kvaser_usb_hydra_kcan_bittiming_c,
@@ -2049,15 +2166,15 @@
 
 static const struct kvaser_usb_dev_cfg kvaser_usb_hydra_dev_cfg_flexc = {
 	.clock = {
-		.freq = 24000000,
+		.freq = 24 * MEGA /* Hz */,
 	},
 	.timestamp_freq = 1,
-	.bittiming_const = &kvaser_usb_hydra_flexc_bittiming_c,
+	.bittiming_const = &kvaser_usb_flexc_bittiming_const,
 };
 
 static const struct kvaser_usb_dev_cfg kvaser_usb_hydra_dev_cfg_rt = {
 	.clock = {
-		.freq = 80000000,
+		.freq = 80 * MEGA /* Hz */,
 	},
 	.timestamp_freq = 24,
 	.bittiming_const = &kvaser_usb_hydra_rt_bittiming_c,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c
@@ -19,7 +19,9 @@
 #include <linux/spinlock.h>
 #include <linux/string.h>
 #include <linux/types.h>
+#include <linux/units.h>
 #include <linux/usb.h>
+#include <linux/workqueue.h>
 
 #include <linux/can.h>
 #include <linux/can/dev.h>
@@ -28,10 +30,6 @@
 
 #include "kvaser_usb.h"
 
-/* Forward declaration */
-static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_dev_cfg;
-
-#define CAN_USB_CLOCK			8000000
 #define MAX_USBCAN_NET_DEVICES		2
 
 /* Command header size */
@@ -59,6 +57,9 @@
 #define CMD_RX_EXT_MESSAGE		14
 #define CMD_TX_EXT_MESSAGE		15
 #define CMD_SET_BUS_PARAMS		16
+#define CMD_GET_BUS_PARAMS		17
+#define CMD_GET_BUS_PARAMS_REPLY	18
+#define CMD_GET_CHIP_STATE		19
 #define CMD_CHIP_STATE_EVENT		20
 #define CMD_SET_CTRL_MODE		21
 #define CMD_RESET_CHIP			24
@@ -73,13 +74,24 @@
 #define CMD_GET_CARD_INFO_REPLY		35
 #define CMD_GET_SOFTWARE_INFO		38
 #define CMD_GET_SOFTWARE_INFO_REPLY	39
+#define CMD_ERROR_EVENT			45
 #define CMD_FLUSH_QUEUE			48
 #define CMD_TX_ACKNOWLEDGE		50
 #define CMD_CAN_ERROR_EVENT		51
 #define CMD_FLUSH_QUEUE_REPLY		68
+#define CMD_GET_CAPABILITIES_REQ	95
+#define CMD_GET_CAPABILITIES_RESP	96
 
 #define CMD_LEAF_LOG_MESSAGE		106
 
+/* Leaf frequency options */
+#define KVASER_USB_LEAF_SWOPTION_FREQ_MASK 0x60
+#define KVASER_USB_LEAF_SWOPTION_FREQ_16_MHZ_CLK 0
+#define KVASER_USB_LEAF_SWOPTION_FREQ_32_MHZ_CLK BIT(5)
+#define KVASER_USB_LEAF_SWOPTION_FREQ_24_MHZ_CLK BIT(6)
+
+#define KVASER_USB_LEAF_SWOPTION_EXT_CAP BIT(12)
+
 /* error factors */
 #define M16C_EF_ACKE			BIT(0)
 #define M16C_EF_CRCE			BIT(1)
@@ -98,16 +110,6 @@
 #define USBCAN_ERROR_STATE_RX_ERROR	BIT(1)
 #define USBCAN_ERROR_STATE_BUSERROR	BIT(2)
 
-/* bittiming parameters */
-#define KVASER_USB_TSEG1_MIN		1
-#define KVASER_USB_TSEG1_MAX		16
-#define KVASER_USB_TSEG2_MIN		1
-#define KVASER_USB_TSEG2_MAX		8
-#define KVASER_USB_SJW_MAX		4
-#define KVASER_USB_BRP_MIN		1
-#define KVASER_USB_BRP_MAX		64
-#define KVASER_USB_BRP_INC		1
-
 /* ctrl modes */
 #define KVASER_CTRL_MODE_NORMAL		1
 #define KVASER_CTRL_MODE_SILENT		2
@@ -164,11 +166,7 @@
 struct kvaser_cmd_busparams {
 	u8 tid;
 	u8 channel;
-	__le32 bitrate;
-	u8 tseg1;
-	u8 tseg2;
-	u8 sjw;
-	u8 no_samp;
+	struct kvaser_usb_busparams busparams;
 } __packed;
 
 struct kvaser_cmd_tx_can {
@@ -237,7 +235,7 @@
 	u8 tid;
 } __packed;
 
-struct leaf_cmd_error_event {
+struct leaf_cmd_can_error_event {
 	u8 tid;
 	u8 flags;
 	__le16 time[3];
@@ -249,7 +247,7 @@
 	u8 error_factor;
 } __packed;
 
-struct usbcan_cmd_error_event {
+struct usbcan_cmd_can_error_event {
 	u8 tid;
 	u8 padding;
 	u8 tx_errors_count_ch0;
@@ -261,6 +259,28 @@
 	__le16 time;
 } __packed;
 
+/* CMD_ERROR_EVENT error codes */
+#define KVASER_USB_LEAF_ERROR_EVENT_TX_QUEUE_FULL 0x8
+#define KVASER_USB_LEAF_ERROR_EVENT_PARAM 0x9
+
+struct leaf_cmd_error_event {
+	u8 tid;
+	u8 error_code;
+	__le16 timestamp[3];
+	__le16 padding;
+	__le16 info1;
+	__le16 info2;
+} __packed;
+
+struct usbcan_cmd_error_event {
+	u8 tid;
+	u8 error_code;
+	__le16 info1;
+	__le16 info2;
+	__le16 timestamp;
+	__le16 padding;
+} __packed;
+
 struct kvaser_cmd_ctrl_mode {
 	u8 tid;
 	u8 channel;
@@ -285,6 +305,28 @@
 	u8 data[8];
 } __packed;
 
+/* Sub commands for cap_req and cap_res */
+#define KVASER_USB_LEAF_CAP_CMD_LISTEN_MODE 0x02
+#define KVASER_USB_LEAF_CAP_CMD_ERR_REPORT 0x05
+struct kvaser_cmd_cap_req {
+	__le16 padding0;
+	__le16 cap_cmd;
+	__le16 padding1;
+	__le16 channel;
+} __packed;
+
+/* Status codes for cap_res */
+#define KVASER_USB_LEAF_CAP_STAT_OK 0x00
+#define KVASER_USB_LEAF_CAP_STAT_NOT_IMPL 0x01
+#define KVASER_USB_LEAF_CAP_STAT_UNAVAIL 0x02
+struct kvaser_cmd_cap_res {
+	__le16 padding;
+	__le16 cap_cmd;
+	__le16 status;
+	__le32 mask;
+	__le32 value;
+} __packed;
+
 struct kvaser_cmd {
 	u8 len;
 	u8 id;
@@ -300,14 +342,18 @@
 			struct leaf_cmd_softinfo softinfo;
 			struct leaf_cmd_rx_can rx_can;
 			struct leaf_cmd_chip_state_event chip_state_event;
-			struct leaf_cmd_error_event error_event;
+			struct leaf_cmd_can_error_event can_error_event;
 			struct leaf_cmd_log_message log_message;
+			struct leaf_cmd_error_event error_event;
+			struct kvaser_cmd_cap_req cap_req;
+			struct kvaser_cmd_cap_res cap_res;
 		} __packed leaf;
 
 		union {
 			struct usbcan_cmd_softinfo softinfo;
 			struct usbcan_cmd_rx_can rx_can;
 			struct usbcan_cmd_chip_state_event chip_state_event;
+			struct usbcan_cmd_can_error_event can_error_event;
 			struct usbcan_cmd_error_event error_event;
 		} __packed usbcan;
 
@@ -317,6 +363,42 @@
 	} u;
 } __packed;
 
+#define CMD_SIZE_ANY 0xff
+#define kvaser_fsize(field) sizeof_field(struct kvaser_cmd, field)
+
+static const u8 kvaser_usb_leaf_cmd_sizes_leaf[] = {
+	[CMD_START_CHIP_REPLY]		= kvaser_fsize(u.simple),
+	[CMD_STOP_CHIP_REPLY]		= kvaser_fsize(u.simple),
+	[CMD_GET_CARD_INFO_REPLY]	= kvaser_fsize(u.cardinfo),
+	[CMD_TX_ACKNOWLEDGE]		= kvaser_fsize(u.tx_acknowledge_header),
+	[CMD_GET_SOFTWARE_INFO_REPLY]	= kvaser_fsize(u.leaf.softinfo),
+	[CMD_RX_STD_MESSAGE]		= kvaser_fsize(u.leaf.rx_can),
+	[CMD_RX_EXT_MESSAGE]		= kvaser_fsize(u.leaf.rx_can),
+	[CMD_LEAF_LOG_MESSAGE]		= kvaser_fsize(u.leaf.log_message),
+	[CMD_CHIP_STATE_EVENT]		= kvaser_fsize(u.leaf.chip_state_event),
+	[CMD_CAN_ERROR_EVENT]		= kvaser_fsize(u.leaf.can_error_event),
+	[CMD_GET_CAPABILITIES_RESP]	= kvaser_fsize(u.leaf.cap_res),
+	[CMD_GET_BUS_PARAMS_REPLY]	= kvaser_fsize(u.busparams),
+	[CMD_ERROR_EVENT]		= kvaser_fsize(u.leaf.error_event),
+	/* ignored events: */
+	[CMD_FLUSH_QUEUE_REPLY]		= CMD_SIZE_ANY,
+};
+
+static const u8 kvaser_usb_leaf_cmd_sizes_usbcan[] = {
+	[CMD_START_CHIP_REPLY]		= kvaser_fsize(u.simple),
+	[CMD_STOP_CHIP_REPLY]		= kvaser_fsize(u.simple),
+	[CMD_GET_CARD_INFO_REPLY]	= kvaser_fsize(u.cardinfo),
+	[CMD_TX_ACKNOWLEDGE]		= kvaser_fsize(u.tx_acknowledge_header),
+	[CMD_GET_SOFTWARE_INFO_REPLY]	= kvaser_fsize(u.usbcan.softinfo),
+	[CMD_RX_STD_MESSAGE]		= kvaser_fsize(u.usbcan.rx_can),
+	[CMD_RX_EXT_MESSAGE]		= kvaser_fsize(u.usbcan.rx_can),
+	[CMD_CHIP_STATE_EVENT]		= kvaser_fsize(u.usbcan.chip_state_event),
+	[CMD_CAN_ERROR_EVENT]		= kvaser_fsize(u.usbcan.can_error_event),
+	[CMD_ERROR_EVENT]		= kvaser_fsize(u.usbcan.error_event),
+	/* ignored events: */
+	[CMD_USBCAN_CLOCK_OVERFLOW_EVENT] = CMD_SIZE_ANY,
+};
+
 /* Summary of a kvaser error event, for a unified Leaf/Usbcan error
  * handling. Some discrepancies between the two families exist:
  *
@@ -340,6 +422,113 @@
 	};
 };
 
+struct kvaser_usb_net_leaf_priv {
+	struct kvaser_usb_net_priv *net;
+
+	struct delayed_work chip_state_req_work;
+};
+
+static const struct can_bittiming_const kvaser_usb_leaf_m16c_bittiming_const = {
+	.name = "kvaser_usb_ucii",
+	.tseg1_min = 4,
+	.tseg1_max = 16,
+	.tseg2_min = 2,
+	.tseg2_max = 8,
+	.sjw_max = 4,
+	.brp_min = 1,
+	.brp_max = 16,
+	.brp_inc = 1,
+};
+
+static const struct can_bittiming_const kvaser_usb_leaf_m32c_bittiming_const = {
+	.name = "kvaser_usb_leaf",
+	.tseg1_min = 3,
+	.tseg1_max = 16,
+	.tseg2_min = 2,
+	.tseg2_max = 8,
+	.sjw_max = 4,
+	.brp_min = 2,
+	.brp_max = 128,
+	.brp_inc = 2,
+};
+
+static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_usbcan_dev_cfg = {
+	.clock = {
+		.freq = 8 * MEGA /* Hz */,
+	},
+	.timestamp_freq = 1,
+	.bittiming_const = &kvaser_usb_leaf_m16c_bittiming_const,
+};
+
+static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_m32c_dev_cfg = {
+	.clock = {
+		.freq = 16 * MEGA /* Hz */,
+	},
+	.timestamp_freq = 1,
+	.bittiming_const = &kvaser_usb_leaf_m32c_bittiming_const,
+};
+
+static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_imx_dev_cfg_16mhz = {
+	.clock = {
+		.freq = 16000000,
+	},
+	.timestamp_freq = 1,
+	.bittiming_const = &kvaser_usb_flexc_bittiming_const,
+};
+
+static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_imx_dev_cfg_24mhz = {
+	.clock = {
+		.freq = 24 * MEGA /* Hz */,
+	},
+	.timestamp_freq = 1,
+	.bittiming_const = &kvaser_usb_flexc_bittiming_const,
+};
+
+static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_imx_dev_cfg_32mhz = {
+	.clock = {
+		.freq = 32 * MEGA /* Hz */,
+	},
+	.timestamp_freq = 1,
+	.bittiming_const = &kvaser_usb_flexc_bittiming_const,
+};
+
+static int kvaser_usb_leaf_verify_size(const struct kvaser_usb *dev,
+				       const struct kvaser_cmd *cmd)
+{
+	/* buffer size >= cmd->len ensured by caller */
+	u8 min_size = 0;
+
+	switch (dev->driver_info->family) {
+	case KVASER_LEAF:
+		if (cmd->id < ARRAY_SIZE(kvaser_usb_leaf_cmd_sizes_leaf))
+			min_size = kvaser_usb_leaf_cmd_sizes_leaf[cmd->id];
+		break;
+	case KVASER_USBCAN:
+		if (cmd->id < ARRAY_SIZE(kvaser_usb_leaf_cmd_sizes_usbcan))
+			min_size = kvaser_usb_leaf_cmd_sizes_usbcan[cmd->id];
+		break;
+	}
+
+	if (min_size == CMD_SIZE_ANY)
+		return 0;
+
+	if (min_size) {
+		min_size += CMD_HEADER_LEN;
+		if (cmd->len >= min_size)
+			return 0;
+
+		dev_err_ratelimited(&dev->intf->dev,
+				    "Received command %u too short (size %u, needed %u)",
+				    cmd->id, cmd->len, min_size);
+		return -EIO;
+	}
+
+	dev_warn_ratelimited(&dev->intf->dev,
+			     "Unhandled command (%d, size %d)\n",
+			     cmd->id, cmd->len);
+	return -EINVAL;
+}
+
 static void *
 kvaser_usb_leaf_frame_to_cmd(const struct kvaser_usb_net_priv *priv,
 			     const struct sk_buff *skb, int *frame_len,
@@ -359,7 +548,7 @@
 				      sizeof(struct kvaser_cmd_tx_can);
 		cmd->u.tx_can.channel = priv->channel;
 
-		switch (dev->card_data.leaf.family) {
+		switch (dev->driver_info->family) {
 		case KVASER_LEAF:
 			cmd_tx_can_flags = &cmd->u.tx_can.leaf.flags;
 			break;
@@ -447,6 +636,9 @@
 end:
 	kfree(buf);
 
+	if (err == 0)
+		err = kvaser_usb_leaf_verify_size(dev, cmd);
+
 	return err;
 }
 
@@ -471,6 +663,37 @@
 	return rc;
 }
 
+static void kvaser_usb_leaf_get_software_info_leaf(struct kvaser_usb *dev,
+						   const struct leaf_cmd_softinfo *softinfo)
+{
+	u32 sw_options = le32_to_cpu(softinfo->sw_options);
+
+	dev->fw_version = le32_to_cpu(softinfo->fw_version);
+	dev->max_tx_urbs = le16_to_cpu(softinfo->max_outstanding_tx);
+
+	if (sw_options & KVASER_USB_LEAF_SWOPTION_EXT_CAP)
+		dev->card_data.capabilities |= KVASER_USB_CAP_EXT_CAP;
+
+	if (dev->driver_info->quirks & KVASER_USB_QUIRK_IGNORE_CLK_FREQ) {
+		/* Firmware expects bittiming parameters calculated for 16MHz
+		 * clock, regardless of the actual clock
+		 */
+		dev->cfg = &kvaser_usb_leaf_m32c_dev_cfg;
+	} else {
+		switch (sw_options & KVASER_USB_LEAF_SWOPTION_FREQ_MASK) {
+		case KVASER_USB_LEAF_SWOPTION_FREQ_16_MHZ_CLK:
+			dev->cfg = &kvaser_usb_leaf_imx_dev_cfg_16mhz;
+			break;
+		case KVASER_USB_LEAF_SWOPTION_FREQ_24_MHZ_CLK:
+			dev->cfg = &kvaser_usb_leaf_imx_dev_cfg_24mhz;
+			break;
+		case KVASER_USB_LEAF_SWOPTION_FREQ_32_MHZ_CLK:
+			dev->cfg = &kvaser_usb_leaf_imx_dev_cfg_32mhz;
+			break;
+		}
+	}
+}
+
 static int kvaser_usb_leaf_get_software_info_inner(struct kvaser_usb *dev)
 {
 	struct kvaser_cmd cmd;
@@ -484,16 +707,15 @@
 	if (err)
 		return err;
 
-	switch (dev->card_data.leaf.family) {
+	switch (dev->driver_info->family) {
 	case KVASER_LEAF:
-		dev->fw_version = le32_to_cpu(cmd.u.leaf.softinfo.fw_version);
-		dev->max_tx_urbs =
-			le16_to_cpu(cmd.u.leaf.softinfo.max_outstanding_tx);
+		kvaser_usb_leaf_get_software_info_leaf(dev, &cmd.u.leaf.softinfo);
 		break;
 	case KVASER_USBCAN:
 		dev->fw_version = le32_to_cpu(cmd.u.usbcan.softinfo.fw_version);
 		dev->max_tx_urbs =
 			le16_to_cpu(cmd.u.usbcan.softinfo.max_outstanding_tx);
+		dev->cfg = &kvaser_usb_leaf_usbcan_dev_cfg;
 		break;
 	}
 
@@ -532,13 +754,123 @@
 
 	dev->nchannels = cmd.u.cardinfo.nchannels;
 	if (dev->nchannels > KVASER_USB_MAX_NET_DEVICES ||
-	    (dev->card_data.leaf.family == KVASER_USBCAN &&
+	    (dev->driver_info->family == KVASER_USBCAN &&
 	     dev->nchannels > MAX_USBCAN_NET_DEVICES))
 		return -EINVAL;
 
 	return 0;
 }
 
+static int kvaser_usb_leaf_get_single_capability(struct kvaser_usb *dev,
+						 u16 cap_cmd_req, u16 *status)
+{
+	struct kvaser_usb_dev_card_data *card_data = &dev->card_data;
+	struct kvaser_cmd *cmd;
+	u32 value = 0;
+	u32 mask = 0;
+	u16 cap_cmd_res;
+	int err;
+	int i;
+
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
+
+	cmd->id = CMD_GET_CAPABILITIES_REQ;
+	cmd->u.leaf.cap_req.cap_cmd = cpu_to_le16(cap_cmd_req);
+	cmd->len = CMD_HEADER_LEN + sizeof(struct kvaser_cmd_cap_req);
+
+	err = kvaser_usb_send_cmd(dev, cmd, cmd->len);
+	if (err)
+		goto end;
+
+	err = kvaser_usb_leaf_wait_cmd(dev, CMD_GET_CAPABILITIES_RESP, cmd);
+	if (err)
+		goto end;
+
+	*status = le16_to_cpu(cmd->u.leaf.cap_res.status);
+
+	if (*status != KVASER_USB_LEAF_CAP_STAT_OK)
+		goto end;
+
+	cap_cmd_res = le16_to_cpu(cmd->u.leaf.cap_res.cap_cmd);
+	switch (cap_cmd_res) {
+	case KVASER_USB_LEAF_CAP_CMD_LISTEN_MODE:
+	case KVASER_USB_LEAF_CAP_CMD_ERR_REPORT:
+		value = le32_to_cpu(cmd->u.leaf.cap_res.value);
+		mask = le32_to_cpu(cmd->u.leaf.cap_res.mask);
+		break;
+	default:
+		dev_warn(&dev->intf->dev, "Unknown capability command %u\n",
+			 cap_cmd_res);
+		break;
+	}
+
+	for (i = 0; i < dev->nchannels; i++) {
+		if (BIT(i) & (value & mask)) {
+			switch (cap_cmd_res) {
+			case KVASER_USB_LEAF_CAP_CMD_LISTEN_MODE:
+				card_data->ctrlmode_supported |=
+						CAN_CTRLMODE_LISTENONLY;
+				break;
+			case KVASER_USB_LEAF_CAP_CMD_ERR_REPORT:
+				card_data->capabilities |=
+						KVASER_USB_CAP_BERR_CAP;
+				break;
+			}
+		}
+	}
+
+end:
+	kfree(cmd);
+
+	return err;
+}
+
+static int kvaser_usb_leaf_get_capabilities_leaf(struct kvaser_usb *dev)
+{
+	int err;
+	u16 status;
+
+	if (!(dev->card_data.capabilities & KVASER_USB_CAP_EXT_CAP)) {
+		dev_info(&dev->intf->dev,
+			 "No extended capability support. Upgrade device firmware.\n");
+		return 0;
+	}
+
+	err = kvaser_usb_leaf_get_single_capability(dev,
+						    KVASER_USB_LEAF_CAP_CMD_LISTEN_MODE,
+						    &status);
+	if (err)
+		return err;
+	if (status)
+		dev_info(&dev->intf->dev,
+			 "KVASER_USB_LEAF_CAP_CMD_LISTEN_MODE failed %u\n",
+			 status);
+
+	err = kvaser_usb_leaf_get_single_capability(dev,
+						    KVASER_USB_LEAF_CAP_CMD_ERR_REPORT,
+						    &status);
+	if (err)
+		return err;
+	if (status)
+		dev_info(&dev->intf->dev,
+			 "KVASER_USB_LEAF_CAP_CMD_ERR_REPORT failed %u\n",
+			 status);
+
+	return 0;
+}
+
+static int kvaser_usb_leaf_get_capabilities(struct kvaser_usb *dev)
+{
+	int err = 0;
+
+	if (dev->driver_info->family == KVASER_LEAF)
+		err = kvaser_usb_leaf_get_capabilities_leaf(dev);
+
+	return err;
+}
+
 static void kvaser_usb_leaf_tx_acknowledge(const struct kvaser_usb *dev,
 					   const struct kvaser_cmd *cmd)
 {
@@ -567,7 +899,7 @@
 	context = &priv->tx_contexts[tid % dev->max_tx_urbs];
 
 	/* Sometimes the state change doesn't come after a bus-off event */
-	if (priv->can.restart_ms && priv->can.state >= CAN_STATE_BUS_OFF) {
+	if (priv->can.restart_ms && priv->can.state == CAN_STATE_BUS_OFF) {
 		struct sk_buff *skb;
 		struct can_frame *cf;
 
@@ -575,8 +907,6 @@
 		if (skb) {
 			cf->can_id |= CAN_ERR_RESTARTED;
 
-			stats->rx_packets++;
-			stats->rx_bytes += cf->len;
 			netif_rx(skb);
 		} else {
 			netdev_err(priv->netdev,
@@ -623,6 +953,16 @@
 	return err;
 }
 
+static void kvaser_usb_leaf_chip_state_req_work(struct work_struct *work)
+{
+	struct kvaser_usb_net_leaf_priv *leaf =
+		container_of(work, struct kvaser_usb_net_leaf_priv,
+			     chip_state_req_work.work);
+	struct kvaser_usb_net_priv *priv = leaf->net;
+
+	kvaser_usb_leaf_simple_cmd_async(priv, CMD_GET_CHIP_STATE);
+}
+
 static void
 kvaser_usb_leaf_rx_error_update_can_state(struct kvaser_usb_net_priv *priv,
 					const struct kvaser_usb_err_summary *es,
@@ -641,20 +981,16 @@
 		new_state = CAN_STATE_BUS_OFF;
 	} else if (es->status & M16C_STATE_BUS_PASSIVE) {
 		new_state = CAN_STATE_ERROR_PASSIVE;
-	} else if (es->status & M16C_STATE_BUS_ERROR) {
+	} else if ((es->status & M16C_STATE_BUS_ERROR) &&
+		   cur_state >= CAN_STATE_BUS_OFF) {
 		/* Guard against spurious error events after a busoff */
-		if (cur_state < CAN_STATE_BUS_OFF) {
-			if (es->txerr >= 128 || es->rxerr >= 128)
-				new_state = CAN_STATE_ERROR_PASSIVE;
-			else if (es->txerr >= 96 || es->rxerr >= 96)
-				new_state = CAN_STATE_ERROR_WARNING;
-			else if (cur_state > CAN_STATE_ERROR_ACTIVE)
-				new_state = CAN_STATE_ERROR_ACTIVE;
-		}
-	}
-
-	if (!es->status)
+	} else if (es->txerr >= 128 || es->rxerr >= 128) {
+		new_state = CAN_STATE_ERROR_PASSIVE;
+	} else if (es->txerr >= 96 || es->rxerr >= 96) {
+		new_state = CAN_STATE_ERROR_WARNING;
+	} else {
 		new_state = CAN_STATE_ERROR_ACTIVE;
+	}
 
 	if (new_state != cur_state) {
 		tx_state = (es->txerr >= es->rxerr) ? new_state : 0;
@@ -664,11 +1000,11 @@
 	}
 
 	if (priv->can.restart_ms &&
-	    cur_state >= CAN_STATE_BUS_OFF &&
+	    cur_state == CAN_STATE_BUS_OFF &&
 	    new_state < CAN_STATE_BUS_OFF)
 		priv->can.can_stats.restarts++;
 
-	switch (dev->card_data.leaf.family) {
+	switch (dev->driver_info->family) {
 	case KVASER_LEAF:
 		if (es->leaf.error_factor) {
 			priv->can.can_stats.bus_error++;
@@ -698,6 +1034,7 @@
 	struct sk_buff *skb;
 	struct net_device_stats *stats;
 	struct kvaser_usb_net_priv *priv;
+	struct kvaser_usb_net_leaf_priv *leaf;
 	enum can_state old_state, new_state;
 
 	if (es->channel >= dev->nchannels) {
@@ -707,8 +1044,13 @@
 	}
 
 	priv = dev->nets[es->channel];
+	leaf = priv->sub_priv;
 	stats = &priv->netdev->stats;
 
+	/* Ignore e.g. state change to bus-off reported just after stopping */
+	if (!netif_running(priv->netdev))
+		return;
+
 	/* Update all of the CAN interface's state and error counters before
 	 * trying any memory allocation that can actually fail with -ENOMEM.
 	 *
@@ -723,6 +1065,14 @@
 	kvaser_usb_leaf_rx_error_update_can_state(priv, es, &tmp_cf);
 	new_state = priv->can.state;
 
+	/* If there are errors, request status updates periodically as we do
+	 * not get automatic notifications of improved state.
+	 */
+	if (new_state < CAN_STATE_BUS_OFF &&
+	    (es->rxerr || es->txerr || new_state == CAN_STATE_ERROR_PASSIVE))
+		schedule_delayed_work(&leaf->chip_state_req_work,
+				      msecs_to_jiffies(500));
+
 	skb = alloc_can_err_skb(priv->netdev, &cf);
 	if (!skb) {
 		stats->rx_dropped++;
@@ -740,14 +1090,14 @@
 		}
 
 		if (priv->can.restart_ms &&
-		    old_state >= CAN_STATE_BUS_OFF &&
+		    old_state == CAN_STATE_BUS_OFF &&
 		    new_state < CAN_STATE_BUS_OFF) {
 			cf->can_id |= CAN_ERR_RESTARTED;
 			netif_carrier_on(priv->netdev);
 		}
 	}
 
-	switch (dev->card_data.leaf.family) {
+	switch (dev->driver_info->family) {
 	case KVASER_LEAF:
 		if (es->leaf.error_factor) {
 			cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT;
@@ -774,11 +1124,11 @@
 		break;
 	}
 
-	cf->data[6] = es->txerr;
-	cf->data[7] = es->rxerr;
+	if (new_state != CAN_STATE_BUS_OFF) {
+		cf->data[6] = es->txerr;
+		cf->data[7] = es->rxerr;
+	}
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 }
 
@@ -838,11 +1188,11 @@
 
 	case CMD_CAN_ERROR_EVENT:
 		es.channel = 0;
-		es.status = cmd->u.usbcan.error_event.status_ch0;
-		es.txerr = cmd->u.usbcan.error_event.tx_errors_count_ch0;
-		es.rxerr = cmd->u.usbcan.error_event.rx_errors_count_ch0;
+		es.status = cmd->u.usbcan.can_error_event.status_ch0;
+		es.txerr = cmd->u.usbcan.can_error_event.tx_errors_count_ch0;
+		es.rxerr = cmd->u.usbcan.can_error_event.rx_errors_count_ch0;
 		es.usbcan.other_ch_status =
-			cmd->u.usbcan.error_event.status_ch1;
+			cmd->u.usbcan.can_error_event.status_ch1;
 		kvaser_usb_leaf_usbcan_conditionally_rx_error(dev, &es);
 
 		/* The USBCAN firmware supports up to 2 channels.
@@ -850,13 +1200,13 @@
 		 */
 		if (dev->nchannels == MAX_USBCAN_NET_DEVICES) {
 			es.channel = 1;
-			es.status = cmd->u.usbcan.error_event.status_ch1;
+			es.status = cmd->u.usbcan.can_error_event.status_ch1;
 			es.txerr =
-				cmd->u.usbcan.error_event.tx_errors_count_ch1;
+				cmd->u.usbcan.can_error_event.tx_errors_count_ch1;
 			es.rxerr =
-				cmd->u.usbcan.error_event.rx_errors_count_ch1;
+				cmd->u.usbcan.can_error_event.rx_errors_count_ch1;
 			es.usbcan.other_ch_status =
-				cmd->u.usbcan.error_event.status_ch0;
+				cmd->u.usbcan.can_error_event.status_ch0;
 			kvaser_usb_leaf_usbcan_conditionally_rx_error(dev, &es);
 		}
 		break;
@@ -873,11 +1223,11 @@
 
 	switch (cmd->id) {
 	case CMD_CAN_ERROR_EVENT:
-		es.channel = cmd->u.leaf.error_event.channel;
-		es.status = cmd->u.leaf.error_event.status;
-		es.txerr = cmd->u.leaf.error_event.tx_errors_count;
-		es.rxerr = cmd->u.leaf.error_event.rx_errors_count;
-		es.leaf.error_factor = cmd->u.leaf.error_event.error_factor;
+		es.channel = cmd->u.leaf.can_error_event.channel;
+		es.status = cmd->u.leaf.can_error_event.status;
+		es.txerr = cmd->u.leaf.can_error_event.tx_errors_count;
+		es.rxerr = cmd->u.leaf.can_error_event.rx_errors_count;
+		es.leaf.error_factor = cmd->u.leaf.can_error_event.error_factor;
 		break;
 	case CMD_LEAF_LOG_MESSAGE:
 		es.channel = cmd->u.leaf.log_message.channel;
@@ -939,7 +1289,7 @@
 	stats = &priv->netdev->stats;
 
 	if ((cmd->u.rx_can_header.flag & MSG_FLAG_ERROR_FRAME) &&
-	    (dev->card_data.leaf.family == KVASER_LEAF &&
+	    (dev->driver_info->family == KVASER_LEAF &&
 	     cmd->id == CMD_LEAF_LOG_MESSAGE)) {
 		kvaser_usb_leaf_leaf_rx_error(dev, cmd);
 		return;
@@ -955,7 +1305,7 @@
 		return;
 	}
 
-	switch (dev->card_data.leaf.family) {
+	switch (dev->driver_info->family) {
 	case KVASER_LEAF:
 		rx_data = cmd->u.leaf.rx_can.data;
 		break;
@@ -970,7 +1320,7 @@
 		return;
 	}
 
-	if (dev->card_data.leaf.family == KVASER_LEAF && cmd->id ==
+	if (dev->driver_info->family == KVASER_LEAF && cmd->id ==
 	    CMD_LEAF_LOG_MESSAGE) {
 		cf->can_id = le32_to_cpu(cmd->u.leaf.log_message.id);
 		if (cf->can_id & KVASER_EXTENDED_FRAME)
@@ -1009,6 +1359,74 @@
 	netif_rx(skb);
 }
 
+static void kvaser_usb_leaf_error_event_parameter(const struct kvaser_usb *dev,
+						  const struct kvaser_cmd *cmd)
+{
+	u16 info1 = 0;
+
+	switch (dev->driver_info->family) {
+	case KVASER_LEAF:
+		info1 = le16_to_cpu(cmd->u.leaf.error_event.info1);
+		break;
+	case KVASER_USBCAN:
+		info1 = le16_to_cpu(cmd->u.usbcan.error_event.info1);
+		break;
+	}
+
+	/* info1 will contain the offending cmd_no */
+	switch (info1) {
+	case CMD_SET_CTRL_MODE:
+		dev_warn(&dev->intf->dev,
+			 "CMD_SET_CTRL_MODE error in parameter\n");
+		break;
+
+	case CMD_SET_BUS_PARAMS:
+		dev_warn(&dev->intf->dev,
+			 "CMD_SET_BUS_PARAMS error in parameter\n");
+		break;
+
+	default:
+		dev_warn(&dev->intf->dev,
+			 "Unhandled parameter error event cmd_no (%u)\n",
+			 info1);
+		break;
+	}
+}
+
+static void kvaser_usb_leaf_error_event(const struct kvaser_usb *dev,
+					const struct kvaser_cmd *cmd)
+{
+	u8 error_code = 0;
+
+	switch (dev->driver_info->family) {
+	case KVASER_LEAF:
+		error_code = cmd->u.leaf.error_event.error_code;
+		break;
+	case KVASER_USBCAN:
+		error_code = cmd->u.usbcan.error_event.error_code;
+		break;
+	}
+
+	switch (error_code) {
+	case KVASER_USB_LEAF_ERROR_EVENT_TX_QUEUE_FULL:
+		/* Received additional CAN message, when firmware TX queue is
+		 * already full. Something is wrong with the driver.
+		 * This should never happen!
+		 */
+		dev_err(&dev->intf->dev,
+			"Received error event TX_QUEUE_FULL\n");
+		break;
+	case KVASER_USB_LEAF_ERROR_EVENT_PARAM:
+		kvaser_usb_leaf_error_event_parameter(dev, cmd);
+		break;
+
+	default:
+		dev_warn(&dev->intf->dev,
+			 "Unhandled error event (%d)\n", error_code);
+		break;
+	}
+}
+
 static void kvaser_usb_leaf_start_chip_reply(const struct kvaser_usb *dev,
 					     const struct kvaser_cmd *cmd)
 {
@@ -1049,9 +1467,31 @@
 	complete(&priv->stop_comp);
 }
 
+static void kvaser_usb_leaf_get_busparams_reply(const struct kvaser_usb *dev,
+						const struct kvaser_cmd *cmd)
+{
+	struct kvaser_usb_net_priv *priv;
+	u8 channel = cmd->u.busparams.channel;
+
+	if (channel >= dev->nchannels) {
+		dev_err(&dev->intf->dev,
+			"Invalid channel number (%d)\n", channel);
+		return;
+	}
+
+	priv = dev->nets[channel];
+	memcpy(&priv->busparams_nominal, &cmd->u.busparams.busparams,
+	       sizeof(priv->busparams_nominal));
+
+	complete(&priv->get_busparams_comp);
+}
+
 static void kvaser_usb_leaf_handle_command(const struct kvaser_usb *dev,
 					   const struct kvaser_cmd *cmd)
 {
+	if (kvaser_usb_leaf_verify_size(dev, cmd) < 0)
+		return;
+
 	switch (cmd->id) {
 	case CMD_START_CHIP_REPLY:
 		kvaser_usb_leaf_start_chip_reply(dev, cmd);
@@ -1067,14 +1507,14 @@
 		break;
 
 	case CMD_LEAF_LOG_MESSAGE:
-		if (dev->card_data.leaf.family != KVASER_LEAF)
+		if (dev->driver_info->family != KVASER_LEAF)
 			goto warn;
 		kvaser_usb_leaf_rx_can_msg(dev, cmd);
 		break;
 
 	case CMD_CHIP_STATE_EVENT:
 	case CMD_CAN_ERROR_EVENT:
-		if (dev->card_data.leaf.family == KVASER_LEAF)
+		if (dev->driver_info->family == KVASER_LEAF)
 			kvaser_usb_leaf_leaf_rx_error(dev, cmd);
 		else
 			kvaser_usb_leaf_usbcan_rx_error(dev, cmd);
@@ -1084,14 +1524,22 @@
 		kvaser_usb_leaf_tx_acknowledge(dev, cmd);
 		break;
 
+	case CMD_ERROR_EVENT:
+		kvaser_usb_leaf_error_event(dev, cmd);
+		break;
+
+	case CMD_GET_BUS_PARAMS_REPLY:
+		kvaser_usb_leaf_get_busparams_reply(dev, cmd);
+		break;
+
 	/* Ignored commands */
 	case CMD_USBCAN_CLOCK_OVERFLOW_EVENT:
-		if (dev->card_data.leaf.family != KVASER_USBCAN)
+		if (dev->driver_info->family != KVASER_USBCAN)
 			goto warn;
 		break;
 
 	case CMD_FLUSH_QUEUE_REPLY:
-		if (dev->card_data.leaf.family != KVASER_LEAF)
+		if (dev->driver_info->family != KVASER_LEAF)
 			goto warn;
 		break;
 
@@ -1164,7 +1612,7 @@
 {
 	int err;
 
-	init_completion(&priv->start_comp);
+	reinit_completion(&priv->start_comp);
 
 	err = kvaser_usb_leaf_send_simple_cmd(priv->dev, CMD_START_CHIP,
 					      priv->channel);
@@ -1180,9 +1628,12 @@
 
 static int kvaser_usb_leaf_stop_chip(struct kvaser_usb_net_priv *priv)
 {
+	struct kvaser_usb_net_leaf_priv *leaf = priv->sub_priv;
 	int err;
 
-	init_completion(&priv->stop_comp);
+	reinit_completion(&priv->stop_comp);
+
+	cancel_delayed_work(&leaf->chip_state_req_work);
 
 	err = kvaser_usb_leaf_send_simple_cmd(priv->dev, CMD_STOP_CHIP,
 					      priv->channel);
@@ -1225,28 +1676,40 @@
 {
 	struct kvaser_usb_dev_card_data *card_data = &dev->card_data;
 
-	dev->cfg = &kvaser_usb_leaf_dev_cfg;
 	card_data->ctrlmode_supported |= CAN_CTRLMODE_3_SAMPLES;
 
 	return 0;
 }
 
-static const struct can_bittiming_const kvaser_usb_leaf_bittiming_const = {
-	.name = "kvaser_usb",
-	.tseg1_min = KVASER_USB_TSEG1_MIN,
-	.tseg1_max = KVASER_USB_TSEG1_MAX,
-	.tseg2_min = KVASER_USB_TSEG2_MIN,
-	.tseg2_max = KVASER_USB_TSEG2_MAX,
-	.sjw_max = KVASER_USB_SJW_MAX,
-	.brp_min = KVASER_USB_BRP_MIN,
-	.brp_max = KVASER_USB_BRP_MAX,
-	.brp_inc = KVASER_USB_BRP_INC,
-};
+static int kvaser_usb_leaf_init_channel(struct kvaser_usb_net_priv *priv)
+{
+	struct kvaser_usb_net_leaf_priv *leaf;
+
+	leaf = devm_kzalloc(&priv->dev->intf->dev, sizeof(*leaf), GFP_KERNEL);
+	if (!leaf)
+		return -ENOMEM;
 
-static int kvaser_usb_leaf_set_bittiming(struct net_device *netdev)
+	leaf->net = priv;
+	INIT_DELAYED_WORK(&leaf->chip_state_req_work,
+			  kvaser_usb_leaf_chip_state_req_work);
+
+	priv->sub_priv = leaf;
+
+	return 0;
+}
+
+static void kvaser_usb_leaf_remove_channel(struct kvaser_usb_net_priv *priv)
+{
+	struct kvaser_usb_net_leaf_priv *leaf = priv->sub_priv;
+
+	if (leaf)
+		cancel_delayed_work_sync(&leaf->chip_state_req_work);
+}
+
+static int kvaser_usb_leaf_set_bittiming(const struct net_device *netdev,
+					 const struct kvaser_usb_busparams *busparams)
 {
 	struct kvaser_usb_net_priv *priv = netdev_priv(netdev);
-	struct can_bittiming *bt = &priv->can.bittiming;
 	struct kvaser_usb *dev = priv->dev;
 	struct kvaser_cmd *cmd;
 	int rc;
@@ -1259,15 +1722,8 @@
 	cmd->len = CMD_HEADER_LEN + sizeof(struct kvaser_cmd_busparams);
 	cmd->u.busparams.channel = priv->channel;
 	cmd->u.busparams.tid = 0xff;
-	cmd->u.busparams.bitrate = cpu_to_le32(bt->bitrate);
-	cmd->u.busparams.sjw = bt->sjw;
-	cmd->u.busparams.tseg1 = bt->prop_seg + bt->phase_seg1;
-	cmd->u.busparams.tseg2 = bt->phase_seg2;
-
-	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
-		cmd->u.busparams.no_samp = 3;
-	else
-		cmd->u.busparams.no_samp = 1;
+	memcpy(&cmd->u.busparams.busparams, busparams,
+	       sizeof(cmd->u.busparams.busparams));
 
 	rc = kvaser_usb_send_cmd(dev, cmd, cmd->len);
 
@@ -1275,6 +1731,27 @@
 	return rc;
 }
 
+static int kvaser_usb_leaf_get_busparams(struct kvaser_usb_net_priv *priv)
+{
+	int err;
+
+	if (priv->dev->driver_info->family == KVASER_USBCAN)
+		return -EOPNOTSUPP;
+
+	reinit_completion(&priv->get_busparams_comp);
+
+	err = kvaser_usb_leaf_send_simple_cmd(priv->dev, CMD_GET_BUS_PARAMS,
+					      priv->channel);
+	if (err)
+		return err;
+
+	if (!wait_for_completion_timeout(&priv->get_busparams_comp,
+					 msecs_to_jiffies(KVASER_USB_TIMEOUT)))
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
 static int kvaser_usb_leaf_set_mode(struct net_device *netdev,
 				    enum can_mode mode)
 {
@@ -1283,9 +1760,13 @@
 
 	switch (mode) {
 	case CAN_MODE_START:
+		kvaser_usb_unlink_tx_urbs(priv);
+
 		err = kvaser_usb_leaf_simple_cmd_async(priv, CMD_START_CHIP);
 		if (err)
 			return err;
+
+		priv->can.state = CAN_STATE_ERROR_ACTIVE;
 		break;
 	default:
 		return -EOPNOTSUPP;
@@ -1332,14 +1813,18 @@
 const struct kvaser_usb_dev_ops kvaser_usb_leaf_dev_ops = {
 	.dev_set_mode = kvaser_usb_leaf_set_mode,
 	.dev_set_bittiming = kvaser_usb_leaf_set_bittiming,
+	.dev_get_busparams = kvaser_usb_leaf_get_busparams,
 	.dev_set_data_bittiming = NULL,
+	.dev_get_data_busparams = NULL,
 	.dev_get_berr_counter = kvaser_usb_leaf_get_berr_counter,
 	.dev_setup_endpoints = kvaser_usb_leaf_setup_endpoints,
 	.dev_init_card = kvaser_usb_leaf_init_card,
+	.dev_init_channel = kvaser_usb_leaf_init_channel,
+	.dev_remove_channel = kvaser_usb_leaf_remove_channel,
 	.dev_get_software_info = kvaser_usb_leaf_get_software_info,
 	.dev_get_software_details = NULL,
 	.dev_get_card_info = kvaser_usb_leaf_get_card_info,
-	.dev_get_capabilities = NULL,
+	.dev_get_capabilities = kvaser_usb_leaf_get_capabilities,
 	.dev_set_opt_mode = kvaser_usb_leaf_set_opt_mode,
 	.dev_start_chip = kvaser_usb_leaf_start_chip,
 	.dev_stop_chip = kvaser_usb_leaf_stop_chip,
@@ -1348,11 +1833,3 @@
 	.dev_read_bulk_callback = kvaser_usb_leaf_read_bulk_callback,
 	.dev_frame_to_cmd = kvaser_usb_leaf_frame_to_cmd,
 };
-
-static const struct kvaser_usb_dev_cfg kvaser_usb_leaf_dev_cfg = {
-	.clock = {
-		.freq = CAN_USB_CLOCK,
-	},
-	.timestamp_freq = 1,
-	.bittiming_const = &kvaser_usb_leaf_bittiming_const,
-};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/mcba_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/mcba_usb.c
@@ -33,10 +33,6 @@
 #define MCBA_USB_RX_BUFF_SIZE 64
 #define MCBA_USB_TX_BUFF_SIZE (sizeof(struct mcba_usb_msg))
 
-/* MCBA endpoint numbers */
-#define MCBA_USB_EP_IN 1
-#define MCBA_USB_EP_OUT 1
-
 /* Microchip command id */
 #define MBCA_CMD_RECEIVE_MESSAGE 0xE3
 #define MBCA_CMD_I_AM_ALIVE_FROM_CAN 0xF5
@@ -51,6 +47,10 @@
 #define MCBA_VER_REQ_USB 1
 #define MCBA_VER_REQ_CAN 2
 
+/* Drive the CAN_RES signal LOW "0" to activate R24 and R25 */
+#define MCBA_VER_TERMINATION_ON 0
+#define MCBA_VER_TERMINATION_OFF 1
+
 #define MCBA_SIDL_EXID_MASK 0x8
 #define MCBA_DLC_MASK 0xf
 #define MCBA_DLC_RTR_MASK 0x40
@@ -84,6 +84,8 @@
 	atomic_t free_ctx_cnt;
 	void *rxbuf[MCBA_MAX_RX_URBS];
 	dma_addr_t rxbuf_dma[MCBA_MAX_RX_URBS];
+	int rx_pipe;
+	int tx_pipe;
 };
 
 /* CAN frame */
@@ -272,10 +274,8 @@
 
 	memcpy(buf, usb_msg, MCBA_USB_TX_BUFF_SIZE);
 
-	usb_fill_bulk_urb(urb, priv->udev,
-			  usb_sndbulkpipe(priv->udev, MCBA_USB_EP_OUT), buf,
-			  MCBA_USB_TX_BUFF_SIZE, mcba_usb_write_bulk_callback,
-			  ctx);
+	usb_fill_bulk_urb(urb, priv->udev, priv->tx_pipe, buf, MCBA_USB_TX_BUFF_SIZE,
+			  mcba_usb_write_bulk_callback, ctx);
 
 	urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
 	usb_anchor_urb(urb, &priv->tx_submitted);
@@ -368,7 +368,6 @@
 xmit_failed:
 	can_free_echo_skb(priv->netdev, ctx->ndx, NULL);
 	mcba_usb_free_ctx(ctx);
-	dev_kfree_skb(skb);
 	stats->tx_dropped++;
 
 	return NETDEV_TX_OK;
@@ -474,7 +473,7 @@
 		priv->usb_ka_first_pass = false;
 	}
 
-	if (msg->termination_state)
+	if (msg->termination_state == MCBA_VER_TERMINATION_ON)
 		priv->can.termination = MCBA_TERMINATION_ENABLED;
 	else
 		priv->can.termination = MCBA_TERMINATION_DISABLED;
@@ -611,7 +610,7 @@
 resubmit_urb:
 
 	usb_fill_bulk_urb(urb, priv->udev,
-			  usb_rcvbulkpipe(priv->udev, MCBA_USB_EP_OUT),
+			  priv->rx_pipe,
 			  urb->transfer_buffer, MCBA_USB_RX_BUFF_SIZE,
 			  mcba_usb_read_bulk_callback, priv);
 
@@ -656,7 +655,7 @@
 		urb->transfer_dma = buf_dma;
 
 		usb_fill_bulk_urb(urb, priv->udev,
-				  usb_rcvbulkpipe(priv->udev, MCBA_USB_EP_IN),
+				  priv->rx_pipe,
 				  buf, MCBA_USB_RX_BUFF_SIZE,
 				  mcba_usb_read_bulk_callback, priv);
 		urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
@@ -794,9 +793,9 @@
 	};
 
 	if (term == MCBA_TERMINATION_ENABLED)
-		usb_msg.termination = 1;
+		usb_msg.termination = MCBA_VER_TERMINATION_ON;
 	else
-		usb_msg.termination = 0;
+		usb_msg.termination = MCBA_VER_TERMINATION_OFF;
 
 	mcba_usb_xmit_cmd(priv, (struct mcba_usb_msg *)&usb_msg);
 
@@ -810,6 +809,13 @@
 	struct mcba_priv *priv;
 	int err;
 	struct usb_device *usbdev = interface_to_usbdev(intf);
+	struct usb_endpoint_descriptor *in, *out;
+
+	err = usb_find_common_endpoints(intf->cur_altsetting, &in, &out, NULL, NULL);
+	if (err) {
+		dev_err(&intf->dev, "Can't find endpoints\n");
+		return err;
+	}
 
 	netdev = alloc_candev(sizeof(struct mcba_priv), MCBA_MAX_TX_URBS);
 	if (!netdev) {
@@ -855,6 +861,9 @@
 		goto cleanup_free_candev;
 	}
 
+	priv->rx_pipe = usb_rcvbulkpipe(priv->udev, in->bEndpointAddress);
+	priv->tx_pipe = usb_sndbulkpipe(priv->udev, out->bEndpointAddress);
+
 	devm_can_led_init(netdev);
 
 	/* Start USB dev only if we have successfully registered CAN device */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/peak_usb/pcan_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/peak_usb/pcan_usb.c
@@ -520,8 +520,6 @@
 				     &hwts->hwtstamp);
 	}
 
-	mc->netdev->stats.rx_packets++;
-	mc->netdev->stats.rx_bytes += cf->len;
 	netif_rx(skb);
 
 	return 0;
@@ -841,14 +839,14 @@
 	pdev->bec.rxerr = 0;
 	pdev->bec.txerr = 0;
 
-	/* be notified on error counter changes (if requested by user) */
-	if (dev->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING) {
-		err = pcan_usb_set_err_frame(dev, PCAN_USB_BERR_MASK);
-		if (err)
-			netdev_warn(dev->netdev,
-				    "Asking for BERR reporting error %u\n",
-				    err);
-	}
+	/* always ask the device for BERR reporting, to be able to switch from
+	 * WARNING to PASSIVE state
+	 */
+	err = pcan_usb_set_err_frame(dev, PCAN_USB_BERR_MASK);
+	if (err)
+		netdev_warn(dev->netdev,
+			    "Asking for BERR reporting error %u\n",
+			    err);
 
 	/* if revision greater than 3, can put silent mode on/off */
 	if (dev->device_rev > 3) {
@@ -986,7 +984,6 @@
 	.device_id = PCAN_USB_PRODUCT_ID,
 	.ctrl_count = 1,
 	.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES | CAN_CTRLMODE_LISTENONLY |
-			      CAN_CTRLMODE_BERR_REPORTING |
 			      CAN_CTRLMODE_CC_LEN8_DLC,
 	.clock = {
 		.freq = PCAN_USB_CRYSTAL_HZ / 2,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/peak_usb/pcan_usb_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/peak_usb/pcan_usb_core.c
@@ -205,6 +205,19 @@
 	return netif_rx(skb);
 }
 
+/* post received skb with native 64-bit hw timestamp */
+int peak_usb_netif_rx_64(struct sk_buff *skb, u32 ts_low, u32 ts_high)
+{
+	struct skb_shared_hwtstamps *hwts = skb_hwtstamps(skb);
+	u64 ns_ts;
+
+	ns_ts = (u64)ts_high << 32 | ts_low;
+	ns_ts *= NSEC_PER_USEC;
+	hwts->hwtstamp = ns_to_ktime(ns_ts);
+
+	return netif_rx(skb);
+}
+
 /*
  * callback for bulk Rx urb
  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/peak_usb/pcan_usb_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/peak_usb/pcan_usb_core.h
@@ -143,6 +143,7 @@
 void peak_usb_get_ts_time(struct peak_time_ref *time_ref, u32 ts, ktime_t *tv);
 int peak_usb_netif_rx(struct sk_buff *skb,
 		      struct peak_time_ref *time_ref, u32 ts_low);
+int peak_usb_netif_rx_64(struct sk_buff *skb, u32 ts_low, u32 ts_high);
 void peak_usb_async_complete(struct urb *urb);
 void peak_usb_restart_complete(struct peak_usb_device *dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/peak_usb/pcan_usb_fd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/peak_usb/pcan_usb_fd.c
@@ -515,7 +515,8 @@
 	netdev->stats.rx_packets++;
 	netdev->stats.rx_bytes += cfd->len;
 
-	peak_usb_netif_rx(skb, &usb_if->time_ref, le32_to_cpu(rm->ts_low));
+	peak_usb_netif_rx_64(skb, le32_to_cpu(rm->ts_low),
+			     le32_to_cpu(rm->ts_high));
 
 	return 0;
 }
@@ -576,10 +577,8 @@
 	if (!skb)
 		return -ENOMEM;
 
-	netdev->stats.rx_packets++;
-	netdev->stats.rx_bytes += cf->len;
-
-	peak_usb_netif_rx(skb, &usb_if->time_ref, le32_to_cpu(sm->ts_low));
+	peak_usb_netif_rx_64(skb, le32_to_cpu(sm->ts_low),
+			     le32_to_cpu(sm->ts_high));
 
 	return 0;
 }
@@ -629,7 +628,8 @@
 	cf->can_id |= CAN_ERR_CRTL;
 	cf->data[1] |= CAN_ERR_CRTL_RX_OVERFLOW;
 
-	peak_usb_netif_rx(skb, &usb_if->time_ref, le32_to_cpu(ov->ts_low));
+	peak_usb_netif_rx_64(skb, le32_to_cpu(ov->ts_low),
+			     le32_to_cpu(ov->ts_high));
 
 	netdev->stats.rx_over_errors++;
 	netdev->stats.rx_errors++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/peak_usb/pcan_usb_pro.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/peak_usb/pcan_usb_pro.c
@@ -660,8 +660,6 @@
 
 	hwts = skb_hwtstamps(skb);
 	peak_usb_get_ts_time(&usb_if->time_ref, le32_to_cpu(er->ts32), &hwts->hwtstamp);
-	netdev->stats.rx_packets++;
-	netdev->stats.rx_bytes += can_frame->len;
 	netif_rx(skb);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/ucan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/ucan.c
@@ -621,8 +621,10 @@
 		memcpy(cf->data, m->msg.can_msg.data, cf->len);
 
 	/* don't count error frames as real packets */
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
+	if (!(cf->can_id & CAN_ERR_FLAG)) {
+		stats->rx_packets++;
+		stats->rx_bytes += cf->len;
+	}
 
 	/* pass it to Linux */
 	netif_rx(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/usb/usb_8dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/usb/usb_8dev.c
@@ -442,15 +442,14 @@
 
 	if (rx_errors)
 		stats->rx_errors++;
-
-	cf->data[6] = txerr;
-	cf->data[7] = rxerr;
+	if (priv->can.state != CAN_STATE_BUS_OFF) {
+		cf->data[6] = txerr;
+		cf->data[7] = rxerr;
+	}
 
 	priv->bec.txerr = txerr;
 	priv->bec.rxerr = rxerr;
 
-	stats->rx_packets++;
-	stats->rx_bytes += cf->len;
 	netif_rx(skb);
 }
 
@@ -670,9 +669,20 @@
 	atomic_inc(&priv->active_tx_urbs);
 
 	err = usb_submit_urb(urb, GFP_ATOMIC);
-	if (unlikely(err))
-		goto failed;
-	else if (atomic_read(&priv->active_tx_urbs) >= MAX_TX_URBS)
+	if (unlikely(err)) {
+		can_free_echo_skb(netdev, context->echo_index, NULL);
+
+		usb_unanchor_urb(urb);
+		usb_free_coherent(priv->udev, size, buf, urb->transfer_dma);
+
+		atomic_dec(&priv->active_tx_urbs);
+
+		if (err == -ENODEV)
+			netif_device_detach(netdev);
+		else
+			netdev_warn(netdev, "failed tx_urb %d\n", err);
+		stats->tx_dropped++;
+	} else if (atomic_read(&priv->active_tx_urbs) >= MAX_TX_URBS)
 		/* Slow down tx path */
 		netif_stop_queue(netdev);
 
@@ -691,19 +701,6 @@
 
 	return NETDEV_TX_BUSY;
 
-failed:
-	can_free_echo_skb(netdev, context->echo_index, NULL);
-
-	usb_unanchor_urb(urb);
-	usb_free_coherent(priv->udev, size, buf, urb->transfer_dma);
-
-	atomic_dec(&priv->active_tx_urbs);
-
-	if (err == -ENODEV)
-		netif_device_detach(netdev);
-	else
-		netdev_warn(netdev, "failed tx_urb %d\n", err);
-
 nomembuf:
 	usb_free_urb(urb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/vxcan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/vxcan.c
@@ -148,7 +148,7 @@
 	dev->hard_header_len	= 0;
 	dev->addr_len		= 0;
 	dev->tx_queue_len	= 0;
-	dev->flags		= (IFF_NOARP|IFF_ECHO);
+	dev->flags		= IFF_NOARP;
 	dev->netdev_ops		= &vxcan_netdev_ops;
 	dev->needs_free_netdev	= true;
 
@@ -179,12 +179,7 @@
 
 		nla_peer = data[VXCAN_INFO_PEER];
 		ifmp = nla_data(nla_peer);
-		err = rtnl_nla_parse_ifla(peer_tb,
-					  nla_data(nla_peer) +
-					  sizeof(struct ifinfomsg),
-					  nla_len(nla_peer) -
-					  sizeof(struct ifinfomsg),
-					  NULL);
+		err = rtnl_nla_parse_ifinfomsg(peer_tb, nla_peer, extack);
 		if (err < 0)
 			return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/can/xilinx_can.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/can/xilinx_can.c
@@ -28,6 +28,7 @@
 #include <linux/can/error.h>
 #include <linux/can/led.h>
 #include <linux/pm_runtime.h>
+#include <linux/reset.h>
 
 #define DRIVER_NAME	"xilinx_can"
 
@@ -133,6 +134,8 @@
 #define XCAN_DLCR_BRS_MASK		0x04000000 /* BRS Mask in DLC */
 
 /* CAN register bit shift - XCAN_<REG>_<BIT>_SHIFT */
+#define XCAN_BRPR_TDCO_SHIFT_CANFD	8  /* Transmitter Delay Compensation Offset */
+#define XCAN_BRPR_TDCE_SHIFT_CANFD	16 /* Transmitter Delay Compensation (TDC) Enable */
 #define XCAN_BTR_SJW_SHIFT		7  /* Synchronous jump width */
 #define XCAN_BTR_TS2_SHIFT		4  /* Time segment 2 */
 #define XCAN_BTR_SJW_SHIFT_CANFD	16 /* Synchronous jump width */
@@ -142,6 +145,8 @@
 #define XCAN_DLCR_DLC_SHIFT		28 /* Data length code */
 #define XCAN_ESR_REC_SHIFT		8  /* Rx Error Count */
 
+#define XCAN_BRPR_TDCO_MAX		64 /* TDCO max value */
+
 /* CAN frame length constants */
 #define XCAN_FRAME_MAX_DATA_LEN		8
 #define XCANFD_DW_BYTES			4
@@ -161,6 +166,17 @@
 #define XCAN_FLAG_RX_FIFO_MULTI	0x0010
 #define XCAN_FLAG_CANFD_2	0x0020
 
+static bool tdc_enable;
+static u8 tdc_offset;
+
+module_param(tdc_enable, bool, 0644);
+module_param(tdc_offset, byte, 0644);
+
+MODULE_PARM_DESC(tdc_enable,
+		 "Transmitter Delay Compensation (TDC) Enable");
+MODULE_PARM_DESC(tdc_offset,
+		 "Transmitter Delay Compensation Offset");
+
 enum xcan_ip_type {
 	XAXI_CAN = 0,
 	XZYNQ_CANPS,
@@ -210,6 +226,7 @@
 	struct clk *bus_clk;
 	struct clk *can_clk;
 	struct xcan_devtype_data devtype;
+	struct reset_control *rstc;
 };
 
 /* CAN Bittiming constants as per Xilinx CAN specs */
@@ -239,7 +256,7 @@
 };
 
 /* AXI CANFD Data Bittiming constants as per AXI CANFD 1.0 specs */
-static struct can_bittiming_const xcan_data_bittiming_const_canfd = {
+static const struct can_bittiming_const xcan_data_bittiming_const_canfd = {
 	.name = DRIVER_NAME,
 	.tseg1_min = 1,
 	.tseg1_max = 16,
@@ -259,20 +276,20 @@
 	.tseg2_min = 1,
 	.tseg2_max = 128,
 	.sjw_max = 128,
-	.brp_min = 2,
+	.brp_min = 1,
 	.brp_max = 256,
 	.brp_inc = 1,
 };
 
 /* AXI CANFD 2.0 Data Bittiming constants as per AXI CANFD 2.0 spec */
-static struct can_bittiming_const xcan_data_bittiming_const_canfd2 = {
+static const struct can_bittiming_const xcan_data_bittiming_const_canfd2 = {
 	.name = DRIVER_NAME,
 	.tseg1_min = 1,
 	.tseg1_max = 32,
 	.tseg2_min = 1,
 	.tseg2_max = 16,
 	.sjw_max = 16,
-	.brp_min = 2,
+	.brp_min = 1,
 	.brp_max = 256,
 	.brp_inc = 1,
 };
@@ -425,6 +442,10 @@
 	    priv->devtype.cantype == XAXI_CANFD_2_0) {
 		/* Setting Baud Rate prescalar value in F_BRPR Register */
 		btr0 = dbt->brp - 1;
+		if (tdc_enable)
+			btr0 = btr0 |
+			tdc_offset << XCAN_BRPR_TDCO_SHIFT_CANFD |
+			tdc_enable << XCAN_BRPR_TDCE_SHIFT_CANFD;
 
 		/* Setting Time Segment 1 in BTR Register */
 		btr1 = dbt->prop_seg + dbt->phase_seg1 - 1;
@@ -516,8 +537,7 @@
  * @ndev:	Pointer to net_device structure
  * @mode:	Tells the mode of the driver
  *
- * This check the drivers state and calls the
- * the corresponding modes to set.
+ * This check the drivers state and calls the corresponding modes to set.
  *
  * Return: 0 on success and failure value on error
  */
@@ -966,13 +986,8 @@
 
 		xcan_set_error_state(ndev, new_state, skb ? cf : NULL);
 
-		if (skb) {
-			struct net_device_stats *stats = &ndev->stats;
-
-			stats->rx_packets++;
-			stats->rx_bytes += cf->len;
+		if (skb)
 			netif_rx(skb);
-		}
 	}
 }
 
@@ -982,7 +997,7 @@
  * @isr:	interrupt status register value
  *
  * This is the CAN error interrupt and it will
- * check the the type of error and forward the error
+ * check the type of error and forward the error
  * frame to upper layers.
  */
 static void xcan_err_interrupt(struct net_device *ndev, u32 isr)
@@ -1096,8 +1111,6 @@
 		if (skb) {
 			skb_cf->can_id |= cf.can_id;
 			memcpy(skb_cf->data, cf.data, CAN_ERR_DLC);
-			stats->rx_packets++;
-			stats->rx_bytes += CAN_ERR_DLC;
 			netif_rx(skb);
 		}
 	}
@@ -1219,10 +1232,11 @@
 	}
 
 	if (work_done < quota) {
-		napi_complete_done(napi, work_done);
-		ier = priv->read_reg(priv, XCAN_IER_OFFSET);
-		ier |= xcan_rx_int_mask(priv);
-		priv->write_reg(priv, XCAN_IER_OFFSET, ier);
+		if (napi_complete_done(napi, work_done)) {
+			ier = priv->read_reg(priv, XCAN_IER_OFFSET);
+			ier |= xcan_rx_int_mask(priv);
+			priv->write_reg(priv, XCAN_IER_OFFSET, ier);
+		}
 	}
 	return work_done;
 }
@@ -1743,6 +1757,17 @@
 	priv->can.do_get_berr_counter = xcan_get_berr_counter;
 	priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK |
 					CAN_CTRLMODE_BERR_REPORTING;
+	priv->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(priv->rstc)) {
+		dev_err(&pdev->dev, "Cannot get CAN reset.\n");
+		ret = PTR_ERR(priv->rstc);
+		goto err_free;
+	}
+
+	ret = reset_control_reset(priv->rstc);
+	if (ret)
+		goto err_free;
+
 
 	if (devtype->cantype == XAXI_CANFD)
 		priv->can.data_bittiming_const =
@@ -1762,7 +1787,12 @@
 	spin_lock_init(&priv->tx_lock);
 
 	/* Get IRQ for the device */
-	ndev->irq = platform_get_irq(pdev, 0);
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0)
+		goto err_reset;
+
+	ndev->irq = ret;
+
 	ndev->flags |= IFF_ECHO;	/* We support local echo */
 
 	platform_set_drvdata(pdev, ndev);
@@ -1774,14 +1804,14 @@
 	if (IS_ERR(priv->can_clk)) {
 		ret = dev_err_probe(&pdev->dev, PTR_ERR(priv->can_clk),
 				    "device clock not found\n");
-		goto err_free;
+		goto err_reset;
 	}
 
 	priv->bus_clk = devm_clk_get(&pdev->dev, devtype->bus_clk_name);
 	if (IS_ERR(priv->bus_clk)) {
 		ret = dev_err_probe(&pdev->dev, PTR_ERR(priv->bus_clk),
 				    "bus clock not found\n");
-		goto err_free;
+		goto err_reset;
 	}
 
 	priv->write_reg = xcan_write_reg_le;
@@ -1818,6 +1848,8 @@
 		priv->write_reg(priv, XCAN_AFR_2_ID_OFFSET, 0x00000000);
 		priv->write_reg(priv, XCAN_AFR_2_MASK_OFFSET, 0x00000000);
 	}
+	if (!(tdc_enable && tdc_offset <= XCAN_BRPR_TDCO_MAX))
+		netdev_warn(ndev, "TDC Offset value not in range ");
 
 	netdev_dbg(ndev, "reg_base=0x%p irq=%d clock=%d, tx buffers: actual %d, using %d\n",
 		   priv->reg_base, ndev->irq, priv->can.clock.freq,
@@ -1828,6 +1860,8 @@
 err_disableclks:
 	pm_runtime_put(priv->dev);
 	pm_runtime_disable(&pdev->dev);
+err_reset:
+	reset_control_assert(priv->rstc);
 err_free:
 	free_candev(ndev);
 err:
@@ -1850,6 +1884,7 @@
 	pm_runtime_disable(&pdev->dev);
 	netif_napi_del(&priv->napi);
 	free_candev(ndev);
+	reset_control_assert(priv->rstc);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/Kconfig
@@ -36,6 +36,7 @@
 config NET_DSA_MT7530
 	tristate "MediaTek MT753x and MT7621 Ethernet switch support"
 	select NET_DSA_TAG_MTK
+	select MEDIATEK_GE_PHY
 	help
 	  This enables support for the MediaTek MT7530, MT7531, and MT7621
 	  Ethernet switch chips.
@@ -89,6 +90,7 @@
 config NET_DSA_SMSC_LAN9303_I2C
 	tristate "SMSC/Microchip LAN9303 3-ports 10/100 ethernet switch in I2C managed mode"
 	depends on I2C
+	depends on VLAN_8021Q || VLAN_8021Q=n
 	select NET_DSA_SMSC_LAN9303
 	select REGMAP_I2C
 	help
@@ -98,6 +100,7 @@
 config NET_DSA_SMSC_LAN9303_MDIO
 	tristate "SMSC/Microchip LAN9303 3-ports 10/100 ethernet switch in MDIO managed mode"
 	select NET_DSA_SMSC_LAN9303
+	depends on VLAN_8021Q || VLAN_8021Q=n
 	help
 	  Enable access functions if the SMSC/Microchip LAN9303 is configured
 	  for MDIO managed mode.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/b53/b53_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/b53/b53_common.c
@@ -27,6 +27,7 @@
 #include <linux/phylink.h>
 #include <linux/etherdevice.h>
 #include <linux/if_bridge.h>
+#include <linux/if_vlan.h>
 #include <net/dsa.h>
 
 #include "b53_regs.h"
@@ -224,6 +225,9 @@
 
 #define B53_MIBS_58XX_SIZE	ARRAY_SIZE(b53_mibs_58xx)
 
+#define B53_MAX_MTU_25		(1536 - ETH_HLEN - VLAN_HLEN - ETH_FCS_LEN)
+#define B53_MAX_MTU		(9720 - ETH_HLEN - VLAN_HLEN - ETH_FCS_LEN)
+
 static int b53_do_vlan_op(struct b53_device *dev, u8 op)
 {
 	unsigned int i;
@@ -2221,17 +2225,25 @@
 	bool allow_10_100;
 
 	if (is5325(dev) || is5365(dev))
-		return -EOPNOTSUPP;
+		return 0;
+
+	if (!dsa_is_cpu_port(ds, port))
+		return 0;
 
-	enable_jumbo = (mtu >= JMS_MIN_SIZE);
-	allow_10_100 = (dev->chip_id == BCM583XX_DEVICE_ID);
+	enable_jumbo = (mtu > ETH_DATA_LEN);
+	allow_10_100 = !is63xx(dev);
 
 	return b53_set_jumbo(dev, enable_jumbo, allow_10_100);
 }
 
 static int b53_get_max_mtu(struct dsa_switch *ds, int port)
 {
-	return JMS_MAX_SIZE;
+	struct b53_device *dev = ds->priv;
+
+	if (is5325(dev) || is5365(dev))
+		return B53_MAX_MTU_25;
+
+	return B53_MAX_MTU;
 }
 
 static const struct dsa_switch_ops b53_switch_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/b53/b53_mmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/b53/b53_mmap.c
@@ -216,6 +216,18 @@
 	return 0;
 }
 
+static int b53_mmap_phy_read16(struct b53_device *dev, int addr, int reg,
+			       u16 *value)
+{
+	return -EIO;
+}
+
+static int b53_mmap_phy_write16(struct b53_device *dev, int addr, int reg,
+				u16 value)
+{
+	return -EIO;
+}
+
 static const struct b53_io_ops b53_mmap_ops = {
 	.read8 = b53_mmap_read8,
 	.read16 = b53_mmap_read16,
@@ -227,6 +239,8 @@
 	.write32 = b53_mmap_write32,
 	.write48 = b53_mmap_write48,
 	.write64 = b53_mmap_write64,
+	.phy_read16 = b53_mmap_phy_read16,
+	.phy_write16 = b53_mmap_phy_write16,
 };
 
 static int b53_mmap_probe_of(struct platform_device *pdev,
@@ -263,7 +277,7 @@
 		if (of_property_read_u32(of_port, "reg", &reg))
 			continue;
 
-		if (reg < B53_CPU_PORT)
+		if (reg < B53_N_PORTS)
 			pdata->enabled_ports |= BIT(reg);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/b53/b53_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/b53/b53_spi.c
@@ -349,6 +349,19 @@
 };
 MODULE_DEVICE_TABLE(of, b53_spi_of_match);
 
+static const struct spi_device_id b53_spi_ids[] = {
+	{ .name = "bcm5325" },
+	{ .name = "bcm5365" },
+	{ .name = "bcm5395" },
+	{ .name = "bcm5397" },
+	{ .name = "bcm5398" },
+	{ .name = "bcm53115" },
+	{ .name = "bcm53125" },
+	{ .name = "bcm53128" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, b53_spi_ids);
+
 static struct spi_driver b53_spi_driver = {
 	.driver = {
 		.name	= "b53-switch",
@@ -357,6 +370,7 @@
 	.probe	= b53_spi_probe,
 	.remove	= b53_spi_remove,
 	.shutdown = b53_spi_shutdown,
+	.id_table = b53_spi_ids,
 };
 
 module_spi_driver(b53_spi_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/bcm_sf2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/bcm_sf2.c
@@ -577,17 +577,16 @@
 	dn = of_find_compatible_node(NULL, NULL, "brcm,unimac-mdio");
 	priv->master_mii_bus = of_mdio_find_bus(dn);
 	if (!priv->master_mii_bus) {
-		of_node_put(dn);
-		return -EPROBE_DEFER;
+		err = -EPROBE_DEFER;
+		goto err_of_node_put;
 	}
 
-	get_device(&priv->master_mii_bus->dev);
 	priv->master_mii_dn = dn;
 
-	priv->slave_mii_bus = devm_mdiobus_alloc(ds->dev);
+	priv->slave_mii_bus = mdiobus_alloc();
 	if (!priv->slave_mii_bus) {
-		of_node_put(dn);
-		return -ENOMEM;
+		err = -ENOMEM;
+		goto err_put_master_mii_bus_dev;
 	}
 
 	priv->slave_mii_bus->priv = priv;
@@ -639,20 +638,32 @@
 			of_remove_property(child, prop);
 
 		phydev = of_phy_find_device(child);
-		if (phydev)
+		if (phydev) {
 			phy_device_remove(phydev);
+			phy_device_free(phydev);
+		}
 	}
 
 	err = mdiobus_register(priv->slave_mii_bus);
 	if (err && dn)
-		of_node_put(dn);
+		goto err_free_slave_mii_bus;
+
+	return 0;
 
+err_free_slave_mii_bus:
+	mdiobus_free(priv->slave_mii_bus);
+err_put_master_mii_bus_dev:
+	put_device(&priv->master_mii_bus->dev);
+err_of_node_put:
+	of_node_put(dn);
 	return err;
 }
 
 static void bcm_sf2_mdio_unregister(struct bcm_sf2_priv *priv)
 {
 	mdiobus_unregister(priv->slave_mii_bus);
+	mdiobus_free(priv->slave_mii_bus);
+	put_device(&priv->master_mii_bus->dev);
 	of_node_put(priv->master_mii_dn);
 }
 
@@ -793,6 +804,9 @@
 	struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
 	u32 reg, offset;
 
+	if (priv->wol_ports_mask & BIT(port))
+		return;
+
 	if (port != core_readl(priv, CORE_IMP0_PRT_ID)) {
 		if (priv->type == BCM4908_DEVICE_ID ||
 		    priv->type == BCM7445_DEVICE_ID)
@@ -859,6 +873,11 @@
 		if (duplex == DUPLEX_FULL)
 			reg |= DUPLX_MODE;
 
+		if (tx_pause)
+			reg |= TXFLOW_CNTL;
+		if (rx_pause)
+			reg |= RXFLOW_CNTL;
+
 		core_writel(priv, reg, offset);
 	}
 
@@ -1411,7 +1430,9 @@
 	if (IS_ERR(priv->clk))
 		return PTR_ERR(priv->clk);
 
-	clk_prepare_enable(priv->clk);
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
 
 	priv->clk_mdiv = devm_clk_get_optional(&pdev->dev, "sw_switch_mdiv");
 	if (IS_ERR(priv->clk_mdiv)) {
@@ -1419,7 +1440,9 @@
 		goto out_clk;
 	}
 
-	clk_prepare_enable(priv->clk_mdiv);
+	ret = clk_prepare_enable(priv->clk_mdiv);
+	if (ret)
+		goto out_clk;
 
 	ret = bcm_sf2_sw_rst(priv);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/bcm_sf2_cfp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/bcm_sf2_cfp.c
@@ -567,14 +567,14 @@
 static struct cfp_rule *bcm_sf2_cfp_rule_find(struct bcm_sf2_priv *priv,
 					      int port, u32 location)
 {
-	struct cfp_rule *rule = NULL;
+	struct cfp_rule *rule;
 
 	list_for_each_entry(rule, &priv->cfp.rules_list, next) {
 		if (rule->port == port && rule->fs.location == location)
-			break;
+			return rule;
 	}
 
-	return rule;
+	return NULL;
 }
 
 static int bcm_sf2_cfp_rule_cmp(struct bcm_sf2_priv *priv, int port,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/dsa_loop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/dsa_loop.c
@@ -376,6 +376,17 @@
 
 #define NUM_FIXED_PHYS	(DSA_LOOP_NUM_PORTS - 2)
 
+static void dsa_loop_phydevs_unregister(void)
+{
+	unsigned int i;
+
+	for (i = 0; i < NUM_FIXED_PHYS; i++)
+		if (!IS_ERR(phydevs[i])) {
+			fixed_phy_unregister(phydevs[i]);
+			phy_device_free(phydevs[i]);
+		}
+}
+
 static int __init dsa_loop_init(void)
 {
 	struct fixed_phy_status status = {
@@ -383,23 +394,23 @@
 		.speed = SPEED_100,
 		.duplex = DUPLEX_FULL,
 	};
-	unsigned int i;
+	unsigned int i, ret;
 
 	for (i = 0; i < NUM_FIXED_PHYS; i++)
 		phydevs[i] = fixed_phy_register(PHY_POLL, &status, NULL);
 
-	return mdio_driver_register(&dsa_loop_drv);
+	ret = mdio_driver_register(&dsa_loop_drv);
+	if (ret)
+		dsa_loop_phydevs_unregister();
+
+	return ret;
 }
 module_init(dsa_loop_init);
 
 static void __exit dsa_loop_exit(void)
 {
-	unsigned int i;
-
 	mdio_driver_unregister(&dsa_loop_drv);
-	for (i = 0; i < NUM_FIXED_PHYS; i++)
-		if (!IS_ERR(phydevs[i]))
-			fixed_phy_unregister(phydevs[i]);
+	dsa_loop_phydevs_unregister();
 }
 module_exit(dsa_loop_exit);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/hirschmann/hellcreek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/hirschmann/hellcreek.c
@@ -710,8 +710,9 @@
 	u16 meta = 0;
 
 	dev_dbg(hellcreek->dev, "Add static FDB entry: MAC=%pM, MASK=0x%02x, "
-		"OBT=%d, REPRIO_EN=%d, PRIO=%d\n", entry->mac, entry->portmask,
-		entry->is_obt, entry->reprio_en, entry->reprio_tc);
+		"OBT=%d, PASS_BLOCKED=%d, REPRIO_EN=%d, PRIO=%d\n", entry->mac,
+		entry->portmask, entry->is_obt, entry->pass_blocked,
+		entry->reprio_en, entry->reprio_tc);
 
 	/* Add mac address */
 	hellcreek_write(hellcreek, entry->mac[1] | (entry->mac[0] << 8), HR_FDBWDH);
@@ -722,6 +723,8 @@
 	meta |= entry->portmask << HR_FDBWRM0_PORTMASK_SHIFT;
 	if (entry->is_obt)
 		meta |= HR_FDBWRM0_OBT;
+	if (entry->pass_blocked)
+		meta |= HR_FDBWRM0_PASS_BLOCKED;
 	if (entry->reprio_en) {
 		meta |= HR_FDBWRM0_REPRIO_EN;
 		meta |= entry->reprio_tc << HR_FDBWRM0_REPRIO_TC_SHIFT;
@@ -1049,7 +1052,7 @@
 
 static int hellcreek_setup_fdb(struct hellcreek *hellcreek)
 {
-	static struct hellcreek_fdb_entry ptp = {
+	static struct hellcreek_fdb_entry l2_ptp = {
 		/* MAC: 01-1B-19-00-00-00 */
 		.mac	      = { 0x01, 0x1b, 0x19, 0x00, 0x00, 0x00 },
 		.portmask     = 0x03,	/* Management ports */
@@ -1060,24 +1063,94 @@
 		.reprio_tc    = 6,	/* TC: 6 as per IEEE 802.1AS */
 		.reprio_en    = 1,
 	};
-	static struct hellcreek_fdb_entry p2p = {
+	static struct hellcreek_fdb_entry udp4_ptp = {
+		/* MAC: 01-00-5E-00-01-81 */
+		.mac	      = { 0x01, 0x00, 0x5e, 0x00, 0x01, 0x81 },
+		.portmask     = 0x03,	/* Management ports */
+		.age	      = 0,
+		.is_obt	      = 0,
+		.pass_blocked = 0,
+		.is_static    = 1,
+		.reprio_tc    = 6,
+		.reprio_en    = 1,
+	};
+	static struct hellcreek_fdb_entry udp6_ptp = {
+		/* MAC: 33-33-00-00-01-81 */
+		.mac	      = { 0x33, 0x33, 0x00, 0x00, 0x01, 0x81 },
+		.portmask     = 0x03,	/* Management ports */
+		.age	      = 0,
+		.is_obt	      = 0,
+		.pass_blocked = 0,
+		.is_static    = 1,
+		.reprio_tc    = 6,
+		.reprio_en    = 1,
+	};
+	static struct hellcreek_fdb_entry l2_p2p = {
 		/* MAC: 01-80-C2-00-00-0E */
 		.mac	      = { 0x01, 0x80, 0xc2, 0x00, 0x00, 0x0e },
 		.portmask     = 0x03,	/* Management ports */
 		.age	      = 0,
 		.is_obt	      = 0,
-		.pass_blocked = 0,
+		.pass_blocked = 1,
 		.is_static    = 1,
 		.reprio_tc    = 6,	/* TC: 6 as per IEEE 802.1AS */
 		.reprio_en    = 1,
 	};
+	static struct hellcreek_fdb_entry udp4_p2p = {
+		/* MAC: 01-00-5E-00-00-6B */
+		.mac	      = { 0x01, 0x00, 0x5e, 0x00, 0x00, 0x6b },
+		.portmask     = 0x03,	/* Management ports */
+		.age	      = 0,
+		.is_obt	      = 0,
+		.pass_blocked = 1,
+		.is_static    = 1,
+		.reprio_tc    = 6,
+		.reprio_en    = 1,
+	};
+	static struct hellcreek_fdb_entry udp6_p2p = {
+		/* MAC: 33-33-00-00-00-6B */
+		.mac	      = { 0x33, 0x33, 0x00, 0x00, 0x00, 0x6b },
+		.portmask     = 0x03,	/* Management ports */
+		.age	      = 0,
+		.is_obt	      = 0,
+		.pass_blocked = 1,
+		.is_static    = 1,
+		.reprio_tc    = 6,
+		.reprio_en    = 1,
+	};
+	static struct hellcreek_fdb_entry stp = {
+		/* MAC: 01-80-C2-00-00-00 */
+		.mac	      = { 0x01, 0x80, 0xc2, 0x00, 0x00, 0x00 },
+		.portmask     = 0x03,	/* Management ports */
+		.age	      = 0,
+		.is_obt	      = 0,
+		.pass_blocked = 1,
+		.is_static    = 1,
+		.reprio_tc    = 6,
+		.reprio_en    = 1,
+	};
 	int ret;
 
 	mutex_lock(&hellcreek->reg_lock);
-	ret = __hellcreek_fdb_add(hellcreek, &ptp);
+	ret = __hellcreek_fdb_add(hellcreek, &l2_ptp);
+	if (ret)
+		goto out;
+	ret = __hellcreek_fdb_add(hellcreek, &udp4_ptp);
+	if (ret)
+		goto out;
+	ret = __hellcreek_fdb_add(hellcreek, &udp6_ptp);
+	if (ret)
+		goto out;
+	ret = __hellcreek_fdb_add(hellcreek, &l2_p2p);
+	if (ret)
+		goto out;
+	ret = __hellcreek_fdb_add(hellcreek, &udp4_p2p);
+	if (ret)
+		goto out;
+	ret = __hellcreek_fdb_add(hellcreek, &udp6_p2p);
 	if (ret)
 		goto out;
-	ret = __hellcreek_fdb_add(hellcreek, &p2p);
+	ret = __hellcreek_fdb_add(hellcreek, &stp);
 out:
 	mutex_unlock(&hellcreek->reg_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/hirschmann/hellcreek_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/hirschmann/hellcreek_ptp.c
@@ -300,6 +300,7 @@
 	const char *label, *state;
 	int ret = -EINVAL;
 
+	of_node_get(hellcreek->dev->of_node);
 	leds = of_find_node_by_name(hellcreek->dev->of_node, "leds");
 	if (!leds) {
 		dev_err(hellcreek->dev, "No LEDs specified in device tree!\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/lan9303-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/lan9303-core.c
@@ -6,10 +6,12 @@
 #include <linux/module.h>
 #include <linux/gpio/consumer.h>
 #include <linux/regmap.h>
+#include <linux/iopoll.h>
 #include <linux/mutex.h>
 #include <linux/mii.h>
 #include <linux/phy.h>
 #include <linux/if_bridge.h>
+#include <linux/if_vlan.h>
 #include <linux/etherdevice.h>
 
 #include "lan9303.h"
@@ -819,6 +821,8 @@
 	if (!chip->reset_gpio)
 		return;
 
+	gpiod_set_value_cansleep(chip->reset_gpio, 1);
+
 	if (chip->reset_duration != 0)
 		msleep(chip->reset_duration);
 
@@ -844,8 +848,34 @@
 static int lan9303_check_device(struct lan9303 *chip)
 {
 	int ret;
+	int err;
 	u32 reg;
 
+	/* In I2C-managed configurations this polling loop will clash with
+	 * switch's reading of EEPROM right after reset and this behaviour is
+	 * not configurable. While lan9303_read() already has quite long retry
+	 * timeout, seems not all cases are being detected as arbitration error.
+	 *
+	 * According to datasheet, EEPROM loader has 30ms timeout (in case of
+	 * missing EEPROM).
+	 *
+	 * Loading of the largest supported EEPROM is expected to take at least
+	 * 5.9s.
+	 */
+	err = read_poll_timeout(lan9303_read, ret,
+				!ret && reg & LAN9303_HW_CFG_READY,
+				20000, 6000000, false,
+				chip->regmap, LAN9303_HW_CFG, &reg);
+	if (ret) {
+		dev_err(chip->dev, "failed to read HW_CFG reg: %pe\n",
+			ERR_PTR(ret));
+		return ret;
+	}
+	if (err) {
+		dev_err(chip->dev, "HW_CFG not ready: 0x%08x\n", reg);
+		return err;
+	}
+
 	ret = lan9303_read(chip->regmap, LAN9303_CHIP_REV, &reg);
 	if (ret) {
 		dev_err(chip->dev, "failed to read chip revision register: %d\n",
@@ -958,7 +988,7 @@
 	{ .offset = LAN9303_MAC_TX_BRDCST_CNT_0, .name = "TxBroad", },
 	{ .offset = LAN9303_MAC_TX_PAUSE_CNT_0, .name = "TxPause", },
 	{ .offset = LAN9303_MAC_TX_MULCST_CNT_0, .name = "TxMulti", },
-	{ .offset = LAN9303_MAC_RX_UNDSZE_CNT_0, .name = "TxUnderRun", },
+	{ .offset = LAN9303_MAC_RX_UNDSZE_CNT_0, .name = "RxShort", },
 	{ .offset = LAN9303_MAC_TX_64_CNT_0, .name = "Tx64Byte", },
 	{ .offset = LAN9303_MAC_TX_127_CNT_0, .name = "Tx128Byte", },
 	{ .offset = LAN9303_MAC_TX_255_CNT_0, .name = "Tx256Byte", },
@@ -1002,9 +1032,11 @@
 		ret = lan9303_read_switch_port(
 			chip, port, lan9303_mib[u].offset, &reg);
 
-		if (ret)
+		if (ret) {
 			dev_warn(chip->dev, "Reading status port %d reg %u failed\n",
 				 port, lan9303_mib[u].offset);
+			reg = 0;
+		}
 		data[u] = reg;
 	}
 }
@@ -1083,21 +1115,27 @@
 static int lan9303_port_enable(struct dsa_switch *ds, int port,
 			       struct phy_device *phy)
 {
+	struct dsa_port *dp = dsa_to_port(ds, port);
 	struct lan9303 *chip = ds->priv;
 
-	if (!dsa_is_user_port(ds, port))
+	if (!dsa_port_is_user(dp))
 		return 0;
 
+	vlan_vid_add(dp->cpu_dp->master, htons(ETH_P_8021Q), port);
+
 	return lan9303_enable_processing_port(chip, port);
 }
 
 static void lan9303_port_disable(struct dsa_switch *ds, int port)
 {
+	struct dsa_port *dp = dsa_to_port(ds, port);
 	struct lan9303 *chip = ds->priv;
 
-	if (!dsa_is_user_port(ds, port))
+	if (!dsa_port_is_user(dp))
 		return;
 
+	vlan_vid_del(dp->cpu_dp->master, htons(ETH_P_8021Q), port);
+
 	lan9303_disable_processing_port(chip, port);
 	lan9303_phy_write(ds, chip->phy_addr_base + port, MII_BMCR, BMCR_PDOWN);
 }
@@ -1185,8 +1223,6 @@
 	struct lan9303 *chip = ds->priv;
 
 	dev_dbg(chip->dev, "%s(%d, %pM, %d)\n", __func__, port, addr, vid);
-	if (vid)
-		return -EOPNOTSUPP;
 
 	return lan9303_alr_add_port(chip, addr, port, false);
 }
@@ -1198,8 +1234,6 @@
 	struct lan9303 *chip = ds->priv;
 
 	dev_dbg(chip->dev, "%s(%d, %pM, %d)\n", __func__, port, addr, vid);
-	if (vid)
-		return -EOPNOTSUPP;
 	lan9303_alr_del_port(chip, addr, port);
 
 	return 0;
@@ -1309,7 +1343,7 @@
 				     struct device_node *np)
 {
 	chip->reset_gpio = devm_gpiod_get_optional(chip->dev, "reset",
-						   GPIOD_OUT_LOW);
+						   GPIOD_OUT_HIGH);
 	if (IS_ERR(chip->reset_gpio))
 		return PTR_ERR(chip->reset_gpio);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/lan9303_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/lan9303_mdio.c
@@ -32,7 +32,7 @@
 	struct lan9303_mdio *sw_dev = (struct lan9303_mdio *)ctx;
 
 	reg <<= 2; /* reg num to offset */
-	mutex_lock(&sw_dev->device->bus->mdio_lock);
+	mutex_lock_nested(&sw_dev->device->bus->mdio_lock, MDIO_MUTEX_NESTED);
 	lan9303_mdio_real_write(sw_dev->device, reg, val & 0xffff);
 	lan9303_mdio_real_write(sw_dev->device, reg + 2, (val >> 16) & 0xffff);
 	mutex_unlock(&sw_dev->device->bus->mdio_lock);
@@ -50,7 +50,7 @@
 	struct lan9303_mdio *sw_dev = (struct lan9303_mdio *)ctx;
 
 	reg <<= 2; /* reg num to offset */
-	mutex_lock(&sw_dev->device->bus->mdio_lock);
+	mutex_lock_nested(&sw_dev->device->bus->mdio_lock, MDIO_MUTEX_NESTED);
 	*val = lan9303_mdio_real_read(sw_dev->device, reg);
 	*val |= (lan9303_mdio_real_read(sw_dev->device, reg + 2) << 16);
 	mutex_unlock(&sw_dev->device->bus->mdio_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/lantiq_gswip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/lantiq_gswip.c
@@ -497,8 +497,9 @@
 static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np)
 {
 	struct dsa_switch *ds = priv->ds;
+	int err;
 
-	ds->slave_mii_bus = devm_mdiobus_alloc(priv->dev);
+	ds->slave_mii_bus = mdiobus_alloc();
 	if (!ds->slave_mii_bus)
 		return -ENOMEM;
 
@@ -511,7 +512,11 @@
 	ds->slave_mii_bus->parent = priv->dev;
 	ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask;
 
-	return of_mdiobus_register(ds->slave_mii_bus, mdio_np);
+	err = of_mdiobus_register(ds->slave_mii_bus, mdio_np);
+	if (err)
+		mdiobus_free(ds->slave_mii_bus);
+
+	return err;
 }
 
 static int gswip_pce_table_entry_read(struct gswip_priv *priv,
@@ -1658,9 +1663,6 @@
 		break;
 	case PHY_INTERFACE_MODE_RMII:
 		miicfg |= GSWIP_MII_CFG_MODE_RMIIM;
-
-		/* Configure the RMII clock as output: */
-		miicfg |= GSWIP_MII_CFG_RMII_CLK;
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
 	case PHY_INTERFACE_MODE_RGMII_ID:
@@ -2045,8 +2047,10 @@
 	for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) {
 		err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i],
 					  gphy_fw_np, i);
-		if (err)
+		if (err) {
+			of_node_put(gphy_fw_np);
 			goto remove_gphy;
+		}
 		i++;
 	}
 
@@ -2170,8 +2174,10 @@
 	gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB);
 	dsa_unregister_switch(priv->ds);
 mdio_bus:
-	if (mdio_np)
+	if (mdio_np) {
 		mdiobus_unregister(priv->ds->slave_mii_bus);
+		mdiobus_free(priv->ds->slave_mii_bus);
+	}
 put_mdio_node:
 	of_node_put(mdio_np);
 	for (i = 0; i < priv->num_gphy_fw; i++)
@@ -2195,6 +2201,7 @@
 	if (priv->ds->slave_mii_bus) {
 		mdiobus_unregister(priv->ds->slave_mii_bus);
 		of_node_put(priv->ds->slave_mii_bus->dev.of_node);
+		mdiobus_free(priv->ds->slave_mii_bus);
 	}
 
 	for (i = 0; i < priv->num_gphy_fw; i++)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/microchip/ksz8795.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/microchip/ksz8795.c
@@ -25,6 +25,8 @@
 #include "ksz8795_reg.h"
 #include "ksz8.h"
 
+#define KSZ8795_CHIP_ID         0x09
+
 static const u8 ksz8795_regs[] = {
 	[REG_IND_CTRL_0]		= 0x6E,
 	[REG_IND_DATA_8]		= 0x70,
@@ -52,13 +54,13 @@
 	[STATIC_MAC_TABLE_VALID]	= BIT(21),
 	[STATIC_MAC_TABLE_USE_FID]	= BIT(23),
 	[STATIC_MAC_TABLE_FID]		= GENMASK(30, 24),
-	[STATIC_MAC_TABLE_OVERRIDE]	= BIT(26),
-	[STATIC_MAC_TABLE_FWD_PORTS]	= GENMASK(24, 20),
+	[STATIC_MAC_TABLE_OVERRIDE]	= BIT(22),
+	[STATIC_MAC_TABLE_FWD_PORTS]	= GENMASK(20, 16),
 	[DYNAMIC_MAC_TABLE_ENTRIES_H]	= GENMASK(6, 0),
-	[DYNAMIC_MAC_TABLE_MAC_EMPTY]	= BIT(8),
+	[DYNAMIC_MAC_TABLE_MAC_EMPTY]	= BIT(7),
 	[DYNAMIC_MAC_TABLE_NOT_READY]	= BIT(7),
 	[DYNAMIC_MAC_TABLE_ENTRIES]	= GENMASK(31, 29),
-	[DYNAMIC_MAC_TABLE_FID]		= GENMASK(26, 20),
+	[DYNAMIC_MAC_TABLE_FID]		= GENMASK(22, 16),
 	[DYNAMIC_MAC_TABLE_SRC_PORT]	= GENMASK(26, 24),
 	[DYNAMIC_MAC_TABLE_TIMESTAMP]	= GENMASK(28, 27),
 };
@@ -601,7 +603,13 @@
 				shifts[STATIC_MAC_FWD_PORTS];
 		alu->is_override =
 			(data_hi & masks[STATIC_MAC_TABLE_OVERRIDE]) ? 1 : 0;
-		data_hi >>= 1;
+
+		/* KSZ8795 family switches have STATIC_MAC_TABLE_USE_FID and
+		 * STATIC_MAC_TABLE_FID definitions off by 1 when doing read on the
+		 * static MAC table compared to doing write.
+		 */
+		if (dev->chip_id == KSZ8795_CHIP_ID)
+			data_hi >>= 1;
 		alu->is_static = true;
 		alu->is_use_fid =
 			(data_hi & masks[STATIC_MAC_TABLE_USE_FID]) ? 1 : 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/microchip/ksz8795_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/microchip/ksz8795_spi.c
@@ -124,12 +124,23 @@
 };
 MODULE_DEVICE_TABLE(of, ksz8795_dt_ids);
 
+static const struct spi_device_id ksz8795_spi_ids[] = {
+	{ "ksz8765" },
+	{ "ksz8794" },
+	{ "ksz8795" },
+	{ "ksz8863" },
+	{ "ksz8873" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, ksz8795_spi_ids);
+
 static struct spi_driver ksz8795_spi_driver = {
 	.driver = {
 		.name	= "ksz8795-switch",
 		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(ksz8795_dt_ids),
 	},
+	.id_table = ksz8795_spi_ids,
 	.probe	= ksz8795_spi_probe,
 	.remove	= ksz8795_spi_remove,
 	.shutdown = ksz8795_spi_shutdown,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/microchip/ksz8863_smi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/microchip/ksz8863_smi.c
@@ -86,22 +86,16 @@
 	{
 		.read = ksz8863_mdio_read,
 		.write = ksz8863_mdio_write,
-		.max_raw_read = 1,
-		.max_raw_write = 1,
 	},
 	{
 		.read = ksz8863_mdio_read,
 		.write = ksz8863_mdio_write,
 		.val_format_endian_default = REGMAP_ENDIAN_BIG,
-		.max_raw_read = 2,
-		.max_raw_write = 2,
 	},
 	{
 		.read = ksz8863_mdio_read,
 		.write = ksz8863_mdio_write,
 		.val_format_endian_default = REGMAP_ENDIAN_BIG,
-		.max_raw_read = 4,
-		.max_raw_write = 4,
 	}
 };
 
@@ -112,7 +106,6 @@
 		.pad_bits = 24,
 		.val_bits = 8,
 		.cache_type = REGCACHE_NONE,
-		.use_single_read = 1,
 		.lock = ksz_regmap_lock,
 		.unlock = ksz_regmap_unlock,
 	},
@@ -122,7 +115,6 @@
 		.pad_bits = 24,
 		.val_bits = 16,
 		.cache_type = REGCACHE_NONE,
-		.use_single_read = 1,
 		.lock = ksz_regmap_lock,
 		.unlock = ksz_regmap_unlock,
 	},
@@ -132,7 +124,6 @@
 		.pad_bits = 24,
 		.val_bits = 32,
 		.cache_type = REGCACHE_NONE,
-		.use_single_read = 1,
 		.lock = ksz_regmap_lock,
 		.unlock = ksz_regmap_unlock,
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/microchip/ksz9477.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/microchip/ksz9477.c
@@ -195,7 +195,6 @@
 
 static int ksz9477_reset_switch(struct ksz_device *dev)
 {
-	u8 data8;
 	u32 data32;
 
 	/* reset switch */
@@ -206,10 +205,8 @@
 			   SPI_AUTO_EDGE_DETECTION, 0);
 
 	/* default configuration */
-	ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8);
-	data8 = SW_AGING_ENABLE | SW_LINK_AUTO_AGING |
-	      SW_SRC_ADDR_FILTER | SW_FLUSH_STP_TABLE | SW_FLUSH_MSTP_TABLE;
-	ksz_write8(dev, REG_SW_LUE_CTRL_1, data8);
+	ksz_write8(dev, REG_SW_LUE_CTRL_1,
+		   SW_AGING_ENABLE | SW_LINK_AUTO_AGING | SW_SRC_ADDR_FILTER);
 
 	/* disable interrupts */
 	ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK);
@@ -675,10 +672,10 @@
 		ksz_read32(dev, REG_SW_ALU_VAL_D, &alu_table[3]);
 
 		/* clear forwarding port */
-		alu_table[2] &= ~BIT(port);
+		alu_table[1] &= ~BIT(port);
 
 		/* if there is no port to forward, clear table */
-		if ((alu_table[2] & ALU_V_PORT_MAP) == 0) {
+		if ((alu_table[1] & ALU_V_PORT_MAP) == 0) {
 			alu_table[0] = 0;
 			alu_table[1] = 0;
 			alu_table[2] = 0;
@@ -759,6 +756,9 @@
 			goto exit;
 		}
 
+		if (!(ksz_data & ALU_VALID))
+			continue;
+
 		/* read ALU table */
 		ksz9477_read_table(dev, alu_table);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/microchip/ksz9477_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/microchip/ksz9477_spi.c
@@ -98,12 +98,24 @@
 };
 MODULE_DEVICE_TABLE(of, ksz9477_dt_ids);
 
+static const struct spi_device_id ksz9477_spi_ids[] = {
+	{ "ksz9477" },
+	{ "ksz9897" },
+	{ "ksz9893" },
+	{ "ksz9563" },
+	{ "ksz8563" },
+	{ "ksz9567" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, ksz9477_spi_ids);
+
 static struct spi_driver ksz9477_spi_driver = {
 	.driver = {
 		.name	= "ksz9477-switch",
 		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(ksz9477_dt_ids),
 	},
+	.id_table = ksz9477_spi_ids,
 	.probe	= ksz9477_spi_probe,
 	.remove	= ksz9477_spi_remove,
 	.shutdown = ksz9477_spi_shutdown,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/microchip/ksz_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/microchip/ksz_common.c
@@ -414,18 +414,21 @@
 		ports = of_get_child_by_name(dev->dev->of_node, "ethernet-ports");
 		if (!ports)
 			ports = of_get_child_by_name(dev->dev->of_node, "ports");
-		if (ports)
+		if (ports) {
 			for_each_available_child_of_node(ports, port) {
 				if (of_property_read_u32(port, "reg",
 							 &port_num))
 					continue;
 				if (!(dev->port_mask & BIT(port_num))) {
 					of_node_put(port);
+					of_node_put(ports);
 					return -EINVAL;
 				}
 				of_get_phy_mode(port,
 						&dev->ports[port_num].interface);
 			}
+			of_node_put(ports);
+		}
 		dev->synclko_125 = of_property_read_bool(dev->dev->of_node,
 							 "microchip,synclko-125");
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mt7530.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mt7530.c
@@ -18,6 +18,7 @@
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
+#include <linux/bitfield.h>
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/driver.h>
 #include <net/dsa.h>
@@ -388,12 +389,52 @@
 		mt7530_write(priv, MT7530_ATA1 + (i * 4), reg[i]);
 }
 
-/* Setup TX circuit including relevant PAD and driving */
+/* Set up switch core clock for MT7530 */
+static void mt7530_pll_setup(struct mt7530_priv *priv)
+{
+	/* Disable core clock */
+	core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
+
+	/* Disable PLL */
+	core_write(priv, CORE_GSWPLL_GRP1, 0);
+
+	/* Set core clock into 500Mhz */
+	core_write(priv, CORE_GSWPLL_GRP2,
+		   RG_GSWPLL_POSDIV_500M(1) |
+		   RG_GSWPLL_FBKDIV_500M(25));
+
+	/* Enable PLL */
+	core_write(priv, CORE_GSWPLL_GRP1,
+		   RG_GSWPLL_EN_PRE |
+		   RG_GSWPLL_POSDIV_200M(2) |
+		   RG_GSWPLL_FBKDIV_200M(32));
+
+	udelay(20);
+
+	/* Enable core clock */
+	core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
+}
+
+/* If port 6 is available as a CPU port, always prefer that as the default,
+ * otherwise don't care.
+ */
+static struct dsa_port *
+mt753x_preferred_default_local_cpu_port(struct dsa_switch *ds)
+{
+	struct dsa_port *cpu_dp = dsa_to_port(ds, 6);
+
+	if (dsa_port_is_cpu(cpu_dp))
+		return cpu_dp;
+
+	return NULL;
+}
+
+/* Setup port 6 interface mode and TRGMII TX circuit */
 static int
 mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
-	u32 ncpo1, ssc_delta, trgint, i, xtal;
+	u32 ncpo1, ssc_delta, trgint, xtal;
 
 	xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
 
@@ -407,15 +448,17 @@
 	switch (interface) {
 	case PHY_INTERFACE_MODE_RGMII:
 		trgint = 0;
-		/* PLL frequency: 125MHz */
-		ncpo1 = 0x0c80;
 		break;
 	case PHY_INTERFACE_MODE_TRGMII:
 		trgint = 1;
+		if (xtal == HWTRAP_XTAL_25MHZ)
+			ssc_delta = 0x57;
+		else
+			ssc_delta = 0x87;
 		if (priv->id == ID_MT7621) {
-			/* PLL frequency: 150MHz: 1.2GBit */
+			/* PLL frequency: 125MHz: 1.0GBit */
 			if (xtal == HWTRAP_XTAL_40MHZ)
-				ncpo1 = 0x0780;
+				ncpo1 = 0x0640;
 			if (xtal == HWTRAP_XTAL_25MHZ)
 				ncpo1 = 0x0a00;
 		} else { /* PLL frequency: 250MHz: 2.0Gbit */
@@ -431,61 +474,32 @@
 		return -EINVAL;
 	}
 
-	if (xtal == HWTRAP_XTAL_25MHZ)
-		ssc_delta = 0x57;
-	else
-		ssc_delta = 0x87;
-
 	mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
 		   P6_INTF_MODE(trgint));
 
-	/* Lower Tx Driving for TRGMII path */
-	for (i = 0 ; i < NUM_TRGMII_CTRL ; i++)
-		mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),
-			     TD_DM_DRVP(8) | TD_DM_DRVN(8));
-
-	/* Disable MT7530 core and TRGMII Tx clocks */
-	core_clear(priv, CORE_TRGMII_GSW_CLK_CG,
-		   REG_GSWCK_EN | REG_TRGMIICK_EN);
-
-	/* Setup core clock for MT7530 */
-	/* Disable PLL */
-	core_write(priv, CORE_GSWPLL_GRP1, 0);
-
-	/* Set core clock into 500Mhz */
-	core_write(priv, CORE_GSWPLL_GRP2,
-		   RG_GSWPLL_POSDIV_500M(1) |
-		   RG_GSWPLL_FBKDIV_500M(25));
+	if (trgint) {
+		/* Disable the MT7530 TRGMII clocks */
+		core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
+
+		/* Setup the MT7530 TRGMII Tx Clock */
+		core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
+		core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
+		core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
+		core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
+		core_write(priv, CORE_PLL_GROUP4,
+			   RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
+			   RG_SYSPLL_BIAS_LPF_EN);
+		core_write(priv, CORE_PLL_GROUP2,
+			   RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
+			   RG_SYSPLL_POSDIV(1));
+		core_write(priv, CORE_PLL_GROUP7,
+			   RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
+			   RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
 
-	/* Enable PLL */
-	core_write(priv, CORE_GSWPLL_GRP1,
-		   RG_GSWPLL_EN_PRE |
-		   RG_GSWPLL_POSDIV_200M(2) |
-		   RG_GSWPLL_FBKDIV_200M(32));
+		/* Enable the MT7530 TRGMII clocks */
+		core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
+	}
 
-	/* Setup the MT7530 TRGMII Tx Clock */
-	core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
-	core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
-	core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
-	core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
-	core_write(priv, CORE_PLL_GROUP4,
-		   RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
-		   RG_SYSPLL_BIAS_LPF_EN);
-	core_write(priv, CORE_PLL_GROUP2,
-		   RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
-		   RG_SYSPLL_POSDIV(1));
-	core_write(priv, CORE_PLL_GROUP7,
-		   RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
-		   RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
-
-	/* Enable MT7530 core and TRGMII Tx clocks */
-	core_set(priv, CORE_TRGMII_GSW_CLK_CG,
-		 REG_GSWCK_EN | REG_TRGMIICK_EN);
-
-	if (!trgint)
-		for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
-			mt7530_rmw(priv, MT7530_TRGMII_RD(i),
-				   RD_TAP_MASK, RD_TAP(16));
 	return 0;
 }
 
@@ -501,14 +515,19 @@
 static int
 mt7531_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
 {
-	struct mt7530_priv *priv = ds->priv;
+	return 0;
+}
+
+static void
+mt7531_pll_setup(struct mt7530_priv *priv)
+{
 	u32 top_sig;
 	u32 hwstrap;
 	u32 xtal;
 	u32 val;
 
 	if (mt7531_dual_sgmii_supported(priv))
-		return 0;
+		return;
 
 	val = mt7530_read(priv, MT7531_CREV);
 	top_sig = mt7530_read(priv, MT7531_TOP_SIG_SR);
@@ -587,8 +606,6 @@
 	val |= EN_COREPLL;
 	mt7530_write(priv, MT7531_PLLGP_EN, val);
 	usleep_range(25, 35);
-
-	return 0;
 }
 
 static void
@@ -991,6 +1008,219 @@
 	mutex_unlock(&priv->reg_mutex);
 }
 
+/* In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer (DLL)
+ * of the Open Systems Interconnection basic reference model (OSI/RM) are
+ * described; the medium access control (MAC) and logical link control (LLC)
+ * sublayers. The MAC sublayer is the one facing the physical layer.
+ *
+ * In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
+ * Bridge component comprises a MAC Relay Entity for interconnecting the Ports
+ * of the Bridge, at least two Ports, and higher layer entities with at least a
+ * Spanning Tree Protocol Entity included.
+ *
+ * Each Bridge Port also functions as an end station and shall provide the MAC
+ * Service to an LLC Entity. Each instance of the MAC Service is provided to a
+ * distinct LLC Entity that supports protocol identification, multiplexing, and
+ * demultiplexing, for protocol data unit (PDU) transmission and reception by
+ * one or more higher layer entities.
+ *
+ * It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
+ * Entity associated with each Bridge Port is modeled as being directly
+ * connected to the attached Local Area Network (LAN).
+ *
+ * On the switch with CPU port architecture, CPU port functions as Management
+ * Port, and the Management Port functionality is provided by software which
+ * functions as an end station. Software is connected to an IEEE 802 LAN that is
+ * wholly contained within the system that incorporates the Bridge. Software
+ * provides access to the LLC Entity associated with each Bridge Port by the
+ * value of the source port field on the special tag on the frame received by
+ * software.
+ *
+ * We call frames that carry control information to determine the active
+ * topology and current extent of each Virtual Local Area Network (VLAN), i.e.,
+ * spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN Registration
+ * Protocol Data Units (MVRPDUs), and frames from other link constrained
+ * protocols, such as Extensible Authentication Protocol over LAN (EAPOL) and
+ * Link Layer Discovery Protocol (LLDP), link-local frames. They are not
+ * forwarded by a Bridge. Permanently configured entries in the filtering
+ * database (FDB) ensure that such frames are discarded by the Forwarding
+ * Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in detail:
+ *
+ * Each of the reserved MAC addresses specified in Table 8-1
+ * (01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
+ * permanently configured in the FDB in C-VLAN components and ERs.
+ *
+ * Each of the reserved MAC addresses specified in Table 8-2
+ * (01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
+ * configured in the FDB in S-VLAN components.
+ *
+ * Each of the reserved MAC addresses specified in Table 8-3
+ * (01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB in
+ * TPMR components.
+ *
+ * The FDB entries for reserved MAC addresses shall specify filtering for all
+ * Bridge Ports and all VIDs. Management shall not provide the capability to
+ * modify or remove entries for reserved MAC addresses.
+ *
+ * The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
+ * propagation of PDUs within a Bridged Network, as follows:
+ *
+ *   The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that no
+ *   conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
+ *   component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
+ *   PDUs transmitted using this destination address, or any other addresses
+ *   that appear in Table 8-1, Table 8-2, and Table 8-3
+ *   (01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
+ *   therefore travel no further than those stations that can be reached via a
+ *   single individual LAN from the originating station.
+ *
+ *   The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
+ *   address that no conformant S-VLAN component, C-VLAN component, or MAC
+ *   Bridge can forward; however, this address is relayed by a TPMR component.
+ *   PDUs using this destination address, or any of the other addresses that
+ *   appear in both Table 8-1 and Table 8-2 but not in Table 8-3
+ *   (01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed by
+ *   any TPMRs but will propagate no further than the nearest S-VLAN component,
+ *   C-VLAN component, or MAC Bridge.
+ *
+ *   The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an address
+ *   that no conformant C-VLAN component, MAC Bridge can forward; however, it is
+ *   relayed by TPMR components and S-VLAN components. PDUs using this
+ *   destination address, or any of the other addresses that appear in Table 8-1
+ *   but not in either Table 8-2 or Table 8-3 (01-80-C2-00-00-[00,0B,0C,0D,0F]),
+ *   will be relayed by TPMR components and S-VLAN components but will propagate
+ *   no further than the nearest C-VLAN component or MAC Bridge.
+ *
+ * Because the LLC Entity associated with each Bridge Port is provided via CPU
+ * port, we must not filter these frames but forward them to CPU port.
+ *
+ * In a Bridge, the transmission Port is majorly decided by ingress and egress
+ * rules, FDB, and spanning tree Port State functions of the Forwarding Process.
+ * For link-local frames, only CPU port should be designated as destination port
+ * in the FDB, and the other functions of the Forwarding Process must not
+ * interfere with the decision of the transmission Port. We call this process
+ * trapping frames to CPU port.
+ *
+ * Therefore, on the switch with CPU port architecture, link-local frames must
+ * be trapped to CPU port, and certain link-local frames received by a Port of a
+ * Bridge comprising a TPMR component or an S-VLAN component must be excluded
+ * from it.
+ *
+ * A Bridge of the switch with CPU port architecture cannot comprise a Two-Port
+ * MAC Relay (TPMR) component as a TPMR component supports only a subset of the
+ * functionality of a MAC Bridge. A Bridge comprising two Ports (Management Port
+ * doesn't count) of this architecture will either function as a standard MAC
+ * Bridge or a standard VLAN Bridge.
+ *
+ * Therefore, a Bridge of this architecture can only comprise S-VLAN components,
+ * C-VLAN components, or MAC Bridge components. Since there's no TPMR component,
+ * we don't need to relay PDUs using the destination addresses specified on the
+ * Nearest non-TPMR section, and the proportion of the Nearest Customer Bridge
+ * section where they must be relayed by TPMR components.
+ *
+ * One option to trap link-local frames to CPU port is to add static FDB entries
+ * with CPU port designated as destination port. However, because that
+ * Independent VLAN Learning (IVL) is being used on every VID, each entry only
+ * applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
+ * Bridge component or a C-VLAN component, there would have to be 16 times 4096
+ * entries. This switch intellectual property can only hold a maximum of 2048
+ * entries. Using this option, there also isn't a mechanism to prevent
+ * link-local frames from being discarded when the spanning tree Port State of
+ * the reception Port is discarding.
+ *
+ * The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
+ * registers. Whilst this applies to every VID, it doesn't contain all of the
+ * reserved MAC addresses without affecting the remaining Standard Group MAC
+ * Addresses. The REV_UN frame tag utilised using the RGAC4 register covers the
+ * remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
+ * addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
+ * destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
+ * The latter option provides better but not complete conformance.
+ *
+ * This switch intellectual property also does not provide a mechanism to trap
+ * link-local frames with specific destination addresses to CPU port by Bridge,
+ * to conform to the filtering rules for the distinct Bridge components.
+ *
+ * Therefore, regardless of the type of the Bridge component, link-local frames
+ * with these destination addresses will be trapped to CPU port:
+ *
+ * 01-80-C2-00-00-[00,01,02,03,0E]
+ *
+ * In a Bridge comprising a MAC Bridge component or a C-VLAN component:
+ *
+ *   Link-local frames with these destination addresses won't be trapped to CPU
+ *   port which won't conform to IEEE Std 802.1Q-2022:
+ *
+ *   01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]
+ *
+ * In a Bridge comprising an S-VLAN component:
+ *
+ *   Link-local frames with these destination addresses will be trapped to CPU
+ *   port which won't conform to IEEE Std 802.1Q-2022:
+ *
+ *   01-80-C2-00-00-00
+ *
+ *   Link-local frames with these destination addresses won't be trapped to CPU
+ *   port which won't conform to IEEE Std 802.1Q-2022:
+ *
+ *   01-80-C2-00-00-[04,05,06,07,08,09,0A]
+ *
+ * To trap link-local frames to CPU port as conformant as this switch
+ * intellectual property can allow, link-local frames are made to be regarded as
+ * Bridge Protocol Data Units (BPDUs). This is because this switch intellectual
+ * property only lets the frames regarded as BPDUs bypass the spanning tree Port
+ * State function of the Forwarding Process.
+ *
+ * The only remaining interference is the ingress rules. When the reception Port
+ * has no PVID assigned on software, VLAN-untagged frames won't be allowed in.
+ * There doesn't seem to be a mechanism on the switch intellectual property to
+ * have link-local frames bypass this function of the Forwarding Process.
+ */
+static void
+mt753x_trap_frames(struct mt7530_priv *priv)
+{
+	/* Trap 802.1X PAE frames and BPDUs to the CPU port(s) and egress them
+	 * VLAN-untagged.
+	 */
+	mt7530_rmw(priv, MT753X_BPC,
+		   MT753X_PAE_BPDU_FR | MT753X_PAE_EG_TAG_MASK |
+			   MT753X_PAE_PORT_FW_MASK | MT753X_BPDU_EG_TAG_MASK |
+			   MT753X_BPDU_PORT_FW_MASK,
+		   MT753X_PAE_BPDU_FR |
+			   MT753X_PAE_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+			   MT753X_PAE_PORT_FW(MT753X_BPDU_CPU_ONLY) |
+			   MT753X_BPDU_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+			   MT753X_BPDU_CPU_ONLY);
+
+	/* Trap frames with :01 and :02 MAC DAs to the CPU port(s) and egress
+	 * them VLAN-untagged.
+	 */
+	mt7530_rmw(priv, MT753X_RGAC1,
+		   MT753X_R02_BPDU_FR | MT753X_R02_EG_TAG_MASK |
+			   MT753X_R02_PORT_FW_MASK | MT753X_R01_BPDU_FR |
+			   MT753X_R01_EG_TAG_MASK | MT753X_R01_PORT_FW_MASK,
+		   MT753X_R02_BPDU_FR |
+			   MT753X_R02_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+			   MT753X_R02_PORT_FW(MT753X_BPDU_CPU_ONLY) |
+			   MT753X_R01_BPDU_FR |
+			   MT753X_R01_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+			   MT753X_BPDU_CPU_ONLY);
+
+	/* Trap frames with :03 and :0E MAC DAs to the CPU port(s) and egress
+	 * them VLAN-untagged.
+	 */
+	mt7530_rmw(priv, MT753X_RGAC2,
+		   MT753X_R0E_BPDU_FR | MT753X_R0E_EG_TAG_MASK |
+			   MT753X_R0E_PORT_FW_MASK | MT753X_R03_BPDU_FR |
+			   MT753X_R03_EG_TAG_MASK | MT753X_R03_PORT_FW_MASK,
+		   MT753X_R0E_BPDU_FR |
+			   MT753X_R0E_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+			   MT753X_R0E_PORT_FW(MT753X_BPDU_CPU_ONLY) |
+			   MT753X_R03_BPDU_FR |
+			   MT753X_R03_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+			   MT753X_BPDU_CPU_ONLY);
+}
+
 static int
 mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
 {
@@ -1008,14 +1238,21 @@
 	mt7530_write(priv, MT7530_PVC_P(port),
 		     PORT_SPEC_TAG);
 
-	/* Disable flooding by default */
-	mt7530_rmw(priv, MT7530_MFC, BC_FFP_MASK | UNM_FFP_MASK | UNU_FFP_MASK,
-		   BC_FFP(BIT(port)) | UNM_FFP(BIT(port)) | UNU_FFP(BIT(port)));
+	/* Enable flooding on the CPU port */
+	mt7530_set(priv, MT7530_MFC, BC_FFP(BIT(port)) | UNM_FFP(BIT(port)) |
+		   UNU_FFP(BIT(port)));
 
 	/* Set CPU port number */
-	if (priv->id == ID_MT7621)
+	if (priv->id == ID_MT7530 || priv->id == ID_MT7621)
 		mt7530_rmw(priv, MT7530_MFC, CPU_MASK, CPU_EN | CPU_PORT(port));
 
+	/* Add the CPU port to the CPU port bitmap for MT7531. Trapped frames
+	 * will be forwarded to the CPU port that is affine to the inbound user
+	 * port.
+	 */
+	if (priv->id == ID_MT7531)
+		mt7530_set(priv, MT7531_CFC, MT7531_CPU_PMAP(BIT(port)));
+
 	/* CPU port gets connected to all user ports of
 	 * the switch.
 	 */
@@ -1287,14 +1524,26 @@
 		if (!priv->ports[port].pvid)
 			mt7530_rmw(priv, MT7530_PVC_P(port), ACC_FRM_MASK,
 				   MT7530_VLAN_ACC_TAGGED);
-	}
 
-	/* Set the port as a user port which is to be able to recognize VID
-	 * from incoming packets before fetching entry within the VLAN table.
-	 */
-	mt7530_rmw(priv, MT7530_PVC_P(port), VLAN_ATTR_MASK | PVC_EG_TAG_MASK,
-		   VLAN_ATTR(MT7530_VLAN_USER) |
-		   PVC_EG_TAG(MT7530_VLAN_EG_DISABLED));
+		/* Set the port as a user port which is to be able to recognize
+		 * VID from incoming packets before fetching entry within the
+		 * VLAN table.
+		 */
+		mt7530_rmw(priv, MT7530_PVC_P(port),
+			   VLAN_ATTR_MASK | PVC_EG_TAG_MASK,
+			   VLAN_ATTR(MT7530_VLAN_USER) |
+			   PVC_EG_TAG(MT7530_VLAN_EG_DISABLED));
+	} else {
+		/* Also set CPU ports to the "user" VLAN port attribute, to
+		 * allow VLAN classification, but keep the EG_TAG attribute as
+		 * "consistent" (i.o.w. don't change its value) for packets
+		 * received by the switch from the CPU, so that tagged packets
+		 * are forwarded to user ports as tagged, and untagged as
+		 * untagged.
+		 */
+		mt7530_rmw(priv, MT7530_PVC_P(port), VLAN_ATTR_MASK,
+			   VLAN_ATTR(MT7530_VLAN_USER));
+	}
 }
 
 static void
@@ -2066,7 +2315,7 @@
 	if (priv->irq)
 		mt7530_setup_mdio_irq(priv);
 
-	ret = mdiobus_register(bus);
+	ret = devm_mdiobus_register(dev, bus);
 	if (ret) {
 		dev_err(dev, "failed to register MDIO bus: %d\n", ret);
 		if (priv->irq)
@@ -2080,11 +2329,12 @@
 mt7530_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
+	struct device_node *dn = NULL;
 	struct device_node *phy_node;
 	struct device_node *mac_np;
 	struct mt7530_dummy_poll p;
 	phy_interface_t interface;
-	struct device_node *dn;
+	struct dsa_port *cpu_dp;
 	u32 id, val;
 	int ret, i;
 
@@ -2092,7 +2342,19 @@
 	 * controller also is the container for two GMACs nodes representing
 	 * as two netdev instances.
 	 */
-	dn = dsa_to_port(ds, MT7530_CPU_PORT)->master->dev.of_node->parent;
+	dsa_switch_for_each_cpu_port(cpu_dp, ds) {
+		dn = cpu_dp->master->dev.of_node->parent;
+		/* It doesn't matter which CPU port is found first,
+		 * their masters should share the same parent OF node
+		 */
+		break;
+	}
+
+	if (!dn) {
+		dev_err(ds->dev, "parent OF node of DSA master not found");
+		return -EINVAL;
+	}
+
 	ds->assisted_learning_on_cpu_port = true;
 	ds->mtu_enforcement_ingress = true;
 
@@ -2119,11 +2381,11 @@
 	 */
 	if (priv->mcm) {
 		reset_control_assert(priv->rstc);
-		usleep_range(1000, 1100);
+		usleep_range(5000, 5100);
 		reset_control_deassert(priv->rstc);
 	} else {
 		gpiod_set_value_cansleep(priv->reset, 0);
-		usleep_range(1000, 1100);
+		usleep_range(5000, 5100);
 		gpiod_set_value_cansleep(priv->reset, 1);
 	}
 
@@ -2148,7 +2410,16 @@
 		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
 		     SYS_CTRL_REG_RST);
 
-	/* Enable Port 6 only; P5 as GMAC5 which currently is not supported */
+	/* Lower Tx driving for TRGMII path */
+	for (i = 0; i < NUM_TRGMII_CTRL; i++)
+		mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),
+			     TD_DM_DRVP(8) | TD_DM_DRVN(8));
+
+	for (i = 0; i < NUM_TRGMII_CTRL; i++)
+		mt7530_rmw(priv, MT7530_TRGMII_RD(i),
+			   RD_TAP_MASK, RD_TAP(16));
+
+	/* Enable port 6 */
 	val = mt7530_read(priv, MT7530_MHWTRAP);
 	val &= ~MHWTRAP_P6_DIS & ~MHWTRAP_PHY_ACCESS;
 	val |= MHWTRAP_MANUAL;
@@ -2156,6 +2427,11 @@
 
 	priv->p6_interface = PHY_INTERFACE_MODE_NA;
 
+	if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_40MHZ)
+		mt7530_pll_setup(priv);
+
+	mt753x_trap_frames(priv);
+
 	/* Enable and reset MIB counters */
 	mt7530_mib_reset(ds);
 
@@ -2183,6 +2459,9 @@
 			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
 	}
 
+	/* Allow mirroring frames received on the local port (monitor port). */
+	mt7530_set(priv, MT753X_AGC, LOCAL_EN);
+
 	/* Setup VLAN ID 0 for VLAN-unaware bridges */
 	ret = mt7530_setup_vlan0(priv);
 	if (ret)
@@ -2216,6 +2495,7 @@
 				ret = of_get_phy_mode(mac_np, &interface);
 				if (ret && ret != -ENODEV) {
 					of_node_put(mac_np);
+					of_node_put(phy_node);
 					return ret;
 				}
 				id = of_mdio_parse_addr(ds->dev, phy_node);
@@ -2249,6 +2529,59 @@
 }
 
 static int
+mt7531_setup_common(struct dsa_switch *ds)
+{
+	struct mt7530_priv *priv = ds->priv;
+	int ret, i;
+
+	mt753x_trap_frames(priv);
+
+	/* Enable and reset MIB counters */
+	mt7530_mib_reset(ds);
+
+	/* Disable flooding on all ports */
+	mt7530_clear(priv, MT7530_MFC, BC_FFP_MASK | UNM_FFP_MASK |
+		     UNU_FFP_MASK);
+
+	for (i = 0; i < MT7530_NUM_PORTS; i++) {
+		/* Disable forwarding by default on all ports */
+		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
+			   PCR_MATRIX_CLR);
+
+		/* Disable learning by default on all ports */
+		mt7530_set(priv, MT7530_PSC_P(i), SA_DIS);
+
+		mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
+
+		if (dsa_is_cpu_port(ds, i)) {
+			ret = mt753x_cpu_port_enable(ds, i);
+			if (ret)
+				return ret;
+		} else {
+			mt7530_port_disable(ds, i);
+
+			/* Set default PVID to 0 on all user ports */
+			mt7530_rmw(priv, MT7530_PPBV1_P(i), G0_PORT_VID_MASK,
+				   G0_PORT_VID_DEF);
+		}
+
+		/* Enable consistent egress tag */
+		mt7530_rmw(priv, MT7530_PVC_P(i), PVC_EG_TAG_MASK,
+			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
+	}
+
+	/* Allow mirroring frames received on the local port (monitor port). */
+	mt7530_set(priv, MT753X_AGC, LOCAL_EN);
+
+	/* Flush the FDB table */
+	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int
 mt7531_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
@@ -2261,11 +2594,11 @@
 	 */
 	if (priv->mcm) {
 		reset_control_assert(priv->rstc);
-		usleep_range(1000, 1100);
+		usleep_range(5000, 5100);
 		reset_control_deassert(priv->rstc);
 	} else {
 		gpiod_set_value_cansleep(priv->reset, 0);
-		usleep_range(1000, 1100);
+		usleep_range(5000, 5100);
 		gpiod_set_value_cansleep(priv->reset, 1);
 	}
 
@@ -2291,6 +2624,8 @@
 		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
 		     SYS_CTRL_REG_RST);
 
+	mt7531_pll_setup(priv);
+
 	if (mt7531_dual_sgmii_supported(priv)) {
 		priv->p5_intf_sel = P5_INTF_SEL_GMAC5_SGMII;
 
@@ -2312,54 +2647,27 @@
 	priv->p5_interface = PHY_INTERFACE_MODE_NA;
 	priv->p6_interface = PHY_INTERFACE_MODE_NA;
 
-	/* Enable PHY core PLL, since phy_device has not yet been created
-	 * provided for phy_[read,write]_mmd_indirect is called, we provide
-	 * our own mt7531_ind_mmd_phy_[read,write] to complete this
-	 * function.
+	/* Enable Energy-Efficient Ethernet (EEE) and PHY core PLL, since
+	 * phy_device has not yet been created provided for
+	 * phy_[read,write]_mmd_indirect is called, we provide our own
+	 * mt7531_ind_mmd_phy_[read,write] to complete this function.
 	 */
 	val = mt7531_ind_c45_phy_read(priv, MT753X_CTRL_PHY_ADDR,
 				      MDIO_MMD_VEND2, CORE_PLL_GROUP4);
-	val |= MT7531_PHY_PLL_BYPASS_MODE;
+	val |= MT7531_RG_SYSPLL_DMY2 | MT7531_PHY_PLL_BYPASS_MODE;
 	val &= ~MT7531_PHY_PLL_OFF;
 	mt7531_ind_c45_phy_write(priv, MT753X_CTRL_PHY_ADDR, MDIO_MMD_VEND2,
 				 CORE_PLL_GROUP4, val);
 
-	/* BPDU to CPU port */
-	mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
-		   BIT(MT7530_CPU_PORT));
-	mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
-		   MT753X_BPDU_CPU_ONLY);
-
-	/* Enable and reset MIB counters */
-	mt7530_mib_reset(ds);
-
-	for (i = 0; i < MT7530_NUM_PORTS; i++) {
-		/* Disable forwarding by default on all ports */
-		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
-			   PCR_MATRIX_CLR);
-
-		/* Disable learning by default on all ports */
-		mt7530_set(priv, MT7530_PSC_P(i), SA_DIS);
-
-		mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
-
-		if (dsa_is_cpu_port(ds, i)) {
-			ret = mt753x_cpu_port_enable(ds, i);
-			if (ret)
-				return ret;
-		} else {
-			mt7530_port_disable(ds, i);
-
-			/* Set default PVID to 0 on all user ports */
-			mt7530_rmw(priv, MT7530_PPBV1_P(i), G0_PORT_VID_MASK,
-				   G0_PORT_VID_DEF);
-		}
-
-		/* Enable consistent egress tag */
-		mt7530_rmw(priv, MT7530_PVC_P(i), PVC_EG_TAG_MASK,
-			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
+	/* Disable EEE advertisement on the switch PHYs. */
+	for (i = MT753X_CTRL_PHY_ADDR;
+	     i < MT753X_CTRL_PHY_ADDR + MT7530_NUM_PHYS; i++) {
+		mt7531_ind_c45_phy_write(priv, i, MDIO_MMD_AN, MDIO_AN_EEE_ADV,
+					 0);
 	}
 
+	mt7531_setup_common(ds);
+
 	/* Setup VLAN ID 0 for VLAN-unaware bridges */
 	ret = mt7530_setup_vlan0(priv);
 	if (ret)
@@ -2368,11 +2676,6 @@
 	ds->assisted_learning_on_cpu_port = true;
 	ds->mtu_enforcement_ingress = true;
 
-	/* Flush the FDB table */
-	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
-	if (ret < 0)
-		return ret;
-
 	return 0;
 }
 
@@ -2526,13 +2829,7 @@
 	/* Port5 supports ethier RGMII or SGMII.
 	 * Port6 supports SGMII only.
 	 */
-	switch (port) {
-	case 5:
-		if (mt7531_is_rgmii_port(priv, port))
-			break;
-		fallthrough;
-	case 6:
-		phylink_set(supported, 1000baseX_Full);
+	if (port == 6) {
 		phylink_set(supported, 2500baseX_Full);
 		phylink_set(supported, 2500baseT_Full);
 	}
@@ -2872,8 +3169,6 @@
 	case 6:
 		interface = PHY_INTERFACE_MODE_2500BASEX;
 
-		mt7531_pad_setup(ds, interface);
-
 		priv->p6_interface = interface;
 		break;
 	default:
@@ -2900,8 +3195,6 @@
 mt7530_mac_port_validate(struct dsa_switch *ds, int port,
 			 unsigned long *supported)
 {
-	if (port == 5)
-		phylink_set(supported, 1000baseX_Full);
 }
 
 static void mt7531_mac_port_validate(struct dsa_switch *ds, int port,
@@ -2928,7 +3221,7 @@
 
 	phylink_set_port_modes(mask);
 
-	if (state->interface != PHY_INTERFACE_MODE_TRGMII ||
+	if (state->interface != PHY_INTERFACE_MODE_TRGMII &&
 	    !phy_interface_mode_is_8023z(state->interface)) {
 		phylink_set(mask, 10baseT_Half);
 		phylink_set(mask, 10baseT_Full);
@@ -2938,8 +3231,10 @@
 	}
 
 	/* This switch only supports 1G full-duplex. */
-	if (state->interface != PHY_INTERFACE_MODE_MII)
+	if (state->interface != PHY_INTERFACE_MODE_MII) {
 		phylink_set(mask, 1000baseT_Full);
+		phylink_set(mask, 1000baseX_Full);
+	}
 
 	priv->info->mac_port_validate(ds, port, mask);
 
@@ -3108,6 +3403,7 @@
 static const struct dsa_switch_ops mt7530_switch_ops = {
 	.get_tag_protocol	= mtk_get_tag_protocol,
 	.setup			= mt753x_setup,
+	.preferred_default_local_cpu_port = mt753x_preferred_default_local_cpu_port,
 	.get_strings		= mt7530_get_strings,
 	.get_ethtool_stats	= mt7530_get_ethtool_stats,
 	.get_sset_count		= mt7530_get_sset_count,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mt7530.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mt7530.h
@@ -32,6 +32,10 @@
 #define SYSC_REG_RSTCTRL		0x34
 #define  RESET_MCM			BIT(2)
 
+/* Register for ARL global control */
+#define MT753X_AGC			0xc
+#define  LOCAL_EN			BIT(7)
+
 /* Registers to mac forward control for unknown frames */
 #define MT7530_MFC			0x10
 #define  BC_FFP(x)			(((x) & 0xff) << 24)
@@ -54,6 +58,7 @@
 #define  MT7531_MIRROR_PORT_GET(x)	(((x) >> 16) & MIRROR_MASK)
 #define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
 #define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)
+#define  MT7531_CPU_PMAP(x)		FIELD_PREP(MT7531_CPU_PMAP_MASK, x)
 
 #define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
 					 MT7531_CFC : MT7530_MFC)
@@ -64,8 +69,39 @@
 
 /* Registers for BPDU and PAE frame control*/
 #define MT753X_BPC			0x24
+#define  MT753X_PAE_BPDU_FR		BIT(25)
+#define  MT753X_PAE_EG_TAG_MASK		GENMASK(24, 22)
+#define  MT753X_PAE_EG_TAG(x)		FIELD_PREP(MT753X_PAE_EG_TAG_MASK, x)
+#define  MT753X_PAE_PORT_FW_MASK	GENMASK(18, 16)
+#define  MT753X_PAE_PORT_FW(x)		FIELD_PREP(MT753X_PAE_PORT_FW_MASK, x)
+#define  MT753X_BPDU_EG_TAG_MASK	GENMASK(8, 6)
+#define  MT753X_BPDU_EG_TAG(x)		FIELD_PREP(MT753X_BPDU_EG_TAG_MASK, x)
 #define  MT753X_BPDU_PORT_FW_MASK	GENMASK(2, 0)
 
+/* Register for :01 and :02 MAC DA frame control */
+#define MT753X_RGAC1			0x28
+#define  MT753X_R02_BPDU_FR		BIT(25)
+#define  MT753X_R02_EG_TAG_MASK		GENMASK(24, 22)
+#define  MT753X_R02_EG_TAG(x)		FIELD_PREP(MT753X_R02_EG_TAG_MASK, x)
+#define  MT753X_R02_PORT_FW_MASK	GENMASK(18, 16)
+#define  MT753X_R02_PORT_FW(x)		FIELD_PREP(MT753X_R02_PORT_FW_MASK, x)
+#define  MT753X_R01_BPDU_FR		BIT(9)
+#define  MT753X_R01_EG_TAG_MASK		GENMASK(8, 6)
+#define  MT753X_R01_EG_TAG(x)		FIELD_PREP(MT753X_R01_EG_TAG_MASK, x)
+#define  MT753X_R01_PORT_FW_MASK	GENMASK(2, 0)
+
+/* Register for :03 and :0E MAC DA frame control */
+#define MT753X_RGAC2			0x2c
+#define  MT753X_R0E_BPDU_FR		BIT(25)
+#define  MT753X_R0E_EG_TAG_MASK		GENMASK(24, 22)
+#define  MT753X_R0E_EG_TAG(x)		FIELD_PREP(MT753X_R0E_EG_TAG_MASK, x)
+#define  MT753X_R0E_PORT_FW_MASK	GENMASK(18, 16)
+#define  MT753X_R0E_PORT_FW(x)		FIELD_PREP(MT753X_R0E_PORT_FW_MASK, x)
+#define  MT753X_R03_BPDU_FR		BIT(9)
+#define  MT753X_R03_EG_TAG_MASK		GENMASK(8, 6)
+#define  MT753X_R03_EG_TAG(x)		FIELD_PREP(MT753X_R03_EG_TAG_MASK, x)
+#define  MT753X_R03_PORT_FW_MASK	GENMASK(2, 0)
+
 enum mt753x_bpdu_port_fw {
 	MT753X_BPDU_FOLLOW_MFC,
 	MT753X_BPDU_CPU_EXCLUDE = 4,
@@ -245,6 +281,7 @@
 enum mt7530_vlan_port_eg_tag {
 	MT7530_VLAN_EG_DISABLED = 0,
 	MT7530_VLAN_EG_CONSISTENT = 1,
+	MT7530_VLAN_EG_UNTAGGED = 4,
 };
 
 enum mt7530_vlan_port_attr {
@@ -636,6 +673,7 @@
 #define  RG_SYSPLL_DDSFBK_EN		BIT(12)
 #define  RG_SYSPLL_BIAS_EN		BIT(11)
 #define  RG_SYSPLL_BIAS_LPF_EN		BIT(10)
+#define  MT7531_RG_SYSPLL_DMY2		BIT(6)
 #define  MT7531_PHY_PLL_OFF		BIT(5)
 #define  MT7531_PHY_PLL_BYPASS_MODE	BIT(4)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6060.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6060.c
@@ -118,6 +118,9 @@
 	int addr = REG_PORT(p);
 	int ret;
 
+	if (dsa_is_unused_port(priv->ds, p))
+		return 0;
+
 	/* Do not force flow control, disable Ingress and Egress
 	 * Header tagging, disable VLAN tunneling, and set the port
 	 * state to Forwarding.  Additionally, if this is the CPU
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/Kconfig
@@ -2,7 +2,6 @@
 config NET_DSA_MV88E6XXX
 	tristate "Marvell 88E6xxx Ethernet switch fabric support"
 	depends on NET_DSA
-	depends on PTP_1588_CLOCK_OPTIONAL
 	select IRQ_DOMAIN
 	select NET_DSA_TAG_EDSA
 	select NET_DSA_TAG_DSA
@@ -13,7 +12,8 @@
 config NET_DSA_MV88E6XXX_PTP
 	bool "PTP support for Marvell 88E6xxx"
 	default n
-	depends on NET_DSA_MV88E6XXX && PTP_1588_CLOCK
+	depends on (NET_DSA_MV88E6XXX = y && PTP_1588_CLOCK = y) || \
+	           (NET_DSA_MV88E6XXX = m && PTP_1588_CLOCK)
 	help
 	  Say Y to enable PTP hardware timestamping on Marvell 88E6xxx switch
 	  chips that support it.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/Makefile
@@ -15,3 +15,7 @@
 mv88e6xxx-$(CONFIG_NET_DSA_MV88E6XXX_PTP) += ptp.o
 mv88e6xxx-objs += serdes.o
 mv88e6xxx-objs += smi.o
+mv88e6xxx-objs += trace.o
+
+# for tracing framework to find trace.h
+CFLAGS_trace.o := -I$(src)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/chip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/chip.c
@@ -117,8 +117,8 @@
 {
 	struct mv88e6xxx_mdio_bus *mdio_bus;
 
-	mdio_bus = list_first_entry(&chip->mdios, struct mv88e6xxx_mdio_bus,
-				    list);
+	mdio_bus = list_first_entry_or_null(&chip->mdios,
+					    struct mv88e6xxx_mdio_bus, list);
 	if (!mdio_bus)
 		return NULL;
 
@@ -471,6 +471,12 @@
 	u16 reg;
 	int err;
 
+	/* The 88e6250 family does not have the PHY detect bit. Instead,
+	 * report whether the port is internal.
+	 */
+	if (chip->info->family == MV88E6XXX_FAMILY_6250)
+		return port < chip->info->num_internal_phys;
+
 	err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_STS, &reg);
 	if (err) {
 		dev_err(chip->dev,
@@ -640,7 +646,10 @@
 					unsigned long *mask,
 					struct phylink_link_state *state)
 {
-	if (port == 0 || port == 9 || port == 10) {
+	bool is_6191x =
+		chip->info->prod_num == MV88E6XXX_PORT_SWITCH_ID_PROD_6191X;
+
+	if (((port == 0 || port == 9) && !is_6191x) || port == 10) {
 		phylink_set(mask, 10000baseT_Full);
 		phylink_set(mask, 10000baseKR_Full);
 		phylink_set(mask, 10000baseCR_Full);
@@ -690,44 +699,48 @@
 {
 	struct mv88e6xxx_chip *chip = ds->priv;
 	struct mv88e6xxx_port *p;
-	int err;
+	int err = 0;
 
 	p = &chip->ports[port];
 
-	/* FIXME: is this the correct test? If we're in fixed mode on an
-	 * internal port, why should we process this any different from
-	 * PHY mode? On the other hand, the port may be automedia between
-	 * an internal PHY and the serdes...
-	 */
-	if ((mode == MLO_AN_PHY) && mv88e6xxx_phy_is_internal(ds, port))
-		return;
-
 	mv88e6xxx_reg_lock(chip);
-	/* In inband mode, the link may come up at any time while the link
-	 * is not forced down. Force the link down while we reconfigure the
-	 * interface mode.
-	 */
-	if (mode == MLO_AN_INBAND && p->interface != state->interface &&
-	    chip->info->ops->port_set_link)
-		chip->info->ops->port_set_link(chip, port, LINK_FORCED_DOWN);
 
-	err = mv88e6xxx_port_config_interface(chip, port, state->interface);
-	if (err && err != -EOPNOTSUPP)
-		goto err_unlock;
+	if (mode != MLO_AN_PHY || !mv88e6xxx_phy_is_internal(ds, port)) {
+		/* In inband mode, the link may come up at any time while the
+		 * link is not forced down. Force the link down while we
+		 * reconfigure the interface mode.
+		 */
+		if (mode == MLO_AN_INBAND &&
+		    p->interface != state->interface &&
+		    chip->info->ops->port_set_link)
+			chip->info->ops->port_set_link(chip, port,
+						       LINK_FORCED_DOWN);
 
-	err = mv88e6xxx_serdes_pcs_config(chip, port, mode, state->interface,
-					  state->advertising);
-	/* FIXME: we should restart negotiation if something changed - which
-	 * is something we get if we convert to using phylinks PCS operations.
-	 */
-	if (err > 0)
-		err = 0;
+		err = mv88e6xxx_port_config_interface(chip, port,
+						      state->interface);
+		if (err && err != -EOPNOTSUPP)
+			goto err_unlock;
+
+		err = mv88e6xxx_serdes_pcs_config(chip, port, mode,
+						  state->interface,
+						  state->advertising);
+		/* FIXME: we should restart negotiation if something changed -
+		 * which is something we get if we convert to using phylinks
+		 * PCS operations.
+		 */
+		if (err > 0)
+			err = 0;
+	}
 
 	/* Undo the forced down state above after completing configuration
-	 * irrespective of its state on entry, which allows the link to come up.
+	 * irrespective of its state on entry, which allows the link to come
+	 * up in the in-band case where there is no separate SERDES. Also
+	 * ensure that the link can come up if the PPU is in use and we are
+	 * in PHY mode (we treat the PPU as an effective in-band mechanism.)
 	 */
-	if (mode == MLO_AN_INBAND && p->interface != state->interface &&
-	    chip->info->ops->port_set_link)
+	if (chip->info->ops->port_set_link &&
+	    ((mode == MLO_AN_INBAND && p->interface != state->interface) ||
+	     (mode == MLO_AN_PHY && mv88e6xxx_port_ppu_updates(chip, port))))
 		chip->info->ops->port_set_link(chip, port, LINK_UNFORCED);
 
 	p->interface = state->interface;
@@ -750,13 +763,16 @@
 	ops = chip->info->ops;
 
 	mv88e6xxx_reg_lock(chip);
-	/* Internal PHYs propagate their configuration directly to the MAC.
-	 * External PHYs depend on whether the PPU is enabled for this port.
+	/* Force the link down if we know the port may not be automatically
+	 * updated by the switch or if we are using fixed-link mode.
 	 */
-	if (((!mv88e6xxx_phy_is_internal(ds, port) &&
-	      !mv88e6xxx_port_ppu_updates(chip, port)) ||
+	if ((!mv88e6xxx_port_ppu_updates(chip, port) ||
 	     mode == MLO_AN_FIXED) && ops->port_sync_link)
 		err = ops->port_sync_link(chip, port, mode, false);
+
+	if (!err && ops->port_set_speed_duplex)
+		err = ops->port_set_speed_duplex(chip, port, SPEED_UNFORCED,
+						 DUPLEX_UNFORCED);
 	mv88e6xxx_reg_unlock(chip);
 
 	if (err)
@@ -777,11 +793,11 @@
 	ops = chip->info->ops;
 
 	mv88e6xxx_reg_lock(chip);
-	/* Internal PHYs propagate their configuration directly to the MAC.
-	 * External PHYs depend on whether the PPU is enabled for this port.
+	/* Configure and force the link up if we know that the port may not
+	 * automatically updated by the switch or if we are using fixed-link
+	 * mode.
 	 */
-	if ((!mv88e6xxx_phy_is_internal(ds, port) &&
-	     !mv88e6xxx_port_ppu_updates(chip, port)) ||
+	if (!mv88e6xxx_port_ppu_updates(chip, port) ||
 	    mode == MLO_AN_FIXED) {
 		/* FIXME: for an automedia port, should we force the link
 		 * down here - what if the link comes up due to "other" media
@@ -1759,13 +1775,11 @@
 	return err;
 }
 
-static int mv88e6xxx_port_db_load_purge(struct mv88e6xxx_chip *chip, int port,
-					const unsigned char *addr, u16 vid,
-					u8 state)
+static int mv88e6xxx_port_db_get(struct mv88e6xxx_chip *chip,
+				 const unsigned char *addr, u16 vid,
+				 u16 *fid, struct mv88e6xxx_atu_entry *entry)
 {
-	struct mv88e6xxx_atu_entry entry;
 	struct mv88e6xxx_vtu_entry vlan;
-	u16 fid;
 	int err;
 
 	/* Ports have two private address databases: one for when the port is
@@ -1776,7 +1790,7 @@
 	 * VLAN ID into the port's database used for VLAN-unaware bridging.
 	 */
 	if (vid == 0) {
-		fid = MV88E6XXX_FID_BRIDGED;
+		*fid = MV88E6XXX_FID_BRIDGED;
 	} else {
 		err = mv88e6xxx_vtu_get(chip, vid, &vlan);
 		if (err)
@@ -1786,14 +1800,39 @@
 		if (!vlan.valid)
 			return -EOPNOTSUPP;
 
-		fid = vlan.fid;
+		*fid = vlan.fid;
 	}
 
-	entry.state = 0;
-	ether_addr_copy(entry.mac, addr);
-	eth_addr_dec(entry.mac);
+	entry->state = 0;
+	ether_addr_copy(entry->mac, addr);
+	eth_addr_dec(entry->mac);
+
+	return mv88e6xxx_g1_atu_getnext(chip, *fid, entry);
+}
+
+static bool mv88e6xxx_port_db_find(struct mv88e6xxx_chip *chip,
+				   const unsigned char *addr, u16 vid)
+{
+	struct mv88e6xxx_atu_entry entry;
+	u16 fid;
+	int err;
+
+	err = mv88e6xxx_port_db_get(chip, addr, vid, &fid, &entry);
+	if (err)
+		return false;
+
+	return entry.state && ether_addr_equal(entry.mac, addr);
+}
+
+static int mv88e6xxx_port_db_load_purge(struct mv88e6xxx_chip *chip, int port,
+					const unsigned char *addr, u16 vid,
+					u8 state)
+{
+	struct mv88e6xxx_atu_entry entry;
+	u16 fid;
+	int err;
 
-	err = mv88e6xxx_g1_atu_getnext(chip, fid, &entry);
+	err = mv88e6xxx_port_db_get(chip, addr, vid, &fid, &entry);
 	if (err)
 		return err;
 
@@ -2308,6 +2347,13 @@
 	mv88e6xxx_reg_lock(chip);
 	err = mv88e6xxx_port_db_load_purge(chip, port, addr, vid,
 					   MV88E6XXX_G1_ATU_DATA_STATE_UC_STATIC);
+	if (err)
+		goto out;
+
+	if (!mv88e6xxx_port_db_find(chip, addr, vid))
+		err = -ENOSPC;
+
+out:
 	mv88e6xxx_reg_unlock(chip);
 
 	return err;
@@ -2569,15 +2615,35 @@
 static void mv88e6xxx_hardware_reset(struct mv88e6xxx_chip *chip)
 {
 	struct gpio_desc *gpiod = chip->reset;
+	int err;
 
 	/* If there is a GPIO connected to the reset pin, toggle it */
 	if (gpiod) {
+		/* If the switch has just been reset and not yet completed
+		 * loading EEPROM, the reset may interrupt the I2C transaction
+		 * mid-byte, causing the first EEPROM read after the reset
+		 * from the wrong location resulting in the switch booting
+		 * to wrong mode and inoperable.
+		 * For this reason, switch families with EEPROM support
+		 * generally wait for EEPROM loads to complete as their pre-
+		 * and post-reset handlers.
+		 */
+		if (chip->info->ops->hardware_reset_pre) {
+			err = chip->info->ops->hardware_reset_pre(chip);
+			if (err)
+				dev_err(chip->dev, "pre-reset error: %d\n", err);
+		}
+
 		gpiod_set_value_cansleep(gpiod, 1);
 		usleep_range(10000, 20000);
 		gpiod_set_value_cansleep(gpiod, 0);
 		usleep_range(10000, 20000);
 
-		mv88e6xxx_g1_wait_eeprom_done(chip);
+		if (chip->info->ops->hardware_reset_post) {
+			err = chip->info->ops->hardware_reset_post(chip);
+			if (err)
+				dev_err(chip->dev, "post-reset error: %d\n", err);
+		}
 	}
 }
 
@@ -2896,9 +2962,14 @@
 	 * If this is the upstream port for this switch, enable
 	 * forwarding of unknown unicasts and multicasts.
 	 */
-	reg = MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP |
-		MV88E6185_PORT_CTL0_USE_TAG | MV88E6185_PORT_CTL0_USE_IP |
+	reg = MV88E6185_PORT_CTL0_USE_TAG | MV88E6185_PORT_CTL0_USE_IP |
 		MV88E6XXX_PORT_CTL0_STATE_FORWARDING;
+	/* Forward any IPv4 IGMP or IPv6 MLD frames received
+	 * by a USER port to the CPU port to allow snooping.
+	 */
+	if (dsa_is_user_port(ds, port))
+		reg |= MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP;
+
 	err = mv88e6xxx_port_write(chip, port, MV88E6XXX_PORT_CTL0, reg);
 	if (err)
 		return err;
@@ -3038,7 +3109,7 @@
 		return 10240 - VLAN_ETH_HLEN - EDSA_HLEN - ETH_FCS_LEN;
 	else if (chip->info->ops->set_max_frame_size)
 		return 1632 - VLAN_ETH_HLEN - EDSA_HLEN - ETH_FCS_LEN;
-	return 1522 - VLAN_ETH_HLEN - EDSA_HLEN - ETH_FCS_LEN;
+	return ETH_DATA_LEN;
 }
 
 static int mv88e6xxx_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
@@ -3046,17 +3117,26 @@
 	struct mv88e6xxx_chip *chip = ds->priv;
 	int ret = 0;
 
+	/* For families where we don't know how to alter the MTU,
+	 * just accept any value up to ETH_DATA_LEN
+	 */
+	if (!chip->info->ops->port_set_jumbo_size &&
+	    !chip->info->ops->set_max_frame_size) {
+		if (new_mtu > ETH_DATA_LEN)
+			return -EINVAL;
+
+		return 0;
+	}
+
 	if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port))
 		new_mtu += EDSA_HLEN;
 
 	mv88e6xxx_reg_lock(chip);
 	if (chip->info->ops->port_set_jumbo_size)
 		ret = chip->info->ops->port_set_jumbo_size(chip, port, new_mtu);
-	else if (chip->info->ops->set_max_frame_size)
+	else if (chip->info->ops->set_max_frame_size &&
+		 dsa_is_cpu_port(ds, port))
 		ret = chip->info->ops->set_max_frame_size(chip, new_mtu);
-	else
-		if (new_mtu > 1522)
-			ret = -EINVAL;
 	mv88e6xxx_reg_unlock(chip);
 
 	return ret;
@@ -3400,7 +3480,7 @@
 			return err;
 	}
 
-	bus = devm_mdiobus_alloc_size(chip->dev, sizeof(*mdio_bus));
+	bus = mdiobus_alloc_size(sizeof(*mdio_bus));
 	if (!bus)
 		return -ENOMEM;
 
@@ -3425,14 +3505,14 @@
 	if (!external) {
 		err = mv88e6xxx_g2_irq_mdio_setup(chip, bus);
 		if (err)
-			return err;
+			goto out;
 	}
 
 	err = of_mdiobus_register(bus, np);
 	if (err) {
 		dev_err(chip->dev, "Cannot register MDIO bus (%d)\n", err);
 		mv88e6xxx_g2_irq_mdio_free(chip, bus);
-		return err;
+		goto out;
 	}
 
 	if (external)
@@ -3441,21 +3521,26 @@
 		list_add(&mdio_bus->list, &chip->mdios);
 
 	return 0;
+
+out:
+	mdiobus_free(bus);
+	return err;
 }
 
 static void mv88e6xxx_mdios_unregister(struct mv88e6xxx_chip *chip)
 
 {
-	struct mv88e6xxx_mdio_bus *mdio_bus;
+	struct mv88e6xxx_mdio_bus *mdio_bus, *p;
 	struct mii_bus *bus;
 
-	list_for_each_entry(mdio_bus, &chip->mdios, list) {
+	list_for_each_entry_safe(mdio_bus, p, &chip->mdios, list) {
 		bus = mdio_bus->bus;
 
 		if (!mdio_bus->external)
 			mv88e6xxx_g2_irq_mdio_free(chip, bus);
 
 		mdiobus_unregister(bus);
+		mdiobus_free(bus);
 	}
 }
 
@@ -3471,6 +3556,7 @@
 	 */
 	child = of_get_child_by_name(np, "mdio");
 	err = mv88e6xxx_mdio_register(chip, child, false);
+	of_node_put(child);
 	if (err)
 		return err;
 
@@ -3628,6 +3714,7 @@
 	.port_sync_link = mv88e6185_port_sync_link,
 	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
+	.port_set_policy = mv88e6352_port_set_policy,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_ucast_flood = mv88e6352_port_set_ucast_flood,
 	.port_set_mcast_flood = mv88e6352_port_set_mcast_flood,
@@ -3778,6 +3865,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu =  mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -3960,6 +4049,8 @@
 	.watchdog_ops = &mv88e6097_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6352_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4057,6 +4148,8 @@
 	.watchdog_ops = &mv88e6097_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6352_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4155,6 +4248,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4216,6 +4311,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4275,6 +4372,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4337,6 +4436,8 @@
 	.watchdog_ops = &mv88e6097_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6352_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4392,6 +4493,8 @@
 	.watchdog_ops = &mv88e6250_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6250_g1_wait_eeprom_done_prereset,
+	.hardware_reset_post = mv88e6xxx_g1_wait_eeprom_done,
 	.reset = mv88e6250_g1_reset,
 	.vtu_getnext = mv88e6185_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6185_g1_vtu_loadpurge,
@@ -4436,6 +4539,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4497,6 +4602,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.vtu_getnext = mv88e6185_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6185_g1_vtu_loadpurge,
@@ -4539,6 +4646,9 @@
 	.set_cpu_port = mv88e6095_g1_set_cpu_port,
 	.set_egress_port = mv88e6095_g1_set_egress_port,
 	.watchdog_ops = &mv88e6390_watchdog_ops,
+	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.vtu_getnext = mv88e6185_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6185_g1_vtu_loadpurge,
@@ -4587,6 +4697,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu =  mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4737,6 +4849,8 @@
 	.watchdog_ops = &mv88e6097_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6352_g2_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6352_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4801,6 +4915,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4866,6 +4982,8 @@
 	.watchdog_ops = &mv88e6390_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6390_g1_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -4931,9 +5049,11 @@
 	 * .port_set_upstream_port method.
 	 */
 	.set_egress_port = mv88e6393x_set_egress_port,
-	.watchdog_ops = &mv88e6390_watchdog_ops,
+	.watchdog_ops = &mv88e6393x_watchdog_ops,
 	.mgmt_rsvd2cpu = mv88e6393x_port_mgmt_rsvd2cpu,
 	.pot_clear = mv88e6xxx_g2_pot_clear,
+	.hardware_reset_pre = mv88e6xxx_g2_eeprom_wait,
+	.hardware_reset_post = mv88e6xxx_g2_eeprom_wait,
 	.reset = mv88e6352_g1_reset,
 	.rmu_disable = mv88e6390_g1_rmu_disable,
 	.atu_get_hash = mv88e6165_g1_atu_get_hash,
@@ -5069,7 +5189,7 @@
 		.prod_num = MV88E6XXX_PORT_SWITCH_ID_PROD_6141,
 		.family = MV88E6XXX_FAMILY_6341,
 		.name = "Marvell 88E6141",
-		.num_databases = 4096,
+		.num_databases = 256,
 		.num_macs = 2048,
 		.num_ports = 6,
 		.num_internal_phys = 5,
@@ -5512,7 +5632,7 @@
 		.prod_num = MV88E6XXX_PORT_SWITCH_ID_PROD_6341,
 		.family = MV88E6XXX_FAMILY_6341,
 		.name = "Marvell 88E6341",
-		.num_databases = 4096,
+		.num_databases = 256,
 		.num_macs = 2048,
 		.num_internal_phys = 5,
 		.num_ports = 6,
@@ -5788,6 +5908,13 @@
 	mv88e6xxx_reg_lock(chip);
 	err = mv88e6xxx_port_db_load_purge(chip, port, mdb->addr, mdb->vid,
 					   MV88E6XXX_G1_ATU_DATA_STATE_MC_STATIC);
+	if (err)
+		goto out;
+
+	if (!mv88e6xxx_port_db_find(chip, mdb->addr, mdb->vid))
+		err = -ENOSPC;
+
+out:
 	mv88e6xxx_reg_unlock(chip);
 
 	return err;
@@ -6395,7 +6522,7 @@
 		goto out;
 	}
 	if (chip->reset)
-		usleep_range(1000, 2000);
+		usleep_range(10000, 20000);
 
 	err = mv88e6xxx_detect(chip);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/chip.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/chip.h
@@ -434,6 +434,12 @@
 	int (*ppu_enable)(struct mv88e6xxx_chip *chip);
 	int (*ppu_disable)(struct mv88e6xxx_chip *chip);
 
+	/* Additional handlers to run before and after hard reset, to make sure
+	 * that the switch and EEPROM are in a good state.
+	 */
+	int (*hardware_reset_pre)(struct mv88e6xxx_chip *chip);
+	int (*hardware_reset_post)(struct mv88e6xxx_chip *chip);
+
 	/* Switch Software Reset */
 	int (*reset)(struct mv88e6xxx_chip *chip);
 
@@ -578,8 +584,8 @@
 	int (*serdes_get_sset_count)(struct mv88e6xxx_chip *chip, int port);
 	int (*serdes_get_strings)(struct mv88e6xxx_chip *chip,  int port,
 				  uint8_t *data);
-	int (*serdes_get_stats)(struct mv88e6xxx_chip *chip,  int port,
-				uint64_t *data);
+	size_t (*serdes_get_stats)(struct mv88e6xxx_chip *chip, int port,
+				   uint64_t *data);
 
 	/* SERDES registers for ethtool */
 	int (*serdes_get_regs_len)(struct mv88e6xxx_chip *chip,  int port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/global1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/global1.c
@@ -75,35 +75,93 @@
 	return mv88e6xxx_g1_wait_bit(chip, MV88E6XXX_G1_STS, bit, 1);
 }
 
-void mv88e6xxx_g1_wait_eeprom_done(struct mv88e6xxx_chip *chip)
+static int mv88e6250_g1_eeprom_reload(struct mv88e6xxx_chip *chip)
 {
-	const unsigned long timeout = jiffies + 1 * HZ;
+	/* MV88E6185_G1_CTL1_RELOAD_EEPROM is also valid for 88E6250 */
+	int bit = __bf_shf(MV88E6185_G1_CTL1_RELOAD_EEPROM);
 	u16 val;
 	int err;
 
+	err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_CTL1, &val);
+	if (err)
+		return err;
+
+	val |= MV88E6185_G1_CTL1_RELOAD_EEPROM;
+
+	err = mv88e6xxx_g1_write(chip, MV88E6XXX_G1_CTL1, val);
+	if (err)
+		return err;
+
+	return mv88e6xxx_g1_wait_bit(chip, MV88E6XXX_G1_CTL1, bit, 0);
+}
+
+/* Returns 0 when done, -EBUSY when waiting, other negative codes on error */
+static int mv88e6xxx_g1_is_eeprom_done(struct mv88e6xxx_chip *chip)
+{
+	u16 val;
+	int err;
+
+	err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_STS, &val);
+	if (err < 0) {
+		dev_err(chip->dev, "Error reading status");
+		return err;
+	}
+
+	/* If the switch is still resetting, it may not
+	 * respond on the bus, and so MDIO read returns
+	 * 0xffff. Differentiate between that, and waiting for
+	 * the EEPROM to be done by bit 0 being set.
+	 */
+	if (val == 0xffff || !(val & BIT(MV88E6XXX_G1_STS_IRQ_EEPROM_DONE)))
+		return -EBUSY;
+
+	return 0;
+}
+
+/* As the EEInt (EEPROM done) flag clears on read if the status register, this
+ * function must be called directly after a hard reset or EEPROM ReLoad request,
+ * or the done condition may have been missed
+ */
+int mv88e6xxx_g1_wait_eeprom_done(struct mv88e6xxx_chip *chip)
+{
+	const unsigned long timeout = jiffies + 1 * HZ;
+	int ret;
+
 	/* Wait up to 1 second for the switch to finish reading the
 	 * EEPROM.
 	 */
 	while (time_before(jiffies, timeout)) {
-		err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_STS, &val);
-		if (err) {
-			dev_err(chip->dev, "Error reading status");
-			return;
-		}
-
-		/* If the switch is still resetting, it may not
-		 * respond on the bus, and so MDIO read returns
-		 * 0xffff. Differentiate between that, and waiting for
-		 * the EEPROM to be done by bit 0 being set.
-		 */
-		if (val != 0xffff &&
-		    val & BIT(MV88E6XXX_G1_STS_IRQ_EEPROM_DONE))
-			return;
-
-		usleep_range(1000, 2000);
+		ret = mv88e6xxx_g1_is_eeprom_done(chip);
+		if (ret != -EBUSY)
+			return ret;
 	}
 
 	dev_err(chip->dev, "Timeout waiting for EEPROM done");
+	return -ETIMEDOUT;
+}
+
+int mv88e6250_g1_wait_eeprom_done_prereset(struct mv88e6xxx_chip *chip)
+{
+	int ret;
+
+	ret = mv88e6xxx_g1_is_eeprom_done(chip);
+	if (ret != -EBUSY)
+		return ret;
+
+	/* Pre-reset, we don't know the state of the switch - when
+	 * mv88e6xxx_g1_is_eeprom_done() returns -EBUSY, that may be because
+	 * the switch is actually busy reading the EEPROM, or because
+	 * MV88E6XXX_G1_STS_IRQ_EEPROM_DONE has been cleared by an unrelated
+	 * status register read already.
+	 *
+	 * To account for the latter case, trigger another EEPROM reload for
+	 * another chance at seeing the done flag.
+	 */
+	ret = mv88e6250_g1_eeprom_reload(chip);
+	if (ret)
+		return ret;
+
+	return mv88e6xxx_g1_wait_eeprom_done(chip);
 }
 
 /* Offset 0x01: Switch MAC Address Register Bytes 0 & 1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/global1.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/global1.h
@@ -280,7 +280,8 @@
 int mv88e6185_g1_reset(struct mv88e6xxx_chip *chip);
 int mv88e6352_g1_reset(struct mv88e6xxx_chip *chip);
 int mv88e6250_g1_reset(struct mv88e6xxx_chip *chip);
-void mv88e6xxx_g1_wait_eeprom_done(struct mv88e6xxx_chip *chip);
+int mv88e6xxx_g1_wait_eeprom_done(struct mv88e6xxx_chip *chip);
+int mv88e6250_g1_wait_eeprom_done_prereset(struct mv88e6xxx_chip *chip);
 
 int mv88e6185_g1_ppu_enable(struct mv88e6xxx_chip *chip);
 int mv88e6185_g1_ppu_disable(struct mv88e6xxx_chip *chip);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/global1_atu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/global1_atu.c
@@ -12,6 +12,7 @@
 
 #include "chip.h"
 #include "global1.h"
+#include "trace.h"
 
 /* Offset 0x01: ATU FID Register */
 
@@ -114,6 +115,19 @@
 	return mv88e6xxx_g1_wait_bit(chip, MV88E6XXX_G1_ATU_OP, bit, 0);
 }
 
+static int mv88e6xxx_g1_read_atu_violation(struct mv88e6xxx_chip *chip)
+{
+	int err;
+
+	err = mv88e6xxx_g1_write(chip, MV88E6XXX_G1_ATU_OP,
+				 MV88E6XXX_G1_ATU_OP_BUSY |
+				 MV88E6XXX_G1_ATU_OP_GET_CLR_VIOLATION);
+	if (err)
+		return err;
+
+	return mv88e6xxx_g1_atu_op_wait(chip);
+}
+
 static int mv88e6xxx_g1_atu_op(struct mv88e6xxx_chip *chip, u16 fid, u16 op)
 {
 	u16 val;
@@ -159,6 +173,41 @@
 	return mv88e6xxx_g1_atu_op(chip, fid, MV88E6XXX_G1_ATU_OP_GET_NEXT_DB);
 }
 
+static int mv88e6xxx_g1_atu_fid_read(struct mv88e6xxx_chip *chip, u16 *fid)
+{
+	u16 val = 0, upper = 0, op = 0;
+	int err = -EOPNOTSUPP;
+
+	if (mv88e6xxx_num_databases(chip) > 256) {
+		err = mv88e6xxx_g1_read(chip, MV88E6352_G1_ATU_FID, &val);
+		val &= 0xfff;
+		if (err)
+			return err;
+	} else {
+		err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_ATU_OP, &op);
+		if (err)
+			return err;
+		if (mv88e6xxx_num_databases(chip) > 64) {
+			/* ATU DBNum[7:4] are located in ATU Control 15:12 */
+			err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_ATU_CTL,
+						&upper);
+			if (err)
+				return err;
+
+			upper = (upper >> 8) & 0x00f0;
+		} else if (mv88e6xxx_num_databases(chip) > 16) {
+			/* ATU DBNum[5:4] are located in ATU Operation 9:8 */
+			upper = (op >> 4) & 0x30;
+		}
+
+		/* ATU DBNum[3:0] are located in ATU Operation 3:0 */
+		val = (op & 0xf) | upper;
+	}
+	*fid = val;
+
+	return err;
+}
+
 /* Offset 0x0C: ATU Data Register */
 
 static int mv88e6xxx_g1_atu_data_read(struct mv88e6xxx_chip *chip,
@@ -353,14 +402,12 @@
 {
 	struct mv88e6xxx_chip *chip = dev_id;
 	struct mv88e6xxx_atu_entry entry;
-	int spid;
-	int err;
-	u16 val;
+	int err, spid;
+	u16 val, fid;
 
 	mv88e6xxx_reg_lock(chip);
 
-	err = mv88e6xxx_g1_atu_op(chip, 0,
-				  MV88E6XXX_G1_ATU_OP_GET_CLR_VIOLATION);
+	err = mv88e6xxx_g1_read_atu_violation(chip);
 	if (err)
 		goto out;
 
@@ -368,6 +415,10 @@
 	if (err)
 		goto out;
 
+	err = mv88e6xxx_g1_atu_fid_read(chip, &fid);
+	if (err)
+		goto out;
+
 	err = mv88e6xxx_g1_atu_data_read(chip, &entry);
 	if (err)
 		goto out;
@@ -385,24 +436,25 @@
 	}
 
 	if (val & MV88E6XXX_G1_ATU_OP_MEMBER_VIOLATION) {
-		dev_err_ratelimited(chip->dev,
-				    "ATU member violation for %pM portvec %x spid %d\n",
-				    entry.mac, entry.portvec, spid);
+		trace_mv88e6xxx_atu_member_violation(chip->dev, spid,
+						     entry.portvec, entry.mac,
+						     fid);
 		chip->ports[spid].atu_member_violation++;
 	}
 
 	if (val & MV88E6XXX_G1_ATU_OP_MISS_VIOLATION) {
-		dev_err_ratelimited(chip->dev,
-				    "ATU miss violation for %pM portvec %x spid %d\n",
-				    entry.mac, entry.portvec, spid);
+		trace_mv88e6xxx_atu_miss_violation(chip->dev, spid,
+						   entry.portvec, entry.mac,
+						   fid);
 		chip->ports[spid].atu_miss_violation++;
 	}
 
 	if (val & MV88E6XXX_G1_ATU_OP_FULL_VIOLATION) {
-		dev_err_ratelimited(chip->dev,
-				    "ATU full violation for %pM portvec %x spid %d\n",
-				    entry.mac, entry.portvec, spid);
-		chip->ports[spid].atu_full_violation++;
+		trace_mv88e6xxx_atu_full_violation(chip->dev, spid,
+						   entry.portvec, entry.mac,
+						   fid);
+		if (spid < ARRAY_SIZE(chip->ports))
+			chip->ports[spid].atu_full_violation++;
 	}
 	mv88e6xxx_reg_unlock(chip);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/global2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/global2.c
@@ -340,7 +340,7 @@
  * Offset 0x15: EEPROM Addr (for 8-bit data access)
  */
 
-static int mv88e6xxx_g2_eeprom_wait(struct mv88e6xxx_chip *chip)
+int mv88e6xxx_g2_eeprom_wait(struct mv88e6xxx_chip *chip)
 {
 	int bit = __bf_shf(MV88E6XXX_G2_EEPROM_CMD_BUSY);
 	int err;
@@ -930,6 +930,26 @@
 	.irq_setup = mv88e6390_watchdog_setup,
 	.irq_free = mv88e6390_watchdog_free,
 };
+
+static int mv88e6393x_watchdog_action(struct mv88e6xxx_chip *chip, int irq)
+{
+	mv88e6390_watchdog_action(chip, irq);
+
+	/* Fix for clearing the force WD event bit.
+	 * Unreleased erratum on mv88e6393x.
+	 */
+	mv88e6xxx_g2_write(chip, MV88E6390_G2_WDOG_CTL,
+			   MV88E6390_G2_WDOG_CTL_UPDATE |
+			   MV88E6390_G2_WDOG_CTL_PTR_EVENT);
+
+	return IRQ_HANDLED;
+}
+
+const struct mv88e6xxx_irq_ops mv88e6393x_watchdog_ops = {
+	.irq_action = mv88e6393x_watchdog_action,
+	.irq_setup = mv88e6390_watchdog_setup,
+	.irq_free = mv88e6390_watchdog_free,
+};
 
 static irqreturn_t mv88e6xxx_g2_watchdog_thread_fn(int irq, void *dev_id)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/global2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/global2.h
@@ -357,10 +357,12 @@
 
 int mv88e6xxx_g2_device_mapping_write(struct mv88e6xxx_chip *chip, int target,
 				      int port);
+int mv88e6xxx_g2_eeprom_wait(struct mv88e6xxx_chip *chip);
 
 extern const struct mv88e6xxx_irq_ops mv88e6097_watchdog_ops;
 extern const struct mv88e6xxx_irq_ops mv88e6250_watchdog_ops;
 extern const struct mv88e6xxx_irq_ops mv88e6390_watchdog_ops;
+extern const struct mv88e6xxx_irq_ops mv88e6393x_watchdog_ops;
 
 extern const struct mv88e6xxx_avb_ops mv88e6165_avb_ops;
 extern const struct mv88e6xxx_avb_ops mv88e6352_avb_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/port.c
@@ -283,7 +283,7 @@
 	if (err)
 		return err;
 
-	if (speed)
+	if (speed != SPEED_UNFORCED)
 		dev_dbg(chip->dev, "p%d: Speed set to %d Mbps\n", port, speed);
 	else
 		dev_dbg(chip->dev, "p%d: Speed unforced\n", port);
@@ -516,7 +516,7 @@
 	if (err)
 		return err;
 
-	if (speed)
+	if (speed != SPEED_UNFORCED)
 		dev_dbg(chip->dev, "p%d: Speed set to %d Mbps\n", port, speed);
 	else
 		dev_dbg(chip->dev, "p%d: Speed unforced\n", port);
@@ -1699,6 +1699,7 @@
 	ptr = shift / 8;
 	shift %= 8;
 	mask >>= ptr * 8;
+	ptr <<= 8;
 
 	err = mv88e6393x_port_policy_read(chip, port, ptr, &reg);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/port.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/port.h
@@ -267,7 +267,7 @@
 /* Offset 0x10: Extended Port Control Command */
 #define MV88E6393X_PORT_EPC_CMD		0x10
 #define MV88E6393X_PORT_EPC_CMD_BUSY	0x8000
-#define MV88E6393X_PORT_EPC_CMD_WRITE	0x0300
+#define MV88E6393X_PORT_EPC_CMD_WRITE	0x3000
 #define MV88E6393X_PORT_EPC_INDEX_PORT_ETYPE	0x02
 
 /* Offset 0x11: Extended Port Control Data */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/port_hidden.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/port_hidden.c
@@ -40,8 +40,9 @@
 {
 	int bit = __bf_shf(MV88E6XXX_PORT_RESERVED_1A_BUSY);
 
-	return mv88e6xxx_wait_bit(chip, MV88E6XXX_PORT_RESERVED_1A_CTRL_PORT,
-				  MV88E6XXX_PORT_RESERVED_1A, bit, 0);
+	return mv88e6xxx_port_wait_bit(chip,
+				       MV88E6XXX_PORT_RESERVED_1A_CTRL_PORT,
+				       MV88E6XXX_PORT_RESERVED_1A, bit, 0);
 }
 
 int mv88e6xxx_port_hidden_read(struct mv88e6xxx_chip *chip, int block, int port,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/serdes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/serdes.c
@@ -50,11 +50,17 @@
 }
 
 static int mv88e6xxx_serdes_pcs_get_state(struct mv88e6xxx_chip *chip,
-					  u16 status, u16 lpa,
+					  u16 bmsr, u16 lpa, u16 status,
 					  struct phylink_link_state *state)
 {
+	state->link = !!(status & MV88E6390_SGMII_PHY_STATUS_LINK);
+	state->an_complete = !!(bmsr & BMSR_ANEGCOMPLETE);
+
 	if (status & MV88E6390_SGMII_PHY_STATUS_SPD_DPL_VALID) {
-		state->link = !!(status & MV88E6390_SGMII_PHY_STATUS_LINK);
+		/* The Spped and Duplex Resolved register is 1 if AN is enabled
+		 * and complete, or if AN is disabled. So with disabled AN we
+		 * still get here on link up.
+		 */
 		state->duplex = status &
 				MV88E6390_SGMII_PHY_STATUS_DUPLEX_FULL ?
 			                         DUPLEX_FULL : DUPLEX_HALF;
@@ -81,6 +87,18 @@
 			dev_err(chip->dev, "invalid PHY speed\n");
 			return -EINVAL;
 		}
+	} else if (state->link &&
+		   state->interface != PHY_INTERFACE_MODE_SGMII) {
+		/* If Speed and Duplex Resolved register is 0 and link is up, it
+		 * means that AN was enabled, but link partner had it disabled
+		 * and the PHY invoked the Auto-Negotiation Bypass feature and
+		 * linked anyway.
+		 */
+		state->duplex = DUPLEX_FULL;
+		if (state->interface == PHY_INTERFACE_MODE_2500BASEX)
+			state->speed = SPEED_2500;
+		else
+			state->speed = SPEED_1000;
 	} else {
 		state->link = false;
 	}
@@ -168,9 +186,15 @@
 int mv88e6352_serdes_pcs_get_state(struct mv88e6xxx_chip *chip, int port,
 				   int lane, struct phylink_link_state *state)
 {
-	u16 lpa, status;
+	u16 bmsr, lpa, status;
 	int err;
 
+	err = mv88e6352_serdes_read(chip, MII_BMSR, &bmsr);
+	if (err) {
+		dev_err(chip->dev, "can't read Serdes BMSR: %d\n", err);
+		return err;
+	}
+
 	err = mv88e6352_serdes_read(chip, 0x11, &status);
 	if (err) {
 		dev_err(chip->dev, "can't read Serdes PHY status: %d\n", err);
@@ -183,7 +207,7 @@
 		return err;
 	}
 
-	return mv88e6xxx_serdes_pcs_get_state(chip, status, lpa, state);
+	return mv88e6xxx_serdes_pcs_get_state(chip, bmsr, lpa, status, state);
 }
 
 int mv88e6352_serdes_pcs_an_restart(struct mv88e6xxx_chip *chip, int port,
@@ -314,8 +338,8 @@
 	return val;
 }
 
-int mv88e6352_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
-			       uint64_t *data)
+size_t mv88e6352_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
+				  uint64_t *data)
 {
 	struct mv88e6xxx_port *mv88e6xxx_port = &chip->ports[port];
 	struct mv88e6352_serdes_hw_stat *stat;
@@ -763,8 +787,8 @@
 	return reg[0] | ((u64)reg[1] << 16) | ((u64)reg[2] << 32);
 }
 
-int mv88e6390_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
-			       uint64_t *data)
+size_t mv88e6390_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
+				  uint64_t *data)
 {
 	struct mv88e6390_serdes_hw_stat *stat;
 	int lane;
@@ -801,7 +825,7 @@
 			   bool up)
 {
 	u8 cmode = chip->ports[port].cmode;
-	int err = 0;
+	int err;
 
 	switch (cmode) {
 	case MV88E6XXX_PORT_STS_CMODE_SGMII:
@@ -813,6 +837,9 @@
 	case MV88E6XXX_PORT_STS_CMODE_RXAUI:
 		err = mv88e6390_serdes_power_10g(chip, lane, up);
 		break;
+	default:
+		err = -EINVAL;
+		break;
 	}
 
 	if (!err && up)
@@ -883,10 +910,17 @@
 static int mv88e6390_serdes_pcs_get_state_sgmii(struct mv88e6xxx_chip *chip,
 	int port, int lane, struct phylink_link_state *state)
 {
-	u16 lpa, status;
+	u16 bmsr, lpa, status;
 	int err;
 
 	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_BMSR, &bmsr);
+	if (err) {
+		dev_err(chip->dev, "can't read Serdes PHY BMSR: %d\n", err);
+		return err;
+	}
+
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
 				    MV88E6390_SGMII_PHY_STATUS, &status);
 	if (err) {
 		dev_err(chip->dev, "can't read Serdes PHY status: %d\n", err);
@@ -900,7 +934,7 @@
 		return err;
 	}
 
-	return mv88e6xxx_serdes_pcs_get_state(chip, status, lpa, state);
+	return mv88e6xxx_serdes_pcs_get_state(chip, bmsr, lpa, status, state);
 }
 
 static int mv88e6390_serdes_pcs_get_state_10g(struct mv88e6xxx_chip *chip,
@@ -1271,9 +1305,31 @@
 	}
 }
 
-static int mv88e6393x_serdes_port_errata(struct mv88e6xxx_chip *chip, int lane)
+static int mv88e6393x_serdes_power_lane(struct mv88e6xxx_chip *chip, int lane,
+					bool on)
 {
-	u16 reg, pcs;
+	u16 reg;
+	int err;
+
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6393X_SERDES_CTRL1, &reg);
+	if (err)
+		return err;
+
+	if (on)
+		reg &= ~(MV88E6393X_SERDES_CTRL1_TX_PDOWN |
+			 MV88E6393X_SERDES_CTRL1_RX_PDOWN);
+	else
+		reg |= MV88E6393X_SERDES_CTRL1_TX_PDOWN |
+		       MV88E6393X_SERDES_CTRL1_RX_PDOWN;
+
+	return mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+				      MV88E6393X_SERDES_CTRL1, reg);
+}
+
+static int mv88e6393x_serdes_erratum_4_6(struct mv88e6xxx_chip *chip, int lane)
+{
+	u16 reg;
 	int err;
 
 	/* mv88e6393x family errata 4.6:
@@ -1284,26 +1340,45 @@
 	 * It seems that after this workaround the SERDES is automatically
 	 * powered up (the bit is cleared), so power it down.
 	 */
-	if (lane == MV88E6393X_PORT0_LANE || lane == MV88E6393X_PORT9_LANE ||
-	    lane == MV88E6393X_PORT10_LANE) {
-		err = mv88e6390_serdes_read(chip, lane,
-					    MDIO_MMD_PHYXS,
-					    MV88E6393X_SERDES_POC, &reg);
-		if (err)
-			return err;
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6393X_SERDES_POC, &reg);
+	if (err)
+		return err;
 
-		reg &= ~MV88E6393X_SERDES_POC_PDOWN;
-		reg |= MV88E6393X_SERDES_POC_RESET;
+	reg &= ~MV88E6393X_SERDES_POC_PDOWN;
+	reg |= MV88E6393X_SERDES_POC_RESET;
 
-		err = mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
-					     MV88E6393X_SERDES_POC, reg);
-		if (err)
-			return err;
+	err = mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+				     MV88E6393X_SERDES_POC, reg);
+	if (err)
+		return err;
 
-		err = mv88e6390_serdes_power_sgmii(chip, lane, false);
-		if (err)
-			return err;
-	}
+	err = mv88e6390_serdes_power_sgmii(chip, lane, false);
+	if (err)
+		return err;
+
+	return mv88e6393x_serdes_power_lane(chip, lane, false);
+}
+
+int mv88e6393x_serdes_setup_errata(struct mv88e6xxx_chip *chip)
+{
+	int err;
+
+	err = mv88e6393x_serdes_erratum_4_6(chip, MV88E6393X_PORT0_LANE);
+	if (err)
+		return err;
+
+	err = mv88e6393x_serdes_erratum_4_6(chip, MV88E6393X_PORT9_LANE);
+	if (err)
+		return err;
+
+	return mv88e6393x_serdes_erratum_4_6(chip, MV88E6393X_PORT10_LANE);
+}
+
+static int mv88e6393x_serdes_erratum_4_8(struct mv88e6xxx_chip *chip, int lane)
+{
+	u16 reg, pcs;
+	int err;
 
 	/* mv88e6393x family errata 4.8:
 	 * When a SERDES port is operating in 1000BASE-X or SGMII mode link may
@@ -1334,38 +1409,152 @@
 				      MV88E6393X_ERRATA_4_8_REG, reg);
 }
 
-int mv88e6393x_serdes_setup_errata(struct mv88e6xxx_chip *chip)
+static int mv88e6393x_serdes_erratum_5_2(struct mv88e6xxx_chip *chip, int lane,
+					 u8 cmode)
 {
+	static const struct {
+		u16 dev, reg, val, mask;
+	} fixes[] = {
+		{ MDIO_MMD_VEND1, 0x8093, 0xcb5a, 0xffff },
+		{ MDIO_MMD_VEND1, 0x8171, 0x7088, 0xffff },
+		{ MDIO_MMD_VEND1, 0x80c9, 0x311a, 0xffff },
+		{ MDIO_MMD_VEND1, 0x80a2, 0x8000, 0xff7f },
+		{ MDIO_MMD_VEND1, 0x80a9, 0x0000, 0xfff0 },
+		{ MDIO_MMD_VEND1, 0x80a3, 0x0000, 0xf8ff },
+		{ MDIO_MMD_PHYXS, MV88E6393X_SERDES_POC,
+		  MV88E6393X_SERDES_POC_RESET, MV88E6393X_SERDES_POC_RESET },
+	};
+	int err, i;
+	u16 reg;
+
+	/* mv88e6393x family errata 5.2:
+	 * For optimal signal integrity the following sequence should be applied
+	 * to SERDES operating in 10G mode. These registers only apply to 10G
+	 * operation and have no effect on other speeds.
+	 */
+	if (cmode != MV88E6393X_PORT_STS_CMODE_10GBASER)
+		return 0;
+
+	for (i = 0; i < ARRAY_SIZE(fixes); ++i) {
+		err = mv88e6390_serdes_read(chip, lane, fixes[i].dev,
+					    fixes[i].reg, &reg);
+		if (err)
+			return err;
+
+		reg &= ~fixes[i].mask;
+		reg |= fixes[i].val;
+
+		err = mv88e6390_serdes_write(chip, lane, fixes[i].dev,
+					     fixes[i].reg, reg);
+		if (err)
+			return err;
+	}
+
+	return 0;
+}
+
+static int mv88e6393x_serdes_fix_2500basex_an(struct mv88e6xxx_chip *chip,
+					      int lane, u8 cmode, bool on)
+{
+	u16 reg;
 	int err;
 
-	err = mv88e6393x_serdes_port_errata(chip, MV88E6393X_PORT0_LANE);
+	if (cmode != MV88E6XXX_PORT_STS_CMODE_2500BASEX)
+		return 0;
+
+	/* Inband AN is broken on Amethyst in 2500base-x mode when set by
+	 * standard mechanism (via cmode).
+	 * We can get around this by configuring the PCS mode to 1000base-x
+	 * and then writing value 0x58 to register 1e.8000. (This must be done
+	 * while SerDes receiver and transmitter are disabled, which is, when
+	 * this function is called.)
+	 * It seem that when we do this configuration to 2500base-x mode (by
+	 * changing PCS mode to 1000base-x and frequency to 3.125 GHz from
+	 * 1.25 GHz) and then configure to sgmii or 1000base-x, the device
+	 * thinks that it already has SerDes at 1.25 GHz and does not change
+	 * the 1e.8000 register, leaving SerDes at 3.125 GHz.
+	 * To avoid this, change PCS mode back to 2500base-x when disabling
+	 * SerDes from 2500base-x mode.
+	 */
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6393X_SERDES_POC, &reg);
+	if (err)
+		return err;
+
+	reg &= ~(MV88E6393X_SERDES_POC_PCS_MASK | MV88E6393X_SERDES_POC_AN);
+	if (on)
+		reg |= MV88E6393X_SERDES_POC_PCS_1000BASEX |
+		       MV88E6393X_SERDES_POC_AN;
+	else
+		reg |= MV88E6393X_SERDES_POC_PCS_2500BASEX;
+	reg |= MV88E6393X_SERDES_POC_RESET;
+
+	err = mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+				     MV88E6393X_SERDES_POC, reg);
 	if (err)
 		return err;
 
-	err = mv88e6393x_serdes_port_errata(chip, MV88E6393X_PORT9_LANE);
+	err = mv88e6390_serdes_write(chip, lane, MDIO_MMD_VEND1, 0x8000, 0x58);
 	if (err)
 		return err;
 
-	return mv88e6393x_serdes_port_errata(chip, MV88E6393X_PORT10_LANE);
+	return 0;
 }
 
 int mv88e6393x_serdes_power(struct mv88e6xxx_chip *chip, int port, int lane,
 			    bool on)
 {
 	u8 cmode = chip->ports[port].cmode;
+	int err;
 
 	if (port != 0 && port != 9 && port != 10)
 		return -EOPNOTSUPP;
 
+	if (on) {
+		err = mv88e6393x_serdes_erratum_4_8(chip, lane);
+		if (err)
+			return err;
+
+		err = mv88e6393x_serdes_erratum_5_2(chip, lane, cmode);
+		if (err)
+			return err;
+
+		err = mv88e6393x_serdes_fix_2500basex_an(chip, lane, cmode,
+							 true);
+		if (err)
+			return err;
+
+		err = mv88e6393x_serdes_power_lane(chip, lane, true);
+		if (err)
+			return err;
+	}
+
 	switch (cmode) {
 	case MV88E6XXX_PORT_STS_CMODE_SGMII:
 	case MV88E6XXX_PORT_STS_CMODE_1000BASEX:
 	case MV88E6XXX_PORT_STS_CMODE_2500BASEX:
-		return mv88e6390_serdes_power_sgmii(chip, lane, on);
+		err = mv88e6390_serdes_power_sgmii(chip, lane, on);
+		break;
 	case MV88E6393X_PORT_STS_CMODE_5GBASER:
 	case MV88E6393X_PORT_STS_CMODE_10GBASER:
-		return mv88e6390_serdes_power_10g(chip, lane, on);
+		err = mv88e6390_serdes_power_10g(chip, lane, on);
+		break;
+	default:
+		err = -EINVAL;
+		break;
 	}
 
-	return 0;
+	if (err)
+		return err;
+
+	if (!on) {
+		err = mv88e6393x_serdes_power_lane(chip, lane, false);
+		if (err)
+			return err;
+
+		err = mv88e6393x_serdes_fix_2500basex_an(chip, lane, cmode,
+							 false);
+	}
+
+	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/serdes.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/serdes.h
@@ -93,6 +93,10 @@
 #define MV88E6393X_SERDES_POC_PCS_MASK		0x0007
 #define MV88E6393X_SERDES_POC_RESET		BIT(15)
 #define MV88E6393X_SERDES_POC_PDOWN		BIT(5)
+#define MV88E6393X_SERDES_POC_AN		BIT(3)
+#define MV88E6393X_SERDES_CTRL1			0xf003
+#define MV88E6393X_SERDES_CTRL1_TX_PDOWN	BIT(9)
+#define MV88E6393X_SERDES_CTRL1_RX_PDOWN	BIT(8)
 
 #define MV88E6393X_ERRATA_4_8_REG		0xF074
 #define MV88E6393X_ERRATA_4_8_BIT		BIT(14)
@@ -159,13 +163,13 @@
 int mv88e6352_serdes_get_sset_count(struct mv88e6xxx_chip *chip, int port);
 int mv88e6352_serdes_get_strings(struct mv88e6xxx_chip *chip,
 				 int port, uint8_t *data);
-int mv88e6352_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
-			       uint64_t *data);
+size_t mv88e6352_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
+				  uint64_t *data);
 int mv88e6390_serdes_get_sset_count(struct mv88e6xxx_chip *chip, int port);
 int mv88e6390_serdes_get_strings(struct mv88e6xxx_chip *chip,
 				 int port, uint8_t *data);
-int mv88e6390_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
-			       uint64_t *data);
+size_t mv88e6390_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
+				  uint64_t *data);
 
 int mv88e6352_serdes_get_regs_len(struct mv88e6xxx_chip *chip, int port);
 void mv88e6352_serdes_get_regs(struct mv88e6xxx_chip *chip, int port, void *_p);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/trace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/trace.c
@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* Copyright 2022 NXP
+ */
+
+#define CREATE_TRACE_POINTS
+#include "trace.h"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/mv88e6xxx/trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/mv88e6xxx/trace.h
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright 2022 NXP
+ */
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM	mv88e6xxx
+
+#if !defined(_MV88E6XXX_TRACE_H) || defined(TRACE_HEADER_MULTI_READ)
+#define _MV88E6XXX_TRACE_H
+
+#include <linux/device.h>
+#include <linux/if_ether.h>
+#include <linux/tracepoint.h>
+
+DECLARE_EVENT_CLASS(mv88e6xxx_atu_violation,
+
+	TP_PROTO(const struct device *dev, int spid, u16 portvec,
+		 const unsigned char *addr, u16 fid),
+
+	TP_ARGS(dev, spid, portvec, addr, fid),
+
+	TP_STRUCT__entry(
+		__string(name, dev_name(dev))
+		__field(int, spid)
+		__field(u16, portvec)
+		__array(unsigned char, addr, ETH_ALEN)
+		__field(u16, fid)
+	),
+
+	TP_fast_assign(
+		__assign_str(name, dev_name(dev));
+		__entry->spid = spid;
+		__entry->portvec = portvec;
+		memcpy(__entry->addr, addr, ETH_ALEN);
+		__entry->fid = fid;
+	),
+
+	TP_printk("dev %s spid %d portvec 0x%x addr %pM fid %u",
+		  __get_str(name), __entry->spid, __entry->portvec,
+		  __entry->addr, __entry->fid)
+);
+
+DEFINE_EVENT(mv88e6xxx_atu_violation, mv88e6xxx_atu_member_violation,
+	     TP_PROTO(const struct device *dev, int spid, u16 portvec,
+		      const unsigned char *addr, u16 fid),
+	     TP_ARGS(dev, spid, portvec, addr, fid));
+
+DEFINE_EVENT(mv88e6xxx_atu_violation, mv88e6xxx_atu_miss_violation,
+	     TP_PROTO(const struct device *dev, int spid, u16 portvec,
+		      const unsigned char *addr, u16 fid),
+	     TP_ARGS(dev, spid, portvec, addr, fid));
+
+DEFINE_EVENT(mv88e6xxx_atu_violation, mv88e6xxx_atu_full_violation,
+	     TP_PROTO(const struct device *dev, int spid, u16 portvec,
+		      const unsigned char *addr, u16 fid),
+	     TP_ARGS(dev, spid, portvec, addr, fid));
+
+#endif /* _MV88E6XXX_TRACE_H */
+
+/* We don't want to use include/trace/events */
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH .
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_FILE	trace
+/* This part must be outside protection */
+#include <trace/define_trace.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/ocelot/felix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/ocelot/felix.c
@@ -290,8 +290,11 @@
 		}
 	}
 
-	if (cpu < 0)
+	if (cpu < 0) {
+		kfree(tagging_rule);
+		kfree(redirect_rule);
 		return -EINVAL;
+	}
 
 	tagging_rule->key_type = OCELOT_VCAP_KEY_ETYPE;
 	*(__be16 *)tagging_rule->key.etype.etype.value = htons(ETH_P_1588);
@@ -1368,12 +1371,12 @@
 static bool felix_rxtstamp(struct dsa_switch *ds, int port,
 			   struct sk_buff *skb, unsigned int type)
 {
-	u8 *extraction = skb->data - ETH_HLEN - OCELOT_TAG_LEN;
+	u32 tstamp_lo = OCELOT_SKB_CB(skb)->tstamp_lo;
 	struct skb_shared_hwtstamps *shhwtstamps;
 	struct ocelot *ocelot = ds->priv;
-	u32 tstamp_lo, tstamp_hi;
 	struct timespec64 ts;
-	u64 tstamp, val;
+	u32 tstamp_hi;
+	u64 tstamp;
 
 	/* If the "no XTR IRQ" workaround is in use, tell DSA to defer this skb
 	 * for RX timestamping. Then free it, and poll for its copy through
@@ -1388,9 +1391,6 @@
 	ocelot_ptp_gettime64(&ocelot->ptp_info, &ts);
 	tstamp = ktime_set(ts.tv_sec, ts.tv_nsec);
 
-	ocelot_xfh_get_rew_val(extraction, &val);
-	tstamp_lo = (u32)val;
-
 	tstamp_hi = tstamp >> 32;
 	if ((tstamp & 0xffffffff) < tstamp_lo)
 		tstamp_hi--;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -578,7 +578,8 @@
 	{ .offset = 0x87,	.name = "tx_frames_below_65_octets", },
 	{ .offset = 0x88,	.name = "tx_frames_65_to_127_octets", },
 	{ .offset = 0x89,	.name = "tx_frames_128_255_octets", },
-	{ .offset = 0x8B,	.name = "tx_frames_256_511_octets", },
+	{ .offset = 0x8A,	.name = "tx_frames_256_511_octets", },
+	{ .offset = 0x8B,	.name = "tx_frames_512_1023_octets", },
 	{ .offset = 0x8C,	.name = "tx_frames_1024_1526_octets", },
 	{ .offset = 0x8D,	.name = "tx_frames_over_1526_octets", },
 	{ .offset = 0x8E,	.name = "tx_yellow_prio_0", },
@@ -1066,7 +1067,7 @@
 		return PTR_ERR(hw);
 	}
 
-	bus = devm_mdiobus_alloc_size(dev, sizeof(*mdio_priv));
+	bus = mdiobus_alloc_size(sizeof(*mdio_priv));
 	if (!bus)
 		return -ENOMEM;
 
@@ -1086,6 +1087,7 @@
 	rc = mdiobus_register(bus);
 	if (rc < 0) {
 		dev_err(dev, "failed to register MDIO bus\n");
+		mdiobus_free(bus);
 		return rc;
 	}
 
@@ -1135,6 +1137,7 @@
 		lynx_pcs_destroy(pcs);
 	}
 	mdiobus_unregister(felix->imdio);
+	mdiobus_free(felix->imdio);
 }
 
 static void vsc9959_sched_speed_set(struct ocelot *ocelot, int port,
@@ -1453,7 +1456,7 @@
 
 	err = dsa_register_switch(ds);
 	if (err) {
-		dev_err(&pdev->dev, "Failed to register DSA switch: %d\n", err);
+		dev_err_probe(&pdev->dev, err, "Failed to register DSA switch\n");
 		goto err_register_ds;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/ocelot/seville_vsc9953.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/ocelot/seville_vsc9953.c
@@ -10,6 +10,7 @@
 #include <linux/pcs-lynx.h>
 #include <linux/dsa/ocelot.h>
 #include <linux/iopoll.h>
+#include <linux/of_mdio.h>
 #include "felix.h"
 
 #define MSCC_MIIM_CMD_OPR_WRITE			BIT(1)
@@ -1110,7 +1111,7 @@
 	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-imdio", dev_name(dev));
 
 	/* Needed in order to initialize the bus mutex lock */
-	rc = mdiobus_register(bus);
+	rc = devm_of_mdiobus_register(dev, bus, NULL);
 	if (rc < 0) {
 		dev_err(dev, "failed to register MDIO bus\n");
 		return rc;
@@ -1162,7 +1163,8 @@
 		mdio_device_free(pcs->mdio);
 		lynx_pcs_destroy(pcs);
 	}
-	mdiobus_unregister(felix->imdio);
+
+	/* mdiobus_unregister and mdiobus_free handled by devres */
 }
 
 static const struct felix_info seville_info_vsc9953 = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/qca/ar9331.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/qca/ar9331.c
@@ -378,7 +378,7 @@
 	if (!mnp)
 		return -ENODEV;
 
-	ret = of_mdiobus_register(mbus, mnp);
+	ret = devm_of_mdiobus_register(dev, mbus, mnp);
 	of_node_put(mnp);
 	if (ret)
 		return ret;
@@ -1093,7 +1093,6 @@
 	}
 
 	irq_domain_remove(priv->irqdomain);
-	mdiobus_unregister(priv->mbus);
 	dsa_unregister_switch(&priv->ds);
 
 	reset_control_assert(priv->sw_reset);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/qca8k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/qca8k.c
@@ -1599,7 +1599,7 @@
 qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 {
 	struct qca8k_priv *priv = ds->priv;
-	int i, mtu = 0;
+	int ret, i, mtu = 0;
 
 	priv->port_mtu[port] = new_mtu;
 
@@ -1607,8 +1607,27 @@
 		if (priv->port_mtu[i] > mtu)
 			mtu = priv->port_mtu[i];
 
+	/* To change the MAX_FRAME_SIZE the cpu ports must be off or
+	 * the switch panics.
+	 * Turn off both cpu ports before applying the new value to prevent
+	 * this.
+	 */
+	if (priv->port_sts[0].enabled)
+		qca8k_port_set_status(priv, 0, 0);
+
+	if (priv->port_sts[6].enabled)
+		qca8k_port_set_status(priv, 6, 0);
+
 	/* Include L2 header / FCS length */
-	return qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN);
+	ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN);
+
+	if (priv->port_sts[0].enabled)
+		qca8k_port_set_status(priv, 0, 1);
+
+	if (priv->port_sts[6].enabled)
+		qca8k_port_set_status(priv, 6, 1);
+
+	return ret;
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/rtl8366.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/rtl8366.c
@@ -457,7 +457,7 @@
 			 * anymore then clear the whole member
 			 * config so it can be reused.
 			 */
-			if (!vlanmc.member && vlanmc.untag) {
+			if (!vlanmc.member) {
 				vlanmc.vid = 0;
 				vlanmc.priority = 0;
 				vlanmc.fid = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/rtl8366rb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/rtl8366rb.c
@@ -1350,7 +1350,7 @@
 
 static bool rtl8366rb_is_vlan_valid(struct realtek_smi *smi, unsigned int vlan)
 {
-	unsigned int max = RTL8366RB_NUM_VLANS;
+	unsigned int max = RTL8366RB_NUM_VLANS - 1;
 
 	if (smi->vlan4k_enabled)
 		max = RTL8366RB_NUM_VIDS - 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/sja1105/sja1105.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/sja1105/sja1105.h
@@ -111,6 +111,8 @@
 	int max_frame_mem;
 	int num_ports;
 	bool multiple_cascade_ports;
+	/* Every {port, TXQ} has its own CBS shaper */
+	bool fixed_cbs_mapping;
 	enum dsa_tag_protocol tag_proto;
 	const struct sja1105_dynamic_table_ops *dyn_ops;
 	const struct sja1105_table_ops *static_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/sja1105/sja1105_devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/sja1105/sja1105_devlink.c
@@ -93,8 +93,10 @@
 
 		region = dsa_devlink_region_create(ds, ops, 1, size);
 		if (IS_ERR(region)) {
-			while (i-- >= 0)
+			while (--i >= 0)
 				dsa_devlink_region_destroy(priv->regions[i]);
+
+			kfree(priv->regions);
 			return PTR_ERR(region);
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/sja1105/sja1105_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/sja1105/sja1105_main.c
@@ -853,11 +853,11 @@
 		.hostprio = 7,
 		.mac_fltres1 = SJA1105_LINKLOCAL_FILTER_A,
 		.mac_flt1    = SJA1105_LINKLOCAL_FILTER_A_MASK,
-		.incl_srcpt1 = false,
+		.incl_srcpt1 = true,
 		.send_meta1  = false,
 		.mac_fltres0 = SJA1105_LINKLOCAL_FILTER_B,
 		.mac_flt0    = SJA1105_LINKLOCAL_FILTER_B_MASK,
-		.incl_srcpt0 = false,
+		.incl_srcpt0 = true,
 		.send_meta0  = false,
 		/* Default to an invalid value */
 		.mirr_port = priv->ds->num_ports,
@@ -1025,7 +1025,7 @@
 
 		policing[bcast].sharindx = port;
 		/* Only SJA1110 has multicast policers */
-		if (mcast <= table->ops->max_entry_count)
+		if (mcast < table->ops->max_entry_count)
 			policing[mcast].sharindx = port;
 	}
 
@@ -1794,13 +1794,14 @@
 		if (!(l2_lookup.destports & BIT(port)))
 			continue;
 
-		/* We need to hide the FDB entry for unknown multicast */
-		if (l2_lookup.macaddr == SJA1105_UNKNOWN_MULTICAST &&
-		    l2_lookup.mask_macaddr == SJA1105_UNKNOWN_MULTICAST)
-			continue;
-
 		u64_to_ether_addr(l2_lookup.macaddr, macaddr);
 
+		/* Hardware FDB is shared for fdb and mdb, "bridge fdb show"
+		 * only wants to see unicast
+		 */
+		if (is_multicast_ether_addr(macaddr))
+			continue;
+
 		/* We need to hide the dsa_8021q VLANs from the user. */
 		if (!priv->vlan_aware)
 			l2_lookup.vlanid = 0;
@@ -2014,11 +2015,36 @@
 }
 
 #define BYTES_PER_KBIT (1000LL / 8)
+/* Port 0 (the uC port) does not have CBS shapers */
+#define SJA1110_FIXED_CBS(port, prio) ((((port) - 1) * SJA1105_NUM_TC) + (prio))
+
+static int sja1105_find_cbs_shaper(struct sja1105_private *priv,
+				   int port, int prio)
+{
+	int i;
+
+	if (priv->info->fixed_cbs_mapping) {
+		i = SJA1110_FIXED_CBS(port, prio);
+		if (i >= 0 && i < priv->info->num_cbs_shapers)
+			return i;
+
+		return -1;
+	}
+
+	for (i = 0; i < priv->info->num_cbs_shapers; i++)
+		if (priv->cbs[i].port == port && priv->cbs[i].prio == prio)
+			return i;
+
+	return -1;
+}
 
 static int sja1105_find_unused_cbs_shaper(struct sja1105_private *priv)
 {
 	int i;
 
+	if (priv->info->fixed_cbs_mapping)
+		return -1;
+
 	for (i = 0; i < priv->info->num_cbs_shapers; i++)
 		if (!priv->cbs[i].idle_slope && !priv->cbs[i].send_slope)
 			return i;
@@ -2049,14 +2075,20 @@
 {
 	struct sja1105_private *priv = ds->priv;
 	struct sja1105_cbs_entry *cbs;
+	s64 port_transmit_rate_kbps;
 	int index;
 
 	if (!offload->enable)
 		return sja1105_delete_cbs_shaper(priv, port, offload->queue);
 
-	index = sja1105_find_unused_cbs_shaper(priv);
-	if (index < 0)
-		return -ENOSPC;
+	/* The user may be replacing an existing shaper */
+	index = sja1105_find_cbs_shaper(priv, port, offload->queue);
+	if (index < 0) {
+		/* That isn't the case - see if we can allocate a new one */
+		index = sja1105_find_unused_cbs_shaper(priv);
+		if (index < 0)
+			return -ENOSPC;
+	}
 
 	cbs = &priv->cbs[index];
 	cbs->port = port;
@@ -2066,9 +2098,17 @@
 	 */
 	cbs->credit_hi = offload->hicredit;
 	cbs->credit_lo = abs(offload->locredit);
-	/* User space is in kbits/sec, hardware in bytes/sec */
-	cbs->idle_slope = offload->idleslope * BYTES_PER_KBIT;
-	cbs->send_slope = abs(offload->sendslope * BYTES_PER_KBIT);
+	/* User space is in kbits/sec, while the hardware in bytes/sec times
+	 * link speed. Since the given offload->sendslope is good only for the
+	 * current link speed anyway, and user space is likely to reprogram it
+	 * when that changes, don't even bother to track the port's link speed,
+	 * but deduce the port transmit rate from idleslope - sendslope.
+	 */
+	port_transmit_rate_kbps = offload->idleslope - offload->sendslope;
+	cbs->idle_slope = div_s64(offload->idleslope * BYTES_PER_KBIT,
+				  port_transmit_rate_kbps);
+	cbs->send_slope = div_s64(abs(offload->sendslope * BYTES_PER_KBIT),
+				  port_transmit_rate_kbps);
 	/* Convert the negative values from 64-bit 2's complement
 	 * to 32-bit 2's complement (for the case of 0x80000000 whose
 	 * negative is still negative).
@@ -2306,11 +2346,6 @@
 	general_params->tpid = tpid;
 	/* EtherType used to identify outer tagged (S-tag) VLAN traffic */
 	general_params->tpid2 = tpid2;
-	/* When VLAN filtering is on, we need to at least be able to
-	 * decode management traffic through the "backup plan".
-	 */
-	general_params->incl_srcpt1 = enabled;
-	general_params->incl_srcpt0 = enabled;
 
 	/* VLAN filtering => independent VLAN learning.
 	 * No VLAN filtering (or best effort) => shared VLAN learning.
@@ -3372,12 +3407,28 @@
 };
 MODULE_DEVICE_TABLE(of, sja1105_dt_ids);
 
+static const struct spi_device_id sja1105_spi_ids[] = {
+	{ "sja1105e" },
+	{ "sja1105t" },
+	{ "sja1105p" },
+	{ "sja1105q" },
+	{ "sja1105r" },
+	{ "sja1105s" },
+	{ "sja1110a" },
+	{ "sja1110b" },
+	{ "sja1110c" },
+	{ "sja1110d" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, sja1105_spi_ids);
+
 static struct spi_driver sja1105_driver = {
 	.driver = {
 		.name  = "sja1105",
 		.owner = THIS_MODULE,
 		.of_match_table = of_match_ptr(sja1105_dt_ids),
 	},
+	.id_table = sja1105_spi_ids,
 	.probe  = sja1105_probe,
 	.remove = sja1105_remove,
 	.shutdown = sja1105_shutdown,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/sja1105/sja1105_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/sja1105/sja1105_mdio.c
@@ -256,6 +256,9 @@
 	u32 tmp;
 	int rc;
 
+	if (reg & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
 	rc = sja1105_xfer_u32(priv, SPI_READ, regs->mdio_100base_tx + reg,
 			      &tmp, NULL);
 	if (rc < 0)
@@ -272,6 +275,9 @@
 	const struct sja1105_regs *regs = priv->info->regs;
 	u32 tmp = val;
 
+	if (reg & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
 	return sja1105_xfer_u32(priv, SPI_WRITE, regs->mdio_100base_tx + reg,
 				&tmp, NULL);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/sja1105/sja1105_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/sja1105/sja1105_spi.c
@@ -781,6 +781,7 @@
 	.tag_proto		= DSA_TAG_PROTO_SJA1110,
 	.can_limit_mcast_flood	= true,
 	.multiple_cascade_ports	= true,
+	.fixed_cbs_mapping	= true,
 	.ptp_ts_bits		= 32,
 	.ptpegr_ts_bytes	= 8,
 	.max_frame_mem		= SJA1110_MAX_FRAME_MEMORY,
@@ -831,6 +832,7 @@
 	.tag_proto		= DSA_TAG_PROTO_SJA1110,
 	.can_limit_mcast_flood	= true,
 	.multiple_cascade_ports	= true,
+	.fixed_cbs_mapping	= true,
 	.ptp_ts_bits		= 32,
 	.ptpegr_ts_bytes	= 8,
 	.max_frame_mem		= SJA1110_MAX_FRAME_MEMORY,
@@ -881,6 +883,7 @@
 	.tag_proto		= DSA_TAG_PROTO_SJA1110,
 	.can_limit_mcast_flood	= true,
 	.multiple_cascade_ports	= true,
+	.fixed_cbs_mapping	= true,
 	.ptp_ts_bits		= 32,
 	.ptpegr_ts_bytes	= 8,
 	.max_frame_mem		= SJA1110_MAX_FRAME_MEMORY,
@@ -931,6 +934,7 @@
 	.tag_proto		= DSA_TAG_PROTO_SJA1110,
 	.can_limit_mcast_flood	= true,
 	.multiple_cascade_ports	= true,
+	.fixed_cbs_mapping	= true,
 	.ptp_ts_bits		= 32,
 	.ptpegr_ts_bytes	= 8,
 	.max_frame_mem		= SJA1110_MAX_FRAME_MEMORY,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/vitesse-vsc73xx-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/vitesse-vsc73xx-core.c
@@ -17,6 +17,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/device.h>
+#include <linux/iopoll.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_mdio.h>
@@ -34,10 +35,14 @@
 #define VSC73XX_BLOCK_ANALYZER	0x2 /* Only subblock 0 */
 #define VSC73XX_BLOCK_MII	0x3 /* Subblocks 0 and 1 */
 #define VSC73XX_BLOCK_MEMINIT	0x3 /* Only subblock 2 */
-#define VSC73XX_BLOCK_CAPTURE	0x4 /* Only subblock 2 */
+#define VSC73XX_BLOCK_CAPTURE	0x4 /* Subblocks 0-4, 6, 7 */
 #define VSC73XX_BLOCK_ARBITER	0x5 /* Only subblock 0 */
 #define VSC73XX_BLOCK_SYSTEM	0x7 /* Only subblock 0 */
 
+/* MII Block subblock */
+#define VSC73XX_BLOCK_MII_INTERNAL	0x0 /* Internal MDIO subblock */
+#define VSC73XX_BLOCK_MII_EXTERNAL	0x1 /* External MDIO subblock */
+
 #define CPU_PORT	6 /* CPU port */
 
 /* MAC Block registers */
@@ -196,6 +201,8 @@
 #define VSC73XX_MII_CMD		0x1
 #define VSC73XX_MII_DATA	0x2
 
+#define VSC73XX_MII_STAT_BUSY	BIT(3)
+
 /* Arbiter block 5 registers */
 #define VSC73XX_ARBEMPTY		0x0c
 #define VSC73XX_ARBDISC			0x0e
@@ -269,6 +276,10 @@
 #define IS_7398(a) ((a)->chipid == VSC73XX_CHIPID_ID_7398)
 #define IS_739X(a) (IS_7395(a) || IS_7398(a))
 
+#define VSC73XX_POLL_SLEEP_US		1000
+#define VSC73XX_MDIO_POLL_SLEEP_US	5
+#define VSC73XX_POLL_TIMEOUT_US		10000
+
 struct vsc73xx_counter {
 	u8 counter;
 	const char *name;
@@ -360,13 +371,19 @@
 		break;
 
 	case VSC73XX_BLOCK_MII:
-	case VSC73XX_BLOCK_CAPTURE:
 	case VSC73XX_BLOCK_ARBITER:
 		switch (subblock) {
 		case 0 ... 1:
 			return 1;
 		}
 		break;
+	case VSC73XX_BLOCK_CAPTURE:
+		switch (subblock) {
+		case 0 ... 4:
+		case 6 ... 7:
+			return 1;
+		}
+		break;
 	}
 
 	return 0;
@@ -484,6 +501,22 @@
 	return 0;
 }
 
+static int vsc73xx_mdio_busy_check(struct vsc73xx *vsc)
+{
+	int ret, err;
+	u32 val;
+
+	ret = read_poll_timeout(vsc73xx_read, err,
+				err < 0 || !(val & VSC73XX_MII_STAT_BUSY),
+				VSC73XX_MDIO_POLL_SLEEP_US,
+				VSC73XX_POLL_TIMEOUT_US, false, vsc,
+				VSC73XX_BLOCK_MII, VSC73XX_BLOCK_MII_INTERNAL,
+				VSC73XX_MII_STAT, &val);
+	if (ret)
+		return ret;
+	return err;
+}
+
 static int vsc73xx_phy_read(struct dsa_switch *ds, int phy, int regnum)
 {
 	struct vsc73xx *vsc = ds->priv;
@@ -491,12 +524,20 @@
 	u32 val;
 	int ret;
 
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
+
 	/* Setting bit 26 means "read" */
 	cmd = BIT(26) | (phy << 21) | (regnum << 16);
 	ret = vsc73xx_write(vsc, VSC73XX_BLOCK_MII, 0, 1, cmd);
 	if (ret)
 		return ret;
-	msleep(2);
+
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
+
 	ret = vsc73xx_read(vsc, VSC73XX_BLOCK_MII, 0, 2, &val);
 	if (ret)
 		return ret;
@@ -520,6 +561,10 @@
 	u32 cmd;
 	int ret;
 
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
+
 	/* It was found through tedious experiments that this router
 	 * chip really hates to have it's PHYs reset. They
 	 * never recover if that happens: autonegotiation stops
@@ -531,7 +576,7 @@
 		return 0;
 	}
 
-	cmd = (phy << 21) | (regnum << 16);
+	cmd = (phy << 21) | (regnum << 16) | val;
 	ret = vsc73xx_write(vsc, VSC73XX_BLOCK_MII, 0, 1, cmd);
 	if (ret)
 		return ret;
@@ -780,7 +825,7 @@
 	 * after a PHY or the CPU port comes up or down.
 	 */
 	if (!phydev->link) {
-		int maxloop = 10;
+		int ret, err;
 
 		dev_dbg(vsc->dev, "port %d: went down\n",
 			port);
@@ -795,19 +840,17 @@
 				    VSC73XX_ARBDISC, BIT(port), BIT(port));
 
 		/* Wait until queue is empty */
-		vsc73xx_read(vsc, VSC73XX_BLOCK_ARBITER, 0,
-			     VSC73XX_ARBEMPTY, &val);
-		while (!(val & BIT(port))) {
-			msleep(1);
-			vsc73xx_read(vsc, VSC73XX_BLOCK_ARBITER, 0,
-				     VSC73XX_ARBEMPTY, &val);
-			if (--maxloop == 0) {
-				dev_err(vsc->dev,
-					"timeout waiting for block arbiter\n");
-				/* Continue anyway */
-				break;
-			}
-		}
+		ret = read_poll_timeout(vsc73xx_read, err,
+					err < 0 || (val & BIT(port)),
+					VSC73XX_POLL_SLEEP_US,
+					VSC73XX_POLL_TIMEOUT_US, false,
+					vsc, VSC73XX_BLOCK_ARBITER, 0,
+					VSC73XX_ARBEMPTY, &val);
+		if (ret)
+			dev_err(vsc->dev,
+				"timeout waiting for block arbiter\n");
+		else if (err < 0)
+			dev_err(vsc->dev, "error reading arbiter\n");
 
 		/* Put this port into reset */
 		vsc73xx_write(vsc, VSC73XX_BLOCK_MAC, port, VSC73XX_MAC_CFG,
@@ -1025,17 +1068,17 @@
 	struct vsc73xx *vsc = ds->priv;
 
 	return vsc73xx_write(vsc, VSC73XX_BLOCK_MAC, port,
-			     VSC73XX_MAXLEN, new_mtu);
+			     VSC73XX_MAXLEN, new_mtu + ETH_HLEN + ETH_FCS_LEN);
 }
 
 /* According to application not "VSC7398 Jumbo Frames" setting
- * up the MTU to 9.6 KB does not affect the performance on standard
+ * up the frame size to 9.6 KB does not affect the performance on standard
  * frames. It is clear from the application note that
  * "9.6 kilobytes" == 9600 bytes.
  */
 static int vsc73xx_get_max_mtu(struct dsa_switch *ds, int port)
 {
-	return 9600;
+	return 9600 - ETH_HLEN - ETH_FCS_LEN;
 }
 
 static const struct dsa_switch_ops vsc73xx_ds_ops = {
@@ -1119,6 +1162,8 @@
 
 	vsc->gc.label = devm_kasprintf(vsc->dev, GFP_KERNEL, "VSC%04x",
 				       vsc->chipid);
+	if (!vsc->gc.label)
+		return -ENOMEM;
 	vsc->gc.ngpio = 4;
 	vsc->gc.owner = THIS_MODULE;
 	vsc->gc.parent = vsc->dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/vitesse-vsc73xx-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/vitesse-vsc73xx-spi.c
@@ -207,10 +207,20 @@
 };
 MODULE_DEVICE_TABLE(of, vsc73xx_of_match);
 
+static const struct spi_device_id vsc73xx_spi_ids[] = {
+	{ "vsc7385" },
+	{ "vsc7388" },
+	{ "vsc7395" },
+	{ "vsc7398" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, vsc73xx_spi_ids);
+
 static struct spi_driver vsc73xx_spi_driver = {
 	.probe = vsc73xx_spi_probe,
 	.remove = vsc73xx_spi_remove,
 	.shutdown = vsc73xx_spi_shutdown,
+	.id_table = vsc73xx_spi_ids,
 	.driver = {
 		.name = "vsc73xx-spi",
 		.of_match_table = vsc73xx_of_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/dsa/xrs700x/xrs700x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/dsa/xrs700x/xrs700x.c
@@ -108,6 +108,7 @@
 {
 	struct xrs700x_port *p = &priv->ports[port];
 	struct rtnl_link_stats64 stats;
+	unsigned long flags;
 	int i;
 
 	memset(&stats, 0, sizeof(stats));
@@ -137,9 +138,9 @@
 	 */
 	stats.rx_packets += stats.multicast;
 
-	u64_stats_update_begin(&p->syncp);
+	flags = u64_stats_update_begin_irqsave(&p->syncp);
 	p->stats64 = stats;
-	u64_stats_update_end(&p->syncp);
+	u64_stats_update_end_irqrestore(&p->syncp, flags);
 
 	mutex_unlock(&p->mib_mutex);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/3com/3c589_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/3com/3c589_cs.c
@@ -195,6 +195,7 @@
 {
 	struct el3_private *lp;
 	struct net_device *dev;
+	int ret;
 
 	dev_dbg(&link->dev, "3c589_attach()\n");
 
@@ -218,7 +219,15 @@
 
 	dev->ethtool_ops = &netdev_ethtool_ops;
 
-	return tc589_config(link);
+	ret = tc589_config(link);
+	if (ret)
+		goto err_free_netdev;
+
+	return 0;
+
+err_free_netdev:
+	free_netdev(dev);
+	return ret;
 }
 
 static void tc589_detach(struct pcmcia_device *link)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/8390/mcf8390.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/8390/mcf8390.c
@@ -406,12 +406,12 @@
 static int mcf8390_probe(struct platform_device *pdev)
 {
 	struct net_device *dev;
-	struct resource *mem, *irq;
+	struct resource *mem;
 	resource_size_t msize;
-	int ret;
+	int ret, irq;
 
-	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (irq == NULL) {
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
 		dev_err(&pdev->dev, "no IRQ specified?\n");
 		return -ENXIO;
 	}
@@ -434,7 +434,7 @@
 	SET_NETDEV_DEV(dev, &pdev->dev);
 	platform_set_drvdata(pdev, dev);
 
-	dev->irq = irq->start;
+	dev->irq = irq;
 	dev->base_addr = mem->start;
 
 	ret = mcf8390_init(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/Kconfig
@@ -34,15 +34,6 @@
 source "drivers/net/ethernet/aquantia/Kconfig"
 source "drivers/net/ethernet/arc/Kconfig"
 source "drivers/net/ethernet/atheros/Kconfig"
-source "drivers/net/ethernet/broadcom/Kconfig"
-source "drivers/net/ethernet/brocade/Kconfig"
-source "drivers/net/ethernet/cadence/Kconfig"
-source "drivers/net/ethernet/calxeda/Kconfig"
-source "drivers/net/ethernet/cavium/Kconfig"
-source "drivers/net/ethernet/chelsio/Kconfig"
-source "drivers/net/ethernet/cirrus/Kconfig"
-source "drivers/net/ethernet/cisco/Kconfig"
-source "drivers/net/ethernet/cortina/Kconfig"
 
 config CX_ECAT
 	tristate "Beckhoff CX5020 EtherCAT master support"
@@ -56,6 +47,14 @@
 	  To compile this driver as a module, choose M here. The module
 	  will be called ec_bhf.
 
+source "drivers/net/ethernet/broadcom/Kconfig"
+source "drivers/net/ethernet/cadence/Kconfig"
+source "drivers/net/ethernet/calxeda/Kconfig"
+source "drivers/net/ethernet/cavium/Kconfig"
+source "drivers/net/ethernet/chelsio/Kconfig"
+source "drivers/net/ethernet/cirrus/Kconfig"
+source "drivers/net/ethernet/cisco/Kconfig"
+source "drivers/net/ethernet/cortina/Kconfig"
 source "drivers/net/ethernet/davicom/Kconfig"
 
 config DNET
@@ -82,7 +81,6 @@
 source "drivers/net/ethernet/i825xx/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
-source "drivers/net/ethernet/microsoft/Kconfig"
 source "drivers/net/ethernet/xscale/Kconfig"
 
 config JME
@@ -125,8 +123,9 @@
 source "drivers/net/ethernet/mellanox/Kconfig"
 source "drivers/net/ethernet/micrel/Kconfig"
 source "drivers/net/ethernet/microchip/Kconfig"
-source "drivers/net/ethernet/moxa/Kconfig"
 source "drivers/net/ethernet/mscc/Kconfig"
+source "drivers/net/ethernet/microsoft/Kconfig"
+source "drivers/net/ethernet/moxa/Kconfig"
 source "drivers/net/ethernet/myricom/Kconfig"
 
 config FEALNX
@@ -138,10 +137,10 @@
 	  Say Y here to support the Myson MTD-800 family of PCI-based Ethernet
 	  cards. <http://www.myson.com.tw/>
 
+source "drivers/net/ethernet/ni/Kconfig"
 source "drivers/net/ethernet/natsemi/Kconfig"
 source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/netronome/Kconfig"
-source "drivers/net/ethernet/ni/Kconfig"
 source "drivers/net/ethernet/8390/Kconfig"
 source "drivers/net/ethernet/nvidia/Kconfig"
 source "drivers/net/ethernet/nxp/Kconfig"
@@ -161,6 +160,7 @@
 source "drivers/net/ethernet/pasemi/Kconfig"
 source "drivers/net/ethernet/pensando/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
+source "drivers/net/ethernet/brocade/Kconfig"
 source "drivers/net/ethernet/qualcomm/Kconfig"
 source "drivers/net/ethernet/rdc/Kconfig"
 source "drivers/net/ethernet/realtek/Kconfig"
@@ -168,10 +168,10 @@
 source "drivers/net/ethernet/rocker/Kconfig"
 source "drivers/net/ethernet/samsung/Kconfig"
 source "drivers/net/ethernet/seeq/Kconfig"
-source "drivers/net/ethernet/sfc/Kconfig"
 source "drivers/net/ethernet/sgi/Kconfig"
 source "drivers/net/ethernet/silan/Kconfig"
 source "drivers/net/ethernet/sis/Kconfig"
+source "drivers/net/ethernet/sfc/Kconfig"
 source "drivers/net/ethernet/smsc/Kconfig"
 source "drivers/net/ethernet/socionext/Kconfig"
 source "drivers/net/ethernet/stmicro/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/actions/owl-emac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/actions/owl-emac.c
@@ -342,7 +342,7 @@
 static void owl_emac_set_hw_mac_addr(struct net_device *netdev)
 {
 	struct owl_emac_priv *priv = netdev_priv(netdev);
-	u8 *mac_addr = netdev->dev_addr;
+	const u8 *mac_addr = netdev->dev_addr;
 	u32 addr_high, addr_low;
 
 	addr_high = mac_addr[0] << 8 | mac_addr[1];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/adaptec/starfire.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/adaptec/starfire.c
@@ -955,7 +955,7 @@
 	writew(0, ioaddr + PerfFilterTable + 4);
 	writew(0, ioaddr + PerfFilterTable + 8);
 	for (i = 1; i < 16; i++) {
-		__be16 *eaddrs = (__be16 *)dev->dev_addr;
+		const __be16 *eaddrs = (const __be16 *)dev->dev_addr;
 		void __iomem *setup_frm = ioaddr + PerfFilterTable + i * 16;
 		writew(be16_to_cpu(eaddrs[2]), setup_frm); setup_frm += 4;
 		writew(be16_to_cpu(eaddrs[1]), setup_frm); setup_frm += 4;
@@ -1787,14 +1787,14 @@
 	} else if (netdev_mc_count(dev) <= 14) {
 		/* Use the 16 element perfect filter, skip first two entries. */
 		void __iomem *filter_addr = ioaddr + PerfFilterTable + 2 * 16;
-		__be16 *eaddrs;
+		const __be16 *eaddrs;
 		netdev_for_each_mc_addr(ha, dev) {
 			eaddrs = (__be16 *) ha->addr;
 			writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 4;
 			writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
 			writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 8;
 		}
-		eaddrs = (__be16 *)dev->dev_addr;
+		eaddrs = (const __be16 *)dev->dev_addr;
 		i = netdev_mc_count(dev) + 2;
 		while (i++ < 16) {
 			writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 4;
@@ -1805,7 +1805,7 @@
 	} else {
 		/* Must use a multicast hash table. */
 		void __iomem *filter_addr;
-		__be16 *eaddrs;
+		const __be16 *eaddrs;
 		__le16 mc_filter[32] __attribute__ ((aligned(sizeof(long))));	/* Multicast hash filter */
 
 		memset(mc_filter, 0, sizeof(mc_filter));
@@ -1819,7 +1819,7 @@
 		}
 		/* Clear the perfect filter list, skip first two entries. */
 		filter_addr = ioaddr + PerfFilterTable + 2 * 16;
-		eaddrs = (__be16 *)dev->dev_addr;
+		eaddrs = (const __be16 *)dev->dev_addr;
 		for (i = 2; i < 16; i++) {
 			writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 4;
 			writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aeroflex/greth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aeroflex/greth.c
@@ -258,6 +258,7 @@
 			if (dma_mapping_error(greth->dev, dma_addr)) {
 				if (netif_msg_ifup(greth))
 					dev_err(greth->dev, "Could not create initial DMA mapping\n");
+				dev_kfree_skb(skb);
 				goto cleanup;
 			}
 			greth->rx_skbuff[i] = skb;
@@ -483,7 +484,7 @@
 
 	if (unlikely(skb->len > MAX_FRAME_SIZE)) {
 		dev->stats.tx_errors++;
-		goto out;
+		goto len_error;
 	}
 
 	/* Save skb pointer. */
@@ -574,6 +575,7 @@
 map_error:
 	if (net_ratelimit())
 		dev_warn(greth->dev, "Could not create TX DMA mapping\n");
+len_error:
 	dev_kfree_skb(skb);
 out:
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/agere/et131x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/agere/et131x.c
@@ -3863,7 +3863,7 @@
 
 	et131x_init_send(adapter);
 	et131x_hwaddr_init(adapter);
-	ether_addr_copy(netdev->dev_addr, adapter->addr);
+	eth_hw_addr_set(netdev, adapter->addr);
 
 	/* Init the device with the new settings */
 	et131x_adapter_setup(adapter);
@@ -3966,7 +3966,7 @@
 
 	netif_napi_add(netdev, &adapter->napi, et131x_poll, 64);
 
-	ether_addr_copy(netdev->dev_addr, adapter->addr);
+	eth_hw_addr_set(netdev, adapter->addr);
 
 	rc = -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/alacritech/slicoss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/alacritech/slicoss.c
@@ -1008,7 +1008,7 @@
 
 static void slic_set_mac_address(struct slic_device *sdev)
 {
-	u8 *addr = sdev->netdev->dev_addr;
+	const u8 *addr = sdev->netdev->dev_addr;
 	u32 val;
 
 	val = addr[5] | addr[4] << 8 | addr[3] << 16 | addr[2] << 24;
@@ -1660,7 +1660,7 @@
 		goto free_eeprom;
 	}
 	/* set mac address */
-	ether_addr_copy(sdev->netdev->dev_addr, mac[devfn]);
+	eth_hw_addr_set(sdev->netdev, mac[devfn]);
 free_eeprom:
 	dma_free_coherent(&sdev->pdev->dev, SLIC_EEPROM_SIZE, eeprom, paddr);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/allwinner/sun4i-emac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/allwinner/sun4i-emac.c
@@ -852,7 +852,7 @@
 	}
 
 	/* Read MAC-address from DT */
-	ret = of_get_mac_address(np, ndev->dev_addr);
+	ret = of_get_ethdev_address(np, ndev);
 	if (ret) {
 		/* if the MAC address is invalid get a random one */
 		eth_hw_addr_random(ndev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/alteon/acenic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/alteon/acenic.c
@@ -2712,7 +2712,7 @@
 	struct ace_private *ap = netdev_priv(dev);
 	struct ace_regs __iomem *regs = ap->regs;
 	struct sockaddr *addr=p;
-	u8 *da;
+	const u8 *da;
 	struct cmd cmd;
 
 	if(netif_running(dev))
@@ -2720,7 +2720,7 @@
 
 	memcpy(dev->dev_addr, addr->sa_data,dev->addr_len);
 
-	da = (u8 *)dev->dev_addr;
+	da = (const u8 *)dev->dev_addr;
 
 	writel(da[0] << 8 | da[1], &regs->MacAddrHi);
 	writel((da[2] << 24) | (da[3] << 16) | (da[4] << 8) | da[5],
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/altera/altera_tse_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/altera/altera_tse_main.c
@@ -163,7 +163,8 @@
 	mdio = mdiobus_alloc();
 	if (mdio == NULL) {
 		netdev_err(dev, "Error allocating MDIO bus\n");
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto put_node;
 	}
 
 	mdio->name = ALTERA_TSE_RESOURCE_NAME;
@@ -180,6 +181,7 @@
 			   mdio->id);
 		goto out_free_mdio;
 	}
+	of_node_put(mdio_node);
 
 	if (netif_msg_drv(priv))
 		netdev_info(dev, "MDIO bus %s: created\n", mdio->id);
@@ -189,6 +191,8 @@
 out_free_mdio:
 	mdiobus_free(mdio);
 	mdio = NULL;
+put_node:
+	of_node_put(mdio_node);
 	return ret;
 }
 
@@ -849,7 +853,7 @@
 	return 0;
 }
 
-static void tse_update_mac_addr(struct altera_tse_private *priv, u8 *addr)
+static void tse_update_mac_addr(struct altera_tse_private *priv, const u8 *addr)
 {
 	u32 msb;
 	u32 lsb;
@@ -1430,16 +1434,19 @@
 		priv->rxdescmem_busaddr = dma_res->start;
 
 	} else {
+		ret = -ENODEV;
 		goto err_free_netdev;
 	}
 
-	if (!dma_set_mask(priv->device, DMA_BIT_MASK(priv->dmaops->dmamask)))
+	if (!dma_set_mask(priv->device, DMA_BIT_MASK(priv->dmaops->dmamask))) {
 		dma_set_coherent_mask(priv->device,
 				      DMA_BIT_MASK(priv->dmaops->dmamask));
-	else if (!dma_set_mask(priv->device, DMA_BIT_MASK(32)))
+	} else if (!dma_set_mask(priv->device, DMA_BIT_MASK(32))) {
 		dma_set_coherent_mask(priv->device, DMA_BIT_MASK(32));
-	else
+	} else {
+		ret = -EIO;
 		goto err_free_netdev;
+	}
 
 	/* MAC address space */
 	ret = request_and_map(pdev, "control_port", &control_port,
@@ -1524,7 +1531,7 @@
 	priv->rx_dma_buf_sz = ALTERA_RXDMABUFFER_SIZE;
 
 	/* get default MAC address from device tree */
-	ret = of_get_mac_address(pdev->dev.of_node, ndev->dev_addr);
+	ret = of_get_ethdev_address(pdev->dev.of_node, ndev);
 	if (ret)
 		eth_hw_addr_random(ndev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_admin_defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_admin_defs.h
@@ -48,6 +48,11 @@
 	ENA_ADMIN_FEATURES_OPCODE_NUM               = 32,
 };
 
+/* device capabilities */
+enum ena_admin_aq_caps_id {
+	ENA_ADMIN_ENI_STATS                         = 0,
+};
+
 enum ena_admin_placement_policy_type {
 	/* descriptors and headers are in host memory */
 	ENA_ADMIN_PLACEMENT_POLICY_HOST             = 1,
@@ -455,7 +460,10 @@
 	 */
 	u32 supported_features;
 
-	u32 reserved3;
+	/* bitmap of ena_admin_aq_caps_id, which represents device
+	 * capabilities.
+	 */
+	u32 capabilities;
 
 	/* Indicates how many bits are used physical address access. */
 	u32 phys_addr_width;
@@ -861,7 +869,9 @@
 	 * 2 : interrupt_moderation
 	 * 3 : rx_buf_mirroring
 	 * 4 : rss_configurable_function_key
-	 * 31:5 : reserved
+	 * 5 : reserved
+	 * 6 : rx_page_reuse
+	 * 31:7 : reserved
 	 */
 	u32 driver_supported_features;
 };
@@ -1176,6 +1186,8 @@
 #define ENA_ADMIN_HOST_INFO_RX_BUF_MIRRORING_MASK           BIT(3)
 #define ENA_ADMIN_HOST_INFO_RSS_CONFIGURABLE_FUNCTION_KEY_SHIFT 4
 #define ENA_ADMIN_HOST_INFO_RSS_CONFIGURABLE_FUNCTION_KEY_MASK BIT(4)
+#define ENA_ADMIN_HOST_INFO_RX_PAGE_REUSE_SHIFT             6
+#define ENA_ADMIN_HOST_INFO_RX_PAGE_REUSE_MASK              BIT(6)
 
 /* aenq_common_desc */
 #define ENA_ADMIN_AENQ_COMMON_DESC_PHASE_MASK               BIT(0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_com.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_com.c
@@ -35,6 +35,8 @@
 
 #define ENA_REGS_ADMIN_INTR_MASK 1
 
+#define ENA_MAX_BACKOFF_DELAY_EXP 16U
+
 #define ENA_MIN_ADMIN_POLL_US 100
 
 #define ENA_MAX_ADMIN_POLL_US 5000
@@ -88,8 +90,7 @@
 	struct ena_com_admin_sq *sq = &admin_queue->sq;
 	u16 size = ADMIN_SQ_SIZE(admin_queue->q_depth);
 
-	sq->entries = dma_alloc_coherent(admin_queue->q_dmadev, size,
-					 &sq->dma_addr, GFP_KERNEL);
+	sq->entries = dma_alloc_coherent(admin_queue->q_dmadev, size, &sq->dma_addr, GFP_KERNEL);
 
 	if (!sq->entries) {
 		netdev_err(ena_dev->net_device, "Memory allocation failed\n");
@@ -111,8 +112,7 @@
 	struct ena_com_admin_cq *cq = &admin_queue->cq;
 	u16 size = ADMIN_CQ_SIZE(admin_queue->q_depth);
 
-	cq->entries = dma_alloc_coherent(admin_queue->q_dmadev, size,
-					 &cq->dma_addr, GFP_KERNEL);
+	cq->entries = dma_alloc_coherent(admin_queue->q_dmadev, size, &cq->dma_addr, GFP_KERNEL);
 
 	if (!cq->entries) {
 		netdev_err(ena_dev->net_device, "Memory allocation failed\n");
@@ -134,8 +134,7 @@
 
 	ena_dev->aenq.q_depth = ENA_ASYNC_QUEUE_DEPTH;
 	size = ADMIN_AENQ_SIZE(ENA_ASYNC_QUEUE_DEPTH);
-	aenq->entries = dma_alloc_coherent(ena_dev->dmadev, size,
-					   &aenq->dma_addr, GFP_KERNEL);
+	aenq->entries = dma_alloc_coherent(ena_dev->dmadev, size, &aenq->dma_addr, GFP_KERNEL);
 
 	if (!aenq->entries) {
 		netdev_err(ena_dev->net_device, "Memory allocation failed\n");
@@ -153,14 +152,13 @@
 
 	aenq_caps = 0;
 	aenq_caps |= ena_dev->aenq.q_depth & ENA_REGS_AENQ_CAPS_AENQ_DEPTH_MASK;
-	aenq_caps |= (sizeof(struct ena_admin_aenq_entry)
-		      << ENA_REGS_AENQ_CAPS_AENQ_ENTRY_SIZE_SHIFT) &
-		     ENA_REGS_AENQ_CAPS_AENQ_ENTRY_SIZE_MASK;
+	aenq_caps |=
+		(sizeof(struct ena_admin_aenq_entry) << ENA_REGS_AENQ_CAPS_AENQ_ENTRY_SIZE_SHIFT) &
+		ENA_REGS_AENQ_CAPS_AENQ_ENTRY_SIZE_MASK;
 	writel(aenq_caps, ena_dev->reg_bar + ENA_REGS_AENQ_CAPS_OFF);
 
 	if (unlikely(!aenq_handlers)) {
-		netdev_err(ena_dev->net_device,
-			   "AENQ handlers pointer is NULL\n");
+		netdev_err(ena_dev->net_device, "AENQ handlers pointer is NULL\n");
 		return -EINVAL;
 	}
 
@@ -187,14 +185,12 @@
 	}
 
 	if (unlikely(!admin_queue->comp_ctx)) {
-		netdev_err(admin_queue->ena_dev->net_device,
-			   "Completion context is NULL\n");
+		netdev_err(admin_queue->ena_dev->net_device, "Completion context is NULL\n");
 		return NULL;
 	}
 
 	if (unlikely(admin_queue->comp_ctx[command_id].occupied && capture)) {
-		netdev_err(admin_queue->ena_dev->net_device,
-			   "Completion context is occupied\n");
+		netdev_err(admin_queue->ena_dev->net_device, "Completion context is occupied\n");
 		return NULL;
 	}
 
@@ -224,8 +220,7 @@
 	/* In case of queue FULL */
 	cnt = (u16)atomic_read(&admin_queue->outstanding_cmds);
 	if (cnt >= admin_queue->q_depth) {
-		netdev_dbg(admin_queue->ena_dev->net_device,
-			   "Admin queue is full.\n");
+		netdev_dbg(admin_queue->ena_dev->net_device, "Admin queue is full.\n");
 		admin_queue->stats.out_of_space++;
 		return ERR_PTR(-ENOSPC);
 	}
@@ -272,8 +267,7 @@
 	struct ena_comp_ctx *comp_ctx;
 	u16 i;
 
-	admin_queue->comp_ctx =
-		devm_kzalloc(admin_queue->q_dmadev, size, GFP_KERNEL);
+	admin_queue->comp_ctx = devm_kzalloc(admin_queue->q_dmadev, size, GFP_KERNEL);
 	if (unlikely(!admin_queue->comp_ctx)) {
 		netdev_err(ena_dev->net_device, "Memory allocation failed\n");
 		return -ENOMEM;
@@ -318,7 +312,6 @@
 			      struct ena_com_io_sq *io_sq)
 {
 	size_t size;
-	int dev_node = 0;
 
 	memset(&io_sq->desc_addr, 0x0, sizeof(io_sq->desc_addr));
 
@@ -331,23 +324,17 @@
 	size = io_sq->desc_entry_size * io_sq->q_depth;
 
 	if (io_sq->mem_queue_type == ENA_ADMIN_PLACEMENT_POLICY_HOST) {
-		dev_node = dev_to_node(ena_dev->dmadev);
-		set_dev_node(ena_dev->dmadev, ctx->numa_node);
 		io_sq->desc_addr.virt_addr =
-			dma_alloc_coherent(ena_dev->dmadev, size,
-					   &io_sq->desc_addr.phys_addr,
+			dma_alloc_coherent(ena_dev->dmadev, size, &io_sq->desc_addr.phys_addr,
 					   GFP_KERNEL);
-		set_dev_node(ena_dev->dmadev, dev_node);
 		if (!io_sq->desc_addr.virt_addr) {
 			io_sq->desc_addr.virt_addr =
 				dma_alloc_coherent(ena_dev->dmadev, size,
-						   &io_sq->desc_addr.phys_addr,
-						   GFP_KERNEL);
+						   &io_sq->desc_addr.phys_addr, GFP_KERNEL);
 		}
 
 		if (!io_sq->desc_addr.virt_addr) {
-			netdev_err(ena_dev->net_device,
-				   "Memory allocation failed\n");
+			netdev_err(ena_dev->net_device, "Memory allocation failed\n");
 			return -ENOMEM;
 		}
 	}
@@ -360,21 +347,16 @@
 			ENA_COM_BOUNCE_BUFFER_CNTRL_CNT;
 		io_sq->bounce_buf_ctrl.next_to_use = 0;
 
-		size = io_sq->bounce_buf_ctrl.buffer_size *
+		size = (size_t)io_sq->bounce_buf_ctrl.buffer_size *
 			io_sq->bounce_buf_ctrl.buffers_num;
 
-		dev_node = dev_to_node(ena_dev->dmadev);
-		set_dev_node(ena_dev->dmadev, ctx->numa_node);
-		io_sq->bounce_buf_ctrl.base_buffer =
-			devm_kzalloc(ena_dev->dmadev, size, GFP_KERNEL);
-		set_dev_node(ena_dev->dmadev, dev_node);
+		io_sq->bounce_buf_ctrl.base_buffer = devm_kzalloc(ena_dev->dmadev, size, GFP_KERNEL);
 		if (!io_sq->bounce_buf_ctrl.base_buffer)
 			io_sq->bounce_buf_ctrl.base_buffer =
 				devm_kzalloc(ena_dev->dmadev, size, GFP_KERNEL);
 
 		if (!io_sq->bounce_buf_ctrl.base_buffer) {
-			netdev_err(ena_dev->net_device,
-				   "Bounce buffer memory allocation failed\n");
+			netdev_err(ena_dev->net_device, "Bounce buffer memory allocation failed\n");
 			return -ENOMEM;
 		}
 
@@ -408,7 +390,6 @@
 			      struct ena_com_io_cq *io_cq)
 {
 	size_t size;
-	int prev_node = 0;
 
 	memset(&io_cq->cdesc_addr, 0x0, sizeof(io_cq->cdesc_addr));
 
@@ -420,16 +401,11 @@
 
 	size = io_cq->cdesc_entry_size_in_bytes * io_cq->q_depth;
 
-	prev_node = dev_to_node(ena_dev->dmadev);
-	set_dev_node(ena_dev->dmadev, ctx->numa_node);
 	io_cq->cdesc_addr.virt_addr =
-		dma_alloc_coherent(ena_dev->dmadev, size,
-				   &io_cq->cdesc_addr.phys_addr, GFP_KERNEL);
-	set_dev_node(ena_dev->dmadev, prev_node);
+		dma_alloc_coherent(ena_dev->dmadev, size, &io_cq->cdesc_addr.phys_addr, GFP_KERNEL);
 	if (!io_cq->cdesc_addr.virt_addr) {
 		io_cq->cdesc_addr.virt_addr =
-			dma_alloc_coherent(ena_dev->dmadev, size,
-					   &io_cq->cdesc_addr.phys_addr,
+			dma_alloc_coherent(ena_dev->dmadev, size, &io_cq->cdesc_addr.phys_addr,
 					   GFP_KERNEL);
 	}
 
@@ -512,8 +488,8 @@
 					u8 comp_status)
 {
 	if (unlikely(comp_status != 0))
-		netdev_err(admin_queue->ena_dev->net_device,
-			   "Admin command failed[%u]\n", comp_status);
+		netdev_err(admin_queue->ena_dev->net_device, "Admin command failed[%u]\n",
+			   comp_status);
 
 	switch (comp_status) {
 	case ENA_ADMIN_SUCCESS:
@@ -536,6 +512,7 @@
 
 static void ena_delay_exponential_backoff_us(u32 exp, u32 delay_us)
 {
+	exp = min_t(u32, exp, ENA_MAX_BACKOFF_DELAY_EXP);
 	delay_us = max_t(u32, ENA_MIN_ADMIN_POLL_US, delay_us);
 	delay_us = min_t(u32, delay_us * (1U << exp), ENA_MAX_ADMIN_POLL_US);
 	usleep_range(delay_us, 2 * delay_us);
@@ -577,8 +554,7 @@
 	}
 
 	if (unlikely(comp_ctx->status == ENA_CMD_ABORTED)) {
-		netdev_err(admin_queue->ena_dev->net_device,
-			   "Command was aborted\n");
+		netdev_err(admin_queue->ena_dev->net_device, "Command was aborted\n");
 		spin_lock_irqsave(&admin_queue->q_lock, flags);
 		admin_queue->stats.aborted_cmd++;
 		spin_unlock_irqrestore(&admin_queue->q_lock, flags);
@@ -586,8 +562,7 @@
 		goto err;
 	}
 
-	WARN(comp_ctx->status != ENA_CMD_COMPLETED, "Invalid comp status %d\n",
-	     comp_ctx->status);
+	WARN(comp_ctx->status != ENA_CMD_COMPLETED, "Invalid comp status %d\n", comp_ctx->status);
 
 	ret = ena_com_comp_status_to_errno(admin_queue, comp_ctx->comp_status);
 err:
@@ -631,8 +606,7 @@
 					    sizeof(resp));
 
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to set LLQ configurations: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to set LLQ configurations: %d\n", ret);
 
 	return ret;
 }
@@ -655,8 +629,7 @@
 			llq_default_cfg->llq_header_location;
 	} else {
 		netdev_err(ena_dev->net_device,
-			   "Invalid header location control, supported: 0x%x\n",
-			   supported_feat);
+			   "Invalid header location control, supported: 0x%x\n", supported_feat);
 		return -EINVAL;
 	}
 
@@ -678,8 +651,8 @@
 
 			netdev_err(ena_dev->net_device,
 				   "Default llq stride ctrl is not supported, performing fallback, default: 0x%x, supported: 0x%x, used: 0x%x\n",
-				   llq_default_cfg->llq_stride_ctrl,
-				   supported_feat, llq_info->desc_stride_ctrl);
+				   llq_default_cfg->llq_stride_ctrl, supported_feat,
+				   llq_info->desc_stride_ctrl);
 		}
 	} else {
 		llq_info->desc_stride_ctrl = 0;
@@ -701,8 +674,7 @@
 			llq_info->desc_list_entry_size = 256;
 		} else {
 			netdev_err(ena_dev->net_device,
-				   "Invalid entry_size_ctrl, supported: 0x%x\n",
-				   supported_feat);
+				   "Invalid entry_size_ctrl, supported: 0x%x\n", supported_feat);
 			return -EINVAL;
 		}
 
@@ -747,8 +719,8 @@
 
 		netdev_err(ena_dev->net_device,
 			   "Default llq num descs before header is not supported, performing fallback, default: 0x%x, supported: 0x%x, used: 0x%x\n",
-			   llq_default_cfg->llq_num_decs_before_header,
-			   supported_feat, llq_info->descs_num_before_header);
+			   llq_default_cfg->llq_num_decs_before_header, supported_feat,
+			   llq_info->descs_num_before_header);
 	}
 	/* Check for accelerated queue supported */
 	llq_accel_mode_get = llq_features->accel_mode.u.get;
@@ -764,8 +736,7 @@
 
 	rc = ena_com_set_llq(ena_dev);
 	if (rc)
-		netdev_err(ena_dev->net_device,
-			   "Cannot set LLQ configuration: %d\n", rc);
+		netdev_err(ena_dev->net_device, "Cannot set LLQ configuration: %d\n", rc);
 
 	return rc;
 }
@@ -777,8 +748,7 @@
 	int ret;
 
 	wait_for_completion_timeout(&comp_ctx->wait_event,
-				    usecs_to_jiffies(
-					    admin_queue->completion_timeout));
+				    usecs_to_jiffies(admin_queue->completion_timeout));
 
 	/* In case the command wasn't completed find out the root cause.
 	 * There might be 2 kinds of errors
@@ -794,8 +764,7 @@
 		if (comp_ctx->status == ENA_CMD_COMPLETED) {
 			netdev_err(admin_queue->ena_dev->net_device,
 				   "The ena device sent a completion but the driver didn't receive a MSI-X interrupt (cmd %d), autopolling mode is %s\n",
-				   comp_ctx->cmd_opcode,
-				   admin_queue->auto_polling ? "ON" : "OFF");
+				   comp_ctx->cmd_opcode, admin_queue->auto_polling ? "ON" : "OFF");
 			/* Check if fallback to polling is enabled */
 			if (admin_queue->auto_polling)
 				admin_queue->polling = true;
@@ -864,15 +833,13 @@
 	if (unlikely(i == timeout)) {
 		netdev_err(ena_dev->net_device,
 			   "Reading reg failed for timeout. expected: req id[%u] offset[%u] actual: req id[%u] offset[%u]\n",
-			   mmio_read->seq_num, offset, read_resp->req_id,
-			   read_resp->reg_off);
+			   mmio_read->seq_num, offset, read_resp->req_id, read_resp->reg_off);
 		ret = ENA_MMIO_READ_TIMEOUT;
 		goto err;
 	}
 
 	if (read_resp->reg_off != offset) {
-		netdev_err(ena_dev->net_device,
-			   "Read failure: wrong offset provided\n");
+		netdev_err(ena_dev->net_device, "Read failure: wrong offset provided\n");
 		ret = ENA_MMIO_READ_TIMEOUT;
 	} else {
 		ret = read_resp->reg_val;
@@ -931,8 +898,7 @@
 					    sizeof(destroy_resp));
 
 	if (unlikely(ret && (ret != -ENODEV)))
-		netdev_err(ena_dev->net_device,
-			   "Failed to destroy io sq error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to destroy io sq error: %d\n", ret);
 
 	return ret;
 }
@@ -946,8 +912,7 @@
 	if (io_cq->cdesc_addr.virt_addr) {
 		size = io_cq->cdesc_entry_size_in_bytes * io_cq->q_depth;
 
-		dma_free_coherent(ena_dev->dmadev, size,
-				  io_cq->cdesc_addr.virt_addr,
+		dma_free_coherent(ena_dev->dmadev, size, io_cq->cdesc_addr.virt_addr,
 				  io_cq->cdesc_addr.phys_addr);
 
 		io_cq->cdesc_addr.virt_addr = NULL;
@@ -956,8 +921,7 @@
 	if (io_sq->desc_addr.virt_addr) {
 		size = io_sq->desc_entry_size * io_sq->q_depth;
 
-		dma_free_coherent(ena_dev->dmadev, size,
-				  io_sq->desc_addr.virt_addr,
+		dma_free_coherent(ena_dev->dmadev, size, io_sq->desc_addr.virt_addr,
 				  io_sq->desc_addr.phys_addr);
 
 		io_sq->desc_addr.virt_addr = NULL;
@@ -982,8 +946,7 @@
 		val = ena_com_reg_bar_read32(ena_dev, ENA_REGS_DEV_STS_OFF);
 
 		if (unlikely(val == ENA_MMIO_READ_TIMEOUT)) {
-			netdev_err(ena_dev->net_device,
-				   "Reg read timeout occurred\n");
+			netdev_err(ena_dev->net_device, "Reg read timeout occurred\n");
 			return -ETIME;
 		}
 
@@ -1023,8 +986,7 @@
 	int ret;
 
 	if (!ena_com_check_supported_feature_id(ena_dev, feature_id)) {
-		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n",
-			   feature_id);
+		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n", feature_id);
 		return -EOPNOTSUPP;
 	}
 
@@ -1061,8 +1023,7 @@
 
 	if (unlikely(ret))
 		netdev_err(ena_dev->net_device,
-			   "Failed to submit get_feature command %d error: %d\n",
-			   feature_id, ret);
+			   "Failed to submit get_feature command %d error: %d\n", feature_id, ret);
 
 	return ret;
 }
@@ -1101,13 +1062,11 @@
 {
 	struct ena_rss *rss = &ena_dev->rss;
 
-	if (!ena_com_check_supported_feature_id(ena_dev,
-						ENA_ADMIN_RSS_HASH_FUNCTION))
+	if (!ena_com_check_supported_feature_id(ena_dev, ENA_ADMIN_RSS_HASH_FUNCTION))
 		return -EOPNOTSUPP;
 
-	rss->hash_key =
-		dma_alloc_coherent(ena_dev->dmadev, sizeof(*rss->hash_key),
-				   &rss->hash_key_dma_addr, GFP_KERNEL);
+	rss->hash_key = dma_alloc_coherent(ena_dev->dmadev, sizeof(*rss->hash_key),
+					   &rss->hash_key_dma_addr, GFP_KERNEL);
 
 	if (unlikely(!rss->hash_key))
 		return -ENOMEM;
@@ -1120,8 +1079,8 @@
 	struct ena_rss *rss = &ena_dev->rss;
 
 	if (rss->hash_key)
-		dma_free_coherent(ena_dev->dmadev, sizeof(*rss->hash_key),
-				  rss->hash_key, rss->hash_key_dma_addr);
+		dma_free_coherent(ena_dev->dmadev, sizeof(*rss->hash_key), rss->hash_key,
+				  rss->hash_key_dma_addr);
 	rss->hash_key = NULL;
 }
 
@@ -1129,9 +1088,8 @@
 {
 	struct ena_rss *rss = &ena_dev->rss;
 
-	rss->hash_ctrl =
-		dma_alloc_coherent(ena_dev->dmadev, sizeof(*rss->hash_ctrl),
-				   &rss->hash_ctrl_dma_addr, GFP_KERNEL);
+	rss->hash_ctrl = dma_alloc_coherent(ena_dev->dmadev, sizeof(*rss->hash_ctrl),
+					    &rss->hash_ctrl_dma_addr, GFP_KERNEL);
 
 	if (unlikely(!rss->hash_ctrl))
 		return -ENOMEM;
@@ -1144,8 +1102,8 @@
 	struct ena_rss *rss = &ena_dev->rss;
 
 	if (rss->hash_ctrl)
-		dma_free_coherent(ena_dev->dmadev, sizeof(*rss->hash_ctrl),
-				  rss->hash_ctrl, rss->hash_ctrl_dma_addr);
+		dma_free_coherent(ena_dev->dmadev, sizeof(*rss->hash_ctrl), rss->hash_ctrl,
+				  rss->hash_ctrl_dma_addr);
 	rss->hash_ctrl = NULL;
 }
 
@@ -1174,15 +1132,13 @@
 	tbl_size = (1ULL << log_size) *
 		sizeof(struct ena_admin_rss_ind_table_entry);
 
-	rss->rss_ind_tbl =
-		dma_alloc_coherent(ena_dev->dmadev, tbl_size,
-				   &rss->rss_ind_tbl_dma_addr, GFP_KERNEL);
+	rss->rss_ind_tbl = dma_alloc_coherent(ena_dev->dmadev, tbl_size, &rss->rss_ind_tbl_dma_addr,
+					      GFP_KERNEL);
 	if (unlikely(!rss->rss_ind_tbl))
 		goto mem_err1;
 
 	tbl_size = (1ULL << log_size) * sizeof(u16);
-	rss->host_rss_ind_tbl =
-		devm_kzalloc(ena_dev->dmadev, tbl_size, GFP_KERNEL);
+	rss->host_rss_ind_tbl = devm_kzalloc(ena_dev->dmadev, tbl_size, GFP_KERNEL);
 	if (unlikely(!rss->host_rss_ind_tbl))
 		goto mem_err2;
 
@@ -1194,8 +1150,7 @@
 	tbl_size = (1ULL << log_size) *
 		sizeof(struct ena_admin_rss_ind_table_entry);
 
-	dma_free_coherent(ena_dev->dmadev, tbl_size, rss->rss_ind_tbl,
-			  rss->rss_ind_tbl_dma_addr);
+	dma_free_coherent(ena_dev->dmadev, tbl_size, rss->rss_ind_tbl, rss->rss_ind_tbl_dma_addr);
 	rss->rss_ind_tbl = NULL;
 mem_err1:
 	rss->tbl_log_size = 0;
@@ -1258,8 +1213,7 @@
 					   &create_cmd.sq_ba,
 					   io_sq->desc_addr.phys_addr);
 		if (unlikely(ret)) {
-			netdev_err(ena_dev->net_device,
-				   "Memory address set failed\n");
+			netdev_err(ena_dev->net_device, "Memory address set failed\n");
 			return ret;
 		}
 	}
@@ -1270,8 +1224,7 @@
 					    (struct ena_admin_acq_entry *)&cmd_completion,
 					    sizeof(cmd_completion));
 	if (unlikely(ret)) {
-		netdev_err(ena_dev->net_device,
-			   "Failed to create IO SQ. error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to create IO SQ. error: %d\n", ret);
 		return ret;
 	}
 
@@ -1289,8 +1242,7 @@
 			cmd_completion.llq_descriptors_offset);
 	}
 
-	netdev_dbg(ena_dev->net_device, "Created sq[%u], depth[%u]\n",
-		   io_sq->idx, io_sq->q_depth);
+	netdev_dbg(ena_dev->net_device, "Created sq[%u], depth[%u]\n", io_sq->idx, io_sq->q_depth);
 
 	return ret;
 }
@@ -1417,8 +1369,7 @@
 					    (struct ena_admin_acq_entry *)&cmd_completion,
 					    sizeof(cmd_completion));
 	if (unlikely(ret)) {
-		netdev_err(ena_dev->net_device,
-			   "Failed to create IO CQ. error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to create IO CQ. error: %d\n", ret);
 		return ret;
 	}
 
@@ -1437,8 +1388,7 @@
 			(u32 __iomem *)((uintptr_t)ena_dev->reg_bar +
 			cmd_completion.numa_node_register_offset);
 
-	netdev_dbg(ena_dev->net_device, "Created cq[%u], depth[%u]\n",
-		   io_cq->idx, io_cq->q_depth);
+	netdev_dbg(ena_dev->net_device, "Created cq[%u], depth[%u]\n", io_cq->idx, io_cq->q_depth);
 
 	return ret;
 }
@@ -1448,8 +1398,7 @@
 			    struct ena_com_io_cq **io_cq)
 {
 	if (qid >= ENA_TOTAL_NUM_QUEUES) {
-		netdev_err(ena_dev->net_device,
-			   "Invalid queue number %d but the max is %d\n", qid,
+		netdev_err(ena_dev->net_device, "Invalid queue number %d but the max is %d\n", qid,
 			   ENA_TOTAL_NUM_QUEUES);
 		return -EINVAL;
 	}
@@ -1489,8 +1438,7 @@
 	spin_lock_irqsave(&admin_queue->q_lock, flags);
 	while (atomic_read(&admin_queue->outstanding_cmds) != 0) {
 		spin_unlock_irqrestore(&admin_queue->q_lock, flags);
-		ena_delay_exponential_backoff_us(exp++,
-						 ena_dev->ena_min_poll_delay_us);
+		ena_delay_exponential_backoff_us(exp++, ena_dev->ena_min_poll_delay_us);
 		spin_lock_irqsave(&admin_queue->q_lock, flags);
 	}
 	spin_unlock_irqrestore(&admin_queue->q_lock, flags);
@@ -1516,8 +1464,7 @@
 					    sizeof(destroy_resp));
 
 	if (unlikely(ret && (ret != -ENODEV)))
-		netdev_err(ena_dev->net_device,
-			   "Failed to destroy IO CQ. error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to destroy IO CQ. error: %d\n", ret);
 
 	return ret;
 }
@@ -1585,8 +1532,7 @@
 					    sizeof(resp));
 
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to config AENQ ret: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to config AENQ ret: %d\n", ret);
 
 	return ret;
 }
@@ -1607,8 +1553,7 @@
 	netdev_dbg(ena_dev->net_device, "ENA dma width: %d\n", width);
 
 	if ((width < 32) || width > ENA_MAX_PHYS_ADDR_SIZE_BITS) {
-		netdev_err(ena_dev->net_device, "DMA width illegal value: %d\n",
-			   width);
+		netdev_err(ena_dev->net_device, "DMA width illegal value: %d\n", width);
 		return -EINVAL;
 	}
 
@@ -1630,19 +1575,16 @@
 	ctrl_ver = ena_com_reg_bar_read32(ena_dev,
 					  ENA_REGS_CONTROLLER_VERSION_OFF);
 
-	if (unlikely((ver == ENA_MMIO_READ_TIMEOUT) ||
-		     (ctrl_ver == ENA_MMIO_READ_TIMEOUT))) {
+	if (unlikely((ver == ENA_MMIO_READ_TIMEOUT) || (ctrl_ver == ENA_MMIO_READ_TIMEOUT))) {
 		netdev_err(ena_dev->net_device, "Reg read timeout occurred\n");
 		return -ETIME;
 	}
 
 	dev_info(ena_dev->dmadev, "ENA device version: %d.%d\n",
-		 (ver & ENA_REGS_VERSION_MAJOR_VERSION_MASK) >>
-			 ENA_REGS_VERSION_MAJOR_VERSION_SHIFT,
+		 (ver & ENA_REGS_VERSION_MAJOR_VERSION_MASK) >> ENA_REGS_VERSION_MAJOR_VERSION_SHIFT,
 		 ver & ENA_REGS_VERSION_MINOR_VERSION_MASK);
 
-	dev_info(ena_dev->dmadev,
-		 "ENA controller version: %d.%d.%d implementation version %d\n",
+	dev_info(ena_dev->dmadev, "ENA controller version: %d.%d.%d implementation version %d\n",
 		 (ctrl_ver & ENA_REGS_CONTROLLER_VERSION_MAJOR_VERSION_MASK) >>
 			 ENA_REGS_CONTROLLER_VERSION_MAJOR_VERSION_SHIFT,
 		 (ctrl_ver & ENA_REGS_CONTROLLER_VERSION_MINOR_VERSION_MASK) >>
@@ -1691,20 +1633,17 @@
 
 	size = ADMIN_SQ_SIZE(admin_queue->q_depth);
 	if (sq->entries)
-		dma_free_coherent(ena_dev->dmadev, size, sq->entries,
-				  sq->dma_addr);
+		dma_free_coherent(ena_dev->dmadev, size, sq->entries, sq->dma_addr);
 	sq->entries = NULL;
 
 	size = ADMIN_CQ_SIZE(admin_queue->q_depth);
 	if (cq->entries)
-		dma_free_coherent(ena_dev->dmadev, size, cq->entries,
-				  cq->dma_addr);
+		dma_free_coherent(ena_dev->dmadev, size, cq->entries, cq->dma_addr);
 	cq->entries = NULL;
 
 	size = ADMIN_AENQ_SIZE(aenq->q_depth);
 	if (ena_dev->aenq.entries)
-		dma_free_coherent(ena_dev->dmadev, size, aenq->entries,
-				  aenq->dma_addr);
+		dma_free_coherent(ena_dev->dmadev, size, aenq->entries, aenq->dma_addr);
 	aenq->entries = NULL;
 }
 
@@ -1730,10 +1669,8 @@
 	struct ena_com_mmio_read *mmio_read = &ena_dev->mmio_read;
 
 	spin_lock_init(&mmio_read->lock);
-	mmio_read->read_resp =
-		dma_alloc_coherent(ena_dev->dmadev,
-				   sizeof(*mmio_read->read_resp),
-				   &mmio_read->read_resp_dma_addr, GFP_KERNEL);
+	mmio_read->read_resp = dma_alloc_coherent(ena_dev->dmadev, sizeof(*mmio_read->read_resp),
+						  &mmio_read->read_resp_dma_addr, GFP_KERNEL);
 	if (unlikely(!mmio_read->read_resp))
 		goto err;
 
@@ -1764,8 +1701,8 @@
 	writel(0x0, ena_dev->reg_bar + ENA_REGS_MMIO_RESP_LO_OFF);
 	writel(0x0, ena_dev->reg_bar + ENA_REGS_MMIO_RESP_HI_OFF);
 
-	dma_free_coherent(ena_dev->dmadev, sizeof(*mmio_read->read_resp),
-			  mmio_read->read_resp, mmio_read->read_resp_dma_addr);
+	dma_free_coherent(ena_dev->dmadev, sizeof(*mmio_read->read_resp), mmio_read->read_resp,
+			  mmio_read->read_resp_dma_addr);
 
 	mmio_read->read_resp = NULL;
 }
@@ -1797,8 +1734,7 @@
 	}
 
 	if (!(dev_sts & ENA_REGS_DEV_STS_READY_MASK)) {
-		netdev_err(ena_dev->net_device,
-			   "Device isn't ready, abort com init\n");
+		netdev_err(ena_dev->net_device, "Device isn't ready, abort com init\n");
 		return -ENODEV;
 	}
 
@@ -1875,8 +1811,7 @@
 	int ret;
 
 	if (ctx->qid >= ENA_TOTAL_NUM_QUEUES) {
-		netdev_err(ena_dev->net_device,
-			   "Qid (%d) is bigger than max num of queues (%d)\n",
+		netdev_err(ena_dev->net_device, "Qid (%d) is bigger than max num of queues (%d)\n",
 			   ctx->qid, ENA_TOTAL_NUM_QUEUES);
 		return -EINVAL;
 	}
@@ -1902,8 +1837,7 @@
 
 	if (ctx->direction == ENA_COM_IO_QUEUE_DIRECTION_TX)
 		/* header length is limited to 8 bits */
-		io_sq->tx_max_header_size =
-			min_t(u32, ena_dev->tx_max_header_size, SZ_256);
+		io_sq->tx_max_header_size = min_t(u32, ena_dev->tx_max_header_size, SZ_256);
 
 	ret = ena_com_init_io_sq(ena_dev, ctx, io_sq);
 	if (ret)
@@ -1935,8 +1869,7 @@
 	struct ena_com_io_cq *io_cq;
 
 	if (qid >= ENA_TOTAL_NUM_QUEUES) {
-		netdev_err(ena_dev->net_device,
-			   "Qid (%d) is bigger than max num of queues (%d)\n",
+		netdev_err(ena_dev->net_device, "Qid (%d) is bigger than max num of queues (%d)\n",
 			   qid, ENA_TOTAL_NUM_QUEUES);
 		return;
 	}
@@ -1971,6 +1904,7 @@
 	       sizeof(get_resp.u.dev_attr));
 
 	ena_dev->supported_features = get_resp.u.dev_attr.supported_features;
+	ena_dev->capabilities = get_resp.u.dev_attr.capabilities;
 
 	if (ena_dev->supported_features & BIT(ENA_ADMIN_MAX_QUEUES_EXT)) {
 		rc = ena_com_get_feature(ena_dev, &get_resp,
@@ -1979,8 +1913,7 @@
 		if (rc)
 			return rc;
 
-		if (get_resp.u.max_queue_ext.version !=
-		    ENA_FEATURE_MAX_QUEUE_EXT_VER)
+		if (get_resp.u.max_queue_ext.version != ENA_FEATURE_MAX_QUEUE_EXT_VER)
 			return -EINVAL;
 
 		memcpy(&get_feat_ctx->max_queue_ext, &get_resp.u.max_queue_ext,
@@ -2021,18 +1954,15 @@
 	rc = ena_com_get_feature(ena_dev, &get_resp, ENA_ADMIN_HW_HINTS, 0);
 
 	if (!rc)
-		memcpy(&get_feat_ctx->hw_hints, &get_resp.u.hw_hints,
-		       sizeof(get_resp.u.hw_hints));
+		memcpy(&get_feat_ctx->hw_hints, &get_resp.u.hw_hints, sizeof(get_resp.u.hw_hints));
 	else if (rc == -EOPNOTSUPP)
-		memset(&get_feat_ctx->hw_hints, 0x0,
-		       sizeof(get_feat_ctx->hw_hints));
+		memset(&get_feat_ctx->hw_hints, 0x0, sizeof(get_feat_ctx->hw_hints));
 	else
 		return rc;
 
 	rc = ena_com_get_feature(ena_dev, &get_resp, ENA_ADMIN_LLQ, 0);
 	if (!rc)
-		memcpy(&get_feat_ctx->llq, &get_resp.u.llq,
-		       sizeof(get_resp.u.llq));
+		memcpy(&get_feat_ctx->llq, &get_resp.u.llq, sizeof(get_resp.u.llq));
 	else if (rc == -EOPNOTSUPP)
 		memset(&get_feat_ctx->llq, 0x0, sizeof(get_feat_ctx->llq));
 	else
@@ -2080,8 +2010,7 @@
 	aenq_common = &aenq_e->aenq_common_desc;
 
 	/* Go over all the events */
-	while ((READ_ONCE(aenq_common->flags) &
-		ENA_ADMIN_AENQ_COMMON_DESC_PHASE_MASK) == phase) {
+	while ((READ_ONCE(aenq_common->flags) & ENA_ADMIN_AENQ_COMMON_DESC_PHASE_MASK) == phase) {
 		/* Make sure the phase bit (ownership) is as expected before
 		 * reading the rest of the descriptor.
 		 */
@@ -2090,8 +2019,7 @@
 		timestamp = (u64)aenq_common->timestamp_low |
 			((u64)aenq_common->timestamp_high << 32);
 
-		netdev_dbg(ena_dev->net_device,
-			   "AENQ! Group[%x] Syndrome[%x] timestamp: [%llus]\n",
+		netdev_dbg(ena_dev->net_device, "AENQ! Group[%x] Syndrome[%x] timestamp: [%llus]\n",
 			   aenq_common->group, aenq_common->syndrome, timestamp);
 
 		/* Handle specific event*/
@@ -2120,8 +2048,7 @@
 
 	/* write the aenq doorbell after all AENQ descriptors were read */
 	mb();
-	writel_relaxed((u32)aenq->head,
-		       ena_dev->reg_bar + ENA_REGS_AENQ_HEAD_DB_OFF);
+	writel_relaxed((u32)aenq->head, ena_dev->reg_bar + ENA_REGS_AENQ_HEAD_DB_OFF);
 }
 
 int ena_com_dev_reset(struct ena_com_dev *ena_dev,
@@ -2133,15 +2060,13 @@
 	stat = ena_com_reg_bar_read32(ena_dev, ENA_REGS_DEV_STS_OFF);
 	cap = ena_com_reg_bar_read32(ena_dev, ENA_REGS_CAPS_OFF);
 
-	if (unlikely((stat == ENA_MMIO_READ_TIMEOUT) ||
-		     (cap == ENA_MMIO_READ_TIMEOUT))) {
+	if (unlikely((stat == ENA_MMIO_READ_TIMEOUT) || (cap == ENA_MMIO_READ_TIMEOUT))) {
 		netdev_err(ena_dev->net_device, "Reg read32 timeout occurred\n");
 		return -ETIME;
 	}
 
 	if ((stat & ENA_REGS_DEV_STS_READY_MASK) == 0) {
-		netdev_err(ena_dev->net_device,
-			   "Device isn't ready, can't reset device\n");
+		netdev_err(ena_dev->net_device, "Device isn't ready, can't reset device\n");
 		return -EINVAL;
 	}
 
@@ -2164,8 +2089,7 @@
 	rc = wait_for_reset_state(ena_dev, timeout,
 				  ENA_REGS_DEV_STS_RESET_IN_PROGRESS_MASK);
 	if (rc != 0) {
-		netdev_err(ena_dev->net_device,
-			   "Reset indication didn't turn on\n");
+		netdev_err(ena_dev->net_device, "Reset indication didn't turn on\n");
 		return rc;
 	}
 
@@ -2173,8 +2097,7 @@
 	writel(0, ena_dev->reg_bar + ENA_REGS_DEV_CTL_OFF);
 	rc = wait_for_reset_state(ena_dev, timeout, 0);
 	if (rc != 0) {
-		netdev_err(ena_dev->net_device,
-			   "Reset indication didn't turn off\n");
+		netdev_err(ena_dev->net_device, "Reset indication didn't turn off\n");
 		return rc;
 	}
 
@@ -2211,8 +2134,7 @@
 					     sizeof(*get_resp));
 
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to get stats. error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to get stats. error: %d\n", ret);
 
 	return ret;
 }
@@ -2223,6 +2145,12 @@
 	struct ena_com_stats_ctx ctx;
 	int ret;
 
+	if (!ena_com_get_cap(ena_dev, ENA_ADMIN_ENI_STATS)) {
+		netdev_err(ena_dev->net_device, "Capability %d isn't supported\n",
+			   ENA_ADMIN_ENI_STATS);
+		return -EOPNOTSUPP;
+	}
+
 	memset(&ctx, 0x0, sizeof(ctx));
 	ret = ena_get_dev_stats(ena_dev, &ctx, ENA_ADMIN_GET_STATS_TYPE_ENI);
 	if (likely(ret == 0))
@@ -2255,8 +2183,7 @@
 	int ret;
 
 	if (!ena_com_check_supported_feature_id(ena_dev, ENA_ADMIN_MTU)) {
-		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n",
-			   ENA_ADMIN_MTU);
+		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n", ENA_ADMIN_MTU);
 		return -EOPNOTSUPP;
 	}
 
@@ -2275,8 +2202,7 @@
 					    sizeof(resp));
 
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to set mtu %d. error: %d\n", mtu, ret);
+		netdev_err(ena_dev->net_device, "Failed to set mtu %d. error: %d\n", mtu, ret);
 
 	return ret;
 }
@@ -2290,8 +2216,7 @@
 	ret = ena_com_get_feature(ena_dev, &resp,
 				  ENA_ADMIN_STATELESS_OFFLOAD_CONFIG, 0);
 	if (unlikely(ret)) {
-		netdev_err(ena_dev->net_device,
-			   "Failed to get offload capabilities %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to get offload capabilities %d\n", ret);
 		return ret;
 	}
 
@@ -2309,8 +2234,7 @@
 	struct ena_admin_get_feat_resp get_resp;
 	int ret;
 
-	if (!ena_com_check_supported_feature_id(ena_dev,
-						ENA_ADMIN_RSS_HASH_FUNCTION)) {
+	if (!ena_com_check_supported_feature_id(ena_dev, ENA_ADMIN_RSS_HASH_FUNCTION)) {
 		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n",
 			   ENA_ADMIN_RSS_HASH_FUNCTION);
 		return -EOPNOTSUPP;
@@ -2323,8 +2247,7 @@
 		return ret;
 
 	if (!(get_resp.u.flow_hash_func.supported_func & BIT(rss->hash_func))) {
-		netdev_err(ena_dev->net_device,
-			   "Func hash %d isn't supported by device, abort\n",
+		netdev_err(ena_dev->net_device, "Func hash %d isn't supported by device, abort\n",
 			   rss->hash_func);
 		return -EOPNOTSUPP;
 	}
@@ -2354,8 +2277,7 @@
 					    (struct ena_admin_acq_entry *)&resp,
 					    sizeof(resp));
 	if (unlikely(ret)) {
-		netdev_err(ena_dev->net_device,
-			   "Failed to set hash function %d. error: %d\n",
+		netdev_err(ena_dev->net_device, "Failed to set hash function %d. error: %d\n",
 			   rss->hash_func, ret);
 		return -EINVAL;
 	}
@@ -2387,34 +2309,22 @@
 		return rc;
 
 	if (!(BIT(func) & get_resp.u.flow_hash_func.supported_func)) {
-		netdev_err(ena_dev->net_device,
-			   "Flow hash function %d isn't supported\n", func);
+		netdev_err(ena_dev->net_device, "Flow hash function %d isn't supported\n", func);
 		return -EOPNOTSUPP;
 	}
 
-	switch (func) {
-	case ENA_ADMIN_TOEPLITZ:
-		if (key) {
-			if (key_len != sizeof(hash_key->key)) {
-				netdev_err(ena_dev->net_device,
-					   "key len (%u) doesn't equal the supported size (%zu)\n",
-					   key_len, sizeof(hash_key->key));
-				return -EINVAL;
-			}
-			memcpy(hash_key->key, key, key_len);
-			rss->hash_init_val = init_val;
-			hash_key->key_parts = key_len / sizeof(hash_key->key[0]);
+	if ((func == ENA_ADMIN_TOEPLITZ) && key) {
+		if (key_len != sizeof(hash_key->key)) {
+			netdev_err(ena_dev->net_device,
+				   "key len (%u) doesn't equal the supported size (%zu)\n", key_len,
+				   sizeof(hash_key->key));
+			return -EINVAL;
 		}
-		break;
-	case ENA_ADMIN_CRC32:
-		rss->hash_init_val = init_val;
-		break;
-	default:
-		netdev_err(ena_dev->net_device, "Invalid hash function (%d)\n",
-			   func);
-		return -EINVAL;
+		memcpy(hash_key->key, key, key_len);
+		hash_key->key_parts = key_len / sizeof(hash_key->key[0]);
 	}
 
+	rss->hash_init_val = init_val;
 	old_func = rss->hash_func;
 	rss->hash_func = func;
 	rc = ena_com_set_hash_function(ena_dev);
@@ -2495,8 +2405,7 @@
 	struct ena_admin_set_feat_resp resp;
 	int ret;
 
-	if (!ena_com_check_supported_feature_id(ena_dev,
-						ENA_ADMIN_RSS_HASH_INPUT)) {
+	if (!ena_com_check_supported_feature_id(ena_dev, ENA_ADMIN_RSS_HASH_INPUT)) {
 		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n",
 			   ENA_ADMIN_RSS_HASH_INPUT);
 		return -EOPNOTSUPP;
@@ -2527,8 +2436,7 @@
 					    (struct ena_admin_acq_entry *)&resp,
 					    sizeof(resp));
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to set hash input. error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to set hash input. error: %d\n", ret);
 
 	return ret;
 }
@@ -2605,8 +2513,7 @@
 	int rc;
 
 	if (proto >= ENA_ADMIN_RSS_PROTO_NUM) {
-		netdev_err(ena_dev->net_device, "Invalid proto num (%u)\n",
-			   proto);
+		netdev_err(ena_dev->net_device, "Invalid proto num (%u)\n", proto);
 		return -EINVAL;
 	}
 
@@ -2658,8 +2565,7 @@
 	struct ena_admin_set_feat_resp resp;
 	int ret;
 
-	if (!ena_com_check_supported_feature_id(
-		    ena_dev, ENA_ADMIN_RSS_INDIRECTION_TABLE_CONFIG)) {
+	if (!ena_com_check_supported_feature_id(ena_dev, ENA_ADMIN_RSS_INDIRECTION_TABLE_CONFIG)) {
 		netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n",
 			   ENA_ADMIN_RSS_INDIRECTION_TABLE_CONFIG);
 		return -EOPNOTSUPP;
@@ -2699,8 +2605,7 @@
 					    sizeof(resp));
 
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to set indirect table. error: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to set indirect table. error: %d\n", ret);
 
 	return ret;
 }
@@ -2779,9 +2684,8 @@
 {
 	struct ena_host_attribute *host_attr = &ena_dev->host_attr;
 
-	host_attr->host_info =
-		dma_alloc_coherent(ena_dev->dmadev, SZ_4K,
-				   &host_attr->host_info_dma_addr, GFP_KERNEL);
+	host_attr->host_info = dma_alloc_coherent(ena_dev->dmadev, SZ_4K,
+						  &host_attr->host_info_dma_addr, GFP_KERNEL);
 	if (unlikely(!host_attr->host_info))
 		return -ENOMEM;
 
@@ -2827,8 +2731,7 @@
 
 	if (host_attr->debug_area_virt_addr) {
 		dma_free_coherent(ena_dev->dmadev, host_attr->debug_area_size,
-				  host_attr->debug_area_virt_addr,
-				  host_attr->debug_area_dma_addr);
+				  host_attr->debug_area_virt_addr, host_attr->debug_area_dma_addr);
 		host_attr->debug_area_virt_addr = NULL;
 	}
 }
@@ -2877,8 +2780,7 @@
 					    sizeof(resp));
 
 	if (unlikely(ret))
-		netdev_err(ena_dev->net_device,
-			   "Failed to set host attributes: %d\n", ret);
+		netdev_err(ena_dev->net_device, "Failed to set host attributes: %d\n", ret);
 
 	return ret;
 }
@@ -2896,8 +2798,7 @@
 							  u32 *intr_moder_interval)
 {
 	if (!intr_delay_resolution) {
-		netdev_err(ena_dev->net_device,
-			   "Illegal interrupt delay granularity value\n");
+		netdev_err(ena_dev->net_device, "Illegal interrupt delay granularity value\n");
 		return -EFAULT;
 	}
 
@@ -2935,14 +2836,12 @@
 
 	if (rc) {
 		if (rc == -EOPNOTSUPP) {
-			netdev_dbg(ena_dev->net_device,
-				   "Feature %d isn't supported\n",
+			netdev_dbg(ena_dev->net_device, "Feature %d isn't supported\n",
 				   ENA_ADMIN_INTERRUPT_MODERATION);
 			rc = 0;
 		} else {
 			netdev_err(ena_dev->net_device,
-				   "Failed to get interrupt moderation admin cmd. rc: %d\n",
-				   rc);
+				   "Failed to get interrupt moderation admin cmd. rc: %d\n", rc);
 		}
 
 		/* no moderation supported, disable adaptive support */
@@ -2990,8 +2889,7 @@
 		(llq_info->descs_num_before_header * sizeof(struct ena_eth_io_tx_desc));
 
 	if (unlikely(ena_dev->tx_max_header_size == 0)) {
-		netdev_err(ena_dev->net_device,
-			   "The size of the LLQ entry is smaller than needed\n");
+		netdev_err(ena_dev->net_device, "The size of the LLQ entry is smaller than needed\n");
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_com.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_com.h
@@ -46,7 +46,7 @@
 /*****************************************************************************/
 /* ENA adaptive interrupt moderation settings */
 
-#define ENA_INTR_INITIAL_TX_INTERVAL_USECS 64
+#define ENA_INTR_INITIAL_TX_INTERVAL_USECS 0
 #define ENA_INTR_INITIAL_RX_INTERVAL_USECS 0
 #define ENA_DEFAULT_INTR_DELAY_RESOLUTION 1
 
@@ -314,6 +314,7 @@
 
 	struct ena_rss rss;
 	u32 supported_features;
+	u32 capabilities;
 	u32 dma_addr_bits;
 
 	struct ena_host_attribute host_attr;
@@ -967,6 +968,18 @@
 	ena_dev->adaptive_coalescing = false;
 }
 
+/* ena_com_get_cap - query whether device supports a capability.
+ * @ena_dev: ENA communication layer struct
+ * @cap_id: enum value representing the capability
+ *
+ * @return - true if capability is supported or false otherwise
+ */
+static inline bool ena_com_get_cap(struct ena_com_dev *ena_dev,
+				   enum ena_admin_aq_caps_id cap_id)
+{
+	return !!(ena_dev->capabilities & BIT(cap_id));
+}
+
 /* ena_com_update_intr_reg - Prepare interrupt register
  * @intr_reg: interrupt register to update.
  * @rx_delay_interval: Rx interval in usecs
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_eth_com.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_eth_com.c
@@ -18,8 +18,7 @@
 	cdesc = (struct ena_eth_io_rx_cdesc_base *)(io_cq->cdesc_addr.virt_addr
 			+ (head_masked * io_cq->cdesc_entry_size_in_bytes));
 
-	desc_phase = (READ_ONCE(cdesc->status) &
-		      ENA_ETH_IO_RX_CDESC_BASE_PHASE_MASK) >>
+	desc_phase = (READ_ONCE(cdesc->status) & ENA_ETH_IO_RX_CDESC_BASE_PHASE_MASK) >>
 		     ENA_ETH_IO_RX_CDESC_BASE_PHASE_SHIFT;
 
 	if (desc_phase != expected_phase)
@@ -65,8 +64,8 @@
 
 		io_sq->entries_in_tx_burst_left--;
 		netdev_dbg(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-			   "Decreasing entries_in_tx_burst_left of queue %d to %d\n",
-			   io_sq->qid, io_sq->entries_in_tx_burst_left);
+			   "Decreasing entries_in_tx_burst_left of queue %d to %d\n", io_sq->qid,
+			   io_sq->entries_in_tx_burst_left);
 	}
 
 	/* Make sure everything was written into the bounce buffer before
@@ -75,8 +74,8 @@
 	wmb();
 
 	/* The line is completed. Copy it to dev */
-	__iowrite64_copy(io_sq->desc_addr.pbuf_dev_addr + dst_offset,
-			 bounce_buffer, (llq_info->desc_list_entry_size) / 8);
+	__iowrite64_copy(io_sq->desc_addr.pbuf_dev_addr + dst_offset, bounce_buffer,
+			 (llq_info->desc_list_entry_size) / 8);
 
 	io_sq->tail++;
 
@@ -102,16 +101,14 @@
 	header_offset =
 		llq_info->descs_num_before_header * io_sq->desc_entry_size;
 
-	if (unlikely((header_offset + header_len) >
-		     llq_info->desc_list_entry_size)) {
+	if (unlikely((header_offset + header_len) > llq_info->desc_list_entry_size)) {
 		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
 			   "Trying to write header larger than llq entry can accommodate\n");
 		return -EFAULT;
 	}
 
 	if (unlikely(!bounce_buffer)) {
-		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-			   "Bounce buffer is NULL\n");
+		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device, "Bounce buffer is NULL\n");
 		return -EFAULT;
 	}
 
@@ -129,8 +126,7 @@
 	bounce_buffer = pkt_ctrl->curr_bounce_buf;
 
 	if (unlikely(!bounce_buffer)) {
-		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-			   "Bounce buffer is NULL\n");
+		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device, "Bounce buffer is NULL\n");
 		return NULL;
 	}
 
@@ -247,8 +243,7 @@
 
 		ena_com_cq_inc_head(io_cq);
 		count++;
-		last = (READ_ONCE(cdesc->status) &
-			ENA_ETH_IO_RX_CDESC_BASE_LAST_MASK) >>
+		last = (READ_ONCE(cdesc->status) & ENA_ETH_IO_RX_CDESC_BASE_LAST_MASK) >>
 		       ENA_ETH_IO_RX_CDESC_BASE_LAST_SHIFT;
 	} while (!last);
 
@@ -328,9 +323,6 @@
 	 * compare it to the stored version, just create the meta
 	 */
 	if (io_sq->disable_meta_caching) {
-		if (unlikely(!ena_tx_ctx->meta_valid))
-			return -EINVAL;
-
 		*have_meta = true;
 		return ena_com_create_meta(io_sq, ena_meta);
 	}
@@ -372,9 +364,8 @@
 
 	netdev_dbg(ena_com_io_cq_to_ena_dev(io_cq)->net_device,
 		   "l3_proto %d l4_proto %d l3_csum_err %d l4_csum_err %d hash %d frag %d cdesc_status %x\n",
-		   ena_rx_ctx->l3_proto, ena_rx_ctx->l4_proto,
-		   ena_rx_ctx->l3_csum_err, ena_rx_ctx->l4_csum_err,
-		   ena_rx_ctx->hash, ena_rx_ctx->frag, cdesc->status);
+		   ena_rx_ctx->l3_proto, ena_rx_ctx->l4_proto, ena_rx_ctx->l3_csum_err,
+		   ena_rx_ctx->l4_csum_err, ena_rx_ctx->hash, ena_rx_ctx->frag, cdesc->status);
 }
 
 /*****************************************************************************/
@@ -406,13 +397,12 @@
 
 	if (unlikely(header_len > io_sq->tx_max_header_size)) {
 		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-			   "Header size is too large %d max header: %d\n",
-			   header_len, io_sq->tx_max_header_size);
+			   "Header size is too large %d max header: %d\n", header_len,
+			   io_sq->tx_max_header_size);
 		return -EINVAL;
 	}
 
-	if (unlikely(io_sq->mem_queue_type == ENA_ADMIN_PLACEMENT_POLICY_DEV &&
-		     !buffer_to_push)) {
+	if (unlikely(io_sq->mem_queue_type == ENA_ADMIN_PLACEMENT_POLICY_DEV && !buffer_to_push)) {
 		netdev_err(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
 			   "Push header wasn't provided in LLQ mode\n");
 		return -EINVAL;
@@ -559,13 +549,11 @@
 	}
 
 	netdev_dbg(ena_com_io_cq_to_ena_dev(io_cq)->net_device,
-		   "Fetch rx packet: queue %d completed desc: %d\n", io_cq->qid,
-		   nb_hw_desc);
+		   "Fetch rx packet: queue %d completed desc: %d\n", io_cq->qid, nb_hw_desc);
 
 	if (unlikely(nb_hw_desc > ena_rx_ctx->max_bufs)) {
 		netdev_err(ena_com_io_cq_to_ena_dev(io_cq)->net_device,
-			   "Too many RX cdescs (%d) > MAX(%d)\n", nb_hw_desc,
-			   ena_rx_ctx->max_bufs);
+			   "Too many RX cdescs (%d) > MAX(%d)\n", nb_hw_desc, ena_rx_ctx->max_bufs);
 		return -ENOSPC;
 	}
 
@@ -589,8 +577,8 @@
 	io_sq->next_to_comp += nb_hw_desc;
 
 	netdev_dbg(ena_com_io_cq_to_ena_dev(io_cq)->net_device,
-		   "[%s][QID#%d] Updating SQ head to: %d\n", __func__,
-		   io_sq->qid, io_sq->next_to_comp);
+		   "[%s][QID#%d] Updating SQ head to: %d\n", __func__, io_sq->qid,
+		   io_sq->next_to_comp);
 
 	/* Get rx flags from the last pkt */
 	ena_com_rx_set_flags(io_cq, ena_rx_ctx, cdesc);
@@ -627,8 +615,8 @@
 	desc->req_id = req_id;
 
 	netdev_dbg(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-		   "[%s] Adding single RX desc, Queue: %u, req_id: %u\n",
-		   __func__, io_sq->qid, req_id);
+		   "[%s] Adding single RX desc, Queue: %u, req_id: %u\n", __func__, io_sq->qid,
+		   req_id);
 
 	desc->buff_addr_lo = (u32)ena_buf->paddr;
 	desc->buff_addr_hi =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_eth_com.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_eth_com.h
@@ -141,8 +141,8 @@
 	}
 
 	netdev_dbg(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-		   "Queue: %d num_descs: %d num_entries_needed: %d\n",
-		   io_sq->qid, num_descs, num_entries_needed);
+		   "Queue: %d num_descs: %d num_entries_needed: %d\n", io_sq->qid, num_descs,
+		   num_entries_needed);
 
 	return num_entries_needed > io_sq->entries_in_tx_burst_left;
 }
@@ -153,15 +153,14 @@
 	u16 tail = io_sq->tail;
 
 	netdev_dbg(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-		   "Write submission queue doorbell for queue: %d tail: %d\n",
-		   io_sq->qid, tail);
+		   "Write submission queue doorbell for queue: %d tail: %d\n", io_sq->qid, tail);
 
 	writel(tail, io_sq->db_addr);
 
 	if (is_llq_max_tx_burst_exists(io_sq)) {
 		netdev_dbg(ena_com_io_sq_to_ena_dev(io_sq)->net_device,
-			   "Reset available entries in tx burst for queue %d to %d\n",
-			   io_sq->qid, max_entries_in_tx_burst);
+			   "Reset available entries in tx burst for queue %d to %d\n", io_sq->qid,
+			   max_entries_in_tx_burst);
 		io_sq->entries_in_tx_burst_left = max_entries_in_tx_burst;
 	}
 
@@ -244,8 +243,8 @@
 
 	*req_id = READ_ONCE(cdesc->req_id);
 	if (unlikely(*req_id >= io_cq->q_depth)) {
-		netdev_err(ena_com_io_cq_to_ena_dev(io_cq)->net_device,
-			   "Invalid req id %d\n", cdesc->req_id);
+		netdev_err(ena_com_io_cq_to_ena_dev(io_cq)->net_device, "Invalid req id %d\n",
+			   cdesc->req_id);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_ethtool.c
@@ -880,11 +880,7 @@
 	switch (tuna->id) {
 	case ETHTOOL_RX_COPYBREAK:
 		len = *(u32 *)data;
-		if (len > adapter->netdev->mtu) {
-			ret = -EINVAL;
-			break;
-		}
-		adapter->rx_copybreak = len;
+		ret = ena_set_rx_copybreak(adapter, len);
 		break;
 	default:
 		ret = -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_netdev.c
@@ -31,8 +31,6 @@
 
 #define ENA_MAX_RINGS min_t(unsigned int, ENA_MAX_NUM_IO_QUEUES, num_possible_cpus())
 
-#define ENA_NAPI_BUDGET 64
-
 #define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_IFUP | \
 		NETIF_MSG_TX_DONE | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR)
 
@@ -76,6 +74,8 @@
 			      struct ena_tx_buffer *tx_info);
 static int ena_create_io_tx_queues_in_range(struct ena_adapter *adapter,
 					    int first_index, int count);
+static void ena_free_all_io_tx_resources_in_range(struct ena_adapter *adapter,
+						  int first_index, int count);
 
 /* Increase a stat by cnt while holding syncp seqlock on 32bit machines */
 static void ena_increase_stat(u64 *statp, u64 cnt,
@@ -103,7 +103,7 @@
 	if (test_and_set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags))
 		return;
 
-	adapter->reset_reason = ENA_REGS_RESET_OS_NETDEV_WD;
+	ena_reset_device(adapter, ENA_REGS_RESET_OS_NETDEV_WD);
 	ena_increase_stat(&adapter->dev_stats.tx_timeout, 1, &adapter->syncp);
 
 	netif_err(adapter, tx_err, dev, "Transmit time out\n");
@@ -164,13 +164,9 @@
 	if (unlikely(rc)) {
 		netif_err(adapter, tx_queued, dev,
 			  "Failed to prepare tx bufs\n");
-		ena_increase_stat(&ring->tx_stats.prepare_ctx_err, 1,
-				  &ring->syncp);
-		if (rc != -ENOMEM) {
-			adapter->reset_reason =
-				ENA_REGS_RESET_DRIVER_INVALID_STATE;
-			set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
-		}
+		ena_increase_stat(&ring->tx_stats.prepare_ctx_err, 1, &ring->syncp);
+		if (rc != -ENOMEM)
+			ena_reset_device(adapter, ENA_REGS_RESET_DRIVER_INVALID_STATE);
 		return rc;
 	}
 
@@ -378,9 +374,9 @@
 
 static int ena_xdp_execute(struct ena_ring *rx_ring, struct xdp_buff *xdp)
 {
+	u32 verdict = ENA_XDP_PASS;
 	struct bpf_prog *xdp_prog;
 	struct ena_ring *xdp_ring;
-	u32 verdict = XDP_PASS;
 	struct xdp_frame *xdpf;
 	u64 *xdp_stat;
 
@@ -397,7 +393,7 @@
 		if (unlikely(!xdpf)) {
 			trace_xdp_exception(rx_ring->netdev, xdp_prog, verdict);
 			xdp_stat = &rx_ring->rx_stats.xdp_aborted;
-			verdict = XDP_ABORTED;
+			verdict = ENA_XDP_DROP;
 			break;
 		}
 
@@ -413,29 +409,35 @@
 
 		spin_unlock(&xdp_ring->xdp_tx_lock);
 		xdp_stat = &rx_ring->rx_stats.xdp_tx;
+		verdict = ENA_XDP_TX;
 		break;
 	case XDP_REDIRECT:
 		if (likely(!xdp_do_redirect(rx_ring->netdev, xdp, xdp_prog))) {
 			xdp_stat = &rx_ring->rx_stats.xdp_redirect;
+			verdict = ENA_XDP_REDIRECT;
 			break;
 		}
 		trace_xdp_exception(rx_ring->netdev, xdp_prog, verdict);
 		xdp_stat = &rx_ring->rx_stats.xdp_aborted;
-		verdict = XDP_ABORTED;
+		verdict = ENA_XDP_DROP;
 		break;
 	case XDP_ABORTED:
 		trace_xdp_exception(rx_ring->netdev, xdp_prog, verdict);
 		xdp_stat = &rx_ring->rx_stats.xdp_aborted;
+		verdict = ENA_XDP_DROP;
 		break;
 	case XDP_DROP:
 		xdp_stat = &rx_ring->rx_stats.xdp_drop;
+		verdict = ENA_XDP_DROP;
 		break;
 	case XDP_PASS:
 		xdp_stat = &rx_ring->rx_stats.xdp_pass;
+		verdict = ENA_XDP_PASS;
 		break;
 	default:
 		bpf_warn_invalid_xdp_action(verdict);
 		xdp_stat = &rx_ring->rx_stats.xdp_invalid;
+		verdict = ENA_XDP_DROP;
 	}
 
 	ena_increase_stat(xdp_stat, 1, &rx_ring->syncp);
@@ -455,23 +457,22 @@
 
 static int ena_setup_and_create_all_xdp_queues(struct ena_adapter *adapter)
 {
+	u32 xdp_first_ring = adapter->xdp_first_ring;
+	u32 xdp_num_queues = adapter->xdp_num_queues;
 	int rc = 0;
 
-	rc = ena_setup_tx_resources_in_range(adapter, adapter->xdp_first_ring,
-					     adapter->xdp_num_queues);
+	rc = ena_setup_tx_resources_in_range(adapter, xdp_first_ring, xdp_num_queues);
 	if (rc)
 		goto setup_err;
 
-	rc = ena_create_io_tx_queues_in_range(adapter,
-					      adapter->xdp_first_ring,
-					      adapter->xdp_num_queues);
+	rc = ena_create_io_tx_queues_in_range(adapter, xdp_first_ring, xdp_num_queues);
 	if (rc)
 		goto create_err;
 
 	return 0;
 
 create_err:
-	ena_free_all_io_tx_resources(adapter);
+	ena_free_all_io_tx_resources_in_range(adapter, xdp_first_ring, xdp_num_queues);
 setup_err:
 	return rc;
 }
@@ -516,16 +517,18 @@
 						 struct bpf_prog *prog,
 						 int first, int count)
 {
+	struct bpf_prog *old_bpf_prog;
 	struct ena_ring *rx_ring;
 	int i = 0;
 
 	for (i = first; i < count; i++) {
 		rx_ring = &adapter->rx_ring[i];
-		xchg(&rx_ring->xdp_bpf_prog, prog);
-		if (prog) {
+		old_bpf_prog = xchg(&rx_ring->xdp_bpf_prog, prog);
+
+		if (!old_bpf_prog && prog) {
 			ena_xdp_register_rxq_info(rx_ring);
 			rx_ring->rx_headroom = XDP_PACKET_HEADROOM;
-		} else {
+		} else if (old_bpf_prog && !prog) {
 			ena_xdp_unregister_rxq_info(rx_ring);
 			rx_ring->rx_headroom = NET_SKB_PAD;
 		}
@@ -676,6 +679,7 @@
 	ring->ena_dev = adapter->ena_dev;
 	ring->per_napi_packets = 0;
 	ring->cpu = 0;
+	ring->numa_node = 0;
 	ring->no_interrupt_event_cnt = 0;
 	u64_stats_init(&ring->syncp);
 }
@@ -779,6 +783,7 @@
 	tx_ring->next_to_use = 0;
 	tx_ring->next_to_clean = 0;
 	tx_ring->cpu = ena_irq->cpu;
+	tx_ring->numa_node = node;
 	return 0;
 
 err_push_buf_intermediate_buf:
@@ -911,6 +916,7 @@
 	rx_ring->next_to_clean = 0;
 	rx_ring->next_to_use = 0;
 	rx_ring->cpu = ena_irq->cpu;
+	rx_ring->numa_node = node;
 
 	return 0;
 }
@@ -984,8 +990,7 @@
 	 */
 	page = dev_alloc_page();
 	if (!page) {
-		ena_increase_stat(&rx_ring->rx_stats.page_alloc_fail, 1,
-				  &rx_ring->syncp);
+		ena_increase_stat(&rx_ring->rx_stats.page_alloc_fail, 1, &rx_ring->syncp);
 		return ERR_PTR(-ENOSPC);
 	}
 
@@ -1014,7 +1019,7 @@
 	int tailroom;
 
 	/* restore page offset value in case it has been changed by device */
-	rx_info->page_offset = headroom;
+	rx_info->buf_offset = headroom;
 
 	/* if previous allocated page is not used */
 	if (unlikely(rx_info->page))
@@ -1031,6 +1036,8 @@
 	tailroom = SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
 
 	rx_info->page = page;
+	rx_info->dma_addr = dma;
+	rx_info->page_offset = 0;
 	ena_buf = &rx_info->ena_buf;
 	ena_buf->paddr = dma + headroom;
 	ena_buf->len = ENA_PAGE_SIZE - headroom - tailroom;
@@ -1038,14 +1045,12 @@
 	return 0;
 }
 
-static void ena_unmap_rx_buff(struct ena_ring *rx_ring,
-			      struct ena_rx_buffer *rx_info)
+static void ena_unmap_rx_buff_attrs(struct ena_ring *rx_ring,
+				    struct ena_rx_buffer *rx_info,
+				    unsigned long attrs)
 {
-	struct ena_com_buf *ena_buf = &rx_info->ena_buf;
-
-	dma_unmap_page(rx_ring->dev, ena_buf->paddr - rx_ring->rx_headroom,
-		       ENA_PAGE_SIZE,
-		       DMA_BIDIRECTIONAL);
+	dma_unmap_page_attrs(rx_ring->dev, rx_info->dma_addr, ENA_PAGE_SIZE, DMA_BIDIRECTIONAL,
+			     attrs);
 }
 
 static void ena_free_rx_page(struct ena_ring *rx_ring,
@@ -1059,7 +1064,7 @@
 		return;
 	}
 
-	ena_unmap_rx_buff(rx_ring, rx_info);
+	ena_unmap_rx_buff_attrs(rx_ring, rx_info, 0);
 
 	__free_page(page);
 	rx_info->page = NULL;
@@ -1195,8 +1200,11 @@
 static void ena_free_tx_bufs(struct ena_ring *tx_ring)
 {
 	bool print_once = true;
+	bool is_xdp_ring;
 	u32 i;
 
+	is_xdp_ring = ENA_IS_XDP_INDEX(tx_ring->adapter, tx_ring->qid);
+
 	for (i = 0; i < tx_ring->ring_size; i++) {
 		struct ena_tx_buffer *tx_info = &tx_ring->tx_buffer_info[i];
 
@@ -1216,10 +1224,15 @@
 
 		ena_unmap_tx_buff(tx_ring, tx_info);
 
-		dev_kfree_skb_any(tx_info->skb);
+		if (is_xdp_ring)
+			xdp_return_frame(tx_info->xdpf);
+		else
+			dev_kfree_skb_any(tx_info->skb);
 	}
-	netdev_tx_reset_queue(netdev_get_tx_queue(tx_ring->netdev,
-						  tx_ring->qid));
+
+	if (!is_xdp_ring)
+		netdev_tx_reset_queue(netdev_get_tx_queue(tx_ring->netdev,
+							  tx_ring->qid));
 }
 
 static void ena_free_all_tx_bufs(struct ena_adapter *adapter)
@@ -1279,35 +1292,29 @@
 			  req_id);
 
 	ena_increase_stat(&ring->tx_stats.bad_req_id, 1, &ring->syncp);
+	ena_reset_device(ring->adapter, ENA_REGS_RESET_INV_TX_REQ_ID);
 
-	/* Trigger device reset */
-	ring->adapter->reset_reason = ENA_REGS_RESET_INV_TX_REQ_ID;
-	set_bit(ENA_FLAG_TRIGGER_RESET, &ring->adapter->flags);
 	return -EFAULT;
 }
 
 static int validate_tx_req_id(struct ena_ring *tx_ring, u16 req_id)
 {
-	struct ena_tx_buffer *tx_info = NULL;
+	struct ena_tx_buffer *tx_info;
 
-	if (likely(req_id < tx_ring->ring_size)) {
-		tx_info = &tx_ring->tx_buffer_info[req_id];
-		if (likely(tx_info->skb))
-			return 0;
-	}
+	tx_info = &tx_ring->tx_buffer_info[req_id];
+	if (likely(tx_info->skb))
+		return 0;
 
 	return handle_invalid_req_id(tx_ring, req_id, tx_info, false);
 }
 
 static int validate_xdp_req_id(struct ena_ring *xdp_ring, u16 req_id)
 {
-	struct ena_tx_buffer *tx_info = NULL;
+	struct ena_tx_buffer *tx_info;
 
-	if (likely(req_id < xdp_ring->ring_size)) {
-		tx_info = &xdp_ring->tx_buffer_info[req_id];
-		if (likely(tx_info->xdpf))
-			return 0;
-	}
+	tx_info = &xdp_ring->tx_buffer_info[req_id];
+	if (likely(tx_info->xdpf))
+		return 0;
 
 	return handle_invalid_req_id(xdp_ring, req_id, tx_info, true);
 }
@@ -1332,9 +1339,13 @@
 
 		rc = ena_com_tx_comp_req_id_get(tx_ring->ena_com_io_cq,
 						&req_id);
-		if (rc)
+		if (rc) {
+			if (unlikely(rc == -EINVAL))
+				handle_invalid_req_id(tx_ring, req_id, NULL, false);
 			break;
+		}
 
+		/* validate that the request id points to a valid skb */
 		rc = validate_tx_req_id(tx_ring, req_id);
 		if (rc)
 			break;
@@ -1398,15 +1409,14 @@
 	return tx_pkts;
 }
 
-static struct sk_buff *ena_alloc_skb(struct ena_ring *rx_ring, void *first_frag)
+static struct sk_buff *ena_alloc_skb(struct ena_ring *rx_ring, void *first_frag, u16 len)
 {
 	struct sk_buff *skb;
 
 	if (!first_frag)
-		skb = netdev_alloc_skb_ip_align(rx_ring->netdev,
-						rx_ring->rx_copybreak);
+		skb = napi_alloc_skb(rx_ring->napi, len);
 	else
-		skb = build_skb(first_frag, ENA_PAGE_SIZE);
+		skb = napi_build_skb(first_frag, len);
 
 	if (unlikely(!skb)) {
 		ena_increase_stat(&rx_ring->rx_stats.skb_alloc_fail, 1,
@@ -1415,23 +1425,47 @@
 		netif_dbg(rx_ring->adapter, rx_err, rx_ring->netdev,
 			  "Failed to allocate skb. first_frag %s\n",
 			  first_frag ? "provided" : "not provided");
-		return NULL;
 	}
 
 	return skb;
 }
 
+static bool ena_try_rx_buf_page_reuse(struct ena_rx_buffer *rx_info, u16 buf_len,
+				      u16 len, int pkt_offset)
+{
+	struct ena_com_buf *ena_buf = &rx_info->ena_buf;
+
+	/* More than ENA_MIN_RX_BUF_SIZE left in the reused buffer
+	 * for data + headroom + tailroom.
+	 */
+	if (SKB_DATA_ALIGN(len + pkt_offset) + ENA_MIN_RX_BUF_SIZE <= ena_buf->len) {
+		page_ref_inc(rx_info->page);
+		rx_info->page_offset += buf_len;
+		ena_buf->paddr += buf_len;
+		ena_buf->len -= buf_len;
+		return true;
+	}
+
+	return false;
+}
+
 static struct sk_buff *ena_rx_skb(struct ena_ring *rx_ring,
 				  struct ena_com_rx_buf_info *ena_bufs,
 				  u32 descs,
 				  u16 *next_to_clean)
 {
+	int tailroom = SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+	bool is_xdp_loaded = ena_xdp_present_ring(rx_ring);
 	struct ena_rx_buffer *rx_info;
+	struct ena_adapter *adapter;
+	int page_offset, pkt_offset;
+	dma_addr_t pre_reuse_paddr;
 	u16 len, req_id, buf = 0;
+	bool reuse_rx_buf_page;
 	struct sk_buff *skb;
-	void *page_addr;
-	u32 page_offset;
-	void *data_addr;
+	void *buf_addr;
+	int buf_offset;
+	u16 buf_len;
 
 	len = ena_bufs[buf].len;
 	req_id = ena_bufs[buf].req_id;
@@ -1439,8 +1473,11 @@
 	rx_info = &rx_ring->rx_buffer_info[req_id];
 
 	if (unlikely(!rx_info->page)) {
-		netif_err(rx_ring->adapter, rx_err, rx_ring->netdev,
-			  "Page is NULL\n");
+		adapter = rx_ring->adapter;
+		netif_err(adapter, rx_err, rx_ring->netdev,
+			  "Page is NULL. qid %u req_id %u\n", rx_ring->qid, req_id);
+		ena_increase_stat(&rx_ring->rx_stats.bad_req_id, 1, &rx_ring->syncp);
+		ena_reset_device(adapter, ENA_REGS_RESET_INV_RX_REQ_ID);
 		return NULL;
 	}
 
@@ -1448,34 +1485,25 @@
 		  "rx_info %p page %p\n",
 		  rx_info, rx_info->page);
 
-	/* save virt address of first buffer */
-	page_addr = page_address(rx_info->page);
+	buf_offset = rx_info->buf_offset;
+	pkt_offset = buf_offset - rx_ring->rx_headroom;
 	page_offset = rx_info->page_offset;
-	data_addr = page_addr + page_offset;
-
-	prefetch(data_addr);
+	buf_addr = page_address(rx_info->page) + page_offset;
 
 	if (len <= rx_ring->rx_copybreak) {
-		skb = ena_alloc_skb(rx_ring, NULL);
+		skb = ena_alloc_skb(rx_ring, NULL, len);
 		if (unlikely(!skb))
 			return NULL;
 
-		netif_dbg(rx_ring->adapter, rx_status, rx_ring->netdev,
-			  "RX allocated small packet. len %d. data_len %d\n",
-			  skb->len, skb->data_len);
-
-		/* sync this buffer for CPU use */
-		dma_sync_single_for_cpu(rx_ring->dev,
-					dma_unmap_addr(&rx_info->ena_buf, paddr),
-					len,
-					DMA_FROM_DEVICE);
-		skb_copy_to_linear_data(skb, data_addr, len);
+		skb_copy_to_linear_data(skb, buf_addr + buf_offset, len);
 		dma_sync_single_for_device(rx_ring->dev,
-					   dma_unmap_addr(&rx_info->ena_buf, paddr),
+					   dma_unmap_addr(&rx_info->ena_buf, paddr) + pkt_offset,
 					   len,
 					   DMA_FROM_DEVICE);
 
 		skb_put(skb, len);
+		netif_dbg(rx_ring->adapter, rx_status, rx_ring->netdev,
+			  "RX allocated small packet. len %d.\n", skb->len);
 		skb->protocol = eth_type_trans(skb, rx_ring->netdev);
 		rx_ring->free_ids[*next_to_clean] = req_id;
 		*next_to_clean = ENA_RX_RING_IDX_ADD(*next_to_clean, descs,
@@ -1483,14 +1511,21 @@
 		return skb;
 	}
 
-	ena_unmap_rx_buff(rx_ring, rx_info);
+	buf_len = SKB_DATA_ALIGN(len + buf_offset + tailroom);
+
+	/* If XDP isn't loaded try to reuse part of the RX buffer */
+	reuse_rx_buf_page = !is_xdp_loaded &&
+			    ena_try_rx_buf_page_reuse(rx_info, buf_len, len, pkt_offset);
+
+	if (!reuse_rx_buf_page)
+		ena_unmap_rx_buff_attrs(rx_ring, rx_info, DMA_ATTR_SKIP_CPU_SYNC);
 
-	skb = ena_alloc_skb(rx_ring, page_addr);
+	skb = ena_alloc_skb(rx_ring, buf_addr, buf_len);
 	if (unlikely(!skb))
 		return NULL;
 
 	/* Populate skb's linear part */
-	skb_reserve(skb, page_offset);
+	skb_reserve(skb, buf_offset);
 	skb_put(skb, len);
 	skb->protocol = eth_type_trans(skb, rx_ring->netdev);
 
@@ -1499,7 +1534,8 @@
 			  "RX skb updated. len %d. data_len %d\n",
 			  skb->len, skb->data_len);
 
-		rx_info->page = NULL;
+		if (!reuse_rx_buf_page)
+			rx_info->page = NULL;
 
 		rx_ring->free_ids[*next_to_clean] = req_id;
 		*next_to_clean =
@@ -1514,10 +1550,27 @@
 
 		rx_info = &rx_ring->rx_buffer_info[req_id];
 
-		ena_unmap_rx_buff(rx_ring, rx_info);
+		/* rx_info->buf_offset includes rx_ring->rx_headroom */
+		buf_offset = rx_info->buf_offset;
+		pkt_offset = buf_offset - rx_ring->rx_headroom;
+		buf_len = SKB_DATA_ALIGN(len + buf_offset + tailroom);
+		page_offset = rx_info->page_offset;
+
+		pre_reuse_paddr = dma_unmap_addr(&rx_info->ena_buf, paddr);
+
+		reuse_rx_buf_page = !is_xdp_loaded &&
+				    ena_try_rx_buf_page_reuse(rx_info, buf_len, len, pkt_offset);
+
+		dma_sync_single_for_cpu(rx_ring->dev,
+					pre_reuse_paddr + pkt_offset,
+					len,
+					DMA_FROM_DEVICE);
+
+		if (!reuse_rx_buf_page)
+			ena_unmap_rx_buff_attrs(rx_ring, rx_info, DMA_ATTR_SKIP_CPU_SYNC);
 
 		skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, rx_info->page,
-				rx_info->page_offset, len, ENA_PAGE_SIZE);
+				page_offset + buf_offset, len, buf_len);
 
 	} while (1);
 
@@ -1608,26 +1661,29 @@
 	}
 }
 
-static int ena_xdp_handle_buff(struct ena_ring *rx_ring, struct xdp_buff *xdp)
+static int ena_xdp_handle_buff(struct ena_ring *rx_ring, struct xdp_buff *xdp, u16 num_descs)
 {
 	struct ena_rx_buffer *rx_info;
 	int ret;
 
+	/* XDP multi-buffer packets not supported */
+	if (unlikely(num_descs > 1)) {
+		netdev_err_once(rx_ring->adapter->netdev,
+				"xdp: dropped unsupported multi-buffer packets\n");
+		ena_increase_stat(&rx_ring->rx_stats.xdp_drop, 1, &rx_ring->syncp);
+		return ENA_XDP_DROP;
+	}
+
 	rx_info = &rx_ring->rx_buffer_info[rx_ring->ena_bufs[0].req_id];
 	xdp_prepare_buff(xdp, page_address(rx_info->page),
-			 rx_info->page_offset,
+			 rx_info->buf_offset,
 			 rx_ring->ena_bufs[0].len, false);
-	/* If for some reason we received a bigger packet than
-	 * we expect, then we simply drop it
-	 */
-	if (unlikely(rx_ring->ena_bufs[0].len > ENA_XDP_MAX_MTU))
-		return XDP_DROP;
 
 	ret = ena_xdp_execute(rx_ring, xdp);
 
 	/* The xdp program might expand the headers */
-	if (ret == XDP_PASS) {
-		rx_info->page_offset = xdp->data - xdp->data_hard_start;
+	if (ret == ENA_XDP_PASS) {
+		rx_info->buf_offset = xdp->data - xdp->data_hard_start;
 		rx_ring->ena_bufs[0].len = xdp->data_end - xdp->data;
 	}
 
@@ -1656,6 +1712,7 @@
 	int xdp_flags = 0;
 	int total_len = 0;
 	int xdp_verdict;
+	u8 pkt_offset;
 	int rc = 0;
 	int i;
 
@@ -1665,7 +1722,7 @@
 	xdp_init_buff(&xdp, ENA_PAGE_SIZE, &rx_ring->xdp_rxq);
 
 	do {
-		xdp_verdict = XDP_PASS;
+		xdp_verdict = ENA_XDP_PASS;
 		skb = NULL;
 		ena_rx_ctx.ena_bufs = rx_ring->ena_bufs;
 		ena_rx_ctx.max_bufs = rx_ring->sgl_size;
@@ -1682,18 +1739,24 @@
 
 		/* First descriptor might have an offset set by the device */
 		rx_info = &rx_ring->rx_buffer_info[rx_ring->ena_bufs[0].req_id];
-		rx_info->page_offset += ena_rx_ctx.pkt_offset;
+		pkt_offset = ena_rx_ctx.pkt_offset;
+		rx_info->buf_offset += pkt_offset;
 
 		netif_dbg(rx_ring->adapter, rx_status, rx_ring->netdev,
 			  "rx_poll: q %d got packet from ena. descs #: %d l3 proto %d l4 proto %d hash: %x\n",
 			  rx_ring->qid, ena_rx_ctx.descs, ena_rx_ctx.l3_proto,
 			  ena_rx_ctx.l4_proto, ena_rx_ctx.hash);
 
+		dma_sync_single_for_cpu(rx_ring->dev,
+					dma_unmap_addr(&rx_info->ena_buf, paddr) + pkt_offset,
+					rx_ring->ena_bufs[0].len,
+					DMA_FROM_DEVICE);
+
 		if (ena_xdp_present_ring(rx_ring))
-			xdp_verdict = ena_xdp_handle_buff(rx_ring, &xdp);
+			xdp_verdict = ena_xdp_handle_buff(rx_ring, &xdp, ena_rx_ctx.descs);
 
 		/* allocate skb and fill it */
-		if (xdp_verdict == XDP_PASS)
+		if (xdp_verdict == ENA_XDP_PASS)
 			skb = ena_rx_skb(rx_ring,
 					 rx_ring->ena_bufs,
 					 ena_rx_ctx.descs,
@@ -1711,14 +1774,16 @@
 				/* Packets was passed for transmission, unmap it
 				 * from RX side.
 				 */
-				if (xdp_verdict == XDP_TX || xdp_verdict == XDP_REDIRECT) {
-					ena_unmap_rx_buff(rx_ring,
-							  &rx_ring->rx_buffer_info[req_id]);
+				if (xdp_verdict & ENA_XDP_FORWARDED) {
+					ena_unmap_rx_buff_attrs(rx_ring,
+								&rx_ring->rx_buffer_info[req_id],
+								DMA_ATTR_SKIP_CPU_SYNC);
 					rx_ring->rx_buffer_info[req_id].page = NULL;
 				}
 			}
-			if (xdp_verdict != XDP_PASS) {
+			if (xdp_verdict != ENA_XDP_PASS) {
 				xdp_flags |= xdp_verdict;
+				total_len += ena_rx_ctx.ena_bufs[0].len;
 				res_budget--;
 				continue;
 			}
@@ -1762,26 +1827,25 @@
 		ena_refill_rx_bufs(rx_ring, refill_required);
 	}
 
-	if (xdp_flags & XDP_REDIRECT)
+	if (xdp_flags & ENA_XDP_REDIRECT)
 		xdp_do_flush_map();
 
 	return work_done;
 
 error:
+	if (xdp_flags & ENA_XDP_REDIRECT)
+		xdp_do_flush();
+
 	adapter = netdev_priv(rx_ring->netdev);
 
 	if (rc == -ENOSPC) {
-		ena_increase_stat(&rx_ring->rx_stats.bad_desc_num, 1,
-				  &rx_ring->syncp);
-		adapter->reset_reason = ENA_REGS_RESET_TOO_MANY_RX_DESCS;
+		ena_increase_stat(&rx_ring->rx_stats.bad_desc_num, 1, &rx_ring->syncp);
+		ena_reset_device(adapter, ENA_REGS_RESET_TOO_MANY_RX_DESCS);
 	} else {
 		ena_increase_stat(&rx_ring->rx_stats.bad_req_id, 1,
 				  &rx_ring->syncp);
-		adapter->reset_reason = ENA_REGS_RESET_INV_RX_REQ_ID;
+		ena_reset_device(adapter, ENA_REGS_RESET_INV_RX_REQ_ID);
 	}
-
-	set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
-
 	return 0;
 }
 
@@ -1819,8 +1883,9 @@
 static void ena_unmask_interrupt(struct ena_ring *tx_ring,
 					struct ena_ring *rx_ring)
 {
+	u32 rx_interval = tx_ring->smoothed_interval;
 	struct ena_eth_io_intr_reg intr_reg;
-	u32 rx_interval = 0;
+
 	/* Rx ring can be NULL when for XDP tx queues which don't have an
 	 * accompanying rx_ring pair.
 	 */
@@ -1858,20 +1923,27 @@
 	if (likely(tx_ring->cpu == cpu))
 		goto out;
 
+	tx_ring->cpu = cpu;
+	if (rx_ring)
+		rx_ring->cpu = cpu;
+
 	numa_node = cpu_to_node(cpu);
+
+	if (likely(tx_ring->numa_node == numa_node))
+		goto out;
+
 	put_cpu();
 
 	if (numa_node != NUMA_NO_NODE) {
 		ena_com_update_numa_node(tx_ring->ena_com_io_cq, numa_node);
-		if (rx_ring)
+		tx_ring->numa_node = numa_node;
+		if (rx_ring) {
+			rx_ring->numa_node = numa_node;
 			ena_com_update_numa_node(rx_ring->ena_com_io_cq,
 						 numa_node);
+		}
 	}
 
-	tx_ring->cpu = cpu;
-	if (rx_ring)
-		rx_ring->cpu = cpu;
-
 	return;
 out:
 	put_cpu();
@@ -1896,9 +1968,14 @@
 
 		rc = ena_com_tx_comp_req_id_get(xdp_ring->ena_com_io_cq,
 						&req_id);
-		if (rc)
+		if (rc) {
+			if (unlikely(rc == -EINVAL))
+				handle_invalid_req_id(xdp_ring, req_id, NULL,
+						      true);
 			break;
+		}
 
+		/* validate that the request id points to a valid xdp_frame */
 		rc = validate_xdp_req_id(xdp_ring, req_id);
 		if (rc)
 			break;
@@ -1987,11 +2064,10 @@
 			if (ena_com_get_adaptive_moderation_enabled(rx_ring->ena_dev))
 				ena_adjust_adaptive_rx_intr_moderation(ena_napi);
 
+			ena_update_ring_numa_node(tx_ring, rx_ring);
 			ena_unmask_interrupt(tx_ring, rx_ring);
 		}
 
-		ena_update_ring_numa_node(tx_ring, rx_ring);
-
 		ret = rx_work_done;
 	} else {
 		ret = budget;
@@ -2268,7 +2344,7 @@
 		netif_napi_add(adapter->netdev,
 			       &napi->napi,
 			       ENA_IS_XDP_INDEX(adapter, i) ? ena_xdp_io_poll : ena_io_poll,
-			       ENA_NAPI_BUDGET);
+			       NAPI_POLL_WEIGHT);
 
 		if (!ENA_IS_XDP_INDEX(adapter, i)) {
 			napi->rx_ring = &adapter->rx_ring[i];
@@ -2310,8 +2386,7 @@
 	if (!ena_dev->rss.tbl_log_size) {
 		rc = ena_rss_init_default(adapter);
 		if (rc && (rc != -EOPNOTSUPP)) {
-			netif_err(adapter, ifup, adapter->netdev,
-				  "Failed to init RSS rc: %d\n", rc);
+			netif_err(adapter, ifup, adapter->netdev, "Failed to init RSS rc: %d\n", rc);
 			return rc;
 		}
 	}
@@ -2378,7 +2453,7 @@
 	ctx.mem_queue_type = ena_dev->tx_mem_queue_type;
 	ctx.msix_vector = msix_vector;
 	ctx.queue_size = tx_ring->ring_size;
-	ctx.numa_node = cpu_to_node(tx_ring->cpu);
+	ctx.numa_node = tx_ring->numa_node;
 
 	rc = ena_com_create_io_queue(ena_dev, &ctx);
 	if (rc) {
@@ -2446,7 +2521,7 @@
 	ctx.mem_queue_type = ENA_ADMIN_PLACEMENT_POLICY_HOST;
 	ctx.msix_vector = msix_vector;
 	ctx.queue_size = rx_ring->ring_size;
-	ctx.numa_node = cpu_to_node(rx_ring->cpu);
+	ctx.numa_node = rx_ring->numa_node;
 
 	rc = ena_com_create_io_queue(ena_dev, &ctx);
 	if (rc) {
@@ -2807,6 +2882,24 @@
 	return dev_was_up ? ena_up(adapter) : 0;
 }
 
+int ena_set_rx_copybreak(struct ena_adapter *adapter, u32 rx_copybreak)
+{
+	struct ena_ring *rx_ring;
+	int i;
+
+	if (rx_copybreak > min_t(u16, adapter->netdev->mtu, ENA_PAGE_SIZE))
+		return -EINVAL;
+
+	adapter->rx_copybreak = rx_copybreak;
+
+	for (i = 0; i < adapter->num_io_queues; i++) {
+		rx_ring = &adapter->rx_ring[i];
+		rx_ring->rx_copybreak = rx_copybreak;
+	}
+
+	return 0;
+}
+
 int ena_update_queue_count(struct ena_adapter *adapter, u32 new_channel_count)
 {
 	struct ena_com_dev *ena_dev = adapter->ena_dev;
@@ -3132,22 +3225,6 @@
 	return NETDEV_TX_OK;
 }
 
-static u16 ena_select_queue(struct net_device *dev, struct sk_buff *skb,
-			    struct net_device *sb_dev)
-{
-	u16 qid;
-	/* we suspect that this is good for in--kernel network services that
-	 * want to loop incoming skb rx to tx in normal user generated traffic,
-	 * most probably we will not get to this
-	 */
-	if (skb_rx_queue_recorded(skb))
-		qid = skb_get_rx_queue(skb);
-	else
-		qid = netdev_pick_tx(dev, skb, NULL);
-
-	return qid;
-}
-
 static void ena_config_host_info(struct ena_com_dev *ena_dev, struct pci_dev *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -3182,7 +3259,8 @@
 		ENA_ADMIN_HOST_INFO_RX_OFFSET_MASK |
 		ENA_ADMIN_HOST_INFO_INTERRUPT_MODERATION_MASK |
 		ENA_ADMIN_HOST_INFO_RX_BUF_MIRRORING_MASK |
-		ENA_ADMIN_HOST_INFO_RSS_CONFIGURABLE_FUNCTION_KEY_MASK;
+		ENA_ADMIN_HOST_INFO_RSS_CONFIGURABLE_FUNCTION_KEY_MASK |
+		ENA_ADMIN_HOST_INFO_RX_PAGE_REUSE_MASK;
 
 	rc = ena_com_set_host_attributes(ena_dev);
 	if (rc) {
@@ -3225,8 +3303,7 @@
 	rc = ena_com_set_host_attributes(adapter->ena_dev);
 	if (rc) {
 		if (rc == -EOPNOTSUPP)
-			netif_warn(adapter, drv, adapter->netdev,
-				   "Cannot set host attributes\n");
+			netif_warn(adapter, drv, adapter->netdev, "Cannot set host attributes\n");
 		else
 			netif_err(adapter, drv, adapter->netdev,
 				  "Cannot set host attributes\n");
@@ -3317,7 +3394,6 @@
 	.ndo_open		= ena_open,
 	.ndo_stop		= ena_close,
 	.ndo_start_xmit		= ena_start_xmit,
-	.ndo_select_queue	= ena_select_queue,
 	.ndo_get_stats64	= ena_get_stats64,
 	.ndo_tx_timeout		= ena_tx_timeout,
 	.ndo_change_mtu		= ena_change_mtu,
@@ -3694,9 +3770,8 @@
 		netif_err(adapter, rx_err, adapter->netdev,
 			  "Potential MSIX issue on Rx side Queue = %d. Reset the device\n",
 			  rx_ring->qid);
-		adapter->reset_reason = ENA_REGS_RESET_MISS_INTERRUPT;
-		smp_mb__before_atomic();
-		set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
+
+		ena_reset_device(adapter, ENA_REGS_RESET_MISS_INTERRUPT);
 		return -EIO;
 	}
 
@@ -3733,9 +3808,7 @@
 			netif_err(adapter, tx_err, adapter->netdev,
 				  "Potential MSIX issue on Tx side Queue = %d. Reset the device\n",
 				  tx_ring->qid);
-			adapter->reset_reason = ENA_REGS_RESET_MISS_INTERRUPT;
-			smp_mb__before_atomic();
-			set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
+			ena_reset_device(adapter, ENA_REGS_RESET_MISS_INTERRUPT);
 			return -EIO;
 		}
 
@@ -3761,9 +3834,7 @@
 			  "The number of lost tx completions is above the threshold (%d > %d). Reset the device\n",
 			  missed_tx,
 			  adapter->missing_tx_completion_threshold);
-		adapter->reset_reason =
-			ENA_REGS_RESET_MISS_TX_CMPL;
-		set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
+		ena_reset_device(adapter, ENA_REGS_RESET_MISS_TX_CMPL);
 		rc = -EIO;
 	}
 
@@ -3777,10 +3848,11 @@
 {
 	struct ena_ring *tx_ring;
 	struct ena_ring *rx_ring;
-	int i, budget, rc;
+	int qid, budget, rc;
 	int io_queue_count;
 
 	io_queue_count = adapter->xdp_num_queues + adapter->num_io_queues;
+
 	/* Make sure the driver doesn't turn the device in other process */
 	smp_rmb();
 
@@ -3793,27 +3865,29 @@
 	if (adapter->missing_tx_completion_to == ENA_HW_HINTS_NO_TIMEOUT)
 		return;
 
-	budget = ENA_MONITORED_TX_QUEUES;
+	budget = min_t(u32, io_queue_count, ENA_MONITORED_TX_QUEUES);
 
-	for (i = adapter->last_monitored_tx_qid; i < io_queue_count; i++) {
-		tx_ring = &adapter->tx_ring[i];
-		rx_ring = &adapter->rx_ring[i];
+	qid = adapter->last_monitored_tx_qid;
+
+	while (budget) {
+		qid = (qid + 1) % io_queue_count;
+
+		tx_ring = &adapter->tx_ring[qid];
+		rx_ring = &adapter->rx_ring[qid];
 
 		rc = check_missing_comp_in_tx_queue(adapter, tx_ring);
 		if (unlikely(rc))
 			return;
 
-		rc =  !ENA_IS_XDP_INDEX(adapter, i) ?
+		rc =  !ENA_IS_XDP_INDEX(adapter, qid) ?
 			check_for_rx_interrupt_queue(adapter, rx_ring) : 0;
 		if (unlikely(rc))
 			return;
 
 		budget--;
-		if (!budget)
-			break;
 	}
 
-	adapter->last_monitored_tx_qid = i % io_queue_count;
+	adapter->last_monitored_tx_qid = qid;
 }
 
 /* trigger napi schedule after 2 consecutive detections */
@@ -3884,8 +3958,7 @@
 			  "Keep alive watchdog timeout.\n");
 		ena_increase_stat(&adapter->dev_stats.wd_expired, 1,
 				  &adapter->syncp);
-		adapter->reset_reason = ENA_REGS_RESET_KEEP_ALIVE_TO;
-		set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
+		ena_reset_device(adapter, ENA_REGS_RESET_KEEP_ALIVE_TO);
 	}
 }
 
@@ -3896,8 +3969,7 @@
 			  "ENA admin queue is not in running state!\n");
 		ena_increase_stat(&adapter->dev_stats.admin_q_pause, 1,
 				  &adapter->syncp);
-		adapter->reset_reason = ENA_REGS_RESET_ADMIN_TO;
-		set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
+		ena_reset_device(adapter, ENA_REGS_RESET_ADMIN_TO);
 	}
 }
 
@@ -4013,10 +4085,6 @@
 	max_num_io_queues = min_t(u32, max_num_io_queues, io_tx_cq_num);
 	/* 1 IRQ for mgmnt and 1 IRQs for each IO direction */
 	max_num_io_queues = min_t(u32, max_num_io_queues, pci_msix_vec_count(pdev) - 1);
-	if (unlikely(!max_num_io_queues)) {
-		dev_err(&pdev->dev, "The device doesn't have io queues\n");
-		return -EFAULT;
-	}
 
 	return max_num_io_queues;
 }
@@ -4073,7 +4141,7 @@
 		ether_addr_copy(adapter->mac_addr, netdev->dev_addr);
 	} else {
 		ether_addr_copy(adapter->mac_addr, feat->dev_attr.mac_addr);
-		ether_addr_copy(netdev->dev_addr, adapter->mac_addr);
+		eth_hw_addr_set(netdev, adapter->mac_addr);
 	}
 
 	/* Set offload features */
@@ -4107,8 +4175,8 @@
 		}
 	}
 
-	rc = ena_com_fill_hash_function(ena_dev, ENA_ADMIN_TOEPLITZ, NULL,
-					ENA_HASH_KEY_SIZE, 0xFFFFFFFF);
+	rc = ena_com_fill_hash_function(ena_dev, ENA_ADMIN_TOEPLITZ, NULL, ENA_HASH_KEY_SIZE,
+					0xFFFFFFFF);
 	if (unlikely(rc && (rc != -EOPNOTSUPP))) {
 		dev_err(dev, "Cannot fill hash function\n");
 		goto err_fill_indir;
@@ -4574,13 +4642,19 @@
 
 static int __init ena_init(void)
 {
+	int ret;
+
 	ena_wq = create_singlethread_workqueue(DRV_MODULE_NAME);
 	if (!ena_wq) {
 		pr_err("Failed to create workqueue\n");
 		return -ENOMEM;
 	}
 
-	return pci_register_driver(&ena_pci_driver);
+	ret = pci_register_driver(&ena_pci_driver);
+	if (ret)
+		destroy_workqueue(ena_wq);
+
+	return ret;
 }
 
 static void __exit ena_cleanup(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amazon/ena/ena_netdev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amazon/ena/ena_netdev.h
@@ -50,6 +50,8 @@
 #define ENA_DEFAULT_RING_SIZE	(1024)
 #define ENA_MIN_RING_SIZE	(256)
 
+#define ENA_MIN_RX_BUF_SIZE (2048)
+
 #define ENA_MIN_NUM_IO_QUEUES	(1)
 
 #define ENA_TX_WAKEUP_THRESH		(MAX_SKB_FRAGS + 2)
@@ -186,7 +188,9 @@
 struct ena_rx_buffer {
 	struct sk_buff *skb;
 	struct page *page;
+	dma_addr_t dma_addr;
 	u32 page_offset;
+	u32 buf_offset;
 	struct ena_com_buf ena_buf;
 } ____cacheline_aligned;
 
@@ -273,9 +277,11 @@
 	bool disable_meta_caching;
 	u16 no_interrupt_event_cnt;
 
-	/* cpu for TPH */
+	/* cpu and NUMA for TPH */
 	int cpu;
-	 /* number of tx/rx_buffer_info's entries */
+	int numa_node;
+
+	/* number of tx/rx_buffer_info's entries */
 	int ring_size;
 
 	enum ena_admin_placement_policy_type tx_mem_queue_type;
@@ -404,14 +410,34 @@
 
 int ena_update_queue_count(struct ena_adapter *adapter, u32 new_channel_count);
 
+int ena_set_rx_copybreak(struct ena_adapter *adapter, u32 rx_copybreak);
+
 int ena_get_sset_count(struct net_device *netdev, int sset);
 
+static inline void ena_reset_device(struct ena_adapter *adapter,
+				    enum ena_regs_reset_reason_types reset_reason)
+{
+	adapter->reset_reason = reset_reason;
+	/* Make sure reset reason is set before triggering the reset */
+	smp_mb__before_atomic();
+	set_bit(ENA_FLAG_TRIGGER_RESET, &adapter->flags);
+}
+
 enum ena_xdp_errors_t {
 	ENA_XDP_ALLOWED = 0,
 	ENA_XDP_CURRENT_MTU_TOO_LARGE,
 	ENA_XDP_NO_ENOUGH_QUEUES,
 };
 
+enum ENA_XDP_ACTIONS {
+	ENA_XDP_PASS		= 0,
+	ENA_XDP_TX		= BIT(0),
+	ENA_XDP_REDIRECT	= BIT(1),
+	ENA_XDP_DROP		= BIT(2)
+};
+
+#define ENA_XDP_FORWARDED (ENA_XDP_TX | ENA_XDP_REDIRECT)
+
 static inline bool ena_xdp_present(struct ena_adapter *adapter)
 {
 	return !!adapter->xdp_bpf_prog;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/Kconfig
@@ -168,7 +168,7 @@
 
 config AMD_XGBE
 	tristate "AMD 10GbE Ethernet driver"
-	depends on ((OF_NET && OF_ADDRESS) || ACPI || PCI) && HAS_IOMEM
+	depends on (OF_ADDRESS || ACPI || PCI) && HAS_IOMEM
 	depends on X86 || ARM64 || COMPILE_TEST
 	depends on PTP_1588_CLOCK_OPTIONAL
 	select BITREVERSE
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/atarilance.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/atarilance.c
@@ -821,7 +821,7 @@
 	lp->memcpy_f( PKTBUF_ADDR(head), (void *)skb->data, skb->len );
 	head->flag = TMD1_OWN_CHIP | TMD1_ENP | TMD1_STP;
 	dev->stats.tx_bytes += skb->len;
-	dev_kfree_skb( skb );
+	dev_consume_skb_irq(skb);
 	lp->cur_tx++;
 	while( lp->cur_tx >= TX_RING_SIZE && lp->dirty_tx >= TX_RING_SIZE ) {
 		lp->cur_tx -= TX_RING_SIZE;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/lance.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/lance.c
@@ -999,7 +999,7 @@
 		skb_copy_from_linear_data(skb, &lp->tx_bounce_buffs[entry], skb->len);
 		lp->tx_ring[entry].base =
 			((u32)isa_virt_to_bus((lp->tx_bounce_buffs + entry)) & 0xffffff) | 0x83000000;
-		dev_kfree_skb(skb);
+		dev_consume_skb_irq(skb);
 	} else {
 		lp->tx_skbuff[entry] = skb;
 		lp->tx_ring[entry].base = ((u32)isa_virt_to_bus(skb->data) & 0xffffff) | 0x83000000;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/mvme147.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/mvme147.c
@@ -103,10 +103,6 @@
 	address = address >> 8;
 	dev->dev_addr[3] = address&0xff;
 
-	printk("%s: MVME147 at 0x%08lx, irq %d, Hardware Address %pM\n",
-	       dev->name, dev->base_addr, MVME147_LANCE_IRQ,
-	       dev->dev_addr);
-
 	lp = netdev_priv(dev);
 	lp->ram = __get_dma_pages(GFP_ATOMIC, 3);	/* 32K */
 	if (!lp->ram) {
@@ -136,6 +132,9 @@
 		return ERR_PTR(err);
 	}
 
+	netdev_info(dev, "MVME147 at 0x%08lx, irq %d, Hardware Address %pM\n",
+		    dev->base_addr, MVME147_LANCE_IRQ, dev->dev_addr);
+
 	return dev;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/nmclan_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/nmclan_cs.c
@@ -529,7 +529,8 @@
 mace_init
 	Resets the MACE chip.
 ---------------------------------------------------------------------------- */
-static int mace_init(mace_private *lp, unsigned int ioaddr, char *enet_addr)
+static int mace_init(mace_private *lp, unsigned int ioaddr,
+		     const char *enet_addr)
 {
   int i;
   int ct = 0;
@@ -650,7 +651,7 @@
     } else {
       pr_notice("mace id not found: %x %x should be 0x40 0x?9\n",
 		sig[0], sig[1]);
-      return -ENODEV;
+      goto failed;
     }
   }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-common.h
@@ -1331,6 +1331,10 @@
 #define MDIO_VEND2_PMA_CDR_CONTROL	0x8056
 #endif
 
+#ifndef MDIO_VEND2_PMA_MISC_CTRL0
+#define MDIO_VEND2_PMA_MISC_CTRL0	0x8090
+#endif
+
 #ifndef MDIO_CTRL1_SPEED1G
 #define MDIO_CTRL1_SPEED1G		(MDIO_CTRL1_SPEED10G & ~BMCR_SPEED100)
 #endif
@@ -1389,6 +1393,10 @@
 #define XGBE_PMA_RX_RST_0_RESET_ON	0x10
 #define XGBE_PMA_RX_RST_0_RESET_OFF	0x00
 
+#define XGBE_PMA_PLL_CTRL_MASK		BIT(15)
+#define XGBE_PMA_PLL_CTRL_ENABLE	BIT(15)
+#define XGBE_PMA_PLL_CTRL_DISABLE	0x0000
+
 /* Bit setting and getting macros
  *  The get macro will extract the current bit field value from within
  *  the variable
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-dev.c
@@ -524,19 +524,28 @@
 	netif_dbg(pdata, drv, pdata->netdev, "VXLAN acceleration disabled\n");
 }
 
+static unsigned int xgbe_get_fc_queue_count(struct xgbe_prv_data *pdata)
+{
+	unsigned int max_q_count = XGMAC_MAX_FLOW_CONTROL_QUEUES;
+
+	/* From MAC ver 30H the TFCR is per priority, instead of per queue */
+	if (XGMAC_GET_BITS(pdata->hw_feat.version, MAC_VR, SNPSVER) >= 0x30)
+		return max_q_count;
+	else
+		return min_t(unsigned int, pdata->tx_q_count, max_q_count);
+}
+
 static int xgbe_disable_tx_flow_control(struct xgbe_prv_data *pdata)
 {
-	unsigned int max_q_count, q_count;
 	unsigned int reg, reg_val;
-	unsigned int i;
+	unsigned int i, q_count;
 
 	/* Clear MTL flow control */
 	for (i = 0; i < pdata->rx_q_count; i++)
 		XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_Q_RQOMR, EHFC, 0);
 
 	/* Clear MAC flow control */
-	max_q_count = XGMAC_MAX_FLOW_CONTROL_QUEUES;
-	q_count = min_t(unsigned int, pdata->tx_q_count, max_q_count);
+	q_count = xgbe_get_fc_queue_count(pdata);
 	reg = MAC_Q0TFCR;
 	for (i = 0; i < q_count; i++) {
 		reg_val = XGMAC_IOREAD(pdata, reg);
@@ -553,9 +562,8 @@
 {
 	struct ieee_pfc *pfc = pdata->pfc;
 	struct ieee_ets *ets = pdata->ets;
-	unsigned int max_q_count, q_count;
 	unsigned int reg, reg_val;
-	unsigned int i;
+	unsigned int i, q_count;
 
 	/* Set MTL flow control */
 	for (i = 0; i < pdata->rx_q_count; i++) {
@@ -579,8 +587,7 @@
 	}
 
 	/* Set MAC flow control */
-	max_q_count = XGMAC_MAX_FLOW_CONTROL_QUEUES;
-	q_count = min_t(unsigned int, pdata->tx_q_count, max_q_count);
+	q_count = xgbe_get_fc_queue_count(pdata);
 	reg = MAC_Q0TFCR;
 	for (i = 0; i < q_count; i++) {
 		reg_val = XGMAC_IOREAD(pdata, reg);
@@ -1080,7 +1087,7 @@
 	return 0;
 }
 
-static int xgbe_set_mac_address(struct xgbe_prv_data *pdata, u8 *addr)
+static int xgbe_set_mac_address(struct xgbe_prv_data *pdata, const u8 *addr)
 {
 	unsigned int mac_addr_hi, mac_addr_lo;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-drv.c
@@ -682,10 +682,24 @@
 static void xgbe_service_timer(struct timer_list *t)
 {
 	struct xgbe_prv_data *pdata = from_timer(pdata, t, service_timer);
+	struct xgbe_channel *channel;
+	unsigned int i;
 
 	queue_work(pdata->dev_workqueue, &pdata->service_work);
 
 	mod_timer(&pdata->service_timer, jiffies + HZ);
+
+	if (!pdata->tx_usecs)
+		return;
+
+	for (i = 0; i < pdata->channel_count; i++) {
+		channel = pdata->channel[i];
+		if (!channel->tx_ring || channel->tx_timer_active)
+			break;
+		channel->tx_timer_active = 1;
+		mod_timer(&channel->tx_timer,
+			  jiffies + usecs_to_jiffies(pdata->tx_usecs));
+	}
 }
 
 static void xgbe_init_timers(struct xgbe_prv_data *pdata)
@@ -721,7 +735,9 @@
 		if (!channel->tx_ring)
 			break;
 
+		/* Deactivate the Tx timer */
 		del_timer_sync(&channel->tx_timer);
+		channel->tx_timer_active = 0;
 	}
 }
 
@@ -1062,6 +1078,9 @@
 
 	devm_free_irq(pdata->dev, pdata->dev_irq, pdata);
 
+	tasklet_kill(&pdata->tasklet_dev);
+	tasklet_kill(&pdata->tasklet_ecc);
+
 	if (pdata->vdata->ecc_support && (pdata->dev_irq != pdata->ecc_irq))
 		devm_free_irq(pdata->dev, pdata->ecc_irq, pdata);
 
@@ -2555,6 +2574,14 @@
 			buf2_len = xgbe_rx_buf2_len(rdata, packet, len);
 			len += buf2_len;
 
+			if (buf2_len > rdata->rx.buf.dma_len) {
+				/* Hardware inconsistency within the descriptors
+				 * that has resulted in a length underflow.
+				 */
+				error = 1;
+				goto skip_data;
+			}
+
 			if (!skb) {
 				skb = xgbe_create_skb(pdata, napi, rdata,
 						      buf1_len);
@@ -2584,8 +2611,10 @@
 		if (!last || context_next)
 			goto read_again;
 
-		if (!skb)
+		if (!skb || error) {
+			dev_kfree_skb(skb);
 			goto next_packet;
+		}
 
 		/* Be sure we don't exceed the configured MTU */
 		max_len = netdev->mtu + ETH_HLEN;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
@@ -314,10 +314,15 @@
 
 	cmd->base.phy_address = pdata->phy.address;
 
-	cmd->base.autoneg = pdata->phy.autoneg;
-	cmd->base.speed = pdata->phy.speed;
-	cmd->base.duplex = pdata->phy.duplex;
+	if (netif_carrier_ok(netdev)) {
+		cmd->base.speed = pdata->phy.speed;
+		cmd->base.duplex = pdata->phy.duplex;
+	} else {
+		cmd->base.speed = SPEED_UNKNOWN;
+		cmd->base.duplex = DUPLEX_UNKNOWN;
+	}
 
+	cmd->base.autoneg = pdata->phy.autoneg;
 	cmd->base.port = PORT_NONE;
 
 	XGBE_LM_COPY(cmd, supported, lks, supported);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-i2c.c
@@ -447,8 +447,10 @@
 	xgbe_i2c_disable(pdata);
 	xgbe_i2c_clear_all_interrupts(pdata);
 
-	if (pdata->dev_irq != pdata->i2c_irq)
+	if (pdata->dev_irq != pdata->i2c_irq) {
 		devm_free_irq(pdata->dev, pdata->i2c_irq, pdata);
+		tasklet_kill(&pdata->tasklet_i2c);
+	}
 }
 
 static int xgbe_i2c_start(struct xgbe_prv_data *pdata)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-mdio.c
@@ -496,6 +496,7 @@
 	reg |= XGBE_KR_TRAINING_ENABLE;
 	reg |= XGBE_KR_TRAINING_START;
 	XMDIO_WRITE(pdata, MDIO_MMD_PMAPMD, MDIO_PMA_10GBR_PMD_CTRL, reg);
+	pdata->kr_start_time = jiffies;
 
 	netif_dbg(pdata, link, pdata->netdev,
 		  "KR training initiated\n");
@@ -632,6 +633,8 @@
 
 	xgbe_switch_mode(pdata);
 
+	pdata->an_result = XGBE_AN_READY;
+
 	xgbe_an_restart(pdata);
 
 	return XGBE_AN_INCOMPAT_LINK;
@@ -1175,7 +1178,19 @@
 	if (pdata->phy.duplex != DUPLEX_FULL)
 		return -EINVAL;
 
-	xgbe_set_mode(pdata, mode);
+	/* Force the mode change for SFI in Fixed PHY config.
+	 * Fixed PHY configs needs PLL to be enabled while doing mode set.
+	 * When the SFP module isn't connected during boot, driver assumes
+	 * AN is ON and attempts autonegotiation. However, if the connected
+	 * SFP comes up in Fixed PHY config, the link will not come up as
+	 * PLL isn't enabled while the initial mode set command is issued.
+	 * So, force the mode change for SFI in Fixed PHY configuration to
+	 * fix link issues.
+	 */
+	if (mode == XGBE_MODE_SFI)
+		xgbe_change_mode(pdata, mode);
+	else
+		xgbe_set_mode(pdata, mode);
 
 	return 0;
 }
@@ -1275,9 +1290,30 @@
 static void xgbe_check_link_timeout(struct xgbe_prv_data *pdata)
 {
 	unsigned long link_timeout;
+	unsigned long kr_time;
+	int wait;
 
 	link_timeout = pdata->link_check + (XGBE_LINK_TIMEOUT * HZ);
 	if (time_after(jiffies, link_timeout)) {
+		if ((xgbe_cur_mode(pdata) == XGBE_MODE_KR) &&
+		    pdata->phy.autoneg == AUTONEG_ENABLE) {
+			/* AN restart should not happen while KR training is in progress.
+			 * The while loop ensures no AN restart during KR training,
+			 * waits up to 500ms and AN restart is triggered only if KR
+			 * training is failed.
+			 */
+			wait = XGBE_KR_TRAINING_WAIT_ITER;
+			while (wait--) {
+				kr_time = pdata->kr_start_time +
+					  msecs_to_jiffies(XGBE_AN_MS_TIMEOUT);
+				if (time_after(jiffies, kr_time))
+					break;
+				/* AN restart is not required, if AN result is COMPLETE */
+				if (pdata->an_result == XGBE_AN_COMPLETE)
+					return;
+				usleep_range(10000, 11000);
+			}
+		}
 		netif_dbg(pdata, link, pdata->netdev, "AN link timeout\n");
 		xgbe_phy_config_aneg(pdata);
 	}
@@ -1288,7 +1324,7 @@
 	return pdata->phy_if.phy_impl.an_outcome(pdata);
 }
 
-static void xgbe_phy_status_result(struct xgbe_prv_data *pdata)
+static bool xgbe_phy_status_result(struct xgbe_prv_data *pdata)
 {
 	struct ethtool_link_ksettings *lks = &pdata->phy.lks;
 	enum xgbe_mode mode;
@@ -1323,8 +1359,13 @@
 
 	pdata->phy.duplex = DUPLEX_FULL;
 
-	if (xgbe_set_mode(pdata, mode) && pdata->an_again)
+	if (!xgbe_set_mode(pdata, mode))
+		return false;
+
+	if (pdata->an_again)
 		xgbe_phy_reconfig_aneg(pdata);
+
+	return true;
 }
 
 static void xgbe_phy_status(struct xgbe_prv_data *pdata)
@@ -1354,7 +1395,8 @@
 			return;
 		}
 
-		xgbe_phy_status_result(pdata);
+		if (xgbe_phy_status_result(pdata))
+			return;
 
 		if (test_bit(XGBE_LINK_INIT, &pdata->dev_state))
 			clear_bit(XGBE_LINK_INIT, &pdata->dev_state);
@@ -1390,8 +1432,10 @@
 	/* Disable auto-negotiation */
 	xgbe_an_disable_all(pdata);
 
-	if (pdata->dev_irq != pdata->an_irq)
+	if (pdata->dev_irq != pdata->an_irq) {
 		devm_free_irq(pdata->dev, pdata->an_irq, pdata);
+		tasklet_kill(&pdata->tasklet_an);
+	}
 
 	pdata->phy_if.phy_impl.stop(pdata);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-pci.c
@@ -418,6 +418,9 @@
 
 	pci_free_irq_vectors(pdata->pcidev);
 
+	/* Disable all interrupts in the hardware */
+	XP_IOWRITE(pdata, XP_INT_EN, 0x0);
+
 	xgbe_free_pdata(pdata);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
@@ -189,6 +189,7 @@
 	XGBE_SFP_CABLE_UNKNOWN = 0,
 	XGBE_SFP_CABLE_ACTIVE,
 	XGBE_SFP_CABLE_PASSIVE,
+	XGBE_SFP_CABLE_FIBER,
 };
 
 enum xgbe_sfp_base {
@@ -236,9 +237,7 @@
 
 #define XGBE_SFP_BASE_BR			12
 #define XGBE_SFP_BASE_BR_1GBE_MIN		0x0a
-#define XGBE_SFP_BASE_BR_1GBE_MAX		0x0d
 #define XGBE_SFP_BASE_BR_10GBE_MIN		0x64
-#define XGBE_SFP_BASE_BR_10GBE_MAX		0x68
 
 #define XGBE_SFP_BASE_CU_CABLE_LEN		18
 
@@ -284,6 +283,8 @@
 #define XGBE_BEL_FUSE_VENDOR	"BEL-FUSE        "
 #define XGBE_BEL_FUSE_PARTNO	"1GBT-SFP06      "
 
+#define XGBE_MOLEX_VENDOR	"Molex Inc.      "
+
 struct xgbe_sfp_ascii {
 	union {
 		char vendor[XGBE_SFP_BASE_VENDOR_NAME_LEN + 1];
@@ -823,25 +824,22 @@
 static bool xgbe_phy_sfp_bit_rate(struct xgbe_sfp_eeprom *sfp_eeprom,
 				  enum xgbe_sfp_speed sfp_speed)
 {
-	u8 *sfp_base, min, max;
+	u8 *sfp_base, min;
 
 	sfp_base = sfp_eeprom->base;
 
 	switch (sfp_speed) {
 	case XGBE_SFP_SPEED_1000:
 		min = XGBE_SFP_BASE_BR_1GBE_MIN;
-		max = XGBE_SFP_BASE_BR_1GBE_MAX;
 		break;
 	case XGBE_SFP_SPEED_10000:
 		min = XGBE_SFP_BASE_BR_10GBE_MIN;
-		max = XGBE_SFP_BASE_BR_10GBE_MAX;
 		break;
 	default:
 		return false;
 	}
 
-	return ((sfp_base[XGBE_SFP_BASE_BR] >= min) &&
-		(sfp_base[XGBE_SFP_BASE_BR] <= max));
+	return sfp_base[XGBE_SFP_BASE_BR] >= min;
 }
 
 static void xgbe_phy_free_phy_device(struct xgbe_prv_data *pdata)
@@ -858,7 +856,6 @@
 
 static bool xgbe_phy_finisar_phy_quirks(struct xgbe_prv_data *pdata)
 {
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, };
 	struct xgbe_phy_data *phy_data = pdata->phy_data;
 	unsigned int phy_id = phy_data->phydev->phy_id;
 
@@ -880,14 +877,7 @@
 	phy_write(phy_data->phydev, 0x04, 0x0d01);
 	phy_write(phy_data->phydev, 0x00, 0x9140);
 
-	linkmode_set_bit_array(phy_10_100_features_array,
-			       ARRAY_SIZE(phy_10_100_features_array),
-			       supported);
-	linkmode_set_bit_array(phy_gbit_features_array,
-			       ARRAY_SIZE(phy_gbit_features_array),
-			       supported);
-
-	linkmode_copy(phy_data->phydev->supported, supported);
+	linkmode_copy(phy_data->phydev->supported, PHY_GBIT_FEATURES);
 
 	phy_support_asym_pause(phy_data->phydev);
 
@@ -899,7 +889,6 @@
 
 static bool xgbe_phy_belfuse_phy_quirks(struct xgbe_prv_data *pdata)
 {
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, };
 	struct xgbe_phy_data *phy_data = pdata->phy_data;
 	struct xgbe_sfp_eeprom *sfp_eeprom = &phy_data->sfp_eeprom;
 	unsigned int phy_id = phy_data->phydev->phy_id;
@@ -963,13 +952,7 @@
 	reg = phy_read(phy_data->phydev, 0x00);
 	phy_write(phy_data->phydev, 0x00, reg & ~0x00800);
 
-	linkmode_set_bit_array(phy_10_100_features_array,
-			       ARRAY_SIZE(phy_10_100_features_array),
-			       supported);
-	linkmode_set_bit_array(phy_gbit_features_array,
-			       ARRAY_SIZE(phy_gbit_features_array),
-			       supported);
-	linkmode_copy(phy_data->phydev->supported, supported);
+	linkmode_copy(phy_data->phydev->supported, PHY_GBIT_FEATURES);
 	phy_support_asym_pause(phy_data->phydev);
 
 	netif_dbg(pdata, drv, pdata->netdev,
@@ -1142,16 +1125,21 @@
 	phy_data->sfp_tx_fault = xgbe_phy_check_sfp_tx_fault(phy_data);
 	phy_data->sfp_rx_los = xgbe_phy_check_sfp_rx_los(phy_data);
 
-	/* Assume ACTIVE cable unless told it is PASSIVE */
+	/* Assume FIBER cable unless told otherwise */
 	if (sfp_base[XGBE_SFP_BASE_CABLE] & XGBE_SFP_BASE_CABLE_PASSIVE) {
 		phy_data->sfp_cable = XGBE_SFP_CABLE_PASSIVE;
 		phy_data->sfp_cable_len = sfp_base[XGBE_SFP_BASE_CU_CABLE_LEN];
-	} else {
+	} else if (sfp_base[XGBE_SFP_BASE_CABLE] & XGBE_SFP_BASE_CABLE_ACTIVE) {
 		phy_data->sfp_cable = XGBE_SFP_CABLE_ACTIVE;
+	} else {
+		phy_data->sfp_cable = XGBE_SFP_CABLE_FIBER;
 	}
 
 	/* Determine the type of SFP */
-	if (sfp_base[XGBE_SFP_BASE_10GBE_CC] & XGBE_SFP_BASE_10GBE_CC_SR)
+	if (phy_data->sfp_cable != XGBE_SFP_CABLE_FIBER &&
+	    xgbe_phy_sfp_bit_rate(sfp_eeprom, XGBE_SFP_SPEED_10000))
+		phy_data->sfp_base = XGBE_SFP_BASE_10000_CR;
+	else if (sfp_base[XGBE_SFP_BASE_10GBE_CC] & XGBE_SFP_BASE_10GBE_CC_SR)
 		phy_data->sfp_base = XGBE_SFP_BASE_10000_SR;
 	else if (sfp_base[XGBE_SFP_BASE_10GBE_CC] & XGBE_SFP_BASE_10GBE_CC_LR)
 		phy_data->sfp_base = XGBE_SFP_BASE_10000_LR;
@@ -1167,9 +1155,6 @@
 		phy_data->sfp_base = XGBE_SFP_BASE_1000_CX;
 	else if (sfp_base[XGBE_SFP_BASE_1GBE_CC] & XGBE_SFP_BASE_1GBE_CC_T)
 		phy_data->sfp_base = XGBE_SFP_BASE_1000_T;
-	else if ((phy_data->sfp_cable == XGBE_SFP_CABLE_PASSIVE) &&
-		 xgbe_phy_sfp_bit_rate(sfp_eeprom, XGBE_SFP_SPEED_10000))
-		phy_data->sfp_base = XGBE_SFP_BASE_10000_CR;
 
 	switch (phy_data->sfp_base) {
 	case XGBE_SFP_BASE_1000_T:
@@ -1977,12 +1962,26 @@
 	}
 }
 
+static void xgbe_phy_pll_ctrl(struct xgbe_prv_data *pdata, bool enable)
+{
+	XMDIO_WRITE_BITS(pdata, MDIO_MMD_PMAPMD, MDIO_VEND2_PMA_MISC_CTRL0,
+			 XGBE_PMA_PLL_CTRL_MASK,
+			 enable ? XGBE_PMA_PLL_CTRL_ENABLE
+				: XGBE_PMA_PLL_CTRL_DISABLE);
+
+	/* Wait for command to complete */
+	usleep_range(100, 200);
+}
+
 static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
 					unsigned int cmd, unsigned int sub_cmd)
 {
 	unsigned int s0 = 0;
 	unsigned int wait;
 
+	/* Disable PLL re-initialization during FW command processing */
+	xgbe_phy_pll_ctrl(pdata, false);
+
 	/* Log if a previous command did not complete */
 	if (XP_IOREAD_BITS(pdata, XP_DRIVER_INT_RO, STATUS)) {
 		netif_dbg(pdata, link, pdata->netdev,
@@ -2003,7 +2002,7 @@
 	wait = XGBE_RATECHANGE_COUNT;
 	while (wait--) {
 		if (!XP_IOREAD_BITS(pdata, XP_DRIVER_INT_RO, STATUS))
-			return;
+			goto reenable_pll;
 
 		usleep_range(1000, 2000);
 	}
@@ -2013,6 +2012,10 @@
 
 	/* Reset on error */
 	xgbe_phy_rx_reset(pdata);
+
+reenable_pll:
+	/* Enable PLL re-initialization */
+	xgbe_phy_pll_ctrl(pdata, true);
 }
 
 static void xgbe_phy_rrc(struct xgbe_prv_data *pdata)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/amd/xgbe/xgbe.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/amd/xgbe/xgbe.h
@@ -289,6 +289,7 @@
 /* Auto-negotiation */
 #define XGBE_AN_MS_TIMEOUT		500
 #define XGBE_LINK_TIMEOUT		5
+#define XGBE_KR_TRAINING_WAIT_ITER	50
 
 #define XGBE_SGMII_AN_LINK_STATUS	BIT(1)
 #define XGBE_SGMII_AN_LINK_SPEED	(BIT(2) | BIT(3))
@@ -729,7 +730,7 @@
 struct xgbe_hw_if {
 	int (*tx_complete)(struct xgbe_ring_desc *);
 
-	int (*set_mac_address)(struct xgbe_prv_data *, u8 *addr);
+	int (*set_mac_address)(struct xgbe_prv_data *, const u8 *addr);
 	int (*config_rx_mode)(struct xgbe_prv_data *);
 
 	int (*enable_rx_csum)(struct xgbe_prv_data *);
@@ -1253,6 +1254,7 @@
 	unsigned int parallel_detect;
 	unsigned int fec_ability;
 	unsigned long an_start;
+	unsigned long kr_start_time;
 	enum xgbe_an_mode an_mode;
 
 	/* I2C support */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apm/xgene-v2/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apm/xgene-v2/mac.c
@@ -65,7 +65,7 @@
 
 void xge_mac_set_station_addr(struct xge_pdata *pdata)
 {
-	u8 *dev_addr = pdata->ndev->dev_addr;
+	const u8 *dev_addr = pdata->ndev->dev_addr;
 	u32 addr0, addr1;
 
 	addr0 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
@@ -378,8 +378,8 @@
 
 static void xgene_gmac_set_mac_addr(struct xgene_enet_pdata *pdata)
 {
+	const u8 *dev_addr = pdata->ndev->dev_addr;
 	u32 addr0, addr1;
-	u8 *dev_addr = pdata->ndev->dev_addr;
 
 	addr0 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
 		(dev_addr[1] << 8) | dev_addr[0];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
@@ -696,6 +696,12 @@
 	buf_pool->rx_skb[skb_index] = NULL;
 
 	datalen = xgene_enet_get_data_len(le64_to_cpu(raw_desc->m1));
+
+	/* strip off CRC as HW isn't doing this */
+	nv = GET_VAL(NV, le64_to_cpu(raw_desc->m0));
+	if (!nv)
+		datalen -= 4;
+
 	skb_put(skb, datalen);
 	prefetch(skb->data - NET_IP_ALIGN);
 	skb->protocol = eth_type_trans(skb, ndev);
@@ -717,12 +723,8 @@
 		}
 	}
 
-	nv = GET_VAL(NV, le64_to_cpu(raw_desc->m0));
-	if (!nv) {
-		/* strip off CRC as HW isn't doing this */
-		datalen -= 4;
+	if (!nv)
 		goto skip_jumbo;
-	}
 
 	slots = page_pool->slots - 1;
 	head = page_pool->head;
@@ -1002,8 +1004,10 @@
 
 	xgene_enet_napi_enable(pdata);
 	ret = xgene_enet_register_irq(ndev);
-	if (ret)
+	if (ret) {
+		xgene_enet_napi_disable(pdata);
 		return ret;
+	}
 
 	if (ndev->phydev) {
 		phy_start(ndev->phydev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c
@@ -165,8 +165,8 @@
 
 static void xgene_sgmac_set_mac_addr(struct xgene_enet_pdata *p)
 {
+	const u8 *dev_addr = p->ndev->dev_addr;
 	u32 addr0, addr1;
-	u8 *dev_addr = p->ndev->dev_addr;
 
 	addr0 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
 		(dev_addr[1] << 8) | dev_addr[0];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c
@@ -207,8 +207,8 @@
 
 static void xgene_xgmac_set_mac_addr(struct xgene_enet_pdata *pdata)
 {
+	const u8 *dev_addr = pdata->ndev->dev_addr;
 	u32 addr0, addr1;
-	u8 *dev_addr = pdata->ndev->dev_addr;
 
 	addr0 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
 		(dev_addr[1] << 8) | dev_addr[0];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apple/bmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apple/bmac.c
@@ -308,7 +308,7 @@
 {
 	struct bmac_data *bp = netdev_priv(dev);
 	volatile unsigned short regValue;
-	unsigned short *pWord16;
+	const unsigned short *pWord16;
 	int i;
 
 	/* XXDEBUG(("bmac: enter init_registers\n")); */
@@ -371,7 +371,7 @@
 	bmwrite(dev, BHASH1, bp->hash_table_mask[2]); 	/* bits 47 - 32 */
 	bmwrite(dev, BHASH0, bp->hash_table_mask[3]); 	/* bits 63 - 48 */
 
-	pWord16 = (unsigned short *)dev->dev_addr;
+	pWord16 = (const unsigned short *)dev->dev_addr;
 	bmwrite(dev, MADD0, *pWord16++);
 	bmwrite(dev, MADD1, *pWord16++);
 	bmwrite(dev, MADD2, *pWord16);
@@ -522,7 +522,7 @@
 {
 	struct bmac_data *bp = netdev_priv(dev);
 	unsigned char *p = addr;
-	unsigned short *pWord16;
+	const unsigned short *pWord16;
 	unsigned long flags;
 	int i;
 
@@ -533,7 +533,7 @@
 		dev->dev_addr[i] = p[i];
 	}
 	/* load up the hardware address */
-	pWord16  = (unsigned short *)dev->dev_addr;
+	pWord16  = (const unsigned short *)dev->dev_addr;
 	bmwrite(dev, MADD0, *pWord16++);
 	bmwrite(dev, MADD1, *pWord16++);
 	bmwrite(dev, MADD2, *pWord16);
@@ -1511,7 +1511,7 @@
 	i = bp->tx_empty;
 	++dev->stats.tx_errors;
 	if (i != bp->tx_fill) {
-		dev_kfree_skb(bp->tx_bufs[i]);
+		dev_kfree_skb_irq(bp->tx_bufs[i]);
 		bp->tx_bufs[i] = NULL;
 		if (++i >= N_TX_RING) i = 0;
 		bp->tx_empty = i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/apple/mace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/apple/mace.c
@@ -841,7 +841,7 @@
     if (mp->tx_bad_runt) {
 	mp->tx_bad_runt = 0;
     } else if (i != mp->tx_fill) {
-	dev_kfree_skb(mp->tx_bufs[i]);
+	dev_kfree_skb_irq(mp->tx_bufs[i]);
 	if (++i >= N_TX_RING)
 	    i = 0;
 	mp->tx_empty = i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_common.h
@@ -40,10 +40,12 @@
 
 #define AQ_DEVICE_ID_AQC113DEV	0x00C0
 #define AQ_DEVICE_ID_AQC113CS	0x94C0
+#define AQ_DEVICE_ID_AQC113CA	0x34C0
 #define AQ_DEVICE_ID_AQC114CS	0x93C0
 #define AQ_DEVICE_ID_AQC113	0x04C0
 #define AQ_DEVICE_ID_AQC113C	0x14C0
 #define AQ_DEVICE_ID_AQC115C	0x12C0
+#define AQ_DEVICE_ID_AQC116C	0x11C0
 
 #define HW_ATL_NIC_NAME "Marvell (aQuantia) AQtion 10Gbit Network Adapter"
 
@@ -53,20 +55,19 @@
 
 #define AQ_NIC_RATE_10G		BIT(0)
 #define AQ_NIC_RATE_5G		BIT(1)
-#define AQ_NIC_RATE_5GSR	BIT(2)
-#define AQ_NIC_RATE_2G5		BIT(3)
-#define AQ_NIC_RATE_1G		BIT(4)
-#define AQ_NIC_RATE_100M	BIT(5)
-#define AQ_NIC_RATE_10M		BIT(6)
-#define AQ_NIC_RATE_1G_HALF	BIT(7)
-#define AQ_NIC_RATE_100M_HALF	BIT(8)
-#define AQ_NIC_RATE_10M_HALF	BIT(9)
+#define AQ_NIC_RATE_2G5		BIT(2)
+#define AQ_NIC_RATE_1G		BIT(3)
+#define AQ_NIC_RATE_100M	BIT(4)
+#define AQ_NIC_RATE_10M		BIT(5)
+#define AQ_NIC_RATE_1G_HALF	BIT(6)
+#define AQ_NIC_RATE_100M_HALF	BIT(7)
+#define AQ_NIC_RATE_10M_HALF	BIT(8)
 
-#define AQ_NIC_RATE_EEE_10G	BIT(10)
-#define AQ_NIC_RATE_EEE_5G	BIT(11)
-#define AQ_NIC_RATE_EEE_2G5	BIT(12)
-#define AQ_NIC_RATE_EEE_1G	BIT(13)
-#define AQ_NIC_RATE_EEE_100M	BIT(14)
+#define AQ_NIC_RATE_EEE_10G	BIT(9)
+#define AQ_NIC_RATE_EEE_5G	BIT(10)
+#define AQ_NIC_RATE_EEE_2G5	BIT(11)
+#define AQ_NIC_RATE_EEE_1G	BIT(12)
+#define AQ_NIC_RATE_EEE_100M	BIT(13)
 #define AQ_NIC_RATE_EEE_MSK     (AQ_NIC_RATE_EEE_10G |\
 				 AQ_NIC_RATE_EEE_5G |\
 				 AQ_NIC_RATE_EEE_2G5 |\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c
@@ -13,6 +13,7 @@
 #include "aq_ptp.h"
 #include "aq_filters.h"
 #include "aq_macsec.h"
+#include "aq_main.h"
 
 #include <linux/ptp_clock_kernel.h>
 
@@ -255,7 +256,7 @@
 		const int rx_stat_cnt = ARRAY_SIZE(aq_ethtool_queue_rx_stat_names);
 		const int tx_stat_cnt = ARRAY_SIZE(aq_ethtool_queue_tx_stat_names);
 		char tc_string[8];
-		int tc;
+		unsigned int tc;
 
 		memset(tc_string, 0, sizeof(tc_string));
 		memcpy(p, aq_ethtool_stat_names,
@@ -264,7 +265,7 @@
 
 		for (tc = 0; tc < cfg->tcs; tc++) {
 			if (cfg->is_qos)
-				snprintf(tc_string, 8, "TC%d ", tc);
+				snprintf(tc_string, 8, "TC%u ", tc);
 
 			for (i = 0; i < cfg->vecs; i++) {
 				for (si = 0; si < rx_stat_cnt; si++) {
@@ -845,7 +846,7 @@
 
 	if (netif_running(ndev)) {
 		ndev_running = true;
-		dev_close(ndev);
+		aq_ndev_close(ndev);
 	}
 
 	cfg->rxds = max(ring->rx_pending, hw_caps->rxds_min);
@@ -861,7 +862,7 @@
 		goto err_exit;
 
 	if (ndev_running)
-		err = dev_open(ndev, NULL);
+		err = aq_ndev_open(ndev);
 
 err_exit:
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_hw.h
@@ -80,6 +80,8 @@
 };
 
 struct aq_stats_s {
+	u64 brc;
+	u64 btc;
 	u64 uprc;
 	u64 mprc;
 	u64 bprc;
@@ -217,7 +219,7 @@
 	int (*hw_ring_tx_head_update)(struct aq_hw_s *self,
 				      struct aq_ring_s *aq_ring);
 
-	int (*hw_set_mac_address)(struct aq_hw_s *self, u8 *mac_addr);
+	int (*hw_set_mac_address)(struct aq_hw_s *self, const u8 *mac_addr);
 
 	int (*hw_soft_reset)(struct aq_hw_s *self);
 
@@ -226,7 +228,7 @@
 
 	int (*hw_reset)(struct aq_hw_s *self);
 
-	int (*hw_init)(struct aq_hw_s *self, u8 *mac_addr);
+	int (*hw_init)(struct aq_hw_s *self, const u8 *mac_addr);
 
 	int (*hw_start)(struct aq_hw_s *self);
 
@@ -373,7 +375,7 @@
 	int (*set_phyloopback)(struct aq_hw_s *self, u32 mode, bool enable);
 
 	int (*set_power)(struct aq_hw_s *self, unsigned int power_state,
-			 u8 *mac);
+			 const u8 *mac);
 
 	int (*send_fw_request)(struct aq_hw_s *self,
 			       const struct hw_fw_request_iface *fw_req,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_macsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_macsec.c
@@ -35,7 +35,7 @@
 static int aq_apply_secy_cfg(struct aq_nic_s *nic,
 			     const struct macsec_secy *secy);
 
-static void aq_ether_addr_to_mac(u32 mac[2], unsigned char *emac)
+static void aq_ether_addr_to_mac(u32 mac[2], const unsigned char *emac)
 {
 	u32 tmp[2] = { 0 };
 
@@ -585,6 +585,7 @@
 
 	ret = aq_mss_set_egress_sakey_record(hw, &key_rec, sa_idx);
 
+	memzero_explicit(&key_rec, sizeof(key_rec));
 	return ret;
 }
 
@@ -932,6 +933,7 @@
 
 	ret = aq_mss_set_ingress_sakey_record(hw, &sa_key_record, sa_idx);
 
+	memzero_explicit(&sa_key_record, sizeof(sa_key_record));
 	return ret;
 }
 
@@ -1451,26 +1453,57 @@
 			egress_sa_threshold_expired);
 }
 
+#define AQ_LOCKED_MDO_DEF(mdo)						\
+static int aq_locked_mdo_##mdo(struct macsec_context *ctx)		\
+{									\
+	struct aq_nic_s *nic = netdev_priv(ctx->netdev);		\
+	int ret;							\
+	mutex_lock(&nic->macsec_mutex);					\
+	ret = aq_mdo_##mdo(ctx);					\
+	mutex_unlock(&nic->macsec_mutex);				\
+	return ret;							\
+}
+
+AQ_LOCKED_MDO_DEF(dev_open)
+AQ_LOCKED_MDO_DEF(dev_stop)
+AQ_LOCKED_MDO_DEF(add_secy)
+AQ_LOCKED_MDO_DEF(upd_secy)
+AQ_LOCKED_MDO_DEF(del_secy)
+AQ_LOCKED_MDO_DEF(add_rxsc)
+AQ_LOCKED_MDO_DEF(upd_rxsc)
+AQ_LOCKED_MDO_DEF(del_rxsc)
+AQ_LOCKED_MDO_DEF(add_rxsa)
+AQ_LOCKED_MDO_DEF(upd_rxsa)
+AQ_LOCKED_MDO_DEF(del_rxsa)
+AQ_LOCKED_MDO_DEF(add_txsa)
+AQ_LOCKED_MDO_DEF(upd_txsa)
+AQ_LOCKED_MDO_DEF(del_txsa)
+AQ_LOCKED_MDO_DEF(get_dev_stats)
+AQ_LOCKED_MDO_DEF(get_tx_sc_stats)
+AQ_LOCKED_MDO_DEF(get_tx_sa_stats)
+AQ_LOCKED_MDO_DEF(get_rx_sc_stats)
+AQ_LOCKED_MDO_DEF(get_rx_sa_stats)
+
 const struct macsec_ops aq_macsec_ops = {
-	.mdo_dev_open = aq_mdo_dev_open,
-	.mdo_dev_stop = aq_mdo_dev_stop,
-	.mdo_add_secy = aq_mdo_add_secy,
-	.mdo_upd_secy = aq_mdo_upd_secy,
-	.mdo_del_secy = aq_mdo_del_secy,
-	.mdo_add_rxsc = aq_mdo_add_rxsc,
-	.mdo_upd_rxsc = aq_mdo_upd_rxsc,
-	.mdo_del_rxsc = aq_mdo_del_rxsc,
-	.mdo_add_rxsa = aq_mdo_add_rxsa,
-	.mdo_upd_rxsa = aq_mdo_upd_rxsa,
-	.mdo_del_rxsa = aq_mdo_del_rxsa,
-	.mdo_add_txsa = aq_mdo_add_txsa,
-	.mdo_upd_txsa = aq_mdo_upd_txsa,
-	.mdo_del_txsa = aq_mdo_del_txsa,
-	.mdo_get_dev_stats = aq_mdo_get_dev_stats,
-	.mdo_get_tx_sc_stats = aq_mdo_get_tx_sc_stats,
-	.mdo_get_tx_sa_stats = aq_mdo_get_tx_sa_stats,
-	.mdo_get_rx_sc_stats = aq_mdo_get_rx_sc_stats,
-	.mdo_get_rx_sa_stats = aq_mdo_get_rx_sa_stats,
+	.mdo_dev_open = aq_locked_mdo_dev_open,
+	.mdo_dev_stop = aq_locked_mdo_dev_stop,
+	.mdo_add_secy = aq_locked_mdo_add_secy,
+	.mdo_upd_secy = aq_locked_mdo_upd_secy,
+	.mdo_del_secy = aq_locked_mdo_del_secy,
+	.mdo_add_rxsc = aq_locked_mdo_add_rxsc,
+	.mdo_upd_rxsc = aq_locked_mdo_upd_rxsc,
+	.mdo_del_rxsc = aq_locked_mdo_del_rxsc,
+	.mdo_add_rxsa = aq_locked_mdo_add_rxsa,
+	.mdo_upd_rxsa = aq_locked_mdo_upd_rxsa,
+	.mdo_del_rxsa = aq_locked_mdo_del_rxsa,
+	.mdo_add_txsa = aq_locked_mdo_add_txsa,
+	.mdo_upd_txsa = aq_locked_mdo_upd_txsa,
+	.mdo_del_txsa = aq_locked_mdo_del_txsa,
+	.mdo_get_dev_stats = aq_locked_mdo_get_dev_stats,
+	.mdo_get_tx_sc_stats = aq_locked_mdo_get_tx_sc_stats,
+	.mdo_get_tx_sa_stats = aq_locked_mdo_get_tx_sa_stats,
+	.mdo_get_rx_sc_stats = aq_locked_mdo_get_rx_sc_stats,
+	.mdo_get_rx_sa_stats = aq_locked_mdo_get_rx_sa_stats,
 };
 
 int aq_macsec_init(struct aq_nic_s *nic)
@@ -1492,6 +1525,7 @@
 
 	nic->ndev->features |= NETIF_F_HW_MACSEC;
 	nic->ndev->macsec_ops = &aq_macsec_ops;
+	mutex_init(&nic->macsec_mutex);
 
 	return 0;
 }
@@ -1515,7 +1549,7 @@
 	if (!nic->macsec_cfg)
 		return 0;
 
-	rtnl_lock();
+	mutex_lock(&nic->macsec_mutex);
 
 	if (nic->aq_fw_ops->send_macsec_req) {
 		struct macsec_cfg_request cfg = { 0 };
@@ -1564,7 +1598,7 @@
 	ret = aq_apply_macsec_cfg(nic);
 
 unlock:
-	rtnl_unlock();
+	mutex_unlock(&nic->macsec_mutex);
 	return ret;
 }
 
@@ -1576,9 +1610,9 @@
 	if (!netif_carrier_ok(nic->ndev))
 		return;
 
-	rtnl_lock();
+	mutex_lock(&nic->macsec_mutex);
 	aq_check_txsa_expiration(nic);
-	rtnl_unlock();
+	mutex_unlock(&nic->macsec_mutex);
 }
 
 int aq_macsec_rx_sa_cnt(struct aq_nic_s *nic)
@@ -1589,21 +1623,30 @@
 	if (!cfg)
 		return 0;
 
+	mutex_lock(&nic->macsec_mutex);
+
 	for (i = 0; i < AQ_MACSEC_MAX_SC; i++) {
 		if (!test_bit(i, &cfg->rxsc_idx_busy))
 			continue;
 		cnt += hweight_long(cfg->aq_rxsc[i].rx_sa_idx_busy);
 	}
 
+	mutex_unlock(&nic->macsec_mutex);
 	return cnt;
 }
 
 int aq_macsec_tx_sc_cnt(struct aq_nic_s *nic)
 {
+	int cnt;
+
 	if (!nic->macsec_cfg)
 		return 0;
 
-	return hweight_long(nic->macsec_cfg->txsc_idx_busy);
+	mutex_lock(&nic->macsec_mutex);
+	cnt = hweight_long(nic->macsec_cfg->txsc_idx_busy);
+	mutex_unlock(&nic->macsec_mutex);
+
+	return cnt;
 }
 
 int aq_macsec_tx_sa_cnt(struct aq_nic_s *nic)
@@ -1614,12 +1657,15 @@
 	if (!cfg)
 		return 0;
 
+	mutex_lock(&nic->macsec_mutex);
+
 	for (i = 0; i < AQ_MACSEC_MAX_SC; i++) {
 		if (!test_bit(i, &cfg->txsc_idx_busy))
 			continue;
 		cnt += hweight_long(cfg->aq_txsc[i].tx_sa_idx_busy);
 	}
 
+	mutex_unlock(&nic->macsec_mutex);
 	return cnt;
 }
 
@@ -1691,6 +1737,8 @@
 	if (!cfg)
 		return data;
 
+	mutex_lock(&nic->macsec_mutex);
+
 	aq_macsec_update_stats(nic);
 
 	common_stats = &cfg->stats;
@@ -1773,5 +1821,7 @@
 
 	data += i;
 
+	mutex_unlock(&nic->macsec_mutex);
+
 	return data;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_main.c
@@ -53,7 +53,7 @@
 	return ndev;
 }
 
-static int aq_ndev_open(struct net_device *ndev)
+int aq_ndev_open(struct net_device *ndev)
 {
 	struct aq_nic_s *aq_nic = netdev_priv(ndev);
 	int err = 0;
@@ -83,17 +83,14 @@
 	return err;
 }
 
-static int aq_ndev_close(struct net_device *ndev)
+int aq_ndev_close(struct net_device *ndev)
 {
 	struct aq_nic_s *aq_nic = netdev_priv(ndev);
 	int err = 0;
 
 	err = aq_nic_stop(aq_nic);
-	if (err < 0)
-		goto err_exit;
 	aq_nic_deinit(aq_nic, true);
 
-err_exit:
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_main.h
@@ -14,5 +14,7 @@
 
 void aq_ndev_schedule_work(struct work_struct *work);
 struct net_device *aq_ndev_alloc(void);
+int aq_ndev_open(struct net_device *ndev);
+int aq_ndev_close(struct net_device *ndev);
 
 #endif /* AQ_MAIN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
@@ -265,12 +265,10 @@
 static void aq_nic_polling_timer_cb(struct timer_list *t)
 {
 	struct aq_nic_s *self = from_timer(self, t, polling_timer);
-	struct aq_vec_s *aq_vec = NULL;
 	unsigned int i = 0U;
 
-	for (i = 0U, aq_vec = self->aq_vec[0];
-		self->aq_vecs > i; ++i, aq_vec = self->aq_vec[i])
-		aq_vec_isr(i, (void *)aq_vec);
+	for (i = 0U; self->aq_vecs > i; ++i)
+		aq_vec_isr(i, (void *)self->aq_vec[i]);
 
 	mod_timer(&self->polling_timer, jiffies +
 		  AQ_CFG_POLLING_TIMER_INTERVAL);
@@ -332,7 +330,7 @@
 	{
 		static u8 mac_addr_permanent[] = AQ_CFG_MAC_ADDR_PERMANENT;
 
-		ether_addr_copy(self->ndev->dev_addr, mac_addr_permanent);
+		eth_hw_addr_set(self->ndev, mac_addr_permanent);
 	}
 #endif
 
@@ -480,8 +478,8 @@
 	if (err < 0)
 		goto err_exit;
 
-	for (i = 0U, aq_vec = self->aq_vec[0];
-		self->aq_vecs > i; ++i, aq_vec = self->aq_vec[i]) {
+	for (i = 0U; self->aq_vecs > i; ++i) {
+		aq_vec = self->aq_vec[i];
 		err = aq_vec_start(aq_vec);
 		if (err < 0)
 			goto err_exit;
@@ -511,8 +509,8 @@
 		mod_timer(&self->polling_timer, jiffies +
 			  AQ_CFG_POLLING_TIMER_INTERVAL);
 	} else {
-		for (i = 0U, aq_vec = self->aq_vec[0];
-			self->aq_vecs > i; ++i, aq_vec = self->aq_vec[i]) {
+		for (i = 0U; self->aq_vecs > i; ++i) {
+			aq_vec = self->aq_vec[i];
 			err = aq_pci_func_alloc_irq(self, i, self->ndev->name,
 						    aq_vec_isr, aq_vec,
 						    aq_vec_get_affinity_mask(aq_vec));
@@ -872,7 +870,6 @@
 
 u64 *aq_nic_get_stats(struct aq_nic_s *self, u64 *data)
 {
-	struct aq_vec_s *aq_vec = NULL;
 	struct aq_stats_s *stats;
 	unsigned int count = 0U;
 	unsigned int i = 0U;
@@ -903,8 +900,14 @@
 	data[++i] = stats->mbtc;
 	data[++i] = stats->bbrc;
 	data[++i] = stats->bbtc;
-	data[++i] = stats->ubrc + stats->mbrc + stats->bbrc;
-	data[++i] = stats->ubtc + stats->mbtc + stats->bbtc;
+	if (stats->brc)
+		data[++i] = stats->brc;
+	else
+		data[++i] = stats->ubrc + stats->mbrc + stats->bbrc;
+	if (stats->btc)
+		data[++i] = stats->btc;
+	else
+		data[++i] = stats->ubtc + stats->mbtc + stats->bbtc;
 	data[++i] = stats->dma_pkt_rc;
 	data[++i] = stats->dma_pkt_tc;
 	data[++i] = stats->dma_oct_rc;
@@ -916,11 +919,11 @@
 	data += i;
 
 	for (tc = 0U; tc < self->aq_nic_cfg.tcs; tc++) {
-		for (i = 0U, aq_vec = self->aq_vec[0];
-		     aq_vec && self->aq_vecs > i;
-		     ++i, aq_vec = self->aq_vec[i]) {
+		for (i = 0U; self->aq_vecs > i; ++i) {
+			if (!self->aq_vec[i])
+				break;
 			data += count;
-			count = aq_vec_get_sw_stats(aq_vec, tc, data);
+			count = aq_vec_get_sw_stats(self->aq_vec[i], tc, data);
 		}
 	}
 
@@ -1234,7 +1237,6 @@
 
 int aq_nic_stop(struct aq_nic_s *self)
 {
-	struct aq_vec_s *aq_vec = NULL;
 	unsigned int i = 0U;
 
 	netif_tx_disable(self->ndev);
@@ -1252,9 +1254,8 @@
 
 	aq_ptp_irq_free(self);
 
-	for (i = 0U, aq_vec = self->aq_vec[0];
-		self->aq_vecs > i; ++i, aq_vec = self->aq_vec[i])
-		aq_vec_stop(aq_vec);
+	for (i = 0U; self->aq_vecs > i; ++i)
+		aq_vec_stop(self->aq_vec[i]);
 
 	aq_ptp_ring_stop(self);
 
@@ -1293,7 +1294,9 @@
 	aq_ptp_ring_free(self);
 	aq_ptp_free(self);
 
-	if (likely(self->aq_fw_ops->deinit) && link_down) {
+	/* May be invoked during hot unplug. */
+	if (pci_device_is_present(self->pdev) &&
+	    likely(self->aq_fw_ops->deinit) && link_down) {
 		mutex_lock(&self->fwreq_mutex);
 		self->aq_fw_ops->deinit(self->aq_hw);
 		mutex_unlock(&self->fwreq_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_nic.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_nic.h
@@ -154,6 +154,8 @@
 	struct mutex fwreq_mutex;
 #if IS_ENABLED(CONFIG_MACSEC)
 	struct aq_macsec_cfg *macsec_cfg;
+	/* mutex to protect data in macsec_cfg */
+	struct mutex macsec_mutex;
 #endif
 	/* PTP support */
 	struct aq_ptp_s *aq_ptp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c
@@ -49,6 +49,8 @@
 	{ PCI_VDEVICE(AQUANTIA, AQ_DEVICE_ID_AQC113), },
 	{ PCI_VDEVICE(AQUANTIA, AQ_DEVICE_ID_AQC113C), },
 	{ PCI_VDEVICE(AQUANTIA, AQ_DEVICE_ID_AQC115C), },
+	{ PCI_VDEVICE(AQUANTIA, AQ_DEVICE_ID_AQC113CA), },
+	{ PCI_VDEVICE(AQUANTIA, AQ_DEVICE_ID_AQC116C), },
 
 	{}
 };
@@ -85,7 +87,10 @@
 	{ AQ_DEVICE_ID_AQC113CS,	AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc113, },
 	{ AQ_DEVICE_ID_AQC114CS,	AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc113, },
 	{ AQ_DEVICE_ID_AQC113C,		AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc113, },
-	{ AQ_DEVICE_ID_AQC115C,		AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc113, },
+	{ AQ_DEVICE_ID_AQC115C,		AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc115c, },
+	{ AQ_DEVICE_ID_AQC113CA,	AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc113, },
+	{ AQ_DEVICE_ID_AQC116C,		AQ_HWREV_ANY,	&hw_atl2_ops, &hw_atl2_caps_aqc116c, },
+
 };
 
 MODULE_DEVICE_TABLE(pci, aq_pci_tbl);
@@ -374,7 +379,7 @@
 	}
 }
 
-static int aq_suspend_common(struct device *dev, bool deep)
+static int aq_suspend_common(struct device *dev)
 {
 	struct aq_nic_s *nic = pci_get_drvdata(to_pci_dev(dev));
 
@@ -387,17 +392,15 @@
 	if (netif_running(nic->ndev))
 		aq_nic_stop(nic);
 
-	if (deep) {
-		aq_nic_deinit(nic, !nic->aq_hw->aq_nic_cfg->wol);
-		aq_nic_set_power(nic);
-	}
+	aq_nic_deinit(nic, !nic->aq_hw->aq_nic_cfg->wol);
+	aq_nic_set_power(nic);
 
 	rtnl_unlock();
 
 	return 0;
 }
 
-static int atl_resume_common(struct device *dev, bool deep)
+static int atl_resume_common(struct device *dev)
 {
 	struct pci_dev *pdev = to_pci_dev(dev);
 	struct aq_nic_s *nic;
@@ -410,11 +413,6 @@
 	pci_set_power_state(pdev, PCI_D0);
 	pci_restore_state(pdev);
 
-	if (deep) {
-		/* Reinitialize Nic/Vecs objects */
-		aq_nic_deinit(nic, !nic->aq_hw->aq_nic_cfg->wol);
-	}
-
 	if (netif_running(nic->ndev)) {
 		ret = aq_nic_init(nic);
 		if (ret)
@@ -439,22 +437,22 @@
 
 static int aq_pm_freeze(struct device *dev)
 {
-	return aq_suspend_common(dev, false);
+	return aq_suspend_common(dev);
 }
 
 static int aq_pm_suspend_poweroff(struct device *dev)
 {
-	return aq_suspend_common(dev, true);
+	return aq_suspend_common(dev);
 }
 
 static int aq_pm_thaw(struct device *dev)
 {
-	return atl_resume_common(dev, false);
+	return atl_resume_common(dev);
 }
 
 static int aq_pm_resume_restore(struct device *dev)
 {
-	return atl_resume_common(dev, true);
+	return atl_resume_common(dev);
 }
 
 static const struct dev_pm_ops aq_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_ptp.c
@@ -953,8 +953,6 @@
 {
 	struct aq_ptp_s *aq_ptp = aq_nic->aq_ptp;
 	unsigned int tx_ring_idx, rx_ring_idx;
-	struct aq_ring_s *hwts;
-	struct aq_ring_s *ring;
 	int err;
 
 	if (!aq_ptp)
@@ -962,29 +960,23 @@
 
 	tx_ring_idx = aq_ptp_ring_idx(aq_nic->aq_nic_cfg.tc_mode);
 
-	ring = aq_ring_tx_alloc(&aq_ptp->ptp_tx, aq_nic,
-				tx_ring_idx, &aq_nic->aq_nic_cfg);
-	if (!ring) {
-		err = -ENOMEM;
+	err = aq_ring_tx_alloc(&aq_ptp->ptp_tx, aq_nic,
+			       tx_ring_idx, &aq_nic->aq_nic_cfg);
+	if (err)
 		goto err_exit;
-	}
 
 	rx_ring_idx = aq_ptp_ring_idx(aq_nic->aq_nic_cfg.tc_mode);
 
-	ring = aq_ring_rx_alloc(&aq_ptp->ptp_rx, aq_nic,
-				rx_ring_idx, &aq_nic->aq_nic_cfg);
-	if (!ring) {
-		err = -ENOMEM;
+	err = aq_ring_rx_alloc(&aq_ptp->ptp_rx, aq_nic,
+			       rx_ring_idx, &aq_nic->aq_nic_cfg);
+	if (err)
 		goto err_exit_ptp_tx;
-	}
 
-	hwts = aq_ring_hwts_rx_alloc(&aq_ptp->hwts_rx, aq_nic, PTP_HWST_RING_IDX,
-				     aq_nic->aq_nic_cfg.rxds,
-				     aq_nic->aq_nic_cfg.aq_hw_caps->rxd_size);
-	if (!hwts) {
-		err = -ENOMEM;
+	err = aq_ring_hwts_rx_alloc(&aq_ptp->hwts_rx, aq_nic, PTP_HWST_RING_IDX,
+				    aq_nic->aq_nic_cfg.rxds,
+				    aq_nic->aq_nic_cfg.aq_hw_caps->rxd_size);
+	if (err)
 		goto err_exit_ptp_rx;
-	}
 
 	err = aq_ptp_skb_ring_init(&aq_ptp->skb_ring, aq_nic->aq_nic_cfg.rxds);
 	if (err != 0) {
@@ -1001,7 +993,7 @@
 	return 0;
 
 err_exit_hwts_rx:
-	aq_ring_free(&aq_ptp->hwts_rx);
+	aq_ring_hwts_rx_free(&aq_ptp->hwts_rx);
 err_exit_ptp_rx:
 	aq_ring_free(&aq_ptp->ptp_rx);
 err_exit_ptp_tx:
@@ -1019,7 +1011,7 @@
 
 	aq_ring_free(&aq_ptp->ptp_tx);
 	aq_ring_free(&aq_ptp->ptp_rx);
-	aq_ring_free(&aq_ptp->hwts_rx);
+	aq_ring_hwts_rx_free(&aq_ptp->hwts_rx);
 
 	aq_ptp_skb_ring_release(&aq_ptp->skb_ring);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_ring.c
@@ -105,8 +105,8 @@
 	return 0;
 }
 
-static struct aq_ring_s *aq_ring_alloc(struct aq_ring_s *self,
-				       struct aq_nic_s *aq_nic)
+static int aq_ring_alloc(struct aq_ring_s *self,
+			 struct aq_nic_s *aq_nic)
 {
 	int err = 0;
 
@@ -128,46 +128,29 @@
 err_exit:
 	if (err < 0) {
 		aq_ring_free(self);
-		self = NULL;
 	}
 
-	return self;
+	return err;
 }
 
-struct aq_ring_s *aq_ring_tx_alloc(struct aq_ring_s *self,
-				   struct aq_nic_s *aq_nic,
-				   unsigned int idx,
-				   struct aq_nic_cfg_s *aq_nic_cfg)
+int aq_ring_tx_alloc(struct aq_ring_s *self,
+		     struct aq_nic_s *aq_nic,
+		     unsigned int idx,
+		     struct aq_nic_cfg_s *aq_nic_cfg)
 {
-	int err = 0;
-
 	self->aq_nic = aq_nic;
 	self->idx = idx;
 	self->size = aq_nic_cfg->txds;
 	self->dx_size = aq_nic_cfg->aq_hw_caps->txd_size;
 
-	self = aq_ring_alloc(self, aq_nic);
-	if (!self) {
-		err = -ENOMEM;
-		goto err_exit;
-	}
-
-err_exit:
-	if (err < 0) {
-		aq_ring_free(self);
-		self = NULL;
-	}
-
-	return self;
+	return aq_ring_alloc(self, aq_nic);
 }
 
-struct aq_ring_s *aq_ring_rx_alloc(struct aq_ring_s *self,
-				   struct aq_nic_s *aq_nic,
-				   unsigned int idx,
-				   struct aq_nic_cfg_s *aq_nic_cfg)
+int aq_ring_rx_alloc(struct aq_ring_s *self,
+		     struct aq_nic_s *aq_nic,
+		     unsigned int idx,
+		     struct aq_nic_cfg_s *aq_nic_cfg)
 {
-	int err = 0;
-
 	self->aq_nic = aq_nic;
 	self->idx = idx;
 	self->size = aq_nic_cfg->rxds;
@@ -178,22 +161,10 @@
 	if (aq_nic_cfg->rxpageorder > self->page_order)
 		self->page_order = aq_nic_cfg->rxpageorder;
 
-	self = aq_ring_alloc(self, aq_nic);
-	if (!self) {
-		err = -ENOMEM;
-		goto err_exit;
-	}
-
-err_exit:
-	if (err < 0) {
-		aq_ring_free(self);
-		self = NULL;
-	}
-
-	return self;
+	return aq_ring_alloc(self, aq_nic);
 }
 
-struct aq_ring_s *
+int
 aq_ring_hwts_rx_alloc(struct aq_ring_s *self, struct aq_nic_s *aq_nic,
 		      unsigned int idx, unsigned int size, unsigned int dx_size)
 {
@@ -211,10 +182,10 @@
 					   GFP_KERNEL);
 	if (!self->dx_ring) {
 		aq_ring_free(self);
-		return NULL;
+		return -ENOMEM;
 	}
 
-	return self;
+	return 0;
 }
 
 int aq_ring_init(struct aq_ring_s *self, const enum atl_ring_type ring_type)
@@ -345,7 +316,6 @@
 		     int budget)
 {
 	struct net_device *ndev = aq_nic_get_ndev(self->aq_nic);
-	bool is_rsc_completed = true;
 	int err = 0;
 
 	for (; (self->sw_head != self->hw_head) && budget;
@@ -363,8 +333,17 @@
 			continue;
 
 		if (!buff->is_eop) {
+			unsigned int frag_cnt = 0U;
 			buff_ = buff;
 			do {
+				bool is_rsc_completed = true;
+
+				if (buff_->next >= self->size) {
+					err = -EIO;
+					goto err_exit;
+				}
+
+				frag_cnt++;
 				next_ = buff_->next,
 				buff_ = &self->buff_ring[next_];
 				is_rsc_completed =
@@ -372,22 +351,25 @@
 							    next_,
 							    self->hw_head);
 
-				if (unlikely(!is_rsc_completed))
-					break;
+				if (unlikely(!is_rsc_completed) ||
+						frag_cnt > MAX_SKB_FRAGS) {
+					err = 0;
+					goto err_exit;
+				}
 
 				buff->is_error |= buff_->is_error;
 				buff->is_cso_err |= buff_->is_cso_err;
 
 			} while (!buff_->is_eop);
 
-			if (!is_rsc_completed) {
-				err = 0;
-				goto err_exit;
-			}
 			if (buff->is_error ||
 			    (buff->is_lro && buff->is_cso_err)) {
 				buff_ = buff;
 				do {
+					if (buff_->next >= self->size) {
+						err = -EIO;
+						goto err_exit;
+					}
 					next_ = buff_->next,
 					buff_ = &self->buff_ring[next_];
 
@@ -437,7 +419,7 @@
 		       ALIGN(hdr_len, sizeof(long)));
 
 		if (buff->len - hdr_len > 0) {
-			skb_add_rx_frag(skb, 0, buff->rxdata.page,
+			skb_add_rx_frag(skb, i++, buff->rxdata.page,
 					buff->rxdata.pg_off + hdr_len,
 					buff->len - hdr_len,
 					AQ_CFG_RX_FRAME_MAX);
@@ -446,7 +428,6 @@
 
 		if (!buff->is_eop) {
 			buff_ = buff;
-			i = 1U;
 			do {
 				next_ = buff_->next;
 				buff_ = &self->buff_ring[next_];
@@ -567,11 +548,27 @@
 		return;
 
 	kfree(self->buff_ring);
+	self->buff_ring = NULL;
 
-	if (self->dx_ring)
+	if (self->dx_ring) {
 		dma_free_coherent(aq_nic_get_dev(self->aq_nic),
 				  self->size * self->dx_size, self->dx_ring,
 				  self->dx_ring_pa);
+		self->dx_ring = NULL;
+	}
+}
+
+void aq_ring_hwts_rx_free(struct aq_ring_s *self)
+{
+	if (!self)
+		return;
+
+	if (self->dx_ring) {
+		dma_free_coherent(aq_nic_get_dev(self->aq_nic),
+				  self->size * self->dx_size + AQ_CFG_RXDS_DEF,
+				  self->dx_ring, self->dx_ring_pa);
+		self->dx_ring = NULL;
+	}
 }
 
 unsigned int aq_ring_fill_stats_data(struct aq_ring_s *self, u64 *data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_ring.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_ring.h
@@ -167,14 +167,15 @@
 		self->sw_head - self->sw_tail - 1);
 }
 
-struct aq_ring_s *aq_ring_tx_alloc(struct aq_ring_s *self,
-				   struct aq_nic_s *aq_nic,
-				   unsigned int idx,
-				   struct aq_nic_cfg_s *aq_nic_cfg);
-struct aq_ring_s *aq_ring_rx_alloc(struct aq_ring_s *self,
-				   struct aq_nic_s *aq_nic,
-				   unsigned int idx,
-				   struct aq_nic_cfg_s *aq_nic_cfg);
+int aq_ring_tx_alloc(struct aq_ring_s *self,
+		     struct aq_nic_s *aq_nic,
+		     unsigned int idx,
+		     struct aq_nic_cfg_s *aq_nic_cfg);
+int aq_ring_rx_alloc(struct aq_ring_s *self,
+		     struct aq_nic_s *aq_nic,
+		     unsigned int idx,
+		     struct aq_nic_cfg_s *aq_nic_cfg);
+
 int aq_ring_init(struct aq_ring_s *self, const enum atl_ring_type ring_type);
 void aq_ring_rx_deinit(struct aq_ring_s *self);
 void aq_ring_free(struct aq_ring_s *self);
@@ -188,9 +189,10 @@
 		     int budget);
 int aq_ring_rx_fill(struct aq_ring_s *self);
 
-struct aq_ring_s *aq_ring_hwts_rx_alloc(struct aq_ring_s *self,
-		struct aq_nic_s *aq_nic, unsigned int idx,
-		unsigned int size, unsigned int dx_size);
+int aq_ring_hwts_rx_alloc(struct aq_ring_s *self,
+			  struct aq_nic_s *aq_nic, unsigned int idx,
+			  unsigned int size, unsigned int dx_size);
+void aq_ring_hwts_rx_free(struct aq_ring_s *self);
 void aq_ring_hwts_rx_clean(struct aq_ring_s *self, struct aq_nic_s *aq_nic);
 
 unsigned int aq_ring_fill_stats_data(struct aq_ring_s *self, u64 *data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/aq_vec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_vec.c
@@ -43,8 +43,8 @@
 	if (!self) {
 		err = -EINVAL;
 	} else {
-		for (i = 0U, ring = self->ring[0];
-			self->tx_rings > i; ++i, ring = self->ring[i]) {
+		for (i = 0U; self->tx_rings > i; ++i) {
+			ring = self->ring[i];
 			u64_stats_update_begin(&ring[AQ_VEC_RX_ID].stats.rx.syncp);
 			ring[AQ_VEC_RX_ID].stats.rx.polls++;
 			u64_stats_update_end(&ring[AQ_VEC_RX_ID].stats.rx.syncp);
@@ -142,21 +142,18 @@
 		const unsigned int idx_ring = AQ_NIC_CFG_TCVEC2RING(aq_nic_cfg,
 								    i, idx);
 
-		ring = aq_ring_tx_alloc(&self->ring[i][AQ_VEC_TX_ID], aq_nic,
-					idx_ring, aq_nic_cfg);
-		if (!ring) {
-			err = -ENOMEM;
+		ring = &self->ring[i][AQ_VEC_TX_ID];
+		err = aq_ring_tx_alloc(ring, aq_nic, idx_ring, aq_nic_cfg);
+		if (err)
 			goto err_exit;
-		}
 
 		++self->tx_rings;
 
 		aq_nic_set_tx_ring(aq_nic, idx_ring, ring);
 
-		ring = aq_ring_rx_alloc(&self->ring[i][AQ_VEC_RX_ID], aq_nic,
-					idx_ring, aq_nic_cfg);
-		if (!ring) {
-			err = -ENOMEM;
+		ring = &self->ring[i][AQ_VEC_RX_ID];
+		err = aq_ring_rx_alloc(ring, aq_nic, idx_ring, aq_nic_cfg);
+		if (err) {
 			goto err_exit;
 		}
 
@@ -182,8 +179,8 @@
 	self->aq_hw_ops = aq_hw_ops;
 	self->aq_hw = aq_hw;
 
-	for (i = 0U, ring = self->ring[0];
-		self->tx_rings > i; ++i, ring = self->ring[i]) {
+	for (i = 0U; self->tx_rings > i; ++i) {
+		ring = self->ring[i];
 		err = aq_ring_init(&ring[AQ_VEC_TX_ID], ATL_RING_TX);
 		if (err < 0)
 			goto err_exit;
@@ -224,8 +221,8 @@
 	unsigned int i = 0U;
 	int err = 0;
 
-	for (i = 0U, ring = self->ring[0];
-		self->tx_rings > i; ++i, ring = self->ring[i]) {
+	for (i = 0U; self->tx_rings > i; ++i) {
+		ring = self->ring[i];
 		err = self->aq_hw_ops->hw_ring_tx_start(self->aq_hw,
 							&ring[AQ_VEC_TX_ID]);
 		if (err < 0)
@@ -248,8 +245,8 @@
 	struct aq_ring_s *ring = NULL;
 	unsigned int i = 0U;
 
-	for (i = 0U, ring = self->ring[0];
-		self->tx_rings > i; ++i, ring = self->ring[i]) {
+	for (i = 0U; self->tx_rings > i; ++i) {
+		ring = self->ring[i];
 		self->aq_hw_ops->hw_ring_tx_stop(self->aq_hw,
 						 &ring[AQ_VEC_TX_ID]);
 
@@ -268,8 +265,8 @@
 	if (!self)
 		goto err_exit;
 
-	for (i = 0U, ring = self->ring[0];
-		self->tx_rings > i; ++i, ring = self->ring[i]) {
+	for (i = 0U; self->tx_rings > i; ++i) {
+		ring = self->ring[i];
 		aq_ring_tx_clean(&ring[AQ_VEC_TX_ID]);
 		aq_ring_rx_deinit(&ring[AQ_VEC_RX_ID]);
 	}
@@ -297,8 +294,8 @@
 	if (!self)
 		goto err_exit;
 
-	for (i = 0U, ring = self->ring[0];
-		self->tx_rings > i; ++i, ring = self->ring[i]) {
+	for (i = 0U; self->tx_rings > i; ++i) {
+		ring = self->ring[i];
 		aq_ring_free(&ring[AQ_VEC_TX_ID]);
 		if (i < self->rx_rings)
 			aq_ring_free(&ring[AQ_VEC_RX_ID]);
@@ -362,9 +359,6 @@
 {
 	unsigned int count;
 
-	WARN_ONCE(!aq_vec_is_valid_tc(self, tc),
-		  "Invalid tc %u (#rx=%u, #tx=%u)\n",
-		  tc, self->rx_rings, self->tx_rings);
 	if (!aq_vec_is_valid_tc(self, tc))
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_a0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_a0.c
@@ -322,7 +322,7 @@
 	return aq_hw_err_from_flags(self);
 }
 
-static int hw_atl_a0_hw_mac_addr_set(struct aq_hw_s *self, u8 *mac_addr)
+static int hw_atl_a0_hw_mac_addr_set(struct aq_hw_s *self, const u8 *mac_addr)
 {
 	unsigned int h = 0U;
 	unsigned int l = 0U;
@@ -348,7 +348,7 @@
 	return err;
 }
 
-static int hw_atl_a0_hw_init(struct aq_hw_s *self, u8 *mac_addr)
+static int hw_atl_a0_hw_init(struct aq_hw_s *self, const u8 *mac_addr)
 {
 	static u32 aq_hw_atl_igcr_table_[4][2] = {
 		[AQ_HW_IRQ_INVALID] = { 0x20000000U, 0x20000000U },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c
@@ -533,7 +533,7 @@
 	return aq_hw_err_from_flags(self);
 }
 
-int hw_atl_b0_hw_mac_addr_set(struct aq_hw_s *self, u8 *mac_addr)
+int hw_atl_b0_hw_mac_addr_set(struct aq_hw_s *self, const u8 *mac_addr)
 {
 	unsigned int h = 0U;
 	unsigned int l = 0U;
@@ -558,7 +558,7 @@
 	return err;
 }
 
-static int hw_atl_b0_hw_init(struct aq_hw_s *self, u8 *mac_addr)
+static int hw_atl_b0_hw_init(struct aq_hw_s *self, const u8 *mac_addr)
 {
 	static u32 aq_hw_atl_igcr_table_[4][2] = {
 		[AQ_HW_IRQ_INVALID] = { 0x20000000U, 0x20000000U },
@@ -889,6 +889,13 @@
 		err = -ENXIO;
 		goto err_exit;
 	}
+
+	/* Validate that the new hw_head_ is reasonable. */
+	if (hw_head_ >= ring->size) {
+		err = -ENXIO;
+		goto err_exit;
+	}
+
 	ring->hw_head = hw_head_;
 	err = aq_hw_err_from_flags(self);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.h
@@ -58,7 +58,7 @@
 
 void hw_atl_b0_hw_init_rx_rss_ctrl1(struct aq_hw_s *self);
 
-int hw_atl_b0_hw_mac_addr_set(struct aq_hw_s *self, u8 *mac_addr);
+int hw_atl_b0_hw_mac_addr_set(struct aq_hw_s *self, const u8 *mac_addr);
 
 int hw_atl_b0_set_fc(struct aq_hw_s *self, u32 fc, u32 tc);
 int hw_atl_b0_set_loopback(struct aq_hw_s *self, u32 mode, bool enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c
@@ -559,6 +559,11 @@
 			goto err_exit;
 
 		if (fw.len == 0xFFFFU) {
+			if (sw.len > sizeof(self->rpc)) {
+				printk(KERN_INFO "Invalid sw len: %x\n", sw.len);
+				err = -EINVAL;
+				goto err_exit;
+			}
 			err = hw_atl_utils_fw_rpc_call(self, sw.len);
 			if (err < 0)
 				goto err_exit;
@@ -567,6 +572,11 @@
 
 	if (rpc) {
 		if (fw.len) {
+			if (fw.len > sizeof(self->rpc)) {
+				printk(KERN_INFO "Invalid fw len: %x\n", fw.len);
+				err = -EINVAL;
+				goto err_exit;
+			}
 			err =
 			hw_atl_utils_fw_downld_dwords(self,
 						      self->rpc_addr,
@@ -857,12 +867,20 @@
 int hw_atl_utils_update_stats(struct aq_hw_s *self)
 {
 	struct aq_stats_s *cs = &self->curr_stats;
+	struct aq_stats_s curr_stats = *cs;
 	struct hw_atl_utils_mbox mbox;
+	bool corrupted_stats = false;
 
 	hw_atl_utils_mpi_read_stats(self, &mbox);
 
-#define AQ_SDELTA(_N_) (self->curr_stats._N_ += \
-			mbox.stats._N_ - self->last_stats._N_)
+#define AQ_SDELTA(_N_)  \
+do { \
+	if (!corrupted_stats && \
+	    ((s64)(mbox.stats._N_ - self->last_stats._N_)) >= 0) \
+		curr_stats._N_ += mbox.stats._N_ - self->last_stats._N_; \
+	else \
+		corrupted_stats = true; \
+} while (0)
 
 	if (self->aq_link_status.mbps) {
 		AQ_SDELTA(uprc);
@@ -882,6 +900,9 @@
 		AQ_SDELTA(bbrc);
 		AQ_SDELTA(bbtc);
 		AQ_SDELTA(dpc);
+
+		if (!corrupted_stats)
+			*cs = curr_stats;
 	}
 #undef AQ_SDELTA
 
@@ -944,7 +965,7 @@
 }
 
 static int aq_fw1x_set_wake_magic(struct aq_hw_s *self, bool wol_enabled,
-				  u8 *mac)
+				  const u8 *mac)
 {
 	struct hw_atl_utils_fw_rpc *prpc = NULL;
 	unsigned int rpc_size = 0U;
@@ -987,7 +1008,7 @@
 }
 
 static int aq_fw1x_set_power(struct aq_hw_s *self, unsigned int power_state,
-			     u8 *mac)
+			     const u8 *mac)
 {
 	struct hw_atl_utils_fw_rpc *prpc = NULL;
 	unsigned int rpc_size = 0U;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils_fw2x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils_fw2x.c
@@ -132,9 +132,6 @@
 	if (speed & AQ_NIC_RATE_5G)
 		rate |= FW2X_RATE_5G;
 
-	if (speed & AQ_NIC_RATE_5GSR)
-		rate |= FW2X_RATE_5G;
-
 	if (speed & AQ_NIC_RATE_2G5)
 		rate |= FW2X_RATE_2G5;
 
@@ -358,7 +355,7 @@
 	return 0;
 }
 
-static int aq_fw2x_set_wol(struct aq_hw_s *self, u8 *mac)
+static int aq_fw2x_set_wol(struct aq_hw_s *self, const u8 *mac)
 {
 	struct hw_atl_utils_fw_rpc *rpc = NULL;
 	struct offload_info *info = NULL;
@@ -404,7 +401,7 @@
 }
 
 static int aq_fw2x_set_power(struct aq_hw_s *self, unsigned int power_state,
-			     u8 *mac)
+			     const u8 *mac)
 {
 	int err = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2.c
@@ -65,11 +65,25 @@
 			  AQ_NIC_RATE_5G  |
 			  AQ_NIC_RATE_2G5 |
 			  AQ_NIC_RATE_1G  |
-			  AQ_NIC_RATE_1G_HALF   |
 			  AQ_NIC_RATE_100M      |
-			  AQ_NIC_RATE_100M_HALF |
-			  AQ_NIC_RATE_10M       |
-			  AQ_NIC_RATE_10M_HALF,
+			  AQ_NIC_RATE_10M,
+};
+
+const struct aq_hw_caps_s hw_atl2_caps_aqc115c = {
+	DEFAULT_BOARD_BASIC_CAPABILITIES,
+	.media_type = AQ_HW_MEDIA_TYPE_TP,
+	.link_speed_msk = AQ_NIC_RATE_2G5 |
+			  AQ_NIC_RATE_1G  |
+			  AQ_NIC_RATE_100M      |
+			  AQ_NIC_RATE_10M,
+};
+
+const struct aq_hw_caps_s hw_atl2_caps_aqc116c = {
+	DEFAULT_BOARD_BASIC_CAPABILITIES,
+	.media_type = AQ_HW_MEDIA_TYPE_TP,
+	.link_speed_msk = AQ_NIC_RATE_1G  |
+			  AQ_NIC_RATE_100M      |
+			  AQ_NIC_RATE_10M,
 };
 
 static u32 hw_atl2_sem_act_rslvr_get(struct aq_hw_s *self)
@@ -516,7 +530,7 @@
 	return aq_hw_err_from_flags(self);
 }
 
-static int hw_atl2_hw_init(struct aq_hw_s *self, u8 *mac_addr)
+static int hw_atl2_hw_init(struct aq_hw_s *self, const u8 *mac_addr)
 {
 	static u32 aq_hw_atl2_igcr_table_[4][2] = {
 		[AQ_HW_IRQ_INVALID] = { 0x20000000U, 0x20000000U },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2.h
@@ -9,6 +9,8 @@
 #include "aq_common.h"
 
 extern const struct aq_hw_caps_s hw_atl2_caps_aqc113;
+extern const struct aq_hw_caps_s hw_atl2_caps_aqc115c;
+extern const struct aq_hw_caps_s hw_atl2_caps_aqc116c;
 extern const struct aq_hw_ops hw_atl2_ops;
 
 #endif /* HW_ATL2_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2_utils.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2_utils.h
@@ -239,7 +239,8 @@
 		u8 minor;
 		u16 build;
 	} phy;
-	u32 rsvd;
+	u32 drv_iface_ver:4;
+	u32 rsvd:28;
 };
 
 struct link_status_s {
@@ -424,7 +425,7 @@
 	u16 rsvd2;
 };
 
-struct statistics_s {
+struct statistics_a0_s {
 	struct {
 		u32 link_up;
 		u32 link_down;
@@ -457,6 +458,33 @@
 	u32 reserve_fw_gap;
 };
 
+struct __packed statistics_b0_s {
+	u64 rx_good_octets;
+	u64 rx_pause_frames;
+	u64 rx_good_frames;
+	u64 rx_errors;
+	u64 rx_unicast_frames;
+	u64 rx_multicast_frames;
+	u64 rx_broadcast_frames;
+
+	u64 tx_good_octets;
+	u64 tx_pause_frames;
+	u64 tx_good_frames;
+	u64 tx_errors;
+	u64 tx_unicast_frames;
+	u64 tx_multicast_frames;
+	u64 tx_broadcast_frames;
+
+	u32 main_loop_cycles;
+};
+
+struct __packed statistics_s {
+	union __packed {
+		struct statistics_a0_s a0;
+		struct statistics_b0_s b0;
+	};
+};
+
 struct filter_caps_s {
 	u8 l2_filters_base_index:6;
 	u8 flexible_filter_mask:2;
@@ -545,7 +573,7 @@
 	u32 rsvd5;
 };
 
-struct fw_interface_out {
+struct __packed fw_interface_out {
 	struct transaction_counter_s transaction_id;
 	struct version_s version;
 	struct link_status_s link_status;
@@ -569,7 +597,6 @@
 	struct core_dump_s core_dump;
 	u32 rsvd11;
 	struct statistics_s stats;
-	u32 rsvd12;
 	struct filter_caps_s filter_caps;
 	struct device_caps_s device_caps;
 	u32 rsvd13;
@@ -592,6 +619,9 @@
 #define  AQ_HOST_MODE_LOW_POWER    3U
 #define  AQ_HOST_MODE_SHUTDOWN     4U
 
+#define  AQ_A2_FW_INTERFACE_A0     0
+#define  AQ_A2_FW_INTERFACE_B0     1
+
 int hw_atl2_utils_initfw(struct aq_hw_s *self, const struct aq_fw_ops **fw_ops);
 
 int hw_atl2_utils_soft_reset(struct aq_hw_s *self);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2_utils_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/hw_atl2/hw_atl2_utils_fw.c
@@ -84,7 +84,7 @@
 			if (cnt > AQ_A2_FW_READ_TRY_MAX)
 				return -ETIME;
 			if (tid1.transaction_cnt_a != tid1.transaction_cnt_b)
-				udelay(1);
+				mdelay(1);
 		} while (tid1.transaction_cnt_a != tid1.transaction_cnt_b);
 
 		hw_atl2_mif_shared_buf_read(self, offset, (u32 *)data, dwords);
@@ -154,7 +154,7 @@
 {
 	link_options->rate_10G = !!(speed & AQ_NIC_RATE_10G);
 	link_options->rate_5G = !!(speed & AQ_NIC_RATE_5G);
-	link_options->rate_N5G = !!(speed & AQ_NIC_RATE_5GSR);
+	link_options->rate_N5G = link_options->rate_5G;
 	link_options->rate_2P5G = !!(speed & AQ_NIC_RATE_2G5);
 	link_options->rate_N2P5G = link_options->rate_2P5G;
 	link_options->rate_1G = !!(speed & AQ_NIC_RATE_1G);
@@ -192,8 +192,6 @@
 		rate |= AQ_NIC_RATE_10G;
 	if (lkp_link_caps->rate_5G)
 		rate |= AQ_NIC_RATE_5G;
-	if (lkp_link_caps->rate_N5G)
-		rate |= AQ_NIC_RATE_5GSR;
 	if (lkp_link_caps->rate_2P5G)
 		rate |= AQ_NIC_RATE_2G5;
 	if (lkp_link_caps->rate_1G)
@@ -335,15 +333,22 @@
 	return 0;
 }
 
-static int aq_a2_fw_update_stats(struct aq_hw_s *self)
+static void aq_a2_fill_a0_stats(struct aq_hw_s *self,
+				struct statistics_s *stats)
 {
 	struct hw_atl2_priv *priv = (struct hw_atl2_priv *)self->priv;
-	struct statistics_s stats;
-
-	hw_atl2_shared_buffer_read_safe(self, stats, &stats);
-
-#define AQ_SDELTA(_N_, _F_) (self->curr_stats._N_ += \
-			stats.msm._F_ - priv->last_stats.msm._F_)
+	struct aq_stats_s *cs = &self->curr_stats;
+	struct aq_stats_s curr_stats = *cs;
+	bool corrupted_stats = false;
+
+#define AQ_SDELTA(_N, _F)  \
+do { \
+	if (!corrupted_stats && \
+	    ((s64)(stats->a0.msm._F - priv->last_stats.a0.msm._F)) >= 0) \
+		curr_stats._N += stats->a0.msm._F - priv->last_stats.a0.msm._F;\
+	else \
+		corrupted_stats = true; \
+} while (0)
 
 	if (self->aq_link_status.mbps) {
 		AQ_SDELTA(uprc, rx_unicast_frames);
@@ -362,17 +367,76 @@
 		AQ_SDELTA(mbtc, tx_multicast_octets);
 		AQ_SDELTA(bbrc, rx_broadcast_octets);
 		AQ_SDELTA(bbtc, tx_broadcast_octets);
+
+		if (!corrupted_stats)
+			*cs = curr_stats;
+	}
+#undef AQ_SDELTA
+
+}
+
+static void aq_a2_fill_b0_stats(struct aq_hw_s *self,
+				struct statistics_s *stats)
+{
+	struct hw_atl2_priv *priv = (struct hw_atl2_priv *)self->priv;
+	struct aq_stats_s *cs = &self->curr_stats;
+	struct aq_stats_s curr_stats = *cs;
+	bool corrupted_stats = false;
+
+#define AQ_SDELTA(_N, _F)  \
+do { \
+	if (!corrupted_stats && \
+	    ((s64)(stats->b0._F - priv->last_stats.b0._F)) >= 0) \
+		curr_stats._N += stats->b0._F - priv->last_stats.b0._F; \
+	else \
+		corrupted_stats = true; \
+} while (0)
+
+	if (self->aq_link_status.mbps) {
+		AQ_SDELTA(uprc, rx_unicast_frames);
+		AQ_SDELTA(mprc, rx_multicast_frames);
+		AQ_SDELTA(bprc, rx_broadcast_frames);
+		AQ_SDELTA(erpr, rx_errors);
+		AQ_SDELTA(brc, rx_good_octets);
+
+		AQ_SDELTA(uptc, tx_unicast_frames);
+		AQ_SDELTA(mptc, tx_multicast_frames);
+		AQ_SDELTA(bptc, tx_broadcast_frames);
+		AQ_SDELTA(erpt, tx_errors);
+		AQ_SDELTA(btc, tx_good_octets);
+
+		if (!corrupted_stats)
+			*cs = curr_stats;
 	}
 #undef AQ_SDELTA
-	self->curr_stats.dma_pkt_rc =
-		hw_atl_stats_rx_dma_good_pkt_counter_get(self);
-	self->curr_stats.dma_pkt_tc =
-		hw_atl_stats_tx_dma_good_pkt_counter_get(self);
-	self->curr_stats.dma_oct_rc =
-		hw_atl_stats_rx_dma_good_octet_counter_get(self);
-	self->curr_stats.dma_oct_tc =
-		hw_atl_stats_tx_dma_good_octet_counter_get(self);
-	self->curr_stats.dpc = hw_atl_rpb_rx_dma_drop_pkt_cnt_get(self);
+}
+
+static int aq_a2_fw_update_stats(struct aq_hw_s *self)
+{
+	struct hw_atl2_priv *priv = (struct hw_atl2_priv *)self->priv;
+	struct aq_stats_s *cs = &self->curr_stats;
+	struct statistics_s stats;
+	struct version_s version;
+	int err;
+
+	err = hw_atl2_shared_buffer_read_safe(self, version, &version);
+	if (err)
+		return err;
+
+	err = hw_atl2_shared_buffer_read_safe(self, stats, &stats);
+	if (err)
+		return err;
+
+	if (version.drv_iface_ver == AQ_A2_FW_INTERFACE_A0)
+		aq_a2_fill_a0_stats(self, &stats);
+	else
+		aq_a2_fill_b0_stats(self, &stats);
+
+	cs->dma_pkt_rc = hw_atl_stats_rx_dma_good_pkt_counter_get(self);
+	cs->dma_pkt_tc = hw_atl_stats_tx_dma_good_pkt_counter_get(self);
+	cs->dma_oct_rc = hw_atl_stats_rx_dma_good_octet_counter_get(self);
+	cs->dma_oct_tc = hw_atl_stats_tx_dma_good_octet_counter_get(self);
+	cs->dpc = hw_atl_rpb_rx_dma_drop_pkt_cnt_get(self);
 
 	memcpy(&priv->last_stats, &stats, sizeof(stats));
 
@@ -499,9 +563,9 @@
 	hw_atl2_shared_buffer_read_safe(self, version, &version);
 
 	/* A2 FW version is stored in reverse order */
-	return version.mac.major << 24 |
-	       version.mac.minor << 16 |
-	       version.mac.build;
+	return version.bundle.major << 24 |
+	       version.bundle.minor << 16 |
+	       version.bundle.build;
 }
 
 int hw_atl2_utils_get_action_resolve_table_caps(struct aq_hw_s *self,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/aquantia/atlantic/macsec/macsec_api.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/aquantia/atlantic/macsec/macsec_api.c
@@ -757,6 +757,7 @@
 			 u16 table_index)
 {
 	u16 packed_record[18];
+	int ret;
 
 	if (table_index >= NUMROWS_INGRESSSAKEYRECORD)
 		return -EINVAL;
@@ -789,9 +790,12 @@
 
 	packed_record[16] = rec->key_len & 0x3;
 
-	return set_raw_ingress_record(hw, packed_record, 18, 2,
-				      ROWOFFSET_INGRESSSAKEYRECORD +
-					      table_index);
+	ret = set_raw_ingress_record(hw, packed_record, 18, 2,
+				     ROWOFFSET_INGRESSSAKEYRECORD +
+				     table_index);
+
+	memzero_explicit(packed_record, sizeof(packed_record));
+	return ret;
 }
 
 int aq_mss_set_ingress_sakey_record(struct aq_hw_s *hw,
@@ -1739,14 +1743,14 @@
 	ret = set_raw_egress_record(hw, packed_record, 8, 2,
 				    ROWOFFSET_EGRESSSAKEYRECORD + table_index);
 	if (unlikely(ret))
-		return ret;
+		goto clear_key;
 	ret = set_raw_egress_record(hw, packed_record + 8, 8, 2,
 				    ROWOFFSET_EGRESSSAKEYRECORD + table_index -
 					    32);
-	if (unlikely(ret))
-		return ret;
 
-	return 0;
+clear_key:
+	memzero_explicit(packed_record, sizeof(packed_record));
+	return ret;
 }
 
 int aq_mss_set_egress_sakey_record(struct aq_hw_s *hw,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/arc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/arc/Kconfig
@@ -26,7 +26,7 @@
 config ARC_EMAC
 	tristate "ARC EMAC support"
 	select ARC_EMAC_CORE
-	depends on OF_IRQ && OF_NET
+	depends on OF_IRQ
 	depends on ARC || COMPILE_TEST
 	help
 	  On some legacy ARC (Synopsys) FPGA boards such as ARCAngel4/ML50x
@@ -36,7 +36,7 @@
 config EMAC_ROCKCHIP
 	tristate "Rockchip EMAC support"
 	select ARC_EMAC_CORE
-	depends on OF_IRQ && OF_NET && REGULATOR
+	depends on OF_IRQ && REGULATOR
 	depends on ARCH_ROCKCHIP || COMPILE_TEST
 	help
 	  Support for Rockchip RK3036/RK3066/RK3188 EMAC ethernet controllers.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/arc/emac_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/arc/emac_main.c
@@ -111,6 +111,7 @@
 {
 	struct arc_emac_priv *priv = netdev_priv(ndev);
 	struct net_device_stats *stats = &ndev->stats;
+	struct device *dev = ndev->dev.parent;
 	unsigned int i;
 
 	for (i = 0; i < TX_BD_NUM; i++) {
@@ -140,7 +141,7 @@
 			stats->tx_bytes += skb->len;
 		}
 
-		dma_unmap_single(&ndev->dev, dma_unmap_addr(tx_buff, addr),
+		dma_unmap_single(dev, dma_unmap_addr(tx_buff, addr),
 				 dma_unmap_len(tx_buff, len), DMA_TO_DEVICE);
 
 		/* return the sk_buff to system */
@@ -174,6 +175,7 @@
 static int arc_emac_rx(struct net_device *ndev, int budget)
 {
 	struct arc_emac_priv *priv = netdev_priv(ndev);
+	struct device *dev = ndev->dev.parent;
 	unsigned int work_done;
 
 	for (work_done = 0; work_done < budget; work_done++) {
@@ -223,9 +225,9 @@
 			continue;
 		}
 
-		addr = dma_map_single(&ndev->dev, (void *)skb->data,
+		addr = dma_map_single(dev, (void *)skb->data,
 				      EMAC_BUFFER_SIZE, DMA_FROM_DEVICE);
-		if (dma_mapping_error(&ndev->dev, addr)) {
+		if (dma_mapping_error(dev, addr)) {
 			if (net_ratelimit())
 				netdev_err(ndev, "cannot map dma buffer\n");
 			dev_kfree_skb(skb);
@@ -237,7 +239,7 @@
 		}
 
 		/* unmap previosly mapped skb */
-		dma_unmap_single(&ndev->dev, dma_unmap_addr(rx_buff, addr),
+		dma_unmap_single(dev, dma_unmap_addr(rx_buff, addr),
 				 dma_unmap_len(rx_buff, len), DMA_FROM_DEVICE);
 
 		pktlen = info & LEN_MASK;
@@ -423,6 +425,7 @@
 {
 	struct arc_emac_priv *priv = netdev_priv(ndev);
 	struct phy_device *phy_dev = ndev->phydev;
+	struct device *dev = ndev->dev.parent;
 	int i;
 
 	phy_dev->autoneg = AUTONEG_ENABLE;
@@ -445,9 +448,9 @@
 		if (unlikely(!rx_buff->skb))
 			return -ENOMEM;
 
-		addr = dma_map_single(&ndev->dev, (void *)rx_buff->skb->data,
+		addr = dma_map_single(dev, (void *)rx_buff->skb->data,
 				      EMAC_BUFFER_SIZE, DMA_FROM_DEVICE);
-		if (dma_mapping_error(&ndev->dev, addr)) {
+		if (dma_mapping_error(dev, addr)) {
 			netdev_err(ndev, "cannot dma map\n");
 			dev_kfree_skb(rx_buff->skb);
 			return -ENOMEM;
@@ -548,6 +551,7 @@
 static void arc_free_tx_queue(struct net_device *ndev)
 {
 	struct arc_emac_priv *priv = netdev_priv(ndev);
+	struct device *dev = ndev->dev.parent;
 	unsigned int i;
 
 	for (i = 0; i < TX_BD_NUM; i++) {
@@ -555,7 +559,7 @@
 		struct buffer_state *tx_buff = &priv->tx_buff[i];
 
 		if (tx_buff->skb) {
-			dma_unmap_single(&ndev->dev,
+			dma_unmap_single(dev,
 					 dma_unmap_addr(tx_buff, addr),
 					 dma_unmap_len(tx_buff, len),
 					 DMA_TO_DEVICE);
@@ -579,6 +583,7 @@
 static void arc_free_rx_queue(struct net_device *ndev)
 {
 	struct arc_emac_priv *priv = netdev_priv(ndev);
+	struct device *dev = ndev->dev.parent;
 	unsigned int i;
 
 	for (i = 0; i < RX_BD_NUM; i++) {
@@ -586,7 +591,7 @@
 		struct buffer_state *rx_buff = &priv->rx_buff[i];
 
 		if (rx_buff->skb) {
-			dma_unmap_single(&ndev->dev,
+			dma_unmap_single(dev,
 					 dma_unmap_addr(rx_buff, addr),
 					 dma_unmap_len(rx_buff, len),
 					 DMA_FROM_DEVICE);
@@ -679,6 +684,7 @@
 	unsigned int len, *txbd_curr = &priv->txbd_curr;
 	struct net_device_stats *stats = &ndev->stats;
 	__le32 *info = &priv->txbd[*txbd_curr].info;
+	struct device *dev = ndev->dev.parent;
 	dma_addr_t addr;
 
 	if (skb_padto(skb, ETH_ZLEN))
@@ -692,10 +698,9 @@
 		return NETDEV_TX_BUSY;
 	}
 
-	addr = dma_map_single(&ndev->dev, (void *)skb->data, len,
-			      DMA_TO_DEVICE);
+	addr = dma_map_single(dev, (void *)skb->data, len, DMA_TO_DEVICE);
 
-	if (unlikely(dma_mapping_error(&ndev->dev, addr))) {
+	if (unlikely(dma_mapping_error(dev, addr))) {
 		stats->tx_dropped++;
 		stats->tx_errors++;
 		dev_kfree_skb_any(skb);
@@ -941,7 +946,7 @@
 	}
 
 	/* Get MAC address from device tree */
-	err = of_get_mac_address(dev->of_node, ndev->dev_addr);
+	err = of_get_ethdev_address(dev->of_node, ndev);
 	if (err)
 		eth_hw_addr_random(ndev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/atheros/ag71xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/atheros/ag71xx.c
@@ -1480,7 +1480,7 @@
 	if (ret) {
 		netif_err(ag, link, ndev, "phylink_of_phy_connect filed with err: %i\n",
 			  ret);
-		goto err;
+		return ret;
 	}
 
 	max_frame_len = ag71xx_max_frame_len(ndev->mtu);
@@ -1501,6 +1501,7 @@
 
 err:
 	ag71xx_rings_cleanup(ag);
+	phylink_disconnect_phy(ag->phylink);
 	return ret;
 }
 
@@ -1915,15 +1916,12 @@
 	ag->mac_reset = devm_reset_control_get(&pdev->dev, "mac");
 	if (IS_ERR(ag->mac_reset)) {
 		netif_err(ag, probe, ndev, "missing mac reset\n");
-		err = PTR_ERR(ag->mac_reset);
-		goto err_free;
+		return PTR_ERR(ag->mac_reset);
 	}
 
 	ag->mac_base = devm_ioremap(&pdev->dev, res->start, resource_size(res));
-	if (!ag->mac_base) {
-		err = -ENOMEM;
-		goto err_free;
-	}
+	if (!ag->mac_base)
+		return -ENOMEM;
 
 	ndev->irq = platform_get_irq(pdev, 0);
 	err = devm_request_irq(&pdev->dev, ndev->irq, ag71xx_interrupt,
@@ -1931,7 +1929,7 @@
 	if (err) {
 		netif_err(ag, probe, ndev, "unable to request IRQ %d\n",
 			  ndev->irq);
-		goto err_free;
+		return err;
 	}
 
 	ndev->netdev_ops = &ag71xx_netdev_ops;
@@ -1959,16 +1957,14 @@
 	ag->stop_desc = dmam_alloc_coherent(&pdev->dev,
 					    sizeof(struct ag71xx_desc),
 					    &ag->stop_desc_dma, GFP_KERNEL);
-	if (!ag->stop_desc) {
-		err = -ENOMEM;
-		goto err_free;
-	}
+	if (!ag->stop_desc)
+		return -ENOMEM;
 
 	ag->stop_desc->data = 0;
 	ag->stop_desc->ctrl = 0;
 	ag->stop_desc->next = (u32)ag->stop_desc_dma;
 
-	err = of_get_mac_address(np, ndev->dev_addr);
+	err = of_get_ethdev_address(np, ndev);
 	if (err) {
 		netif_err(ag, probe, ndev, "invalid MAC address, using random address\n");
 		eth_random_addr(ndev->dev_addr);
@@ -1977,7 +1973,7 @@
 	err = of_get_phy_mode(np, &ag->phy_if_mode);
 	if (err) {
 		netif_err(ag, probe, ndev, "missing phy-mode property in DT\n");
-		goto err_free;
+		return err;
 	}
 
 	netif_napi_add(ndev, &ag->napi, ag71xx_poll, AG71XX_NAPI_WEIGHT);
@@ -1985,7 +1981,7 @@
 	err = clk_prepare_enable(ag->clk_eth);
 	if (err) {
 		netif_err(ag, probe, ndev, "Failed to enable eth clk.\n");
-		goto err_free;
+		return err;
 	}
 
 	ag71xx_wr(ag, AG71XX_REG_MAC_CFG1, 0);
@@ -2021,8 +2017,6 @@
 	ag71xx_mdio_remove(ag);
 err_put_clk:
 	clk_disable_unprepare(ag->clk_eth);
-err_free:
-	free_netdev(ndev);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/atheros/alx/ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/atheros/alx/ethtool.c
@@ -292,9 +292,8 @@
 	spin_lock(&alx->stats_lock);
 
 	alx_update_hw_stats(hw);
-	BUILD_BUG_ON(sizeof(hw->stats) - offsetof(struct alx_hw_stats, rx_ok) <
-		     ALX_NUM_STATS * sizeof(u64));
-	memcpy(data, &hw->stats.rx_ok, ALX_NUM_STATS * sizeof(u64));
+	BUILD_BUG_ON(sizeof(hw->stats) != ALX_NUM_STATS * sizeof(u64));
+	memcpy(data, &hw->stats, sizeof(hw->stats));
 
 	spin_unlock(&alx->stats_lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/atheros/alx/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/atheros/alx/main.c
@@ -1181,8 +1181,11 @@
 	alx->hw.mtu = mtu;
 	alx->rxbuf_size = max(max_frame, ALX_DEF_RXBUF_SIZE);
 	netdev_update_features(netdev);
-	if (netif_running(netdev))
+	if (netif_running(netdev)) {
+		mutex_lock(&alx->mtx);
 		alx_reinit(alx);
+		mutex_unlock(&alx->mtx);
+	}
 	return 0;
 }
 
@@ -1909,11 +1912,14 @@
 
 	if (!netif_running(alx->dev))
 		return 0;
+
+	rtnl_lock();
 	netif_device_detach(alx->dev);
 
 	mutex_lock(&alx->mtx);
 	__alx_stop(alx);
 	mutex_unlock(&alx->mtx);
+	rtnl_unlock();
 
 	return 0;
 }
@@ -1924,6 +1930,7 @@
 	struct alx_hw *hw = &alx->hw;
 	int err;
 
+	rtnl_lock();
 	mutex_lock(&alx->mtx);
 	alx_reset_phy(hw);
 
@@ -1940,6 +1947,7 @@
 
 unlock:
 	mutex_unlock(&alx->mtx);
+	rtnl_unlock();
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/atheros/atl1c/atl1c.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/atheros/atl1c/atl1c.h
@@ -504,15 +504,12 @@
 	u16 next_to_use;
 	u16 next_to_clean;
 	struct napi_struct napi;
-	struct page *rx_page;
-	unsigned int rx_page_offset;
 };
 
 /* board specific private data structure */
 struct atl1c_adapter {
 	struct net_device   *netdev;
 	struct pci_dev      *pdev;
-	unsigned int	    rx_frag_size;
 	struct atl1c_hw        hw;
 	struct atl1c_hw_stats  hw_stats;
 	struct mii_if_info  mii;    /* MII interface info */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
@@ -493,15 +493,10 @@
 static void atl1c_set_rxbufsize(struct atl1c_adapter *adapter,
 				struct net_device *dev)
 {
-	unsigned int head_size;
 	int mtu = dev->mtu;
 
 	adapter->rx_buffer_len = mtu > AT_RX_BUF_SIZE ?
 		roundup(mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN, 8) : AT_RX_BUF_SIZE;
-
-	head_size = SKB_DATA_ALIGN(adapter->rx_buffer_len + NET_SKB_PAD + NET_IP_ALIGN) +
-		    SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
-	adapter->rx_frag_size = roundup_pow_of_two(head_size);
 }
 
 static netdev_features_t atl1c_fix_features(struct net_device *netdev,
@@ -900,7 +895,7 @@
 		atl1c_clean_buffer(pdev, buffer_info);
 	}
 
-	netdev_reset_queue(adapter->netdev);
+	netdev_tx_reset_queue(netdev_get_tx_queue(adapter->netdev, queue));
 
 	/* Zero out Tx-buffers */
 	memset(tpd_ring->desc, 0, sizeof(struct atl1c_tpd_desc) *
@@ -974,7 +969,6 @@
 static void atl1c_free_ring_resources(struct atl1c_adapter *adapter)
 {
 	struct pci_dev *pdev = adapter->pdev;
-	int i;
 
 	dma_free_coherent(&pdev->dev, adapter->ring_header.size,
 			  adapter->ring_header.desc, adapter->ring_header.dma);
@@ -987,12 +981,6 @@
 		kfree(adapter->tpd_ring[0].buffer_info);
 		adapter->tpd_ring[0].buffer_info = NULL;
 	}
-	for (i = 0; i < adapter->rx_queue_count; ++i) {
-		if (adapter->rrd_ring[i].rx_page) {
-			put_page(adapter->rrd_ring[i].rx_page);
-			adapter->rrd_ring[i].rx_page = NULL;
-		}
-	}
 }
 
 /**
@@ -1764,48 +1752,11 @@
 	skb_checksum_none_assert(skb);
 }
 
-static struct sk_buff *atl1c_alloc_skb(struct atl1c_adapter *adapter,
-				       u32 queue, bool napi_mode)
-{
-	struct atl1c_rrd_ring *rrd_ring = &adapter->rrd_ring[queue];
-	struct sk_buff *skb;
-	struct page *page;
-
-	if (adapter->rx_frag_size > PAGE_SIZE) {
-		if (likely(napi_mode))
-			return napi_alloc_skb(&rrd_ring->napi,
-					      adapter->rx_buffer_len);
-		else
-			return netdev_alloc_skb_ip_align(adapter->netdev,
-							 adapter->rx_buffer_len);
-	}
-
-	page = rrd_ring->rx_page;
-	if (!page) {
-		page = alloc_page(GFP_ATOMIC);
-		if (unlikely(!page))
-			return NULL;
-		rrd_ring->rx_page = page;
-		rrd_ring->rx_page_offset = 0;
-	}
-
-	skb = build_skb(page_address(page) + rrd_ring->rx_page_offset,
-			adapter->rx_frag_size);
-	if (likely(skb)) {
-		skb_reserve(skb, NET_SKB_PAD + NET_IP_ALIGN);
-		rrd_ring->rx_page_offset += adapter->rx_frag_size;
-		if (rrd_ring->rx_page_offset >= PAGE_SIZE)
-			rrd_ring->rx_page = NULL;
-		else
-			get_page(page);
-	}
-	return skb;
-}
-
 static int atl1c_alloc_rx_buffer(struct atl1c_adapter *adapter, u32 queue,
 				 bool napi_mode)
 {
 	struct atl1c_rfd_ring *rfd_ring = &adapter->rfd_ring[queue];
+	struct atl1c_rrd_ring *rrd_ring = &adapter->rrd_ring[queue];
 	struct pci_dev *pdev = adapter->pdev;
 	struct atl1c_buffer *buffer_info, *next_info;
 	struct sk_buff *skb;
@@ -1824,13 +1775,27 @@
 	while (next_info->flags & ATL1C_BUFFER_FREE) {
 		rfd_desc = ATL1C_RFD_DESC(rfd_ring, rfd_next_to_use);
 
-		skb = atl1c_alloc_skb(adapter, queue, napi_mode);
+		/* When DMA RX address is set to something like
+		 * 0x....fc0, it will be very likely to cause DMA
+		 * RFD overflow issue.
+		 *
+		 * To work around it, we apply rx skb with 64 bytes
+		 * longer space, and offset the address whenever
+		 * 0x....fc0 is detected.
+		 */
+		if (likely(napi_mode))
+			skb = napi_alloc_skb(&rrd_ring->napi, adapter->rx_buffer_len + 64);
+		else
+			skb = netdev_alloc_skb(adapter->netdev, adapter->rx_buffer_len + 64);
 		if (unlikely(!skb)) {
 			if (netif_msg_rx_err(adapter))
 				dev_warn(&pdev->dev, "alloc rx buffer failed\n");
 			break;
 		}
 
+		if (((unsigned long)skb->data & 0xfff) == 0xfc0)
+			skb_reserve(skb, 64);
+
 		/*
 		 * Make buffer alignment 2 beyond a 16 byte boundary
 		 * this will result in a 16 byte aligned IP header after
@@ -2104,8 +2069,11 @@
 			real_len = (((unsigned char *)ip_hdr(skb) - skb->data)
 					+ ntohs(ip_hdr(skb)->tot_len));
 
-			if (real_len < skb->len)
-				pskb_trim(skb, real_len);
+			if (real_len < skb->len) {
+				err = pskb_trim(skb, real_len);
+				if (err)
+					return err;
+			}
 
 			hdr_len = (skb_transport_offset(skb) + tcp_hdrlen(skb));
 			if (unlikely(skb->len == hdr_len)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/atheros/atl1e/atl1e_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/atheros/atl1e/atl1e_main.c
@@ -866,10 +866,13 @@
 		netdev_err(adapter->netdev, "offset(%d) > ring size(%d) !!\n",
 			   offset, adapter->ring_size);
 		err = -1;
-		goto failed;
+		goto free_buffer;
 	}
 
 	return 0;
+free_buffer:
+	kfree(tx_ring->tx_buffer);
+	tx_ring->tx_buffer = NULL;
 failed:
 	if (adapter->ring_vir_addr != NULL) {
 		dma_free_coherent(&pdev->dev, adapter->ring_size,
@@ -1642,8 +1645,11 @@
 			real_len = (((unsigned char *)ip_hdr(skb) - skb->data)
 					+ ntohs(ip_hdr(skb)->tot_len));
 
-			if (real_len < skb->len)
-				pskb_trim(skb, real_len);
+			if (real_len < skb->len) {
+				err = pskb_trim(skb, real_len);
+				if (err)
+					return err;
+			}
 
 			hdr_len = (skb_transport_offset(skb) + tcp_hdrlen(skb));
 			if (unlikely(skb->len == hdr_len)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/Kconfig
@@ -71,6 +71,7 @@
 config BCMGENET
 	tristate "Broadcom GENET internal MAC support"
 	depends on HAS_IOMEM
+	depends on PTP_1588_CLOCK_OPTIONAL || !ARCH_BCM2835
 	select MII
 	select PHYLIB
 	select FIXED_PHY
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/Makefile
@@ -17,3 +17,8 @@
 obj-$(CONFIG_BGMAC_PLATFORM) += bgmac-platform.o
 obj-$(CONFIG_SYSTEMPORT) += bcmsysport.o
 obj-$(CONFIG_BNXT) += bnxt/
+
+# FIXME: temporarily silence -Warray-bounds on non W=1+ builds
+ifndef KBUILD_EXTRA_WARN
+CFLAGS_tg3.o += -Wno-array-bounds
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/b44.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/b44.c
@@ -218,7 +218,8 @@
 	data[1] = (val >> 0) & 0xFF;
 }
 
-static inline void __b44_cam_write(struct b44 *bp, unsigned char *data, int index)
+static inline void __b44_cam_write(struct b44 *bp,
+				   const unsigned char *data, int index)
 {
 	u32 val;
 
@@ -1507,7 +1508,8 @@
 	}
 }
 
-static int b44_magic_pattern(u8 *macaddr, u8 *ppattern, u8 *pmask, int offset)
+static int b44_magic_pattern(const u8 *macaddr, u8 *ppattern, u8 *pmask,
+			     int offset)
 {
 	int magicsync = 6;
 	int k, j, len = offset;
@@ -2027,12 +2029,14 @@
 		bp->flags |= B44_FLAG_TX_PAUSE;
 	else
 		bp->flags &= ~B44_FLAG_TX_PAUSE;
-	if (bp->flags & B44_FLAG_PAUSE_AUTO) {
-		b44_halt(bp);
-		b44_init_rings(bp);
-		b44_init_hw(bp, B44_FULL_RESET);
-	} else {
-		__b44_set_flow_ctrl(bp, bp->flags);
+	if (netif_running(dev)) {
+		if (bp->flags & B44_FLAG_PAUSE_AUTO) {
+			b44_halt(bp);
+			b44_init_rings(bp);
+			b44_init_hw(bp, B44_FULL_RESET);
+		} else {
+			__b44_set_flow_ctrl(bp, bp->flags);
+		}
 	}
 	spin_unlock_irq(&bp->lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bcm4908_enet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bcm4908_enet.c
@@ -561,8 +561,6 @@
 
 	if (++ring->write_idx == ring->length - 1)
 		ring->write_idx = 0;
-	enet->netdev->stats.tx_bytes += skb->len;
-	enet->netdev->stats.tx_packets++;
 
 	return NETDEV_TX_OK;
 }
@@ -646,13 +644,17 @@
 
 		dma_unmap_single(dev, slot->dma_addr, slot->len, DMA_TO_DEVICE);
 		dev_kfree_skb(slot->skb);
+
+		handled++;
 		bytes += slot->len;
+
 		if (++tx_ring->read_idx == tx_ring->length)
 			tx_ring->read_idx = 0;
-
-		handled++;
 	}
 
+	enet->netdev->stats.tx_packets += handled;
+	enet->netdev->stats.tx_bytes += bytes;
+
 	if (handled < weight) {
 		napi_complete_done(napi, handled);
 		bcm4908_enet_dma_ring_intrs_on(enet, tx_ring);
@@ -708,14 +710,16 @@
 
 	enet->irq_tx = platform_get_irq_byname(pdev, "tx");
 
-	dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	err = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	if (err)
+		return err;
 
 	err = bcm4908_enet_dma_alloc(enet);
 	if (err)
 		return err;
 
 	SET_NETDEV_DEV(netdev, &pdev->dev);
-	err = of_get_mac_address(dev->of_node, netdev->dev_addr);
+	err = of_get_ethdev_address(dev->of_node, netdev);
 	if (err)
 		eth_hw_addr_random(netdev);
 	netdev->netdev_ops = &bcm4908_enet_netdev_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bcmsysport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bcmsysport.c
@@ -1309,11 +1309,11 @@
 	struct bcm_sysport_priv *priv = netdev_priv(dev);
 	struct device *kdev = &priv->pdev->dev;
 	struct bcm_sysport_tx_ring *ring;
+	unsigned long flags, desc_flags;
 	struct bcm_sysport_cb *cb;
 	struct netdev_queue *txq;
 	u32 len_status, addr_lo;
 	unsigned int skb_len;
-	unsigned long flags;
 	dma_addr_t mapping;
 	u16 queue;
 	int ret;
@@ -1348,6 +1348,7 @@
 		netif_err(priv, tx_err, dev, "DMA map failed at %p (len=%d)\n",
 			  skb->data, skb_len);
 		ret = NETDEV_TX_OK;
+		dev_kfree_skb_any(skb);
 		goto out;
 	}
 
@@ -1373,8 +1374,10 @@
 	ring->desc_count--;
 
 	/* Ports are latched, so write upper address first */
+	spin_lock_irqsave(&priv->desc_lock, desc_flags);
 	tdma_writel(priv, len_status, TDMA_WRITE_PORT_HI(ring->index));
 	tdma_writel(priv, addr_lo, TDMA_WRITE_PORT_LO(ring->index));
+	spin_unlock_irqrestore(&priv->desc_lock, desc_flags);
 
 	/* Check ring space and update SW control flow */
 	if (ring->desc_count == 0)
@@ -1818,7 +1821,7 @@
 }
 
 static void umac_set_hw_addr(struct bcm_sysport_priv *priv,
-			     unsigned char *addr)
+			     const unsigned char *addr)
 {
 	u32 mac0 = (addr[0] << 24) | (addr[1] << 16) | (addr[2] << 8) |
 		    addr[3];
@@ -1953,7 +1956,11 @@
 	unsigned int i;
 	int ret;
 
-	clk_prepare_enable(priv->clk);
+	ret = clk_prepare_enable(priv->clk);
+	if (ret) {
+		netdev_err(dev, "could not enable priv clock\n");
+		return ret;
+	}
 
 	/* Reset UniMAC */
 	umac_reset(priv);
@@ -1989,6 +1996,9 @@
 		goto out_clk_disable;
 	}
 
+	/* Indicate that the MAC is responsible for PHY PM */
+	phydev->mac_managed_pm = true;
+
 	/* Reset house keeping link status */
 	priv->old_duplex = -1;
 	priv->old_link = -1;
@@ -2013,6 +2023,7 @@
 	}
 
 	/* Initialize both hardware and software ring */
+	spin_lock_init(&priv->desc_lock);
 	for (i = 0; i < dev->num_tx_queues; i++) {
 		ret = bcm_sysport_init_tx_ring(priv, i);
 		if (ret) {
@@ -2555,7 +2566,7 @@
 	}
 
 	/* Initialize netdevice members */
-	ret = of_get_mac_address(dn, dev->dev_addr);
+	ret = of_get_ethdev_address(dn, dev);
 	if (ret) {
 		dev_warn(&pdev->dev, "using random Ethernet MAC\n");
 		eth_hw_addr_random(dev);
@@ -2582,8 +2593,10 @@
 		device_set_wakeup_capable(&pdev->dev, 1);
 
 	priv->wol_clk = devm_clk_get_optional(&pdev->dev, "sw_sysportwol");
-	if (IS_ERR(priv->wol_clk))
-		return PTR_ERR(priv->wol_clk);
+	if (IS_ERR(priv->wol_clk)) {
+		ret = PTR_ERR(priv->wol_clk);
+		goto err_deregister_fixed_link;
+	}
 
 	/* Set the needed headroom once and for all */
 	BUILD_BUG_ON(sizeof(struct bcm_tsb) != 8);
@@ -2609,7 +2622,11 @@
 		goto err_deregister_notifier;
 	}
 
-	clk_prepare_enable(priv->clk);
+	ret = clk_prepare_enable(priv->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "could not enable priv clock\n");
+		goto err_deregister_netdev;
+	}
 
 	priv->rev = topctrl_readl(priv, REV_CNTL) & REV_MASK;
 	dev_info(&pdev->dev,
@@ -2623,6 +2640,8 @@
 
 	return 0;
 
+err_deregister_netdev:
+	unregister_netdev(dev);
 err_deregister_notifier:
 	unregister_netdevice_notifier(&priv->netdev_notifier);
 err_deregister_fixed_link:
@@ -2794,7 +2813,12 @@
 	if (!netif_running(dev))
 		return 0;
 
-	clk_prepare_enable(priv->clk);
+	ret = clk_prepare_enable(priv->clk);
+	if (ret) {
+		netdev_err(dev, "could not enable priv clock\n");
+		return ret;
+	}
+
 	if (priv->wolopts)
 		clk_disable_unprepare(priv->wol_clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bcmsysport.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bcmsysport.h
@@ -711,6 +711,7 @@
 	int			wol_irq;
 
 	/* Transmit rings */
+	spinlock_t		desc_lock;
 	struct bcm_sysport_tx_ring *tx_rings;
 
 	/* Receive queue */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bgmac-bcma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bgmac-bcma.c
@@ -128,7 +128,7 @@
 
 	bcma_set_drvdata(core, bgmac);
 
-	err = of_get_mac_address(bgmac->dev->of_node, bgmac->net_dev->dev_addr);
+	err = of_get_ethdev_address(bgmac->dev->of_node, bgmac->net_dev);
 	if (err == -EPROBE_DEFER)
 		return err;
 
@@ -150,7 +150,7 @@
 			err = -ENOTSUPP;
 			goto err;
 		}
-		ether_addr_copy(bgmac->net_dev->dev_addr, mac);
+		eth_hw_addr_set(bgmac->net_dev, mac);
 	}
 
 	/* On BCM4706 we need common core to access PHY */
@@ -228,12 +228,12 @@
 		bgmac->feature_flags |= BGMAC_FEAT_CLKCTLST;
 		bgmac->feature_flags |= BGMAC_FEAT_FLW_CTRL1;
 		bgmac->feature_flags |= BGMAC_FEAT_SW_TYPE_PHY;
-		if (ci->pkg == BCMA_PKG_ID_BCM47188 ||
-		    ci->pkg == BCMA_PKG_ID_BCM47186) {
+		if ((ci->id == BCMA_CHIP_ID_BCM5357 && ci->pkg == BCMA_PKG_ID_BCM47186) ||
+		    (ci->id == BCMA_CHIP_ID_BCM53572 && ci->pkg == BCMA_PKG_ID_BCM47188)) {
 			bgmac->feature_flags |= BGMAC_FEAT_SW_TYPE_RGMII;
 			bgmac->feature_flags |= BGMAC_FEAT_IOST_ATTACHED;
 		}
-		if (ci->pkg == BCMA_PKG_ID_BCM5358)
+		if (ci->id == BCMA_CHIP_ID_BCM5357 && ci->pkg == BCMA_PKG_ID_BCM5358)
 			bgmac->feature_flags |= BGMAC_FEAT_SW_TYPE_EPHYRMII;
 		break;
 	case BCMA_CHIP_ID_BCM53573:
@@ -323,7 +323,6 @@
 	bcma_mdio_mii_unregister(bgmac->mii_bus);
 	bgmac_enet_remove(bgmac);
 	bcma_set_drvdata(core, NULL);
-	kfree(bgmac);
 }
 
 static struct bcma_driver bgmac_bcma_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -171,7 +171,9 @@
 static int bgmac_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
+	struct device_node *phy_node;
 	struct bgmac *bgmac;
+	struct resource *regs;
 	int ret;
 
 	bgmac = bgmac_alloc(&pdev->dev);
@@ -191,7 +193,7 @@
 	bgmac->dev = &pdev->dev;
 	bgmac->dma_dev = &pdev->dev;
 
-	ret = of_get_mac_address(np, bgmac->net_dev->dev_addr);
+	ret = of_get_ethdev_address(np, bgmac->net_dev);
 	if (ret == -EPROBE_DEFER)
 		return ret;
 
@@ -208,15 +210,23 @@
 	if (IS_ERR(bgmac->plat.base))
 		return PTR_ERR(bgmac->plat.base);
 
-	bgmac->plat.idm_base = devm_platform_ioremap_resource_byname(pdev, "idm_base");
-	if (IS_ERR(bgmac->plat.idm_base))
-		return PTR_ERR(bgmac->plat.idm_base);
-	else
+	/* The idm_base resource is optional for some platforms */
+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "idm_base");
+	if (regs) {
+		bgmac->plat.idm_base = devm_ioremap_resource(&pdev->dev, regs);
+		if (IS_ERR(bgmac->plat.idm_base))
+			return PTR_ERR(bgmac->plat.idm_base);
 		bgmac->feature_flags &= ~BGMAC_FEAT_IDM_MASK;
+	}
 
-	bgmac->plat.nicpm_base = devm_platform_ioremap_resource_byname(pdev, "nicpm_base");
-	if (IS_ERR(bgmac->plat.nicpm_base))
-		return PTR_ERR(bgmac->plat.nicpm_base);
+	/* The nicpm_base resource is optional for some platforms */
+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
+	if (regs) {
+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
+							       regs);
+		if (IS_ERR(bgmac->plat.nicpm_base))
+			return PTR_ERR(bgmac->plat.nicpm_base);
+	}
 
 	bgmac->read = platform_bgmac_read;
 	bgmac->write = platform_bgmac_write;
@@ -227,7 +237,9 @@
 	bgmac->cco_ctl_maskset = platform_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = platform_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = platform_bgmac_cmn_maskset32;
-	if (of_parse_phandle(np, "phy-handle", 0)) {
+	phy_node = of_parse_phandle(np, "phy-handle", 0);
+	if (phy_node) {
+		of_node_put(phy_node);
 		bgmac->phy_connect = platform_phy_connect;
 	} else {
 		bgmac->phy_connect = bgmac_phy_connect_direct;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bgmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bgmac.c
@@ -189,8 +189,8 @@
 	}
 
 	slot->skb = skb;
-	ring->end += nr_frags + 1;
 	netdev_sent_queue(net_dev, skb->len);
+	ring->end += nr_frags + 1;
 
 	wmb();
 
@@ -768,7 +768,7 @@
 	udelay(2);
 }
 
-static void bgmac_write_mac_address(struct bgmac *bgmac, u8 *addr)
+static void bgmac_write_mac_address(struct bgmac *bgmac, const u8 *addr)
 {
 	u32 tmp;
 
@@ -890,13 +890,13 @@
 
 		if (iost & BGMAC_BCMA_IOST_ATTACHED) {
 			flags = BGMAC_BCMA_IOCTL_SW_CLKEN;
-			if (!bgmac->has_robosw)
+			if (bgmac->in_init || !bgmac->has_robosw)
 				flags |= BGMAC_BCMA_IOCTL_SW_RESET;
 		}
 		bgmac_clk_enable(bgmac, flags);
 	}
 
-	if (iost & BGMAC_BCMA_IOST_ATTACHED && !bgmac->has_robosw)
+	if (iost & BGMAC_BCMA_IOST_ATTACHED && (bgmac->in_init || !bgmac->has_robosw))
 		bgmac_idm_write(bgmac, BCMA_IOCTL,
 				bgmac_idm_read(bgmac, BCMA_IOCTL) &
 				~BGMAC_BCMA_IOCTL_SW_RESET);
@@ -1241,7 +1241,7 @@
 	if (ret < 0)
 		return ret;
 
-	ether_addr_copy(net_dev->dev_addr, sa->sa_data);
+	eth_hw_addr_set(net_dev, sa->sa_data);
 	bgmac_write_mac_address(bgmac, net_dev->dev_addr);
 
 	eth_commit_mac_addr_change(net_dev, addr);
@@ -1448,7 +1448,7 @@
 	int err;
 
 	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, NULL);
-	if (!phy_dev || IS_ERR(phy_dev)) {
+	if (IS_ERR(phy_dev)) {
 		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
 		return -ENODEV;
 	}
@@ -1490,7 +1490,7 @@
 	struct net_device *net_dev = bgmac->net_dev;
 	int err;
 
-	bgmac_chip_intrs_off(bgmac);
+	bgmac->in_init = true;
 
 	net_dev->irq = bgmac->irq;
 	SET_NETDEV_DEV(net_dev, bgmac->dev);
@@ -1509,6 +1509,8 @@
 	 */
 	bgmac_clk_enable(bgmac, 0);
 
+	bgmac_chip_intrs_off(bgmac);
+
 	/* This seems to be fixing IRQ by assigning OOB #6 to the core */
 	if (!(bgmac->feature_flags & BGMAC_FEAT_IDM_MASK)) {
 		if (bgmac->feature_flags & BGMAC_FEAT_IRQ_ID_OOB_6)
@@ -1542,6 +1544,8 @@
 	/* Omit FCS from max MTU size */
 	net_dev->max_mtu = BGMAC_RX_MAX_FRAME_SIZE - ETH_FCS_LEN;
 
+	bgmac->in_init = false;
+
 	err = register_netdev(bgmac->net_dev);
 	if (err) {
 		dev_err(bgmac->dev, "Cannot register net device\n");
@@ -1568,7 +1572,6 @@
 	phy_disconnect(bgmac->net_dev->phydev);
 	netif_napi_del(&bgmac->napi);
 	bgmac_dma_free(bgmac);
-	free_netdev(bgmac->net_dev);
 }
 EXPORT_SYMBOL_GPL(bgmac_enet_remove);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bgmac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bgmac.h
@@ -328,8 +328,7 @@
 #define BGMAC_RX_FRAME_OFFSET			30		/* There are 2 unused bytes between header and real data */
 #define BGMAC_RX_BUF_OFFSET			(NET_SKB_PAD + NET_IP_ALIGN - \
 						 BGMAC_RX_FRAME_OFFSET)
-/* Jumbo frame size with FCS */
-#define BGMAC_RX_MAX_FRAME_SIZE			9724
+#define BGMAC_RX_MAX_FRAME_SIZE			1536
 #define BGMAC_RX_BUF_SIZE			(BGMAC_RX_FRAME_OFFSET + BGMAC_RX_MAX_FRAME_SIZE)
 #define BGMAC_RX_ALLOC_SIZE			(SKB_DATA_ALIGN(BGMAC_RX_BUF_SIZE + BGMAC_RX_BUF_OFFSET) + \
 						 SKB_DATA_ALIGN(sizeof(struct skb_shared_info)))
@@ -474,6 +473,8 @@
 	int irq;
 	u32 int_mask;
 
+	bool in_init;
+
 	/* Current MAC state */
 	int mac_speed;
 	int mac_duplex;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2.c
@@ -2704,7 +2704,7 @@
 }
 
 static void
-bnx2_set_mac_addr(struct bnx2 *bp, u8 *mac_addr, u32 pos)
+bnx2_set_mac_addr(struct bnx2 *bp, const u8 *mac_addr, u32 pos)
 {
 	u32 val;
 
@@ -8212,7 +8212,7 @@
 		rc = dma_set_coherent_mask(&pdev->dev, persist_dma_mask);
 		if (rc) {
 			dev_err(&pdev->dev,
-				"pci_set_consistent_dma_mask failed, aborting\n");
+				"dma_set_coherent_mask failed, aborting\n");
 			goto err_out_unmap;
 		}
 	} else if ((rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) != 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1262,7 +1262,7 @@
 
 struct bnx2x_fw_stats_req {
 	struct stats_query_header hdr;
-	struct stats_query_entry query[FP_SB_MAX_E1x+
+	struct stats_query_entry query[FP_SB_MAX_E2 +
 		BNX2X_FIRST_QUEUE_QUERY_IDX];
 };
 
@@ -1850,6 +1850,14 @@
 
 	/* Vxlan/Geneve related information */
 	u16 udp_tunnel_ports[BNX2X_UDP_PORT_MAX];
+
+#define FW_CAP_INVALIDATE_VF_FP_HSI	BIT(0)
+	u32 fw_cap;
+
+	u32 fw_major;
+	u32 fw_minor;
+	u32 fw_rev;
+	u32 fw_eng;
 };
 
 /* Tx queues may be less or equal to Rx queues */
@@ -1994,7 +2002,7 @@
  * operation has been successfully scheduled and a negative - if a requested
  * operations has failed.
  */
-int bnx2x_set_mac_one(struct bnx2x *bp, u8 *mac,
+int bnx2x_set_mac_one(struct bnx2x *bp, const u8 *mac,
 		      struct bnx2x_vlan_mac_obj *obj, bool set,
 		      int mac_type, unsigned long *ramrod_flags);
 
@@ -2525,5 +2533,4 @@
  * Meant for implicit re-load flows.
  */
 int bnx2x_vlan_reconfigure_vid(struct bnx2x *bp);
-
 #endif /* bnx2x.h */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -788,6 +788,7 @@
 			BNX2X_ERR("skb_put is about to fail...  pad %d  len %d  rx_buf_size %d\n",
 				  pad, len, fp->rx_buf_size);
 			bnx2x_panic();
+			bnx2x_frag_free(fp, new_data);
 			return;
 		}
 #endif
@@ -1923,8 +1924,7 @@
 
 		/* Skip VLAN tag if present */
 		if (ether_type == ETH_P_8021Q) {
-			struct vlan_ethhdr *vhdr =
-				(struct vlan_ethhdr *)skb->data;
+			struct vlan_ethhdr *vhdr = skb_vlan_eth_hdr(skb);
 
 			ether_type = ntohs(vhdr->h_vlan_encapsulated_proto);
 		}
@@ -2363,26 +2363,30 @@
 	/* is another pf loaded on this engine? */
 	if (load_code != FW_MSG_CODE_DRV_LOAD_COMMON_CHIP &&
 	    load_code != FW_MSG_CODE_DRV_LOAD_COMMON) {
-		/* build my FW version dword */
-		u32 my_fw = (BCM_5710_FW_MAJOR_VERSION) +
-			(BCM_5710_FW_MINOR_VERSION << 8) +
-			(BCM_5710_FW_REVISION_VERSION << 16) +
-			(BCM_5710_FW_ENGINEERING_VERSION << 24);
+		u8 loaded_fw_major, loaded_fw_minor, loaded_fw_rev, loaded_fw_eng;
+		u32 loaded_fw;
 
 		/* read loaded FW from chip */
-		u32 loaded_fw = REG_RD(bp, XSEM_REG_PRAM);
+		loaded_fw = REG_RD(bp, XSEM_REG_PRAM);
 
-		DP(BNX2X_MSG_SP, "loaded fw %x, my fw %x\n",
-		   loaded_fw, my_fw);
+		loaded_fw_major = loaded_fw & 0xff;
+		loaded_fw_minor = (loaded_fw >> 8) & 0xff;
+		loaded_fw_rev = (loaded_fw >> 16) & 0xff;
+		loaded_fw_eng = (loaded_fw >> 24) & 0xff;
+
+		DP(BNX2X_MSG_SP, "loaded fw 0x%x major 0x%x minor 0x%x rev 0x%x eng 0x%x\n",
+		   loaded_fw, loaded_fw_major, loaded_fw_minor, loaded_fw_rev, loaded_fw_eng);
 
 		/* abort nic load if version mismatch */
-		if (my_fw != loaded_fw) {
+		if (loaded_fw_major != BCM_5710_FW_MAJOR_VERSION ||
+		    loaded_fw_minor != BCM_5710_FW_MINOR_VERSION ||
+		    loaded_fw_eng != BCM_5710_FW_ENGINEERING_VERSION ||
+		    loaded_fw_rev < BCM_5710_FW_REVISION_VERSION_V15) {
 			if (print_err)
-				BNX2X_ERR("bnx2x with FW %x was already loaded which mismatches my %x FW. Aborting\n",
-					  loaded_fw, my_fw);
+				BNX2X_ERR("loaded FW incompatible. Aborting\n");
 			else
-				BNX2X_DEV_INFO("bnx2x with FW %x was already loaded which mismatches my %x FW, possibly due to MF UNDI\n",
-					       loaded_fw, my_fw);
+				BNX2X_DEV_INFO("loaded FW incompatible, possibly due to MF UNDI\n");
+
 			return -EBUSY;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
@@ -1002,9 +1002,6 @@
 static inline void bnx2x_free_rx_mem_pool(struct bnx2x *bp,
 					  struct bnx2x_alloc_pool *pool)
 {
-	if (!pool->page)
-		return;
-
 	put_page(pool->page);
 
 	pool->page = NULL;
@@ -1015,6 +1012,9 @@
 {
 	int i;
 
+	if (!fp->page_pool.page)
+		return;
+
 	if (fp->mode == TPA_MODE_DISABLED)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
@@ -241,6 +241,8 @@
 	IRO[221].m2))
 #define XSTORM_VF_TO_PF_OFFSET(funcId) \
 	(IRO[48].base + ((funcId) * IRO[48].m1))
+#define XSTORM_ETH_FUNCTION_INFO_FP_HSI_VALID_E2_OFFSET(fid)	\
+	(IRO[386].base + ((fid) * IRO[386].m1))
 #define COMMON_ASM_INVALID_ASSERT_OPCODE 0x0
 
 /* eth hsi version */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
@@ -3024,7 +3024,8 @@
 
 #define BCM_5710_FW_MAJOR_VERSION			7
 #define BCM_5710_FW_MINOR_VERSION			13
-#define BCM_5710_FW_REVISION_VERSION		15
+#define BCM_5710_FW_REVISION_VERSION		21
+#define BCM_5710_FW_REVISION_VERSION_V15	15
 #define BCM_5710_FW_ENGINEERING_VERSION		0
 #define BCM_5710_FW_COMPILE_FLAGS			1
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_init_ops.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_init_ops.h
@@ -635,11 +635,13 @@
 {
 	int i, rc;
 	struct bnx2x_ilt *ilt = BP_ILT(bp);
-	struct ilt_client_info *ilt_cli = &ilt->clients[cli_num];
+	struct ilt_client_info *ilt_cli;
 
 	if (!ilt || !ilt->lines)
 		return -1;
 
+	ilt_cli = &ilt->clients[cli_num];
+
 	if (ilt_cli->flags & (ILT_CLIENT_SKIP_INIT | ILT_CLIENT_SKIP_MEM))
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -74,9 +74,19 @@
 	__stringify(BCM_5710_FW_MINOR_VERSION) "."	\
 	__stringify(BCM_5710_FW_REVISION_VERSION) "."	\
 	__stringify(BCM_5710_FW_ENGINEERING_VERSION)
+
+#define FW_FILE_VERSION_V15				\
+	__stringify(BCM_5710_FW_MAJOR_VERSION) "."      \
+	__stringify(BCM_5710_FW_MINOR_VERSION) "."	\
+	__stringify(BCM_5710_FW_REVISION_VERSION_V15) "."	\
+	__stringify(BCM_5710_FW_ENGINEERING_VERSION)
+
 #define FW_FILE_NAME_E1		"bnx2x/bnx2x-e1-" FW_FILE_VERSION ".fw"
 #define FW_FILE_NAME_E1H	"bnx2x/bnx2x-e1h-" FW_FILE_VERSION ".fw"
 #define FW_FILE_NAME_E2		"bnx2x/bnx2x-e2-" FW_FILE_VERSION ".fw"
+#define FW_FILE_NAME_E1_V15	"bnx2x/bnx2x-e1-" FW_FILE_VERSION_V15 ".fw"
+#define FW_FILE_NAME_E1H_V15	"bnx2x/bnx2x-e1h-" FW_FILE_VERSION_V15 ".fw"
+#define FW_FILE_NAME_E2_V15	"bnx2x/bnx2x-e2-" FW_FILE_VERSION_V15 ".fw"
 
 /* Time in jiffies before concluding the transmitter is hung */
 #define TX_TIMEOUT		(5*HZ)
@@ -90,6 +100,9 @@
 MODULE_FIRMWARE(FW_FILE_NAME_E1);
 MODULE_FIRMWARE(FW_FILE_NAME_E1H);
 MODULE_FIRMWARE(FW_FILE_NAME_E2);
+MODULE_FIRMWARE(FW_FILE_NAME_E1_V15);
+MODULE_FIRMWARE(FW_FILE_NAME_E1H_V15);
+MODULE_FIRMWARE(FW_FILE_NAME_E2_V15);
 
 int bnx2x_num_queues;
 module_param_named(num_queues, bnx2x_num_queues, int, 0444);
@@ -747,9 +760,7 @@
 		  CHIP_IS_E1(bp) ? "everest1" :
 		  CHIP_IS_E1H(bp) ? "everest1h" :
 		  CHIP_IS_E2(bp) ? "everest2" : "everest3",
-		  BCM_5710_FW_MAJOR_VERSION,
-		  BCM_5710_FW_MINOR_VERSION,
-		  BCM_5710_FW_REVISION_VERSION);
+		  bp->fw_major, bp->fw_minor, bp->fw_rev);
 
 	return rc;
 }
@@ -8417,7 +8428,7 @@
  * Init service functions
  */
 
-int bnx2x_set_mac_one(struct bnx2x *bp, u8 *mac,
+int bnx2x_set_mac_one(struct bnx2x *bp, const u8 *mac,
 		      struct bnx2x_vlan_mac_obj *obj, bool set,
 		      int mac_type, unsigned long *ramrod_flags)
 {
@@ -9146,7 +9157,7 @@
 
 	else if (bp->wol) {
 		u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
-		u8 *mac_addr = bp->dev->dev_addr;
+		const u8 *mac_addr = bp->dev->dev_addr;
 		struct pci_dev *pdev = bp->pdev;
 		u32 val;
 		u16 pmc;
@@ -13311,16 +13322,11 @@
 	/* Check FW version */
 	offset = be32_to_cpu(fw_hdr->fw_version.offset);
 	fw_ver = firmware->data + offset;
-	if ((fw_ver[0] != BCM_5710_FW_MAJOR_VERSION) ||
-	    (fw_ver[1] != BCM_5710_FW_MINOR_VERSION) ||
-	    (fw_ver[2] != BCM_5710_FW_REVISION_VERSION) ||
-	    (fw_ver[3] != BCM_5710_FW_ENGINEERING_VERSION)) {
+	if (fw_ver[0] != bp->fw_major || fw_ver[1] != bp->fw_minor ||
+	    fw_ver[2] != bp->fw_rev || fw_ver[3] != bp->fw_eng) {
 		BNX2X_ERR("Bad FW version:%d.%d.%d.%d. Should be %d.%d.%d.%d\n",
-		       fw_ver[0], fw_ver[1], fw_ver[2], fw_ver[3],
-		       BCM_5710_FW_MAJOR_VERSION,
-		       BCM_5710_FW_MINOR_VERSION,
-		       BCM_5710_FW_REVISION_VERSION,
-		       BCM_5710_FW_ENGINEERING_VERSION);
+			  fw_ver[0], fw_ver[1], fw_ver[2], fw_ver[3],
+			  bp->fw_major, bp->fw_minor, bp->fw_rev, bp->fw_eng);
 		return -EINVAL;
 	}
 
@@ -13400,32 +13406,49 @@
 
 static int bnx2x_init_firmware(struct bnx2x *bp)
 {
-	const char *fw_file_name;
+	const char *fw_file_name, *fw_file_name_v15;
 	struct bnx2x_fw_file_hdr *fw_hdr;
 	int rc;
 
 	if (bp->firmware)
 		return 0;
 
-	if (CHIP_IS_E1(bp))
+	if (CHIP_IS_E1(bp)) {
 		fw_file_name = FW_FILE_NAME_E1;
-	else if (CHIP_IS_E1H(bp))
+		fw_file_name_v15 = FW_FILE_NAME_E1_V15;
+	} else if (CHIP_IS_E1H(bp)) {
 		fw_file_name = FW_FILE_NAME_E1H;
-	else if (!CHIP_IS_E1x(bp))
+		fw_file_name_v15 = FW_FILE_NAME_E1H_V15;
+	} else if (!CHIP_IS_E1x(bp)) {
 		fw_file_name = FW_FILE_NAME_E2;
-	else {
+		fw_file_name_v15 = FW_FILE_NAME_E2_V15;
+	} else {
 		BNX2X_ERR("Unsupported chip revision\n");
 		return -EINVAL;
 	}
+
 	BNX2X_DEV_INFO("Loading %s\n", fw_file_name);
 
 	rc = request_firmware(&bp->firmware, fw_file_name, &bp->pdev->dev);
 	if (rc) {
-		BNX2X_ERR("Can't load firmware file %s\n",
-			  fw_file_name);
-		goto request_firmware_exit;
+		BNX2X_DEV_INFO("Trying to load older fw %s\n", fw_file_name_v15);
+
+		/* try to load prev version */
+		rc = request_firmware(&bp->firmware, fw_file_name_v15, &bp->pdev->dev);
+
+		if (rc)
+			goto request_firmware_exit;
+
+		bp->fw_rev = BCM_5710_FW_REVISION_VERSION_V15;
+	} else {
+		bp->fw_cap |= FW_CAP_INVALIDATE_VF_FP_HSI;
+		bp->fw_rev = BCM_5710_FW_REVISION_VERSION;
 	}
 
+	bp->fw_major = BCM_5710_FW_MAJOR_VERSION;
+	bp->fw_minor = BCM_5710_FW_MINOR_VERSION;
+	bp->fw_eng = BCM_5710_FW_ENGINEERING_VERSION;
+
 	rc = bnx2x_check_firmware(bp);
 	if (rc) {
 		BNX2X_ERR("Corrupt firmware file %s\n", fw_file_name);
@@ -14135,10 +14158,6 @@
 
 	/* Stop Tx */
 	bnx2x_tx_disable(bp);
-	/* Delete all NAPI objects */
-	bnx2x_del_all_napi(bp);
-	if (CNIC_LOADED(bp))
-		bnx2x_del_all_napi_cnic(bp);
 	netdev_reset_tc(bp->dev);
 
 	del_timer_sync(&bp->timer);
@@ -14243,6 +14262,11 @@
 		bnx2x_drain_tx_queues(bp);
 		bnx2x_send_unload_req(bp, UNLOAD_RECOVERY);
 		bnx2x_netif_stop(bp, 1);
+		bnx2x_del_all_napi(bp);
+
+		if (CNIC_LOADED(bp))
+			bnx2x_del_all_napi_cnic(bp);
+
 		bnx2x_free_irq(bp);
 
 		/* Report UNLOAD_DONE to MCP */
@@ -14293,11 +14317,16 @@
 	bp->fw_seq = SHMEM_RD(bp, func_mb[BP_FW_MB_IDX(bp)].drv_mb_header) &
 							DRV_MSG_SEQ_NUMBER_MASK;
 
-	if (netif_running(dev))
-		bnx2x_nic_load(bp, LOAD_NORMAL);
+	if (netif_running(dev)) {
+		if (bnx2x_nic_load(bp, LOAD_NORMAL)) {
+			netdev_err(bp->dev, "Error during driver initialization, try unloading/reloading the driver\n");
+			goto done;
+		}
+	}
 
 	netif_device_attach(dev);
 
+done:
 	rtnl_unlock();
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
@@ -758,9 +758,18 @@
 
 void bnx2x_vf_enable_access(struct bnx2x *bp, u8 abs_vfid)
 {
+	u16 abs_fid;
+
+	abs_fid = FW_VF_HANDLE(abs_vfid);
+
 	/* set the VF-PF association in the FW */
-	storm_memset_vf_to_pf(bp, FW_VF_HANDLE(abs_vfid), BP_FUNC(bp));
-	storm_memset_func_en(bp, FW_VF_HANDLE(abs_vfid), 1);
+	storm_memset_vf_to_pf(bp, abs_fid, BP_FUNC(bp));
+	storm_memset_func_en(bp, abs_fid, 1);
+
+	/* Invalidate fp_hsi version for vfs */
+	if (bp->fw_cap & FW_CAP_INVALIDATE_VF_FP_HSI)
+		REG_WR8(bp, BAR_XSTRORM_INTMEM +
+			    XSTORM_ETH_FUNCTION_INFO_FP_HSI_VALID_E2_OFFSET(abs_fid), 0);
 
 	/* clear vf errors*/
 	bnx2x_vf_semi_clear_err(bp, abs_vfid);
@@ -786,16 +795,20 @@
 
 static u8 bnx2x_vf_is_pcie_pending(struct bnx2x *bp, u8 abs_vfid)
 {
-	struct pci_dev *dev;
 	struct bnx2x_virtf *vf = bnx2x_vf_by_abs_fid(bp, abs_vfid);
+	struct pci_dev *dev;
+	bool pending;
 
 	if (!vf)
 		return false;
 
 	dev = pci_get_domain_bus_and_slot(vf->domain, vf->bus, vf->devfn);
-	if (dev)
-		return bnx2x_is_pcie_pending(dev);
-	return false;
+	if (!dev)
+		return false;
+	pending = bnx2x_is_pcie_pending(dev);
+	pci_dev_put(dev);
+
+	return pending;
 }
 
 int bnx2x_vf_flr_clnup_epilog(struct bnx2x *bp, u8 abs_vfid)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h
@@ -508,7 +508,8 @@
 void bnx2x_vfpf_close_vf(struct bnx2x *bp);
 int bnx2x_vfpf_setup_q(struct bnx2x *bp, struct bnx2x_fastpath *fp,
 		       bool is_leading);
-int bnx2x_vfpf_config_mac(struct bnx2x *bp, u8 *addr, u8 vf_qid, bool set);
+int bnx2x_vfpf_config_mac(struct bnx2x *bp, const u8 *addr, u8 vf_qid,
+			  bool set);
 int bnx2x_vfpf_config_rss(struct bnx2x *bp,
 			  struct bnx2x_config_rss_params *params);
 int bnx2x_vfpf_set_mcast(struct net_device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
@@ -722,7 +722,7 @@
 }
 
 /* request pf to add a mac for the vf */
-int bnx2x_vfpf_config_mac(struct bnx2x *bp, u8 *addr, u8 vf_qid, bool set)
+int bnx2x_vfpf_config_mac(struct bnx2x *bp, const u8 *addr, u8 vf_qid, bool set)
 {
 	struct vfpf_set_q_filters_tlv *req = &bp->vf2pf_mbox->req.set_q_filters;
 	struct pfvf_general_resp_tlv *resp = &bp->vf2pf_mbox->resp.general_resp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/Makefile
@@ -1,6 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_BNXT) += bnxt_en.o
 
-bnxt_en-y := bnxt.o bnxt_hwrm.o bnxt_sriov.o bnxt_ethtool.o bnxt_dcb.o bnxt_ulp.o bnxt_xdp.o bnxt_ptp.o bnxt_vfr.o bnxt_devlink.o bnxt_dim.o
+bnxt_en-y := bnxt.o bnxt_hwrm.o bnxt_sriov.o bnxt_ethtool.o bnxt_dcb.o bnxt_ulp.o bnxt_xdp.o bnxt_ptp.o bnxt_vfr.o bnxt_devlink.o bnxt_dim.o bnxt_coredump.o
 bnxt_en-$(CONFIG_BNXT_FLOWER_OFFLOAD) += bnxt_tc.o
 bnxt_en-$(CONFIG_DEBUG_FS) += bnxt_debugfs.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -223,12 +223,12 @@
 	{ PCI_VDEVICE(BROADCOM, 0x1750), .driver_data = BCM57508 },
 	{ PCI_VDEVICE(BROADCOM, 0x1751), .driver_data = BCM57504 },
 	{ PCI_VDEVICE(BROADCOM, 0x1752), .driver_data = BCM57502 },
-	{ PCI_VDEVICE(BROADCOM, 0x1800), .driver_data = BCM57508_NPAR },
+	{ PCI_VDEVICE(BROADCOM, 0x1800), .driver_data = BCM57502_NPAR },
 	{ PCI_VDEVICE(BROADCOM, 0x1801), .driver_data = BCM57504_NPAR },
-	{ PCI_VDEVICE(BROADCOM, 0x1802), .driver_data = BCM57502_NPAR },
-	{ PCI_VDEVICE(BROADCOM, 0x1803), .driver_data = BCM57508_NPAR },
+	{ PCI_VDEVICE(BROADCOM, 0x1802), .driver_data = BCM57508_NPAR },
+	{ PCI_VDEVICE(BROADCOM, 0x1803), .driver_data = BCM57502_NPAR },
 	{ PCI_VDEVICE(BROADCOM, 0x1804), .driver_data = BCM57504_NPAR },
-	{ PCI_VDEVICE(BROADCOM, 0x1805), .driver_data = BCM57502_NPAR },
+	{ PCI_VDEVICE(BROADCOM, 0x1805), .driver_data = BCM57508_NPAR },
 	{ PCI_VDEVICE(BROADCOM, 0xd802), .driver_data = BCM58802 },
 	{ PCI_VDEVICE(BROADCOM, 0xd804), .driver_data = BCM58804 },
 #ifdef CONFIG_BNXT_SRIOV
@@ -667,9 +667,6 @@
 	return NETDEV_TX_OK;
 
 tx_dma_error:
-	if (BNXT_TX_PTP_IS_SET(lflags))
-		atomic_inc(&bp->ptp_cfg->tx_avail);
-
 	last_frag = i;
 
 	/* start back at beginning and unmap skb */
@@ -691,6 +688,8 @@
 tx_free:
 	dev_kfree_skb_any(skb);
 tx_kick_pending:
+	if (BNXT_TX_PTP_IS_SET(lflags))
+		atomic_inc(&bp->ptp_cfg->tx_avail);
 	if (txr->kick_pending)
 		bnxt_txr_db_kick(bp, txr, txr->tx_prod);
 	txr->tx_buf_ring[txr->tx_prod].skb = NULL;
@@ -709,7 +708,6 @@
 
 	for (i = 0; i < nr_pkts; i++) {
 		struct bnxt_sw_tx_bd *tx_buf;
-		bool compl_deferred = false;
 		struct sk_buff *skb;
 		int j, last;
 
@@ -718,6 +716,8 @@
 		skb = tx_buf->skb;
 		tx_buf->skb = NULL;
 
+		tx_bytes += skb->len;
+
 		if (tx_buf->is_push) {
 			tx_buf->is_push = 0;
 			goto next_tx_int;
@@ -738,8 +738,9 @@
 		}
 		if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS)) {
 			if (bp->flags & BNXT_FLAG_CHIP_P5) {
+				/* PTP worker takes ownership of the skb */
 				if (!bnxt_get_tx_ts_p5(bp, skb))
-					compl_deferred = true;
+					skb = NULL;
 				else
 					atomic_inc(&bp->ptp_cfg->tx_avail);
 			}
@@ -748,9 +749,7 @@
 next_tx_int:
 		cons = NEXT_TX(cons);
 
-		tx_bytes += skb->len;
-		if (!compl_deferred)
-			dev_kfree_skb_any(skb);
+		dev_kfree_skb_any(skb);
 	}
 
 	netdev_tx_completed_queue(txq, nr_pkts, tx_bytes);
@@ -2520,6 +2519,7 @@
 	struct rx_cmp_ext *rxcmp1;
 	u32 cp_cons, tmp_raw_cons;
 	u32 raw_cons = cpr->cp_raw_cons;
+	bool flush_xdp = false;
 	u32 rx_pkts = 0;
 	u8 event = 0;
 
@@ -2554,6 +2554,8 @@
 				rx_pkts++;
 			else if (rc == -EBUSY)	/* partial completion */
 				break;
+			if (event & BNXT_REDIRECT_EVENT)
+				flush_xdp = true;
 		} else if (unlikely(TX_CMP_TYPE(txcmp) ==
 				    CMPL_BASE_TYPE_HWRM_DONE)) {
 			bnxt_hwrm_handler(bp, txcmp);
@@ -2573,6 +2575,8 @@
 
 	if (event & BNXT_AGG_EVENT)
 		bnxt_db_write(bp, &rxr->rx_agg_db, rxr->rx_agg_prod);
+	if (flush_xdp)
+		xdp_do_flush();
 
 	if (!bnxt_has_work(bp, cpr) && rx_pkts < budget) {
 		napi_complete_done(napi, rx_pkts);
@@ -2699,6 +2703,10 @@
 			u32 idx = le32_to_cpu(nqcmp->cq_handle_low);
 			struct bnxt_cp_ring_info *cpr2;
 
+			/* No more budget for RX work */
+			if (budget && work_done >= budget && idx == BNXT_RX_HDL)
+				break;
+
 			cpr2 = cpr->cp_ring_arr[idx];
 			work_done += __bnxt_poll_work(bp, cpr2,
 						      budget - work_done);
@@ -2995,7 +3003,7 @@
 
 static void bnxt_free_tpa_info(struct bnxt *bp)
 {
-	int i;
+	int i, j;
 
 	for (i = 0; i < bp->rx_nr_rings; i++) {
 		struct bnxt_rx_ring_info *rxr = &bp->rx_ring[i];
@@ -3003,8 +3011,10 @@
 		kfree(rxr->rx_tpa_idx_map);
 		rxr->rx_tpa_idx_map = NULL;
 		if (rxr->rx_tpa) {
-			kfree(rxr->rx_tpa[0].agg_arr);
-			rxr->rx_tpa[0].agg_arr = NULL;
+			for (j = 0; j < bp->max_tpa; j++) {
+				kfree(rxr->rx_tpa[j].agg_arr);
+				rxr->rx_tpa[j].agg_arr = NULL;
+			}
 		}
 		kfree(rxr->rx_tpa);
 		rxr->rx_tpa = NULL;
@@ -3013,14 +3023,13 @@
 
 static int bnxt_alloc_tpa_info(struct bnxt *bp)
 {
-	int i, j, total_aggs = 0;
+	int i, j;
 
 	bp->max_tpa = MAX_TPA;
 	if (bp->flags & BNXT_FLAG_CHIP_P5) {
 		if (!bp->max_tpa_v2)
 			return 0;
 		bp->max_tpa = max_t(u16, bp->max_tpa_v2, MAX_TPA_P5);
-		total_aggs = bp->max_tpa * MAX_SKB_FRAGS;
 	}
 
 	for (i = 0; i < bp->rx_nr_rings; i++) {
@@ -3034,12 +3043,12 @@
 
 		if (!(bp->flags & BNXT_FLAG_CHIP_P5))
 			continue;
-		agg = kcalloc(total_aggs, sizeof(*agg), GFP_KERNEL);
-		rxr->rx_tpa[0].agg_arr = agg;
-		if (!agg)
-			return -ENOMEM;
-		for (j = 1; j < bp->max_tpa; j++)
-			rxr->rx_tpa[j].agg_arr = agg + j * MAX_SKB_FRAGS;
+		for (j = 0; j < bp->max_tpa; j++) {
+			agg = kcalloc(MAX_SKB_FRAGS, sizeof(*agg), GFP_KERNEL);
+			if (!agg)
+				return -ENOMEM;
+			rxr->rx_tpa[j].agg_arr = agg;
+		}
 		rxr->rx_tpa_idx_map = kzalloc(sizeof(*rxr->rx_tpa_idx_map),
 					      GFP_KERNEL);
 		if (!rxr->rx_tpa_idx_map)
@@ -3234,6 +3243,7 @@
 		}
 		qidx = bp->tc_to_qidx[j];
 		ring->queue_id = bp->q_info[qidx].queue_id;
+		spin_lock_init(&txr->xdp_tx_lock);
 		if (i < bp->tx_nr_rings_xdp)
 			continue;
 		if (i % bp->tx_nr_rings_per_tc == (bp->tx_nr_rings_per_tc - 1))
@@ -4757,8 +4767,10 @@
 		return rc;
 
 	req->vnic_id = cpu_to_le32(vnic->fw_vnic_id);
-	req->num_mc_entries = cpu_to_le32(vnic->mc_list_count);
-	req->mc_tbl_addr = cpu_to_le64(vnic->mc_list_mapping);
+	if (vnic->rx_mask & CFA_L2_SET_RX_MASK_REQ_MASK_MCAST) {
+		req->num_mc_entries = cpu_to_le32(vnic->mc_list_count);
+		req->mc_tbl_addr = cpu_to_le64(vnic->mc_list_mapping);
+	}
 	req->mask = cpu_to_le32(vnic->rx_mask);
 	return hwrm_req_send_silent(bp, req);
 }
@@ -4869,7 +4881,7 @@
 #endif
 
 static int bnxt_hwrm_set_vnic_filter(struct bnxt *bp, u16 vnic_id, u16 idx,
-				     u8 *mac_addr)
+				     const u8 *mac_addr)
 {
 	struct hwrm_cfa_l2_filter_alloc_output *resp;
 	struct hwrm_cfa_l2_filter_alloc_input *req;
@@ -7429,7 +7441,7 @@
 	u8 flags;
 	int rc;
 
-	if (bp->hwrm_spec_code < 0x10801) {
+	if (bp->hwrm_spec_code < 0x10801 || !BNXT_CHIP_P5_THOR(bp)) {
 		rc = -ENODEV;
 		goto no_ptp;
 	}
@@ -8004,6 +8016,12 @@
 	bp->hwrm_cmd_timeout = le16_to_cpu(resp->def_req_timeout);
 	if (!bp->hwrm_cmd_timeout)
 		bp->hwrm_cmd_timeout = DFLT_HWRM_CMD_TIMEOUT;
+	bp->hwrm_cmd_max_timeout = le16_to_cpu(resp->max_req_timeout) * 1000;
+	if (!bp->hwrm_cmd_max_timeout)
+		bp->hwrm_cmd_max_timeout = HWRM_CMD_MAX_TIMEOUT;
+	else if (bp->hwrm_cmd_max_timeout > HWRM_CMD_MAX_TIMEOUT)
+		netdev_warn(bp->dev, "Device requests max timeout of %d seconds, may trigger hung task watchdog\n",
+			    bp->hwrm_cmd_max_timeout / 1000);
 
 	if (resp->hwrm_intf_maj_8b >= 1) {
 		bp->hwrm_max_req_len = le16_to_cpu(resp->max_req_win_len);
@@ -8581,6 +8599,9 @@
 		goto err_out;
 	}
 
+	if (BNXT_VF(bp))
+		bnxt_hwrm_func_qcfg(bp);
+
 	rc = bnxt_setup_vnic(bp, 0);
 	if (rc)
 		goto err_out;
@@ -8609,6 +8630,9 @@
 	vnic->uc_filter_count = 1;
 
 	vnic->rx_mask = 0;
+	if (test_bit(BNXT_STATE_HALF_OPEN, &bp->state))
+		goto skip_rx_mask;
+
 	if (bp->dev->flags & IFF_BROADCAST)
 		vnic->rx_mask |= CFA_L2_SET_RX_MASK_REQ_MASK_BCAST;
 
@@ -8618,7 +8642,7 @@
 	if (bp->dev->flags & IFF_ALLMULTI) {
 		vnic->rx_mask |= CFA_L2_SET_RX_MASK_REQ_MASK_ALL_MCAST;
 		vnic->mc_list_count = 0;
-	} else {
+	} else if (bp->dev->flags & IFF_MULTICAST) {
 		u32 mask = 0;
 
 		bnxt_mc_list_updated(bp, &mask);
@@ -8629,6 +8653,7 @@
 	if (rc)
 		goto err_out;
 
+skip_rx_mask:
 	rc = bnxt_hwrm_set_coal(bp);
 	if (rc)
 		netdev_warn(bp->dev, "HWRM set coalescing failure rc: %x\n",
@@ -9006,10 +9031,14 @@
 		netdev_err(bp->dev, "ring reservation/IRQ init failure rc: %d\n", rc);
 		return rc;
 	}
-	if (tcs && (bp->tx_nr_rings_per_tc * tcs != bp->tx_nr_rings)) {
+	if (tcs && (bp->tx_nr_rings_per_tc * tcs !=
+		    bp->tx_nr_rings - bp->tx_nr_rings_xdp)) {
 		netdev_err(bp->dev, "tx ring reservation failure\n");
 		netdev_reset_tc(bp->dev);
-		bp->tx_nr_rings_per_tc = bp->tx_nr_rings;
+		if (bp->tx_nr_rings_xdp)
+			bp->tx_nr_rings_per_tc = bp->tx_nr_rings_xdp;
+		else
+			bp->tx_nr_rings_per_tc = bp->tx_nr_rings;
 		return -ENOMEM;
 	}
 	return 0;
@@ -9789,7 +9818,8 @@
 
 	if (flags & FUNC_DRV_IF_CHANGE_RESP_FLAGS_RESC_CHANGE)
 		resc_reinit = true;
-	if (flags & FUNC_DRV_IF_CHANGE_RESP_FLAGS_HOT_FW_RESET_DONE)
+	if (flags & FUNC_DRV_IF_CHANGE_RESP_FLAGS_HOT_FW_RESET_DONE ||
+	    test_bit(BNXT_STATE_FW_RESET_DET, &bp->state))
 		fw_reset = true;
 	else if (bp->fw_health && !bp->fw_health->status_reliable)
 		bnxt_try_map_fw_health_reg(bp);
@@ -10234,6 +10264,12 @@
 	if (irq_re_init)
 		udp_tunnel_nic_reset_ntf(bp->dev);
 
+	if (bp->tx_nr_rings_xdp < num_possible_cpus()) {
+		if (!static_key_enabled(&bnxt_xdp_locking_key))
+			static_branch_enable(&bnxt_xdp_locking_key);
+	} else if (static_key_enabled(&bnxt_xdp_locking_key)) {
+		static_branch_disable(&bnxt_xdp_locking_key);
+	}
 	set_bit(BNXT_STATE_OPEN, &bp->state);
 	bnxt_enable_int(bp);
 	/* Enable TX queues */
@@ -10289,13 +10325,15 @@
 		goto half_open_err;
 	}
 
-	rc = bnxt_alloc_mem(bp, false);
+	rc = bnxt_alloc_mem(bp, true);
 	if (rc) {
 		netdev_err(bp->dev, "bnxt_alloc_mem err: %x\n", rc);
 		goto half_open_err;
 	}
-	rc = bnxt_init_nic(bp, false);
+	set_bit(BNXT_STATE_HALF_OPEN, &bp->state);
+	rc = bnxt_init_nic(bp, true);
 	if (rc) {
+		clear_bit(BNXT_STATE_HALF_OPEN, &bp->state);
 		netdev_err(bp->dev, "bnxt_init_nic err: %x\n", rc);
 		goto half_open_err;
 	}
@@ -10303,7 +10341,7 @@
 
 half_open_err:
 	bnxt_free_skbs(bp);
-	bnxt_free_mem(bp, false);
+	bnxt_free_mem(bp, true);
 	dev_close(bp->dev);
 	return rc;
 }
@@ -10313,9 +10351,10 @@
  */
 void bnxt_half_close_nic(struct bnxt *bp)
 {
-	bnxt_hwrm_resource_free(bp, false, false);
+	bnxt_hwrm_resource_free(bp, false, true);
 	bnxt_free_skbs(bp);
-	bnxt_free_mem(bp, false);
+	bnxt_free_mem(bp, true);
+	clear_bit(BNXT_STATE_HALF_OPEN, &bp->state);
 }
 
 static void bnxt_reenable_sriov(struct bnxt *bp)
@@ -10731,7 +10770,7 @@
 	if (dev->flags & IFF_ALLMULTI) {
 		mask |= CFA_L2_SET_RX_MASK_REQ_MASK_ALL_MCAST;
 		vnic->mc_list_count = 0;
-	} else {
+	} else if (dev->flags & IFF_MULTICAST) {
 		mc_update = bnxt_mc_list_updated(bp, &mask);
 	}
 
@@ -10799,9 +10838,10 @@
 	    !bnxt_promisc_ok(bp))
 		vnic->rx_mask &= ~CFA_L2_SET_RX_MASK_REQ_MASK_PROMISCUOUS;
 	rc = bnxt_hwrm_cfa_l2_set_rx_mask(bp, 0);
-	if (rc && vnic->mc_list_count) {
+	if (rc && (vnic->rx_mask & CFA_L2_SET_RX_MASK_REQ_MASK_MCAST)) {
 		netdev_info(bp->dev, "Failed setting MC filters rc: %d, turning on ALL_MCAST mode\n",
 			    rc);
+		vnic->rx_mask &= ~CFA_L2_SET_RX_MASK_REQ_MASK_MCAST;
 		vnic->rx_mask |= CFA_L2_SET_RX_MASK_REQ_MASK_ALL_MCAST;
 		vnic->mc_list_count = 0;
 		rc = bnxt_hwrm_cfa_l2_set_rx_mask(bp, 0);
@@ -10858,7 +10898,7 @@
 
 	if (bp->flags & BNXT_FLAG_CHIP_P5)
 		return bnxt_rfs_supported(bp);
-	if (!(bp->flags & BNXT_FLAG_MSIX_CAP) || !bnxt_can_reserve_rings(bp))
+	if (!(bp->flags & BNXT_FLAG_MSIX_CAP) || !bnxt_can_reserve_rings(bp) || !bp->rx_nr_rings)
 		return false;
 
 	vnics = 1 + bp->rx_nr_rings;
@@ -11708,6 +11748,8 @@
 		bnxt_cfg_ntp_filters(bp);
 	if (test_and_clear_bit(BNXT_HWRM_EXEC_FWD_REQ_SP_EVENT, &bp->sp_event))
 		bnxt_hwrm_exec_fwd_req(bp);
+	if (test_and_clear_bit(BNXT_HWRM_PF_UNLOAD_SP_EVENT, &bp->sp_event))
+		netdev_info(bp->dev, "Receive PF driver unload event!\n");
 	if (test_and_clear_bit(BNXT_PERIODIC_STATS_SP_EVENT, &bp->sp_event)) {
 		bnxt_hwrm_port_qstats(bp, 0);
 		bnxt_hwrm_port_qstats_ext(bp, 0);
@@ -11882,6 +11924,11 @@
 
 	bp->fw_cap = 0;
 	rc = bnxt_hwrm_ver_get(bp);
+	/* FW may be unresponsive after FLR. FLR must complete within 100 msec
+	 * so wait before continuing with recovery.
+	 */
+	if (rc)
+		msleep(100);
 	bnxt_try_map_fw_health_reg(bp);
 	if (rc) {
 		rc = bnxt_try_recover_fw(bp);
@@ -12577,8 +12624,8 @@
 	rcu_read_lock();
 	hlist_for_each_entry_rcu(fltr, head, hash) {
 		if (bnxt_fltr_match(fltr, new_fltr)) {
+			rc = fltr->sw_id;
 			rcu_read_unlock();
-			rc = 0;
 			goto err_free;
 		}
 	}
@@ -12653,8 +12700,6 @@
 			}
 		}
 	}
-	if (test_and_clear_bit(BNXT_HWRM_PF_UNLOAD_SP_EVENT, &bp->sp_event))
-		netdev_info(bp->dev, "Receive PF driver unload event!\n");
 }
 
 #else
@@ -12665,26 +12710,37 @@
 
 #endif /* CONFIG_RFS_ACCEL */
 
-static int bnxt_udp_tunnel_sync(struct net_device *netdev, unsigned int table)
+static int bnxt_udp_tunnel_set_port(struct net_device *netdev, unsigned int table,
+				    unsigned int entry, struct udp_tunnel_info *ti)
 {
 	struct bnxt *bp = netdev_priv(netdev);
-	struct udp_tunnel_info ti;
 	unsigned int cmd;
 
-	udp_tunnel_nic_get_port(netdev, table, 0, &ti);
-	if (ti.type == UDP_TUNNEL_TYPE_VXLAN)
+	if (ti->type == UDP_TUNNEL_TYPE_VXLAN)
 		cmd = TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN;
 	else
 		cmd = TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE;
 
-	if (ti.port)
-		return bnxt_hwrm_tunnel_dst_port_alloc(bp, ti.port, cmd);
+	return bnxt_hwrm_tunnel_dst_port_alloc(bp, ti->port, cmd);
+}
+
+static int bnxt_udp_tunnel_unset_port(struct net_device *netdev, unsigned int table,
+				      unsigned int entry, struct udp_tunnel_info *ti)
+{
+	struct bnxt *bp = netdev_priv(netdev);
+	unsigned int cmd;
+
+	if (ti->type == UDP_TUNNEL_TYPE_VXLAN)
+		cmd = TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN;
+	else
+		cmd = TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE;
 
 	return bnxt_hwrm_tunnel_dst_port_free(bp, cmd);
 }
 
 static const struct udp_tunnel_nic_info bnxt_udp_tunnels = {
-	.sync_table	= bnxt_udp_tunnel_sync,
+	.set_port	= bnxt_udp_tunnel_set_port,
+	.unset_port	= bnxt_udp_tunnel_unset_port,
 	.flags		= UDP_TUNNEL_NIC_INFO_MAY_SLEEP |
 			  UDP_TUNNEL_NIC_INFO_OPEN_ONLY,
 	.tables		= {
@@ -13064,10 +13120,9 @@
 		goto init_dflt_ring_err;
 
 	bp->tx_nr_rings_per_tc = bp->tx_nr_rings;
-	if (bnxt_rfs_supported(bp) && bnxt_rfs_capable(bp)) {
-		bp->flags |= BNXT_FLAG_RFS;
-		bp->dev->features |= NETIF_F_NTUPLE;
-	}
+
+	bnxt_set_dflt_rfs(bp);
+
 init_dflt_ring_err:
 	bnxt_ulp_irq_restart(bp, rc);
 	return rc;
@@ -13370,7 +13425,9 @@
 	}
 
 	bnxt_inv_fw_health_reg(bp);
-	bnxt_dl_register(bp);
+	rc = bnxt_dl_register(bp);
+	if (rc)
+		goto init_err_dl;
 
 	rc = register_netdev(dev);
 	if (rc)
@@ -13390,6 +13447,7 @@
 
 init_err_cleanup:
 	bnxt_dl_unregister(bp);
+init_err_dl:
 	bnxt_shutdown_tc(bp);
 	bnxt_clear_int_mode(bp);
 
@@ -13634,8 +13692,12 @@
 	rtnl_lock();
 
 	err = bnxt_hwrm_func_qcaps(bp);
-	if (!err && netif_running(netdev))
-		err = bnxt_open(netdev);
+	if (!err) {
+		if (netif_running(netdev))
+			err = bnxt_open(netdev);
+		else
+			err = bnxt_reserve_rings(bp, true);
+	}
 
 	bnxt_ulp_start(bp, err);
 	if (!err) {
@@ -13667,8 +13729,16 @@
 
 static int __init bnxt_init(void)
 {
+	int err;
+
 	bnxt_debug_init();
-	return pci_register_driver(&bnxt_pci_driver);
+	err = pci_register_driver(&bnxt_pci_driver);
+	if (err) {
+		bnxt_debug_exit();
+		return err;
+	}
+
+	return 0;
 }
 
 static void __exit bnxt_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt.h
@@ -584,7 +584,8 @@
 #define BNXT_MAX_MTU		9500
 #define BNXT_MAX_PAGE_MODE_MTU	\
 	((unsigned int)PAGE_SIZE - VLAN_ETH_HLEN - NET_IP_ALIGN -	\
-	 XDP_PACKET_HEADROOM)
+	 XDP_PACKET_HEADROOM - \
+	 SKB_DATA_ALIGN((unsigned int)sizeof(struct skb_shared_info)))
 
 #define BNXT_MIN_PKT_SIZE	52
 
@@ -791,6 +792,8 @@
 	u32			dev_state;
 
 	struct bnxt_ring_struct	tx_ring_struct;
+	/* Synchronize simultaneous xdp_xmit on same ring */
+	spinlock_t		xdp_tx_lock;
 };
 
 #define BNXT_LEGACY_COAL_CMPL_PARAMS					\
@@ -1199,6 +1202,7 @@
 #define BNXT_LINK_SPEED_40GB	PORT_PHY_QCFG_RESP_LINK_SPEED_40GB
 #define BNXT_LINK_SPEED_50GB	PORT_PHY_QCFG_RESP_LINK_SPEED_50GB
 #define BNXT_LINK_SPEED_100GB	PORT_PHY_QCFG_RESP_LINK_SPEED_100GB
+#define BNXT_LINK_SPEED_200GB	PORT_PHY_QCFG_RESP_LINK_SPEED_200GB
 	u16			support_speeds;
 	u16			support_pam4_speeds;
 	u16			auto_link_speeds;	/* fw adv setting */
@@ -1840,6 +1844,7 @@
 #define BNXT_STATE_DRV_REGISTERED	7
 #define BNXT_STATE_PCI_CHANNEL_IO_FROZEN	8
 #define BNXT_STATE_NAPI_DISABLED	9
+#define BNXT_STATE_HALF_OPEN		15	/* For offline ethtool tests */
 
 #define BNXT_NO_FW_ACCESS(bp)					\
 	(test_bit(BNXT_STATE_FW_FATAL_COND, &(bp)->state) ||	\
@@ -1901,7 +1906,8 @@
 
 	u16			hwrm_max_req_len;
 	u16			hwrm_max_ext_req_len;
-	int			hwrm_cmd_timeout;
+	unsigned int		hwrm_cmd_timeout;
+	unsigned int		hwrm_cmd_max_timeout;
 	struct mutex		hwrm_cmd_lock;	/* serialize hwrm messages */
 	struct hwrm_ver_get_output	ver_resp;
 #define FW_VER_STR_LEN		32
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_coredump.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_coredump.c
@@ -0,0 +1,372 @@
+/* Broadcom NetXtreme-C/E network driver.
+ *
+ * Copyright (c) 2021 Broadcom Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/pci.h>
+#include "bnxt_hsi.h"
+#include "bnxt.h"
+#include "bnxt_hwrm.h"
+#include "bnxt_coredump.h"
+
+static int bnxt_hwrm_dbg_dma_data(struct bnxt *bp, void *msg,
+				  struct bnxt_hwrm_dbg_dma_info *info)
+{
+	struct hwrm_dbg_cmn_input *cmn_req = msg;
+	__le16 *seq_ptr = msg + info->seq_off;
+	struct hwrm_dbg_cmn_output *cmn_resp;
+	u16 seq = 0, len, segs_off;
+	dma_addr_t dma_handle;
+	void *dma_buf, *resp;
+	int rc, off = 0;
+
+	dma_buf = hwrm_req_dma_slice(bp, msg, info->dma_len, &dma_handle);
+	if (!dma_buf) {
+		hwrm_req_drop(bp, msg);
+		return -ENOMEM;
+	}
+
+	hwrm_req_timeout(bp, msg, bp->hwrm_cmd_max_timeout);
+	cmn_resp = hwrm_req_hold(bp, msg);
+	resp = cmn_resp;
+
+	segs_off = offsetof(struct hwrm_dbg_coredump_list_output,
+			    total_segments);
+	cmn_req->host_dest_addr = cpu_to_le64(dma_handle);
+	cmn_req->host_buf_len = cpu_to_le32(info->dma_len);
+	while (1) {
+		*seq_ptr = cpu_to_le16(seq);
+		rc = hwrm_req_send(bp, msg);
+		if (rc)
+			break;
+
+		len = le16_to_cpu(*((__le16 *)(resp + info->data_len_off)));
+		if (!seq &&
+		    cmn_req->req_type == cpu_to_le16(HWRM_DBG_COREDUMP_LIST)) {
+			info->segs = le16_to_cpu(*((__le16 *)(resp +
+							      segs_off)));
+			if (!info->segs) {
+				rc = -EIO;
+				break;
+			}
+
+			info->dest_buf_size = info->segs *
+					sizeof(struct coredump_segment_record);
+			info->dest_buf = kmalloc(info->dest_buf_size,
+						 GFP_KERNEL);
+			if (!info->dest_buf) {
+				rc = -ENOMEM;
+				break;
+			}
+		}
+
+		if (info->dest_buf) {
+			if ((info->seg_start + off + len) <=
+			    BNXT_COREDUMP_BUF_LEN(info->buf_len)) {
+				memcpy(info->dest_buf + off, dma_buf, len);
+			} else {
+				rc = -ENOBUFS;
+				break;
+			}
+		}
+
+		if (cmn_req->req_type ==
+				cpu_to_le16(HWRM_DBG_COREDUMP_RETRIEVE))
+			info->dest_buf_size += len;
+
+		if (!(cmn_resp->flags & HWRM_DBG_CMN_FLAGS_MORE))
+			break;
+
+		seq++;
+		off += len;
+	}
+	hwrm_req_drop(bp, msg);
+	return rc;
+}
+
+static int bnxt_hwrm_dbg_coredump_list(struct bnxt *bp,
+				       struct bnxt_coredump *coredump)
+{
+	struct bnxt_hwrm_dbg_dma_info info = {NULL};
+	struct hwrm_dbg_coredump_list_input *req;
+	int rc;
+
+	rc = hwrm_req_init(bp, req, HWRM_DBG_COREDUMP_LIST);
+	if (rc)
+		return rc;
+
+	info.dma_len = COREDUMP_LIST_BUF_LEN;
+	info.seq_off = offsetof(struct hwrm_dbg_coredump_list_input, seq_no);
+	info.data_len_off = offsetof(struct hwrm_dbg_coredump_list_output,
+				     data_len);
+
+	rc = bnxt_hwrm_dbg_dma_data(bp, req, &info);
+	if (!rc) {
+		coredump->data = info.dest_buf;
+		coredump->data_size = info.dest_buf_size;
+		coredump->total_segs = info.segs;
+	}
+	return rc;
+}
+
+static int bnxt_hwrm_dbg_coredump_initiate(struct bnxt *bp, u16 component_id,
+					   u16 segment_id)
+{
+	struct hwrm_dbg_coredump_initiate_input *req;
+	int rc;
+
+	rc = hwrm_req_init(bp, req, HWRM_DBG_COREDUMP_INITIATE);
+	if (rc)
+		return rc;
+
+	hwrm_req_timeout(bp, req, bp->hwrm_cmd_max_timeout);
+	req->component_id = cpu_to_le16(component_id);
+	req->segment_id = cpu_to_le16(segment_id);
+
+	return hwrm_req_send(bp, req);
+}
+
+static int bnxt_hwrm_dbg_coredump_retrieve(struct bnxt *bp, u16 component_id,
+					   u16 segment_id, u32 *seg_len,
+					   void *buf, u32 buf_len, u32 offset)
+{
+	struct hwrm_dbg_coredump_retrieve_input *req;
+	struct bnxt_hwrm_dbg_dma_info info = {NULL};
+	int rc;
+
+	rc = hwrm_req_init(bp, req, HWRM_DBG_COREDUMP_RETRIEVE);
+	if (rc)
+		return rc;
+
+	req->component_id = cpu_to_le16(component_id);
+	req->segment_id = cpu_to_le16(segment_id);
+
+	info.dma_len = COREDUMP_RETRIEVE_BUF_LEN;
+	info.seq_off = offsetof(struct hwrm_dbg_coredump_retrieve_input,
+				seq_no);
+	info.data_len_off = offsetof(struct hwrm_dbg_coredump_retrieve_output,
+				     data_len);
+	if (buf) {
+		info.dest_buf = buf + offset;
+		info.buf_len = buf_len;
+		info.seg_start = offset;
+	}
+
+	rc = bnxt_hwrm_dbg_dma_data(bp, req, &info);
+	if (!rc)
+		*seg_len = info.dest_buf_size;
+
+	return rc;
+}
+
+static void
+bnxt_fill_coredump_seg_hdr(struct bnxt *bp,
+			   struct bnxt_coredump_segment_hdr *seg_hdr,
+			   struct coredump_segment_record *seg_rec, u32 seg_len,
+			   int status, u32 duration, u32 instance)
+{
+	memset(seg_hdr, 0, sizeof(*seg_hdr));
+	memcpy(seg_hdr->signature, "sEgM", 4);
+	if (seg_rec) {
+		seg_hdr->component_id = (__force __le32)seg_rec->component_id;
+		seg_hdr->segment_id = (__force __le32)seg_rec->segment_id;
+		seg_hdr->low_version = seg_rec->version_low;
+		seg_hdr->high_version = seg_rec->version_hi;
+	} else {
+		/* For hwrm_ver_get response Component id = 2
+		 * and Segment id = 0
+		 */
+		seg_hdr->component_id = cpu_to_le32(2);
+		seg_hdr->segment_id = 0;
+	}
+	seg_hdr->function_id = cpu_to_le16(bp->pdev->devfn);
+	seg_hdr->length = cpu_to_le32(seg_len);
+	seg_hdr->status = cpu_to_le32(status);
+	seg_hdr->duration = cpu_to_le32(duration);
+	seg_hdr->data_offset = cpu_to_le32(sizeof(*seg_hdr));
+	seg_hdr->instance = cpu_to_le32(instance);
+}
+
+static void
+bnxt_fill_coredump_record(struct bnxt *bp, struct bnxt_coredump_record *record,
+			  time64_t start, s16 start_utc, u16 total_segs,
+			  int status)
+{
+	time64_t end = ktime_get_real_seconds();
+	u32 os_ver_major = 0, os_ver_minor = 0;
+	struct tm tm;
+
+	time64_to_tm(start, 0, &tm);
+	memset(record, 0, sizeof(*record));
+	memcpy(record->signature, "cOrE", 4);
+	record->flags = 0;
+	record->low_version = 0;
+	record->high_version = 1;
+	record->asic_state = 0;
+	strscpy(record->system_name, utsname()->nodename,
+		sizeof(record->system_name));
+	record->year = cpu_to_le16(tm.tm_year + 1900);
+	record->month = cpu_to_le16(tm.tm_mon + 1);
+	record->day = cpu_to_le16(tm.tm_mday);
+	record->hour = cpu_to_le16(tm.tm_hour);
+	record->minute = cpu_to_le16(tm.tm_min);
+	record->second = cpu_to_le16(tm.tm_sec);
+	record->utc_bias = cpu_to_le16(start_utc);
+	strcpy(record->commandline, "ethtool -w");
+	record->total_segments = cpu_to_le32(total_segs);
+
+	if (sscanf(utsname()->release, "%u.%u", &os_ver_major, &os_ver_minor) != 2)
+		netdev_warn(bp->dev, "Unknown OS release in coredump\n");
+	record->os_ver_major = cpu_to_le32(os_ver_major);
+	record->os_ver_minor = cpu_to_le32(os_ver_minor);
+
+	strscpy(record->os_name, utsname()->sysname, sizeof(record->os_name));
+	time64_to_tm(end, 0, &tm);
+	record->end_year = cpu_to_le16(tm.tm_year + 1900);
+	record->end_month = cpu_to_le16(tm.tm_mon + 1);
+	record->end_day = cpu_to_le16(tm.tm_mday);
+	record->end_hour = cpu_to_le16(tm.tm_hour);
+	record->end_minute = cpu_to_le16(tm.tm_min);
+	record->end_second = cpu_to_le16(tm.tm_sec);
+	record->end_utc_bias = cpu_to_le16(sys_tz.tz_minuteswest * 60);
+	record->asic_id1 = cpu_to_le32(bp->chip_num << 16 |
+				       bp->ver_resp.chip_rev << 8 |
+				       bp->ver_resp.chip_metal);
+	record->asic_id2 = 0;
+	record->coredump_status = cpu_to_le32(status);
+	record->ioctl_low_version = 0;
+	record->ioctl_high_version = 0;
+}
+
+static int __bnxt_get_coredump(struct bnxt *bp, void *buf, u32 *dump_len)
+{
+	u32 ver_get_resp_len = sizeof(struct hwrm_ver_get_output);
+	u32 offset = 0, seg_hdr_len, seg_record_len, buf_len = 0;
+	struct coredump_segment_record *seg_record = NULL;
+	struct bnxt_coredump_segment_hdr seg_hdr;
+	struct bnxt_coredump coredump = {NULL};
+	time64_t start_time;
+	u16 start_utc;
+	int rc = 0, i;
+
+	if (buf)
+		buf_len = *dump_len;
+
+	start_time = ktime_get_real_seconds();
+	start_utc = sys_tz.tz_minuteswest * 60;
+	seg_hdr_len = sizeof(seg_hdr);
+
+	/* First segment should be hwrm_ver_get response */
+	*dump_len = seg_hdr_len + ver_get_resp_len;
+	if (buf) {
+		bnxt_fill_coredump_seg_hdr(bp, &seg_hdr, NULL, ver_get_resp_len,
+					   0, 0, 0);
+		memcpy(buf + offset, &seg_hdr, seg_hdr_len);
+		offset += seg_hdr_len;
+		memcpy(buf + offset, &bp->ver_resp, ver_get_resp_len);
+		offset += ver_get_resp_len;
+	}
+
+	rc = bnxt_hwrm_dbg_coredump_list(bp, &coredump);
+	if (rc) {
+		netdev_err(bp->dev, "Failed to get coredump segment list\n");
+		goto err;
+	}
+
+	*dump_len += seg_hdr_len * coredump.total_segs;
+
+	seg_record = (struct coredump_segment_record *)coredump.data;
+	seg_record_len = sizeof(*seg_record);
+
+	for (i = 0; i < coredump.total_segs; i++) {
+		u16 comp_id = le16_to_cpu(seg_record->component_id);
+		u16 seg_id = le16_to_cpu(seg_record->segment_id);
+		u32 duration = 0, seg_len = 0;
+		unsigned long start, end;
+
+		if (buf && ((offset + seg_hdr_len) >
+			    BNXT_COREDUMP_BUF_LEN(buf_len))) {
+			rc = -ENOBUFS;
+			goto err;
+		}
+
+		start = jiffies;
+
+		rc = bnxt_hwrm_dbg_coredump_initiate(bp, comp_id, seg_id);
+		if (rc) {
+			netdev_err(bp->dev,
+				   "Failed to initiate coredump for seg = %d\n",
+				   seg_record->segment_id);
+			goto next_seg;
+		}
+
+		/* Write segment data into the buffer */
+		rc = bnxt_hwrm_dbg_coredump_retrieve(bp, comp_id, seg_id,
+						     &seg_len, buf, buf_len,
+						     offset + seg_hdr_len);
+		if (rc && rc == -ENOBUFS)
+			goto err;
+		else if (rc)
+			netdev_err(bp->dev,
+				   "Failed to retrieve coredump for seg = %d\n",
+				   seg_record->segment_id);
+
+next_seg:
+		end = jiffies;
+		duration = jiffies_to_msecs(end - start);
+		bnxt_fill_coredump_seg_hdr(bp, &seg_hdr, seg_record, seg_len,
+					   rc, duration, 0);
+
+		if (buf) {
+			/* Write segment header into the buffer */
+			memcpy(buf + offset, &seg_hdr, seg_hdr_len);
+			offset += seg_hdr_len + seg_len;
+		}
+
+		*dump_len += seg_len;
+		seg_record =
+			(struct coredump_segment_record *)((u8 *)seg_record +
+							   seg_record_len);
+	}
+
+err:
+	if (buf)
+		bnxt_fill_coredump_record(bp, buf + offset, start_time,
+					  start_utc, coredump.total_segs + 1,
+					  rc);
+	kfree(coredump.data);
+	*dump_len += sizeof(struct bnxt_coredump_record);
+	if (rc == -ENOBUFS)
+		netdev_err(bp->dev, "Firmware returned large coredump buffer\n");
+	return rc;
+}
+
+int bnxt_get_coredump(struct bnxt *bp, u16 dump_type, void *buf, u32 *dump_len)
+{
+	if (dump_type == BNXT_DUMP_CRASH) {
+#ifdef CONFIG_TEE_BNXT_FW
+		return tee_bnxt_copy_coredump(buf, 0, *dump_len);
+#else
+		return -EOPNOTSUPP;
+#endif
+	} else {
+		return __bnxt_get_coredump(bp, buf, dump_len);
+	}
+}
+
+u32 bnxt_get_coredump_length(struct bnxt *bp, u16 dump_type)
+{
+	u32 len = 0;
+
+	if (dump_type == BNXT_DUMP_CRASH)
+		len = BNXT_CRASH_DUMP_LEN;
+	else
+		__bnxt_get_coredump(bp, NULL, &len);
+	return len;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_coredump.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_coredump.h
@@ -10,6 +10,10 @@
 #ifndef BNXT_COREDUMP_H
 #define BNXT_COREDUMP_H
 
+#include <linux/utsname.h>
+#include <linux/time.h>
+#include <linux/rtc.h>
+
 struct bnxt_coredump_segment_hdr {
 	__u8 signature[4];
 	__le32 component_id;
@@ -63,4 +67,51 @@
 	__u8 ioctl_high_version;
 	__le16 rsvd3[313];
 };
+
+#define BNXT_CRASH_DUMP_LEN	(8 << 20)
+
+#define COREDUMP_LIST_BUF_LEN		2048
+#define COREDUMP_RETRIEVE_BUF_LEN	4096
+
+struct bnxt_coredump {
+	void		*data;
+	int		data_size;
+	u16		total_segs;
+};
+
+#define BNXT_COREDUMP_BUF_LEN(len) ((len) - sizeof(struct bnxt_coredump_record))
+
+struct bnxt_hwrm_dbg_dma_info {
+	void *dest_buf;
+	int dest_buf_size;
+	u16 dma_len;
+	u16 seq_off;
+	u16 data_len_off;
+	u16 segs;
+	u32 seg_start;
+	u32 buf_len;
+};
+
+struct hwrm_dbg_cmn_input {
+	__le16 req_type;
+	__le16 cmpl_ring;
+	__le16 seq_id;
+	__le16 target_id;
+	__le64 resp_addr;
+	__le64 host_dest_addr;
+	__le32 host_buf_len;
+};
+
+struct hwrm_dbg_cmn_output {
+	__le16 error_code;
+	__le16 req_type;
+	__le16 seq_id;
+	__le16 resp_len;
+	u8 flags;
+	#define HWRM_DBG_CMN_FLAGS_MORE	1
+};
+
+int bnxt_get_coredump(struct bnxt *bp, u16 dump_type, void *buf, u32 *dump_len);
+u32 bnxt_get_coredump_length(struct bnxt *bp, u16 dump_type);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c
@@ -134,7 +134,7 @@
 {
 	struct bnxt_fw_health *health = bp->fw_health;
 
-	if (!bp->dl || !health)
+	if (!health)
 		return;
 
 	if (!(bp->fw_cap & BNXT_FW_CAP_HOT_RESET) || health->fw_reset_reporter)
@@ -188,7 +188,7 @@
 {
 	struct bnxt_fw_health *health = bp->fw_health;
 
-	if (!bp->dl || !health)
+	if (!health)
 		return;
 
 	if ((all || !(bp->fw_cap & BNXT_FW_CAP_HOT_RESET)) &&
@@ -781,6 +781,7 @@
 {
 	const struct devlink_ops *devlink_ops;
 	struct devlink_port_attrs attrs = {};
+	struct bnxt_dl *bp_dl;
 	struct devlink *dl;
 	int rc;
 
@@ -795,7 +796,9 @@
 		return -ENOMEM;
 	}
 
-	bnxt_link_bp_to_dl(bp, dl);
+	bp->dl = dl;
+	bp_dl = devlink_priv(dl);
+	bp_dl->bp = bp;
 
 	/* Add switchdev eswitch mode setting, if SRIOV supported */
 	if (pci_find_ext_capability(bp->pdev, PCI_EXT_CAP_ID_SRIOV) &&
@@ -833,7 +836,6 @@
 err_dl_unreg:
 	devlink_unregister(dl);
 err_dl_free:
-	bnxt_link_bp_to_dl(bp, NULL);
 	devlink_free(dl);
 	return rc;
 }
@@ -842,9 +844,6 @@
 {
 	struct devlink *dl = bp->dl;
 
-	if (!dl)
-		return;
-
 	if (BNXT_PF(bp)) {
 		bnxt_dl_params_unregister(bp);
 		devlink_port_unregister(&bp->dl_port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.h
@@ -20,19 +20,6 @@
 	return ((struct bnxt_dl *)devlink_priv(dl))->bp;
 }
 
-/* To clear devlink pointer from bp, pass NULL dl */
-static inline void bnxt_link_bp_to_dl(struct bnxt *bp, struct devlink *dl)
-{
-	bp->dl = dl;
-
-	/* add a back pointer in dl to bp */
-	if (dl) {
-		struct bnxt_dl *bp_dl = devlink_priv(dl);
-
-		bp_dl->bp = bp;
-	}
-}
-
 #define NVM_OFF_MSIX_VEC_PER_PF_MAX	108
 #define NVM_OFF_MSIX_VEC_PER_PF_MIN	114
 #define NVM_OFF_IGNORE_ARI		164
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c
@@ -25,15 +25,13 @@
 #include "bnxt_hsi.h"
 #include "bnxt.h"
 #include "bnxt_hwrm.h"
+#include "bnxt_ulp.h"
 #include "bnxt_xdp.h"
 #include "bnxt_ptp.h"
 #include "bnxt_ethtool.h"
 #include "bnxt_nvm_defs.h"	/* NVRAM content constant and structure defs */
 #include "bnxt_fw_hdr.h"	/* Firmware hdr constant and structure defs */
 #include "bnxt_coredump.h"
-#define FLASH_NVRAM_TIMEOUT	((HWRM_CMD_TIMEOUT) * 100)
-#define FLASH_PACKAGE_TIMEOUT	((HWRM_CMD_TIMEOUT) * 200)
-#define INSTALL_PACKAGE_TIMEOUT	((HWRM_CMD_TIMEOUT) * 200)
 
 static u32 bnxt_get_msglevel(struct net_device *dev)
 {
@@ -134,7 +132,7 @@
 	}
 
 reset_coalesce:
-	if (netif_running(dev)) {
+	if (test_bit(BNXT_STATE_OPEN, &bp->state)) {
 		if (update_stats) {
 			rc = bnxt_close_nic(bp, true, false);
 			if (!rc)
@@ -1672,6 +1670,8 @@
 		return SPEED_50000;
 	case BNXT_LINK_SPEED_100GB:
 		return SPEED_100000;
+	case BNXT_LINK_SPEED_200GB:
+		return SPEED_200000;
 	default:
 		return SPEED_UNKNOWN;
 	}
@@ -1945,6 +1945,9 @@
 	case PORT_PHY_QCFG_RESP_ACTIVE_FEC_FEC_RS272_IEEE_ACTIVE:
 		fec->active_fec |= ETHTOOL_FEC_LLRS;
 		break;
+	case PORT_PHY_QCFG_RESP_ACTIVE_FEC_FEC_NONE_ACTIVE:
+		fec->active_fec |= ETHTOOL_FEC_OFF;
+		break;
 	}
 	return 0;
 }
@@ -2073,9 +2076,7 @@
 		}
 
 		link_info->autoneg |= BNXT_AUTONEG_FLOW_CTRL;
-		if (bp->hwrm_spec_code >= 0x10201)
-			link_info->req_flow_ctrl =
-				PORT_PHY_CFG_REQ_AUTO_PAUSE_AUTONEG_PAUSE;
+		link_info->req_flow_ctrl = 0;
 	} else {
 		/* when transition from auto pause to force pause,
 		 * force a link change
@@ -2167,7 +2168,7 @@
 		req->host_src_addr = cpu_to_le64(dma_handle);
 	}
 
-	hwrm_req_timeout(bp, req, FLASH_NVRAM_TIMEOUT);
+	hwrm_req_timeout(bp, req, bp->hwrm_cmd_max_timeout);
 	req->dir_type = cpu_to_le16(dir_type);
 	req->dir_ordinal = cpu_to_le16(dir_ordinal);
 	req->dir_ext = cpu_to_le16(dir_ext);
@@ -2508,8 +2509,8 @@
 		return rc;
 	}
 
-	hwrm_req_timeout(bp, modify, FLASH_PACKAGE_TIMEOUT);
-	hwrm_req_timeout(bp, install, INSTALL_PACKAGE_TIMEOUT);
+	hwrm_req_timeout(bp, modify, bp->hwrm_cmd_max_timeout);
+	hwrm_req_timeout(bp, install, bp->hwrm_cmd_max_timeout);
 
 	hwrm_req_hold(bp, modify);
 	modify->host_src_addr = cpu_to_le64(dma_handle);
@@ -2708,7 +2709,7 @@
 	if (rc)
 		return rc;
 
-	buflen = dir_entries * entry_length;
+	buflen = mul_u32_u32(dir_entries, entry_length);
 	buf = hwrm_req_dma_slice(bp, req, buflen, &dma_handle);
 	if (!buf) {
 		hwrm_req_drop(bp, req);
@@ -3408,7 +3409,7 @@
 	if (!skb)
 		return -ENOMEM;
 	data = skb_put(skb, pkt_size);
-	eth_broadcast_addr(data);
+	ether_addr_copy(&data[i], bp->dev->dev_addr);
 	i += ETH_ALEN;
 	ether_addr_copy(&data[i], bp->dev->dev_addr);
 	i += ETH_ALEN;
@@ -3502,9 +3503,13 @@
 	if (!offline) {
 		bnxt_run_fw_tests(bp, test_mask, &test_results);
 	} else {
-		rc = bnxt_close_nic(bp, false, false);
-		if (rc)
+		bnxt_ulp_stop(bp);
+		rc = bnxt_close_nic(bp, true, false);
+		if (rc) {
+			etest->flags |= ETH_TEST_FL_FAILED;
+			bnxt_ulp_start(bp, rc);
 			return;
+		}
 		bnxt_run_fw_tests(bp, test_mask, &test_results);
 
 		buf[BNXT_MACLPBK_TEST_IDX] = 1;
@@ -3514,6 +3519,7 @@
 		if (rc) {
 			bnxt_hwrm_mac_loopback(bp, false);
 			etest->flags |= ETH_TEST_FL_FAILED;
+			bnxt_ulp_start(bp, rc);
 			return;
 		}
 		if (bnxt_run_loopback(bp))
@@ -3539,7 +3545,8 @@
 		}
 		bnxt_hwrm_phy_loopback(bp, false, false);
 		bnxt_half_close_nic(bp);
-		rc = bnxt_open_nic(bp, false, true);
+		rc = bnxt_open_nic(bp, true, true);
+		bnxt_ulp_start(bp, rc);
 	}
 	if (rc || bnxt_test_irq(bp)) {
 		buf[BNXT_IRQ_TEST_IDX] = 1;
@@ -3590,7 +3597,7 @@
 		}
 	}
 
-	if (req & BNXT_FW_RESET_AP) {
+	if (!BNXT_CHIP_P4_PLUS(bp) && (req & BNXT_FW_RESET_AP)) {
 		/* This feature is not supported in older firmware versions */
 		if (bp->hwrm_spec_code >= 0x10803) {
 			if (!bnxt_firmware_reset_ap(dev)) {
@@ -3609,337 +3616,6 @@
 	return 0;
 }
 
-static int bnxt_hwrm_dbg_dma_data(struct bnxt *bp, void *msg,
-				  struct bnxt_hwrm_dbg_dma_info *info)
-{
-	struct hwrm_dbg_cmn_input *cmn_req = msg;
-	__le16 *seq_ptr = msg + info->seq_off;
-	struct hwrm_dbg_cmn_output *cmn_resp;
-	u16 seq = 0, len, segs_off;
-	dma_addr_t dma_handle;
-	void *dma_buf, *resp;
-	int rc, off = 0;
-
-	dma_buf = hwrm_req_dma_slice(bp, msg, info->dma_len, &dma_handle);
-	if (!dma_buf) {
-		hwrm_req_drop(bp, msg);
-		return -ENOMEM;
-	}
-
-	hwrm_req_timeout(bp, msg, HWRM_COREDUMP_TIMEOUT);
-	cmn_resp = hwrm_req_hold(bp, msg);
-	resp = cmn_resp;
-
-	segs_off = offsetof(struct hwrm_dbg_coredump_list_output,
-			    total_segments);
-	cmn_req->host_dest_addr = cpu_to_le64(dma_handle);
-	cmn_req->host_buf_len = cpu_to_le32(info->dma_len);
-	while (1) {
-		*seq_ptr = cpu_to_le16(seq);
-		rc = hwrm_req_send(bp, msg);
-		if (rc)
-			break;
-
-		len = le16_to_cpu(*((__le16 *)(resp + info->data_len_off)));
-		if (!seq &&
-		    cmn_req->req_type == cpu_to_le16(HWRM_DBG_COREDUMP_LIST)) {
-			info->segs = le16_to_cpu(*((__le16 *)(resp +
-							      segs_off)));
-			if (!info->segs) {
-				rc = -EIO;
-				break;
-			}
-
-			info->dest_buf_size = info->segs *
-					sizeof(struct coredump_segment_record);
-			info->dest_buf = kmalloc(info->dest_buf_size,
-						 GFP_KERNEL);
-			if (!info->dest_buf) {
-				rc = -ENOMEM;
-				break;
-			}
-		}
-
-		if (info->dest_buf) {
-			if ((info->seg_start + off + len) <=
-			    BNXT_COREDUMP_BUF_LEN(info->buf_len)) {
-				memcpy(info->dest_buf + off, dma_buf, len);
-			} else {
-				rc = -ENOBUFS;
-				break;
-			}
-		}
-
-		if (cmn_req->req_type ==
-				cpu_to_le16(HWRM_DBG_COREDUMP_RETRIEVE))
-			info->dest_buf_size += len;
-
-		if (!(cmn_resp->flags & HWRM_DBG_CMN_FLAGS_MORE))
-			break;
-
-		seq++;
-		off += len;
-	}
-	hwrm_req_drop(bp, msg);
-	return rc;
-}
-
-static int bnxt_hwrm_dbg_coredump_list(struct bnxt *bp,
-				       struct bnxt_coredump *coredump)
-{
-	struct bnxt_hwrm_dbg_dma_info info = {NULL};
-	struct hwrm_dbg_coredump_list_input *req;
-	int rc;
-
-	rc = hwrm_req_init(bp, req, HWRM_DBG_COREDUMP_LIST);
-	if (rc)
-		return rc;
-
-	info.dma_len = COREDUMP_LIST_BUF_LEN;
-	info.seq_off = offsetof(struct hwrm_dbg_coredump_list_input, seq_no);
-	info.data_len_off = offsetof(struct hwrm_dbg_coredump_list_output,
-				     data_len);
-
-	rc = bnxt_hwrm_dbg_dma_data(bp, req, &info);
-	if (!rc) {
-		coredump->data = info.dest_buf;
-		coredump->data_size = info.dest_buf_size;
-		coredump->total_segs = info.segs;
-	}
-	return rc;
-}
-
-static int bnxt_hwrm_dbg_coredump_initiate(struct bnxt *bp, u16 component_id,
-					   u16 segment_id)
-{
-	struct hwrm_dbg_coredump_initiate_input *req;
-	int rc;
-
-	rc = hwrm_req_init(bp, req, HWRM_DBG_COREDUMP_INITIATE);
-	if (rc)
-		return rc;
-
-	hwrm_req_timeout(bp, req, HWRM_COREDUMP_TIMEOUT);
-	req->component_id = cpu_to_le16(component_id);
-	req->segment_id = cpu_to_le16(segment_id);
-
-	return hwrm_req_send(bp, req);
-}
-
-static int bnxt_hwrm_dbg_coredump_retrieve(struct bnxt *bp, u16 component_id,
-					   u16 segment_id, u32 *seg_len,
-					   void *buf, u32 buf_len, u32 offset)
-{
-	struct hwrm_dbg_coredump_retrieve_input *req;
-	struct bnxt_hwrm_dbg_dma_info info = {NULL};
-	int rc;
-
-	rc = hwrm_req_init(bp, req, HWRM_DBG_COREDUMP_RETRIEVE);
-	if (rc)
-		return rc;
-
-	req->component_id = cpu_to_le16(component_id);
-	req->segment_id = cpu_to_le16(segment_id);
-
-	info.dma_len = COREDUMP_RETRIEVE_BUF_LEN;
-	info.seq_off = offsetof(struct hwrm_dbg_coredump_retrieve_input,
-				seq_no);
-	info.data_len_off = offsetof(struct hwrm_dbg_coredump_retrieve_output,
-				     data_len);
-	if (buf) {
-		info.dest_buf = buf + offset;
-		info.buf_len = buf_len;
-		info.seg_start = offset;
-	}
-
-	rc = bnxt_hwrm_dbg_dma_data(bp, req, &info);
-	if (!rc)
-		*seg_len = info.dest_buf_size;
-
-	return rc;
-}
-
-static void
-bnxt_fill_coredump_seg_hdr(struct bnxt *bp,
-			   struct bnxt_coredump_segment_hdr *seg_hdr,
-			   struct coredump_segment_record *seg_rec, u32 seg_len,
-			   int status, u32 duration, u32 instance)
-{
-	memset(seg_hdr, 0, sizeof(*seg_hdr));
-	memcpy(seg_hdr->signature, "sEgM", 4);
-	if (seg_rec) {
-		seg_hdr->component_id = (__force __le32)seg_rec->component_id;
-		seg_hdr->segment_id = (__force __le32)seg_rec->segment_id;
-		seg_hdr->low_version = seg_rec->version_low;
-		seg_hdr->high_version = seg_rec->version_hi;
-	} else {
-		/* For hwrm_ver_get response Component id = 2
-		 * and Segment id = 0
-		 */
-		seg_hdr->component_id = cpu_to_le32(2);
-		seg_hdr->segment_id = 0;
-	}
-	seg_hdr->function_id = cpu_to_le16(bp->pdev->devfn);
-	seg_hdr->length = cpu_to_le32(seg_len);
-	seg_hdr->status = cpu_to_le32(status);
-	seg_hdr->duration = cpu_to_le32(duration);
-	seg_hdr->data_offset = cpu_to_le32(sizeof(*seg_hdr));
-	seg_hdr->instance = cpu_to_le32(instance);
-}
-
-static void
-bnxt_fill_coredump_record(struct bnxt *bp, struct bnxt_coredump_record *record,
-			  time64_t start, s16 start_utc, u16 total_segs,
-			  int status)
-{
-	time64_t end = ktime_get_real_seconds();
-	u32 os_ver_major = 0, os_ver_minor = 0;
-	struct tm tm;
-
-	time64_to_tm(start, 0, &tm);
-	memset(record, 0, sizeof(*record));
-	memcpy(record->signature, "cOrE", 4);
-	record->flags = 0;
-	record->low_version = 0;
-	record->high_version = 1;
-	record->asic_state = 0;
-	strlcpy(record->system_name, utsname()->nodename,
-		sizeof(record->system_name));
-	record->year = cpu_to_le16(tm.tm_year + 1900);
-	record->month = cpu_to_le16(tm.tm_mon + 1);
-	record->day = cpu_to_le16(tm.tm_mday);
-	record->hour = cpu_to_le16(tm.tm_hour);
-	record->minute = cpu_to_le16(tm.tm_min);
-	record->second = cpu_to_le16(tm.tm_sec);
-	record->utc_bias = cpu_to_le16(start_utc);
-	strcpy(record->commandline, "ethtool -w");
-	record->total_segments = cpu_to_le32(total_segs);
-
-	sscanf(utsname()->release, "%u.%u", &os_ver_major, &os_ver_minor);
-	record->os_ver_major = cpu_to_le32(os_ver_major);
-	record->os_ver_minor = cpu_to_le32(os_ver_minor);
-
-	strlcpy(record->os_name, utsname()->sysname, 32);
-	time64_to_tm(end, 0, &tm);
-	record->end_year = cpu_to_le16(tm.tm_year + 1900);
-	record->end_month = cpu_to_le16(tm.tm_mon + 1);
-	record->end_day = cpu_to_le16(tm.tm_mday);
-	record->end_hour = cpu_to_le16(tm.tm_hour);
-	record->end_minute = cpu_to_le16(tm.tm_min);
-	record->end_second = cpu_to_le16(tm.tm_sec);
-	record->end_utc_bias = cpu_to_le16(sys_tz.tz_minuteswest * 60);
-	record->asic_id1 = cpu_to_le32(bp->chip_num << 16 |
-				       bp->ver_resp.chip_rev << 8 |
-				       bp->ver_resp.chip_metal);
-	record->asic_id2 = 0;
-	record->coredump_status = cpu_to_le32(status);
-	record->ioctl_low_version = 0;
-	record->ioctl_high_version = 0;
-}
-
-static int bnxt_get_coredump(struct bnxt *bp, void *buf, u32 *dump_len)
-{
-	u32 ver_get_resp_len = sizeof(struct hwrm_ver_get_output);
-	u32 offset = 0, seg_hdr_len, seg_record_len, buf_len = 0;
-	struct coredump_segment_record *seg_record = NULL;
-	struct bnxt_coredump_segment_hdr seg_hdr;
-	struct bnxt_coredump coredump = {NULL};
-	time64_t start_time;
-	u16 start_utc;
-	int rc = 0, i;
-
-	if (buf)
-		buf_len = *dump_len;
-
-	start_time = ktime_get_real_seconds();
-	start_utc = sys_tz.tz_minuteswest * 60;
-	seg_hdr_len = sizeof(seg_hdr);
-
-	/* First segment should be hwrm_ver_get response */
-	*dump_len = seg_hdr_len + ver_get_resp_len;
-	if (buf) {
-		bnxt_fill_coredump_seg_hdr(bp, &seg_hdr, NULL, ver_get_resp_len,
-					   0, 0, 0);
-		memcpy(buf + offset, &seg_hdr, seg_hdr_len);
-		offset += seg_hdr_len;
-		memcpy(buf + offset, &bp->ver_resp, ver_get_resp_len);
-		offset += ver_get_resp_len;
-	}
-
-	rc = bnxt_hwrm_dbg_coredump_list(bp, &coredump);
-	if (rc) {
-		netdev_err(bp->dev, "Failed to get coredump segment list\n");
-		goto err;
-	}
-
-	*dump_len += seg_hdr_len * coredump.total_segs;
-
-	seg_record = (struct coredump_segment_record *)coredump.data;
-	seg_record_len = sizeof(*seg_record);
-
-	for (i = 0; i < coredump.total_segs; i++) {
-		u16 comp_id = le16_to_cpu(seg_record->component_id);
-		u16 seg_id = le16_to_cpu(seg_record->segment_id);
-		u32 duration = 0, seg_len = 0;
-		unsigned long start, end;
-
-		if (buf && ((offset + seg_hdr_len) >
-			    BNXT_COREDUMP_BUF_LEN(buf_len))) {
-			rc = -ENOBUFS;
-			goto err;
-		}
-
-		start = jiffies;
-
-		rc = bnxt_hwrm_dbg_coredump_initiate(bp, comp_id, seg_id);
-		if (rc) {
-			netdev_err(bp->dev,
-				   "Failed to initiate coredump for seg = %d\n",
-				   seg_record->segment_id);
-			goto next_seg;
-		}
-
-		/* Write segment data into the buffer */
-		rc = bnxt_hwrm_dbg_coredump_retrieve(bp, comp_id, seg_id,
-						     &seg_len, buf, buf_len,
-						     offset + seg_hdr_len);
-		if (rc && rc == -ENOBUFS)
-			goto err;
-		else if (rc)
-			netdev_err(bp->dev,
-				   "Failed to retrieve coredump for seg = %d\n",
-				   seg_record->segment_id);
-
-next_seg:
-		end = jiffies;
-		duration = jiffies_to_msecs(end - start);
-		bnxt_fill_coredump_seg_hdr(bp, &seg_hdr, seg_record, seg_len,
-					   rc, duration, 0);
-
-		if (buf) {
-			/* Write segment header into the buffer */
-			memcpy(buf + offset, &seg_hdr, seg_hdr_len);
-			offset += seg_hdr_len + seg_len;
-		}
-
-		*dump_len += seg_len;
-		seg_record =
-			(struct coredump_segment_record *)((u8 *)seg_record +
-							   seg_record_len);
-	}
-
-err:
-	if (buf)
-		bnxt_fill_coredump_record(bp, buf + offset, start_time,
-					  start_utc, coredump.total_segs + 1,
-					  rc);
-	kfree(coredump.data);
-	*dump_len += sizeof(struct bnxt_coredump_record);
-	if (rc == -ENOBUFS)
-		netdev_err(bp->dev, "Firmware returned large coredump buffer\n");
-	return rc;
-}
-
 static int bnxt_set_dump(struct net_device *dev, struct ethtool_dump *dump)
 {
 	struct bnxt *bp = netdev_priv(dev);
@@ -3971,10 +3647,7 @@
 			bp->ver_resp.hwrm_fw_rsvd_8b;
 
 	dump->flag = bp->dump_flag;
-	if (bp->dump_flag == BNXT_DUMP_CRASH)
-		dump->len = BNXT_CRASH_DUMP_LEN;
-	else
-		bnxt_get_coredump(bp, NULL, &dump->len);
+	dump->len = bnxt_get_coredump_length(bp, bp->dump_flag);
 	return 0;
 }
 
@@ -3989,15 +3662,7 @@
 	memset(buf, 0, dump->len);
 
 	dump->flag = bp->dump_flag;
-	if (dump->flag == BNXT_DUMP_CRASH) {
-#ifdef CONFIG_TEE_BNXT_FW
-		return tee_bnxt_copy_coredump(buf, 0, dump->len);
-#endif
-	} else {
-		return bnxt_get_coredump(bp, buf, &dump->len);
-	}
-
-	return 0;
+	return bnxt_get_coredump(bp, dump->flag, buf, &dump->len);
 }
 
 static int bnxt_get_ts_info(struct net_device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.h
@@ -22,49 +22,6 @@
 	u8 rsvd;
 };
 
-#define COREDUMP_LIST_BUF_LEN		2048
-#define COREDUMP_RETRIEVE_BUF_LEN	4096
-
-struct bnxt_coredump {
-	void		*data;
-	int		data_size;
-	u16		total_segs;
-};
-
-#define BNXT_COREDUMP_BUF_LEN(len) ((len) - sizeof(struct bnxt_coredump_record))
-
-struct bnxt_hwrm_dbg_dma_info {
-	void *dest_buf;
-	int dest_buf_size;
-	u16 dma_len;
-	u16 seq_off;
-	u16 data_len_off;
-	u16 segs;
-	u32 seg_start;
-	u32 buf_len;
-};
-
-struct hwrm_dbg_cmn_input {
-	__le16 req_type;
-	__le16 cmpl_ring;
-	__le16 seq_id;
-	__le16 target_id;
-	__le64 resp_addr;
-	__le64 host_dest_addr;
-	__le32 host_buf_len;
-};
-
-struct hwrm_dbg_cmn_output {
-	__le16 error_code;
-	__le16 req_type;
-	__le16 seq_id;
-	__le16 resp_len;
-	u8 flags;
-	#define HWRM_DBG_CMN_FLAGS_MORE	1
-};
-
-#define BNXT_CRASH_DUMP_LEN	(8 << 20)
-
 #define BNXT_LED_DFLT_ENA				\
 	(PORT_LED_CFG_REQ_ENABLES_LED0_ID |		\
 	 PORT_LED_CFG_REQ_ENABLES_LED0_STATE |		\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_hwrm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_hwrm.c
@@ -496,7 +496,7 @@
 	}
 
 	/* Limit timeout to an upper limit */
-	timeout = min_t(uint, ctx->timeout, HWRM_CMD_MAX_TIMEOUT);
+	timeout = min(ctx->timeout, bp->hwrm_cmd_max_timeout ?: HWRM_CMD_MAX_TIMEOUT);
 	/* convert timeout to usec */
 	timeout *= 1000;
 
@@ -595,18 +595,24 @@
 
 		/* Last byte of resp contains valid bit */
 		valid = ((u8 *)ctx->resp) + len - 1;
-		for (j = 0; j < HWRM_VALID_BIT_DELAY_USEC; j++) {
+		for (j = 0; j < HWRM_VALID_BIT_DELAY_USEC; ) {
 			/* make sure we read from updated DMA memory */
 			dma_rmb();
 			if (*valid)
 				break;
-			usleep_range(1, 5);
+			if (j < 10) {
+				udelay(1);
+				j++;
+			} else {
+				usleep_range(20, 30);
+				j += 20;
+			}
 		}
 
 		if (j >= HWRM_VALID_BIT_DELAY_USEC) {
 			if (!(ctx->flags & BNXT_HWRM_CTX_SILENT))
 				netdev_err(bp->dev, "Error (timeout: %u) msg {0x%x 0x%x} len:%d v:%d\n",
-					   hwrm_total_timeout(i),
+					   hwrm_total_timeout(i) + j,
 					   le16_to_cpu(ctx->req->req_type),
 					   le16_to_cpu(ctx->req->seq_id), len,
 					   *valid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_hwrm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_hwrm.h
@@ -58,11 +58,10 @@
 
 #define BNXT_HWRM_MAX_REQ_LEN		(bp->hwrm_max_req_len)
 #define BNXT_HWRM_SHORT_REQ_LEN		sizeof(struct hwrm_short_input)
-#define HWRM_CMD_MAX_TIMEOUT		40000
+#define HWRM_CMD_MAX_TIMEOUT		40000U
 #define SHORT_HWRM_CMD_TIMEOUT		20
 #define HWRM_CMD_TIMEOUT		(bp->hwrm_cmd_timeout)
 #define HWRM_RESET_TIMEOUT		((HWRM_CMD_TIMEOUT) * 4)
-#define HWRM_COREDUMP_TIMEOUT		((HWRM_CMD_TIMEOUT) * 12)
 #define BNXT_HWRM_TARGET		0xffff
 #define BNXT_HWRM_NO_CMPL_RING		-1
 #define BNXT_HWRM_REQ_MAX_SIZE		128
@@ -95,7 +94,7 @@
 }
 
 
-#define HWRM_VALID_BIT_DELAY_USEC	150
+#define HWRM_VALID_BIT_DELAY_USEC	50000
 
 static inline bool bnxt_cfa_hwrm_message(u16 req_type)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
@@ -61,14 +61,23 @@
 			    u64 *ns)
 {
 	struct bnxt_ptp_cfg *ptp = bp->ptp_cfg;
+	u32 high_before, high_now, low;
 
 	if (test_bit(BNXT_STATE_IN_FW_RESET, &bp->state))
 		return -EIO;
 
+	high_before = readl(bp->bar0 + ptp->refclk_mapped_regs[1]);
 	ptp_read_system_prets(sts);
-	*ns = readl(bp->bar0 + ptp->refclk_mapped_regs[0]);
+	low = readl(bp->bar0 + ptp->refclk_mapped_regs[0]);
 	ptp_read_system_postts(sts);
-	*ns |= (u64)readl(bp->bar0 + ptp->refclk_mapped_regs[1]) << 32;
+	high_now = readl(bp->bar0 + ptp->refclk_mapped_regs[1]);
+	if (high_now != high_before) {
+		ptp_read_system_prets(sts);
+		low = readl(bp->bar0 + ptp->refclk_mapped_regs[0]);
+		ptp_read_system_postts(sts);
+	}
+	*ns = ((u64)high_now << 32) | low;
+
 	return 0;
 }
 
@@ -331,7 +340,7 @@
 	struct bnxt_ptp_cfg *ptp = container_of(ptp_info, struct bnxt_ptp_cfg,
 						ptp_info);
 	struct bnxt *bp = ptp->bp;
-	u8 pin_id;
+	int pin_id;
 	int rc;
 
 	switch (rq->type) {
@@ -339,6 +348,8 @@
 		/* Configure an External PPS IN */
 		pin_id = ptp_find_pin(ptp->ptp_clock, PTP_PF_EXTTS,
 				      rq->extts.index);
+		if (!TSIO_PIN_VALID(pin_id))
+			return -EOPNOTSUPP;
 		if (!on)
 			break;
 		rc = bnxt_ptp_cfg_pin(bp, pin_id, BNXT_PPS_PIN_PPS_IN);
@@ -352,6 +363,8 @@
 		/* Configure a Periodic PPS OUT */
 		pin_id = ptp_find_pin(ptp->ptp_clock, PTP_PF_PEROUT,
 				      rq->perout.index);
+		if (!TSIO_PIN_VALID(pin_id))
+			return -EOPNOTSUPP;
 		if (!on)
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h
@@ -28,7 +28,7 @@
 	u8 state;
 };
 
-#define TSIO_PIN_VALID(pin) ((pin) < (BNXT_MAX_TSIO_PINS))
+#define TSIO_PIN_VALID(pin) ((pin) >= 0 && (pin) < (BNXT_MAX_TSIO_PINS))
 
 #define EVENT_DATA2_PPS_EVENT_TYPE(data2)				\
 	((data2) & ASYNC_EVENT_CMPL_PPS_TIMESTAMP_EVENT_DATA2_EVENT_TYPE)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c
@@ -623,7 +623,7 @@
 		hw_resc->max_stat_ctxs -= le16_to_cpu(req->min_stat_ctx) * n;
 		hw_resc->max_vnics -= le16_to_cpu(req->min_vnics) * n;
 		if (bp->flags & BNXT_FLAG_CHIP_P5)
-			hw_resc->max_irqs -= vf_msix * n;
+			hw_resc->max_nqs -= vf_msix;
 
 		rc = pf->active_vfs;
 	}
@@ -1151,7 +1151,7 @@
 	}
 }
 
-int bnxt_approve_mac(struct bnxt *bp, u8 *mac, bool strict)
+int bnxt_approve_mac(struct bnxt *bp, const u8 *mac, bool strict)
 {
 	struct hwrm_func_vf_cfg_input *req;
 	int rc = 0;
@@ -1246,7 +1246,7 @@
 {
 }
 
-int bnxt_approve_mac(struct bnxt *bp, u8 *mac, bool strict)
+int bnxt_approve_mac(struct bnxt *bp, const u8 *mac, bool strict)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.h
@@ -41,5 +41,5 @@
 void bnxt_sriov_disable(struct bnxt *);
 void bnxt_hwrm_exec_fwd_req(struct bnxt *);
 void bnxt_update_vf_mac(struct bnxt *);
-int bnxt_approve_mac(struct bnxt *, u8 *, bool);
+int bnxt_approve_mac(struct bnxt *, const u8 *, bool);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c
@@ -1868,7 +1868,7 @@
 	struct flow_cls_offload *flower = type_data;
 	struct bnxt *bp = priv->bp;
 
-	if (flower->common.chain_index)
+	if (!tc_cls_can_offload_and_chain0(bp->dev, type_data))
 		return -EOPNOTSUPP;
 
 	switch (type) {
@@ -2075,6 +2075,7 @@
 	rhashtable_destroy(&tc_info->flow_table);
 free_tc_info:
 	kfree(tc_info);
+	bp->tc_info = NULL;
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_ulp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_ulp.c
@@ -252,7 +252,7 @@
 
 	rc = hwrm_req_replace(bp, req, fw_msg->msg, fw_msg->msg_len);
 	if (rc)
-		return rc;
+		goto drop_req;
 
 	hwrm_req_timeout(bp, req, fw_msg->timeout);
 	resp = hwrm_req_hold(bp, req);
@@ -264,6 +264,7 @@
 
 		memcpy(fw_msg->resp, resp, resp_len);
 	}
+drop_req:
 	hwrm_req_drop(bp, req);
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c
@@ -475,7 +475,7 @@
 	dev->features |= pf_dev->features;
 	bnxt_vf_rep_eth_addr_gen(bp->pf.mac_addr, vf_rep->vf_idx,
 				 dev->perm_addr);
-	ether_addr_copy(dev->dev_addr, dev->perm_addr);
+	eth_hw_addr_set(dev, dev->perm_addr);
 	/* Set VF-Rep's max-mtu to the corresponding VF's max-mtu */
 	if (!bnxt_hwrm_vfr_qcfg(bp, vf_rep, &max_mtu))
 		dev->max_mtu = max_mtu;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c
@@ -20,6 +20,8 @@
 #include "bnxt.h"
 #include "bnxt_xdp.h"
 
+DEFINE_STATIC_KEY_FALSE(bnxt_xdp_locking_key);
+
 struct bnxt_sw_tx_bd *bnxt_xmit_bd(struct bnxt *bp,
 				   struct bnxt_tx_ring_info *txr,
 				   dma_addr_t mapping, u32 len)
@@ -227,11 +229,16 @@
 	ring = smp_processor_id() % bp->tx_nr_rings_xdp;
 	txr = &bp->tx_ring[ring];
 
+	if (READ_ONCE(txr->dev_state) == BNXT_DEV_STATE_CLOSING)
+		return -EINVAL;
+
+	if (static_branch_unlikely(&bnxt_xdp_locking_key))
+		spin_lock(&txr->xdp_tx_lock);
+
 	for (i = 0; i < num_frames; i++) {
 		struct xdp_frame *xdp = frames[i];
 
-		if (!txr || !bnxt_tx_avail(bp, txr) ||
-		    !(bp->bnapi[ring]->flags & BNXT_NAPI_FLAG_XDP))
+		if (!bnxt_tx_avail(bp, txr))
 			break;
 
 		mapping = dma_map_single(&pdev->dev, xdp->data, xdp->len,
@@ -250,6 +257,9 @@
 		bnxt_db_write(bp, &txr->tx_db, txr->tx_prod);
 	}
 
+	if (static_branch_unlikely(&bnxt_xdp_locking_key))
+		spin_unlock(&txr->xdp_tx_lock);
+
 	return nxmit;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.h
@@ -10,6 +10,8 @@
 #ifndef BNXT_XDP_H
 #define BNXT_XDP_H
 
+DECLARE_STATIC_KEY_FALSE(bnxt_xdp_locking_key);
+
 struct bnxt_sw_tx_bd *bnxt_xmit_bd(struct bnxt *bp,
 				   struct bnxt_tx_ring_info *txr,
 				   dma_addr_t mapping, u32 len);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -2,7 +2,7 @@
 /*
  * Broadcom GENET (Gigabit Ethernet) controller driver
  *
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
  */
 
 #define pr_fmt(fmt)				"bcmgenet: " fmt
@@ -1248,7 +1248,8 @@
 	}
 }
 
-static void bcmgenet_eee_enable_set(struct net_device *dev, bool enable)
+void bcmgenet_eee_enable_set(struct net_device *dev, bool enable,
+			     bool tx_lpi_enabled)
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
 	u32 off = priv->hw_params->tbuf_offset + TBUF_ENERGY_CTRL;
@@ -1268,7 +1269,7 @@
 
 	/* Enable EEE and switch to a 27Mhz clock automatically */
 	reg = bcmgenet_readl(priv->base + off);
-	if (enable)
+	if (tx_lpi_enabled)
 		reg |= TBUF_EEE_EN | TBUF_PM_EN;
 	else
 		reg &= ~(TBUF_EEE_EN | TBUF_PM_EN);
@@ -1289,6 +1290,7 @@
 
 	priv->eee.eee_enabled = enable;
 	priv->eee.eee_active = enable;
+	priv->eee.tx_lpi_enabled = tx_lpi_enabled;
 }
 
 static int bcmgenet_get_eee(struct net_device *dev, struct ethtool_eee *e)
@@ -1304,6 +1306,7 @@
 
 	e->eee_enabled = p->eee_enabled;
 	e->eee_active = p->eee_active;
+	e->tx_lpi_enabled = p->tx_lpi_enabled;
 	e->tx_lpi_timer = bcmgenet_umac_readl(priv, UMAC_EEE_LPI_TIMER);
 
 	return phy_ethtool_get_eee(dev->phydev, e);
@@ -1313,7 +1316,6 @@
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
 	struct ethtool_eee *p = &priv->eee;
-	int ret = 0;
 
 	if (GENET_IS_V1(priv))
 		return -EOPNOTSUPP;
@@ -1324,16 +1326,11 @@
 	p->eee_enabled = e->eee_enabled;
 
 	if (!p->eee_enabled) {
-		bcmgenet_eee_enable_set(dev, false);
+		bcmgenet_eee_enable_set(dev, false, false);
 	} else {
-		ret = phy_init_eee(dev->phydev, 0);
-		if (ret) {
-			netif_err(priv, hw, dev, "EEE initialization failed\n");
-			return ret;
-		}
-
+		p->eee_active = phy_init_eee(dev->phydev, false) >= 0;
 		bcmgenet_umac_writel(priv, e->tx_lpi_timer, UMAC_EEE_LPI_TIMER);
-		bcmgenet_eee_enable_set(dev, true);
+		bcmgenet_eee_enable_set(dev, p->eee_active, e->tx_lpi_enabled);
 	}
 
 	return phy_ethtool_set_eee(dev->phydev, e);
@@ -1991,6 +1988,11 @@
 	return skb;
 }
 
+static void bcmgenet_hide_tsb(struct sk_buff *skb)
+{
+	__skb_pull(skb, sizeof(struct status_64));
+}
+
 static netdev_tx_t bcmgenet_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
@@ -2085,8 +2087,10 @@
 		/* Note: if we ever change from DMA_TX_APPEND_CRC below we
 		 * will need to restore software padding of "runt" packets
 		 */
+		len_stat |= DMA_TX_APPEND_CRC;
+
 		if (!i) {
-			len_stat |= DMA_TX_APPEND_CRC | DMA_SOP;
+			len_stat |= DMA_SOP;
 			if (skb->ip_summed == CHECKSUM_PARTIAL)
 				len_stat |= DMA_TX_DO_CSUM;
 		}
@@ -2097,6 +2101,8 @@
 	}
 
 	GENET_CB(skb)->last_cb = tx_cb_ptr;
+
+	bcmgenet_hide_tsb(skb);
 	skb_tx_timestamp(skb);
 
 	/* Decrement total BD count and advance our write pointer */
@@ -2243,8 +2249,10 @@
 		dma_length_status = status->length_status;
 		if (dev->features & NETIF_F_RXCSUM) {
 			rx_csum = (__force __be16)(status->rx_csum & 0xffff);
-			skb->csum = (__force __wsum)ntohs(rx_csum);
-			skb->ip_summed = CHECKSUM_COMPLETE;
+			if (rx_csum) {
+				skb->csum = (__force __wsum)ntohs(rx_csum);
+				skb->ip_summed = CHECKSUM_COMPLETE;
+			}
 		}
 
 		/* DMA flags and length are still valid no matter how
@@ -2258,6 +2266,14 @@
 			  __func__, p_index, ring->c_index,
 			  ring->read_ptr, dma_length_status);
 
+		if (unlikely(len > RX_BUF_LENGTH)) {
+			netif_err(priv, rx_status, dev, "oversized packet\n");
+			dev->stats.rx_length_errors++;
+			dev->stats.rx_errors++;
+			dev_kfree_skb_any(skb);
+			goto next;
+		}
+
 		if (unlikely(!(dma_flag & DMA_EOP) || !(dma_flag & DMA_SOP))) {
 			netif_err(priv, rx_status, dev,
 				  "dropping fragmented packet!\n");
@@ -2408,14 +2424,18 @@
 {
 	u32 reg;
 
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
-	if (reg & CMD_SW_RESET)
+	if (reg & CMD_SW_RESET) {
+		spin_unlock_bh(&priv->reg_lock);
 		return;
+	}
 	if (enable)
 		reg |= mask;
 	else
 		reg &= ~mask;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 
 	/* UniMAC stops on a packet boundary, wait for a full-size packet
 	 * to be processed
@@ -2431,8 +2451,10 @@
 	udelay(10);
 
 	/* issue soft reset and disable MAC while updating its registers */
+	spin_lock_bh(&priv->reg_lock);
 	bcmgenet_umac_writel(priv, CMD_SW_RESET, UMAC_CMD);
 	udelay(2);
+	spin_unlock_bh(&priv->reg_lock);
 }
 
 static void bcmgenet_intr_disable(struct bcmgenet_priv *priv)
@@ -3222,7 +3244,7 @@
 }
 
 static void bcmgenet_set_hw_addr(struct bcmgenet_priv *priv,
-				 unsigned char *addr)
+				 const unsigned char *addr)
 {
 	bcmgenet_umac_writel(priv, get_unaligned_be32(&addr[0]), UMAC_MAC0);
 	bcmgenet_umac_writel(priv, get_unaligned_be16(&addr[4]), UMAC_MAC1);
@@ -3240,7 +3262,7 @@
 }
 
 /* Returns a reusable dma control register value */
-static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv)
+static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv, bool flush_rx)
 {
 	unsigned int i;
 	u32 reg;
@@ -3265,6 +3287,14 @@
 	udelay(10);
 	bcmgenet_umac_writel(priv, 0, UMAC_TX_FLUSH);
 
+	if (flush_rx) {
+		reg = bcmgenet_rbuf_ctrl_get(priv);
+		bcmgenet_rbuf_ctrl_set(priv, reg | BIT(0));
+		udelay(10);
+		bcmgenet_rbuf_ctrl_set(priv, reg);
+		udelay(10);
+	}
+
 	return dma_ctrl;
 }
 
@@ -3286,7 +3316,9 @@
 	struct bcmgenet_priv *priv = netdev_priv(dev);
 
 	/* Start the network engine */
+	netif_addr_lock_bh(dev);
 	bcmgenet_set_rx_mode(dev);
+	netif_addr_unlock_bh(dev);
 	bcmgenet_enable_rx_napi(priv);
 
 	umac_enable_set(priv, CMD_TX_EN | CMD_RX_EN, true);
@@ -3328,8 +3360,8 @@
 
 	bcmgenet_set_hw_addr(priv, dev->dev_addr);
 
-	/* Disable RX/TX DMA and flush TX queues */
-	dma_ctrl = bcmgenet_dma_disable(priv);
+	/* Disable RX/TX DMA and flush TX and RX queues */
+	dma_ctrl = bcmgenet_dma_disable(priv, true);
 
 	/* Reinitialize TDMA and RDMA and SW housekeeping */
 	ret = bcmgenet_init_dma(priv);
@@ -3384,7 +3416,7 @@
 	return ret;
 }
 
-static void bcmgenet_netif_stop(struct net_device *dev)
+static void bcmgenet_netif_stop(struct net_device *dev, bool stop_phy)
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
 
@@ -3399,7 +3431,8 @@
 	/* Disable MAC transmit. TX DMA disabled must be done before this */
 	umac_enable_set(priv, CMD_TX_EN, false);
 
-	phy_stop(dev->phydev);
+	if (stop_phy)
+		phy_stop(dev->phydev);
 	bcmgenet_disable_rx_napi(priv);
 	bcmgenet_intr_disable(priv);
 
@@ -3425,7 +3458,7 @@
 
 	netif_dbg(priv, ifdown, dev, "bcmgenet_close\n");
 
-	bcmgenet_netif_stop(dev);
+	bcmgenet_netif_stop(dev, false);
 
 	/* Really kill the PHY state machine and disconnect from it */
 	phy_disconnect(dev->phydev);
@@ -3519,7 +3552,7 @@
 #define MAX_MDF_FILTER	17
 
 static inline void bcmgenet_set_mdf_addr(struct bcmgenet_priv *priv,
-					 unsigned char *addr,
+					 const unsigned char *addr,
 					 int *i)
 {
 	bcmgenet_umac_writel(priv, addr[0] << 8 | addr[1],
@@ -3549,16 +3582,19 @@
 	 * 3. The number of filters needed exceeds the number filters
 	 *    supported by the hardware.
 	*/
+	spin_lock(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	if ((dev->flags & (IFF_PROMISC | IFF_ALLMULTI)) ||
 	    (nfilter > MAX_MDF_FILTER)) {
 		reg |= CMD_PROMISC;
 		bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+		spin_unlock(&priv->reg_lock);
 		bcmgenet_umac_writel(priv, 0, UMAC_MDF_CTRL);
 		return;
 	} else {
 		reg &= ~CMD_PROMISC;
 		bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+		spin_unlock(&priv->reg_lock);
 	}
 
 	/* update MDF filter */
@@ -3592,7 +3628,7 @@
 	if (netif_running(dev))
 		return -EBUSY;
 
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 
 	return 0;
 }
@@ -3941,6 +3977,10 @@
 		goto err;
 	}
 	priv->wol_irq = platform_get_irq_optional(pdev, 2);
+	if (priv->wol_irq == -EPROBE_DEFER) {
+		err = priv->wol_irq;
+		goto err;
+	}
 
 	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base)) {
@@ -3948,6 +3988,7 @@
 		goto err;
 	}
 
+	spin_lock_init(&priv->reg_lock);
 	spin_lock_init(&priv->lock);
 
 	SET_NETDEV_DEV(dev, &pdev->dev);
@@ -3966,10 +4007,12 @@
 
 	/* Request the WOL interrupt and advertise suspend if available */
 	priv->wol_irq_disabled = true;
-	err = devm_request_irq(&pdev->dev, priv->wol_irq, bcmgenet_wol_isr, 0,
-			       dev->name, priv);
-	if (!err)
-		device_set_wakeup_capable(&pdev->dev, 1);
+	if (priv->wol_irq > 0) {
+		err = devm_request_irq(&pdev->dev, priv->wol_irq,
+				       bcmgenet_wol_isr, 0, dev->name, priv);
+		if (!err)
+			device_set_wakeup_capable(&pdev->dev, 1);
+	}
 
 	/* Set the needed headroom to account for any possible
 	 * features enabling/disabling at runtime
@@ -4036,7 +4079,7 @@
 		bcmgenet_power_up(priv, GENET_POWER_PASSIVE);
 
 	if (pd && !IS_ERR_OR_NULL(pd->mac_address))
-		ether_addr_copy(dev->dev_addr, pd->mac_address);
+		eth_hw_addr_set(dev, pd->mac_address);
 	else
 		if (!device_get_mac_address(&pdev->dev, dev->dev_addr, ETH_ALEN))
 			if (has_acpi_companion(&pdev->dev))
@@ -4178,7 +4221,7 @@
 			bcmgenet_hfb_create_rxnfc_filter(priv, rule);
 
 	/* Disable RX/TX DMA and flush TX queues */
-	dma_ctrl = bcmgenet_dma_disable(priv);
+	dma_ctrl = bcmgenet_dma_disable(priv, false);
 
 	/* Reinitialize TDMA and RDMA and SW housekeeping */
 	ret = bcmgenet_init_dma(priv);
@@ -4193,9 +4236,6 @@
 	if (!device_may_wakeup(d))
 		phy_resume(dev->phydev);
 
-	if (priv->eee.eee_enabled)
-		bcmgenet_eee_enable_set(dev, true);
-
 	bcmgenet_netif_start(dev);
 
 	netif_device_attach(dev);
@@ -4219,7 +4259,7 @@
 
 	netif_device_detach(dev);
 
-	bcmgenet_netif_stop(dev);
+	bcmgenet_netif_stop(dev, true);
 
 	if (!device_may_wakeup(d))
 		phy_suspend(dev->phydev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/genet/bcmgenet.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/genet/bcmgenet.h
@@ -572,6 +572,8 @@
 /* device context */
 struct bcmgenet_priv {
 	void __iomem *base;
+	/* reg_lock: lock to serialize access to shared registers */
+	spinlock_t reg_lock;
 	enum bcmgenet_version version;
 	struct net_device *dev;
 
@@ -701,4 +703,7 @@
 void bcmgenet_wol_power_up_cfg(struct bcmgenet_priv *priv,
 			       enum bcmgenet_power_mode mode);
 
+void bcmgenet_eee_enable_set(struct net_device *dev, bool enable,
+			     bool tx_lpi_enabled);
+
 #endif /* __BCMGENET_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
@@ -40,6 +40,13 @@
 void bcmgenet_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
+	struct device *kdev = &priv->pdev->dev;
+
+	if (!device_can_wakeup(kdev)) {
+		wol->supported = 0;
+		wol->wolopts = 0;
+		return;
+	}
 
 	wol->supported = WAKE_MAGIC | WAKE_MAGICSECURE | WAKE_FILTER;
 	wol->wolopts = priv->wolopts;
@@ -126,6 +133,7 @@
 	}
 
 	/* Can't suspend with WoL if MAC is still in reset */
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	if (reg & CMD_SW_RESET)
 		reg &= ~CMD_SW_RESET;
@@ -133,6 +141,7 @@
 	/* disable RX */
 	reg &= ~CMD_RX_EN;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 	mdelay(10);
 
 	if (priv->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE)) {
@@ -178,6 +187,7 @@
 	}
 
 	/* Enable CRC forward */
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	priv->crc_fwd_en = 1;
 	reg |= CMD_CRC_FWD;
@@ -185,6 +195,7 @@
 	/* Receiver must be enabled for WOL MP detection */
 	reg |= CMD_RX_EN;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 
 	reg = UMAC_IRQ_MPD_R;
 	if (hfb_enable)
@@ -231,7 +242,9 @@
 	}
 
 	/* Disable CRC Forward */
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	reg &= ~CMD_CRC_FWD;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -25,6 +25,7 @@
 
 #include "bcmgenet.h"
 
+
 /* setup netdev link state when PHY link status change and
  * update UMAC and RGMII block when link up
  */
@@ -90,6 +91,7 @@
 		reg |= RGMII_LINK;
 		bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
 
+		spin_lock_bh(&priv->reg_lock);
 		reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 		reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
 			       CMD_HD_EN |
@@ -102,6 +104,12 @@
 			reg |= CMD_TX_EN | CMD_RX_EN;
 		}
 		bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+		spin_unlock_bh(&priv->reg_lock);
+
+		priv->eee.eee_active = phy_init_eee(phydev, 0) >= 0;
+		bcmgenet_eee_enable_set(dev,
+					priv->eee.eee_enabled && priv->eee.eee_active,
+					priv->eee.tx_lpi_enabled);
 	} else {
 		/* done if nothing has changed */
 		if (!status_changed)
@@ -165,15 +173,6 @@
 
 static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
 {
-	u32 reg;
-
-	if (!GENET_IS_V5(priv)) {
-		/* Speed settings are set in bcmgenet_mii_setup() */
-		reg = bcmgenet_sys_readl(priv, SYS_PORT_CTRL);
-		reg |= LED_ACT_SOURCE_MAC;
-		bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
-	}
-
 	if (priv->hw_params->flags & GENET_HAS_MOCA_LINK_DET)
 		fixed_phy_set_link_update(priv->dev->phydev,
 					  bcmgenet_fixed_phy_link_update);
@@ -206,6 +205,8 @@
 
 		if (!phy_name) {
 			phy_name = "MoCA";
+			if (!GENET_IS_V5(priv))
+				port_ctrl |= LED_ACT_SOURCE_MAC;
 			bcmgenet_moca_phy_setup(priv);
 		}
 		break;
@@ -265,6 +266,7 @@
 	 * block for the interface to work
 	 */
 	if (priv->ext_phy) {
+		mutex_lock(&phydev->lock);
 		reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
 		reg &= ~ID_MODE_DIS;
 		reg |= id_mode_dis;
@@ -273,6 +275,7 @@
 		else
 			reg |= RGMII_MODE_EN;
 		bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+		mutex_unlock(&phydev->lock);
 	}
 
 	if (init)
@@ -361,6 +364,9 @@
 	if (priv->internal_phy && !GENET_IS_V5(priv))
 		dev->phydev->irq = PHY_MAC_INTERRUPT;
 
+	/* Indicate that the MAC is responsible for PHY PM */
+	dev->phydev->mac_managed_pm = true;
+
 	return 0;
 }
 
@@ -575,7 +581,7 @@
 		};
 
 		phydev = fixed_phy_register(PHY_POLL, &fphy_status, NULL);
-		if (!phydev || IS_ERR(phydev)) {
+		if (IS_ERR(phydev)) {
 			dev_err(kdev, "failed to register fixed PHY device\n");
 			return -ENODEV;
 		}
@@ -631,5 +637,7 @@
 	if (of_phy_is_fixed_link(dn))
 		of_phy_deregister_fixed_link(dn);
 	of_node_put(priv->phy_dn);
+	clk_prepare_enable(priv->clk);
 	platform_device_unregister(priv->mii_pdev);
+	clk_disable_unprepare(priv->clk);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/tg3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/tg3.c
@@ -55,6 +55,7 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/crc32poly.h>
+#include <linux/dmi.h>
 
 #include <net/checksum.h>
 #include <net/ip.h>
@@ -224,6 +225,7 @@
 MODULE_DESCRIPTION("Broadcom Tigon3 ethernet driver");
 MODULE_LICENSE("GPL");
 MODULE_FIRMWARE(FIRMWARE_TG3);
+MODULE_FIRMWARE(FIRMWARE_TG357766);
 MODULE_FIRMWARE(FIRMWARE_TG3TSO);
 MODULE_FIRMWARE(FIRMWARE_TG3TSO5);
 
@@ -6447,6 +6449,14 @@
 	int i;
 	u32 *regs;
 
+	/* If it is a PCI error, all registers will be 0xffff,
+	 * we don't dump them out, just report the error and return
+	 */
+	if (tp->pdev->error_state != pci_channel_io_normal) {
+		netdev_err(tp->dev, "PCI channel ERROR!\n");
+		return;
+	}
+
 	regs = kzalloc(TG3_REG_BLK_SIZE, GFP_ATOMIC);
 	if (!regs)
 		return;
@@ -6853,7 +6863,7 @@
 				       desc_idx, *post_ptr);
 		drop_it_no_recycle:
 			/* Other statistics kept track of by card. */
-			tp->rx_dropped++;
+			tnapi->rx_dropped++;
 			goto next_pkt;
 		}
 
@@ -7879,8 +7889,10 @@
 
 	segs = skb_gso_segment(skb, tp->dev->features &
 				    ~(NETIF_F_TSO | NETIF_F_TSO6));
-	if (IS_ERR(segs) || !segs)
+	if (IS_ERR(segs) || !segs) {
+		tnapi->tx_dropped++;
 		goto tg3_tso_bug_end;
+	}
 
 	skb_list_walk_safe(segs, seg, next) {
 		skb_mark_not_on_list(seg);
@@ -8151,7 +8163,7 @@
 drop:
 	dev_kfree_skb_any(skb);
 drop_nofree:
-	tp->tx_dropped++;
+	tnapi->tx_dropped++;
 	return NETDEV_TX_OK;
 }
 
@@ -9330,7 +9342,7 @@
 /* tp->lock is held. */
 static int tg3_halt(struct tg3 *tp, int kind, bool silent)
 {
-	int err;
+	int err, i;
 
 	tg3_stop_fw(tp);
 
@@ -9351,6 +9363,13 @@
 
 		/* And make sure the next sample is new data */
 		memset(tp->hw_stats, 0, sizeof(struct tg3_hw_stats));
+
+		for (i = 0; i < TG3_IRQ_MAX_VECS; ++i) {
+			struct tg3_napi *tnapi = &tp->napi[i];
+
+			tnapi->rx_dropped = 0;
+			tnapi->tx_dropped = 0;
+		}
 	}
 
 	return err;
@@ -11176,7 +11195,8 @@
 	rtnl_lock();
 	tg3_full_lock(tp, 0);
 
-	if (!netif_running(tp->dev)) {
+	if (tp->pcierr_recovery || !netif_running(tp->dev) ||
+	    tp->pdev->error_state != pci_channel_io_normal) {
 		tg3_flag_clear(tp, RESET_TASK_PENDING);
 		tg3_full_unlock(tp);
 		rtnl_unlock();
@@ -11905,6 +11925,9 @@
 {
 	struct rtnl_link_stats64 *old_stats = &tp->net_stats_prev;
 	struct tg3_hw_stats *hw_stats = tp->hw_stats;
+	unsigned long rx_dropped;
+	unsigned long tx_dropped;
+	int i;
 
 	stats->rx_packets = old_stats->rx_packets +
 		get_stat64(&hw_stats->rx_ucast_packets) +
@@ -11951,8 +11974,26 @@
 	stats->rx_missed_errors = old_stats->rx_missed_errors +
 		get_stat64(&hw_stats->rx_discards);
 
-	stats->rx_dropped = tp->rx_dropped;
-	stats->tx_dropped = tp->tx_dropped;
+	/* Aggregate per-queue counters. The per-queue counters are updated
+	 * by a single writer, race-free. The result computed by this loop
+	 * might not be 100% accurate (counters can be updated in the middle of
+	 * the loop) but the next tg3_get_nstats() will recompute the current
+	 * value so it is acceptable.
+	 *
+	 * Note that these counters wrap around at 4G on 32bit machines.
+	 */
+	rx_dropped = (unsigned long)(old_stats->rx_dropped);
+	tx_dropped = (unsigned long)(old_stats->tx_dropped);
+
+	for (i = 0; i < tp->irq_cnt; i++) {
+		struct tg3_napi *tnapi = &tp->napi[i];
+
+		rx_dropped += tnapi->rx_dropped;
+		tx_dropped += tnapi->tx_dropped;
+	}
+
+	stats->rx_dropped = rx_dropped;
+	stats->tx_dropped = tx_dropped;
 }
 
 static int tg3_get_regs_len(struct net_device *dev)
@@ -17699,6 +17740,9 @@
 	} else
 		persist_dma_mask = dma_mask = DMA_BIT_MASK(64);
 
+	if (tg3_asic_rev(tp) == ASIC_REV_57766)
+		persist_dma_mask = DMA_BIT_MASK(31);
+
 	/* Configure DMA attributes. */
 	if (dma_mask > DMA_BIT_MASK(32)) {
 		err = dma_set_mask(&pdev->dev, dma_mask);
@@ -18073,12 +18117,59 @@
 
 static SIMPLE_DEV_PM_OPS(tg3_pm_ops, tg3_suspend, tg3_resume);
 
+/* Systems where ACPI _PTS (Prepare To Sleep) S5 will result in a fatal
+ * PCIe AER event on the tg3 device if the tg3 device is not, or cannot
+ * be, powered down.
+ */
+static const struct dmi_system_id tg3_restart_aer_quirk_table[] = {
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PowerEdge R440"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PowerEdge R540"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PowerEdge R640"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PowerEdge R650"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PowerEdge R740"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "PowerEdge R750"),
+		},
+	},
+	{}
+};
+
 static void tg3_shutdown(struct pci_dev *pdev)
 {
 	struct net_device *dev = pci_get_drvdata(pdev);
 	struct tg3 *tp = netdev_priv(dev);
 
+	tg3_reset_task_cancel(tp);
+
 	rtnl_lock();
+
 	netif_device_detach(dev);
 
 	if (netif_running(dev))
@@ -18086,8 +18177,23 @@
 
 	if (system_state == SYSTEM_POWER_OFF)
 		tg3_power_down(tp);
+	else if (system_state == SYSTEM_RESTART &&
+		 dmi_first_match(tg3_restart_aer_quirk_table) &&
+		 pdev->current_state != PCI_D3cold &&
+		 pdev->current_state != PCI_UNKNOWN) {
+		/* Disable PCIe AER on the tg3 to avoid a fatal
+		 * error during this system restart.
+		 */
+		pcie_capability_clear_word(pdev, PCI_EXP_DEVCTL,
+					   PCI_EXP_DEVCTL_CERE |
+					   PCI_EXP_DEVCTL_NFERE |
+					   PCI_EXP_DEVCTL_FERE |
+					   PCI_EXP_DEVCTL_URRE);
+	}
 
 	rtnl_unlock();
+
+	pci_disable_device(pdev);
 }
 
 /**
@@ -18107,6 +18213,9 @@
 
 	netdev_info(netdev, "PCI I/O error detected\n");
 
+	/* Want to make sure that the reset task doesn't run */
+	tg3_reset_task_cancel(tp);
+
 	rtnl_lock();
 
 	/* Could be second call or maybe we don't have netdev yet */
@@ -18123,9 +18232,6 @@
 
 	tg3_timer_stop(tp);
 
-	/* Want to make sure that the reset task doesn't run */
-	tg3_reset_task_cancel(tp);
-
 	netif_device_detach(netdev);
 
 	/* Clean up software state, even if MMIO is blocked */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/broadcom/tg3.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/broadcom/tg3.h
@@ -3018,6 +3018,7 @@
 	u16				*rx_rcb_prod_idx;
 	struct tg3_rx_prodring_set	prodring;
 	struct tg3_rx_buffer_desc	*rx_rcb;
+	unsigned long			rx_dropped;
 
 	u32				tx_prod	____cacheline_aligned;
 	u32				tx_cons;
@@ -3026,6 +3027,7 @@
 	u32				prodmbox;
 	struct tg3_tx_buffer_desc	*tx_ring;
 	struct tg3_tx_ring_info		*tx_buffers;
+	unsigned long			tx_dropped;
 
 	dma_addr_t			status_mapping;
 	dma_addr_t			rx_rcb_mapping;
@@ -3219,8 +3221,6 @@
 
 
 	/* begin "everything else" cacheline(s) section */
-	unsigned long			rx_dropped;
-	unsigned long			tx_dropped;
 	struct rtnl_link_stats64	net_stats_prev;
 	struct tg3_ethtool_stats	estats_prev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/brocade/bna/bna_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/brocade/bna/bna_types.h
@@ -410,7 +410,7 @@
 /* Tx object */
 
 /* Tx datapath control structure */
-#define BNA_Q_NAME_SIZE		16
+#define BNA_Q_NAME_SIZE		(IFNAMSIZ + 6)
 struct bna_tcb {
 	/* Fast path */
 	void			**sw_qpt;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/brocade/bna/bnad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/brocade/bna/bnad.c
@@ -875,7 +875,7 @@
 
 	ether_addr_copy(netdev->perm_addr, bnad->perm_addr);
 	if (is_zero_ether_addr(netdev->dev_addr))
-		ether_addr_copy(netdev->dev_addr, bnad->perm_addr);
+		eth_hw_addr_set(netdev, bnad->perm_addr);
 }
 
 /* Control Path Handlers */
@@ -1535,8 +1535,9 @@
 
 	for (i = 0; i < num_txqs; i++) {
 		vector_num = tx_info->tcb[i]->intr_vector;
-		sprintf(tx_info->tcb[i]->name, "%s TXQ %d", bnad->netdev->name,
-				tx_id + tx_info->tcb[i]->id);
+		snprintf(tx_info->tcb[i]->name, BNA_Q_NAME_SIZE, "%s TXQ %d",
+			 bnad->netdev->name,
+			 tx_id + tx_info->tcb[i]->id);
 		err = request_irq(bnad->msix_table[vector_num].vector,
 				  (irq_handler_t)bnad_msix_tx, 0,
 				  tx_info->tcb[i]->name,
@@ -1586,9 +1587,9 @@
 
 	for (i = 0; i < num_rxps; i++) {
 		vector_num = rx_info->rx_ctrl[i].ccb->intr_vector;
-		sprintf(rx_info->rx_ctrl[i].ccb->name, "%s CQ %d",
-			bnad->netdev->name,
-			rx_id + rx_info->rx_ctrl[i].ccb->id);
+		snprintf(rx_info->rx_ctrl[i].ccb->name, BNA_Q_NAME_SIZE,
+			 "%s CQ %d", bnad->netdev->name,
+			 rx_id + rx_info->rx_ctrl[i].ccb->id);
 		err = request_irq(bnad->msix_table[vector_num].vector,
 				  (irq_handler_t)bnad_msix_rx, 0,
 				  rx_info->rx_ctrl[i].ccb->name,
@@ -1881,7 +1882,6 @@
 	return rcvd;
 }
 
-#define BNAD_NAPI_POLL_QUOTA		64
 static void
 bnad_napi_add(struct bnad *bnad, u32 rx_id)
 {
@@ -1892,7 +1892,7 @@
 	for (i = 0; i <	bnad->num_rxp_per_rx; i++) {
 		rx_ctrl = &bnad->rx_info[rx_id].rx_ctrl[i];
 		netif_napi_add(bnad->netdev, &rx_ctrl->napi,
-			       bnad_napi_poll_rx, BNAD_NAPI_POLL_QUOTA);
+			       bnad_napi_poll_rx, NAPI_POLL_WEIGHT);
 	}
 }
 
@@ -3249,7 +3249,7 @@
 
 	err = bnad_mac_addr_set_locked(bnad, sa->sa_data);
 	if (!err)
-		ether_addr_copy(netdev->dev_addr, sa->sa_data);
+		eth_hw_addr_set(netdev, sa->sa_data);
 
 	spin_unlock_irqrestore(&bnad->bna_lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/brocade/bna/bnad_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/brocade/bna/bnad_debugfs.c
@@ -312,7 +312,7 @@
 	void *kern_buf;
 
 	/* Copy the user space buf */
-	kern_buf = memdup_user(buf, nbytes);
+	kern_buf = memdup_user_nul(buf, nbytes);
 	if (IS_ERR(kern_buf))
 		return PTR_ERR(kern_buf);
 
@@ -372,7 +372,7 @@
 	void *kern_buf;
 
 	/* Copy the user space buf */
-	kern_buf = memdup_user(buf, nbytes);
+	kern_buf = memdup_user_nul(buf, nbytes);
 	if (IS_ERR(kern_buf))
 		return PTR_ERR(kern_buf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cadence/macb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cadence/macb.h
@@ -12,6 +12,7 @@
 #include <linux/ptp_clock_kernel.h>
 #include <linux/net_tstamp.h>
 #include <linux/interrupt.h>
+#include <linux/phy/phy.h>
 
 #if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT) || defined(CONFIG_MACB_USE_HWSTAMP)
 #define MACB_EXT_DESC
@@ -81,6 +82,7 @@
 #define GEM_NCFGR		0x0004 /* Network Config */
 #define GEM_USRIO		0x000c /* User IO */
 #define GEM_DMACFG		0x0010 /* DMA Configuration */
+#define GEM_PBUFRXCUT		0x0044 /* RX Partial Store and Forward */
 #define GEM_JML			0x0048 /* Jumbo Max Length */
 #define GEM_HS_MAC_CONFIG	0x0050 /* GEM high speed config */
 #define GEM_HRB			0x0080 /* Hash Bottom */
@@ -93,6 +95,8 @@
 #define GEM_SA3T		0x009C /* Specific3 Top */
 #define GEM_SA4B		0x00A0 /* Specific4 Bottom */
 #define GEM_SA4T		0x00A4 /* Specific4 Top */
+#define GEM_RXPTPUNI	0x00D4 /* PTP RX Unicast address */
+#define GEM_TXPTPUNI	0x00D8 /* PTP TX Unicast address */
 #define GEM_WOL			0x00b8 /* Wake on LAN */
 #define GEM_EFTSH		0x00e8 /* PTP Event Frame Transmitted Seconds Register 47:32 */
 #define GEM_EFRSH		0x00ec /* PTP Event Frame Received Seconds Register 47:32 */
@@ -244,6 +248,8 @@
 #define MACB_TZQ_OFFSET		12 /* Transmit zero quantum pause frame */
 #define MACB_TZQ_SIZE		1
 #define MACB_SRTSM_OFFSET	15
+#define MACB_PTPUNI_OFFSET			20
+#define MACB_PTPUNI_SIZE			1
 #define MACB_OSSMODE_OFFSET 24 /* Enable One Step Synchro Mode */
 #define MACB_OSSMODE_SIZE	1
 
@@ -339,6 +345,11 @@
 #define GEM_ADDR64_OFFSET	30 /* Address bus width - 64b or 32b */
 #define GEM_ADDR64_SIZE		1
 
+/* Bitfields in PBUFRXCUT */
+#define GEM_WTRMRK_OFFSET	0 /* Watermark value offset */
+#define GEM_WTRMRK_SIZE		12
+#define GEM_ENCUTTHRU_OFFSET	31 /* Enable RX partial store and forward */
+#define GEM_ENCUTTHRU_SIZE	1
 
 /* Bitfields in NSR */
 #define MACB_NSR_LINK_OFFSET	0 /* pcs_link_state */
@@ -403,7 +414,7 @@
 #define MACB_PFR_SIZE		1
 #define MACB_PTZ_OFFSET		13 /* Enable pause time zero interrupt */
 #define MACB_PTZ_SIZE		1
-#define MACB_WOL_OFFSET		14 /* Enable wake-on-lan interrupt */
+#define MACB_WOL_OFFSET		28 /* Enable WOL received interrupt */
 #define MACB_WOL_SIZE		1
 #define MACB_DRQFR_OFFSET	18 /* PTP Delay Request Frame Received */
 #define MACB_DRQFR_SIZE		1
@@ -629,6 +640,9 @@
 #define GEM_T2OFST_OFFSET			0 /* offset value */
 #define GEM_T2OFST_SIZE				7
 
+/* Bitfields in queue pointer registers */
+#define GEM_RBQP_DISABLE	0x1
+
 /* Offset for screener type 2 compare values (T2CMPOFST).
  * Note the offset is applied after the specified point,
  * e.g. GEM_T2COMPOFST_ETYPE denotes the EtherType field, so an offset
@@ -713,8 +727,12 @@
 #define MACB_CAPS_GEM_HAS_PTP			0x00000040
 #define MACB_CAPS_BD_RD_PREFETCH		0x00000080
 #define MACB_CAPS_NEEDS_RSTONUBR		0x00000100
+#define MACB_CAPS_PARTIAL_STORE_FORWARD		0x00000800
+#define MACB_CAPS_WOL				0x00000200
 #define MACB_CAPS_CLK_HW_CHG			0x04000000
 #define MACB_CAPS_MACB_IS_EMAC			0x08000000
+#define MACB_CAPS_NEED_TSUCLK			0x00001000
+#define MACB_CAPS_QUEUE_DISABLE			0x00002000
 #define MACB_CAPS_FIFO_MODE			0x10000000
 #define MACB_CAPS_GIGABIT_MODE_AVAILABLE	0x20000000
 #define MACB_CAPS_SG_DISABLED			0x40000000
@@ -1241,6 +1259,7 @@
 	u32	(*macb_reg_readl)(struct macb *bp, int offset);
 	void	(*macb_reg_writel)(struct macb *bp, int offset, u32 value);
 
+	struct macb_dma_desc	*rx_ring_tieoff;
 	size_t			rx_buffer_size;
 
 	unsigned int		rx_ring_size;
@@ -1258,11 +1277,15 @@
 	struct clk		*rx_clk;
 	struct clk		*tsu_clk;
 	struct net_device	*dev;
+	/* Protects hw_stats and ethtool_stats */
+	spinlock_t		stats_lock;
 	union {
 		struct macb_stats	macb;
 		struct gem_stats	gem;
 	}			hw_stats;
 
+	dma_addr_t		rx_ring_tieoff_dma;
+
 	struct macb_or_gem_ops	macbgem_ops;
 
 	struct mii_bus		*mii_bus;
@@ -1286,7 +1309,13 @@
 
 	u32			wol;
 
+	/* holds value of rx watermark value for pbuf_rxcutthru register */
+	u16			rx_watermark;
+
 	struct macb_ptp_info	*ptp_info;	/* macb-ptp interface */
+
+	struct phy		*sgmii_phy;	/* for ZynqMP SGMII mode */
+
 #ifdef MACB_EXT_DESC
 	uint8_t hw_dma_cap;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cadence/macb_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cadence/macb_main.c
@@ -34,7 +34,13 @@
 #include <linux/udp.h>
 #include <linux/tcp.h>
 #include <linux/iopoll.h>
+#include <linux/phy/phy.h>
 #include <linux/pm_runtime.h>
+#include <linux/ptp_classify.h>
+#include <linux/crc32.h>
+#include <linux/inetdevice.h>
+#include <linux/reset.h>
+#include <linux/firmware/xlnx-zynqmp.h>
 #include "macb.h"
 
 /* This structure is only used for MACB on SiFive FU540 devices */
@@ -90,8 +96,7 @@
 /* Graceful stop timeouts in us. We should allow up to
  * 1 frame time (10 Mbits/s, full-duplex, ignoring collisions)
  */
-#define MACB_HALT_TIMEOUT	1230
-
+#define MACB_HALT_TIMEOUT	14000
 #define MACB_PM_TIMEOUT  100 /* ms */
 
 #define MACB_MDIO_TIMEOUT	1000000 /* in usecs */
@@ -284,6 +289,9 @@
 	top = cpu_to_le16(*((u16 *)(bp->dev->dev_addr + 4)));
 	macb_or_gem_writel(bp, SA1T, top);
 
+	gem_writel(bp, RXPTPUNI, bottom);
+	gem_writel(bp, TXPTPUNI, bottom);
+
 	/* Clear unused address register sets */
 	macb_or_gem_writel(bp, SA2B, 0);
 	macb_or_gem_writel(bp, SA2T, 0);
@@ -793,7 +801,8 @@
 	spin_unlock_irqrestore(&bp->lock, flags);
 
 	/* Enable Rx and Tx */
-	macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(RE) | MACB_BIT(TE));
+	macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(RE) | MACB_BIT(TE) |
+		    MACB_BIT(PTPUNI));
 
 	netif_tx_wake_all_queues(ndev);
 }
@@ -858,6 +867,13 @@
 		return ret;
 	}
 
+	/* Since this driver uses runtime handling of clocks, initiate a phy
+	 * reset if the attached phy requires it. Check return to see if phy
+	 * was reset and then do a phy initialization.
+	 */
+	if (phy_reset_after_clk_enable(dev->phydev) == 1)
+		phy_init_hw(dev->phydev);
+
 	phylink_start(bp->phylink);
 
 	return 0;
@@ -879,6 +895,7 @@
 
 	bp->phylink_config.dev = &dev->dev;
 	bp->phylink_config.type = PHYLINK_NETDEV;
+	bp->phylink_config.mac_managed_pm = true;
 
 	if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII) {
 		bp->phylink_config.poll_fixed_state = true;
@@ -898,10 +915,8 @@
 
 static int macb_mdiobus_register(struct macb *bp)
 {
-	struct device_node *child, *np = bp->pdev->dev.of_node;
-
-	if (of_phy_is_fixed_link(np))
-		return mdiobus_register(bp->mii_bus);
+	struct device_node *child, *np = bp->pdev->dev.of_node, *mdio_np, *dev_np;
+	struct platform_device *mdio_pdev = NULL;
 
 	/* Only create the PHY from the device tree if at least one PHY is
 	 * described. Otherwise scan the entire MDIO bus. We do this to support
@@ -918,13 +933,47 @@
 			return of_mdiobus_register(bp->mii_bus, np);
 		}
 
+	/* For shared MDIO usecases find out MDIO producer platform
+	 * device node by traversing through phy-handle DT property.
+	 */
+	np = of_parse_phandle(np, "phy-handle", 0);
+	mdio_np = of_get_parent(np);
+	of_node_put(np);
+	dev_np = of_get_parent(mdio_np);
+	of_node_put(mdio_np);
+	/* Handle error where bus_find_device returns a match for NULL */
+	if (dev_np)
+		mdio_pdev = of_find_device_by_node(dev_np);
+
+	of_node_put(dev_np);
+
+	/* Check if the MDIO producer device is probed */
+	if (mdio_pdev && !dev_get_drvdata(&mdio_pdev->dev)) {
+		platform_device_put(mdio_pdev);
+		netdev_info(bp->dev, "Defer probe as mdio producer %s is not probed\n",
+			    dev_name(&mdio_pdev->dev));
+		return -EPROBE_DEFER;
+	}
+
+	platform_device_put(mdio_pdev);
 	return mdiobus_register(bp->mii_bus);
 }
 
 static int macb_mii_init(struct macb *bp)
 {
+	struct device_node *mdio_np, *child, *np = bp->pdev->dev.of_node;
 	int err = -ENXIO;
 
+	/* With fixed-link, we don't need to register the MDIO bus,
+	 * except if we have a child named "mdio" in the device tree.
+	 * In that case, some devices may be attached to the MACB's MDIO bus.
+	 */
+	child = of_get_child_by_name(np, "mdio");
+	if (child)
+		of_node_put(child);
+	else if (of_phy_is_fixed_link(np))
+		return macb_mii_probe(bp->dev);
+
 	/* Enable management port */
 	macb_writel(bp, NCR, MACB_BIT(MPE));
 
@@ -940,13 +989,21 @@
 	snprintf(bp->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x",
 		 bp->pdev->name, bp->pdev->id);
 	bp->mii_bus->priv = bp;
-	bp->mii_bus->parent = &bp->pdev->dev;
+	bp->mii_bus->parent = &bp->dev->dev;
 
 	dev_set_drvdata(&bp->dev->dev, bp->mii_bus);
 
-	err = macb_mdiobus_register(bp);
-	if (err)
-		goto err_out_free_mdiobus;
+	mdio_np = of_get_child_by_name(np, "mdio");
+	if (mdio_np) {
+		of_node_put(mdio_np);
+		err = of_mdiobus_register(bp->mii_bus, mdio_np);
+		if (err)
+			goto err_out_free_mdiobus;
+	} else {
+		err = macb_mdiobus_register(bp);
+		if (err)
+			goto err_out_free_mdiobus;
+	}
 
 	err = macb_mii_probe(bp->dev);
 	if (err)
@@ -1042,6 +1099,10 @@
 	}
 #endif
 	addr |= MACB_BF(RX_WADDR, MACB_BFEXT(RX_WADDR, desc->addr));
+#ifdef CONFIG_MACB_USE_HWSTAMP
+	if (bp->hw_dma_cap & HW_DMA_CAP_PTP)
+		addr &= ~GEM_BIT(DMA_RXVALID);
+#endif
 	return addr;
 }
 
@@ -1055,6 +1116,7 @@
 	struct sk_buff		*skb;
 	unsigned int		tail;
 	unsigned long		flags;
+	bool			halt_timeout = false;
 
 	netdev_vdbg(bp->dev, "macb_tx_error_task: q = %u, t = %u, h = %u\n",
 		    (unsigned int)(queue - bp->queues),
@@ -1075,9 +1137,11 @@
 	 * (in case we have just queued new packets)
 	 * macb/gem must be halted to write TBQP register
 	 */
-	if (macb_halt_tx(bp))
-		/* Just complain for now, reinitializing TX path can be good */
+	if (macb_halt_tx(bp)) {
 		netdev_err(bp->dev, "BUG: halt tx timed out\n");
+		macb_writel(bp, NCR, macb_readl(bp, NCR) & (~MACB_BIT(TE)));
+		halt_timeout = true;
+	}
 
 	/* Treat frames in TX queue including the ones that caused the error.
 	 * Free transmit buffers in upper layer.
@@ -1148,6 +1212,9 @@
 	macb_writel(bp, TSR, macb_readl(bp, TSR));
 	queue_writel(queue, IER, MACB_TX_INT_FLAGS);
 
+	if (halt_timeout)
+		macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TE));
+
 	/* Now we are ready to start transmission again */
 	netif_tx_start_all_queues(bp->dev);
 	macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TSTART));
@@ -1155,6 +1222,36 @@
 	spin_unlock_irqrestore(&bp->lock, flags);
 }
 
+static bool ptp_one_step_sync(struct sk_buff *skb)
+{
+	struct ptp_header *hdr;
+	unsigned int ptp_class;
+	u8 msgtype;
+
+	/* No need to parse packet if PTP TS is not involved */
+	if (likely(!(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)))
+		goto not_oss;
+
+	/* Identify and return whether PTP one step sync is being processed */
+	ptp_class = ptp_classify_raw(skb);
+	if (ptp_class == PTP_CLASS_NONE)
+		goto not_oss;
+
+	hdr = ptp_parse_header(skb, ptp_class);
+	if (!hdr)
+		goto not_oss;
+
+	if (hdr->flag_field[0] & PTP_FLAG_TWOSTEP)
+		goto not_oss;
+
+	msgtype = ptp_get_msgtype(hdr, ptp_class);
+	if (msgtype == PTP_MSGTYPE_SYNC)
+		return true;
+
+not_oss:
+	return false;
+}
+
 static void macb_tx_interrupt(struct macb_queue *queue)
 {
 	unsigned int tail;
@@ -1199,8 +1296,8 @@
 
 			/* First, update TX stats if needed */
 			if (skb) {
-				if (unlikely(skb_shinfo(skb)->tx_flags &
-					     SKBTX_HW_TSTAMP) &&
+				if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
+				    !ptp_one_step_sync(skb) &&
 				    gem_ptp_do_txstamp(queue, skb, desc) == 0) {
 					/* skb now belongs to timestamp buffer
 					 * and will be removed later
@@ -1250,7 +1347,6 @@
 		/* Make hw descriptor updates visible to CPU */
 		rmb();
 
-		queue->rx_prepared_head++;
 		desc = macb_rx_desc(queue, entry);
 
 		if (!queue->rx_skbuff[entry]) {
@@ -1289,6 +1385,7 @@
 			dma_wmb();
 			desc->addr &= ~MACB_BIT(RX_USED);
 		}
+		queue->rx_prepared_head++;
 	}
 
 	/* Make descriptor updates visible to hardware */
@@ -1319,6 +1416,15 @@
 	 */
 }
 
+static int macb_validate_hw_csum(struct sk_buff *skb)
+{
+	u32 pkt_csum = *((u32 *)&skb->data[skb->len - ETH_FCS_LEN]);
+	u32 csum  = ~crc32_le(~0, skb_mac_header(skb),
+			skb->len + ETH_HLEN - ETH_FCS_LEN);
+
+	return (pkt_csum != csum);
+}
+
 static int gem_rx(struct macb_queue *queue, struct napi_struct *napi,
 		  int budget)
 {
@@ -1380,6 +1486,16 @@
 				 bp->rx_buffer_size, DMA_FROM_DEVICE);
 
 		skb->protocol = eth_type_trans(skb, bp->dev);
+
+		/* Validate MAC fcs if RX checsum offload disabled */
+		if (!(bp->dev->features & NETIF_F_RXCSUM)) {
+			if (macb_validate_hw_csum(skb)) {
+				netdev_err(bp->dev, "incorrect FCS\n");
+				bp->dev->stats.rx_dropped++;
+				break;
+			}
+		}
+
 		skb_checksum_none_assert(skb);
 		if (bp->dev->features & NETIF_F_RXCSUM &&
 		    !(bp->dev->flags & IFF_PROMISC) &&
@@ -1477,6 +1593,19 @@
 			break;
 	}
 
+	/* Validate MAC fcs if RX checsum offload disabled */
+	if (!(bp->dev->features & NETIF_F_RXCSUM)) {
+		if (macb_validate_hw_csum(skb)) {
+			netdev_err(bp->dev, "incorrect FCS\n");
+			bp->dev->stats.rx_dropped++;
+
+			/* Make descriptor updates visible to hardware */
+			wmb();
+
+			return 1;
+		}
+	}
+
 	/* Make descriptor updates visible to hardware */
 	wmb();
 
@@ -1606,7 +1735,14 @@
 	if (work_done < budget) {
 		napi_complete_done(napi, work_done);
 
-		/* Packets received while interrupts were disabled */
+		/* RSR bits only seem to propagate to raise interrupts when
+		 * interrupts are enabled at the time, so if bits are already
+		 * set due to packets received while interrupts were disabled,
+		 * they will not cause another interrupt to be generated when
+		 * interrupts are re-enabled.
+		 * Check for this case here. This has been seen to happen
+		 * around 30% of the time under heavy network load.
+		 */
 		status = macb_readl(bp, RSR);
 		if (status) {
 			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
@@ -1614,6 +1750,22 @@
 			napi_reschedule(napi);
 		} else {
 			queue_writel(queue, IER, bp->rx_intr_mask);
+
+			/* In rare cases, packets could have been received in
+			 * the window between the check above and re-enabling
+			 * interrupts. Therefore, a double-check is required
+			 * to avoid losing a wakeup. This can potentially race
+			 * with the interrupt handler doing the same actions
+			 * if an interrupt is raised just after enabling them,
+			 * but this should be harmless.
+			 */
+			status = macb_readl(bp, RSR);
+			if (unlikely(status)) {
+				queue_writel(queue, IDR, bp->rx_intr_mask);
+				if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+					queue_writel(queue, ISR, MACB_BIT(RCOMP));
+				napi_schedule(napi);
+			}
 		}
 	}
 
@@ -1666,6 +1818,7 @@
 	unsigned int head = queue->tx_head;
 	unsigned int tail = queue->tx_tail;
 	struct macb *bp = queue->bp;
+	unsigned int head_idx, tbqp;
 
 	if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
 		queue_writel(queue, ISR, MACB_BIT(TXUBR));
@@ -1673,65 +1826,14 @@
 	if (head == tail)
 		return;
 
-	macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TSTART));
-}
-
-static irqreturn_t macb_wol_interrupt(int irq, void *dev_id)
-{
-	struct macb_queue *queue = dev_id;
-	struct macb *bp = queue->bp;
-	u32 status;
-
-	status = queue_readl(queue, ISR);
+	tbqp = queue_readl(queue, TBQP) / macb_dma_desc_get_size(bp);
+	tbqp = macb_adj_dma_desc_idx(bp, macb_tx_ring_wrap(bp, tbqp));
+	head_idx = macb_adj_dma_desc_idx(bp, macb_tx_ring_wrap(bp, head));
 
-	if (unlikely(!status))
-		return IRQ_NONE;
-
-	spin_lock(&bp->lock);
-
-	if (status & MACB_BIT(WOL)) {
-		queue_writel(queue, IDR, MACB_BIT(WOL));
-		macb_writel(bp, WOL, 0);
-		netdev_vdbg(bp->dev, "MACB WoL: queue = %u, isr = 0x%08lx\n",
-			    (unsigned int)(queue - bp->queues),
-			    (unsigned long)status);
-		if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
-			queue_writel(queue, ISR, MACB_BIT(WOL));
-		pm_wakeup_event(&bp->pdev->dev, 0);
-	}
-
-	spin_unlock(&bp->lock);
-
-	return IRQ_HANDLED;
-}
-
-static irqreturn_t gem_wol_interrupt(int irq, void *dev_id)
-{
-	struct macb_queue *queue = dev_id;
-	struct macb *bp = queue->bp;
-	u32 status;
-
-	status = queue_readl(queue, ISR);
-
-	if (unlikely(!status))
-		return IRQ_NONE;
-
-	spin_lock(&bp->lock);
-
-	if (status & GEM_BIT(WOL)) {
-		queue_writel(queue, IDR, GEM_BIT(WOL));
-		gem_writel(bp, WOL, 0);
-		netdev_vdbg(bp->dev, "GEM WoL: queue = %u, isr = 0x%08lx\n",
-			    (unsigned int)(queue - bp->queues),
-			    (unsigned long)status);
-		if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
-			queue_writel(queue, ISR, GEM_BIT(WOL));
-		pm_wakeup_event(&bp->pdev->dev, 0);
-	}
-
-	spin_unlock(&bp->lock);
+	if (tbqp == head_idx)
+		return;
 
-	return IRQ_HANDLED;
+	macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TSTART));
 }
 
 static irqreturn_t macb_interrupt(int irq, void *dev_id)
@@ -1749,6 +1851,12 @@
 	spin_lock(&bp->lock);
 
 	while (status) {
+		if (status & MACB_BIT(WOL)) {
+			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+				queue_writel(queue, ISR, MACB_BIT(WOL));
+			break;
+		}
+
 		/* close possible race with dev_close */
 		if (unlikely(!netif_running(dev))) {
 			queue_writel(queue, IDR, -1);
@@ -1817,10 +1925,12 @@
 
 		if (status & MACB_BIT(ISR_ROVR)) {
 			/* We missed at least one packet */
+			spin_lock(&bp->stats_lock);
 			if (macb_is_gem(bp))
 				bp->hw_stats.gem.rx_overruns++;
 			else
 				bp->hw_stats.macb.rx_overruns++;
+			spin_unlock(&bp->stats_lock);
 
 			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
 				queue_writel(queue, ISR, MACB_BIT(ISR_ROVR));
@@ -1999,7 +2109,9 @@
 			ctrl |= MACB_BF(TX_LSO, lso_ctrl);
 			ctrl |= MACB_BF(TX_TCP_SEQ_SRC, seq_ctrl);
 			if ((bp->dev->features & NETIF_F_HW_CSUM) &&
-			    skb->ip_summed != CHECKSUM_PARTIAL && !lso_ctrl)
+			    skb->ip_summed != CHECKSUM_PARTIAL && !lso_ctrl &&
+			    !ptp_one_step_sync(skb) &&
+			    (skb->data_len == 0))
 				ctrl |= MACB_BIT(TX_NOCRC);
 		} else
 			/* Only set MSS/MFS on payload descriptors
@@ -2090,23 +2202,21 @@
 	bool cloned = skb_cloned(*skb) || skb_header_cloned(*skb) ||
 		      skb_is_nonlinear(*skb);
 	int padlen = ETH_ZLEN - (*skb)->len;
-	int headroom = skb_headroom(*skb);
 	int tailroom = skb_tailroom(*skb);
 	struct sk_buff *nskb;
 	u32 fcs;
 
+	/* Not available for GSO and fragments */
 	if (!(ndev->features & NETIF_F_HW_CSUM) ||
 	    !((*skb)->ip_summed != CHECKSUM_PARTIAL) ||
-	    skb_shinfo(*skb)->gso_size)	/* Not available for GSO */
+	    skb_shinfo(*skb)->gso_size || ptp_one_step_sync(*skb) ||
+	    ((*skb)->data_len > 0))
 		return 0;
 
 	if (padlen <= 0) {
 		/* FCS could be appeded to tailroom. */
 		if (tailroom >= ETH_FCS_LEN)
 			goto add_fcs;
-		/* FCS could be appeded by moving data to headroom. */
-		else if (!cloned && headroom + tailroom >= ETH_FCS_LEN)
-			padlen = 0;
 		/* No room for FCS, need to reallocate skb. */
 		else
 			padlen = ETH_FCS_LEN;
@@ -2115,10 +2225,7 @@
 		padlen += ETH_FCS_LEN;
 	}
 
-	if (!cloned && headroom + tailroom >= padlen) {
-		(*skb)->data = memmove((*skb)->head, (*skb)->data, (*skb)->len);
-		skb_set_tail_pointer(*skb, (*skb)->len);
-	} else {
+	if (cloned || tailroom < padlen) {
 		nskb = skb_copy_expand(*skb, 0, padlen, GFP_ATOMIC);
 		if (!nskb)
 			return -ENOMEM;
@@ -2311,6 +2418,12 @@
 
 	bp->macbgem_ops.mog_free_rx_buffers(bp);
 
+	if (bp->rx_ring_tieoff) {
+		dma_free_coherent(&bp->pdev->dev, macb_dma_desc_get_size(bp),
+				  bp->rx_ring_tieoff, bp->rx_ring_tieoff_dma);
+		bp->rx_ring_tieoff = NULL;
+	}
+
 	for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue) {
 		kfree(queue->tx_skb);
 		queue->tx_skb = NULL;
@@ -2400,6 +2513,16 @@
 	if (bp->macbgem_ops.mog_alloc_rx_buffers(bp))
 		goto out_err;
 
+	/* Required for tie off descriptor for PM cases */
+	if (!(bp->caps & MACB_CAPS_QUEUE_DISABLE)) {
+		bp->rx_ring_tieoff = dma_alloc_coherent(&bp->pdev->dev,
+							macb_dma_desc_get_size(bp),
+							&bp->rx_ring_tieoff_dma,
+							GFP_KERNEL);
+		if (!bp->rx_ring_tieoff)
+			goto out_err;
+	}
+
 	return 0;
 
 out_err:
@@ -2407,6 +2530,19 @@
 	return -ENOMEM;
 }
 
+static void macb_init_tieoff(struct macb *bp)
+{
+	struct macb_dma_desc *d = bp->rx_ring_tieoff;
+
+	if (bp->num_queues > 1) {
+		/* Setup a wrapping descriptor with no free slots
+		 * (WRAP and USED) to tie off/disable unused RX queues.
+		 */
+		macb_set_addr(bp, d, MACB_BIT(RX_WRAP) | MACB_BIT(RX_USED));
+		d->ctrl = 0;
+	}
+}
+
 static void gem_init_rings(struct macb *bp)
 {
 	struct macb_queue *queue;
@@ -2430,6 +2566,9 @@
 		gem_rx_refill(queue);
 	}
 
+	if (!(bp->caps & MACB_CAPS_QUEUE_DISABLE))
+		macb_init_tieoff(bp);
+
 }
 
 static void macb_init_rings(struct macb *bp)
@@ -2447,6 +2586,8 @@
 	bp->queues[0].tx_head = 0;
 	bp->queues[0].tx_tail = 0;
 	desc->ctrl |= MACB_BIT(TX_WRAP);
+
+	macb_init_tieoff(bp);
 }
 
 static void macb_reset_hw(struct macb *bp)
@@ -2469,6 +2610,10 @@
 	macb_writel(bp, TSR, -1);
 	macb_writel(bp, RSR, -1);
 
+	/* Disable RX partial store and forward and reset watermark value */
+	if (bp->caps & MACB_CAPS_PARTIAL_STORE_FORWARD)
+		gem_writel(bp, PBUFRXCUT, 0xFFF);
+
 	/* Disable all interrupts */
 	for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue) {
 		queue_writel(queue, IDR, -1);
@@ -2602,7 +2747,11 @@
 
 	config = macb_mdc_clk_div(bp);
 	config |= MACB_BF(RBOF, NET_IP_ALIGN);	/* Make eth data aligned */
-	config |= MACB_BIT(DRFCS);		/* Discard Rx FCS */
+
+	/* Do not discard Rx FCS if RX checsum offload disabled */
+	if (bp->dev->features & NETIF_F_RXCSUM)
+		config |= MACB_BIT(DRFCS);		/* Discard Rx FCS */
+
 	if (bp->caps & MACB_CAPS_JUMBO)
 		config |= MACB_BIT(JFRAME);	/* Enable jumbo frames */
 	else
@@ -2622,6 +2771,15 @@
 		bp->rx_frm_len_mask = MACB_RX_JFRMLEN_MASK;
 
 	macb_configure_dma(bp);
+
+	/* Enable RX partial store and forward and set watermark */
+	if (bp->caps & MACB_CAPS_PARTIAL_STORE_FORWARD) {
+		gem_writel(bp, PBUFRXCUT,
+			   (gem_readl(bp, PBUFRXCUT) &
+			   GEM_BF(WTRMRK, bp->rx_watermark)) |
+			   GEM_BIT(ENCUTTHRU));
+	}
+
 }
 
 /* The hash address register is 64 bits long and takes up two
@@ -2772,10 +2930,14 @@
 
 	macb_init_hw(bp);
 
-	err = macb_phylink_connect(bp);
+	err = phy_power_on(bp->sgmii_phy);
 	if (err)
 		goto reset_hw;
 
+	err = macb_phylink_connect(bp);
+	if (err)
+		goto phy_off;
+
 	netif_tx_start_all_queues(dev);
 
 	if (bp->ptp_info)
@@ -2783,6 +2945,9 @@
 
 	return 0;
 
+phy_off:
+	phy_power_off(bp->sgmii_phy);
+
 reset_hw:
 	macb_reset_hw(bp);
 	for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue)
@@ -2808,6 +2973,8 @@
 	phylink_stop(bp->phylink);
 	phylink_disconnect_phy(bp->phylink);
 
+	phy_power_off(bp->sgmii_phy);
+
 	spin_lock_irqsave(&bp->lock, flags);
 	macb_reset_hw(bp);
 	netif_carrier_off(dev);
@@ -2870,6 +3037,7 @@
 	if (!netif_running(bp->dev))
 		return nstat;
 
+	spin_lock_irq(&bp->stats_lock);
 	gem_update_stats(bp);
 
 	nstat->rx_errors = (hwstat->rx_frame_check_sequence_errors +
@@ -2899,6 +3067,7 @@
 	nstat->tx_aborted_errors = hwstat->tx_excessive_collisions;
 	nstat->tx_carrier_errors = hwstat->tx_carrier_sense_errors;
 	nstat->tx_fifo_errors = hwstat->tx_underrun;
+	spin_unlock_irq(&bp->stats_lock);
 
 	return nstat;
 }
@@ -2906,12 +3075,13 @@
 static void gem_get_ethtool_stats(struct net_device *dev,
 				  struct ethtool_stats *stats, u64 *data)
 {
-	struct macb *bp;
+	struct macb *bp = netdev_priv(dev);
 
-	bp = netdev_priv(dev);
+	spin_lock_irq(&bp->stats_lock);
 	gem_update_stats(bp);
 	memcpy(data, &bp->ethtool_stats, sizeof(u64)
 			* (GEM_STATS_LEN + QUEUE_STATS_LEN * MACB_MAX_QUEUES));
+	spin_unlock_irq(&bp->stats_lock);
 }
 
 static int gem_get_sset_count(struct net_device *dev, int sset)
@@ -2961,6 +3131,7 @@
 		return gem_get_stats(bp);
 
 	/* read stats from hardware */
+	spin_lock_irq(&bp->stats_lock);
 	macb_update_stats(bp);
 
 	/* Convert HW stats into netdevice stats */
@@ -2994,6 +3165,7 @@
 	nstat->tx_carrier_errors = hwstat->tx_carrier_errors;
 	nstat->tx_fifo_errors = hwstat->tx_underruns;
 	/* Don't know about heartbeat or window errors... */
+	spin_unlock_irq(&bp->stats_lock);
 
 	return nstat;
 }
@@ -3040,38 +3212,30 @@
 {
 	struct macb *bp = netdev_priv(netdev);
 
-	if (bp->wol & MACB_WOL_HAS_MAGIC_PACKET) {
-		phylink_ethtool_get_wol(bp->phylink, wol);
-		wol->supported |= WAKE_MAGIC;
+	memset(wol, 0, sizeof(struct ethtool_wolinfo));
 
-		if (bp->wol & MACB_WOL_ENABLED)
-			wol->wolopts |= WAKE_MAGIC;
+	if (bp->caps & MACB_CAPS_WOL) {
+		wol->supported = WAKE_ARP;
+
+		if (bp->wol)
+			wol->wolopts |= WAKE_ARP;
 	}
 }
 
 static int macb_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 {
 	struct macb *bp = netdev_priv(netdev);
-	int ret;
-
-	/* Pass the order to phylink layer */
-	ret = phylink_ethtool_set_wol(bp->phylink, wol);
-	/* Don't manage WoL on MAC if handled by the PHY
-	 * or if there's a failure in talking to the PHY
-	 */
-	if (!ret || ret != -EOPNOTSUPP)
-		return ret;
 
-	if (!(bp->wol & MACB_WOL_HAS_MAGIC_PACKET) ||
-	    (wol->wolopts & ~WAKE_MAGIC))
+	if (!(bp->caps & MACB_CAPS_WOL) ||
+	    (wol->wolopts & ~WAKE_ARP))
 		return -EOPNOTSUPP;
 
-	if (wol->wolopts & WAKE_MAGIC)
-		bp->wol |= MACB_WOL_ENABLED;
+	if (wol->wolopts & WAKE_ARP)
+		bp->wol = 1;
 	else
-		bp->wol &= ~MACB_WOL_ENABLED;
+		bp->wol = 0;
 
-	device_set_wakeup_enable(&bp->pdev->dev, bp->wol & MACB_WOL_ENABLED);
+	device_set_wakeup_enable(&bp->dev->dev, bp->wol);
 
 	return 0;
 }
@@ -3529,8 +3693,6 @@
 	.get_regs		= macb_get_regs,
 	.get_link		= ethtool_op_get_link,
 	.get_ts_info		= ethtool_op_get_ts_info,
-	.get_wol		= macb_get_wol,
-	.set_wol		= macb_set_wol,
 	.get_link_ksettings     = macb_get_link_ksettings,
 	.set_link_ksettings     = macb_set_link_ksettings,
 	.get_ringparam		= macb_get_ringparam,
@@ -3540,8 +3702,6 @@
 static const struct ethtool_ops gem_ethtool_ops = {
 	.get_regs_len		= macb_get_regs_len,
 	.get_regs		= macb_get_regs,
-	.get_wol		= macb_get_wol,
-	.set_wol		= macb_set_wol,
 	.get_link		= ethtool_op_get_link,
 	.get_ts_info		= macb_get_ts_info,
 	.get_ethtool_stats	= gem_get_ethtool_stats,
@@ -3553,6 +3713,8 @@
 	.set_ringparam		= macb_set_ringparam,
 	.get_rxnfc			= gem_get_rxnfc,
 	.set_rxnfc			= gem_set_rxnfc,
+	.get_wol		= macb_get_wol,
+	.set_wol		= macb_set_wol,
 };
 
 static int macb_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
@@ -3682,10 +3844,29 @@
 				const struct macb_config *dt_conf)
 {
 	u32 dcfg;
+	int retval;
 
 	if (dt_conf)
 		bp->caps = dt_conf->caps;
 
+	/* By default we set to partial store and forward mode for zynqmp.
+	 * Disable if not set in devicetree.
+	 */
+	if (bp->caps & MACB_CAPS_PARTIAL_STORE_FORWARD) {
+		retval = of_property_read_u16(bp->pdev->dev.of_node,
+					      "rx-watermark",
+					      &bp->rx_watermark);
+
+		/* Disable partial store and forward in case of error or
+		 * invalid watermark value
+		 */
+		if (retval || bp->rx_watermark > 0xFFF) {
+			dev_info(&bp->pdev->dev,
+				 "Not enabling partial store and forward\n");
+			bp->caps &= ~MACB_CAPS_PARTIAL_STORE_FORWARD;
+		}
+	}
+
 	if (hw_is_gem(bp->regs, bp->native_io)) {
 		bp->caps |= MACB_CAPS_MACB_IS_GEM;
 
@@ -3938,6 +4119,8 @@
 	/* Checksum offload is only available on gem with packet buffer */
 	if (macb_is_gem(bp) && !(bp->caps & MACB_CAPS_FIFO_MODE))
 		dev->hw_features |= NETIF_F_HW_CSUM | NETIF_F_RXCSUM;
+	if (bp->caps & MACB_CAPS_PARTIAL_STORE_FORWARD)
+		dev->hw_features &= ~NETIF_F_RXCSUM;
 	if (bp->caps & MACB_CAPS_SG_DISABLED)
 		dev->hw_features &= ~NETIF_F_SG;
 	dev->features = dev->hw_features;
@@ -4573,10 +4756,82 @@
 	.usrio = &macb_default_usrio,
 };
 
+static int zynqmp_init(struct platform_device *pdev)
+{
+	struct net_device *dev = platform_get_drvdata(pdev);
+	struct macb *bp = netdev_priv(dev);
+	int ret;
+
+	if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+		/* Ensure PS-GTR PHY device used in SGMII mode is ready */
+		bp->sgmii_phy = devm_phy_optional_get(&pdev->dev, NULL);
+
+		if (IS_ERR(bp->sgmii_phy)) {
+			ret = PTR_ERR(bp->sgmii_phy);
+			dev_err_probe(&pdev->dev, ret,
+				      "failed to get PS-GTR PHY\n");
+			return ret;
+		}
+		ret = phy_init(bp->sgmii_phy);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to init PS-GTR PHY: %d\n",
+				ret);
+			return ret;
+		}
+		ret = zynqmp_pm_is_function_supported(PM_IOCTL, IOCTL_SET_GEM_CONFIG);
+		if (!ret) {
+			u32 pm_info[2];
+
+			ret = of_property_read_u32_array(pdev->dev.of_node, "power-domains",
+							 pm_info, ARRAY_SIZE(pm_info));
+			if (ret < 0) {
+				dev_err(&pdev->dev, "Failed to read power management information\n");
+				return ret;
+			}
+			ret = zynqmp_pm_set_gem_config(pm_info[1], GEM_CONFIG_FIXED, 0);
+			if (ret < 0)
+				return ret;
+
+			ret = zynqmp_pm_set_gem_config(pm_info[1], GEM_CONFIG_SGMII_MODE, 1);
+			if (ret < 0)
+				return ret;
+		}
+	}
+
+	/* Fully reset GEM controller at hardware level using zynqmp-reset driver,
+	 * if mapped in device tree.
+	 */
+	ret = device_reset_optional(&pdev->dev);
+	if (ret) {
+		dev_err_probe(&pdev->dev, ret, "failed to reset controller");
+		phy_exit(bp->sgmii_phy);
+		return ret;
+	}
+
+	ret = macb_init(pdev);
+	if (ret)
+		phy_exit(bp->sgmii_phy);
+
+	return ret;
+}
+
 static const struct macb_config zynqmp_config = {
 	.caps = MACB_CAPS_GIGABIT_MODE_AVAILABLE |
 			MACB_CAPS_JUMBO |
-			MACB_CAPS_GEM_HAS_PTP | MACB_CAPS_BD_RD_PREFETCH,
+			MACB_CAPS_GEM_HAS_PTP | MACB_CAPS_BD_RD_PREFETCH |
+		MACB_CAPS_PARTIAL_STORE_FORWARD | MACB_CAPS_WOL,
+	.dma_burst_length = 16,
+	.clk_init = macb_clk_init,
+	.init = zynqmp_init,
+	.jumbo_max_len = 10240,
+	.usrio = &macb_default_usrio,
+};
+
+static const struct macb_config versal_config = {
+	.caps = MACB_CAPS_GIGABIT_MODE_AVAILABLE | MACB_CAPS_JUMBO |
+		MACB_CAPS_GEM_HAS_PTP | MACB_CAPS_BD_RD_PREFETCH |
+		MACB_CAPS_PARTIAL_STORE_FORWARD |
+		MACB_CAPS_WOL | MACB_CAPS_NEED_TSUCLK | MACB_CAPS_QUEUE_DISABLE,
 	.dma_burst_length = 16,
 	.clk_init = macb_clk_init,
 	.init = macb_init,
@@ -4627,6 +4882,7 @@
 	{ .compatible = "cdns,zynqmp-gem", .data = &zynqmp_config},
 	{ .compatible = "cdns,zynq-gem", .data = &zynq_config },
 	{ .compatible = "sifive,fu540-c000-gem", .data = &fu540_c000_config },
+	{ .compatible = "cdns,versal-gem", .data = &versal_config},
 	{ .compatible = "microchip,sama7g5-gem", .data = &sama7g5_gem_config },
 	{ .compatible = "microchip,sama7g5-emac", .data = &sama7g5_emac_config },
 	{ /* sentinel */ }
@@ -4715,31 +4971,25 @@
 	}
 	bp->num_queues = num_queues;
 	bp->queue_mask = queue_mask;
-	if (macb_config)
-		bp->dma_burst_length = macb_config->dma_burst_length;
+	bp->dma_burst_length = macb_config->dma_burst_length;
 	bp->pclk = pclk;
 	bp->hclk = hclk;
 	bp->tx_clk = tx_clk;
 	bp->rx_clk = rx_clk;
 	bp->tsu_clk = tsu_clk;
-	if (macb_config)
-		bp->jumbo_max_len = macb_config->jumbo_max_len;
-
-	bp->wol = 0;
-	if (of_get_property(np, "magic-packet", NULL))
-		bp->wol |= MACB_WOL_HAS_MAGIC_PACKET;
-	device_set_wakeup_capable(&pdev->dev, bp->wol & MACB_WOL_HAS_MAGIC_PACKET);
+	bp->jumbo_max_len = macb_config->jumbo_max_len;
 
 	bp->usrio = macb_config->usrio;
 
 	spin_lock_init(&bp->lock);
+	spin_lock_init(&bp->stats_lock);
 
 	/* setup capabilities */
 	macb_configure_caps(bp, macb_config);
 
 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
 	if (GEM_BFEXT(DAW64, gem_readl(bp, DCFG6))) {
-		dma_set_mask(&pdev->dev, DMA_BIT_MASK(44));
+		dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(44));
 		bp->hw_dma_cap |= HW_DMA_CAP_64B;
 	}
 #endif
@@ -4774,7 +5024,7 @@
 	if (bp->caps & MACB_CAPS_NEEDS_RSTONUBR)
 		bp->rx_intr_mask |= MACB_BIT(RXUBR);
 
-	err = of_get_mac_address(np, bp->dev->dev_addr);
+	err = of_get_ethdev_address(np, bp->dev);
 	if (err == -EPROBE_DEFER)
 		goto err_out_free_netdev;
 	else if (err)
@@ -4791,21 +5041,23 @@
 	err = init(pdev);
 	if (err)
 		goto err_out_free_netdev;
+	err = register_netdev(dev);
+	if (err) {
+		dev_err(&pdev->dev, "Cannot register net device, aborting.\n");
+		goto err_out_free_netdev;
+	}
 
 	err = macb_mii_init(bp);
 	if (err)
-		goto err_out_free_netdev;
+		goto err_out_phy_exit;
 
 	netif_carrier_off(dev);
 
-	err = register_netdev(dev);
-	if (err) {
-		dev_err(&pdev->dev, "Cannot register net device, aborting.\n");
-		goto err_out_unregister_mdio;
-	}
-
 	tasklet_setup(&bp->hresp_err_tasklet, macb_hresp_error_task);
 
+	if (bp->caps & MACB_CAPS_WOL)
+		device_set_wakeup_capable(&bp->dev->dev, 1);
+
 	netdev_info(dev, "Cadence %s rev 0x%08x at 0x%08lx irq %d (%pM)\n",
 		    macb_is_gem(bp) ? "GEM" : "MACB", macb_readl(bp, MID),
 		    dev->base_addr, dev->irq, dev->dev_addr);
@@ -4815,9 +5067,9 @@
 
 	return 0;
 
-err_out_unregister_mdio:
-	mdiobus_unregister(bp->mii_bus);
-	mdiobus_free(bp->mii_bus);
+err_out_phy_exit:
+	phy_exit(bp->sgmii_phy);
+	unregister_netdev(dev);
 
 err_out_free_netdev:
 	free_netdev(dev);
@@ -4840,6 +5092,7 @@
 
 	if (dev) {
 		bp = netdev_priv(dev);
+		phy_exit(bp->sgmii_phy);
 		mdiobus_unregister(bp->mii_bus);
 		mdiobus_free(bp->mii_bus);
 
@@ -4866,55 +5119,55 @@
 	struct macb_queue *queue;
 	unsigned long flags;
 	unsigned int q;
-	int err;
+	u32 ctrl, arpipmask;
+
+	if (!device_may_wakeup(&bp->dev->dev))
+		phy_exit(bp->sgmii_phy);
 
 	if (!netif_running(netdev))
 		return 0;
 
-	if (bp->wol & MACB_WOL_ENABLED) {
+	if (device_may_wakeup(&bp->dev->dev)) {
+		if (!bp->dev->ip_ptr->ifa_list) {
+			netdev_err(netdev, "IP address not assigned\n");
+			return -EOPNOTSUPP;
+		}
 		spin_lock_irqsave(&bp->lock, flags);
-		/* Flush all status bits */
-		macb_writel(bp, TSR, -1);
-		macb_writel(bp, RSR, -1);
+		ctrl = macb_readl(bp, NCR);
+		ctrl &= ~(MACB_BIT(TE) | MACB_BIT(RE));
+		macb_writel(bp, NCR, ctrl);
+		/* Tie off RX queues */
 		for (q = 0, queue = bp->queues; q < bp->num_queues;
 		     ++q, ++queue) {
-			/* Disable all interrupts */
-			queue_writel(queue, IDR, -1);
-			queue_readl(queue, ISR);
-			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
-				queue_writel(queue, ISR, -1);
+			if (bp->caps & MACB_CAPS_QUEUE_DISABLE)
+				queue_writel(queue, RBQP, GEM_RBQP_DISABLE);
+			else
+				queue_writel(queue, RBQP,
+					     lower_32_bits(bp->rx_ring_tieoff_dma));
 		}
-		/* Change interrupt handler and
-		 * Enable WoL IRQ on queue 0
-		 */
-		devm_free_irq(dev, bp->queues[0].irq, bp->queues);
-		if (macb_is_gem(bp)) {
-			err = devm_request_irq(dev, bp->queues[0].irq, gem_wol_interrupt,
-					       IRQF_SHARED, netdev->name, bp->queues);
-			if (err) {
-				dev_err(dev,
-					"Unable to request IRQ %d (error %d)\n",
-					bp->queues[0].irq, err);
-				spin_unlock_irqrestore(&bp->lock, flags);
-				return err;
-			}
-			queue_writel(bp->queues, IER, GEM_BIT(WOL));
-			gem_writel(bp, WOL, MACB_BIT(MAG));
-		} else {
-			err = devm_request_irq(dev, bp->queues[0].irq, macb_wol_interrupt,
-					       IRQF_SHARED, netdev->name, bp->queues);
-			if (err) {
-				dev_err(dev,
-					"Unable to request IRQ %d (error %d)\n",
-					bp->queues[0].irq, err);
-				spin_unlock_irqrestore(&bp->lock, flags);
-				return err;
-			}
-			queue_writel(bp->queues, IER, MACB_BIT(WOL));
-			macb_writel(bp, WOL, MACB_BIT(MAG));
+		ctrl = macb_readl(bp, NCR);
+		ctrl |= MACB_BIT(RE);
+		macb_writel(bp, NCR, ctrl);
+		gem_writel(bp, NCFGR, gem_readl(bp, NCFGR) & ~MACB_BIT(NBC));
+		macb_writel(bp, TSR, -1);
+		macb_writel(bp, RSR, -1);
+		macb_readl(bp, ISR);
+		if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+			macb_writel(bp, ISR, -1);
+
+		/* Enable WOL (Q0 only) and disable all other interrupts */
+		macb_writel(bp, IER, MACB_BIT(WOL));
+		for (q = 1, queue = bp->queues; q < bp->num_queues;
+		     ++q, ++queue) {
+			queue_writel(queue, IDR, bp->rx_intr_mask |
+						 MACB_TX_INT_FLAGS |
+						 MACB_BIT(HRESP));
 		}
-		spin_unlock_irqrestore(&bp->lock, flags);
 
+		arpipmask = cpu_to_be32p(&bp->dev->ip_ptr->ifa_list->ifa_local)
+					 & 0xFFFF;
+		gem_writel(bp, WOL, MACB_BIT(ARP) | arpipmask);
+		spin_unlock_irqrestore(&bp->lock, flags);
 		enable_irq_wake(bp->queues[0].irq);
 	}
 
@@ -4923,7 +5176,7 @@
 	     ++q, ++queue)
 		napi_disable(&queue->napi);
 
-	if (!(bp->wol & MACB_WOL_ENABLED)) {
+	if (!device_may_wakeup(&bp->dev->dev)) {
 		rtnl_lock();
 		phylink_stop(bp->phylink);
 		rtnl_unlock();
@@ -4940,7 +5193,7 @@
 
 	if (bp->ptp_info)
 		bp->ptp_info->ptp_remove(netdev);
-	if (!device_may_wakeup(dev))
+	if (!device_may_wakeup(&bp->dev->dev))
 		pm_runtime_force_suspend(dev);
 
 	return 0;
@@ -4953,43 +5206,25 @@
 	struct macb_queue *queue;
 	unsigned long flags;
 	unsigned int q;
-	int err;
+
+	if (!device_may_wakeup(&bp->dev->dev))
+		phy_init(bp->sgmii_phy);
 
 	if (!netif_running(netdev))
 		return 0;
 
-	if (!device_may_wakeup(dev))
+	if (!device_may_wakeup(&bp->dev->dev))
 		pm_runtime_force_resume(dev);
 
-	if (bp->wol & MACB_WOL_ENABLED) {
+	if (device_may_wakeup(&bp->dev->dev)) {
 		spin_lock_irqsave(&bp->lock, flags);
-		/* Disable WoL */
-		if (macb_is_gem(bp)) {
-			queue_writel(bp->queues, IDR, GEM_BIT(WOL));
-			gem_writel(bp, WOL, 0);
-		} else {
-			queue_writel(bp->queues, IDR, MACB_BIT(WOL));
-			macb_writel(bp, WOL, 0);
-		}
-		/* Clear ISR on queue 0 */
-		queue_readl(bp->queues, ISR);
+		macb_writel(bp, IDR, MACB_BIT(WOL));
+		gem_writel(bp, WOL, 0);
+		/* Clear Q0 ISR as WOL was enabled on Q0 */
 		if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
-			queue_writel(bp->queues, ISR, -1);
-		/* Replace interrupt handler on queue 0 */
-		devm_free_irq(dev, bp->queues[0].irq, bp->queues);
-		err = devm_request_irq(dev, bp->queues[0].irq, macb_interrupt,
-				       IRQF_SHARED, netdev->name, bp->queues);
-		if (err) {
-			dev_err(dev,
-				"Unable to request IRQ %d (error %d)\n",
-				bp->queues[0].irq, err);
-			spin_unlock_irqrestore(&bp->lock, flags);
-			return err;
-		}
-		spin_unlock_irqrestore(&bp->lock, flags);
-
+			macb_writel(bp, ISR, -1);
 		disable_irq_wake(bp->queues[0].irq);
-
+		spin_unlock_irqrestore(&bp->lock, flags);
 		/* Now make sure we disable phy before moving
 		 * to common restore path
 		 */
@@ -5013,6 +5248,7 @@
 	macb_set_rx_mode(netdev);
 	macb_restore_features(bp);
 	rtnl_lock();
+
 	phylink_start(bp->phylink);
 	rtnl_unlock();
 
@@ -5028,9 +5264,9 @@
 	struct net_device *netdev = dev_get_drvdata(dev);
 	struct macb *bp = netdev_priv(netdev);
 
-	if (!(device_may_wakeup(dev)))
+	if (!(device_may_wakeup(&bp->dev->dev)))
 		macb_clks_disable(bp->pclk, bp->hclk, bp->tx_clk, bp->rx_clk, bp->tsu_clk);
-	else
+	else if (!(bp->caps & MACB_CAPS_NEED_TSUCLK))
 		macb_clks_disable(NULL, NULL, NULL, NULL, bp->tsu_clk);
 
 	return 0;
@@ -5041,13 +5277,15 @@
 	struct net_device *netdev = dev_get_drvdata(dev);
 	struct macb *bp = netdev_priv(netdev);
 
-	if (!(device_may_wakeup(dev))) {
+	if (!(device_may_wakeup(&bp->dev->dev))) {
 		clk_prepare_enable(bp->pclk);
 		clk_prepare_enable(bp->hclk);
 		clk_prepare_enable(bp->tx_clk);
 		clk_prepare_enable(bp->rx_clk);
+		clk_prepare_enable(bp->tsu_clk);
+	} else if (!(bp->caps & MACB_CAPS_NEED_TSUCLK)) {
+		clk_prepare_enable(bp->tsu_clk);
 	}
-	clk_prepare_enable(bp->tsu_clk);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cadence/macb_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cadence/macb_ptp.c
@@ -242,6 +242,7 @@
 			    u32 dma_desc_ts_2, struct timespec64 *ts)
 {
 	struct timespec64 tsu;
+	bool sec_rollover = false;
 
 	ts->tv_sec = (GEM_BFEXT(DMA_SECH, dma_desc_ts_2) << GEM_DMA_SECL_SIZE) |
 			GEM_BFEXT(DMA_SECL, dma_desc_ts_1);
@@ -259,9 +260,12 @@
 	 */
 	if ((ts->tv_sec & (GEM_DMA_SEC_TOP >> 1)) &&
 	    !(tsu.tv_sec & (GEM_DMA_SEC_TOP >> 1)))
-		ts->tv_sec -= GEM_DMA_SEC_TOP;
+		sec_rollover = true;
+
+	ts->tv_sec |= ((~GEM_DMA_SEC_MASK) & tsu.tv_sec);
 
-	ts->tv_sec += ((~GEM_DMA_SEC_MASK) & tsu.tv_sec);
+	if (sec_rollover)
+		ts->tv_sec -= GEM_DMA_SEC_TOP;
 
 	return 0;
 }
@@ -394,11 +398,14 @@
 void gem_ptp_remove(struct net_device *ndev)
 {
 	struct macb *bp = netdev_priv(ndev);
+	unsigned long flags;
 
 	if (bp->ptp_clock)
 		ptp_clock_unregister(bp->ptp_clock);
 
+	spin_lock_irqsave(&bp->tsu_clk_lock, flags);
 	gem_ptp_clear_timer(bp);
+	spin_unlock_irqrestore(&bp->tsu_clk_lock, flags);
 
 	dev_info(&bp->pdev->dev, "%s ptp clock unregistered.\n",
 		 GEM_PTP_TIMER_NAME);
@@ -469,10 +476,12 @@
 	case HWTSTAMP_TX_ONESTEP_SYNC:
 		if (gem_ptp_set_one_step_sync(bp, 1) != 0)
 			return -ERANGE;
-		fallthrough;
-	case HWTSTAMP_TX_ON:
 		tx_bd_control = TSTAMP_ALL_FRAMES;
 		break;
+	case HWTSTAMP_TX_ON:
+		gem_ptp_set_one_step_sync(bp, 0);
+		tx_bd_control = TSTAMP_ALL_PTP_FRAMES;
+		break;
 	default:
 		return -ERANGE;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/calxeda/xgmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/calxeda/xgmac.c
@@ -607,7 +607,7 @@
 	writel(value, ioaddr + XGMAC_CONTROL);
 }
 
-static void xgmac_set_mac_addr(void __iomem *ioaddr, unsigned char *addr,
+static void xgmac_set_mac_addr(void __iomem *ioaddr, const unsigned char *addr,
 			       int num)
 {
 	u32 data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/liquidio/lio_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/liquidio/lio_core.c
@@ -411,7 +411,7 @@
 
 	if (!ether_addr_equal(netdev->dev_addr, mac)) {
 		macaddr_changed = true;
-		ether_addr_copy(netdev->dev_addr, mac);
+		eth_hw_addr_set(netdev, mac);
 		ether_addr_copy(((u8 *)&lio->linfo.hw_addr) + 2, mac);
 		call_netdevice_notifiers(NETDEV_CHANGEADDR, netdev);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/liquidio/lio_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/liquidio/lio_main.c
@@ -1798,13 +1798,10 @@
 
 	ifstate_set(lio, LIO_IFSTATE_RUNNING);
 
-	if (OCTEON_CN23XX_PF(oct)) {
-		if (!oct->msix_on)
-			if (setup_tx_poll_fn(netdev))
-				return -1;
-	} else {
-		if (setup_tx_poll_fn(netdev))
-			return -1;
+	if (!OCTEON_CN23XX_PF(oct) || !oct->msix_on) {
+		ret = setup_tx_poll_fn(netdev);
+		if (ret)
+			goto err_poll;
 	}
 
 	netif_tx_start_all_queues(netdev);
@@ -1817,7 +1814,7 @@
 	/* tell Octeon to start forwarding packets to host */
 	ret = send_rx_ctrl_cmd(lio, 1);
 	if (ret)
-		return ret;
+		goto err_rx_ctrl;
 
 	/* start periodical statistics fetch */
 	INIT_DELAYED_WORK(&lio->stats_wk.work, lio_fetch_stats);
@@ -1828,6 +1825,27 @@
 	dev_info(&oct->pci_dev->dev, "%s interface is opened\n",
 		 netdev->name);
 
+	return 0;
+
+err_rx_ctrl:
+	if (!OCTEON_CN23XX_PF(oct) || !oct->msix_on)
+		cleanup_tx_poll_fn(netdev);
+err_poll:
+	if (lio->ptp_clock) {
+		ptp_clock_unregister(lio->ptp_clock);
+		lio->ptp_clock = NULL;
+	}
+
+	if (oct->props[lio->ifidx].napi_enabled == 1) {
+		list_for_each_entry_safe(napi, n, &netdev->napi_list, dev_list)
+			napi_disable(napi);
+
+		oct->props[lio->ifidx].napi_enabled = 0;
+
+		if (OCTEON_CN23XX_PF(oct))
+			oct->droq[0]->ops.poll_mode = 0;
+	}
+
 	return ret;
 }
 
@@ -3632,7 +3650,7 @@
 
 		/* Copy MAC Address to OS network device structure */
 
-		ether_addr_copy(netdev->dev_addr, mac);
+		eth_hw_addr_set(netdev, mac);
 
 		/* By default all interfaces on a single Octeon uses the same
 		 * tx and rx queues
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/liquidio/lio_vf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/liquidio/lio_vf_main.c
@@ -2148,7 +2148,7 @@
 			mac[j] = *((u8 *)(((u8 *)&lio->linfo.hw_addr) + 2 + j));
 
 		/* Copy MAC Address to OS network device structure */
-		ether_addr_copy(netdev->dev_addr, mac);
+		eth_hw_addr_set(netdev, mac);
 
 		if (liquidio_setup_io_queues(octeon_dev, i,
 					     lio->linfo.num_txpciq,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c
@@ -272,13 +272,12 @@
 				pg_info->page_offset;
 			memcpy(skb->data, va, MIN_SKB_SIZE);
 			skb_put(skb, MIN_SKB_SIZE);
+			skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags,
+					pg_info->page,
+					pg_info->page_offset + MIN_SKB_SIZE,
+					len - MIN_SKB_SIZE,
+					LIO_RXBUFFER_SZ);
 		}
-
-		skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags,
-				pg_info->page,
-				pg_info->page_offset + MIN_SKB_SIZE,
-				len - MIN_SKB_SIZE,
-				LIO_RXBUFFER_SZ);
 	} else {
 		struct octeon_skb_page_info *pg_info =
 			((struct octeon_skb_page_info *)(skb->cb));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/octeon/octeon_mgmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/octeon/octeon_mgmt.c
@@ -1501,7 +1501,7 @@
 	netdev->min_mtu = 64 - OCTEON_MGMT_RX_HEADROOM;
 	netdev->max_mtu = 16383 - OCTEON_MGMT_RX_HEADROOM - VLAN_HLEN;
 
-	result = of_get_mac_address(pdev->dev.of_node, netdev->dev_addr);
+	result = of_get_ethdev_address(pdev->dev.of_node, netdev);
 	if (result)
 		eth_hw_addr_random(netdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/thunder/nicvf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/thunder/nicvf_main.c
@@ -221,8 +221,7 @@
 		nic->tns_mode = mbx.nic_cfg.tns_mode & 0x7F;
 		nic->node = mbx.nic_cfg.node_id;
 		if (!nic->set_mac_pending)
-			ether_addr_copy(nic->netdev->dev_addr,
-					mbx.nic_cfg.mac_addr);
+			eth_hw_addr_set(nic->netdev, mbx.nic_cfg.mac_addr);
 		nic->sqs_mode = mbx.nic_cfg.sqs_mode;
 		nic->loopback_supported = mbx.nic_cfg.loopback_supported;
 		nic->link_up = false;
@@ -2250,7 +2249,7 @@
 	err = register_netdev(netdev);
 	if (err) {
 		dev_err(dev, "Failed to register netdevice\n");
-		goto err_unregister_interrupts;
+		goto err_destroy_workqueue;
 	}
 
 	nic->msg_enable = debug;
@@ -2259,6 +2258,8 @@
 
 	return 0;
 
+err_destroy_workqueue:
+	destroy_workqueue(nic->nicvf_rx_mode_wq);
 err_unregister_interrupts:
 	nicvf_unregister_interrupts(nic);
 err_free_netdev:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cavium/thunder/thunder_bgx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cavium/thunder/thunder_bgx.c
@@ -1435,8 +1435,10 @@
 		return AE_OK;
 	}
 
-	if (strncmp(string.pointer, bgx_sel, 4))
+	if (strncmp(string.pointer, bgx_sel, 4)) {
+		kfree(string.pointer);
 		return AE_OK;
+	}
 
 	acpi_walk_namespace(ACPI_TYPE_DEVICE, handle, 1,
 			    bgx_acpi_register_phy, NULL, bgx, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb/gmac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb/gmac.h
@@ -117,7 +117,7 @@
 	const struct cmac_statistics *(*statistics_update)(struct cmac *, int);
 
 	int (*macaddress_get)(struct cmac *, u8 mac_addr[6]);
-	int (*macaddress_set)(struct cmac *, u8 mac_addr[6]);
+	int (*macaddress_set)(struct cmac *, const u8 mac_addr[6]);
 };
 
 typedef struct _cmac_instance cmac_instance;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb/pm3393.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb/pm3393.c
@@ -496,7 +496,7 @@
 	return 0;
 }
 
-static int pm3393_macaddress_set(struct cmac *cmac, u8 ma[6])
+static int pm3393_macaddress_set(struct cmac *cmac, const u8 ma[6])
 {
 	u32 val, lo, mid, hi, enabled = cmac->instance->enabled;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb/vsc7326.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb/vsc7326.c
@@ -379,7 +379,7 @@
 }
 
 /* Expect MAC address to be in network byte order. */
-static int mac_set_address(struct cmac* mac, u8 addr[6])
+static int mac_set_address(struct cmac* mac, const u8 addr[6])
 {
 	u32 val;
 	int port = mac->instance->index;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb3/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb3/common.h
@@ -710,7 +710,7 @@
 int t3_mac_disable(struct cmac *mac, int which);
 int t3_mac_set_mtu(struct cmac *mac, unsigned int mtu);
 int t3_mac_set_rx_mode(struct cmac *mac, struct net_device *dev);
-int t3_mac_set_address(struct cmac *mac, unsigned int idx, u8 addr[6]);
+int t3_mac_set_address(struct cmac *mac, unsigned int idx, const u8 addr[6]);
 int t3_mac_set_num_ucast(struct cmac *mac, int n);
 const struct mac_stats *t3_mac_update_stats(struct cmac *mac);
 int t3_mac_set_speed_duplex_fc(struct cmac *mac, int speed, int duplex, int fc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c
@@ -1302,6 +1302,7 @@
 		if (ret < 0) {
 			CH_ERR(adap, "failed to bind qsets, err %d\n", ret);
 			t3_intr_disable(adap);
+			quiesce_rx(adap);
 			free_irq_resources(adap);
 			err = ret;
 			goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb3/t3_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb3/t3_hw.c
@@ -3678,6 +3678,8 @@
 	    MAC_STATS_ACCUM_SECS : (MAC_STATS_ACCUM_SECS * 10);
 	adapter->params.pci.vpd_cap_addr =
 	    pci_find_capability(adapter->pdev, PCI_CAP_ID_VPD);
+	if (!adapter->params.pci.vpd_cap_addr)
+		return -ENODEV;
 	ret = get_vpd_params(adapter, &adapter->params.vpd);
 	if (ret < 0)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb3/xgmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb3/xgmac.c
@@ -240,7 +240,7 @@
 }
 
 /* Set one of the station's unicast MAC addresses. */
-int t3_mac_set_address(struct cmac *mac, unsigned int idx, u8 addr[6])
+int t3_mac_set_address(struct cmac *mac, unsigned int idx, const u8 addr[6])
 {
 	if (idx >= mac->nucast)
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/cudbg_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/cudbg_lib.c
@@ -14,6 +14,7 @@
 #include "cudbg_entity.h"
 #include "cudbg_lib.h"
 #include "cudbg_zlib.h"
+#include "cxgb4_tc_mqprio.h"
 
 static const u32 t6_tp_pio_array[][IREG_NUM_ELEM] = {
 	{0x7e40, 0x7e44, 0x020, 28}, /* t6_tp_pio_regs_20_to_3b */
@@ -3458,7 +3459,7 @@
 			for (i = 0; i < utxq->ntxq; i++)
 				QDESC_GET_TXQ(&utxq->uldtxq[i].q,
 					      cudbg_uld_txq_to_qtype(j),
-					      out_unlock);
+					      out_unlock_uld);
 		}
 	}
 
@@ -3475,7 +3476,7 @@
 			for (i = 0; i < urxq->nrxq; i++)
 				QDESC_GET_RXQ(&urxq->uldrxq[i].rspq,
 					      cudbg_uld_rxq_to_qtype(j),
-					      out_unlock);
+					      out_unlock_uld);
 		}
 
 		/* ULD FLQ */
@@ -3487,7 +3488,7 @@
 			for (i = 0; i < urxq->nrxq; i++)
 				QDESC_GET_FLQ(&urxq->uldrxq[i].fl,
 					      cudbg_uld_flq_to_qtype(j),
-					      out_unlock);
+					      out_unlock_uld);
 		}
 
 		/* ULD CIQ */
@@ -3500,29 +3501,34 @@
 			for (i = 0; i < urxq->nciq; i++)
 				QDESC_GET_RXQ(&urxq->uldrxq[base + i].rspq,
 					      cudbg_uld_ciq_to_qtype(j),
-					      out_unlock);
+					      out_unlock_uld);
 		}
 	}
+	mutex_unlock(&uld_mutex);
+
+	if (!padap->tc_mqprio)
+		goto out;
 
+	mutex_lock(&padap->tc_mqprio->mqprio_mutex);
 	/* ETHOFLD TXQ */
 	if (s->eohw_txq)
 		for (i = 0; i < s->eoqsets; i++)
 			QDESC_GET_TXQ(&s->eohw_txq[i].q,
-				      CUDBG_QTYPE_ETHOFLD_TXQ, out);
+				      CUDBG_QTYPE_ETHOFLD_TXQ, out_unlock_mqprio);
 
 	/* ETHOFLD RXQ and FLQ */
 	if (s->eohw_rxq) {
 		for (i = 0; i < s->eoqsets; i++)
 			QDESC_GET_RXQ(&s->eohw_rxq[i].rspq,
-				      CUDBG_QTYPE_ETHOFLD_RXQ, out);
+				      CUDBG_QTYPE_ETHOFLD_RXQ, out_unlock_mqprio);
 
 		for (i = 0; i < s->eoqsets; i++)
 			QDESC_GET_FLQ(&s->eohw_rxq[i].fl,
-				      CUDBG_QTYPE_ETHOFLD_FLQ, out);
+				      CUDBG_QTYPE_ETHOFLD_FLQ, out_unlock_mqprio);
 	}
 
-out_unlock:
-	mutex_unlock(&uld_mutex);
+out_unlock_mqprio:
+	mutex_unlock(&padap->tc_mqprio->mqprio_mutex);
 
 out:
 	qdesc_info->qdesc_entry_size = sizeof(*qdesc_entry);
@@ -3559,6 +3565,10 @@
 #undef QDESC_GET
 
 	return rc;
+
+out_unlock_uld:
+	mutex_unlock(&uld_mutex);
+	goto out;
 }
 
 int cudbg_collect_flash(struct cudbg_init *pdbg_init,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h
@@ -2084,7 +2084,7 @@
 		     struct sge_idma_monitor_state *idma,
 		     int hz, int ticks);
 int t4_set_vf_mac_acl(struct adapter *adapter, unsigned int vf,
-		      unsigned int naddr, u8 *addr);
+		      u8 start, unsigned int naddr, u8 *addr);
 void t4_tp_pio_read(struct adapter *adap, u32 *buff, u32 nregs,
 		    u32 start_index, bool sleep_ok);
 void t4_tp_tm_pio_read(struct adapter *adap, u32 *buff, u32 nregs,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c
@@ -2015,12 +2015,15 @@
 		if (ret)
 			return ret;
 
-		if (!sff8472_comp || (sff_diag_type & 4)) {
+		if (!sff8472_comp || (sff_diag_type & SFP_DIAG_ADDRMODE)) {
 			modinfo->type = ETH_MODULE_SFF_8079;
 			modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
 		} else {
 			modinfo->type = ETH_MODULE_SFF_8472;
-			modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
+			if (sff_diag_type & SFP_DIAG_IMPLEMENTED)
+				modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
+			else
+				modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN / 2;
 		}
 		break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c
@@ -1244,7 +1244,8 @@
 	 * in the Compressed Filter Tuple.
 	 */
 	if (tp->vlan_shift >= 0 && fs->mask.ivlan)
-		ntuple |= (FT_VLAN_VLD_F | fs->val.ivlan) << tp->vlan_shift;
+		ntuple |= (u64)(FT_VLAN_VLD_F |
+				fs->val.ivlan) << tp->vlan_shift;
 
 	if (tp->port_shift >= 0 && fs->mask.iport)
 		ntuple |= (u64)fs->val.iport << tp->port_shift;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c
@@ -1800,7 +1800,10 @@
 	struct adapter *adap = container_of(t, struct adapter, tids);
 	struct sk_buff *skb;
 
-	WARN_ON(tid_out_of_range(&adap->tids, tid));
+	if (tid_out_of_range(&adap->tids, tid)) {
+		dev_err(adap->pdev_dev, "tid %d out of range\n", tid);
+		return;
+	}
 
 	if (t->tid_tab[tid - adap->tids.tid_base]) {
 		t->tid_tab[tid - adap->tids.tid_base] = NULL;
@@ -3247,7 +3250,7 @@
 
 	dev_info(pi->adapter->pdev_dev,
 		 "Setting MAC %pM on VF %d\n", mac, vf);
-	ret = t4_set_vf_mac_acl(adap, vf + 1, 1, mac);
+	ret = t4_set_vf_mac_acl(adap, vf + 1, pi->lport, 1, mac);
 	if (!ret)
 		ether_addr_copy(adap->vfinfo[vf].vf_mac_addr, mac);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/sge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/sge.c
@@ -2682,12 +2682,12 @@
 	lb->loopback = 1;
 
 	q = &adap->sge.ethtxq[pi->first_qset];
-	__netif_tx_lock(q->txq, smp_processor_id());
+	__netif_tx_lock_bh(q->txq);
 
 	reclaim_completed_tx(adap, &q->q, -1, true);
 	credits = txq_avail(&q->q) - ndesc;
 	if (unlikely(credits < 0)) {
-		__netif_tx_unlock(q->txq);
+		__netif_tx_unlock_bh(q->txq);
 		return -ENOMEM;
 	}
 
@@ -2722,7 +2722,7 @@
 	init_completion(&lb->completion);
 	txq_advance(&q->q, ndesc);
 	cxgb4_ring_tx_db(adap, &q->q, ndesc);
-	__netif_tx_unlock(q->txq);
+	__netif_tx_unlock_bh(q->txq);
 
 	/* wait for the pkt to return */
 	ret = wait_for_completion_timeout(&lb->completion, 10 * HZ);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c
@@ -2793,14 +2793,14 @@
 		goto out;
 	na = ret;
 
-	memcpy(p->id, vpd + id, min_t(int, id_len, ID_LEN));
+	memcpy(p->id, vpd + id, min_t(unsigned int, id_len, ID_LEN));
 	strim(p->id);
-	memcpy(p->sn, vpd + sn, min_t(int, sn_len, SERNUM_LEN));
+	memcpy(p->sn, vpd + sn, min_t(unsigned int, sn_len, SERNUM_LEN));
 	strim(p->sn);
-	memcpy(p->pn, vpd + pn, min_t(int, pn_len, PN_LEN));
+	memcpy(p->pn, vpd + pn, min_t(unsigned int, pn_len, PN_LEN));
 	strim(p->pn);
-	memcpy(p->na, vpd + na, min_t(int, na_len, MACADDR_LEN));
-	strim((char *)p->na);
+	memcpy(p->na, vpd + na, min_t(unsigned int, na_len, MACADDR_LEN));
+	strim(p->na);
 
 out:
 	vfree(vpd);
@@ -3816,6 +3816,8 @@
 		 FW_PARAMS_PARAM_Z_V(FW_PARAMS_PARAM_DEV_PHYFW_DOWNLOAD));
 	ret = t4_set_params_timeout(adap, adap->mbox, adap->pf, 0, 1,
 				    &param, &val, 30000);
+	if (ret)
+		return ret;
 
 	/* If we have version number support, then check to see that the new
 	 * firmware got loaded properly.
@@ -10213,11 +10215,12 @@
  *	t4_set_vf_mac_acl - Set MAC address for the specified VF
  *	@adapter: The adapter
  *	@vf: one of the VFs instantiated by the specified PF
+ *	@start: The start port id associated with specified VF
  *	@naddr: the number of MAC addresses
  *	@addr: the MAC address(es) to be set to the specified VF
  */
 int t4_set_vf_mac_acl(struct adapter *adapter, unsigned int vf,
-		      unsigned int naddr, u8 *addr)
+		      u8 start, unsigned int naddr, u8 *addr)
 {
 	struct fw_acl_mac_cmd cmd;
 
@@ -10232,7 +10235,7 @@
 	cmd.en_to_len16 = cpu_to_be32((unsigned int)FW_LEN16(cmd));
 	cmd.nmac = naddr;
 
-	switch (adapter->pf) {
+	switch (start) {
 	case 3:
 		memcpy(cmd.macaddr3, addr, sizeof(cmd.macaddr3));
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4/t4_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4/t4_hw.h
@@ -293,6 +293,8 @@
 #define I2C_PAGE_SIZE		0x100
 #define SFP_DIAG_TYPE_ADDR	0x5c
 #define SFP_DIAG_TYPE_LEN	0x1
+#define SFP_DIAG_ADDRMODE	BIT(2)
+#define SFP_DIAG_IMPLEMENTED	BIT(6)
 #define SFF_8472_COMP_ADDR	0x5e
 #define SFF_8472_COMP_LEN	0x1
 #define SFF_REV_ADDR		0x1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c
@@ -858,7 +858,7 @@
 	 */
 	err = t4vf_update_port_info(pi);
 	if (err < 0)
-		return err;
+		goto err_unwind;
 
 	/*
 	 * Note that this interface is up and start everything up ...
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_cm.c
@@ -870,7 +870,7 @@
 		 * created only after 3 way handshake is done.
 		 */
 		sock_orphan(child);
-		percpu_counter_inc((child)->sk_prot->orphan_count);
+		INC_ORPHAN_COUNT(child);
 		chtls_release_resources(child);
 		chtls_conn_done(child);
 	} else {
@@ -1236,8 +1236,8 @@
 	csk->sndbuf = newsk->sk_sndbuf;
 	csk->smac_idx = ((struct port_info *)netdev_priv(ndev))->smt_idx;
 	RCV_WSCALE(tp) = select_rcv_wscale(tcp_full_space(newsk),
-					   sock_net(newsk)->
-						ipv4.sysctl_tcp_window_scaling,
+					   READ_ONCE(sock_net(newsk)->
+						     ipv4.sysctl_tcp_window_scaling),
 					   tp->window_clamp);
 	neigh_release(n);
 	inet_inherit_port(&tcp_hashinfo, lsk, newsk);
@@ -1384,7 +1384,7 @@
 #endif
 	}
 	if (req->tcpopt.wsf <= 14 &&
-	    sock_net(sk)->ipv4.sysctl_tcp_window_scaling) {
+	    READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_window_scaling)) {
 		inet_rsk(oreq)->wscale_ok = 1;
 		inet_rsk(oreq)->snd_wscale = req->tcpopt.wsf;
 	}
@@ -1392,7 +1392,7 @@
 	th_ecn = tcph->ece && tcph->cwr;
 	if (th_ecn) {
 		ect = !INET_ECN_is_not_ect(ip_dsfield);
-		ecn_ok = sock_net(sk)->ipv4.sysctl_tcp_ecn;
+		ecn_ok = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_ecn);
 		if ((!ect && ecn_ok) || tcp_ca_needs_ecn(sk))
 			inet_rsk(oreq)->ecn_ok = 1;
 	}
@@ -2260,7 +2260,7 @@
 
 		if (tp->snd_una != snd_una) {
 			tp->snd_una = snd_una;
-			tp->rcv_tstamp = tcp_time_stamp(tp);
+			tp->rcv_tstamp = tcp_jiffies32;
 			if (tp->snd_una == tp->snd_nxt &&
 			    !csk_flag_nochk(csk, CSK_TX_FAILOVER))
 				csk_reset_flag(csk, CSK_TX_WAIT_IDLE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_cm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_cm.h
@@ -95,7 +95,7 @@
 #define WSCALE_OK(tp) ((tp)->rx_opt.wscale_ok)
 #define TSTAMP_OK(tp) ((tp)->rx_opt.tstamp_ok)
 #define SACK_OK(tp) ((tp)->rx_opt.sack_ok)
-#define INC_ORPHAN_COUNT(sk) percpu_counter_inc((sk)->sk_prot->orphan_count)
+#define INC_ORPHAN_COUNT(sk) this_cpu_inc(*(sk)->sk_prot->orphan_count)
 
 /* TLS SKB */
 #define skb_ulp_tls_inline(skb)      (ULP_SKB_CB(skb)->ulp.tls.ofld)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c
@@ -346,8 +346,9 @@
 	 * driver. Once driver synthesizes cpl_pass_accpet_req the skb will go
 	 * through the regular cpl_pass_accept_req processing in TOM.
 	 */
-	skb = alloc_skb(gl->tot_len + sizeof(struct cpl_pass_accept_req)
-			- pktshift, GFP_ATOMIC);
+	skb = alloc_skb(size_add(gl->tot_len,
+				 sizeof(struct cpl_pass_accept_req)) -
+			pktshift, GFP_ATOMIC);
 	if (unlikely(!skb))
 		return NULL;
 	__skb_put(skb, gl->tot_len + sizeof(struct cpl_pass_accept_req)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/chelsio/libcxgb/libcxgb_cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/chelsio/libcxgb/libcxgb_cm.c
@@ -32,6 +32,7 @@
 
 #include <linux/tcp.h>
 #include <linux/ipv6.h>
+#include <net/inet_ecn.h>
 #include <net/route.h>
 #include <net/ip6_route.h>
 
@@ -99,7 +100,7 @@
 
 	rt = ip_route_output_ports(&init_net, &fl4, NULL, peer_ip, local_ip,
 				   peer_port, local_port, IPPROTO_TCP,
-				   tos, 0);
+				   tos & ~INET_ECN_MASK, 0);
 	if (IS_ERR(rt))
 		return NULL;
 	n = dst_neigh_lookup(&rt->dst, &peer_ip);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cisco/enic/enic_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cisco/enic/enic_main.c
@@ -1117,18 +1117,30 @@
 	pp->request = nla_get_u8(port[IFLA_PORT_REQUEST]);
 
 	if (port[IFLA_PORT_PROFILE]) {
+		if (nla_len(port[IFLA_PORT_PROFILE]) != PORT_PROFILE_MAX) {
+			memcpy(pp, &prev_pp, sizeof(*pp));
+			return -EINVAL;
+		}
 		pp->set |= ENIC_SET_NAME;
 		memcpy(pp->name, nla_data(port[IFLA_PORT_PROFILE]),
 			PORT_PROFILE_MAX);
 	}
 
 	if (port[IFLA_PORT_INSTANCE_UUID]) {
+		if (nla_len(port[IFLA_PORT_INSTANCE_UUID]) != PORT_UUID_MAX) {
+			memcpy(pp, &prev_pp, sizeof(*pp));
+			return -EINVAL;
+		}
 		pp->set |= ENIC_SET_INSTANCE;
 		memcpy(pp->instance_uuid,
 			nla_data(port[IFLA_PORT_INSTANCE_UUID]), PORT_UUID_MAX);
 	}
 
 	if (port[IFLA_PORT_HOST_UUID]) {
+		if (nla_len(port[IFLA_PORT_HOST_UUID]) != PORT_UUID_MAX) {
+			memcpy(pp, &prev_pp, sizeof(*pp));
+			return -EINVAL;
+		}
 		pp->set |= ENIC_SET_HOST;
 		memcpy(pp->host_uuid,
 			nla_data(port[IFLA_PORT_HOST_UUID]), PORT_UUID_MAX);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cisco/enic/enic_pp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cisco/enic/enic_pp.c
@@ -73,9 +73,9 @@
 	struct vic_provinfo *vp;
 	const u8 oui[3] = VIC_PROVINFO_CISCO_OUI;
 	const __be16 os_type = htons(VIC_GENERIC_PROV_OS_TYPE_LINUX);
+	const u8 *client_mac;
 	char uuid_str[38];
 	char client_mac_str[18];
-	u8 *client_mac;
 	int err;
 
 	ENIC_PP_BY_INDEX(enic, vf, pp, &err);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cortina/gemini.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cortina/gemini.c
@@ -68,7 +68,6 @@
 #define DEFAULT_GMAC_RXQ_ORDER		9
 #define DEFAULT_GMAC_TXQ_ORDER		8
 #define DEFAULT_RX_BUF_ORDER		11
-#define DEFAULT_NAPI_WEIGHT		64
 #define TX_MAX_FRAGS			16
 #define TX_QUEUE_NUM			1	/* max: 6 */
 #define RX_MAX_ALLOC_ORDER		2
@@ -80,8 +79,7 @@
 #define GMAC0_IRQ4_8 (GMAC0_MIB_INT_BIT | GMAC0_RX_OVERRUN_INT_BIT)
 
 #define GMAC_OFFLOAD_FEATURES (NETIF_F_SG | NETIF_F_IP_CSUM | \
-		NETIF_F_IPV6_CSUM | NETIF_F_RXCSUM | \
-		NETIF_F_TSO | NETIF_F_TSO_ECN | NETIF_F_TSO6)
+			       NETIF_F_IPV6_CSUM | NETIF_F_RXCSUM)
 
 /**
  * struct gmac_queue_page - page buffer per-page info
@@ -305,21 +303,21 @@
 	switch (phydev->speed) {
 	case 1000:
 		status.bits.speed = GMAC_SPEED_1000;
-		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+		if (phy_interface_mode_is_rgmii(phydev->interface))
 			status.bits.mii_rmii = GMAC_PHY_RGMII_1000;
 		netdev_dbg(netdev, "connect %s to RGMII @ 1Gbit\n",
 			   phydev_name(phydev));
 		break;
 	case 100:
 		status.bits.speed = GMAC_SPEED_100;
-		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+		if (phy_interface_mode_is_rgmii(phydev->interface))
 			status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
 		netdev_dbg(netdev, "connect %s to RGMII @ 100 Mbit\n",
 			   phydev_name(phydev));
 		break;
 	case 10:
 		status.bits.speed = GMAC_SPEED_10;
-		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+		if (phy_interface_mode_is_rgmii(phydev->interface))
 			status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
 		netdev_dbg(netdev, "connect %s to RGMII @ 10 Mbit\n",
 			   phydev_name(phydev));
@@ -389,6 +387,9 @@
 		status.bits.mii_rmii = GMAC_PHY_GMII;
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
 		netdev_dbg(netdev,
 			   "RGMII: set GMAC0 and GMAC1 to MII/RGMII mode\n");
 		status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
@@ -430,8 +431,8 @@
 		.val = CONFIG0_MAXLEN_1536,
 	},
 	{
-		.max_l3_len = 1542,
-		.val = CONFIG0_MAXLEN_1542,
+		.max_l3_len = 1548,
+		.val = CONFIG0_MAXLEN_1548,
 	},
 	{
 		.max_l3_len = 9212,
@@ -1106,10 +1107,13 @@
 {
 	struct gemini_ethernet_port *port = netdev_priv(netdev);
 	struct gemini_ethernet *geth = port->geth;
+	unsigned long flags;
 	u32 val, mask;
 
 	netdev_dbg(netdev, "%s device %d\n", __func__, netdev->dev_id);
 
+	spin_lock_irqsave(&geth->irq_lock, flags);
+
 	mask = GMAC0_IRQ0_TXQ0_INTS << (6 * netdev->dev_id + txq);
 
 	if (en)
@@ -1118,6 +1122,8 @@
 	val = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
 	val = en ? val | mask : val & ~mask;
 	writel(val, geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
+
+	spin_unlock_irqrestore(&geth->irq_lock, flags);
 }
 
 static void gmac_tx_irq(struct net_device *netdev, unsigned int txq_num)
@@ -1141,25 +1147,37 @@
 	struct gmac_txdesc *txd;
 	skb_frag_t *skb_frag;
 	dma_addr_t mapping;
-	unsigned short mtu;
 	void *buffer;
+	int ret;
 
-	mtu  = ETH_HLEN;
-	mtu += netdev->mtu;
-	if (skb->protocol == htons(ETH_P_8021Q))
-		mtu += VLAN_HLEN;
-
+	/* TODO: implement proper TSO using MTU in word3 */
 	word1 = skb->len;
 	word3 = SOF_BIT;
 
-	if (word1 > mtu) {
-		word1 |= TSS_MTU_ENABLE_BIT;
-		word3 |= mtu;
-	}
-
-	if (skb->ip_summed != CHECKSUM_NONE) {
+	if (skb->len >= ETH_FRAME_LEN) {
+		/* Hardware offloaded checksumming isn't working on frames
+		 * bigger than 1514 bytes. A hypothesis about this is that the
+		 * checksum buffer is only 1518 bytes, so when the frames get
+		 * bigger they get truncated, or the last few bytes get
+		 * overwritten by the FCS.
+		 *
+		 * Just use software checksumming and bypass on bigger frames.
+		 */
+		if (skb->ip_summed == CHECKSUM_PARTIAL) {
+			ret = skb_checksum_help(skb);
+			if (ret)
+				return ret;
+		}
+		word1 |= TSS_BYPASS_BIT;
+	} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
 		int tcp = 0;
 
+		/* We do not switch off the checksumming on non TCP/UDP
+		 * frames: as is shown from tests, the checksumming engine
+		 * is smart enough to see that a frame is not actually TCP
+		 * or UDP and then just pass it through without any changes
+		 * to the frame.
+		 */
 		if (skb->protocol == htons(ETH_P_IP)) {
 			word1 |= TSS_IP_CHKSUM_BIT;
 			tcp = ip_hdr(skb)->protocol == IPPROTO_TCP;
@@ -1402,15 +1420,19 @@
 	union gmac_rxdesc_3 word3;
 	struct page *page = NULL;
 	unsigned int page_offs;
+	unsigned long flags;
 	unsigned short r, w;
 	union dma_rwptr rw;
 	dma_addr_t mapping;
 	int frag_nr = 0;
 
+	spin_lock_irqsave(&geth->irq_lock, flags);
 	rw.bits32 = readl(ptr_reg);
 	/* Reset interrupt as all packages until here are taken into account */
 	writel(DEFAULT_Q0_INT_BIT << netdev->dev_id,
 	       geth->base + GLOBAL_INTERRUPT_STATUS_1_REG);
+	spin_unlock_irqrestore(&geth->irq_lock, flags);
+
 	r = rw.bits.rptr;
 	w = rw.bits.wptr;
 
@@ -1713,10 +1735,9 @@
 		gmac_update_hw_stats(netdev);
 
 	if (val & (GMAC0_RX_OVERRUN_INT_BIT << (netdev->dev_id * 8))) {
+		spin_lock(&geth->irq_lock);
 		writel(GMAC0_RXDERR_INT_BIT << (netdev->dev_id * 8),
 		       geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
-
-		spin_lock(&geth->irq_lock);
 		u64_stats_update_begin(&port->ir_stats_syncp);
 		++port->stats.rx_fifo_errors;
 		u64_stats_update_end(&port->ir_stats_syncp);
@@ -1917,7 +1938,7 @@
 
 	/* Racing with RX NAPI */
 	do {
-		start = u64_stats_fetch_begin(&port->rx_stats_syncp);
+		start = u64_stats_fetch_begin_irq(&port->rx_stats_syncp);
 
 		stats->rx_packets = port->stats.rx_packets;
 		stats->rx_bytes = port->stats.rx_bytes;
@@ -1929,11 +1950,11 @@
 		stats->rx_crc_errors = port->stats.rx_crc_errors;
 		stats->rx_frame_errors = port->stats.rx_frame_errors;
 
-	} while (u64_stats_fetch_retry(&port->rx_stats_syncp, start));
+	} while (u64_stats_fetch_retry_irq(&port->rx_stats_syncp, start));
 
 	/* Racing with MIB and TX completion interrupts */
 	do {
-		start = u64_stats_fetch_begin(&port->ir_stats_syncp);
+		start = u64_stats_fetch_begin_irq(&port->ir_stats_syncp);
 
 		stats->tx_errors = port->stats.tx_errors;
 		stats->tx_packets = port->stats.tx_packets;
@@ -1943,15 +1964,15 @@
 		stats->rx_missed_errors = port->stats.rx_missed_errors;
 		stats->rx_fifo_errors = port->stats.rx_fifo_errors;
 
-	} while (u64_stats_fetch_retry(&port->ir_stats_syncp, start));
+	} while (u64_stats_fetch_retry_irq(&port->ir_stats_syncp, start));
 
 	/* Racing with hard_start_xmit */
 	do {
-		start = u64_stats_fetch_begin(&port->tx_stats_syncp);
+		start = u64_stats_fetch_begin_irq(&port->tx_stats_syncp);
 
 		stats->tx_dropped = port->stats.tx_dropped;
 
-	} while (u64_stats_fetch_retry(&port->tx_stats_syncp, start));
+	} while (u64_stats_fetch_retry_irq(&port->tx_stats_syncp, start));
 
 	stats->rx_dropped += stats->rx_missed_errors;
 }
@@ -1976,15 +1997,6 @@
 	return 0;
 }
 
-static netdev_features_t gmac_fix_features(struct net_device *netdev,
-					   netdev_features_t features)
-{
-	if (netdev->mtu + ETH_HLEN + VLAN_HLEN > MTU_SIZE_BIT_MASK)
-		features &= ~GMAC_OFFLOAD_FEATURES;
-
-	return features;
-}
-
 static int gmac_set_features(struct net_device *netdev,
 			     netdev_features_t features)
 {
@@ -2029,18 +2041,18 @@
 	/* Racing with MIB interrupt */
 	do {
 		p = values;
-		start = u64_stats_fetch_begin(&port->ir_stats_syncp);
+		start = u64_stats_fetch_begin_irq(&port->ir_stats_syncp);
 
 		for (i = 0; i < RX_STATS_NUM; i++)
 			*p++ = port->hw_stats[i];
 
-	} while (u64_stats_fetch_retry(&port->ir_stats_syncp, start));
+	} while (u64_stats_fetch_retry_irq(&port->ir_stats_syncp, start));
 	values = p;
 
 	/* Racing with RX NAPI */
 	do {
 		p = values;
-		start = u64_stats_fetch_begin(&port->rx_stats_syncp);
+		start = u64_stats_fetch_begin_irq(&port->rx_stats_syncp);
 
 		for (i = 0; i < RX_STATUS_NUM; i++)
 			*p++ = port->rx_stats[i];
@@ -2048,13 +2060,13 @@
 			*p++ = port->rx_csum_stats[i];
 		*p++ = port->rx_napi_exits;
 
-	} while (u64_stats_fetch_retry(&port->rx_stats_syncp, start));
+	} while (u64_stats_fetch_retry_irq(&port->rx_stats_syncp, start));
 	values = p;
 
 	/* Racing with TX start_xmit */
 	do {
 		p = values;
-		start = u64_stats_fetch_begin(&port->tx_stats_syncp);
+		start = u64_stats_fetch_begin_irq(&port->tx_stats_syncp);
 
 		for (i = 0; i < TX_MAX_FRAGS; i++) {
 			*values++ = port->tx_frag_stats[i];
@@ -2063,7 +2075,7 @@
 		*values++ = port->tx_frags_linearized;
 		*values++ = port->tx_hw_csummed;
 
-	} while (u64_stats_fetch_retry(&port->tx_stats_syncp, start));
+	} while (u64_stats_fetch_retry_irq(&port->tx_stats_syncp, start));
 }
 
 static int gmac_get_ksettings(struct net_device *netdev,
@@ -2206,7 +2218,6 @@
 	.ndo_set_mac_address	= gmac_set_mac_address,
 	.ndo_get_stats64	= gmac_get_stats64,
 	.ndo_change_mtu		= gmac_change_mtu,
-	.ndo_fix_features	= gmac_fix_features,
 	.ndo_set_features	= gmac_set_features,
 };
 
@@ -2456,15 +2467,15 @@
 
 	netdev->hw_features = GMAC_OFFLOAD_FEATURES;
 	netdev->features |= GMAC_OFFLOAD_FEATURES | NETIF_F_GRO;
-	/* We can handle jumbo frames up to 10236 bytes so, let's accept
-	 * payloads of 10236 bytes minus VLAN and ethernet header
+	/* We can receive jumbo frames up to 10236 bytes but only
+	 * transmit 2047 bytes so, let's accept payloads of 2047
+	 * bytes minus VLAN and ethernet header
 	 */
 	netdev->min_mtu = ETH_MIN_MTU;
-	netdev->max_mtu = 10236 - VLAN_ETH_HLEN;
+	netdev->max_mtu = MTU_SIZE_BIT_MASK - VLAN_ETH_HLEN;
 
 	port->freeq_refill = 0;
-	netif_napi_add(netdev, &port->napi, gmac_napi_poll,
-		       DEFAULT_NAPI_WEIGHT);
+	netif_napi_add(netdev, &port->napi, gmac_napi_poll, NAPI_POLL_WEIGHT);
 
 	if (is_valid_ether_addr((void *)port->mac_addr)) {
 		memcpy(netdev->dev_addr, port->mac_addr, ETH_ALEN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/cortina/gemini.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/cortina/gemini.h
@@ -502,7 +502,7 @@
 #define SOF_BIT			0x80000000
 #define EOF_BIT			0x40000000
 #define EOFIE_BIT		BIT(29)
-#define MTU_SIZE_BIT_MASK	0x1fff
+#define MTU_SIZE_BIT_MASK	0x7ff /* Max MTU 2047 bytes */
 
 /* GMAC Tx Descriptor */
 struct gmac_txdesc {
@@ -787,7 +787,7 @@
 #define  CONFIG0_MAXLEN_1536	0
 #define  CONFIG0_MAXLEN_1518	1
 #define  CONFIG0_MAXLEN_1522	2
-#define  CONFIG0_MAXLEN_1542	3
+#define  CONFIG0_MAXLEN_1548	3
 #define  CONFIG0_MAXLEN_9k	4	/* 9212 */
 #define  CONFIG0_MAXLEN_10k	5	/* 10236 */
 #define  CONFIG0_MAXLEN_1518__6	6
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/davicom/dm9000.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/davicom/dm9000.c
@@ -1773,10 +1773,11 @@
 
 	unregister_netdev(ndev);
 	dm9000_release_board(pdev, dm);
-	free_netdev(ndev);		/* free device structure */
 	if (dm->power_supply)
 		regulator_disable(dm->power_supply);
 
+	free_netdev(ndev);		/* free device structure */
+
 	dev_dbg(&pdev->dev, "released and freed device\n");
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/dec/tulip/de4x5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/dec/tulip/de4x5.c
@@ -4708,6 +4708,10 @@
         lp->ibn = 3;
         lp->active = *p++;
 	if (MOTO_SROM_BUG) lp->active = 0;
+	/* if (MOTO_SROM_BUG) statement indicates lp->active could
+	 * be 8 (i.e. the size of array lp->phy) */
+	if (WARN_ON(lp->active >= ARRAY_SIZE(lp->phy)))
+		return -EINVAL;
 	lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
 	lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
 	lp->phy[lp->active].mc  = get_unaligned_le16(p); p += 2;
@@ -4999,19 +5003,23 @@
 	}
 	if ((j == limit) && (i < DE4X5_MAX_MII)) {
 	    for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++);
-	    lp->phy[k].addr = i;
-	    lp->phy[k].id = id;
-	    lp->phy[k].spd.reg = GENERIC_REG;      /* ANLPA register         */
-	    lp->phy[k].spd.mask = GENERIC_MASK;    /* 100Mb/s technologies   */
-	    lp->phy[k].spd.value = GENERIC_VALUE;  /* TX & T4, H/F Duplex    */
-	    lp->mii_cnt++;
-	    lp->active++;
-	    printk("%s: Using generic MII device control. If the board doesn't operate,\nplease mail the following dump to the author:\n", dev->name);
-	    j = de4x5_debug;
-	    de4x5_debug |= DEBUG_MII;
-	    de4x5_dbg_mii(dev, k);
-	    de4x5_debug = j;
-	    printk("\n");
+	    if (k < DE4X5_MAX_PHY) {
+		lp->phy[k].addr = i;
+		lp->phy[k].id = id;
+		lp->phy[k].spd.reg = GENERIC_REG;      /* ANLPA register         */
+		lp->phy[k].spd.mask = GENERIC_MASK;    /* 100Mb/s technologies   */
+		lp->phy[k].spd.value = GENERIC_VALUE;  /* TX & T4, H/F Duplex    */
+		lp->mii_cnt++;
+		lp->active++;
+		printk("%s: Using generic MII device control. If the board doesn't operate,\nplease mail the following dump to the author:\n", dev->name);
+		j = de4x5_debug;
+		de4x5_debug |= DEBUG_MII;
+		de4x5_dbg_mii(dev, k);
+		de4x5_debug = j;
+		printk("\n");
+	    } else {
+		goto purgatory;
+	    }
 	}
     }
   purgatory:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/dec/tulip/tulip_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/dec/tulip/tulip_core.c
@@ -1398,8 +1398,10 @@
 
 	/* alloc_etherdev ensures aligned and zeroed private structures */
 	dev = alloc_etherdev (sizeof (*tp));
-	if (!dev)
+	if (!dev) {
+		pci_disable_device(pdev);
 		return -ENOMEM;
+	}
 
 	SET_NETDEV_DEV(dev, &pdev->dev);
 	if (pci_resource_len (pdev, 0) < tulip_tbl[chip_idx].io_size) {
@@ -1778,6 +1780,7 @@
 
 err_out_free_netdev:
 	free_netdev (dev);
+	pci_disable_device(pdev);
 	return -ENODEV;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/dec/tulip/winbond-840.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/dec/tulip/winbond-840.c
@@ -877,7 +877,7 @@
 		8000	16 longwords		0200 2 longwords	2000 32 longwords
 		C000	32  longwords		0400 4 longwords */
 
-#if defined (__i386__) && !defined(MODULE)
+#if defined (__i386__) && !defined(MODULE) && !defined(CONFIG_UML)
 	/* When not a module we can work around broken '486 PCI boards. */
 	if (boot_cpu_data.x86 <= 4) {
 		i |= 0x4800;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/dlink/dl2k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/dlink/dl2k.c
@@ -567,7 +567,7 @@
 	 */
 	for (i = 0; i < 3; i++)
 		dw16(StationAddr0 + 2 * i,
-		     cpu_to_le16(((u16 *)dev->dev_addr)[i]));
+		     cpu_to_le16(((const u16 *)dev->dev_addr)[i]));
 
 	set_multicast (dev);
 	if (np->coalesce) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/dnet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/dnet.c
@@ -60,11 +60,11 @@
 {
 	u16 tmp;
 
-	tmp = be16_to_cpup((__be16 *)bp->dev->dev_addr);
+	tmp = be16_to_cpup((const __be16 *)bp->dev->dev_addr);
 	dnet_writew_mac(bp, DNET_INTERNAL_MAC_ADDR_0_REG, tmp);
-	tmp = be16_to_cpup((__be16 *)(bp->dev->dev_addr + 2));
+	tmp = be16_to_cpup((const __be16 *)(bp->dev->dev_addr + 2));
 	dnet_writew_mac(bp, DNET_INTERNAL_MAC_ADDR_1_REG, tmp);
-	tmp = be16_to_cpup((__be16 *)(bp->dev->dev_addr + 4));
+	tmp = be16_to_cpup((const __be16 *)(bp->dev->dev_addr + 4));
 	dnet_writew_mac(bp, DNET_INTERNAL_MAC_ADDR_2_REG, tmp);
 }
 
@@ -550,11 +550,11 @@
 
 	skb_tx_timestamp(skb);
 
+	spin_unlock_irqrestore(&bp->lock, flags);
+
 	/* free the buffer */
 	dev_kfree_skb(skb);
 
-	spin_unlock_irqrestore(&bp->lock, flags);
-
 	return NETDEV_TX_OK;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/emulex/benet/be.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/emulex/benet/be.h
@@ -563,7 +563,7 @@
 	struct be_dma_mem mbox_mem_alloced;
 
 	struct be_mcc_obj mcc_obj;
-	struct mutex mcc_lock;	/* For serializing mcc cmds to BE card */
+	spinlock_t mcc_lock;	/* For serializing mcc cmds to BE card */
 	spinlock_t mcc_cq_lock;
 
 	u16 cfg_num_rx_irqs;		/* configured via set-channels */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -573,7 +573,7 @@
 /* Wait till no more pending mcc requests are present */
 static int be_mcc_wait_compl(struct be_adapter *adapter)
 {
-#define mcc_timeout		12000 /* 12s timeout */
+#define mcc_timeout		120000 /* 12s timeout */
 	int i, status = 0;
 	struct be_mcc_obj *mcc_obj = &adapter->mcc_obj;
 
@@ -587,7 +587,7 @@
 
 		if (atomic_read(&mcc_obj->q.used) == 0)
 			break;
-		usleep_range(500, 1000);
+		udelay(100);
 	}
 	if (i == mcc_timeout) {
 		dev_err(&adapter->pdev->dev, "FW not responding\n");
@@ -865,7 +865,7 @@
 static int be_cmd_lock(struct be_adapter *adapter)
 {
 	if (use_mcc(adapter)) {
-		mutex_lock(&adapter->mcc_lock);
+		spin_lock_bh(&adapter->mcc_lock);
 		return 0;
 	} else {
 		return mutex_lock_interruptible(&adapter->mbox_lock);
@@ -876,7 +876,7 @@
 static void be_cmd_unlock(struct be_adapter *adapter)
 {
 	if (use_mcc(adapter))
-		return mutex_unlock(&adapter->mcc_lock);
+		return spin_unlock_bh(&adapter->mcc_lock);
 	else
 		return mutex_unlock(&adapter->mbox_lock);
 }
@@ -1046,7 +1046,7 @@
 	struct be_cmd_req_mac_query *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1075,19 +1075,19 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
 /* Uses synchronous MCCQ */
-int be_cmd_pmac_add(struct be_adapter *adapter, u8 *mac_addr,
+int be_cmd_pmac_add(struct be_adapter *adapter, const u8 *mac_addr,
 		    u32 if_id, u32 *pmac_id, u32 domain)
 {
 	struct be_mcc_wrb *wrb;
 	struct be_cmd_req_pmac_add *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1112,7 +1112,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 
 	 if (base_status(status) == MCC_STATUS_UNAUTHORIZED_REQUEST)
 		status = -EPERM;
@@ -1130,7 +1130,7 @@
 	if (pmac_id == -1)
 		return 0;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1150,7 +1150,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1413,7 +1413,7 @@
 	struct be_dma_mem *q_mem = &rxq->dma_mem;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1443,7 +1443,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1507,7 +1507,7 @@
 	struct be_cmd_req_q_destroy *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1524,7 +1524,7 @@
 	q->created = false;
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1592,7 +1592,7 @@
 	struct be_cmd_req_hdr *hdr;
 	int status = 0;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1620,7 +1620,7 @@
 	adapter->stats_cmd_sent = true;
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1636,7 +1636,7 @@
 			    CMD_SUBSYSTEM_ETH))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1659,7 +1659,7 @@
 	adapter->stats_cmd_sent = true;
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1696,7 +1696,7 @@
 	struct be_cmd_req_link_status *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	if (link_status)
 		*link_status = LINK_DOWN;
@@ -1735,7 +1735,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1746,7 +1746,7 @@
 	struct be_cmd_req_get_cntl_addnl_attribs *req;
 	int status = 0;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1761,7 +1761,7 @@
 
 	status = be_mcc_notify(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1810,7 +1810,7 @@
 	if (!get_fat_cmd.va)
 		return -ENOMEM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	while (total_size) {
 		buf_size = min(total_size, (u32)60*1024);
@@ -1848,9 +1848,9 @@
 		log_offset += buf_size;
 	}
 err:
+	spin_unlock_bh(&adapter->mcc_lock);
 	dma_free_coherent(&adapter->pdev->dev, get_fat_cmd.size,
 			  get_fat_cmd.va, get_fat_cmd.dma);
-	mutex_unlock(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1861,7 +1861,7 @@
 	struct be_cmd_req_get_fw_version *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1884,7 +1884,7 @@
 			sizeof(adapter->fw_on_flash));
 	}
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1898,7 +1898,7 @@
 	struct be_cmd_req_modify_eq_delay *req;
 	int status = 0, i;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1921,7 +1921,7 @@
 
 	status = be_mcc_notify(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1948,7 +1948,7 @@
 	struct be_cmd_req_vlan_config *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -1970,7 +1970,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -1981,7 +1981,7 @@
 	struct be_cmd_req_rx_filter *req = mem->va;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2014,7 +2014,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2045,7 +2045,7 @@
 			    CMD_SUBSYSTEM_COMMON))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2065,7 +2065,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 
 	if (base_status(status) == MCC_STATUS_FEATURE_NOT_SUPPORTED)
 		return  -EOPNOTSUPP;
@@ -2084,7 +2084,7 @@
 			    CMD_SUBSYSTEM_COMMON))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2107,7 +2107,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2188,7 +2188,7 @@
 	if (!(be_if_cap_flags(adapter) & BE_IF_FLAGS_RSS))
 		return 0;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2213,7 +2213,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2225,7 +2225,7 @@
 	struct be_cmd_req_enable_disable_beacon *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2246,7 +2246,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2257,7 +2257,7 @@
 	struct be_cmd_req_get_beacon_state *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2281,13 +2281,13 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
 /* Uses sync mcc */
 int be_cmd_read_port_transceiver_data(struct be_adapter *adapter,
-				      u8 page_num, u8 *data)
+				      u8 page_num, u32 off, u32 len, u8 *data)
 {
 	struct be_dma_mem cmd;
 	struct be_mcc_wrb *wrb;
@@ -2305,7 +2305,7 @@
 		return -ENOMEM;
 	}
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2321,13 +2321,13 @@
 	req->port = cpu_to_le32(adapter->hba_port_num);
 	req->page_num = cpu_to_le32(page_num);
 	status = be_mcc_notify_wait(adapter);
-	if (!status) {
+	if (!status && len > 0) {
 		struct be_cmd_resp_port_type *resp = cmd.va;
 
-		memcpy(data, resp->page_data, PAGE_DATA_LEN);
+		memcpy(data, resp->page_data + off, len);
 	}
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	dma_free_coherent(&adapter->pdev->dev, cmd.size, cmd.va, cmd.dma);
 	return status;
 }
@@ -2344,7 +2344,7 @@
 	void *ctxt = NULL;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 	adapter->flash_status = 0;
 
 	wrb = wrb_from_mccq(adapter);
@@ -2386,7 +2386,7 @@
 	if (status)
 		goto err_unlock;
 
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 
 	if (!wait_for_completion_timeout(&adapter->et_cmd_compl,
 					 msecs_to_jiffies(60000)))
@@ -2405,7 +2405,7 @@
 	return status;
 
 err_unlock:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2415,7 +2415,7 @@
 	int status;
 
 	status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A0,
-						   page_data);
+						   0, PAGE_DATA_LEN, page_data);
 	if (!status) {
 		switch (adapter->phy.interface_type) {
 		case PHY_TYPE_QSFP:
@@ -2440,7 +2440,7 @@
 	int status;
 
 	status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A0,
-						   page_data);
+						   0, PAGE_DATA_LEN, page_data);
 	if (!status) {
 		strlcpy(adapter->phy.vendor_name, page_data +
 			SFP_VENDOR_NAME_OFFSET, SFP_VENDOR_NAME_LEN - 1);
@@ -2459,7 +2459,7 @@
 	struct be_mcc_wrb *wrb;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2477,7 +2477,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2490,7 +2490,7 @@
 	struct lancer_cmd_resp_read_object *resp;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2524,7 +2524,7 @@
 	}
 
 err_unlock:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2536,7 +2536,7 @@
 	struct be_cmd_write_flashrom *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 	adapter->flash_status = 0;
 
 	wrb = wrb_from_mccq(adapter);
@@ -2561,7 +2561,7 @@
 	if (status)
 		goto err_unlock;
 
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 
 	if (!wait_for_completion_timeout(&adapter->et_cmd_compl,
 					 msecs_to_jiffies(40000)))
@@ -2572,7 +2572,7 @@
 	return status;
 
 err_unlock:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -2583,7 +2583,7 @@
 	struct be_mcc_wrb *wrb;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -2610,7 +2610,7 @@
 		memcpy(flashed_crc, req->crc, 4);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3216,7 +3216,7 @@
 	struct be_cmd_req_acpi_wol_magic_config *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3233,7 +3233,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3248,7 +3248,7 @@
 			    CMD_SUBSYSTEM_LOWLEVEL))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3271,7 +3271,7 @@
 	if (status)
 		goto err_unlock;
 
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 
 	if (!wait_for_completion_timeout(&adapter->et_cmd_compl,
 					 msecs_to_jiffies(SET_LB_MODE_TIMEOUT)))
@@ -3280,7 +3280,7 @@
 	return status;
 
 err_unlock:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3297,7 +3297,7 @@
 			    CMD_SUBSYSTEM_LOWLEVEL))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3323,7 +3323,7 @@
 	if (status)
 		goto err;
 
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 
 	wait_for_completion(&adapter->et_cmd_compl);
 	resp = embedded_payload(wrb);
@@ -3331,7 +3331,7 @@
 
 	return status;
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3347,7 +3347,7 @@
 			    CMD_SUBSYSTEM_LOWLEVEL))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3381,7 +3381,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3392,7 +3392,7 @@
 	struct be_cmd_req_seeprom_read *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3408,7 +3408,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3423,7 +3423,7 @@
 			    CMD_SUBSYSTEM_COMMON))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3468,7 +3468,7 @@
 	}
 	dma_free_coherent(&adapter->pdev->dev, cmd.size, cmd.va, cmd.dma);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3478,7 +3478,7 @@
 	struct be_cmd_req_set_qos *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3498,7 +3498,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3610,7 +3610,7 @@
 	struct be_cmd_req_get_fn_privileges *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3642,7 +3642,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3654,7 +3654,7 @@
 	struct be_cmd_req_set_fn_privileges *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3674,7 +3674,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3706,7 +3706,7 @@
 		return -ENOMEM;
 	}
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3770,7 +3770,7 @@
 	}
 
 out:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	dma_free_coherent(&adapter->pdev->dev, get_mac_list_cmd.size,
 			  get_mac_list_cmd.va, get_mac_list_cmd.dma);
 	return status;
@@ -3830,7 +3830,7 @@
 	if (!cmd.va)
 		return -ENOMEM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3852,7 +3852,7 @@
 
 err:
 	dma_free_coherent(&adapter->pdev->dev, cmd.size, cmd.va, cmd.dma);
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3888,7 +3888,7 @@
 			    CMD_SUBSYSTEM_COMMON))
 		return -EPERM;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3929,7 +3929,7 @@
 	status = be_mcc_notify_wait(adapter);
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -3943,7 +3943,7 @@
 	int status;
 	u16 vid;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -3990,7 +3990,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -4189,7 +4189,7 @@
 	struct be_cmd_req_set_ext_fat_caps *req;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -4205,7 +4205,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -4683,7 +4683,7 @@
 	if (iface == 0xFFFFFFFF)
 		return -1;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -4700,7 +4700,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -4734,7 +4734,7 @@
 	struct be_cmd_resp_get_iface_list *resp;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -4755,7 +4755,7 @@
 	}
 
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -4849,7 +4849,7 @@
 	if (BEx_chip(adapter))
 		return 0;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -4867,7 +4867,7 @@
 	req->enable = 1;
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -4940,7 +4940,7 @@
 	u32 link_config = 0;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -4968,7 +4968,7 @@
 
 	status = be_mcc_notify_wait(adapter);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -4999,8 +4999,7 @@
 	struct be_mcc_wrb *wrb;
 	int status;
 
-	if (mutex_lock_interruptible(&adapter->mcc_lock))
-		return -1;
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -5038,7 +5037,7 @@
 		dev_info(&adapter->pdev->dev,
 			 "Adapter does not support HW error recovery\n");
 
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 
@@ -5052,7 +5051,7 @@
 	struct be_cmd_resp_hdr *resp;
 	int status;
 
-	mutex_lock(&adapter->mcc_lock);
+	spin_lock_bh(&adapter->mcc_lock);
 
 	wrb = wrb_from_mccq(adapter);
 	if (!wrb) {
@@ -5075,7 +5074,7 @@
 	memcpy(wrb_payload, resp, sizeof(*resp) + resp->response_length);
 	be_dws_le_to_cpu(wrb_payload, sizeof(*resp) + resp->response_length);
 err:
-	mutex_unlock(&adapter->mcc_lock);
+	spin_unlock_bh(&adapter->mcc_lock);
 	return status;
 }
 EXPORT_SYMBOL(be_roce_mcc_cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -2385,7 +2385,7 @@
 int be_fw_wait_ready(struct be_adapter *adapter);
 int be_cmd_mac_addr_query(struct be_adapter *adapter, u8 *mac_addr,
 			  bool permanent, u32 if_handle, u32 pmac_id);
-int be_cmd_pmac_add(struct be_adapter *adapter, u8 *mac_addr, u32 if_id,
+int be_cmd_pmac_add(struct be_adapter *adapter, const u8 *mac_addr, u32 if_id,
 		    u32 *pmac_id, u32 domain);
 int be_cmd_pmac_del(struct be_adapter *adapter, u32 if_id, int pmac_id,
 		    u32 domain);
@@ -2427,7 +2427,7 @@
 int be_cmd_get_beacon_state(struct be_adapter *adapter, u8 port_num,
 			    u32 *state);
 int be_cmd_read_port_transceiver_data(struct be_adapter *adapter,
-				      u8 page_num, u8 *data);
+				      u8 page_num, u32 off, u32 len, u8 *data);
 int be_cmd_query_cable_type(struct be_adapter *adapter);
 int be_cmd_query_sfp_info(struct be_adapter *adapter);
 int lancer_cmd_read_object(struct be_adapter *adapter, struct be_dma_mem *cmd,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/emulex/benet/be_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/emulex/benet/be_ethtool.c
@@ -1342,7 +1342,7 @@
 		return -EOPNOTSUPP;
 
 	status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A0,
-						   page_data);
+						   0, PAGE_DATA_LEN, page_data);
 	if (!status) {
 		if (!page_data[SFP_PLUS_SFF_8472_COMP]) {
 			modinfo->type = ETH_MODULE_SFF_8079;
@@ -1360,25 +1360,32 @@
 {
 	struct be_adapter *adapter = netdev_priv(netdev);
 	int status;
+	u32 begin, end;
 
 	if (!check_privilege(adapter, MAX_PRIVILEGES))
 		return -EOPNOTSUPP;
 
-	status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A0,
-						   data);
-	if (status)
-		goto err;
-
-	if (eeprom->offset + eeprom->len > PAGE_DATA_LEN) {
-		status = be_cmd_read_port_transceiver_data(adapter,
-							   TR_PAGE_A2,
-							   data +
-							   PAGE_DATA_LEN);
+	begin = eeprom->offset;
+	end = eeprom->offset + eeprom->len;
+
+	if (begin < PAGE_DATA_LEN) {
+		status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A0, begin,
+							   min_t(u32, end, PAGE_DATA_LEN) - begin,
+							   data);
+		if (status)
+			goto err;
+
+		data += PAGE_DATA_LEN - begin;
+		begin = PAGE_DATA_LEN;
+	}
+
+	if (end > PAGE_DATA_LEN) {
+		status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A2,
+							   begin - PAGE_DATA_LEN,
+							   end - begin, data);
 		if (status)
 			goto err;
 	}
-	if (eeprom->offset)
-		memcpy(data, data + eeprom->offset, eeprom->len);
 err:
 	return be_cmd_status(status);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/emulex/benet/be_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/emulex/benet/be_main.c
@@ -272,7 +272,7 @@
 	iowrite32(val, adapter->db + DB_CQ_OFFSET);
 }
 
-static int be_dev_mac_add(struct be_adapter *adapter, u8 *mac)
+static int be_dev_mac_add(struct be_adapter *adapter, const u8 *mac)
 {
 	int i;
 
@@ -369,7 +369,7 @@
 	/* Remember currently programmed MAC */
 	ether_addr_copy(adapter->dev_mac, addr->sa_data);
 done:
-	ether_addr_copy(netdev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(netdev, addr->sa_data);
 	dev_info(dev, "MAC address changed to %pM\n", addr->sa_data);
 	return 0;
 err:
@@ -1125,7 +1125,7 @@
 						  struct be_wrb_params
 						  *wrb_params)
 {
-	struct vlan_ethhdr *veh = (struct vlan_ethhdr *)skb->data;
+	struct vlan_ethhdr *veh = skb_vlan_eth_hdr(skb);
 	unsigned int eth_hdr_len;
 	struct iphdr *ip;
 
@@ -1136,10 +1136,11 @@
 	eth_hdr_len = ntohs(skb->protocol) == ETH_P_8021Q ?
 						VLAN_ETH_HLEN : ETH_HLEN;
 	if (skb->len <= 60 &&
-	    (lancer_chip(adapter) || skb_vlan_tag_present(skb)) &&
-	    is_ipv4_pkt(skb)) {
+	    (lancer_chip(adapter) || BE3_chip(adapter) ||
+	     skb_vlan_tag_present(skb)) && is_ipv4_pkt(skb)) {
 		ip = (struct iphdr *)ip_hdr(skb);
-		pskb_trim(skb, eth_hdr_len + ntohs(ip->tot_len));
+		if (unlikely(pskb_trim(skb, eth_hdr_len + ntohs(ip->tot_len))))
+			goto tx_drop;
 	}
 
 	/* If vlan tag is already inlined in the packet, skip HW VLAN
@@ -1381,10 +1382,8 @@
 	be_get_wrb_params_from_skb(adapter, skb, &wrb_params);
 
 	wrb_cnt = be_xmit_enqueue(adapter, txo, skb, &wrb_params);
-	if (unlikely(!wrb_cnt)) {
-		dev_kfree_skb_any(skb);
-		goto drop;
-	}
+	if (unlikely(!wrb_cnt))
+		goto drop_skb;
 
 	/* if os2bmc is enabled and if the pkt is destined to bmc,
 	 * enqueue the pkt a 2nd time with mgmt bit set.
@@ -1393,7 +1392,7 @@
 		BE_WRB_F_SET(wrb_params.features, OS2BMC, 1);
 		wrb_cnt = be_xmit_enqueue(adapter, txo, skb, &wrb_params);
 		if (unlikely(!wrb_cnt))
-			goto drop;
+			goto drop_skb;
 		else
 			skb_get(skb);
 	}
@@ -1407,6 +1406,8 @@
 		be_xmit_flush(adapter, txo);
 
 	return NETDEV_TX_OK;
+drop_skb:
+	dev_kfree_skb_any(skb);
 drop:
 	tx_stats(txo)->tx_drv_drops++;
 	/* Flush the already enqueued tx requests */
@@ -5672,8 +5673,8 @@
 	}
 
 	mutex_init(&adapter->mbox_lock);
-	mutex_init(&adapter->mcc_lock);
 	mutex_init(&adapter->rx_filter_lock);
+	spin_lock_init(&adapter->mcc_lock);
 	spin_lock_init(&adapter->mcc_cq_lock);
 	init_completion(&adapter->et_cmd_compl);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ethoc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ethoc.c
@@ -806,8 +806,8 @@
 
 static void ethoc_do_set_mac_address(struct net_device *dev)
 {
+	const unsigned char *mac = dev->dev_addr;
 	struct ethoc *priv = netdev_priv(dev);
-	unsigned char *mac = dev->dev_addr;
 
 	ethoc_write(priv, MAC_ADDR0, (mac[2] << 24) | (mac[3] << 16) |
 				     (mac[4] <<  8) | (mac[5] <<  0));
@@ -1148,10 +1148,10 @@
 
 	/* Allow the platform setup code to pass in a MAC address. */
 	if (pdata) {
-		ether_addr_copy(netdev->dev_addr, pdata->hwaddr);
+		eth_hw_addr_set(netdev, pdata->hwaddr);
 		priv->phy_id = pdata->phy_id;
 	} else {
-		of_get_mac_address(pdev->dev.of_node, netdev->dev_addr);
+		of_get_ethdev_address(pdev->dev.of_node, netdev);
 		priv->phy_id = -1;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ezchip/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ezchip/Kconfig
@@ -18,7 +18,7 @@
 
 config EZCHIP_NPS_MANAGEMENT_ENET
 	tristate "EZchip NPS management enet support"
-	depends on OF_IRQ && OF_NET
+	depends on OF_IRQ
 	depends on HAS_IOMEM
 	help
 	  Simple LAN device for debug or management purposes.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ezchip/nps_enet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ezchip/nps_enet.c
@@ -421,7 +421,7 @@
 
 	res = eth_mac_addr(ndev, p);
 	if (!res) {
-		ether_addr_copy(ndev->dev_addr, addr->sa_data);
+		eth_hw_addr_set(ndev, addr->sa_data);
 		nps_enet_set_hw_mac_address(ndev);
 	}
 
@@ -601,7 +601,7 @@
 	dev_dbg(dev, "Registers base address is 0x%p\n", priv->regs_base);
 
 	/* set kernel MAC address to dev */
-	err = of_get_mac_address(dev->of_node, ndev->dev_addr);
+	err = of_get_ethdev_address(dev->of_node, ndev);
 	if (err)
 		eth_hw_addr_random(ndev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/faraday/ftgmac100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/faraday/ftgmac100.c
@@ -186,7 +186,7 @@
 
 	addr = device_get_mac_address(priv->dev, mac, ETH_ALEN);
 	if (addr) {
-		ether_addr_copy(priv->netdev->dev_addr, mac);
+		eth_hw_addr_set(priv->netdev, mac);
 		dev_info(priv->dev, "Read MAC address %pM from device tree\n",
 			 mac);
 		return;
@@ -203,7 +203,7 @@
 	mac[5] = l & 0xff;
 
 	if (is_valid_ether_addr(mac)) {
-		ether_addr_copy(priv->netdev->dev_addr, mac);
+		eth_hw_addr_set(priv->netdev, mac);
 		dev_info(priv->dev, "Read MAC address %pM from chip\n", mac);
 	} else {
 		eth_hw_addr_random(priv->netdev);
@@ -569,7 +569,7 @@
 	(*processed)++;
 	return true;
 
- drop:
+drop:
 	/* Clean rxdes0 (which resets own bit) */
 	rxdes->rxdes0 = cpu_to_le32(status & priv->rxdes0_edorr_mask);
 	priv->rx_pointer = ftgmac100_next_rx_pointer(priv, pointer);
@@ -653,6 +653,11 @@
 	ftgmac100_free_tx_packet(priv, pointer, skb, txdes, ctl_stat);
 	txdes->txdes0 = cpu_to_le32(ctl_stat & priv->txdes0_edotr_mask);
 
+	/* Ensure the descriptor config is visible before setting the tx
+	 * pointer.
+	 */
+	smp_wmb();
+
 	priv->tx_clean_pointer = ftgmac100_next_tx_pointer(priv, pointer);
 
 	return true;
@@ -806,6 +811,11 @@
 	dma_wmb();
 	first->txdes0 = cpu_to_le32(f_ctl_stat);
 
+	/* Ensure the descriptor config is visible before setting the tx
+	 * pointer.
+	 */
+	smp_wmb();
+
 	/* Update next TX pointer */
 	priv->tx_pointer = pointer;
 
@@ -826,7 +836,7 @@
 
 	return NETDEV_TX_OK;
 
- dma_err:
+dma_err:
 	if (net_ratelimit())
 		netdev_err(netdev, "map tx fragment failed\n");
 
@@ -848,7 +858,7 @@
 	 * last fragment, so we know ftgmac100_free_tx_packet()
 	 * hasn't freed the skb yet.
 	 */
- drop:
+drop:
 	/* Drop the packet */
 	dev_kfree_skb_any(skb);
 	netdev->stats.tx_dropped++;
@@ -1448,7 +1458,7 @@
 	ftgmac100_init_all(priv, true);
 
 	netdev_dbg(netdev, "Reset done !\n");
- bail:
+bail:
 	if (priv->mii_bus)
 		mutex_unlock(&priv->mii_bus->mdio_lock);
 	if (netdev->phydev)
@@ -1519,15 +1529,15 @@
 
 	return 0;
 
- err_ncsi:
+err_ncsi:
 	napi_disable(&priv->napi);
 	netif_stop_queue(netdev);
- err_alloc:
+err_alloc:
 	ftgmac100_free_buffers(priv);
 	free_irq(netdev->irq, netdev);
- err_irq:
+err_irq:
 	netif_napi_del(&priv->napi);
- err_hw:
+err_hw:
 	iowrite32(0, priv->base + FTGMAC100_OFFSET_IER);
 	ftgmac100_free_rings(priv);
 	return err;
@@ -1746,6 +1756,19 @@
 	return rc;
 }
 
+static bool ftgmac100_has_child_node(struct device_node *np, const char *name)
+{
+	struct device_node *child_np = of_get_child_by_name(np, name);
+	bool ret = false;
+
+	if (child_np) {
+		ret = true;
+		of_node_put(child_np);
+	}
+
+	return ret;
+}
+
 static int ftgmac100_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -1817,11 +1840,6 @@
 		priv->rxdes0_edorr_mask = BIT(30);
 		priv->txdes0_edotr_mask = BIT(30);
 		priv->is_aspeed = true;
-		/* Disable ast2600 problematic HW arbitration */
-		if (of_device_is_compatible(np, "aspeed,ast2600-mac")) {
-			iowrite32(FTGMAC100_TM_DEFAULT,
-				  priv->base + FTGMAC100_OFFSET_TM);
-		}
 	} else {
 		priv->rxdes0_edorr_mask = BIT(15);
 		priv->txdes0_edotr_mask = BIT(15);
@@ -1870,7 +1888,7 @@
 
 		/* Display what we found */
 		phy_attached_info(phy);
-	} else if (np && !of_get_child_by_name(np, "mdio")) {
+	} else if (np && !ftgmac100_has_child_node(np, "mdio")) {
 		/* Support legacy ASPEED devicetree descriptions that decribe a
 		 * MAC with an embedded MDIO controller but have no "mdio"
 		 * child node. Automatically scan the MDIO bus for available
@@ -1893,6 +1911,11 @@
 		err = ftgmac100_setup_clk(priv);
 		if (err)
 			goto err_phy_connect;
+
+		/* Disable ast2600 problematic HW arbitration */
+		if (of_device_is_compatible(np, "aspeed,ast2600-mac"))
+			iowrite32(FTGMAC100_TM_DEFAULT,
+				  priv->base + FTGMAC100_OFFSET_TM);
 	}
 
 	/* Default ring sizes */
@@ -1910,6 +1933,11 @@
 	/* AST2400  doesn't have working HW checksum generation */
 	if (np && (of_device_is_compatible(np, "aspeed,ast2400-mac")))
 		netdev->hw_features &= ~NETIF_F_HW_CSUM;
+
+	/* AST2600 tx checksum with NCSI is broken */
+	if (priv->use_ncsi && of_device_is_compatible(np, "aspeed,ast2600-mac"))
+		netdev->hw_features &= ~NETIF_F_HW_CSUM;
+
 	if (np && of_get_property(np, "no-hw-checksum", NULL))
 		netdev->hw_features &= ~(NETIF_F_HW_CSUM | NETIF_F_RXCSUM);
 	netdev->features |= netdev->hw_features;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/faraday/ftgmac100.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/faraday/ftgmac100.h
@@ -84,7 +84,7 @@
 			    FTGMAC100_INT_RPKT_BUF)
 
 /* All the interrupts we care about */
-#define FTGMAC100_INT_ALL (FTGMAC100_INT_RPKT_BUF  |  \
+#define FTGMAC100_INT_ALL (FTGMAC100_INT_RXTX  |  \
 			   FTGMAC100_INT_BAD)
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/fealnx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/fealnx.c
@@ -827,7 +827,7 @@
 		return -EAGAIN;
 
 	for (i = 0; i < 3; i++)
-		iowrite16(((unsigned short*)dev->dev_addr)[i],
+		iowrite16(((const unsigned short *)dev->dev_addr)[i],
 				ioaddr + PAR0 + i*2);
 
 	init_ring(dev);
@@ -857,7 +857,7 @@
 	np->bcrvalue |= 0x04;	/* big-endian */
 #endif
 
-#if defined(__i386__) && !defined(MODULE)
+#if defined(__i386__) && !defined(MODULE) && !defined(CONFIG_UML)
 	if (boot_cpu_data.x86 <= 4)
 		np->crvalue = 0xa00;
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
@@ -272,7 +272,7 @@
 	} else {
 		eth_hw_addr_random(net_dev);
 		err = priv->mac_dev->change_addr(priv->mac_dev->fman_mac,
-			(enet_addr_t *)net_dev->dev_addr);
+			(const enet_addr_t *)net_dev->dev_addr);
 		if (err) {
 			dev_err(dev, "Failed to set random MAC address\n");
 			return -EINVAL;
@@ -452,7 +452,7 @@
 	mac_dev = priv->mac_dev;
 
 	err = mac_dev->change_addr(mac_dev->fman_mac,
-				   (enet_addr_t *)net_dev->dev_addr);
+				   (const enet_addr_t *)net_dev->dev_addr);
 	if (err < 0) {
 		netif_err(priv, drv, net_dev, "mac_dev->change_addr() = %d\n",
 			  err);
@@ -910,14 +910,18 @@
 	}
 }
 
-static void dpaa_fq_setup(struct dpaa_priv *priv,
-			  const struct dpaa_fq_cbs *fq_cbs,
-			  struct fman_port *tx_port)
+static int dpaa_fq_setup(struct dpaa_priv *priv,
+			 const struct dpaa_fq_cbs *fq_cbs,
+			 struct fman_port *tx_port)
 {
 	int egress_cnt = 0, conf_cnt = 0, num_portals = 0, portal_cnt = 0, cpu;
 	const cpumask_t *affine_cpus = qman_affine_cpus();
-	u16 channels[NR_CPUS];
 	struct dpaa_fq *fq;
+	u16 *channels;
+
+	channels = kcalloc(num_possible_cpus(), sizeof(u16), GFP_KERNEL);
+	if (!channels)
+		return -ENOMEM;
 
 	for_each_cpu_and(cpu, affine_cpus, cpu_online_mask)
 		channels[num_portals++] = qman_affine_channel(cpu);
@@ -976,6 +980,10 @@
 				break;
 		}
 	}
+
+	kfree(channels);
+
+	return 0;
 }
 
 static inline int dpaa_tx_fq_to_id(const struct dpaa_priv *priv,
@@ -2261,12 +2269,12 @@
 dpaa_start_xmit(struct sk_buff *skb, struct net_device *net_dev)
 {
 	const int queue_mapping = skb_get_queue_mapping(skb);
-	bool nonlinear = skb_is_nonlinear(skb);
 	struct rtnl_link_stats64 *percpu_stats;
 	struct dpaa_percpu_priv *percpu_priv;
 	struct netdev_queue *txq;
 	struct dpaa_priv *priv;
 	struct qm_fd fd;
+	bool nonlinear;
 	int offset = 0;
 	int err = 0;
 
@@ -2276,6 +2284,13 @@
 
 	qm_fd_clear_fd(&fd);
 
+	/* Packet data is always read as 32-bit words, so zero out any part of
+	 * the skb which might be sent if we have to pad the packet
+	 */
+	if (__skb_put_padto(skb, ETH_ZLEN, false))
+		goto enomem;
+
+	nonlinear = skb_is_nonlinear(skb);
 	if (!nonlinear) {
 		/* We're going to store the skb backpointer at the beginning
 		 * of the data buffer, so we need a privately owned skb
@@ -2395,6 +2410,9 @@
 
 	cleaned = qman_p_poll_dqrr(np->p, budget);
 
+	if (np->xdp_act & XDP_REDIRECT)
+		xdp_do_flush();
+
 	if (cleaned < budget) {
 		napi_complete_done(napi, cleaned);
 		qman_p_irqsource_add(np->p, QM_PIRQ_DQRI);
@@ -2402,9 +2420,6 @@
 		qman_p_irqsource_add(np->p, QM_PIRQ_DQRI);
 	}
 
-	if (np->xdp_act & XDP_REDIRECT)
-		xdp_do_flush();
-
 	return cleaned;
 }
 
@@ -3444,7 +3459,9 @@
 	 */
 	dpaa_eth_add_channel(priv->channel, &pdev->dev);
 
-	dpaa_fq_setup(priv, &dpaa_fq_cbs, priv->mac_dev->port[TX]);
+	err = dpaa_fq_setup(priv, &dpaa_fq_cbs, priv->mac_dev->port[TX]);
+	if (err)
+		goto free_dpaa_bps;
 
 	/* Create a congestion group for this netdev, with
 	 * dynamically-allocated CGR ID.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c
@@ -489,11 +489,15 @@
 	info->phc_index = -1;
 
 	fman_node = of_get_parent(mac_node);
-	if (fman_node)
+	if (fman_node) {
 		ptp_node = of_parse_phandle(fman_node, "ptimer-handle", 0);
+		of_node_put(fman_node);
+	}
 
-	if (ptp_node)
+	if (ptp_node) {
 		ptp_dev = of_find_device_by_node(ptp_node);
+		of_node_put(ptp_node);
+	}
 
 	if (ptp_dev)
 		ptp = platform_get_drvdata(ptp_dev);
@@ -537,12 +541,16 @@
 			     struct netlink_ext_ack *extack)
 {
 	const cpumask_t *cpus = qman_affine_cpus();
-	bool needs_revert[NR_CPUS] = {false};
 	struct qman_portal *portal;
 	u32 period, prev_period;
 	u8 thresh, prev_thresh;
+	bool *needs_revert;
 	int cpu, res;
 
+	needs_revert = kcalloc(num_possible_cpus(), sizeof(bool), GFP_KERNEL);
+	if (!needs_revert)
+		return -ENOMEM;
+
 	period = c->rx_coalesce_usecs;
 	thresh = c->rx_max_coalesced_frames;
 
@@ -565,6 +573,8 @@
 		needs_revert[cpu] = true;
 	}
 
+	kfree(needs_revert);
+
 	return 0;
 
 revert_values:
@@ -578,6 +588,8 @@
 		qman_dqrr_set_ithresh(portal, prev_thresh);
 	}
 
+	kfree(needs_revert);
+
 	return res;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
@@ -952,14 +952,12 @@
 	dma_addr_t addr;
 
 	buffer_start = skb->data - dpaa2_eth_needed_headroom(skb);
-
-	/* If there's enough room to align the FD address, do it.
-	 * It will help hardware optimize accesses.
-	 */
 	aligned_start = PTR_ALIGN(buffer_start - DPAA2_ETH_TX_BUF_ALIGN,
 				  DPAA2_ETH_TX_BUF_ALIGN);
 	if (aligned_start >= skb->head)
 		buffer_start = aligned_start;
+	else
+		return -ENOMEM;
 
 	/* Store a backpointer to the skb at the beginning of the buffer
 	 * (in the private data area) such that we can release it
@@ -1389,8 +1387,8 @@
 		buf_array[i] = addr;
 
 		/* tracing point */
-		trace_dpaa2_eth_buf_seed(priv->net_dev,
-					 page, DPAA2_ETH_RX_BUF_RAW_SIZE,
+		trace_dpaa2_eth_buf_seed(priv->net_dev, page_address(page),
+					 DPAA2_ETH_RX_BUF_RAW_SIZE,
 					 addr, priv->rx_buf_size,
 					 bpid);
 	}
@@ -1597,10 +1595,15 @@
 		if (rx_cleaned >= budget ||
 		    txconf_cleaned >= DPAA2_ETH_TXCONF_PER_NAPI) {
 			work_done = budget;
+			if (ch->xdp.res & XDP_REDIRECT)
+				xdp_do_flush();
 			goto out;
 		}
 	} while (store_cleaned);
 
+	if (ch->xdp.res & XDP_REDIRECT)
+		xdp_do_flush();
+
 	/* We didn't consume the entire budget, so finish napi and
 	 * re-enable data availability notifications
 	 */
@@ -1625,9 +1628,7 @@
 		txc_fq->dq_bytes = 0;
 	}
 
-	if (ch->xdp.res & XDP_REDIRECT)
-		xdp_do_flush_map();
-	else if (rx_cleaned && ch->xdp.res & XDP_TX)
+	if (rx_cleaned && ch->xdp.res & XDP_TX)
 		dpaa2_eth_xdp_tx_flush(priv, ch, &priv->fq[flowid]);
 
 	return work_done;
@@ -2467,11 +2468,14 @@
 static int update_xps(struct dpaa2_eth_priv *priv)
 {
 	struct net_device *net_dev = priv->net_dev;
-	struct cpumask xps_mask;
-	struct dpaa2_eth_fq *fq;
 	int i, num_queues, netdev_queues;
+	struct dpaa2_eth_fq *fq;
+	cpumask_var_t xps_mask;
 	int err = 0;
 
+	if (!alloc_cpumask_var(&xps_mask, GFP_KERNEL))
+		return -ENOMEM;
+
 	num_queues = dpaa2_eth_queue_count(priv);
 	netdev_queues = (net_dev->num_tc ? : 1) * num_queues;
 
@@ -2481,16 +2485,17 @@
 	for (i = 0; i < netdev_queues; i++) {
 		fq = &priv->fq[i % num_queues];
 
-		cpumask_clear(&xps_mask);
-		cpumask_set_cpu(fq->target_cpu, &xps_mask);
+		cpumask_clear(xps_mask);
+		cpumask_set_cpu(fq->target_cpu, xps_mask);
 
-		err = netif_set_xps_queue(net_dev, &xps_mask, i);
+		err = netif_set_xps_queue(net_dev, xps_mask, i);
 		if (err) {
 			netdev_warn_once(net_dev, "Error setting XPS queue\n");
 			break;
 		}
 	}
 
+	free_cpumask_var(xps_mask);
 	return err;
 }
 
@@ -4329,7 +4334,7 @@
 	}
 
 	INIT_WORK(&priv->tx_onestep_tstamp, dpaa2_eth_tx_onestep_tstamp);
-
+	mutex_init(&priv->onestep_tstamp_lock);
 	skb_queue_head_init(&priv->tx_skbs);
 
 	priv->rx_copybreak = DPAA2_ETH_DEFAULT_COPYBREAK;
@@ -4443,6 +4448,8 @@
 	if (err)
 		goto err_dl_port_add;
 
+	net_dev->needed_headroom = DPAA2_ETH_SWA_SIZE + DPAA2_ETH_TX_BUF_ALIGN;
+
 	err = register_netdev(net_dev);
 	if (err < 0) {
 		dev_err(dev, "register_netdev() failed\n");
@@ -4511,12 +4518,12 @@
 #ifdef CONFIG_DEBUG_FS
 	dpaa2_dbg_remove(priv);
 #endif
+
+	unregister_netdev(net_dev);
 	rtnl_lock();
 	dpaa2_eth_disconnect_mac(priv);
 	rtnl_unlock();
 
-	unregister_netdev(net_dev);
-
 	dpaa2_eth_dl_port_del(priv);
 	dpaa2_eth_dl_traps_unregister(priv);
 	dpaa2_eth_dl_unregister(priv);
@@ -4538,10 +4545,12 @@
 
 	fsl_mc_portal_free(priv->mc_io);
 
-	free_netdev(net_dev);
+	destroy_workqueue(priv->dpaa2_ptp_wq);
 
 	dev_dbg(net_dev->dev.parent, "Removed interface %s\n", net_dev->name);
 
+	free_netdev(net_dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h
@@ -670,7 +670,7 @@
 
 static inline unsigned int dpaa2_eth_needed_headroom(struct sk_buff *skb)
 {
-	unsigned int headroom = DPAA2_ETH_SWA_SIZE;
+	unsigned int headroom = DPAA2_ETH_SWA_SIZE + DPAA2_ETH_TX_BUF_ALIGN;
 
 	/* If we don't have an skb (e.g. XDP buffer), we only need space for
 	 * the software annotation area
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
@@ -168,7 +168,7 @@
 	base = of_iomap(node, 0);
 	if (!base) {
 		err = -ENOMEM;
-		goto err_close;
+		goto err_put;
 	}
 
 	err = fsl_mc_allocate_irqs(mc_dev);
@@ -212,6 +212,8 @@
 	fsl_mc_free_irqs(mc_dev);
 err_unmap:
 	iounmap(base);
+err_put:
+	of_node_put(node);
 err_close:
 	dprtc_close(mc_dev->mc_io, 0, mc_dev->mc_handle);
 err_free_mcp:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa2/dpaa2-switch-flower.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa2/dpaa2-switch-flower.c
@@ -132,16 +132,19 @@
 						 DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, acl_entry_cfg->key_iova))) {
 		dev_err(dev, "DMA mapping failed\n");
+		kfree(cmd_buff);
 		return -EFAULT;
 	}
 
 	err = dpsw_acl_add_entry(ethsw->mc_io, 0, ethsw->dpsw_handle,
 				 filter_block->acl_id, acl_entry_cfg);
 
-	dma_unmap_single(dev, acl_entry_cfg->key_iova, sizeof(cmd_buff),
+	dma_unmap_single(dev, acl_entry_cfg->key_iova,
+			 DPAA2_ETHSW_PORT_ACL_CMD_BUF_SIZE,
 			 DMA_TO_DEVICE);
 	if (err) {
 		dev_err(dev, "dpsw_acl_add_entry() failed %d\n", err);
+		kfree(cmd_buff);
 		return err;
 	}
 
@@ -172,16 +175,18 @@
 						 DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev, acl_entry_cfg->key_iova))) {
 		dev_err(dev, "DMA mapping failed\n");
+		kfree(cmd_buff);
 		return -EFAULT;
 	}
 
 	err = dpsw_acl_remove_entry(ethsw->mc_io, 0, ethsw->dpsw_handle,
 				    block->acl_id, acl_entry_cfg);
 
-	dma_unmap_single(dev, acl_entry_cfg->key_iova, sizeof(cmd_buff),
-			 DMA_TO_DEVICE);
+	dma_unmap_single(dev, acl_entry_cfg->key_iova,
+			 DPAA2_ETHSW_PORT_ACL_CMD_BUF_SIZE, DMA_TO_DEVICE);
 	if (err) {
 		dev_err(dev, "dpsw_acl_remove_entry() failed %d\n", err);
+		kfree(cmd_buff);
 		return err;
 	}
 
@@ -532,6 +537,7 @@
 	struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
 	struct flow_dissector *dissector = rule->match.dissector;
 	struct netlink_ext_ack *extack = cls->common.extack;
+	int ret = -EOPNOTSUPP;
 
 	if (dissector->used_keys &
 	    ~(BIT(FLOW_DISSECTOR_KEY_BASIC) |
@@ -561,9 +567,10 @@
 		}
 
 		*vlan = (u16)match.key->vlan_id;
+		ret = 0;
 	}
 
-	return 0;
+	return ret;
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/dpaa2/dpaa2-switch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/dpaa2/dpaa2-switch.c
@@ -2585,13 +2585,14 @@
 
 static int dpaa2_switch_seed_bp(struct ethsw_core *ethsw)
 {
-	int *count, i;
+	int *count, ret, i;
 
 	for (i = 0; i < DPAA2_ETHSW_NUM_BUFS; i += BUFS_PER_CMD) {
+		ret = dpaa2_switch_add_bufs(ethsw, ethsw->bpid);
 		count = &ethsw->buf_count;
-		*count += dpaa2_switch_add_bufs(ethsw, ethsw->bpid);
+		*count += ret;
 
-		if (unlikely(*count < BUFS_PER_CMD))
+		if (unlikely(ret < BUFS_PER_CMD))
 			return -ENOMEM;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/Makefile
@@ -9,7 +9,6 @@
 
 obj-$(CONFIG_FSL_ENETC_VF) += fsl-enetc-vf.o
 fsl-enetc-vf-y := enetc_vf.o $(common-objs)
-fsl-enetc-vf-$(CONFIG_FSL_ENETC_QOS) += enetc_qos.o
 
 obj-$(CONFIG_FSL_ENETC_IERB) += fsl-enetc-ierb.o
 fsl-enetc-ierb-y := enetc_ierb.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc.c
@@ -121,6 +121,24 @@
 	return 0;
 }
 
+/**
+ * enetc_unwind_tx_frame() - Unwind the DMA mappings of a multi-buffer Tx frame
+ * @tx_ring: Pointer to the Tx ring on which the buffer descriptors are located
+ * @count: Number of Tx buffer descriptors which need to be unmapped
+ * @i: Index of the last successfully mapped Tx buffer descriptor
+ */
+static void enetc_unwind_tx_frame(struct enetc_bdr *tx_ring, int count, int i)
+{
+	while (count--) {
+		struct enetc_tx_swbd *tx_swbd = &tx_ring->tx_swbd[i];
+
+		enetc_free_tx_frame(tx_ring, tx_swbd);
+		if (i == 0)
+			i = tx_ring->bd_count;
+		i--;
+	}
+}
+
 static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb)
 {
 	bool do_vlan, do_onestep_tstamp = false, do_twostep_tstamp = false;
@@ -210,9 +228,11 @@
 		}
 
 		if (do_onestep_tstamp) {
-			u32 lo, hi, val;
-			u64 sec, nsec;
+			__be32 new_sec_l, new_nsec;
+			u32 lo, hi, nsec, val;
+			__be16 new_sec_h;
 			u8 *data;
+			u64 sec;
 
 			lo = enetc_rd_hot(hw, ENETC_SICTR0);
 			hi = enetc_rd_hot(hw, ENETC_SICTR1);
@@ -226,13 +246,38 @@
 			/* Update originTimestamp field of Sync packet
 			 * - 48 bits seconds field
 			 * - 32 bits nanseconds field
+			 *
+			 * In addition, the UDP checksum needs to be updated
+			 * by software after updating originTimestamp field,
+			 * otherwise the hardware will calculate the wrong
+			 * checksum when updating the correction field and
+			 * update it to the packet.
 			 */
 			data = skb_mac_header(skb);
-			*(__be16 *)(data + offset2) =
-				htons((sec >> 32) & 0xffff);
-			*(__be32 *)(data + offset2 + 2) =
-				htonl(sec & 0xffffffff);
-			*(__be32 *)(data + offset2 + 6) = htonl(nsec);
+			new_sec_h = htons((sec >> 32) & 0xffff);
+			new_sec_l = htonl(sec & 0xffffffff);
+			new_nsec = htonl(nsec);
+			if (udp) {
+				struct udphdr *uh = udp_hdr(skb);
+				__be32 old_sec_l, old_nsec;
+				__be16 old_sec_h;
+
+				old_sec_h = *(__be16 *)(data + offset2);
+				inet_proto_csum_replace2(&uh->check, skb, old_sec_h,
+							 new_sec_h, false);
+
+				old_sec_l = *(__be32 *)(data + offset2 + 2);
+				inet_proto_csum_replace4(&uh->check, skb, old_sec_l,
+							 new_sec_l, false);
+
+				old_nsec = *(__be32 *)(data + offset2 + 6);
+				inet_proto_csum_replace4(&uh->check, skb, old_nsec,
+							 new_nsec, false);
+			}
+
+			*(__be16 *)(data + offset2) = new_sec_h;
+			*(__be32 *)(data + offset2 + 2) = new_sec_l;
+			*(__be32 *)(data + offset2 + 6) = new_nsec;
 
 			/* Configure single-step register */
 			val = ENETC_PM0_SINGLE_STEP_EN;
@@ -303,13 +348,7 @@
 dma_err:
 	dev_err(tx_ring->dev, "DMA map error");
 
-	do {
-		tx_swbd = &tx_ring->tx_swbd[i];
-		enetc_free_tx_frame(tx_ring, tx_swbd);
-		if (i == 0)
-			i = tx_ring->bd_count;
-		i--;
-	} while (count--);
+	enetc_unwind_tx_frame(tx_ring, count, i);
 
 	return 0;
 }
@@ -940,7 +979,13 @@
 		if (!skb)
 			break;
 
-		rx_byte_cnt += skb->len;
+		/* When set, the outer VLAN header is extracted and reported
+		 * in the receive buffer descriptor. So rx_byte_cnt should
+		 * add the length of the extracted VLAN header.
+		 */
+		if (bd_status & ENETC_RXBD_FLAG_VLAN)
+			rx_byte_cnt += VLAN_HLEN;
+		rx_byte_cnt += skb->len + ETH_HLEN;
 		rx_frm_cnt++;
 
 		napi_gro_receive(napi, skb);
@@ -1217,24 +1262,6 @@
 				  &rx_ring->rx_swbd[rx_ring_first]);
 		enetc_bdr_idx_inc(rx_ring, &rx_ring_first);
 	}
-	rx_ring->stats.xdp_drops++;
-}
-
-static void enetc_xdp_free(struct enetc_bdr *rx_ring, int rx_ring_first,
-			   int rx_ring_last)
-{
-	while (rx_ring_first != rx_ring_last) {
-		struct enetc_rx_swbd *rx_swbd = &rx_ring->rx_swbd[rx_ring_first];
-
-		if (rx_swbd->page) {
-			dma_unmap_page(rx_ring->dev, rx_swbd->dma, PAGE_SIZE,
-				       rx_swbd->dir);
-			__free_page(rx_swbd->page);
-			rx_swbd->page = NULL;
-		}
-		enetc_bdr_idx_inc(rx_ring, &rx_ring_first);
-	}
-	rx_ring->stats.xdp_redirect_failures++;
 }
 
 static int enetc_clean_rx_ring_xdp(struct enetc_bdr *rx_ring,
@@ -1258,8 +1285,8 @@
 		int orig_i, orig_cleaned_cnt;
 		struct xdp_buff xdp_buff;
 		struct sk_buff *skb;
-		int tmp_orig_i, err;
 		u32 bd_status;
+		int err;
 
 		rxbd = enetc_rxbd(rx_ring, i);
 		bd_status = le32_to_cpu(rxbd->r.lstatus);
@@ -1291,6 +1318,7 @@
 			fallthrough;
 		case XDP_DROP:
 			enetc_xdp_drop(rx_ring, orig_i, i);
+			rx_ring->stats.xdp_drops++;
 			break;
 		case XDP_PASS:
 			rxbd = orig_rxbd;
@@ -1315,7 +1343,7 @@
 				enetc_xdp_drop(rx_ring, orig_i, i);
 				tx_ring->stats.xdp_tx_drops++;
 			} else {
-				tx_ring->stats.xdp_tx += xdp_tx_bd_cnt;
+				tx_ring->stats.xdp_tx++;
 				rx_ring->xdp.xdp_tx_in_flight += xdp_tx_bd_cnt;
 				xdp_tx_frm_cnt++;
 				/* The XDP_TX enqueue was successful, so we
@@ -1346,18 +1374,16 @@
 				break;
 			}
 
-			tmp_orig_i = orig_i;
-
-			while (orig_i != i) {
-				enetc_flip_rx_buff(rx_ring,
-						   &rx_ring->rx_swbd[orig_i]);
-				enetc_bdr_idx_inc(rx_ring, &orig_i);
-			}
-
 			err = xdp_do_redirect(rx_ring->ndev, &xdp_buff, prog);
 			if (unlikely(err)) {
-				enetc_xdp_free(rx_ring, tmp_orig_i, i);
+				enetc_xdp_drop(rx_ring, orig_i, i);
+				rx_ring->stats.xdp_redirect_failures++;
 			} else {
+				while (orig_i != i) {
+					enetc_flip_rx_buff(rx_ring,
+							   &rx_ring->rx_swbd[orig_i]);
+					enetc_bdr_idx_inc(rx_ring, &orig_i);
+				}
 				xdp_redirect_frm_cnt++;
 				rx_ring->stats.xdp_redirect++;
 			}
@@ -1768,7 +1794,7 @@
 	/* enable Tx ints by setting pkt thr to 1 */
 	enetc_txbdr_wr(hw, idx, ENETC_TBICR0, ENETC_TBICR0_ICEN | 0x1);
 
-	tbmr = ENETC_TBMR_EN;
+	tbmr = ENETC_TBMR_EN | ENETC_TBMR_SET_PRIO(tx_ring->prio);
 	if (tx_ring->ndev->features & NETIF_F_HW_VLAN_CTAG_TX)
 		tbmr |= ENETC_TBMR_VIH;
 
@@ -1800,7 +1826,12 @@
 	else
 		enetc_rxbdr_wr(hw, idx, ENETC_RBBSR, ENETC_RXB_DMA_SIZE);
 
+	/* Also prepare the consumer index in case page allocation never
+	 * succeeds. In that case, hardware will never advance producer index
+	 * to match consumer index, and will drop all frames.
+	 */
 	enetc_rxbdr_wr(hw, idx, ENETC_RBPIR, 0);
+	enetc_rxbdr_wr(hw, idx, ENETC_RBCIR, 1);
 
 	/* enable Rx ints by setting pkt thr to 1 */
 	enetc_rxbdr_wr(hw, idx, ENETC_RBICR0, ENETC_RBICR0_ICEN | 0x1);
@@ -1826,13 +1857,14 @@
 
 static void enetc_setup_bdrs(struct enetc_ndev_priv *priv)
 {
+	struct enetc_hw *hw = &priv->si->hw;
 	int i;
 
 	for (i = 0; i < priv->num_tx_rings; i++)
-		enetc_setup_txbdr(&priv->si->hw, priv->tx_ring[i]);
+		enetc_setup_txbdr(hw, priv->tx_ring[i]);
 
 	for (i = 0; i < priv->num_rx_rings; i++)
-		enetc_setup_rxbdr(&priv->si->hw, priv->rx_ring[i]);
+		enetc_setup_rxbdr(hw, priv->rx_ring[i]);
 }
 
 static void enetc_clear_rxbdr(struct enetc_hw *hw, struct enetc_bdr *rx_ring)
@@ -1865,13 +1897,14 @@
 
 static void enetc_clear_bdrs(struct enetc_ndev_priv *priv)
 {
+	struct enetc_hw *hw = &priv->si->hw;
 	int i;
 
 	for (i = 0; i < priv->num_tx_rings; i++)
-		enetc_clear_txbdr(&priv->si->hw, priv->tx_ring[i]);
+		enetc_clear_txbdr(hw, priv->tx_ring[i]);
 
 	for (i = 0; i < priv->num_rx_rings; i++)
-		enetc_clear_rxbdr(&priv->si->hw, priv->rx_ring[i]);
+		enetc_clear_rxbdr(hw, priv->rx_ring[i]);
 
 	udelay(1);
 }
@@ -1879,22 +1912,21 @@
 static int enetc_setup_irqs(struct enetc_ndev_priv *priv)
 {
 	struct pci_dev *pdev = priv->si->pdev;
+	struct enetc_hw *hw = &priv->si->hw;
 	int i, j, err;
 
 	for (i = 0; i < priv->bdr_int_num; i++) {
 		int irq = pci_irq_vector(pdev, ENETC_BDR_INT_BASE_IDX + i);
 		struct enetc_int_vector *v = priv->int_vector[i];
 		int entry = ENETC_BDR_INT_BASE_IDX + i;
-		struct enetc_hw *hw = &priv->si->hw;
 
 		snprintf(v->name, sizeof(v->name), "%s-rxtx%d",
 			 priv->ndev->name, i);
-		err = request_irq(irq, enetc_msix, 0, v->name, v);
+		err = request_irq(irq, enetc_msix, IRQF_NO_AUTOEN, v->name, v);
 		if (err) {
 			dev_err(priv->dev, "request_irq() failed!\n");
 			goto irq_err;
 		}
-		disable_irq(irq);
 
 		v->tbier_base = hw->reg + ENETC_BDR(TX, 0, ENETC_TBIER);
 		v->rbier = hw->reg + ENETC_BDR(RX, i, ENETC_RBIER);
@@ -1973,13 +2005,14 @@
 
 static void enetc_clear_interrupts(struct enetc_ndev_priv *priv)
 {
+	struct enetc_hw *hw = &priv->si->hw;
 	int i;
 
 	for (i = 0; i < priv->num_tx_rings; i++)
-		enetc_txbdr_wr(&priv->si->hw, i, ENETC_TBIER, 0);
+		enetc_txbdr_wr(hw, i, ENETC_TBIER, 0);
 
 	for (i = 0; i < priv->num_rx_rings; i++)
-		enetc_rxbdr_wr(&priv->si->hw, i, ENETC_RBIER, 0);
+		enetc_rxbdr_wr(hw, i, ENETC_RBIER, 0);
 }
 
 static int enetc_phylink_connect(struct net_device *ndev)
@@ -2011,14 +2044,14 @@
 
 	priv = container_of(work, struct enetc_ndev_priv, tx_onestep_tstamp);
 
-	netif_tx_lock(priv->ndev);
+	netif_tx_lock_bh(priv->ndev);
 
 	clear_bit_unlock(ENETC_TX_ONESTEP_TSTAMP_IN_PROGRESS, &priv->flags);
 	skb = skb_dequeue(&priv->tx_skbs);
 	if (skb)
 		enetc_start_xmit(skb, priv->ndev);
 
-	netif_tx_unlock(priv->ndev);
+	netif_tx_unlock_bh(priv->ndev);
 }
 
 static void enetc_tx_onestep_tstamp_init(struct enetc_ndev_priv *priv)
@@ -2142,10 +2175,11 @@
 	return 0;
 }
 
-static int enetc_setup_tc_mqprio(struct net_device *ndev, void *type_data)
+int enetc_setup_tc_mqprio(struct net_device *ndev, void *type_data)
 {
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
 	struct tc_mqprio_qopt *mqprio = type_data;
+	struct enetc_hw *hw = &priv->si->hw;
 	struct enetc_bdr *tx_ring;
 	int num_stack_tx_queues;
 	u8 num_tc;
@@ -2162,7 +2196,8 @@
 		/* Reset all ring priorities to 0 */
 		for (i = 0; i < priv->num_tx_rings; i++) {
 			tx_ring = priv->tx_ring[i];
-			enetc_set_bdr_prio(&priv->si->hw, tx_ring->index, 0);
+			tx_ring->prio = 0;
+			enetc_set_bdr_prio(hw, tx_ring->index, tx_ring->prio);
 		}
 
 		return 0;
@@ -2181,7 +2216,8 @@
 	 */
 	for (i = 0; i < num_tc; i++) {
 		tx_ring = priv->tx_ring[i];
-		enetc_set_bdr_prio(&priv->si->hw, tx_ring->index, i);
+		tx_ring->prio = i;
+		enetc_set_bdr_prio(hw, tx_ring->index, tx_ring->prio);
 	}
 
 	/* Reset the number of netdev queues based on the TC count */
@@ -2196,25 +2232,6 @@
 	return 0;
 }
 
-int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,
-		   void *type_data)
-{
-	switch (type) {
-	case TC_SETUP_QDISC_MQPRIO:
-		return enetc_setup_tc_mqprio(ndev, type_data);
-	case TC_SETUP_QDISC_TAPRIO:
-		return enetc_setup_tc_taprio(ndev, type_data);
-	case TC_SETUP_QDISC_CBS:
-		return enetc_setup_tc_cbs(ndev, type_data);
-	case TC_SETUP_QDISC_ETF:
-		return enetc_setup_tc_txtime(ndev, type_data);
-	case TC_SETUP_BLOCK:
-		return enetc_setup_tc_psfp(ndev, type_data);
-	default:
-		return -EOPNOTSUPP;
-	}
-}
-
 static int enetc_setup_xdp_prog(struct net_device *dev, struct bpf_prog *prog,
 				struct netlink_ext_ack *extack)
 {
@@ -2307,52 +2324,29 @@
 	return 0;
 }
 
-static int enetc_set_psfp(struct net_device *ndev, int en)
-{
-	struct enetc_ndev_priv *priv = netdev_priv(ndev);
-	int err;
-
-	if (en) {
-		err = enetc_psfp_enable(priv);
-		if (err)
-			return err;
-
-		priv->active_offloads |= ENETC_F_QCI;
-		return 0;
-	}
-
-	err = enetc_psfp_disable(priv);
-	if (err)
-		return err;
-
-	priv->active_offloads &= ~ENETC_F_QCI;
-
-	return 0;
-}
-
 static void enetc_enable_rxvlan(struct net_device *ndev, bool en)
 {
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
+	struct enetc_hw *hw = &priv->si->hw;
 	int i;
 
 	for (i = 0; i < priv->num_rx_rings; i++)
-		enetc_bdr_enable_rxvlan(&priv->si->hw, i, en);
+		enetc_bdr_enable_rxvlan(hw, i, en);
 }
 
 static void enetc_enable_txvlan(struct net_device *ndev, bool en)
 {
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
+	struct enetc_hw *hw = &priv->si->hw;
 	int i;
 
 	for (i = 0; i < priv->num_tx_rings; i++)
-		enetc_bdr_enable_txvlan(&priv->si->hw, i, en);
+		enetc_bdr_enable_txvlan(hw, i, en);
 }
 
-int enetc_set_features(struct net_device *ndev,
-		       netdev_features_t features)
+void enetc_set_features(struct net_device *ndev, netdev_features_t features)
 {
 	netdev_features_t changed = ndev->features ^ features;
-	int err = 0;
 
 	if (changed & NETIF_F_RXHASH)
 		enetc_set_rss(ndev, !!(features & NETIF_F_RXHASH));
@@ -2364,11 +2358,6 @@
 	if (changed & NETIF_F_HW_VLAN_CTAG_TX)
 		enetc_enable_txvlan(ndev,
 				    !!(features & NETIF_F_HW_VLAN_CTAG_TX));
-
-	if (changed & NETIF_F_HW_TC)
-		err = enetc_set_psfp(ndev, !!(features & NETIF_F_HW_TC));
-
-	return err;
 }
 
 #ifdef CONFIG_FSL_ENETC_PTP_CLOCK
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc.h
@@ -91,6 +91,7 @@
 		void __iomem *rcir;
 	};
 	u16 index;
+	u16 prio;
 	int bd_count; /* # of BDs */
 	int next_to_use;
 	int next_to_clean;
@@ -385,11 +386,9 @@
 void enetc_stop(struct net_device *ndev);
 netdev_tx_t enetc_xmit(struct sk_buff *skb, struct net_device *ndev);
 struct net_device_stats *enetc_get_stats(struct net_device *ndev);
-int enetc_set_features(struct net_device *ndev,
-		       netdev_features_t features);
+void enetc_set_features(struct net_device *ndev, netdev_features_t features);
 int enetc_ioctl(struct net_device *ndev, struct ifreq *rq, int cmd);
-int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,
-		   void *type_data);
+int enetc_setup_tc_mqprio(struct net_device *ndev, void *type_data);
 int enetc_setup_bpf(struct net_device *dev, struct netdev_bpf *xdp);
 int enetc_xdp_xmit(struct net_device *ndev, int num_frames,
 		   struct xdp_frame **frames, u32 flags);
@@ -421,22 +420,24 @@
 int enetc_setup_tc_psfp(struct net_device *ndev, void *type_data);
 int enetc_psfp_init(struct enetc_ndev_priv *priv);
 int enetc_psfp_clean(struct enetc_ndev_priv *priv);
+int enetc_set_psfp(struct net_device *ndev, bool en);
 
 static inline void enetc_get_max_cap(struct enetc_ndev_priv *priv)
 {
+	struct enetc_hw *hw = &priv->si->hw;
 	u32 reg;
 
-	reg = enetc_port_rd(&priv->si->hw, ENETC_PSIDCAPR);
+	reg = enetc_port_rd(hw, ENETC_PSIDCAPR);
 	priv->psfp_cap.max_streamid = reg & ENETC_PSIDCAPR_MSK;
 	/* Port stream filter capability */
-	reg = enetc_port_rd(&priv->si->hw, ENETC_PSFCAPR);
+	reg = enetc_port_rd(hw, ENETC_PSFCAPR);
 	priv->psfp_cap.max_psfp_filter = reg & ENETC_PSFCAPR_MSK;
 	/* Port stream gate capability */
-	reg = enetc_port_rd(&priv->si->hw, ENETC_PSGCAPR);
+	reg = enetc_port_rd(hw, ENETC_PSGCAPR);
 	priv->psfp_cap.max_psfp_gate = (reg & ENETC_PSGCAPR_SGIT_MSK);
 	priv->psfp_cap.max_psfp_gatelist = (reg & ENETC_PSGCAPR_GCL_MSK) >> 16;
 	/* Port flow meter capability */
-	reg = enetc_port_rd(&priv->si->hw, ENETC_PFMCAPR);
+	reg = enetc_port_rd(hw, ENETC_PFMCAPR);
 	priv->psfp_cap.max_psfp_meter = reg & ENETC_PFMCAPR_MSK;
 }
 
@@ -496,4 +497,9 @@
 {
 	return 0;
 }
+
+static inline int enetc_set_psfp(struct net_device *ndev, bool en)
+{
+	return 0;
+}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc_ethtool.c
@@ -672,7 +672,10 @@
 #ifdef CONFIG_FSL_ENETC_PTP_CLOCK
 	info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE |
 				SOF_TIMESTAMPING_RX_HARDWARE |
-				SOF_TIMESTAMPING_RAW_HARDWARE;
+				SOF_TIMESTAMPING_RAW_HARDWARE |
+				SOF_TIMESTAMPING_TX_SOFTWARE |
+				SOF_TIMESTAMPING_RX_SOFTWARE |
+				SOF_TIMESTAMPING_SOFTWARE;
 
 	info->tx_types = (1 << HWTSTAMP_TX_OFF) |
 			 (1 << HWTSTAMP_TX_ON) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc_pf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc_pf.c
@@ -708,6 +708,13 @@
 {
 	netdev_features_t changed = ndev->features ^ features;
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
+	int err;
+
+	if (changed & NETIF_F_HW_TC) {
+		err = enetc_set_psfp(ndev, !!(features & NETIF_F_HW_TC));
+		if (err)
+			return err;
+	}
 
 	if (changed & NETIF_F_HW_VLAN_CTAG_FILTER) {
 		struct enetc_pf *pf = enetc_si_priv(priv->si);
@@ -721,7 +728,28 @@
 	if (changed & NETIF_F_LOOPBACK)
 		enetc_set_loopback(ndev, !!(features & NETIF_F_LOOPBACK));
 
-	return enetc_set_features(ndev, features);
+	enetc_set_features(ndev, features);
+
+	return 0;
+}
+
+static int enetc_pf_setup_tc(struct net_device *ndev, enum tc_setup_type type,
+			     void *type_data)
+{
+	switch (type) {
+	case TC_SETUP_QDISC_MQPRIO:
+		return enetc_setup_tc_mqprio(ndev, type_data);
+	case TC_SETUP_QDISC_TAPRIO:
+		return enetc_setup_tc_taprio(ndev, type_data);
+	case TC_SETUP_QDISC_CBS:
+		return enetc_setup_tc_cbs(ndev, type_data);
+	case TC_SETUP_QDISC_ETF:
+		return enetc_setup_tc_txtime(ndev, type_data);
+	case TC_SETUP_BLOCK:
+		return enetc_setup_tc_psfp(ndev, type_data);
+	default:
+		return -EOPNOTSUPP;
+	}
 }
 
 static const struct net_device_ops enetc_ndev_ops = {
@@ -738,7 +766,7 @@
 	.ndo_set_vf_spoofchk	= enetc_pf_set_vf_spoofchk,
 	.ndo_set_features	= enetc_pf_set_features,
 	.ndo_eth_ioctl		= enetc_ioctl,
-	.ndo_setup_tc		= enetc_setup_tc,
+	.ndo_setup_tc		= enetc_pf_setup_tc,
 	.ndo_bpf		= enetc_setup_bpf,
 	.ndo_xdp_xmit		= enetc_xdp_xmit,
 };
@@ -772,9 +800,6 @@
 
 	ndev->priv_flags |= IFF_UNICAST_FLT;
 
-	if (si->hw_features & ENETC_SI_F_QBV)
-		priv->active_offloads |= ENETC_F_QBV;
-
 	if (si->hw_features & ENETC_SI_F_PSFP && !enetc_psfp_enable(priv)) {
 		priv->active_offloads |= ENETC_F_QCI;
 		ndev->features |= NETIF_F_HW_TC;
@@ -1025,7 +1050,8 @@
 	int idx;
 
 	priv = netdev_priv(pf->si->ndev);
-	if (priv->active_offloads & ENETC_F_QBV)
+
+	if (pf->si->hw_features & ENETC_SI_F_QBV)
 		enetc_sched_speed_set(priv, speed);
 
 	if (!phylink_autoneg_inband(mode) &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc_ptp.c
@@ -8,7 +8,7 @@
 #include "enetc.h"
 
 int enetc_phc_index = -1;
-EXPORT_SYMBOL(enetc_phc_index);
+EXPORT_SYMBOL_GPL(enetc_phc_index);
 
 static struct ptp_clock_info enetc_ptp_caps = {
 	.owner		= THIS_MODULE,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc_qos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc_qos.c
@@ -17,8 +17,9 @@
 
 void enetc_sched_speed_set(struct enetc_ndev_priv *priv, int speed)
 {
+	struct enetc_hw *hw = &priv->si->hw;
 	u32 old_speed = priv->speed;
-	u32 pspeed;
+	u32 pspeed, tmp;
 
 	if (speed == old_speed)
 		return;
@@ -39,36 +40,38 @@
 	}
 
 	priv->speed = speed;
-	enetc_port_wr(&priv->si->hw, ENETC_PMR,
-		      (enetc_port_rd(&priv->si->hw, ENETC_PMR)
-		      & (~ENETC_PMR_PSPEED_MASK))
-		      | pspeed);
+	tmp = enetc_port_rd(hw, ENETC_PMR);
+	enetc_port_wr(hw, ENETC_PMR, (tmp & ~ENETC_PMR_PSPEED_MASK) | pspeed);
 }
 
+#define ENETC_QOS_ALIGN	64
 static int enetc_setup_taprio(struct net_device *ndev,
 			      struct tc_taprio_qopt_offload *admin_conf)
 {
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
+	struct enetc_hw *hw = &priv->si->hw;
 	struct enetc_cbd cbd = {.cmd = 0};
 	struct tgs_gcl_conf *gcl_config;
 	struct tgs_gcl_data *gcl_data;
+	dma_addr_t dma, dma_align;
 	struct gce *gce;
-	dma_addr_t dma;
 	u16 data_size;
 	u16 gcl_len;
+	void *tmp;
 	u32 tge;
 	int err;
 	int i;
 
-	if (admin_conf->num_entries > enetc_get_max_gcl_len(&priv->si->hw))
+	if (admin_conf->num_entries > enetc_get_max_gcl_len(hw))
 		return -EINVAL;
 	gcl_len = admin_conf->num_entries;
 
-	tge = enetc_rd(&priv->si->hw, ENETC_QBV_PTGCR_OFFSET);
+	tge = enetc_rd(hw, ENETC_QBV_PTGCR_OFFSET);
 	if (!admin_conf->enable) {
-		enetc_wr(&priv->si->hw,
-			 ENETC_QBV_PTGCR_OFFSET,
-			 tge & (~ENETC_QBV_TGE));
+		enetc_wr(hw, ENETC_QBV_PTGCR_OFFSET, tge & ~ENETC_QBV_TGE);
+
+		priv->active_offloads &= ~ENETC_F_QBV;
+
 		return 0;
 	}
 
@@ -82,9 +85,16 @@
 	gcl_config = &cbd.gcl_conf;
 
 	data_size = struct_size(gcl_data, entry, gcl_len);
-	gcl_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
-	if (!gcl_data)
+	tmp = dma_alloc_coherent(&priv->si->pdev->dev,
+				 data_size + ENETC_QOS_ALIGN,
+				 &dma, GFP_KERNEL);
+	if (!tmp) {
+		dev_err(&priv->si->pdev->dev,
+			"DMA mapping of taprio gate list failed!\n");
 		return -ENOMEM;
+	}
+	dma_align = ALIGN(dma, ENETC_QOS_ALIGN);
+	gcl_data = (struct tgs_gcl_data *)PTR_ALIGN(tmp, ENETC_QOS_ALIGN);
 
 	gce = (struct gce *)(gcl_data + 1);
 
@@ -110,30 +120,22 @@
 	cbd.length = cpu_to_le16(data_size);
 	cbd.status_flags = 0;
 
-	dma = dma_map_single(&priv->si->pdev->dev, gcl_data,
-			     data_size, DMA_TO_DEVICE);
-	if (dma_mapping_error(&priv->si->pdev->dev, dma)) {
-		netdev_err(priv->si->ndev, "DMA mapping failed!\n");
-		kfree(gcl_data);
-		return -ENOMEM;
-	}
-
-	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma));
-	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma));
+	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma_align));
+	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma_align));
 	cbd.cls = BDCR_CMD_PORT_GCL;
 	cbd.status_flags = 0;
 
-	enetc_wr(&priv->si->hw, ENETC_QBV_PTGCR_OFFSET,
-		 tge | ENETC_QBV_TGE);
+	enetc_wr(hw, ENETC_QBV_PTGCR_OFFSET, tge | ENETC_QBV_TGE);
 
 	err = enetc_send_cmd(priv->si, &cbd);
 	if (err)
-		enetc_wr(&priv->si->hw,
-			 ENETC_QBV_PTGCR_OFFSET,
-			 tge & (~ENETC_QBV_TGE));
+		enetc_wr(hw, ENETC_QBV_PTGCR_OFFSET, tge & ~ENETC_QBV_TGE);
 
-	dma_unmap_single(&priv->si->pdev->dev, dma, data_size, DMA_TO_DEVICE);
-	kfree(gcl_data);
+	dma_free_coherent(&priv->si->pdev->dev, data_size + ENETC_QOS_ALIGN,
+			  tmp, dma);
+
+	if (!err)
+		priv->active_offloads |= ENETC_F_QBV;
 
 	return err;
 }
@@ -142,6 +144,8 @@
 {
 	struct tc_taprio_qopt_offload *taprio = type_data;
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
+	struct enetc_hw *hw = &priv->si->hw;
+	struct enetc_bdr *tx_ring;
 	int err;
 	int i;
 
@@ -150,18 +154,20 @@
 		if (priv->tx_ring[i]->tsd_enable)
 			return -EBUSY;
 
-	for (i = 0; i < priv->num_tx_rings; i++)
-		enetc_set_bdr_prio(&priv->si->hw,
-				   priv->tx_ring[i]->index,
-				   taprio->enable ? i : 0);
+	for (i = 0; i < priv->num_tx_rings; i++) {
+		tx_ring = priv->tx_ring[i];
+		tx_ring->prio = taprio->enable ? i : 0;
+		enetc_set_bdr_prio(hw, tx_ring->index, tx_ring->prio);
+	}
 
 	err = enetc_setup_taprio(ndev, taprio);
-
-	if (err)
-		for (i = 0; i < priv->num_tx_rings; i++)
-			enetc_set_bdr_prio(&priv->si->hw,
-					   priv->tx_ring[i]->index,
-					   taprio->enable ? 0 : i);
+	if (err) {
+		for (i = 0; i < priv->num_tx_rings; i++) {
+			tx_ring = priv->tx_ring[i];
+			tx_ring->prio = taprio->enable ? 0 : i;
+			enetc_set_bdr_prio(hw, tx_ring->index, tx_ring->prio);
+		}
+	}
 
 	return err;
 }
@@ -182,7 +188,7 @@
 	struct tc_cbs_qopt_offload *cbs = type_data;
 	u32 port_transmit_rate = priv->speed;
 	u8 tc_nums = netdev_get_num_tc(ndev);
-	struct enetc_si *si = priv->si;
+	struct enetc_hw *hw = &priv->si->hw;
 	u32 hi_credit_bit, hi_credit_reg;
 	u32 max_interference_size;
 	u32 port_frame_max_size;
@@ -191,8 +197,8 @@
 	int bw_sum = 0;
 	u8 bw;
 
-	prio_top = netdev_get_prio_tc_map(ndev, tc_nums - 1);
-	prio_next = netdev_get_prio_tc_map(ndev, tc_nums - 2);
+	prio_top = tc_nums - 1;
+	prio_next = tc_nums - 2;
 
 	/* Support highest prio and second prio tc in cbs mode */
 	if (tc != prio_top && tc != prio_next)
@@ -203,15 +209,15 @@
 		 * lower than this TC have been disabled.
 		 */
 		if (tc == prio_top &&
-		    enetc_get_cbs_enable(&si->hw, prio_next)) {
+		    enetc_get_cbs_enable(hw, prio_next)) {
 			dev_err(&ndev->dev,
 				"Disable TC%d before disable TC%d\n",
 				prio_next, tc);
 			return -EINVAL;
 		}
 
-		enetc_port_wr(&si->hw, ENETC_PTCCBSR1(tc), 0);
-		enetc_port_wr(&si->hw, ENETC_PTCCBSR0(tc), 0);
+		enetc_port_wr(hw, ENETC_PTCCBSR1(tc), 0);
+		enetc_port_wr(hw, ENETC_PTCCBSR0(tc), 0);
 
 		return 0;
 	}
@@ -228,13 +234,13 @@
 	 * higher than this TC have been enabled.
 	 */
 	if (tc == prio_next) {
-		if (!enetc_get_cbs_enable(&si->hw, prio_top)) {
+		if (!enetc_get_cbs_enable(hw, prio_top)) {
 			dev_err(&ndev->dev,
 				"Enable TC%d first before enable TC%d\n",
 				prio_top, prio_next);
 			return -EINVAL;
 		}
-		bw_sum += enetc_get_cbs_bw(&si->hw, prio_top);
+		bw_sum += enetc_get_cbs_bw(hw, prio_top);
 	}
 
 	if (bw_sum + bw >= 100) {
@@ -243,7 +249,7 @@
 		return -EINVAL;
 	}
 
-	enetc_port_rd(&si->hw, ENETC_PTCMSDUR(tc));
+	enetc_port_rd(hw, ENETC_PTCMSDUR(tc));
 
 	/* For top prio TC, the max_interfrence_size is maxSizedFrame.
 	 *
@@ -263,8 +269,8 @@
 		u32 m0, ma, r0, ra;
 
 		m0 = port_frame_max_size * 8;
-		ma = enetc_port_rd(&si->hw, ENETC_PTCMSDUR(prio_top)) * 8;
-		ra = enetc_get_cbs_bw(&si->hw, prio_top) *
+		ma = enetc_port_rd(hw, ENETC_PTCMSDUR(prio_top)) * 8;
+		ra = enetc_get_cbs_bw(hw, prio_top) *
 			port_transmit_rate * 10000ULL;
 		r0 = port_transmit_rate * 1000000ULL;
 		max_interference_size = m0 + ma +
@@ -284,10 +290,10 @@
 	hi_credit_reg = (u32)div_u64((ENETC_CLK * 100ULL) * hi_credit_bit,
 				     port_transmit_rate * 1000000ULL);
 
-	enetc_port_wr(&si->hw, ENETC_PTCCBSR1(tc), hi_credit_reg);
+	enetc_port_wr(hw, ENETC_PTCCBSR1(tc), hi_credit_reg);
 
 	/* Set bw register and enable this traffic class */
-	enetc_port_wr(&si->hw, ENETC_PTCCBSR0(tc), bw | ENETC_CBSE);
+	enetc_port_wr(hw, ENETC_PTCCBSR0(tc), bw | ENETC_CBSE);
 
 	return 0;
 }
@@ -297,6 +303,7 @@
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
 	struct tc_etf_qopt_offload *qopt = type_data;
 	u8 tc_nums = netdev_get_num_tc(ndev);
+	struct enetc_hw *hw = &priv->si->hw;
 	int tc;
 
 	if (!tc_nums)
@@ -312,12 +319,11 @@
 		return -EBUSY;
 
 	/* TSD and Qbv are mutually exclusive in hardware */
-	if (enetc_rd(&priv->si->hw, ENETC_QBV_PTGCR_OFFSET) & ENETC_QBV_TGE)
+	if (enetc_rd(hw, ENETC_QBV_PTGCR_OFFSET) & ENETC_QBV_TGE)
 		return -EBUSY;
 
 	priv->tx_ring[tc]->tsd_enable = qopt->enable;
-	enetc_port_wr(&priv->si->hw, ENETC_PTCTSDR(tc),
-		      qopt->enable ? ENETC_TSDE : 0);
+	enetc_port_wr(hw, ENETC_PTCTSDR(tc), qopt->enable ? ENETC_TSDE : 0);
 
 	return 0;
 }
@@ -463,8 +469,9 @@
 	struct enetc_cbd cbd = {.cmd = 0};
 	struct streamid_data *si_data;
 	struct streamid_conf *si_conf;
+	dma_addr_t dma, dma_align;
 	u16 data_size;
-	dma_addr_t dma;
+	void *tmp;
 	int port;
 	int err;
 
@@ -485,19 +492,20 @@
 	cbd.status_flags = 0;
 
 	data_size = sizeof(struct streamid_data);
-	si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
-	cbd.length = cpu_to_le16(data_size);
-
-	dma = dma_map_single(&priv->si->pdev->dev, si_data,
-			     data_size, DMA_FROM_DEVICE);
-	if (dma_mapping_error(&priv->si->pdev->dev, dma)) {
-		netdev_err(priv->si->ndev, "DMA mapping failed!\n");
-		kfree(si_data);
+	tmp = dma_alloc_coherent(&priv->si->pdev->dev,
+				 data_size + ENETC_QOS_ALIGN,
+				 &dma, GFP_KERNEL);
+	if (!tmp) {
+		dev_err(&priv->si->pdev->dev,
+			"DMA mapping of stream identify failed!\n");
 		return -ENOMEM;
 	}
+	dma_align = ALIGN(dma, ENETC_QOS_ALIGN);
+	si_data = (struct streamid_data *)PTR_ALIGN(tmp, ENETC_QOS_ALIGN);
 
-	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma));
-	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma));
+	cbd.length = cpu_to_le16(data_size);
+	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma_align));
+	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma_align));
 	eth_broadcast_addr(si_data->dmac);
 	si_data->vid_vidm_tg = (ENETC_CBDR_SID_VID_MASK
 			       + ((0x3 << 14) | ENETC_CBDR_SID_VIDM));
@@ -512,12 +520,10 @@
 
 	err = enetc_send_cmd(priv->si, &cbd);
 	if (err)
-		return -EINVAL;
+		goto out;
 
-	if (!enable) {
-		kfree(si_data);
-		return 0;
-	}
+	if (!enable)
+		goto out;
 
 	/* Enable the entry overwrite again incase space flushed by hardware */
 	memset(&cbd, 0, sizeof(cbd));
@@ -539,8 +545,8 @@
 
 	cbd.length = cpu_to_le16(data_size);
 
-	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma));
-	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma));
+	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma_align));
+	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma_align));
 
 	/* VIDM default to be 1.
 	 * VID Match. If set (b1) then the VID must match, otherwise
@@ -560,7 +566,9 @@
 	}
 
 	err = enetc_send_cmd(priv->si, &cbd);
-	kfree(si_data);
+out:
+	dma_free_coherent(&priv->si->pdev->dev, data_size + ENETC_QOS_ALIGN,
+			  tmp, dma);
 
 	return err;
 }
@@ -629,8 +637,9 @@
 {
 	struct enetc_cbd cbd = { .cmd = 2 };
 	struct sfi_counter_data *data_buf;
-	dma_addr_t dma;
+	dma_addr_t dma, dma_align;
 	u16 data_size;
+	void *tmp;
 	int err;
 
 	cbd.index = cpu_to_le16((u16)index);
@@ -639,19 +648,19 @@
 	cbd.status_flags = 0;
 
 	data_size = sizeof(struct sfi_counter_data);
-	data_buf = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
-	if (!data_buf)
+	tmp = dma_alloc_coherent(&priv->si->pdev->dev,
+				 data_size + ENETC_QOS_ALIGN,
+				 &dma, GFP_KERNEL);
+	if (!tmp) {
+		dev_err(&priv->si->pdev->dev,
+			"DMA mapping of stream counter failed!\n");
 		return -ENOMEM;
-
-	dma = dma_map_single(&priv->si->pdev->dev, data_buf,
-			     data_size, DMA_FROM_DEVICE);
-	if (dma_mapping_error(&priv->si->pdev->dev, dma)) {
-		netdev_err(priv->si->ndev, "DMA mapping failed!\n");
-		err = -ENOMEM;
-		goto exit;
 	}
-	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma));
-	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma));
+	dma_align = ALIGN(dma, ENETC_QOS_ALIGN);
+	data_buf = (struct sfi_counter_data *)PTR_ALIGN(tmp, ENETC_QOS_ALIGN);
+
+	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma_align));
+	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma_align));
 
 	cbd.length = cpu_to_le16(data_size);
 
@@ -680,7 +689,9 @@
 				data_buf->flow_meter_dropl;
 
 exit:
-	kfree(data_buf);
+	dma_free_coherent(&priv->si->pdev->dev, data_size + ENETC_QOS_ALIGN,
+			  tmp, dma);
+
 	return err;
 }
 
@@ -719,9 +730,10 @@
 	struct sgcl_conf *sgcl_config;
 	struct sgcl_data *sgcl_data;
 	struct sgce *sgce;
-	dma_addr_t dma;
+	dma_addr_t dma, dma_align;
 	u16 data_size;
 	int err, i;
+	void *tmp;
 	u64 now;
 
 	cbd.index = cpu_to_le16(sgi->index);
@@ -768,24 +780,20 @@
 	sgcl_config->acl_len = (sgi->num_entries - 1) & 0x3;
 
 	data_size = struct_size(sgcl_data, sgcl, sgi->num_entries);
-
-	sgcl_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
-	if (!sgcl_data)
-		return -ENOMEM;
-
-	cbd.length = cpu_to_le16(data_size);
-
-	dma = dma_map_single(&priv->si->pdev->dev,
-			     sgcl_data, data_size,
-			     DMA_FROM_DEVICE);
-	if (dma_mapping_error(&priv->si->pdev->dev, dma)) {
-		netdev_err(priv->si->ndev, "DMA mapping failed!\n");
-		kfree(sgcl_data);
+	tmp = dma_alloc_coherent(&priv->si->pdev->dev,
+				 data_size + ENETC_QOS_ALIGN,
+				 &dma, GFP_KERNEL);
+	if (!tmp) {
+		dev_err(&priv->si->pdev->dev,
+			"DMA mapping of stream counter failed!\n");
 		return -ENOMEM;
 	}
+	dma_align = ALIGN(dma, ENETC_QOS_ALIGN);
+	sgcl_data = (struct sgcl_data *)PTR_ALIGN(tmp, ENETC_QOS_ALIGN);
 
-	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma));
-	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma));
+	cbd.length = cpu_to_le16(data_size);
+	cbd.addr[0] = cpu_to_le32(lower_32_bits(dma_align));
+	cbd.addr[1] = cpu_to_le32(upper_32_bits(dma_align));
 
 	sgce = &sgcl_data->sgcl[0];
 
@@ -840,7 +848,8 @@
 	err = enetc_send_cmd(priv->si, &cbd);
 
 exit:
-	kfree(sgcl_data);
+	dma_free_coherent(&priv->si->pdev->dev, data_size + ENETC_QOS_ALIGN,
+			  tmp, dma);
 
 	return err;
 }
@@ -1261,7 +1270,7 @@
 		int index;
 
 		index = enetc_get_free_index(priv);
-		if (sfi->handle < 0) {
+		if (index < 0) {
 			NL_SET_ERR_MSG_MOD(extack, "No Stream Filter resource!");
 			err = -ENOSPC;
 			goto free_fmi;
@@ -1525,6 +1534,29 @@
 	}
 }
 
+int enetc_set_psfp(struct net_device *ndev, bool en)
+{
+	struct enetc_ndev_priv *priv = netdev_priv(ndev);
+	int err;
+
+	if (en) {
+		err = enetc_psfp_enable(priv);
+		if (err)
+			return err;
+
+		priv->active_offloads |= ENETC_F_QCI;
+		return 0;
+	}
+
+	err = enetc_psfp_disable(priv);
+	if (err)
+		return err;
+
+	priv->active_offloads &= ~ENETC_F_QCI;
+
+	return 0;
+}
+
 int enetc_psfp_init(struct enetc_ndev_priv *priv)
 {
 	if (epsfp.psfp_sfi_bitmap)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/enetc/enetc_vf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/enetc/enetc_vf.c
@@ -78,17 +78,37 @@
 {
 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
 	struct sockaddr *saddr = addr;
+	int err;
 
 	if (!is_valid_ether_addr(saddr->sa_data))
 		return -EADDRNOTAVAIL;
 
-	return enetc_msg_vsi_set_primary_mac_addr(priv, saddr);
+	err = enetc_msg_vsi_set_primary_mac_addr(priv, saddr);
+	if (err)
+		return err;
+
+	eth_hw_addr_set(ndev, saddr->sa_data);
+
+	return 0;
 }
 
 static int enetc_vf_set_features(struct net_device *ndev,
 				 netdev_features_t features)
 {
-	return enetc_set_features(ndev, features);
+	enetc_set_features(ndev, features);
+
+	return 0;
+}
+
+static int enetc_vf_setup_tc(struct net_device *ndev, enum tc_setup_type type,
+			     void *type_data)
+{
+	switch (type) {
+	case TC_SETUP_QDISC_MQPRIO:
+		return enetc_setup_tc_mqprio(ndev, type_data);
+	default:
+		return -EOPNOTSUPP;
+	}
 }
 
 /* Probing/ Init */
@@ -100,7 +120,7 @@
 	.ndo_set_mac_address	= enetc_vf_set_mac_addr,
 	.ndo_set_features	= enetc_vf_set_features,
 	.ndo_eth_ioctl		= enetc_ioctl,
-	.ndo_setup_tc		= enetc_setup_tc,
+	.ndo_setup_tc		= enetc_vf_setup_tc,
 };
 
 static void enetc_vf_netdev_setup(struct enetc_si *si, struct net_device *ndev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fec.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fec.h
@@ -377,6 +377,9 @@
 #define FEC_ENET_WAKEUP	((uint)0x00020000)	/* Wakeup request */
 #define FEC_ENET_TXF	(FEC_ENET_TXF_0 | FEC_ENET_TXF_1 | FEC_ENET_TXF_2)
 #define FEC_ENET_RXF	(FEC_ENET_RXF_0 | FEC_ENET_RXF_1 | FEC_ENET_RXF_2)
+#define FEC_ENET_RXF_GET(X)	(((X) == 0) ? FEC_ENET_RXF_0 :	\
+				(((X) == 1) ? FEC_ENET_RXF_1 :	\
+				FEC_ENET_RXF_2))
 #define FEC_ENET_TS_AVAIL       ((uint)0x00010000)
 #define FEC_ENET_TS_TIMER       ((uint)0x00008000)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fec_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fec_main.c
@@ -72,7 +72,7 @@
 #include "fec.h"
 
 static void set_multicast_list(struct net_device *ndev);
-static void fec_enet_itr_coal_init(struct net_device *ndev);
+static void fec_enet_itr_coal_set(struct net_device *ndev);
 
 #define DRIVER_NAME	"fec"
 
@@ -252,8 +252,8 @@
 #define PKT_MINBUF_SIZE		64
 
 /* FEC receive acceleration */
-#define FEC_RACC_IPDIS		(1 << 1)
-#define FEC_RACC_PRODIS		(1 << 2)
+#define FEC_RACC_IPDIS		BIT(1)
+#define FEC_RACC_PRODIS		BIT(2)
 #define FEC_RACC_SHIFT16	BIT(7)
 #define FEC_RACC_OPTIONS	(FEC_RACC_IPDIS | FEC_RACC_PRODIS)
 
@@ -285,8 +285,23 @@
 #define FEC_MMFR_TA		(2 << 16)
 #define FEC_MMFR_DATA(v)	(v & 0xffff)
 /* FEC ECR bits definition */
-#define FEC_ECR_MAGICEN		(1 << 2)
-#define FEC_ECR_SLEEP		(1 << 3)
+#define FEC_ECR_RESET           BIT(0)
+#define FEC_ECR_ETHEREN         BIT(1)
+#define FEC_ECR_MAGICEN         BIT(2)
+#define FEC_ECR_SLEEP           BIT(3)
+#define FEC_ECR_EN1588          BIT(4)
+#define FEC_ECR_BYTESWP         BIT(8)
+/* FEC RCR bits definition */
+#define FEC_RCR_LOOP            BIT(0)
+#define FEC_RCR_HALFDPX         BIT(1)
+#define FEC_RCR_MII             BIT(2)
+#define FEC_RCR_PROMISC         BIT(3)
+#define FEC_RCR_BC_REJ          BIT(4)
+#define FEC_RCR_FLOWCTL         BIT(5)
+#define FEC_RCR_RMII            BIT(8)
+#define FEC_RCR_10BASET         BIT(9)
+/* TX WMARK bits */
+#define FEC_TXWMRK_STRFWD       BIT(8)
 
 #define FEC_MII_TIMEOUT		30000 /* us */
 
@@ -656,7 +671,7 @@
 		dev_kfree_skb_any(skb);
 		if (net_ratelimit())
 			netdev_err(ndev, "Tx DMA memory map failed\n");
-		return NETDEV_TX_BUSY;
+		return NETDEV_TX_OK;
 	}
 
 	bdp->cbd_datlen = cpu_to_fec16(size);
@@ -718,7 +733,7 @@
 			dev_kfree_skb_any(skb);
 			if (net_ratelimit())
 				netdev_err(ndev, "Tx DMA memory map failed\n");
-			return NETDEV_TX_BUSY;
+			return NETDEV_TX_OK;
 		}
 	}
 
@@ -746,6 +761,8 @@
 	struct fec_enet_private *fep = netdev_priv(ndev);
 	int hdr_len, total_len, data_left;
 	struct bufdesc *bdp = txq->bd.cur;
+	struct bufdesc *tmp_bdp;
+	struct bufdesc_ex *ebdp;
 	struct tso_t tso;
 	unsigned int index = 0;
 	int ret;
@@ -819,7 +836,34 @@
 	return 0;
 
 err_release:
-	/* TODO: Release all used data descriptors for TSO */
+	/* Release all used data descriptors for TSO */
+	tmp_bdp = txq->bd.cur;
+
+	while (tmp_bdp != bdp) {
+		/* Unmap data buffers */
+		if (tmp_bdp->cbd_bufaddr &&
+		    !IS_TSO_HEADER(txq, fec32_to_cpu(tmp_bdp->cbd_bufaddr)))
+			dma_unmap_single(&fep->pdev->dev,
+					 fec32_to_cpu(tmp_bdp->cbd_bufaddr),
+					 fec16_to_cpu(tmp_bdp->cbd_datlen),
+					 DMA_TO_DEVICE);
+
+		/* Clear standard buffer descriptor fields */
+		tmp_bdp->cbd_sc = 0;
+		tmp_bdp->cbd_datlen = 0;
+		tmp_bdp->cbd_bufaddr = 0;
+
+		/* Handle extended descriptor if enabled */
+		if (fep->bufdesc_ex) {
+			ebdp = (struct bufdesc_ex *)tmp_bdp;
+			ebdp->cbd_esc = 0;
+		}
+
+		tmp_bdp = fec_enet_get_nextdesc(tmp_bdp, &txq->bd);
+	}
+
+	dev_kfree_skb_any(skb);
+
 	return ret;
 }
 
@@ -981,7 +1025,7 @@
 	struct fec_enet_private *fep = netdev_priv(ndev);
 	u32 temp_mac[2];
 	u32 rcntl = OPT_FRAME_SIZE | 0x04;
-	u32 ecntl = 0x2; /* ETHEREN */
+	u32 ecntl = FEC_ECR_ETHEREN;
 
 	/* Whack a reset.  We should wait for this.
 	 * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
@@ -1059,18 +1103,18 @@
 		    fep->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID)
 			rcntl |= (1 << 6);
 		else if (fep->phy_interface == PHY_INTERFACE_MODE_RMII)
-			rcntl |= (1 << 8);
+			rcntl |= FEC_RCR_RMII;
 		else
-			rcntl &= ~(1 << 8);
+			rcntl &= ~FEC_RCR_RMII;
 
 		/* 1G, 100M or 10M */
 		if (ndev->phydev) {
 			if (ndev->phydev->speed == SPEED_1000)
 				ecntl |= (1 << 5);
 			else if (ndev->phydev->speed == SPEED_100)
-				rcntl &= ~(1 << 9);
+				rcntl &= ~FEC_RCR_10BASET;
 			else
-				rcntl |= (1 << 9);
+				rcntl |= FEC_RCR_10BASET;
 		}
 	} else {
 #ifdef FEC_MIIGSK_ENR
@@ -1129,13 +1173,13 @@
 
 	if (fep->quirks & FEC_QUIRK_ENET_MAC) {
 		/* enable ENET endian swap */
-		ecntl |= (1 << 8);
+		ecntl |= FEC_ECR_BYTESWP;
 		/* enable ENET store and forward mode */
-		writel(1 << 8, fep->hwp + FEC_X_WMRK);
+		writel(FEC_TXWMRK_STRFWD, fep->hwp + FEC_X_WMRK);
 	}
 
 	if (fep->bufdesc_ex)
-		ecntl |= (1 << 4);
+		ecntl |= FEC_ECR_EN1588;
 
 	if (fep->quirks & FEC_QUIRK_DELAYED_CLKS_SUPPORT &&
 	    fep->rgmii_txc_dly)
@@ -1163,8 +1207,8 @@
 		writel(0, fep->hwp + FEC_IMASK);
 
 	/* Init the interrupt coalescing */
-	fec_enet_itr_coal_init(ndev);
-
+	if (fep->quirks & FEC_QUIRK_HAS_COALESCE)
+		fec_enet_itr_coal_set(ndev);
 }
 
 static void fec_enet_stop_mode(struct fec_enet_private *fep, bool enabled)
@@ -1189,7 +1233,7 @@
 fec_stop(struct net_device *ndev)
 {
 	struct fec_enet_private *fep = netdev_priv(ndev);
-	u32 rmii_mode = readl(fep->hwp + FEC_R_CNTRL) & (1 << 8);
+	u32 rmii_mode = readl(fep->hwp + FEC_R_CNTRL) & FEC_RCR_RMII;
 	u32 val;
 
 	/* We cannot expect a graceful transmit stop without link !!! */
@@ -1208,7 +1252,7 @@
 		if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES) {
 			writel(0, fep->hwp + FEC_ECNTRL);
 		} else {
-			writel(1, fep->hwp + FEC_ECNTRL);
+			writel(FEC_ECR_RESET, fep->hwp + FEC_ECNTRL);
 			udelay(10);
 		}
 		writel(FEC_DEFAULT_IMASK, fep->hwp + FEC_IMASK);
@@ -1224,11 +1268,16 @@
 	/* We have to keep ENET enabled to have MII interrupt stay working */
 	if (fep->quirks & FEC_QUIRK_ENET_MAC &&
 		!(fep->wol_flag & FEC_WOL_FLAG_SLEEP_ON)) {
-		writel(2, fep->hwp + FEC_ECNTRL);
+		writel(FEC_ECR_ETHEREN, fep->hwp + FEC_ECNTRL);
 		writel(rmii_mode, fep->hwp + FEC_R_CNTRL);
 	}
-}
 
+	if (fep->bufdesc_ex) {
+		val = readl(fep->hwp + FEC_ECNTRL);
+		val |= FEC_ECR_EN1588;
+		writel(val, fep->hwp + FEC_ECNTRL);
+	}
+}
 
 static void
 fec_timeout(struct net_device *ndev, unsigned int txqueue)
@@ -1480,7 +1529,7 @@
 			break;
 		pkt_received++;
 
-		writel(FEC_ENET_RXF, fep->hwp + FEC_IEVENT);
+		writel(FEC_ENET_RXF_GET(queue_id), fep->hwp + FEC_IEVENT);
 
 		/* Check for errors. */
 		status ^= BD_ENET_RX_LAST;
@@ -1813,6 +1862,7 @@
 
 		/* if any of the above changed restart the FEC */
 		if (status_change) {
+			netif_stop_queue(ndev);
 			napi_disable(&fep->napi);
 			netif_tx_lock_bh(ndev);
 			fec_restart(ndev);
@@ -1822,6 +1872,7 @@
 		}
 	} else {
 		if (fep->link) {
+			netif_stop_queue(ndev);
 			napi_disable(&fep->napi);
 			netif_tx_lock_bh(ndev);
 			fec_stop(ndev);
@@ -2130,8 +2181,6 @@
 	fep->link = 0;
 	fep->full_duplex = 0;
 
-	phy_dev->mac_managed_pm = 1;
-
 	phy_attached_info(phy_dev);
 
 	return 0;
@@ -2143,10 +2192,12 @@
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct fec_enet_private *fep = netdev_priv(ndev);
 	bool suppress_preamble = false;
+	struct phy_device *phydev;
 	struct device_node *node;
 	int err = -ENXIO;
 	u32 mii_speed, holdtime;
 	u32 bus_freq;
+	int addr;
 
 	/*
 	 * The i.MX28 dual fec interfaces are not equal.
@@ -2256,6 +2307,13 @@
 		goto err_out_free_mdiobus;
 	of_node_put(node);
 
+	/* find all the PHY devices on the bus and set mac_managed_pm to true */
+	for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
+		phydev = mdiobus_get_phy(fep->mii_bus, addr);
+		if (phydev)
+			phydev->mac_managed_pm = true;
+	}
+
 	mii_cnt++;
 
 	/* save fec0 mii_bus */
@@ -2336,6 +2394,31 @@
 	IEEE_R_DROP, IEEE_R_FRAME_OK, IEEE_R_CRC, IEEE_R_ALIGN, IEEE_R_MACERR,
 	IEEE_R_FDXFC, IEEE_R_OCTETS_OK
 };
+/* for i.MX6ul */
+static u32 fec_enet_register_offset_6ul[] = {
+	FEC_IEVENT, FEC_IMASK, FEC_R_DES_ACTIVE_0, FEC_X_DES_ACTIVE_0,
+	FEC_ECNTRL, FEC_MII_DATA, FEC_MII_SPEED, FEC_MIB_CTRLSTAT, FEC_R_CNTRL,
+	FEC_X_CNTRL, FEC_ADDR_LOW, FEC_ADDR_HIGH, FEC_OPD, FEC_TXIC0, FEC_RXIC0,
+	FEC_HASH_TABLE_HIGH, FEC_HASH_TABLE_LOW, FEC_GRP_HASH_TABLE_HIGH,
+	FEC_GRP_HASH_TABLE_LOW, FEC_X_WMRK, FEC_R_DES_START_0,
+	FEC_X_DES_START_0, FEC_R_BUFF_SIZE_0, FEC_R_FIFO_RSFL, FEC_R_FIFO_RSEM,
+	FEC_R_FIFO_RAEM, FEC_R_FIFO_RAFL, FEC_RACC,
+	RMON_T_DROP, RMON_T_PACKETS, RMON_T_BC_PKT, RMON_T_MC_PKT,
+	RMON_T_CRC_ALIGN, RMON_T_UNDERSIZE, RMON_T_OVERSIZE, RMON_T_FRAG,
+	RMON_T_JAB, RMON_T_COL, RMON_T_P64, RMON_T_P65TO127, RMON_T_P128TO255,
+	RMON_T_P256TO511, RMON_T_P512TO1023, RMON_T_P1024TO2047,
+	RMON_T_P_GTE2048, RMON_T_OCTETS,
+	IEEE_T_DROP, IEEE_T_FRAME_OK, IEEE_T_1COL, IEEE_T_MCOL, IEEE_T_DEF,
+	IEEE_T_LCOL, IEEE_T_EXCOL, IEEE_T_MACERR, IEEE_T_CSERR, IEEE_T_SQE,
+	IEEE_T_FDXFC, IEEE_T_OCTETS_OK,
+	RMON_R_PACKETS, RMON_R_BC_PKT, RMON_R_MC_PKT, RMON_R_CRC_ALIGN,
+	RMON_R_UNDERSIZE, RMON_R_OVERSIZE, RMON_R_FRAG, RMON_R_JAB,
+	RMON_R_RESVD_O, RMON_R_P64, RMON_R_P65TO127, RMON_R_P128TO255,
+	RMON_R_P256TO511, RMON_R_P512TO1023, RMON_R_P1024TO2047,
+	RMON_R_P_GTE2048, RMON_R_OCTETS,
+	IEEE_R_DROP, IEEE_R_FRAME_OK, IEEE_R_CRC, IEEE_R_ALIGN, IEEE_R_MACERR,
+	IEEE_R_FDXFC, IEEE_R_OCTETS_OK
+};
 #else
 static __u32 fec_enet_register_version = 1;
 static u32 fec_enet_register_offset[] = {
@@ -2360,7 +2443,24 @@
 	u32 *buf = (u32 *)regbuf;
 	u32 i, off;
 	int ret;
+#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
+	defined(CONFIG_M520x) || defined(CONFIG_M532x) || defined(CONFIG_ARM) || \
+	defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)
+	u32 *reg_list;
+	u32 reg_cnt;
 
+	if (!of_machine_is_compatible("fsl,imx6ul")) {
+		reg_list = fec_enet_register_offset;
+		reg_cnt = ARRAY_SIZE(fec_enet_register_offset);
+	} else {
+		reg_list = fec_enet_register_offset_6ul;
+		reg_cnt = ARRAY_SIZE(fec_enet_register_offset_6ul);
+	}
+#else
+	/* coldfire */
+	static u32 *reg_list = fec_enet_register_offset;
+	static const u32 reg_cnt = ARRAY_SIZE(fec_enet_register_offset);
+#endif
 	ret = pm_runtime_resume_and_get(dev);
 	if (ret < 0)
 		return;
@@ -2369,8 +2469,8 @@
 
 	memset(buf, 0, regs->len);
 
-	for (i = 0; i < ARRAY_SIZE(fec_enet_register_offset); i++) {
-		off = fec_enet_register_offset[i];
+	for (i = 0; i < reg_cnt; i++) {
+		off = reg_list[i];
 
 		if ((off == FEC_R_BOUND || off == FEC_R_FSTART) &&
 		    !(fep->quirks & FEC_QUIRK_HAS_FRREG))
@@ -2718,19 +2818,6 @@
 	return 0;
 }
 
-static void fec_enet_itr_coal_init(struct net_device *ndev)
-{
-	struct ethtool_coalesce ec;
-
-	ec.rx_coalesce_usecs = FEC_ITR_ICTT_DEFAULT;
-	ec.rx_max_coalesced_frames = FEC_ITR_ICFT_DEFAULT;
-
-	ec.tx_coalesce_usecs = FEC_ITR_ICTT_DEFAULT;
-	ec.tx_max_coalesced_frames = FEC_ITR_ICFT_DEFAULT;
-
-	fec_enet_set_coalesce(ndev, &ec, NULL, NULL);
-}
-
 static int fec_enet_get_tunable(struct net_device *netdev,
 				const struct ethtool_tunable *tuna,
 				void *data)
@@ -3345,29 +3432,6 @@
 	return 0;
 }
 
-#ifdef CONFIG_NET_POLL_CONTROLLER
-/**
- * fec_poll_controller - FEC Poll controller function
- * @dev: The FEC network adapter
- *
- * Polled functionality used by netconsole and others in non interrupt mode
- *
- */
-static void fec_poll_controller(struct net_device *dev)
-{
-	int i;
-	struct fec_enet_private *fep = netdev_priv(dev);
-
-	for (i = 0; i < FEC_IRQ_NUM; i++) {
-		if (fep->irq[i] > 0) {
-			disable_irq(fep->irq[i]);
-			fec_enet_interrupt(fep->irq[i], dev);
-			enable_irq(fep->irq[i]);
-		}
-	}
-}
-#endif
-
 static inline void fec_enet_set_netdev_features(struct net_device *netdev,
 	netdev_features_t features)
 {
@@ -3407,31 +3471,26 @@
 	return 0;
 }
 
-static u16 fec_enet_get_raw_vlan_tci(struct sk_buff *skb)
-{
-	struct vlan_ethhdr *vhdr;
-	unsigned short vlan_TCI = 0;
-
-	if (skb->protocol == htons(ETH_P_ALL)) {
-		vhdr = (struct vlan_ethhdr *)(skb->data);
-		vlan_TCI = ntohs(vhdr->h_vlan_TCI);
-	}
-
-	return vlan_TCI;
-}
-
 static u16 fec_enet_select_queue(struct net_device *ndev, struct sk_buff *skb,
 				 struct net_device *sb_dev)
 {
 	struct fec_enet_private *fep = netdev_priv(ndev);
-	u16 vlan_tag;
+	u16 vlan_tag = 0;
 
 	if (!(fep->quirks & FEC_QUIRK_HAS_AVB))
 		return netdev_pick_tx(ndev, skb, NULL);
 
-	vlan_tag = fec_enet_get_raw_vlan_tci(skb);
-	if (!vlan_tag)
+	/* VLAN is present in the payload.*/
+	if (eth_type_vlan(skb->protocol)) {
+		struct vlan_ethhdr *vhdr = skb_vlan_eth_hdr(skb);
+
+		vlan_tag = ntohs(vhdr->h_vlan_TCI);
+	/*  VLAN is present in the skb but not yet pushed in the payload.*/
+	} else if (skb_vlan_tag_present(skb)) {
+		vlan_tag = skb->vlan_tci;
+	} else {
 		return vlan_tag;
+	}
 
 	return fec_enet_vlan_pri_to_queue[vlan_tag >> 13];
 }
@@ -3446,9 +3505,6 @@
 	.ndo_tx_timeout		= fec_timeout,
 	.ndo_set_mac_address	= fec_set_mac_address,
 	.ndo_eth_ioctl		= fec_enet_ioctl,
-#ifdef CONFIG_NET_POLL_CONTROLLER
-	.ndo_poll_controller	= fec_poll_controller,
-#endif
 	.ndo_set_features	= fec_set_features,
 };
 
@@ -3484,6 +3540,10 @@
 	fep->rx_align = 0x3;
 	fep->tx_align = 0x3;
 #endif
+	fep->rx_pkts_itr = FEC_ITR_ICFT_DEFAULT;
+	fep->tx_pkts_itr = FEC_ITR_ICFT_DEFAULT;
+	fep->rx_time_itr = FEC_ITR_ICTT_DEFAULT;
+	fep->tx_time_itr = FEC_ITR_ICTT_DEFAULT;
 
 	/* Check mask of the streaming and coherent API */
 	ret = dma_set_mask_and_coherent(&fep->pdev->dev, DMA_BIT_MASK(32));
@@ -3590,6 +3650,14 @@
 	return ret;
 }
 
+static void fec_enet_deinit(struct net_device *ndev)
+{
+	struct fec_enet_private *fep = netdev_priv(ndev);
+
+	netif_napi_del(&fep->napi);
+	fec_enet_free_queue(ndev);
+}
+
 #ifdef CONFIG_OF
 static int fec_reset_phy(struct platform_device *pdev)
 {
@@ -3726,7 +3794,7 @@
 					 ARRAY_SIZE(out_val));
 	if (ret) {
 		dev_dbg(&fep->pdev->dev, "no stop mode property\n");
-		return ret;
+		goto out;
 	}
 
 	fep->stop_gpr.gpr = syscon_node_to_regmap(gpr_np);
@@ -3986,6 +4054,7 @@
 	fec_enet_mii_remove(fep);
 failed_mii_init:
 failed_irq:
+	fec_enet_deinit(ndev);
 failed_init:
 	fec_ptp_stop(pdev);
 failed_reset:
@@ -4021,9 +4090,11 @@
 	struct device_node *np = pdev->dev.of_node;
 	int ret;
 
-	ret = pm_runtime_resume_and_get(&pdev->dev);
+	ret = pm_runtime_get_sync(&pdev->dev);
 	if (ret < 0)
-		return ret;
+		dev_err(&pdev->dev,
+			"Failed to resume device in remove callback (%pe)\n",
+			ERR_PTR(ret));
 
 	cancel_work_sync(&fep->tx_timeout_work);
 	fec_ptp_stop(pdev);
@@ -4036,11 +4107,17 @@
 		of_phy_deregister_fixed_link(np);
 	of_node_put(fep->phy_node);
 
-	clk_disable_unprepare(fep->clk_ahb);
-	clk_disable_unprepare(fep->clk_ipg);
+	/* After pm_runtime_get_sync() failed, the clks are still off, so skip
+	 * disabling them again.
+	 */
+	if (ret >= 0) {
+		clk_disable_unprepare(fep->clk_ahb);
+		clk_disable_unprepare(fep->clk_ipg);
+	}
 	pm_runtime_put_noidle(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 
+	fec_enet_deinit(ndev);
 	free_netdev(ndev);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fec_mpc52xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fec_mpc52xx.c
@@ -890,7 +890,7 @@
 	 *
 	 * First try to read MAC address from DT
 	 */
-	rv = of_get_mac_address(np, ndev->dev_addr);
+	rv = of_get_ethdev_address(np, ndev);
 	if (rv) {
 		struct mpc52xx_fec __iomem *fec = priv->fec;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fec_mpc52xx_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fec_mpc52xx_phy.c
@@ -92,7 +92,7 @@
 		goto out_free;
 	}
 
-	snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%pa", &res.start);
 	bus->priv = priv;
 
 	bus->parent = dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fec_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fec_ptp.c
@@ -103,14 +103,13 @@
 	u64 ns;
 	val = 0;
 
-	if (fep->pps_enable == enable)
-		return 0;
-
-	fep->pps_channel = DEFAULT_PPS_CHANNEL;
-	fep->reload_period = PPS_OUPUT_RELOAD_PERIOD;
-
 	spin_lock_irqsave(&fep->tmreg_lock, flags);
 
+	if (fep->pps_enable == enable) {
+		spin_unlock_irqrestore(&fep->tmreg_lock, flags);
+		return 0;
+	}
+
 	if (enable) {
 		/* clear capture or output compare interrupt status if have.
 		 */
@@ -136,11 +135,7 @@
 		 * NSEC_PER_SEC - ts.tv_nsec. Add the remaining nanoseconds
 		 * to current timer would be next second.
 		 */
-		tempval = readl(fep->hwp + FEC_ATIME_CTRL);
-		tempval |= FEC_T_CTRL_CAPTURE;
-		writel(tempval, fep->hwp + FEC_ATIME_CTRL);
-
-		tempval = readl(fep->hwp + FEC_ATIME);
+		tempval = fep->cc.read(&fep->cc);
 		/* Convert the ptp local counter to 1588 timestamp */
 		ns = timecounter_cyc2time(&fep->tc, tempval);
 		ts = ns_to_timespec64(ns);
@@ -445,6 +440,9 @@
 	int ret = 0;
 
 	if (rq->type == PTP_CLK_REQ_PPS) {
+		fep->pps_channel = DEFAULT_PPS_CHANNEL;
+		fep->reload_period = PPS_OUPUT_RELOAD_PERIOD;
+
 		ret = fec_ptp_enable_pps(fep, on);
 
 		return ret;
@@ -642,6 +640,9 @@
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct fec_enet_private *fep = netdev_priv(ndev);
 
+	if (fep->pps_enable)
+		fec_ptp_enable_pps(fep, 0);
+
 	cancel_delayed_work_sync(&fep->time_keep);
 	if (fep->ptp_clock)
 		ptp_clock_unregister(fep->ptp_clock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_dtsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_dtsec.c
@@ -366,7 +366,7 @@
 	cfg->maximum_frame = DEFAULT_MAXIMUM_FRAME;
 }
 
-static void set_mac_address(struct dtsec_regs __iomem *regs, u8 *adr)
+static void set_mac_address(struct dtsec_regs __iomem *regs, const u8 *adr)
 {
 	u32 tmp;
 
@@ -516,7 +516,7 @@
 
 	if (addr) {
 		MAKE_ENET_ADDR_FROM_UINT64(addr, eth_addr);
-		set_mac_address(regs, (u8 *)eth_addr);
+		set_mac_address(regs, (const u8 *)eth_addr);
 	}
 
 	/* HASH */
@@ -1022,7 +1022,7 @@
 	return 0;
 }
 
-int dtsec_modify_mac_address(struct fman_mac *dtsec, enet_addr_t *enet_addr)
+int dtsec_modify_mac_address(struct fman_mac *dtsec, const enet_addr_t *enet_addr)
 {
 	struct dtsec_regs __iomem *regs = dtsec->regs;
 	enum comm_mode mode = COMM_MODE_NONE;
@@ -1041,7 +1041,7 @@
 	 * Station address have to be swapped (big endian to little endian
 	 */
 	dtsec->addr = ENET_ADDR_TO_UINT64(*enet_addr);
-	set_mac_address(dtsec->regs, (u8 *)(*enet_addr));
+	set_mac_address(dtsec->regs, (const u8 *)(*enet_addr));
 
 	graceful_start(dtsec, mode);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_dtsec.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_dtsec.h
@@ -37,7 +37,7 @@
 
 struct fman_mac *dtsec_config(struct fman_mac_params *params);
 int dtsec_set_promiscuous(struct fman_mac *dtsec, bool new_val);
-int dtsec_modify_mac_address(struct fman_mac *dtsec, enet_addr_t *enet_addr);
+int dtsec_modify_mac_address(struct fman_mac *dtsec, const enet_addr_t *enet_addr);
 int dtsec_adjust_link(struct fman_mac *dtsec,
 		      u16 speed);
 int dtsec_restart_autoneg(struct fman_mac *dtsec);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_memac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_memac.c
@@ -354,7 +354,7 @@
 	bool allmulti_enabled;
 };
 
-static void add_addr_in_paddr(struct memac_regs __iomem *regs, u8 *adr,
+static void add_addr_in_paddr(struct memac_regs __iomem *regs, const u8 *adr,
 			      u8 paddr_num)
 {
 	u32 tmp0, tmp1;
@@ -897,12 +897,12 @@
 	return 0;
 }
 
-int memac_modify_mac_address(struct fman_mac *memac, enet_addr_t *enet_addr)
+int memac_modify_mac_address(struct fman_mac *memac, const enet_addr_t *enet_addr)
 {
 	if (!is_init_done(memac->memac_drv_param))
 		return -EINVAL;
 
-	add_addr_in_paddr(memac->regs, (u8 *)(*enet_addr), 0);
+	add_addr_in_paddr(memac->regs, (const u8 *)(*enet_addr), 0);
 
 	return 0;
 }
@@ -1058,7 +1058,7 @@
 	/* MAC Address */
 	if (memac->addr != 0) {
 		MAKE_ENET_ADDR_FROM_UINT64(memac->addr, eth_addr);
-		add_addr_in_paddr(memac->regs, (u8 *)eth_addr, 0);
+		add_addr_in_paddr(memac->regs, (const u8 *)eth_addr, 0);
 	}
 
 	fixed_link = memac_drv_param->fixed_link;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_memac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_memac.h
@@ -40,7 +40,7 @@
 
 struct fman_mac *memac_config(struct fman_mac_params *params);
 int memac_set_promiscuous(struct fman_mac *memac, bool new_val);
-int memac_modify_mac_address(struct fman_mac *memac, enet_addr_t *enet_addr);
+int memac_modify_mac_address(struct fman_mac *memac, const enet_addr_t *enet_addr);
 int memac_adjust_link(struct fman_mac *memac, u16 speed);
 int memac_cfg_max_frame_len(struct fman_mac *memac, u16 new_val);
 int memac_cfg_reset_on_init(struct fman_mac *memac, bool enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_port.c
@@ -1805,7 +1805,7 @@
 	fman = dev_get_drvdata(&fm_pdev->dev);
 	if (!fman) {
 		err = -EINVAL;
-		goto return_err;
+		goto put_device;
 	}
 
 	err = of_property_read_u32(port_node, "cell-index", &val);
@@ -1813,7 +1813,7 @@
 		dev_err(port->dev, "%s: reading cell-index for %pOF failed\n",
 			__func__, port_node);
 		err = -EINVAL;
-		goto return_err;
+		goto put_device;
 	}
 	port_id = (u8)val;
 	port->dts_params.id = port_id;
@@ -1847,7 +1847,7 @@
 	}  else {
 		dev_err(port->dev, "%s: Illegal port type\n", __func__);
 		err = -EINVAL;
-		goto return_err;
+		goto put_device;
 	}
 
 	port->dts_params.type = port_type;
@@ -1861,7 +1861,7 @@
 			dev_err(port->dev, "%s: incorrect qman-channel-id\n",
 				__func__);
 			err = -EINVAL;
-			goto return_err;
+			goto put_device;
 		}
 		port->dts_params.qman_channel_id = qman_channel_id;
 	}
@@ -1871,7 +1871,7 @@
 		dev_err(port->dev, "%s: of_address_to_resource() failed\n",
 			__func__);
 		err = -ENOMEM;
-		goto return_err;
+		goto put_device;
 	}
 
 	port->dts_params.fman = fman;
@@ -1896,6 +1896,8 @@
 
 	return 0;
 
+put_device:
+	put_device(&fm_pdev->dev);
 return_err:
 	of_node_put(port_node);
 free_port:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_tgec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_tgec.c
@@ -221,7 +221,7 @@
 	bool allmulti_enabled;
 };
 
-static void set_mac_address(struct tgec_regs __iomem *regs, u8 *adr)
+static void set_mac_address(struct tgec_regs __iomem *regs, const u8 *adr)
 {
 	u32 tmp0, tmp1;
 
@@ -514,13 +514,13 @@
 	return 0;
 }
 
-int tgec_modify_mac_address(struct fman_mac *tgec, enet_addr_t *p_enet_addr)
+int tgec_modify_mac_address(struct fman_mac *tgec, const enet_addr_t *p_enet_addr)
 {
 	if (!is_init_done(tgec->cfg))
 		return -EINVAL;
 
 	tgec->addr = ENET_ADDR_TO_UINT64(*p_enet_addr);
-	set_mac_address(tgec->regs, (u8 *)(*p_enet_addr));
+	set_mac_address(tgec->regs, (const u8 *)(*p_enet_addr));
 
 	return 0;
 }
@@ -704,7 +704,7 @@
 
 	if (tgec->addr) {
 		MAKE_ENET_ADDR_FROM_UINT64(tgec->addr, eth_addr);
-		set_mac_address(tgec->regs, (u8 *)eth_addr);
+		set_mac_address(tgec->regs, (const u8 *)eth_addr);
 	}
 
 	/* interrupts */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/fman_tgec.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/fman_tgec.h
@@ -37,7 +37,7 @@
 
 struct fman_mac *tgec_config(struct fman_mac_params *params);
 int tgec_set_promiscuous(struct fman_mac *tgec, bool new_val);
-int tgec_modify_mac_address(struct fman_mac *tgec, enet_addr_t *enet_addr);
+int tgec_modify_mac_address(struct fman_mac *tgec, const enet_addr_t *enet_addr);
 int tgec_cfg_max_frame_len(struct fman_mac *tgec, u16 new_val);
 int tgec_enable(struct fman_mac *tgec, enum comm_mode mode);
 int tgec_disable(struct fman_mac *tgec, enum comm_mode mode);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/mac.c
@@ -94,14 +94,17 @@
 		__func__, ex);
 }
 
-static void set_fman_mac_params(struct mac_device *mac_dev,
-				struct fman_mac_params *params)
+static int set_fman_mac_params(struct mac_device *mac_dev,
+			       struct fman_mac_params *params)
 {
 	struct mac_priv_s *priv = mac_dev->priv;
 
 	params->base_addr = (typeof(params->base_addr))
 		devm_ioremap(priv->dev, mac_dev->res->start,
 			     resource_size(mac_dev->res));
+	if (!params->base_addr)
+		return -ENOMEM;
+
 	memcpy(&params->addr, mac_dev->addr, sizeof(mac_dev->addr));
 	params->max_speed	= priv->max_speed;
 	params->phy_if		= mac_dev->phy_if;
@@ -112,6 +115,8 @@
 	params->event_cb	= mac_exception;
 	params->dev_id		= mac_dev;
 	params->internal_phy_node = priv->internal_phy_node;
+
+	return 0;
 }
 
 static int tgec_initialization(struct mac_device *mac_dev)
@@ -123,7 +128,9 @@
 
 	priv = mac_dev->priv;
 
-	set_fman_mac_params(mac_dev, &params);
+	err = set_fman_mac_params(mac_dev, &params);
+	if (err)
+		goto _return;
 
 	mac_dev->fman_mac = tgec_config(&params);
 	if (!mac_dev->fman_mac) {
@@ -169,7 +176,9 @@
 
 	priv = mac_dev->priv;
 
-	set_fman_mac_params(mac_dev, &params);
+	err = set_fman_mac_params(mac_dev, &params);
+	if (err)
+		goto _return;
 
 	mac_dev->fman_mac = dtsec_config(&params);
 	if (!mac_dev->fman_mac) {
@@ -218,7 +227,9 @@
 
 	priv = mac_dev->priv;
 
-	set_fman_mac_params(mac_dev, &params);
+	err = set_fman_mac_params(mac_dev, &params);
+	if (err)
+		goto _return;
 
 	if (priv->max_speed == SPEED_10000)
 		params.phy_if = PHY_INTERFACE_MODE_XGMII;
@@ -871,12 +882,21 @@
 	return err;
 }
 
+static int mac_remove(struct platform_device *pdev)
+{
+	struct mac_device *mac_dev = platform_get_drvdata(pdev);
+
+	platform_device_unregister(mac_dev->priv->eth_dev);
+	return 0;
+}
+
 static struct platform_driver mac_driver = {
 	.driver = {
 		.name		= KBUILD_MODNAME,
 		.of_match_table	= mac_match,
 	},
 	.probe		= mac_probe,
+	.remove		= mac_remove,
 };
 
 builtin_platform_driver(mac_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fman/mac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fman/mac.h
@@ -66,7 +66,7 @@
 	int (*stop)(struct mac_device *mac_dev);
 	void (*adjust_link)(struct mac_device *mac_dev);
 	int (*set_promisc)(struct fman_mac *mac_dev, bool enable);
-	int (*change_addr)(struct fman_mac *mac_dev, enet_addr_t *enet_addr);
+	int (*change_addr)(struct fman_mac *mac_dev, const enet_addr_t *enet_addr);
 	int (*set_allmulti)(struct fman_mac *mac_dev, bool enable);
 	int (*set_tstamp)(struct fman_mac *mac_dev, bool enable);
 	int (*set_multi)(struct net_device *net_dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
@@ -1005,7 +1005,7 @@
 	spin_lock_init(&fep->lock);
 	spin_lock_init(&fep->tx_lock);
 
-	of_get_mac_address(ofdev->dev.of_node, ndev->dev_addr);
+	of_get_ethdev_address(ofdev->dev.of_node, ndev);
 
 	ret = fep->ops->allocate_bd(ndev);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fs_enet/mac-fec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fs_enet/mac-fec.c
@@ -98,7 +98,7 @@
 		return -EINVAL;
 
 	fep->fec.fecp = of_iomap(ofdev->dev.of_node, 0);
-	if (!fep->fcc.fccp)
+	if (!fep->fec.fecp)
 		return -EINVAL;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c
@@ -126,7 +126,7 @@
 	 * we get is an int, and the odds of multiple bitbang mdio buses
 	 * is low enough that it's not worth going too crazy.
 	 */
-	snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%pa", &res.start);
 
 	data = of_get_property(np, "fsl,mdio-pin", &len);
 	if (!data || len != 4)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/gianfar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/gianfar.c
@@ -753,7 +753,7 @@
 	if (stash_len || stash_idx)
 		priv->device_flags |= FSL_GIANFAR_DEV_HAS_BUF_STASHING;
 
-	err = of_get_mac_address(np, dev->dev_addr);
+	err = of_get_ethdev_address(np, dev);
 	if (err) {
 		eth_hw_addr_random(dev);
 		dev_info(&ofdev->dev, "Using random MAC address: %pM\n", dev->dev_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/gianfar_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/gianfar_ethtool.c
@@ -1460,6 +1460,7 @@
 	ptp_node = of_find_compatible_node(NULL, NULL, "fsl,etsec-ptp");
 	if (ptp_node) {
 		ptp_dev = of_find_device_by_node(ptp_node);
+		of_node_put(ptp_node);
 		if (ptp_dev)
 			ptp = platform_get_drvdata(ptp_dev);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/ucc_geth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/ucc_geth.c
@@ -3731,7 +3731,7 @@
 		goto err_free_netdev;
 	}
 
-	of_get_mac_address(np, dev->dev_addr);
+	of_get_ethdev_address(np, dev);
 
 	ugeth->ug_info = ug_info;
 	ugeth->dev = device;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/freescale/xgmac_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/freescale/xgmac_mdio.c
@@ -52,6 +52,7 @@
 struct mdio_fsl_priv {
 	struct	tgec_mdio_controller __iomem *mdio_base;
 	bool	is_little_endian;
+	bool	has_a009885;
 	bool	has_a011043;
 };
 
@@ -187,10 +188,10 @@
 {
 	struct mdio_fsl_priv *priv = (struct mdio_fsl_priv *)bus->priv;
 	struct tgec_mdio_controller __iomem *regs = priv->mdio_base;
+	unsigned long flags;
 	uint16_t dev_addr;
 	uint32_t mdio_stat;
 	uint32_t mdio_ctl;
-	uint16_t value;
 	int ret;
 	bool endian = priv->is_little_endian;
 
@@ -222,12 +223,18 @@
 			return ret;
 	}
 
+	if (priv->has_a009885)
+		/* Once the operation completes, i.e. MDIO_STAT_BSY clears, we
+		 * must read back the data register within 16 MDC cycles.
+		 */
+		local_irq_save(flags);
+
 	/* Initiate the read */
 	xgmac_write32(mdio_ctl | MDIO_CTL_READ, &regs->mdio_ctl, endian);
 
 	ret = xgmac_wait_until_done(&bus->dev, regs, endian);
 	if (ret)
-		return ret;
+		goto irq_restore;
 
 	/* Return all Fs if nothing was there */
 	if ((xgmac_read32(&regs->mdio_stat, endian) & MDIO_STAT_RD_ER) &&
@@ -235,13 +242,17 @@
 		dev_dbg(&bus->dev,
 			"Error while reading PHY%d reg at %d.%hhu\n",
 			phy_id, dev_addr, regnum);
-		return 0xffff;
+		ret = 0xffff;
+	} else {
+		ret = xgmac_read32(&regs->mdio_data, endian) & 0xffff;
+		dev_dbg(&bus->dev, "read %04x\n", ret);
 	}
 
-	value = xgmac_read32(&regs->mdio_data, endian) & 0xffff;
-	dev_dbg(&bus->dev, "read %04x\n", value);
+irq_restore:
+	if (priv->has_a009885)
+		local_irq_restore(flags);
 
-	return value;
+	return ret;
 }
 
 static int xgmac_mdio_probe(struct platform_device *pdev)
@@ -288,6 +299,8 @@
 	priv->is_little_endian = device_property_read_bool(&pdev->dev,
 							   "little-endian");
 
+	priv->has_a009885 = device_property_read_bool(&pdev->dev,
+						      "fsl,erratum-a009885");
 	priv->has_a011043 = device_property_read_bool(&pdev->dev,
 						      "fsl,erratum-a011043");
 
@@ -319,9 +332,10 @@
 static int xgmac_mdio_remove(struct platform_device *pdev)
 {
 	struct mii_bus *bus = platform_get_drvdata(pdev);
+	struct mdio_fsl_priv *priv = bus->priv;
 
 	mdiobus_unregister(bus);
-	iounmap(bus->priv);
+	iounmap(priv->mdio_base);
 	mdiobus_free(bus);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve.h
@@ -8,6 +8,7 @@
 #define _GVE_H_
 
 #include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
 #include <linux/netdevice.h>
 #include <linux/pci.h>
 #include <linux/u64_stats_sync.h>
@@ -30,7 +31,7 @@
 #define GVE_MIN_MSIX 3
 
 /* Numbers of gve tx/rx stats in stats report. */
-#define GVE_TX_STATS_REPORT_NUM	5
+#define GVE_TX_STATS_REPORT_NUM	6
 #define GVE_RX_STATS_REPORT_NUM	2
 
 /* Interval to schedule a stats report update, 20000ms. */
@@ -40,12 +41,18 @@
 #define NIC_TX_STATS_REPORT_NUM	0
 #define NIC_RX_STATS_REPORT_NUM	4
 
+#define GVE_ADMINQ_BUFFER_SIZE 4096
+
 #define GVE_DATA_SLOT_ADDR_PAGE_MASK (~(PAGE_SIZE - 1))
 
 /* PTYPEs are always 10 bits. */
 #define GVE_NUM_PTYPES	1024
 
-#define GVE_RX_BUFFER_SIZE_DQO 2048
+#define GVE_DEFAULT_RX_BUFFER_SIZE 2048
+
+#define GVE_DEFAULT_RX_BUFFER_OFFSET 2048
+
+#define GVE_GQ_TX_MIN_PKT_DESC_BYTES 182
 
 /* Each slot in the desc ring has a 1:1 mapping to a slot in the data ring */
 struct gve_rx_desc_queue {
@@ -142,6 +149,15 @@
 	s16 tail;
 };
 
+/* A single received packet split across multiple buffers may be
+ * reconstructed using the information in this structure.
+ */
+struct gve_rx_ctx {
+	/* head and tail of skb chain for the current packet or NULL if none */
+	struct sk_buff *skb_head;
+	struct sk_buff *skb_tail;
+};
+
 /* Contains datapath state used to represent an RX queue. */
 struct gve_rx_ring {
 	struct gve_priv *gve;
@@ -206,9 +222,7 @@
 	dma_addr_t q_resources_bus; /* dma address for the queue resources */
 	struct u64_stats_sync statss; /* sync stats for 32bit archs */
 
-	/* head and tail of skb chain for the current packet or NULL if none */
-	struct sk_buff *skb_head;
-	struct sk_buff *skb_tail;
+	struct gve_rx_ctx ctx; /* Info for packet currently being processed in this ring. */
 };
 
 /* A TX desc ring entry */
@@ -224,11 +238,6 @@
 	u32 iov_padding; /* padding associated with this segment */
 };
 
-struct gve_tx_dma_buf {
-	DEFINE_DMA_UNMAP_ADDR(dma);
-	DEFINE_DMA_UNMAP_LEN(len);
-};
-
 /* Tracks the memory in the fifo occupied by the skb. Mapped 1:1 to a desc
  * ring entry but only used for a pkt_desc not a seg_desc
  */
@@ -236,7 +245,10 @@
 	struct sk_buff *skb; /* skb for this pkt */
 	union {
 		struct gve_tx_iovec iov[GVE_TX_MAX_IOVEC]; /* segments of this pkt */
-		struct gve_tx_dma_buf buf;
+		struct {
+			DEFINE_DMA_UNMAP_ADDR(dma);
+			DEFINE_DMA_UNMAP_LEN(len);
+		};
 	};
 };
 
@@ -280,7 +292,8 @@
 	 * All others correspond to `skb`'s frags and should be unmapped with
 	 * `dma_unmap_page`.
 	 */
-	struct gve_tx_dma_buf bufs[MAX_SKB_FRAGS + 1];
+	DEFINE_DMA_UNMAP_ADDR(dma[MAX_SKB_FRAGS + 1]);
+	DEFINE_DMA_UNMAP_LEN(len[MAX_SKB_FRAGS + 1]);
 	u16 num_bufs;
 
 	/* Linked list index to next element in the list, or -1 if none */
@@ -414,7 +427,9 @@
 	u32 q_num ____cacheline_aligned; /* queue idx */
 	u32 stop_queue; /* count of queue stops */
 	u32 wake_queue; /* count of queue wakes */
+	u32 queue_timeout; /* count of queue timeouts */
 	u32 ntfy_id; /* notification block index */
+	u32 last_kick_msec; /* Last time the queue was kicked */
 	dma_addr_t bus; /* dma address of the descr ring */
 	dma_addr_t q_resources_bus; /* dma address of the queue resources */
 	dma_addr_t complq_bus_dqo; /* dma address of the dqo.compl_ring */
@@ -509,6 +524,7 @@
 	/* Admin queue - see gve_adminq.h*/
 	union gve_adminq_command *adminq;
 	dma_addr_t adminq_bus_addr;
+	struct dma_pool *adminq_pool;
 	u32 adminq_mask; /* masks prod_cnt to adminq size */
 	u32 adminq_prod_cnt; /* free-running count of AQ cmds executed */
 	u32 adminq_cmd_fail; /* free-running count of AQ cmds failed */
@@ -814,7 +830,7 @@
 /* buffers */
 int gve_alloc_page(struct gve_priv *priv, struct device *dev,
 		   struct page **page, dma_addr_t *dma,
-		   enum dma_data_direction);
+		   enum dma_data_direction, gfp_t gfp_flags);
 void gve_free_page(struct device *dev, struct page *page, dma_addr_t dma,
 		   enum dma_data_direction);
 /* tx handling */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_adminq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_adminq.c
@@ -155,12 +155,19 @@
 
 int gve_adminq_alloc(struct device *dev, struct gve_priv *priv)
 {
-	priv->adminq = dma_alloc_coherent(dev, PAGE_SIZE,
-					  &priv->adminq_bus_addr, GFP_KERNEL);
-	if (unlikely(!priv->adminq))
+	priv->adminq_pool = dma_pool_create("adminq_pool", dev,
+					    GVE_ADMINQ_BUFFER_SIZE, 0, 0);
+	if (unlikely(!priv->adminq_pool))
 		return -ENOMEM;
+	priv->adminq = dma_pool_alloc(priv->adminq_pool, GFP_KERNEL,
+				      &priv->adminq_bus_addr);
+	if (unlikely(!priv->adminq)) {
+		dma_pool_destroy(priv->adminq_pool);
+		return -ENOMEM;
+	}
 
-	priv->adminq_mask = (PAGE_SIZE / sizeof(union gve_adminq_command)) - 1;
+	priv->adminq_mask =
+		(GVE_ADMINQ_BUFFER_SIZE / sizeof(union gve_adminq_command)) - 1;
 	priv->adminq_prod_cnt = 0;
 	priv->adminq_cmd_fail = 0;
 	priv->adminq_timeouts = 0;
@@ -179,9 +186,20 @@
 	priv->adminq_get_ptype_map_cnt = 0;
 
 	/* Setup Admin queue with the device */
-	iowrite32be(priv->adminq_bus_addr / PAGE_SIZE,
-		    &priv->reg_bar0->adminq_pfn);
-
+	if (priv->pdev->revision < 0x1) {
+		iowrite32be(priv->adminq_bus_addr / PAGE_SIZE,
+			    &priv->reg_bar0->adminq_pfn);
+	} else {
+		iowrite16be(GVE_ADMINQ_BUFFER_SIZE,
+			    &priv->reg_bar0->adminq_length);
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+		iowrite32be(priv->adminq_bus_addr >> 32,
+			    &priv->reg_bar0->adminq_base_address_hi);
+#endif
+		iowrite32be(priv->adminq_bus_addr,
+			    &priv->reg_bar0->adminq_base_address_lo);
+		iowrite32be(GVE_DRIVER_STATUS_RUN_MASK, &priv->reg_bar0->driver_status);
+	}
 	gve_set_admin_queue_ok(priv);
 	return 0;
 }
@@ -191,16 +209,27 @@
 	int i = 0;
 
 	/* Tell the device the adminq is leaving */
-	iowrite32be(0x0, &priv->reg_bar0->adminq_pfn);
-	while (ioread32be(&priv->reg_bar0->adminq_pfn)) {
-		/* If this is reached the device is unrecoverable and still
-		 * holding memory. Continue looping to avoid memory corruption,
-		 * but WARN so it is visible what is going on.
-		 */
-		if (i == GVE_MAX_ADMINQ_RELEASE_CHECK)
-			WARN(1, "Unrecoverable platform error!");
-		i++;
-		msleep(GVE_ADMINQ_SLEEP_LEN);
+	if (priv->pdev->revision < 0x1) {
+		iowrite32be(0x0, &priv->reg_bar0->adminq_pfn);
+		while (ioread32be(&priv->reg_bar0->adminq_pfn)) {
+			/* If this is reached the device is unrecoverable and still
+			 * holding memory. Continue looping to avoid memory corruption,
+			 * but WARN so it is visible what is going on.
+			 */
+			if (i == GVE_MAX_ADMINQ_RELEASE_CHECK)
+				WARN(1, "Unrecoverable platform error!");
+			i++;
+			msleep(GVE_ADMINQ_SLEEP_LEN);
+		}
+	} else {
+		iowrite32be(GVE_DRIVER_STATUS_RESET_MASK, &priv->reg_bar0->driver_status);
+		while (!(ioread32be(&priv->reg_bar0->device_status)
+				& GVE_DEVICE_STATUS_DEVICE_IS_RESET)) {
+			if (i == GVE_MAX_ADMINQ_RELEASE_CHECK)
+				WARN(1, "Unrecoverable platform error!");
+			i++;
+			msleep(GVE_ADMINQ_SLEEP_LEN);
+		}
 	}
 	gve_clear_device_rings_ok(priv);
 	gve_clear_device_resources_ok(priv);
@@ -212,7 +241,8 @@
 	if (!gve_get_admin_queue_ok(priv))
 		return;
 	gve_adminq_release(priv);
-	dma_free_coherent(dev, PAGE_SIZE, priv->adminq, priv->adminq_bus_addr);
+	dma_pool_free(priv->adminq_pool, priv->adminq, priv->adminq_bus_addr);
+	dma_pool_destroy(priv->adminq_pool);
 	gve_clear_admin_queue_ok(priv);
 }
 
@@ -281,7 +311,7 @@
  */
 static int gve_adminq_kick_and_wait(struct gve_priv *priv)
 {
-	u32 tail, head;
+	int tail, head;
 	int i;
 
 	tail = ioread32be(&priv->reg_bar0->adminq_event_counter);
@@ -630,18 +660,7 @@
 			    struct gve_device_descriptor *descriptor)
 {
 	priv->tx_desc_cnt = be16_to_cpu(descriptor->tx_queue_entries);
-	if (priv->tx_desc_cnt * sizeof(priv->tx->desc[0]) < PAGE_SIZE) {
-		dev_err(&priv->pdev->dev, "Tx desc count %d too low\n",
-			priv->tx_desc_cnt);
-		return -EINVAL;
-	}
 	priv->rx_desc_cnt = be16_to_cpu(descriptor->rx_queue_entries);
-	if (priv->rx_desc_cnt * sizeof(priv->rx->desc.desc_ring[0])
-	    < PAGE_SIZE) {
-		dev_err(&priv->pdev->dev, "Rx desc count %d too low\n",
-			priv->rx_desc_cnt);
-		return -EINVAL;
-	}
 	return 0;
 }
 
@@ -673,8 +692,8 @@
 	u16 mtu;
 
 	memset(&cmd, 0, sizeof(cmd));
-	descriptor = dma_alloc_coherent(&priv->pdev->dev, PAGE_SIZE,
-					&descriptor_bus, GFP_KERNEL);
+	descriptor = dma_pool_alloc(priv->adminq_pool, GFP_KERNEL,
+				    &descriptor_bus);
 	if (!descriptor)
 		return -ENOMEM;
 	cmd.opcode = cpu_to_be32(GVE_ADMINQ_DESCRIBE_DEVICE);
@@ -682,7 +701,8 @@
 						cpu_to_be64(descriptor_bus);
 	cmd.describe_device.device_descriptor_version =
 			cpu_to_be32(GVE_ADMINQ_DEVICE_DESCRIPTOR_VERSION);
-	cmd.describe_device.available_length = cpu_to_be32(PAGE_SIZE);
+	cmd.describe_device.available_length =
+		cpu_to_be32(GVE_ADMINQ_BUFFER_SIZE);
 
 	err = gve_adminq_execute_cmd(priv, &cmd);
 	if (err)
@@ -733,7 +753,7 @@
 	}
 	priv->dev->max_mtu = mtu;
 	priv->num_event_counters = be16_to_cpu(descriptor->counters);
-	ether_addr_copy(priv->dev->dev_addr, descriptor->mac);
+	eth_hw_addr_set(priv->dev, descriptor->mac);
 	mac = descriptor->mac;
 	dev_info(&priv->pdev->dev, "MAC addr: %pM\n", mac);
 	priv->tx_pages_per_qpl = be16_to_cpu(descriptor->tx_pages_per_qpl);
@@ -747,8 +767,7 @@
 	priv->default_num_queues = be16_to_cpu(descriptor->default_num_queues);
 
 free_device_descriptor:
-	dma_free_coherent(&priv->pdev->dev, PAGE_SIZE, descriptor,
-			  descriptor_bus);
+	dma_pool_free(priv->adminq_pool, descriptor, descriptor_bus);
 	return err;
 }
 
@@ -777,6 +796,7 @@
 		.page_list_id = cpu_to_be32(qpl->id),
 		.num_pages = cpu_to_be32(num_entries),
 		.page_address_list_addr = cpu_to_be64(page_list_bus),
+		.page_size = cpu_to_be64(PAGE_SIZE),
 	};
 
 	err = gve_adminq_execute_cmd(priv, &cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_adminq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_adminq.h
@@ -149,9 +149,10 @@
 	__be32 page_list_id;
 	__be32 num_pages;
 	__be64 page_address_list_addr;
+	__be64 page_size;
 };
 
-static_assert(sizeof(struct gve_adminq_register_page_list) == 16);
+static_assert(sizeof(struct gve_adminq_register_page_list) == 24);
 
 struct gve_adminq_unregister_page_list {
 	__be32 page_list_id;
@@ -270,6 +271,7 @@
 	TX_LAST_COMPLETION_PROCESSED	= 5,
 	RX_NEXT_EXPECTED_SEQUENCE	= 6,
 	RX_BUFFERS_POSTED		= 7,
+	TX_TIMEOUT_CNT			= 8,
 	// stats from NIC
 	RX_QUEUE_DROP_CNT		= 65,
 	RX_NO_BUFFERS_POSTED		= 66,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_ethtool.c
@@ -174,14 +174,14 @@
 				struct gve_rx_ring *rx = &priv->rx[ring];
 
 				start =
-				  u64_stats_fetch_begin(&priv->rx[ring].statss);
+				  u64_stats_fetch_begin_irq(&priv->rx[ring].statss);
 				tmp_rx_pkts = rx->rpackets;
 				tmp_rx_bytes = rx->rbytes;
 				tmp_rx_skb_alloc_fail = rx->rx_skb_alloc_fail;
 				tmp_rx_buf_alloc_fail = rx->rx_buf_alloc_fail;
 				tmp_rx_desc_err_dropped_pkt =
 					rx->rx_desc_err_dropped_pkt;
-			} while (u64_stats_fetch_retry(&priv->rx[ring].statss,
+			} while (u64_stats_fetch_retry_irq(&priv->rx[ring].statss,
 						       start));
 			rx_pkts += tmp_rx_pkts;
 			rx_bytes += tmp_rx_bytes;
@@ -195,10 +195,10 @@
 		if (priv->tx) {
 			do {
 				start =
-				  u64_stats_fetch_begin(&priv->tx[ring].statss);
+				  u64_stats_fetch_begin_irq(&priv->tx[ring].statss);
 				tmp_tx_pkts = priv->tx[ring].pkt_done;
 				tmp_tx_bytes = priv->tx[ring].bytes_done;
-			} while (u64_stats_fetch_retry(&priv->tx[ring].statss,
+			} while (u64_stats_fetch_retry_irq(&priv->tx[ring].statss,
 						       start));
 			tx_pkts += tmp_tx_pkts;
 			tx_bytes += tmp_tx_bytes;
@@ -256,13 +256,13 @@
 			data[i++] = rx->cnt;
 			do {
 				start =
-				  u64_stats_fetch_begin(&priv->rx[ring].statss);
+				  u64_stats_fetch_begin_irq(&priv->rx[ring].statss);
 				tmp_rx_bytes = rx->rbytes;
 				tmp_rx_skb_alloc_fail = rx->rx_skb_alloc_fail;
 				tmp_rx_buf_alloc_fail = rx->rx_buf_alloc_fail;
 				tmp_rx_desc_err_dropped_pkt =
 					rx->rx_desc_err_dropped_pkt;
-			} while (u64_stats_fetch_retry(&priv->rx[ring].statss,
+			} while (u64_stats_fetch_retry_irq(&priv->rx[ring].statss,
 						       start));
 			data[i++] = tmp_rx_bytes;
 			/* rx dropped packets */
@@ -323,9 +323,9 @@
 			}
 			do {
 				start =
-				  u64_stats_fetch_begin(&priv->tx[ring].statss);
+				  u64_stats_fetch_begin_irq(&priv->tx[ring].statss);
 				tmp_tx_bytes = tx->bytes_done;
-			} while (u64_stats_fetch_retry(&priv->tx[ring].statss,
+			} while (u64_stats_fetch_retry_irq(&priv->tx[ring].statss,
 						       start));
 			data[i++] = tmp_tx_bytes;
 			data[i++] = tx->wake_queue;
@@ -463,7 +463,7 @@
 	case ETHTOOL_RX_COPYBREAK:
 	{
 		u32 max_copybreak = gve_is_gqi(priv) ?
-			(PAGE_SIZE / 2) : priv->data_buffer_size_dqo;
+			GVE_DEFAULT_RX_BUFFER_SIZE : priv->data_buffer_size_dqo;
 
 		len = *(u32 *)value;
 		if (len > max_copybreak)
@@ -526,9 +526,15 @@
 				  struct ethtool_link_ksettings *cmd)
 {
 	struct gve_priv *priv = netdev_priv(netdev);
-	int err = gve_adminq_report_link_speed(priv);
+	int err = 0;
+
+	if (priv->link_speed == 0)
+		err = gve_adminq_report_link_speed(priv);
 
 	cmd->base.speed = priv->link_speed;
+
+	cmd->base.duplex = DUPLEX_FULL;
+
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_main.c
@@ -24,6 +24,9 @@
 #define GVE_VERSION		"1.0.0"
 #define GVE_VERSION_PREFIX	"GVE-"
 
+// Minimum amount of time between queue kicks in msec (10 seconds)
+#define MIN_TX_TIMEOUT_GAP (1000 * 10)
+
 const char gve_version_str[] = GVE_VERSION;
 static const char gve_version_prefix[] = GVE_VERSION_PREFIX;
 
@@ -48,10 +51,10 @@
 		for (ring = 0; ring < priv->rx_cfg.num_queues; ring++) {
 			do {
 				start =
-				  u64_stats_fetch_begin(&priv->rx[ring].statss);
+				  u64_stats_fetch_begin_irq(&priv->rx[ring].statss);
 				packets = priv->rx[ring].rpackets;
 				bytes = priv->rx[ring].rbytes;
-			} while (u64_stats_fetch_retry(&priv->rx[ring].statss,
+			} while (u64_stats_fetch_retry_irq(&priv->rx[ring].statss,
 						       start));
 			s->rx_packets += packets;
 			s->rx_bytes += bytes;
@@ -61,10 +64,10 @@
 		for (ring = 0; ring < priv->tx_cfg.num_queues; ring++) {
 			do {
 				start =
-				  u64_stats_fetch_begin(&priv->tx[ring].statss);
+				  u64_stats_fetch_begin_irq(&priv->tx[ring].statss);
 				packets = priv->tx[ring].pkt_done;
 				bytes = priv->tx[ring].bytes_done;
-			} while (u64_stats_fetch_retry(&priv->tx[ring].statss,
+			} while (u64_stats_fetch_retry_irq(&priv->tx[ring].statss,
 						       start));
 			s->tx_packets += packets;
 			s->tx_bytes += bytes;
@@ -136,7 +139,7 @@
 	rx_stats_num = (GVE_RX_STATS_REPORT_NUM + NIC_RX_STATS_REPORT_NUM) *
 		       priv->rx_cfg.num_queues;
 	priv->stats_report_len = struct_size(priv->stats_report, stats,
-					     tx_stats_num + rx_stats_num);
+					     size_add(tx_stats_num, rx_stats_num));
 	priv->stats_report =
 		dma_alloc_coherent(&priv->pdev->dev, priv->stats_report_len,
 				   &priv->stats_report_bus, GFP_KERNEL);
@@ -198,6 +201,10 @@
 
 	if (block->tx)
 		reschedule |= gve_tx_poll(block, budget);
+
+	if (!budget)
+		return 0;
+
 	if (block->rx)
 		reschedule |= gve_rx_poll(block, budget);
 
@@ -230,22 +237,12 @@
 	bool reschedule = false;
 	int work_done = 0;
 
-	/* Clear PCI MSI-X Pending Bit Array (PBA)
-	 *
-	 * This bit is set if an interrupt event occurs while the vector is
-	 * masked. If this bit is set and we reenable the interrupt, it will
-	 * fire again. Since we're just about to poll the queue state, we don't
-	 * need it to fire again.
-	 *
-	 * Under high softirq load, it's possible that the interrupt condition
-	 * is triggered twice before we got the chance to process it.
-	 */
-	gve_write_irq_doorbell_dqo(priv, block,
-				   GVE_ITR_NO_UPDATE_DQO | GVE_ITR_CLEAR_PBA_BIT_DQO);
-
 	if (block->tx)
 		reschedule |= gve_tx_poll_dqo(block, /*do_clean=*/true);
 
+	if (!budget)
+		return 0;
+
 	if (block->rx) {
 		work_done = gve_rx_poll_dqo(block, budget);
 		reschedule |= work_done == budget;
@@ -743,9 +740,9 @@
 
 int gve_alloc_page(struct gve_priv *priv, struct device *dev,
 		   struct page **page, dma_addr_t *dma,
-		   enum dma_data_direction dir)
+		   enum dma_data_direction dir, gfp_t gfp_flags)
 {
-	*page = alloc_page(GFP_KERNEL);
+	*page = alloc_page(gfp_flags);
 	if (!*page) {
 		priv->page_alloc_fail++;
 		return -ENOMEM;
@@ -789,7 +786,7 @@
 	for (i = 0; i < pages; i++) {
 		err = gve_alloc_page(priv, &priv->pdev->dev, &qpl->pages[i],
 				     &qpl->page_buses[i],
-				     gve_qpl_dma_dir(priv, id));
+				     gve_qpl_dma_dir(priv, id), GFP_KERNEL);
 		/* caller handles clean up */
 		if (err)
 			return -ENOMEM;
@@ -935,7 +932,7 @@
 		/* Hard code this for now. This may be tuned in the future for
 		 * performance.
 		 */
-		priv->data_buffer_size_dqo = GVE_RX_BUFFER_SIZE_DQO;
+		priv->data_buffer_size_dqo = GVE_DEFAULT_RX_BUFFER_SIZE;
 	}
 	err = gve_create_rings(priv);
 	if (err)
@@ -1116,9 +1113,47 @@
 
 static void gve_tx_timeout(struct net_device *dev, unsigned int txqueue)
 {
-	struct gve_priv *priv = netdev_priv(dev);
+	struct gve_notify_block *block;
+	struct gve_tx_ring *tx = NULL;
+	struct gve_priv *priv;
+	u32 last_nic_done;
+	u32 current_time;
+	u32 ntfy_idx;
+
+	netdev_info(dev, "Timeout on tx queue, %d", txqueue);
+	priv = netdev_priv(dev);
+	if (txqueue > priv->tx_cfg.num_queues)
+		goto reset;
 
+	ntfy_idx = gve_tx_idx_to_ntfy(priv, txqueue);
+	if (ntfy_idx >= priv->num_ntfy_blks)
+		goto reset;
+
+	block = &priv->ntfy_blocks[ntfy_idx];
+	tx = block->tx;
+
+	current_time = jiffies_to_msecs(jiffies);
+	if (tx->last_kick_msec + MIN_TX_TIMEOUT_GAP > current_time)
+		goto reset;
+
+	/* Check to see if there are missed completions, which will allow us to
+	 * kick the queue.
+	 */
+	last_nic_done = gve_tx_load_event_counter(priv, tx);
+	if (last_nic_done - tx->done) {
+		netdev_info(dev, "Kicking queue %d", txqueue);
+		iowrite32be(GVE_IRQ_MASK, gve_irq_doorbell(priv, block));
+		napi_schedule(&block->napi);
+		tx->last_kick_msec = current_time;
+		goto out;
+	} // Else reset.
+
+reset:
 	gve_schedule_reset(priv);
+
+out:
+	if (tx)
+		tx->queue_timeout++;
 	priv->tx_timeo_cnt++;
 }
 
@@ -1219,9 +1254,9 @@
 			}
 
 			do {
-				start = u64_stats_fetch_begin(&priv->tx[idx].statss);
+				start = u64_stats_fetch_begin_irq(&priv->tx[idx].statss);
 				tx_bytes = priv->tx[idx].bytes_done;
-			} while (u64_stats_fetch_retry(&priv->tx[idx].statss, start));
+			} while (u64_stats_fetch_retry_irq(&priv->tx[idx].statss, start));
 			stats[stats_idx++] = (struct stats) {
 				.stat_name = cpu_to_be32(TX_WAKE_CNT),
 				.value = cpu_to_be64(priv->tx[idx].wake_queue),
@@ -1247,6 +1282,11 @@
 				.value = cpu_to_be64(last_completion),
 				.queue_id = cpu_to_be32(idx),
 			};
+			stats[stats_idx++] = (struct stats) {
+				.stat_name = cpu_to_be32(TX_TIMEOUT_CNT),
+				.value = cpu_to_be64(priv->tx[idx].queue_timeout),
+				.queue_id = cpu_to_be32(idx),
+			};
 		}
 	}
 	/* rx stats */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_register.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_register.h
@@ -18,11 +18,20 @@
 	__be32	adminq_event_counter;
 	u8	reserved[3];
 	u8	driver_version;
+	__be32	adminq_base_address_hi;
+	__be32	adminq_base_address_lo;
+	__be16	adminq_length;
 };
 
 enum gve_device_status_flags {
 	GVE_DEVICE_STATUS_RESET_MASK		= BIT(1),
 	GVE_DEVICE_STATUS_LINK_STATUS_MASK	= BIT(2),
 	GVE_DEVICE_STATUS_REPORT_STATS_MASK	= BIT(3),
+	GVE_DEVICE_STATUS_DEVICE_IS_RESET	= BIT(4),
+};
+
+enum gve_driver_status_flags {
+	GVE_DRIVER_STATUS_RUN_MASK		= BIT(0),
+	GVE_DRIVER_STATUS_RESET_MASK		= BIT(1),
 };
 #endif /* _GVE_REGISTER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_rx.c
@@ -79,7 +79,8 @@
 	dma_addr_t dma;
 	int err;
 
-	err = gve_alloc_page(priv, dev, &page, &dma, DMA_FROM_DEVICE);
+	err = gve_alloc_page(priv, dev, &page, &dma, DMA_FROM_DEVICE,
+			     GFP_ATOMIC);
 	if (err)
 		return err;
 
@@ -140,9 +141,9 @@
 {
 	struct gve_rx_ring *rx = &priv->rx[idx];
 	struct device *hdev = &priv->pdev->dev;
-	u32 slots, npages;
 	int filled_pages;
 	size_t bytes;
+	u32 slots;
 	int err;
 
 	netif_dbg(priv, drv, priv->dev, "allocating rx ring\n");
@@ -187,12 +188,6 @@
 
 	/* alloc rx desc ring */
 	bytes = sizeof(struct gve_rx_desc) * priv->rx_desc_cnt;
-	npages = bytes / PAGE_SIZE;
-	if (npages * PAGE_SIZE != bytes) {
-		err = -EIO;
-		goto abort_with_q_resources;
-	}
-
 	rx->desc.desc_ring = dma_alloc_coherent(hdev, bytes, &rx->desc.bus,
 						GFP_KERNEL);
 	if (!rx->desc.desc_ring) {
@@ -286,10 +281,10 @@
 
 static void gve_rx_flip_buff(struct gve_rx_slot_page_info *page_info, __be64 *slot_addr)
 {
-	const __be64 offset = cpu_to_be64(PAGE_SIZE / 2);
+	const __be64 offset = cpu_to_be64(GVE_DEFAULT_RX_BUFFER_OFFSET);
 
 	/* "flip" to other packet buffer on this page */
-	page_info->page_offset ^= PAGE_SIZE / 2;
+	page_info->page_offset ^= GVE_DEFAULT_RX_BUFFER_OFFSET;
 	*(slot_addr) ^= offset;
 }
 
@@ -449,6 +444,7 @@
 		skb_set_hash(skb, be32_to_cpu(rx_desc->rss_hash),
 			     gve_rss_type(rx_desc->flags_seq));
 
+	skb_record_rx_queue(skb, rx->q_num);
 	if (skb_is_nonlinear(skb))
 		napi_gro_frags(napi);
 	else
@@ -514,8 +510,13 @@
 
 				gve_rx_free_buffer(dev, page_info, data_slot);
 				page_info->page = NULL;
-				if (gve_rx_alloc_buffer(priv, dev, page_info, data_slot))
+				if (gve_rx_alloc_buffer(priv, dev, page_info,
+							data_slot)) {
+					u64_stats_update_begin(&rx->statss);
+					rx->rx_buf_alloc_fail++;
+					u64_stats_update_end(&rx->statss);
 					break;
+				}
 			}
 		}
 		fill_cnt++;
@@ -599,10 +600,6 @@
 
 	feat = block->napi.dev->features;
 
-	/* If budget is 0, do all the work */
-	if (budget == 0)
-		budget = INT_MAX;
-
 	if (budget > 0)
 		repoll |= gve_clean_rx_done(rx, budget, feat);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_rx_dqo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_rx_dqo.c
@@ -157,7 +157,7 @@
 	int err;
 
 	err = gve_alloc_page(priv, &priv->pdev->dev, &buf_state->page_info.page,
-			     &buf_state->addr, DMA_FROM_DEVICE);
+			     &buf_state->addr, DMA_FROM_DEVICE, GFP_ATOMIC);
 	if (err)
 		return err;
 
@@ -240,8 +240,8 @@
 	rx->dqo.bufq.mask = buffer_queue_slots - 1;
 	rx->dqo.complq.num_free_slots = completion_queue_slots;
 	rx->dqo.complq.mask = completion_queue_slots - 1;
-	rx->skb_head = NULL;
-	rx->skb_tail = NULL;
+	rx->ctx.skb_head = NULL;
+	rx->ctx.skb_tail = NULL;
 
 	rx->dqo.num_buf_states = min_t(s16, S16_MAX, buffer_queue_slots * 4);
 	rx->dqo.buf_states = kvcalloc(rx->dqo.num_buf_states,
@@ -465,14 +465,16 @@
 	skb_set_hash(skb, le32_to_cpu(compl_desc->hash), hash_type);
 }
 
-static void gve_rx_free_skb(struct gve_rx_ring *rx)
+static void gve_rx_free_skb(struct napi_struct *napi, struct gve_rx_ring *rx)
 {
-	if (!rx->skb_head)
+	if (!rx->ctx.skb_head)
 		return;
 
-	dev_kfree_skb_any(rx->skb_head);
-	rx->skb_head = NULL;
-	rx->skb_tail = NULL;
+	if (rx->ctx.skb_head == napi->skb)
+		napi->skb = NULL;
+	dev_kfree_skb_any(rx->ctx.skb_head);
+	rx->ctx.skb_head = NULL;
+	rx->ctx.skb_tail = NULL;
 }
 
 /* Chains multi skbs for single rx packet.
@@ -483,7 +485,7 @@
 			       u16 buf_len, struct gve_rx_ring *rx,
 			       struct gve_priv *priv)
 {
-	int num_frags = skb_shinfo(rx->skb_tail)->nr_frags;
+	int num_frags = skb_shinfo(rx->ctx.skb_tail)->nr_frags;
 
 	if (unlikely(num_frags == MAX_SKB_FRAGS)) {
 		struct sk_buff *skb;
@@ -492,17 +494,17 @@
 		if (!skb)
 			return -1;
 
-		skb_shinfo(rx->skb_tail)->frag_list = skb;
-		rx->skb_tail = skb;
+		skb_shinfo(rx->ctx.skb_tail)->frag_list = skb;
+		rx->ctx.skb_tail = skb;
 		num_frags = 0;
 	}
-	if (rx->skb_tail != rx->skb_head) {
-		rx->skb_head->len += buf_len;
-		rx->skb_head->data_len += buf_len;
-		rx->skb_head->truesize += priv->data_buffer_size_dqo;
+	if (rx->ctx.skb_tail != rx->ctx.skb_head) {
+		rx->ctx.skb_head->len += buf_len;
+		rx->ctx.skb_head->data_len += buf_len;
+		rx->ctx.skb_head->truesize += priv->data_buffer_size_dqo;
 	}
 
-	skb_add_rx_frag(rx->skb_tail, num_frags,
+	skb_add_rx_frag(rx->ctx.skb_tail, num_frags,
 			buf_state->page_info.page,
 			buf_state->page_info.page_offset,
 			buf_len, priv->data_buffer_size_dqo);
@@ -556,7 +558,7 @@
 				      buf_len, DMA_FROM_DEVICE);
 
 	/* Append to current skb if one exists. */
-	if (rx->skb_head) {
+	if (rx->ctx.skb_head) {
 		if (unlikely(gve_rx_append_frags(napi, buf_state, buf_len, rx,
 						 priv)) != 0) {
 			goto error;
@@ -567,11 +569,11 @@
 	}
 
 	if (eop && buf_len <= priv->rx_copybreak) {
-		rx->skb_head = gve_rx_copy(priv->dev, napi,
-					   &buf_state->page_info, buf_len, 0);
-		if (unlikely(!rx->skb_head))
+		rx->ctx.skb_head = gve_rx_copy(priv->dev, napi,
+					       &buf_state->page_info, buf_len, 0);
+		if (unlikely(!rx->ctx.skb_head))
 			goto error;
-		rx->skb_tail = rx->skb_head;
+		rx->ctx.skb_tail = rx->ctx.skb_head;
 
 		u64_stats_update_begin(&rx->statss);
 		rx->rx_copied_pkt++;
@@ -583,12 +585,12 @@
 		return 0;
 	}
 
-	rx->skb_head = napi_get_frags(napi);
-	if (unlikely(!rx->skb_head))
+	rx->ctx.skb_head = napi_get_frags(napi);
+	if (unlikely(!rx->ctx.skb_head))
 		goto error;
-	rx->skb_tail = rx->skb_head;
+	rx->ctx.skb_tail = rx->ctx.skb_head;
 
-	skb_add_rx_frag(rx->skb_head, 0, buf_state->page_info.page,
+	skb_add_rx_frag(rx->ctx.skb_head, 0, buf_state->page_info.page,
 			buf_state->page_info.page_offset, buf_len,
 			priv->data_buffer_size_dqo);
 	gve_dec_pagecnt_bias(&buf_state->page_info);
@@ -635,27 +637,27 @@
 		rx->gve->ptype_lut_dqo->ptypes[desc->packet_type];
 	int err;
 
-	skb_record_rx_queue(rx->skb_head, rx->q_num);
+	skb_record_rx_queue(rx->ctx.skb_head, rx->q_num);
 
 	if (feat & NETIF_F_RXHASH)
-		gve_rx_skb_hash(rx->skb_head, desc, ptype);
+		gve_rx_skb_hash(rx->ctx.skb_head, desc, ptype);
 
 	if (feat & NETIF_F_RXCSUM)
-		gve_rx_skb_csum(rx->skb_head, desc, ptype);
+		gve_rx_skb_csum(rx->ctx.skb_head, desc, ptype);
 
 	/* RSC packets must set gso_size otherwise the TCP stack will complain
 	 * that packets are larger than MTU.
 	 */
 	if (desc->rsc) {
-		err = gve_rx_complete_rsc(rx->skb_head, desc, ptype);
+		err = gve_rx_complete_rsc(rx->ctx.skb_head, desc, ptype);
 		if (err < 0)
 			return err;
 	}
 
-	if (skb_headlen(rx->skb_head) == 0)
+	if (skb_headlen(rx->ctx.skb_head) == 0)
 		napi_gro_frags(napi);
 	else
-		napi_gro_receive(napi, rx->skb_head);
+		napi_gro_receive(napi, rx->ctx.skb_head);
 
 	return 0;
 }
@@ -690,7 +692,7 @@
 
 		err = gve_rx_dqo(napi, rx, compl_desc, rx->q_num);
 		if (err < 0) {
-			gve_rx_free_skb(rx);
+			gve_rx_free_skb(napi, rx);
 			u64_stats_update_begin(&rx->statss);
 			if (err == -ENOMEM)
 				rx->rx_skb_alloc_fail++;
@@ -717,23 +719,23 @@
 		/* Free running counter of completed descriptors */
 		rx->cnt++;
 
-		if (!rx->skb_head)
+		if (!rx->ctx.skb_head)
 			continue;
 
 		if (!compl_desc->end_of_packet)
 			continue;
 
 		work_done++;
-		pkt_bytes = rx->skb_head->len;
+		pkt_bytes = rx->ctx.skb_head->len;
 		/* The ethernet header (first ETH_HLEN bytes) is snipped off
 		 * by eth_type_trans.
 		 */
-		if (skb_headlen(rx->skb_head))
+		if (skb_headlen(rx->ctx.skb_head))
 			pkt_bytes += ETH_HLEN;
 
 		/* gve_rx_complete_skb() will consume skb if successful */
 		if (gve_rx_complete_skb(rx, napi, compl_desc, feat) != 0) {
-			gve_rx_free_skb(rx);
+			gve_rx_free_skb(napi, rx);
 			u64_stats_update_begin(&rx->statss);
 			rx->rx_desc_err_dropped_pkt++;
 			u64_stats_update_end(&rx->statss);
@@ -741,8 +743,8 @@
 		}
 
 		bytes += pkt_bytes;
-		rx->skb_head = NULL;
-		rx->skb_tail = NULL;
+		rx->ctx.skb_head = NULL;
+		rx->ctx.skb_tail = NULL;
 	}
 
 	gve_rx_post_buffers_dqo(rx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_tx.c
@@ -283,8 +283,8 @@
 	int bytes;
 	int hlen;
 
-	hlen = skb_is_gso(skb) ? skb_checksum_start_offset(skb) +
-				 tcp_hdrlen(skb) : skb_headlen(skb);
+	hlen = skb_is_gso(skb) ? skb_checksum_start_offset(skb) + tcp_hdrlen(skb) :
+				 min_t(int, GVE_GQ_TX_MIN_PKT_DESC_BYTES, skb->len);
 
 	pad_bytes = gve_tx_fifo_pad_alloc_one_frag(&tx->tx_fifo,
 						   hlen);
@@ -303,15 +303,15 @@
 static void gve_tx_unmap_buf(struct device *dev, struct gve_tx_buffer_state *info)
 {
 	if (info->skb) {
-		dma_unmap_single(dev, dma_unmap_addr(&info->buf, dma),
-				 dma_unmap_len(&info->buf, len),
+		dma_unmap_single(dev, dma_unmap_addr(info, dma),
+				 dma_unmap_len(info, len),
 				 DMA_TO_DEVICE);
-		dma_unmap_len_set(&info->buf, len, 0);
+		dma_unmap_len_set(info, len, 0);
 	} else {
-		dma_unmap_page(dev, dma_unmap_addr(&info->buf, dma),
-			       dma_unmap_len(&info->buf, len),
+		dma_unmap_page(dev, dma_unmap_addr(info, dma),
+			       dma_unmap_len(info, len),
 			       DMA_TO_DEVICE);
-		dma_unmap_len_set(&info->buf, len, 0);
+		dma_unmap_len_set(info, len, 0);
 	}
 }
 
@@ -431,13 +431,11 @@
 	pkt_desc = &tx->desc[idx];
 
 	l4_hdr_offset = skb_checksum_start_offset(skb);
-	/* If the skb is gso, then we want the tcp header in the first segment
-	 * otherwise we want the linear portion of the skb (which will contain
-	 * the checksum because skb->csum_start and skb->csum_offset are given
-	 * relative to skb->head) in the first segment.
+	/* If the skb is gso, then we want the tcp header alone in the first segment
+	 * otherwise we want the minimum required by the gVNIC spec.
 	 */
 	hlen = is_gso ? l4_hdr_offset + tcp_hdrlen(skb) :
-			skb_headlen(skb);
+			min_t(int, GVE_GQ_TX_MIN_PKT_DESC_BYTES, skb->len);
 
 	info->skb =  skb;
 	/* We don't want to split the header, so if necessary, pad to the end
@@ -491,7 +489,6 @@
 	struct gve_tx_buffer_state *info;
 	bool is_gso = skb_is_gso(skb);
 	u32 idx = tx->req & tx->mask;
-	struct gve_tx_dma_buf *buf;
 	u64 addr;
 	u32 len;
 	int i;
@@ -515,9 +512,8 @@
 		tx->dma_mapping_error++;
 		goto drop;
 	}
-	buf = &info->buf;
-	dma_unmap_len_set(buf, len, len);
-	dma_unmap_addr_set(buf, dma, addr);
+	dma_unmap_len_set(info, len, len);
+	dma_unmap_addr_set(info, dma, addr);
 
 	payload_nfrags = shinfo->nr_frags;
 	if (hlen < len) {
@@ -549,10 +545,9 @@
 			tx->dma_mapping_error++;
 			goto unmap_drop;
 		}
-		buf = &tx->info[idx].buf;
 		tx->info[idx].skb = NULL;
-		dma_unmap_len_set(buf, len, len);
-		dma_unmap_addr_set(buf, dma, addr);
+		dma_unmap_len_set(&tx->info[idx], len, len);
+		dma_unmap_addr_set(&tx->info[idx], dma, addr);
 
 		gve_tx_fill_seg_desc(seg_desc, skb, is_gso, len, addr);
 	}
@@ -612,7 +607,7 @@
 	return NETDEV_TX_OK;
 }
 
-#define GVE_TX_START_THRESH	PAGE_SIZE
+#define GVE_TX_START_THRESH	4096
 
 static int gve_clean_tx_done(struct gve_priv *priv, struct gve_tx_ring *tx,
 			     u32 to_do, bool try_to_wake)
@@ -691,10 +686,6 @@
 	u32 nic_done;
 	u32 to_do;
 
-	/* If budget is 0, do all the work */
-	if (budget == 0)
-		budget = INT_MAX;
-
 	/* Find out how much work there is to be done */
 	tx->last_nic_done = gve_tx_load_event_counter(priv, tx);
 	nic_done = be32_to_cpu(tx->last_nic_done);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/google/gve/gve_tx_dqo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/google/gve/gve_tx_dqo.c
@@ -85,18 +85,16 @@
 		int j;
 
 		for (j = 0; j < cur_state->num_bufs; j++) {
-			struct gve_tx_dma_buf *buf = &cur_state->bufs[j];
-
 			if (j == 0) {
 				dma_unmap_single(tx->dev,
-						 dma_unmap_addr(buf, dma),
-						 dma_unmap_len(buf, len),
-						 DMA_TO_DEVICE);
+					dma_unmap_addr(cur_state, dma[j]),
+					dma_unmap_len(cur_state, len[j]),
+					DMA_TO_DEVICE);
 			} else {
 				dma_unmap_page(tx->dev,
-					       dma_unmap_addr(buf, dma),
-					       dma_unmap_len(buf, len),
-					       DMA_TO_DEVICE);
+					dma_unmap_addr(cur_state, dma[j]),
+					dma_unmap_len(cur_state, len[j]),
+					DMA_TO_DEVICE);
 			}
 		}
 		if (cur_state->skb) {
@@ -352,6 +350,7 @@
 /* Validates and prepares `skb` for TSO.
  *
  * Returns header length, or < 0 if invalid.
+ * Warning : Might change skb->head (and thus skb_shinfo).
  */
 static int gve_prep_tso(struct sk_buff *skb)
 {
@@ -453,19 +452,19 @@
 static int gve_tx_add_skb_no_copy_dqo(struct gve_tx_ring *tx,
 				      struct sk_buff *skb)
 {
-	const struct skb_shared_info *shinfo = skb_shinfo(skb);
 	const bool is_gso = skb_is_gso(skb);
+	struct skb_shared_info *shinfo;
 	u32 desc_idx = tx->dqo_tx.tail;
 
-	struct gve_tx_pending_packet_dqo *pending_packet;
+	struct gve_tx_pending_packet_dqo *pkt;
 	struct gve_tx_metadata_dqo metadata;
 	s16 completion_tag;
 	int i;
 
-	pending_packet = gve_alloc_pending_packet(tx);
-	pending_packet->skb = skb;
-	pending_packet->num_bufs = 0;
-	completion_tag = pending_packet - tx->dqo.pending_packets;
+	pkt = gve_alloc_pending_packet(tx);
+	pkt->skb = skb;
+	pkt->num_bufs = 0;
+	completion_tag = pkt - tx->dqo.pending_packets;
 
 	gve_extract_tx_metadata_dqo(skb, &metadata);
 	if (is_gso) {
@@ -479,6 +478,8 @@
 		desc_idx = (desc_idx + 1) & tx->mask;
 	}
 
+	/* Must get after gve_prep_tso(), which can change shinfo. */
+	shinfo = skb_shinfo(skb);
 	gve_tx_fill_general_ctx_desc(&tx->dqo.tx_ring[desc_idx].general_ctx,
 				     &metadata);
 	desc_idx = (desc_idx + 1) & tx->mask;
@@ -493,8 +494,6 @@
 
 	/* Map the linear portion of skb */
 	{
-		struct gve_tx_dma_buf *buf =
-			&pending_packet->bufs[pending_packet->num_bufs];
 		u32 len = skb_headlen(skb);
 		dma_addr_t addr;
 
@@ -502,9 +501,9 @@
 		if (unlikely(dma_mapping_error(tx->dev, addr)))
 			goto err;
 
-		dma_unmap_len_set(buf, len, len);
-		dma_unmap_addr_set(buf, dma, addr);
-		++pending_packet->num_bufs;
+		dma_unmap_len_set(pkt, len[pkt->num_bufs], len);
+		dma_unmap_addr_set(pkt, dma[pkt->num_bufs], addr);
+		++pkt->num_bufs;
 
 		gve_tx_fill_pkt_desc_dqo(tx, &desc_idx, skb, len, addr,
 					 completion_tag,
@@ -512,8 +511,6 @@
 	}
 
 	for (i = 0; i < shinfo->nr_frags; i++) {
-		struct gve_tx_dma_buf *buf =
-			&pending_packet->bufs[pending_packet->num_bufs];
 		const skb_frag_t *frag = &shinfo->frags[i];
 		bool is_eop = i == (shinfo->nr_frags - 1);
 		u32 len = skb_frag_size(frag);
@@ -523,9 +520,9 @@
 		if (unlikely(dma_mapping_error(tx->dev, addr)))
 			goto err;
 
-		dma_unmap_len_set(buf, len, len);
-		dma_unmap_addr_set(buf, dma, addr);
-		++pending_packet->num_bufs;
+		dma_unmap_len_set(pkt, len[pkt->num_bufs], len);
+		dma_unmap_addr_set(pkt, dma[pkt->num_bufs], addr);
+		++pkt->num_bufs;
 
 		gve_tx_fill_pkt_desc_dqo(tx, &desc_idx, skb, len, addr,
 					 completion_tag, is_eop, is_gso);
@@ -552,22 +549,23 @@
 	return 0;
 
 err:
-	for (i = 0; i < pending_packet->num_bufs; i++) {
-		struct gve_tx_dma_buf *buf = &pending_packet->bufs[i];
-
+	for (i = 0; i < pkt->num_bufs; i++) {
 		if (i == 0) {
-			dma_unmap_single(tx->dev, dma_unmap_addr(buf, dma),
-					 dma_unmap_len(buf, len),
+			dma_unmap_single(tx->dev,
+					 dma_unmap_addr(pkt, dma[i]),
+					 dma_unmap_len(pkt, len[i]),
 					 DMA_TO_DEVICE);
 		} else {
-			dma_unmap_page(tx->dev, dma_unmap_addr(buf, dma),
-				       dma_unmap_len(buf, len), DMA_TO_DEVICE);
+			dma_unmap_page(tx->dev,
+				       dma_unmap_addr(pkt, dma[i]),
+				       dma_unmap_len(pkt, len[i]),
+				       DMA_TO_DEVICE);
 		}
 	}
 
-	pending_packet->skb = NULL;
-	pending_packet->num_bufs = 0;
-	gve_free_pending_packet(tx, pending_packet);
+	pkt->skb = NULL;
+	pkt->num_bufs = 0;
+	gve_free_pending_packet(tx, pkt);
 
 	return -1;
 }
@@ -608,22 +606,42 @@
 	const struct skb_shared_info *shinfo = skb_shinfo(skb);
 	const int gso_size = shinfo->gso_size;
 	int cur_seg_num_bufs;
+	int prev_frag_size;
 	int cur_seg_size;
 	int i;
 
 	cur_seg_size = skb_headlen(skb) - header_len;
+	prev_frag_size = skb_headlen(skb);
 	cur_seg_num_bufs = cur_seg_size > 0;
 
 	for (i = 0; i < shinfo->nr_frags; i++) {
 		if (cur_seg_size >= gso_size) {
 			cur_seg_size %= gso_size;
 			cur_seg_num_bufs = cur_seg_size > 0;
+
+			if (prev_frag_size > GVE_TX_MAX_BUF_SIZE_DQO) {
+				int prev_frag_remain = prev_frag_size %
+					GVE_TX_MAX_BUF_SIZE_DQO;
+
+				/* If the last descriptor of the previous frag
+				 * is less than cur_seg_size, the segment will
+				 * span two descriptors in the previous frag.
+				 * Since max gso size (9728) is less than
+				 * GVE_TX_MAX_BUF_SIZE_DQO, it is impossible
+				 * for the segment to span more than two
+				 * descriptors.
+				 */
+				if (prev_frag_remain &&
+				    cur_seg_size > prev_frag_remain)
+					cur_seg_num_bufs++;
+			}
 		}
 
 		if (unlikely(++cur_seg_num_bufs > max_bufs_per_seg))
 			return false;
 
-		cur_seg_size += skb_frag_size(&shinfo->frags[i]);
+		prev_frag_size = skb_frag_size(&shinfo->frags[i]);
+		cur_seg_size += prev_frag_size;
 	}
 
 	return true;
@@ -725,12 +743,12 @@
 
 static void remove_from_list(struct gve_tx_ring *tx,
 			     struct gve_index_list *list,
-			     struct gve_tx_pending_packet_dqo *pending_packet)
+			     struct gve_tx_pending_packet_dqo *pkt)
 {
 	s16 prev_index, next_index;
 
-	prev_index = pending_packet->prev;
-	next_index = pending_packet->next;
+	prev_index = pkt->prev;
+	next_index = pkt->next;
 
 	if (prev_index == -1) {
 		/* Node is head */
@@ -747,21 +765,18 @@
 }
 
 static void gve_unmap_packet(struct device *dev,
-			     struct gve_tx_pending_packet_dqo *pending_packet)
+			     struct gve_tx_pending_packet_dqo *pkt)
 {
-	struct gve_tx_dma_buf *buf;
 	int i;
 
 	/* SKB linear portion is guaranteed to be mapped */
-	buf = &pending_packet->bufs[0];
-	dma_unmap_single(dev, dma_unmap_addr(buf, dma),
-			 dma_unmap_len(buf, len), DMA_TO_DEVICE);
-	for (i = 1; i < pending_packet->num_bufs; i++) {
-		buf = &pending_packet->bufs[i];
-		dma_unmap_page(dev, dma_unmap_addr(buf, dma),
-			       dma_unmap_len(buf, len), DMA_TO_DEVICE);
+	dma_unmap_single(dev, dma_unmap_addr(pkt, dma[0]),
+			 dma_unmap_len(pkt, len[0]), DMA_TO_DEVICE);
+	for (i = 1; i < pkt->num_bufs; i++) {
+		dma_unmap_page(dev, dma_unmap_addr(pkt, dma[i]),
+			       dma_unmap_len(pkt, len[i]), DMA_TO_DEVICE);
 	}
-	pending_packet->num_bufs = 0;
+	pkt->num_bufs = 0;
 }
 
 /* Completion types and expected behavior:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hip04_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hip04_eth.c
@@ -947,6 +947,7 @@
 	priv->tx_coalesce_timer.function = tx_done;
 
 	priv->map = syscon_node_to_regmap(arg.np);
+	of_node_put(arg.np);
 	if (IS_ERR(priv->map)) {
 		dev_warn(d, "no syscon hisilicon,hip04-ppe\n");
 		ret = PTR_ERR(priv->map);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hisi_femac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hisi_femac.c
@@ -283,7 +283,7 @@
 		skb->protocol = eth_type_trans(skb, dev);
 		napi_gro_receive(&priv->napi, skb);
 		dev->stats.rx_packets++;
-		dev->stats.rx_bytes += skb->len;
+		dev->stats.rx_bytes += len;
 next:
 		pos = (pos + 1) % rxq->num;
 		if (rx_pkts_num >= limit)
@@ -427,7 +427,7 @@
 }
 
 static int hisi_femac_set_hw_mac_addr(struct hisi_femac_priv *priv,
-				      unsigned char *mac)
+				      const unsigned char *mac)
 {
 	u32 reg;
 
@@ -841,7 +841,7 @@
 			   (unsigned long)phy->phy_id,
 			   phy_modes(phy->interface));
 
-	ret = of_get_mac_address(node, ndev->dev_addr);
+	ret = of_get_ethdev_address(node, ndev);
 	if (ret) {
 		eth_hw_addr_random(ndev);
 		dev_warn(dev, "using random MAC address %pM\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hix5hd2_gmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hix5hd2_gmac.c
@@ -429,7 +429,7 @@
 static void hix5hd2_hw_set_mac_addr(struct net_device *dev)
 {
 	struct hix5hd2_priv *priv = netdev_priv(dev);
-	unsigned char *mac = dev->dev_addr;
+	const unsigned char *mac = dev->dev_addr;
 	u32 val;
 
 	val = mac[1] | (mac[0] << 8);
@@ -550,7 +550,7 @@
 		skb->protocol = eth_type_trans(skb, dev);
 		napi_gro_receive(&priv->napi, skb);
 		dev->stats.rx_packets++;
-		dev->stats.rx_bytes += skb->len;
+		dev->stats.rx_bytes += len;
 next:
 		pos = dma_ring_incr(pos, RX_DESC_NUM);
 	}
@@ -1219,7 +1219,7 @@
 		goto out_phy_node;
 	}
 
-	ret = of_get_mac_address(node, ndev->dev_addr);
+	ret = of_get_ethdev_address(node, ndev);
 	if (ret) {
 		eth_hw_addr_random(ndev);
 		netdev_warn(ndev, "using random MAC address %pM\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hnae.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hnae.c
@@ -419,8 +419,10 @@
 	hdev->cls_dev.release = hnae_release;
 	(void)dev_set_name(&hdev->cls_dev, "hnae%d", hdev->id);
 	ret = device_register(&hdev->cls_dev);
-	if (ret)
+	if (ret) {
+		put_device(&hdev->cls_dev);
 		return ret;
+	}
 
 	__module_get(THIS_MODULE);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hnae.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hnae.h
@@ -499,7 +499,7 @@
 				   u32 *tx_usecs_high, u32 *rx_usecs_high);
 	void (*set_promisc_mode)(struct hnae_handle *handle, u32 en);
 	int (*get_mac_addr)(struct hnae_handle *handle, void **p);
-	int (*set_mac_addr)(struct hnae_handle *handle, void *p);
+	int (*set_mac_addr)(struct hnae_handle *handle, const void *p);
 	int (*add_uc_addr)(struct hnae_handle *handle,
 			   const unsigned char *addr);
 	int (*rm_uc_addr)(struct hnae_handle *handle,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c
@@ -207,7 +207,7 @@
 		hns_rcb_reset_ring_hw(q);
 }
 
-static int hns_ae_set_mac_address(struct hnae_handle *handle, void *p)
+static int hns_ae_set_mac_address(struct hnae_handle *handle, const void *p)
 {
 	int ret;
 	struct hns_mac_cb *mac_cb = hns_get_mac_cb(handle);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c
@@ -450,7 +450,7 @@
 		+= dsaf_read_dev(drv, GMAC_TX_PAUSE_FRAMES_REG);
 }
 
-static void hns_gmac_set_mac_addr(void *mac_drv, char *mac_addr)
+static void hns_gmac_set_mac_addr(void *mac_drv, const char *mac_addr)
 {
 	struct mac_driver *drv = (struct mac_driver *)mac_drv;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c
@@ -66,6 +66,27 @@
 	}
 }
 
+static u32 hns_mac_link_anti_shake(struct mac_driver *mac_ctrl_drv)
+{
+#define HNS_MAC_LINK_WAIT_TIME 5
+#define HNS_MAC_LINK_WAIT_CNT 40
+
+	u32 link_status = 0;
+	int i;
+
+	if (!mac_ctrl_drv->get_link_status)
+		return link_status;
+
+	for (i = 0; i < HNS_MAC_LINK_WAIT_CNT; i++) {
+		msleep(HNS_MAC_LINK_WAIT_TIME);
+		mac_ctrl_drv->get_link_status(mac_ctrl_drv, &link_status);
+		if (!link_status)
+			break;
+	}
+
+	return link_status;
+}
+
 void hns_mac_get_link_status(struct hns_mac_cb *mac_cb, u32 *link_status)
 {
 	struct mac_driver *mac_ctrl_drv;
@@ -83,6 +104,14 @@
 							       &sfp_prsnt);
 		if (!ret)
 			*link_status = *link_status && sfp_prsnt;
+
+		/* for FIBER port, it may have a fake link up.
+		 * when the link status changes from down to up, we need to do
+		 * anti-shake. the anti-shake time is base on tests.
+		 * only FIBER port need to do this.
+		 */
+		if (*link_status && !mac_cb->link)
+			*link_status = hns_mac_link_anti_shake(mac_ctrl_drv);
 	}
 
 	mac_cb->link = *link_status;
@@ -240,7 +269,7 @@
  *@addr:mac address
  */
 int hns_mac_change_vf_addr(struct hns_mac_cb *mac_cb,
-			   u32 vmid, char *addr)
+			   u32 vmid, const char *addr)
 {
 	int ret;
 	struct mac_driver *mac_ctrl_drv = hns_mac_get_drv(mac_cb);
@@ -904,6 +933,7 @@
 			mac_cb->cpld_ctrl = NULL;
 		} else {
 			syscon = syscon_node_to_regmap(cpld_args.np);
+			of_node_put(cpld_args.np);
 			if (IS_ERR_OR_NULL(syscon)) {
 				dev_dbg(mac_cb->dev, "no cpld-syscon found!\n");
 				mac_cb->cpld_ctrl = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.h
@@ -348,7 +348,7 @@
 	/*disable mac when disable nic or dsaf*/
 	void (*mac_disable)(void *mac_drv, enum mac_commom_mode mode);
 	/* config mac address*/
-	void (*set_mac_addr)(void *mac_drv,	char *mac_addr);
+	void (*set_mac_addr)(void *mac_drv,	const char *mac_addr);
 	/*adjust mac mode of port,include speed and duplex*/
 	int (*adjust_link)(void *mac_drv, enum mac_speed speed,
 			   u32 full_duplex);
@@ -425,7 +425,8 @@
 void mac_adjust_link(struct net_device *net_dev);
 bool hns_mac_need_adjust_link(struct hns_mac_cb *mac_cb, int speed, int duplex);
 void hns_mac_get_link_status(struct hns_mac_cb *mac_cb,	u32 *link_status);
-int hns_mac_change_vf_addr(struct hns_mac_cb *mac_cb, u32 vmid, char *addr);
+int hns_mac_change_vf_addr(struct hns_mac_cb *mac_cb, u32 vmid,
+			   const char *addr);
 int hns_mac_set_multi(struct hns_mac_cb *mac_cb,
 		      u32 port_num, char *addr, bool enable);
 int hns_mac_vm_config_bc_en(struct hns_mac_cb *mac_cb, u32 vm, bool enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c
@@ -400,6 +400,10 @@
 		return;
 
 	if (!HNS_DSAF_IS_DEBUG(dsaf_dev)) {
+		/* DSAF_MAX_PORT_NUM is 6, but DSAF_GE_NUM is 8.
+		   We need check to prevent array overflow */
+		if (port >= DSAF_MAX_PORT_NUM)
+			return;
 		reg_val_1  = 0x1 << port;
 		port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
 		/* there is difference between V1 and V2 in register.*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c
@@ -255,7 +255,7 @@
 	dsaf_write_dev(drv, XGMAC_MAC_PAUSE_CTRL_REG, origin);
 }
 
-static void hns_xgmac_set_pausefrm_mac_addr(void *mac_drv, char *mac_addr)
+static void hns_xgmac_set_pausefrm_mac_addr(void *mac_drv, const char *mac_addr)
 {
 	struct mac_driver *drv = (struct mac_driver *)mac_drv;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/Makefile
@@ -4,9 +4,9 @@
 #
 
 ccflags-y += -I$(srctree)/$(src)
-
-obj-$(CONFIG_HNS3) += hns3pf/
-obj-$(CONFIG_HNS3) += hns3vf/
+ccflags-y += -I$(srctree)/drivers/net/ethernet/hisilicon/hns3/hns3pf
+ccflags-y += -I$(srctree)/drivers/net/ethernet/hisilicon/hns3/hns3vf
+ccflags-y += -I$(srctree)/drivers/net/ethernet/hisilicon/hns3/hns3_common
 
 obj-$(CONFIG_HNS3) += hnae3.o
 
@@ -14,3 +14,15 @@
 hns3-objs = hns3_enet.o hns3_ethtool.o hns3_debugfs.o
 
 hns3-$(CONFIG_HNS3_DCB) += hns3_dcbnl.o
+
+obj-$(CONFIG_HNS3_HCLGEVF) += hclgevf.o
+
+hclgevf-objs = hns3vf/hclgevf_main.o hns3vf/hclgevf_cmd.o hns3vf/hclgevf_mbx.o  hns3vf/hclgevf_devlink.o \
+		hns3_common/hclge_comm_cmd.o
+
+obj-$(CONFIG_HNS3_HCLGE) += hclge.o
+hclge-objs = hns3pf/hclge_main.o hns3pf/hclge_cmd.o hns3pf/hclge_mdio.o hns3pf/hclge_tm.o \
+		hns3pf/hclge_mbx.o hns3pf/hclge_err.o  hns3pf/hclge_debugfs.o hns3pf/hclge_ptp.o hns3pf/hclge_devlink.o \
+		hns3_common/hclge_comm_cmd.o
+
+hclge-$(CONFIG_HNS3_DCB) += hns3pf/hclge_dcb.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hclge_mbx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hclge_mbx.h
@@ -46,6 +46,7 @@
 	HCLGE_MBX_PUSH_PROMISC_INFO,	/* (PF -> VF) push vf promisc info */
 	HCLGE_MBX_VF_UNINIT,            /* (VF -> PF) vf is unintializing */
 	HCLGE_MBX_HANDLE_VF_TBL,	/* (VF -> PF) store/clear hw table */
+	HCLGE_MBX_GET_RING_VECTOR_MAP,	/* (VF -> PF) get ring-to-vector map */
 
 	HCLGE_MBX_GET_VF_FLR_STATUS = 200, /* (M7 -> PF) get vf flr status */
 	HCLGE_MBX_PUSH_LINK_STATUS,	/* (M7 -> PF) get port link status */
@@ -80,6 +81,9 @@
 #define HCLGE_MBX_MAX_RESP_DATA_SIZE	8U
 #define HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM	4
 
+#define HCLGE_RESET_SCHED_TIMEOUT	(3 * HZ)
+#define HCLGE_MBX_SCHED_TIMEOUT	(HZ / 2)
+
 struct hclge_ring_chain_param {
 	u8 ring_type;
 	u8 tqp_index;
@@ -131,11 +135,20 @@
 };
 
 struct hclge_pf_to_vf_msg {
-	u16 code;
-	u16 vf_mbx_msg_code;
-	u16 vf_mbx_msg_subcode;
-	u16 resp_status;
-	u8 resp_data[HCLGE_MBX_MAX_RESP_DATA_SIZE];
+	__le16 code;
+	union {
+		/* used for mbx response */
+		struct {
+			__le16 vf_mbx_msg_code;
+			__le16 vf_mbx_msg_subcode;
+			__le16 resp_status;
+			u8 resp_data[HCLGE_MBX_MAX_RESP_DATA_SIZE];
+		};
+		/* used for general mbx */
+		struct {
+			u8 msg_data[HCLGE_MBX_MAX_MSG_SIZE];
+		};
+	};
 };
 
 struct hclge_mbx_vf_to_pf_cmd {
@@ -145,7 +158,7 @@
 	u8 rsv1[1];
 	u8 msg_len;
 	u8 rsv2;
-	u16 match_id;
+	__le16 match_id;
 	struct hclge_vf_to_pf_msg msg;
 };
 
@@ -156,7 +169,7 @@
 	u8 rsv[3];
 	u8 msg_len;
 	u8 rsv1;
-	u16 match_id;
+	__le16 match_id;
 	struct hclge_pf_to_vf_msg msg;
 };
 
@@ -166,6 +179,28 @@
 	u8 rsv[22];
 };
 
+#pragma pack(1)
+struct hclge_mbx_link_status {
+	__le16 link_status;
+	__le32 speed;
+	__le16 duplex;
+	u8 flag;
+};
+
+struct hclge_mbx_link_mode {
+	__le16 idx;
+	__le64 link_mode;
+};
+
+struct hclge_mbx_port_base_vlan {
+	__le16 state;
+	__le16 vlan_proto;
+	__le16 qos;
+	__le16 vlan_tag;
+};
+
+#pragma pack()
+
 /* used by VF to store the received Async responses from PF */
 struct hclgevf_mbx_arq_ring {
 #define HCLGE_MBX_MAX_ARQ_MSG_SIZE	8
@@ -174,9 +209,20 @@
 	u32 head;
 	u32 tail;
 	atomic_t count;
-	u16 msg_q[HCLGE_MBX_MAX_ARQ_MSG_NUM][HCLGE_MBX_MAX_ARQ_MSG_SIZE];
+	__le16 msg_q[HCLGE_MBX_MAX_ARQ_MSG_NUM][HCLGE_MBX_MAX_ARQ_MSG_SIZE];
 };
 
+struct hclge_dev;
+
+#define HCLGE_MBX_OPCODE_MAX 256
+struct hclge_mbx_ops_param {
+	struct hclge_vport *vport;
+	struct hclge_mbx_vf_to_pf_cmd *req;
+	struct hclge_respond_to_vf_msg *resp_msg;
+};
+
+typedef int (*hclge_mbx_ops_fn)(struct hclge_mbx_ops_param *param);
+
 #define hclge_mbx_ring_ptr_move_crq(crq) \
 	(crq->next_to_use = (crq->next_to_use + 1) % crq->desc_num)
 #define hclge_mbx_tail_ptr_move_arq(arq) \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hnae3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hnae3.c
@@ -25,8 +25,11 @@
 		pci_id = pci_match_id(ae_algo->pdev_id_table, ae_dev->pdev);
 		if (!pci_id)
 			continue;
-		if (IS_ENABLED(CONFIG_PCI_IOV))
+		if (IS_ENABLED(CONFIG_PCI_IOV)) {
+			device_lock(&ae_dev->pdev->dev);
 			pci_disable_sriov(ae_dev->pdev);
+			device_unlock(&ae_dev->pdev->dev);
+		}
 	}
 }
 EXPORT_SYMBOL(hnae3_unregister_ae_algo_prepare);
@@ -37,6 +40,21 @@
  */
 static DEFINE_MUTEX(hnae3_common_lock);
 
+/* ensure the drivers being unloaded one by one */
+static DEFINE_MUTEX(hnae3_unload_lock);
+
+void hnae3_acquire_unload_lock(void)
+{
+	mutex_lock(&hnae3_unload_lock);
+}
+EXPORT_SYMBOL(hnae3_acquire_unload_lock);
+
+void hnae3_release_unload_lock(void)
+{
+	mutex_unlock(&hnae3_unload_lock);
+}
+EXPORT_SYMBOL(hnae3_release_unload_lock);
+
 static bool hnae3_client_match(enum hnae3_client_type client_type)
 {
 	if (client_type == HNAE3_CLIENT_KNIC ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hnae3.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hnae3.h
@@ -341,6 +341,7 @@
 	u8 max_non_tso_bd_num; /* max BD number of one non-TSO packet */
 	u16 max_frm_size;
 	u16 max_qset_num;
+	u16 umv_size;
 };
 
 struct hnae3_client_ops {
@@ -527,6 +528,8 @@
  *   Get 1588 rx hwstamp
  * get_ts_info
  *   Get phc info
+ * clean_vf_config
+ *   Clean residual vf info after disable sriov
  */
 struct hnae3_ae_ops {
 	int (*init_ae_dev)(struct hnae3_ae_dev *ae_dev);
@@ -588,7 +591,7 @@
 				   u32 *tx_usecs_high, u32 *rx_usecs_high);
 
 	void (*get_mac_addr)(struct hnae3_handle *handle, u8 *p);
-	int (*set_mac_addr)(struct hnae3_handle *handle, void *p,
+	int (*set_mac_addr)(struct hnae3_handle *handle, const void *p,
 			    bool is_first);
 	int (*do_ioctl)(struct hnae3_handle *handle,
 			struct ifreq *ifr, int cmd);
@@ -720,6 +723,7 @@
 			   struct ethtool_ts_info *info);
 	int (*get_link_diagnosis_info)(struct hnae3_handle *handle,
 				       u32 *status_code);
+	void (*clean_vf_config)(struct hnae3_ae_dev *ae_dev, int num_vfs);
 };
 
 struct hnae3_dcb_ops {
@@ -754,6 +758,7 @@
 	u16 tqp_offset[HNAE3_MAX_TC];
 	u8 num_tc; /* Total number of enabled TCs */
 	bool mqprio_active;
+	bool dcb_ets_active;
 };
 
 struct hnae3_knic_private_info {
@@ -824,12 +829,15 @@
 		struct hnae3_roce_private_info rinfo;
 	};
 
-	u32 numa_node_mask;	/* for multi-chip support */
+	nodemask_t numa_node_mask; /* for multi-chip support */
 
 	enum hnae3_port_base_vlan_state port_base_vlan_state;
 
 	u8 netdev_flags;
 	struct dentry *hnae3_dbgfs;
+	/* protects concurrent contention between debugfs commands */
+	struct mutex dbgfs_lock;
+	char **dbgfs_buf;
 
 	/* Network interface message level enabled bits */
 	u32 msg_enable;
@@ -850,6 +858,20 @@
 #define hnae3_get_bit(origin, shift) \
 	hnae3_get_field(origin, 0x1 << (shift), shift)
 
+#define HNAE3_FORMAT_MAC_ADDR_LEN	18
+#define HNAE3_FORMAT_MAC_ADDR_OFFSET_0	0
+#define HNAE3_FORMAT_MAC_ADDR_OFFSET_4	4
+#define HNAE3_FORMAT_MAC_ADDR_OFFSET_5	5
+
+static inline void hnae3_format_mac_addr(char *format_mac_addr,
+					 const u8 *mac_addr)
+{
+	snprintf(format_mac_addr, HNAE3_FORMAT_MAC_ADDR_LEN, "%02x:**:**:**:%02x:%02x",
+		 mac_addr[HNAE3_FORMAT_MAC_ADDR_OFFSET_0],
+		 mac_addr[HNAE3_FORMAT_MAC_ADDR_OFFSET_4],
+		 mac_addr[HNAE3_FORMAT_MAC_ADDR_OFFSET_5]);
+}
+
 int hnae3_register_ae_dev(struct hnae3_ae_dev *ae_dev);
 void hnae3_unregister_ae_dev(struct hnae3_ae_dev *ae_dev);
 
@@ -863,4 +885,6 @@
 void hnae3_set_client_init_flag(struct hnae3_client *client,
 				struct hnae3_ae_dev *ae_dev,
 				unsigned int inited);
+void hnae3_acquire_unload_lock(void);
+void hnae3_release_unload_lock(void);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_common/hclge_comm_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_common/hclge_comm_cmd.c
@@ -0,0 +1,259 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021-2021 Hisilicon Limited.
+
+#include "hnae3.h"
+#include "hclge_comm_cmd.h"
+
+static bool hclge_is_elem_in_array(const u16 *spec_opcode, u32 size, u16 opcode)
+{
+	u32 i;
+
+	for (i = 0; i < size; i++) {
+		if (spec_opcode[i] == opcode)
+			return true;
+	}
+
+	return false;
+}
+
+static const u16 pf_spec_opcode[] = { HCLGE_COMM_OPC_STATS_64_BIT,
+				      HCLGE_COMM_OPC_STATS_32_BIT,
+				      HCLGE_COMM_OPC_STATS_MAC,
+				      HCLGE_COMM_OPC_STATS_MAC_ALL,
+				      HCLGE_COMM_OPC_QUERY_32_BIT_REG,
+				      HCLGE_COMM_OPC_QUERY_64_BIT_REG,
+				      HCLGE_COMM_QUERY_CLEAR_MPF_RAS_INT,
+				      HCLGE_COMM_QUERY_CLEAR_PF_RAS_INT,
+				      HCLGE_COMM_QUERY_CLEAR_ALL_MPF_MSIX_INT,
+				      HCLGE_COMM_QUERY_CLEAR_ALL_PF_MSIX_INT,
+				      HCLGE_COMM_QUERY_ALL_ERR_INFO };
+
+static const u16 vf_spec_opcode[] = { HCLGE_COMM_OPC_STATS_64_BIT,
+				      HCLGE_COMM_OPC_STATS_32_BIT,
+				      HCLGE_COMM_OPC_STATS_MAC };
+
+static bool hclge_comm_is_special_opcode(u16 opcode, bool is_pf)
+{
+	/* these commands have several descriptors,
+	 * and use the first one to save opcode and return value
+	 */
+	const u16 *spec_opcode = is_pf ? pf_spec_opcode : vf_spec_opcode;
+	u32 size = is_pf ? ARRAY_SIZE(pf_spec_opcode) :
+				ARRAY_SIZE(vf_spec_opcode);
+
+	return hclge_is_elem_in_array(spec_opcode, size, opcode);
+}
+
+static int hclge_comm_ring_space(struct hclge_comm_cmq_ring *ring)
+{
+	int ntc = ring->next_to_clean;
+	int ntu = ring->next_to_use;
+	int used = (ntu - ntc + ring->desc_num) % ring->desc_num;
+
+	return ring->desc_num - used - 1;
+}
+
+static void hclge_comm_cmd_copy_desc(struct hclge_comm_hw *hw,
+				     struct hclge_desc *desc, int num)
+{
+	struct hclge_desc *desc_to_use;
+	int handle = 0;
+
+	while (handle < num) {
+		desc_to_use = &hw->cmq.csq.desc[hw->cmq.csq.next_to_use];
+		*desc_to_use = desc[handle];
+		(hw->cmq.csq.next_to_use)++;
+		if (hw->cmq.csq.next_to_use >= hw->cmq.csq.desc_num)
+			hw->cmq.csq.next_to_use = 0;
+		handle++;
+	}
+}
+
+static int hclge_comm_is_valid_csq_clean_head(struct hclge_comm_cmq_ring *ring,
+					      int head)
+{
+	int ntc = ring->next_to_clean;
+	int ntu = ring->next_to_use;
+
+	if (ntu > ntc)
+		return head >= ntc && head <= ntu;
+
+	return head >= ntc || head <= ntu;
+}
+
+static int hclge_comm_cmd_csq_clean(struct hclge_comm_hw *hw)
+{
+	struct hclge_comm_cmq_ring *csq = &hw->cmq.csq;
+	int clean;
+	u32 head;
+
+	head = hclge_comm_read_dev(hw, HCLGE_COMM_NIC_CSQ_HEAD_REG);
+	rmb(); /* Make sure head is ready before touch any data */
+
+	if (!hclge_comm_is_valid_csq_clean_head(csq, head)) {
+		dev_warn(&hw->cmq.csq.pdev->dev, "wrong cmd head (%u, %d-%d)\n",
+			 head, csq->next_to_use, csq->next_to_clean);
+		dev_warn(&hw->cmq.csq.pdev->dev,
+			 "Disabling any further commands to IMP firmware\n");
+		set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hw->comm_state);
+		dev_warn(&hw->cmq.csq.pdev->dev,
+			 "IMP firmware watchdog reset soon expected!\n");
+		return -EIO;
+	}
+
+	clean = (head - csq->next_to_clean + csq->desc_num) % csq->desc_num;
+	csq->next_to_clean = head;
+	return clean;
+}
+
+static int hclge_comm_cmd_csq_done(struct hclge_comm_hw *hw)
+{
+	u32 head = hclge_comm_read_dev(hw, HCLGE_COMM_NIC_CSQ_HEAD_REG);
+	return head == hw->cmq.csq.next_to_use;
+}
+
+static void hclge_comm_wait_for_resp(struct hclge_comm_hw *hw,
+				     bool *is_completed)
+{
+	u32 timeout = 0;
+
+	do {
+		if (hclge_comm_cmd_csq_done(hw)) {
+			*is_completed = true;
+			break;
+		}
+		udelay(1);
+		timeout++;
+	} while (timeout < hw->cmq.tx_timeout);
+}
+
+static int hclge_comm_cmd_convert_err_code(u16 desc_ret)
+{
+	struct hclge_comm_errcode hclge_comm_cmd_errcode[] = {
+		{ HCLGE_COMM_CMD_EXEC_SUCCESS, 0 },
+		{ HCLGE_COMM_CMD_NO_AUTH, -EPERM },
+		{ HCLGE_COMM_CMD_NOT_SUPPORTED, -EOPNOTSUPP },
+		{ HCLGE_COMM_CMD_QUEUE_FULL, -EXFULL },
+		{ HCLGE_COMM_CMD_NEXT_ERR, -ENOSR },
+		{ HCLGE_COMM_CMD_UNEXE_ERR, -ENOTBLK },
+		{ HCLGE_COMM_CMD_PARA_ERR, -EINVAL },
+		{ HCLGE_COMM_CMD_RESULT_ERR, -ERANGE },
+		{ HCLGE_COMM_CMD_TIMEOUT, -ETIME },
+		{ HCLGE_COMM_CMD_HILINK_ERR, -ENOLINK },
+		{ HCLGE_COMM_CMD_QUEUE_ILLEGAL, -ENXIO },
+		{ HCLGE_COMM_CMD_INVALID, -EBADR },
+	};
+	u32 errcode_count = ARRAY_SIZE(hclge_comm_cmd_errcode);
+	u32 i;
+
+	for (i = 0; i < errcode_count; i++)
+		if (hclge_comm_cmd_errcode[i].imp_errcode == desc_ret)
+			return hclge_comm_cmd_errcode[i].common_errno;
+
+	return -EIO;
+}
+
+static int hclge_comm_cmd_check_retval(struct hclge_comm_hw *hw,
+				       struct hclge_desc *desc, int num,
+				       int ntc, bool is_pf)
+{
+	u16 opcode, desc_ret;
+	int handle;
+
+	opcode = le16_to_cpu(desc[0].opcode);
+	for (handle = 0; handle < num; handle++) {
+		desc[handle] = hw->cmq.csq.desc[ntc];
+		ntc++;
+		if (ntc >= hw->cmq.csq.desc_num)
+			ntc = 0;
+	}
+	if (likely(!hclge_comm_is_special_opcode(opcode, is_pf)))
+		desc_ret = le16_to_cpu(desc[num - 1].retval);
+	else
+		desc_ret = le16_to_cpu(desc[0].retval);
+
+	hw->cmq.last_status = desc_ret;
+
+	return hclge_comm_cmd_convert_err_code(desc_ret);
+}
+
+static int hclge_comm_cmd_check_result(struct hclge_comm_hw *hw,
+				       struct hclge_desc *desc,
+				       int num, int ntc, bool is_pf)
+{
+	bool is_completed = false;
+	int handle, ret;
+
+	/* If the command is sync, wait for the firmware to write back,
+	 * if multi descriptors to be sent, use the first one to check
+	 */
+	if (HCLGE_COMM_SEND_SYNC(le16_to_cpu(desc->flag)))
+		hclge_comm_wait_for_resp(hw, &is_completed);
+
+	if (!is_completed)
+		ret = -EBADE;
+	else
+		ret = hclge_comm_cmd_check_retval(hw, desc, num, ntc, is_pf);
+
+	/* Clean the command send queue */
+	handle = hclge_comm_cmd_csq_clean(hw);
+	if (handle < 0)
+		ret = handle;
+	else if (handle != num)
+		dev_warn(&hw->cmq.csq.pdev->dev,
+			 "cleaned %d, need to clean %d\n", handle, num);
+	return ret;
+}
+
+/**
+ * hclge_comm_cmd_send - send command to command queue
+ * @hw: pointer to the hw struct
+ * @desc: prefilled descriptor for describing the command
+ * @num : the number of descriptors to be sent
+ * @is_pf: bool to judge pf/vf module
+ *
+ * This is the main send command for command queue, it
+ * sends the queue, cleans the queue, etc
+ **/
+int hclge_comm_cmd_send(struct hclge_comm_hw *hw, struct hclge_desc *desc,
+			int num, bool is_pf)
+{
+	struct hclge_comm_cmq_ring *csq = &hw->cmq.csq;
+	int ret;
+	int ntc;
+
+	spin_lock_bh(&hw->cmq.csq.lock);
+
+	if (test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hw->comm_state)) {
+		spin_unlock_bh(&hw->cmq.csq.lock);
+		return -EBUSY;
+	}
+
+	if (num > hclge_comm_ring_space(&hw->cmq.csq)) {
+		/* If CMDQ ring is full, SW HEAD and HW HEAD may be different,
+		 * need update the SW HEAD pointer csq->next_to_clean
+		 */
+		csq->next_to_clean =
+			hclge_comm_read_dev(hw, HCLGE_COMM_NIC_CSQ_HEAD_REG);
+		spin_unlock_bh(&hw->cmq.csq.lock);
+		return -EBUSY;
+	}
+
+	/**
+	 * Record the location of desc in the ring for this time
+	 * which will be use for hardware to write back
+	 */
+	ntc = hw->cmq.csq.next_to_use;
+
+	hclge_comm_cmd_copy_desc(hw, desc, num);
+
+	/* Write to hardware */
+	hclge_comm_write_dev(hw, HCLGE_COMM_NIC_CSQ_TAIL_REG,
+			     hw->cmq.csq.next_to_use);
+
+	ret = hclge_comm_cmd_check_result(hw, desc, num, ntc, is_pf);
+
+	spin_unlock_bh(&hw->cmq.csq.lock);
+
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_common/hclge_comm_cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_common/hclge_comm_cmd.h
@@ -0,0 +1,121 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+// Copyright (c) 2021-2021 Hisilicon Limited.
+
+#ifndef __HCLGE_COMM_CMD_H
+#define __HCLGE_COMM_CMD_H
+#include <linux/types.h>
+
+#include "hnae3.h"
+
+#define HCLGE_COMM_CMD_FLAG_NO_INTR		BIT(4)
+
+#define HCLGE_COMM_SEND_SYNC(flag) \
+	((flag) & HCLGE_COMM_CMD_FLAG_NO_INTR)
+
+#define HCLGE_COMM_NIC_CSQ_TAIL_REG		0x27010
+#define HCLGE_COMM_NIC_CSQ_HEAD_REG		0x27014
+
+enum hclge_comm_cmd_return_status {
+	HCLGE_COMM_CMD_EXEC_SUCCESS	= 0,
+	HCLGE_COMM_CMD_NO_AUTH		= 1,
+	HCLGE_COMM_CMD_NOT_SUPPORTED	= 2,
+	HCLGE_COMM_CMD_QUEUE_FULL	= 3,
+	HCLGE_COMM_CMD_NEXT_ERR		= 4,
+	HCLGE_COMM_CMD_UNEXE_ERR	= 5,
+	HCLGE_COMM_CMD_PARA_ERR		= 6,
+	HCLGE_COMM_CMD_RESULT_ERR	= 7,
+	HCLGE_COMM_CMD_TIMEOUT		= 8,
+	HCLGE_COMM_CMD_HILINK_ERR	= 9,
+	HCLGE_COMM_CMD_QUEUE_ILLEGAL	= 10,
+	HCLGE_COMM_CMD_INVALID		= 11,
+};
+
+enum hclge_comm_special_cmd {
+	HCLGE_COMM_OPC_STATS_64_BIT		= 0x0030,
+	HCLGE_COMM_OPC_STATS_32_BIT		= 0x0031,
+	HCLGE_COMM_OPC_STATS_MAC		= 0x0032,
+	HCLGE_COMM_OPC_STATS_MAC_ALL		= 0x0034,
+	HCLGE_COMM_OPC_QUERY_32_BIT_REG		= 0x0041,
+	HCLGE_COMM_OPC_QUERY_64_BIT_REG		= 0x0042,
+	HCLGE_COMM_QUERY_CLEAR_MPF_RAS_INT	= 0x1511,
+	HCLGE_COMM_QUERY_CLEAR_PF_RAS_INT	= 0x1512,
+	HCLGE_COMM_QUERY_CLEAR_ALL_MPF_MSIX_INT	= 0x1514,
+	HCLGE_COMM_QUERY_CLEAR_ALL_PF_MSIX_INT	= 0x1515,
+	HCLGE_COMM_QUERY_ALL_ERR_INFO		= 0x1517,
+};
+
+enum hclge_comm_cmd_state {
+	HCLGE_COMM_STATE_CMD_DISABLE,
+};
+
+struct hclge_comm_errcode {
+	u32 imp_errcode;
+	int common_errno;
+};
+
+#define HCLGE_DESC_DATA_LEN		6
+struct hclge_desc {
+	__le16 opcode;
+	__le16 flag;
+	__le16 retval;
+	__le16 rsv;
+	__le32 data[HCLGE_DESC_DATA_LEN];
+};
+
+struct hclge_comm_cmq_ring {
+	dma_addr_t desc_dma_addr;
+	struct hclge_desc *desc;
+	struct pci_dev *pdev;
+	u32 head;
+	u32 tail;
+
+	u16 buf_size;
+	u16 desc_num;
+	int next_to_use;
+	int next_to_clean;
+	u8 ring_type; /* cmq ring type */
+	spinlock_t lock; /* Command queue lock */
+};
+
+enum hclge_comm_cmd_status {
+	HCLGE_COMM_STATUS_SUCCESS	= 0,
+	HCLGE_COMM_ERR_CSQ_FULL		= -1,
+	HCLGE_COMM_ERR_CSQ_TIMEOUT	= -2,
+	HCLGE_COMM_ERR_CSQ_ERROR	= -3,
+};
+
+struct hclge_comm_cmq {
+	struct hclge_comm_cmq_ring csq;
+	struct hclge_comm_cmq_ring crq;
+	u16 tx_timeout;
+	enum hclge_comm_cmd_status last_status;
+};
+
+struct hclge_comm_hw {
+	void __iomem *io_base;
+	void __iomem *mem_base;
+	struct hclge_comm_cmq cmq;
+	unsigned long comm_state;
+};
+
+static inline void hclge_comm_write_reg(void __iomem *base, u32 reg, u32 value)
+{
+	writel(value, base + reg);
+}
+
+static inline u32 hclge_comm_read_reg(u8 __iomem *base, u32 reg)
+{
+	u8 __iomem *reg_addr = READ_ONCE(base);
+
+	return readl(reg_addr + reg);
+}
+
+#define hclge_comm_write_dev(a, reg, value) \
+	hclge_comm_write_reg((a)->io_base, reg, value)
+#define hclge_comm_read_dev(a, reg) \
+	hclge_comm_read_reg((a)->io_base, reg)
+
+int hclge_comm_cmd_send(struct hclge_comm_hw *hw, struct hclge_desc *desc,
+			int num, bool is_pf);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_debugfs.c
@@ -123,7 +123,7 @@
 		.name = "tx_bd_queue",
 		.cmd = HNAE3_DBG_CMD_TX_BD,
 		.dentry = HNS3_DBG_DENTRY_TX_BD,
-		.buf_len = HNS3_DBG_READ_LEN_4MB,
+		.buf_len = HNS3_DBG_READ_LEN_5MB,
 		.init = hns3_dbg_bd_file_init,
 	},
 	{
@@ -924,6 +924,8 @@
 			  dev_specs->max_tm_rate);
 	*pos += scnprintf(buf + *pos, len - *pos, "MAX QSET number: %u\n",
 			  dev_specs->max_qset_num);
+	*pos += scnprintf(buf + *pos, len - *pos, "umv size: %u\n",
+			  dev_specs->umv_size);
 }
 
 static int hns3_dbg_dev_info(struct hnae3_handle *h, char *buf, int len)
@@ -1021,7 +1023,8 @@
 	if (ret)
 		return ret;
 
-	save_buf = &hns3_dbg_cmd[index].buf;
+	mutex_lock(&handle->dbgfs_lock);
+	save_buf = &handle->dbgfs_buf[index];
 
 	if (!test_bit(HNS3_NIC_STATE_INITED, &priv->state) ||
 	    test_bit(HNS3_NIC_STATE_RESETTING, &priv->state)) {
@@ -1033,15 +1036,15 @@
 		read_buf = *save_buf;
 	} else {
 		read_buf = kvzalloc(hns3_dbg_cmd[index].buf_len, GFP_KERNEL);
-		if (!read_buf)
-			return -ENOMEM;
+		if (!read_buf) {
+			ret = -ENOMEM;
+			goto out;
+		}
 
 		/* save the buffer addr until the last read operation */
 		*save_buf = read_buf;
-	}
 
-	/* get data ready for the first time to read */
-	if (!*ppos) {
+		/* get data ready for the first time to read */
 		ret = hns3_dbg_read_cmd(dbg_data, hns3_dbg_cmd[index].cmd,
 					read_buf, hns3_dbg_cmd[index].buf_len);
 		if (ret)
@@ -1050,8 +1053,10 @@
 
 	size = simple_read_from_buffer(buffer, count, ppos, read_buf,
 				       strlen(read_buf));
-	if (size > 0)
+	if (size > 0) {
+		mutex_unlock(&handle->dbgfs_lock);
 		return size;
+	}
 
 out:
 	/* free the buffer for the last read operation */
@@ -1060,6 +1065,7 @@
 		*save_buf = NULL;
 	}
 
+	mutex_unlock(&handle->dbgfs_lock);
 	return ret;
 }
 
@@ -1123,6 +1129,13 @@
 	int ret;
 	u32 i;
 
+	handle->dbgfs_buf = devm_kcalloc(&handle->pdev->dev,
+					 ARRAY_SIZE(hns3_dbg_cmd),
+					 sizeof(*handle->dbgfs_buf),
+					 GFP_KERNEL);
+	if (!handle->dbgfs_buf)
+		return -ENOMEM;
+
 	hns3_dbg_dentry[HNS3_DBG_DENTRY_COMMON].dentry =
 				debugfs_create_dir(name, hns3_dbgfs_root);
 	handle->hnae3_dbgfs = hns3_dbg_dentry[HNS3_DBG_DENTRY_COMMON].dentry;
@@ -1132,6 +1145,8 @@
 			debugfs_create_dir(hns3_dbg_dentry[i].name,
 					   handle->hnae3_dbgfs);
 
+	mutex_init(&handle->dbgfs_lock);
+
 	for (i = 0; i < ARRAY_SIZE(hns3_dbg_cmd); i++) {
 		if ((hns3_dbg_cmd[i].cmd == HNAE3_DBG_CMD_TM_NODES &&
 		     ae_dev->dev_version <= HNAE3_DEVICE_VERSION_V2) ||
@@ -1160,6 +1175,7 @@
 out:
 	debugfs_remove_recursive(handle->hnae3_dbgfs);
 	handle->hnae3_dbgfs = NULL;
+	mutex_destroy(&handle->dbgfs_lock);
 	return ret;
 }
 
@@ -1167,14 +1183,16 @@
 {
 	u32 i;
 
+	debugfs_remove_recursive(handle->hnae3_dbgfs);
+	handle->hnae3_dbgfs = NULL;
+
 	for (i = 0; i < ARRAY_SIZE(hns3_dbg_cmd); i++)
-		if (hns3_dbg_cmd[i].buf) {
-			kvfree(hns3_dbg_cmd[i].buf);
-			hns3_dbg_cmd[i].buf = NULL;
+		if (handle->dbgfs_buf[i]) {
+			kvfree(handle->dbgfs_buf[i]);
+			handle->dbgfs_buf[i] = NULL;
 		}
 
-	debugfs_remove_recursive(handle->hnae3_dbgfs);
-	handle->hnae3_dbgfs = NULL;
+	mutex_destroy(&handle->dbgfs_lock);
 }
 
 void hns3_dbg_register_debugfs(const char *debugfs_dir_name)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_debugfs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_debugfs.h
@@ -8,6 +8,7 @@
 #define HNS3_DBG_READ_LEN_128KB	0x20000
 #define HNS3_DBG_READ_LEN_1MB	0x100000
 #define HNS3_DBG_READ_LEN_4MB	0x400000
+#define HNS3_DBG_READ_LEN_5MB	0x500000
 #define HNS3_DBG_WRITE_LEN	1024
 
 #define HNS3_DBG_DATA_STR_LEN	32
@@ -47,7 +48,6 @@
 	enum hnae3_dbg_cmd cmd;
 	enum hns3_dbg_dentry_type dentry;
 	u32 buf_len;
-	char *buf;
 	int (*init)(struct hnae3_handle *handle, unsigned int cmd);
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c
@@ -1005,9 +1005,7 @@
 		return false;
 
 	if (ALIGN(len, dma_get_cache_alignment()) > space) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.tx_spare_full++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, tx_spare_full);
 		return false;
 	}
 
@@ -1024,9 +1022,7 @@
 		return false;
 
 	if (space < HNS3_MAX_SGL_SIZE) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.tx_spare_full++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, tx_spare_full);
 		return false;
 	}
 
@@ -1516,7 +1512,7 @@
 	if (unlikely(rc < 0))
 		return rc;
 
-	vhdr = (struct vlan_ethhdr *)skb->data;
+	vhdr = skb_vlan_eth_hdr(skb);
 	vhdr->h_vlan_TCI |= cpu_to_be16((skb->priority << VLAN_PRIO_SHIFT)
 					 & VLAN_PRIO_MASK);
 
@@ -1554,9 +1550,7 @@
 
 	ret = hns3_handle_vtags(ring, skb);
 	if (unlikely(ret < 0)) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.tx_vlan_err++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, tx_vlan_err);
 		return ret;
 	} else if (ret == HNS3_INNER_VLAN_TAG) {
 		inner_vtag = skb_vlan_tag_get(skb);
@@ -1591,9 +1585,7 @@
 
 		ret = hns3_get_l4_protocol(skb, &ol4_proto, &il4_proto);
 		if (unlikely(ret < 0)) {
-			u64_stats_update_begin(&ring->syncp);
-			ring->stats.tx_l4_proto_err++;
-			u64_stats_update_end(&ring->syncp);
+			hns3_ring_stats_update(ring, tx_l4_proto_err);
 			return ret;
 		}
 
@@ -1601,18 +1593,14 @@
 				      &type_cs_vlan_tso,
 				      &ol_type_vlan_len_msec);
 		if (unlikely(ret < 0)) {
-			u64_stats_update_begin(&ring->syncp);
-			ring->stats.tx_l2l3l4_err++;
-			u64_stats_update_end(&ring->syncp);
+			hns3_ring_stats_update(ring, tx_l2l3l4_err);
 			return ret;
 		}
 
 		ret = hns3_set_tso(skb, &paylen_ol4cs, &mss_hw_csum,
 				   &type_cs_vlan_tso, &desc_cb->send_bytes);
 		if (unlikely(ret < 0)) {
-			u64_stats_update_begin(&ring->syncp);
-			ring->stats.tx_tso_err++;
-			u64_stats_update_end(&ring->syncp);
+			hns3_ring_stats_update(ring, tx_tso_err);
 			return ret;
 		}
 	}
@@ -1705,9 +1693,7 @@
 	}
 
 	if (unlikely(dma_mapping_error(dev, dma))) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.sw_err_cnt++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, sw_err_cnt);
 		return -ENOMEM;
 	}
 
@@ -1853,9 +1839,7 @@
 	 * recursion level of over HNS3_MAX_RECURSION_LEVEL.
 	 */
 	if (bd_num == UINT_MAX) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.over_max_recursion++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, over_max_recursion);
 		return -ENOMEM;
 	}
 
@@ -1864,16 +1848,12 @@
 	 */
 	if (skb->len > HNS3_MAX_TSO_SIZE ||
 	    (!skb_is_gso(skb) && skb->len > HNS3_MAX_NON_TSO_SIZE)) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.hw_limitation++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, hw_limitation);
 		return -ENOMEM;
 	}
 
 	if (__skb_linearize(skb)) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.sw_err_cnt++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, sw_err_cnt);
 		return -ENOMEM;
 	}
 
@@ -1903,9 +1883,7 @@
 
 		bd_num = hns3_tx_bd_count(skb->len);
 
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.tx_copy++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, tx_copy);
 	}
 
 out:
@@ -1925,9 +1903,7 @@
 		return bd_num;
 	}
 
-	u64_stats_update_begin(&ring->syncp);
-	ring->stats.tx_busy++;
-	u64_stats_update_end(&ring->syncp);
+	hns3_ring_stats_update(ring, tx_busy);
 
 	return -EBUSY;
 }
@@ -2012,9 +1988,7 @@
 	ring->pending_buf += num;
 
 	if (!doorbell) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.tx_more++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, tx_more);
 		return;
 	}
 
@@ -2064,9 +2038,7 @@
 	ret = skb_copy_bits(skb, 0, buf, size);
 	if (unlikely(ret < 0)) {
 		hns3_tx_spare_rollback(ring, cb_len);
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.copy_bits_err++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, copy_bits_err);
 		return ret;
 	}
 
@@ -2089,9 +2061,8 @@
 	dma_sync_single_for_device(ring_to_dev(ring), dma, size,
 				   DMA_TO_DEVICE);
 
-	u64_stats_update_begin(&ring->syncp);
-	ring->stats.tx_bounce++;
-	u64_stats_update_end(&ring->syncp);
+	hns3_ring_stats_update(ring, tx_bounce);
+
 	return bd_num;
 }
 
@@ -2121,9 +2092,7 @@
 	nents = skb_to_sgvec(skb, sgt->sgl, 0, skb->len);
 	if (unlikely(nents < 0)) {
 		hns3_tx_spare_rollback(ring, cb_len);
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.skb2sgl_err++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, skb2sgl_err);
 		return -ENOMEM;
 	}
 
@@ -2132,9 +2101,7 @@
 				DMA_TO_DEVICE);
 	if (unlikely(!sgt->nents)) {
 		hns3_tx_spare_rollback(ring, cb_len);
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.map_sg_err++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, map_sg_err);
 		return -ENOMEM;
 	}
 
@@ -2146,10 +2113,7 @@
 	for (i = 0; i < sgt->nents; i++)
 		bd_num += hns3_fill_desc(ring, sg_dma_address(sgt->sgl + i),
 					 sg_dma_len(sgt->sgl + i));
-
-	u64_stats_update_begin(&ring->syncp);
-	ring->stats.tx_sgl++;
-	u64_stats_update_end(&ring->syncp);
+	hns3_ring_stats_update(ring, tx_sgl);
 
 	return bd_num;
 }
@@ -2188,9 +2152,7 @@
 	if (skb_put_padto(skb, HNS3_MIN_TX_LEN)) {
 		hns3_tx_doorbell(ring, 0, !netdev_xmit_more());
 
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.sw_err_cnt++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, sw_err_cnt);
 
 		return NETDEV_TX_OK;
 	}
@@ -2255,6 +2217,8 @@
 
 static int hns3_nic_net_set_mac_address(struct net_device *netdev, void *p)
 {
+	char format_mac_addr_perm[HNAE3_FORMAT_MAC_ADDR_LEN];
+	char format_mac_addr_sa[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hnae3_handle *h = hns3_get_handle(netdev);
 	struct sockaddr *mac_addr = p;
 	int ret;
@@ -2263,8 +2227,9 @@
 		return -EADDRNOTAVAIL;
 
 	if (ether_addr_equal(netdev->dev_addr, mac_addr->sa_data)) {
-		netdev_info(netdev, "already using mac address %pM\n",
-			    mac_addr->sa_data);
+		hnae3_format_mac_addr(format_mac_addr_sa, mac_addr->sa_data);
+		netdev_info(netdev, "already using mac address %s\n",
+			    format_mac_addr_sa);
 		return 0;
 	}
 
@@ -2273,8 +2238,10 @@
 	 */
 	if (!hns3_is_phys_func(h->pdev) &&
 	    !is_zero_ether_addr(netdev->perm_addr)) {
-		netdev_err(netdev, "has permanent MAC %pM, user MAC %pM not allow\n",
-			   netdev->perm_addr, mac_addr->sa_data);
+		hnae3_format_mac_addr(format_mac_addr_perm, netdev->perm_addr);
+		hnae3_format_mac_addr(format_mac_addr_sa, mac_addr->sa_data);
+		netdev_err(netdev, "has permanent MAC %s, user MAC %s not allow\n",
+			   format_mac_addr_perm, format_mac_addr_sa);
 		return -EPERM;
 	}
 
@@ -2284,7 +2251,7 @@
 		return ret;
 	}
 
-	ether_addr_copy(netdev->dev_addr, mac_addr->sa_data);
+	eth_hw_addr_set(netdev, mac_addr->sa_data);
 
 	return 0;
 }
@@ -2836,14 +2803,16 @@
 static int hns3_nic_set_vf_mac(struct net_device *netdev, int vf_id, u8 *mac)
 {
 	struct hnae3_handle *h = hns3_get_handle(netdev);
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 
 	if (!h->ae_algo->ops->set_vf_mac)
 		return -EOPNOTSUPP;
 
 	if (is_multicast_ether_addr(mac)) {
+		hnae3_format_mac_addr(format_mac_addr, mac);
 		netdev_err(netdev,
-			   "Invalid MAC:%pM specified. Could not set MAC\n",
-			   mac);
+			   "Invalid MAC:%s specified. Could not set MAC\n",
+			   format_mac_addr);
 		return -EINVAL;
 	}
 
@@ -2947,6 +2916,21 @@
 	return ret;
 }
 
+/**
+ * hns3_clean_vf_config
+ * @pdev: pointer to a pci_dev structure
+ * @num_vfs: number of VFs allocated
+ *
+ * Clean residual vf config after disable sriov
+ **/
+static void hns3_clean_vf_config(struct pci_dev *pdev, int num_vfs)
+{
+	struct hnae3_ae_dev *ae_dev = pci_get_drvdata(pdev);
+
+	if (ae_dev->ops->clean_vf_config)
+		ae_dev->ops->clean_vf_config(ae_dev, num_vfs);
+}
+
 /* hns3_remove - Device removal routine
  * @pdev: PCI device information struct
  */
@@ -2985,7 +2969,10 @@
 		else
 			return num_vfs;
 	} else if (!pci_vfs_assigned(pdev)) {
+		int num_vfs_pre = pci_num_vf(pdev);
+
 		pci_disable_sriov(pdev);
+		hns3_clean_vf_config(pdev, num_vfs_pre);
 	} else {
 		dev_warn(&pdev->dev,
 			 "Unable to free VFs because some are assigned to VMs.\n");
@@ -3131,8 +3118,6 @@
 
 	netdev->priv_flags |= IFF_UNICAST_FLT;
 
-	netdev->gso_partial_features |= NETIF_F_GSO_GRE_CSUM;
-
 	netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER |
 		NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX |
 		NETIF_F_RXCSUM | NETIF_F_SG | NETIF_F_GSO |
@@ -3171,6 +3156,15 @@
 		  NETIF_F_HW_TC);
 
 	netdev->hw_enc_features |= netdev->vlan_features | NETIF_F_TSO_MANGLEID;
+
+	/* The device_version V3 hardware can't offload the checksum for IP in
+	 * GRE packets, but can do it for NvGRE. So default to disable the
+	 * checksum and GSO offload for GRE.
+	 */
+	if (ae_dev->dev_version > HNAE3_DEVICE_VERSION_V2) {
+		netdev->features &= ~NETIF_F_GSO_GRE;
+		netdev->features &= ~NETIF_F_GSO_GRE_CSUM;
+	}
 }
 
 static int hns3_alloc_buffer(struct hns3_enet_ring *ring,
@@ -3348,6 +3342,9 @@
 		ret = hns3_alloc_and_attach_buffer(ring, i);
 		if (ret)
 			goto out_buffer_fail;
+
+		if (!(i % HNS3_RESCHED_BD_NUM))
+			cond_resched();
 	}
 
 	return 0;
@@ -3497,17 +3494,13 @@
 	for (i = 0; i < cleand_count; i++) {
 		desc_cb = &ring->desc_cb[ring->next_to_use];
 		if (desc_cb->reuse_flag) {
-			u64_stats_update_begin(&ring->syncp);
-			ring->stats.reuse_pg_cnt++;
-			u64_stats_update_end(&ring->syncp);
+			hns3_ring_stats_update(ring, reuse_pg_cnt);
 
 			hns3_reuse_buffer(ring, ring->next_to_use);
 		} else {
 			ret = hns3_alloc_and_map_buffer(ring, &res_cbs);
 			if (ret) {
-				u64_stats_update_begin(&ring->syncp);
-				ring->stats.sw_err_cnt++;
-				u64_stats_update_end(&ring->syncp);
+				hns3_ring_stats_update(ring, sw_err_cnt);
 
 				hns3_rl_err(ring_to_netdev(ring),
 					    "alloc rx buffer failed: %d\n",
@@ -3519,9 +3512,7 @@
 			}
 			hns3_replace_buffer(ring, ring->next_to_use, &res_cbs);
 
-			u64_stats_update_begin(&ring->syncp);
-			ring->stats.non_reuse_pg++;
-			u64_stats_update_end(&ring->syncp);
+			hns3_ring_stats_update(ring, non_reuse_pg);
 		}
 
 		ring_ptr_move_fw(ring, next_to_use);
@@ -3536,6 +3527,34 @@
 	return page_count(cb->priv) == cb->pagecnt_bias;
 }
 
+static int hns3_handle_rx_copybreak(struct sk_buff *skb, int i,
+				    struct hns3_enet_ring *ring,
+				    int pull_len,
+				    struct hns3_desc_cb *desc_cb)
+{
+	struct hns3_desc *desc = &ring->desc[ring->next_to_clean];
+	u32 frag_offset = desc_cb->page_offset + pull_len;
+	int size = le16_to_cpu(desc->rx.size);
+	u32 frag_size = size - pull_len;
+	void *frag = napi_alloc_frag(frag_size);
+
+	if (unlikely(!frag)) {
+		hns3_ring_stats_update(ring, frag_alloc_err);
+
+		hns3_rl_err(ring_to_netdev(ring),
+			    "failed to allocate rx frag\n");
+		return -ENOMEM;
+	}
+
+	desc_cb->reuse_flag = 1;
+	memcpy(frag, desc_cb->buf + frag_offset, frag_size);
+	skb_add_rx_frag(skb, i, virt_to_page(frag),
+			offset_in_page(frag), frag_size, frag_size);
+
+	hns3_ring_stats_update(ring, frag_alloc);
+	return 0;
+}
+
 static void hns3_nic_reuse_page(struct sk_buff *skb, int i,
 				struct hns3_enet_ring *ring, int pull_len,
 				struct hns3_desc_cb *desc_cb)
@@ -3545,6 +3564,7 @@
 	int size = le16_to_cpu(desc->rx.size);
 	u32 truesize = hns3_buf_size(ring);
 	u32 frag_size = size - pull_len;
+	int ret = 0;
 	bool reused;
 
 	if (ring->page_pool) {
@@ -3579,27 +3599,9 @@
 		desc_cb->page_offset = 0;
 		desc_cb->reuse_flag = 1;
 	} else if (frag_size <= ring->rx_copybreak) {
-		void *frag = napi_alloc_frag(frag_size);
-
-		if (unlikely(!frag)) {
-			u64_stats_update_begin(&ring->syncp);
-			ring->stats.frag_alloc_err++;
-			u64_stats_update_end(&ring->syncp);
-
-			hns3_rl_err(ring_to_netdev(ring),
-				    "failed to allocate rx frag\n");
-			goto out;
-		}
-
-		desc_cb->reuse_flag = 1;
-		memcpy(frag, desc_cb->buf + frag_offset, frag_size);
-		skb_add_rx_frag(skb, i, virt_to_page(frag),
-				offset_in_page(frag), frag_size, frag_size);
-
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.frag_alloc++;
-		u64_stats_update_end(&ring->syncp);
-		return;
+		ret = hns3_handle_rx_copybreak(skb, i, ring, pull_len, desc_cb);
+		if (!ret)
+			return;
 	}
 
 out:
@@ -3675,20 +3677,16 @@
 	return 0;
 }
 
-static bool hns3_checksum_complete(struct hns3_enet_ring *ring,
+static void hns3_checksum_complete(struct hns3_enet_ring *ring,
 				   struct sk_buff *skb, u32 ptype, u16 csum)
 {
 	if (ptype == HNS3_INVALID_PTYPE ||
 	    hns3_rx_ptype_tbl[ptype].ip_summed != CHECKSUM_COMPLETE)
-		return false;
+		return;
 
-	u64_stats_update_begin(&ring->syncp);
-	ring->stats.csum_complete++;
-	u64_stats_update_end(&ring->syncp);
+	hns3_ring_stats_update(ring, csum_complete);
 	skb->ip_summed = CHECKSUM_COMPLETE;
 	skb->csum = csum_unfold((__force __sum16)csum);
-
-	return true;
 }
 
 static void hns3_rx_handle_csum(struct sk_buff *skb, u32 l234info,
@@ -3748,8 +3746,7 @@
 		ptype = hnae3_get_field(ol_info, HNS3_RXD_PTYPE_M,
 					HNS3_RXD_PTYPE_S);
 
-	if (hns3_checksum_complete(ring, skb, ptype, csum))
-		return;
+	hns3_checksum_complete(ring, skb, ptype, csum);
 
 	/* check if hardware has done checksum */
 	if (!(bd_base_info & BIT(HNS3_RXD_L3L4P_B)))
@@ -3758,9 +3755,8 @@
 	if (unlikely(l234info & (BIT(HNS3_RXD_L3E_B) | BIT(HNS3_RXD_L4E_B) |
 				 BIT(HNS3_RXD_OL3E_B) |
 				 BIT(HNS3_RXD_OL4E_B)))) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.l3l4_csum_err++;
-		u64_stats_update_end(&ring->syncp);
+		skb->ip_summed = CHECKSUM_NONE;
+		hns3_ring_stats_update(ring, l3l4_csum_err);
 
 		return;
 	}
@@ -3851,10 +3847,7 @@
 	skb = ring->skb;
 	if (unlikely(!skb)) {
 		hns3_rl_err(netdev, "alloc rx skb fail\n");
-
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.sw_err_cnt++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, sw_err_cnt);
 
 		return -ENOMEM;
 	}
@@ -3885,9 +3878,7 @@
 	if (ring->page_pool)
 		skb_mark_for_recycle(skb);
 
-	u64_stats_update_begin(&ring->syncp);
-	ring->stats.seg_pkt_cnt++;
-	u64_stats_update_end(&ring->syncp);
+	hns3_ring_stats_update(ring, seg_pkt_cnt);
 
 	ring->pull_len = eth_get_headlen(netdev, va, HNS3_RX_HEAD_SIZE);
 	__skb_put(skb, ring->pull_len);
@@ -4079,9 +4070,7 @@
 	ret = hns3_set_gro_and_checksum(ring, skb, l234info,
 					bd_base_info, ol_info, csum);
 	if (unlikely(ret)) {
-		u64_stats_update_begin(&ring->syncp);
-		ring->stats.rx_err_cnt++;
-		u64_stats_update_end(&ring->syncp);
+		hns3_ring_stats_update(ring, rx_err_cnt);
 		return ret;
 	}
 
@@ -4901,6 +4890,7 @@
 		}
 
 		u64_stats_init(&priv->ring[i].syncp);
+		cond_resched();
 	}
 
 	return 0;
@@ -4927,8 +4917,9 @@
 static int hns3_init_mac_addr(struct net_device *netdev)
 {
 	struct hns3_nic_priv *priv = netdev_priv(netdev);
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hnae3_handle *h = priv->ae_handle;
-	u8 mac_addr_temp[ETH_ALEN];
+	u8 mac_addr_temp[ETH_ALEN] = {0};
 	int ret = 0;
 
 	if (h->ae_algo->ops->get_mac_addr)
@@ -4937,10 +4928,11 @@
 	/* Check if the MAC address is valid, if not get a random one */
 	if (!is_valid_ether_addr(mac_addr_temp)) {
 		eth_hw_addr_random(netdev);
-		dev_warn(priv->dev, "using random MAC address %pM\n",
-			 netdev->dev_addr);
+		hnae3_format_mac_addr(format_mac_addr, netdev->dev_addr);
+		dev_warn(priv->dev, "using random MAC address %s\n",
+			 format_mac_addr);
 	} else if (!ether_addr_equal(netdev->dev_addr, mac_addr_temp)) {
-		ether_addr_copy(netdev->dev_addr, mac_addr_temp);
+		eth_hw_addr_set(netdev, mac_addr_temp);
 		ether_addr_copy(netdev->perm_addr, mac_addr_temp);
 	} else {
 		return 0;
@@ -4990,8 +4982,10 @@
 static void hns3_info_show(struct hns3_nic_priv *priv)
 {
 	struct hnae3_knic_private_info *kinfo = &priv->ae_handle->kinfo;
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 
-	dev_info(priv->dev, "MAC address: %pM\n", priv->netdev->dev_addr);
+	hnae3_format_mac_addr(format_mac_addr, priv->netdev->dev_addr);
+	dev_info(priv->dev, "MAC address: %s\n", format_mac_addr);
 	dev_info(priv->dev, "Task queue pairs numbers: %u\n", kinfo->num_tqps);
 	dev_info(priv->dev, "RSS size: %u\n", kinfo->rss_size);
 	dev_info(priv->dev, "Allocated RSS size: %u\n", kinfo->req_rss_size);
@@ -5063,6 +5057,13 @@
 		set_bit(HNS3_NIC_STATE_RXD_ADV_LAYOUT_ENABLE, &priv->state);
 }
 
+static void hns3_state_uninit(struct hnae3_handle *handle)
+{
+	struct hns3_nic_priv *priv  = handle->priv;
+
+	clear_bit(HNS3_NIC_STATE_INITED, &priv->state);
+}
+
 static int hns3_client_init(struct hnae3_handle *handle)
 {
 	struct pci_dev *pdev = handle->pdev;
@@ -5180,7 +5181,9 @@
 	return ret;
 
 out_reg_netdev_fail:
+	hns3_state_uninit(handle);
 	hns3_dbg_uninit(handle);
+	hns3_client_stop(handle);
 out_client_start:
 	hns3_free_rx_cpu_rmap(netdev);
 	hns3_nic_uninit_irq(priv);
@@ -5280,9 +5283,7 @@
 		if (!ring->desc_cb[ring->next_to_use].reuse_flag) {
 			ret = hns3_alloc_and_map_buffer(ring, &res_cbs);
 			if (ret) {
-				u64_stats_update_begin(&ring->syncp);
-				ring->stats.sw_err_cnt++;
-				u64_stats_update_end(&ring->syncp);
+				hns3_ring_stats_update(ring, sw_err_cnt);
 				/* if alloc new buffer fail, exit directly
 				 * and reclear in up flow.
 				 */
@@ -5503,6 +5504,9 @@
 	struct net_device *netdev = handle->kinfo.netdev;
 	struct hns3_nic_priv *priv = netdev_priv(netdev);
 
+	if (!test_bit(HNS3_NIC_STATE_DOWN, &priv->state))
+		hns3_nic_net_stop(netdev);
+
 	if (!test_and_clear_bit(HNS3_NIC_STATE_INITED, &priv->state)) {
 		netdev_warn(netdev, "already uninitialized\n");
 		return 0;
@@ -5716,9 +5720,11 @@
  */
 static void __exit hns3_exit_module(void)
 {
+	hnae3_acquire_unload_lock();
 	pci_unregister_driver(&hns3_driver);
 	hnae3_unregister_client(&client);
 	hns3_dbg_unregister_debugfs();
+	hnae3_release_unload_lock();
 }
 module_exit(hns3_exit_module);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_enet.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_enet.h
@@ -206,6 +206,8 @@
 #define HNS3_CQ_MODE_EQE			1U
 #define HNS3_CQ_MODE_CQE			0U
 
+#define HNS3_RESCHED_BD_NUM			1024
+
 enum hns3_pkt_l2t_type {
 	HNS3_L2_TYPE_UNICAST,
 	HNS3_L2_TYPE_MULTICAST,
@@ -654,6 +656,13 @@
 
 #define hns3_buf_size(_ring) ((_ring)->buf_size)
 
+#define hns3_ring_stats_update(ring, cnt) do { \
+	typeof(ring) (tmp) = (ring); \
+	u64_stats_update_begin(&(tmp)->syncp); \
+	((tmp)->stats.cnt)++; \
+	u64_stats_update_end(&(tmp)->syncp); \
+} while (0) \
+
 static inline unsigned int hns3_page_order(struct hns3_enet_ring *ring)
 {
 #if (PAGE_SIZE < 8192)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
@@ -739,7 +739,9 @@
 		hns3_get_ksettings(h, cmd);
 		break;
 	case HNAE3_MEDIA_TYPE_FIBER:
-		if (module_type == HNAE3_MODULE_TYPE_CR)
+		if (module_type == HNAE3_MODULE_TYPE_UNKNOWN)
+			cmd->base.port = PORT_OTHER;
+		else if (module_type == HNAE3_MODULE_TYPE_CR)
 			cmd->base.port = PORT_DA;
 		else
 			cmd->base.port = PORT_FIBRE;
@@ -985,6 +987,7 @@
 	struct hnae3_ae_dev *ae_dev = pci_get_drvdata(h->pdev);
 	const struct hnae3_ae_ops *ops = h->ae_algo->ops;
 	const struct hns3_reset_type_map *rst_type_map;
+	enum ethtool_reset_flags rst_flags;
 	u32 i, size;
 
 	if (ops->ae_dev_resetting && ops->ae_dev_resetting(h))
@@ -1004,6 +1007,7 @@
 	for (i = 0; i < size; i++) {
 		if (rst_type_map[i].rst_flags == *flags) {
 			rst_type = rst_type_map[i].rst_type;
+			rst_flags = rst_type_map[i].rst_flags;
 			break;
 		}
 	}
@@ -1019,6 +1023,8 @@
 
 	ops->reset_event(h->pdev, h);
 
+	*flags &= ~rst_flags;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c
@@ -11,46 +11,24 @@
 #include "hnae3.h"
 #include "hclge_main.h"
 
-#define cmq_ring_to_dev(ring)   (&(ring)->dev->pdev->dev)
-
-static int hclge_ring_space(struct hclge_cmq_ring *ring)
-{
-	int ntu = ring->next_to_use;
-	int ntc = ring->next_to_clean;
-	int used = (ntu - ntc + ring->desc_num) % ring->desc_num;
-
-	return ring->desc_num - used - 1;
-}
-
-static int is_valid_csq_clean_head(struct hclge_cmq_ring *ring, int head)
-{
-	int ntu = ring->next_to_use;
-	int ntc = ring->next_to_clean;
-
-	if (ntu > ntc)
-		return head >= ntc && head <= ntu;
-
-	return head >= ntc || head <= ntu;
-}
-
-static int hclge_alloc_cmd_desc(struct hclge_cmq_ring *ring)
+static int hclge_alloc_cmd_desc(struct hclge_comm_cmq_ring *ring)
 {
 	int size  = ring->desc_num * sizeof(struct hclge_desc);
 
-	ring->desc = dma_alloc_coherent(cmq_ring_to_dev(ring), size,
-					&ring->desc_dma_addr, GFP_KERNEL);
+	ring->desc = dma_alloc_coherent(&ring->pdev->dev,
+					size, &ring->desc_dma_addr, GFP_KERNEL);
 	if (!ring->desc)
 		return -ENOMEM;
 
 	return 0;
 }
 
-static void hclge_free_cmd_desc(struct hclge_cmq_ring *ring)
+static void hclge_free_cmd_desc(struct hclge_comm_cmq_ring *ring)
 {
 	int size  = ring->desc_num * sizeof(struct hclge_desc);
 
 	if (ring->desc) {
-		dma_free_coherent(cmq_ring_to_dev(ring), size,
+		dma_free_coherent(&ring->pdev->dev, size,
 				  ring->desc, ring->desc_dma_addr);
 		ring->desc = NULL;
 	}
@@ -59,12 +37,13 @@
 static int hclge_alloc_cmd_queue(struct hclge_dev *hdev, int ring_type)
 {
 	struct hclge_hw *hw = &hdev->hw;
-	struct hclge_cmq_ring *ring =
-		(ring_type == HCLGE_TYPE_CSQ) ? &hw->cmq.csq : &hw->cmq.crq;
+	struct hclge_comm_cmq_ring *ring =
+		(ring_type == HCLGE_TYPE_CSQ) ? &hw->hw.cmq.csq :
+						&hw->hw.cmq.crq;
 	int ret;
 
 	ring->ring_type = ring_type;
-	ring->dev = hdev;
+	ring->pdev = hdev->pdev;
 
 	ret = hclge_alloc_cmd_desc(ring);
 	if (ret) {
@@ -96,11 +75,10 @@
 		desc->flag |= cpu_to_le16(HCLGE_CMD_FLAG_WR);
 }
 
-static void hclge_cmd_config_regs(struct hclge_cmq_ring *ring)
+static void hclge_cmd_config_regs(struct hclge_hw *hw,
+				  struct hclge_comm_cmq_ring *ring)
 {
 	dma_addr_t dma = ring->desc_dma_addr;
-	struct hclge_dev *hdev = ring->dev;
-	struct hclge_hw *hw = &hdev->hw;
 	u32 reg_val;
 
 	if (ring->ring_type == HCLGE_TYPE_CSQ) {
@@ -128,176 +106,8 @@
 
 static void hclge_cmd_init_regs(struct hclge_hw *hw)
 {
-	hclge_cmd_config_regs(&hw->cmq.csq);
-	hclge_cmd_config_regs(&hw->cmq.crq);
-}
-
-static int hclge_cmd_csq_clean(struct hclge_hw *hw)
-{
-	struct hclge_dev *hdev = container_of(hw, struct hclge_dev, hw);
-	struct hclge_cmq_ring *csq = &hw->cmq.csq;
-	u32 head;
-	int clean;
-
-	head = hclge_read_dev(hw, HCLGE_NIC_CSQ_HEAD_REG);
-	rmb(); /* Make sure head is ready before touch any data */
-
-	if (!is_valid_csq_clean_head(csq, head)) {
-		dev_warn(&hdev->pdev->dev, "wrong cmd head (%u, %d-%d)\n", head,
-			 csq->next_to_use, csq->next_to_clean);
-		dev_warn(&hdev->pdev->dev,
-			 "Disabling any further commands to IMP firmware\n");
-		set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
-		dev_warn(&hdev->pdev->dev,
-			 "IMP firmware watchdog reset soon expected!\n");
-		return -EIO;
-	}
-
-	clean = (head - csq->next_to_clean + csq->desc_num) % csq->desc_num;
-	csq->next_to_clean = head;
-	return clean;
-}
-
-static int hclge_cmd_csq_done(struct hclge_hw *hw)
-{
-	u32 head = hclge_read_dev(hw, HCLGE_NIC_CSQ_HEAD_REG);
-	return head == hw->cmq.csq.next_to_use;
-}
-
-static bool hclge_is_special_opcode(u16 opcode)
-{
-	/* these commands have several descriptors,
-	 * and use the first one to save opcode and return value
-	 */
-	static const u16 spec_opcode[] = {
-		HCLGE_OPC_STATS_64_BIT,
-		HCLGE_OPC_STATS_32_BIT,
-		HCLGE_OPC_STATS_MAC,
-		HCLGE_OPC_STATS_MAC_ALL,
-		HCLGE_OPC_QUERY_32_BIT_REG,
-		HCLGE_OPC_QUERY_64_BIT_REG,
-		HCLGE_QUERY_CLEAR_MPF_RAS_INT,
-		HCLGE_QUERY_CLEAR_PF_RAS_INT,
-		HCLGE_QUERY_CLEAR_ALL_MPF_MSIX_INT,
-		HCLGE_QUERY_CLEAR_ALL_PF_MSIX_INT,
-		HCLGE_QUERY_ALL_ERR_INFO
-	};
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(spec_opcode); i++) {
-		if (spec_opcode[i] == opcode)
-			return true;
-	}
-
-	return false;
-}
-
-struct errcode {
-	u32 imp_errcode;
-	int common_errno;
-};
-
-static void hclge_cmd_copy_desc(struct hclge_hw *hw, struct hclge_desc *desc,
-				int num)
-{
-	struct hclge_desc *desc_to_use;
-	int handle = 0;
-
-	while (handle < num) {
-		desc_to_use = &hw->cmq.csq.desc[hw->cmq.csq.next_to_use];
-		*desc_to_use = desc[handle];
-		(hw->cmq.csq.next_to_use)++;
-		if (hw->cmq.csq.next_to_use >= hw->cmq.csq.desc_num)
-			hw->cmq.csq.next_to_use = 0;
-		handle++;
-	}
-}
-
-static int hclge_cmd_convert_err_code(u16 desc_ret)
-{
-	struct errcode hclge_cmd_errcode[] = {
-		{HCLGE_CMD_EXEC_SUCCESS, 0},
-		{HCLGE_CMD_NO_AUTH, -EPERM},
-		{HCLGE_CMD_NOT_SUPPORTED, -EOPNOTSUPP},
-		{HCLGE_CMD_QUEUE_FULL, -EXFULL},
-		{HCLGE_CMD_NEXT_ERR, -ENOSR},
-		{HCLGE_CMD_UNEXE_ERR, -ENOTBLK},
-		{HCLGE_CMD_PARA_ERR, -EINVAL},
-		{HCLGE_CMD_RESULT_ERR, -ERANGE},
-		{HCLGE_CMD_TIMEOUT, -ETIME},
-		{HCLGE_CMD_HILINK_ERR, -ENOLINK},
-		{HCLGE_CMD_QUEUE_ILLEGAL, -ENXIO},
-		{HCLGE_CMD_INVALID, -EBADR},
-	};
-	u32 errcode_count = ARRAY_SIZE(hclge_cmd_errcode);
-	u32 i;
-
-	for (i = 0; i < errcode_count; i++)
-		if (hclge_cmd_errcode[i].imp_errcode == desc_ret)
-			return hclge_cmd_errcode[i].common_errno;
-
-	return -EIO;
-}
-
-static int hclge_cmd_check_retval(struct hclge_hw *hw, struct hclge_desc *desc,
-				  int num, int ntc)
-{
-	u16 opcode, desc_ret;
-	int handle;
-
-	opcode = le16_to_cpu(desc[0].opcode);
-	for (handle = 0; handle < num; handle++) {
-		desc[handle] = hw->cmq.csq.desc[ntc];
-		ntc++;
-		if (ntc >= hw->cmq.csq.desc_num)
-			ntc = 0;
-	}
-	if (likely(!hclge_is_special_opcode(opcode)))
-		desc_ret = le16_to_cpu(desc[num - 1].retval);
-	else
-		desc_ret = le16_to_cpu(desc[0].retval);
-
-	hw->cmq.last_status = desc_ret;
-
-	return hclge_cmd_convert_err_code(desc_ret);
-}
-
-static int hclge_cmd_check_result(struct hclge_hw *hw, struct hclge_desc *desc,
-				  int num, int ntc)
-{
-	struct hclge_dev *hdev = container_of(hw, struct hclge_dev, hw);
-	bool is_completed = false;
-	u32 timeout = 0;
-	int handle, ret;
-
-	/**
-	 * If the command is sync, wait for the firmware to write back,
-	 * if multi descriptors to be sent, use the first one to check
-	 */
-	if (HCLGE_SEND_SYNC(le16_to_cpu(desc->flag))) {
-		do {
-			if (hclge_cmd_csq_done(hw)) {
-				is_completed = true;
-				break;
-			}
-			udelay(1);
-			timeout++;
-		} while (timeout < hw->cmq.tx_timeout);
-	}
-
-	if (!is_completed)
-		ret = -EBADE;
-	else
-		ret = hclge_cmd_check_retval(hw, desc, num, ntc);
-
-	/* Clean the command send queue */
-	handle = hclge_cmd_csq_clean(hw);
-	if (handle < 0)
-		ret = handle;
-	else if (handle != num)
-		dev_warn(&hdev->pdev->dev,
-			 "cleaned %d, need to clean %d\n", handle, num);
-	return ret;
+	hclge_cmd_config_regs(hw, &hw->hw.cmq.csq);
+	hclge_cmd_config_regs(hw, &hw->hw.cmq.crq);
 }
 
 /**
@@ -311,43 +121,7 @@
  **/
 int hclge_cmd_send(struct hclge_hw *hw, struct hclge_desc *desc, int num)
 {
-	struct hclge_dev *hdev = container_of(hw, struct hclge_dev, hw);
-	struct hclge_cmq_ring *csq = &hw->cmq.csq;
-	int ret;
-	int ntc;
-
-	spin_lock_bh(&hw->cmq.csq.lock);
-
-	if (test_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state)) {
-		spin_unlock_bh(&hw->cmq.csq.lock);
-		return -EBUSY;
-	}
-
-	if (num > hclge_ring_space(&hw->cmq.csq)) {
-		/* If CMDQ ring is full, SW HEAD and HW HEAD may be different,
-		 * need update the SW HEAD pointer csq->next_to_clean
-		 */
-		csq->next_to_clean = hclge_read_dev(hw, HCLGE_NIC_CSQ_HEAD_REG);
-		spin_unlock_bh(&hw->cmq.csq.lock);
-		return -EBUSY;
-	}
-
-	/**
-	 * Record the location of desc in the ring for this time
-	 * which will be use for hardware to write back
-	 */
-	ntc = hw->cmq.csq.next_to_use;
-
-	hclge_cmd_copy_desc(hw, desc, num);
-
-	/* Write to hardware */
-	hclge_write_dev(hw, HCLGE_NIC_CSQ_TAIL_REG, hw->cmq.csq.next_to_use);
-
-	ret = hclge_cmd_check_result(hw, desc, num, ntc);
-
-	spin_unlock_bh(&hw->cmq.csq.lock);
-
-	return ret;
+	return hclge_comm_cmd_send(&hw->hw, desc, num, true);
 }
 
 static void hclge_set_default_capability(struct hclge_dev *hdev)
@@ -401,7 +175,7 @@
 	return cpu_to_le32(api_caps);
 }
 
-static enum hclge_cmd_status
+static enum hclge_comm_cmd_status
 hclge_cmd_query_version_and_capability(struct hclge_dev *hdev)
 {
 	struct hnae3_ae_dev *ae_dev = pci_get_drvdata(hdev->pdev);
@@ -433,18 +207,22 @@
 
 int hclge_cmd_queue_init(struct hclge_dev *hdev)
 {
+	struct hclge_comm_cmq *cmdq = &hdev->hw.hw.cmq;
 	int ret;
 
 	/* Setup the lock for command queue */
-	spin_lock_init(&hdev->hw.cmq.csq.lock);
-	spin_lock_init(&hdev->hw.cmq.crq.lock);
+	spin_lock_init(&cmdq->csq.lock);
+	spin_lock_init(&cmdq->crq.lock);
+
+	cmdq->csq.pdev = hdev->pdev;
+	cmdq->crq.pdev = hdev->pdev;
 
 	/* Setup the queue entries for use cmd queue */
-	hdev->hw.cmq.csq.desc_num = HCLGE_NIC_CMQ_DESC_NUM;
-	hdev->hw.cmq.crq.desc_num = HCLGE_NIC_CMQ_DESC_NUM;
+	cmdq->csq.desc_num = HCLGE_NIC_CMQ_DESC_NUM;
+	cmdq->crq.desc_num = HCLGE_NIC_CMQ_DESC_NUM;
 
 	/* Setup Tx write back timeout */
-	hdev->hw.cmq.tx_timeout = HCLGE_CMDQ_TX_TIMEOUT;
+	cmdq->tx_timeout = HCLGE_CMDQ_TX_TIMEOUT;
 
 	/* Setup queue rings */
 	ret = hclge_alloc_cmd_queue(hdev, HCLGE_TYPE_CSQ);
@@ -463,7 +241,7 @@
 
 	return 0;
 err_csq:
-	hclge_free_cmd_desc(&hdev->hw.cmq.csq);
+	hclge_free_cmd_desc(&hdev->hw.hw.cmq.csq);
 	return ret;
 }
 
@@ -491,22 +269,23 @@
 
 int hclge_cmd_init(struct hclge_dev *hdev)
 {
+	struct hclge_comm_cmq *cmdq = &hdev->hw.hw.cmq;
 	int ret;
 
-	spin_lock_bh(&hdev->hw.cmq.csq.lock);
-	spin_lock(&hdev->hw.cmq.crq.lock);
+	spin_lock_bh(&cmdq->csq.lock);
+	spin_lock(&cmdq->crq.lock);
 
-	hdev->hw.cmq.csq.next_to_clean = 0;
-	hdev->hw.cmq.csq.next_to_use = 0;
-	hdev->hw.cmq.crq.next_to_clean = 0;
-	hdev->hw.cmq.crq.next_to_use = 0;
+	cmdq->csq.next_to_clean = 0;
+	cmdq->csq.next_to_use = 0;
+	cmdq->crq.next_to_clean = 0;
+	cmdq->crq.next_to_use = 0;
 
 	hclge_cmd_init_regs(&hdev->hw);
 
-	spin_unlock(&hdev->hw.cmq.crq.lock);
-	spin_unlock_bh(&hdev->hw.cmq.csq.lock);
+	spin_unlock(&cmdq->crq.lock);
+	spin_unlock_bh(&cmdq->csq.lock);
 
-	clear_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+	clear_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 
 	/* Check if there is new reset pending, because the higher level
 	 * reset may happen when lower level reset is being processed.
@@ -550,7 +329,7 @@
 	return 0;
 
 err_cmd_init:
-	set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+	set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 
 	return ret;
 }
@@ -571,19 +350,23 @@
 
 void hclge_cmd_uninit(struct hclge_dev *hdev)
 {
+	struct hclge_comm_cmq *cmdq = &hdev->hw.hw.cmq;
+
+	cmdq->csq.pdev = hdev->pdev;
+
 	hclge_firmware_compat_config(hdev, false);
 
-	set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+	set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 	/* wait to ensure that the firmware completes the possible left
 	 * over commands.
 	 */
 	msleep(HCLGE_CMDQ_CLEAR_WAIT_TIME);
-	spin_lock_bh(&hdev->hw.cmq.csq.lock);
-	spin_lock(&hdev->hw.cmq.crq.lock);
+	spin_lock_bh(&cmdq->csq.lock);
+	spin_lock(&cmdq->crq.lock);
 	hclge_cmd_uninit_regs(&hdev->hw);
-	spin_unlock(&hdev->hw.cmq.crq.lock);
-	spin_unlock_bh(&hdev->hw.cmq.csq.lock);
+	spin_unlock(&cmdq->crq.lock);
+	spin_unlock_bh(&cmdq->csq.lock);
 
-	hclge_free_cmd_desc(&hdev->hw.cmq.csq);
-	hclge_free_cmd_desc(&hdev->hw.cmq.crq);
+	hclge_free_cmd_desc(&cmdq->csq);
+	hclge_free_cmd_desc(&cmdq->crq);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
@@ -7,74 +7,22 @@
 #include <linux/io.h>
 #include <linux/etherdevice.h>
 #include "hnae3.h"
+#include "hclge_comm_cmd.h"
 
 #define HCLGE_CMDQ_TX_TIMEOUT		30000
 #define HCLGE_CMDQ_CLEAR_WAIT_TIME	200
-#define HCLGE_DESC_DATA_LEN		6
 
 struct hclge_dev;
-struct hclge_desc {
-	__le16 opcode;
 
 #define HCLGE_CMDQ_RX_INVLD_B		0
 #define HCLGE_CMDQ_RX_OUTVLD_B		1
 
-	__le16 flag;
-	__le16 retval;
-	__le16 rsv;
-	__le32 data[HCLGE_DESC_DATA_LEN];
-};
-
-struct hclge_cmq_ring {
-	dma_addr_t desc_dma_addr;
-	struct hclge_desc *desc;
-	struct hclge_dev *dev;
-	u32 head;
-	u32 tail;
-
-	u16 buf_size;
-	u16 desc_num;
-	int next_to_use;
-	int next_to_clean;
-	u8 ring_type; /* cmq ring type */
-	spinlock_t lock; /* Command queue lock */
-};
-
-enum hclge_cmd_return_status {
-	HCLGE_CMD_EXEC_SUCCESS	= 0,
-	HCLGE_CMD_NO_AUTH	= 1,
-	HCLGE_CMD_NOT_SUPPORTED	= 2,
-	HCLGE_CMD_QUEUE_FULL	= 3,
-	HCLGE_CMD_NEXT_ERR	= 4,
-	HCLGE_CMD_UNEXE_ERR	= 5,
-	HCLGE_CMD_PARA_ERR	= 6,
-	HCLGE_CMD_RESULT_ERR	= 7,
-	HCLGE_CMD_TIMEOUT	= 8,
-	HCLGE_CMD_HILINK_ERR	= 9,
-	HCLGE_CMD_QUEUE_ILLEGAL	= 10,
-	HCLGE_CMD_INVALID	= 11,
-};
-
-enum hclge_cmd_status {
-	HCLGE_STATUS_SUCCESS	= 0,
-	HCLGE_ERR_CSQ_FULL	= -1,
-	HCLGE_ERR_CSQ_TIMEOUT	= -2,
-	HCLGE_ERR_CSQ_ERROR	= -3,
-};
-
 struct hclge_misc_vector {
 	u8 __iomem *addr;
 	int vector_irq;
 	char name[HNAE3_INT_NAME_LEN];
 };
 
-struct hclge_cmq {
-	struct hclge_cmq_ring csq;
-	struct hclge_cmq_ring crq;
-	u16 tx_timeout;
-	enum hclge_cmd_status last_status;
-};
-
 #define HCLGE_CMD_FLAG_IN	BIT(0)
 #define HCLGE_CMD_FLAG_OUT	BIT(1)
 #define HCLGE_CMD_FLAG_NEXT	BIT(2)
@@ -1188,7 +1136,9 @@
 	__le16 max_frm_size;
 	__le16 max_qset_num;
 	__le16 max_int_gl;
-	u8 rsv1[18];
+	u8 rsv0[2];
+	__le16 umv_size;
+	u8 rsv1[14];
 };
 
 /* mac speed type defined in firmware command */
@@ -1241,25 +1191,6 @@
 };
 
 int hclge_cmd_init(struct hclge_dev *hdev);
-static inline void hclge_write_reg(void __iomem *base, u32 reg, u32 value)
-{
-	writel(value, base + reg);
-}
-
-#define hclge_write_dev(a, reg, value) \
-	hclge_write_reg((a)->io_base, reg, value)
-#define hclge_read_dev(a, reg) \
-	hclge_read_reg((a)->io_base, reg)
-
-static inline u32 hclge_read_reg(u8 __iomem *base, u32 reg)
-{
-	u8 __iomem *reg_addr = READ_ONCE(base);
-
-	return readl(reg_addr + reg);
-}
-
-#define HCLGE_SEND_SYNC(flag) \
-	((flag) & HCLGE_CMD_FLAG_NO_INTR)
 
 struct hclge_hw;
 int hclge_cmd_send(struct hclge_hw *hw, struct hclge_desc *desc, int num);
@@ -1267,10 +1198,10 @@
 				enum hclge_opcode_type opcode, bool is_read);
 void hclge_cmd_reuse_desc(struct hclge_desc *desc, bool is_read);
 
-enum hclge_cmd_status hclge_cmd_mdio_write(struct hclge_hw *hw,
-					   struct hclge_desc *desc);
-enum hclge_cmd_status hclge_cmd_mdio_read(struct hclge_hw *hw,
-					  struct hclge_desc *desc);
+enum hclge_comm_cmd_status hclge_cmd_mdio_write(struct hclge_hw *hw,
+						struct hclge_desc *desc);
+enum hclge_comm_cmd_status hclge_cmd_mdio_read(struct hclge_hw *hw,
+					       struct hclge_desc *desc);
 
 void hclge_cmd_uninit(struct hclge_dev *hdev);
 int hclge_cmd_queue_init(struct hclge_dev *hdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_dcb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_dcb.c
@@ -52,7 +52,10 @@
 
 	for (i = 0; i < HNAE3_MAX_TC; i++) {
 		ets->prio_tc[i] = hdev->tm_info.prio_tc[i];
-		ets->tc_tx_bw[i] = hdev->tm_info.pg_info[0].tc_dwrr[i];
+		if (i < hdev->tm_info.num_tc)
+			ets->tc_tx_bw[i] = hdev->tm_info.pg_info[0].tc_dwrr[i];
+		else
+			ets->tc_tx_bw[i] = 0;
 
 		if (hdev->tm_info.tc_info[i].tc_sch_mode ==
 		    HCLGE_SCH_MODE_SP)
@@ -123,13 +126,14 @@
 }
 
 static int hclge_ets_sch_mode_validate(struct hclge_dev *hdev,
-				       struct ieee_ets *ets, bool *changed)
+				       struct ieee_ets *ets, bool *changed,
+				       u8 tc_num)
 {
 	bool has_ets_tc = false;
 	u32 total_ets_bw = 0;
 	u8 i;
 
-	for (i = 0; i < hdev->tc_max; i++) {
+	for (i = 0; i < HNAE3_MAX_TC; i++) {
 		switch (ets->tc_tsa[i]) {
 		case IEEE_8021QAZ_TSA_STRICT:
 			if (hdev->tm_info.tc_info[i].tc_sch_mode !=
@@ -137,6 +141,13 @@
 				*changed = true;
 			break;
 		case IEEE_8021QAZ_TSA_ETS:
+			if (i >= tc_num) {
+				dev_err(&hdev->pdev->dev,
+					"tc%u is disabled, cannot set ets bw\n",
+					i);
+				return -EINVAL;
+			}
+
 			/* The hardware will switch to sp mode if bandwidth is
 			 * 0, so limit ets bandwidth must be greater than 0.
 			 */
@@ -176,7 +187,7 @@
 	if (ret)
 		return ret;
 
-	ret = hclge_ets_sch_mode_validate(hdev, ets, changed);
+	ret = hclge_ets_sch_mode_validate(hdev, ets, changed, tc_num);
 	if (ret)
 		return ret;
 
@@ -240,7 +251,7 @@
 	int ret;
 
 	if (!(hdev->dcbx_cap & DCB_CAP_DCBX_VER_IEEE) ||
-	    hdev->flag & HCLGE_FLAG_MQPRIO_ENABLE)
+	    h->kinfo.tc_info.mqprio_active)
 		return -EINVAL;
 
 	ret = hclge_ets_validate(hdev, ets, &num_tc, &map_changed);
@@ -256,10 +267,7 @@
 	}
 
 	hclge_tm_schd_info_update(hdev, num_tc);
-	if (num_tc > 1)
-		hdev->flag |= HCLGE_FLAG_DCB_ENABLE;
-	else
-		hdev->flag &= ~HCLGE_FLAG_DCB_ENABLE;
+	h->kinfo.tc_info.dcb_ets_active = num_tc > 1;
 
 	ret = hclge_ieee_ets_to_tm_info(hdev, ets);
 	if (ret)
@@ -286,28 +294,24 @@
 
 static int hclge_ieee_getpfc(struct hnae3_handle *h, struct ieee_pfc *pfc)
 {
-	u64 requests[HNAE3_MAX_TC], indications[HNAE3_MAX_TC];
 	struct hclge_vport *vport = hclge_get_vport(h);
 	struct hclge_dev *hdev = vport->back;
 	int ret;
-	u8 i;
 
 	memset(pfc, 0, sizeof(*pfc));
 	pfc->pfc_cap = hdev->pfc_max;
 	pfc->pfc_en = hdev->tm_info.pfc_en;
 
-	ret = hclge_pfc_tx_stats_get(hdev, requests);
-	if (ret)
+	ret = hclge_mac_update_stats(hdev);
+	if (ret) {
+		dev_err(&hdev->pdev->dev,
+			"failed to update MAC stats, ret = %d.\n", ret);
 		return ret;
+	}
 
-	ret = hclge_pfc_rx_stats_get(hdev, indications);
-	if (ret)
-		return ret;
+	hclge_pfc_tx_stats_get(hdev, pfc->requests);
+	hclge_pfc_rx_stats_get(hdev, pfc->indications);
 
-	for (i = 0; i < HCLGE_MAX_TC_NUM; i++) {
-		pfc->requests[i] = requests[i];
-		pfc->indications[i] = indications[i];
-	}
 	return 0;
 }
 
@@ -369,7 +373,7 @@
 	struct hclge_vport *vport = hclge_get_vport(h);
 	struct hclge_dev *hdev = vport->back;
 
-	if (hdev->flag & HCLGE_FLAG_MQPRIO_ENABLE)
+	if (h->kinfo.tc_info.mqprio_active)
 		return 0;
 
 	return hdev->dcbx_cap;
@@ -493,7 +497,8 @@
 	if (!test_bit(HCLGE_STATE_NIC_REGISTERED, &hdev->state))
 		return -EBUSY;
 
-	if (hdev->flag & HCLGE_FLAG_DCB_ENABLE)
+	kinfo = &vport->nic.kinfo;
+	if (kinfo->tc_info.dcb_ets_active)
 		return -EINVAL;
 
 	ret = hclge_mqprio_qopt_check(hdev, mqprio_qopt);
@@ -507,7 +512,6 @@
 	if (ret)
 		return ret;
 
-	kinfo = &vport->nic.kinfo;
 	memcpy(&old_tc_info, &kinfo->tc_info, sizeof(old_tc_info));
 	hclge_sync_mqprio_qopt(&kinfo->tc_info, mqprio_qopt);
 	kinfo->tc_info.mqprio_active = tc > 0;
@@ -516,13 +520,6 @@
 	if (ret)
 		goto err_out;
 
-	hdev->flag &= ~HCLGE_FLAG_DCB_ENABLE;
-
-	if (tc > 1)
-		hdev->flag |= HCLGE_FLAG_MQPRIO_ENABLE;
-	else
-		hdev->flag &= ~HCLGE_FLAG_MQPRIO_ENABLE;
-
 	return hclge_notify_init_up(hdev);
 
 err_out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_debugfs.c
@@ -677,8 +677,7 @@
 	for (i = 0; i < HNAE3_MAX_TC; i++) {
 		sch_mode_str = ets_weight->tc_weight[i] ? "dwrr" : "sp";
 		pos += scnprintf(buf + pos, len - pos, "%u     %4s    %3u\n",
-				 i, sch_mode_str,
-				 hdev->tm_info.pg_info[0].tc_dwrr[i]);
+				 i, sch_mode_str, ets_weight->tc_weight[i]);
 	}
 
 	return 0;
@@ -1451,7 +1450,7 @@
 	struct hclge_desc desc[3];
 	int pos = 0;
 	int ret, i;
-	u32 *req;
+	__le32 *req;
 
 	hclge_cmd_setup_basic_desc(&desc[0], HCLGE_OPC_FD_TCAM_OP, true);
 	desc[0].flag |= cpu_to_le16(HCLGE_CMD_FLAG_NEXT);
@@ -1476,22 +1475,22 @@
 			 tcam_msg.loc);
 
 	/* tcam_data0 ~ tcam_data1 */
-	req = (u32 *)req1->tcam_data;
+	req = (__le32 *)req1->tcam_data;
 	for (i = 0; i < 2; i++)
 		pos += scnprintf(tcam_buf + pos, HCLGE_DBG_TCAM_BUF_SIZE - pos,
-				 "%08x\n", *req++);
+				 "%08x\n", le32_to_cpu(*req++));
 
 	/* tcam_data2 ~ tcam_data7 */
-	req = (u32 *)req2->tcam_data;
+	req = (__le32 *)req2->tcam_data;
 	for (i = 0; i < 6; i++)
 		pos += scnprintf(tcam_buf + pos, HCLGE_DBG_TCAM_BUF_SIZE - pos,
-				 "%08x\n", *req++);
+				 "%08x\n", le32_to_cpu(*req++));
 
 	/* tcam_data8 ~ tcam_data12 */
-	req = (u32 *)req3->tcam_data;
+	req = (__le32 *)req3->tcam_data;
 	for (i = 0; i < 5; i++)
 		pos += scnprintf(tcam_buf + pos, HCLGE_DBG_TCAM_BUF_SIZE - pos,
-				 "%08x\n", *req++);
+				 "%08x\n", le32_to_cpu(*req++));
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -24,10 +24,9 @@
 #include "hclge_err.h"
 #include "hnae3.h"
 #include "hclge_devlink.h"
+#include "hclge_comm_cmd.h"
 
 #define HCLGE_NAME			"hclge"
-#define HCLGE_STATS_READ(p, offset) (*(u64 *)((u8 *)(p) + (offset)))
-#define HCLGE_MAC_STATS_FIELD_OFF(f) (offsetof(struct hclge_mac_stats, f))
 
 #define HCLGE_BUF_SIZE_UNIT	256U
 #define HCLGE_BUF_MUL_BY	2
@@ -72,6 +71,9 @@
 static void hclge_restore_hw_table(struct hclge_dev *hdev);
 static void hclge_sync_promisc_mode(struct hclge_dev *hdev);
 static void hclge_sync_fd_table(struct hclge_dev *hdev);
+static int hclge_mac_link_status_wait(struct hclge_dev *hdev, int link_ret,
+				      int wait_cnt);
+static int hclge_update_port_info(struct hclge_dev *hdev);
 
 static struct hnae3_ae_algo ae_algo;
 
@@ -548,7 +550,7 @@
 	return 0;
 }
 
-static int hclge_mac_update_stats(struct hclge_dev *hdev)
+int hclge_mac_update_stats(struct hclge_dev *hdev)
 {
 	u32 desc_num;
 	int ret;
@@ -1342,8 +1344,6 @@
 	cfg->umv_space = hnae3_get_field(__le32_to_cpu(req->param[1]),
 					 HCLGE_CFG_UMV_TBL_SPACE_M,
 					 HCLGE_CFG_UMV_TBL_SPACE_S);
-	if (!cfg->umv_space)
-		cfg->umv_space = HCLGE_DEFAULT_UMV_SPACE_PER_PF;
 
 	cfg->pf_rss_size_max = hnae3_get_field(__le32_to_cpu(req->param[2]),
 					       HCLGE_CFG_PF_RSS_SIZE_M,
@@ -1419,6 +1419,7 @@
 	ae_dev->dev_specs.max_int_gl = HCLGE_DEF_MAX_INT_GL;
 	ae_dev->dev_specs.max_frm_size = HCLGE_MAC_MAX_FRAME;
 	ae_dev->dev_specs.max_qset_num = HCLGE_MAX_QSET_NUM;
+	ae_dev->dev_specs.umv_size = HCLGE_DEFAULT_UMV_SPACE_PER_PF;
 }
 
 static void hclge_parse_dev_specs(struct hclge_dev *hdev,
@@ -1440,6 +1441,7 @@
 	ae_dev->dev_specs.max_qset_num = le16_to_cpu(req1->max_qset_num);
 	ae_dev->dev_specs.max_int_gl = le16_to_cpu(req1->max_int_gl);
 	ae_dev->dev_specs.max_frm_size = le16_to_cpu(req1->max_frm_size);
+	ae_dev->dev_specs.umv_size = le16_to_cpu(req1->umv_size);
 }
 
 static void hclge_check_dev_specs(struct hclge_dev *hdev)
@@ -1460,6 +1462,8 @@
 		dev_specs->max_int_gl = HCLGE_DEF_MAX_INT_GL;
 	if (!dev_specs->max_frm_size)
 		dev_specs->max_frm_size = HCLGE_MAC_MAX_FRAME;
+	if (!dev_specs->umv_size)
+		dev_specs->umv_size = HCLGE_DEFAULT_UMV_SPACE_PER_PF;
 }
 
 static int hclge_query_dev_specs(struct hclge_dev *hdev)
@@ -1549,7 +1553,10 @@
 	hdev->tm_info.num_pg = 1;
 	hdev->tc_max = cfg.tc_num;
 	hdev->tm_info.hw_pfc_map = 0;
-	hdev->wanted_umv_size = cfg.umv_space;
+	if (cfg.umv_space)
+		hdev->wanted_umv_size = cfg.umv_space;
+	else
+		hdev->wanted_umv_size = hdev->ae_dev->dev_specs.umv_size;
 	hdev->tx_spare_buf_size = cfg.tx_spare_buf_size;
 	hdev->gro_en = true;
 	if (cfg.vlan_fliter_cap == HCLGE_VLAN_FLTR_CAN_MDF)
@@ -1566,6 +1573,9 @@
 			cfg.default_speed, ret);
 		return ret;
 	}
+	hdev->hw.mac.req_speed = hdev->hw.mac.speed;
+	hdev->hw.mac.req_autoneg = AUTONEG_ENABLE;
+	hdev->hw.mac.req_duplex = DUPLEX_FULL;
 
 	hclge_parse_link_mode(hdev, cfg.speed_ability);
 
@@ -1668,11 +1678,11 @@
 		 * HCLGE_TQP_MAX_SIZE_DEV_V2
 		 */
 		if (i < HCLGE_TQP_MAX_SIZE_DEV_V2)
-			tqp->q.io_base = hdev->hw.io_base +
+			tqp->q.io_base = hdev->hw.hw.io_base +
 					 HCLGE_TQP_REG_OFFSET +
 					 i * HCLGE_TQP_REG_SIZE;
 		else
-			tqp->q.io_base = hdev->hw.io_base +
+			tqp->q.io_base = hdev->hw.hw.io_base +
 					 HCLGE_TQP_REG_OFFSET +
 					 HCLGE_TQP_EXT_REG_OFFSET +
 					 (i - HCLGE_TQP_MAX_SIZE_DEV_V2) *
@@ -1815,8 +1825,9 @@
 
 	nic->pdev = hdev->pdev;
 	nic->ae_algo = &ae_algo;
-	nic->numa_node_mask = hdev->numa_node_mask;
-	nic->kinfo.io_base = hdev->hw.io_base;
+	bitmap_copy(nic->numa_node_mask.bits, hdev->numa_node_mask.bits,
+		    MAX_NUMNODES);
+	nic->kinfo.io_base = hdev->hw.hw.io_base;
 
 	ret = hclge_knic_setup(vport, num_tqps,
 			       hdev->num_tx_desc, hdev->num_rx_desc);
@@ -1865,6 +1876,7 @@
 		vport->vf_info.link_state = IFLA_VF_LINK_STATE_AUTO;
 		vport->mps = HCLGE_MAC_DEFAULT_FRAME;
 		vport->port_base_vlan_cfg.state = HNAE3_PORT_BASE_VLAN_DISABLE;
+		vport->port_base_vlan_cfg.tbl_sta = true;
 		vport->rxvlan_cfg.rx_vlan_offload_en = true;
 		vport->req_vlan_fltr_en = true;
 		INIT_LIST_HEAD(&vport->vlan_list);
@@ -2498,15 +2510,16 @@
 	if (hdev->num_msi < hdev->num_nic_msi + hdev->num_roce_msi)
 		return -EINVAL;
 
-	roce->rinfo.base_vector = hdev->roce_base_vector;
+	roce->rinfo.base_vector = hdev->num_nic_msi;
 
 	roce->rinfo.netdev = nic->kinfo.netdev;
-	roce->rinfo.roce_io_base = hdev->hw.io_base;
-	roce->rinfo.roce_mem_base = hdev->hw.mem_base;
+	roce->rinfo.roce_io_base = hdev->hw.hw.io_base;
+	roce->rinfo.roce_mem_base = hdev->hw.hw.mem_base;
 
 	roce->pdev = nic->pdev;
 	roce->ae_algo = nic->ae_algo;
-	roce->numa_node_mask = nic->numa_node_mask;
+	bitmap_copy(roce->numa_node_mask.bits, nic->numa_node_mask.bits,
+		    MAX_NUMNODES);
 
 	return 0;
 }
@@ -2534,10 +2547,6 @@
 	hdev->num_msi = vectors;
 	hdev->num_msi_left = vectors;
 
-	hdev->base_msi_vector = pdev->irq;
-	hdev->roce_base_vector = hdev->base_msi_vector +
-				hdev->num_nic_msi;
-
 	hdev->vector_status = devm_kcalloc(&pdev->dev, hdev->num_msi,
 					   sizeof(u16), GFP_KERNEL);
 	if (!hdev->vector_status) {
@@ -2805,7 +2814,10 @@
 	int ret;
 
 	hdev->support_sfp_query = true;
-	hdev->hw.mac.duplex = HCLGE_MAC_FULL;
+
+	if (!test_bit(HCLGE_STATE_RST_HANDLING, &hdev->state))
+		hdev->hw.mac.duplex = HCLGE_MAC_FULL;
+
 	ret = hclge_cfg_mac_speed_dup_hw(hdev, hdev->hw.mac.speed,
 					 hdev->hw.mac.duplex);
 	if (ret)
@@ -2846,16 +2858,20 @@
 static void hclge_mbx_task_schedule(struct hclge_dev *hdev)
 {
 	if (!test_bit(HCLGE_STATE_REMOVING, &hdev->state) &&
-	    !test_and_set_bit(HCLGE_STATE_MBX_SERVICE_SCHED, &hdev->state))
+	    !test_and_set_bit(HCLGE_STATE_MBX_SERVICE_SCHED, &hdev->state)) {
+		hdev->last_mbx_scheduled = jiffies;
 		mod_delayed_work(hclge_wq, &hdev->service_task, 0);
+	}
 }
 
 static void hclge_reset_task_schedule(struct hclge_dev *hdev)
 {
 	if (!test_bit(HCLGE_STATE_REMOVING, &hdev->state) &&
 	    test_bit(HCLGE_STATE_SERVICE_INITED, &hdev->state) &&
-	    !test_and_set_bit(HCLGE_STATE_RST_SERVICE_SCHED, &hdev->state))
+	    !test_and_set_bit(HCLGE_STATE_RST_SERVICE_SCHED, &hdev->state)) {
+		hdev->last_rst_scheduled = jiffies;
 		mod_delayed_work(hclge_wq, &hdev->service_task, 0);
+	}
 }
 
 static void hclge_errhand_task_schedule(struct hclge_dev *hdev)
@@ -2932,9 +2948,7 @@
 
 static void hclge_update_link_status(struct hclge_dev *hdev)
 {
-	struct hnae3_handle *rhandle = &hdev->vport[0].roce;
 	struct hnae3_handle *handle = &hdev->vport[0].nic;
-	struct hnae3_client *rclient = hdev->roce_client;
 	struct hnae3_client *client = hdev->nic_client;
 	int state;
 	int ret;
@@ -2953,10 +2967,20 @@
 
 	if (state != hdev->hw.mac.link) {
 		hdev->hw.mac.link = state;
+		if (state == HCLGE_LINK_STATUS_UP)
+			hclge_update_port_info(hdev);
+
 		client->ops->link_status_change(handle, state);
 		hclge_config_mac_tnl_int(hdev, state);
-		if (rclient && rclient->ops->link_status_change)
-			rclient->ops->link_status_change(rhandle, state);
+
+		if (test_bit(HCLGE_STATE_ROCE_REGISTERED, &hdev->state)) {
+			struct hnae3_handle *rhandle = &hdev->vport[0].roce;
+			struct hnae3_client *rclient = hdev->roce_client;
+
+			if (rclient && rclient->ops->link_status_change)
+				rclient->ops->link_status_change(rhandle,
+								 state);
+		}
 
 		hclge_push_link_status(hdev);
 	}
@@ -3154,9 +3178,9 @@
 		return ret;
 	}
 
-	hdev->hw.mac.autoneg = cmd->base.autoneg;
-	hdev->hw.mac.speed = cmd->base.speed;
-	hdev->hw.mac.duplex = cmd->base.duplex;
+	hdev->hw.mac.req_autoneg = cmd->base.autoneg;
+	hdev->hw.mac.req_speed = cmd->base.speed;
+	hdev->hw.mac.req_duplex = cmd->base.duplex;
 	linkmode_copy(hdev->hw.mac.advertising, cmd->link_modes.advertising);
 
 	return 0;
@@ -3177,6 +3201,7 @@
 	hdev->hw.mac.autoneg = cmd.base.autoneg;
 	hdev->hw.mac.speed = cmd.base.speed;
 	hdev->hw.mac.duplex = cmd.base.duplex;
+	linkmode_copy(hdev->hw.mac.advertising, cmd.link_modes.advertising);
 
 	return 0;
 }
@@ -3188,9 +3213,9 @@
 	if (!hnae3_dev_phy_imp_supported(hdev))
 		return 0;
 
-	cmd.base.autoneg = hdev->hw.mac.autoneg;
-	cmd.base.speed = hdev->hw.mac.speed;
-	cmd.base.duplex = hdev->hw.mac.duplex;
+	cmd.base.autoneg = hdev->hw.mac.req_autoneg;
+	cmd.base.speed = hdev->hw.mac.req_speed;
+	cmd.base.duplex = hdev->hw.mac.req_duplex;
 	linkmode_copy(cmd.link_modes.advertising, hdev->hw.mac.advertising);
 
 	return hclge_set_phy_link_ksettings(&hdev->vport->nic, &cmd);
@@ -3199,7 +3224,7 @@
 static int hclge_update_port_info(struct hclge_dev *hdev)
 {
 	struct hclge_mac *mac = &hdev->hw.mac;
-	int speed = HCLGE_MAC_SPEED_UNKNOWN;
+	int speed;
 	int ret;
 
 	/* get the port info from SFP cmd if not copper port */
@@ -3210,10 +3235,13 @@
 	if (!hdev->support_sfp_query)
 		return 0;
 
-	if (hdev->ae_dev->dev_version >= HNAE3_DEVICE_VERSION_V2)
+	if (hdev->ae_dev->dev_version >= HNAE3_DEVICE_VERSION_V2) {
+		speed = mac->speed;
 		ret = hclge_get_sfp_info(hdev, mac);
-	else
+	} else {
+		speed = HCLGE_MAC_SPEED_UNKNOWN;
 		ret = hclge_get_sfp_speed(hdev, &speed);
+	}
 
 	if (ret == -EOPNOTSUPP) {
 		hdev->support_sfp_query = false;
@@ -3225,6 +3253,8 @@
 	if (hdev->ae_dev->dev_version >= HNAE3_DEVICE_VERSION_V2) {
 		if (mac->speed_type == QUERY_ACTIVE_SPEED) {
 			hclge_update_port_capability(hdev, mac);
+			if (mac->speed != speed)
+				(void)hclge_tm_port_shaper_cfg(hdev);
 			return 0;
 		}
 		return hclge_cfg_mac_speed_dup(hdev, mac->speed,
@@ -3307,6 +3337,12 @@
 	link_state_old = vport->vf_info.link_state;
 	vport->vf_info.link_state = link_state;
 
+	/* return success directly if the VF is unalive, VF will
+	 * query link state itself when it starts work.
+	 */
+	if (!test_bit(HCLGE_VPORT_STATE_ALIVE, &vport->state))
+		return 0;
+
 	ret = hclge_push_vf_link_status(vport);
 	if (ret) {
 		vport->vf_info.link_state = link_state_old;
@@ -3338,7 +3374,7 @@
 	if (BIT(HCLGE_VECTOR0_IMPRESET_INT_B) & msix_src_reg) {
 		dev_info(&hdev->pdev->dev, "IMP reset interrupt\n");
 		set_bit(HNAE3_IMP_RESET, &hdev->reset_pending);
-		set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+		set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 		*clearval = BIT(HCLGE_VECTOR0_IMPRESET_INT_B);
 		hdev->rst_stats.imp_rst_cnt++;
 		return HCLGE_VECTOR0_EVENT_RST;
@@ -3346,7 +3382,7 @@
 
 	if (BIT(HCLGE_VECTOR0_GLOBALRESET_INT_B) & msix_src_reg) {
 		dev_info(&hdev->pdev->dev, "global reset interrupt\n");
-		set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+		set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 		set_bit(HNAE3_GLOBAL_RESET, &hdev->reset_pending);
 		*clearval = BIT(HCLGE_VECTOR0_GLOBALRESET_INT_B);
 		hdev->rst_stats.global_rst_cnt++;
@@ -3382,9 +3418,14 @@
 static void hclge_clear_event_cause(struct hclge_dev *hdev, u32 event_type,
 				    u32 regclr)
 {
+#define HCLGE_IMP_RESET_DELAY		5
+
 	switch (event_type) {
 	case HCLGE_VECTOR0_EVENT_PTP:
 	case HCLGE_VECTOR0_EVENT_RST:
+		if (regclr == BIT(HCLGE_VECTOR0_IMPRESET_INT_B))
+			mdelay(HCLGE_IMP_RESET_DELAY);
+
 		hclge_write_dev(&hdev->hw, HCLGE_MISC_RESET_STS_REG, regclr);
 		break;
 	case HCLGE_VECTOR0_EVENT_MBX:
@@ -3480,7 +3521,7 @@
 
 	vector->vector_irq = pci_irq_vector(hdev->pdev, 0);
 
-	vector->addr = hdev->hw.io_base + HCLGE_MISC_VECTOR_REG_BASE;
+	vector->addr = hdev->hw.hw.io_base + HCLGE_MISC_VECTOR_REG_BASE;
 	hdev->vector_status[0] = 0;
 
 	hdev->num_msi_left -= 1;
@@ -3664,10 +3705,17 @@
 static void hclge_mailbox_service_task(struct hclge_dev *hdev)
 {
 	if (!test_and_clear_bit(HCLGE_STATE_MBX_SERVICE_SCHED, &hdev->state) ||
-	    test_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state) ||
+	    test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state) ||
 	    test_and_set_bit(HCLGE_STATE_MBX_HANDLING, &hdev->state))
 		return;
 
+	if (time_is_before_jiffies(hdev->last_mbx_scheduled +
+				   HCLGE_MBX_SCHED_TIMEOUT))
+		dev_warn(&hdev->pdev->dev,
+			 "mbx service task is scheduled after %ums on cpu%u!\n",
+			 jiffies_to_msecs(jiffies - hdev->last_mbx_scheduled),
+			 smp_processor_id());
+
 	hclge_mbx_handler(hdev);
 
 	clear_bit(HCLGE_STATE_MBX_HANDLING, &hdev->state);
@@ -3904,7 +3952,7 @@
 		 * any mailbox handling or command to firmware is only valid
 		 * after hclge_cmd_init is called.
 		 */
-		set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+		set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 		hdev->rst_stats.pf_rst_cnt++;
 		break;
 	case HNAE3_FLR_RESET:
@@ -4317,6 +4365,13 @@
 	if (!test_and_clear_bit(HCLGE_STATE_RST_SERVICE_SCHED, &hdev->state))
 		return;
 
+	if (time_is_before_jiffies(hdev->last_rst_scheduled +
+				   HCLGE_RESET_SCHED_TIMEOUT))
+		dev_warn(&hdev->pdev->dev,
+			 "reset service task is scheduled after %ums on cpu%u!\n",
+			 jiffies_to_msecs(jiffies - hdev->last_rst_scheduled),
+			 smp_processor_id());
+
 	down(&hdev->reset_sem);
 	set_bit(HCLGE_STATE_RST_HANDLING, &hdev->state);
 
@@ -4451,11 +4506,11 @@
 
 	/* need an extend offset to config vector >= 64 */
 	if (idx - 1 < HCLGE_PF_MAX_VECTOR_NUM_DEV_V2)
-		vector_info->io_addr = hdev->hw.io_base +
+		vector_info->io_addr = hdev->hw.hw.io_base +
 				HCLGE_VECTOR_REG_BASE +
 				(idx - 1) * HCLGE_VECTOR_REG_OFFSET;
 	else
-		vector_info->io_addr = hdev->hw.io_base +
+		vector_info->io_addr = hdev->hw.hw.io_base +
 				HCLGE_VECTOR_EXT_REG_BASE +
 				(idx - 1) / HCLGE_PF_MAX_VECTOR_NUM_DEV_V2 *
 				HCLGE_VECTOR_REG_OFFSET_H +
@@ -5093,7 +5148,7 @@
 	struct hclge_desc desc;
 	struct hclge_ctrl_vector_chain_cmd *req =
 		(struct hclge_ctrl_vector_chain_cmd *)desc.data;
-	enum hclge_cmd_status status;
+	enum hclge_comm_cmd_status status;
 	enum hclge_opcode_type op;
 	u16 tqp_type_and_id;
 	int i;
@@ -7537,6 +7592,12 @@
 	ret = hclge_fd_tcam_config(hdev, HCLGE_FD_STAGE_1, true, rule->location,
 				   NULL, false);
 	if (ret) {
+		/* if tcam config fail, set rule state to TO_DEL,
+		 * so the rule will be deleted when periodic
+		 * task being scheduled.
+		 */
+		hclge_update_fd_list(hdev, HCLGE_FD_TO_DEL, rule->location, NULL);
+		set_bit(HCLGE_STATE_FD_TBL_CHANGED, &hdev->state);
 		spin_unlock_bh(&hdev->fd_rule_lock);
 		return ret;
 	}
@@ -7613,7 +7674,7 @@
 	struct hclge_vport *vport = hclge_get_vport(handle);
 	struct hclge_dev *hdev = vport->back;
 
-	return test_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+	return test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 }
 
 static bool hclge_ae_dev_resetting(struct hnae3_handle *handle)
@@ -7649,6 +7710,8 @@
 
 static void hclge_cfg_mac_mode(struct hclge_dev *hdev, bool enable)
 {
+#define HCLGE_LINK_STATUS_WAIT_CNT  3
+
 	struct hclge_desc desc;
 	struct hclge_config_mac_mode_cmd *req =
 		(struct hclge_config_mac_mode_cmd *)desc.data;
@@ -7673,9 +7736,15 @@
 	req->txrx_pad_fcs_loop_en = cpu_to_le32(loop_en);
 
 	ret = hclge_cmd_send(&hdev->hw, &desc, 1);
-	if (ret)
+	if (ret) {
 		dev_err(&hdev->pdev->dev,
 			"mac enable fail, ret =%d.\n", ret);
+		return;
+	}
+
+	if (!enable)
+		hclge_mac_link_status_wait(hdev, HCLGE_LINK_STATUS_DOWN,
+					   HCLGE_LINK_STATUS_WAIT_CNT);
 }
 
 static int hclge_config_switch_param(struct hclge_dev *hdev, int vfid,
@@ -7738,10 +7807,9 @@
 	} while (++i < HCLGE_PHY_LINK_STATUS_NUM);
 }
 
-static int hclge_mac_link_status_wait(struct hclge_dev *hdev, int link_ret)
+static int hclge_mac_link_status_wait(struct hclge_dev *hdev, int link_ret,
+				      int wait_cnt)
 {
-#define HCLGE_MAC_LINK_STATUS_NUM  100
-
 	int link_status;
 	int i = 0;
 	int ret;
@@ -7754,13 +7822,15 @@
 			return 0;
 
 		msleep(HCLGE_LINK_STATUS_MS);
-	} while (++i < HCLGE_MAC_LINK_STATUS_NUM);
+	} while (++i < wait_cnt);
 	return -EBUSY;
 }
 
 static int hclge_mac_phy_link_status_wait(struct hclge_dev *hdev, bool en,
 					  bool is_phy)
 {
+#define HCLGE_MAC_LINK_STATUS_NUM  100
+
 	int link_ret;
 
 	link_ret = en ? HCLGE_LINK_STATUS_UP : HCLGE_LINK_STATUS_DOWN;
@@ -7768,7 +7838,8 @@
 	if (is_phy)
 		hclge_phy_link_status_wait(hdev, link_ret);
 
-	return hclge_mac_link_status_wait(hdev, link_ret);
+	return hclge_mac_link_status_wait(hdev, link_ret,
+					  HCLGE_MAC_LINK_STATUS_NUM);
 }
 
 static int hclge_set_app_loopback(struct hclge_dev *hdev, bool en)
@@ -8090,8 +8161,7 @@
 		/* Set the DOWN flag here to disable link updating */
 		set_bit(HCLGE_STATE_DOWN, &hdev->state);
 
-		/* flush memory to make sure DOWN is seen by service task */
-		smp_mb__before_atomic();
+		smp_mb__after_atomic(); /* flush memory to make sure DOWN is seen by service task */
 		hclge_flush_link_update(hdev);
 	}
 }
@@ -8127,12 +8197,15 @@
 	/* If it is not PF reset or FLR, the firmware will disable the MAC,
 	 * so it only need to stop phy here.
 	 */
-	if (test_bit(HCLGE_STATE_RST_HANDLING, &hdev->state) &&
-	    hdev->reset_type != HNAE3_FUNC_RESET &&
-	    hdev->reset_type != HNAE3_FLR_RESET) {
-		hclge_mac_stop_phy(hdev);
-		hclge_update_link_status(hdev);
-		return;
+	if (test_bit(HCLGE_STATE_RST_HANDLING, &hdev->state)) {
+		hclge_pfc_pause_en_cfg(hdev, HCLGE_PFC_TX_RX_DISABLE,
+				       HCLGE_PFC_DISABLE);
+		if (hdev->reset_type != HNAE3_FUNC_RESET &&
+		    hdev->reset_type != HNAE3_FLR_RESET) {
+			hclge_mac_stop_phy(hdev);
+			hclge_update_link_status(hdev);
+			return;
+		}
 	}
 
 	hclge_reset_tqp(handle);
@@ -8575,6 +8648,7 @@
 			  enum HCLGE_MAC_ADDR_TYPE mac_type,
 			  const unsigned char *addr)
 {
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 	struct hclge_mac_node *mac_node;
 	struct list_head *list;
@@ -8599,9 +8673,10 @@
 	/* if this address is never added, unnecessary to delete */
 	if (state == HCLGE_MAC_TO_DEL) {
 		spin_unlock_bh(&vport->mac_list_lock);
+		hnae3_format_mac_addr(format_mac_addr, addr);
 		dev_err(&hdev->pdev->dev,
-			"failed to delete address %pM from mac list\n",
-			addr);
+			"failed to delete address %s from mac list\n",
+			format_mac_addr);
 		return -ENOENT;
 	}
 
@@ -8634,6 +8709,7 @@
 int hclge_add_uc_addr_common(struct hclge_vport *vport,
 			     const unsigned char *addr)
 {
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 	struct hclge_mac_vlan_tbl_entry_cmd req;
 	struct hclge_desc desc;
@@ -8644,9 +8720,10 @@
 	if (is_zero_ether_addr(addr) ||
 	    is_broadcast_ether_addr(addr) ||
 	    is_multicast_ether_addr(addr)) {
+		hnae3_format_mac_addr(format_mac_addr, addr);
 		dev_err(&hdev->pdev->dev,
-			"Set_uc mac err! invalid mac:%pM. is_zero:%d,is_br=%d,is_mul=%d\n",
-			 addr, is_zero_ether_addr(addr),
+			"Set_uc mac err! invalid mac:%s. is_zero:%d,is_br=%d,is_mul=%d\n",
+			 format_mac_addr, is_zero_ether_addr(addr),
 			 is_broadcast_ether_addr(addr),
 			 is_multicast_ether_addr(addr));
 		return -EINVAL;
@@ -8703,6 +8780,7 @@
 int hclge_rm_uc_addr_common(struct hclge_vport *vport,
 			    const unsigned char *addr)
 {
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 	struct hclge_mac_vlan_tbl_entry_cmd req;
 	int ret;
@@ -8711,8 +8789,9 @@
 	if (is_zero_ether_addr(addr) ||
 	    is_broadcast_ether_addr(addr) ||
 	    is_multicast_ether_addr(addr)) {
-		dev_dbg(&hdev->pdev->dev, "Remove mac err! invalid mac:%pM.\n",
-			addr);
+		hnae3_format_mac_addr(format_mac_addr, addr);
+		dev_dbg(&hdev->pdev->dev, "Remove mac err! invalid mac:%s.\n",
+			format_mac_addr);
 		return -EINVAL;
 	}
 
@@ -8720,12 +8799,11 @@
 	hnae3_set_bit(req.entry_type, HCLGE_MAC_VLAN_BIT0_EN_B, 0);
 	hclge_prepare_mac_addr(&req, addr, false);
 	ret = hclge_remove_mac_vlan_tbl(vport, &req);
-	if (!ret) {
+	if (!ret || ret == -ENOENT) {
 		mutex_lock(&hdev->vport_lock);
 		hclge_update_umv_space(vport, true);
 		mutex_unlock(&hdev->vport_lock);
-	} else if (ret == -ENOENT) {
-		ret = 0;
+		return 0;
 	}
 
 	return ret;
@@ -8743,6 +8821,7 @@
 int hclge_add_mc_addr_common(struct hclge_vport *vport,
 			     const unsigned char *addr)
 {
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 	struct hclge_mac_vlan_tbl_entry_cmd req;
 	struct hclge_desc desc[3];
@@ -8750,9 +8829,10 @@
 
 	/* mac addr check */
 	if (!is_multicast_ether_addr(addr)) {
+		hnae3_format_mac_addr(format_mac_addr, addr);
 		dev_err(&hdev->pdev->dev,
-			"Add mc mac err! invalid mac:%pM.\n",
-			 addr);
+			"Add mc mac err! invalid mac:%s.\n",
+			 format_mac_addr);
 		return -EINVAL;
 	}
 	memset(&req, 0, sizeof(req));
@@ -8788,16 +8868,18 @@
 int hclge_rm_mc_addr_common(struct hclge_vport *vport,
 			    const unsigned char *addr)
 {
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 	struct hclge_mac_vlan_tbl_entry_cmd req;
-	enum hclge_cmd_status status;
+	enum hclge_comm_cmd_status status;
 	struct hclge_desc desc[3];
 
 	/* mac addr check */
 	if (!is_multicast_ether_addr(addr)) {
+		hnae3_format_mac_addr(format_mac_addr, addr);
 		dev_dbg(&hdev->pdev->dev,
-			"Remove mc mac err! invalid mac:%pM.\n",
-			 addr);
+			"Remove mc mac err! invalid mac:%s.\n",
+			 format_mac_addr);
 		return -EINVAL;
 	}
 
@@ -8936,7 +9018,7 @@
 	if (mac_type == HCLGE_MAC_ADDR_UC) {
 		if (is_all_added)
 			vport->overflow_promisc_flags &= ~HNAE3_OVERFLOW_UPE;
-		else
+		else if (hclge_is_umv_space_full(vport, true))
 			vport->overflow_promisc_flags |= HNAE3_OVERFLOW_UPE;
 	} else {
 		if (is_all_added)
@@ -9263,16 +9345,18 @@
 			    u8 *mac_addr)
 {
 	struct hclge_vport *vport = hclge_get_vport(handle);
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 
 	vport = hclge_get_vf_vport(hdev, vf);
 	if (!vport)
 		return -EINVAL;
 
+	hnae3_format_mac_addr(format_mac_addr, mac_addr);
 	if (ether_addr_equal(mac_addr, vport->vf_info.mac)) {
 		dev_info(&hdev->pdev->dev,
-			 "Specified MAC(=%pM) is same as before, no change committed!\n",
-			 mac_addr);
+			 "Specified MAC(=%s) is same as before, no change committed!\n",
+			 format_mac_addr);
 		return 0;
 	}
 
@@ -9284,15 +9368,20 @@
 
 	ether_addr_copy(vport->vf_info.mac, mac_addr);
 
+	/* there is a timewindow for PF to know VF unalive, it may
+	 * cause send mailbox fail, but it doesn't matter, VF will
+	 * query it when reinit.
+	 */
 	if (test_bit(HCLGE_VPORT_STATE_ALIVE, &vport->state)) {
 		dev_info(&hdev->pdev->dev,
-			 "MAC of VF %d has been set to %pM, and it will be reinitialized!\n",
-			 vf, mac_addr);
-		return hclge_inform_reset_assert_to_vf(vport);
+			 "MAC of VF %d has been set to %s, and it will be reinitialized!\n",
+			 vf, format_mac_addr);
+		(void)hclge_inform_reset_assert_to_vf(vport);
+		return 0;
 	}
 
-	dev_info(&hdev->pdev->dev, "MAC of VF %d has been set to %pM\n",
-		 vf, mac_addr);
+	dev_info(&hdev->pdev->dev, "MAC of VF %d has been set to %s\n",
+		 vf, format_mac_addr);
 	return 0;
 }
 
@@ -9391,11 +9480,12 @@
 	return 0;
 }
 
-static int hclge_set_mac_addr(struct hnae3_handle *handle, void *p,
+static int hclge_set_mac_addr(struct hnae3_handle *handle, const void *p,
 			      bool is_first)
 {
 	const unsigned char *new_addr = (const unsigned char *)p;
 	struct hclge_vport *vport = hclge_get_vport(handle);
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclge_dev *hdev = vport->back;
 	unsigned char *old_addr = NULL;
 	int ret;
@@ -9404,9 +9494,10 @@
 	if (is_zero_ether_addr(new_addr) ||
 	    is_broadcast_ether_addr(new_addr) ||
 	    is_multicast_ether_addr(new_addr)) {
+		hnae3_format_mac_addr(format_mac_addr, new_addr);
 		dev_err(&hdev->pdev->dev,
-			"change uc mac err! invalid mac: %pM.\n",
-			 new_addr);
+			"change uc mac err! invalid mac: %s.\n",
+			 format_mac_addr);
 		return -EINVAL;
 	}
 
@@ -9424,9 +9515,10 @@
 	spin_lock_bh(&vport->mac_list_lock);
 	ret = hclge_update_mac_node_for_dev_addr(vport, old_addr, new_addr);
 	if (ret) {
+		hnae3_format_mac_addr(format_mac_addr, new_addr);
 		dev_err(&hdev->pdev->dev,
-			"failed to change the mac addr:%pM, ret = %d\n",
-			new_addr, ret);
+			"failed to change the mac addr:%s, ret = %d\n",
+			format_mac_addr, ret);
 		spin_unlock_bh(&vport->mac_list_lock);
 
 		if (!is_first)
@@ -10015,67 +10107,85 @@
 	return status;
 }
 
-static int hclge_init_vlan_config(struct hclge_dev *hdev)
+static int hclge_init_vlan_filter(struct hclge_dev *hdev)
 {
-#define HCLGE_DEF_VLAN_TYPE		0x8100
-
-	struct hnae3_handle *handle = &hdev->vport[0].nic;
 	struct hclge_vport *vport;
+	bool enable = true;
 	int ret;
 	int i;
 
-	if (hdev->ae_dev->dev_version >= HNAE3_DEVICE_VERSION_V2) {
-		/* for revision 0x21, vf vlan filter is per function */
-		for (i = 0; i < hdev->num_alloc_vport; i++) {
-			vport = &hdev->vport[i];
-			ret = hclge_set_vlan_filter_ctrl(hdev,
-							 HCLGE_FILTER_TYPE_VF,
-							 HCLGE_FILTER_FE_EGRESS,
-							 true,
-							 vport->vport_id);
-			if (ret)
-				return ret;
-			vport->cur_vlan_fltr_en = true;
-		}
+	if (hdev->ae_dev->dev_version < HNAE3_DEVICE_VERSION_V2)
+		return hclge_set_vlan_filter_ctrl(hdev, HCLGE_FILTER_TYPE_VF,
+						  HCLGE_FILTER_FE_EGRESS_V1_B,
+						  true, 0);
 
-		ret = hclge_set_vlan_filter_ctrl(hdev, HCLGE_FILTER_TYPE_PORT,
-						 HCLGE_FILTER_FE_INGRESS, true,
-						 0);
-		if (ret)
-			return ret;
-	} else {
+	/* for revision 0x21, vf vlan filter is per function */
+	for (i = 0; i < hdev->num_alloc_vport; i++) {
+		vport = &hdev->vport[i];
 		ret = hclge_set_vlan_filter_ctrl(hdev, HCLGE_FILTER_TYPE_VF,
-						 HCLGE_FILTER_FE_EGRESS_V1_B,
-						 true, 0);
+						 HCLGE_FILTER_FE_EGRESS, true,
+						 vport->vport_id);
 		if (ret)
 			return ret;
+		vport->cur_vlan_fltr_en = true;
 	}
 
-	hdev->vlan_type_cfg.rx_in_fst_vlan_type = HCLGE_DEF_VLAN_TYPE;
-	hdev->vlan_type_cfg.rx_in_sec_vlan_type = HCLGE_DEF_VLAN_TYPE;
-	hdev->vlan_type_cfg.rx_ot_fst_vlan_type = HCLGE_DEF_VLAN_TYPE;
-	hdev->vlan_type_cfg.rx_ot_sec_vlan_type = HCLGE_DEF_VLAN_TYPE;
-	hdev->vlan_type_cfg.tx_ot_vlan_type = HCLGE_DEF_VLAN_TYPE;
-	hdev->vlan_type_cfg.tx_in_vlan_type = HCLGE_DEF_VLAN_TYPE;
+	if (test_bit(HNAE3_DEV_SUPPORT_VLAN_FLTR_MDF_B, hdev->ae_dev->caps) &&
+	    !test_bit(HNAE3_DEV_SUPPORT_PORT_VLAN_BYPASS_B, hdev->ae_dev->caps))
+		enable = false;
 
-	ret = hclge_set_vlan_protocol_type(hdev);
-	if (ret)
-		return ret;
+	return hclge_set_vlan_filter_ctrl(hdev, HCLGE_FILTER_TYPE_PORT,
+					  HCLGE_FILTER_FE_INGRESS, enable, 0);
+}
 
-	for (i = 0; i < hdev->num_alloc_vport; i++) {
-		u16 vlan_tag;
-		u8 qos;
+static int hclge_init_vlan_type(struct hclge_dev *hdev)
+{
+	hdev->vlan_type_cfg.rx_in_fst_vlan_type = ETH_P_8021Q;
+	hdev->vlan_type_cfg.rx_in_sec_vlan_type = ETH_P_8021Q;
+	hdev->vlan_type_cfg.rx_ot_fst_vlan_type = ETH_P_8021Q;
+	hdev->vlan_type_cfg.rx_ot_sec_vlan_type = ETH_P_8021Q;
+	hdev->vlan_type_cfg.tx_ot_vlan_type = ETH_P_8021Q;
+	hdev->vlan_type_cfg.tx_in_vlan_type = ETH_P_8021Q;
 
+	return hclge_set_vlan_protocol_type(hdev);
+}
+
+static int hclge_init_vport_vlan_offload(struct hclge_dev *hdev)
+{
+	struct hclge_port_base_vlan_config *cfg;
+	struct hclge_vport *vport;
+	int ret;
+	int i;
+
+	for (i = 0; i < hdev->num_alloc_vport; i++) {
 		vport = &hdev->vport[i];
-		vlan_tag = vport->port_base_vlan_cfg.vlan_info.vlan_tag;
-		qos = vport->port_base_vlan_cfg.vlan_info.qos;
+		cfg = &vport->port_base_vlan_cfg;
 
-		ret = hclge_vlan_offload_cfg(vport,
-					     vport->port_base_vlan_cfg.state,
-					     vlan_tag, qos);
+		ret = hclge_vlan_offload_cfg(vport, cfg->state,
+					     cfg->vlan_info.vlan_tag,
+					     cfg->vlan_info.qos);
 		if (ret)
 			return ret;
 	}
+	return 0;
+}
+
+static int hclge_init_vlan_config(struct hclge_dev *hdev)
+{
+	struct hnae3_handle *handle = &hdev->vport[0].nic;
+	int ret;
+
+	ret = hclge_init_vlan_filter(hdev);
+	if (ret)
+		return ret;
+
+	ret = hclge_init_vlan_type(hdev);
+	if (ret)
+		return ret;
+
+	ret = hclge_init_vport_vlan_offload(hdev);
+	if (ret)
+		return ret;
 
 	return hclge_set_vlan_filter(handle, htons(ETH_P_8021Q), 0, false);
 }
@@ -10084,19 +10194,28 @@
 				       bool writen_to_tbl)
 {
 	struct hclge_vport_vlan_cfg *vlan, *tmp;
+	struct hclge_dev *hdev = vport->back;
 
-	list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node)
-		if (vlan->vlan_id == vlan_id)
+	mutex_lock(&hdev->vport_lock);
+
+	list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) {
+		if (vlan->vlan_id == vlan_id) {
+			mutex_unlock(&hdev->vport_lock);
 			return;
+		}
+	}
 
 	vlan = kzalloc(sizeof(*vlan), GFP_KERNEL);
-	if (!vlan)
+	if (!vlan) {
+		mutex_unlock(&hdev->vport_lock);
 		return;
+	}
 
 	vlan->hd_tbl_status = writen_to_tbl;
 	vlan->vlan_id = vlan_id;
 
 	list_add_tail(&vlan->node, &vport->vlan_list);
+	mutex_unlock(&hdev->vport_lock);
 }
 
 static int hclge_add_vport_all_vlan_table(struct hclge_vport *vport)
@@ -10105,6 +10224,8 @@
 	struct hclge_dev *hdev = vport->back;
 	int ret;
 
+	mutex_lock(&hdev->vport_lock);
+
 	list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) {
 		if (!vlan->hd_tbl_status) {
 			ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q),
@@ -10114,12 +10235,16 @@
 				dev_err(&hdev->pdev->dev,
 					"restore vport vlan list failed, ret=%d\n",
 					ret);
+
+				mutex_unlock(&hdev->vport_lock);
 				return ret;
 			}
 		}
 		vlan->hd_tbl_status = true;
 	}
 
+	mutex_unlock(&hdev->vport_lock);
+
 	return 0;
 }
 
@@ -10150,6 +10275,8 @@
 	struct hclge_vport_vlan_cfg *vlan, *tmp;
 	struct hclge_dev *hdev = vport->back;
 
+	mutex_lock(&hdev->vport_lock);
+
 	list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) {
 		if (vlan->hd_tbl_status)
 			hclge_set_vlan_filter_hw(hdev,
@@ -10165,6 +10292,7 @@
 		}
 	}
 	clear_bit(vport->vport_id, hdev->vf_vlan_full);
+	mutex_unlock(&hdev->vport_lock);
 }
 
 void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev)
@@ -10173,6 +10301,8 @@
 	struct hclge_vport *vport;
 	int i;
 
+	mutex_lock(&hdev->vport_lock);
+
 	for (i = 0; i < hdev->num_alloc_vport; i++) {
 		vport = &hdev->vport[i];
 		list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) {
@@ -10180,37 +10310,61 @@
 			kfree(vlan);
 		}
 	}
+
+	mutex_unlock(&hdev->vport_lock);
 }
 
-void hclge_restore_vport_vlan_table(struct hclge_vport *vport)
+void hclge_restore_vport_port_base_vlan_config(struct hclge_dev *hdev)
 {
-	struct hclge_vport_vlan_cfg *vlan, *tmp;
-	struct hclge_dev *hdev = vport->back;
+	struct hclge_vlan_info *vlan_info;
+	struct hclge_vport *vport;
 	u16 vlan_proto;
 	u16 vlan_id;
 	u16 state;
+	int vf_id;
 	int ret;
 
-	vlan_proto = vport->port_base_vlan_cfg.vlan_info.vlan_proto;
-	vlan_id = vport->port_base_vlan_cfg.vlan_info.vlan_tag;
-	state = vport->port_base_vlan_cfg.state;
-
-	if (state != HNAE3_PORT_BASE_VLAN_DISABLE) {
-		clear_bit(vport->vport_id, hdev->vlan_table[vlan_id]);
-		hclge_set_vlan_filter_hw(hdev, htons(vlan_proto),
-					 vport->vport_id, vlan_id,
-					 false);
-		return;
+	/* PF should restore all vfs port base vlan */
+	for (vf_id = 0; vf_id < hdev->num_alloc_vfs; vf_id++) {
+		vport = &hdev->vport[vf_id + HCLGE_VF_VPORT_START_NUM];
+		vlan_info = vport->port_base_vlan_cfg.tbl_sta ?
+			    &vport->port_base_vlan_cfg.vlan_info :
+			    &vport->port_base_vlan_cfg.old_vlan_info;
+
+		vlan_id = vlan_info->vlan_tag;
+		vlan_proto = vlan_info->vlan_proto;
+		state = vport->port_base_vlan_cfg.state;
+
+		if (state != HNAE3_PORT_BASE_VLAN_DISABLE) {
+			clear_bit(vport->vport_id, hdev->vlan_table[vlan_id]);
+			ret = hclge_set_vlan_filter_hw(hdev, htons(vlan_proto),
+						       vport->vport_id,
+						       vlan_id, false);
+			vport->port_base_vlan_cfg.tbl_sta = ret == 0;
+		}
 	}
+}
 
-	list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) {
-		ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q),
-					       vport->vport_id,
-					       vlan->vlan_id, false);
-		if (ret)
-			break;
-		vlan->hd_tbl_status = true;
+void hclge_restore_vport_vlan_table(struct hclge_vport *vport)
+{
+	struct hclge_vport_vlan_cfg *vlan, *tmp;
+	struct hclge_dev *hdev = vport->back;
+	int ret;
+
+	mutex_lock(&hdev->vport_lock);
+
+	if (vport->port_base_vlan_cfg.state == HNAE3_PORT_BASE_VLAN_DISABLE) {
+		list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) {
+			ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q),
+						       vport->vport_id,
+						       vlan->vlan_id, false);
+			if (ret)
+				break;
+			vlan->hd_tbl_status = true;
+		}
 	}
+
+	mutex_unlock(&hdev->vport_lock);
 }
 
 /* For global reset and imp reset, hardware will clear the mac table,
@@ -10250,6 +10404,7 @@
 	struct hnae3_handle *handle = &vport->nic;
 
 	hclge_restore_mac_table_common(vport);
+	hclge_restore_vport_port_base_vlan_config(hdev);
 	hclge_restore_vport_vlan_table(vport);
 	set_bit(HCLGE_STATE_FD_USER_DEF_CHANGED, &hdev->state);
 	hclge_restore_fd_entries(handle);
@@ -10306,6 +10461,8 @@
 						 false);
 	}
 
+	vport->port_base_vlan_cfg.tbl_sta = false;
+
 	/* force add VLAN 0 */
 	ret = hclge_set_vf_vlan_common(hdev, vport->vport_id, false, 0);
 	if (ret)
@@ -10332,12 +10489,42 @@
 	return false;
 }
 
+static int hclge_modify_port_base_vlan_tag(struct hclge_vport *vport,
+					   struct hclge_vlan_info *new_info,
+					   struct hclge_vlan_info *old_info)
+{
+	struct hclge_dev *hdev = vport->back;
+	int ret;
+
+	/* add new VLAN tag */
+	ret = hclge_set_vlan_filter_hw(hdev, htons(new_info->vlan_proto),
+				       vport->vport_id, new_info->vlan_tag,
+				       false);
+	if (ret)
+		return ret;
+
+	vport->port_base_vlan_cfg.tbl_sta = false;
+	/* remove old VLAN tag */
+	if (old_info->vlan_tag == 0)
+		ret = hclge_set_vf_vlan_common(hdev, vport->vport_id,
+					       true, 0);
+	else
+		ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q),
+					       vport->vport_id,
+					       old_info->vlan_tag, true);
+	if (ret)
+		dev_err(&hdev->pdev->dev,
+			"failed to clear vport%u port base vlan %u, ret = %d.\n",
+			vport->vport_id, old_info->vlan_tag, ret);
+
+	return ret;
+}
+
 int hclge_update_port_base_vlan_cfg(struct hclge_vport *vport, u16 state,
 				    struct hclge_vlan_info *vlan_info)
 {
 	struct hnae3_handle *nic = &vport->nic;
 	struct hclge_vlan_info *old_vlan_info;
-	struct hclge_dev *hdev = vport->back;
 	int ret;
 
 	old_vlan_info = &vport->port_base_vlan_cfg.vlan_info;
@@ -10350,38 +10537,12 @@
 	if (!hclge_need_update_vlan_filter(vlan_info, old_vlan_info))
 		goto out;
 
-	if (state == HNAE3_PORT_BASE_VLAN_MODIFY) {
-		/* add new VLAN tag */
-		ret = hclge_set_vlan_filter_hw(hdev,
-					       htons(vlan_info->vlan_proto),
-					       vport->vport_id,
-					       vlan_info->vlan_tag,
-					       false);
-		if (ret)
-			return ret;
-
-		/* remove old VLAN tag */
-		if (old_vlan_info->vlan_tag == 0)
-			ret = hclge_set_vf_vlan_common(hdev, vport->vport_id,
-						       true, 0);
-		else
-			ret = hclge_set_vlan_filter_hw(hdev,
-						       htons(ETH_P_8021Q),
-						       vport->vport_id,
-						       old_vlan_info->vlan_tag,
-						       true);
-		if (ret) {
-			dev_err(&hdev->pdev->dev,
-				"failed to clear vport%u port base vlan %u, ret = %d.\n",
-				vport->vport_id, old_vlan_info->vlan_tag, ret);
-			return ret;
-		}
-
-		goto out;
-	}
-
-	ret = hclge_update_vlan_filter_entries(vport, state, vlan_info,
-					       old_vlan_info);
+	if (state == HNAE3_PORT_BASE_VLAN_MODIFY)
+		ret = hclge_modify_port_base_vlan_tag(vport, vlan_info,
+						      old_vlan_info);
+	else
+		ret = hclge_update_vlan_filter_entries(vport, state, vlan_info,
+						       old_vlan_info);
 	if (ret)
 		return ret;
 
@@ -10392,7 +10553,9 @@
 	else
 		nic->port_base_vlan_state = HNAE3_PORT_BASE_VLAN_ENABLE;
 
+	vport->port_base_vlan_cfg.old_vlan_info = *old_vlan_info;
 	vport->port_base_vlan_cfg.vlan_info = *vlan_info;
+	vport->port_base_vlan_cfg.tbl_sta = true;
 	hclge_set_vport_vlan_fltr_change(vport);
 
 	return 0;
@@ -10460,14 +10623,17 @@
 		return ret;
 	}
 
-	/* for DEVICE_VERSION_V3, vf doesn't need to know about the port based
+	/* there is a timewindow for PF to know VF unalive, it may
+	 * cause send mailbox fail, but it doesn't matter, VF will
+	 * query it when reinit.
+	 * for DEVICE_VERSION_V3, vf doesn't need to know about the port based
 	 * VLAN state.
 	 */
 	if (ae_dev->dev_version < HNAE3_DEVICE_VERSION_V3 &&
 	    test_bit(HCLGE_VPORT_STATE_ALIVE, &vport->state))
-		hclge_push_vf_port_base_vlan_info(&hdev->vport[0],
-						  vport->vport_id, state,
-						  &vlan_info);
+		(void)hclge_push_vf_port_base_vlan_info(&hdev->vport[0],
+							vport->vport_id,
+							state, &vlan_info);
 
 	return 0;
 }
@@ -10506,11 +10672,16 @@
 	 * handle mailbox. Just record the vlan id, and remove it after
 	 * reset finished.
 	 */
+	mutex_lock(&hdev->vport_lock);
 	if ((test_bit(HCLGE_STATE_RST_HANDLING, &hdev->state) ||
 	     test_bit(HCLGE_STATE_RST_FAIL, &hdev->state)) && is_kill) {
 		set_bit(vlan_id, vport->vlan_del_fail_bmap);
+		mutex_unlock(&hdev->vport_lock);
 		return -EBUSY;
+	} else if (!is_kill && test_bit(vlan_id, vport->vlan_del_fail_bmap)) {
+		clear_bit(vlan_id, vport->vlan_del_fail_bmap);
 	}
+	mutex_unlock(&hdev->vport_lock);
 
 	/* when port base vlan enabled, we use port base vlan as the vlan
 	 * filter entry. In this case, we don't update vlan filter table
@@ -10525,17 +10696,22 @@
 	}
 
 	if (!ret) {
-		if (is_kill)
-			hclge_rm_vport_vlan_table(vport, vlan_id, false);
-		else
+		if (!is_kill) {
 			hclge_add_vport_vlan_table(vport, vlan_id,
 						   writen_to_tbl);
+		} else if (is_kill && vlan_id != 0) {
+			mutex_lock(&hdev->vport_lock);
+			hclge_rm_vport_vlan_table(vport, vlan_id, false);
+			mutex_unlock(&hdev->vport_lock);
+		}
 	} else if (is_kill) {
 		/* when remove hw vlan filter failed, record the vlan id,
 		 * and try to remove it from hw later, to be consistence
 		 * with stack
 		 */
+		mutex_lock(&hdev->vport_lock);
 		set_bit(vlan_id, vport->vlan_del_fail_bmap);
+		mutex_unlock(&hdev->vport_lock);
 	}
 
 	hclge_set_vport_vlan_fltr_change(vport);
@@ -10575,6 +10751,7 @@
 	int i, ret, sync_cnt = 0;
 	u16 vlan_id;
 
+	mutex_lock(&hdev->vport_lock);
 	/* start from vport 1 for PF is always alive */
 	for (i = 0; i < hdev->num_alloc_vport; i++) {
 		struct hclge_vport *vport = &hdev->vport[i];
@@ -10585,21 +10762,26 @@
 			ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q),
 						       vport->vport_id, vlan_id,
 						       true);
-			if (ret && ret != -EINVAL)
+			if (ret && ret != -EINVAL) {
+				mutex_unlock(&hdev->vport_lock);
 				return;
+			}
 
 			clear_bit(vlan_id, vport->vlan_del_fail_bmap);
 			hclge_rm_vport_vlan_table(vport, vlan_id, false);
 			hclge_set_vport_vlan_fltr_change(vport);
 
 			sync_cnt++;
-			if (sync_cnt >= HCLGE_MAX_SYNC_COUNT)
+			if (sync_cnt >= HCLGE_MAX_SYNC_COUNT) {
+				mutex_unlock(&hdev->vport_lock);
 				return;
+			}
 
 			vlan_id = find_first_bit(vport->vlan_del_fail_bmap,
 						 VLAN_N_VID);
 		}
 	}
+	mutex_unlock(&hdev->vport_lock);
 
 	hclge_sync_vlan_fltr_state(hdev);
 }
@@ -10892,9 +11074,12 @@
 	u32 rx_pause, tx_pause;
 	u8 flowctl;
 
-	if (!phydev->link || !phydev->autoneg)
+	if (!phydev->link)
 		return 0;
 
+	if (!phydev->autoneg)
+		return hclge_mac_pause_setup_hw(hdev);
+
 	local_advertising = linkmode_adv_to_lcl_adv_t(phydev->advertising);
 
 	if (phydev->pause)
@@ -11083,6 +11268,7 @@
 
 static void hclge_info_show(struct hclge_dev *hdev)
 {
+	struct hnae3_handle *handle = &hdev->vport->nic;
 	struct device *dev = &hdev->pdev->dev;
 
 	dev_info(dev, "PF info begin:\n");
@@ -11099,9 +11285,9 @@
 	dev_info(dev, "This is %s PF\n",
 		 hdev->flag & HCLGE_FLAG_MAIN ? "main" : "not main");
 	dev_info(dev, "DCB %s\n",
-		 hdev->flag & HCLGE_FLAG_DCB_ENABLE ? "enable" : "disable");
+		 handle->kinfo.tc_info.dcb_ets_active ? "enable" : "disable");
 	dev_info(dev, "MQPRIO %s\n",
-		 hdev->flag & HCLGE_FLAG_MQPRIO_ENABLE ? "enable" : "disable");
+		 handle->kinfo.tc_info.mqprio_active ? "enable" : "disable");
 	dev_info(dev, "Default tx spare buffer size: %u\n",
 		 hdev->tx_spare_buf_size);
 
@@ -11250,6 +11436,12 @@
 	return ret;
 }
 
+static bool hclge_uninit_need_wait(struct hclge_dev *hdev)
+{
+	return test_bit(HCLGE_STATE_RST_HANDLING, &hdev->state) ||
+	       test_bit(HCLGE_STATE_LINK_UPDATING, &hdev->state);
+}
+
 static void hclge_uninit_client_instance(struct hnae3_client *client,
 					 struct hnae3_ae_dev *ae_dev)
 {
@@ -11258,7 +11450,7 @@
 
 	if (hdev->roce_client) {
 		clear_bit(HCLGE_STATE_ROCE_REGISTERED, &hdev->state);
-		while (test_bit(HCLGE_STATE_RST_HANDLING, &hdev->state))
+		while (hclge_uninit_need_wait(hdev))
 			msleep(HCLGE_WAIT_RESET_DONE);
 
 		hdev->roce_client->ops->uninit_instance(&vport->roce, 0);
@@ -11289,10 +11481,11 @@
 	if (!(pci_select_bars(pdev, IORESOURCE_MEM) & BIT(HCLGE_MEM_BAR)))
 		return 0;
 
-	hw->mem_base = devm_ioremap_wc(&pdev->dev,
-				       pci_resource_start(pdev, HCLGE_MEM_BAR),
-				       pci_resource_len(pdev, HCLGE_MEM_BAR));
-	if (!hw->mem_base) {
+	hw->hw.mem_base =
+		devm_ioremap_wc(&pdev->dev,
+				pci_resource_start(pdev, HCLGE_MEM_BAR),
+				pci_resource_len(pdev, HCLGE_MEM_BAR));
+	if (!hw->hw.mem_base) {
 		dev_err(&pdev->dev, "failed to map device memory\n");
 		return -EFAULT;
 	}
@@ -11331,8 +11524,8 @@
 
 	pci_set_master(pdev);
 	hw = &hdev->hw;
-	hw->io_base = pcim_iomap(pdev, 2, 0);
-	if (!hw->io_base) {
+	hw->hw.io_base = pcim_iomap(pdev, 2, 0);
+	if (!hw->hw.io_base) {
 		dev_err(&pdev->dev, "Can't map configuration register space\n");
 		ret = -ENOMEM;
 		goto err_clr_master;
@@ -11347,7 +11540,7 @@
 	return 0;
 
 err_unmap_io_base:
-	pcim_iounmap(pdev, hdev->hw.io_base);
+	pcim_iounmap(pdev, hdev->hw.hw.io_base);
 err_clr_master:
 	pci_clear_master(pdev);
 	pci_release_regions(pdev);
@@ -11361,10 +11554,10 @@
 {
 	struct pci_dev *pdev = hdev->pdev;
 
-	if (hdev->hw.mem_base)
-		devm_iounmap(&pdev->dev, hdev->hw.mem_base);
+	if (hdev->hw.hw.mem_base)
+		devm_iounmap(&pdev->dev, hdev->hw.hw.mem_base);
 
-	pcim_iounmap(pdev, hdev->hw.io_base);
+	pcim_iounmap(pdev, hdev->hw.hw.io_base);
 	pci_free_irq_vectors(pdev);
 	pci_clear_master(pdev);
 	pci_release_mem_regions(pdev);
@@ -11425,7 +11618,7 @@
 
 	/* disable misc vector before reset done */
 	hclge_enable_vector(&hdev->misc_vector, false);
-	set_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state);
+	set_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state);
 
 	if (hdev->reset_type == HNAE3_FLR_RESET)
 		hdev->rst_stats.flr_rst_cnt++;
@@ -11443,8 +11636,8 @@
 		dev_err(&hdev->pdev->dev, "fail to rebuild, ret=%d\n", ret);
 
 	hdev->reset_type = HNAE3_NONE_RESET;
-	clear_bit(HCLGE_STATE_RST_HANDLING, &hdev->state);
-	up(&hdev->reset_sem);
+	if (test_and_clear_bit(HCLGE_STATE_RST_HANDLING, &hdev->state))
+		up(&hdev->reset_sem);
 }
 
 static void hclge_clear_resetting_state(struct hclge_dev *hdev)
@@ -11584,9 +11777,13 @@
 	if (ret)
 		goto err_msi_irq_uninit;
 
-	if (hdev->hw.mac.media_type == HNAE3_MEDIA_TYPE_COPPER &&
-	    !hnae3_dev_phy_imp_supported(hdev)) {
-		ret = hclge_mac_mdio_config(hdev);
+	if (hdev->hw.mac.media_type == HNAE3_MEDIA_TYPE_COPPER) {
+		clear_bit(HNAE3_DEV_SUPPORT_FEC_B, ae_dev->caps);
+		if (hnae3_dev_phy_imp_supported(hdev))
+			ret = hclge_update_tp_port_info(hdev);
+		else
+			ret = hclge_mac_mdio_config(hdev);
+
 		if (ret)
 			goto err_msi_irq_uninit;
 	}
@@ -11712,7 +11909,7 @@
 err_devlink_uninit:
 	hclge_devlink_uninit(hdev);
 err_pci_uninit:
-	pcim_iounmap(pdev, hdev->hw.io_base);
+	pcim_iounmap(pdev, hdev->hw.hw.io_base);
 	pci_clear_master(pdev);
 	pci_release_regions(pdev);
 	pci_disable_device(pdev);
@@ -12103,8 +12300,8 @@
 	hclge_misc_irq_uninit(hdev);
 	hclge_devlink_uninit(hdev);
 	hclge_pci_uninit(hdev);
-	mutex_destroy(&hdev->vport_lock);
 	hclge_uninit_vport_vlan_table(hdev);
+	mutex_destroy(&hdev->vport_lock);
 	ae_dev->priv = NULL;
 }
 
@@ -12736,60 +12933,71 @@
 	return ret;
 }
 
-static void hclge_sync_promisc_mode(struct hclge_dev *hdev)
+static int hclge_sync_vport_promisc_mode(struct hclge_vport *vport)
 {
-	struct hclge_vport *vport = &hdev->vport[0];
 	struct hnae3_handle *handle = &vport->nic;
+	struct hclge_dev *hdev = vport->back;
+	bool uc_en = false;
+	bool mc_en = false;
 	u8 tmp_flags;
+	bool bc_en;
 	int ret;
-	u16 i;
 
 	if (vport->last_promisc_flags != vport->overflow_promisc_flags) {
 		set_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE, &vport->state);
 		vport->last_promisc_flags = vport->overflow_promisc_flags;
 	}
 
-	if (test_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE, &vport->state)) {
+	if (!test_and_clear_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE,
+				&vport->state))
+		return 0;
+
+	/* for PF */
+	if (!vport->vport_id) {
 		tmp_flags = handle->netdev_flags | vport->last_promisc_flags;
 		ret = hclge_set_promisc_mode(handle, tmp_flags & HNAE3_UPE,
 					     tmp_flags & HNAE3_MPE);
-		if (!ret) {
-			clear_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE,
-				  &vport->state);
+		if (!ret)
 			set_bit(HCLGE_VPORT_STATE_VLAN_FLTR_CHANGE,
 				&vport->state);
-		}
+		else
+			set_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE,
+				&vport->state);
+		return ret;
 	}
 
-	for (i = 1; i < hdev->num_alloc_vport; i++) {
-		bool uc_en = false;
-		bool mc_en = false;
-		bool bc_en;
+	/* for VF */
+	if (vport->vf_info.trusted) {
+		uc_en = vport->vf_info.request_uc_en > 0 ||
+			vport->overflow_promisc_flags & HNAE3_OVERFLOW_UPE;
+		mc_en = vport->vf_info.request_mc_en > 0 ||
+			vport->overflow_promisc_flags & HNAE3_OVERFLOW_MPE;
+	}
+	bc_en = vport->vf_info.request_bc_en > 0;
 
-		vport = &hdev->vport[i];
+	ret = hclge_cmd_set_promisc_mode(hdev, vport->vport_id, uc_en,
+					 mc_en, bc_en);
+	if (ret) {
+		set_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE, &vport->state);
+		return ret;
+	}
+	hclge_set_vport_vlan_fltr_change(vport);
 
-		if (!test_and_clear_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE,
-					&vport->state))
-			continue;
+	return 0;
+}
 
-		if (vport->vf_info.trusted) {
-			uc_en = vport->vf_info.request_uc_en > 0 ||
-				vport->overflow_promisc_flags &
-				HNAE3_OVERFLOW_UPE;
-			mc_en = vport->vf_info.request_mc_en > 0 ||
-				vport->overflow_promisc_flags &
-				HNAE3_OVERFLOW_MPE;
-		}
-		bc_en = vport->vf_info.request_bc_en > 0;
+static void hclge_sync_promisc_mode(struct hclge_dev *hdev)
+{
+	struct hclge_vport *vport;
+	int ret;
+	u16 i;
 
-		ret = hclge_cmd_set_promisc_mode(hdev, vport->vport_id, uc_en,
-						 mc_en, bc_en);
-		if (ret) {
-			set_bit(HCLGE_VPORT_STATE_PROMISC_CHANGE,
-				&vport->state);
+	for (i = 0; i < hdev->num_alloc_vport; i++) {
+		vport = &hdev->vport[i];
+
+		ret = hclge_sync_vport_promisc_mode(vport);
+		if (ret)
 			return;
-		}
-		hclge_set_vport_vlan_fltr_change(vport);
 	}
 }
 
@@ -12917,6 +13125,55 @@
 	return 0;
 }
 
+/* After disable sriov, VF still has some config and info need clean,
+ * which configed by PF.
+ */
+static void hclge_clear_vport_vf_info(struct hclge_vport *vport, int vfid)
+{
+	struct hclge_dev *hdev = vport->back;
+	struct hclge_vlan_info vlan_info;
+	int ret;
+
+	/* after disable sriov, clean VF rate configured by PF */
+	ret = hclge_tm_qs_shaper_cfg(vport, 0);
+	if (ret)
+		dev_err(&hdev->pdev->dev,
+			"failed to clean vf%d rate config, ret = %d\n",
+			vfid, ret);
+
+	vlan_info.vlan_tag = 0;
+	vlan_info.qos = 0;
+	vlan_info.vlan_proto = ETH_P_8021Q;
+	ret = hclge_update_port_base_vlan_cfg(vport,
+					      HNAE3_PORT_BASE_VLAN_DISABLE,
+					      &vlan_info);
+	if (ret)
+		dev_err(&hdev->pdev->dev,
+			"failed to clean vf%d port base vlan, ret = %d\n",
+			vfid, ret);
+
+	ret = hclge_set_vf_spoofchk_hw(hdev, vport->vport_id, false);
+	if (ret)
+		dev_err(&hdev->pdev->dev,
+			"failed to clean vf%d spoof config, ret = %d\n",
+			vfid, ret);
+
+	memset(&vport->vf_info, 0, sizeof(vport->vf_info));
+}
+
+static void hclge_clean_vport_config(struct hnae3_ae_dev *ae_dev, int num_vfs)
+{
+	struct hclge_dev *hdev = ae_dev->priv;
+	struct hclge_vport *vport;
+	int i;
+
+	for (i = 0; i < num_vfs; i++) {
+		vport = &hdev->vport[i + HCLGE_VF_VPORT_START_NUM];
+
+		hclge_clear_vport_vf_info(vport, i);
+	}
+}
+
 static const struct hnae3_ae_ops hclge_ops = {
 	.init_ae_dev = hclge_init_ae_dev,
 	.uninit_ae_dev = hclge_uninit_ae_dev,
@@ -13018,6 +13275,7 @@
 	.get_rx_hwts = hclge_ptp_get_rx_hwts,
 	.get_ts_info = hclge_ptp_get_ts_info,
 	.get_link_diagnosis_info = hclge_get_link_diagnosis_info,
+	.clean_vf_config = hclge_clean_vport_config,
 };
 
 static struct hnae3_ae_algo ae_algo = {
@@ -13042,9 +13300,11 @@
 
 static void hclge_exit(void)
 {
+	hnae3_acquire_unload_lock();
 	hnae3_unregister_ae_algo_prepare(&ae_algo);
 	hnae3_unregister_ae_algo(&ae_algo);
 	destroy_workqueue(hclge_wq);
+	hnae3_release_unload_lock();
 }
 module_init(hclge_init);
 module_exit(hclge_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
@@ -228,7 +228,6 @@
 	HCLGE_STATE_MBX_HANDLING,
 	HCLGE_STATE_ERR_SERVICE_SCHED,
 	HCLGE_STATE_STATISTICS_UPDATING,
-	HCLGE_STATE_CMD_DISABLE,
 	HCLGE_STATE_LINK_UPDATING,
 	HCLGE_STATE_RST_FAIL,
 	HCLGE_STATE_FD_TBL_CHANGED,
@@ -275,10 +274,13 @@
 	u8 media_type;	/* port media type, e.g. fibre/copper/backplane */
 	u8 mac_addr[ETH_ALEN];
 	u8 autoneg;
+	u8 req_autoneg;
 	u8 duplex;
+	u8 req_duplex;
 	u8 support_autoneg;
 	u8 speed_type;	/* 0: sfp speed, 1: active speed */
 	u32 speed;
+	u32 req_speed;
 	u32 max_speed;
 	u32 speed_ability; /* speed ability supported by current media */
 	u32 module_type; /* sub media type, e.g. kr/cr/sr/lr */
@@ -294,11 +296,9 @@
 };
 
 struct hclge_hw {
-	void __iomem *io_base;
-	void __iomem *mem_base;
+	struct hclge_comm_hw hw;
 	struct hclge_mac mac;
 	int num_vec;
-	struct hclge_cmq cmq;
 };
 
 /* TQP stats */
@@ -613,6 +613,11 @@
 #define MAX_FD_FILTER_NUM	4096
 #define HCLGE_ARFS_EXPIRE_INTERVAL	5UL
 
+#define hclge_read_dev(a, reg) \
+	hclge_comm_read_reg((a)->hw.io_base, reg)
+#define hclge_write_dev(a, reg, value) \
+	hclge_comm_write_reg((a)->hw.io_base, reg, value)
+
 enum HCLGE_FD_ACTIVE_RULE_TYPE {
 	HCLGE_FD_RULE_NONE,
 	HCLGE_FD_ARFS_ACTIVE,
@@ -824,6 +829,9 @@
 		(y) = (_k_ ^ ~_v_) & (_k_); \
 	} while (0)
 
+#define HCLGE_MAC_STATS_FIELD_OFF(f) (offsetof(struct hclge_mac_stats, f))
+#define HCLGE_STATS_READ(p, offset) (*(u64 *)((u8 *)(p) + (offset)))
+
 #define HCLGE_MAC_TNL_LOG_SIZE	8
 #define HCLGE_VPORT_NUM 256
 struct hclge_dev {
@@ -855,7 +863,7 @@
 
 	u16 fdir_pf_filter_count; /* Num of guaranteed filters for this PF */
 	u16 num_alloc_vport;		/* Num vports this driver supports */
-	u32 numa_node_mask;
+	nodemask_t numa_node_mask;
 	u16 rx_buf_len;
 	u16 num_tx_desc;		/* desc num of per tx queue */
 	u16 num_rx_desc;		/* desc num of per rx queue */
@@ -876,12 +884,10 @@
 	u16 num_msi;
 	u16 num_msi_left;
 	u16 num_msi_used;
-	u32 base_msi_vector;
 	u16 *vector_status;
 	int *vector_irq;
 	u16 num_nic_msi;	/* Num of nic vectors for this PF */
 	u16 num_roce_msi;	/* Num of roce vectors for this PF */
-	int roce_base_vector;
 
 	unsigned long service_timer_period;
 	unsigned long service_timer_previous;
@@ -901,8 +907,6 @@
 
 #define HCLGE_FLAG_MAIN			BIT(0)
 #define HCLGE_FLAG_DCB_CAPABLE		BIT(1)
-#define HCLGE_FLAG_DCB_ENABLE		BIT(2)
-#define HCLGE_FLAG_MQPRIO_ENABLE	BIT(3)
 	u32 flag;
 
 	u32 pkt_buf_size; /* Total pf buf size for tx/rx */
@@ -926,6 +930,8 @@
 	u16 hclge_fd_rule_num;
 	unsigned long serv_processed_cnt;
 	unsigned long last_serv_processed;
+	unsigned long last_rst_scheduled;
+	unsigned long last_mbx_scheduled;
 	unsigned long fd_bmap[BITS_TO_LONGS(MAX_FD_FILTER_NUM)];
 	enum HCLGE_FD_ACTIVE_RULE_TYPE fd_active_type;
 	u8 fd_en;
@@ -999,7 +1005,9 @@
 
 struct hclge_port_base_vlan_config {
 	u16 state;
+	bool tbl_sta;
 	struct hclge_vlan_info vlan_info;
+	struct hclge_vlan_info old_vlan_info;
 };
 
 struct hclge_vf_info {
@@ -1054,6 +1062,7 @@
 	spinlock_t mac_list_lock; /* protect mac address need to add/detele */
 	struct list_head uc_mac_list;   /* Store VF unicast table */
 	struct list_head mc_mac_list;   /* Store VF multicast table */
+
 	struct list_head vlan_list;     /* Store VF vlan table */
 };
 
@@ -1123,6 +1132,7 @@
 void hclge_rm_vport_all_vlan_table(struct hclge_vport *vport, bool is_del_list);
 void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev);
 void hclge_restore_mac_table_common(struct hclge_vport *vport);
+void hclge_restore_vport_port_base_vlan_config(struct hclge_dev *hdev);
 void hclge_restore_vport_vlan_table(struct hclge_vport *vport);
 int hclge_update_port_base_vlan_cfg(struct hclge_vport *vport, u16 state,
 				    struct hclge_vlan_info *vlan_info);
@@ -1138,4 +1148,5 @@
 int hclge_dbg_dump_rst_info(struct hclge_dev *hdev, char *buf, int len);
 int hclge_push_vf_link_status(struct hclge_vport *vport);
 int hclge_enable_vport_vlan_filter(struct hclge_vport *vport, bool request_en);
+int hclge_mac_update_stats(struct hclge_dev *hdev);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mbx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mbx.c
@@ -33,7 +33,7 @@
 {
 	struct hclge_mbx_pf_to_vf_cmd *resp_pf_to_vf;
 	struct hclge_dev *hdev = vport->back;
-	enum hclge_cmd_status status;
+	enum hclge_comm_cmd_status status;
 	struct hclge_desc desc;
 	u16 resp;
 
@@ -56,17 +56,19 @@
 	resp_pf_to_vf->msg_len = vf_to_pf_req->msg_len;
 	resp_pf_to_vf->match_id = vf_to_pf_req->match_id;
 
-	resp_pf_to_vf->msg.code = HCLGE_MBX_PF_VF_RESP;
-	resp_pf_to_vf->msg.vf_mbx_msg_code = vf_to_pf_req->msg.code;
-	resp_pf_to_vf->msg.vf_mbx_msg_subcode = vf_to_pf_req->msg.subcode;
+	resp_pf_to_vf->msg.code = cpu_to_le16(HCLGE_MBX_PF_VF_RESP);
+	resp_pf_to_vf->msg.vf_mbx_msg_code =
+				cpu_to_le16(vf_to_pf_req->msg.code);
+	resp_pf_to_vf->msg.vf_mbx_msg_subcode =
+				cpu_to_le16(vf_to_pf_req->msg.subcode);
 	resp = hclge_errno_to_resp(resp_msg->status);
 	if (resp < SHRT_MAX) {
-		resp_pf_to_vf->msg.resp_status = resp;
+		resp_pf_to_vf->msg.resp_status = cpu_to_le16(resp);
 	} else {
 		dev_warn(&hdev->pdev->dev,
 			 "failed to send response to VF, response status %u is out-of-bound\n",
 			 resp);
-		resp_pf_to_vf->msg.resp_status = EIO;
+		resp_pf_to_vf->msg.resp_status = cpu_to_le16(EIO);
 	}
 
 	if (resp_msg->len > 0)
@@ -90,18 +92,25 @@
 {
 	struct hclge_mbx_pf_to_vf_cmd *resp_pf_to_vf;
 	struct hclge_dev *hdev = vport->back;
-	enum hclge_cmd_status status;
+	enum hclge_comm_cmd_status status;
 	struct hclge_desc desc;
 
+	if (msg_len > HCLGE_MBX_MAX_MSG_SIZE) {
+		dev_err(&hdev->pdev->dev,
+			"msg data length(=%u) exceeds maximum(=%u)\n",
+			msg_len, HCLGE_MBX_MAX_MSG_SIZE);
+		return -EMSGSIZE;
+	}
+
 	resp_pf_to_vf = (struct hclge_mbx_pf_to_vf_cmd *)desc.data;
 
 	hclge_cmd_setup_basic_desc(&desc, HCLGEVF_OPC_MBX_PF_TO_VF, false);
 
 	resp_pf_to_vf->dest_vfid = dest_vfid;
 	resp_pf_to_vf->msg_len = msg_len;
-	resp_pf_to_vf->msg.code = mbx_opcode;
+	resp_pf_to_vf->msg.code = cpu_to_le16(mbx_opcode);
 
-	memcpy(&resp_pf_to_vf->msg.vf_mbx_msg_code, msg, msg_len);
+	memcpy(resp_pf_to_vf->msg.msg_data, msg, msg_len);
 
 	trace_hclge_pf_mbx_send(hdev, resp_pf_to_vf);
 
@@ -117,8 +126,8 @@
 int hclge_inform_reset_assert_to_vf(struct hclge_vport *vport)
 {
 	struct hclge_dev *hdev = vport->back;
+	__le16 msg_data;
 	u16 reset_type;
-	u8 msg_data[2];
 	u8 dest_vfid;
 
 	BUILD_BUG_ON(HNAE3_MAX_RESET > U16_MAX);
@@ -132,10 +141,10 @@
 	else
 		reset_type = HNAE3_VF_FUNC_RESET;
 
-	memcpy(&msg_data[0], &reset_type, sizeof(u16));
+	msg_data = cpu_to_le16(reset_type);
 
 	/* send this requested info to VF */
-	return hclge_send_mbx_msg(vport, msg_data, sizeof(msg_data),
+	return hclge_send_mbx_msg(vport, (u8 *)&msg_data, sizeof(msg_data),
 				  HCLGE_MBX_ASSERTING_RESET, dest_vfid);
 }
 
@@ -175,7 +184,7 @@
 	ring_num = req->msg.ring_num;
 
 	if (ring_num > HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM)
-		return -ENOMEM;
+		return -EINVAL;
 
 	for (i = 0; i < ring_num; i++) {
 		if (req->msg.param[i].tqp_index >= vport->nic.kinfo.rss_size) {
@@ -241,6 +250,81 @@
 	return ret;
 }
 
+static int hclge_query_ring_vector_map(struct hclge_vport *vport,
+				       struct hnae3_ring_chain_node *ring_chain,
+				       struct hclge_desc *desc)
+{
+	struct hclge_ctrl_vector_chain_cmd *req =
+		(struct hclge_ctrl_vector_chain_cmd *)desc->data;
+	struct hclge_dev *hdev = vport->back;
+	u16 tqp_type_and_id;
+	int status;
+
+	hclge_cmd_setup_basic_desc(desc, HCLGE_OPC_ADD_RING_TO_VECTOR, true);
+
+	tqp_type_and_id = le16_to_cpu(req->tqp_type_and_id[0]);
+	hnae3_set_field(tqp_type_and_id, HCLGE_INT_TYPE_M, HCLGE_INT_TYPE_S,
+			hnae3_get_bit(ring_chain->flag, HNAE3_RING_TYPE_B));
+	hnae3_set_field(tqp_type_and_id, HCLGE_TQP_ID_M, HCLGE_TQP_ID_S,
+			ring_chain->tqp_index);
+	req->tqp_type_and_id[0] = cpu_to_le16(tqp_type_and_id);
+	req->vfid = vport->vport_id;
+
+	status = hclge_cmd_send(&hdev->hw, desc, 1);
+	if (status)
+		dev_err(&hdev->pdev->dev,
+			"Get VF ring vector map info fail, status is %d.\n",
+			status);
+
+	return status;
+}
+
+static int hclge_get_vf_ring_vector_map(struct hclge_vport *vport,
+					struct hclge_mbx_vf_to_pf_cmd *req,
+					struct hclge_respond_to_vf_msg *resp)
+{
+#define HCLGE_LIMIT_RING_NUM			1
+#define HCLGE_RING_TYPE_OFFSET			0
+#define HCLGE_TQP_INDEX_OFFSET			1
+#define HCLGE_INT_GL_INDEX_OFFSET		2
+#define HCLGE_VECTOR_ID_OFFSET			3
+#define HCLGE_RING_VECTOR_MAP_INFO_LEN		4
+	struct hnae3_ring_chain_node ring_chain;
+	struct hclge_desc desc;
+	struct hclge_ctrl_vector_chain_cmd *data =
+		(struct hclge_ctrl_vector_chain_cmd *)desc.data;
+	u16 tqp_type_and_id;
+	u8 int_gl_index;
+	int ret;
+
+	req->msg.ring_num = HCLGE_LIMIT_RING_NUM;
+
+	memset(&ring_chain, 0, sizeof(ring_chain));
+	ret = hclge_get_ring_chain_from_mbx(req, &ring_chain, vport);
+	if (ret)
+		return ret;
+
+	ret = hclge_query_ring_vector_map(vport, &ring_chain, &desc);
+	if (ret) {
+		hclge_free_vector_ring_chain(&ring_chain);
+		return ret;
+	}
+
+	tqp_type_and_id = le16_to_cpu(data->tqp_type_and_id[0]);
+	int_gl_index = hnae3_get_field(tqp_type_and_id,
+				       HCLGE_INT_GL_IDX_M, HCLGE_INT_GL_IDX_S);
+
+	resp->data[HCLGE_RING_TYPE_OFFSET] = req->msg.param[0].ring_type;
+	resp->data[HCLGE_TQP_INDEX_OFFSET] = req->msg.param[0].tqp_index;
+	resp->data[HCLGE_INT_GL_INDEX_OFFSET] = int_gl_index;
+	resp->data[HCLGE_VECTOR_ID_OFFSET] = data->int_vector_id_l;
+	resp->len = HCLGE_RING_VECTOR_MAP_INFO_LEN;
+
+	hclge_free_vector_ring_chain(&ring_chain);
+
+	return ret;
+}
+
 static void hclge_set_vf_promisc_mode(struct hclge_vport *vport,
 				      struct hclge_mbx_vf_to_pf_cmd *req)
 {
@@ -331,16 +415,14 @@
 				      u16 state,
 				      struct hclge_vlan_info *vlan_info)
 {
-#define MSG_DATA_SIZE	8
-
-	u8 msg_data[MSG_DATA_SIZE];
+	struct hclge_mbx_port_base_vlan base_vlan;
 
-	memcpy(&msg_data[0], &state, sizeof(u16));
-	memcpy(&msg_data[2], &vlan_info->vlan_proto, sizeof(u16));
-	memcpy(&msg_data[4], &vlan_info->qos, sizeof(u16));
-	memcpy(&msg_data[6], &vlan_info->vlan_tag, sizeof(u16));
+	base_vlan.state = cpu_to_le16(state);
+	base_vlan.vlan_proto = cpu_to_le16(vlan_info->vlan_proto);
+	base_vlan.qos = cpu_to_le16(vlan_info->qos);
+	base_vlan.vlan_tag = cpu_to_le16(vlan_info->vlan_tag);
 
-	return hclge_send_mbx_msg(vport, msg_data, sizeof(msg_data),
+	return hclge_send_mbx_msg(vport, (u8 *)&base_vlan, sizeof(base_vlan),
 				  HCLGE_MBX_PUSH_VLAN_INFO, vfid);
 }
 
@@ -480,10 +562,9 @@
 #define HCLGE_VF_LINK_STATE_UP		1U
 #define HCLGE_VF_LINK_STATE_DOWN	0U
 
+	struct hclge_mbx_link_status link_info;
 	struct hclge_dev *hdev = vport->back;
 	u16 link_status;
-	u8 msg_data[9];
-	u16 duplex;
 
 	/* mac.link can only be 0 or 1 */
 	switch (vport->vf_info.link_state) {
@@ -499,14 +580,13 @@
 		break;
 	}
 
-	duplex = hdev->hw.mac.duplex;
-	memcpy(&msg_data[0], &link_status, sizeof(u16));
-	memcpy(&msg_data[2], &hdev->hw.mac.speed, sizeof(u32));
-	memcpy(&msg_data[6], &duplex, sizeof(u16));
-	msg_data[8] = HCLGE_MBX_PUSH_LINK_STATUS_EN;
+	link_info.link_status = cpu_to_le16(link_status);
+	link_info.speed = cpu_to_le32(hdev->hw.mac.speed);
+	link_info.duplex = cpu_to_le16(hdev->hw.mac.duplex);
+	link_info.flag = HCLGE_MBX_PUSH_LINK_STATUS_EN;
 
 	/* send this requested info to VF */
-	return hclge_send_mbx_msg(vport, msg_data, sizeof(msg_data),
+	return hclge_send_mbx_msg(vport, (u8 *)&link_info, sizeof(link_info),
 				  HCLGE_MBX_LINK_STAT_CHANGE, vport->vport_id);
 }
 
@@ -514,22 +594,22 @@
 				struct hclge_mbx_vf_to_pf_cmd *mbx_req)
 {
 #define HCLGE_SUPPORTED   1
+	struct hclge_mbx_link_mode link_mode;
 	struct hclge_dev *hdev = vport->back;
 	unsigned long advertising;
 	unsigned long supported;
 	unsigned long send_data;
-	u8 msg_data[10] = {};
 	u8 dest_vfid;
 
 	advertising = hdev->hw.mac.advertising[0];
 	supported = hdev->hw.mac.supported[0];
 	dest_vfid = mbx_req->mbx_src_vfid;
-	msg_data[0] = mbx_req->msg.data[0];
+	send_data = mbx_req->msg.data[0] == HCLGE_SUPPORTED ? supported :
+							      advertising;
+	link_mode.idx = cpu_to_le16((u16)mbx_req->msg.data[0]);
+	link_mode.link_mode = cpu_to_le64(send_data);
 
-	send_data = msg_data[0] == HCLGE_SUPPORTED ? supported : advertising;
-
-	memcpy(&msg_data[2], &send_data, sizeof(unsigned long));
-	hclge_send_mbx_msg(vport, msg_data, sizeof(msg_data),
+	hclge_send_mbx_msg(vport, (u8 *)&link_mode, sizeof(link_mode),
 			   HCLGE_MBX_LINK_STAT_MODE, dest_vfid);
 }
 
@@ -586,9 +666,9 @@
 	return hclge_set_vport_mtu(vport, mtu);
 }
 
-static void hclge_get_queue_id_in_pf(struct hclge_vport *vport,
-				     struct hclge_mbx_vf_to_pf_cmd *mbx_req,
-				     struct hclge_respond_to_vf_msg *resp_msg)
+static int hclge_get_queue_id_in_pf(struct hclge_vport *vport,
+				    struct hclge_mbx_vf_to_pf_cmd *mbx_req,
+				    struct hclge_respond_to_vf_msg *resp_msg)
 {
 	struct hnae3_handle *handle = &vport->nic;
 	struct hclge_dev *hdev = vport->back;
@@ -598,17 +678,18 @@
 	if (queue_id >= handle->kinfo.num_tqps) {
 		dev_err(&hdev->pdev->dev, "Invalid queue id(%u) from VF %u\n",
 			queue_id, mbx_req->mbx_src_vfid);
-		return;
+		return -EINVAL;
 	}
 
 	qid_in_pf = hclge_covert_handle_qid_global(&vport->nic, queue_id);
 	memcpy(resp_msg->data, &qid_in_pf, sizeof(qid_in_pf));
 	resp_msg->len = sizeof(qid_in_pf);
+	return 0;
 }
 
-static void hclge_get_rss_key(struct hclge_vport *vport,
-			      struct hclge_mbx_vf_to_pf_cmd *mbx_req,
-			      struct hclge_respond_to_vf_msg *resp_msg)
+static int hclge_get_rss_key(struct hclge_vport *vport,
+			     struct hclge_mbx_vf_to_pf_cmd *mbx_req,
+			     struct hclge_respond_to_vf_msg *resp_msg)
 {
 #define HCLGE_RSS_MBX_RESP_LEN	8
 	struct hclge_dev *hdev = vport->back;
@@ -624,13 +705,14 @@
 		dev_warn(&hdev->pdev->dev,
 			 "failed to get the rss hash key, the index(%u) invalid !\n",
 			 index);
-		return;
+		return -EINVAL;
 	}
 
 	memcpy(resp_msg->data,
 	       &hdev->vport[0].rss_hash_key[index * HCLGE_RSS_MBX_RESP_LEN],
 	       HCLGE_RSS_MBX_RESP_LEN);
 	resp_msg->len = HCLGE_RSS_MBX_RESP_LEN;
+	return 0;
 }
 
 static void hclge_link_fail_parse(struct hclge_dev *hdev, u8 link_fail_code)
@@ -663,7 +745,7 @@
 {
 	u32 tail = hclge_read_dev(hw, HCLGE_NIC_CRQ_TAIL_REG);
 
-	return tail == hw->cmq.crq.next_to_use;
+	return tail == hw->hw.cmq.crq.next_to_use;
 }
 
 static void hclge_handle_ncsi_error(struct hclge_dev *hdev)
@@ -692,20 +774,289 @@
 	}
 }
 
+static int
+hclge_mbx_map_ring_to_vector_handler(struct hclge_mbx_ops_param *param)
+{
+	return hclge_map_unmap_ring_to_vf_vector(param->vport, true,
+						 param->req);
+}
+
+static int
+hclge_mbx_unmap_ring_to_vector_handler(struct hclge_mbx_ops_param *param)
+{
+	return hclge_map_unmap_ring_to_vf_vector(param->vport, false,
+						 param->req);
+}
+
+static int
+hclge_mbx_get_ring_vector_map_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_get_vf_ring_vector_map(param->vport, param->req,
+					   param->resp_msg);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"PF fail(%d) to get VF ring vector map\n",
+			ret);
+	return ret;
+}
+
+static int hclge_mbx_set_promisc_mode_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_set_vf_promisc_mode(param->vport, param->req);
+	return 0;
+}
+
+static int hclge_mbx_set_unicast_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_set_vf_uc_mac_addr(param->vport, param->req);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"PF fail(%d) to set VF UC MAC Addr\n",
+			ret);
+	return ret;
+}
+
+static int hclge_mbx_set_multicast_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_set_vf_mc_mac_addr(param->vport, param->req);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"PF fail(%d) to set VF MC MAC Addr\n",
+			ret);
+	return ret;
+}
+
+static int hclge_mbx_set_vlan_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_set_vf_vlan_cfg(param->vport, param->req, param->resp_msg);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"PF failed(%d) to config VF's VLAN\n",
+			ret);
+	return ret;
+}
+
+static int hclge_mbx_set_alive_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_set_vf_alive(param->vport, param->req);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"PF failed(%d) to set VF's ALIVE\n",
+			ret);
+	return ret;
+}
+
+static int hclge_mbx_get_qinfo_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_get_vf_queue_info(param->vport, param->resp_msg);
+	return 0;
+}
+
+static int hclge_mbx_get_qdepth_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_get_vf_queue_depth(param->vport, param->resp_msg);
+	return 0;
+}
+
+static int hclge_mbx_get_basic_info_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_get_basic_info(param->vport, param->resp_msg);
+	return 0;
+}
+
+static int hclge_mbx_get_link_status_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_push_vf_link_status(param->vport);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"failed to inform link stat to VF, ret = %d\n",
+			ret);
+	return ret;
+}
+
+static int hclge_mbx_queue_reset_handler(struct hclge_mbx_ops_param *param)
+{
+	return hclge_mbx_reset_vf_queue(param->vport, param->req,
+					param->resp_msg);
+}
+
+static int hclge_mbx_reset_handler(struct hclge_mbx_ops_param *param)
+{
+	return hclge_reset_vf(param->vport);
+}
+
+static int hclge_mbx_keep_alive_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_vf_keep_alive(param->vport);
+	return 0;
+}
+
+static int hclge_mbx_set_mtu_handler(struct hclge_mbx_ops_param *param)
+{
+	int ret;
+
+	ret = hclge_set_vf_mtu(param->vport, param->req);
+	if (ret)
+		dev_err(&param->vport->back->pdev->dev,
+			"VF fail(%d) to set mtu\n", ret);
+	return ret;
+}
+
+static int hclge_mbx_get_qid_in_pf_handler(struct hclge_mbx_ops_param *param)
+{
+	return hclge_get_queue_id_in_pf(param->vport, param->req,
+					param->resp_msg);
+}
+
+static int hclge_mbx_get_rss_key_handler(struct hclge_mbx_ops_param *param)
+{
+	return hclge_get_rss_key(param->vport, param->req, param->resp_msg);
+}
+
+static int hclge_mbx_get_link_mode_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_get_link_mode(param->vport, param->req);
+	return 0;
+}
+
+static int
+hclge_mbx_get_vf_flr_status_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_rm_vport_all_mac_table(param->vport, false,
+				     HCLGE_MAC_ADDR_UC);
+	hclge_rm_vport_all_mac_table(param->vport, false,
+				     HCLGE_MAC_ADDR_MC);
+	hclge_rm_vport_all_vlan_table(param->vport, false);
+	return 0;
+}
+
+static int hclge_mbx_vf_uninit_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_rm_vport_all_mac_table(param->vport, true,
+				     HCLGE_MAC_ADDR_UC);
+	hclge_rm_vport_all_mac_table(param->vport, true,
+				     HCLGE_MAC_ADDR_MC);
+	hclge_rm_vport_all_vlan_table(param->vport, true);
+	return 0;
+}
+
+static int hclge_mbx_get_media_type_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_get_vf_media_type(param->vport, param->resp_msg);
+	return 0;
+}
+
+static int hclge_mbx_push_link_status_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_handle_link_change_event(param->vport->back, param->req);
+	return 0;
+}
+
+static int hclge_mbx_get_mac_addr_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_get_vf_mac_addr(param->vport, param->resp_msg);
+	return 0;
+}
+
+static int hclge_mbx_ncsi_error_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_handle_ncsi_error(param->vport->back);
+	return 0;
+}
+
+static int hclge_mbx_handle_vf_tbl_handler(struct hclge_mbx_ops_param *param)
+{
+	hclge_handle_vf_tbl(param->vport, param->req);
+	return 0;
+}
+
+static const hclge_mbx_ops_fn hclge_mbx_ops_list[HCLGE_MBX_OPCODE_MAX] = {
+	[HCLGE_MBX_RESET]   = hclge_mbx_reset_handler,
+	[HCLGE_MBX_SET_UNICAST] = hclge_mbx_set_unicast_handler,
+	[HCLGE_MBX_SET_MULTICAST] = hclge_mbx_set_multicast_handler,
+	[HCLGE_MBX_SET_VLAN] = hclge_mbx_set_vlan_handler,
+	[HCLGE_MBX_MAP_RING_TO_VECTOR] = hclge_mbx_map_ring_to_vector_handler,
+	[HCLGE_MBX_UNMAP_RING_TO_VECTOR] = hclge_mbx_unmap_ring_to_vector_handler,
+	[HCLGE_MBX_SET_PROMISC_MODE] = hclge_mbx_set_promisc_mode_handler,
+	[HCLGE_MBX_GET_QINFO] = hclge_mbx_get_qinfo_handler,
+	[HCLGE_MBX_GET_QDEPTH] = hclge_mbx_get_qdepth_handler,
+	[HCLGE_MBX_GET_BASIC_INFO] = hclge_mbx_get_basic_info_handler,
+	[HCLGE_MBX_GET_RSS_KEY] = hclge_mbx_get_rss_key_handler,
+	[HCLGE_MBX_GET_MAC_ADDR] = hclge_mbx_get_mac_addr_handler,
+	[HCLGE_MBX_GET_LINK_STATUS] = hclge_mbx_get_link_status_handler,
+	[HCLGE_MBX_QUEUE_RESET] = hclge_mbx_queue_reset_handler,
+	[HCLGE_MBX_KEEP_ALIVE] = hclge_mbx_keep_alive_handler,
+	[HCLGE_MBX_SET_ALIVE] = hclge_mbx_set_alive_handler,
+	[HCLGE_MBX_SET_MTU] = hclge_mbx_set_mtu_handler,
+	[HCLGE_MBX_GET_QID_IN_PF] = hclge_mbx_get_qid_in_pf_handler,
+	[HCLGE_MBX_GET_LINK_MODE] = hclge_mbx_get_link_mode_handler,
+	[HCLGE_MBX_GET_MEDIA_TYPE] = hclge_mbx_get_media_type_handler,
+	[HCLGE_MBX_VF_UNINIT] = hclge_mbx_vf_uninit_handler,
+	[HCLGE_MBX_HANDLE_VF_TBL] = hclge_mbx_handle_vf_tbl_handler,
+	[HCLGE_MBX_GET_RING_VECTOR_MAP] = hclge_mbx_get_ring_vector_map_handler,
+	[HCLGE_MBX_GET_VF_FLR_STATUS] = hclge_mbx_get_vf_flr_status_handler,
+	[HCLGE_MBX_PUSH_LINK_STATUS] = hclge_mbx_push_link_status_handler,
+	[HCLGE_MBX_NCSI_ERROR] = hclge_mbx_ncsi_error_handler,
+};
+
+static void hclge_mbx_request_handling(struct hclge_mbx_ops_param *param)
+{
+	hclge_mbx_ops_fn cmd_func = NULL;
+	struct hclge_dev *hdev;
+	int ret = 0;
+
+	hdev = param->vport->back;
+	cmd_func = hclge_mbx_ops_list[param->req->msg.code];
+	if (!cmd_func) {
+		dev_err(&hdev->pdev->dev,
+			"un-supported mailbox message, code = %u\n",
+			param->req->msg.code);
+		return;
+	}
+	ret = cmd_func(param);
+
+	/* PF driver should not reply IMP */
+	if (hnae3_get_bit(param->req->mbx_need_resp, HCLGE_MBX_NEED_RESP_B) &&
+	    param->req->msg.code < HCLGE_MBX_GET_VF_FLR_STATUS) {
+		param->resp_msg->status = ret;
+		if (time_is_before_jiffies(hdev->last_mbx_scheduled +
+					   HCLGE_MBX_SCHED_TIMEOUT))
+			dev_warn(&hdev->pdev->dev,
+				 "resp vport%u mbx(%u,%u) late\n",
+				 param->req->mbx_src_vfid,
+				 param->req->msg.code,
+				 param->req->msg.subcode);
+
+		hclge_gen_resp_to_vf(param->vport, param->req, param->resp_msg);
+	}
+}
+
 void hclge_mbx_handler(struct hclge_dev *hdev)
 {
-	struct hclge_cmq_ring *crq = &hdev->hw.cmq.crq;
+	struct hclge_comm_cmq_ring *crq = &hdev->hw.hw.cmq.crq;
 	struct hclge_respond_to_vf_msg resp_msg;
 	struct hclge_mbx_vf_to_pf_cmd *req;
-	struct hclge_vport *vport;
+	struct hclge_mbx_ops_param param;
 	struct hclge_desc *desc;
-	bool is_del = false;
 	unsigned int flag;
-	int ret = 0;
 
+	param.resp_msg = &resp_msg;
 	/* handle all the mailbox requests in the queue */
 	while (!hclge_cmd_crq_empty(&hdev->hw)) {
-		if (test_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state)) {
+		if (test_bit(HCLGE_COMM_STATE_CMD_DISABLE,
+			     &hdev->hw.hw.comm_state)) {
 			dev_warn(&hdev->pdev->dev,
 				 "command queue needs re-initializing\n");
 			return;
@@ -715,10 +1066,11 @@
 		req = (struct hclge_mbx_vf_to_pf_cmd *)desc->data;
 
 		flag = le16_to_cpu(crq->desc[crq->next_to_use].flag);
-		if (unlikely(!hnae3_get_bit(flag, HCLGE_CMDQ_RX_OUTVLD_B))) {
+		if (unlikely(!hnae3_get_bit(flag, HCLGE_CMDQ_RX_OUTVLD_B) ||
+			     req->mbx_src_vfid > hdev->num_req_vfs)) {
 			dev_warn(&hdev->pdev->dev,
-				 "dropped invalid mailbox message, code = %u\n",
-				 req->msg.code);
+				 "dropped invalid mailbox message, code = %u, vfid = %u\n",
+				 req->msg.code, req->mbx_src_vfid);
 
 			/* dropping/not processing this invalid message */
 			crq->desc[crq->next_to_use].flag = 0;
@@ -726,136 +1078,16 @@
 			continue;
 		}
 
-		vport = &hdev->vport[req->mbx_src_vfid];
-
 		trace_hclge_pf_mbx_get(hdev, req);
 
 		/* clear the resp_msg before processing every mailbox message */
 		memset(&resp_msg, 0, sizeof(resp_msg));
-
-		switch (req->msg.code) {
-		case HCLGE_MBX_MAP_RING_TO_VECTOR:
-			ret = hclge_map_unmap_ring_to_vf_vector(vport, true,
-								req);
-			break;
-		case HCLGE_MBX_UNMAP_RING_TO_VECTOR:
-			ret = hclge_map_unmap_ring_to_vf_vector(vport, false,
-								req);
-			break;
-		case HCLGE_MBX_SET_PROMISC_MODE:
-			hclge_set_vf_promisc_mode(vport, req);
-			break;
-		case HCLGE_MBX_SET_UNICAST:
-			ret = hclge_set_vf_uc_mac_addr(vport, req);
-			if (ret)
-				dev_err(&hdev->pdev->dev,
-					"PF fail(%d) to set VF UC MAC Addr\n",
-					ret);
-			break;
-		case HCLGE_MBX_SET_MULTICAST:
-			ret = hclge_set_vf_mc_mac_addr(vport, req);
-			if (ret)
-				dev_err(&hdev->pdev->dev,
-					"PF fail(%d) to set VF MC MAC Addr\n",
-					ret);
-			break;
-		case HCLGE_MBX_SET_VLAN:
-			ret = hclge_set_vf_vlan_cfg(vport, req, &resp_msg);
-			if (ret)
-				dev_err(&hdev->pdev->dev,
-					"PF failed(%d) to config VF's VLAN\n",
-					ret);
-			break;
-		case HCLGE_MBX_SET_ALIVE:
-			ret = hclge_set_vf_alive(vport, req);
-			if (ret)
-				dev_err(&hdev->pdev->dev,
-					"PF failed(%d) to set VF's ALIVE\n",
-					ret);
-			break;
-		case HCLGE_MBX_GET_QINFO:
-			hclge_get_vf_queue_info(vport, &resp_msg);
-			break;
-		case HCLGE_MBX_GET_QDEPTH:
-			hclge_get_vf_queue_depth(vport, &resp_msg);
-			break;
-		case HCLGE_MBX_GET_BASIC_INFO:
-			hclge_get_basic_info(vport, &resp_msg);
-			break;
-		case HCLGE_MBX_GET_LINK_STATUS:
-			ret = hclge_push_vf_link_status(vport);
-			if (ret)
-				dev_err(&hdev->pdev->dev,
-					"failed to inform link stat to VF, ret = %d\n",
-					ret);
-			break;
-		case HCLGE_MBX_QUEUE_RESET:
-			ret = hclge_mbx_reset_vf_queue(vport, req, &resp_msg);
-			break;
-		case HCLGE_MBX_RESET:
-			ret = hclge_reset_vf(vport);
-			break;
-		case HCLGE_MBX_KEEP_ALIVE:
-			hclge_vf_keep_alive(vport);
-			break;
-		case HCLGE_MBX_SET_MTU:
-			ret = hclge_set_vf_mtu(vport, req);
-			if (ret)
-				dev_err(&hdev->pdev->dev,
-					"VF fail(%d) to set mtu\n", ret);
-			break;
-		case HCLGE_MBX_GET_QID_IN_PF:
-			hclge_get_queue_id_in_pf(vport, req, &resp_msg);
-			break;
-		case HCLGE_MBX_GET_RSS_KEY:
-			hclge_get_rss_key(vport, req, &resp_msg);
-			break;
-		case HCLGE_MBX_GET_LINK_MODE:
-			hclge_get_link_mode(vport, req);
-			break;
-		case HCLGE_MBX_GET_VF_FLR_STATUS:
-		case HCLGE_MBX_VF_UNINIT:
-			is_del = req->msg.code == HCLGE_MBX_VF_UNINIT;
-			hclge_rm_vport_all_mac_table(vport, is_del,
-						     HCLGE_MAC_ADDR_UC);
-			hclge_rm_vport_all_mac_table(vport, is_del,
-						     HCLGE_MAC_ADDR_MC);
-			hclge_rm_vport_all_vlan_table(vport, is_del);
-			break;
-		case HCLGE_MBX_GET_MEDIA_TYPE:
-			hclge_get_vf_media_type(vport, &resp_msg);
-			break;
-		case HCLGE_MBX_PUSH_LINK_STATUS:
-			hclge_handle_link_change_event(hdev, req);
-			break;
-		case HCLGE_MBX_GET_MAC_ADDR:
-			hclge_get_vf_mac_addr(vport, &resp_msg);
-			break;
-		case HCLGE_MBX_NCSI_ERROR:
-			hclge_handle_ncsi_error(hdev);
-			break;
-		case HCLGE_MBX_HANDLE_VF_TBL:
-			hclge_handle_vf_tbl(vport, req);
-			break;
-		default:
-			dev_err(&hdev->pdev->dev,
-				"un-supported mailbox message, code = %u\n",
-				req->msg.code);
-			break;
-		}
-
-		/* PF driver should not reply IMP */
-		if (hnae3_get_bit(req->mbx_need_resp, HCLGE_MBX_NEED_RESP_B) &&
-		    req->msg.code < HCLGE_MBX_GET_VF_FLR_STATUS) {
-			resp_msg.status = ret;
-			hclge_gen_resp_to_vf(vport, req, &resp_msg);
-		}
+		param.vport = &hdev->vport[req->mbx_src_vfid];
+		param.req = req;
+		hclge_mbx_request_handling(&param);
 
 		crq->desc[crq->next_to_use].flag = 0;
 		hclge_mbx_ring_ptr_move_crq(crq);
-
-		/* reinitialize ret after complete the mbx message processing */
-		ret = 0;
 	}
 
 	/* Write back CMDQ_RQ header pointer, M7 need this pointer */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c
@@ -47,7 +47,7 @@
 	struct hclge_desc desc;
 	int ret;
 
-	if (test_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state))
+	if (test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state))
 		return 0;
 
 	hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, false);
@@ -85,7 +85,7 @@
 	struct hclge_desc desc;
 	int ret;
 
-	if (test_bit(HCLGE_STATE_CMD_DISABLE, &hdev->state))
+	if (test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state))
 		return 0;
 
 	hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, true);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_ptp.c
@@ -120,7 +120,7 @@
 	u64 ns = nsec;
 	u32 sec_h;
 
-	if (!test_bit(HCLGE_PTP_FLAG_RX_EN, &hdev->ptp->flags))
+	if (!hdev->ptp || !test_bit(HCLGE_PTP_FLAG_RX_EN, &hdev->ptp->flags))
 		return;
 
 	/* Since the BD does not have enough space for the higher 16 bits of
@@ -464,7 +464,7 @@
 	}
 
 	spin_lock_init(&ptp->lock);
-	ptp->io_base = hdev->hw.io_base + HCLGE_PTP_REG_OFFSET;
+	ptp->io_base = hdev->hw.hw.io_base + HCLGE_PTP_REG_OFFSET;
 	ptp->ts_cfg.rx_filter = HWTSTAMP_FILTER_NONE;
 	ptp->ts_cfg.tx_type = HWTSTAMP_TX_OFF;
 	hdev->ptp = ptp;
@@ -496,7 +496,7 @@
 
 		ret = hclge_ptp_get_cycle(hdev);
 		if (ret)
-			return ret;
+			goto out;
 	}
 
 	ret = hclge_ptp_int_en(hdev, true);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c
@@ -113,50 +113,50 @@
 	return 0;
 }
 
-static int hclge_pfc_stats_get(struct hclge_dev *hdev,
-			       enum hclge_opcode_type opcode, u64 *stats)
-{
-	struct hclge_desc desc[HCLGE_TM_PFC_PKT_GET_CMD_NUM];
-	int ret, i, j;
-
-	if (!(opcode == HCLGE_OPC_QUERY_PFC_RX_PKT_CNT ||
-	      opcode == HCLGE_OPC_QUERY_PFC_TX_PKT_CNT))
-		return -EINVAL;
-
-	for (i = 0; i < HCLGE_TM_PFC_PKT_GET_CMD_NUM - 1; i++) {
-		hclge_cmd_setup_basic_desc(&desc[i], opcode, true);
-		desc[i].flag |= cpu_to_le16(HCLGE_CMD_FLAG_NEXT);
-	}
+static const u16 hclge_pfc_tx_stats_offset[] = {
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri0_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri1_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri2_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri3_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri4_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri5_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri6_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_tx_pfc_pri7_pkt_num)
+};
+
+static const u16 hclge_pfc_rx_stats_offset[] = {
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri0_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri1_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri2_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri3_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri4_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri5_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri6_pkt_num),
+	HCLGE_MAC_STATS_FIELD_OFF(mac_rx_pfc_pri7_pkt_num)
+};
 
-	hclge_cmd_setup_basic_desc(&desc[i], opcode, true);
+static void hclge_pfc_stats_get(struct hclge_dev *hdev, bool tx, u64 *stats)
+{
+	const u16 *offset;
+	int i;
 
-	ret = hclge_cmd_send(&hdev->hw, desc, HCLGE_TM_PFC_PKT_GET_CMD_NUM);
-	if (ret)
-		return ret;
+	if (tx)
+		offset = hclge_pfc_tx_stats_offset;
+	else
+		offset = hclge_pfc_rx_stats_offset;
 
-	for (i = 0; i < HCLGE_TM_PFC_PKT_GET_CMD_NUM; i++) {
-		struct hclge_pfc_stats_cmd *pfc_stats =
-				(struct hclge_pfc_stats_cmd *)desc[i].data;
-
-		for (j = 0; j < HCLGE_TM_PFC_NUM_GET_PER_CMD; j++) {
-			u32 index = i * HCLGE_TM_PFC_PKT_GET_CMD_NUM + j;
-
-			if (index < HCLGE_MAX_TC_NUM)
-				stats[index] =
-					le64_to_cpu(pfc_stats->pkt_num[j]);
-		}
-	}
-	return 0;
+	for (i = 0; i < HCLGE_MAX_TC_NUM; i++)
+		stats[i] = HCLGE_STATS_READ(&hdev->mac_stats, offset[i]);
 }
 
-int hclge_pfc_rx_stats_get(struct hclge_dev *hdev, u64 *stats)
+void hclge_pfc_rx_stats_get(struct hclge_dev *hdev, u64 *stats)
 {
-	return hclge_pfc_stats_get(hdev, HCLGE_OPC_QUERY_PFC_RX_PKT_CNT, stats);
+	hclge_pfc_stats_get(hdev, false, stats);
 }
 
-int hclge_pfc_tx_stats_get(struct hclge_dev *hdev, u64 *stats)
+void hclge_pfc_tx_stats_get(struct hclge_dev *hdev, u64 *stats)
 {
-	return hclge_pfc_stats_get(hdev, HCLGE_OPC_QUERY_PFC_TX_PKT_CNT, stats);
+	hclge_pfc_stats_get(hdev, true, stats);
 }
 
 int hclge_mac_pause_en_cfg(struct hclge_dev *hdev, bool tx, bool rx)
@@ -171,8 +171,8 @@
 	return hclge_cmd_send(&hdev->hw, &desc, 1);
 }
 
-static int hclge_pfc_pause_en_cfg(struct hclge_dev *hdev, u8 tx_rx_bitmap,
-				  u8 pfc_bitmap)
+int hclge_pfc_pause_en_cfg(struct hclge_dev *hdev, u8 tx_rx_bitmap,
+			   u8 pfc_bitmap)
 {
 	struct hclge_desc desc;
 	struct hclge_pfc_en_cmd *pfc = (struct hclge_pfc_en_cmd *)desc.data;
@@ -420,7 +420,7 @@
 	return hclge_cmd_send(&hdev->hw, &desc, 1);
 }
 
-static int hclge_tm_port_shaper_cfg(struct hclge_dev *hdev)
+int hclge_tm_port_shaper_cfg(struct hclge_dev *hdev)
 {
 	struct hclge_port_shapping_cmd *shap_cfg_cmd;
 	struct hclge_shaper_ir_para ir_para;
@@ -732,6 +732,7 @@
 static void hclge_tm_pg_info_init(struct hclge_dev *hdev)
 {
 #define BW_PERCENT	100
+#define DEFAULT_BW_WEIGHT	1
 
 	u8 i;
 
@@ -753,7 +754,7 @@
 		for (k = 0; k < hdev->tm_info.num_tc; k++)
 			hdev->tm_info.pg_info[i].tc_dwrr[k] = BW_PERCENT;
 		for (; k < HNAE3_MAX_TC; k++)
-			hdev->tm_info.pg_info[i].tc_dwrr[k] = 0;
+			hdev->tm_info.pg_info[i].tc_dwrr[k] = DEFAULT_BW_WEIGHT;
 	}
 }
 
@@ -1123,7 +1124,6 @@
 
 static int hclge_tm_ets_tc_dwrr_cfg(struct hclge_dev *hdev)
 {
-#define DEFAULT_TC_WEIGHT	1
 #define DEFAULT_TC_OFFSET	14
 
 	struct hclge_ets_tc_weight_cmd *ets_weight;
@@ -1136,13 +1136,7 @@
 	for (i = 0; i < HNAE3_MAX_TC; i++) {
 		struct hclge_pg_info *pg_info;
 
-		ets_weight->tc_weight[i] = DEFAULT_TC_WEIGHT;
-
-		if (!(hdev->hw_tc_map & BIT(i)))
-			continue;
-
-		pg_info =
-			&hdev->tm_info.pg_info[hdev->tm_info.tc_info[i].pgid];
+		pg_info = &hdev->tm_info.pg_info[hdev->tm_info.tc_info[i].pgid];
 		ets_weight->tc_weight[i] = pg_info->tc_dwrr[i];
 	}
 
@@ -1435,7 +1429,7 @@
 	return 0;
 }
 
-static int hclge_mac_pause_setup_hw(struct hclge_dev *hdev)
+int hclge_mac_pause_setup_hw(struct hclge_dev *hdev)
 {
 	bool tx_en, rx_en;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h
@@ -155,6 +155,9 @@
 	u32 rsvd1;
 };
 
+#define HCLGE_PFC_DISABLE	0
+#define HCLGE_PFC_TX_RX_DISABLE	0
+
 struct hclge_pfc_en_cmd {
 	u8 tx_rx_en_bitmap;
 	u8 pri_en_bitmap;
@@ -226,11 +229,15 @@
 void hclge_tm_pfc_info_update(struct hclge_dev *hdev);
 int hclge_tm_dwrr_cfg(struct hclge_dev *hdev);
 int hclge_tm_init_hw(struct hclge_dev *hdev, bool init);
+int hclge_pfc_pause_en_cfg(struct hclge_dev *hdev, u8 tx_rx_bitmap,
+			   u8 pfc_bitmap);
 int hclge_mac_pause_en_cfg(struct hclge_dev *hdev, bool tx, bool rx);
 int hclge_pause_addr_cfg(struct hclge_dev *hdev, const u8 *mac_addr);
-int hclge_pfc_rx_stats_get(struct hclge_dev *hdev, u64 *stats);
-int hclge_pfc_tx_stats_get(struct hclge_dev *hdev, u64 *stats);
+int hclge_mac_pause_setup_hw(struct hclge_dev *hdev);
+void hclge_pfc_rx_stats_get(struct hclge_dev *hdev, u64 *stats);
+void hclge_pfc_tx_stats_get(struct hclge_dev *hdev, u64 *stats);
 int hclge_tm_qs_shaper_cfg(struct hclge_vport *vport, int max_tx_rate);
+int hclge_tm_port_shaper_cfg(struct hclge_dev *hdev);
 int hclge_tm_get_qset_num(struct hclge_dev *hdev, u16 *qset_num);
 int hclge_tm_get_pri_num(struct hclge_dev *hdev, u8 *pri_num);
 int hclge_tm_get_qset_map_pri(struct hclge_dev *hdev, u16 qset_id, u8 *priority,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_trace.h
@@ -24,7 +24,7 @@
 		__field(u8, code)
 		__field(u8, subcode)
 		__string(pciname, pci_name(hdev->pdev))
-		__string(devname, &hdev->vport[0].nic.kinfo.netdev->name)
+		__string(devname, hdev->vport[0].nic.kinfo.netdev->name)
 		__array(u32, mbx_data, PF_GET_MBX_LEN)
 	),
 
@@ -33,7 +33,7 @@
 		__entry->code = req->msg.code;
 		__entry->subcode = req->msg.subcode;
 		__assign_str(pciname, pci_name(hdev->pdev));
-		__assign_str(devname, &hdev->vport[0].nic.kinfo.netdev->name);
+		__assign_str(devname, hdev->vport[0].nic.kinfo.netdev->name);
 		memcpy(__entry->mbx_data, req,
 		       sizeof(struct hclge_mbx_vf_to_pf_cmd));
 	),
@@ -56,15 +56,15 @@
 		__field(u8, vfid)
 		__field(u16, code)
 		__string(pciname, pci_name(hdev->pdev))
-		__string(devname, &hdev->vport[0].nic.kinfo.netdev->name)
+		__string(devname, hdev->vport[0].nic.kinfo.netdev->name)
 		__array(u32, mbx_data, PF_SEND_MBX_LEN)
 	),
 
 	TP_fast_assign(
 		__entry->vfid = req->dest_vfid;
-		__entry->code = req->msg.code;
+		__entry->code = le16_to_cpu(req->msg.code);
 		__assign_str(pciname, pci_name(hdev->pdev));
-		__assign_str(devname, &hdev->vport[0].nic.kinfo.netdev->name);
+		__assign_str(devname, hdev->vport[0].nic.kinfo.netdev->name);
 		memcpy(__entry->mbx_data, req,
 		       sizeof(struct hclge_mbx_pf_to_vf_cmd));
 	),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c
@@ -537,7 +537,8 @@
 
 	nic->ae_algo = &ae_algovf;
 	nic->pdev = hdev->pdev;
-	nic->numa_node_mask = hdev->numa_node_mask;
+	bitmap_copy(nic->numa_node_mask.bits, hdev->numa_node_mask.bits,
+		    MAX_NUMNODES);
 	nic->flags |= HNAE3_SUPPORT_VF;
 	nic->kinfo.io_base = hdev->hw.io_base;
 
@@ -703,9 +704,9 @@
 	roundup_size = ilog2(roundup_size);
 
 	for (i = 0; i < HCLGEVF_MAX_TC_NUM; i++) {
-		tc_valid[i] = !!(hdev->hw_tc_map & BIT(i));
+		tc_valid[i] = 1;
 		tc_size[i] = roundup_size;
-		tc_offset[i] = rss_size * i;
+		tc_offset[i] = (hdev->hw_tc_map & BIT(i)) ? rss_size * i : 0;
 	}
 
 	hclgevf_cmd_setup_basic_desc(&desc, HCLGEVF_OPC_RSS_TC_MODE, false);
@@ -1349,7 +1350,7 @@
 		ether_addr_copy(p, hdev->hw.mac.mac_addr);
 }
 
-static int hclgevf_set_mac_addr(struct hnae3_handle *handle, void *p,
+static int hclgevf_set_mac_addr(struct hnae3_handle *handle, const void *p,
 				bool is_first)
 {
 	struct hclgevf_dev *hdev = hclgevf_ae_get_hdev(handle);
@@ -1514,15 +1515,18 @@
 				    struct list_head *list,
 				    enum HCLGEVF_MAC_ADDR_TYPE mac_type)
 {
+	char format_mac_addr[HNAE3_FORMAT_MAC_ADDR_LEN];
 	struct hclgevf_mac_addr_node *mac_node, *tmp;
 	int ret;
 
 	list_for_each_entry_safe(mac_node, tmp, list, node) {
 		ret = hclgevf_add_del_mac_addr(hdev, mac_node, mac_type);
 		if  (ret) {
+			hnae3_format_mac_addr(format_mac_addr,
+					      mac_node->mac_addr);
 			dev_err(&hdev->pdev->dev,
-				"failed to configure mac %pM, state = %d, ret = %d\n",
-				mac_node->mac_addr, mac_node->state, ret);
+				"failed to configure mac %s, state = %d, ret = %d\n",
+				format_mac_addr, mac_node->state, ret);
 			return;
 		}
 		if (mac_node->state == HCLGEVF_MAC_TO_ADD) {
@@ -1707,6 +1711,8 @@
 	     test_bit(HCLGEVF_STATE_RST_FAIL, &hdev->state)) && is_kill) {
 		set_bit(vlan_id, hdev->vlan_del_fail_bmap);
 		return -EBUSY;
+	} else if (!is_kill && test_bit(vlan_id, hdev->vlan_del_fail_bmap)) {
+		clear_bit(vlan_id, hdev->vlan_del_fail_bmap);
 	}
 
 	hclgevf_build_send_msg(&send_msg, HCLGE_MBX_SET_VLAN,
@@ -1734,20 +1740,25 @@
 	int ret, sync_cnt = 0;
 	u16 vlan_id;
 
+	if (bitmap_empty(hdev->vlan_del_fail_bmap, VLAN_N_VID))
+		return;
+
+	rtnl_lock();
 	vlan_id = find_first_bit(hdev->vlan_del_fail_bmap, VLAN_N_VID);
 	while (vlan_id != VLAN_N_VID) {
 		ret = hclgevf_set_vlan_filter(handle, htons(ETH_P_8021Q),
 					      vlan_id, true);
 		if (ret)
-			return;
+			break;
 
 		clear_bit(vlan_id, hdev->vlan_del_fail_bmap);
 		sync_cnt++;
 		if (sync_cnt >= HCLGEVF_MAX_SYNC_COUNT)
-			return;
+			break;
 
 		vlan_id = find_first_bit(hdev->vlan_del_fail_bmap, VLAN_N_VID);
 	}
+	rtnl_unlock();
 }
 
 static int hclgevf_en_hw_strip_rxvtag(struct hnae3_handle *handle, bool enable)
@@ -1882,7 +1893,10 @@
 	 * might happen in case reset assertion was made by PF. Yes, this also
 	 * means we might end up waiting bit more even for VF reset.
 	 */
-	msleep(5000);
+	if (hdev->reset_type == HNAE3_VF_FULL_RESET)
+		msleep(5000);
+	else
+		msleep(500);
 
 	return 0;
 }
@@ -2203,8 +2217,8 @@
 			 ret);
 
 	hdev->reset_type = HNAE3_NONE_RESET;
-	clear_bit(HCLGEVF_STATE_RST_HANDLING, &hdev->state);
-	up(&hdev->reset_sem);
+	if (test_and_clear_bit(HCLGEVF_STATE_RST_HANDLING, &hdev->state))
+		up(&hdev->reset_sem);
 }
 
 static u32 hclgevf_get_fw_version(struct hnae3_handle *handle)
@@ -2474,8 +2488,18 @@
 	return HCLGEVF_VECTOR0_EVENT_OTHER;
 }
 
+static void hclgevf_reset_timer(struct timer_list *t)
+{
+	struct hclgevf_dev *hdev = from_timer(hdev, t, reset_timer);
+
+	hclgevf_clear_event_cause(hdev, HCLGEVF_VECTOR0_EVENT_RST);
+	hclgevf_reset_task_schedule(hdev);
+}
+
 static irqreturn_t hclgevf_misc_irq_handle(int irq, void *data)
 {
+#define HCLGEVF_RESET_DELAY	5
+
 	enum hclgevf_evt_cause event_cause;
 	struct hclgevf_dev *hdev = data;
 	u32 clearval;
@@ -2487,7 +2511,8 @@
 
 	switch (event_cause) {
 	case HCLGEVF_VECTOR0_EVENT_RST:
-		hclgevf_reset_task_schedule(hdev);
+		mod_timer(&hdev->reset_timer,
+			  jiffies + msecs_to_jiffies(HCLGEVF_RESET_DELAY));
 		break;
 	case HCLGEVF_VECTOR0_EVENT_MBX:
 		hclgevf_mbx_handler(hdev);
@@ -2496,8 +2521,7 @@
 		break;
 	}
 
-	if (event_cause != HCLGEVF_VECTOR0_EVENT_OTHER)
-		hclgevf_enable_vector(&hdev->misc_vector, true);
+	hclgevf_enable_vector(&hdev->misc_vector, true);
 
 	return IRQ_HANDLED;
 }
@@ -2557,7 +2581,7 @@
 	    hdev->num_msi_left == 0)
 		return -EINVAL;
 
-	roce->rinfo.base_vector = hdev->roce_base_vector;
+	roce->rinfo.base_vector = hdev->roce_base_msix_offset;
 
 	roce->rinfo.netdev = nic->kinfo.netdev;
 	roce->rinfo.roce_io_base = hdev->hw.io_base;
@@ -2565,8 +2589,8 @@
 
 	roce->pdev = nic->pdev;
 	roce->ae_algo = nic->ae_algo;
-	roce->numa_node_mask = nic->numa_node_mask;
-
+	bitmap_copy(roce->numa_node_mask.bits, nic->numa_node_mask.bits,
+		    MAX_NUMNODES);
 	return 0;
 }
 
@@ -2698,8 +2722,7 @@
 	} else {
 		set_bit(HCLGEVF_STATE_DOWN, &hdev->state);
 
-		/* flush memory to make sure DOWN is seen by service task */
-		smp_mb__before_atomic();
+		smp_mb__after_atomic(); /* flush memory to make sure DOWN is seen by service task */
 		hclgevf_flush_link_update(hdev);
 	}
 }
@@ -2823,9 +2846,6 @@
 	hdev->num_msi = vectors;
 	hdev->num_msi_left = vectors;
 
-	hdev->base_msi_vector = pdev->irq;
-	hdev->roce_base_vector = pdev->irq + hdev->roce_base_msix_offset;
-
 	hdev->vector_status = devm_kcalloc(&pdev->dev, hdev->num_msi,
 					   sizeof(u16), GFP_KERNEL);
 	if (!hdev->vector_status) {
@@ -3013,7 +3033,10 @@
 
 	/* un-init roce, if it exists */
 	if (hdev->roce_client) {
+		while (test_bit(HCLGEVF_STATE_RST_HANDLING, &hdev->state))
+			msleep(HCLGEVF_WAIT_RESET_DONE);
 		clear_bit(HCLGEVF_STATE_ROCE_REGISTERED, &hdev->state);
+
 		hdev->roce_client->ops->uninit_instance(&hdev->roce, 0);
 		hdev->roce_client = NULL;
 		hdev->roce.client = NULL;
@@ -3022,6 +3045,8 @@
 	/* un-init nic/unic, if this was not called by roce client */
 	if (client->ops->uninit_instance && hdev->nic_client &&
 	    client->type != HNAE3_CLIENT_ROCE) {
+		while (test_bit(HCLGEVF_STATE_RST_HANDLING, &hdev->state))
+			msleep(HCLGEVF_WAIT_RESET_DONE);
 		clear_bit(HCLGEVF_STATE_NIC_REGISTERED, &hdev->state);
 
 		client->ops->uninit_instance(&hdev->nic, 0);
@@ -3254,7 +3279,8 @@
 	struct pci_dev *pdev = hdev->pdev;
 	int ret = 0;
 
-	if (hdev->reset_type == HNAE3_VF_FULL_RESET &&
+	if ((hdev->reset_type == HNAE3_VF_FULL_RESET ||
+	     hdev->reset_type == HNAE3_FLR_RESET) &&
 	    test_bit(HCLGEVF_STATE_IRQ_INITED, &hdev->state)) {
 		hclgevf_misc_irq_uninit(hdev);
 		hclgevf_uninit_msi(hdev);
@@ -3340,6 +3366,11 @@
 		return ret;
 	}
 
+	/* get current port based vlan state from PF */
+	ret = hclgevf_get_port_base_vlan_filter_state(hdev);
+	if (ret)
+		return ret;
+
 	set_bit(HCLGEVF_STATE_PROMISC_CHANGED, &hdev->state);
 
 	hclgevf_init_rxd_adv_layout(hdev);
@@ -3457,6 +3488,7 @@
 		 HCLGEVF_DRIVER_NAME);
 
 	hclgevf_task_schedule(hdev, round_jiffies_relative(HZ));
+	timer_setup(&hdev->reset_timer, hclgevf_reset_timer, 0);
 
 	return 0;
 
@@ -3796,7 +3828,7 @@
 }
 
 void hclgevf_update_port_base_vlan_info(struct hclgevf_dev *hdev, u16 state,
-					u8 *port_base_vlan_info, u8 data_size)
+				struct hclge_mbx_port_base_vlan *port_base_vlan)
 {
 	struct hnae3_handle *nic = &hdev->nic;
 	struct hclge_vf_to_pf_msg send_msg;
@@ -3821,7 +3853,7 @@
 	/* send msg to PF and wait update port based vlan info */
 	hclgevf_build_send_msg(&send_msg, HCLGE_MBX_SET_VLAN,
 			       HCLGE_MBX_PORT_BASE_VLAN_CFG);
-	memcpy(send_msg.data, port_base_vlan_info, data_size);
+	memcpy(send_msg.data, port_base_vlan, sizeof(*port_base_vlan));
 	ret = hclgevf_send_mbx_msg(hdev, &send_msg, false, NULL, 0);
 	if (!ret) {
 		if (state == HNAE3_PORT_BASE_VLAN_DISABLE)
@@ -3915,8 +3947,10 @@
 
 static void hclgevf_exit(void)
 {
+	hnae3_acquire_unload_lock();
 	hnae3_unregister_ae_algo(&ae_algovf);
 	destroy_workqueue(hclgevf_wq);
+	hnae3_release_unload_lock();
 }
 module_init(hclgevf_init);
 module_exit(hclgevf_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.h
@@ -109,6 +109,8 @@
 #define HCLGEVF_VF_RST_ING		0x07008
 #define HCLGEVF_VF_RST_ING_BIT		BIT(16)
 
+#define HCLGEVF_WAIT_RESET_DONE		100
+
 #define HCLGEVF_RSS_IND_TBL_SIZE		512
 #define HCLGEVF_RSS_SET_BITMAP_MSK	0xffff
 #define HCLGEVF_RSS_KEY_SIZE		40
@@ -279,6 +281,7 @@
 	enum hnae3_reset_type reset_level;
 	unsigned long reset_pending;
 	enum hnae3_reset_type reset_type;
+	struct timer_list reset_timer;
 
 #define HCLGEVF_RESET_REQUESTED		0
 #define HCLGEVF_RESET_PENDING		1
@@ -295,7 +298,7 @@
 	u16 rss_size_max;	/* HW defined max RSS task queue */
 
 	u16 num_alloc_vport;	/* num vports this driver supports */
-	u32 numa_node_mask;
+	nodemask_t numa_node_mask;
 	u16 rx_buf_len;
 	u16 num_tx_desc;	/* desc num of per tx queue */
 	u16 num_rx_desc;	/* desc num of per rx queue */
@@ -308,8 +311,6 @@
 	u16 num_nic_msix;	/* Num of nic vectors for this VF */
 	u16 num_roce_msix;	/* Num of roce vectors for this VF */
 	u16 roce_base_msix_offset;
-	int roce_base_vector;
-	u32 base_msi_vector;
 	u16 *vector_status;
 	int *vector_irq;
 
@@ -355,5 +356,5 @@
 void hclgevf_reset_task_schedule(struct hclgevf_dev *hdev);
 void hclgevf_mbx_task_schedule(struct hclgevf_dev *hdev);
 void hclgevf_update_port_base_vlan_info(struct hclgevf_dev *hdev, u16 state,
-					u8 *port_base_vlan_info, u8 data_size);
+			struct hclge_mbx_port_base_vlan *port_base_vlan);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_mbx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_mbx.c
@@ -60,6 +60,9 @@
 		i++;
 	}
 
+	/* ensure additional_info will be seen after received_resp */
+	smp_rmb();
+
 	if (i >= HCLGEVF_MAX_TRY_TIMES) {
 		dev_err(&hdev->pdev->dev,
 			"VF could not get mbx(%u,%u) resp(=%d) from PF in %d tries\n",
@@ -114,13 +117,14 @@
 
 	memcpy(&req->msg, send_msg, sizeof(struct hclge_vf_to_pf_msg));
 
-	trace_hclge_vf_mbx_send(hdev, req);
+	if (test_bit(HCLGEVF_STATE_NIC_REGISTERED, &hdev->state))
+		trace_hclge_vf_mbx_send(hdev, req);
 
 	/* synchronous send */
 	if (need_resp) {
 		mutex_lock(&hdev->mbx_resp.mbx_mutex);
 		hclgevf_reset_mbx_resp_status(hdev);
-		req->match_id = hdev->mbx_resp.match_id;
+		req->match_id = cpu_to_le16(hdev->mbx_resp.match_id);
 		status = hclgevf_cmd_send(&hdev->hw, &desc, 1);
 		if (status) {
 			dev_err(&hdev->pdev->dev,
@@ -158,27 +162,33 @@
 static void hclgevf_handle_mbx_response(struct hclgevf_dev *hdev,
 					struct hclge_mbx_pf_to_vf_cmd *req)
 {
+	u16 vf_mbx_msg_subcode = le16_to_cpu(req->msg.vf_mbx_msg_subcode);
+	u16 vf_mbx_msg_code = le16_to_cpu(req->msg.vf_mbx_msg_code);
 	struct hclgevf_mbx_resp_status *resp = &hdev->mbx_resp;
+	u16 resp_status = le16_to_cpu(req->msg.resp_status);
+	u16 match_id = le16_to_cpu(req->match_id);
 
 	if (resp->received_resp)
 		dev_warn(&hdev->pdev->dev,
-			 "VF mbx resp flag not clear(%u)\n",
-			 req->msg.vf_mbx_msg_code);
+			"VF mbx resp flag not clear(%u)\n",
+			 vf_mbx_msg_code);
 
-	resp->origin_mbx_msg =
-			(req->msg.vf_mbx_msg_code << 16);
-	resp->origin_mbx_msg |= req->msg.vf_mbx_msg_subcode;
-	resp->resp_status =
-		hclgevf_resp_to_errno(req->msg.resp_status);
+	resp->origin_mbx_msg = (vf_mbx_msg_code << 16);
+	resp->origin_mbx_msg |= vf_mbx_msg_subcode;
+	resp->resp_status = hclgevf_resp_to_errno(resp_status);
 	memcpy(resp->additional_info, req->msg.resp_data,
 	       HCLGE_MBX_MAX_RESP_DATA_SIZE * sizeof(u8));
-	if (req->match_id) {
+
+	/* ensure additional_info will be seen before setting received_resp */
+	smp_wmb();
+
+	if (match_id) {
 		/* If match_id is not zero, it means PF support match_id.
 		 * if the match_id is right, VF get the right response, or
 		 * ignore the response. and driver will clear hdev->mbx_resp
 		 * when send next message which need response.
 		 */
-		if (req->match_id == resp->match_id)
+		if (match_id == resp->match_id)
 			resp->received_resp = true;
 	} else {
 		resp->received_resp = true;
@@ -195,7 +205,7 @@
 	    HCLGE_MBX_MAX_ARQ_MSG_NUM) {
 		dev_warn(&hdev->pdev->dev,
 			 "Async Q full, dropping msg(%u)\n",
-			 req->msg.code);
+			 le16_to_cpu(req->msg.code));
 		return;
 	}
 
@@ -214,6 +224,7 @@
 	struct hclgevf_cmq_ring *crq;
 	struct hclgevf_desc *desc;
 	u16 flag;
+	u16 code;
 
 	crq = &hdev->hw.cmq.crq;
 
@@ -227,10 +238,11 @@
 		req = (struct hclge_mbx_pf_to_vf_cmd *)desc->data;
 
 		flag = le16_to_cpu(crq->desc[crq->next_to_use].flag);
+		code = le16_to_cpu(req->msg.code);
 		if (unlikely(!hnae3_get_bit(flag, HCLGEVF_CMDQ_RX_OUTVLD_B))) {
 			dev_warn(&hdev->pdev->dev,
 				 "dropped invalid mailbox message, code = %u\n",
-				 req->msg.code);
+				 code);
 
 			/* dropping/not processing this invalid message */
 			crq->desc[crq->next_to_use].flag = 0;
@@ -246,7 +258,7 @@
 		 * timeout and simultaneously queue the async messages for later
 		 * prcessing in context of mailbox task i.e. the slow path.
 		 */
-		switch (req->msg.code) {
+		switch (code) {
 		case HCLGE_MBX_PF_VF_RESP:
 			hclgevf_handle_mbx_response(hdev, req);
 			break;
@@ -260,7 +272,7 @@
 		default:
 			dev_err(&hdev->pdev->dev,
 				"VF received unsupported(%u) mbx msg from PF\n",
-				req->msg.code);
+				code);
 			break;
 		}
 		crq->desc[crq->next_to_use].flag = 0;
@@ -282,14 +294,18 @@
 
 void hclgevf_mbx_async_handler(struct hclgevf_dev *hdev)
 {
+	struct hclge_mbx_port_base_vlan *vlan_info;
+	struct hclge_mbx_link_status *link_info;
+	struct hclge_mbx_link_mode *link_mode;
 	enum hnae3_reset_type reset_type;
 	u16 link_status, state;
-	u16 *msg_q, *vlan_info;
+	__le16 *msg_q;
+	u16 opcode;
 	u8 duplex;
 	u32 speed;
 	u32 tail;
 	u8 flag;
-	u8 idx;
+	u16 idx;
 
 	tail = hdev->arq.tail;
 
@@ -302,13 +318,14 @@
 		}
 
 		msg_q = hdev->arq.msg_q[hdev->arq.head];
-
-		switch (msg_q[0]) {
+		opcode = le16_to_cpu(msg_q[0]);
+		switch (opcode) {
 		case HCLGE_MBX_LINK_STAT_CHANGE:
-			link_status = msg_q[1];
-			memcpy(&speed, &msg_q[2], sizeof(speed));
-			duplex = (u8)msg_q[4];
-			flag = (u8)msg_q[5];
+			link_info = (struct hclge_mbx_link_status *)(msg_q + 1);
+			link_status = le16_to_cpu(link_info->link_status);
+			speed = le32_to_cpu(link_info->speed);
+			duplex = (u8)le16_to_cpu(link_info->duplex);
+			flag = link_info->flag;
 
 			/* update upper layer with new link link status */
 			hclgevf_update_speed_duplex(hdev, speed, duplex);
@@ -320,13 +337,14 @@
 
 			break;
 		case HCLGE_MBX_LINK_STAT_MODE:
-			idx = (u8)msg_q[1];
+			link_mode = (struct hclge_mbx_link_mode *)(msg_q + 1);
+			idx = le16_to_cpu(link_mode->idx);
 			if (idx)
-				memcpy(&hdev->hw.mac.supported, &msg_q[2],
-				       sizeof(unsigned long));
+				hdev->hw.mac.supported =
+					le64_to_cpu(link_mode->link_mode);
 			else
-				memcpy(&hdev->hw.mac.advertising, &msg_q[2],
-				       sizeof(unsigned long));
+				hdev->hw.mac.advertising =
+					le64_to_cpu(link_mode->link_mode);
 			break;
 		case HCLGE_MBX_ASSERTING_RESET:
 			/* PF has asserted reset hence VF should go in pending
@@ -334,25 +352,27 @@
 			 * has been completely reset. After this stack should
 			 * eventually be re-initialized.
 			 */
-			reset_type = (enum hnae3_reset_type)msg_q[1];
+			reset_type =
+				(enum hnae3_reset_type)le16_to_cpu(msg_q[1]);
 			set_bit(reset_type, &hdev->reset_pending);
 			set_bit(HCLGEVF_RESET_PENDING, &hdev->reset_state);
 			hclgevf_reset_task_schedule(hdev);
 
 			break;
 		case HCLGE_MBX_PUSH_VLAN_INFO:
-			state = msg_q[1];
-			vlan_info = &msg_q[1];
+			vlan_info =
+				(struct hclge_mbx_port_base_vlan *)(msg_q + 1);
+			state = le16_to_cpu(vlan_info->state);
 			hclgevf_update_port_base_vlan_info(hdev, state,
-							   (u8 *)vlan_info, 8);
+							   vlan_info);
 			break;
 		case HCLGE_MBX_PUSH_PROMISC_INFO:
-			hclgevf_parse_promisc_info(hdev, msg_q[1]);
+			hclgevf_parse_promisc_info(hdev, le16_to_cpu(msg_q[1]));
 			break;
 		default:
 			dev_err(&hdev->pdev->dev,
 				"fetched unsupported(%u) message from arq\n",
-				msg_q[0]);
+				opcode);
 			break;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_trace.h
@@ -23,15 +23,15 @@
 		__field(u8, vfid)
 		__field(u16, code)
 		__string(pciname, pci_name(hdev->pdev))
-		__string(devname, &hdev->nic.kinfo.netdev->name)
+		__string(devname, hdev->nic.kinfo.netdev->name)
 		__array(u32, mbx_data, VF_GET_MBX_LEN)
 	),
 
 	TP_fast_assign(
 		__entry->vfid = req->dest_vfid;
-		__entry->code = req->msg.code;
+		__entry->code = le16_to_cpu(req->msg.code);
 		__assign_str(pciname, pci_name(hdev->pdev));
-		__assign_str(devname, &hdev->nic.kinfo.netdev->name);
+		__assign_str(devname, hdev->nic.kinfo.netdev->name);
 		memcpy(__entry->mbx_data, req,
 		       sizeof(struct hclge_mbx_pf_to_vf_cmd));
 	),
@@ -55,7 +55,7 @@
 		__field(u8, code)
 		__field(u8, subcode)
 		__string(pciname, pci_name(hdev->pdev))
-		__string(devname, &hdev->nic.kinfo.netdev->name)
+		__string(devname, hdev->nic.kinfo.netdev->name)
 		__array(u32, mbx_data, VF_SEND_MBX_LEN)
 	),
 
@@ -64,7 +64,7 @@
 		__entry->code = req->msg.code;
 		__entry->subcode = req->msg.subcode;
 		__assign_str(pciname, pci_name(hdev->pdev));
-		__assign_str(devname, &hdev->nic.kinfo.netdev->name);
+		__assign_str(devname, hdev->nic.kinfo.netdev->name);
 		memcpy(__entry->mbx_data, req,
 		       sizeof(struct hclge_mbx_vf_to_pf_cmd));
 	),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/hisilicon/hns_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/hisilicon/hns_mdio.c
@@ -497,6 +497,7 @@
 						MDIO_SC_RESET_ST;
 				}
 			}
+			of_node_put(reg_args.np);
 		} else {
 			dev_warn(&pdev->dev, "find syscon ret = %#x\n", ret);
 			mdio_dev->subctrl_vbase = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_debugfs.c
@@ -85,6 +85,7 @@
 	struct tag_sml_funcfg_tbl *funcfg_table_elem;
 	struct hinic_cmd_lt_rd *read_data;
 	u16 out_size = sizeof(*read_data);
+	int ret = ~0;
 	int err;
 
 	read_data = kzalloc(sizeof(*read_data), GFP_KERNEL);
@@ -111,20 +112,25 @@
 
 	switch (idx) {
 	case VALID:
-		return funcfg_table_elem->dw0.bs.valid;
+		ret = funcfg_table_elem->dw0.bs.valid;
+		break;
 	case RX_MODE:
-		return funcfg_table_elem->dw0.bs.nic_rx_mode;
+		ret = funcfg_table_elem->dw0.bs.nic_rx_mode;
+		break;
 	case MTU:
-		return funcfg_table_elem->dw1.bs.mtu;
+		ret = funcfg_table_elem->dw1.bs.mtu;
+		break;
 	case RQ_DEPTH:
-		return funcfg_table_elem->dw13.bs.cfg_rq_depth;
+		ret = funcfg_table_elem->dw13.bs.cfg_rq_depth;
+		break;
 	case QUEUE_NUM:
-		return funcfg_table_elem->dw13.bs.cfg_q_num;
+		ret = funcfg_table_elem->dw13.bs.cfg_q_num;
+		break;
 	}
 
 	kfree(read_data);
 
-	return ~0;
+	return ret;
 }
 
 static ssize_t hinic_dbg_cmd_read(struct file *filp, char __user *buffer, size_t count,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_dev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_dev.h
@@ -95,9 +95,6 @@
 	u16				sq_depth;
 	u16				rq_depth;
 
-	struct hinic_txq_stats          tx_stats;
-	struct hinic_rxq_stats          rx_stats;
-
 	u8				rss_tmpl_idx;
 	u8				rss_hash_engine;
 	u16				num_rss;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c
@@ -814,7 +814,6 @@
 {
 	struct hinic_hwif *hwif = attr->hwif;
 	struct pci_dev *pdev = hwif->pdev;
-	size_t cell_ctxt_size;
 
 	chain->hwif = hwif;
 	chain->chain_type  = attr->chain_type;
@@ -826,8 +825,8 @@
 
 	sema_init(&chain->sem, 1);
 
-	cell_ctxt_size = chain->num_cells * sizeof(*chain->cell_ctxt);
-	chain->cell_ctxt = devm_kzalloc(&pdev->dev, cell_ctxt_size, GFP_KERNEL);
+	chain->cell_ctxt = devm_kcalloc(&pdev->dev, chain->num_cells,
+					sizeof(*chain->cell_ctxt), GFP_KERNEL);
 	if (!chain->cell_ctxt)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_hw_cmdq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_hw_cmdq.c
@@ -796,11 +796,10 @@
 	struct hinic_cmdq_ctxt *cmdq_ctxts;
 	struct pci_dev *pdev = hwif->pdev;
 	struct hinic_pfhwdev *pfhwdev;
-	size_t cmdq_ctxts_size;
 	int err;
 
-	cmdq_ctxts_size = HINIC_MAX_CMDQ_TYPES * sizeof(*cmdq_ctxts);
-	cmdq_ctxts = devm_kzalloc(&pdev->dev, cmdq_ctxts_size, GFP_KERNEL);
+	cmdq_ctxts = devm_kcalloc(&pdev->dev, HINIC_MAX_CMDQ_TYPES,
+				  sizeof(*cmdq_ctxts), GFP_KERNEL);
 	if (!cmdq_ctxts)
 		return -ENOMEM;
 
@@ -884,7 +883,6 @@
 	struct hinic_func_to_io *func_to_io = cmdqs_to_func_to_io(cmdqs);
 	struct pci_dev *pdev = hwif->pdev;
 	struct hinic_hwdev *hwdev;
-	size_t saved_wqs_size;
 	u16 max_wqe_size;
 	int err;
 
@@ -895,8 +893,8 @@
 	if (!cmdqs->cmdq_buf_pool)
 		return -ENOMEM;
 
-	saved_wqs_size = HINIC_MAX_CMDQ_TYPES * sizeof(struct hinic_wq);
-	cmdqs->saved_wqs = devm_kzalloc(&pdev->dev, saved_wqs_size, GFP_KERNEL);
+	cmdqs->saved_wqs = devm_kcalloc(&pdev->dev, HINIC_MAX_CMDQ_TYPES,
+					sizeof(*cmdqs->saved_wqs), GFP_KERNEL);
 	if (!cmdqs->saved_wqs) {
 		err = -ENOMEM;
 		goto err_saved_wqs;
@@ -931,7 +929,7 @@
 
 err_set_cmdq_depth:
 	hinic_ceq_unregister_cb(&func_to_io->ceqs, HINIC_CEQ_CMDQ);
-
+	free_cmdq(&cmdqs->cmdq[HINIC_CMDQ_SYNC]);
 err_cmdq_ctxt:
 	hinic_wqs_cmdq_free(&cmdqs->cmdq_pages, cmdqs->saved_wqs,
 			    HINIC_MAX_CMDQ_TYPES);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.c
@@ -162,7 +162,6 @@
 	struct hinic_hwif *hwif = hwdev->hwif;
 	struct pci_dev *pdev = hwif->pdev;
 	int nr_irqs, num_aeqs, num_ceqs;
-	size_t msix_entries_size;
 	int i, err;
 
 	num_aeqs = HINIC_HWIF_NUM_AEQS(hwif);
@@ -171,8 +170,8 @@
 	if (nr_irqs > HINIC_HWIF_NUM_IRQS(hwif))
 		nr_irqs = HINIC_HWIF_NUM_IRQS(hwif);
 
-	msix_entries_size = nr_irqs * sizeof(*hwdev->msix_entries);
-	hwdev->msix_entries = devm_kzalloc(&pdev->dev, msix_entries_size,
+	hwdev->msix_entries = devm_kcalloc(&pdev->dev, nr_irqs,
+					   sizeof(*hwdev->msix_entries),
 					   GFP_KERNEL);
 	if (!hwdev->msix_entries)
 		return -ENOMEM;
@@ -893,7 +892,7 @@
 	if (err)
 		return -EINVAL;
 
-	interrupt_info->lli_credit_cnt = temp_info.lli_timer_cnt;
+	interrupt_info->lli_credit_cnt = temp_info.lli_credit_cnt;
 	interrupt_info->lli_timer_cnt = temp_info.lli_timer_cnt;
 
 	err = hinic_msg_to_mgmt(&pfhwdev->pf_to_mgmt, HINIC_MOD_COMM,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c
@@ -631,16 +631,15 @@
 	struct hinic_hwif *hwif = eq->hwif;
 	struct pci_dev *pdev = hwif->pdev;
 	u32 init_val, addr, val;
-	size_t addr_size;
 	int err, pg;
 
-	addr_size = eq->num_pages * sizeof(*eq->dma_addr);
-	eq->dma_addr = devm_kzalloc(&pdev->dev, addr_size, GFP_KERNEL);
+	eq->dma_addr = devm_kcalloc(&pdev->dev, eq->num_pages,
+				    sizeof(*eq->dma_addr), GFP_KERNEL);
 	if (!eq->dma_addr)
 		return -ENOMEM;
 
-	addr_size = eq->num_pages * sizeof(*eq->virt_addr);
-	eq->virt_addr = devm_kzalloc(&pdev->dev, addr_size, GFP_KERNEL);
+	eq->virt_addr = devm_kcalloc(&pdev->dev, eq->num_pages,
+				     sizeof(*eq->virt_addr), GFP_KERNEL);
 	if (!eq->virt_addr) {
 		err = -ENOMEM;
 		goto err_virt_addr_alloc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_hw_mgmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_hw_mgmt.c
@@ -643,6 +643,7 @@
 	err = alloc_msg_buf(pf_to_mgmt);
 	if (err) {
 		dev_err(&pdev->dev, "Failed to allocate msg buffers\n");
+		destroy_workqueue(pf_to_mgmt->workq);
 		hinic_health_reporters_destroy(hwdev->devlink_dev);
 		return err;
 	}
@@ -650,6 +651,7 @@
 	err = hinic_api_cmd_init(pf_to_mgmt->cmd_chain, hwif);
 	if (err) {
 		dev_err(&pdev->dev, "Failed to initialize cmd chains\n");
+		destroy_workqueue(pf_to_mgmt->workq);
 		hinic_health_reporters_destroy(hwdev->devlink_dev);
 		return err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_hw_wq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_hw_wq.c
@@ -193,20 +193,20 @@
 {
 	struct hinic_hwif *hwif = wqs->hwif;
 	struct pci_dev *pdev = hwif->pdev;
-	size_t size;
 
-	size = wqs->num_pages * sizeof(*wqs->page_paddr);
-	wqs->page_paddr = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	wqs->page_paddr = devm_kcalloc(&pdev->dev, wqs->num_pages,
+				       sizeof(*wqs->page_paddr), GFP_KERNEL);
 	if (!wqs->page_paddr)
 		return -ENOMEM;
 
-	size = wqs->num_pages * sizeof(*wqs->page_vaddr);
-	wqs->page_vaddr = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	wqs->page_vaddr = devm_kcalloc(&pdev->dev, wqs->num_pages,
+				       sizeof(*wqs->page_vaddr), GFP_KERNEL);
 	if (!wqs->page_vaddr)
 		goto err_page_vaddr;
 
-	size = wqs->num_pages * sizeof(*wqs->shadow_page_vaddr);
-	wqs->shadow_page_vaddr = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	wqs->shadow_page_vaddr = devm_kcalloc(&pdev->dev, wqs->num_pages,
+					      sizeof(*wqs->shadow_page_vaddr),
+					      GFP_KERNEL);
 	if (!wqs->shadow_page_vaddr)
 		goto err_page_shadow_vaddr;
 
@@ -379,15 +379,14 @@
 {
 	struct hinic_hwif *hwif = wq->hwif;
 	struct pci_dev *pdev = hwif->pdev;
-	size_t size;
 
-	size = wq->num_q_pages * wq->max_wqe_size;
-	wq->shadow_wqe = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	wq->shadow_wqe = devm_kcalloc(&pdev->dev, wq->num_q_pages,
+				      wq->max_wqe_size, GFP_KERNEL);
 	if (!wq->shadow_wqe)
 		return -ENOMEM;
 
-	size = wq->num_q_pages * sizeof(wq->prod_idx);
-	wq->shadow_idx = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	wq->shadow_idx = devm_kcalloc(&pdev->dev, wq->num_q_pages,
+				      sizeof(*wq->shadow_idx), GFP_KERNEL);
 	if (!wq->shadow_idx)
 		goto err_shadow_idx;
 
@@ -772,7 +771,7 @@
 	/* If we only have one page, still need to get shadown wqe when
 	 * wqe rolling-over page
 	 */
-	if (curr_pg != end_pg || MASKED_WQE_IDX(wq, end_prod_idx) < *prod_idx) {
+	if (curr_pg != end_pg || end_prod_idx < *prod_idx) {
 		void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
 
 		copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *prod_idx);
@@ -842,7 +841,10 @@
 
 	*cons_idx = curr_cons_idx;
 
-	if (curr_pg != end_pg) {
+	/* If we only have one page, still need to get shadown wqe when
+	 * wqe rolling-over page
+	 */
+	if (curr_pg != end_pg || end_cons_idx < curr_cons_idx) {
 		void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
 
 		copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *cons_idx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_main.c
@@ -62,8 +62,6 @@
 
 #define HINIC_LRO_RX_TIMER_DEFAULT	16
 
-#define VLAN_BITMAP_SIZE(nic_dev)       (ALIGN(VLAN_N_VID, 8) / 8)
-
 #define work_to_rx_mode_work(work)      \
 		container_of(work, struct hinic_rx_mode_work, work)
 
@@ -82,56 +80,44 @@
 			netdev_features_t pre_features,
 			netdev_features_t features, bool force_change);
 
-static void update_rx_stats(struct hinic_dev *nic_dev, struct hinic_rxq *rxq)
+static void gather_rx_stats(struct hinic_rxq_stats *nic_rx_stats, struct hinic_rxq *rxq)
 {
-	struct hinic_rxq_stats *nic_rx_stats = &nic_dev->rx_stats;
 	struct hinic_rxq_stats rx_stats;
 
-	u64_stats_init(&rx_stats.syncp);
-
 	hinic_rxq_get_stats(rxq, &rx_stats);
 
-	u64_stats_update_begin(&nic_rx_stats->syncp);
 	nic_rx_stats->bytes += rx_stats.bytes;
 	nic_rx_stats->pkts  += rx_stats.pkts;
 	nic_rx_stats->errors += rx_stats.errors;
 	nic_rx_stats->csum_errors += rx_stats.csum_errors;
 	nic_rx_stats->other_errors += rx_stats.other_errors;
-	u64_stats_update_end(&nic_rx_stats->syncp);
-
-	hinic_rxq_clean_stats(rxq);
 }
 
-static void update_tx_stats(struct hinic_dev *nic_dev, struct hinic_txq *txq)
+static void gather_tx_stats(struct hinic_txq_stats *nic_tx_stats, struct hinic_txq *txq)
 {
-	struct hinic_txq_stats *nic_tx_stats = &nic_dev->tx_stats;
 	struct hinic_txq_stats tx_stats;
 
-	u64_stats_init(&tx_stats.syncp);
-
 	hinic_txq_get_stats(txq, &tx_stats);
 
-	u64_stats_update_begin(&nic_tx_stats->syncp);
 	nic_tx_stats->bytes += tx_stats.bytes;
 	nic_tx_stats->pkts += tx_stats.pkts;
 	nic_tx_stats->tx_busy += tx_stats.tx_busy;
 	nic_tx_stats->tx_wake += tx_stats.tx_wake;
 	nic_tx_stats->tx_dropped += tx_stats.tx_dropped;
 	nic_tx_stats->big_frags_pkts += tx_stats.big_frags_pkts;
-	u64_stats_update_end(&nic_tx_stats->syncp);
-
-	hinic_txq_clean_stats(txq);
 }
 
-static void update_nic_stats(struct hinic_dev *nic_dev)
+static void gather_nic_stats(struct hinic_dev *nic_dev,
+			     struct hinic_rxq_stats *nic_rx_stats,
+			     struct hinic_txq_stats *nic_tx_stats)
 {
 	int i, num_qps = hinic_hwdev_num_qps(nic_dev->hwdev);
 
 	for (i = 0; i < num_qps; i++)
-		update_rx_stats(nic_dev, &nic_dev->rxqs[i]);
+		gather_rx_stats(nic_rx_stats, &nic_dev->rxqs[i]);
 
 	for (i = 0; i < num_qps; i++)
-		update_tx_stats(nic_dev, &nic_dev->txqs[i]);
+		gather_tx_stats(nic_tx_stats, &nic_dev->txqs[i]);
 }
 
 /**
@@ -144,13 +130,12 @@
 {
 	int err, i, j, num_txqs = hinic_hwdev_num_qps(nic_dev->hwdev);
 	struct net_device *netdev = nic_dev->netdev;
-	size_t txq_size;
 
 	if (nic_dev->txqs)
 		return -EINVAL;
 
-	txq_size = num_txqs * sizeof(*nic_dev->txqs);
-	nic_dev->txqs = devm_kzalloc(&netdev->dev, txq_size, GFP_KERNEL);
+	nic_dev->txqs = devm_kcalloc(&netdev->dev, num_txqs,
+				     sizeof(*nic_dev->txqs), GFP_KERNEL);
 	if (!nic_dev->txqs)
 		return -ENOMEM;
 
@@ -187,6 +172,7 @@
 	hinic_sq_dbgfs_uninit(nic_dev);
 
 	devm_kfree(&netdev->dev, nic_dev->txqs);
+	nic_dev->txqs = NULL;
 	return err;
 }
 
@@ -241,13 +227,12 @@
 {
 	int err, i, j, num_rxqs = hinic_hwdev_num_qps(nic_dev->hwdev);
 	struct net_device *netdev = nic_dev->netdev;
-	size_t rxq_size;
 
 	if (nic_dev->rxqs)
 		return -EINVAL;
 
-	rxq_size = num_rxqs * sizeof(*nic_dev->rxqs);
-	nic_dev->rxqs = devm_kzalloc(&netdev->dev, rxq_size, GFP_KERNEL);
+	nic_dev->rxqs = devm_kcalloc(&netdev->dev, num_rxqs,
+				     sizeof(*nic_dev->rxqs), GFP_KERNEL);
 	if (!nic_dev->rxqs)
 		return -ENOMEM;
 
@@ -284,6 +269,7 @@
 	hinic_rq_dbgfs_uninit(nic_dev);
 
 	devm_kfree(&netdev->dev, nic_dev->rxqs);
+	nic_dev->rxqs = NULL;
 	return err;
 }
 
@@ -562,8 +548,6 @@
 	netif_carrier_off(netdev);
 	netif_tx_disable(netdev);
 
-	update_nic_stats(nic_dev);
-
 	up(&nic_dev->mgmt_lock);
 
 	if (!HINIC_IS_VF(nic_dev->hwdev->hwif))
@@ -857,26 +841,19 @@
 			      struct rtnl_link_stats64 *stats)
 {
 	struct hinic_dev *nic_dev = netdev_priv(netdev);
-	struct hinic_rxq_stats *nic_rx_stats;
-	struct hinic_txq_stats *nic_tx_stats;
-
-	nic_rx_stats = &nic_dev->rx_stats;
-	nic_tx_stats = &nic_dev->tx_stats;
-
-	down(&nic_dev->mgmt_lock);
+	struct hinic_rxq_stats nic_rx_stats = {};
+	struct hinic_txq_stats nic_tx_stats = {};
 
 	if (nic_dev->flags & HINIC_INTF_UP)
-		update_nic_stats(nic_dev);
-
-	up(&nic_dev->mgmt_lock);
+		gather_nic_stats(nic_dev, &nic_rx_stats, &nic_tx_stats);
 
-	stats->rx_bytes   = nic_rx_stats->bytes;
-	stats->rx_packets = nic_rx_stats->pkts;
-	stats->rx_errors  = nic_rx_stats->errors;
-
-	stats->tx_bytes   = nic_tx_stats->bytes;
-	stats->tx_packets = nic_tx_stats->pkts;
-	stats->tx_errors  = nic_tx_stats->tx_dropped;
+	stats->rx_bytes   = nic_rx_stats.bytes;
+	stats->rx_packets = nic_rx_stats.pkts;
+	stats->rx_errors  = nic_rx_stats.errors;
+
+	stats->tx_bytes   = nic_tx_stats.bytes;
+	stats->tx_packets = nic_tx_stats.pkts;
+	stats->tx_errors  = nic_tx_stats.tx_dropped;
 }
 
 static int hinic_set_features(struct net_device *netdev,
@@ -1175,8 +1152,6 @@
 static int nic_dev_init(struct pci_dev *pdev)
 {
 	struct hinic_rx_mode_work *rx_mode_work;
-	struct hinic_txq_stats *tx_stats;
-	struct hinic_rxq_stats *rx_stats;
 	struct hinic_dev *nic_dev;
 	struct net_device *netdev;
 	struct hinic_hwdev *hwdev;
@@ -1237,15 +1212,8 @@
 
 	sema_init(&nic_dev->mgmt_lock, 1);
 
-	tx_stats = &nic_dev->tx_stats;
-	rx_stats = &nic_dev->rx_stats;
-
-	u64_stats_init(&tx_stats->syncp);
-	u64_stats_init(&rx_stats->syncp);
-
-	nic_dev->vlan_bitmap = devm_kzalloc(&pdev->dev,
-					    VLAN_BITMAP_SIZE(nic_dev),
-					    GFP_KERNEL);
+	nic_dev->vlan_bitmap = devm_bitmap_zalloc(&pdev->dev, VLAN_N_VID,
+						  GFP_KERNEL);
 	if (!nic_dev->vlan_bitmap) {
 		err = -ENOMEM;
 		goto err_vlan_bitmap;
@@ -1516,8 +1484,15 @@
 
 static int __init hinic_module_init(void)
 {
+	int ret;
+
 	hinic_dbg_register_debugfs(HINIC_DRV_NAME);
-	return pci_register_driver(&hinic_driver);
+
+	ret = pci_register_driver(&hinic_driver);
+	if (ret)
+		hinic_dbg_unregister_debugfs();
+
+	return ret;
 }
 
 static void __exit hinic_module_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_rx.c
@@ -73,17 +73,15 @@
 	struct hinic_rxq_stats *rxq_stats = &rxq->rxq_stats;
 	unsigned int start;
 
-	u64_stats_update_begin(&stats->syncp);
 	do {
-		start = u64_stats_fetch_begin(&rxq_stats->syncp);
+		start = u64_stats_fetch_begin_irq(&rxq_stats->syncp);
 		stats->pkts = rxq_stats->pkts;
 		stats->bytes = rxq_stats->bytes;
 		stats->errors = rxq_stats->csum_errors +
 				rxq_stats->other_errors;
 		stats->csum_errors = rxq_stats->csum_errors;
 		stats->other_errors = rxq_stats->other_errors;
-	} while (u64_stats_fetch_retry(&rxq_stats->syncp, start));
-	u64_stats_update_end(&stats->syncp);
+	} while (u64_stats_fetch_retry_irq(&rxq_stats->syncp, start));
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
@@ -1180,7 +1180,6 @@
 			dev_err(&hwdev->hwif->pdev->dev,
 				"Failed to register VF, err: %d, status: 0x%x, out size: 0x%x\n",
 				err, register_info.status, out_size);
-			hinic_unregister_vf_mbox_cb(hwdev, HINIC_MOD_L2NIC);
 			return -EIO;
 		}
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/huawei/hinic/hinic_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/huawei/hinic/hinic_tx.c
@@ -97,17 +97,15 @@
 	struct hinic_txq_stats *txq_stats = &txq->txq_stats;
 	unsigned int start;
 
-	u64_stats_update_begin(&stats->syncp);
 	do {
-		start = u64_stats_fetch_begin(&txq_stats->syncp);
+		start = u64_stats_fetch_begin_irq(&txq_stats->syncp);
 		stats->pkts    = txq_stats->pkts;
 		stats->bytes   = txq_stats->bytes;
 		stats->tx_busy = txq_stats->tx_busy;
 		stats->tx_wake = txq_stats->tx_wake;
 		stats->tx_dropped = txq_stats->tx_dropped;
 		stats->big_frags_pkts = txq_stats->big_frags_pkts;
-	} while (u64_stats_fetch_retry(&txq_stats->syncp, start));
-	u64_stats_update_end(&stats->syncp);
+	} while (u64_stats_fetch_retry_irq(&txq_stats->syncp, start));
 }
 
 /**
@@ -862,7 +860,6 @@
 	struct hinic_dev *nic_dev = netdev_priv(netdev);
 	struct hinic_hwdev *hwdev = nic_dev->hwdev;
 	int err, irqname_len;
-	size_t sges_size;
 
 	txq->netdev = netdev;
 	txq->sq = sq;
@@ -871,13 +868,13 @@
 
 	txq->max_sges = HINIC_MAX_SQ_BUFDESCS;
 
-	sges_size = txq->max_sges * sizeof(*txq->sges);
-	txq->sges = devm_kzalloc(&netdev->dev, sges_size, GFP_KERNEL);
+	txq->sges = devm_kcalloc(&netdev->dev, txq->max_sges,
+				 sizeof(*txq->sges), GFP_KERNEL);
 	if (!txq->sges)
 		return -ENOMEM;
 
-	sges_size = txq->max_sges * sizeof(*txq->free_sges);
-	txq->free_sges = devm_kzalloc(&netdev->dev, sges_size, GFP_KERNEL);
+	txq->free_sges = devm_kcalloc(&netdev->dev, txq->max_sges,
+				      sizeof(*txq->free_sges), GFP_KERNEL);
 	if (!txq->free_sges) {
 		err = -ENOMEM;
 		goto err_alloc_free_sges;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/i825xx/sni_82596.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/i825xx/sni_82596.c
@@ -117,9 +117,10 @@
 	netdevice->dev_addr[5] = readb(eth_addr + 0x06);
 	iounmap(eth_addr);
 
-	if (!netdevice->irq) {
+	if (netdevice->irq < 0) {
 		printk(KERN_ERR "%s: IRQ not found for i82596 at 0x%lx\n",
 			__FILE__, netdevice->base_addr);
+		retval = netdevice->irq;
 		goto probe_failed;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/i825xx/sun3_82586.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/i825xx/sun3_82586.c
@@ -461,7 +461,7 @@
 	ias_cmd->cmd_cmd	= swab16(CMD_IASETUP | CMD_LAST);
 	ias_cmd->cmd_link	= 0xffff;
 
-	memcpy((char *)&ias_cmd->iaddr,(char *) dev->dev_addr,ETH_ALEN);
+	memcpy((char *)&ias_cmd->iaddr,(const char *) dev->dev_addr,ETH_ALEN);
 
 	p->scb->cbl_offset = make16(ias_cmd);
 
@@ -987,7 +987,7 @@
 	{
 #ifdef DEBUG
 		printk("%s: xmitter timed out, try to restart! stat: %02x\n",dev->name,p->scb->cus);
-		printk("%s: command-stats: %04x %04x\n",dev->name,swab16(p->xmit_cmds[0]->cmd_status),swab16(p->xmit_cmds[1]->cmd_status));
+		printk("%s: command-stats: %04x\n", dev->name, swab16(p->xmit_cmds[0]->cmd_status));
 		printk("%s: check, whether you set the right interrupt number!\n",dev->name);
 #endif
 		sun3_82586_close(dev);
@@ -1012,6 +1012,7 @@
 	if(skb->len > XMIT_BUFF_SIZE)
 	{
 		printk("%s: Sorry, max. framelength is %d bytes. The length of your frame is %d bytes.\n",dev->name,XMIT_BUFF_SIZE,skb->len);
+		dev_kfree_skb(skb);
 		return NETDEV_TX_OK;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ibm/ehea/ehea_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ibm/ehea/ehea_main.c
@@ -2898,6 +2898,7 @@
 	ret = of_device_register(&port->ofdev);
 	if (ret) {
 		pr_err("failed to register device. ret=%d\n", ret);
+		put_device(&port->ofdev.dev);
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ibm/emac/mal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ibm/emac/mal.c
@@ -576,7 +576,7 @@
 		printk(KERN_ERR "%pOF: Support for 405EZ not enabled!\n",
 				ofdev->dev.of_node);
 		err = -ENODEV;
-		goto fail;
+		goto fail_unmap;
 #endif
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ibm/ibmveth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ibm/ibmveth.c
@@ -196,7 +196,7 @@
 	unsigned long offset;
 
 	for (offset = 0; offset < length; offset += SMP_CACHE_BYTES)
-		asm("dcbfl %0,%1" :: "b" (addr), "r" (offset));
+		asm("dcbf %0,%1,1" :: "b" (addr), "r" (offset));
 }
 
 /* replenish the buffers for a pool.  note that we don't need to
@@ -1297,24 +1297,23 @@
 	 * the user space for finding a flow. During this process, OVS computes
 	 * checksum on the first packet when CHECKSUM_PARTIAL flag is set.
 	 *
-	 * So, re-compute TCP pseudo header checksum when configured for
-	 * trunk mode.
+	 * So, re-compute TCP pseudo header checksum.
 	 */
+
 	if (iph_proto == IPPROTO_TCP) {
 		struct tcphdr *tcph = (struct tcphdr *)(skb->data + iphlen);
+
 		if (tcph->check == 0x0000) {
 			/* Recompute TCP pseudo header checksum  */
-			if (adapter->is_active_trunk) {
-				tcphdrlen = skb->len - iphlen;
-				if (skb_proto == ETH_P_IP)
-					tcph->check =
-					 ~csum_tcpudp_magic(iph->saddr,
-					iph->daddr, tcphdrlen, iph_proto, 0);
-				else if (skb_proto == ETH_P_IPV6)
-					tcph->check =
-					 ~csum_ipv6_magic(&iph6->saddr,
-					&iph6->daddr, tcphdrlen, iph_proto, 0);
-			}
+			tcphdrlen = skb->len - iphlen;
+			if (skb_proto == ETH_P_IP)
+				tcph->check =
+				 ~csum_tcpudp_magic(iph->saddr,
+				iph->daddr, tcphdrlen, iph_proto, 0);
+			else if (skb_proto == ETH_P_IPV6)
+				tcph->check =
+				 ~csum_ipv6_magic(&iph6->saddr,
+				&iph6->daddr, tcphdrlen, iph_proto, 0);
 			/* Setup SKB fields for checksum offload */
 			skb_partial_csum_set(skb, iphlen,
 					     offsetof(struct tcphdr, check));
@@ -1620,7 +1619,7 @@
 		return rc;
 	}
 
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ibm/ibmvnic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ibm/ibmvnic.c
@@ -108,6 +108,7 @@
 static int send_query_phys_parms(struct ibmvnic_adapter *adapter);
 static void ibmvnic_tx_scrq_clean_buffer(struct ibmvnic_adapter *adapter,
 					 struct ibmvnic_sub_crq_queue *tx_scrq);
+static void ibmvnic_disable_irqs(struct ibmvnic_adapter *adapter);
 
 struct ibmvnic_stat {
 	char name[ETH_GSTRING_LEN];
@@ -1006,12 +1007,22 @@
 
 static void release_login_buffer(struct ibmvnic_adapter *adapter)
 {
+	if (!adapter->login_buf)
+		return;
+
+	dma_unmap_single(&adapter->vdev->dev, adapter->login_buf_token,
+			 adapter->login_buf_sz, DMA_TO_DEVICE);
 	kfree(adapter->login_buf);
 	adapter->login_buf = NULL;
 }
 
 static void release_login_rsp_buffer(struct ibmvnic_adapter *adapter)
 {
+	if (!adapter->login_rsp_buf)
+		return;
+
+	dma_unmap_single(&adapter->vdev->dev, adapter->login_rsp_buf_token,
+			 adapter->login_rsp_buf_sz, DMA_FROM_DEVICE);
 	kfree(adapter->login_rsp_buf);
 	adapter->login_rsp_buf = NULL;
 }
@@ -1239,16 +1250,32 @@
 		if (prev_state == VNIC_CLOSED)
 			enable_irq(adapter->tx_scrq[i]->irq);
 		enable_scrq_irq(adapter, adapter->tx_scrq[i]);
-		netdev_tx_reset_queue(netdev_get_tx_queue(netdev, i));
+		/* netdev_tx_reset_queue will reset dql stats. During NON_FATAL
+		 * resets, don't reset the stats because there could be batched
+		 * skb's waiting to be sent. If we reset dql stats, we risk
+		 * num_completed being greater than num_queued. This will cause
+		 * a BUG_ON in dql_completed().
+		 */
+		if (adapter->reset_reason != VNIC_RESET_NON_FATAL)
+			netdev_tx_reset_queue(netdev_get_tx_queue(netdev, i));
 	}
 
 	rc = set_link_state(adapter, IBMVNIC_LOGICAL_LNK_UP);
 	if (rc) {
 		ibmvnic_napi_disable(adapter);
-		release_resources(adapter);
+		ibmvnic_disable_irqs(adapter);
 		return rc;
 	}
 
+	adapter->tx_queues_active = true;
+
+	/* Since queues were stopped until now, there shouldn't be any
+	 * one in ibmvnic_complete_tx() or ibmvnic_xmit() so maybe we
+	 * don't need the synchronize_rcu()? Leaving it for consistency
+	 * with setting ->tx_queues_active = false.
+	 */
+	synchronize_rcu();
+
 	netif_tx_start_all_queues(netdev);
 
 	if (prev_state == VNIC_CLOSED) {
@@ -1295,7 +1322,6 @@
 		rc = init_resources(adapter);
 		if (rc) {
 			netdev_err(netdev, "failed to initialize resources\n");
-			release_resources(adapter);
 			goto out;
 		}
 	}
@@ -1312,6 +1338,11 @@
 		adapter->state = VNIC_OPEN;
 		rc = 0;
 	}
+
+	if (rc) {
+		release_resources(adapter);
+	}
+
 	return rc;
 }
 
@@ -1417,6 +1448,14 @@
 	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
 
 	/* ensure that transmissions are stopped if called by do_reset */
+
+	adapter->tx_queues_active = false;
+
+	/* Ensure complete_tx() and ibmvnic_xmit() see ->tx_queues_active
+	 * update so they don't restart a queue after we stop it below.
+	 */
+	synchronize_rcu();
+
 	if (test_bit(0, &adapter->resetting))
 		netif_tx_disable(netdev);
 	else
@@ -1657,14 +1696,21 @@
 		tx_buff->skb = NULL;
 		adapter->netdev->stats.tx_dropped++;
 	}
+
 	ind_bufp->index = 0;
+
 	if (atomic_sub_return(entries, &tx_scrq->used) <=
 	    (adapter->req_tx_entries_per_subcrq / 2) &&
-	    __netif_subqueue_stopped(adapter->netdev, queue_num) &&
-	    !test_bit(0, &adapter->resetting)) {
-		netif_wake_subqueue(adapter->netdev, queue_num);
-		netdev_dbg(adapter->netdev, "Started queue %d\n",
-			   queue_num);
+	    __netif_subqueue_stopped(adapter->netdev, queue_num)) {
+		rcu_read_lock();
+
+		if (adapter->tx_queues_active) {
+			netif_wake_subqueue(adapter->netdev, queue_num);
+			netdev_dbg(adapter->netdev, "Started queue %d\n",
+				   queue_num);
+		}
+
+		rcu_read_unlock();
 	}
 }
 
@@ -1719,13 +1765,12 @@
 	int index = 0;
 	u8 proto = 0;
 
-	tx_scrq = adapter->tx_scrq[queue_num];
-	txq = netdev_get_tx_queue(netdev, queue_num);
-	ind_bufp = &tx_scrq->ind_buf;
-
-	if (test_bit(0, &adapter->resetting)) {
-		if (!netif_subqueue_stopped(netdev, skb))
-			netif_stop_subqueue(netdev, queue_num);
+	/* If a reset is in progress, drop the packet since
+	 * the scrqs may get torn down. Otherwise use the
+	 * rcu to ensure reset waits for us to complete.
+	 */
+	rcu_read_lock();
+	if (!adapter->tx_queues_active) {
 		dev_kfree_skb_any(skb);
 
 		tx_send_failed++;
@@ -1734,6 +1779,10 @@
 		goto out;
 	}
 
+	tx_scrq = adapter->tx_scrq[queue_num];
+	txq = netdev_get_tx_queue(netdev, queue_num);
+	ind_bufp = &tx_scrq->ind_buf;
+
 	if (ibmvnic_xmit_workarounds(skb, netdev)) {
 		tx_dropped++;
 		tx_send_failed++;
@@ -1741,6 +1790,7 @@
 		ibmvnic_tx_scrq_flush(adapter, tx_scrq);
 		goto out;
 	}
+
 	if (skb_is_gso(skb))
 		tx_pool = &adapter->tso_pool[queue_num];
 	else
@@ -1790,6 +1840,18 @@
 	    (tx_pool->consumer_index + 1) % tx_pool->num_buffers;
 
 	tx_buff = &tx_pool->tx_buff[index];
+
+	/* Sanity checks on our free map to make sure it points to an index
+	 * that is not being occupied by another skb. If skb memory is
+	 * not freed then we see congestion control kick in and halt tx.
+	 */
+	if (unlikely(tx_buff->skb)) {
+		dev_warn_ratelimited(dev, "TX free map points to untracked skb (%s %d idx=%d)\n",
+				     skb_is_gso(skb) ? "tso_pool" : "tx_pool",
+				     queue_num, index);
+		dev_kfree_skb_any(tx_buff->skb);
+	}
+
 	tx_buff->skb = skb;
 	tx_buff->index = index;
 	tx_buff->pool_index = queue_num;
@@ -1895,6 +1957,7 @@
 		netif_carrier_off(netdev);
 	}
 out:
+	rcu_read_unlock();
 	netdev->stats.tx_dropped += tx_dropped;
 	netdev->stats.tx_bytes += tx_bytes;
 	netdev->stats.tx_packets += tx_packets;
@@ -2030,6 +2093,19 @@
 }
 
 /*
+ * Initialize the init_done completion and return code values. We
+ * can get a transport event just after registering the CRQ and the
+ * tasklet will use this to communicate the transport event. To ensure
+ * we don't miss the notification/error, initialize these _before_
+ * regisering the CRQ.
+ */
+static inline void reinit_init_done(struct ibmvnic_adapter *adapter)
+{
+	reinit_completion(&adapter->init_done);
+	adapter->init_done_rc = 0;
+}
+
+/*
  * do_reset returns zero if we are able to keep processing reset events, or
  * non-zero if we hit a fatal error and must halt.
  */
@@ -2135,6 +2211,8 @@
 		 */
 		adapter->state = VNIC_PROBED;
 
+		reinit_init_done(adapter);
+
 		if (adapter->reset_reason == VNIC_RESET_CHANGE_PARAM) {
 			rc = init_crq_queue(adapter);
 		} else if (adapter->reset_reason == VNIC_RESET_MOBILITY) {
@@ -2280,7 +2358,8 @@
 	 */
 	adapter->state = VNIC_PROBED;
 
-	reinit_completion(&adapter->init_done);
+	reinit_init_done(adapter);
+
 	rc = init_crq_queue(adapter);
 	if (rc) {
 		netdev_err(adapter->netdev,
@@ -2421,22 +2500,82 @@
 static void __ibmvnic_reset(struct work_struct *work)
 {
 	struct ibmvnic_adapter *adapter;
-	bool saved_state = false;
+	unsigned int timeout = 5000;
 	struct ibmvnic_rwi *tmprwi;
+	bool saved_state = false;
 	struct ibmvnic_rwi *rwi;
 	unsigned long flags;
+	struct device *dev;
+	bool need_reset;
+	int num_fails = 0;
 	u32 reset_state;
 	int rc = 0;
 
 	adapter = container_of(work, struct ibmvnic_adapter, ibmvnic_reset);
+		dev = &adapter->vdev->dev;
 
-	if (test_and_set_bit_lock(0, &adapter->resetting)) {
+	/* Wait for ibmvnic_probe() to complete. If probe is taking too long
+	 * or if another reset is in progress, defer work for now. If probe
+	 * eventually fails it will flush and terminate our work.
+	 *
+	 * Three possibilities here:
+	 * 1. Adpater being removed  - just return
+	 * 2. Timed out on probe or another reset in progress - delay the work
+	 * 3. Completed probe - perform any resets in queue
+	 */
+	if (adapter->state == VNIC_PROBING &&
+	    !wait_for_completion_timeout(&adapter->probe_done, timeout)) {
+		dev_err(dev, "Reset thread timed out on probe");
 		queue_delayed_work(system_long_wq,
 				   &adapter->ibmvnic_delayed_reset,
 				   IBMVNIC_RESET_DELAY);
 		return;
 	}
 
+	/* adapter is done with probe (i.e state is never VNIC_PROBING now) */
+	if (adapter->state == VNIC_REMOVING)
+		return;
+
+	/* ->rwi_list is stable now (no one else is removing entries) */
+
+	/* ibmvnic_probe() may have purged the reset queue after we were
+	 * scheduled to process a reset so there maybe no resets to process.
+	 * Before setting the ->resetting bit though, we have to make sure
+	 * that there is infact a reset to process. Otherwise we may race
+	 * with ibmvnic_open() and end up leaving the vnic down:
+	 *
+	 *	__ibmvnic_reset()	    ibmvnic_open()
+	 *	-----------------	    --------------
+	 *
+	 *  set ->resetting bit
+	 *  				find ->resetting bit is set
+	 *  				set ->state to IBMVNIC_OPEN (i.e
+	 *  				assume reset will open device)
+	 *  				return
+	 *  find reset queue empty
+	 *  return
+	 *
+	 *  	Neither performed vnic login/open and vnic stays down
+	 *
+	 * If we hold the lock and conditionally set the bit, either we
+	 * or ibmvnic_open() will complete the open.
+	 */
+	need_reset = false;
+	spin_lock(&adapter->rwi_lock);
+	if (!list_empty(&adapter->rwi_list)) {
+		if (test_and_set_bit_lock(0, &adapter->resetting)) {
+			queue_delayed_work(system_long_wq,
+					   &adapter->ibmvnic_delayed_reset,
+					   IBMVNIC_RESET_DELAY);
+		} else {
+			need_reset = true;
+		}
+	}
+	spin_unlock(&adapter->rwi_lock);
+
+	if (!need_reset)
+		return;
+
 	rwi = get_next_rwi(adapter);
 	while (rwi) {
 		spin_lock_irqsave(&adapter->state_lock, flags);
@@ -2479,11 +2618,23 @@
 				rc = do_hard_reset(adapter, rwi, reset_state);
 				rtnl_unlock();
 			}
-			if (rc) {
-				/* give backing device time to settle down */
+			if (rc)
+				num_fails++;
+			else
+				num_fails = 0;
+
+			/* If auto-priority-failover is enabled we can get
+			 * back to back failovers during resets, resulting
+			 * in at least two failed resets (from high-priority
+			 * backing device to low-priority one and then back)
+			 * If resets continue to fail beyond that, give the
+			 * adapter some time to settle down before retrying.
+			 */
+			if (num_fails >= 3) {
 				netdev_dbg(adapter->netdev,
-					   "[S:%s] Hard reset failed, waiting 60 secs\n",
-					   adapter_state_to_string(adapter->state));
+					   "[S:%s] Hard reset failed %d times, waiting 60 secs\n",
+					   adapter_state_to_string(adapter->state),
+					   num_fails);
 				set_current_state(TASK_UNINTERRUPTIBLE);
 				schedule_timeout(60 * HZ);
 			}
@@ -2499,19 +2650,19 @@
 		rwi = get_next_rwi(adapter);
 
 		/*
-		 * If there is another reset queued, free the previous rwi
-		 * and process the new reset even if previous reset failed
-		 * (the previous reset could have failed because of a fail
-		 * over for instance, so process the fail over).
-		 *
 		 * If there are no resets queued and the previous reset failed,
 		 * the adapter would be in an undefined state. So retry the
 		 * previous reset as a hard reset.
+		 *
+		 * Else, free the previous rwi and, if there is another reset
+		 * queued, process the new reset even if previous reset failed
+		 * (the previous reset could have failed because of a fail
+		 * over for instance, so process the fail over).
 		 */
-		if (rwi)
-			kfree(tmprwi);
-		else if (rc)
+		if (!rwi && rc)
 			rwi = tmprwi;
+		else
+			kfree(tmprwi);
 
 		if (rwi && (rwi->reset_reason == VNIC_RESET_FAILOVER ||
 			    rwi->reset_reason == VNIC_RESET_MOBILITY || rc))
@@ -2541,12 +2692,23 @@
 	__ibmvnic_reset(&adapter->ibmvnic_reset);
 }
 
+static void flush_reset_queue(struct ibmvnic_adapter *adapter)
+{
+	struct list_head *entry, *tmp_entry;
+
+	if (!list_empty(&adapter->rwi_list)) {
+		list_for_each_safe(entry, tmp_entry, &adapter->rwi_list) {
+			list_del(entry);
+			kfree(list_entry(entry, struct ibmvnic_rwi, list));
+		}
+	}
+}
+
 static int ibmvnic_reset(struct ibmvnic_adapter *adapter,
 			 enum ibmvnic_reset_reason reason)
 {
-	struct list_head *entry, *tmp_entry;
-	struct ibmvnic_rwi *rwi, *tmp;
 	struct net_device *netdev = adapter->netdev;
+	struct ibmvnic_rwi *rwi, *tmp;
 	unsigned long flags;
 	int ret;
 
@@ -2565,13 +2727,6 @@
 		goto err;
 	}
 
-	if (adapter->state == VNIC_PROBING) {
-		netdev_warn(netdev, "Adapter reset during probe\n");
-		adapter->init_done_rc = EAGAIN;
-		ret = EAGAIN;
-		goto err;
-	}
-
 	list_for_each_entry(tmp, &adapter->rwi_list, list) {
 		if (tmp->reset_reason == reason) {
 			netdev_dbg(netdev, "Skipping matching reset, reason=%s\n",
@@ -2589,10 +2744,9 @@
 	/* if we just received a transport event,
 	 * flush reset queue and process this reset
 	 */
-	if (adapter->force_reset_recovery && !list_empty(&adapter->rwi_list)) {
-		list_for_each_safe(entry, tmp_entry, &adapter->rwi_list)
-			list_del(entry);
-	}
+	if (adapter->force_reset_recovery)
+		flush_reset_queue(adapter);
+
 	rwi->reset_reason = reason;
 	list_add_tail(&rwi->list, &adapter->rwi_list);
 	netdev_dbg(adapter->netdev, "Scheduling reset (reason %s)\n",
@@ -2904,13 +3058,8 @@
 {
 	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
 
-	if (adapter->priv_flags & IBMVNIC_USE_SERVER_MAXES) {
-		ring->rx_max_pending = adapter->max_rx_add_entries_per_subcrq;
-		ring->tx_max_pending = adapter->max_tx_entries_per_subcrq;
-	} else {
-		ring->rx_max_pending = IBMVNIC_MAX_QUEUE_SZ;
-		ring->tx_max_pending = IBMVNIC_MAX_QUEUE_SZ;
-	}
+	ring->rx_max_pending = adapter->max_rx_add_entries_per_subcrq;
+	ring->tx_max_pending = adapter->max_tx_entries_per_subcrq;
 	ring->rx_mini_max_pending = 0;
 	ring->rx_jumbo_max_pending = 0;
 	ring->rx_pending = adapter->req_rx_add_entries_per_subcrq;
@@ -2923,23 +3072,21 @@
 				 struct ethtool_ringparam *ring)
 {
 	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
-	int ret;
 
-	ret = 0;
+	if (ring->rx_pending > adapter->max_rx_add_entries_per_subcrq  ||
+	    ring->tx_pending > adapter->max_tx_entries_per_subcrq) {
+		netdev_err(netdev, "Invalid request.\n");
+		netdev_err(netdev, "Max tx buffers = %llu\n",
+			   adapter->max_rx_add_entries_per_subcrq);
+		netdev_err(netdev, "Max rx buffers = %llu\n",
+			   adapter->max_tx_entries_per_subcrq);
+		return -EINVAL;
+	}
+
 	adapter->desired.rx_entries = ring->rx_pending;
 	adapter->desired.tx_entries = ring->tx_pending;
 
-	ret = wait_for_reset(adapter);
-
-	if (!ret &&
-	    (adapter->req_rx_add_entries_per_subcrq != ring->rx_pending ||
-	     adapter->req_tx_entries_per_subcrq != ring->tx_pending))
-		netdev_info(netdev,
-			    "Could not match full ringsize request. Requested: RX %d, TX %d; Allowed: RX %llu, TX %llu\n",
-			    ring->rx_pending, ring->tx_pending,
-			    adapter->req_rx_add_entries_per_subcrq,
-			    adapter->req_tx_entries_per_subcrq);
-	return ret;
+	return wait_for_reset(adapter);
 }
 
 static void ibmvnic_get_channels(struct net_device *netdev,
@@ -2947,14 +3094,8 @@
 {
 	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
 
-	if (adapter->priv_flags & IBMVNIC_USE_SERVER_MAXES) {
-		channels->max_rx = adapter->max_rx_queues;
-		channels->max_tx = adapter->max_tx_queues;
-	} else {
-		channels->max_rx = IBMVNIC_MAX_QUEUES;
-		channels->max_tx = IBMVNIC_MAX_QUEUES;
-	}
-
+	channels->max_rx = adapter->max_rx_queues;
+	channels->max_tx = adapter->max_tx_queues;
 	channels->max_other = 0;
 	channels->max_combined = 0;
 	channels->rx_count = adapter->req_rx_queues;
@@ -2967,22 +3108,11 @@
 				struct ethtool_channels *channels)
 {
 	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
-	int ret;
 
-	ret = 0;
 	adapter->desired.rx_queues = channels->rx_count;
 	adapter->desired.tx_queues = channels->tx_count;
 
-	ret = wait_for_reset(adapter);
-
-	if (!ret &&
-	    (adapter->req_rx_queues != channels->rx_count ||
-	     adapter->req_tx_queues != channels->tx_count))
-		netdev_info(netdev,
-			    "Could not match full channels request. Requested: RX %d, TX %d; Allowed: RX %llu, TX %llu\n",
-			    channels->rx_count, channels->tx_count,
-			    adapter->req_rx_queues, adapter->req_tx_queues);
-	return ret;
+	return wait_for_reset(adapter);
 }
 
 static void ibmvnic_get_strings(struct net_device *dev, u32 stringset, u8 *data)
@@ -2990,43 +3120,32 @@
 	struct ibmvnic_adapter *adapter = netdev_priv(dev);
 	int i;
 
-	switch (stringset) {
-	case ETH_SS_STATS:
-		for (i = 0; i < ARRAY_SIZE(ibmvnic_stats);
-				i++, data += ETH_GSTRING_LEN)
-			memcpy(data, ibmvnic_stats[i].name, ETH_GSTRING_LEN);
-
-		for (i = 0; i < adapter->req_tx_queues; i++) {
-			snprintf(data, ETH_GSTRING_LEN, "tx%d_packets", i);
-			data += ETH_GSTRING_LEN;
-
-			snprintf(data, ETH_GSTRING_LEN, "tx%d_bytes", i);
-			data += ETH_GSTRING_LEN;
-
-			snprintf(data, ETH_GSTRING_LEN,
-				 "tx%d_dropped_packets", i);
-			data += ETH_GSTRING_LEN;
-		}
+	if (stringset != ETH_SS_STATS)
+		return;
 
-		for (i = 0; i < adapter->req_rx_queues; i++) {
-			snprintf(data, ETH_GSTRING_LEN, "rx%d_packets", i);
-			data += ETH_GSTRING_LEN;
+	for (i = 0; i < ARRAY_SIZE(ibmvnic_stats); i++, data += ETH_GSTRING_LEN)
+		memcpy(data, ibmvnic_stats[i].name, ETH_GSTRING_LEN);
 
-			snprintf(data, ETH_GSTRING_LEN, "rx%d_bytes", i);
-			data += ETH_GSTRING_LEN;
+	for (i = 0; i < adapter->req_tx_queues; i++) {
+		snprintf(data, ETH_GSTRING_LEN, "tx%d_packets", i);
+		data += ETH_GSTRING_LEN;
 
-			snprintf(data, ETH_GSTRING_LEN, "rx%d_interrupts", i);
-			data += ETH_GSTRING_LEN;
-		}
-		break;
+		snprintf(data, ETH_GSTRING_LEN, "tx%d_bytes", i);
+		data += ETH_GSTRING_LEN;
 
-	case ETH_SS_PRIV_FLAGS:
-		for (i = 0; i < ARRAY_SIZE(ibmvnic_priv_flags); i++)
-			strcpy(data + i * ETH_GSTRING_LEN,
-			       ibmvnic_priv_flags[i]);
-		break;
-	default:
-		return;
+		snprintf(data, ETH_GSTRING_LEN, "tx%d_dropped_packets", i);
+		data += ETH_GSTRING_LEN;
+	}
+
+	for (i = 0; i < adapter->req_rx_queues; i++) {
+		snprintf(data, ETH_GSTRING_LEN, "rx%d_packets", i);
+		data += ETH_GSTRING_LEN;
+
+		snprintf(data, ETH_GSTRING_LEN, "rx%d_bytes", i);
+		data += ETH_GSTRING_LEN;
+
+		snprintf(data, ETH_GSTRING_LEN, "rx%d_interrupts", i);
+		data += ETH_GSTRING_LEN;
 	}
 }
 
@@ -3039,8 +3158,6 @@
 		return ARRAY_SIZE(ibmvnic_stats) +
 		       adapter->req_tx_queues * NUM_TX_STATS +
 		       adapter->req_rx_queues * NUM_RX_STATS;
-	case ETH_SS_PRIV_FLAGS:
-		return ARRAY_SIZE(ibmvnic_priv_flags);
 	default:
 		return -EOPNOTSUPP;
 	}
@@ -3093,26 +3210,6 @@
 	}
 }
 
-static u32 ibmvnic_get_priv_flags(struct net_device *netdev)
-{
-	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
-
-	return adapter->priv_flags;
-}
-
-static int ibmvnic_set_priv_flags(struct net_device *netdev, u32 flags)
-{
-	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
-	bool which_maxes = !!(flags & IBMVNIC_USE_SERVER_MAXES);
-
-	if (which_maxes)
-		adapter->priv_flags |= IBMVNIC_USE_SERVER_MAXES;
-	else
-		adapter->priv_flags &= ~IBMVNIC_USE_SERVER_MAXES;
-
-	return 0;
-}
-
 static const struct ethtool_ops ibmvnic_ethtool_ops = {
 	.get_drvinfo		= ibmvnic_get_drvinfo,
 	.get_msglevel		= ibmvnic_get_msglevel,
@@ -3126,8 +3223,6 @@
 	.get_sset_count         = ibmvnic_get_sset_count,
 	.get_ethtool_stats	= ibmvnic_get_ethtool_stats,
 	.get_link_ksettings	= ibmvnic_get_link_ksettings,
-	.get_priv_flags		= ibmvnic_get_priv_flags,
-	.set_priv_flags		= ibmvnic_set_priv_flags,
 };
 
 /* Routines for managing CRQs/sCRQs  */
@@ -3326,6 +3421,12 @@
 		adapter->num_active_tx_scrqs = 0;
 	}
 
+	/* Clean any remaining outstanding SKBs
+	 * we freed the irq so we won't be hearing
+	 * from them
+	 */
+	clean_tx_pools(adapter);
+
 	if (adapter->rx_scrq) {
 		for (i = 0; i < adapter->num_active_rx_scrqs; i++) {
 			if (!adapter->rx_scrq[i])
@@ -3456,9 +3557,15 @@
 		    (adapter->req_tx_entries_per_subcrq / 2) &&
 		    __netif_subqueue_stopped(adapter->netdev,
 					     scrq->pool_index)) {
-			netif_wake_subqueue(adapter->netdev, scrq->pool_index);
-			netdev_dbg(adapter->netdev, "Started queue %d\n",
-				   scrq->pool_index);
+			rcu_read_lock();
+			if (adapter->tx_queues_active) {
+				netif_wake_subqueue(adapter->netdev,
+						    scrq->pool_index);
+				netdev_dbg(adapter->netdev,
+					   "Started queue %d\n",
+					   scrq->pool_index);
+			}
+			rcu_read_unlock();
 		}
 	}
 
@@ -3664,11 +3771,25 @@
 	struct device *dev = &adapter->vdev->dev;
 	union ibmvnic_crq crq;
 	int max_entries;
+	int cap_reqs;
+
+	/* We send out 6 or 7 REQUEST_CAPABILITY CRQs below (depending on
+	 * the PROMISC flag). Initialize this count upfront. When the tasklet
+	 * receives a response to all of these, it will send the next protocol
+	 * message (QUERY_IP_OFFLOAD).
+	 */
+	if (!(adapter->netdev->flags & IFF_PROMISC) ||
+	    adapter->promisc_supported)
+		cap_reqs = 7;
+	else
+		cap_reqs = 6;
 
 	if (!retry) {
 		/* Sub-CRQ entries are 32 byte long */
 		int entries_page = 4 * PAGE_SIZE / (sizeof(u64) * 4);
 
+		atomic_set(&adapter->running_cap_crqs, cap_reqs);
+
 		if (adapter->min_tx_entries_per_subcrq > entries_page ||
 		    adapter->min_rx_add_entries_per_subcrq > entries_page) {
 			dev_err(dev, "Fatal, invalid entries per sub-crq\n");
@@ -3729,44 +3850,45 @@
 					adapter->opt_rx_comp_queues;
 
 		adapter->req_rx_add_queues = adapter->max_rx_add_queues;
+	} else {
+		atomic_add(cap_reqs, &adapter->running_cap_crqs);
 	}
-
 	memset(&crq, 0, sizeof(crq));
 	crq.request_capability.first = IBMVNIC_CRQ_CMD;
 	crq.request_capability.cmd = REQUEST_CAPABILITY;
 
 	crq.request_capability.capability = cpu_to_be16(REQ_TX_QUEUES);
 	crq.request_capability.number = cpu_to_be64(adapter->req_tx_queues);
-	atomic_inc(&adapter->running_cap_crqs);
+	cap_reqs--;
 	ibmvnic_send_crq(adapter, &crq);
 
 	crq.request_capability.capability = cpu_to_be16(REQ_RX_QUEUES);
 	crq.request_capability.number = cpu_to_be64(adapter->req_rx_queues);
-	atomic_inc(&adapter->running_cap_crqs);
+	cap_reqs--;
 	ibmvnic_send_crq(adapter, &crq);
 
 	crq.request_capability.capability = cpu_to_be16(REQ_RX_ADD_QUEUES);
 	crq.request_capability.number = cpu_to_be64(adapter->req_rx_add_queues);
-	atomic_inc(&adapter->running_cap_crqs);
+	cap_reqs--;
 	ibmvnic_send_crq(adapter, &crq);
 
 	crq.request_capability.capability =
 	    cpu_to_be16(REQ_TX_ENTRIES_PER_SUBCRQ);
 	crq.request_capability.number =
 	    cpu_to_be64(adapter->req_tx_entries_per_subcrq);
-	atomic_inc(&adapter->running_cap_crqs);
+	cap_reqs--;
 	ibmvnic_send_crq(adapter, &crq);
 
 	crq.request_capability.capability =
 	    cpu_to_be16(REQ_RX_ADD_ENTRIES_PER_SUBCRQ);
 	crq.request_capability.number =
 	    cpu_to_be64(adapter->req_rx_add_entries_per_subcrq);
-	atomic_inc(&adapter->running_cap_crqs);
+	cap_reqs--;
 	ibmvnic_send_crq(adapter, &crq);
 
 	crq.request_capability.capability = cpu_to_be16(REQ_MTU);
 	crq.request_capability.number = cpu_to_be64(adapter->req_mtu);
-	atomic_inc(&adapter->running_cap_crqs);
+	cap_reqs--;
 	ibmvnic_send_crq(adapter, &crq);
 
 	if (adapter->netdev->flags & IFF_PROMISC) {
@@ -3774,16 +3896,21 @@
 			crq.request_capability.capability =
 			    cpu_to_be16(PROMISC_REQUESTED);
 			crq.request_capability.number = cpu_to_be64(1);
-			atomic_inc(&adapter->running_cap_crqs);
+			cap_reqs--;
 			ibmvnic_send_crq(adapter, &crq);
 		}
 	} else {
 		crq.request_capability.capability =
 		    cpu_to_be16(PROMISC_REQUESTED);
 		crq.request_capability.number = cpu_to_be64(0);
-		atomic_inc(&adapter->running_cap_crqs);
+		cap_reqs--;
 		ibmvnic_send_crq(adapter, &crq);
 	}
+
+	/* Keep at end to catch any discrepancy between expected and actual
+	 * CRQs sent.
+	 */
+	WARN_ON(cap_reqs != 0);
 }
 
 static int pending_scrq(struct ibmvnic_adapter *adapter,
@@ -4121,11 +4248,14 @@
 	if (rc) {
 		adapter->login_pending = false;
 		netdev_err(adapter->netdev, "Failed to send login, rc=%d\n", rc);
-		goto buf_rsp_map_failed;
+		goto buf_send_failed;
 	}
 
 	return 0;
 
+buf_send_failed:
+	dma_unmap_single(dev, rsp_buffer_token, rsp_buffer_size,
+			 DMA_FROM_DEVICE);
 buf_rsp_map_failed:
 	kfree(login_rsp_buffer);
 	adapter->login_rsp_buf = NULL;
@@ -4177,118 +4307,132 @@
 static void send_query_cap(struct ibmvnic_adapter *adapter)
 {
 	union ibmvnic_crq crq;
+	int cap_reqs;
+
+	/* We send out 25 QUERY_CAPABILITY CRQs below.  Initialize this count
+	 * upfront. When the tasklet receives a response to all of these, it
+	 * can send out the next protocol messaage (REQUEST_CAPABILITY).
+	 */
+	cap_reqs = 25;
+
+	atomic_set(&adapter->running_cap_crqs, cap_reqs);
 
-	atomic_set(&adapter->running_cap_crqs, 0);
 	memset(&crq, 0, sizeof(crq));
 	crq.query_capability.first = IBMVNIC_CRQ_CMD;
 	crq.query_capability.cmd = QUERY_CAPABILITY;
 
 	crq.query_capability.capability = cpu_to_be16(MIN_TX_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MIN_RX_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MIN_RX_ADD_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MAX_TX_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MAX_RX_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MAX_RX_ADD_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 	    cpu_to_be16(MIN_TX_ENTRIES_PER_SUBCRQ);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 	    cpu_to_be16(MIN_RX_ADD_ENTRIES_PER_SUBCRQ);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 	    cpu_to_be16(MAX_TX_ENTRIES_PER_SUBCRQ);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 	    cpu_to_be16(MAX_RX_ADD_ENTRIES_PER_SUBCRQ);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(TCP_IP_OFFLOAD);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(PROMISC_SUPPORTED);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MIN_MTU);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MAX_MTU);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MAX_MULTICAST_FILTERS);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(VLAN_HEADER_INSERTION);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(RX_VLAN_HEADER_INSERTION);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(MAX_TX_SG_ENTRIES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(RX_SG_SUPPORTED);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(OPT_TX_COMP_SUB_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(OPT_RX_COMP_QUEUES);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 			cpu_to_be16(OPT_RX_BUFADD_Q_PER_RX_COMP_Q);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 			cpu_to_be16(OPT_TX_ENTRIES_PER_SUBCRQ);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability =
 			cpu_to_be16(OPT_RXBA_ENTRIES_PER_SUBCRQ);
-	atomic_inc(&adapter->running_cap_crqs);
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
 
 	crq.query_capability.capability = cpu_to_be16(TX_RX_DESC_REQ);
-	atomic_inc(&adapter->running_cap_crqs);
+
 	ibmvnic_send_crq(adapter, &crq);
+	cap_reqs--;
+
+	/* Keep at end to catch any discrepancy between expected and actual
+	 * CRQs sent.
+	 */
+	WARN_ON(cap_reqs != 0);
 }
 
 static void send_query_ip_offload(struct ibmvnic_adapter *adapter)
@@ -4576,8 +4720,7 @@
 	/* crq->change_mac_addr.mac_addr is the requested one
 	 * crq->change_mac_addr_rsp.mac_addr is the returned valid one.
 	 */
-	ether_addr_copy(netdev->dev_addr,
-			&crq->change_mac_addr_rsp.mac_addr[0]);
+	eth_hw_addr_set(netdev, &crq->change_mac_addr_rsp.mac_addr[0]);
 	ether_addr_copy(adapter->mac_addr,
 			&crq->change_mac_addr_rsp.mac_addr[0]);
 out:
@@ -4593,6 +4736,8 @@
 	char *name;
 
 	atomic_dec(&adapter->running_cap_crqs);
+	netdev_dbg(adapter->netdev, "Outstanding request-caps: %d\n",
+		   atomic_read(&adapter->running_cap_crqs));
 	switch (be16_to_cpu(crq->request_capability_rsp.capability)) {
 	case REQ_TX_QUEUES:
 		req_value = &adapter->req_tx_queues;
@@ -4674,6 +4819,7 @@
 	int num_tx_pools;
 	int num_rx_pools;
 	u64 *size_array;
+	u32 rsp_len;
 	int i;
 
 	/* CHECK: Test/set of login_pending does not need to be atomic
@@ -4685,11 +4831,6 @@
 	}
 	adapter->login_pending = false;
 
-	dma_unmap_single(dev, adapter->login_buf_token, adapter->login_buf_sz,
-			 DMA_TO_DEVICE);
-	dma_unmap_single(dev, adapter->login_rsp_buf_token,
-			 adapter->login_rsp_buf_sz, DMA_FROM_DEVICE);
-
 	/* If the number of queues requested can't be allocated by the
 	 * server, the login response will return with code 1. We will need
 	 * to resend the login buffer with fewer queues requested.
@@ -4725,6 +4866,23 @@
 		ibmvnic_reset(adapter, VNIC_RESET_FATAL);
 		return -EIO;
 	}
+
+	rsp_len = be32_to_cpu(login_rsp->len);
+	if (be32_to_cpu(login->login_rsp_len) < rsp_len ||
+	    rsp_len <= be32_to_cpu(login_rsp->off_txsubm_subcrqs) ||
+	    rsp_len <= be32_to_cpu(login_rsp->off_rxadd_subcrqs) ||
+	    rsp_len <= be32_to_cpu(login_rsp->off_rxadd_buff_size) ||
+	    rsp_len <= be32_to_cpu(login_rsp->off_supp_tx_desc)) {
+		/* This can happen if a login request times out and there are
+		 * 2 outstanding login requests sent, the LOGIN_RSP crq
+		 * could have been for the older login request. So we are
+		 * parsing the newer response buffer which may be incomplete
+		 */
+		dev_err(dev, "FATAL: Login rsp offsets/lengths invalid\n");
+		ibmvnic_reset(adapter, VNIC_RESET_FATAL);
+		return -EIO;
+	}
+
 	size_array = (u64 *)((u8 *)(adapter->login_rsp_buf) +
 		be32_to_cpu(adapter->login_rsp_buf->off_rxadd_buff_size));
 	/* variable buffer sizes are not supported, so just read the
@@ -5069,11 +5227,6 @@
 			 */
 			adapter->login_pending = false;
 
-			if (!completion_done(&adapter->init_done)) {
-				complete(&adapter->init_done);
-				adapter->init_done_rc = -EIO;
-			}
-
 			if (adapter->state == VNIC_DOWN)
 				rc = ibmvnic_reset(adapter, VNIC_RESET_PASSIVE_INIT);
 			else
@@ -5094,6 +5247,13 @@
 					   rc);
 				adapter->failover_pending = false;
 			}
+
+			if (!completion_done(&adapter->init_done)) {
+				if (!adapter->init_done_rc)
+					adapter->init_done_rc = -EAGAIN;
+				complete(&adapter->init_done);
+			}
+
 			break;
 		case IBMVNIC_CRQ_INIT_COMPLETE:
 			dev_info(dev, "Partner initialization complete\n");
@@ -5114,6 +5274,13 @@
 			adapter->fw_done_rc = -EIO;
 			complete(&adapter->fw_done);
 		}
+
+		/* if we got here during crq-init, retry crq-init */
+		if (!completion_done(&adapter->init_done)) {
+			adapter->init_done_rc = -EAGAIN;
+			complete(&adapter->init_done);
+		}
+
 		if (!completion_done(&adapter->stats_done))
 			complete(&adapter->stats_done);
 		if (test_bit(0, &adapter->resetting))
@@ -5268,12 +5435,6 @@
 			ibmvnic_handle_crq(crq, adapter);
 			crq->generic.first = 0;
 		}
-
-		/* remain in tasklet until all
-		 * capabilities responses are received
-		 */
-		if (!adapter->wait_capability)
-			done = true;
 	}
 	/* if capabilities CRQ's were sent in this tasklet, the following
 	 * tasklet must wait until all responses are received
@@ -5414,6 +5575,9 @@
 	crq->cur = 0;
 	spin_lock_init(&crq->lock);
 
+	/* process any CRQs that were queued before we enabled interrupts */
+	tasklet_schedule(&adapter->tasklet);
+
 	return retrc;
 
 req_irq_failed:
@@ -5439,10 +5603,6 @@
 
 	adapter->from_passive_init = false;
 
-	if (reset)
-		reinit_completion(&adapter->init_done);
-
-	adapter->init_done_rc = 0;
 	rc = ibmvnic_send_crq_init(adapter);
 	if (rc) {
 		dev_err(dev, "Send crq init failed with error %d\n", rc);
@@ -5456,12 +5616,14 @@
 
 	if (adapter->init_done_rc) {
 		release_crq_queue(adapter);
+		dev_err(dev, "CRQ-init failed, %d\n", adapter->init_done_rc);
 		return adapter->init_done_rc;
 	}
 
 	if (adapter->from_passive_init) {
 		adapter->state = VNIC_OPEN;
 		adapter->from_passive_init = false;
+		dev_err(dev, "CRQ-init failed, passive-init\n");
 		return -1;
 	}
 
@@ -5473,6 +5635,15 @@
 			release_sub_crqs(adapter, 0);
 			rc = init_sub_crqs(adapter);
 		} else {
+			/* no need to reinitialize completely, but we do
+			 * need to clean up transmits that were in flight
+			 * when we processed the reset.  Failure to do so
+			 * will confound the upper layer, usually TCP, by
+			 * creating the illusion of transmits that are
+			 * awaiting completion.
+			 */
+			clean_tx_pools(adapter);
+
 			rc = reset_sub_crq_queues(adapter);
 		}
 	} else {
@@ -5501,6 +5672,7 @@
 	struct ibmvnic_adapter *adapter;
 	struct net_device *netdev;
 	unsigned char *mac_addr_p;
+	unsigned long flags;
 	bool init_success;
 	int rc;
 
@@ -5529,7 +5701,7 @@
 	adapter->login_pending = false;
 
 	ether_addr_copy(adapter->mac_addr, mac_addr_p);
-	ether_addr_copy(netdev->dev_addr, adapter->mac_addr);
+	eth_hw_addr_set(netdev, adapter->mac_addr);
 	netdev->irq = dev->irq;
 	netdev->netdev_ops = &ibmvnic_netdev_ops;
 	netdev->ethtool_ops = &ibmvnic_ethtool_ops;
@@ -5542,6 +5714,7 @@
 	spin_lock_init(&adapter->rwi_lock);
 	spin_lock_init(&adapter->state_lock);
 	mutex_init(&adapter->fw_lock);
+	init_completion(&adapter->probe_done);
 	init_completion(&adapter->init_done);
 	init_completion(&adapter->fw_done);
 	init_completion(&adapter->reset_done);
@@ -5550,6 +5723,33 @@
 
 	init_success = false;
 	do {
+		reinit_init_done(adapter);
+
+		/* clear any failovers we got in the previous pass
+		 * since we are reinitializing the CRQ
+		 */
+		adapter->failover_pending = false;
+
+		/* If we had already initialized CRQ, we may have one or
+		 * more resets queued already. Discard those and release
+		 * the CRQ before initializing the CRQ again.
+		 */
+		release_crq_queue(adapter);
+
+		/* Since we are still in PROBING state, __ibmvnic_reset()
+		 * will not access the ->rwi_list and since we released CRQ,
+		 * we won't get _new_ transport events. But there maybe an
+		 * ongoing ibmvnic_reset() call. So serialize access to
+		 * rwi_list. If we win the race, ibvmnic_reset() could add
+		 * a reset after we purged but thats ok - we just may end
+		 * up with an extra reset (i.e similar to having two or more
+		 * resets in the queue at once).
+		 * CHECK.
+		 */
+		spin_lock_irqsave(&adapter->rwi_lock, flags);
+		flush_reset_queue(adapter);
+		spin_unlock_irqrestore(&adapter->rwi_lock, flags);
+
 		rc = init_crq_queue(adapter);
 		if (rc) {
 			dev_err(&dev->dev, "Couldn't initialize crq. rc=%d\n",
@@ -5558,7 +5758,7 @@
 		}
 
 		rc = ibmvnic_reset_init(adapter, false);
-	} while (rc == EAGAIN);
+	} while (rc == -EAGAIN);
 
 	/* We are ignoring the error from ibmvnic_reset_init() assuming that the
 	 * partner is not ready. CRQ is not active. When the partner becomes
@@ -5581,12 +5781,6 @@
 		goto ibmvnic_dev_file_err;
 
 	netif_carrier_off(netdev);
-	rc = register_netdev(netdev);
-	if (rc) {
-		dev_err(&dev->dev, "failed to register netdev rc=%d\n", rc);
-		goto ibmvnic_register_fail;
-	}
-	dev_info(&dev->dev, "ibmvnic registered\n");
 
 	if (init_success) {
 		adapter->state = VNIC_PROBED;
@@ -5599,6 +5793,16 @@
 
 	adapter->wait_for_reset = false;
 	adapter->last_reset_time = jiffies;
+
+	rc = register_netdev(netdev);
+	if (rc) {
+		dev_err(&dev->dev, "failed to register netdev rc=%d\n", rc);
+		goto ibmvnic_register_fail;
+	}
+	dev_info(&dev->dev, "ibmvnic registered\n");
+
+	complete(&adapter->probe_done);
+
 	return 0;
 
 ibmvnic_register_fail:
@@ -5613,6 +5817,17 @@
 ibmvnic_init_fail:
 	release_sub_crqs(adapter, 1);
 	release_crq_queue(adapter);
+
+	/* cleanup worker thread after releasing CRQ so we don't get
+	 * transport events (i.e new work items for the worker thread).
+	 */
+	adapter->state = VNIC_REMOVING;
+	complete(&adapter->probe_done);
+	flush_work(&adapter->ibmvnic_reset);
+	flush_delayed_work(&adapter->ibmvnic_delayed_reset);
+
+	flush_reset_queue(adapter);
+
 	mutex_destroy(&adapter->fw_lock);
 	free_netdev(netdev);
 
@@ -5687,10 +5902,14 @@
 		   be64_to_cpu(session_token));
 	rc = plpar_hcall_norets(H_VIOCTL, adapter->vdev->unit_address,
 				H_SESSION_ERR_DETECTED, session_token, 0, 0);
-	if (rc)
+	if (rc) {
 		netdev_err(netdev,
 			   "H_VIOCTL initiated failover failed, rc %ld\n",
 			   rc);
+		goto last_resort;
+	}
+
+	return count;
 
 last_resort:
 	netdev_dbg(netdev, "Trying to send CRQ_CMD, the last resort\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ibm/ibmvnic.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ibm/ibmvnic.h
@@ -43,11 +43,6 @@
 
 #define IBMVNIC_RESET_DELAY 100
 
-static const char ibmvnic_priv_flags[][ETH_GSTRING_LEN] = {
-#define IBMVNIC_USE_SERVER_MAXES 0x1
-	"use-server-maxes"
-};
-
 struct ibmvnic_login_buffer {
 	__be32 len;
 	__be32 version;
@@ -885,7 +880,6 @@
 	struct ibmvnic_control_ip_offload_buffer ip_offload_ctrl;
 	dma_addr_t ip_offload_ctrl_tok;
 	u32 msg_enable;
-	u32 priv_flags;
 
 	/* Vital Product Data (VPD) */
 	struct ibmvnic_vpd *vpd;
@@ -933,6 +927,7 @@
 
 	struct ibmvnic_tx_pool *tx_pool;
 	struct ibmvnic_tx_pool *tso_pool;
+	struct completion probe_done;
 	struct completion init_done;
 	int init_done_rc;
 
@@ -1002,11 +997,14 @@
 	struct work_struct ibmvnic_reset;
 	struct delayed_work ibmvnic_delayed_reset;
 	unsigned long resetting;
-	bool napi_enabled, from_passive_init;
-	bool login_pending;
 	/* last device reset time */
 	unsigned long last_reset_time;
 
+	bool napi_enabled;
+	bool from_passive_init;
+	bool login_pending;
+	/* protected by rcu */
+	bool tx_queues_active;
 	bool failover_pending;
 	bool force_reset_recovery;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/e100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/e100.c
@@ -1742,11 +1742,8 @@
 	dma_addr = dma_map_single(&nic->pdev->dev, skb->data, skb->len,
 				  DMA_TO_DEVICE);
 	/* If we can't map the skb, have the upper layer try later */
-	if (dma_mapping_error(&nic->pdev->dev, dma_addr)) {
-		dev_kfree_skb_any(skb);
-		skb = NULL;
+	if (dma_mapping_error(&nic->pdev->dev, dma_addr))
 		return -ENOMEM;
-	}
 
 	/*
 	 * Use the last 4 bytes of the SKB payload packet as the CRC, used for
@@ -3003,9 +3000,10 @@
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct nic *nic = netdev_priv(netdev);
 
+	netif_device_detach(netdev);
+
 	if (netif_running(netdev))
 		e100_down(nic);
-	netif_device_detach(netdev);
 
 	if ((nic->flags & wol_magic) | e100_asf(nic)) {
 		/* enable reverse auto-negotiation */
@@ -3022,7 +3020,7 @@
 		*enable_wake = false;
 	}
 
-	pci_clear_master(pdev);
+	pci_disable_device(pdev);
 }
 
 static int __e100_power_off(struct pci_dev *pdev, bool wake)
@@ -3042,8 +3040,6 @@
 
 	__e100_shutdown(to_pci_dev(dev_d), &wake);
 
-	device_wakeup_disable(dev_d);
-
 	return 0;
 }
 
@@ -3051,6 +3047,14 @@
 {
 	struct net_device *netdev = dev_get_drvdata(dev_d);
 	struct nic *nic = netdev_priv(netdev);
+	int err;
+
+	err = pci_enable_device(to_pci_dev(dev_d));
+	if (err) {
+		netdev_err(netdev, "Resume cannot enable PCI device, aborting\n");
+		return err;
+	}
+	pci_set_master(to_pci_dev(dev_d));
 
 	/* disable reverse auto-negotiation */
 	if (nic->phy == phy_82552_v) {
@@ -3062,10 +3066,11 @@
 		           smartspeed & ~(E100_82552_REV_ANEG));
 	}
 
-	netif_device_attach(netdev);
 	if (netif_running(netdev))
 		e100_up(nic);
 
+	netif_device_attach(netdev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/e1000e/e1000.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -114,7 +114,8 @@
 	board_pch_lpt,
 	board_pch_spt,
 	board_pch_cnp,
-	board_pch_tgp
+	board_pch_tgp,
+	board_pch_adp
 };
 
 struct e1000_ps_page {
@@ -501,6 +502,7 @@
 extern const struct e1000_info e1000_pch_spt_info;
 extern const struct e1000_info e1000_pch_cnp_info;
 extern const struct e1000_info e1000_pch_tgp_info;
+extern const struct e1000_info e1000_pch_adp_info;
 extern const struct e1000_info e1000_es2_info;
 
 void e1000e_ptp_init(struct e1000_adapter *adapter);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -1009,8 +1009,8 @@
 {
 	u32 reg = link << (E1000_LTRV_REQ_SHIFT + E1000_LTRV_NOSNOOP_SHIFT) |
 	    link << E1000_LTRV_REQ_SHIFT | E1000_LTRV_SEND;
-	u16 max_ltr_enc_d = 0;	/* maximum LTR decoded by platform */
-	u16 lat_enc_d = 0;	/* latency decoded */
+	u32 max_ltr_enc_d = 0;	/* maximum LTR decoded by platform */
+	u32 lat_enc_d = 0;	/* latency decoded */
 	u16 lat_enc = 0;	/* latency encoded */
 
 	if (link) {
@@ -4136,9 +4136,9 @@
 		return ret_val;
 
 	if (!(data & valid_csum_mask)) {
-		e_dbg("NVM Checksum Invalid\n");
+		e_dbg("NVM Checksum valid bit not set\n");
 
-		if (hw->mac.type < e1000_pch_cnp) {
+		if (hw->mac.type < e1000_pch_tgp) {
 			data |= valid_csum_mask;
 			ret_val = e1000_write_nvm(hw, word, 1, &data);
 			if (ret_val)
@@ -6007,6 +6007,26 @@
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
 				  | FLAG_HAS_HW_TIMESTAMP
+				  | FLAG_HAS_CTRLEXT_ON_LOAD
+				  | FLAG_HAS_AMT
+				  | FLAG_HAS_FLASH
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_APME_IN_WUC,
+	.flags2			= FLAG2_HAS_PHY_STATS
+				  | FLAG2_HAS_EEE,
+	.pba			= 26,
+	.max_hw_frame_size	= 9022,
+	.get_variants		= e1000_get_variants_ich8lan,
+	.mac_ops		= &ich8_mac_ops,
+	.phy_ops		= &ich8_phy_ops,
+	.nvm_ops		= &spt_nvm_ops,
+};
+
+const struct e1000_info e1000_pch_adp_info = {
+	.mac			= e1000_pch_adp,
+	.flags			= FLAG_IS_ICH
+				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/e1000e/netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -52,6 +52,7 @@
 	[board_pch_spt]		= &e1000_pch_spt_info,
 	[board_pch_cnp]		= &e1000_pch_cnp_info,
 	[board_pch_tgp]		= &e1000_pch_tgp_info,
+	[board_pch_adp]		= &e1000_pch_adp_info,
 };
 
 struct e1000_reg_info {
@@ -5297,31 +5298,6 @@
 				ew32(TARC(0), tarc0);
 			}
 
-			/* disable TSO for pcie and 10/100 speeds, to avoid
-			 * some hardware issues
-			 */
-			if (!(adapter->flags & FLAG_TSO_FORCE)) {
-				switch (adapter->link_speed) {
-				case SPEED_10:
-				case SPEED_100:
-					e_info("10/100 speed: disabling TSO\n");
-					netdev->features &= ~NETIF_F_TSO;
-					netdev->features &= ~NETIF_F_TSO6;
-					break;
-				case SPEED_1000:
-					netdev->features |= NETIF_F_TSO;
-					netdev->features |= NETIF_F_TSO6;
-					break;
-				default:
-					/* oops */
-					break;
-				}
-				if (hw->mac.type == e1000_pch_spt) {
-					netdev->features &= ~NETIF_F_TSO;
-					netdev->features &= ~NETIF_F_TSO6;
-				}
-			}
-
 			/* enable transmits in the hardware, need to do this
 			 * after setting TARC(0)
 			 */
@@ -5940,9 +5916,9 @@
 		e1000_tx_queue(tx_ring, tx_flags, count);
 		/* Make sure there is space in the ring for the next send. */
 		e1000_maybe_stop_tx(tx_ring,
-				    (MAX_SKB_FRAGS *
+				    ((MAX_SKB_FRAGS + 1) *
 				     DIV_ROUND_UP(PAGE_SIZE,
-						  adapter->tx_fifo_limit) + 2));
+						  adapter->tx_fifo_limit) + 4));
 
 		if (!netdev_xmit_more() ||
 		    netif_xmit_stopped(netdev_get_tx_queue(netdev, 0))) {
@@ -6346,7 +6322,8 @@
 	u32 mac_data;
 	u16 phy_data;
 
-	if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) {
+	if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID &&
+	    hw->mac.type >= e1000_pch_adp) {
 		/* Request ME configure the device for S0ix */
 		mac_data = er32(H2ME);
 		mac_data |= E1000_H2ME_START_DPG;
@@ -6397,49 +6374,49 @@
 		mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG;
 		ew32(EXTCNF_CTRL, mac_data);
 
-		/* Enable the Dynamic Power Gating in the MAC */
-		mac_data = er32(FEXTNVM7);
-		mac_data |= BIT(22);
-		ew32(FEXTNVM7, mac_data);
-
 		/* Disable disconnected cable conditioning for Power Gating */
 		mac_data = er32(DPGFR);
 		mac_data |= BIT(2);
 		ew32(DPGFR, mac_data);
 
-		/* Don't wake from dynamic Power Gating with clock request */
-		mac_data = er32(FEXTNVM12);
-		mac_data |= BIT(12);
-		ew32(FEXTNVM12, mac_data);
-
-		/* Ungate PGCB clock */
-		mac_data = er32(FEXTNVM9);
-		mac_data &= ~BIT(28);
-		ew32(FEXTNVM9, mac_data);
-
-		/* Enable K1 off to enable mPHY Power Gating */
-		mac_data = er32(FEXTNVM6);
-		mac_data |= BIT(31);
-		ew32(FEXTNVM6, mac_data);
-
-		/* Enable mPHY power gating for any link and speed */
-		mac_data = er32(FEXTNVM8);
-		mac_data |= BIT(9);
-		ew32(FEXTNVM8, mac_data);
-
 		/* Enable the Dynamic Clock Gating in the DMA and MAC */
 		mac_data = er32(CTRL_EXT);
 		mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN;
 		ew32(CTRL_EXT, mac_data);
-
-		/* No MAC DPG gating SLP_S0 in modern standby
-		 * Switch the logic of the lanphypc to use PMC counter
-		 */
-		mac_data = er32(FEXTNVM5);
-		mac_data |= BIT(7);
-		ew32(FEXTNVM5, mac_data);
 	}
 
+	/* Enable the Dynamic Power Gating in the MAC */
+	mac_data = er32(FEXTNVM7);
+	mac_data |= BIT(22);
+	ew32(FEXTNVM7, mac_data);
+
+	/* Don't wake from dynamic Power Gating with clock request */
+	mac_data = er32(FEXTNVM12);
+	mac_data |= BIT(12);
+	ew32(FEXTNVM12, mac_data);
+
+	/* Ungate PGCB clock */
+	mac_data = er32(FEXTNVM9);
+	mac_data &= ~BIT(28);
+	ew32(FEXTNVM9, mac_data);
+
+	/* Enable K1 off to enable mPHY Power Gating */
+	mac_data = er32(FEXTNVM6);
+	mac_data |= BIT(31);
+	ew32(FEXTNVM6, mac_data);
+
+	/* Enable mPHY power gating for any link and speed */
+	mac_data = er32(FEXTNVM8);
+	mac_data |= BIT(9);
+	ew32(FEXTNVM8, mac_data);
+
+	/* No MAC DPG gating SLP_S0 in modern standby
+	 * Switch the logic of the lanphypc to use PMC counter
+	 */
+	mac_data = er32(FEXTNVM5);
+	mac_data |= BIT(7);
+	ew32(FEXTNVM5, mac_data);
+
 	/* Disable the time synchronization clock */
 	mac_data = er32(FEXTNVM7);
 	mac_data |= BIT(31);
@@ -6495,7 +6472,12 @@
 	u16 phy_data;
 	u32 i = 0;
 
-	if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) {
+	if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID &&
+	    hw->mac.type >= e1000_pch_adp) {
+		/* Keep the GPT clock enabled for CSME */
+		mac_data = er32(FEXTNVM);
+		mac_data |= BIT(3);
+		ew32(FEXTNVM, mac_data);
 		/* Request ME unconfigure the device from S0ix */
 		mac_data = er32(H2ME);
 		mac_data &= ~E1000_H2ME_START_DPG;
@@ -6526,33 +6508,6 @@
 	} else {
 		/* Request driver unconfigure the device from S0ix */
 
-		/* Disable the Dynamic Power Gating in the MAC */
-		mac_data = er32(FEXTNVM7);
-		mac_data &= 0xFFBFFFFF;
-		ew32(FEXTNVM7, mac_data);
-
-		/* Disable mPHY power gating for any link and speed */
-		mac_data = er32(FEXTNVM8);
-		mac_data &= ~BIT(9);
-		ew32(FEXTNVM8, mac_data);
-
-		/* Disable K1 off */
-		mac_data = er32(FEXTNVM6);
-		mac_data &= ~BIT(31);
-		ew32(FEXTNVM6, mac_data);
-
-		/* Disable Ungate PGCB clock */
-		mac_data = er32(FEXTNVM9);
-		mac_data |= BIT(28);
-		ew32(FEXTNVM9, mac_data);
-
-		/* Cancel not waking from dynamic
-		 * Power Gating with clock request
-		 */
-		mac_data = er32(FEXTNVM12);
-		mac_data &= ~BIT(12);
-		ew32(FEXTNVM12, mac_data);
-
 		/* Cancel disable disconnected cable conditioning
 		 * for Power Gating
 		 */
@@ -6565,13 +6520,6 @@
 		mac_data &= 0xFFF7FFFF;
 		ew32(CTRL_EXT, mac_data);
 
-		/* Revert the lanphypc logic to use the internal Gbe counter
-		 * and not the PMC counter
-		 */
-		mac_data = er32(FEXTNVM5);
-		mac_data &= 0xFFFFFF7F;
-		ew32(FEXTNVM5, mac_data);
-
 		/* Enable the periodic inband message,
 		 * Request PCIe clock in K1 page770_17[10:9] =01b
 		 */
@@ -6609,6 +6557,40 @@
 	mac_data &= ~BIT(31);
 	mac_data |= BIT(0);
 	ew32(FEXTNVM7, mac_data);
+
+	/* Disable the Dynamic Power Gating in the MAC */
+	mac_data = er32(FEXTNVM7);
+	mac_data &= 0xFFBFFFFF;
+	ew32(FEXTNVM7, mac_data);
+
+	/* Disable mPHY power gating for any link and speed */
+	mac_data = er32(FEXTNVM8);
+	mac_data &= ~BIT(9);
+	ew32(FEXTNVM8, mac_data);
+
+	/* Disable K1 off */
+	mac_data = er32(FEXTNVM6);
+	mac_data &= ~BIT(31);
+	ew32(FEXTNVM6, mac_data);
+
+	/* Disable Ungate PGCB clock */
+	mac_data = er32(FEXTNVM9);
+	mac_data |= BIT(28);
+	ew32(FEXTNVM9, mac_data);
+
+	/* Cancel not waking from dynamic
+	 * Power Gating with clock request
+	 */
+	mac_data = er32(FEXTNVM12);
+	mac_data &= ~BIT(12);
+	ew32(FEXTNVM12, mac_data);
+
+	/* Revert the lanphypc logic to use the internal Gbe counter
+	 * and not the PMC counter
+	 */
+	mac_data = er32(FEXTNVM5);
+	mac_data &= 0xFFFFFF7F;
+	ew32(FEXTNVM5, mac_data);
 }
 
 static int e1000e_pm_freeze(struct device *dev)
@@ -7048,6 +7030,8 @@
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	int rc;
 
+	pdev->pme_poll = true;
+
 	rc = __e1000_resume(pdev);
 	if (rc)
 		return rc;
@@ -7536,6 +7520,32 @@
 			    NETIF_F_RXCSUM |
 			    NETIF_F_HW_CSUM);
 
+	/* disable TSO for pcie and 10/100 speeds to avoid
+	 * some hardware issues and for i219 to fix transfer
+	 * speed being capped at 60%
+	 */
+	if (!(adapter->flags & FLAG_TSO_FORCE)) {
+		switch (adapter->link_speed) {
+		case SPEED_10:
+		case SPEED_100:
+			e_info("10/100 speed: disabling TSO\n");
+			netdev->features &= ~NETIF_F_TSO;
+			netdev->features &= ~NETIF_F_TSO6;
+			break;
+		case SPEED_1000:
+			netdev->features |= NETIF_F_TSO;
+			netdev->features |= NETIF_F_TSO6;
+			break;
+		default:
+			/* oops */
+			break;
+		}
+		if (hw->mac.type == e1000_pch_spt) {
+			netdev->features &= ~NETIF_F_TSO;
+			netdev->features &= ~NETIF_F_TSO6;
+		}
+	}
+
 	/* Set user-changeable features (subset of all device features) */
 	netdev->hw_features = netdev->features;
 	netdev->hw_features |= NETIF_F_RXFCS;
@@ -7694,7 +7704,7 @@
 
 	dev_pm_set_driver_flags(&pdev->dev, DPM_FLAG_SMART_PREPARE);
 
-	if (pci_dev_run_wake(pdev) && hw->mac.type != e1000_pch_cnp)
+	if (pci_dev_run_wake(pdev))
 		pm_runtime_put_noidle(&pdev->dev);
 
 	return 0;
@@ -7903,22 +7913,22 @@
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V14), board_pch_tgp },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM15), board_pch_tgp },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V15), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM23), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V23), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM16), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V16), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM17), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V17), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM22), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V22), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM18), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V18), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM19), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V19), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM20), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V20), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM21), board_pch_tgp },
-	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V21), board_pch_tgp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM23), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V23), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM16), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V16), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM17), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V17), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM22), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V22), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM18), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V18), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM19), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V19), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM20), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V20), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM21), board_pch_adp },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V21), board_pch_adp },
 
 	{ 0, 0, 0, 0, 0, 0, 0 }	/* terminate list */
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/e1000e/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/e1000e/phy.c
@@ -203,7 +203,7 @@
 	 * Increasing the time out as testing showed failures with
 	 * the lower time out
 	 */
-	for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+	for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 10); i++) {
 		udelay(50);
 		mdic = er32(MDIC);
 		if (mdic & E1000_MDIC_READY)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/fm10k/fm10k_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/fm10k/fm10k_main.c
@@ -32,6 +32,8 @@
  **/
 static int __init fm10k_init_module(void)
 {
+	int ret;
+
 	pr_info("%s\n", fm10k_driver_string);
 	pr_info("%s\n", fm10k_copyright);
 
@@ -43,7 +45,13 @@
 
 	fm10k_dbg_init();
 
-	return fm10k_register_pci_driver();
+	ret = fm10k_register_pci_driver();
+	if (ret) {
+		fm10k_dbg_exit();
+		destroy_workqueue(fm10k_workqueue);
+	}
+
+	return ret;
 }
 module_init(fm10k_init_module);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -990,7 +990,7 @@
 	}
 
 	if (!err) {
-		ether_addr_copy(dev->dev_addr, addr->sa_data);
+		eth_hw_addr_set(dev, addr->sa_data);
 		ether_addr_copy(hw->mac.addr, addr->sa_data);
 		dev->addr_assign_type &= ~NET_ADDR_RANDOM;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/fm10k/fm10k_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/fm10k/fm10k_pci.c
@@ -300,7 +300,7 @@
 		if (is_valid_ether_addr(hw->mac.perm_addr)) {
 			ether_addr_copy(hw->mac.addr, hw->mac.perm_addr);
 			ether_addr_copy(netdev->perm_addr, hw->mac.perm_addr);
-			ether_addr_copy(netdev->dev_addr, hw->mac.perm_addr);
+			eth_hw_addr_set(netdev, hw->mac.perm_addr);
 			netdev->addr_assign_type &= ~NET_ADDR_RANDOM;
 		}
 
@@ -2045,7 +2045,7 @@
 		netdev->addr_assign_type |= NET_ADDR_RANDOM;
 	}
 
-	ether_addr_copy(netdev->dev_addr, hw->mac.addr);
+	eth_hw_addr_set(netdev, hw->mac.addr);
 	ether_addr_copy(netdev->perm_addr, hw->mac.addr);
 
 	if (!is_valid_ether_addr(netdev->perm_addr)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e.h
@@ -37,6 +37,7 @@
 #include <net/tc_act/tc_mirred.h>
 #include <net/udp_tunnel.h>
 #include <net/xdp_sock.h>
+#include <linux/bitfield.h>
 #include "i40e_type.h"
 #include "i40e_prototype.h"
 #include <linux/net/intel/i40e_client.h>
@@ -107,7 +108,7 @@
 #define I40E_MAX_BW_INACTIVE_ACCUM	4 /* accumulate 4 credits max */
 
 /* driver state flags */
-enum i40e_state_t {
+enum i40e_state {
 	__I40E_TESTING,
 	__I40E_CONFIG_BUSY,
 	__I40E_CONFIG_DONE,
@@ -144,6 +145,7 @@
 	__I40E_VIRTCHNL_OP_PENDING,
 	__I40E_RECOVERY_MODE,
 	__I40E_VF_RESETS_DISABLED,	/* disable resets during i40e_remove */
+	__I40E_IN_REMOVE,
 	__I40E_VFS_RELEASING,
 	/* This must be last as it determines the size of the BITMAP */
 	__I40E_STATE_SIZE__,
@@ -154,13 +156,14 @@
 	BIT_ULL(__I40E_PF_RESET_AND_REBUILD_REQUESTED)
 
 /* VSI state flags */
-enum i40e_vsi_state_t {
+enum i40e_vsi_state {
 	__I40E_VSI_DOWN,
 	__I40E_VSI_NEEDS_RESTART,
 	__I40E_VSI_SYNCING_FILTERS,
 	__I40E_VSI_OVERFLOW_PROMISC,
 	__I40E_VSI_REINIT_REQUESTED,
 	__I40E_VSI_DOWN_REQUESTED,
+	__I40E_VSI_RELEASING,
 	/* This must be last as it determines the size of the BITMAP */
 	__I40E_VSI_STATE_SIZE__,
 };
@@ -173,7 +176,6 @@
 
 struct i40e_lump_tracking {
 	u16 num_entries;
-	u16 search_hint;
 	u16 list[0];
 #define I40E_PILE_VALID_BIT  0x8000
 #define I40E_IWARP_IRQ_PILE_ID  (I40E_PILE_VALID_BIT - 2)
@@ -435,7 +437,7 @@
 	return !!ch->fwd;
 }
 
-static inline u8 *i40e_channel_mac(struct i40e_channel *ch)
+static inline const u8 *i40e_channel_mac(struct i40e_channel *ch)
 {
 	if (i40e_is_channel_macvlan(ch))
 		return ch->fwd->netdev->dev_addr;
@@ -586,6 +588,7 @@
  *   in abilities field of i40e_aq_set_phy_config structure
  */
 #define I40E_FLAG_TOTAL_PORT_SHUTDOWN_ENABLED	BIT(27)
+#define I40E_FLAG_VF_VLAN_PRUNING		BIT(28)
 
 	struct i40e_client_instance *cinst;
 	bool stat_offsets_loaded;
@@ -773,6 +776,7 @@
 	I40E_FILTER_ACTIVE,		/* Added to switch by FW */
 	I40E_FILTER_FAILED,		/* Rejected by FW */
 	I40E_FILTER_REMOVE,		/* To be removed */
+	I40E_FILTER_NEW_SYNC,		/* New, not sent yet, is in i40e_sync_vsi_filters() */
 /* There is no 'removed' state; the filter struct is freed */
 };
 struct i40e_mac_filter {
@@ -847,12 +851,12 @@
 	struct rtnl_link_stats64 net_stats_offsets;
 	struct i40e_eth_stats eth_stats;
 	struct i40e_eth_stats eth_stats_offsets;
-	u32 tx_restart;
-	u32 tx_busy;
+	u64 tx_restart;
+	u64 tx_busy;
 	u64 tx_linearize;
 	u64 tx_force_wb;
-	u32 rx_buf_failed;
-	u32 rx_page_failed;
+	u64 rx_buf_failed;
+	u64 rx_page_failed;
 
 	/* These are containers of ring pointers, allocated at run-time */
 	struct i40e_ring **rx_rings;
@@ -970,6 +974,8 @@
 	struct rcu_head rcu;	/* to avoid race with update stats on free */
 	char name[I40E_INT_NAME_STR_LEN];
 	bool arm_wb_state;
+	bool in_busy_poll;
+	int irq_num;		/* IRQ assigned to this q_vector */
 } ____cacheline_internodealigned_in_smp;
 
 /* lan device */
@@ -1086,6 +1092,21 @@
 			  (u32)(val & 0xFFFFFFFFULL));
 }
 
+/**
+ * i40e_get_pf_count - get PCI PF count.
+ * @hw: pointer to a hw.
+ *
+ * Reports the function number of the highest PCI physical
+ * function plus 1 as it is loaded from the NVM.
+ *
+ * Return: PCI PF count.
+ **/
+static inline u32 i40e_get_pf_count(struct i40e_hw *hw)
+{
+	return FIELD_GET(I40E_GLGEN_PCIFCNCNT_PCIPFCNT_MASK,
+			 rd32(hw, I40E_GLGEN_PCIFCNCNT));
+}
+
 /* needed by i40e_ethtool.c */
 int i40e_up(struct i40e_vsi *vsi);
 void i40e_down(struct i40e_vsi *vsi);
@@ -1247,10 +1268,11 @@
 void i40e_ptp_init(struct i40e_pf *pf);
 void i40e_ptp_stop(struct i40e_pf *pf);
 int i40e_ptp_alloc_pins(struct i40e_pf *pf);
+int i40e_update_adq_vsi_queues(struct i40e_vsi *vsi, int vsi_offset);
 int i40e_is_vsi_uplink_mode_veb(struct i40e_vsi *vsi);
-i40e_status i40e_get_partition_bw_setting(struct i40e_pf *pf);
-i40e_status i40e_set_partition_bw_setting(struct i40e_pf *pf);
-i40e_status i40e_commit_partition_bw_setting(struct i40e_pf *pf);
+int i40e_get_partition_bw_setting(struct i40e_pf *pf);
+int i40e_set_partition_bw_setting(struct i40e_pf *pf);
+int i40e_commit_partition_bw_setting(struct i40e_pf *pf);
 void i40e_print_link_message(struct i40e_vsi *vsi, bool isup);
 
 void i40e_set_fec_in_flags(u8 fec_cfg, u32 *flags);
@@ -1268,4 +1290,18 @@
 int i40e_add_del_cloud_filter_big_buf(struct i40e_vsi *vsi,
 				      struct i40e_cloud_filter *filter,
 				      bool add);
+
+/**
+ * i40e_is_tc_mqprio_enabled - check if TC MQPRIO is enabled on PF
+ * @pf: pointer to a pf.
+ *
+ * Check and return value of flag I40E_FLAG_TC_MQPRIO.
+ *
+ * Return: I40E_FLAG_TC_MQPRIO set state.
+ **/
+static inline u32 i40e_is_tc_mqprio_enabled(struct i40e_pf *pf)
+{
+	return pf->flags & I40E_FLAG_TC_MQPRIO;
+}
+
 #endif /* _I40E_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_adminq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_adminq.c
@@ -47,9 +47,9 @@
  *  i40e_alloc_adminq_asq_ring - Allocate Admin Queue send rings
  *  @hw: pointer to the hardware structure
  **/
-static i40e_status i40e_alloc_adminq_asq_ring(struct i40e_hw *hw)
+static int i40e_alloc_adminq_asq_ring(struct i40e_hw *hw)
 {
-	i40e_status ret_code;
+	int ret_code;
 
 	ret_code = i40e_allocate_dma_mem(hw, &hw->aq.asq.desc_buf,
 					 i40e_mem_atq_ring,
@@ -74,9 +74,9 @@
  *  i40e_alloc_adminq_arq_ring - Allocate Admin Queue receive rings
  *  @hw: pointer to the hardware structure
  **/
-static i40e_status i40e_alloc_adminq_arq_ring(struct i40e_hw *hw)
+static int i40e_alloc_adminq_arq_ring(struct i40e_hw *hw)
 {
-	i40e_status ret_code;
+	int ret_code;
 
 	ret_code = i40e_allocate_dma_mem(hw, &hw->aq.arq.desc_buf,
 					 i40e_mem_arq_ring,
@@ -115,11 +115,11 @@
  *  i40e_alloc_arq_bufs - Allocate pre-posted buffers for the receive queue
  *  @hw: pointer to the hardware structure
  **/
-static i40e_status i40e_alloc_arq_bufs(struct i40e_hw *hw)
+static int i40e_alloc_arq_bufs(struct i40e_hw *hw)
 {
-	i40e_status ret_code;
 	struct i40e_aq_desc *desc;
 	struct i40e_dma_mem *bi;
+	int ret_code;
 	int i;
 
 	/* We'll be allocating the buffer info memory first, then we can
@@ -182,10 +182,10 @@
  *  i40e_alloc_asq_bufs - Allocate empty buffer structs for the send queue
  *  @hw: pointer to the hardware structure
  **/
-static i40e_status i40e_alloc_asq_bufs(struct i40e_hw *hw)
+static int i40e_alloc_asq_bufs(struct i40e_hw *hw)
 {
-	i40e_status ret_code;
 	struct i40e_dma_mem *bi;
+	int ret_code;
 	int i;
 
 	/* No mapped memory needed yet, just the buffer info structures */
@@ -266,9 +266,9 @@
  *
  *  Configure base address and length registers for the transmit queue
  **/
-static i40e_status i40e_config_asq_regs(struct i40e_hw *hw)
+static int i40e_config_asq_regs(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 	u32 reg = 0;
 
 	/* Clear Head and Tail */
@@ -295,9 +295,9 @@
  *
  * Configure base address and length registers for the receive (event queue)
  **/
-static i40e_status i40e_config_arq_regs(struct i40e_hw *hw)
+static int i40e_config_arq_regs(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 	u32 reg = 0;
 
 	/* Clear Head and Tail */
@@ -334,9 +334,9 @@
  *  Do *NOT* hold the lock when calling this as the memory allocation routines
  *  called are not going to be atomic context safe
  **/
-static i40e_status i40e_init_asq(struct i40e_hw *hw)
+static int i40e_init_asq(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	if (hw->aq.asq.count > 0) {
 		/* queue already initialized */
@@ -393,9 +393,9 @@
  *  Do *NOT* hold the lock when calling this as the memory allocation routines
  *  called are not going to be atomic context safe
  **/
-static i40e_status i40e_init_arq(struct i40e_hw *hw)
+static int i40e_init_arq(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	if (hw->aq.arq.count > 0) {
 		/* queue already initialized */
@@ -445,9 +445,9 @@
  *
  *  The main shutdown routine for the Admin Send Queue
  **/
-static i40e_status i40e_shutdown_asq(struct i40e_hw *hw)
+static int i40e_shutdown_asq(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	mutex_lock(&hw->aq.asq_mutex);
 
@@ -479,9 +479,9 @@
  *
  *  The main shutdown routine for the Admin Receive Queue
  **/
-static i40e_status i40e_shutdown_arq(struct i40e_hw *hw)
+static int i40e_shutdown_arq(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	mutex_lock(&hw->aq.arq_mutex);
 
@@ -582,12 +582,12 @@
  *     - hw->aq.arq_buf_size
  *     - hw->aq.asq_buf_size
  **/
-i40e_status i40e_init_adminq(struct i40e_hw *hw)
+int i40e_init_adminq(struct i40e_hw *hw)
 {
 	u16 cfg_ptr, oem_hi, oem_lo;
 	u16 eetrack_lo, eetrack_hi;
-	i40e_status ret_code;
 	int retry = 0;
+	int ret_code;
 
 	/* verify input for valid configuration */
 	if ((hw->aq.num_arq_entries == 0) ||
@@ -779,18 +779,18 @@
  *  This is the main send command driver routine for the Admin Queue send
  *  queue.  It runs the queue, cleans the queue, etc
  **/
-i40e_status i40e_asq_send_command(struct i40e_hw *hw,
-				struct i40e_aq_desc *desc,
-				void *buff, /* can be NULL */
-				u16  buff_size,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_asq_send_command(struct i40e_hw *hw,
+			  struct i40e_aq_desc *desc,
+			  void *buff, /* can be NULL */
+			  u16  buff_size,
+			  struct i40e_asq_cmd_details *cmd_details)
 {
-	i40e_status status = 0;
 	struct i40e_dma_mem *dma_buff = NULL;
 	struct i40e_asq_cmd_details *details;
 	struct i40e_aq_desc *desc_on_ring;
 	bool cmd_completed = false;
 	u16  retval = 0;
+	int status = 0;
 	u32  val = 0;
 
 	mutex_lock(&hw->aq.asq_mutex);
@@ -993,14 +993,14 @@
  *  the contents through e.  It can also return how many events are
  *  left to process through 'pending'
  **/
-i40e_status i40e_clean_arq_element(struct i40e_hw *hw,
-					     struct i40e_arq_event_info *e,
-					     u16 *pending)
+int i40e_clean_arq_element(struct i40e_hw *hw,
+			   struct i40e_arq_event_info *e,
+			   u16 *pending)
 {
-	i40e_status ret_code = 0;
 	u16 ntc = hw->aq.arq.next_to_clean;
 	struct i40e_aq_desc *desc;
 	struct i40e_dma_mem *bi;
+	int ret_code = 0;
 	u16 desc_idx;
 	u16 datalen;
 	u16 flags;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_alloc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_alloc.h
@@ -20,16 +20,16 @@
 };
 
 /* prototype for functions used for dynamic memory allocation */
-i40e_status i40e_allocate_dma_mem(struct i40e_hw *hw,
-					    struct i40e_dma_mem *mem,
-					    enum i40e_memory_type type,
-					    u64 size, u32 alignment);
-i40e_status i40e_free_dma_mem(struct i40e_hw *hw,
-					struct i40e_dma_mem *mem);
-i40e_status i40e_allocate_virt_mem(struct i40e_hw *hw,
-					     struct i40e_virt_mem *mem,
-					     u32 size);
-i40e_status i40e_free_virt_mem(struct i40e_hw *hw,
-					 struct i40e_virt_mem *mem);
+int i40e_allocate_dma_mem(struct i40e_hw *hw,
+			  struct i40e_dma_mem *mem,
+			  enum i40e_memory_type type,
+			  u64 size, u32 alignment);
+int i40e_free_dma_mem(struct i40e_hw *hw,
+		      struct i40e_dma_mem *mem);
+int i40e_allocate_virt_mem(struct i40e_hw *hw,
+			   struct i40e_virt_mem *mem,
+			   u32 size);
+int i40e_free_virt_mem(struct i40e_hw *hw,
+		       struct i40e_virt_mem *mem);
 
 #endif /* _I40E_ALLOC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_client.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_client.c
@@ -177,6 +177,10 @@
 			"Cannot locate client instance close routine\n");
 		return;
 	}
+	if (!test_bit(__I40E_CLIENT_INSTANCE_OPENED, &cdev->state)) {
+		dev_dbg(&pf->pdev->dev, "Client is not open, abort close\n");
+		return;
+	}
 	cdev->client->ops->close(&cdev->lan_info, cdev->client, reset);
 	clear_bit(__I40E_CLIENT_INSTANCE_OPENED, &cdev->state);
 	i40e_client_release_qvlist(&cdev->lan_info);
@@ -429,7 +433,6 @@
 				/* Remove failed client instance */
 				clear_bit(__I40E_CLIENT_INSTANCE_OPENED,
 					  &cdev->state);
-				i40e_client_del_instance(pf);
 				return;
 			}
 		}
@@ -538,7 +541,7 @@
 {
 	struct i40e_pf *pf = ldev->pf;
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status err;
+	int err;
 
 	err = i40e_aq_send_msg_to_vf(hw, vf_id, VIRTCHNL_OP_IWARP,
 				     0, msg, len, NULL);
@@ -671,7 +674,7 @@
 	struct i40e_vsi *vsi = pf->vsi[pf->lan_vsi];
 	struct i40e_vsi_context ctxt;
 	bool update = true;
-	i40e_status err;
+	int err;
 
 	/* TODO: for now do not allow setting VF's VSI setting */
 	if (is_vf)
@@ -683,8 +686,8 @@
 	ctxt.flags = I40E_AQ_VSI_TYPE_PF;
 	if (err) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get PF vsi config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, err),
+			 "couldn't get PF vsi config, err %d aq_err %s\n",
+			 err,
 			 i40e_aq_str(&pf->hw,
 				     pf->hw.aq.asq_last_status));
 		return -ENOENT;
@@ -711,8 +714,8 @@
 		err = i40e_aq_update_vsi_params(&vsi->back->hw, &ctxt, NULL);
 		if (err) {
 			dev_info(&pf->pdev->dev,
-				 "update VSI ctxt for PE failed, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, err),
+				 "update VSI ctxt for PE failed, err %d aq_err %s\n",
+				 err,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_common.c
@@ -14,9 +14,9 @@
  * This function sets the mac type of the adapter based on the
  * vendor ID and device ID stored in the hw structure.
  **/
-i40e_status i40e_set_mac_type(struct i40e_hw *hw)
+int i40e_set_mac_type(struct i40e_hw *hw)
 {
-	i40e_status status = 0;
+	int status = 0;
 
 	if (hw->vendor_id == PCI_VENDOR_ID_INTEL) {
 		switch (hw->device_id) {
@@ -123,154 +123,6 @@
 }
 
 /**
- * i40e_stat_str - convert status err code to a string
- * @hw: pointer to the HW structure
- * @stat_err: the status error code to convert
- **/
-const char *i40e_stat_str(struct i40e_hw *hw, i40e_status stat_err)
-{
-	switch (stat_err) {
-	case 0:
-		return "OK";
-	case I40E_ERR_NVM:
-		return "I40E_ERR_NVM";
-	case I40E_ERR_NVM_CHECKSUM:
-		return "I40E_ERR_NVM_CHECKSUM";
-	case I40E_ERR_PHY:
-		return "I40E_ERR_PHY";
-	case I40E_ERR_CONFIG:
-		return "I40E_ERR_CONFIG";
-	case I40E_ERR_PARAM:
-		return "I40E_ERR_PARAM";
-	case I40E_ERR_MAC_TYPE:
-		return "I40E_ERR_MAC_TYPE";
-	case I40E_ERR_UNKNOWN_PHY:
-		return "I40E_ERR_UNKNOWN_PHY";
-	case I40E_ERR_LINK_SETUP:
-		return "I40E_ERR_LINK_SETUP";
-	case I40E_ERR_ADAPTER_STOPPED:
-		return "I40E_ERR_ADAPTER_STOPPED";
-	case I40E_ERR_INVALID_MAC_ADDR:
-		return "I40E_ERR_INVALID_MAC_ADDR";
-	case I40E_ERR_DEVICE_NOT_SUPPORTED:
-		return "I40E_ERR_DEVICE_NOT_SUPPORTED";
-	case I40E_ERR_MASTER_REQUESTS_PENDING:
-		return "I40E_ERR_MASTER_REQUESTS_PENDING";
-	case I40E_ERR_INVALID_LINK_SETTINGS:
-		return "I40E_ERR_INVALID_LINK_SETTINGS";
-	case I40E_ERR_AUTONEG_NOT_COMPLETE:
-		return "I40E_ERR_AUTONEG_NOT_COMPLETE";
-	case I40E_ERR_RESET_FAILED:
-		return "I40E_ERR_RESET_FAILED";
-	case I40E_ERR_SWFW_SYNC:
-		return "I40E_ERR_SWFW_SYNC";
-	case I40E_ERR_NO_AVAILABLE_VSI:
-		return "I40E_ERR_NO_AVAILABLE_VSI";
-	case I40E_ERR_NO_MEMORY:
-		return "I40E_ERR_NO_MEMORY";
-	case I40E_ERR_BAD_PTR:
-		return "I40E_ERR_BAD_PTR";
-	case I40E_ERR_RING_FULL:
-		return "I40E_ERR_RING_FULL";
-	case I40E_ERR_INVALID_PD_ID:
-		return "I40E_ERR_INVALID_PD_ID";
-	case I40E_ERR_INVALID_QP_ID:
-		return "I40E_ERR_INVALID_QP_ID";
-	case I40E_ERR_INVALID_CQ_ID:
-		return "I40E_ERR_INVALID_CQ_ID";
-	case I40E_ERR_INVALID_CEQ_ID:
-		return "I40E_ERR_INVALID_CEQ_ID";
-	case I40E_ERR_INVALID_AEQ_ID:
-		return "I40E_ERR_INVALID_AEQ_ID";
-	case I40E_ERR_INVALID_SIZE:
-		return "I40E_ERR_INVALID_SIZE";
-	case I40E_ERR_INVALID_ARP_INDEX:
-		return "I40E_ERR_INVALID_ARP_INDEX";
-	case I40E_ERR_INVALID_FPM_FUNC_ID:
-		return "I40E_ERR_INVALID_FPM_FUNC_ID";
-	case I40E_ERR_QP_INVALID_MSG_SIZE:
-		return "I40E_ERR_QP_INVALID_MSG_SIZE";
-	case I40E_ERR_QP_TOOMANY_WRS_POSTED:
-		return "I40E_ERR_QP_TOOMANY_WRS_POSTED";
-	case I40E_ERR_INVALID_FRAG_COUNT:
-		return "I40E_ERR_INVALID_FRAG_COUNT";
-	case I40E_ERR_QUEUE_EMPTY:
-		return "I40E_ERR_QUEUE_EMPTY";
-	case I40E_ERR_INVALID_ALIGNMENT:
-		return "I40E_ERR_INVALID_ALIGNMENT";
-	case I40E_ERR_FLUSHED_QUEUE:
-		return "I40E_ERR_FLUSHED_QUEUE";
-	case I40E_ERR_INVALID_PUSH_PAGE_INDEX:
-		return "I40E_ERR_INVALID_PUSH_PAGE_INDEX";
-	case I40E_ERR_INVALID_IMM_DATA_SIZE:
-		return "I40E_ERR_INVALID_IMM_DATA_SIZE";
-	case I40E_ERR_TIMEOUT:
-		return "I40E_ERR_TIMEOUT";
-	case I40E_ERR_OPCODE_MISMATCH:
-		return "I40E_ERR_OPCODE_MISMATCH";
-	case I40E_ERR_CQP_COMPL_ERROR:
-		return "I40E_ERR_CQP_COMPL_ERROR";
-	case I40E_ERR_INVALID_VF_ID:
-		return "I40E_ERR_INVALID_VF_ID";
-	case I40E_ERR_INVALID_HMCFN_ID:
-		return "I40E_ERR_INVALID_HMCFN_ID";
-	case I40E_ERR_BACKING_PAGE_ERROR:
-		return "I40E_ERR_BACKING_PAGE_ERROR";
-	case I40E_ERR_NO_PBLCHUNKS_AVAILABLE:
-		return "I40E_ERR_NO_PBLCHUNKS_AVAILABLE";
-	case I40E_ERR_INVALID_PBLE_INDEX:
-		return "I40E_ERR_INVALID_PBLE_INDEX";
-	case I40E_ERR_INVALID_SD_INDEX:
-		return "I40E_ERR_INVALID_SD_INDEX";
-	case I40E_ERR_INVALID_PAGE_DESC_INDEX:
-		return "I40E_ERR_INVALID_PAGE_DESC_INDEX";
-	case I40E_ERR_INVALID_SD_TYPE:
-		return "I40E_ERR_INVALID_SD_TYPE";
-	case I40E_ERR_MEMCPY_FAILED:
-		return "I40E_ERR_MEMCPY_FAILED";
-	case I40E_ERR_INVALID_HMC_OBJ_INDEX:
-		return "I40E_ERR_INVALID_HMC_OBJ_INDEX";
-	case I40E_ERR_INVALID_HMC_OBJ_COUNT:
-		return "I40E_ERR_INVALID_HMC_OBJ_COUNT";
-	case I40E_ERR_INVALID_SRQ_ARM_LIMIT:
-		return "I40E_ERR_INVALID_SRQ_ARM_LIMIT";
-	case I40E_ERR_SRQ_ENABLED:
-		return "I40E_ERR_SRQ_ENABLED";
-	case I40E_ERR_ADMIN_QUEUE_ERROR:
-		return "I40E_ERR_ADMIN_QUEUE_ERROR";
-	case I40E_ERR_ADMIN_QUEUE_TIMEOUT:
-		return "I40E_ERR_ADMIN_QUEUE_TIMEOUT";
-	case I40E_ERR_BUF_TOO_SHORT:
-		return "I40E_ERR_BUF_TOO_SHORT";
-	case I40E_ERR_ADMIN_QUEUE_FULL:
-		return "I40E_ERR_ADMIN_QUEUE_FULL";
-	case I40E_ERR_ADMIN_QUEUE_NO_WORK:
-		return "I40E_ERR_ADMIN_QUEUE_NO_WORK";
-	case I40E_ERR_BAD_IWARP_CQE:
-		return "I40E_ERR_BAD_IWARP_CQE";
-	case I40E_ERR_NVM_BLANK_MODE:
-		return "I40E_ERR_NVM_BLANK_MODE";
-	case I40E_ERR_NOT_IMPLEMENTED:
-		return "I40E_ERR_NOT_IMPLEMENTED";
-	case I40E_ERR_PE_DOORBELL_NOT_ENABLED:
-		return "I40E_ERR_PE_DOORBELL_NOT_ENABLED";
-	case I40E_ERR_DIAG_TEST_FAILED:
-		return "I40E_ERR_DIAG_TEST_FAILED";
-	case I40E_ERR_NOT_READY:
-		return "I40E_ERR_NOT_READY";
-	case I40E_NOT_SUPPORTED:
-		return "I40E_NOT_SUPPORTED";
-	case I40E_ERR_FIRMWARE_API_VERSION:
-		return "I40E_ERR_FIRMWARE_API_VERSION";
-	case I40E_ERR_ADMIN_QUEUE_CRITICAL_ERROR:
-		return "I40E_ERR_ADMIN_QUEUE_CRITICAL_ERROR";
-	}
-
-	snprintf(hw->err_str, sizeof(hw->err_str), "%d", stat_err);
-	return hw->err_str;
-}
-
-/**
  * i40e_debug_aq
  * @hw: debug mask related to admin queue
  * @mask: debug mask
@@ -353,13 +205,13 @@
  * Tell the Firmware that we're shutting down the AdminQ and whether
  * or not the driver is unloading as well.
  **/
-i40e_status i40e_aq_queue_shutdown(struct i40e_hw *hw,
-					     bool unloading)
+int i40e_aq_queue_shutdown(struct i40e_hw *hw,
+			   bool unloading)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_queue_shutdown *cmd =
 		(struct i40e_aqc_queue_shutdown *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_queue_shutdown);
@@ -382,15 +234,15 @@
  *
  * Internal function to get or set RSS look up table
  **/
-static i40e_status i40e_aq_get_set_rss_lut(struct i40e_hw *hw,
-					   u16 vsi_id, bool pf_lut,
-					   u8 *lut, u16 lut_size,
-					   bool set)
+static int i40e_aq_get_set_rss_lut(struct i40e_hw *hw,
+				   u16 vsi_id, bool pf_lut,
+				   u8 *lut, u16 lut_size,
+				   bool set)
 {
-	i40e_status status;
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_get_set_rss_lut *cmd_resp =
 		   (struct i40e_aqc_get_set_rss_lut *)&desc.params.raw;
+	int status;
 
 	if (set)
 		i40e_fill_default_direct_cmd_desc(&desc,
@@ -435,8 +287,8 @@
  *
  * get the RSS lookup table, PF or VSI type
  **/
-i40e_status i40e_aq_get_rss_lut(struct i40e_hw *hw, u16 vsi_id,
-				bool pf_lut, u8 *lut, u16 lut_size)
+int i40e_aq_get_rss_lut(struct i40e_hw *hw, u16 vsi_id,
+			bool pf_lut, u8 *lut, u16 lut_size)
 {
 	return i40e_aq_get_set_rss_lut(hw, vsi_id, pf_lut, lut, lut_size,
 				       false);
@@ -452,8 +304,8 @@
  *
  * set the RSS lookup table, PF or VSI type
  **/
-i40e_status i40e_aq_set_rss_lut(struct i40e_hw *hw, u16 vsi_id,
-				bool pf_lut, u8 *lut, u16 lut_size)
+int i40e_aq_set_rss_lut(struct i40e_hw *hw, u16 vsi_id,
+			bool pf_lut, u8 *lut, u16 lut_size)
 {
 	return i40e_aq_get_set_rss_lut(hw, vsi_id, pf_lut, lut, lut_size, true);
 }
@@ -467,16 +319,16 @@
  *
  * get the RSS key per VSI
  **/
-static i40e_status i40e_aq_get_set_rss_key(struct i40e_hw *hw,
-				      u16 vsi_id,
-				      struct i40e_aqc_get_set_rss_key_data *key,
-				      bool set)
+static int i40e_aq_get_set_rss_key(struct i40e_hw *hw,
+				   u16 vsi_id,
+				   struct i40e_aqc_get_set_rss_key_data *key,
+				   bool set)
 {
-	i40e_status status;
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_get_set_rss_key *cmd_resp =
 			(struct i40e_aqc_get_set_rss_key *)&desc.params.raw;
 	u16 key_size = sizeof(struct i40e_aqc_get_set_rss_key_data);
+	int status;
 
 	if (set)
 		i40e_fill_default_direct_cmd_desc(&desc,
@@ -507,9 +359,9 @@
  * @key: pointer to key info struct
  *
  **/
-i40e_status i40e_aq_get_rss_key(struct i40e_hw *hw,
-				u16 vsi_id,
-				struct i40e_aqc_get_set_rss_key_data *key)
+int i40e_aq_get_rss_key(struct i40e_hw *hw,
+			u16 vsi_id,
+			struct i40e_aqc_get_set_rss_key_data *key)
 {
 	return i40e_aq_get_set_rss_key(hw, vsi_id, key, false);
 }
@@ -522,9 +374,9 @@
  *
  * set the RSS key per VSI
  **/
-i40e_status i40e_aq_set_rss_key(struct i40e_hw *hw,
-				u16 vsi_id,
-				struct i40e_aqc_get_set_rss_key_data *key)
+int i40e_aq_set_rss_key(struct i40e_hw *hw,
+			u16 vsi_id,
+			struct i40e_aqc_get_set_rss_key_data *key)
 {
 	return i40e_aq_get_set_rss_key(hw, vsi_id, key, true);
 }
@@ -794,10 +646,10 @@
  * hw_addr, back, device_id, vendor_id, subsystem_device_id,
  * subsystem_vendor_id, and revision_id
  **/
-i40e_status i40e_init_shared_code(struct i40e_hw *hw)
+int i40e_init_shared_code(struct i40e_hw *hw)
 {
-	i40e_status status = 0;
 	u32 port, ari, func_rid;
+	int status = 0;
 
 	i40e_set_mac_type(hw);
 
@@ -834,15 +686,16 @@
  * @addrs: the requestor's mac addr store
  * @cmd_details: pointer to command details structure or NULL
  **/
-static i40e_status i40e_aq_mac_address_read(struct i40e_hw *hw,
-				   u16 *flags,
-				   struct i40e_aqc_mac_address_read_data *addrs,
-				   struct i40e_asq_cmd_details *cmd_details)
+static int
+i40e_aq_mac_address_read(struct i40e_hw *hw,
+			 u16 *flags,
+			 struct i40e_aqc_mac_address_read_data *addrs,
+			 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_mac_address_read *cmd_data =
 		(struct i40e_aqc_mac_address_read *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_mac_address_read);
 	desc.flags |= cpu_to_le16(I40E_AQ_FLAG_BUF);
@@ -861,14 +714,14 @@
  * @mac_addr: address to write
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_mac_address_write(struct i40e_hw *hw,
-				    u16 flags, u8 *mac_addr,
-				    struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_mac_address_write(struct i40e_hw *hw,
+			      u16 flags, u8 *mac_addr,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_mac_address_write *cmd_data =
 		(struct i40e_aqc_mac_address_write *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_mac_address_write);
@@ -891,11 +744,11 @@
  *
  * Reads the adapter's MAC address from register
  **/
-i40e_status i40e_get_mac_addr(struct i40e_hw *hw, u8 *mac_addr)
+int i40e_get_mac_addr(struct i40e_hw *hw, u8 *mac_addr)
 {
 	struct i40e_aqc_mac_address_read_data addrs;
-	i40e_status status;
 	u16 flags = 0;
+	int status;
 
 	status = i40e_aq_mac_address_read(hw, &flags, &addrs, NULL);
 
@@ -912,11 +765,11 @@
  *
  * Reads the adapter's Port MAC address
  **/
-i40e_status i40e_get_port_mac_addr(struct i40e_hw *hw, u8 *mac_addr)
+int i40e_get_port_mac_addr(struct i40e_hw *hw, u8 *mac_addr)
 {
 	struct i40e_aqc_mac_address_read_data addrs;
-	i40e_status status;
 	u16 flags = 0;
+	int status;
 
 	status = i40e_aq_mac_address_read(hw, &flags, &addrs, NULL);
 	if (status)
@@ -970,13 +823,13 @@
  *
  *  Reads the part number string from the EEPROM.
  **/
-i40e_status i40e_read_pba_string(struct i40e_hw *hw, u8 *pba_num,
-				 u32 pba_num_size)
+int i40e_read_pba_string(struct i40e_hw *hw, u8 *pba_num,
+			 u32 pba_num_size)
 {
-	i40e_status status = 0;
 	u16 pba_word = 0;
 	u16 pba_size = 0;
 	u16 pba_ptr = 0;
+	int status = 0;
 	u16 i = 0;
 
 	status = i40e_read_nvm_word(hw, I40E_SR_PBA_FLAGS, &pba_word);
@@ -1085,8 +938,8 @@
  * @hw: pointer to the hardware structure
  * @retry_limit: how many times to retry before failure
  **/
-static i40e_status i40e_poll_globr(struct i40e_hw *hw,
-				   u32 retry_limit)
+static int i40e_poll_globr(struct i40e_hw *hw,
+			   u32 retry_limit)
 {
 	u32 cnt, reg = 0;
 
@@ -1112,7 +965,7 @@
  * Assuming someone else has triggered a global reset,
  * assure the global reset is complete and then reset the PF
  **/
-i40e_status i40e_pf_reset(struct i40e_hw *hw)
+int i40e_pf_reset(struct i40e_hw *hw)
 {
 	u32 cnt = 0;
 	u32 cnt1 = 0;
@@ -1227,7 +1080,7 @@
 		     I40E_PFLAN_QALLOC_FIRSTQ_SHIFT;
 	j = (val & I40E_PFLAN_QALLOC_LASTQ_MASK) >>
 	    I40E_PFLAN_QALLOC_LASTQ_SHIFT;
-	if (val & I40E_PFLAN_QALLOC_VALID_MASK)
+	if (val & I40E_PFLAN_QALLOC_VALID_MASK && j >= base_queue)
 		num_queues = (j - base_queue) + 1;
 	else
 		num_queues = 0;
@@ -1237,7 +1090,7 @@
 	    I40E_PF_VT_PFALLOC_FIRSTVF_SHIFT;
 	j = (val & I40E_PF_VT_PFALLOC_LASTVF_MASK) >>
 	    I40E_PF_VT_PFALLOC_LASTVF_SHIFT;
-	if (val & I40E_PF_VT_PFALLOC_VALID_MASK)
+	if (val & I40E_PF_VT_PFALLOC_VALID_MASK && j >= i)
 		num_vfs = (j - i) + 1;
 	else
 		num_vfs = 0;
@@ -1451,15 +1304,16 @@
  *
  * Returns the various PHY abilities supported on the Port.
  **/
-i40e_status i40e_aq_get_phy_capabilities(struct i40e_hw *hw,
-			bool qualified_modules, bool report_init,
-			struct i40e_aq_get_phy_abilities_resp *abilities,
-			struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_get_phy_capabilities(struct i40e_hw *hw,
+			     bool qualified_modules, bool report_init,
+			     struct i40e_aq_get_phy_abilities_resp *abilities,
+			     struct i40e_asq_cmd_details *cmd_details)
 {
-	struct i40e_aq_desc desc;
-	i40e_status status;
 	u16 abilities_size = sizeof(struct i40e_aq_get_phy_abilities_resp);
 	u16 max_delay = I40E_MAX_PHY_TIMEOUT, total_delay = 0;
+	struct i40e_aq_desc desc;
+	int status;
 
 	if (!abilities)
 		return I40E_ERR_PARAM;
@@ -1530,14 +1384,14 @@
  * of the PHY Config parameters. This status will be indicated by the
  * command response.
  **/
-enum i40e_status_code i40e_aq_set_phy_config(struct i40e_hw *hw,
-				struct i40e_aq_set_phy_config *config,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_phy_config(struct i40e_hw *hw,
+			   struct i40e_aq_set_phy_config *config,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aq_set_phy_config *cmd =
 			(struct i40e_aq_set_phy_config *)&desc.params.raw;
-	enum i40e_status_code status;
+	int status;
 
 	if (!config)
 		return I40E_ERR_PARAM;
@@ -1552,7 +1406,7 @@
 	return status;
 }
 
-static noinline_for_stack enum i40e_status_code
+static noinline_for_stack int
 i40e_set_fc_status(struct i40e_hw *hw,
 		   struct i40e_aq_get_phy_abilities_resp *abilities,
 		   bool atomic_restart)
@@ -1610,11 +1464,11 @@
  *
  * Set the requested flow control mode using set_phy_config.
  **/
-enum i40e_status_code i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
-				  bool atomic_restart)
+int i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
+		bool atomic_restart)
 {
 	struct i40e_aq_get_phy_abilities_resp abilities;
-	enum i40e_status_code status;
+	int status;
 
 	*aq_failures = 0x0;
 
@@ -1653,13 +1507,13 @@
  *
  * Tell the firmware that the driver is taking over from PXE
  **/
-i40e_status i40e_aq_clear_pxe_mode(struct i40e_hw *hw,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_clear_pxe_mode(struct i40e_hw *hw,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
-	i40e_status status;
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_clear_pxe *cmd =
 		(struct i40e_aqc_clear_pxe *)&desc.params.raw;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_clear_pxe_mode);
@@ -1681,14 +1535,14 @@
  *
  * Sets up the link and restarts the Auto-Negotiation over the link.
  **/
-i40e_status i40e_aq_set_link_restart_an(struct i40e_hw *hw,
-					bool enable_link,
-					struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_link_restart_an(struct i40e_hw *hw,
+				bool enable_link,
+				struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_link_restart_an *cmd =
 		(struct i40e_aqc_set_link_restart_an *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_link_restart_an);
@@ -1713,17 +1567,17 @@
  *
  * Returns the link status of the adapter.
  **/
-i40e_status i40e_aq_get_link_info(struct i40e_hw *hw,
-				bool enable_lse, struct i40e_link_status *link,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_link_info(struct i40e_hw *hw,
+			  bool enable_lse, struct i40e_link_status *link,
+			  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_get_link_status *resp =
 		(struct i40e_aqc_get_link_status *)&desc.params.raw;
 	struct i40e_link_status *hw_link_info = &hw->phy.link_info;
-	i40e_status status;
 	bool tx_pause, rx_pause;
 	u16 command_flags;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_get_link_status);
 
@@ -1809,14 +1663,14 @@
  *
  * Set link interrupt mask.
  **/
-i40e_status i40e_aq_set_phy_int_mask(struct i40e_hw *hw,
-				     u16 mask,
-				     struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_phy_int_mask(struct i40e_hw *hw,
+			     u16 mask,
+			     struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_phy_int_mask *cmd =
 		(struct i40e_aqc_set_phy_int_mask *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_phy_int_mask);
@@ -1836,13 +1690,13 @@
  *
  * Reset the external PHY.
  **/
-i40e_status i40e_aq_set_phy_debug(struct i40e_hw *hw, u8 cmd_flags,
-				  struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_phy_debug(struct i40e_hw *hw, u8 cmd_flags,
+			  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_phy_debug *cmd =
 		(struct i40e_aqc_set_phy_debug *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_phy_debug);
@@ -1877,9 +1731,9 @@
  *
  * Add a VSI context to the hardware.
 **/
-i40e_status i40e_aq_add_vsi(struct i40e_hw *hw,
-				struct i40e_vsi_context *vsi_ctx,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_add_vsi(struct i40e_hw *hw,
+		    struct i40e_vsi_context *vsi_ctx,
+		    struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_get_update_vsi *cmd =
@@ -1887,7 +1741,7 @@
 	struct i40e_aqc_add_get_update_vsi_completion *resp =
 		(struct i40e_aqc_add_get_update_vsi_completion *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_add_vsi);
@@ -1920,15 +1774,15 @@
  * @seid: vsi number
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_set_default_vsi(struct i40e_hw *hw,
-				    u16 seid,
-				    struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_default_vsi(struct i40e_hw *hw,
+			    u16 seid,
+			    struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -1948,15 +1802,15 @@
  * @seid: vsi number
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_clear_default_vsi(struct i40e_hw *hw,
-				      u16 seid,
-				      struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_clear_default_vsi(struct i40e_hw *hw,
+			      u16 seid,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -1978,16 +1832,16 @@
  * @cmd_details: pointer to command details structure or NULL
  * @rx_only_promisc: flag to decide if egress traffic gets mirrored in promisc
  **/
-i40e_status i40e_aq_set_vsi_unicast_promiscuous(struct i40e_hw *hw,
-				u16 seid, bool set,
-				struct i40e_asq_cmd_details *cmd_details,
-				bool rx_only_promisc)
+int i40e_aq_set_vsi_unicast_promiscuous(struct i40e_hw *hw,
+					u16 seid, bool set,
+					struct i40e_asq_cmd_details *cmd_details,
+					bool rx_only_promisc)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	i40e_status status;
 	u16 flags = 0;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2018,14 +1872,15 @@
  * @set: set multicast promiscuous enable/disable
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_set_vsi_multicast_promiscuous(struct i40e_hw *hw,
-				u16 seid, bool set, struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_vsi_multicast_promiscuous(struct i40e_hw *hw,
+					  u16 seid, bool set,
+					  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	i40e_status status;
 	u16 flags = 0;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2051,16 +1906,16 @@
  * @vid: The VLAN tag filter - capture any multicast packet with this VLAN tag
  * @cmd_details: pointer to command details structure or NULL
  **/
-enum i40e_status_code i40e_aq_set_vsi_mc_promisc_on_vlan(struct i40e_hw *hw,
-							 u16 seid, bool enable,
-							 u16 vid,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_vsi_mc_promisc_on_vlan(struct i40e_hw *hw,
+				       u16 seid, bool enable,
+				       u16 vid,
+				       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	enum i40e_status_code status;
 	u16 flags = 0;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2086,16 +1941,16 @@
  * @vid: The VLAN tag filter - capture any unicast packet with this VLAN tag
  * @cmd_details: pointer to command details structure or NULL
  **/
-enum i40e_status_code i40e_aq_set_vsi_uc_promisc_on_vlan(struct i40e_hw *hw,
-							 u16 seid, bool enable,
-							 u16 vid,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_vsi_uc_promisc_on_vlan(struct i40e_hw *hw,
+				       u16 seid, bool enable,
+				       u16 vid,
+				       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	enum i40e_status_code status;
 	u16 flags = 0;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2127,15 +1982,15 @@
  * @vid: The VLAN tag filter - capture any broadcast packet with this VLAN tag
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_set_vsi_bc_promisc_on_vlan(struct i40e_hw *hw,
-				u16 seid, bool enable, u16 vid,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_vsi_bc_promisc_on_vlan(struct i40e_hw *hw,
+				       u16 seid, bool enable, u16 vid,
+				       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	i40e_status status;
 	u16 flags = 0;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2162,14 +2017,14 @@
  *
  * Set or clear the broadcast promiscuous flag (filter) for a given VSI.
  **/
-i40e_status i40e_aq_set_vsi_broadcast(struct i40e_hw *hw,
-				u16 seid, bool set_filter,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_vsi_broadcast(struct i40e_hw *hw,
+			      u16 seid, bool set_filter,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2195,15 +2050,15 @@
  * @enable: set MAC L2 layer unicast promiscuous enable/disable for a given VLAN
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_set_vsi_vlan_promisc(struct i40e_hw *hw,
-				       u16 seid, bool enable,
-				       struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_vsi_vlan_promisc(struct i40e_hw *hw,
+				 u16 seid, bool enable,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_vsi_promiscuous_modes *cmd =
 		(struct i40e_aqc_set_vsi_promiscuous_modes *)&desc.params.raw;
-	i40e_status status;
 	u16 flags = 0;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					i40e_aqc_opc_set_vsi_promiscuous_modes);
@@ -2225,9 +2080,9 @@
  * @vsi_ctx: pointer to a vsi context struct
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_get_vsi_params(struct i40e_hw *hw,
-				struct i40e_vsi_context *vsi_ctx,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_vsi_params(struct i40e_hw *hw,
+			   struct i40e_vsi_context *vsi_ctx,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_get_update_vsi *cmd =
@@ -2235,7 +2090,7 @@
 	struct i40e_aqc_add_get_update_vsi_completion *resp =
 		(struct i40e_aqc_add_get_update_vsi_completion *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_get_vsi_parameters);
@@ -2267,9 +2122,9 @@
  *
  * Update a VSI context.
  **/
-i40e_status i40e_aq_update_vsi_params(struct i40e_hw *hw,
-				struct i40e_vsi_context *vsi_ctx,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_update_vsi_params(struct i40e_hw *hw,
+			      struct i40e_vsi_context *vsi_ctx,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_get_update_vsi *cmd =
@@ -2277,7 +2132,7 @@
 	struct i40e_aqc_add_get_update_vsi_completion *resp =
 		(struct i40e_aqc_add_get_update_vsi_completion *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_update_vsi_parameters);
@@ -2304,15 +2159,15 @@
  *
  * Fill the buf with switch configuration returned from AdminQ command
  **/
-i40e_status i40e_aq_get_switch_config(struct i40e_hw *hw,
-				struct i40e_aqc_get_switch_config_resp *buf,
-				u16 buf_size, u16 *start_seid,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_switch_config(struct i40e_hw *hw,
+			      struct i40e_aqc_get_switch_config_resp *buf,
+			      u16 buf_size, u16 *start_seid,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_switch_seid *scfg =
 		(struct i40e_aqc_switch_seid *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_get_switch_config);
@@ -2338,15 +2193,15 @@
  *
  * Set switch configuration bits
  **/
-enum i40e_status_code i40e_aq_set_switch_config(struct i40e_hw *hw,
-						u16 flags,
-						u16 valid_flags, u8 mode,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_switch_config(struct i40e_hw *hw,
+			      u16 flags,
+			      u16 valid_flags, u8 mode,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_switch_config *scfg =
 		(struct i40e_aqc_set_switch_config *)&desc.params.raw;
-	enum i40e_status_code status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_switch_config);
@@ -2375,16 +2230,16 @@
  *
  * Get the firmware version from the admin queue commands
  **/
-i40e_status i40e_aq_get_firmware_version(struct i40e_hw *hw,
-				u16 *fw_major_version, u16 *fw_minor_version,
-				u32 *fw_build,
-				u16 *api_major_version, u16 *api_minor_version,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_firmware_version(struct i40e_hw *hw,
+				 u16 *fw_major_version, u16 *fw_minor_version,
+				 u32 *fw_build,
+				 u16 *api_major_version, u16 *api_minor_version,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_get_version *resp =
 		(struct i40e_aqc_get_version *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_get_version);
 
@@ -2414,14 +2269,14 @@
  *
  * Send the driver version to the firmware
  **/
-i40e_status i40e_aq_send_driver_version(struct i40e_hw *hw,
+int i40e_aq_send_driver_version(struct i40e_hw *hw,
 				struct i40e_driver_version *dv,
 				struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_driver_version *cmd =
 		(struct i40e_aqc_driver_version *)&desc.params.raw;
-	i40e_status status;
+	int status;
 	u16 len;
 
 	if (dv == NULL)
@@ -2456,9 +2311,9 @@
  *
  * Side effect: LinkStatusEvent reporting becomes enabled
  **/
-i40e_status i40e_get_link_status(struct i40e_hw *hw, bool *link_up)
+int i40e_get_link_status(struct i40e_hw *hw, bool *link_up)
 {
-	i40e_status status = 0;
+	int status = 0;
 
 	if (hw->phy.get_link_info) {
 		status = i40e_update_link_info(hw);
@@ -2477,10 +2332,10 @@
  * i40e_update_link_info - update status of the HW network link
  * @hw: pointer to the hw struct
  **/
-noinline_for_stack i40e_status i40e_update_link_info(struct i40e_hw *hw)
+noinline_for_stack int i40e_update_link_info(struct i40e_hw *hw)
 {
 	struct i40e_aq_get_phy_abilities_resp abilities;
-	i40e_status status = 0;
+	int status = 0;
 
 	status = i40e_aq_get_link_info(hw, true, NULL, NULL);
 	if (status)
@@ -2527,19 +2382,19 @@
  * This asks the FW to add a VEB between the uplink and downlink
  * elements.  If the uplink SEID is 0, this will be a floating VEB.
  **/
-i40e_status i40e_aq_add_veb(struct i40e_hw *hw, u16 uplink_seid,
-				u16 downlink_seid, u8 enabled_tc,
-				bool default_port, u16 *veb_seid,
-				bool enable_stats,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_add_veb(struct i40e_hw *hw, u16 uplink_seid,
+		    u16 downlink_seid, u8 enabled_tc,
+		    bool default_port, u16 *veb_seid,
+		    bool enable_stats,
+		    struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_veb *cmd =
 		(struct i40e_aqc_add_veb *)&desc.params.raw;
 	struct i40e_aqc_add_veb_completion *resp =
 		(struct i40e_aqc_add_veb_completion *)&desc.params.raw;
-	i40e_status status;
 	u16 veb_flags = 0;
+	int status;
 
 	/* SEIDs need to either both be set or both be 0 for floating VEB */
 	if (!!uplink_seid != !!downlink_seid)
@@ -2585,17 +2440,17 @@
  * This retrieves the parameters for a particular VEB, specified by
  * uplink_seid, and returns them to the caller.
  **/
-i40e_status i40e_aq_get_veb_parameters(struct i40e_hw *hw,
-				u16 veb_seid, u16 *switch_id,
-				bool *floating, u16 *statistic_index,
-				u16 *vebs_used, u16 *vebs_free,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_veb_parameters(struct i40e_hw *hw,
+			       u16 veb_seid, u16 *switch_id,
+			       bool *floating, u16 *statistic_index,
+			       u16 *vebs_used, u16 *vebs_free,
+			       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_get_veb_parameters_completion *cmd_resp =
 		(struct i40e_aqc_get_veb_parameters_completion *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (veb_seid == 0)
 		return I40E_ERR_PARAM;
@@ -2639,14 +2494,14 @@
  *
  * Add MAC/VLAN addresses to the HW filtering
  **/
-i40e_status i40e_aq_add_macvlan(struct i40e_hw *hw, u16 seid,
+int i40e_aq_add_macvlan(struct i40e_hw *hw, u16 seid,
 			struct i40e_aqc_add_macvlan_element_data *mv_list,
 			u16 count, struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_macvlan *cmd =
 		(struct i40e_aqc_macvlan *)&desc.params.raw;
-	i40e_status status;
+	int status;
 	u16 buf_size;
 	int i;
 
@@ -2687,15 +2542,16 @@
  *
  * Remove MAC/VLAN addresses from the HW filtering
  **/
-i40e_status i40e_aq_remove_macvlan(struct i40e_hw *hw, u16 seid,
-			struct i40e_aqc_remove_macvlan_element_data *mv_list,
-			u16 count, struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_remove_macvlan(struct i40e_hw *hw, u16 seid,
+		       struct i40e_aqc_remove_macvlan_element_data *mv_list,
+		       u16 count, struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_macvlan *cmd =
 		(struct i40e_aqc_macvlan *)&desc.params.raw;
-	i40e_status status;
 	u16 buf_size;
+	int status;
 
 	if (count == 0 || !mv_list || !hw)
 		return I40E_ERR_PARAM;
@@ -2736,19 +2592,19 @@
  * Add/Delete a mirror rule to a specific switch. Mirror rules are supported for
  * VEBs/VEPA elements only
  **/
-static i40e_status i40e_mirrorrule_op(struct i40e_hw *hw,
-				u16 opcode, u16 sw_seid, u16 rule_type, u16 id,
-				u16 count, __le16 *mr_list,
-				struct i40e_asq_cmd_details *cmd_details,
-				u16 *rule_id, u16 *rules_used, u16 *rules_free)
+static int i40e_mirrorrule_op(struct i40e_hw *hw,
+			      u16 opcode, u16 sw_seid, u16 rule_type, u16 id,
+			      u16 count, __le16 *mr_list,
+			      struct i40e_asq_cmd_details *cmd_details,
+			      u16 *rule_id, u16 *rules_used, u16 *rules_free)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_delete_mirror_rule *cmd =
 		(struct i40e_aqc_add_delete_mirror_rule *)&desc.params.raw;
 	struct i40e_aqc_add_delete_mirror_rule_completion *resp =
 	(struct i40e_aqc_add_delete_mirror_rule_completion *)&desc.params.raw;
-	i40e_status status;
 	u16 buf_size;
+	int status;
 
 	buf_size = count * sizeof(*mr_list);
 
@@ -2796,10 +2652,11 @@
  *
  * Add mirror rule. Mirror rules are supported for VEBs or VEPA elements only
  **/
-i40e_status i40e_aq_add_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
-			u16 rule_type, u16 dest_vsi, u16 count, __le16 *mr_list,
-			struct i40e_asq_cmd_details *cmd_details,
-			u16 *rule_id, u16 *rules_used, u16 *rules_free)
+int i40e_aq_add_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
+			   u16 rule_type, u16 dest_vsi, u16 count,
+			   __le16 *mr_list,
+			   struct i40e_asq_cmd_details *cmd_details,
+			   u16 *rule_id, u16 *rules_used, u16 *rules_free)
 {
 	if (!(rule_type == I40E_AQC_MIRROR_RULE_TYPE_ALL_INGRESS ||
 	    rule_type == I40E_AQC_MIRROR_RULE_TYPE_ALL_EGRESS)) {
@@ -2827,10 +2684,11 @@
  *
  * Delete a mirror rule. Mirror rules are supported for VEBs/VEPA elements only
  **/
-i40e_status i40e_aq_delete_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
-			u16 rule_type, u16 rule_id, u16 count, __le16 *mr_list,
-			struct i40e_asq_cmd_details *cmd_details,
-			u16 *rules_used, u16 *rules_free)
+int i40e_aq_delete_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
+			      u16 rule_type, u16 rule_id, u16 count,
+			      __le16 *mr_list,
+			      struct i40e_asq_cmd_details *cmd_details,
+			      u16 *rules_used, u16 *rules_free)
 {
 	/* Rule ID has to be valid except rule_type: INGRESS VLAN mirroring */
 	if (rule_type == I40E_AQC_MIRROR_RULE_TYPE_VLAN) {
@@ -2859,14 +2717,14 @@
  *
  * send msg to vf
  **/
-i40e_status i40e_aq_send_msg_to_vf(struct i40e_hw *hw, u16 vfid,
-				u32 v_opcode, u32 v_retval, u8 *msg, u16 msglen,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_send_msg_to_vf(struct i40e_hw *hw, u16 vfid,
+			   u32 v_opcode, u32 v_retval, u8 *msg, u16 msglen,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_pf_vf_message *cmd =
 		(struct i40e_aqc_pf_vf_message *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_send_msg_to_vf);
 	cmd->id = cpu_to_le32(vfid);
@@ -2894,14 +2752,14 @@
  *
  * Read the register using the admin queue commands
  **/
-i40e_status i40e_aq_debug_read_register(struct i40e_hw *hw,
+int i40e_aq_debug_read_register(struct i40e_hw *hw,
 				u32 reg_addr, u64 *reg_val,
 				struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_debug_reg_read_write *cmd_resp =
 		(struct i40e_aqc_debug_reg_read_write *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (reg_val == NULL)
 		return I40E_ERR_PARAM;
@@ -2929,14 +2787,14 @@
  *
  * Write to a register using the admin queue commands
  **/
-i40e_status i40e_aq_debug_write_register(struct i40e_hw *hw,
-					u32 reg_addr, u64 reg_val,
-					struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_debug_write_register(struct i40e_hw *hw,
+				 u32 reg_addr, u64 reg_val,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_debug_reg_read_write *cmd =
 		(struct i40e_aqc_debug_reg_read_write *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_debug_write_reg);
 
@@ -2960,16 +2818,16 @@
  *
  * requests common resource using the admin queue commands
  **/
-i40e_status i40e_aq_request_resource(struct i40e_hw *hw,
-				enum i40e_aq_resources_ids resource,
-				enum i40e_aq_resource_access_type access,
-				u8 sdp_number, u64 *timeout,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_request_resource(struct i40e_hw *hw,
+			     enum i40e_aq_resources_ids resource,
+			     enum i40e_aq_resource_access_type access,
+			     u8 sdp_number, u64 *timeout,
+			     struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_request_resource *cmd_resp =
 		(struct i40e_aqc_request_resource *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_request_resource);
 
@@ -2999,15 +2857,15 @@
  *
  * release common resource using the admin queue commands
  **/
-i40e_status i40e_aq_release_resource(struct i40e_hw *hw,
-				enum i40e_aq_resources_ids resource,
-				u8 sdp_number,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_release_resource(struct i40e_hw *hw,
+			     enum i40e_aq_resources_ids resource,
+			     u8 sdp_number,
+			     struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_request_resource *cmd =
 		(struct i40e_aqc_request_resource *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_release_resource);
 
@@ -3031,15 +2889,15 @@
  *
  * Read the NVM using the admin queue commands
  **/
-i40e_status i40e_aq_read_nvm(struct i40e_hw *hw, u8 module_pointer,
-				u32 offset, u16 length, void *data,
-				bool last_command,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_read_nvm(struct i40e_hw *hw, u8 module_pointer,
+		     u32 offset, u16 length, void *data,
+		     bool last_command,
+		     struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_nvm_update *cmd =
 		(struct i40e_aqc_nvm_update *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	/* In offset the highest byte must be zeroed. */
 	if (offset & 0xFF000000) {
@@ -3077,14 +2935,14 @@
  *
  * Erase the NVM sector using the admin queue commands
  **/
-i40e_status i40e_aq_erase_nvm(struct i40e_hw *hw, u8 module_pointer,
-			      u32 offset, u16 length, bool last_command,
-			      struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_erase_nvm(struct i40e_hw *hw, u8 module_pointer,
+		      u32 offset, u16 length, bool last_command,
+		      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_nvm_update *cmd =
 		(struct i40e_aqc_nvm_update *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	/* In offset the highest byte must be zeroed. */
 	if (offset & 0xFF000000) {
@@ -3125,8 +2983,8 @@
 	u32 number, logical_id, phys_id;
 	struct i40e_hw_capabilities *p;
 	u16 id, ocp_cfg_word0;
-	i40e_status status;
 	u8 major_rev;
+	int status;
 	u32 i = 0;
 
 	cap = (struct i40e_aqc_list_capabilities_element_resp *) buff;
@@ -3367,14 +3225,14 @@
  *
  * Get the device capabilities descriptions from the firmware
  **/
-i40e_status i40e_aq_discover_capabilities(struct i40e_hw *hw,
-				void *buff, u16 buff_size, u16 *data_size,
-				enum i40e_admin_queue_opc list_type_opc,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_discover_capabilities(struct i40e_hw *hw,
+				  void *buff, u16 buff_size, u16 *data_size,
+				  enum i40e_admin_queue_opc list_type_opc,
+				  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aqc_list_capabilites *cmd;
 	struct i40e_aq_desc desc;
-	i40e_status status = 0;
+	int status = 0;
 
 	cmd = (struct i40e_aqc_list_capabilites *)&desc.params.raw;
 
@@ -3416,15 +3274,15 @@
  *
  * Update the NVM using the admin queue commands
  **/
-i40e_status i40e_aq_update_nvm(struct i40e_hw *hw, u8 module_pointer,
-			       u32 offset, u16 length, void *data,
-				bool last_command, u8 preservation_flags,
-			       struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_update_nvm(struct i40e_hw *hw, u8 module_pointer,
+		       u32 offset, u16 length, void *data,
+		       bool last_command, u8 preservation_flags,
+		       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_nvm_update *cmd =
 		(struct i40e_aqc_nvm_update *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	/* In offset the highest byte must be zeroed. */
 	if (offset & 0xFF000000) {
@@ -3469,13 +3327,13 @@
  *
  * Rearrange NVM structure, available only for transition FW
  **/
-i40e_status i40e_aq_rearrange_nvm(struct i40e_hw *hw,
-				  u8 rearrange_nvm,
-				  struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_rearrange_nvm(struct i40e_hw *hw,
+			  u8 rearrange_nvm,
+			  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aqc_nvm_update *cmd;
-	i40e_status status;
 	struct i40e_aq_desc desc;
+	int status;
 
 	cmd = (struct i40e_aqc_nvm_update *)&desc.params.raw;
 
@@ -3509,17 +3367,17 @@
  *
  * Requests the complete LLDP MIB (entire packet).
  **/
-i40e_status i40e_aq_get_lldp_mib(struct i40e_hw *hw, u8 bridge_type,
-				u8 mib_type, void *buff, u16 buff_size,
-				u16 *local_len, u16 *remote_len,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_lldp_mib(struct i40e_hw *hw, u8 bridge_type,
+			 u8 mib_type, void *buff, u16 buff_size,
+			 u16 *local_len, u16 *remote_len,
+			 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_lldp_get_mib *cmd =
 		(struct i40e_aqc_lldp_get_mib *)&desc.params.raw;
 	struct i40e_aqc_lldp_get_mib *resp =
 		(struct i40e_aqc_lldp_get_mib *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (buff_size == 0 || !buff)
 		return I40E_ERR_PARAM;
@@ -3559,14 +3417,14 @@
  *
  * Set the LLDP MIB.
  **/
-enum i40e_status_code
+int
 i40e_aq_set_lldp_mib(struct i40e_hw *hw,
 		     u8 mib_type, void *buff, u16 buff_size,
 		     struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aqc_lldp_set_local_mib *cmd;
-	enum i40e_status_code status;
 	struct i40e_aq_desc desc;
+	int status;
 
 	cmd = (struct i40e_aqc_lldp_set_local_mib *)&desc.params.raw;
 	if (buff_size == 0 || !buff)
@@ -3598,14 +3456,14 @@
  * Enable or Disable posting of an event on ARQ when LLDP MIB
  * associated with the interface changes
  **/
-i40e_status i40e_aq_cfg_lldp_mib_change_event(struct i40e_hw *hw,
-				bool enable_update,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_cfg_lldp_mib_change_event(struct i40e_hw *hw,
+				      bool enable_update,
+				      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_lldp_update_mib *cmd =
 		(struct i40e_aqc_lldp_update_mib *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_lldp_update_mib);
 
@@ -3627,14 +3485,14 @@
  * Restore LLDP Agent factory settings if @restore set to True. In other case
  * only returns factory setting in AQ response.
  **/
-enum i40e_status_code
+int
 i40e_aq_restore_lldp(struct i40e_hw *hw, u8 *setting, bool restore,
 		     struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_lldp_restore *cmd =
 		(struct i40e_aqc_lldp_restore *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (!(hw->flags & I40E_HW_FLAG_FW_LLDP_PERSISTENT)) {
 		i40e_debug(hw, I40E_DEBUG_ALL,
@@ -3664,14 +3522,14 @@
  *
  * Stop or Shutdown the embedded LLDP Agent
  **/
-i40e_status i40e_aq_stop_lldp(struct i40e_hw *hw, bool shutdown_agent,
-				bool persist,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_stop_lldp(struct i40e_hw *hw, bool shutdown_agent,
+		      bool persist,
+		      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_lldp_stop *cmd =
 		(struct i40e_aqc_lldp_stop *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_lldp_stop);
 
@@ -3699,13 +3557,13 @@
  *
  * Start the embedded LLDP Agent on all ports.
  **/
-i40e_status i40e_aq_start_lldp(struct i40e_hw *hw, bool persist,
-			       struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_start_lldp(struct i40e_hw *hw, bool persist,
+		       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_lldp_start *cmd =
 		(struct i40e_aqc_lldp_start *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_lldp_start);
 
@@ -3731,14 +3589,14 @@
  * @dcb_enable: True if DCB configuration needs to be applied
  *
  **/
-enum i40e_status_code
+int
 i40e_aq_set_dcb_parameters(struct i40e_hw *hw, bool dcb_enable,
 			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_set_dcb_parameters *cmd =
 		(struct i40e_aqc_set_dcb_parameters *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (!(hw->flags & I40E_HW_FLAG_FW_LLDP_STOPPABLE))
 		return I40E_ERR_DEVICE_NOT_SUPPORTED;
@@ -3764,12 +3622,12 @@
  *
  * Get CEE DCBX mode operational configuration from firmware
  **/
-i40e_status i40e_aq_get_cee_dcb_config(struct i40e_hw *hw,
-				       void *buff, u16 buff_size,
-				       struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_cee_dcb_config(struct i40e_hw *hw,
+			       void *buff, u16 buff_size,
+			       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
-	i40e_status status;
+	int status;
 
 	if (buff_size == 0 || !buff)
 		return I40E_ERR_PARAM;
@@ -3795,17 +3653,17 @@
  * and this function will call cpu_to_le16 to convert from Host byte order to
  * Little Endian order.
  **/
-i40e_status i40e_aq_add_udp_tunnel(struct i40e_hw *hw,
-				u16 udp_port, u8 protocol_index,
-				u8 *filter_index,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_add_udp_tunnel(struct i40e_hw *hw,
+			   u16 udp_port, u8 protocol_index,
+			   u8 *filter_index,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_udp_tunnel *cmd =
 		(struct i40e_aqc_add_udp_tunnel *)&desc.params.raw;
 	struct i40e_aqc_del_udp_tunnel_completion *resp =
 		(struct i40e_aqc_del_udp_tunnel_completion *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_add_udp_tunnel);
 
@@ -3826,13 +3684,13 @@
  * @index: filter index
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_del_udp_tunnel(struct i40e_hw *hw, u8 index,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_del_udp_tunnel(struct i40e_hw *hw, u8 index,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_remove_udp_tunnel *cmd =
 		(struct i40e_aqc_remove_udp_tunnel *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_del_udp_tunnel);
 
@@ -3851,13 +3709,13 @@
  *
  * This deletes a switch element from the switch.
  **/
-i40e_status i40e_aq_delete_element(struct i40e_hw *hw, u16 seid,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_delete_element(struct i40e_hw *hw, u16 seid,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_switch_seid *cmd =
 		(struct i40e_aqc_switch_seid *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (seid == 0)
 		return I40E_ERR_PARAM;
@@ -3880,11 +3738,11 @@
  * recomputed and modified. The retval field in the descriptor
  * will be set to 0 when RPB is modified.
  **/
-i40e_status i40e_aq_dcb_updated(struct i40e_hw *hw,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_dcb_updated(struct i40e_hw *hw,
+			struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_dcb_updated);
 
@@ -3904,15 +3762,15 @@
  *
  * Generic command handler for Tx scheduler AQ commands
  **/
-static i40e_status i40e_aq_tx_sched_cmd(struct i40e_hw *hw, u16 seid,
+static int i40e_aq_tx_sched_cmd(struct i40e_hw *hw, u16 seid,
 				void *buff, u16 buff_size,
-				 enum i40e_admin_queue_opc opcode,
+				enum i40e_admin_queue_opc opcode,
 				struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_tx_sched_ind *cmd =
 		(struct i40e_aqc_tx_sched_ind *)&desc.params.raw;
-	i40e_status status;
+	int status;
 	bool cmd_param_flag = false;
 
 	switch (opcode) {
@@ -3962,14 +3820,14 @@
  * @max_credit: Max BW limit credits
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_config_vsi_bw_limit(struct i40e_hw *hw,
+int i40e_aq_config_vsi_bw_limit(struct i40e_hw *hw,
 				u16 seid, u16 credit, u8 max_credit,
 				struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_configure_vsi_bw_limit *cmd =
 		(struct i40e_aqc_configure_vsi_bw_limit *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_configure_vsi_bw_limit);
@@ -3990,10 +3848,10 @@
  * @bw_data: Buffer holding enabled TCs, relative TC BW limit/credits
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_config_vsi_tc_bw(struct i40e_hw *hw,
-			u16 seid,
-			struct i40e_aqc_configure_vsi_tc_bw_data *bw_data,
-			struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_config_vsi_tc_bw(struct i40e_hw *hw,
+			     u16 seid,
+			     struct i40e_aqc_configure_vsi_tc_bw_data *bw_data,
+			     struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)bw_data, sizeof(*bw_data),
 				    i40e_aqc_opc_configure_vsi_tc_bw,
@@ -4008,11 +3866,12 @@
  * @opcode: Tx scheduler AQ command opcode
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_config_switch_comp_ets(struct i40e_hw *hw,
-		u16 seid,
-		struct i40e_aqc_configure_switching_comp_ets_data *ets_data,
-		enum i40e_admin_queue_opc opcode,
-		struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_config_switch_comp_ets(struct i40e_hw *hw,
+			       u16 seid,
+			       struct i40e_aqc_configure_switching_comp_ets_data *ets_data,
+			       enum i40e_admin_queue_opc opcode,
+			       struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)ets_data,
 				    sizeof(*ets_data), opcode, cmd_details);
@@ -4025,7 +3884,8 @@
  * @bw_data: Buffer holding enabled TCs, relative/absolute TC BW limit/credits
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_config_switch_comp_bw_config(struct i40e_hw *hw,
+int
+i40e_aq_config_switch_comp_bw_config(struct i40e_hw *hw,
 	u16 seid,
 	struct i40e_aqc_configure_switching_comp_bw_config_data *bw_data,
 	struct i40e_asq_cmd_details *cmd_details)
@@ -4042,10 +3902,11 @@
  * @bw_data: Buffer to hold VSI BW configuration
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_query_vsi_bw_config(struct i40e_hw *hw,
-			u16 seid,
-			struct i40e_aqc_query_vsi_bw_config_resp *bw_data,
-			struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_query_vsi_bw_config(struct i40e_hw *hw,
+			    u16 seid,
+			    struct i40e_aqc_query_vsi_bw_config_resp *bw_data,
+			    struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)bw_data, sizeof(*bw_data),
 				    i40e_aqc_opc_query_vsi_bw_config,
@@ -4059,10 +3920,11 @@
  * @bw_data: Buffer to hold VSI BW configuration per TC
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_query_vsi_ets_sla_config(struct i40e_hw *hw,
-			u16 seid,
-			struct i40e_aqc_query_vsi_ets_sla_config_resp *bw_data,
-			struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_query_vsi_ets_sla_config(struct i40e_hw *hw,
+				 u16 seid,
+				 struct i40e_aqc_query_vsi_ets_sla_config_resp *bw_data,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)bw_data, sizeof(*bw_data),
 				    i40e_aqc_opc_query_vsi_ets_sla_config,
@@ -4076,10 +3938,11 @@
  * @bw_data: Buffer to hold switching component's per TC BW config
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_query_switch_comp_ets_config(struct i40e_hw *hw,
-		u16 seid,
-		struct i40e_aqc_query_switching_comp_ets_config_resp *bw_data,
-		struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_query_switch_comp_ets_config(struct i40e_hw *hw,
+				     u16 seid,
+				     struct i40e_aqc_query_switching_comp_ets_config_resp *bw_data,
+				     struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)bw_data, sizeof(*bw_data),
 				   i40e_aqc_opc_query_switching_comp_ets_config,
@@ -4093,10 +3956,11 @@
  * @bw_data: Buffer to hold current ETS configuration for the Physical Port
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_query_port_ets_config(struct i40e_hw *hw,
-			u16 seid,
-			struct i40e_aqc_query_port_ets_config_resp *bw_data,
-			struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_query_port_ets_config(struct i40e_hw *hw,
+			      u16 seid,
+			      struct i40e_aqc_query_port_ets_config_resp *bw_data,
+			      struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)bw_data, sizeof(*bw_data),
 				    i40e_aqc_opc_query_port_ets_config,
@@ -4110,10 +3974,11 @@
  * @bw_data: Buffer to hold switching component's BW configuration
  * @cmd_details: pointer to command details structure or NULL
  **/
-i40e_status i40e_aq_query_switch_comp_bw_config(struct i40e_hw *hw,
-		u16 seid,
-		struct i40e_aqc_query_switching_comp_bw_config_resp *bw_data,
-		struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_query_switch_comp_bw_config(struct i40e_hw *hw,
+				    u16 seid,
+				    struct i40e_aqc_query_switching_comp_bw_config_resp *bw_data,
+				    struct i40e_asq_cmd_details *cmd_details)
 {
 	return i40e_aq_tx_sched_cmd(hw, seid, (void *)bw_data, sizeof(*bw_data),
 				    i40e_aqc_opc_query_switching_comp_bw_config,
@@ -4132,8 +3997,9 @@
  * Returns 0 if the values passed are valid and within
  * range else returns an error.
  **/
-static i40e_status i40e_validate_filter_settings(struct i40e_hw *hw,
-				struct i40e_filter_control_settings *settings)
+static int
+i40e_validate_filter_settings(struct i40e_hw *hw,
+			      struct i40e_filter_control_settings *settings)
 {
 	u32 fcoe_cntx_size, fcoe_filt_size;
 	u32 pe_cntx_size, pe_filt_size;
@@ -4224,11 +4090,11 @@
  * for a single PF. It is expected that these settings are programmed
  * at the driver initialization time.
  **/
-i40e_status i40e_set_filter_control(struct i40e_hw *hw,
-				struct i40e_filter_control_settings *settings)
+int i40e_set_filter_control(struct i40e_hw *hw,
+			    struct i40e_filter_control_settings *settings)
 {
-	i40e_status ret = 0;
 	u32 hash_lut_size = 0;
+	int ret = 0;
 	u32 val;
 
 	if (!settings)
@@ -4298,11 +4164,11 @@
  * In return it will update the total number of perfect filter count in
  * the stats member.
  **/
-i40e_status i40e_aq_add_rem_control_packet_filter(struct i40e_hw *hw,
-				u8 *mac_addr, u16 ethtype, u16 flags,
-				u16 vsi_seid, u16 queue, bool is_add,
-				struct i40e_control_filter_stats *stats,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_add_rem_control_packet_filter(struct i40e_hw *hw,
+					  u8 *mac_addr, u16 ethtype, u16 flags,
+					  u16 vsi_seid, u16 queue, bool is_add,
+					  struct i40e_control_filter_stats *stats,
+					  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_remove_control_packet_filter *cmd =
@@ -4311,7 +4177,7 @@
 	struct i40e_aqc_add_remove_control_packet_filter_completion *resp =
 		(struct i40e_aqc_add_remove_control_packet_filter_completion *)
 		&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (vsi_seid == 0)
 		return I40E_ERR_PARAM;
@@ -4357,7 +4223,7 @@
 		   I40E_AQC_ADD_CONTROL_PACKET_FLAGS_DROP |
 		   I40E_AQC_ADD_CONTROL_PACKET_FLAGS_TX;
 	u16 ethtype = I40E_FLOW_CONTROL_ETHTYPE;
-	i40e_status status;
+	int status;
 
 	status = i40e_aq_add_rem_control_packet_filter(hw, NULL, ethtype, flag,
 						       seid, 0, true, NULL,
@@ -4379,14 +4245,14 @@
  * is not passed then only register at 'reg_addr0' is read.
  *
  **/
-static i40e_status i40e_aq_alternate_read(struct i40e_hw *hw,
-					  u32 reg_addr0, u32 *reg_val0,
-					  u32 reg_addr1, u32 *reg_val1)
+static int i40e_aq_alternate_read(struct i40e_hw *hw,
+				  u32 reg_addr0, u32 *reg_val0,
+				  u32 reg_addr1, u32 *reg_val1)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_alternate_write *cmd_resp =
 		(struct i40e_aqc_alternate_write *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (!reg_val0)
 		return I40E_ERR_PARAM;
@@ -4415,12 +4281,12 @@
  *
  * Suspend port's Tx traffic
  **/
-i40e_status i40e_aq_suspend_port_tx(struct i40e_hw *hw, u16 seid,
-				    struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_suspend_port_tx(struct i40e_hw *hw, u16 seid,
+			    struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aqc_tx_sched_ind *cmd;
 	struct i40e_aq_desc desc;
-	i40e_status status;
+	int status;
 
 	cmd = (struct i40e_aqc_tx_sched_ind *)&desc.params.raw;
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_suspend_port_tx);
@@ -4437,11 +4303,11 @@
  *
  * Resume port's Tx traffic
  **/
-i40e_status i40e_aq_resume_port_tx(struct i40e_hw *hw,
-				   struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_resume_port_tx(struct i40e_hw *hw,
+			   struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_resume_port_tx);
 
@@ -4511,18 +4377,18 @@
  * Dump internal FW/HW data for debug purposes.
  *
  **/
-i40e_status i40e_aq_debug_dump(struct i40e_hw *hw, u8 cluster_id,
-			       u8 table_id, u32 start_index, u16 buff_size,
-			       void *buff, u16 *ret_buff_size,
-			       u8 *ret_next_table, u32 *ret_next_index,
-			       struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_debug_dump(struct i40e_hw *hw, u8 cluster_id,
+		       u8 table_id, u32 start_index, u16 buff_size,
+		       void *buff, u16 *ret_buff_size,
+		       u8 *ret_next_table, u32 *ret_next_index,
+		       struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_debug_dump_internals *cmd =
 		(struct i40e_aqc_debug_dump_internals *)&desc.params.raw;
 	struct i40e_aqc_debug_dump_internals *resp =
 		(struct i40e_aqc_debug_dump_internals *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (buff_size == 0 || !buff)
 		return I40E_ERR_PARAM;
@@ -4563,12 +4429,12 @@
  *
  * Read bw from the alternate ram for the given pf
  **/
-i40e_status i40e_read_bw_from_alt_ram(struct i40e_hw *hw,
-				      u32 *max_bw, u32 *min_bw,
-				      bool *min_valid, bool *max_valid)
+int i40e_read_bw_from_alt_ram(struct i40e_hw *hw,
+			      u32 *max_bw, u32 *min_bw,
+			      bool *min_valid, bool *max_valid)
 {
-	i40e_status status;
 	u32 max_bw_addr, min_bw_addr;
+	int status;
 
 	/* Calculate the address of the min/max bw registers */
 	max_bw_addr = I40E_ALT_STRUCT_FIRST_PF_OFFSET +
@@ -4603,13 +4469,14 @@
  *
  * Configure partitions guaranteed/max bw
  **/
-i40e_status i40e_aq_configure_partition_bw(struct i40e_hw *hw,
-			struct i40e_aqc_configure_partition_bw_data *bw_data,
-			struct i40e_asq_cmd_details *cmd_details)
+int
+i40e_aq_configure_partition_bw(struct i40e_hw *hw,
+			       struct i40e_aqc_configure_partition_bw_data *bw_data,
+			       struct i40e_asq_cmd_details *cmd_details)
 {
-	i40e_status status;
-	struct i40e_aq_desc desc;
 	u16 bwd_size = sizeof(*bw_data);
+	struct i40e_aq_desc desc;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_configure_partition_bw);
@@ -4638,11 +4505,11 @@
  *
  * Reads specified PHY register value
  **/
-i40e_status i40e_read_phy_register_clause22(struct i40e_hw *hw,
-					    u16 reg, u8 phy_addr, u16 *value)
+int i40e_read_phy_register_clause22(struct i40e_hw *hw,
+				    u16 reg, u8 phy_addr, u16 *value)
 {
-	i40e_status status = I40E_ERR_TIMEOUT;
 	u8 port_num = (u8)hw->func_caps.mdio_port_num;
+	int status = I40E_ERR_TIMEOUT;
 	u32 command = 0;
 	u16 retry = 1000;
 
@@ -4683,11 +4550,11 @@
  *
  * Writes specified PHY register value
  **/
-i40e_status i40e_write_phy_register_clause22(struct i40e_hw *hw,
-					     u16 reg, u8 phy_addr, u16 value)
+int i40e_write_phy_register_clause22(struct i40e_hw *hw,
+				     u16 reg, u8 phy_addr, u16 value)
 {
-	i40e_status status = I40E_ERR_TIMEOUT;
 	u8 port_num = (u8)hw->func_caps.mdio_port_num;
+	int status = I40E_ERR_TIMEOUT;
 	u32 command  = 0;
 	u16 retry = 1000;
 
@@ -4724,13 +4591,13 @@
  *
  * Reads specified PHY register value
  **/
-i40e_status i40e_read_phy_register_clause45(struct i40e_hw *hw,
-				u8 page, u16 reg, u8 phy_addr, u16 *value)
+int i40e_read_phy_register_clause45(struct i40e_hw *hw,
+				    u8 page, u16 reg, u8 phy_addr, u16 *value)
 {
-	i40e_status status = I40E_ERR_TIMEOUT;
+	u8 port_num = hw->func_caps.mdio_port_num;
+	int status = I40E_ERR_TIMEOUT;
 	u32 command = 0;
 	u16 retry = 1000;
-	u8 port_num = hw->func_caps.mdio_port_num;
 
 	command = (reg << I40E_GLGEN_MSCA_MDIADD_SHIFT) |
 		  (page << I40E_GLGEN_MSCA_DEVADD_SHIFT) |
@@ -4798,13 +4665,13 @@
  *
  * Writes value to specified PHY register
  **/
-i40e_status i40e_write_phy_register_clause45(struct i40e_hw *hw,
-				u8 page, u16 reg, u8 phy_addr, u16 value)
+int i40e_write_phy_register_clause45(struct i40e_hw *hw,
+				     u8 page, u16 reg, u8 phy_addr, u16 value)
 {
-	i40e_status status = I40E_ERR_TIMEOUT;
-	u32 command = 0;
-	u16 retry = 1000;
 	u8 port_num = hw->func_caps.mdio_port_num;
+	int status = I40E_ERR_TIMEOUT;
+	u16 retry = 1000;
+	u32 command = 0;
 
 	command = (reg << I40E_GLGEN_MSCA_MDIADD_SHIFT) |
 		  (page << I40E_GLGEN_MSCA_DEVADD_SHIFT) |
@@ -4865,10 +4732,10 @@
  *
  * Writes value to specified PHY register
  **/
-i40e_status i40e_write_phy_register(struct i40e_hw *hw,
-				    u8 page, u16 reg, u8 phy_addr, u16 value)
+int i40e_write_phy_register(struct i40e_hw *hw,
+			    u8 page, u16 reg, u8 phy_addr, u16 value)
 {
-	i40e_status status;
+	int status;
 
 	switch (hw->device_id) {
 	case I40E_DEV_ID_1G_BASE_T_X722:
@@ -4903,10 +4770,10 @@
  *
  * Reads specified PHY register value
  **/
-i40e_status i40e_read_phy_register(struct i40e_hw *hw,
-				   u8 page, u16 reg, u8 phy_addr, u16 *value)
+int i40e_read_phy_register(struct i40e_hw *hw,
+			   u8 page, u16 reg, u8 phy_addr, u16 *value)
 {
-	i40e_status status;
+	int status;
 
 	switch (hw->device_id) {
 	case I40E_DEV_ID_1G_BASE_T_X722:
@@ -4954,17 +4821,17 @@
  *
  * Blinks PHY link LED
  **/
-i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
-				    u32 time, u32 interval)
+int i40e_blink_phy_link_led(struct i40e_hw *hw,
+			    u32 time, u32 interval)
 {
-	i40e_status status = 0;
-	u32 i;
-	u16 led_ctl;
-	u16 gpio_led_port;
-	u16 led_reg;
 	u16 led_addr = I40E_PHY_LED_PROV_REG_1;
+	u16 gpio_led_port;
 	u8 phy_addr = 0;
+	int status = 0;
+	u16 led_ctl;
 	u8 port_num;
+	u16 led_reg;
+	u32 i;
 
 	i = rd32(hw, I40E_PFGEN_PORTNUM);
 	port_num = (u8)(i & I40E_PFGEN_PORTNUM_PORT_NUM_MASK);
@@ -5026,12 +4893,12 @@
  * @led_addr: LED register address
  * @reg_val: read register value
  **/
-static enum i40e_status_code i40e_led_get_reg(struct i40e_hw *hw, u16 led_addr,
-					      u32 *reg_val)
+static int i40e_led_get_reg(struct i40e_hw *hw, u16 led_addr,
+			    u32 *reg_val)
 {
-	enum i40e_status_code status;
 	u8 phy_addr = 0;
 	u8 port_num;
+	int status;
 	u32 i;
 
 	*reg_val = 0;
@@ -5060,12 +4927,12 @@
  * @led_addr: LED register address
  * @reg_val: register value to write
  **/
-static enum i40e_status_code i40e_led_set_reg(struct i40e_hw *hw, u16 led_addr,
-					      u32 reg_val)
+static int i40e_led_set_reg(struct i40e_hw *hw, u16 led_addr,
+			    u32 reg_val)
 {
-	enum i40e_status_code status;
 	u8 phy_addr = 0;
 	u8 port_num;
+	int status;
 	u32 i;
 
 	if (hw->flags & I40E_HW_FLAG_AQ_PHY_ACCESS_CAPABLE) {
@@ -5095,17 +4962,17 @@
  * @val: original value of register to use
  *
  **/
-i40e_status i40e_led_get_phy(struct i40e_hw *hw, u16 *led_addr,
-			     u16 *val)
+int i40e_led_get_phy(struct i40e_hw *hw, u16 *led_addr,
+		     u16 *val)
 {
-	i40e_status status = 0;
 	u16 gpio_led_port;
 	u8 phy_addr = 0;
-	u16 reg_val;
+	u32 reg_val_aq;
+	int status = 0;
 	u16 temp_addr;
+	u16 reg_val;
 	u8 port_num;
 	u32 i;
-	u32 reg_val_aq;
 
 	if (hw->flags & I40E_HW_FLAG_AQ_PHY_ACCESS_CAPABLE) {
 		status =
@@ -5150,12 +5017,12 @@
  * Set led's on or off when controlled by the PHY
  *
  **/
-i40e_status i40e_led_set_phy(struct i40e_hw *hw, bool on,
-			     u16 led_addr, u32 mode)
+int i40e_led_set_phy(struct i40e_hw *hw, bool on,
+		     u16 led_addr, u32 mode)
 {
-	i40e_status status = 0;
 	u32 led_ctl = 0;
 	u32 led_reg = 0;
+	int status = 0;
 
 	status = i40e_led_get_reg(hw, led_addr, &led_reg);
 	if (status)
@@ -5199,14 +5066,14 @@
  * Use the firmware to read the Rx control register,
  * especially useful if the Rx unit is under heavy pressure
  **/
-i40e_status i40e_aq_rx_ctl_read_register(struct i40e_hw *hw,
-				u32 reg_addr, u32 *reg_val,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_rx_ctl_read_register(struct i40e_hw *hw,
+				 u32 reg_addr, u32 *reg_val,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_rx_ctl_reg_read_write *cmd_resp =
 		(struct i40e_aqc_rx_ctl_reg_read_write *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	if (!reg_val)
 		return I40E_ERR_PARAM;
@@ -5230,8 +5097,8 @@
  **/
 u32 i40e_read_rx_ctl(struct i40e_hw *hw, u32 reg_addr)
 {
-	i40e_status status = 0;
 	bool use_register;
+	int status = 0;
 	int retry = 5;
 	u32 val = 0;
 
@@ -5265,14 +5132,14 @@
  * Use the firmware to write to an Rx control register,
  * especially useful if the Rx unit is under heavy pressure
  **/
-i40e_status i40e_aq_rx_ctl_write_register(struct i40e_hw *hw,
-				u32 reg_addr, u32 reg_val,
-				struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_rx_ctl_write_register(struct i40e_hw *hw,
+				  u32 reg_addr, u32 reg_val,
+				  struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_rx_ctl_reg_read_write *cmd =
 		(struct i40e_aqc_rx_ctl_reg_read_write *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, i40e_aqc_opc_rx_ctl_reg_write);
 
@@ -5292,8 +5159,8 @@
  **/
 void i40e_write_rx_ctl(struct i40e_hw *hw, u32 reg_addr, u32 reg_val)
 {
-	i40e_status status = 0;
 	bool use_register;
+	int status = 0;
 	int retry = 5;
 
 	use_register = (((hw->aq.api_maj_ver == 1) &&
@@ -5355,16 +5222,16 @@
  * NOTE: In common cases MDIO I/F number should not be changed, thats why you
  * may use simple wrapper i40e_aq_set_phy_register.
  **/
-enum i40e_status_code i40e_aq_set_phy_register_ext(struct i40e_hw *hw,
-			     u8 phy_select, u8 dev_addr, bool page_change,
-			     bool set_mdio, u8 mdio_num,
-			     u32 reg_addr, u32 reg_val,
-			     struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_set_phy_register_ext(struct i40e_hw *hw,
+				 u8 phy_select, u8 dev_addr, bool page_change,
+				 bool set_mdio, u8 mdio_num,
+				 u32 reg_addr, u32 reg_val,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_phy_register_access *cmd =
 		(struct i40e_aqc_phy_register_access *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_set_phy_register);
@@ -5400,16 +5267,16 @@
  * NOTE: In common cases MDIO I/F number should not be changed, thats why you
  * may use simple wrapper i40e_aq_get_phy_register.
  **/
-enum i40e_status_code i40e_aq_get_phy_register_ext(struct i40e_hw *hw,
-			     u8 phy_select, u8 dev_addr, bool page_change,
-			     bool set_mdio, u8 mdio_num,
-			     u32 reg_addr, u32 *reg_val,
-			     struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_phy_register_ext(struct i40e_hw *hw,
+				 u8 phy_select, u8 dev_addr, bool page_change,
+				 bool set_mdio, u8 mdio_num,
+				 u32 reg_addr, u32 *reg_val,
+				 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_phy_register_access *cmd =
 		(struct i40e_aqc_phy_register_access *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_get_phy_register);
@@ -5440,18 +5307,17 @@
  * @error_info: returns error information
  * @cmd_details: pointer to command details structure or NULL
  **/
-enum
-i40e_status_code i40e_aq_write_ddp(struct i40e_hw *hw, void *buff,
-				   u16 buff_size, u32 track_id,
-				   u32 *error_offset, u32 *error_info,
-				   struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_write_ddp(struct i40e_hw *hw, void *buff,
+		      u16 buff_size, u32 track_id,
+		      u32 *error_offset, u32 *error_info,
+		      struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_write_personalization_profile *cmd =
 		(struct i40e_aqc_write_personalization_profile *)
 		&desc.params.raw;
 	struct i40e_aqc_write_ddp_resp *resp;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_write_personalization_profile);
@@ -5484,15 +5350,14 @@
  * @flags: AdminQ command flags
  * @cmd_details: pointer to command details structure or NULL
  **/
-enum
-i40e_status_code i40e_aq_get_ddp_list(struct i40e_hw *hw, void *buff,
-				      u16 buff_size, u8 flags,
-				      struct i40e_asq_cmd_details *cmd_details)
+int i40e_aq_get_ddp_list(struct i40e_hw *hw, void *buff,
+			 u16 buff_size, u8 flags,
+			 struct i40e_asq_cmd_details *cmd_details)
 {
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_get_applied_profiles *cmd =
 		(struct i40e_aqc_get_applied_profiles *)&desc.params.raw;
-	i40e_status status;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_get_personalization_profile_list);
@@ -5591,14 +5456,13 @@
  * @hw: pointer to the hw struct
  * @aq: command buffer containing all data to execute AQ
  **/
-static enum
-i40e_status_code i40e_ddp_exec_aq_section(struct i40e_hw *hw,
-					  struct i40e_profile_aq_section *aq)
+static int i40e_ddp_exec_aq_section(struct i40e_hw *hw,
+				    struct i40e_profile_aq_section *aq)
 {
-	i40e_status status;
 	struct i40e_aq_desc desc;
 	u8 *msg = NULL;
 	u16 msglen;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc, aq->opcode);
 	desc.flags |= cpu_to_le16(aq->flags);
@@ -5638,14 +5502,14 @@
  *
  * Validates supported devices and profile's sections.
  */
-static enum i40e_status_code
+static int
 i40e_validate_profile(struct i40e_hw *hw, struct i40e_profile_segment *profile,
 		      u32 track_id, bool rollback)
 {
 	struct i40e_profile_section_header *sec = NULL;
-	i40e_status status = 0;
 	struct i40e_section_table *sec_tbl;
 	u32 vendor_dev_id;
+	int status = 0;
 	u32 dev_cnt;
 	u32 sec_off;
 	u32 i;
@@ -5703,16 +5567,16 @@
  *
  * Handles the download of a complete package.
  */
-enum i40e_status_code
+int
 i40e_write_profile(struct i40e_hw *hw, struct i40e_profile_segment *profile,
 		   u32 track_id)
 {
-	i40e_status status = 0;
-	struct i40e_section_table *sec_tbl;
 	struct i40e_profile_section_header *sec = NULL;
 	struct i40e_profile_aq_section *ddp_aq;
-	u32 section_size = 0;
+	struct i40e_section_table *sec_tbl;
 	u32 offset = 0, info = 0;
+	u32 section_size = 0;
+	int status = 0;
 	u32 sec_off;
 	u32 i;
 
@@ -5766,15 +5630,15 @@
  *
  * Rolls back previously loaded package.
  */
-enum i40e_status_code
+int
 i40e_rollback_profile(struct i40e_hw *hw, struct i40e_profile_segment *profile,
 		      u32 track_id)
 {
 	struct i40e_profile_section_header *sec = NULL;
-	i40e_status status = 0;
 	struct i40e_section_table *sec_tbl;
 	u32 offset = 0, info = 0;
 	u32 section_size = 0;
+	int status = 0;
 	u32 sec_off;
 	int i;
 
@@ -5818,15 +5682,15 @@
  *
  * Register a profile to the list of loaded profiles.
  */
-enum i40e_status_code
+int
 i40e_add_pinfo_to_list(struct i40e_hw *hw,
 		       struct i40e_profile_segment *profile,
 		       u8 *profile_info_sec, u32 track_id)
 {
-	i40e_status status = 0;
 	struct i40e_profile_section_header *sec = NULL;
 	struct i40e_profile_info *pinfo;
 	u32 offset = 0, info = 0;
+	int status = 0;
 
 	sec = (struct i40e_profile_section_header *)profile_info_sec;
 	sec->tbl_size = 1;
@@ -5860,7 +5724,7 @@
  * of the function.
  *
  **/
-enum i40e_status_code
+int
 i40e_aq_add_cloud_filters(struct i40e_hw *hw, u16 seid,
 			  struct i40e_aqc_cloud_filters_element_data *filters,
 			  u8 filter_count)
@@ -5868,8 +5732,8 @@
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_remove_cloud_filters *cmd =
 	(struct i40e_aqc_add_remove_cloud_filters *)&desc.params.raw;
-	enum i40e_status_code status;
 	u16 buff_len;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_add_cloud_filters);
@@ -5897,7 +5761,7 @@
  * function.
  *
  **/
-enum i40e_status_code
+int
 i40e_aq_add_cloud_filters_bb(struct i40e_hw *hw, u16 seid,
 			     struct i40e_aqc_cloud_filters_element_bb *filters,
 			     u8 filter_count)
@@ -5905,8 +5769,8 @@
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_remove_cloud_filters *cmd =
 	(struct i40e_aqc_add_remove_cloud_filters *)&desc.params.raw;
-	i40e_status status;
 	u16 buff_len;
+	int status;
 	int i;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
@@ -5954,7 +5818,7 @@
  * of the function.
  *
  **/
-enum i40e_status_code
+int
 i40e_aq_rem_cloud_filters(struct i40e_hw *hw, u16 seid,
 			  struct i40e_aqc_cloud_filters_element_data *filters,
 			  u8 filter_count)
@@ -5962,8 +5826,8 @@
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_remove_cloud_filters *cmd =
 	(struct i40e_aqc_add_remove_cloud_filters *)&desc.params.raw;
-	enum i40e_status_code status;
 	u16 buff_len;
+	int status;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
 					  i40e_aqc_opc_remove_cloud_filters);
@@ -5991,7 +5855,7 @@
  * function.
  *
  **/
-enum i40e_status_code
+int
 i40e_aq_rem_cloud_filters_bb(struct i40e_hw *hw, u16 seid,
 			     struct i40e_aqc_cloud_filters_element_bb *filters,
 			     u8 filter_count)
@@ -5999,8 +5863,8 @@
 	struct i40e_aq_desc desc;
 	struct i40e_aqc_add_remove_cloud_filters *cmd =
 	(struct i40e_aqc_add_remove_cloud_filters *)&desc.params.raw;
-	i40e_status status;
 	u16 buff_len;
+	int status;
 	int i;
 
 	i40e_fill_default_direct_cmd_desc(&desc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_dcb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_dcb.c
@@ -12,7 +12,7 @@
  *
  * Get the DCBX status from the Firmware
  **/
-i40e_status i40e_get_dcbx_status(struct i40e_hw *hw, u16 *status)
+int i40e_get_dcbx_status(struct i40e_hw *hw, u16 *status)
 {
 	u32 reg;
 
@@ -497,15 +497,15 @@
  *
  * Parse DCB configuration from the LLDPDU
  **/
-i40e_status i40e_lldp_to_dcb_config(u8 *lldpmib,
-				    struct i40e_dcbx_config *dcbcfg)
+int i40e_lldp_to_dcb_config(u8 *lldpmib,
+			    struct i40e_dcbx_config *dcbcfg)
 {
-	i40e_status ret = 0;
 	struct i40e_lldp_org_tlv *tlv;
-	u16 type;
-	u16 length;
 	u16 typelength;
 	u16 offset = 0;
+	int ret = 0;
+	u16 length;
+	u16 type;
 
 	if (!lldpmib || !dcbcfg)
 		return I40E_ERR_PARAM;
@@ -551,12 +551,12 @@
  *
  * Query DCB configuration from the Firmware
  **/
-i40e_status i40e_aq_get_dcb_config(struct i40e_hw *hw, u8 mib_type,
-				   u8 bridgetype,
-				   struct i40e_dcbx_config *dcbcfg)
+int i40e_aq_get_dcb_config(struct i40e_hw *hw, u8 mib_type,
+			   u8 bridgetype,
+			   struct i40e_dcbx_config *dcbcfg)
 {
-	i40e_status ret = 0;
 	struct i40e_virt_mem mem;
+	int ret = 0;
 	u8 *lldpmib;
 
 	/* Allocate the LLDPDU */
@@ -767,9 +767,9 @@
  *
  * Get IEEE mode DCB configuration from the Firmware
  **/
-static i40e_status i40e_get_ieee_dcb_config(struct i40e_hw *hw)
+static int i40e_get_ieee_dcb_config(struct i40e_hw *hw)
 {
-	i40e_status ret = 0;
+	int ret = 0;
 
 	/* IEEE mode */
 	hw->local_dcbx_config.dcbx_mode = I40E_DCBX_MODE_IEEE;
@@ -797,11 +797,11 @@
  *
  * Get DCB configuration from the Firmware
  **/
-i40e_status i40e_get_dcb_config(struct i40e_hw *hw)
+int i40e_get_dcb_config(struct i40e_hw *hw)
 {
-	i40e_status ret = 0;
-	struct i40e_aqc_get_cee_dcb_cfg_resp cee_cfg;
 	struct i40e_aqc_get_cee_dcb_cfg_v1_resp cee_v1_cfg;
+	struct i40e_aqc_get_cee_dcb_cfg_resp cee_cfg;
+	int ret = 0;
 
 	/* If Firmware version < v4.33 on X710/XL710, IEEE only */
 	if ((hw->mac.type == I40E_MAC_XL710) &&
@@ -867,11 +867,11 @@
  *
  * Update DCB configuration from the Firmware
  **/
-i40e_status i40e_init_dcb(struct i40e_hw *hw, bool enable_mib_change)
+int i40e_init_dcb(struct i40e_hw *hw, bool enable_mib_change)
 {
-	i40e_status ret = 0;
 	struct i40e_lldp_variables lldp_cfg;
 	u8 adminstatus = 0;
+	int ret = 0;
 
 	if (!hw->func_caps.dcb)
 		return I40E_NOT_SUPPORTED;
@@ -940,13 +940,13 @@
  * Get status of FW Link Layer Discovery Protocol (LLDP) Agent.
  * Status of agent is reported via @lldp_status parameter.
  **/
-enum i40e_status_code
+int
 i40e_get_fw_lldp_status(struct i40e_hw *hw,
 			enum i40e_get_fw_lldp_status_resp *lldp_status)
 {
 	struct i40e_virt_mem mem;
-	i40e_status ret;
 	u8 *lldpmib;
+	int ret;
 
 	if (!lldp_status)
 		return I40E_ERR_PARAM;
@@ -1238,13 +1238,13 @@
  *
  * Set DCB configuration to the Firmware
  **/
-i40e_status i40e_set_dcb_config(struct i40e_hw *hw)
+int i40e_set_dcb_config(struct i40e_hw *hw)
 {
 	struct i40e_dcbx_config *dcbcfg;
 	struct i40e_virt_mem mem;
 	u8 mib_type, *lldpmib;
-	i40e_status ret;
 	u16 miblen;
+	int ret;
 
 	/* update the hw local config */
 	dcbcfg = &hw->local_dcbx_config;
@@ -1274,8 +1274,8 @@
  *
  * send DCB configuration to FW
  **/
-i40e_status i40e_dcb_config_to_lldp(u8 *lldpmib, u16 *miblen,
-				    struct i40e_dcbx_config *dcbcfg)
+int i40e_dcb_config_to_lldp(u8 *lldpmib, u16 *miblen,
+			    struct i40e_dcbx_config *dcbcfg)
 {
 	u16 length, offset = 0, tlvid, typelength;
 	struct i40e_lldp_org_tlv *tlv;
@@ -1888,13 +1888,13 @@
  *
  * Reads the LLDP configuration data from NVM using passed addresses
  **/
-static i40e_status _i40e_read_lldp_cfg(struct i40e_hw *hw,
-				       struct i40e_lldp_variables *lldp_cfg,
-				       u8 module, u32 word_offset)
+static int _i40e_read_lldp_cfg(struct i40e_hw *hw,
+			       struct i40e_lldp_variables *lldp_cfg,
+			       u8 module, u32 word_offset)
 {
 	u32 address, offset = (2 * word_offset);
-	i40e_status ret;
 	__le16 raw_mem;
+	int ret;
 	u16 mem;
 
 	ret = i40e_acquire_nvm(hw, I40E_RESOURCE_READ);
@@ -1950,10 +1950,10 @@
  *
  * Reads the LLDP configuration data from NVM
  **/
-i40e_status i40e_read_lldp_cfg(struct i40e_hw *hw,
-			       struct i40e_lldp_variables *lldp_cfg)
+int i40e_read_lldp_cfg(struct i40e_hw *hw,
+		       struct i40e_lldp_variables *lldp_cfg)
 {
-	i40e_status ret = 0;
+	int ret = 0;
 	u32 mem;
 
 	if (!lldp_cfg)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_dcb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_dcb.h
@@ -264,20 +264,20 @@
 void i40e_dcb_hw_rx_pb_config(struct i40e_hw *hw,
 			      struct i40e_rx_pb_config *old_pb_cfg,
 			      struct i40e_rx_pb_config *new_pb_cfg);
-i40e_status i40e_get_dcbx_status(struct i40e_hw *hw,
-				 u16 *status);
-i40e_status i40e_lldp_to_dcb_config(u8 *lldpmib,
-				    struct i40e_dcbx_config *dcbcfg);
-i40e_status i40e_aq_get_dcb_config(struct i40e_hw *hw, u8 mib_type,
-				   u8 bridgetype,
-				   struct i40e_dcbx_config *dcbcfg);
-i40e_status i40e_get_dcb_config(struct i40e_hw *hw);
-i40e_status i40e_init_dcb(struct i40e_hw *hw,
-			  bool enable_mib_change);
-enum i40e_status_code
+int i40e_get_dcbx_status(struct i40e_hw *hw,
+			 u16 *status);
+int i40e_lldp_to_dcb_config(u8 *lldpmib,
+			    struct i40e_dcbx_config *dcbcfg);
+int i40e_aq_get_dcb_config(struct i40e_hw *hw, u8 mib_type,
+			   u8 bridgetype,
+			   struct i40e_dcbx_config *dcbcfg);
+int i40e_get_dcb_config(struct i40e_hw *hw);
+int i40e_init_dcb(struct i40e_hw *hw,
+		  bool enable_mib_change);
+int
 i40e_get_fw_lldp_status(struct i40e_hw *hw,
 			enum i40e_get_fw_lldp_status_resp *lldp_status);
-i40e_status i40e_set_dcb_config(struct i40e_hw *hw);
-i40e_status i40e_dcb_config_to_lldp(u8 *lldpmib, u16 *miblen,
-				    struct i40e_dcbx_config *dcbcfg);
+int i40e_set_dcb_config(struct i40e_hw *hw);
+int i40e_dcb_config_to_lldp(u8 *lldpmib, u16 *miblen,
+			    struct i40e_dcbx_config *dcbcfg);
 #endif /* _I40E_DCB_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_dcb_nl.c
@@ -135,8 +135,8 @@
 	ret = i40e_hw_dcb_config(pf, &pf->tmp_cfg);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Failed setting DCB ETS configuration err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Failed setting DCB ETS configuration err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EINVAL;
 	}
@@ -174,8 +174,8 @@
 	ret = i40e_hw_dcb_config(pf, &pf->tmp_cfg);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Failed setting DCB PFC configuration err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Failed setting DCB PFC configuration err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EINVAL;
 	}
@@ -225,8 +225,8 @@
 	ret = i40e_hw_dcb_config(pf, &pf->tmp_cfg);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Failed setting DCB configuration err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Failed setting DCB configuration err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EINVAL;
 	}
@@ -290,8 +290,8 @@
 	ret = i40e_hw_dcb_config(pf, &pf->tmp_cfg);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Failed setting DCB configuration err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Failed setting DCB configuration err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_ddp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_ddp.c
@@ -36,7 +36,7 @@
 {
 	struct i40e_ddp_profile_list *profile_list;
 	u8 buff[I40E_PROFILE_LIST_SIZE];
-	i40e_status status;
+	int status;
 	int i;
 
 	status = i40e_aq_get_ddp_list(hw, buff, I40E_PROFILE_LIST_SIZE, 0,
@@ -91,7 +91,7 @@
 {
 	struct i40e_ddp_profile_list *profile_list;
 	u8 buff[I40E_PROFILE_LIST_SIZE];
-	i40e_status status;
+	int status;
 	int i;
 
 	status = i40e_aq_get_ddp_list(hw, buff, I40E_PROFILE_LIST_SIZE, 0,
@@ -117,14 +117,14 @@
  *
  * Register a profile to the list of loaded profiles.
  */
-static enum i40e_status_code
+static int
 i40e_add_pinfo(struct i40e_hw *hw, struct i40e_profile_segment *profile,
 	       u8 *profile_info_sec, u32 track_id)
 {
 	struct i40e_profile_section_header *sec;
 	struct i40e_profile_info *pinfo;
-	i40e_status status;
 	u32 offset = 0, info = 0;
+	int status;
 
 	sec = (struct i40e_profile_section_header *)profile_info_sec;
 	sec->tbl_size = 1;
@@ -157,14 +157,14 @@
  *
  * Removes DDP profile from the NIC.
  **/
-static enum i40e_status_code
+static int
 i40e_del_pinfo(struct i40e_hw *hw, struct i40e_profile_segment *profile,
 	       u8 *profile_info_sec, u32 track_id)
 {
 	struct i40e_profile_section_header *sec;
 	struct i40e_profile_info *pinfo;
-	i40e_status status;
 	u32 offset = 0, info = 0;
+	int status;
 
 	sec = (struct i40e_profile_section_header *)profile_info_sec;
 	sec->tbl_size = 1;
@@ -270,12 +270,12 @@
 	struct i40e_profile_segment *profile_hdr;
 	struct i40e_profile_info pinfo;
 	struct i40e_package_header *pkg_hdr;
-	i40e_status status;
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_vsi *vsi = np->vsi;
 	struct i40e_pf *pf = vsi->back;
 	u32 track_id;
 	int istatus;
+	int status;
 
 	pkg_hdr = (struct i40e_package_header *)data;
 	if (!i40e_ddp_is_pkg_hdr_valid(netdev, pkg_hdr, size))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_debugfs.c
@@ -105,6 +105,7 @@
 	"ACTIVE",
 	"FAILED",
 	"REMOVE",
+	"NEW_SYNC",
 };
 
 /**
@@ -240,7 +241,7 @@
 		 (unsigned long int)vsi->net_stats_offsets.rx_compressed,
 		 (unsigned long int)vsi->net_stats_offsets.tx_compressed);
 	dev_info(&pf->pdev->dev,
-		 "    tx_restart = %d, tx_busy = %d, rx_buf_failed = %d, rx_page_failed = %d\n",
+		 "    tx_restart = %llu, tx_busy = %llu, rx_buf_failed = %llu, rx_page_failed = %llu\n",
 		 vsi->tx_restart, vsi->tx_busy,
 		 vsi->rx_buf_failed, vsi->rx_page_failed);
 	rcu_read_lock();
@@ -553,6 +554,14 @@
 		dev_info(&pf->pdev->dev, "vsi %d not found\n", vsi_seid);
 		return;
 	}
+	if (vsi->type != I40E_VSI_MAIN &&
+	    vsi->type != I40E_VSI_FDIR &&
+	    vsi->type != I40E_VSI_VMDQ2) {
+		dev_info(&pf->pdev->dev,
+			 "vsi %d type %d descriptor rings not available\n",
+			 vsi_seid, vsi->type);
+		return;
+	}
 	if (type == RING_TYPE_XDP && !i40e_enabled_xdp_vsi(vsi)) {
 		dev_info(&pf->pdev->dev, "XDP not enabled on VSI %d\n", vsi_seid);
 		return;
@@ -734,10 +743,8 @@
 		vsi = pf->vsi[vf->lan_vsi_idx];
 		dev_info(&pf->pdev->dev, "vf %2d: VSI id=%d, seid=%d, qps=%d\n",
 			 vf_id, vf->lan_vsi_id, vsi->seid, vf->num_queue_pairs);
-		dev_info(&pf->pdev->dev, "       num MDD=%lld, invalid msg=%lld, valid msg=%lld\n",
-			 vf->num_mdd_events,
-			 vf->num_invalid_msgs,
-			 vf->num_valid_msgs);
+		dev_info(&pf->pdev->dev, "       num MDD=%lld\n",
+			 vf->num_mdd_events);
 	} else {
 		dev_info(&pf->pdev->dev, "invalid VF id %d\n", vf_id);
 	}
@@ -912,9 +919,9 @@
 		dev_info(&pf->pdev->dev, "deleting relay %d\n", veb_seid);
 		i40e_veb_release(pf->veb[i]);
 	} else if (strncmp(cmd_buf, "add pvid", 8) == 0) {
-		i40e_status ret;
-		u16 vid;
 		unsigned int v;
+		int ret;
+		u16 vid;
 
 		cnt = sscanf(&cmd_buf[8], "%i %u", &vsi_seid, &v);
 		if (cnt != 2) {
@@ -1278,7 +1285,7 @@
 		}
 	} else if (strncmp(cmd_buf, "send aq_cmd", 11) == 0) {
 		struct i40e_aq_desc *desc;
-		i40e_status ret;
+		int ret;
 
 		desc = kzalloc(sizeof(struct i40e_aq_desc), GFP_KERNEL);
 		if (!desc)
@@ -1324,9 +1331,9 @@
 		desc = NULL;
 	} else if (strncmp(cmd_buf, "send indirect aq_cmd", 20) == 0) {
 		struct i40e_aq_desc *desc;
-		i40e_status ret;
 		u16 buffer_len;
 		u8 *buff;
+		int ret;
 
 		desc = kzalloc(sizeof(struct i40e_aq_desc), GFP_KERNEL);
 		if (!desc)
@@ -1833,7 +1840,7 @@
 void i40e_dbg_init(void)
 {
 	i40e_dbg_root = debugfs_create_dir(i40e_driver_name, NULL);
-	if (!i40e_dbg_root)
+	if (IS_ERR(i40e_dbg_root))
 		pr_info("init of debugfs failed\n");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_diag.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_diag.c
@@ -10,8 +10,8 @@
  * @reg: reg to be tested
  * @mask: bits to be touched
  **/
-static i40e_status i40e_diag_reg_pattern_test(struct i40e_hw *hw,
-							u32 reg, u32 mask)
+static int i40e_diag_reg_pattern_test(struct i40e_hw *hw,
+				      u32 reg, u32 mask)
 {
 	static const u32 patterns[] = {
 		0x5A5A5A5A, 0xA5A5A5A5, 0x00000000, 0xFFFFFFFF
@@ -44,7 +44,7 @@
 	return 0;
 }
 
-struct i40e_diag_reg_test_info i40e_reg_list[] = {
+const struct i40e_diag_reg_test_info i40e_reg_list[] = {
 	/* offset               mask         elements   stride */
 	{I40E_QTX_CTL(0),       0x0000FFBF, 1,
 		I40E_QTX_CTL(1) - I40E_QTX_CTL(0)},
@@ -74,31 +74,32 @@
  *
  * Perform registers diagnostic test
  **/
-i40e_status i40e_diag_reg_test(struct i40e_hw *hw)
+int i40e_diag_reg_test(struct i40e_hw *hw)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 	u32 reg, mask;
+	u32 elements;
 	u32 i, j;
 
 	for (i = 0; i40e_reg_list[i].offset != 0 &&
 					     !ret_code; i++) {
 
+		elements = i40e_reg_list[i].elements;
 		/* set actual reg range for dynamically allocated resources */
 		if (i40e_reg_list[i].offset == I40E_QTX_CTL(0) &&
 		    hw->func_caps.num_tx_qp != 0)
-			i40e_reg_list[i].elements = hw->func_caps.num_tx_qp;
+			elements = hw->func_caps.num_tx_qp;
 		if ((i40e_reg_list[i].offset == I40E_PFINT_ITRN(0, 0) ||
 		     i40e_reg_list[i].offset == I40E_PFINT_ITRN(1, 0) ||
 		     i40e_reg_list[i].offset == I40E_PFINT_ITRN(2, 0) ||
 		     i40e_reg_list[i].offset == I40E_QINT_TQCTL(0) ||
 		     i40e_reg_list[i].offset == I40E_QINT_RQCTL(0)) &&
 		    hw->func_caps.num_msix_vectors != 0)
-			i40e_reg_list[i].elements =
-				hw->func_caps.num_msix_vectors - 1;
+			elements = hw->func_caps.num_msix_vectors - 1;
 
 		/* test register access */
 		mask = i40e_reg_list[i].mask;
-		for (j = 0; j < i40e_reg_list[i].elements && !ret_code; j++) {
+		for (j = 0; j < elements && !ret_code; j++) {
 			reg = i40e_reg_list[i].offset +
 			      (j * i40e_reg_list[i].stride);
 			ret_code = i40e_diag_reg_pattern_test(hw, reg, mask);
@@ -114,9 +115,9 @@
  *
  * Perform EEPROM diagnostic test
  **/
-i40e_status i40e_diag_eeprom_test(struct i40e_hw *hw)
+int i40e_diag_eeprom_test(struct i40e_hw *hw)
 {
-	i40e_status ret_code;
+	int ret_code;
 	u16 reg_val;
 
 	/* read NVM control word and if NVM valid, validate EEPROM checksum*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_diag.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_diag.h
@@ -20,9 +20,9 @@
 	u32 stride;	/* bytes between each element */
 };
 
-extern struct i40e_diag_reg_test_info i40e_reg_list[];
+extern const struct i40e_diag_reg_test_info i40e_reg_list[];
 
-i40e_status i40e_diag_reg_test(struct i40e_hw *hw);
-i40e_status i40e_diag_eeprom_test(struct i40e_hw *hw);
+int i40e_diag_reg_test(struct i40e_hw *hw);
+int i40e_diag_eeprom_test(struct i40e_hw *hw);
 
 #endif /* _I40E_DIAG_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -451,6 +451,8 @@
 	I40E_PRIV_FLAG("disable-fw-lldp", I40E_FLAG_DISABLE_FW_LLDP, 0),
 	I40E_PRIV_FLAG("rs-fec", I40E_FLAG_RS_FEC, 0),
 	I40E_PRIV_FLAG("base-r-fec", I40E_FLAG_BASE_R_FEC, 0),
+	I40E_PRIV_FLAG("vf-vlan-pruning",
+		       I40E_FLAG_VF_VLAN_PRUNING, 0),
 };
 
 #define I40E_PRIV_FLAGS_STR_LEN ARRAY_SIZE(i40e_gstrings_priv_flags)
@@ -1154,8 +1156,8 @@
 	struct i40e_vsi *vsi = np->vsi;
 	struct i40e_hw *hw = &pf->hw;
 	bool autoneg_changed = false;
-	i40e_status status = 0;
 	int timeout = 50;
+	int status = 0;
 	int err = 0;
 	u8 autoneg;
 
@@ -1357,8 +1359,8 @@
 		status = i40e_aq_set_phy_config(hw, &config, NULL);
 		if (status) {
 			netdev_info(netdev,
-				    "Set phy config failed, err %s aq_err %s\n",
-				    i40e_stat_str(hw, status),
+				    "Set phy config failed, err %d aq_err %s\n",
+				    status,
 				    i40e_aq_str(hw, hw->aq.asq_last_status));
 			err = -EAGAIN;
 			goto done;
@@ -1367,8 +1369,8 @@
 		status = i40e_update_link_info(hw);
 		if (status)
 			netdev_dbg(netdev,
-				   "Updating link info failed with err %s aq_err %s\n",
-				   i40e_stat_str(hw, status),
+				   "Updating link info failed with err %d aq_err %s\n",
+				   status,
 				   i40e_aq_str(hw, hw->aq.asq_last_status));
 
 	} else {
@@ -1387,7 +1389,7 @@
 	struct i40e_aq_get_phy_abilities_resp abilities;
 	struct i40e_pf *pf = np->vsi->back;
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status status = 0;
+	int status = 0;
 	u32 flags = 0;
 	int err = 0;
 
@@ -1419,8 +1421,8 @@
 		status = i40e_aq_set_phy_config(hw, &config, NULL);
 		if (status) {
 			netdev_info(netdev,
-				    "Set phy config failed, err %s aq_err %s\n",
-				    i40e_stat_str(hw, status),
+				    "Set phy config failed, err %d aq_err %s\n",
+				    status,
 				    i40e_aq_str(hw, hw->aq.asq_last_status));
 			err = -EAGAIN;
 			goto done;
@@ -1433,8 +1435,8 @@
 			 * (e.g. no physical connection etc.)
 			 */
 			netdev_dbg(netdev,
-				   "Updating link info failed with err %s aq_err %s\n",
-				   i40e_stat_str(hw, status),
+				   "Updating link info failed with err %d aq_err %s\n",
+				   status,
 				   i40e_aq_str(hw, hw->aq.asq_last_status));
 	}
 
@@ -1449,7 +1451,7 @@
 	struct i40e_aq_get_phy_abilities_resp abilities;
 	struct i40e_pf *pf = np->vsi->back;
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status status = 0;
+	int status = 0;
 	int err = 0;
 	u8 fec_cfg;
 
@@ -1536,12 +1538,12 @@
 	struct i40e_pf *pf = np->vsi->back;
 	struct i40e_hw *hw = &pf->hw;
 	bool link_up = hw->phy.link_info.link_info & I40E_AQ_LINK_UP;
-	i40e_status ret = 0;
+	int ret = 0;
 
 	ret = i40e_aq_set_link_restart_an(hw, link_up, NULL);
 	if (ret) {
-		netdev_info(netdev, "link restart failed, err %s aq_err %s\n",
-			    i40e_stat_str(hw, ret),
+		netdev_info(netdev, "link restart failed, err %d aq_err %s\n",
+			    ret,
 			    i40e_aq_str(hw, hw->aq.asq_last_status));
 		return -EIO;
 	}
@@ -1601,9 +1603,9 @@
 	struct i40e_link_status *hw_link_info = &hw->phy.link_info;
 	struct i40e_dcbx_config *dcbx_cfg = &hw->local_dcbx_config;
 	bool link_up = hw_link_info->link_info & I40E_AQ_LINK_UP;
-	i40e_status status;
 	u8 aq_failures;
 	int err = 0;
+	int status;
 	u32 is_an;
 
 	/* Changing the port's flow control is not supported if this isn't the
@@ -1657,20 +1659,20 @@
 	status = i40e_set_fc(hw, &aq_failures, link_up);
 
 	if (aq_failures & I40E_SET_FC_AQ_FAIL_GET) {
-		netdev_info(netdev, "Set fc failed on the get_phy_capabilities call with err %s aq_err %s\n",
-			    i40e_stat_str(hw, status),
+		netdev_info(netdev, "Set fc failed on the get_phy_capabilities call with err %d aq_err %s\n",
+			    status,
 			    i40e_aq_str(hw, hw->aq.asq_last_status));
 		err = -EAGAIN;
 	}
 	if (aq_failures & I40E_SET_FC_AQ_FAIL_SET) {
-		netdev_info(netdev, "Set fc failed on the set_phy_config call with err %s aq_err %s\n",
-			    i40e_stat_str(hw, status),
+		netdev_info(netdev, "Set fc failed on the set_phy_config call with err %d aq_err %s\n",
+			    status,
 			    i40e_aq_str(hw, hw->aq.asq_last_status));
 		err = -EAGAIN;
 	}
 	if (aq_failures & I40E_SET_FC_AQ_FAIL_UPDATE) {
-		netdev_info(netdev, "Set fc failed on the get_link_info call with err %s aq_err %s\n",
-			    i40e_stat_str(hw, status),
+		netdev_info(netdev, "Set fc failed on the get_link_info call with err %d aq_err %s\n",
+			    status,
 			    i40e_aq_str(hw, hw->aq.asq_last_status));
 		err = -EAGAIN;
 	}
@@ -2083,9 +2085,6 @@
 			err = i40e_setup_rx_descriptors(&rx_rings[i]);
 			if (err)
 				goto rx_unwind;
-			err = i40e_alloc_rx_bi(&rx_rings[i]);
-			if (err)
-				goto rx_unwind;
 
 			/* now allocate the Rx buffers to make sure the OS
 			 * has enough memory, any failure here means abort
@@ -2484,8 +2483,8 @@
 {
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_pf *pf = np->vsi->back;
-	i40e_status status;
 	bool link_up = false;
+	int status;
 
 	netif_info(pf, hw, netdev, "link test\n");
 	status = i40e_get_link_status(&pf->hw, &link_up);
@@ -2576,15 +2575,16 @@
 
 		set_bit(__I40E_TESTING, pf->state);
 
+		if (test_bit(__I40E_RESET_RECOVERY_PENDING, pf->state) ||
+		    test_bit(__I40E_RESET_INTR_RECEIVED, pf->state)) {
+			dev_warn(&pf->pdev->dev,
+				 "Cannot start offline testing when PF is in reset state.\n");
+			goto skip_ol_tests;
+		}
+
 		if (i40e_active_vfs(pf) || i40e_active_vmdqs(pf)) {
 			dev_warn(&pf->pdev->dev,
 				 "Please take active VFs and Netqueues offline and restart the adapter before running NIC diagnostics\n");
-			data[I40E_ETH_TEST_REG]		= 1;
-			data[I40E_ETH_TEST_EEPROM]	= 1;
-			data[I40E_ETH_TEST_INTR]	= 1;
-			data[I40E_ETH_TEST_LINK]	= 1;
-			eth_test->flags |= ETH_TEST_FL_FAILED;
-			clear_bit(__I40E_TESTING, pf->state);
 			goto skip_ol_tests;
 		}
 
@@ -2631,9 +2631,17 @@
 		data[I40E_ETH_TEST_INTR] = 0;
 	}
 
-skip_ol_tests:
-
 	netif_info(pf, drv, netdev, "testing finished\n");
+	return;
+
+skip_ol_tests:
+	data[I40E_ETH_TEST_REG]		= 1;
+	data[I40E_ETH_TEST_EEPROM]	= 1;
+	data[I40E_ETH_TEST_INTR]	= 1;
+	data[I40E_ETH_TEST_LINK]	= 1;
+	eth_test->flags |= ETH_TEST_FL_FAILED;
+	clear_bit(__I40E_TESTING, pf->state);
+	netif_info(pf, drv, netdev, "testing failed\n");
 }
 
 static void i40e_get_wol(struct net_device *netdev,
@@ -2699,11 +2707,11 @@
 			    enum ethtool_phys_id_state state)
 {
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
-	i40e_status ret = 0;
 	struct i40e_pf *pf = np->vsi->back;
 	struct i40e_hw *hw = &pf->hw;
 	int blink_freq = 2;
 	u16 temp_status;
+	int ret = 0;
 
 	switch (state) {
 	case ETHTOOL_ID_ACTIVE:
@@ -3079,10 +3087,17 @@
 
 		if (cmd->flow_type == TCP_V4_FLOW ||
 		    cmd->flow_type == UDP_V4_FLOW) {
-			if (i_set & I40E_L3_SRC_MASK)
-				cmd->data |= RXH_IP_SRC;
-			if (i_set & I40E_L3_DST_MASK)
-				cmd->data |= RXH_IP_DST;
+			if (hw->mac.type == I40E_MAC_X722) {
+				if (i_set & I40E_X722_L3_SRC_MASK)
+					cmd->data |= RXH_IP_SRC;
+				if (i_set & I40E_X722_L3_DST_MASK)
+					cmd->data |= RXH_IP_DST;
+			} else {
+				if (i_set & I40E_L3_SRC_MASK)
+					cmd->data |= RXH_IP_SRC;
+				if (i_set & I40E_L3_DST_MASK)
+					cmd->data |= RXH_IP_DST;
+			}
 		} else if (cmd->flow_type == TCP_V6_FLOW ||
 			  cmd->flow_type == UDP_V6_FLOW) {
 			if (i_set & I40E_L3_V6_SRC_MASK)
@@ -3440,12 +3455,15 @@
 
 /**
  * i40e_get_rss_hash_bits - Read RSS Hash bits from register
+ * @hw: hw structure
  * @nfc: pointer to user request
  * @i_setc: bits currently set
  *
  * Returns value of bits to be set per user request
  **/
-static u64 i40e_get_rss_hash_bits(struct ethtool_rxnfc *nfc, u64 i_setc)
+static u64 i40e_get_rss_hash_bits(struct i40e_hw *hw,
+				  struct ethtool_rxnfc *nfc,
+				  u64 i_setc)
 {
 	u64 i_set = i_setc;
 	u64 src_l3 = 0, dst_l3 = 0;
@@ -3464,8 +3482,13 @@
 		dst_l3 = I40E_L3_V6_DST_MASK;
 	} else if (nfc->flow_type == TCP_V4_FLOW ||
 		  nfc->flow_type == UDP_V4_FLOW) {
-		src_l3 = I40E_L3_SRC_MASK;
-		dst_l3 = I40E_L3_DST_MASK;
+		if (hw->mac.type == I40E_MAC_X722) {
+			src_l3 = I40E_X722_L3_SRC_MASK;
+			dst_l3 = I40E_X722_L3_DST_MASK;
+		} else {
+			src_l3 = I40E_L3_SRC_MASK;
+			dst_l3 = I40E_L3_DST_MASK;
+		}
 	} else {
 		/* Any other flow type are not supported here */
 		return i_set;
@@ -3483,6 +3506,7 @@
 	return i_set;
 }
 
+#define FLOW_PCTYPES_SIZE 64
 /**
  * i40e_set_rss_hash_opt - Enable/Disable flow types for RSS hash
  * @pf: pointer to the physical function struct
@@ -3495,9 +3519,11 @@
 	struct i40e_hw *hw = &pf->hw;
 	u64 hena = (u64)i40e_read_rx_ctl(hw, I40E_PFQF_HENA(0)) |
 		   ((u64)i40e_read_rx_ctl(hw, I40E_PFQF_HENA(1)) << 32);
-	u8 flow_pctype = 0;
+	DECLARE_BITMAP(flow_pctypes, FLOW_PCTYPES_SIZE);
 	u64 i_set, i_setc;
 
+	bitmap_zero(flow_pctypes, FLOW_PCTYPES_SIZE);
+
 	if (pf->flags & I40E_FLAG_MFP_ENABLED) {
 		dev_err(&pf->pdev->dev,
 			"Change of RSS hash input set is not supported when MFP mode is enabled\n");
@@ -3513,36 +3539,35 @@
 
 	switch (nfc->flow_type) {
 	case TCP_V4_FLOW:
-		flow_pctype = I40E_FILTER_PCTYPE_NONF_IPV4_TCP;
+		set_bit(I40E_FILTER_PCTYPE_NONF_IPV4_TCP, flow_pctypes);
 		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE)
-			hena |=
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_IPV4_TCP_SYN_NO_ACK);
+			set_bit(I40E_FILTER_PCTYPE_NONF_IPV4_TCP_SYN_NO_ACK,
+				flow_pctypes);
 		break;
 	case TCP_V6_FLOW:
-		flow_pctype = I40E_FILTER_PCTYPE_NONF_IPV6_TCP;
-		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE)
-			hena |=
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_IPV4_TCP_SYN_NO_ACK);
+		set_bit(I40E_FILTER_PCTYPE_NONF_IPV6_TCP, flow_pctypes);
 		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE)
-			hena |=
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_IPV6_TCP_SYN_NO_ACK);
+			set_bit(I40E_FILTER_PCTYPE_NONF_IPV6_TCP_SYN_NO_ACK,
+				flow_pctypes);
 		break;
 	case UDP_V4_FLOW:
-		flow_pctype = I40E_FILTER_PCTYPE_NONF_IPV4_UDP;
-		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE)
-			hena |=
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_UNICAST_IPV4_UDP) |
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_MULTICAST_IPV4_UDP);
-
+		set_bit(I40E_FILTER_PCTYPE_NONF_IPV4_UDP, flow_pctypes);
+		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE) {
+			set_bit(I40E_FILTER_PCTYPE_NONF_UNICAST_IPV4_UDP,
+				flow_pctypes);
+			set_bit(I40E_FILTER_PCTYPE_NONF_MULTICAST_IPV4_UDP,
+				flow_pctypes);
+		}
 		hena |= BIT_ULL(I40E_FILTER_PCTYPE_FRAG_IPV4);
 		break;
 	case UDP_V6_FLOW:
-		flow_pctype = I40E_FILTER_PCTYPE_NONF_IPV6_UDP;
-		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE)
-			hena |=
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_UNICAST_IPV6_UDP) |
-			  BIT_ULL(I40E_FILTER_PCTYPE_NONF_MULTICAST_IPV6_UDP);
-
+		set_bit(I40E_FILTER_PCTYPE_NONF_IPV6_UDP, flow_pctypes);
+		if (pf->hw_features & I40E_HW_MULTIPLE_TCP_UDP_RSS_PCTYPE) {
+			set_bit(I40E_FILTER_PCTYPE_NONF_UNICAST_IPV6_UDP,
+				flow_pctypes);
+			set_bit(I40E_FILTER_PCTYPE_NONF_MULTICAST_IPV6_UDP,
+				flow_pctypes);
+		}
 		hena |= BIT_ULL(I40E_FILTER_PCTYPE_FRAG_IPV6);
 		break;
 	case AH_ESP_V4_FLOW:
@@ -3575,17 +3600,20 @@
 		return -EINVAL;
 	}
 
-	if (flow_pctype) {
-		i_setc = (u64)i40e_read_rx_ctl(hw, I40E_GLQF_HASH_INSET(0,
-					       flow_pctype)) |
-			((u64)i40e_read_rx_ctl(hw, I40E_GLQF_HASH_INSET(1,
-					       flow_pctype)) << 32);
-		i_set = i40e_get_rss_hash_bits(nfc, i_setc);
-		i40e_write_rx_ctl(hw, I40E_GLQF_HASH_INSET(0, flow_pctype),
-				  (u32)i_set);
-		i40e_write_rx_ctl(hw, I40E_GLQF_HASH_INSET(1, flow_pctype),
-				  (u32)(i_set >> 32));
-		hena |= BIT_ULL(flow_pctype);
+	if (bitmap_weight(flow_pctypes, FLOW_PCTYPES_SIZE)) {
+		u8 flow_id;
+
+		for_each_set_bit(flow_id, flow_pctypes, FLOW_PCTYPES_SIZE) {
+			i_setc = (u64)i40e_read_rx_ctl(hw, I40E_GLQF_HASH_INSET(0, flow_id)) |
+				 ((u64)i40e_read_rx_ctl(hw, I40E_GLQF_HASH_INSET(1, flow_id)) << 32);
+			i_set = i40e_get_rss_hash_bits(&pf->hw, nfc, i_setc);
+
+			i40e_write_rx_ctl(hw, I40E_GLQF_HASH_INSET(0, flow_id),
+					  (u32)i_set);
+			i40e_write_rx_ctl(hw, I40E_GLQF_HASH_INSET(1, flow_id),
+					  (u32)(i_set >> 32));
+			hena |= BIT_ULL(flow_id);
+		}
 	}
 
 	i40e_write_rx_ctl(hw, I40E_PFQF_HENA(0), (u32)hena);
@@ -4338,11 +4366,7 @@
 			return -EOPNOTSUPP;
 
 		/* First 4 bytes of L4 header */
-		if (usr_ip4_spec->l4_4_bytes == htonl(0xFFFFFFFF))
-			new_mask |= I40E_L4_SRC_MASK | I40E_L4_DST_MASK;
-		else if (!usr_ip4_spec->l4_4_bytes)
-			new_mask &= ~(I40E_L4_SRC_MASK | I40E_L4_DST_MASK);
-		else
+		if (usr_ip4_spec->l4_4_bytes)
 			return -EOPNOTSUPP;
 
 		/* Filtering on Type of Service is not supported. */
@@ -4376,16 +4400,12 @@
 				    (struct in6_addr *)&ipv6_full_mask))
 			new_mask |= I40E_L3_V6_DST_MASK;
 		else if (ipv6_addr_any((struct in6_addr *)
-				       &usr_ip6_spec->ip6src))
+				       &usr_ip6_spec->ip6dst))
 			new_mask &= ~I40E_L3_V6_DST_MASK;
 		else
 			return -EOPNOTSUPP;
 
-		if (usr_ip6_spec->l4_4_bytes == htonl(0xFFFFFFFF))
-			new_mask |= I40E_L4_SRC_MASK | I40E_L4_DST_MASK;
-		else if (!usr_ip6_spec->l4_4_bytes)
-			new_mask &= ~(I40E_L4_SRC_MASK | I40E_L4_DST_MASK);
-		else
+		if (usr_ip6_spec->l4_4_bytes)
 			return -EOPNOTSUPP;
 
 		/* Filtering on Traffic class is not supported. */
@@ -4912,7 +4932,7 @@
 	/* We do not support setting channels via ethtool when TCs are
 	 * configured through mqprio
 	 */
-	if (pf->flags & I40E_FLAG_TC_MQPRIO)
+	if (i40e_is_tc_mqprio_enabled(pf))
 		return -EINVAL;
 
 	/* verify they are not requesting separate vectors */
@@ -5127,7 +5147,7 @@
 	struct i40e_vsi *vsi = np->vsi;
 	struct i40e_pf *pf = vsi->back;
 	u32 reset_needed = 0;
-	i40e_status status;
+	int status;
 	u32 i, j;
 
 	orig_flags = READ_ONCE(pf->flags);
@@ -5242,8 +5262,8 @@
 						0, NULL);
 		if (ret && pf->hw.aq.asq_last_status != I40E_AQ_RC_ESRCH) {
 			dev_info(&pf->pdev->dev,
-				 "couldn't set switch config bits, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "couldn't set switch config bits, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			/* not a fatal problem, just keep going */
@@ -5275,6 +5295,13 @@
 		return -EOPNOTSUPP;
 	}
 
+	if ((changed_flags & I40E_FLAG_VF_VLAN_PRUNING) &&
+	    pf->num_alloc_vfs) {
+		dev_warn(&pf->pdev->dev,
+			 "Changing vf-vlan-pruning flag while VF(s) are active is not supported\n");
+		return -EOPNOTSUPP;
+	}
+
 	if ((changed_flags & new_flags &
 	     I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED) &&
 	    (new_flags & I40E_FLAG_MFP_ENABLED))
@@ -5308,9 +5335,8 @@
 					return -EBUSY;
 				default:
 					dev_warn(&pf->pdev->dev,
-						 "Starting FW LLDP agent failed: error: %s, %s\n",
-						 i40e_stat_str(&pf->hw,
-							       status),
+						 "Starting FW LLDP agent failed: error: %d, %s\n",
+						 status,
 						 i40e_aq_str(&pf->hw,
 							     adq_err));
 					return -EINVAL;
@@ -5350,8 +5376,8 @@
 	u32 sff8472_comp = 0;
 	u32 sff8472_swap = 0;
 	u32 sff8636_rev = 0;
-	i40e_status status;
 	u32 type = 0;
+	int status;
 
 	/* Check if firmware supports reading module EEPROM. */
 	if (!(hw->flags & I40E_HW_FLAG_AQ_PHY_ACCESS_CAPABLE)) {
@@ -5455,8 +5481,8 @@
 	struct i40e_pf *pf = vsi->back;
 	struct i40e_hw *hw = &pf->hw;
 	bool is_sfp = false;
-	i40e_status status;
 	u32 value = 0;
+	int status;
 	int i;
 
 	if (!ee || !ee->len || !data)
@@ -5497,10 +5523,10 @@
 {
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_aq_get_phy_abilities_resp phy_cfg;
-	enum i40e_status_code status = 0;
 	struct i40e_vsi *vsi = np->vsi;
 	struct i40e_pf *pf = vsi->back;
 	struct i40e_hw *hw = &pf->hw;
+	int status = 0;
 
 	/* Get initial PHY capabilities */
 	status = i40e_aq_get_phy_capabilities(hw, false, true, &phy_cfg, NULL);
@@ -5562,11 +5588,11 @@
 {
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_aq_get_phy_abilities_resp abilities;
-	enum i40e_status_code status = I40E_SUCCESS;
 	struct i40e_aq_set_phy_config config;
 	struct i40e_vsi *vsi = np->vsi;
 	struct i40e_pf *pf = vsi->back;
 	struct i40e_hw *hw = &pf->hw;
+	int status = I40E_SUCCESS;
 	__le16 eee_capability;
 
 	/* Deny parameters we don't support */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_hmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_hmc.c
@@ -17,17 +17,17 @@
  * @type: what type of segment descriptor we're manipulating
  * @direct_mode_sz: size to alloc in direct mode
  **/
-i40e_status i40e_add_sd_table_entry(struct i40e_hw *hw,
-					      struct i40e_hmc_info *hmc_info,
-					      u32 sd_index,
-					      enum i40e_sd_entry_type type,
-					      u64 direct_mode_sz)
+int i40e_add_sd_table_entry(struct i40e_hw *hw,
+			    struct i40e_hmc_info *hmc_info,
+			    u32 sd_index,
+			    enum i40e_sd_entry_type type,
+			    u64 direct_mode_sz)
 {
 	enum i40e_memory_type mem_type __attribute__((unused));
 	struct i40e_hmc_sd_entry *sd_entry;
 	bool dma_mem_alloc_done = false;
+	int ret_code = I40E_SUCCESS;
 	struct i40e_dma_mem mem;
-	i40e_status ret_code = I40E_SUCCESS;
 	u64 alloc_len;
 
 	if (NULL == hmc_info->sd_table.sd_entry) {
@@ -106,19 +106,19 @@
  *	   aligned on 4K boundary and zeroed memory.
  *	2. It should be 4K in size.
  **/
-i40e_status i40e_add_pd_table_entry(struct i40e_hw *hw,
-					      struct i40e_hmc_info *hmc_info,
-					      u32 pd_index,
-					      struct i40e_dma_mem *rsrc_pg)
+int i40e_add_pd_table_entry(struct i40e_hw *hw,
+			    struct i40e_hmc_info *hmc_info,
+			    u32 pd_index,
+			    struct i40e_dma_mem *rsrc_pg)
 {
-	i40e_status ret_code = 0;
 	struct i40e_hmc_pd_table *pd_table;
 	struct i40e_hmc_pd_entry *pd_entry;
 	struct i40e_dma_mem mem;
 	struct i40e_dma_mem *page = &mem;
 	u32 sd_idx, rel_pd_idx;
-	u64 *pd_addr;
+	int ret_code = 0;
 	u64 page_desc;
+	u64 *pd_addr;
 
 	if (pd_index / I40E_HMC_PD_CNT_IN_SD >= hmc_info->sd_table.sd_cnt) {
 		ret_code = I40E_ERR_INVALID_PAGE_DESC_INDEX;
@@ -185,15 +185,15 @@
  *	1. Caller can deallocate the memory used by backing storage after this
  *	   function returns.
  **/
-i40e_status i40e_remove_pd_bp(struct i40e_hw *hw,
-					struct i40e_hmc_info *hmc_info,
-					u32 idx)
+int i40e_remove_pd_bp(struct i40e_hw *hw,
+		      struct i40e_hmc_info *hmc_info,
+		      u32 idx)
 {
-	i40e_status ret_code = 0;
 	struct i40e_hmc_pd_entry *pd_entry;
 	struct i40e_hmc_pd_table *pd_table;
 	struct i40e_hmc_sd_entry *sd_entry;
 	u32 sd_idx, rel_pd_idx;
+	int ret_code = 0;
 	u64 *pd_addr;
 
 	/* calculate index */
@@ -241,11 +241,11 @@
  * @hmc_info: pointer to the HMC configuration information structure
  * @idx: the page index
  **/
-i40e_status i40e_prep_remove_sd_bp(struct i40e_hmc_info *hmc_info,
-					     u32 idx)
+int i40e_prep_remove_sd_bp(struct i40e_hmc_info *hmc_info,
+			   u32 idx)
 {
-	i40e_status ret_code = 0;
 	struct i40e_hmc_sd_entry *sd_entry;
+	int ret_code = 0;
 
 	/* get the entry and decrease its ref counter */
 	sd_entry = &hmc_info->sd_table.sd_entry[idx];
@@ -269,9 +269,9 @@
  * @idx: the page index
  * @is_pf: used to distinguish between VF and PF
  **/
-i40e_status i40e_remove_sd_bp_new(struct i40e_hw *hw,
-					    struct i40e_hmc_info *hmc_info,
-					    u32 idx, bool is_pf)
+int i40e_remove_sd_bp_new(struct i40e_hw *hw,
+			  struct i40e_hmc_info *hmc_info,
+			  u32 idx, bool is_pf)
 {
 	struct i40e_hmc_sd_entry *sd_entry;
 
@@ -290,11 +290,11 @@
  * @hmc_info: pointer to the HMC configuration information structure
  * @idx: segment descriptor index to find the relevant page descriptor
  **/
-i40e_status i40e_prep_remove_pd_page(struct i40e_hmc_info *hmc_info,
-					       u32 idx)
+int i40e_prep_remove_pd_page(struct i40e_hmc_info *hmc_info,
+			     u32 idx)
 {
-	i40e_status ret_code = 0;
 	struct i40e_hmc_sd_entry *sd_entry;
+	int ret_code = 0;
 
 	sd_entry = &hmc_info->sd_table.sd_entry[idx];
 
@@ -318,9 +318,9 @@
  * @idx: segment descriptor index to find the relevant page descriptor
  * @is_pf: used to distinguish between VF and PF
  **/
-i40e_status i40e_remove_pd_page_new(struct i40e_hw *hw,
-					      struct i40e_hmc_info *hmc_info,
-					      u32 idx, bool is_pf)
+int i40e_remove_pd_page_new(struct i40e_hw *hw,
+			    struct i40e_hmc_info *hmc_info,
+			    u32 idx, bool is_pf)
 {
 	struct i40e_hmc_sd_entry *sd_entry;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_hmc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_hmc.h
@@ -187,28 +187,28 @@
 	/* add one more to the limit to correct our range */		\
 	*(pd_limit) += 1;						\
 }
-i40e_status i40e_add_sd_table_entry(struct i40e_hw *hw,
-					      struct i40e_hmc_info *hmc_info,
-					      u32 sd_index,
-					      enum i40e_sd_entry_type type,
-					      u64 direct_mode_sz);
 
-i40e_status i40e_add_pd_table_entry(struct i40e_hw *hw,
-					      struct i40e_hmc_info *hmc_info,
-					      u32 pd_index,
-					      struct i40e_dma_mem *rsrc_pg);
-i40e_status i40e_remove_pd_bp(struct i40e_hw *hw,
-					struct i40e_hmc_info *hmc_info,
-					u32 idx);
-i40e_status i40e_prep_remove_sd_bp(struct i40e_hmc_info *hmc_info,
-					     u32 idx);
-i40e_status i40e_remove_sd_bp_new(struct i40e_hw *hw,
-					    struct i40e_hmc_info *hmc_info,
-					    u32 idx, bool is_pf);
-i40e_status i40e_prep_remove_pd_page(struct i40e_hmc_info *hmc_info,
-					       u32 idx);
-i40e_status i40e_remove_pd_page_new(struct i40e_hw *hw,
-					      struct i40e_hmc_info *hmc_info,
-					      u32 idx, bool is_pf);
+int i40e_add_sd_table_entry(struct i40e_hw *hw,
+			    struct i40e_hmc_info *hmc_info,
+			    u32 sd_index,
+			    enum i40e_sd_entry_type type,
+			    u64 direct_mode_sz);
+int i40e_add_pd_table_entry(struct i40e_hw *hw,
+			    struct i40e_hmc_info *hmc_info,
+			    u32 pd_index,
+			    struct i40e_dma_mem *rsrc_pg);
+int i40e_remove_pd_bp(struct i40e_hw *hw,
+		      struct i40e_hmc_info *hmc_info,
+		      u32 idx);
+int i40e_prep_remove_sd_bp(struct i40e_hmc_info *hmc_info,
+			   u32 idx);
+int i40e_remove_sd_bp_new(struct i40e_hw *hw,
+			  struct i40e_hmc_info *hmc_info,
+			  u32 idx, bool is_pf);
+int i40e_prep_remove_pd_page(struct i40e_hmc_info *hmc_info,
+			     u32 idx);
+int i40e_remove_pd_page_new(struct i40e_hw *hw,
+			    struct i40e_hmc_info *hmc_info,
+			    u32 idx, bool is_pf);
 
 #endif /* _I40E_HMC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_lan_hmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_lan_hmc.c
@@ -74,12 +74,12 @@
  * Assumptions:
  *   - HMC Resource Profile has been selected before calling this function.
  **/
-i40e_status i40e_init_lan_hmc(struct i40e_hw *hw, u32 txq_num,
-					u32 rxq_num, u32 fcoe_cntx_num,
-					u32 fcoe_filt_num)
+int i40e_init_lan_hmc(struct i40e_hw *hw, u32 txq_num,
+		      u32 rxq_num, u32 fcoe_cntx_num,
+		      u32 fcoe_filt_num)
 {
 	struct i40e_hmc_obj_info *obj, *full_obj;
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 	u64 l2fpm_size;
 	u32 size_exp;
 
@@ -229,11 +229,11 @@
  *	1. caller can deallocate the memory used by pd after this function
  *	   returns.
  **/
-static i40e_status i40e_remove_pd_page(struct i40e_hw *hw,
-						 struct i40e_hmc_info *hmc_info,
-						 u32 idx)
+static int i40e_remove_pd_page(struct i40e_hw *hw,
+			       struct i40e_hmc_info *hmc_info,
+			       u32 idx)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	if (!i40e_prep_remove_pd_page(hmc_info, idx))
 		ret_code = i40e_remove_pd_page_new(hw, hmc_info, idx, true);
@@ -256,11 +256,11 @@
  *	1. caller can deallocate the memory used by backing storage after this
  *	   function returns.
  **/
-static i40e_status i40e_remove_sd_bp(struct i40e_hw *hw,
-					       struct i40e_hmc_info *hmc_info,
-					       u32 idx)
+static int i40e_remove_sd_bp(struct i40e_hw *hw,
+			     struct i40e_hmc_info *hmc_info,
+			     u32 idx)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	if (!i40e_prep_remove_sd_bp(hmc_info, idx))
 		ret_code = i40e_remove_sd_bp_new(hw, hmc_info, idx, true);
@@ -276,15 +276,15 @@
  * This will allocate memory for PDs and backing pages and populate
  * the sd and pd entries.
  **/
-static i40e_status i40e_create_lan_hmc_object(struct i40e_hw *hw,
-				struct i40e_hmc_lan_create_obj_info *info)
+static int i40e_create_lan_hmc_object(struct i40e_hw *hw,
+				      struct i40e_hmc_lan_create_obj_info *info)
 {
-	i40e_status ret_code = 0;
 	struct i40e_hmc_sd_entry *sd_entry;
 	u32 pd_idx1 = 0, pd_lmt1 = 0;
 	u32 pd_idx = 0, pd_lmt = 0;
 	bool pd_error = false;
 	u32 sd_idx, sd_lmt;
+	int ret_code = 0;
 	u64 sd_size;
 	u32 i, j;
 
@@ -435,13 +435,13 @@
  * - This function will be called after i40e_init_lan_hmc() and before
  *   any LAN/FCoE HMC objects can be created.
  **/
-i40e_status i40e_configure_lan_hmc(struct i40e_hw *hw,
-					     enum i40e_hmc_model model)
+int i40e_configure_lan_hmc(struct i40e_hw *hw,
+			   enum i40e_hmc_model model)
 {
 	struct i40e_hmc_lan_create_obj_info info;
-	i40e_status ret_code = 0;
 	u8 hmc_fn_id = hw->hmc.hmc_fn_id;
 	struct i40e_hmc_obj_info *obj;
+	int ret_code = 0;
 
 	/* Initialize part of the create object info struct */
 	info.hmc_info = &hw->hmc;
@@ -520,13 +520,13 @@
  * caller should deallocate memory allocated previously for
  * book-keeping information about PDs and backing storage.
  **/
-static i40e_status i40e_delete_lan_hmc_object(struct i40e_hw *hw,
-				struct i40e_hmc_lan_delete_obj_info *info)
+static int i40e_delete_lan_hmc_object(struct i40e_hw *hw,
+				      struct i40e_hmc_lan_delete_obj_info *info)
 {
-	i40e_status ret_code = 0;
 	struct i40e_hmc_pd_table *pd_table;
 	u32 pd_idx, pd_lmt, rel_pd_idx;
 	u32 sd_idx, sd_lmt;
+	int ret_code = 0;
 	u32 i, j;
 
 	if (NULL == info) {
@@ -632,10 +632,10 @@
  * This must be called by drivers as they are shutting down and being
  * removed from the OS.
  **/
-i40e_status i40e_shutdown_lan_hmc(struct i40e_hw *hw)
+int i40e_shutdown_lan_hmc(struct i40e_hw *hw)
 {
 	struct i40e_hmc_lan_delete_obj_info info;
-	i40e_status ret_code;
+	int ret_code;
 
 	info.hmc_info = &hw->hmc;
 	info.rsrc_type = I40E_HMC_LAN_FULL;
@@ -915,9 +915,9 @@
  * @context_bytes: pointer to the context bit array (DMA memory)
  * @hmc_type: the type of HMC resource
  **/
-static i40e_status i40e_clear_hmc_context(struct i40e_hw *hw,
-					u8 *context_bytes,
-					enum i40e_hmc_lan_rsrc_type hmc_type)
+static int i40e_clear_hmc_context(struct i40e_hw *hw,
+				  u8 *context_bytes,
+				  enum i40e_hmc_lan_rsrc_type hmc_type)
 {
 	/* clean the bit array */
 	memset(context_bytes, 0, (u32)hw->hmc.hmc_obj[hmc_type].size);
@@ -931,9 +931,9 @@
  * @ce_info:  a description of the struct to be filled
  * @dest:     the struct to be filled
  **/
-static i40e_status i40e_set_hmc_context(u8 *context_bytes,
-					struct i40e_context_ele *ce_info,
-					u8 *dest)
+static int i40e_set_hmc_context(u8 *context_bytes,
+				struct i40e_context_ele *ce_info,
+				u8 *dest)
 {
 	int f;
 
@@ -973,18 +973,18 @@
  * base pointer.  This function is used for LAN Queue contexts.
  **/
 static
-i40e_status i40e_hmc_get_object_va(struct i40e_hw *hw, u8 **object_base,
-				   enum i40e_hmc_lan_rsrc_type rsrc_type,
-				   u32 obj_idx)
+int i40e_hmc_get_object_va(struct i40e_hw *hw, u8 **object_base,
+			   enum i40e_hmc_lan_rsrc_type rsrc_type,
+			   u32 obj_idx)
 {
 	struct i40e_hmc_info *hmc_info = &hw->hmc;
 	u32 obj_offset_in_sd, obj_offset_in_pd;
 	struct i40e_hmc_sd_entry *sd_entry;
 	struct i40e_hmc_pd_entry *pd_entry;
 	u32 pd_idx, pd_lmt, rel_pd_idx;
-	i40e_status ret_code = 0;
 	u64 obj_offset_in_fpm;
 	u32 sd_idx, sd_lmt;
+	int ret_code = 0;
 
 	if (NULL == hmc_info) {
 		ret_code = I40E_ERR_BAD_PTR;
@@ -1042,11 +1042,11 @@
  * @hw:    the hardware struct
  * @queue: the queue we care about
  **/
-i40e_status i40e_clear_lan_tx_queue_context(struct i40e_hw *hw,
-						      u16 queue)
+int i40e_clear_lan_tx_queue_context(struct i40e_hw *hw,
+				    u16 queue)
 {
-	i40e_status err;
 	u8 *context_bytes;
+	int err;
 
 	err = i40e_hmc_get_object_va(hw, &context_bytes,
 				     I40E_HMC_LAN_TX, queue);
@@ -1062,12 +1062,12 @@
  * @queue: the queue we care about
  * @s:     the struct to be filled
  **/
-i40e_status i40e_set_lan_tx_queue_context(struct i40e_hw *hw,
-						    u16 queue,
-						    struct i40e_hmc_obj_txq *s)
+int i40e_set_lan_tx_queue_context(struct i40e_hw *hw,
+				  u16 queue,
+				  struct i40e_hmc_obj_txq *s)
 {
-	i40e_status err;
 	u8 *context_bytes;
+	int err;
 
 	err = i40e_hmc_get_object_va(hw, &context_bytes,
 				     I40E_HMC_LAN_TX, queue);
@@ -1083,11 +1083,11 @@
  * @hw:    the hardware struct
  * @queue: the queue we care about
  **/
-i40e_status i40e_clear_lan_rx_queue_context(struct i40e_hw *hw,
-						      u16 queue)
+int i40e_clear_lan_rx_queue_context(struct i40e_hw *hw,
+				    u16 queue)
 {
-	i40e_status err;
 	u8 *context_bytes;
+	int err;
 
 	err = i40e_hmc_get_object_va(hw, &context_bytes,
 				     I40E_HMC_LAN_RX, queue);
@@ -1103,12 +1103,12 @@
  * @queue: the queue we care about
  * @s:     the struct to be filled
  **/
-i40e_status i40e_set_lan_rx_queue_context(struct i40e_hw *hw,
-						    u16 queue,
-						    struct i40e_hmc_obj_rxq *s)
+int i40e_set_lan_rx_queue_context(struct i40e_hw *hw,
+				  u16 queue,
+				  struct i40e_hmc_obj_rxq *s)
 {
-	i40e_status err;
 	u8 *context_bytes;
+	int err;
 
 	err = i40e_hmc_get_object_va(hw, &context_bytes,
 				     I40E_HMC_LAN_RX, queue);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_lan_hmc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_lan_hmc.h
@@ -137,22 +137,22 @@
 	u32 count;
 };
 
-i40e_status i40e_init_lan_hmc(struct i40e_hw *hw, u32 txq_num,
-					u32 rxq_num, u32 fcoe_cntx_num,
-					u32 fcoe_filt_num);
-i40e_status i40e_configure_lan_hmc(struct i40e_hw *hw,
-					     enum i40e_hmc_model model);
-i40e_status i40e_shutdown_lan_hmc(struct i40e_hw *hw);
+int i40e_init_lan_hmc(struct i40e_hw *hw, u32 txq_num,
+		      u32 rxq_num, u32 fcoe_cntx_num,
+		      u32 fcoe_filt_num);
+int i40e_configure_lan_hmc(struct i40e_hw *hw,
+			   enum i40e_hmc_model model);
+int i40e_shutdown_lan_hmc(struct i40e_hw *hw);
 
-i40e_status i40e_clear_lan_tx_queue_context(struct i40e_hw *hw,
-						      u16 queue);
-i40e_status i40e_set_lan_tx_queue_context(struct i40e_hw *hw,
-						    u16 queue,
-						    struct i40e_hmc_obj_txq *s);
-i40e_status i40e_clear_lan_rx_queue_context(struct i40e_hw *hw,
-						      u16 queue);
-i40e_status i40e_set_lan_rx_queue_context(struct i40e_hw *hw,
-						    u16 queue,
-						    struct i40e_hmc_obj_rxq *s);
+int i40e_clear_lan_tx_queue_context(struct i40e_hw *hw,
+				    u16 queue);
+int i40e_set_lan_tx_queue_context(struct i40e_hw *hw,
+				  u16 queue,
+				  struct i40e_hmc_obj_txq *s);
+int i40e_clear_lan_rx_queue_context(struct i40e_hw *hw,
+				    u16 queue);
+int i40e_set_lan_rx_queue_context(struct i40e_hw *hw,
+				  u16 queue,
+				  struct i40e_hmc_obj_rxq *s);
 
 #endif /* _I40E_LAN_HMC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -99,6 +99,30 @@
 
 static struct workqueue_struct *i40e_wq;
 
+static void netdev_hw_addr_refcnt(struct i40e_mac_filter *f,
+				  struct net_device *netdev, int delta)
+{
+	struct netdev_hw_addr_list *ha_list;
+	struct netdev_hw_addr *ha;
+
+	if (!f || !netdev)
+		return;
+
+	if (is_unicast_ether_addr(f->macaddr) || is_link_local_ether_addr(f->macaddr))
+		ha_list = &netdev->uc;
+	else
+		ha_list = &netdev->mc;
+
+	netdev_hw_addr_list_for_each(ha, ha_list) {
+		if (ether_addr_equal(ha->addr, f->macaddr)) {
+			ha->refcount += delta;
+			if (ha->refcount <= 0)
+				ha->refcount = 1;
+			break;
+		}
+	}
+}
+
 /**
  * i40e_allocate_dma_mem_d - OS specific memory alloc for shared code
  * @hw:   pointer to the HW structure
@@ -178,10 +202,6 @@
  * @id: an owner id to stick on the items assigned
  *
  * Returns the base item index of the lump, or negative for error
- *
- * The search_hint trick and lack of advanced fit-finding only work
- * because we're highly likely to have all the same size lump requests.
- * Linear search time and any fragmentation should be minimal.
  **/
 static int i40e_get_lump(struct i40e_pf *pf, struct i40e_lump_tracking *pile,
 			 u16 needed, u16 id)
@@ -196,8 +216,21 @@
 		return -EINVAL;
 	}
 
-	/* start the linear search with an imperfect hint */
-	i = pile->search_hint;
+	/* Allocate last queue in the pile for FDIR VSI queue
+	 * so it doesn't fragment the qp_pile
+	 */
+	if (pile == pf->qp_pile && pf->vsi[id]->type == I40E_VSI_FDIR) {
+		if (pile->list[pile->num_entries - 1] & I40E_PILE_VALID_BIT) {
+			dev_err(&pf->pdev->dev,
+				"Cannot allocate queue %d for I40E_VSI_FDIR\n",
+				pile->num_entries - 1);
+			return -ENOMEM;
+		}
+		pile->list[pile->num_entries - 1] = id | I40E_PILE_VALID_BIT;
+		return pile->num_entries - 1;
+	}
+
+	i = 0;
 	while (i < pile->num_entries) {
 		/* skip already allocated entries */
 		if (pile->list[i] & I40E_PILE_VALID_BIT) {
@@ -216,7 +249,6 @@
 			for (j = 0; j < needed; j++)
 				pile->list[i+j] = id | I40E_PILE_VALID_BIT;
 			ret = i;
-			pile->search_hint = i + j;
 			break;
 		}
 
@@ -239,7 +271,7 @@
 {
 	int valid_id = (id | I40E_PILE_VALID_BIT);
 	int count = 0;
-	int i;
+	u16 i;
 
 	if (!pile || index >= pile->num_entries)
 		return -EINVAL;
@@ -251,8 +283,6 @@
 		count++;
 	}
 
-	if (count && index < pile->search_hint)
-		pile->search_hint = index;
 
 	return count;
 }
@@ -359,7 +389,9 @@
 		set_bit(__I40E_GLOBAL_RESET_REQUESTED, pf->state);
 		break;
 	default:
-		netdev_err(netdev, "tx_timeout recovery unsuccessful\n");
+		netdev_err(netdev, "tx_timeout recovery unsuccessful, device is in non-recoverable state.\n");
+		set_bit(__I40E_DOWN_REQUESTED, pf->state);
+		set_bit(__I40E_VSI_DOWN_REQUESTED, vsi->state);
 		break;
 	}
 
@@ -526,6 +558,47 @@
 }
 
 /**
+ * i40e_compute_pci_to_hw_id - compute index form PCI function.
+ * @vsi: ptr to the VSI to read from.
+ * @hw: ptr to the hardware info.
+ **/
+static u32 i40e_compute_pci_to_hw_id(struct i40e_vsi *vsi, struct i40e_hw *hw)
+{
+	int pf_count = i40e_get_pf_count(hw);
+
+	if (vsi->type == I40E_VSI_SRIOV)
+		return (hw->port * BIT(7)) / pf_count + vsi->vf_id;
+
+	return hw->port + BIT(7);
+}
+
+/**
+ * i40e_stat_update64 - read and update a 64 bit stat from the chip.
+ * @hw: ptr to the hardware info.
+ * @hireg: the high 32 bit reg to read.
+ * @loreg: the low 32 bit reg to read.
+ * @offset_loaded: has the initial offset been loaded yet.
+ * @offset: ptr to current offset value.
+ * @stat: ptr to the stat.
+ *
+ * Since the device stats are not reset at PFReset, they will not
+ * be zeroed when the driver starts.  We'll save the first values read
+ * and use them as offsets to be subtracted from the raw values in order
+ * to report stats that count from zero.
+ **/
+static void i40e_stat_update64(struct i40e_hw *hw, u32 hireg, u32 loreg,
+			       bool offset_loaded, u64 *offset, u64 *stat)
+{
+	u64 new_data;
+
+	new_data = rd64(hw, loreg);
+
+	if (!offset_loaded || new_data < *offset)
+		*offset = new_data;
+	*stat = new_data - *offset;
+}
+
+/**
  * i40e_stat_update48 - read and update a 48 bit stat from the chip
  * @hw: ptr to the hardware info
  * @hireg: the high 32 bit reg to read
@@ -597,6 +670,34 @@
 }
 
 /**
+ * i40e_stats_update_rx_discards - update rx_discards.
+ * @vsi: ptr to the VSI to be updated.
+ * @hw: ptr to the hardware info.
+ * @stat_idx: VSI's stat_counter_idx.
+ * @offset_loaded: ptr to the VSI's stat_offsets_loaded.
+ * @stat_offset: ptr to stat_offset to store first read of specific register.
+ * @stat: ptr to VSI's stat to be updated.
+ **/
+static void
+i40e_stats_update_rx_discards(struct i40e_vsi *vsi, struct i40e_hw *hw,
+			      int stat_idx, bool offset_loaded,
+			      struct i40e_eth_stats *stat_offset,
+			      struct i40e_eth_stats *stat)
+{
+	u64 rx_rdpc, rx_rxerr;
+
+	i40e_stat_update32(hw, I40E_GLV_RDPC(stat_idx), offset_loaded,
+			   &stat_offset->rx_discards, &rx_rdpc);
+	i40e_stat_update64(hw,
+			   I40E_GL_RXERR1H(i40e_compute_pci_to_hw_id(vsi, hw)),
+			   I40E_GL_RXERR1L(i40e_compute_pci_to_hw_id(vsi, hw)),
+			   offset_loaded, &stat_offset->rx_discards_other,
+			   &rx_rxerr);
+
+	stat->rx_discards = rx_rdpc + rx_rxerr;
+}
+
+/**
  * i40e_update_eth_stats - Update VSI-specific ethernet statistics counters.
  * @vsi: the VSI to be updated
  **/
@@ -655,6 +756,10 @@
 			   I40E_GLV_BPTCL(stat_idx),
 			   vsi->stat_offsets_loaded,
 			   &oes->tx_broadcast, &es->tx_broadcast);
+
+	i40e_stats_update_rx_discards(vsi, hw, stat_idx,
+				      vsi->stat_offsets_loaded, oes, es);
+
 	vsi->stat_offsets_loaded = true;
 }
 
@@ -754,9 +859,9 @@
 	struct rtnl_link_stats64 *ns;   /* netdev stats */
 	struct i40e_eth_stats *oes;
 	struct i40e_eth_stats *es;     /* device's eth stats */
-	u32 tx_restart, tx_busy;
+	u64 tx_restart, tx_busy;
 	struct i40e_ring *p;
-	u32 rx_page, rx_buf;
+	u64 rx_page, rx_buf;
 	u64 bytes, packets;
 	unsigned int start;
 	u64 tx_linearize;
@@ -1126,8 +1231,12 @@
 	int bkt;
 	int cnt = 0;
 
-	hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist)
-		++cnt;
+	hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
+		if (f->state == I40E_FILTER_NEW ||
+		    f->state == I40E_FILTER_NEW_SYNC ||
+		    f->state == I40E_FILTER_ACTIVE)
+			++cnt;
+	}
 
 	return cnt;
 }
@@ -1311,6 +1420,8 @@
 
 			new->f = add_head;
 			new->state = add_head->state;
+			if (add_head->state == I40E_FILTER_NEW)
+				add_head->state = I40E_FILTER_NEW_SYNC;
 
 			/* Add the new filter to the tmp list */
 			hlist_add_head(&new->hlist, tmp_add_list);
@@ -1328,6 +1439,116 @@
 }
 
 /**
+ * i40e_get_vf_new_vlan - Get new vlan id on a vf
+ * @vsi: the vsi to configure
+ * @new_mac: new mac filter to be added
+ * @f: existing mac filter, replaced with new_mac->f if new_mac is not NULL
+ * @vlan_filters: the number of active VLAN filters
+ * @trusted: flag if the VF is trusted
+ *
+ * Get new VLAN id based on current VLAN filters, trust, PVID
+ * and vf-vlan-prune-disable flag.
+ *
+ * Returns the value of the new vlan filter or
+ * the old value if no new filter is needed.
+ */
+static s16 i40e_get_vf_new_vlan(struct i40e_vsi *vsi,
+				struct i40e_new_mac_filter *new_mac,
+				struct i40e_mac_filter *f,
+				int vlan_filters,
+				bool trusted)
+{
+	s16 pvid = le16_to_cpu(vsi->info.pvid);
+	struct i40e_pf *pf = vsi->back;
+	bool is_any;
+
+	if (new_mac)
+		f = new_mac->f;
+
+	if (pvid && f->vlan != pvid)
+		return pvid;
+
+	is_any = (trusted ||
+		  !(pf->flags & I40E_FLAG_VF_VLAN_PRUNING));
+
+	if ((vlan_filters && f->vlan == I40E_VLAN_ANY) ||
+	    (!is_any && !vlan_filters && f->vlan == I40E_VLAN_ANY) ||
+	    (is_any && !vlan_filters && f->vlan == 0)) {
+		if (is_any)
+			return I40E_VLAN_ANY;
+		else
+			return 0;
+	}
+
+	return f->vlan;
+}
+
+/**
+ * i40e_correct_vf_mac_vlan_filters - Correct non-VLAN VF filters if necessary
+ * @vsi: the vsi to configure
+ * @tmp_add_list: list of filters ready to be added
+ * @tmp_del_list: list of filters ready to be deleted
+ * @vlan_filters: the number of active VLAN filters
+ * @trusted: flag if the VF is trusted
+ *
+ * Correct VF VLAN filters based on current VLAN filters, trust, PVID
+ * and vf-vlan-prune-disable flag.
+ *
+ * In case of memory allocation failure return -ENOMEM. Otherwise, return 0.
+ *
+ * This function is only expected to be called from within
+ * i40e_sync_vsi_filters.
+ *
+ * NOTE: This function expects to be called while under the
+ * mac_filter_hash_lock
+ */
+static int i40e_correct_vf_mac_vlan_filters(struct i40e_vsi *vsi,
+					    struct hlist_head *tmp_add_list,
+					    struct hlist_head *tmp_del_list,
+					    int vlan_filters,
+					    bool trusted)
+{
+	struct i40e_mac_filter *f, *add_head;
+	struct i40e_new_mac_filter *new_mac;
+	struct hlist_node *h;
+	int bkt, new_vlan;
+
+	hlist_for_each_entry(new_mac, tmp_add_list, hlist) {
+		new_mac->f->vlan = i40e_get_vf_new_vlan(vsi, new_mac, NULL,
+							vlan_filters, trusted);
+	}
+
+	hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
+		new_vlan = i40e_get_vf_new_vlan(vsi, NULL, f, vlan_filters,
+						trusted);
+		if (new_vlan != f->vlan) {
+			add_head = i40e_add_filter(vsi, f->macaddr, new_vlan);
+			if (!add_head)
+				return -ENOMEM;
+			/* Create a temporary i40e_new_mac_filter */
+			new_mac = kzalloc(sizeof(*new_mac), GFP_ATOMIC);
+			if (!new_mac)
+				return -ENOMEM;
+			new_mac->f = add_head;
+			new_mac->state = add_head->state;
+			if (add_head->state == I40E_FILTER_NEW)
+				add_head->state = I40E_FILTER_NEW_SYNC;
+
+			/* Add the new filter to the tmp list */
+			hlist_add_head(&new_mac->hlist, tmp_add_list);
+
+			/* Put the original filter into the delete list */
+			f->state = I40E_FILTER_REMOVE;
+			hash_del(&f->hlist);
+			hlist_add_head(&f->hlist, tmp_del_list);
+		}
+	}
+
+	vsi->has_vlan_filter = !!vlan_filters;
+	return 0;
+}
+
+/**
  * i40e_rm_default_mac_filter - Remove the default MAC filter set by NVM
  * @vsi: the PF Main VSI - inappropriate for any other VSI
  * @macaddr: the MAC address
@@ -1496,6 +1717,7 @@
 	struct hlist_node *h;
 	int bkt;
 
+	lockdep_assert_held(&vsi->mac_filter_hash_lock);
 	if (vsi->info.pvid)
 		return i40e_add_filter(vsi, macaddr,
 				       le16_to_cpu(vsi->info.pvid));
@@ -1587,18 +1809,18 @@
 	 */
 	spin_lock_bh(&vsi->mac_filter_hash_lock);
 	i40e_del_mac_filter(vsi, netdev->dev_addr);
-	ether_addr_copy(netdev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(netdev, addr->sa_data);
 	i40e_add_mac_filter(vsi, netdev->dev_addr);
 	spin_unlock_bh(&vsi->mac_filter_hash_lock);
 
 	if (vsi->type == I40E_VSI_MAIN) {
-		i40e_status ret;
+		int ret;
 
 		ret = i40e_aq_mac_address_write(hw, I40E_AQC_WRITE_TYPE_LAA_WOL,
 						addr->sa_data, NULL);
 		if (ret)
-			netdev_info(netdev, "Ignoring error from firmware on LAA update, status %s, AQ ret %s\n",
-				    i40e_stat_str(hw, ret),
+			netdev_info(netdev, "Ignoring error from firmware on LAA update, status %d, AQ ret %s\n",
+				    ret,
 				    i40e_aq_str(hw, hw->aq.asq_last_status));
 	}
 
@@ -1629,8 +1851,8 @@
 		ret = i40e_aq_set_rss_key(hw, vsi->id, seed_dw);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "Cannot set RSS key, err %s aq_err %s\n",
-				 i40e_stat_str(hw, ret),
+				 "Cannot set RSS key, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 			return ret;
 		}
@@ -1641,8 +1863,8 @@
 		ret = i40e_aq_set_rss_lut(hw, vsi->id, pf_lut, lut, lut_size);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "Cannot set RSS lut, err %s aq_err %s\n",
-				 i40e_stat_str(hw, ret),
+				 "Cannot set RSS lut, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 			return ret;
 		}
@@ -1790,6 +2012,7 @@
 				     bool is_add)
 {
 	struct i40e_pf *pf = vsi->back;
+	u16 num_tc_qps = 0;
 	u16 sections = 0;
 	u8 netdev_tc = 0;
 	u16 numtc = 1;
@@ -1797,13 +2020,37 @@
 	u8 offset;
 	u16 qmap;
 	int i;
-	u16 num_tc_qps = 0;
 
 	sections = I40E_AQ_VSI_PROP_QUEUE_MAP_VALID;
 	offset = 0;
+	/* zero out queue mapping, it will get updated on the end of the function */
+	memset(ctxt->info.queue_mapping, 0, sizeof(ctxt->info.queue_mapping));
+
+	if (vsi->type == I40E_VSI_MAIN) {
+		/* This code helps add more queue to the VSI if we have
+		 * more cores than RSS can support, the higher cores will
+		 * be served by ATR or other filters. Furthermore, the
+		 * non-zero req_queue_pairs says that user requested a new
+		 * queue count via ethtool's set_channels, so use this
+		 * value for queues distribution across traffic classes
+		 * We need at least one queue pair for the interface
+		 * to be usable as we see in else statement.
+		 */
+		if (vsi->req_queue_pairs > 0)
+			vsi->num_queue_pairs = vsi->req_queue_pairs;
+		else if (pf->flags & I40E_FLAG_MSIX_ENABLED)
+			vsi->num_queue_pairs = pf->num_lan_msix;
+		else
+			vsi->num_queue_pairs = 1;
+	}
 
 	/* Number of queues per enabled TC */
-	num_tc_qps = vsi->alloc_queue_pairs;
+	if (vsi->type == I40E_VSI_MAIN ||
+	    (vsi->type == I40E_VSI_SRIOV && vsi->num_queue_pairs != 0))
+		num_tc_qps = vsi->num_queue_pairs;
+	else
+		num_tc_qps = vsi->alloc_queue_pairs;
+
 	if (enabled_tc && (vsi->back->flags & I40E_FLAG_DCB_ENABLED)) {
 		/* Find numtc from enabled TC bitmap */
 		for (i = 0, numtc = 0; i < I40E_MAX_TRAFFIC_CLASS; i++) {
@@ -1881,15 +2128,11 @@
 		}
 		ctxt->info.tc_mapping[i] = cpu_to_le16(qmap);
 	}
-
-	/* Set actual Tx/Rx queue pairs */
-	vsi->num_queue_pairs = offset;
-	if ((vsi->type == I40E_VSI_MAIN) && (numtc == 1)) {
-		if (vsi->req_queue_pairs > 0)
-			vsi->num_queue_pairs = vsi->req_queue_pairs;
-		else if (pf->flags & I40E_FLAG_MSIX_ENABLED)
-			vsi->num_queue_pairs = pf->num_lan_msix;
-	}
+	/* Do not change previously set num_queue_pairs for PFs and VFs*/
+	if ((vsi->type == I40E_VSI_MAIN && numtc != 1) ||
+	    (vsi->type == I40E_VSI_SRIOV && vsi->num_queue_pairs == 0) ||
+	    (vsi->type != I40E_VSI_MAIN && vsi->type != I40E_VSI_SRIOV))
+		vsi->num_queue_pairs = offset;
 
 	/* Scheduler section valid can only be set for ADD VSI */
 	if (is_add) {
@@ -2019,6 +2262,7 @@
 	hlist_for_each_entry_safe(new, h, from, hlist) {
 		/* We can simply free the wrapper structure */
 		hlist_del(&new->hlist);
+		netdev_hw_addr_refcnt(new->f, vsi->netdev, -1);
 		kfree(new);
 	}
 }
@@ -2101,7 +2345,7 @@
 			  int num_del, int *retval)
 {
 	struct i40e_hw *hw = &vsi->back->hw;
-	i40e_status aq_ret;
+	int aq_ret;
 	int aq_err;
 
 	aq_ret = i40e_aq_remove_macvlan(hw, vsi->seid, list, num_del, NULL);
@@ -2111,8 +2355,8 @@
 	if (aq_ret && !(aq_err == I40E_AQ_RC_ENOENT)) {
 		*retval = -EIO;
 		dev_info(&vsi->back->pdev->dev,
-			 "ignoring delete macvlan error on %s, err %s, aq_err %s\n",
-			 vsi_name, i40e_stat_str(hw, aq_ret),
+			 "ignoring delete macvlan error on %s, err %d, aq_err %s\n",
+			 vsi_name, aq_ret,
 			 i40e_aq_str(hw, aq_err));
 	}
 }
@@ -2174,13 +2418,14 @@
  *
  * Returns status indicating success or failure;
  **/
-static i40e_status
+static int
 i40e_aqc_broadcast_filter(struct i40e_vsi *vsi, const char *vsi_name,
 			  struct i40e_mac_filter *f)
 {
-	bool enable = f->state == I40E_FILTER_NEW;
+	bool enable = f->state == I40E_FILTER_NEW ||
+		      f->state == I40E_FILTER_NEW_SYNC;
 	struct i40e_hw *hw = &vsi->back->hw;
-	i40e_status aq_ret;
+	int aq_ret;
 
 	if (f->vlan == I40E_VLAN_ANY) {
 		aq_ret = i40e_aq_set_vsi_broadcast(hw,
@@ -2219,7 +2464,7 @@
 {
 	struct i40e_vsi *vsi = pf->vsi[pf->lan_vsi];
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status aq_ret;
+	int aq_ret;
 
 	if (vsi->type == I40E_VSI_MAIN &&
 	    pf->lan_veb != I40E_NO_VEB &&
@@ -2239,8 +2484,8 @@
 							   NULL);
 		if (aq_ret) {
 			dev_info(&pf->pdev->dev,
-				 "Set default VSI failed, err %s, aq_err %s\n",
-				 i40e_stat_str(hw, aq_ret),
+				 "Set default VSI failed, err %d, aq_err %s\n",
+				 aq_ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 		}
 	} else {
@@ -2251,8 +2496,8 @@
 						  true);
 		if (aq_ret) {
 			dev_info(&pf->pdev->dev,
-				 "set unicast promisc failed, err %s, aq_err %s\n",
-				 i40e_stat_str(hw, aq_ret),
+				 "set unicast promisc failed, err %d, aq_err %s\n",
+				 aq_ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 		}
 		aq_ret = i40e_aq_set_vsi_multicast_promiscuous(
@@ -2261,8 +2506,8 @@
 						  promisc, NULL);
 		if (aq_ret) {
 			dev_info(&pf->pdev->dev,
-				 "set multicast promisc failed, err %s, aq_err %s\n",
-				 i40e_stat_str(hw, aq_ret),
+				 "set multicast promisc failed, err %d, aq_err %s\n",
+				 aq_ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 		}
 	}
@@ -2292,12 +2537,12 @@
 	unsigned int vlan_filters = 0;
 	char vsi_name[16] = "PF";
 	int filter_list_len = 0;
-	i40e_status aq_ret = 0;
 	u32 changed_flags = 0;
 	struct hlist_node *h;
 	struct i40e_pf *pf;
 	int num_add = 0;
 	int num_del = 0;
+	int aq_ret = 0;
 	int retval = 0;
 	u16 cmd_flags;
 	int list_size;
@@ -2352,6 +2597,7 @@
 
 				/* Add it to the hash list */
 				hlist_add_head(&new->hlist, &tmp_add_list);
+				f->state = I40E_FILTER_NEW_SYNC;
 			}
 
 			/* Count the number of active (current and new) VLAN
@@ -2362,10 +2608,18 @@
 				vlan_filters++;
 		}
 
-		retval = i40e_correct_mac_vlan_filters(vsi,
-						       &tmp_add_list,
-						       &tmp_del_list,
-						       vlan_filters);
+		if (vsi->type != I40E_VSI_SRIOV)
+			retval = i40e_correct_mac_vlan_filters
+				(vsi, &tmp_add_list, &tmp_del_list,
+				 vlan_filters);
+		else if (pf->vf)
+			retval = i40e_correct_vf_mac_vlan_filters
+				(vsi, &tmp_add_list, &tmp_del_list,
+				 vlan_filters, pf->vf[vsi->vf_id].trusted);
+
+		hlist_for_each_entry(new, &tmp_add_list, hlist)
+			netdev_hw_addr_refcnt(new->f, vsi->netdev, 1);
+
 		if (retval)
 			goto err_no_memory_locked;
 
@@ -2495,9 +2749,11 @@
 		spin_lock_bh(&vsi->mac_filter_hash_lock);
 		hlist_for_each_entry_safe(new, h, &tmp_add_list, hlist) {
 			/* Only update the state if we're still NEW */
-			if (new->f->state == I40E_FILTER_NEW)
+			if (new->f->state == I40E_FILTER_NEW ||
+			    new->f->state == I40E_FILTER_NEW_SYNC)
 				new->f->state = new->state;
 			hlist_del(&new->hlist);
+			netdev_hw_addr_refcnt(new->f, vsi->netdev, -1);
 			kfree(new);
 		}
 		spin_unlock_bh(&vsi->mac_filter_hash_lock);
@@ -2530,7 +2786,8 @@
 	}
 
 	/* if the VF is not trusted do not do promisc */
-	if ((vsi->type == I40E_VSI_SRIOV) && !pf->vf[vsi->vf_id].trusted) {
+	if (vsi->type == I40E_VSI_SRIOV && pf->vf &&
+	    !pf->vf[vsi->vf_id].trusted) {
 		clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state);
 		goto out;
 	}
@@ -2556,9 +2813,9 @@
 			retval = i40e_aq_rc_to_posix(aq_ret,
 						     hw->aq.asq_last_status);
 			dev_info(&pf->pdev->dev,
-				 "set multi promisc failed on %s, err %s aq_err %s\n",
+				 "set multi promisc failed on %s, err %d aq_err %s\n",
 				 vsi_name,
-				 i40e_stat_str(hw, aq_ret),
+				 aq_ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 		} else {
 			dev_info(&pf->pdev->dev, "%s allmulti mode.\n",
@@ -2576,10 +2833,10 @@
 			retval = i40e_aq_rc_to_posix(aq_ret,
 						     hw->aq.asq_last_status);
 			dev_info(&pf->pdev->dev,
-				 "Setting promiscuous %s failed on %s, err %s aq_err %s\n",
+				 "Setting promiscuous %s failed on %s, err %d aq_err %s\n",
 				 cur_promisc ? "on" : "off",
 				 vsi_name,
-				 i40e_stat_str(hw, aq_ret),
+				 aq_ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 		}
 	}
@@ -2623,7 +2880,8 @@
 
 	for (v = 0; v < pf->num_alloc_vsi; v++) {
 		if (pf->vsi[v] &&
-		    (pf->vsi[v]->flags & I40E_VSI_FLAG_FILTER_CHANGED)) {
+		    (pf->vsi[v]->flags & I40E_VSI_FLAG_FILTER_CHANGED) &&
+		    !test_bit(__I40E_VSI_RELEASING, pf->vsi[v]->state)) {
 			int ret = i40e_sync_vsi_filters(pf->vsi[v]);
 
 			if (ret) {
@@ -2662,7 +2920,7 @@
 	struct i40e_pf *pf = vsi->back;
 
 	if (i40e_enabled_xdp_vsi(vsi)) {
-		int frame_size = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+		int frame_size = new_mtu + I40E_PACKET_HDR_PAD;
 
 		if (frame_size > i40e_max_xdp_frame_size(vsi))
 			return -EINVAL;
@@ -2706,7 +2964,7 @@
 void i40e_vlan_stripping_enable(struct i40e_vsi *vsi)
 {
 	struct i40e_vsi_context ctxt;
-	i40e_status ret;
+	int ret;
 
 	/* Don't modify stripping options if a port VLAN is active */
 	if (vsi->info.pvid)
@@ -2726,8 +2984,8 @@
 	ret = i40e_aq_update_vsi_params(&vsi->back->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&vsi->back->pdev->dev,
-			 "update vlan stripping failed, err %s aq_err %s\n",
-			 i40e_stat_str(&vsi->back->hw, ret),
+			 "update vlan stripping failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&vsi->back->hw,
 				     vsi->back->hw.aq.asq_last_status));
 	}
@@ -2740,7 +2998,7 @@
 void i40e_vlan_stripping_disable(struct i40e_vsi *vsi)
 {
 	struct i40e_vsi_context ctxt;
-	i40e_status ret;
+	int ret;
 
 	/* Don't modify stripping options if a port VLAN is active */
 	if (vsi->info.pvid)
@@ -2761,8 +3019,8 @@
 	ret = i40e_aq_update_vsi_params(&vsi->back->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&vsi->back->pdev->dev,
-			 "update vlan stripping failed, err %s aq_err %s\n",
-			 i40e_stat_str(&vsi->back->hw, ret),
+			 "update vlan stripping failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&vsi->back->hw,
 				     vsi->back->hw.aq.asq_last_status));
 	}
@@ -2788,8 +3046,21 @@
 	int bkt;
 
 	hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
-		if (f->state == I40E_FILTER_REMOVE)
+		/* If we're asked to add a filter that has been marked for
+		 * removal, it is safe to simply restore it to active state.
+		 * __i40e_del_filter will have simply deleted any filters which
+		 * were previously marked NEW or FAILED, so if it is currently
+		 * marked REMOVE it must have previously been ACTIVE. Since we
+		 * haven't yet run the sync filters task, just restore this
+		 * filter to the ACTIVE state so that the sync task leaves it
+		 * in place.
+		 */
+		if (f->state == I40E_FILTER_REMOVE && f->vlan == vid) {
+			f->state = I40E_FILTER_ACTIVE;
+			continue;
+		} else if (f->state == I40E_FILTER_REMOVE) {
 			continue;
+		}
 		add_f = i40e_add_filter(vsi, f->macaddr, vid);
 		if (!add_f) {
 			dev_info(&vsi->back->pdev->dev,
@@ -2980,7 +3251,7 @@
 int i40e_vsi_add_pvid(struct i40e_vsi *vsi, u16 vid)
 {
 	struct i40e_vsi_context ctxt;
-	i40e_status ret;
+	int ret;
 
 	vsi->info.valid_sections = cpu_to_le16(I40E_AQ_VSI_PROP_VLAN_VALID);
 	vsi->info.pvid = cpu_to_le16(vid);
@@ -2993,8 +3264,8 @@
 	ret = i40e_aq_update_vsi_params(&vsi->back->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&vsi->back->pdev->dev,
-			 "add pvid failed, err %s aq_err %s\n",
-			 i40e_stat_str(&vsi->back->hw, ret),
+			 "add pvid failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&vsi->back->hw,
 				     vsi->back->hw.aq.asq_last_status));
 		return -ENOENT;
@@ -3157,8 +3428,8 @@
 	u16 pf_q = vsi->base_queue + ring->queue_index;
 	struct i40e_hw *hw = &vsi->back->hw;
 	struct i40e_hmc_obj_txq tx_ctx;
-	i40e_status err = 0;
 	u32 qtx_ctl = 0;
+	int err = 0;
 
 	if (ring_is_xdp(ring))
 		ring->xsk_pool = i40e_xsk_pool(ring);
@@ -3282,7 +3553,7 @@
 	u16 pf_q = vsi->base_queue + ring->queue_index;
 	struct i40e_hw *hw = &vsi->back->hw;
 	struct i40e_hmc_obj_rxq rx_ctx;
-	i40e_status err = 0;
+	int err = 0;
 	bool ok;
 	int ret;
 
@@ -3294,12 +3565,8 @@
 	if (ring->vsi->type == I40E_VSI_MAIN)
 		xdp_rxq_info_unreg_mem_model(&ring->xdp_rxq);
 
-	kfree(ring->rx_bi);
 	ring->xsk_pool = i40e_xsk_pool(ring);
 	if (ring->xsk_pool) {
-		ret = i40e_alloc_rx_bi_zc(ring);
-		if (ret)
-			return ret;
 		ring->rx_buf_len =
 		  xsk_pool_get_rx_frame_size(ring->xsk_pool);
 		/* For AF_XDP ZC, we disallow packets to span on
@@ -3317,9 +3584,6 @@
 			 ring->queue_index);
 
 	} else {
-		ret = i40e_alloc_rx_bi(ring);
-		if (ret)
-			return ret;
 		ring->rx_buf_len = vsi->rx_buf_len;
 		if (ring->vsi->type == I40E_VSI_MAIN) {
 			ret = xdp_rxq_info_reg_mem_model(&ring->xdp_rxq,
@@ -3429,6 +3693,24 @@
 }
 
 /**
+ * i40e_calculate_vsi_rx_buf_len - Calculates buffer length
+ *
+ * @vsi: VSI to calculate rx_buf_len from
+ */
+static u16 i40e_calculate_vsi_rx_buf_len(struct i40e_vsi *vsi)
+{
+	if (!vsi->netdev || (vsi->back->flags & I40E_FLAG_LEGACY_RX))
+		return I40E_RXBUFFER_2048;
+
+#if (PAGE_SIZE < 8192)
+	if (!I40E_2K_TOO_SMALL_WITH_PADDING && vsi->netdev->mtu <= ETH_DATA_LEN)
+		return I40E_RXBUFFER_1536 - NET_IP_ALIGN;
+#endif
+
+	return PAGE_SIZE < 8192 ? I40E_RXBUFFER_3072 : I40E_RXBUFFER_2048;
+}
+
+/**
  * i40e_vsi_configure_rx - Configure the VSI for Rx
  * @vsi: the VSI being configured
  *
@@ -3439,20 +3721,14 @@
 	int err = 0;
 	u16 i;
 
-	if (!vsi->netdev || (vsi->back->flags & I40E_FLAG_LEGACY_RX)) {
-		vsi->max_frame = I40E_MAX_RXBUFFER;
-		vsi->rx_buf_len = I40E_RXBUFFER_2048;
+	vsi->max_frame = I40E_MAX_RXBUFFER;
+	vsi->rx_buf_len = i40e_calculate_vsi_rx_buf_len(vsi);
+
 #if (PAGE_SIZE < 8192)
-	} else if (!I40E_2K_TOO_SMALL_WITH_PADDING &&
-		   (vsi->netdev->mtu <= ETH_DATA_LEN)) {
+	if (vsi->netdev && !I40E_2K_TOO_SMALL_WITH_PADDING &&
+	    vsi->netdev->mtu <= ETH_DATA_LEN)
 		vsi->max_frame = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
-		vsi->rx_buf_len = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
 #endif
-	} else {
-		vsi->max_frame = I40E_MAX_RXBUFFER;
-		vsi->rx_buf_len = (PAGE_SIZE < 8192) ? I40E_RXBUFFER_3072 :
-						       I40E_RXBUFFER_2048;
-	}
 
 	/* set up individual rings */
 	for (i = 0; i < vsi->num_queue_pairs && !err; i++)
@@ -3604,6 +3880,12 @@
 		     q_vector->tx.target_itr >> 1);
 		q_vector->tx.current_itr = q_vector->tx.target_itr;
 
+		/* Set ITR for software interrupts triggered after exiting
+		 * busy-loop polling.
+		 */
+		wr32(hw, I40E_PFINT_ITRN(I40E_SW_ITR, vector - 1),
+		     I40E_ITR_20K);
+
 		wr32(hw, I40E_PFINT_RATEN(vector - 1),
 		     i40e_intrl_usec_to_reg(vsi->int_rate_limit));
 
@@ -3866,6 +4148,7 @@
 		}
 
 		/* register for affinity change notifications */
+		q_vector->irq_num = irq_num;
 		q_vector->affinity_notify.notify = i40e_irq_affinity_notify;
 		q_vector->affinity_notify.release = i40e_irq_affinity_release;
 		irq_set_affinity_notifier(irq_num, &q_vector->affinity_notify);
@@ -5059,7 +5342,7 @@
 {
 	int v, ret = 0;
 
-	for (v = 0; v < pf->hw.func_caps.num_vsis; v++) {
+	for (v = 0; v < pf->num_alloc_vsi; v++) {
 		if (pf->vsi[v]) {
 			ret = i40e_vsi_wait_queues_disabled(pf->vsi[v]);
 			if (ret)
@@ -5193,7 +5476,7 @@
 	u8 num_tc = 0;
 	struct i40e_dcbx_config *dcbcfg = &hw->local_dcbx_config;
 
-	if (pf->flags & I40E_FLAG_TC_MQPRIO)
+	if (i40e_is_tc_mqprio_enabled(pf))
 		return pf->vsi[pf->lan_vsi]->mqprio_qopt.qopt.num_tc;
 
 	/* If neither MQPRIO nor DCB is enabled, then always use single TC */
@@ -5225,7 +5508,7 @@
  **/
 static u8 i40e_pf_get_tc_map(struct i40e_pf *pf)
 {
-	if (pf->flags & I40E_FLAG_TC_MQPRIO)
+	if (i40e_is_tc_mqprio_enabled(pf))
 		return i40e_mqprio_get_enabled_tc(pf);
 
 	/* If neither MQPRIO nor DCB is enabled for this PF then just return
@@ -5257,16 +5540,16 @@
 	struct i40e_aqc_query_vsi_bw_config_resp bw_config = {0};
 	struct i40e_pf *pf = vsi->back;
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret;
 	u32 tc_bw_max;
+	int ret;
 	int i;
 
 	/* Get the VSI level BW configuration */
 	ret = i40e_aq_query_vsi_bw_config(hw, vsi->seid, &bw_config, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get PF vsi bw config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get PF vsi bw config, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EINVAL;
 	}
@@ -5276,8 +5559,8 @@
 					       NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get PF vsi ets bw config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get PF vsi ets bw config, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EINVAL;
 	}
@@ -5318,11 +5601,11 @@
 {
 	struct i40e_aqc_configure_vsi_tc_bw_data bw_data;
 	struct i40e_pf *pf = vsi->back;
-	i40e_status ret;
+	int ret;
 	int i;
 
 	/* There is no need to reset BW when mqprio mode is on.  */
-	if (pf->flags & I40E_FLAG_TC_MQPRIO)
+	if (i40e_is_tc_mqprio_enabled(pf))
 		return 0;
 	if (!vsi->mqprio_qopt.qopt.hw && !(pf->flags & I40E_FLAG_DCB_ENABLED)) {
 		ret = i40e_set_bw_limit(vsi, vsi->seid, 0);
@@ -5394,7 +5677,7 @@
 					vsi->tc_config.tc_info[i].qoffset);
 	}
 
-	if (pf->flags & I40E_FLAG_TC_MQPRIO)
+	if (i40e_is_tc_mqprio_enabled(pf))
 		return;
 
 	/* Assign UP2TC map for the VSI */
@@ -5427,6 +5710,58 @@
 }
 
 /**
+ * i40e_update_adq_vsi_queues - update queue mapping for ADq VSI
+ * @vsi: the VSI being reconfigured
+ * @vsi_offset: offset from main VF VSI
+ */
+int i40e_update_adq_vsi_queues(struct i40e_vsi *vsi, int vsi_offset)
+{
+	struct i40e_vsi_context ctxt = {};
+	struct i40e_pf *pf;
+	struct i40e_hw *hw;
+	int ret;
+
+	if (!vsi)
+		return I40E_ERR_PARAM;
+	pf = vsi->back;
+	hw = &pf->hw;
+
+	ctxt.seid = vsi->seid;
+	ctxt.pf_num = hw->pf_id;
+	ctxt.vf_num = vsi->vf_id + hw->func_caps.vf_base_id + vsi_offset;
+	ctxt.uplink_seid = vsi->uplink_seid;
+	ctxt.connection_type = I40E_AQ_VSI_CONN_TYPE_NORMAL;
+	ctxt.flags = I40E_AQ_VSI_TYPE_VF;
+	ctxt.info = vsi->info;
+
+	i40e_vsi_setup_queue_map(vsi, &ctxt, vsi->tc_config.enabled_tc,
+				 false);
+	if (vsi->reconfig_rss) {
+		vsi->rss_size = min_t(int, pf->alloc_rss_size,
+				      vsi->num_queue_pairs);
+		ret = i40e_vsi_config_rss(vsi);
+		if (ret) {
+			dev_info(&pf->pdev->dev, "Failed to reconfig rss for num_queues\n");
+			return ret;
+		}
+		vsi->reconfig_rss = false;
+	}
+
+	ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
+	if (ret) {
+		dev_info(&pf->pdev->dev, "Update vsi config failed, err %d aq_err %s\n",
+			 ret,
+			 i40e_aq_str(hw, hw->aq.asq_last_status));
+		return ret;
+	}
+	/* update the local VSI info with updated queue map */
+	i40e_vsi_update_queue_map(vsi, &ctxt);
+	vsi->info.valid_sections = 0;
+
+	return ret;
+}
+
+/**
  * i40e_vsi_config_tc - Configure VSI Tx Scheduler for given TC map
  * @vsi: VSI to be configured
  * @enabled_tc: TC bitmap
@@ -5470,8 +5805,8 @@
 						  &bw_config, NULL);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "Failed querying vsi bw info, err %s aq_err %s\n",
-				 i40e_stat_str(hw, ret),
+				 "Failed querying vsi bw info, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(hw, hw->aq.asq_last_status));
 			goto out;
 		}
@@ -5503,7 +5838,7 @@
 	ctxt.vf_num = 0;
 	ctxt.uplink_seid = vsi->uplink_seid;
 	ctxt.info = vsi->info;
-	if (vsi->back->flags & I40E_FLAG_TC_MQPRIO) {
+	if (i40e_is_tc_mqprio_enabled(pf)) {
 		ret = i40e_vsi_setup_queue_map_mqprio(vsi, &ctxt, enabled_tc);
 		if (ret)
 			goto out;
@@ -5537,8 +5872,8 @@
 	ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Update vsi tc config failed, err %s aq_err %s\n",
-			 i40e_stat_str(hw, ret),
+			 "Update vsi tc config failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(hw, hw->aq.asq_last_status));
 		goto out;
 	}
@@ -5550,8 +5885,8 @@
 	ret = i40e_vsi_get_bw_info(vsi);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Failed updating vsi bw info, err %s aq_err %s\n",
-			 i40e_stat_str(hw, ret),
+			 "Failed updating vsi bw info, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(hw, hw->aq.asq_last_status));
 		goto out;
 	}
@@ -5588,6 +5923,26 @@
 }
 
 /**
+ * i40e_bw_bytes_to_mbits - Convert max_tx_rate from bytes to mbits
+ * @vsi: Pointer to vsi structure
+ * @max_tx_rate: max TX rate in bytes to be converted into Mbits
+ *
+ * Helper function to convert units before send to set BW limit
+ **/
+static u64 i40e_bw_bytes_to_mbits(struct i40e_vsi *vsi, u64 max_tx_rate)
+{
+	if (max_tx_rate < I40E_BW_MBPS_DIVISOR) {
+		dev_warn(&vsi->back->pdev->dev,
+			 "Setting max tx rate to minimum usable value of 50Mbps.\n");
+		max_tx_rate = I40E_BW_CREDIT_DIVISOR;
+	} else {
+		do_div(max_tx_rate, I40E_BW_MBPS_DIVISOR);
+	}
+
+	return max_tx_rate;
+}
+
+/**
  * i40e_set_bw_limit - setup BW limit for Tx traffic based on max_tx_rate
  * @vsi: VSI to be configured
  * @seid: seid of the channel/VSI
@@ -5609,10 +5964,10 @@
 			max_tx_rate, seid);
 		return -EINVAL;
 	}
-	if (max_tx_rate && max_tx_rate < 50) {
+	if (max_tx_rate && max_tx_rate < I40E_BW_CREDIT_DIVISOR) {
 		dev_warn(&pf->pdev->dev,
 			 "Setting max tx rate to minimum usable value of 50Mbps.\n");
-		max_tx_rate = 50;
+		max_tx_rate = I40E_BW_CREDIT_DIVISOR;
 	}
 
 	/* Tx rate credits are in values of 50Mbps, 0 is disabled */
@@ -5622,8 +5977,8 @@
 					  I40E_MAX_BW_INACTIVE_ACCUM, NULL);
 	if (ret)
 		dev_err(&pf->pdev->dev,
-			"Failed set tx rate (%llu Mbps) for vsi->seid %u, err %s aq_err %s\n",
-			max_tx_rate, seid, i40e_stat_str(&pf->hw, ret),
+			"Failed set tx rate (%llu Mbps) for vsi->seid %u, err %d aq_err %s\n",
+			max_tx_rate, seid, ret,
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 	return ret;
 }
@@ -5698,8 +6053,8 @@
 			last_aq_status = pf->hw.aq.asq_last_status;
 			if (ret)
 				dev_info(&pf->pdev->dev,
-					 "Failed to delete cloud filter, err %s aq_err %s\n",
-					 i40e_stat_str(&pf->hw, ret),
+					 "Failed to delete cloud filter, err %d aq_err %s\n",
+					 ret,
 					 i40e_aq_str(&pf->hw, last_aq_status));
 			kfree(cfilter);
 		}
@@ -5717,24 +6072,6 @@
 }
 
 /**
- * i40e_is_any_channel - channel exist or not
- * @vsi: ptr to VSI to which channels are associated with
- *
- * Returns true or false if channel(s) exist for associated VSI or not
- **/
-static bool i40e_is_any_channel(struct i40e_vsi *vsi)
-{
-	struct i40e_channel *ch, *ch_tmp;
-
-	list_for_each_entry_safe(ch, ch_tmp, &vsi->ch_list, list) {
-		if (ch->initialized)
-			return true;
-	}
-
-	return false;
-}
-
-/**
  * i40e_get_max_queues_for_channel
  * @vsi: ptr to VSI to which channels are associated with
  *
@@ -5851,8 +6188,8 @@
 	ret = i40e_config_rss(vsi, seed, lut, vsi->rss_table_size);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Cannot set RSS lut, err %s aq_err %s\n",
-			 i40e_stat_str(hw, ret),
+			 "Cannot set RSS lut, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(hw, hw->aq.asq_last_status));
 		kfree(lut);
 		return ret;
@@ -5950,8 +6287,8 @@
 	ret = i40e_aq_add_vsi(hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "add new vsi failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "add new vsi failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw,
 				     pf->hw.aq.asq_last_status));
 		return -ENOENT;
@@ -5982,7 +6319,7 @@
 				  u8 *bw_share)
 {
 	struct i40e_aqc_configure_vsi_tc_bw_data bw_data;
-	i40e_status ret;
+	int ret;
 	int i;
 
 	memset(&bw_data, 0, sizeof(bw_data));
@@ -6018,9 +6355,9 @@
 				       struct i40e_vsi *vsi,
 				       struct i40e_channel *ch)
 {
-	i40e_status ret;
-	int i;
 	u8 bw_share[I40E_MAX_TRAFFIC_CLASS] = {0};
+	int ret;
+	int i;
 
 	/* Enable ETS TCs with equal BW Share for now across all VSIs */
 	for (i = 0; i < I40E_MAX_TRAFFIC_CLASS; i++) {
@@ -6196,8 +6533,8 @@
 					mode, NULL);
 	if (ret && hw->aq.asq_last_status != I40E_AQ_RC_ESRCH)
 		dev_err(&pf->pdev->dev,
-			"couldn't set switch config bits, err %s aq_err %s\n",
-			i40e_stat_str(hw, ret),
+			"couldn't set switch config bits, err %d aq_err %s\n",
+			ret,
 			i40e_aq_str(hw,
 				    hw->aq.asq_last_status));
 
@@ -6240,26 +6577,15 @@
 	/* By default we are in VEPA mode, if this is the first VF/VMDq
 	 * VSI to be added switch to VEB mode.
 	 */
-	if ((!(pf->flags & I40E_FLAG_VEB_MODE_ENABLED)) ||
-	    (!i40e_is_any_channel(vsi))) {
-		if (!is_power_of_2(vsi->tc_config.tc_info[0].qcount)) {
-			dev_dbg(&pf->pdev->dev,
-				"Failed to create channel. Override queues (%u) not power of 2\n",
-				vsi->tc_config.tc_info[0].qcount);
-			return -EINVAL;
-		}
 
-		if (!(pf->flags & I40E_FLAG_VEB_MODE_ENABLED)) {
-			pf->flags |= I40E_FLAG_VEB_MODE_ENABLED;
+	if (!(pf->flags & I40E_FLAG_VEB_MODE_ENABLED)) {
+		pf->flags |= I40E_FLAG_VEB_MODE_ENABLED;
 
-			if (vsi->type == I40E_VSI_MAIN) {
-				if (pf->flags & I40E_FLAG_TC_MQPRIO)
-					i40e_do_reset(pf, I40E_PF_RESET_FLAG,
-						      true);
-				else
-					i40e_do_reset_safe(pf,
-							   I40E_PF_RESET_FLAG);
-			}
+		if (vsi->type == I40E_VSI_MAIN) {
+			if (i40e_is_tc_mqprio_enabled(pf))
+				i40e_do_reset(pf, I40E_PF_RESET_FLAG, true);
+			else
+				i40e_do_reset_safe(pf, I40E_PF_RESET_FLAG);
 		}
 		/* now onwards for main VSI, number of queues will be value
 		 * of TC0's queue count
@@ -6367,6 +6693,9 @@
 			vsi->tc_seid_map[i] = ch->seid;
 		}
 	}
+
+	/* reset to reconfigure TX queue contexts */
+	i40e_do_reset(vsi->back, I40E_PF_RESET_FLAG, true);
 	return ret;
 
 err_free:
@@ -6405,8 +6734,8 @@
 						   &bw_data, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "VEB bw config failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "VEB bw config failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto out;
 	}
@@ -6415,8 +6744,8 @@
 	ret = i40e_veb_get_bw_info(veb);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Failed getting veb bw config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Failed getting veb bw config, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 	}
 
@@ -6499,8 +6828,8 @@
 	ret = i40e_aq_resume_port_tx(hw, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Resume Port Tx failed, err %s aq_err %s\n",
-			  i40e_stat_str(&pf->hw, ret),
+			 "Resume Port Tx failed, err %d aq_err %s\n",
+			  ret,
 			  i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		/* Schedule PF reset to recover */
 		set_bit(__I40E_PF_RESET_REQUESTED, pf->state);
@@ -6524,8 +6853,8 @@
 	ret = i40e_aq_suspend_port_tx(hw, pf->mac_seid, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Suspend Port Tx failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Suspend Port Tx failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		/* Schedule PF reset to recover */
 		set_bit(__I40E_PF_RESET_REQUESTED, pf->state);
@@ -6564,8 +6893,8 @@
 	ret = i40e_set_dcb_config(&pf->hw);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Set DCB Config failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Set DCB Config failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto out;
 	}
@@ -6681,8 +7010,8 @@
 		 i40e_aqc_opc_modify_switching_comp_ets, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Modify Port ETS failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Modify Port ETS failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto out;
 	}
@@ -6719,8 +7048,8 @@
 	ret = i40e_aq_dcb_updated(&pf->hw, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "DCB Updated failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "DCB Updated failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto out;
 	}
@@ -6803,8 +7132,8 @@
 		 i40e_aqc_opc_enable_switching_comp_ets, NULL);
 	if (err) {
 		dev_info(&pf->pdev->dev,
-			 "Enable Port ETS failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, err),
+			 "Enable Port ETS failed, err %d aq_err %s\n",
+			 err,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		err = -ENOENT;
 		goto out;
@@ -6883,8 +7212,8 @@
 		pf->flags |= I40E_FLAG_DISABLE_FW_LLDP;
 	} else {
 		dev_info(&pf->pdev->dev,
-			 "Query for DCB configuration failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, err),
+			 "Query for DCB configuration failed, err %d aq_err %s\n",
+			 err,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 	}
 
@@ -7102,15 +7431,15 @@
  * @pf: board private structure
  * @is_up: whether the link state should be forced up or down
  **/
-static i40e_status i40e_force_link_state(struct i40e_pf *pf, bool is_up)
+static int i40e_force_link_state(struct i40e_pf *pf, bool is_up)
 {
 	struct i40e_aq_get_phy_abilities_resp abilities;
 	struct i40e_aq_set_phy_config config = {0};
 	bool non_zero_phy_type = is_up;
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status err;
 	u64 mask;
 	u8 speed;
+	int err;
 
 	/* Card might've been put in an unstable state by other drivers
 	 * and applications, which causes incorrect speed values being
@@ -7122,8 +7451,8 @@
 					   NULL);
 	if (err) {
 		dev_err(&pf->pdev->dev,
-			"failed to get phy cap., ret =  %s last_status =  %s\n",
-			i40e_stat_str(hw, err),
+			"failed to get phy cap., ret =  %d last_status =  %s\n",
+			err,
 			i40e_aq_str(hw, hw->aq.asq_last_status));
 		return err;
 	}
@@ -7134,8 +7463,8 @@
 					   NULL);
 	if (err) {
 		dev_err(&pf->pdev->dev,
-			"failed to get phy cap., ret =  %s last_status =  %s\n",
-			i40e_stat_str(hw, err),
+			"failed to get phy cap., ret =  %d last_status =  %s\n",
+			err,
 			i40e_aq_str(hw, hw->aq.asq_last_status));
 		return err;
 	}
@@ -7179,8 +7508,8 @@
 
 	if (err) {
 		dev_err(&pf->pdev->dev,
-			"set phy config ret =  %s last_status =  %s\n",
-			i40e_stat_str(&pf->hw, err),
+			"set phy config ret =  %d last_status =  %s\n",
+			err,
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return err;
 	}
@@ -7343,11 +7672,11 @@
  * This function deletes a mac filter on the channel VSI which serves as the
  * macvlan. Returns 0 on success.
  **/
-static i40e_status i40e_del_macvlan_filter(struct i40e_hw *hw, u16 seid,
-					   const u8 *macaddr, int *aq_err)
+static int i40e_del_macvlan_filter(struct i40e_hw *hw, u16 seid,
+				   const u8 *macaddr, int *aq_err)
 {
 	struct i40e_aqc_remove_macvlan_element_data element;
-	i40e_status status;
+	int status;
 
 	memset(&element, 0, sizeof(element));
 	ether_addr_copy(element.mac_addr, macaddr);
@@ -7369,12 +7698,12 @@
  * This function adds a mac filter on the channel VSI which serves as the
  * macvlan. Returns 0 on success.
  **/
-static i40e_status i40e_add_macvlan_filter(struct i40e_hw *hw, u16 seid,
-					   const u8 *macaddr, int *aq_err)
+static int i40e_add_macvlan_filter(struct i40e_hw *hw, u16 seid,
+				   const u8 *macaddr, int *aq_err)
 {
 	struct i40e_aqc_add_macvlan_element_data element;
-	i40e_status status;
 	u16 cmd_flags = 0;
+	int status;
 
 	ether_addr_copy(element.mac_addr, macaddr);
 	element.vlan_tag = 0;
@@ -7464,42 +7793,43 @@
 static int i40e_fwd_ring_up(struct i40e_vsi *vsi, struct net_device *vdev,
 			    struct i40e_fwd_adapter *fwd)
 {
+	struct i40e_channel *ch = NULL, *ch_tmp, *iter;
 	int ret = 0, num_tc = 1,  i, aq_err;
-	struct i40e_channel *ch, *ch_tmp;
 	struct i40e_pf *pf = vsi->back;
 	struct i40e_hw *hw = &pf->hw;
 
-	if (list_empty(&vsi->macvlan_list))
-		return -EINVAL;
-
 	/* Go through the list and find an available channel */
-	list_for_each_entry_safe(ch, ch_tmp, &vsi->macvlan_list, list) {
-		if (!i40e_is_channel_macvlan(ch)) {
-			ch->fwd = fwd;
+	list_for_each_entry_safe(iter, ch_tmp, &vsi->macvlan_list, list) {
+		if (!i40e_is_channel_macvlan(iter)) {
+			iter->fwd = fwd;
 			/* record configuration for macvlan interface in vdev */
 			for (i = 0; i < num_tc; i++)
 				netdev_bind_sb_channel_queue(vsi->netdev, vdev,
 							     i,
-							     ch->num_queue_pairs,
-							     ch->base_queue);
-			for (i = 0; i < ch->num_queue_pairs; i++) {
+							     iter->num_queue_pairs,
+							     iter->base_queue);
+			for (i = 0; i < iter->num_queue_pairs; i++) {
 				struct i40e_ring *tx_ring, *rx_ring;
 				u16 pf_q;
 
-				pf_q = ch->base_queue + i;
+				pf_q = iter->base_queue + i;
 
 				/* Get to TX ring ptr */
 				tx_ring = vsi->tx_rings[pf_q];
-				tx_ring->ch = ch;
+				tx_ring->ch = iter;
 
 				/* Get the RX ring ptr */
 				rx_ring = vsi->rx_rings[pf_q];
-				rx_ring->ch = ch;
+				rx_ring->ch = iter;
 			}
+			ch = iter;
 			break;
 		}
 	}
 
+	if (!ch)
+		return -EINVAL;
+
 	/* Guarantee all rings are updated before we update the
 	 * MAC address filter.
 	 */
@@ -7519,8 +7849,8 @@
 			rx_ring->netdev = NULL;
 		}
 		dev_info(&pf->pdev->dev,
-			 "Error adding mac filter on macvlan err %s, aq_err %s\n",
-			  i40e_stat_str(hw, ret),
+			 "Error adding mac filter on macvlan err %d, aq_err %s\n",
+			  ret,
 			  i40e_aq_str(hw, aq_err));
 		netdev_err(vdev, "L2fwd offload disabled to L2 filter error\n");
 	}
@@ -7592,8 +7922,8 @@
 	ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Update vsi tc config failed, err %s aq_err %s\n",
-			 i40e_stat_str(hw, ret),
+			 "Update vsi tc config failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(hw, hw->aq.asq_last_status));
 		return ret;
 	}
@@ -7649,7 +7979,7 @@
 		netdev_info(netdev, "Macvlans are not supported when DCB is enabled\n");
 		return ERR_PTR(-EINVAL);
 	}
-	if ((pf->flags & I40E_FLAG_TC_MQPRIO)) {
+	if (i40e_is_tc_mqprio_enabled(pf)) {
 		netdev_info(netdev, "Macvlans are not supported when HW TC offload is on\n");
 		return ERR_PTR(-EINVAL);
 	}
@@ -7808,8 +8138,8 @@
 				ch->fwd = NULL;
 			} else {
 				dev_info(&pf->pdev->dev,
-					 "Error deleting mac filter on macvlan err %s, aq_err %s\n",
-					  i40e_stat_str(hw, ret),
+					 "Error deleting mac filter on macvlan err %d, aq_err %s\n",
+					  ret,
 					  i40e_aq_str(hw, aq_err));
 			}
 			break;
@@ -7902,7 +8232,7 @@
 	/* Quiesce VSI queues */
 	i40e_quiesce_vsi(vsi);
 
-	if (!hw && !(pf->flags & I40E_FLAG_TC_MQPRIO))
+	if (!hw && !i40e_is_tc_mqprio_enabled(pf))
 		i40e_remove_queue_channels(vsi);
 
 	/* Configure VSI for enabled TCs */
@@ -7912,17 +8242,25 @@
 			    vsi->seid);
 		need_reset = true;
 		goto exit;
-	} else {
-		dev_info(&vsi->back->pdev->dev,
-			 "Setup channel (id:%u) utilizing num_queues %d\n",
-			 vsi->seid, vsi->tc_config.tc_info[0].qcount);
+	} else if (enabled_tc &&
+		   (!is_power_of_2(vsi->tc_config.tc_info[0].qcount))) {
+		netdev_info(netdev,
+			    "Failed to create channel. Override queues (%u) not power of 2\n",
+			    vsi->tc_config.tc_info[0].qcount);
+		ret = -EINVAL;
+		need_reset = true;
+		goto exit;
 	}
 
-	if (pf->flags & I40E_FLAG_TC_MQPRIO) {
+	dev_info(&vsi->back->pdev->dev,
+		 "Setup channel (id:%u) utilizing num_queues %d\n",
+		 vsi->seid, vsi->tc_config.tc_info[0].qcount);
+
+	if (i40e_is_tc_mqprio_enabled(pf)) {
 		if (vsi->mqprio_qopt.max_rate[0]) {
-			u64 max_tx_rate = vsi->mqprio_qopt.max_rate[0];
+			u64 max_tx_rate = i40e_bw_bytes_to_mbits(vsi,
+						  vsi->mqprio_qopt.max_rate[0]);
 
-			do_div(max_tx_rate, I40E_BW_MBPS_DIVISOR);
 			ret = i40e_set_bw_limit(vsi, vsi->seid, max_tx_rate);
 			if (!ret) {
 				u64 credits = max_tx_rate;
@@ -8443,6 +8781,11 @@
 		return -EOPNOTSUPP;
 	}
 
+	if (!tc) {
+		dev_err(&pf->pdev->dev, "Unable to add filter because of invalid destination");
+		return -EINVAL;
+	}
+
 	if (test_bit(__I40E_RESET_RECOVERY_PENDING, pf->state) ||
 	    test_bit(__I40E_RESET_INTR_RECEIVED, pf->state))
 		return -EBUSY;
@@ -8482,9 +8825,8 @@
 		err = i40e_add_del_cloud_filter(vsi, filter, true);
 
 	if (err) {
-		dev_err(&pf->pdev->dev,
-			"Failed to add cloud filter, err %s\n",
-			i40e_stat_str(&pf->hw, err));
+		dev_err(&pf->pdev->dev, "Failed to add cloud filter, err %d\n",
+			err);
 		goto err;
 	}
 
@@ -8548,8 +8890,7 @@
 	kfree(filter);
 	if (err) {
 		dev_err(&pf->pdev->dev,
-			"Failed to delete cloud filter, err %s\n",
-			i40e_stat_str(&pf->hw, err));
+			"Failed to delete cloud filter, err %d\n", err);
 		return i40e_aq_rc_to_posix(err, pf->hw.aq.asq_last_status);
 	}
 
@@ -8669,6 +9010,27 @@
 }
 
 /**
+ * i40e_netif_set_realnum_tx_rx_queues - Update number of tx/rx queues
+ * @vsi: vsi structure
+ *
+ * This updates netdev's number of tx/rx queues
+ *
+ * Returns status of setting tx/rx queues
+ **/
+static int i40e_netif_set_realnum_tx_rx_queues(struct i40e_vsi *vsi)
+{
+	int ret;
+
+	ret = netif_set_real_num_rx_queues(vsi->netdev,
+					   vsi->num_queue_pairs);
+	if (ret)
+		return ret;
+
+	return netif_set_real_num_tx_queues(vsi->netdev,
+					    vsi->num_queue_pairs);
+}
+
+/**
  * i40e_vsi_open -
  * @vsi: the VSI to open
  *
@@ -8704,13 +9066,7 @@
 			goto err_setup_rx;
 
 		/* Notify the stack of the actual queue counts. */
-		err = netif_set_real_num_tx_queues(vsi->netdev,
-						   vsi->num_queue_pairs);
-		if (err)
-			goto err_set_queues;
-
-		err = netif_set_real_num_rx_queues(vsi->netdev,
-						   vsi->num_queue_pairs);
+		err = i40e_netif_set_realnum_tx_rx_queues(vsi);
 		if (err)
 			goto err_set_queues;
 
@@ -9096,8 +9452,8 @@
 			pf->flags &= ~I40E_FLAG_DCB_CAPABLE;
 		} else {
 			dev_info(&pf->pdev->dev,
-				 "Failed querying DCB configuration data from firmware, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "Failed querying DCB configuration data from firmware, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 		}
@@ -9545,8 +9901,8 @@
 {
 	struct i40e_vsi *vsi = pf->vsi[pf->lan_vsi];
 	u8 new_link_speed, old_link_speed;
-	i40e_status status;
 	bool new_link, old_link;
+	int status;
 #ifdef CONFIG_I40E_DCB
 	int err;
 #endif /* CONFIG_I40E_DCB */
@@ -9757,9 +10113,9 @@
 	struct i40e_arq_event_info event;
 	struct i40e_hw *hw = &pf->hw;
 	u16 pending, i = 0;
-	i40e_status ret;
 	u16 opcode;
 	u32 oldval;
+	int ret;
 	u32 val;
 
 	/* Do not run clean AQ when PF reset fails */
@@ -9923,8 +10279,8 @@
 	ret = i40e_aq_get_vsi_params(&pf->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get PF vsi config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get PF vsi config, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return;
 	}
@@ -9935,8 +10291,8 @@
 	ret = i40e_aq_update_vsi_params(&vsi->back->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "update vsi switch failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "update vsi switch failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 	}
 }
@@ -9959,8 +10315,8 @@
 	ret = i40e_aq_get_vsi_params(&pf->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get PF vsi config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get PF vsi config, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return;
 	}
@@ -9971,8 +10327,8 @@
 	ret = i40e_aq_update_vsi_params(&vsi->back->hw, &ctxt, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "update vsi switch failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "update vsi switch failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 	}
 }
@@ -10116,8 +10472,8 @@
 			buf_len = data_size;
 		} else if (pf->hw.aq.asq_last_status != I40E_AQ_RC_OK || err) {
 			dev_info(&pf->pdev->dev,
-				 "capability discovery failed, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, err),
+				 "capability discovery failed, err %d aq_err %s\n",
+				 err,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			return -ENODEV;
@@ -10238,7 +10594,7 @@
 	struct i40e_cloud_filter *cfilter;
 	struct i40e_pf *pf = vsi->back;
 	struct hlist_node *node;
-	i40e_status ret;
+	int ret;
 
 	/* Add cloud filters back if they exist */
 	hlist_for_each_entry_safe(cfilter, node, &pf->cloud_filter_list,
@@ -10254,8 +10610,8 @@
 
 		if (ret) {
 			dev_dbg(&pf->pdev->dev,
-				"Failed to rebuild cloud filter, err %s aq_err %s\n",
-				i40e_stat_str(&pf->hw, ret),
+				"Failed to rebuild cloud filter, err %d aq_err %s\n",
+				ret,
 				i40e_aq_str(&pf->hw,
 					    pf->hw.aq.asq_last_status));
 			return ret;
@@ -10273,7 +10629,7 @@
 static int i40e_rebuild_channels(struct i40e_vsi *vsi)
 {
 	struct i40e_channel *ch, *ch_tmp;
-	i40e_status ret;
+	int ret;
 
 	if (list_empty(&vsi->ch_list))
 		return 0;
@@ -10326,6 +10682,21 @@
 }
 
 /**
+ * i40e_clean_xps_state - clean xps state for every tx_ring
+ * @vsi: ptr to the VSI
+ **/
+static void i40e_clean_xps_state(struct i40e_vsi *vsi)
+{
+	int i;
+
+	if (vsi->tx_rings)
+		for (i = 0; i < vsi->num_queue_pairs; i++)
+			if (vsi->tx_rings[i])
+				clear_bit(__I40E_TX_XPS_INIT_DONE,
+					  vsi->tx_rings[i]->state);
+}
+
+/**
  * i40e_prep_for_reset - prep for the core to reset
  * @pf: board private structure
  *
@@ -10334,7 +10705,7 @@
 static void i40e_prep_for_reset(struct i40e_pf *pf)
 {
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret = 0;
+	int ret = 0;
 	u32 v;
 
 	clear_bit(__I40E_RESET_INTR_RECEIVED, pf->state);
@@ -10349,8 +10720,10 @@
 	i40e_pf_quiesce_all_vsi(pf);
 
 	for (v = 0; v < pf->num_alloc_vsi; v++) {
-		if (pf->vsi[v])
+		if (pf->vsi[v]) {
+			i40e_clean_xps_state(pf->vsi[v]);
 			pf->vsi[v]->seid = 0;
+		}
 	}
 
 	i40e_shutdown_adminq(&pf->hw);
@@ -10437,7 +10810,7 @@
 static int i40e_reset(struct i40e_pf *pf)
 {
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret;
+	int ret;
 
 	ret = i40e_pf_reset(hw);
 	if (ret) {
@@ -10459,43 +10832,35 @@
  **/
 static void i40e_rebuild(struct i40e_pf *pf, bool reinit, bool lock_acquired)
 {
-	int old_recovery_mode_bit = test_bit(__I40E_RECOVERY_MODE, pf->state);
+	const bool is_recovery_mode_reported = i40e_check_recovery_mode(pf);
 	struct i40e_vsi *vsi = pf->vsi[pf->lan_vsi];
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret;
+	int ret;
 	u32 val;
 	int v;
 
 	if (test_bit(__I40E_EMP_RESET_INTR_RECEIVED, pf->state) &&
-	    i40e_check_recovery_mode(pf)) {
+	    is_recovery_mode_reported)
 		i40e_set_ethtool_ops(pf->vsi[pf->lan_vsi]->netdev);
-	}
 
 	if (test_bit(__I40E_DOWN, pf->state) &&
-	    !test_bit(__I40E_RECOVERY_MODE, pf->state) &&
-	    !old_recovery_mode_bit)
+	    !test_bit(__I40E_RECOVERY_MODE, pf->state))
 		goto clear_recovery;
 	dev_dbg(&pf->pdev->dev, "Rebuilding internal switch\n");
 
 	/* rebuild the basics for the AdminQ, HMC, and initial HW switch */
 	ret = i40e_init_adminq(&pf->hw);
 	if (ret) {
-		dev_info(&pf->pdev->dev, "Rebuild AdminQ failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+		dev_info(&pf->pdev->dev, "Rebuild AdminQ failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto clear_recovery;
 	}
 	i40e_get_oem_version(&pf->hw);
 
-	if (test_bit(__I40E_EMP_RESET_INTR_RECEIVED, pf->state) &&
-	    ((hw->aq.fw_maj_ver == 4 && hw->aq.fw_min_ver <= 33) ||
-	     hw->aq.fw_maj_ver < 4) && hw->mac.type == I40E_MAC_XL710) {
-		/* The following delay is necessary for 4.33 firmware and older
-		 * to recover after EMP reset. 200 ms should suffice but we
-		 * put here 300 ms to be sure that FW is ready to operate
-		 * after reset.
-		 */
-		mdelay(300);
+	if (test_and_clear_bit(__I40E_EMP_RESET_INTR_RECEIVED, pf->state)) {
+		/* The following delay is necessary for firmware update. */
+		mdelay(1000);
 	}
 
 	/* re-verify the eeprom if we just had an EMP reset */
@@ -10506,13 +10871,12 @@
 	 * accordingly with regard to resources initialization
 	 * and deinitialization
 	 */
-	if (test_bit(__I40E_RECOVERY_MODE, pf->state) ||
-	    old_recovery_mode_bit) {
+	if (test_bit(__I40E_RECOVERY_MODE, pf->state)) {
 		if (i40e_get_capabilities(pf,
 					  i40e_aqc_opc_list_func_capabilities))
 			goto end_unlock;
 
-		if (test_bit(__I40E_RECOVERY_MODE, pf->state)) {
+		if (is_recovery_mode_reported) {
 			/* we're staying in recovery mode so we'll reinitialize
 			 * misc vector here
 			 */
@@ -10562,7 +10926,7 @@
 	 * unless I40E_FLAG_TC_MQPRIO was enabled or DCB
 	 * is not supported with new link speed
 	 */
-	if (pf->flags & I40E_FLAG_TC_MQPRIO) {
+	if (i40e_is_tc_mqprio_enabled(pf)) {
 		i40e_aq_set_dcb_parameters(hw, false, NULL);
 	} else {
 		if (I40E_IS_X710TL_DEVICE(hw->device_id) &&
@@ -10599,8 +10963,8 @@
 					 I40E_AQ_EVENT_MEDIA_NA |
 					 I40E_AQ_EVENT_MODULE_QUAL_FAIL), NULL);
 	if (ret)
-		dev_info(&pf->pdev->dev, "set phy mask fail, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+		dev_info(&pf->pdev->dev, "set phy mask fail, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 
 	/* Rebuild the VSIs and VEBs that existed before reset.
@@ -10657,10 +11021,10 @@
 	}
 
 	if (vsi->mqprio_qopt.max_rate[0]) {
-		u64 max_tx_rate = vsi->mqprio_qopt.max_rate[0];
+		u64 max_tx_rate = i40e_bw_bytes_to_mbits(vsi,
+						  vsi->mqprio_qopt.max_rate[0]);
 		u64 credits = 0;
 
-		do_div(max_tx_rate, I40E_BW_MBPS_DIVISOR);
 		ret = i40e_set_bw_limit(vsi, vsi->seid, max_tx_rate);
 		if (ret)
 			goto end_unlock;
@@ -10703,14 +11067,17 @@
 		msleep(75);
 		ret = i40e_aq_set_link_restart_an(&pf->hw, true, NULL);
 		if (ret)
-			dev_info(&pf->pdev->dev, "link restart failed, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+			dev_info(&pf->pdev->dev, "link restart failed, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 	}
 	/* reinit the misc interrupt */
-	if (pf->flags & I40E_FLAG_MSIX_ENABLED)
+	if (pf->flags & I40E_FLAG_MSIX_ENABLED) {
 		ret = i40e_setup_misc_vector(pf);
+		if (ret)
+			goto end_unlock;
+	}
 
 	/* Add a filter to drop all Flow control frames from any VSI from being
 	 * transmitted. By doing so we stop a malicious VF from sending out
@@ -10732,9 +11099,9 @@
 	ret = i40e_set_promiscuous(pf, pf->cur_promisc);
 	if (ret)
 		dev_warn(&pf->pdev->dev,
-			 "Failed to restore promiscuous setting: %s, err %s aq_err %s\n",
+			 "Failed to restore promiscuous setting: %s, err %d aq_err %s\n",
 			 pf->cur_promisc ? "on" : "off",
-			 i40e_stat_str(&pf->hw, ret),
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 
 	i40e_reset_all_vfs(pf, true);
@@ -10766,6 +11133,9 @@
 				   bool lock_acquired)
 {
 	int ret;
+
+	if (test_bit(__I40E_IN_REMOVE, pf->state))
+		return;
 	/* Now we wait for GRST to settle out.
 	 * We don't have to delete the VEBs or VSIs from the hw switch
 	 * because the reset will make them disappear.
@@ -11705,7 +12075,6 @@
 		return -ENOMEM;
 
 	pf->irq_pile->num_entries = vectors;
-	pf->irq_pile->search_hint = 0;
 
 	/* track first vector for misc interrupts, ignore return */
 	(void)i40e_get_lump(pf, pf->irq_pile, 1, I40E_PILE_VALID_BIT - 1);
@@ -11867,8 +12236,8 @@
 			(struct i40e_aqc_get_set_rss_key_data *)seed);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "Cannot get RSS key, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "Cannot get RSS key, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			return ret;
@@ -11881,8 +12250,8 @@
 		ret = i40e_aq_get_rss_lut(hw, vsi->id, pf_lut, lut, lut_size);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "Cannot get RSS lut, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "Cannot get RSS lut, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			return ret;
@@ -12126,6 +12495,8 @@
 
 		vsi->req_queue_pairs = queue_count;
 		i40e_prep_for_reset(pf);
+		if (test_bit(__I40E_IN_REMOVE, pf->state))
+			return pf->alloc_rss_size;
 
 		pf->alloc_rss_size = new_rss_size;
 
@@ -12155,11 +12526,11 @@
  * i40e_get_partition_bw_setting - Retrieve BW settings for this PF partition
  * @pf: board private structure
  **/
-i40e_status i40e_get_partition_bw_setting(struct i40e_pf *pf)
+int i40e_get_partition_bw_setting(struct i40e_pf *pf)
 {
-	i40e_status status;
 	bool min_valid, max_valid;
 	u32 max_bw, min_bw;
+	int status;
 
 	status = i40e_read_bw_from_alt_ram(&pf->hw, &max_bw, &min_bw,
 					   &min_valid, &max_valid);
@@ -12178,10 +12549,10 @@
  * i40e_set_partition_bw_setting - Set BW settings for this PF partition
  * @pf: board private structure
  **/
-i40e_status i40e_set_partition_bw_setting(struct i40e_pf *pf)
+int i40e_set_partition_bw_setting(struct i40e_pf *pf)
 {
 	struct i40e_aqc_configure_partition_bw_data bw_data;
-	i40e_status status;
+	int status;
 
 	memset(&bw_data, 0, sizeof(bw_data));
 
@@ -12200,12 +12571,12 @@
  * i40e_commit_partition_bw_setting - Commit BW settings for this PF partition
  * @pf: board private structure
  **/
-i40e_status i40e_commit_partition_bw_setting(struct i40e_pf *pf)
+int i40e_commit_partition_bw_setting(struct i40e_pf *pf)
 {
 	/* Commit temporary BW setting to permanent NVM image */
 	enum i40e_admin_queue_err last_aq_status;
-	i40e_status ret;
 	u16 nvm_word;
+	int ret;
 
 	if (pf->hw.partition_id != 1) {
 		dev_info(&pf->pdev->dev,
@@ -12220,8 +12591,8 @@
 	last_aq_status = pf->hw.aq.asq_last_status;
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Cannot acquire NVM for read access, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Cannot acquire NVM for read access, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, last_aq_status));
 		goto bw_commit_out;
 	}
@@ -12237,8 +12608,8 @@
 	last_aq_status = pf->hw.aq.asq_last_status;
 	i40e_release_nvm(&pf->hw);
 	if (ret) {
-		dev_info(&pf->pdev->dev, "NVM read error, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+		dev_info(&pf->pdev->dev, "NVM read error, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, last_aq_status));
 		goto bw_commit_out;
 	}
@@ -12251,8 +12622,8 @@
 	last_aq_status = pf->hw.aq.asq_last_status;
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "Cannot acquire NVM for write access, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "Cannot acquire NVM for write access, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, last_aq_status));
 		goto bw_commit_out;
 	}
@@ -12271,8 +12642,8 @@
 	i40e_release_nvm(&pf->hw);
 	if (ret)
 		dev_info(&pf->pdev->dev,
-			 "BW settings NOT SAVED, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "BW settings NOT SAVED, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, last_aq_status));
 bw_commit_out:
 
@@ -12293,7 +12664,7 @@
 #define I40E_LINK_BEHAVIOR_WORD_LENGTH		0x1
 #define I40E_LINK_BEHAVIOR_OS_FORCED_ENABLED	BIT(0)
 #define I40E_LINK_BEHAVIOR_PORT_BIT_LENGTH	4
-	i40e_status read_status = I40E_SUCCESS;
+	int read_status = I40E_SUCCESS;
 	u16 sr_emp_sr_settings_ptr = 0;
 	u16 features_enable = 0;
 	u16 link_behavior = 0;
@@ -12326,8 +12697,8 @@
 
 err_nvm:
 	dev_warn(&pf->pdev->dev,
-		 "total-port-shutdown feature is off due to read nvm error: %s\n",
-		 i40e_stat_str(&pf->hw, read_status));
+		 "total-port-shutdown feature is off due to read nvm error: %d\n",
+		 read_status);
 	return ret;
 }
 
@@ -12508,7 +12879,6 @@
 		goto sw_init_done;
 	}
 	pf->qp_pile->num_entries = pf->hw.func_caps.num_tx_qp;
-	pf->qp_pile->search_hint = 0;
 
 	pf->tx_timeout_recovery_level = 1;
 
@@ -12646,7 +13016,7 @@
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_hw *hw = &np->vsi->back->hw;
 	u8 type, filter_index;
-	i40e_status ret;
+	int ret;
 
 	type = ti->type == UDP_TUNNEL_TYPE_VXLAN ? I40E_AQC_TUNNEL_TYPE_VXLAN :
 						   I40E_AQC_TUNNEL_TYPE_NGE;
@@ -12654,8 +13024,8 @@
 	ret = i40e_aq_add_udp_tunnel(hw, ntohs(ti->port), type, &filter_index,
 				     NULL);
 	if (ret) {
-		netdev_info(netdev, "add UDP port failed, err %s aq_err %s\n",
-			    i40e_stat_str(hw, ret),
+		netdev_info(netdev, "add UDP port failed, err %d aq_err %s\n",
+			    ret,
 			    i40e_aq_str(hw, hw->aq.asq_last_status));
 		return -EIO;
 	}
@@ -12670,12 +13040,12 @@
 {
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_hw *hw = &np->vsi->back->hw;
-	i40e_status ret;
+	int ret;
 
 	ret = i40e_aq_del_udp_tunnel(hw, ti->hw_priv, NULL);
 	if (ret) {
-		netdev_info(netdev, "delete UDP port failed, err %s aq_err %s\n",
-			    i40e_stat_str(hw, ret),
+		netdev_info(netdev, "delete UDP port failed, err %d aq_err %s\n",
+			    ret,
 			    i40e_aq_str(hw, hw->aq.asq_last_status));
 		return -EIO;
 	}
@@ -12788,6 +13158,8 @@
 	}
 
 	br_spec = nlmsg_find_attr(nlh, sizeof(struct ifinfomsg), IFLA_AF_SPEC);
+	if (!br_spec)
+		return -EINVAL;
 
 	nla_for_each_nested(attr, br_spec, rem) {
 		__u16 mode;
@@ -12941,15 +13313,18 @@
 	bool need_reset;
 	int i;
 
+	/* VSI shall be deleted in a moment, block loading new programs */
+	if (prog && test_bit(__I40E_IN_REMOVE, pf->state))
+		return -EINVAL;
+
 	/* Don't allow frames that span over multiple buffers */
-	if (frame_size > vsi->rx_buf_len) {
+	if (frame_size > i40e_calculate_vsi_rx_buf_len(vsi)) {
 		NL_SET_ERR_MSG_MOD(extack, "MTU too large to enable XDP");
 		return -EINVAL;
 	}
 
 	/* When turning XDP on->off/off->on we reset and rebuild the rings. */
 	need_reset = (i40e_enabled_xdp_vsi(vsi) != !!prog);
-
 	if (need_reset)
 		i40e_prep_for_reset(pf);
 
@@ -12962,6 +13337,14 @@
 		i40e_reset_and_rebuild(pf, true, true);
 	}
 
+	if (!i40e_enabled_xdp_vsi(vsi) && prog) {
+		if (i40e_realloc_rx_bi_zc(vsi, true))
+			return -ENOMEM;
+	} else if (i40e_enabled_xdp_vsi(vsi) && !prog) {
+		if (i40e_realloc_rx_bi_zc(vsi, false))
+			return -ENOMEM;
+	}
+
 	for (i = 0; i < vsi->num_queue_pairs; i++)
 		WRITE_ONCE(vsi->rx_rings[i]->xdp_prog, vsi->xdp_prog);
 
@@ -13193,8 +13576,9 @@
 		return err;
 
 	i40e_queue_pair_disable_irq(vsi, queue_pair);
-	err = i40e_queue_pair_toggle_rings(vsi, queue_pair, false /* off */);
 	i40e_queue_pair_toggle_napi(vsi, queue_pair, false /* off */);
+	err = i40e_queue_pair_toggle_rings(vsi, queue_pair, false /* off */);
+	i40e_clean_rx_ring(vsi->rx_rings[queue_pair]);
 	i40e_queue_pair_clean_rings(vsi, queue_pair);
 	i40e_queue_pair_reset_stats(vsi, queue_pair);
 
@@ -13425,7 +13809,7 @@
 	i40e_add_mac_filter(vsi, broadcast);
 	spin_unlock_bh(&vsi->mac_filter_hash_lock);
 
-	ether_addr_copy(netdev->dev_addr, mac_addr);
+	eth_hw_addr_set(netdev, mac_addr);
 	ether_addr_copy(netdev->perm_addr, mac_addr);
 
 	/* i40iw_net_event() reads 16 bytes from neigh->primary_key */
@@ -13531,8 +13915,8 @@
 		ctxt.flags = I40E_AQ_VSI_TYPE_PF;
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "couldn't get PF vsi config, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "couldn't get PF vsi config, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			return -ENOENT;
@@ -13561,8 +13945,8 @@
 			ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
 			if (ret) {
 				dev_info(&pf->pdev->dev,
-					 "update vsi failed, err %s aq_err %s\n",
-					 i40e_stat_str(&pf->hw, ret),
+					 "update vsi failed, err %d aq_err %s\n",
+					 ret,
 					 i40e_aq_str(&pf->hw,
 						     pf->hw.aq.asq_last_status));
 				ret = -ENOENT;
@@ -13581,8 +13965,8 @@
 			ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
 			if (ret) {
 				dev_info(&pf->pdev->dev,
-					 "update vsi failed, err %s aq_err %s\n",
-					 i40e_stat_str(&pf->hw, ret),
+					 "update vsi failed, err %d aq_err %s\n",
+					 ret,
 					 i40e_aq_str(&pf->hw,
 						    pf->hw.aq.asq_last_status));
 				ret = -ENOENT;
@@ -13604,9 +13988,9 @@
 				 * message and continue
 				 */
 				dev_info(&pf->pdev->dev,
-					 "failed to configure TCs for main VSI tc_map 0x%08x, err %s aq_err %s\n",
+					 "failed to configure TCs for main VSI tc_map 0x%08x, err %d aq_err %s\n",
 					 enabled_tc,
-					 i40e_stat_str(&pf->hw, ret),
+					 ret,
 					 i40e_aq_str(&pf->hw,
 						    pf->hw.aq.asq_last_status));
 			}
@@ -13700,8 +14084,8 @@
 		ret = i40e_aq_add_vsi(hw, &ctxt, NULL);
 		if (ret) {
 			dev_info(&vsi->back->pdev->dev,
-				 "add vsi failed, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "add vsi failed, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			ret = -ENOENT;
@@ -13713,15 +14097,15 @@
 		vsi->id = ctxt.vsi_number;
 	}
 
-	vsi->active_filters = 0;
-	clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state);
 	spin_lock_bh(&vsi->mac_filter_hash_lock);
+	vsi->active_filters = 0;
 	/* If macvlan filters already exist, force them to get loaded */
 	hash_for_each_safe(vsi->mac_filter_hash, bkt, h, f, hlist) {
 		f->state = I40E_FILTER_NEW;
 		f_count++;
 	}
 	spin_unlock_bh(&vsi->mac_filter_hash_lock);
+	clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state);
 
 	if (f_count) {
 		vsi->flags |= I40E_VSI_FLAG_FILTER_CHANGED;
@@ -13732,8 +14116,8 @@
 	ret = i40e_vsi_get_bw_info(vsi);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get vsi bw info, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get vsi bw info, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		/* VSI is already added so not tearing that up */
 		ret = 0;
@@ -13771,7 +14155,7 @@
 		dev_info(&pf->pdev->dev, "Can't remove PF VSI\n");
 		return -ENODEV;
 	}
-
+	set_bit(__I40E_VSI_RELEASING, vsi->state);
 	uplink_seid = vsi->uplink_seid;
 	if (vsi->type != I40E_VSI_SRIOV) {
 		if (vsi->netdev_registered) {
@@ -14103,6 +14487,9 @@
 		ret = i40e_config_netdev(vsi);
 		if (ret)
 			goto err_netdev;
+		ret = i40e_netif_set_realnum_tx_rx_queues(vsi);
+		if (ret)
+			goto err_netdev;
 		ret = register_netdev(vsi->netdev);
 		if (ret)
 			goto err_netdev;
@@ -14176,8 +14563,8 @@
 						  &bw_data, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "query veb bw config failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "query veb bw config failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, hw->aq.asq_last_status));
 		goto out;
 	}
@@ -14186,8 +14573,8 @@
 						   &ets_data, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "query veb bw ets config failed, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "query veb bw ets config failed, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, hw->aq.asq_last_status));
 		goto out;
 	}
@@ -14383,8 +14770,8 @@
 	/* get a VEB from the hardware */
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't add VEB, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't add VEB, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EPERM;
 	}
@@ -14394,16 +14781,16 @@
 					 &veb->stats_idx, NULL, NULL, NULL);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get VEB statistics idx, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get VEB statistics idx, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return -EPERM;
 	}
 	ret = i40e_veb_get_bw_info(veb);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't get VEB bw info, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't get VEB bw info, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		i40e_aq_delete_element(&pf->hw, veb->seid, NULL);
 		return -ENOENT;
@@ -14613,8 +15000,8 @@
 						&next_seid, NULL);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-				 "get switch config failed err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "get switch config failed err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			kfree(aq_buf);
@@ -14659,8 +15046,8 @@
 	ret = i40e_fetch_switch_configuration(pf, false);
 	if (ret) {
 		dev_info(&pf->pdev->dev,
-			 "couldn't fetch switch config, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, ret),
+			 "couldn't fetch switch config, err %d aq_err %s\n",
+			 ret,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		return ret;
 	}
@@ -14686,8 +15073,8 @@
 						NULL);
 		if (ret && pf->hw.aq.asq_last_status != I40E_AQ_RC_ESRCH) {
 			dev_info(&pf->pdev->dev,
-				 "couldn't set switch config bits, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, ret),
+				 "couldn't set switch config bits, err %d aq_err %s\n",
+				 ret,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 			/* not a fatal problem, just keep going */
@@ -15024,13 +15411,12 @@
  *
  * Return 0 on success, negative on failure.
  **/
-static i40e_status i40e_pf_loop_reset(struct i40e_pf *pf)
+static int i40e_pf_loop_reset(struct i40e_pf *pf)
 {
 	/* wait max 10 seconds for PF reset to succeed */
 	const unsigned long time_end = jiffies + 10 * HZ;
-
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret;
+	int ret;
 
 	ret = i40e_pf_reset(hw);
 	while (ret != I40E_SUCCESS && time_before(jiffies, time_end)) {
@@ -15076,9 +15462,9 @@
  * Return 0 if NIC is healthy or negative value when there are issues
  * with resets
  **/
-static i40e_status i40e_handle_resets(struct i40e_pf *pf)
+static int i40e_handle_resets(struct i40e_pf *pf)
 {
-	const i40e_status pfr = i40e_pf_loop_reset(pf);
+	const int pfr = i40e_pf_loop_reset(pf);
 	const bool is_empr = i40e_check_fw_empr(pf);
 
 	if (is_empr || pfr != I40E_SUCCESS)
@@ -15103,6 +15489,7 @@
 	int err;
 	int v_idx;
 
+	pci_set_drvdata(pf->pdev, pf);
 	pci_save_state(pf->pdev);
 
 	/* set up periodic task facility */
@@ -15216,13 +15603,15 @@
 	struct i40e_aq_get_phy_abilities_resp abilities;
 #ifdef CONFIG_I40E_DCB
 	enum i40e_get_fw_lldp_status_resp lldp_status;
-	i40e_status status;
 #endif /* CONFIG_I40E_DCB */
 	struct i40e_pf *pf;
 	struct i40e_hw *hw;
 	static u16 pfs_found;
 	u16 wol_nvm_bits;
 	u16 link_status;
+#ifdef CONFIG_I40E_DCB
+	int status;
+#endif /* CONFIG_I40E_DCB */
 	int err;
 	u32 val;
 	u32 i;
@@ -15403,8 +15792,8 @@
 
 	if (hw->aq.api_maj_ver == I40E_FW_API_VERSION_MAJOR &&
 	    hw->aq.api_min_ver > I40E_FW_MINOR_VERSION(hw))
-		dev_info(&pdev->dev,
-			 "The driver for the device detected a newer version of the NVM image v%u.%u than expected v%u.%u. Please install the most recent version of the network driver.\n",
+		dev_dbg(&pdev->dev,
+			"The driver for the device detected a newer version of the NVM image v%u.%u than v%u.%u.\n",
 			 hw->aq.api_maj_ver,
 			 hw->aq.api_min_ver,
 			 I40E_FW_API_VERSION_MAJOR,
@@ -15594,8 +15983,8 @@
 					 I40E_AQ_EVENT_MEDIA_NA |
 					 I40E_AQ_EVENT_MODULE_QUAL_FAIL), NULL);
 	if (err)
-		dev_info(&pf->pdev->dev, "set phy mask fail, err %s aq_err %s\n",
-			 i40e_stat_str(&pf->hw, err),
+		dev_info(&pf->pdev->dev, "set phy mask fail, err %d aq_err %s\n",
+			 err,
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 
 	/* Reconfigure hardware for allowing smaller MSS in the case
@@ -15613,8 +16002,8 @@
 		msleep(75);
 		err = i40e_aq_set_link_restart_an(&pf->hw, true, NULL);
 		if (err)
-			dev_info(&pf->pdev->dev, "link restart failed, err %s aq_err %s\n",
-				 i40e_stat_str(&pf->hw, err),
+			dev_info(&pf->pdev->dev, "link restart failed, err %d aq_err %s\n",
+				 err,
 				 i40e_aq_str(&pf->hw,
 					     pf->hw.aq.asq_last_status));
 	}
@@ -15746,8 +16135,8 @@
 	/* get the requested speeds from the fw */
 	err = i40e_aq_get_phy_capabilities(hw, false, false, &abilities, NULL);
 	if (err)
-		dev_dbg(&pf->pdev->dev, "get requested speeds ret =  %s last_status =  %s\n",
-			i40e_stat_str(&pf->hw, err),
+		dev_dbg(&pf->pdev->dev, "get requested speeds ret =  %d last_status =  %s\n",
+			err,
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 	pf->hw.phy.link_info.requested_speeds = abilities.link_speed;
 
@@ -15757,8 +16146,8 @@
 	/* get the supported phy types from the fw */
 	err = i40e_aq_get_phy_capabilities(hw, false, true, &abilities, NULL);
 	if (err)
-		dev_dbg(&pf->pdev->dev, "get supported phy types ret =  %s last_status =  %s\n",
-			i40e_stat_str(&pf->hw, err),
+		dev_dbg(&pf->pdev->dev, "get supported phy types ret =  %d last_status =  %s\n",
+			err,
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 
 	/* make sure the MFS hasn't been set lower than the default */
@@ -15766,8 +16155,8 @@
 	val = (rd32(&pf->hw, I40E_PRTGL_SAH) &
 	       I40E_PRTGL_SAH_MFS_MASK) >> I40E_PRTGL_SAH_MFS_SHIFT;
 	if (val < MAX_FRAME_SIZE_DEFAULT)
-		dev_warn(&pdev->dev, "MFS for port %x has been set below the default: %x\n",
-			 i, val);
+		dev_warn(&pdev->dev, "MFS for port %x (%d) has been set below the default (%d)\n",
+			 pf->hw.port, val, MAX_FRAME_SIZE_DEFAULT);
 
 	/* Add a filter to drop all Flow control frames from any VSI from being
 	 * transmitted. By doing so we stop a malicious VF from sending out
@@ -15829,7 +16218,7 @@
 {
 	struct i40e_pf *pf = pci_get_drvdata(pdev);
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret_code;
+	int ret_code;
 	int i;
 
 	i40e_dbg_pf_exit(pf);
@@ -15840,8 +16229,13 @@
 	i40e_write_rx_ctl(hw, I40E_PFQF_HENA(0), 0);
 	i40e_write_rx_ctl(hw, I40E_PFQF_HENA(1), 0);
 
-	while (test_bit(__I40E_RESET_RECOVERY_PENDING, pf->state))
+	/* Grab __I40E_RESET_RECOVERY_PENDING and set __I40E_IN_REMOVE
+	 * flags, once they are set, i40e_rebuild should not be called as
+	 * i40e_prep_for_reset always returns early.
+	 */
+	while (test_and_set_bit(__I40E_RESET_RECOVERY_PENDING, pf->state))
 		usleep_range(1000, 2000);
+	set_bit(__I40E_IN_REMOVE, pf->state);
 
 	if (pf->flags & I40E_FLAG_SRIOV_ENABLED) {
 		set_bit(__I40E_VF_RESETS_DISABLED, pf->state);
@@ -15888,11 +16282,15 @@
 			i40e_switch_branch_release(pf->veb[i]);
 	}
 
-	/* Now we can shutdown the PF's VSI, just before we kill
+	/* Now we can shutdown the PF's VSIs, just before we kill
 	 * adminq and hmc.
 	 */
-	if (pf->vsi[pf->lan_vsi])
-		i40e_vsi_release(pf->vsi[pf->lan_vsi]);
+	for (i = pf->num_alloc_vsi; i--;)
+		if (pf->vsi[i]) {
+			i40e_vsi_close(pf->vsi[i]);
+			i40e_vsi_release(pf->vsi[i]);
+			pf->vsi[i] = NULL;
+		}
 
 	i40e_cloud_filter_exit(pf);
 
@@ -16040,7 +16438,13 @@
 {
 	struct i40e_pf *pf = pci_get_drvdata(pdev);
 
+	if (test_bit(__I40E_IN_REMOVE, pf->state))
+		return;
+
 	i40e_reset_and_rebuild(pf, false, false);
+#ifdef CONFIG_PCI_IOV
+	i40e_restore_all_vfs_msi_state(pdev);
+#endif /* CONFIG_PCI_IOV */
 }
 
 /**
@@ -16069,9 +16473,9 @@
 static void i40e_enable_mc_magic_wake(struct i40e_pf *pf)
 {
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status ret;
 	u8 mac_addr[6];
 	u16 flags = 0;
+	int ret;
 
 	/* Get current MAC address in case it's an LAA */
 	if (pf->vsi[pf->lan_vsi] && pf->vsi[pf->lan_vsi]->netdev) {
@@ -16282,6 +16686,8 @@
  **/
 static int __init i40e_init_module(void)
 {
+	int err;
+
 	pr_info("%s: %s\n", i40e_driver_name, i40e_driver_string);
 	pr_info("%s: %s\n", i40e_driver_name, i40e_copyright);
 
@@ -16292,14 +16698,21 @@
 	 * since we need to be able to guarantee forward progress even under
 	 * memory pressure.
 	 */
-	i40e_wq = alloc_workqueue("%s", WQ_MEM_RECLAIM, 0, i40e_driver_name);
+	i40e_wq = alloc_workqueue("%s", 0, 0, i40e_driver_name);
 	if (!i40e_wq) {
 		pr_err("%s: Failed to create workqueue\n", i40e_driver_name);
 		return -ENOMEM;
 	}
 
 	i40e_dbg_init();
-	return pci_register_driver(&i40e_driver);
+	err = pci_register_driver(&i40e_driver);
+	if (err) {
+		destroy_workqueue(i40e_wq);
+		i40e_dbg_exit();
+		return err;
+	}
+
+	return 0;
 }
 module_init(i40e_init_module);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_nvm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_nvm.c
@@ -13,10 +13,10 @@
  * in this file) as an equivalent of the FLASH part mapped into the SR.
  * We are accessing FLASH always thru the Shadow RAM.
  **/
-i40e_status i40e_init_nvm(struct i40e_hw *hw)
+int i40e_init_nvm(struct i40e_hw *hw)
 {
 	struct i40e_nvm_info *nvm = &hw->nvm;
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 	u32 fla, gens;
 	u8 sr_size;
 
@@ -52,12 +52,12 @@
  * This function will request NVM ownership for reading
  * via the proper Admin Command.
  **/
-i40e_status i40e_acquire_nvm(struct i40e_hw *hw,
-				       enum i40e_aq_resource_access_type access)
+int i40e_acquire_nvm(struct i40e_hw *hw,
+		     enum i40e_aq_resource_access_type access)
 {
-	i40e_status ret_code = 0;
 	u64 gtime, timeout;
 	u64 time_left = 0;
+	int ret_code = 0;
 
 	if (hw->nvm.blank_nvm_mode)
 		goto i40e_i40e_acquire_nvm_exit;
@@ -111,7 +111,7 @@
  **/
 void i40e_release_nvm(struct i40e_hw *hw)
 {
-	i40e_status ret_code = I40E_SUCCESS;
+	int ret_code = I40E_SUCCESS;
 	u32 total_delay = 0;
 
 	if (hw->nvm.blank_nvm_mode)
@@ -138,9 +138,9 @@
  *
  * Polls the SRCTL Shadow RAM register done bit.
  **/
-static i40e_status i40e_poll_sr_srctl_done_bit(struct i40e_hw *hw)
+static int i40e_poll_sr_srctl_done_bit(struct i40e_hw *hw)
 {
-	i40e_status ret_code = I40E_ERR_TIMEOUT;
+	int ret_code = I40E_ERR_TIMEOUT;
 	u32 srctl, wait_cnt;
 
 	/* Poll the I40E_GLNVM_SRCTL until the done bit is set */
@@ -165,10 +165,10 @@
  *
  * Reads one 16 bit word from the Shadow RAM using the GLNVM_SRCTL register.
  **/
-static i40e_status i40e_read_nvm_word_srctl(struct i40e_hw *hw, u16 offset,
-					    u16 *data)
+static int i40e_read_nvm_word_srctl(struct i40e_hw *hw, u16 offset,
+				    u16 *data)
 {
-	i40e_status ret_code = I40E_ERR_TIMEOUT;
+	int ret_code = I40E_ERR_TIMEOUT;
 	u32 sr_reg;
 
 	if (offset >= hw->nvm.sr_size) {
@@ -210,19 +210,19 @@
  * @hw: pointer to the HW structure.
  * @module_pointer: module pointer location in words from the NVM beginning
  * @offset: offset in words from module start
- * @words: number of words to write
- * @data: buffer with words to write to the Shadow RAM
+ * @words: number of words to read
+ * @data: buffer with words to read to the Shadow RAM
  * @last_command: tells the AdminQ that this is the last command
  *
- * Writes a 16 bit words buffer to the Shadow RAM using the admin command.
+ * Reads a 16 bit words buffer to the Shadow RAM using the admin command.
  **/
-static i40e_status i40e_read_nvm_aq(struct i40e_hw *hw,
-				    u8 module_pointer, u32 offset,
-				    u16 words, void *data,
-				    bool last_command)
+static int i40e_read_nvm_aq(struct i40e_hw *hw,
+			    u8 module_pointer, u32 offset,
+			    u16 words, void *data,
+			    bool last_command)
 {
-	i40e_status ret_code = I40E_ERR_NVM;
 	struct i40e_asq_cmd_details cmd_details;
+	int ret_code = I40E_ERR_NVM;
 
 	memset(&cmd_details, 0, sizeof(cmd_details));
 	cmd_details.wb_desc = &hw->nvm_wb_desc;
@@ -234,18 +234,18 @@
 	 */
 	if ((offset + words) > hw->nvm.sr_size)
 		i40e_debug(hw, I40E_DEBUG_NVM,
-			   "NVM write error: offset %d beyond Shadow RAM limit %d\n",
+			   "NVM read error: offset %d beyond Shadow RAM limit %d\n",
 			   (offset + words), hw->nvm.sr_size);
 	else if (words > I40E_SR_SECTOR_SIZE_IN_WORDS)
-		/* We can write only up to 4KB (one sector), in one AQ write */
+		/* We can read only up to 4KB (one sector), in one AQ write */
 		i40e_debug(hw, I40E_DEBUG_NVM,
-			   "NVM write fail error: tried to write %d words, limit is %d.\n",
+			   "NVM read fail error: tried to read %d words, limit is %d.\n",
 			   words, I40E_SR_SECTOR_SIZE_IN_WORDS);
 	else if (((offset + (words - 1)) / I40E_SR_SECTOR_SIZE_IN_WORDS)
 		 != (offset / I40E_SR_SECTOR_SIZE_IN_WORDS))
-		/* A single write cannot spread over two sectors */
+		/* A single read cannot spread over two sectors */
 		i40e_debug(hw, I40E_DEBUG_NVM,
-			   "NVM write error: cannot spread over two sectors in a single write offset=%d words=%d\n",
+			   "NVM read error: cannot spread over two sectors in a single read offset=%d words=%d\n",
 			   offset, words);
 	else
 		ret_code = i40e_aq_read_nvm(hw, module_pointer,
@@ -264,10 +264,10 @@
  *
  * Reads one 16 bit word from the Shadow RAM using the AdminQ
  **/
-static i40e_status i40e_read_nvm_word_aq(struct i40e_hw *hw, u16 offset,
-					 u16 *data)
+static int i40e_read_nvm_word_aq(struct i40e_hw *hw, u16 offset,
+				 u16 *data)
 {
-	i40e_status ret_code = I40E_ERR_TIMEOUT;
+	int ret_code = I40E_ERR_TIMEOUT;
 
 	ret_code = i40e_read_nvm_aq(hw, 0x0, offset, 1, data, true);
 	*data = le16_to_cpu(*(__le16 *)data);
@@ -286,8 +286,8 @@
  * Do not use this function except in cases where the nvm lock is already
  * taken via i40e_acquire_nvm().
  **/
-static i40e_status __i40e_read_nvm_word(struct i40e_hw *hw,
-					u16 offset, u16 *data)
+static int __i40e_read_nvm_word(struct i40e_hw *hw,
+				u16 offset, u16 *data)
 {
 	if (hw->flags & I40E_HW_FLAG_AQ_SRCTL_ACCESS_ENABLE)
 		return i40e_read_nvm_word_aq(hw, offset, data);
@@ -303,10 +303,10 @@
  *
  * Reads one 16 bit word from the Shadow RAM.
  **/
-i40e_status i40e_read_nvm_word(struct i40e_hw *hw, u16 offset,
-			       u16 *data)
+int i40e_read_nvm_word(struct i40e_hw *hw, u16 offset,
+		       u16 *data)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	if (hw->flags & I40E_HW_FLAG_NVM_READ_REQUIRES_LOCK)
 		ret_code = i40e_acquire_nvm(hw, I40E_RESOURCE_READ);
@@ -330,17 +330,17 @@
  * @words_data_size: Words to read from NVM
  * @data_ptr: Pointer to memory location where resulting buffer will be stored
  **/
-enum i40e_status_code i40e_read_nvm_module_data(struct i40e_hw *hw,
-						u8 module_ptr,
-						u16 module_offset,
-						u16 data_offset,
-						u16 words_data_size,
-						u16 *data_ptr)
+int i40e_read_nvm_module_data(struct i40e_hw *hw,
+			      u8 module_ptr,
+			      u16 module_offset,
+			      u16 data_offset,
+			      u16 words_data_size,
+			      u16 *data_ptr)
 {
-	i40e_status status;
 	u16 specific_ptr = 0;
 	u16 ptr_value = 0;
 	u32 offset = 0;
+	int status;
 
 	if (module_ptr != 0) {
 		status = i40e_read_nvm_word(hw, module_ptr, &ptr_value);
@@ -406,10 +406,10 @@
  * method. The buffer read is preceded by the NVM ownership take
  * and followed by the release.
  **/
-static i40e_status i40e_read_nvm_buffer_srctl(struct i40e_hw *hw, u16 offset,
-					      u16 *words, u16 *data)
+static int i40e_read_nvm_buffer_srctl(struct i40e_hw *hw, u16 offset,
+				      u16 *words, u16 *data)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 	u16 index, word;
 
 	/* Loop thru the selected region */
@@ -437,13 +437,13 @@
  * method. The buffer read is preceded by the NVM ownership take
  * and followed by the release.
  **/
-static i40e_status i40e_read_nvm_buffer_aq(struct i40e_hw *hw, u16 offset,
-					   u16 *words, u16 *data)
+static int i40e_read_nvm_buffer_aq(struct i40e_hw *hw, u16 offset,
+				   u16 *words, u16 *data)
 {
-	i40e_status ret_code;
-	u16 read_size;
 	bool last_cmd = false;
 	u16 words_read = 0;
+	u16 read_size;
+	int ret_code;
 	u16 i = 0;
 
 	do {
@@ -493,9 +493,9 @@
  * Reads 16 bit words (data buffer) from the SR using the i40e_read_nvm_srrd()
  * method.
  **/
-static i40e_status __i40e_read_nvm_buffer(struct i40e_hw *hw,
-					  u16 offset, u16 *words,
-					  u16 *data)
+static int __i40e_read_nvm_buffer(struct i40e_hw *hw,
+				  u16 offset, u16 *words,
+				  u16 *data)
 {
 	if (hw->flags & I40E_HW_FLAG_AQ_SRCTL_ACCESS_ENABLE)
 		return i40e_read_nvm_buffer_aq(hw, offset, words, data);
@@ -514,10 +514,10 @@
  * method. The buffer read is preceded by the NVM ownership take
  * and followed by the release.
  **/
-i40e_status i40e_read_nvm_buffer(struct i40e_hw *hw, u16 offset,
-				 u16 *words, u16 *data)
+int i40e_read_nvm_buffer(struct i40e_hw *hw, u16 offset,
+			 u16 *words, u16 *data)
 {
-	i40e_status ret_code = 0;
+	int ret_code = 0;
 
 	if (hw->flags & I40E_HW_FLAG_AQ_SRCTL_ACCESS_ENABLE) {
 		ret_code = i40e_acquire_nvm(hw, I40E_RESOURCE_READ);
@@ -544,12 +544,12 @@
  *
  * Writes a 16 bit words buffer to the Shadow RAM using the admin command.
  **/
-static i40e_status i40e_write_nvm_aq(struct i40e_hw *hw, u8 module_pointer,
-				     u32 offset, u16 words, void *data,
-				     bool last_command)
+static int i40e_write_nvm_aq(struct i40e_hw *hw, u8 module_pointer,
+			     u32 offset, u16 words, void *data,
+			     bool last_command)
 {
-	i40e_status ret_code = I40E_ERR_NVM;
 	struct i40e_asq_cmd_details cmd_details;
+	int ret_code = I40E_ERR_NVM;
 
 	memset(&cmd_details, 0, sizeof(cmd_details));
 	cmd_details.wb_desc = &hw->nvm_wb_desc;
@@ -594,14 +594,14 @@
  * is customer specific and unknown. Therefore, this function skips all maximum
  * possible size of VPD (1kB).
  **/
-static i40e_status i40e_calc_nvm_checksum(struct i40e_hw *hw,
-						    u16 *checksum)
+static int i40e_calc_nvm_checksum(struct i40e_hw *hw,
+				  u16 *checksum)
 {
-	i40e_status ret_code;
 	struct i40e_virt_mem vmem;
 	u16 pcie_alt_module = 0;
 	u16 checksum_local = 0;
 	u16 vpd_module = 0;
+	int ret_code;
 	u16 *data;
 	u16 i = 0;
 
@@ -675,11 +675,11 @@
  * on ARQ completion event reception by caller.
  * This function will commit SR to NVM.
  **/
-i40e_status i40e_update_nvm_checksum(struct i40e_hw *hw)
+int i40e_update_nvm_checksum(struct i40e_hw *hw)
 {
-	i40e_status ret_code;
-	u16 checksum;
 	__le16 le_sum;
+	int ret_code;
+	u16 checksum;
 
 	ret_code = i40e_calc_nvm_checksum(hw, &checksum);
 	le_sum = cpu_to_le16(checksum);
@@ -698,12 +698,12 @@
  * Performs checksum calculation and validates the NVM SW checksum. If the
  * caller does not need checksum, the value can be NULL.
  **/
-i40e_status i40e_validate_nvm_checksum(struct i40e_hw *hw,
-						 u16 *checksum)
+int i40e_validate_nvm_checksum(struct i40e_hw *hw,
+			       u16 *checksum)
 {
-	i40e_status ret_code = 0;
-	u16 checksum_sr = 0;
 	u16 checksum_local = 0;
+	u16 checksum_sr = 0;
+	int ret_code = 0;
 
 	/* We must acquire the NVM lock in order to correctly synchronize the
 	 * NVM accesses across multiple PFs. Without doing so it is possible
@@ -732,36 +732,36 @@
 	return ret_code;
 }
 
-static i40e_status i40e_nvmupd_state_init(struct i40e_hw *hw,
-					  struct i40e_nvm_access *cmd,
-					  u8 *bytes, int *perrno);
-static i40e_status i40e_nvmupd_state_reading(struct i40e_hw *hw,
-					     struct i40e_nvm_access *cmd,
-					     u8 *bytes, int *perrno);
-static i40e_status i40e_nvmupd_state_writing(struct i40e_hw *hw,
-					     struct i40e_nvm_access *cmd,
-					     u8 *bytes, int *errno);
+static int i40e_nvmupd_state_init(struct i40e_hw *hw,
+				  struct i40e_nvm_access *cmd,
+				  u8 *bytes, int *perrno);
+static int i40e_nvmupd_state_reading(struct i40e_hw *hw,
+				     struct i40e_nvm_access *cmd,
+				     u8 *bytes, int *perrno);
+static int i40e_nvmupd_state_writing(struct i40e_hw *hw,
+				     struct i40e_nvm_access *cmd,
+				     u8 *bytes, int *errno);
 static enum i40e_nvmupd_cmd i40e_nvmupd_validate_command(struct i40e_hw *hw,
 						struct i40e_nvm_access *cmd,
 						int *perrno);
-static i40e_status i40e_nvmupd_nvm_erase(struct i40e_hw *hw,
-					 struct i40e_nvm_access *cmd,
-					 int *perrno);
-static i40e_status i40e_nvmupd_nvm_write(struct i40e_hw *hw,
-					 struct i40e_nvm_access *cmd,
-					 u8 *bytes, int *perrno);
-static i40e_status i40e_nvmupd_nvm_read(struct i40e_hw *hw,
-					struct i40e_nvm_access *cmd,
-					u8 *bytes, int *perrno);
-static i40e_status i40e_nvmupd_exec_aq(struct i40e_hw *hw,
-				       struct i40e_nvm_access *cmd,
-				       u8 *bytes, int *perrno);
-static i40e_status i40e_nvmupd_get_aq_result(struct i40e_hw *hw,
-					     struct i40e_nvm_access *cmd,
-					     u8 *bytes, int *perrno);
-static i40e_status i40e_nvmupd_get_aq_event(struct i40e_hw *hw,
-					    struct i40e_nvm_access *cmd,
-					    u8 *bytes, int *perrno);
+static int i40e_nvmupd_nvm_erase(struct i40e_hw *hw,
+				 struct i40e_nvm_access *cmd,
+				 int *perrno);
+static int i40e_nvmupd_nvm_write(struct i40e_hw *hw,
+				 struct i40e_nvm_access *cmd,
+				 u8 *bytes, int *perrno);
+static int i40e_nvmupd_nvm_read(struct i40e_hw *hw,
+				struct i40e_nvm_access *cmd,
+				u8 *bytes, int *perrno);
+static int i40e_nvmupd_exec_aq(struct i40e_hw *hw,
+			       struct i40e_nvm_access *cmd,
+			       u8 *bytes, int *perrno);
+static int i40e_nvmupd_get_aq_result(struct i40e_hw *hw,
+				     struct i40e_nvm_access *cmd,
+				     u8 *bytes, int *perrno);
+static int i40e_nvmupd_get_aq_event(struct i40e_hw *hw,
+				    struct i40e_nvm_access *cmd,
+				    u8 *bytes, int *perrno);
 static inline u8 i40e_nvmupd_get_module(u32 val)
 {
 	return (u8)(val & I40E_NVM_MOD_PNT_MASK);
@@ -806,12 +806,12 @@
  *
  * Dispatches command depending on what update state is current
  **/
-i40e_status i40e_nvmupd_command(struct i40e_hw *hw,
-				struct i40e_nvm_access *cmd,
-				u8 *bytes, int *perrno)
+int i40e_nvmupd_command(struct i40e_hw *hw,
+			struct i40e_nvm_access *cmd,
+			u8 *bytes, int *perrno)
 {
-	i40e_status status;
 	enum i40e_nvmupd_cmd upd_cmd;
+	int status;
 
 	/* assume success */
 	*perrno = 0;
@@ -922,12 +922,12 @@
  * Process legitimate commands of the Init state and conditionally set next
  * state. Reject all other commands.
  **/
-static i40e_status i40e_nvmupd_state_init(struct i40e_hw *hw,
-					  struct i40e_nvm_access *cmd,
-					  u8 *bytes, int *perrno)
+static int i40e_nvmupd_state_init(struct i40e_hw *hw,
+				  struct i40e_nvm_access *cmd,
+				  u8 *bytes, int *perrno)
 {
-	i40e_status status = 0;
 	enum i40e_nvmupd_cmd upd_cmd;
+	int status = 0;
 
 	upd_cmd = i40e_nvmupd_validate_command(hw, cmd, perrno);
 
@@ -1061,12 +1061,12 @@
  * NVM ownership is already held.  Process legitimate commands and set any
  * change in state; reject all other commands.
  **/
-static i40e_status i40e_nvmupd_state_reading(struct i40e_hw *hw,
-					     struct i40e_nvm_access *cmd,
-					     u8 *bytes, int *perrno)
+static int i40e_nvmupd_state_reading(struct i40e_hw *hw,
+				     struct i40e_nvm_access *cmd,
+				     u8 *bytes, int *perrno)
 {
-	i40e_status status = 0;
 	enum i40e_nvmupd_cmd upd_cmd;
+	int status = 0;
 
 	upd_cmd = i40e_nvmupd_validate_command(hw, cmd, perrno);
 
@@ -1103,13 +1103,13 @@
  * NVM ownership is already held.  Process legitimate commands and set any
  * change in state; reject all other commands
  **/
-static i40e_status i40e_nvmupd_state_writing(struct i40e_hw *hw,
-					     struct i40e_nvm_access *cmd,
-					     u8 *bytes, int *perrno)
+static int i40e_nvmupd_state_writing(struct i40e_hw *hw,
+				     struct i40e_nvm_access *cmd,
+				     u8 *bytes, int *perrno)
 {
-	i40e_status status = 0;
 	enum i40e_nvmupd_cmd upd_cmd;
 	bool retry_attempt = false;
+	int status = 0;
 
 	upd_cmd = i40e_nvmupd_validate_command(hw, cmd, perrno);
 
@@ -1186,8 +1186,8 @@
 	 */
 	if (status && (hw->aq.asq_last_status == I40E_AQ_RC_EBUSY) &&
 	    !retry_attempt) {
-		i40e_status old_status = status;
 		u32 old_asq_status = hw->aq.asq_last_status;
+		int old_status = status;
 		u32 gtime;
 
 		gtime = rd32(hw, I40E_GLVFGEN_TIMER);
@@ -1369,17 +1369,17 @@
  *
  * cmd structure contains identifiers and data buffer
  **/
-static i40e_status i40e_nvmupd_exec_aq(struct i40e_hw *hw,
-				       struct i40e_nvm_access *cmd,
-				       u8 *bytes, int *perrno)
+static int i40e_nvmupd_exec_aq(struct i40e_hw *hw,
+			       struct i40e_nvm_access *cmd,
+			       u8 *bytes, int *perrno)
 {
 	struct i40e_asq_cmd_details cmd_details;
-	i40e_status status;
 	struct i40e_aq_desc *aq_desc;
 	u32 buff_size = 0;
 	u8 *buff = NULL;
 	u32 aq_desc_len;
 	u32 aq_data_len;
+	int status;
 
 	i40e_debug(hw, I40E_DEBUG_NVM, "NVMUPD: %s\n", __func__);
 	if (cmd->offset == 0xffff)
@@ -1428,8 +1428,8 @@
 				       buff_size, &cmd_details);
 	if (status) {
 		i40e_debug(hw, I40E_DEBUG_NVM,
-			   "i40e_nvmupd_exec_aq err %s aq_err %s\n",
-			   i40e_stat_str(hw, status),
+			   "%s err %d aq_err %s\n",
+			   __func__, status,
 			   i40e_aq_str(hw, hw->aq.asq_last_status));
 		*perrno = i40e_aq_rc_to_posix(status, hw->aq.asq_last_status);
 		return status;
@@ -1453,9 +1453,9 @@
  *
  * cmd structure contains identifiers and data buffer
  **/
-static i40e_status i40e_nvmupd_get_aq_result(struct i40e_hw *hw,
-					     struct i40e_nvm_access *cmd,
-					     u8 *bytes, int *perrno)
+static int i40e_nvmupd_get_aq_result(struct i40e_hw *hw,
+				     struct i40e_nvm_access *cmd,
+				     u8 *bytes, int *perrno)
 {
 	u32 aq_total_len;
 	u32 aq_desc_len;
@@ -1522,9 +1522,9 @@
  *
  * cmd structure contains identifiers and data buffer
  **/
-static i40e_status i40e_nvmupd_get_aq_event(struct i40e_hw *hw,
-					    struct i40e_nvm_access *cmd,
-					    u8 *bytes, int *perrno)
+static int i40e_nvmupd_get_aq_event(struct i40e_hw *hw,
+				    struct i40e_nvm_access *cmd,
+				    u8 *bytes, int *perrno)
 {
 	u32 aq_total_len;
 	u32 aq_desc_len;
@@ -1556,13 +1556,13 @@
  *
  * cmd structure contains identifiers and data buffer
  **/
-static i40e_status i40e_nvmupd_nvm_read(struct i40e_hw *hw,
-					struct i40e_nvm_access *cmd,
-					u8 *bytes, int *perrno)
+static int i40e_nvmupd_nvm_read(struct i40e_hw *hw,
+				struct i40e_nvm_access *cmd,
+				u8 *bytes, int *perrno)
 {
 	struct i40e_asq_cmd_details cmd_details;
-	i40e_status status;
 	u8 module, transaction;
+	int status;
 	bool last;
 
 	transaction = i40e_nvmupd_get_transaction(cmd->config);
@@ -1595,13 +1595,13 @@
  *
  * module, offset, data_size and data are in cmd structure
  **/
-static i40e_status i40e_nvmupd_nvm_erase(struct i40e_hw *hw,
-					 struct i40e_nvm_access *cmd,
-					 int *perrno)
+static int i40e_nvmupd_nvm_erase(struct i40e_hw *hw,
+				 struct i40e_nvm_access *cmd,
+				 int *perrno)
 {
-	i40e_status status = 0;
 	struct i40e_asq_cmd_details cmd_details;
 	u8 module, transaction;
+	int status = 0;
 	bool last;
 
 	transaction = i40e_nvmupd_get_transaction(cmd->config);
@@ -1635,14 +1635,14 @@
  *
  * module, offset, data_size and data are in cmd structure
  **/
-static i40e_status i40e_nvmupd_nvm_write(struct i40e_hw *hw,
-					 struct i40e_nvm_access *cmd,
-					 u8 *bytes, int *perrno)
+static int i40e_nvmupd_nvm_write(struct i40e_hw *hw,
+				 struct i40e_nvm_access *cmd,
+				 u8 *bytes, int *perrno)
 {
-	i40e_status status = 0;
 	struct i40e_asq_cmd_details cmd_details;
 	u8 module, transaction;
 	u8 preservation_flags;
+	int status = 0;
 	bool last;
 
 	transaction = i40e_nvmupd_get_transaction(cmd->config);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_osdep.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_osdep.h
@@ -56,5 +56,4 @@
 			(h)->bus.func, ##__VA_ARGS__);		\
 } while (0)
 
-typedef enum i40e_status_code i40e_status;
 #endif /* _I40E_OSDEP_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_prototype.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_prototype.h
@@ -16,17 +16,17 @@
  */
 
 /* adminq functions */
-i40e_status i40e_init_adminq(struct i40e_hw *hw);
+int i40e_init_adminq(struct i40e_hw *hw);
 void i40e_shutdown_adminq(struct i40e_hw *hw);
 void i40e_adminq_init_ring_data(struct i40e_hw *hw);
-i40e_status i40e_clean_arq_element(struct i40e_hw *hw,
-					     struct i40e_arq_event_info *e,
-					     u16 *events_pending);
-i40e_status i40e_asq_send_command(struct i40e_hw *hw,
-				struct i40e_aq_desc *desc,
-				void *buff, /* can be NULL */
-				u16  buff_size,
-				struct i40e_asq_cmd_details *cmd_details);
+int i40e_clean_arq_element(struct i40e_hw *hw,
+			   struct i40e_arq_event_info *e,
+			   u16 *events_pending);
+int i40e_asq_send_command(struct i40e_hw *hw,
+			  struct i40e_aq_desc *desc,
+			  void *buff, /* can be NULL */
+			  u16  buff_size,
+			  struct i40e_asq_cmd_details *cmd_details);
 
 /* debug function for adminq */
 void i40e_debug_aq(struct i40e_hw *hw, enum i40e_debug_mask mask,
@@ -34,314 +34,269 @@
 
 void i40e_idle_aq(struct i40e_hw *hw);
 bool i40e_check_asq_alive(struct i40e_hw *hw);
-i40e_status i40e_aq_queue_shutdown(struct i40e_hw *hw, bool unloading);
+int i40e_aq_queue_shutdown(struct i40e_hw *hw, bool unloading);
 const char *i40e_aq_str(struct i40e_hw *hw, enum i40e_admin_queue_err aq_err);
-const char *i40e_stat_str(struct i40e_hw *hw, i40e_status stat_err);
 
-i40e_status i40e_aq_get_rss_lut(struct i40e_hw *hw, u16 seid,
-				bool pf_lut, u8 *lut, u16 lut_size);
-i40e_status i40e_aq_set_rss_lut(struct i40e_hw *hw, u16 seid,
-				bool pf_lut, u8 *lut, u16 lut_size);
-i40e_status i40e_aq_get_rss_key(struct i40e_hw *hw,
-				u16 seid,
-				struct i40e_aqc_get_set_rss_key_data *key);
-i40e_status i40e_aq_set_rss_key(struct i40e_hw *hw,
-				u16 seid,
-				struct i40e_aqc_get_set_rss_key_data *key);
+int i40e_aq_get_rss_lut(struct i40e_hw *hw, u16 seid,
+			bool pf_lut, u8 *lut, u16 lut_size);
+int i40e_aq_set_rss_lut(struct i40e_hw *hw, u16 seid,
+			bool pf_lut, u8 *lut, u16 lut_size);
+int i40e_aq_get_rss_key(struct i40e_hw *hw, u16 seid,
+			struct i40e_aqc_get_set_rss_key_data *key);
+int i40e_aq_set_rss_key(struct i40e_hw *hw, u16 seid,
+			struct i40e_aqc_get_set_rss_key_data *key);
 
 u32 i40e_led_get(struct i40e_hw *hw);
 void i40e_led_set(struct i40e_hw *hw, u32 mode, bool blink);
-i40e_status i40e_led_set_phy(struct i40e_hw *hw, bool on,
-			     u16 led_addr, u32 mode);
-i40e_status i40e_led_get_phy(struct i40e_hw *hw, u16 *led_addr,
-			     u16 *val);
-i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
-				    u32 time, u32 interval);
+int i40e_led_set_phy(struct i40e_hw *hw, bool on, u16 led_addr, u32 mode);
+int i40e_led_get_phy(struct i40e_hw *hw, u16 *led_addr, u16 *val);
+int i40e_blink_phy_link_led(struct i40e_hw *hw, u32 time, u32 interval);
 
 /* admin send queue commands */
 
-i40e_status i40e_aq_get_firmware_version(struct i40e_hw *hw,
-				u16 *fw_major_version, u16 *fw_minor_version,
-				u32 *fw_build,
-				u16 *api_major_version, u16 *api_minor_version,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_debug_write_register(struct i40e_hw *hw,
-					u32 reg_addr, u64 reg_val,
-					struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_debug_read_register(struct i40e_hw *hw,
-				u32  reg_addr, u64 *reg_val,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_phy_debug(struct i40e_hw *hw, u8 cmd_flags,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_default_vsi(struct i40e_hw *hw, u16 vsi_id,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_clear_default_vsi(struct i40e_hw *hw, u16 vsi_id,
-				      struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code i40e_aq_get_phy_capabilities(struct i40e_hw *hw,
-			bool qualified_modules, bool report_init,
-			struct i40e_aq_get_phy_abilities_resp *abilities,
-			struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code i40e_aq_set_phy_config(struct i40e_hw *hw,
-				struct i40e_aq_set_phy_config *config,
-				struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
-				  bool atomic_reset);
-i40e_status i40e_aq_set_phy_int_mask(struct i40e_hw *hw, u16 mask,
-				     struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_clear_pxe_mode(struct i40e_hw *hw,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_link_restart_an(struct i40e_hw *hw,
-					bool enable_link,
-					struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_get_link_info(struct i40e_hw *hw,
-				bool enable_lse, struct i40e_link_status *link,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_local_advt_reg(struct i40e_hw *hw,
-				u64 advt_reg,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_send_driver_version(struct i40e_hw *hw,
+int i40e_aq_get_firmware_version(struct i40e_hw *hw,
+				 u16 *fw_major_version, u16 *fw_minor_version,
+				 u32 *fw_build,
+				 u16 *api_major_version, u16 *api_minor_version,
+				 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_debug_write_register(struct i40e_hw *hw, u32 reg_addr, u64 reg_val,
+				 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_debug_read_register(struct i40e_hw *hw,
+				u32 reg_addr, u64 *reg_val,
+				struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_phy_debug(struct i40e_hw *hw, u8 cmd_flags,
+			  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_default_vsi(struct i40e_hw *hw, u16 vsi_id,
+			    struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_clear_default_vsi(struct i40e_hw *hw, u16 vsi_id,
+			      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_phy_capabilities(struct i40e_hw *hw,
+				 bool qualified_modules, bool report_init,
+				 struct i40e_aq_get_phy_abilities_resp *abilities,
+				 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_phy_config(struct i40e_hw *hw, struct i40e_aq_set_phy_config *config,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures, bool atomic_reset);
+int i40e_aq_set_phy_int_mask(struct i40e_hw *hw, u16 mask,
+			     struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_clear_pxe_mode(struct i40e_hw *hw,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_link_restart_an(struct i40e_hw *hw, bool enable_link,
+				struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_link_info(struct i40e_hw *hw, bool enable_lse,
+			  struct i40e_link_status *link,
+			  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_local_advt_reg(struct i40e_hw *hw, u64 advt_reg,
+			       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_send_driver_version(struct i40e_hw *hw,
 				struct i40e_driver_version *dv,
 				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_add_vsi(struct i40e_hw *hw,
-				struct i40e_vsi_context *vsi_ctx,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_vsi_broadcast(struct i40e_hw *hw,
-				u16 vsi_id, bool set_filter,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_vsi_unicast_promiscuous(struct i40e_hw *hw,
-		u16 vsi_id, bool set, struct i40e_asq_cmd_details *cmd_details,
-		bool rx_only_promisc);
-i40e_status i40e_aq_set_vsi_multicast_promiscuous(struct i40e_hw *hw,
-		u16 vsi_id, bool set, struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code i40e_aq_set_vsi_mc_promisc_on_vlan(struct i40e_hw *hw,
-							 u16 seid, bool enable,
-							 u16 vid,
-				struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code i40e_aq_set_vsi_uc_promisc_on_vlan(struct i40e_hw *hw,
-							 u16 seid, bool enable,
-							 u16 vid,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_vsi_bc_promisc_on_vlan(struct i40e_hw *hw,
-				u16 seid, bool enable, u16 vid,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_vsi_vlan_promisc(struct i40e_hw *hw,
-				u16 seid, bool enable,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_get_vsi_params(struct i40e_hw *hw,
-				struct i40e_vsi_context *vsi_ctx,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_update_vsi_params(struct i40e_hw *hw,
-				struct i40e_vsi_context *vsi_ctx,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_add_veb(struct i40e_hw *hw, u16 uplink_seid,
-				u16 downlink_seid, u8 enabled_tc,
-				bool default_port, u16 *pveb_seid,
-				bool enable_stats,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_get_veb_parameters(struct i40e_hw *hw,
-				u16 veb_seid, u16 *switch_id, bool *floating,
-				u16 *statistic_index, u16 *vebs_used,
-				u16 *vebs_free,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_add_macvlan(struct i40e_hw *hw, u16 vsi_id,
+int i40e_aq_add_vsi(struct i40e_hw *hw,
+		    struct i40e_vsi_context *vsi_ctx,
+		    struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_vsi_broadcast(struct i40e_hw *hw, u16 vsi_id, bool set_filter,
+			      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_vsi_unicast_promiscuous(struct i40e_hw *hw,
+					u16 vsi_id, bool set,
+					struct i40e_asq_cmd_details *cmd_details,
+					bool rx_only_promisc);
+int i40e_aq_set_vsi_multicast_promiscuous(struct i40e_hw *hw,
+					  u16 vsi_id, bool set,
+					  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_vsi_mc_promisc_on_vlan(struct i40e_hw *hw, u16 seid,
+				       bool enable, u16 vid,
+				       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_vsi_uc_promisc_on_vlan(struct i40e_hw *hw,
+				       u16 seid, bool enable, u16 vid,
+				       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_vsi_bc_promisc_on_vlan(struct i40e_hw *hw,
+				       u16 seid, bool enable, u16 vid,
+				       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_vsi_vlan_promisc(struct i40e_hw *hw,
+				 u16 seid, bool enable,
+				 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_vsi_params(struct i40e_hw *hw,
+			   struct i40e_vsi_context *vsi_ctx,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_update_vsi_params(struct i40e_hw *hw,
+			      struct i40e_vsi_context *vsi_ctx,
+			      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_add_veb(struct i40e_hw *hw, u16 uplink_seid,
+		    u16 downlink_seid, u8 enabled_tc,
+		    bool default_port, u16 *pveb_seid,
+		    bool enable_stats,
+		    struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_veb_parameters(struct i40e_hw *hw,
+			       u16 veb_seid, u16 *switch_id, bool *floating,
+			       u16 *statistic_index, u16 *vebs_used,
+			       u16 *vebs_free,
+			       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_add_macvlan(struct i40e_hw *hw, u16 vsi_id,
 			struct i40e_aqc_add_macvlan_element_data *mv_list,
 			u16 count, struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_remove_macvlan(struct i40e_hw *hw, u16 vsi_id,
-			struct i40e_aqc_remove_macvlan_element_data *mv_list,
-			u16 count, struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_add_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
-			u16 rule_type, u16 dest_vsi, u16 count, __le16 *mr_list,
-			struct i40e_asq_cmd_details *cmd_details,
-			u16 *rule_id, u16 *rules_used, u16 *rules_free);
-i40e_status i40e_aq_delete_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
-			u16 rule_type, u16 rule_id, u16 count, __le16 *mr_list,
-			struct i40e_asq_cmd_details *cmd_details,
-			u16 *rules_used, u16 *rules_free);
-
-i40e_status i40e_aq_send_msg_to_vf(struct i40e_hw *hw, u16 vfid,
-				u32 v_opcode, u32 v_retval, u8 *msg, u16 msglen,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_get_switch_config(struct i40e_hw *hw,
-				struct i40e_aqc_get_switch_config_resp *buf,
-				u16 buf_size, u16 *start_seid,
-				struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code i40e_aq_set_switch_config(struct i40e_hw *hw,
-						u16 flags,
-						u16 valid_flags, u8 mode,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_request_resource(struct i40e_hw *hw,
-				enum i40e_aq_resources_ids resource,
-				enum i40e_aq_resource_access_type access,
-				u8 sdp_number, u64 *timeout,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_release_resource(struct i40e_hw *hw,
-				enum i40e_aq_resources_ids resource,
-				u8 sdp_number,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_read_nvm(struct i40e_hw *hw, u8 module_pointer,
-				u32 offset, u16 length, void *data,
-				bool last_command,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_erase_nvm(struct i40e_hw *hw, u8 module_pointer,
-			      u32 offset, u16 length, bool last_command,
+int i40e_aq_remove_macvlan(struct i40e_hw *hw, u16 vsi_id,
+			   struct i40e_aqc_remove_macvlan_element_data *mv_list,
+			   u16 count, struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_add_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
+			   u16 rule_type, u16 dest_vsi, u16 count,
+			   __le16 *mr_list,
+			   struct i40e_asq_cmd_details *cmd_details,
+			   u16 *rule_id, u16 *rules_used, u16 *rules_free);
+int i40e_aq_delete_mirrorrule(struct i40e_hw *hw, u16 sw_seid,
+			      u16 rule_type, u16 rule_id, u16 count, __le16 *mr_list,
+			      struct i40e_asq_cmd_details *cmd_details,
+			      u16 *rules_used, u16 *rules_free);
+
+int i40e_aq_send_msg_to_vf(struct i40e_hw *hw, u16 vfid,
+			   u32 v_opcode, u32 v_retval, u8 *msg, u16 msglen,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_switch_config(struct i40e_hw *hw,
+			      struct i40e_aqc_get_switch_config_resp *buf,
+			      u16 buf_size, u16 *start_seid,
 			      struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_discover_capabilities(struct i40e_hw *hw,
-				void *buff, u16 buff_size, u16 *data_size,
-				enum i40e_admin_queue_opc list_type_opc,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_update_nvm(struct i40e_hw *hw, u8 module_pointer,
-				u32 offset, u16 length, void *data,
-				bool last_command, u8 preservation_flags,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_rearrange_nvm(struct i40e_hw *hw,
-				  u8 rearrange_nvm,
-				  struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_get_lldp_mib(struct i40e_hw *hw, u8 bridge_type,
-				u8 mib_type, void *buff, u16 buff_size,
-				u16 *local_len, u16 *remote_len,
-				struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code
-i40e_aq_set_lldp_mib(struct i40e_hw *hw,
-		     u8 mib_type, void *buff, u16 buff_size,
-		     struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_cfg_lldp_mib_change_event(struct i40e_hw *hw,
-				bool enable_update,
-				struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code
-i40e_aq_restore_lldp(struct i40e_hw *hw, u8 *setting, bool restore,
+int i40e_aq_set_switch_config(struct i40e_hw *hw, u16 flags,
+			      u16 valid_flags, u8 mode,
+			      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_request_resource(struct i40e_hw *hw,
+			     enum i40e_aq_resources_ids resource,
+			     enum i40e_aq_resource_access_type access,
+			     u8 sdp_number, u64 *timeout,
+			     struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_release_resource(struct i40e_hw *hw,
+			     enum i40e_aq_resources_ids resource, u8 sdp_number,
+			     struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_read_nvm(struct i40e_hw *hw, u8 module_pointer,
+		     u32 offset, u16 length, void *data, bool last_command,
 		     struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_stop_lldp(struct i40e_hw *hw, bool shutdown_agent,
-			      bool persist,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_set_dcb_parameters(struct i40e_hw *hw,
-				       bool dcb_enable,
-				       struct i40e_asq_cmd_details
-				       *cmd_details);
-i40e_status i40e_aq_start_lldp(struct i40e_hw *hw, bool persist,
+int i40e_aq_erase_nvm(struct i40e_hw *hw, u8 module_pointer,
+		      u32 offset, u16 length, bool last_command,
+		      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_discover_capabilities(struct i40e_hw *hw,
+				  void *buff, u16 buff_size, u16 *data_size,
+				  enum i40e_admin_queue_opc list_type_opc,
+				  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_update_nvm(struct i40e_hw *hw, u8 module_pointer,
+		       u32 offset, u16 length, void *data,
+		       bool last_command, u8 preservation_flags,
+		       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_rearrange_nvm(struct i40e_hw *hw, u8 rearrange_nvm,
+			  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_lldp_mib(struct i40e_hw *hw, u8 bridge_type,
+			 u8 mib_type, void *buff, u16 buff_size,
+			 u16 *local_len, u16 *remote_len,
+			 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_lldp_mib(struct i40e_hw *hw, u8 mib_type,
+			 void *buff, u16 buff_size,
+			 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_cfg_lldp_mib_change_event(struct i40e_hw *hw,
+				      bool enable_update,
+				      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_restore_lldp(struct i40e_hw *hw, u8 *setting, bool restore,
+			 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_stop_lldp(struct i40e_hw *hw, bool shutdown_agent, bool persist,
+		      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_set_dcb_parameters(struct i40e_hw *hw, bool dcb_enable,
 			       struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_get_cee_dcb_config(struct i40e_hw *hw,
-				       void *buff, u16 buff_size,
-				       struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_add_udp_tunnel(struct i40e_hw *hw,
-				u16 udp_port, u8 protocol_index,
-				u8 *filter_index,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_del_udp_tunnel(struct i40e_hw *hw, u8 index,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_delete_element(struct i40e_hw *hw, u16 seid,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_mac_address_write(struct i40e_hw *hw,
-				    u16 flags, u8 *mac_addr,
-				    struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_config_vsi_bw_limit(struct i40e_hw *hw,
+int i40e_aq_start_lldp(struct i40e_hw *hw, bool persist,
+		       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_get_cee_dcb_config(struct i40e_hw *hw,
+			       void *buff, u16 buff_size,
+			       struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_add_udp_tunnel(struct i40e_hw *hw, u16 udp_port,
+			   u8 protocol_index, u8 *filter_index,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_del_udp_tunnel(struct i40e_hw *hw, u8 index,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_delete_element(struct i40e_hw *hw, u16 seid,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_mac_address_write(struct i40e_hw *hw, u16 flags, u8 *mac_addr,
+			      struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_config_vsi_bw_limit(struct i40e_hw *hw,
 				u16 seid, u16 credit, u8 max_credit,
 				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_dcb_updated(struct i40e_hw *hw,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_config_switch_comp_bw_limit(struct i40e_hw *hw,
-				u16 seid, u16 credit, u8 max_bw,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_config_vsi_tc_bw(struct i40e_hw *hw, u16 seid,
-			struct i40e_aqc_configure_vsi_tc_bw_data *bw_data,
+int i40e_aq_dcb_updated(struct i40e_hw *hw,
 			struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_config_switch_comp_ets(struct i40e_hw *hw,
-		u16 seid,
-		struct i40e_aqc_configure_switching_comp_ets_data *ets_data,
-		enum i40e_admin_queue_opc opcode,
-		struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_config_switch_comp_bw_config(struct i40e_hw *hw,
-	u16 seid,
-	struct i40e_aqc_configure_switching_comp_bw_config_data *bw_data,
-	struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_query_vsi_bw_config(struct i40e_hw *hw,
-			u16 seid,
-			struct i40e_aqc_query_vsi_bw_config_resp *bw_data,
-			struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_query_vsi_ets_sla_config(struct i40e_hw *hw,
-			u16 seid,
-			struct i40e_aqc_query_vsi_ets_sla_config_resp *bw_data,
-			struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_query_switch_comp_ets_config(struct i40e_hw *hw,
-		u16 seid,
-		struct i40e_aqc_query_switching_comp_ets_config_resp *bw_data,
-		struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_query_port_ets_config(struct i40e_hw *hw,
-		u16 seid,
-		struct i40e_aqc_query_port_ets_config_resp *bw_data,
-		struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_query_switch_comp_bw_config(struct i40e_hw *hw,
-		u16 seid,
+int i40e_aq_config_switch_comp_bw_limit(struct i40e_hw *hw,
+					u16 seid, u16 credit, u8 max_bw,
+					struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_config_vsi_tc_bw(struct i40e_hw *hw, u16 seid,
+			     struct i40e_aqc_configure_vsi_tc_bw_data *bw_data,
+			     struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_config_switch_comp_ets(struct i40e_hw *hw, u16 seid,
+				   struct i40e_aqc_configure_switching_comp_ets_data *ets_data,
+				   enum i40e_admin_queue_opc opcode,
+				   struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_config_switch_comp_bw_config(struct i40e_hw *hw, u16 seid,
+					 struct i40e_aqc_configure_switching_comp_bw_config_data *bw_data,
+					 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_query_vsi_bw_config(struct i40e_hw *hw, u16 seid,
+				struct i40e_aqc_query_vsi_bw_config_resp *bw_data,
+				struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_query_vsi_ets_sla_config(struct i40e_hw *hw, u16 seid,
+				     struct i40e_aqc_query_vsi_ets_sla_config_resp *bw_data,
+				     struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_query_switch_comp_ets_config(struct i40e_hw *hw, u16 seid,
+					 struct i40e_aqc_query_switching_comp_ets_config_resp *bw_data,
+					 struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_query_port_ets_config(struct i40e_hw *hw, u16 seid,
+				  struct i40e_aqc_query_port_ets_config_resp *bw_data,
+				  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_query_switch_comp_bw_config(struct i40e_hw *hw, u16 seid,
 		struct i40e_aqc_query_switching_comp_bw_config_resp *bw_data,
 		struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_resume_port_tx(struct i40e_hw *hw,
-				   struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code
-i40e_aq_add_cloud_filters_bb(struct i40e_hw *hw, u16 seid,
-			     struct i40e_aqc_cloud_filters_element_bb *filters,
-			     u8 filter_count);
-enum i40e_status_code
-i40e_aq_add_cloud_filters(struct i40e_hw *hw, u16 vsi,
-			  struct i40e_aqc_cloud_filters_element_data *filters,
-			  u8 filter_count);
-enum i40e_status_code
-i40e_aq_rem_cloud_filters(struct i40e_hw *hw, u16 vsi,
-			  struct i40e_aqc_cloud_filters_element_data *filters,
-			  u8 filter_count);
-enum i40e_status_code
-i40e_aq_rem_cloud_filters_bb(struct i40e_hw *hw, u16 seid,
-			     struct i40e_aqc_cloud_filters_element_bb *filters,
-			     u8 filter_count);
-i40e_status i40e_read_lldp_cfg(struct i40e_hw *hw,
-			       struct i40e_lldp_variables *lldp_cfg);
-enum i40e_status_code
-i40e_aq_suspend_port_tx(struct i40e_hw *hw, u16 seid,
-			struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_resume_port_tx(struct i40e_hw *hw, struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_add_cloud_filters_bb(struct i40e_hw *hw, u16 seid,
+				 struct i40e_aqc_cloud_filters_element_bb *filters,
+				 u8 filter_count);
+int i40e_aq_add_cloud_filters(struct i40e_hw *hw, u16 vsi,
+			      struct i40e_aqc_cloud_filters_element_data *filters,
+			      u8 filter_count);
+int i40e_aq_rem_cloud_filters(struct i40e_hw *hw, u16 vsi,
+			      struct i40e_aqc_cloud_filters_element_data *filters,
+			      u8 filter_count);
+int i40e_aq_rem_cloud_filters_bb(struct i40e_hw *hw, u16 seid,
+				 struct i40e_aqc_cloud_filters_element_bb *filters,
+				 u8 filter_count);
+int i40e_read_lldp_cfg(struct i40e_hw *hw, struct i40e_lldp_variables *lldp_cfg);
+int i40e_aq_suspend_port_tx(struct i40e_hw *hw, u16 seid,
+			    struct i40e_asq_cmd_details *cmd_details);
 /* i40e_common */
-i40e_status i40e_init_shared_code(struct i40e_hw *hw);
-i40e_status i40e_pf_reset(struct i40e_hw *hw);
+int i40e_init_shared_code(struct i40e_hw *hw);
+int i40e_pf_reset(struct i40e_hw *hw);
 void i40e_clear_hw(struct i40e_hw *hw);
 void i40e_clear_pxe_mode(struct i40e_hw *hw);
-i40e_status i40e_get_link_status(struct i40e_hw *hw, bool *link_up);
-i40e_status i40e_update_link_info(struct i40e_hw *hw);
-i40e_status i40e_get_mac_addr(struct i40e_hw *hw, u8 *mac_addr);
-i40e_status i40e_read_bw_from_alt_ram(struct i40e_hw *hw,
-				      u32 *max_bw, u32 *min_bw, bool *min_valid,
-				      bool *max_valid);
-i40e_status i40e_aq_configure_partition_bw(struct i40e_hw *hw,
-			struct i40e_aqc_configure_partition_bw_data *bw_data,
-			struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_get_port_mac_addr(struct i40e_hw *hw, u8 *mac_addr);
-i40e_status i40e_read_pba_string(struct i40e_hw *hw, u8 *pba_num,
-				 u32 pba_num_size);
-i40e_status i40e_validate_mac_addr(u8 *mac_addr);
+int i40e_get_link_status(struct i40e_hw *hw, bool *link_up);
+int i40e_update_link_info(struct i40e_hw *hw);
+int i40e_get_mac_addr(struct i40e_hw *hw, u8 *mac_addr);
+int i40e_read_bw_from_alt_ram(struct i40e_hw *hw,
+			      u32 *max_bw, u32 *min_bw, bool *min_valid,
+			      bool *max_valid);
+int i40e_aq_configure_partition_bw(struct i40e_hw *hw,
+				   struct i40e_aqc_configure_partition_bw_data *bw_data,
+				   struct i40e_asq_cmd_details *cmd_details);
+int i40e_get_port_mac_addr(struct i40e_hw *hw, u8 *mac_addr);
+int i40e_read_pba_string(struct i40e_hw *hw, u8 *pba_num, u32 pba_num_size);
+int i40e_validate_mac_addr(u8 *mac_addr);
 void i40e_pre_tx_queue_cfg(struct i40e_hw *hw, u32 queue, bool enable);
 /* prototype for functions used for NVM access */
-i40e_status i40e_init_nvm(struct i40e_hw *hw);
-i40e_status i40e_acquire_nvm(struct i40e_hw *hw,
-				      enum i40e_aq_resource_access_type access);
+int i40e_init_nvm(struct i40e_hw *hw);
+int i40e_acquire_nvm(struct i40e_hw *hw, enum i40e_aq_resource_access_type access);
 void i40e_release_nvm(struct i40e_hw *hw);
-i40e_status i40e_read_nvm_word(struct i40e_hw *hw, u16 offset,
-					 u16 *data);
-enum i40e_status_code i40e_read_nvm_module_data(struct i40e_hw *hw,
-						u8 module_ptr,
-						u16 module_offset,
-						u16 data_offset,
-						u16 words_data_size,
-						u16 *data_ptr);
-i40e_status i40e_read_nvm_buffer(struct i40e_hw *hw, u16 offset,
-				 u16 *words, u16 *data);
-i40e_status i40e_update_nvm_checksum(struct i40e_hw *hw);
-i40e_status i40e_validate_nvm_checksum(struct i40e_hw *hw,
-						 u16 *checksum);
-i40e_status i40e_nvmupd_command(struct i40e_hw *hw,
-				struct i40e_nvm_access *cmd,
-				u8 *bytes, int *);
+int i40e_read_nvm_word(struct i40e_hw *hw, u16 offset, u16 *data);
+int i40e_read_nvm_module_data(struct i40e_hw *hw, u8 module_ptr,
+			      u16 module_offset, u16 data_offset,
+			      u16 words_data_size, u16 *data_ptr);
+int i40e_read_nvm_buffer(struct i40e_hw *hw, u16 offset, u16 *words, u16 *data);
+int i40e_update_nvm_checksum(struct i40e_hw *hw);
+int i40e_validate_nvm_checksum(struct i40e_hw *hw, u16 *checksum);
+int i40e_nvmupd_command(struct i40e_hw *hw, struct i40e_nvm_access *cmd,
+			u8 *bytes, int *);
 void i40e_nvmupd_check_wait_event(struct i40e_hw *hw, u16 opcode,
 				  struct i40e_aq_desc *desc);
 void i40e_nvmupd_clear_wait_state(struct i40e_hw *hw);
 void i40e_set_pci_config_data(struct i40e_hw *hw, u16 link_status);
 
-i40e_status i40e_set_mac_type(struct i40e_hw *hw);
+int i40e_set_mac_type(struct i40e_hw *hw);
 
 extern struct i40e_rx_ptype_decoded i40e_ptype_lookup[];
 
@@ -390,41 +345,41 @@
 /* i40e_common for VF drivers*/
 void i40e_vf_parse_hw_config(struct i40e_hw *hw,
 			     struct virtchnl_vf_resource *msg);
-i40e_status i40e_vf_reset(struct i40e_hw *hw);
-i40e_status i40e_aq_send_msg_to_pf(struct i40e_hw *hw,
-				enum virtchnl_ops v_opcode,
-				i40e_status v_retval,
-				u8 *msg, u16 msglen,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_set_filter_control(struct i40e_hw *hw,
-				struct i40e_filter_control_settings *settings);
-i40e_status i40e_aq_add_rem_control_packet_filter(struct i40e_hw *hw,
-				u8 *mac_addr, u16 ethtype, u16 flags,
-				u16 vsi_seid, u16 queue, bool is_add,
-				struct i40e_control_filter_stats *stats,
-				struct i40e_asq_cmd_details *cmd_details);
-i40e_status i40e_aq_debug_dump(struct i40e_hw *hw, u8 cluster_id,
-			       u8 table_id, u32 start_index, u16 buff_size,
-			       void *buff, u16 *ret_buff_size,
-			       u8 *ret_next_table, u32 *ret_next_index,
-			       struct i40e_asq_cmd_details *cmd_details);
+int i40e_vf_reset(struct i40e_hw *hw);
+int i40e_aq_send_msg_to_pf(struct i40e_hw *hw,
+			   enum virtchnl_ops v_opcode,
+			   int v_retval,
+			   u8 *msg, u16 msglen,
+			   struct i40e_asq_cmd_details *cmd_details);
+int i40e_set_filter_control(struct i40e_hw *hw,
+			    struct i40e_filter_control_settings *settings);
+int i40e_aq_add_rem_control_packet_filter(struct i40e_hw *hw,
+					  u8 *mac_addr, u16 ethtype, u16 flags,
+					  u16 vsi_seid, u16 queue, bool is_add,
+					  struct i40e_control_filter_stats *stats,
+					  struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_debug_dump(struct i40e_hw *hw, u8 cluster_id,
+		       u8 table_id, u32 start_index, u16 buff_size,
+		       void *buff, u16 *ret_buff_size,
+		       u8 *ret_next_table, u32 *ret_next_index,
+		       struct i40e_asq_cmd_details *cmd_details);
 void i40e_add_filter_to_drop_tx_flow_control_frames(struct i40e_hw *hw,
 						    u16 vsi_seid);
-i40e_status i40e_aq_rx_ctl_read_register(struct i40e_hw *hw,
-				u32 reg_addr, u32 *reg_val,
-				struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_rx_ctl_read_register(struct i40e_hw *hw,
+				 u32 reg_addr, u32 *reg_val,
+				 struct i40e_asq_cmd_details *cmd_details);
 u32 i40e_read_rx_ctl(struct i40e_hw *hw, u32 reg_addr);
-i40e_status i40e_aq_rx_ctl_write_register(struct i40e_hw *hw,
-				u32 reg_addr, u32 reg_val,
-				struct i40e_asq_cmd_details *cmd_details);
+int i40e_aq_rx_ctl_write_register(struct i40e_hw *hw,
+				  u32 reg_addr, u32 reg_val,
+				  struct i40e_asq_cmd_details *cmd_details);
 void i40e_write_rx_ctl(struct i40e_hw *hw, u32 reg_addr, u32 reg_val);
-enum i40e_status_code
+int
 i40e_aq_set_phy_register_ext(struct i40e_hw *hw,
 			     u8 phy_select, u8 dev_addr, bool page_change,
 			     bool set_mdio, u8 mdio_num,
 			     u32 reg_addr, u32 reg_val,
 			     struct i40e_asq_cmd_details *cmd_details);
-enum i40e_status_code
+int
 i40e_aq_get_phy_register_ext(struct i40e_hw *hw,
 			     u8 phy_select, u8 dev_addr, bool page_change,
 			     bool set_mdio, u8 mdio_num,
@@ -437,43 +392,43 @@
 #define i40e_aq_get_phy_register(hw, ps, da, pc, ra, rv, cd)		\
 	i40e_aq_get_phy_register_ext(hw, ps, da, pc, false, 0, ra, rv, cd)
 
-i40e_status i40e_read_phy_register_clause22(struct i40e_hw *hw,
-					    u16 reg, u8 phy_addr, u16 *value);
-i40e_status i40e_write_phy_register_clause22(struct i40e_hw *hw,
-					     u16 reg, u8 phy_addr, u16 value);
-i40e_status i40e_read_phy_register_clause45(struct i40e_hw *hw,
-				u8 page, u16 reg, u8 phy_addr, u16 *value);
-i40e_status i40e_write_phy_register_clause45(struct i40e_hw *hw,
-				u8 page, u16 reg, u8 phy_addr, u16 value);
-i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
-				   u8 phy_addr, u16 *value);
-i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
-				    u8 phy_addr, u16 value);
+int i40e_read_phy_register_clause22(struct i40e_hw *hw,
+				    u16 reg, u8 phy_addr, u16 *value);
+int i40e_write_phy_register_clause22(struct i40e_hw *hw,
+				     u16 reg, u8 phy_addr, u16 value);
+int i40e_read_phy_register_clause45(struct i40e_hw *hw,
+				    u8 page, u16 reg, u8 phy_addr, u16 *value);
+int i40e_write_phy_register_clause45(struct i40e_hw *hw,
+				     u8 page, u16 reg, u8 phy_addr, u16 value);
+int i40e_read_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
+			   u8 phy_addr, u16 *value);
+int i40e_write_phy_register(struct i40e_hw *hw, u8 page, u16 reg,
+			    u8 phy_addr, u16 value);
 u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
-i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
-				    u32 time, u32 interval);
-i40e_status i40e_aq_write_ddp(struct i40e_hw *hw, void *buff,
-			      u16 buff_size, u32 track_id,
-			      u32 *error_offset, u32 *error_info,
-			      struct i40e_asq_cmd_details *
-			      cmd_details);
-i40e_status i40e_aq_get_ddp_list(struct i40e_hw *hw, void *buff,
-				 u16 buff_size, u8 flags,
-				 struct i40e_asq_cmd_details *
-				 cmd_details);
+int i40e_blink_phy_link_led(struct i40e_hw *hw,
+			    u32 time, u32 interval);
+int i40e_aq_write_ddp(struct i40e_hw *hw, void *buff,
+		      u16 buff_size, u32 track_id,
+		      u32 *error_offset, u32 *error_info,
+		      struct i40e_asq_cmd_details *
+		      cmd_details);
+int i40e_aq_get_ddp_list(struct i40e_hw *hw, void *buff,
+			 u16 buff_size, u8 flags,
+			 struct i40e_asq_cmd_details *
+			 cmd_details);
 struct i40e_generic_seg_header *
 i40e_find_segment_in_package(u32 segment_type,
 			     struct i40e_package_header *pkg_header);
 struct i40e_profile_section_header *
 i40e_find_section_in_profile(u32 section_type,
 			     struct i40e_profile_segment *profile);
-enum i40e_status_code
+int
 i40e_write_profile(struct i40e_hw *hw, struct i40e_profile_segment *i40e_seg,
 		   u32 track_id);
-enum i40e_status_code
+int
 i40e_rollback_profile(struct i40e_hw *hw, struct i40e_profile_segment *i40e_seg,
 		      u32 track_id);
-enum i40e_status_code
+int
 i40e_add_pinfo_to_list(struct i40e_hw *hw,
 		       struct i40e_profile_segment *profile,
 		       u8 *profile_info_sec, u32 track_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_ptp.c
@@ -35,7 +35,7 @@
 	GPIO_4
 };
 
-enum i40e_can_set_pins_t {
+enum i40e_can_set_pins {
 	CANT_DO_PINS = -1,
 	CAN_SET_PINS,
 	CAN_DO_PINS
@@ -193,7 +193,7 @@
  * return CAN_DO_PINS if pins can be manipulated within a NIC or
  * return CANT_DO_PINS otherwise.
  **/
-static enum i40e_can_set_pins_t i40e_can_set_pins(struct i40e_pf *pf)
+static enum i40e_can_set_pins i40e_can_set_pins(struct i40e_pf *pf)
 {
 	if (!i40e_is_ptp_pin_dev(&pf->hw)) {
 		dev_warn(&pf->pdev->dev,
@@ -1089,7 +1089,7 @@
 static int i40e_ptp_set_pins(struct i40e_pf *pf,
 			     struct i40e_ptp_pins_settings *pins)
 {
-	enum i40e_can_set_pins_t pin_caps = i40e_can_set_pins(pf);
+	enum i40e_can_set_pins pin_caps = i40e_can_set_pins(pf);
 	int i = 0;
 
 	if (pin_caps == CANT_DO_PINS)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_register.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_register.h
@@ -211,6 +211,11 @@
 #define I40E_GLGEN_MSRWD_MDIWRDATA_SHIFT 0
 #define I40E_GLGEN_MSRWD_MDIRDDATA_SHIFT 16
 #define I40E_GLGEN_MSRWD_MDIRDDATA_MASK I40E_MASK(0xFFFF, I40E_GLGEN_MSRWD_MDIRDDATA_SHIFT)
+#define I40E_GLGEN_PCIFCNCNT                0x001C0AB4 /* Reset: PCIR */
+#define I40E_GLGEN_PCIFCNCNT_PCIPFCNT_SHIFT 0
+#define I40E_GLGEN_PCIFCNCNT_PCIPFCNT_MASK  I40E_MASK(0x1F, I40E_GLGEN_PCIFCNCNT_PCIPFCNT_SHIFT)
+#define I40E_GLGEN_PCIFCNCNT_PCIVFCNT_SHIFT 16
+#define I40E_GLGEN_PCIFCNCNT_PCIVFCNT_MASK  I40E_MASK(0xFF, I40E_GLGEN_PCIFCNCNT_PCIVFCNT_SHIFT)
 #define I40E_GLGEN_RSTAT 0x000B8188 /* Reset: POR */
 #define I40E_GLGEN_RSTAT_DEVSTATE_SHIFT 0
 #define I40E_GLGEN_RSTAT_DEVSTATE_MASK I40E_MASK(0x3, I40E_GLGEN_RSTAT_DEVSTATE_SHIFT)
@@ -323,8 +328,11 @@
 #define I40E_PFINT_DYN_CTLN_ITR_INDX_SHIFT 3
 #define I40E_PFINT_DYN_CTLN_ITR_INDX_MASK I40E_MASK(0x3, I40E_PFINT_DYN_CTLN_ITR_INDX_SHIFT)
 #define I40E_PFINT_DYN_CTLN_INTERVAL_SHIFT 5
+#define I40E_PFINT_DYN_CTLN_INTERVAL_MASK I40E_MASK(0xFFF, I40E_PFINT_DYN_CTLN_INTERVAL_SHIFT)
 #define I40E_PFINT_DYN_CTLN_SW_ITR_INDX_ENA_SHIFT 24
 #define I40E_PFINT_DYN_CTLN_SW_ITR_INDX_ENA_MASK I40E_MASK(0x1, I40E_PFINT_DYN_CTLN_SW_ITR_INDX_ENA_SHIFT)
+#define I40E_PFINT_DYN_CTLN_SW_ITR_INDX_SHIFT 25
+#define I40E_PFINT_DYN_CTLN_SW_ITR_INDX_MASK I40E_MASK(0x3, I40E_PFINT_DYN_CTLN_SW_ITR_INDX_SHIFT)
 #define I40E_PFINT_ICR0 0x00038780 /* Reset: CORER */
 #define I40E_PFINT_ICR0_INTEVENT_SHIFT 0
 #define I40E_PFINT_ICR0_INTEVENT_MASK I40E_MASK(0x1, I40E_PFINT_ICR0_INTEVENT_SHIFT)
@@ -413,6 +421,9 @@
 #define I40E_VFINT_DYN_CTLN(_INTVF) (0x00024800 + ((_INTVF) * 4)) /* _i=0...511 */ /* Reset: VFR */
 #define I40E_VFINT_DYN_CTLN_CLEARPBA_SHIFT 1
 #define I40E_VFINT_DYN_CTLN_CLEARPBA_MASK I40E_MASK(0x1, I40E_VFINT_DYN_CTLN_CLEARPBA_SHIFT)
+#define I40E_VFINT_ICR0_ADMINQ_SHIFT 30
+#define I40E_VFINT_ICR0_ADMINQ_MASK I40E_MASK(0x1, I40E_VFINT_ICR0_ADMINQ_SHIFT)
+#define I40E_VFINT_ICR0_ENA(_VF) (0x0002C000 + ((_VF) * 4)) /* _i=0...127 */ /* Reset: CORER */
 #define I40E_VPINT_AEQCTL(_VF) (0x0002B800 + ((_VF) * 4)) /* _i=0...127 */ /* Reset: CORER */
 #define I40E_VPINT_AEQCTL_MSIX_INDX_SHIFT 0
 #define I40E_VPINT_AEQCTL_ITR_INDX_SHIFT 11
@@ -640,6 +651,14 @@
 #define I40E_VFQF_HKEY1_MAX_INDEX 12
 #define I40E_VFQF_HLUT1(_i, _VF) (0x00220000 + ((_i) * 1024 + (_VF) * 4)) /* _i=0...15, _VF=0...127 */ /* Reset: CORER */
 #define I40E_VFQF_HLUT1_MAX_INDEX 15
+#define I40E_GL_RXERR1H(_i)             (0x00318004 + ((_i) * 8)) /* _i=0...143 */ /* Reset: CORER */
+#define I40E_GL_RXERR1H_MAX_INDEX       143
+#define I40E_GL_RXERR1H_RXERR1H_SHIFT   0
+#define I40E_GL_RXERR1H_RXERR1H_MASK    I40E_MASK(0xFFFFFFFF, I40E_GL_RXERR1H_RXERR1H_SHIFT)
+#define I40E_GL_RXERR1L(_i)             (0x00318000 + ((_i) * 8)) /* _i=0...143 */ /* Reset: CORER */
+#define I40E_GL_RXERR1L_MAX_INDEX       143
+#define I40E_GL_RXERR1L_RXERR1L_SHIFT   0
+#define I40E_GL_RXERR1L_RXERR1L_MASK    I40E_MASK(0xFFFFFFFF, I40E_GL_RXERR1L_RXERR1L_SHIFT)
 #define I40E_GLPRT_BPRCH(_i) (0x003005E4 + ((_i) * 8)) /* _i=0...3 */ /* Reset: CORER */
 #define I40E_GLPRT_BPRCL(_i) (0x003005E0 + ((_i) * 8)) /* _i=0...3 */ /* Reset: CORER */
 #define I40E_GLPRT_BPTCH(_i) (0x00300A04 + ((_i) * 8)) /* _i=0...3 */ /* Reset: CORER */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -170,10 +170,10 @@
 				      struct i40e_fdir_filter *data)
 {
 	bool is_vlan = !!data->vlan_tag;
-	struct vlan_hdr vlan;
-	struct ipv6hdr ipv6;
-	struct ethhdr eth;
-	struct iphdr ip;
+	struct vlan_hdr vlan = {};
+	struct ipv6hdr ipv6 = {};
+	struct ethhdr eth = {};
+	struct iphdr ip = {};
 	u8 *tmp;
 
 	if (ipv4) {
@@ -830,8 +830,6 @@
 	i40e_clean_tx_ring(tx_ring);
 	kfree(tx_ring->tx_bi);
 	tx_ring->tx_bi = NULL;
-	kfree(tx_ring->xsk_descs);
-	tx_ring->xsk_descs = NULL;
 
 	if (tx_ring->desc) {
 		dma_free_coherent(tx_ring->dev, tx_ring->size,
@@ -1433,13 +1431,6 @@
 	if (!tx_ring->tx_bi)
 		goto err;
 
-	if (ring_is_xdp(tx_ring)) {
-		tx_ring->xsk_descs = kcalloc(I40E_MAX_NUM_DESCRIPTORS, sizeof(*tx_ring->xsk_descs),
-					     GFP_KERNEL);
-		if (!tx_ring->xsk_descs)
-			goto err;
-	}
-
 	u64_stats_init(&tx_ring->syncp);
 
 	/* round up to nearest 4K */
@@ -1463,21 +1454,11 @@
 	return 0;
 
 err:
-	kfree(tx_ring->xsk_descs);
-	tx_ring->xsk_descs = NULL;
 	kfree(tx_ring->tx_bi);
 	tx_ring->tx_bi = NULL;
 	return -ENOMEM;
 }
 
-int i40e_alloc_rx_bi(struct i40e_ring *rx_ring)
-{
-	unsigned long sz = sizeof(*rx_ring->rx_bi) * rx_ring->count;
-
-	rx_ring->rx_bi = kzalloc(sz, GFP_KERNEL);
-	return rx_ring->rx_bi ? 0 : -ENOMEM;
-}
-
 static void i40e_clear_rx_bi(struct i40e_ring *rx_ring)
 {
 	memset(rx_ring->rx_bi, 0, sizeof(*rx_ring->rx_bi) * rx_ring->count);
@@ -1608,6 +1589,11 @@
 
 	rx_ring->xdp_prog = rx_ring->vsi->xdp_prog;
 
+	rx_ring->rx_bi =
+		kcalloc(rx_ring->count, sizeof(*rx_ring->rx_bi), GFP_KERNEL);
+	if (!rx_ring->rx_bi)
+		return -ENOMEM;
+
 	return 0;
 }
 
@@ -2574,7 +2560,22 @@
 	return failure ? budget : (int)total_rx_packets;
 }
 
-static inline u32 i40e_buildreg_itr(const int type, u16 itr)
+/**
+ * i40e_buildreg_itr - build a value for writing to I40E_PFINT_DYN_CTLN register
+ * @itr_idx: interrupt throttling index
+ * @interval: interrupt throttling interval value in usecs
+ * @force_swint: force software interrupt
+ *
+ * The function builds a value for I40E_PFINT_DYN_CTLN register that
+ * is used to update interrupt throttling interval for specified ITR index
+ * and optionally enforces a software interrupt. If the @itr_idx is equal
+ * to I40E_ITR_NONE then no interval change is applied and only @force_swint
+ * parameter is taken into account. If the interval change and enforced
+ * software interrupt are not requested then the built value just enables
+ * appropriate vector interrupt.
+ **/
+static u32 i40e_buildreg_itr(enum i40e_dyn_idx itr_idx, u16 interval,
+			     bool force_swint)
 {
 	u32 val;
 
@@ -2588,23 +2589,33 @@
 	 * an event in the PBA anyway so we need to rely on the automask
 	 * to hold pending events for us until the interrupt is re-enabled
 	 *
-	 * The itr value is reported in microseconds, and the register
-	 * value is recorded in 2 microsecond units. For this reason we
-	 * only need to shift by the interval shift - 1 instead of the
-	 * full value.
+	 * We have to shift the given value as it is reported in microseconds
+	 * and the register value is recorded in 2 microsecond units.
 	 */
-	itr &= I40E_ITR_MASK;
+	interval >>= 1;
 
+	/* 1. Enable vector interrupt
+	 * 2. Update the interval for the specified ITR index
+	 *    (I40E_ITR_NONE in the register is used to indicate that
+	 *     no interval update is requested)
+	 */
 	val = I40E_PFINT_DYN_CTLN_INTENA_MASK |
-	      (type << I40E_PFINT_DYN_CTLN_ITR_INDX_SHIFT) |
-	      (itr << (I40E_PFINT_DYN_CTLN_INTERVAL_SHIFT - 1));
+	      FIELD_PREP(I40E_PFINT_DYN_CTLN_ITR_INDX_MASK, itr_idx) |
+	      FIELD_PREP(I40E_PFINT_DYN_CTLN_INTERVAL_MASK, interval);
+
+	/* 3. Enforce software interrupt trigger if requested
+	 *    (These software interrupts rate is limited by ITR2 that is
+	 *     set to 20K interrupts per second)
+	 */
+	if (force_swint)
+		val |= I40E_PFINT_DYN_CTLN_SWINT_TRIG_MASK |
+		       I40E_PFINT_DYN_CTLN_SW_ITR_INDX_ENA_MASK |
+		       FIELD_PREP(I40E_PFINT_DYN_CTLN_SW_ITR_INDX_MASK,
+				  I40E_SW_ITR);
 
 	return val;
 }
 
-/* a small macro to shorten up some long lines */
-#define INTREG I40E_PFINT_DYN_CTLN
-
 /* The act of updating the ITR will cause it to immediately trigger. In order
  * to prevent this from throwing off adaptive update statistics we defer the
  * update so that it can only happen so often. So after either Tx or Rx are
@@ -2623,8 +2634,10 @@
 static inline void i40e_update_enable_itr(struct i40e_vsi *vsi,
 					  struct i40e_q_vector *q_vector)
 {
+	enum i40e_dyn_idx itr_idx = I40E_ITR_NONE;
 	struct i40e_hw *hw = &vsi->back->hw;
-	u32 intval;
+	u16 interval = 0;
+	u32 itr_val;
 
 	/* If we don't have MSIX, then we only need to re-enable icr0 */
 	if (!(vsi->back->flags & I40E_FLAG_MSIX_ENABLED)) {
@@ -2646,8 +2659,8 @@
 	 */
 	if (q_vector->rx.target_itr < q_vector->rx.current_itr) {
 		/* Rx ITR needs to be reduced, this is highest priority */
-		intval = i40e_buildreg_itr(I40E_RX_ITR,
-					   q_vector->rx.target_itr);
+		itr_idx = I40E_RX_ITR;
+		interval = q_vector->rx.target_itr;
 		q_vector->rx.current_itr = q_vector->rx.target_itr;
 		q_vector->itr_countdown = ITR_COUNTDOWN_START;
 	} else if ((q_vector->tx.target_itr < q_vector->tx.current_itr) ||
@@ -2656,25 +2669,36 @@
 		/* Tx ITR needs to be reduced, this is second priority
 		 * Tx ITR needs to be increased more than Rx, fourth priority
 		 */
-		intval = i40e_buildreg_itr(I40E_TX_ITR,
-					   q_vector->tx.target_itr);
+		itr_idx = I40E_TX_ITR;
+		interval = q_vector->tx.target_itr;
 		q_vector->tx.current_itr = q_vector->tx.target_itr;
 		q_vector->itr_countdown = ITR_COUNTDOWN_START;
 	} else if (q_vector->rx.current_itr != q_vector->rx.target_itr) {
 		/* Rx ITR needs to be increased, third priority */
-		intval = i40e_buildreg_itr(I40E_RX_ITR,
-					   q_vector->rx.target_itr);
+		itr_idx = I40E_RX_ITR;
+		interval = q_vector->rx.target_itr;
 		q_vector->rx.current_itr = q_vector->rx.target_itr;
 		q_vector->itr_countdown = ITR_COUNTDOWN_START;
 	} else {
 		/* No ITR update, lowest priority */
-		intval = i40e_buildreg_itr(I40E_ITR_NONE, 0);
 		if (q_vector->itr_countdown)
 			q_vector->itr_countdown--;
 	}
 
-	if (!test_bit(__I40E_VSI_DOWN, vsi->state))
-		wr32(hw, INTREG(q_vector->reg_idx), intval);
+	/* Do not update interrupt control register if VSI is down */
+	if (test_bit(__I40E_VSI_DOWN, vsi->state))
+		return;
+
+	/* Update ITR interval if necessary and enforce software interrupt
+	 * if we are exiting busy poll.
+	 */
+	if (q_vector->in_busy_poll) {
+		itr_val = i40e_buildreg_itr(itr_idx, interval, true);
+		q_vector->in_busy_poll = false;
+	} else {
+		itr_val = i40e_buildreg_itr(itr_idx, interval, false);
+	}
+	wr32(hw, I40E_PFINT_DYN_CTLN(q_vector->reg_idx), itr_val);
 }
 
 /**
@@ -2773,7 +2797,7 @@
 		return budget;
 	}
 
-	if (vsi->back->flags & I40E_TXR_FLAGS_WB_ON_ITR)
+	if (q_vector->tx.ring[0].flags & I40E_TXR_FLAGS_WB_ON_ITR)
 		q_vector->arm_wb_state = false;
 
 	/* Exit the polling mode, but don't re-enable interrupts if stack might
@@ -2781,6 +2805,8 @@
 	 */
 	if (likely(napi_complete_done(napi, work_done)))
 		i40e_update_enable_itr(vsi, q_vector);
+	else
+		q_vector->in_busy_poll = true;
 
 	return min(work_done, budget - 1);
 }
@@ -2989,7 +3015,7 @@
 			rc = skb_cow_head(skb, 0);
 			if (rc < 0)
 				return rc;
-			vhdr = (struct vlan_ethhdr *)skb->data;
+			vhdr = skb_vlan_eth_hdr(skb);
 			vhdr->h_vlan_TCI = htons(tx_flags >>
 						 I40E_TX_FLAGS_VLAN_SHIFT);
 		} else {
@@ -3662,7 +3688,8 @@
 	u8 prio;
 
 	/* is DCB enabled at all? */
-	if (vsi->tc_config.numtc == 1)
+	if (vsi->tc_config.numtc == 1 ||
+	    i40e_is_tc_mqprio_enabled(vsi->back))
 		return netdev_pick_tx(netdev, skb, sb_dev);
 
 	prio = skb->priority;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_txrx.h
@@ -57,7 +57,7 @@
  * mentioning ITR_INDX, ITR_NONE cannot be used as an index 'n' into any
  * register but instead is a special value meaning "don't update" ITR0/1/2.
  */
-enum i40e_dyn_idx_t {
+enum i40e_dyn_idx {
 	I40E_IDX_ITR0 = 0,
 	I40E_IDX_ITR1 = 1,
 	I40E_IDX_ITR2 = 2,
@@ -67,6 +67,7 @@
 /* these are indexes into ITRN registers */
 #define I40E_RX_ITR    I40E_IDX_ITR0
 #define I40E_TX_ITR    I40E_IDX_ITR1
+#define I40E_SW_ITR    I40E_IDX_ITR2
 
 /* Supported RSS offloads */
 #define I40E_DEFAULT_RSS_HENA ( \
@@ -301,7 +302,7 @@
 	u64 realloc_count;
 };
 
-enum i40e_ring_state_t {
+enum i40e_ring_state {
 	__I40E_TX_FDIR_INIT_DONE,
 	__I40E_TX_XPS_INIT_DONE,
 	__I40E_RING_STATE_NBITS /* must be last */
@@ -390,7 +391,6 @@
 	u16 rx_offset;
 	struct xdp_rxq_info xdp_rxq;
 	struct xsk_buff_pool *xsk_pool;
-	struct xdp_desc *xsk_descs;      /* For storing descriptors in the AF_XDP ZC path */
 } ____cacheline_internodealigned_in_smp;
 
 static inline bool ring_uses_build_skb(struct i40e_ring *ring)
@@ -467,7 +467,6 @@
 bool __i40e_chk_linearize(struct sk_buff *skb);
 int i40e_xdp_xmit(struct net_device *dev, int n, struct xdp_frame **frames,
 		  u32 flags);
-int i40e_alloc_rx_bi(struct i40e_ring *rx_ring);
 
 /**
  * i40e_get_head - Retrieve head from head writeback
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_type.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_type.h
@@ -1172,6 +1172,7 @@
 	u64 tx_broadcast;		/* bptc */
 	u64 tx_discards;		/* tdpc */
 	u64 tx_errors;			/* tepc */
+	u64 rx_discards_other;          /* rxerr1 */
 };
 
 /* Statistics collected per VEB per TC */
@@ -1403,6 +1404,10 @@
 #define I40E_PFQF_CTL_0_HASHLUTSIZE_512	0x00010000
 
 /* INPUT SET MASK for RSS, flow director, and flexible payload */
+#define I40E_X722_L3_SRC_SHIFT		49
+#define I40E_X722_L3_SRC_MASK		(0x3ULL << I40E_X722_L3_SRC_SHIFT)
+#define I40E_X722_L3_DST_SHIFT		41
+#define I40E_X722_L3_DST_MASK		(0x3ULL << I40E_X722_L3_DST_SHIFT)
 #define I40E_L3_SRC_SHIFT		47
 #define I40E_L3_SRC_MASK		(0x3ULL << I40E_L3_SRC_SHIFT)
 #define I40E_L3_V6_SRC_SHIFT		43
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
@@ -17,7 +17,7 @@
  **/
 static void i40e_vc_vf_broadcast(struct i40e_pf *pf,
 				 enum virtchnl_ops v_opcode,
-				 i40e_status v_retval, u8 *msg,
+				 int v_retval, u8 *msg,
 				 u16 msglen)
 {
 	struct i40e_hw *hw = &pf->hw;
@@ -152,6 +152,32 @@
 			     (u8 *)&pfe, sizeof(struct virtchnl_pf_event));
 }
 
+#ifdef CONFIG_PCI_IOV
+void i40e_restore_all_vfs_msi_state(struct pci_dev *pdev)
+{
+	u16 vf_id;
+	u16 pos;
+
+	/* Continue only if this is a PF */
+	if (!pdev->is_physfn)
+		return;
+
+	if (!pci_num_vf(pdev))
+		return;
+
+	pos = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_SRIOV);
+	if (pos) {
+		struct pci_dev *vf_dev = NULL;
+
+		pci_read_config_word(pdev, pos + PCI_SRIOV_VF_DID, &vf_id);
+		while ((vf_dev = pci_get_device(pdev->vendor, vf_id, vf_dev))) {
+			if (vf_dev->is_virtfn && vf_dev->physfn == pdev)
+				pci_restore_msi_state(vf_dev);
+		}
+	}
+}
+#endif /* CONFIG_PCI_IOV */
+
 /**
  * i40e_vc_notify_vf_reset
  * @vf: pointer to the VF structure
@@ -183,17 +209,18 @@
 /***********************misc routines*****************************/
 
 /**
- * i40e_vc_disable_vf
+ * i40e_vc_reset_vf
  * @vf: pointer to the VF info
- *
- * Disable the VF through a SW reset.
+ * @notify_vf: notify vf about reset or not
+ * Reset VF handler.
  **/
-static inline void i40e_vc_disable_vf(struct i40e_vf *vf)
+static void i40e_vc_reset_vf(struct i40e_vf *vf, bool notify_vf)
 {
 	struct i40e_pf *pf = vf->pf;
 	int i;
 
-	i40e_vc_notify_vf_reset(vf);
+	if (notify_vf)
+		i40e_vc_notify_vf_reset(vf);
 
 	/* We want to ensure that an actual reset occurs initiated after this
 	 * function was called. However, we do not want to wait forever, so
@@ -211,9 +238,14 @@
 		usleep_range(10000, 20000);
 	}
 
-	dev_warn(&vf->pf->pdev->dev,
-		 "Failed to initiate reset for VF %d after 200 milliseconds\n",
-		 vf->vf_id);
+	if (notify_vf)
+		dev_warn(&vf->pf->pdev->dev,
+			 "Failed to initiate reset for VF %d after 200 milliseconds\n",
+			 vf->vf_id);
+	else
+		dev_dbg(&vf->pf->pdev->dev,
+			"Failed to initiate reset for VF %d after 200 milliseconds\n",
+			vf->vf_id);
 }
 
 /**
@@ -674,14 +706,13 @@
 				    u16 vsi_queue_id,
 				    struct virtchnl_rxq_info *info)
 {
+	u16 pf_queue_id = i40e_vc_get_pf_queue_id(vf, vsi_id, vsi_queue_id);
 	struct i40e_pf *pf = vf->pf;
+	struct i40e_vsi *vsi = pf->vsi[vf->lan_vsi_idx];
 	struct i40e_hw *hw = &pf->hw;
 	struct i40e_hmc_obj_rxq rx_ctx;
-	u16 pf_queue_id;
 	int ret = 0;
 
-	pf_queue_id = i40e_vc_get_pf_queue_id(vf, vsi_id, vsi_queue_id);
-
 	/* clear the context structure first */
 	memset(&rx_ctx, 0, sizeof(struct i40e_hmc_obj_rxq));
 
@@ -719,6 +750,10 @@
 	}
 	rx_ctx.rxmax = info->max_pkt_size;
 
+	/* if port VLAN is configured increase the max packet size */
+	if (vsi->info.pvid)
+		rx_ctx.rxmax += VLAN_HLEN;
+
 	/* enable 32bytes desc always */
 	rx_ctx.dsize = 1;
 
@@ -1237,13 +1272,13 @@
  * @vl: List of VLANs - apply filter for given VLANs
  * @num_vlans: Number of elements in @vl
  **/
-static i40e_status
+static int
 i40e_set_vsi_promisc(struct i40e_vf *vf, u16 seid, bool multi_enable,
 		     bool unicast_enable, s16 *vl, u16 num_vlans)
 {
-	i40e_status aq_ret, aq_tmp = 0;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_hw *hw = &pf->hw;
+	int aq_ret, aq_tmp = 0;
 	int i;
 
 	/* No VLAN to set promisc on, set on VSI */
@@ -1255,9 +1290,9 @@
 			int aq_err = pf->hw.aq.asq_last_status;
 
 			dev_err(&pf->pdev->dev,
-				"VF %d failed to set multicast promiscuous mode err %s aq_err %s\n",
+				"VF %d failed to set multicast promiscuous mode err %d aq_err %s\n",
 				vf->vf_id,
-				i40e_stat_str(&pf->hw, aq_ret),
+				aq_ret,
 				i40e_aq_str(&pf->hw, aq_err));
 
 			return aq_ret;
@@ -1271,9 +1306,9 @@
 			int aq_err = pf->hw.aq.asq_last_status;
 
 			dev_err(&pf->pdev->dev,
-				"VF %d failed to set unicast promiscuous mode err %s aq_err %s\n",
+				"VF %d failed to set unicast promiscuous mode err %d aq_err %s\n",
 				vf->vf_id,
-				i40e_stat_str(&pf->hw, aq_ret),
+				aq_ret,
 				i40e_aq_str(&pf->hw, aq_err));
 		}
 
@@ -1288,9 +1323,9 @@
 			int aq_err = pf->hw.aq.asq_last_status;
 
 			dev_err(&pf->pdev->dev,
-				"VF %d failed to set multicast promiscuous mode err %s aq_err %s\n",
+				"VF %d failed to set multicast promiscuous mode err %d aq_err %s\n",
 				vf->vf_id,
-				i40e_stat_str(&pf->hw, aq_ret),
+				aq_ret,
 				i40e_aq_str(&pf->hw, aq_err));
 
 			if (!aq_tmp)
@@ -1304,9 +1339,9 @@
 			int aq_err = pf->hw.aq.asq_last_status;
 
 			dev_err(&pf->pdev->dev,
-				"VF %d failed to set unicast promiscuous mode err %s aq_err %s\n",
+				"VF %d failed to set unicast promiscuous mode err %d aq_err %s\n",
 				vf->vf_id,
-				i40e_stat_str(&pf->hw, aq_ret),
+				aq_ret,
 				i40e_aq_str(&pf->hw, aq_err));
 
 			if (!aq_tmp)
@@ -1330,13 +1365,13 @@
  * Called from the VF to configure the promiscuous mode of
  * VF vsis and from the VF reset path to reset promiscuous mode.
  **/
-static i40e_status i40e_config_vf_promiscuous_mode(struct i40e_vf *vf,
-						   u16 vsi_id,
-						   bool allmulti,
-						   bool alluni)
+static int i40e_config_vf_promiscuous_mode(struct i40e_vf *vf,
+					   u16 vsi_id,
+					   bool allmulti,
+					   bool alluni)
 {
-	i40e_status aq_ret = I40E_SUCCESS;
 	struct i40e_pf *pf = vf->pf;
+	int aq_ret = I40E_SUCCESS;
 	struct i40e_vsi *vsi;
 	u16 num_vlans;
 	s16 *vl;
@@ -1368,6 +1403,32 @@
 }
 
 /**
+ * i40e_sync_vfr_reset
+ * @hw: pointer to hw struct
+ * @vf_id: VF identifier
+ *
+ * Before trigger hardware reset, we need to know if no other process has
+ * reserved the hardware for any reset operations. This check is done by
+ * examining the status of the RSTAT1 register used to signal the reset.
+ **/
+static int i40e_sync_vfr_reset(struct i40e_hw *hw, int vf_id)
+{
+	u32 reg;
+	int i;
+
+	for (i = 0; i < I40E_VFR_WAIT_COUNT; i++) {
+		reg = rd32(hw, I40E_VFINT_ICR0_ENA(vf_id)) &
+			   I40E_VFINT_ICR0_ADMINQ_MASK;
+		if (reg)
+			return 0;
+
+		usleep_range(100, 200);
+	}
+
+	return -EAGAIN;
+}
+
+/**
  * i40e_trigger_vf_reset
  * @vf: pointer to the VF structure
  * @flr: VFLR was issued or not
@@ -1381,9 +1442,11 @@
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_hw *hw = &pf->hw;
 	u32 reg, reg_idx, bit_idx;
+	bool vf_active;
+	u32 radq;
 
 	/* warn the VF */
-	clear_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states);
+	vf_active = test_and_clear_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states);
 
 	/* Disable VF's configuration API during reset. The flag is re-enabled
 	 * in i40e_alloc_vf_res(), when it's safe again to access VF's VSI.
@@ -1397,7 +1460,19 @@
 	 * just need to clean up, so don't hit the VFRTRIG register.
 	 */
 	if (!flr) {
-		/* reset VF using VPGEN_VFRTRIG reg */
+		/* Sync VFR reset before trigger next one */
+		radq = rd32(hw, I40E_VFINT_ICR0_ENA(vf->vf_id)) &
+			    I40E_VFINT_ICR0_ADMINQ_MASK;
+		if (vf_active && !radq)
+			/* waiting for finish reset by virtual driver */
+			if (i40e_sync_vfr_reset(hw, vf->vf_id))
+				dev_info(&pf->pdev->dev,
+					 "Reset VF %d never finished\n",
+				vf->vf_id);
+
+		/* Reset VF using VPGEN_VFRTRIG reg. It is also setting
+		 * in progress state in rstat1 register.
+		 */
 		reg = rd32(hw, I40E_VPGEN_VFRTRIG(vf->vf_id));
 		reg |= I40E_VPGEN_VFRTRIG_VFSWR_MASK;
 		wr32(hw, I40E_VPGEN_VFRTRIG(vf->vf_id), reg);
@@ -1487,10 +1562,12 @@
 	if (test_bit(__I40E_VF_RESETS_DISABLED, pf->state))
 		return true;
 
-	/* If the VFs have been disabled, this means something else is
-	 * resetting the VF, so we shouldn't continue.
-	 */
-	if (test_and_set_bit(__I40E_VF_DISABLE, pf->state))
+	/* Bail out if VFs are disabled. */
+	if (test_bit(__I40E_VF_DISABLE, pf->state))
+		return true;
+
+	/* If VF is being reset already we don't need to continue. */
+	if (test_and_set_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
 		return true;
 
 	i40e_trigger_vf_reset(vf, flr);
@@ -1527,7 +1604,8 @@
 	i40e_cleanup_reset_vf(vf);
 
 	i40e_flush(hw);
-	clear_bit(__I40E_VF_DISABLE, pf->state);
+	usleep_range(20000, 40000);
+	clear_bit(I40E_VF_STATE_RESETTING, &vf->vf_states);
 
 	return true;
 }
@@ -1548,8 +1626,8 @@
 {
 	struct i40e_hw *hw = &pf->hw;
 	struct i40e_vf *vf;
-	int i, v;
 	u32 reg;
+	int i;
 
 	/* If we don't have any VFs, then there is nothing to reset */
 	if (!pf->num_alloc_vfs)
@@ -1560,8 +1638,11 @@
 		return false;
 
 	/* Begin reset on all VFs at once */
-	for (v = 0; v < pf->num_alloc_vfs; v++)
-		i40e_trigger_vf_reset(&pf->vf[v], flr);
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
+		/* If VF is being reset no need to trigger reset again */
+		if (!test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
+			i40e_trigger_vf_reset(vf, flr);
+	}
 
 	/* HW requires some time to make sure it can flush the FIFO for a VF
 	 * when it resets it. Poll the VPGEN_VFRSTAT register for each VF in
@@ -1569,22 +1650,23 @@
 	 * the VFs using a simple iterator that increments once that VF has
 	 * finished resetting.
 	 */
-	for (i = 0, v = 0; i < 10 && v < pf->num_alloc_vfs; i++) {
+	for (i = 0, vf = &pf->vf[0]; i < 10 && vf < &pf->vf[pf->num_alloc_vfs]; ++i) {
 		usleep_range(10000, 20000);
 
 		/* Check each VF in sequence, beginning with the VF to fail
 		 * the previous check.
 		 */
-		while (v < pf->num_alloc_vfs) {
-			vf = &pf->vf[v];
-			reg = rd32(hw, I40E_VPGEN_VFRSTAT(vf->vf_id));
-			if (!(reg & I40E_VPGEN_VFRSTAT_VFRD_MASK))
-				break;
+		while (vf < &pf->vf[pf->num_alloc_vfs]) {
+			if (!test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states)) {
+				reg = rd32(hw, I40E_VPGEN_VFRSTAT(vf->vf_id));
+				if (!(reg & I40E_VPGEN_VFRSTAT_VFRD_MASK))
+					break;
+			}
 
 			/* If the current VF has finished resetting, move on
 			 * to the next VF in sequence.
 			 */
-			v++;
+			++vf;
 		}
 	}
 
@@ -1594,31 +1676,39 @@
 	/* Display a warning if at least one VF didn't manage to reset in
 	 * time, but continue on with the operation.
 	 */
-	if (v < pf->num_alloc_vfs)
+	if (vf < &pf->vf[pf->num_alloc_vfs])
 		dev_err(&pf->pdev->dev, "VF reset check timeout on VF %d\n",
-			pf->vf[v].vf_id);
+			vf->vf_id);
 	usleep_range(10000, 20000);
 
 	/* Begin disabling all the rings associated with VFs, but do not wait
 	 * between each VF.
 	 */
-	for (v = 0; v < pf->num_alloc_vfs; v++) {
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
 		/* On initial reset, we don't have any queues to disable */
-		if (pf->vf[v].lan_vsi_idx == 0)
+		if (vf->lan_vsi_idx == 0)
+			continue;
+
+		/* If VF is reset in another thread just continue */
+		if (test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
 			continue;
 
-		i40e_vsi_stop_rings_no_wait(pf->vsi[pf->vf[v].lan_vsi_idx]);
+		i40e_vsi_stop_rings_no_wait(pf->vsi[vf->lan_vsi_idx]);
 	}
 
 	/* Now that we've notified HW to disable all of the VF rings, wait
 	 * until they finish.
 	 */
-	for (v = 0; v < pf->num_alloc_vfs; v++) {
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
 		/* On initial reset, we don't have any queues to disable */
-		if (pf->vf[v].lan_vsi_idx == 0)
+		if (vf->lan_vsi_idx == 0)
 			continue;
 
-		i40e_vsi_wait_queues_disabled(pf->vsi[pf->vf[v].lan_vsi_idx]);
+		/* If VF is reset in another thread just continue */
+		if (test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
+			continue;
+
+		i40e_vsi_wait_queues_disabled(pf->vsi[vf->lan_vsi_idx]);
 	}
 
 	/* Hw may need up to 50ms to finish disabling the RX queues. We
@@ -1627,10 +1717,16 @@
 	mdelay(50);
 
 	/* Finish the reset on each VF */
-	for (v = 0; v < pf->num_alloc_vfs; v++)
-		i40e_cleanup_reset_vf(&pf->vf[v]);
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
+		/* If VF is reset in another thread just continue */
+		if (test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
+			continue;
+
+		i40e_cleanup_reset_vf(vf);
+	}
 
 	i40e_flush(hw);
+	usleep_range(20000, 40000);
 	clear_bit(__I40E_VF_DISABLE, pf->state);
 
 	return true;
@@ -1883,7 +1979,7 @@
 	struct i40e_pf *pf;
 	struct i40e_hw *hw;
 	int abs_vf_id;
-	i40e_status aq_ret;
+	int aq_ret;
 
 	/* validate the request */
 	if (!vf || vf->vf_id >= vf->pf->num_alloc_vfs)
@@ -1893,25 +1989,6 @@
 	hw = &pf->hw;
 	abs_vf_id = vf->vf_id + hw->func_caps.vf_base_id;
 
-	/* single place to detect unsuccessful return values */
-	if (v_retval) {
-		vf->num_invalid_msgs++;
-		dev_info(&pf->pdev->dev, "VF %d failed opcode %d, retval: %d\n",
-			 vf->vf_id, v_opcode, v_retval);
-		if (vf->num_invalid_msgs >
-		    I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED) {
-			dev_err(&pf->pdev->dev,
-				"Number of invalid messages exceeded for VF %d\n",
-				vf->vf_id);
-			dev_err(&pf->pdev->dev, "Use PF Control I/F to enable the VF\n");
-			set_bit(I40E_VF_STATE_DISABLED, &vf->vf_states);
-		}
-	} else {
-		vf->num_valid_msgs++;
-		/* reset the invalid counter, if a valid message is received. */
-		vf->num_invalid_msgs = 0;
-	}
-
 	aq_ret = i40e_aq_send_msg_to_vf(hw, abs_vf_id,	v_opcode, v_retval,
 					msg, msglen, NULL);
 	if (aq_ret) {
@@ -1934,12 +2011,38 @@
  **/
 static int i40e_vc_send_resp_to_vf(struct i40e_vf *vf,
 				   enum virtchnl_ops opcode,
-				   i40e_status retval)
+				   int retval)
 {
 	return i40e_vc_send_msg_to_vf(vf, opcode, retval, NULL, 0);
 }
 
 /**
+ * i40e_sync_vf_state
+ * @vf: pointer to the VF info
+ * @state: VF state
+ *
+ * Called from a VF message to synchronize the service with a potential
+ * VF reset state
+ **/
+static bool i40e_sync_vf_state(struct i40e_vf *vf, enum i40e_vf_states state)
+{
+	int i;
+
+	/* When handling some messages, it needs VF state to be set.
+	 * It is possible that this flag is cleared during VF reset,
+	 * so there is a need to wait until the end of the reset to
+	 * handle the request message correctly.
+	 */
+	for (i = 0; i < I40E_VF_STATE_WAIT_COUNT; i++) {
+		if (test_bit(state, &vf->vf_states))
+			return true;
+		usleep_range(10000, 20000);
+	}
+
+	return test_bit(state, &vf->vf_states);
+}
+
+/**
  * i40e_vc_get_version_msg
  * @vf: pointer to the VF info
  * @msg: pointer to the msg buffer
@@ -1983,6 +2086,25 @@
 }
 
 /**
+ * i40e_vc_get_max_frame_size
+ * @vf: pointer to the VF
+ *
+ * Max frame size is determined based on the current port's max frame size and
+ * whether a port VLAN is configured on this VF. The VF is not aware whether
+ * it's in a port VLAN so the PF needs to account for this in max frame size
+ * checks and sending the max frame size to the VF.
+ **/
+static u16 i40e_vc_get_max_frame_size(struct i40e_vf *vf)
+{
+	u16 max_frame_size = vf->pf->hw.phy.link_info.max_frame_size;
+
+	if (vf->port_vlan_id)
+		max_frame_size -= VLAN_HLEN;
+
+	return max_frame_size;
+}
+
+/**
  * i40e_vc_get_vf_resources_msg
  * @vf: pointer to the VF info
  * @msg: pointer to the msg buffer
@@ -1993,13 +2115,13 @@
 {
 	struct virtchnl_vf_resource *vfres = NULL;
 	struct i40e_pf *pf = vf->pf;
-	i40e_status aq_ret = 0;
 	struct i40e_vsi *vsi;
 	int num_vsis = 1;
+	int aq_ret = 0;
 	size_t len = 0;
 	int ret;
 
-	if (!test_bit(I40E_VF_STATE_INIT, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_INIT)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -2083,6 +2205,7 @@
 	vfres->max_vectors = pf->hw.func_caps.num_msix_vectors_vf;
 	vfres->rss_key_size = I40E_HKEY_ARRAY_SIZE;
 	vfres->rss_lut_size = I40E_VF_HLUT_ARRAY_SIZE;
+	vfres->max_mtu = i40e_vc_get_max_frame_size(vf);
 
 	if (vf->lan_vsi_idx) {
 		vfres->vsi_res[0].vsi_id = vf->lan_vsi_id;
@@ -2091,6 +2214,12 @@
 		/* VFs only use TC 0 */
 		vfres->vsi_res[0].qset_handle
 					  = le16_to_cpu(vsi->info.qs_handle[0]);
+		if (!(vf->driver_caps & VIRTCHNL_VF_OFFLOAD_USO) && !vf->pf_set_mac) {
+			spin_lock_bh(&vsi->mac_filter_hash_lock);
+			i40e_del_mac_filter(vsi, vf->default_lan_addr.addr);
+			eth_zero_addr(vf->default_lan_addr.addr);
+			spin_unlock_bh(&vsi->mac_filter_hash_lock);
+		}
 		ether_addr_copy(vfres->vsi_res[0].default_mac_addr,
 				vf->default_lan_addr.addr);
 	}
@@ -2106,20 +2235,6 @@
 }
 
 /**
- * i40e_vc_reset_vf_msg
- * @vf: pointer to the VF info
- *
- * called from the VF to reset itself,
- * unlike other virtchnl messages, PF driver
- * doesn't send the response back to the VF
- **/
-static void i40e_vc_reset_vf_msg(struct i40e_vf *vf)
-{
-	if (test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states))
-		i40e_reset_vf(vf, false);
-}
-
-/**
  * i40e_vc_config_promiscuous_mode_msg
  * @vf: pointer to the VF info
  * @msg: pointer to the msg buffer
@@ -2132,11 +2247,11 @@
 	struct virtchnl_promisc_info *info =
 	    (struct virtchnl_promisc_info *)msg;
 	struct i40e_pf *pf = vf->pf;
-	i40e_status aq_ret = 0;
 	bool allmulti = false;
 	bool alluni = false;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err_out;
 	}
@@ -2217,13 +2332,14 @@
 	struct virtchnl_vsi_queue_config_info *qci =
 	    (struct virtchnl_vsi_queue_config_info *)msg;
 	struct virtchnl_queue_pair_info *qpi;
-	struct i40e_pf *pf = vf->pf;
 	u16 vsi_id, vsi_queue_id = 0;
-	u16 num_qps_all = 0;
-	i40e_status aq_ret = 0;
+	struct i40e_pf *pf = vf->pf;
 	int i, j = 0, idx = 0;
+	struct i40e_vsi *vsi;
+	u16 num_qps_all = 0;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
@@ -2239,7 +2355,7 @@
 	}
 
 	if (vf->adq_enabled) {
-		for (i = 0; i < I40E_MAX_VF_VSI; i++)
+		for (i = 0; i < vf->num_tc; i++)
 			num_qps_all += vf->ch[i].num_qps;
 		if (num_qps_all != qci->num_queue_pairs) {
 			aq_ret = I40E_ERR_PARAM;
@@ -2310,9 +2426,15 @@
 		pf->vsi[vf->lan_vsi_idx]->num_queue_pairs =
 			qci->num_queue_pairs;
 	} else {
-		for (i = 0; i < vf->num_tc; i++)
-			pf->vsi[vf->ch[i].vsi_idx]->num_queue_pairs =
-			       vf->ch[i].num_qps;
+		for (i = 0; i < vf->num_tc; i++) {
+			vsi = pf->vsi[vf->ch[i].vsi_idx];
+			vsi->num_queue_pairs = vf->ch[i].num_qps;
+
+			if (i40e_update_adq_vsi_queues(vsi, i)) {
+				aq_ret = I40E_ERR_CONFIG;
+				goto error_param;
+			}
+		}
 	}
 
 error_param:
@@ -2362,11 +2484,11 @@
 	struct virtchnl_irq_map_info *irqmap_info =
 	    (struct virtchnl_irq_map_info *)msg;
 	struct virtchnl_vector_map *map;
+	int aq_ret = 0;
 	u16 vsi_id;
-	i40e_status aq_ret = 0;
 	int i;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
@@ -2478,9 +2600,17 @@
 	struct virtchnl_queue_select *vqs =
 	    (struct virtchnl_queue_select *)msg;
 	struct i40e_pf *pf = vf->pf;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	int i;
 
+	if (vf->is_disabled_from_host) {
+		aq_ret = -EPERM;
+		dev_info(&pf->pdev->dev,
+			 "Admin has disabled VF %d, will not enable queues\n",
+			 vf->vf_id);
+		goto error_param;
+	}
+
 	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
@@ -2536,9 +2666,9 @@
 	struct virtchnl_queue_select *vqs =
 	    (struct virtchnl_queue_select *)msg;
 	struct i40e_pf *pf = vf->pf;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
@@ -2571,6 +2701,59 @@
 }
 
 /**
+ * i40e_check_enough_queue - find big enough queue number
+ * @vf: pointer to the VF info
+ * @needed: the number of items needed
+ *
+ * Returns the base item index of the queue, or negative for error
+ **/
+static int i40e_check_enough_queue(struct i40e_vf *vf, u16 needed)
+{
+	unsigned int  i, cur_queues, more, pool_size;
+	struct i40e_lump_tracking *pile;
+	struct i40e_pf *pf = vf->pf;
+	struct i40e_vsi *vsi;
+
+	vsi = pf->vsi[vf->lan_vsi_idx];
+	cur_queues = vsi->alloc_queue_pairs;
+
+	/* if current allocated queues are enough for need */
+	if (cur_queues >= needed)
+		return vsi->base_queue;
+
+	pile = pf->qp_pile;
+	if (cur_queues > 0) {
+		/* if the allocated queues are not zero
+		 * just check if there are enough queues for more
+		 * behind the allocated queues.
+		 */
+		more = needed - cur_queues;
+		for (i = vsi->base_queue + cur_queues;
+			i < pile->num_entries; i++) {
+			if (pile->list[i] & I40E_PILE_VALID_BIT)
+				break;
+
+			if (more-- == 1)
+				/* there is enough */
+				return vsi->base_queue;
+		}
+	}
+
+	pool_size = 0;
+	for (i = 0; i < pile->num_entries; i++) {
+		if (pile->list[i] & I40E_PILE_VALID_BIT) {
+			pool_size = 0;
+			continue;
+		}
+		if (needed <= ++pool_size)
+			/* there is enough */
+			return i;
+	}
+
+	return -ENOMEM;
+}
+
+/**
  * i40e_vc_request_queues_msg
  * @vf: pointer to the VF info
  * @msg: pointer to the msg buffer
@@ -2588,7 +2771,7 @@
 	u8 cur_pairs = vf->num_queue_pairs;
 	struct i40e_pf *pf = vf->pf;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states))
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE))
 		return -EINVAL;
 
 	if (req_pairs > I40E_MAX_VF_QUEUES) {
@@ -2604,11 +2787,16 @@
 			 req_pairs - cur_pairs,
 			 pf->queues_left);
 		vfres->num_queue_pairs = pf->queues_left + cur_pairs;
+	} else if (i40e_check_enough_queue(vf, req_pairs) < 0) {
+		dev_warn(&pf->pdev->dev,
+			 "VF %d requested %d more queues, but there is not enough for it.\n",
+			 vf->vf_id,
+			 req_pairs - cur_pairs);
+		vfres->num_queue_pairs = cur_pairs;
 	} else {
 		/* successful request */
 		vf->num_req_queues = req_pairs;
-		i40e_vc_notify_vf_reset(vf);
-		i40e_reset_vf(vf, false);
+		i40e_vc_reset_vf(vf, true);
 		return 0;
 	}
 
@@ -2629,12 +2817,12 @@
 	    (struct virtchnl_queue_select *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_eth_stats stats;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	struct i40e_vsi *vsi;
 
 	memset(&stats, 0, sizeof(struct i40e_eth_stats));
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
@@ -2658,6 +2846,24 @@
 				      (u8 *)&stats, sizeof(stats));
 }
 
+/**
+ * i40e_can_vf_change_mac
+ * @vf: pointer to the VF info
+ *
+ * Return true if the VF is allowed to change its MAC filters, false otherwise
+ */
+static bool i40e_can_vf_change_mac(struct i40e_vf *vf)
+{
+	/* If the VF MAC address has been set administratively (via the
+	 * ndo_set_vf_mac command), then deny permission to the VF to
+	 * add/delete unicast MAC addresses, unless the VF is trusted
+	 */
+	if (vf->pf_set_mac && !vf->trusted)
+		return false;
+
+	return true;
+}
+
 /* If the VF is not trusted restrict the number of MAC/VLAN it can program
  * MAC filters: 16 for multicast, 1 for MAC, 1 for broadcast
  */
@@ -2707,8 +2913,8 @@
 		 * The VF may request to set the MAC address filter already
 		 * assigned to it so do not return an error in that case.
 		 */
-		if (!test_bit(I40E_VIRTCHNL_VF_CAP_PRIVILEGE, &vf->vf_caps) &&
-		    !is_multicast_ether_addr(addr) && vf->pf_set_mac &&
+		if (!i40e_can_vf_change_mac(vf) &&
+		    !is_multicast_ether_addr(addr) &&
 		    !ether_addr_equal(addr, vf->default_lan_addr.addr)) {
 			dev_err(&pf->pdev->dev,
 				"VF attempting to override administratively set MAC address, bring down and up the VF interface to resume normal operation\n");
@@ -2748,10 +2954,10 @@
 	    (struct virtchnl_ether_addr_list *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status ret = 0;
+	int ret = 0;
 	int i;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE) ||
 	    !i40e_vc_isvalid_vsi_id(vf, al->vsi_id)) {
 		ret = I40E_ERR_PARAM;
 		goto error_param;
@@ -2802,8 +3008,8 @@
 
 error_param:
 	/* send the response to the VF */
-	return i40e_vc_send_resp_to_vf(vf, VIRTCHNL_OP_ADD_ETH_ADDR,
-				       ret);
+	return i40e_vc_send_msg_to_vf(vf, VIRTCHNL_OP_ADD_ETH_ADDR,
+				      ret, NULL, 0);
 }
 
 /**
@@ -2820,10 +3026,10 @@
 	bool was_unimac_deleted = false;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status ret = 0;
+	int ret = 0;
 	int i;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE) ||
 	    !i40e_vc_isvalid_vsi_id(vf, al->vsi_id)) {
 		ret = I40E_ERR_PARAM;
 		goto error_param;
@@ -2837,19 +3043,29 @@
 			ret = I40E_ERR_INVALID_MAC_ADDR;
 			goto error_param;
 		}
-		if (ether_addr_equal(al->list[i].addr, vf->default_lan_addr.addr))
-			was_unimac_deleted = true;
 	}
 	vsi = pf->vsi[vf->lan_vsi_idx];
 
 	spin_lock_bh(&vsi->mac_filter_hash_lock);
 	/* delete addresses from the list */
-	for (i = 0; i < al->num_elements; i++)
+	for (i = 0; i < al->num_elements; i++) {
+		const u8 *addr = al->list[i].addr;
+
+		/* Allow to delete VF primary MAC only if it was not set
+		 * administratively by PF or if VF is trusted.
+		 */
+		if (ether_addr_equal(addr, vf->default_lan_addr.addr) &&
+		    i40e_can_vf_change_mac(vf))
+			was_unimac_deleted = true;
+		else
+			continue;
+
 		if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
 			ret = I40E_ERR_INVALID_MAC_ADDR;
 			spin_unlock_bh(&vsi->mac_filter_hash_lock);
 			goto error_param;
 		}
+	}
 
 	spin_unlock_bh(&vsi->mac_filter_hash_lock);
 
@@ -2893,7 +3109,7 @@
 	    (struct virtchnl_vlan_filter_list *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	int i;
 
 	if ((vf->num_vlan >= I40E_VC_MAX_VLAN_PER_VF) &&
@@ -2964,10 +3180,10 @@
 	    (struct virtchnl_vlan_filter_list *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	int i;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE) ||
 	    !i40e_vc_isvalid_vsi_id(vf, vfl->vsi_id)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
@@ -3020,7 +3236,7 @@
 {
 	struct i40e_pf *pf = vf->pf;
 	int abs_vf_id = vf->vf_id + pf->hw.func_caps.vf_base_id;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 
 	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
 	    !test_bit(I40E_VF_STATE_IWARPENA, &vf->vf_states)) {
@@ -3049,7 +3265,7 @@
 {
 	struct virtchnl_iwarp_qvlist_info *qvlist_info =
 				(struct virtchnl_iwarp_qvlist_info *)msg;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 
 	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
 	    !test_bit(I40E_VF_STATE_IWARPENA, &vf->vf_states)) {
@@ -3085,11 +3301,11 @@
 		(struct virtchnl_rss_key *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE) ||
 	    !i40e_vc_isvalid_vsi_id(vf, vrk->vsi_id) ||
-	    (vrk->key_len != I40E_HKEY_ARRAY_SIZE)) {
+	    vrk->key_len != I40E_HKEY_ARRAY_SIZE) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3115,12 +3331,12 @@
 		(struct virtchnl_rss_lut *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	u16 i;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states) ||
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE) ||
 	    !i40e_vc_isvalid_vsi_id(vf, vrl->vsi_id) ||
-	    (vrl->lut_entries != I40E_VF_HLUT_ARRAY_SIZE)) {
+	    vrl->lut_entries != I40E_VF_HLUT_ARRAY_SIZE) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3150,10 +3366,10 @@
 {
 	struct virtchnl_rss_hena *vrh = NULL;
 	struct i40e_pf *pf = vf->pf;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	int len = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3187,9 +3403,9 @@
 		(struct virtchnl_rss_hena *)msg;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_hw *hw = &pf->hw;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3211,10 +3427,10 @@
  **/
 static int i40e_vc_enable_vlan_stripping(struct i40e_vf *vf, u8 *msg)
 {
-	i40e_status aq_ret = 0;
 	struct i40e_vsi *vsi;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3237,10 +3453,10 @@
  **/
 static int i40e_vc_disable_vlan_stripping(struct i40e_vf *vf, u8 *msg)
 {
-	i40e_status aq_ret = 0;
 	struct i40e_vsi *vsi;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3273,16 +3489,16 @@
 	bool found = false;
 	int bkt;
 
-	if (!tc_filter->action) {
+	if (tc_filter->action != VIRTCHNL_ACTION_TC_REDIRECT) {
 		dev_info(&pf->pdev->dev,
-			 "VF %d: Currently ADq doesn't support Drop Action\n",
-			 vf->vf_id);
+			 "VF %d: ADQ doesn't support this action (%d)\n",
+			 vf->vf_id, tc_filter->action);
 		goto err;
 	}
 
 	/* action_meta is TC number here to which the filter is applied */
 	if (!tc_filter->action_meta ||
-	    tc_filter->action_meta > I40E_MAX_VF_VSI) {
+	    tc_filter->action_meta > vf->num_tc) {
 		dev_info(&pf->pdev->dev, "VF %d: Invalid TC number %u\n",
 			 vf->vf_id, tc_filter->action_meta);
 		goto err;
@@ -3437,8 +3653,8 @@
 			ret = i40e_add_del_cloud_filter(vsi, cfilter, false);
 		if (ret)
 			dev_err(&pf->pdev->dev,
-				"VF %d: Failed to delete cloud filter, err %s aq_err %s\n",
-				vf->vf_id, i40e_stat_str(&pf->hw, ret),
+				"VF %d: Failed to delete cloud filter, err %d aq_err %s\n",
+				vf->vf_id, ret,
 				i40e_aq_str(&pf->hw,
 					    pf->hw.aq.asq_last_status));
 
@@ -3464,10 +3680,10 @@
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
 	struct hlist_node *node;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	int i, ret;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3540,8 +3756,8 @@
 		ret = i40e_add_del_cloud_filter(vsi, &cfilter, false);
 	if (ret) {
 		dev_err(&pf->pdev->dev,
-			"VF %d: Failed to delete cloud filter, err %s aq_err %s\n",
-			vf->vf_id, i40e_stat_str(&pf->hw, ret),
+			"VF %d: Failed to delete cloud filter, err %d aq_err %s\n",
+			vf->vf_id, ret,
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto err;
 	}
@@ -3595,10 +3811,10 @@
 	struct i40e_cloud_filter *cfilter = NULL;
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_vsi *vsi = NULL;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	int i, ret;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err_out;
 	}
@@ -3674,8 +3890,8 @@
 		ret = i40e_add_del_cloud_filter(vsi, cfilter, true);
 	if (ret) {
 		dev_err(&pf->pdev->dev,
-			"VF %d: Failed to add cloud filter, err %s aq_err %s\n",
-			vf->vf_id, i40e_stat_str(&pf->hw, ret),
+			"VF %d: Failed to add cloud filter, err %d aq_err %s\n",
+			vf->vf_id, ret,
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 		goto err_free;
 	}
@@ -3704,10 +3920,10 @@
 	struct i40e_pf *pf = vf->pf;
 	struct i40e_link_status *ls = &pf->hw.phy.link_info;
 	int i, adq_request_qps = 0;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 	u64 speed = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3796,15 +4012,9 @@
 
 	/* set this flag only after making sure all inputs are sane */
 	vf->adq_enabled = true;
-	/* num_req_queues is set when user changes number of queues via ethtool
-	 * and this causes issue for default VSI(which depends on this variable)
-	 * when ADq is enabled, hence reset it.
-	 */
-	vf->num_req_queues = 0;
 
 	/* reset the VF in order to allocate resources */
-	i40e_vc_notify_vf_reset(vf);
-	i40e_reset_vf(vf, false);
+	i40e_vc_reset_vf(vf, true);
 
 	return I40E_SUCCESS;
 
@@ -3822,9 +4032,9 @@
 static int i40e_vc_del_qch_msg(struct i40e_vf *vf, u8 *msg)
 {
 	struct i40e_pf *pf = vf->pf;
-	i40e_status aq_ret = 0;
+	int aq_ret = 0;
 
-	if (!test_bit(I40E_VF_STATE_ACTIVE, &vf->vf_states)) {
+	if (!i40e_sync_vf_state(vf, I40E_VF_STATE_ACTIVE)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto err;
 	}
@@ -3844,8 +4054,7 @@
 	}
 
 	/* reset the VF in order to allocate resources */
-	i40e_vc_notify_vf_reset(vf);
-	i40e_reset_vf(vf, false);
+	i40e_vc_reset_vf(vf, true);
 
 	return I40E_SUCCESS;
 
@@ -3907,7 +4116,7 @@
 		i40e_vc_notify_vf_link_state(vf);
 		break;
 	case VIRTCHNL_OP_RESET_VF:
-		i40e_vc_reset_vf_msg(vf);
+		i40e_vc_reset_vf(vf, false);
 		ret = 0;
 		break;
 	case VIRTCHNL_OP_CONFIG_PROMISCUOUS_MODE:
@@ -4161,7 +4370,7 @@
 	/* Force the VF interface down so it has to bring up with new MAC
 	 * address
 	 */
-	i40e_vc_disable_vf(vf);
+	i40e_vc_reset_vf(vf, true);
 	dev_info(&pf->pdev->dev, "Bring down and up the VF interface to make this change effective.\n");
 
 error_param:
@@ -4170,34 +4379,6 @@
 }
 
 /**
- * i40e_vsi_has_vlans - True if VSI has configured VLANs
- * @vsi: pointer to the vsi
- *
- * Check if a VSI has configured any VLANs. False if we have a port VLAN or if
- * we have no configured VLANs. Do not call while holding the
- * mac_filter_hash_lock.
- */
-static bool i40e_vsi_has_vlans(struct i40e_vsi *vsi)
-{
-	bool have_vlans;
-
-	/* If we have a port VLAN, then the VSI cannot have any VLANs
-	 * configured, as all MAC/VLAN filters will be assigned to the PVID.
-	 */
-	if (vsi->info.pvid)
-		return false;
-
-	/* Since we don't have a PVID, we know that if the device is in VLAN
-	 * mode it must be because of a VLAN filter configured on this VSI.
-	 */
-	spin_lock_bh(&vsi->mac_filter_hash_lock);
-	have_vlans = i40e_is_vsi_in_vlan(vsi);
-	spin_unlock_bh(&vsi->mac_filter_hash_lock);
-
-	return have_vlans;
-}
-
-/**
  * i40e_ndo_set_vf_port_vlan
  * @netdev: network interface device structure
  * @vf_id: VF identifier
@@ -4253,18 +4434,7 @@
 		/* duplicate request, so just return success */
 		goto error_pvid;
 
-	if (i40e_vsi_has_vlans(vsi)) {
-		dev_err(&pf->pdev->dev,
-			"VF %d has already configured VLAN filters and the administrator is requesting a port VLAN override.\nPlease unload and reload the VF driver for this change to take effect.\n",
-			vf_id);
-		/* Administrator Error - knock the VF offline until he does
-		 * the right thing by reconfiguring his network correctly
-		 * and then reloading the VF driver.
-		 */
-		i40e_vc_disable_vf(vf);
-		/* During reset the VF got a new VSI, so refresh the pointer. */
-		vsi = pf->vsi[vf->lan_vsi_idx];
-	}
+	i40e_vlan_stripping_enable(vsi);
 
 	/* Locked once because multiple functions below iterate list */
 	spin_lock_bh(&vsi->mac_filter_hash_lock);
@@ -4278,7 +4448,7 @@
 	 * MAC addresses deleted.
 	 */
 	if ((!(vlan_id || qos) ||
-	    vlanprio != le16_to_cpu(vsi->info.pvid)) &&
+	     vlanprio != le16_to_cpu(vsi->info.pvid)) &&
 	    vsi->info.pvid) {
 		ret = i40e_add_vlan_all_mac(vsi, I40E_VLAN_ANY);
 		if (ret) {
@@ -4351,6 +4521,10 @@
 	 */
 	vf->port_vlan_id = le16_to_cpu(vsi->info.pvid);
 
+	i40e_vc_reset_vf(vf, true);
+	/* During reset the VF got a new VSI, so refresh a pointer. */
+	vsi = pf->vsi[vf->lan_vsi_idx];
+
 	ret = i40e_config_vf_promiscuous_mode(vf, vsi->id, allmulti, alluni);
 	if (ret) {
 		dev_err(&pf->pdev->dev, "Unable to config vf promiscuous mode\n");
@@ -4492,9 +4666,12 @@
 	struct i40e_link_status *ls = &pf->hw.phy.link_info;
 	struct virtchnl_pf_event pfe;
 	struct i40e_hw *hw = &pf->hw;
+	struct i40e_vsi *vsi;
+	unsigned long q_map;
 	struct i40e_vf *vf;
 	int abs_vf_id;
 	int ret = 0;
+	int tmp;
 
 	if (test_and_set_bit(__I40E_VIRTCHNL_OP_PENDING, pf->state)) {
 		dev_warn(&pf->pdev->dev, "Unable to configure VFs, other operation is pending.\n");
@@ -4517,17 +4694,38 @@
 	switch (link) {
 	case IFLA_VF_LINK_STATE_AUTO:
 		vf->link_forced = false;
+		vf->is_disabled_from_host = false;
+		/* reset needed to reinit VF resources */
+		i40e_vc_reset_vf(vf, true);
 		i40e_set_vf_link_state(vf, &pfe, ls);
 		break;
 	case IFLA_VF_LINK_STATE_ENABLE:
 		vf->link_forced = true;
 		vf->link_up = true;
+		vf->is_disabled_from_host = false;
+		/* reset needed to reinit VF resources */
+		i40e_vc_reset_vf(vf, true);
 		i40e_set_vf_link_state(vf, &pfe, ls);
 		break;
 	case IFLA_VF_LINK_STATE_DISABLE:
 		vf->link_forced = true;
 		vf->link_up = false;
 		i40e_set_vf_link_state(vf, &pfe, ls);
+
+		vsi = pf->vsi[vf->lan_vsi_idx];
+		q_map = BIT(vsi->num_queue_pairs) - 1;
+
+		vf->is_disabled_from_host = true;
+
+		/* Try to stop both Tx&Rx rings even if one of the calls fails
+		 * to ensure we stop the rings even in case of errors.
+		 * If any of them returns with an error then the first
+		 * error that occurred will be returned.
+		 */
+		tmp = i40e_ctrl_vf_tx_rings(vsi, q_map, false);
+		ret = i40e_ctrl_vf_rx_rings(vsi, q_map, false);
+
+		ret = tmp ? tmp : ret;
 		break;
 	default:
 		ret = -EINVAL;
@@ -4641,7 +4839,12 @@
 		goto out;
 
 	vf->trusted = setting;
-	i40e_vc_disable_vf(vf);
+
+	/* request PF to sync mac/vlan filters for the VF */
+	set_bit(__I40E_MACVLAN_SYNC_PENDING, pf->state);
+	pf->vsi[vf->lan_vsi_idx]->flags |= I40E_VSI_FLAG_FILTER_CHANGED;
+
+	i40e_vc_reset_vf(vf, true);
 	dev_info(&pf->pdev->dev, "VF %u is now %strusted\n",
 		 vf_id, setting ? "" : "un");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.h
@@ -10,14 +10,15 @@
 
 #define I40E_VIRTCHNL_SUPPORTED_QTYPES 2
 
-#define I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED	10
-
 #define I40E_VLAN_PRIORITY_SHIFT	13
 #define I40E_VLAN_MASK			0xFFF
 #define I40E_PRIORITY_MASK		0xE000
 
 #define I40E_MAX_VF_PROMISC_FLAGS	3
 
+#define I40E_VF_STATE_WAIT_COUNT	20
+#define I40E_VFR_WAIT_COUNT		100
+
 /* Various queue ctrls */
 enum i40e_queue_ctrl {
 	I40E_QUEUE_CTRL_UNKNOWN = 0,
@@ -38,6 +39,7 @@
 	I40E_VF_STATE_MC_PROMISC,
 	I40E_VF_STATE_UC_PROMISC,
 	I40E_VF_STATE_PRE_ENABLE,
+	I40E_VF_STATE_RESETTING
 };
 
 /* VF capabilities */
@@ -89,9 +91,6 @@
 	u8 num_queue_pairs;	/* num of qps assigned to VF vsis */
 	u8 num_req_queues;	/* num of requested qps */
 	u64 num_mdd_events;	/* num of mdd events detected */
-	/* num of continuous malformed or invalid msgs detected */
-	u64 num_invalid_msgs;
-	u64 num_valid_msgs;	/* num of valid msgs detected */
 
 	unsigned long vf_caps;	/* vf's adv. capabilities */
 	unsigned long vf_states;	/* vf's runtime states */
@@ -99,6 +98,7 @@
 	bool link_forced;
 	bool link_up;		/* only valid if VF link is forced */
 	bool spoofchk;
+	bool is_disabled_from_host; /* PF ctrl of VF enable/disable */
 	u16 num_vlan;
 
 	/* ADq related variables */
@@ -136,6 +136,9 @@
 
 void i40e_vc_notify_link_state(struct i40e_pf *pf);
 void i40e_vc_notify_reset(struct i40e_pf *pf);
+#ifdef CONFIG_PCI_IOV
+void i40e_restore_all_vfs_msi_state(struct pci_dev *pdev);
+#endif /* CONFIG_PCI_IOV */
 int i40e_get_vf_stats(struct net_device *netdev, int vf_id,
 		      struct ifla_vf_stats *vf_stats);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_xsk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_xsk.c
@@ -10,14 +10,6 @@
 #include "i40e_txrx_common.h"
 #include "i40e_xsk.h"
 
-int i40e_alloc_rx_bi_zc(struct i40e_ring *rx_ring)
-{
-	unsigned long sz = sizeof(*rx_ring->rx_bi_zc) * rx_ring->count;
-
-	rx_ring->rx_bi_zc = kzalloc(sz, GFP_KERNEL);
-	return rx_ring->rx_bi_zc ? 0 : -ENOMEM;
-}
-
 void i40e_clear_rx_bi_zc(struct i40e_ring *rx_ring)
 {
 	memset(rx_ring->rx_bi_zc, 0,
@@ -30,6 +22,58 @@
 }
 
 /**
+ * i40e_realloc_rx_xdp_bi - reallocate SW ring for either XSK or normal buffer
+ * @rx_ring: Current rx ring
+ * @pool_present: is pool for XSK present
+ *
+ * Try allocating memory and return ENOMEM, if failed to allocate.
+ * If allocation was successful, substitute buffer with allocated one.
+ * Returns 0 on success, negative on failure
+ */
+static int i40e_realloc_rx_xdp_bi(struct i40e_ring *rx_ring, bool pool_present)
+{
+	size_t elem_size = pool_present ? sizeof(*rx_ring->rx_bi_zc) :
+					  sizeof(*rx_ring->rx_bi);
+	void *sw_ring = kcalloc(rx_ring->count, elem_size, GFP_KERNEL);
+
+	if (!sw_ring)
+		return -ENOMEM;
+
+	if (pool_present) {
+		kfree(rx_ring->rx_bi);
+		rx_ring->rx_bi = NULL;
+		rx_ring->rx_bi_zc = sw_ring;
+	} else {
+		kfree(rx_ring->rx_bi_zc);
+		rx_ring->rx_bi_zc = NULL;
+		rx_ring->rx_bi = sw_ring;
+	}
+	return 0;
+}
+
+/**
+ * i40e_realloc_rx_bi_zc - reallocate rx SW rings
+ * @vsi: Current VSI
+ * @zc: is zero copy set
+ *
+ * Reallocate buffer for rx_rings that might be used by XSK.
+ * XDP requires more memory, than rx_buf provides.
+ * Returns 0 on success, negative on failure
+ */
+int i40e_realloc_rx_bi_zc(struct i40e_vsi *vsi, bool zc)
+{
+	struct i40e_ring *rx_ring;
+	unsigned long q;
+
+	for_each_set_bit(q, vsi->af_xdp_zc_qps, vsi->alloc_queue_pairs) {
+		rx_ring = vsi->rx_rings[q];
+		if (i40e_realloc_rx_xdp_bi(rx_ring, zc))
+			return -ENOMEM;
+	}
+	return 0;
+}
+
+/**
  * i40e_xsk_pool_enable - Enable/associate an AF_XDP buffer pool to a
  * certain ring/qid
  * @vsi: Current VSI
@@ -69,6 +113,10 @@
 		if (err)
 			return err;
 
+		err = i40e_realloc_rx_xdp_bi(vsi->rx_rings[qid], true);
+		if (err)
+			return err;
+
 		err = i40e_queue_pair_enable(vsi, qid);
 		if (err)
 			return err;
@@ -113,6 +161,9 @@
 	xsk_pool_dma_unmap(pool, I40E_RX_DMA_ATTR);
 
 	if (if_running) {
+		err = i40e_realloc_rx_xdp_bi(vsi->rx_rings[qid], false);
+		if (err)
+			return err;
 		err = i40e_queue_pair_enable(vsi, qid);
 		if (err)
 			return err;
@@ -243,21 +294,25 @@
 static struct sk_buff *i40e_construct_skb_zc(struct i40e_ring *rx_ring,
 					     struct xdp_buff *xdp)
 {
+	unsigned int totalsize = xdp->data_end - xdp->data_meta;
 	unsigned int metasize = xdp->data - xdp->data_meta;
-	unsigned int datasize = xdp->data_end - xdp->data;
 	struct sk_buff *skb;
 
+	net_prefetch(xdp->data_meta);
+
 	/* allocate a skb to store the frags */
-	skb = __napi_alloc_skb(&rx_ring->q_vector->napi,
-			       xdp->data_end - xdp->data_hard_start,
+	skb = __napi_alloc_skb(&rx_ring->q_vector->napi, totalsize,
 			       GFP_ATOMIC | __GFP_NOWARN);
 	if (unlikely(!skb))
 		goto out;
 
-	skb_reserve(skb, xdp->data - xdp->data_hard_start);
-	memcpy(__skb_put(skb, datasize), xdp->data, datasize);
-	if (metasize)
+	memcpy(__skb_put(skb, totalsize), xdp->data_meta,
+	       ALIGN(totalsize, sizeof(long)));
+
+	if (metasize) {
 		skb_metadata_set(skb, metasize);
+		__skb_pull(skb, metasize);
+	}
 
 out:
 	xsk_buff_free(xdp);
@@ -469,11 +524,11 @@
  **/
 static bool i40e_xmit_zc(struct i40e_ring *xdp_ring, unsigned int budget)
 {
-	struct xdp_desc *descs = xdp_ring->xsk_descs;
+	struct xdp_desc *descs = xdp_ring->xsk_pool->tx_descs;
 	u32 nb_pkts, nb_processed = 0;
 	unsigned int total_bytes = 0;
 
-	nb_pkts = xsk_tx_peek_release_desc_batch(xdp_ring->xsk_pool, descs, budget);
+	nb_pkts = xsk_tx_peek_release_desc_batch(xdp_ring->xsk_pool, budget);
 	if (!nb_pkts)
 		return true;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/i40e/i40e_xsk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/i40e/i40e_xsk.h
@@ -33,7 +33,7 @@
 
 bool i40e_clean_xdp_tx_irq(struct i40e_vsi *vsi, struct i40e_ring *tx_ring);
 int i40e_xsk_wakeup(struct net_device *dev, u32 queue_id, u32 flags);
-int i40e_alloc_rx_bi_zc(struct i40e_ring *rx_ring);
+int i40e_realloc_rx_bi_zc(struct i40e_vsi *vsi, bool zc);
 void i40e_clear_rx_bi_zc(struct i40e_ring *rx_ring);
 
 #endif /* _I40E_XSK_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf.h
@@ -39,6 +39,7 @@
 #include "iavf_txrx.h"
 #include "iavf_fdir.h"
 #include "iavf_adv_rss.h"
+#include <linux/bitmap.h>
 
 #define DEFAULT_DEBUG_LEVEL_SHIFT 3
 #define PFX "iavf: "
@@ -88,6 +89,7 @@
 #define IAVF_HKEY_ARRAY_SIZE ((IAVF_VFQF_HKEY_MAX_INDEX + 1) * 4)
 #define IAVF_HLUT_ARRAY_SIZE ((IAVF_VFQF_HLUT_MAX_INDEX + 1) * 4)
 #define IAVF_MBPS_DIVISOR	125000 /* divisor to convert to Mbps */
+#define IAVF_MBPS_QUANTA	50
 
 #define IAVF_VIRTCHNL_VF_RESOURCE_SIZE (sizeof(struct virtchnl_vf_resource) + \
 					(IAVF_MAX_VF_VSI * \
@@ -177,6 +179,7 @@
 	__IAVF_INIT_VERSION_CHECK,	/* aq msg sent, awaiting reply */
 	__IAVF_INIT_GET_RESOURCES,	/* aq msg sent, awaiting reply */
 	__IAVF_INIT_SW,		/* got resources, setting up structs */
+	__IAVF_INIT_FAILED,	/* init failed, restarting procedure */
 	__IAVF_RESETTING,		/* in reset */
 	__IAVF_COMM_FAILED,		/* communication with PF failed */
 	/* Below here, watchdog is running */
@@ -186,6 +189,10 @@
 	__IAVF_RUNNING,		/* opened, working */
 };
 
+enum iavf_critical_section_t {
+	__IAVF_IN_REMOVE_TASK,	/* device being removed */
+};
+
 #define IAVF_CLOUD_FIELD_OMAC		0x01
 #define IAVF_CLOUD_FIELD_IMAC		0x02
 #define IAVF_CLOUD_FIELD_IVLAN	0x04
@@ -225,14 +232,12 @@
 	struct work_struct reset_task;
 	struct work_struct adminq_task;
 	struct delayed_work client_task;
-	struct delayed_work init_task;
 	wait_queue_head_t down_waitqueue;
 	struct iavf_q_vector *q_vectors;
 	struct list_head vlan_filter_list;
 	struct list_head mac_filter_list;
 	struct mutex crit_lock;
 	struct mutex client_lock;
-	struct mutex remove_lock;
 	/* Lock to protect accesses to MAC and VLAN lists */
 	spinlock_t mac_vlan_list_lock;
 	char misc_vector_name[IFNAMSIZ + 9];
@@ -270,6 +275,7 @@
 #define IAVF_FLAG_LEGACY_RX			BIT(15)
 #define IAVF_FLAG_REINIT_ITR_NEEDED		BIT(16)
 #define IAVF_FLAG_QUEUES_DISABLED		BIT(17)
+#define IAVF_FLAG_SETUP_NETDEV_FEATURES		BIT(18)
 /* duplicates for common code */
 #define IAVF_FLAG_DCB_ENABLED			0
 	/* flags for admin queue service task */
@@ -304,6 +310,7 @@
 #define IAVF_FLAG_AQ_DEL_FDIR_FILTER		BIT(26)
 #define IAVF_FLAG_AQ_ADD_ADV_RSS_CFG		BIT(27)
 #define IAVF_FLAG_AQ_DEL_ADV_RSS_CFG		BIT(28)
+#define IAVF_FLAG_AQ_REQUEST_STATS		BIT(29)
 
 	/* OS defined structs */
 	struct net_device *netdev;
@@ -312,6 +319,7 @@
 	struct iavf_hw hw; /* defined in iavf_type.h */
 
 	enum iavf_state_t state;
+	enum iavf_state_t last_state;
 	unsigned long crit_section;
 
 	struct delayed_work watchdog_task;
@@ -370,6 +378,11 @@
 	/* lock to protect access to the cloud filter list */
 	spinlock_t cloud_filter_list_lock;
 	u16 num_cloud_filters;
+	/* snapshot of "num_active_queues" before setup_tc for qdisc add
+	 * is invoked. This information is useful during qdisc del flow,
+	 * to restore correct number of queues
+	 */
+	int orig_num_active_queues;
 
 #define IAVF_MAX_FDIR_FILTERS 128	/* max allowed Flow Director filters */
 	u16 fdir_active_fltr;
@@ -393,16 +406,62 @@
 extern char iavf_driver_name[];
 extern struct workqueue_struct *iavf_wq;
 
+static inline const char *iavf_state_str(enum iavf_state_t state)
+{
+	switch (state) {
+	case __IAVF_STARTUP:
+		return "__IAVF_STARTUP";
+	case __IAVF_REMOVE:
+		return "__IAVF_REMOVE";
+	case __IAVF_INIT_VERSION_CHECK:
+		return "__IAVF_INIT_VERSION_CHECK";
+	case __IAVF_INIT_GET_RESOURCES:
+		return "__IAVF_INIT_GET_RESOURCES";
+	case __IAVF_INIT_SW:
+		return "__IAVF_INIT_SW";
+	case __IAVF_INIT_FAILED:
+		return "__IAVF_INIT_FAILED";
+	case __IAVF_RESETTING:
+		return "__IAVF_RESETTING";
+	case __IAVF_COMM_FAILED:
+		return "__IAVF_COMM_FAILED";
+	case __IAVF_DOWN:
+		return "__IAVF_DOWN";
+	case __IAVF_DOWN_PENDING:
+		return "__IAVF_DOWN_PENDING";
+	case __IAVF_TESTING:
+		return "__IAVF_TESTING";
+	case __IAVF_RUNNING:
+		return "__IAVF_RUNNING";
+	default:
+		return "__IAVF_UNKNOWN_STATE";
+	}
+}
+
+static inline void iavf_change_state(struct iavf_adapter *adapter,
+				     enum iavf_state_t state)
+{
+	if (adapter->state != state) {
+		adapter->last_state = adapter->state;
+		adapter->state = state;
+	}
+	dev_dbg(&adapter->pdev->dev,
+		"state transition from:%s to:%s\n",
+		iavf_state_str(adapter->last_state),
+		iavf_state_str(adapter->state));
+}
+
 int iavf_up(struct iavf_adapter *adapter);
 void iavf_down(struct iavf_adapter *adapter);
 int iavf_process_config(struct iavf_adapter *adapter);
 void iavf_schedule_reset(struct iavf_adapter *adapter);
+void iavf_schedule_request_stats(struct iavf_adapter *adapter);
 void iavf_reset(struct iavf_adapter *adapter);
 void iavf_set_ethtool_ops(struct net_device *netdev);
 void iavf_update_stats(struct iavf_adapter *adapter);
 void iavf_reset_interrupt_capability(struct iavf_adapter *adapter);
 int iavf_init_interrupt_scheme(struct iavf_adapter *adapter);
-void iavf_irq_enable_queues(struct iavf_adapter *adapter, u32 mask);
+void iavf_irq_enable_queues(struct iavf_adapter *adapter);
 void iavf_free_all_tx_resources(struct iavf_adapter *adapter);
 void iavf_free_all_rx_resources(struct iavf_adapter *adapter);
 
@@ -454,4 +513,5 @@
 void iavf_del_adv_rss_cfg(struct iavf_adapter *adapter);
 struct iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
 					const u8 *macaddr);
+int iavf_lock_timeout(struct mutex *lock, unsigned int msecs);
 #endif /* _IAVF_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_adminq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_adminq.c
@@ -324,6 +324,7 @@
 static enum iavf_status iavf_init_asq(struct iavf_hw *hw)
 {
 	enum iavf_status ret_code = 0;
+	int i;
 
 	if (hw->aq.asq.count > 0) {
 		/* queue already initialized */
@@ -354,12 +355,17 @@
 	/* initialize base registers */
 	ret_code = iavf_config_asq_regs(hw);
 	if (ret_code)
-		goto init_adminq_free_rings;
+		goto init_free_asq_bufs;
 
 	/* success! */
 	hw->aq.asq.count = hw->aq.num_asq_entries;
 	goto init_adminq_exit;
 
+init_free_asq_bufs:
+	for (i = 0; i < hw->aq.num_asq_entries; i++)
+		iavf_free_dma_mem(hw, &hw->aq.asq.r.asq_bi[i]);
+	iavf_free_virt_mem(hw, &hw->aq.asq.dma_head);
+
 init_adminq_free_rings:
 	iavf_free_adminq_asq(hw);
 
@@ -383,6 +389,7 @@
 static enum iavf_status iavf_init_arq(struct iavf_hw *hw)
 {
 	enum iavf_status ret_code = 0;
+	int i;
 
 	if (hw->aq.arq.count > 0) {
 		/* queue already initialized */
@@ -413,12 +420,16 @@
 	/* initialize base registers */
 	ret_code = iavf_config_arq_regs(hw);
 	if (ret_code)
-		goto init_adminq_free_rings;
+		goto init_free_arq_bufs;
 
 	/* success! */
 	hw->aq.arq.count = hw->aq.num_arq_entries;
 	goto init_adminq_exit;
 
+init_free_arq_bufs:
+	for (i = 0; i < hw->aq.num_arq_entries; i++)
+		iavf_free_dma_mem(hw, &hw->aq.arq.r.arq_bi[i]);
+	iavf_free_virt_mem(hw, &hw->aq.arq.dma_head);
 init_adminq_free_rings:
 	iavf_free_adminq_arq(hw);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_common.c
@@ -661,7 +661,7 @@
 	/* Non Tunneled IPv6 */
 	IAVF_PTT(88, IP, IPV6, FRG, NONE, NONE, NOF, NONE, PAY3),
 	IAVF_PTT(89, IP, IPV6, NOF, NONE, NONE, NOF, NONE, PAY3),
-	IAVF_PTT(90, IP, IPV6, NOF, NONE, NONE, NOF, UDP,  PAY3),
+	IAVF_PTT(90, IP, IPV6, NOF, NONE, NONE, NOF, UDP,  PAY4),
 	IAVF_PTT_UNUSED_ENTRY(91),
 	IAVF_PTT(92, IP, IPV6, NOF, NONE, NONE, NOF, TCP,  PAY4),
 	IAVF_PTT(93, IP, IPV6, NOF, NONE, NONE, NOF, SCTP, PAY4),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_ethtool.c
@@ -354,6 +354,9 @@
 	struct iavf_adapter *adapter = netdev_priv(netdev);
 	unsigned int i;
 
+	/* Explicitly request stats refresh */
+	iavf_schedule_request_stats(adapter);
+
 	iavf_add_ethtool_stats(&data, adapter, iavf_gstrings_stats);
 
 	rcu_read_lock();
@@ -612,23 +615,44 @@
 	if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending))
 		return -EINVAL;
 
-	new_tx_count = clamp_t(u32, ring->tx_pending,
-			       IAVF_MIN_TXD,
-			       IAVF_MAX_TXD);
-	new_tx_count = ALIGN(new_tx_count, IAVF_REQ_DESCRIPTOR_MULTIPLE);
-
-	new_rx_count = clamp_t(u32, ring->rx_pending,
-			       IAVF_MIN_RXD,
-			       IAVF_MAX_RXD);
-	new_rx_count = ALIGN(new_rx_count, IAVF_REQ_DESCRIPTOR_MULTIPLE);
+	if (ring->tx_pending > IAVF_MAX_TXD ||
+	    ring->tx_pending < IAVF_MIN_TXD ||
+	    ring->rx_pending > IAVF_MAX_RXD ||
+	    ring->rx_pending < IAVF_MIN_RXD) {
+		netdev_err(netdev, "Descriptors requested (Tx: %d / Rx: %d) out of range [%d-%d] (increment %d)\n",
+			   ring->tx_pending, ring->rx_pending, IAVF_MIN_TXD,
+			   IAVF_MAX_RXD, IAVF_REQ_DESCRIPTOR_MULTIPLE);
+		return -EINVAL;
+	}
+
+	new_tx_count = ALIGN(ring->tx_pending, IAVF_REQ_DESCRIPTOR_MULTIPLE);
+	if (new_tx_count != ring->tx_pending)
+		netdev_info(netdev, "Requested Tx descriptor count rounded up to %d\n",
+			    new_tx_count);
+
+	new_rx_count = ALIGN(ring->rx_pending, IAVF_REQ_DESCRIPTOR_MULTIPLE);
+	if (new_rx_count != ring->rx_pending)
+		netdev_info(netdev, "Requested Rx descriptor count rounded up to %d\n",
+			    new_rx_count);
 
 	/* if nothing to do return success */
 	if ((new_tx_count == adapter->tx_desc_count) &&
-	    (new_rx_count == adapter->rx_desc_count))
+	    (new_rx_count == adapter->rx_desc_count)) {
+		netdev_dbg(netdev, "Nothing to change, descriptor count is same as requested\n");
 		return 0;
+	}
 
-	adapter->tx_desc_count = new_tx_count;
-	adapter->rx_desc_count = new_rx_count;
+	if (new_tx_count != adapter->tx_desc_count) {
+		netdev_dbg(netdev, "Changing Tx descriptor count from %d to %d\n",
+			   adapter->tx_desc_count, new_tx_count);
+		adapter->tx_desc_count = new_tx_count;
+	}
+
+	if (new_rx_count != adapter->rx_desc_count) {
+		netdev_dbg(netdev, "Changing Rx descriptor count from %d to %d\n",
+			   adapter->rx_desc_count, new_rx_count);
+		adapter->rx_desc_count = new_rx_count;
+	}
 
 	if (netif_running(netdev)) {
 		adapter->flags |= IAVF_FLAG_RESET_NEEDED;
@@ -723,12 +747,31 @@
  *
  * Change the ITR settings for a specific queue.
  **/
-static void iavf_set_itr_per_queue(struct iavf_adapter *adapter,
-				   struct ethtool_coalesce *ec, int queue)
+static int iavf_set_itr_per_queue(struct iavf_adapter *adapter,
+				  struct ethtool_coalesce *ec, int queue)
 {
 	struct iavf_ring *rx_ring = &adapter->rx_rings[queue];
 	struct iavf_ring *tx_ring = &adapter->tx_rings[queue];
 	struct iavf_q_vector *q_vector;
+	u16 itr_setting;
+
+	itr_setting = rx_ring->itr_setting & ~IAVF_ITR_DYNAMIC;
+
+	if (ec->rx_coalesce_usecs != itr_setting &&
+	    ec->use_adaptive_rx_coalesce) {
+		netif_info(adapter, drv, adapter->netdev,
+			   "Rx interrupt throttling cannot be changed if adaptive-rx is enabled\n");
+		return -EINVAL;
+	}
+
+	itr_setting = tx_ring->itr_setting & ~IAVF_ITR_DYNAMIC;
+
+	if (ec->tx_coalesce_usecs != itr_setting &&
+	    ec->use_adaptive_tx_coalesce) {
+		netif_info(adapter, drv, adapter->netdev,
+			   "Tx interrupt throttling cannot be changed if adaptive-tx is enabled\n");
+		return -EINVAL;
+	}
 
 	rx_ring->itr_setting = ITR_REG_ALIGN(ec->rx_coalesce_usecs);
 	tx_ring->itr_setting = ITR_REG_ALIGN(ec->tx_coalesce_usecs);
@@ -751,6 +794,7 @@
 	 * the Tx and Rx ITR values based on the values we have entered
 	 * into the q_vector, no need to write the values now.
 	 */
+	return 0;
 }
 
 /**
@@ -792,9 +836,11 @@
 	 */
 	if (queue < 0) {
 		for (i = 0; i < adapter->num_active_queues; i++)
-			iavf_set_itr_per_queue(adapter, ec, i);
+			if (iavf_set_itr_per_queue(adapter, ec, i))
+				return -EINVAL;
 	} else if (queue < adapter->num_active_queues) {
-		iavf_set_itr_per_queue(adapter, ec, queue);
+		if (iavf_set_itr_per_queue(adapter, ec, queue))
+			return -EINVAL;
 	} else {
 		netif_info(adapter, drv, netdev, "Invalid queue value, queue range is 0 - %d\n",
 			   adapter->num_active_queues - 1);
@@ -1229,6 +1275,7 @@
 		fltr->ip_mask.src_port = fsp->m_u.tcp_ip4_spec.psrc;
 		fltr->ip_mask.dst_port = fsp->m_u.tcp_ip4_spec.pdst;
 		fltr->ip_mask.tos = fsp->m_u.tcp_ip4_spec.tos;
+		fltr->ip_ver = 4;
 		break;
 	case AH_V4_FLOW:
 	case ESP_V4_FLOW:
@@ -1240,6 +1287,7 @@
 		fltr->ip_mask.v4_addrs.dst_ip = fsp->m_u.ah_ip4_spec.ip4dst;
 		fltr->ip_mask.spi = fsp->m_u.ah_ip4_spec.spi;
 		fltr->ip_mask.tos = fsp->m_u.ah_ip4_spec.tos;
+		fltr->ip_ver = 4;
 		break;
 	case IPV4_USER_FLOW:
 		fltr->ip_data.v4_addrs.src_ip = fsp->h_u.usr_ip4_spec.ip4src;
@@ -1252,6 +1300,7 @@
 		fltr->ip_mask.l4_header = fsp->m_u.usr_ip4_spec.l4_4_bytes;
 		fltr->ip_mask.tos = fsp->m_u.usr_ip4_spec.tos;
 		fltr->ip_mask.proto = fsp->m_u.usr_ip4_spec.proto;
+		fltr->ip_ver = 4;
 		break;
 	case TCP_V6_FLOW:
 	case UDP_V6_FLOW:
@@ -1270,6 +1319,7 @@
 		fltr->ip_mask.src_port = fsp->m_u.tcp_ip6_spec.psrc;
 		fltr->ip_mask.dst_port = fsp->m_u.tcp_ip6_spec.pdst;
 		fltr->ip_mask.tclass = fsp->m_u.tcp_ip6_spec.tclass;
+		fltr->ip_ver = 6;
 		break;
 	case AH_V6_FLOW:
 	case ESP_V6_FLOW:
@@ -1285,6 +1335,7 @@
 		       sizeof(struct in6_addr));
 		fltr->ip_mask.spi = fsp->m_u.ah_ip6_spec.spi;
 		fltr->ip_mask.tclass = fsp->m_u.ah_ip6_spec.tclass;
+		fltr->ip_ver = 6;
 		break;
 	case IPV6_USER_FLOW:
 		memcpy(&fltr->ip_data.v6_addrs.src_ip, fsp->h_u.usr_ip6_spec.ip6src,
@@ -1301,6 +1352,7 @@
 		fltr->ip_mask.l4_header = fsp->m_u.usr_ip6_spec.l4_4_bytes;
 		fltr->ip_mask.tclass = fsp->m_u.usr_ip6_spec.tclass;
 		fltr->ip_mask.proto = fsp->m_u.usr_ip6_spec.l4_proto;
+		fltr->ip_ver = 6;
 		break;
 	case ETHER_FLOW:
 		fltr->eth_data.etype = fsp->h_u.ether_spec.h_proto;
@@ -1311,6 +1363,10 @@
 		return -EINVAL;
 	}
 
+	err = iavf_validate_fdir_fltr_masks(adapter, fltr);
+	if (err)
+		return err;
+
 	if (iavf_fdir_is_dup_fltr(adapter, fltr))
 		return -EEXIST;
 
@@ -1341,14 +1397,15 @@
 	if (fsp->flow_type & FLOW_MAC_EXT)
 		return -EINVAL;
 
+	spin_lock_bh(&adapter->fdir_fltr_lock);
 	if (adapter->fdir_active_fltr >= IAVF_MAX_FDIR_FILTERS) {
+		spin_unlock_bh(&adapter->fdir_fltr_lock);
 		dev_err(&adapter->pdev->dev,
 			"Unable to add Flow Director filter because VF reached the limit of max allowed filters (%u)\n",
 			IAVF_MAX_FDIR_FILTERS);
 		return -ENOSPC;
 	}
 
-	spin_lock_bh(&adapter->fdir_fltr_lock);
 	if (iavf_find_fdir_fltr_by_loc(adapter, fsp->location)) {
 		dev_err(&adapter->pdev->dev, "Failed to add Flow Director filter, it already exists\n");
 		spin_unlock_bh(&adapter->fdir_fltr_lock);
@@ -1721,7 +1778,9 @@
 	case ETHTOOL_GRXCLSRLCNT:
 		if (!FDIR_FLTR_SUPPORT(adapter))
 			break;
+		spin_lock_bh(&adapter->fdir_fltr_lock);
 		cmd->rule_cnt = adapter->fdir_active_fltr;
+		spin_unlock_bh(&adapter->fdir_fltr_lock);
 		cmd->data = IAVF_MAX_FDIR_FILTERS;
 		ret = 0;
 		break;
@@ -1776,6 +1835,7 @@
 {
 	struct iavf_adapter *adapter = netdev_priv(netdev);
 	u32 num_req = ch->combined_count;
+	int i;
 
 	if ((adapter->vf_res->vf_cap_flags & VIRTCHNL_VF_OFFLOAD_ADQ) &&
 	    adapter->num_tc) {
@@ -1786,7 +1846,7 @@
 	/* All of these should have already been checked by ethtool before this
 	 * even gets to us, but just to be sure.
 	 */
-	if (num_req > adapter->vsi_res->num_queue_pairs)
+	if (num_req == 0 || num_req > adapter->vsi_res->num_queue_pairs)
 		return -EINVAL;
 
 	if (num_req == adapter->num_active_queues)
@@ -1798,6 +1858,20 @@
 	adapter->num_req_queues = num_req;
 	adapter->flags |= IAVF_FLAG_REINIT_ITR_NEEDED;
 	iavf_schedule_reset(adapter);
+
+	/* wait for the reset is done */
+	for (i = 0; i < IAVF_RESET_WAIT_COMPLETE_COUNT; i++) {
+		msleep(IAVF_RESET_WAIT_MS);
+		if (adapter->flags & IAVF_FLAG_RESET_PENDING)
+			continue;
+		break;
+	}
+	if (i == IAVF_RESET_WAIT_COMPLETE_COUNT) {
+		adapter->flags &= ~IAVF_FLAG_REINIT_ITR_NEEDED;
+		adapter->num_req_queues = 0;
+		return -EOPNOTSUPP;
+	}
+
 	return 0;
 }
 
@@ -1844,14 +1918,13 @@
 
 	if (hfunc)
 		*hfunc = ETH_RSS_HASH_TOP;
-	if (!indir)
-		return 0;
-
-	memcpy(key, adapter->rss_key, adapter->rss_key_size);
+	if (key)
+		memcpy(key, adapter->rss_key, adapter->rss_key_size);
 
-	/* Each 32 bits pointed by 'indir' is stored with a lut entry */
-	for (i = 0; i < adapter->rss_lut_size; i++)
-		indir[i] = (u32)adapter->rss_lut[i];
+	if (indir)
+		/* Each 32 bits pointed by 'indir' is stored with a lut entry */
+		for (i = 0; i < adapter->rss_lut_size; i++)
+			indir[i] = (u32)adapter->rss_lut[i];
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_fdir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_fdir.c
@@ -18,6 +18,79 @@
 	}
 };
 
+static const struct in6_addr ipv6_addr_zero_mask = {
+	.in6_u = {
+		.u6_addr8 = {
+			0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+		}
+	}
+};
+
+/**
+ * iavf_validate_fdir_fltr_masks - validate Flow Director filter fields masks
+ * @adapter: pointer to the VF adapter structure
+ * @fltr: Flow Director filter data structure
+ *
+ * Returns 0 if all masks of packet fields are either full or empty. Returns
+ * error on at least one partial mask.
+ */
+int iavf_validate_fdir_fltr_masks(struct iavf_adapter *adapter,
+				  struct iavf_fdir_fltr *fltr)
+{
+	if (fltr->eth_mask.etype && fltr->eth_mask.etype != htons(U16_MAX))
+		goto partial_mask;
+
+	if (fltr->ip_ver == 4) {
+		if (fltr->ip_mask.v4_addrs.src_ip &&
+		    fltr->ip_mask.v4_addrs.src_ip != htonl(U32_MAX))
+			goto partial_mask;
+
+		if (fltr->ip_mask.v4_addrs.dst_ip &&
+		    fltr->ip_mask.v4_addrs.dst_ip != htonl(U32_MAX))
+			goto partial_mask;
+
+		if (fltr->ip_mask.tos && fltr->ip_mask.tos != U8_MAX)
+			goto partial_mask;
+	} else if (fltr->ip_ver == 6) {
+		if (memcmp(&fltr->ip_mask.v6_addrs.src_ip, &ipv6_addr_zero_mask,
+			   sizeof(struct in6_addr)) &&
+		    memcmp(&fltr->ip_mask.v6_addrs.src_ip, &ipv6_addr_full_mask,
+			   sizeof(struct in6_addr)))
+			goto partial_mask;
+
+		if (memcmp(&fltr->ip_mask.v6_addrs.dst_ip, &ipv6_addr_zero_mask,
+			   sizeof(struct in6_addr)) &&
+		    memcmp(&fltr->ip_mask.v6_addrs.dst_ip, &ipv6_addr_full_mask,
+			   sizeof(struct in6_addr)))
+			goto partial_mask;
+
+		if (fltr->ip_mask.tclass && fltr->ip_mask.tclass != U8_MAX)
+			goto partial_mask;
+	}
+
+	if (fltr->ip_mask.proto && fltr->ip_mask.proto != U8_MAX)
+		goto partial_mask;
+
+	if (fltr->ip_mask.src_port && fltr->ip_mask.src_port != htons(U16_MAX))
+		goto partial_mask;
+
+	if (fltr->ip_mask.dst_port && fltr->ip_mask.dst_port != htons(U16_MAX))
+		goto partial_mask;
+
+	if (fltr->ip_mask.spi && fltr->ip_mask.spi != htonl(U32_MAX))
+		goto partial_mask;
+
+	if (fltr->ip_mask.l4_header &&
+	    fltr->ip_mask.l4_header != htonl(U32_MAX))
+		goto partial_mask;
+
+	return 0;
+
+partial_mask:
+	dev_err(&adapter->pdev->dev, "Failed to add Flow Director filter, partial masks are not supported\n");
+	return -EOPNOTSUPP;
+}
+
 /**
  * iavf_pkt_udp_no_pay_len - the length of UDP packet without payload
  * @fltr: Flow Director filter data structure
@@ -263,8 +336,6 @@
 		VIRTCHNL_ADD_PROTO_HDR_FIELD_BIT(hdr, IPV4, DST);
 	}
 
-	fltr->ip_ver = 4;
-
 	return 0;
 }
 
@@ -309,8 +380,6 @@
 		VIRTCHNL_ADD_PROTO_HDR_FIELD_BIT(hdr, IPV6, DST);
 	}
 
-	fltr->ip_ver = 6;
-
 	return 0;
 }
 
@@ -722,7 +791,9 @@
 bool iavf_fdir_is_dup_fltr(struct iavf_adapter *adapter, struct iavf_fdir_fltr *fltr)
 {
 	struct iavf_fdir_fltr *tmp;
+	bool ret = false;
 
+	spin_lock_bh(&adapter->fdir_fltr_lock);
 	list_for_each_entry(tmp, &adapter->fdir_list_head, list) {
 		if (tmp->flow_type != fltr->flow_type)
 			continue;
@@ -732,11 +803,14 @@
 		    !memcmp(&tmp->ip_data, &fltr->ip_data,
 			    sizeof(fltr->ip_data)) &&
 		    !memcmp(&tmp->ext_data, &fltr->ext_data,
-			    sizeof(fltr->ext_data)))
-			return true;
+			    sizeof(fltr->ext_data))) {
+			ret = true;
+			break;
+		}
 	}
+	spin_unlock_bh(&adapter->fdir_fltr_lock);
 
-	return false;
+	return ret;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_fdir.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_fdir.h
@@ -110,6 +110,8 @@
 	struct virtchnl_fdir_add vc_add_msg;
 };
 
+int iavf_validate_fdir_fltr_masks(struct iavf_adapter *adapter,
+				  struct iavf_fdir_fltr *fltr);
 int iavf_fill_fdir_add_msg(struct iavf_adapter *adapter, struct iavf_fdir_fltr *fltr);
 void iavf_print_fdir_fltr(struct iavf_adapter *adapter, struct iavf_fdir_fltr *fltr);
 bool iavf_fdir_is_dup_fltr(struct iavf_adapter *adapter, struct iavf_fdir_fltr *fltr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_main.c
@@ -14,7 +14,7 @@
 static int iavf_setup_all_tx_resources(struct iavf_adapter *adapter);
 static int iavf_setup_all_rx_resources(struct iavf_adapter *adapter);
 static int iavf_close(struct net_device *netdev);
-static int iavf_init_get_resources(struct iavf_adapter *adapter);
+static void iavf_init_get_resources(struct iavf_adapter *adapter);
 static int iavf_check_reset_complete(struct iavf_hw *hw);
 
 char iavf_driver_name[] = "iavf";
@@ -52,6 +52,15 @@
 struct workqueue_struct *iavf_wq;
 
 /**
+ * iavf_pdev_to_adapter - go from pci_dev to adapter
+ * @pdev: pci_dev pointer
+ */
+static struct iavf_adapter *iavf_pdev_to_adapter(struct pci_dev *pdev)
+{
+	return netdev_priv(pci_get_drvdata(pdev));
+}
+
+/**
  * iavf_allocate_dma_mem_d - OS specific memory alloc for shared code
  * @hw:   pointer to the HW structure
  * @mem:  ptr to mem struct to fill out
@@ -138,7 +147,7 @@
  *
  * Returns 0 on success, negative on failure
  **/
-static int iavf_lock_timeout(struct mutex *lock, unsigned int msecs)
+int iavf_lock_timeout(struct mutex *lock, unsigned int msecs)
 {
 	unsigned int wait, delay = 10;
 
@@ -166,6 +175,19 @@
 }
 
 /**
+ * iavf_schedule_request_stats - Set the flags and schedule statistics request
+ * @adapter: board private structure
+ *
+ * Sets IAVF_FLAG_AQ_REQUEST_STATS flag so iavf_watchdog_task() will explicitly
+ * request and refresh ethtool stats
+ **/
+void iavf_schedule_request_stats(struct iavf_adapter *adapter)
+{
+	adapter->aq_required |= IAVF_FLAG_AQ_REQUEST_STATS;
+	mod_delayed_work(iavf_wq, &adapter->watchdog_task, 0);
+}
+
+/**
  * iavf_tx_timeout - Respond to a Tx Hang
  * @netdev: network interface device structure
  * @txqueue: queue number that is timing out
@@ -231,21 +253,18 @@
 }
 
 /**
- * iavf_irq_enable_queues - Enable interrupt for specified queues
+ * iavf_irq_enable_queues - Enable interrupt for all queues
  * @adapter: board private structure
- * @mask: bitmap of queues to enable
  **/
-void iavf_irq_enable_queues(struct iavf_adapter *adapter, u32 mask)
+void iavf_irq_enable_queues(struct iavf_adapter *adapter)
 {
 	struct iavf_hw *hw = &adapter->hw;
 	int i;
 
 	for (i = 1; i < adapter->num_msix_vectors; i++) {
-		if (mask & BIT(i - 1)) {
-			wr32(hw, IAVF_VFINT_DYN_CTLN1(i - 1),
-			     IAVF_VFINT_DYN_CTLN1_INTENA_MASK |
-			     IAVF_VFINT_DYN_CTLN1_ITR_INDX_MASK);
-		}
+		wr32(hw, IAVF_VFINT_DYN_CTLN1(i - 1),
+		     IAVF_VFINT_DYN_CTLN1_INTENA_MASK |
+		     IAVF_VFINT_DYN_CTLN1_ITR_INDX_MASK);
 	}
 }
 
@@ -259,7 +278,7 @@
 	struct iavf_hw *hw = &adapter->hw;
 
 	iavf_misc_irq_enable(adapter);
-	iavf_irq_enable_queues(adapter, ~0);
+	iavf_irq_enable_queues(adapter);
 
 	if (flush)
 		iavf_flush(hw);
@@ -280,8 +299,9 @@
 	rd32(hw, IAVF_VFINT_ICR01);
 	rd32(hw, IAVF_VFINT_ICR0_ENA1);
 
-	/* schedule work on the private workqueue */
-	queue_work(iavf_wq, &adapter->adminq_task);
+	if (adapter->state != __IAVF_REMOVE)
+		/* schedule work on the private workqueue */
+		queue_work(iavf_wq, &adapter->adminq_task);
 
 	return IRQ_HANDLED;
 }
@@ -688,6 +708,21 @@
 }
 
 /**
+ * iavf_restore_filters
+ * @adapter: board private structure
+ *
+ * Restore existing non MAC filters when VF netdev comes back up
+ **/
+static void iavf_restore_filters(struct iavf_adapter *adapter)
+{
+	u16 vid;
+
+	/* re-add all VLAN filters */
+	for_each_set_bit(vid, adapter->vsi.active_vlans, VLAN_N_VID)
+		iavf_add_vlan(adapter, vid);
+}
+
+/**
  * iavf_vlan_rx_add_vid - Add a VLAN filter to a device
  * @netdev: network device struct
  * @proto: unused protocol data
@@ -700,8 +735,11 @@
 
 	if (!VLAN_ALLOWED(adapter))
 		return -EIO;
+
 	if (iavf_add_vlan(adapter, vid) == NULL)
 		return -ENOMEM;
+
+	set_bit(vid, adapter->vsi.active_vlans);
 	return 0;
 }
 
@@ -716,11 +754,10 @@
 {
 	struct iavf_adapter *adapter = netdev_priv(netdev);
 
-	if (VLAN_ALLOWED(adapter)) {
-		iavf_del_vlan(adapter, vid);
-		return 0;
-	}
-	return -EIO;
+	iavf_del_vlan(adapter, vid);
+	clear_bit(vid, adapter->vsi.active_vlans);
+
+	return 0;
 }
 
 /**
@@ -960,7 +997,7 @@
  **/
 static void iavf_up_complete(struct iavf_adapter *adapter)
 {
-	adapter->state = __IAVF_RUNNING;
+	iavf_change_state(adapter, __IAVF_RUNNING);
 	clear_bit(__IAVF_VSI_DOWN, adapter->vsi.state);
 
 	iavf_napi_enable_all(adapter);
@@ -972,80 +1009,157 @@
 }
 
 /**
- * iavf_down - Shutdown the connection processing
+ * iavf_clear_mac_vlan_filters - Remove mac and vlan filters not sent to PF
+ * yet and mark other to be removed.
  * @adapter: board private structure
- *
- * Expects to be called while holding the __IAVF_IN_CRITICAL_TASK bit lock.
  **/
-void iavf_down(struct iavf_adapter *adapter)
+static void iavf_clear_mac_vlan_filters(struct iavf_adapter *adapter)
 {
-	struct net_device *netdev = adapter->netdev;
-	struct iavf_vlan_filter *vlf;
-	struct iavf_cloud_filter *cf;
-	struct iavf_fdir_fltr *fdir;
-	struct iavf_mac_filter *f;
-	struct iavf_adv_rss *rss;
-
-	if (adapter->state <= __IAVF_DOWN_PENDING)
-		return;
-
-	netif_carrier_off(netdev);
-	netif_tx_disable(netdev);
-	adapter->link_up = false;
-	iavf_napi_disable_all(adapter);
-	iavf_irq_disable(adapter);
+	struct iavf_vlan_filter *vlf, *vlftmp;
+	struct iavf_mac_filter *f, *ftmp;
 
 	spin_lock_bh(&adapter->mac_vlan_list_lock);
-
 	/* clear the sync flag on all filters */
 	__dev_uc_unsync(adapter->netdev, NULL);
 	__dev_mc_unsync(adapter->netdev, NULL);
 
 	/* remove all MAC filters */
-	list_for_each_entry(f, &adapter->mac_filter_list, list) {
-		f->remove = true;
+	list_for_each_entry_safe(f, ftmp, &adapter->mac_filter_list,
+				 list) {
+		if (f->add) {
+			list_del(&f->list);
+			kfree(f);
+		} else {
+			f->remove = true;
+		}
 	}
 
 	/* remove all VLAN filters */
-	list_for_each_entry(vlf, &adapter->vlan_filter_list, list) {
-		vlf->remove = true;
+	list_for_each_entry_safe(vlf, vlftmp, &adapter->vlan_filter_list,
+				 list) {
+		if (vlf->add) {
+			list_del(&vlf->list);
+			kfree(vlf);
+		} else {
+			vlf->remove = true;
+		}
 	}
-
 	spin_unlock_bh(&adapter->mac_vlan_list_lock);
+}
+
+/**
+ * iavf_clear_cloud_filters - Remove cloud filters not sent to PF yet and
+ * mark other to be removed.
+ * @adapter: board private structure
+ **/
+static void iavf_clear_cloud_filters(struct iavf_adapter *adapter)
+{
+	struct iavf_cloud_filter *cf, *cftmp;
 
 	/* remove all cloud filters */
 	spin_lock_bh(&adapter->cloud_filter_list_lock);
-	list_for_each_entry(cf, &adapter->cloud_filter_list, list) {
-		cf->del = true;
+	list_for_each_entry_safe(cf, cftmp, &adapter->cloud_filter_list,
+				 list) {
+		if (cf->add) {
+			list_del(&cf->list);
+			kfree(cf);
+			adapter->num_cloud_filters--;
+		} else {
+			cf->del = true;
+		}
 	}
 	spin_unlock_bh(&adapter->cloud_filter_list_lock);
+}
+
+/**
+ * iavf_clear_fdir_filters - Remove fdir filters not sent to PF yet and mark
+ * other to be removed.
+ * @adapter: board private structure
+ **/
+static void iavf_clear_fdir_filters(struct iavf_adapter *adapter)
+{
+	struct iavf_fdir_fltr *fdir, *fdirtmp;
 
 	/* remove all Flow Director filters */
 	spin_lock_bh(&adapter->fdir_fltr_lock);
-	list_for_each_entry(fdir, &adapter->fdir_list_head, list) {
-		fdir->state = IAVF_FDIR_FLTR_DEL_REQUEST;
+	list_for_each_entry_safe(fdir, fdirtmp, &adapter->fdir_list_head,
+				 list) {
+		if (fdir->state == IAVF_FDIR_FLTR_ADD_REQUEST) {
+			list_del(&fdir->list);
+			kfree(fdir);
+			adapter->fdir_active_fltr--;
+		} else {
+			fdir->state = IAVF_FDIR_FLTR_DEL_REQUEST;
+		}
 	}
 	spin_unlock_bh(&adapter->fdir_fltr_lock);
+}
+
+/**
+ * iavf_clear_adv_rss_conf - Remove adv rss conf not sent to PF yet and mark
+ * other to be removed.
+ * @adapter: board private structure
+ **/
+static void iavf_clear_adv_rss_conf(struct iavf_adapter *adapter)
+{
+	struct iavf_adv_rss *rss, *rsstmp;
 
 	/* remove all advance RSS configuration */
 	spin_lock_bh(&adapter->adv_rss_lock);
-	list_for_each_entry(rss, &adapter->adv_rss_list_head, list)
-		rss->state = IAVF_ADV_RSS_DEL_REQUEST;
+	list_for_each_entry_safe(rss, rsstmp, &adapter->adv_rss_list_head,
+				 list) {
+		if (rss->state == IAVF_ADV_RSS_ADD_REQUEST) {
+			list_del(&rss->list);
+			kfree(rss);
+		} else {
+			rss->state = IAVF_ADV_RSS_DEL_REQUEST;
+		}
+	}
 	spin_unlock_bh(&adapter->adv_rss_lock);
+}
+
+/**
+ * iavf_down - Shutdown the connection processing
+ * @adapter: board private structure
+ *
+ * Expects to be called while holding the __IAVF_IN_CRITICAL_TASK bit lock.
+ **/
+void iavf_down(struct iavf_adapter *adapter)
+{
+	struct net_device *netdev = adapter->netdev;
+
+	if (adapter->state <= __IAVF_DOWN_PENDING)
+		return;
+
+	netif_carrier_off(netdev);
+	netif_tx_disable(netdev);
+	adapter->link_up = false;
+	iavf_napi_disable_all(adapter);
+	iavf_irq_disable(adapter);
+
+	iavf_clear_mac_vlan_filters(adapter);
+	iavf_clear_cloud_filters(adapter);
+	iavf_clear_fdir_filters(adapter);
+	iavf_clear_adv_rss_conf(adapter);
 
 	if (!(adapter->flags & IAVF_FLAG_PF_COMMS_FAILED) &&
-	    adapter->state != __IAVF_RESETTING) {
+	    !(test_bit(__IAVF_IN_REMOVE_TASK, &adapter->crit_section))) {
 		/* cancel any current operation */
 		adapter->current_op = VIRTCHNL_OP_UNKNOWN;
 		/* Schedule operations to close down the HW. Don't wait
 		 * here for this to complete. The watchdog is still running
 		 * and it will take care of this.
 		 */
-		adapter->aq_required = IAVF_FLAG_AQ_DEL_MAC_FILTER;
-		adapter->aq_required |= IAVF_FLAG_AQ_DEL_VLAN_FILTER;
-		adapter->aq_required |= IAVF_FLAG_AQ_DEL_CLOUD_FILTER;
-		adapter->aq_required |= IAVF_FLAG_AQ_DEL_FDIR_FILTER;
-		adapter->aq_required |= IAVF_FLAG_AQ_DEL_ADV_RSS_CFG;
+		if (!list_empty(&adapter->mac_filter_list))
+			adapter->aq_required |= IAVF_FLAG_AQ_DEL_MAC_FILTER;
+		if (!list_empty(&adapter->vlan_filter_list))
+			adapter->aq_required |= IAVF_FLAG_AQ_DEL_VLAN_FILTER;
+		if (!list_empty(&adapter->cloud_filter_list))
+			adapter->aq_required |= IAVF_FLAG_AQ_DEL_CLOUD_FILTER;
+		if (!list_empty(&adapter->fdir_list_head))
+			adapter->aq_required |= IAVF_FLAG_AQ_DEL_FDIR_FILTER;
+		if (!list_empty(&adapter->adv_rss_list_head))
+			adapter->aq_required |= IAVF_FLAG_AQ_DEL_ADV_RSS_CFG;
 		adapter->aq_required |= IAVF_FLAG_AQ_DISABLE_QUEUES;
 	}
 
@@ -1332,7 +1446,6 @@
 static int iavf_init_rss(struct iavf_adapter *adapter)
 {
 	struct iavf_hw *hw = &adapter->hw;
-	int ret;
 
 	if (!RSS_PF(adapter)) {
 		/* Enable PCTYPES for RSS, TCP/UDP with IPv4/IPv6 */
@@ -1348,9 +1461,8 @@
 
 	iavf_fill_rss_lut(adapter);
 	netdev_rss_key_fill((void *)adapter->rss_key, adapter->rss_key_size);
-	ret = iavf_config_rss(adapter);
 
-	return ret;
+	return iavf_config_rss(adapter);
 }
 
 /**
@@ -1396,19 +1508,16 @@
 static void iavf_free_q_vectors(struct iavf_adapter *adapter)
 {
 	int q_idx, num_q_vectors;
-	int napi_vectors;
 
 	if (!adapter->q_vectors)
 		return;
 
 	num_q_vectors = adapter->num_msix_vectors - NONQ_VECS;
-	napi_vectors = adapter->num_active_queues;
 
 	for (q_idx = 0; q_idx < num_q_vectors; q_idx++) {
 		struct iavf_q_vector *q_vector = &adapter->q_vectors[q_idx];
 
-		if (q_idx < napi_vectors)
-			netif_napi_del(&q_vector->napi);
+		netif_napi_del(&q_vector->napi);
 	}
 	kfree(adapter->q_vectors);
 	adapter->q_vectors = NULL;
@@ -1630,8 +1739,7 @@
 		iavf_set_promiscuous(adapter, FLAG_VF_MULTICAST_PROMISC);
 		return 0;
 	}
-
-	if ((adapter->aq_required & IAVF_FLAG_AQ_RELEASE_PROMISC) &&
+	if ((adapter->aq_required & IAVF_FLAG_AQ_RELEASE_PROMISC) ||
 	    (adapter->aq_required & IAVF_FLAG_AQ_RELEASE_ALLMULTI)) {
 		iavf_set_promiscuous(adapter, 0);
 		return 0;
@@ -1679,6 +1787,11 @@
 		iavf_del_adv_rss_cfg(adapter);
 		return 0;
 	}
+	if (adapter->aq_required & IAVF_FLAG_AQ_REQUEST_STATS) {
+		iavf_request_stats(adapter);
+		return 0;
+	}
+
 	return -EAGAIN;
 }
 
@@ -1688,9 +1801,9 @@
  *
  * Function process __IAVF_STARTUP driver state.
  * When success the state is changed to __IAVF_INIT_VERSION_CHECK
- * when fails it returns -EAGAIN
+ * when fails the state is changed to __IAVF_INIT_FAILED
  **/
-static int iavf_startup(struct iavf_adapter *adapter)
+static void iavf_startup(struct iavf_adapter *adapter)
 {
 	struct pci_dev *pdev = adapter->pdev;
 	struct iavf_hw *hw = &adapter->hw;
@@ -1729,9 +1842,10 @@
 		iavf_shutdown_adminq(hw);
 		goto err;
 	}
-	adapter->state = __IAVF_INIT_VERSION_CHECK;
+	iavf_change_state(adapter, __IAVF_INIT_VERSION_CHECK);
+	return;
 err:
-	return err;
+	iavf_change_state(adapter, __IAVF_INIT_FAILED);
 }
 
 /**
@@ -1740,9 +1854,9 @@
  *
  * Function process __IAVF_INIT_VERSION_CHECK driver state.
  * When success the state is changed to __IAVF_INIT_GET_RESOURCES
- * when fails it returns -EAGAIN
+ * when fails the state is changed to __IAVF_INIT_FAILED
  **/
-static int iavf_init_version_check(struct iavf_adapter *adapter)
+static void iavf_init_version_check(struct iavf_adapter *adapter)
 {
 	struct pci_dev *pdev = adapter->pdev;
 	struct iavf_hw *hw = &adapter->hw;
@@ -1753,7 +1867,7 @@
 	if (!iavf_asq_done(hw)) {
 		dev_err(&pdev->dev, "Admin queue command never completed\n");
 		iavf_shutdown_adminq(hw);
-		adapter->state = __IAVF_STARTUP;
+		iavf_change_state(adapter, __IAVF_STARTUP);
 		goto err;
 	}
 
@@ -1776,10 +1890,10 @@
 			err);
 		goto err;
 	}
-	adapter->state = __IAVF_INIT_GET_RESOURCES;
-
+	iavf_change_state(adapter, __IAVF_INIT_GET_RESOURCES);
+	return;
 err:
-	return err;
+	iavf_change_state(adapter, __IAVF_INIT_FAILED);
 }
 
 /**
@@ -1789,9 +1903,9 @@
  * Function process __IAVF_INIT_GET_RESOURCES driver state and
  * finishes driver initialization procedure.
  * When success the state is changed to __IAVF_DOWN
- * when fails it returns -EAGAIN
+ * when fails the state is changed to __IAVF_INIT_FAILED
  **/
-static int iavf_init_get_resources(struct iavf_adapter *adapter)
+static void iavf_init_get_resources(struct iavf_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
 	struct pci_dev *pdev = adapter->pdev;
@@ -1819,7 +1933,7 @@
 		 */
 		iavf_shutdown_adminq(hw);
 		dev_err(&pdev->dev, "Unable to get VF config due to PF error condition, not retrying\n");
-		return 0;
+		return;
 	}
 	if (err) {
 		dev_err(&pdev->dev, "Unable to get VF config (%d)\n", err);
@@ -1847,7 +1961,7 @@
 		eth_hw_addr_random(netdev);
 		ether_addr_copy(adapter->hw.mac.addr, netdev->dev_addr);
 	} else {
-		ether_addr_copy(netdev->dev_addr, adapter->hw.mac.addr);
+		eth_hw_addr_set(netdev, adapter->hw.mac.addr);
 		ether_addr_copy(netdev->perm_addr, adapter->hw.mac.addr);
 	}
 
@@ -1893,7 +2007,7 @@
 	if (netdev->features & NETIF_F_GRO)
 		dev_info(&pdev->dev, "GRO is enabled\n");
 
-	adapter->state = __IAVF_DOWN;
+	iavf_change_state(adapter, __IAVF_DOWN);
 	set_bit(__IAVF_VSI_DOWN, adapter->vsi.state);
 	rtnl_unlock();
 
@@ -1911,7 +2025,7 @@
 	else
 		iavf_init_rss(adapter);
 
-	return err;
+	return;
 err_mem:
 	iavf_free_rss(adapter);
 err_register:
@@ -1922,7 +2036,7 @@
 	kfree(adapter->vf_res);
 	adapter->vf_res = NULL;
 err:
-	return err;
+	iavf_change_state(adapter, __IAVF_INIT_FAILED);
 }
 
 /**
@@ -1937,14 +2051,80 @@
 	struct iavf_hw *hw = &adapter->hw;
 	u32 reg_val;
 
-	if (!mutex_trylock(&adapter->crit_lock))
+	if (!mutex_trylock(&adapter->crit_lock)) {
+		if (adapter->state == __IAVF_REMOVE)
+			return;
+
 		goto restart_watchdog;
+	}
 
 	if (adapter->flags & IAVF_FLAG_PF_COMMS_FAILED)
-		adapter->state = __IAVF_COMM_FAILED;
+		iavf_change_state(adapter, __IAVF_COMM_FAILED);
+
+	if (adapter->flags & IAVF_FLAG_RESET_NEEDED) {
+		adapter->aq_required = 0;
+		adapter->current_op = VIRTCHNL_OP_UNKNOWN;
+		mutex_unlock(&adapter->crit_lock);
+		queue_work(iavf_wq, &adapter->reset_task);
+		return;
+	}
 
 	switch (adapter->state) {
+	case __IAVF_STARTUP:
+		iavf_startup(adapter);
+		mutex_unlock(&adapter->crit_lock);
+		queue_delayed_work(iavf_wq, &adapter->watchdog_task,
+				   msecs_to_jiffies(30));
+		return;
+	case __IAVF_INIT_VERSION_CHECK:
+		iavf_init_version_check(adapter);
+		mutex_unlock(&adapter->crit_lock);
+		queue_delayed_work(iavf_wq, &adapter->watchdog_task,
+				   msecs_to_jiffies(30));
+		return;
+	case __IAVF_INIT_GET_RESOURCES:
+		iavf_init_get_resources(adapter);
+		mutex_unlock(&adapter->crit_lock);
+		queue_delayed_work(iavf_wq, &adapter->watchdog_task,
+				   msecs_to_jiffies(1));
+		return;
+	case __IAVF_INIT_FAILED:
+		if (test_bit(__IAVF_IN_REMOVE_TASK,
+			     &adapter->crit_section)) {
+			/* Do not update the state and do not reschedule
+			 * watchdog task, iavf_remove should handle this state
+			 * as it can loop forever
+			 */
+			mutex_unlock(&adapter->crit_lock);
+			return;
+		}
+		if (++adapter->aq_wait_count > IAVF_AQ_MAX_ERR) {
+			dev_err(&adapter->pdev->dev,
+				"Failed to communicate with PF; waiting before retry\n");
+			adapter->flags |= IAVF_FLAG_PF_COMMS_FAILED;
+			iavf_shutdown_adminq(hw);
+			mutex_unlock(&adapter->crit_lock);
+			queue_delayed_work(iavf_wq,
+					   &adapter->watchdog_task, (5 * HZ));
+			return;
+		}
+		/* Try again from failed step*/
+		iavf_change_state(adapter, adapter->last_state);
+		mutex_unlock(&adapter->crit_lock);
+		queue_delayed_work(iavf_wq, &adapter->watchdog_task, HZ);
+		return;
 	case __IAVF_COMM_FAILED:
+		if (test_bit(__IAVF_IN_REMOVE_TASK,
+			     &adapter->crit_section)) {
+			/* Set state to __IAVF_INIT_FAILED and perform remove
+			 * steps. Remove IAVF_FLAG_PF_COMMS_FAILED so the task
+			 * doesn't bring the state back to __IAVF_COMM_FAILED.
+			 */
+			iavf_change_state(adapter, __IAVF_INIT_FAILED);
+			adapter->flags &= ~IAVF_FLAG_PF_COMMS_FAILED;
+			mutex_unlock(&adapter->crit_lock);
+			return;
+		}
 		reg_val = rd32(hw, IAVF_VFGEN_RSTAT) &
 			  IAVF_VFGEN_RSTAT_VFR_STATE_MASK;
 		if (reg_val == VIRTCHNL_VFR_VFACTIVE ||
@@ -1952,23 +2132,20 @@
 			/* A chance for redemption! */
 			dev_err(&adapter->pdev->dev,
 				"Hardware came out of reset. Attempting reinit.\n");
-			adapter->state = __IAVF_STARTUP;
-			adapter->flags &= ~IAVF_FLAG_PF_COMMS_FAILED;
-			queue_delayed_work(iavf_wq, &adapter->init_task, 10);
-			mutex_unlock(&adapter->crit_lock);
-			/* Don't reschedule the watchdog, since we've restarted
-			 * the init task. When init_task contacts the PF and
+			/* When init task contacts the PF and
 			 * gets everything set up again, it'll restart the
 			 * watchdog for us. Down, boy. Sit. Stay. Woof.
 			 */
-			return;
+			iavf_change_state(adapter, __IAVF_STARTUP);
+			adapter->flags &= ~IAVF_FLAG_PF_COMMS_FAILED;
 		}
 		adapter->aq_required = 0;
 		adapter->current_op = VIRTCHNL_OP_UNKNOWN;
+		mutex_unlock(&adapter->crit_lock);
 		queue_delayed_work(iavf_wq,
 				   &adapter->watchdog_task,
 				   msecs_to_jiffies(10));
-		goto watchdog_done;
+		return;
 	case __IAVF_RESETTING:
 		mutex_unlock(&adapter->crit_lock);
 		queue_delayed_work(iavf_wq, &adapter->watchdog_task, HZ * 2);
@@ -1991,15 +2168,16 @@
 			    adapter->state == __IAVF_RUNNING)
 				iavf_request_stats(adapter);
 		}
+		if (adapter->state == __IAVF_RUNNING)
+			iavf_detect_recover_hung(&adapter->vsi);
 		break;
 	case __IAVF_REMOVE:
+	default:
 		mutex_unlock(&adapter->crit_lock);
 		return;
-	default:
-		goto restart_watchdog;
 	}
 
-		/* check for hw reset */
+	/* check for hw reset */
 	reg_val = rd32(hw, IAVF_VF_ARQLEN1) & IAVF_VF_ARQLEN1_ARQENABLE_MASK;
 	if (!reg_val) {
 		adapter->flags |= IAVF_FLAG_RESET_PENDING;
@@ -2007,24 +2185,31 @@
 		adapter->current_op = VIRTCHNL_OP_UNKNOWN;
 		dev_err(&adapter->pdev->dev, "Hardware reset detected\n");
 		queue_work(iavf_wq, &adapter->reset_task);
-		goto watchdog_done;
+		mutex_unlock(&adapter->crit_lock);
+		queue_delayed_work(iavf_wq,
+				   &adapter->watchdog_task, HZ * 2);
+		return;
 	}
 
 	schedule_delayed_work(&adapter->client_task, msecs_to_jiffies(5));
-watchdog_done:
-	if (adapter->state == __IAVF_RUNNING ||
-	    adapter->state == __IAVF_COMM_FAILED)
-		iavf_detect_recover_hung(&adapter->vsi);
 	mutex_unlock(&adapter->crit_lock);
 restart_watchdog:
+	if (adapter->state >= __IAVF_DOWN)
+		queue_work(iavf_wq, &adapter->adminq_task);
 	if (adapter->aq_required)
 		queue_delayed_work(iavf_wq, &adapter->watchdog_task,
 				   msecs_to_jiffies(20));
 	else
 		queue_delayed_work(iavf_wq, &adapter->watchdog_task, HZ * 2);
-	queue_work(iavf_wq, &adapter->adminq_task);
 }
 
+/**
+ * iavf_disable_vf - disable VF
+ * @adapter: board private structure
+ *
+ * Set communication failed flag and free all resources.
+ * NOTE: This function is expected to be called with crit_lock being held.
+ **/
 static void iavf_disable_vf(struct iavf_adapter *adapter)
 {
 	struct iavf_mac_filter *f, *ftmp;
@@ -2074,14 +2259,12 @@
 
 	iavf_free_misc_irq(adapter);
 	iavf_reset_interrupt_capability(adapter);
-	iavf_free_queues(adapter);
 	iavf_free_q_vectors(adapter);
+	iavf_free_queues(adapter);
 	memset(adapter->vf_res, 0, IAVF_VIRTCHNL_VF_RESOURCE_SIZE);
 	iavf_shutdown_adminq(&adapter->hw);
-	adapter->netdev->flags &= ~IFF_UP;
-	mutex_unlock(&adapter->crit_lock);
 	adapter->flags &= ~IAVF_FLAG_RESET_PENDING;
-	adapter->state = __IAVF_DOWN;
+	iavf_change_state(adapter, __IAVF_DOWN);
 	wake_up(&adapter->down_waitqueue);
 	dev_info(&adapter->pdev->dev, "Reset task did not complete, VF disabled\n");
 }
@@ -2103,22 +2286,26 @@
 	struct net_device *netdev = adapter->netdev;
 	struct iavf_hw *hw = &adapter->hw;
 	struct iavf_mac_filter *f, *ftmp;
-	struct iavf_vlan_filter *vlf;
 	struct iavf_cloud_filter *cf;
 	u32 reg_val;
 	int i = 0, err;
 	bool running;
 
+	/* Detach interface to avoid subsequent NDO callbacks */
+	rtnl_lock();
+	netif_device_detach(netdev);
+	rtnl_unlock();
+
 	/* When device is being removed it doesn't make sense to run the reset
 	 * task, just return in such a case.
 	 */
-	if (mutex_is_locked(&adapter->remove_lock))
-		return;
+	if (!mutex_trylock(&adapter->crit_lock)) {
+		if (adapter->state != __IAVF_REMOVE)
+			queue_work(iavf_wq, &adapter->reset_task);
 
-	if (iavf_lock_timeout(&adapter->crit_lock, 200)) {
-		schedule_work(&adapter->reset_task);
-		return;
+		goto reset_finish;
 	}
+
 	while (!mutex_trylock(&adapter->client_lock))
 		usleep_range(500, 1000);
 	if (CLIENT_ENABLED(adapter)) {
@@ -2166,12 +2353,19 @@
 	}
 
 	pci_set_master(adapter->pdev);
+	pci_restore_msi_state(adapter->pdev);
 
 	if (i == IAVF_RESET_WAIT_COMPLETE_COUNT) {
 		dev_err(&adapter->pdev->dev, "Reset never finished (%x)\n",
 			reg_val);
 		iavf_disable_vf(adapter);
 		mutex_unlock(&adapter->client_lock);
+		mutex_unlock(&adapter->crit_lock);
+		if (netif_running(netdev)) {
+			rtnl_lock();
+			dev_close(netdev);
+			rtnl_unlock();
+		}
 		return; /* Do not attempt to reinit. It's dead, Jim. */
 	}
 
@@ -2180,8 +2374,7 @@
 	 * ndo_open() returning, so we can't assume it means all our open
 	 * tasks have finished, since we're not holding the rtnl_lock here.
 	 */
-	running = ((adapter->state == __IAVF_RUNNING) ||
-		   (adapter->state == __IAVF_RESETTING));
+	running = adapter->state == __IAVF_RUNNING;
 
 	if (running) {
 		netif_carrier_off(netdev);
@@ -2191,7 +2384,7 @@
 	}
 	iavf_irq_disable(adapter);
 
-	adapter->state = __IAVF_RESETTING;
+	iavf_change_state(adapter, __IAVF_RESETTING);
 	adapter->flags &= ~IAVF_FLAG_RESET_PENDING;
 
 	/* free the Tx/Rx rings and descriptors, might be better to just
@@ -2243,11 +2436,6 @@
 	list_for_each_entry(f, &adapter->mac_filter_list, list) {
 		f->add = true;
 	}
-	/* re-add all VLAN filters */
-	list_for_each_entry(vlf, &adapter->vlan_filter_list, list) {
-		vlf->add = true;
-	}
-
 	spin_unlock_bh(&adapter->mac_vlan_list_lock);
 
 	/* check if TCs are running and re-add all cloud filters */
@@ -2261,7 +2449,6 @@
 	spin_unlock_bh(&adapter->cloud_filter_list_lock);
 
 	adapter->aq_required |= IAVF_FLAG_AQ_ADD_MAC_FILTER;
-	adapter->aq_required |= IAVF_FLAG_AQ_ADD_VLAN_FILTER;
 	adapter->aq_required |= IAVF_FLAG_AQ_ADD_CLOUD_FILTER;
 	iavf_misc_irq_enable(adapter);
 
@@ -2291,22 +2478,44 @@
 
 		iavf_configure(adapter);
 
+		/* iavf_up_complete() will switch device back
+		 * to __IAVF_RUNNING
+		 */
 		iavf_up_complete(adapter);
 
 		iavf_irq_enable(adapter, true);
 	} else {
-		adapter->state = __IAVF_DOWN;
+		iavf_change_state(adapter, __IAVF_DOWN);
 		wake_up(&adapter->down_waitqueue);
 	}
 	mutex_unlock(&adapter->client_lock);
 	mutex_unlock(&adapter->crit_lock);
 
-	return;
+	goto reset_finish;
 reset_err:
+	if (running) {
+		set_bit(__IAVF_VSI_DOWN, adapter->vsi.state);
+		iavf_free_traffic_irqs(adapter);
+	}
+	iavf_disable_vf(adapter);
+
 	mutex_unlock(&adapter->client_lock);
 	mutex_unlock(&adapter->crit_lock);
+
+	if (netif_running(netdev)) {
+		/* Close device to ensure that Tx queues will not be started
+		 * during netif_device_attach() at the end of the reset task.
+		 */
+		rtnl_lock();
+		dev_close(netdev);
+		rtnl_unlock();
+	}
+
 	dev_err(&adapter->pdev->dev, "failed to allocate resources during reinit\n");
-	iavf_close(netdev);
+reset_finish:
+	rtnl_lock();
+	netif_device_attach(netdev);
+	rtnl_unlock();
 }
 
 /**
@@ -2324,16 +2533,22 @@
 	u32 val, oldval;
 	u16 pending;
 
-	if (adapter->flags & IAVF_FLAG_PF_COMMS_FAILED)
+	if (!mutex_trylock(&adapter->crit_lock)) {
+		if (adapter->state == __IAVF_REMOVE)
+			return;
+
+		queue_work(iavf_wq, &adapter->adminq_task);
 		goto out;
+	}
+
+	if (adapter->flags & IAVF_FLAG_PF_COMMS_FAILED)
+		goto unlock;
 
 	event.buf_len = IAVF_MAX_AQ_BUF_SIZE;
 	event.msg_buf = kzalloc(event.buf_len, GFP_KERNEL);
 	if (!event.msg_buf)
-		goto out;
+		goto unlock;
 
-	if (iavf_lock_timeout(&adapter->crit_lock, 200))
-		goto freedom;
 	do {
 		ret = iavf_clean_arq_element(hw, &event, &pending);
 		v_op = (enum virtchnl_ops)le32_to_cpu(event.desc.cookie_high);
@@ -2347,8 +2562,19 @@
 		if (pending != 0)
 			memset(event.msg_buf, 0, IAVF_MAX_AQ_BUF_SIZE);
 	} while (pending);
-	mutex_unlock(&adapter->crit_lock);
 
+	if ((adapter->flags & IAVF_FLAG_SETUP_NETDEV_FEATURES)) {
+		if (adapter->netdev_registered ||
+		    !test_bit(__IAVF_IN_REMOVE_TASK, &adapter->crit_section)) {
+			struct net_device *netdev = adapter->netdev;
+
+			rtnl_lock();
+			netdev_update_features(netdev);
+			rtnl_unlock();
+		}
+
+		adapter->flags &= ~IAVF_FLAG_SETUP_NETDEV_FEATURES;
+	}
 	if ((adapter->flags &
 	     (IAVF_FLAG_RESET_PENDING | IAVF_FLAG_RESET_NEEDED)) ||
 	    adapter->state == __IAVF_RESETTING)
@@ -2356,7 +2582,7 @@
 
 	/* check for error indications */
 	val = rd32(hw, hw->aq.arq.len);
-	if (val == 0xdeadbeef) /* indicates device in reset */
+	if (val == 0xdeadbeef || val == 0xffffffff) /* device in reset */
 		goto freedom;
 	oldval = val;
 	if (val & IAVF_VF_ARQLEN1_ARQVFE_MASK) {
@@ -2393,6 +2619,8 @@
 
 freedom:
 	kfree(event.msg_buf);
+unlock:
+	mutex_unlock(&adapter->crit_lock);
 out:
 	/* re-enable Admin queue interrupt cause */
 	iavf_misc_irq_enable(adapter);
@@ -2601,6 +2829,7 @@
 				   struct tc_mqprio_qopt_offload *mqprio_qopt)
 {
 	u64 total_max_rate = 0;
+	u32 tx_rate_rem = 0;
 	int i, num_qps = 0;
 	u64 tx_rate = 0;
 	int ret = 0;
@@ -2615,17 +2844,40 @@
 			return -EINVAL;
 		if (mqprio_qopt->min_rate[i]) {
 			dev_err(&adapter->pdev->dev,
-				"Invalid min tx rate (greater than 0) specified\n");
+				"Invalid min tx rate (greater than 0) specified for TC%d\n",
+				i);
 			return -EINVAL;
 		}
-		/*convert to Mbps */
+
+		/* convert to Mbps */
 		tx_rate = div_u64(mqprio_qopt->max_rate[i],
 				  IAVF_MBPS_DIVISOR);
+
+		if (mqprio_qopt->max_rate[i] &&
+		    tx_rate < IAVF_MBPS_QUANTA) {
+			dev_err(&adapter->pdev->dev,
+				"Invalid max tx rate for TC%d, minimum %dMbps\n",
+				i, IAVF_MBPS_QUANTA);
+			return -EINVAL;
+		}
+
+		(void)div_u64_rem(tx_rate, IAVF_MBPS_QUANTA, &tx_rate_rem);
+
+		if (tx_rate_rem != 0) {
+			dev_err(&adapter->pdev->dev,
+				"Invalid max tx rate for TC%d, not divisible by %d\n",
+				i, IAVF_MBPS_QUANTA);
+			return -EINVAL;
+		}
+
 		total_max_rate += tx_rate;
 		num_qps += mqprio_qopt->qopt.count[i];
 	}
-	if (num_qps > IAVF_MAX_REQ_QUEUES)
+	if (num_qps > adapter->num_active_queues) {
+		dev_err(&adapter->pdev->dev,
+			"Cannot support requested number of queues\n");
 		return -EINVAL;
+	}
 
 	ret = iavf_validate_tx_bandwidth(adapter, total_max_rate);
 	return ret;
@@ -2650,6 +2902,34 @@
 }
 
 /**
+ * iavf_is_tc_config_same - Compare the mqprio TC config with the
+ * TC config already configured on this adapter.
+ * @adapter: board private structure
+ * @mqprio_qopt: TC config received from kernel.
+ *
+ * This function compares the TC config received from the kernel
+ * with the config already configured on the adapter.
+ *
+ * Return: True if configuration is same, false otherwise.
+ **/
+static bool iavf_is_tc_config_same(struct iavf_adapter *adapter,
+				   struct tc_mqprio_qopt *mqprio_qopt)
+{
+	struct virtchnl_channel_info *ch = &adapter->ch_config.ch_info[0];
+	int i;
+
+	if (adapter->num_tc != mqprio_qopt->num_tc)
+		return false;
+
+	for (i = 0; i < adapter->num_tc; i++) {
+		if (ch[i].count != mqprio_qopt->count[i] ||
+		    ch[i].offset != mqprio_qopt->offset[i])
+			return false;
+	}
+	return true;
+}
+
+/**
  * __iavf_setup_tc - configure multiple traffic classes
  * @netdev: network interface device structure
  * @type_data: tc offload data
@@ -2684,6 +2964,7 @@
 			netif_tx_disable(netdev);
 			iavf_del_all_cloud_filters(adapter);
 			adapter->aq_required = IAVF_FLAG_AQ_DISABLE_CHANNELS;
+			total_qps = adapter->orig_num_active_queues;
 			goto exit;
 		} else {
 			return -EINVAL;
@@ -2705,7 +2986,7 @@
 		if (ret)
 			return ret;
 		/* Return if same TC config is requested */
-		if (adapter->num_tc == num_tc)
+		if (iavf_is_tc_config_same(adapter, &mqprio_qopt->qopt))
 			return 0;
 		adapter->num_tc = num_tc;
 
@@ -2727,7 +3008,21 @@
 				adapter->ch_config.ch_info[i].offset = 0;
 			}
 		}
+
+		/* Take snapshot of original config such as "num_active_queues"
+		 * It is used later when delete ADQ flow is exercised, so that
+		 * once delete ADQ flow completes, VF shall go back to its
+		 * original queue configuration
+		 */
+
+		adapter->orig_num_active_queues = adapter->num_active_queues;
+
+		/* Store queue info based on TC so that VF gets configured
+		 * with correct number of queues when VF completes ADQ config
+		 * flow
+		 */
 		adapter->ch_config.total_qps = total_qps;
+
 		netif_tx_stop_all_queues(netdev);
 		netif_tx_disable(netdev);
 		adapter->aq_required |= IAVF_FLAG_AQ_ENABLE_CHANNELS;
@@ -2744,6 +3039,12 @@
 		}
 	}
 exit:
+	if (test_bit(__IAVF_IN_REMOVE_TASK, &adapter->crit_section))
+		return 0;
+
+	netif_set_real_num_rx_queues(netdev, total_qps);
+	netif_set_real_num_tx_queues(netdev, total_qps);
+
 	return ret;
 }
 
@@ -2826,7 +3127,7 @@
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad ether dest mask %pM\n",
 					match.mask->dst);
-				return IAVF_ERR_CONFIG;
+				return -EINVAL;
 			}
 		}
 
@@ -2836,7 +3137,7 @@
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad ether src mask %pM\n",
 					match.mask->src);
-				return IAVF_ERR_CONFIG;
+				return -EINVAL;
 			}
 		}
 
@@ -2871,7 +3172,7 @@
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad vlan mask %u\n",
 					match.mask->vlan_id);
-				return IAVF_ERR_CONFIG;
+				return -EINVAL;
 			}
 		}
 		vf->mask.tcp_spec.vlan_id |= cpu_to_be16(0xffff);
@@ -2895,7 +3196,7 @@
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad ip dst mask 0x%08x\n",
 					be32_to_cpu(match.mask->dst));
-				return IAVF_ERR_CONFIG;
+				return -EINVAL;
 			}
 		}
 
@@ -2904,14 +3205,14 @@
 				field_flags |= IAVF_CLOUD_FIELD_IIP;
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad ip src mask 0x%08x\n",
-					be32_to_cpu(match.mask->dst));
-				return IAVF_ERR_CONFIG;
+					be32_to_cpu(match.mask->src));
+				return -EINVAL;
 			}
 		}
 
 		if (field_flags & IAVF_CLOUD_FIELD_TEN_ID) {
 			dev_info(&adapter->pdev->dev, "Tenant id not allowed for ip filter\n");
-			return IAVF_ERR_CONFIG;
+			return -EINVAL;
 		}
 		if (match.key->dst) {
 			vf->mask.tcp_spec.dst_ip[0] |= cpu_to_be32(0xffffffff);
@@ -2932,7 +3233,7 @@
 		if (ipv6_addr_any(&match.mask->dst)) {
 			dev_err(&adapter->pdev->dev, "Bad ipv6 dst mask 0x%02x\n",
 				IPV6_ADDR_ANY);
-			return IAVF_ERR_CONFIG;
+			return -EINVAL;
 		}
 
 		/* src and dest IPv6 address should not be LOOPBACK
@@ -2942,7 +3243,7 @@
 		    ipv6_addr_loopback(&match.key->src)) {
 			dev_err(&adapter->pdev->dev,
 				"ipv6 addr should not be loopback\n");
-			return IAVF_ERR_CONFIG;
+			return -EINVAL;
 		}
 		if (!ipv6_addr_any(&match.mask->dst) ||
 		    !ipv6_addr_any(&match.mask->src))
@@ -2967,7 +3268,7 @@
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad src port mask %u\n",
 					be16_to_cpu(match.mask->src));
-				return IAVF_ERR_CONFIG;
+				return -EINVAL;
 			}
 		}
 
@@ -2977,7 +3278,7 @@
 			} else {
 				dev_err(&adapter->pdev->dev, "Bad dst port mask %u\n",
 					be16_to_cpu(match.mask->dst));
-				return IAVF_ERR_CONFIG;
+				return -EINVAL;
 			}
 		}
 		if (match.key->dst) {
@@ -3041,8 +3342,10 @@
 		return -ENOMEM;
 
 	while (!mutex_trylock(&adapter->crit_lock)) {
-		if (--count == 0)
-			goto err;
+		if (--count == 0) {
+			kfree(filter);
+			return err;
+		}
 		udelay(1);
 	}
 
@@ -3053,11 +3356,11 @@
 	/* start out with flow type and eth type IPv4 to begin with */
 	filter->f.flow_type = VIRTCHNL_TCP_V4_FLOW;
 	err = iavf_parse_cls_flower(adapter, cls_flower, filter);
-	if (err < 0)
+	if (err)
 		goto err;
 
 	err = iavf_handle_tclass(adapter, tc, filter);
-	if (err < 0)
+	if (err)
 		goto err;
 
 	/* add filter to the list */
@@ -3226,6 +3529,13 @@
 		goto err_unlock;
 	}
 
+	if (adapter->state == __IAVF_RUNNING &&
+	    !test_bit(__IAVF_VSI_DOWN, adapter->vsi.state)) {
+		dev_dbg(&adapter->pdev->dev, "VF is already open.\n");
+		err = 0;
+		goto err_unlock;
+	}
+
 	/* allocate transmit descriptors */
 	err = iavf_setup_all_tx_resources(adapter);
 	if (err)
@@ -3247,6 +3557,9 @@
 
 	spin_unlock_bh(&adapter->mac_vlan_list_lock);
 
+	/* Restore VLAN filters that were removed with IFF_DOWN */
+	iavf_restore_filters(adapter);
+
 	iavf_configure(adapter);
 
 	iavf_up_complete(adapter);
@@ -3284,20 +3597,45 @@
 static int iavf_close(struct net_device *netdev)
 {
 	struct iavf_adapter *adapter = netdev_priv(netdev);
+	u64 aq_to_restore;
 	int status;
 
-	if (adapter->state <= __IAVF_DOWN_PENDING)
-		return 0;
+	mutex_lock(&adapter->crit_lock);
 
-	while (!mutex_trylock(&adapter->crit_lock))
-		usleep_range(500, 1000);
+	if (adapter->state <= __IAVF_DOWN_PENDING) {
+		mutex_unlock(&adapter->crit_lock);
+		return 0;
+	}
 
 	set_bit(__IAVF_VSI_DOWN, adapter->vsi.state);
 	if (CLIENT_ENABLED(adapter))
 		adapter->flags |= IAVF_FLAG_CLIENT_NEEDS_CLOSE;
+	/* We cannot send IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS before
+	 * IAVF_FLAG_AQ_DISABLE_QUEUES because in such case there is rtnl
+	 * deadlock with adminq_task() until iavf_close timeouts. We must send
+	 * IAVF_FLAG_AQ_GET_CONFIG before IAVF_FLAG_AQ_DISABLE_QUEUES to make
+	 * disable queues possible for vf. Give only necessary flags to
+	 * iavf_down and save other to set them right before iavf_close()
+	 * returns, when IAVF_FLAG_AQ_DISABLE_QUEUES will be already sent and
+	 * iavf will be in DOWN state.
+	 */
+	aq_to_restore = adapter->aq_required;
+	adapter->aq_required &= IAVF_FLAG_AQ_GET_CONFIG;
+
+	/* Remove flags which we do not want to send after close or we want to
+	 * send before disable queues.
+	 */
+	aq_to_restore &= ~(IAVF_FLAG_AQ_GET_CONFIG		|
+			   IAVF_FLAG_AQ_ENABLE_QUEUES		|
+			   IAVF_FLAG_AQ_CONFIGURE_QUEUES	|
+			   IAVF_FLAG_AQ_ADD_VLAN_FILTER		|
+			   IAVF_FLAG_AQ_ADD_MAC_FILTER		|
+			   IAVF_FLAG_AQ_ADD_CLOUD_FILTER	|
+			   IAVF_FLAG_AQ_ADD_FDIR_FILTER		|
+			   IAVF_FLAG_AQ_ADD_ADV_RSS_CFG);
 
 	iavf_down(adapter);
-	adapter->state = __IAVF_DOWN_PENDING;
+	iavf_change_state(adapter, __IAVF_DOWN_PENDING);
 	iavf_free_traffic_irqs(adapter);
 
 	mutex_unlock(&adapter->crit_lock);
@@ -3318,6 +3656,10 @@
 				    msecs_to_jiffies(500));
 	if (!status)
 		netdev_warn(netdev, "Device resources not yet released\n");
+
+	mutex_lock(&adapter->crit_lock);
+	adapter->aq_required |= aq_to_restore;
+	mutex_unlock(&adapter->crit_lock);
 	return 0;
 }
 
@@ -3337,8 +3679,11 @@
 		iavf_notify_client_l2_params(&adapter->vsi);
 		adapter->flags |= IAVF_FLAG_SERVICE_CLIENT_REQUESTED;
 	}
-	adapter->flags |= IAVF_FLAG_RESET_NEEDED;
-	queue_work(iavf_wq, &adapter->reset_task);
+
+	if (netif_running(netdev)) {
+		adapter->flags |= IAVF_FLAG_RESET_NEEDED;
+		queue_work(iavf_wq, &adapter->reset_task);
+	}
 
 	return 0;
 }
@@ -3354,11 +3699,16 @@
 {
 	struct iavf_adapter *adapter = netdev_priv(netdev);
 
-	/* Don't allow changing VLAN_RX flag when adapter is not capable
-	 * of VLAN offload
+	/* Don't allow enabling VLAN features when adapter is not capable
+	 * of VLAN offload/filtering
 	 */
 	if (!VLAN_ALLOWED(adapter)) {
-		if ((netdev->features ^ features) & NETIF_F_HW_VLAN_CTAG_RX)
+		netdev->hw_features &= ~(NETIF_F_HW_VLAN_CTAG_RX |
+					 NETIF_F_HW_VLAN_CTAG_TX |
+					 NETIF_F_HW_VLAN_CTAG_FILTER);
+		if (features & (NETIF_F_HW_VLAN_CTAG_RX |
+				NETIF_F_HW_VLAN_CTAG_TX |
+				NETIF_F_HW_VLAN_CTAG_FILTER))
 			return -EINVAL;
 	} else if ((netdev->features ^ features) & NETIF_F_HW_VLAN_CTAG_RX) {
 		if (features & NETIF_F_HW_VLAN_CTAG_RX)
@@ -3442,7 +3792,8 @@
 {
 	struct iavf_adapter *adapter = netdev_priv(netdev);
 
-	if (!(adapter->vf_res->vf_cap_flags & VIRTCHNL_VF_OFFLOAD_VLAN))
+	if (adapter->vf_res &&
+	    !(adapter->vf_res->vf_cap_flags & VIRTCHNL_VF_OFFLOAD_VLAN))
 		features &= ~(NETIF_F_HW_VLAN_CTAG_TX |
 			      NETIF_F_HW_VLAN_CTAG_RX |
 			      NETIF_F_HW_VLAN_CTAG_FILTER);
@@ -3631,71 +3982,13 @@
 }
 
 /**
- * iavf_init_task - worker thread to perform delayed initialization
- * @work: pointer to work_struct containing our data
- *
- * This task completes the work that was begun in probe. Due to the nature
- * of VF-PF communications, we may need to wait tens of milliseconds to get
- * responses back from the PF. Rather than busy-wait in probe and bog down the
- * whole system, we'll do it in a task so we can sleep.
- * This task only runs during driver init. Once we've established
- * communications with the PF driver and set up our netdev, the watchdog
- * takes over.
- **/
-static void iavf_init_task(struct work_struct *work)
-{
-	struct iavf_adapter *adapter = container_of(work,
-						    struct iavf_adapter,
-						    init_task.work);
-	struct iavf_hw *hw = &adapter->hw;
-
-	if (iavf_lock_timeout(&adapter->crit_lock, 5000)) {
-		dev_warn(&adapter->pdev->dev, "failed to acquire crit_lock in %s\n", __FUNCTION__);
-		return;
-	}
-	switch (adapter->state) {
-	case __IAVF_STARTUP:
-		if (iavf_startup(adapter) < 0)
-			goto init_failed;
-		break;
-	case __IAVF_INIT_VERSION_CHECK:
-		if (iavf_init_version_check(adapter) < 0)
-			goto init_failed;
-		break;
-	case __IAVF_INIT_GET_RESOURCES:
-		if (iavf_init_get_resources(adapter) < 0)
-			goto init_failed;
-		goto out;
-	default:
-		goto init_failed;
-	}
-
-	queue_delayed_work(iavf_wq, &adapter->init_task,
-			   msecs_to_jiffies(30));
-	goto out;
-init_failed:
-	if (++adapter->aq_wait_count > IAVF_AQ_MAX_ERR) {
-		dev_err(&adapter->pdev->dev,
-			"Failed to communicate with PF; waiting before retry\n");
-		adapter->flags |= IAVF_FLAG_PF_COMMS_FAILED;
-		iavf_shutdown_adminq(hw);
-		adapter->state = __IAVF_STARTUP;
-		queue_delayed_work(iavf_wq, &adapter->init_task, HZ * 5);
-		goto out;
-	}
-	queue_delayed_work(iavf_wq, &adapter->init_task, HZ);
-out:
-	mutex_unlock(&adapter->crit_lock);
-}
-
-/**
  * iavf_shutdown - Shutdown the device in preparation for a reboot
  * @pdev: pci device structure
  **/
 static void iavf_shutdown(struct pci_dev *pdev)
 {
-	struct net_device *netdev = pci_get_drvdata(pdev);
-	struct iavf_adapter *adapter = netdev_priv(netdev);
+	struct iavf_adapter *adapter = iavf_pdev_to_adapter(pdev);
+	struct net_device *netdev = adapter->netdev;
 
 	netif_device_detach(netdev);
 
@@ -3705,7 +3998,7 @@
 	if (iavf_lock_timeout(&adapter->crit_lock, 5000))
 		dev_warn(&adapter->pdev->dev, "failed to acquire crit_lock in %s\n", __FUNCTION__);
 	/* Prevent the watchdog from running. */
-	adapter->state = __IAVF_REMOVE;
+	iavf_change_state(adapter, __IAVF_REMOVE);
 	adapter->aq_required = 0;
 	mutex_unlock(&adapter->crit_lock);
 
@@ -3778,7 +4071,7 @@
 	hw->back = adapter;
 
 	adapter->msg_enable = BIT(DEFAULT_DEBUG_LEVEL_SHIFT) - 1;
-	adapter->state = __IAVF_STARTUP;
+	iavf_change_state(adapter, __IAVF_STARTUP);
 
 	/* Call save state here because it relies on the adapter struct. */
 	pci_save_state(pdev);
@@ -3803,7 +4096,6 @@
 	 */
 	mutex_init(&adapter->crit_lock);
 	mutex_init(&adapter->client_lock);
-	mutex_init(&adapter->remove_lock);
 	mutex_init(&hw->aq.asq_mutex);
 	mutex_init(&hw->aq.arq_mutex);
 
@@ -3822,8 +4114,7 @@
 	INIT_WORK(&adapter->adminq_task, iavf_adminq_task);
 	INIT_DELAYED_WORK(&adapter->watchdog_task, iavf_watchdog_task);
 	INIT_DELAYED_WORK(&adapter->client_task, iavf_client_task);
-	INIT_DELAYED_WORK(&adapter->init_task, iavf_init_task);
-	queue_delayed_work(iavf_wq, &adapter->init_task,
+	queue_delayed_work(iavf_wq, &adapter->watchdog_task,
 			   msecs_to_jiffies(5 * (pdev->devfn & 0x07)));
 
 	/* Setup the wait queue for indicating transition to down status */
@@ -3880,10 +4171,11 @@
 static int __maybe_unused iavf_resume(struct device *dev_d)
 {
 	struct pci_dev *pdev = to_pci_dev(dev_d);
-	struct net_device *netdev = pci_get_drvdata(pdev);
-	struct iavf_adapter *adapter = netdev_priv(netdev);
+	struct iavf_adapter *adapter;
 	u32 err;
 
+	adapter = iavf_pdev_to_adapter(pdev);
+
 	pci_set_master(pdev);
 
 	rtnl_lock();
@@ -3902,7 +4194,7 @@
 
 	queue_work(iavf_wq, &adapter->reset_task);
 
-	netif_device_attach(netdev);
+	netif_device_attach(adapter->netdev);
 
 	return err;
 }
@@ -3918,23 +4210,49 @@
  **/
 static void iavf_remove(struct pci_dev *pdev)
 {
-	struct net_device *netdev = pci_get_drvdata(pdev);
-	struct iavf_adapter *adapter = netdev_priv(netdev);
+	struct iavf_adapter *adapter = iavf_pdev_to_adapter(pdev);
 	struct iavf_fdir_fltr *fdir, *fdirtmp;
 	struct iavf_vlan_filter *vlf, *vlftmp;
+	struct iavf_cloud_filter *cf, *cftmp;
 	struct iavf_adv_rss *rss, *rsstmp;
 	struct iavf_mac_filter *f, *ftmp;
-	struct iavf_cloud_filter *cf, *cftmp;
-	struct iavf_hw *hw = &adapter->hw;
+	struct net_device *netdev;
+	struct iavf_hw *hw;
 	int err;
-	/* Indicate we are in remove and not to run reset_task */
-	mutex_lock(&adapter->remove_lock);
-	cancel_delayed_work_sync(&adapter->init_task);
-	cancel_work_sync(&adapter->reset_task);
-	cancel_delayed_work_sync(&adapter->client_task);
+
+	netdev = adapter->netdev;
+	hw = &adapter->hw;
+
+	if (test_and_set_bit(__IAVF_IN_REMOVE_TASK, &adapter->crit_section))
+		return;
+
+	/* Wait until port initialization is complete.
+	 * There are flows where register/unregister netdev may race.
+	 */
+	while (1) {
+		mutex_lock(&adapter->crit_lock);
+		if (adapter->state == __IAVF_RUNNING ||
+		    adapter->state == __IAVF_DOWN ||
+		    adapter->state == __IAVF_INIT_FAILED) {
+			mutex_unlock(&adapter->crit_lock);
+			break;
+		}
+		/* Simply return if we already went through iavf_shutdown */
+		if (adapter->state == __IAVF_REMOVE) {
+			mutex_unlock(&adapter->crit_lock);
+			return;
+		}
+
+		mutex_unlock(&adapter->crit_lock);
+		usleep_range(500, 1000);
+	}
+	cancel_delayed_work_sync(&adapter->watchdog_task);
+
 	if (adapter->netdev_registered) {
-		unregister_netdev(netdev);
+		rtnl_lock();
+		unregister_netdevice(netdev);
 		adapter->netdev_registered = false;
+		rtnl_unlock();
 	}
 	if (CLIENT_ALLOWED(adapter)) {
 		err = iavf_lan_del_device(adapter);
@@ -3943,6 +4261,10 @@
 				 err);
 	}
 
+	mutex_lock(&adapter->crit_lock);
+	dev_info(&adapter->pdev->dev, "Remove device\n");
+	iavf_change_state(adapter, __IAVF_REMOVE);
+
 	iavf_request_reset(adapter);
 	msleep(50);
 	/* If the FW isn't responding, kick it once, but only once. */
@@ -3950,24 +4272,24 @@
 		iavf_request_reset(adapter);
 		msleep(50);
 	}
-	if (iavf_lock_timeout(&adapter->crit_lock, 5000))
-		dev_warn(&adapter->pdev->dev, "failed to acquire crit_lock in %s\n", __FUNCTION__);
 
+	iavf_misc_irq_disable(adapter);
 	/* Shut down all the garbage mashers on the detention level */
-	adapter->state = __IAVF_REMOVE;
+	cancel_work_sync(&adapter->reset_task);
+	cancel_delayed_work_sync(&adapter->watchdog_task);
+	cancel_work_sync(&adapter->adminq_task);
+	cancel_delayed_work_sync(&adapter->client_task);
+
 	adapter->aq_required = 0;
 	adapter->flags &= ~IAVF_FLAG_REINIT_ITR_NEEDED;
+
 	iavf_free_all_tx_resources(adapter);
 	iavf_free_all_rx_resources(adapter);
-	iavf_misc_irq_disable(adapter);
 	iavf_free_misc_irq(adapter);
+
 	iavf_reset_interrupt_capability(adapter);
 	iavf_free_q_vectors(adapter);
 
-	cancel_delayed_work_sync(&adapter->watchdog_task);
-
-	cancel_work_sync(&adapter->adminq_task);
-
 	iavf_free_rss(adapter);
 
 	if (hw->aq.asq.count)
@@ -3979,8 +4301,6 @@
 	mutex_destroy(&adapter->client_lock);
 	mutex_unlock(&adapter->crit_lock);
 	mutex_destroy(&adapter->crit_lock);
-	mutex_unlock(&adapter->remove_lock);
-	mutex_destroy(&adapter->remove_lock);
 
 	iounmap(hw->hw_addr);
 	pci_release_regions(pdev);
@@ -4062,7 +4382,11 @@
 		pr_err("%s: Failed to create workqueue\n", iavf_driver_name);
 		return -ENOMEM;
 	}
+
 	ret = pci_register_driver(&iavf_driver);
+	if (ret)
+		destroy_workqueue(iavf_wq);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_register.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_register.h
@@ -40,7 +40,7 @@
 #define IAVF_VFINT_DYN_CTL01_INTENA_MASK IAVF_MASK(0x1, IAVF_VFINT_DYN_CTL01_INTENA_SHIFT)
 #define IAVF_VFINT_DYN_CTL01_ITR_INDX_SHIFT 3
 #define IAVF_VFINT_DYN_CTL01_ITR_INDX_MASK IAVF_MASK(0x3, IAVF_VFINT_DYN_CTL01_ITR_INDX_SHIFT)
-#define IAVF_VFINT_DYN_CTLN1(_INTVF) (0x00003800 + ((_INTVF) * 4)) /* _i=0...15 */ /* Reset: VFR */
+#define IAVF_VFINT_DYN_CTLN1(_INTVF) (0x00003800 + ((_INTVF) * 4)) /* _i=0...63 */ /* Reset: VFR */
 #define IAVF_VFINT_DYN_CTLN1_INTENA_SHIFT 0
 #define IAVF_VFINT_DYN_CTLN1_INTENA_MASK IAVF_MASK(0x1, IAVF_VFINT_DYN_CTLN1_INTENA_SHIFT)
 #define IAVF_VFINT_DYN_CTLN1_SWINT_TRIG_SHIFT 2
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_txrx.c
@@ -114,8 +114,11 @@
 {
 	u32 head, tail;
 
+	/* underlying hardware might not allow access and/or always return
+	 * 0 for the head/tail registers so just use the cached values
+	 */
 	head = ring->next_to_clean;
-	tail = readl(ring->tail);
+	tail = ring->next_to_use;
 
 	if (head != tail)
 		return (head < tail) ?
@@ -1058,7 +1061,7 @@
 		cpu_to_le64((u64)IAVF_RX_DESC_FLTSTAT_RSS_HASH <<
 			    IAVF_RX_DESC_STATUS_FLTSTAT_SHIFT);
 
-	if (ring->netdev->features & NETIF_F_RXHASH)
+	if (!(ring->netdev->features & NETIF_F_RXHASH))
 		return;
 
 	if ((rx_desc->wb.qword1.status_error_len & rss_mask) == rss_mask) {
@@ -1250,11 +1253,10 @@
 {
 	struct iavf_rx_buffer *rx_buffer;
 
-	if (!size)
-		return NULL;
-
 	rx_buffer = &rx_ring->rx_bi[rx_ring->next_to_clean];
 	prefetchw(rx_buffer->page);
+	if (!size)
+		return rx_buffer;
 
 	/* we are reusing so sync this buffer for CPU use */
 	dma_sync_single_range_for_cpu(rx_ring->dev,
@@ -1356,7 +1358,7 @@
 #endif
 	struct sk_buff *skb;
 
-	if (!rx_buffer)
+	if (!rx_buffer || !size)
 		return NULL;
 	/* prefetch first cache line of first page */
 	va = page_address(rx_buffer->page) + rx_buffer->page_offset;
@@ -1514,7 +1516,7 @@
 		/* exit if we failed to retrieve a buffer */
 		if (!skb) {
 			rx_ring->rx_stats.alloc_buff_failed++;
-			if (rx_buffer)
+			if (rx_buffer && size)
 				rx_buffer->pagecnt_bias++;
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
@@ -244,11 +244,14 @@
 void iavf_configure_queues(struct iavf_adapter *adapter)
 {
 	struct virtchnl_vsi_queue_config_info *vqci;
-	struct virtchnl_queue_pair_info *vqpi;
+	int i, max_frame = adapter->vf_res->max_mtu;
 	int pairs = adapter->num_active_queues;
-	int i, max_frame = IAVF_MAX_RXBUFFER;
+	struct virtchnl_queue_pair_info *vqpi;
 	size_t len;
 
+	if (max_frame > IAVF_MAX_RXBUFFER || !max_frame)
+		max_frame = IAVF_MAX_RXBUFFER;
+
 	if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
 		/* bail because we already have a command pending */
 		dev_err(&adapter->pdev->dev, "Cannot configure queues, command %d pending\n",
@@ -607,7 +610,7 @@
 		if (f->add)
 			count++;
 	}
-	if (!count) {
+	if (!count || !VLAN_ALLOWED(adapter)) {
 		adapter->aq_required &= ~IAVF_FLAG_AQ_ADD_VLAN_FILTER;
 		spin_unlock_bh(&adapter->mac_vlan_list_lock);
 		return;
@@ -673,9 +676,19 @@
 
 	spin_lock_bh(&adapter->mac_vlan_list_lock);
 
-	list_for_each_entry(f, &adapter->vlan_filter_list, list) {
-		if (f->remove)
+	list_for_each_entry_safe(f, ftmp, &adapter->vlan_filter_list, list) {
+		/* since VLAN capabilities are not allowed, we dont want to send
+		 * a VLAN delete request because it will most likely fail and
+		 * create unnecessary errors/noise, so just free the VLAN
+		 * filters marked for removal to enable bailing out before
+		 * sending a virtchnl message
+		 */
+		if (f->remove && !VLAN_ALLOWED(adapter)) {
+			list_del(&f->list);
+			kfree(f);
+		} else if (f->remove) {
 			count++;
+		}
 	}
 	if (!count) {
 		adapter->aq_required &= ~IAVF_FLAG_AQ_DEL_VLAN_FILTER;
@@ -784,6 +797,8 @@
 		/* no error message, this isn't crucial */
 		return;
 	}
+
+	adapter->aq_required &= ~IAVF_FLAG_AQ_REQUEST_STATS;
 	adapter->current_op = VIRTCHNL_OP_GET_STATS;
 	vqs.vsi_id = adapter->vsi_res->vsi_id;
 	/* queue maps are ignored for this message - only the vsi is used */
@@ -1449,6 +1464,22 @@
 }
 
 /**
+ * iavf_netdev_features_vlan_strip_set - update vlan strip status
+ * @netdev: ptr to netdev being adjusted
+ * @enable: enable or disable vlan strip
+ *
+ * Helper function to change vlan strip status in netdev->features.
+ */
+static void iavf_netdev_features_vlan_strip_set(struct net_device *netdev,
+						const bool enable)
+{
+	if (enable)
+		netdev->features |= NETIF_F_HW_VLAN_CTAG_RX;
+	else
+		netdev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+}
+
+/**
  * iavf_virtchnl_completion
  * @adapter: adapter structure
  * @v_opcode: opcode sent by PF
@@ -1671,8 +1702,18 @@
 			}
 			break;
 		case VIRTCHNL_OP_ENABLE_VLAN_STRIPPING:
+			dev_warn(&adapter->pdev->dev, "Changing VLAN Stripping is not allowed when Port VLAN is configured\n");
+			/* Vlan stripping could not be enabled by ethtool.
+			 * Disable it in netdev->features.
+			 */
+			iavf_netdev_features_vlan_strip_set(netdev, false);
+			break;
 		case VIRTCHNL_OP_DISABLE_VLAN_STRIPPING:
 			dev_warn(&adapter->pdev->dev, "Changing VLAN Stripping is not allowed when Port VLAN is configured\n");
+			/* Vlan stripping could not be disabled by ethtool.
+			 * Enable it in netdev->features.
+			 */
+			iavf_netdev_features_vlan_strip_set(netdev, true);
 			break;
 		default:
 			dev_err(&adapter->pdev->dev, "PF returned error %d (%s) to our request %d\n",
@@ -1685,7 +1726,7 @@
 		if (!v_retval)
 			iavf_mac_add_ok(adapter);
 		if (!ether_addr_equal(netdev->dev_addr, adapter->hw.mac.addr))
-			ether_addr_copy(netdev->dev_addr, adapter->hw.mac.addr);
+			eth_hw_addr_set(netdev, adapter->hw.mac.addr);
 		break;
 	case VIRTCHNL_OP_GET_STATS: {
 		struct iavf_eth_stats *stats =
@@ -1716,14 +1757,31 @@
 			ether_addr_copy(adapter->hw.mac.addr, netdev->dev_addr);
 		} else {
 			/* refresh current mac address if changed */
-			ether_addr_copy(netdev->dev_addr, adapter->hw.mac.addr);
+			eth_hw_addr_set(netdev, adapter->hw.mac.addr);
 			ether_addr_copy(netdev->perm_addr,
 					adapter->hw.mac.addr);
 		}
 		spin_lock_bh(&adapter->mac_vlan_list_lock);
 		iavf_add_filter(adapter, adapter->hw.mac.addr);
+
+		if (VLAN_ALLOWED(adapter)) {
+			if (!list_empty(&adapter->vlan_filter_list)) {
+				struct iavf_vlan_filter *vlf;
+
+				/* re-add all VLAN filters over virtchnl */
+				list_for_each_entry(vlf,
+						    &adapter->vlan_filter_list,
+						    list)
+					vlf->add = true;
+
+				adapter->aq_required |=
+					IAVF_FLAG_AQ_ADD_VLAN_FILTER;
+			}
+		}
+
 		spin_unlock_bh(&adapter->mac_vlan_list_lock);
 		iavf_process_config(adapter);
+		adapter->flags |= IAVF_FLAG_SETUP_NETDEV_FEATURES;
 		}
 		break;
 	case VIRTCHNL_OP_ENABLE_QUEUES:
@@ -1735,7 +1793,7 @@
 		iavf_free_all_tx_resources(adapter);
 		iavf_free_all_rx_resources(adapter);
 		if (adapter->state == __IAVF_DOWN_PENDING) {
-			adapter->state = __IAVF_DOWN;
+			iavf_change_state(adapter, __IAVF_DOWN);
 			wake_up(&adapter->down_waitqueue);
 		}
 		break;
@@ -1889,6 +1947,20 @@
 		spin_unlock_bh(&adapter->adv_rss_lock);
 		}
 		break;
+	case VIRTCHNL_OP_ENABLE_VLAN_STRIPPING:
+		/* PF enabled vlan strip on this VF.
+		 * Update netdev->features if needed to be in sync with ethtool.
+		 */
+		if (!v_retval)
+			iavf_netdev_features_vlan_strip_set(netdev, true);
+		break;
+	case VIRTCHNL_OP_DISABLE_VLAN_STRIPPING:
+		/* PF disabled vlan strip on this VF.
+		 * Update netdev->features if needed to be in sync with ethtool.
+		 */
+		if (!v_retval)
+			iavf_netdev_features_vlan_strip_set(netdev, false);
+		break;
 	default:
 		if (adapter->current_op && (v_opcode != adapter->current_op))
 			dev_warn(&adapter->pdev->dev, "Expected response %d from PF, received %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice.h
@@ -139,13 +139,10 @@
 #define ice_for_each_q_vector(vsi, i) \
 	for ((i) = 0; (i) < (vsi)->num_q_vectors; (i)++)
 
-#define ICE_UCAST_PROMISC_BITS (ICE_PROMISC_UCAST_TX | ICE_PROMISC_MCAST_TX | \
-				ICE_PROMISC_UCAST_RX | ICE_PROMISC_MCAST_RX)
+#define ICE_UCAST_PROMISC_BITS (ICE_PROMISC_UCAST_TX | ICE_PROMISC_UCAST_RX)
 
 #define ICE_UCAST_VLAN_PROMISC_BITS (ICE_PROMISC_UCAST_TX | \
-				     ICE_PROMISC_MCAST_TX | \
 				     ICE_PROMISC_UCAST_RX | \
-				     ICE_PROMISC_MCAST_RX | \
 				     ICE_PROMISC_VLAN_TX  | \
 				     ICE_PROMISC_VLAN_RX)
 
@@ -158,6 +155,13 @@
 
 #define ice_pf_to_dev(pf) (&((pf)->pdev->dev))
 
+enum ice_feature {
+	ICE_F_DSCP,
+	ICE_F_ROCE_LAG,
+	ICE_F_SRIOV_LAG,
+	ICE_F_MAX
+};
+
 struct ice_txq_meta {
 	u32 q_teid;	/* Tx-scheduler element identifier */
 	u16 q_id;	/* Entry in VSI's txq_map bitmap */
@@ -234,7 +238,6 @@
 	ICE_VFLR_EVENT_PENDING,
 	ICE_FLTR_OVERFLOW_PROMISC,
 	ICE_VF_DIS,
-	ICE_VF_DEINIT_IN_PROGRESS,
 	ICE_CFG_BUSY,
 	ICE_SERVICE_SCHED,
 	ICE_SERVICE_DIS,
@@ -245,6 +248,7 @@
 	ICE_LINK_DEFAULT_OVERRIDE_PENDING,
 	ICE_PHY_INIT_COMPLETE,
 	ICE_FD_VF_FLUSH_CTX,		/* set at FD Rx IRQ or timeout */
+	ICE_AUX_ERR_PENDING,
 	ICE_STATE_NBITS		/* must be last */
 };
 
@@ -306,10 +310,6 @@
 	spinlock_t arfs_lock;	/* protects aRFS hash table and filter state */
 	atomic_t *arfs_last_fltr_id;
 
-	/* devlink port data */
-	struct devlink_port devlink_port;
-	bool devlink_port_registered;
-
 	u16 max_frame;
 	u16 rx_buf_len;
 
@@ -405,6 +405,9 @@
 	ICE_FLAG_VF_TRUE_PROMISC_ENA,
 	ICE_FLAG_MDD_AUTO_RESET_VF,
 	ICE_FLAG_LINK_LENIENT_MODE_ENA,
+	ICE_FLAG_PLUG_AUX_DEV,
+	ICE_FLAG_UNPLUG_AUX_DEV,
+	ICE_FLAG_MTU_CHANGED,
 	ICE_PF_FLAGS_NBITS		/* must be last */
 };
 
@@ -421,6 +424,9 @@
 	struct devlink_region *nvm_region;
 	struct devlink_region *devcaps_region;
 
+	/* devlink port data */
+	struct devlink_port devlink_port;
+
 	/* OS reserved IRQ details */
 	struct msix_entry *msix_entries;
 	struct ice_res_tracker *irq_tracker;
@@ -443,6 +449,7 @@
 	/* used to ratelimit the MDD event logging */
 	unsigned long last_printed_mdd_jiffies;
 	DECLARE_BITMAP(malvfs, ICE_MAX_VF_COUNT);
+	DECLARE_BITMAP(features, ICE_F_MAX);
 	DECLARE_BITMAP(state, ICE_STATE_NBITS);
 	DECLARE_BITMAP(flags, ICE_PF_FLAGS_NBITS);
 	unsigned long *avail_txqs;	/* bitmap to track PF Tx queue usage */
@@ -454,6 +461,7 @@
 	struct mutex avail_q_mutex;	/* protects access to avail_[rx|tx]qs */
 	struct mutex sw_mutex;		/* lock for protecting VSI alloc flow */
 	struct mutex tc_mutex;		/* lock to protect TC changes */
+	struct mutex adev_mutex;	/* lock to protect aux device access */
 	u32 msg_enable;
 	struct ice_ptp ptp;
 	u16 num_rdma_msix;		/* Total MSIX vectors for RDMA driver */
@@ -467,6 +475,7 @@
 	wait_queue_head_t reset_wait_queue;
 
 	u32 hw_csum_rx_error;
+	u32 oicr_err_reg;
 	u16 oicr_idx;		/* Other interrupt cause MSIX vector index */
 	u16 num_avail_sw_msix;	/* remaining MSIX SW vectors left unclaimed */
 	u16 max_pf_txqs;	/* Total Tx queues PF wide */
@@ -553,7 +562,7 @@
 
 static inline bool ice_is_xdp_ena_vsi(struct ice_vsi *vsi)
 {
-	return !!vsi->xdp_prog;
+	return !!READ_ONCE(vsi->xdp_prog);
 }
 
 static inline void ice_set_ring_xdp(struct ice_ring *ring)
@@ -641,7 +650,7 @@
 void ice_set_ethtool_safe_mode_ops(struct net_device *netdev);
 u16 ice_get_avail_txq_count(struct ice_pf *pf);
 u16 ice_get_avail_rxq_count(struct ice_pf *pf);
-int ice_vsi_recfg_qs(struct ice_vsi *vsi, int new_rx, int new_tx);
+int ice_vsi_recfg_qs(struct ice_vsi *vsi, int new_rx, int new_tx, bool locked);
 void ice_update_vsi_stats(struct ice_vsi *vsi);
 void ice_update_pf_stats(struct ice_pf *pf);
 int ice_up(struct ice_vsi *vsi);
@@ -696,7 +705,7 @@
 	if (pf->hw.func_caps.common_cap.rdma && pf->num_rdma_msix) {
 		set_bit(ICE_FLAG_RDMA_ENA, pf->flags);
 		set_bit(ICE_FLAG_AUX_ENA, pf->flags);
-		ice_plug_aux_dev(pf);
+		set_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags);
 	}
 }
 
@@ -706,7 +715,11 @@
  */
 static inline void ice_clear_rdma_cap(struct ice_pf *pf)
 {
-	ice_unplug_aux_dev(pf);
+	/* defer unplug to service task to avoid RTNL lock and
+	 * clear PLUG bit so that pending plugs don't interfere
+	 */
+	clear_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags);
+	set_bit(ICE_FLAG_UNPLUG_AUX_DEV, pf->flags);
 	clear_bit(ICE_FLAG_RDMA_ENA, pf->flags);
 	clear_bit(ICE_FLAG_AUX_ENA, pf->flags);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
@@ -118,6 +118,9 @@
 #define ICE_AQC_CAPS_PENDING_NET_VER			0x004D
 #define ICE_AQC_CAPS_RDMA				0x0051
 #define ICE_AQC_CAPS_NVM_MGMT				0x0080
+#define ICE_AQC_CAPS_FW_LAG_SUPPORT			0x0092
+#define ICE_AQC_BIT_ROCEV2_LAG				0x01
+#define ICE_AQC_BIT_SRIOV_LAG				0x02
 
 	u8 major_ver;
 	u8 minor_ver;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_arfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_arfs.c
@@ -510,7 +510,7 @@
 	struct hlist_head *arfs_fltr_list;
 	unsigned int i;
 
-	if (!vsi || vsi->type != ICE_VSI_PF)
+	if (!vsi || vsi->type != ICE_VSI_PF || ice_is_arfs_active(vsi))
 		return;
 
 	arfs_fltr_list = kzalloc(sizeof(*arfs_fltr_list) * ICE_MAX_ARFS_LIST,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_base.c
@@ -115,6 +115,8 @@
 	q_vector->rx.itr_setting = ICE_DFLT_RX_ITR;
 	q_vector->tx.itr_mode = ITR_DYNAMIC;
 	q_vector->rx.itr_mode = ITR_DYNAMIC;
+	q_vector->tx.type = ICE_TX_CONTAINER;
+	q_vector->rx.type = ICE_RX_CONTAINER;
 
 	if (vsi->type == ICE_VSI_VF)
 		goto out;
@@ -357,7 +359,8 @@
 	/* Receive Packet Data Buffer Size.
 	 * The Packet Data Buffer Size is defined in 128 byte units.
 	 */
-	rlan_ctx.dbuf = ring->rx_buf_len >> ICE_RLAN_CTX_DBUF_S;
+	rlan_ctx.dbuf = DIV_ROUND_UP(ring->rx_buf_len,
+				     BIT_ULL(ICE_RLAN_CTX_DBUF_S));
 
 	/* use 32 byte descriptors */
 	rlan_ctx.dsize = 1;
@@ -909,7 +912,7 @@
 	} else if (status == ICE_ERR_DOES_NOT_EXIST) {
 		dev_dbg(ice_pf_to_dev(vsi->back), "LAN Tx queues do not exist, nothing to disable\n");
 	} else if (status) {
-		dev_err(ice_pf_to_dev(vsi->back), "Failed to disable LAN Tx queues, error: %s\n",
+		dev_dbg(ice_pf_to_dev(vsi->back), "Failed to disable LAN Tx queues, error: %s\n",
 			ice_stat_str(status));
 		return -ENODEV;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_common.c
@@ -2022,6 +2022,14 @@
 		ice_debug(hw, ICE_DBG_INIT, "%s: max_mtu = %d\n",
 			  prefix, caps->max_mtu);
 		break;
+	case ICE_AQC_CAPS_FW_LAG_SUPPORT:
+		caps->roce_lag = !!(number & ICE_AQC_BIT_ROCEV2_LAG);
+		ice_debug(hw, ICE_DBG_INIT, "%s: roce_lag = %u\n",
+			  prefix, caps->roce_lag);
+		caps->sriov_lag = !!(number & ICE_AQC_BIT_SRIOV_LAG);
+		ice_debug(hw, ICE_DBG_INIT, "%s: sriov_lag = %u\n",
+			  prefix, caps->sriov_lag);
+		break;
 	default:
 		/* Not one of the recognized common capabilities */
 		found = false;
@@ -3270,9 +3278,10 @@
 
 	if (fec == ICE_FEC_AUTO && ice_fw_supports_link_override(hw) &&
 	    !ice_fw_supports_report_dflt_cfg(hw)) {
-		struct ice_link_default_override_tlv tlv;
+		struct ice_link_default_override_tlv tlv = { 0 };
 
-		if (ice_get_link_default_override(&tlv, pi))
+		status = ice_get_link_default_override(&tlv, pi);
+		if (status)
 			goto out;
 
 		if (!(tlv.options & ICE_LINK_OVERRIDE_STRICT_MODE) &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
@@ -355,7 +355,7 @@
 		goto out;
 	}
 
-	ice_pf_dcb_recfg(pf);
+	ice_pf_dcb_recfg(pf, false);
 
 out:
 	ice_ena_vsi(pf_vsi, true);
@@ -644,12 +644,13 @@
 /**
  * ice_pf_dcb_recfg - Reconfigure all VEBs and VSIs
  * @pf: pointer to the PF struct
+ * @locked: is adev device lock held
  *
  * Assumed caller has already disabled all VSIs before
  * calling this function. Reconfiguring DCB based on
  * local_dcbx_cfg.
  */
-void ice_pf_dcb_recfg(struct ice_pf *pf)
+void ice_pf_dcb_recfg(struct ice_pf *pf, bool locked)
 {
 	struct ice_dcbx_cfg *dcbcfg = &pf->hw.port_info->qos_cfg.local_dcbx_cfg;
 	struct iidc_event *event;
@@ -688,14 +689,16 @@
 		if (vsi->type == ICE_VSI_PF)
 			ice_dcbnl_set_all(vsi);
 	}
-	/* Notify the AUX drivers that TC change is finished */
-	event = kzalloc(sizeof(*event), GFP_KERNEL);
-	if (!event)
-		return;
+	if (!locked) {
+		/* Notify the AUX drivers that TC change is finished */
+		event = kzalloc(sizeof(*event), GFP_KERNEL);
+		if (!event)
+			return;
 
-	set_bit(IIDC_EVENT_AFTER_TC_CHANGE, event->type);
-	ice_send_event_to_aux(pf, event);
-	kfree(event);
+		set_bit(IIDC_EVENT_AFTER_TC_CHANGE, event->type);
+		ice_send_event_to_aux(pf, event);
+		kfree(event);
+	}
 }
 
 /**
@@ -943,7 +946,7 @@
 	}
 
 	/* changes in configuration update VSI */
-	ice_pf_dcb_recfg(pf);
+	ice_pf_dcb_recfg(pf, false);
 
 	ice_ena_vsi(pf_vsi, true);
 unlock_rtnl:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
@@ -23,7 +23,7 @@
 int
 ice_pf_dcb_cfg(struct ice_pf *pf, struct ice_dcbx_cfg *new_cfg, bool locked);
 int ice_dcb_bwchk(struct ice_pf *pf, struct ice_dcbx_cfg *dcbcfg);
-void ice_pf_dcb_recfg(struct ice_pf *pf);
+void ice_pf_dcb_recfg(struct ice_pf *pf, bool locked);
 void ice_vsi_cfg_dcb_rings(struct ice_vsi *vsi);
 int ice_init_pf_dcb(struct ice_pf *pf, bool locked);
 void ice_update_dcb_stats(struct ice_pf *pf);
@@ -113,7 +113,7 @@
 	return false;
 }
 
-static inline void ice_pf_dcb_recfg(struct ice_pf *pf) { }
+static inline void ice_pf_dcb_recfg(struct ice_pf *pf, bool locked) { }
 static inline void ice_vsi_cfg_dcb_rings(struct ice_vsi *vsi) { }
 static inline void ice_update_dcb_stats(struct ice_pf *pf) { }
 static inline void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_devlink.c
@@ -526,60 +526,115 @@
 }
 
 /**
- * ice_devlink_create_port - Create a devlink port for this VSI
- * @vsi: the VSI to create a port for
+ * ice_devlink_create_pf_port - Create a devlink port for this PF
+ * @pf: the PF to create a devlink port for
  *
- * Create and register a devlink_port for this VSI.
+ * Create and register a devlink_port for this PF.
  *
  * Return: zero on success or an error code on failure.
  */
-int ice_devlink_create_port(struct ice_vsi *vsi)
+int ice_devlink_create_pf_port(struct ice_pf *pf)
 {
 	struct devlink_port_attrs attrs = {};
-	struct ice_port_info *pi;
+	struct devlink_port *devlink_port;
 	struct devlink *devlink;
+	struct ice_vsi *vsi;
 	struct device *dev;
-	struct ice_pf *pf;
 	int err;
 
-	/* Currently we only create devlink_port instances for PF VSIs */
-	if (vsi->type != ICE_VSI_PF)
-		return -EINVAL;
-
-	pf = vsi->back;
-	devlink = priv_to_devlink(pf);
 	dev = ice_pf_to_dev(pf);
-	pi = pf->hw.port_info;
+
+	devlink_port = &pf->devlink_port;
+
+	vsi = ice_get_main_vsi(pf);
+	if (!vsi)
+		return -EIO;
 
 	attrs.flavour = DEVLINK_PORT_FLAVOUR_PHYSICAL;
-	attrs.phys.port_number = pi->lport;
-	devlink_port_attrs_set(&vsi->devlink_port, &attrs);
-	err = devlink_port_register(devlink, &vsi->devlink_port, vsi->idx);
+	attrs.phys.port_number = pf->hw.bus.func;
+	devlink_port_attrs_set(devlink_port, &attrs);
+	devlink = priv_to_devlink(pf);
+
+	err = devlink_port_register(devlink, devlink_port, vsi->idx);
 	if (err) {
-		dev_err(dev, "devlink_port_register failed: %d\n", err);
+		dev_err(dev, "Failed to create devlink port for PF %d, error %d\n",
+			pf->hw.pf_id, err);
 		return err;
 	}
 
-	vsi->devlink_port_registered = true;
+	return 0;
+}
+
+/**
+ * ice_devlink_destroy_pf_port - Destroy the devlink_port for this PF
+ * @pf: the PF to cleanup
+ *
+ * Unregisters the devlink_port structure associated with this PF.
+ */
+void ice_devlink_destroy_pf_port(struct ice_pf *pf)
+{
+	struct devlink_port *devlink_port;
+
+	devlink_port = &pf->devlink_port;
+
+	devlink_port_type_clear(devlink_port);
+	devlink_port_unregister(devlink_port);
+}
+
+/**
+ * ice_devlink_create_vf_port - Create a devlink port for this VF
+ * @vf: the VF to create a port for
+ *
+ * Create and register a devlink_port for this VF.
+ *
+ * Return: zero on success or an error code on failure.
+ */
+int ice_devlink_create_vf_port(struct ice_vf *vf)
+{
+	struct devlink_port_attrs attrs = {};
+	struct devlink_port *devlink_port;
+	struct devlink *devlink;
+	struct ice_vsi *vsi;
+	struct device *dev;
+	struct ice_pf *pf;
+	int err;
+
+	pf = vf->pf;
+	dev = ice_pf_to_dev(pf);
+	vsi = ice_get_vf_vsi(vf);
+	devlink_port = &vf->devlink_port;
+
+	attrs.flavour = DEVLINK_PORT_FLAVOUR_PCI_VF;
+	attrs.pci_vf.pf = pf->hw.bus.func;
+	attrs.pci_vf.vf = vf->vf_id;
+
+	devlink_port_attrs_set(devlink_port, &attrs);
+	devlink = priv_to_devlink(pf);
+
+	err = devlink_port_register(devlink, devlink_port, vsi->idx);
+	if (err) {
+		dev_err(dev, "Failed to create devlink port for VF %d, error %d\n",
+			vf->vf_id, err);
+		return err;
+	}
 
 	return 0;
 }
 
 /**
- * ice_devlink_destroy_port - Destroy the devlink_port for this VSI
- * @vsi: the VSI to cleanup
+ * ice_devlink_destroy_vf_port - Destroy the devlink_port for this VF
+ * @vf: the VF to cleanup
  *
- * Unregisters the devlink_port structure associated with this VSI.
+ * Unregisters the devlink_port structure associated with this VF.
  */
-void ice_devlink_destroy_port(struct ice_vsi *vsi)
+void ice_devlink_destroy_vf_port(struct ice_vf *vf)
 {
-	if (!vsi->devlink_port_registered)
-		return;
+	struct devlink_port *devlink_port;
 
-	devlink_port_type_clear(&vsi->devlink_port);
-	devlink_port_unregister(&vsi->devlink_port);
+	devlink_port = &vf->devlink_port;
 
-	vsi->devlink_port_registered = false;
+	devlink_port_type_clear(devlink_port);
+	devlink_port_unregister(devlink_port);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_devlink.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_devlink.h
@@ -8,8 +8,10 @@
 
 int ice_devlink_register(struct ice_pf *pf);
 void ice_devlink_unregister(struct ice_pf *pf);
-int ice_devlink_create_port(struct ice_vsi *vsi);
-void ice_devlink_destroy_port(struct ice_vsi *vsi);
+int ice_devlink_create_pf_port(struct ice_pf *pf);
+void ice_devlink_destroy_pf_port(struct ice_pf *pf);
+int ice_devlink_create_vf_port(struct ice_vf *vf);
+void ice_devlink_destroy_vf_port(struct ice_vf *vf);
 
 void ice_devlink_init_regions(struct ice_pf *pf);
 void ice_devlink_destroy_regions(struct ice_pf *pf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_ethtool.c
@@ -651,7 +651,8 @@
 		rx_desc = ICE_RX_DESC(rx_ring, i);
 
 		if (!(rx_desc->wb.status_error0 &
-		    cpu_to_le16(ICE_TX_DESC_CMD_EOP | ICE_TX_DESC_CMD_RS)))
+		    (cpu_to_le16(BIT(ICE_RX_FLEX_DESC_STATUS0_DD_S)) |
+		     cpu_to_le16(BIT(ICE_RX_FLEX_DESC_STATUS0_EOF_S)))))
 			continue;
 
 		rx_buf = &rx_ring->rx_buf[i];
@@ -2151,6 +2152,42 @@
 }
 
 /**
+ * ice_set_phy_type_from_speed - set phy_types based on speeds
+ * and advertised modes
+ * @ks: ethtool link ksettings struct
+ * @phy_type_low: pointer to the lower part of phy_type
+ * @phy_type_high: pointer to the higher part of phy_type
+ * @adv_link_speed: targeted link speeds bitmap
+ */
+static void
+ice_set_phy_type_from_speed(const struct ethtool_link_ksettings *ks,
+			    u64 *phy_type_low, u64 *phy_type_high,
+			    u16 adv_link_speed)
+{
+	/* Handle 1000M speed in a special way because ice_update_phy_type
+	 * enables all link modes, but having mixed copper and optical
+	 * standards is not supported.
+	 */
+	adv_link_speed &= ~ICE_AQ_LINK_SPEED_1000MB;
+
+	if (ethtool_link_ksettings_test_link_mode(ks, advertising,
+						  1000baseT_Full))
+		*phy_type_low |= ICE_PHY_TYPE_LOW_1000BASE_T |
+				 ICE_PHY_TYPE_LOW_1G_SGMII;
+
+	if (ethtool_link_ksettings_test_link_mode(ks, advertising,
+						  1000baseKX_Full))
+		*phy_type_low |= ICE_PHY_TYPE_LOW_1000BASE_KX;
+
+	if (ethtool_link_ksettings_test_link_mode(ks, advertising,
+						  1000baseX_Full))
+		*phy_type_low |= ICE_PHY_TYPE_LOW_1000BASE_SX |
+				 ICE_PHY_TYPE_LOW_1000BASE_LX;
+
+	ice_update_phy_type(phy_type_low, phy_type_high, adv_link_speed);
+}
+
+/**
  * ice_set_link_ksettings - Set Speed and Duplex
  * @netdev: network interface device structure
  * @ks: ethtool ksettings
@@ -2275,7 +2312,7 @@
 		goto done;
 	}
 
-	curr_link_speed = pi->phy.link_info.link_speed;
+	curr_link_speed = pi->phy.curr_user_speed_req;
 	adv_link_speed = ice_ksettings_find_adv_link_speed(ks);
 
 	/* If speed didn't get set, set it to what it currently is.
@@ -2286,7 +2323,8 @@
 		adv_link_speed = curr_link_speed;
 
 	/* Convert the advertise link speeds to their corresponded PHY_TYPE */
-	ice_update_phy_type(&phy_type_low, &phy_type_high, adv_link_speed);
+	ice_set_phy_type_from_speed(ks, &phy_type_low, &phy_type_high,
+				    adv_link_speed);
 
 	if (!autoneg_changed && adv_link_speed == curr_link_speed) {
 		netdev_info(netdev, "Nothing changed, exiting without setting anything.\n");
@@ -2750,6 +2788,7 @@
 		tx_rings[i].count = new_tx_cnt;
 		tx_rings[i].desc = NULL;
 		tx_rings[i].tx_buf = NULL;
+		tx_rings[i].tx_tstamps = &pf->ptp.port.tx;
 		err = ice_setup_tx_ring(&tx_rings[i]);
 		if (err) {
 			while (i--)
@@ -3354,7 +3393,8 @@
 	struct ice_vsi *vsi = np->vsi;
 	struct ice_pf *pf = vsi->back;
 	int new_rx = 0, new_tx = 0;
-	u32 curr_combined;
+	bool locked = false;
+	int ret = 0;
 
 	/* do not support changing channels in Safe Mode */
 	if (ice_is_safe_mode(pf)) {
@@ -3370,22 +3410,8 @@
 		return -EOPNOTSUPP;
 	}
 
-	curr_combined = ice_get_combined_cnt(vsi);
-
-	/* these checks are for cases where user didn't specify a particular
-	 * value on cmd line but we get non-zero value anyway via
-	 * get_channels(); look at ethtool.c in ethtool repository (the user
-	 * space part), particularly, do_schannels() routine
-	 */
-	if (ch->rx_count == vsi->num_rxq - curr_combined)
-		ch->rx_count = 0;
-	if (ch->tx_count == vsi->num_txq - curr_combined)
-		ch->tx_count = 0;
-	if (ch->combined_count == curr_combined)
-		ch->combined_count = 0;
-
-	if (!(ch->combined_count || (ch->rx_count && ch->tx_count))) {
-		netdev_err(dev, "Please specify at least 1 Rx and 1 Tx channel\n");
+	if (ch->rx_count && ch->tx_count) {
+		netdev_err(dev, "Dedicated RX or TX channels cannot be used simultaneously\n");
 		return -EINVAL;
 	}
 
@@ -3403,15 +3429,33 @@
 		return -EINVAL;
 	}
 
-	ice_vsi_recfg_qs(vsi, new_rx, new_tx);
+	if (pf->adev) {
+		mutex_lock(&pf->adev_mutex);
+		device_lock(&pf->adev->dev);
+		locked = true;
+		if (pf->adev->dev.driver) {
+			netdev_err(dev, "Cannot change channels when RDMA is active\n");
+			ret = -EBUSY;
+			goto adev_unlock;
+		}
+	}
 
-	if (!netif_is_rxfh_configured(dev))
-		return ice_vsi_set_dflt_rss_lut(vsi, new_rx);
+	ice_vsi_recfg_qs(vsi, new_rx, new_tx, locked);
+
+	if (!netif_is_rxfh_configured(dev)) {
+		ret = ice_vsi_set_dflt_rss_lut(vsi, new_rx);
+		goto adev_unlock;
+	}
 
 	/* Update rss_size due to change in Rx queues */
 	vsi->rss_size = ice_get_valid_rss_size(&pf->hw, new_rx);
 
-	return 0;
+adev_unlock:
+	if (locked) {
+		device_unlock(&pf->adev->dev);
+		mutex_unlock(&pf->adev_mutex);
+	}
+	return ret;
 }
 
 /**
@@ -3466,15 +3510,9 @@
 	return 0;
 }
 
-enum ice_container_type {
-	ICE_RX_CONTAINER,
-	ICE_TX_CONTAINER,
-};
-
 /**
  * ice_get_rc_coalesce - get ITR values for specific ring container
  * @ec: ethtool structure to fill with driver's coalesce settings
- * @c_type: container type, Rx or Tx
  * @rc: ring container that the ITR values will come from
  *
  * Query the device for ice_ring_container specific ITR values. This is
@@ -3484,13 +3522,12 @@
  * Returns 0 on success, negative otherwise.
  */
 static int
-ice_get_rc_coalesce(struct ethtool_coalesce *ec, enum ice_container_type c_type,
-		    struct ice_ring_container *rc)
+ice_get_rc_coalesce(struct ethtool_coalesce *ec, struct ice_ring_container *rc)
 {
 	if (!rc->ring)
 		return -EINVAL;
 
-	switch (c_type) {
+	switch (rc->type) {
 	case ICE_RX_CONTAINER:
 		ec->use_adaptive_rx_coalesce = ITR_IS_DYNAMIC(rc);
 		ec->rx_coalesce_usecs = rc->itr_setting;
@@ -3501,7 +3538,7 @@
 		ec->tx_coalesce_usecs = rc->itr_setting;
 		break;
 	default:
-		dev_dbg(ice_pf_to_dev(rc->ring->vsi->back), "Invalid c_type %d\n", c_type);
+		dev_dbg(ice_pf_to_dev(rc->ring->vsi->back), "Invalid c_type %d\n", rc->type);
 		return -EINVAL;
 	}
 
@@ -3522,18 +3559,18 @@
 ice_get_q_coalesce(struct ice_vsi *vsi, struct ethtool_coalesce *ec, int q_num)
 {
 	if (q_num < vsi->num_rxq && q_num < vsi->num_txq) {
-		if (ice_get_rc_coalesce(ec, ICE_RX_CONTAINER,
+		if (ice_get_rc_coalesce(ec,
 					&vsi->rx_rings[q_num]->q_vector->rx))
 			return -EINVAL;
-		if (ice_get_rc_coalesce(ec, ICE_TX_CONTAINER,
+		if (ice_get_rc_coalesce(ec,
 					&vsi->tx_rings[q_num]->q_vector->tx))
 			return -EINVAL;
 	} else if (q_num < vsi->num_rxq) {
-		if (ice_get_rc_coalesce(ec, ICE_RX_CONTAINER,
+		if (ice_get_rc_coalesce(ec,
 					&vsi->rx_rings[q_num]->q_vector->rx))
 			return -EINVAL;
 	} else if (q_num < vsi->num_txq) {
-		if (ice_get_rc_coalesce(ec, ICE_TX_CONTAINER,
+		if (ice_get_rc_coalesce(ec,
 					&vsi->tx_rings[q_num]->q_vector->tx))
 			return -EINVAL;
 	} else {
@@ -3585,7 +3622,6 @@
 
 /**
  * ice_set_rc_coalesce - set ITR values for specific ring container
- * @c_type: container type, Rx or Tx
  * @ec: ethtool structure from user to update ITR settings
  * @rc: ring container that the ITR values will come from
  * @vsi: VSI associated to the ring container
@@ -3597,10 +3633,10 @@
  * Returns 0 on success, negative otherwise.
  */
 static int
-ice_set_rc_coalesce(enum ice_container_type c_type, struct ethtool_coalesce *ec,
+ice_set_rc_coalesce(struct ethtool_coalesce *ec,
 		    struct ice_ring_container *rc, struct ice_vsi *vsi)
 {
-	const char *c_type_str = (c_type == ICE_RX_CONTAINER) ? "rx" : "tx";
+	const char *c_type_str = (rc->type == ICE_RX_CONTAINER) ? "rx" : "tx";
 	u32 use_adaptive_coalesce, coalesce_usecs;
 	struct ice_pf *pf = vsi->back;
 	u16 itr_setting;
@@ -3608,7 +3644,7 @@
 	if (!rc->ring)
 		return -EINVAL;
 
-	switch (c_type) {
+	switch (rc->type) {
 	case ICE_RX_CONTAINER:
 		if (ec->rx_coalesce_usecs_high > ICE_MAX_INTRL ||
 		    (ec->rx_coalesce_usecs_high &&
@@ -3641,7 +3677,7 @@
 		break;
 	default:
 		dev_dbg(ice_pf_to_dev(pf), "Invalid container type %d\n",
-			c_type);
+			rc->type);
 		return -EINVAL;
 	}
 
@@ -3690,22 +3726,22 @@
 ice_set_q_coalesce(struct ice_vsi *vsi, struct ethtool_coalesce *ec, int q_num)
 {
 	if (q_num < vsi->num_rxq && q_num < vsi->num_txq) {
-		if (ice_set_rc_coalesce(ICE_RX_CONTAINER, ec,
+		if (ice_set_rc_coalesce(ec,
 					&vsi->rx_rings[q_num]->q_vector->rx,
 					vsi))
 			return -EINVAL;
 
-		if (ice_set_rc_coalesce(ICE_TX_CONTAINER, ec,
+		if (ice_set_rc_coalesce(ec,
 					&vsi->tx_rings[q_num]->q_vector->tx,
 					vsi))
 			return -EINVAL;
 	} else if (q_num < vsi->num_rxq) {
-		if (ice_set_rc_coalesce(ICE_RX_CONTAINER, ec,
+		if (ice_set_rc_coalesce(ec,
 					&vsi->rx_rings[q_num]->q_vector->rx,
 					vsi))
 			return -EINVAL;
 	} else if (q_num < vsi->num_txq) {
-		if (ice_set_rc_coalesce(ICE_TX_CONTAINER, ec,
+		if (ice_set_rc_coalesce(ec,
 					&vsi->tx_rings[q_num]->q_vector->tx,
 					vsi))
 			return -EINVAL;
@@ -3947,6 +3983,8 @@
 		 * SFP modules only ever use page 0.
 		 */
 		if (page == 0 || !(data[0x2] & 0x4)) {
+			u32 copy_len;
+
 			/* If i2c bus is busy due to slow page change or
 			 * link management access, call can fail. This is normal.
 			 * So we retry this a few times.
@@ -3970,8 +4008,8 @@
 			}
 
 			/* Make sure we have enough room for the new block */
-			if ((i + SFF_READ_BLOCK_SIZE) < ee->len)
-				memcpy(data + i, value, SFF_READ_BLOCK_SIZE);
+			copy_len = min_t(u32, SFF_READ_BLOCK_SIZE, ee->len - i);
+			memcpy(data + i, value, copy_len);
 		}
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_ethtool_fdir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_ethtool_fdir.c
@@ -456,7 +456,7 @@
  *
  * Returns the number of available flow director filters to this VSI
  */
-static int ice_fdir_num_avail_fltr(struct ice_hw *hw, struct ice_vsi *vsi)
+int ice_fdir_num_avail_fltr(struct ice_hw *hw, struct ice_vsi *vsi)
 {
 	u16 vsi_num = ice_get_hw_vsi_num(hw, vsi->idx);
 	u16 num_guar;
@@ -1135,16 +1135,21 @@
 				     ICE_FLOW_FLD_OFF_INVAL);
 	}
 
-	/* add filter for outer headers */
 	fltr_idx = ice_ethtool_flow_to_fltr(fsp->flow_type & ~FLOW_EXT);
+
+	assign_bit(fltr_idx, hw->fdir_perfect_fltr, perfect_filter);
+
+	/* add filter for outer headers */
 	ret = ice_fdir_set_hw_fltr_rule(pf, seg, fltr_idx,
 					ICE_FD_HW_SEG_NON_TUN);
-	if (ret == -EEXIST)
-		/* Rule already exists, free memory and continue */
-		devm_kfree(dev, seg);
-	else if (ret)
+	if (ret == -EEXIST) {
+		/* Rule already exists, free memory and count as success */
+		ret = 0;
+		goto err_exit;
+	} else if (ret) {
 		/* could not write filter, free memory */
 		goto err_exit;
+	}
 
 	/* make tunneled filter HW entries if possible */
 	memcpy(&tun_seg[1], seg, sizeof(*seg));
@@ -1159,18 +1164,13 @@
 		devm_kfree(dev, tun_seg);
 	}
 
-	if (perfect_filter)
-		set_bit(fltr_idx, hw->fdir_perfect_fltr);
-	else
-		clear_bit(fltr_idx, hw->fdir_perfect_fltr);
-
 	return ret;
 
 err_exit:
 	devm_kfree(dev, tun_seg);
 	devm_kfree(dev, seg);
 
-	return -EOPNOTSUPP;
+	return ret;
 }
 
 /**
@@ -1684,7 +1684,9 @@
 	input->comp_report = ICE_FXD_FLTR_QW0_COMP_REPORT_SW_FAIL;
 
 	/* input struct is added to the HW filter list */
-	ice_fdir_update_list_entry(pf, input, fsp->location);
+	ret = ice_fdir_update_list_entry(pf, input, fsp->location);
+	if (ret)
+		goto release_lock;
 
 	ret = ice_fdir_write_all_fltr(pf, input, true);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_fdir.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_fdir.h
@@ -201,6 +201,8 @@
 	const u8 *tun_pkt;
 };
 
+struct ice_vsi;
+
 enum ice_status ice_alloc_fd_res_cntr(struct ice_hw *hw, u16 *cntr_id);
 enum ice_status ice_free_fd_res_cntr(struct ice_hw *hw, u16 cntr_id);
 enum ice_status
@@ -214,6 +216,7 @@
 ice_fdir_get_gen_prgm_pkt(struct ice_hw *hw, struct ice_fdir_fltr *input,
 			  u8 *pkt, bool frag, bool tun);
 int ice_get_fdir_cnt_all(struct ice_hw *hw);
+int ice_fdir_num_avail_fltr(struct ice_hw *hw, struct ice_vsi *vsi);
 bool ice_fdir_is_dup_fltr(struct ice_hw *hw, struct ice_fdir_fltr *input);
 bool ice_fdir_has_frag(enum ice_fltr_ptype flow);
 struct ice_fdir_fltr *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_fltr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_fltr.c
@@ -128,7 +128,7 @@
  * @mac: MAC address to add
  * @action: filter action
  */
-int
+enum ice_status
 ice_fltr_add_mac_to_list(struct ice_vsi *vsi, struct list_head *list,
 			 const u8 *mac, enum ice_sw_fwd_act_type action)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_idc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_idc.c
@@ -34,14 +34,20 @@
 {
 	struct iidc_auxiliary_drv *iadrv;
 
-	if (!pf->adev)
+	if (WARN_ON_ONCE(!in_task()))
 		return;
 
+	mutex_lock(&pf->adev_mutex);
+	if (!pf->adev)
+		goto finish;
+
 	device_lock(&pf->adev->dev);
 	iadrv = ice_get_auxiliary_drv(pf);
 	if (iadrv && iadrv->event_handler)
 		iadrv->event_handler(pf, event);
 	device_unlock(&pf->adev->dev);
+finish:
+	mutex_unlock(&pf->adev_mutex);
 }
 
 /**
@@ -282,7 +288,6 @@
 		return -ENOMEM;
 
 	adev = &iadev->adev;
-	pf->adev = adev;
 	iadev->pf = pf;
 
 	adev->id = pf->aux_idx;
@@ -292,18 +297,20 @@
 
 	ret = auxiliary_device_init(adev);
 	if (ret) {
-		pf->adev = NULL;
 		kfree(iadev);
 		return ret;
 	}
 
 	ret = auxiliary_device_add(adev);
 	if (ret) {
-		pf->adev = NULL;
 		auxiliary_device_uninit(adev);
 		return ret;
 	}
 
+	mutex_lock(&pf->adev_mutex);
+	pf->adev = adev;
+	mutex_unlock(&pf->adev_mutex);
+
 	return 0;
 }
 
@@ -312,12 +319,17 @@
  */
 void ice_unplug_aux_dev(struct ice_pf *pf)
 {
-	if (!pf->adev)
-		return;
+	struct auxiliary_device *adev;
 
-	auxiliary_device_delete(pf->adev);
-	auxiliary_device_uninit(pf->adev);
+	mutex_lock(&pf->adev_mutex);
+	adev = pf->adev;
 	pf->adev = NULL;
+	mutex_unlock(&pf->adev_mutex);
+
+	if (adev) {
+		auxiliary_device_delete(adev);
+		auxiliary_device_uninit(adev);
+	}
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_lag.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_lag.c
@@ -4,6 +4,7 @@
 /* Link Aggregation code */
 
 #include "ice.h"
+#include "ice_lib.h"
 #include "ice_lag.h"
 
 /**
@@ -204,11 +205,7 @@
 		lag->upper_netdev = NULL;
 	}
 
-	if (lag->peer_netdev) {
-		dev_put(lag->peer_netdev);
-		lag->peer_netdev = NULL;
-	}
-
+	lag->peer_netdev = NULL;
 	ice_set_sriov_cap(pf);
 	ice_set_rdma_cap(pf);
 	lag->bonded = false;
@@ -216,6 +213,52 @@
 }
 
 /**
+ * ice_lag_unregister - handle netdev unregister events
+ * @lag: LAG info struct
+ * @netdev: netdev reporting the event
+ */
+static void ice_lag_unregister(struct ice_lag *lag, struct net_device *netdev)
+{
+	struct ice_pf *pf = lag->pf;
+
+	/* check to see if this event is for this netdev
+	 * check that we are in an aggregate
+	 */
+	if (netdev != lag->netdev || !lag->bonded)
+		return;
+
+	if (lag->upper_netdev) {
+		dev_put(lag->upper_netdev);
+		lag->upper_netdev = NULL;
+		ice_set_sriov_cap(pf);
+		ice_set_rdma_cap(pf);
+	}
+	/* perform some cleanup in case we come back */
+	lag->bonded = false;
+	lag->role = ICE_LAG_NONE;
+}
+
+/**
+ * ice_lag_init_feature_support_flag - Check for NVM support for LAG
+ * @pf: PF struct
+ */
+static void ice_lag_init_feature_support_flag(struct ice_pf *pf)
+{
+	struct ice_hw_common_caps *caps;
+
+	caps = &pf->hw.dev_caps.common_cap;
+	if (caps->roce_lag)
+		ice_set_feature_support(pf, ICE_F_ROCE_LAG);
+	else
+		clear_bit(ICE_F_ROCE_LAG, pf->features);
+
+	if (caps->sriov_lag)
+		ice_set_feature_support(pf, ICE_F_SRIOV_LAG);
+	else
+		clear_bit(ICE_F_SRIOV_LAG, pf->features);
+}
+
+/**
  * ice_lag_changeupper_event - handle LAG changeupper event
  * @lag: LAG info struct
  * @ptr: opaque pointer data
@@ -255,26 +298,6 @@
 }
 
 /**
- * ice_lag_changelower_event - handle LAG changelower event
- * @lag: LAG info struct
- * @ptr: opaque data pointer
- *
- * ptr to be cast to netdev_notifier_changelowerstate_info
- */
-static void ice_lag_changelower_event(struct ice_lag *lag, void *ptr)
-{
-	struct net_device *netdev = netdev_notifier_info_to_dev(ptr);
-
-	if (netdev != lag->netdev)
-		return;
-
-	netdev_dbg(netdev, "bonding info\n");
-
-	if (!netif_is_lag_port(netdev))
-		netdev_dbg(netdev, "CHANGELOWER rcvd, but netdev not in LAG. Bail\n");
-}
-
-/**
  * ice_lag_event_handler - handle LAG events from netdev
  * @notif_blk: notifier block registered by this netdev
  * @event: event type
@@ -300,14 +323,11 @@
 	case NETDEV_CHANGEUPPER:
 		ice_lag_changeupper_event(lag, ptr);
 		break;
-	case NETDEV_CHANGELOWERSTATE:
-		ice_lag_changelower_event(lag, ptr);
-		break;
 	case NETDEV_BONDING_INFO:
 		ice_lag_info_event(lag, ptr);
 		break;
 	case NETDEV_UNREGISTER:
-		ice_lag_unlink(lag, ptr);
+		ice_lag_unregister(lag, netdev);
 		break;
 	default:
 		break;
@@ -369,6 +389,10 @@
 	struct ice_vsi *vsi;
 	int err;
 
+	ice_lag_init_feature_support_flag(pf);
+	if (!ice_is_feature_supported(pf, ICE_F_SRIOV_LAG))
+		return 0;
+
 	pf->lag = kzalloc(sizeof(*lag), GFP_KERNEL);
 	if (!pf->lag)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h
@@ -528,6 +528,7 @@
 			(0x3FFFFULL << ICE_TXD_CTX_QW1_TSO_LEN_S)
 
 #define ICE_TXD_CTX_QW1_MSS_S	50
+#define ICE_TXD_CTX_MIN_MSS	64
 
 enum ice_tx_ctx_desc_cmd_bits {
 	ICE_TX_CTX_DESC_TSO		= 0x01,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_lib.c
@@ -83,8 +83,13 @@
 	if (!vsi->rx_rings)
 		goto err_rings;
 
-	/* XDP will have vsi->alloc_txq Tx queues as well, so double the size */
-	vsi->txq_map = devm_kcalloc(dev, (2 * vsi->alloc_txq),
+	/* txq_map needs to have enough space to track both Tx (stack) rings
+	 * and XDP rings; at this point vsi->num_xdp_txq might not be set,
+	 * so use num_possible_cpus() as we want to always provide XDP ring
+	 * per CPU, regardless of queue count settings from user that might
+	 * have come from ethtool's set_channels() callback;
+	 */
+	vsi->txq_map = devm_kcalloc(dev, (vsi->alloc_txq + num_possible_cpus()),
 				    sizeof(*vsi->txq_map), GFP_KERNEL);
 
 	if (!vsi->txq_map)
@@ -949,8 +954,7 @@
 
 	ctxt->info.q_opt_rss = ((lut_type << ICE_AQ_VSI_Q_OPT_RSS_LUT_S) &
 				ICE_AQ_VSI_Q_OPT_RSS_LUT_M) |
-				((hash_type << ICE_AQ_VSI_Q_OPT_RSS_HASH_S) &
-				 ICE_AQ_VSI_Q_OPT_RSS_HASH_M);
+				(hash_type & ICE_AQ_VSI_Q_OPT_RSS_HASH_M);
 }
 
 /**
@@ -1301,6 +1305,7 @@
 		ring->tx_tstamps = &pf->ptp.port.tx;
 		ring->dev = dev;
 		ring->count = vsi->num_tx_desc;
+		ring->txq_teid = ICE_INVAL_TEID;
 		WRITE_ONCE(vsi->tx_rings[i], ring);
 	}
 
@@ -1516,6 +1521,12 @@
 	if (status)
 		dev_dbg(dev, "ice_add_rss_cfg failed for sctp6 flow, vsi = %d, error = %s\n",
 			vsi_num, ice_stat_str(status));
+
+	status = ice_add_rss_cfg(hw, vsi_handle, ICE_FLOW_HASH_ESP_SPI,
+				 ICE_FLOW_SEG_HDR_ESP);
+	if (status)
+		dev_dbg(dev, "ice_add_rss_cfg failed for esp/spi flow, vsi = %d, error = %d\n",
+			vsi_num, status);
 }
 
 /**
@@ -2740,8 +2751,7 @@
  */
 void ice_dis_vsi(struct ice_vsi *vsi, bool locked)
 {
-	if (test_bit(ICE_VSI_DOWN, vsi->state))
-		return;
+	bool already_down = test_bit(ICE_VSI_DOWN, vsi->state);
 
 	set_bit(ICE_VSI_NEEDS_RESTART, vsi->state);
 
@@ -2749,15 +2759,16 @@
 		if (netif_running(vsi->netdev)) {
 			if (!locked)
 				rtnl_lock();
-
-			ice_vsi_close(vsi);
+			already_down = test_bit(ICE_VSI_DOWN, vsi->state);
+			if (!already_down)
+				ice_vsi_close(vsi);
 
 			if (!locked)
 				rtnl_unlock();
-		} else {
+		} else if (!already_down) {
 			ice_vsi_close(vsi);
 		}
-	} else if (vsi->type == ICE_VSI_CTRL) {
+	} else if (vsi->type == ICE_VSI_CTRL && !already_down) {
 		ice_vsi_close(vsi);
 	}
 }
@@ -2860,7 +2871,8 @@
 		clear_bit(ICE_VSI_NETDEV_REGISTERED, vsi->state);
 	}
 
-	ice_devlink_destroy_port(vsi);
+	if (vsi->type == ICE_VSI_PF)
+		ice_devlink_destroy_pf_port(pf);
 
 	if (test_bit(ICE_FLAG_RSS_ENA, pf->flags))
 		ice_rss_clean(vsi);
@@ -2911,6 +2923,8 @@
 		}
 	}
 
+	if (ice_is_vsi_dflt_vsi(pf->first_sw, vsi))
+		ice_clear_dflt_vsi(pf->first_sw);
 	ice_fltr_remove_all(vsi);
 	ice_rm_vsi_lan_cfg(vsi->port_info, vsi->idx);
 	err = ice_rm_vsi_rdma_cfg(vsi->port_info, vsi->idx);
@@ -2965,8 +2979,8 @@
 	ice_for_each_q_vector(vsi, i) {
 		struct ice_q_vector *q_vector = vsi->q_vectors[i];
 
-		coalesce[i].itr_tx = q_vector->tx.itr_setting;
-		coalesce[i].itr_rx = q_vector->rx.itr_setting;
+		coalesce[i].itr_tx = q_vector->tx.itr_settings;
+		coalesce[i].itr_rx = q_vector->rx.itr_settings;
 		coalesce[i].intrl = q_vector->intrl;
 
 		if (i < vsi->num_txq)
@@ -3022,21 +3036,21 @@
 		 */
 		if (i < vsi->alloc_rxq && coalesce[i].rx_valid) {
 			rc = &vsi->q_vectors[i]->rx;
-			rc->itr_setting = coalesce[i].itr_rx;
+			rc->itr_settings = coalesce[i].itr_rx;
 			ice_write_itr(rc, rc->itr_setting);
 		} else if (i < vsi->alloc_rxq) {
 			rc = &vsi->q_vectors[i]->rx;
-			rc->itr_setting = coalesce[0].itr_rx;
+			rc->itr_settings = coalesce[0].itr_rx;
 			ice_write_itr(rc, rc->itr_setting);
 		}
 
 		if (i < vsi->alloc_txq && coalesce[i].tx_valid) {
 			rc = &vsi->q_vectors[i]->tx;
-			rc->itr_setting = coalesce[i].itr_tx;
+			rc->itr_settings = coalesce[i].itr_tx;
 			ice_write_itr(rc, rc->itr_setting);
 		} else if (i < vsi->alloc_txq) {
 			rc = &vsi->q_vectors[i]->tx;
-			rc->itr_setting = coalesce[0].itr_tx;
+			rc->itr_settings = coalesce[0].itr_tx;
 			ice_write_itr(rc, rc->itr_setting);
 		}
 
@@ -3050,12 +3064,12 @@
 	for (; i < vsi->num_q_vectors; i++) {
 		/* transmit */
 		rc = &vsi->q_vectors[i]->tx;
-		rc->itr_setting = coalesce[0].itr_tx;
+		rc->itr_settings = coalesce[0].itr_tx;
 		ice_write_itr(rc, rc->itr_setting);
 
 		/* receive */
 		rc = &vsi->q_vectors[i]->rx;
-		rc->itr_setting = coalesce[0].itr_rx;
+		rc->itr_settings = coalesce[0].itr_rx;
 		ice_write_itr(rc, rc->itr_setting);
 
 		vsi->q_vectors[i]->intrl = coalesce[0].intrl;
@@ -3582,3 +3596,50 @@
 
 	return 0;
 }
+
+/**
+ * ice_is_feature_supported
+ * @pf: pointer to the struct ice_pf instance
+ * @f: feature enum to be checked
+ *
+ * returns true if feature is supported, false otherwise
+ */
+bool ice_is_feature_supported(struct ice_pf *pf, enum ice_feature f)
+{
+	if (f < 0 || f >= ICE_F_MAX)
+		return false;
+
+	return test_bit(f, pf->features);
+}
+
+/**
+ * ice_set_feature_support
+ * @pf: pointer to the struct ice_pf instance
+ * @f: feature enum to set
+ */
+void ice_set_feature_support(struct ice_pf *pf, enum ice_feature f)
+{
+	if (f < 0 || f >= ICE_F_MAX)
+		return;
+
+	set_bit(f, pf->features);
+}
+
+/**
+ * ice_init_feature_support
+ * @pf: pointer to the struct ice_pf instance
+ *
+ * called during init to setup supported feature
+ */
+void ice_init_feature_support(struct ice_pf *pf)
+{
+	switch (pf->hw.device_id) {
+	case ICE_DEV_ID_E810C_BACKPLANE:
+	case ICE_DEV_ID_E810C_QSFP:
+	case ICE_DEV_ID_E810C_SFP:
+		ice_set_feature_support(pf, ICE_F_DSCP);
+		break;
+	default:
+		break;
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_lib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_lib.h
@@ -116,4 +116,7 @@
 int ice_set_dflt_vsi(struct ice_sw *sw, struct ice_vsi *vsi);
 
 int ice_clear_dflt_vsi(struct ice_sw *sw);
+bool ice_is_feature_supported(struct ice_pf *pf, enum ice_feature f);
+void ice_set_feature_support(struct ice_pf *pf, enum ice_feature f);
+void ice_init_feature_support(struct ice_pf *pf);
 #endif /* !_ICE_LIB_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_main.c
@@ -6,6 +6,7 @@
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
 #include <generated/utsrelease.h>
+#include <linux/crash_dump.h>
 #include "ice.h"
 #include "ice_base.h"
 #include "ice_lib.h"
@@ -54,7 +55,8 @@
 
 bool netif_is_ice(struct net_device *dev)
 {
-	return dev && (dev->netdev_ops == &ice_netdev_ops);
+	return dev && (dev->netdev_ops == &ice_netdev_ops ||
+		       dev->netdev_ops == &ice_netdev_safe_mode_ops);
 }
 
 /**
@@ -1177,6 +1179,7 @@
 static void ice_aq_check_events(struct ice_pf *pf, u16 opcode,
 				struct ice_rq_event_info *event)
 {
+	struct ice_rq_event_info *task_ev;
 	struct ice_aq_task *task;
 	bool found = false;
 
@@ -1185,15 +1188,15 @@
 		if (task->state || task->opcode != opcode)
 			continue;
 
-		memcpy(&task->event->desc, &event->desc, sizeof(event->desc));
-		task->event->msg_len = event->msg_len;
+		task_ev = task->event;
+		memcpy(&task_ev->desc, &event->desc, sizeof(event->desc));
+		task_ev->msg_len = event->msg_len;
 
 		/* Only copy the data buffer if a destination was set */
-		if (task->event->msg_buf &&
-		    task->event->buf_len > event->buf_len) {
-			memcpy(task->event->msg_buf, event->msg_buf,
+		if (task_ev->msg_buf && task_ev->buf_len >= event->buf_len) {
+			memcpy(task_ev->msg_buf, event->msg_buf,
 			       event->buf_len);
-			task->event->buf_len = event->buf_len;
+			task_ev->buf_len = event->buf_len;
 		}
 
 		task->state = ICE_AQ_TASK_COMPLETE;
@@ -1679,7 +1682,9 @@
 				 * reset, so print the event prior to reset.
 				 */
 				ice_print_vf_rx_mdd_event(vf);
+				mutex_lock(&pf->vf[i].cfg_lock);
 				ice_reset_vf(&pf->vf[i], false);
+				mutex_unlock(&pf->vf[i].cfg_lock);
 			}
 		}
 	}
@@ -2141,6 +2146,40 @@
 		return;
 	}
 
+	if (test_and_clear_bit(ICE_AUX_ERR_PENDING, pf->state)) {
+		struct iidc_event *event;
+
+		event = kzalloc(sizeof(*event), GFP_KERNEL);
+		if (event) {
+			set_bit(IIDC_EVENT_CRIT_ERR, event->type);
+			/* report the entire OICR value to AUX driver */
+			swap(event->reg, pf->oicr_err_reg);
+			ice_send_event_to_aux(pf, event);
+			kfree(event);
+		}
+	}
+
+	/* unplug aux dev per request, if an unplug request came in
+	 * while processing a plug request, this will handle it
+	 */
+	if (test_and_clear_bit(ICE_FLAG_UNPLUG_AUX_DEV, pf->flags))
+		ice_unplug_aux_dev(pf);
+
+	/* Plug aux device per request */
+	if (test_and_clear_bit(ICE_FLAG_PLUG_AUX_DEV, pf->flags))
+		ice_plug_aux_dev(pf);
+
+	if (test_and_clear_bit(ICE_FLAG_MTU_CHANGED, pf->flags)) {
+		struct iidc_event *event;
+
+		event = kzalloc(sizeof(*event), GFP_KERNEL);
+		if (event) {
+			set_bit(IIDC_EVENT_AFTER_MTU_CHANGE, event->type);
+			ice_send_event_to_aux(pf, event);
+			kfree(event);
+		}
+	}
+
 	ice_clean_adminq_subtask(pf);
 	ice_check_media_subtask(pf);
 	ice_check_for_hang_subtask(pf);
@@ -2216,8 +2255,6 @@
 		return -EBUSY;
 	}
 
-	ice_unplug_aux_dev(pf);
-
 	switch (reset) {
 	case ICE_RESET_PFR:
 		set_bit(ICE_PFR_REQ, pf->state);
@@ -2497,7 +2534,18 @@
 			ice_stat_str(status));
 		goto clear_xdp_rings;
 	}
-	ice_vsi_assign_bpf_prog(vsi, prog);
+
+	/* assign the prog only when it's not already present on VSI;
+	 * this flow is a subject of both ethtool -L and ndo_bpf flows;
+	 * VSI rebuild that happens under ethtool -L can expose us to
+	 * the bpf_prog refcount issues as we would be swapping same
+	 * bpf_prog pointers from vsi->xdp_prog and calling bpf_prog_put
+	 * on it as it would be treated as an 'old_prog'; for ndo_bpf
+	 * this is not harmful as dev_xdp_install bumps the refcount
+	 * before calling the op exposed by the driver;
+	 */
+	if (!ice_is_xdp_ena_vsi(vsi))
+		ice_vsi_assign_bpf_prog(vsi, prog);
 
 	return 0;
 clear_xdp_rings:
@@ -2562,8 +2610,10 @@
 
 	for (i = 0; i < vsi->num_xdp_txq; i++)
 		if (vsi->xdp_rings[i]) {
-			if (vsi->xdp_rings[i]->desc)
+			if (vsi->xdp_rings[i]->desc) {
+				synchronize_rcu();
 				ice_free_tx_ring(vsi->xdp_rings[i]);
+			}
 			kfree_rcu(vsi->xdp_rings[i], rcu);
 			vsi->xdp_rings[i] = NULL;
 		}
@@ -2643,6 +2693,11 @@
 		if (xdp_ring_err)
 			NL_SET_ERR_MSG_MOD(extack, "Freeing XDP Tx resources failed");
 	} else {
+		/* safe to call even when prog == vsi->xdp_prog as
+		 * dev_xdp_install in net/core/dev.c incremented prog's
+		 * refcount so corresponding bpf_prog_put won't cause
+		 * underflow
+		 */
 		ice_vsi_assign_bpf_prog(vsi, prog);
 	}
 
@@ -2839,17 +2894,9 @@
 
 #define ICE_AUX_CRIT_ERR (PFINT_OICR_PE_CRITERR_M | PFINT_OICR_HMC_ERR_M | PFINT_OICR_PE_PUSH_M)
 	if (oicr & ICE_AUX_CRIT_ERR) {
-		struct iidc_event *event;
-
+		pf->oicr_err_reg |= oicr;
+		set_bit(ICE_AUX_ERR_PENDING, pf->state);
 		ena_mask &= ~ICE_AUX_CRIT_ERR;
-		event = kzalloc(sizeof(*event), GFP_KERNEL);
-		if (event) {
-			set_bit(IIDC_EVENT_CRIT_ERR, event->type);
-			/* report the entire OICR value to AUX driver */
-			event->reg = oicr;
-			ice_send_event_to_aux(pf, event);
-			kfree(event);
-		}
 	}
 
 	/* Report any remaining unexpected interrupts */
@@ -3139,7 +3186,7 @@
 	if (vsi->type == ICE_VSI_PF) {
 		SET_NETDEV_DEV(netdev, ice_pf_to_dev(vsi->back));
 		ether_addr_copy(mac_addr, vsi->port_info->mac.perm_addr);
-		ether_addr_copy(netdev->dev_addr, mac_addr);
+		eth_hw_addr_set(netdev, mac_addr);
 		ether_addr_copy(netdev->perm_addr, mac_addr);
 	}
 
@@ -3398,6 +3445,7 @@
 static void ice_deinit_pf(struct ice_pf *pf)
 {
 	ice_service_task_stop(pf);
+	mutex_destroy(&pf->adev_mutex);
 	mutex_destroy(&pf->sw_mutex);
 	mutex_destroy(&pf->tc_mutex);
 	mutex_destroy(&pf->avail_q_mutex);
@@ -3478,6 +3526,7 @@
 
 	mutex_init(&pf->sw_mutex);
 	mutex_init(&pf->tc_mutex);
+	mutex_init(&pf->adev_mutex);
 
 	INIT_HLIST_HEAD(&pf->aq_wait_list);
 	spin_lock_init(&pf->aq_wait_lock);
@@ -3498,7 +3547,7 @@
 
 	pf->avail_rxqs = bitmap_zalloc(pf->max_pf_rxqs, GFP_KERNEL);
 	if (!pf->avail_rxqs) {
-		devm_kfree(ice_pf_to_dev(pf), pf->avail_txqs);
+		bitmap_free(pf->avail_txqs);
 		pf->avail_txqs = NULL;
 		return -ENOMEM;
 	}
@@ -3507,80 +3556,131 @@
 }
 
 /**
+ * ice_reduce_msix_usage - Reduce usage of MSI-X vectors
+ * @pf: board private structure
+ * @v_remain: number of remaining MSI-X vectors to be distributed
+ *
+ * Reduce the usage of MSI-X vectors when entire request cannot be fulfilled.
+ * pf->num_lan_msix and pf->num_rdma_msix values are set based on number of
+ * remaining vectors.
+ */
+static void ice_reduce_msix_usage(struct ice_pf *pf, int v_remain)
+{
+	int v_rdma;
+
+	if (!test_bit(ICE_FLAG_RDMA_ENA, pf->flags)) {
+		pf->num_lan_msix = v_remain;
+		return;
+	}
+
+	/* RDMA needs at least 1 interrupt in addition to AEQ MSIX */
+	v_rdma = ICE_RDMA_NUM_AEQ_MSIX + 1;
+
+	if (v_remain < ICE_MIN_LAN_TXRX_MSIX + ICE_MIN_RDMA_MSIX) {
+		dev_warn(ice_pf_to_dev(pf), "Not enough MSI-X vectors to support RDMA.\n");
+		clear_bit(ICE_FLAG_RDMA_ENA, pf->flags);
+
+		pf->num_rdma_msix = 0;
+		pf->num_lan_msix = ICE_MIN_LAN_TXRX_MSIX;
+	} else if ((v_remain < ICE_MIN_LAN_TXRX_MSIX + v_rdma) ||
+		   (v_remain - v_rdma < v_rdma)) {
+		/* Support minimum RDMA and give remaining vectors to LAN MSIX */
+		pf->num_rdma_msix = ICE_MIN_RDMA_MSIX;
+		pf->num_lan_msix = v_remain - ICE_MIN_RDMA_MSIX;
+	} else {
+		/* Split remaining MSIX with RDMA after accounting for AEQ MSIX
+		 */
+		pf->num_rdma_msix = (v_remain - ICE_RDMA_NUM_AEQ_MSIX) / 2 +
+				    ICE_RDMA_NUM_AEQ_MSIX;
+		pf->num_lan_msix = v_remain - pf->num_rdma_msix;
+	}
+}
+
+/**
  * ice_ena_msix_range - Request a range of MSIX vectors from the OS
  * @pf: board private structure
  *
- * compute the number of MSIX vectors required (v_budget) and request from
- * the OS. Return the number of vectors reserved or negative on failure
+ * Compute the number of MSIX vectors wanted and request from the OS. Adjust
+ * device usage if there are not enough vectors. Return the number of vectors
+ * reserved or negative on failure.
  */
 static int ice_ena_msix_range(struct ice_pf *pf)
 {
-	int num_cpus, v_left, v_actual, v_other, v_budget = 0;
+	int num_cpus, hw_num_msix, v_other, v_wanted, v_actual;
 	struct device *dev = ice_pf_to_dev(pf);
-	int needed, err, i;
+	int err, i;
 
-	v_left = pf->hw.func_caps.common_cap.num_msix_vectors;
+	hw_num_msix = pf->hw.func_caps.common_cap.num_msix_vectors;
 	num_cpus = num_online_cpus();
 
-	/* reserve for LAN miscellaneous handler */
-	needed = ICE_MIN_LAN_OICR_MSIX;
-	if (v_left < needed)
-		goto no_hw_vecs_left_err;
-	v_budget += needed;
-	v_left -= needed;
+	/* LAN miscellaneous handler */
+	v_other = ICE_MIN_LAN_OICR_MSIX;
 
-	/* reserve for flow director */
-	if (test_bit(ICE_FLAG_FD_ENA, pf->flags)) {
-		needed = ICE_FDIR_MSIX;
-		if (v_left < needed)
-			goto no_hw_vecs_left_err;
-		v_budget += needed;
-		v_left -= needed;
-	}
-
-	/* total used for non-traffic vectors */
-	v_other = v_budget;
-
-	/* reserve vectors for LAN traffic */
-	needed = num_cpus;
-	if (v_left < needed)
-		goto no_hw_vecs_left_err;
-	pf->num_lan_msix = needed;
-	v_budget += needed;
-	v_left -= needed;
+	/* Flow Director */
+	if (test_bit(ICE_FLAG_FD_ENA, pf->flags))
+		v_other += ICE_FDIR_MSIX;
 
-	/* reserve vectors for RDMA auxiliary driver */
+	v_wanted = v_other;
+
+	/* LAN traffic */
+	pf->num_lan_msix = num_cpus;
+	v_wanted += pf->num_lan_msix;
+
+	/* RDMA auxiliary driver */
 	if (test_bit(ICE_FLAG_RDMA_ENA, pf->flags)) {
-		needed = num_cpus + ICE_RDMA_NUM_AEQ_MSIX;
-		if (v_left < needed)
-			goto no_hw_vecs_left_err;
-		pf->num_rdma_msix = needed;
-		v_budget += needed;
-		v_left -= needed;
+		pf->num_rdma_msix = num_cpus + ICE_RDMA_NUM_AEQ_MSIX;
+		v_wanted += pf->num_rdma_msix;
 	}
 
-	pf->msix_entries = devm_kcalloc(dev, v_budget,
+	if (v_wanted > hw_num_msix) {
+		int v_remain;
+
+		dev_warn(dev, "not enough device MSI-X vectors. wanted = %d, available = %d\n",
+			 v_wanted, hw_num_msix);
+
+		if (hw_num_msix < ICE_MIN_MSIX) {
+			err = -ERANGE;
+			goto exit_err;
+		}
+
+		v_remain = hw_num_msix - v_other;
+		if (v_remain < ICE_MIN_LAN_TXRX_MSIX) {
+			v_other = ICE_MIN_MSIX - ICE_MIN_LAN_TXRX_MSIX;
+			v_remain = ICE_MIN_LAN_TXRX_MSIX;
+		}
+
+		ice_reduce_msix_usage(pf, v_remain);
+		v_wanted = pf->num_lan_msix + pf->num_rdma_msix + v_other;
+
+		dev_notice(dev, "Reducing request to %d MSI-X vectors for LAN traffic.\n",
+			   pf->num_lan_msix);
+		if (test_bit(ICE_FLAG_RDMA_ENA, pf->flags))
+			dev_notice(dev, "Reducing request to %d MSI-X vectors for RDMA.\n",
+				   pf->num_rdma_msix);
+	}
+
+	pf->msix_entries = devm_kcalloc(dev, v_wanted,
 					sizeof(*pf->msix_entries), GFP_KERNEL);
 	if (!pf->msix_entries) {
 		err = -ENOMEM;
 		goto exit_err;
 	}
 
-	for (i = 0; i < v_budget; i++)
+	for (i = 0; i < v_wanted; i++)
 		pf->msix_entries[i].entry = i;
 
 	/* actually reserve the vectors */
 	v_actual = pci_enable_msix_range(pf->pdev, pf->msix_entries,
-					 ICE_MIN_MSIX, v_budget);
+					 ICE_MIN_MSIX, v_wanted);
 	if (v_actual < 0) {
 		dev_err(dev, "unable to reserve MSI-X vectors\n");
 		err = v_actual;
 		goto msix_err;
 	}
 
-	if (v_actual < v_budget) {
+	if (v_actual < v_wanted) {
 		dev_warn(dev, "not enough OS MSI-X vectors. requested = %d, obtained = %d\n",
-			 v_budget, v_actual);
+			 v_wanted, v_actual);
 
 		if (v_actual < ICE_MIN_MSIX) {
 			/* error if we can't get minimum vectors */
@@ -3589,38 +3689,11 @@
 			goto msix_err;
 		} else {
 			int v_remain = v_actual - v_other;
-			int v_rdma = 0, v_min_rdma = 0;
 
-			if (test_bit(ICE_FLAG_RDMA_ENA, pf->flags)) {
-				/* Need at least 1 interrupt in addition to
-				 * AEQ MSIX
-				 */
-				v_rdma = ICE_RDMA_NUM_AEQ_MSIX + 1;
-				v_min_rdma = ICE_MIN_RDMA_MSIX;
-			}
+			if (v_remain < ICE_MIN_LAN_TXRX_MSIX)
+				v_remain = ICE_MIN_LAN_TXRX_MSIX;
 
-			if (v_actual == ICE_MIN_MSIX ||
-			    v_remain < ICE_MIN_LAN_TXRX_MSIX + v_min_rdma) {
-				dev_warn(dev, "Not enough MSI-X vectors to support RDMA.\n");
-				clear_bit(ICE_FLAG_RDMA_ENA, pf->flags);
-
-				pf->num_rdma_msix = 0;
-				pf->num_lan_msix = ICE_MIN_LAN_TXRX_MSIX;
-			} else if ((v_remain < ICE_MIN_LAN_TXRX_MSIX + v_rdma) ||
-				   (v_remain - v_rdma < v_rdma)) {
-				/* Support minimum RDMA and give remaining
-				 * vectors to LAN MSIX
-				 */
-				pf->num_rdma_msix = v_min_rdma;
-				pf->num_lan_msix = v_remain - v_min_rdma;
-			} else {
-				/* Split remaining MSIX with RDMA after
-				 * accounting for AEQ MSIX
-				 */
-				pf->num_rdma_msix = (v_remain - ICE_RDMA_NUM_AEQ_MSIX) / 2 +
-						    ICE_RDMA_NUM_AEQ_MSIX;
-				pf->num_lan_msix = v_remain - pf->num_rdma_msix;
-			}
+			ice_reduce_msix_usage(pf, v_remain);
 
 			dev_notice(dev, "Enabled %d MSI-X vectors for LAN traffic.\n",
 				   pf->num_lan_msix);
@@ -3635,12 +3708,7 @@
 
 msix_err:
 	devm_kfree(dev, pf->msix_entries);
-	goto exit_err;
 
-no_hw_vecs_left_err:
-	dev_err(dev, "not enough device MSI-X vectors. requested = %d, available = %d\n",
-		needed, v_left);
-	err = -ERANGE;
 exit_err:
 	pf->num_rdma_msix = 0;
 	pf->num_lan_msix = 0;
@@ -3727,12 +3795,13 @@
  * @vsi: VSI being changed
  * @new_rx: new number of Rx queues
  * @new_tx: new number of Tx queues
+ * @locked: is adev device_lock held
  *
  * Only change the number of queues if new_tx, or new_rx is non-0.
  *
  * Returns 0 on success.
  */
-int ice_vsi_recfg_qs(struct ice_vsi *vsi, int new_rx, int new_tx)
+int ice_vsi_recfg_qs(struct ice_vsi *vsi, int new_rx, int new_tx, bool locked)
 {
 	struct ice_pf *pf = vsi->back;
 	int err = 0, timeout = 50;
@@ -3761,7 +3830,7 @@
 
 	ice_vsi_close(vsi);
 	ice_vsi_rebuild(vsi, false);
-	ice_pf_dcb_recfg(pf);
+	ice_pf_dcb_recfg(pf, locked);
 	ice_vsi_open(vsi);
 done:
 	clear_bit(ICE_CFG_BUSY, pf->state);
@@ -4170,11 +4239,11 @@
 	set_bit(ICE_VSI_NETDEV_REGISTERED, vsi->state);
 	netif_carrier_off(vsi->netdev);
 	netif_tx_stop_all_queues(vsi->netdev);
-	err = ice_devlink_create_port(vsi);
+	err = ice_devlink_create_pf_port(pf);
 	if (err)
 		goto err_devlink_create;
 
-	devlink_port_type_eth_set(&vsi->devlink_port, vsi->netdev);
+	devlink_port_type_eth_set(&pf->devlink_port, vsi->netdev);
 
 	return 0;
 err_devlink_create:
@@ -4207,6 +4276,20 @@
 		return -EINVAL;
 	}
 
+	/* when under a kdump kernel initiate a reset before enabling the
+	 * device in order to clear out any pending DMA transactions. These
+	 * transactions can cause some systems to machine check when doing
+	 * the pcim_enable_device() below.
+	 */
+	if (is_kdump_kernel()) {
+		pci_save_state(pdev);
+		pci_clear_master(pdev);
+		err = pcie_flr(pdev);
+		if (err)
+			return err;
+		pci_restore_state(pdev);
+	}
+
 	/* this driver uses devres, see
 	 * Documentation/driver-api/driver-model/devres.rst
 	 */
@@ -4279,6 +4362,8 @@
 		goto err_exit_unroll;
 	}
 
+	ice_init_feature_support(pf);
+
 	ice_request_fw(pf);
 
 	/* if ice_request_fw fails, ICE_FLAG_ADV_FEATURES bit won't be
@@ -4600,9 +4685,6 @@
 	struct ice_pf *pf = pci_get_drvdata(pdev);
 	int i;
 
-	if (!pf)
-		return;
-
 	for (i = 0; i < ICE_MAX_RESET_WAIT; i++) {
 		if (!ice_is_reset_in_progress(pf->state))
 			break;
@@ -5083,7 +5165,7 @@
 	pr_info("%s\n", ice_driver_string);
 	pr_info("%s\n", ice_copyright);
 
-	ice_wq = alloc_workqueue("%s", WQ_MEM_RECLAIM, 0, KBUILD_MODNAME);
+	ice_wq = alloc_workqueue("%s", 0, 0, KBUILD_MODNAME);
 	if (!ice_wq) {
 		pr_err("Failed to create workqueue\n");
 		return -ENOMEM;
@@ -5181,7 +5263,7 @@
 		netdev_err(netdev, "can't set MAC %pM. filter update failed\n",
 			   mac);
 		netif_addr_lock_bh(netdev);
-		ether_addr_copy(netdev->dev_addr, old_mac);
+		eth_hw_addr_set(netdev, old_mac);
 		netif_addr_unlock_bh(netdev);
 		return err;
 	}
@@ -5430,11 +5512,10 @@
 {
 	int err;
 
-	if (vsi->netdev) {
+	if (vsi->netdev && vsi->type == ICE_VSI_PF) {
 		ice_set_rx_mode(vsi->netdev);
 
 		err = ice_vsi_vlan_setup(vsi);
-
 		if (err)
 			return err;
 	}
@@ -5602,13 +5683,19 @@
 
 	if (vsi->port_info &&
 	    (vsi->port_info->phy.link_info.link_info & ICE_AQ_LINK_UP) &&
-	    vsi->netdev) {
+	    vsi->netdev && vsi->type == ICE_VSI_PF) {
 		ice_print_link_msg(vsi, true);
 		netif_tx_start_all_queues(vsi->netdev);
 		netif_carrier_on(vsi->netdev);
 	}
 
-	ice_service_task_schedule(pf);
+	/* Perform an initial read of the statistics registers now to
+	 * set the baseline so counters are ready when interface is up
+	 */
+	ice_update_eth_stats(vsi);
+
+	if (vsi->type == ICE_VSI_PF)
+		ice_service_task_schedule(pf);
 
 	return 0;
 }
@@ -6511,7 +6598,6 @@
 	struct ice_netdev_priv *np = netdev_priv(netdev);
 	struct ice_vsi *vsi = np->vsi;
 	struct ice_pf *pf = vsi->back;
-	struct iidc_event *event;
 	u8 count = 0;
 	int err = 0;
 
@@ -6546,14 +6632,6 @@
 		return -EBUSY;
 	}
 
-	event = kzalloc(sizeof(*event), GFP_KERNEL);
-	if (!event)
-		return -ENOMEM;
-
-	set_bit(IIDC_EVENT_BEFORE_MTU_CHANGE, event->type);
-	ice_send_event_to_aux(pf, event);
-	clear_bit(IIDC_EVENT_BEFORE_MTU_CHANGE, event->type);
-
 	netdev->mtu = (unsigned int)new_mtu;
 
 	/* if VSI is up, bring it down and then back up */
@@ -6561,21 +6639,18 @@
 		err = ice_down(vsi);
 		if (err) {
 			netdev_err(netdev, "change MTU if_down err %d\n", err);
-			goto event_after;
+			return err;
 		}
 
 		err = ice_up(vsi);
 		if (err) {
 			netdev_err(netdev, "change MTU if_up err %d\n", err);
-			goto event_after;
+			return err;
 		}
 	}
 
 	netdev_dbg(netdev, "changed MTU to %d\n", new_mtu);
-event_after:
-	set_bit(IIDC_EVENT_AFTER_MTU_CHANGE, event->type);
-	ice_send_event_to_aux(pf, event);
-	kfree(event);
+	set_bit(ICE_FLAG_MTU_CHANGED, pf->flags);
 
 	return err;
 }
@@ -6934,6 +7009,8 @@
 	pf_sw = pf->first_sw;
 	/* find the attribute in the netlink message */
 	br_spec = nlmsg_find_attr(nlh, sizeof(struct ifinfomsg), IFLA_AF_SPEC);
+	if (!br_spec)
+		return -EINVAL;
 
 	nla_for_each_nested(attr, br_spec, rem) {
 		__u16 mode;
@@ -7190,6 +7267,7 @@
 		   struct net_device __always_unused *netdev,
 		   netdev_features_t features)
 {
+	bool gso = skb_is_gso(skb);
 	size_t len;
 
 	/* No point in doing any of this if neither checksum nor GSO are
@@ -7202,24 +7280,32 @@
 	/* We cannot support GSO if the MSS is going to be less than
 	 * 64 bytes. If it is then we need to drop support for GSO.
 	 */
-	if (skb_is_gso(skb) && (skb_shinfo(skb)->gso_size < 64))
+	if (gso && (skb_shinfo(skb)->gso_size < ICE_TXD_CTX_MIN_MSS))
 		features &= ~NETIF_F_GSO_MASK;
 
-	len = skb_network_header(skb) - skb->data;
+	len = skb_network_offset(skb);
 	if (len > ICE_TXD_MACLEN_MAX || len & 0x1)
 		goto out_rm_features;
 
-	len = skb_transport_header(skb) - skb_network_header(skb);
+	len = skb_network_header_len(skb);
 	if (len > ICE_TXD_IPLEN_MAX || len & 0x1)
 		goto out_rm_features;
 
 	if (skb->encapsulation) {
-		len = skb_inner_network_header(skb) - skb_transport_header(skb);
-		if (len > ICE_TXD_L4LEN_MAX || len & 0x1)
-			goto out_rm_features;
+		/* this must work for VXLAN frames AND IPIP/SIT frames, and in
+		 * the case of IPIP frames, the transport header pointer is
+		 * after the inner header! So check to make sure that this
+		 * is a GRE or UDP_TUNNEL frame before doing that math.
+		 */
+		if (gso && (skb_shinfo(skb)->gso_type &
+			    (SKB_GSO_GRE | SKB_GSO_UDP_TUNNEL))) {
+			len = skb_inner_network_header(skb) -
+			      skb_transport_header(skb);
+			if (len > ICE_TXD_L4LEN_MAX || len & 0x1)
+				goto out_rm_features;
+		}
 
-		len = skb_inner_transport_header(skb) -
-		      skb_inner_network_header(skb);
+		len = skb_inner_network_header_len(skb);
 		if (len > ICE_TXD_IPLEN_MAX || len & 0x1)
 			goto out_rm_features;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_ptp.c
@@ -254,12 +254,19 @@
  * This function must be called periodically to ensure that the cached value
  * is never more than 2 seconds old. It must also be called whenever the PHC
  * time has been changed.
+ *
+ * Return:
+ * * 0 - OK, successfully updated
+ * * -EAGAIN - PF was busy, need to reschedule the update
  */
-static void ice_ptp_update_cached_phctime(struct ice_pf *pf)
+static int ice_ptp_update_cached_phctime(struct ice_pf *pf)
 {
 	u64 systime;
 	int i;
 
+	if (test_and_set_bit(ICE_CFG_BUSY, pf->state))
+		return -EAGAIN;
+
 	/* Read the current PHC time */
 	systime = ice_ptp_read_src_clk_reg(pf, NULL);
 
@@ -282,6 +289,9 @@
 			WRITE_ONCE(vsi->rx_rings[j]->cached_phctime, systime);
 		}
 	}
+	clear_bit(ICE_CFG_BUSY, pf->state);
+
+	return 0;
 }
 
 /**
@@ -459,7 +469,7 @@
 		scaled_ppm = -scaled_ppm;
 	}
 
-	while ((u64)scaled_ppm > div_u64(U64_MAX, incval)) {
+	while ((u64)scaled_ppm > div64_u64(U64_MAX, incval)) {
 		/* handle overflow by scaling down the scaled_ppm and
 		 * the divisor, losing some precision
 		 */
@@ -846,9 +856,12 @@
 static int ice_ptp_adjtime_nonatomic(struct ptp_clock_info *info, s64 delta)
 {
 	struct timespec64 now, then;
+	int ret;
 
 	then = ns_to_timespec64(delta);
-	ice_ptp_gettimex64(info, &now, NULL);
+	ret = ice_ptp_gettimex64(info, &now, NULL);
+	if (ret)
+		return ret;
 	now = timespec64_add(now, then);
 
 	return ice_ptp_settime64(info, (const struct timespec64 *)&now);
@@ -1077,7 +1090,7 @@
 	snprintf(info->name, sizeof(info->name) - 1, "%s-%s-clk",
 		 dev_driver_string(dev), dev_name(dev));
 	info->owner = THIS_MODULE;
-	info->max_adj = 999999999;
+	info->max_adj = 100000000;
 	info->adjtime = ice_ptp_adjtime;
 	info->adjfine = ice_ptp_adjfine;
 	info->gettimex64 = ice_ptp_gettimex64;
@@ -1182,19 +1195,16 @@
 		if (err)
 			continue;
 
-		/* Check if the timestamp is valid */
-		if (!(raw_tstamp & ICE_PTP_TS_VALID))
+		/* Check if the timestamp is invalid or stale */
+		if (!(raw_tstamp & ICE_PTP_TS_VALID) ||
+		    raw_tstamp == tx->tstamps[idx].cached_tstamp)
 			continue;
 
-		/* clear the timestamp register, so that it won't show valid
-		 * again when re-used.
-		 */
-		ice_clear_phy_tstamp(hw, tx->quad, phy_idx);
-
 		/* The timestamp is valid, so we'll go ahead and clear this
 		 * index and then send the timestamp up to the stack.
 		 */
 		spin_lock(&tx->lock);
+		tx->tstamps[idx].cached_tstamp = raw_tstamp;
 		clear_bit(idx, tx->in_use);
 		skb = tx->tstamps[idx].skb;
 		tx->tstamps[idx].skb = NULL;
@@ -1375,6 +1385,7 @@
 
 /**
  * ice_ptp_tx_tstamp_cleanup - Cleanup old timestamp requests that got dropped
+ * @hw: pointer to the hw struct
  * @tx: PTP Tx tracker to clean up
  *
  * Loop through the Tx timestamp requests and see if any of them have been
@@ -1383,7 +1394,7 @@
  * timestamp will never be captured. This might happen if the packet gets
  * discarded before it reaches the PHY timestamping block.
  */
-static void ice_ptp_tx_tstamp_cleanup(struct ice_ptp_tx *tx)
+static void ice_ptp_tx_tstamp_cleanup(struct ice_hw *hw, struct ice_ptp_tx *tx)
 {
 	u8 idx;
 
@@ -1392,11 +1403,16 @@
 
 	for_each_set_bit(idx, tx->in_use, tx->len) {
 		struct sk_buff *skb;
+		u64 raw_tstamp;
 
 		/* Check if this SKB has been waiting for too long */
 		if (time_is_after_jiffies(tx->tstamps[idx].start + 2 * HZ))
 			continue;
 
+		/* Read tstamp to be able to use this register again */
+		ice_read_phy_tstamp(hw, tx->quad, idx + tx->quad_offset,
+				    &raw_tstamp);
+
 		spin_lock(&tx->lock);
 		skb = tx->tstamps[idx].skb;
 		tx->tstamps[idx].skb = NULL;
@@ -1412,17 +1428,18 @@
 {
 	struct ice_ptp *ptp = container_of(work, struct ice_ptp, work.work);
 	struct ice_pf *pf = container_of(ptp, struct ice_pf, ptp);
+	int err;
 
 	if (!test_bit(ICE_FLAG_PTP, pf->flags))
 		return;
 
-	ice_ptp_update_cached_phctime(pf);
+	err = ice_ptp_update_cached_phctime(pf);
 
-	ice_ptp_tx_tstamp_cleanup(&pf->ptp.port.tx);
+	ice_ptp_tx_tstamp_cleanup(&pf->hw, &pf->ptp.port.tx);
 
-	/* Run twice a second */
+	/* Run twice a second or reschedule if phc update failed */
 	kthread_queue_delayed_work(ptp->kworker, &ptp->work,
-				   msecs_to_jiffies(500));
+				   msecs_to_jiffies(err ? 10 : 500));
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_ptp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_ptp.h
@@ -46,15 +46,21 @@
  * struct ice_tx_tstamp - Tracking for a single Tx timestamp
  * @skb: pointer to the SKB for this timestamp request
  * @start: jiffies when the timestamp was first requested
+ * @cached_tstamp: last read timestamp
  *
  * This structure tracks a single timestamp request. The SKB pointer is
  * provided when initiating a request. The start time is used to ensure that
  * we discard old requests that were not fulfilled within a 2 second time
  * window.
+ * Timestamp values in the PHY are read only and do not get cleared except at
+ * hardware reset or when a new timestamp value is captured. The cached_tstamp
+ * field is used to detect the case where a new timestamp has not yet been
+ * captured, ensuring that we avoid sending stale timestamp data to the stack.
  */
 struct ice_tx_tstamp {
 	struct sk_buff *skb;
 	unsigned long start;
+	u64 cached_tstamp;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_sched.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_sched.c
@@ -27,9 +27,8 @@
 	if (!root)
 		return ICE_ERR_NO_MEMORY;
 
-	/* coverity[suspicious_sizeof] */
 	root->children = devm_kcalloc(ice_hw_to_dev(hw), hw->max_children[0],
-				      sizeof(*root), GFP_KERNEL);
+				      sizeof(*root->children), GFP_KERNEL);
 	if (!root->children) {
 		devm_kfree(ice_hw_to_dev(hw), root);
 		return ICE_ERR_NO_MEMORY;
@@ -180,10 +179,9 @@
 	if (!node)
 		return ICE_ERR_NO_MEMORY;
 	if (hw->max_children[layer]) {
-		/* coverity[suspicious_sizeof] */
 		node->children = devm_kcalloc(ice_hw_to_dev(hw),
 					      hw->max_children[layer],
-					      sizeof(*node), GFP_KERNEL);
+					      sizeof(*node->children), GFP_KERNEL);
 		if (!node->children) {
 			devm_kfree(ice_hw_to_dev(hw), node);
 			return ICE_ERR_NO_MEMORY;
@@ -2758,7 +2756,7 @@
 ice_sched_assoc_vsi_to_agg(struct ice_port_info *pi, u32 agg_id,
 			   u16 vsi_handle, unsigned long *tc_bitmap)
 {
-	struct ice_sched_agg_vsi_info *agg_vsi_info, *old_agg_vsi_info = NULL;
+	struct ice_sched_agg_vsi_info *agg_vsi_info, *iter, *old_agg_vsi_info = NULL;
 	struct ice_sched_agg_info *agg_info, *old_agg_info;
 	enum ice_status status = 0;
 	struct ice_hw *hw = pi->hw;
@@ -2776,11 +2774,13 @@
 	if (old_agg_info && old_agg_info != agg_info) {
 		struct ice_sched_agg_vsi_info *vtmp;
 
-		list_for_each_entry_safe(old_agg_vsi_info, vtmp,
+		list_for_each_entry_safe(iter, vtmp,
 					 &old_agg_info->agg_vsi_list,
 					 list_entry)
-			if (old_agg_vsi_info->vsi_handle == vsi_handle)
+			if (iter->vsi_handle == vsi_handle) {
+				old_agg_vsi_info = iter;
 				break;
+			}
 	}
 
 	/* check if entry already exist */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_switch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_switch.c
@@ -1286,7 +1286,7 @@
 
 		/* A rule already exists with the new VSI being added */
 		if (test_bit(vsi_handle, m_entry->vsi_list_info->vsi_map))
-			return 0;
+			return -EEXIST;
 
 		/* Update the previously created VSI list set with
 		 * the new VSI ID passed in
@@ -2614,7 +2614,7 @@
 		else
 			status = ice_set_vsi_promisc(hw, vsi_handle,
 						     promisc_mask, vlan_id);
-		if (status)
+		if (status && status != -EEXIST)
 			break;
 	}
 
@@ -2812,8 +2812,6 @@
 		if (!itr->vsi_list_info ||
 		    !test_bit(vsi_handle, itr->vsi_list_info->vsi_map))
 			continue;
-		/* Clearing it so that the logic can add it back */
-		clear_bit(vsi_handle, itr->vsi_list_info->vsi_map);
 		f_entry.fltr_info.vsi_handle = vsi_handle;
 		f_entry.fltr_info.fltr_act = ICE_FWD_TO_VSI;
 		/* update the src in case it is VSI num */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_txrx.c
@@ -765,7 +765,7 @@
 		return false;
 #else
 #define ICE_LAST_OFFSET \
-	(SKB_WITH_OVERHEAD(PAGE_SIZE) - ICE_RXBUF_2048)
+	(SKB_WITH_OVERHEAD(PAGE_SIZE) - ICE_RXBUF_3072)
 	if (rx_buf->page_offset > ICE_LAST_OFFSET)
 		return false;
 #endif /* PAGE_SIZE < 8192) */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_txrx.h
@@ -164,17 +164,10 @@
 };
 
 struct ice_rx_buf {
-	union {
-		struct {
-			dma_addr_t dma;
-			struct page *page;
-			unsigned int page_offset;
-			u16 pagecnt_bias;
-		};
-		struct {
-			struct xdp_buff *xdp;
-		};
-	};
+	dma_addr_t dma;
+	struct page *page;
+	unsigned int page_offset;
+	u16 pagecnt_bias;
 };
 
 struct ice_q_stats {
@@ -270,6 +263,7 @@
 	union {
 		struct ice_tx_buf *tx_buf;
 		struct ice_rx_buf *rx_buf;
+		struct xdp_buff **xdp_buf;
 	};
 	/* CL2 - 2nd cacheline starts here */
 	u16 q_index;			/* Queue number of ring */
@@ -338,6 +332,11 @@
 	return !!(ring->flags & ICE_TX_FLAGS_RING_XDP);
 }
 
+enum ice_container_type {
+	ICE_RX_CONTAINER,
+	ICE_TX_CONTAINER,
+};
+
 struct ice_ring_container {
 	/* head of linked-list of rings */
 	struct ice_ring *ring;
@@ -346,9 +345,15 @@
 	/* this matches the maximum number of ITR bits, but in usec
 	 * values, so it is shifted left one bit (bit zero is ignored)
 	 */
-	u16 itr_setting:13;
-	u16 itr_reserved:2;
-	u16 itr_mode:1;
+	union {
+		struct {
+			u16 itr_setting:13;
+			u16 itr_reserved:2;
+			u16 itr_mode:1;
+		};
+		u16 itr_settings;
+	};
+	enum ice_container_type type;
 };
 
 struct ice_coalesce_stored {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_type.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_type.h
@@ -268,6 +268,8 @@
 	u8 dcb;
 	u8 ieee_1588;
 	u8 rdma;
+	u8 roce_lag;
+	u8 sriov_lag;
 
 	bool nvm_update_pending_nvm;
 	bool nvm_update_pending_orom;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_virtchnl_fdir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_virtchnl_fdir.c
@@ -732,6 +732,89 @@
 }
 
 /**
+ * ice_vc_fdir_reset_cnt_all - reset all FDIR counters for this VF FDIR
+ * @fdir: pointer to the VF FDIR structure
+ */
+static void ice_vc_fdir_reset_cnt_all(struct ice_vf_fdir *fdir)
+{
+	enum ice_fltr_ptype flow;
+
+	for (flow = ICE_FLTR_PTYPE_NONF_NONE;
+	     flow < ICE_FLTR_PTYPE_MAX; flow++) {
+		fdir->fdir_fltr_cnt[flow][0] = 0;
+		fdir->fdir_fltr_cnt[flow][1] = 0;
+	}
+
+	fdir->fdir_fltr_cnt_total = 0;
+}
+
+/**
+ * ice_vc_fdir_has_prof_conflict
+ * @vf: pointer to the VF structure
+ * @conf: FDIR configuration for each filter
+ *
+ * Check if @conf has conflicting profile with existing profiles
+ *
+ * Return: true on success, and false on error.
+ */
+static bool
+ice_vc_fdir_has_prof_conflict(struct ice_vf *vf,
+			      struct virtchnl_fdir_fltr_conf *conf)
+{
+	struct ice_fdir_fltr *desc;
+
+	list_for_each_entry(desc, &vf->fdir.fdir_rule_list, fltr_node) {
+		struct virtchnl_fdir_fltr_conf *existing_conf;
+		enum ice_fltr_ptype flow_type_a, flow_type_b;
+		struct ice_fdir_fltr *a, *b;
+
+		existing_conf = to_fltr_conf_from_desc(desc);
+		a = &existing_conf->input;
+		b = &conf->input;
+		flow_type_a = a->flow_type;
+		flow_type_b = b->flow_type;
+
+		/* No need to compare two rules with different tunnel types or
+		 * with the same protocol type.
+		 */
+		if (existing_conf->ttype != conf->ttype ||
+		    flow_type_a == flow_type_b)
+			continue;
+
+		switch (flow_type_a) {
+		case ICE_FLTR_PTYPE_NONF_IPV4_UDP:
+		case ICE_FLTR_PTYPE_NONF_IPV4_TCP:
+		case ICE_FLTR_PTYPE_NONF_IPV4_SCTP:
+			if (flow_type_b == ICE_FLTR_PTYPE_NONF_IPV4_OTHER)
+				return true;
+			break;
+		case ICE_FLTR_PTYPE_NONF_IPV4_OTHER:
+			if (flow_type_b == ICE_FLTR_PTYPE_NONF_IPV4_UDP ||
+			    flow_type_b == ICE_FLTR_PTYPE_NONF_IPV4_TCP ||
+			    flow_type_b == ICE_FLTR_PTYPE_NONF_IPV4_SCTP)
+				return true;
+			break;
+		case ICE_FLTR_PTYPE_NONF_IPV6_UDP:
+		case ICE_FLTR_PTYPE_NONF_IPV6_TCP:
+		case ICE_FLTR_PTYPE_NONF_IPV6_SCTP:
+			if (flow_type_b == ICE_FLTR_PTYPE_NONF_IPV6_OTHER)
+				return true;
+			break;
+		case ICE_FLTR_PTYPE_NONF_IPV6_OTHER:
+			if (flow_type_b == ICE_FLTR_PTYPE_NONF_IPV6_UDP ||
+			    flow_type_b == ICE_FLTR_PTYPE_NONF_IPV6_TCP ||
+			    flow_type_b == ICE_FLTR_PTYPE_NONF_IPV6_SCTP)
+				return true;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return false;
+}
+
+/**
  * ice_vc_fdir_write_flow_prof
  * @vf: pointer to the VF structure
  * @flow: filter flow type
@@ -871,6 +954,13 @@
 	enum ice_fltr_ptype flow;
 	int ret;
 
+	ret = ice_vc_fdir_has_prof_conflict(vf, conf);
+	if (ret) {
+		dev_dbg(dev, "Found flow profile conflict for VF %d\n",
+			vf->vf_id);
+		return ret;
+	}
+
 	flow = input->flow_type;
 	ret = ice_vc_fdir_alloc_prof(vf, flow);
 	if (ret) {
@@ -1749,6 +1839,7 @@
 	resp->status = status;
 	resp->flow_id = conf->flow_id;
 	vf->fdir.fdir_fltr_cnt[conf->input.flow_type][is_tun]++;
+	vf->fdir.fdir_fltr_cnt_total++;
 
 	ret = ice_vc_send_msg_to_vf(vf, ctx->v_opcode, v_ret,
 				    (u8 *)resp, len);
@@ -1813,6 +1904,7 @@
 	resp->status = status;
 	ice_vc_fdir_remove_entry(vf, conf, conf->flow_id);
 	vf->fdir.fdir_fltr_cnt[conf->input.flow_type][is_tun]--;
+	vf->fdir.fdir_fltr_cnt_total--;
 
 	ret = ice_vc_send_msg_to_vf(vf, ctx->v_opcode, v_ret,
 				    (u8 *)resp, len);
@@ -1977,6 +2069,7 @@
 	struct virtchnl_fdir_add *stat = NULL;
 	struct virtchnl_fdir_fltr_conf *conf;
 	enum virtchnl_status_code v_ret;
+	struct ice_vsi *vf_vsi;
 	struct device *dev;
 	struct ice_pf *pf;
 	int is_tun = 0;
@@ -1985,6 +2078,17 @@
 
 	pf = vf->pf;
 	dev = ice_pf_to_dev(pf);
+	vf_vsi = ice_get_vf_vsi(vf);
+
+#define ICE_VF_MAX_FDIR_FILTERS	128
+	if (!ice_fdir_num_avail_fltr(&pf->hw, vf_vsi) ||
+	    vf->fdir.fdir_fltr_cnt_total >= ICE_VF_MAX_FDIR_FILTERS) {
+		v_ret = VIRTCHNL_STATUS_ERR_PARAM;
+		dev_err(dev, "Max number of FDIR filters for VF %d is reached\n",
+			vf->vf_id);
+		goto err_exit;
+	}
+
 	ret = ice_vc_fdir_param_check(vf, fltr->vsi_id);
 	if (ret) {
 		v_ret = VIRTCHNL_STATUS_ERR_PARAM;
@@ -2063,7 +2167,7 @@
 		v_ret = VIRTCHNL_STATUS_SUCCESS;
 		stat->status = VIRTCHNL_FDIR_FAILURE_RULE_NORESOURCE;
 		dev_dbg(dev, "VF %d: set FDIR context failed\n", vf->vf_id);
-		goto err_free_conf;
+		goto err_rem_entry;
 	}
 
 	ret = ice_vc_fdir_write_fltr(vf, conf, true, is_tun);
@@ -2072,15 +2176,16 @@
 		stat->status = VIRTCHNL_FDIR_FAILURE_RULE_NORESOURCE;
 		dev_err(dev, "VF %d: writing FDIR rule failed, ret:%d\n",
 			vf->vf_id, ret);
-		goto err_rem_entry;
+		goto err_clr_irq;
 	}
 
 exit:
 	kfree(stat);
 	return ret;
 
-err_rem_entry:
+err_clr_irq:
 	ice_vc_fdir_clear_irq_ctx(vf);
+err_rem_entry:
 	ice_vc_fdir_remove_entry(vf, conf, conf->flow_id);
 err_free_conf:
 	devm_kfree(dev, conf);
@@ -2189,6 +2294,7 @@
 	spin_lock_init(&fdir->ctx_lock);
 	fdir->ctx_irq.flags = 0;
 	fdir->ctx_done.flags = 0;
+	ice_vc_fdir_reset_cnt_all(fdir);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_virtchnl_fdir.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_virtchnl_fdir.h
@@ -28,6 +28,7 @@
 struct ice_vf_fdir {
 	u16 fdir_fltr_cnt[ICE_FLTR_PTYPE_MAX][ICE_FD_HW_SEG_MAX];
 	int prof_entry_cnt[ICE_FLTR_PTYPE_MAX][ICE_FD_HW_SEG_MAX];
+	u16 fdir_fltr_cnt_total;
 	struct ice_fd_hw_prof **fdir_prof;
 
 	struct idr fdir_rule_idr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
@@ -251,7 +251,7 @@
  * ice_get_vf_vsi - get VF's VSI based on the stored index
  * @vf: VF used to get VSI
  */
-static struct ice_vsi *ice_get_vf_vsi(struct ice_vf *vf)
+struct ice_vsi *ice_get_vf_vsi(struct ice_vf *vf)
 {
 	return vf->pf->vsi[vf->lan_vsi_idx];
 }
@@ -615,8 +615,6 @@
 	struct ice_hw *hw = &pf->hw;
 	unsigned int tmp, i;
 
-	set_bit(ICE_VF_DEINIT_IN_PROGRESS, pf->state);
-
 	if (!pf->vf)
 		return;
 
@@ -632,21 +630,26 @@
 	else
 		dev_warn(dev, "VFs are assigned - not disabling SR-IOV\n");
 
-	/* Avoid wait time by stopping all VFs at the same time */
-	ice_for_each_vf(pf, i)
-		if (test_bit(ICE_VF_STATE_QS_ENA, pf->vf[i].vf_states))
-			ice_dis_vf_qs(&pf->vf[i]);
-
 	tmp = pf->num_alloc_vfs;
 	pf->num_qps_per_vf = 0;
 	pf->num_alloc_vfs = 0;
 	for (i = 0; i < tmp; i++) {
-		if (test_bit(ICE_VF_STATE_INIT, pf->vf[i].vf_states)) {
+		struct ice_vf *vf = &pf->vf[i];
+
+		mutex_lock(&vf->cfg_lock);
+
+		ice_dis_vf_qs(vf);
+
+		if (test_bit(ICE_VF_STATE_INIT, vf->vf_states)) {
 			/* disable VF qp mappings and set VF disable state */
-			ice_dis_vf_mappings(&pf->vf[i]);
-			set_bit(ICE_VF_STATE_DIS, pf->vf[i].vf_states);
-			ice_free_vf_res(&pf->vf[i]);
+			ice_dis_vf_mappings(vf);
+			set_bit(ICE_VF_STATE_DIS, vf->vf_states);
+			ice_free_vf_res(vf);
 		}
+
+		mutex_unlock(&vf->cfg_lock);
+
+		mutex_destroy(&vf->cfg_lock);
 	}
 
 	if (ice_sriov_free_msix_res(pf))
@@ -682,7 +685,6 @@
 				i);
 
 	clear_bit(ICE_VF_DIS, pf->state);
-	clear_bit(ICE_VF_DEINIT_IN_PROGRESS, pf->state);
 	clear_bit(ICE_FLAG_SRIOV_ENA, pf->flags);
 }
 
@@ -1566,10 +1568,13 @@
 	ice_for_each_vf(pf, v) {
 		vf = &pf->vf[v];
 
+		mutex_lock(&vf->cfg_lock);
+
 		vf->driver_caps = 0;
 		ice_vc_set_default_allowlist(vf);
 
 		ice_vf_fdir_exit(vf);
+		ice_vf_fdir_init(vf);
 		/* clean VF control VSI when resetting VFs since it should be
 		 * setup only when VF creates its first FDIR rule.
 		 */
@@ -1579,6 +1584,8 @@
 		ice_vf_pre_vsi_rebuild(vf);
 		ice_vf_rebuild_vsi(vf);
 		ice_vf_post_vsi_rebuild(vf);
+
+		mutex_unlock(&vf->cfg_lock);
 	}
 
 	ice_flush(hw);
@@ -1625,6 +1632,8 @@
 	u32 reg;
 	int i;
 
+	lockdep_assert_held(&vf->cfg_lock);
+
 	dev = ice_pf_to_dev(pf);
 
 	if (test_bit(ICE_VF_RESETS_DISABLED, pf->state)) {
@@ -1645,8 +1654,7 @@
 
 	vsi = ice_get_vf_vsi(vf);
 
-	if (test_bit(ICE_VF_STATE_QS_ENA, vf->vf_states))
-		ice_dis_vf_qs(vf);
+	ice_dis_vf_qs(vf);
 
 	/* Call Disable LAN Tx queue AQ whether or not queues are
 	 * enabled. This is needed for successful completion of VFR.
@@ -1697,6 +1705,7 @@
 	}
 
 	ice_vf_fdir_exit(vf);
+	ice_vf_fdir_init(vf);
 	/* clean VF control VSI when resetting VF since it should be setup
 	 * only when VF creates its first FDIR rule.
 	 */
@@ -1894,6 +1903,8 @@
 		 */
 		ice_vf_ctrl_invalidate_vsi(vf);
 		ice_vf_fdir_init(vf);
+
+		mutex_init(&vf->cfg_lock);
 	}
 }
 
@@ -2109,9 +2120,12 @@
 		bit_idx = (hw->func_caps.vf_base_id + vf_id) % 32;
 		/* read GLGEN_VFLRSTAT register to find out the flr VFs */
 		reg = rd32(hw, GLGEN_VFLRSTAT(reg_idx));
-		if (reg & BIT(bit_idx))
+		if (reg & BIT(bit_idx)) {
 			/* GLGEN_VFLRSTAT bit will be cleared in ice_reset_vf */
+			mutex_lock(&vf->cfg_lock);
 			ice_reset_vf(vf, true);
+			mutex_unlock(&vf->cfg_lock);
+		}
 	}
 }
 
@@ -2188,7 +2202,9 @@
 	if (!vf)
 		return;
 
+	mutex_lock(&vf->cfg_lock);
 	ice_vc_reset_vf(vf);
+	mutex_unlock(&vf->cfg_lock);
 }
 
 /**
@@ -2218,24 +2234,6 @@
 
 	dev = ice_pf_to_dev(pf);
 
-	/* single place to detect unsuccessful return values */
-	if (v_retval) {
-		vf->num_inval_msgs++;
-		dev_info(dev, "VF %d failed opcode %d, retval: %d\n", vf->vf_id,
-			 v_opcode, v_retval);
-		if (vf->num_inval_msgs > ICE_DFLT_NUM_INVAL_MSGS_ALLOWED) {
-			dev_err(dev, "Number of invalid messages exceeded for VF %d\n",
-				vf->vf_id);
-			dev_err(dev, "Use PF Control I/F to enable the VF\n");
-			set_bit(ICE_VF_STATE_DIS, vf->vf_states);
-			return -EIO;
-		}
-	} else {
-		vf->num_valid_msgs++;
-		/* reset the invalid counter, if a valid message is received. */
-		vf->num_inval_msgs = 0;
-	}
-
 	aq_ret = ice_aq_send_msg_to_vf(&pf->hw, vf->vf_id, v_opcode, v_retval,
 				       msg, msglen, NULL);
 	if (aq_ret && pf->hw.mailboxq.sq_last_status != ICE_AQ_RC_ENOSYS) {
@@ -2954,6 +2952,7 @@
 static int ice_vc_cfg_promiscuous_mode_msg(struct ice_vf *vf, u8 *msg)
 {
 	enum virtchnl_status_code v_ret = VIRTCHNL_STATUS_SUCCESS;
+	enum ice_status mcast_status = 0, ucast_status = 0;
 	bool rm_promisc, alluni = false, allmulti = false;
 	struct virtchnl_promisc_info *info =
 	    (struct virtchnl_promisc_info *)msg;
@@ -3043,52 +3042,51 @@
 			goto error_param;
 		}
 	} else {
-		enum ice_status status;
-		u8 promisc_m;
+		u8 mcast_m, ucast_m;
 
-		if (alluni) {
-			if (vf->port_vlan_info || vsi->num_vlan)
-				promisc_m = ICE_UCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_UCAST_PROMISC_BITS;
-		} else if (allmulti) {
-			if (vf->port_vlan_info || vsi->num_vlan)
-				promisc_m = ICE_MCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_MCAST_PROMISC_BITS;
+		if (vf->port_vlan_info || vsi->num_vlan > 1) {
+			mcast_m = ICE_MCAST_VLAN_PROMISC_BITS;
+			ucast_m = ICE_UCAST_VLAN_PROMISC_BITS;
 		} else {
-			if (vf->port_vlan_info || vsi->num_vlan)
-				promisc_m = ICE_UCAST_VLAN_PROMISC_BITS;
-			else
-				promisc_m = ICE_UCAST_PROMISC_BITS;
+			mcast_m = ICE_MCAST_PROMISC_BITS;
+			ucast_m = ICE_UCAST_PROMISC_BITS;
 		}
 
-		/* Configure multicast/unicast with or without VLAN promiscuous
-		 * mode
-		 */
-		status = ice_vf_set_vsi_promisc(vf, vsi, promisc_m, rm_promisc);
-		if (status) {
-			dev_err(dev, "%sable Tx/Rx filter promiscuous mode on VF-%d failed, error: %s\n",
-				rm_promisc ? "dis" : "en", vf->vf_id,
-				ice_stat_str(status));
-			v_ret = ice_err_to_virt_err(status);
-			goto error_param;
-		} else {
-			dev_dbg(dev, "%sable Tx/Rx filter promiscuous mode on VF-%d succeeded\n",
-				rm_promisc ? "dis" : "en", vf->vf_id);
+		ucast_status = ice_vf_set_vsi_promisc(vf, vsi, ucast_m,
+						      !alluni);
+		if (ucast_status) {
+			dev_err(dev, "%sable Tx/Rx filter promiscuous mode on VF-%d failed\n",
+				alluni ? "en" : "dis", vf->vf_id);
+			v_ret = ice_err_to_virt_err(ucast_status);
+		}
+
+		mcast_status = ice_vf_set_vsi_promisc(vf, vsi, mcast_m,
+						      !allmulti);
+		if (mcast_status) {
+			dev_err(dev, "%sable Tx/Rx filter promiscuous mode on VF-%d failed\n",
+				allmulti ? "en" : "dis", vf->vf_id);
+			v_ret = ice_err_to_virt_err(mcast_status);
 		}
 	}
 
-	if (allmulti &&
-	    !test_and_set_bit(ICE_VF_STATE_MC_PROMISC, vf->vf_states))
-		dev_info(dev, "VF %u successfully set multicast promiscuous mode\n", vf->vf_id);
-	else if (!allmulti && test_and_clear_bit(ICE_VF_STATE_MC_PROMISC, vf->vf_states))
-		dev_info(dev, "VF %u successfully unset multicast promiscuous mode\n", vf->vf_id);
-
-	if (alluni && !test_and_set_bit(ICE_VF_STATE_UC_PROMISC, vf->vf_states))
-		dev_info(dev, "VF %u successfully set unicast promiscuous mode\n", vf->vf_id);
-	else if (!alluni && test_and_clear_bit(ICE_VF_STATE_UC_PROMISC, vf->vf_states))
-		dev_info(dev, "VF %u successfully unset unicast promiscuous mode\n", vf->vf_id);
+	if (!mcast_status) {
+		if (allmulti &&
+		    !test_and_set_bit(ICE_VF_STATE_MC_PROMISC, vf->vf_states))
+			dev_info(dev, "VF %u successfully set multicast promiscuous mode\n",
+				 vf->vf_id);
+		else if (!allmulti && test_and_clear_bit(ICE_VF_STATE_MC_PROMISC, vf->vf_states))
+			dev_info(dev, "VF %u successfully unset multicast promiscuous mode\n",
+				 vf->vf_id);
+	}
+
+	if (!ucast_status) {
+		if (alluni && !test_and_set_bit(ICE_VF_STATE_UC_PROMISC, vf->vf_states))
+			dev_info(dev, "VF %u successfully set unicast promiscuous mode\n",
+				 vf->vf_id);
+		else if (!alluni && test_and_clear_bit(ICE_VF_STATE_UC_PROMISC, vf->vf_states))
+			dev_info(dev, "VF %u successfully unset unicast promiscuous mode\n",
+				 vf->vf_id);
+	}
 
 error_param:
 	return ice_vc_send_msg_to_vf(vf, VIRTCHNL_OP_CONFIG_PROMISCUOUS_MODE,
@@ -3337,9 +3335,9 @@
 				goto error_param;
 			}
 
-			/* Skip queue if not enabled */
 			if (!test_bit(vf_q_id, vf->txq_ena))
-				continue;
+				dev_dbg(ice_pf_to_dev(vsi->back), "Queue %u on VSI %u is not enabled, but stopping it anyway\n",
+					vf_q_id, vsi->vsi_num);
 
 			ice_fill_txq_meta(vsi, ring, &txq_meta);
 
@@ -3762,6 +3760,7 @@
 	struct device *dev = ice_pf_to_dev(vf->pf);
 	u8 *mac_addr = vc_ether_addr->addr;
 	enum ice_status status;
+	int ret = 0;
 
 	/* device MAC already added */
 	if (ether_addr_equal(mac_addr, vf->dev_lan_addr.addr))
@@ -3774,20 +3773,23 @@
 
 	status = ice_fltr_add_mac(vsi, mac_addr, ICE_FWD_TO_VSI);
 	if (status == ICE_ERR_ALREADY_EXISTS) {
-		dev_err(dev, "MAC %pM already exists for VF %d\n", mac_addr,
+		dev_dbg(dev, "MAC %pM already exists for VF %d\n", mac_addr,
 			vf->vf_id);
-		return -EEXIST;
+		/* don't return since we might need to update
+		 * the primary MAC in ice_vfhw_mac_add() below
+		 */
+		ret = -EEXIST;
 	} else if (status) {
 		dev_err(dev, "Failed to add MAC %pM for VF %d\n, error %s\n",
 			mac_addr, vf->vf_id, ice_stat_str(status));
 		return -EIO;
+	} else {
+		vf->num_mac++;
 	}
 
 	ice_vfhw_mac_add(vf, vc_ether_addr);
 
-	vf->num_mac++;
-
-	return 0;
+	return ret;
 }
 
 /**
@@ -4078,6 +4080,8 @@
 		return 0;
 	}
 
+	mutex_lock(&vf->cfg_lock);
+
 	vf->port_vlan_info = vlanprio;
 
 	if (vf->port_vlan_info)
@@ -4087,6 +4091,7 @@
 		dev_info(dev, "Clearing port VLAN on VF %d\n", vf_id);
 
 	ice_vc_reset_vf(vf);
+	mutex_unlock(&vf->cfg_lock);
 
 	return 0;
 }
@@ -4418,10 +4423,6 @@
 	struct device *dev;
 	int err = 0;
 
-	/* if de-init is underway, don't process messages from VF */
-	if (test_bit(ICE_VF_DEINIT_IN_PROGRESS, pf->state))
-		return;
-
 	dev = ice_pf_to_dev(pf);
 	if (ice_validate_vf_id(pf, vf_id)) {
 		err = -EINVAL;
@@ -4461,6 +4462,15 @@
 		return;
 	}
 
+	/* VF is being configured in another context that triggers a VFR, so no
+	 * need to process this message
+	 */
+	if (!mutex_trylock(&vf->cfg_lock)) {
+		dev_info(dev, "VF %u is being configured in another context that will trigger a VFR, so there is no need to handle this message\n",
+			 vf->vf_id);
+		return;
+	}
+
 	switch (v_opcode) {
 	case VIRTCHNL_OP_VERSION:
 		err = ice_vc_get_ver_msg(vf, msg);
@@ -4549,6 +4559,8 @@
 		dev_info(dev, "PF failed to honor VF %d, opcode %d, error %d\n",
 			 vf_id, v_opcode, err);
 	}
+
+	mutex_unlock(&vf->cfg_lock);
 }
 
 /**
@@ -4664,6 +4676,8 @@
 		return -EINVAL;
 	}
 
+	mutex_lock(&vf->cfg_lock);
+
 	/* VF is notified of its new MAC via the PF's response to the
 	 * VIRTCHNL_OP_GET_VF_RESOURCES message after the VF has been reset
 	 */
@@ -4682,6 +4696,7 @@
 	}
 
 	ice_vc_reset_vf(vf);
+	mutex_unlock(&vf->cfg_lock);
 	return 0;
 }
 
@@ -4711,11 +4726,15 @@
 	if (trusted == vf->trusted)
 		return 0;
 
+	mutex_lock(&vf->cfg_lock);
+
 	vf->trusted = trusted;
 	ice_vc_reset_vf(vf);
 	dev_info(ice_pf_to_dev(pf), "VF %u is now %strusted\n",
 		 vf_id, trusted ? "" : "un");
 
+	mutex_unlock(&vf->cfg_lock);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.h
@@ -14,7 +14,6 @@
 #define ICE_MAX_MACADDR_PER_VF		18
 
 /* Malicious Driver Detection */
-#define ICE_DFLT_NUM_INVAL_MSGS_ALLOWED		10
 #define ICE_MDD_EVENTS_THRESHOLD		30
 
 /* Static VF transaction/status register def */
@@ -74,6 +73,11 @@
 struct ice_vf {
 	struct ice_pf *pf;
 
+	/* Used during virtchnl message handling and NDO ops against the VF
+	 * that will trigger a VFR
+	 */
+	struct mutex cfg_lock;
+
 	u16 vf_id;			/* VF ID in the PF space */
 	u16 lan_vsi_idx;		/* index into PF struct */
 	u16 ctrl_vsi_idx;
@@ -102,8 +106,6 @@
 	unsigned int tx_rate;		/* Tx bandwidth limit in Mbps */
 	DECLARE_BITMAP(vf_states, ICE_VF_STATES_NBITS);	/* VF runtime states */
 
-	u64 num_inval_msgs;		/* number of continuous invalid msgs */
-	u64 num_valid_msgs;		/* number of valid msgs detected */
 	unsigned long vf_caps;		/* VF's adv. capabilities */
 	u8 num_req_qs;			/* num of queue pairs requested by VF */
 	u16 num_mac;
@@ -111,9 +113,13 @@
 	struct ice_mdd_vf_events mdd_rx_events;
 	struct ice_mdd_vf_events mdd_tx_events;
 	DECLARE_BITMAP(opcodes_allowlist, VIRTCHNL_OP_MAX);
+
+	/* devlink port data */
+	struct devlink_port devlink_port;
 };
 
 #ifdef CONFIG_PCI_IOV
+struct ice_vsi *ice_get_vf_vsi(struct ice_vf *vf);
 void ice_process_vflr_event(struct ice_pf *pf);
 int ice_sriov_configure(struct pci_dev *pdev, int num_vfs);
 int ice_set_vf_mac(struct net_device *netdev, int vf_id, u8 *mac);
@@ -171,6 +177,11 @@
 static inline void ice_print_vf_rx_mdd_event(struct ice_vf *vf) { }
 static inline void ice_restore_all_vfs_msi_state(struct pci_dev *pdev) { }
 
+static inline struct ice_vsi *ice_get_vf_vsi(struct ice_vf *vf)
+{
+	return NULL;
+}
+
 static inline bool
 ice_is_malicious_vf(struct ice_pf __always_unused *pf,
 		    struct ice_rq_event_info __always_unused *event,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ice/ice_xsk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ice/ice_xsk.c
@@ -36,8 +36,10 @@
 static void ice_qp_clean_rings(struct ice_vsi *vsi, u16 q_idx)
 {
 	ice_clean_tx_ring(vsi->tx_rings[q_idx]);
-	if (ice_is_xdp_ena_vsi(vsi))
+	if (ice_is_xdp_ena_vsi(vsi)) {
+		synchronize_rcu();
 		ice_clean_tx_ring(vsi->xdp_rings[q_idx]);
+	}
 	ice_clean_rx_ring(vsi->rx_rings[q_idx]);
 }
 
@@ -164,8 +166,6 @@
 	}
 	netif_tx_stop_queue(netdev_get_tx_queue(vsi->netdev, q_idx));
 
-	ice_qvec_dis_irq(vsi, rx_ring, q_vector);
-
 	ice_fill_txq_meta(vsi, tx_ring, &txq_meta);
 	err = ice_vsi_stop_tx_ring(vsi, ICE_NO_RESET, 0, tx_ring, &txq_meta);
 	if (err)
@@ -180,6 +180,8 @@
 		if (err)
 			return err;
 	}
+	ice_qvec_dis_irq(vsi, rx_ring, q_vector);
+
 	err = ice_vsi_ctrl_one_rx_ring(vsi, false, q_idx, true);
 	if (err)
 		return err;
@@ -319,6 +321,19 @@
 	bool if_running, pool_present = !!pool;
 	int ret = 0, pool_failure = 0;
 
+	if (qid >= vsi->num_rxq || qid >= vsi->num_txq) {
+		netdev_err(vsi->netdev, "Please use queue id in scope of combined queues count\n");
+		pool_failure = -EINVAL;
+		goto failure;
+	}
+
+	if (!is_power_of_2(vsi->rx_rings[qid]->count) ||
+	    !is_power_of_2(vsi->tx_rings[qid]->count)) {
+		netdev_err(vsi->netdev, "Please align ring sizes to power of 2\n");
+		pool_failure = -EINVAL;
+		goto failure;
+	}
+
 	if_running = netif_running(vsi->netdev) && ice_is_xdp_ena_vsi(vsi);
 
 	if (if_running) {
@@ -341,6 +356,7 @@
 			netdev_err(vsi->netdev, "ice_qp_ena error = %d\n", ret);
 	}
 
+failure:
 	if (pool_failure) {
 		netdev_err(vsi->netdev, "Could not %sable buffer pool, error = %d\n",
 			   pool_present ? "en" : "dis", pool_failure);
@@ -364,7 +380,7 @@
 {
 	union ice_32b_rx_flex_desc *rx_desc;
 	u16 ntu = rx_ring->next_to_use;
-	struct ice_rx_buf *rx_buf;
+	struct xdp_buff **xdp;
 	bool ok = true;
 	dma_addr_t dma;
 
@@ -372,26 +388,26 @@
 		return true;
 
 	rx_desc = ICE_RX_DESC(rx_ring, ntu);
-	rx_buf = &rx_ring->rx_buf[ntu];
+	xdp = &rx_ring->xdp_buf[ntu];
 
 	do {
-		rx_buf->xdp = xsk_buff_alloc(rx_ring->xsk_pool);
-		if (!rx_buf->xdp) {
+		*xdp = xsk_buff_alloc(rx_ring->xsk_pool);
+		if (!*xdp) {
 			ok = false;
 			break;
 		}
 
-		dma = xsk_buff_xdp_get_dma(rx_buf->xdp);
+		dma = xsk_buff_xdp_get_dma(*xdp);
 		rx_desc->read.pkt_addr = cpu_to_le64(dma);
 		rx_desc->wb.status_error0 = 0;
 
 		rx_desc++;
-		rx_buf++;
+		xdp++;
 		ntu++;
 
 		if (unlikely(ntu == rx_ring->count)) {
 			rx_desc = ICE_RX_DESC(rx_ring, 0);
-			rx_buf = rx_ring->rx_buf;
+			xdp = rx_ring->xdp_buf;
 			ntu = 0;
 		}
 	} while (--count);
@@ -421,19 +437,19 @@
 /**
  * ice_construct_skb_zc - Create an sk_buff from zero-copy buffer
  * @rx_ring: Rx ring
- * @rx_buf: zero-copy Rx buffer
+ * @xdp_arr: Pointer to the SW ring of xdp_buff pointers
  *
  * This function allocates a new skb from a zero-copy Rx buffer.
  *
  * Returns the skb on success, NULL on failure.
  */
 static struct sk_buff *
-ice_construct_skb_zc(struct ice_ring *rx_ring, struct ice_rx_buf *rx_buf)
+ice_construct_skb_zc(struct ice_ring *rx_ring, struct xdp_buff **xdp_arr)
 {
-	unsigned int metasize = rx_buf->xdp->data - rx_buf->xdp->data_meta;
-	unsigned int datasize = rx_buf->xdp->data_end - rx_buf->xdp->data;
-	unsigned int datasize_hard = rx_buf->xdp->data_end -
-				     rx_buf->xdp->data_hard_start;
+	struct xdp_buff *xdp = *xdp_arr;
+	unsigned int metasize = xdp->data - xdp->data_meta;
+	unsigned int datasize = xdp->data_end - xdp->data;
+	unsigned int datasize_hard = xdp->data_end - xdp->data_hard_start;
 	struct sk_buff *skb;
 
 	skb = __napi_alloc_skb(&rx_ring->q_vector->napi, datasize_hard,
@@ -441,13 +457,13 @@
 	if (unlikely(!skb))
 		return NULL;
 
-	skb_reserve(skb, rx_buf->xdp->data - rx_buf->xdp->data_hard_start);
-	memcpy(__skb_put(skb, datasize), rx_buf->xdp->data, datasize);
+	skb_reserve(skb, xdp->data - xdp->data_hard_start);
+	memcpy(__skb_put(skb, datasize), xdp->data, datasize);
 	if (metasize)
 		skb_metadata_set(skb, metasize);
 
-	xsk_buff_free(rx_buf->xdp);
-	rx_buf->xdp = NULL;
+	xsk_buff_free(xdp);
+	*xdp_arr = NULL;
 	return skb;
 }
 
@@ -521,7 +537,7 @@
 	while (likely(total_rx_packets < (unsigned int)budget)) {
 		union ice_32b_rx_flex_desc *rx_desc;
 		unsigned int size, xdp_res = 0;
-		struct ice_rx_buf *rx_buf;
+		struct xdp_buff **xdp;
 		struct sk_buff *skb;
 		u16 stat_err_bits;
 		u16 vlan_tag = 0;
@@ -544,18 +560,18 @@
 		if (!size)
 			break;
 
-		rx_buf = &rx_ring->rx_buf[rx_ring->next_to_clean];
-		rx_buf->xdp->data_end = rx_buf->xdp->data + size;
-		xsk_buff_dma_sync_for_cpu(rx_buf->xdp, rx_ring->xsk_pool);
+		xdp = &rx_ring->xdp_buf[rx_ring->next_to_clean];
+		(*xdp)->data_end = (*xdp)->data + size;
+		xsk_buff_dma_sync_for_cpu(*xdp, rx_ring->xsk_pool);
 
-		xdp_res = ice_run_xdp_zc(rx_ring, rx_buf->xdp);
+		xdp_res = ice_run_xdp_zc(rx_ring, *xdp);
 		if (xdp_res) {
 			if (xdp_res & (ICE_XDP_TX | ICE_XDP_REDIR))
 				xdp_xmit |= xdp_res;
 			else
-				xsk_buff_free(rx_buf->xdp);
+				xsk_buff_free(*xdp);
 
-			rx_buf->xdp = NULL;
+			*xdp = NULL;
 			total_rx_bytes += size;
 			total_rx_packets++;
 			cleaned_count++;
@@ -565,7 +581,7 @@
 		}
 
 		/* XDP_PASS path */
-		skb = ice_construct_skb_zc(rx_ring, rx_buf);
+		skb = ice_construct_skb_zc(rx_ring, xdp);
 		if (!skb) {
 			rx_ring->rx_stats.alloc_buf_failed++;
 			break;
@@ -759,7 +775,7 @@
 	struct ice_vsi *vsi = np->vsi;
 	struct ice_ring *ring;
 
-	if (test_bit(ICE_DOWN, vsi->state))
+	if (test_bit(ICE_VSI_DOWN, vsi->state))
 		return -ENETDOWN;
 
 	if (!ice_is_xdp_ena_vsi(vsi))
@@ -810,15 +826,15 @@
  */
 void ice_xsk_clean_rx_ring(struct ice_ring *rx_ring)
 {
-	u16 i;
-
-	for (i = 0; i < rx_ring->count; i++) {
-		struct ice_rx_buf *rx_buf = &rx_ring->rx_buf[i];
+	u16 count_mask = rx_ring->count - 1;
+	u16 ntc = rx_ring->next_to_clean;
+	u16 ntu = rx_ring->next_to_use;
 
-		if (!rx_buf->xdp)
-			continue;
+	for ( ; ntc != ntu; ntc = (ntc + 1) & count_mask) {
+		struct xdp_buff **xdp = &rx_ring->xdp_buf[ntc];
 
-		rx_buf->xdp = NULL;
+		xsk_buff_free(*xdp);
+		*xdp = NULL;
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igb/e1000_mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igb/e1000_mac.c
@@ -426,7 +426,7 @@
 static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
 {
 	u32 hash_value, hash_mask;
-	u8 bit_shift = 0;
+	u8 bit_shift = 1;
 
 	/* Register count multiplied by bits per register */
 	hash_mask = (hw->mac.mta_reg_count * 32) - 1;
@@ -434,7 +434,7 @@
 	/* For a mc_filter_type of 0, bit_shift is the number of left-shifts
 	 * where 0xFF would still fall within the hash mask.
 	 */
-	while (hash_mask >> bit_shift != 0xFF)
+	while (hash_mask >> bit_shift != 0xFF && bit_shift < 4)
 		bit_shift++;
 
 	/* The portion of the address that is used for the hash table
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igb/igb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igb/igb.h
@@ -34,11 +34,11 @@
 /* TX/RX descriptor defines */
 #define IGB_DEFAULT_TXD		256
 #define IGB_DEFAULT_TX_WORK	128
-#define IGB_MIN_TXD		80
+#define IGB_MIN_TXD		64
 #define IGB_MAX_TXD		4096
 
 #define IGB_DEFAULT_RXD		256
-#define IGB_MIN_RXD		80
+#define IGB_MIN_RXD		64
 #define IGB_MAX_RXD		4096
 
 #define IGB_DEFAULT_ITR		3 /* dynamic */
@@ -664,6 +664,8 @@
 	struct igb_mac_addr *mac_table;
 	struct vf_mac_filter vf_macs;
 	struct vf_mac_filter *vf_mac_list;
+	/* lock for VF resources */
+	spinlock_t vfs_lock;
 };
 
 /* flags controlling PTP/1588 function */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -822,6 +822,8 @@
 		 */
 		ret_val = hw->nvm.ops.read(hw, last_word, 1,
 				   &eeprom_buff[last_word - first_word]);
+		if (ret_val)
+			goto out;
 	}
 
 	/* Device's eeprom is always little-endian, word addressable */
@@ -841,6 +843,7 @@
 		hw->nvm.ops.update(hw);
 
 	igb_set_fw_version(adapter);
+out:
 	kfree(eeprom_buff);
 	return ret_val;
 }
@@ -961,10 +964,6 @@
 			memcpy(&temp_ring[i], adapter->rx_ring[i],
 			       sizeof(struct igb_ring));
 
-			/* Clear copied XDP RX-queue info */
-			memset(&temp_ring[i].xdp_rxq, 0,
-			       sizeof(temp_ring[i].xdp_rxq));
-
 			temp_ring[i].count = new_rx_count;
 			err = igb_setup_rx_resources(&temp_ring[i]);
 			if (err) {
@@ -1413,6 +1412,8 @@
 			*data = 1;
 			return -1;
 		}
+		wr32(E1000_IVAR_MISC, E1000_IVAR_VALID << 8);
+		wr32(E1000_EIMS, BIT(0));
 	} else if (adapter->flags & IGB_FLAG_HAS_MSI) {
 		shared_int = false;
 		if (request_irq(irq,
@@ -2973,11 +2974,15 @@
 	if (err)
 		goto err_out_w_lock;
 
-	igb_update_ethtool_nfc_entry(adapter, input, input->sw_idx);
+	err = igb_update_ethtool_nfc_entry(adapter, input, input->sw_idx);
+	if (err)
+		goto err_out_input_filter;
 
 	spin_unlock(&adapter->nfc_lock);
 	return 0;
 
+err_out_input_filter:
+	igb_erase_filter(adapter, input);
 err_out_w_lock:
 	spin_unlock(&adapter->nfc_lock);
 err_out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igb/igb_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igb/igb_main.c
@@ -34,6 +34,7 @@
 #include <linux/bpf_trace.h>
 #include <linux/pm_runtime.h>
 #include <linux/etherdevice.h>
+#include <linux/lockdep.h>
 #ifdef CONFIG_IGB_DCA
 #include <linux/dca.h>
 #endif
@@ -666,6 +667,10 @@
 	dca_register_notify(&dca_notifier);
 #endif
 	ret = pci_register_driver(&igb_driver);
+#ifdef CONFIG_IGB_DCA
+	if (ret)
+		dca_unregister_notify(&dca_notifier);
+#endif
 	return ret;
 }
 
@@ -1204,8 +1209,12 @@
 	if (!q_vector) {
 		q_vector = kzalloc(size, GFP_KERNEL);
 	} else if (size > ksize(q_vector)) {
-		kfree_rcu(q_vector, rcu);
-		q_vector = kzalloc(size, GFP_KERNEL);
+		struct igb_q_vector *new_q_vector;
+
+		new_q_vector = kzalloc(size, GFP_KERNEL);
+		if (new_q_vector)
+			kfree_rcu(q_vector, rcu);
+		q_vector = new_q_vector;
 	} else {
 		memset(q_vector, 0, size);
 	}
@@ -2889,8 +2898,11 @@
 	}
 }
 
+/* This function assumes __netif_tx_lock is held by the caller. */
 static void igb_xdp_ring_update_tail(struct igb_ring *ring)
 {
+	lockdep_assert_held(&txring_txq(ring)->_xmit_lock);
+
 	/* Force memory writes to complete before letting h/w know there
 	 * are new descriptors to fetch.
 	 */
@@ -2975,11 +2987,11 @@
 		nxmit++;
 	}
 
-	__netif_tx_unlock(nq);
-
 	if (unlikely(flags & XDP_XMIT_FLUSH))
 		igb_xdp_ring_update_tail(tx_ring);
 
+	__netif_tx_unlock(nq);
+
 	return nxmit;
 }
 
@@ -3637,6 +3649,7 @@
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct igb_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	unsigned long flags;
 
 	/* reclaim resources allocated to VFs */
 	if (adapter->vf_data) {
@@ -3649,12 +3662,13 @@
 			pci_disable_sriov(pdev);
 			msleep(500);
 		}
-
+		spin_lock_irqsave(&adapter->vfs_lock, flags);
 		kfree(adapter->vf_mac_list);
 		adapter->vf_mac_list = NULL;
 		kfree(adapter->vf_data);
 		adapter->vf_data = NULL;
 		adapter->vfs_allocated_count = 0;
+		spin_unlock_irqrestore(&adapter->vfs_lock, flags);
 		wr32(E1000_IOVCTL, E1000_IOVCTL_REUSE_VFQ);
 		wrfl();
 		msleep(100);
@@ -3850,8 +3864,9 @@
 	struct pci_dev *pdev = adapter->pdev;
 	struct e1000_hw *hw = &adapter->hw;
 
-	/* Virtualization features not supported on i210 family. */
-	if ((hw->mac.type == e1000_i210) || (hw->mac.type == e1000_i211))
+	/* Virtualization features not supported on i210 and 82580 family. */
+	if ((hw->mac.type == e1000_i210) || (hw->mac.type == e1000_i211) ||
+	    (hw->mac.type == e1000_82580))
 		return;
 
 	/* Of the below we really only want the effect of getting
@@ -3974,6 +3989,9 @@
 
 	spin_lock_init(&adapter->nfc_lock);
 	spin_lock_init(&adapter->stats64_lock);
+
+	/* init spinlock to avoid concurrency of VF resources */
+	spin_lock_init(&adapter->vfs_lock);
 #ifdef CONFIG_PCI_IOV
 	switch (hw->mac.type) {
 	case e1000_82576:
@@ -4345,7 +4363,18 @@
 {
 	struct igb_adapter *adapter = netdev_priv(rx_ring->netdev);
 	struct device *dev = rx_ring->dev;
-	int size;
+	int size, res;
+
+	/* XDP RX-queue info */
+	if (xdp_rxq_info_is_reg(&rx_ring->xdp_rxq))
+		xdp_rxq_info_unreg(&rx_ring->xdp_rxq);
+	res = xdp_rxq_info_reg(&rx_ring->xdp_rxq, rx_ring->netdev,
+			       rx_ring->queue_index, 0);
+	if (res < 0) {
+		dev_err(dev, "Failed to register xdp_rxq index %u\n",
+			rx_ring->queue_index);
+		return res;
+	}
 
 	size = sizeof(struct igb_rx_buffer) * rx_ring->count;
 
@@ -4368,14 +4397,10 @@
 
 	rx_ring->xdp_prog = adapter->xdp_prog;
 
-	/* XDP RX-queue info */
-	if (xdp_rxq_info_reg(&rx_ring->xdp_rxq, rx_ring->netdev,
-			     rx_ring->queue_index, 0) < 0)
-		goto err;
-
 	return 0;
 
 err:
+	xdp_rxq_info_unreg(&rx_ring->xdp_rxq);
 	vfree(rx_ring->rx_buffer_info);
 	rx_ring->rx_buffer_info = NULL;
 	dev_err(dev, "Unable to allocate memory for the Rx descriptor ring\n");
@@ -4721,6 +4746,10 @@
 static void igb_set_rx_buffer_len(struct igb_adapter *adapter,
 				  struct igb_ring *rx_ring)
 {
+#if (PAGE_SIZE < 8192)
+	struct e1000_hw *hw = &adapter->hw;
+#endif
+
 	/* set build_skb and buffer size flags */
 	clear_ring_build_skb_enabled(rx_ring);
 	clear_ring_uses_large_buffer(rx_ring);
@@ -4731,10 +4760,9 @@
 	set_ring_build_skb_enabled(rx_ring);
 
 #if (PAGE_SIZE < 8192)
-	if (adapter->max_frame_size <= IGB_MAX_FRAME_BUILD_SKB)
-		return;
-
-	set_ring_uses_large_buffer(rx_ring);
+	if (adapter->max_frame_size > IGB_MAX_FRAME_BUILD_SKB ||
+	    rd32(E1000_RCTL) & E1000_RCTL_SBP)
+		set_ring_uses_large_buffer(rx_ring);
 #endif
 }
 
@@ -4812,8 +4840,11 @@
 	while (i != tx_ring->next_to_use) {
 		union e1000_adv_tx_desc *eop_desc, *tx_desc;
 
-		/* Free all the Tx ring sk_buffs */
-		dev_kfree_skb_any(tx_buffer->skb);
+		/* Free all the Tx ring sk_buffs or xdp frames */
+		if (tx_buffer->type == IGB_TYPE_SKB)
+			dev_kfree_skb_any(tx_buffer->skb);
+		else
+			xdp_return_frame(tx_buffer->xdpf);
 
 		/* unmap skb header data */
 		dma_unmap_single(tx_ring->dev,
@@ -5498,7 +5529,8 @@
 				break;
 			}
 
-			if (adapter->link_speed != SPEED_1000)
+			if (adapter->link_speed != SPEED_1000 ||
+			    !hw->phy.ops.read_reg)
 				goto no_wait;
 
 			/* wait for Remote receiver status OK */
@@ -6732,77 +6764,85 @@
 	}
 }
 
+static void igb_perout(struct igb_adapter *adapter, int tsintr_tt)
+{
+	int pin = ptp_find_pin(adapter->ptp_clock, PTP_PF_PEROUT, tsintr_tt);
+	struct e1000_hw *hw = &adapter->hw;
+	struct timespec64 ts;
+	u32 tsauxc;
+
+	if (pin < 0 || pin >= IGB_N_PEROUT)
+		return;
+
+	spin_lock(&adapter->tmreg_lock);
+	ts = timespec64_add(adapter->perout[pin].start,
+			    adapter->perout[pin].period);
+	/* u32 conversion of tv_sec is safe until y2106 */
+	wr32((tsintr_tt == 1) ? E1000_TRGTTIML1 : E1000_TRGTTIML0, ts.tv_nsec);
+	wr32((tsintr_tt == 1) ? E1000_TRGTTIMH1 : E1000_TRGTTIMH0, (u32)ts.tv_sec);
+	tsauxc = rd32(E1000_TSAUXC);
+	tsauxc |= TSAUXC_EN_TT0;
+	wr32(E1000_TSAUXC, tsauxc);
+	adapter->perout[pin].start = ts;
+	spin_unlock(&adapter->tmreg_lock);
+}
+
+static void igb_extts(struct igb_adapter *adapter, int tsintr_tt)
+{
+	int pin = ptp_find_pin(adapter->ptp_clock, PTP_PF_EXTTS, tsintr_tt);
+	struct e1000_hw *hw = &adapter->hw;
+	struct ptp_clock_event event;
+	u32 sec, nsec;
+
+	if (pin < 0 || pin >= IGB_N_EXTTS)
+		return;
+
+	nsec = rd32((tsintr_tt == 1) ? E1000_AUXSTMPL1 : E1000_AUXSTMPL0);
+	sec  = rd32((tsintr_tt == 1) ? E1000_AUXSTMPH1 : E1000_AUXSTMPH0);
+	event.type = PTP_CLOCK_EXTTS;
+	event.index = tsintr_tt;
+	event.timestamp = sec * 1000000000ULL + nsec;
+	ptp_clock_event(adapter->ptp_clock, &event);
+}
+
 static void igb_tsync_interrupt(struct igb_adapter *adapter)
 {
+	const u32 mask = (TSINTR_SYS_WRAP | E1000_TSICR_TXTS |
+			  TSINTR_TT0 | TSINTR_TT1 |
+			  TSINTR_AUTT0 | TSINTR_AUTT1);
 	struct e1000_hw *hw = &adapter->hw;
+	u32 tsicr = rd32(E1000_TSICR);
 	struct ptp_clock_event event;
-	struct timespec64 ts;
-	u32 ack = 0, tsauxc, sec, nsec, tsicr = rd32(E1000_TSICR);
+
+	if (hw->mac.type == e1000_82580) {
+		/* 82580 has a hardware bug that requires an explicit
+		 * write to clear the TimeSync interrupt cause.
+		 */
+		wr32(E1000_TSICR, tsicr & mask);
+	}
 
 	if (tsicr & TSINTR_SYS_WRAP) {
 		event.type = PTP_CLOCK_PPS;
 		if (adapter->ptp_caps.pps)
 			ptp_clock_event(adapter->ptp_clock, &event);
-		ack |= TSINTR_SYS_WRAP;
 	}
 
 	if (tsicr & E1000_TSICR_TXTS) {
 		/* retrieve hardware timestamp */
 		schedule_work(&adapter->ptp_tx_work);
-		ack |= E1000_TSICR_TXTS;
 	}
 
-	if (tsicr & TSINTR_TT0) {
-		spin_lock(&adapter->tmreg_lock);
-		ts = timespec64_add(adapter->perout[0].start,
-				    adapter->perout[0].period);
-		/* u32 conversion of tv_sec is safe until y2106 */
-		wr32(E1000_TRGTTIML0, ts.tv_nsec);
-		wr32(E1000_TRGTTIMH0, (u32)ts.tv_sec);
-		tsauxc = rd32(E1000_TSAUXC);
-		tsauxc |= TSAUXC_EN_TT0;
-		wr32(E1000_TSAUXC, tsauxc);
-		adapter->perout[0].start = ts;
-		spin_unlock(&adapter->tmreg_lock);
-		ack |= TSINTR_TT0;
-	}
-
-	if (tsicr & TSINTR_TT1) {
-		spin_lock(&adapter->tmreg_lock);
-		ts = timespec64_add(adapter->perout[1].start,
-				    adapter->perout[1].period);
-		wr32(E1000_TRGTTIML1, ts.tv_nsec);
-		wr32(E1000_TRGTTIMH1, (u32)ts.tv_sec);
-		tsauxc = rd32(E1000_TSAUXC);
-		tsauxc |= TSAUXC_EN_TT1;
-		wr32(E1000_TSAUXC, tsauxc);
-		adapter->perout[1].start = ts;
-		spin_unlock(&adapter->tmreg_lock);
-		ack |= TSINTR_TT1;
-	}
-
-	if (tsicr & TSINTR_AUTT0) {
-		nsec = rd32(E1000_AUXSTMPL0);
-		sec  = rd32(E1000_AUXSTMPH0);
-		event.type = PTP_CLOCK_EXTTS;
-		event.index = 0;
-		event.timestamp = sec * 1000000000ULL + nsec;
-		ptp_clock_event(adapter->ptp_clock, &event);
-		ack |= TSINTR_AUTT0;
-	}
-
-	if (tsicr & TSINTR_AUTT1) {
-		nsec = rd32(E1000_AUXSTMPL1);
-		sec  = rd32(E1000_AUXSTMPH1);
-		event.type = PTP_CLOCK_EXTTS;
-		event.index = 1;
-		event.timestamp = sec * 1000000000ULL + nsec;
-		ptp_clock_event(adapter->ptp_clock, &event);
-		ack |= TSINTR_AUTT1;
-	}
+	if (tsicr & TSINTR_TT0)
+		igb_perout(adapter, 0);
+
+	if (tsicr & TSINTR_TT1)
+		igb_perout(adapter, 1);
+
+	if (tsicr & TSINTR_AUTT0)
+		igb_extts(adapter, 0);
 
-	/* acknowledge the interrupts */
-	wr32(E1000_TSICR, ack);
+	if (tsicr & TSINTR_AUTT1)
+		igb_extts(adapter, 1);
 }
 
 static irqreturn_t igb_msix_other(int irq, void *data)
@@ -7392,7 +7432,7 @@
 {
 	struct e1000_hw *hw = &adapter->hw;
 	unsigned char *vf_mac = adapter->vf_data[vf].vf_mac_addresses;
-	u32 reg, msgbuf[3];
+	u32 reg, msgbuf[3] = {};
 	u8 *addr = (u8 *)(&msgbuf[1]);
 
 	/* process all the same items cleared in a function level reset */
@@ -7641,6 +7681,20 @@
 	struct vf_mac_filter *entry = NULL;
 	int ret = 0;
 
+	if ((vf_data->flags & IGB_VF_FLAG_PF_SET_MAC) &&
+	    !vf_data->trusted) {
+		dev_warn(&pdev->dev,
+			 "VF %d requested MAC filter but is administratively denied\n",
+			  vf);
+		return -EINVAL;
+	}
+	if (!is_valid_ether_addr(addr)) {
+		dev_warn(&pdev->dev,
+			 "VF %d attempted to set invalid MAC filter\n",
+			  vf);
+		return -EINVAL;
+	}
+
 	switch (info) {
 	case E1000_VF_MAC_FILTER_CLR:
 		/* remove all unicast MAC filters related to the current VF */
@@ -7654,20 +7708,6 @@
 		}
 		break;
 	case E1000_VF_MAC_FILTER_ADD:
-		if ((vf_data->flags & IGB_VF_FLAG_PF_SET_MAC) &&
-		    !vf_data->trusted) {
-			dev_warn(&pdev->dev,
-				 "VF %d requested MAC filter but is administratively denied\n",
-				 vf);
-			return -EINVAL;
-		}
-		if (!is_valid_ether_addr(addr)) {
-			dev_warn(&pdev->dev,
-				 "VF %d attempted to set invalid MAC filter\n",
-				 vf);
-			return -EINVAL;
-		}
-
 		/* try to find empty slot in the list */
 		list_for_each(pos, &adapter->vf_macs.l) {
 			entry = list_entry(pos, struct vf_mac_filter, l);
@@ -7835,8 +7875,10 @@
 static void igb_msg_task(struct igb_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
+	unsigned long flags;
 	u32 vf;
 
+	spin_lock_irqsave(&adapter->vfs_lock, flags);
 	for (vf = 0; vf < adapter->vfs_allocated_count; vf++) {
 		/* process any reset requests */
 		if (!igb_check_for_rst(hw, vf))
@@ -7850,6 +7892,7 @@
 		if (!igb_check_for_ack(hw, vf))
 			igb_rcv_ack_from_vf(adapter, vf);
 	}
+	spin_unlock_irqrestore(&adapter->vfs_lock, flags);
 }
 
 /**
@@ -8019,7 +8062,7 @@
 	if (likely(napi_complete_done(napi, work_done)))
 		igb_ring_irq_enable(q_vector);
 
-	return min(work_done, budget - 1);
+	return work_done;
 }
 
 /**
@@ -8668,12 +8711,14 @@
 
 static int igb_clean_rx_irq(struct igb_q_vector *q_vector, const int budget)
 {
+	unsigned int total_bytes = 0, total_packets = 0;
 	struct igb_adapter *adapter = q_vector->adapter;
 	struct igb_ring *rx_ring = q_vector->rx.ring;
-	struct sk_buff *skb = rx_ring->skb;
-	unsigned int total_bytes = 0, total_packets = 0;
 	u16 cleaned_count = igb_desc_unused(rx_ring);
+	struct sk_buff *skb = rx_ring->skb;
+	int cpu = smp_processor_id();
 	unsigned int xdp_xmit = 0;
+	struct netdev_queue *nq;
 	struct xdp_buff xdp;
 	u32 frame_sz = 0;
 	int rx_buf_pgcnt;
@@ -8800,7 +8845,10 @@
 	if (xdp_xmit & IGB_XDP_TX) {
 		struct igb_ring *tx_ring = igb_xdp_tx_queue_mapping(adapter);
 
+		nq = txring_txq(tx_ring);
+		__netif_tx_lock(nq, cpu);
 		igb_xdp_ring_update_tail(tx_ring);
+		__netif_tx_unlock(nq);
 	}
 
 	u64_stats_update_begin(&rx_ring->rx_syncp);
@@ -9247,7 +9295,7 @@
 	return __igb_shutdown(to_pci_dev(dev), NULL, 0);
 }
 
-static int __maybe_unused igb_resume(struct device *dev)
+static int __maybe_unused __igb_resume(struct device *dev, bool rpm)
 {
 	struct pci_dev *pdev = to_pci_dev(dev);
 	struct net_device *netdev = pci_get_drvdata(pdev);
@@ -9290,17 +9338,24 @@
 
 	wr32(E1000_WUS, ~0);
 
-	rtnl_lock();
+	if (!rpm)
+		rtnl_lock();
 	if (!err && netif_running(netdev))
 		err = __igb_open(netdev, true);
 
 	if (!err)
 		netif_device_attach(netdev);
-	rtnl_unlock();
+	if (!rpm)
+		rtnl_unlock();
 
 	return err;
 }
 
+static int __maybe_unused igb_resume(struct device *dev)
+{
+	return __igb_resume(dev, false);
+}
+
 static int __maybe_unused igb_runtime_idle(struct device *dev)
 {
 	struct net_device *netdev = dev_get_drvdata(dev);
@@ -9319,7 +9374,7 @@
 
 static int __maybe_unused igb_runtime_resume(struct device *dev)
 {
-	return igb_resume(dev);
+	return __igb_resume(dev, true);
 }
 
 static void igb_shutdown(struct pci_dev *pdev)
@@ -9417,6 +9472,11 @@
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct igb_adapter *adapter = netdev_priv(netdev);
 
+	if (state == pci_channel_io_normal) {
+		dev_warn(&pdev->dev, "Non-correctable non-fatal error reported.\n");
+		return PCI_ERS_RESULT_CAN_RECOVER;
+	}
+
 	netif_device_detach(netdev);
 
 	if (state == pci_channel_io_perm_failure)
@@ -9435,7 +9495,7 @@
  *  @pdev: Pointer to PCI device
  *
  *  Restart the card from scratch, as if from a cold-boot. Implementation
- *  resembles the first-half of the igb_resume routine.
+ *  resembles the first-half of the __igb_resume routine.
  **/
 static pci_ers_result_t igb_io_slot_reset(struct pci_dev *pdev)
 {
@@ -9475,7 +9535,7 @@
  *
  *  This callback is called when the error recovery driver tells us that
  *  its OK to resume normal operation. Implementation resembles the
- *  second-half of the igb_resume routine.
+ *  second-half of the __igb_resume routine.
  */
 static void igb_io_resume(struct pci_dev *pdev)
 {
@@ -9483,6 +9543,10 @@
 	struct igb_adapter *adapter = netdev_priv(netdev);
 
 	if (netif_running(netdev)) {
+		if (!test_bit(__IGB_DOWN, &adapter->state)) {
+			dev_dbg(&pdev->dev, "Resuming from non-fatal error, do nothing.\n");
+			return;
+		}
 		if (igb_up(adapter)) {
 			dev_err(&pdev->dev, "igb_up failed after reset\n");
 			return;
@@ -9805,11 +9869,10 @@
 	struct e1000_hw *hw = &adapter->hw;
 	u32 dmac_thr;
 	u16 hwm;
+	u32 reg;
 
 	if (hw->mac.type > e1000_82580) {
 		if (adapter->flags & IGB_FLAG_DMAC) {
-			u32 reg;
-
 			/* force threshold to 0. */
 			wr32(E1000_DMCTXTH, 0);
 
@@ -9842,7 +9905,6 @@
 			/* Disable BMC-to-OS Watchdog Enable */
 			if (hw->mac.type != e1000_i354)
 				reg &= ~E1000_DMACR_DC_BMC2OSW_EN;
-
 			wr32(E1000_DMACR, reg);
 
 			/* no lower threshold to disable
@@ -9859,12 +9921,12 @@
 			 */
 			wr32(E1000_DMCTXTH, (IGB_MIN_TXPBSIZE -
 			     (IGB_TX_BUF_4096 + adapter->max_frame_size)) >> 6);
+		}
 
-			/* make low power state decision controlled
-			 * by DMA coal
-			 */
+		if (hw->mac.type >= e1000_i210 ||
+		    (adapter->flags & IGB_FLAG_DMAC)) {
 			reg = rd32(E1000_PCIEMISC);
-			reg &= ~E1000_PCIEMISC_LX_DECISION;
+			reg |= E1000_PCIEMISC_LX_DECISION;
 			wr32(E1000_PCIEMISC, reg);
 		} /* endif adapter->dmac is not disabled */
 	} else if (hw->mac.type == e1000_82580) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igb/igb_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igb/igb_ptp.c
@@ -826,7 +826,7 @@
 
 	igb_ptp_systim_to_hwtstamp(adapter, &shhwtstamps, regval);
 	/* adjust timestamp for the TX latency based on link speed */
-	if (adapter->hw.mac.type == e1000_i210) {
+	if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
 		switch (adapter->link_speed) {
 		case SPEED_10:
 			adjust = IGB_I210_TX_LATENCY_10;
@@ -872,6 +872,7 @@
 			ktime_t *timestamp)
 {
 	struct igb_adapter *adapter = q_vector->adapter;
+	struct e1000_hw *hw = &adapter->hw;
 	struct skb_shared_hwtstamps ts;
 	__le64 *regval = (__le64 *)va;
 	int adjust = 0;
@@ -891,7 +892,7 @@
 	igb_ptp_systim_to_hwtstamp(adapter, &ts, le64_to_cpu(regval[1]));
 
 	/* adjust timestamp for the RX latency based on link speed */
-	if (adapter->hw.mac.type == e1000_i210) {
+	if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
 		switch (adapter->link_speed) {
 		case SPEED_10:
 			adjust = IGB_I210_RX_LATENCY_10;
@@ -1260,18 +1261,6 @@
 		return;
 	}
 
-	spin_lock_init(&adapter->tmreg_lock);
-	INIT_WORK(&adapter->ptp_tx_work, igb_ptp_tx_work);
-
-	if (adapter->ptp_flags & IGB_PTP_OVERFLOW_CHECK)
-		INIT_DELAYED_WORK(&adapter->ptp_overflow_work,
-				  igb_ptp_overflow_check);
-
-	adapter->tstamp_config.rx_filter = HWTSTAMP_FILTER_NONE;
-	adapter->tstamp_config.tx_type = HWTSTAMP_TX_OFF;
-
-	igb_ptp_reset(adapter);
-
 	adapter->ptp_clock = ptp_clock_register(&adapter->ptp_caps,
 						&adapter->pdev->dev);
 	if (IS_ERR(adapter->ptp_clock)) {
@@ -1281,6 +1270,18 @@
 		dev_info(&adapter->pdev->dev, "added PHC on %s\n",
 			 adapter->netdev->name);
 		adapter->ptp_flags |= IGB_PTP_ENABLED;
+
+		spin_lock_init(&adapter->tmreg_lock);
+		INIT_WORK(&adapter->ptp_tx_work, igb_ptp_tx_work);
+
+		if (adapter->ptp_flags & IGB_PTP_OVERFLOW_CHECK)
+			INIT_DELAYED_WORK(&adapter->ptp_overflow_work,
+					  igb_ptp_overflow_check);
+
+		adapter->tstamp_config.rx_filter = HWTSTAMP_FILTER_NONE;
+		adapter->tstamp_config.tx_type = HWTSTAMP_TX_OFF;
+
+		igb_ptp_reset(adapter);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igbvf/igbvf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igbvf/igbvf.h
@@ -39,11 +39,11 @@
 /* Tx/Rx descriptor defines */
 #define IGBVF_DEFAULT_TXD	256
 #define IGBVF_MAX_TXD		4096
-#define IGBVF_MIN_TXD		80
+#define IGBVF_MIN_TXD		64
 
 #define IGBVF_DEFAULT_RXD	256
 #define IGBVF_MAX_RXD		4096
-#define IGBVF_MIN_RXD		80
+#define IGBVF_MIN_RXD		64
 
 #define IGBVF_MIN_ITR_USECS	10 /* 100000 irq/sec */
 #define IGBVF_MAX_ITR_USECS	10000 /* 100    irq/sec */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igbvf/netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igbvf/netdev.c
@@ -1074,7 +1074,7 @@
 			  igbvf_intr_msix_rx, 0, adapter->rx_ring->name,
 			  netdev);
 	if (err)
-		goto out;
+		goto free_irq_tx;
 
 	adapter->rx_ring->itr_register = E1000_EITR(vector);
 	adapter->rx_ring->itr_val = adapter->current_itr;
@@ -1083,10 +1083,14 @@
 	err = request_irq(adapter->msix_entries[vector].vector,
 			  igbvf_msix_other, 0, netdev->name, netdev);
 	if (err)
-		goto out;
+		goto free_irq_rx;
 
 	igbvf_configure_msix(adapter);
 	return 0;
+free_irq_rx:
+	free_irq(adapter->msix_entries[--vector].vector, netdev);
+free_irq_tx:
+	free_irq(adapter->msix_entries[--vector].vector, netdev);
 out:
 	return err;
 }
@@ -2861,6 +2865,7 @@
 	return 0;
 
 err_hw_init:
+	netif_napi_del(&adapter->rx_ring->napi);
 	kfree(adapter->tx_ring);
 	kfree(adapter->rx_ring);
 err_sw_init:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igbvf/vf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igbvf/vf.c
@@ -1,6 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
 /* Copyright(c) 2009 - 2018 Intel Corporation. */
 
+#include <linux/etherdevice.h>
+
 #include "vf.h"
 
 static s32 e1000_check_for_link_vf(struct e1000_hw *hw);
@@ -131,11 +133,16 @@
 		/* set our "perm_addr" based on info provided by PF */
 		ret_val = mbx->ops.read_posted(hw, msgbuf, 3);
 		if (!ret_val) {
-			if (msgbuf[0] == (E1000_VF_RESET |
-					  E1000_VT_MSGTYPE_ACK))
+			switch (msgbuf[0]) {
+			case E1000_VF_RESET | E1000_VT_MSGTYPE_ACK:
 				memcpy(hw->mac.perm_addr, addr, ETH_ALEN);
-			else
+				break;
+			case E1000_VF_RESET | E1000_VT_MSGTYPE_NACK:
+				eth_zero_addr(hw->mac.perm_addr);
+				break;
+			default:
 				ret_val = -E1000_ERR_MAC_INIT;
+			}
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc.h
@@ -13,6 +13,7 @@
 #include <linux/ptp_clock_kernel.h>
 #include <linux/timecounter.h>
 #include <linux/net_tstamp.h>
+#include <linux/bitfield.h>
 
 #include "igc_hw.h"
 
@@ -94,6 +95,8 @@
 	u8 queue_index;                 /* logical index of the ring*/
 	u8 reg_idx;                     /* physical index of the ring */
 	bool launchtime_enable;         /* true if LaunchTime is enabled */
+	ktime_t last_tx_cycle;          /* end of the cycle with a launchtime transmission */
+	ktime_t last_ff_cycle;          /* Last cycle with an active first flag */
 
 	u32 start_time;
 	u32 end_time;
@@ -182,6 +185,7 @@
 
 	ktime_t base_time;
 	ktime_t cycle_time;
+	bool qbv_enable;
 
 	/* OS defined structs */
 	struct pci_dev *pdev;
@@ -224,6 +228,10 @@
 	struct ptp_clock *ptp_clock;
 	struct ptp_clock_info ptp_caps;
 	struct work_struct ptp_tx_work;
+	/* Access to ptp_tx_skb and ptp_tx_start are protected by the
+	 * ptp_tx_lock.
+	 */
+	spinlock_t ptp_tx_lock;
 	struct sk_buff *ptp_tx_skb;
 	struct hwtstamp_config tstamp_config;
 	unsigned long ptp_tx_start;
@@ -309,6 +317,33 @@
 #define IGC_MRQC_RSS_FIELD_IPV4_UDP	0x00400000
 #define IGC_MRQC_RSS_FIELD_IPV6_UDP	0x00800000
 
+/* RX-desc Write-Back format RSS Type's */
+enum igc_rss_type_num {
+	IGC_RSS_TYPE_NO_HASH		= 0,
+	IGC_RSS_TYPE_HASH_TCP_IPV4	= 1,
+	IGC_RSS_TYPE_HASH_IPV4		= 2,
+	IGC_RSS_TYPE_HASH_TCP_IPV6	= 3,
+	IGC_RSS_TYPE_HASH_IPV6_EX	= 4,
+	IGC_RSS_TYPE_HASH_IPV6		= 5,
+	IGC_RSS_TYPE_HASH_TCP_IPV6_EX	= 6,
+	IGC_RSS_TYPE_HASH_UDP_IPV4	= 7,
+	IGC_RSS_TYPE_HASH_UDP_IPV6	= 8,
+	IGC_RSS_TYPE_HASH_UDP_IPV6_EX	= 9,
+	IGC_RSS_TYPE_MAX		= 10,
+};
+#define IGC_RSS_TYPE_MAX_TABLE		16
+#define IGC_RSS_TYPE_MASK		GENMASK(3,0) /* 4-bits (3:0) = mask 0x0F */
+
+/* igc_rss_type - Rx descriptor RSS type field */
+static inline u32 igc_rss_type(const union igc_adv_rx_desc *rx_desc)
+{
+	/* RSS Type 4-bits (3:0) number: 0-9 (above 9 is reserved)
+	 * Accessing the same bits via u16 (wb.lower.lo_dword.hs_rss.pkt_info)
+	 * is slightly slower than via u32 (wb.lower.lo_dword.data)
+	 */
+	return le32_get_bits(rx_desc->wb.lower.lo_dword.data, IGC_RSS_TYPE_MASK);
+}
+
 /* Interrupt defines */
 #define IGC_START_ITR			648 /* ~6000 ints/sec */
 #define IGC_4K_ITR			980
@@ -324,11 +359,11 @@
 /* TX/RX descriptor defines */
 #define IGC_DEFAULT_TXD		256
 #define IGC_DEFAULT_TX_WORK	128
-#define IGC_MIN_TXD		80
+#define IGC_MIN_TXD		64
 #define IGC_MAX_TXD		4096
 
 #define IGC_DEFAULT_RXD		256
-#define IGC_MIN_RXD		80
+#define IGC_MIN_RXD		64
 #define IGC_MAX_RXD		4096
 
 /* Supported Rx Buffer Sizes */
@@ -399,7 +434,6 @@
 	__IGC_TESTING,
 	__IGC_RESETTING,
 	__IGC_DOWN,
-	__IGC_PTP_TX_IN_PROGRESS,
 };
 
 enum igc_tx_flags {
@@ -503,6 +537,7 @@
 	u16 etype;
 	__be16 vlan_etype;
 	u16 vlan_tci;
+	u16 vlan_tci_mask;
 	u8 src_addr[ETH_ALEN];
 	u8 dst_addr[ETH_ALEN];
 	u8 user_data[8];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_base.c
@@ -402,6 +402,35 @@
 	rd32(IGC_MPC);
 }
 
+bool igc_is_device_id_i225(struct igc_hw *hw)
+{
+	switch (hw->device_id) {
+	case IGC_DEV_ID_I225_LM:
+	case IGC_DEV_ID_I225_V:
+	case IGC_DEV_ID_I225_I:
+	case IGC_DEV_ID_I225_K:
+	case IGC_DEV_ID_I225_K2:
+	case IGC_DEV_ID_I225_LMVP:
+	case IGC_DEV_ID_I225_IT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+bool igc_is_device_id_i226(struct igc_hw *hw)
+{
+	switch (hw->device_id) {
+	case IGC_DEV_ID_I226_LM:
+	case IGC_DEV_ID_I226_V:
+	case IGC_DEV_ID_I226_K:
+	case IGC_DEV_ID_I226_IT:
+		return true;
+	default:
+		return false;
+	}
+}
+
 static struct igc_mac_operations igc_mac_ops_base = {
 	.init_hw		= igc_init_hw_base,
 	.check_for_link		= igc_check_for_copper_link,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_base.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_base.h
@@ -7,6 +7,8 @@
 /* forward declaration */
 void igc_rx_fifo_flush_base(struct igc_hw *hw);
 void igc_power_down_phy_copper_base(struct igc_hw *hw);
+bool igc_is_device_id_i225(struct igc_hw *hw);
+bool igc_is_device_id_i226(struct igc_hw *hw);
 
 /* Transmit Descriptor - Advanced */
 union igc_adv_tx_desc {
@@ -85,8 +87,13 @@
 #define IGC_RXDCTL_SWFLUSH		0x04000000 /* Receive Software Flush */
 
 /* SRRCTL bit definitions */
-#define IGC_SRRCTL_BSIZEPKT_SHIFT		10 /* Shift _right_ */
-#define IGC_SRRCTL_BSIZEHDRSIZE_SHIFT		2  /* Shift _left_ */
-#define IGC_SRRCTL_DESCTYPE_ADV_ONEBUF	0x02000000
+#define IGC_SRRCTL_BSIZEPKT_MASK	GENMASK(6, 0)
+#define IGC_SRRCTL_BSIZEPKT(x)		FIELD_PREP(IGC_SRRCTL_BSIZEPKT_MASK, \
+					(x) / 1024) /* in 1 KB resolution */
+#define IGC_SRRCTL_BSIZEHDR_MASK	GENMASK(13, 8)
+#define IGC_SRRCTL_BSIZEHDR(x)		FIELD_PREP(IGC_SRRCTL_BSIZEHDR_MASK, \
+					(x) / 64) /* in 64 bytes resolution */
+#define IGC_SRRCTL_DESCTYPE_MASK	GENMASK(27, 25)
+#define IGC_SRRCTL_DESCTYPE_ADV_ONEBUF	FIELD_PREP(IGC_SRRCTL_DESCTYPE_MASK, 1)
 
 #endif /* _IGC_BASE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_defines.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_defines.h
@@ -324,6 +324,8 @@
 #define IGC_ADVTXD_L4LEN_SHIFT	8  /* Adv ctxt L4LEN shift */
 #define IGC_ADVTXD_MSS_SHIFT	16 /* Adv ctxt MSS shift */
 
+#define IGC_ADVTXD_TSN_CNTX_FIRST	0x00000080
+
 /* Transmit Control */
 #define IGC_TCTL_EN		0x00000002 /* enable Tx */
 #define IGC_TCTL_PSP		0x00000008 /* pad short packets */
@@ -403,6 +405,21 @@
 #define IGC_DTXMXPKTSZ_TSN	0x19 /* 1600 bytes of max TX DMA packet size */
 #define IGC_DTXMXPKTSZ_DEFAULT	0x98 /* 9728-byte Jumbo frames */
 
+/* Retry Buffer Control */
+#define IGC_RETX_CTL			0x041C
+#define IGC_RETX_CTL_WATERMARK_MASK	0xF
+#define IGC_RETX_CTL_QBVFULLTH_SHIFT	8 /* QBV Retry Buffer Full Threshold */
+#define IGC_RETX_CTL_QBVFULLEN	0x1000 /* Enable QBV Retry Buffer Full Threshold */
+
+/* Transmit Scheduling Latency */
+/* Latency between transmission scheduling (LaunchTime) and the time
+ * the packet is transmitted to the network in nanosecond.
+ */
+#define IGC_TXOFFSET_SPEED_10	0x000034BC
+#define IGC_TXOFFSET_SPEED_100	0x00000578
+#define IGC_TXOFFSET_SPEED_1000	0x0000012C
+#define IGC_TXOFFSET_SPEED_2500	0x00000578
+
 /* Time Sync Interrupt Causes */
 #define IGC_TSICR_SYS_WRAP	BIT(0) /* SYSTIM Wrap around. */
 #define IGC_TSICR_TXTS		BIT(1) /* Transmit Timestamp. */
@@ -467,7 +484,9 @@
 #define IGC_TSAUXC_EN_TT0	BIT(0)  /* Enable target time 0. */
 #define IGC_TSAUXC_EN_TT1	BIT(1)  /* Enable target time 1. */
 #define IGC_TSAUXC_EN_CLK0	BIT(2)  /* Enable Configurable Frequency Clock 0. */
+#define IGC_TSAUXC_ST0		BIT(4)  /* Start Clock 0 Toggle on Target Time 0. */
 #define IGC_TSAUXC_EN_CLK1	BIT(5)  /* Enable Configurable Frequency Clock 1. */
+#define IGC_TSAUXC_ST1		BIT(7)  /* Start Clock 1 Toggle on Target Time 1. */
 #define IGC_TSAUXC_EN_TS0	BIT(8)  /* Enable hardware timestamp 0. */
 #define IGC_TSAUXC_AUTT0	BIT(9)  /* Auxiliary Timestamp Taken. */
 #define IGC_TSAUXC_EN_TS1	BIT(10) /* Enable hardware timestamp 0. */
@@ -514,6 +533,7 @@
 /* Transmit Scheduling */
 #define IGC_TQAVCTRL_TRANSMIT_MODE_TSN	0x00000001
 #define IGC_TQAVCTRL_ENHANCED_QAV	0x00000008
+#define IGC_TQAVCTRL_FUTSCDDIS		0x00000080
 
 #define IGC_TXQCTL_QUEUE_MODE_LAUNCHT	0x00000001
 #define IGC_TXQCTL_STRICT_CYCLE		0x00000002
@@ -535,7 +555,7 @@
 #define IGC_PTM_CTRL_START_NOW	BIT(29) /* Start PTM Now */
 #define IGC_PTM_CTRL_EN		BIT(30) /* Enable PTM */
 #define IGC_PTM_CTRL_TRIG	BIT(31) /* PTM Cycle trigger */
-#define IGC_PTM_CTRL_SHRT_CYC(usec)	(((usec) & 0x2f) << 2)
+#define IGC_PTM_CTRL_SHRT_CYC(usec)	(((usec) & 0x3f) << 2)
 #define IGC_PTM_CTRL_PTM_TO(usec)	(((usec) & 0xff) << 8)
 
 #define IGC_PTM_SHORT_CYC_DEFAULT	10  /* Default Short/interrupted cycle interval */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_ethtool.c
@@ -861,6 +861,18 @@
 	spin_unlock(&adapter->stats64_lock);
 }
 
+static int igc_ethtool_get_previous_rx_coalesce(struct igc_adapter *adapter)
+{
+	return (adapter->rx_itr_setting <= 3) ?
+		adapter->rx_itr_setting : adapter->rx_itr_setting >> 2;
+}
+
+static int igc_ethtool_get_previous_tx_coalesce(struct igc_adapter *adapter)
+{
+	return (adapter->tx_itr_setting <= 3) ?
+		adapter->tx_itr_setting : adapter->tx_itr_setting >> 2;
+}
+
 static int igc_ethtool_get_coalesce(struct net_device *netdev,
 				    struct ethtool_coalesce *ec,
 				    struct kernel_ethtool_coalesce *kernel_coal,
@@ -868,17 +880,8 @@
 {
 	struct igc_adapter *adapter = netdev_priv(netdev);
 
-	if (adapter->rx_itr_setting <= 3)
-		ec->rx_coalesce_usecs = adapter->rx_itr_setting;
-	else
-		ec->rx_coalesce_usecs = adapter->rx_itr_setting >> 2;
-
-	if (!(adapter->flags & IGC_FLAG_QUEUE_PAIRS)) {
-		if (adapter->tx_itr_setting <= 3)
-			ec->tx_coalesce_usecs = adapter->tx_itr_setting;
-		else
-			ec->tx_coalesce_usecs = adapter->tx_itr_setting >> 2;
-	}
+	ec->rx_coalesce_usecs = igc_ethtool_get_previous_rx_coalesce(adapter);
+	ec->tx_coalesce_usecs = igc_ethtool_get_previous_tx_coalesce(adapter);
 
 	return 0;
 }
@@ -903,8 +906,12 @@
 	    ec->tx_coalesce_usecs == 2)
 		return -EINVAL;
 
-	if ((adapter->flags & IGC_FLAG_QUEUE_PAIRS) && ec->tx_coalesce_usecs)
+	if ((adapter->flags & IGC_FLAG_QUEUE_PAIRS) &&
+	    ec->tx_coalesce_usecs != igc_ethtool_get_previous_tx_coalesce(adapter)) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Queue Pair mode enabled, both Rx and Tx coalescing controlled by rx-usecs");
 		return -EINVAL;
+	}
 
 	/* If ITR is disabled, disable DMAC */
 	if (ec->rx_coalesce_usecs == 0) {
@@ -943,6 +950,7 @@
 }
 
 #define ETHER_TYPE_FULL_MASK ((__force __be16)~0)
+#define VLAN_TCI_FULL_MASK ((__force __be16)~0)
 static int igc_ethtool_get_nfc_rule(struct igc_adapter *adapter,
 				    struct ethtool_rxnfc *cmd)
 {
@@ -965,10 +973,16 @@
 		fsp->m_u.ether_spec.h_proto = ETHER_TYPE_FULL_MASK;
 	}
 
+	if (rule->filter.match_flags & IGC_FILTER_FLAG_VLAN_ETYPE) {
+		fsp->flow_type |= FLOW_EXT;
+		fsp->h_ext.vlan_etype = rule->filter.vlan_etype;
+		fsp->m_ext.vlan_etype = ETHER_TYPE_FULL_MASK;
+	}
+
 	if (rule->filter.match_flags & IGC_FILTER_FLAG_VLAN_TCI) {
 		fsp->flow_type |= FLOW_EXT;
 		fsp->h_ext.vlan_tci = htons(rule->filter.vlan_tci);
-		fsp->m_ext.vlan_tci = htons(VLAN_PRIO_MASK);
+		fsp->m_ext.vlan_tci = htons(rule->filter.vlan_tci_mask);
 	}
 
 	if (rule->filter.match_flags & IGC_FILTER_FLAG_DST_MAC_ADDR) {
@@ -1203,6 +1217,7 @@
 
 	if ((fsp->flow_type & FLOW_EXT) && fsp->m_ext.vlan_tci) {
 		rule->filter.vlan_tci = ntohs(fsp->h_ext.vlan_tci);
+		rule->filter.vlan_tci_mask = ntohs(fsp->m_ext.vlan_tci);
 		rule->filter.match_flags |= IGC_FILTER_FLAG_VLAN_TCI;
 	}
 
@@ -1240,11 +1255,19 @@
 		memcpy(rule->filter.user_mask, fsp->m_ext.data, sizeof(fsp->m_ext.data));
 	}
 
-	/* When multiple filter options or user data or vlan etype is set, use a
-	 * flex filter.
+	/* The i225/i226 has various different filters. Flex filters provide a
+	 * way to match up to the first 128 bytes of a packet. Use them for:
+	 *   a) For specific user data
+	 *   b) For VLAN EtherType
+	 *   c) For full TCI match
+	 *   d) Or in case multiple filter criteria are set
+	 *
+	 * Otherwise, use the simple MAC, VLAN PRIO or EtherType filters.
 	 */
 	if ((rule->filter.match_flags & IGC_FILTER_FLAG_USER_DATA) ||
 	    (rule->filter.match_flags & IGC_FILTER_FLAG_VLAN_ETYPE) ||
+	    ((rule->filter.match_flags & IGC_FILTER_FLAG_VLAN_TCI) &&
+	     rule->filter.vlan_tci_mask == ntohs(VLAN_TCI_FULL_MASK)) ||
 	    (rule->filter.match_flags & (rule->filter.match_flags - 1)))
 		rule->flex = true;
 	else
@@ -1314,6 +1337,26 @@
 		return -EINVAL;
 	}
 
+	/* There are two ways to match the VLAN TCI:
+	 *  1. Match on PCP field and use vlan prio filter for it
+	 *  2. Match on complete TCI field and use flex filter for it
+	 */
+	if ((fsp->flow_type & FLOW_EXT) &&
+	    fsp->m_ext.vlan_tci &&
+	    fsp->m_ext.vlan_tci != htons(VLAN_PRIO_MASK) &&
+	    fsp->m_ext.vlan_tci != VLAN_TCI_FULL_MASK) {
+		netdev_dbg(netdev, "VLAN mask not supported\n");
+		return -EOPNOTSUPP;
+	}
+
+	/* VLAN EtherType can only be matched by full mask. */
+	if ((fsp->flow_type & FLOW_EXT) &&
+	    fsp->m_ext.vlan_etype &&
+	    fsp->m_ext.vlan_etype != ETHER_TYPE_FULL_MASK) {
+		netdev_dbg(netdev, "VLAN EtherType mask not supported\n");
+		return -EOPNOTSUPP;
+	}
+
 	if (fsp->location >= IGC_MAX_RXNFC_RULES) {
 		netdev_dbg(netdev, "Invalid location\n");
 		return -EINVAL;
@@ -1701,6 +1744,8 @@
 	/* twisted pair */
 	cmd->base.port = PORT_TP;
 	cmd->base.phy_address = hw->phy.addr;
+	ethtool_link_ksettings_add_link_mode(cmd, supported, TP);
+	ethtool_link_ksettings_add_link_mode(cmd, advertising, TP);
 
 	/* advertising link modes */
 	if (hw->phy.autoneg_advertised & ADVERTISE_10_HALF)
@@ -1801,7 +1846,7 @@
 	struct igc_adapter *adapter = netdev_priv(netdev);
 	struct net_device *dev = adapter->netdev;
 	struct igc_hw *hw = &adapter->hw;
-	u32 advertising;
+	u16 advertised = 0;
 
 	/* When adapter in resetting mode, autoneg/speed/duplex
 	 * cannot be changed
@@ -1826,18 +1871,33 @@
 	while (test_and_set_bit(__IGC_RESETTING, &adapter->state))
 		usleep_range(1000, 2000);
 
-	ethtool_convert_link_mode_to_legacy_u32(&advertising,
-						cmd->link_modes.advertising);
-	/* Converting to legacy u32 drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT.
-	 * We have to check this and convert it to ADVERTISE_2500_FULL
-	 * (aka ETHTOOL_LINK_MODE_2500baseX_Full_BIT) explicitly.
-	 */
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising, 2500baseT_Full))
-		advertising |= ADVERTISE_2500_FULL;
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  2500baseT_Full))
+		advertised |= ADVERTISE_2500_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  1000baseT_Full))
+		advertised |= ADVERTISE_1000_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  100baseT_Full))
+		advertised |= ADVERTISE_100_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  100baseT_Half))
+		advertised |= ADVERTISE_100_HALF;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  10baseT_Full))
+		advertised |= ADVERTISE_10_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  10baseT_Half))
+		advertised |= ADVERTISE_10_HALF;
 
 	if (cmd->base.autoneg == AUTONEG_ENABLE) {
 		hw->mac.autoneg = 1;
-		hw->phy.autoneg_advertised = advertising;
+		hw->phy.autoneg_advertised = advertised;
 		if (adapter->fc_autoneg)
 			hw->fc.requested_mode = igc_fc_default;
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_i225.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_i225.c
@@ -156,8 +156,15 @@
 {
 	u32 swfw_sync;
 
-	while (igc_get_hw_semaphore_i225(hw))
-		; /* Empty */
+	/* Releasing the resource requires first getting the HW semaphore.
+	 * If we fail to get the semaphore, there is nothing we can do,
+	 * except log an error and quit. We are not allowed to hang here
+	 * indefinitely, as it may cause denial of service or system crash.
+	 */
+	if (igc_get_hw_semaphore_i225(hw)) {
+		hw_dbg("Failed to release SW_FW_SYNC.\n");
+		return;
+	}
 
 	swfw_sync = rd32(IGC_SW_FW_SYNC);
 	swfw_sync &= ~mask;
@@ -636,7 +643,7 @@
 		ltrv = rd32(IGC_LTRMAXV);
 		if (ltr_max != (ltrv & IGC_LTRMAXV_LTRV_MASK)) {
 			ltrv = IGC_LTRMAXV_LSNP_REQ | ltr_max |
-			       (scale_min << IGC_LTRMAXV_SCALE_SHIFT);
+			       (scale_max << IGC_LTRMAXV_SCALE_SHIFT);
 			wr32(IGC_LTRMAXV, ltrv);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_main.c
@@ -254,6 +254,13 @@
 	/* reset BQL for queue */
 	netdev_tx_reset_queue(txring_txq(tx_ring));
 
+	/* Zero out the buffer ring */
+	memset(tx_ring->tx_buffer_info, 0,
+	       sizeof(*tx_ring->tx_buffer_info) * tx_ring->count);
+
+	/* Zero out the descriptor ring */
+	memset(tx_ring->desc, 0, tx_ring->size);
+
 	/* reset next_to_use and next_to_clean */
 	tx_ring->next_to_use = 0;
 	tx_ring->next_to_clean = 0;
@@ -267,7 +274,7 @@
  */
 void igc_free_tx_resources(struct igc_ring *tx_ring)
 {
-	igc_clean_tx_ring(tx_ring);
+	igc_disable_tx_ring(tx_ring);
 
 	vfree(tx_ring->tx_buffer_info);
 	tx_ring->tx_buffer_info = NULL;
@@ -309,6 +316,33 @@
 			igc_clean_tx_ring(adapter->tx_ring[i]);
 }
 
+static void igc_disable_tx_ring_hw(struct igc_ring *ring)
+{
+	struct igc_hw *hw = &ring->q_vector->adapter->hw;
+	u8 idx = ring->reg_idx;
+	u32 txdctl;
+
+	txdctl = rd32(IGC_TXDCTL(idx));
+	txdctl &= ~IGC_TXDCTL_QUEUE_ENABLE;
+	txdctl |= IGC_TXDCTL_SWFLUSH;
+	wr32(IGC_TXDCTL(idx), txdctl);
+}
+
+/**
+ * igc_disable_all_tx_rings_hw - Disable all transmit queue operation
+ * @adapter: board private structure
+ */
+static void igc_disable_all_tx_rings_hw(struct igc_adapter *adapter)
+{
+	int i;
+
+	for (i = 0; i < adapter->num_tx_queues; i++) {
+		struct igc_ring *tx_ring = adapter->tx_ring[i];
+
+		igc_disable_tx_ring_hw(tx_ring);
+	}
+}
+
 /**
  * igc_setup_tx_resources - allocate Tx resources (Descriptors)
  * @tx_ring: tx descriptor ring (for a specific queue) to setup
@@ -504,6 +538,9 @@
 	u8 index = rx_ring->queue_index;
 	int size, desc_len, res;
 
+	/* XDP RX-queue info */
+	if (xdp_rxq_info_is_reg(&rx_ring->xdp_rxq))
+		xdp_rxq_info_unreg(&rx_ring->xdp_rxq);
 	res = xdp_rxq_info_reg(&rx_ring->xdp_rxq, ndev, index,
 			       rx_ring->q_vector->napi.napi_id);
 	if (res < 0) {
@@ -637,8 +674,11 @@
 	else
 		buf_size = IGC_RXBUFFER_2048;
 
-	srrctl = IGC_RX_HDR_LEN << IGC_SRRCTL_BSIZEHDRSIZE_SHIFT;
-	srrctl |= buf_size >> IGC_SRRCTL_BSIZEPKT_SHIFT;
+	srrctl = rd32(IGC_SRRCTL(reg_idx));
+	srrctl &= ~(IGC_SRRCTL_BSIZEPKT_MASK | IGC_SRRCTL_BSIZEHDR_MASK |
+		    IGC_SRRCTL_DESCTYPE_MASK);
+	srrctl |= IGC_SRRCTL_BSIZEHDR(IGC_RX_HDR_LEN);
+	srrctl |= IGC_SRRCTL_BSIZEPKT(buf_size);
 	srrctl |= IGC_SRRCTL_DESCTYPE_ADV_ONEBUF;
 
 	wr32(IGC_SRRCTL(reg_idx), srrctl);
@@ -698,7 +738,6 @@
 	/* disable the queue */
 	wr32(IGC_TXDCTL(reg_idx), 0);
 	wrfl();
-	mdelay(10);
 
 	wr32(IGC_TDLEN(reg_idx),
 	     ring->count * sizeof(union igc_adv_tx_desc));
@@ -996,25 +1035,118 @@
 	return netdev_mc_count(netdev);
 }
 
-static __le32 igc_tx_launchtime(struct igc_adapter *adapter, ktime_t txtime)
+static __le32 igc_tx_launchtime(struct igc_ring *ring, ktime_t txtime,
+				bool *first_flag, bool *insert_empty)
 {
+	struct igc_adapter *adapter = netdev_priv(ring->netdev);
 	ktime_t cycle_time = adapter->cycle_time;
 	ktime_t base_time = adapter->base_time;
-	u32 launchtime;
+	ktime_t now = ktime_get_clocktai();
+	ktime_t baset_est, end_of_cycle;
+	s32 launchtime;
+	s64 n;
+
+	n = div64_s64(ktime_sub_ns(now, base_time), cycle_time);
+
+	baset_est = ktime_add_ns(base_time, cycle_time * (n));
+	end_of_cycle = ktime_add_ns(baset_est, cycle_time);
+
+	if (ktime_compare(txtime, end_of_cycle) >= 0) {
+		if (baset_est != ring->last_ff_cycle) {
+			*first_flag = true;
+			ring->last_ff_cycle = baset_est;
+
+			if (ktime_compare(end_of_cycle, ring->last_tx_cycle) > 0)
+				*insert_empty = true;
+		}
+	}
 
-	/* FIXME: when using ETF together with taprio, we may have a
-	 * case where 'delta' is larger than the cycle_time, this may
-	 * cause problems if we don't read the current value of
-	 * IGC_BASET, as the value writen into the launchtime
-	 * descriptor field may be misinterpreted.
+	/* Introducing a window at end of cycle on which packets
+	 * potentially not honor launchtime. Window of 5us chosen
+	 * considering software update the tail pointer and packets
+	 * are dma'ed to packet buffer.
 	 */
-	div_s64_rem(ktime_sub_ns(txtime, base_time), cycle_time, &launchtime);
+	if ((ktime_sub_ns(end_of_cycle, now) < 5 * NSEC_PER_USEC))
+		netdev_warn(ring->netdev, "Packet with txtime=%llu may not be honoured\n",
+			    txtime);
+
+	ring->last_tx_cycle = end_of_cycle;
+
+	launchtime = ktime_sub_ns(txtime, baset_est);
+	if (launchtime > 0)
+		div_s64_rem(launchtime, cycle_time, &launchtime);
+	else
+		launchtime = 0;
 
 	return cpu_to_le32(launchtime);
 }
 
+static int igc_init_empty_frame(struct igc_ring *ring,
+				struct igc_tx_buffer *buffer,
+				struct sk_buff *skb)
+{
+	unsigned int size;
+	dma_addr_t dma;
+
+	size = skb_headlen(skb);
+
+	dma = dma_map_single(ring->dev, skb->data, size, DMA_TO_DEVICE);
+	if (dma_mapping_error(ring->dev, dma)) {
+		netdev_err_once(ring->netdev, "Failed to map DMA for TX\n");
+		return -ENOMEM;
+	}
+
+	buffer->skb = skb;
+	buffer->protocol = 0;
+	buffer->bytecount = skb->len;
+	buffer->gso_segs = 1;
+	buffer->time_stamp = jiffies;
+	dma_unmap_len_set(buffer, len, skb->len);
+	dma_unmap_addr_set(buffer, dma, dma);
+
+	return 0;
+}
+
+static int igc_init_tx_empty_descriptor(struct igc_ring *ring,
+					struct sk_buff *skb,
+					struct igc_tx_buffer *first)
+{
+	union igc_adv_tx_desc *desc;
+	u32 cmd_type, olinfo_status;
+	int err;
+
+	if (!igc_desc_unused(ring))
+		return -EBUSY;
+
+	err = igc_init_empty_frame(ring, first, skb);
+	if (err)
+		return err;
+
+	cmd_type = IGC_ADVTXD_DTYP_DATA | IGC_ADVTXD_DCMD_DEXT |
+		   IGC_ADVTXD_DCMD_IFCS | IGC_TXD_DCMD |
+		   first->bytecount;
+	olinfo_status = first->bytecount << IGC_ADVTXD_PAYLEN_SHIFT;
+
+	desc = IGC_TX_DESC(ring, ring->next_to_use);
+	desc->read.cmd_type_len = cpu_to_le32(cmd_type);
+	desc->read.olinfo_status = cpu_to_le32(olinfo_status);
+	desc->read.buffer_addr = cpu_to_le64(dma_unmap_addr(first, dma));
+
+	netdev_tx_sent_queue(txring_txq(ring), skb->len);
+
+	first->next_to_watch = desc;
+
+	ring->next_to_use++;
+	if (ring->next_to_use == ring->count)
+		ring->next_to_use = 0;
+
+	return 0;
+}
+
+#define IGC_EMPTY_FRAME_SIZE 60
+
 static void igc_tx_ctxtdesc(struct igc_ring *tx_ring,
-			    struct igc_tx_buffer *first,
+			    __le32 launch_time, bool first_flag,
 			    u32 vlan_macip_lens, u32 type_tucmd,
 			    u32 mss_l4len_idx)
 {
@@ -1033,26 +1165,17 @@
 	if (test_bit(IGC_RING_FLAG_TX_CTX_IDX, &tx_ring->flags))
 		mss_l4len_idx |= tx_ring->reg_idx << 4;
 
+	if (first_flag)
+		mss_l4len_idx |= IGC_ADVTXD_TSN_CNTX_FIRST;
+
 	context_desc->vlan_macip_lens	= cpu_to_le32(vlan_macip_lens);
 	context_desc->type_tucmd_mlhl	= cpu_to_le32(type_tucmd);
 	context_desc->mss_l4len_idx	= cpu_to_le32(mss_l4len_idx);
-
-	/* We assume there is always a valid Tx time available. Invalid times
-	 * should have been handled by the upper layers.
-	 */
-	if (tx_ring->launchtime_enable) {
-		struct igc_adapter *adapter = netdev_priv(tx_ring->netdev);
-		ktime_t txtime = first->skb->tstamp;
-
-		skb_txtime_consumed(first->skb);
-		context_desc->launch_time = igc_tx_launchtime(adapter,
-							      txtime);
-	} else {
-		context_desc->launch_time = 0;
-	}
+	context_desc->launch_time	= launch_time;
 }
 
-static void igc_tx_csum(struct igc_ring *tx_ring, struct igc_tx_buffer *first)
+static void igc_tx_csum(struct igc_ring *tx_ring, struct igc_tx_buffer *first,
+			__le32 launch_time, bool first_flag)
 {
 	struct sk_buff *skb = first->skb;
 	u32 vlan_macip_lens = 0;
@@ -1092,7 +1215,8 @@
 	vlan_macip_lens |= skb_network_offset(skb) << IGC_ADVTXD_MACLEN_SHIFT;
 	vlan_macip_lens |= first->tx_flags & IGC_TX_FLAGS_VLAN_MASK;
 
-	igc_tx_ctxtdesc(tx_ring, first, vlan_macip_lens, type_tucmd, 0);
+	igc_tx_ctxtdesc(tx_ring, launch_time, first_flag,
+			vlan_macip_lens, type_tucmd, 0);
 }
 
 static int __igc_maybe_stop_tx(struct igc_ring *tx_ring, const u16 size)
@@ -1316,6 +1440,7 @@
 
 static int igc_tso(struct igc_ring *tx_ring,
 		   struct igc_tx_buffer *first,
+		   __le32 launch_time, bool first_flag,
 		   u8 *hdr_len)
 {
 	u32 vlan_macip_lens, type_tucmd, mss_l4len_idx;
@@ -1402,8 +1527,8 @@
 	vlan_macip_lens |= (ip.hdr - skb->data) << IGC_ADVTXD_MACLEN_SHIFT;
 	vlan_macip_lens |= first->tx_flags & IGC_TX_FLAGS_VLAN_MASK;
 
-	igc_tx_ctxtdesc(tx_ring, first, vlan_macip_lens,
-			type_tucmd, mss_l4len_idx);
+	igc_tx_ctxtdesc(tx_ring, launch_time, first_flag,
+			vlan_macip_lens, type_tucmd, mss_l4len_idx);
 
 	return 1;
 }
@@ -1411,11 +1536,14 @@
 static netdev_tx_t igc_xmit_frame_ring(struct sk_buff *skb,
 				       struct igc_ring *tx_ring)
 {
+	bool first_flag = false, insert_empty = false;
 	u16 count = TXD_USE_COUNT(skb_headlen(skb));
 	__be16 protocol = vlan_get_protocol(skb);
 	struct igc_tx_buffer *first;
+	__le32 launch_time = 0;
 	u32 tx_flags = 0;
 	unsigned short f;
+	ktime_t txtime;
 	u8 hdr_len = 0;
 	int tso = 0;
 
@@ -1429,11 +1557,40 @@
 		count += TXD_USE_COUNT(skb_frag_size(
 						&skb_shinfo(skb)->frags[f]));
 
-	if (igc_maybe_stop_tx(tx_ring, count + 3)) {
+	if (igc_maybe_stop_tx(tx_ring, count + 5)) {
 		/* this is a hard error */
 		return NETDEV_TX_BUSY;
 	}
 
+	if (!tx_ring->launchtime_enable)
+		goto done;
+
+	txtime = skb->tstamp;
+	skb->tstamp = ktime_set(0, 0);
+	launch_time = igc_tx_launchtime(tx_ring, txtime, &first_flag, &insert_empty);
+
+	if (insert_empty) {
+		struct igc_tx_buffer *empty_info;
+		struct sk_buff *empty;
+		void *data;
+
+		empty_info = &tx_ring->tx_buffer_info[tx_ring->next_to_use];
+		empty = alloc_skb(IGC_EMPTY_FRAME_SIZE, GFP_ATOMIC);
+		if (!empty)
+			goto done;
+
+		data = skb_put(empty, IGC_EMPTY_FRAME_SIZE);
+		memset(data, 0, IGC_EMPTY_FRAME_SIZE);
+
+		igc_tx_ctxtdesc(tx_ring, 0, false, 0, 0, 0);
+
+		if (igc_init_tx_empty_descriptor(tx_ring,
+						 empty,
+						 empty_info) < 0)
+			dev_kfree_skb_any(empty);
+	}
+
+done:
 	/* record the location of the first descriptor for this packet */
 	first = &tx_ring->tx_buffer_info[tx_ring->next_to_use];
 	first->type = IGC_TX_BUFFER_TYPE_SKB;
@@ -1448,9 +1605,10 @@
 		 * the other timer registers before skipping the
 		 * timestamping request.
 		 */
-		if (adapter->tstamp_config.tx_type == HWTSTAMP_TX_ON &&
-		    !test_and_set_bit_lock(__IGC_PTP_TX_IN_PROGRESS,
-					   &adapter->state)) {
+		unsigned long flags;
+
+		spin_lock_irqsave(&adapter->ptp_tx_lock, flags);
+		if (adapter->tstamp_config.tx_type == HWTSTAMP_TX_ON && !adapter->ptp_tx_skb) {
 			skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
 			tx_flags |= IGC_TX_FLAGS_TSTAMP;
 
@@ -1459,6 +1617,8 @@
 		} else {
 			adapter->tx_hwtstamp_skipped++;
 		}
+
+		spin_unlock_irqrestore(&adapter->ptp_tx_lock, flags);
 	}
 
 	if (skb_vlan_tag_present(skb)) {
@@ -1470,11 +1630,11 @@
 	first->tx_flags = tx_flags;
 	first->protocol = protocol;
 
-	tso = igc_tso(tx_ring, first, &hdr_len);
+	tso = igc_tso(tx_ring, first, launch_time, first_flag, &hdr_len);
 	if (tso < 0)
 		goto out_drop;
 	else if (!tso)
-		igc_tx_csum(tx_ring, first);
+		igc_tx_csum(tx_ring, first, launch_time, first_flag);
 
 	igc_tx_map(tx_ring, first, hdr_len);
 
@@ -1555,14 +1715,36 @@
 		   le32_to_cpu(rx_desc->wb.upper.status_error));
 }
 
+/* Mapping HW RSS Type to enum pkt_hash_types */
+static const enum pkt_hash_types igc_rss_type_table[IGC_RSS_TYPE_MAX_TABLE] = {
+	[IGC_RSS_TYPE_NO_HASH]		= PKT_HASH_TYPE_L2,
+	[IGC_RSS_TYPE_HASH_TCP_IPV4]	= PKT_HASH_TYPE_L4,
+	[IGC_RSS_TYPE_HASH_IPV4]	= PKT_HASH_TYPE_L3,
+	[IGC_RSS_TYPE_HASH_TCP_IPV6]	= PKT_HASH_TYPE_L4,
+	[IGC_RSS_TYPE_HASH_IPV6_EX]	= PKT_HASH_TYPE_L3,
+	[IGC_RSS_TYPE_HASH_IPV6]	= PKT_HASH_TYPE_L3,
+	[IGC_RSS_TYPE_HASH_TCP_IPV6_EX] = PKT_HASH_TYPE_L4,
+	[IGC_RSS_TYPE_HASH_UDP_IPV4]	= PKT_HASH_TYPE_L4,
+	[IGC_RSS_TYPE_HASH_UDP_IPV6]	= PKT_HASH_TYPE_L4,
+	[IGC_RSS_TYPE_HASH_UDP_IPV6_EX] = PKT_HASH_TYPE_L4,
+	[10] = PKT_HASH_TYPE_NONE, /* RSS Type above 9 "Reserved" by HW  */
+	[11] = PKT_HASH_TYPE_NONE, /* keep array sized for SW bit-mask   */
+	[12] = PKT_HASH_TYPE_NONE, /* to handle future HW revisons       */
+	[13] = PKT_HASH_TYPE_NONE,
+	[14] = PKT_HASH_TYPE_NONE,
+	[15] = PKT_HASH_TYPE_NONE,
+};
+
 static inline void igc_rx_hash(struct igc_ring *ring,
 			       union igc_adv_rx_desc *rx_desc,
 			       struct sk_buff *skb)
 {
-	if (ring->netdev->features & NETIF_F_RXHASH)
-		skb_set_hash(skb,
-			     le32_to_cpu(rx_desc->wb.lower.hi_dword.rss),
-			     PKT_HASH_TYPE_L3);
+	if (ring->netdev->features & NETIF_F_RXHASH) {
+		u32 rss_hash = le32_to_cpu(rx_desc->wb.lower.hi_dword.rss);
+		u32 rss_type = igc_rss_type(rx_desc);
+
+		skb_set_hash(skb, rss_hash, igc_rss_type_table[rss_type]);
+	}
 }
 
 static void igc_rx_vlan(struct igc_ring *rx_ring,
@@ -2434,21 +2616,24 @@
 static struct sk_buff *igc_construct_skb_zc(struct igc_ring *ring,
 					    struct xdp_buff *xdp)
 {
+	unsigned int totalsize = xdp->data_end - xdp->data_meta;
 	unsigned int metasize = xdp->data - xdp->data_meta;
-	unsigned int datasize = xdp->data_end - xdp->data;
-	unsigned int totalsize = metasize + datasize;
 	struct sk_buff *skb;
 
-	skb = __napi_alloc_skb(&ring->q_vector->napi,
-			       xdp->data_end - xdp->data_hard_start,
+	net_prefetch(xdp->data_meta);
+
+	skb = __napi_alloc_skb(&ring->q_vector->napi, totalsize,
 			       GFP_ATOMIC | __GFP_NOWARN);
 	if (unlikely(!skb))
 		return NULL;
 
-	skb_reserve(skb, xdp->data_meta - xdp->data_hard_start);
-	memcpy(__skb_put(skb, totalsize), xdp->data_meta, totalsize);
-	if (metasize)
+	memcpy(__skb_put(skb, totalsize), xdp->data_meta,
+	       ALIGN(totalsize, sizeof(long)));
+
+	if (metasize) {
 		skb_metadata_set(skb, metasize);
+		__skb_pull(skb, metasize);
+	}
 
 	return skb;
 }
@@ -2593,15 +2778,15 @@
 	struct netdev_queue *nq = txring_txq(ring);
 	union igc_adv_tx_desc *tx_desc = NULL;
 	int cpu = smp_processor_id();
-	u16 ntu = ring->next_to_use;
 	struct xdp_desc xdp_desc;
-	u16 budget;
+	u16 budget, ntu;
 
 	if (!netif_carrier_ok(ring->netdev))
 		return;
 
 	__netif_tx_lock(nq, cpu);
 
+	ntu = ring->next_to_use;
 	budget = igc_desc_unused(ring);
 
 	while (xsk_tx_peek_desc(pool, &xdp_desc) && budget--) {
@@ -2768,7 +2953,9 @@
 		if (tx_buffer->next_to_watch &&
 		    time_after(jiffies, tx_buffer->time_stamp +
 		    (adapter->tx_timeout_factor * HZ)) &&
-		    !(rd32(IGC_STATUS) & IGC_STATUS_TXOFF)) {
+		    !(rd32(IGC_STATUS) & IGC_STATUS_TXOFF) &&
+		    (rd32(IGC_TDH(tx_ring->reg_idx)) !=
+		     readl(tx_ring->tail))) {
 			/* detected Tx unit hang */
 			netdev_err(tx_ring->netdev,
 				   "Detected Tx Unit Hang\n"
@@ -4818,6 +5005,7 @@
 	/* clear VLAN promisc flag so VFTA will be updated if necessary */
 	adapter->flags &= ~IGC_FLAG_VLAN_PROMISC;
 
+	igc_disable_all_tx_rings_hw(adapter);
 	igc_clean_all_tx_rings(adapter);
 	igc_clean_all_rx_rings(adapter);
 }
@@ -4896,6 +5084,24 @@
 }
 
 /**
+ * igc_tx_timeout - Respond to a Tx Hang
+ * @netdev: network interface device structure
+ * @txqueue: queue number that timed out
+ **/
+static void igc_tx_timeout(struct net_device *netdev,
+			   unsigned int __always_unused txqueue)
+{
+	struct igc_adapter *adapter = netdev_priv(netdev);
+	struct igc_hw *hw = &adapter->hw;
+
+	/* Do the reset outside of interrupt context */
+	adapter->tx_timeout_count++;
+	schedule_work(&adapter->reset_task);
+	wr32(IGC_EICS,
+	     (adapter->eims_enable_mask & ~adapter->eims_other));
+}
+
+/**
  * igc_get_stats64 - Get System Network Statistics
  * @netdev: network interface device structure
  * @stats: rtnl_link_stats64 pointer
@@ -5322,10 +5528,17 @@
 			case SPEED_100:
 			case SPEED_1000:
 			case SPEED_2500:
-				adapter->tx_timeout_factor = 7;
+				adapter->tx_timeout_factor = 1;
 				break;
 			}
 
+			/* Once the launch time has been set on the wire, there
+			 * is a delay before the link speed can be determined
+			 * based on link-up activity. Write into the register
+			 * as soon as we know the correct link speed.
+			 */
+			igc_tsn_adjust_txtime_offset(adapter);
+
 			if (adapter->link_speed != SPEED_1000)
 				goto no_wait;
 
@@ -5466,6 +5679,9 @@
 			mod_timer(&adapter->watchdog_timer, jiffies + 1);
 	}
 
+	if (icr & IGC_ICR_TS)
+		igc_tsync_interrupt(adapter);
+
 	napi_schedule(&q_vector->napi);
 
 	return IRQ_HANDLED;
@@ -5509,6 +5725,9 @@
 			mod_timer(&adapter->watchdog_timer, jiffies + 1);
 	}
 
+	if (icr & IGC_ICR_TS)
+		igc_tsync_interrupt(adapter);
+
 	napi_schedule(&q_vector->napi);
 
 	return IRQ_HANDLED;
@@ -5772,6 +5991,7 @@
 			      const struct tc_taprio_qopt_offload *qopt)
 {
 	int queue_uses[IGC_MAX_TX_QUEUES] = { };
+	struct igc_hw *hw = &adapter->hw;
 	struct timespec64 now;
 	size_t n;
 
@@ -5784,14 +6004,17 @@
 	 * in the future, it will hold all the packets until that
 	 * time, causing a lot of TX Hangs, so to avoid that, we
 	 * reject schedules that would start in the future.
+	 * Note: Limitation above is no longer in i226.
 	 */
-	if (!is_base_time_past(qopt->base_time, &now))
+	if (!is_base_time_past(qopt->base_time, &now) &&
+	    igc_is_device_id_i225(hw))
 		return false;
 
 	for (n = 0; n < qopt->num_entries; n++) {
-		const struct tc_taprio_sched_entry *e;
+		const struct tc_taprio_sched_entry *e, *prev;
 		int i;
 
+		prev = n ? &qopt->entries[n - 1] : NULL;
 		e = &qopt->entries[n];
 
 		/* i225 only supports "global" frame preemption
@@ -5800,13 +6023,18 @@
 		if (e->command != TC_TAPRIO_CMD_SET_GATES)
 			return false;
 
-		for (i = 0; i < adapter->num_tx_queues; i++) {
-			if (e->gate_mask & BIT(i))
+		for (i = 0; i < adapter->num_tx_queues; i++)
+			if (e->gate_mask & BIT(i)) {
 				queue_uses[i]++;
 
-			if (queue_uses[i] > 1)
-				return false;
-		}
+				/* There are limitations: A single queue cannot
+				 * be opened and closed multiple times per cycle
+				 * unless the gate stays open. Check for it.
+				 */
+				if (queue_uses[i] > 1 &&
+				    !(prev->gate_mask & BIT(i)))
+					return false;
+			}
 	}
 
 	return true;
@@ -5848,12 +6076,19 @@
 static int igc_save_qbv_schedule(struct igc_adapter *adapter,
 				 struct tc_taprio_qopt_offload *qopt)
 {
+	bool queue_configured[IGC_MAX_TX_QUEUES] = { };
 	u32 start_time = 0, end_time = 0;
 	size_t n;
+	int i;
+
+	adapter->qbv_enable = qopt->enable;
 
 	if (!qopt->enable)
 		return igc_tsn_clear_schedule(adapter);
 
+	if (qopt->base_time < 0)
+		return -ERANGE;
+
 	if (adapter->base_time)
 		return -EALREADY;
 
@@ -5863,28 +6098,58 @@
 	adapter->cycle_time = qopt->cycle_time;
 	adapter->base_time = qopt->base_time;
 
-	/* FIXME: be a little smarter about cases when the gate for a
-	 * queue stays open for more than one entry.
-	 */
 	for (n = 0; n < qopt->num_entries; n++) {
 		struct tc_taprio_sched_entry *e = &qopt->entries[n];
-		int i;
 
 		end_time += e->interval;
 
+		/* If any of the conditions below are true, we need to manually
+		 * control the end time of the cycle.
+		 * 1. Qbv users can specify a cycle time that is not equal
+		 * to the total GCL intervals. Hence, recalculation is
+		 * necessary here to exclude the time interval that
+		 * exceeds the cycle time.
+		 * 2. According to IEEE Std. 802.1Q-2018 section 8.6.9.2,
+		 * once the end of the list is reached, it will switch
+		 * to the END_OF_CYCLE state and leave the gates in the
+		 * same state until the next cycle is started.
+		 */
+		if (end_time > adapter->cycle_time ||
+		    n + 1 == qopt->num_entries)
+			end_time = adapter->cycle_time;
+
 		for (i = 0; i < adapter->num_tx_queues; i++) {
 			struct igc_ring *ring = adapter->tx_ring[i];
 
 			if (!(e->gate_mask & BIT(i)))
 				continue;
 
-			ring->start_time = start_time;
+			/* Check whether a queue stays open for more than one
+			 * entry. If so, keep the start and advance the end
+			 * time.
+			 */
+			if (!queue_configured[i])
+				ring->start_time = start_time;
 			ring->end_time = end_time;
+
+			queue_configured[i] = true;
 		}
 
 		start_time += e->interval;
 	}
 
+	/* Check whether a queue gets configured.
+	 * If not, set the start and end time to be end time.
+	 */
+	for (i = 0; i < adapter->num_tx_queues; i++) {
+		if (!queue_configured[i]) {
+			struct igc_ring *ring = adapter->tx_ring[i];
+
+			ring->start_time = end_time;
+			ring->end_time = end_time;
+		}
+	}
+
 	return 0;
 }
 
@@ -6016,7 +6281,7 @@
 	struct igc_ring *ring;
 	int i, drops;
 
-	if (unlikely(test_bit(__IGC_DOWN, &adapter->state)))
+	if (unlikely(!netif_carrier_ok(dev)))
 		return -ENETDOWN;
 
 	if (unlikely(flags & ~XDP_XMIT_FLAGS_MASK))
@@ -6091,6 +6356,7 @@
 	.ndo_set_rx_mode	= igc_set_rx_mode,
 	.ndo_set_mac_address	= igc_set_mac,
 	.ndo_change_mtu		= igc_change_mtu,
+	.ndo_tx_timeout		= igc_tx_timeout,
 	.ndo_get_stats64	= igc_get_stats64,
 	.ndo_fix_features	= igc_fix_features,
 	.ndo_set_features	= igc_set_features,
@@ -6147,6 +6413,9 @@
 	u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr);
 	u32 value = 0;
 
+	if (IGC_REMOVED(hw_addr))
+		return ~value;
+
 	value = readl(&hw_addr[reg]);
 
 	/* reads should not return all F's */
@@ -6311,6 +6580,9 @@
 	memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops));
 	memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops));
 
+	if (pci_is_thunderbolt_attached(pdev))
+		msleep(600);
+
 	/* Initialize skew-specific constants */
 	err = ei->get_invariants(hw);
 	if (err)
@@ -6321,6 +6593,7 @@
 	netdev->features |= NETIF_F_TSO;
 	netdev->features |= NETIF_F_TSO6;
 	netdev->features |= NETIF_F_TSO_ECN;
+	netdev->features |= NETIF_F_RXHASH;
 	netdev->features |= NETIF_F_RXCSUM;
 	netdev->features |= NETIF_F_HW_CSUM;
 	netdev->features |= NETIF_F_SCTP_CRC;
@@ -6787,6 +7060,7 @@
 	rtnl_lock();
 	if (netif_running(netdev)) {
 		if (igc_open(netdev)) {
+			rtnl_unlock();
 			netdev_err(netdev, "igc_open failed after reset\n");
 			return;
 		}
@@ -6895,18 +7169,6 @@
 		igc_alloc_rx_buffers(ring, igc_desc_unused(ring));
 }
 
-static void igc_disable_tx_ring_hw(struct igc_ring *ring)
-{
-	struct igc_hw *hw = &ring->q_vector->adapter->hw;
-	u8 idx = ring->reg_idx;
-	u32 txdctl;
-
-	txdctl = rd32(IGC_TXDCTL(idx));
-	txdctl &= ~IGC_TXDCTL_QUEUE_ENABLE;
-	txdctl |= IGC_TXDCTL_SWFLUSH;
-	wr32(IGC_TXDCTL(idx), txdctl);
-}
-
 void igc_disable_tx_ring(struct igc_ring *ring)
 {
 	igc_disable_tx_ring_hw(ring);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_phy.c
@@ -581,7 +581,7 @@
 	 * the lower time out
 	 */
 	for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
-		usleep_range(500, 1000);
+		udelay(50);
 		mdic = rd32(IGC_MDIC);
 		if (mdic & IGC_MDIC_READY)
 			break;
@@ -638,7 +638,7 @@
 	 * the lower time out
 	 */
 	for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
-		usleep_range(500, 1000);
+		udelay(50);
 		mdic = rd32(IGC_MDIC);
 		if (mdic & IGC_MDIC_READY)
 			break;
@@ -746,8 +746,6 @@
 		if (ret_val)
 			return ret_val;
 		ret_val = igc_write_phy_reg_mdic(hw, offset, data);
-		if (ret_val)
-			return ret_val;
 		hw->phy.ops.release(hw);
 	} else {
 		ret_val = igc_write_xmdio_reg(hw, (u16)offset, dev_addr,
@@ -779,8 +777,6 @@
 		if (ret_val)
 			return ret_val;
 		ret_val = igc_read_phy_reg_mdic(hw, offset, data);
-		if (ret_val)
-			return ret_val;
 		hw->phy.ops.release(hw);
 	} else {
 		ret_val = igc_read_xmdio_reg(hw, (u16)offset, dev_addr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_ptp.c
@@ -323,7 +323,7 @@
 		ts = ns_to_timespec64(ns);
 		if (rq->perout.index == 1) {
 			if (use_freq) {
-				tsauxc_mask = IGC_TSAUXC_EN_CLK1;
+				tsauxc_mask = IGC_TSAUXC_EN_CLK1 | IGC_TSAUXC_ST1;
 				tsim_mask = 0;
 			} else {
 				tsauxc_mask = IGC_TSAUXC_EN_TT1;
@@ -334,7 +334,7 @@
 			freqout = IGC_FREQOUT1;
 		} else {
 			if (use_freq) {
-				tsauxc_mask = IGC_TSAUXC_EN_CLK0;
+				tsauxc_mask = IGC_TSAUXC_EN_CLK0 | IGC_TSAUXC_ST0;
 				tsim_mask = 0;
 			} else {
 				tsauxc_mask = IGC_TSAUXC_EN_TT0;
@@ -348,23 +348,44 @@
 		tsauxc = rd32(IGC_TSAUXC);
 		tsim = rd32(IGC_TSIM);
 		if (rq->perout.index == 1) {
-			tsauxc &= ~(IGC_TSAUXC_EN_TT1 | IGC_TSAUXC_EN_CLK1);
+			tsauxc &= ~(IGC_TSAUXC_EN_TT1 | IGC_TSAUXC_EN_CLK1 |
+				    IGC_TSAUXC_ST1);
 			tsim &= ~IGC_TSICR_TT1;
 		} else {
-			tsauxc &= ~(IGC_TSAUXC_EN_TT0 | IGC_TSAUXC_EN_CLK0);
+			tsauxc &= ~(IGC_TSAUXC_EN_TT0 | IGC_TSAUXC_EN_CLK0 |
+				    IGC_TSAUXC_ST0);
 			tsim &= ~IGC_TSICR_TT0;
 		}
 		if (on) {
+			struct timespec64 safe_start;
 			int i = rq->perout.index;
 
 			igc_pin_perout(igc, i, pin, use_freq);
-			igc->perout[i].start.tv_sec = rq->perout.start.sec;
+			igc_ptp_read(igc, &safe_start);
+
+			/* PPS output start time is triggered by Target time(TT)
+			 * register. Programming any past time value into TT
+			 * register will cause PPS to never start. Need to make
+			 * sure we program the TT register a time ahead in
+			 * future. There isn't a stringent need to fire PPS out
+			 * right away. Adding +2 seconds should take care of
+			 * corner cases. Let's say if the SYSTIML is close to
+			 * wrap up and the timer keeps ticking as we program the
+			 * register, adding +2seconds is safe bet.
+			 */
+			safe_start.tv_sec += 2;
+
+			if (rq->perout.start.sec < safe_start.tv_sec)
+				igc->perout[i].start.tv_sec = safe_start.tv_sec;
+			else
+				igc->perout[i].start.tv_sec = rq->perout.start.sec;
 			igc->perout[i].start.tv_nsec = rq->perout.start.nsec;
 			igc->perout[i].period.tv_sec = ts.tv_sec;
 			igc->perout[i].period.tv_nsec = ts.tv_nsec;
-			wr32(trgttimh, rq->perout.start.sec);
+			wr32(trgttimh, (u32)igc->perout[i].start.tv_sec);
 			/* For now, always select timer 0 as source. */
-			wr32(trgttiml, rq->perout.start.nsec | IGC_TT_IO_TIMER_SEL_SYSTIM0);
+			wr32(trgttiml, (u32)(igc->perout[i].start.tv_nsec |
+					     IGC_TT_IO_TIMER_SEL_SYSTIM0));
 			if (use_freq)
 				wr32(freqout, ns);
 			tsauxc |= tsauxc_mask;
@@ -416,10 +437,12 @@
  *
  * We need to convert the system time value stored in the RX/TXSTMP registers
  * into a hwtstamp which can be used by the upper level timestamping functions.
+ *
+ * Returns 0 on success.
  **/
-static void igc_ptp_systim_to_hwtstamp(struct igc_adapter *adapter,
-				       struct skb_shared_hwtstamps *hwtstamps,
-				       u64 systim)
+static int igc_ptp_systim_to_hwtstamp(struct igc_adapter *adapter,
+				      struct skb_shared_hwtstamps *hwtstamps,
+				      u64 systim)
 {
 	switch (adapter->hw.mac.type) {
 	case igc_i225:
@@ -429,8 +452,9 @@
 						systim & 0xFFFFFFFF);
 		break;
 	default:
-		break;
+		return -EINVAL;
 	}
+	return 0;
 }
 
 /**
@@ -603,6 +627,7 @@
 	return 0;
 }
 
+/* Requires adapter->ptp_tx_lock held by caller. */
 static void igc_ptp_tx_timeout(struct igc_adapter *adapter)
 {
 	struct igc_hw *hw = &adapter->hw;
@@ -610,7 +635,6 @@
 	dev_kfree_skb_any(adapter->ptp_tx_skb);
 	adapter->ptp_tx_skb = NULL;
 	adapter->tx_hwtstamp_timeouts++;
-	clear_bit_unlock(__IGC_PTP_TX_IN_PROGRESS, &adapter->state);
 	/* Clear the tx valid bit in TSYNCTXCTL register to enable interrupt. */
 	rd32(IGC_TXSTMPH);
 	netdev_warn(adapter->netdev, "Tx timestamp timeout\n");
@@ -618,20 +642,20 @@
 
 void igc_ptp_tx_hang(struct igc_adapter *adapter)
 {
-	bool timeout = time_is_before_jiffies(adapter->ptp_tx_start +
-					      IGC_PTP_TX_TIMEOUT);
+	unsigned long flags;
 
-	if (!test_bit(__IGC_PTP_TX_IN_PROGRESS, &adapter->state))
-		return;
+	spin_lock_irqsave(&adapter->ptp_tx_lock, flags);
 
-	/* If we haven't received a timestamp within the timeout, it is
-	 * reasonable to assume that it will never occur, so we can unlock the
-	 * timestamp bit when this occurs.
-	 */
-	if (timeout) {
-		cancel_work_sync(&adapter->ptp_tx_work);
-		igc_ptp_tx_timeout(adapter);
-	}
+	if (!adapter->ptp_tx_skb)
+		goto unlock;
+
+	if (time_is_after_jiffies(adapter->ptp_tx_start + IGC_PTP_TX_TIMEOUT))
+		goto unlock;
+
+	igc_ptp_tx_timeout(adapter);
+
+unlock:
+	spin_unlock_irqrestore(&adapter->ptp_tx_lock, flags);
 }
 
 /**
@@ -641,6 +665,8 @@
  * If we were asked to do hardware stamping and such a time stamp is
  * available, then it must have been for this skb here because we only
  * allow only one such packet into the queue.
+ *
+ * Context: Expects adapter->ptp_tx_lock to be held by caller.
  */
 static void igc_ptp_tx_hwtstamp(struct igc_adapter *adapter)
 {
@@ -655,7 +681,8 @@
 
 	regval = rd32(IGC_TXSTMPL);
 	regval |= (u64)rd32(IGC_TXSTMPH) << 32;
-	igc_ptp_systim_to_hwtstamp(adapter, &shhwtstamps, regval);
+	if (igc_ptp_systim_to_hwtstamp(adapter, &shhwtstamps, regval))
+		return;
 
 	switch (adapter->link_speed) {
 	case SPEED_10:
@@ -675,13 +702,7 @@
 	shhwtstamps.hwtstamp =
 		ktime_add_ns(shhwtstamps.hwtstamp, adjust);
 
-	/* Clear the lock early before calling skb_tstamp_tx so that
-	 * applications are not woken up before the lock bit is clear. We use
-	 * a copy of the skb pointer to ensure other threads can't change it
-	 * while we're notifying the stack.
-	 */
 	adapter->ptp_tx_skb = NULL;
-	clear_bit_unlock(__IGC_PTP_TX_IN_PROGRESS, &adapter->state);
 
 	/* Notify the stack and free the skb after we've unlocked */
 	skb_tstamp_tx(skb, &shhwtstamps);
@@ -692,24 +713,33 @@
  * igc_ptp_tx_work
  * @work: pointer to work struct
  *
- * This work function polls the TSYNCTXCTL valid bit to determine when a
- * timestamp has been taken for the current stored skb.
+ * This work function checks the TSYNCTXCTL valid bit to determine when
+ * a timestamp has been taken for the current stored skb.
  */
 static void igc_ptp_tx_work(struct work_struct *work)
 {
 	struct igc_adapter *adapter = container_of(work, struct igc_adapter,
 						   ptp_tx_work);
 	struct igc_hw *hw = &adapter->hw;
+	unsigned long flags;
 	u32 tsynctxctl;
 
-	if (!test_bit(__IGC_PTP_TX_IN_PROGRESS, &adapter->state))
-		return;
+	spin_lock_irqsave(&adapter->ptp_tx_lock, flags);
+
+	if (!adapter->ptp_tx_skb)
+		goto unlock;
 
 	tsynctxctl = rd32(IGC_TSYNCTXCTL);
-	if (WARN_ON_ONCE(!(tsynctxctl & IGC_TSYNCTXCTL_TXTT_0)))
-		return;
+	tsynctxctl &= IGC_TSYNCTXCTL_TXTT_0;
+	if (!tsynctxctl) {
+		WARN_ONCE(1, "Received a TSTAMP interrupt but no TSTAMP is ready.\n");
+		goto unlock;
+	}
 
 	igc_ptp_tx_hwtstamp(adapter);
+
+unlock:
+	spin_unlock_irqrestore(&adapter->ptp_tx_lock, flags);
 }
 
 /**
@@ -768,12 +798,25 @@
  */
 static bool igc_is_crosststamp_supported(struct igc_adapter *adapter)
 {
-	return IS_ENABLED(CONFIG_X86_TSC) ? pcie_ptm_enabled(adapter->pdev) : false;
+	if (!IS_ENABLED(CONFIG_X86_TSC))
+		return false;
+
+	/* FIXME: it was noticed that enabling support for PCIe PTM in
+	 * some i225-V models could cause lockups when bringing the
+	 * interface up/down. There should be no downsides to
+	 * disabling crosstimestamping support for i225-V, as it
+	 * doesn't have any PTP support. That way we gain some time
+	 * while root causing the issue.
+	 */
+	if (adapter->pdev->device == IGC_DEV_ID_I225_V)
+		return false;
+
+	return pcie_ptm_enabled(adapter->pdev);
 }
 
 static struct system_counterval_t igc_device_tstamp_to_system(u64 tstamp)
 {
-#if IS_ENABLED(CONFIG_X86_TSC)
+#if IS_ENABLED(CONFIG_X86_TSC) && !defined(CONFIG_UML)
 	return convert_art_ns_to_tsc(tstamp);
 #else
 	return (struct system_counterval_t) { };
@@ -945,6 +988,7 @@
 		return;
 	}
 
+	spin_lock_init(&adapter->ptp_tx_lock);
 	spin_lock_init(&adapter->tmreg_lock);
 	INIT_WORK(&adapter->ptp_tx_work, igc_ptp_tx_work);
 
@@ -983,6 +1027,17 @@
 	igc_ptp_write_i225(adapter, &ts);
 }
 
+static void igc_ptm_stop(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+	u32 ctrl;
+
+	ctrl = rd32(IGC_PTM_CTRL);
+	ctrl &= ~IGC_PTM_CTRL_EN;
+
+	wr32(IGC_PTM_CTRL, ctrl);
+}
+
 /**
  * igc_ptp_suspend - Disable PTP work items and prepare for suspend
  * @adapter: Board private structure
@@ -998,10 +1053,11 @@
 	cancel_work_sync(&adapter->ptp_tx_work);
 	dev_kfree_skb_any(adapter->ptp_tx_skb);
 	adapter->ptp_tx_skb = NULL;
-	clear_bit_unlock(__IGC_PTP_TX_IN_PROGRESS, &adapter->state);
 
-	if (pci_device_is_present(adapter->pdev))
+	if (pci_device_is_present(adapter->pdev)) {
 		igc_ptp_time_save(adapter);
+		igc_ptm_stop(adapter);
+	}
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_regs.h
@@ -227,6 +227,7 @@
 /* Transmit Scheduling Registers */
 #define IGC_TQAVCTRL		0x3570
 #define IGC_TXQCTL(_n)		(0x3344 + 0x4 * (_n))
+#define IGC_GTXOFFSET		0x3310
 #define IGC_BASET_L		0x3314
 #define IGC_BASET_H		0x3318
 #define IGC_QBVCYCLET		0x331C
@@ -306,7 +307,8 @@
 #define wr32(reg, val) \
 do { \
 	u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \
-	writel((val), &hw_addr[(reg)]); \
+	if (!IGC_REMOVED(hw_addr)) \
+		writel((val), &hw_addr[(reg)]); \
 } while (0)
 
 #define rd32(reg) (igc_rd32(hw, reg))
@@ -318,4 +320,6 @@
 
 #define array_rd32(reg, offset) (igc_rd32(hw, (reg) + ((offset) << 2)))
 
+#define IGC_REMOVED(h) unlikely(!(h))
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_tsn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_tsn.c
@@ -2,6 +2,7 @@
 /* Copyright (c)  2019 Intel Corporation */
 
 #include "igc.h"
+#include "igc_hw.h"
 #include "igc_tsn.h"
 
 static bool is_any_launchtime(struct igc_adapter *adapter)
@@ -36,7 +37,7 @@
 {
 	unsigned int new_flags = adapter->flags & ~IGC_FLAG_TSN_ANY_ENABLED;
 
-	if (adapter->base_time)
+	if (adapter->qbv_enable)
 		new_flags |= IGC_FLAG_TSN_QBV_ENABLED;
 
 	if (is_any_launchtime(adapter))
@@ -48,6 +49,51 @@
 	return new_flags;
 }
 
+static bool igc_tsn_is_tx_mode_in_tsn(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+
+	return !!(rd32(IGC_TQAVCTRL) & IGC_TQAVCTRL_TRANSMIT_MODE_TSN);
+}
+
+void igc_tsn_adjust_txtime_offset(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+	u16 txoffset;
+
+	if (!igc_tsn_is_tx_mode_in_tsn(adapter))
+		return;
+
+	switch (adapter->link_speed) {
+	case SPEED_10:
+		txoffset = IGC_TXOFFSET_SPEED_10;
+		break;
+	case SPEED_100:
+		txoffset = IGC_TXOFFSET_SPEED_100;
+		break;
+	case SPEED_1000:
+		txoffset = IGC_TXOFFSET_SPEED_1000;
+		break;
+	case SPEED_2500:
+		txoffset = IGC_TXOFFSET_SPEED_2500;
+		break;
+	default:
+		txoffset = 0;
+		break;
+	}
+
+	wr32(IGC_GTXOFFSET, txoffset);
+}
+
+static void igc_tsn_restore_retx_default(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+	u32 retxctl;
+
+	retxctl = rd32(IGC_RETX_CTL) & IGC_RETX_CTL_WATERMARK_MASK;
+	wr32(IGC_RETX_CTL, retxctl);
+}
+
 /* Returns the TSN specific registers to their default values after
  * the adapter is reset.
  */
@@ -57,12 +103,17 @@
 	u32 tqavctrl;
 	int i;
 
+	wr32(IGC_GTXOFFSET, 0);
 	wr32(IGC_TXPBS, I225_TXPBSIZE_DEFAULT);
 	wr32(IGC_DTXMXPKTSZ, IGC_DTXMXPKTSZ_DEFAULT);
 
+	if (igc_is_device_id_i226(hw))
+		igc_tsn_restore_retx_default(adapter);
+
 	tqavctrl = rd32(IGC_TQAVCTRL);
 	tqavctrl &= ~(IGC_TQAVCTRL_TRANSMIT_MODE_TSN |
-		      IGC_TQAVCTRL_ENHANCED_QAV);
+		      IGC_TQAVCTRL_ENHANCED_QAV | IGC_TQAVCTRL_FUTSCDDIS);
+
 	wr32(IGC_TQAVCTRL, tqavctrl);
 
 	for (i = 0; i < adapter->num_tx_queues; i++) {
@@ -79,6 +130,25 @@
 	return 0;
 }
 
+/* To partially fix i226 HW errata, reduce MAC internal buffering from 192 Bytes
+ * to 88 Bytes by setting RETX_CTL register using the recommendation from:
+ * a) Ethernet Controller I225/I226 Specification Update Rev 2.1
+ *    Item 9: TSN: Packet Transmission Might Cross the Qbv Window
+ * b) I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control
+ */
+static void igc_tsn_set_retx_qbvfullthreshold(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+	u32 retxctl, watermark;
+
+	retxctl = rd32(IGC_RETX_CTL);
+	watermark = retxctl & IGC_RETX_CTL_WATERMARK_MASK;
+	/* Set QBVFULLTH value using watermark and set QBVFULLEN */
+	retxctl |= (watermark << IGC_RETX_CTL_QBVFULLTH_SHIFT) |
+		   IGC_RETX_CTL_QBVFULLEN;
+	wr32(IGC_RETX_CTL, retxctl);
+}
+
 static int igc_tsn_enable_offload(struct igc_adapter *adapter)
 {
 	struct igc_hw *hw = &adapter->hw;
@@ -87,19 +157,12 @@
 	ktime_t base_time, systim;
 	int i;
 
-	cycle = adapter->cycle_time;
-	base_time = adapter->base_time;
-
 	wr32(IGC_TSAUXC, 0);
 	wr32(IGC_DTXMXPKTSZ, IGC_DTXMXPKTSZ_TSN);
 	wr32(IGC_TXPBS, IGC_TXPBSIZE_TSN);
 
-	tqavctrl = rd32(IGC_TQAVCTRL);
-	tqavctrl |= IGC_TQAVCTRL_TRANSMIT_MODE_TSN | IGC_TQAVCTRL_ENHANCED_QAV;
-	wr32(IGC_TQAVCTRL, tqavctrl);
-
-	wr32(IGC_QBVCYCLET_S, cycle);
-	wr32(IGC_QBVCYCLET, cycle);
+	if (igc_is_device_id_i226(hw))
+		igc_tsn_set_retx_qbvfullthreshold(adapter);
 
 	for (i = 0; i < adapter->num_tx_queues; i++) {
 		struct igc_ring *ring = adapter->tx_ring[i];
@@ -110,15 +173,8 @@
 		wr32(IGC_STQT(i), ring->start_time);
 		wr32(IGC_ENDQT(i), ring->end_time);
 
-		if (adapter->base_time) {
-			/* If we have a base_time we are in "taprio"
-			 * mode and we need to be strict about the
-			 * cycles: only transmit a packet if it can be
-			 * completed during that cycle.
-			 */
-			txqctl |= IGC_TXQCTL_STRICT_CYCLE |
-				IGC_TXQCTL_STRICT_END;
-		}
+		txqctl |= IGC_TXQCTL_STRICT_CYCLE |
+			IGC_TXQCTL_STRICT_END;
 
 		if (ring->launchtime_enable)
 			txqctl |= IGC_TXQCTL_QUEUE_MODE_LAUNCHT;
@@ -192,7 +248,7 @@
 			wr32(IGC_TQAVCC(i), tqavcc);
 
 			wr32(IGC_TQAVHC(i),
-			     0x80000000 + ring->hicredit * 0x7735);
+			     0x80000000 + ring->hicredit * 0x7736);
 		} else {
 			/* Disable any CBS for the queue */
 			txqctl &= ~(IGC_TXQCTL_QAV_SEL_MASK);
@@ -210,21 +266,43 @@
 		wr32(IGC_TXQCTL(i), txqctl);
 	}
 
+	tqavctrl = rd32(IGC_TQAVCTRL);
+	tqavctrl |= IGC_TQAVCTRL_TRANSMIT_MODE_TSN | IGC_TQAVCTRL_ENHANCED_QAV;
+
+	cycle = adapter->cycle_time;
+	base_time = adapter->base_time;
+
 	nsec = rd32(IGC_SYSTIML);
 	sec = rd32(IGC_SYSTIMH);
 
 	systim = ktime_set(sec, nsec);
-
 	if (ktime_compare(systim, base_time) > 0) {
-		s64 n;
+		s64 n = div64_s64(ktime_sub_ns(systim, base_time), cycle);
 
-		n = div64_s64(ktime_sub_ns(systim, base_time), cycle);
 		base_time = ktime_add_ns(base_time, (n + 1) * cycle);
+	} else {
+		/* According to datasheet section 7.5.2.9.3.3, FutScdDis bit
+		 * has to be configured before the cycle time and base time.
+		 */
+		if (igc_is_device_id_i226(hw))
+			tqavctrl |= IGC_TQAVCTRL_FUTSCDDIS;
 	}
 
-	baset_h = div_s64_rem(base_time, NSEC_PER_SEC, &baset_l);
+	wr32(IGC_TQAVCTRL, tqavctrl);
+
+	wr32(IGC_QBVCYCLET_S, cycle);
+	wr32(IGC_QBVCYCLET, cycle);
 
+	baset_h = div_s64_rem(base_time, NSEC_PER_SEC, &baset_l);
 	wr32(IGC_BASET_H, baset_h);
+
+	/* In i226, Future base time is only supported when FutScdDis bit
+	 * is enabled and only active for re-configuration.
+	 * In this case, initialize the base time with zero to create
+	 * "re-configuration" scenario then only set the desired base time.
+	 */
+	if (tqavctrl & IGC_TQAVCTRL_FUTSCDDIS)
+		wr32(IGC_BASET_L, 0);
 	wr32(IGC_BASET_L, baset_l);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/igc/igc_tsn.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/igc/igc_tsn.h
@@ -6,5 +6,6 @@
 
 int igc_tsn_offload_apply(struct igc_adapter *adapter);
 int igc_tsn_reset(struct igc_adapter *adapter);
+void igc_tsn_adjust_txtime_offset(struct igc_adapter *adapter);
 
 #endif /* _IGC_BASE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgb/ixgb_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgb/ixgb_hw.c
@@ -549,7 +549,7 @@
  *****************************************************************************/
 void
 ixgb_rar_set(struct ixgb_hw *hw,
-		  u8 *addr,
+		  const u8 *addr,
 		  u32 index)
 {
 	u32 rar_low, rar_high;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgb/ixgb_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgb/ixgb_hw.h
@@ -740,7 +740,7 @@
 void ixgb_check_for_link(struct ixgb_hw *hw);
 bool ixgb_check_for_bad_link(struct ixgb_hw *hw);
 
-void ixgb_rar_set(struct ixgb_hw *hw, u8 *addr, u32 index);
+void ixgb_rar_set(struct ixgb_hw *hw, const u8 *addr, u32 index);
 
 /* Filters (multicast, vlan, receive) */
 void ixgb_mc_addr_list_update(struct ixgb_hw *hw, u8 *mc_addr_list,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe.h
@@ -67,6 +67,8 @@
 #define IXGBE_RXBUFFER_4K    4096
 #define IXGBE_MAX_RXBUFFER  16384  /* largest size for a single descriptor */
 
+#define IXGBE_PKT_HDR_PAD   (ETH_HLEN + ETH_FCS_LEN + (VLAN_HLEN * 2))
+
 /* Attempt to maximize the headroom available for incoming frames.  We
  * use a 2K buffer for receives and need 1536/1534 to store the data for
  * the frame.  This leaves us with 512 bytes of room.  From that we need
@@ -177,11 +179,14 @@
 	u16 pf_vlan; /* When set, guest VLAN config not allowed. */
 	u16 pf_qos;
 	u16 tx_rate;
+	int link_enable;
+	int link_state;
 	u8 spoofchk_enabled;
 	bool rss_query_enabled;
 	u8 trusted;
 	int xcast_mode;
 	unsigned int vf_api;
+	u8 primary_abort_count;
 };
 
 enum ixgbevf_xcast_modes {
@@ -553,6 +558,8 @@
 #define IXGBE_TRY_LINK_TIMEOUT (4 * HZ)
 #define IXGBE_SFP_POLL_JIFFIES (2 * HZ)	/* SFP poll every 2 seconds */
 
+#define IXGBE_PRIMARY_ABORT_LIMIT	5
+
 /* board specific private data structure */
 struct ixgbe_adapter {
 	unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)];
@@ -611,6 +618,7 @@
 #define IXGBE_FLAG2_RX_LEGACY			BIT(16)
 #define IXGBE_FLAG2_IPSEC_ENABLED		BIT(17)
 #define IXGBE_FLAG2_VF_IPSEC_ENABLED		BIT(18)
+#define IXGBE_FLAG2_AUTO_DISABLE_VF		BIT(19)
 
 	/* Tx fast path data */
 	int num_tx_queues;
@@ -770,6 +778,7 @@
 #ifdef CONFIG_IXGBE_IPSEC
 	struct ixgbe_ipsec *ipsec;
 #endif /* CONFIG_IXGBE_IPSEC */
+	spinlock_t vfs_lock;
 };
 
 static inline u8 ixgbe_max_rss_indices(struct ixgbe_adapter *adapter)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
@@ -123,14 +123,14 @@
 		if (ret_val)
 			return ret_val;
 		if (hw->phy.sfp_type == ixgbe_sfp_type_unknown)
-			return IXGBE_ERR_SFP_NOT_SUPPORTED;
+			return -EOPNOTSUPP;
 
 		/* Check to see if SFP+ module is supported */
 		ret_val = ixgbe_get_sfp_init_sequence_offsets(hw,
 							    &list_offset,
 							    &data_offset);
 		if (ret_val)
-			return IXGBE_ERR_SFP_NOT_SUPPORTED;
+			return -EOPNOTSUPP;
 		break;
 	default:
 		break;
@@ -213,7 +213,7 @@
 		break;
 
 	default:
-		return IXGBE_ERR_LINK_SETUP;
+		return -EIO;
 	}
 
 	return 0;
@@ -283,7 +283,7 @@
 
 	/* Validate the water mark configuration */
 	if (!hw->fc.pause_time)
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 
 	/* Low water mark of zero causes XOFF floods */
 	for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
@@ -292,7 +292,7 @@
 			if (!hw->fc.low_water[i] ||
 			    hw->fc.low_water[i] >= hw->fc.high_water[i]) {
 				hw_dbg(hw, "Invalid water mark configuration\n");
-				return IXGBE_ERR_INVALID_LINK_SETTINGS;
+				return -EINVAL;
 			}
 		}
 	}
@@ -369,7 +369,7 @@
 		break;
 	default:
 		hw_dbg(hw, "Flow control param set incorrectly\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	/* Set 802.3x based flow control settings. */
@@ -438,7 +438,7 @@
 				msleep(100);
 			}
 			if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
-				status = IXGBE_ERR_AUTONEG_NOT_COMPLETE;
+				status = -EIO;
 				hw_dbg(hw, "Autonegotiation did not complete.\n");
 			}
 		}
@@ -478,7 +478,7 @@
 
 	if (timeout == IXGBE_VALIDATE_LINK_READY_TIMEOUT) {
 		hw_dbg(hw, "Link was indicated but link is down\n");
-		return IXGBE_ERR_LINK_SETUP;
+		return -EIO;
 	}
 
 	return 0;
@@ -594,7 +594,7 @@
 	speed &= link_capabilities;
 
 	if (speed == IXGBE_LINK_SPEED_UNKNOWN)
-		return IXGBE_ERR_LINK_SETUP;
+		return -EINVAL;
 
 	/* Set KX4/KX support according to speed requested */
 	else if (link_mode == IXGBE_AUTOC_LMS_KX4_AN ||
@@ -701,9 +701,9 @@
 
 		/* Init PHY and function pointers, perform SFP setup */
 		phy_status = hw->phy.ops.init(hw);
-		if (phy_status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+		if (phy_status == -EOPNOTSUPP)
 			return phy_status;
-		if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
+		if (phy_status == -ENOENT)
 			goto mac_reset_top;
 
 		hw->phy.ops.reset(hw);
@@ -727,7 +727,7 @@
 		udelay(1);
 	}
 	if (ctrl & IXGBE_CTRL_RST) {
-		status = IXGBE_ERR_RESET_FAILED;
+		status = -EIO;
 		hw_dbg(hw, "Reset polling failed to complete.\n");
 	}
 
@@ -789,7 +789,7 @@
 	/* Make sure we are using a valid rar index range */
 	if (rar >= rar_entries) {
 		hw_dbg(hw, "RAR index %d is out of range.\n", rar);
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
@@ -814,7 +814,7 @@
 	/* Make sure we are using a valid rar index range */
 	if (rar >= rar_entries) {
 		hw_dbg(hw, "RAR index %d is out of range.\n", rar);
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
@@ -845,7 +845,7 @@
 	u32 vftabyte;
 
 	if (vlan > 4095)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* Determine 32-bit word position in array */
 	regindex = (vlan >> 5) & 0x7F;   /* upper seven bits */
@@ -964,7 +964,7 @@
 		gssr = IXGBE_GSSR_PHY0_SM;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, gssr) != 0)
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	if (hw->phy.type == ixgbe_phy_nl) {
 		/*
@@ -993,7 +993,7 @@
 
 		if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_PASS) {
 			hw_dbg(hw, "EEPROM read did not pass.\n");
-			status = IXGBE_ERR_SFP_NOT_PRESENT;
+			status = -ENOENT;
 			goto out;
 		}
 
@@ -1003,7 +1003,7 @@
 
 		*eeprom_data = (u8)(sfp_data >> 8);
 	} else {
-		status = IXGBE_ERR_PHY;
+		status = -EIO;
 	}
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
@@ -117,7 +117,7 @@
 		ret_val = hw->mac.ops.acquire_swfw_sync(hw,
 							IXGBE_GSSR_MAC_CSR_SM);
 		if (ret_val)
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 
 		if (hw->eeprom.ops.read(hw, ++data_offset, &data_value))
 			goto setup_sfp_err;
@@ -144,7 +144,7 @@
 
 		if (ret_val) {
 			hw_dbg(hw, " sfp module setup not complete\n");
-			return IXGBE_ERR_SFP_SETUP_NOT_COMPLETE;
+			return -EIO;
 		}
 	}
 
@@ -159,7 +159,7 @@
 	usleep_range(hw->eeprom.semaphore_delay * 1000,
 		     hw->eeprom.semaphore_delay * 2000);
 	hw_err(hw, "eeprom read at offset %d failed\n", data_offset);
-	return IXGBE_ERR_SFP_SETUP_NOT_COMPLETE;
+	return -EIO;
 }
 
 /**
@@ -184,7 +184,7 @@
 		ret_val = hw->mac.ops.acquire_swfw_sync(hw,
 					IXGBE_GSSR_MAC_CSR_SM);
 		if (ret_val)
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 
 		*locked = true;
 	}
@@ -219,7 +219,7 @@
 		ret_val = hw->mac.ops.acquire_swfw_sync(hw,
 					IXGBE_GSSR_MAC_CSR_SM);
 		if (ret_val)
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 
 		locked = true;
 	}
@@ -400,7 +400,7 @@
 		break;
 
 	default:
-		return IXGBE_ERR_LINK_SETUP;
+		return -EIO;
 	}
 
 	if (hw->phy.multispeed_fiber) {
@@ -541,7 +541,7 @@
 				msleep(100);
 			}
 			if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
-				status = IXGBE_ERR_AUTONEG_NOT_COMPLETE;
+				status = -EIO;
 				hw_dbg(hw, "Autoneg did not complete.\n");
 			}
 		}
@@ -794,7 +794,7 @@
 	speed &= link_capabilities;
 
 	if (speed == IXGBE_LINK_SPEED_UNKNOWN)
-		return IXGBE_ERR_LINK_SETUP;
+		return -EINVAL;
 
 	/* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/
 	if (hw->mac.orig_link_settings_stored)
@@ -861,8 +861,7 @@
 					msleep(100);
 				}
 				if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
-					status =
-						IXGBE_ERR_AUTONEG_NOT_COMPLETE;
+					status = -EIO;
 					hw_dbg(hw, "Autoneg did not complete.\n");
 				}
 			}
@@ -927,7 +926,7 @@
 	/* Identify PHY and related function pointers */
 	status = hw->phy.ops.init(hw);
 
-	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+	if (status == -EOPNOTSUPP)
 		return status;
 
 	/* Setup SFP module if there is one present. */
@@ -936,7 +935,7 @@
 		hw->phy.sfp_setup_needed = false;
 	}
 
-	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+	if (status == -EOPNOTSUPP)
 		return status;
 
 	/* Reset PHY */
@@ -974,7 +973,7 @@
 	}
 
 	if (ctrl & IXGBE_CTRL_RST_MASK) {
-		status = IXGBE_ERR_RESET_FAILED;
+		status = -EIO;
 		hw_dbg(hw, "Reset polling failed to complete.\n");
 	}
 
@@ -1093,7 +1092,7 @@
 		udelay(10);
 	}
 
-	return IXGBE_ERR_FDIR_CMD_INCOMPLETE;
+	return -EIO;
 }
 
 /**
@@ -1155,7 +1154,7 @@
 	}
 	if (i >= IXGBE_FDIR_INIT_DONE_POLL) {
 		hw_dbg(hw, "Flow Director Signature poll time exceeded!\n");
-		return IXGBE_ERR_FDIR_REINIT_FAILED;
+		return -EIO;
 	}
 
 	/* Clear FDIR statistics registers (read to clear) */
@@ -1387,7 +1386,7 @@
 		break;
 	default:
 		hw_dbg(hw, " Error on flow type input\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	/* configure FDIRCMD register */
@@ -1546,7 +1545,7 @@
 		break;
 	default:
 		hw_dbg(hw, " Error on vm pool mask\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	switch (input_mask->formatted.flow_type & IXGBE_ATR_L4TYPE_MASK) {
@@ -1555,14 +1554,14 @@
 		if (input_mask->formatted.dst_port ||
 		    input_mask->formatted.src_port) {
 			hw_dbg(hw, " Error on src/dst port mask\n");
-			return IXGBE_ERR_CONFIG;
+			return -EIO;
 		}
 		break;
 	case IXGBE_ATR_L4TYPE_MASK:
 		break;
 	default:
 		hw_dbg(hw, " Error on flow type mask\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	switch (ntohs(input_mask->formatted.vlan_id) & 0xEFFF) {
@@ -1583,7 +1582,7 @@
 		break;
 	default:
 		hw_dbg(hw, " Error on VLAN mask\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	switch ((__force u16)input_mask->formatted.flex_bytes & 0xFFFF) {
@@ -1595,7 +1594,7 @@
 		break;
 	default:
 		hw_dbg(hw, " Error on flexible byte mask\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	/* Now mask VM pool and destination IPv6 - bits 5 and 2 */
@@ -1824,7 +1823,7 @@
 
 	/* Return error if SFP module has been detected but is not supported */
 	if (hw->phy.type == ixgbe_phy_sfp_unsupported)
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 
 	return status;
 }
@@ -1863,13 +1862,13 @@
  *  Verifies that installed the firmware version is 0.6 or higher
  *  for SFI devices. All 82599 SFI devices should have version 0.6 or higher.
  *
- *  Returns IXGBE_ERR_EEPROM_VERSION if the FW is not present or
- *  if the FW version is not supported.
+ *  Return: -EACCES if the FW is not present or if the FW version is
+ *  not supported.
  **/
 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw)
 {
-	s32 status = IXGBE_ERR_EEPROM_VERSION;
 	u16 fw_offset, fw_ptp_cfg_offset;
+	s32 status = -EACCES;
 	u16 offset;
 	u16 fw_version = 0;
 
@@ -1883,7 +1882,7 @@
 		goto fw_version_err;
 
 	if (fw_offset == 0 || fw_offset == 0xFFFF)
-		return IXGBE_ERR_EEPROM_VERSION;
+		return -EACCES;
 
 	/* get the offset to the Pass Through Patch Configuration block */
 	offset = fw_offset + IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR;
@@ -1891,7 +1890,7 @@
 		goto fw_version_err;
 
 	if (fw_ptp_cfg_offset == 0 || fw_ptp_cfg_offset == 0xFFFF)
-		return IXGBE_ERR_EEPROM_VERSION;
+		return -EACCES;
 
 	/* get the firmware version */
 	offset = fw_ptp_cfg_offset + IXGBE_FW_PATCH_VERSION_4;
@@ -1905,7 +1904,7 @@
 
 fw_version_err:
 	hw_err(hw, "eeprom read at offset %d failed\n", offset);
-	return IXGBE_ERR_EEPROM_VERSION;
+	return -EACCES;
 }
 
 /**
@@ -2038,7 +2037,7 @@
 
 	if (!(anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK)) {
 		hw_dbg(hw, "auto negotiation not completed\n");
-		ret_val = IXGBE_ERR_RESET_FAILED;
+		ret_val = -EIO;
 		goto reset_pipeline_out;
 	}
 
@@ -2087,7 +2086,7 @@
 
 		if (!timeout) {
 			hw_dbg(hw, "Driver can't access resource, acquiring I2C bus timeout.\n");
-			status = IXGBE_ERR_I2C;
+			status = -EIO;
 			goto release_i2c_access;
 		}
 	}
@@ -2141,7 +2140,7 @@
 
 		if (!timeout) {
 			hw_dbg(hw, "Driver can't access resource, acquiring I2C bus timeout.\n");
-			status = IXGBE_ERR_I2C;
+			status = -EIO;
 			goto release_i2c_access;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -30,7 +30,7 @@
 					     u16 words, u16 *data);
 static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
 						 u16 offset);
-static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
+static s32 ixgbe_disable_pcie_primary(struct ixgbe_hw *hw);
 
 /* Base table for registers values that change by MAC */
 const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = {
@@ -124,7 +124,7 @@
 	 */
 	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
 		hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 	}
 
 	/*
@@ -215,7 +215,7 @@
 		break;
 	default:
 		hw_dbg(hw, "Flow control param set incorrectly\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	if (hw->mac.type != ixgbe_mac_X540) {
@@ -500,7 +500,7 @@
 
 	if (pba_num == NULL) {
 		hw_dbg(hw, "PBA string buffer was null\n");
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data);
@@ -526,7 +526,7 @@
 		/* we will need 11 characters to store the PBA */
 		if (pba_num_size < 11) {
 			hw_dbg(hw, "PBA string buffer too small\n");
-			return IXGBE_ERR_NO_SPACE;
+			return -ENOSPC;
 		}
 
 		/* extract hex string from data and pba_ptr */
@@ -563,13 +563,13 @@
 
 	if (length == 0xFFFF || length == 0) {
 		hw_dbg(hw, "NVM PBA number section invalid length\n");
-		return IXGBE_ERR_PBA_SECTION;
+		return -EIO;
 	}
 
 	/* check if pba_num buffer is big enough */
 	if (pba_num_size  < (((u32)length * 2) - 1)) {
 		hw_dbg(hw, "PBA string buffer too small\n");
-		return IXGBE_ERR_NO_SPACE;
+		return -ENOSPC;
 	}
 
 	/* trim pba length from start of string */
@@ -746,10 +746,10 @@
 	usleep_range(1000, 2000);
 
 	/*
-	 * Prevent the PCI-E bus from from hanging by disabling PCI-E master
+	 * Prevent the PCI-E bus from hanging by disabling PCI-E primary
 	 * access and verify no pending requests
 	 */
-	return ixgbe_disable_pcie_master(hw);
+	return ixgbe_disable_pcie_primary(hw);
 }
 
 /**
@@ -805,7 +805,7 @@
 	u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
 
 	if (index > 3)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* To turn on the LED, set mode to ON. */
 	led_reg &= ~IXGBE_LED_MODE_MASK(index);
@@ -826,7 +826,7 @@
 	u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
 
 	if (index > 3)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* To turn off the LED, set mode to OFF. */
 	led_reg &= ~IXGBE_LED_MODE_MASK(index);
@@ -904,11 +904,8 @@
 
 	hw->eeprom.ops.init_params(hw);
 
-	if (words == 0)
-		return IXGBE_ERR_INVALID_ARGUMENT;
-
-	if (offset + words > hw->eeprom.word_size)
-		return IXGBE_ERR_EEPROM;
+	if (words == 0 || (offset + words > hw->eeprom.word_size))
+		return -EINVAL;
 
 	/*
 	 * The EEPROM page size cannot be queried from the chip. We do lazy
@@ -962,7 +959,7 @@
 
 	if (ixgbe_ready_eeprom(hw) != 0) {
 		ixgbe_release_eeprom(hw);
-		return IXGBE_ERR_EEPROM;
+		return -EIO;
 	}
 
 	for (i = 0; i < words; i++) {
@@ -1028,7 +1025,7 @@
 	hw->eeprom.ops.init_params(hw);
 
 	if (offset >= hw->eeprom.word_size)
-		return IXGBE_ERR_EEPROM;
+		return -EINVAL;
 
 	return ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data);
 }
@@ -1050,11 +1047,8 @@
 
 	hw->eeprom.ops.init_params(hw);
 
-	if (words == 0)
-		return IXGBE_ERR_INVALID_ARGUMENT;
-
-	if (offset + words > hw->eeprom.word_size)
-		return IXGBE_ERR_EEPROM;
+	if (words == 0 || (offset + words > hw->eeprom.word_size))
+		return -EINVAL;
 
 	/*
 	 * We cannot hold synchronization semaphores for too long
@@ -1099,7 +1093,7 @@
 
 	if (ixgbe_ready_eeprom(hw) != 0) {
 		ixgbe_release_eeprom(hw);
-		return IXGBE_ERR_EEPROM;
+		return -EIO;
 	}
 
 	for (i = 0; i < words; i++) {
@@ -1142,7 +1136,7 @@
 	hw->eeprom.ops.init_params(hw);
 
 	if (offset >= hw->eeprom.word_size)
-		return IXGBE_ERR_EEPROM;
+		return -EINVAL;
 
 	return ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
 }
@@ -1165,11 +1159,8 @@
 
 	hw->eeprom.ops.init_params(hw);
 
-	if (words == 0)
-		return IXGBE_ERR_INVALID_ARGUMENT;
-
-	if (offset >= hw->eeprom.word_size)
-		return IXGBE_ERR_EEPROM;
+	if (words == 0 || offset >= hw->eeprom.word_size)
+		return -EINVAL;
 
 	for (i = 0; i < words; i++) {
 		eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
@@ -1262,11 +1253,8 @@
 
 	hw->eeprom.ops.init_params(hw);
 
-	if (words == 0)
-		return IXGBE_ERR_INVALID_ARGUMENT;
-
-	if (offset >= hw->eeprom.word_size)
-		return IXGBE_ERR_EEPROM;
+	if (words == 0 || offset >= hw->eeprom.word_size)
+		return -EINVAL;
 
 	for (i = 0; i < words; i++) {
 		eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
@@ -1328,7 +1316,7 @@
 		}
 		udelay(5);
 	}
-	return IXGBE_ERR_EEPROM;
+	return -EIO;
 }
 
 /**
@@ -1344,7 +1332,7 @@
 	u32 i;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
 
@@ -1366,7 +1354,7 @@
 		hw_dbg(hw, "Could not acquire EEPROM grant\n");
 
 		hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
-		return IXGBE_ERR_EEPROM;
+		return -EIO;
 	}
 
 	/* Setup EEPROM for Read/Write */
@@ -1419,7 +1407,7 @@
 		swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
 		if (swsm & IXGBE_SWSM_SMBI) {
 			hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n");
-			return IXGBE_ERR_EEPROM;
+			return -EIO;
 		}
 	}
 
@@ -1447,7 +1435,7 @@
 	if (i >= timeout) {
 		hw_dbg(hw, "SWESMBI Software EEPROM semaphore not granted.\n");
 		ixgbe_release_eeprom_semaphore(hw);
-		return IXGBE_ERR_EEPROM;
+		return -EIO;
 	}
 
 	return 0;
@@ -1503,7 +1491,7 @@
 	 */
 	if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) {
 		hw_dbg(hw, "SPI EEPROM Status error\n");
-		return IXGBE_ERR_EEPROM;
+		return -EIO;
 	}
 
 	return 0;
@@ -1715,7 +1703,7 @@
 	for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) {
 		if (hw->eeprom.ops.read(hw, i, &pointer)) {
 			hw_dbg(hw, "EEPROM read failed\n");
-			return IXGBE_ERR_EEPROM;
+			return -EIO;
 		}
 
 		/* If the pointer seems invalid */
@@ -1724,7 +1712,7 @@
 
 		if (hw->eeprom.ops.read(hw, pointer, &length)) {
 			hw_dbg(hw, "EEPROM read failed\n");
-			return IXGBE_ERR_EEPROM;
+			return -EIO;
 		}
 
 		if (length == 0xFFFF || length == 0)
@@ -1733,7 +1721,7 @@
 		for (j = pointer + 1; j <= pointer + length; j++) {
 			if (hw->eeprom.ops.read(hw, j, &word)) {
 				hw_dbg(hw, "EEPROM read failed\n");
-				return IXGBE_ERR_EEPROM;
+				return -EIO;
 			}
 			checksum += word;
 		}
@@ -1786,7 +1774,7 @@
 	 * calculated checksum
 	 */
 	if (read_checksum != checksum)
-		status = IXGBE_ERR_EEPROM_CHECKSUM;
+		status = -EIO;
 
 	/* If the user cares, return the calculated checksum */
 	if (checksum_val)
@@ -1845,7 +1833,7 @@
 	/* Make sure we are using a valid rar index range */
 	if (index >= rar_entries) {
 		hw_dbg(hw, "RAR index %d is out of range.\n", index);
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	/* setup VMDq pool selection before this RAR gets enabled */
@@ -1897,7 +1885,7 @@
 	/* Make sure we are using a valid rar index range */
 	if (index >= rar_entries) {
 		hw_dbg(hw, "RAR index %d is out of range.\n", index);
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	/*
@@ -2146,7 +2134,7 @@
 
 	/* Validate the water mark configuration. */
 	if (!hw->fc.pause_time)
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 
 	/* Low water mark of zero causes XOFF floods */
 	for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
@@ -2155,7 +2143,7 @@
 			if (!hw->fc.low_water[i] ||
 			    hw->fc.low_water[i] >= hw->fc.high_water[i]) {
 				hw_dbg(hw, "Invalid water mark configuration\n");
-				return IXGBE_ERR_INVALID_LINK_SETTINGS;
+				return -EINVAL;
 			}
 		}
 	}
@@ -2212,7 +2200,7 @@
 		break;
 	default:
 		hw_dbg(hw, "Flow control param set incorrectly\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	/* Set 802.3x based flow control settings. */
@@ -2269,7 +2257,7 @@
 		       u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
 {
 	if ((!(adv_reg)) ||  (!(lp_reg)))
-		return IXGBE_ERR_FC_NOT_NEGOTIATED;
+		return -EINVAL;
 
 	if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
 		/*
@@ -2321,7 +2309,7 @@
 	linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
 	if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
 	    (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1))
-		return IXGBE_ERR_FC_NOT_NEGOTIATED;
+		return -EIO;
 
 	pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
 	pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
@@ -2353,12 +2341,12 @@
 	 */
 	links = IXGBE_READ_REG(hw, IXGBE_LINKS);
 	if ((links & IXGBE_LINKS_KX_AN_COMP) == 0)
-		return IXGBE_ERR_FC_NOT_NEGOTIATED;
+		return -EIO;
 
 	if (hw->mac.type == ixgbe_mac_82599EB) {
 		links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
 		if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0)
-			return IXGBE_ERR_FC_NOT_NEGOTIATED;
+			return -EIO;
 	}
 	/*
 	 * Read the 10g AN autoc and LP ability registers and resolve
@@ -2407,8 +2395,8 @@
  **/
 void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 {
-	s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
 	ixgbe_link_speed speed;
+	s32 ret_val = -EIO;
 	bool link_up;
 
 	/*
@@ -2506,15 +2494,15 @@
 }
 
 /**
- *  ixgbe_disable_pcie_master - Disable PCI-express master access
+ *  ixgbe_disable_pcie_primary - Disable PCI-express primary access
  *  @hw: pointer to hardware structure
  *
- *  Disables PCI-Express master access and verifies there are no pending
- *  requests. IXGBE_ERR_MASTER_REQUESTS_PENDING is returned if master disable
- *  bit hasn't caused the master requests to be disabled, else 0
- *  is returned signifying master requests disabled.
+ *  Disables PCI-Express primary access and verifies there are no pending
+ *  requests. -EALREADY is returned if primary disable
+ *  bit hasn't caused the primary requests to be disabled, else 0
+ *  is returned signifying primary requests disabled.
  **/
-static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw)
+static s32 ixgbe_disable_pcie_primary(struct ixgbe_hw *hw)
 {
 	u32 i, poll;
 	u16 value;
@@ -2523,23 +2511,23 @@
 	IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS);
 
 	/* Poll for bit to read as set */
-	for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) {
+	for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
 		if (IXGBE_READ_REG(hw, IXGBE_CTRL) & IXGBE_CTRL_GIO_DIS)
 			break;
 		usleep_range(100, 120);
 	}
-	if (i >= IXGBE_PCI_MASTER_DISABLE_TIMEOUT) {
+	if (i >= IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT) {
 		hw_dbg(hw, "GIO disable did not set - requesting resets\n");
 		goto gio_disable_fail;
 	}
 
-	/* Exit if master requests are blocked */
+	/* Exit if primary requests are blocked */
 	if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) ||
 	    ixgbe_removed(hw->hw_addr))
 		return 0;
 
-	/* Poll for master request bit to clear */
-	for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) {
+	/* Poll for primary request bit to clear */
+	for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
 		udelay(100);
 		if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
 			return 0;
@@ -2547,13 +2535,13 @@
 
 	/*
 	 * Two consecutive resets are required via CTRL.RST per datasheet
-	 * 5.2.5.3.2 Master Disable.  We set a flag to inform the reset routine
-	 * of this need.  The first reset prevents new master requests from
+	 * 5.2.5.3.2 Primary Disable.  We set a flag to inform the reset routine
+	 * of this need.  The first reset prevents new primary requests from
 	 * being issued by our device.  We then must wait 1usec or more for any
 	 * remaining completions from the PCIe bus to trickle in, and then reset
 	 * again to clear out any effects they may have had on our device.
 	 */
-	hw_dbg(hw, "GIO Master Disable bit didn't clear - requesting resets\n");
+	hw_dbg(hw, "GIO Primary Disable bit didn't clear - requesting resets\n");
 gio_disable_fail:
 	hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
 
@@ -2575,7 +2563,7 @@
 	}
 
 	hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n");
-	return IXGBE_ERR_MASTER_REQUESTS_PENDING;
+	return -EALREADY;
 }
 
 /**
@@ -2600,7 +2588,7 @@
 		 * SW_FW_SYNC bits (not just NVM)
 		 */
 		if (ixgbe_get_eeprom_semaphore(hw))
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 
 		gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
 		if (!(gssr & (fwmask | swmask))) {
@@ -2620,7 +2608,7 @@
 		ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask));
 
 	usleep_range(5000, 10000);
-	return IXGBE_ERR_SWFW_SYNC;
+	return -EBUSY;
 }
 
 /**
@@ -2757,7 +2745,7 @@
 	s32 ret_val;
 
 	if (index > 3)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/*
 	 * Link must be up to auto-blink the LEDs;
@@ -2803,7 +2791,7 @@
 	s32 ret_val;
 
 	if (index > 3)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
 	if (ret_val)
@@ -2963,7 +2951,7 @@
 	/* Make sure we are using a valid rar index range */
 	if (rar >= rar_entries) {
 		hw_dbg(hw, "RAR index %d is out of range.\n", rar);
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
@@ -3014,7 +3002,7 @@
 	/* Make sure we are using a valid rar index range */
 	if (rar >= rar_entries) {
 		hw_dbg(hw, "RAR index %d is out of range.\n", rar);
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	if (vmdq < 32) {
@@ -3091,7 +3079,7 @@
 	 * will simply bypass the VLVF if there are no entries present in the
 	 * VLVF that contain our VLAN
 	 */
-	first_empty_slot = vlvf_bypass ? IXGBE_ERR_NO_SPACE : 0;
+	first_empty_slot = vlvf_bypass ? -ENOSPC : 0;
 
 	/* add VLAN enable bit for comparison */
 	vlan |= IXGBE_VLVF_VIEN;
@@ -3115,7 +3103,7 @@
 	if (!first_empty_slot)
 		hw_dbg(hw, "No space in VLVF.\n");
 
-	return first_empty_slot ? : IXGBE_ERR_NO_SPACE;
+	return first_empty_slot ? : -ENOSPC;
 }
 
 /**
@@ -3135,7 +3123,7 @@
 	s32 vlvf_index;
 
 	if ((vlan > 4095) || (vind > 63))
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/*
 	 * this is a 2 part operation - first the VFTA, then the
@@ -3596,7 +3584,8 @@
  *
  *  Communicates with the manageability block. On success return 0
  *  else returns semaphore error when encountering an error acquiring
- *  semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ *  semaphore, -EINVAL when incorrect parameters passed or -EIO when
+ *  command fails.
  *
  *  This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
  *  by the caller.
@@ -3609,7 +3598,7 @@
 
 	if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
 		hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
-		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+		return -EINVAL;
 	}
 
 	/* Set bit 9 of FWSTS clearing FW reset indication */
@@ -3620,13 +3609,13 @@
 	hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
 	if (!(hicr & IXGBE_HICR_EN)) {
 		hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
-		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+		return -EIO;
 	}
 
 	/* Calculate length in DWORDs. We must be DWORD aligned */
 	if (length % sizeof(u32)) {
 		hw_dbg(hw, "Buffer length failure, not aligned to dword");
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 	}
 
 	dword_len = length >> 2;
@@ -3651,7 +3640,7 @@
 	/* Check command successful completion. */
 	if ((timeout && i == timeout) ||
 	    !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
-		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+		return -EIO;
 
 	return 0;
 }
@@ -3671,7 +3660,7 @@
  *  in these cases.
  *
  *  Communicates with the manageability block.  On success return 0
- *  else return IXGBE_ERR_HOST_INTERFACE_COMMAND.
+ *  else return -EIO or -EINVAL.
  **/
 s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
 				 u32 length, u32 timeout,
@@ -3686,7 +3675,7 @@
 
 	if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
 		hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
-		return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+		return -EINVAL;
 	}
 	/* Take management host interface semaphore */
 	status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
@@ -3716,7 +3705,7 @@
 
 	if (length < round_up(buf_len, 4) + hdr_size) {
 		hw_dbg(hw, "Buffer not large enough for reply message.\n");
-		status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
+		status = -EIO;
 		goto rel_out;
 	}
 
@@ -3747,8 +3736,8 @@
  *
  *  Sends driver version number to firmware through the manageability
  *  block.  On success return 0
- *  else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring
- *  semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ *  else returns -EBUSY when encountering an error acquiring
+ *  semaphore or -EIO when command fails.
  **/
 s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
 				 u8 build, u8 sub, __always_unused u16 len,
@@ -3784,7 +3773,7 @@
 		    FW_CEM_RESP_STATUS_SUCCESS)
 			ret_val = 0;
 		else
-			ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND;
+			ret_val = -EIO;
 
 		break;
 	}
@@ -3882,14 +3871,14 @@
 		return status;
 
 	if ((*ets_offset == 0x0000) || (*ets_offset == 0xFFFF))
-		return IXGBE_NOT_IMPLEMENTED;
+		return -EOPNOTSUPP;
 
 	status = hw->eeprom.ops.read(hw, *ets_offset, ets_cfg);
 	if (status)
 		return status;
 
 	if ((*ets_cfg & IXGBE_ETS_TYPE_MASK) != IXGBE_ETS_TYPE_EMC_SHIFTED)
-		return IXGBE_NOT_IMPLEMENTED;
+		return -EOPNOTSUPP;
 
 	return 0;
 }
@@ -3912,7 +3901,7 @@
 
 	/* Only support thermal sensors attached to physical port 0 */
 	if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
-		return IXGBE_NOT_IMPLEMENTED;
+		return -EOPNOTSUPP;
 
 	status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
 	if (status)
@@ -3972,7 +3961,7 @@
 
 	/* Only support thermal sensors attached to physical port 0 */
 	if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
-		return IXGBE_NOT_IMPLEMENTED;
+		return -EOPNOTSUPP;
 
 	status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
 	if (status)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -138,6 +138,8 @@
 	"legacy-rx",
 #define IXGBE_PRIV_FLAGS_VF_IPSEC_EN	BIT(1)
 	"vf-ipsec",
+#define IXGBE_PRIV_FLAGS_AUTO_DISABLE_VF	BIT(2)
+	"mdd-disable-vf",
 };
 
 #define IXGBE_PRIV_FLAGS_STR_LEN ARRAY_SIZE(ixgbe_priv_flags_strings)
@@ -2633,6 +2635,14 @@
 	return 0;
 }
 
+static int ixgbe_rss_indir_tbl_max(struct ixgbe_adapter *adapter)
+{
+	if (adapter->hw.mac.type < ixgbe_mac_X550)
+		return 16;
+	else
+		return 64;
+}
+
 static int ixgbe_get_rxnfc(struct net_device *dev, struct ethtool_rxnfc *cmd,
 			   u32 *rule_locs)
 {
@@ -2641,7 +2651,8 @@
 
 	switch (cmd->cmd) {
 	case ETHTOOL_GRXRINGS:
-		cmd->data = adapter->num_rx_queues;
+		cmd->data = min_t(int, adapter->num_rx_queues,
+				  ixgbe_rss_indir_tbl_max(adapter));
 		ret = 0;
 		break;
 	case ETHTOOL_GRXCLSRLCNT:
@@ -3043,14 +3054,6 @@
 	return ret;
 }
 
-static int ixgbe_rss_indir_tbl_max(struct ixgbe_adapter *adapter)
-{
-	if (adapter->hw.mac.type < ixgbe_mac_X550)
-		return 16;
-	else
-		return 64;
-}
-
 static u32 ixgbe_get_rxfh_key_size(struct net_device *netdev)
 {
 	return IXGBE_RSS_KEY_SIZE;
@@ -3099,8 +3102,8 @@
 	int i;
 	u32 reta_entries = ixgbe_rss_indir_tbl_entries(adapter);
 
-	if (hfunc)
-		return -EINVAL;
+	if (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc != ETH_RSS_HASH_TOP)
+		return -EOPNOTSUPP;
 
 	/* Fill out the redirection table */
 	if (indir) {
@@ -3337,7 +3340,7 @@
 {
 	struct ixgbe_adapter *adapter = netdev_priv(dev);
 	struct ixgbe_hw *hw = &adapter->hw;
-	s32 status = IXGBE_ERR_PHY_ADDR_INVALID;
+	s32 status = -EFAULT;
 	u8 databyte = 0xFF;
 	int i = 0;
 
@@ -3507,6 +3510,9 @@
 	if (adapter->flags2 & IXGBE_FLAG2_VF_IPSEC_ENABLED)
 		priv_flags |= IXGBE_PRIV_FLAGS_VF_IPSEC_EN;
 
+	if (adapter->flags2 & IXGBE_FLAG2_AUTO_DISABLE_VF)
+		priv_flags |= IXGBE_PRIV_FLAGS_AUTO_DISABLE_VF;
+
 	return priv_flags;
 }
 
@@ -3514,6 +3520,7 @@
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 	unsigned int flags2 = adapter->flags2;
+	unsigned int i;
 
 	flags2 &= ~IXGBE_FLAG2_RX_LEGACY;
 	if (priv_flags & IXGBE_PRIV_FLAGS_LEGACY_RX)
@@ -3523,6 +3530,21 @@
 	if (priv_flags & IXGBE_PRIV_FLAGS_VF_IPSEC_EN)
 		flags2 |= IXGBE_FLAG2_VF_IPSEC_ENABLED;
 
+	flags2 &= ~IXGBE_FLAG2_AUTO_DISABLE_VF;
+	if (priv_flags & IXGBE_PRIV_FLAGS_AUTO_DISABLE_VF) {
+		if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
+			/* Reset primary abort counter */
+			for (i = 0; i < adapter->num_vfs; i++)
+				adapter->vfinfo[i].primary_abort_count = 0;
+
+			flags2 |= IXGBE_FLAG2_AUTO_DISABLE_VF;
+		} else {
+			e_info(probe,
+			       "Cannot set private flags: Operation not supported\n");
+			return -EOPNOTSUPP;
+		}
+	}
+
 	if (flags2 != adapter->flags2) {
 		adapter->flags2 = flags2;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
@@ -903,12 +903,19 @@
 	/* Tx IPsec offload doesn't seem to work on this
 	 * device, so block these requests for now.
 	 */
-	if (!(sam->flags & XFRM_OFFLOAD_INBOUND)) {
+	sam->flags = sam->flags & ~XFRM_OFFLOAD_IPV6;
+	if (sam->flags != XFRM_OFFLOAD_INBOUND) {
 		err = -EOPNOTSUPP;
 		goto err_out;
 	}
 
-	xs = kzalloc(sizeof(*xs), GFP_KERNEL);
+	algo = xfrm_aead_get_byname(aes_gcm_name, IXGBE_IPSEC_AUTH_BITS, 1);
+	if (unlikely(!algo)) {
+		err = -ENOENT;
+		goto err_out;
+	}
+
+	xs = kzalloc(sizeof(*xs), GFP_ATOMIC);
 	if (unlikely(!xs)) {
 		err = -ENOMEM;
 		goto err_out;
@@ -924,14 +931,8 @@
 		memcpy(&xs->id.daddr.a4, sam->addr, sizeof(xs->id.daddr.a4));
 	xs->xso.dev = adapter->netdev;
 
-	algo = xfrm_aead_get_byname(aes_gcm_name, IXGBE_IPSEC_AUTH_BITS, 1);
-	if (unlikely(!algo)) {
-		err = -ENOENT;
-		goto err_xs;
-	}
-
 	aead_len = sizeof(*xs->aead) + IXGBE_IPSEC_KEY_BITS / 8;
-	xs->aead = kzalloc(aead_len, GFP_KERNEL);
+	xs->aead = kzalloc(aead_len, GFP_ATOMIC);
 	if (unlikely(!xs->aead)) {
 		err = -ENOMEM;
 		goto err_xs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -2758,7 +2758,6 @@
 {
 	struct ixgbe_hw *hw = &adapter->hw;
 	u32 eicr = adapter->interrupt_event;
-	s32 rc;
 
 	if (test_bit(__IXGBE_DOWN, &adapter->state))
 		return;
@@ -2792,14 +2791,13 @@
 		}
 
 		/* Check if this is not due to overtemp */
-		if (hw->phy.ops.check_overtemp(hw) != IXGBE_ERR_OVERTEMP)
+		if (!hw->phy.ops.check_overtemp(hw))
 			return;
 
 		break;
 	case IXGBE_DEV_ID_X550EM_A_1G_T:
 	case IXGBE_DEV_ID_X550EM_A_1G_T_L:
-		rc = hw->phy.ops.check_overtemp(hw);
-		if (rc != IXGBE_ERR_OVERTEMP)
+		if (!hw->phy.ops.check_overtemp(hw))
 			return;
 		break;
 	default:
@@ -2943,8 +2941,8 @@
 static inline void ixgbe_irq_enable_queues(struct ixgbe_adapter *adapter,
 					   u64 qmask)
 {
-	u32 mask;
 	struct ixgbe_hw *hw = &adapter->hw;
+	u32 mask;
 
 	switch (hw->mac.type) {
 	case ixgbe_mac_82598EB:
@@ -5514,7 +5512,7 @@
 {
 	u32 speed;
 	bool autoneg, link_up = false;
-	int ret = IXGBE_ERR_LINK_SETUP;
+	int ret = -EIO;
 
 	if (hw->mac.ops.check_link)
 		ret = hw->mac.ops.check_link(hw, &speed, &link_up, false);
@@ -5526,6 +5524,10 @@
 	if (!speed && hw->mac.ops.get_link_capabilities) {
 		ret = hw->mac.ops.get_link_capabilities(hw, &speed,
 							&autoneg);
+		/* remove NBASE-T speeds from default autonegotiation
+		 * to accommodate broken network switches in the field
+		 * which cannot cope with advertised NBASE-T speeds
+		 */
 		speed &= ~(IXGBE_LINK_SPEED_5GB_FULL |
 			   IXGBE_LINK_SPEED_2_5GB_FULL);
 	}
@@ -5678,6 +5680,9 @@
 	ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT);
 	ctrl_ext |= IXGBE_CTRL_EXT_PFRSTD;
 	IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext);
+
+	/* update setting rx tx for all active vfs */
+	ixgbe_set_all_vfs(adapter);
 }
 
 void ixgbe_reinit_locked(struct ixgbe_adapter *adapter)
@@ -5936,13 +5941,13 @@
 	err = hw->mac.ops.init_hw(hw);
 	switch (err) {
 	case 0:
-	case IXGBE_ERR_SFP_NOT_PRESENT:
-	case IXGBE_ERR_SFP_NOT_SUPPORTED:
+	case -ENOENT:
+	case -EOPNOTSUPP:
 		break;
-	case IXGBE_ERR_MASTER_REQUESTS_PENDING:
-		e_dev_err("master disable timed out\n");
+	case -EALREADY:
+		e_dev_err("primary disable timed out\n");
 		break;
-	case IXGBE_ERR_EEPROM_VERSION:
+	case -EACCES:
 		/* We are running on a pre-production device, log a warning */
 		e_dev_warn("This device is a pre-production adapter/LOM. "
 			   "Please be aware there may be issues associated with "
@@ -6135,11 +6140,8 @@
 		for (i = 0 ; i < adapter->num_vfs; i++)
 			adapter->vfinfo[i].clear_to_send = false;
 
-		/* ping all the active vfs to let them know we are going down */
-		ixgbe_ping_all_vfs(adapter);
-
-		/* Disable all VFTE/VFRE TX/RX */
-		ixgbe_disable_tx_rx(adapter);
+		/* update setting rx tx for all active vfs */
+		ixgbe_set_all_vfs(adapter);
 	}
 
 	/* disable transmits in the hardware now that interrupts are off */
@@ -6393,6 +6395,9 @@
 	/* n-tuple support exists, always init our spinlock */
 	spin_lock_init(&adapter->fdir_perfect_lock);
 
+	/* init spinlock to avoid concurrency of VF resources */
+	spin_lock_init(&adapter->vfs_lock);
+
 #ifdef CONFIG_IXGBE_DCB
 	ixgbe_init_dcb(adapter);
 #endif
@@ -6723,6 +6728,18 @@
 }
 
 /**
+ * ixgbe_max_xdp_frame_size - returns the maximum allowed frame size for XDP
+ * @adapter: device handle, pointer to adapter
+ */
+static int ixgbe_max_xdp_frame_size(struct ixgbe_adapter *adapter)
+{
+	if (PAGE_SIZE >= 8192 || adapter->flags2 & IXGBE_FLAG2_RX_LEGACY)
+		return IXGBE_RXBUFFER_2K;
+	else
+		return IXGBE_RXBUFFER_3K;
+}
+
+/**
  * ixgbe_change_mtu - Change the Maximum Transfer Unit
  * @netdev: network interface device structure
  * @new_mtu: new value for maximum frame size
@@ -6733,18 +6750,12 @@
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 
-	if (adapter->xdp_prog) {
-		int new_frame_size = new_mtu + ETH_HLEN + ETH_FCS_LEN +
-				     VLAN_HLEN;
-		int i;
-
-		for (i = 0; i < adapter->num_rx_queues; i++) {
-			struct ixgbe_ring *ring = adapter->rx_ring[i];
+	if (ixgbe_enabled_xdp_adapter(adapter)) {
+		int new_frame_size = new_mtu + IXGBE_PKT_HDR_PAD;
 
-			if (new_frame_size > ixgbe_rx_bufsz(ring)) {
-				e_warn(probe, "Requested MTU size is not supported with XDP\n");
-				return -EINVAL;
-			}
+		if (new_frame_size > ixgbe_max_xdp_frame_size(adapter)) {
+			e_warn(probe, "Requested MTU size is not supported with XDP\n");
+			return -EINVAL;
 		}
 	}
 
@@ -7604,6 +7615,27 @@
 }
 
 #ifdef CONFIG_PCI_IOV
+static void ixgbe_bad_vf_abort(struct ixgbe_adapter *adapter, u32 vf)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+
+	if (adapter->hw.mac.type == ixgbe_mac_82599EB &&
+	    adapter->flags2 & IXGBE_FLAG2_AUTO_DISABLE_VF) {
+		adapter->vfinfo[vf].primary_abort_count++;
+		if (adapter->vfinfo[vf].primary_abort_count ==
+		    IXGBE_PRIMARY_ABORT_LIMIT) {
+			ixgbe_set_vf_link_state(adapter, vf,
+						IFLA_VF_LINK_STATE_DISABLE);
+			adapter->vfinfo[vf].primary_abort_count = 0;
+
+			e_info(drv,
+			       "Malicious Driver Detection event detected on PF %d VF %d MAC: %pM mdd-disable-vf=on",
+			       hw->bus.func, vf,
+			       adapter->vfinfo[vf].vf_mac_addresses);
+		}
+	}
+}
+
 static void ixgbe_check_for_bad_vf(struct ixgbe_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
@@ -7635,8 +7667,10 @@
 			continue;
 		pci_read_config_word(vfdev, PCI_STATUS, &status_reg);
 		if (status_reg != IXGBE_FAILED_READ_CFG_WORD &&
-		    status_reg & PCI_STATUS_REC_MASTER_ABORT)
+		    status_reg & PCI_STATUS_REC_MASTER_ABORT) {
+			ixgbe_bad_vf_abort(adapter, vf);
 			pcie_flr(vfdev);
+		}
 	}
 }
 
@@ -7723,10 +7757,10 @@
 	adapter->sfp_poll_time = jiffies + IXGBE_SFP_POLL_JIFFIES - 1;
 
 	err = hw->phy.ops.identify_sfp(hw);
-	if (err == IXGBE_ERR_SFP_NOT_SUPPORTED)
+	if (err == -EOPNOTSUPP)
 		goto sfp_out;
 
-	if (err == IXGBE_ERR_SFP_NOT_PRESENT) {
+	if (err == -ENOENT) {
 		/* If no cable is present, then we need to reset
 		 * the next time we find a good cable. */
 		adapter->flags2 |= IXGBE_FLAG2_SFP_NEEDS_RESET;
@@ -7752,7 +7786,7 @@
 	else
 		err = hw->mac.ops.setup_sfp(hw);
 
-	if (err == IXGBE_ERR_SFP_NOT_SUPPORTED)
+	if (err == -EOPNOTSUPP)
 		goto sfp_out;
 
 	adapter->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
@@ -7761,8 +7795,8 @@
 sfp_out:
 	clear_bit(__IXGBE_IN_SFP_INIT, &adapter->state);
 
-	if ((err == IXGBE_ERR_SFP_NOT_SUPPORTED) &&
-	    (adapter->netdev->reg_state == NETREG_REGISTERED)) {
+	if (err == -EOPNOTSUPP &&
+	    adapter->netdev->reg_state == NETREG_REGISTERED) {
 		e_dev_err("failed to initialize because an unsupported "
 			  "SFP+ module type was detected.\n");
 		e_dev_err("Reload the driver after installing a "
@@ -7832,7 +7866,7 @@
 static void ixgbe_phy_interrupt_subtask(struct ixgbe_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
-	u32 status;
+	bool overtemp;
 
 	if (!(adapter->flags2 & IXGBE_FLAG2_PHY_INTERRUPT))
 		return;
@@ -7842,11 +7876,9 @@
 	if (!hw->phy.ops.handle_lasi)
 		return;
 
-	status = hw->phy.ops.handle_lasi(&adapter->hw);
-	if (status != IXGBE_ERR_OVERTEMP)
-		return;
-
-	e_crit(drv, "%s\n", ixgbe_overheat_msg);
+	hw->phy.ops.handle_lasi(&adapter->hw, &overtemp);
+	if (overtemp)
+		e_crit(drv, "%s\n", ixgbe_overheat_msg);
 }
 
 static void ixgbe_reset_subtask(struct ixgbe_adapter *adapter)
@@ -8385,7 +8417,7 @@
 		struct ixgbe_adapter *adapter = q_vector->adapter;
 
 		if (unlikely(skb_tail_pointer(skb) < hdr.network +
-			     VXLAN_HEADROOM))
+			     vxlan_headroom(0)))
 			return;
 
 		/* verify the port is recognized as VXLAN */
@@ -8683,7 +8715,7 @@
 
 			if (skb_cow_head(skb, 0))
 				goto out_drop;
-			vhdr = (struct vlan_ethhdr *)skb->data;
+			vhdr = skb_vlan_eth_hdr(skb);
 			vhdr->h_vlan_TCI = htons(tx_flags >>
 						 IXGBE_TX_FLAGS_VLAN_SHIFT);
 		} else {
@@ -10256,6 +10288,7 @@
 	.ndo_set_vf_vlan	= ixgbe_ndo_set_vf_vlan,
 	.ndo_set_vf_rate	= ixgbe_ndo_set_vf_bw,
 	.ndo_set_vf_spoofchk	= ixgbe_ndo_set_vf_spoofchk,
+	.ndo_set_vf_link_state	= ixgbe_ndo_set_vf_link_state,
 	.ndo_set_vf_rss_query_en = ixgbe_ndo_set_vf_rss_query_en,
 	.ndo_set_vf_trust	= ixgbe_ndo_set_vf_trust,
 	.ndo_get_vf_config	= ixgbe_ndo_get_vf_config,
@@ -10372,6 +10405,44 @@
 }
 
 /**
+ * ixgbe_irq_disable_single - Disable single IRQ vector
+ * @adapter: adapter structure
+ * @ring: ring index
+ **/
+static void ixgbe_irq_disable_single(struct ixgbe_adapter *adapter, u32 ring)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+	u64 qmask = BIT_ULL(ring);
+	u32 mask;
+
+	switch (adapter->hw.mac.type) {
+	case ixgbe_mac_82598EB:
+		mask = qmask & IXGBE_EIMC_RTX_QUEUE;
+		IXGBE_WRITE_REG(&adapter->hw, IXGBE_EIMC, mask);
+		break;
+	case ixgbe_mac_82599EB:
+	case ixgbe_mac_X540:
+	case ixgbe_mac_X550:
+	case ixgbe_mac_X550EM_x:
+	case ixgbe_mac_x550em_a:
+		mask = (qmask & 0xFFFFFFFF);
+		if (mask)
+			IXGBE_WRITE_REG(hw, IXGBE_EIMS_EX(0), mask);
+		mask = (qmask >> 32);
+		if (mask)
+			IXGBE_WRITE_REG(hw, IXGBE_EIMS_EX(1), mask);
+		break;
+	default:
+		break;
+	}
+	IXGBE_WRITE_FLUSH(&adapter->hw);
+	if (adapter->flags & IXGBE_FLAG_MSIX_ENABLED)
+		synchronize_irq(adapter->msix_entries[ring].vector);
+	else
+		synchronize_irq(adapter->pdev->irq);
+}
+
+/**
  * ixgbe_txrx_ring_disable - Disable Rx/Tx/XDP Tx rings
  * @adapter: adapter structure
  * @ring: ring index
@@ -10387,6 +10458,11 @@
 	tx_ring = adapter->tx_ring[ring];
 	xdp_ring = adapter->xdp_ring[ring];
 
+	ixgbe_irq_disable_single(adapter, ring);
+
+	/* Rx/Tx/XDP Tx share the same napi context. */
+	napi_disable(&rx_ring->q_vector->napi);
+
 	ixgbe_disable_txr(adapter, tx_ring);
 	if (xdp_ring)
 		ixgbe_disable_txr(adapter, xdp_ring);
@@ -10395,9 +10471,6 @@
 	if (xdp_ring)
 		synchronize_rcu();
 
-	/* Rx/Tx/XDP Tx share the same napi context. */
-	napi_disable(&rx_ring->q_vector->napi);
-
 	ixgbe_clean_tx_ring(tx_ring);
 	if (xdp_ring)
 		ixgbe_clean_tx_ring(xdp_ring);
@@ -10425,9 +10498,6 @@
 	tx_ring = adapter->tx_ring[ring];
 	xdp_ring = adapter->xdp_ring[ring];
 
-	/* Rx/Tx/XDP Tx share the same napi context. */
-	napi_enable(&rx_ring->q_vector->napi);
-
 	ixgbe_configure_tx_ring(adapter, tx_ring);
 	if (xdp_ring)
 		ixgbe_configure_tx_ring(adapter, xdp_ring);
@@ -10436,6 +10506,11 @@
 	clear_bit(__IXGBE_TX_DISABLED, &tx_ring->state);
 	if (xdp_ring)
 		clear_bit(__IXGBE_TX_DISABLED, &xdp_ring->state);
+
+	/* Rx/Tx/XDP Tx share the same napi context. */
+	napi_enable(&rx_ring->q_vector->napi);
+	ixgbe_irq_enable_queues(adapter, BIT_ULL(ring));
+	IXGBE_WRITE_FLUSH(&adapter->hw);
 }
 
 /**
@@ -10722,6 +10797,9 @@
 	if (err)
 		goto err_sw_init;
 
+	if (adapter->hw.mac.type == ixgbe_mac_82599EB)
+		adapter->flags2 |= IXGBE_FLAG2_AUTO_DISABLE_VF;
+
 	switch (adapter->hw.mac.type) {
 	case ixgbe_mac_X550:
 	case ixgbe_mac_X550EM_x:
@@ -10769,9 +10847,9 @@
 	err = hw->mac.ops.reset_hw(hw);
 	hw->phy.reset_if_overtemp = false;
 	ixgbe_set_eee_capable(adapter);
-	if (err == IXGBE_ERR_SFP_NOT_PRESENT) {
+	if (err == -ENOENT) {
 		err = 0;
-	} else if (err == IXGBE_ERR_SFP_NOT_SUPPORTED) {
+	} else if (err == -EOPNOTSUPP) {
 		e_dev_err("failed to load because an unsupported SFP+ or QSFP module type was detected.\n");
 		e_dev_err("Reload the driver after installing a supported module.\n");
 		goto err_sw_init;
@@ -10988,7 +11066,7 @@
 
 	/* reset the hardware with the new settings */
 	err = hw->mac.ops.start_hw(hw);
-	if (err == IXGBE_ERR_EEPROM_VERSION) {
+	if (err == -EACCES) {
 		/* We are running on a pre-production device, log a warning */
 		e_dev_warn("This device is a pre-production adapter/LOM. "
 			   "Please be aware there may be issues associated "
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.c
@@ -24,7 +24,7 @@
 		size = mbx->size;
 
 	if (!mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	return mbx->ops->read(hw, msg, size, mbx_id);
 }
@@ -43,10 +43,10 @@
 	struct ixgbe_mbx_info *mbx = &hw->mbx;
 
 	if (size > mbx->size)
-		return IXGBE_ERR_MBX;
+		return -EINVAL;
 
 	if (!mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	return mbx->ops->write(hw, msg, size, mbx_id);
 }
@@ -63,7 +63,7 @@
 	struct ixgbe_mbx_info *mbx = &hw->mbx;
 
 	if (!mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	return mbx->ops->check_for_msg(hw, mbx_id);
 }
@@ -80,7 +80,7 @@
 	struct ixgbe_mbx_info *mbx = &hw->mbx;
 
 	if (!mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	return mbx->ops->check_for_ack(hw, mbx_id);
 }
@@ -97,7 +97,7 @@
 	struct ixgbe_mbx_info *mbx = &hw->mbx;
 
 	if (!mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	return mbx->ops->check_for_rst(hw, mbx_id);
 }
@@ -115,12 +115,12 @@
 	int countdown = mbx->timeout;
 
 	if (!countdown || !mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	while (mbx->ops->check_for_msg(hw, mbx_id)) {
 		countdown--;
 		if (!countdown)
-			return IXGBE_ERR_MBX;
+			return -EIO;
 		udelay(mbx->usec_delay);
 	}
 
@@ -140,12 +140,12 @@
 	int countdown = mbx->timeout;
 
 	if (!countdown || !mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	while (mbx->ops->check_for_ack(hw, mbx_id)) {
 		countdown--;
 		if (!countdown)
-			return IXGBE_ERR_MBX;
+			return -EIO;
 		udelay(mbx->usec_delay);
 	}
 
@@ -169,7 +169,7 @@
 	s32 ret_val;
 
 	if (!mbx->ops)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	ret_val = ixgbe_poll_for_msg(hw, mbx_id);
 	if (ret_val)
@@ -197,7 +197,7 @@
 
 	/* exit if either we can't write or there isn't a defined timeout */
 	if (!mbx->ops || !mbx->timeout)
-		return IXGBE_ERR_MBX;
+		return -EIO;
 
 	/* send msg */
 	ret_val = mbx->ops->write(hw, msg, size, mbx_id);
@@ -217,7 +217,7 @@
 		return 0;
 	}
 
-	return IXGBE_ERR_MBX;
+	return -EIO;
 }
 
 /**
@@ -238,7 +238,7 @@
 		return 0;
 	}
 
-	return IXGBE_ERR_MBX;
+	return -EIO;
 }
 
 /**
@@ -259,7 +259,7 @@
 		return 0;
 	}
 
-	return IXGBE_ERR_MBX;
+	return -EIO;
 }
 
 /**
@@ -295,7 +295,7 @@
 		return 0;
 	}
 
-	return IXGBE_ERR_MBX;
+	return -EIO;
 }
 
 /**
@@ -317,7 +317,7 @@
 	if (p2v_mailbox & IXGBE_PFMAILBOX_PFU)
 		return 0;
 
-	return IXGBE_ERR_MBX;
+	return -EIO;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h
@@ -7,7 +7,6 @@
 #include "ixgbe_type.h"
 
 #define IXGBE_VFMAILBOX_SIZE        16 /* 16 32 bit words - 64 bytes */
-#define IXGBE_ERR_MBX               -100
 
 #define IXGBE_VFMAILBOX             0x002FC
 #define IXGBE_VFMBMEM               0x00200
@@ -85,6 +84,8 @@
 #define IXGBE_VF_IPSEC_ADD	0x0d
 #define IXGBE_VF_IPSEC_DEL	0x0e
 
+#define IXGBE_VF_GET_LINK_STATE 0x10 /* get vf link state */
+
 /* length of permanent address message returned from PF */
 #define IXGBE_VF_PERMADDR_MSG_LEN 4
 /* word in permanent address message with the current multicast type */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -102,7 +102,7 @@
 	csum = ~csum;
 	do {
 		if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask))
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 		ixgbe_i2c_start(hw);
 		/* Device Address and write indication */
 		if (ixgbe_out_i2c_byte_ack(hw, addr))
@@ -150,7 +150,7 @@
 			hw_dbg(hw, "I2C byte read combined error.\n");
 	} while (retry < max_retry);
 
-	return IXGBE_ERR_I2C;
+	return -EIO;
 }
 
 /**
@@ -179,7 +179,7 @@
 	csum = ~csum;
 	do {
 		if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask))
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 		ixgbe_i2c_start(hw);
 		/* Device Address and write indication */
 		if (ixgbe_out_i2c_byte_ack(hw, addr))
@@ -215,7 +215,7 @@
 			hw_dbg(hw, "I2C byte write combined error.\n");
 	} while (retry < max_retry);
 
-	return IXGBE_ERR_I2C;
+	return -EIO;
 }
 
 /**
@@ -262,8 +262,8 @@
  **/
 s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw)
 {
+	u32 status = -EFAULT;
 	u32 phy_addr;
-	u32 status = IXGBE_ERR_PHY_ADDR_INVALID;
 
 	if (!hw->phy.phy_semaphore_mask) {
 		if (hw->bus.lan_id)
@@ -282,7 +282,7 @@
 		if (ixgbe_probe_phy(hw, phy_addr))
 			return 0;
 		else
-			return IXGBE_ERR_PHY_ADDR_INVALID;
+			return -EFAULT;
 	}
 
 	for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) {
@@ -408,8 +408,7 @@
 		return status;
 
 	/* Don't reset PHY if it's shut down due to overtemp. */
-	if (!hw->phy.reset_if_overtemp &&
-	    (IXGBE_ERR_OVERTEMP == hw->phy.ops.check_overtemp(hw)))
+	if (!hw->phy.reset_if_overtemp && hw->phy.ops.check_overtemp(hw))
 		return 0;
 
 	/* Blocked by MNG FW so bail */
@@ -457,7 +456,7 @@
 
 	if (ctrl & MDIO_CTRL1_RESET) {
 		hw_dbg(hw, "PHY reset polling failed to complete.\n");
-		return IXGBE_ERR_RESET_FAILED;
+		return -EIO;
 	}
 
 	return 0;
@@ -500,7 +499,7 @@
 
 	if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) {
 		hw_dbg(hw, "PHY address command did not complete.\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	/* Address cycle complete, setup and write the read
@@ -527,7 +526,7 @@
 
 	if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) {
 		hw_dbg(hw, "PHY read command didn't complete\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	/* Read operation is complete.  Get the data
@@ -559,7 +558,7 @@
 						phy_data);
 		hw->mac.ops.release_swfw_sync(hw, gssr);
 	} else {
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 	}
 
 	return status;
@@ -604,7 +603,7 @@
 
 	if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) {
 		hw_dbg(hw, "PHY address cmd didn't complete\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	/*
@@ -632,7 +631,7 @@
 
 	if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) {
 		hw_dbg(hw, "PHY write cmd didn't complete\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	return 0;
@@ -657,7 +656,7 @@
 						 phy_data);
 		hw->mac.ops.release_swfw_sync(hw, gssr);
 	} else {
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 	}
 
 	return status;
@@ -855,9 +854,11 @@
 	rp_pdev = pci_get_domain_bus_and_slot(0, 0, devfn);
 	if (rp_pdev && rp_pdev->subordinate) {
 		bus = rp_pdev->subordinate->number;
+		pci_dev_put(rp_pdev);
 		return pci_get_domain_bus_and_slot(0, bus, 0);
 	}
 
+	pci_dev_put(rp_pdev);
 	return NULL;
 }
 
@@ -874,6 +875,7 @@
 	struct ixgbe_adapter *adapter = hw->back;
 	struct pci_dev *pdev = adapter->pdev;
 	struct pci_dev *func0_pdev;
+	bool has_mii = false;
 
 	/* For the C3000 family of SoCs (x550em_a) the internal ixgbe devices
 	 * are always downstream of root ports @ 0000:00:16.0 & 0000:00:17.0
@@ -884,15 +886,16 @@
 	func0_pdev = ixgbe_get_first_secondary_devfn(PCI_DEVFN(0x16, 0));
 	if (func0_pdev) {
 		if (func0_pdev == pdev)
-			return true;
-		else
-			return false;
+			has_mii = true;
+		goto out;
 	}
 	func0_pdev = ixgbe_get_first_secondary_devfn(PCI_DEVFN(0x17, 0));
 	if (func0_pdev == pdev)
-		return true;
+		has_mii = true;
 
-	return false;
+out:
+	pci_dev_put(func0_pdev);
+	return has_mii;
 }
 
 /**
@@ -1299,7 +1302,7 @@
 
 	if ((phy_data & MDIO_CTRL1_RESET) != 0) {
 		hw_dbg(hw, "PHY reset did not complete.\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	/* Get init offsets */
@@ -1356,12 +1359,12 @@
 				hw_dbg(hw, "SOL\n");
 			} else {
 				hw_dbg(hw, "Bad control value\n");
-				return IXGBE_ERR_PHY;
+				return -EIO;
 			}
 			break;
 		default:
 			hw_dbg(hw, "Bad control type\n");
-			return IXGBE_ERR_PHY;
+			return -EIO;
 		}
 	}
 
@@ -1369,7 +1372,7 @@
 
 err_eeprom:
 	hw_err(hw, "eeprom read at offset %d failed\n", data_offset);
-	return IXGBE_ERR_PHY;
+	return -EIO;
 }
 
 /**
@@ -1387,10 +1390,10 @@
 		return ixgbe_identify_qsfp_module_generic(hw);
 	default:
 		hw->phy.sfp_type = ixgbe_sfp_type_not_present;
-		return IXGBE_ERR_SFP_NOT_PRESENT;
+		return -ENOENT;
 	}
 
-	return IXGBE_ERR_SFP_NOT_PRESENT;
+	return -ENOENT;
 }
 
 /**
@@ -1415,7 +1418,7 @@
 
 	if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber) {
 		hw->phy.sfp_type = ixgbe_sfp_type_not_present;
-		return IXGBE_ERR_SFP_NOT_PRESENT;
+		return -ENOENT;
 	}
 
 	/* LAN ID is needed for sfp_type determination */
@@ -1430,7 +1433,7 @@
 
 	if (identifier != IXGBE_SFF_IDENTIFIER_SFP) {
 		hw->phy.type = ixgbe_phy_sfp_unsupported;
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 	status = hw->phy.ops.read_i2c_eeprom(hw,
 					     IXGBE_SFF_1GBE_COMP_CODES,
@@ -1621,7 +1624,7 @@
 	      hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
 	      hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1)) {
 		hw->phy.type = ixgbe_phy_sfp_unsupported;
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 
 	/* Anything else 82598-based is supported */
@@ -1645,7 +1648,7 @@
 		}
 		hw_dbg(hw, "SFP+ module not supported\n");
 		hw->phy.type = ixgbe_phy_sfp_unsupported;
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 	return 0;
 
@@ -1655,7 +1658,7 @@
 		hw->phy.id = 0;
 		hw->phy.type = ixgbe_phy_unknown;
 	}
-	return IXGBE_ERR_SFP_NOT_PRESENT;
+	return -ENOENT;
 }
 
 /**
@@ -1682,7 +1685,7 @@
 
 	if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber_qsfp) {
 		hw->phy.sfp_type = ixgbe_sfp_type_not_present;
-		return IXGBE_ERR_SFP_NOT_PRESENT;
+		return -ENOENT;
 	}
 
 	/* LAN ID is needed for sfp_type determination */
@@ -1696,7 +1699,7 @@
 
 	if (identifier != IXGBE_SFF_IDENTIFIER_QSFP_PLUS) {
 		hw->phy.type = ixgbe_phy_sfp_unsupported;
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 
 	hw->phy.id = identifier;
@@ -1764,7 +1767,7 @@
 		} else {
 			/* unsupported module type */
 			hw->phy.type = ixgbe_phy_sfp_unsupported;
-			return IXGBE_ERR_SFP_NOT_SUPPORTED;
+			return -EOPNOTSUPP;
 		}
 	}
 
@@ -1824,7 +1827,7 @@
 			}
 			hw_dbg(hw, "QSFP module not supported\n");
 			hw->phy.type = ixgbe_phy_sfp_unsupported;
-			return IXGBE_ERR_SFP_NOT_SUPPORTED;
+			return -EOPNOTSUPP;
 		}
 		return 0;
 	}
@@ -1835,7 +1838,7 @@
 	hw->phy.id = 0;
 	hw->phy.type = ixgbe_phy_unknown;
 
-	return IXGBE_ERR_SFP_NOT_PRESENT;
+	return -ENOENT;
 }
 
 /**
@@ -1855,14 +1858,14 @@
 	u16 sfp_type = hw->phy.sfp_type;
 
 	if (hw->phy.sfp_type == ixgbe_sfp_type_unknown)
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 
 	if (hw->phy.sfp_type == ixgbe_sfp_type_not_present)
-		return IXGBE_ERR_SFP_NOT_PRESENT;
+		return -ENOENT;
 
 	if ((hw->device_id == IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM) &&
 	    (hw->phy.sfp_type == ixgbe_sfp_type_da_cu))
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 
 	/*
 	 * Limiting active cables and 1G Phys must be initialized as
@@ -1883,11 +1886,11 @@
 	if (hw->eeprom.ops.read(hw, IXGBE_PHY_INIT_OFFSET_NL, list_offset)) {
 		hw_err(hw, "eeprom read at %d failed\n",
 		       IXGBE_PHY_INIT_OFFSET_NL);
-		return IXGBE_ERR_SFP_NO_INIT_SEQ_PRESENT;
+		return -EIO;
 	}
 
 	if ((!*list_offset) || (*list_offset == 0xFFFF))
-		return IXGBE_ERR_SFP_NO_INIT_SEQ_PRESENT;
+		return -EIO;
 
 	/* Shift offset to first ID word */
 	(*list_offset)++;
@@ -1906,7 +1909,7 @@
 				goto err_phy;
 			if ((!*data_offset) || (*data_offset == 0xFFFF)) {
 				hw_dbg(hw, "SFP+ module not supported\n");
-				return IXGBE_ERR_SFP_NOT_SUPPORTED;
+				return -EOPNOTSUPP;
 			} else {
 				break;
 			}
@@ -1919,14 +1922,14 @@
 
 	if (sfp_id == IXGBE_PHY_INIT_END_NL) {
 		hw_dbg(hw, "No matching SFP+ module found\n");
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 
 	return 0;
 
 err_phy:
 	hw_err(hw, "eeprom read at offset %d failed\n", *list_offset);
-	return IXGBE_ERR_PHY;
+	return -EIO;
 }
 
 /**
@@ -2021,7 +2024,7 @@
 
 	do {
 		if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask))
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 
 		ixgbe_i2c_start(hw);
 
@@ -2137,7 +2140,7 @@
 	u32 swfw_mask = hw->phy.phy_semaphore_mask;
 
 	if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	do {
 		ixgbe_i2c_start(hw);
@@ -2379,7 +2382,7 @@
 
 	if (ack == 1) {
 		hw_dbg(hw, "I2C ack was not received.\n");
-		status = IXGBE_ERR_I2C;
+		status = -EIO;
 	}
 
 	ixgbe_lower_i2c_clk(hw, &i2cctl);
@@ -2451,7 +2454,7 @@
 		udelay(IXGBE_I2C_T_LOW);
 	} else {
 		hw_dbg(hw, "I2C data was not set to %X\n", data);
-		return IXGBE_ERR_I2C;
+		return -EIO;
 	}
 
 	return 0;
@@ -2547,7 +2550,7 @@
 	*i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw));
 	if (data != ixgbe_get_i2c_data(hw, i2cctl)) {
 		hw_dbg(hw, "Error - I2C data was not set to %X.\n", data);
-		return IXGBE_ERR_I2C;
+		return -EIO;
 	}
 
 	return 0;
@@ -2617,22 +2620,24 @@
  *  @hw: pointer to hardware structure
  *
  *  Checks if the LASI temp alarm status was triggered due to overtemp
+ *
+ *  Return true when an overtemp event detected, otherwise false.
  **/
-s32 ixgbe_tn_check_overtemp(struct ixgbe_hw *hw)
+bool ixgbe_tn_check_overtemp(struct ixgbe_hw *hw)
 {
 	u16 phy_data = 0;
+	u32 status;
 
 	if (hw->device_id != IXGBE_DEV_ID_82599_T3_LOM)
-		return 0;
+		return false;
 
 	/* Check that the LASI temp alarm status was triggered */
-	hw->phy.ops.read_reg(hw, IXGBE_TN_LASI_STATUS_REG,
-			     MDIO_MMD_PMAPMD, &phy_data);
-
-	if (!(phy_data & IXGBE_TN_LASI_STATUS_TEMP_ALARM))
-		return 0;
+	status = hw->phy.ops.read_reg(hw, IXGBE_TN_LASI_STATUS_REG,
+				      MDIO_MMD_PMAPMD, &phy_data);
+	if (status)
+		return false;
 
-	return IXGBE_ERR_OVERTEMP;
+	return !!(phy_data & IXGBE_TN_LASI_STATUS_TEMP_ALARM);
 }
 
 /** ixgbe_set_copper_phy_power - Control power for copper phy
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
@@ -155,7 +155,7 @@
 s32 ixgbe_get_sfp_init_sequence_offsets(struct ixgbe_hw *hw,
 					u16 *list_offset,
 					u16 *data_offset);
-s32 ixgbe_tn_check_overtemp(struct ixgbe_hw *hw);
+bool ixgbe_tn_check_overtemp(struct ixgbe_hw *hw);
 s32 ixgbe_read_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset,
 				u8 dev_addr, u8 *data);
 s32 ixgbe_read_i2c_byte_generic_unlocked(struct ixgbe_hw *hw, u8 byte_offset,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
@@ -989,6 +989,7 @@
 	u32 tsync_tx_ctl = IXGBE_TSYNCTXCTL_ENABLED;
 	u32 tsync_rx_ctl = IXGBE_TSYNCRXCTL_ENABLED;
 	u32 tsync_rx_mtrl = PTP_EV_PORT << 16;
+	u32 aflags = adapter->flags;
 	bool is_l2 = false;
 	u32 regval;
 
@@ -1010,20 +1011,20 @@
 	case HWTSTAMP_FILTER_NONE:
 		tsync_rx_ctl = 0;
 		tsync_rx_mtrl = 0;
-		adapter->flags &= ~(IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				    IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		aflags &= ~(IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+			    IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_L4_V1;
 		tsync_rx_mtrl |= IXGBE_RXMTRL_V1_SYNC_MSG;
-		adapter->flags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		aflags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+			   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_L4_V1;
 		tsync_rx_mtrl |= IXGBE_RXMTRL_V1_DELAY_REQ_MSG;
-		adapter->flags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		aflags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+			   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V2_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
@@ -1037,8 +1038,8 @@
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_EVENT_V2;
 		is_l2 = true;
 		config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
-		adapter->flags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
+		aflags |= (IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
+			   IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		break;
 	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
 	case HWTSTAMP_FILTER_NTP_ALL:
@@ -1049,7 +1050,7 @@
 		if (hw->mac.type >= ixgbe_mac_X550) {
 			tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_ALL;
 			config->rx_filter = HWTSTAMP_FILTER_ALL;
-			adapter->flags |= IXGBE_FLAG_RX_HWTSTAMP_ENABLED;
+			aflags |= IXGBE_FLAG_RX_HWTSTAMP_ENABLED;
 			break;
 		}
 		fallthrough;
@@ -1060,8 +1061,6 @@
 		 * Delay_Req messages and hardware does not support
 		 * timestamping all packets => return error
 		 */
-		adapter->flags &= ~(IXGBE_FLAG_RX_HWTSTAMP_ENABLED |
-				    IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER);
 		config->rx_filter = HWTSTAMP_FILTER_NONE;
 		return -ERANGE;
 	}
@@ -1093,8 +1092,8 @@
 			       IXGBE_TSYNCRXCTL_TYPE_ALL |
 			       IXGBE_TSYNCRXCTL_TSIP_UT_EN;
 		config->rx_filter = HWTSTAMP_FILTER_ALL;
-		adapter->flags |= IXGBE_FLAG_RX_HWTSTAMP_ENABLED;
-		adapter->flags &= ~IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER;
+		aflags |= IXGBE_FLAG_RX_HWTSTAMP_ENABLED;
+		aflags &= ~IXGBE_FLAG_RX_HWTSTAMP_IN_REGISTER;
 		is_l2 = true;
 		break;
 	default:
@@ -1127,6 +1126,9 @@
 
 	IXGBE_WRITE_FLUSH(hw);
 
+	/* configure adapter flags only when HW is actually configured */
+	adapter->flags = aflags;
+
 	/* clear TX/RX time stamp registers, just to be sure */
 	ixgbe_ptp_clear_tx_timestamp(adapter);
 	IXGBE_READ_REG(hw, IXGBE_RXSTMPH);
@@ -1212,7 +1214,6 @@
 	struct cyclecounter cc;
 	unsigned long flags;
 	u32 incval = 0;
-	u32 tsauxc = 0;
 	u32 fuse0 = 0;
 
 	/* For some of the boards below this mask is technically incorrect.
@@ -1247,18 +1248,6 @@
 	case ixgbe_mac_x550em_a:
 	case ixgbe_mac_X550:
 		cc.read = ixgbe_ptp_read_X550;
-
-		/* enable SYSTIME counter */
-		IXGBE_WRITE_REG(hw, IXGBE_SYSTIMR, 0);
-		IXGBE_WRITE_REG(hw, IXGBE_SYSTIML, 0);
-		IXGBE_WRITE_REG(hw, IXGBE_SYSTIMH, 0);
-		tsauxc = IXGBE_READ_REG(hw, IXGBE_TSAUXC);
-		IXGBE_WRITE_REG(hw, IXGBE_TSAUXC,
-				tsauxc & ~IXGBE_TSAUXC_DISABLE_SYSTIME);
-		IXGBE_WRITE_REG(hw, IXGBE_TSIM, IXGBE_TSIM_TXTS);
-		IXGBE_WRITE_REG(hw, IXGBE_EIMS, IXGBE_EIMS_TIMESYNC);
-
-		IXGBE_WRITE_FLUSH(hw);
 		break;
 	case ixgbe_mac_X540:
 		cc.read = ixgbe_ptp_read_82599;
@@ -1291,6 +1280,50 @@
 }
 
 /**
+ * ixgbe_ptp_init_systime - Initialize SYSTIME registers
+ * @adapter: the ixgbe private board structure
+ *
+ * Initialize and start the SYSTIME registers.
+ */
+static void ixgbe_ptp_init_systime(struct ixgbe_adapter *adapter)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+	u32 tsauxc;
+
+	switch (hw->mac.type) {
+	case ixgbe_mac_X550EM_x:
+	case ixgbe_mac_x550em_a:
+	case ixgbe_mac_X550:
+		tsauxc = IXGBE_READ_REG(hw, IXGBE_TSAUXC);
+
+		/* Reset SYSTIME registers to 0 */
+		IXGBE_WRITE_REG(hw, IXGBE_SYSTIMR, 0);
+		IXGBE_WRITE_REG(hw, IXGBE_SYSTIML, 0);
+		IXGBE_WRITE_REG(hw, IXGBE_SYSTIMH, 0);
+
+		/* Reset interrupt settings */
+		IXGBE_WRITE_REG(hw, IXGBE_TSIM, IXGBE_TSIM_TXTS);
+		IXGBE_WRITE_REG(hw, IXGBE_EIMS, IXGBE_EIMS_TIMESYNC);
+
+		/* Activate the SYSTIME counter */
+		IXGBE_WRITE_REG(hw, IXGBE_TSAUXC,
+				tsauxc & ~IXGBE_TSAUXC_DISABLE_SYSTIME);
+		break;
+	case ixgbe_mac_X540:
+	case ixgbe_mac_82599EB:
+		/* Reset SYSTIME registers to 0 */
+		IXGBE_WRITE_REG(hw, IXGBE_SYSTIML, 0);
+		IXGBE_WRITE_REG(hw, IXGBE_SYSTIMH, 0);
+		break;
+	default:
+		/* Other devices aren't supported */
+		return;
+	};
+
+	IXGBE_WRITE_FLUSH(hw);
+}
+
+/**
  * ixgbe_ptp_reset
  * @adapter: the ixgbe private board structure
  *
@@ -1316,6 +1349,8 @@
 
 	ixgbe_ptp_start_cyclecounter(adapter);
 
+	ixgbe_ptp_init_systime(adapter);
+
 	spin_lock_irqsave(&adapter->tmreg_lock, flags);
 	timecounter_init(&adapter->hw_tc, &adapter->hw_cc,
 			 ktime_to_ns(ktime_get_real()));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
@@ -28,6 +28,9 @@
 	struct vf_macvlans *mv_list;
 	int num_vf_macvlans, i;
 
+	/* Initialize list of VF macvlans */
+	INIT_LIST_HEAD(&adapter->vf_mvs.l);
+
 	num_vf_macvlans = hw->mac.num_rar_entries -
 			  (IXGBE_MAX_PF_MACVLANS + 1 + num_vfs);
 	if (!num_vf_macvlans)
@@ -36,8 +39,6 @@
 	mv_list = kcalloc(num_vf_macvlans, sizeof(struct vf_macvlans),
 			  GFP_KERNEL);
 	if (mv_list) {
-		/* Initialize list of VF macvlans */
-		INIT_LIST_HEAD(&adapter->vf_mvs.l);
 		for (i = 0; i < num_vf_macvlans; i++) {
 			mv_list[i].vf = -1;
 			mv_list[i].free = true;
@@ -96,6 +97,7 @@
 	for (i = 0; i < num_vfs; i++) {
 		/* enable spoof checking for all VFs */
 		adapter->vfinfo[i].spoofchk_enabled = true;
+		adapter->vfinfo[i].link_enable = true;
 
 		/* We support VF RSS querying only for 82599 and x540
 		 * devices at the moment. These devices share RSS
@@ -204,10 +206,13 @@
 int ixgbe_disable_sriov(struct ixgbe_adapter *adapter)
 {
 	unsigned int num_vfs = adapter->num_vfs, vf;
+	unsigned long flags;
 	int rss;
 
+	spin_lock_irqsave(&adapter->vfs_lock, flags);
 	/* set num VFs to 0 to prevent access to vfinfo */
 	adapter->num_vfs = 0;
+	spin_unlock_irqrestore(&adapter->vfs_lock, flags);
 
 	/* put the reference to all of the vf devices */
 	for (vf = 0; vf < num_vfs; ++vf) {
@@ -820,6 +825,57 @@
 	}
 }
 
+/**
+ * ixgbe_set_vf_rx_tx - Set VF rx tx
+ * @adapter: Pointer to adapter struct
+ * @vf: VF identifier
+ *
+ * Set or reset correct transmit and receive for vf
+ **/
+static void ixgbe_set_vf_rx_tx(struct ixgbe_adapter *adapter, int vf)
+{
+	u32 reg_cur_tx, reg_cur_rx, reg_req_tx, reg_req_rx;
+	struct ixgbe_hw *hw = &adapter->hw;
+	u32 reg_offset, vf_shift;
+
+	vf_shift = vf % 32;
+	reg_offset = vf / 32;
+
+	reg_cur_tx = IXGBE_READ_REG(hw, IXGBE_VFTE(reg_offset));
+	reg_cur_rx = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset));
+
+	if (adapter->vfinfo[vf].link_enable) {
+		reg_req_tx = reg_cur_tx | 1 << vf_shift;
+		reg_req_rx = reg_cur_rx | 1 << vf_shift;
+	} else {
+		reg_req_tx = reg_cur_tx & ~(1 << vf_shift);
+		reg_req_rx = reg_cur_rx & ~(1 << vf_shift);
+	}
+
+	/* The 82599 cannot support a mix of jumbo and non-jumbo PF/VFs.
+	 * For more info take a look at ixgbe_set_vf_lpe
+	 */
+	if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
+		struct net_device *dev = adapter->netdev;
+		int pf_max_frame = dev->mtu + ETH_HLEN;
+
+#if IS_ENABLED(CONFIG_FCOE)
+		if (dev->features & NETIF_F_FCOE_MTU)
+			pf_max_frame = max_t(int, pf_max_frame,
+					     IXGBE_FCOE_JUMBO_FRAME_SIZE);
+#endif /* CONFIG_FCOE */
+
+		if (pf_max_frame > ETH_FRAME_LEN)
+			reg_req_rx = reg_cur_rx & ~(1 << vf_shift);
+	}
+
+	/* Enable/Disable particular VF */
+	if (reg_cur_tx != reg_req_tx)
+		IXGBE_WRITE_REG(hw, IXGBE_VFTE(reg_offset), reg_req_tx);
+	if (reg_cur_rx != reg_req_rx)
+		IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), reg_req_rx);
+}
+
 static int ixgbe_vf_reset_msg(struct ixgbe_adapter *adapter, u32 vf)
 {
 	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
@@ -845,11 +901,6 @@
 	vf_shift = vf % 32;
 	reg_offset = vf / 32;
 
-	/* enable transmit for vf */
-	reg = IXGBE_READ_REG(hw, IXGBE_VFTE(reg_offset));
-	reg |= BIT(vf_shift);
-	IXGBE_WRITE_REG(hw, IXGBE_VFTE(reg_offset), reg);
-
 	/* force drop enable for all VF Rx queues */
 	reg = IXGBE_QDE_ENABLE;
 	if (adapter->vfinfo[vf].pf_vlan)
@@ -857,27 +908,7 @@
 
 	ixgbe_write_qde(adapter, vf, reg);
 
-	/* enable receive for vf */
-	reg = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset));
-	reg |= BIT(vf_shift);
-	/*
-	 * The 82599 cannot support a mix of jumbo and non-jumbo PF/VFs.
-	 * For more info take a look at ixgbe_set_vf_lpe
-	 */
-	if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
-		struct net_device *dev = adapter->netdev;
-		int pf_max_frame = dev->mtu + ETH_HLEN;
-
-#ifdef CONFIG_FCOE
-		if (dev->features & NETIF_F_FCOE_MTU)
-			pf_max_frame = max_t(int, pf_max_frame,
-					     IXGBE_FCOE_JUMBO_FRAME_SIZE);
-
-#endif /* CONFIG_FCOE */
-		if (pf_max_frame > ETH_FRAME_LEN)
-			reg &= ~BIT(vf_shift);
-	}
-	IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), reg);
+	ixgbe_set_vf_rx_tx(adapter, vf);
 
 	/* enable VF mailbox for further messages */
 	adapter->vfinfo[vf].clear_to_send = true;
@@ -1157,9 +1188,9 @@
 
 	switch (xcast_mode) {
 	case IXGBEVF_XCAST_MODE_NONE:
-		disable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE |
+		disable = IXGBE_VMOLR_ROMPE |
 			  IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
-		enable = 0;
+		enable = IXGBE_VMOLR_BAM;
 		break;
 	case IXGBEVF_XCAST_MODE_MULTI:
 		disable = IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
@@ -1181,9 +1212,9 @@
 			return -EPERM;
 		}
 
-		disable = 0;
+		disable = IXGBE_VMOLR_VPE;
 		enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE |
-			 IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE | IXGBE_VMOLR_VPE;
+			 IXGBE_VMOLR_MPE | IXGBE_VMOLR_UPE;
 		break;
 	default:
 		return -EOPNOTSUPP;
@@ -1202,6 +1233,26 @@
 	return 0;
 }
 
+static int ixgbe_get_vf_link_state(struct ixgbe_adapter *adapter,
+				   u32 *msgbuf, u32 vf)
+{
+	u32 *link_state = &msgbuf[1];
+
+	/* verify the PF is supporting the correct API */
+	switch (adapter->vfinfo[vf].vf_api) {
+	case ixgbe_mbox_api_12:
+	case ixgbe_mbox_api_13:
+	case ixgbe_mbox_api_14:
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	*link_state = adapter->vfinfo[vf].link_enable;
+
+	return 0;
+}
+
 static int ixgbe_rcv_msg_from_vf(struct ixgbe_adapter *adapter, u32 vf)
 {
 	u32 mbx_size = IXGBE_VFMAILBOX_SIZE;
@@ -1267,6 +1318,9 @@
 	case IXGBE_VF_UPDATE_XCAST_MODE:
 		retval = ixgbe_update_vf_xcast_mode(adapter, msgbuf, vf);
 		break;
+	case IXGBE_VF_GET_LINK_STATE:
+		retval = ixgbe_get_vf_link_state(adapter, msgbuf, vf);
+		break;
 	case IXGBE_VF_IPSEC_ADD:
 		retval = ixgbe_ipsec_vf_add_sa(adapter, msgbuf, vf);
 		break;
@@ -1275,7 +1329,7 @@
 		break;
 	default:
 		e_err(drv, "Unhandled Msg %8.8x\n", msgbuf[0]);
-		retval = IXGBE_ERR_MBX;
+		retval = -EIO;
 		break;
 	}
 
@@ -1305,8 +1359,10 @@
 void ixgbe_msg_task(struct ixgbe_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
+	unsigned long flags;
 	u32 vf;
 
+	spin_lock_irqsave(&adapter->vfs_lock, flags);
 	for (vf = 0; vf < adapter->num_vfs; vf++) {
 		/* process any reset requests */
 		if (!ixgbe_check_for_rst(hw, vf))
@@ -1320,18 +1376,7 @@
 		if (!ixgbe_check_for_ack(hw, vf))
 			ixgbe_rcv_ack_from_vf(adapter, vf);
 	}
-}
-
-void ixgbe_disable_tx_rx(struct ixgbe_adapter *adapter)
-{
-	struct ixgbe_hw *hw = &adapter->hw;
-
-	/* disable transmit and receive for all vfs */
-	IXGBE_WRITE_REG(hw, IXGBE_VFTE(0), 0);
-	IXGBE_WRITE_REG(hw, IXGBE_VFTE(1), 0);
-
-	IXGBE_WRITE_REG(hw, IXGBE_VFRE(0), 0);
-	IXGBE_WRITE_REG(hw, IXGBE_VFRE(1), 0);
+	spin_unlock_irqrestore(&adapter->vfs_lock, flags);
 }
 
 static inline void ixgbe_ping_vf(struct ixgbe_adapter *adapter, int vf)
@@ -1359,6 +1404,21 @@
 	}
 }
 
+/**
+ * ixgbe_set_all_vfs - update vfs queues
+ * @adapter: Pointer to adapter struct
+ *
+ * Update setting transmit and receive queues for all vfs
+ **/
+void ixgbe_set_all_vfs(struct ixgbe_adapter *adapter)
+{
+	int i;
+
+	for (i = 0 ; i < adapter->num_vfs; i++)
+		ixgbe_set_vf_link_state(adapter, i,
+					adapter->vfinfo[i].link_state);
+}
+
 int ixgbe_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
@@ -1656,6 +1716,84 @@
 	return 0;
 }
 
+/**
+ * ixgbe_set_vf_link_state - Set link state
+ * @adapter: Pointer to adapter struct
+ * @vf: VF identifier
+ * @state: required link state
+ *
+ * Set a link force state on/off a single vf
+ **/
+void ixgbe_set_vf_link_state(struct ixgbe_adapter *adapter, int vf, int state)
+{
+	adapter->vfinfo[vf].link_state = state;
+
+	switch (state) {
+	case IFLA_VF_LINK_STATE_AUTO:
+		if (test_bit(__IXGBE_DOWN, &adapter->state))
+			adapter->vfinfo[vf].link_enable = false;
+		else
+			adapter->vfinfo[vf].link_enable = true;
+		break;
+	case IFLA_VF_LINK_STATE_ENABLE:
+		adapter->vfinfo[vf].link_enable = true;
+		break;
+	case IFLA_VF_LINK_STATE_DISABLE:
+		adapter->vfinfo[vf].link_enable = false;
+		break;
+	}
+
+	ixgbe_set_vf_rx_tx(adapter, vf);
+
+	/* restart the VF */
+	adapter->vfinfo[vf].clear_to_send = false;
+	ixgbe_ping_vf(adapter, vf);
+}
+
+/**
+ * ixgbe_ndo_set_vf_link_state - Set link state
+ * @netdev: network interface device structure
+ * @vf: VF identifier
+ * @state: required link state
+ *
+ * Set the link state of a specified VF, regardless of physical link state
+ **/
+int ixgbe_ndo_set_vf_link_state(struct net_device *netdev, int vf, int state)
+{
+	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	int ret = 0;
+
+	if (vf < 0 || vf >= adapter->num_vfs) {
+		dev_err(&adapter->pdev->dev,
+			"NDO set VF link - invalid VF identifier %d\n", vf);
+		return -EINVAL;
+	}
+
+	switch (state) {
+	case IFLA_VF_LINK_STATE_ENABLE:
+		dev_info(&adapter->pdev->dev,
+			 "NDO set VF %d link state %d - not supported\n",
+			vf, state);
+		break;
+	case IFLA_VF_LINK_STATE_DISABLE:
+		dev_info(&adapter->pdev->dev,
+			 "NDO set VF %d link state disable\n", vf);
+		ixgbe_set_vf_link_state(adapter, vf, state);
+		break;
+	case IFLA_VF_LINK_STATE_AUTO:
+		dev_info(&adapter->pdev->dev,
+			 "NDO set VF %d link state auto\n", vf);
+		ixgbe_set_vf_link_state(adapter, vf, state);
+		break;
+	default:
+		dev_err(&adapter->pdev->dev,
+			"NDO set VF %d - invalid link state %d\n", vf, state);
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
 int ixgbe_ndo_set_vf_rss_query_en(struct net_device *netdev, int vf,
 				  bool setting)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.h
@@ -17,8 +17,8 @@
 #endif
 void ixgbe_msg_task(struct ixgbe_adapter *adapter);
 int ixgbe_vf_configuration(struct pci_dev *pdev, unsigned int event_mask);
-void ixgbe_disable_tx_rx(struct ixgbe_adapter *adapter);
 void ixgbe_ping_all_vfs(struct ixgbe_adapter *adapter);
+void ixgbe_set_all_vfs(struct ixgbe_adapter *adapter);
 int ixgbe_ndo_set_vf_mac(struct net_device *netdev, int queue, u8 *mac);
 int ixgbe_ndo_set_vf_vlan(struct net_device *netdev, int queue, u16 vlan,
 			   u8 qos, __be16 vlan_proto);
@@ -31,7 +31,9 @@
 int ixgbe_ndo_set_vf_trust(struct net_device *netdev, int vf, bool setting);
 int ixgbe_ndo_get_vf_config(struct net_device *netdev,
 			    int vf, struct ifla_vf_info *ivi);
+int ixgbe_ndo_set_vf_link_state(struct net_device *netdev, int vf, int state);
 void ixgbe_check_vf_rate_limit(struct ixgbe_adapter *adapter);
+void ixgbe_set_vf_link_state(struct ixgbe_adapter *adapter, int vf, int state);
 int ixgbe_disable_sriov(struct ixgbe_adapter *adapter);
 #ifdef CONFIG_PCI_IOV
 void ixgbe_enable_sriov(struct ixgbe_adapter *adapter, unsigned int max_vfs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -1247,7 +1247,7 @@
 #define IXGBE_PSRTYPE_RQPL_SHIFT    29
 
 /* CTRL Bit Masks */
-#define IXGBE_CTRL_GIO_DIS      0x00000004 /* Global IO Master Disable bit */
+#define IXGBE_CTRL_GIO_DIS      0x00000004 /* Global IO Primary Disable bit */
 #define IXGBE_CTRL_LNK_RST      0x00000008 /* Link Reset. Resets everything. */
 #define IXGBE_CTRL_RST          0x04000000 /* Reset (SW) */
 #define IXGBE_CTRL_RST_MASK     (IXGBE_CTRL_LNK_RST | IXGBE_CTRL_RST)
@@ -1811,7 +1811,7 @@
 /* STATUS Bit Masks */
 #define IXGBE_STATUS_LAN_ID         0x0000000C /* LAN ID */
 #define IXGBE_STATUS_LAN_ID_SHIFT   2          /* LAN ID Shift*/
-#define IXGBE_STATUS_GIO            0x00080000 /* GIO Master Enable Status */
+#define IXGBE_STATUS_GIO            0x00080000 /* GIO Primary Enable Status */
 
 #define IXGBE_STATUS_LAN_ID_0   0x00000000 /* LAN ID 0 */
 #define IXGBE_STATUS_LAN_ID_1   0x00000004 /* LAN ID 1 */
@@ -2193,8 +2193,8 @@
 #define IXGBE_PCIDEVCTRL2_4_8s		0xd
 #define IXGBE_PCIDEVCTRL2_17_34s	0xe
 
-/* Number of 100 microseconds we wait for PCI Express master disable */
-#define IXGBE_PCI_MASTER_DISABLE_TIMEOUT	800
+/* Number of 100 microseconds we wait for PCI Express primary disable */
+#define IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT	800
 
 /* RAH */
 #define IXGBE_RAH_VIND_MASK     0x003C0000
@@ -3502,10 +3502,10 @@
 	s32 (*read_i2c_sff8472)(struct ixgbe_hw *, u8 , u8 *);
 	s32 (*read_i2c_eeprom)(struct ixgbe_hw *, u8 , u8 *);
 	s32 (*write_i2c_eeprom)(struct ixgbe_hw *, u8, u8);
-	s32 (*check_overtemp)(struct ixgbe_hw *);
+	bool (*check_overtemp)(struct ixgbe_hw *);
 	s32 (*set_phy_power)(struct ixgbe_hw *, bool on);
 	s32 (*enter_lplu)(struct ixgbe_hw *);
-	s32 (*handle_lasi)(struct ixgbe_hw *hw);
+	s32 (*handle_lasi)(struct ixgbe_hw *hw, bool *);
 	s32 (*read_i2c_byte_unlocked)(struct ixgbe_hw *, u8 offset, u8 addr,
 				      u8 *value);
 	s32 (*write_i2c_byte_unlocked)(struct ixgbe_hw *, u8 offset, u8 addr,
@@ -3658,45 +3658,6 @@
 	const u32			*mvals;
 };
 
-
-/* Error Codes */
-#define IXGBE_ERR_EEPROM                        -1
-#define IXGBE_ERR_EEPROM_CHECKSUM               -2
-#define IXGBE_ERR_PHY                           -3
-#define IXGBE_ERR_CONFIG                        -4
-#define IXGBE_ERR_PARAM                         -5
-#define IXGBE_ERR_MAC_TYPE                      -6
-#define IXGBE_ERR_UNKNOWN_PHY                   -7
-#define IXGBE_ERR_LINK_SETUP                    -8
-#define IXGBE_ERR_ADAPTER_STOPPED               -9
-#define IXGBE_ERR_INVALID_MAC_ADDR              -10
-#define IXGBE_ERR_DEVICE_NOT_SUPPORTED          -11
-#define IXGBE_ERR_MASTER_REQUESTS_PENDING       -12
-#define IXGBE_ERR_INVALID_LINK_SETTINGS         -13
-#define IXGBE_ERR_AUTONEG_NOT_COMPLETE          -14
-#define IXGBE_ERR_RESET_FAILED                  -15
-#define IXGBE_ERR_SWFW_SYNC                     -16
-#define IXGBE_ERR_PHY_ADDR_INVALID              -17
-#define IXGBE_ERR_I2C                           -18
-#define IXGBE_ERR_SFP_NOT_SUPPORTED             -19
-#define IXGBE_ERR_SFP_NOT_PRESENT               -20
-#define IXGBE_ERR_SFP_NO_INIT_SEQ_PRESENT       -21
-#define IXGBE_ERR_NO_SAN_ADDR_PTR               -22
-#define IXGBE_ERR_FDIR_REINIT_FAILED            -23
-#define IXGBE_ERR_EEPROM_VERSION                -24
-#define IXGBE_ERR_NO_SPACE                      -25
-#define IXGBE_ERR_OVERTEMP                      -26
-#define IXGBE_ERR_FC_NOT_NEGOTIATED             -27
-#define IXGBE_ERR_FC_NOT_SUPPORTED              -28
-#define IXGBE_ERR_SFP_SETUP_NOT_COMPLETE        -30
-#define IXGBE_ERR_PBA_SECTION                   -31
-#define IXGBE_ERR_INVALID_ARGUMENT              -32
-#define IXGBE_ERR_HOST_INTERFACE_COMMAND        -33
-#define IXGBE_ERR_FDIR_CMD_INCOMPLETE		-38
-#define IXGBE_ERR_FW_RESP_INVALID		-39
-#define IXGBE_ERR_TOKEN_RETRY			-40
-#define IXGBE_NOT_IMPLEMENTED                   0x7FFFFFFF
-
 #define IXGBE_FUSES0_GROUP(_i)		(0x11158 + ((_i) * 4))
 #define IXGBE_FUSES0_300MHZ		BIT(5)
 #define IXGBE_FUSES0_REV_MASK		(3u << 6)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
@@ -84,7 +84,7 @@
 	status = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask);
 	if (status) {
 		hw_dbg(hw, "semaphore failed with %d", status);
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 	}
 
 	ctrl = IXGBE_CTRL_RST;
@@ -103,7 +103,7 @@
 	}
 
 	if (ctrl & IXGBE_CTRL_RST_MASK) {
-		status = IXGBE_ERR_RESET_FAILED;
+		status = -EIO;
 		hw_dbg(hw, "Reset polling failed to complete.\n");
 	}
 	msleep(100);
@@ -220,7 +220,7 @@
 	s32 status;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = ixgbe_read_eerd_generic(hw, offset, data);
 
@@ -243,7 +243,7 @@
 	s32 status;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = ixgbe_read_eerd_buffer_generic(hw, offset, words, data);
 
@@ -264,7 +264,7 @@
 	s32 status;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = ixgbe_write_eewr_generic(hw, offset, data);
 
@@ -287,7 +287,7 @@
 	s32 status;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = ixgbe_write_eewr_buffer_generic(hw, offset, words, data);
 
@@ -324,7 +324,7 @@
 	for (i = 0; i < checksum_last_word; i++) {
 		if (ixgbe_read_eerd_generic(hw, i, &word)) {
 			hw_dbg(hw, "EEPROM read failed\n");
-			return IXGBE_ERR_EEPROM;
+			return -EIO;
 		}
 		checksum += word;
 	}
@@ -349,7 +349,7 @@
 
 		if (ixgbe_read_eerd_generic(hw, pointer, &length)) {
 			hw_dbg(hw, "EEPROM read failed\n");
-			return IXGBE_ERR_EEPROM;
+			return -EIO;
 		}
 
 		/* Skip pointer section if length is invalid. */
@@ -360,7 +360,7 @@
 		for (j = pointer + 1; j <= pointer + length; j++) {
 			if (ixgbe_read_eerd_generic(hw, j, &word)) {
 				hw_dbg(hw, "EEPROM read failed\n");
-				return IXGBE_ERR_EEPROM;
+				return -EIO;
 			}
 			checksum += word;
 		}
@@ -397,7 +397,7 @@
 	}
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = hw->eeprom.ops.calc_checksum(hw);
 	if (status < 0)
@@ -418,7 +418,7 @@
 	 */
 	if (read_checksum != checksum) {
 		hw_dbg(hw, "Invalid EEPROM checksum");
-		status = IXGBE_ERR_EEPROM_CHECKSUM;
+		status = -EIO;
 	}
 
 	/* If the user cares, return the calculated checksum */
@@ -455,7 +455,7 @@
 	}
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM))
-		return  IXGBE_ERR_SWFW_SYNC;
+		return  -EBUSY;
 
 	status = hw->eeprom.ops.calc_checksum(hw);
 	if (status < 0)
@@ -490,7 +490,7 @@
 	s32 status;
 
 	status = ixgbe_poll_flash_update_done_X540(hw);
-	if (status == IXGBE_ERR_EEPROM) {
+	if (status == -EIO) {
 		hw_dbg(hw, "Flash update time out\n");
 		return status;
 	}
@@ -540,7 +540,7 @@
 			return 0;
 		udelay(5);
 	}
-	return IXGBE_ERR_EEPROM;
+	return -EIO;
 }
 
 /**
@@ -575,7 +575,7 @@
 		 * SW_FW_SYNC bits (not just NVM)
 		 */
 		if (ixgbe_get_swfw_sync_semaphore(hw))
-			return IXGBE_ERR_SWFW_SYNC;
+			return -EBUSY;
 
 		swfw_sync = IXGBE_READ_REG(hw, IXGBE_SWFW_SYNC(hw));
 		if (!(swfw_sync & (fwmask | swmask | hwmask))) {
@@ -599,7 +599,7 @@
 	 * bits in the SW_FW_SYNC register.
 	 */
 	if (ixgbe_get_swfw_sync_semaphore(hw))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 	swfw_sync = IXGBE_READ_REG(hw, IXGBE_SWFW_SYNC(hw));
 	if (swfw_sync & (fwmask | hwmask)) {
 		swfw_sync |= swmask;
@@ -622,11 +622,11 @@
 			rmask |= IXGBE_GSSR_I2C_MASK;
 		ixgbe_release_swfw_sync_X540(hw, rmask);
 		ixgbe_release_swfw_sync_semaphore(hw);
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 	}
 	ixgbe_release_swfw_sync_semaphore(hw);
 
-	return IXGBE_ERR_SWFW_SYNC;
+	return -EBUSY;
 }
 
 /**
@@ -680,7 +680,7 @@
 	if (i == timeout) {
 		hw_dbg(hw,
 		       "Software semaphore SMBI between device drivers not granted.\n");
-		return IXGBE_ERR_EEPROM;
+		return -EIO;
 	}
 
 	/* Now get the semaphore between SW/FW through the REGSMP bit */
@@ -697,7 +697,7 @@
 	 */
 	hw_dbg(hw, "REGSMP Software NVM semaphore not granted\n");
 	ixgbe_release_swfw_sync_semaphore(hw);
-	return IXGBE_ERR_EEPROM;
+	return -EIO;
 }
 
 /**
@@ -768,7 +768,7 @@
 	bool link_up;
 
 	if (index > 3)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* Link should be up in order for the blink bit in the LED control
 	 * register to work. Force link and speed in the MAC if link is down.
@@ -804,7 +804,7 @@
 	u32 ledctl_reg;
 
 	if (index > 3)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* Restore the LED to its default value. */
 	ledctl_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -206,13 +206,13 @@
 	}
 	if (retry == IXGBE_CS4227_RETRIES) {
 		hw_err(hw, "CS4227 reset did not complete\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	status = ixgbe_read_cs4227(hw, IXGBE_CS4227_EEPROM_STATUS, &value);
 	if (status || !(value & IXGBE_CS4227_EEPROM_LOAD_OK)) {
 		hw_err(hw, "CS4227 EEPROM did not load successfully\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	return 0;
@@ -350,13 +350,13 @@
 static s32 ixgbe_read_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr,
 				     u32 device_type, u16 *phy_data)
 {
-	return IXGBE_NOT_IMPLEMENTED;
+	return -EOPNOTSUPP;
 }
 
 static s32 ixgbe_write_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr,
 				      u32 device_type, u16 phy_data)
 {
-	return IXGBE_NOT_IMPLEMENTED;
+	return -EOPNOTSUPP;
 }
 
 /**
@@ -463,7 +463,7 @@
 		--retries;
 	} while (retries > 0);
 
-	return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+	return -EIO;
 }
 
 static const struct {
@@ -511,7 +511,7 @@
 	hw->phy.id |= phy_id_lo & IXGBE_PHY_REVISION_MASK;
 	hw->phy.revision = phy_id_lo & ~IXGBE_PHY_REVISION_MASK;
 	if (!hw->phy.id || hw->phy.id == IXGBE_PHY_REVISION_MASK)
-		return IXGBE_ERR_PHY_ADDR_INVALID;
+		return -EFAULT;
 
 	hw->phy.autoneg_advertised = hw->phy.speeds_supported;
 	hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_100_FULL |
@@ -568,7 +568,7 @@
 
 	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
 		hw_err(hw, "rx_pause not valid in strict IEEE mode\n");
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 	}
 
 	switch (hw->fc.requested_mode) {
@@ -600,8 +600,10 @@
 	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_SETUP_LINK, &setup);
 	if (rc)
 		return rc;
+
 	if (setup[0] == FW_PHY_ACT_SETUP_LINK_RSP_DOWN)
-		return IXGBE_ERR_OVERTEMP;
+		return -EIO;
+
 	return 0;
 }
 
@@ -675,7 +677,7 @@
 		*ctrl = command;
 	if (i == IXGBE_MDIO_COMMAND_TIMEOUT) {
 		hw_dbg(hw, "IOSF wait timed out\n");
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 	return 0;
@@ -715,7 +717,8 @@
 		error = (command & IXGBE_SB_IOSF_CTRL_CMPL_ERR_MASK) >>
 			 IXGBE_SB_IOSF_CTRL_CMPL_ERR_SHIFT;
 		hw_dbg(hw, "Failed to read, error %x\n", error);
-		return IXGBE_ERR_PHY;
+		ret = -EIO;
+		goto out;
 	}
 
 	if (!ret)
@@ -750,9 +753,9 @@
 	if (token_cmd.hdr.cmd_or_resp.ret_status == FW_PHY_TOKEN_OK)
 		return 0;
 	if (token_cmd.hdr.cmd_or_resp.ret_status != FW_PHY_TOKEN_RETRY)
-		return IXGBE_ERR_FW_RESP_INVALID;
+		return -EIO;
 
-	return IXGBE_ERR_TOKEN_RETRY;
+	return -EAGAIN;
 }
 
 /**
@@ -778,7 +781,7 @@
 		return status;
 	if (token_cmd.hdr.cmd_or_resp.ret_status == FW_PHY_TOKEN_OK)
 		return 0;
-	return IXGBE_ERR_FW_RESP_INVALID;
+	return -EIO;
 }
 
 /**
@@ -942,7 +945,7 @@
 		local_buffer = buf;
 	} else {
 		if (buffer_size < ptr)
-			return  IXGBE_ERR_PARAM;
+			return  -EINVAL;
 		local_buffer = &buffer[ptr];
 	}
 
@@ -960,7 +963,7 @@
 	}
 
 	if (buffer && ((u32)start + (u32)length > buffer_size))
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	for (i = start; length; i++, length--) {
 		if (i == bufsz && !buffer) {
@@ -1012,7 +1015,7 @@
 		local_buffer = eeprom_ptrs;
 	} else {
 		if (buffer_size < IXGBE_EEPROM_LAST_WORD)
-			return IXGBE_ERR_PARAM;
+			return -EINVAL;
 		local_buffer = buffer;
 	}
 
@@ -1148,7 +1151,7 @@
 	 * calculated checksum
 	 */
 	if (read_checksum != checksum) {
-		status = IXGBE_ERR_EEPROM_CHECKSUM;
+		status = -EIO;
 		hw_dbg(hw, "Invalid EEPROM checksum");
 	}
 
@@ -1203,7 +1206,7 @@
 		hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
 	} else {
 		hw_dbg(hw, "write ee hostif failed to get semaphore");
-		status = IXGBE_ERR_SWFW_SYNC;
+		status = -EBUSY;
 	}
 
 	return status;
@@ -1415,7 +1418,7 @@
 		error = (command & IXGBE_SB_IOSF_CTRL_CMPL_ERR_MASK) >>
 			 IXGBE_SB_IOSF_CTRL_CMPL_ERR_SHIFT;
 		hw_dbg(hw, "Failed to write, error %x\n", error);
-		return IXGBE_ERR_PHY;
+		return -EIO;
 	}
 
 out:
@@ -1558,7 +1561,7 @@
 
 	/* iXFI is only supported with X552 */
 	if (mac->type != ixgbe_mac_X550EM_x)
-		return IXGBE_ERR_LINK_SETUP;
+		return -EIO;
 
 	/* Disable AN and force speed to 10G Serial. */
 	status = ixgbe_read_iosf_sb_reg_x550(hw,
@@ -1580,7 +1583,7 @@
 		break;
 	default:
 		/* Other link speeds are not supported by internal KR PHY. */
-		return IXGBE_ERR_LINK_SETUP;
+		return -EINVAL;
 	}
 
 	status = ixgbe_write_iosf_sb_reg_x550(hw,
@@ -1611,7 +1614,7 @@
 {
 	switch (hw->phy.sfp_type) {
 	case ixgbe_sfp_type_not_present:
-		return IXGBE_ERR_SFP_NOT_PRESENT;
+		return -ENOENT;
 	case ixgbe_sfp_type_da_cu_core0:
 	case ixgbe_sfp_type_da_cu_core1:
 		*linear = true;
@@ -1630,7 +1633,7 @@
 	case ixgbe_sfp_type_1g_cu_core0:
 	case ixgbe_sfp_type_1g_cu_core1:
 	default:
-		return IXGBE_ERR_SFP_NOT_SUPPORTED;
+		return -EOPNOTSUPP;
 	}
 
 	return 0;
@@ -1660,7 +1663,7 @@
 	 * there is no reason to configure CS4227 and SFP not present error is
 	 * not accepted in the setup MAC link flow.
 	 */
-	if (status == IXGBE_ERR_SFP_NOT_PRESENT)
+	if (status == -ENOENT)
 		return 0;
 
 	if (status)
@@ -1718,7 +1721,7 @@
 		break;
 	default:
 		/* Other link speeds are not supported by internal PHY. */
-		return IXGBE_ERR_LINK_SETUP;
+		return -EINVAL;
 	}
 
 	status = mac->ops.write_iosf_sb_reg(hw,
@@ -1753,7 +1756,7 @@
 	/* If no SFP module present, then return success. Return success since
 	 * SFP not present error is not excepted in the setup MAC link flow.
 	 */
-	if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT)
+	if (ret_val == -ENOENT)
 		return 0;
 
 	if (ret_val)
@@ -1803,7 +1806,7 @@
 	/* If no SFP module present, then return success. Return success since
 	 * SFP not present error is not excepted in the setup MAC link flow.
 	 */
-	if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT)
+	if (ret_val == -ENOENT)
 		return 0;
 
 	if (ret_val)
@@ -1813,7 +1816,7 @@
 	ixgbe_setup_kr_speed_x550em(hw, speed);
 
 	if (hw->phy.mdio.prtad == MDIO_PRTAD_NONE)
-		return IXGBE_ERR_PHY_ADDR_INVALID;
+		return -EFAULT;
 
 	/* Get external PHY SKU id */
 	ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_EFUSE_PDF_SKU,
@@ -1912,7 +1915,7 @@
 	u16 i, autoneg_status;
 
 	if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 
 	status = ixgbe_check_mac_link_generic(hw, speed, link_up,
 					      link_up_wait_to_complete);
@@ -2095,9 +2098,9 @@
  */
 static void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw)
 {
-	s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
 	u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
 	ixgbe_link_speed speed;
+	s32 status = -EIO;
 	bool link_up;
 
 	/* AN should have completed when the cable was plugged in.
@@ -2115,7 +2118,7 @@
 	/* Check if auto-negotiation has completed */
 	status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info);
 	if (status || !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) {
-		status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+		status = -EIO;
 		goto out;
 	}
 
@@ -2319,18 +2322,18 @@
  * @hw: pointer to hardware structure
  * @lsc: pointer to boolean flag which indicates whether external Base T
  *	 PHY interrupt is lsc
+ * @is_overtemp: indicate whether an overtemp event encountered
  *
  * Determime if external Base T PHY interrupt cause is high temperature
  * failure alarm or link status change.
- *
- * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
- * failure alarm, else return PHY access status.
  **/
-static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc)
+static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc,
+				       bool *is_overtemp)
 {
 	u32 status;
 	u16 reg;
 
+	*is_overtemp = false;
 	*lsc = false;
 
 	/* Vendor alarm triggered */
@@ -2362,7 +2365,8 @@
 	if (reg & IXGBE_MDIO_GLOBAL_ALM_1_HI_TMP_FAIL) {
 		/* power down the PHY in case the PHY FW didn't already */
 		ixgbe_set_copper_phy_power(hw, false);
-		return IXGBE_ERR_OVERTEMP;
+		*is_overtemp = true;
+		return -EIO;
 	}
 	if (reg & IXGBE_MDIO_GLOBAL_ALM_1_DEV_FAULT) {
 		/*  device fault alarm triggered */
@@ -2376,7 +2380,8 @@
 		if (reg == IXGBE_MDIO_GLOBAL_FAULT_MSG_HI_TMP) {
 			/* power down the PHY in case the PHY FW didn't */
 			ixgbe_set_copper_phy_power(hw, false);
-			return IXGBE_ERR_OVERTEMP;
+			*is_overtemp = true;
+			return -EIO;
 		}
 	}
 
@@ -2412,12 +2417,12 @@
  **/
 static s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw)
 {
+	bool lsc, overtemp;
 	u32 status;
 	u16 reg;
-	bool lsc;
 
 	/* Clear interrupt flags */
-	status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
+	status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc, &overtemp);
 
 	/* Enable link status change alarm */
 
@@ -2496,21 +2501,20 @@
 /**
  * ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt
  * @hw: pointer to hardware structure
+ * @is_overtemp: indicate whether an overtemp event encountered
  *
  * Handle external Base T PHY interrupt. If high temperature
  * failure alarm then return error, else if link status change
  * then setup internal/external PHY link
- *
- * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
- * failure alarm, else return PHY access status.
  **/
-static s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw)
+static s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw,
+					  bool *is_overtemp)
 {
 	struct ixgbe_phy_info *phy = &hw->phy;
 	bool lsc;
 	u32 status;
 
-	status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
+	status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc, is_overtemp);
 	if (status)
 		return status;
 
@@ -2642,7 +2646,7 @@
 	u16 speed;
 
 	if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 
 	if (!(hw->mac.type == ixgbe_mac_X550EM_x &&
 	      !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE))) {
@@ -2685,7 +2689,7 @@
 		break;
 	default:
 		/* Internal PHY does not support anything else */
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 	}
 
 	return ixgbe_setup_ixfi_x550em(hw, &force_speed);
@@ -2717,7 +2721,7 @@
 	u16 phy_data;
 
 	if (led_idx >= IXGBE_X557_MAX_LED_INDEX)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* To turn on the LED, set mode to ON. */
 	hw->phy.ops.read_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx,
@@ -2739,7 +2743,7 @@
 	u16 phy_data;
 
 	if (led_idx >= IXGBE_X557_MAX_LED_INDEX)
-		return IXGBE_ERR_PARAM;
+		return -EINVAL;
 
 	/* To turn on the LED, set mode to ON. */
 	hw->phy.ops.read_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx,
@@ -2763,8 +2767,9 @@
  *
  *  Sends driver version number to firmware through the manageability
  *  block.  On success return 0
- *  else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring
- *  semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ *  else returns -EBUSY when encountering an error acquiring
+ *  semaphore, -EIO when command fails or -ENIVAL when incorrect
+ *  params passed.
  **/
 static s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min,
 				     u8 build, u8 sub, u16 len,
@@ -2775,7 +2780,7 @@
 	int i;
 
 	if (!len || !driver_ver || (len > sizeof(fw_cmd.driver_string)))
-		return IXGBE_ERR_INVALID_ARGUMENT;
+		return -EINVAL;
 
 	fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
 	fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN + len;
@@ -2800,7 +2805,7 @@
 
 		if (fw_cmd.hdr.cmd_or_resp.ret_status !=
 		    FW_CEM_RESP_STATUS_SUCCESS)
-			return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+			return -EIO;
 		return 0;
 	}
 
@@ -2857,7 +2862,7 @@
 	/* Validate the requested mode */
 	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
 		hw_err(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 	}
 
 	/* 10gig parts do not have a word in the EEPROM to determine the
@@ -2892,7 +2897,7 @@
 		break;
 	default:
 		hw_err(hw, "Flow control param set incorrectly\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	switch (hw->device_id) {
@@ -2936,8 +2941,8 @@
 static void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw)
 {
 	u32 link_s1, lp_an_page_low, an_cntl_1;
-	s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
 	ixgbe_link_speed speed;
+	s32 status = -EIO;
 	bool link_up;
 
 	/* AN should have completed when the cable was plugged in.
@@ -2963,7 +2968,7 @@
 
 	if (status || (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) {
 		hw_dbg(hw, "Auto-Negotiation did not complete\n");
-		status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+		status = -EIO;
 		goto out;
 	}
 
@@ -3137,21 +3142,23 @@
 /**
  * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp
  * @hw: pointer to hardware structure
+ *
+ * Return true when an overtemp event detected, otherwise false.
  */
-static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw)
+static bool ixgbe_check_overtemp_fw(struct ixgbe_hw *hw)
 {
 	u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
 	s32 rc;
 
 	rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store);
 	if (rc)
-		return rc;
+		return false;
 
 	if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) {
 		ixgbe_shutdown_fw_phy(hw);
-		return IXGBE_ERR_OVERTEMP;
+		return true;
 	}
-	return 0;
+	return false;
 }
 
 /**
@@ -3201,8 +3208,7 @@
 
 	/* Identify the PHY or SFP module */
 	ret_val = phy->ops.identify(hw);
-	if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED ||
-	    ret_val == IXGBE_ERR_PHY_ADDR_INVALID)
+	if (ret_val == -EOPNOTSUPP || ret_val == -EFAULT)
 		return ret_val;
 
 	/* Setup function pointers based on detected hardware */
@@ -3405,10 +3411,12 @@
 	/* flush pending Tx transactions */
 	ixgbe_clear_tx_pending(hw);
 
+	/* set MDIO speed before talking to the PHY in case it's the 1st time */
+	ixgbe_set_mdio_speed(hw);
+
 	/* PHY ops must be identified and initialized prior to reset */
 	status = hw->phy.ops.init(hw);
-	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED ||
-	    status == IXGBE_ERR_PHY_ADDR_INVALID)
+	if (status == -EOPNOTSUPP || status == -EFAULT)
 		return status;
 
 	/* start the external PHY */
@@ -3424,7 +3432,7 @@
 		hw->phy.sfp_setup_needed = false;
 	}
 
-	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+	if (status == -EOPNOTSUPP)
 		return status;
 
 	/* Reset PHY */
@@ -3448,7 +3456,7 @@
 	status = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask);
 	if (status) {
 		hw_dbg(hw, "semaphore failed with %d", status);
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 	}
 
 	ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL);
@@ -3466,7 +3474,7 @@
 	}
 
 	if (ctrl & IXGBE_CTRL_RST_MASK) {
-		status = IXGBE_ERR_RESET_FAILED;
+		status = -EIO;
 		hw_dbg(hw, "Reset polling failed to complete.\n");
 	}
 
@@ -3562,7 +3570,7 @@
 	/* Validate the requested mode */
 	if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
 		hw_err(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
-		return IXGBE_ERR_INVALID_LINK_SETTINGS;
+		return -EINVAL;
 	}
 
 	if (hw->fc.requested_mode == ixgbe_fc_default)
@@ -3619,7 +3627,7 @@
 		break;
 	default:
 		hw_err(hw, "Flow control param set incorrectly\n");
-		return IXGBE_ERR_CONFIG;
+		return -EIO;
 	}
 
 	status = hw->mac.ops.write_iosf_sb_reg(hw,
@@ -3715,7 +3723,7 @@
 			return 0;
 		if (hmask)
 			ixgbe_release_swfw_sync_X540(hw, hmask);
-		if (status != IXGBE_ERR_TOKEN_RETRY)
+		if (status != -EAGAIN)
 			return status;
 		msleep(FW_PHY_TOKEN_DELAY);
 	}
@@ -3759,7 +3767,7 @@
 	s32 status;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, mask))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = hw->phy.ops.read_reg_mdi(hw, reg_addr, device_type, phy_data);
 
@@ -3785,7 +3793,7 @@
 	s32 status;
 
 	if (hw->mac.ops.acquire_swfw_sync(hw, mask))
-		return IXGBE_ERR_SWFW_SYNC;
+		return -EBUSY;
 
 	status = ixgbe_write_phy_reg_mdi(hw, reg_addr, device_type, phy_data);
 	hw->mac.ops.release_swfw_sync(hw, mask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbe/ixgbe_xsk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbe/ixgbe_xsk.c
@@ -201,26 +201,28 @@
 }
 
 static struct sk_buff *ixgbe_construct_skb_zc(struct ixgbe_ring *rx_ring,
-					      struct ixgbe_rx_buffer *bi)
+					      const struct xdp_buff *xdp)
 {
-	unsigned int metasize = bi->xdp->data - bi->xdp->data_meta;
-	unsigned int datasize = bi->xdp->data_end - bi->xdp->data;
+	unsigned int totalsize = xdp->data_end - xdp->data_meta;
+	unsigned int metasize = xdp->data - xdp->data_meta;
 	struct sk_buff *skb;
 
+	net_prefetch(xdp->data_meta);
+
 	/* allocate a skb to store the frags */
-	skb = __napi_alloc_skb(&rx_ring->q_vector->napi,
-			       bi->xdp->data_end - bi->xdp->data_hard_start,
+	skb = __napi_alloc_skb(&rx_ring->q_vector->napi, totalsize,
 			       GFP_ATOMIC | __GFP_NOWARN);
 	if (unlikely(!skb))
 		return NULL;
 
-	skb_reserve(skb, bi->xdp->data - bi->xdp->data_hard_start);
-	memcpy(__skb_put(skb, datasize), bi->xdp->data, datasize);
-	if (metasize)
+	memcpy(__skb_put(skb, totalsize), xdp->data_meta,
+	       ALIGN(totalsize, sizeof(long)));
+
+	if (metasize) {
 		skb_metadata_set(skb, metasize);
+		__skb_pull(skb, metasize);
+	}
 
-	xsk_buff_free(bi->xdp);
-	bi->xdp = NULL;
 	return skb;
 }
 
@@ -311,12 +313,15 @@
 		}
 
 		/* XDP_PASS path */
-		skb = ixgbe_construct_skb_zc(rx_ring, bi);
+		skb = ixgbe_construct_skb_zc(rx_ring, bi->xdp);
 		if (!skb) {
 			rx_ring->rx_stats.alloc_rx_buff_failed++;
 			break;
 		}
 
+		xsk_buff_free(bi->xdp);
+		bi->xdp = NULL;
+
 		cleaned_count++;
 		ixgbe_inc_ntc(rx_ring);
 
@@ -388,12 +393,14 @@
 	u32 cmd_type;
 
 	while (budget-- > 0) {
-		if (unlikely(!ixgbe_desc_unused(xdp_ring)) ||
-		    !netif_carrier_ok(xdp_ring->netdev)) {
+		if (unlikely(!ixgbe_desc_unused(xdp_ring))) {
 			work_done = false;
 			break;
 		}
 
+		if (!netif_carrier_ok(xdp_ring->netdev))
+			break;
+
 		if (!xsk_tx_peek_desc(pool, &desc))
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbevf/ixgbevf.h
@@ -387,6 +387,8 @@
 	u32 *rss_key;
 	u8 rss_indir_tbl[IXGBEVF_X550_VFRETA_SIZE];
 	u32 flags;
+	bool link_state;
+
 #define IXGBEVF_FLAGS_LEGACY_RX		BIT(1)
 
 #ifdef CONFIG_XFRM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -1984,14 +1984,15 @@
 	if (adapter->flags & IXGBEVF_FLAGS_LEGACY_RX)
 		return;
 
-	set_ring_build_skb_enabled(rx_ring);
+	if (PAGE_SIZE < 8192)
+		if (max_frame > IXGBEVF_MAX_FRAME_BUILD_SKB)
+			set_ring_uses_large_buffer(rx_ring);
 
-	if (PAGE_SIZE < 8192) {
-		if (max_frame <= IXGBEVF_MAX_FRAME_BUILD_SKB)
-			return;
+	/* 82599 can't rely on RXDCTL.RLPML to restrict the size of the frame */
+	if (adapter->hw.mac.type == ixgbe_mac_82599_vf && !ring_uses_large_buffer(rx_ring))
+		return;
 
-		set_ring_uses_large_buffer(rx_ring);
-	}
+	set_ring_build_skb_enabled(rx_ring);
 }
 
 /**
@@ -2290,7 +2291,9 @@
 static void ixgbevf_up_complete(struct ixgbevf_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
+	struct pci_dev *pdev = adapter->pdev;
 	struct ixgbe_hw *hw = &adapter->hw;
+	bool state;
 
 	ixgbevf_configure_msix(adapter);
 
@@ -2303,6 +2306,11 @@
 
 	spin_unlock_bh(&adapter->mbx_lock);
 
+	state = adapter->link_state;
+	hw->mac.ops.get_link_state(hw, &adapter->link_state);
+	if (state && state != adapter->link_state)
+		dev_info(&pdev->dev, "VF is administratively disabled\n");
+
 	smp_mb__before_atomic();
 	clear_bit(__IXGBEVF_DOWN, &adapter->state);
 	ixgbevf_napi_enable_all(adapter);
@@ -2540,7 +2548,7 @@
 	}
 
 	if (is_valid_ether_addr(adapter->hw.mac.addr)) {
-		ether_addr_copy(netdev->dev_addr, adapter->hw.mac.addr);
+		eth_hw_addr_set(netdev, adapter->hw.mac.addr);
 		ether_addr_copy(netdev->perm_addr, adapter->hw.mac.addr);
 	}
 
@@ -3054,7 +3062,7 @@
 		else if (is_zero_ether_addr(adapter->hw.mac.addr))
 			dev_info(&pdev->dev,
 				 "MAC address not assigned by administrator.\n");
-		ether_addr_copy(netdev->dev_addr, hw->mac.addr);
+		eth_hw_addr_set(netdev, hw->mac.addr);
 	}
 
 	if (!is_valid_ether_addr(netdev->dev_addr)) {
@@ -3072,6 +3080,8 @@
 	adapter->tx_ring_count = IXGBEVF_DEFAULT_TXD;
 	adapter->rx_ring_count = IXGBEVF_DEFAULT_RXD;
 
+	adapter->link_state = true;
+
 	set_bit(__IXGBEVF_DOWN, &adapter->state);
 	return 0;
 
@@ -3304,7 +3314,7 @@
 
 	ixgbevf_watchdog_update_link(adapter);
 
-	if (adapter->link_up)
+	if (adapter->link_up && adapter->link_state)
 		ixgbevf_watchdog_link_is_up(adapter);
 	else
 		ixgbevf_watchdog_link_is_down(adapter);
@@ -4231,7 +4241,7 @@
 
 	ether_addr_copy(hw->mac.addr, addr->sa_data);
 	ether_addr_copy(hw->mac.perm_addr, addr->sa_data);
-	ether_addr_copy(netdev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(netdev, addr->sa_data);
 
 	return 0;
 }
@@ -4858,6 +4868,8 @@
  **/
 static int __init ixgbevf_init_module(void)
 {
+	int err;
+
 	pr_info("%s\n", ixgbevf_driver_string);
 	pr_info("%s\n", ixgbevf_copyright);
 	ixgbevf_wq = create_singlethread_workqueue(ixgbevf_driver_name);
@@ -4866,7 +4878,13 @@
 		return -ENOMEM;
 	}
 
-	return pci_register_driver(&ixgbevf_driver);
+	err = pci_register_driver(&ixgbevf_driver);
+	if (err) {
+		destroy_workqueue(ixgbevf_wq);
+		return err;
+	}
+
+	return 0;
 }
 
 module_init(ixgbevf_init_module);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbevf/mbx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbevf/mbx.h
@@ -51,6 +51,16 @@
 /* bits 23:16 are used for exra info for certain messages */
 #define IXGBE_VT_MSGINFO_MASK	(0xFF << IXGBE_VT_MSGINFO_SHIFT)
 
+/* IXGBE_VT_MSGTYPE_NACK and IXGBE_VT_MSGTYPE_ACK were renamed to
+ * IXGBE_VT_MSGTYPE_FAILURE and IXGBE_VT_MSGTYPE_SUCCESS respectively
+ * with commit 0edbecd57057 upstream.
+ *
+ * One of the backported fixes use them with their new names. These
+ * aliases enable them to work with both older and newer names.
+ */
+#define IXGBE_VT_MSGTYPE_SUCCESS IXGBE_VT_MSGTYPE_ACK
+#define IXGBE_VT_MSGTYPE_FAILURE IXGBE_VT_MSGTYPE_NACK
+
 /* definitions to support mailbox API version negotiation */
 
 /* each element denotes a version of the API; existing numbers may not
@@ -97,6 +107,8 @@
 #define IXGBE_VF_IPSEC_ADD	0x0d
 #define IXGBE_VF_IPSEC_DEL	0x0e
 
+#define IXGBE_VF_GET_LINK_STATE 0x10 /* get vf link state */
+
 /* length of permanent address message returned from PF */
 #define IXGBE_VF_PERMADDR_MSG_LEN	4
 /* word in permanent address message with the current multicast type */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbevf/vf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbevf/vf.c
@@ -580,6 +580,46 @@
 }
 
 /**
+ * ixgbevf_get_link_state_vf - Get VF link state from PF
+ * @hw: pointer to the HW structure
+ * @link_state: link state storage
+ *
+ * Returns state of the operation error or success.
+ */
+static s32 ixgbevf_get_link_state_vf(struct ixgbe_hw *hw, bool *link_state)
+{
+	u32 msgbuf[2];
+	s32 ret_val;
+	s32 err;
+
+	msgbuf[0] = IXGBE_VF_GET_LINK_STATE;
+	msgbuf[1] = 0x0;
+
+	err = ixgbevf_write_msg_read_ack(hw, msgbuf, msgbuf, 2);
+
+	if (err || (msgbuf[0] & IXGBE_VT_MSGTYPE_FAILURE)) {
+		ret_val = IXGBE_ERR_MBX;
+	} else {
+		ret_val = 0;
+		*link_state = msgbuf[1];
+	}
+
+	return ret_val;
+}
+
+/**
+ * ixgbevf_hv_get_link_state_vf - * Hyper-V variant - just a stub.
+ * @hw: unused
+ * @link_state: unused
+ *
+ * Hyper-V variant; there is no mailbox communication.
+ */
+static s32 ixgbevf_hv_get_link_state_vf(struct ixgbe_hw *hw, bool *link_state)
+{
+	return -EOPNOTSUPP;
+}
+
+/**
  *  ixgbevf_set_vfta_vf - Set/Unset VLAN filter table address
  *  @hw: pointer to the HW structure
  *  @vlan: 12 bit VLAN ID
@@ -958,6 +998,7 @@
 	.set_rar		= ixgbevf_set_rar_vf,
 	.update_mc_addr_list	= ixgbevf_update_mc_addr_list_vf,
 	.update_xcast_mode	= ixgbevf_update_xcast_mode,
+	.get_link_state		= ixgbevf_get_link_state_vf,
 	.set_uc_addr		= ixgbevf_set_uc_addr_vf,
 	.set_vfta		= ixgbevf_set_vfta_vf,
 	.set_rlpml		= ixgbevf_set_rlpml_vf,
@@ -975,6 +1016,7 @@
 	.set_rar		= ixgbevf_hv_set_rar_vf,
 	.update_mc_addr_list	= ixgbevf_hv_update_mc_addr_list_vf,
 	.update_xcast_mode	= ixgbevf_hv_update_xcast_mode,
+	.get_link_state		= ixgbevf_hv_get_link_state_vf,
 	.set_uc_addr		= ixgbevf_hv_set_uc_addr_vf,
 	.set_vfta		= ixgbevf_hv_set_vfta_vf,
 	.set_rlpml		= ixgbevf_hv_set_rlpml_vf,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/intel/ixgbevf/vf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/intel/ixgbevf/vf.h
@@ -39,6 +39,7 @@
 	s32 (*init_rx_addrs)(struct ixgbe_hw *);
 	s32 (*update_mc_addr_list)(struct ixgbe_hw *, struct net_device *);
 	s32 (*update_xcast_mode)(struct ixgbe_hw *, int);
+	s32 (*get_link_state)(struct ixgbe_hw *hw, bool *link_state);
 	s32 (*enable_mc)(struct ixgbe_hw *);
 	s32 (*disable_mc)(struct ixgbe_hw *);
 	s32 (*clear_vfta)(struct ixgbe_hw *);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/jme.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/jme.c
@@ -945,15 +945,13 @@
 	if (skb->protocol != htons(ETH_P_IP))
 		return csum;
 	skb_set_network_header(skb, ETH_HLEN);
-	if ((ip_hdr(skb)->protocol != IPPROTO_UDP) ||
-	    (skb->len < (ETH_HLEN +
-			(ip_hdr(skb)->ihl << 2) +
-			sizeof(struct udphdr)))) {
+
+	if (ip_hdr(skb)->protocol != IPPROTO_UDP ||
+	    skb->len < (ETH_HLEN + ip_hdrlen(skb) + sizeof(struct udphdr))) {
 		skb_reset_network_header(skb);
 		return csum;
 	}
-	skb_set_transport_header(skb,
-			ETH_HLEN + (ip_hdr(skb)->ihl << 2));
+	skb_set_transport_header(skb, ETH_HLEN + ip_hdrlen(skb));
 	csum = udp_hdr(skb)->check;
 	skb_reset_transport_header(skb);
 	skb_reset_network_header(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/korina.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/korina.c
@@ -1297,15 +1297,14 @@
 	lp = netdev_priv(dev);
 
 	if (mac_addr)
-		ether_addr_copy(dev->dev_addr, mac_addr);
-	else if (of_get_mac_address(pdev->dev.of_node, dev->dev_addr) < 0)
+		eth_hw_addr_set(dev, mac_addr);
+	else if (of_get_ethdev_address(pdev->dev.of_node, dev) < 0)
 		eth_hw_addr_random(dev);
 
-	clk = devm_clk_get_optional(&pdev->dev, "mdioclk");
+	clk = devm_clk_get_optional_enabled(&pdev->dev, "mdioclk");
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
 	if (clk) {
-		clk_prepare_enable(clk);
 		lp->mii_clock_freq = clk_get_rate(clk);
 	} else {
 		lp->mii_clock_freq = 200000000; /* max possible input clk */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/lantiq_etop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/lantiq_etop.c
@@ -213,8 +213,9 @@
 	if (ch->dma.irq)
 		free_irq(ch->dma.irq, priv);
 	if (IS_RX(ch->idx)) {
-		int desc;
-		for (desc = 0; desc < LTQ_DESC_NUM; desc++)
+		struct ltq_dma_channel *dma = &ch->dma;
+
+		for (dma->desc = 0; dma->desc < LTQ_DESC_NUM; dma->desc++)
 			dev_kfree_skb_any(ch->skb[ch->dma.desc]);
 	}
 }
@@ -463,10 +464,11 @@
 	unsigned long flags;
 	u32 byte_offset;
 
-	len = skb->len < ETH_ZLEN ? ETH_ZLEN : skb->len;
+	if (skb_put_padto(skb, ETH_ZLEN))
+		return NETDEV_TX_OK;
+	len = skb->len;
 
 	if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ch->skb[ch->dma.desc]) {
-		dev_kfree_skb_any(skb);
 		netdev_err(dev, "tx ring full\n");
 		netif_tx_stop_queue(txq);
 		return NETDEV_TX_BUSY;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/lantiq_xrx200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/lantiq_xrx200.c
@@ -209,7 +209,7 @@
 	skb->protocol = eth_type_trans(skb, net_dev);
 	netif_receive_skb(skb);
 	net_dev->stats.rx_packets++;
-	net_dev->stats.rx_bytes += len - ETH_FCS_LEN;
+	net_dev->stats.rx_bytes += len;
 
 	return 0;
 }
@@ -474,7 +474,7 @@
 		return PTR_ERR(priv->clk);
 	}
 
-	err = of_get_mac_address(np, net_dev->dev_addr);
+	err = of_get_ethdev_address(np, net_dev);
 	if (err)
 		eth_hw_addr_random(net_dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/litex/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/litex/Kconfig
@@ -17,7 +17,7 @@
 
 config LITEX_LITEETH
 	tristate "LiteX Ethernet support"
-	depends on OF_NET
+	depends on OF && HAS_IOMEM
 	help
 	  If you wish to compile a kernel for hardware with a LiteX LiteEth
 	  device then you should answer Y to this.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/litex/litex_liteeth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/litex/litex_liteeth.c
@@ -266,7 +266,7 @@
 	priv->tx_base = buf_base + priv->num_rx_slots * priv->slot_size;
 	priv->tx_slot = 0;
 
-	err = of_get_mac_address(pdev->dev.of_node, netdev->dev_addr);
+	err = of_get_ethdev_address(pdev->dev.of_node, netdev);
 	if (err)
 		eth_hw_addr_random(netdev);
 
@@ -289,7 +289,6 @@
 	struct net_device *netdev = platform_get_drvdata(pdev);
 
 	unregister_netdev(netdev);
-	free_netdev(netdev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mv643xx_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mv643xx_eth.c
@@ -1770,7 +1770,7 @@
 	addr[5] = mac_l & 0xff;
 }
 
-static void uc_addr_set(struct mv643xx_eth_private *mp, unsigned char *addr)
+static void uc_addr_set(struct mv643xx_eth_private *mp, const u8 *addr)
 {
 	wrlp(mp, MAC_ADDR_HIGH,
 		(addr[0] << 24) | (addr[1] << 16) | (addr[2] << 8) | addr[3]);
@@ -2477,6 +2477,7 @@
 	for (i = 0; i < mp->rxq_count; i++)
 		rxq_deinit(mp->rxq + i);
 out:
+	napi_disable(&mp->napi);
 	free_irq(dev->irq, dev);
 
 	return err;
@@ -2700,6 +2701,22 @@
 
 static struct platform_device *port_platdev[3];
 
+static void mv643xx_eth_shared_of_remove(void)
+{
+	struct mv643xx_eth_platform_data *pd;
+	int n;
+
+	for (n = 0; n < 3; n++) {
+		if (!port_platdev[n])
+			continue;
+		pd = dev_get_platdata(&port_platdev[n]->dev);
+		if (pd)
+			of_node_put(pd->phy_node);
+		platform_device_del(port_platdev[n]);
+		port_platdev[n] = NULL;
+	}
+}
+
 static int mv643xx_eth_shared_of_add_port(struct platform_device *pdev,
 					  struct device_node *pnp)
 {
@@ -2736,7 +2753,9 @@
 		return -EINVAL;
 	}
 
-	of_get_mac_address(pnp, ppd.mac_addr);
+	ret = of_get_mac_address(pnp, ppd.mac_addr);
+	if (ret == -EPROBE_DEFER)
+		return ret;
 
 	mv643xx_eth_property(pnp, "tx-queue-size", ppd.tx_queue_size);
 	mv643xx_eth_property(pnp, "tx-sram-addr", ppd.tx_sram_addr);
@@ -2753,8 +2772,10 @@
 	}
 
 	ppdev = platform_device_alloc(MV643XX_ETH_NAME, dev_num);
-	if (!ppdev)
-		return -ENOMEM;
+	if (!ppdev) {
+		ret = -ENOMEM;
+		goto put_err;
+	}
 	ppdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
 	ppdev->dev.of_node = pnp;
 
@@ -2776,6 +2797,8 @@
 
 port_err:
 	platform_device_put(ppdev);
+put_err:
+	of_node_put(ppd.phy_node);
 	return ret;
 }
 
@@ -2800,21 +2823,13 @@
 		ret = mv643xx_eth_shared_of_add_port(pdev, pnp);
 		if (ret) {
 			of_node_put(pnp);
+			mv643xx_eth_shared_of_remove();
 			return ret;
 		}
 	}
 	return 0;
 }
 
-static void mv643xx_eth_shared_of_remove(void)
-{
-	int n;
-
-	for (n = 0; n < 3; n++) {
-		platform_device_del(port_platdev[n]);
-		port_platdev[n] = NULL;
-	}
-}
 #else
 static inline int mv643xx_eth_shared_of_probe(struct platform_device *pdev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvmdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvmdio.c
@@ -429,12 +429,14 @@
 };
 MODULE_DEVICE_TABLE(of, orion_mdio_match);
 
+#ifdef CONFIG_ACPI
 static const struct acpi_device_id orion_mdio_acpi_match[] = {
 	{ "MRVL0100", BUS_TYPE_SMI },
 	{ "MRVL0101", BUS_TYPE_XSMI },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, orion_mdio_acpi_match);
+#endif
 
 static struct platform_driver orion_mdio_driver = {
 	.probe = orion_mdio_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvneta.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvneta.c
@@ -1474,7 +1474,7 @@
 			 */
 			if (txq_number == 1)
 				txq_map = (cpu == pp->rxq_def) ?
-					MVNETA_CPU_TXQ_ACCESS(1) : 0;
+					MVNETA_CPU_TXQ_ACCESS(0) : 0;
 
 		} else {
 			txq_map = MVNETA_CPU_TXQ_ACCESS_ALL_MASK;
@@ -1623,8 +1623,8 @@
 }
 
 /* Set mac address */
-static void mvneta_mac_addr_set(struct mvneta_port *pp, unsigned char *addr,
-				int queue)
+static void mvneta_mac_addr_set(struct mvneta_port *pp,
+				const unsigned char *addr, int queue)
 {
 	unsigned int mac_h;
 	unsigned int mac_l;
@@ -4162,7 +4162,7 @@
 	/* Use the cpu associated to the rxq when it is online, in all
 	 * the other cases, use the cpu 0 which can't be offline.
 	 */
-	if (cpu_online(pp->rxq_def))
+	if (pp->rxq_def < nr_cpu_ids && cpu_online(pp->rxq_def))
 		elected_cpu = pp->rxq_def;
 
 	max_cpu = num_present_cpus();
@@ -4185,7 +4185,7 @@
 		 */
 		if (txq_number == 1)
 			txq_map = (cpu == elected_cpu) ?
-				MVNETA_CPU_TXQ_ACCESS(1) : 0;
+				MVNETA_CPU_TXQ_ACCESS(0) : 0;
 		else
 			txq_map = mvreg_read(pp, MVNETA_CPU_MAP(cpu)) &
 				MVNETA_CPU_TXQ_ACCESS_ALL_MASK;
@@ -5242,7 +5242,7 @@
 		goto err_free_ports;
 	}
 
-	err = of_get_mac_address(dn, dev->dev_addr);
+	err = of_get_ethdev_address(dn, dev);
 	if (!err) {
 		mac_from = "device tree";
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -1088,7 +1088,7 @@
 	unsigned int max_port_rxqs;
 
 	/* Workqueue to gather hardware statistics */
-	char queue_name[30];
+	char queue_name[31];
 	struct workqueue_struct *stats_queue;
 
 	/* Debugfs root entry */
@@ -1108,6 +1108,9 @@
 
 	/* Spinlocks for CM3 shared memory configuration */
 	spinlock_t mss_spinlock;
+
+	/* Spinlock for shared PRS parser memory and shadow table */
+	spinlock_t prs_spinlock;
 };
 
 struct mvpp2_pcpu_stats {
@@ -1529,6 +1532,7 @@
 void mvpp2_dbgfs_init(struct mvpp2 *priv, const char *name);
 
 void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
+void mvpp2_dbgfs_exit(void);
 
 void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c
@@ -62,35 +62,38 @@
 	MVPP2_DEF_FLOW(MVPP22_FLOW_TCP4, MVPP2_FL_IP4_TCP_FRAG_UNTAG,
 		       MVPP22_CLS_HEK_IP4_2T,
 		       MVPP2_PRS_RI_VLAN_NONE | MVPP2_PRS_RI_L3_IP4 |
-		       MVPP2_PRS_RI_L4_TCP,
+		       MVPP2_PRS_RI_IP_FRAG_TRUE | MVPP2_PRS_RI_L4_TCP,
 		       MVPP2_PRS_IP_MASK | MVPP2_PRS_RI_VLAN_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_TCP4, MVPP2_FL_IP4_TCP_FRAG_UNTAG,
 		       MVPP22_CLS_HEK_IP4_2T,
 		       MVPP2_PRS_RI_VLAN_NONE | MVPP2_PRS_RI_L3_IP4_OPT |
-		       MVPP2_PRS_RI_L4_TCP,
+		       MVPP2_PRS_RI_IP_FRAG_TRUE | MVPP2_PRS_RI_L4_TCP,
 		       MVPP2_PRS_IP_MASK | MVPP2_PRS_RI_VLAN_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_TCP4, MVPP2_FL_IP4_TCP_FRAG_UNTAG,
 		       MVPP22_CLS_HEK_IP4_2T,
 		       MVPP2_PRS_RI_VLAN_NONE | MVPP2_PRS_RI_L3_IP4_OTHER |
-		       MVPP2_PRS_RI_L4_TCP,
+		       MVPP2_PRS_RI_IP_FRAG_TRUE | MVPP2_PRS_RI_L4_TCP,
 		       MVPP2_PRS_IP_MASK | MVPP2_PRS_RI_VLAN_MASK),
 
 	/* TCP over IPv4 flows, fragmented, with vlan tag */
 	MVPP2_DEF_FLOW(MVPP22_FLOW_TCP4, MVPP2_FL_IP4_TCP_FRAG_TAG,
 		       MVPP22_CLS_HEK_IP4_2T | MVPP22_CLS_HEK_TAGGED,
-		       MVPP2_PRS_RI_L3_IP4 | MVPP2_PRS_RI_L4_TCP,
+		       MVPP2_PRS_RI_L3_IP4 | MVPP2_PRS_RI_IP_FRAG_TRUE |
+			   MVPP2_PRS_RI_L4_TCP,
 		       MVPP2_PRS_IP_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_TCP4, MVPP2_FL_IP4_TCP_FRAG_TAG,
 		       MVPP22_CLS_HEK_IP4_2T | MVPP22_CLS_HEK_TAGGED,
-		       MVPP2_PRS_RI_L3_IP4_OPT | MVPP2_PRS_RI_L4_TCP,
+		       MVPP2_PRS_RI_L3_IP4_OPT | MVPP2_PRS_RI_IP_FRAG_TRUE |
+			   MVPP2_PRS_RI_L4_TCP,
 		       MVPP2_PRS_IP_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_TCP4, MVPP2_FL_IP4_TCP_FRAG_TAG,
 		       MVPP22_CLS_HEK_IP4_2T | MVPP22_CLS_HEK_TAGGED,
-		       MVPP2_PRS_RI_L3_IP4_OTHER | MVPP2_PRS_RI_L4_TCP,
+		       MVPP2_PRS_RI_L3_IP4_OTHER | MVPP2_PRS_RI_IP_FRAG_TRUE |
+			   MVPP2_PRS_RI_L4_TCP,
 		       MVPP2_PRS_IP_MASK),
 
 	/* UDP over IPv4 flows, Not fragmented, no vlan tag */
@@ -132,35 +135,38 @@
 	MVPP2_DEF_FLOW(MVPP22_FLOW_UDP4, MVPP2_FL_IP4_UDP_FRAG_UNTAG,
 		       MVPP22_CLS_HEK_IP4_2T,
 		       MVPP2_PRS_RI_VLAN_NONE | MVPP2_PRS_RI_L3_IP4 |
-		       MVPP2_PRS_RI_L4_UDP,
+		       MVPP2_PRS_RI_IP_FRAG_TRUE | MVPP2_PRS_RI_L4_UDP,
 		       MVPP2_PRS_IP_MASK | MVPP2_PRS_RI_VLAN_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_UDP4, MVPP2_FL_IP4_UDP_FRAG_UNTAG,
 		       MVPP22_CLS_HEK_IP4_2T,
 		       MVPP2_PRS_RI_VLAN_NONE | MVPP2_PRS_RI_L3_IP4_OPT |
-		       MVPP2_PRS_RI_L4_UDP,
+		       MVPP2_PRS_RI_IP_FRAG_TRUE | MVPP2_PRS_RI_L4_UDP,
 		       MVPP2_PRS_IP_MASK | MVPP2_PRS_RI_VLAN_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_UDP4, MVPP2_FL_IP4_UDP_FRAG_UNTAG,
 		       MVPP22_CLS_HEK_IP4_2T,
 		       MVPP2_PRS_RI_VLAN_NONE | MVPP2_PRS_RI_L3_IP4_OTHER |
-		       MVPP2_PRS_RI_L4_UDP,
+		       MVPP2_PRS_RI_IP_FRAG_TRUE | MVPP2_PRS_RI_L4_UDP,
 		       MVPP2_PRS_IP_MASK | MVPP2_PRS_RI_VLAN_MASK),
 
 	/* UDP over IPv4 flows, fragmented, with vlan tag */
 	MVPP2_DEF_FLOW(MVPP22_FLOW_UDP4, MVPP2_FL_IP4_UDP_FRAG_TAG,
 		       MVPP22_CLS_HEK_IP4_2T | MVPP22_CLS_HEK_TAGGED,
-		       MVPP2_PRS_RI_L3_IP4 | MVPP2_PRS_RI_L4_UDP,
+		       MVPP2_PRS_RI_L3_IP4 | MVPP2_PRS_RI_IP_FRAG_TRUE |
+			   MVPP2_PRS_RI_L4_UDP,
 		       MVPP2_PRS_IP_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_UDP4, MVPP2_FL_IP4_UDP_FRAG_TAG,
 		       MVPP22_CLS_HEK_IP4_2T | MVPP22_CLS_HEK_TAGGED,
-		       MVPP2_PRS_RI_L3_IP4_OPT | MVPP2_PRS_RI_L4_UDP,
+		       MVPP2_PRS_RI_L3_IP4_OPT | MVPP2_PRS_RI_IP_FRAG_TRUE |
+			   MVPP2_PRS_RI_L4_UDP,
 		       MVPP2_PRS_IP_MASK),
 
 	MVPP2_DEF_FLOW(MVPP22_FLOW_UDP4, MVPP2_FL_IP4_UDP_FRAG_TAG,
 		       MVPP22_CLS_HEK_IP4_2T | MVPP22_CLS_HEK_TAGGED,
-		       MVPP2_PRS_RI_L3_IP4_OTHER | MVPP2_PRS_RI_L4_UDP,
+		       MVPP2_PRS_RI_L3_IP4_OTHER | MVPP2_PRS_RI_IP_FRAG_TRUE |
+			   MVPP2_PRS_RI_L4_UDP,
 		       MVPP2_PRS_IP_MASK),
 
 	/* TCP over IPv6 flows, not fragmented, no vlan tag */
@@ -318,7 +324,7 @@
 		       MVPP2_PRS_RI_VLAN_MASK),
 	/* Non IP flow, with vlan tag */
 	MVPP2_DEF_FLOW(MVPP22_FLOW_ETHERNET, MVPP2_FL_NON_IP_TAG,
-		       MVPP22_CLS_HEK_OPT_VLAN,
+		       MVPP22_CLS_HEK_TAGGED,
 		       0, 0),
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvpp2/mvpp2_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvpp2/mvpp2_debugfs.c
@@ -691,6 +691,13 @@
 	return 0;
 }
 
+static struct dentry *mvpp2_root;
+
+void mvpp2_dbgfs_exit(void)
+{
+	debugfs_remove(mvpp2_root);
+}
+
 void mvpp2_dbgfs_cleanup(struct mvpp2 *priv)
 {
 	debugfs_remove_recursive(priv->dbgfs_dir);
@@ -700,10 +707,9 @@
 
 void mvpp2_dbgfs_init(struct mvpp2 *priv, const char *name)
 {
-	struct dentry *mvpp2_dir, *mvpp2_root;
+	struct dentry *mvpp2_dir;
 	int ret, i;
 
-	mvpp2_root = debugfs_lookup(MVPP2_DRIVER_NAME, NULL);
 	if (!mvpp2_root)
 		mvpp2_root = debugfs_create_dir(MVPP2_DRIVER_NAME, NULL);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -614,12 +614,38 @@
 	mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
 }
 
+/* Cleanup pool before actual initialization in the OS */
+static void mvpp2_bm_pool_cleanup(struct mvpp2 *priv, int pool_id)
+{
+	unsigned int thread = mvpp2_cpu_to_thread(priv, get_cpu());
+	u32 val;
+	int i;
+
+	/* Drain the BM from all possible residues left by firmware */
+	for (i = 0; i < MVPP2_BM_POOL_SIZE_MAX; i++)
+		mvpp2_thread_read(priv, thread, MVPP2_BM_PHY_ALLOC_REG(pool_id));
+
+	put_cpu();
+
+	/* Stop the BM pool */
+	val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(pool_id));
+	val |= MVPP2_BM_STOP_MASK;
+	mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(pool_id), val);
+}
+
 static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 {
 	enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
 	int i, err, poolnum = MVPP2_BM_POOLS_NUM;
 	struct mvpp2_port *port;
 
+	if (priv->percpu_pools)
+		poolnum = mvpp2_get_nrxqs(priv) * 2;
+
+	/* Clean up the pool state in case it contains stale state */
+	for (i = 0; i < poolnum; i++)
+		mvpp2_bm_pool_cleanup(priv, i);
+
 	if (priv->percpu_pools) {
 		for (i = 0; i < priv->port_count; i++) {
 			port = priv->port_list[i];
@@ -629,7 +655,6 @@
 			}
 		}
 
-		poolnum = mvpp2_get_nrxqs(priv) * 2;
 		for (i = 0; i < poolnum; i++) {
 			/* the pool in use */
 			int pn = i / (poolnum / 2);
@@ -928,13 +953,13 @@
 static void mvpp2_bm_pool_update_priv_fc(struct mvpp2 *priv, bool en)
 {
 	struct mvpp2_port *port;
-	int i;
+	int i, j;
 
 	for (i = 0; i < priv->port_count; i++) {
 		port = priv->port_list[i];
 		if (port->priv->percpu_pools) {
-			for (i = 0; i < port->nrxqs; i++)
-				mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[i],
+			for (j = 0; j < port->nrxqs; j++)
+				mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[j],
 							port->tx_fc & en);
 		} else {
 			mvpp2_bm_pool_update_fc(port, port->pool_long, port->tx_fc & en);
@@ -1605,7 +1630,7 @@
 	mvpp22_gop_fca_enable_periodic(port, true);
 }
 
-static int mvpp22_gop_init(struct mvpp2_port *port)
+static int mvpp22_gop_init(struct mvpp2_port *port, phy_interface_t interface)
 {
 	struct mvpp2 *priv = port->priv;
 	u32 val;
@@ -1613,7 +1638,7 @@
 	if (!priv->sysctrl_base)
 		return 0;
 
-	switch (port->phy_interface) {
+	switch (interface) {
 	case PHY_INTERFACE_MODE_RGMII:
 	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII_RXID:
@@ -1743,15 +1768,15 @@
  * lanes by the physical layer. This is why configurations like
  * "PPv2 (2500BaseX) - COMPHY (2500SGMII)" are valid.
  */
-static int mvpp22_comphy_init(struct mvpp2_port *port)
+static int mvpp22_comphy_init(struct mvpp2_port *port,
+			      phy_interface_t interface)
 {
 	int ret;
 
 	if (!port->comphy)
 		return 0;
 
-	ret = phy_set_mode_ext(port->comphy, PHY_MODE_ETHERNET,
-			       port->phy_interface);
+	ret = phy_set_mode_ext(port->comphy, PHY_MODE_ETHERNET, interface);
 	if (ret)
 		return ret;
 
@@ -2172,7 +2197,8 @@
 	writel(val & ~MVPP22_XPCS_CFG0_RESET_DIS, xpcs + MVPP22_XPCS_CFG0);
 }
 
-static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
+static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port,
+				      phy_interface_t interface)
 {
 	struct mvpp2 *priv = port->priv;
 	void __iomem *mpcs, *xpcs;
@@ -2184,7 +2210,7 @@
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
 	xpcs = priv->iface_base + MVPP22_XPCS_BASE(port->gop_id);
 
-	switch (port->phy_interface) {
+	switch (interface) {
 	case PHY_INTERFACE_MODE_10GBASER:
 		val = readl(mpcs + MVPP22_MPCS_CLK_RESET);
 		val |= MAC_CLK_RESET_MAC | MAC_CLK_RESET_SD_RX |
@@ -2959,11 +2985,11 @@
 	mvpp2_rxq_status_update(port, rxq->id, 0, rxq->size);
 
 	if (priv->percpu_pools) {
-		err = xdp_rxq_info_reg(&rxq->xdp_rxq_short, port->dev, rxq->id, 0);
+		err = xdp_rxq_info_reg(&rxq->xdp_rxq_short, port->dev, rxq->logic_rxq, 0);
 		if (err < 0)
 			goto err_free_dma;
 
-		err = xdp_rxq_info_reg(&rxq->xdp_rxq_long, port->dev, rxq->id, 0);
+		err = xdp_rxq_info_reg(&rxq->xdp_rxq_long, port->dev, rxq->logic_rxq, 0);
 		if (err < 0)
 			goto err_unregister_rxq_short;
 
@@ -4529,7 +4555,8 @@
 	return rx_done;
 }
 
-static void mvpp22_mode_reconfigure(struct mvpp2_port *port)
+static void mvpp22_mode_reconfigure(struct mvpp2_port *port,
+				    phy_interface_t interface)
 {
 	u32 ctrl3;
 
@@ -4540,18 +4567,18 @@
 	mvpp22_pcs_reset_assert(port);
 
 	/* comphy reconfiguration */
-	mvpp22_comphy_init(port);
+	mvpp22_comphy_init(port, interface);
 
 	/* gop reconfiguration */
-	mvpp22_gop_init(port);
+	mvpp22_gop_init(port, interface);
 
-	mvpp22_pcs_reset_deassert(port);
+	mvpp22_pcs_reset_deassert(port, interface);
 
 	if (mvpp2_port_supports_xlg(port)) {
 		ctrl3 = readl(port->base + MVPP22_XLG_CTRL3_REG);
 		ctrl3 &= ~MVPP22_XLG_CTRL3_MACMODESELECT_MASK;
 
-		if (mvpp2_is_xlg(port->phy_interface))
+		if (mvpp2_is_xlg(interface))
 			ctrl3 |= MVPP22_XLG_CTRL3_MACMODESELECT_10G;
 		else
 			ctrl3 |= MVPP22_XLG_CTRL3_MACMODESELECT_GMAC;
@@ -4559,7 +4586,7 @@
 		writel(ctrl3, port->base + MVPP22_XLG_CTRL3_REG);
 	}
 
-	if (mvpp2_port_supports_xlg(port) && mvpp2_is_xlg(port->phy_interface))
+	if (mvpp2_port_supports_xlg(port) && mvpp2_is_xlg(interface))
 		mvpp2_xlg_max_rx_size_set(port);
 	else
 		mvpp2_gmac_max_rx_size_set(port);
@@ -4579,7 +4606,7 @@
 	mvpp2_interrupts_enable(port);
 
 	if (port->priv->hw_version >= MVPP22)
-		mvpp22_mode_reconfigure(port);
+		mvpp22_mode_reconfigure(port, port->phy_interface);
 
 	if (port->phylink) {
 		phylink_start(port->phylink);
@@ -5015,11 +5042,13 @@
 		mtu = ALIGN(MVPP2_RX_PKT_SIZE(mtu), 8);
 	}
 
+	if (port->xdp_prog && mtu > MVPP2_MAX_RX_BUF_SIZE) {
+		netdev_err(dev, "Illegal MTU value %d (> %d) for XDP mode\n",
+			   mtu, (int)MVPP2_MAX_RX_BUF_SIZE);
+		return -EINVAL;
+	}
+
 	if (MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE) {
-		if (port->xdp_prog) {
-			netdev_err(dev, "Jumbo frames are not supported with XDP\n");
-			return -EINVAL;
-		}
 		if (priv->percpu_pools) {
 			netdev_warn(dev, "mtu %d too high, switching to shared buffers", mtu);
 			mvpp2_bm_switch_buffers(priv, false);
@@ -5305,8 +5334,8 @@
 	bool running = netif_running(port->dev);
 	bool reset = !prog != !port->xdp_prog;
 
-	if (port->dev->mtu > ETH_DATA_LEN) {
-		NL_SET_ERR_MSG_MOD(bpf->extack, "XDP is not supported with jumbo frames enabled");
+	if (port->dev->mtu > MVPP2_MAX_RX_BUF_SIZE) {
+		NL_SET_ERR_MSG_MOD(bpf->extack, "MTU too large for XDP");
 		return -EOPNOTSUPP;
 	}
 
@@ -5568,6 +5597,11 @@
 		break;
 	case ETHTOOL_GRXCLSRLALL:
 		for (i = 0; i < MVPP2_N_RFS_ENTRIES_PER_FLOW; i++) {
+			if (loc == info->rule_cnt) {
+				ret = -EMSGSIZE;
+				break;
+			}
+
 			if (port->rfs_rules[i])
 				rules[loc++] = i;
 		}
@@ -6083,7 +6117,7 @@
 
 	if (fwnode_get_mac_address(fwnode, fw_mac_addr, ETH_ALEN)) {
 		*mac_from = "firmware node";
-		ether_addr_copy(dev->dev_addr, fw_mac_addr);
+		eth_hw_addr_set(dev, fw_mac_addr);
 		return;
 	}
 
@@ -6091,7 +6125,7 @@
 		mvpp21_get_mac_address(port, hw_mac_addr);
 		if (is_valid_ether_addr(hw_mac_addr)) {
 			*mac_from = "hardware";
-			ether_addr_copy(dev->dev_addr, hw_mac_addr);
+			eth_hw_addr_set(dev, hw_mac_addr);
 			return;
 		}
 	}
@@ -6477,6 +6511,9 @@
 			mvpp22_gop_mask_irq(port);
 
 			phy_power_off(port->comphy);
+
+			/* Reconfigure the serdes lanes */
+			mvpp22_mode_reconfigure(port, interface);
 		}
 	}
 
@@ -6531,9 +6568,6 @@
 	    port->phy_interface != interface) {
 		port->phy_interface = interface;
 
-		/* Reconfigure the serdes lanes */
-		mvpp22_mode_reconfigure(port);
-
 		/* Unmask interrupts */
 		mvpp22_gop_unmask_irq(port);
 	}
@@ -6960,7 +6994,7 @@
 	 * driver does this, we can remove this code.
 	 */
 	if (port->comphy) {
-		err = mvpp22_comphy_init(port);
+		err = mvpp22_comphy_init(port, port->phy_interface);
 		if (err == 0)
 			phy_power_off(port->comphy);
 	}
@@ -7352,6 +7386,7 @@
 			  struct mvpp2 *priv)
 {
 	struct resource *res;
+	void __iomem *base;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
 	if (!res) {
@@ -7362,9 +7397,12 @@
 		return 0;
 	}
 
-	priv->cm3_base = devm_ioremap_resource(&pdev->dev, res);
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
 
-	return PTR_ERR_OR_ZERO(priv->cm3_base);
+	priv->cm3_base = base;
+	return 0;
 }
 
 static int mvpp2_probe(struct platform_device *pdev)
@@ -7453,7 +7491,7 @@
 
 	shared = num_present_cpus() - priv->nthreads;
 	if (shared > 0)
-		bitmap_fill(&priv->lock_map,
+		bitmap_set(&priv->lock_map, 0,
 			    min_t(int, shared, MVPP2_MAX_THREADS));
 
 	for (i = 0; i < MVPP2_MAX_THREADS; i++) {
@@ -7551,8 +7589,9 @@
 	if (mvpp2_read(priv, MVPP2_VER_ID_REG) == MVPP2_VER_PP23)
 		priv->hw_version = MVPP23;
 
-	/* Init mss lock */
+	/* Init locks for shared packet processor resources */
 	spin_lock_init(&priv->mss_spinlock);
+	spin_lock_init(&priv->prs_spinlock);
 
 	/* Initialize network controller */
 	err = mvpp2_init(pdev, priv);
@@ -7706,7 +7745,18 @@
 	},
 };
 
-module_platform_driver(mvpp2_driver);
+static int __init mvpp2_driver_init(void)
+{
+	return platform_driver_register(&mvpp2_driver);
+}
+module_init(mvpp2_driver_init);
+
+static void __exit mvpp2_driver_exit(void)
+{
+	platform_driver_unregister(&mvpp2_driver);
+	mvpp2_dbgfs_exit();
+}
+module_exit(mvpp2_driver_exit);
 
 MODULE_DESCRIPTION("Marvell PPv2 Ethernet Driver - www.marvell.com");
 MODULE_AUTHOR("Marcin Wojtas <mw@semihalf.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c
@@ -23,6 +23,8 @@
 {
 	int i;
 
+	lockdep_assert_held(&priv->prs_spinlock);
+
 	if (pe->index > MVPP2_PRS_TCAM_SRAM_SIZE - 1)
 		return -EINVAL;
 
@@ -43,11 +45,13 @@
 }
 
 /* Initialize tcam entry from hw */
-int mvpp2_prs_init_from_hw(struct mvpp2 *priv, struct mvpp2_prs_entry *pe,
-			   int tid)
+static int __mvpp2_prs_init_from_hw(struct mvpp2 *priv,
+				    struct mvpp2_prs_entry *pe, int tid)
 {
 	int i;
 
+	lockdep_assert_held(&priv->prs_spinlock);
+
 	if (tid > MVPP2_PRS_TCAM_SRAM_SIZE - 1)
 		return -EINVAL;
 
@@ -73,6 +77,18 @@
 	return 0;
 }
 
+int mvpp2_prs_init_from_hw(struct mvpp2 *priv, struct mvpp2_prs_entry *pe,
+			   int tid)
+{
+	int err;
+
+	spin_lock_bh(&priv->prs_spinlock);
+	err = __mvpp2_prs_init_from_hw(priv, pe, tid);
+	spin_unlock_bh(&priv->prs_spinlock);
+
+	return err;
+}
+
 /* Invalidate tcam hw entry */
 static void mvpp2_prs_hw_inv(struct mvpp2 *priv, int index)
 {
@@ -374,7 +390,7 @@
 		    priv->prs_shadow[tid].lu != MVPP2_PRS_LU_FLOWS)
 			continue;
 
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 		bits = mvpp2_prs_sram_ai_get(&pe);
 
 		/* Sram store classification lookup ID in AI bits [5:0] */
@@ -441,7 +457,7 @@
 
 	if (priv->prs_shadow[MVPP2_PE_DROP_ALL].valid) {
 		/* Entry exist - update port only */
-		mvpp2_prs_init_from_hw(priv, &pe, MVPP2_PE_DROP_ALL);
+		__mvpp2_prs_init_from_hw(priv, &pe, MVPP2_PE_DROP_ALL);
 	} else {
 		/* Entry doesn't exist - create new */
 		memset(&pe, 0, sizeof(pe));
@@ -469,14 +485,17 @@
 }
 
 /* Set port to unicast or multicast promiscuous mode */
-void mvpp2_prs_mac_promisc_set(struct mvpp2 *priv, int port,
-			       enum mvpp2_prs_l2_cast l2_cast, bool add)
+static void __mvpp2_prs_mac_promisc_set(struct mvpp2 *priv, int port,
+					enum mvpp2_prs_l2_cast l2_cast,
+					bool add)
 {
 	struct mvpp2_prs_entry pe;
 	unsigned char cast_match;
 	unsigned int ri;
 	int tid;
 
+	lockdep_assert_held(&priv->prs_spinlock);
+
 	if (l2_cast == MVPP2_PRS_L2_UNI_CAST) {
 		cast_match = MVPP2_PRS_UCAST_VAL;
 		tid = MVPP2_PE_MAC_UC_PROMISCUOUS;
@@ -489,7 +508,7 @@
 
 	/* promiscuous mode - Accept unknown unicast or multicast packets */
 	if (priv->prs_shadow[tid].valid) {
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	} else {
 		memset(&pe, 0, sizeof(pe));
 		mvpp2_prs_tcam_lu_set(&pe, MVPP2_PRS_LU_MAC);
@@ -522,6 +541,14 @@
 	mvpp2_prs_hw_write(priv, &pe);
 }
 
+void mvpp2_prs_mac_promisc_set(struct mvpp2 *priv, int port,
+			       enum mvpp2_prs_l2_cast l2_cast, bool add)
+{
+	spin_lock_bh(&priv->prs_spinlock);
+	__mvpp2_prs_mac_promisc_set(priv, port, l2_cast, add);
+	spin_unlock_bh(&priv->prs_spinlock);
+}
+
 /* Set entry for dsa packets */
 static void mvpp2_prs_dsa_tag_set(struct mvpp2 *priv, int port, bool add,
 				  bool tagged, bool extend)
@@ -539,7 +566,7 @@
 
 	if (priv->prs_shadow[tid].valid) {
 		/* Entry exist - update port only */
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	} else {
 		/* Entry doesn't exist - create new */
 		memset(&pe, 0, sizeof(pe));
@@ -610,7 +637,7 @@
 
 	if (priv->prs_shadow[tid].valid) {
 		/* Entry exist - update port only */
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	} else {
 		/* Entry doesn't exist - create new */
 		memset(&pe, 0, sizeof(pe));
@@ -673,7 +700,7 @@
 		    priv->prs_shadow[tid].lu != MVPP2_PRS_LU_VLAN)
 			continue;
 
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 		match = mvpp2_prs_tcam_data_cmp(&pe, 0, tpid);
 		if (!match)
 			continue;
@@ -726,7 +753,7 @@
 			    priv->prs_shadow[tid_aux].lu != MVPP2_PRS_LU_VLAN)
 				continue;
 
-			mvpp2_prs_init_from_hw(priv, &pe, tid_aux);
+			__mvpp2_prs_init_from_hw(priv, &pe, tid_aux);
 			ri_bits = mvpp2_prs_sram_ri_get(&pe);
 			if ((ri_bits & MVPP2_PRS_RI_VLAN_MASK) ==
 			    MVPP2_PRS_RI_VLAN_DOUBLE)
@@ -760,7 +787,7 @@
 
 		mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_VLAN);
 	} else {
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	}
 	/* Update ports' mask */
 	mvpp2_prs_tcam_port_map_set(&pe, port_map);
@@ -800,7 +827,7 @@
 		    priv->prs_shadow[tid].lu != MVPP2_PRS_LU_VLAN)
 			continue;
 
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 
 		match = mvpp2_prs_tcam_data_cmp(&pe, 0, tpid1) &&
 			mvpp2_prs_tcam_data_cmp(&pe, 4, tpid2);
@@ -849,7 +876,7 @@
 			    priv->prs_shadow[tid_aux].lu != MVPP2_PRS_LU_VLAN)
 				continue;
 
-			mvpp2_prs_init_from_hw(priv, &pe, tid_aux);
+			__mvpp2_prs_init_from_hw(priv, &pe, tid_aux);
 			ri_bits = mvpp2_prs_sram_ri_get(&pe);
 			ri_bits &= MVPP2_PRS_RI_VLAN_MASK;
 			if (ri_bits == MVPP2_PRS_RI_VLAN_SINGLE ||
@@ -880,7 +907,7 @@
 
 		mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_VLAN);
 	} else {
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	}
 
 	/* Update ports' mask */
@@ -1213,8 +1240,8 @@
 	/* Create dummy entries for drop all and promiscuous modes */
 	mvpp2_prs_drop_fc(priv);
 	mvpp2_prs_mac_drop_all_set(priv, 0, false);
-	mvpp2_prs_mac_promisc_set(priv, 0, MVPP2_PRS_L2_UNI_CAST, false);
-	mvpp2_prs_mac_promisc_set(priv, 0, MVPP2_PRS_L2_MULTI_CAST, false);
+	__mvpp2_prs_mac_promisc_set(priv, 0, MVPP2_PRS_L2_UNI_CAST, false);
+	__mvpp2_prs_mac_promisc_set(priv, 0, MVPP2_PRS_L2_MULTI_CAST, false);
 }
 
 /* Set default entries for various types of dsa packets */
@@ -1533,14 +1560,8 @@
 	struct mvpp2_prs_entry pe;
 	int err;
 
-	priv->prs_double_vlans = devm_kcalloc(&pdev->dev, sizeof(bool),
-					      MVPP2_PRS_DBL_VLANS_MAX,
-					      GFP_KERNEL);
-	if (!priv->prs_double_vlans)
-		return -ENOMEM;
-
-	/* Double VLAN: 0x8100, 0x88A8 */
-	err = mvpp2_prs_double_vlan_add(priv, ETH_P_8021Q, ETH_P_8021AD,
+	/* Double VLAN: 0x88A8, 0x8100 */
+	err = mvpp2_prs_double_vlan_add(priv, ETH_P_8021AD, ETH_P_8021Q,
 					MVPP2_PRS_PORT_MASK);
 	if (err)
 		return err;
@@ -1607,59 +1628,45 @@
 static int mvpp2_prs_pppoe_init(struct mvpp2 *priv)
 {
 	struct mvpp2_prs_entry pe;
-	int tid;
-
-	/* IPv4 over PPPoE with options */
-	tid = mvpp2_prs_tcam_first_free(priv, MVPP2_PE_FIRST_FREE_TID,
-					MVPP2_PE_LAST_FREE_TID);
-	if (tid < 0)
-		return tid;
-
-	memset(&pe, 0, sizeof(pe));
-	mvpp2_prs_tcam_lu_set(&pe, MVPP2_PRS_LU_PPPOE);
-	pe.index = tid;
-
-	mvpp2_prs_match_etype(&pe, 0, PPP_IP);
-
-	mvpp2_prs_sram_next_lu_set(&pe, MVPP2_PRS_LU_IP4);
-	mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L3_IP4_OPT,
-				 MVPP2_PRS_RI_L3_PROTO_MASK);
-	/* goto ipv4 dest-address (skip eth_type + IP-header-size - 4) */
-	mvpp2_prs_sram_shift_set(&pe, MVPP2_ETH_TYPE_LEN +
-				 sizeof(struct iphdr) - 4,
-				 MVPP2_PRS_SRAM_OP_SEL_SHIFT_ADD);
-	/* Set L3 offset */
-	mvpp2_prs_sram_offset_set(&pe, MVPP2_PRS_SRAM_UDF_TYPE_L3,
-				  MVPP2_ETH_TYPE_LEN,
-				  MVPP2_PRS_SRAM_OP_SEL_UDF_ADD);
-
-	/* Update shadow table and hw entry */
-	mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_PPPOE);
-	mvpp2_prs_hw_write(priv, &pe);
+	int tid, ihl;
 
-	/* IPv4 over PPPoE without options */
-	tid = mvpp2_prs_tcam_first_free(priv, MVPP2_PE_FIRST_FREE_TID,
-					MVPP2_PE_LAST_FREE_TID);
-	if (tid < 0)
-		return tid;
+	/* IPv4 over PPPoE with header length >= 5 */
+	for (ihl = MVPP2_PRS_IPV4_IHL_MIN; ihl <= MVPP2_PRS_IPV4_IHL_MAX; ihl++) {
+		tid = mvpp2_prs_tcam_first_free(priv, MVPP2_PE_FIRST_FREE_TID,
+						MVPP2_PE_LAST_FREE_TID);
+		if (tid < 0)
+			return tid;
 
-	pe.index = tid;
+		memset(&pe, 0, sizeof(pe));
+		mvpp2_prs_tcam_lu_set(&pe, MVPP2_PRS_LU_PPPOE);
+		pe.index = tid;
 
-	mvpp2_prs_tcam_data_byte_set(&pe, MVPP2_ETH_TYPE_LEN,
-				     MVPP2_PRS_IPV4_HEAD |
-				     MVPP2_PRS_IPV4_IHL_MIN,
-				     MVPP2_PRS_IPV4_HEAD_MASK |
-				     MVPP2_PRS_IPV4_IHL_MASK);
+		mvpp2_prs_match_etype(&pe, 0, PPP_IP);
+		mvpp2_prs_tcam_data_byte_set(&pe, MVPP2_ETH_TYPE_LEN,
+					     MVPP2_PRS_IPV4_HEAD | ihl,
+					     MVPP2_PRS_IPV4_HEAD_MASK |
+					     MVPP2_PRS_IPV4_IHL_MASK);
 
-	/* Clear ri before updating */
-	pe.sram[MVPP2_PRS_SRAM_RI_WORD] = 0x0;
-	pe.sram[MVPP2_PRS_SRAM_RI_CTRL_WORD] = 0x0;
-	mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L3_IP4,
-				 MVPP2_PRS_RI_L3_PROTO_MASK);
+		mvpp2_prs_sram_next_lu_set(&pe, MVPP2_PRS_LU_IP4);
+		mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L3_IP4,
+					 MVPP2_PRS_RI_L3_PROTO_MASK);
+		/* goto ipv4 dst-address (skip eth_type + IP-header-size - 4) */
+		mvpp2_prs_sram_shift_set(&pe, MVPP2_ETH_TYPE_LEN +
+					 sizeof(struct iphdr) - 4,
+					 MVPP2_PRS_SRAM_OP_SEL_SHIFT_ADD);
+		/* Set L3 offset */
+		mvpp2_prs_sram_offset_set(&pe, MVPP2_PRS_SRAM_UDF_TYPE_L3,
+					  MVPP2_ETH_TYPE_LEN,
+					  MVPP2_PRS_SRAM_OP_SEL_UDF_ADD);
+		/* Set L4 offset */
+		mvpp2_prs_sram_offset_set(&pe, MVPP2_PRS_SRAM_UDF_TYPE_L4,
+					  MVPP2_ETH_TYPE_LEN + (ihl * 4),
+					  MVPP2_PRS_SRAM_OP_SEL_UDF_ADD);
 
-	/* Update shadow table and hw entry */
-	mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_PPPOE);
-	mvpp2_prs_hw_write(priv, &pe);
+		/* Update shadow table and hw entry */
+		mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_PPPOE);
+		mvpp2_prs_hw_write(priv, &pe);
+	}
 
 	/* IPv6 over PPPoE */
 	tid = mvpp2_prs_tcam_first_free(priv, MVPP2_PE_FIRST_FREE_TID,
@@ -1955,7 +1962,7 @@
 		    port->priv->prs_shadow[tid].lu != MVPP2_PRS_LU_VID)
 			continue;
 
-		mvpp2_prs_init_from_hw(port->priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(port->priv, &pe, tid);
 
 		mvpp2_prs_tcam_data_byte_get(&pe, 2, &byte[0], &enable[0]);
 		mvpp2_prs_tcam_data_byte_get(&pe, 3, &byte[1], &enable[1]);
@@ -1984,6 +1991,8 @@
 
 	memset(&pe, 0, sizeof(pe));
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	/* Scan TCAM and see if entry with this <vid,port> already exist */
 	tid = mvpp2_prs_vid_range_find(port, vid, mask);
 
@@ -2002,8 +2011,10 @@
 						MVPP2_PRS_VLAN_FILT_MAX_ENTRY);
 
 		/* There isn't room for a new VID filter */
-		if (tid < 0)
+		if (tid < 0) {
+			spin_unlock_bh(&priv->prs_spinlock);
 			return tid;
+		}
 
 		mvpp2_prs_tcam_lu_set(&pe, MVPP2_PRS_LU_VID);
 		pe.index = tid;
@@ -2011,7 +2022,7 @@
 		/* Mask all ports */
 		mvpp2_prs_tcam_port_map_set(&pe, 0);
 	} else {
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	}
 
 	/* Enable the current port */
@@ -2033,6 +2044,7 @@
 	mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_VID);
 	mvpp2_prs_hw_write(priv, &pe);
 
+	spin_unlock_bh(&priv->prs_spinlock);
 	return 0;
 }
 
@@ -2042,15 +2054,16 @@
 	struct mvpp2 *priv = port->priv;
 	int tid;
 
-	/* Scan TCAM and see if entry with this <vid,port> already exist */
-	tid = mvpp2_prs_vid_range_find(port, vid, 0xfff);
+	spin_lock_bh(&priv->prs_spinlock);
 
-	/* No such entry */
-	if (tid < 0)
-		return;
+	/* Invalidate TCAM entry with this <vid,port>, if it exists */
+	tid = mvpp2_prs_vid_range_find(port, vid, 0xfff);
+	if (tid >= 0) {
+		mvpp2_prs_hw_inv(priv, tid);
+		priv->prs_shadow[tid].valid = false;
+	}
 
-	mvpp2_prs_hw_inv(priv, tid);
-	priv->prs_shadow[tid].valid = false;
+	spin_unlock_bh(&priv->prs_spinlock);
 }
 
 /* Remove all existing VID filters on this port */
@@ -2059,6 +2072,8 @@
 	struct mvpp2 *priv = port->priv;
 	int tid;
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	for (tid = MVPP2_PRS_VID_PORT_FIRST(port->id);
 	     tid <= MVPP2_PRS_VID_PORT_LAST(port->id); tid++) {
 		if (priv->prs_shadow[tid].valid) {
@@ -2066,6 +2081,8 @@
 			priv->prs_shadow[tid].valid = false;
 		}
 	}
+
+	spin_unlock_bh(&priv->prs_spinlock);
 }
 
 /* Remove VID filering entry for this port */
@@ -2074,10 +2091,14 @@
 	unsigned int tid = MVPP2_PRS_VID_PORT_DFLT(port->id);
 	struct mvpp2 *priv = port->priv;
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	/* Invalidate the guard entry */
 	mvpp2_prs_hw_inv(priv, tid);
 
 	priv->prs_shadow[tid].valid = false;
+
+	spin_unlock_bh(&priv->prs_spinlock);
 }
 
 /* Add guard entry that drops packets when no VID is matched on this port */
@@ -2093,6 +2114,8 @@
 
 	memset(&pe, 0, sizeof(pe));
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	pe.index = tid;
 
 	reg_val = mvpp2_read(priv, MVPP2_MH_REG(port->id));
@@ -2125,6 +2148,8 @@
 	/* Update shadow table */
 	mvpp2_prs_shadow_set(priv, pe.index, MVPP2_PRS_LU_VID);
 	mvpp2_prs_hw_write(priv, &pe);
+
+	spin_unlock_bh(&priv->prs_spinlock);
 }
 
 /* Parser default initialization */
@@ -2132,6 +2157,20 @@
 {
 	int err, index, i;
 
+	priv->prs_shadow = devm_kcalloc(&pdev->dev, MVPP2_PRS_TCAM_SRAM_SIZE,
+					sizeof(*priv->prs_shadow),
+					GFP_KERNEL);
+	if (!priv->prs_shadow)
+		return -ENOMEM;
+
+	priv->prs_double_vlans = devm_kcalloc(&pdev->dev, sizeof(bool),
+					      MVPP2_PRS_DBL_VLANS_MAX,
+					      GFP_KERNEL);
+	if (!priv->prs_double_vlans)
+		return -ENOMEM;
+
+	spin_lock_bh(&priv->prs_spinlock);
+
 	/* Enable tcam table */
 	mvpp2_write(priv, MVPP2_PRS_TCAM_CTRL_REG, MVPP2_PRS_TCAM_EN_MASK);
 
@@ -2150,12 +2189,6 @@
 	for (index = 0; index < MVPP2_PRS_TCAM_SRAM_SIZE; index++)
 		mvpp2_prs_hw_inv(priv, index);
 
-	priv->prs_shadow = devm_kcalloc(&pdev->dev, MVPP2_PRS_TCAM_SRAM_SIZE,
-					sizeof(*priv->prs_shadow),
-					GFP_KERNEL);
-	if (!priv->prs_shadow)
-		return -ENOMEM;
-
 	/* Always start from lookup = 0 */
 	for (index = 0; index < MVPP2_MAX_PORTS; index++)
 		mvpp2_prs_hw_port_init(priv, index, MVPP2_PRS_LU_MH,
@@ -2172,26 +2205,13 @@
 	mvpp2_prs_vid_init(priv);
 
 	err = mvpp2_prs_etype_init(priv);
-	if (err)
-		return err;
-
-	err = mvpp2_prs_vlan_init(pdev, priv);
-	if (err)
-		return err;
-
-	err = mvpp2_prs_pppoe_init(priv);
-	if (err)
-		return err;
-
-	err = mvpp2_prs_ip6_init(priv);
-	if (err)
-		return err;
-
-	err = mvpp2_prs_ip4_init(priv);
-	if (err)
-		return err;
+	err = err ? : mvpp2_prs_vlan_init(pdev, priv);
+	err = err ? : mvpp2_prs_pppoe_init(priv);
+	err = err ? : mvpp2_prs_ip6_init(priv);
+	err = err ? : mvpp2_prs_ip4_init(priv);
 
-	return 0;
+	spin_unlock_bh(&priv->prs_spinlock);
+	return err;
 }
 
 /* Compare MAC DA with tcam entry data */
@@ -2231,7 +2251,7 @@
 		    (priv->prs_shadow[tid].udf != udf_type))
 			continue;
 
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 		entry_pmap = mvpp2_prs_tcam_port_map_get(&pe);
 
 		if (mvpp2_prs_mac_range_equals(&pe, da, mask) &&
@@ -2243,7 +2263,8 @@
 }
 
 /* Update parser's mac da entry */
-int mvpp2_prs_mac_da_accept(struct mvpp2_port *port, const u8 *da, bool add)
+static int __mvpp2_prs_mac_da_accept(struct mvpp2_port *port,
+				     const u8 *da, bool add)
 {
 	unsigned char mask[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
 	struct mvpp2 *priv = port->priv;
@@ -2275,7 +2296,7 @@
 		/* Mask all ports */
 		mvpp2_prs_tcam_port_map_set(&pe, 0);
 	} else {
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 	}
 
 	mvpp2_prs_tcam_lu_set(&pe, MVPP2_PRS_LU_MAC);
@@ -2331,6 +2352,17 @@
 	return 0;
 }
 
+int mvpp2_prs_mac_da_accept(struct mvpp2_port *port, const u8 *da, bool add)
+{
+	int err;
+
+	spin_lock_bh(&port->priv->prs_spinlock);
+	err = __mvpp2_prs_mac_da_accept(port, da, add);
+	spin_unlock_bh(&port->priv->prs_spinlock);
+
+	return err;
+}
+
 int mvpp2_prs_update_mac_da(struct net_device *dev, const u8 *da)
 {
 	struct mvpp2_port *port = netdev_priv(dev);
@@ -2347,7 +2379,7 @@
 		return err;
 
 	/* Set addr in the device */
-	ether_addr_copy(dev->dev_addr, da);
+	eth_hw_addr_set(dev, da);
 
 	return 0;
 }
@@ -2359,6 +2391,8 @@
 	unsigned long pmap;
 	int index, tid;
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	for (tid = MVPP2_PE_MAC_RANGE_START;
 	     tid <= MVPP2_PE_MAC_RANGE_END; tid++) {
 		unsigned char da[ETH_ALEN], da_mask[ETH_ALEN];
@@ -2368,7 +2402,7 @@
 		    (priv->prs_shadow[tid].udf != MVPP2_PRS_UDF_MAC_DEF))
 			continue;
 
-		mvpp2_prs_init_from_hw(priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(priv, &pe, tid);
 
 		pmap = mvpp2_prs_tcam_port_map_get(&pe);
 
@@ -2389,14 +2423,17 @@
 			continue;
 
 		/* Remove entry from TCAM */
-		mvpp2_prs_mac_da_accept(port, da, false);
+		__mvpp2_prs_mac_da_accept(port, da, false);
 	}
+
+	spin_unlock_bh(&priv->prs_spinlock);
 }
 
 int mvpp2_prs_tag_mode_set(struct mvpp2 *priv, int port, int type)
 {
 	switch (type) {
 	case MVPP2_TAG_TYPE_EDSA:
+		spin_lock_bh(&priv->prs_spinlock);
 		/* Add port to EDSA entries */
 		mvpp2_prs_dsa_tag_set(priv, port, true,
 				      MVPP2_PRS_TAGGED, MVPP2_PRS_EDSA);
@@ -2407,9 +2444,11 @@
 				      MVPP2_PRS_TAGGED, MVPP2_PRS_DSA);
 		mvpp2_prs_dsa_tag_set(priv, port, false,
 				      MVPP2_PRS_UNTAGGED, MVPP2_PRS_DSA);
+		spin_unlock_bh(&priv->prs_spinlock);
 		break;
 
 	case MVPP2_TAG_TYPE_DSA:
+		spin_lock_bh(&priv->prs_spinlock);
 		/* Add port to DSA entries */
 		mvpp2_prs_dsa_tag_set(priv, port, true,
 				      MVPP2_PRS_TAGGED, MVPP2_PRS_DSA);
@@ -2420,10 +2459,12 @@
 				      MVPP2_PRS_TAGGED, MVPP2_PRS_EDSA);
 		mvpp2_prs_dsa_tag_set(priv, port, false,
 				      MVPP2_PRS_UNTAGGED, MVPP2_PRS_EDSA);
+		spin_unlock_bh(&priv->prs_spinlock);
 		break;
 
 	case MVPP2_TAG_TYPE_MH:
 	case MVPP2_TAG_TYPE_NONE:
+		spin_lock_bh(&priv->prs_spinlock);
 		/* Remove port form EDSA and DSA entries */
 		mvpp2_prs_dsa_tag_set(priv, port, false,
 				      MVPP2_PRS_TAGGED, MVPP2_PRS_DSA);
@@ -2433,6 +2474,7 @@
 				      MVPP2_PRS_TAGGED, MVPP2_PRS_EDSA);
 		mvpp2_prs_dsa_tag_set(priv, port, false,
 				      MVPP2_PRS_UNTAGGED, MVPP2_PRS_EDSA);
+		spin_unlock_bh(&priv->prs_spinlock);
 		break;
 
 	default:
@@ -2451,11 +2493,15 @@
 
 	memset(&pe, 0, sizeof(pe));
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	tid = mvpp2_prs_tcam_first_free(priv,
 					MVPP2_PE_LAST_FREE_TID,
 					MVPP2_PE_FIRST_FREE_TID);
-	if (tid < 0)
+	if (tid < 0) {
+		spin_unlock_bh(&priv->prs_spinlock);
 		return tid;
+	}
 
 	pe.index = tid;
 
@@ -2475,6 +2521,7 @@
 	mvpp2_prs_tcam_port_map_set(&pe, MVPP2_PRS_PORT_MASK);
 	mvpp2_prs_hw_write(priv, &pe);
 
+	spin_unlock_bh(&priv->prs_spinlock);
 	return 0;
 }
 
@@ -2486,6 +2533,8 @@
 
 	memset(&pe, 0, sizeof(pe));
 
+	spin_lock_bh(&port->priv->prs_spinlock);
+
 	tid = mvpp2_prs_flow_find(port->priv, port->id);
 
 	/* Such entry not exist */
@@ -2494,8 +2543,10 @@
 		tid = mvpp2_prs_tcam_first_free(port->priv,
 						MVPP2_PE_LAST_FREE_TID,
 					       MVPP2_PE_FIRST_FREE_TID);
-		if (tid < 0)
+		if (tid < 0) {
+			spin_unlock_bh(&port->priv->prs_spinlock);
 			return tid;
+		}
 
 		pe.index = tid;
 
@@ -2506,13 +2557,14 @@
 		/* Update shadow table */
 		mvpp2_prs_shadow_set(port->priv, pe.index, MVPP2_PRS_LU_FLOWS);
 	} else {
-		mvpp2_prs_init_from_hw(port->priv, &pe, tid);
+		__mvpp2_prs_init_from_hw(port->priv, &pe, tid);
 	}
 
 	mvpp2_prs_tcam_lu_set(&pe, MVPP2_PRS_LU_FLOWS);
 	mvpp2_prs_tcam_port_map_set(&pe, (1 << port->id));
 	mvpp2_prs_hw_write(port->priv, &pe);
 
+	spin_unlock_bh(&port->priv->prs_spinlock);
 	return 0;
 }
 
@@ -2523,11 +2575,14 @@
 	if (index > MVPP2_PRS_TCAM_SRAM_SIZE)
 		return -EINVAL;
 
+	spin_lock_bh(&priv->prs_spinlock);
+
 	mvpp2_write(priv, MVPP2_PRS_TCAM_HIT_IDX_REG, index);
 
 	val = mvpp2_read(priv, MVPP2_PRS_TCAM_HIT_CNT_REG);
 
 	val &= MVPP2_PRS_TCAM_HIT_CNT_MASK;
 
+	spin_unlock_bh(&priv->prs_spinlock);
 	return val;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/Kconfig
@@ -31,6 +31,7 @@
 config OCTEONTX2_PF
 	tristate "Marvell OcteonTX2 NIC Physical Function driver"
 	select OCTEONTX2_MBOX
+	select NET_DEVLINK
 	depends on (64BIT && COMPILE_TEST) || ARM64
 	depends on PCI
 	depends on PTP_1588_CLOCK_OPTIONAL
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/cgx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/cgx.c
@@ -167,6 +167,9 @@
 {
 	struct cgx *cgx_dev = cgx_get_pdata(cgx_id);
 
+	/* Software must not access disabled LMAC registers */
+	if (!is_lmac_valid(cgx_dev, lmac_id))
+		return;
 	cgx_write(cgx_dev, lmac_id, offset, val);
 }
 
@@ -174,6 +177,10 @@
 {
 	struct cgx *cgx_dev = cgx_get_pdata(cgx_id);
 
+	/* Software must not access disabled LMAC registers */
+	if (!is_lmac_valid(cgx_dev, lmac_id))
+		return 0;
+
 	return cgx_read(cgx_dev, lmac_id, offset);
 }
 
@@ -498,6 +505,32 @@
 	return (cfg >> CGX_LMAC_TYPE_SHIFT) & CGX_LMAC_TYPE_MASK;
 }
 
+static u32 cgx_get_lmac_fifo_len(void *cgxd, int lmac_id)
+{
+	struct cgx *cgx = cgxd;
+	u8 num_lmacs;
+	u32 fifo_len;
+
+	fifo_len = cgx->mac_ops->fifo_len;
+	num_lmacs = cgx->mac_ops->get_nr_lmacs(cgx);
+
+	switch (num_lmacs) {
+	case 1:
+		return fifo_len;
+	case 2:
+		return fifo_len / 2;
+	case 3:
+		/* LMAC0 gets half of the FIFO, reset 1/4th */
+		if (lmac_id == 0)
+			return fifo_len / 2;
+		return fifo_len / 4;
+	case 4:
+	default:
+		return fifo_len / 4;
+	}
+	return 0;
+}
+
 /* Configure CGX LMAC in internal loopback mode */
 int cgx_lmac_internal_loopback(void *cgxd, int lmac_id, bool enable)
 {
@@ -695,9 +728,9 @@
 
 	cfg = cgx_read(cgx, lmac_id, CGXX_CMRX_CFG);
 	if (enable)
-		cfg |= CMR_EN | DATA_PKT_RX_EN | DATA_PKT_TX_EN;
+		cfg |= DATA_PKT_RX_EN | DATA_PKT_TX_EN;
 	else
-		cfg &= ~(CMR_EN | DATA_PKT_RX_EN | DATA_PKT_TX_EN);
+		cfg &= ~(DATA_PKT_RX_EN | DATA_PKT_TX_EN);
 	cgx_write(cgx, lmac_id, CGXX_CMRX_CFG, cfg);
 	return 0;
 }
@@ -754,6 +787,11 @@
 	if (!is_lmac_valid(cgx, lmac_id))
 		return -ENODEV;
 
+	cfg = cgx_read(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL);
+	cfg &= ~CGX_GMP_GMI_RXX_FRM_CTL_CTL_BCK;
+	cfg |= rx_pause ? CGX_GMP_GMI_RXX_FRM_CTL_CTL_BCK : 0x0;
+	cgx_write(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL, cfg);
+
 	cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL);
 	cfg &= ~CGX_SMUX_RX_FRM_CTL_CTL_BCK;
 	cfg |= rx_pause ? CGX_SMUX_RX_FRM_CTL_CTL_BCK : 0x0;
@@ -782,21 +820,8 @@
 
 	if (!is_lmac_valid(cgx, lmac_id))
 		return;
-	if (enable) {
-		/* Enable receive pause frames */
-		cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL);
-		cfg |= CGX_SMUX_RX_FRM_CTL_CTL_BCK;
-		cgx_write(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL, cfg);
-
-		cfg = cgx_read(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL);
-		cfg |= CGX_GMP_GMI_RXX_FRM_CTL_CTL_BCK;
-		cgx_write(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL, cfg);
-
-		/* Enable pause frames transmission */
-		cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_TX_CTL);
-		cfg |= CGX_SMUX_TX_CTL_L2P_BP_CONV;
-		cgx_write(cgx, lmac_id, CGXX_SMUX_TX_CTL, cfg);
 
+	if (enable) {
 		/* Set pause time and interval */
 		cgx_write(cgx, lmac_id, CGXX_SMUX_TX_PAUSE_PKT_TIME,
 			  DEFAULT_PAUSE_TIME);
@@ -813,21 +838,21 @@
 		cfg &= ~0xFFFFULL;
 		cgx_write(cgx, lmac_id, CGXX_GMP_GMI_TX_PAUSE_PKT_INTERVAL,
 			  cfg | (DEFAULT_PAUSE_TIME / 2));
-	} else {
-		/* ALL pause frames received are completely ignored */
-		cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL);
-		cfg &= ~CGX_SMUX_RX_FRM_CTL_CTL_BCK;
-		cgx_write(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL, cfg);
+	}
 
-		cfg = cgx_read(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL);
-		cfg &= ~CGX_GMP_GMI_RXX_FRM_CTL_CTL_BCK;
-		cgx_write(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL, cfg);
+	/* ALL pause frames received are completely ignored */
+	cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL);
+	cfg &= ~CGX_SMUX_RX_FRM_CTL_CTL_BCK;
+	cgx_write(cgx, lmac_id, CGXX_SMUX_RX_FRM_CTL, cfg);
 
-		/* Disable pause frames transmission */
-		cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_TX_CTL);
-		cfg &= ~CGX_SMUX_TX_CTL_L2P_BP_CONV;
-		cgx_write(cgx, lmac_id, CGXX_SMUX_TX_CTL, cfg);
-	}
+	cfg = cgx_read(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL);
+	cfg &= ~CGX_GMP_GMI_RXX_FRM_CTL_CTL_BCK;
+	cgx_write(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL, cfg);
+
+	/* Disable pause frames transmission */
+	cfg = cgx_read(cgx, lmac_id, CGXX_SMUX_TX_CTL);
+	cfg &= ~CGX_SMUX_TX_CTL_L2P_BP_CONV;
+	cgx_write(cgx, lmac_id, CGXX_SMUX_TX_CTL, cfg);
 }
 
 void cgx_lmac_ptp_config(void *cgxd, int lmac_id, bool enable)
@@ -838,9 +863,6 @@
 	if (!cgx)
 		return;
 
-	if (is_dev_rpm(cgx))
-		return;
-
 	if (enable) {
 		/* Enable inbound PTP timestamping */
 		cfg = cgx_read(cgx, lmac_id, CGXX_GMP_GMI_RXX_FRM_CTL);
@@ -1188,7 +1210,7 @@
 
 		/* Release thread waiting for completion  */
 		lmac->cmd_pend = false;
-		wake_up_interruptible(&lmac->wq_cmd_cmplt);
+		wake_up(&lmac->wq_cmd_cmplt);
 		break;
 	case CGX_EVT_ASYNC:
 		if (cgx_event_is_linkevent(event))
@@ -1545,9 +1567,11 @@
 static void cgx_populate_features(struct cgx *cgx)
 {
 	if (is_dev_rpm(cgx))
-		cgx->hw_features =  (RVU_MAC_RPM | RVU_LMAC_FEAT_FC);
+		cgx->hw_features = (RVU_LMAC_FEAT_DMACF | RVU_MAC_RPM |
+				    RVU_LMAC_FEAT_FC | RVU_LMAC_FEAT_PTP);
 	else
-		cgx->hw_features = (RVU_LMAC_FEAT_FC | RVU_LMAC_FEAT_PTP);
+		cgx->hw_features = (RVU_LMAC_FEAT_FC  | RVU_LMAC_FEAT_HIGIG2 |
+				    RVU_LMAC_FEAT_PTP | RVU_LMAC_FEAT_DMACF);
 }
 
 static struct mac_ops	cgx_mac_ops    = {
@@ -1564,6 +1588,7 @@
 	.tx_stats_cnt   =       18,
 	.get_nr_lmacs	=	cgx_get_nr_lmacs,
 	.get_lmac_type  =       cgx_get_lmac_type,
+	.lmac_fifo_len	=	cgx_get_lmac_fifo_len,
 	.mac_lmac_intl_lbk =    cgx_lmac_internal_loopback,
 	.mac_get_rx_stats  =	cgx_get_rx_stats,
 	.mac_get_tx_stats  =	cgx_get_tx_stats,
@@ -1571,6 +1596,9 @@
 	.mac_get_pause_frm_status =	cgx_lmac_get_pause_frm_status,
 	.mac_enadis_pause_frm =		cgx_lmac_enadis_pause_frm,
 	.mac_pause_frm_config =		cgx_lmac_pause_frm_config,
+	.mac_enadis_ptp_config =	cgx_lmac_ptp_config,
+	.mac_rx_tx_enable =		cgx_lmac_rx_tx_enable,
+	.mac_tx_enable =		cgx_lmac_tx_enable,
 };
 
 static int cgx_probe(struct pci_dev *pdev, const struct pci_device_id *id)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/cgx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/cgx.h
@@ -30,7 +30,6 @@
 #define CMR_P2X_SEL_SHIFT		59ULL
 #define CMR_P2X_SEL_NIX0		1ULL
 #define CMR_P2X_SEL_NIX1		2ULL
-#define CMR_EN				BIT_ULL(55)
 #define DATA_PKT_TX_EN			BIT_ULL(53)
 #define DATA_PKT_RX_EN			BIT_ULL(54)
 #define CGX_LMAC_TYPE_SHIFT		40
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/lmac_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/lmac_common.h
@@ -76,6 +76,7 @@
 	 */
 	int			(*get_nr_lmacs)(void *cgx);
 	u8                      (*get_lmac_type)(void *cgx, int lmac_id);
+	u32                     (*lmac_fifo_len)(void *cgx, int lmac_id);
 	int                     (*mac_lmac_intl_lbk)(void *cgx, int lmac_id,
 						     bool enable);
 	/* Register Stats related functions */
@@ -102,6 +103,14 @@
 	void			(*mac_pause_frm_config)(void  *cgxd,
 							int lmac_id,
 							bool enable);
+
+	/* Enable/Disable Inbound PTP */
+	void			(*mac_enadis_ptp_config)(void  *cgxd,
+							 int lmac_id,
+							 bool enable);
+
+	int			(*mac_rx_tx_enable)(void *cgxd, int lmac_id, bool enable);
+	int			(*mac_tx_enable)(void *cgxd, int lmac_id, bool enable);
 };
 
 struct cgx {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/mbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/mbox.c
@@ -157,7 +157,7 @@
  */
 int otx2_mbox_regions_init(struct otx2_mbox *mbox, void **hwbase,
 			   struct pci_dev *pdev, void *reg_base,
-			   int direction, int ndevs)
+			   int direction, int ndevs, unsigned long *pf_bmap)
 {
 	struct otx2_mbox_dev *mdev;
 	int devid, err;
@@ -169,6 +169,9 @@
 	mbox->hwbase = hwbase[0];
 
 	for (devid = 0; devid < ndevs; devid++) {
+		if (!test_bit(devid, pf_bmap))
+			continue;
+
 		mdev = &mbox->dev[devid];
 		mdev->mbase = hwbase[devid];
 		mdev->hwbase = hwbase[devid];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/mbox.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/mbox.h
@@ -84,7 +84,7 @@
 #define OTX2_MBOX_REQ_SIG (0xdead)
 #define OTX2_MBOX_RSP_SIG (0xbeef)
 	u16 sig;         /* Signature, for validating corrupted msgs */
-#define OTX2_MBOX_VERSION (0x0009)
+#define OTX2_MBOX_VERSION (0x000a)
 	u16 ver;         /* Version of msg's structure for this ID */
 	u16 next_msgoff; /* Offset of next msg within mailbox region */
 	int rc;          /* Msg process'ed response code */
@@ -96,9 +96,10 @@
 int otx2_mbox_init(struct otx2_mbox *mbox, void __force *hwbase,
 		   struct pci_dev *pdev, void __force *reg_base,
 		   int direction, int ndevs);
+
 int otx2_mbox_regions_init(struct otx2_mbox *mbox, void __force **hwbase,
 			   struct pci_dev *pdev, void __force *reg_base,
-			   int direction, int ndevs);
+			   int direction, int ndevs, unsigned long *bmap);
 void otx2_mbox_msg_send(struct otx2_mbox *mbox, int devid);
 int otx2_mbox_wait_for_rsp(struct otx2_mbox *mbox, int devid);
 int otx2_mbox_busy_poll_for_rsp(struct otx2_mbox *mbox, int devid);
@@ -154,23 +155,23 @@
 M(CGX_PTP_RX_DISABLE,	0x20D, cgx_ptp_rx_disable, msg_req, msg_rsp)	\
 M(CGX_CFG_PAUSE_FRM,	0x20E, cgx_cfg_pause_frm, cgx_pause_frm_cfg,	\
 			       cgx_pause_frm_cfg)			\
-M(CGX_FEC_SET,		0x210, cgx_set_fec_param, fec_mode, fec_mode)   \
-M(CGX_FEC_STATS,	0x211, cgx_fec_stats, msg_req, cgx_fec_stats_rsp) \
-M(CGX_GET_PHY_FEC_STATS, 0x212, cgx_get_phy_fec_stats, msg_req, msg_rsp) \
-M(CGX_FW_DATA_GET,	0x213, cgx_get_aux_link_info, msg_req, cgx_fw_data) \
-M(CGX_SET_LINK_MODE,	0x214, cgx_set_link_mode, cgx_set_link_mode_req,\
-			       cgx_set_link_mode_rsp)	\
-M(CGX_FEATURES_GET,	0x215, cgx_features_get, msg_req,		\
-			       cgx_features_info_msg)			\
-M(RPM_STATS,		0x216, rpm_stats, msg_req, rpm_stats_rsp)	\
-M(CGX_MAC_ADDR_ADD,	0x217, cgx_mac_addr_add, cgx_mac_addr_add_req,    \
-			       cgx_mac_addr_add_rsp)		\
-M(CGX_MAC_ADDR_DEL,	0x218, cgx_mac_addr_del, cgx_mac_addr_del_req,    \
+M(CGX_FW_DATA_GET,	0x20F, cgx_get_aux_link_info, msg_req, cgx_fw_data) \
+M(CGX_FEC_SET,		0x210, cgx_set_fec_param, fec_mode, fec_mode) \
+M(CGX_MAC_ADDR_ADD,	0x211, cgx_mac_addr_add, cgx_mac_addr_add_req,    \
+				cgx_mac_addr_add_rsp)		\
+M(CGX_MAC_ADDR_DEL,	0x212, cgx_mac_addr_del, cgx_mac_addr_del_req,    \
 			       msg_rsp)		\
-M(CGX_MAC_MAX_ENTRIES_GET, 0x219, cgx_mac_max_entries_get, msg_req,    \
+M(CGX_MAC_MAX_ENTRIES_GET, 0x213, cgx_mac_max_entries_get, msg_req,    \
 				  cgx_max_dmac_entries_get_rsp)		\
-M(CGX_MAC_ADDR_RESET,	0x21A, cgx_mac_addr_reset, msg_req, msg_rsp)	\
-M(CGX_MAC_ADDR_UPDATE,	0x21B, cgx_mac_addr_update, cgx_mac_addr_update_req, \
+M(CGX_FEC_STATS,	0x217, cgx_fec_stats, msg_req, cgx_fec_stats_rsp) \
+M(CGX_SET_LINK_MODE,	0x218, cgx_set_link_mode, cgx_set_link_mode_req,\
+			       cgx_set_link_mode_rsp)	\
+M(CGX_GET_PHY_FEC_STATS, 0x219, cgx_get_phy_fec_stats, msg_req, msg_rsp) \
+M(CGX_FEATURES_GET,	0x21B, cgx_features_get, msg_req,		\
+			       cgx_features_info_msg)			\
+M(RPM_STATS,		0x21C, rpm_stats, msg_req, rpm_stats_rsp)	\
+M(CGX_MAC_ADDR_RESET,	0x21D, cgx_mac_addr_reset, msg_req, msg_rsp)	\
+M(CGX_MAC_ADDR_UPDATE,	0x21E, cgx_mac_addr_update, cgx_mac_addr_update_req, \
 			       msg_rsp)					\
 /* NPA mbox IDs (range 0x400 - 0x5FF) */				\
 M(NPA_LF_ALLOC,		0x400, npa_lf_alloc,				\
@@ -229,6 +230,8 @@
 M(NPC_MCAM_READ_ENTRY,	  0x600f, npc_mcam_read_entry,			\
 				  npc_mcam_read_entry_req,		\
 				  npc_mcam_read_entry_rsp)		\
+M(NPC_SET_PKIND,        0x6010,   npc_set_pkind,                        \
+				  npc_set_pkind, msg_rsp)               \
 M(NPC_MCAM_READ_BASE_RULE, 0x6011, npc_read_base_steer_rule,            \
 				   msg_req, npc_mcam_read_base_rule_rsp)  \
 M(NPC_MCAM_GET_STATS, 0x6012, npc_mcam_entry_stats,                     \
@@ -575,10 +578,13 @@
 };
 
 #define RVU_LMAC_FEAT_FC		BIT_ULL(0) /* pause frames */
-#define RVU_LMAC_FEAT_PTP		BIT_ULL(1) /* precision time protocol */
-#define RVU_MAC_VERSION			BIT_ULL(2)
-#define RVU_MAC_CGX			BIT_ULL(3)
-#define RVU_MAC_RPM			BIT_ULL(4)
+#define	RVU_LMAC_FEAT_HIGIG2		BIT_ULL(1)
+			/* flow control from physical link higig2 messages */
+#define RVU_LMAC_FEAT_PTP		BIT_ULL(2) /* precison time protocol */
+#define RVU_LMAC_FEAT_DMACF		BIT_ULL(3) /* DMAC FILTER */
+#define RVU_MAC_VERSION			BIT_ULL(4)
+#define RVU_MAC_CGX			BIT_ULL(5)
+#define RVU_MAC_RPM			BIT_ULL(6)
 
 struct cgx_features_info_msg {
 	struct mbox_msghdr hdr;
@@ -593,6 +599,22 @@
 	u64 tx_stats[RPM_TX_STATS_COUNT];
 };
 
+struct npc_set_pkind {
+	struct mbox_msghdr hdr;
+#define OTX2_PRIV_FLAGS_DEFAULT  BIT_ULL(0)
+#define OTX2_PRIV_FLAGS_CUSTOM   BIT_ULL(63)
+	u64 mode;
+#define PKIND_TX		BIT_ULL(0)
+#define PKIND_RX		BIT_ULL(1)
+	u8 dir;
+	u8 pkind; /* valid only in case custom flag */
+	u8 var_len_off; /* Offset of custom header length field.
+			 * Valid only for pkind NPC_RX_CUSTOM_PRE_L2_PKIND
+			 */
+	u8 var_len_off_mask; /* Mask for length with in offset */
+	u8 shift_dir; /* shift direction to get length of the header at var_len_off */
+};
+
 /* NPA mbox message formats */
 
 /* NPA mailbox error codes
@@ -698,6 +720,9 @@
 	NIX_AF_ERR_INVALID_BANDPROF = -426,
 	NIX_AF_ERR_IPOLICER_NOTSUPP = -427,
 	NIX_AF_ERR_BANDPROF_INVAL_REQ  = -428,
+	NIX_AF_ERR_CQ_CTX_WRITE_ERR  = -429,
+	NIX_AF_ERR_AQ_CTX_RETRY_WRITE  = -430,
+	NIX_AF_ERR_LINK_CREDITS  = -431,
 };
 
 /* For NIX RX vtag action  */
@@ -949,6 +974,8 @@
 	 */
 };
 
+#define NIX_FLOW_KEY_TYPE_L3_L4_MASK (~(0xf << 28))
+
 struct nix_rss_flowkey_cfg {
 	struct mbox_msghdr hdr;
 	int	mcam_index;  /* MCAM entry index to modify */
@@ -974,6 +1001,10 @@
 #define NIX_FLOW_KEY_TYPE_IPV4_PROTO	BIT(21)
 #define NIX_FLOW_KEY_TYPE_AH		BIT(22)
 #define NIX_FLOW_KEY_TYPE_ESP		BIT(23)
+#define NIX_FLOW_KEY_TYPE_L4_DST_ONLY BIT(28)
+#define NIX_FLOW_KEY_TYPE_L4_SRC_ONLY BIT(29)
+#define NIX_FLOW_KEY_TYPE_L3_DST_ONLY BIT(30)
+#define NIX_FLOW_KEY_TYPE_L3_SRC_ONLY BIT(31)
 	u32	flowkey_cfg; /* Flowkey types selected */
 	u8	group;       /* RSS context or group */
 };
@@ -1417,7 +1448,9 @@
 	u16 nix_pf_func;
 	u16 sso_pf_func;
 	u16 eng_grpmsk;
-	int blkaddr;
+	u8 blkaddr;
+	u8 ctx_ilen_valid : 1;
+	u8 ctx_ilen : 7;
 };
 
 /* Mailbox message request and response format for CPT stats. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/npc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/npc.h
@@ -31,9 +31,9 @@
 	NPC_LT_LA_HIGIG2_ETHER,
 	NPC_LT_LA_IH_NIX_HIGIG2_ETHER,
 	NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-	NPC_LT_LA_CH_LEN_90B_ETHER,
 	NPC_LT_LA_CPT_HDR,
 	NPC_LT_LA_CUSTOM_L2_24B_ETHER,
+	NPC_LT_LA_CUSTOM_PRE_L2_ETHER,
 	NPC_LT_LA_CUSTOM0 = 0xE,
 	NPC_LT_LA_CUSTOM1 = 0xF,
 };
@@ -56,8 +56,13 @@
 	NPC_LT_LB_CUSTOM1 = 0xF,
 };
 
+/* Don't modify ltypes up to IP6_EXT, otherwise length and checksum of IP
+ * headers may not be checked correctly. IPv4 ltypes and IPv6 ltypes must
+ * differ only at bit 0 so mask 0xE can be used to detect extended headers.
+ */
 enum npc_kpu_lc_ltype {
-	NPC_LT_LC_IP = 1,
+	NPC_LT_LC_PTP = 1,
+	NPC_LT_LC_IP,
 	NPC_LT_LC_IP_OPT,
 	NPC_LT_LC_IP6,
 	NPC_LT_LC_IP6_EXT,
@@ -65,7 +70,6 @@
 	NPC_LT_LC_RARP,
 	NPC_LT_LC_MPLS,
 	NPC_LT_LC_NSH,
-	NPC_LT_LC_PTP,
 	NPC_LT_LC_FCOE,
 	NPC_LT_LC_NGIO,
 	NPC_LT_LC_CUSTOM0 = 0xE,
@@ -148,10 +152,11 @@
  * Software assigns pkind for each incoming port such as CGX
  * Ethernet interfaces, LBK interfaces, etc.
  */
-#define NPC_UNRESERVED_PKIND_COUNT NPC_RX_VLAN_EXDSA_PKIND
+#define NPC_UNRESERVED_PKIND_COUNT NPC_RX_CUSTOM_PRE_L2_PKIND
 
 enum npc_pkind_type {
 	NPC_RX_LBK_PKIND = 0ULL,
+	NPC_RX_CUSTOM_PRE_L2_PKIND = 55ULL,
 	NPC_RX_VLAN_EXDSA_PKIND = 56ULL,
 	NPC_RX_CHLEN24B_PKIND = 57ULL,
 	NPC_RX_CPT_HDR_PKIND,
@@ -162,6 +167,10 @@
 	NPC_TX_DEF_PKIND,	/* NIX-TX PKIND */
 };
 
+enum npc_interface_type {
+	NPC_INTF_MODE_DEF,
+};
+
 /* list of known and supported fields in packet header and
  * fields present in key structure.
  */
@@ -485,7 +494,7 @@
 	u8	ltype_mask;
 	u8	ltype_match;
 	u8	lid;
-};
+} __packed;
 
 struct npc_lt_def_ipsec {
 	u8	ltype_mask;
@@ -493,7 +502,7 @@
 	u8	lid;
 	u8	spi_offset;
 	u8	spi_nz;
-};
+} __packed;
 
 struct npc_lt_def_apad {
 	u8	ltype_mask;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/npc_profile.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/npc_profile.h
@@ -176,9 +176,8 @@
 	NPC_S_KPU1_EXDSA,
 	NPC_S_KPU1_HIGIG2,
 	NPC_S_KPU1_IH_NIX_HIGIG2,
-	NPC_S_KPU1_CUSTOM_L2_90B,
+	NPC_S_KPU1_CUSTOM_PRE_L2,
 	NPC_S_KPU1_CPT_HDR,
-	NPC_S_KPU1_CUSTOM_L2_24B,
 	NPC_S_KPU1_VLAN_EXDSA,
 	NPC_S_KPU2_CTAG,
 	NPC_S_KPU2_CTAG2,
@@ -187,7 +186,8 @@
 	NPC_S_KPU2_ETAG,
 	NPC_S_KPU2_PREHEADER,
 	NPC_S_KPU2_EXDSA,
-	NPC_S_KPU2_NGIO,
+	NPC_S_KPU2_CPT_CTAG,
+	NPC_S_KPU2_CPT_QINQ,
 	NPC_S_KPU3_CTAG,
 	NPC_S_KPU3_STAG,
 	NPC_S_KPU3_QINQ,
@@ -212,6 +212,7 @@
 	NPC_S_KPU5_NSH,
 	NPC_S_KPU5_CPT_IP,
 	NPC_S_KPU5_CPT_IP6,
+	NPC_S_KPU5_NGIO,
 	NPC_S_KPU6_IP6_EXT,
 	NPC_S_KPU6_IP6_HOP_DEST,
 	NPC_S_KPU6_IP6_ROUT,
@@ -979,8 +980,8 @@
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		12, 16, 20, 0, 0,
-		NPC_S_KPU1_ETHER, 0, 0,
-		NPC_LID_LA, NPC_LT_NA,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0, 1,
+		NPC_LID_LA, NPC_LT_LA_CUSTOM_PRE_L2_ETHER,
 		0,
 		0, 0, 0, 0,
 
@@ -996,27 +997,27 @@
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		36, 40, 44, 0, 0,
-		NPC_S_KPU1_CUSTOM_L2_24B, 0, 0,
-		NPC_LID_LA, NPC_LT_NA,
+		12, 16, 20, 0, 0,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 24, 1,
+		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
 		0,
 		0, 0, 0, 0,
 
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		40, 54, 58, 0, 0,
-		NPC_S_KPU1_CPT_HDR, 0, 0,
+		12, 16, 20, 0, 0,
+		NPC_S_KPU1_CPT_HDR, 40, 0,
 		NPC_LID_LA, NPC_LT_NA,
 		0,
-		0, 0, 0, 0,
+		7, 7, 0, 0,
 
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		102, 106, 110, 0, 0,
-		NPC_S_KPU1_CUSTOM_L2_90B, 0, 0,
-		NPC_LID_LA, NPC_LT_NA,
+		12, 16, 20, 0, 0,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 90, 1,
+		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
 		0,
 		0, 0, 0, 0,
 
@@ -1120,15 +1121,6 @@
 		NPC_S_KPU1_ETHER, 0xff,
 		NPC_ETYPE_CTAG,
 		0xffff,
-		NPC_ETYPE_NGIO,
-		0xffff,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_ETHER, 0xff,
-		NPC_ETYPE_CTAG,
-		0xffff,
 		NPC_ETYPE_CTAG,
 		0xffff,
 		0x0000,
@@ -1711,7 +1703,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_IP,
 		0xffff,
 		0x0000,
@@ -1720,7 +1712,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_IP6,
 		0xffff,
 		0x0000,
@@ -1729,7 +1721,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_ARP,
 		0xffff,
 		0x0000,
@@ -1738,7 +1730,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_RARP,
 		0xffff,
 		0x0000,
@@ -1747,7 +1739,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_PTP,
 		0xffff,
 		0x0000,
@@ -1756,7 +1748,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_FCOE,
 		0xffff,
 		0x0000,
@@ -1765,7 +1757,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_CTAG,
 		0xffff,
 		NPC_ETYPE_CTAG,
@@ -1774,7 +1766,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_CTAG,
 		0xffff,
 		0x0000,
@@ -1783,7 +1775,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_SBTAG,
 		0xffff,
 		0x0000,
@@ -1792,7 +1784,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_QINQ,
 		0xffff,
 		0x0000,
@@ -1801,7 +1793,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_ETAG,
 		0xffff,
 		0x0000,
@@ -1810,7 +1802,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_MPLSU,
 		0xffff,
 		0x0000,
@@ -1819,7 +1811,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_MPLSM,
 		0xffff,
 		0x0000,
@@ -1828,7 +1820,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		NPC_ETYPE_NSH,
 		0xffff,
 		0x0000,
@@ -1837,7 +1829,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_90B, 0xff,
+		NPC_S_KPU1_CUSTOM_PRE_L2, 0xff,
 		0x0000,
 		0x0000,
 		0x0000,
@@ -1847,150 +1839,24 @@
 	},
 	{
 		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
 		NPC_ETYPE_IP,
 		0xffff,
 		0x0000,
 		0x0000,
-	},
-	{
-		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
-		NPC_ETYPE_IP6,
-		0xffff,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
-		NPC_ETYPE_CTAG,
-		0xffff,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
-		NPC_ETYPE_QINQ,
-		0xffff,
 		0x0000,
 		0x0000,
 	},
 	{
 		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
-		0x0000,
-		0x0000,
-		NPC_ETYPE_IP,
-		0xffff,
-	},
-	{
-		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
-		0x0000,
-		0x0000,
 		NPC_ETYPE_IP6,
 		0xffff,
-	},
-	{
-		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0xffff,
-		0x0000,
 		0x0000,
-		NPC_ETYPE_CTAG,
-		0xffff,
-	},
-	{
-		NPC_S_KPU1_CPT_HDR, 0xff,
 		0x0000,
-		0xffff,
 		0x0000,
 		0x0000,
-		NPC_ETYPE_QINQ,
-		0xffff,
 	},
 	{
 		NPC_S_KPU1_CPT_HDR, 0xff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_IP,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_IP6,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_ARP,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_RARP,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_PTP,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_FCOE,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_CTAG,
-		0xffff,
-		NPC_ETYPE_CTAG,
-		0xffff,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
 		NPC_ETYPE_CTAG,
 		0xffff,
 		0x0000,
@@ -1999,16 +1865,7 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_SBTAG,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
+		NPC_S_KPU1_CPT_HDR, 0xff,
 		NPC_ETYPE_QINQ,
 		0xffff,
 		0x0000,
@@ -2017,51 +1874,6 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_ETAG,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_MPLSU,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_MPLSM,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		NPC_ETYPE_NSH,
-		0xffff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
-		NPC_S_KPU1_CUSTOM_L2_24B, 0xff,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-		0x0000,
-	},
-	{
 		NPC_S_KPU1_VLAN_EXDSA, 0xff,
 		NPC_ETYPE_CTAG,
 		0xffff,
@@ -2167,6 +1979,15 @@
 	},
 	{
 		NPC_S_KPU2_CTAG, 0xff,
+		NPC_ETYPE_NGIO,
+		0xffff,
+		0x0000,
+		0x0000,
+		0x0000,
+		0x0000,
+	},
+	{
+		NPC_S_KPU2_CTAG, 0xff,
 		NPC_ETYPE_PPPOE,
 		0xffff,
 		0x0000,
@@ -3057,11 +2878,38 @@
 		0x0000,
 	},
 	{
-		NPC_S_KPU2_NGIO, 0xff,
+		NPC_S_KPU2_CPT_CTAG, 0xff,
+		NPC_ETYPE_IP,
+		0xffff,
 		0x0000,
 		0x0000,
 		0x0000,
 		0x0000,
+	},
+	{
+		NPC_S_KPU2_CPT_CTAG, 0xff,
+		NPC_ETYPE_IP6,
+		0xffff,
+		0x0000,
+		0x0000,
+		0x0000,
+		0x0000,
+	},
+	{
+		NPC_S_KPU2_CPT_QINQ, 0xff,
+		NPC_ETYPE_CTAG,
+		0xffff,
+		NPC_ETYPE_IP,
+		0xffff,
+		0x0000,
+		0x0000,
+	},
+	{
+		NPC_S_KPU2_CPT_QINQ, 0xff,
+		NPC_ETYPE_CTAG,
+		0xffff,
+		NPC_ETYPE_IP6,
+		0xffff,
 		0x0000,
 		0x0000,
 	},
@@ -5349,6 +5197,15 @@
 		0x0000,
 	},
 	{
+		NPC_S_KPU5_NGIO, 0xff,
+		0x0000,
+		0x0000,
+		0x0000,
+		0x0000,
+		0x0000,
+		0x0000,
+	},
+	{
 		NPC_S_NA, 0X00,
 		0x0000,
 		0x0000,
@@ -8645,14 +8502,6 @@
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		8, 12, 0, 0, 0,
-		NPC_S_KPU2_NGIO, 12, 1,
-		NPC_LID_LA, NPC_LT_LA_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		8, 12, 0, 0, 0,
 		NPC_S_KPU2_CTAG2, 12, 1,
 		NPC_LID_LA, NPC_LT_LA_ETHER,
 		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
@@ -9192,159 +9041,127 @@
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		8, 0, 6, 3, 0,
-		NPC_S_KPU5_IP, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
+		NPC_S_KPU5_IP, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		6, 0, 0, 3, 0,
-		NPC_S_KPU5_IP6, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
+		NPC_S_KPU5_IP6, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		0, 0, 0, 3, 0,
-		NPC_S_KPU5_ARP, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
+		NPC_S_KPU5_ARP, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		0, 0, 0, 3, 0,
-		NPC_S_KPU5_RARP, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
+		NPC_S_KPU5_RARP, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		0, 0, 0, 3, 0,
-		NPC_S_KPU5_PTP, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
+		NPC_S_KPU5_PTP, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		0, 0, 0, 3, 0,
-		NPC_S_KPU5_FCOE, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
+		NPC_S_KPU5_FCOE, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		8, 12, 0, 0, 0,
-		NPC_S_KPU2_CTAG2, 102, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
+		NPC_S_KPU2_CTAG2, 12, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		4, 8, 0, 0, 0,
-		NPC_S_KPU2_CTAG, 102, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
+		NPC_S_KPU2_CTAG, 12, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		4, 8, 22, 0, 0,
-		NPC_S_KPU2_SBTAG, 102, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
+		NPC_S_KPU2_SBTAG, 12, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		4, 8, 0, 0, 0,
-		NPC_S_KPU2_QINQ, 102, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
+		NPC_S_KPU2_QINQ, 12, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		8, 12, 26, 0, 0,
-		NPC_S_KPU2_ETAG, 102, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_ETAG,
+		NPC_S_KPU2_ETAG, 12, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		2, 6, 10, 2, 0,
-		NPC_S_KPU4_MPLS, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_L_WITH_MPLS,
+		NPC_S_KPU4_MPLS, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		2, 6, 10, 2, 0,
-		NPC_S_KPU4_MPLS, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_L_WITH_MPLS,
+		NPC_S_KPU4_MPLS, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
+		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		2, 0, 0, 2, 0,
-		NPC_S_KPU4_NSH, 104, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_L_WITH_NSH,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 0, 1,
-		NPC_S_NA, 0, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_90B_ETHER,
-		NPC_F_LA_L_UNK_ETYPE,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		8, 0, 6, 3, 0,
-		NPC_S_KPU5_CPT_IP, 56, 1,
-		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
+		NPC_S_KPU4_NSH, 14, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		6, 0, 0, 3, 0,
-		NPC_S_KPU5_CPT_IP6, 56, 1,
-		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
+		0, 0, 0, 0, 1,
+		NPC_S_NA, 0, 0,
+		NPC_LID_LA, NPC_LT_NA,
 		0,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		4, 8, 0, 0, 0,
-		NPC_S_KPU2_CTAG, 54, 1,
-		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		4, 8, 0, 0, 0,
-		NPC_S_KPU2_QINQ, 54, 1,
-		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		8, 0, 6, 3, 0,
-		NPC_S_KPU5_CPT_IP, 60, 1,
+		NPC_S_KPU5_CPT_IP, 14, 1,
 		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
 		0,
 		0, 0, 0, 0,
@@ -9352,7 +9169,7 @@
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		6, 0, 0, 3, 0,
-		NPC_S_KPU5_CPT_IP6, 60, 1,
+		NPC_S_KPU5_CPT_IP6, 14, 1,
 		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
 		0,
 		0, 0, 0, 0,
@@ -9360,7 +9177,7 @@
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		4, 8, 0, 0, 0,
-		NPC_S_KPU2_CTAG, 58, 1,
+		NPC_S_KPU2_CPT_CTAG, 12, 1,
 		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
 		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
 		0, 0, 0, 0,
@@ -9368,141 +9185,13 @@
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		4, 8, 0, 0, 0,
-		NPC_S_KPU2_QINQ, 58, 1,
+		NPC_S_KPU2_CPT_QINQ, 12, 1,
 		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
 		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
 		0, 0, 0, 0,
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 0, 1,
-		NPC_S_NA, 0, 1,
-		NPC_LID_LA, NPC_LT_LA_CPT_HDR,
-		NPC_F_LA_L_UNK_ETYPE,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		8, 0, 6, 3, 0,
-		NPC_S_KPU5_IP, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		6, 0, 0, 3, 0,
-		NPC_S_KPU5_IP6, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 3, 0,
-		NPC_S_KPU5_ARP, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 3, 0,
-		NPC_S_KPU5_RARP, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 3, 0,
-		NPC_S_KPU5_PTP, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 3, 0,
-		NPC_S_KPU5_FCOE, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		0,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		8, 12, 0, 0, 0,
-		NPC_S_KPU2_CTAG2, 36, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		4, 8, 0, 0, 0,
-		NPC_S_KPU2_CTAG, 36, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		4, 8, 22, 0, 0,
-		NPC_S_KPU2_SBTAG, 36, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		4, 8, 0, 0, 0,
-		NPC_S_KPU2_QINQ, 36, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_VLAN,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		8, 12, 26, 0, 0,
-		NPC_S_KPU2_ETAG, 36, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_U_HAS_TAG | NPC_F_LA_L_WITH_ETAG,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		2, 6, 10, 2, 0,
-		NPC_S_KPU4_MPLS, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_L_WITH_MPLS,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		2, 6, 10, 2, 0,
-		NPC_S_KPU4_MPLS, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_L_WITH_MPLS,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		2, 0, 0, 2, 0,
-		NPC_S_KPU4_NSH, 38, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_L_WITH_NSH,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 0, 1,
-		NPC_S_NA, 0, 1,
-		NPC_LID_LA, NPC_LT_LA_CUSTOM_L2_24B_ETHER,
-		NPC_F_LA_L_UNK_ETYPE,
-		0, 0, 0, 0,
-	},
-	{
-		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		12, 0, 0, 1, 0,
 		NPC_S_KPU3_VLAN_EXDSA, 12, 1,
 		NPC_LID_LA, NPC_LT_LA_ETHER,
@@ -9596,6 +9285,14 @@
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
+		0, 0, 0, 2, 0,
+		NPC_S_KPU5_NGIO, 6, 1,
+		NPC_LID_LB, NPC_LT_LB_CTAG,
+		0,
+		0, 0, 0, 0,
+	},
+	{
+		NPC_ERRLEV_RE, NPC_EC_NOERR,
 		8, 0, 6, 2, 0,
 		NPC_S_KPU5_IP, 14, 1,
 		NPC_LID_LB, NPC_LT_LB_PPPOE,
@@ -10388,13 +10085,37 @@
 	},
 	{
 		NPC_ERRLEV_RE, NPC_EC_NOERR,
-		0, 0, 0, 0, 1,
-		NPC_S_NA, 0, 1,
-		NPC_LID_LC, NPC_LT_LC_NGIO,
+		8, 0, 6, 2, 0,
+		NPC_S_KPU5_CPT_IP, 6, 1,
+		NPC_LID_LB, NPC_LT_LB_CTAG,
+		0,
+		0, 0, 0, 0,
+	},
+	{
+		NPC_ERRLEV_RE, NPC_EC_NOERR,
+		6, 0, 0, 2, 0,
+		NPC_S_KPU5_CPT_IP6, 6, 1,
+		NPC_LID_LB, NPC_LT_LB_CTAG,
 		0,
 		0, 0, 0, 0,
 	},
 	{
+		NPC_ERRLEV_RE, NPC_EC_NOERR,
+		8, 0, 6, 2, 0,
+		NPC_S_KPU5_CPT_IP, 10, 1,
+		NPC_LID_LB, NPC_LT_LB_STAG_QINQ,
+		NPC_F_LB_U_MORE_TAG | NPC_F_LB_L_WITH_CTAG,
+		0, 0, 0, 0,
+	},
+	{
+		NPC_ERRLEV_RE, NPC_EC_NOERR,
+		6, 0, 0, 2, 0,
+		NPC_S_KPU5_CPT_IP6, 10, 1,
+		NPC_LID_LB, NPC_LT_LB_STAG_QINQ,
+		NPC_F_LB_U_MORE_TAG | NPC_F_LB_L_WITH_CTAG,
+		0, 0, 0, 0,
+	},
+	{
 		NPC_ERRLEV_LB, NPC_EC_L2_K3,
 		0, 0, 0, 0, 1,
 		NPC_S_NA, 0, 0,
@@ -12425,6 +12146,14 @@
 		0,
 		0, 0, 0, 0,
 	},
+	{
+		NPC_ERRLEV_RE, NPC_EC_NOERR,
+		0, 0, 0, 0, 1,
+		NPC_S_NA, 0, 1,
+		NPC_LID_LC, NPC_LT_LC_NGIO,
+		0,
+		0, 0, 0, 0,
+	},
 	{
 		NPC_ERRLEV_LC, NPC_EC_UNK,
 		0, 0, 0, 0, 1,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/ptp.c
@@ -85,6 +85,8 @@
 	/* Check driver is bound to PTP block */
 	if (!ptp)
 		ptp = ERR_PTR(-EPROBE_DEFER);
+	else
+		pci_dev_get(ptp->pdev);
 
 	return ptp;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rpm.c
@@ -22,6 +22,7 @@
 	.tx_stats_cnt   =       34,
 	.get_nr_lmacs	=	rpm_get_nr_lmacs,
 	.get_lmac_type  =       rpm_get_lmac_type,
+	.lmac_fifo_len	=	rpm_get_lmac_fifo_len,
 	.mac_lmac_intl_lbk =    rpm_lmac_internal_loopback,
 	.mac_get_rx_stats  =	rpm_get_rx_stats,
 	.mac_get_tx_stats  =	rpm_get_tx_stats,
@@ -29,6 +30,9 @@
 	.mac_get_pause_frm_status =	rpm_lmac_get_pause_frm_status,
 	.mac_enadis_pause_frm =		rpm_lmac_enadis_pause_frm,
 	.mac_pause_frm_config =		rpm_lmac_pause_frm_config,
+	.mac_enadis_ptp_config =	rpm_lmac_ptp_config,
+	.mac_rx_tx_enable =		rpm_lmac_rx_tx_enable,
+	.mac_tx_enable =		rpm_lmac_tx_enable,
 };
 
 struct mac_ops *rpm_get_mac_ops(void)
@@ -53,6 +57,43 @@
 	return hweight8(rpm_read(rpm, 0, CGXX_CMRX_RX_LMACS) & 0xFULL);
 }
 
+int rpm_lmac_tx_enable(void *rpmd, int lmac_id, bool enable)
+{
+	rpm_t *rpm = rpmd;
+	u64 cfg, last;
+
+	if (!is_lmac_valid(rpm, lmac_id))
+		return -ENODEV;
+
+	cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
+	last = cfg;
+	if (enable)
+		cfg |= RPM_TX_EN;
+	else
+		cfg &= ~(RPM_TX_EN);
+
+	if (cfg != last)
+		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
+	return !!(last & RPM_TX_EN);
+}
+
+int rpm_lmac_rx_tx_enable(void *rpmd, int lmac_id, bool enable)
+{
+	rpm_t *rpm = rpmd;
+	u64 cfg;
+
+	if (!is_lmac_valid(rpm, lmac_id))
+		return -ENODEV;
+
+	cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
+	if (enable)
+		cfg |= RPM_RX_EN | RPM_TX_EN;
+	else
+		cfg &= ~(RPM_RX_EN | RPM_TX_EN);
+	rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
+	return 0;
+}
+
 void rpm_lmac_enadis_rx_pause_fwding(void *rpmd, int lmac_id, bool enable)
 {
 	rpm_t *rpm = rpmd;
@@ -127,26 +168,6 @@
 	u64 cfg;
 
 	if (enable) {
-		/* Enable 802.3 pause frame mode */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg &= ~RPMX_MTI_MAC100X_COMMAND_CONFIG_PFC_MODE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
-
-		/* Enable receive pause frames */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg &= ~RPMX_MTI_MAC100X_COMMAND_CONFIG_RX_P_DISABLE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
-
-		/* Enable forward pause to TX block */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg &= ~RPMX_MTI_MAC100X_COMMAND_CONFIG_PAUSE_IGNORE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
-
-		/* Enable pause frames transmission */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg &= ~RPMX_MTI_MAC100X_COMMAND_CONFIG_TX_P_DISABLE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
-
 		/* Set pause time and interval */
 		cfg = rpm_read(rpm, lmac_id,
 			       RPMX_MTI_MAC100X_CL01_PAUSE_QUANTA);
@@ -159,23 +180,22 @@
 		cfg &= ~0xFFFFULL;
 		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_CL01_QUANTA_THRESH,
 			  cfg | (RPM_DEFAULT_PAUSE_TIME / 2));
+	}
 
-	} else {
-		/* ALL pause frames received are completely ignored */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg |= RPMX_MTI_MAC100X_COMMAND_CONFIG_RX_P_DISABLE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
+	/* ALL pause frames received are completely ignored */
+	cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
+	cfg |= RPMX_MTI_MAC100X_COMMAND_CONFIG_RX_P_DISABLE;
+	rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
 
-		/* Disable forward pause to TX block */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg |= RPMX_MTI_MAC100X_COMMAND_CONFIG_PAUSE_IGNORE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
+	/* Disable forward pause to TX block */
+	cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
+	cfg |= RPMX_MTI_MAC100X_COMMAND_CONFIG_PAUSE_IGNORE;
+	rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
 
-		/* Disable pause frames transmission */
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
-		cfg |= RPMX_MTI_MAC100X_COMMAND_CONFIG_TX_P_DISABLE;
-		rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
-	}
+	/* Disable pause frames transmission */
+	cfg = rpm_read(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG);
+	cfg |= RPMX_MTI_MAC100X_COMMAND_CONFIG_TX_P_DISABLE;
+	rpm_write(rpm, lmac_id, RPMX_MTI_MAC100X_COMMAND_CONFIG, cfg);
 }
 
 int rpm_get_rx_stats(void *rpmd, int lmac_id, int idx, u64 *rx_stat)
@@ -236,12 +256,41 @@
 	int err;
 
 	req = FIELD_SET(CMDREG_ID, CGX_CMD_GET_LINK_STS, req);
-	err = cgx_fwi_cmd_generic(req, &resp, rpm, 0);
+	err = cgx_fwi_cmd_generic(req, &resp, rpm, lmac_id);
 	if (!err)
 		return FIELD_GET(RESP_LINKSTAT_LMAC_TYPE, resp);
 	return err;
 }
 
+u32 rpm_get_lmac_fifo_len(void *rpmd, int lmac_id)
+{
+	rpm_t *rpm = rpmd;
+	u64 hi_perf_lmac;
+	u8 num_lmacs;
+	u32 fifo_len;
+
+	fifo_len = rpm->mac_ops->fifo_len;
+	num_lmacs = rpm->mac_ops->get_nr_lmacs(rpm);
+
+	switch (num_lmacs) {
+	case 1:
+		return fifo_len;
+	case 2:
+		return fifo_len / 2;
+	case 3:
+		/* LMAC marked as hi_perf gets half of the FIFO and rest 1/4th */
+		hi_perf_lmac = rpm_read(rpm, 0, CGXX_CMRX_RX_LMACS);
+		hi_perf_lmac = (hi_perf_lmac >> 4) & 0x3ULL;
+		if (lmac_id == hi_perf_lmac)
+			return fifo_len / 2;
+		return fifo_len / 4;
+	case 4:
+	default:
+		return fifo_len / 4;
+	}
+	return 0;
+}
+
 int rpm_lmac_internal_loopback(void *rpmd, int lmac_id, bool enable)
 {
 	rpm_t *rpm = rpmd;
@@ -251,22 +300,35 @@
 	if (!rpm || lmac_id >= rpm->lmac_count)
 		return -ENODEV;
 	lmac_type = rpm->mac_ops->get_lmac_type(rpm, lmac_id);
-	if (lmac_type == LMAC_MODE_100G_R) {
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_PCS100X_CONTROL1);
 
-		if (enable)
-			cfg |= RPMX_MTI_PCS_LBK;
-		else
-			cfg &= ~RPMX_MTI_PCS_LBK;
-		rpm_write(rpm, lmac_id, RPMX_MTI_PCS100X_CONTROL1, cfg);
-	} else {
-		cfg = rpm_read(rpm, lmac_id, RPMX_MTI_LPCSX_CONTROL1);
-		if (enable)
-			cfg |= RPMX_MTI_PCS_LBK;
-		else
-			cfg &= ~RPMX_MTI_PCS_LBK;
-		rpm_write(rpm, lmac_id, RPMX_MTI_LPCSX_CONTROL1, cfg);
+	if (lmac_type == LMAC_MODE_QSGMII || lmac_type == LMAC_MODE_SGMII) {
+		dev_err(&rpm->pdev->dev, "loopback not supported for LPC mode\n");
+		return 0;
 	}
 
+	cfg = rpm_read(rpm, lmac_id, RPMX_MTI_PCS100X_CONTROL1);
+
+	if (enable)
+		cfg |= RPMX_MTI_PCS_LBK;
+	else
+		cfg &= ~RPMX_MTI_PCS_LBK;
+	rpm_write(rpm, lmac_id, RPMX_MTI_PCS100X_CONTROL1, cfg);
+
 	return 0;
 }
+
+void rpm_lmac_ptp_config(void *rpmd, int lmac_id, bool enable)
+{
+	rpm_t *rpm = rpmd;
+	u64 cfg;
+
+	if (!is_lmac_valid(rpm, lmac_id))
+		return;
+
+	cfg = rpm_read(rpm, lmac_id, RPMX_CMRX_CFG);
+	if (enable)
+		cfg |= RPMX_RX_TS_PREPEND;
+	else
+		cfg &= ~RPMX_RX_TS_PREPEND;
+	rpm_write(rpm, lmac_id, RPMX_CMRX_CFG, cfg);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rpm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rpm.h
@@ -14,6 +14,8 @@
 #define PCI_DEVID_CN10K_RPM		0xA060
 
 /* Registers */
+#define RPMX_CMRX_CFG			0x00
+#define RPMX_RX_TS_PREPEND              BIT_ULL(22)
 #define RPMX_CMRX_SW_INT                0x180
 #define RPMX_CMRX_SW_INT_W1S            0x188
 #define RPMX_CMRX_SW_INT_ENA_W1S        0x198
@@ -41,10 +43,13 @@
 #define RPMX_MTI_STAT_DATA_HI_CDC            0x10038
 
 #define RPM_LMAC_FWI			0xa
+#define RPM_TX_EN			BIT_ULL(0)
+#define RPM_RX_EN			BIT_ULL(1)
 
 /* Function Declarations */
 int rpm_get_nr_lmacs(void *rpmd);
 u8 rpm_get_lmac_type(void *rpmd, int lmac_id);
+u32 rpm_get_lmac_fifo_len(void *rpmd, int lmac_id);
 int rpm_lmac_internal_loopback(void *rpmd, int lmac_id, bool enable);
 void rpm_lmac_enadis_rx_pause_fwding(void *rpmd, int lmac_id, bool enable);
 int rpm_lmac_get_pause_frm_status(void *cgxd, int lmac_id, u8 *tx_pause,
@@ -54,4 +59,7 @@
 			      u8 rx_pause);
 int rpm_get_tx_stats(void *rpmd, int lmac_id, int idx, u64 *tx_stat);
 int rpm_get_rx_stats(void *rpmd, int lmac_id, int idx, u64 *rx_stat);
+void rpm_lmac_ptp_config(void *rpmd, int lmac_id, bool enable);
+int rpm_lmac_rx_tx_enable(void *rpmd, int lmac_id, bool enable);
+int rpm_lmac_tx_enable(void *rpmd, int lmac_id, bool enable);
 #endif /* RPM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu.c
@@ -520,8 +520,11 @@
 
 	rvu_write64(rvu, blkaddr, rst_reg, BIT_ULL(0));
 	err = rvu_poll_reg(rvu, blkaddr, rst_reg, BIT_ULL(63), true);
-	if (err)
-		dev_err(rvu->dev, "HW block:%d reset failed\n", blkaddr);
+	if (err) {
+		dev_err(rvu->dev, "HW block:%d reset timeout retrying again\n", blkaddr);
+		while (rvu_poll_reg(rvu, blkaddr, rst_reg, BIT_ULL(63), true) == -EBUSY)
+			;
+	}
 }
 
 static void rvu_reset_all_blocks(struct rvu *rvu)
@@ -1550,7 +1553,7 @@
 		if (req->ssow > block->lf.max) {
 			dev_err(&rvu->pdev->dev,
 				"Func 0x%x: Invalid SSOW req, %d > max %d\n",
-				 pcifunc, req->sso, block->lf.max);
+				 pcifunc, req->ssow, block->lf.max);
 			return -EINVAL;
 		}
 		mappedlfs = rvu_get_rsrc_mapcount(pfvf, block->addr);
@@ -2193,7 +2196,7 @@
 }
 
 static int rvu_get_mbox_regions(struct rvu *rvu, void **mbox_addr,
-				int num, int type)
+				int num, int type, unsigned long *pf_bmap)
 {
 	struct rvu_hwinfo *hw = rvu->hw;
 	int region;
@@ -2205,6 +2208,9 @@
 	 */
 	if (type == TYPE_AFVF) {
 		for (region = 0; region < num; region++) {
+			if (!test_bit(region, pf_bmap))
+				continue;
+
 			if (hw->cap.per_pf_mbox_regs) {
 				bar4 = rvu_read64(rvu, BLKADDR_RVUM,
 						  RVU_AF_PFX_BAR4_ADDR(0)) +
@@ -2226,6 +2232,9 @@
 	 * RVU_AF_PF_BAR4_ADDR register.
 	 */
 	for (region = 0; region < num; region++) {
+		if (!test_bit(region, pf_bmap))
+			continue;
+
 		if (hw->cap.per_pf_mbox_regs) {
 			bar4 = rvu_read64(rvu, BLKADDR_RVUM,
 					  RVU_AF_PFX_BAR4_ADDR(region));
@@ -2254,20 +2263,41 @@
 	int err = -EINVAL, i, dir, dir_up;
 	void __iomem *reg_base;
 	struct rvu_work *mwork;
+	unsigned long *pf_bmap;
 	void **mbox_regions;
 	const char *name;
+	u64 cfg;
 
-	mbox_regions = kcalloc(num, sizeof(void *), GFP_KERNEL);
-	if (!mbox_regions)
+	pf_bmap = bitmap_zalloc(num, GFP_KERNEL);
+	if (!pf_bmap)
 		return -ENOMEM;
 
+	/* RVU VFs */
+	if (type == TYPE_AFVF)
+		bitmap_set(pf_bmap, 0, num);
+
+	if (type == TYPE_AFPF) {
+		/* Mark enabled PFs in bitmap */
+		for (i = 0; i < num; i++) {
+			cfg = rvu_read64(rvu, BLKADDR_RVUM, RVU_PRIV_PFX_CFG(i));
+			if (cfg & BIT_ULL(20))
+				set_bit(i, pf_bmap);
+		}
+	}
+
+	mbox_regions = kcalloc(num, sizeof(void *), GFP_KERNEL);
+	if (!mbox_regions) {
+		err = -ENOMEM;
+		goto free_bitmap;
+	}
+
 	switch (type) {
 	case TYPE_AFPF:
 		name = "rvu_afpf_mailbox";
 		dir = MBOX_DIR_AFPF;
 		dir_up = MBOX_DIR_AFPF_UP;
 		reg_base = rvu->afreg_base;
-		err = rvu_get_mbox_regions(rvu, mbox_regions, num, TYPE_AFPF);
+		err = rvu_get_mbox_regions(rvu, mbox_regions, num, TYPE_AFPF, pf_bmap);
 		if (err)
 			goto free_regions;
 		break;
@@ -2276,12 +2306,12 @@
 		dir = MBOX_DIR_PFVF;
 		dir_up = MBOX_DIR_PFVF_UP;
 		reg_base = rvu->pfreg_base;
-		err = rvu_get_mbox_regions(rvu, mbox_regions, num, TYPE_AFVF);
+		err = rvu_get_mbox_regions(rvu, mbox_regions, num, TYPE_AFVF, pf_bmap);
 		if (err)
 			goto free_regions;
 		break;
 	default:
-		return err;
+		goto free_regions;
 	}
 
 	mw->mbox_wq = alloc_workqueue(name,
@@ -2307,16 +2337,19 @@
 	}
 
 	err = otx2_mbox_regions_init(&mw->mbox, mbox_regions, rvu->pdev,
-				     reg_base, dir, num);
+				     reg_base, dir, num, pf_bmap);
 	if (err)
 		goto exit;
 
 	err = otx2_mbox_regions_init(&mw->mbox_up, mbox_regions, rvu->pdev,
-				     reg_base, dir_up, num);
+				     reg_base, dir_up, num, pf_bmap);
 	if (err)
 		goto exit;
 
 	for (i = 0; i < num; i++) {
+		if (!test_bit(i, pf_bmap))
+			continue;
+
 		mwork = &mw->mbox_wrk[i];
 		mwork->rvu = rvu;
 		INIT_WORK(&mwork->work, mbox_handler);
@@ -2325,8 +2358,7 @@
 		mwork->rvu = rvu;
 		INIT_WORK(&mwork->work, mbox_up_handler);
 	}
-	kfree(mbox_regions);
-	return 0;
+	goto free_regions;
 
 exit:
 	destroy_workqueue(mw->mbox_wq);
@@ -2335,6 +2367,8 @@
 		iounmap((void __iomem *)mbox_regions[num]);
 free_regions:
 	kfree(mbox_regions);
+free_bitmap:
+	bitmap_free(pf_bmap);
 	return err;
 }
 
@@ -2401,10 +2435,9 @@
 	}
 }
 
-static irqreturn_t rvu_mbox_intr_handler(int irq, void *rvu_irq)
+static irqreturn_t rvu_mbox_pf_intr_handler(int irq, void *rvu_irq)
 {
 	struct rvu *rvu = (struct rvu *)rvu_irq;
-	int vfs = rvu->vfs;
 	u64 intr;
 
 	intr = rvu_read64(rvu, BLKADDR_RVUM, RVU_AF_PFAF_MBOX_INT);
@@ -2418,13 +2451,25 @@
 
 	rvu_queue_work(&rvu->afpf_wq_info, 0, rvu->hw->total_pfs, intr);
 
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t rvu_mbox_intr_handler(int irq, void *rvu_irq)
+{
+	struct rvu *rvu = (struct rvu *)rvu_irq;
+	int vfs = rvu->vfs;
+	u64 intr;
+
+	/* Sync with mbox memory region */
+	rmb();
+
 	/* Handle VF interrupts */
 	if (vfs > 64) {
 		intr = rvupf_read64(rvu, RVU_PF_VFPF_MBOX_INTX(1));
 		rvupf_write64(rvu, RVU_PF_VFPF_MBOX_INTX(1), intr);
 
 		rvu_queue_work(&rvu->afvf_wq_info, 64, vfs, intr);
-		vfs -= 64;
+		vfs = 64;
 	}
 
 	intr = rvupf_read64(rvu, RVU_PF_VFPF_MBOX_INTX(0));
@@ -2501,6 +2546,12 @@
 	rvu_blklf_teardown(rvu, pcifunc, BLKADDR_NPA);
 	rvu_reset_lmt_map_tbl(rvu, pcifunc);
 	rvu_detach_rsrcs(rvu, NULL, pcifunc);
+	/* In scenarios where PF/VF drivers detach NIXLF without freeing MCAM
+	 * entries, check and free the MCAM entries explicitly to avoid leak.
+	 * Since LF is detached use LF number as -1.
+	 */
+	rvu_npc_free_mcam_entries(rvu, pcifunc, -1);
+
 	mutex_unlock(&rvu->flr_lock);
 }
 
@@ -2739,7 +2790,7 @@
 	/* Register mailbox interrupt handler */
 	sprintf(&rvu->irq_name[RVU_AF_INT_VEC_MBOX * NAME_SIZE], "RVUAF Mbox");
 	ret = request_irq(pci_irq_vector(rvu->pdev, RVU_AF_INT_VEC_MBOX),
-			  rvu_mbox_intr_handler, 0,
+			  rvu_mbox_pf_intr_handler, 0,
 			  &rvu->irq_name[RVU_AF_INT_VEC_MBOX * NAME_SIZE], rvu);
 	if (ret) {
 		dev_err(rvu->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu.h
@@ -23,6 +23,7 @@
 #define	PCI_DEVID_OCTEONTX2_LBK			0xA061
 
 /* Subsystem Device ID */
+#define PCI_SUBSYS_DEVID_98XX                  0xB100
 #define PCI_SUBSYS_DEVID_96XX                  0xB200
 #define PCI_SUBSYS_DEVID_CN10K_A	       0xB900
 
@@ -220,6 +221,7 @@
 	u16		maxlen;
 	u16		minlen;
 
+	bool		hw_rx_tstamp_en; /* Is rx_tstamp enabled */
 	u8		mac_addr[ETH_ALEN]; /* MAC address of this PF/VF */
 	u8		default_mac[ETH_ALEN]; /* MAC address from FWdata */
 
@@ -237,6 +239,7 @@
 	bool	cgx_in_use; /* this PF/VF using CGX? */
 	int	cgx_users;  /* number of cgx users - used only by PFs */
 
+	int     intf_mode;
 	u8	nix_blkaddr; /* BLKADDR_NIX0/1 assigned to this PF */
 	u8	nix_rx_intf; /* NIX0_RX/NIX1_RX interface to NPC */
 	u8	nix_tx_intf; /* NIX0_TX/NIX1_TX interface to NPC */
@@ -274,6 +277,21 @@
 	u32 *cfg;
 };
 
+/* smq(flush) to tl1 cir/pir info */
+struct nix_smq_tree_ctx {
+	u16 schq;
+	u64 cir_off;
+	u64 cir_val;
+	u64 pir_off;
+	u64 pir_val;
+};
+
+/* smq flush context */
+struct nix_smq_flush_ctx {
+	int smq;
+	struct nix_smq_tree_ctx smq_tree_ctx[NIX_TXSCH_LVL_CNT];
+};
+
 struct npc_pkind {
 	struct rsrc_bmap rsrc;
 	u32	*pfchan_map;
@@ -612,6 +630,16 @@
 	return rvu->hw->cpt_chan_base + chan;
 }
 
+static inline bool is_rvu_supports_nix1(struct rvu *rvu)
+{
+	struct pci_dev *pdev = rvu->pdev;
+
+	if (pdev->subsystem_device == PCI_SUBSYS_DEVID_98XX)
+		return true;
+
+	return false;
+}
+
 /* Function Prototypes
  * RVU
  */
@@ -794,11 +822,14 @@
 void npc_read_mcam_entry(struct rvu *rvu, struct npc_mcam *mcam,
 			 int blkaddr, u16 src, struct mcam_entry *entry,
 			 u8 *intf, u8 *ena);
+bool is_cgx_config_permitted(struct rvu *rvu, u16 pcifunc);
 bool is_mac_feature_supported(struct rvu *rvu, int pf, int feature);
 u32  rvu_cgx_get_fifolen(struct rvu *rvu);
 void *rvu_first_cgx_pdata(struct rvu *rvu);
 int cgxlmac_to_pf(struct rvu *rvu, int cgx_id, int lmac_id);
-
+int rvu_cgx_config_tx(void *cgxd, int lmac_id, bool enable);
+int rvu_cgx_tx_enable(struct rvu *rvu, u16 pcifunc, bool enable);
+u32 rvu_cgx_get_lmac_fifolen(struct rvu *rvu, int cgx, int lmac);
 int npc_get_nixlf_mcam_index(struct npc_mcam *mcam, u16 pcifunc, int nixlf,
 			     int type);
 bool is_mcam_entry_enabled(struct rvu *rvu, struct npc_mcam *mcam, int blkaddr,
@@ -807,6 +838,9 @@
 /* CPT APIs */
 int rvu_cpt_lf_teardown(struct rvu *rvu, u16 pcifunc, int lf, int slot);
 
+#define NDC_AF_BANK_MASK       GENMASK_ULL(7, 0)
+#define NDC_AF_BANK_LINE_MASK  GENMASK_ULL(31, 16)
+
 /* CN10K RVU */
 int rvu_set_channels_base(struct rvu *rvu);
 void rvu_program_channels(struct rvu *rvu);
@@ -822,9 +856,14 @@
 static inline void rvu_dbg_exit(struct rvu *rvu) {}
 #endif
 
+int rvu_ndc_fix_locked_cacheline(struct rvu *rvu, int blkaddr);
+
 /* RVU Switch */
 void rvu_switch_enable(struct rvu *rvu);
 void rvu_switch_disable(struct rvu *rvu);
 void rvu_switch_update_rules(struct rvu *rvu, u16 pcifunc);
 
+int rvu_npc_set_parse_mode(struct rvu *rvu, u16 pcifunc, u64 mode, u8 dir,
+			   u64 pkind, u8 var_len_off, u8 var_len_off_mask,
+			   u8 shift_dir);
 #endif /* RVU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_cgx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_cgx.c
@@ -111,7 +111,7 @@
 	p2x = cgx_lmac_get_p2x(cgx_id, lmac_id);
 	/* Firmware sets P2X_SELECT as either NIX0 or NIX1 */
 	pfvf->nix_blkaddr = BLKADDR_NIX0;
-	if (p2x == CMR_P2X_SEL_NIX1)
+	if (is_rvu_supports_nix1(rvu) && p2x == CMR_P2X_SEL_NIX1)
 		pfvf->nix_blkaddr = BLKADDR_NIX1;
 }
 
@@ -411,7 +411,7 @@
  * VF's of mapped PF and other PFs are not allowed. This fn() checks
  * whether a PFFUNC is permitted to do the config or not.
  */
-static bool is_cgx_config_permitted(struct rvu *rvu, u16 pcifunc)
+inline bool is_cgx_config_permitted(struct rvu *rvu, u16 pcifunc)
 {
 	if ((pcifunc & RVU_PFVF_FUNC_MASK) ||
 	    !is_pf_cgxmapped(rvu, rvu_get_pf(pcifunc)))
@@ -442,16 +442,43 @@
 int rvu_cgx_config_rxtx(struct rvu *rvu, u16 pcifunc, bool start)
 {
 	int pf = rvu_get_pf(pcifunc);
+	struct mac_ops *mac_ops;
 	u8 cgx_id, lmac_id;
+	void *cgxd;
 
 	if (!is_cgx_config_permitted(rvu, pcifunc))
 		return LMAC_AF_ERR_PERM_DENIED;
 
 	rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
+	cgxd = rvu_cgx_pdata(cgx_id, rvu);
+	mac_ops = get_mac_ops(cgxd);
 
-	cgx_lmac_rx_tx_enable(rvu_cgx_pdata(cgx_id, rvu), lmac_id, start);
+	return mac_ops->mac_rx_tx_enable(cgxd, lmac_id, start);
+}
 
-	return 0;
+int rvu_cgx_tx_enable(struct rvu *rvu, u16 pcifunc, bool enable)
+{
+	int pf = rvu_get_pf(pcifunc);
+	struct mac_ops *mac_ops;
+	u8 cgx_id, lmac_id;
+	void *cgxd;
+
+	if (!is_cgx_config_permitted(rvu, pcifunc))
+		return LMAC_AF_ERR_PERM_DENIED;
+
+	rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
+	cgxd = rvu_cgx_pdata(cgx_id, rvu);
+	mac_ops = get_mac_ops(cgxd);
+
+	return mac_ops->mac_tx_enable(cgxd, lmac_id, enable);
+}
+
+int rvu_cgx_config_tx(void *cgxd, int lmac_id, bool enable)
+{
+	struct mac_ops *mac_ops;
+
+	mac_ops = get_mac_ops(cgxd);
+	return mac_ops->mac_tx_enable(cgxd, lmac_id, enable);
 }
 
 void rvu_cgx_disable_dmac_entries(struct rvu *rvu, u16 pcifunc)
@@ -694,7 +721,9 @@
 
 static int rvu_cgx_ptp_rx_cfg(struct rvu *rvu, u16 pcifunc, bool enable)
 {
+	struct rvu_pfvf *pfvf = rvu_get_pfvf(rvu, pcifunc);
 	int pf = rvu_get_pf(pcifunc);
+	struct mac_ops *mac_ops;
 	u8 cgx_id, lmac_id;
 	void *cgxd;
 
@@ -711,13 +740,16 @@
 	rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
 	cgxd = rvu_cgx_pdata(cgx_id, rvu);
 
-	cgx_lmac_ptp_config(cgxd, lmac_id, enable);
+	mac_ops = get_mac_ops(cgxd);
+	mac_ops->mac_enadis_ptp_config(cgxd, lmac_id, enable);
 	/* If PTP is enabled then inform NPC that packets to be
 	 * parsed by this PF will have their data shifted by 8 bytes
 	 * and if PTP is disabled then no shift is required
 	 */
 	if (npc_config_ts_kpuaction(rvu, pf, pcifunc, enable))
 		return -EINVAL;
+	/* This flag is required to clean up CGX conf if app gets killed */
+	pfvf->hw_rx_tstamp_en = enable;
 
 	return 0;
 }
@@ -816,6 +848,22 @@
 	return fifo_len;
 }
 
+u32 rvu_cgx_get_lmac_fifolen(struct rvu *rvu, int cgx, int lmac)
+{
+	struct mac_ops *mac_ops;
+	void *cgxd;
+
+	cgxd = rvu_cgx_pdata(cgx, rvu);
+	if (!cgxd)
+		return 0;
+
+	mac_ops = get_mac_ops(cgxd);
+	if (!mac_ops->lmac_fifo_len)
+		return 0;
+
+	return mac_ops->lmac_fifo_len(cgxd, lmac);
+}
+
 static int rvu_cgx_config_intlbk(struct rvu *rvu, u16 pcifunc, bool en)
 {
 	int pf = rvu_get_pf(pcifunc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_cn10k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_cn10k.c
@@ -60,13 +60,14 @@
 			   u64 iova, u64 *lmt_addr)
 {
 	u64 pa, val, pf;
-	int err;
+	int err = 0;
 
 	if (!iova) {
 		dev_err(rvu->dev, "%s Requested Null address for transulation\n", __func__);
 		return -EINVAL;
 	}
 
+	mutex_lock(&rvu->rsrc_lock);
 	rvu_write64(rvu, BLKADDR_RVUM, RVU_AF_SMMU_ADDR_REQ, iova);
 	pf = rvu_get_pf(pcifunc) & 0x1F;
 	val = BIT_ULL(63) | BIT_ULL(14) | BIT_ULL(13) | pf << 8 |
@@ -76,12 +77,13 @@
 	err = rvu_poll_reg(rvu, BLKADDR_RVUM, RVU_AF_SMMU_ADDR_RSP_STS, BIT_ULL(0), false);
 	if (err) {
 		dev_err(rvu->dev, "%s LMTLINE iova transulation failed\n", __func__);
-		return err;
+		goto exit;
 	}
 	val = rvu_read64(rvu, BLKADDR_RVUM, RVU_AF_SMMU_ADDR_RSP_STS);
 	if (val & ~0x1ULL) {
 		dev_err(rvu->dev, "%s LMTLINE iova transulation failed err:%llx\n", __func__, val);
-		return -EIO;
+		err = -EIO;
+		goto exit;
 	}
 	/* PA[51:12] = RVU_AF_SMMU_TLN_FLIT0[57:18]
 	 * PA[11:0] = IOVA[11:0]
@@ -89,8 +91,9 @@
 	pa = rvu_read64(rvu, BLKADDR_RVUM, RVU_AF_SMMU_TLN_FLIT0) >> 18;
 	pa &= GENMASK_ULL(39, 0);
 	*lmt_addr = (pa << 12) | (iova  & 0xFFF);
-
-	return 0;
+exit:
+	mutex_unlock(&rvu->rsrc_lock);
+	return err;
 }
 
 static int rvu_update_lmtaddr(struct rvu *rvu, u16 pcifunc, u64 lmt_addr)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_cpt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_cpt.c
@@ -17,7 +17,7 @@
 #define	PCI_DEVID_OTX2_CPT10K_PF 0xA0F2
 
 /* Length of initial context fetch in 128 byte words */
-#define CPT_CTX_ILEN    2
+#define CPT_CTX_ILEN    1ULL
 
 #define cpt_get_eng_sts(e_min, e_max, rsp, etype)                   \
 ({                                                                  \
@@ -142,8 +142,12 @@
 
 		/* Set CPT LF group and priority */
 		val = (u64)req->eng_grpmsk << 48 | 1;
-		if (!is_rvu_otx2(rvu))
-			val |= (CPT_CTX_ILEN << 17);
+		if (!is_rvu_otx2(rvu)) {
+			if (req->ctx_ilen_valid)
+				val |= (req->ctx_ilen << 17);
+			else
+				val |= (CPT_CTX_ILEN << 17);
+		}
 
 		rvu_write64(rvu, blkaddr, CPT_AF_LFX_CTL(cptlf), val);
 
@@ -206,7 +210,7 @@
 
 	blkaddr = validate_and_get_cpt_blkaddr(req->blkaddr);
 	if (blkaddr < 0)
-		return blkaddr;
+		return false;
 
 	/* Registers that can be accessed from PF/VF */
 	if ((offset & 0xFF000) ==  CPT_AF_LFX_CTL(0) ||
@@ -260,7 +264,8 @@
 					struct cpt_rd_wr_reg_msg *req,
 					struct cpt_rd_wr_reg_msg *rsp)
 {
-	int blkaddr;
+	u64 offset = req->reg_offset;
+	int blkaddr, lf;
 
 	blkaddr = validate_and_get_cpt_blkaddr(req->blkaddr);
 	if (blkaddr < 0)
@@ -271,17 +276,25 @@
 	    !is_cpt_vf(rvu, req->hdr.pcifunc))
 		return CPT_AF_ERR_ACCESS_DENIED;
 
-	rsp->reg_offset = req->reg_offset;
-	rsp->ret_val = req->ret_val;
-	rsp->is_write = req->is_write;
-
 	if (!is_valid_offset(rvu, req))
 		return CPT_AF_ERR_ACCESS_DENIED;
 
+	/* Translate local LF used by VFs to global CPT LF */
+	lf = rvu_get_lf(rvu, &rvu->hw->block[blkaddr], req->hdr.pcifunc,
+			(offset & 0xFFF) >> 3);
+
+	/* Translate local LF's offset to global CPT LF's offset */
+	offset &= 0xFF000;
+	offset += lf << 3;
+
+	rsp->reg_offset = offset;
+	rsp->ret_val = req->ret_val;
+	rsp->is_write = req->is_write;
+
 	if (req->is_write)
-		rvu_write64(rvu, blkaddr, req->reg_offset, req->val);
+		rvu_write64(rvu, blkaddr, offset, req->val);
 	else
-		rsp->val = rvu_read64(rvu, blkaddr, req->reg_offset);
+		rsp->val = rvu_read64(rvu, blkaddr, offset);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.c
@@ -196,9 +196,6 @@
 	CPT_IE_TYPE = 3,
 };
 
-#define NDC_MAX_BANK(rvu, blk_addr) (rvu_read64(rvu, \
-						blk_addr, NDC_AF_CONST) & 0xFF)
-
 #define rvu_dbg_NULL NULL
 #define rvu_dbg_open_NULL NULL
 
@@ -441,6 +438,8 @@
 		sprintf(lmac, "LMAC%d", lmac_id);
 		seq_printf(filp, "%s\t0x%x\t\tNIX%d\t\t%s\t%s\n",
 			   dev_name(&pdev->dev), pcifunc, blkid, cgx, lmac);
+
+		pci_dev_put(pdev);
 	}
 	return 0;
 }
@@ -560,12 +559,10 @@
 	u16 pcifunc;
 	int ret, lf;
 
-	cmd_buf = memdup_user(buffer, count + 1);
+	cmd_buf = memdup_user_nul(buffer, count);
 	if (IS_ERR(cmd_buf))
 		return -ENOMEM;
 
-	cmd_buf[count] = '\0';
-
 	cmd_buf_tmp = strchr(cmd_buf, '\n');
 	if (cmd_buf_tmp) {
 		*cmd_buf_tmp = '\0';
@@ -1007,6 +1004,7 @@
 	struct nix_hw *nix_hw;
 	struct rvu *rvu;
 	int bank, max_bank;
+	u64 ndc_af_const;
 
 	if (blk_addr == BLKADDR_NDC_NPA0) {
 		rvu = s->private;
@@ -1015,7 +1013,8 @@
 		rvu = nix_hw->rvu;
 	}
 
-	max_bank = NDC_MAX_BANK(rvu, blk_addr);
+	ndc_af_const = rvu_read64(rvu, blk_addr, NDC_AF_CONST);
+	max_bank = FIELD_GET(NDC_AF_BANK_MASK, ndc_af_const);
 	for (bank = 0; bank < max_bank; bank++) {
 		seq_printf(s, "BANK:%d\n", bank);
 		seq_printf(s, "\tHits:\t%lld\n",
@@ -1131,6 +1130,8 @@
 	seq_printf(m, "W3: head_offset\t\t\t%d\nW3: smenq_next_sqb_vld\t\t%d\n\n",
 		   sq_ctx->head_offset, sq_ctx->smenq_next_sqb_vld);
 
+	seq_printf(m, "W3: smq_next_sq_vld\t\t%d\nW3: smq_pend\t\t\t%d\n",
+		   sq_ctx->smq_next_sq_vld, sq_ctx->smq_pend);
 	seq_printf(m, "W4: next_sqb \t\t\t%llx\n\n", sq_ctx->next_sqb);
 	seq_printf(m, "W5: tail_sqb \t\t\t%llx\n\n", sq_ctx->tail_sqb);
 	seq_printf(m, "W6: smenq_sqb \t\t\t%llx\n\n", sq_ctx->smenq_sqb);
@@ -2125,6 +2126,7 @@
 		}
 	}
 
+	pci_dev_put(pdev);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_devlink.c
@@ -216,7 +216,7 @@
 		rvu->irq_allocated[offs + NIX_AF_INT_VEC_RVU] = false;
 	}
 
-	for (i = NIX_AF_INT_VEC_AF_ERR; i < NIX_AF_INT_VEC_CNT; i++)
+	for (i = NIX_AF_INT_VEC_GEN; i < NIX_AF_INT_VEC_CNT; i++)
 		if (rvu->irq_allocated[offs + i]) {
 			free_irq(pci_irq_vector(rvu->pdev, offs + i), rvu_dl);
 			rvu->irq_allocated[offs + i] = false;
@@ -641,7 +641,7 @@
 
 	rvu_dl->devlink_wq = create_workqueue("rvu_devlink_wq");
 	if (!rvu_dl->devlink_wq)
-		goto err;
+		return -ENOMEM;
 
 	INIT_WORK(&rvu_reporters->intr_work, rvu_nix_intr_work);
 	INIT_WORK(&rvu_reporters->gen_work, rvu_nix_gen_work);
@@ -649,9 +649,6 @@
 	INIT_WORK(&rvu_reporters->ras_work, rvu_nix_ras_work);
 
 	return 0;
-err:
-	rvu_nix_health_reporters_destroy(rvu_dl);
-	return -ENOMEM;
 }
 
 static int rvu_nix_health_reporters_create(struct rvu_devlink *rvu_dl)
@@ -1284,7 +1281,7 @@
 
 	rvu_dl->devlink_wq = create_workqueue("rvu_devlink_wq");
 	if (!rvu_dl->devlink_wq)
-		goto err;
+		return -ENOMEM;
 
 	INIT_WORK(&rvu_reporters->intr_work, rvu_npa_intr_work);
 	INIT_WORK(&rvu_reporters->err_work, rvu_npa_err_work);
@@ -1292,9 +1289,6 @@
 	INIT_WORK(&rvu_reporters->ras_work, rvu_npa_ras_work);
 
 	return 0;
-err:
-	rvu_npa_health_reporters_destroy(rvu_dl);
-	return -ENOMEM;
 }
 
 static int rvu_npa_health_reporters_create(struct rvu_devlink *rvu_dl)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c
@@ -28,6 +28,7 @@
 static int nix_free_all_bandprof(struct rvu *rvu, u16 pcifunc);
 static void nix_clear_ratelimit_aggr(struct rvu *rvu, struct nix_hw *nix_hw,
 				     u32 leaf_prof);
+static const char *nix_get_ctx_name(int ctype);
 
 enum mc_tbl_sz {
 	MC_TBL_SZ_256,
@@ -295,7 +296,6 @@
 	struct rvu_hwinfo *hw = rvu->hw;
 	struct sdp_node_info *sdp_info;
 	int pkind, pf, vf, lbkid, vfid;
-	struct mac_ops *mac_ops;
 	u8 cgx_id, lmac_id;
 	bool from_vf;
 	int err;
@@ -325,13 +325,6 @@
 		cgx_set_pkind(rvu_cgx_pdata(cgx_id, rvu), lmac_id, pkind);
 		rvu_npc_set_pkind(rvu, pkind, pfvf);
 
-		mac_ops = get_mac_ops(rvu_cgx_pdata(cgx_id, rvu));
-
-		/* By default we enable pause frames */
-		if ((pcifunc & RVU_PFVF_FUNC_MASK) == 0)
-			mac_ops->mac_enadis_pause_frm(rvu_cgx_pdata(cgx_id,
-								    rvu),
-						      lmac_id, true, true);
 		break;
 	case NIX_INTF_TYPE_LBK:
 		vf = (pcifunc & RVU_PFVF_FUNC_MASK) - 1;
@@ -511,11 +504,11 @@
 	cfg = rvu_read64(rvu, blkaddr, NIX_AF_CONST);
 	lmac_chan_cnt = cfg & 0xFF;
 
-	cfg = rvu_read64(rvu, blkaddr, NIX_AF_CONST1);
-	sdp_chan_cnt = cfg & 0xFFF;
-
 	cgx_bpid_cnt = hw->cgx_links * lmac_chan_cnt;
 	lbk_bpid_cnt = hw->lbk_links * ((cfg >> 16) & 0xFF);
+
+	cfg = rvu_read64(rvu, blkaddr, NIX_AF_CONST1);
+	sdp_chan_cnt = cfg & 0xFFF;
 	sdp_bpid_cnt = hw->sdp_links * sdp_chan_cnt;
 
 	pfvf = rvu_get_pfvf(rvu, req->hdr.pcifunc);
@@ -796,6 +789,7 @@
 	struct nix_aq_res_s *result;
 	int timeout = 1000;
 	u64 reg, head;
+	int ret;
 
 	result = (struct nix_aq_res_s *)aq->res->base;
 
@@ -819,13 +813,41 @@
 			return -EBUSY;
 	}
 
-	if (result->compcode != NIX_AQ_COMP_GOOD)
+	if (result->compcode != NIX_AQ_COMP_GOOD) {
 		/* TODO: Replace this with some error code */
+		if (result->compcode == NIX_AQ_COMP_CTX_FAULT ||
+		    result->compcode == NIX_AQ_COMP_LOCKERR ||
+		    result->compcode == NIX_AQ_COMP_CTX_POISON) {
+			ret = rvu_ndc_fix_locked_cacheline(rvu, BLKADDR_NDC_NIX0_RX);
+			ret |= rvu_ndc_fix_locked_cacheline(rvu, BLKADDR_NDC_NIX0_TX);
+			ret |= rvu_ndc_fix_locked_cacheline(rvu, BLKADDR_NDC_NIX1_RX);
+			ret |= rvu_ndc_fix_locked_cacheline(rvu, BLKADDR_NDC_NIX1_TX);
+			if (ret)
+				dev_err(rvu->dev,
+					"%s: Not able to unlock cachelines\n", __func__);
+		}
+
 		return -EBUSY;
+	}
 
 	return 0;
 }
 
+static void nix_get_aq_req_smq(struct rvu *rvu, struct nix_aq_enq_req *req,
+			       u16 *smq, u16 *smq_mask)
+{
+	struct nix_cn10k_aq_enq_req *aq_req;
+
+	if (!is_rvu_otx2(rvu)) {
+		aq_req = (struct nix_cn10k_aq_enq_req *)req;
+		*smq = aq_req->sq.smq;
+		*smq_mask = aq_req->sq_mask.smq;
+	} else {
+		*smq = req->sq.smq;
+		*smq_mask = req->sq_mask.smq;
+	}
+}
+
 static int rvu_nix_blk_aq_enq_inst(struct rvu *rvu, struct nix_hw *nix_hw,
 				   struct nix_aq_enq_req *req,
 				   struct nix_aq_enq_rsp *rsp)
@@ -837,6 +859,7 @@
 	struct rvu_block *block;
 	struct admin_queue *aq;
 	struct rvu_pfvf *pfvf;
+	u16 smq, smq_mask;
 	void *ctx, *mask;
 	bool ena;
 	u64 cfg;
@@ -908,13 +931,14 @@
 	if (rc)
 		return rc;
 
+	nix_get_aq_req_smq(rvu, req, &smq, &smq_mask);
 	/* Check if SQ pointed SMQ belongs to this PF/VF or not */
 	if (req->ctype == NIX_AQ_CTYPE_SQ &&
 	    ((req->op == NIX_AQ_INSTOP_INIT && req->sq.ena) ||
 	     (req->op == NIX_AQ_INSTOP_WRITE &&
-	      req->sq_mask.ena && req->sq_mask.smq && req->sq.ena))) {
+	      req->sq_mask.ena && req->sq.ena && smq_mask))) {
 		if (!is_valid_txschq(rvu, blkaddr, NIX_TXSCH_LVL_SMQ,
-				     pcifunc, req->sq.smq))
+				     pcifunc, smq))
 			return NIX_AF_ERR_AQ_ENQUEUE;
 	}
 
@@ -1061,10 +1085,68 @@
 	return 0;
 }
 
+static int rvu_nix_verify_aq_ctx(struct rvu *rvu, struct nix_hw *nix_hw,
+				 struct nix_aq_enq_req *req, u8 ctype)
+{
+	struct nix_cn10k_aq_enq_req aq_req;
+	struct nix_cn10k_aq_enq_rsp aq_rsp;
+	int rc, word;
+
+	if (req->ctype != NIX_AQ_CTYPE_CQ)
+		return 0;
+
+	rc = nix_aq_context_read(rvu, nix_hw, &aq_req, &aq_rsp,
+				 req->hdr.pcifunc, ctype, req->qidx);
+	if (rc) {
+		dev_err(rvu->dev,
+			"%s: Failed to fetch %s%d context of PFFUNC 0x%x\n",
+			__func__, nix_get_ctx_name(ctype), req->qidx,
+			req->hdr.pcifunc);
+		return rc;
+	}
+
+	/* Make copy of original context & mask which are required
+	 * for resubmission
+	 */
+	memcpy(&aq_req.cq_mask, &req->cq_mask, sizeof(struct nix_cq_ctx_s));
+	memcpy(&aq_req.cq, &req->cq, sizeof(struct nix_cq_ctx_s));
+
+	/* exclude fields which HW can update */
+	aq_req.cq_mask.cq_err       = 0;
+	aq_req.cq_mask.wrptr        = 0;
+	aq_req.cq_mask.tail         = 0;
+	aq_req.cq_mask.head	    = 0;
+	aq_req.cq_mask.avg_level    = 0;
+	aq_req.cq_mask.update_time  = 0;
+	aq_req.cq_mask.substream    = 0;
+
+	/* Context mask (cq_mask) holds mask value of fields which
+	 * are changed in AQ WRITE operation.
+	 * for example cq.drop = 0xa;
+	 *	       cq_mask.drop = 0xff;
+	 * Below logic performs '&' between cq and cq_mask so that non
+	 * updated fields are masked out for request and response
+	 * comparison
+	 */
+	for (word = 0; word < sizeof(struct nix_cq_ctx_s) / sizeof(u64);
+	     word++) {
+		*(u64 *)((u8 *)&aq_rsp.cq + word * 8) &=
+			(*(u64 *)((u8 *)&aq_req.cq_mask + word * 8));
+		*(u64 *)((u8 *)&aq_req.cq + word * 8) &=
+			(*(u64 *)((u8 *)&aq_req.cq_mask + word * 8));
+	}
+
+	if (memcmp(&aq_req.cq, &aq_rsp.cq, sizeof(struct nix_cq_ctx_s)))
+		return NIX_AF_ERR_AQ_CTX_RETRY_WRITE;
+
+	return 0;
+}
+
 static int rvu_nix_aq_enq_inst(struct rvu *rvu, struct nix_aq_enq_req *req,
 			       struct nix_aq_enq_rsp *rsp)
 {
 	struct nix_hw *nix_hw;
+	int err, retries = 5;
 	int blkaddr;
 
 	blkaddr = rvu_get_blkaddr(rvu, BLKTYPE_NIX, req->hdr.pcifunc);
@@ -1075,7 +1157,24 @@
 	if (!nix_hw)
 		return NIX_AF_ERR_INVALID_NIXBLK;
 
-	return rvu_nix_blk_aq_enq_inst(rvu, nix_hw, req, rsp);
+retry:
+	err = rvu_nix_blk_aq_enq_inst(rvu, nix_hw, req, rsp);
+
+	/* HW errata 'AQ Modification to CQ could be discarded on heavy traffic'
+	 * As a work around perfrom CQ context read after each AQ write. If AQ
+	 * read shows AQ write is not updated perform AQ write again.
+	 */
+	if (!err && req->op == NIX_AQ_INSTOP_WRITE) {
+		err = rvu_nix_verify_aq_ctx(rvu, nix_hw, req, NIX_AQ_CTYPE_CQ);
+		if (err == NIX_AF_ERR_AQ_CTX_RETRY_WRITE) {
+			if (retries--)
+				goto retry;
+			else
+				return NIX_AF_ERR_CQ_CTX_WRITE_ERR;
+		}
+	}
+
+	return err;
 }
 
 static const char *nix_get_ctx_name(int ctype)
@@ -1795,7 +1894,8 @@
 		free_cnt = rvu_rsrc_free_count(&txsch->schq);
 	}
 
-	if (free_cnt < req_schq || req_schq > MAX_TXSCHQ_PER_FUNC)
+	if (free_cnt < req_schq || req->schq[lvl] > MAX_TXSCHQ_PER_FUNC ||
+	    req->schq_contig[lvl] > MAX_TXSCHQ_PER_FUNC)
 		return NIX_AF_ERR_TLX_ALLOC_FAIL;
 
 	/* If contiguous queues are needed, check for availability */
@@ -1981,42 +2081,203 @@
 	return rc;
 }
 
+static void nix_smq_flush_fill_ctx(struct rvu *rvu, int blkaddr, int smq,
+				   struct nix_smq_flush_ctx *smq_flush_ctx)
+{
+	struct nix_smq_tree_ctx *smq_tree_ctx;
+	u64 parent_off, regval;
+	u16 schq;
+	int lvl;
+
+	smq_flush_ctx->smq = smq;
+
+	schq = smq;
+	for (lvl = NIX_TXSCH_LVL_SMQ; lvl <= NIX_TXSCH_LVL_TL1; lvl++) {
+		smq_tree_ctx = &smq_flush_ctx->smq_tree_ctx[lvl];
+		smq_tree_ctx->schq = schq;
+		if (lvl == NIX_TXSCH_LVL_TL1) {
+			smq_tree_ctx->cir_off = NIX_AF_TL1X_CIR(schq);
+			smq_tree_ctx->pir_off = 0;
+			smq_tree_ctx->pir_val = 0;
+			parent_off = 0;
+		} else if (lvl == NIX_TXSCH_LVL_TL2) {
+			smq_tree_ctx->cir_off = NIX_AF_TL2X_CIR(schq);
+			smq_tree_ctx->pir_off = NIX_AF_TL2X_PIR(schq);
+			parent_off = NIX_AF_TL2X_PARENT(schq);
+		} else if (lvl == NIX_TXSCH_LVL_TL3) {
+			smq_tree_ctx->cir_off = NIX_AF_TL3X_CIR(schq);
+			smq_tree_ctx->pir_off = NIX_AF_TL3X_PIR(schq);
+			parent_off = NIX_AF_TL3X_PARENT(schq);
+		} else if (lvl == NIX_TXSCH_LVL_TL4) {
+			smq_tree_ctx->cir_off = NIX_AF_TL4X_CIR(schq);
+			smq_tree_ctx->pir_off = NIX_AF_TL4X_PIR(schq);
+			parent_off = NIX_AF_TL4X_PARENT(schq);
+		} else if (lvl == NIX_TXSCH_LVL_MDQ) {
+			smq_tree_ctx->cir_off = NIX_AF_MDQX_CIR(schq);
+			smq_tree_ctx->pir_off = NIX_AF_MDQX_PIR(schq);
+			parent_off = NIX_AF_MDQX_PARENT(schq);
+		}
+		/* save cir/pir register values */
+		smq_tree_ctx->cir_val = rvu_read64(rvu, blkaddr, smq_tree_ctx->cir_off);
+		if (smq_tree_ctx->pir_off)
+			smq_tree_ctx->pir_val = rvu_read64(rvu, blkaddr, smq_tree_ctx->pir_off);
+
+		/* get parent txsch node */
+		if (parent_off) {
+			regval = rvu_read64(rvu, blkaddr, parent_off);
+			schq = (regval >> 16) & 0x1FF;
+		}
+	}
+}
+
+static void nix_smq_flush_enadis_xoff(struct rvu *rvu, int blkaddr,
+				      struct nix_smq_flush_ctx *smq_flush_ctx, bool enable)
+{
+	struct nix_txsch *txsch;
+	struct nix_hw *nix_hw;
+	int tl2, tl2_schq;
+	u64 regoff;
+
+	nix_hw = get_nix_hw(rvu->hw, blkaddr);
+	if (!nix_hw)
+		return;
+
+	/* loop through all TL2s with matching PF_FUNC */
+	txsch = &nix_hw->txsch[NIX_TXSCH_LVL_TL2];
+	tl2_schq = smq_flush_ctx->smq_tree_ctx[NIX_TXSCH_LVL_TL2].schq;
+	for (tl2 = 0; tl2 < txsch->schq.max; tl2++) {
+		/* skip the smq(flush) TL2 */
+		if (tl2 == tl2_schq)
+			continue;
+		/* skip unused TL2s */
+		if (TXSCH_MAP_FLAGS(txsch->pfvf_map[tl2]) & NIX_TXSCHQ_FREE)
+			continue;
+		/* skip if PF_FUNC doesn't match */
+		if ((TXSCH_MAP_FUNC(txsch->pfvf_map[tl2]) & ~RVU_PFVF_FUNC_MASK) !=
+		    (TXSCH_MAP_FUNC(txsch->pfvf_map[tl2_schq] &
+				    ~RVU_PFVF_FUNC_MASK)))
+			continue;
+		/* enable/disable XOFF */
+		regoff = NIX_AF_TL2X_SW_XOFF(tl2);
+		if (enable)
+			rvu_write64(rvu, blkaddr, regoff, 0x1);
+		else
+			rvu_write64(rvu, blkaddr, regoff, 0x0);
+	}
+}
+
+static void nix_smq_flush_enadis_rate(struct rvu *rvu, int blkaddr,
+				      struct nix_smq_flush_ctx *smq_flush_ctx, bool enable)
+{
+	u64 cir_off, pir_off, cir_val, pir_val;
+	struct nix_smq_tree_ctx *smq_tree_ctx;
+	int lvl;
+
+	for (lvl = NIX_TXSCH_LVL_SMQ; lvl <= NIX_TXSCH_LVL_TL1; lvl++) {
+		smq_tree_ctx = &smq_flush_ctx->smq_tree_ctx[lvl];
+		cir_off = smq_tree_ctx->cir_off;
+		cir_val = smq_tree_ctx->cir_val;
+		pir_off = smq_tree_ctx->pir_off;
+		pir_val = smq_tree_ctx->pir_val;
+
+		if (enable) {
+			rvu_write64(rvu, blkaddr, cir_off, cir_val);
+			if (lvl != NIX_TXSCH_LVL_TL1)
+				rvu_write64(rvu, blkaddr, pir_off, pir_val);
+		} else {
+			rvu_write64(rvu, blkaddr, cir_off, 0x0);
+			if (lvl != NIX_TXSCH_LVL_TL1)
+				rvu_write64(rvu, blkaddr, pir_off, 0x0);
+		}
+	}
+}
+
 static int nix_smq_flush(struct rvu *rvu, int blkaddr,
 			 int smq, u16 pcifunc, int nixlf)
 {
+	struct nix_smq_flush_ctx *smq_flush_ctx;
+	int err, restore_tx_en = 0, i;
 	int pf = rvu_get_pf(pcifunc);
 	u8 cgx_id = 0, lmac_id = 0;
-	int err, restore_tx_en = 0;
-	u64 cfg;
+	u16 tl2_tl3_link_schq;
+	u8 link, link_level;
+	u64 cfg, bmap = 0;
 
 	/* enable cgx tx if disabled */
 	if (is_pf_cgxmapped(rvu, pf)) {
 		rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
-		restore_tx_en = !cgx_lmac_tx_enable(rvu_cgx_pdata(cgx_id, rvu),
-						    lmac_id, true);
+		restore_tx_en = !rvu_cgx_config_tx(rvu_cgx_pdata(cgx_id, rvu),
+						   lmac_id, true);
 	}
 
-	cfg = rvu_read64(rvu, blkaddr, NIX_AF_SMQX_CFG(smq));
-	/* Do SMQ flush and set enqueue xoff */
-	cfg |= BIT_ULL(50) | BIT_ULL(49);
-	rvu_write64(rvu, blkaddr, NIX_AF_SMQX_CFG(smq), cfg);
+	/* XOFF all TL2s whose parent TL1 matches SMQ tree TL1 */
+	smq_flush_ctx = kzalloc(sizeof(*smq_flush_ctx), GFP_KERNEL);
+	if (!smq_flush_ctx)
+		return -ENOMEM;
+	nix_smq_flush_fill_ctx(rvu, blkaddr, smq, smq_flush_ctx);
+	nix_smq_flush_enadis_xoff(rvu, blkaddr, smq_flush_ctx, true);
+	nix_smq_flush_enadis_rate(rvu, blkaddr, smq_flush_ctx, false);
 
 	/* Disable backpressure from physical link,
 	 * otherwise SMQ flush may stall.
 	 */
 	rvu_cgx_enadis_rx_bp(rvu, pf, false);
 
+	link_level = rvu_read64(rvu, blkaddr, NIX_AF_PSE_CHANNEL_LEVEL) & 0x01 ?
+			NIX_TXSCH_LVL_TL3 : NIX_TXSCH_LVL_TL2;
+	tl2_tl3_link_schq = smq_flush_ctx->smq_tree_ctx[link_level].schq;
+	link = smq_flush_ctx->smq_tree_ctx[NIX_TXSCH_LVL_TL1].schq;
+
+	/* SMQ set enqueue xoff */
+	cfg = rvu_read64(rvu, blkaddr, NIX_AF_SMQX_CFG(smq));
+	cfg |= BIT_ULL(50);
+	rvu_write64(rvu, blkaddr, NIX_AF_SMQX_CFG(smq), cfg);
+
+	/* Clear all NIX_AF_TL3_TL2_LINK_CFG[ENA] for the TL3/TL2 queue */
+	for (i = 0; i < (rvu->hw->cgx_links + rvu->hw->lbk_links); i++) {
+		cfg = rvu_read64(rvu, blkaddr,
+				 NIX_AF_TL3_TL2X_LINKX_CFG(tl2_tl3_link_schq, link));
+		if (!(cfg & BIT_ULL(12)))
+			continue;
+		bmap |= BIT_ULL(i);
+		cfg &= ~BIT_ULL(12);
+		rvu_write64(rvu, blkaddr,
+			    NIX_AF_TL3_TL2X_LINKX_CFG(tl2_tl3_link_schq, link), cfg);
+	}
+
+	/* Do SMQ flush and set enqueue xoff */
+	cfg = rvu_read64(rvu, blkaddr, NIX_AF_SMQX_CFG(smq));
+	cfg |= BIT_ULL(50) | BIT_ULL(49);
+	rvu_write64(rvu, blkaddr, NIX_AF_SMQX_CFG(smq), cfg);
+
 	/* Wait for flush to complete */
 	err = rvu_poll_reg(rvu, blkaddr,
 			   NIX_AF_SMQX_CFG(smq), BIT_ULL(49), true);
 	if (err)
-		dev_err(rvu->dev,
-			"NIXLF%d: SMQ%d flush failed\n", nixlf, smq);
+		dev_info(rvu->dev,
+			 "NIXLF%d: SMQ%d flush failed, txlink might be busy\n",
+			 nixlf, smq);
+
+	/* Set NIX_AF_TL3_TL2_LINKX_CFG[ENA] for the TL3/TL2 queue */
+	for (i = 0; i < (rvu->hw->cgx_links + rvu->hw->lbk_links); i++) {
+		if (!(bmap & BIT_ULL(i)))
+			continue;
+		cfg = rvu_read64(rvu, blkaddr,
+				 NIX_AF_TL3_TL2X_LINKX_CFG(tl2_tl3_link_schq, link));
+		cfg |= BIT_ULL(12);
+		rvu_write64(rvu, blkaddr,
+			    NIX_AF_TL3_TL2X_LINKX_CFG(tl2_tl3_link_schq, link), cfg);
+	}
+
+	/* clear XOFF on TL2s */
+	nix_smq_flush_enadis_rate(rvu, blkaddr, smq_flush_ctx, true);
+	nix_smq_flush_enadis_xoff(rvu, blkaddr, smq_flush_ctx, false);
+	kfree(smq_flush_ctx);
 
 	rvu_cgx_enadis_rx_bp(rvu, pf, true);
 	/* restore cgx tx state */
 	if (restore_tx_en)
-		cgx_lmac_tx_enable(rvu_cgx_pdata(cgx_id, rvu), lmac_id, false);
+		rvu_cgx_config_tx(rvu_cgx_pdata(cgx_id, rvu), lmac_id, false);
 	return err;
 }
 
@@ -3207,6 +3468,11 @@
 	return -ERANGE;
 }
 
+/* Mask to match ipv6(NPC_LT_LC_IP6) and ipv6 ext(NPC_LT_LC_IP6_EXT) */
+#define NPC_LT_LC_IP6_MATCH_MSK ((~(NPC_LT_LC_IP6 ^ NPC_LT_LC_IP6_EXT)) & 0xf)
+/* Mask to match both ipv4(NPC_LT_LC_IP) and ipv4 ext(NPC_LT_LC_IP_OPT) */
+#define NPC_LT_LC_IP_MATCH_MSK  ((~(NPC_LT_LC_IP ^ NPC_LT_LC_IP_OPT)) & 0xf)
+
 static int set_flowkey_fields(struct nix_rx_flowkey_alg *alg, u32 flow_cfg)
 {
 	int idx, nr_field, key_off, field_marker, keyoff_marker;
@@ -3214,6 +3480,7 @@
 	struct nix_rx_flowkey_alg *field;
 	struct nix_rx_flowkey_alg tmp;
 	u32 key_type, valid_key;
+	u32 l3_l4_src_dst;
 	int l4_key_offset = 0;
 
 	if (!alg)
@@ -3241,6 +3508,15 @@
 	 * group_member - Enabled when protocol is part of a group.
 	 */
 
+	/* Last 4 bits (31:28) are reserved to specify SRC, DST
+	 * selection for L3, L4 i.e IPV[4,6]_SRC, IPV[4,6]_DST,
+	 * [TCP,UDP,SCTP]_SRC, [TCP,UDP,SCTP]_DST
+	 * 31 => L3_SRC, 30 => L3_DST, 29 => L4_SRC, 28 => L4_DST
+	 */
+	l3_l4_src_dst = flow_cfg;
+	/* Reset these 4 bits, so that these won't be part of key */
+	flow_cfg &= NIX_FLOW_KEY_TYPE_L3_L4_MASK;
+
 	keyoff_marker = 0; max_key_off = 0; group_member = 0;
 	nr_field = 0; key_off = 0; field_marker = 1;
 	field = &tmp; max_bit_pos = fls(flow_cfg);
@@ -3266,7 +3542,7 @@
 			field->hdr_offset = 9; /* offset */
 			field->bytesm1 = 0; /* 1 byte */
 			field->ltype_match = NPC_LT_LC_IP;
-			field->ltype_mask = 0xF;
+			field->ltype_mask = NPC_LT_LC_IP_MATCH_MSK;
 			break;
 		case NIX_FLOW_KEY_TYPE_IPV4:
 		case NIX_FLOW_KEY_TYPE_INNR_IPV4:
@@ -3278,7 +3554,22 @@
 			}
 			field->hdr_offset = 12; /* SIP offset */
 			field->bytesm1 = 7; /* SIP + DIP, 8 bytes */
-			field->ltype_mask = 0xF; /* Match only IPv4 */
+
+			/* Only SIP */
+			if (l3_l4_src_dst & NIX_FLOW_KEY_TYPE_L3_SRC_ONLY)
+				field->bytesm1 = 3; /* SIP, 4 bytes */
+
+			if (l3_l4_src_dst & NIX_FLOW_KEY_TYPE_L3_DST_ONLY) {
+				/* Both SIP + DIP */
+				if (field->bytesm1 == 3) {
+					field->bytesm1 = 7; /* SIP + DIP, 8B */
+				} else {
+					/* Only DIP */
+					field->hdr_offset = 16; /* DIP off */
+					field->bytesm1 = 3; /* DIP, 4 bytes */
+				}
+			}
+			field->ltype_mask = NPC_LT_LC_IP_MATCH_MSK;
 			keyoff_marker = false;
 			break;
 		case NIX_FLOW_KEY_TYPE_IPV6:
@@ -3291,7 +3582,23 @@
 			}
 			field->hdr_offset = 8; /* SIP offset */
 			field->bytesm1 = 31; /* SIP + DIP, 32 bytes */
-			field->ltype_mask = 0xF; /* Match only IPv6 */
+
+			/* Only SIP */
+			if (l3_l4_src_dst & NIX_FLOW_KEY_TYPE_L3_SRC_ONLY)
+				field->bytesm1 = 15; /* SIP, 16 bytes */
+
+			if (l3_l4_src_dst & NIX_FLOW_KEY_TYPE_L3_DST_ONLY) {
+				/* Both SIP + DIP */
+				if (field->bytesm1 == 15) {
+					/* SIP + DIP, 32 bytes */
+					field->bytesm1 = 31;
+				} else {
+					/* Only DIP */
+					field->hdr_offset = 24; /* DIP off */
+					field->bytesm1 = 15; /* DIP,16 bytes */
+				}
+			}
+			field->ltype_mask = NPC_LT_LC_IP6_MATCH_MSK;
 			break;
 		case NIX_FLOW_KEY_TYPE_TCP:
 		case NIX_FLOW_KEY_TYPE_UDP:
@@ -3306,6 +3613,21 @@
 				field->lid = NPC_LID_LH;
 			field->bytesm1 = 3; /* Sport + Dport, 4 bytes */
 
+			if (l3_l4_src_dst & NIX_FLOW_KEY_TYPE_L4_SRC_ONLY)
+				field->bytesm1 = 1; /* SRC, 2 bytes */
+
+			if (l3_l4_src_dst & NIX_FLOW_KEY_TYPE_L4_DST_ONLY) {
+				/* Both SRC + DST */
+				if (field->bytesm1 == 1) {
+					/* SRC + DST, 4 bytes */
+					field->bytesm1 = 3;
+				} else {
+					/* Only DIP */
+					field->hdr_offset = 2; /* DST off */
+					field->bytesm1 = 1; /* DST, 2 bytes */
+				}
+			}
+
 			/* Enum values for NPC_LID_LD and NPC_LID_LG are same,
 			 * so no need to change the ltype_match, just change
 			 * the lid for inner protocols
@@ -3777,90 +4099,18 @@
 		req->minlen = minlen;
 }
 
-static int
-nix_config_link_credits(struct rvu *rvu, int blkaddr, int link,
-			u16 pcifunc, u64 tx_credits)
-{
-	struct rvu_hwinfo *hw = rvu->hw;
-	int pf = rvu_get_pf(pcifunc);
-	u8 cgx_id = 0, lmac_id = 0;
-	unsigned long poll_tmo;
-	bool restore_tx_en = 0;
-	struct nix_hw *nix_hw;
-	u64 cfg, sw_xoff = 0;
-	u32 schq = 0;
-	u32 credits;
-	int rc;
-
-	nix_hw = get_nix_hw(rvu->hw, blkaddr);
-	if (!nix_hw)
-		return NIX_AF_ERR_INVALID_NIXBLK;
-
-	if (tx_credits == nix_hw->tx_credits[link])
-		return 0;
-
-	/* Enable cgx tx if disabled for credits to be back */
-	if (is_pf_cgxmapped(rvu, pf)) {
-		rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
-		restore_tx_en = !cgx_lmac_tx_enable(rvu_cgx_pdata(cgx_id, rvu),
-						    lmac_id, true);
-	}
-
-	mutex_lock(&rvu->rsrc_lock);
-	/* Disable new traffic to link */
-	if (hw->cap.nix_shaping) {
-		schq = nix_get_tx_link(rvu, pcifunc);
-		sw_xoff = rvu_read64(rvu, blkaddr, NIX_AF_TL1X_SW_XOFF(schq));
-		rvu_write64(rvu, blkaddr,
-			    NIX_AF_TL1X_SW_XOFF(schq), BIT_ULL(0));
-	}
-
-	rc = -EBUSY;
-	poll_tmo = jiffies + usecs_to_jiffies(10000);
-	/* Wait for credits to return */
-	do {
-		if (time_after(jiffies, poll_tmo))
-			goto exit;
-		usleep_range(100, 200);
-
-		cfg = rvu_read64(rvu, blkaddr,
-				 NIX_AF_TX_LINKX_NORM_CREDIT(link));
-		credits = (cfg >> 12) & 0xFFFFFULL;
-	} while (credits != nix_hw->tx_credits[link]);
-
-	cfg &= ~(0xFFFFFULL << 12);
-	cfg |= (tx_credits << 12);
-	rvu_write64(rvu, blkaddr, NIX_AF_TX_LINKX_NORM_CREDIT(link), cfg);
-	rc = 0;
-
-	nix_hw->tx_credits[link] = tx_credits;
-
-exit:
-	/* Enable traffic back */
-	if (hw->cap.nix_shaping && !sw_xoff)
-		rvu_write64(rvu, blkaddr, NIX_AF_TL1X_SW_XOFF(schq), 0);
-
-	/* Restore state of cgx tx */
-	if (restore_tx_en)
-		cgx_lmac_tx_enable(rvu_cgx_pdata(cgx_id, rvu), lmac_id, false);
-
-	mutex_unlock(&rvu->rsrc_lock);
-	return rc;
-}
-
 int rvu_mbox_handler_nix_set_hw_frs(struct rvu *rvu, struct nix_frs_cfg *req,
 				    struct msg_rsp *rsp)
 {
 	struct rvu_hwinfo *hw = rvu->hw;
 	u16 pcifunc = req->hdr.pcifunc;
 	int pf = rvu_get_pf(pcifunc);
-	int blkaddr, schq, link = -1;
-	struct nix_txsch *txsch;
-	u64 cfg, lmac_fifo_len;
+	int blkaddr, link = -1;
 	struct nix_hw *nix_hw;
 	struct rvu_pfvf *pfvf;
 	u8 cgx = 0, lmac = 0;
 	u16 max_mtu;
+	u64 cfg;
 
 	blkaddr = rvu_get_blkaddr(rvu, BLKTYPE_NIX, pcifunc);
 	if (blkaddr < 0)
@@ -3881,25 +4131,6 @@
 	if (req->update_minlen && req->minlen < NIC_HW_MIN_FRS)
 		return NIX_AF_ERR_FRS_INVALID;
 
-	/* Check if requester wants to update SMQ's */
-	if (!req->update_smq)
-		goto rx_frscfg;
-
-	/* Update min/maxlen in each of the SMQ attached to this PF/VF */
-	txsch = &nix_hw->txsch[NIX_TXSCH_LVL_SMQ];
-	mutex_lock(&rvu->rsrc_lock);
-	for (schq = 0; schq < txsch->schq.max; schq++) {
-		if (TXSCH_MAP_FUNC(txsch->pfvf_map[schq]) != pcifunc)
-			continue;
-		cfg = rvu_read64(rvu, blkaddr, NIX_AF_SMQX_CFG(schq));
-		cfg = (cfg & ~(0xFFFFULL << 8)) | ((u64)req->maxlen << 8);
-		if (req->update_minlen)
-			cfg = (cfg & ~0x7FULL) | ((u64)req->minlen & 0x7F);
-		rvu_write64(rvu, blkaddr, NIX_AF_SMQX_CFG(schq), cfg);
-	}
-	mutex_unlock(&rvu->rsrc_lock);
-
-rx_frscfg:
 	/* Check if config is for SDP link */
 	if (req->sdp_link) {
 		if (!hw->sdp_links)
@@ -3922,24 +4153,16 @@
 	if (link < 0)
 		return NIX_AF_ERR_RX_LINK_INVALID;
 
+linkcfg:
 	nix_find_link_frs(rvu, req, pcifunc);
 
-linkcfg:
 	cfg = rvu_read64(rvu, blkaddr, NIX_AF_RX_LINKX_CFG(link));
 	cfg = (cfg & ~(0xFFFFULL << 16)) | ((u64)req->maxlen << 16);
 	if (req->update_minlen)
 		cfg = (cfg & ~0xFFFFULL) | req->minlen;
 	rvu_write64(rvu, blkaddr, NIX_AF_RX_LINKX_CFG(link), cfg);
 
-	if (req->sdp_link || pf == 0)
-		return 0;
-
-	/* Update transmit credits for CGX links */
-	lmac_fifo_len =
-		rvu_cgx_get_fifolen(rvu) /
-		cgx_get_lmac_cnt(rvu_cgx_pdata(cgx, rvu));
-	return nix_config_link_credits(rvu, blkaddr, link, pcifunc,
-				       (lmac_fifo_len - req->maxlen) / 16);
+	return 0;
 }
 
 int rvu_mbox_handler_nix_set_rx_cfg(struct rvu *rvu, struct nix_rx_cfg *req,
@@ -3976,10 +4199,6 @@
 
 static u64 rvu_get_lbk_link_credits(struct rvu *rvu, u16 lbk_max_frs)
 {
-	/* CN10k supports 72KB FIFO size and max packet size of 64k */
-	if (rvu->hw->lbk_bufsize == 0x12000)
-		return (rvu->hw->lbk_bufsize - lbk_max_frs) / 16;
-
 	return 1600; /* 16 * max LBK datarate = 16 * 100Gbps */
 }
 
@@ -3989,7 +4208,10 @@
 	struct rvu_hwinfo *hw = rvu->hw;
 	int cgx, lmac_cnt, slink, link;
 	u16 lbk_max_frs, lmac_max_frs;
+	unsigned long lmac_bmap;
 	u64 tx_credits, cfg;
+	u64 lmac_fifo_len;
+	int iter;
 
 	rvu_get_lbk_link_max_frs(rvu, &lbk_max_frs);
 	rvu_get_lmac_link_max_frs(rvu, &lmac_max_frs);
@@ -4023,12 +4245,23 @@
 		/* Skip when cgx is not available or lmac cnt is zero */
 		if (lmac_cnt <= 0)
 			continue;
-		tx_credits = ((rvu_cgx_get_fifolen(rvu) / lmac_cnt) -
-			       lmac_max_frs) / 16;
-		/* Enable credits and set credit pkt count to max allowed */
-		cfg =  (tx_credits << 12) | (0x1FF << 2) | BIT_ULL(1);
 		slink = cgx * hw->lmac_per_cgx;
-		for (link = slink; link < (slink + lmac_cnt); link++) {
+
+		/* Get LMAC id's from bitmap */
+		lmac_bmap = cgx_get_lmac_bmap(rvu_cgx_pdata(cgx, rvu));
+		for_each_set_bit(iter, &lmac_bmap, MAX_LMAC_PER_CGX) {
+			lmac_fifo_len = rvu_cgx_get_lmac_fifolen(rvu, cgx, iter);
+			if (!lmac_fifo_len) {
+				dev_err(rvu->dev,
+					"%s: Failed to get CGX/RPM%d:LMAC%d FIFO size\n",
+					__func__, cgx, iter);
+				continue;
+			}
+			tx_credits = (lmac_fifo_len - lmac_max_frs) / 16;
+			/* Enable credits and set credit pkt count to max allowed */
+			cfg =  (tx_credits << 12) | (0x1FF << 2) | BIT_ULL(1);
+
+			link = iter + slink;
 			nix_hw->tx_credits[link] = tx_credits;
 			rvu_write64(rvu, blkaddr,
 				    NIX_AF_TX_LINKX_NORM_CREDIT(link), cfg);
@@ -4173,18 +4406,18 @@
 		 */
 		rvu_write64(rvu, blkaddr, NIX_AF_CFG,
 			    rvu_read64(rvu, blkaddr, NIX_AF_CFG) | 0x40ULL);
+	}
 
-		/* Set chan/link to backpressure TL3 instead of TL2 */
-		rvu_write64(rvu, blkaddr, NIX_AF_PSE_CHANNEL_LEVEL, 0x01);
+	/* Set chan/link to backpressure TL3 instead of TL2 */
+	rvu_write64(rvu, blkaddr, NIX_AF_PSE_CHANNEL_LEVEL, 0x01);
 
-		/* Disable SQ manager's sticky mode operation (set TM6 = 0)
-		 * This sticky mode is known to cause SQ stalls when multiple
-		 * SQs are mapped to same SMQ and transmitting pkts at a time.
-		 */
-		cfg = rvu_read64(rvu, blkaddr, NIX_AF_SQM_DBG_CTL_STATUS);
-		cfg &= ~BIT_ULL(15);
-		rvu_write64(rvu, blkaddr, NIX_AF_SQM_DBG_CTL_STATUS, cfg);
-	}
+	/* Disable SQ manager's sticky mode operation (set TM6 = 0)
+	 * This sticky mode is known to cause SQ stalls when multiple
+	 * SQs are mapped to same SMQ and transmitting pkts at a time.
+	 */
+	cfg = rvu_read64(rvu, blkaddr, NIX_AF_SQM_DBG_CTL_STATUS);
+	cfg &= ~BIT_ULL(15);
+	rvu_write64(rvu, blkaddr, NIX_AF_SQM_DBG_CTL_STATUS, cfg);
 
 	ltdefs = rvu->kpu.lt_def;
 	/* Calibrate X2P bus to check if CGX/LBK links are fine */
@@ -4436,13 +4669,23 @@
 	pfvf = rvu_get_pfvf(rvu, pcifunc);
 	clear_bit(NIXLF_INITIALIZED, &pfvf->flags);
 
-	return rvu_cgx_start_stop_io(rvu, pcifunc, false);
+	err = rvu_cgx_start_stop_io(rvu, pcifunc, false);
+	if (err)
+		return err;
+
+	rvu_cgx_tx_enable(rvu, pcifunc, true);
+
+	return 0;
 }
 
 void rvu_nix_lf_teardown(struct rvu *rvu, u16 pcifunc, int blkaddr, int nixlf)
 {
 	struct rvu_pfvf *pfvf = rvu_get_pfvf(rvu, pcifunc);
 	struct hwctx_disable_req ctx_req;
+	int pf = rvu_get_pf(pcifunc);
+	struct mac_ops *mac_ops;
+	u8 cgx_id, lmac_id;
+	void *cgxd;
 	int err;
 
 	ctx_req.hdr.pcifunc = pcifunc;
@@ -4479,6 +4722,22 @@
 			dev_err(rvu->dev, "CQ ctx disable failed\n");
 	}
 
+	/* reset HW config done for Switch headers */
+	rvu_npc_set_parse_mode(rvu, pcifunc, OTX2_PRIV_FLAGS_DEFAULT,
+			       (PKIND_TX | PKIND_RX), 0, 0, 0, 0);
+
+	/* Disabling CGX and NPC config done for PTP */
+	if (pfvf->hw_rx_tstamp_en) {
+		rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
+		cgxd = rvu_cgx_pdata(cgx_id, rvu);
+		mac_ops = get_mac_ops(cgxd);
+		mac_ops->mac_enadis_ptp_config(cgxd, lmac_id, false);
+		/* Undo NPC config done for PTP */
+		if (npc_config_ts_kpuaction(rvu, pf, pcifunc, false))
+			dev_err(rvu->dev, "NPC config for PTP failed\n");
+		pfvf->hw_rx_tstamp_en = false;
+	}
+
 	nix_ctx_free(rvu, pfvf);
 
 	nix_free_all_bandprof(rvu, pcifunc);
@@ -4736,6 +4995,8 @@
 		ipolicer->ref_count = devm_kcalloc(rvu->dev,
 						   ipolicer->band_prof.max,
 						   sizeof(u16), GFP_KERNEL);
+		if (!ipolicer->ref_count)
+			return -ENOMEM;
 	}
 
 	/* Set policer timeunit to 2us ie  (19 + 1) * 100 nsec = 2us */
@@ -4918,6 +5179,8 @@
 
 		ipolicer = &nix_hw->ipolicer[layer];
 		for (idx = 0; idx < req->prof_count[layer]; idx++) {
+			if (idx == MAX_BANDPROF_PER_PFFUNC)
+				break;
 			prof_idx = req->prof_idx[layer][idx];
 			if (prof_idx >= ipolicer->band_prof.max ||
 			    ipolicer->pfvf_map[prof_idx] != pcifunc)
@@ -4931,8 +5194,6 @@
 			ipolicer->pfvf_map[prof_idx] = 0x00;
 			ipolicer->match_id[prof_idx] = 0;
 			rvu_free_rsrc(&ipolicer->band_prof, prof_idx);
-			if (idx == MAX_BANDPROF_PER_PFFUNC)
-				break;
 		}
 	}
 	mutex_unlock(&rvu->rsrc_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c
@@ -4,7 +4,7 @@
  * Copyright (C) 2018 Marvell.
  *
  */
-
+#include <linux/bitfield.h>
 #include <linux/module.h>
 #include <linux/pci.h>
 
@@ -42,9 +42,18 @@
 			return -EBUSY;
 	}
 
-	if (result->compcode != NPA_AQ_COMP_GOOD)
+	if (result->compcode != NPA_AQ_COMP_GOOD) {
 		/* TODO: Replace this with some error code */
+		if (result->compcode == NPA_AQ_COMP_CTX_FAULT ||
+		    result->compcode == NPA_AQ_COMP_LOCKERR ||
+		    result->compcode == NPA_AQ_COMP_CTX_POISON) {
+			if (rvu_ndc_fix_locked_cacheline(rvu, BLKADDR_NDC_NPA0))
+				dev_err(rvu->dev,
+					"%s: Not able to unlock cachelines\n", __func__);
+		}
+
 		return -EBUSY;
+	}
 
 	return 0;
 }
@@ -545,3 +554,48 @@
 
 	npa_ctx_free(rvu, pfvf);
 }
+
+/* Due to an Hardware errata, in some corner cases, AQ context lock
+ * operations can result in a NDC way getting into an illegal state
+ * of not valid but locked.
+ *
+ * This API solves the problem by clearing the lock bit of the NDC block.
+ * The operation needs to be done for each line of all the NDC banks.
+ */
+int rvu_ndc_fix_locked_cacheline(struct rvu *rvu, int blkaddr)
+{
+	int bank, max_bank, line, max_line, err;
+	u64 reg, ndc_af_const;
+
+	/* Set the ENABLE bit(63) to '0' */
+	reg = rvu_read64(rvu, blkaddr, NDC_AF_CAMS_RD_INTERVAL);
+	rvu_write64(rvu, blkaddr, NDC_AF_CAMS_RD_INTERVAL, reg & GENMASK_ULL(62, 0));
+
+	/* Poll until the BUSY bits(47:32) are set to '0' */
+	err = rvu_poll_reg(rvu, blkaddr, NDC_AF_CAMS_RD_INTERVAL, GENMASK_ULL(47, 32), true);
+	if (err) {
+		dev_err(rvu->dev, "Timed out while polling for NDC CAM busy bits.\n");
+		return err;
+	}
+
+	ndc_af_const = rvu_read64(rvu, blkaddr, NDC_AF_CONST);
+	max_bank = FIELD_GET(NDC_AF_BANK_MASK, ndc_af_const);
+	max_line = FIELD_GET(NDC_AF_BANK_LINE_MASK, ndc_af_const);
+	for (bank = 0; bank < max_bank; bank++) {
+		for (line = 0; line < max_line; line++) {
+			/* Check if 'cache line valid bit(63)' is not set
+			 * but 'cache line lock bit(60)' is set and on
+			 * success, reset the lock bit(60).
+			 */
+			reg = rvu_read64(rvu, blkaddr,
+					 NDC_AF_BANKX_LINEX_METADATA(bank, line));
+			if (!(reg & BIT_ULL(63)) && (reg & BIT_ULL(60))) {
+				rvu_write64(rvu, blkaddr,
+					    NDC_AF_BANKX_LINEX_METADATA(bank, line),
+					    reg & ~BIT_ULL(60));
+			}
+		}
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c
@@ -388,7 +388,13 @@
 	int bank, nixlf, index;
 
 	/* get ucast entry rule entry index */
-	nix_get_nixlf(rvu, pf_func, &nixlf, NULL);
+	if (nix_get_nixlf(rvu, pf_func, &nixlf, NULL)) {
+		dev_err(rvu->dev, "%s: nixlf not attached to pcifunc:0x%x\n",
+			__func__, pf_func);
+		/* Action 0 is drop */
+		return 0;
+	}
+
 	index = npc_get_nixlf_mcam_index(mcam, pf_func, nixlf,
 					 NIXLF_UCAST_ENTRY);
 	bank = npc_get_bank(mcam, index);
@@ -402,6 +408,7 @@
 			      int blkaddr, int index, struct mcam_entry *entry,
 			      bool *enable)
 {
+	struct rvu_npc_mcam_rule *rule;
 	u16 owner, target_func;
 	struct rvu_pfvf *pfvf;
 	u64 rx_action;
@@ -423,6 +430,16 @@
 	      test_bit(NIXLF_INITIALIZED, &pfvf->flags)))
 		*enable = false;
 
+	/* fix up not needed for the rules added by user(ntuple filters) */
+	list_for_each_entry(rule, &mcam->mcam_rules, list) {
+		if (rule->entry == index)
+			return;
+	}
+
+	/* AF modifies given action iff PF/VF has requested for it */
+	if ((entry->action & 0xFULL) != NIX_RX_ACTION_DEFAULT)
+		return;
+
 	/* copy VF default entry action to the VF mcam entry */
 	rx_action = npc_get_default_entry_action(rvu, mcam, blkaddr,
 						 target_func);
@@ -489,8 +506,8 @@
 	}
 
 	/* PF installing VF rule */
-	if (intf == NIX_INTF_RX && actindex < mcam->bmap_entries)
-		npc_fixup_vf_rule(rvu, mcam, blkaddr, index, entry, &enable);
+	if (is_npc_intf_rx(intf) && actindex < mcam->bmap_entries)
+		npc_fixup_vf_rule(rvu, mcam, blkaddr, actindex, entry, &enable);
 
 	/* Set 'action' */
 	rvu_write64(rvu, blkaddr,
@@ -598,7 +615,7 @@
 	struct npc_install_flow_req req = { 0 };
 	struct npc_install_flow_rsp rsp = { 0 };
 	struct npc_mcam *mcam = &rvu->hw->mcam;
-	struct nix_rx_action action;
+	struct nix_rx_action action = { 0 };
 	int blkaddr, index;
 
 	/* AF's and SDP VFs work in promiscuous mode */
@@ -619,7 +636,6 @@
 		*(u64 *)&action = npc_get_mcam_action(rvu, mcam,
 						      blkaddr, index);
 	} else {
-		*(u64 *)&action = 0x00;
 		action.op = NIX_RX_ACTIONOP_UCAST;
 		action.pf_func = pcifunc;
 	}
@@ -650,8 +666,9 @@
 	struct npc_mcam *mcam = &rvu->hw->mcam;
 	struct rvu_hwinfo *hw = rvu->hw;
 	int blkaddr, ucast_idx, index;
-	struct nix_rx_action action;
+	struct nix_rx_action action = { 0 };
 	u64 relaxed_mask;
+	u8 flow_key_alg;
 
 	if (!hw->cap.nix_rx_multicast && is_cgx_vf(rvu, pcifunc))
 		return;
@@ -678,14 +695,16 @@
 						      blkaddr, ucast_idx);
 
 	if (action.op != NIX_RX_ACTIONOP_RSS) {
-		*(u64 *)&action = 0x00;
+		*(u64 *)&action = 0;
 		action.op = NIX_RX_ACTIONOP_UCAST;
 	}
 
+	flow_key_alg = action.flow_key_alg;
+
 	/* RX_ACTION set to MCAST for CGX PF's */
 	if (hw->cap.nix_rx_multicast && pfvf->use_mce_list &&
 	    is_pf_cgxmapped(rvu, rvu_get_pf(pcifunc))) {
-		*(u64 *)&action = 0x00;
+		*(u64 *)&action = 0;
 		action.op = NIX_RX_ACTIONOP_MCAST;
 		pfvf = rvu_get_pfvf(rvu, pcifunc & ~RVU_PFVF_FUNC_MASK);
 		action.index = pfvf->promisc_mce_idx;
@@ -721,7 +740,7 @@
 	req.vf = pcifunc;
 	req.index = action.index;
 	req.match_id = action.match_id;
-	req.flow_key_alg = action.flow_key_alg;
+	req.flow_key_alg = flow_key_alg;
 
 	rvu_mbox_handler_npc_install_flow(rvu, &req, &rsp);
 }
@@ -825,8 +844,9 @@
 	struct rvu_hwinfo *hw = rvu->hw;
 	int blkaddr, ucast_idx, index;
 	u8 mac_addr[ETH_ALEN] = { 0 };
-	struct nix_rx_action action;
+	struct nix_rx_action action = { 0 };
 	struct rvu_pfvf *pfvf;
+	u8 flow_key_alg;
 	u16 vf_func;
 
 	/* Only CGX PF/VF can add allmulticast entry */
@@ -853,15 +873,16 @@
 		*(u64 *)&action = npc_get_mcam_action(rvu, mcam,
 							blkaddr, ucast_idx);
 
+	flow_key_alg = action.flow_key_alg;
 	if (action.op != NIX_RX_ACTIONOP_RSS) {
-		*(u64 *)&action = 0x00;
+		*(u64 *)&action = 0;
 		action.op = NIX_RX_ACTIONOP_UCAST;
 		action.pf_func = pcifunc;
 	}
 
 	/* RX_ACTION set to MCAST for CGX PF's */
 	if (hw->cap.nix_rx_multicast && pfvf->use_mce_list) {
-		*(u64 *)&action = 0x00;
+		*(u64 *)&action = 0;
 		action.op = NIX_RX_ACTIONOP_MCAST;
 		action.index = pfvf->mcast_mce_idx;
 	}
@@ -889,7 +910,7 @@
 	req.vf = pcifunc | vf_func;
 	req.index = action.index;
 	req.match_id = action.match_id;
-	req.flow_key_alg = action.flow_key_alg;
+	req.flow_key_alg = flow_key_alg;
 
 	rvu_mbox_handler_npc_install_flow(rvu, &req, &rsp);
 }
@@ -916,7 +937,8 @@
 				     int blkaddr, u16 pcifunc, u64 rx_action)
 {
 	int actindex, index, bank, entry;
-	bool enable;
+	struct rvu_npc_mcam_rule *rule;
+	bool enable, update;
 
 	if (!(pcifunc & RVU_PFVF_FUNC_MASK))
 		return;
@@ -924,6 +946,14 @@
 	mutex_lock(&mcam->lock);
 	for (index = 0; index < mcam->bmap_entries; index++) {
 		if (mcam->entry2target_pffunc[index] == pcifunc) {
+			update = true;
+			/* update not needed for the rules added via ntuple filters */
+			list_for_each_entry(rule, &mcam->mcam_rules, list) {
+				if (rule->entry == index)
+					update = false;
+			}
+			if (!update)
+				continue;
 			bank = npc_get_bank(mcam, index);
 			actindex = index;
 			entry = index & (mcam->banksize - 1);
@@ -946,11 +976,38 @@
 	mutex_unlock(&mcam->lock);
 }
 
+static void npc_update_rx_action_with_alg_idx(struct rvu *rvu, struct nix_rx_action action,
+					      struct rvu_pfvf *pfvf, int mcam_index, int blkaddr,
+					      int alg_idx)
+
+{
+	struct npc_mcam *mcam = &rvu->hw->mcam;
+	struct rvu_hwinfo *hw = rvu->hw;
+	int bank, op_rss;
+
+	if (!is_mcam_entry_enabled(rvu, mcam, blkaddr, mcam_index))
+		return;
+
+	op_rss = (!hw->cap.nix_rx_multicast || !pfvf->use_mce_list);
+
+	bank = npc_get_bank(mcam, mcam_index);
+	mcam_index &= (mcam->banksize - 1);
+
+	/* If Rx action is MCAST update only RSS algorithm index */
+	if (!op_rss) {
+		*(u64 *)&action = rvu_read64(rvu, blkaddr,
+				NPC_AF_MCAMEX_BANKX_ACTION(mcam_index, bank));
+
+		action.flow_key_alg = alg_idx;
+	}
+	rvu_write64(rvu, blkaddr,
+		    NPC_AF_MCAMEX_BANKX_ACTION(mcam_index, bank), *(u64 *)&action);
+}
+
 void rvu_npc_update_flowkey_alg_idx(struct rvu *rvu, u16 pcifunc, int nixlf,
 				    int group, int alg_idx, int mcam_index)
 {
 	struct npc_mcam *mcam = &rvu->hw->mcam;
-	struct rvu_hwinfo *hw = rvu->hw;
 	struct nix_rx_action action;
 	int blkaddr, index, bank;
 	struct rvu_pfvf *pfvf;
@@ -1006,15 +1063,16 @@
 	/* If PF's promiscuous entry is enabled,
 	 * Set RSS action for that entry as well
 	 */
-	if ((!hw->cap.nix_rx_multicast || !pfvf->use_mce_list) &&
-	    is_mcam_entry_enabled(rvu, mcam, blkaddr, index)) {
-		bank = npc_get_bank(mcam, index);
-		index &= (mcam->banksize - 1);
+	npc_update_rx_action_with_alg_idx(rvu, action, pfvf, index, blkaddr,
+					  alg_idx);
 
-		rvu_write64(rvu, blkaddr,
-			    NPC_AF_MCAMEX_BANKX_ACTION(index, bank),
-			    *(u64 *)&action);
-	}
+	index = npc_get_nixlf_mcam_index(mcam, pcifunc,
+					 nixlf, NIXLF_ALLMULTI_ENTRY);
+	/* If PF's allmulti  entry is enabled,
+	 * Set RSS action for that entry as well
+	 */
+	npc_update_rx_action_with_alg_idx(rvu, action, pfvf, index, blkaddr,
+					  alg_idx);
 }
 
 void npc_enadis_default_mce_entry(struct rvu *rvu, u16 pcifunc,
@@ -1081,6 +1139,9 @@
 
 void rvu_npc_disable_default_entries(struct rvu *rvu, u16 pcifunc, int nixlf)
 {
+	if (nixlf < 0)
+		return;
+
 	npc_enadis_default_entries(rvu, pcifunc, nixlf, false);
 
 	/* Delete multicast and promisc MCAM entries */
@@ -1092,6 +1153,9 @@
 
 void rvu_npc_enable_default_entries(struct rvu *rvu, u16 pcifunc, int nixlf)
 {
+	if (nixlf < 0)
+		return;
+
 	/* Enables only broadcast match entry. Promisc/Allmulti are enabled
 	 * in set_rx_mode mbox handler.
 	 */
@@ -1558,7 +1622,7 @@
 	struct npc_coalesced_kpu_prfl *img_data = NULL;
 	int i = 0, rc = -EINVAL;
 	void __iomem *kpu_prfl_addr;
-	u16 offset;
+	u32 offset;
 
 	img_data = (struct npc_coalesced_kpu_prfl __force *)rvu->kpu_prfl_addr;
 	if (le64_to_cpu(img_data->signature) == KPU_SIGN &&
@@ -1635,7 +1699,7 @@
 	 * Firmware database method.
 	 * Default KPU profile.
 	 */
-	if (!request_firmware(&fw, kpu_profile, rvu->dev)) {
+	if (!request_firmware_direct(&fw, kpu_profile, rvu->dev)) {
 		dev_info(rvu->dev, "Loading KPU profile from firmware: %s\n",
 			 kpu_profile);
 		rvu->kpu_fwdata = kzalloc(fw->size, GFP_KERNEL);
@@ -1900,6 +1964,7 @@
 
 static void rvu_npc_setup_interfaces(struct rvu *rvu, int blkaddr)
 {
+	struct npc_mcam_kex *mkex = rvu->kpu.mkex;
 	struct npc_mcam *mcam = &rvu->hw->mcam;
 	struct rvu_hwinfo *hw = rvu->hw;
 	u64 nibble_ena, rx_kex, tx_kex;
@@ -1912,15 +1977,15 @@
 	mcam->counters.max--;
 	mcam->rx_miss_act_cntr = mcam->counters.max;
 
-	rx_kex = npc_mkex_default.keyx_cfg[NIX_INTF_RX];
-	tx_kex = npc_mkex_default.keyx_cfg[NIX_INTF_TX];
+	rx_kex = mkex->keyx_cfg[NIX_INTF_RX];
+	tx_kex = mkex->keyx_cfg[NIX_INTF_TX];
 	nibble_ena = FIELD_GET(NPC_PARSE_NIBBLE, rx_kex);
 
 	nibble_ena = rvu_npc_get_tx_nibble_cfg(rvu, nibble_ena);
 	if (nibble_ena) {
 		tx_kex &= ~NPC_PARSE_NIBBLE;
 		tx_kex |= FIELD_PREP(NPC_PARSE_NIBBLE, nibble_ena);
-		npc_mkex_default.keyx_cfg[NIX_INTF_TX] = tx_kex;
+		mkex->keyx_cfg[NIX_INTF_TX] = tx_kex;
 	}
 
 	/* Configure RX interfaces */
@@ -2394,7 +2459,17 @@
 	 * - when available free entries are less.
 	 * Lower priority ones out of avaialble free entries are always
 	 * chosen when 'high vs low' question arises.
+	 *
+	 * For a VF base MCAM match rule is set by its PF. And all the
+	 * further MCAM rules installed by VF on its own are
+	 * concatenated with the base rule set by its PF. Hence PF entries
+	 * should be at lower priority compared to VF entries. Otherwise
+	 * base rule is hit always and rules installed by VF will be of
+	 * no use. Hence if the request is from PF then allocate low
+	 * priority entries.
 	 */
+	if (!(pcifunc & RVU_PFVF_FUNC_MASK))
+		goto lprio_alloc;
 
 	/* Get the search range for priority allocation request */
 	if (req->priority) {
@@ -2403,17 +2478,6 @@
 		goto alloc;
 	}
 
-	/* For a VF base MCAM match rule is set by its PF. And all the
-	 * further MCAM rules installed by VF on its own are
-	 * concatenated with the base rule set by its PF. Hence PF entries
-	 * should be at lower priority compared to VF entries. Otherwise
-	 * base rule is hit always and rules installed by VF will be of
-	 * no use. Hence if the request is from PF and NOT a priority
-	 * allocation request then allocate low priority entries.
-	 */
-	if (!(pcifunc & RVU_PFVF_FUNC_MASK))
-		goto lprio_alloc;
-
 	/* Find out the search range for non-priority allocation request
 	 *
 	 * Get MCAM free entry count in middle zone.
@@ -2443,6 +2507,18 @@
 		reverse = true;
 		start = 0;
 		end = mcam->bmap_entries;
+		/* Ensure PF requests are always at bottom and if PF requests
+		 * for higher/lower priority entry wrt reference entry then
+		 * honour that criteria and start search for entries from bottom
+		 * and not in mid zone.
+		 */
+		if (!(pcifunc & RVU_PFVF_FUNC_MASK) &&
+		    req->priority == NPC_MCAM_HIGHER_PRIO)
+			end = req->ref_entry;
+
+		if (!(pcifunc & RVU_PFVF_FUNC_MASK) &&
+		    req->priority == NPC_MCAM_LOWER_PRIO)
+			start = req->ref_entry;
 	}
 
 alloc:
@@ -2564,18 +2640,17 @@
 	rsp->entry = NPC_MCAM_ENTRY_INVALID;
 	rsp->free_count = 0;
 
-	/* Check if ref_entry is within range */
-	if (req->priority && req->ref_entry >= mcam->bmap_entries) {
-		dev_err(rvu->dev, "%s: reference entry %d is out of range\n",
-			__func__, req->ref_entry);
-		return NPC_MCAM_INVALID_REQ;
-	}
+	/* Check if ref_entry is greater that the range
+	 * then set it to max value.
+	 */
+	if (req->ref_entry > mcam->bmap_entries)
+		req->ref_entry = mcam->bmap_entries;
 
 	/* ref_entry can't be '0' if requested priority is high.
 	 * Can't be last entry if requested priority is low.
 	 */
 	if ((!req->ref_entry && req->priority == NPC_MCAM_HIGHER_PRIO) ||
-	    ((req->ref_entry == (mcam->bmap_entries - 1)) &&
+	    ((req->ref_entry == mcam->bmap_entries) &&
 	     req->priority == NPC_MCAM_LOWER_PRIO))
 		return NPC_MCAM_INVALID_REQ;
 
@@ -3167,6 +3242,102 @@
 	return 0;
 }
 
+static int
+npc_set_var_len_offset_pkind(struct rvu *rvu, u16 pcifunc, u64 pkind,
+			     u8 var_len_off, u8 var_len_off_mask, u8 shift_dir)
+{
+	struct npc_kpu_action0 *act0;
+	u8 shift_count = 0;
+	int blkaddr;
+	u64 val;
+
+	if (!var_len_off_mask)
+		return -EINVAL;
+
+	if (var_len_off_mask != 0xff) {
+		if (shift_dir)
+			shift_count = __ffs(var_len_off_mask);
+		else
+			shift_count = (8 - __fls(var_len_off_mask));
+	}
+	blkaddr = rvu_get_blkaddr(rvu, BLKTYPE_NPC, pcifunc);
+	if (blkaddr < 0) {
+		dev_err(rvu->dev, "%s: NPC block not implemented\n", __func__);
+		return -EINVAL;
+	}
+	val = rvu_read64(rvu, blkaddr, NPC_AF_PKINDX_ACTION0(pkind));
+	act0 = (struct npc_kpu_action0 *)&val;
+	act0->var_len_shift = shift_count;
+	act0->var_len_right = shift_dir;
+	act0->var_len_mask = var_len_off_mask;
+	act0->var_len_offset = var_len_off;
+	rvu_write64(rvu, blkaddr, NPC_AF_PKINDX_ACTION0(pkind), val);
+	return 0;
+}
+
+int rvu_npc_set_parse_mode(struct rvu *rvu, u16 pcifunc, u64 mode, u8 dir,
+			   u64 pkind, u8 var_len_off, u8 var_len_off_mask,
+			   u8 shift_dir)
+
+{
+	struct rvu_pfvf *pfvf = rvu_get_pfvf(rvu, pcifunc);
+	int blkaddr, nixlf, rc, intf_mode;
+	int pf = rvu_get_pf(pcifunc);
+	u64 rxpkind, txpkind;
+	u8 cgx_id, lmac_id;
+
+	/* use default pkind to disable edsa/higig */
+	rxpkind = rvu_npc_get_pkind(rvu, pf);
+	txpkind = NPC_TX_DEF_PKIND;
+	intf_mode = NPC_INTF_MODE_DEF;
+
+	if (mode & OTX2_PRIV_FLAGS_CUSTOM) {
+		if (pkind == NPC_RX_CUSTOM_PRE_L2_PKIND) {
+			rc = npc_set_var_len_offset_pkind(rvu, pcifunc, pkind,
+							  var_len_off,
+							  var_len_off_mask,
+							  shift_dir);
+			if (rc)
+				return rc;
+		}
+		rxpkind = pkind;
+		txpkind = pkind;
+	}
+
+	if (dir & PKIND_RX) {
+		/* rx pkind set req valid only for cgx mapped PFs */
+		if (!is_cgx_config_permitted(rvu, pcifunc))
+			return 0;
+		rvu_get_cgx_lmac_id(rvu->pf2cgxlmac_map[pf], &cgx_id, &lmac_id);
+
+		rc = cgx_set_pkind(rvu_cgx_pdata(cgx_id, rvu), lmac_id,
+				   rxpkind);
+		if (rc)
+			return rc;
+	}
+
+	if (dir & PKIND_TX) {
+		/* Tx pkind set request valid if PCIFUNC has NIXLF attached */
+		rc = nix_get_nixlf(rvu, pcifunc, &nixlf, &blkaddr);
+		if (rc)
+			return rc;
+
+		rvu_write64(rvu, blkaddr, NIX_AF_LFX_TX_PARSE_CFG(nixlf),
+			    txpkind);
+	}
+
+	pfvf->intf_mode = intf_mode;
+	return 0;
+}
+
+int rvu_mbox_handler_npc_set_pkind(struct rvu *rvu, struct npc_set_pkind *req,
+				   struct msg_rsp *rsp)
+{
+	return rvu_npc_set_parse_mode(rvu, req->hdr.pcifunc, req->mode,
+				      req->dir, req->pkind, req->var_len_off,
+				      req->var_len_off_mask, req->shift_dir);
+}
+
 int rvu_mbox_handler_npc_read_base_steer_rule(struct rvu *rvu,
 					      struct msg_req *req,
 					      struct npc_mcam_read_base_rule_rsp *rsp)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc_fs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc_fs.c
@@ -445,7 +445,8 @@
 	NPC_SCAN_HDR(NPC_VLAN_TAG1, NPC_LID_LB, NPC_LT_LB_CTAG, 2, 2);
 	NPC_SCAN_HDR(NPC_VLAN_TAG2, NPC_LID_LB, NPC_LT_LB_STAG_QINQ, 2, 2);
 	NPC_SCAN_HDR(NPC_DMAC, NPC_LID_LA, la_ltype, la_start, 6);
-	NPC_SCAN_HDR(NPC_SMAC, NPC_LID_LA, la_ltype, la_start, 6);
+	/* SMAC follows the DMAC(which is 6 bytes) */
+	NPC_SCAN_HDR(NPC_SMAC, NPC_LID_LA, la_ltype, la_start + 6, 6);
 	/* PF_FUNC is 2 bytes at 0th byte of NPC_LT_LA_IH_NIX_ETHER */
 	NPC_SCAN_HDR(NPC_PF_FUNC, NPC_LID_LA, NPC_LT_LA_IH_NIX_ETHER, 0, 2);
 }
@@ -1098,14 +1099,6 @@
 		write_req.cntr = rule->cntr;
 	}
 
-	err = rvu_mbox_handler_npc_mcam_write_entry(rvu, &write_req,
-						    &write_rsp);
-	if (err) {
-		rvu_mcam_remove_counter_from_rule(rvu, owner, rule);
-		if (new)
-			kfree(rule);
-		return err;
-	}
 	/* update rule */
 	memcpy(&rule->packet, &dummy.packet, sizeof(rule->packet));
 	memcpy(&rule->mask, &dummy.mask, sizeof(rule->mask));
@@ -1129,6 +1122,18 @@
 	if (req->default_rule)
 		pfvf->def_ucast_rule = rule;
 
+	/* write to mcam entry registers */
+	err = rvu_mbox_handler_npc_mcam_write_entry(rvu, &write_req,
+						    &write_rsp);
+	if (err) {
+		rvu_mcam_remove_counter_from_rule(rvu, owner, rule);
+		if (new) {
+			list_del(&rule->list);
+			kfree(rule);
+		}
+		return err;
+	}
+
 	/* VF's MAC address is being changed via PF  */
 	if (pf_set_vfs_mac) {
 		ether_addr_copy(pfvf->default_mac, req->packet.dmac);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_reg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_reg.c
@@ -31,8 +31,8 @@
 	{NIX_TXSCH_LVL_TL4, 3, 0xFFFF, {{0x0B00, 0x0B08}, {0x0B10, 0x0B18},
 			      {0x1200, 0x12E0} } },
 	{NIX_TXSCH_LVL_TL3, 4, 0xFFFF, {{0x1000, 0x10E0}, {0x1600, 0x1608},
-			      {0x1610, 0x1618}, {0x1700, 0x17B0} } },
-	{NIX_TXSCH_LVL_TL2, 2, 0xFFFF, {{0x0E00, 0x0EE0}, {0x1700, 0x17B0} } },
+			      {0x1610, 0x1618}, {0x1700, 0x17C8} } },
+	{NIX_TXSCH_LVL_TL2, 2, 0xFFFF, {{0x0E00, 0x0EE0}, {0x1700, 0x17C8} } },
 	{NIX_TXSCH_LVL_TL1, 1, 0xFFFF, {{0x0C00, 0x0D98} } },
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_reg.h
@@ -670,6 +670,7 @@
 #define NDC_AF_INTR_ENA_W1S		(0x00068)
 #define NDC_AF_INTR_ENA_W1C		(0x00070)
 #define NDC_AF_ACTIVE_PC		(0x00078)
+#define NDC_AF_CAMS_RD_INTERVAL		(0x00080)
 #define NDC_AF_BP_TEST_ENABLE		(0x001F8)
 #define NDC_AF_BP_TEST(a)		(0x00200 | (a) << 3)
 #define NDC_AF_BLK_RST			(0x002F0)
@@ -685,6 +686,8 @@
 		(0x00F00 | (a) << 5 | (b) << 4)
 #define NDC_AF_BANKX_HIT_PC(a)		(0x01000 | (a) << 3)
 #define NDC_AF_BANKX_MISS_PC(a)		(0x01100 | (a) << 3)
+#define NDC_AF_BANKX_LINEX_METADATA(a, b) \
+		(0x10000 | (a) << 12 | (b) << 3)
 
 /* LBK */
 #define LBK_CONST			(0x10ull)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/af/rvu_sdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/af/rvu_sdp.c
@@ -62,15 +62,18 @@
 		pfvf->sdp_info = devm_kzalloc(rvu->dev,
 					      sizeof(struct sdp_node_info),
 					      GFP_KERNEL);
-		if (!pfvf->sdp_info)
+		if (!pfvf->sdp_info) {
+			pci_dev_put(pdev);
 			return -ENOMEM;
+		}
 
 		dev_info(rvu->dev, "SDP PF number:%d\n", sdp_pf_num[i]);
 
-		put_device(&pdev->dev);
 		i++;
 	}
 
+	pci_dev_put(pdev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/cn10k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/cn10k.c
@@ -202,6 +202,11 @@
 
 	rsp = (struct  nix_bandprof_alloc_rsp *)
 	       otx2_mbox_get_rsp(&pfvf->mbox.mbox, 0, &req->hdr);
+	if (IS_ERR(rsp)) {
+		rc = PTR_ERR(rsp);
+		goto out;
+	}
+
 	if (!rsp->prof_count[BAND_PROF_LEAF_LAYER]) {
 		rc = -EIO;
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.c
@@ -188,7 +188,7 @@
 		return PTR_ERR(msghdr);
 	}
 	rsp = (struct nix_get_mac_addr_rsp *)msghdr;
-	ether_addr_copy(netdev->dev_addr, rsp->mac_addr);
+	eth_hw_addr_set(netdev, rsp->mac_addr);
 	mutex_unlock(&pfvf->mbox.lock);
 
 	return 0;
@@ -262,6 +262,7 @@
 	mutex_unlock(&pfvf->mbox.lock);
 	return err;
 }
+EXPORT_SYMBOL(otx2_config_pause_frm);
 
 int otx2_set_flowkey_cfg(struct otx2_nic *pfvf)
 {
@@ -631,6 +632,12 @@
 		req->num_regs++;
 		req->reg[1] = NIX_AF_TL3X_SCHEDULE(schq);
 		req->regval[1] = dwrr_val;
+		if (lvl == hw->txschq_link_cfg_lvl) {
+			req->num_regs++;
+			req->reg[2] = NIX_AF_TL3_TL2X_LINKX_CFG(schq, hw->tx_link);
+			/* Enable this queue and backpressure */
+			req->regval[2] = BIT_ULL(13) | BIT_ULL(12);
+		}
 	} else if (lvl == NIX_TXSCH_LVL_TL2) {
 		parent =  hw->txschq_list[NIX_TXSCH_LVL_TL1][0];
 		req->reg[0] = NIX_AF_TL2X_PARENT(schq);
@@ -640,11 +647,12 @@
 		req->reg[1] = NIX_AF_TL2X_SCHEDULE(schq);
 		req->regval[1] = TXSCH_TL1_DFLT_RR_PRIO << 24 | dwrr_val;
 
-		req->num_regs++;
-		req->reg[2] = NIX_AF_TL3_TL2X_LINKX_CFG(schq, hw->tx_link);
-		/* Enable this queue and backpressure */
-		req->regval[2] = BIT_ULL(13) | BIT_ULL(12);
-
+		if (lvl == hw->txschq_link_cfg_lvl) {
+			req->num_regs++;
+			req->reg[2] = NIX_AF_TL3_TL2X_LINKX_CFG(schq, hw->tx_link);
+			/* Enable this queue and backpressure */
+			req->regval[2] = BIT_ULL(13) | BIT_ULL(12);
+		}
 	} else if (lvl == NIX_TXSCH_LVL_TL1) {
 		/* Default config for TL1.
 		 * For VF this is always ignored.
@@ -848,8 +856,11 @@
 	if (pfvf->ptp) {
 		err = qmem_alloc(pfvf->dev, &sq->timestamps, qset->sqe_cnt,
 				 sizeof(*sq->timestamps));
-		if (err)
+		if (err) {
+			kfree(sq->sg);
+			sq->sg = NULL;
 			return err;
+		}
 	}
 
 	sq->head = 0;
@@ -864,7 +875,14 @@
 	sq->stats.bytes = 0;
 	sq->stats.pkts = 0;
 
-	return pfvf->hw_ops->sq_aq_init(pfvf, qidx, sqb_aura);
+	err = pfvf->hw_ops->sq_aq_init(pfvf, qidx, sqb_aura);
+	if (err) {
+		kfree(sq->sg);
+		sq->sg = NULL;
+		return err;
+	}
+
+	return 0;
 
 }
 
@@ -1006,6 +1024,9 @@
 			return err;
 	}
 
+	pfvf->cq_op_addr = (__force u64 *)otx2_get_regaddr(pfvf,
+							   NIX_LF_CQ_OP_STATUS);
+
 	/* Initialize work queue for receive buffer refill */
 	pfvf->refill_wrk = devm_kcalloc(pfvf->dev, pfvf->qset.cq_cnt,
 					sizeof(struct refill_work), GFP_KERNEL);
@@ -1312,18 +1333,23 @@
 		sq = &qset->sq[qidx];
 		sq->sqb_count = 0;
 		sq->sqb_ptrs = kcalloc(num_sqbs, sizeof(*sq->sqb_ptrs), GFP_KERNEL);
-		if (!sq->sqb_ptrs)
-			return -ENOMEM;
+		if (!sq->sqb_ptrs) {
+			err = -ENOMEM;
+			goto err_mem;
+		}
 
 		for (ptr = 0; ptr < num_sqbs; ptr++) {
-			if (otx2_alloc_rbuf(pfvf, pool, &bufptr))
-				return -ENOMEM;
+			err = otx2_alloc_rbuf(pfvf, pool, &bufptr);
+			if (err)
+				goto err_mem;
 			pfvf->hw_ops->aura_freeptr(pfvf, pool_id, bufptr);
 			sq->sqb_ptrs[sq->sqb_count++] = (u64)bufptr;
 		}
 	}
 
-	return 0;
+err_mem:
+	return err ? -ENOMEM : 0;
+
 fail:
 	otx2_mbox_reset(&pfvf->mbox.mbox, 0);
 	otx2_aura_pool_free(pfvf);
@@ -1366,13 +1392,13 @@
 	for (pool_id = 0; pool_id < hw->rqpool_cnt; pool_id++) {
 		pool = &pfvf->qset.pool[pool_id];
 		for (ptr = 0; ptr < num_ptrs; ptr++) {
-			if (otx2_alloc_rbuf(pfvf, pool, &bufptr))
+			err = otx2_alloc_rbuf(pfvf, pool, &bufptr);
+			if (err)
 				return -ENOMEM;
 			pfvf->hw_ops->aura_freeptr(pfvf, pool_id,
 						   bufptr + OTX2_HEAD_ROOM);
 		}
 	}
-
 	return 0;
 fail:
 	otx2_mbox_reset(&pfvf->mbox.mbox, 0);
@@ -1563,6 +1589,8 @@
 		for (schq = 0; schq < rsp->schq[lvl]; schq++)
 			pf->hw.txschq_list[lvl][schq] =
 				rsp->schq_list[lvl][schq];
+
+	pf->hw.txschq_link_cfg_lvl = rsp->link_cfg_lvl;
 }
 EXPORT_SYMBOL(mbox_handler_nix_txsch_alloc);
 
@@ -1668,6 +1696,10 @@
 	if (!rc) {
 		rsp = (struct nix_hw_info *)
 		       otx2_mbox_get_rsp(&pfvf->mbox.mbox, 0, &req->hdr);
+		if (IS_ERR(rsp)) {
+			rc = PTR_ERR(rsp);
+			goto out;
+		}
 
 		/* HW counts VLAN insertion bytes (8 for double tag)
 		 * irrespective of whether SQE is requesting to insert VLAN
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.h
@@ -182,6 +182,7 @@
 	u16			sqb_size;
 
 	/* NIX */
+	u8			txschq_link_cfg_lvl;
 	u16		txschq_list[NIX_TXSCH_LVL_CNT][MAX_TXSCHQ_PER_FUNC];
 	u16			matchall_ipolicer;
 	u32			dwrr_mtu;
@@ -336,6 +337,7 @@
 #define OTX2_FLAG_TC_MATCHALL_INGRESS_ENABLED	BIT_ULL(13)
 #define OTX2_FLAG_DMACFLTR_SUPPORT		BIT_ULL(14)
 	u64			flags;
+	u64			*cq_op_addr;
 
 	struct otx2_qset	qset;
 	struct otx2_hw		hw;
@@ -591,6 +593,7 @@
 			size++;
 		tar_addr |=  ((size - 1) & 0x7) << 4;
 	}
+	dma_wmb();
 	memcpy((u64 *)lmt_info->lmt_addr, ptrs, sizeof(u64) * num_ptrs);
 	/* Perform LMTST flush */
 	cn10k_lmt_flush(val, tar_addr);
@@ -602,8 +605,10 @@
 	u64 ptrs[2];
 
 	ptrs[1] = buf;
+	get_cpu();
 	/* Free only one buffer at time during init and teardown */
 	__cn10k_aura_freeptr(pfvf, aura, ptrs, 2);
+	put_cpu();
 }
 
 /* Alloc pointer from pool/aura */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_ethtool.c
@@ -316,16 +316,25 @@
 	if (is_otx2_lbkvf(pfvf->pdev))
 		return;
 
+	mutex_lock(&pfvf->mbox.lock);
 	req = otx2_mbox_alloc_msg_cgx_cfg_pause_frm(&pfvf->mbox);
-	if (!req)
+	if (!req) {
+		mutex_unlock(&pfvf->mbox.lock);
 		return;
+	}
 
 	if (!otx2_sync_mbox_msg(&pfvf->mbox)) {
 		rsp = (struct cgx_pause_frm_cfg *)
 		       otx2_mbox_get_rsp(&pfvf->mbox.mbox, 0, &req->hdr);
+		if (IS_ERR(rsp)) {
+			mutex_unlock(&pfvf->mbox.lock);
+			return;
+		}
+
 		pause->rx_pause = rsp->rx_pause;
 		pause->tx_pause = rsp->tx_pause;
 	}
+	mutex_unlock(&pfvf->mbox.lock);
 }
 
 static int otx2_set_pauseparam(struct net_device *netdev,
@@ -992,6 +1001,11 @@
 
 	rsp = (struct fec_mode *)otx2_mbox_get_rsp(&pfvf->mbox.mbox,
 						   0, &req->hdr);
+	if (IS_ERR(rsp)) {
+		err = PTR_ERR(rsp);
+		goto end;
+	}
+
 	if (rsp->fec >= 0)
 		pfvf->linfo.fec = rsp->fec;
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_flows.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_flows.c
@@ -748,7 +748,7 @@
 
 		/* NPC profile doesn't extract AH/ESP header fields */
 		if ((ah_esp_mask->spi & ah_esp_hdr->spi) ||
-		    (ah_esp_mask->tclass & ah_esp_mask->tclass))
+		    (ah_esp_mask->tclass & ah_esp_hdr->tclass))
 			return -EOPNOTSUPP;
 
 		if (flow_type == AH_V6_FLOW)
@@ -827,6 +827,14 @@
 				return -EINVAL;
 
 			vlan_etype = be16_to_cpu(fsp->h_ext.vlan_etype);
+
+			/* Drop rule with vlan_etype == 802.1Q
+			 * and vlan_id == 0 is not supported
+			 */
+			if (vlan_etype == ETH_P_8021Q && !fsp->m_ext.vlan_tci &&
+			    fsp->ring_cookie == RX_CLS_FLOW_DISC)
+				return -EINVAL;
+
 			/* Only ETH_P_8021Q and ETH_P_802AD types supported */
 			if (vlan_etype != ETH_P_8021Q &&
 			    vlan_etype != ETH_P_8021AD)
@@ -994,6 +1002,7 @@
 	struct ethhdr *eth_hdr;
 	bool new = false;
 	int err = 0;
+	u64 vf_num;
 	u32 ring;
 
 	if (!flow_cfg->max_flows) {
@@ -1006,7 +1015,21 @@
 	if (!(pfvf->flags & OTX2_FLAG_NTUPLE_SUPPORT))
 		return -ENOMEM;
 
-	if (ring >= pfvf->hw.rx_queues && fsp->ring_cookie != RX_CLS_FLOW_DISC)
+	/* Number of queues on a VF can be greater or less than
+	 * the PF's queue. Hence no need to check for the
+	 * queue count. Hence no need to check queue count if PF
+	 * is installing for its VF. Below is the expected vf_num value
+	 * based on the ethtool commands.
+	 *
+	 * e.g.
+	 * 1. ethtool -U <netdev> ... action -1  ==> vf_num:255
+	 * 2. ethtool -U <netdev> ... action <queue_num>  ==> vf_num:0
+	 * 3. ethtool -U <netdev> ... vf <vf_idx> queue <queue_num>  ==>
+	 *    vf_num:vf_idx+1
+	 */
+	vf_num = ethtool_get_flow_spec_ring_vf(fsp->ring_cookie);
+	if (!is_otx2_vf(pfvf->pcifunc) && !vf_num &&
+	    ring >= pfvf->hw.rx_queues && fsp->ring_cookie != RX_CLS_FLOW_DISC)
 		return -EINVAL;
 
 	if (fsp->location >= otx2_get_maxflows(flow_cfg))
@@ -1088,6 +1111,9 @@
 		flow_cfg->nr_flows++;
 	}
 
+	if (flow->is_vf)
+		netdev_info(pfvf->netdev,
+			    "Make sure that VF's queue number is within its queue limit\n");
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c
@@ -13,6 +13,7 @@
 #include <linux/if_vlan.h>
 #include <linux/iommu.h>
 #include <net/ip.h>
+#include <linux/bitfield.h>
 
 #include "otx2_reg.h"
 #include "otx2_common.h"
@@ -386,7 +387,12 @@
 		dst_mdev->msg_size = mbox_hdr->msg_size;
 		dst_mdev->num_msgs = num_msgs;
 		err = otx2_sync_mbox_msg(dst_mbox);
-		if (err) {
+		/* Error code -EIO indicate there is a communication failure
+		 * to the AF. Rest of the error codes indicate that AF processed
+		 * VF messages and set the error codes in response messages
+		 * (if any) so simply forward responses to VF.
+		 */
+		if (err == -EIO) {
 			dev_warn(pf->dev,
 				 "AF not responding to VF%d messages\n", vf);
 			/* restore PF mbase and exit */
@@ -551,7 +557,9 @@
 		otx2_write64(pf, RVU_PF_VFPF_MBOX_INTX(1), intr);
 		otx2_queue_work(mbox, pf->mbox_pfvf_wq, 64, vfs, intr,
 				TYPE_PFVF);
-		vfs -= 64;
+		if (intr)
+			trace_otx2_msg_interrupt(mbox->mbox.pdev, "VF(s) to PF", intr);
+		vfs = 64;
 	}
 
 	intr = otx2_read64(pf, RVU_PF_VFPF_MBOX_INTX(0));
@@ -559,7 +567,8 @@
 
 	otx2_queue_work(mbox, pf->mbox_pfvf_wq, 0, vfs, intr, TYPE_PFVF);
 
-	trace_otx2_msg_interrupt(mbox->mbox.pdev, "VF(s) to PF", intr);
+	if (intr)
+		trace_otx2_msg_interrupt(mbox->mbox.pdev, "VF(s) to PF", intr);
 
 	return IRQ_HANDLED;
 }
@@ -1148,6 +1157,60 @@
 }
 EXPORT_SYMBOL(otx2_set_real_num_queues);
 
+static char *nix_sqoperr_e_str[NIX_SQOPERR_MAX] = {
+	"NIX_SQOPERR_OOR",
+	"NIX_SQOPERR_CTX_FAULT",
+	"NIX_SQOPERR_CTX_POISON",
+	"NIX_SQOPERR_DISABLED",
+	"NIX_SQOPERR_SIZE_ERR",
+	"NIX_SQOPERR_OFLOW",
+	"NIX_SQOPERR_SQB_NULL",
+	"NIX_SQOPERR_SQB_FAULT",
+	"NIX_SQOPERR_SQE_SZ_ZERO",
+};
+
+static char *nix_mnqerr_e_str[NIX_MNQERR_MAX] = {
+	"NIX_MNQERR_SQ_CTX_FAULT",
+	"NIX_MNQERR_SQ_CTX_POISON",
+	"NIX_MNQERR_SQB_FAULT",
+	"NIX_MNQERR_SQB_POISON",
+	"NIX_MNQERR_TOTAL_ERR",
+	"NIX_MNQERR_LSO_ERR",
+	"NIX_MNQERR_CQ_QUERY_ERR",
+	"NIX_MNQERR_MAX_SQE_SIZE_ERR",
+	"NIX_MNQERR_MAXLEN_ERR",
+	"NIX_MNQERR_SQE_SIZEM1_ZERO",
+};
+
+static char *nix_snd_status_e_str[NIX_SND_STATUS_MAX] =  {
+	[NIX_SND_STATUS_GOOD] = "NIX_SND_STATUS_GOOD",
+	[NIX_SND_STATUS_SQ_CTX_FAULT] = "NIX_SND_STATUS_SQ_CTX_FAULT",
+	[NIX_SND_STATUS_SQ_CTX_POISON] = "NIX_SND_STATUS_SQ_CTX_POISON",
+	[NIX_SND_STATUS_SQB_FAULT] = "NIX_SND_STATUS_SQB_FAULT",
+	[NIX_SND_STATUS_SQB_POISON] = "NIX_SND_STATUS_SQB_POISON",
+	[NIX_SND_STATUS_HDR_ERR] = "NIX_SND_STATUS_HDR_ERR",
+	[NIX_SND_STATUS_EXT_ERR] = "NIX_SND_STATUS_EXT_ERR",
+	[NIX_SND_STATUS_JUMP_FAULT] = "NIX_SND_STATUS_JUMP_FAULT",
+	[NIX_SND_STATUS_JUMP_POISON] = "NIX_SND_STATUS_JUMP_POISON",
+	[NIX_SND_STATUS_CRC_ERR] = "NIX_SND_STATUS_CRC_ERR",
+	[NIX_SND_STATUS_IMM_ERR] = "NIX_SND_STATUS_IMM_ERR",
+	[NIX_SND_STATUS_SG_ERR] = "NIX_SND_STATUS_SG_ERR",
+	[NIX_SND_STATUS_MEM_ERR] = "NIX_SND_STATUS_MEM_ERR",
+	[NIX_SND_STATUS_INVALID_SUBDC] = "NIX_SND_STATUS_INVALID_SUBDC",
+	[NIX_SND_STATUS_SUBDC_ORDER_ERR] = "NIX_SND_STATUS_SUBDC_ORDER_ERR",
+	[NIX_SND_STATUS_DATA_FAULT] = "NIX_SND_STATUS_DATA_FAULT",
+	[NIX_SND_STATUS_DATA_POISON] = "NIX_SND_STATUS_DATA_POISON",
+	[NIX_SND_STATUS_NPC_DROP_ACTION] = "NIX_SND_STATUS_NPC_DROP_ACTION",
+	[NIX_SND_STATUS_LOCK_VIOL] = "NIX_SND_STATUS_LOCK_VIOL",
+	[NIX_SND_STATUS_NPC_UCAST_CHAN_ERR] = "NIX_SND_STAT_NPC_UCAST_CHAN_ERR",
+	[NIX_SND_STATUS_NPC_MCAST_CHAN_ERR] = "NIX_SND_STAT_NPC_MCAST_CHAN_ERR",
+	[NIX_SND_STATUS_NPC_MCAST_ABORT] = "NIX_SND_STATUS_NPC_MCAST_ABORT",
+	[NIX_SND_STATUS_NPC_VTAG_PTR_ERR] = "NIX_SND_STATUS_NPC_VTAG_PTR_ERR",
+	[NIX_SND_STATUS_NPC_VTAG_SIZE_ERR] = "NIX_SND_STATUS_NPC_VTAG_SIZE_ERR",
+	[NIX_SND_STATUS_SEND_MEM_FAULT] = "NIX_SND_STATUS_SEND_MEM_FAULT",
+	[NIX_SND_STATUS_SEND_STATS_ERR] = "NIX_SND_STATUS_SEND_STATS_ERR",
+};
+
 static irqreturn_t otx2_q_intr_handler(int irq, void *data)
 {
 	struct otx2_nic *pf = data;
@@ -1165,14 +1228,16 @@
 			continue;
 
 		if (val & BIT_ULL(42)) {
-			netdev_err(pf->netdev, "CQ%lld: error reading NIX_LF_CQ_OP_INT, NIX_LF_ERR_INT 0x%llx\n",
+			netdev_err(pf->netdev,
+				   "CQ%lld: error reading NIX_LF_CQ_OP_INT, NIX_LF_ERR_INT 0x%llx\n",
 				   qidx, otx2_read64(pf, NIX_LF_ERR_INT));
 		} else {
 			if (val & BIT_ULL(NIX_CQERRINT_DOOR_ERR))
 				netdev_err(pf->netdev, "CQ%lld: Doorbell error",
 					   qidx);
 			if (val & BIT_ULL(NIX_CQERRINT_CQE_FAULT))
-				netdev_err(pf->netdev, "CQ%lld: Memory fault on CQE write to LLC/DRAM",
+				netdev_err(pf->netdev,
+					   "CQ%lld: Memory fault on CQE write to LLC/DRAM",
 					   qidx);
 		}
 
@@ -1181,46 +1246,76 @@
 
 	/* SQ */
 	for (qidx = 0; qidx < pf->hw.tx_queues; qidx++) {
+		u64 sq_op_err_dbg, mnq_err_dbg, snd_err_dbg;
+		u8 sq_op_err_code, mnq_err_code, snd_err_code;
+
+		/* Below debug registers captures first errors corresponding to
+		 * those registers. We don't have to check against SQ qid as
+		 * these are fatal errors.
+		 */
+
 		ptr = otx2_get_regaddr(pf, NIX_LF_SQ_OP_INT);
 		val = otx2_atomic64_add((qidx << 44), ptr);
 		otx2_write64(pf, NIX_LF_SQ_OP_INT, (qidx << 44) |
 			     (val & NIX_SQINT_BITS));
 
-		if (!(val & (NIX_SQINT_BITS | BIT_ULL(42))))
-			continue;
-
 		if (val & BIT_ULL(42)) {
-			netdev_err(pf->netdev, "SQ%lld: error reading NIX_LF_SQ_OP_INT, NIX_LF_ERR_INT 0x%llx\n",
+			netdev_err(pf->netdev,
+				   "SQ%lld: error reading NIX_LF_SQ_OP_INT, NIX_LF_ERR_INT 0x%llx\n",
 				   qidx, otx2_read64(pf, NIX_LF_ERR_INT));
-		} else {
-			if (val & BIT_ULL(NIX_SQINT_LMT_ERR)) {
-				netdev_err(pf->netdev, "SQ%lld: LMT store error NIX_LF_SQ_OP_ERR_DBG:0x%llx",
-					   qidx,
-					   otx2_read64(pf,
-						       NIX_LF_SQ_OP_ERR_DBG));
-				otx2_write64(pf, NIX_LF_SQ_OP_ERR_DBG,
-					     BIT_ULL(44));
-			}
-			if (val & BIT_ULL(NIX_SQINT_MNQ_ERR)) {
-				netdev_err(pf->netdev, "SQ%lld: Meta-descriptor enqueue error NIX_LF_MNQ_ERR_DGB:0x%llx\n",
-					   qidx,
-					   otx2_read64(pf, NIX_LF_MNQ_ERR_DBG));
-				otx2_write64(pf, NIX_LF_MNQ_ERR_DBG,
-					     BIT_ULL(44));
-			}
-			if (val & BIT_ULL(NIX_SQINT_SEND_ERR)) {
-				netdev_err(pf->netdev, "SQ%lld: Send error, NIX_LF_SEND_ERR_DBG 0x%llx",
-					   qidx,
-					   otx2_read64(pf,
-						       NIX_LF_SEND_ERR_DBG));
-				otx2_write64(pf, NIX_LF_SEND_ERR_DBG,
-					     BIT_ULL(44));
-			}
-			if (val & BIT_ULL(NIX_SQINT_SQB_ALLOC_FAIL))
-				netdev_err(pf->netdev, "SQ%lld: SQB allocation failed",
-					   qidx);
+			goto done;
 		}
 
+		sq_op_err_dbg = otx2_read64(pf, NIX_LF_SQ_OP_ERR_DBG);
+		if (!(sq_op_err_dbg & BIT(44)))
+			goto chk_mnq_err_dbg;
+
+		sq_op_err_code = FIELD_GET(GENMASK(7, 0), sq_op_err_dbg);
+		netdev_err(pf->netdev,
+			   "SQ%lld: NIX_LF_SQ_OP_ERR_DBG(0x%llx)  err=%s(%#x)\n",
+			   qidx, sq_op_err_dbg,
+			   nix_sqoperr_e_str[sq_op_err_code],
+			   sq_op_err_code);
+
+		otx2_write64(pf, NIX_LF_SQ_OP_ERR_DBG, BIT_ULL(44));
+
+		if (sq_op_err_code == NIX_SQOPERR_SQB_NULL)
+			goto chk_mnq_err_dbg;
+
+		/* Err is not NIX_SQOPERR_SQB_NULL, call aq function to read SQ structure.
+		 * TODO: But we are in irq context. How to call mbox functions which does sleep
+		 */
+
+chk_mnq_err_dbg:
+		mnq_err_dbg = otx2_read64(pf, NIX_LF_MNQ_ERR_DBG);
+		if (!(mnq_err_dbg & BIT(44)))
+			goto chk_snd_err_dbg;
+
+		mnq_err_code = FIELD_GET(GENMASK(7, 0), mnq_err_dbg);
+		netdev_err(pf->netdev,
+			   "SQ%lld: NIX_LF_MNQ_ERR_DBG(0x%llx)  err=%s(%#x)\n",
+			   qidx, mnq_err_dbg,  nix_mnqerr_e_str[mnq_err_code],
+			   mnq_err_code);
+		otx2_write64(pf, NIX_LF_MNQ_ERR_DBG, BIT_ULL(44));
+
+chk_snd_err_dbg:
+		snd_err_dbg = otx2_read64(pf, NIX_LF_SEND_ERR_DBG);
+		if (snd_err_dbg & BIT(44)) {
+			snd_err_code = FIELD_GET(GENMASK(7, 0), snd_err_dbg);
+			netdev_err(pf->netdev,
+				   "SQ%lld: NIX_LF_SND_ERR_DBG:0x%llx err=%s(%#x)\n",
+				   qidx, snd_err_dbg,
+				   nix_snd_status_e_str[snd_err_code],
+				   snd_err_code);
+			otx2_write64(pf, NIX_LF_SEND_ERR_DBG, BIT_ULL(44));
+		}
+
+done:
+		/* Print values and reset */
+		if (val & BIT_ULL(NIX_SQINT_SQB_ALLOC_FAIL))
+			netdev_err(pf->netdev, "SQ%lld: SQB allocation failed",
+				   qidx);
+
 		schedule_work(&pf->reset_task);
 	}
 
@@ -1350,8 +1445,9 @@
 	if (err)
 		goto err_free_npa_lf;
 
-	/* Enable backpressure */
-	otx2_nix_config_bp(pf, true);
+	/* Enable backpressure for CGX mapped PF/VFs */
+	if (!is_otx2_lbkvf(pf->pdev))
+		otx2_nix_config_bp(pf, true);
 
 	/* Init Auras and pools used by NIX RQ, for free buffer ptrs */
 	err = otx2_rq_aura_pool_init(pf);
@@ -1493,6 +1589,60 @@
 	mutex_unlock(&mbox->lock);
 }
 
+static bool otx2_promisc_use_mce_list(struct otx2_nic *pfvf)
+{
+	int vf;
+
+	/* The AF driver will determine whether to allow the VF netdev or not */
+	if (is_otx2_vf(pfvf->pcifunc))
+		return true;
+
+	/* check if there are any trusted VFs associated with the PF netdev */
+	for (vf = 0; vf < pci_num_vf(pfvf->pdev); vf++)
+		if (pfvf->vf_configs[vf].trusted)
+			return true;
+	return false;
+}
+
+static void otx2_do_set_rx_mode(struct otx2_nic *pf)
+{
+	struct net_device *netdev = pf->netdev;
+	struct nix_rx_mode *req;
+	bool promisc = false;
+
+	if (!(netdev->flags & IFF_UP))
+		return;
+
+	if ((netdev->flags & IFF_PROMISC) ||
+	    (netdev_uc_count(netdev) > OTX2_MAX_UNICAST_FLOWS)) {
+		promisc = true;
+	}
+
+	/* Write unicast address to mcam entries or del from mcam */
+	if (!promisc && netdev->priv_flags & IFF_UNICAST_FLT)
+		__dev_uc_sync(netdev, otx2_add_macfilter, otx2_del_macfilter);
+
+	mutex_lock(&pf->mbox.lock);
+	req = otx2_mbox_alloc_msg_nix_set_rx_mode(&pf->mbox);
+	if (!req) {
+		mutex_unlock(&pf->mbox.lock);
+		return;
+	}
+
+	req->mode = NIX_RX_MODE_UCAST;
+
+	if (promisc)
+		req->mode |= NIX_RX_MODE_PROMISC;
+	if (netdev->flags & (IFF_ALLMULTI | IFF_MULTICAST))
+		req->mode |= NIX_RX_MODE_ALLMULTI;
+
+	if (otx2_promisc_use_mce_list(pf))
+		req->mode |= NIX_RX_MODE_USE_MCE;
+
+	otx2_sync_mbox_msg(&pf->mbox);
+	mutex_unlock(&pf->mbox.lock);
+}
+
 int otx2_open(struct net_device *netdev)
 {
 	struct otx2_nic *pf = netdev_priv(netdev);
@@ -1635,19 +1785,27 @@
 	if (pf->linfo.link_up && !(pf->pcifunc & RVU_PFVF_FUNC_MASK))
 		otx2_handle_link_event(pf);
 
-	/* Restore pause frame settings */
-	otx2_config_pause_frm(pf);
-
 	/* Install DMAC Filters */
 	if (pf->flags & OTX2_FLAG_DMACFLTR_SUPPORT)
 		otx2_dmacflt_reinstall_flows(pf);
 
 	err = otx2_rxtx_enable(pf, true);
-	if (err)
+	/* If a mbox communication error happens at this point then interface
+	 * will end up in a state such that it is in down state but hardware
+	 * mcam entries are enabled to receive the packets. Hence disable the
+	 * packet I/O.
+	 */
+	if (err == -EIO)
+		goto err_disable_rxtx;
+	else if (err)
 		goto err_tx_stop_queues;
 
+	otx2_do_set_rx_mode(pf);
+
 	return 0;
 
+err_disable_rxtx:
+	otx2_rxtx_enable(pf, false);
 err_tx_stop_queues:
 	netif_tx_stop_all_queues(netdev);
 	netif_carrier_off(netdev);
@@ -1696,6 +1854,8 @@
 	/* Clear RSS enable flag */
 	rss = &pf->hw.rss_info;
 	rss->enable = false;
+	if (!netif_is_rxfh_configured(netdev))
+		kfree(rss->rss_ctx[DEFAULT_RSS_CONTEXT_GROUP]);
 
 	/* Cleanup Queue IRQ */
 	vec = pci_irq_vector(pf->pdev,
@@ -1791,43 +1951,11 @@
 	queue_work(pf->otx2_wq, &pf->rx_mode_work);
 }
 
-static void otx2_do_set_rx_mode(struct work_struct *work)
+static void otx2_rx_mode_wrk_handler(struct work_struct *work)
 {
 	struct otx2_nic *pf = container_of(work, struct otx2_nic, rx_mode_work);
-	struct net_device *netdev = pf->netdev;
-	struct nix_rx_mode *req;
-	bool promisc = false;
 
-	if (!(netdev->flags & IFF_UP))
-		return;
-
-	if ((netdev->flags & IFF_PROMISC) ||
-	    (netdev_uc_count(netdev) > OTX2_MAX_UNICAST_FLOWS)) {
-		promisc = true;
-	}
-
-	/* Write unicast address to mcam entries or del from mcam */
-	if (!promisc && netdev->priv_flags & IFF_UNICAST_FLT)
-		__dev_uc_sync(netdev, otx2_add_macfilter, otx2_del_macfilter);
-
-	mutex_lock(&pf->mbox.lock);
-	req = otx2_mbox_alloc_msg_nix_set_rx_mode(&pf->mbox);
-	if (!req) {
-		mutex_unlock(&pf->mbox.lock);
-		return;
-	}
-
-	req->mode = NIX_RX_MODE_UCAST;
-
-	if (promisc)
-		req->mode |= NIX_RX_MODE_PROMISC;
-	if (netdev->flags & (IFF_ALLMULTI | IFF_MULTICAST))
-		req->mode |= NIX_RX_MODE_ALLMULTI;
-
-	req->mode |= NIX_RX_MODE_USE_MCE;
-
-	otx2_sync_mbox_msg(&pf->mbox);
-	mutex_unlock(&pf->mbox.lock);
+	otx2_do_set_rx_mode(pf);
 }
 
 static int otx2_set_features(struct net_device *netdev,
@@ -2325,11 +2453,14 @@
 	pf->vf_configs[vf].trusted = enable;
 	rc = otx2_set_vf_permissions(pf, vf, OTX2_TRUSTED_VF);
 
-	if (rc)
+	if (rc) {
 		pf->vf_configs[vf].trusted = !enable;
-	else
+	} else {
 		netdev_info(pf->netdev, "VF %d is %strusted\n",
 			    vf, enable ? "" : "not ");
+		otx2_set_rx_mode(netdev);
+	}
+
 	return rc;
 }
 
@@ -2358,7 +2489,7 @@
 	if (!pf->otx2_wq)
 		return -ENOMEM;
 
-	INIT_WORK(&pf->rx_mode_work, otx2_do_set_rx_mode);
+	INIT_WORK(&pf->rx_mode_work, otx2_rx_mode_wrk_handler);
 	INIT_WORK(&pf->reset_task, otx2_reset_task);
 	return 0;
 }
@@ -2643,10 +2774,6 @@
 	/* Enable link notifications */
 	otx2_cgx_config_linkevents(pf, true);
 
-	/* Enable pause frames by default */
-	pf->flags |= OTX2_FLAG_RX_PAUSE_ENABLED;
-	pf->flags |= OTX2_FLAG_TX_PAUSE_ENABLED;
-
 	return 0;
 
 err_pf_sriov_init:
@@ -2790,6 +2917,14 @@
 	if (pf->flags & OTX2_FLAG_RX_TSTAMP_ENABLED)
 		otx2_config_hw_rx_tstamp(pf, false);
 
+	/* Disable 802.3x pause frames */
+	if (pf->flags & OTX2_FLAG_RX_PAUSE_ENABLED ||
+	    (pf->flags & OTX2_FLAG_TX_PAUSE_ENABLED)) {
+		pf->flags &= ~OTX2_FLAG_RX_PAUSE_ENABLED;
+		pf->flags &= ~OTX2_FLAG_TX_PAUSE_ENABLED;
+		otx2_config_pause_frm(pf);
+	}
+
 	cancel_work_sync(&pf->reset_task);
 	/* Disable link notifications */
 	otx2_cgx_config_linkevents(pf, false);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_struct.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_struct.h
@@ -274,4 +274,61 @@
 			BIT_ULL(NIX_SQINT_SEND_ERR) | \
 			BIT_ULL(NIX_SQINT_SQB_ALLOC_FAIL))
 
+enum nix_sqoperr_e {
+	NIX_SQOPERR_OOR = 0,
+	NIX_SQOPERR_CTX_FAULT = 1,
+	NIX_SQOPERR_CTX_POISON = 2,
+	NIX_SQOPERR_DISABLED = 3,
+	NIX_SQOPERR_SIZE_ERR = 4,
+	NIX_SQOPERR_OFLOW = 5,
+	NIX_SQOPERR_SQB_NULL = 6,
+	NIX_SQOPERR_SQB_FAULT = 7,
+	NIX_SQOPERR_SQE_SZ_ZERO = 8,
+	NIX_SQOPERR_MAX,
+};
+
+enum nix_mnqerr_e {
+	NIX_MNQERR_SQ_CTX_FAULT = 0,
+	NIX_MNQERR_SQ_CTX_POISON = 1,
+	NIX_MNQERR_SQB_FAULT = 2,
+	NIX_MNQERR_SQB_POISON = 3,
+	NIX_MNQERR_TOTAL_ERR = 4,
+	NIX_MNQERR_LSO_ERR = 5,
+	NIX_MNQERR_CQ_QUERY_ERR = 6,
+	NIX_MNQERR_MAX_SQE_SIZE_ERR = 7,
+	NIX_MNQERR_MAXLEN_ERR = 8,
+	NIX_MNQERR_SQE_SIZEM1_ZERO = 9,
+	NIX_MNQERR_MAX,
+};
+
+enum nix_snd_status_e {
+	NIX_SND_STATUS_GOOD = 0x0,
+	NIX_SND_STATUS_SQ_CTX_FAULT = 0x1,
+	NIX_SND_STATUS_SQ_CTX_POISON = 0x2,
+	NIX_SND_STATUS_SQB_FAULT = 0x3,
+	NIX_SND_STATUS_SQB_POISON = 0x4,
+	NIX_SND_STATUS_HDR_ERR = 0x5,
+	NIX_SND_STATUS_EXT_ERR = 0x6,
+	NIX_SND_STATUS_JUMP_FAULT = 0x7,
+	NIX_SND_STATUS_JUMP_POISON = 0x8,
+	NIX_SND_STATUS_CRC_ERR = 0x10,
+	NIX_SND_STATUS_IMM_ERR = 0x11,
+	NIX_SND_STATUS_SG_ERR = 0x12,
+	NIX_SND_STATUS_MEM_ERR = 0x13,
+	NIX_SND_STATUS_INVALID_SUBDC = 0x14,
+	NIX_SND_STATUS_SUBDC_ORDER_ERR = 0x15,
+	NIX_SND_STATUS_DATA_FAULT = 0x16,
+	NIX_SND_STATUS_DATA_POISON = 0x17,
+	NIX_SND_STATUS_NPC_DROP_ACTION = 0x20,
+	NIX_SND_STATUS_LOCK_VIOL = 0x21,
+	NIX_SND_STATUS_NPC_UCAST_CHAN_ERR = 0x22,
+	NIX_SND_STATUS_NPC_MCAST_CHAN_ERR = 0x23,
+	NIX_SND_STATUS_NPC_MCAST_ABORT = 0x24,
+	NIX_SND_STATUS_NPC_VTAG_PTR_ERR = 0x25,
+	NIX_SND_STATUS_NPC_VTAG_SIZE_ERR = 0x26,
+	NIX_SND_STATUS_SEND_MEM_FAULT = 0x27,
+	NIX_SND_STATUS_SEND_STATS_ERR = 0x28,
+	NIX_SND_STATUS_MAX,
+};
+
 #endif /* OTX2_STRUCT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_tc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_tc.c
@@ -28,6 +28,9 @@
 #define MAX_RATE_EXPONENT		0x0FULL
 #define MAX_RATE_MANTISSA		0xFFULL
 
+#define CN10K_MAX_BURST_MANTISSA	0x7FFFULL
+#define CN10K_MAX_BURST_SIZE		8453888ULL
+
 /* Bitfields in NIX_TLX_PIR register */
 #define TLX_RATE_MANTISSA		GENMASK_ULL(8, 1)
 #define TLX_RATE_EXPONENT		GENMASK_ULL(12, 9)
@@ -35,6 +38,9 @@
 #define TLX_BURST_MANTISSA		GENMASK_ULL(36, 29)
 #define TLX_BURST_EXPONENT		GENMASK_ULL(40, 37)
 
+#define CN10K_TLX_BURST_MANTISSA	GENMASK_ULL(43, 29)
+#define CN10K_TLX_BURST_EXPONENT	GENMASK_ULL(47, 44)
+
 struct otx2_tc_flow_stats {
 	u64 bytes;
 	u64 pkts;
@@ -77,33 +83,42 @@
 }
 EXPORT_SYMBOL(otx2_tc_alloc_ent_bitmap);
 
-static void otx2_get_egress_burst_cfg(u32 burst, u32 *burst_exp,
-				      u32 *burst_mantissa)
+static void otx2_get_egress_burst_cfg(struct otx2_nic *nic, u32 burst,
+				      u32 *burst_exp, u32 *burst_mantissa)
 {
+	int max_burst, max_mantissa;
 	unsigned int tmp;
 
+	if (is_dev_otx2(nic->pdev)) {
+		max_burst = MAX_BURST_SIZE;
+		max_mantissa = MAX_BURST_MANTISSA;
+	} else {
+		max_burst = CN10K_MAX_BURST_SIZE;
+		max_mantissa = CN10K_MAX_BURST_MANTISSA;
+	}
+
 	/* Burst is calculated as
 	 * ((256 + BURST_MANTISSA) << (1 + BURST_EXPONENT)) / 256
 	 * Max supported burst size is 130,816 bytes.
 	 */
-	burst = min_t(u32, burst, MAX_BURST_SIZE);
+	burst = min_t(u32, burst, max_burst);
 	if (burst) {
 		*burst_exp = ilog2(burst) ? ilog2(burst) - 1 : 0;
 		tmp = burst - rounddown_pow_of_two(burst);
-		if (burst < MAX_BURST_MANTISSA)
+		if (burst < max_mantissa)
 			*burst_mantissa = tmp * 2;
 		else
 			*burst_mantissa = tmp / (1ULL << (*burst_exp - 7));
 	} else {
 		*burst_exp = MAX_BURST_EXPONENT;
-		*burst_mantissa = MAX_BURST_MANTISSA;
+		*burst_mantissa = max_mantissa;
 	}
 }
 
-static void otx2_get_egress_rate_cfg(u32 maxrate, u32 *exp,
+static void otx2_get_egress_rate_cfg(u64 maxrate, u32 *exp,
 				     u32 *mantissa, u32 *div_exp)
 {
-	unsigned int tmp;
+	u64 tmp;
 
 	/* Rate calculation by hardware
 	 *
@@ -132,21 +147,44 @@
 	}
 }
 
-static int otx2_set_matchall_egress_rate(struct otx2_nic *nic, u32 burst, u32 maxrate)
+static u64 otx2_get_txschq_rate_regval(struct otx2_nic *nic,
+				       u64 maxrate, u32 burst)
 {
-	struct otx2_hw *hw = &nic->hw;
-	struct nix_txschq_config *req;
 	u32 burst_exp, burst_mantissa;
 	u32 exp, mantissa, div_exp;
+	u64 regval = 0;
+
+	/* Get exponent and mantissa values from the desired rate */
+	otx2_get_egress_burst_cfg(nic, burst, &burst_exp, &burst_mantissa);
+	otx2_get_egress_rate_cfg(maxrate, &exp, &mantissa, &div_exp);
+
+	if (is_dev_otx2(nic->pdev)) {
+		regval = FIELD_PREP(TLX_BURST_EXPONENT, (u64)burst_exp) |
+				FIELD_PREP(TLX_BURST_MANTISSA, (u64)burst_mantissa) |
+				FIELD_PREP(TLX_RATE_DIVIDER_EXPONENT, div_exp) |
+				FIELD_PREP(TLX_RATE_EXPONENT, exp) |
+				FIELD_PREP(TLX_RATE_MANTISSA, mantissa) | BIT_ULL(0);
+	} else {
+		regval = FIELD_PREP(CN10K_TLX_BURST_EXPONENT, (u64)burst_exp) |
+				FIELD_PREP(CN10K_TLX_BURST_MANTISSA, (u64)burst_mantissa) |
+				FIELD_PREP(TLX_RATE_DIVIDER_EXPONENT, div_exp) |
+				FIELD_PREP(TLX_RATE_EXPONENT, exp) |
+				FIELD_PREP(TLX_RATE_MANTISSA, mantissa) | BIT_ULL(0);
+	}
+
+	return regval;
+}
+
+static int otx2_set_matchall_egress_rate(struct otx2_nic *nic,
+					 u32 burst, u64 maxrate)
+{
+	struct otx2_hw *hw = &nic->hw;
+	struct nix_txschq_config *req;
 	int txschq, err;
 
 	/* All SQs share the same TL4, so pick the first scheduler */
 	txschq = hw->txschq_list[NIX_TXSCH_LVL_TL4][0];
 
-	/* Get exponent and mantissa values from the desired rate */
-	otx2_get_egress_burst_cfg(burst, &burst_exp, &burst_mantissa);
-	otx2_get_egress_rate_cfg(maxrate, &exp, &mantissa, &div_exp);
-
 	mutex_lock(&nic->mbox.lock);
 	req = otx2_mbox_alloc_msg_nix_txschq_cfg(&nic->mbox);
 	if (!req) {
@@ -157,11 +195,7 @@
 	req->lvl = NIX_TXSCH_LVL_TL4;
 	req->num_regs = 1;
 	req->reg[0] = NIX_AF_TL4X_PIR(txschq);
-	req->regval[0] = FIELD_PREP(TLX_BURST_EXPONENT, burst_exp) |
-			 FIELD_PREP(TLX_BURST_MANTISSA, burst_mantissa) |
-			 FIELD_PREP(TLX_RATE_DIVIDER_EXPONENT, div_exp) |
-			 FIELD_PREP(TLX_RATE_EXPONENT, exp) |
-			 FIELD_PREP(TLX_RATE_MANTISSA, mantissa) | BIT_ULL(0);
+	req->regval[0] = otx2_get_txschq_rate_regval(nic, maxrate, burst);
 
 	err = otx2_sync_mbox_msg(&nic->mbox);
 	mutex_unlock(&nic->mbox.lock);
@@ -196,7 +230,7 @@
 	struct netlink_ext_ack *extack = cls->common.extack;
 	struct flow_action *actions = &cls->rule->action;
 	struct flow_action_entry *entry;
-	u32 rate;
+	u64 rate;
 	int err;
 
 	err = otx2_tc_validate_flow(nic, actions, extack);
@@ -218,7 +252,7 @@
 		}
 		/* Convert bytes per second to Mbps */
 		rate = entry->police.rate_bytes_ps * 8;
-		rate = max_t(u32, rate / 1000000, 1);
+		rate = max_t(u64, rate / 1000000, 1);
 		err = otx2_set_matchall_egress_rate(nic, entry->police.burst, rate);
 		if (err)
 			return err;
@@ -502,6 +536,21 @@
 			return -EOPNOTSUPP;
 		}
 
+		if (!match.mask->vlan_id) {
+			struct flow_action_entry *act;
+			int i;
+
+			flow_action_for_each(i, act, &rule->action) {
+				if (act->id == FLOW_ACTION_DROP) {
+					netdev_err(nic->netdev,
+						   "vlan tpid 0x%x with vlan_id %d is not supported for DROP rule.\n",
+						   ntohs(match.key->vlan_tpid),
+						   match.key->vlan_id);
+					return -EOPNOTSUPP;
+				}
+			}
+		}
+
 		if (match.mask->vlan_id ||
 		    match.mask->vlan_dei ||
 		    match.mask->vlan_priority) {
@@ -571,21 +620,27 @@
 
 		flow_spec->dport = match.key->dst;
 		flow_mask->dport = match.mask->dst;
-		if (ip_proto == IPPROTO_UDP)
-			req->features |= BIT_ULL(NPC_DPORT_UDP);
-		else if (ip_proto == IPPROTO_TCP)
-			req->features |= BIT_ULL(NPC_DPORT_TCP);
-		else if (ip_proto == IPPROTO_SCTP)
-			req->features |= BIT_ULL(NPC_DPORT_SCTP);
+
+		if (flow_mask->dport) {
+			if (ip_proto == IPPROTO_UDP)
+				req->features |= BIT_ULL(NPC_DPORT_UDP);
+			else if (ip_proto == IPPROTO_TCP)
+				req->features |= BIT_ULL(NPC_DPORT_TCP);
+			else if (ip_proto == IPPROTO_SCTP)
+				req->features |= BIT_ULL(NPC_DPORT_SCTP);
+		}
 
 		flow_spec->sport = match.key->src;
 		flow_mask->sport = match.mask->src;
-		if (ip_proto == IPPROTO_UDP)
-			req->features |= BIT_ULL(NPC_SPORT_UDP);
-		else if (ip_proto == IPPROTO_TCP)
-			req->features |= BIT_ULL(NPC_SPORT_TCP);
-		else if (ip_proto == IPPROTO_SCTP)
-			req->features |= BIT_ULL(NPC_SPORT_SCTP);
+
+		if (flow_mask->sport) {
+			if (ip_proto == IPPROTO_UDP)
+				req->features |= BIT_ULL(NPC_SPORT_UDP);
+			else if (ip_proto == IPPROTO_TCP)
+				req->features |= BIT_ULL(NPC_SPORT_TCP);
+			else if (ip_proto == IPPROTO_SCTP)
+				req->features |= BIT_ULL(NPC_SPORT_SCTP);
+		}
 	}
 
 	return otx2_tc_parse_actions(nic, &rule->action, req, f, node);
@@ -1050,7 +1105,12 @@
 		return err;
 
 	tc->flow_ht_params = tc_flow_ht_params;
-	return rhashtable_init(&tc->flow_table, &tc->flow_ht_params);
+	err = rhashtable_init(&tc->flow_table, &tc->flow_ht_params);
+	if (err) {
+		kfree(tc->tc_entries_bitmap);
+		tc->tc_entries_bitmap = NULL;
+	}
+	return err;
 }
 
 void otx2_shutdown_tc(struct otx2_nic *nic)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_txrx.c
@@ -18,6 +18,31 @@
 
 #define CQE_ADDR(CQ, idx) ((CQ)->cqe_base + ((CQ)->cqe_size * (idx)))
 
+static int otx2_nix_cq_op_status(struct otx2_nic *pfvf,
+				 struct otx2_cq_queue *cq)
+{
+	u64 incr = (u64)(cq->cq_idx) << 32;
+	u64 status;
+
+	status = otx2_atomic64_fetch_add(incr, pfvf->cq_op_addr);
+
+	if (unlikely(status & BIT_ULL(CQ_OP_STAT_OP_ERR) ||
+		     status & BIT_ULL(CQ_OP_STAT_CQ_ERR))) {
+		dev_err(pfvf->dev, "CQ stopped due to error");
+		return -EINVAL;
+	}
+
+	cq->cq_tail = status & 0xFFFFF;
+	cq->cq_head = (status >> 20) & 0xFFFFF;
+	if (cq->cq_tail < cq->cq_head)
+		cq->pend_cqe = (cq->cqe_cnt - cq->cq_head) +
+				cq->cq_tail;
+	else
+		cq->pend_cqe = cq->cq_tail - cq->cq_head;
+
+	return 0;
+}
+
 static struct nix_cqe_hdr_s *otx2_get_next_cqe(struct otx2_cq_queue *cq)
 {
 	struct nix_cqe_hdr_s *cqe_hdr;
@@ -318,7 +343,14 @@
 	struct nix_cqe_rx_s *cqe;
 	int processed_cqe = 0;
 
-	while (likely(processed_cqe < budget)) {
+	if (cq->pend_cqe >= budget)
+		goto process_cqe;
+
+	if (otx2_nix_cq_op_status(pfvf, cq) || !cq->pend_cqe)
+		return 0;
+
+process_cqe:
+	while (likely(processed_cqe < budget) && cq->pend_cqe) {
 		cqe = (struct nix_cqe_rx_s *)CQE_ADDR(cq, cq->cq_head);
 		if (cqe->hdr.cqe_type == NIX_XQE_TYPE_INVALID ||
 		    !cqe->sg.seg_addr) {
@@ -334,6 +366,7 @@
 		cqe->hdr.cqe_type = NIX_XQE_TYPE_INVALID;
 		cqe->sg.seg_addr = 0x00;
 		processed_cqe++;
+		cq->pend_cqe--;
 	}
 
 	/* Free CQEs to HW */
@@ -368,7 +401,14 @@
 	struct nix_cqe_tx_s *cqe;
 	int processed_cqe = 0;
 
-	while (likely(processed_cqe < budget)) {
+	if (cq->pend_cqe >= budget)
+		goto process_cqe;
+
+	if (otx2_nix_cq_op_status(pfvf, cq) || !cq->pend_cqe)
+		return 0;
+
+process_cqe:
+	while (likely(processed_cqe < budget) && cq->pend_cqe) {
 		cqe = (struct nix_cqe_tx_s *)otx2_get_next_cqe(cq);
 		if (unlikely(!cqe)) {
 			if (!processed_cqe)
@@ -380,6 +420,7 @@
 
 		cqe->hdr.cqe_type = NIX_XQE_TYPE_INVALID;
 		processed_cqe++;
+		cq->pend_cqe--;
 	}
 
 	/* Free CQEs to HW */
@@ -533,9 +574,7 @@
 				htons(ext->lso_sb - skb_network_offset(skb));
 		} else if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6) {
 			ext->lso_format = pfvf->hw.lso_tsov6_idx;
-
-			ipv6_hdr(skb)->payload_len =
-				htons(ext->lso_sb - skb_network_offset(skb));
+			ipv6_hdr(skb)->payload_len = htons(tcp_hdrlen(skb));
 		} else if (skb_shinfo(skb)->gso_type & SKB_GSO_UDP_L4) {
 			__be16 l3_proto = vlan_get_protocol(skb);
 			struct udphdr *udph = udp_hdr(skb);
@@ -894,8 +933,11 @@
 
 	if (skb_shinfo(skb)->gso_size && !is_hw_tso_supported(pfvf, skb)) {
 		/* Insert vlan tag before giving pkt to tso */
-		if (skb_vlan_tag_present(skb))
+		if (skb_vlan_tag_present(skb)) {
 			skb = __vlan_hwaccel_push_inside(skb);
+			if (!skb)
+				return true;
+		}
 		otx2_sq_append_tso(pfvf, sq, skb, qidx);
 		return true;
 	}
@@ -936,10 +978,16 @@
 	int processed_cqe = 0;
 	u64 iova, pa;
 
-	while ((cqe = (struct nix_cqe_rx_s *)otx2_get_next_cqe(cq))) {
-		if (!cqe->sg.subdc)
-			continue;
+	if (otx2_nix_cq_op_status(pfvf, cq) || !cq->pend_cqe)
+		return;
+
+	while (cq->pend_cqe) {
+		cqe = (struct nix_cqe_rx_s *)otx2_get_next_cqe(cq);
 		processed_cqe++;
+		cq->pend_cqe--;
+
+		if (!cqe)
+			continue;
 		if (cqe->sg.segs > 1) {
 			otx2_free_rcv_seg(pfvf, cqe, cq->cq_idx);
 			continue;
@@ -965,7 +1013,16 @@
 
 	sq = &pfvf->qset.sq[cq->cint_idx];
 
-	while ((cqe = (struct nix_cqe_tx_s *)otx2_get_next_cqe(cq))) {
+	if (otx2_nix_cq_op_status(pfvf, cq) || !cq->pend_cqe)
+		return;
+
+	while (cq->pend_cqe) {
+		cqe = (struct nix_cqe_tx_s *)otx2_get_next_cqe(cq);
+		processed_cqe++;
+		cq->pend_cqe--;
+
+		if (!cqe)
+			continue;
 		sg = &sq->sg[cqe->comp.sqe_id];
 		skb = (struct sk_buff *)sg->skb;
 		if (skb) {
@@ -973,7 +1030,6 @@
 			dev_kfree_skb_any(skb);
 			sg->skb = (u64)NULL;
 		}
-		processed_cqe++;
 	}
 
 	/* Free CQEs to HW */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_txrx.h
@@ -56,6 +56,9 @@
  */
 #define CQ_QCOUNT_DEFAULT	1
 
+#define CQ_OP_STAT_OP_ERR       63
+#define CQ_OP_STAT_CQ_ERR       46
+
 struct queue_stats {
 	u64	bytes;
 	u64	pkts;
@@ -122,6 +125,8 @@
 	u16			pool_ptrs;
 	u32			cqe_cnt;
 	u32			cq_head;
+	u32			cq_tail;
+	u32			pend_cqe;
 	void			*cqe_base;
 	struct qmem		*cqe;
 	struct otx2_pool	*rbpool;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c
@@ -630,7 +630,7 @@
 
 	err = otx2vf_realloc_msix_vectors(vf);
 	if (err)
-		goto err_mbox_destroy;
+		goto err_detach_rsrc;
 
 	err = otx2_set_real_num_queues(netdev, qcount, qcount);
 	if (err)
@@ -695,15 +695,12 @@
 	if (err)
 		goto err_unreg_netdev;
 
-	/* Enable pause frames by default */
-	vf->flags |= OTX2_FLAG_RX_PAUSE_ENABLED;
-	vf->flags |= OTX2_FLAG_TX_PAUSE_ENABLED;
-
 	return 0;
 
 err_unreg_netdev:
 	unregister_netdev(netdev);
 err_detach_rsrc:
+	free_percpu(vf->hw.lmt_info);
 	if (test_bit(CN10K_LMTST, &vf->hw.cap_flag))
 		qmem_free(vf->dev, vf->dync_lmt);
 	otx2_detach_resources(&vf->mbox);
@@ -731,6 +728,14 @@
 
 	vf = netdev_priv(netdev);
 
+	/* Disable 802.3x pause frames */
+	if (vf->flags & OTX2_FLAG_RX_PAUSE_ENABLED ||
+	    (vf->flags & OTX2_FLAG_TX_PAUSE_ENABLED)) {
+		vf->flags &= ~OTX2_FLAG_RX_PAUSE_ENABLED;
+		vf->flags &= ~OTX2_FLAG_TX_PAUSE_ENABLED;
+		otx2_config_pause_frm(vf);
+	}
+
 	cancel_work_sync(&vf->reset_task);
 	otx2_unregister_dl(vf);
 	unregister_netdev(netdev);
@@ -738,6 +743,7 @@
 		destroy_workqueue(vf->otx2_wq);
 	otx2vf_disable_mbox_intr(vf);
 	otx2_detach_resources(&vf->mbox);
+	free_percpu(vf->hw.lmt_info);
 	if (test_bit(CN10K_LMTST, &vf->hw.cap_flag))
 		qmem_free(vf->dev, vf->dync_lmt);
 	otx2vf_vfaf_mbox_destroy(vf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/prestera/prestera_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/prestera/prestera_main.c
@@ -54,12 +54,14 @@
 struct prestera_port *prestera_port_find_by_hwid(struct prestera_switch *sw,
 						 u32 dev_id, u32 hw_id)
 {
-	struct prestera_port *port = NULL;
+	struct prestera_port *port = NULL, *tmp;
 
 	read_lock(&sw->port_list_lock);
-	list_for_each_entry(port, &sw->port_list, list) {
-		if (port->dev_id == dev_id && port->hw_id == hw_id)
+	list_for_each_entry(tmp, &sw->port_list, list) {
+		if (tmp->dev_id == dev_id && tmp->hw_id == hw_id) {
+			port = tmp;
 			break;
+		}
 	}
 	read_unlock(&sw->port_list_lock);
 
@@ -68,12 +70,14 @@
 
 struct prestera_port *prestera_find_port(struct prestera_switch *sw, u32 id)
 {
-	struct prestera_port *port = NULL;
+	struct prestera_port *port = NULL, *tmp;
 
 	read_lock(&sw->port_list_lock);
-	list_for_each_entry(port, &sw->port_list, list) {
-		if (port->id == id)
+	list_for_each_entry(tmp, &sw->port_list, list) {
+		if (tmp->id == id) {
+			port = tmp;
 			break;
+		}
 	}
 	read_unlock(&sw->port_list_lock);
 
@@ -137,7 +141,7 @@
 	if (err)
 		return err;
 
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 
 	return 0;
 }
@@ -488,6 +492,7 @@
 		dev_info(prestera_dev(sw), "using random base mac address\n");
 	}
 	of_node_put(base_mac_np);
+	of_node_put(np);
 
 	return prestera_hw_switch_mac_set(sw, sw->base_mac);
 }
@@ -703,23 +708,27 @@
 				      struct net_device *dev,
 				      unsigned long event, void *ptr)
 {
-	struct netdev_notifier_changeupper_info *info = ptr;
+	struct netdev_notifier_info *info = ptr;
+	struct netdev_notifier_changeupper_info *cu_info;
 	struct prestera_port *port = netdev_priv(dev);
 	struct netlink_ext_ack *extack;
 	struct net_device *upper;
 
-	extack = netdev_notifier_info_to_extack(&info->info);
-	upper = info->upper_dev;
+	extack = netdev_notifier_info_to_extack(info);
+	cu_info = container_of(info,
+			       struct netdev_notifier_changeupper_info,
+			       info);
 
 	switch (event) {
 	case NETDEV_PRECHANGEUPPER:
+		upper = cu_info->upper_dev;
 		if (!netif_is_bridge_master(upper) &&
 		    !netif_is_lag_master(upper)) {
 			NL_SET_ERR_MSG_MOD(extack, "Unknown upper device type");
 			return -EINVAL;
 		}
 
-		if (!info->linking)
+		if (!cu_info->linking)
 			break;
 
 		if (netdev_has_any_upper_dev(upper)) {
@@ -728,7 +737,7 @@
 		}
 
 		if (netif_is_lag_master(upper) &&
-		    !prestera_lag_master_check(upper, info->upper_info, extack))
+		    !prestera_lag_master_check(upper, cu_info->upper_info, extack))
 			return -EOPNOTSUPP;
 		if (netif_is_lag_master(upper) && vlan_uses_dev(dev)) {
 			NL_SET_ERR_MSG_MOD(extack,
@@ -744,14 +753,15 @@
 		break;
 
 	case NETDEV_CHANGEUPPER:
+		upper = cu_info->upper_dev;
 		if (netif_is_bridge_master(upper)) {
-			if (info->linking)
+			if (cu_info->linking)
 				return prestera_bridge_port_join(upper, port,
 								 extack);
 			else
 				prestera_bridge_port_leave(upper, port);
 		} else if (netif_is_lag_master(upper)) {
-			if (info->linking)
+			if (cu_info->linking)
 				return prestera_lag_port_add(port, upper);
 			else
 				prestera_lag_port_del(port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/prestera/prestera_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/prestera/prestera_pci.c
@@ -645,7 +645,8 @@
 
 	err = request_firmware_direct(&fw->bin, fw_path, fw->dev.dev);
 	if (err) {
-		if (ver_maj == PRESTERA_SUPP_FW_MAJ_VER) {
+		if (ver_maj != PRESTERA_PREV_FW_MAJ_VER ||
+		    ver_min != PRESTERA_PREV_FW_MIN_VER) {
 			ver_maj = PRESTERA_PREV_FW_MAJ_VER;
 			ver_min = PRESTERA_PREV_FW_MIN_VER;
 
@@ -815,6 +816,7 @@
 static const struct pci_device_id prestera_pci_devices[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0xC804) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0xC80C) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0xCC1E) },
 	{ }
 };
 MODULE_DEVICE_TABLE(pci, prestera_pci_devices);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/prestera/prestera_rxtx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/prestera/prestera_rxtx.c
@@ -776,6 +776,7 @@
 int prestera_rxtx_switch_init(struct prestera_switch *sw)
 {
 	struct prestera_rxtx *rxtx;
+	int err;
 
 	rxtx = kzalloc(sizeof(*rxtx), GFP_KERNEL);
 	if (!rxtx)
@@ -783,7 +784,11 @@
 
 	sw->rxtx = rxtx;
 
-	return prestera_sdma_switch_init(sw);
+	err = prestera_sdma_switch_init(sw);
+	if (err)
+		kfree(rxtx);
+
+	return err;
 }
 
 void prestera_rxtx_switch_fini(struct prestera_switch *sw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/prestera/prestera_switchdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/prestera/prestera_switchdev.c
@@ -497,8 +497,8 @@
 
 	br_port = prestera_bridge_port_add(bridge, port->dev);
 	if (IS_ERR(br_port)) {
-		err = PTR_ERR(br_port);
-		goto err_brport_create;
+		prestera_bridge_put(bridge);
+		return PTR_ERR(br_port);
 	}
 
 	err = switchdev_bridge_port_offload(br_port->dev, port->dev, NULL,
@@ -519,8 +519,6 @@
 	switchdev_bridge_port_unoffload(br_port->dev, NULL, NULL, NULL);
 err_switchdev_offload:
 	prestera_bridge_port_put(br_port);
-err_brport_create:
-	prestera_bridge_put(bridge);
 	return err;
 }
 
@@ -1124,7 +1122,7 @@
 						     prestera_port_obj_attr_set);
 		break;
 	default:
-		err = -EOPNOTSUPP;
+		return NOTIFY_DONE;
 	}
 
 	return notifier_from_errno(err);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/pxa168_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/pxa168_eth.c
@@ -389,7 +389,7 @@
  * Outputs
  * return the calculated entry.
  */
-static u32 hash_function(unsigned char *mac_addr_orig)
+static u32 hash_function(const unsigned char *mac_addr_orig)
 {
 	u32 hash_result;
 	u32 addr0;
@@ -434,7 +434,7 @@
  * -ENOSPC if table full
  */
 static int add_del_hash_entry(struct pxa168_eth_private *pep,
-			      unsigned char *mac_addr,
+			      const unsigned char *mac_addr,
 			      u32 rd, u32 skip, int del)
 {
 	struct addr_table_entry *entry, *start;
@@ -521,7 +521,7 @@
  */
 static void update_hash_table_mac_address(struct pxa168_eth_private *pep,
 					  unsigned char *oaddr,
-					  unsigned char *addr)
+					  const unsigned char *addr)
 {
 	/* Delete old entry */
 	if (oaddr)
@@ -1396,18 +1396,15 @@
 
 	printk(KERN_NOTICE "PXA168 10/100 Ethernet Driver\n");
 
-	clk = devm_clk_get(&pdev->dev, NULL);
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
 	if (IS_ERR(clk)) {
-		dev_err(&pdev->dev, "Fast Ethernet failed to get clock\n");
+		dev_err(&pdev->dev, "Fast Ethernet failed to get and enable clock\n");
 		return -ENODEV;
 	}
-	clk_prepare_enable(clk);
 
 	dev = alloc_etherdev(sizeof(struct pxa168_eth_private));
-	if (!dev) {
-		err = -ENOMEM;
-		goto err_clk;
-	}
+	if (!dev)
+		return -ENOMEM;
 
 	platform_set_drvdata(pdev, dev);
 	pep = netdev_priv(dev);
@@ -1434,7 +1431,7 @@
 
 	INIT_WORK(&pep->tx_timeout_task, pxa168_eth_tx_timeout_task);
 
-	err = of_get_mac_address(pdev->dev.of_node, dev->dev_addr);
+	err = of_get_ethdev_address(pdev->dev.of_node, dev);
 	if (err) {
 		/* try reading the mac address, if set by the bootloader */
 		pxa168_eth_get_mac_address(dev, dev->dev_addr);
@@ -1518,8 +1515,6 @@
 	mdiobus_free(pep->smi_bus);
 err_netdev:
 	free_netdev(dev);
-err_clk:
-	clk_disable_unprepare(clk);
 	return err;
 }
 
@@ -1537,7 +1532,6 @@
 	if (dev->phydev)
 		phy_disconnect(dev->phydev);
 
-	clk_disable_unprepare(pep->clk);
 	mdiobus_unregister(pep->smi_bus);
 	mdiobus_free(pep->smi_bus);
 	unregister_netdev(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/skge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/skge.c
@@ -50,7 +50,6 @@
 #define PHY_RETRIES	        1000
 #define ETH_JUMBO_MTU		9000
 #define TX_WATCHDOG		(5 * HZ)
-#define NAPI_WEIGHT		64
 #define BLINK_MS		250
 #define LINK_HZ			HZ
 
@@ -3828,7 +3827,7 @@
 		dev->features |= NETIF_F_HIGHDMA;
 
 	skge = netdev_priv(dev);
-	netif_napi_add(dev, &skge->napi, skge_poll, NAPI_WEIGHT);
+	netif_napi_add(dev, &skge->napi, skge_poll, NAPI_POLL_WEIGHT);
 	skge->netdev = dev;
 	skge->hw = hw;
 	skge->msg_enable = netif_msg_init(debug, default_msg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/sky2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/sky2.c
@@ -63,7 +63,6 @@
 #define TX_DEF_PENDING		63
 
 #define TX_WATCHDOG		(5 * HZ)
-#define NAPI_WEIGHT		64
 #define PHY_RETRIES		1000
 
 #define SKY2_EEPROM_MAGIC	0x9955aabb
@@ -131,6 +130,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436C) }, /* 88E8072 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */
+	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4373) }, /* 88E8075 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4381) }, /* 88E8059 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4382) }, /* 88E8079 */
@@ -4802,7 +4802,7 @@
 	 * 1) from device tree data
 	 * 2) from internal registers set by bootloader
 	 */
-	ret = of_get_mac_address(hw->pdev->dev.of_node, dev->dev_addr);
+	ret = of_get_ethdev_address(hw->pdev->dev.of_node, dev);
 	if (ret)
 		memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8,
 			      ETH_ALEN);
@@ -5073,7 +5073,7 @@
 		}
 	}
 
-	netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_WEIGHT);
+	netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_POLL_WEIGHT);
 
 	err = register_netdev(dev);
 	if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/marvell/sky2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/marvell/sky2.h
@@ -2195,7 +2195,7 @@
 	struct sk_buff	*skb;
 	dma_addr_t	data_addr;
 	DEFINE_DMA_UNMAP_LEN(data_size);
-	dma_addr_t	frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
+	dma_addr_t	frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT ?: 1];
 };
 
 enum flow_control {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -91,46 +91,53 @@
 	}
 
 	dev_err(eth->dev, "mdio: MDIO timeout\n");
-	return -1;
+	return -ETIMEDOUT;
 }
 
-static u32 _mtk_mdio_write(struct mtk_eth *eth, u32 phy_addr,
-			   u32 phy_register, u32 write_data)
+static int _mtk_mdio_write(struct mtk_eth *eth, u32 phy_addr, u32 phy_reg,
+			   u32 write_data)
 {
-	if (mtk_mdio_busy_wait(eth))
-		return -1;
+	int ret;
 
-	write_data &= 0xffff;
+	ret = mtk_mdio_busy_wait(eth);
+	if (ret < 0)
+		return ret;
 
-	mtk_w32(eth, PHY_IAC_ACCESS | PHY_IAC_START | PHY_IAC_WRITE |
-		(phy_register << PHY_IAC_REG_SHIFT) |
-		(phy_addr << PHY_IAC_ADDR_SHIFT) | write_data,
+	mtk_w32(eth, PHY_IAC_ACCESS |
+		     PHY_IAC_START_C22 |
+		     PHY_IAC_CMD_WRITE |
+		     PHY_IAC_REG(phy_reg) |
+		     PHY_IAC_ADDR(phy_addr) |
+		     PHY_IAC_DATA(write_data),
 		MTK_PHY_IAC);
 
-	if (mtk_mdio_busy_wait(eth))
-		return -1;
+	ret = mtk_mdio_busy_wait(eth);
+	if (ret < 0)
+		return ret;
 
 	return 0;
 }
 
-static u32 _mtk_mdio_read(struct mtk_eth *eth, int phy_addr, int phy_reg)
+static int _mtk_mdio_read(struct mtk_eth *eth, u32 phy_addr, u32 phy_reg)
 {
-	u32 d;
+	int ret;
 
-	if (mtk_mdio_busy_wait(eth))
-		return 0xffff;
+	ret = mtk_mdio_busy_wait(eth);
+	if (ret < 0)
+		return ret;
 
-	mtk_w32(eth, PHY_IAC_ACCESS | PHY_IAC_START | PHY_IAC_READ |
-		(phy_reg << PHY_IAC_REG_SHIFT) |
-		(phy_addr << PHY_IAC_ADDR_SHIFT),
+	mtk_w32(eth, PHY_IAC_ACCESS |
+		     PHY_IAC_START_C22 |
+		     PHY_IAC_CMD_C22_READ |
+		     PHY_IAC_REG(phy_reg) |
+		     PHY_IAC_ADDR(phy_addr),
 		MTK_PHY_IAC);
 
-	if (mtk_mdio_busy_wait(eth))
-		return 0xffff;
-
-	d = mtk_r32(eth, MTK_PHY_IAC) & 0xffff;
+	ret = mtk_mdio_busy_wait(eth);
+	if (ret < 0)
+		return ret;
 
-	return d;
+	return mtk_r32(eth, MTK_PHY_IAC) & PHY_IAC_DATA_MASK;
 }
 
 static int mtk_mdio_write(struct mii_bus *bus, int phy_addr,
@@ -216,8 +223,8 @@
 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
 					   phylink_config);
 	struct mtk_eth *eth = mac->hw;
-	u32 mcr_cur, mcr_new, sid, i;
-	int val, ge_mode, err;
+	int val, ge_mode, err = 0;
+	u32 sid, i;
 
 	/* MT76x8 has no hardware settings between for the MAC */
 	if (!MTK_HAS_CAPS(eth->soc->caps, MTK_SOC_MT7628) &&
@@ -352,16 +359,6 @@
 		return;
 	}
 
-	/* Setup gmac */
-	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
-	mcr_new = mcr_cur;
-	mcr_new |= MAC_MCR_IPG_CFG | MAC_MCR_FORCE_MODE |
-		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_LINK;
-
-	/* Only update control register when needed! */
-	if (mcr_new != mcr_cur)
-		mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
-
 	return;
 
 err_phy:
@@ -374,6 +371,26 @@
 		mac->id, phy_modes(state->interface), err);
 }
 
+static int mtk_mac_finish(struct phylink_config *config, unsigned int mode,
+			  phy_interface_t interface)
+{
+	struct mtk_mac *mac = container_of(config, struct mtk_mac,
+					   phylink_config);
+	u32 mcr_cur, mcr_new;
+
+	/* Setup gmac */
+	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
+	mcr_new = mcr_cur;
+	mcr_new |= MAC_MCR_IPG_CFG | MAC_MCR_FORCE_MODE |
+		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_RX_FIFO_CLR_DIS;
+
+	/* Only update control register when needed! */
+	if (mcr_new != mcr_cur)
+		mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
+
+	return 0;
+}
+
 static void mtk_mac_pcs_get_state(struct phylink_config *config,
 				  struct phylink_link_state *state)
 {
@@ -421,7 +438,7 @@
 					   phylink_config);
 	u32 mcr = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 
-	mcr &= ~(MAC_MCR_TX_EN | MAC_MCR_RX_EN);
+	mcr &= ~(MAC_MCR_TX_EN | MAC_MCR_RX_EN | MAC_MCR_FORCE_LINK);
 	mtk_w32(mac->hw, mcr, MTK_MAC_MCR(mac->id));
 }
 
@@ -459,7 +476,7 @@
 	if (rx_pause)
 		mcr |= MAC_MCR_FORCE_RX_FC;
 
-	mcr |= MAC_MCR_TX_EN | MAC_MCR_RX_EN;
+	mcr |= MAC_MCR_TX_EN | MAC_MCR_RX_EN | MAC_MCR_FORCE_LINK;
 	mtk_w32(mac->hw, mcr, MTK_MAC_MCR(mac->id));
 }
 
@@ -554,6 +571,7 @@
 	.mac_pcs_get_state = mtk_mac_pcs_get_state,
 	.mac_an_restart = mtk_mac_an_restart,
 	.mac_config = mtk_mac_config,
+	.mac_finish = mtk_mac_finish,
 	.mac_link_down = mtk_mac_link_down,
 	.mac_link_up = mtk_mac_link_up,
 };
@@ -813,6 +831,17 @@
 	return true;
 }
 
+static void *mtk_max_lro_buf_alloc(gfp_t gfp_mask)
+{
+	unsigned int size = mtk_max_frag_size(MTK_MAX_LRO_RX_LENGTH);
+	unsigned long data;
+
+	data = __get_free_pages(gfp_mask | __GFP_COMP | __GFP_NOWARN,
+				get_order(size));
+
+	return (void *)data;
+}
+
 /* the qdma core needs scratch memory to be setup */
 static int mtk_init_fq_dma(struct mtk_eth *eth)
 {
@@ -1304,7 +1333,10 @@
 			goto release_desc;
 
 		/* alloc new buffer */
-		new_data = napi_alloc_frag(ring->frag_size);
+		if (ring->frag_size <= PAGE_SIZE)
+			new_data = napi_alloc_frag(ring->frag_size);
+		else
+			new_data = mtk_max_lro_buf_alloc(GFP_ATOMIC);
 		if (unlikely(!new_data)) {
 			netdev->stats.rx_dropped++;
 			goto release_desc;
@@ -1718,7 +1750,10 @@
 		return -ENOMEM;
 
 	for (i = 0; i < rx_dma_size; i++) {
-		ring->data[i] = netdev_alloc_frag(ring->frag_size);
+		if (ring->frag_size <= PAGE_SIZE)
+			ring->data[i] = netdev_alloc_frag(ring->frag_size);
+		else
+			ring->data[i] = mtk_max_lro_buf_alloc(GFP_KERNEL);
 		if (!ring->data[i])
 			return -ENOMEM;
 	}
@@ -1984,6 +2019,9 @@
 	struct ethtool_rx_flow_spec *fsp =
 		(struct ethtool_rx_flow_spec *)&cmd->fs;
 
+	if (fsp->location >= ARRAY_SIZE(mac->hwlro_ip))
+		return -EINVAL;
+
 	/* only tcp dst ipv4 is meaningful, others are meaningless */
 	fsp->flow_type = TCP_V4_FLOW;
 	fsp->h_u.tcp_ip4_spec.ip4dst = ntohl(mac->hwlro_ip[fsp->location]);
@@ -2010,6 +2048,9 @@
 	int i;
 
 	for (i = 0; i < MTK_MAX_LRO_IP_CNT; i++) {
+		if (cnt == cmd->rule_cnt)
+			return -EMSGSIZE;
+
 		if (mac->hwlro_ip[i]) {
 			rule_locs[cnt] = i;
 			cnt++;
@@ -2300,8 +2341,10 @@
 		int err;
 
 		err = mtk_start_dma(eth);
-		if (err)
+		if (err) {
+			phylink_disconnect_phy(mac->phylink);
 			return err;
+		}
 
 		if (eth->soc->offload_version && mtk_ppe_start(&eth->ppe) == 0)
 			gdm_config = MTK_GDMA_TO_PPE;
@@ -2582,23 +2625,6 @@
 	return 0;
 }
 
-static int __init mtk_init(struct net_device *dev)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-	struct mtk_eth *eth = mac->hw;
-	int ret;
-
-	ret = of_get_mac_address(mac->of_node, dev->dev_addr);
-	if (ret) {
-		/* If the mac address is invalid, use random mac address */
-		eth_hw_addr_random(dev);
-		dev_err(eth->dev, "generated random MAC address %pM\n",
-			dev->dev_addr);
-	}
-
-	return 0;
-}
-
 static void mtk_uninit(struct net_device *dev)
 {
 	struct mtk_mac *mac = netdev_priv(dev);
@@ -2926,7 +2952,6 @@
 };
 
 static const struct net_device_ops mtk_netdev_ops = {
-	.ndo_init		= mtk_init,
 	.ndo_uninit		= mtk_uninit,
 	.ndo_open		= mtk_open,
 	.ndo_stop		= mtk_stop,
@@ -2980,6 +3005,17 @@
 	mac->hw = eth;
 	mac->of_node = np;
 
+	err = of_get_ethdev_address(mac->of_node, eth->netdev[id]);
+	if (err == -EPROBE_DEFER)
+		return err;
+
+	if (err) {
+		/* If the mac address is invalid, use random mac address */
+		eth_hw_addr_random(eth->netdev[id]);
+		dev_err(eth->dev, "generated random MAC address %pM\n",
+			eth->netdev[id]->dev_addr);
+	}
+
 	memset(mac->hwlro_ip, 0, sizeof(mac->hwlro_ip));
 	mac->hwlro_ip_cnt = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -341,11 +341,17 @@
 /* PHY Indirect Access Control registers */
 #define MTK_PHY_IAC		0x10004
 #define PHY_IAC_ACCESS		BIT(31)
-#define PHY_IAC_READ		BIT(19)
-#define PHY_IAC_WRITE		BIT(18)
-#define PHY_IAC_START		BIT(16)
-#define PHY_IAC_ADDR_SHIFT	20
-#define PHY_IAC_REG_SHIFT	25
+#define PHY_IAC_REG_MASK	GENMASK(29, 25)
+#define PHY_IAC_REG(x)		FIELD_PREP(PHY_IAC_REG_MASK, (x))
+#define PHY_IAC_ADDR_MASK	GENMASK(24, 20)
+#define PHY_IAC_ADDR(x)		FIELD_PREP(PHY_IAC_ADDR_MASK, (x))
+#define PHY_IAC_CMD_MASK	GENMASK(19, 18)
+#define PHY_IAC_CMD_WRITE	FIELD_PREP(PHY_IAC_CMD_MASK, 1)
+#define PHY_IAC_CMD_C22_READ	FIELD_PREP(PHY_IAC_CMD_MASK, 2)
+#define PHY_IAC_START_MASK	GENMASK(17, 16)
+#define PHY_IAC_START_C22	FIELD_PREP(PHY_IAC_START_MASK, 1)
+#define PHY_IAC_DATA_MASK	GENMASK(15, 0)
+#define PHY_IAC_DATA(x)		FIELD_PREP(PHY_IAC_DATA_MASK, (x))
 #define PHY_IAC_TIMEOUT		HZ
 
 #define MTK_MAC_MISC		0x1000c
@@ -363,6 +369,7 @@
 #define MAC_MCR_FORCE_MODE	BIT(15)
 #define MAC_MCR_TX_EN		BIT(14)
 #define MAC_MCR_RX_EN		BIT(13)
+#define MAC_MCR_RX_FIFO_CLR_DIS	BIT(12)
 #define MAC_MCR_BACKOFF_EN	BIT(9)
 #define MAC_MCR_BACKPR_EN	BIT(8)
 #define MAC_MCR_FORCE_RX_FC	BIT(5)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mediatek/mtk_ppe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mediatek/mtk_ppe.c
@@ -395,7 +395,7 @@
 	static const u8 skip[] = { 12, 25, 38, 51, 76, 89, 102 };
 	int i, k;
 
-	memset(ppe->foe_table, 0, MTK_PPE_ENTRIES * sizeof(ppe->foe_table));
+	memset(ppe->foe_table, 0, MTK_PPE_ENTRIES * sizeof(*ppe->foe_table));
 
 	if (!IS_ENABLED(CONFIG_SOC_MT7621))
 		return;
@@ -425,7 +425,7 @@
 			 MTK_PPE_KEEPALIVE_DISABLE) |
 	      FIELD_PREP(MTK_PPE_TB_CFG_HASH_MODE, 1) |
 	      FIELD_PREP(MTK_PPE_TB_CFG_SCAN_MODE,
-			 MTK_PPE_SCAN_MODE_KEEPALIVE_AGE) |
+			 MTK_PPE_SCAN_MODE_CHECK_AGE) |
 	      FIELD_PREP(MTK_PPE_TB_CFG_ENTRY_NUM,
 			 MTK_PPE_ENTRIES_SHIFT);
 	ppe_w32(ppe, MTK_PPE_TB_CFG, val);
@@ -493,17 +493,21 @@
 
 	mtk_ppe_cache_enable(ppe, false);
 
-	/* disable offload engine */
-	ppe_clear(ppe, MTK_PPE_GLO_CFG, MTK_PPE_GLO_CFG_EN);
-	ppe_w32(ppe, MTK_PPE_FLOW_CFG, 0);
-
 	/* disable aging */
 	val = MTK_PPE_TB_CFG_AGE_NON_L4 |
 	      MTK_PPE_TB_CFG_AGE_UNBIND |
 	      MTK_PPE_TB_CFG_AGE_TCP |
 	      MTK_PPE_TB_CFG_AGE_UDP |
-	      MTK_PPE_TB_CFG_AGE_TCP_FIN;
+	      MTK_PPE_TB_CFG_AGE_TCP_FIN |
+		  MTK_PPE_TB_CFG_SCAN_MODE;
 	ppe_clear(ppe, MTK_PPE_TB_CFG, val);
 
-	return mtk_ppe_wait_busy(ppe);
+	if (mtk_ppe_wait_busy(ppe))
+		return -ETIMEDOUT;
+
+	/* disable offload engine */
+	ppe_clear(ppe, MTK_PPE_GLO_CFG, MTK_PPE_GLO_CFG_EN);
+	ppe_w32(ppe, MTK_PPE_FLOW_CFG, 0);
+
+	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mediatek/mtk_ppe_offload.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mediatek/mtk_ppe_offload.c
@@ -462,6 +462,7 @@
 		if (IS_ERR(block_cb))
 			return PTR_ERR(block_cb);
 
+		flow_block_cb_incref(block_cb);
 		flow_block_cb_add(block_cb, f);
 		list_add_tail(&block_cb->driver_list, &block_cb_list);
 		return 0;
@@ -470,7 +471,7 @@
 		if (!block_cb)
 			return -ENOENT;
 
-		if (flow_block_cb_decref(block_cb)) {
+		if (!flow_block_cb_decref(block_cb)) {
 			flow_block_cb_remove(block_cb, f);
 			list_del(&block_cb->driver_list);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mediatek/mtk_sgmii.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mediatek/mtk_sgmii.c
@@ -26,6 +26,7 @@
 			break;
 
 		ss->regmap[i] = syscon_node_to_regmap(np);
+		of_node_put(np);
 		if (IS_ERR(ss->regmap[i]))
 			return PTR_ERR(ss->regmap[i]);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mediatek/mtk_star_emac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mediatek/mtk_star_emac.c
@@ -30,7 +30,6 @@
 #define MTK_STAR_WAIT_TIMEOUT			300
 #define MTK_STAR_MAX_FRAME_SIZE			1514
 #define MTK_STAR_SKB_ALIGNMENT			16
-#define MTK_STAR_NAPI_WEIGHT			64
 #define MTK_STAR_HASHTABLE_MC_LIMIT		256
 #define MTK_STAR_HASHTABLE_SIZE_MAX		512
 
@@ -523,7 +522,7 @@
 static void mtk_star_set_mac_addr(struct net_device *ndev)
 {
 	struct mtk_star_priv *priv = netdev_priv(ndev);
-	u8 *mac_addr = ndev->dev_addr;
+	const u8 *mac_addr = ndev->dev_addr;
 	unsigned int high, low;
 
 	high = mac_addr[0] << 8 | mac_addr[1] << 0;
@@ -1447,6 +1446,7 @@
 {
 	struct device_node *of_node;
 	struct mtk_star_priv *priv;
+	struct phy_device *phydev;
 	struct net_device *ndev;
 	struct device *dev;
 	void __iomem *base;
@@ -1551,7 +1551,13 @@
 	ndev->netdev_ops = &mtk_star_netdev_ops;
 	ndev->ethtool_ops = &mtk_star_ethtool_ops;
 
-	netif_napi_add(ndev, &priv->napi, mtk_star_poll, MTK_STAR_NAPI_WEIGHT);
+	netif_napi_add(ndev, &priv->napi, mtk_star_poll, NAPI_POLL_WEIGHT);
+
+	phydev = of_phy_find_device(priv->phy_node);
+	if (phydev) {
+		phydev->mac_managed_pm = true;
+		put_device(&phydev->mdio.dev);
+	}
 
 	return devm_register_netdev(dev, ndev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
@@ -663,7 +663,7 @@
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_1000BASE_T, SPEED_1000,
 				       ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_1000BASE_CX_SGMII, SPEED_1000,
-				       ETHTOOL_LINK_MODE_1000baseKX_Full_BIT);
+				       ETHTOOL_LINK_MODE_1000baseX_Full_BIT);
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_1000BASE_KX, SPEED_1000,
 				       ETHTOOL_LINK_MODE_1000baseKX_Full_BIT);
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_10GBASE_T, SPEED_10000,
@@ -675,9 +675,9 @@
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_10GBASE_KR, SPEED_10000,
 				       ETHTOOL_LINK_MODE_10000baseKR_Full_BIT);
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_10GBASE_CR, SPEED_10000,
-				       ETHTOOL_LINK_MODE_10000baseKR_Full_BIT);
+				       ETHTOOL_LINK_MODE_10000baseCR_Full_BIT);
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_10GBASE_SR, SPEED_10000,
-				       ETHTOOL_LINK_MODE_10000baseKR_Full_BIT);
+				       ETHTOOL_LINK_MODE_10000baseSR_Full_BIT);
 	MLX4_BUILD_PTYS2ETHTOOL_CONFIG(MLX4_20GBASE_KR2, SPEED_20000,
 				       ETHTOOL_LINK_MODE_20000baseMLD2_Full_BIT,
 				       ETHTOOL_LINK_MODE_20000baseKR2_Full_BIT);
@@ -2103,7 +2103,7 @@
 			en_err(priv,
 			       "mlx4_get_module_info i(%d) offset(%d) bytes_to_read(%d) - FAILED (0x%x)\n",
 			       i, offset, ee->len - i, ret);
-			return 0;
+			return ret;
 		}
 
 		i += ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -2286,9 +2286,14 @@
 				bool carry_xdp_prog)
 {
 	struct bpf_prog *xdp_prog;
-	int i, t;
+	int i, t, ret;
 
-	mlx4_en_copy_priv(tmp, priv, prof);
+	ret = mlx4_en_copy_priv(tmp, priv, prof);
+	if (ret) {
+		en_warn(priv, "%s: mlx4_en_copy_priv() failed, return\n",
+			__func__);
+		return ret;
+	}
 
 	if (mlx4_en_alloc_resources(tmp)) {
 		en_warn(priv,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx4/qp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx4/qp.c
@@ -697,7 +697,8 @@
 			err = mlx4_bitmap_init(*bitmap + k, 1,
 					       MLX4_QP_TABLE_RAW_ETH_SIZE - 1, 0,
 					       0);
-			mlx4_bitmap_alloc_range(*bitmap + k, 1, 1, 0);
+			if (!err)
+				mlx4_bitmap_alloc_range(*bitmap + k, 1, 1, 0);
 		}
 
 		if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/Makefile
@@ -45,7 +45,7 @@
 					esw/indir_table.o en/tc_tun_encap.o \
 					en/tc_tun_vxlan.o en/tc_tun_gre.o en/tc_tun_geneve.o \
 					en/tc_tun_mplsoudp.o diag/en_tc_tracepoint.o \
-					en/tc/post_act.o
+					en/tc/post_act.o en/tc/int_port.o
 mlx5_core-$(CONFIG_MLX5_TC_CT)	     += en/tc_ct.o
 mlx5_core-$(CONFIG_MLX5_TC_SAMPLE)   += en/tc/sample.o
 
@@ -94,8 +94,10 @@
 					steering/dr_icm_pool.o steering/dr_buddy.o \
 					steering/dr_ste.o steering/dr_send.o \
 					steering/dr_ste_v0.o steering/dr_ste_v1.o \
+					steering/dr_ste_v2.o \
 					steering/dr_cmd.o steering/dr_fw.o \
-					steering/dr_action.o steering/fs_dr.o
+					steering/dr_action.o steering/fs_dr.o \
+					steering/dr_dbg.o
 #
 # SF device
 #
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/cmd.c
@@ -114,15 +114,18 @@
 	return token;
 }
 
-static int cmd_alloc_index(struct mlx5_cmd *cmd)
+static int cmd_alloc_index(struct mlx5_cmd *cmd, struct mlx5_cmd_work_ent *ent)
 {
 	unsigned long flags;
 	int ret;
 
 	spin_lock_irqsave(&cmd->alloc_lock, flags);
 	ret = find_first_bit(&cmd->bitmask, cmd->max_reg_cmds);
-	if (ret < cmd->max_reg_cmds)
+	if (ret < cmd->max_reg_cmds) {
 		clear_bit(ret, &cmd->bitmask);
+		ent->idx = ret;
+		cmd->ent_arr[ent->idx] = ent;
+	}
 	spin_unlock_irqrestore(&cmd->alloc_lock, flags);
 
 	return ret < cmd->max_reg_cmds ? ret : -ENOMEM;
@@ -130,11 +133,8 @@
 
 static void cmd_free_index(struct mlx5_cmd *cmd, int idx)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&cmd->alloc_lock, flags);
+	lockdep_assert_held(&cmd->alloc_lock);
 	set_bit(idx, &cmd->bitmask);
-	spin_unlock_irqrestore(&cmd->alloc_lock, flags);
 }
 
 static void cmd_ent_get(struct mlx5_cmd_work_ent *ent)
@@ -144,13 +144,21 @@
 
 static void cmd_ent_put(struct mlx5_cmd_work_ent *ent)
 {
+	struct mlx5_cmd *cmd = ent->cmd;
+	unsigned long flags;
+
+	spin_lock_irqsave(&cmd->alloc_lock, flags);
 	if (!refcount_dec_and_test(&ent->refcnt))
-		return;
+		goto out;
 
-	if (ent->idx >= 0)
-		cmd_free_index(ent->cmd, ent->idx);
+	if (ent->idx >= 0) {
+		cmd_free_index(cmd, ent->idx);
+		up(ent->page_queue ? &cmd->pages_sem : &cmd->sem);
+	}
 
 	cmd_free_ent(ent);
+out:
+	spin_unlock_irqrestore(&cmd->alloc_lock, flags);
 }
 
 static struct mlx5_cmd_layout *get_inst(struct mlx5_cmd *cmd, int idx)
@@ -334,6 +342,9 @@
 	case MLX5_CMD_OP_PAGE_FAULT_RESUME:
 	case MLX5_CMD_OP_QUERY_ESW_FUNCTIONS:
 	case MLX5_CMD_OP_DEALLOC_SF:
+	case MLX5_CMD_OP_DESTROY_UCTX:
+	case MLX5_CMD_OP_DESTROY_UMEM:
+	case MLX5_CMD_OP_MODIFY_RQT:
 		return MLX5_CMD_STAT_OK;
 
 	case MLX5_CMD_OP_QUERY_HCA_CAP:
@@ -439,7 +450,6 @@
 	case MLX5_CMD_OP_MODIFY_TIS:
 	case MLX5_CMD_OP_QUERY_TIS:
 	case MLX5_CMD_OP_CREATE_RQT:
-	case MLX5_CMD_OP_MODIFY_RQT:
 	case MLX5_CMD_OP_QUERY_RQT:
 
 	case MLX5_CMD_OP_CREATE_FLOW_TABLE:
@@ -459,9 +469,7 @@
 	case MLX5_CMD_OP_MODIFY_GENERAL_OBJECT:
 	case MLX5_CMD_OP_QUERY_GENERAL_OBJECT:
 	case MLX5_CMD_OP_CREATE_UCTX:
-	case MLX5_CMD_OP_DESTROY_UCTX:
 	case MLX5_CMD_OP_CREATE_UMEM:
-	case MLX5_CMD_OP_DESTROY_UMEM:
 	case MLX5_CMD_OP_ALLOC_MEMIC:
 	case MLX5_CMD_OP_MODIFY_XRQ:
 	case MLX5_CMD_OP_RELEASE_XRQ_ERROR:
@@ -895,25 +903,6 @@
 	return cmd->allowed_opcode == opcode;
 }
 
-static int cmd_alloc_index_retry(struct mlx5_cmd *cmd)
-{
-	unsigned long alloc_end = jiffies + msecs_to_jiffies(1000);
-	int idx;
-
-retry:
-	idx = cmd_alloc_index(cmd);
-	if (idx < 0 && time_before(jiffies, alloc_end)) {
-		/* Index allocation can fail on heavy load of commands. This is a temporary
-		 * situation as the current command already holds the semaphore, meaning that
-		 * another command completion is being handled and it is expected to release
-		 * the entry index soon.
-		 */
-		cpu_relax();
-		goto retry;
-	}
-	return idx;
-}
-
 bool mlx5_cmd_is_down(struct mlx5_core_dev *dev)
 {
 	return pci_channel_offline(dev->pdev) ||
@@ -938,7 +927,7 @@
 	sem = ent->page_queue ? &cmd->pages_sem : &cmd->sem;
 	down(sem);
 	if (!ent->page_queue) {
-		alloc_ret = cmd_alloc_index_retry(cmd);
+		alloc_ret = cmd_alloc_index(cmd, ent);
 		if (alloc_ret < 0) {
 			mlx5_core_err_rl(dev, "failed to allocate command entry\n");
 			if (ent->callback) {
@@ -953,15 +942,14 @@
 			up(sem);
 			return;
 		}
-		ent->idx = alloc_ret;
 	} else {
 		ent->idx = cmd->max_reg_cmds;
 		spin_lock_irqsave(&cmd->alloc_lock, flags);
 		clear_bit(ent->idx, &cmd->bitmask);
+		cmd->ent_arr[ent->idx] = ent;
 		spin_unlock_irqrestore(&cmd->alloc_lock, flags);
 	}
 
-	cmd->ent_arr[ent->idx] = ent;
 	lay = get_inst(cmd, ent->idx);
 	ent->lay = lay;
 	memset(lay, 0, sizeof(*lay));
@@ -985,6 +973,7 @@
 		cmd_ent_get(ent);
 	set_bit(MLX5_CMD_ENT_STATE_PENDING_COMP, &ent->state);
 
+	cmd_ent_get(ent); /* for the _real_ FW event on completion */
 	/* Skip sending command to fw if internal error */
 	if (mlx5_cmd_is_down(dev) || !opcode_allowed(&dev->cmd, ent->op)) {
 		u8 status = 0;
@@ -998,7 +987,6 @@
 		return;
 	}
 
-	cmd_ent_get(ent); /* for the _real_ FW event on completion */
 	/* ring doorbell after the descriptor is valid */
 	mlx5_core_dbg(dev, "writing 0x%x to command doorbell\n", 1 << ent->idx);
 	wmb();
@@ -1448,8 +1436,8 @@
 		return -EFAULT;
 
 	err = sscanf(outlen_str, "%d", &outlen);
-	if (err < 0)
-		return err;
+	if (err != 1)
+		return -EINVAL;
 
 	ptr = kzalloc(outlen, GFP_KERNEL);
 	if (!ptr)
@@ -1547,6 +1535,9 @@
 	dev = container_of(cmd, struct mlx5_core_dev, cmd);
 	eqe = data;
 
+	if (dev->state == MLX5_DEVICE_STATE_INTERNAL_ERROR)
+		return NOTIFY_DONE;
+
 	mlx5_cmd_comp_handler(dev, be32_to_cpu(eqe->data.cmd.vector), false);
 
 	return NOTIFY_OK;
@@ -1594,8 +1585,6 @@
 	vector = vec & 0xffffffff;
 	for (i = 0; i < (1 << cmd->log_sz); i++) {
 		if (test_bit(i, &vector)) {
-			struct semaphore *sem;
-
 			ent = cmd->ent_arr[i];
 
 			/* if we already completed the command, ignore it */
@@ -1614,14 +1603,10 @@
 				cmd_ent_put(ent); /* timeout work was canceled */
 
 			if (!forced || /* Real FW completion */
-			    pci_channel_offline(dev->pdev) || /* FW is inaccessible */
-			    dev->state == MLX5_DEVICE_STATE_INTERNAL_ERROR)
+			     mlx5_cmd_is_down(dev) || /* No real FW completion is expected */
+			     !opcode_allowed(cmd, ent->op))
 				cmd_ent_put(ent);
 
-			if (ent->page_queue)
-				sem = &cmd->pages_sem;
-			else
-				sem = &cmd->sem;
 			ent->ts2 = ktime_get_ns();
 			memcpy(ent->out->first.data, ent->lay->out, sizeof(ent->lay->out));
 			dump_command(dev, ent, 0);
@@ -1675,7 +1660,6 @@
 				 */
 				complete(&ent->done);
 			}
-			up(sem);
 		}
 	}
 }
@@ -1720,12 +1704,17 @@
 	struct mlx5_cmd *cmd = &dev->cmd;
 	int i;
 
-	for (i = 0; i < cmd->max_reg_cmds; i++)
-		while (down_trylock(&cmd->sem))
+	for (i = 0; i < cmd->max_reg_cmds; i++) {
+		while (down_trylock(&cmd->sem)) {
 			mlx5_cmd_trigger_completions(dev);
+			cond_resched();
+		}
+	}
 
-	while (down_trylock(&cmd->pages_sem))
+	while (down_trylock(&cmd->pages_sem)) {
 		mlx5_cmd_trigger_completions(dev);
+		cond_resched();
+	}
 
 	/* Unlock cmdif */
 	up(&cmd->pages_sem);
@@ -1886,7 +1875,7 @@
 	ctx->dev = dev;
 	/* Starts at 1 to avoid doing wake_up if we are not cleaning up */
 	atomic_set(&ctx->num_inflight, 1);
-	init_waitqueue_head(&ctx->wait);
+	init_completion(&ctx->inflight_done);
 }
 EXPORT_SYMBOL(mlx5_cmd_init_async_ctx);
 
@@ -1900,8 +1889,8 @@
  */
 void mlx5_cmd_cleanup_async_ctx(struct mlx5_async_ctx *ctx)
 {
-	atomic_dec(&ctx->num_inflight);
-	wait_event(ctx->wait, atomic_read(&ctx->num_inflight) == 0);
+	if (!atomic_dec_and_test(&ctx->num_inflight))
+		wait_for_completion(&ctx->inflight_done);
 }
 EXPORT_SYMBOL(mlx5_cmd_cleanup_async_ctx);
 
@@ -1912,7 +1901,7 @@
 
 	work->user_callback(status, work);
 	if (atomic_dec_and_test(&ctx->num_inflight))
-		wake_up(&ctx->wait);
+		complete(&ctx->inflight_done);
 }
 
 int mlx5_cmd_exec_cb(struct mlx5_async_ctx *ctx, void *in, int in_size,
@@ -1928,7 +1917,7 @@
 	ret = cmd_exec(ctx->dev, in, in_size, out, out_size,
 		       mlx5_cmd_exec_cb_handler, work, false);
 	if (ret && atomic_dec_and_test(&ctx->num_inflight))
-		wake_up(&ctx->wait);
+		complete(&ctx->inflight_done);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/cq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/cq.c
@@ -164,13 +164,14 @@
 	MLX5_SET(destroy_cq_in, in, cqn, cq->cqn);
 	MLX5_SET(destroy_cq_in, in, uid, cq->uid);
 	err = mlx5_cmd_exec_in(dev, destroy_cq, in);
+	if (err)
+		return err;
 
 	synchronize_irq(cq->irqn);
-
 	mlx5_cq_put(cq);
 	wait_for_completion(&cq->free);
 
-	return err;
+	return 0;
 }
 EXPORT_SYMBOL(mlx5_core_destroy_cq);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/debugfs.c
@@ -507,6 +507,8 @@
 	if (!mlx5_debugfs_root)
 		return;
 
-	if (cq->dbg)
+	if (cq->dbg) {
 		rem_res_tree(cq->dbg);
+		cq->dbg = NULL;
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/dev.c
@@ -544,12 +544,9 @@
 		     PCI_SLOT(dev->pdev->devfn));
 }
 
-static int next_phys_dev(struct device *dev, const void *data)
+static int _next_phys_dev(struct mlx5_core_dev *mdev,
+			  const struct mlx5_core_dev *curr)
 {
-	struct mlx5_adev *madev = container_of(dev, struct mlx5_adev, adev.dev);
-	struct mlx5_core_dev *mdev = madev->mdev;
-	const struct mlx5_core_dev *curr = data;
-
 	if (!mlx5_core_is_pf(mdev))
 		return 0;
 
@@ -562,22 +559,69 @@
 	return 1;
 }
 
-/* Must be called with intf_mutex held */
-struct mlx5_core_dev *mlx5_get_next_phys_dev(struct mlx5_core_dev *dev)
+static void *pci_get_other_drvdata(struct device *this, struct device *other)
 {
-	struct auxiliary_device *adev;
-	struct mlx5_adev *madev;
+	if (this->driver != other->driver)
+		return NULL;
+
+	return pci_get_drvdata(to_pci_dev(other));
+}
+
+static int next_phys_dev(struct device *dev, const void *data)
+{
+	struct mlx5_core_dev *mdev, *this = (struct mlx5_core_dev *)data;
+
+	mdev = pci_get_other_drvdata(this->device, dev);
+	if (!mdev)
+		return 0;
+
+	return _next_phys_dev(mdev, data);
+}
+
+static int next_phys_dev_lag(struct device *dev, const void *data)
+{
+	struct mlx5_core_dev *mdev, *this = (struct mlx5_core_dev *)data;
+
+	mdev = pci_get_other_drvdata(this->device, dev);
+	if (!mdev)
+		return 0;
+
+	if (!MLX5_CAP_GEN(mdev, vport_group_manager) ||
+	    !MLX5_CAP_GEN(mdev, lag_master) ||
+	    MLX5_CAP_GEN(mdev, num_lag_ports) != MLX5_MAX_PORTS)
+		return 0;
+
+	return _next_phys_dev(mdev, data);
+}
+
+static struct mlx5_core_dev *mlx5_get_next_dev(struct mlx5_core_dev *dev,
+					       int (*match)(struct device *dev, const void *data))
+{
+	struct device *next;
 
 	if (!mlx5_core_is_pf(dev))
 		return NULL;
 
-	adev = auxiliary_find_device(NULL, dev, &next_phys_dev);
-	if (!adev)
+	next = bus_find_device(&pci_bus_type, NULL, dev, match);
+	if (!next)
 		return NULL;
 
-	madev = container_of(adev, struct mlx5_adev, adev);
-	put_device(&adev->dev);
-	return madev->mdev;
+	put_device(next);
+	return pci_get_drvdata(to_pci_dev(next));
+}
+
+/* Must be called with intf_mutex held */
+struct mlx5_core_dev *mlx5_get_next_phys_dev(struct mlx5_core_dev *dev)
+{
+	lockdep_assert_held(&mlx5_intf_mutex);
+	return mlx5_get_next_dev(dev, &next_phys_dev);
+}
+
+/* Must be called with intf_mutex held */
+struct mlx5_core_dev *mlx5_get_next_phys_dev_lag(struct mlx5_core_dev *dev)
+{
+	lockdep_assert_held(&mlx5_intf_mutex);
+	return mlx5_get_next_dev(dev, &next_phys_dev_lag);
 }
 
 void mlx5_dev_list_lock(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/devlink.c
@@ -625,7 +625,6 @@
 	devlink_param_driverinit_value_set(devlink,
 					   DEVLINK_PARAM_GENERIC_ID_ENABLE_ETH,
 					   value);
-	devlink_param_publish(devlink, &enable_eth_param);
 	return 0;
 }
 
@@ -636,7 +635,6 @@
 	if (!mlx5_eth_supported(dev))
 		return;
 
-	devlink_param_unpublish(devlink, &enable_eth_param);
 	devlink_param_unregister(devlink, &enable_eth_param);
 }
 
@@ -672,7 +670,6 @@
 	devlink_param_driverinit_value_set(devlink,
 					   DEVLINK_PARAM_GENERIC_ID_ENABLE_RDMA,
 					   value);
-	devlink_param_publish(devlink, &enable_rdma_param);
 	return 0;
 }
 
@@ -681,7 +678,6 @@
 	if (!IS_ENABLED(CONFIG_MLX5_INFINIBAND))
 		return;
 
-	devlink_param_unpublish(devlink, &enable_rdma_param);
 	devlink_param_unregister(devlink, &enable_rdma_param);
 }
 
@@ -706,7 +702,6 @@
 	devlink_param_driverinit_value_set(devlink,
 					   DEVLINK_PARAM_GENERIC_ID_ENABLE_VNET,
 					   value);
-	devlink_param_publish(devlink, &enable_rdma_param);
 	return 0;
 }
 
@@ -717,7 +712,6 @@
 	if (!mlx5_vnet_supported(dev))
 		return;
 
-	devlink_param_unpublish(devlink, &enable_vnet_param);
 	devlink_param_unregister(devlink, &enable_vnet_param);
 }
 
@@ -808,7 +802,6 @@
 	if (err)
 		goto params_reg_err;
 	mlx5_devlink_set_params_init_values(devlink);
-	devlink_params_publish(devlink);
 
 	err = mlx5_devlink_auxdev_params_register(devlink);
 	if (err)
@@ -818,6 +811,7 @@
 	if (err)
 		goto traps_reg_err;
 
+	devlink_params_publish(devlink);
 	return 0;
 
 traps_reg_err:
@@ -832,9 +826,9 @@
 
 void mlx5_devlink_unregister(struct devlink *devlink)
 {
+	devlink_params_unpublish(devlink);
 	mlx5_devlink_traps_unregister(devlink);
 	mlx5_devlink_auxdev_params_unregister(devlink);
-	devlink_params_unpublish(devlink);
 	devlink_params_unregister(devlink, mlx5_devlink_params,
 				  ARRAY_SIZE(mlx5_devlink_params));
 	devlink_unregister(devlink);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/diag/fs_tracepoint.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/diag/fs_tracepoint.c
@@ -235,6 +235,9 @@
 	const char *ret = trace_seq_buffer_ptr(p);
 
 	switch (dst->type) {
+	case MLX5_FLOW_DESTINATION_TYPE_UPLINK:
+		trace_seq_printf(p, "uplink\n");
+		break;
 	case MLX5_FLOW_DESTINATION_TYPE_VPORT:
 		trace_seq_printf(p, "vport=%u\n", dst->vport.num);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c
@@ -64,6 +64,7 @@
 			MLX5_GET(mtrc_cap, out, num_string_trace);
 	tracer->str_db.num_string_db = MLX5_GET(mtrc_cap, out, num_string_db);
 	tracer->owner = !!MLX5_GET(mtrc_cap, out, trace_owner);
+	tracer->str_db.loaded = false;
 
 	for (i = 0; i < tracer->str_db.num_string_db; i++) {
 		mtrc_cap_sp = MLX5_ADDR_OF(mtrc_cap, out, string_db_param[i]);
@@ -482,7 +483,7 @@
 				(u64)timestamp_low;
 		break;
 	default:
-		if (tracer_event->event_id >= tracer->str_db.first_string_trace ||
+		if (tracer_event->event_id >= tracer->str_db.first_string_trace &&
 		    tracer_event->event_id <= tracer->str_db.first_string_trace +
 					      tracer->str_db.num_string_trace) {
 			tracer_event->type = TRACER_EVENT_TYPE_STRING;
@@ -602,7 +603,7 @@
 	} else {
 		cur_string = mlx5_tracer_message_get(tracer, tracer_event);
 		if (!cur_string) {
-			pr_debug("%s Got string event for unknown string tdsm: %d\n",
+			pr_debug("%s Got string event for unknown string tmsn: %d\n",
 				 __func__, tracer_event->string_event.tmsn);
 			return -1;
 		}
@@ -638,7 +639,7 @@
 			trace_timestamp = (timestamp_event.timestamp & MASK_52_7) |
 					  (str_frmt->timestamp & MASK_6_0);
 		else
-			trace_timestamp = ((timestamp_event.timestamp & MASK_52_7) - 1) |
+			trace_timestamp = ((timestamp_event.timestamp - 1) & MASK_52_7) |
 					  (str_frmt->timestamp & MASK_6_0);
 
 		mlx5_tracer_print_trace(str_frmt, dev, trace_timestamp);
@@ -675,6 +676,9 @@
 	if (!tracer->owner)
 		return;
 
+	if (unlikely(!tracer->str_db.loaded))
+		goto arm;
+
 	block_count = tracer->buff.size / TRACER_BLOCK_SIZE_BYTE;
 	start_offset = tracer->buff.consumer_index * TRACER_BLOCK_SIZE_BYTE;
 
@@ -687,7 +691,7 @@
 
 	while (block_timestamp > tracer->last_timestamp) {
 		/* Check block override if it's not the first block */
-		if (!tracer->last_timestamp) {
+		if (tracer->last_timestamp) {
 			u64 *ts_event;
 			/* To avoid block override be the HW in case of buffer
 			 * wraparound, the time stamp of the previous block
@@ -732,6 +736,7 @@
 						      &tmp_trace_block[TRACES_PER_BLOCK - 1]);
 	}
 
+arm:
 	mlx5_fw_tracer_arm(dev);
 }
 
@@ -752,6 +757,7 @@
 	if (err)
 		mlx5_core_warn(dev, "FWTracer: Failed to set tracer configurations %d\n", err);
 
+	tracer->buff.consumer_index = 0;
 	return err;
 }
 
@@ -815,8 +821,7 @@
 
 	mlx5_core_dbg(tracer->dev, "FWTracer: ownership changed, current=(%d)\n", tracer->owner);
 	if (tracer->owner) {
-		tracer->owner = false;
-		tracer->buff.consumer_index = 0;
+		mlx5_fw_tracer_ownership_acquire(tracer);
 		return;
 	}
 
@@ -1137,8 +1142,7 @@
 		queue_work(tracer->work_queue, &tracer->ownership_change_work);
 		break;
 	case MLX5_TRACER_SUBTYPE_TRACES_AVAILABLE:
-		if (likely(tracer->str_db.loaded))
-			queue_work(tracer->work_queue, &tracer->handle_traces_work);
+		queue_work(tracer->work_queue, &tracer->handle_traces_work);
 		break;
 	default:
 		mlx5_core_dbg(dev, "FWTracer: Event with unrecognized subtype: sub_type %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/diag/rsc_dump.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/diag/rsc_dump.c
@@ -31,6 +31,7 @@
 struct mlx5_rsc_dump {
 	u32 pdn;
 	struct mlx5_core_mkey mkey;
+	u32 number_of_menu_items;
 	u16 fw_segment_type[MLX5_SGMT_TYPE_NUM];
 };
 
@@ -50,21 +51,37 @@
 	return -EINVAL;
 }
 
-static void mlx5_rsc_dump_read_menu_sgmt(struct mlx5_rsc_dump *rsc_dump, struct page *page)
+#define MLX5_RSC_DUMP_MENU_HEADER_SIZE (MLX5_ST_SZ_BYTES(resource_dump_info_segment) + \
+					MLX5_ST_SZ_BYTES(resource_dump_command_segment) + \
+					MLX5_ST_SZ_BYTES(resource_dump_menu_segment))
+
+static int mlx5_rsc_dump_read_menu_sgmt(struct mlx5_rsc_dump *rsc_dump, struct page *page,
+					int read_size, int start_idx)
 {
 	void *data = page_address(page);
 	enum mlx5_sgmt_type sgmt_idx;
 	int num_of_items;
 	char *sgmt_name;
 	void *member;
+	int size = 0;
 	void *menu;
 	int i;
 
-	menu = MLX5_ADDR_OF(menu_resource_dump_response, data, menu);
-	num_of_items = MLX5_GET(resource_dump_menu_segment, menu, num_of_records);
+	if (!start_idx) {
+		menu = MLX5_ADDR_OF(menu_resource_dump_response, data, menu);
+		rsc_dump->number_of_menu_items = MLX5_GET(resource_dump_menu_segment, menu,
+							  num_of_records);
+		size = MLX5_RSC_DUMP_MENU_HEADER_SIZE;
+		data += size;
+	}
+	num_of_items = rsc_dump->number_of_menu_items;
+
+	for (i = 0; start_idx + i < num_of_items; i++) {
+		size += MLX5_ST_SZ_BYTES(resource_dump_menu_record);
+		if (size >= read_size)
+			return start_idx + i;
 
-	for (i = 0; i < num_of_items; i++) {
-		member = MLX5_ADDR_OF(resource_dump_menu_segment, menu, record[i]);
+		member = data + MLX5_ST_SZ_BYTES(resource_dump_menu_record) * i;
 		sgmt_name =  MLX5_ADDR_OF(resource_dump_menu_record, member, segment_name);
 		sgmt_idx = mlx5_rsc_dump_sgmt_get_by_name(sgmt_name);
 		if (sgmt_idx == -EINVAL)
@@ -72,6 +89,7 @@
 		rsc_dump->fw_segment_type[sgmt_idx] = MLX5_GET(resource_dump_menu_record,
 							       member, segment_type);
 	}
+	return 0;
 }
 
 static int mlx5_rsc_dump_trigger(struct mlx5_core_dev *dev, struct mlx5_rsc_dump_cmd *cmd,
@@ -168,6 +186,7 @@
 	struct mlx5_rsc_dump_cmd *cmd = NULL;
 	struct mlx5_rsc_key key = {};
 	struct page *page;
+	int start_idx = 0;
 	int size;
 	int err;
 
@@ -189,7 +208,7 @@
 		if (err < 0)
 			goto destroy_cmd;
 
-		mlx5_rsc_dump_read_menu_sgmt(dev->rsc_dump, page);
+		start_idx = mlx5_rsc_dump_read_menu_sgmt(dev->rsc_dump, page, size, start_idx);
 
 	} while (err > 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en.h
@@ -103,7 +103,7 @@
 #define MLX5E_REQUIRED_WQE_MTTS		(MLX5_ALIGN_MTTS(MLX5_MPWRQ_PAGES_PER_WQE + 1))
 #define MLX5E_REQUIRED_MTTS(wqes)	(wqes * MLX5E_REQUIRED_WQE_MTTS)
 #define MLX5E_MAX_RQ_NUM_MTTS	\
-	((1 << 16) * 2) /* So that MLX5_MTT_OCTW(num_mtts) fits into u16 */
+	(ALIGN_DOWN(U16_MAX, 4) * 2) /* So that MLX5_MTT_OCTW(num_mtts) fits into u16 */
 #define MLX5E_ORDER2_MAX_PACKET_MTU (order_base_2(10 * 1024))
 #define MLX5E_PARAMS_MAXIMUM_LOG_RQ_SIZE_MPW	\
 		(ilog2(MLX5E_MAX_RQ_NUM_MTTS / MLX5E_REQUIRED_WQE_MTTS))
@@ -244,6 +244,17 @@
 
 #define MLX5E_GET_PFLAG(params, pflag) (!!((params)->pflags & (BIT(pflag))))
 
+enum packet_merge {
+	MLX5E_PACKET_MERGE_NONE,
+	MLX5E_PACKET_MERGE_LRO,
+	MLX5E_PACKET_MERGE_SHAMPO,
+};
+
+struct mlx5e_packet_merge_param {
+	enum packet_merge type;
+	u32 timeout;
+};
+
 struct mlx5e_params {
 	u8  log_sq_size;
 	u8  rq_wq_type;
@@ -258,13 +269,12 @@
 	bool tunneled_offload_en;
 	struct dim_cq_moder rx_cq_moderation;
 	struct dim_cq_moder tx_cq_moderation;
-	bool lro_en;
+	struct mlx5e_packet_merge_param packet_merge;
 	u8  tx_min_inline_mode;
 	bool vlan_strip_disable;
 	bool scatter_fcs_en;
 	bool rx_dim_enabled;
 	bool tx_dim_enabled;
-	u32 lro_timeout;
 	u32 pflags;
 	struct bpf_prog *xdp_prog;
 	struct mlx5e_xsk *xsk;
@@ -717,6 +727,8 @@
 	DECLARE_BITMAP(state, MLX5E_CHANNEL_NUM_STATES);
 	int                        ix;
 	int                        cpu;
+	/* Sync between icosq recovery and XSK enable/disable. */
+	struct mutex               icosq_recovery_lock;
 };
 
 struct mlx5e_ptp;
@@ -944,9 +956,6 @@
 void mlx5e_destroy_rq(struct mlx5e_rq *rq);
 
 struct mlx5e_sq_param;
-int mlx5e_open_icosq(struct mlx5e_channel *c, struct mlx5e_params *params,
-		     struct mlx5e_sq_param *param, struct mlx5e_icosq *sq);
-void mlx5e_close_icosq(struct mlx5e_icosq *sq);
 int mlx5e_open_xdpsq(struct mlx5e_channel *c, struct mlx5e_params *params,
 		     struct mlx5e_sq_param *param, struct xsk_buff_pool *xsk_pool,
 		     struct mlx5e_xdpsq *sq, bool is_redirect);
@@ -993,7 +1002,7 @@
 void mlx5e_deactivate_priv_channels(struct mlx5e_priv *priv);
 int mlx5e_ptp_rx_manage_fs_ctx(struct mlx5e_priv *priv, void *ctx);
 
-int mlx5e_modify_rq_state(struct mlx5e_rq *rq, int curr_state, int next_state);
+int mlx5e_flush_rq(struct mlx5e_rq *rq, int curr_state);
 void mlx5e_activate_rq(struct mlx5e_rq *rq);
 void mlx5e_deactivate_rq(struct mlx5e_rq *rq);
 void mlx5e_activate_icosq(struct mlx5e_icosq *icosq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/fs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/fs.h
@@ -12,6 +12,7 @@
 enum {
 	MLX5E_TC_FT_LEVEL = 0,
 	MLX5E_TC_TTC_FT_LEVEL,
+	MLX5E_TC_MISS_LEVEL,
 };
 
 struct mlx5e_tc_table {
@@ -20,6 +21,7 @@
 	 */
 	struct mutex			t_lock;
 	struct mlx5_flow_table		*t;
+	struct mlx5_flow_table		*miss_t;
 	struct mlx5_fs_chains           *chains;
 	struct mlx5e_post_act		*post_act;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/fs_tt_redirect.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/fs_tt_redirect.c
@@ -156,6 +156,7 @@
 	in = kvzalloc(inlen, GFP_KERNEL);
 	if  (!in || !ft->g) {
 		kfree(ft->g);
+		ft->g = NULL;
 		kvfree(in);
 		return -ENOMEM;
 	}
@@ -434,6 +435,7 @@
 	in = kvzalloc(inlen, GFP_KERNEL);
 	if  (!in || !ft->g) {
 		kfree(ft->g);
+		ft->g = NULL;
 		kvfree(in);
 		return -ENOMEM;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/health.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/health.h
@@ -30,6 +30,8 @@
 void mlx5e_reporter_icosq_cqe_err(struct mlx5e_icosq *icosq);
 void mlx5e_reporter_rq_cqe_err(struct mlx5e_rq *rq);
 void mlx5e_reporter_rx_timeout(struct mlx5e_rq *rq);
+void mlx5e_reporter_icosq_suspend_recovery(struct mlx5e_channel *c);
+void mlx5e_reporter_icosq_resume_recovery(struct mlx5e_channel *c);
 
 #define MLX5E_REPORTER_PER_Q_MAX_LEN 256
 #define MLX5E_REPORTER_FLUSH_TIMEOUT_MSEC 2000
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/mod_hdr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/mod_hdr.c
@@ -155,3 +155,50 @@
 	return mh->modify_hdr;
 }
 
+char *
+mlx5e_mod_hdr_alloc(struct mlx5_core_dev *mdev, int namespace,
+		    struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts)
+{
+	int new_num_actions, max_hw_actions;
+	size_t new_sz, old_sz;
+	void *ret;
+
+	if (mod_hdr_acts->num_actions < mod_hdr_acts->max_actions)
+		goto out;
+
+	max_hw_actions = mlx5e_mod_hdr_max_actions(mdev, namespace);
+	new_num_actions = min(max_hw_actions,
+			      mod_hdr_acts->actions ?
+			      mod_hdr_acts->max_actions * 2 : 1);
+	if (mod_hdr_acts->max_actions == new_num_actions)
+		return ERR_PTR(-ENOSPC);
+
+	new_sz = MLX5_MH_ACT_SZ * new_num_actions;
+	old_sz = mod_hdr_acts->max_actions * MLX5_MH_ACT_SZ;
+
+	ret = krealloc(mod_hdr_acts->actions, new_sz, GFP_KERNEL);
+	if (!ret)
+		return ERR_PTR(-ENOMEM);
+
+	memset(ret + old_sz, 0, new_sz - old_sz);
+	mod_hdr_acts->actions = ret;
+	mod_hdr_acts->max_actions = new_num_actions;
+
+out:
+	return mod_hdr_acts->actions + (mod_hdr_acts->num_actions * MLX5_MH_ACT_SZ);
+}
+
+void
+mlx5e_mod_hdr_dealloc(struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts)
+{
+	kfree(mod_hdr_acts->actions);
+	mod_hdr_acts->actions = NULL;
+	mod_hdr_acts->num_actions = 0;
+	mod_hdr_acts->max_actions = 0;
+}
+
+char *
+mlx5e_mod_hdr_get_item(struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts, int pos)
+{
+	return mod_hdr_acts->actions + (pos * MLX5_MH_ACT_SZ);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/mod_hdr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/mod_hdr.h
@@ -15,6 +15,11 @@
 	void *actions;
 };
 
+char *mlx5e_mod_hdr_alloc(struct mlx5_core_dev *mdev, int namespace,
+			  struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts);
+void mlx5e_mod_hdr_dealloc(struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts);
+char *mlx5e_mod_hdr_get_item(struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts, int pos);
+
 struct mlx5e_mod_hdr_handle *
 mlx5e_mod_hdr_attach(struct mlx5_core_dev *mdev,
 		     struct mod_hdr_tbl *tbl,
@@ -28,4 +33,12 @@
 void mlx5e_mod_hdr_tbl_init(struct mod_hdr_tbl *tbl);
 void mlx5e_mod_hdr_tbl_destroy(struct mod_hdr_tbl *tbl);
 
+static inline int mlx5e_mod_hdr_max_actions(struct mlx5_core_dev *mdev, int namespace)
+{
+	if (namespace == MLX5_FLOW_NAMESPACE_FDB) /* FDB offloading */
+		return MLX5_CAP_ESW_FLOWTABLE_FDB(mdev, max_modify_header_actions);
+	else /* namespace is MLX5_FLOW_NAMESPACE_KERNEL - NIC offloading */
+		return MLX5_CAP_FLOWTABLE_NIC_RX(mdev, max_modify_header_actions);
+}
+
 #endif /* __MLX5E_EN_MOD_HDR_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/params.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/params.c
@@ -87,7 +87,8 @@
 	u32 linear_frag_sz = max(mlx5e_rx_get_linear_frag_sz(params, xsk),
 				 mlx5e_rx_get_linear_frag_sz(params, NULL));
 
-	return !params->lro_en && linear_frag_sz <= PAGE_SIZE;
+	return params->packet_merge.type == MLX5E_PACKET_MERGE_NONE &&
+		linear_frag_sz <= PAGE_SIZE;
 }
 
 bool mlx5e_verify_rx_mpwqe_strides(struct mlx5_core_dev *mdev,
@@ -164,19 +165,8 @@
 		mlx5e_rx_is_linear_skb(params, xsk) :
 		mlx5e_rx_mpwqe_is_linear_skb(mdev, params, xsk);
 
-	return is_linear_skb ? mlx5e_get_linear_rq_headroom(params, xsk) : 0;
-}
-
-struct mlx5e_lro_param mlx5e_get_lro_param(struct mlx5e_params *params)
-{
-	struct mlx5e_lro_param lro_param;
-
-	lro_param = (struct mlx5e_lro_param) {
-		.enabled = params->lro_en,
-		.timeout = params->lro_timeout,
-	};
-
-	return lro_param;
+	return is_linear_skb || params->packet_merge.type == MLX5E_PACKET_MERGE_SHAMPO ?
+		mlx5e_get_linear_rq_headroom(params, xsk) : 0;
 }
 
 u16 mlx5e_calc_sq_stop_room(struct mlx5_core_dev *mdev, struct mlx5e_params *params)
@@ -485,10 +475,11 @@
 
 static u8 rq_end_pad_mode(struct mlx5_core_dev *mdev, struct mlx5e_params *params)
 {
+	bool lro_en = params->packet_merge.type == MLX5E_PACKET_MERGE_LRO;
 	bool ro = pcie_relaxed_ordering_enabled(mdev->pdev) &&
 		MLX5_CAP_GEN(mdev, relaxed_ordering_write);
 
-	return ro && params->lro_en ?
+	return ro && lro_en ?
 		MLX5_WQ_END_PAD_MODE_NONE : MLX5_WQ_END_PAD_MODE_ALIGN;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/params.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/params.h
@@ -11,11 +11,6 @@
 	u16 chunk_size;
 };
 
-struct mlx5e_lro_param {
-	bool enabled;
-	u32 timeout;
-};
-
 struct mlx5e_cq_param {
 	u32                        cqc[MLX5_ST_SZ_DW(cqc)];
 	struct mlx5_wq_param       wq;
@@ -125,7 +120,6 @@
 u16 mlx5e_get_rq_headroom(struct mlx5_core_dev *mdev,
 			  struct mlx5e_params *params,
 			  struct mlx5e_xsk_param *xsk);
-struct mlx5e_lro_param mlx5e_get_lro_param(struct mlx5e_params *params);
 
 /* Build queue parameters */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c
@@ -309,8 +309,8 @@
 		if (err)
 			return err;
 
-		err = update_buffer_lossy(max_mtu, curr_pfc_en, prio2buffer, port_buff_cell_sz,
-					  xoff, &port_buffer, &update_buffer);
+		err = update_buffer_lossy(max_mtu, curr_pfc_en, prio2buffer, xoff,
+					  port_buff_cell_sz, &port_buffer, &update_buffer);
 		if (err)
 			return err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/ptp.c
@@ -126,6 +126,8 @@
 	/* ensure cq space is freed before enabling more cqes */
 	wmb();
 
+	mlx5e_txqsq_wake(&ptpsq->txqsq);
+
 	return work_done == budget;
 }
 
@@ -674,8 +676,10 @@
 
 	c = kvzalloc_node(sizeof(*c), GFP_KERNEL, dev_to_node(mlx5_core_dma_dev(mdev)));
 	cparams = kvzalloc(sizeof(*cparams), GFP_KERNEL);
-	if (!c || !cparams)
-		return -ENOMEM;
+	if (!c || !cparams) {
+		err = -ENOMEM;
+		goto err_free;
+	}
 
 	c->priv     = priv;
 	c->mdev     = priv->mdev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/ptp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/ptp.h
@@ -6,6 +6,7 @@
 
 #include "en.h"
 #include "en_stats.h"
+#include "en/txrx.h"
 #include <linux/ptp_classify.h>
 
 #define MLX5E_PTP_CHANNEL_IX 0
@@ -67,6 +68,14 @@
 		fk.ports.dst == htons(PTP_EV_PORT));
 }
 
+static inline bool mlx5e_ptpsq_fifo_has_room(struct mlx5e_txqsq *sq)
+{
+	if (!sq->ptpsq)
+		return true;
+
+	return mlx5e_skb_fifo_has_room(&sq->ptpsq->skb_fifo);
+}
+
 int mlx5e_ptp_open(struct mlx5e_priv *priv, struct mlx5e_params *params,
 		   u8 lag_port, struct mlx5e_ptp **cp);
 void mlx5e_ptp_close(struct mlx5e_ptp *c);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/qos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/qos.c
@@ -553,7 +553,8 @@
 
 static void mlx5e_htb_convert_ceil(struct mlx5e_priv *priv, u64 ceil, u32 *max_average_bw)
 {
-	*max_average_bw = div_u64(ceil, BYTES_IN_MBIT);
+	/* Hardware treats 0 as "unlimited", set at least 1. */
+	*max_average_bw = max_t(u32, div_u64(ceil, BYTES_IN_MBIT), 1);
 
 	qos_dbg(priv->mdev, "Convert: ceil %llu -> max_average_bw %u\n",
 		ceil, *max_average_bw);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rep/bond.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rep/bond.c
@@ -183,18 +183,7 @@
 
 static bool mlx5e_rep_is_lag_netdev(struct net_device *netdev)
 {
-	struct mlx5e_rep_priv *rpriv;
-	struct mlx5e_priv *priv;
-
-	/* A given netdev is not a representor or not a slave of LAG configuration */
-	if (!mlx5e_eswitch_rep(netdev) || !netif_is_lag_port(netdev))
-		return false;
-
-	priv = netdev_priv(netdev);
-	rpriv = priv->ppriv;
-
-	/* Egress acl forward to vport is supported only non-uplink representor */
-	return rpriv->rep->vport != MLX5_VPORT_UPLINK;
+	return netif_is_lag_port(netdev) && mlx5e_eswitch_vf_rep(netdev);
 }
 
 static void mlx5e_rep_changelowerstate_event(struct net_device *netdev, void *ptr)
@@ -210,9 +199,6 @@
 	u16 fwd_vport_num;
 	int err;
 
-	if (!mlx5e_rep_is_lag_netdev(netdev))
-		return;
-
 	info = ptr;
 	lag_info = info->lower_state_info;
 	/* This is not an event of a representor becoming active slave */
@@ -266,9 +252,6 @@
 	struct net_device *lag_dev;
 	struct mlx5e_priv *priv;
 
-	if (!mlx5e_rep_is_lag_netdev(netdev))
-		return;
-
 	priv = netdev_priv(netdev);
 	rpriv = priv->ppriv;
 	lag_dev = info->upper_dev;
@@ -293,6 +276,19 @@
 				       unsigned long event, void *ptr)
 {
 	struct net_device *netdev = netdev_notifier_info_to_dev(ptr);
+	struct mlx5e_rep_priv *rpriv;
+	struct mlx5e_rep_bond *bond;
+	struct mlx5e_priv *priv;
+
+	if (!mlx5e_rep_is_lag_netdev(netdev))
+		return NOTIFY_DONE;
+
+	bond = container_of(nb, struct mlx5e_rep_bond, nb);
+	priv = netdev_priv(netdev);
+	rpriv = mlx5_eswitch_get_uplink_priv(priv->mdev->priv.eswitch, REP_ETH);
+	/* Verify VF representor is on the same device of the bond handling the netevent. */
+	if (rpriv->uplink_priv.bond != bond)
+		return NOTIFY_DONE;
 
 	switch (event) {
 	case NETDEV_CHANGELOWERSTATE:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rep/bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rep/bridge.c
@@ -48,15 +48,10 @@
 	struct list_head *iter;
 
 	netdev_for_each_lower_dev(dev, lower, iter) {
-		struct mlx5_core_dev *mdev;
-		struct mlx5e_priv *priv;
-
 		if (!mlx5e_eswitch_rep(lower))
 			continue;
 
-		priv = netdev_priv(lower);
-		mdev = priv->mdev;
-		if (mlx5_lag_is_shared_fdb(mdev) && mlx5_esw_bridge_dev_same_esw(lower, esw))
+		if (mlx5_esw_bridge_dev_same_esw(lower, esw))
 			return lower;
 	}
 
@@ -121,7 +116,7 @@
 	priv = netdev_priv(rep);
 	mdev = priv->mdev;
 	if (netif_is_lag_master(dev))
-		return mlx5_lag_is_shared_fdb(mdev) && mlx5_lag_is_master(mdev);
+		return mlx5_lag_is_master(mdev);
 	return true;
 }
 
@@ -164,6 +159,36 @@
 	return err;
 }
 
+static int
+mlx5_esw_bridge_changeupper_validate_netdev(void *ptr)
+{
+	struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+	struct netdev_notifier_changeupper_info *info = ptr;
+	struct net_device *upper = info->upper_dev;
+	struct net_device *lower;
+	struct list_head *iter;
+
+	if (!netif_is_bridge_master(upper) || !netif_is_lag_master(dev))
+		return 0;
+
+	netdev_for_each_lower_dev(dev, lower, iter) {
+		struct mlx5_core_dev *mdev;
+		struct mlx5e_priv *priv;
+
+		if (!mlx5e_eswitch_rep(lower))
+			continue;
+
+		priv = netdev_priv(lower);
+		mdev = priv->mdev;
+		if (!mlx5_lag_is_active(mdev))
+			return -EAGAIN;
+		if (!mlx5_lag_is_shared_fdb(mdev))
+			return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
 static int mlx5_esw_bridge_switchdev_port_event(struct notifier_block *nb,
 						unsigned long event, void *ptr)
 {
@@ -171,6 +196,7 @@
 
 	switch (event) {
 	case NETDEV_PRECHANGEUPPER:
+		err = mlx5_esw_bridge_changeupper_validate_netdev(ptr);
 		break;
 
 	case NETDEV_CHANGEUPPER:
@@ -399,12 +425,11 @@
 	if (!rep)
 		return NOTIFY_DONE;
 
+	if (netif_is_lag_master(dev) && !mlx5_lag_is_shared_fdb(esw->dev))
+		return NOTIFY_DONE;
+
 	switch (event) {
 	case SWITCHDEV_FDB_ADD_TO_BRIDGE:
-		/* only handle the event on native eswtich of representor */
-		if (!mlx5_esw_bridge_is_local(dev, rep, esw))
-			break;
-
 		fdb_info = container_of(info,
 					struct switchdev_notifier_fdb_info,
 					info);
@@ -491,7 +516,7 @@
 	}
 
 	br_offloads->netdev_nb.notifier_call = mlx5_esw_bridge_switchdev_port_event;
-	err = register_netdevice_notifier(&br_offloads->netdev_nb);
+	err = register_netdevice_notifier_net(&init_net, &br_offloads->netdev_nb);
 	if (err) {
 		esw_warn(mdev, "Failed to register bridge offloads netdevice notifier (err=%d)\n",
 			 err);
@@ -509,7 +534,9 @@
 err_register_swdev:
 	destroy_workqueue(br_offloads->wq);
 err_alloc_wq:
+	rtnl_lock();
 	mlx5_esw_bridge_cleanup(esw);
+	rtnl_unlock();
 }
 
 void mlx5e_rep_bridge_cleanup(struct mlx5e_priv *priv)
@@ -524,7 +551,7 @@
 		return;
 
 	cancel_delayed_work_sync(&br_offloads->update_work);
-	unregister_netdevice_notifier(&br_offloads->netdev_nb);
+	unregister_netdevice_notifier_net(&init_net, &br_offloads->netdev_nb);
 	unregister_switchdev_blocking_notifier(&br_offloads->nb_blk);
 	unregister_switchdev_notifier(&br_offloads->nb);
 	destroy_workqueue(br_offloads->wq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rep/tc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rep/tc.c
@@ -3,6 +3,7 @@
 
 #include <net/dst_metadata.h>
 #include <linux/netdevice.h>
+#include <linux/if_macvlan.h>
 #include <linux/list.h>
 #include <linux/rculist.h>
 #include <linux/rtnetlink.h>
@@ -18,10 +19,13 @@
 #include "en/tc_tun.h"
 #include "lib/port_tun.h"
 #include "en/tc/sample.h"
+#include "en_accel/ipsec_rxtx.h"
+#include "en/tc/int_port.h"
 
 struct mlx5e_rep_indr_block_priv {
 	struct net_device *netdev;
 	struct mlx5e_rep_priv *rpriv;
+	enum flow_block_binder_type binder_type;
 
 	struct list_head list;
 };
@@ -296,14 +300,16 @@
 
 static struct mlx5e_rep_indr_block_priv *
 mlx5e_rep_indr_block_priv_lookup(struct mlx5e_rep_priv *rpriv,
-				 struct net_device *netdev)
+				 struct net_device *netdev,
+				 enum flow_block_binder_type binder_type)
 {
 	struct mlx5e_rep_indr_block_priv *cb_priv;
 
 	list_for_each_entry(cb_priv,
 			    &rpriv->uplink_priv.tc_indr_block_priv_list,
 			    list)
-		if (cb_priv->netdev == netdev)
+		if (cb_priv->netdev == netdev &&
+		    cb_priv->binder_type == binder_type)
 			return cb_priv;
 
 	return NULL;
@@ -341,9 +347,13 @@
 static int mlx5e_rep_indr_setup_tc_cb(enum tc_setup_type type,
 				      void *type_data, void *indr_priv)
 {
-	unsigned long flags = MLX5_TC_FLAG(EGRESS) | MLX5_TC_FLAG(ESW_OFFLOAD);
+	unsigned long flags = MLX5_TC_FLAG(ESW_OFFLOAD);
 	struct mlx5e_rep_indr_block_priv *priv = indr_priv;
 
+	flags |= (priv->binder_type == FLOW_BLOCK_BINDER_TYPE_CLSACT_EGRESS) ?
+		MLX5_TC_FLAG(EGRESS) :
+		MLX5_TC_FLAG(INGRESS);
+
 	switch (type) {
 	case TC_SETUP_CLSFLOWER:
 		return mlx5e_rep_indr_offload(priv->netdev, type_data, priv,
@@ -409,6 +419,13 @@
 
 static LIST_HEAD(mlx5e_block_cb_list);
 
+static bool mlx5e_rep_macvlan_mode_supported(const struct net_device *dev)
+{
+	struct macvlan_dev *macvlan = netdev_priv(dev);
+
+	return macvlan->mode == MACVLAN_MODE_PASSTHRU;
+}
+
 static int
 mlx5e_rep_indr_setup_block(struct net_device *netdev, struct Qdisc *sch,
 			   struct mlx5e_rep_priv *rpriv,
@@ -418,14 +435,30 @@
 			   void (*cleanup)(struct flow_block_cb *block_cb))
 {
 	struct mlx5e_priv *priv = netdev_priv(rpriv->netdev);
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	bool is_ovs_int_port = netif_is_ovs_master(netdev);
 	struct mlx5e_rep_indr_block_priv *indr_priv;
 	struct flow_block_cb *block_cb;
 
 	if (!mlx5e_tc_tun_device_to_offload(priv, netdev) &&
-	    !(is_vlan_dev(netdev) && vlan_dev_real_dev(netdev) == rpriv->netdev))
+	    !(is_vlan_dev(netdev) && vlan_dev_real_dev(netdev) == rpriv->netdev) &&
+	    !is_ovs_int_port) {
+		if (!(netif_is_macvlan(netdev) && macvlan_dev_real_dev(netdev) == rpriv->netdev))
+			return -EOPNOTSUPP;
+		if (!mlx5e_rep_macvlan_mode_supported(netdev)) {
+			netdev_warn(netdev, "Offloading ingress filter is supported only with macvlan passthru mode");
+			return -EOPNOTSUPP;
+		}
+	}
+
+	if (f->binder_type != FLOW_BLOCK_BINDER_TYPE_CLSACT_INGRESS &&
+	    f->binder_type != FLOW_BLOCK_BINDER_TYPE_CLSACT_EGRESS)
 		return -EOPNOTSUPP;
 
-	if (f->binder_type != FLOW_BLOCK_BINDER_TYPE_CLSACT_INGRESS)
+	if (f->binder_type == FLOW_BLOCK_BINDER_TYPE_CLSACT_EGRESS && !is_ovs_int_port)
+		return -EOPNOTSUPP;
+
+	if (is_ovs_int_port && !mlx5e_tc_int_port_supported(esw))
 		return -EOPNOTSUPP;
 
 	f->unlocked_driver_cb = true;
@@ -433,7 +466,7 @@
 
 	switch (f->command) {
 	case FLOW_BLOCK_BIND:
-		indr_priv = mlx5e_rep_indr_block_priv_lookup(rpriv, netdev);
+		indr_priv = mlx5e_rep_indr_block_priv_lookup(rpriv, netdev, f->binder_type);
 		if (indr_priv)
 			return -EEXIST;
 
@@ -443,6 +476,7 @@
 
 		indr_priv->netdev = netdev;
 		indr_priv->rpriv = rpriv;
+		indr_priv->binder_type = f->binder_type;
 		list_add(&indr_priv->list,
 			 &rpriv->uplink_priv.tc_indr_block_priv_list);
 
@@ -460,7 +494,7 @@
 
 		return 0;
 	case FLOW_BLOCK_UNBIND:
-		indr_priv = mlx5e_rep_indr_block_priv_lookup(rpriv, netdev);
+		indr_priv = mlx5e_rep_indr_block_priv_lookup(rpriv, netdev, f->binder_type);
 		if (!indr_priv)
 			return -ENOENT;
 
@@ -597,8 +631,8 @@
 		return false;
 	}
 
-	/* Set tun_dev so we do dev_put() after datapath */
-	tc_priv->tun_dev = dev;
+	/* Set fwd_dev so we do dev_put() after datapath */
+	tc_priv->fwd_dev = dev;
 
 	skb->dev = dev;
 
@@ -638,6 +672,12 @@
 	return mlx5e_restore_tunnel(priv, skb, tc_priv, tunnel_id);
 }
 
+static void mlx5_rep_tc_post_napi_receive(struct mlx5e_tc_update_priv *tc_priv)
+{
+	if (tc_priv->fwd_dev)
+		dev_put(tc_priv->fwd_dev);
+}
+
 static void mlx5e_restore_skb_sample(struct mlx5e_priv *priv, struct sk_buff *skb,
 				     struct mlx5_mapped_obj *mapped_obj,
 				     struct mlx5e_tc_update_priv *tc_priv)
@@ -647,25 +687,54 @@
 			   "Failed to restore tunnel info for sampled packet\n");
 		return;
 	}
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
 	mlx5e_tc_sample_skb(skb, mapped_obj);
-#endif /* CONFIG_MLX5_TC_SAMPLE */
 	mlx5_rep_tc_post_napi_receive(tc_priv);
 }
 
-bool mlx5e_rep_tc_update_skb(struct mlx5_cqe64 *cqe,
-			     struct sk_buff *skb,
-			     struct mlx5e_tc_update_priv *tc_priv)
+static bool mlx5e_restore_skb_int_port(struct mlx5e_priv *priv, struct sk_buff *skb,
+				       struct mlx5_mapped_obj *mapped_obj,
+				       struct mlx5e_tc_update_priv *tc_priv,
+				       bool *forward_tx,
+				       u32 reg_c1)
+{
+	u32 tunnel_id = (reg_c1 >> ESW_TUN_OFFSET) & TUNNEL_ID_MASK;
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	struct mlx5_rep_uplink_priv *uplink_priv;
+	struct mlx5e_rep_priv *uplink_rpriv;
+
+	/* Tunnel restore takes precedence over int port restore */
+	if (tunnel_id)
+		return mlx5e_restore_tunnel(priv, skb, tc_priv, tunnel_id);
+
+	uplink_rpriv = mlx5_eswitch_get_uplink_priv(esw, REP_ETH);
+	uplink_priv = &uplink_rpriv->uplink_priv;
+
+	if (mlx5e_tc_int_port_dev_fwd(uplink_priv->int_port_priv, skb,
+				      mapped_obj->int_port_metadata, forward_tx)) {
+		/* Set fwd_dev for future dev_put */
+		tc_priv->fwd_dev = skb->dev;
+
+		return true;
+	}
+
+	return false;
+}
+
+void mlx5e_rep_tc_receive(struct mlx5_cqe64 *cqe, struct mlx5e_rq *rq,
+			  struct sk_buff *skb)
 {
+	u32 reg_c1 = be32_to_cpu(cqe->ft_metadata);
+	struct mlx5e_tc_update_priv tc_priv = {};
 	struct mlx5_mapped_obj mapped_obj;
 	struct mlx5_eswitch *esw;
+	bool forward_tx = false;
 	struct mlx5e_priv *priv;
 	u32 reg_c0;
 	int err;
 
 	reg_c0 = (be32_to_cpu(cqe->sop_drop_qpn) & MLX5E_TC_FLOW_ID_MASK);
 	if (!reg_c0 || reg_c0 == MLX5_FS_DEFAULT_FLOW_TAG)
-		return true;
+		goto forward;
 
 	/* If reg_c0 is not equal to the default flow tag then skb->mark
 	 * is not supported and must be reset back to 0.
@@ -679,26 +748,35 @@
 		netdev_dbg(priv->netdev,
 			   "Couldn't find mapped object for reg_c0: %d, err: %d\n",
 			   reg_c0, err);
-		return false;
+		goto free_skb;
 	}
 
 	if (mapped_obj.type == MLX5_MAPPED_OBJ_CHAIN) {
-		u32 reg_c1 = be32_to_cpu(cqe->ft_metadata);
-
-		return mlx5e_restore_skb_chain(skb, mapped_obj.chain, reg_c1, tc_priv);
+		if (!mlx5e_restore_skb_chain(skb, mapped_obj.chain, reg_c1, &tc_priv) &&
+		    !mlx5_ipsec_is_rx_flow(cqe))
+			goto free_skb;
 	} else if (mapped_obj.type == MLX5_MAPPED_OBJ_SAMPLE) {
-		mlx5e_restore_skb_sample(priv, skb, &mapped_obj, tc_priv);
-		return false;
+		mlx5e_restore_skb_sample(priv, skb, &mapped_obj, &tc_priv);
+		goto free_skb;
+	} else if (mapped_obj.type == MLX5_MAPPED_OBJ_INT_PORT_METADATA) {
+		if (!mlx5e_restore_skb_int_port(priv, skb, &mapped_obj, &tc_priv,
+						&forward_tx, reg_c1))
+			goto free_skb;
 	} else {
 		netdev_dbg(priv->netdev, "Invalid mapped object type: %d\n", mapped_obj.type);
-		return false;
+		goto free_skb;
 	}
 
-	return true;
-}
+forward:
+	if (forward_tx)
+		dev_queue_xmit(skb);
+	else
+		napi_gro_receive(rq->cq.napi, skb);
 
-void mlx5_rep_tc_post_napi_receive(struct mlx5e_tc_update_priv *tc_priv)
-{
-	if (tc_priv->tun_dev)
-		dev_put(tc_priv->tun_dev);
+	mlx5_rep_tc_post_napi_receive(&tc_priv);
+
+	return;
+
+free_skb:
+	dev_kfree_skb_any(skb);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rep/tc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rep/tc.h
@@ -36,10 +36,8 @@
 int mlx5e_rep_setup_tc(struct net_device *dev, enum tc_setup_type type,
 		       void *type_data);
 
-bool mlx5e_rep_tc_update_skb(struct mlx5_cqe64 *cqe,
-			     struct sk_buff *skb,
-			     struct mlx5e_tc_update_priv *tc_priv);
-void mlx5_rep_tc_post_napi_receive(struct mlx5e_tc_update_priv *tc_priv);
+void mlx5e_rep_tc_receive(struct mlx5_cqe64 *cqe, struct mlx5e_rq *rq,
+			  struct sk_buff *skb);
 
 #else /* CONFIG_MLX5_CLS_ACT */
 
@@ -66,13 +64,9 @@
 mlx5e_rep_setup_tc(struct net_device *dev, enum tc_setup_type type,
 		   void *type_data) { return -EOPNOTSUPP; }
 
-struct mlx5e_tc_update_priv;
-static inline bool
-mlx5e_rep_tc_update_skb(struct mlx5_cqe64 *cqe,
-			struct sk_buff *skb,
-			struct mlx5e_tc_update_priv *tc_priv) { return true; }
 static inline void
-mlx5_rep_tc_post_napi_receive(struct mlx5e_tc_update_priv *tc_priv) {}
+mlx5e_rep_tc_receive(struct mlx5_cqe64 *cqe, struct mlx5e_rq *rq,
+		     struct sk_buff *skb) { napi_gro_receive(rq->cq.napi, skb); }
 
 #endif /* CONFIG_MLX5_CLS_ACT */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c
@@ -59,6 +59,7 @@
 
 static int mlx5e_rx_reporter_err_icosq_cqe_recover(void *ctx)
 {
+	struct mlx5e_rq *xskrq = NULL;
 	struct mlx5_core_dev *mdev;
 	struct mlx5e_icosq *icosq;
 	struct net_device *dev;
@@ -67,7 +68,13 @@
 	int err;
 
 	icosq = ctx;
+
+	mutex_lock(&icosq->channel->icosq_recovery_lock);
+
+	/* mlx5e_close_rq cancels this work before RQ and ICOSQ are killed. */
 	rq = &icosq->channel->rq;
+	if (test_bit(MLX5E_RQ_STATE_ENABLED, &icosq->channel->xskrq.state))
+		xskrq = &icosq->channel->xskrq;
 	mdev = icosq->channel->mdev;
 	dev = icosq->channel->netdev;
 	err = mlx5_core_query_sq_state(mdev, icosq->sqn, &state);
@@ -81,6 +88,9 @@
 		goto out;
 
 	mlx5e_deactivate_rq(rq);
+	if (xskrq)
+		mlx5e_deactivate_rq(xskrq);
+
 	err = mlx5e_wait_for_icosq_flush(icosq);
 	if (err)
 		goto out;
@@ -94,35 +104,29 @@
 		goto out;
 
 	mlx5e_reset_icosq_cc_pc(icosq);
+
 	mlx5e_free_rx_in_progress_descs(rq);
+	if (xskrq)
+		mlx5e_free_rx_in_progress_descs(xskrq);
+
 	clear_bit(MLX5E_SQ_STATE_RECOVERING, &icosq->state);
 	mlx5e_activate_icosq(icosq);
-	mlx5e_activate_rq(rq);
 
+	mlx5e_activate_rq(rq);
 	rq->stats->recover++;
-	return 0;
-out:
-	clear_bit(MLX5E_SQ_STATE_RECOVERING, &icosq->state);
-	return err;
-}
-
-static int mlx5e_rq_to_ready(struct mlx5e_rq *rq, int curr_state)
-{
-	struct net_device *dev = rq->netdev;
-	int err;
 
-	err = mlx5e_modify_rq_state(rq, curr_state, MLX5_RQC_STATE_RST);
-	if (err) {
-		netdev_err(dev, "Failed to move rq 0x%x to reset\n", rq->rqn);
-		return err;
-	}
-	err = mlx5e_modify_rq_state(rq, MLX5_RQC_STATE_RST, MLX5_RQC_STATE_RDY);
-	if (err) {
-		netdev_err(dev, "Failed to move rq 0x%x to ready\n", rq->rqn);
-		return err;
+	if (xskrq) {
+		mlx5e_activate_rq(xskrq);
+		xskrq->stats->recover++;
 	}
 
+	mutex_unlock(&icosq->channel->icosq_recovery_lock);
+
 	return 0;
+out:
+	clear_bit(MLX5E_SQ_STATE_RECOVERING, &icosq->state);
+	mutex_unlock(&icosq->channel->icosq_recovery_lock);
+	return err;
 }
 
 static int mlx5e_rx_reporter_err_rq_cqe_recover(void *ctx)
@@ -131,19 +135,14 @@
 	int err;
 
 	mlx5e_deactivate_rq(rq);
-	mlx5e_free_rx_descs(rq);
-
-	err = mlx5e_rq_to_ready(rq, MLX5_RQC_STATE_ERR);
+	err = mlx5e_flush_rq(rq, MLX5_RQC_STATE_ERR);
+	clear_bit(MLX5E_RQ_STATE_RECOVERING, &rq->state);
 	if (err)
-		goto out;
+		return err;
 
-	clear_bit(MLX5E_RQ_STATE_RECOVERING, &rq->state);
 	mlx5e_activate_rq(rq);
 	rq->stats->recover++;
 	return 0;
-out:
-	clear_bit(MLX5E_RQ_STATE_RECOVERING, &rq->state);
-	return err;
 }
 
 static int mlx5e_rx_reporter_timeout_recover(void *ctx)
@@ -656,11 +655,11 @@
 
 void mlx5e_reporter_rx_timeout(struct mlx5e_rq *rq)
 {
-	char icosq_str[MLX5E_REPORTER_PER_Q_MAX_LEN] = {};
 	char err_str[MLX5E_REPORTER_PER_Q_MAX_LEN];
 	struct mlx5e_icosq *icosq = rq->icosq;
 	struct mlx5e_priv *priv = rq->priv;
 	struct mlx5e_err_ctx err_ctx = {};
+	char icosq_str[32] = {};
 
 	err_ctx.ctx = rq;
 	err_ctx.recover = mlx5e_rx_reporter_timeout_recover;
@@ -669,7 +668,7 @@
 	if (icosq)
 		snprintf(icosq_str, sizeof(icosq_str), "ICOSQ: 0x%x, ", icosq->sqn);
 	snprintf(err_str, sizeof(err_str),
-		 "RX timeout on channel: %d, %sRQ: 0x%x, CQ: 0x%x",
+		 "RX timeout on channel: %d, %s RQ: 0x%x, CQ: 0x%x",
 		 rq->ix, icosq_str, rq->rqn, rq->cq.mcq.cqn);
 
 	mlx5e_health_report(priv, priv->rx_reporter, err_str, &err_ctx);
@@ -703,6 +702,16 @@
 	mlx5e_health_report(priv, priv->rx_reporter, err_str, &err_ctx);
 }
 
+void mlx5e_reporter_icosq_suspend_recovery(struct mlx5e_channel *c)
+{
+	mutex_lock(&c->icosq_recovery_lock);
+}
+
+void mlx5e_reporter_icosq_resume_recovery(struct mlx5e_channel *c)
+{
+	mutex_unlock(&c->icosq_recovery_lock);
+}
+
 static const struct devlink_health_reporter_ops mlx5_rx_reporter_ops = {
 	.name = "rx",
 	.recover = mlx5e_rx_reporter_recover,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/reporter_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/reporter_tx.c
@@ -463,6 +463,14 @@
 	return mlx5e_health_fmsg_named_obj_nest_end(fmsg);
 }
 
+static int mlx5e_tx_reporter_timeout_dump(struct mlx5e_priv *priv, struct devlink_fmsg *fmsg,
+					  void *ctx)
+{
+	struct mlx5e_tx_timeout_ctx *to_ctx = ctx;
+
+	return mlx5e_tx_reporter_dump_sq(priv, fmsg, to_ctx->sq);
+}
+
 static int mlx5e_tx_reporter_dump_all_sqs(struct mlx5e_priv *priv,
 					  struct devlink_fmsg *fmsg)
 {
@@ -558,7 +566,7 @@
 	to_ctx.sq = sq;
 	err_ctx.ctx = &to_ctx;
 	err_ctx.recover = mlx5e_tx_reporter_timeout_recover;
-	err_ctx.dump = mlx5e_tx_reporter_dump_sq;
+	err_ctx.dump = mlx5e_tx_reporter_timeout_dump;
 	snprintf(err_str, sizeof(err_str),
 		 "TX timeout on queue: %d, SQ: 0x%x, CQ: 0x%x, SQ Cons: 0x%x SQ Prod: 0x%x, usecs since last trans: %u",
 		 sq->ch_ix, sq->sqn, sq->cq.mcq.cqn, sq->cc, sq->pc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rss.c
@@ -127,7 +127,7 @@
 
 static int mlx5e_rss_create_tir(struct mlx5e_rss *rss,
 				enum mlx5_traffic_types tt,
-				const struct mlx5e_lro_param *init_lro_param,
+				const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 				bool inner)
 {
 	struct mlx5e_rss_params_traffic_type rss_tt;
@@ -161,7 +161,7 @@
 	rqtn = mlx5e_rqt_get_rqtn(&rss->rqt);
 	mlx5e_tir_builder_build_rqt(builder, rss->mdev->mlx5e_res.hw_objs.td.tdn,
 				    rqtn, rss->inner_ft_support);
-	mlx5e_tir_builder_build_lro(builder, init_lro_param);
+	mlx5e_tir_builder_build_packet_merge(builder, init_pkt_merge_param);
 	rss_tt = mlx5e_rss_get_tt_config(rss, tt);
 	mlx5e_tir_builder_build_rss(builder, &rss->hash, &rss_tt, inner);
 
@@ -198,14 +198,14 @@
 }
 
 static int mlx5e_rss_create_tirs(struct mlx5e_rss *rss,
-				 const struct mlx5e_lro_param *init_lro_param,
+				 const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 				 bool inner)
 {
 	enum mlx5_traffic_types tt, max_tt;
 	int err;
 
 	for (tt = 0; tt < MLX5E_NUM_INDIR_TIRS; tt++) {
-		err = mlx5e_rss_create_tir(rss, tt, init_lro_param, inner);
+		err = mlx5e_rss_create_tir(rss, tt, init_pkt_merge_param, inner);
 		if (err)
 			goto err_destroy_tirs;
 	}
@@ -297,7 +297,7 @@
 
 int mlx5e_rss_init(struct mlx5e_rss *rss, struct mlx5_core_dev *mdev,
 		   bool inner_ft_support, u32 drop_rqn,
-		   const struct mlx5e_lro_param *init_lro_param)
+		   const struct mlx5e_packet_merge_param *init_pkt_merge_param)
 {
 	int err;
 
@@ -305,12 +305,12 @@
 	if (err)
 		goto err_out;
 
-	err = mlx5e_rss_create_tirs(rss, init_lro_param, false);
+	err = mlx5e_rss_create_tirs(rss, init_pkt_merge_param, false);
 	if (err)
 		goto err_destroy_rqt;
 
 	if (inner_ft_support) {
-		err = mlx5e_rss_create_tirs(rss, init_lro_param, true);
+		err = mlx5e_rss_create_tirs(rss, init_pkt_merge_param, true);
 		if (err)
 			goto err_destroy_tirs;
 	}
@@ -372,7 +372,7 @@
  */
 int mlx5e_rss_obtain_tirn(struct mlx5e_rss *rss,
 			  enum mlx5_traffic_types tt,
-			  const struct mlx5e_lro_param *init_lro_param,
+			  const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 			  bool inner, u32 *tirn)
 {
 	struct mlx5e_tir *tir;
@@ -381,7 +381,7 @@
 	if (!tir) { /* TIR doesn't exist, create one */
 		int err;
 
-		err = mlx5e_rss_create_tir(rss, tt, init_lro_param, inner);
+		err = mlx5e_rss_create_tir(rss, tt, init_pkt_merge_param, inner);
 		if (err)
 			return err;
 		tir = rss_get_tir(rss, tt, inner);
@@ -418,7 +418,8 @@
 			       mlx5e_rqt_get_rqtn(&rss->rqt), rss->drop_rqn, err);
 }
 
-int mlx5e_rss_lro_set_param(struct mlx5e_rss *rss, struct mlx5e_lro_param *lro_param)
+int mlx5e_rss_packet_merge_set_param(struct mlx5e_rss *rss,
+				     struct mlx5e_packet_merge_param *pkt_merge_param)
 {
 	struct mlx5e_tir_builder *builder;
 	enum mlx5_traffic_types tt;
@@ -428,7 +429,7 @@
 	if (!builder)
 		return -ENOMEM;
 
-	mlx5e_tir_builder_build_lro(builder, lro_param);
+	mlx5e_tir_builder_build_packet_merge(builder, pkt_merge_param);
 
 	final_err = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rss.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rss.h
@@ -17,7 +17,7 @@
 void mlx5e_rss_free(struct mlx5e_rss *rss);
 int mlx5e_rss_init(struct mlx5e_rss *rss, struct mlx5_core_dev *mdev,
 		   bool inner_ft_support, u32 drop_rqn,
-		   const struct mlx5e_lro_param *init_lro_param);
+		   const struct mlx5e_packet_merge_param *init_pkt_merge_param);
 int mlx5e_rss_init_no_tirs(struct mlx5e_rss *rss, struct mlx5_core_dev *mdev,
 			   bool inner_ft_support, u32 drop_rqn);
 int mlx5e_rss_cleanup(struct mlx5e_rss *rss);
@@ -30,13 +30,14 @@
 		       bool inner);
 int mlx5e_rss_obtain_tirn(struct mlx5e_rss *rss,
 			  enum mlx5_traffic_types tt,
-			  const struct mlx5e_lro_param *init_lro_param,
+			  const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 			  bool inner, u32 *tirn);
 
 void mlx5e_rss_enable(struct mlx5e_rss *rss, u32 *rqns, unsigned int num_rqns);
 void mlx5e_rss_disable(struct mlx5e_rss *rss);
 
-int mlx5e_rss_lro_set_param(struct mlx5e_rss *rss, struct mlx5e_lro_param *lro_param);
+int mlx5e_rss_packet_merge_set_param(struct mlx5e_rss *rss,
+				     struct mlx5e_packet_merge_param *pkt_merge_param);
 int mlx5e_rss_get_rxfh(struct mlx5e_rss *rss, u32 *indir, u8 *key, u8 *hfunc);
 int mlx5e_rss_set_rxfh(struct mlx5e_rss *rss, const u32 *indir,
 		       const u8 *key, const u8 *hfunc,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rx_res.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rx_res.c
@@ -13,6 +13,9 @@
 	unsigned int max_nch;
 	u32 drop_rqn;
 
+	struct mlx5e_packet_merge_param pkt_merge_param;
+	struct rw_semaphore pkt_merge_param_sem;
+
 	struct mlx5e_rss *rss[MLX5E_MAX_NUM_RSS];
 	bool rss_active;
 	u32 rss_rqns[MLX5E_INDIR_RQT_SIZE];
@@ -34,7 +37,7 @@
 /* API for rx_res_rss_* */
 
 static int mlx5e_rx_res_rss_init_def(struct mlx5e_rx_res *res,
-				     const struct mlx5e_lro_param *init_lro_param,
+				     const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 				     unsigned int init_nch)
 {
 	bool inner_ft_support = res->features & MLX5E_RX_RES_FEATURE_INNER_FT;
@@ -49,7 +52,7 @@
 		return -ENOMEM;
 
 	err = mlx5e_rss_init(rss, res->mdev, inner_ft_support, res->drop_rqn,
-			     init_lro_param);
+			     init_pkt_merge_param);
 	if (err)
 		goto err_rss_free;
 
@@ -275,7 +278,7 @@
 }
 
 static int mlx5e_rx_res_channels_init(struct mlx5e_rx_res *res,
-				      const struct mlx5e_lro_param *init_lro_param)
+				      const struct mlx5e_packet_merge_param *init_pkt_merge_param)
 {
 	bool inner_ft_support = res->features & MLX5E_RX_RES_FEATURE_INNER_FT;
 	struct mlx5e_tir_builder *builder;
@@ -306,7 +309,7 @@
 		mlx5e_tir_builder_build_rqt(builder, res->mdev->mlx5e_res.hw_objs.td.tdn,
 					    mlx5e_rqt_get_rqtn(&res->channels[ix].direct_rqt),
 					    inner_ft_support);
-		mlx5e_tir_builder_build_lro(builder, init_lro_param);
+		mlx5e_tir_builder_build_packet_merge(builder, init_pkt_merge_param);
 		mlx5e_tir_builder_build_direct(builder);
 
 		err = mlx5e_tir_init(&res->channels[ix].direct_tir, builder, res->mdev, true);
@@ -336,7 +339,7 @@
 		mlx5e_tir_builder_build_rqt(builder, res->mdev->mlx5e_res.hw_objs.td.tdn,
 					    mlx5e_rqt_get_rqtn(&res->channels[ix].xsk_rqt),
 					    inner_ft_support);
-		mlx5e_tir_builder_build_lro(builder, init_lro_param);
+		mlx5e_tir_builder_build_packet_merge(builder, init_pkt_merge_param);
 		mlx5e_tir_builder_build_direct(builder);
 
 		err = mlx5e_tir_init(&res->channels[ix].xsk_tir, builder, res->mdev, true);
@@ -392,6 +395,7 @@
 	if (err)
 		goto out;
 
+	/* Separated from the channels RQs, does not share pkt_merge state with them */
 	mlx5e_tir_builder_build_rqt(builder, res->mdev->mlx5e_res.hw_objs.td.tdn,
 				    mlx5e_rqt_get_rqtn(&res->ptp.rqt),
 				    inner_ft_support);
@@ -437,7 +441,7 @@
 
 int mlx5e_rx_res_init(struct mlx5e_rx_res *res, struct mlx5_core_dev *mdev,
 		      enum mlx5e_rx_res_features features, unsigned int max_nch,
-		      u32 drop_rqn, const struct mlx5e_lro_param *init_lro_param,
+		      u32 drop_rqn, const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 		      unsigned int init_nch)
 {
 	int err;
@@ -447,11 +451,14 @@
 	res->max_nch = max_nch;
 	res->drop_rqn = drop_rqn;
 
-	err = mlx5e_rx_res_rss_init_def(res, init_lro_param, init_nch);
+	res->pkt_merge_param = *init_pkt_merge_param;
+	init_rwsem(&res->pkt_merge_param_sem);
+
+	err = mlx5e_rx_res_rss_init_def(res, init_pkt_merge_param, init_nch);
 	if (err)
 		goto err_out;
 
-	err = mlx5e_rx_res_channels_init(res, init_lro_param);
+	err = mlx5e_rx_res_channels_init(res, init_pkt_merge_param);
 	if (err)
 		goto err_rss_destroy;
 
@@ -513,7 +520,7 @@
 	return mlx5e_tir_get_tirn(&res->ptp.tir);
 }
 
-u32 mlx5e_rx_res_get_rqtn_direct(struct mlx5e_rx_res *res, unsigned int ix)
+static u32 mlx5e_rx_res_get_rqtn_direct(struct mlx5e_rx_res *res, unsigned int ix)
 {
 	return mlx5e_rqt_get_rqtn(&res->channels[ix].direct_rqt);
 }
@@ -645,7 +652,8 @@
 	return err;
 }
 
-int mlx5e_rx_res_lro_set_param(struct mlx5e_rx_res *res, struct mlx5e_lro_param *lro_param)
+int mlx5e_rx_res_packet_merge_set_param(struct mlx5e_rx_res *res,
+					struct mlx5e_packet_merge_param *pkt_merge_param)
 {
 	struct mlx5e_tir_builder *builder;
 	int err, final_err;
@@ -655,7 +663,10 @@
 	if (!builder)
 		return -ENOMEM;
 
-	mlx5e_tir_builder_build_lro(builder, lro_param);
+	down_write(&res->pkt_merge_param_sem);
+	res->pkt_merge_param = *pkt_merge_param;
+
+	mlx5e_tir_builder_build_packet_merge(builder, pkt_merge_param);
 
 	final_err = 0;
 
@@ -665,7 +676,7 @@
 		if (!rss)
 			continue;
 
-		err = mlx5e_rss_lro_set_param(rss, lro_param);
+		err = mlx5e_rss_packet_merge_set_param(rss, pkt_merge_param);
 		if (err)
 			final_err = final_err ? : err;
 	}
@@ -673,13 +684,14 @@
 	for (ix = 0; ix < res->max_nch; ix++) {
 		err = mlx5e_tir_modify(&res->channels[ix].direct_tir, builder);
 		if (err) {
-			mlx5_core_warn(res->mdev, "Failed to update LRO state of direct TIR %#x for channel %u: err = %d\n",
+			mlx5_core_warn(res->mdev, "Failed to update packet merge state of direct TIR %#x for channel %u: err = %d\n",
 				       mlx5e_tir_get_tirn(&res->channels[ix].direct_tir), ix, err);
 			if (!final_err)
 				final_err = err;
 		}
 	}
 
+	up_write(&res->pkt_merge_param_sem);
 	mlx5e_tir_builder_free(builder);
 	return final_err;
 }
@@ -688,3 +700,31 @@
 {
 	return mlx5e_rss_get_hash(res->rss[0]);
 }
+
+int mlx5e_rx_res_tls_tir_create(struct mlx5e_rx_res *res, unsigned int rxq,
+				struct mlx5e_tir *tir)
+{
+	bool inner_ft_support = res->features & MLX5E_RX_RES_FEATURE_INNER_FT;
+	struct mlx5e_tir_builder *builder;
+	u32 rqtn;
+	int err;
+
+	builder = mlx5e_tir_builder_alloc(false);
+	if (!builder)
+		return -ENOMEM;
+
+	rqtn = mlx5e_rx_res_get_rqtn_direct(res, rxq);
+
+	mlx5e_tir_builder_build_rqt(builder, res->mdev->mlx5e_res.hw_objs.td.tdn, rqtn,
+				    inner_ft_support);
+	mlx5e_tir_builder_build_direct(builder);
+	mlx5e_tir_builder_build_tls(builder);
+	down_read(&res->pkt_merge_param_sem);
+	mlx5e_tir_builder_build_packet_merge(builder, &res->pkt_merge_param);
+	err = mlx5e_tir_init(tir, builder, res->mdev, false);
+	up_read(&res->pkt_merge_param_sem);
+
+	mlx5e_tir_builder_free(builder);
+
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/rx_res.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/rx_res.h
@@ -25,7 +25,7 @@
 struct mlx5e_rx_res *mlx5e_rx_res_alloc(void);
 int mlx5e_rx_res_init(struct mlx5e_rx_res *res, struct mlx5_core_dev *mdev,
 		      enum mlx5e_rx_res_features features, unsigned int max_nch,
-		      u32 drop_rqn, const struct mlx5e_lro_param *init_lro_param,
+		      u32 drop_rqn, const struct mlx5e_packet_merge_param *init_pkt_merge_param,
 		      unsigned int init_nch);
 void mlx5e_rx_res_destroy(struct mlx5e_rx_res *res);
 void mlx5e_rx_res_free(struct mlx5e_rx_res *res);
@@ -37,9 +37,6 @@
 u32 mlx5e_rx_res_get_tirn_rss_inner(struct mlx5e_rx_res *res, enum mlx5_traffic_types tt);
 u32 mlx5e_rx_res_get_tirn_ptp(struct mlx5e_rx_res *res);
 
-/* RQTN getters for modules that create their own TIRs */
-u32 mlx5e_rx_res_get_rqtn_direct(struct mlx5e_rx_res *res, unsigned int ix);
-
 /* Activate/deactivate API */
 void mlx5e_rx_res_channels_activate(struct mlx5e_rx_res *res, struct mlx5e_channels *chs);
 void mlx5e_rx_res_channels_deactivate(struct mlx5e_rx_res *res);
@@ -57,7 +54,8 @@
 u8 mlx5e_rx_res_rss_get_hash_fields(struct mlx5e_rx_res *res, enum mlx5_traffic_types tt);
 int mlx5e_rx_res_rss_set_hash_fields(struct mlx5e_rx_res *res, enum mlx5_traffic_types tt,
 				     u8 rx_hash_fields);
-int mlx5e_rx_res_lro_set_param(struct mlx5e_rx_res *res, struct mlx5e_lro_param *lro_param);
+int mlx5e_rx_res_packet_merge_set_param(struct mlx5e_rx_res *res,
+					struct mlx5e_packet_merge_param *pkt_merge_param);
 
 int mlx5e_rx_res_rss_init(struct mlx5e_rx_res *res, u32 *rss_idx, unsigned int init_nch);
 int mlx5e_rx_res_rss_destroy(struct mlx5e_rx_res *res, u32 rss_idx);
@@ -68,4 +66,7 @@
 /* Workaround for hairpin */
 struct mlx5e_rss_params_hash mlx5e_rx_res_get_current_hash(struct mlx5e_rx_res *res);
 
+/* Accel TIRs */
+int mlx5e_rx_res_tls_tir_create(struct mlx5e_rx_res *res, unsigned int rxq,
+				struct mlx5e_tir *tir);
 #endif /* __MLX5_EN_RX_RES_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc/int_port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc/int_port.c
@@ -0,0 +1,457 @@
+// SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB
+/* Copyright (c) 2021, NVIDIA CORPORATION & AFFILIATES. All rights reserved. */
+
+#include <linux/mlx5/fs.h>
+#include "en/mapping.h"
+#include "en/tc/int_port.h"
+#include "en.h"
+#include "en_rep.h"
+#include "en_tc.h"
+
+struct mlx5e_tc_int_port {
+	enum mlx5e_tc_int_port_type type;
+	int ifindex;
+	u32 match_metadata;
+	u32 mapping;
+	struct list_head list;
+	struct mlx5_flow_handle *rx_rule;
+	refcount_t refcnt;
+	struct rcu_head rcu_head;
+};
+
+struct mlx5e_tc_int_port_priv {
+	struct mlx5_core_dev *dev;
+	struct mutex int_ports_lock; /* Protects int ports list */
+	struct list_head int_ports; /* Uses int_ports_lock */
+	u16 num_ports;
+	bool ul_rep_rx_ready; /* Set when uplink is performing teardown */
+	struct mapping_ctx *metadata_mapping; /* Metadata for source port rewrite and matching */
+};
+
+bool mlx5e_tc_int_port_supported(const struct mlx5_eswitch *esw)
+{
+	return mlx5_eswitch_vport_match_metadata_enabled(esw) &&
+	       MLX5_CAP_GEN(esw->dev, reg_c_preserve);
+}
+
+u32 mlx5e_tc_int_port_get_metadata(struct mlx5e_tc_int_port *int_port)
+{
+	return int_port->match_metadata;
+}
+
+int mlx5e_tc_int_port_get_flow_source(struct mlx5e_tc_int_port *int_port)
+{
+	/* For egress forwarding we can have the case
+	 * where the packet came from a vport and redirected
+	 * to int port or it came from the uplink, going
+	 * via internal port and hairpinned back to uplink
+	 * so we set the source to any port in this case.
+	 */
+	return int_port->type == MLX5E_TC_INT_PORT_EGRESS ?
+		MLX5_FLOW_CONTEXT_FLOW_SOURCE_ANY_VPORT :
+		MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK;
+}
+
+u32 mlx5e_tc_int_port_get_metadata_for_match(struct mlx5e_tc_int_port *int_port)
+{
+	return int_port->match_metadata << (32 - ESW_SOURCE_PORT_METADATA_BITS);
+}
+
+static struct mlx5_flow_handle *
+mlx5e_int_port_create_rx_rule(struct mlx5_eswitch *esw,
+			      struct mlx5e_tc_int_port *int_port,
+			      struct mlx5_flow_destination *dest)
+
+{
+	struct mlx5_flow_context *flow_context;
+	struct mlx5_flow_act flow_act = {};
+	struct mlx5_flow_handle *flow_rule;
+	struct mlx5_flow_spec *spec;
+	void *misc;
+
+	spec = kvzalloc(sizeof(*spec), GFP_KERNEL);
+	if (!spec)
+		return ERR_PTR(-ENOMEM);
+
+	misc = MLX5_ADDR_OF(fte_match_param, spec->match_value, misc_parameters_2);
+	MLX5_SET(fte_match_set_misc2, misc, metadata_reg_c_0,
+		 mlx5e_tc_int_port_get_metadata_for_match(int_port));
+
+	misc = MLX5_ADDR_OF(fte_match_param, spec->match_criteria, misc_parameters_2);
+	MLX5_SET(fte_match_set_misc2, misc, metadata_reg_c_0,
+		 mlx5_eswitch_get_vport_metadata_mask());
+
+	spec->match_criteria_enable = MLX5_MATCH_MISC_PARAMETERS_2;
+
+	/* Overwrite flow tag with the int port metadata mapping
+	 * instead of the chain mapping.
+	 */
+	flow_context = &spec->flow_context;
+	flow_context->flags |= FLOW_CONTEXT_HAS_TAG;
+	flow_context->flow_tag = int_port->mapping;
+	flow_act.action = MLX5_FLOW_CONTEXT_ACTION_FWD_DEST;
+	flow_rule = mlx5_add_flow_rules(esw->offloads.ft_offloads, spec,
+					&flow_act, dest, 1);
+	if (IS_ERR(flow_rule))
+		mlx5_core_warn(esw->dev, "ft offloads: Failed to add internal vport rx rule err %ld\n",
+			       PTR_ERR(flow_rule));
+
+	kvfree(spec);
+
+	return flow_rule;
+}
+
+static struct mlx5e_tc_int_port *
+mlx5e_int_port_lookup(struct mlx5e_tc_int_port_priv *priv,
+		      int ifindex,
+		      enum mlx5e_tc_int_port_type type)
+{
+	struct mlx5e_tc_int_port *int_port;
+
+	if (!priv->ul_rep_rx_ready)
+		goto not_found;
+
+	list_for_each_entry(int_port, &priv->int_ports, list)
+		if (int_port->ifindex == ifindex && int_port->type == type) {
+			refcount_inc(&int_port->refcnt);
+			return int_port;
+		}
+
+not_found:
+	return NULL;
+}
+
+static int mlx5e_int_port_metadata_alloc(struct mlx5e_tc_int_port_priv *priv,
+					 int ifindex, enum mlx5e_tc_int_port_type type,
+					 u32 *id)
+{
+	u32 mapped_key[2] = {type, ifindex};
+	int err;
+
+	err = mapping_add(priv->metadata_mapping, mapped_key, id);
+	if (err)
+		return err;
+
+	/* Fill upper 4 bits of PFNUM with reserved value */
+	*id |= 0xf << ESW_VPORT_BITS;
+
+	return 0;
+}
+
+static void mlx5e_int_port_metadata_free(struct mlx5e_tc_int_port_priv *priv,
+					 u32 id)
+{
+	id &= (1 << ESW_VPORT_BITS) - 1;
+	mapping_remove(priv->metadata_mapping, id);
+}
+
+/* Must be called with priv->int_ports_lock held */
+static struct mlx5e_tc_int_port *
+mlx5e_int_port_add(struct mlx5e_tc_int_port_priv *priv,
+		   int ifindex,
+		   enum mlx5e_tc_int_port_type type)
+{
+	struct mlx5_eswitch *esw = priv->dev->priv.eswitch;
+	struct mlx5_mapped_obj mapped_obj = {};
+	struct mlx5e_rep_priv *uplink_rpriv;
+	struct mlx5e_tc_int_port *int_port;
+	struct mlx5_flow_destination dest;
+	struct mapping_ctx *ctx;
+	u32 match_metadata;
+	u32 mapping;
+	int err;
+
+	if (priv->num_ports == MLX5E_TC_MAX_INT_PORT_NUM) {
+		mlx5_core_dbg(priv->dev, "Cannot add a new int port, max supported %d",
+			      MLX5E_TC_MAX_INT_PORT_NUM);
+		return ERR_PTR(-ENOSPC);
+	}
+
+	int_port = kzalloc(sizeof(*int_port), GFP_KERNEL);
+	if (!int_port)
+		return ERR_PTR(-ENOMEM);
+
+	err = mlx5e_int_port_metadata_alloc(priv, ifindex, type, &match_metadata);
+	if (err) {
+		mlx5_core_warn(esw->dev, "Cannot add a new internal port, metadata allocation failed for ifindex %d",
+			       ifindex);
+		goto err_metadata;
+	}
+
+	/* map metadata to reg_c0 object for miss handling */
+	ctx = esw->offloads.reg_c0_obj_pool;
+	mapped_obj.type = MLX5_MAPPED_OBJ_INT_PORT_METADATA;
+	mapped_obj.int_port_metadata = match_metadata;
+	err = mapping_add(ctx, &mapped_obj, &mapping);
+	if (err)
+		goto err_map;
+
+	int_port->type = type;
+	int_port->ifindex = ifindex;
+	int_port->match_metadata = match_metadata;
+	int_port->mapping = mapping;
+
+	/* Create a match on internal vport metadata in vport table */
+	uplink_rpriv = mlx5_eswitch_get_uplink_priv(esw, REP_ETH);
+
+	dest.type = MLX5_FLOW_DESTINATION_TYPE_FLOW_TABLE;
+	dest.ft = uplink_rpriv->root_ft;
+
+	int_port->rx_rule = mlx5e_int_port_create_rx_rule(esw, int_port, &dest);
+	if (IS_ERR(int_port->rx_rule)) {
+		err = PTR_ERR(int_port->rx_rule);
+		mlx5_core_warn(esw->dev, "Can't add internal port rx rule, err %d", err);
+		goto err_rx_rule;
+	}
+
+	refcount_set(&int_port->refcnt, 1);
+	list_add_rcu(&int_port->list, &priv->int_ports);
+	priv->num_ports++;
+
+	return int_port;
+
+err_rx_rule:
+	mapping_remove(ctx, int_port->mapping);
+
+err_map:
+	mlx5e_int_port_metadata_free(priv, match_metadata);
+
+err_metadata:
+	kfree(int_port);
+
+	return ERR_PTR(err);
+}
+
+/* Must be called with priv->int_ports_lock held */
+static void
+mlx5e_int_port_remove(struct mlx5e_tc_int_port_priv *priv,
+		      struct mlx5e_tc_int_port *int_port)
+{
+	struct mlx5_eswitch *esw = priv->dev->priv.eswitch;
+	struct mapping_ctx *ctx;
+
+	ctx = esw->offloads.reg_c0_obj_pool;
+
+	list_del_rcu(&int_port->list);
+
+	/* The following parameters are not used by the
+	 * rcu readers of this int_port object so it is
+	 * safe to release them.
+	 */
+	if (int_port->rx_rule)
+		mlx5_del_flow_rules(int_port->rx_rule);
+	mapping_remove(ctx, int_port->mapping);
+	mlx5e_int_port_metadata_free(priv, int_port->match_metadata);
+	kfree_rcu(int_port);
+	priv->num_ports--;
+}
+
+/* Must be called with rcu_read_lock held */
+static struct mlx5e_tc_int_port *
+mlx5e_int_port_get_from_metadata(struct mlx5e_tc_int_port_priv *priv,
+				 u32 metadata)
+{
+	struct mlx5e_tc_int_port *int_port;
+
+	list_for_each_entry_rcu(int_port, &priv->int_ports, list)
+		if (int_port->match_metadata == metadata)
+			return int_port;
+
+	return NULL;
+}
+
+struct mlx5e_tc_int_port *
+mlx5e_tc_int_port_get(struct mlx5e_tc_int_port_priv *priv,
+		      int ifindex,
+		      enum mlx5e_tc_int_port_type type)
+{
+	struct mlx5e_tc_int_port *int_port;
+
+	if (!priv)
+		return ERR_PTR(-EOPNOTSUPP);
+
+	mutex_lock(&priv->int_ports_lock);
+
+	/* Reject request if ul rep not ready */
+	if (!priv->ul_rep_rx_ready) {
+		int_port = ERR_PTR(-EOPNOTSUPP);
+		goto done;
+	}
+
+	int_port = mlx5e_int_port_lookup(priv, ifindex, type);
+	if (int_port)
+		goto done;
+
+	/* Alloc and add new int port to list */
+	int_port = mlx5e_int_port_add(priv, ifindex, type);
+
+done:
+	mutex_unlock(&priv->int_ports_lock);
+
+	return int_port;
+}
+
+void
+mlx5e_tc_int_port_put(struct mlx5e_tc_int_port_priv *priv,
+		      struct mlx5e_tc_int_port *int_port)
+{
+	if (!refcount_dec_and_mutex_lock(&int_port->refcnt, &priv->int_ports_lock))
+		return;
+
+	mlx5e_int_port_remove(priv, int_port);
+	mutex_unlock(&priv->int_ports_lock);
+}
+
+struct mlx5e_tc_int_port_priv *
+mlx5e_tc_int_port_init(struct mlx5e_priv *priv)
+{
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	struct mlx5e_tc_int_port_priv *int_port_priv;
+	u64 mapping_id;
+
+	if (!mlx5e_tc_int_port_supported(esw))
+		return NULL;
+
+	int_port_priv = kzalloc(sizeof(*int_port_priv), GFP_KERNEL);
+	if (!int_port_priv)
+		return NULL;
+
+	mapping_id = mlx5_query_nic_system_image_guid(priv->mdev);
+
+	int_port_priv->metadata_mapping = mapping_create_for_id(mapping_id, MAPPING_TYPE_INT_PORT,
+								sizeof(u32) * 2,
+								(1 << ESW_VPORT_BITS) - 1, true);
+	if (IS_ERR(int_port_priv->metadata_mapping)) {
+		mlx5_core_warn(priv->mdev, "Can't allocate metadata mapping of int port offload, err=%ld\n",
+			       PTR_ERR(int_port_priv->metadata_mapping));
+		goto err_mapping;
+	}
+
+	int_port_priv->dev = priv->mdev;
+	mutex_init(&int_port_priv->int_ports_lock);
+	INIT_LIST_HEAD(&int_port_priv->int_ports);
+
+	return int_port_priv;
+
+err_mapping:
+	kfree(int_port_priv);
+
+	return NULL;
+}
+
+void
+mlx5e_tc_int_port_cleanup(struct mlx5e_tc_int_port_priv *priv)
+{
+	if (!priv)
+		return;
+
+	mutex_destroy(&priv->int_ports_lock);
+	mapping_destroy(priv->metadata_mapping);
+	kfree(priv);
+}
+
+/* Int port rx rules reside in ul rep rx tables.
+ * It is possible the ul rep will go down while there are
+ * still int port rules in its rx table so proper cleanup
+ * is required to free resources.
+ */
+void mlx5e_tc_int_port_init_rep_rx(struct mlx5e_priv *priv)
+{
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	struct mlx5_rep_uplink_priv *uplink_priv;
+	struct mlx5e_tc_int_port_priv *ppriv;
+	struct mlx5e_rep_priv *uplink_rpriv;
+
+	uplink_rpriv = mlx5_eswitch_get_uplink_priv(esw, REP_ETH);
+	uplink_priv = &uplink_rpriv->uplink_priv;
+
+	ppriv = uplink_priv->int_port_priv;
+
+	if (!ppriv)
+		return;
+
+	mutex_lock(&ppriv->int_ports_lock);
+	ppriv->ul_rep_rx_ready = true;
+	mutex_unlock(&ppriv->int_ports_lock);
+}
+
+void mlx5e_tc_int_port_cleanup_rep_rx(struct mlx5e_priv *priv)
+{
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	struct mlx5_rep_uplink_priv *uplink_priv;
+	struct mlx5e_tc_int_port_priv *ppriv;
+	struct mlx5e_rep_priv *uplink_rpriv;
+	struct mlx5e_tc_int_port *int_port;
+
+	uplink_rpriv = mlx5_eswitch_get_uplink_priv(esw, REP_ETH);
+	uplink_priv = &uplink_rpriv->uplink_priv;
+
+	ppriv = uplink_priv->int_port_priv;
+
+	if (!ppriv)
+		return;
+
+	mutex_lock(&ppriv->int_ports_lock);
+
+	ppriv->ul_rep_rx_ready = false;
+
+	list_for_each_entry(int_port, &ppriv->int_ports, list) {
+		if (!IS_ERR_OR_NULL(int_port->rx_rule))
+			mlx5_del_flow_rules(int_port->rx_rule);
+
+		int_port->rx_rule = NULL;
+	}
+
+	mutex_unlock(&ppriv->int_ports_lock);
+}
+
+bool
+mlx5e_tc_int_port_dev_fwd(struct mlx5e_tc_int_port_priv *priv,
+			  struct sk_buff *skb, u32 int_vport_metadata,
+			  bool *forward_tx)
+{
+	enum mlx5e_tc_int_port_type fwd_type;
+	struct mlx5e_tc_int_port *int_port;
+	struct net_device *dev;
+	int ifindex;
+
+	if (!priv)
+		return false;
+
+	rcu_read_lock();
+	int_port = mlx5e_int_port_get_from_metadata(priv, int_vport_metadata);
+	if (!int_port) {
+		rcu_read_unlock();
+		mlx5_core_dbg(priv->dev, "Unable to find int port with metadata 0x%.8x\n",
+			      int_vport_metadata);
+		return false;
+	}
+
+	ifindex = int_port->ifindex;
+	fwd_type = int_port->type;
+	rcu_read_unlock();
+
+	dev = dev_get_by_index(&init_net, ifindex);
+	if (!dev) {
+		mlx5_core_dbg(priv->dev,
+			      "Couldn't find internal port device with ifindex: %d\n",
+			      ifindex);
+		return false;
+	}
+
+	skb->skb_iif = dev->ifindex;
+	skb->dev = dev;
+
+	if (fwd_type == MLX5E_TC_INT_PORT_INGRESS) {
+		skb->pkt_type = PACKET_HOST;
+		skb_set_redirected(skb, true);
+		*forward_tx = false;
+	} else {
+		skb_reset_network_header(skb);
+		skb_push_rcsum(skb, skb->mac_len);
+		skb_set_redirected(skb, false);
+		*forward_tx = true;
+	}
+
+	return true;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc/int_port.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc/int_port.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB */
+/* Copyright (c) 2021, NVIDIA CORPORATION & AFFILIATES. All rights reserved. */
+
+#ifndef __MLX5_EN_TC_INT_PORT_H__
+#define __MLX5_EN_TC_INT_PORT_H__
+
+#include "en.h"
+
+struct mlx5e_tc_int_port;
+struct mlx5e_tc_int_port_priv;
+
+enum mlx5e_tc_int_port_type {
+	MLX5E_TC_INT_PORT_INGRESS,
+	MLX5E_TC_INT_PORT_EGRESS,
+};
+
+#if IS_ENABLED(CONFIG_MLX5_CLS_ACT)
+bool mlx5e_tc_int_port_supported(const struct mlx5_eswitch *esw);
+
+struct mlx5e_tc_int_port_priv *
+mlx5e_tc_int_port_init(struct mlx5e_priv *priv);
+void
+mlx5e_tc_int_port_cleanup(struct mlx5e_tc_int_port_priv *priv);
+
+void mlx5e_tc_int_port_init_rep_rx(struct mlx5e_priv *priv);
+void mlx5e_tc_int_port_cleanup_rep_rx(struct mlx5e_priv *priv);
+
+bool
+mlx5e_tc_int_port_dev_fwd(struct mlx5e_tc_int_port_priv *priv,
+			  struct sk_buff *skb, u32 int_vport_metadata,
+			  bool *forward_tx);
+struct mlx5e_tc_int_port *
+mlx5e_tc_int_port_get(struct mlx5e_tc_int_port_priv *priv,
+		      int ifindex,
+		      enum mlx5e_tc_int_port_type type);
+void
+mlx5e_tc_int_port_put(struct mlx5e_tc_int_port_priv *priv,
+		      struct mlx5e_tc_int_port *int_port);
+
+u32 mlx5e_tc_int_port_get_metadata(struct mlx5e_tc_int_port *int_port);
+u32 mlx5e_tc_int_port_get_metadata_for_match(struct mlx5e_tc_int_port *int_port);
+int mlx5e_tc_int_port_get_flow_source(struct mlx5e_tc_int_port *int_port);
+#else /* CONFIG_MLX5_CLS_ACT */
+static inline u32
+mlx5e_tc_int_port_get_metadata_for_match(struct mlx5e_tc_int_port *int_port)
+{
+		return 0;
+}
+
+static inline int
+mlx5e_tc_int_port_get_flow_source(struct mlx5e_tc_int_port *int_port)
+{
+		return 0;
+}
+
+static inline bool mlx5e_tc_int_port_supported(const struct mlx5_eswitch *esw)
+{
+	return false;
+}
+
+static inline void mlx5e_tc_int_port_init_rep_rx(struct mlx5e_priv *priv) {}
+static inline void mlx5e_tc_int_port_cleanup_rep_rx(struct mlx5e_priv *priv) {}
+
+#endif /* CONFIG_MLX5_CLS_ACT */
+#endif /* __MLX5_EN_TC_INT_PORT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc/sample.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc/sample.c
@@ -5,6 +5,7 @@
 #include <net/psample.h>
 #include "en/mapping.h"
 #include "en/tc/post_act.h"
+#include "en/mod_hdr.h"
 #include "sample.h"
 #include "eswitch.h"
 #include "en_tc.h"
@@ -255,12 +256,12 @@
 		goto err_modify_hdr;
 	}
 
-	dealloc_mod_hdr_actions(&mod_acts);
+	mlx5e_mod_hdr_dealloc(&mod_acts);
 	return modify_hdr;
 
 err_modify_hdr:
 err_post_act:
-	dealloc_mod_hdr_actions(&mod_acts);
+	mlx5e_mod_hdr_dealloc(&mod_acts);
 err_set_regc0:
 	return ERR_PTR(err);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc/sample.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc/sample.h
@@ -19,6 +19,8 @@
 	struct mlx5e_sample_flow *sample_flow;
 };
 
+#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
+
 void mlx5e_tc_sample_skb(struct sk_buff *skb, struct mlx5_mapped_obj *mapped_obj);
 
 struct mlx5_flow_handle *
@@ -38,4 +40,29 @@
 void
 mlx5e_tc_sample_cleanup(struct mlx5e_tc_psample *tc_psample);
 
+#else /* CONFIG_MLX5_TC_SAMPLE */
+
+static inline struct mlx5_flow_handle *
+mlx5e_tc_sample_offload(struct mlx5e_tc_psample *tc_psample,
+			struct mlx5_flow_spec *spec,
+			struct mlx5_flow_attr *attr,
+			u32 tunnel_id)
+{ return ERR_PTR(-EOPNOTSUPP); }
+
+static inline void
+mlx5e_tc_sample_unoffload(struct mlx5e_tc_psample *tc_psample,
+			  struct mlx5_flow_handle *rule,
+			  struct mlx5_flow_attr *attr) {}
+
+static inline struct mlx5e_tc_psample *
+mlx5e_tc_sample_init(struct mlx5_eswitch *esw, struct mlx5e_post_act *post_act)
+{ return ERR_PTR(-EOPNOTSUPP); }
+
+static inline void
+mlx5e_tc_sample_cleanup(struct mlx5e_tc_psample *tc_psample) {}
+
+static inline void
+mlx5e_tc_sample_skb(struct sk_buff *skb, struct mlx5_mapped_obj *mapped_obj) {}
+
+#endif /* CONFIG_MLX5_TC_SAMPLE */
 #endif /* __MLX5_EN_TC_SAMPLE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c
@@ -609,22 +609,15 @@
 	struct flow_action *flow_action = &flow_rule->action;
 	struct mlx5_core_dev *mdev = ct_priv->dev;
 	struct flow_action_entry *act;
-	size_t action_size;
 	char *modact;
 	int err, i;
 
-	action_size = MLX5_UN_SZ_BYTES(set_add_copy_action_in_auto);
-
 	flow_action_for_each(i, act, flow_action) {
 		switch (act->id) {
 		case FLOW_ACTION_MANGLE: {
-			err = alloc_mod_hdr_actions(mdev, ct_priv->ns_type,
-						    mod_acts);
-			if (err)
-				return err;
-
-			modact = mod_acts->actions +
-				 mod_acts->num_actions * action_size;
+			modact = mlx5e_mod_hdr_alloc(mdev, ct_priv->ns_type, mod_acts);
+			if (IS_ERR(modact))
+				return PTR_ERR(modact);
 
 			err = mlx5_tc_ct_parse_mangle_to_mod_act(act, modact);
 			if (err)
@@ -650,7 +643,7 @@
 				struct mlx5_flow_attr *attr,
 				struct flow_rule *flow_rule,
 				struct mlx5e_mod_hdr_handle **mh,
-				u8 zone_restore_id, bool nat)
+				u8 zone_restore_id, bool nat_table, bool has_nat)
 {
 	struct mlx5e_tc_mod_hdr_acts mod_acts = {};
 	struct flow_action_entry *meta;
@@ -665,11 +658,12 @@
 				     &attr->ct_attr.ct_labels_id);
 	if (err)
 		return -EOPNOTSUPP;
-	if (nat) {
-		err = mlx5_tc_ct_entry_create_nat(ct_priv, flow_rule,
-						  &mod_acts);
-		if (err)
-			goto err_mapping;
+	if (nat_table) {
+		if (has_nat) {
+			err = mlx5_tc_ct_entry_create_nat(ct_priv, flow_rule, &mod_acts);
+			if (err)
+				goto err_mapping;
+		}
 
 		ct_state |= MLX5_CT_STATE_NAT_BIT;
 	}
@@ -684,7 +678,7 @@
 	if (err)
 		goto err_mapping;
 
-	if (nat) {
+	if (nat_table && has_nat) {
 		attr->modify_hdr = mlx5_modify_header_alloc(ct_priv->dev, ct_priv->ns_type,
 							    mod_acts.num_actions,
 							    mod_acts.actions);
@@ -706,11 +700,11 @@
 		attr->modify_hdr = mlx5e_mod_hdr_get(*mh);
 	}
 
-	dealloc_mod_hdr_actions(&mod_acts);
+	mlx5e_mod_hdr_dealloc(&mod_acts);
 	return 0;
 
 err_mapping:
-	dealloc_mod_hdr_actions(&mod_acts);
+	mlx5e_mod_hdr_dealloc(&mod_acts);
 	mlx5_put_label_mapping(ct_priv, attr->ct_attr.ct_labels_id);
 	return err;
 }
@@ -752,7 +746,9 @@
 
 	err = mlx5_tc_ct_entry_create_mod_hdr(ct_priv, attr, flow_rule,
 					      &zone_rule->mh,
-					      zone_restore_id, nat);
+					      zone_restore_id,
+					      nat,
+					      mlx5_tc_ct_entry_has_nat(entry));
 	if (err) {
 		ct_dbg("Failed to create ct entry mod hdr");
 		goto err_mod_hdr;
@@ -788,7 +784,7 @@
 	return 0;
 
 err_rule:
-	mlx5_tc_ct_entry_destroy_mod_hdr(ct_priv, zone_rule->attr, zone_rule->mh);
+	mlx5_tc_ct_entry_destroy_mod_hdr(ct_priv, attr, zone_rule->mh);
 	mlx5_put_label_mapping(ct_priv, attr->ct_attr.ct_labels_id);
 err_mod_hdr:
 	kfree(attr);
@@ -1356,9 +1352,13 @@
 int
 mlx5_tc_ct_parse_action(struct mlx5_tc_ct_priv *priv,
 			struct mlx5_flow_attr *attr,
+			struct mlx5e_tc_mod_hdr_acts *mod_acts,
 			const struct flow_action_entry *act,
 			struct netlink_ext_ack *extack)
 {
+	bool clear_action = act->ct.action & TCA_CT_ACT_CLEAR;
+	int err;
+
 	if (!priv) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "offload of ct action isn't available");
@@ -1369,6 +1369,17 @@
 	attr->ct_attr.ct_action = act->ct.action;
 	attr->ct_attr.nf_ft = act->ct.flow_table;
 
+	if (!clear_action)
+		goto out;
+
+	err = mlx5_tc_ct_entry_set_registers(priv, mod_acts, 0, 0, 0, 0);
+	if (err) {
+		NL_SET_ERR_MSG_MOD(extack, "Failed to set registers for ct clear");
+		return err;
+	}
+	attr->action |= MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
+
+out:
 	return 0;
 }
 
@@ -1445,7 +1456,7 @@
 	}
 	pre_ct->miss_rule = rule;
 
-	dealloc_mod_hdr_actions(&pre_mod_acts);
+	mlx5e_mod_hdr_dealloc(&pre_mod_acts);
 	kvfree(spec);
 	return 0;
 
@@ -1454,7 +1465,7 @@
 err_flow_rule:
 	mlx5_modify_header_dealloc(dev, pre_ct->modify_hdr);
 err_mapping:
-	dealloc_mod_hdr_actions(&pre_mod_acts);
+	mlx5e_mod_hdr_dealloc(&pre_mod_acts);
 	kvfree(spec);
 	return err;
 }
@@ -1684,6 +1695,8 @@
 static void
 mlx5_tc_ct_del_ft_cb(struct mlx5_tc_ct_priv *ct_priv, struct mlx5_ct_ft *ft)
 {
+	struct mlx5e_priv *priv;
+
 	if (!refcount_dec_and_test(&ft->refcount))
 		return;
 
@@ -1693,6 +1706,8 @@
 	rhashtable_free_and_destroy(&ft->ct_entries_ht,
 				    mlx5_tc_ct_flush_ft_entry,
 				    ct_priv);
+	priv = netdev_priv(ct_priv->netdev);
+	flush_workqueue(priv->wq);
 	mlx5_tc_ct_free_pre_ct_tables(ft);
 	mapping_remove(ct_priv->zone_mapping, ft->zone_restore_id);
 	kfree(ft);
@@ -1850,14 +1865,14 @@
 	}
 
 	attr->ct_attr.ct_flow = ct_flow;
-	dealloc_mod_hdr_actions(&pre_mod_acts);
+	mlx5e_mod_hdr_dealloc(&pre_mod_acts);
 
 	return ct_flow->pre_ct_rule;
 
 err_insert_orig:
 	mlx5_modify_header_dealloc(priv->mdev, pre_ct_attr->modify_hdr);
 err_mapping:
-	dealloc_mod_hdr_actions(&pre_mod_acts);
+	mlx5e_mod_hdr_dealloc(&pre_mod_acts);
 	mlx5_chains_put_chain_mapping(ct_priv->chains, ct_flow->chain_mapping);
 err_get_chain:
 	kfree(ct_flow->pre_ct_attr);
@@ -1898,23 +1913,16 @@
 
 	memcpy(pre_ct_attr, attr, attr_sz);
 
-	err = mlx5_tc_ct_entry_set_registers(ct_priv, mod_acts, 0, 0, 0, 0);
-	if (err) {
-		ct_dbg("Failed to set register for ct clear");
-		goto err_set_registers;
-	}
-
 	mod_hdr = mlx5_modify_header_alloc(priv->mdev, ct_priv->ns_type,
 					   mod_acts->num_actions,
 					   mod_acts->actions);
 	if (IS_ERR(mod_hdr)) {
 		err = PTR_ERR(mod_hdr);
 		ct_dbg("Failed to add create ct clear mod hdr");
-		goto err_set_registers;
+		goto err_mod_hdr;
 	}
 
 	pre_ct_attr->modify_hdr = mod_hdr;
-	pre_ct_attr->action |= MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
 
 	rule = mlx5_tc_rule_insert(priv, orig_spec, pre_ct_attr);
 	if (IS_ERR(rule)) {
@@ -1930,7 +1938,7 @@
 
 err_insert:
 	mlx5_modify_header_dealloc(priv->mdev, mod_hdr);
-err_set_registers:
+err_mod_hdr:
 	netdev_warn(priv->netdev,
 		    "Failed to offload ct clear flow, err %d\n", err);
 	kfree(pre_ct_attr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.h
@@ -110,6 +110,7 @@
 int
 mlx5_tc_ct_parse_action(struct mlx5_tc_ct_priv *priv,
 			struct mlx5_flow_attr *attr,
+			struct mlx5e_tc_mod_hdr_acts *mod_acts,
 			const struct flow_action_entry *act,
 			struct netlink_ext_ack *extack);
 
@@ -172,6 +173,7 @@
 static inline int
 mlx5_tc_ct_parse_action(struct mlx5_tc_ct_priv *priv,
 			struct mlx5_flow_attr *attr,
+			struct mlx5e_tc_mod_hdr_acts *mod_acts,
 			const struct flow_action_entry *act,
 			struct netlink_ext_ack *extack)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_priv.h
@@ -102,6 +102,7 @@
 	refcount_t refcnt;
 	struct rcu_head rcu_head;
 	struct completion init_done;
+	struct completion del_hw_done;
 	int tunnel_id; /* the mapped tunnel id of this flow */
 	struct mlx5_flow_attr *attr;
 };
@@ -173,4 +174,6 @@
 
 struct mlx5_fc *mlx5e_tc_get_counter(struct mlx5e_tc_flow *flow);
 
+struct mlx5e_tc_int_port_priv *
+mlx5e_get_int_port_priv(struct mlx5e_priv *priv);
 #endif /* __MLX5_EN_TC_PRIV_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c
@@ -1,6 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB */
 /* Copyright (c) 2018 Mellanox Technologies. */
 
+#include <net/inet_ecn.h>
 #include <net/vxlan.h>
 #include <net/gre.h>
 #include <net/geneve.h>
@@ -83,7 +84,8 @@
 	 */
 	*route_dev = dev;
 	if (!netdev_port_same_parent_id(priv->netdev, real_dev) ||
-	    dst_is_lag_dev || is_vlan_dev(*route_dev))
+	    dst_is_lag_dev || is_vlan_dev(*route_dev) ||
+	    netif_is_ovs_master(*route_dev))
 		*out_dev = uplink_dev;
 	else if (mlx5e_eswitch_rep(dev) &&
 		 mlx5e_is_valid_eswitch_fwd_dev(priv, dev))
@@ -229,7 +231,7 @@
 	int err;
 
 	/* add the IP fields */
-	attr.fl.fl4.flowi4_tos = tun_key->tos;
+	attr.fl.fl4.flowi4_tos = tun_key->tos & ~INET_ECN_MASK;
 	attr.fl.fl4.daddr = tun_key->u.ipv4.dst;
 	attr.fl.fl4.saddr = tun_key->u.ipv4.src;
 	attr.ttl = tun_key->ttl;
@@ -344,7 +346,7 @@
 	int err;
 
 	/* add the IP fields */
-	attr.fl.fl4.flowi4_tos = tun_key->tos;
+	attr.fl.fl4.flowi4_tos = tun_key->tos & ~INET_ECN_MASK;
 	attr.fl.fl4.daddr = tun_key->u.ipv4.dst;
 	attr.fl.fl4.saddr = tun_key->u.ipv4.src;
 	attr.ttl = tun_key->ttl;
@@ -496,7 +498,7 @@
 	int err;
 
 	attr.ttl = tun_key->ttl;
-	attr.fl.fl6.flowlabel = ip6_make_flowinfo(RT_TOS(tun_key->tos), tun_key->label);
+	attr.fl.fl6.flowlabel = ip6_make_flowinfo(tun_key->tos, tun_key->label);
 	attr.fl.fl6.daddr = tun_key->u.ipv6.dst;
 	attr.fl.fl6.saddr = tun_key->u.ipv6.src;
 
@@ -610,7 +612,7 @@
 
 	attr.ttl = tun_key->ttl;
 
-	attr.fl.fl6.flowlabel = ip6_make_flowinfo(RT_TOS(tun_key->tos), tun_key->label);
+	attr.fl.fl6.flowlabel = ip6_make_flowinfo(tun_key->tos, tun_key->label);
 	attr.fl.fl6.daddr = tun_key->u.ipv6.dst;
 	attr.fl.fl6.saddr = tun_key->u.ipv6.src;
 
@@ -702,6 +704,8 @@
 			      struct mlx5_flow_attr *flow_attr)
 {
 	struct mlx5_esw_flow_attr *esw_attr = flow_attr->esw_attr;
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	struct mlx5e_tc_int_port *int_port;
 	TC_TUN_ROUTE_ATTR_INIT(attr);
 	u16 vport_num;
 	int err = 0;
@@ -726,17 +730,25 @@
 	if (err)
 		return err;
 
-	if (attr.route_dev->netdev_ops != &mlx5e_netdev_ops ||
-	    !mlx5e_tc_is_vf_tunnel(attr.out_dev, attr.route_dev))
-		goto out;
-
-	err = mlx5e_tc_query_route_vport(attr.out_dev, attr.route_dev, &vport_num);
-	if (err)
-		goto out;
-
-	esw_attr->rx_tun_attr->vni = MLX5_GET(fte_match_param, spec->match_value,
-					      misc_parameters.vxlan_vni);
-	esw_attr->rx_tun_attr->decap_vport = vport_num;
+	if (attr.route_dev->netdev_ops == &mlx5e_netdev_ops &&
+	    mlx5e_tc_is_vf_tunnel(attr.out_dev, attr.route_dev)) {
+		err = mlx5e_tc_query_route_vport(attr.out_dev, attr.route_dev, &vport_num);
+		if (err)
+			goto out;
+
+		esw_attr->rx_tun_attr->vni = MLX5_GET(fte_match_param, spec->match_value,
+						      misc_parameters.vxlan_vni);
+		esw_attr->rx_tun_attr->decap_vport = vport_num;
+	} else if (netif_is_ovs_master(attr.route_dev) && mlx5e_tc_int_port_supported(esw)) {
+		int_port = mlx5e_tc_int_port_get(mlx5e_get_int_port_priv(priv),
+						 attr.route_dev->ifindex,
+						 MLX5E_TC_INT_PORT_INGRESS);
+		if (IS_ERR(int_port)) {
+			err = PTR_ERR(int_port);
+			goto out;
+		}
+		esw_attr->int_port = int_port;
+	}
 
 out:
 	if (flow_attr->tun_ip_version == 4)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun_encap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun_encap.c
@@ -13,6 +13,30 @@
 	MLX5E_ROUTE_ENTRY_VALID     = BIT(0),
 };
 
+static int mlx5e_set_int_port_tunnel(struct mlx5e_priv *priv,
+				     struct mlx5_flow_attr *attr,
+				     struct mlx5e_encap_entry *e,
+				     int out_index)
+{
+	struct net_device *route_dev;
+	int err = 0;
+
+	route_dev = dev_get_by_index(dev_net(e->out_dev), e->route_dev_ifindex);
+
+	if (!route_dev || !netif_is_ovs_master(route_dev))
+		goto out;
+
+	err = mlx5e_set_fwd_to_int_port_actions(priv, attr, e->route_dev_ifindex,
+						MLX5E_TC_INT_PORT_EGRESS,
+						&attr->action, out_index);
+
+out:
+	if (route_dev)
+		dev_put(route_dev);
+
+	return err;
+}
+
 struct mlx5e_route_key {
 	int ip_version;
 	union {
@@ -188,12 +212,19 @@
 	int err;
 
 	list_for_each_entry(flow, flow_list, tmp_list) {
-		if (!mlx5e_is_offloaded_flow(flow) || flow_flag_test(flow, SLOW))
+		if (!mlx5e_is_offloaded_flow(flow))
 			continue;
 		attr = flow->attr;
 		esw_attr = attr->esw_attr;
 		spec = &attr->parse_attr->spec;
 
+		/* Clear pkt_reformat before checking slow path flag. Because
+		 * in next iteration, the same flow is already set slow path
+		 * flag, but still need to clear the pkt_reformat.
+		 */
+		if (flow_flag_test(flow, SLOW))
+			continue;
+
 		/* update from encap rule to slow path rule */
 		rule = mlx5e_tc_offload_to_slow_path(esw, flow, spec);
 		/* mark the flow's encap dest as non-valid */
@@ -221,8 +252,14 @@
 				struct list_head *flow_list,
 				int index)
 {
-	if (IS_ERR(mlx5e_flow_get(flow)))
+	if (IS_ERR(mlx5e_flow_get(flow))) {
+		/* Flow is being deleted concurrently. Wait for it to be
+		 * unoffloaded from hardware, otherwise deleting encap will
+		 * fail.
+		 */
+		wait_for_completion(&flow->del_hw_done);
 		return;
+	}
 	wait_for_completion(&flow->init_done);
 
 	flow->tmp_entry_index = index;
@@ -809,6 +846,17 @@
 	if (err)
 		goto out_err;
 
+	err = mlx5e_set_int_port_tunnel(priv, attr, e, out_index);
+	if (err == -EOPNOTSUPP) {
+		/* If device doesn't support int port offload,
+		 * redirect to uplink vport.
+		 */
+		mlx5_core_dbg(priv->mdev, "attaching int port as encap dev not supported, using uplink\n");
+		err = 0;
+	} else if (err) {
+		goto out_err;
+	}
+
 	flow->encaps[out_index].e = e;
 	list_add(&flow->encaps[out_index].list, &e->flows);
 	flow->encaps[out_index].index = out_index;
@@ -1336,7 +1384,7 @@
 			continue;
 		}
 
-		err = mlx5e_tc_add_flow_mod_hdr(priv, parse_attr, flow);
+		err = mlx5e_tc_add_flow_mod_hdr(priv, flow, attr);
 		if (err) {
 			mlx5_core_warn(priv->mdev, "Failed to update flow mod_hdr err=%d",
 				       err);
@@ -1538,6 +1586,8 @@
 	struct net_device *fib_dev;
 
 	fen_info = container_of(info, struct fib_entry_notifier_info, info);
+	if (fen_info->fi->nh)
+		return NULL;
 	fib_dev = fib_info_nh(fen_info->fi, 0)->fib_nh_dev;
 	if (!fib_dev || fib_dev->netdev_ops != &mlx5e_netdev_ops ||
 	    fen_info->dst_len != 32)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun_mplsoudp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun_mplsoudp.c
@@ -60,37 +60,31 @@
 			void *headers_v)
 {
 	struct flow_rule *rule = flow_cls_offload_flow_rule(f);
-	struct flow_match_enc_keyid enc_keyid;
 	struct flow_match_mpls match;
 	void *misc2_c;
 	void *misc2_v;
 
-	misc2_c = MLX5_ADDR_OF(fte_match_param, spec->match_criteria,
-			       misc_parameters_2);
-	misc2_v = MLX5_ADDR_OF(fte_match_param, spec->match_value,
-			       misc_parameters_2);
-
-	if (!flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_MPLS))
-		return 0;
-
-	if (!flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_ENC_KEYID))
-		return 0;
-
-	flow_rule_match_enc_keyid(rule, &enc_keyid);
-
-	if (!enc_keyid.mask->keyid)
-		return 0;
-
 	if (!MLX5_CAP_ETH(priv->mdev, tunnel_stateless_mpls_over_udp) &&
 	    !(MLX5_CAP_GEN(priv->mdev, flex_parser_protocols) & MLX5_FLEX_PROTO_CW_MPLS_UDP))
 		return -EOPNOTSUPP;
 
+	if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_ENC_KEYID))
+		return -EOPNOTSUPP;
+
+	if (!flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_MPLS))
+		return 0;
+
 	flow_rule_match_mpls(rule, &match);
 
 	/* Only support matching the first LSE */
 	if (match.mask->used_lses != 1)
 		return -EOPNOTSUPP;
 
+	misc2_c = MLX5_ADDR_OF(fte_match_param, spec->match_criteria,
+			       misc_parameters_2);
+	misc2_v = MLX5_ADDR_OF(fte_match_param, spec->match_value,
+			       misc_parameters_2);
+
 	MLX5_SET(fte_match_set_misc2, misc2_c,
 		 outer_first_mpls_over_udp.mpls_label,
 		 match.mask->ls[0].mpls_label);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun_vxlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun_vxlan.c
@@ -88,6 +88,8 @@
 	struct udphdr *udp = (struct udphdr *)(buf);
 	struct vxlanhdr *vxh;
 
+	if (tun_key->tun_flags & TUNNEL_VXLAN_OPT)
+		return -EOPNOTSUPP;
 	vxh = (struct vxlanhdr *)((char *)udp + sizeof(struct udphdr));
 	*ip_proto = IPPROTO_UDP;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tir.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tir.c
@@ -23,6 +23,9 @@
 	struct mlx5e_tir_builder *builder;
 
 	builder = kvzalloc(sizeof(*builder), GFP_KERNEL);
+	if (!builder)
+		return NULL;
+
 	builder->modify = modify;
 
 	return builder;
@@ -70,24 +73,24 @@
 	MLX5_SET(tirc, tirc, tunneled_offload_en, inner_ft_support);
 }
 
-void mlx5e_tir_builder_build_lro(struct mlx5e_tir_builder *builder,
-				 const struct mlx5e_lro_param *lro_param)
+void mlx5e_tir_builder_build_packet_merge(struct mlx5e_tir_builder *builder,
+					  const struct mlx5e_packet_merge_param *pkt_merge_param)
 {
 	void *tirc = mlx5e_tir_builder_get_tirc(builder);
 	const unsigned int rough_max_l2_l3_hdr_sz = 256;
 
 	if (builder->modify)
-		MLX5_SET(modify_tir_in, builder->in, bitmask.lro, 1);
+		MLX5_SET(modify_tir_in, builder->in, bitmask.packet_merge, 1);
 
-	if (!lro_param->enabled)
+	if (pkt_merge_param->type == MLX5E_PACKET_MERGE_NONE)
 		return;
 
-	MLX5_SET(tirc, tirc, lro_enable_mask,
-		 MLX5_TIRC_LRO_ENABLE_MASK_IPV4_LRO |
-		 MLX5_TIRC_LRO_ENABLE_MASK_IPV6_LRO);
+	MLX5_SET(tirc, tirc, packet_merge_mask,
+		 MLX5_TIRC_PACKET_MERGE_MASK_IPV4_LRO |
+		 MLX5_TIRC_PACKET_MERGE_MASK_IPV6_LRO);
 	MLX5_SET(tirc, tirc, lro_max_ip_payload_size,
 		 (MLX5E_PARAMS_DEFAULT_LRO_WQE_SZ - rough_max_l2_l3_hdr_sz) >> 8);
-	MLX5_SET(tirc, tirc, lro_timeout_period_usecs, lro_param->timeout);
+	MLX5_SET(tirc, tirc, lro_timeout_period_usecs, pkt_merge_param->timeout);
 }
 
 static int mlx5e_hfunc_to_hw(u8 hfunc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/tir.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/tir.h
@@ -18,7 +18,7 @@
 };
 
 struct mlx5e_tir_builder;
-struct mlx5e_lro_param;
+struct mlx5e_packet_merge_param;
 
 struct mlx5e_tir_builder *mlx5e_tir_builder_alloc(bool modify);
 void mlx5e_tir_builder_free(struct mlx5e_tir_builder *builder);
@@ -27,8 +27,8 @@
 void mlx5e_tir_builder_build_inline(struct mlx5e_tir_builder *builder, u32 tdn, u32 rqn);
 void mlx5e_tir_builder_build_rqt(struct mlx5e_tir_builder *builder, u32 tdn,
 				 u32 rqtn, bool inner_ft_support);
-void mlx5e_tir_builder_build_lro(struct mlx5e_tir_builder *builder,
-				 const struct mlx5e_lro_param *lro_param);
+void mlx5e_tir_builder_build_packet_merge(struct mlx5e_tir_builder *builder,
+					  const struct mlx5e_packet_merge_param *pkt_merge_param);
 void mlx5e_tir_builder_build_rss(struct mlx5e_tir_builder *builder,
 				 const struct mlx5e_rss_params_hash *rss_hash,
 				 const struct mlx5e_rss_params_traffic_type *rss_tt,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/txrx.h
@@ -74,6 +74,12 @@
 void mlx5e_free_txqsq_descs(struct mlx5e_txqsq *sq);
 
 static inline bool
+mlx5e_skb_fifo_has_room(struct mlx5e_skb_fifo *fifo)
+{
+	return (*fifo->pc - *fifo->cc) < fifo->mask;
+}
+
+static inline bool
 mlx5e_wqc_has_room_for(struct mlx5_wq_cyc *wq, u16 cc, u16 pc, u16 n)
 {
 	return (mlx5_wq_cyc_ctr2ix(wq, cc - pc) >= n) || (cc == pc);
@@ -166,6 +172,8 @@
 	return pi;
 }
 
+void mlx5e_txqsq_wake(struct mlx5e_txqsq *sq);
+
 struct mlx5e_icosq_wqe_info {
 	u8 wqe_type;
 	u8 num_wqebbs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/xsk/pool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/xsk/pool.c
@@ -11,13 +11,13 @@
 {
 	struct device *dev = mlx5_core_dma_dev(priv->mdev);
 
-	return xsk_pool_dma_map(pool, dev, 0);
+	return xsk_pool_dma_map(pool, dev, DMA_ATTR_SKIP_CPU_SYNC);
 }
 
 static void mlx5e_xsk_unmap_pool(struct mlx5e_priv *priv,
 				 struct xsk_buff_pool *pool)
 {
-	return xsk_pool_dma_unmap(pool, 0);
+	return xsk_pool_dma_unmap(pool, DMA_ATTR_SKIP_CPU_SYNC);
 }
 
 static int mlx5e_xsk_get_pools(struct mlx5e_xsk *xsk)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c
@@ -4,6 +4,7 @@
 #include "setup.h"
 #include "en/params.h"
 #include "en/txrx.h"
+#include "en/health.h"
 
 /* It matches XDP_UMEM_MIN_CHUNK_SIZE, but as this constant is private and may
  * change unexpectedly, and mlx5e has a minimum valid stride size for striding
@@ -170,7 +171,13 @@
 
 void mlx5e_activate_xsk(struct mlx5e_channel *c)
 {
+	/* ICOSQ recovery deactivates RQs. Suspend the recovery to avoid
+	 * activating XSKRQ in the middle of recovery.
+	 */
+	mlx5e_reporter_icosq_suspend_recovery(c);
 	set_bit(MLX5E_RQ_STATE_ENABLED, &c->xskrq.state);
+	mlx5e_reporter_icosq_resume_recovery(c);
+
 	/* TX queue is created active. */
 
 	spin_lock_bh(&c->async_icosq_lock);
@@ -180,6 +187,13 @@
 
 void mlx5e_deactivate_xsk(struct mlx5e_channel *c)
 {
-	mlx5e_deactivate_rq(&c->xskrq);
+	/* ICOSQ recovery may reactivate XSKRQ if clear_bit is called in the
+	 * middle of recovery. Suspend the recovery to avoid it.
+	 */
+	mlx5e_reporter_icosq_suspend_recovery(c);
+	clear_bit(MLX5E_RQ_STATE_ENABLED, &c->xskrq.state);
+	mlx5e_reporter_icosq_resume_recovery(c);
+	synchronize_net(); /* Sync with NAPI to prevent mlx5e_post_rx_wqes. */
+
 	/* TX queue is disabled on close. */
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/fs_tcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/fs_tcp.c
@@ -194,6 +194,7 @@
 	in = kvzalloc(inlen, GFP_KERNEL);
 	if  (!in || !ft->g) {
 		kfree(ft->g);
+		ft->g = NULL;
 		kvfree(in);
 		return -ENOMEM;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec.c
@@ -113,7 +113,6 @@
 	struct xfrm_replay_state_esn *replay_esn;
 	u32 seq_bottom = 0;
 	u8 overlap;
-	u32 *esn;
 
 	if (!(sa_entry->x->props.flags & XFRM_STATE_ESN)) {
 		sa_entry->esn_state.trigger = 0;
@@ -128,11 +127,9 @@
 
 	sa_entry->esn_state.esn = xfrm_replay_seqhi(sa_entry->x,
 						    htonl(seq_bottom));
-	esn = &sa_entry->esn_state.esn;
 
 	sa_entry->esn_state.trigger = 1;
 	if (unlikely(overlap && seq_bottom < MLX5E_IPSEC_ESN_SCOPE_MID)) {
-		++(*esn);
 		sa_entry->esn_state.overlap = 0;
 		return true;
 	} else if (unlikely(!overlap &&
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.c
@@ -121,7 +121,9 @@
 
 	trailer_len = alen + plen + 2;
 
-	pskb_trim(skb, skb->len - trailer_len);
+	ret = pskb_trim(skb, skb->len - trailer_len);
+	if (unlikely(ret))
+		return ret;
 	if (skb->protocol == htons(ETH_P_IP)) {
 		ipv4hdr->tot_len = htons(ntohs(ipv4hdr->tot_len) - trailer_len);
 		ip_send_check(ipv4hdr);
@@ -157,11 +159,20 @@
 	/* Tunnel mode */
 	if (mode == XFRM_MODE_TUNNEL) {
 		eseg->swp_inner_l3_offset = skb_inner_network_offset(skb) / 2;
-		eseg->swp_inner_l4_offset = skb_inner_transport_offset(skb) / 2;
 		if (xo->proto == IPPROTO_IPV6)
 			eseg->swp_flags |= MLX5_ETH_WQE_SWP_INNER_L3_IPV6;
-		if (inner_ip_hdr(skb)->protocol == IPPROTO_UDP)
+
+		switch (xo->inner_ipproto) {
+		case IPPROTO_UDP:
 			eseg->swp_flags |= MLX5_ETH_WQE_SWP_INNER_L4_UDP;
+			fallthrough;
+		case IPPROTO_TCP:
+			/* IP | ESP | IP | [TCP | UDP] */
+			eseg->swp_inner_l4_offset = skb_inner_transport_offset(skb) / 2;
+			break;
+		default:
+			break;
+		}
 		return;
 	}
 
@@ -191,7 +202,7 @@
 			eseg->swp_inner_l3_offset = skb_inner_network_offset(skb) / 2;
 			eseg->swp_inner_l4_offset =
 				(skb->csum_start + skb->head - skb->data) / 2;
-			if (skb->protocol == htons(ETH_P_IPV6))
+			if (inner_ip_hdr(skb)->version == 6)
 				eseg->swp_flags |= MLX5_ETH_WQE_SWP_INNER_L3_IPV6;
 			break;
 		default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.h
@@ -105,18 +105,11 @@
 		if (!x || !x->xso.offload_handle)
 			goto out_disable;
 
-		if (xo->inner_ipproto) {
-			/* Cannot support tunnel packet over IPsec tunnel mode
-			 * because we cannot offload three IP header csum
-			 */
-			if (x->props.mode == XFRM_MODE_TUNNEL)
-				goto out_disable;
-
-			/* Only support UDP or TCP L4 checksum */
-			if (xo->inner_ipproto != IPPROTO_UDP &&
-			    xo->inner_ipproto != IPPROTO_TCP)
-				goto out_disable;
-		}
+		/* Only support UDP or TCP L4 checksum */
+		if (xo->inner_ipproto &&
+		    xo->inner_ipproto != IPPROTO_UDP &&
+		    xo->inner_ipproto != IPPROTO_TCP)
+			goto out_disable;
 
 		return features;
 
@@ -127,6 +120,28 @@
 	return features & ~(NETIF_F_CSUM_MASK | NETIF_F_GSO_MASK);
 }
 
+static inline bool
+mlx5e_ipsec_txwqe_build_eseg_csum(struct mlx5e_txqsq *sq, struct sk_buff *skb,
+				  struct mlx5_wqe_eth_seg *eseg)
+{
+	u8 inner_ipproto;
+
+	if (!mlx5e_ipsec_eseg_meta(eseg))
+		return false;
+
+	eseg->cs_flags = MLX5_ETH_WQE_L3_CSUM;
+	inner_ipproto = xfrm_offload(skb)->inner_ipproto;
+	if (inner_ipproto) {
+		eseg->cs_flags |= MLX5_ETH_WQE_L3_INNER_CSUM;
+		if (inner_ipproto == IPPROTO_TCP || inner_ipproto == IPPROTO_UDP)
+			eseg->cs_flags |= MLX5_ETH_WQE_L4_INNER_CSUM;
+	} else if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
+		eseg->cs_flags |= MLX5_ETH_WQE_L4_CSUM;
+		sq->stats->csum_partial_inner++;
+	}
+
+	return true;
+}
 #else
 static inline
 void mlx5e_ipsec_offload_handle_rx_skb(struct net_device *netdev,
@@ -143,6 +158,13 @@
 static inline netdev_features_t
 mlx5e_ipsec_feature_check(struct sk_buff *skb, netdev_features_t features)
 { return features & ~(NETIF_F_CSUM_MASK | NETIF_F_GSO_MASK); }
+
+static inline bool
+mlx5e_ipsec_txwqe_build_eseg_csum(struct mlx5e_txqsq *sq, struct sk_buff *skb,
+				  struct mlx5_wqe_eth_seg *eseg)
+{
+	return false;
+}
 #endif /* CONFIG_MLX5_EN_IPSEC */
 
 #endif /* __MLX5E_IPSEC_RXTX_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls.c
@@ -16,7 +16,7 @@
 	struct mlx5_core_dev *mdev = priv->mdev;
 	int err;
 
-	if (WARN_ON(!mlx5e_ktls_type_check(mdev, crypto_info)))
+	if (!mlx5e_ktls_type_check(mdev, crypto_info))
 		return -EOPNOTSUPP;
 
 	if (direction == TLS_OFFLOAD_CTX_DIR_TX)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_rx.c
@@ -55,6 +55,7 @@
 	DECLARE_BITMAP(flags, MLX5E_NUM_PRIV_RX_FLAGS);
 
 	/* resync */
+	spinlock_t lock; /* protects resync fields */
 	struct mlx5e_ktls_rx_resync_ctx resync;
 	struct list_head list;
 };
@@ -99,25 +100,6 @@
 	return resp_list;
 }
 
-static int mlx5e_ktls_create_tir(struct mlx5_core_dev *mdev, struct mlx5e_tir *tir, u32 rqtn)
-{
-	struct mlx5e_tir_builder *builder;
-	int err;
-
-	builder = mlx5e_tir_builder_alloc(false);
-	if (!builder)
-		return -ENOMEM;
-
-	mlx5e_tir_builder_build_rqt(builder, mdev->mlx5e_res.hw_objs.td.tdn, rqtn, false);
-	mlx5e_tir_builder_build_direct(builder);
-	mlx5e_tir_builder_build_tls(builder);
-	err = mlx5e_tir_init(tir, builder, mdev, false);
-
-	mlx5e_tir_builder_free(builder);
-
-	return err;
-}
-
 static void accel_rule_handle_work(struct work_struct *work)
 {
 	struct mlx5e_ktls_offload_context_rx *priv_rx;
@@ -249,8 +231,7 @@
 	struct mlx5e_ktls_offload_context_rx **ctx =
 		__tls_driver_ctx(tls_ctx, TLS_OFFLOAD_CTX_DIR_RX);
 
-	BUILD_BUG_ON(sizeof(struct mlx5e_ktls_offload_context_rx *) >
-		     TLS_OFFLOAD_CONTEXT_SIZE_RX);
+	BUILD_BUG_ON(sizeof(priv_rx) > TLS_DRIVER_STATE_SIZE_RX);
 
 	*ctx = priv_rx;
 }
@@ -386,14 +367,18 @@
 	struct mlx5e_icosq *sq;
 	bool trigger_poll;
 
-	memcpy(info->rec_seq, &priv_rx->resync.sw_rcd_sn_be, sizeof(info->rec_seq));
-
 	sq = &c->async_icosq;
 	ktls_resync = sq->ktls_resync;
+	trigger_poll = false;
 
 	spin_lock_bh(&ktls_resync->lock);
-	list_add_tail(&priv_rx->list, &ktls_resync->list);
-	trigger_poll = !test_and_set_bit(MLX5E_SQ_STATE_PENDING_TLS_RX_RESYNC, &sq->state);
+	spin_lock_bh(&priv_rx->lock);
+	memcpy(info->rec_seq, &priv_rx->resync.sw_rcd_sn_be, sizeof(info->rec_seq));
+	if (list_empty(&priv_rx->list)) {
+		list_add_tail(&priv_rx->list, &ktls_resync->list);
+		trigger_poll = !test_and_set_bit(MLX5E_SQ_STATE_PENDING_TLS_RX_RESYNC, &sq->state);
+	}
+	spin_unlock_bh(&priv_rx->lock);
 	spin_unlock_bh(&ktls_resync->lock);
 
 	if (!trigger_poll)
@@ -604,7 +589,6 @@
 	struct mlx5_core_dev *mdev;
 	struct mlx5e_priv *priv;
 	int rxq, err;
-	u32 rqtn;
 
 	tls_ctx = tls_get_ctx(sk);
 	priv = netdev_priv(netdev);
@@ -617,6 +601,8 @@
 	if (err)
 		goto err_create_key;
 
+	INIT_LIST_HEAD(&priv_rx->list);
+	spin_lock_init(&priv_rx->lock);
 	priv_rx->crypto_info  =
 		*(struct tls12_crypto_info_aes_gcm_128 *)crypto_info;
 
@@ -628,9 +614,7 @@
 	priv_rx->sw_stats = &priv->tls->sw_stats;
 	mlx5e_set_ktls_rx_priv_ctx(tls_ctx, priv_rx);
 
-	rqtn = mlx5e_rx_res_get_rqtn_direct(priv->rx_res, rxq);
-
-	err = mlx5e_ktls_create_tir(mdev, &priv_rx->tir, rqtn);
+	err = mlx5e_rx_res_tls_tir_create(priv->rx_res, rxq, &priv_rx->tir);
 	if (err)
 		goto err_create_tir;
 
@@ -730,10 +714,14 @@
 		priv_rx = list_first_entry(&local_list,
 					   struct mlx5e_ktls_offload_context_rx,
 					   list);
+		spin_lock(&priv_rx->lock);
 		cseg = post_static_params(sq, priv_rx);
-		if (IS_ERR(cseg))
+		if (IS_ERR(cseg)) {
+			spin_unlock(&priv_rx->lock);
 			break;
-		list_del(&priv_rx->list);
+		}
+		list_del_init(&priv_rx->list);
+		spin_unlock(&priv_rx->lock);
 		db_cseg = cseg;
 	}
 	if (db_cseg)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c
@@ -68,8 +68,7 @@
 	struct mlx5e_ktls_offload_context_tx **ctx =
 		__tls_driver_ctx(tls_ctx, TLS_OFFLOAD_CTX_DIR_TX);
 
-	BUILD_BUG_ON(sizeof(struct mlx5e_ktls_offload_context_tx *) >
-		     TLS_OFFLOAD_CONTEXT_SIZE_TX);
+	BUILD_BUG_ON(sizeof(priv_tx) > TLS_DRIVER_STATE_SIZE_TX);
 
 	*ctx = priv_tx;
 }
@@ -270,7 +269,7 @@
 	while (remaining > 0) {
 		skb_frag_t *frag = &record->frags[i];
 
-		get_page(skb_frag_page(frag));
+		page_ref_inc(skb_frag_page(frag));
 		remaining -= skb_frag_size(frag);
 		info->frags[i++] = *frag;
 	}
@@ -357,7 +356,7 @@
 	stats = sq->stats;
 
 	mlx5e_tx_dma_unmap(sq->pdev, dma);
-	put_page(wi->resync_dump_frag_page);
+	page_ref_dec(wi->resync_dump_frag_page);
 	stats->tls_dump_packets++;
 	stats->tls_dump_bytes += wi->num_bytes;
 }
@@ -438,12 +437,12 @@
 
 err_out:
 	for (; i < info.nr_frags; i++)
-		/* The put_page() here undoes the page ref obtained in tx_sync_info_get().
+		/* The page_ref_dec() here undoes the page ref obtained in tx_sync_info_get().
 		 * Page refs obtained for the DUMP WQEs above (by page_ref_add) will be
 		 * released only upon their completions (or in mlx5e_free_txqsq_descs,
 		 * if channel closes).
 		 */
-		put_page(skb_frag_page(&info.frags[i]));
+		page_ref_dec(skb_frag_page(&info.frags[i]));
 
 	return MLX5E_KTLS_SYNC_FAIL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_arfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_arfs.c
@@ -239,11 +239,13 @@
 
 	ft->g = kcalloc(MLX5E_ARFS_NUM_GROUPS,
 			sizeof(*ft->g), GFP_KERNEL);
-	in = kvzalloc(inlen, GFP_KERNEL);
-	if  (!in || !ft->g) {
-		kfree(ft->g);
-		kvfree(in);
+	if (!ft->g)
 		return -ENOMEM;
+
+	in = kvzalloc(inlen, GFP_KERNEL);
+	if (!in) {
+		err = -ENOMEM;
+		goto err_free_g;
 	}
 
 	mc = MLX5_ADDR_OF(create_flow_group_in, in, match_criteria);
@@ -263,7 +265,7 @@
 		break;
 	default:
 		err = -EINVAL;
-		goto out;
+		goto err_free_in;
 	}
 
 	switch (type) {
@@ -285,7 +287,7 @@
 		break;
 	default:
 		err = -EINVAL;
-		goto out;
+		goto err_free_in;
 	}
 
 	MLX5_SET_CFG(in, match_criteria_enable, MLX5_MATCH_OUTER_HEADERS);
@@ -294,7 +296,7 @@
 	MLX5_SET_CFG(in, end_flow_index, ix - 1);
 	ft->g[ft->num_groups] = mlx5_create_flow_group(ft->t, in);
 	if (IS_ERR(ft->g[ft->num_groups]))
-		goto err;
+		goto err_clean_group;
 	ft->num_groups++;
 
 	memset(in, 0, inlen);
@@ -303,18 +305,20 @@
 	MLX5_SET_CFG(in, end_flow_index, ix - 1);
 	ft->g[ft->num_groups] = mlx5_create_flow_group(ft->t, in);
 	if (IS_ERR(ft->g[ft->num_groups]))
-		goto err;
+		goto err_clean_group;
 	ft->num_groups++;
 
 	kvfree(in);
 	return 0;
 
-err:
+err_clean_group:
 	err = PTR_ERR(ft->g[ft->num_groups]);
 	ft->g[ft->num_groups] = NULL;
-out:
+err_free_in:
 	kvfree(in);
-
+err_free_g:
+	kfree(ft->g);
+	ft->g = NULL;
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_common.c
@@ -140,10 +140,8 @@
 
 	inlen = MLX5_ST_SZ_BYTES(modify_tir_in);
 	in = kvzalloc(inlen, GFP_KERNEL);
-	if (!in) {
-		err = -ENOMEM;
-		goto out;
-	}
+	if (!in)
+		return -ENOMEM;
 
 	if (enable_uc_lb)
 		lb_flags = MLX5_TIRC_SELF_LB_BLOCK_BLOCK_UNICAST;
@@ -161,14 +159,13 @@
 		tirn = tir->tirn;
 		err = mlx5_core_modify_tir(mdev, tirn, in);
 		if (err)
-			goto out;
+			break;
 	}
+	mutex_unlock(&mdev->mlx5e_res.hw_objs.td.list_lock);
 
-out:
 	kvfree(in);
 	if (err)
 		netdev_err(priv->netdev, "refresh tir(0x%x) failed, %d\n", tirn, err);
-	mutex_unlock(&mdev->mlx5e_res.hw_objs.td.list_lock);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c
@@ -117,12 +117,14 @@
 	if (!MLX5_CAP_GEN(priv->mdev, ets))
 		return -EOPNOTSUPP;
 
-	ets->ets_cap = mlx5_max_tc(priv->mdev) + 1;
-	for (i = 0; i < ets->ets_cap; i++) {
+	for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
 		err = mlx5_query_port_prio_tc(mdev, i, &ets->prio_tc[i]);
 		if (err)
 			return err;
+	}
 
+	ets->ets_cap = mlx5_max_tc(priv->mdev) + 1;
+	for (i = 0; i < ets->ets_cap; i++) {
 		err = mlx5_query_port_tc_group(mdev, i, &tc_group[i]);
 		if (err)
 			return err;
@@ -1198,6 +1200,16 @@
 	if (err)
 		return err;
 
+	if (priv->dcbx_dp.trust_state == MLX5_QPTS_TRUST_PCP && priv->dcbx.dscp_app_cnt) {
+		/*
+		 * Align the driver state with the register state.
+		 * Temporary state change is required to enable the app list reset.
+		 */
+		priv->dcbx_dp.trust_state = MLX5_QPTS_TRUST_DSCP;
+		mlx5e_dcbnl_delete_app(priv);
+		priv->dcbx_dp.trust_state = MLX5_QPTS_TRUST_PCP;
+	}
+
 	mlx5e_params_calc_trust_tx_min_inline_mode(priv->mdev, &priv->channels.params,
 						   priv->dcbx_dp.trust_state);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
@@ -129,6 +129,10 @@
 				       ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT);
 	MLX5_BUILD_PTYS2ETHTOOL_CONFIG(MLX5E_100GBASE_LR4, legacy,
 				       ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT);
+	MLX5_BUILD_PTYS2ETHTOOL_CONFIG(MLX5E_100BASE_TX, legacy,
+				       ETHTOOL_LINK_MODE_100baseT_Full_BIT);
+	MLX5_BUILD_PTYS2ETHTOOL_CONFIG(MLX5E_1000BASE_T, legacy,
+				       ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
 	MLX5_BUILD_PTYS2ETHTOOL_CONFIG(MLX5E_10GBASE_T, legacy,
 				       ETHTOOL_LINK_MODE_10000baseT_Full_BIT);
 	MLX5_BUILD_PTYS2ETHTOOL_CONFIG(MLX5E_25GBASE_CR, legacy,
@@ -1181,7 +1185,12 @@
 	if (!an_changes && link_modes == eproto.admin)
 		goto out;
 
-	mlx5_port_set_eth_ptys(mdev, an_disable, link_modes, ext);
+	err = mlx5_port_set_eth_ptys(mdev, an_disable, link_modes, ext);
+	if (err) {
+		netdev_err(priv->netdev, "%s: failed to set ptys reg: %d\n", __func__, err);
+		goto out;
+	}
+
 	mlx5_toggle_port_link(mdev);
 
 out:
@@ -1754,7 +1763,7 @@
 		if (size_read < 0) {
 			netdev_err(priv->netdev, "%s: mlx5_query_eeprom failed:0x%x\n",
 				   __func__, size_read);
-			return 0;
+			return size_read;
 		}
 
 		i += size_read;
@@ -1954,8 +1963,8 @@
 			return -EOPNOTSUPP;
 		if (!mlx5e_striding_rq_possible(mdev, &priv->channels.params))
 			return -EINVAL;
-	} else if (priv->channels.params.lro_en) {
-		netdev_warn(netdev, "Can't set legacy RQ with LRO, disable LRO first\n");
+	} else if (priv->channels.params.packet_merge.type != MLX5E_PACKET_MERGE_NONE) {
+		netdev_warn(netdev, "Can't set legacy RQ with HW-GRO/LRO, disable them first\n");
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_fs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_fs.c
@@ -71,12 +71,12 @@
 	bool   mpfs;
 };
 
-static inline int mlx5e_hash_l2(u8 *addr)
+static inline int mlx5e_hash_l2(const u8 *addr)
 {
 	return addr[5];
 }
 
-static void mlx5e_add_l2_to_hash(struct hlist_head *hash, u8 *addr)
+static void mlx5e_add_l2_to_hash(struct hlist_head *hash, const u8 *addr)
 {
 	struct mlx5e_l2_hash_node *hn;
 	int ix = mlx5e_hash_l2(addr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_fs_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_fs_ethtool.c
@@ -411,7 +411,7 @@
 			 u32 rss_context, u32 *tirn)
 {
 	if (fs->flow_type & FLOW_RSS) {
-		struct mlx5e_lro_param lro_param;
+		struct mlx5e_packet_merge_param pkt_merge_param;
 		struct mlx5e_rss *rss;
 		u32 flow_type;
 		int err;
@@ -426,8 +426,8 @@
 		if (tt < 0)
 			return -EINVAL;
 
-		lro_param = mlx5e_get_lro_param(&priv->channels.params);
-		err = mlx5e_rss_obtain_tirn(rss, tt, &lro_param, false, tirn);
+		pkt_merge_param = priv->channels.params.packet_merge;
+		err = mlx5e_rss_obtain_tirn(rss, tt, &pkt_merge_param, false, tirn);
 		if (err)
 			return err;
 		eth_rule->rss = rss;
@@ -727,7 +727,7 @@
 	if (num_tuples <= 0) {
 		netdev_warn(priv->netdev, "%s: flow is not valid %d\n",
 			    __func__, num_tuples);
-		return num_tuples;
+		return num_tuples < 0 ? num_tuples : -EINVAL;
 	}
 
 	eth_ft = get_flow_table(priv, fs, num_tuples);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
@@ -392,7 +392,8 @@
 	rq->icosq        = &c->icosq;
 	rq->ix           = c->ix;
 	rq->mdev         = mdev;
-	rq->hw_mtu       = MLX5E_SW2HW_MTU(params, params->sw_mtu);
+	rq->hw_mtu =
+		MLX5E_SW2HW_MTU(params, params->sw_mtu) - ETH_FCS_LEN * !params->scatter_fcs_en;
 	rq->xdpsq        = &c->rq_xdpsq;
 	rq->stats        = &c->priv->channel_stats[c->ix].rq;
 	rq->ptp_cyc2time = mlx5_rq_ts_translator(mdev);
@@ -672,7 +673,7 @@
 	return err;
 }
 
-int mlx5e_modify_rq_state(struct mlx5e_rq *rq, int curr_state, int next_state)
+static int mlx5e_modify_rq_state(struct mlx5e_rq *rq, int curr_state, int next_state)
 {
 	struct mlx5_core_dev *mdev = rq->mdev;
 
@@ -701,33 +702,30 @@
 	return err;
 }
 
-static int mlx5e_modify_rq_scatter_fcs(struct mlx5e_rq *rq, bool enable)
+static int mlx5e_rq_to_ready(struct mlx5e_rq *rq, int curr_state)
 {
-	struct mlx5_core_dev *mdev = rq->mdev;
-
-	void *in;
-	void *rqc;
-	int inlen;
+	struct net_device *dev = rq->netdev;
 	int err;
 
-	inlen = MLX5_ST_SZ_BYTES(modify_rq_in);
-	in = kvzalloc(inlen, GFP_KERNEL);
-	if (!in)
-		return -ENOMEM;
-
-	rqc = MLX5_ADDR_OF(modify_rq_in, in, ctx);
-
-	MLX5_SET(modify_rq_in, in, rq_state, MLX5_RQC_STATE_RDY);
-	MLX5_SET64(modify_rq_in, in, modify_bitmask,
-		   MLX5_MODIFY_RQ_IN_MODIFY_BITMASK_SCATTER_FCS);
-	MLX5_SET(rqc, rqc, scatter_fcs, enable);
-	MLX5_SET(rqc, rqc, state, MLX5_RQC_STATE_RDY);
+	err = mlx5e_modify_rq_state(rq, curr_state, MLX5_RQC_STATE_RST);
+	if (err) {
+		netdev_err(dev, "Failed to move rq 0x%x to reset\n", rq->rqn);
+		return err;
+	}
+	err = mlx5e_modify_rq_state(rq, MLX5_RQC_STATE_RST, MLX5_RQC_STATE_RDY);
+	if (err) {
+		netdev_err(dev, "Failed to move rq 0x%x to ready\n", rq->rqn);
+		return err;
+	}
 
-	err = mlx5_core_modify_rq(mdev, rq->rqn, in);
+	return 0;
+}
 
-	kvfree(in);
+int mlx5e_flush_rq(struct mlx5e_rq *rq, int curr_state)
+{
+	mlx5e_free_rx_descs(rq);
 
-	return err;
+	return mlx5e_rq_to_ready(rq, curr_state);
 }
 
 static int mlx5e_modify_rq_vsd(struct mlx5e_rq *rq, bool vsd)
@@ -911,8 +909,6 @@
 void mlx5e_close_rq(struct mlx5e_rq *rq)
 {
 	cancel_work_sync(&rq->dim.work);
-	if (rq->icosq)
-		cancel_work_sync(&rq->icosq->recover_work);
 	cancel_work_sync(&rq->recover_work);
 	mlx5e_destroy_rq(rq);
 	mlx5e_free_rx_descs(rq);
@@ -979,7 +975,7 @@
 	sq->channel   = c;
 	sq->uar_map   = mdev->mlx5e_res.hw_objs.bfreg.map;
 	sq->min_inline_mode = params->tx_min_inline_mode;
-	sq->hw_mtu    = MLX5E_SW2HW_MTU(params, params->sw_mtu);
+	sq->hw_mtu    = MLX5E_SW2HW_MTU(params, params->sw_mtu) - ETH_FCS_LEN;
 	sq->xsk_pool  = xsk_pool;
 
 	sq->stats = sq->xsk_pool ?
@@ -1038,9 +1034,20 @@
 	mlx5e_reporter_icosq_cqe_err(sq);
 }
 
+static void mlx5e_async_icosq_err_cqe_work(struct work_struct *recover_work)
+{
+	struct mlx5e_icosq *sq = container_of(recover_work, struct mlx5e_icosq,
+					      recover_work);
+
+	/* Not implemented yet. */
+
+	netdev_warn(sq->channel->netdev, "async_icosq recovery is not implemented\n");
+}
+
 static int mlx5e_alloc_icosq(struct mlx5e_channel *c,
 			     struct mlx5e_sq_param *param,
-			     struct mlx5e_icosq *sq)
+			     struct mlx5e_icosq *sq,
+			     work_func_t recover_work_func)
 {
 	void *sqc_wq               = MLX5_ADDR_OF(sqc, param->sqc, wq);
 	struct mlx5_core_dev *mdev = c->mdev;
@@ -1061,7 +1068,7 @@
 	if (err)
 		goto err_sq_wq_destroy;
 
-	INIT_WORK(&sq->recover_work, mlx5e_icosq_err_cqe_work);
+	INIT_WORK(&sq->recover_work, recover_work_func);
 
 	return 0;
 
@@ -1399,13 +1406,14 @@
 	mlx5e_reporter_tx_err_cqe(sq);
 }
 
-int mlx5e_open_icosq(struct mlx5e_channel *c, struct mlx5e_params *params,
-		     struct mlx5e_sq_param *param, struct mlx5e_icosq *sq)
+static int mlx5e_open_icosq(struct mlx5e_channel *c, struct mlx5e_params *params,
+			    struct mlx5e_sq_param *param, struct mlx5e_icosq *sq,
+			    work_func_t recover_work_func)
 {
 	struct mlx5e_create_sq_param csp = {};
 	int err;
 
-	err = mlx5e_alloc_icosq(c, param, sq);
+	err = mlx5e_alloc_icosq(c, param, sq, recover_work_func);
 	if (err)
 		return err;
 
@@ -1444,7 +1452,7 @@
 	synchronize_net(); /* Sync with NAPI. */
 }
 
-void mlx5e_close_icosq(struct mlx5e_icosq *sq)
+static void mlx5e_close_icosq(struct mlx5e_icosq *sq)
 {
 	struct mlx5e_channel *c = sq->channel;
 
@@ -1871,11 +1879,15 @@
 
 	spin_lock_init(&c->async_icosq_lock);
 
-	err = mlx5e_open_icosq(c, params, &cparam->async_icosq, &c->async_icosq);
+	err = mlx5e_open_icosq(c, params, &cparam->async_icosq, &c->async_icosq,
+			       mlx5e_async_icosq_err_cqe_work);
 	if (err)
 		goto err_close_xdpsq_cq;
 
-	err = mlx5e_open_icosq(c, params, &cparam->icosq, &c->icosq);
+	mutex_init(&c->icosq_recovery_lock);
+
+	err = mlx5e_open_icosq(c, params, &cparam->icosq, &c->icosq,
+			       mlx5e_icosq_err_cqe_work);
 	if (err)
 		goto err_close_async_icosq;
 
@@ -1943,9 +1955,12 @@
 	mlx5e_close_xdpsq(&c->xdpsq);
 	if (c->xdp)
 		mlx5e_close_xdpsq(&c->rq_xdpsq);
+	/* The same ICOSQ is used for UMRs for both RQ and XSKRQ. */
+	cancel_work_sync(&c->icosq.recover_work);
 	mlx5e_close_rq(&c->rq);
 	mlx5e_close_sqs(c);
 	mlx5e_close_icosq(&c->icosq);
+	mutex_destroy(&c->icosq_recovery_lock);
 	mlx5e_close_icosq(&c->async_icosq);
 	if (c->xdp)
 		mlx5e_close_cq(&c->rq_xdpsq.cq);
@@ -2185,17 +2200,14 @@
 	chs->num = 0;
 }
 
-static int mlx5e_modify_tirs_lro(struct mlx5e_priv *priv)
+static int mlx5e_modify_tirs_packet_merge(struct mlx5e_priv *priv)
 {
 	struct mlx5e_rx_res *res = priv->rx_res;
-	struct mlx5e_lro_param lro_param;
-
-	lro_param = mlx5e_get_lro_param(&priv->channels.params);
 
-	return mlx5e_rx_res_lro_set_param(res, &lro_param);
+	return mlx5e_rx_res_packet_merge_set_param(res, &priv->channels.params.packet_merge);
 }
 
-static MLX5E_DEFINE_PREACTIVATE_WRAPPER_CTX(mlx5e_modify_tirs_lro);
+static MLX5E_DEFINE_PREACTIVATE_WRAPPER_CTX(mlx5e_modify_tirs_packet_merge);
 
 static int mlx5e_set_mtu(struct mlx5_core_dev *mdev,
 			 struct mlx5e_params *params, u16 mtu)
@@ -2836,20 +2848,6 @@
 	mlx5e_destroy_tises(priv);
 }
 
-static int mlx5e_modify_channels_scatter_fcs(struct mlx5e_channels *chs, bool enable)
-{
-	int err = 0;
-	int i;
-
-	for (i = 0; i < chs->num; i++) {
-		err = mlx5e_modify_rq_scatter_fcs(&chs->c[i]->rq, enable);
-		if (err)
-			return err;
-	}
-
-	return 0;
-}
-
 static int mlx5e_modify_channels_vsd(struct mlx5e_channels *chs, bool vsd)
 {
 	int err;
@@ -3187,7 +3185,7 @@
 		mlx5e_fold_sw_stats64(priv, stats);
 	}
 
-	stats->rx_dropped = priv->stats.qcnt.rx_out_of_buffer;
+	stats->rx_missed_errors = priv->stats.qcnt.rx_out_of_buffer;
 
 	stats->rx_length_errors =
 		PPORT_802_3_GET(pstats, a_in_range_length_errors) +
@@ -3226,7 +3224,7 @@
 		return -EADDRNOTAVAIL;
 
 	netif_addr_lock_bh(netdev);
-	ether_addr_copy(netdev->dev_addr, saddr->sa_data);
+	eth_hw_addr_set(netdev, saddr->sa_data);
 	netif_addr_unlock_bh(netdev);
 
 	mlx5e_nic_set_rx_mode(priv);
@@ -3270,16 +3268,25 @@
 	}
 
 	new_params = *cur_params;
-	new_params.lro_en = enable;
 
-	if (cur_params->rq_wq_type == MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ) {
-		if (mlx5e_rx_mpwqe_is_linear_skb(mdev, cur_params, NULL) ==
-		    mlx5e_rx_mpwqe_is_linear_skb(mdev, &new_params, NULL))
-			reset = false;
+	if (enable)
+		new_params.packet_merge.type = MLX5E_PACKET_MERGE_LRO;
+	else if (new_params.packet_merge.type == MLX5E_PACKET_MERGE_LRO)
+		new_params.packet_merge.type = MLX5E_PACKET_MERGE_NONE;
+	else
+		goto out;
+
+	if (!(cur_params->packet_merge.type == MLX5E_PACKET_MERGE_SHAMPO &&
+	      new_params.packet_merge.type == MLX5E_PACKET_MERGE_LRO)) {
+		if (cur_params->rq_wq_type == MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ) {
+			if (mlx5e_rx_mpwqe_is_linear_skb(mdev, cur_params, NULL) ==
+			    mlx5e_rx_mpwqe_is_linear_skb(mdev, &new_params, NULL))
+				reset = false;
+		}
 	}
 
 	err = mlx5e_safe_switch_params(priv, &new_params,
-				       mlx5e_modify_tirs_lro_ctx, NULL, reset);
+				       mlx5e_modify_tirs_packet_merge_ctx, NULL, reset);
 out:
 	mutex_unlock(&priv->state_lock);
 	return err;
@@ -3302,7 +3309,9 @@
 	struct mlx5e_priv *priv = netdev_priv(netdev);
 
 #if IS_ENABLED(CONFIG_MLX5_CLS_ACT)
-	if (!enable && mlx5e_tc_num_filters(priv, MLX5_TC_FLAG(NIC_OFFLOAD))) {
+	int tc_flag = mlx5e_is_uplink_rep(priv) ? MLX5_TC_FLAG(ESW_OFFLOAD) :
+						  MLX5_TC_FLAG(NIC_OFFLOAD);
+	if (!enable && mlx5e_tc_num_filters(priv, tc_flag)) {
 		netdev_err(netdev,
 			   "Active offloaded tc filters, can't turn hw_tc_offload off\n");
 		return -EINVAL;
@@ -3350,41 +3359,28 @@
 	return mlx5_set_ports_check(mdev, in, sizeof(in));
 }
 
+static int mlx5e_set_rx_port_ts_wrap(struct mlx5e_priv *priv, void *ctx)
+{
+	struct mlx5_core_dev *mdev = priv->mdev;
+	bool enable = *(bool *)ctx;
+
+	return mlx5e_set_rx_port_ts(mdev, enable);
+}
+
 static int set_feature_rx_fcs(struct net_device *netdev, bool enable)
 {
 	struct mlx5e_priv *priv = netdev_priv(netdev);
 	struct mlx5e_channels *chs = &priv->channels;
-	struct mlx5_core_dev *mdev = priv->mdev;
+	struct mlx5e_params new_params;
 	int err;
+	bool rx_ts_over_crc = !enable;
 
 	mutex_lock(&priv->state_lock);
 
-	if (enable) {
-		err = mlx5e_set_rx_port_ts(mdev, false);
-		if (err)
-			goto out;
-
-		chs->params.scatter_fcs_en = true;
-		err = mlx5e_modify_channels_scatter_fcs(chs, true);
-		if (err) {
-			chs->params.scatter_fcs_en = false;
-			mlx5e_set_rx_port_ts(mdev, true);
-		}
-	} else {
-		chs->params.scatter_fcs_en = false;
-		err = mlx5e_modify_channels_scatter_fcs(chs, false);
-		if (err) {
-			chs->params.scatter_fcs_en = true;
-			goto out;
-		}
-		err = mlx5e_set_rx_port_ts(mdev, true);
-		if (err) {
-			mlx5_core_warn(mdev, "Failed to set RX port timestamp %d\n", err);
-			err = 0;
-		}
-	}
-
-out:
+	new_params = chs->params;
+	new_params.scatter_fcs_en = enable;
+	err = mlx5e_safe_switch_params(priv, &new_params, mlx5e_set_rx_port_ts_wrap,
+				       &rx_ts_over_crc, true);
 	mutex_unlock(&priv->state_lock);
 	return err;
 }
@@ -3427,12 +3423,11 @@
 
 static int mlx5e_handle_feature(struct net_device *netdev,
 				netdev_features_t *features,
-				netdev_features_t wanted_features,
 				netdev_features_t feature,
 				mlx5e_feature_handler feature_handler)
 {
-	netdev_features_t changes = wanted_features ^ netdev->features;
-	bool enable = !!(wanted_features & feature);
+	netdev_features_t changes = *features ^ netdev->features;
+	bool enable = !!(*features & feature);
 	int err;
 
 	if (!(changes & feature))
@@ -3440,22 +3435,22 @@
 
 	err = feature_handler(netdev, enable);
 	if (err) {
+		MLX5E_SET_FEATURE(features, feature, !enable);
 		netdev_err(netdev, "%s feature %pNF failed, err %d\n",
 			   enable ? "Enable" : "Disable", &feature, err);
 		return err;
 	}
 
-	MLX5E_SET_FEATURE(features, feature, enable);
 	return 0;
 }
 
 int mlx5e_set_features(struct net_device *netdev, netdev_features_t features)
 {
-	netdev_features_t oper_features = netdev->features;
+	netdev_features_t oper_features = features;
 	int err = 0;
 
 #define MLX5E_HANDLE_FEATURE(feature, handler) \
-	mlx5e_handle_feature(netdev, &oper_features, features, feature, handler)
+	mlx5e_handle_feature(netdev, &oper_features, feature, handler)
 
 	err |= MLX5E_HANDLE_FEATURE(NETIF_F_LRO, set_feature_lro);
 	err |= MLX5E_HANDLE_FEATURE(NETIF_F_HW_VLAN_CTAG_FILTER,
@@ -3520,14 +3515,25 @@
 		}
 	}
 
+	if (params->xdp_prog) {
+		if (features & NETIF_F_LRO) {
+			netdev_warn(netdev, "LRO is incompatible with XDP\n");
+			features &= ~NETIF_F_LRO;
+		}
+	}
+
 	if (MLX5E_GET_PFLAG(params, MLX5E_PFLAG_RX_CQE_COMPRESS)) {
 		features &= ~NETIF_F_RXHASH;
 		if (netdev->features & NETIF_F_RXHASH)
 			netdev_warn(netdev, "Disabling rxhash, not supported when CQE compress is active\n");
 	}
 
-	if (mlx5e_is_uplink_rep(priv))
+	if (mlx5e_is_uplink_rep(priv)) {
 		features = mlx5e_fix_uplink_rep_features(netdev, features);
+		features |= NETIF_F_NETNS_LOCAL;
+	} else {
+		features &= ~NETIF_F_NETNS_LOCAL;
+	}
 
 	mutex_unlock(&priv->state_lock);
 
@@ -3606,7 +3612,7 @@
 		goto out;
 	}
 
-	if (params->lro_en)
+	if (params->packet_merge.type == MLX5E_PACKET_MERGE_LRO)
 		reset = false;
 
 	if (params->rq_wq_type == MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ) {
@@ -3983,7 +3989,7 @@
 
 		/* Verify if UDP port is being offloaded by HW */
 		if (mlx5_vxlan_lookup_port(priv->mdev->vxlan, port))
-			return features;
+			return vxlan_features_check(skb, features);
 
 #if IS_ENABLED(CONFIG_GENEVE)
 		/* Support Geneve offload for default UDP port */
@@ -4009,7 +4015,6 @@
 	struct mlx5e_priv *priv = netdev_priv(netdev);
 
 	features = vlan_features_check(skb, features);
-	features = vxlan_features_check(skb, features);
 
 	/* Validate if the tunneled packet is being offloaded by HW */
 	if (skb->encapsulation &&
@@ -4063,8 +4068,8 @@
 	struct net_device *netdev = priv->netdev;
 	struct mlx5e_params new_params;
 
-	if (priv->channels.params.lro_en) {
-		netdev_warn(netdev, "can't set XDP while LRO is on, disable LRO first\n");
+	if (priv->channels.params.packet_merge.type != MLX5E_PACKET_MERGE_NONE) {
+		netdev_warn(netdev, "can't set XDP while HW-GRO/LRO is on, disable them first\n");
 		return -EINVAL;
 	}
 
@@ -4152,6 +4157,11 @@
 
 unlock:
 	mutex_unlock(&priv->state_lock);
+
+	/* Need to fix some features. */
+	if (!err)
+		netdev_update_features(netdev);
+
 	return err;
 }
 
@@ -4176,11 +4186,9 @@
 	struct mlx5e_priv *priv = netdev_priv(dev);
 	struct mlx5_core_dev *mdev = priv->mdev;
 	u8 mode, setting;
-	int err;
 
-	err = mlx5_eswitch_get_vepa(mdev->priv.eswitch, &setting);
-	if (err)
-		return err;
+	if (mlx5_eswitch_get_vepa(mdev->priv.eswitch, &setting))
+		return -EOPNOTSUPP;
 	mode = setting ? BRIDGE_MODE_VEPA : BRIDGE_MODE_VEB;
 	return ndo_dflt_bridge_getlink(skb, pid, seq, dev,
 				       mode,
@@ -4316,14 +4324,7 @@
 	/* RQ */
 	mlx5e_build_rq_params(mdev, params);
 
-	/* HW LRO */
-	if (MLX5_CAP_ETH(mdev, lro_cap) &&
-	    params->rq_wq_type == MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ) {
-		/* No XSK params: checking the availability of striding RQ in general. */
-		if (!mlx5e_rx_mpwqe_is_linear_skb(mdev, params, NULL))
-			params->lro_en = !slow_pci_heuristic(mdev);
-	}
-	params->lro_timeout = mlx5e_choose_lro_timeout(mdev, MLX5E_DEFAULT_LRO_TIMEOUT);
+	params->packet_merge.timeout = mlx5e_choose_lro_timeout(mdev, MLX5E_DEFAULT_LRO_TIMEOUT);
 
 	/* CQ moderation params */
 	rx_cq_period_mode = MLX5_CAP_GEN(mdev, cq_period_start_from_cqe) ?
@@ -4462,15 +4463,22 @@
 	}
 
 	if (mlx5_vxlan_allowed(mdev->vxlan) || mlx5_geneve_tx_allowed(mdev)) {
-		netdev->hw_features     |= NETIF_F_GSO_UDP_TUNNEL;
-		netdev->hw_enc_features |= NETIF_F_GSO_UDP_TUNNEL;
-		netdev->vlan_features |= NETIF_F_GSO_UDP_TUNNEL;
+		netdev->hw_features     |= NETIF_F_GSO_UDP_TUNNEL |
+					   NETIF_F_GSO_UDP_TUNNEL_CSUM;
+		netdev->hw_enc_features |= NETIF_F_GSO_UDP_TUNNEL |
+					   NETIF_F_GSO_UDP_TUNNEL_CSUM;
+		netdev->gso_partial_features = NETIF_F_GSO_UDP_TUNNEL_CSUM;
+		netdev->vlan_features |= NETIF_F_GSO_UDP_TUNNEL |
+					 NETIF_F_GSO_UDP_TUNNEL_CSUM;
 	}
 
 	if (mlx5e_tunnel_proto_supported_tx(mdev, IPPROTO_GRE)) {
-		netdev->hw_features     |= NETIF_F_GSO_GRE;
-		netdev->hw_enc_features |= NETIF_F_GSO_GRE;
-		netdev->gso_partial_features |= NETIF_F_GSO_GRE;
+		netdev->hw_features     |= NETIF_F_GSO_GRE |
+					   NETIF_F_GSO_GRE_CSUM;
+		netdev->hw_enc_features |= NETIF_F_GSO_GRE |
+					   NETIF_F_GSO_GRE_CSUM;
+		netdev->gso_partial_features |= NETIF_F_GSO_GRE |
+						NETIF_F_GSO_GRE_CSUM;
 	}
 
 	if (mlx5e_tunnel_proto_supported_tx(mdev, IPPROTO_IPIP)) {
@@ -4608,7 +4616,6 @@
 {
 	struct mlx5_core_dev *mdev = priv->mdev;
 	enum mlx5e_rx_res_features features;
-	struct mlx5e_lro_param lro_param;
 	int err;
 
 	priv->rx_res = mlx5e_rx_res_alloc();
@@ -4626,9 +4633,9 @@
 	features = MLX5E_RX_RES_FEATURE_XSK | MLX5E_RX_RES_FEATURE_PTP;
 	if (priv->channels.params.tunneled_offload_en)
 		features |= MLX5E_RX_RES_FEATURE_INNER_FT;
-	lro_param = mlx5e_get_lro_param(&priv->channels.params);
 	err = mlx5e_rx_res_init(priv->rx_res, priv->mdev, features,
-				priv->max_nch, priv->drop_rq.rqn, &lro_param,
+				priv->max_nch, priv->drop_rq.rqn,
+				&priv->channels.params.packet_merge,
 				priv->channels.params.num_channels);
 	if (err)
 		goto err_close_drop_rq;
@@ -4885,6 +4892,7 @@
 	}
 
 	netif_carrier_off(netdev);
+	netif_tx_disable(netdev);
 	dev_net_set(netdev, mlx5_core_net(mdev));
 
 	return netdev;
@@ -4998,8 +5006,8 @@
 }
 
 static int
-mlx5e_netdev_attach_profile(struct net_device *netdev, struct mlx5_core_dev *mdev,
-			    const struct mlx5e_profile *new_profile, void *new_ppriv)
+mlx5e_netdev_init_profile(struct net_device *netdev, struct mlx5_core_dev *mdev,
+			  const struct mlx5e_profile *new_profile, void *new_ppriv)
 {
 	struct mlx5e_priv *priv = netdev_priv(netdev);
 	int err;
@@ -5015,6 +5023,25 @@
 	err = new_profile->init(priv->mdev, priv->netdev);
 	if (err)
 		goto priv_cleanup;
+
+	return 0;
+
+priv_cleanup:
+	mlx5e_priv_cleanup(priv);
+	return err;
+}
+
+static int
+mlx5e_netdev_attach_profile(struct net_device *netdev, struct mlx5_core_dev *mdev,
+			    const struct mlx5e_profile *new_profile, void *new_ppriv)
+{
+	struct mlx5e_priv *priv = netdev_priv(netdev);
+	int err;
+
+	err = mlx5e_netdev_init_profile(netdev, mdev, new_profile, new_ppriv);
+	if (err)
+		return err;
+
 	err = mlx5e_attach_netdev(priv);
 	if (err)
 		goto profile_cleanup;
@@ -5022,7 +5049,6 @@
 
 profile_cleanup:
 	new_profile->cleanup(priv);
-priv_cleanup:
 	mlx5e_priv_cleanup(priv);
 	return err;
 }
@@ -5041,6 +5067,12 @@
 	priv->profile->cleanup(priv);
 	mlx5e_priv_cleanup(priv);
 
+	if (mdev->state == MLX5_DEVICE_STATE_INTERNAL_ERROR) {
+		mlx5e_netdev_init_profile(netdev, mdev, new_profile, new_ppriv);
+		set_bit(MLX5E_STATE_DESTROYING, &priv->state);
+		return -EIO;
+	}
+
 	err = mlx5e_netdev_attach_profile(netdev, mdev, new_profile, new_ppriv);
 	if (err) { /* roll back to original profile */
 		netdev_warn(netdev, "%s: new profile init failed, %d\n", __func__, err);
@@ -5100,8 +5132,11 @@
 	struct net_device *netdev = priv->netdev;
 	struct mlx5_core_dev *mdev = priv->mdev;
 
-	if (!netif_device_present(netdev))
+	if (!netif_device_present(netdev)) {
+		if (test_bit(MLX5E_STATE_DESTROYING, &priv->state))
+			mlx5e_destroy_mdev_resources(mdev);
 		return -ENODEV;
+	}
 
 	mlx5e_detach_netdev(priv);
 	mlx5e_destroy_mdev_resources(mdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
@@ -50,9 +50,11 @@
 #include "fs_core.h"
 #include "lib/mlx5.h"
 #include "lib/devcom.h"
+#include "lib/vxlan.h"
 #define CREATE_TRACE_POINTS
 #include "diag/en_rep_tracepoint.h"
 #include "en_accel/ipsec.h"
+#include "en/tc/int_port.h"
 
 #define MLX5E_REP_PARAMS_DEF_LOG_SQ_SIZE \
 	max(0x7, MLX5E_PARAMS_MINIMUM_LOG_SQ_SIZE)
@@ -65,13 +67,17 @@
 {
 	struct mlx5e_priv *priv = netdev_priv(dev);
 	struct mlx5_core_dev *mdev = priv->mdev;
+	int count;
 
 	strlcpy(drvinfo->driver, mlx5e_rep_driver_name,
 		sizeof(drvinfo->driver));
-	snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
-		 "%d.%d.%04d (%.16s)",
-		 fw_rev_maj(mdev), fw_rev_min(mdev),
-		 fw_rev_sub(mdev), mdev->board_id);
+	count = snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
+			 "%d.%d.%04d (%.16s)", fw_rev_maj(mdev),
+			 fw_rev_min(mdev), fw_rev_sub(mdev), mdev->board_id);
+	if (count >= sizeof(drvinfo->fw_version))
+		snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
+			 "%d.%d.%04d", fw_rev_maj(mdev),
+			 fw_rev_min(mdev), fw_rev_sub(mdev));
 }
 
 static const struct counter_desc sw_rep_stats_desc[] = {
@@ -617,6 +623,8 @@
 
 	params->mqprio.num_tc       = 1;
 	params->tunneled_offload_en = false;
+	if (rep->vport != MLX5_VPORT_UPLINK)
+		params->vlan_strip_disable = true;
 
 	/* Set an initial non-zero value, so that mlx5e_select_queue won't
 	 * divide by zero if called before first activating channels.
@@ -793,7 +801,6 @@
 static int mlx5e_init_rep_rx(struct mlx5e_priv *priv)
 {
 	struct mlx5_core_dev *mdev = priv->mdev;
-	struct mlx5e_lro_param lro_param;
 	int err;
 
 	priv->rx_res = mlx5e_rx_res_alloc();
@@ -808,9 +815,9 @@
 		return err;
 	}
 
-	lro_param = mlx5e_get_lro_param(&priv->channels.params);
 	err = mlx5e_rx_res_init(priv->rx_res, priv->mdev, 0,
-				priv->max_nch, priv->drop_rq.rqn, &lro_param,
+				priv->max_nch, priv->drop_rq.rqn,
+				&priv->channels.params.packet_merge,
 				priv->channels.params.num_channels);
 	if (err)
 		goto err_close_drop_rq;
@@ -858,12 +865,22 @@
 
 static int mlx5e_init_ul_rep_rx(struct mlx5e_priv *priv)
 {
+	int err;
+
 	mlx5e_create_q_counters(priv);
-	return mlx5e_init_rep_rx(priv);
+	err = mlx5e_init_rep_rx(priv);
+	if (err)
+		goto out;
+
+	mlx5e_tc_int_port_init_rep_rx(priv);
+
+out:
+	return err;
 }
 
 static void mlx5e_cleanup_ul_rep_rx(struct mlx5e_priv *priv)
 {
+	mlx5e_tc_int_port_cleanup_rep_rx(priv);
 	mlx5e_cleanup_rep_rx(priv);
 	mlx5e_destroy_q_counters(priv);
 }
@@ -1017,6 +1034,7 @@
 	rtnl_lock();
 	if (netif_running(netdev))
 		mlx5e_open(netdev);
+	udp_tunnel_nic_reset_ntf(priv->netdev);
 	netif_device_attach(netdev);
 	rtnl_unlock();
 }
@@ -1038,6 +1056,7 @@
 	mlx5_notifier_unregister(mdev, &priv->events_nb);
 	mlx5e_rep_tc_disable(priv);
 	mlx5_lag_remove_netdev(mdev, priv->netdev);
+	mlx5_vxlan_reset_to_default(mdev->vxlan);
 }
 
 static MLX5E_DEFINE_STATS_GRP(sw_rep, 0);
@@ -1070,6 +1089,10 @@
 	&MLX5E_STATS_GRP(pme),
 	&MLX5E_STATS_GRP(channels),
 	&MLX5E_STATS_GRP(per_port_buff_congest),
+#ifdef CONFIG_MLX5_EN_IPSEC
+	&MLX5E_STATS_GRP(ipsec_sw),
+	&MLX5E_STATS_GRP(ipsec_hw),
+#endif
 };
 
 static unsigned int mlx5e_ul_rep_stats_grps_num(struct mlx5e_priv *priv)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_rep.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_rep.h
@@ -58,6 +58,7 @@
 };
 
 struct mlx5_tc_ct_priv;
+struct mlx5_tc_int_port_priv;
 struct mlx5e_rep_bond;
 struct mlx5e_tc_tun_encap;
 struct mlx5e_post_act;
@@ -98,6 +99,9 @@
 
 	/* tc tunneling encapsulation private data */
 	struct mlx5e_tc_tun_encap *encap;
+
+	/* OVS internal port support */
+	struct mlx5e_tc_int_port_priv *int_port_priv;
 };
 
 struct mlx5e_rep_priv {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_rx.c
@@ -271,8 +271,8 @@
 	if (unlikely(!dma_info->page))
 		return -ENOMEM;
 
-	dma_info->addr = dma_map_page(rq->pdev, dma_info->page, 0,
-				      PAGE_SIZE, rq->buff.map_dir);
+	dma_info->addr = dma_map_page_attrs(rq->pdev, dma_info->page, 0, PAGE_SIZE,
+					    rq->buff.map_dir, DMA_ATTR_SKIP_CPU_SYNC);
 	if (unlikely(dma_mapping_error(rq->pdev, dma_info->addr))) {
 		page_pool_recycle_direct(rq->page_pool, dma_info->page);
 		dma_info->page = NULL;
@@ -293,7 +293,8 @@
 
 void mlx5e_page_dma_unmap(struct mlx5e_rq *rq, struct mlx5e_dma_info *dma_info)
 {
-	dma_unmap_page(rq->pdev, dma_info->addr, PAGE_SIZE, rq->buff.map_dir);
+	dma_unmap_page_attrs(rq->pdev, dma_info->addr, PAGE_SIZE, rq->buff.map_dir,
+			     DMA_ATTR_SKIP_CPU_SYNC);
 }
 
 void mlx5e_page_release_dynamic(struct mlx5e_rq *rq,
@@ -986,7 +987,8 @@
 	}
 
 	/* True when explicitly set via priv flag, or XDP prog is loaded */
-	if (test_bit(MLX5E_RQ_STATE_NO_CSUM_COMPLETE, &rq->state))
+	if (test_bit(MLX5E_RQ_STATE_NO_CSUM_COMPLETE, &rq->state) ||
+	    get_cqe_tls_offload(cqe))
 		goto csum_unnecessary;
 
 	/* CQE csum doesn't cover padding octets in short ethernet
@@ -1275,7 +1277,6 @@
 	struct mlx5e_priv *priv = netdev_priv(netdev);
 	struct mlx5e_rep_priv *rpriv  = priv->ppriv;
 	struct mlx5_eswitch_rep *rep = rpriv->rep;
-	struct mlx5e_tc_update_priv tc_priv = {};
 	struct mlx5_wq_cyc *wq = &rq->wqe.wq;
 	struct mlx5e_wqe_frag_info *wi;
 	struct sk_buff *skb;
@@ -1311,15 +1312,7 @@
 	if (rep->vlan && skb_vlan_tag_present(skb))
 		skb_vlan_pop(skb);
 
-	if (unlikely(!mlx5_ipsec_is_rx_flow(cqe) &&
-		     !mlx5e_rep_tc_update_skb(cqe, skb, &tc_priv))) {
-		dev_kfree_skb_any(skb);
-		goto free_wqe;
-	}
-
-	napi_gro_receive(rq->cq.napi, skb);
-
-	mlx5_rep_tc_post_napi_receive(&tc_priv);
+	mlx5e_rep_tc_receive(cqe, rq, skb);
 
 free_wqe:
 	mlx5e_free_rx_wqe(rq, wi, true);
@@ -1336,7 +1329,6 @@
 	u32 wqe_offset     = stride_ix << rq->mpwqe.log_stride_sz;
 	u32 head_offset    = wqe_offset & (PAGE_SIZE - 1);
 	u32 page_idx       = wqe_offset >> PAGE_SHIFT;
-	struct mlx5e_tc_update_priv tc_priv = {};
 	struct mlx5e_rx_wqe_ll *wqe;
 	struct mlx5_wq_ll *wq;
 	struct sk_buff *skb;
@@ -1369,15 +1361,7 @@
 
 	mlx5e_complete_rx_cqe(rq, cqe, cqe_bcnt, skb);
 
-	if (unlikely(!mlx5_ipsec_is_rx_flow(cqe) &&
-		     !mlx5e_rep_tc_update_skb(cqe, skb, &tc_priv))) {
-		dev_kfree_skb_any(skb);
-		goto mpwrq_cqe_out;
-	}
-
-	napi_gro_receive(rq->cq.napi, skb);
-
-	mlx5_rep_tc_post_napi_receive(&tc_priv);
+	mlx5e_rep_tc_receive(cqe, rq, skb);
 
 mpwrq_cqe_out:
 	if (likely(wi->consumed_strides < rq->mpwqe.num_strides))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_stats.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_stats.c
@@ -614,7 +614,7 @@
 	u32 in[MLX5_ST_SZ_DW(query_vnic_env_in)] = {};
 	struct mlx5_core_dev *mdev = priv->mdev;
 
-	if (!MLX5_CAP_GEN(priv->mdev, nic_receive_steering_discard))
+	if (!mlx5e_stats_grp_vnic_env_num_stats(priv))
 		return;
 
 	MLX5_SET(query_vnic_env_in, in, opcode, MLX5_CMD_OP_QUERY_VNIC_ENV);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
@@ -59,7 +59,6 @@
 #include "en/mapping.h"
 #include "en/tc_ct.h"
 #include "en/mod_hdr.h"
-#include "en/tc_priv.h"
 #include "en/tc_tun_encap.h"
 #include "en/tc/sample.h"
 #include "lib/devcom.h"
@@ -71,7 +70,6 @@
 #include "lag_mp.h"
 
 #define nic_chains(priv) ((priv)->fs.tc.chains)
-#define MLX5_MH_ACT_SZ MLX5_UN_SZ_BYTES(set_add_copy_action_in_auto)
 
 #define MLX5E_TC_TABLE_NUM_GROUPS 4
 #define MLX5E_TC_TABLE_MAX_GROUP_SIZE BIT(18)
@@ -209,12 +207,9 @@
 	char *modact;
 	int err;
 
-	err = alloc_mod_hdr_actions(mdev, ns, mod_hdr_acts);
-	if (err)
-		return err;
-
-	modact = mod_hdr_acts->actions +
-		 (mod_hdr_acts->num_actions * MLX5_MH_ACT_SZ);
+	modact = mlx5e_mod_hdr_alloc(mdev, ns, mod_hdr_acts);
+	if (IS_ERR(modact))
+		return PTR_ERR(modact);
 
 	/* Firmware has 5bit length field and 0 means 32bits */
 	if (mlen == 32)
@@ -231,6 +226,23 @@
 	return err;
 }
 
+struct mlx5e_tc_int_port_priv *
+mlx5e_get_int_port_priv(struct mlx5e_priv *priv)
+{
+	struct mlx5_eswitch *esw = priv->mdev->priv.eswitch;
+	struct mlx5_rep_uplink_priv *uplink_priv;
+	struct mlx5e_rep_priv *uplink_rpriv;
+
+	if (is_mdev_switchdev_mode(priv->mdev)) {
+		uplink_rpriv = mlx5_eswitch_get_uplink_priv(esw, REP_ETH);
+		uplink_priv = &uplink_rpriv->uplink_priv;
+
+		return uplink_priv->int_port_priv;
+	}
+
+	return NULL;
+}
+
 static struct mlx5_tc_ct_priv *
 get_ct_priv(struct mlx5e_priv *priv)
 {
@@ -248,7 +260,6 @@
 	return priv->fs.tc.ct;
 }
 
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
 static struct mlx5e_tc_psample *
 get_sample_priv(struct mlx5e_priv *priv)
 {
@@ -265,7 +276,6 @@
 
 	return NULL;
 }
-#endif
 
 struct mlx5_flow_handle *
 mlx5_tc_rule_insert(struct mlx5e_priv *priv,
@@ -318,7 +328,7 @@
 	int mlen = mlx5e_tc_attr_to_reg_mappings[type].mlen;
 	char *modact;
 
-	modact = mod_hdr_acts->actions + (act_id * MLX5_MH_ACT_SZ);
+	modact = mlx5e_mod_hdr_get_item(mod_hdr_acts, act_id);
 
 	/* Firmware has 5bit length field and 0 means 32bits */
 	if (mlen == 32)
@@ -1061,7 +1071,7 @@
 
 	if (attr->action & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR) {
 		err = mlx5e_attach_mod_hdr(priv, flow, parse_attr);
-		dealloc_mod_hdr_actions(&parse_attr->mod_hdr_acts);
+		mlx5e_mod_hdr_dealloc(&parse_attr->mod_hdr_acts);
 		if (err)
 			return err;
 	}
@@ -1148,11 +1158,9 @@
 		rule = mlx5_tc_ct_flow_offload(get_ct_priv(flow->priv),
 					       flow, spec, attr,
 					       mod_hdr_acts);
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
 	} else if (flow_flag_test(flow, SAMPLE)) {
 		rule = mlx5e_tc_sample_offload(get_sample_priv(flow->priv), spec, attr,
 					       mlx5e_tc_get_flow_tun_id(flow));
-#endif
 	} else {
 		rule = mlx5_eswitch_add_offloaded_rule(esw, spec, attr);
 	}
@@ -1183,23 +1191,16 @@
 	if (attr->flags & MLX5_ESW_ATTR_FLAG_SLOW_PATH)
 		goto offload_rule_0;
 
-	if (flow_flag_test(flow, CT)) {
-		mlx5_tc_ct_delete_flow(get_ct_priv(flow->priv), flow, attr);
-		return;
-	}
-
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
-	if (flow_flag_test(flow, SAMPLE)) {
-		mlx5e_tc_sample_unoffload(get_sample_priv(flow->priv), flow->rule[0], attr);
-		return;
-	}
-#endif
-
 	if (attr->esw_attr->split_count)
 		mlx5_eswitch_del_fwd_rule(esw, flow->rule[1], attr);
 
+	if (flow_flag_test(flow, CT))
+		mlx5_tc_ct_delete_flow(get_ct_priv(flow->priv), flow, attr);
+	else if (flow_flag_test(flow, SAMPLE))
+		mlx5e_tc_sample_unoffload(get_sample_priv(flow->priv), flow->rule[0], attr);
+	else
 offload_rule_0:
-	mlx5_eswitch_del_offloaded_rule(esw, flow->rule[0], attr);
+		mlx5_eswitch_del_offloaded_rule(esw, flow->rule[0], attr);
 }
 
 struct mlx5_flow_handle *
@@ -1293,7 +1294,8 @@
 	uplink_priv = &rpriv->uplink_priv;
 
 	mutex_lock(&uplink_priv->unready_flows_lock);
-	unready_flow_del(flow);
+	if (flow_flag_test(flow, NOT_READY))
+		unready_flow_del(flow);
 	mutex_unlock(&uplink_priv->unready_flows_lock);
 }
 
@@ -1319,11 +1321,9 @@
 int mlx5e_tc_query_route_vport(struct net_device *out_dev, struct net_device *route_dev, u16 *vport)
 {
 	struct mlx5e_priv *out_priv, *route_priv;
-	struct mlx5_devcom *devcom = NULL;
 	struct mlx5_core_dev *route_mdev;
 	struct mlx5_eswitch *esw;
 	u16 vhca_id;
-	int err;
 
 	out_priv = netdev_priv(out_dev);
 	esw = out_priv->mdev->priv.eswitch;
@@ -1332,6 +1332,9 @@
 
 	vhca_id = MLX5_CAP_GEN(route_mdev, vhca_id);
 	if (mlx5_lag_is_active(out_priv->mdev)) {
+		struct mlx5_devcom *devcom;
+		int err;
+
 		/* In lag case we may get devices from different eswitch instances.
 		 * If we failed to get vport num, it means, mostly, that we on the wrong
 		 * eswitch.
@@ -1340,23 +1343,23 @@
 		if (err != -ENOENT)
 			return err;
 
+		rcu_read_lock();
 		devcom = out_priv->mdev->priv.devcom;
-		esw = mlx5_devcom_get_peer_data(devcom, MLX5_DEVCOM_ESW_OFFLOADS);
-		if (!esw)
-			return -ENODEV;
+		esw = mlx5_devcom_get_peer_data_rcu(devcom, MLX5_DEVCOM_ESW_OFFLOADS);
+		err = esw ? mlx5_eswitch_vhca_id_to_vport(esw, vhca_id, vport) : -ENODEV;
+		rcu_read_unlock();
+
+		return err;
 	}
 
-	err = mlx5_eswitch_vhca_id_to_vport(esw, vhca_id, vport);
-	if (devcom)
-		mlx5_devcom_release_peer_data(devcom, MLX5_DEVCOM_ESW_OFFLOADS);
-	return err;
+	return mlx5_eswitch_vhca_id_to_vport(esw, vhca_id, vport);
 }
 
 int mlx5e_tc_add_flow_mod_hdr(struct mlx5e_priv *priv,
-			      struct mlx5e_tc_flow_parse_attr *parse_attr,
-			      struct mlx5e_tc_flow *flow)
+			      struct mlx5e_tc_flow *flow,
+			      struct mlx5_flow_attr *attr)
 {
-	struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts = &parse_attr->mod_hdr_acts;
+	struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts = &attr->parse_attr->mod_hdr_acts;
 	struct mlx5_modify_hdr *mod_hdr;
 
 	mod_hdr = mlx5_modify_header_alloc(priv->mdev,
@@ -1366,8 +1369,8 @@
 	if (IS_ERR(mod_hdr))
 		return PTR_ERR(mod_hdr);
 
-	WARN_ON(flow->attr->modify_hdr);
-	flow->attr->modify_hdr = mod_hdr;
+	WARN_ON(attr->modify_hdr);
+	attr->modify_hdr = mod_hdr;
 
 	return 0;
 }
@@ -1390,6 +1393,9 @@
 	int err = 0;
 	int out_index;
 
+	parse_attr = attr->parse_attr;
+	esw_attr = attr->esw_attr;
+
 	/* We check chain range only for tc flows.
 	 * For ft flows, we checked attr->chain was originally 0 and set it to
 	 * FDB_FT_CHAIN which is outside tc range.
@@ -1415,6 +1421,27 @@
 		err = mlx5e_attach_decap_route(priv, flow);
 		if (err)
 			goto err_out;
+
+		if (!attr->chain && esw_attr->int_port &&
+		    attr->action & MLX5_FLOW_CONTEXT_ACTION_FWD_DEST) {
+			/* If decap route device is internal port, change the
+			 * source vport value in reg_c0 back to uplink just in
+			 * case the rule performs goto chain > 0. If we have a miss
+			 * on chain > 0 we want the metadata regs to hold the
+			 * chain id so SW will resume handling of this packet
+			 * from the proper chain.
+			 */
+			u32 metadata = mlx5_eswitch_get_vport_metadata_for_set(esw,
+									esw_attr->in_rep->vport);
+
+			err = mlx5e_tc_match_to_reg_set(priv->mdev, &parse_attr->mod_hdr_acts,
+							MLX5_FLOW_NAMESPACE_FDB, VPORT_TO_REG,
+							metadata);
+			if (err)
+				goto err_out;
+
+			attr->action |= MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
+		}
 	}
 
 	if (flow_flag_test(flow, L3_TO_L2_DECAP)) {
@@ -1423,8 +1450,35 @@
 			goto err_out;
 	}
 
-	parse_attr = attr->parse_attr;
-	esw_attr = attr->esw_attr;
+	if (netif_is_ovs_master(parse_attr->filter_dev)) {
+		struct mlx5e_tc_int_port *int_port;
+
+		if (attr->chain) {
+			NL_SET_ERR_MSG_MOD(extack,
+					   "Internal port rule is only supported on chain 0");
+			err = -EOPNOTSUPP;
+			goto err_out;
+		}
+
+		if (attr->dest_chain) {
+			NL_SET_ERR_MSG_MOD(extack,
+					   "Internal port rule offload doesn't support goto action");
+			err = -EOPNOTSUPP;
+			goto err_out;
+		}
+
+		int_port = mlx5e_tc_int_port_get(mlx5e_get_int_port_priv(priv),
+						 parse_attr->filter_dev->ifindex,
+						 flow_flag_test(flow, EGRESS) ?
+						 MLX5E_TC_INT_PORT_EGRESS :
+						 MLX5E_TC_INT_PORT_INGRESS);
+		if (IS_ERR(int_port)) {
+			err = PTR_ERR(int_port);
+			goto err_out;
+		}
+
+		esw_attr->int_port = int_port;
+	}
 
 	for (out_index = 0; out_index < MLX5_MAX_FLOW_FWD_VPORTS; out_index++) {
 		struct net_device *out_dev;
@@ -1447,7 +1501,8 @@
 			goto err_out;
 
 		if (esw_attr->dests[out_index].flags &
-		    MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE)
+		    MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE &&
+		    !esw_attr->dest_int_port)
 			vf_tun = true;
 		out_priv = netdev_priv(encap_dev);
 		rpriv = out_priv->ppriv;
@@ -1468,7 +1523,7 @@
 	if (attr->action & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR &&
 	    !(attr->ct_attr.ct_action & TCA_CT_ACT_CLEAR)) {
 		if (vf_tun) {
-			err = mlx5e_tc_add_flow_mod_hdr(priv, parse_attr, flow);
+			err = mlx5e_tc_add_flow_mod_hdr(priv, flow, attr);
 			if (err)
 				goto err_out;
 		} else {
@@ -1535,8 +1590,7 @@
 	esw_attr = attr->esw_attr;
 	mlx5e_put_flow_tunnel_id(flow);
 
-	if (flow_flag_test(flow, NOT_READY))
-		remove_unready_flow(flow);
+	remove_unready_flow(flow);
 
 	if (mlx5e_is_offloaded_flow(flow)) {
 		if (flow_flag_test(flow, SLOW))
@@ -1544,6 +1598,7 @@
 		else
 			mlx5e_tc_unoffload_fdb_rules(esw, flow, attr);
 	}
+	complete_all(&flow->del_hw_done);
 
 	if (mlx5_flow_has_geneve_opt(flow))
 		mlx5_geneve_tlv_option_del(priv->mdev->geneve);
@@ -1555,7 +1610,8 @@
 
 	for (out_index = 0; out_index < MLX5_MAX_FLOW_FWD_VPORTS; out_index++) {
 		if (esw_attr->dests[out_index].flags &
-		    MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE)
+		    MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE &&
+		    !esw_attr->dest_int_port)
 			vf_tun = true;
 		if (esw_attr->dests[out_index].flags & MLX5_ESW_DEST_ENCAP) {
 			mlx5e_detach_encap(priv, flow, out_index);
@@ -1566,7 +1622,7 @@
 	mlx5_tc_ct_match_del(get_ct_priv(priv), &flow->attr->ct_attr);
 
 	if (attr->action & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR) {
-		dealloc_mod_hdr_actions(&attr->parse_attr->mod_hdr_acts);
+		mlx5e_mod_hdr_dealloc(&attr->parse_attr->mod_hdr_acts);
 		if (vf_tun && attr->modify_hdr)
 			mlx5_modify_header_dealloc(priv->mdev, attr->modify_hdr);
 		else
@@ -1579,6 +1635,12 @@
 	if (attr->action & MLX5_FLOW_CONTEXT_ACTION_COUNT)
 		mlx5_fc_destroy(esw_attr->counter_dev, attr->counter);
 
+	if (esw_attr->int_port)
+		mlx5e_tc_int_port_put(mlx5e_get_int_port_priv(priv), esw_attr->int_port);
+
+	if (esw_attr->dest_int_port)
+		mlx5e_tc_int_port_put(mlx5e_get_int_port_priv(priv), esw_attr->dest_int_port);
+
 	if (flow_flag_test(flow, L3_TO_L2_DECAP))
 		mlx5e_detach_decap(priv, flow);
 
@@ -1884,6 +1946,111 @@
 	return ip_version;
 }
 
+/* Tunnel device follows RFC 6040, see include/net/inet_ecn.h.
+ * And changes inner ip_ecn depending on inner and outer ip_ecn as follows:
+ *      +---------+----------------------------------------+
+ *      |Arriving |         Arriving Outer Header          |
+ *      |   Inner +---------+---------+---------+----------+
+ *      |  Header | Not-ECT | ECT(0)  | ECT(1)  |   CE     |
+ *      +---------+---------+---------+---------+----------+
+ *      | Not-ECT | Not-ECT | Not-ECT | Not-ECT | <drop>   |
+ *      |  ECT(0) |  ECT(0) | ECT(0)  | ECT(1)  |   CE*    |
+ *      |  ECT(1) |  ECT(1) | ECT(1)  | ECT(1)* |   CE*    |
+ *      |    CE   |   CE    |  CE     | CE      |   CE     |
+ *      +---------+---------+---------+---------+----------+
+ *
+ * Tc matches on inner after decapsulation on tunnel device, but hw offload matches
+ * the inner ip_ecn value before hardware decap action.
+ *
+ * Cells marked are changed from original inner packet ip_ecn value during decap, and
+ * so matching those values on inner ip_ecn before decap will fail.
+ *
+ * The following helper allows offload when inner ip_ecn won't be changed by outer ip_ecn,
+ * except for the outer ip_ecn = CE, where in all cases inner ip_ecn will be changed to CE,
+ * and such we can drop the inner ip_ecn=CE match.
+ */
+
+static int mlx5e_tc_verify_tunnel_ecn(struct mlx5e_priv *priv,
+				      struct flow_cls_offload *f,
+				      bool *match_inner_ecn)
+{
+	u8 outer_ecn_mask = 0, outer_ecn_key = 0, inner_ecn_mask = 0, inner_ecn_key = 0;
+	struct flow_rule *rule = flow_cls_offload_flow_rule(f);
+	struct netlink_ext_ack *extack = f->common.extack;
+	struct flow_match_ip match;
+
+	*match_inner_ecn = true;
+
+	if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_ENC_IP)) {
+		flow_rule_match_enc_ip(rule, &match);
+		outer_ecn_key = match.key->tos & INET_ECN_MASK;
+		outer_ecn_mask = match.mask->tos & INET_ECN_MASK;
+	}
+
+	if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_IP)) {
+		flow_rule_match_ip(rule, &match);
+		inner_ecn_key = match.key->tos & INET_ECN_MASK;
+		inner_ecn_mask = match.mask->tos & INET_ECN_MASK;
+	}
+
+	if (outer_ecn_mask != 0 && outer_ecn_mask != INET_ECN_MASK) {
+		NL_SET_ERR_MSG_MOD(extack, "Partial match on enc_tos ecn bits isn't supported");
+		netdev_warn(priv->netdev, "Partial match on enc_tos ecn bits isn't supported");
+		return -EOPNOTSUPP;
+	}
+
+	if (!outer_ecn_mask) {
+		if (!inner_ecn_mask)
+			return 0;
+
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Matching on tos ecn bits without also matching enc_tos ecn bits isn't supported");
+		netdev_warn(priv->netdev,
+			    "Matching on tos ecn bits without also matching enc_tos ecn bits isn't supported");
+		return -EOPNOTSUPP;
+	}
+
+	if (inner_ecn_mask && inner_ecn_mask != INET_ECN_MASK) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Partial match on tos ecn bits with match on enc_tos ecn bits isn't supported");
+		netdev_warn(priv->netdev,
+			    "Partial match on tos ecn bits with match on enc_tos ecn bits isn't supported");
+		return -EOPNOTSUPP;
+	}
+
+	if (!inner_ecn_mask)
+		return 0;
+
+	/* Both inner and outer have full mask on ecn */
+
+	if (outer_ecn_key == INET_ECN_ECT_1) {
+		/* inner ecn might change by DECAP action */
+
+		NL_SET_ERR_MSG_MOD(extack, "Match on enc_tos ecn = ECT(1) isn't supported");
+		netdev_warn(priv->netdev, "Match on enc_tos ecn = ECT(1) isn't supported");
+		return -EOPNOTSUPP;
+	}
+
+	if (outer_ecn_key != INET_ECN_CE)
+		return 0;
+
+	if (inner_ecn_key != INET_ECN_CE) {
+		/* Can't happen in software, as packet ecn will be changed to CE after decap */
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Match on tos enc_tos ecn = CE while match on tos ecn != CE isn't supported");
+		netdev_warn(priv->netdev,
+			    "Match on tos enc_tos ecn = CE while match on tos ecn != CE isn't supported");
+		return -EOPNOTSUPP;
+	}
+
+	/* outer ecn = CE, inner ecn = CE, as decap will change inner ecn to CE in anycase,
+	 * drop match on inner ecn
+	 */
+	*match_inner_ecn = false;
+
+	return 0;
+}
+
 static int parse_tunnel_attr(struct mlx5e_priv *priv,
 			     struct mlx5e_tc_flow *flow,
 			     struct mlx5_flow_spec *spec,
@@ -2077,6 +2244,7 @@
 	struct flow_rule *rule = flow_cls_offload_flow_rule(f);
 	struct flow_dissector *dissector = rule->match.dissector;
 	enum fs_flow_table_type fs_type;
+	bool match_inner_ecn = true;
 	u16 addr_type = 0;
 	u8 ip_proto = 0;
 	u8 *match_level;
@@ -2130,6 +2298,10 @@
 			headers_c = get_match_inner_headers_criteria(spec);
 			headers_v = get_match_inner_headers_value(spec);
 		}
+
+		err = mlx5e_tc_verify_tunnel_ecn(priv, f, &match_inner_ecn);
+		if (err)
+			return err;
 	}
 
 	err = mlx5e_flower_parse_meta(filter_dev, f);
@@ -2191,6 +2363,17 @@
 				 match.key->vlan_priority);
 
 			*match_level = MLX5_MATCH_L2;
+
+			if (!flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_CVLAN) &&
+			    match.mask->vlan_eth_type &&
+			    MLX5_CAP_FLOWTABLE_TYPE(priv->mdev,
+						    ft_field_support.outer_second_vid,
+						    fs_type)) {
+				MLX5_SET(fte_match_set_misc, misc_c,
+					 outer_second_cvlan_tag, 1);
+				spec->match_criteria_enable |=
+					MLX5_MATCH_MISC_PARAMETERS;
+			}
 		}
 	} else if (*match_level != MLX5_MATCH_NONE) {
 		/* cvlan_tag enabled in match criteria and
@@ -2351,10 +2534,12 @@
 		struct flow_match_ip match;
 
 		flow_rule_match_ip(rule, &match);
-		MLX5_SET(fte_match_set_lyr_2_4, headers_c, ip_ecn,
-			 match.mask->tos & 0x3);
-		MLX5_SET(fte_match_set_lyr_2_4, headers_v, ip_ecn,
-			 match.key->tos & 0x3);
+		if (match_inner_ecn) {
+			MLX5_SET(fte_match_set_lyr_2_4, headers_c, ip_ecn,
+				 match.mask->tos & 0x3);
+			MLX5_SET(fte_match_set_lyr_2_4, headers_v, ip_ecn,
+				 match.key->tos & 0x3);
+		}
 
 		MLX5_SET(fte_match_set_lyr_2_4, headers_c, ip_dscp,
 			 match.mask->tos >> 2);
@@ -2654,7 +2839,7 @@
 	OFFLOAD(DIPV6_31_0,   32, U32_MAX, ip6.daddr.s6_addr32[3], 0,
 		dst_ipv4_dst_ipv6.ipv6_layout.ipv6[12]),
 	OFFLOAD(IPV6_HOPLIMIT, 8,  U8_MAX, ip6.hop_limit, 0, ttl_hoplimit),
-	OFFLOAD(IP_DSCP, 16,  0xc00f, ip6, 0, ip_dscp),
+	OFFLOAD(IP_DSCP, 16,  0x0fc0, ip6, 0, ip_dscp),
 
 	OFFLOAD(TCP_SPORT, 16, U16_MAX, tcp.source,  0, tcp_sport),
 	OFFLOAD(TCP_DPORT, 16, U16_MAX, tcp.dest,    0, tcp_dport),
@@ -2665,21 +2850,31 @@
 	OFFLOAD(UDP_DPORT, 16, U16_MAX, udp.dest,   0, udp_dport),
 };
 
-static unsigned long mask_to_le(unsigned long mask, int size)
+static u32 mask_field_get(void *mask, struct mlx5_fields *f)
 {
-	__be32 mask_be32;
-	__be16 mask_be16;
-
-	if (size == 32) {
-		mask_be32 = (__force __be32)(mask);
-		mask = (__force unsigned long)cpu_to_le32(be32_to_cpu(mask_be32));
-	} else if (size == 16) {
-		mask_be32 = (__force __be32)(mask);
-		mask_be16 = *(__be16 *)&mask_be32;
-		mask = (__force unsigned long)cpu_to_le16(be16_to_cpu(mask_be16));
+	switch (f->field_bsize) {
+	case 32:
+		return be32_to_cpu(*(__be32 *)mask) & f->field_mask;
+	case 16:
+		return be16_to_cpu(*(__be16 *)mask) & (u16)f->field_mask;
+	default:
+		return *(u8 *)mask & (u8)f->field_mask;
 	}
+}
 
-	return mask;
+static void mask_field_clear(void *mask, struct mlx5_fields *f)
+{
+	switch (f->field_bsize) {
+	case 32:
+		*(__be32 *)mask &= ~cpu_to_be32(f->field_mask);
+		break;
+	case 16:
+		*(__be16 *)mask &= ~cpu_to_be16((u16)f->field_mask);
+		break;
+	default:
+		*(u8 *)mask &= ~(u8)f->field_mask;
+		break;
+	}
 }
 static int offload_pedit_fields(struct mlx5e_priv *priv,
 				int namespace,
@@ -2689,13 +2884,13 @@
 				struct netlink_ext_ack *extack)
 {
 	struct pedit_headers *set_masks, *add_masks, *set_vals, *add_vals;
-	int i, action_size, first, last, next_z;
 	void *headers_c, *headers_v, *action, *vals_p;
-	u32 *s_masks_p, *a_masks_p, s_mask, a_mask;
 	struct mlx5e_tc_mod_hdr_acts *mod_acts;
+	void *s_masks_p, *a_masks_p;
+	int i, first, last, next_z;
 	struct mlx5_fields *f;
-	unsigned long mask, field_mask;
-	int err;
+	unsigned long mask;
+	u32 s_mask, a_mask;
 	u8 cmd;
 
 	mod_acts = &parse_attr->mod_hdr_acts;
@@ -2707,21 +2902,15 @@
 	set_vals = &hdrs[0].vals;
 	add_vals = &hdrs[1].vals;
 
-	action_size = MLX5_UN_SZ_BYTES(set_add_copy_action_in_auto);
-
 	for (i = 0; i < ARRAY_SIZE(fields); i++) {
 		bool skip;
 
 		f = &fields[i];
-		/* avoid seeing bits set from previous iterations */
-		s_mask = 0;
-		a_mask = 0;
-
 		s_masks_p = (void *)set_masks + f->offset;
 		a_masks_p = (void *)add_masks + f->offset;
 
-		s_mask = *s_masks_p & f->field_mask;
-		a_mask = *a_masks_p & f->field_mask;
+		s_mask = mask_field_get(s_masks_p, f);
+		a_mask = mask_field_get(a_masks_p, f);
 
 		if (!s_mask && !a_mask) /* nothing to offload here */
 			continue;
@@ -2748,22 +2937,20 @@
 					 match_mask, f->field_bsize))
 				skip = true;
 			/* clear to denote we consumed this field */
-			*s_masks_p &= ~f->field_mask;
+			mask_field_clear(s_masks_p, f);
 		} else {
 			cmd  = MLX5_ACTION_TYPE_ADD;
 			mask = a_mask;
 			vals_p = (void *)add_vals + f->offset;
 			/* add 0 is no change */
-			if ((*(u32 *)vals_p & f->field_mask) == 0)
+			if (!mask_field_get(vals_p, f))
 				skip = true;
 			/* clear to denote we consumed this field */
-			*a_masks_p &= ~f->field_mask;
+			mask_field_clear(a_masks_p, f);
 		}
 		if (skip)
 			continue;
 
-		mask = mask_to_le(mask, f->field_bsize);
-
 		first = find_first_bit(&mask, f->field_bsize);
 		next_z = find_next_zero_bit(&mask, f->field_bsize, first);
 		last  = find_last_bit(&mask, f->field_bsize);
@@ -2776,26 +2963,23 @@
 			return -EOPNOTSUPP;
 		}
 
-		err = alloc_mod_hdr_actions(priv->mdev, namespace, mod_acts);
-		if (err) {
+		action = mlx5e_mod_hdr_alloc(priv->mdev, namespace, mod_acts);
+		if (IS_ERR(action)) {
 			NL_SET_ERR_MSG_MOD(extack,
 					   "too many pedit actions, can't offload");
 			mlx5_core_warn(priv->mdev,
 				       "mlx5: parsed %d pedit actions, can't do more\n",
 				       mod_acts->num_actions);
-			return err;
+			return PTR_ERR(action);
 		}
 
-		action = mod_acts->actions +
-			 (mod_acts->num_actions * action_size);
 		MLX5_SET(set_action_in, action, action_type, cmd);
 		MLX5_SET(set_action_in, action, field, f->field);
 
 		if (cmd == MLX5_ACTION_TYPE_SET) {
+			unsigned long field_mask = f->field_mask;
 			int start;
 
-			field_mask = mask_to_le(f->field_mask, f->field_bsize);
-
 			/* if field is bit sized it can start not from first bit */
 			start = find_first_bit(&field_mask, f->field_bsize);
 
@@ -2817,57 +3001,6 @@
 	return 0;
 }
 
-static int mlx5e_flow_namespace_max_modify_action(struct mlx5_core_dev *mdev,
-						  int namespace)
-{
-	if (namespace == MLX5_FLOW_NAMESPACE_FDB) /* FDB offloading */
-		return MLX5_CAP_ESW_FLOWTABLE_FDB(mdev, max_modify_header_actions);
-	else /* namespace is MLX5_FLOW_NAMESPACE_KERNEL - NIC offloading */
-		return MLX5_CAP_FLOWTABLE_NIC_RX(mdev, max_modify_header_actions);
-}
-
-int alloc_mod_hdr_actions(struct mlx5_core_dev *mdev,
-			  int namespace,
-			  struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts)
-{
-	int action_size, new_num_actions, max_hw_actions;
-	size_t new_sz, old_sz;
-	void *ret;
-
-	if (mod_hdr_acts->num_actions < mod_hdr_acts->max_actions)
-		return 0;
-
-	action_size = MLX5_UN_SZ_BYTES(set_add_copy_action_in_auto);
-
-	max_hw_actions = mlx5e_flow_namespace_max_modify_action(mdev,
-								namespace);
-	new_num_actions = min(max_hw_actions,
-			      mod_hdr_acts->actions ?
-			      mod_hdr_acts->max_actions * 2 : 1);
-	if (mod_hdr_acts->max_actions == new_num_actions)
-		return -ENOSPC;
-
-	new_sz = action_size * new_num_actions;
-	old_sz = mod_hdr_acts->max_actions * action_size;
-	ret = krealloc(mod_hdr_acts->actions, new_sz, GFP_KERNEL);
-	if (!ret)
-		return -ENOMEM;
-
-	memset(ret + old_sz, 0, new_sz - old_sz);
-	mod_hdr_acts->actions = ret;
-	mod_hdr_acts->max_actions = new_num_actions;
-
-	return 0;
-}
-
-void dealloc_mod_hdr_actions(struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts)
-{
-	kfree(mod_hdr_acts->actions);
-	mod_hdr_acts->actions = NULL;
-	mod_hdr_acts->num_actions = 0;
-	mod_hdr_acts->max_actions = 0;
-}
-
 static const struct pedit_headers zero_masks = {};
 
 static int
@@ -2890,7 +3023,7 @@
 		goto out_err;
 	}
 
-	if (!mlx5e_flow_namespace_max_modify_action(priv->mdev, namespace)) {
+	if (!mlx5e_mod_hdr_max_actions(priv->mdev, namespace)) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "The pedit offload action is not supported");
 		goto out_err;
@@ -2982,7 +3115,7 @@
 	return 0;
 
 out_dealloc_parsed_actions:
-	dealloc_mod_hdr_actions(&parse_attr->mod_hdr_acts);
+	mlx5e_mod_hdr_dealloc(&parse_attr->mod_hdr_acts);
 	return err;
 }
 
@@ -3178,37 +3311,68 @@
 	return true;
 }
 
-static bool actions_match_supported(struct mlx5e_priv *priv,
-				    struct flow_action *flow_action,
-				    struct mlx5e_tc_flow_parse_attr *parse_attr,
-				    struct mlx5e_tc_flow *flow,
-				    struct netlink_ext_ack *extack)
+static bool
+actions_match_supported_fdb(struct mlx5e_priv *priv,
+			    struct mlx5e_tc_flow_parse_attr *parse_attr,
+			    struct mlx5e_tc_flow *flow,
+			    struct netlink_ext_ack *extack)
 {
-	bool ct_flow = false, ct_clear = false;
-	u32 actions;
+	bool ct_flow, ct_clear;
 
-	ct_clear = flow->attr->ct_attr.ct_action &
-		TCA_CT_ACT_CLEAR;
+	ct_clear = flow->attr->ct_attr.ct_action & TCA_CT_ACT_CLEAR;
 	ct_flow = flow_flag_test(flow, CT) && !ct_clear;
-	actions = flow->attr->action;
 
-	if (mlx5e_is_eswitch_flow(flow)) {
-		if (flow->attr->esw_attr->split_count && ct_flow &&
-		    !MLX5_CAP_GEN(flow->attr->esw_attr->in_mdev, reg_c_preserve)) {
-			/* All registers used by ct are cleared when using
-			 * split rules.
-			 */
-			NL_SET_ERR_MSG_MOD(extack,
-					   "Can't offload mirroring with action ct");
-			return false;
-		}
+	if (flow->attr->esw_attr->split_count && ct_flow &&
+	    !MLX5_CAP_GEN(flow->attr->esw_attr->in_mdev, reg_c_preserve)) {
+		/* All registers used by ct are cleared when using
+		 * split rules.
+		 */
+		NL_SET_ERR_MSG_MOD(extack, "Can't offload mirroring with action ct");
+		return false;
+	}
+
+	return true;
+}
+
+static bool
+actions_match_supported(struct mlx5e_priv *priv,
+			struct flow_action *flow_action,
+			struct mlx5e_tc_flow_parse_attr *parse_attr,
+			struct mlx5e_tc_flow *flow,
+			struct netlink_ext_ack *extack)
+{
+	u32 actions = flow->attr->action;
+	bool ct_flow, ct_clear;
+
+	ct_clear = flow->attr->ct_attr.ct_action & TCA_CT_ACT_CLEAR;
+	ct_flow = flow_flag_test(flow, CT) && !ct_clear;
+
+	if (!(actions &
+	      (MLX5_FLOW_CONTEXT_ACTION_FWD_DEST | MLX5_FLOW_CONTEXT_ACTION_DROP))) {
+		NL_SET_ERR_MSG_MOD(extack, "Rule must have at least one forward/drop action");
+		return false;
 	}
 
-	if (actions & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR)
-		return modify_header_match_supported(priv, &parse_attr->spec,
-						     flow_action, actions,
-						     ct_flow, ct_clear,
-						     extack);
+	if (!(~actions &
+	      (MLX5_FLOW_CONTEXT_ACTION_FWD_DEST | MLX5_FLOW_CONTEXT_ACTION_DROP))) {
+		NL_SET_ERR_MSG_MOD(extack, "Rule cannot support forward+drop action");
+		return false;
+	}
+
+	if (actions & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR &&
+	    actions & MLX5_FLOW_CONTEXT_ACTION_DROP) {
+		NL_SET_ERR_MSG_MOD(extack, "Drop with modify header action is not supported");
+		return false;
+	}
+
+	if (actions & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR &&
+	    !modify_header_match_supported(priv, &parse_attr->spec, flow_action,
+					   actions, ct_flow, ct_clear, extack))
+		return false;
+
+	if (mlx5e_is_eswitch_flow(flow) &&
+	    !actions_match_supported_fdb(priv, parse_attr, flow, extack))
+		return false;
 
 	return true;
 }
@@ -3357,11 +3521,51 @@
 	return 0;
 }
 
-static int parse_tc_nic_actions(struct mlx5e_priv *priv,
-				struct flow_action *flow_action,
+static int
+actions_prepare_mod_hdr_actions(struct mlx5e_priv *priv,
 				struct mlx5e_tc_flow *flow,
+				struct mlx5_flow_attr *attr,
+				struct pedit_headers_action *hdrs,
 				struct netlink_ext_ack *extack)
 {
+	struct mlx5e_tc_flow_parse_attr *parse_attr = attr->parse_attr;
+	enum mlx5_flow_namespace_type ns_type;
+	int err;
+
+	if (!hdrs[TCA_PEDIT_KEY_EX_CMD_SET].pedits &&
+	    !hdrs[TCA_PEDIT_KEY_EX_CMD_ADD].pedits)
+		return 0;
+
+	ns_type = get_flow_name_space(flow);
+
+	err = alloc_tc_pedit_action(priv, ns_type, parse_attr, hdrs,
+				    &attr->action, extack);
+	if (err)
+		return err;
+
+	/* In case all pedit actions are skipped, remove the MOD_HDR flag. */
+	if (parse_attr->mod_hdr_acts.num_actions > 0)
+		return 0;
+
+	attr->action &= ~MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
+	mlx5e_mod_hdr_dealloc(&parse_attr->mod_hdr_acts);
+
+	if (ns_type != MLX5_FLOW_NAMESPACE_FDB)
+		return 0;
+
+	if (!((attr->action & MLX5_FLOW_CONTEXT_ACTION_VLAN_POP) ||
+	      (attr->action & MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH)))
+		attr->esw_attr->split_count = 0;
+
+	return 0;
+}
+
+static int
+parse_tc_nic_actions(struct mlx5e_priv *priv,
+		     struct flow_action *flow_action,
+		     struct mlx5e_tc_flow *flow,
+		     struct netlink_ext_ack *extack)
+{
 	struct mlx5e_tc_flow_parse_attr *parse_attr;
 	struct mlx5_flow_attr *attr = flow->attr;
 	struct pedit_headers_action hdrs[2] = {};
@@ -3453,11 +3657,14 @@
 			if (err)
 				return err;
 
-			action |= MLX5_FLOW_CONTEXT_ACTION_COUNT;
+			action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST |
+				  MLX5_FLOW_CONTEXT_ACTION_COUNT;
 			attr->dest_chain = act->chain_index;
 			break;
 		case FLOW_ACTION_CT:
-			err = mlx5_tc_ct_parse_action(get_ct_priv(priv), attr, act, extack);
+			err = mlx5_tc_ct_parse_action(get_ct_priv(priv), attr,
+						      &parse_attr->mod_hdr_acts,
+						      act, extack);
 			if (err)
 				return err;
 
@@ -3469,33 +3676,16 @@
 		}
 	}
 
-	if (hdrs[TCA_PEDIT_KEY_EX_CMD_SET].pedits ||
-	    hdrs[TCA_PEDIT_KEY_EX_CMD_ADD].pedits) {
-		err = alloc_tc_pedit_action(priv, MLX5_FLOW_NAMESPACE_KERNEL,
-					    parse_attr, hdrs, &action, extack);
-		if (err)
-			return err;
-		/* in case all pedit actions are skipped, remove the MOD_HDR
-		 * flag.
-		 */
-		if (parse_attr->mod_hdr_acts.num_actions == 0) {
-			action &= ~MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
-			dealloc_mod_hdr_actions(&parse_attr->mod_hdr_acts);
-		}
-	}
-
 	attr->action = action;
 
-	if (attr->dest_chain) {
-		if (attr->action & MLX5_FLOW_CONTEXT_ACTION_FWD_DEST) {
-			NL_SET_ERR_MSG(extack, "Mirroring goto chain rules isn't supported");
-			return -EOPNOTSUPP;
-		}
-		attr->action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST;
+	if (attr->dest_chain && parse_attr->mirred_ifindex[0]) {
+		NL_SET_ERR_MSG(extack, "Mirroring goto chain rules isn't supported");
+		return -EOPNOTSUPP;
 	}
 
-	if (attr->action & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR)
-		attr->action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST;
+	err = actions_prepare_mod_hdr_actions(priv, flow, attr, hdrs, extack);
+	if (err)
+		return err;
 
 	if (!actions_match_supported(priv, flow_action, parse_attr, flow, extack))
 		return -EOPNOTSUPP;
@@ -3734,6 +3924,45 @@
 	return 0;
 }
 
+int mlx5e_set_fwd_to_int_port_actions(struct mlx5e_priv *priv,
+				      struct mlx5_flow_attr *attr,
+				      int ifindex,
+				      enum mlx5e_tc_int_port_type type,
+				      u32 *action,
+				      int out_index)
+{
+	struct mlx5_esw_flow_attr *esw_attr = attr->esw_attr;
+	struct mlx5e_tc_int_port_priv *int_port_priv;
+	struct mlx5e_tc_flow_parse_attr *parse_attr;
+	struct mlx5e_tc_int_port *dest_int_port;
+	int err;
+
+	parse_attr = attr->parse_attr;
+	int_port_priv = mlx5e_get_int_port_priv(priv);
+
+	dest_int_port = mlx5e_tc_int_port_get(int_port_priv, ifindex, type);
+	if (IS_ERR(dest_int_port))
+		return PTR_ERR(dest_int_port);
+
+	err = mlx5e_tc_match_to_reg_set(priv->mdev, &parse_attr->mod_hdr_acts,
+					MLX5_FLOW_NAMESPACE_FDB, VPORT_TO_REG,
+					mlx5e_tc_int_port_get_metadata(dest_int_port));
+	if (err) {
+		mlx5e_tc_int_port_put(int_port_priv, dest_int_port);
+		return err;
+	}
+
+	*action |= MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
+
+	esw_attr->dest_int_port = dest_int_port;
+	esw_attr->dests[out_index].flags |= MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE;
+
+	/* Forward to root fdb for matching against the new source vport */
+	attr->dest_chain = 0;
+
+	return 0;
+}
+
 static int parse_tc_fdb_actions(struct mlx5e_priv *priv,
 				struct flow_action *flow_action,
 				struct mlx5e_tc_flow *flow,
@@ -3753,6 +3982,7 @@
 	bool encap = false, decap = false;
 	u32 action = attr->action;
 	int err, i, if_count = 0;
+	bool ptype_host = false;
 	bool mpls_push = false;
 
 	if (!flow_action_has_entries(flow_action))
@@ -3767,6 +3997,20 @@
 
 	flow_action_for_each(i, act, flow_action) {
 		switch (act->id) {
+		case FLOW_ACTION_ACCEPT:
+			action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST |
+				MLX5_FLOW_CONTEXT_ACTION_COUNT;
+			attr->flags |= MLX5_ESW_ATTR_FLAG_ACCEPT;
+			break;
+		case FLOW_ACTION_PTYPE:
+			if (act->ptype != PACKET_HOST) {
+				NL_SET_ERR_MSG_MOD(extack,
+						   "skbedit ptype is only supported with type host");
+				return -EOPNOTSUPP;
+			}
+
+			ptype_host = true;
+			break;
 		case FLOW_ACTION_DROP:
 			action |= MLX5_FLOW_CONTEXT_ACTION_DROP |
 				  MLX5_FLOW_CONTEXT_ACTION_COUNT;
@@ -3830,6 +4074,50 @@
 				break;
 
 			return -EOPNOTSUPP;
+		case FLOW_ACTION_REDIRECT_INGRESS: {
+			struct net_device *out_dev;
+
+			out_dev = act->dev;
+			if (!out_dev)
+				return -EOPNOTSUPP;
+
+			if (!netif_is_ovs_master(out_dev)) {
+				NL_SET_ERR_MSG_MOD(extack,
+						   "redirect to ingress is supported only for OVS internal ports");
+				return -EOPNOTSUPP;
+			}
+
+			if (netif_is_ovs_master(parse_attr->filter_dev)) {
+				NL_SET_ERR_MSG_MOD(extack,
+						   "redirect to ingress is not supported from internal port");
+				return -EOPNOTSUPP;
+			}
+
+			if (!ptype_host) {
+				NL_SET_ERR_MSG_MOD(extack,
+						   "redirect to int port ingress requires ptype=host action");
+				return -EOPNOTSUPP;
+			}
+
+			if (esw_attr->out_count) {
+				NL_SET_ERR_MSG_MOD(extack,
+						   "redirect to int port ingress is supported only as single destination");
+				return -EOPNOTSUPP;
+			}
+
+			action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST |
+				  MLX5_FLOW_CONTEXT_ACTION_COUNT;
+
+			err = mlx5e_set_fwd_to_int_port_actions(priv, attr, out_dev->ifindex,
+								MLX5E_TC_INT_PORT_INGRESS,
+								&action, esw_attr->out_count);
+			if (err)
+				return err;
+
+			esw_attr->out_count++;
+
+			break;
+		}
 		case FLOW_ACTION_REDIRECT:
 		case FLOW_ACTION_MIRRED: {
 			struct mlx5e_priv *out_priv;
@@ -3937,6 +4225,16 @@
 				esw_attr->dests[esw_attr->out_count].rep = rpriv->rep;
 				esw_attr->dests[esw_attr->out_count].mdev = out_priv->mdev;
 				esw_attr->out_count++;
+			} else if (netif_is_ovs_master(out_dev)) {
+				err = mlx5e_set_fwd_to_int_port_actions(priv, attr,
+									out_dev->ifindex,
+									MLX5E_TC_INT_PORT_EGRESS,
+									&action,
+									esw_attr->out_count);
+				if (err)
+					return err;
+
+				esw_attr->out_count++;
 			} else if (parse_attr->filter_dev != priv->netdev) {
 				/* All mlx5 devices are called to configure
 				 * high level device filters. Therefore, the
@@ -4000,7 +4298,8 @@
 			if (err)
 				return err;
 
-			action |= MLX5_FLOW_CONTEXT_ACTION_COUNT;
+			action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST |
+				  MLX5_FLOW_CONTEXT_ACTION_COUNT;
 			attr->dest_chain = act->chain_index;
 			break;
 		case FLOW_ACTION_CT:
@@ -4008,7 +4307,9 @@
 				NL_SET_ERR_MSG_MOD(extack, "Sample action with connection tracking is not supported");
 				return -EOPNOTSUPP;
 			}
-			err = mlx5_tc_ct_parse_action(get_ct_priv(priv), attr, act, extack);
+			err = mlx5_tc_ct_parse_action(get_ct_priv(priv), attr,
+						      &parse_attr->mod_hdr_acts,
+						      act, extack);
 			if (err)
 				return err;
 
@@ -4032,6 +4333,14 @@
 		}
 	}
 
+	/* Forward to/from internal port can only have 1 dest */
+	if ((netif_is_ovs_master(parse_attr->filter_dev) || esw_attr->dest_int_port) &&
+	    esw_attr->out_count > 1) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Rules with internal port can have only one destination");
+		return -EOPNOTSUPP;
+	}
+
 	/* always set IP version for indirect table handling */
 	attr->ip_version = mlx5e_tc_get_ip_version(&parse_attr->spec, true);
 
@@ -4047,53 +4356,26 @@
 			return err;
 	}
 
-	if (hdrs[TCA_PEDIT_KEY_EX_CMD_SET].pedits ||
-	    hdrs[TCA_PEDIT_KEY_EX_CMD_ADD].pedits) {
-		err = alloc_tc_pedit_action(priv, MLX5_FLOW_NAMESPACE_FDB,
-					    parse_attr, hdrs, &action, extack);
-		if (err)
-			return err;
-		/* in case all pedit actions are skipped, remove the MOD_HDR
-		 * flag. we might have set split_count either by pedit or
-		 * pop/push. if there is no pop/push either, reset it too.
-		 */
-		if (parse_attr->mod_hdr_acts.num_actions == 0) {
-			action &= ~MLX5_FLOW_CONTEXT_ACTION_MOD_HDR;
-			dealloc_mod_hdr_actions(&parse_attr->mod_hdr_acts);
-			if (!((action & MLX5_FLOW_CONTEXT_ACTION_VLAN_POP) ||
-			      (action & MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH)))
-				esw_attr->split_count = 0;
-		}
-	}
-
 	attr->action = action;
-	if (!actions_match_supported(priv, flow_action, parse_attr, flow, extack))
-		return -EOPNOTSUPP;
 
-	if (attr->dest_chain) {
-		if (decap) {
-			/* It can be supported if we'll create a mapping for
-			 * the tunnel device only (without tunnel), and set
-			 * this tunnel id with this decap flow.
-			 *
-			 * On restore (miss), we'll just set this saved tunnel
-			 * device.
-			 */
+	err = actions_prepare_mod_hdr_actions(priv, flow, attr, hdrs, extack);
+	if (err)
+		return err;
 
-			NL_SET_ERR_MSG(extack,
-				       "Decap with goto isn't supported");
-			netdev_warn(priv->netdev,
-				    "Decap with goto isn't supported");
-			return -EOPNOTSUPP;
-		}
+	if (!actions_match_supported(priv, flow_action, parse_attr, flow, extack))
+		return -EOPNOTSUPP;
 
-		attr->action |= MLX5_FLOW_CONTEXT_ACTION_FWD_DEST;
-	}
+	if (attr->dest_chain && decap) {
+		/* It can be supported if we'll create a mapping for
+		 * the tunnel device only (without tunnel), and set
+		 * this tunnel id with this decap flow.
+		 *
+		 * On restore (miss), we'll just set this saved tunnel
+		 * device.
+		 */
 
-	if (!(attr->action &
-	      (MLX5_FLOW_CONTEXT_ACTION_FWD_DEST | MLX5_FLOW_CONTEXT_ACTION_DROP))) {
-		NL_SET_ERR_MSG_MOD(extack,
-				   "Rule must have at least one forward/drop action");
+		NL_SET_ERR_MSG(extack, "Decap with goto isn't supported");
+		netdev_warn(priv->netdev, "Decap with goto isn't supported");
 		return -EOPNOTSUPP;
 	}
 
@@ -4222,6 +4504,7 @@
 	INIT_LIST_HEAD(&flow->l3_to_l2_reformat);
 	refcount_set(&flow->refcnt, 1);
 	init_completion(&flow->init_done);
+	init_completion(&flow->del_hw_done);
 
 	*__flow = flow;
 	*__parse_attr = parse_attr;
@@ -4465,7 +4748,7 @@
 
 err_free:
 	flow_flag_set(flow, FAILED);
-	dealloc_mod_hdr_actions(&parse_attr->mod_hdr_acts);
+	mlx5e_mod_hdr_dealloc(&parse_attr->mod_hdr_acts);
 	mlx5e_flow_put(priv, flow);
 out:
 	return err;
@@ -4875,6 +5158,33 @@
 	return tc_tbl_size;
 }
 
+static int mlx5e_tc_nic_create_miss_table(struct mlx5e_priv *priv)
+{
+	struct mlx5_flow_table **ft = &priv->fs.tc.miss_t;
+	struct mlx5_flow_table_attr ft_attr = {};
+	struct mlx5_flow_namespace *ns;
+	int err = 0;
+
+	ft_attr.max_fte = 1;
+	ft_attr.autogroup.max_num_groups = 1;
+	ft_attr.level = MLX5E_TC_MISS_LEVEL;
+	ft_attr.prio = 0;
+	ns = mlx5_get_flow_namespace(priv->mdev, MLX5_FLOW_NAMESPACE_KERNEL);
+
+	*ft = mlx5_create_auto_grouped_flow_table(ns, &ft_attr);
+	if (IS_ERR(*ft)) {
+		err = PTR_ERR(*ft);
+		netdev_err(priv->netdev, "failed to create tc nic miss table err=%d\n", err);
+	}
+
+	return err;
+}
+
+static void mlx5e_tc_nic_destroy_miss_table(struct mlx5e_priv *priv)
+{
+	mlx5_destroy_flow_table(priv->fs.tc.miss_t);
+}
+
 int mlx5e_tc_nic_init(struct mlx5e_priv *priv)
 {
 	struct mlx5e_tc_table *tc = &priv->fs.tc;
@@ -4907,19 +5217,23 @@
 	}
 	tc->mapping = chains_mapping;
 
+	err = mlx5e_tc_nic_create_miss_table(priv);
+	if (err)
+		goto err_chains;
+
 	if (MLX5_CAP_FLOWTABLE_NIC_RX(priv->mdev, ignore_flow_level))
 		attr.flags = MLX5_CHAINS_AND_PRIOS_SUPPORTED |
 			MLX5_CHAINS_IGNORE_FLOW_LEVEL_SUPPORTED;
 	attr.ns = MLX5_FLOW_NAMESPACE_KERNEL;
 	attr.max_ft_sz = mlx5e_tc_nic_get_ft_size(dev);
 	attr.max_grp_num = MLX5E_TC_TABLE_NUM_GROUPS;
-	attr.default_ft = mlx5e_vlan_get_flowtable(priv->fs.vlan);
+	attr.default_ft = priv->fs.tc.miss_t;
 	attr.mapping = chains_mapping;
 
 	tc->chains = mlx5_chains_create(dev, &attr);
 	if (IS_ERR(tc->chains)) {
 		err = PTR_ERR(tc->chains);
-		goto err_chains;
+		goto err_miss;
 	}
 
 	tc->post_act = mlx5e_tc_post_act_init(priv, tc->chains, MLX5_FLOW_NAMESPACE_KERNEL);
@@ -4942,6 +5256,8 @@
 	mlx5_tc_ct_clean(tc->ct);
 	mlx5e_tc_post_act_destroy(tc->post_act);
 	mlx5_chains_destroy(tc->chains);
+err_miss:
+	mlx5e_tc_nic_destroy_miss_table(priv);
 err_chains:
 	mapping_destroy(chains_mapping);
 err_mapping:
@@ -4982,6 +5298,7 @@
 	mlx5e_tc_post_act_destroy(tc->post_act);
 	mapping_destroy(tc->mapping);
 	mlx5_chains_destroy(tc->chains);
+	mlx5e_tc_nic_destroy_miss_table(priv);
 }
 
 int mlx5e_tc_esw_init(struct rhashtable *tc_ht)
@@ -5008,9 +5325,9 @@
 					       MLX5_FLOW_NAMESPACE_FDB,
 					       uplink_priv->post_act);
 
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
+	uplink_priv->int_port_priv = mlx5e_tc_int_port_init(netdev_priv(priv->netdev));
+
 	uplink_priv->tc_psample = mlx5e_tc_sample_init(esw, uplink_priv->post_act);
-#endif
 
 	mapping_id = mlx5_query_nic_system_image_guid(esw->dev);
 
@@ -5054,9 +5371,8 @@
 err_enc_opts_mapping:
 	mapping_destroy(uplink_priv->tunnel_mapping);
 err_tun_mapping:
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
 	mlx5e_tc_sample_cleanup(uplink_priv->tc_psample);
-#endif
+	mlx5e_tc_int_port_cleanup(uplink_priv->int_port_priv);
 	mlx5_tc_ct_clean(uplink_priv->ct_priv);
 	netdev_warn(priv->netdev,
 		    "Failed to initialize tc (eswitch), err: %d", err);
@@ -5076,9 +5392,8 @@
 	mapping_destroy(uplink_priv->tunnel_enc_opts_mapping);
 	mapping_destroy(uplink_priv->tunnel_mapping);
 
-#if IS_ENABLED(CONFIG_MLX5_TC_SAMPLE)
 	mlx5e_tc_sample_cleanup(uplink_priv->tc_psample);
-#endif
+	mlx5e_tc_int_port_cleanup(uplink_priv->int_port_priv);
 	mlx5_tc_ct_clean(uplink_priv->ct_priv);
 	mlx5e_tc_post_act_destroy(uplink_priv->post_act);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_tc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_tc.h
@@ -38,6 +38,7 @@
 #include "eswitch.h"
 #include "en/tc_ct.h"
 #include "en/tc_tun.h"
+#include "en/tc/int_port.h"
 #include "en_rep.h"
 
 #define MLX5E_TC_FLOW_ID_MASK 0x0000ffff
@@ -56,7 +57,7 @@
 int mlx5e_tc_num_filters(struct mlx5e_priv *priv, unsigned long flags);
 
 struct mlx5e_tc_update_priv {
-	struct net_device *tun_dev;
+	struct net_device *fwd_dev;
 };
 
 struct mlx5_nic_flow_attr {
@@ -104,6 +105,8 @@
 #define MLX5E_TC_TABLE_CHAIN_TAG_BITS 16
 #define MLX5E_TC_TABLE_CHAIN_TAG_MASK GENMASK(MLX5E_TC_TABLE_CHAIN_TAG_BITS - 1, 0)
 
+#define MLX5E_TC_MAX_INT_PORT_NUM (8)
+
 #if IS_ENABLED(CONFIG_MLX5_CLS_ACT)
 
 struct tunnel_match_key {
@@ -241,13 +244,8 @@
 					 u32 data);
 
 int mlx5e_tc_add_flow_mod_hdr(struct mlx5e_priv *priv,
-			      struct mlx5e_tc_flow_parse_attr *parse_attr,
-			      struct mlx5e_tc_flow *flow);
-
-int alloc_mod_hdr_actions(struct mlx5_core_dev *mdev,
-			  int namespace,
-			  struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts);
-void dealloc_mod_hdr_actions(struct mlx5e_tc_mod_hdr_acts *mod_hdr_acts);
+			      struct mlx5e_tc_flow *flow,
+			      struct mlx5_flow_attr *attr);
 
 struct mlx5e_tc_flow;
 u32 mlx5e_tc_get_flow_tun_id(struct mlx5e_tc_flow *flow);
@@ -283,6 +281,12 @@
 int mlx5e_tc_query_route_vport(struct net_device *out_dev, struct net_device *route_dev,
 			       u16 *vport);
 
+int mlx5e_set_fwd_to_int_port_actions(struct mlx5e_priv *priv,
+				      struct mlx5_flow_attr *attr,
+				      int ifindex,
+				      enum mlx5e_tc_int_port_type type,
+				      u32 *action,
+				      int out_index);
 #else /* CONFIG_MLX5_CLS_ACT */
 static inline int  mlx5e_tc_nic_init(struct mlx5e_priv *priv) { return 0; }
 static inline void mlx5e_tc_nic_cleanup(struct mlx5e_priv *priv) {}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_tx.c
@@ -38,6 +38,7 @@
 #include "en/txrx.h"
 #include "ipoib/ipoib.h"
 #include "en_accel/en_accel.h"
+#include "en_accel/ipsec_rxtx.h"
 #include "en/ptp.h"
 
 static void mlx5e_dma_unmap_wqe_err(struct mlx5e_txqsq *sq, u8 num_dma)
@@ -213,30 +214,13 @@
 	memcpy(&vhdr->h_vlan_encapsulated_proto, skb->data + cpy1_sz, cpy2_sz);
 }
 
-static void
-ipsec_txwqe_build_eseg_csum(struct mlx5e_txqsq *sq, struct sk_buff *skb,
-			    struct mlx5_wqe_eth_seg *eseg)
-{
-	struct xfrm_offload *xo = xfrm_offload(skb);
-
-	eseg->cs_flags = MLX5_ETH_WQE_L3_CSUM;
-	if (xo->inner_ipproto) {
-		eseg->cs_flags |= MLX5_ETH_WQE_L4_INNER_CSUM | MLX5_ETH_WQE_L3_INNER_CSUM;
-	} else if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
-		eseg->cs_flags |= MLX5_ETH_WQE_L4_CSUM;
-		sq->stats->csum_partial_inner++;
-	}
-}
-
 static inline void
 mlx5e_txwqe_build_eseg_csum(struct mlx5e_txqsq *sq, struct sk_buff *skb,
 			    struct mlx5e_accel_tx_state *accel,
 			    struct mlx5_wqe_eth_seg *eseg)
 {
-	if (unlikely(mlx5e_ipsec_eseg_meta(eseg))) {
-		ipsec_txwqe_build_eseg_csum(sq, skb, eseg);
+	if (unlikely(mlx5e_ipsec_txwqe_build_eseg_csum(sq, skb, eseg)))
 		return;
-	}
 
 	if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
 		eseg->cs_flags = MLX5_ETH_WQE_L3_CSUM;
@@ -445,6 +429,26 @@
 	}
 }
 
+static void mlx5e_tx_flush(struct mlx5e_txqsq *sq)
+{
+	struct mlx5e_tx_wqe_info *wi;
+	struct mlx5e_tx_wqe *wqe;
+	u16 pi;
+
+	/* Must not be called when a MPWQE session is active but empty. */
+	mlx5e_tx_mpwqe_ensure_complete(sq);
+
+	pi = mlx5_wq_cyc_ctr2ix(&sq->wq, sq->pc);
+	wi = &sq->db.wqe_info[pi];
+
+	*wi = (struct mlx5e_tx_wqe_info) {
+		.num_wqebbs = 1,
+	};
+
+	wqe = mlx5e_post_nop(&sq->wq, sq->sqn, &sq->pc);
+	mlx5e_notify_hw(&sq->wq, sq->pc, sq->uar_map, &wqe->ctrl);
+}
+
 static inline void
 mlx5e_txwqe_complete(struct mlx5e_txqsq *sq, struct sk_buff *skb,
 		     const struct mlx5e_tx_attr *attr,
@@ -475,6 +479,11 @@
 	if (unlikely(sq->ptpsq)) {
 		mlx5e_skb_cb_hwtstamp_init(skb);
 		mlx5e_skb_fifo_push(&sq->ptpsq->skb_fifo, skb);
+		if (!netif_tx_queue_stopped(sq->txq) &&
+		    !mlx5e_skb_fifo_has_room(&sq->ptpsq->skb_fifo)) {
+			netif_tx_stop_queue(sq->txq);
+			sq->stats->stopped++;
+		}
 		skb_get(skb);
 	}
 
@@ -537,6 +546,7 @@
 err_drop:
 	stats->dropped++;
 	dev_kfree_skb_any(skb);
+	mlx5e_tx_flush(sq);
 }
 
 static bool mlx5e_tx_skb_supports_mpwqe(struct sk_buff *skb, struct mlx5e_tx_attr *attr)
@@ -638,6 +648,13 @@
 	struct mlx5_wqe_ctrl_seg *cseg;
 	struct mlx5e_xmit_data txd;
 
+	txd.data = skb->data;
+	txd.len = skb->len;
+
+	txd.dma_addr = dma_map_single(sq->pdev, txd.data, txd.len, DMA_TO_DEVICE);
+	if (unlikely(dma_mapping_error(sq->pdev, txd.dma_addr)))
+		goto err_unmap;
+
 	if (!mlx5e_tx_mpwqe_session_is_active(sq)) {
 		mlx5e_tx_mpwqe_session_start(sq, eseg);
 	} else if (!mlx5e_tx_mpwqe_same_eseg(sq, eseg)) {
@@ -647,18 +664,9 @@
 
 	sq->stats->xmit_more += xmit_more;
 
-	txd.data = skb->data;
-	txd.len = skb->len;
-
-	txd.dma_addr = dma_map_single(sq->pdev, txd.data, txd.len, DMA_TO_DEVICE);
-	if (unlikely(dma_mapping_error(sq->pdev, txd.dma_addr)))
-		goto err_unmap;
 	mlx5e_dma_push(sq, txd.dma_addr, txd.len, MLX5E_DMA_MAP_SINGLE);
-
 	mlx5e_skb_fifo_push(&sq->db.skb_fifo, skb);
-
 	mlx5e_tx_mpwqe_add_dseg(sq, &txd);
-
 	mlx5e_tx_skb_update_hwts_flags(skb);
 
 	if (unlikely(mlx5e_tx_mpwqe_is_full(&sq->mpwqe))) {
@@ -677,9 +685,9 @@
 	return;
 
 err_unmap:
-	mlx5e_dma_unmap_wqe_err(sq, 1);
 	sq->stats->dropped++;
 	dev_kfree_skb_any(skb);
+	mlx5e_tx_flush(sq);
 }
 
 void mlx5e_tx_mpwqe_ensure_complete(struct mlx5e_txqsq *sq)
@@ -801,6 +809,17 @@
 	}
 }
 
+void mlx5e_txqsq_wake(struct mlx5e_txqsq *sq)
+{
+	if (netif_tx_queue_stopped(sq->txq) &&
+	    mlx5e_wqc_has_room_for(&sq->wq, sq->cc, sq->pc, sq->stop_room) &&
+	    mlx5e_ptpsq_fifo_has_room(sq) &&
+	    !test_bit(MLX5E_SQ_STATE_RECOVERING, &sq->state)) {
+		netif_tx_wake_queue(sq->txq);
+		sq->stats->wake++;
+	}
+}
+
 bool mlx5e_poll_tx_cq(struct mlx5e_cq *cq, int napi_budget)
 {
 	struct mlx5e_sq_stats *stats;
@@ -900,12 +919,7 @@
 
 	netdev_tx_completed_queue(sq->txq, npkts, nbytes);
 
-	if (netif_tx_queue_stopped(sq->txq) &&
-	    mlx5e_wqc_has_room_for(&sq->wq, sq->cc, sq->pc, sq->stop_room) &&
-	    !test_bit(MLX5E_SQ_STATE_RECOVERING, &sq->state)) {
-		netif_tx_wake_queue(sq->txq);
-		stats->wake++;
-	}
+	mlx5e_txqsq_wake(sq);
 
 	return (i == MLX5E_TX_CQ_POLL_BUDGET);
 }
@@ -1049,5 +1063,6 @@
 err_drop:
 	stats->dropped++;
 	dev_kfree_skb_any(skb);
+	mlx5e_tx_flush(sq);
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/en_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/en_txrx.c
@@ -150,20 +150,22 @@
 		}
 	}
 
+	/* budget=0 means we may be in IRQ context, do as little as possible */
+	if (unlikely(!budget))
+		goto out;
+
 	busy |= mlx5e_poll_xdpsq_cq(&c->xdpsq.cq);
 
 	if (c->xdp)
 		busy |= mlx5e_poll_xdpsq_cq(&c->rq_xdpsq.cq);
 
-	if (likely(budget)) { /* budget=0 means: don't poll rx rings */
-		if (xsk_open)
-			work_done = mlx5e_poll_rx_cq(&xskrq->cq, budget);
+	if (xsk_open)
+		work_done = mlx5e_poll_rx_cq(&xskrq->cq, budget);
 
-		if (likely(budget - work_done))
-			work_done += mlx5e_poll_rx_cq(&rq->cq, budget - work_done);
+	if (likely(budget - work_done))
+		work_done += mlx5e_poll_rx_cq(&rq->cq, budget - work_done);
 
-		busy |= work_done == budget;
-	}
+	busy |= work_done == budget;
 
 	mlx5e_poll_ico_cq(&c->icosq.cq);
 	if (mlx5e_poll_ico_cq(&c->async_icosq.cq))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/eq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/eq.c
@@ -981,7 +981,7 @@
 	mutex_lock(&table->lock); /* sync with create/destroy_async_eq */
 	if (!mlx5_core_is_sf(dev))
 		clear_rmap(dev);
-	mlx5_irq_table_destroy(dev);
+	mlx5_irq_table_free_irqs(dev);
 	mutex_unlock(&table->lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_lgcy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_lgcy.c
@@ -67,6 +67,7 @@
 int esw_acl_egress_lgcy_setup(struct mlx5_eswitch *esw,
 			      struct mlx5_vport *vport)
 {
+	bool vst_mode_steering = esw_vst_mode_is_steering(esw);
 	struct mlx5_flow_destination drop_ctr_dst = {};
 	struct mlx5_flow_destination *dst = NULL;
 	struct mlx5_fc *drop_counter = NULL;
@@ -77,6 +78,7 @@
 	 */
 	int table_size = 2;
 	int dest_num = 0;
+	int actions_flag;
 	int err = 0;
 
 	if (vport->egress.legacy.drop_counter) {
@@ -119,8 +121,11 @@
 		  vport->vport, vport->info.vlan, vport->info.qos);
 
 	/* Allowed vlan rule */
+	actions_flag = MLX5_FLOW_CONTEXT_ACTION_ALLOW;
+	if (vst_mode_steering)
+		actions_flag |= MLX5_FLOW_CONTEXT_ACTION_VLAN_POP;
 	err = esw_egress_acl_vlan_create(esw, vport, NULL, vport->info.vlan,
-					 MLX5_FLOW_CONTEXT_ACTION_ALLOW);
+					 actions_flag);
 	if (err)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_lgcy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_lgcy.c
@@ -139,11 +139,14 @@
 int esw_acl_ingress_lgcy_setup(struct mlx5_eswitch *esw,
 			       struct mlx5_vport *vport)
 {
+	bool vst_mode_steering = esw_vst_mode_is_steering(esw);
 	struct mlx5_flow_destination drop_ctr_dst = {};
 	struct mlx5_flow_destination *dst = NULL;
 	struct mlx5_flow_act flow_act = {};
 	struct mlx5_flow_spec *spec = NULL;
 	struct mlx5_fc *counter = NULL;
+	bool vst_check_cvlan = false;
+	bool vst_push_cvlan = false;
 	/* The ingress acl table contains 4 groups
 	 * (2 active rules at the same time -
 	 *      1 allow rule from one of the first 3 groups.
@@ -203,7 +206,26 @@
 		goto out;
 	}
 
-	if (vport->info.vlan || vport->info.qos)
+	if ((vport->info.vlan || vport->info.qos)) {
+		if (vst_mode_steering)
+			vst_push_cvlan = true;
+		else if (!MLX5_CAP_ESW(esw->dev, vport_cvlan_insert_always))
+			vst_check_cvlan = true;
+	}
+
+	if (vst_check_cvlan || vport->info.spoofchk)
+		spec->match_criteria_enable = MLX5_MATCH_OUTER_HEADERS;
+
+	/* Create ingress allow rule */
+	flow_act.action = MLX5_FLOW_CONTEXT_ACTION_ALLOW;
+	if (vst_push_cvlan) {
+		flow_act.action |= MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH;
+		flow_act.vlan[0].prio = vport->info.qos;
+		flow_act.vlan[0].vid = vport->info.vlan;
+		flow_act.vlan[0].ethtype = ETH_P_8021Q;
+	}
+
+	if (vst_check_cvlan)
 		MLX5_SET_TO_ONES(fte_match_param, spec->match_criteria,
 				 outer_headers.cvlan_tag);
 
@@ -218,9 +240,6 @@
 		ether_addr_copy(smac_v, vport->info.mac);
 	}
 
-	/* Create ingress allow rule */
-	spec->match_criteria_enable = MLX5_MATCH_OUTER_HEADERS;
-	flow_act.action = MLX5_FLOW_CONTEXT_ACTION_ALLOW;
 	vport->ingress.allow_rule = mlx5_add_flow_rules(vport->ingress.acl, spec,
 							&flow_act, NULL, 0);
 	if (IS_ERR(vport->ingress.allow_rule)) {
@@ -232,6 +251,9 @@
 		goto out;
 	}
 
+	if (!vst_check_cvlan && !vport->info.spoofchk)
+		goto out;
+
 	memset(&flow_act, 0, sizeof(flow_act));
 	flow_act.action = MLX5_FLOW_CONTEXT_ACTION_DROP;
 	/* Attach drop flow counter */
@@ -257,7 +279,8 @@
 	return 0;
 
 out:
-	esw_acl_ingress_lgcy_cleanup(esw, vport);
+	if (err)
+		esw_acl_ingress_lgcy_cleanup(esw, vport);
 	kvfree(spec);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_ofld.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_ofld.c
@@ -301,8 +301,7 @@
 
 	if (WARN_ON_ONCE(IS_ERR(vport))) {
 		esw_warn(esw->dev, "vport(%d) invalid!\n", vport_num);
-		err = PTR_ERR(vport);
-		goto out;
+		return PTR_ERR(vport);
 	}
 
 	esw_acl_ingress_ofld_rules_destroy(esw, vport);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/bridge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/bridge.c
@@ -1270,7 +1270,7 @@
 	struct mlx5_esw_bridge *bridge;
 
 	port = mlx5_esw_bridge_port_lookup(vport_num, esw_owner_vhca_id, br_offloads);
-	if (!port || port->flags & MLX5_ESW_BRIDGE_PORT_FLAG_PEER)
+	if (!port)
 		return;
 
 	bridge = port->bridge;
@@ -1385,6 +1385,8 @@
 {
 	struct mlx5_esw_bridge_offloads *br_offloads;
 
+	ASSERT_RTNL();
+
 	br_offloads = kvzalloc(sizeof(*br_offloads), GFP_KERNEL);
 	if (!br_offloads)
 		return ERR_PTR(-ENOMEM);
@@ -1401,6 +1403,8 @@
 {
 	struct mlx5_esw_bridge_offloads *br_offloads = esw->br_offloads;
 
+	ASSERT_RTNL();
+
 	if (!br_offloads)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h
@@ -21,7 +21,7 @@
 			    __field(unsigned int, used)
 			    ),
 		    TP_fast_assign(
-			    strncpy(__entry->dev_name,
+			    strscpy(__entry->dev_name,
 				    netdev_name(fdb->dev),
 				    IFNAMSIZ);
 			    memcpy(__entry->addr, fdb->key.addr, ETH_ALEN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/indir_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/indir_table.c
@@ -14,6 +14,7 @@
 #include "fs_core.h"
 #include "esw/indir_table.h"
 #include "lib/fs_chains.h"
+#include "en/mod_hdr.h"
 
 #define MLX5_ESW_INDIR_TABLE_SIZE 128
 #define MLX5_ESW_INDIR_TABLE_RECIRC_IDX_MAX (MLX5_ESW_INDIR_TABLE_SIZE - 2)
@@ -226,7 +227,7 @@
 		goto err_handle;
 	}
 
-	dealloc_mod_hdr_actions(&mod_acts);
+	mlx5e_mod_hdr_dealloc(&mod_acts);
 	rule->handle = handle;
 	rule->vni = esw_attr->rx_tun_attr->vni;
 	rule->mh = flow_act.modify_hdr;
@@ -243,7 +244,7 @@
 	mlx5_modify_header_dealloc(esw->dev, flow_act.modify_hdr);
 err_mod_hdr_alloc:
 err_mod_hdr_regc1:
-	dealloc_mod_hdr_actions(&mod_acts);
+	mlx5e_mod_hdr_dealloc(&mod_acts);
 err_mod_hdr_regc0:
 err_ethertype:
 	kfree(rule);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/legacy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/legacy.c
@@ -11,6 +11,7 @@
 #include "mlx5_core.h"
 #include "eswitch.h"
 #include "fs_core.h"
+#include "fs_ft_pool.h"
 #include "esw/qos.h"
 
 enum {
@@ -95,8 +96,7 @@
 	if (!flow_group_in)
 		return -ENOMEM;
 
-	table_size = BIT(MLX5_CAP_ESW_FLOWTABLE_FDB(dev, log_max_ft_size));
-	ft_attr.max_fte = table_size;
+	ft_attr.max_fte = POOL_NEXT_SIZE;
 	ft_attr.prio = LEGACY_FDB_PRIO;
 	fdb = mlx5_create_flow_table(root_ns, &ft_attr);
 	if (IS_ERR(fdb)) {
@@ -105,6 +105,7 @@
 		goto out;
 	}
 	esw->fdb_table.legacy.fdb = fdb;
+	table_size = fdb->max_fte;
 
 	/* Addresses group : Full match unicast/multicast addresses */
 	MLX5_SET(create_flow_group_in, flow_group_in, match_criteria_enable,
@@ -431,7 +432,7 @@
 	int err = 0;
 
 	if (!mlx5_esw_allowed(esw))
-		return -EPERM;
+		return vlan ? -EPERM : 0;
 
 	if (vlan || qos)
 		set_flags = SET_VLAN_STRIP | SET_VLAN_INSERT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c
@@ -22,15 +22,13 @@
 };
 
 static int esw_qos_tsar_config(struct mlx5_core_dev *dev, u32 *sched_ctx,
-			       u32 parent_ix, u32 tsar_ix,
-			       u32 max_rate, u32 bw_share)
+			       u32 tsar_ix, u32 max_rate, u32 bw_share)
 {
 	u32 bitmask = 0;
 
 	if (!MLX5_CAP_GEN(dev, qos) || !MLX5_CAP_QOS(dev, esw_scheduling))
 		return -EOPNOTSUPP;
 
-	MLX5_SET(scheduling_context, sched_ctx, parent_element_id, parent_ix);
 	MLX5_SET(scheduling_context, sched_ctx, max_average_bw, max_rate);
 	MLX5_SET(scheduling_context, sched_ctx, bw_share, bw_share);
 	bitmask |= MODIFY_SCHEDULING_ELEMENT_IN_MODIFY_BITMASK_MAX_AVERAGE_BW;
@@ -51,7 +49,7 @@
 	int err;
 
 	err = esw_qos_tsar_config(dev, sched_ctx,
-				  esw->qos.root_tsar_ix, group->tsar_ix,
+				  group->tsar_ix,
 				  max_rate, bw_share);
 	if (err)
 		NL_SET_ERR_MSG_MOD(extack, "E-Switch modify group TSAR element failed");
@@ -67,23 +65,13 @@
 				struct netlink_ext_ack *extack)
 {
 	u32 sched_ctx[MLX5_ST_SZ_DW(scheduling_context)] = {};
-	struct mlx5_esw_rate_group *group = vport->qos.group;
 	struct mlx5_core_dev *dev = esw->dev;
-	u32 parent_tsar_ix;
-	void *vport_elem;
 	int err;
 
 	if (!vport->qos.enabled)
 		return -EIO;
 
-	parent_tsar_ix = group ? group->tsar_ix : esw->qos.root_tsar_ix;
-	MLX5_SET(scheduling_context, sched_ctx, element_type,
-		 SCHEDULING_CONTEXT_ELEMENT_TYPE_VPORT);
-	vport_elem = MLX5_ADDR_OF(scheduling_context, sched_ctx,
-				  element_attributes);
-	MLX5_SET(vport_element, vport_elem, vport_number, vport->vport);
-
-	err = esw_qos_tsar_config(dev, sched_ctx, parent_tsar_ix, vport->qos.esw_tsar_ix,
+	err = esw_qos_tsar_config(dev, sched_ctx, vport->qos.esw_tsar_ix,
 				  max_rate, bw_share);
 	if (err) {
 		esw_warn(esw->dev,
@@ -130,7 +118,7 @@
 	/* If vports min rate divider is 0 but their group has bw_share configured, then
 	 * need to set bw_share for vports to minimal value.
 	 */
-	if (!group_level && !max_guarantee && group->bw_share)
+	if (!group_level && !max_guarantee && group && group->bw_share)
 		return 1;
 	return 0;
 }
@@ -423,7 +411,7 @@
 		return err;
 
 	/* Recalculate bw share weights of old and new groups */
-	if (vport->qos.bw_share) {
+	if (vport->qos.bw_share || new_group->bw_share) {
 		esw_qos_normalize_vports_min_rate(esw, curr_group, extack);
 		esw_qos_normalize_vports_min_rate(esw, new_group, extack);
 	}
@@ -436,6 +424,7 @@
 {
 	u32 tsar_ctx[MLX5_ST_SZ_DW(scheduling_context)] = {};
 	struct mlx5_esw_rate_group *group;
+	__be32 *attr;
 	u32 divider;
 	int err;
 
@@ -446,6 +435,12 @@
 	if (!group)
 		return ERR_PTR(-ENOMEM);
 
+	MLX5_SET(scheduling_context, tsar_ctx, element_type,
+		 SCHEDULING_CONTEXT_ELEMENT_TYPE_TSAR);
+
+	attr = MLX5_ADDR_OF(scheduling_context, tsar_ctx, element_attributes);
+	*attr = cpu_to_be32(TSAR_ELEMENT_TSAR_TYPE_DWRR << 16);
+
 	MLX5_SET(scheduling_context, tsar_ctx, parent_element_id,
 		 esw->qos.root_tsar_ix);
 	err = mlx5_create_scheduling_element_cmd(esw->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c
@@ -160,10 +160,17 @@
 			 esw_vport_context.vport_cvlan_strip, 1);
 
 	if (set_flags & SET_VLAN_INSERT) {
-		/* insert only if no vlan in packet */
-		MLX5_SET(modify_esw_vport_context_in, in,
-			 esw_vport_context.vport_cvlan_insert, 1);
-
+		if (MLX5_CAP_ESW(dev, vport_cvlan_insert_always)) {
+			/* insert either if vlan exist in packet or not */
+			MLX5_SET(modify_esw_vport_context_in, in,
+				 esw_vport_context.vport_cvlan_insert,
+				 MLX5_VPORT_CVLAN_INSERT_ALWAYS);
+		} else {
+			/* insert only if no vlan in packet */
+			MLX5_SET(modify_esw_vport_context_in, in,
+				 esw_vport_context.vport_cvlan_insert,
+				 MLX5_VPORT_CVLAN_INSERT_WHEN_NO_CVLAN);
+		}
 		MLX5_SET(modify_esw_vport_context_in, in,
 			 esw_vport_context.cvlan_pcp, qos);
 		MLX5_SET(modify_esw_vport_context_in, in,
@@ -773,6 +780,7 @@
 
 static int esw_vport_setup(struct mlx5_eswitch *esw, struct mlx5_vport *vport)
 {
+	bool vst_mode_steering = esw_vst_mode_is_steering(esw);
 	u16 vport_num = vport->vport;
 	int flags;
 	int err;
@@ -802,8 +810,9 @@
 
 	flags = (vport->info.vlan || vport->info.qos) ?
 		SET_VLAN_STRIP | SET_VLAN_INSERT : 0;
-	modify_esw_vport_cvlan(esw->dev, vport_num, vport->info.vlan,
-			       vport->info.qos, flags);
+	if (esw->mode == MLX5_ESWITCH_OFFLOADS || !vst_mode_steering)
+		modify_esw_vport_cvlan(esw->dev, vport_num, vport->info.vlan,
+				       vport->info.qos, flags);
 
 	return 0;
 }
@@ -909,6 +918,7 @@
 	 */
 	esw_vport_change_handle_locked(vport);
 	vport->enabled_events = 0;
+	esw_apply_vport_rx_mode(esw, vport, false, false);
 	esw_vport_cleanup(esw, vport);
 	esw->enabled_vports--;
 
@@ -1305,12 +1315,17 @@
  */
 int mlx5_eswitch_enable(struct mlx5_eswitch *esw, int num_vfs)
 {
+	bool toggle_lag;
 	int ret;
 
 	if (!mlx5_esw_allowed(esw))
 		return 0;
 
-	mlx5_lag_disable_change(esw->dev);
+	toggle_lag = esw->mode == MLX5_ESWITCH_NONE;
+
+	if (toggle_lag)
+		mlx5_lag_disable_change(esw->dev);
+
 	down_write(&esw->mode_lock);
 	if (esw->mode == MLX5_ESWITCH_NONE) {
 		ret = mlx5_eswitch_enable_locked(esw, MLX5_ESWITCH_LEGACY, num_vfs);
@@ -1324,7 +1339,10 @@
 			esw->esw_funcs.num_vfs = num_vfs;
 	}
 	up_write(&esw->mode_lock);
-	mlx5_lag_enable_change(esw->dev);
+
+	if (toggle_lag)
+		mlx5_lag_enable_change(esw->dev);
+
 	return ret;
 }
 
@@ -1572,6 +1590,11 @@
 	esw->enabled_vports = 0;
 	esw->mode = MLX5_ESWITCH_NONE;
 	esw->offloads.inline_mode = MLX5_INLINE_MODE_NONE;
+	if (MLX5_CAP_ESW_FLOWTABLE_FDB(dev, reformat) &&
+	    MLX5_CAP_ESW_FLOWTABLE_FDB(dev, decap))
+		esw->offloads.encap = DEVLINK_ESWITCH_ENCAP_MODE_BASIC;
+	else
+		esw->offloads.encap = DEVLINK_ESWITCH_ENCAP_MODE_NONE;
 
 	dev->priv.eswitch = esw;
 	BLOCKING_INIT_NOTIFIER_HEAD(&esw->n_head);
@@ -1833,6 +1856,7 @@
 				  u16 vport, u16 vlan, u8 qos, u8 set_flags)
 {
 	struct mlx5_vport *evport = mlx5_eswitch_get_vport(esw, vport);
+	bool vst_mode_steering = esw_vst_mode_is_steering(esw);
 	int err = 0;
 
 	if (IS_ERR(evport))
@@ -1840,9 +1864,11 @@
 	if (vlan > 4095 || qos > 7)
 		return -EINVAL;
 
-	err = modify_esw_vport_cvlan(esw->dev, vport, vlan, qos, set_flags);
-	if (err)
-		return err;
+	if (esw->mode == MLX5_ESWITCH_OFFLOADS || !vst_mode_steering) {
+		err = modify_esw_vport_cvlan(esw->dev, vport, vlan, qos, set_flags);
+		if (err)
+			return err;
+	}
 
 	evport->info.vlan = vlan;
 	evport->info.qos = qos;
@@ -1934,7 +1960,7 @@
 	return err;
 }
 
-u8 mlx5_eswitch_mode(struct mlx5_core_dev *dev)
+u8 mlx5_eswitch_mode(const struct mlx5_core_dev *dev)
 {
 	struct mlx5_eswitch *esw = dev->priv.eswitch;
 
@@ -1948,7 +1974,7 @@
 	struct mlx5_eswitch *esw;
 
 	esw = dev->priv.eswitch;
-	return mlx5_esw_allowed(esw) ? esw->offloads.encap :
+	return (mlx5_eswitch_mode(dev) == MLX5_ESWITCH_OFFLOADS)  ? esw->offloads.encap :
 		DEVLINK_ESWITCH_ENCAP_MODE_NONE;
 }
 EXPORT_SYMBOL(mlx5_eswitch_get_encap_mode);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/eswitch.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/eswitch.h
@@ -51,6 +51,7 @@
 enum mlx5_mapped_obj_type {
 	MLX5_MAPPED_OBJ_CHAIN,
 	MLX5_MAPPED_OBJ_SAMPLE,
+	MLX5_MAPPED_OBJ_INT_PORT_METADATA,
 };
 
 struct mlx5_mapped_obj {
@@ -63,6 +64,7 @@
 			u32 trunc_size;
 			u32 tunnel_id;
 		} sample;
+		u32 int_port_metadata;
 	};
 };
 
@@ -88,6 +90,7 @@
 	MAPPING_TYPE_TUNNEL_ENC_OPTS,
 	MAPPING_TYPE_LABELS,
 	MAPPING_TYPE_ZONE,
+	MAPPING_TYPE_INT_PORT,
 };
 
 struct vport_ingress {
@@ -336,6 +339,9 @@
 
 int mlx5_esw_qos_modify_vport_rate(struct mlx5_eswitch *esw, u16 vport_num, u32 rate_mbps);
 
+bool mlx5_esw_vport_match_metadata_supported(const struct mlx5_eswitch *esw);
+int mlx5_esw_offloads_vport_metadata_set(struct mlx5_eswitch *esw, bool enable);
+
 /* E-Switch API */
 int mlx5_eswitch_init(struct mlx5_core_dev *dev);
 void mlx5_eswitch_cleanup(struct mlx5_eswitch *esw);
@@ -447,12 +453,22 @@
 	MLX5_ESW_ATTR_FLAG_NO_IN_PORT    = BIT(2),
 	MLX5_ESW_ATTR_FLAG_SRC_REWRITE   = BIT(3),
 	MLX5_ESW_ATTR_FLAG_SAMPLE        = BIT(4),
+	MLX5_ESW_ATTR_FLAG_ACCEPT        = BIT(5),
 };
 
+/* Returns true if any of the flags that require skipping further TC/NF processing are set. */
+static inline bool
+mlx5_esw_attr_flags_skip(u32 attr_flags)
+{
+	return attr_flags & (MLX5_ESW_ATTR_FLAG_SLOW_PATH | MLX5_ESW_ATTR_FLAG_ACCEPT);
+}
+
 struct mlx5_esw_flow_attr {
 	struct mlx5_eswitch_rep *in_rep;
 	struct mlx5_core_dev	*in_mdev;
 	struct mlx5_core_dev    *counter_dev;
+	struct mlx5e_tc_int_port *dest_int_port;
+	struct mlx5e_tc_int_port *int_port;
 
 	int split_count;
 	int out_count;
@@ -505,6 +521,12 @@
 	return esw->qos.enabled;
 }
 
+static inline bool esw_vst_mode_is_steering(struct mlx5_eswitch *esw)
+{
+	return (MLX5_CAP_ESW_EGRESS_ACL(esw->dev, pop_vlan) &&
+		MLX5_CAP_ESW_INGRESS_ACL(esw->dev, push_vlan));
+}
+
 static inline bool mlx5_eswitch_vlan_actions_supported(struct mlx5_core_dev *dev,
 						       u8 vlan_depth)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
@@ -86,12 +86,18 @@
 				  struct mlx5_flow_spec *spec,
 				  struct mlx5_esw_flow_attr *attr)
 {
-	if (MLX5_CAP_ESW_FLOWTABLE(esw->dev, flow_source) &&
-	    attr && attr->in_rep)
-		spec->flow_context.flow_source =
-			attr->in_rep->vport == MLX5_VPORT_UPLINK ?
-				MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK :
-				MLX5_FLOW_CONTEXT_FLOW_SOURCE_LOCAL_VPORT;
+	if (!MLX5_CAP_ESW_FLOWTABLE(esw->dev, flow_source) || !attr || !attr->in_rep)
+		return;
+
+	if (attr->int_port) {
+		spec->flow_context.flow_source = mlx5e_tc_int_port_get_flow_source(attr->int_port);
+
+		return;
+	}
+
+	spec->flow_context.flow_source = (attr->in_rep->vport == MLX5_VPORT_UPLINK) ?
+					 MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK :
+					 MLX5_FLOW_CONTEXT_FLOW_SOURCE_LOCAL_VPORT;
 }
 
 /* Actually only the upper 16 bits of reg c0 need to be cleared, but the lower 16 bits
@@ -121,6 +127,8 @@
 				  struct mlx5_eswitch *src_esw,
 				  u16 vport)
 {
+	struct mlx5_esw_flow_attr *esw_attr = attr->esw_attr;
+	u32 metadata;
 	void *misc2;
 	void *misc;
 
@@ -130,10 +138,16 @@
 	if (mlx5_eswitch_vport_match_metadata_enabled(esw)) {
 		if (mlx5_esw_indir_table_decap_vport(attr))
 			vport = mlx5_esw_indir_table_decap_vport(attr);
+
+		if (attr && !attr->chain && esw_attr->int_port)
+			metadata =
+				mlx5e_tc_int_port_get_metadata_for_match(esw_attr->int_port);
+		else
+			metadata =
+				mlx5_eswitch_get_vport_metadata_for_match(src_esw, vport);
+
 		misc2 = MLX5_ADDR_OF(fte_match_param, spec->match_value, misc_parameters_2);
-		MLX5_SET(fte_match_set_misc2, misc2, metadata_reg_c_0,
-			 mlx5_eswitch_get_vport_metadata_for_match(src_esw,
-								   vport));
+		MLX5_SET(fte_match_set_misc2, misc2, metadata_reg_c_0, metadata);
 
 		misc2 = MLX5_ADDR_OF(fte_match_param, spec->match_criteria, misc_parameters_2);
 		MLX5_SET(fte_match_set_misc2, misc2, metadata_reg_c_0,
@@ -281,23 +295,28 @@
 				 int *i)
 {
 	struct mlx5_esw_flow_attr *esw_attr = attr->esw_attr;
-	int j, err;
+	int err;
 
 	if (!(attr->flags & MLX5_ESW_ATTR_FLAG_SRC_REWRITE))
 		return -EOPNOTSUPP;
 
-	for (j = esw_attr->split_count; j < esw_attr->out_count; j++, (*i)++) {
-		err = esw_setup_chain_dest(dest, flow_act, chains, attr->dest_chain, 1, 0, *i);
-		if (err)
-			goto err_setup_chain;
+	/* flow steering cannot handle more than one dest with the same ft
+	 * in a single flow
+	 */
+	if (esw_attr->out_count - esw_attr->split_count > 1)
+		return -EOPNOTSUPP;
+
+	err = esw_setup_chain_dest(dest, flow_act, chains, attr->dest_chain, 1, 0, *i);
+	if (err)
+		return err;
+
+	if (esw_attr->dests[esw_attr->split_count].pkt_reformat) {
 		flow_act->action |= MLX5_FLOW_CONTEXT_ACTION_PACKET_REFORMAT;
-		flow_act->pkt_reformat = esw_attr->dests[j].pkt_reformat;
+		flow_act->pkt_reformat = esw_attr->dests[esw_attr->split_count].pkt_reformat;
 	}
-	return 0;
+	(*i)++;
 
-err_setup_chain:
-	esw_put_dest_tables_loop(esw, attr, esw_attr->split_count, j);
-	return err;
+	return 0;
 }
 
 static void esw_cleanup_chain_src_port_rewrite(struct mlx5_eswitch *esw,
@@ -315,7 +334,8 @@
 	int i;
 
 	for (i = esw_attr->split_count; i < esw_attr->out_count; i++)
-		if (mlx5_esw_indir_table_needed(esw, attr, esw_attr->dests[i].rep->vport,
+		if (esw_attr->dests[i].rep &&
+		    mlx5_esw_indir_table_needed(esw, attr, esw_attr->dests[i].rep->vport,
 						esw_attr->dests[i].mdev))
 			return true;
 	return false;
@@ -440,7 +460,7 @@
 	} else if (attr->dest_ft) {
 		esw_setup_ft_dest(dest, flow_act, esw, attr, spec, *i);
 		(*i)++;
-	} else if (attr->flags & MLX5_ESW_ATTR_FLAG_SLOW_PATH) {
+	} else if (mlx5_esw_attr_flags_skip(attr->flags)) {
 		esw_setup_slow_path_dest(dest, flow_act, chains, *i);
 		(*i)++;
 	} else if (attr->dest_chain) {
@@ -467,7 +487,7 @@
 
 	if (attr->dest_ft) {
 		esw_cleanup_decap_indir(esw, attr);
-	} else if (!(attr->flags & MLX5_ESW_ATTR_FLAG_SLOW_PATH)) {
+	} else if (!mlx5_esw_attr_flags_skip(attr->flags)) {
 		if (attr->dest_chain)
 			esw_cleanup_chain_dest(chains, attr->dest_chain, 1, 0);
 		else if (esw_is_indir_table(esw, attr))
@@ -656,7 +676,6 @@
 
 	return rule;
 err_chain_src_rewrite:
-	esw_put_dest_tables_loop(esw, attr, 0, i);
 	mlx5_esw_vporttbl_put(esw, &fwd_attr);
 err_get_fwd:
 	mlx5_chains_put_table(chains, attr->chain, attr->prio, 0);
@@ -678,7 +697,7 @@
 
 	mlx5_del_flow_rules(rule);
 
-	if (!(attr->flags & MLX5_ESW_ATTR_FLAG_SLOW_PATH)) {
+	if (!mlx5_esw_attr_flags_skip(attr->flags)) {
 		/* unref the term table */
 		for (i = 0; i < MLX5_MAX_FLOW_FWD_VPORTS; i++) {
 			if (esw_attr->dests[i].termtbl)
@@ -698,7 +717,6 @@
 	if (fwd_rule)  {
 		mlx5_esw_vporttbl_put(esw, &fwd_attr);
 		mlx5_chains_put_table(chains, attr->chain, attr->prio, 0);
-		esw_put_dest_tables_loop(esw, attr, 0, esw_attr->split_count);
 	} else {
 		if (split)
 			mlx5_esw_vporttbl_put(esw, &fwd_attr);
@@ -962,7 +980,8 @@
 	dest.vport.flags |= MLX5_FLOW_DEST_VPORT_VHCA_ID;
 	flow_act.action = MLX5_FLOW_CONTEXT_ACTION_FWD_DEST;
 
-	if (rep->vport == MLX5_VPORT_UPLINK)
+	if (MLX5_CAP_ESW_FLOWTABLE(on_esw->dev, flow_source) &&
+	    rep->vport == MLX5_VPORT_UPLINK)
 		spec->flow_context.flow_source = MLX5_FLOW_CONTEXT_FLOW_SOURCE_LOCAL_VPORT;
 
 	flow_rule = mlx5_add_flow_rules(on_esw->fdb_table.offloads.slow_fdb,
@@ -1845,6 +1864,17 @@
 	atomic64_set(&esw->user_count, 0);
 }
 
+static int esw_get_offloads_ft_size(struct mlx5_eswitch *esw)
+{
+	int nvports;
+
+	nvports = esw->total_vports + MLX5_ESW_MISS_FLOWS;
+	if (mlx5e_tc_int_port_supported(esw))
+		nvports += MLX5E_TC_MAX_INT_PORT_NUM;
+
+	return nvports;
+}
+
 static int esw_create_offloads_table(struct mlx5_eswitch *esw)
 {
 	struct mlx5_flow_table_attr ft_attr = {};
@@ -1859,7 +1889,7 @@
 		return -EOPNOTSUPP;
 	}
 
-	ft_attr.max_fte = esw->total_vports + MLX5_ESW_MISS_FLOWS;
+	ft_attr.max_fte = esw_get_offloads_ft_size(esw);
 	ft_attr.prio = 1;
 
 	ft_offloads = mlx5_create_flow_table(ns, &ft_attr);
@@ -1888,7 +1918,7 @@
 	int nvports;
 	int err = 0;
 
-	nvports = esw->total_vports + MLX5_ESW_MISS_FLOWS;
+	nvports = esw_get_offloads_ft_size(esw);
 	flow_group_in = kvzalloc(inlen, GFP_KERNEL);
 	if (!flow_group_in)
 		return -ENOMEM;
@@ -2471,6 +2501,7 @@
 	struct mlx5_eswitch *esw = master->priv.eswitch;
 	struct mlx5_flow_table_attr ft_attr = {
 		.max_fte = 1, .prio = 0, .level = 0,
+		.flags = MLX5_FLOW_TABLE_OTHER_VPORT,
 	};
 	struct mlx5_flow_namespace *egress_ns;
 	struct mlx5_flow_table *acl;
@@ -2783,17 +2814,14 @@
 	if (!MLX5_CAP_ESW_FLOWTABLE(esw->dev, flow_source))
 		return false;
 
-	if (mlx5_core_is_ecpf_esw_manager(esw->dev) ||
-	    mlx5_ecpf_vport_exists(esw->dev))
-		return false;
-
 	return true;
 }
 
 u32 mlx5_esw_match_metadata_alloc(struct mlx5_eswitch *esw)
 {
 	u32 vport_end_ida = (1 << ESW_VPORT_BITS) - 1;
-	u32 max_pf_num = (1 << ESW_PFNUM_BITS) - 1;
+	/* Reserve 0xf for internal port offload */
+	u32 max_pf_num = (1 << ESW_PFNUM_BITS) - 2;
 	u32 pf_num;
 	int id;
 
@@ -3141,12 +3169,6 @@
 	u64 mapping_id;
 	int err;
 
-	if (MLX5_CAP_ESW_FLOWTABLE_FDB(esw->dev, reformat) &&
-	    MLX5_CAP_ESW_FLOWTABLE_FDB(esw->dev, decap))
-		esw->offloads.encap = DEVLINK_ESWITCH_ENCAP_MODE_BASIC;
-	else
-		esw->offloads.encap = DEVLINK_ESWITCH_ENCAP_MODE_NONE;
-
 	mutex_init(&esw->offloads.termtbl_mutex);
 	mlx5_rdma_enable_roce(esw->dev);
 
@@ -3244,7 +3266,6 @@
 	esw_offloads_metadata_uninit(esw);
 	mlx5_rdma_disable_roce(esw->dev);
 	mutex_destroy(&esw->offloads.termtbl_mutex);
-	esw->offloads.encap = DEVLINK_ESWITCH_ENCAP_MODE_NONE;
 }
 
 static int esw_mode_from_devlink(u16 mode, u16 *mlx5_mode)
@@ -3588,7 +3609,7 @@
 	*encap = esw->offloads.encap;
 unlock:
 	up_write(&esw->mode_lock);
-	return 0;
+	return err;
 }
 
 static bool
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c
@@ -30,9 +30,9 @@
 		     sizeof(dest->vport.num), hash);
 	hash = jhash((const void *)&dest->vport.vhca_id,
 		     sizeof(dest->vport.num), hash);
-	if (dest->vport.pkt_reformat)
-		hash = jhash(dest->vport.pkt_reformat,
-			     sizeof(*dest->vport.pkt_reformat),
+	if (flow_act->pkt_reformat)
+		hash = jhash(flow_act->pkt_reformat,
+			     sizeof(*flow_act->pkt_reformat),
 			     hash);
 	return hash;
 }
@@ -53,9 +53,11 @@
 	if (ret)
 		return ret;
 
-	return dest1->vport.pkt_reformat && dest2->vport.pkt_reformat ?
-	       memcmp(dest1->vport.pkt_reformat, dest2->vport.pkt_reformat,
-		      sizeof(*dest1->vport.pkt_reformat)) : 0;
+	if (flow_act1->pkt_reformat && flow_act2->pkt_reformat)
+		return memcmp(flow_act1->pkt_reformat, flow_act2->pkt_reformat,
+			      sizeof(*flow_act1->pkt_reformat));
+
+	return !(flow_act1->pkt_reformat == flow_act2->pkt_reformat);
 }
 
 static int
@@ -219,8 +221,8 @@
 
 	if (!MLX5_CAP_ESW_FLOWTABLE_FDB(esw->dev, termination_table) ||
 	    !MLX5_CAP_ESW_FLOWTABLE_FDB(esw->dev, ignore_flow_level) ||
-	    attr->flags & MLX5_ESW_ATTR_FLAG_SLOW_PATH ||
-	    !mlx5_eswitch_offload_is_uplink_port(esw, spec))
+	    mlx5_esw_attr_flags_skip(attr->flags) ||
+	    (!mlx5_eswitch_offload_is_uplink_port(esw, spec) && !esw_attr->int_port))
 		return false;
 
 	/* push vlan on RX */
@@ -229,7 +231,8 @@
 
 	/* hairpin */
 	for (i = esw_attr->split_count; i < esw_attr->out_count; i++)
-		if (esw_attr->dests[i].rep->vport == MLX5_VPORT_UPLINK)
+		if (!esw_attr->dest_int_port && esw_attr->dests[i].rep &&
+		    esw_attr->dests[i].rep->vport == MLX5_VPORT_UPLINK)
 			return true;
 
 	return false;
@@ -307,6 +310,8 @@
 	for (curr_dest = 0; curr_dest < num_vport_dests; curr_dest++) {
 		struct mlx5_termtbl_handle *tt = attr->dests[curr_dest].termtbl;
 
+		attr->dests[curr_dest].termtbl = NULL;
+
 		/* search for the destination associated with the
 		 * current term table
 		 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c
@@ -152,6 +152,12 @@
 	return 0;
 }
 
+static u32 mlx5_cmd_stub_get_capabilities(struct mlx5_flow_root_namespace *ns,
+					  enum fs_flow_table_type ft_type)
+{
+	return 0;
+}
+
 static int mlx5_cmd_set_slave_root_fdb(struct mlx5_core_dev *master,
 				       struct mlx5_core_dev *slave,
 				       bool ft_id_valid,
@@ -185,6 +191,20 @@
 	return mlx5_cmd_exec(slave, in, sizeof(in), out, sizeof(out));
 }
 
+static int
+mlx5_cmd_stub_destroy_match_definer(struct mlx5_flow_root_namespace *ns,
+				    int definer_id)
+{
+	return 0;
+}
+
+static int
+mlx5_cmd_stub_create_match_definer(struct mlx5_flow_root_namespace *ns,
+				   u16 format_id, u32 *match_mask)
+{
+	return 0;
+}
+
 static int mlx5_cmd_update_root_ft(struct mlx5_flow_root_namespace *ns,
 				   struct mlx5_flow_table *ft, u32 underlay_qpn,
 				   bool disconnect)
@@ -437,7 +457,8 @@
 	list_for_each_entry(dst, &fte->node.children, node.list) {
 		if (dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_COUNTER)
 			continue;
-		if (dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_VPORT &&
+		if ((dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_VPORT ||
+		     dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_UPLINK) &&
 		    dst->dest_attr.vport.flags & MLX5_FLOW_DEST_VPORT_REFORMAT_ID)
 			num_encap++;
 		num_fwd_destinations++;
@@ -563,8 +584,8 @@
 			case MLX5_FLOW_DESTINATION_TYPE_FLOW_TABLE:
 				id = dst->dest_attr.ft->id;
 				break;
+			case MLX5_FLOW_DESTINATION_TYPE_UPLINK:
 			case MLX5_FLOW_DESTINATION_TYPE_VPORT:
-				id = dst->dest_attr.vport.num;
 				MLX5_SET(dest_format_struct, in_dests,
 					 destination_eswitch_owner_vhca_id_valid,
 					 !!(dst->dest_attr.vport.flags &
@@ -572,6 +593,12 @@
 				MLX5_SET(dest_format_struct, in_dests,
 					 destination_eswitch_owner_vhca_id,
 					 dst->dest_attr.vport.vhca_id);
+				if (type == MLX5_FLOW_DESTINATION_TYPE_UPLINK) {
+					/* destination_id is reserved */
+					id = 0;
+					break;
+				}
+				id = dst->dest_attr.vport.num;
 				if (extended_dest &&
 				    dst->dest_attr.vport.pkt_reformat) {
 					MLX5_SET(dest_format_struct, in_dests,
@@ -909,6 +936,51 @@
 	mlx5_cmd_exec_in(dev, dealloc_modify_header_context, in);
 }
 
+static u32 mlx5_cmd_get_capabilities(struct mlx5_flow_root_namespace *ns,
+				     enum fs_flow_table_type ft_type)
+{
+	return 0;
+}
+
+static int mlx5_cmd_destroy_match_definer(struct mlx5_flow_root_namespace *ns,
+					  int definer_id)
+{
+	u32 in[MLX5_ST_SZ_DW(general_obj_in_cmd_hdr)] = {};
+	u32 out[MLX5_ST_SZ_DW(general_obj_out_cmd_hdr)];
+
+	MLX5_SET(general_obj_in_cmd_hdr, in, opcode,
+		 MLX5_CMD_OP_DESTROY_GENERAL_OBJECT);
+	MLX5_SET(general_obj_in_cmd_hdr, in, obj_type,
+		 MLX5_OBJ_TYPE_MATCH_DEFINER);
+	MLX5_SET(general_obj_in_cmd_hdr, in, obj_id, definer_id);
+
+	return mlx5_cmd_exec(ns->dev, in, sizeof(in), out, sizeof(out));
+}
+
+static int mlx5_cmd_create_match_definer(struct mlx5_flow_root_namespace *ns,
+					 u16 format_id, u32 *match_mask)
+{
+	u32 out[MLX5_ST_SZ_DW(create_match_definer_out)] = {};
+	u32 in[MLX5_ST_SZ_DW(create_match_definer_in)] = {};
+	struct mlx5_core_dev *dev = ns->dev;
+	void *ptr;
+	int err;
+
+	MLX5_SET(create_match_definer_in, in, general_obj_in_cmd_hdr.opcode,
+		 MLX5_CMD_OP_CREATE_GENERAL_OBJECT);
+	MLX5_SET(create_match_definer_in, in, general_obj_in_cmd_hdr.obj_type,
+		 MLX5_OBJ_TYPE_MATCH_DEFINER);
+
+	ptr = MLX5_ADDR_OF(create_match_definer_in, in, obj_context);
+	MLX5_SET(match_definer, ptr, format_id, format_id);
+
+	ptr = MLX5_ADDR_OF(match_definer, ptr, match_mask);
+	memcpy(ptr, match_mask, MLX5_FLD_SZ_BYTES(match_definer, match_mask));
+
+	err = mlx5_cmd_exec_inout(dev, create_match_definer, in, out);
+	return err ? err : MLX5_GET(general_obj_out_cmd_hdr, out, obj_id);
+}
+
 static const struct mlx5_flow_cmds mlx5_flow_cmds = {
 	.create_flow_table = mlx5_cmd_create_flow_table,
 	.destroy_flow_table = mlx5_cmd_destroy_flow_table,
@@ -923,9 +995,12 @@
 	.packet_reformat_dealloc = mlx5_cmd_packet_reformat_dealloc,
 	.modify_header_alloc = mlx5_cmd_modify_header_alloc,
 	.modify_header_dealloc = mlx5_cmd_modify_header_dealloc,
+	.create_match_definer = mlx5_cmd_create_match_definer,
+	.destroy_match_definer = mlx5_cmd_destroy_match_definer,
 	.set_peer = mlx5_cmd_stub_set_peer,
 	.create_ns = mlx5_cmd_stub_create_ns,
 	.destroy_ns = mlx5_cmd_stub_destroy_ns,
+	.get_capabilities = mlx5_cmd_get_capabilities,
 };
 
 static const struct mlx5_flow_cmds mlx5_flow_cmd_stubs = {
@@ -942,9 +1017,12 @@
 	.packet_reformat_dealloc = mlx5_cmd_stub_packet_reformat_dealloc,
 	.modify_header_alloc = mlx5_cmd_stub_modify_header_alloc,
 	.modify_header_dealloc = mlx5_cmd_stub_modify_header_dealloc,
+	.create_match_definer = mlx5_cmd_stub_create_match_definer,
+	.destroy_match_definer = mlx5_cmd_stub_destroy_match_definer,
 	.set_peer = mlx5_cmd_stub_set_peer,
 	.create_ns = mlx5_cmd_stub_create_ns,
 	.destroy_ns = mlx5_cmd_stub_destroy_ns,
+	.get_capabilities = mlx5_cmd_stub_get_capabilities,
 };
 
 const struct mlx5_flow_cmds *mlx5_fs_cmd_get_fw_cmds(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.h
@@ -97,6 +97,12 @@
 
 	int (*create_ns)(struct mlx5_flow_root_namespace *ns);
 	int (*destroy_ns)(struct mlx5_flow_root_namespace *ns);
+	int (*create_match_definer)(struct mlx5_flow_root_namespace *ns,
+				    u16 format_id, u32 *match_mask);
+	int (*destroy_match_definer)(struct mlx5_flow_root_namespace *ns,
+				     int definer_id);
+	u32 (*get_capabilities)(struct mlx5_flow_root_namespace *ns,
+				enum fs_flow_table_type ft_type);
 };
 
 int mlx5_cmd_fc_alloc(struct mlx5_core_dev *dev, u32 *id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c
@@ -99,6 +99,9 @@
 #define LEFTOVERS_NUM_LEVELS 1
 #define LEFTOVERS_NUM_PRIOS 1
 
+#define RDMA_RX_COUNTERS_PRIO_NUM_LEVELS 1
+#define RDMA_TX_COUNTERS_PRIO_NUM_LEVELS 1
+
 #define BY_PASS_PRIO_NUM_LEVELS 1
 #define BY_PASS_MIN_LEVEL (ETHTOOL_MIN_LEVEL + MLX5_BY_PASS_NUM_PRIOS +\
 			   LEFTOVERS_NUM_PRIOS)
@@ -113,7 +116,7 @@
 #define KERNEL_MIN_LEVEL (KERNEL_NIC_PRIO_NUM_LEVELS + 1)
 
 #define KERNEL_NIC_TC_NUM_PRIOS  1
-#define KERNEL_NIC_TC_NUM_LEVELS 2
+#define KERNEL_NIC_TC_NUM_LEVELS 3
 
 #define ANCHOR_NUM_LEVELS 1
 #define ANCHOR_NUM_PRIOS 1
@@ -206,34 +209,63 @@
 	}
 };
 
-#define RDMA_RX_BYPASS_PRIO 0
-#define RDMA_RX_KERNEL_PRIO 1
+enum {
+	RDMA_RX_COUNTERS_PRIO,
+	RDMA_RX_BYPASS_PRIO,
+	RDMA_RX_KERNEL_PRIO,
+};
+
+#define RDMA_RX_BYPASS_MIN_LEVEL MLX5_BY_PASS_NUM_REGULAR_PRIOS
+#define RDMA_RX_KERNEL_MIN_LEVEL (RDMA_RX_BYPASS_MIN_LEVEL + 1)
+#define RDMA_RX_COUNTERS_MIN_LEVEL (RDMA_RX_KERNEL_MIN_LEVEL + 2)
+
 static struct init_tree_node rdma_rx_root_fs = {
 	.type = FS_TYPE_NAMESPACE,
-	.ar_size = 2,
+	.ar_size = 3,
 	.children = (struct init_tree_node[]) {
+		[RDMA_RX_COUNTERS_PRIO] =
+		ADD_PRIO(0, RDMA_RX_COUNTERS_MIN_LEVEL, 0,
+			 FS_CHAINING_CAPS,
+			 ADD_NS(MLX5_FLOW_TABLE_MISS_ACTION_DEF,
+				ADD_MULTIPLE_PRIO(MLX5_RDMA_RX_NUM_COUNTERS_PRIOS,
+						  RDMA_RX_COUNTERS_PRIO_NUM_LEVELS))),
 		[RDMA_RX_BYPASS_PRIO] =
-		ADD_PRIO(0, MLX5_BY_PASS_NUM_REGULAR_PRIOS, 0,
+		ADD_PRIO(0, RDMA_RX_BYPASS_MIN_LEVEL, 0,
 			 FS_CHAINING_CAPS,
 			 ADD_NS(MLX5_FLOW_TABLE_MISS_ACTION_DEF,
 				ADD_MULTIPLE_PRIO(MLX5_BY_PASS_NUM_REGULAR_PRIOS,
 						  BY_PASS_PRIO_NUM_LEVELS))),
 		[RDMA_RX_KERNEL_PRIO] =
-		ADD_PRIO(0, MLX5_BY_PASS_NUM_REGULAR_PRIOS + 1, 0,
+		ADD_PRIO(0, RDMA_RX_KERNEL_MIN_LEVEL, 0,
 			 FS_CHAINING_CAPS,
 			 ADD_NS(MLX5_FLOW_TABLE_MISS_ACTION_SWITCH_DOMAIN,
 				ADD_MULTIPLE_PRIO(1, 1))),
 	}
 };
 
+enum {
+	RDMA_TX_COUNTERS_PRIO,
+	RDMA_TX_BYPASS_PRIO,
+};
+
+#define RDMA_TX_BYPASS_MIN_LEVEL MLX5_BY_PASS_NUM_PRIOS
+#define RDMA_TX_COUNTERS_MIN_LEVEL (RDMA_TX_BYPASS_MIN_LEVEL + 1)
+
 static struct init_tree_node rdma_tx_root_fs = {
 	.type = FS_TYPE_NAMESPACE,
-	.ar_size = 1,
+	.ar_size = 2,
 	.children = (struct init_tree_node[]) {
-		ADD_PRIO(0, MLX5_BY_PASS_NUM_PRIOS, 0,
+		[RDMA_TX_COUNTERS_PRIO] =
+		ADD_PRIO(0, RDMA_TX_COUNTERS_MIN_LEVEL, 0,
+			 FS_CHAINING_CAPS,
+			 ADD_NS(MLX5_FLOW_TABLE_MISS_ACTION_DEF,
+				ADD_MULTIPLE_PRIO(MLX5_RDMA_TX_NUM_COUNTERS_PRIOS,
+						  RDMA_TX_COUNTERS_PRIO_NUM_LEVELS))),
+		[RDMA_TX_BYPASS_PRIO] =
+		ADD_PRIO(0, RDMA_TX_BYPASS_MIN_LEVEL, 0,
 			 FS_CHAINING_CAPS_RDMA_TX,
 			 ADD_NS(MLX5_FLOW_TABLE_MISS_ACTION_DEF,
-				ADD_MULTIPLE_PRIO(MLX5_BY_PASS_NUM_PRIOS,
+				ADD_MULTIPLE_PRIO(RDMA_TX_BYPASS_MIN_LEVEL,
 						  BY_PASS_PRIO_NUM_LEVELS))),
 	}
 };
@@ -526,8 +558,8 @@
 		mutex_unlock(&rule->dest_attr.ft->lock);
 	}
 
-	if (rule->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_COUNTER  &&
-	    --fte->dests_size) {
+	if (rule->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_COUNTER) {
+		--fte->dests_size;
 		fte->modify_mask |=
 			BIT(MLX5_SET_FTE_MODIFY_ENABLE_MASK_ACTION) |
 			BIT(MLX5_SET_FTE_MODIFY_ENABLE_MASK_FLOW_COUNTERS);
@@ -535,15 +567,15 @@
 		goto out;
 	}
 
-	if (rule->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_PORT &&
-	    --fte->dests_size) {
+	if (rule->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_PORT) {
+		--fte->dests_size;
 		fte->modify_mask |= BIT(MLX5_SET_FTE_MODIFY_ENABLE_MASK_ACTION);
 		fte->action.action &= ~MLX5_FLOW_CONTEXT_ACTION_ALLOW;
 		goto out;
 	}
 
-	if ((fte->action.action & MLX5_FLOW_CONTEXT_ACTION_FWD_DEST) &&
-	    --fte->dests_size) {
+	if (fte->action.action & MLX5_FLOW_CONTEXT_ACTION_FWD_DEST) {
+		--fte->dests_size;
 		fte->modify_mask |=
 			BIT(MLX5_SET_FTE_MODIFY_ENABLE_MASK_DESTINATION_LIST);
 	}
@@ -802,7 +834,7 @@
 	struct fs_node *iter = list_entry(start, struct fs_node, list);
 	struct mlx5_flow_table *ft = NULL;
 
-	if (!root || root->type == FS_TYPE_PRIO_CHAINS)
+	if (!root)
 		return NULL;
 
 	list_for_each_advance_continue(iter, &root->children, reverse) {
@@ -818,20 +850,42 @@
 	return ft;
 }
 
-/* If reverse is false then return the first flow table in next priority of
- * prio in the tree, else return the last flow table in the previous priority
- * of prio in the tree.
+static struct fs_node *find_prio_chains_parent(struct fs_node *parent,
+					       struct fs_node **child)
+{
+	struct fs_node *node = NULL;
+
+	while (parent && parent->type != FS_TYPE_PRIO_CHAINS) {
+		node = parent;
+		parent = parent->parent;
+	}
+
+	if (child)
+		*child = node;
+
+	return parent;
+}
+
+/* If reverse is false then return the first flow table next to the passed node
+ * in the tree, else return the last flow table before the node in the tree.
+ * If skip is true, skip the flow tables in the same prio_chains prio.
  */
-static struct mlx5_flow_table *find_closest_ft(struct fs_prio *prio, bool reverse)
+static struct mlx5_flow_table *find_closest_ft(struct fs_node *node, bool reverse,
+					       bool skip)
 {
+	struct fs_node *prio_chains_parent = NULL;
 	struct mlx5_flow_table *ft = NULL;
 	struct fs_node *curr_node;
 	struct fs_node *parent;
 
-	parent = prio->node.parent;
-	curr_node = &prio->node;
+	if (skip)
+		prio_chains_parent = find_prio_chains_parent(node, NULL);
+	parent = node->parent;
+	curr_node = node;
 	while (!ft && parent) {
-		ft = find_closest_ft_recursive(parent, &curr_node->list, reverse);
+		if (parent != prio_chains_parent)
+			ft = find_closest_ft_recursive(parent, &curr_node->list,
+						       reverse);
 		curr_node = parent;
 		parent = curr_node->parent;
 	}
@@ -839,15 +893,15 @@
 }
 
 /* Assuming all the tree is locked by mutex chain lock */
-static struct mlx5_flow_table *find_next_chained_ft(struct fs_prio *prio)
+static struct mlx5_flow_table *find_next_chained_ft(struct fs_node *node)
 {
-	return find_closest_ft(prio, false);
+	return find_closest_ft(node, false, true);
 }
 
 /* Assuming all the tree is locked by mutex chain lock */
-static struct mlx5_flow_table *find_prev_chained_ft(struct fs_prio *prio)
+static struct mlx5_flow_table *find_prev_chained_ft(struct fs_node *node)
 {
-	return find_closest_ft(prio, true);
+	return find_closest_ft(node, true, true);
 }
 
 static struct mlx5_flow_table *find_next_fwd_ft(struct mlx5_flow_table *ft,
@@ -859,7 +913,7 @@
 	next_ns = flow_act->action & MLX5_FLOW_CONTEXT_ACTION_FWD_NEXT_NS;
 	fs_get_obj(prio, next_ns ? ft->ns->node.parent : ft->node.parent);
 
-	return find_next_chained_ft(prio);
+	return find_next_chained_ft(&prio->node);
 }
 
 static int connect_fts_in_prio(struct mlx5_core_dev *dev,
@@ -883,21 +937,55 @@
 	return 0;
 }
 
+static struct mlx5_flow_table *find_closet_ft_prio_chains(struct fs_node *node,
+							  struct fs_node *parent,
+							  struct fs_node **child,
+							  bool reverse)
+{
+	struct mlx5_flow_table *ft;
+
+	ft = find_closest_ft(node, reverse, false);
+
+	if (ft && parent == find_prio_chains_parent(&ft->node, child))
+		return ft;
+
+	return NULL;
+}
+
 /* Connect flow tables from previous priority of prio to ft */
 static int connect_prev_fts(struct mlx5_core_dev *dev,
 			    struct mlx5_flow_table *ft,
 			    struct fs_prio *prio)
 {
+	struct fs_node *prio_parent, *parent = NULL, *child, *node;
 	struct mlx5_flow_table *prev_ft;
+	int err = 0;
+
+	prio_parent = find_prio_chains_parent(&prio->node, &child);
 
-	prev_ft = find_prev_chained_ft(prio);
-	if (prev_ft) {
+	/* return directly if not under the first sub ns of prio_chains prio */
+	if (prio_parent && !list_is_first(&child->list, &prio_parent->children))
+		return 0;
+
+	prev_ft = find_prev_chained_ft(&prio->node);
+	while (prev_ft) {
 		struct fs_prio *prev_prio;
 
 		fs_get_obj(prev_prio, prev_ft->node.parent);
-		return connect_fts_in_prio(dev, prev_prio, ft);
+		err = connect_fts_in_prio(dev, prev_prio, ft);
+		if (err)
+			break;
+
+		if (!parent) {
+			parent = find_prio_chains_parent(&prev_prio->node, &child);
+			if (!parent)
+				break;
+		}
+
+		node = child;
+		prev_ft = find_closet_ft_prio_chains(node, parent, &child, true);
 	}
-	return 0;
+	return err;
 }
 
 static int update_root_ft_create(struct mlx5_flow_table *ft, struct fs_prio
@@ -1036,7 +1124,7 @@
 		if (err)
 			return err;
 
-		next_ft = first_ft ? first_ft : find_next_chained_ft(prio);
+		next_ft = first_ft ? first_ft : find_next_chained_ft(&prio->node);
 		err = connect_fwd_rules(dev, ft, next_ft);
 		if (err)
 			return err;
@@ -1111,7 +1199,7 @@
 
 	tree_init_node(&ft->node, del_hw_flow_table, del_sw_flow_table);
 	next_ft = unmanaged ? ft_attr->next_ft :
-			      find_next_chained_ft(fs_prio);
+			      find_next_chained_ft(&fs_prio->node);
 	ft->def_miss_action = ns->def_miss_action;
 	ft->ns = ns;
 	err = root->cmds->create_flow_table(root, ft, ft_attr->max_fte, next_ft);
@@ -1493,7 +1581,8 @@
 				struct mlx5_flow_destination *d2)
 {
 	if (d1->type == d2->type) {
-		if ((d1->type == MLX5_FLOW_DESTINATION_TYPE_VPORT &&
+		if (((d1->type == MLX5_FLOW_DESTINATION_TYPE_VPORT ||
+		      d1->type == MLX5_FLOW_DESTINATION_TYPE_UPLINK) &&
 		     d1->vport.num == d2->vport.num &&
 		     d1->vport.flags == d2->vport.flags &&
 		     ((d1->vport.flags & MLX5_FLOW_DEST_VPORT_VHCA_ID) ?
@@ -1527,9 +1616,22 @@
 	return NULL;
 }
 
-static bool check_conflicting_actions(u32 action1, u32 action2)
+static bool check_conflicting_actions_vlan(const struct mlx5_fs_vlan *vlan0,
+					   const struct mlx5_fs_vlan *vlan1)
 {
-	u32 xored_actions = action1 ^ action2;
+	return vlan0->ethtype != vlan1->ethtype ||
+	       vlan0->vid != vlan1->vid ||
+	       vlan0->prio != vlan1->prio;
+}
+
+static bool check_conflicting_actions(const struct mlx5_flow_act *act1,
+				      const struct mlx5_flow_act *act2)
+{
+	u32 action1 = act1->action;
+	u32 action2 = act2->action;
+	u32 xored_actions;
+
+	xored_actions = action1 ^ action2;
 
 	/* if one rule only wants to count, it's ok */
 	if (action1 == MLX5_FLOW_CONTEXT_ACTION_COUNT ||
@@ -1546,6 +1648,22 @@
 			     MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH_2))
 		return true;
 
+	if (action1 & MLX5_FLOW_CONTEXT_ACTION_PACKET_REFORMAT &&
+	    act1->pkt_reformat != act2->pkt_reformat)
+		return true;
+
+	if (action1 & MLX5_FLOW_CONTEXT_ACTION_MOD_HDR &&
+	    act1->modify_hdr != act2->modify_hdr)
+		return true;
+
+	if (action1 & MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH &&
+	    check_conflicting_actions_vlan(&act1->vlan[0], &act2->vlan[0]))
+		return true;
+
+	if (action1 & MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH_2 &&
+	    check_conflicting_actions_vlan(&act1->vlan[1], &act2->vlan[1]))
+		return true;
+
 	return false;
 }
 
@@ -1553,7 +1671,7 @@
 				  const struct mlx5_flow_context *flow_context,
 				  const struct mlx5_flow_act *flow_act)
 {
-	if (check_conflicting_actions(flow_act->action, fte->action.action)) {
+	if (check_conflicting_actions(flow_act, &fte->action)) {
 		mlx5_core_warn(get_dev(&fte->node),
 			       "Found two FTEs with conflicting actions\n");
 		return -EEXIST;
@@ -1597,8 +1715,9 @@
 	}
 	trace_mlx5_fs_set_fte(fte, false);
 
+	/* Link newly added rules into the tree. */
 	for (i = 0; i < handle->num_rules; i++) {
-		if (refcount_read(&handle->rule[i]->node.refcount) == 1) {
+		if (!handle->rule[i]->node.parent) {
 			tree_add_node(&handle->rule[i]->node, &fte->node);
 			trace_mlx5_fs_add_rule(handle->rule[i]);
 		}
@@ -1720,13 +1839,22 @@
 		fte_tmp = NULL;
 		goto out;
 	}
+
+	nested_down_write_ref_node(&fte_tmp->node, FS_LOCK_CHILD);
+
 	if (!fte_tmp->node.active) {
+		up_write_ref_node(&fte_tmp->node, false);
+
+		if (take_write)
+			up_write_ref_node(&g->node, false);
+		else
+			up_read_ref_node(&g->node);
+
 		tree_put_node(&fte_tmp->node, false);
-		fte_tmp = NULL;
-		goto out;
+
+		return NULL;
 	}
 
-	nested_down_write_ref_node(&fte_tmp->node, FS_LOCK_CHILD);
 out:
 	if (take_write)
 		up_write_ref_node(&g->node, false);
@@ -2031,16 +2159,18 @@
 	down_write_ref_node(&fte->node, false);
 	for (i = handle->num_rules - 1; i >= 0; i--)
 		tree_remove_node(&handle->rule[i]->node, true);
-	if (fte->dests_size) {
-		if (fte->modify_mask)
-			modify_fte(fte);
-		up_write_ref_node(&fte->node, false);
-	} else if (list_empty(&fte->node.children)) {
+	if (list_empty(&fte->node.children)) {
 		del_hw_fte(&fte->node);
 		/* Avoid double call to del_hw_fte */
 		fte->node.del_hw_func = NULL;
 		up_write_ref_node(&fte->node, false);
 		tree_put_node(&fte->node, false);
+	} else if (fte->dests_size) {
+		if (fte->modify_mask)
+			modify_fte(fte);
+		up_write_ref_node(&fte->node, false);
+	} else {
+		up_write_ref_node(&fte->node, false);
 	}
 	kfree(handle);
 }
@@ -2049,13 +2179,20 @@
 /* Assuming prio->node.children(flow tables) is sorted by level */
 static struct mlx5_flow_table *find_next_ft(struct mlx5_flow_table *ft)
 {
+	struct fs_node *prio_parent, *child;
 	struct fs_prio *prio;
 
 	fs_get_obj(prio, ft->node.parent);
 
 	if (!list_is_last(&ft->node.list, &prio->node.children))
 		return list_next_entry(ft, node.list);
-	return find_next_chained_ft(prio);
+
+	prio_parent = find_prio_chains_parent(&prio->node, &child);
+
+	if (prio_parent && list_is_first(&child->list, &prio_parent->children))
+		return find_closest_ft(&prio->node, false, false);
+
+	return find_next_chained_ft(&prio->node);
 }
 
 static int update_root_ft_destroy(struct mlx5_flow_table *ft)
@@ -2174,6 +2311,22 @@
 }
 EXPORT_SYMBOL(mlx5_get_fdb_sub_ns);
 
+static bool is_nic_rx_ns(enum mlx5_flow_namespace_type type)
+{
+	switch (type) {
+	case MLX5_FLOW_NAMESPACE_BYPASS:
+	case MLX5_FLOW_NAMESPACE_LAG:
+	case MLX5_FLOW_NAMESPACE_OFFLOADS:
+	case MLX5_FLOW_NAMESPACE_ETHTOOL:
+	case MLX5_FLOW_NAMESPACE_KERNEL:
+	case MLX5_FLOW_NAMESPACE_LEFTOVERS:
+	case MLX5_FLOW_NAMESPACE_ANCHOR:
+		return true;
+	default:
+		return false;
+	}
+}
+
 struct mlx5_flow_namespace *mlx5_get_flow_namespace(struct mlx5_core_dev *dev,
 						    enum mlx5_flow_namespace_type type)
 {
@@ -2199,25 +2352,36 @@
 		if (steering->sniffer_tx_root_ns)
 			return &steering->sniffer_tx_root_ns->ns;
 		return NULL;
-	default:
-		break;
-	}
-
-	if (type == MLX5_FLOW_NAMESPACE_EGRESS ||
-	    type == MLX5_FLOW_NAMESPACE_EGRESS_KERNEL) {
+	case MLX5_FLOW_NAMESPACE_EGRESS:
+	case MLX5_FLOW_NAMESPACE_EGRESS_KERNEL:
 		root_ns = steering->egress_root_ns;
 		prio = type - MLX5_FLOW_NAMESPACE_EGRESS;
-	} else if (type == MLX5_FLOW_NAMESPACE_RDMA_RX) {
+		break;
+	case MLX5_FLOW_NAMESPACE_RDMA_RX:
 		root_ns = steering->rdma_rx_root_ns;
 		prio = RDMA_RX_BYPASS_PRIO;
-	} else if (type == MLX5_FLOW_NAMESPACE_RDMA_RX_KERNEL) {
+		break;
+	case MLX5_FLOW_NAMESPACE_RDMA_RX_KERNEL:
 		root_ns = steering->rdma_rx_root_ns;
 		prio = RDMA_RX_KERNEL_PRIO;
-	} else if (type == MLX5_FLOW_NAMESPACE_RDMA_TX) {
+		break;
+	case MLX5_FLOW_NAMESPACE_RDMA_TX:
 		root_ns = steering->rdma_tx_root_ns;
-	} else { /* Must be NIC RX */
+		prio = RDMA_TX_BYPASS_PRIO;
+		break;
+	case MLX5_FLOW_NAMESPACE_RDMA_RX_COUNTERS:
+		root_ns = steering->rdma_rx_root_ns;
+		prio = RDMA_RX_COUNTERS_PRIO;
+		break;
+	case MLX5_FLOW_NAMESPACE_RDMA_TX_COUNTERS:
+		root_ns = steering->rdma_tx_root_ns;
+		prio = RDMA_TX_COUNTERS_PRIO;
+		break;
+	default: /* Must be NIC RX */
+		WARN_ON(!is_nic_rx_ns(type));
 		root_ns = steering->root_ns;
 		prio = type;
+		break;
 	}
 
 	if (!root_ns)
@@ -2937,6 +3101,22 @@
 	steering->esw_ingress_root_ns = NULL;
 }
 
+u32 mlx5_fs_get_capabilities(struct mlx5_core_dev *dev, enum mlx5_flow_namespace_type type)
+{
+	struct mlx5_flow_root_namespace *root;
+	struct mlx5_flow_namespace *ns;
+
+	ns = mlx5_get_flow_namespace(dev, type);
+	if (!ns)
+		return 0;
+
+	root = find_root(&ns->node);
+	if (!root)
+		return 0;
+
+	return root->cmds->get_capabilities(root, root->table_type);
+}
+
 static int init_egress_root_ns(struct mlx5_flow_steering *steering)
 {
 	int err;
@@ -2980,6 +3160,11 @@
 	steering->dev = dev;
 	dev->priv.steering = steering;
 
+	if (mlx5_fs_dr_is_supported(dev))
+		steering->mode = MLX5_FLOW_STEERING_MODE_SMFS;
+	else
+		steering->mode = MLX5_FLOW_STEERING_MODE_DMFS;
+
 	steering->fgs_cache = kmem_cache_create("mlx5_fs_fgs",
 						sizeof(struct mlx5_flow_group), 0,
 						0, NULL);
@@ -3224,6 +3409,52 @@
 }
 EXPORT_SYMBOL(mlx5_packet_reformat_dealloc);
 
+int mlx5_get_match_definer_id(struct mlx5_flow_definer *definer)
+{
+	return definer->id;
+}
+
+struct mlx5_flow_definer *
+mlx5_create_match_definer(struct mlx5_core_dev *dev,
+			  enum mlx5_flow_namespace_type ns_type, u16 format_id,
+			  u32 *match_mask)
+{
+	struct mlx5_flow_root_namespace *root;
+	struct mlx5_flow_definer *definer;
+	int id;
+
+	root = get_root_namespace(dev, ns_type);
+	if (!root)
+		return ERR_PTR(-EOPNOTSUPP);
+
+	definer = kzalloc(sizeof(*definer), GFP_KERNEL);
+	if (!definer)
+		return ERR_PTR(-ENOMEM);
+
+	definer->ns_type = ns_type;
+	id = root->cmds->create_match_definer(root, format_id, match_mask);
+	if (id < 0) {
+		mlx5_core_warn(root->dev, "Failed to create match definer (%d)\n", id);
+		kfree(definer);
+		return ERR_PTR(id);
+	}
+	definer->id = id;
+	return definer;
+}
+
+void mlx5_destroy_match_definer(struct mlx5_core_dev *dev,
+				struct mlx5_flow_definer *definer)
+{
+	struct mlx5_flow_root_namespace *root;
+
+	root = get_root_namespace(dev, definer->ns_type);
+	if (WARN_ON(!root))
+		return;
+
+	root->cmds->destroy_match_definer(root, definer->id);
+	kfree(definer);
+}
+
 int mlx5_flow_namespace_set_peer(struct mlx5_flow_root_namespace *ns,
 				 struct mlx5_flow_root_namespace *peer_ns)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/fs_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/fs_core.h
@@ -49,6 +49,11 @@
 #define FDB_TC_MAX_PRIO 16
 #define FDB_TC_LEVELS_PER_PRIO 2
 
+struct mlx5_flow_definer {
+	enum mlx5_flow_namespace_type ns_type;
+	u32 id;
+};
+
 struct mlx5_modify_hdr {
 	enum mlx5_flow_namespace_type ns_type;
 	union {
@@ -114,6 +119,11 @@
 	MLX5_FLOW_STEERING_MODE_SMFS
 };
 
+enum mlx5_flow_steering_capabilty {
+	MLX5_FLOW_STEERING_CAP_VLAN_PUSH_ON_RX = 1UL << 0,
+	MLX5_FLOW_STEERING_CAP_VLAN_POP_ON_TX = 1UL << 1,
+};
+
 struct mlx5_flow_steering {
 	struct mlx5_core_dev *dev;
 	enum   mlx5_flow_steering_mode	mode;
@@ -196,7 +206,7 @@
 	u32 qpn;
 };
 
-#define MLX5_FTE_MATCH_PARAM_RESERVED	reserved_at_c00
+#define MLX5_FTE_MATCH_PARAM_RESERVED	reserved_at_e00
 /* Calculate the fte_match_param length and without the reserved length.
  * Make sure the reserved field is the last.
  */
@@ -294,6 +304,8 @@
 int mlx5_fs_ingress_acls_init(struct mlx5_core_dev *dev, int total_vports);
 void mlx5_fs_ingress_acls_cleanup(struct mlx5_core_dev *dev);
 
+u32 mlx5_fs_get_capabilities(struct mlx5_core_dev *dev, enum mlx5_flow_namespace_type type);
+
 struct mlx5_flow_root_namespace *find_root(struct fs_node *node);
 
 #define fs_get_obj(v, _node)  {v = container_of((_node), typeof(*v), node); }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c
@@ -111,6 +111,28 @@
 	}
 }
 
+static void mlx5_stop_sync_reset_poll(struct mlx5_core_dev *dev)
+{
+	struct mlx5_fw_reset *fw_reset = dev->priv.fw_reset;
+
+	del_timer_sync(&fw_reset->timer);
+}
+
+static int mlx5_sync_reset_clear_reset_requested(struct mlx5_core_dev *dev, bool poll_health)
+{
+	struct mlx5_fw_reset *fw_reset = dev->priv.fw_reset;
+
+	if (!test_and_clear_bit(MLX5_FW_RESET_FLAGS_RESET_REQUESTED, &fw_reset->reset_flags)) {
+		mlx5_core_warn(dev, "Reset request was already cleared\n");
+		return -EALREADY;
+	}
+
+	mlx5_stop_sync_reset_poll(dev);
+	if (poll_health)
+		mlx5_start_health_poll(dev);
+	return 0;
+}
+
 static void mlx5_sync_reset_reload_work(struct work_struct *work)
 {
 	struct mlx5_fw_reset *fw_reset = container_of(work, struct mlx5_fw_reset,
@@ -118,6 +140,7 @@
 	struct mlx5_core_dev *dev = fw_reset->dev;
 	int err;
 
+	mlx5_sync_reset_clear_reset_requested(dev, false);
 	mlx5_enter_error_state(dev, true);
 	mlx5_unload_one(dev);
 	err = mlx5_health_wait_pci_up(dev);
@@ -127,23 +150,6 @@
 	mlx5_fw_reset_complete_reload(dev);
 }
 
-static void mlx5_stop_sync_reset_poll(struct mlx5_core_dev *dev)
-{
-	struct mlx5_fw_reset *fw_reset = dev->priv.fw_reset;
-
-	del_timer(&fw_reset->timer);
-}
-
-static void mlx5_sync_reset_clear_reset_requested(struct mlx5_core_dev *dev, bool poll_health)
-{
-	struct mlx5_fw_reset *fw_reset = dev->priv.fw_reset;
-
-	mlx5_stop_sync_reset_poll(dev);
-	clear_bit(MLX5_FW_RESET_FLAGS_RESET_REQUESTED, &fw_reset->reset_flags);
-	if (poll_health)
-		mlx5_start_health_poll(dev);
-}
-
 #define MLX5_RESET_POLL_INTERVAL	(HZ / 10)
 static void poll_sync_reset(struct timer_list *t)
 {
@@ -158,7 +164,6 @@
 
 	if (fatal_error) {
 		mlx5_core_warn(dev, "Got Device Reset\n");
-		mlx5_sync_reset_clear_reset_requested(dev, false);
 		queue_work(fw_reset->wq, &fw_reset->reset_reload_work);
 		return;
 	}
@@ -185,13 +190,17 @@
 	return mlx5_reg_mfrl_set(dev, MLX5_MFRL_REG_RESET_LEVEL3, 0, 2, false);
 }
 
-static void mlx5_sync_reset_set_reset_requested(struct mlx5_core_dev *dev)
+static int mlx5_sync_reset_set_reset_requested(struct mlx5_core_dev *dev)
 {
 	struct mlx5_fw_reset *fw_reset = dev->priv.fw_reset;
 
+	if (test_and_set_bit(MLX5_FW_RESET_FLAGS_RESET_REQUESTED, &fw_reset->reset_flags)) {
+		mlx5_core_warn(dev, "Reset request was already set\n");
+		return -EALREADY;
+	}
 	mlx5_stop_health_poll(dev, true);
-	set_bit(MLX5_FW_RESET_FLAGS_RESET_REQUESTED, &fw_reset->reset_flags);
 	mlx5_start_sync_reset_poll(dev);
+	return 0;
 }
 
 static void mlx5_fw_live_patch_event(struct work_struct *work)
@@ -220,7 +229,9 @@
 			       err ? "Failed" : "Sent");
 		return;
 	}
-	mlx5_sync_reset_set_reset_requested(dev);
+	if (mlx5_sync_reset_set_reset_requested(dev))
+		return;
+
 	err = mlx5_fw_reset_set_reset_sync_ack(dev);
 	if (err)
 		mlx5_core_warn(dev, "PCI Sync FW Update Reset Ack Failed. Error code: %d\n", err);
@@ -263,16 +274,11 @@
 		pci_cfg_access_lock(sdev);
 	}
 	/* PCI link toggle */
-	err = pci_read_config_word(bridge, cap + PCI_EXP_LNKCTL, &reg16);
-	if (err)
-		return err;
-	reg16 |= PCI_EXP_LNKCTL_LD;
-	err = pci_write_config_word(bridge, cap + PCI_EXP_LNKCTL, reg16);
+	err = pcie_capability_set_word(bridge, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_LD);
 	if (err)
 		return err;
 	msleep(500);
-	reg16 &= ~PCI_EXP_LNKCTL_LD;
-	err = pci_write_config_word(bridge, cap + PCI_EXP_LNKCTL, reg16);
+	err = pcie_capability_clear_word(bridge, PCI_EXP_LNKCTL, PCI_EXP_LNKCTL_LD);
 	if (err)
 		return err;
 
@@ -320,7 +326,8 @@
 	struct mlx5_core_dev *dev = fw_reset->dev;
 	int err;
 
-	mlx5_sync_reset_clear_reset_requested(dev, false);
+	if (mlx5_sync_reset_clear_reset_requested(dev, false))
+		return;
 
 	mlx5_core_warn(dev, "Sync Reset now. Device is going to reset.\n");
 
@@ -349,10 +356,8 @@
 						      reset_abort_work);
 	struct mlx5_core_dev *dev = fw_reset->dev;
 
-	if (!test_bit(MLX5_FW_RESET_FLAGS_RESET_REQUESTED, &fw_reset->reset_flags))
+	if (mlx5_sync_reset_clear_reset_requested(dev, true))
 		return;
-
-	mlx5_sync_reset_clear_reset_requested(dev, true);
 	mlx5_core_warn(dev, "PCI Sync FW Update Reset Aborted.\n");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/health.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/health.c
@@ -614,6 +614,13 @@
 	priv = container_of(health, struct mlx5_priv, health);
 	dev = container_of(priv, struct mlx5_core_dev, priv);
 
+	mutex_lock(&dev->intf_state_mutex);
+	if (test_bit(MLX5_DROP_NEW_HEALTH_WORK, &health->flags)) {
+		mlx5_core_err(dev, "health works are not permitted at this stage\n");
+		mutex_unlock(&dev->intf_state_mutex);
+		return;
+	}
+	mutex_unlock(&dev->intf_state_mutex);
 	enter_error_state(dev, false);
 	if (IS_ERR_OR_NULL(health->fw_fatal_reporter)) {
 		if (mlx5_health_try_recover(dev))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
@@ -172,16 +172,16 @@
 	}
 }
 
-static int mlx5i_get_speed_settings(u16 ib_link_width_oper, u16 ib_proto_oper)
+static u32 mlx5i_get_speed_settings(u16 ib_link_width_oper, u16 ib_proto_oper)
 {
 	int rate, width;
 
 	rate = mlx5_ptys_rate_enum_to_int(ib_proto_oper);
 	if (rate < 0)
-		return -EINVAL;
+		return SPEED_UNKNOWN;
 	width = mlx5_ptys_width_enum_to_int(ib_link_width_oper);
 	if (width < 0)
-		return -EINVAL;
+		return SPEED_UNKNOWN;
 
 	return rate * width;
 }
@@ -204,16 +204,13 @@
 	ethtool_link_ksettings_zero_link_mode(link_ksettings, advertising);
 
 	speed = mlx5i_get_speed_settings(ib_link_width_oper, ib_proto_oper);
-	if (speed < 0)
-		return -EINVAL;
+	link_ksettings->base.speed = speed;
+	link_ksettings->base.duplex = speed == SPEED_UNKNOWN ? DUPLEX_UNKNOWN : DUPLEX_FULL;
 
-	link_ksettings->base.duplex = DUPLEX_FULL;
 	link_ksettings->base.port = PORT_OTHER;
 
 	link_ksettings->base.autoneg = AUTONEG_DISABLE;
 
-	link_ksettings->base.speed = speed;
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ipoib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ipoib.c
@@ -67,9 +67,13 @@
 		MLX5E_PARAMS_MINIMUM_LOG_RQ_SIZE :
 		MLX5I_PARAMS_DEFAULT_LOG_RQ_SIZE;
 
-	params->lro_en = false;
+	params->packet_merge.type = MLX5E_PACKET_MERGE_NONE;
 	params->hard_mtu = MLX5_IB_GRH_BYTES + MLX5_IPOIB_HARD_LEN;
 	params->tunneled_offload_en = false;
+
+	/* CQE compression is not supported for IPoIB */
+	params->rx_cqe_compress_def = false;
+	MLX5E_SET_PFLAG(params, MLX5E_PFLAG_RX_CQE_COMPRESS, params->rx_cqe_compress_def);
 }
 
 /* Called directly after IPoIB netdevice was created to initialize SW structs */
@@ -219,7 +223,7 @@
 
 int mlx5i_create_underlay_qp(struct mlx5e_priv *priv)
 {
-	unsigned char *dev_addr = priv->netdev->dev_addr;
+	const unsigned char *dev_addr = priv->netdev->dev_addr;
 	u32 out[MLX5_ST_SZ_DW(create_qp_out)] = {};
 	u32 in[MLX5_ST_SZ_DW(create_qp_in)] = {};
 	struct mlx5i_priv *ipriv = priv->ppriv;
@@ -353,7 +357,6 @@
 static int mlx5i_init_rx(struct mlx5e_priv *priv)
 {
 	struct mlx5_core_dev *mdev = priv->mdev;
-	struct mlx5e_lro_param lro_param;
 	int err;
 
 	priv->rx_res = mlx5e_rx_res_alloc();
@@ -368,9 +371,9 @@
 		goto err_destroy_q_counters;
 	}
 
-	lro_param = mlx5e_get_lro_param(&priv->channels.params);
 	err = mlx5e_rx_res_init(priv->rx_res, priv->mdev, 0,
-				priv->max_nch, priv->drop_rq.rqn, &lro_param,
+				priv->max_nch, priv->drop_rq.rqn,
+				&priv->channels.params.packet_merge,
 				priv->channels.params.num_channels);
 	if (err)
 		goto err_close_drop_rq;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lag.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lag.c
@@ -435,7 +435,7 @@
 {
 	struct mlx5_core_dev *dev0 = ldev->pf[MLX5_LAG_P1].dev;
 	struct mlx5_core_dev *dev1 = ldev->pf[MLX5_LAG_P2].dev;
-	struct lag_tracker tracker;
+	struct lag_tracker tracker = { };
 	bool do_bond, roce_lag;
 	int err;
 
@@ -565,6 +565,7 @@
 	bool is_bonded, is_in_lag, mode_supported;
 	int bond_status = 0;
 	int num_slaves = 0;
+	int changed = 0;
 	int idx;
 
 	if (!netif_is_lag_master(upper))
@@ -601,27 +602,27 @@
 	 */
 	is_in_lag = num_slaves == MLX5_MAX_PORTS && bond_status == 0x3;
 
-	if (!mlx5_lag_is_ready(ldev) && is_in_lag) {
-		NL_SET_ERR_MSG_MOD(info->info.extack,
-				   "Can't activate LAG offload, PF is configured with more than 64 VFs");
-		return 0;
-	}
-
 	/* Lag mode must be activebackup or hash. */
 	mode_supported = tracker->tx_type == NETDEV_LAG_TX_TYPE_ACTIVEBACKUP ||
 			 tracker->tx_type == NETDEV_LAG_TX_TYPE_HASH;
 
-	if (is_in_lag && !mode_supported)
-		NL_SET_ERR_MSG_MOD(info->info.extack,
-				   "Can't activate LAG offload, TX type isn't supported");
-
 	is_bonded = is_in_lag && mode_supported;
 	if (tracker->is_bonded != is_bonded) {
 		tracker->is_bonded = is_bonded;
-		return 1;
+		changed = 1;
 	}
 
-	return 0;
+	if (!is_in_lag)
+		return changed;
+
+	if (!mlx5_lag_is_ready(ldev))
+		NL_SET_ERR_MSG_MOD(info->info.extack,
+				   "Can't activate LAG offload, PF is configured with more than 64 VFs");
+	else if (!mode_supported)
+		NL_SET_ERR_MSG_MOD(info->info.extack,
+				   "Can't activate LAG offload, TX type isn't supported");
+
+	return changed;
 }
 
 static int mlx5_handle_changelowerstate_event(struct mlx5_lag *ldev,
@@ -664,9 +665,6 @@
 
 	ldev    = container_of(this, struct mlx5_lag, nb);
 
-	if (!mlx5_lag_is_ready(ldev) && event == NETDEV_CHANGELOWERSTATE)
-		return NOTIFY_DONE;
-
 	tracker = ldev->tracker;
 
 	switch (event) {
@@ -693,30 +691,32 @@
 				 struct net_device *netdev)
 {
 	unsigned int fn = PCI_FUNC(dev->pdev->devfn);
+	unsigned long flags;
 
 	if (fn >= MLX5_MAX_PORTS)
 		return;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev->pf[fn].netdev = netdev;
 	ldev->tracker.netdev_state[fn].link_up = 0;
 	ldev->tracker.netdev_state[fn].tx_enabled = 0;
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 }
 
 static void mlx5_ldev_remove_netdev(struct mlx5_lag *ldev,
 				    struct net_device *netdev)
 {
+	unsigned long flags;
 	int i;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	for (i = 0; i < MLX5_MAX_PORTS; i++) {
 		if (ldev->pf[i].netdev == netdev) {
 			ldev->pf[i].netdev = NULL;
 			break;
 		}
 	}
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 }
 
 static void mlx5_ldev_add_mdev(struct mlx5_lag *ldev,
@@ -754,12 +754,7 @@
 	struct mlx5_lag *ldev = NULL;
 	struct mlx5_core_dev *tmp_dev;
 
-	if (!MLX5_CAP_GEN(dev, vport_group_manager) ||
-	    !MLX5_CAP_GEN(dev, lag_master) ||
-	    MLX5_CAP_GEN(dev, num_lag_ports) != MLX5_MAX_PORTS)
-		return 0;
-
-	tmp_dev = mlx5_get_next_phys_dev(dev);
+	tmp_dev = mlx5_get_next_phys_dev_lag(dev);
 	if (tmp_dev)
 		ldev = tmp_dev->priv.lag;
 
@@ -804,6 +799,11 @@
 {
 	int err;
 
+	if (!MLX5_CAP_GEN(dev, vport_group_manager) ||
+	    !MLX5_CAP_GEN(dev, lag_master) ||
+	    MLX5_CAP_GEN(dev, num_lag_ports) != MLX5_MAX_PORTS)
+		return;
+
 recheck:
 	mlx5_dev_list_lock();
 	err = __mlx5_lag_dev_add_mdev(dev);
@@ -857,12 +857,13 @@
 bool mlx5_lag_is_roce(struct mlx5_core_dev *dev)
 {
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	bool res;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	res  = ldev && __mlx5_lag_is_roce(ldev);
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	return res;
 }
@@ -871,12 +872,13 @@
 bool mlx5_lag_is_active(struct mlx5_core_dev *dev)
 {
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	bool res;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	res  = ldev && __mlx5_lag_is_active(ldev);
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	return res;
 }
@@ -885,13 +887,14 @@
 bool mlx5_lag_is_master(struct mlx5_core_dev *dev)
 {
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	bool res;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	res = ldev && __mlx5_lag_is_active(ldev) &&
 		dev == ldev->pf[MLX5_LAG_P1].dev;
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	return res;
 }
@@ -900,12 +903,13 @@
 bool mlx5_lag_is_sriov(struct mlx5_core_dev *dev)
 {
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	bool res;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	res  = ldev && __mlx5_lag_is_sriov(ldev);
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	return res;
 }
@@ -914,12 +918,13 @@
 bool mlx5_lag_is_shared_fdb(struct mlx5_core_dev *dev)
 {
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	bool res;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	res = ldev && __mlx5_lag_is_sriov(ldev) && ldev->shared_fdb;
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	return res;
 }
@@ -967,8 +972,9 @@
 {
 	struct net_device *ndev = NULL;
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 
 	if (!(ldev && __mlx5_lag_is_roce(ldev)))
@@ -985,7 +991,7 @@
 		dev_hold(ndev);
 
 unlock:
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	return ndev;
 }
@@ -995,9 +1001,10 @@
 			   struct net_device *slave)
 {
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	u8 port = 0;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	if (!(ldev && __mlx5_lag_is_roce(ldev)))
 		goto unlock;
@@ -1010,7 +1017,7 @@
 	port = ldev->v2p_map[port];
 
 unlock:
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 	return port;
 }
 EXPORT_SYMBOL(mlx5_lag_get_slave_port);
@@ -1019,8 +1026,9 @@
 {
 	struct mlx5_core_dev *peer_dev = NULL;
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	if (!ldev)
 		goto unlock;
@@ -1030,7 +1038,7 @@
 			   ldev->pf[MLX5_LAG_P1].dev;
 
 unlock:
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 	return peer_dev;
 }
 EXPORT_SYMBOL(mlx5_lag_get_peer_mdev);
@@ -1043,6 +1051,7 @@
 	int outlen = MLX5_ST_SZ_BYTES(query_cong_statistics_out);
 	struct mlx5_core_dev *mdev[MLX5_MAX_PORTS];
 	struct mlx5_lag *ldev;
+	unsigned long flags;
 	int num_ports;
 	int ret, i, j;
 	void *out;
@@ -1053,7 +1062,7 @@
 
 	memset(values, 0, sizeof(*values) * num_counters);
 
-	spin_lock(&lag_lock);
+	spin_lock_irqsave(&lag_lock, flags);
 	ldev = mlx5_lag_dev(dev);
 	if (ldev && __mlx5_lag_is_active(ldev)) {
 		num_ports = MLX5_MAX_PORTS;
@@ -1063,7 +1072,7 @@
 		num_ports = 1;
 		mdev[MLX5_LAG_P1] = dev;
 	}
-	spin_unlock(&lag_lock);
+	spin_unlock_irqrestore(&lag_lock, flags);
 
 	for (i = 0; i < num_ports; ++i) {
 		u32 in[MLX5_ST_SZ_DW(query_cong_statistics_in)] = {};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lag_mp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lag_mp.c
@@ -100,6 +100,14 @@
 	flush_workqueue(mp->wq);
 }
 
+static void mlx5_lag_fib_set(struct lag_mp *mp, struct fib_info *fi, u32 dst, int dst_len)
+{
+	mp->fib.mfi = fi;
+	mp->fib.priority = fi->fib_priority;
+	mp->fib.dst = dst;
+	mp->fib.dst_len = dst_len;
+}
+
 struct mlx5_fib_event_work {
 	struct work_struct work;
 	struct mlx5_lag *ldev;
@@ -110,10 +118,10 @@
 	};
 };
 
-static void mlx5_lag_fib_route_event(struct mlx5_lag *ldev,
-				     unsigned long event,
-				     struct fib_info *fi)
+static void mlx5_lag_fib_route_event(struct mlx5_lag *ldev, unsigned long event,
+				     struct fib_entry_notifier_info *fen_info)
 {
+	struct fib_info *fi = fen_info->fi;
 	struct lag_mp *mp = &ldev->lag_mp;
 	struct fib_nh *fib_nh0, *fib_nh1;
 	unsigned int nhs;
@@ -121,11 +129,17 @@
 	/* Handle delete event */
 	if (event == FIB_EVENT_ENTRY_DEL) {
 		/* stop track */
-		if (mp->mfi == fi)
-			mp->mfi = NULL;
+		if (mp->fib.mfi == fi)
+			mp->fib.mfi = NULL;
 		return;
 	}
 
+	/* Handle multipath entry with lower priority value */
+	if (mp->fib.mfi && mp->fib.mfi != fi &&
+	    (mp->fib.dst != fen_info->dst || mp->fib.dst_len != fen_info->dst_len) &&
+	    fi->fib_priority >= mp->fib.priority)
+		return;
+
 	/* Handle add/replace event */
 	nhs = fib_info_num_path(fi);
 	if (nhs == 1) {
@@ -135,12 +149,13 @@
 			int i = mlx5_lag_dev_get_netdev_idx(ldev, nh_dev);
 
 			if (i < 0)
-				i = MLX5_LAG_NORMAL_AFFINITY;
-			else
-				++i;
+				return;
 
+			i++;
 			mlx5_lag_set_port_affinity(ldev, i);
+			mlx5_lag_fib_set(mp, fi, fen_info->dst, fen_info->dst_len);
 		}
+
 		return;
 	}
 
@@ -160,7 +175,7 @@
 	}
 
 	/* First time we see multipath route */
-	if (!mp->mfi && !__mlx5_lag_is_active(ldev)) {
+	if (!mp->fib.mfi && !__mlx5_lag_is_active(ldev)) {
 		struct lag_tracker tracker;
 
 		tracker = ldev->tracker;
@@ -168,7 +183,7 @@
 	}
 
 	mlx5_lag_set_port_affinity(ldev, MLX5_LAG_NORMAL_AFFINITY);
-	mp->mfi = fi;
+	mlx5_lag_fib_set(mp, fi, fen_info->dst, fen_info->dst_len);
 }
 
 static void mlx5_lag_fib_nexthop_event(struct mlx5_lag *ldev,
@@ -179,7 +194,7 @@
 	struct lag_mp *mp = &ldev->lag_mp;
 
 	/* Check the nh event is related to the route */
-	if (!mp->mfi || mp->mfi != fi)
+	if (!mp->fib.mfi || mp->fib.mfi != fi)
 		return;
 
 	/* nh added/removed */
@@ -209,7 +224,7 @@
 	case FIB_EVENT_ENTRY_REPLACE:
 	case FIB_EVENT_ENTRY_DEL:
 		mlx5_lag_fib_route_event(ldev, fib_work->event,
-					 fib_work->fen_info.fi);
+					 &fib_work->fen_info);
 		fib_info_put(fib_work->fen_info.fi);
 		break;
 	case FIB_EVENT_NH_ADD:
@@ -268,10 +283,8 @@
 		fen_info = container_of(info, struct fib_entry_notifier_info,
 					info);
 		fi = fen_info->fi;
-		if (fi->nh) {
-			NL_SET_ERR_MSG_MOD(info->extack, "IPv4 route with nexthop objects is not supported");
-			return notifier_from_errno(-EINVAL);
-		}
+		if (fi->nh)
+			return NOTIFY_DONE;
 		fib_dev = fib_info_nh(fen_info->fi, 0)->fib_nh_dev;
 		if (fib_dev != ldev->pf[MLX5_LAG_P1].netdev &&
 		    fib_dev != ldev->pf[MLX5_LAG_P2].netdev) {
@@ -310,7 +323,7 @@
 	/* Clear mfi, as it might become stale when a route delete event
 	 * has been missed, see mlx5_lag_fib_route_event().
 	 */
-	ldev->lag_mp.mfi = NULL;
+	ldev->lag_mp.fib.mfi = NULL;
 }
 
 int mlx5_lag_mp_init(struct mlx5_lag *ldev)
@@ -321,7 +334,7 @@
 	/* always clear mfi, as it might become stale when a route delete event
 	 * has been missed
 	 */
-	mp->mfi = NULL;
+	mp->fib.mfi = NULL;
 
 	if (mp->fib_nb.notifier_call)
 		return 0;
@@ -351,5 +364,5 @@
 	unregister_fib_notifier(&init_net, &mp->fib_nb);
 	destroy_workqueue(mp->wq);
 	mp->fib_nb.notifier_call = NULL;
-	mp->mfi = NULL;
+	mp->fib.mfi = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lag_mp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lag_mp.h
@@ -15,7 +15,12 @@
 
 struct lag_mp {
 	struct notifier_block     fib_nb;
-	struct fib_info           *mfi; /* used in tracking fib events */
+	struct {
+		const void        *mfi; /* used in tracking fib events */
+		u32               priority;
+		u32               dst;
+		int               dst_len;
+	} fib;
 	struct workqueue_struct   *wq;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/clock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/clock.c
@@ -177,23 +177,27 @@
 	}
 }
 
-static void mlx5_timestamp_overflow(struct work_struct *work)
+static long mlx5_timestamp_overflow(struct ptp_clock_info *ptp_info)
 {
-	struct delayed_work *dwork = to_delayed_work(work);
 	struct mlx5_core_dev *mdev;
 	struct mlx5_timer *timer;
 	struct mlx5_clock *clock;
 	unsigned long flags;
 
-	timer = container_of(dwork, struct mlx5_timer, overflow_work);
-	clock = container_of(timer, struct mlx5_clock, timer);
+	clock = container_of(ptp_info, struct mlx5_clock, ptp_info);
 	mdev = container_of(clock, struct mlx5_core_dev, clock);
+	timer = &clock->timer;
+
+	if (mdev->state == MLX5_DEVICE_STATE_INTERNAL_ERROR)
+		goto out;
 
 	write_seqlock_irqsave(&clock->lock, flags);
 	timecounter_read(&timer->tc);
 	mlx5_update_clock_info_page(mdev);
 	write_sequnlock_irqrestore(&clock->lock, flags);
-	schedule_delayed_work(&timer->overflow_work, timer->overflow_period);
+
+out:
+	return timer->overflow_period;
 }
 
 static int mlx5_ptp_settime_real_time(struct mlx5_core_dev *mdev,
@@ -361,6 +365,7 @@
 				       timer->nominal_c_mult + diff;
 	mlx5_update_clock_info_page(mdev);
 	write_sequnlock_irqrestore(&clock->lock, flags);
+	ptp_schedule_worker(clock->ptp, timer->overflow_period);
 
 	return 0;
 }
@@ -599,7 +604,7 @@
 static const struct ptp_clock_info mlx5_ptp_clock_info = {
 	.owner		= THIS_MODULE,
 	.name		= "mlx5_ptp",
-	.max_adj	= 100000000,
+	.max_adj	= 50000000,
 	.n_alarm	= 0,
 	.n_ext_ts	= 0,
 	.n_per_out	= 0,
@@ -611,6 +616,7 @@
 	.settime64	= mlx5_ptp_settime,
 	.enable		= NULL,
 	.verify		= NULL,
+	.do_aux_work	= mlx5_timestamp_overflow,
 };
 
 static int mlx5_query_mtpps_pin_mode(struct mlx5_core_dev *mdev, u8 pin,
@@ -804,12 +810,11 @@
 	do_div(ns, NSEC_PER_SEC / HZ);
 	timer->overflow_period = ns;
 
-	INIT_DELAYED_WORK(&timer->overflow_work, mlx5_timestamp_overflow);
-	if (timer->overflow_period)
-		schedule_delayed_work(&timer->overflow_work, 0);
-	else
+	if (!timer->overflow_period) {
+		timer->overflow_period = HZ;
 		mlx5_core_warn(mdev,
-			       "invalid overflow period, overflow_work is not scheduled\n");
+			       "invalid overflow period, overflow_work is scheduled once per second\n");
+	}
 
 	if (clock_info)
 		clock_info->overflow_period = timer->overflow_period;
@@ -895,6 +900,9 @@
 
 	MLX5_NB_INIT(&clock->pps_nb, mlx5_pps_event, PPS_EVENT);
 	mlx5_eq_notifier_register(mdev, &clock->pps_nb);
+
+	if (clock->ptp)
+		ptp_schedule_worker(clock->ptp, 0);
 }
 
 void mlx5_cleanup_clock(struct mlx5_core_dev *mdev)
@@ -911,7 +919,6 @@
 	}
 
 	cancel_work_sync(&clock->pps_info.out_work);
-	cancel_delayed_work_sync(&clock->timer.overflow_work);
 
 	if (mdev->clock_info) {
 		free_page((unsigned long)mdev->clock_info);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/devcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/devcom.c
@@ -3,6 +3,7 @@
 
 #include <linux/mlx5/vport.h>
 #include "lib/devcom.h"
+#include "mlx5_core.h"
 
 static LIST_HEAD(devcom_list);
 
@@ -13,8 +14,8 @@
 
 struct mlx5_devcom_component {
 	struct {
-		void *data;
-	} device[MLX5_MAX_PORTS];
+		void __rcu *data;
+	} device[MLX5_DEVCOM_PORTS_SUPPORTED];
 
 	mlx5_devcom_event_handler_t handler;
 	struct rw_semaphore sem;
@@ -25,7 +26,7 @@
 	struct list_head list;
 
 	struct mlx5_devcom_component components[MLX5_DEVCOM_NUM_COMPONENTS];
-	struct mlx5_core_dev *devs[MLX5_MAX_PORTS];
+	struct mlx5_core_dev *devs[MLX5_DEVCOM_PORTS_SUPPORTED];
 };
 
 struct mlx5_devcom {
@@ -74,13 +75,16 @@
 
 	if (!mlx5_core_is_pf(dev))
 		return NULL;
+	if (MLX5_CAP_GEN(dev, num_lag_ports) != MLX5_DEVCOM_PORTS_SUPPORTED)
+		return NULL;
 
+	mlx5_dev_list_lock();
 	sguid0 = mlx5_query_nic_system_image_guid(dev);
 	list_for_each_entry(iter, &devcom_list, list) {
 		struct mlx5_core_dev *tmp_dev = NULL;
 
 		idx = -1;
-		for (i = 0; i < MLX5_MAX_PORTS; i++) {
+		for (i = 0; i < MLX5_DEVCOM_PORTS_SUPPORTED; i++) {
 			if (iter->devs[i])
 				tmp_dev = iter->devs[i];
 			else
@@ -100,8 +104,10 @@
 
 	if (!priv) {
 		priv = mlx5_devcom_list_alloc();
-		if (!priv)
-			return ERR_PTR(-ENOMEM);
+		if (!priv) {
+			devcom = ERR_PTR(-ENOMEM);
+			goto out;
+		}
 
 		idx = 0;
 		new_priv = true;
@@ -110,13 +116,16 @@
 	priv->devs[idx] = dev;
 	devcom = mlx5_devcom_alloc(priv, idx);
 	if (!devcom) {
-		kfree(priv);
-		return ERR_PTR(-ENOMEM);
+		if (new_priv)
+			kfree(priv);
+		devcom = ERR_PTR(-ENOMEM);
+		goto out;
 	}
 
 	if (new_priv)
 		list_add(&priv->list, &devcom_list);
-
+out:
+	mlx5_dev_list_unlock();
 	return devcom;
 }
 
@@ -129,20 +138,23 @@
 	if (IS_ERR_OR_NULL(devcom))
 		return;
 
+	mlx5_dev_list_lock();
 	priv = devcom->priv;
 	priv->devs[devcom->idx] = NULL;
 
 	kfree(devcom);
 
-	for (i = 0; i < MLX5_MAX_PORTS; i++)
+	for (i = 0; i < MLX5_DEVCOM_PORTS_SUPPORTED; i++)
 		if (priv->devs[i])
 			break;
 
-	if (i != MLX5_MAX_PORTS)
-		return;
+	if (i != MLX5_DEVCOM_PORTS_SUPPORTED)
+		goto out;
 
 	list_del(&priv->list);
 	kfree(priv);
+out:
+	mlx5_dev_list_unlock();
 }
 
 void mlx5_devcom_register_component(struct mlx5_devcom *devcom,
@@ -160,7 +172,7 @@
 	comp = &devcom->priv->components[id];
 	down_write(&comp->sem);
 	comp->handler = handler;
-	comp->device[devcom->idx].data = data;
+	rcu_assign_pointer(comp->device[devcom->idx].data, data);
 	up_write(&comp->sem);
 }
 
@@ -174,8 +186,9 @@
 
 	comp = &devcom->priv->components[id];
 	down_write(&comp->sem);
-	comp->device[devcom->idx].data = NULL;
+	RCU_INIT_POINTER(comp->device[devcom->idx].data, NULL);
 	up_write(&comp->sem);
+	synchronize_rcu();
 }
 
 int mlx5_devcom_send_event(struct mlx5_devcom *devcom,
@@ -191,12 +204,15 @@
 
 	comp = &devcom->priv->components[id];
 	down_write(&comp->sem);
-	for (i = 0; i < MLX5_MAX_PORTS; i++)
-		if (i != devcom->idx && comp->device[i].data) {
-			err = comp->handler(event, comp->device[i].data,
-					    event_data);
+	for (i = 0; i < MLX5_DEVCOM_PORTS_SUPPORTED; i++) {
+		void *data = rcu_dereference_protected(comp->device[i].data,
+						       lockdep_is_held(&comp->sem));
+
+		if (i != devcom->idx && data) {
+			err = comp->handler(event, data, event_data);
 			break;
 		}
+	}
 
 	up_write(&comp->sem);
 	return err;
@@ -211,7 +227,7 @@
 	comp = &devcom->priv->components[id];
 	WARN_ON(!rwsem_is_locked(&comp->sem));
 
-	comp->paired = paired;
+	WRITE_ONCE(comp->paired, paired);
 }
 
 bool mlx5_devcom_is_paired(struct mlx5_devcom *devcom,
@@ -220,7 +236,7 @@
 	if (IS_ERR_OR_NULL(devcom))
 		return false;
 
-	return devcom->priv->components[id].paired;
+	return READ_ONCE(devcom->priv->components[id].paired);
 }
 
 void *mlx5_devcom_get_peer_data(struct mlx5_devcom *devcom,
@@ -234,16 +250,38 @@
 
 	comp = &devcom->priv->components[id];
 	down_read(&comp->sem);
-	if (!comp->paired) {
+	if (!READ_ONCE(comp->paired)) {
 		up_read(&comp->sem);
 		return NULL;
 	}
 
-	for (i = 0; i < MLX5_MAX_PORTS; i++)
+	for (i = 0; i < MLX5_DEVCOM_PORTS_SUPPORTED; i++)
 		if (i != devcom->idx)
 			break;
 
-	return comp->device[i].data;
+	return rcu_dereference_protected(comp->device[i].data, lockdep_is_held(&comp->sem));
+}
+
+void *mlx5_devcom_get_peer_data_rcu(struct mlx5_devcom *devcom, enum mlx5_devcom_components id)
+{
+	struct mlx5_devcom_component *comp;
+	int i;
+
+	if (IS_ERR_OR_NULL(devcom))
+		return NULL;
+
+	for (i = 0; i < MLX5_DEVCOM_PORTS_SUPPORTED; i++)
+		if (i != devcom->idx)
+			break;
+
+	comp = &devcom->priv->components[id];
+	/* This can change concurrently, however 'data' pointer will remain
+	 * valid for the duration of RCU read section.
+	 */
+	if (!READ_ONCE(comp->paired))
+		return NULL;
+
+	return rcu_dereference(comp->device[i].data);
 }
 
 void mlx5_devcom_release_peer_data(struct mlx5_devcom *devcom,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/devcom.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/devcom.h
@@ -6,6 +6,8 @@
 
 #include <linux/mlx5/driver.h>
 
+#define MLX5_DEVCOM_PORTS_SUPPORTED 2
+
 enum mlx5_devcom_components {
 	MLX5_DEVCOM_ESW_OFFLOADS,
 
@@ -39,6 +41,7 @@
 
 void *mlx5_devcom_get_peer_data(struct mlx5_devcom *devcom,
 				enum mlx5_devcom_components id);
+void *mlx5_devcom_get_peer_data_rcu(struct mlx5_devcom *devcom, enum mlx5_devcom_components id);
 void mlx5_devcom_release_peer_data(struct mlx5_devcom *devcom,
 				   enum mlx5_devcom_components id);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/fs_chains.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/fs_chains.c
@@ -124,6 +124,10 @@
 	if (mlx5_chains_ignore_flow_level_supported(chains))
 		return UINT_MAX;
 
+	if (!chains->dev->priv.eswitch ||
+	    chains->dev->priv.eswitch->mode != MLX5_ESWITCH_OFFLOADS)
+		return 1;
+
 	/* We should get here only for eswitch case */
 	return FDB_TC_MAX_PRIO;
 }
@@ -192,6 +196,11 @@
 		ns = mlx5_get_flow_namespace(chains->dev, chains->ns);
 	}
 
+	if (!ns) {
+		mlx5_core_warn(chains->dev, "Failed to get flow namespace\n");
+		return ERR_PTR(-EOPNOTSUPP);
+	}
+
 	ft_attr.autogroup.num_reserved_entries = 2;
 	ft_attr.autogroup.max_num_groups = chains->group_num;
 	ft = mlx5_create_auto_grouped_flow_table(ns, &ft_attr);
@@ -208,7 +217,7 @@
 create_chain_restore(struct fs_chain *chain)
 {
 	struct mlx5_eswitch *esw = chain->chains->dev->priv.eswitch;
-	char modact[MLX5_UN_SZ_BYTES(set_add_copy_action_in_auto)];
+	u8 modact[MLX5_UN_SZ_BYTES(set_add_copy_action_in_auto)] = {};
 	struct mlx5_fs_chains *chains = chain->chains;
 	enum mlx5e_tc_attr_to_reg chain_to_reg;
 	struct mlx5_modify_hdr *mod_hdr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/geneve.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/geneve.c
@@ -105,6 +105,7 @@
 		geneve->opt_type = opt->type;
 		geneve->obj_id = res;
 		geneve->refcount++;
+		res = 0;
 	}
 
 unlock:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/mpfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/mpfs.c
@@ -122,7 +122,7 @@
 {
 	struct mlx5_mpfs *mpfs = dev->priv.mpfs;
 
-	if (!MLX5_ESWITCH_MANAGER(dev))
+	if (!mpfs)
 		return;
 
 	WARN_ON(!hlist_empty(mpfs->hash));
@@ -137,7 +137,7 @@
 	int err = 0;
 	u32 index;
 
-	if (!MLX5_ESWITCH_MANAGER(dev))
+	if (!mpfs)
 		return 0;
 
 	mutex_lock(&mpfs->lock);
@@ -185,7 +185,7 @@
 	int err = 0;
 	u32 index;
 
-	if (!MLX5_ESWITCH_MANAGER(dev))
+	if (!mpfs)
 		return 0;
 
 	mutex_lock(&mpfs->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/lib/pci_vsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/lib/pci_vsc.c
@@ -24,6 +24,11 @@
 	pci_write_config_dword((dev)->pdev, (dev)->vsc_addr + (offset), (val))
 #define VSC_MAX_RETRIES 2048
 
+/* Reading VSC registers can take relatively long time.
+ * Yield the cpu every 128 registers read.
+ */
+#define VSC_GW_READ_BLOCK_COUNT 128
+
 enum {
 	VSC_CTRL_OFFSET = 0x4,
 	VSC_COUNTER_OFFSET = 0x8,
@@ -269,6 +274,7 @@
 {
 	unsigned int next_read_addr = 0;
 	unsigned int read_addr = 0;
+	unsigned int count = 0;
 
 	while (read_addr < length) {
 		if (mlx5_vsc_gw_read_fast(dev, read_addr, &next_read_addr,
@@ -276,6 +282,10 @@
 			return read_addr;
 
 		read_addr = next_read_addr;
+		if (++count == VSC_GW_READ_BLOCK_COUNT) {
+			cond_resched();
+			count = 0;
+		}
 	}
 	return length;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/main.c
@@ -97,6 +97,8 @@
 	MLX5_ATOMIC_REQ_MODE_HOST_ENDIANNESS = 0x1,
 };
 
+#define LOG_MAX_SUPPORTED_QPS 0xff
+
 static struct mlx5_profile profile[] = {
 	[0] = {
 		.mask           = 0,
@@ -108,7 +110,7 @@
 	[2] = {
 		.mask		= MLX5_PROF_MASK_QP_SIZE |
 				  MLX5_PROF_MASK_MR_CACHE,
-		.log_max_qp	= 18,
+		.log_max_qp	= LOG_MAX_SUPPORTED_QPS,
 		.mr_cache[0]	= {
 			.size	= 500,
 			.limit	= 250
@@ -513,7 +515,9 @@
 		 to_fw_pkey_sz(dev, 128));
 
 	/* Check log_max_qp from HCA caps to set in current profile */
-	if (MLX5_CAP_GEN_MAX(dev, log_max_qp) < prof->log_max_qp) {
+	if (prof->log_max_qp == LOG_MAX_SUPPORTED_QPS) {
+		prof->log_max_qp = min_t(u8, 18, MLX5_CAP_GEN_MAX(dev, log_max_qp));
+	} else if (MLX5_CAP_GEN_MAX(dev, log_max_qp) < prof->log_max_qp) {
 		mlx5_core_warn(dev, "log_max_qp value in current profile is %d, changing it to HCA capability limit (%d)\n",
 			       prof->log_max_qp,
 			       MLX5_CAP_GEN_MAX(dev, log_max_qp));
@@ -777,7 +781,6 @@
 	}
 
 	mlx5_pci_vsc_init(dev);
-	dev->caps.embedded_cpu = mlx5_read_embedded_cpu(dev);
 	return 0;
 
 err_clr_master:
@@ -899,7 +902,7 @@
 
 	dev->dm = mlx5_dm_create(dev);
 	if (IS_ERR(dev->dm))
-		mlx5_core_warn(dev, "Failed to init device memory%d\n", err);
+		mlx5_core_warn(dev, "Failed to init device memory %ld\n", PTR_ERR(dev->dm));
 
 	dev->tracer = mlx5_fw_tracer_create(dev);
 	dev->hv_vhca = mlx5_hv_vhca_create(dev);
@@ -924,6 +927,8 @@
 err_tables_cleanup:
 	mlx5_geneve_destroy(dev->geneve);
 	mlx5_vxlan_destroy(dev->vxlan);
+	mlx5_cleanup_clock(dev);
+	mlx5_cleanup_reserved_gids(dev);
 	mlx5_cq_debugfs_cleanup(dev);
 	mlx5_fw_reset_cleanup(dev);
 err_events_cleanup:
@@ -997,6 +1002,7 @@
 		goto err_cmd_cleanup;
 	}
 
+	dev->caps.embedded_cpu = mlx5_read_embedded_cpu(dev);
 	mlx5_cmd_set_state(dev, MLX5_CMDIF_STATE_UP);
 
 	err = mlx5_core_enable_hca(dev, 0);
@@ -1423,7 +1429,9 @@
 	memcpy(&dev->profile, &profile[profile_idx], sizeof(dev->profile));
 	INIT_LIST_HEAD(&priv->ctx_list);
 	spin_lock_init(&priv->ctx_lock);
+	lockdep_register_key(&dev->lock_key);
 	mutex_init(&dev->intf_state_mutex);
+	lockdep_set_class(&dev->intf_state_mutex, &dev->lock_key);
 
 	mutex_init(&priv->bfregs.reg_head.lock);
 	mutex_init(&priv->bfregs.wc_head.lock);
@@ -1470,6 +1478,7 @@
 	mutex_destroy(&priv->bfregs.wc_head.lock);
 	mutex_destroy(&priv->bfregs.reg_head.lock);
 	mutex_destroy(&dev->intf_state_mutex);
+	lockdep_unregister_key(&dev->lock_key);
 	return err;
 }
 
@@ -1487,6 +1496,7 @@
 	mutex_destroy(&priv->bfregs.wc_head.lock);
 	mutex_destroy(&priv->bfregs.reg_head.lock);
 	mutex_destroy(&dev->intf_state_mutex);
+	lockdep_unregister_key(&dev->lock_key);
 }
 
 static int probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
@@ -1568,12 +1578,28 @@
 	mlx5_devlink_free(devlink);
 }
 
+#define mlx5_pci_trace(dev, fmt, ...) ({ \
+	struct mlx5_core_dev *__dev = (dev); \
+	mlx5_core_info(__dev, "%s Device state = %d health sensors: %d pci_status: %d. " fmt, \
+		       __func__, __dev->state, mlx5_health_check_fatal_sensors(__dev), \
+		       __dev->pci_status, ##__VA_ARGS__); \
+})
+
+static const char *result2str(enum pci_ers_result result)
+{
+	return  result == PCI_ERS_RESULT_NEED_RESET ? "need reset" :
+		result == PCI_ERS_RESULT_DISCONNECT ? "disconnect" :
+		result == PCI_ERS_RESULT_RECOVERED  ? "recovered" :
+		"unknown";
+}
+
 static pci_ers_result_t mlx5_pci_err_detected(struct pci_dev *pdev,
 					      pci_channel_state_t state)
 {
 	struct mlx5_core_dev *dev = pci_get_drvdata(pdev);
+	enum pci_ers_result res;
 
-	mlx5_core_info(dev, "%s was called\n", __func__);
+	mlx5_pci_trace(dev, "Enter, pci channel state = %d\n", state);
 
 	mlx5_enter_error_state(dev, false);
 	mlx5_error_sw_reset(dev);
@@ -1581,8 +1607,12 @@
 	mlx5_drain_health_wq(dev);
 	mlx5_pci_disable_device(dev);
 
-	return state == pci_channel_io_perm_failure ?
+	res = state == pci_channel_io_perm_failure ?
 		PCI_ERS_RESULT_DISCONNECT : PCI_ERS_RESULT_NEED_RESET;
+
+	mlx5_core_info(dev, "%s Device state = %d pci_status: %d. Exit, result = %d, %s\n",
+		       __func__, dev->state, dev->pci_status, res, result2str(res));
+	return res;
 }
 
 /* wait for the device to show vital signs by waiting
@@ -1616,28 +1646,36 @@
 
 static pci_ers_result_t mlx5_pci_slot_reset(struct pci_dev *pdev)
 {
+	enum pci_ers_result res = PCI_ERS_RESULT_DISCONNECT;
 	struct mlx5_core_dev *dev = pci_get_drvdata(pdev);
 	int err;
 
-	mlx5_core_info(dev, "%s was called\n", __func__);
+	mlx5_core_info(dev, "%s Device state = %d pci_status: %d. Enter\n",
+		       __func__, dev->state, dev->pci_status);
 
 	err = mlx5_pci_enable_device(dev);
 	if (err) {
 		mlx5_core_err(dev, "%s: mlx5_pci_enable_device failed with error code: %d\n",
 			      __func__, err);
-		return PCI_ERS_RESULT_DISCONNECT;
+		goto out;
 	}
 
 	pci_set_master(pdev);
 	pci_restore_state(pdev);
 	pci_save_state(pdev);
 
-	if (wait_vital(pdev)) {
-		mlx5_core_err(dev, "%s: wait_vital timed out\n", __func__);
-		return PCI_ERS_RESULT_DISCONNECT;
+	err = wait_vital(pdev);
+	if (err) {
+		mlx5_core_err(dev, "%s: wait vital failed with error code: %d\n",
+			      __func__, err);
+		goto out;
 	}
 
-	return PCI_ERS_RESULT_RECOVERED;
+	res = PCI_ERS_RESULT_RECOVERED;
+out:
+	mlx5_core_info(dev, "%s Device state = %d pci_status: %d. Exit, err = %d, result = %d, %s\n",
+		       __func__, dev->state, dev->pci_status, err, res, result2str(res));
+	return res;
 }
 
 static void mlx5_pci_resume(struct pci_dev *pdev)
@@ -1645,14 +1683,16 @@
 	struct mlx5_core_dev *dev = pci_get_drvdata(pdev);
 	int err;
 
-	mlx5_core_info(dev, "%s was called\n", __func__);
+	mlx5_pci_trace(dev, "Enter, loading driver..\n");
 
 	err = mlx5_load_one(dev);
-	if (err)
-		mlx5_core_err(dev, "%s: mlx5_load_one failed with error code: %d\n",
-			      __func__, err);
-	else
-		mlx5_core_info(dev, "%s: device recovered\n", __func__);
+
+	if (!err)
+		devlink_health_reporter_state_update(dev->priv.health.fw_fatal_reporter,
+						     DEVLINK_HEALTH_REPORTER_STATE_HEALTHY);
+
+	mlx5_pci_trace(dev, "Done, err = %d, device %s\n", err,
+		       !err ? "recovered" : "Failed");
 }
 
 static const struct pci_error_handlers mlx5_err_handler = {
@@ -1756,10 +1796,12 @@
 	{ PCI_VDEVICE(MELLANOX, 0x101e), MLX5_PCI_DEV_IS_VF},	/* ConnectX Family mlx5Gen Virtual Function */
 	{ PCI_VDEVICE(MELLANOX, 0x101f) },			/* ConnectX-6 LX */
 	{ PCI_VDEVICE(MELLANOX, 0x1021) },			/* ConnectX-7 */
+	{ PCI_VDEVICE(MELLANOX, 0x1023) },			/* ConnectX-8 */
 	{ PCI_VDEVICE(MELLANOX, 0xa2d2) },			/* BlueField integrated ConnectX-5 network controller */
 	{ PCI_VDEVICE(MELLANOX, 0xa2d3), MLX5_PCI_DEV_IS_VF},	/* BlueField integrated ConnectX-5 network controller VF */
 	{ PCI_VDEVICE(MELLANOX, 0xa2d6) },			/* BlueField-2 integrated ConnectX-6 Dx network controller */
 	{ PCI_VDEVICE(MELLANOX, 0xa2dc) },			/* BlueField-3 integrated ConnectX-7 network controller */
+	{ PCI_VDEVICE(MELLANOX, 0xa2df) },			/* BlueField-4 integrated ConnectX-8 network controller */
 	{ 0, }
 };
 
@@ -1773,12 +1815,13 @@
 
 int mlx5_recover_device(struct mlx5_core_dev *dev)
 {
-	int ret = -EIO;
+	if (!mlx5_core_is_sf(dev)) {
+		mlx5_pci_disable_device(dev);
+		if (mlx5_pci_slot_reset(dev->pdev) != PCI_ERS_RESULT_RECOVERED)
+			return -EIO;
+	}
 
-	mlx5_pci_disable_device(dev);
-	if (mlx5_pci_slot_reset(dev->pdev) == PCI_ERS_RESULT_RECOVERED)
-		ret = mlx5_load_one(dev);
-	return ret;
+	return mlx5_load_one(dev);
 }
 
 static struct pci_driver mlx5_core_driver = {
@@ -1806,7 +1849,7 @@
 	}
 }
 
-static int __init init(void)
+static int __init mlx5_init(void)
 {
 	int err;
 
@@ -1819,7 +1862,7 @@
 	mlx5_fpga_ipsec_build_fs_cmds();
 	mlx5_register_debugfs();
 
-	err = pci_register_driver(&mlx5_core_driver);
+	err = mlx5e_init();
 	if (err)
 		goto err_debug;
 
@@ -1827,28 +1870,28 @@
 	if (err)
 		goto err_sf;
 
-	err = mlx5e_init();
+	err = pci_register_driver(&mlx5_core_driver);
 	if (err)
-		goto err_en;
+		goto err_pci;
 
 	return 0;
 
-err_en:
+err_pci:
 	mlx5_sf_driver_unregister();
 err_sf:
-	pci_unregister_driver(&mlx5_core_driver);
+	mlx5e_cleanup();
 err_debug:
 	mlx5_unregister_debugfs();
 	return err;
 }
 
-static void __exit cleanup(void)
+static void __exit mlx5_cleanup(void)
 {
-	mlx5e_cleanup();
-	mlx5_sf_driver_unregister();
 	pci_unregister_driver(&mlx5_core_driver);
+	mlx5_sf_driver_unregister();
+	mlx5e_cleanup();
 	mlx5_unregister_debugfs();
 }
 
-module_init(init);
-module_exit(cleanup);
+module_init(mlx5_init);
+module_exit(mlx5_cleanup);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.h
@@ -186,6 +186,7 @@
 int mlx5_register_device(struct mlx5_core_dev *dev);
 void mlx5_unregister_device(struct mlx5_core_dev *dev);
 struct mlx5_core_dev *mlx5_get_next_phys_dev(struct mlx5_core_dev *dev);
+struct mlx5_core_dev *mlx5_get_next_phys_dev_lag(struct mlx5_core_dev *dev);
 void mlx5_dev_list_lock(void);
 void mlx5_dev_list_unlock(void);
 int mlx5_dev_list_trylock(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/mlx5_irq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/mlx5_irq.h
@@ -16,6 +16,7 @@
 void mlx5_irq_table_cleanup(struct mlx5_core_dev *dev);
 int mlx5_irq_table_create(struct mlx5_core_dev *dev);
 void mlx5_irq_table_destroy(struct mlx5_core_dev *dev);
+void mlx5_irq_table_free_irqs(struct mlx5_core_dev *dev);
 int mlx5_irq_table_get_num_comp(struct mlx5_irq_table *table);
 int mlx5_irq_table_get_sfs_vec(struct mlx5_irq_table *table);
 struct mlx5_irq_table *mlx5_irq_table_get(struct mlx5_core_dev *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/mr.c
@@ -52,7 +52,6 @@
 
 	mkc = MLX5_ADDR_OF(create_mkey_in, in, memory_key_mkey_entry);
 	mkey_index = MLX5_GET(create_mkey_out, lout, mkey_index);
-	mkey->iova = MLX5_GET64(mkc, mkc, start_addr);
 	mkey->size = MLX5_GET64(mkc, mkc, len);
 	mkey->key = (u32)mlx5_mkey_variant(mkey->key) | mlx5_idx_to_mkey(mkey_index);
 	mkey->pd = MLX5_GET(mkc, mkc, pd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c
@@ -216,7 +216,8 @@
 
 	n = find_first_bit(&fp->bitmask, 8 * sizeof(fp->bitmask));
 	if (n >= MLX5_NUM_4K_IN_PAGE) {
-		mlx5_core_warn(dev, "alloc 4k bug\n");
+		mlx5_core_warn(dev, "alloc 4k bug: fw page = 0x%llx, n = %u, bitmask: %lu, max num of 4K pages: %d\n",
+			       fp->addr, n, fp->bitmask,  MLX5_NUM_4K_IN_PAGE);
 		return -ENOENT;
 	}
 	clear_bit(n, &fp->bitmask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c
@@ -138,18 +138,23 @@
 	return ret;
 }
 
-static void irq_release(struct mlx5_irq *irq)
+static void mlx5_system_free_irq(struct mlx5_irq *irq)
 {
-	struct mlx5_irq_pool *pool = irq->pool;
-
-	xa_erase(&pool->irqs, irq->index);
 	/* free_irq requires that affinity and rmap will be cleared
 	 * before calling it. This is why there is asymmetry with set_rmap
 	 * which should be called after alloc_irq but before request_irq.
 	 */
 	irq_set_affinity_hint(irq->irqn, NULL);
-	free_cpumask_var(irq->mask);
 	free_irq(irq->irqn, &irq->nh);
+}
+
+static void irq_release(struct mlx5_irq *irq)
+{
+	struct mlx5_irq_pool *pool = irq->pool;
+
+	xa_erase(&pool->irqs, irq->index);
+	mlx5_system_free_irq(irq);
+	free_cpumask_var(irq->mask);
 	kfree(irq);
 }
 
@@ -346,8 +351,8 @@
 	new_irq = irq_pool_create_irq(pool, affinity);
 	if (IS_ERR(new_irq)) {
 		if (!least_loaded_irq) {
-			mlx5_core_err(pool->dev, "Didn't find IRQ for cpu = %u\n",
-				      cpumask_first(affinity));
+			mlx5_core_err(pool->dev, "Didn't find a matching IRQ. err = %ld\n",
+				      PTR_ERR(new_irq));
 			mutex_unlock(&pool->lock);
 			return new_irq;
 		}
@@ -469,7 +474,7 @@
 	pool->min_threshold = min_threshold * MLX5_EQ_REFS_PER_IRQ;
 	pool->max_threshold = max_threshold * MLX5_EQ_REFS_PER_IRQ;
 	mlx5_core_dbg(dev, "pool->name = %s, pool->size = %d, pool->start = %d",
-		      name, size, start);
+		      name ? name : "mlx5_pcif_pool", size, start);
 	return pool;
 }
 
@@ -550,6 +555,24 @@
 	irq_pool_free(table->pf_pool);
 }
 
+static void mlx5_irq_pool_free_irqs(struct mlx5_irq_pool *pool)
+{
+	struct mlx5_irq *irq;
+	unsigned long index;
+
+	xa_for_each(&pool->irqs, index, irq)
+		mlx5_system_free_irq(irq);
+}
+
+static void mlx5_irq_pools_free_irqs(struct mlx5_irq_table *table)
+{
+	if (table->sf_ctrl_pool) {
+		mlx5_irq_pool_free_irqs(table->sf_comp_pool);
+		mlx5_irq_pool_free_irqs(table->sf_ctrl_pool);
+	}
+	mlx5_irq_pool_free_irqs(table->pf_pool);
+}
+
 /* irq_table API */
 
 int mlx5_irq_table_init(struct mlx5_core_dev *dev)
@@ -630,6 +653,17 @@
 	pci_free_irq_vectors(dev->pdev);
 }
 
+void mlx5_irq_table_free_irqs(struct mlx5_core_dev *dev)
+{
+	struct mlx5_irq_table *table = dev->priv.irq_table;
+
+	if (mlx5_core_is_sf(dev))
+		return;
+
+	mlx5_irq_pools_free_irqs(table);
+	pci_free_irq_vectors(dev->pdev);
+}
+
 int mlx5_irq_table_get_sfs_vec(struct mlx5_irq_table *table)
 {
 	if (table->sf_comp_pool)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/port.c
@@ -406,23 +406,24 @@
 
 	switch (module_id) {
 	case MLX5_MODULE_ID_SFP:
-		mlx5_sfp_eeprom_params_set(&query.i2c_address, &query.page, &query.offset);
+		mlx5_sfp_eeprom_params_set(&query.i2c_address, &query.page, &offset);
 		break;
 	case MLX5_MODULE_ID_QSFP:
 	case MLX5_MODULE_ID_QSFP_PLUS:
 	case MLX5_MODULE_ID_QSFP28:
-		mlx5_qsfp_eeprom_params_set(&query.i2c_address, &query.page, &query.offset);
+		mlx5_qsfp_eeprom_params_set(&query.i2c_address, &query.page, &offset);
 		break;
 	default:
 		mlx5_core_err(dev, "Module ID not recognized: 0x%x\n", module_id);
 		return -EINVAL;
 	}
 
-	if (query.offset + size > MLX5_EEPROM_PAGE_LENGTH)
+	if (offset + size > MLX5_EEPROM_PAGE_LENGTH)
 		/* Cross pages read, read until offset 256 in low page */
-		size -= offset + size - MLX5_EEPROM_PAGE_LENGTH;
+		size = MLX5_EEPROM_PAGE_LENGTH - offset;
 
 	query.size = size;
+	query.offset = offset;
 
 	return mlx5_query_mcia(dev, &query, data);
 }
@@ -432,35 +433,12 @@
 				     struct mlx5_module_eeprom_query_params *params,
 				     u8 *data)
 {
-	u8 module_id;
 	int err;
 
 	err = mlx5_query_module_num(dev, &params->module_number);
 	if (err)
 		return err;
 
-	err = mlx5_query_module_id(dev, params->module_number, &module_id);
-	if (err)
-		return err;
-
-	switch (module_id) {
-	case MLX5_MODULE_ID_SFP:
-		if (params->page > 0)
-			return -EINVAL;
-		break;
-	case MLX5_MODULE_ID_QSFP:
-	case MLX5_MODULE_ID_QSFP28:
-	case MLX5_MODULE_ID_QSFP_PLUS:
-		if (params->page > 3)
-			return -EINVAL;
-		break;
-	case MLX5_MODULE_ID_DSFP:
-		break;
-	default:
-		mlx5_core_err(dev, "Module ID not recognized: 0x%x\n", module_id);
-		return -EINVAL;
-	}
-
 	if (params->i2c_address != MLX5_I2C_ADDR_HIGH &&
 	    params->i2c_address != MLX5_I2C_ADDR_LOW) {
 		mlx5_core_err(dev, "I2C address not recognized: 0x%x\n", params->i2c_address);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/sf/dev/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/sf/dev/dev.c
@@ -28,10 +28,7 @@
 {
 	struct mlx5_sf_dev_table *table = dev->priv.sf_dev_table;
 
-	if (!mlx5_sf_dev_supported(dev))
-		return false;
-
-	return !xa_empty(&table->devices);
+	return table && !xa_empty(&table->devices);
 }
 
 static ssize_t sfnum_show(struct device *dev, struct device_attribute *attr, char *buf)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/sriov.c
@@ -256,8 +256,7 @@
 		host_total_vfs = MLX5_GET(query_esw_functions_out, out,
 					  host_params_context.host_total_vfs);
 		kvfree(out);
-		if (host_total_vfs)
-			return host_total_vfs;
+		return host_total_vfs;
 	}
 
 done:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c
@@ -39,6 +39,7 @@
 	[DR_ACTION_TYP_VPORT] = "DR_ACTION_TYP_VPORT",
 	[DR_ACTION_TYP_POP_VLAN] = "DR_ACTION_TYP_POP_VLAN",
 	[DR_ACTION_TYP_PUSH_VLAN] = "DR_ACTION_TYP_PUSH_VLAN",
+	[DR_ACTION_TYP_SAMPLER] = "DR_ACTION_TYP_SAMPLER",
 	[DR_ACTION_TYP_INSERT_HDR] = "DR_ACTION_TYP_INSERT_HDR",
 	[DR_ACTION_TYP_REMOVE_HDR] = "DR_ACTION_TYP_REMOVE_HDR",
 	[DR_ACTION_TYP_MAX] = "DR_ACTION_UNKNOWN",
@@ -513,9 +514,9 @@
 		/* If destination is vport we will get the FW flow table
 		 * that recalculates the CS and forwards to the vport.
 		 */
-		ret = mlx5dr_domain_cache_get_recalc_cs_ft_addr(dest_action->vport->dmn,
-								dest_action->vport->caps->num,
-								final_icm_addr);
+		ret = mlx5dr_domain_get_recalc_cs_ft_addr(dest_action->vport->dmn,
+							  dest_action->vport->caps->num,
+							  final_icm_addr);
 		if (ret) {
 			mlx5dr_err(dmn, "Failed to get FW cs recalc flow table\n");
 			return ret;
@@ -579,6 +580,7 @@
 		switch (action_type) {
 		case DR_ACTION_TYP_DROP:
 			attr.final_icm_addr = nic_dmn->drop_icm_addr;
+			attr.hit_gvmi = nic_dmn->drop_icm_addr >> 48;
 			break;
 		case DR_ACTION_TYP_FT:
 			dest_action = action;
@@ -632,7 +634,7 @@
 			return -EOPNOTSUPP;
 		case DR_ACTION_TYP_CTR:
 			attr.ctr_id = action->ctr->ctr_id +
-				action->ctr->offeset;
+				action->ctr->offset;
 			break;
 		case DR_ACTION_TYP_TAG:
 			attr.flow_tag = action->flow_tag->flow_tag;
@@ -666,16 +668,16 @@
 							action->sampler->tx_icm_addr;
 			break;
 		case DR_ACTION_TYP_VPORT:
-			attr.hit_gvmi = action->vport->caps->vhca_gvmi;
-			dest_action = action;
-			if (rx_rule) {
-				if (action->vport->caps->num == WIRE_PORT) {
-					mlx5dr_dbg(dmn, "Device doesn't support Loopback on WIRE vport\n");
-					return -EOPNOTSUPP;
-				}
-				attr.final_icm_addr = action->vport->caps->icm_address_rx;
+			if (unlikely(rx_rule && action->vport->caps->num == MLX5_VPORT_UPLINK)) {
+				/* can't go to uplink on RX rule - dropping instead */
+				attr.final_icm_addr = nic_dmn->drop_icm_addr;
+				attr.hit_gvmi = nic_dmn->drop_icm_addr >> 48;
 			} else {
-				attr.final_icm_addr = action->vport->caps->icm_address_tx;
+				attr.hit_gvmi = action->vport->caps->vhca_gvmi;
+				dest_action = action;
+				attr.final_icm_addr = rx_rule ?
+						      action->vport->caps->icm_address_rx :
+						      action->vport->caps->icm_address_tx;
 			}
 			break;
 		case DR_ACTION_TYP_POP_VLAN:
@@ -846,7 +848,8 @@
 mlx5dr_action_create_mult_dest_tbl(struct mlx5dr_domain *dmn,
 				   struct mlx5dr_action_dest *dests,
 				   u32 num_of_dests,
-				   bool ignore_flow_level)
+				   bool ignore_flow_level,
+				   u32 flow_source)
 {
 	struct mlx5dr_cmd_flow_destination_hw_info *hw_dests;
 	struct mlx5dr_action **ref_actions;
@@ -914,7 +917,8 @@
 				      reformat_req,
 				      &action->dest_tbl->fw_tbl.id,
 				      &action->dest_tbl->fw_tbl.group_id,
-				      ignore_flow_level);
+				      ignore_flow_level,
+				      flow_source);
 	if (ret)
 		goto free_action;
 
@@ -1555,6 +1559,12 @@
 	return sw_field == MLX5_ACTION_IN_FIELD_OUT_IP_TTL;
 }
 
+static bool dr_action_modify_ttl_ignore(struct mlx5dr_domain *dmn)
+{
+	return !mlx5dr_ste_supp_ttl_cs_recalc(&dmn->info.caps) &&
+	       !MLX5_CAP_ESW_FLOWTABLE(dmn->mdev, fdb_ipv4_ttl_modify);
+}
+
 static int dr_actions_convert_modify_header(struct mlx5dr_action *action,
 					    u32 max_hw_actions,
 					    u32 num_sw_actions,
@@ -1586,8 +1596,13 @@
 		if (ret)
 			return ret;
 
-		if (!(*modify_ttl))
-			*modify_ttl = dr_action_modify_check_is_ttl_modify(sw_action);
+		if (!(*modify_ttl) &&
+		    dr_action_modify_check_is_ttl_modify(sw_action)) {
+			if (dr_action_modify_ttl_ignore(dmn))
+				continue;
+
+			*modify_ttl = true;
+		}
 
 		/* Convert SW action to HW action */
 		ret = dr_action_modify_sw_to_hw(dmn,
@@ -1626,7 +1641,7 @@
 			 * modify actions doesn't exceeds the limit
 			 */
 			hw_idx++;
-			if ((num_sw_actions + hw_idx - i) >= max_hw_actions) {
+			if (hw_idx >= max_hw_actions) {
 				mlx5dr_dbg(dmn, "Modify header action number exceeds HW limit\n");
 				return -EINVAL;
 			}
@@ -1637,6 +1652,10 @@
 		hw_idx++;
 	}
 
+	/* if the resulting HW actions list is empty, add NOP action */
+	if (!hw_idx)
+		hw_idx++;
+
 	*num_hw_actions = hw_idx;
 
 	return 0;
@@ -1747,7 +1766,7 @@
 
 struct mlx5dr_action *
 mlx5dr_action_create_dest_vport(struct mlx5dr_domain *dmn,
-				u32 vport, u8 vhca_id_valid,
+				u16 vport, u8 vhca_id_valid,
 				u16 vhca_id)
 {
 	struct mlx5dr_cmd_vport_cap *vport_cap;
@@ -1767,9 +1786,11 @@
 		return NULL;
 	}
 
-	vport_cap = mlx5dr_get_vport_cap(&vport_dmn->info.caps, vport);
+	vport_cap = mlx5dr_domain_get_vport_cap(vport_dmn, vport);
 	if (!vport_cap) {
-		mlx5dr_dbg(dmn, "Failed to get vport %d caps\n", vport);
+		mlx5dr_err(dmn,
+			   "Failed to get vport 0x%x caps - vport is disabled or invalid\n",
+			   vport);
 		return NULL;
 	}
 
@@ -1785,7 +1806,7 @@
 
 int mlx5dr_action_destroy(struct mlx5dr_action *action)
 {
-	if (refcount_read(&action->refcount) > 1)
+	if (WARN_ON_ONCE(refcount_read(&action->refcount) > 1))
 		return -EBUSY;
 
 	switch (action->action_type) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_cmd.c
@@ -117,6 +117,8 @@
 	caps->gvmi		= MLX5_CAP_GEN(mdev, vhca_id);
 	caps->flex_protocols	= MLX5_CAP_GEN(mdev, flex_parser_protocols);
 	caps->sw_format_ver	= MLX5_CAP_GEN(mdev, steering_format_version);
+	caps->roce_caps.fl_rc_qp_when_roce_disabled =
+		MLX5_CAP_GEN(mdev, fl_rc_qp_when_roce_disabled);
 
 	if (MLX5_CAP_GEN(mdev, roce)) {
 		err = dr_cmd_query_nic_vport_roce_en(mdev, 0, &roce_en);
@@ -124,7 +126,7 @@
 			return err;
 
 		caps->roce_caps.roce_en = roce_en;
-		caps->roce_caps.fl_rc_qp_when_roce_disabled =
+		caps->roce_caps.fl_rc_qp_when_roce_disabled |=
 			MLX5_CAP_ROCE(mdev, fl_rc_qp_when_roce_disabled);
 		caps->roce_caps.fl_rc_qp_when_roce_enabled =
 			MLX5_CAP_ROCE(mdev, fl_rc_qp_when_roce_enabled);
@@ -132,6 +134,13 @@
 
 	caps->isolate_vl_tc = MLX5_CAP_GEN(mdev, isolate_vl_tc_new);
 
+	/* geneve_tlv_option_0_exist is the indication of
+	 * STE support for lookup type flex_parser_ok
+	 */
+	caps->flex_parser_ok_bits_supp =
+		MLX5_CAP_FLOWTABLE(mdev,
+				   flow_table_properties_nic_receive.ft_field_support.geneve_tlv_option_0_exist);
+
 	if (caps->flex_protocols & MLX5_FLEX_PARSER_ICMP_V4_ENABLED) {
 		caps->flex_parser_id_icmp_dw0 = MLX5_CAP_GEN(mdev, flex_parser_id_icmp_dw0);
 		caps->flex_parser_id_icmp_dw1 = MLX5_CAP_GEN(mdev, flex_parser_id_icmp_dw1);
@@ -152,7 +161,7 @@
 		caps->flex_parser_id_mpls_over_gre =
 			MLX5_CAP_GEN(mdev, flex_parser_id_outer_first_mpls_over_gre);
 
-	if (caps->flex_protocols & mlx5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED)
+	if (caps->flex_protocols & MLX5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED)
 		caps->flex_parser_id_mpls_over_udp =
 			MLX5_CAP_GEN(mdev, flex_parser_id_outer_first_mpls_over_udp_label);
 
@@ -195,6 +204,8 @@
 
 	caps->roce_min_src_udp = MLX5_CAP_ROCE(mdev, r_roce_min_src_udp_port);
 
+	caps->is_ecpf = mlx5_core_is_ecpf_esw_manager(mdev);
+
 	return 0;
 }
 
@@ -272,7 +283,7 @@
 					u32 table_id,
 					u32 group_id,
 					u32 modify_header_id,
-					u32 vport_id)
+					u16 vport)
 {
 	u32 out[MLX5_ST_SZ_DW(set_fte_out)] = {};
 	void *in_flow_context;
@@ -303,7 +314,7 @@
 	in_dests = MLX5_ADDR_OF(flow_context, in_flow_context, destination);
 	MLX5_SET(dest_format_struct, in_dests, destination_type,
 		 MLX5_FLOW_DESTINATION_TYPE_VPORT);
-	MLX5_SET(dest_format_struct, in_dests, destination_id, vport_id);
+	MLX5_SET(dest_format_struct, in_dests, destination_id, vport);
 
 	err = mlx5_cmd_exec(mdev, in, inlen, out, sizeof(out));
 	kvfree(in);
@@ -526,11 +537,12 @@
 
 	err = mlx5_cmd_exec(mdev, in, inlen, out, sizeof(out));
 	if (err)
-		return err;
+		goto err_free_in;
 
 	*reformat_id = MLX5_GET(alloc_packet_reformat_context_out, out, packet_reformat_id);
-	kvfree(in);
 
+err_free_in:
+	kvfree(in);
 	return err;
 }
 
@@ -597,7 +609,8 @@
 	for (i = 0; i < fte->dests_size; i++) {
 		if (fte->dest_arr[i].type == MLX5_FLOW_DESTINATION_TYPE_COUNTER)
 			continue;
-		if (fte->dest_arr[i].type == MLX5_FLOW_DESTINATION_TYPE_VPORT &&
+		if ((fte->dest_arr[i].type == MLX5_FLOW_DESTINATION_TYPE_VPORT ||
+		     fte->dest_arr[i].type == MLX5_FLOW_DESTINATION_TYPE_UPLINK) &&
 		    fte->dest_arr[i].vport.flags & MLX5_FLOW_DEST_VPORT_REFORMAT_ID)
 			num_encap++;
 		num_fwd_destinations++;
@@ -722,12 +735,19 @@
 			case MLX5_FLOW_DESTINATION_TYPE_FLOW_TABLE:
 				id = fte->dest_arr[i].ft_id;
 				break;
+			case MLX5_FLOW_DESTINATION_TYPE_UPLINK:
 			case MLX5_FLOW_DESTINATION_TYPE_VPORT:
-				id = fte->dest_arr[i].vport.num;
-				MLX5_SET(dest_format_struct, in_dests,
-					 destination_eswitch_owner_vhca_id_valid,
-					 !!(fte->dest_arr[i].vport.flags &
-					    MLX5_FLOW_DEST_VPORT_VHCA_ID));
+				if (type == MLX5_FLOW_DESTINATION_TYPE_VPORT) {
+					id = fte->dest_arr[i].vport.num;
+					MLX5_SET(dest_format_struct, in_dests,
+						 destination_eswitch_owner_vhca_id_valid,
+						 !!(fte->dest_arr[i].vport.flags &
+						    MLX5_FLOW_DEST_VPORT_VHCA_ID));
+				} else {
+					id = 0;
+					MLX5_SET(dest_format_struct, in_dests,
+						 destination_eswitch_owner_vhca_id_valid, 1);
+				}
 				MLX5_SET(dest_format_struct, in_dests,
 					 destination_eswitch_owner_vhca_id,
 					 fte->dest_arr[i].vport.vhca_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c
@@ -0,0 +1,649 @@
+// SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB
+// Copyright (c) 2021, NVIDIA CORPORATION & AFFILIATES. All rights reserved.
+
+#include <linux/debugfs.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/seq_file.h>
+#include "dr_types.h"
+
+#define DR_DBG_PTR_TO_ID(p) ((u64)(uintptr_t)(p) & 0xFFFFFFFFULL)
+
+enum dr_dump_rec_type {
+	DR_DUMP_REC_TYPE_DOMAIN = 3000,
+	DR_DUMP_REC_TYPE_DOMAIN_INFO_FLEX_PARSER = 3001,
+	DR_DUMP_REC_TYPE_DOMAIN_INFO_DEV_ATTR = 3002,
+	DR_DUMP_REC_TYPE_DOMAIN_INFO_VPORT = 3003,
+	DR_DUMP_REC_TYPE_DOMAIN_INFO_CAPS = 3004,
+	DR_DUMP_REC_TYPE_DOMAIN_SEND_RING = 3005,
+
+	DR_DUMP_REC_TYPE_TABLE = 3100,
+	DR_DUMP_REC_TYPE_TABLE_RX = 3101,
+	DR_DUMP_REC_TYPE_TABLE_TX = 3102,
+
+	DR_DUMP_REC_TYPE_MATCHER = 3200,
+	DR_DUMP_REC_TYPE_MATCHER_MASK = 3201,
+	DR_DUMP_REC_TYPE_MATCHER_RX = 3202,
+	DR_DUMP_REC_TYPE_MATCHER_TX = 3203,
+	DR_DUMP_REC_TYPE_MATCHER_BUILDER = 3204,
+
+	DR_DUMP_REC_TYPE_RULE = 3300,
+	DR_DUMP_REC_TYPE_RULE_RX_ENTRY_V0 = 3301,
+	DR_DUMP_REC_TYPE_RULE_TX_ENTRY_V0 = 3302,
+	DR_DUMP_REC_TYPE_RULE_RX_ENTRY_V1 = 3303,
+	DR_DUMP_REC_TYPE_RULE_TX_ENTRY_V1 = 3304,
+
+	DR_DUMP_REC_TYPE_ACTION_ENCAP_L2 = 3400,
+	DR_DUMP_REC_TYPE_ACTION_ENCAP_L3 = 3401,
+	DR_DUMP_REC_TYPE_ACTION_MODIFY_HDR = 3402,
+	DR_DUMP_REC_TYPE_ACTION_DROP = 3403,
+	DR_DUMP_REC_TYPE_ACTION_QP = 3404,
+	DR_DUMP_REC_TYPE_ACTION_FT = 3405,
+	DR_DUMP_REC_TYPE_ACTION_CTR = 3406,
+	DR_DUMP_REC_TYPE_ACTION_TAG = 3407,
+	DR_DUMP_REC_TYPE_ACTION_VPORT = 3408,
+	DR_DUMP_REC_TYPE_ACTION_DECAP_L2 = 3409,
+	DR_DUMP_REC_TYPE_ACTION_DECAP_L3 = 3410,
+	DR_DUMP_REC_TYPE_ACTION_DEVX_TIR = 3411,
+	DR_DUMP_REC_TYPE_ACTION_PUSH_VLAN = 3412,
+	DR_DUMP_REC_TYPE_ACTION_POP_VLAN = 3413,
+	DR_DUMP_REC_TYPE_ACTION_SAMPLER = 3415,
+	DR_DUMP_REC_TYPE_ACTION_INSERT_HDR = 3420,
+	DR_DUMP_REC_TYPE_ACTION_REMOVE_HDR = 3421
+};
+
+void mlx5dr_dbg_tbl_add(struct mlx5dr_table *tbl)
+{
+	mutex_lock(&tbl->dmn->dump_info.dbg_mutex);
+	list_add_tail(&tbl->dbg_node, &tbl->dmn->dbg_tbl_list);
+	mutex_unlock(&tbl->dmn->dump_info.dbg_mutex);
+}
+
+void mlx5dr_dbg_tbl_del(struct mlx5dr_table *tbl)
+{
+	mutex_lock(&tbl->dmn->dump_info.dbg_mutex);
+	list_del(&tbl->dbg_node);
+	mutex_unlock(&tbl->dmn->dump_info.dbg_mutex);
+}
+
+void mlx5dr_dbg_rule_add(struct mlx5dr_rule *rule)
+{
+	struct mlx5dr_domain *dmn = rule->matcher->tbl->dmn;
+
+	mutex_lock(&dmn->dump_info.dbg_mutex);
+	list_add_tail(&rule->dbg_node, &rule->matcher->dbg_rule_list);
+	mutex_unlock(&dmn->dump_info.dbg_mutex);
+}
+
+void mlx5dr_dbg_rule_del(struct mlx5dr_rule *rule)
+{
+	struct mlx5dr_domain *dmn = rule->matcher->tbl->dmn;
+
+	mutex_lock(&dmn->dump_info.dbg_mutex);
+	list_del(&rule->dbg_node);
+	mutex_unlock(&dmn->dump_info.dbg_mutex);
+}
+
+static u64 dr_dump_icm_to_idx(u64 icm_addr)
+{
+	return (icm_addr >> 6) & 0xffffffff;
+}
+
+#define DR_HEX_SIZE 256
+
+static void
+dr_dump_hex_print(char hex[DR_HEX_SIZE], char *src, u32 size)
+{
+	if (WARN_ON_ONCE(DR_HEX_SIZE < 2 * size + 1))
+		size = DR_HEX_SIZE / 2 - 1; /* truncate */
+
+	bin2hex(hex, src, size);
+	hex[2 * size] = 0; /* NULL-terminate */
+}
+
+static int
+dr_dump_rule_action_mem(struct seq_file *file, const u64 rule_id,
+			struct mlx5dr_rule_action_member *action_mem)
+{
+	struct mlx5dr_action *action = action_mem->action;
+	const u64 action_id = DR_DBG_PTR_TO_ID(action);
+
+	switch (action->action_type) {
+	case DR_ACTION_TYP_DROP:
+		seq_printf(file, "%d,0x%llx,0x%llx\n",
+			   DR_DUMP_REC_TYPE_ACTION_DROP, action_id, rule_id);
+		break;
+	case DR_ACTION_TYP_FT:
+		if (action->dest_tbl->is_fw_tbl)
+			seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+				   DR_DUMP_REC_TYPE_ACTION_FT, action_id,
+				   rule_id, action->dest_tbl->fw_tbl.id);
+		else
+			seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+				   DR_DUMP_REC_TYPE_ACTION_FT, action_id,
+				   rule_id, action->dest_tbl->tbl->table_id);
+
+		break;
+	case DR_ACTION_TYP_CTR:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_CTR, action_id, rule_id,
+			   action->ctr->ctr_id + action->ctr->offset);
+		break;
+	case DR_ACTION_TYP_TAG:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_TAG, action_id, rule_id,
+			   action->flow_tag->flow_tag);
+		break;
+	case DR_ACTION_TYP_MODIFY_HDR:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_MODIFY_HDR, action_id,
+			   rule_id, action->rewrite->index);
+		break;
+	case DR_ACTION_TYP_VPORT:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_VPORT, action_id, rule_id,
+			   action->vport->caps->num);
+		break;
+	case DR_ACTION_TYP_TNL_L2_TO_L2:
+		seq_printf(file, "%d,0x%llx,0x%llx\n",
+			   DR_DUMP_REC_TYPE_ACTION_DECAP_L2, action_id,
+			   rule_id);
+		break;
+	case DR_ACTION_TYP_TNL_L3_TO_L2:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_DECAP_L3, action_id,
+			   rule_id, action->rewrite->index);
+		break;
+	case DR_ACTION_TYP_L2_TO_TNL_L2:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_ENCAP_L2, action_id,
+			   rule_id, action->reformat->id);
+		break;
+	case DR_ACTION_TYP_L2_TO_TNL_L3:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_ENCAP_L3, action_id,
+			   rule_id, action->reformat->id);
+		break;
+	case DR_ACTION_TYP_POP_VLAN:
+		seq_printf(file, "%d,0x%llx,0x%llx\n",
+			   DR_DUMP_REC_TYPE_ACTION_POP_VLAN, action_id,
+			   rule_id);
+		break;
+	case DR_ACTION_TYP_PUSH_VLAN:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_PUSH_VLAN, action_id,
+			   rule_id, action->push_vlan->vlan_hdr);
+		break;
+	case DR_ACTION_TYP_INSERT_HDR:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x,0x%x,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_INSERT_HDR, action_id,
+			   rule_id, action->reformat->id,
+			   action->reformat->param_0,
+			   action->reformat->param_1);
+		break;
+	case DR_ACTION_TYP_REMOVE_HDR:
+		seq_printf(file, "%d,0x%llx,0x%llx,0x%x,0x%x,0x%x\n",
+			   DR_DUMP_REC_TYPE_ACTION_REMOVE_HDR, action_id,
+			   rule_id, action->reformat->id,
+			   action->reformat->param_0,
+			   action->reformat->param_1);
+		break;
+	case DR_ACTION_TYP_SAMPLER:
+		seq_printf(file,
+			   "%d,0x%llx,0x%llx,0x%x,0x%x,0x%x,0x%llx,0x%llx\n",
+			   DR_DUMP_REC_TYPE_ACTION_SAMPLER, action_id, rule_id,
+			   0, 0, action->sampler->sampler_id,
+			   action->sampler->rx_icm_addr,
+			   action->sampler->tx_icm_addr);
+		break;
+	default:
+		return 0;
+	}
+
+	return 0;
+}
+
+static int
+dr_dump_rule_mem(struct seq_file *file, struct mlx5dr_ste *ste,
+		 bool is_rx, const u64 rule_id, u8 format_ver)
+{
+	char hw_ste_dump[DR_HEX_SIZE];
+	u32 mem_rec_type;
+
+	if (format_ver == MLX5_STEERING_FORMAT_CONNECTX_5) {
+		mem_rec_type = is_rx ? DR_DUMP_REC_TYPE_RULE_RX_ENTRY_V0 :
+				       DR_DUMP_REC_TYPE_RULE_TX_ENTRY_V0;
+	} else {
+		mem_rec_type = is_rx ? DR_DUMP_REC_TYPE_RULE_RX_ENTRY_V1 :
+				       DR_DUMP_REC_TYPE_RULE_TX_ENTRY_V1;
+	}
+
+	dr_dump_hex_print(hw_ste_dump, (char *)ste->hw_ste, DR_STE_SIZE_REDUCED);
+
+	seq_printf(file, "%d,0x%llx,0x%llx,%s\n", mem_rec_type,
+		   dr_dump_icm_to_idx(mlx5dr_ste_get_icm_addr(ste)), rule_id,
+		   hw_ste_dump);
+
+	return 0;
+}
+
+static int
+dr_dump_rule_rx_tx(struct seq_file *file, struct mlx5dr_rule_rx_tx *rule_rx_tx,
+		   bool is_rx, const u64 rule_id, u8 format_ver)
+{
+	struct mlx5dr_ste *ste_arr[DR_RULE_MAX_STES + DR_ACTION_MAX_STES];
+	struct mlx5dr_ste *curr_ste = rule_rx_tx->last_rule_ste;
+	int ret, i;
+
+	if (mlx5dr_rule_get_reverse_rule_members(ste_arr, curr_ste, &i))
+		return 0;
+
+	while (i--) {
+		ret = dr_dump_rule_mem(file, ste_arr[i], is_rx, rule_id,
+				       format_ver);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int dr_dump_rule(struct seq_file *file, struct mlx5dr_rule *rule)
+{
+	struct mlx5dr_rule_action_member *action_mem;
+	const u64 rule_id = DR_DBG_PTR_TO_ID(rule);
+	struct mlx5dr_rule_rx_tx *rx = &rule->rx;
+	struct mlx5dr_rule_rx_tx *tx = &rule->tx;
+	u8 format_ver;
+	int ret;
+
+	format_ver = rule->matcher->tbl->dmn->info.caps.sw_format_ver;
+
+	seq_printf(file, "%d,0x%llx,0x%llx\n", DR_DUMP_REC_TYPE_RULE, rule_id,
+		   DR_DBG_PTR_TO_ID(rule->matcher));
+
+	if (rx->nic_matcher) {
+		ret = dr_dump_rule_rx_tx(file, rx, true, rule_id, format_ver);
+		if (ret < 0)
+			return ret;
+	}
+
+	if (tx->nic_matcher) {
+		ret = dr_dump_rule_rx_tx(file, tx, false, rule_id, format_ver);
+		if (ret < 0)
+			return ret;
+	}
+
+	list_for_each_entry(action_mem, &rule->rule_actions_list, list) {
+		ret = dr_dump_rule_action_mem(file, rule_id, action_mem);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int
+dr_dump_matcher_mask(struct seq_file *file, struct mlx5dr_match_param *mask,
+		     u8 criteria, const u64 matcher_id)
+{
+	char dump[DR_HEX_SIZE];
+
+	seq_printf(file, "%d,0x%llx,", DR_DUMP_REC_TYPE_MATCHER_MASK,
+		   matcher_id);
+
+	if (criteria & DR_MATCHER_CRITERIA_OUTER) {
+		dr_dump_hex_print(dump, (char *)&mask->outer, sizeof(mask->outer));
+		seq_printf(file, "%s,", dump);
+	} else {
+		seq_puts(file, ",");
+	}
+
+	if (criteria & DR_MATCHER_CRITERIA_INNER) {
+		dr_dump_hex_print(dump, (char *)&mask->inner, sizeof(mask->inner));
+		seq_printf(file, "%s,", dump);
+	} else {
+		seq_puts(file, ",");
+	}
+
+	if (criteria & DR_MATCHER_CRITERIA_MISC) {
+		dr_dump_hex_print(dump, (char *)&mask->misc, sizeof(mask->misc));
+		seq_printf(file, "%s,", dump);
+	} else {
+		seq_puts(file, ",");
+	}
+
+	if (criteria & DR_MATCHER_CRITERIA_MISC2) {
+		dr_dump_hex_print(dump, (char *)&mask->misc2, sizeof(mask->misc2));
+		seq_printf(file, "%s,", dump);
+	} else {
+		seq_puts(file, ",");
+	}
+
+	if (criteria & DR_MATCHER_CRITERIA_MISC3) {
+		dr_dump_hex_print(dump, (char *)&mask->misc3, sizeof(mask->misc3));
+		seq_printf(file, "%s\n", dump);
+	} else {
+		seq_puts(file, ",\n");
+	}
+
+	return 0;
+}
+
+static int
+dr_dump_matcher_builder(struct seq_file *file, struct mlx5dr_ste_build *builder,
+			u32 index, bool is_rx, const u64 matcher_id)
+{
+	seq_printf(file, "%d,0x%llx,%d,%d,0x%x\n",
+		   DR_DUMP_REC_TYPE_MATCHER_BUILDER, matcher_id, index, is_rx,
+		   builder->lu_type);
+
+	return 0;
+}
+
+static int
+dr_dump_matcher_rx_tx(struct seq_file *file, bool is_rx,
+		      struct mlx5dr_matcher_rx_tx *matcher_rx_tx,
+		      const u64 matcher_id)
+{
+	enum dr_dump_rec_type rec_type;
+	int i, ret;
+
+	rec_type = is_rx ? DR_DUMP_REC_TYPE_MATCHER_RX :
+			   DR_DUMP_REC_TYPE_MATCHER_TX;
+
+	seq_printf(file, "%d,0x%llx,0x%llx,%d,0x%llx,0x%llx\n",
+		   rec_type, DR_DBG_PTR_TO_ID(matcher_rx_tx),
+		   matcher_id, matcher_rx_tx->num_of_builders,
+		   dr_dump_icm_to_idx(matcher_rx_tx->s_htbl->chunk->icm_addr),
+		   dr_dump_icm_to_idx(matcher_rx_tx->e_anchor->chunk->icm_addr));
+
+	for (i = 0; i < matcher_rx_tx->num_of_builders; i++) {
+		ret = dr_dump_matcher_builder(file,
+					      &matcher_rx_tx->ste_builder[i],
+					      i, is_rx, matcher_id);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int
+dr_dump_matcher(struct seq_file *file, struct mlx5dr_matcher *matcher)
+{
+	struct mlx5dr_matcher_rx_tx *rx = &matcher->rx;
+	struct mlx5dr_matcher_rx_tx *tx = &matcher->tx;
+	u64 matcher_id;
+	int ret;
+
+	matcher_id = DR_DBG_PTR_TO_ID(matcher);
+
+	seq_printf(file, "%d,0x%llx,0x%llx,%d\n", DR_DUMP_REC_TYPE_MATCHER,
+		   matcher_id, DR_DBG_PTR_TO_ID(matcher->tbl), matcher->prio);
+
+	ret = dr_dump_matcher_mask(file, &matcher->mask,
+				   matcher->match_criteria, matcher_id);
+	if (ret < 0)
+		return ret;
+
+	if (rx->nic_tbl) {
+		ret = dr_dump_matcher_rx_tx(file, true, rx, matcher_id);
+		if (ret < 0)
+			return ret;
+	}
+
+	if (tx->nic_tbl) {
+		ret = dr_dump_matcher_rx_tx(file, false, tx, matcher_id);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int
+dr_dump_matcher_all(struct seq_file *file, struct mlx5dr_matcher *matcher)
+{
+	struct mlx5dr_rule *rule;
+	int ret;
+
+	ret = dr_dump_matcher(file, matcher);
+	if (ret < 0)
+		return ret;
+
+	list_for_each_entry(rule, &matcher->dbg_rule_list, dbg_node) {
+		ret = dr_dump_rule(file, rule);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int
+dr_dump_table_rx_tx(struct seq_file *file, bool is_rx,
+		    struct mlx5dr_table_rx_tx *table_rx_tx,
+		    const u64 table_id)
+{
+	enum dr_dump_rec_type rec_type;
+
+	rec_type = is_rx ? DR_DUMP_REC_TYPE_TABLE_RX :
+			   DR_DUMP_REC_TYPE_TABLE_TX;
+
+	seq_printf(file, "%d,0x%llx,0x%llx\n", rec_type, table_id,
+		   dr_dump_icm_to_idx(table_rx_tx->s_anchor->chunk->icm_addr));
+
+	return 0;
+}
+
+static int dr_dump_table(struct seq_file *file, struct mlx5dr_table *table)
+{
+	struct mlx5dr_table_rx_tx *rx = &table->rx;
+	struct mlx5dr_table_rx_tx *tx = &table->tx;
+	int ret;
+
+	seq_printf(file, "%d,0x%llx,0x%llx,%d,%d\n", DR_DUMP_REC_TYPE_TABLE,
+		   DR_DBG_PTR_TO_ID(table), DR_DBG_PTR_TO_ID(table->dmn),
+		   table->table_type, table->level);
+
+	if (rx->nic_dmn) {
+		ret = dr_dump_table_rx_tx(file, true, rx,
+					  DR_DBG_PTR_TO_ID(table));
+		if (ret < 0)
+			return ret;
+	}
+
+	if (tx->nic_dmn) {
+		ret = dr_dump_table_rx_tx(file, false, tx,
+					  DR_DBG_PTR_TO_ID(table));
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+static int dr_dump_table_all(struct seq_file *file, struct mlx5dr_table *tbl)
+{
+	struct mlx5dr_matcher *matcher;
+	int ret;
+
+	ret = dr_dump_table(file, tbl);
+	if (ret < 0)
+		return ret;
+
+	list_for_each_entry(matcher, &tbl->matcher_list, list_node) {
+		ret = dr_dump_matcher_all(file, matcher);
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+static int
+dr_dump_send_ring(struct seq_file *file, struct mlx5dr_send_ring *ring,
+		  const u64 domain_id)
+{
+	seq_printf(file, "%d,0x%llx,0x%llx,0x%x,0x%x\n",
+		   DR_DUMP_REC_TYPE_DOMAIN_SEND_RING, DR_DBG_PTR_TO_ID(ring),
+		   domain_id, ring->cq->mcq.cqn, ring->qp->qpn);
+	return 0;
+}
+
+static int
+dr_dump_domain_info_flex_parser(struct seq_file *file,
+				const char *flex_parser_name,
+				const u8 flex_parser_value,
+				const u64 domain_id)
+{
+	seq_printf(file, "%d,0x%llx,%s,0x%x\n",
+		   DR_DUMP_REC_TYPE_DOMAIN_INFO_FLEX_PARSER, domain_id,
+		   flex_parser_name, flex_parser_value);
+	return 0;
+}
+
+static int
+dr_dump_domain_info_caps(struct seq_file *file, struct mlx5dr_cmd_caps *caps,
+			 const u64 domain_id)
+{
+	struct mlx5dr_cmd_vport_cap *vport_caps;
+	unsigned long i, vports_num;
+
+	xa_for_each(&caps->vports.vports_caps_xa, vports_num, vport_caps)
+		; /* count the number of vports in xarray */
+
+	seq_printf(file, "%d,0x%llx,0x%x,0x%llx,0x%llx,0x%x,%lu,%d\n",
+		   DR_DUMP_REC_TYPE_DOMAIN_INFO_CAPS, domain_id, caps->gvmi,
+		   caps->nic_rx_drop_address, caps->nic_tx_drop_address,
+		   caps->flex_protocols, vports_num, caps->eswitch_manager);
+
+	xa_for_each(&caps->vports.vports_caps_xa, i, vport_caps) {
+		vport_caps = xa_load(&caps->vports.vports_caps_xa, i);
+
+		seq_printf(file, "%d,0x%llx,%lu,0x%x,0x%llx,0x%llx\n",
+			   DR_DUMP_REC_TYPE_DOMAIN_INFO_VPORT, domain_id, i,
+			   vport_caps->vport_gvmi, vport_caps->icm_address_rx,
+			   vport_caps->icm_address_tx);
+	}
+	return 0;
+}
+
+static int
+dr_dump_domain_info(struct seq_file *file, struct mlx5dr_domain_info *info,
+		    const u64 domain_id)
+{
+	int ret;
+
+	ret = dr_dump_domain_info_caps(file, &info->caps, domain_id);
+	if (ret < 0)
+		return ret;
+
+	ret = dr_dump_domain_info_flex_parser(file, "icmp_dw0",
+					      info->caps.flex_parser_id_icmp_dw0,
+					      domain_id);
+	if (ret < 0)
+		return ret;
+
+	ret = dr_dump_domain_info_flex_parser(file, "icmp_dw1",
+					      info->caps.flex_parser_id_icmp_dw1,
+					      domain_id);
+	if (ret < 0)
+		return ret;
+
+	ret = dr_dump_domain_info_flex_parser(file, "icmpv6_dw0",
+					      info->caps.flex_parser_id_icmpv6_dw0,
+					      domain_id);
+	if (ret < 0)
+		return ret;
+
+	ret = dr_dump_domain_info_flex_parser(file, "icmpv6_dw1",
+					      info->caps.flex_parser_id_icmpv6_dw1,
+					      domain_id);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int
+dr_dump_domain(struct seq_file *file, struct mlx5dr_domain *dmn)
+{
+	u64 domain_id = DR_DBG_PTR_TO_ID(dmn);
+	int ret;
+
+	seq_printf(file, "%d,0x%llx,%d,0%x,%d,%s\n", DR_DUMP_REC_TYPE_DOMAIN,
+		   domain_id, dmn->type, dmn->info.caps.gvmi,
+		   dmn->info.supp_sw_steering, pci_name(dmn->mdev->pdev));
+
+	ret = dr_dump_domain_info(file, &dmn->info, domain_id);
+	if (ret < 0)
+		return ret;
+
+	if (dmn->info.supp_sw_steering) {
+		ret = dr_dump_send_ring(file, dmn->send_ring, domain_id);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int dr_dump_domain_all(struct seq_file *file, struct mlx5dr_domain *dmn)
+{
+	struct mlx5dr_table *tbl;
+	int ret;
+
+	mutex_lock(&dmn->dump_info.dbg_mutex);
+	mlx5dr_domain_lock(dmn);
+
+	ret = dr_dump_domain(file, dmn);
+	if (ret < 0)
+		goto unlock_mutex;
+
+	list_for_each_entry(tbl, &dmn->dbg_tbl_list, dbg_node) {
+		ret = dr_dump_table_all(file, tbl);
+		if (ret < 0)
+			break;
+	}
+
+unlock_mutex:
+	mlx5dr_domain_unlock(dmn);
+	mutex_unlock(&dmn->dump_info.dbg_mutex);
+	return ret;
+}
+
+static int dr_dump_show(struct seq_file *file, void *priv)
+{
+	return dr_dump_domain_all(file, file->private);
+}
+DEFINE_SHOW_ATTRIBUTE(dr_dump);
+
+void mlx5dr_dbg_init_dump(struct mlx5dr_domain *dmn)
+{
+	struct mlx5_core_dev *dev = dmn->mdev;
+	char file_name[128];
+
+	if (dmn->type != MLX5DR_DOMAIN_TYPE_FDB) {
+		mlx5_core_warn(dev,
+			       "Steering dump is not supported for NIC RX/TX domains\n");
+		return;
+	}
+
+	dmn->dump_info.steering_debugfs =
+		debugfs_create_dir("steering", dev->priv.dbg_root);
+	dmn->dump_info.fdb_debugfs =
+		debugfs_create_dir("fdb", dmn->dump_info.steering_debugfs);
+
+	sprintf(file_name, "dmn_%p", dmn);
+	debugfs_create_file(file_name, 0444, dmn->dump_info.fdb_debugfs,
+			    dmn, &dr_dump_fops);
+
+	INIT_LIST_HEAD(&dmn->dbg_tbl_list);
+	mutex_init(&dmn->dump_info.dbg_mutex);
+}
+
+void mlx5dr_dbg_uninit_dump(struct mlx5dr_domain *dmn)
+{
+	debugfs_remove_recursive(dmn->dump_info.steering_debugfs);
+	mutex_destroy(&dmn->dump_info.dbg_mutex);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB */
+/* Copyright (c) 2021, NVIDIA CORPORATION & AFFILIATES. All rights reserved. */
+
+struct mlx5dr_dbg_dump_info {
+	struct mutex dbg_mutex; /* protect dbg lists */
+	struct dentry *steering_debugfs;
+	struct dentry *fdb_debugfs;
+};
+
+void mlx5dr_dbg_init_dump(struct mlx5dr_domain *dmn);
+void mlx5dr_dbg_uninit_dump(struct mlx5dr_domain *dmn);
+void mlx5dr_dbg_tbl_add(struct mlx5dr_table *tbl);
+void mlx5dr_dbg_tbl_del(struct mlx5dr_table *tbl);
+void mlx5dr_dbg_rule_add(struct mlx5dr_rule *rule);
+void mlx5dr_dbg_rule_del(struct mlx5dr_rule *rule);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_domain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_domain.c
@@ -2,55 +2,53 @@
 /* Copyright (c) 2019 Mellanox Technologies. */
 
 #include <linux/mlx5/eswitch.h>
+#include <linux/err.h>
 #include "dr_types.h"
 
 #define DR_DOMAIN_SW_STEERING_SUPPORTED(dmn, dmn_type)	\
 	((dmn)->info.caps.dmn_type##_sw_owner ||	\
 	 ((dmn)->info.caps.dmn_type##_sw_owner_v2 &&	\
-	  (dmn)->info.caps.sw_format_ver <= MLX5_STEERING_FORMAT_CONNECTX_6DX))
+	  (dmn)->info.caps.sw_format_ver <= MLX5_STEERING_FORMAT_CONNECTX_7))
 
-static int dr_domain_init_cache(struct mlx5dr_domain *dmn)
+static void dr_domain_init_csum_recalc_fts(struct mlx5dr_domain *dmn)
 {
 	/* Per vport cached FW FT for checksum recalculation, this
-	 * recalculation is needed due to a HW bug.
+	 * recalculation is needed due to a HW bug in STEv0.
 	 */
-	dmn->cache.recalc_cs_ft = kcalloc(dmn->info.caps.num_vports,
-					  sizeof(dmn->cache.recalc_cs_ft[0]),
-					  GFP_KERNEL);
-	if (!dmn->cache.recalc_cs_ft)
-		return -ENOMEM;
-
-	return 0;
+	xa_init(&dmn->csum_fts_xa);
 }
 
-static void dr_domain_uninit_cache(struct mlx5dr_domain *dmn)
+static void dr_domain_uninit_csum_recalc_fts(struct mlx5dr_domain *dmn)
 {
-	int i;
-
-	for (i = 0; i < dmn->info.caps.num_vports; i++) {
-		if (!dmn->cache.recalc_cs_ft[i])
-			continue;
+	struct mlx5dr_fw_recalc_cs_ft *recalc_cs_ft;
+	unsigned long i;
 
-		mlx5dr_fw_destroy_recalc_cs_ft(dmn, dmn->cache.recalc_cs_ft[i]);
+	xa_for_each(&dmn->csum_fts_xa, i, recalc_cs_ft) {
+		if (recalc_cs_ft)
+			mlx5dr_fw_destroy_recalc_cs_ft(dmn, recalc_cs_ft);
 	}
 
-	kfree(dmn->cache.recalc_cs_ft);
+	xa_destroy(&dmn->csum_fts_xa);
 }
 
-int mlx5dr_domain_cache_get_recalc_cs_ft_addr(struct mlx5dr_domain *dmn,
-					      u32 vport_num,
-					      u64 *rx_icm_addr)
+int mlx5dr_domain_get_recalc_cs_ft_addr(struct mlx5dr_domain *dmn,
+					u16 vport_num,
+					u64 *rx_icm_addr)
 {
 	struct mlx5dr_fw_recalc_cs_ft *recalc_cs_ft;
+	int ret;
 
-	recalc_cs_ft = dmn->cache.recalc_cs_ft[vport_num];
+	recalc_cs_ft = xa_load(&dmn->csum_fts_xa, vport_num);
 	if (!recalc_cs_ft) {
-		/* Table not in cache, need to allocate a new one */
+		/* Table hasn't been created yet */
 		recalc_cs_ft = mlx5dr_fw_create_recalc_cs_ft(dmn, vport_num);
 		if (!recalc_cs_ft)
 			return -EINVAL;
 
-		dmn->cache.recalc_cs_ft[vport_num] = recalc_cs_ft;
+		ret = xa_err(xa_store(&dmn->csum_fts_xa, vport_num,
+				      recalc_cs_ft, GFP_KERNEL));
+		if (ret)
+			return ret;
 	}
 
 	*rx_icm_addr = recalc_cs_ft->rx_icm_addr;
@@ -75,9 +73,9 @@
 	}
 
 	dmn->uar = mlx5_get_uars_page(dmn->mdev);
-	if (!dmn->uar) {
+	if (IS_ERR(dmn->uar)) {
 		mlx5dr_err(dmn, "Couldn't allocate UAR\n");
-		ret = -ENOMEM;
+		ret = PTR_ERR(dmn->uar);
 		goto clean_pd;
 	}
 
@@ -124,15 +122,25 @@
 	mlx5_core_dealloc_pd(dmn->mdev, dmn->pdn);
 }
 
+static void dr_domain_fill_uplink_caps(struct mlx5dr_domain *dmn,
+				       struct mlx5dr_cmd_vport_cap *uplink_vport)
+{
+	struct mlx5dr_esw_caps *esw_caps = &dmn->info.caps.esw_caps;
+
+	uplink_vport->num = MLX5_VPORT_UPLINK;
+	uplink_vport->icm_address_rx = esw_caps->uplink_icm_address_rx;
+	uplink_vport->icm_address_tx = esw_caps->uplink_icm_address_tx;
+	uplink_vport->vport_gvmi = 0;
+	uplink_vport->vhca_gvmi = dmn->info.caps.gvmi;
+}
+
 static int dr_domain_query_vport(struct mlx5dr_domain *dmn,
+				 u16 vport_number,
 				 bool other_vport,
-				 u16 vport_number)
+				 struct mlx5dr_cmd_vport_cap *vport_caps)
 {
-	struct mlx5dr_cmd_vport_cap *vport_caps;
 	int ret;
 
-	vport_caps = &dmn->info.caps.vports_caps[vport_number];
-
 	ret = mlx5dr_cmd_query_esw_vport_context(dmn->mdev,
 						 other_vport,
 						 vport_number,
@@ -154,29 +162,87 @@
 	return 0;
 }
 
-static int dr_domain_query_vports(struct mlx5dr_domain *dmn)
+static int dr_domain_query_esw_mngr(struct mlx5dr_domain *dmn)
 {
-	struct mlx5dr_esw_caps *esw_caps = &dmn->info.caps.esw_caps;
-	struct mlx5dr_cmd_vport_cap *wire_vport;
-	int vport;
+	return dr_domain_query_vport(dmn, 0, false,
+				     &dmn->info.caps.vports.esw_manager_caps);
+}
+
+static void dr_domain_query_uplink(struct mlx5dr_domain *dmn)
+{
+	dr_domain_fill_uplink_caps(dmn, &dmn->info.caps.vports.uplink_caps);
+}
+
+static struct mlx5dr_cmd_vport_cap *
+dr_domain_add_vport_cap(struct mlx5dr_domain *dmn, u16 vport)
+{
+	struct mlx5dr_cmd_caps *caps = &dmn->info.caps;
+	struct mlx5dr_cmd_vport_cap *vport_caps;
 	int ret;
 
-	/* Query vports (except wire vport) */
-	for (vport = 0; vport < dmn->info.caps.num_esw_ports - 1; vport++) {
-		ret = dr_domain_query_vport(dmn, !!vport, vport);
-		if (ret)
-			return ret;
+	vport_caps = kvzalloc(sizeof(*vport_caps), GFP_KERNEL);
+	if (!vport_caps)
+		return NULL;
+
+	ret = dr_domain_query_vport(dmn, vport, true, vport_caps);
+	if (ret) {
+		kvfree(vport_caps);
+		return NULL;
+	}
+
+	ret = xa_insert(&caps->vports.vports_caps_xa, vport,
+			vport_caps, GFP_KERNEL);
+	if (ret) {
+		mlx5dr_dbg(dmn, "Couldn't insert new vport into xarray (%d)\n", ret);
+		kvfree(vport_caps);
+		return ERR_PTR(ret);
 	}
 
-	/* Last vport is the wire port */
-	wire_vport = &dmn->info.caps.vports_caps[vport];
-	wire_vport->num = WIRE_PORT;
-	wire_vport->icm_address_rx = esw_caps->uplink_icm_address_rx;
-	wire_vport->icm_address_tx = esw_caps->uplink_icm_address_tx;
-	wire_vport->vport_gvmi = 0;
-	wire_vport->vhca_gvmi = dmn->info.caps.gvmi;
+	return vport_caps;
+}
 
-	return 0;
+static bool dr_domain_is_esw_mgr_vport(struct mlx5dr_domain *dmn, u16 vport)
+{
+	struct mlx5dr_cmd_caps *caps = &dmn->info.caps;
+
+	return (caps->is_ecpf && vport == MLX5_VPORT_ECPF) ||
+	       (!caps->is_ecpf && vport == 0);
+}
+
+struct mlx5dr_cmd_vport_cap *
+mlx5dr_domain_get_vport_cap(struct mlx5dr_domain *dmn, u16 vport)
+{
+	struct mlx5dr_cmd_caps *caps = &dmn->info.caps;
+	struct mlx5dr_cmd_vport_cap *vport_caps;
+
+	if (dr_domain_is_esw_mgr_vport(dmn, vport))
+		return &caps->vports.esw_manager_caps;
+
+	if (vport == MLX5_VPORT_UPLINK)
+		return &caps->vports.uplink_caps;
+
+vport_load:
+	vport_caps = xa_load(&caps->vports.vports_caps_xa, vport);
+	if (vport_caps)
+		return vport_caps;
+
+	vport_caps = dr_domain_add_vport_cap(dmn, vport);
+	if (PTR_ERR(vport_caps) == -EBUSY)
+		/* caps were already stored by another thread */
+		goto vport_load;
+
+	return vport_caps;
+}
+
+static void dr_domain_clear_vports(struct mlx5dr_domain *dmn)
+{
+	struct mlx5dr_cmd_vport_cap *vport_caps;
+	unsigned long i;
+
+	xa_for_each(&dmn->info.caps.vports.vports_caps_xa, i, vport_caps) {
+		vport_caps = xa_erase(&dmn->info.caps.vports.vports_caps_xa, i);
+		kvfree(vport_caps);
+	}
 }
 
 static int dr_domain_query_fdb_caps(struct mlx5_core_dev *mdev,
@@ -196,25 +262,25 @@
 	dmn->info.caps.esw_rx_drop_address = dmn->info.caps.esw_caps.drop_icm_address_rx;
 	dmn->info.caps.esw_tx_drop_address = dmn->info.caps.esw_caps.drop_icm_address_tx;
 
-	dmn->info.caps.vports_caps = kcalloc(dmn->info.caps.num_esw_ports,
-					     sizeof(dmn->info.caps.vports_caps[0]),
-					     GFP_KERNEL);
-	if (!dmn->info.caps.vports_caps)
-		return -ENOMEM;
+	xa_init(&dmn->info.caps.vports.vports_caps_xa);
+
+	/* Query eswitch manager and uplink vports only. Rest of the
+	 * vports (vport 0, VFs and SFs) will be queried dynamically.
+	 */
 
-	ret = dr_domain_query_vports(dmn);
+	ret = dr_domain_query_esw_mngr(dmn);
 	if (ret) {
-		mlx5dr_err(dmn, "Failed to query vports caps (err: %d)", ret);
-		goto free_vports_caps;
+		mlx5dr_err(dmn, "Failed to query eswitch manager vport caps (err: %d)", ret);
+		goto free_vports_caps_xa;
 	}
 
-	dmn->info.caps.num_vports = dmn->info.caps.num_esw_ports - 1;
+	dr_domain_query_uplink(dmn);
 
 	return 0;
 
-free_vports_caps:
-	kfree(dmn->info.caps.vports_caps);
-	dmn->info.caps.vports_caps = NULL;
+free_vports_caps_xa:
+	xa_destroy(&dmn->info.caps.vports.vports_caps_xa);
+
 	return ret;
 }
 
@@ -229,8 +295,6 @@
 		return -EOPNOTSUPP;
 	}
 
-	dmn->info.caps.num_esw_ports = mlx5_eswitch_get_total_vports(mdev);
-
 	ret = mlx5dr_cmd_query_device(mdev, &dmn->info.caps);
 	if (ret)
 		return ret;
@@ -267,11 +331,7 @@
 
 		dmn->info.rx.type = DR_DOMAIN_NIC_TYPE_RX;
 		dmn->info.tx.type = DR_DOMAIN_NIC_TYPE_TX;
-		vport_cap = mlx5dr_get_vport_cap(&dmn->info.caps, 0);
-		if (!vport_cap) {
-			mlx5dr_err(dmn, "Failed to get esw manager vport\n");
-			return -ENOENT;
-		}
+		vport_cap = &dmn->info.caps.vports.esw_manager_caps;
 
 		dmn->info.supp_sw_steering = true;
 		dmn->info.tx.default_icm_addr = vport_cap->icm_address_tx;
@@ -290,7 +350,8 @@
 
 static void dr_domain_caps_uninit(struct mlx5dr_domain *dmn)
 {
-	kfree(dmn->info.caps.vports_caps);
+	dr_domain_clear_vports(dmn);
+	xa_destroy(&dmn->info.caps.vports.vports_caps_xa);
 }
 
 struct mlx5dr_domain *
@@ -333,16 +394,10 @@
 		goto uninit_caps;
 	}
 
-	ret = dr_domain_init_cache(dmn);
-	if (ret) {
-		mlx5dr_err(dmn, "Failed initialize domain cache\n");
-		goto uninit_resourses;
-	}
-
+	dr_domain_init_csum_recalc_fts(dmn);
+	mlx5dr_dbg_init_dump(dmn);
 	return dmn;
 
-uninit_resourses:
-	dr_domain_uninit_resources(dmn);
 uninit_caps:
 	dr_domain_caps_uninit(dmn);
 free_domain:
@@ -376,12 +431,13 @@
 
 int mlx5dr_domain_destroy(struct mlx5dr_domain *dmn)
 {
-	if (refcount_read(&dmn->refcount) > 1)
+	if (WARN_ON_ONCE(refcount_read(&dmn->refcount) > 1))
 		return -EBUSY;
 
 	/* make sure resources are not used by the hardware */
 	mlx5dr_cmd_sync_steering(dmn->mdev);
-	dr_domain_uninit_cache(dmn);
+	mlx5dr_dbg_uninit_dump(dmn);
+	dr_domain_uninit_csum_recalc_fts(dmn);
 	dr_domain_uninit_resources(dmn);
 	dr_domain_caps_uninit(dmn);
 	mutex_destroy(&dmn->info.tx.mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_fw.c
@@ -5,7 +5,7 @@
 #include "dr_types.h"
 
 struct mlx5dr_fw_recalc_cs_ft *
-mlx5dr_fw_create_recalc_cs_ft(struct mlx5dr_domain *dmn, u32 vport_num)
+mlx5dr_fw_create_recalc_cs_ft(struct mlx5dr_domain *dmn, u16 vport_num)
 {
 	struct mlx5dr_cmd_create_flow_table_attr ft_attr = {};
 	struct mlx5dr_fw_recalc_cs_ft *recalc_cs_ft;
@@ -104,7 +104,8 @@
 			    bool reformat_req,
 			    u32 *tbl_id,
 			    u32 *group_id,
-			    bool ignore_flow_level)
+			    bool ignore_flow_level,
+			    u32 flow_source)
 {
 	struct mlx5dr_cmd_create_flow_table_attr ft_attr = {};
 	struct mlx5dr_cmd_fte_info fte_info = {};
@@ -139,6 +140,7 @@
 	fte_info.val = val;
 	fte_info.dest_arr = dest;
 	fte_info.ignore_flow_level = ignore_flow_level;
+	fte_info.flow_context.flow_source = flow_source;
 
 	ret = mlx5dr_cmd_set_fte(dmn->mdev, 0, 0, &ft_info, *group_id, &fte_info);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_icm_pool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_icm_pool.c
@@ -4,7 +4,6 @@
 #include "dr_types.h"
 
 #define DR_ICM_MODIFY_HDR_ALIGN_BASE 64
-#define DR_ICM_SYNC_THRESHOLD_POOL (64 * 1024 * 1024)
 
 struct mlx5dr_icm_pool {
 	enum mlx5dr_icm_type icm_type;
@@ -136,37 +135,35 @@
 	kvfree(icm_mr);
 }
 
-static int dr_icm_chunk_ste_init(struct mlx5dr_icm_chunk *chunk)
+static int dr_icm_buddy_get_ste_size(struct mlx5dr_icm_buddy_mem *buddy)
 {
-	chunk->ste_arr = kvzalloc(chunk->num_of_entries *
-				  sizeof(chunk->ste_arr[0]), GFP_KERNEL);
-	if (!chunk->ste_arr)
-		return -ENOMEM;
-
-	chunk->hw_ste_arr = kvzalloc(chunk->num_of_entries *
-				     DR_STE_SIZE_REDUCED, GFP_KERNEL);
-	if (!chunk->hw_ste_arr)
-		goto out_free_ste_arr;
-
-	chunk->miss_list = kvmalloc(chunk->num_of_entries *
-				    sizeof(chunk->miss_list[0]), GFP_KERNEL);
-	if (!chunk->miss_list)
-		goto out_free_hw_ste_arr;
+	/* We support only one type of STE size, both for ConnectX-5 and later
+	 * devices. Once the support for match STE which has a larger tag is
+	 * added (32B instead of 16B), the STE size for devices later than
+	 * ConnectX-5 needs to account for that.
+	 */
+	return DR_STE_SIZE_REDUCED;
+}
 
-	return 0;
+static void dr_icm_chunk_ste_init(struct mlx5dr_icm_chunk *chunk, int offset)
+{
+	struct mlx5dr_icm_buddy_mem *buddy = chunk->buddy_mem;
+	int index = offset / DR_STE_SIZE;
 
-out_free_hw_ste_arr:
-	kvfree(chunk->hw_ste_arr);
-out_free_ste_arr:
-	kvfree(chunk->ste_arr);
-	return -ENOMEM;
+	chunk->ste_arr = &buddy->ste_arr[index];
+	chunk->miss_list = &buddy->miss_list[index];
+	chunk->hw_ste_arr = buddy->hw_ste_arr +
+			    index * dr_icm_buddy_get_ste_size(buddy);
 }
 
 static void dr_icm_chunk_ste_cleanup(struct mlx5dr_icm_chunk *chunk)
 {
-	kvfree(chunk->miss_list);
-	kvfree(chunk->hw_ste_arr);
-	kvfree(chunk->ste_arr);
+	struct mlx5dr_icm_buddy_mem *buddy = chunk->buddy_mem;
+
+	memset(chunk->hw_ste_arr, 0,
+	       chunk->num_of_entries * dr_icm_buddy_get_ste_size(buddy));
+	memset(chunk->ste_arr, 0,
+	       chunk->num_of_entries * sizeof(chunk->ste_arr[0]));
 }
 
 static enum mlx5dr_icm_type
@@ -189,6 +186,44 @@
 	kvfree(chunk);
 }
 
+static int dr_icm_buddy_init_ste_cache(struct mlx5dr_icm_buddy_mem *buddy)
+{
+	int num_of_entries =
+		mlx5dr_icm_pool_chunk_size_to_entries(buddy->pool->max_log_chunk_sz);
+
+	buddy->ste_arr = kvcalloc(num_of_entries,
+				  sizeof(struct mlx5dr_ste), GFP_KERNEL);
+	if (!buddy->ste_arr)
+		return -ENOMEM;
+
+	/* Preallocate full STE size on non-ConnectX-5 devices since
+	 * we need to support both full and reduced with the same cache.
+	 */
+	buddy->hw_ste_arr = kvcalloc(num_of_entries,
+				     dr_icm_buddy_get_ste_size(buddy), GFP_KERNEL);
+	if (!buddy->hw_ste_arr)
+		goto free_ste_arr;
+
+	buddy->miss_list = kvmalloc(num_of_entries * sizeof(struct list_head), GFP_KERNEL);
+	if (!buddy->miss_list)
+		goto free_hw_ste_arr;
+
+	return 0;
+
+free_hw_ste_arr:
+	kvfree(buddy->hw_ste_arr);
+free_ste_arr:
+	kvfree(buddy->ste_arr);
+	return -ENOMEM;
+}
+
+static void dr_icm_buddy_cleanup_ste_cache(struct mlx5dr_icm_buddy_mem *buddy)
+{
+	kvfree(buddy->ste_arr);
+	kvfree(buddy->hw_ste_arr);
+	kvfree(buddy->miss_list);
+}
+
 static int dr_icm_buddy_create(struct mlx5dr_icm_pool *pool)
 {
 	struct mlx5dr_icm_buddy_mem *buddy;
@@ -208,11 +243,19 @@
 	buddy->icm_mr = icm_mr;
 	buddy->pool = pool;
 
+	if (pool->icm_type == DR_ICM_TYPE_STE) {
+		/* Reduce allocations by preallocating and reusing the STE structures */
+		if (dr_icm_buddy_init_ste_cache(buddy))
+			goto err_cleanup_buddy;
+	}
+
 	/* add it to the -start- of the list in order to search in it first */
 	list_add(&buddy->list_node, &pool->buddy_mem_list);
 
 	return 0;
 
+err_cleanup_buddy:
+	mlx5dr_buddy_cleanup(buddy);
 err_free_buddy:
 	kvfree(buddy);
 free_mr:
@@ -234,6 +277,9 @@
 
 	mlx5dr_buddy_cleanup(buddy);
 
+	if (buddy->pool->icm_type == DR_ICM_TYPE_STE)
+		dr_icm_buddy_cleanup_ste_cache(buddy);
+
 	kvfree(buddy);
 }
 
@@ -261,34 +307,30 @@
 	chunk->byte_size =
 		mlx5dr_icm_pool_chunk_size_to_byte(chunk_size, pool->icm_type);
 	chunk->seg = seg;
+	chunk->buddy_mem = buddy_mem_pool;
 
-	if (pool->icm_type == DR_ICM_TYPE_STE && dr_icm_chunk_ste_init(chunk)) {
-		mlx5dr_err(pool->dmn,
-			   "Failed to init ste arrays (order: %d)\n",
-			   chunk_size);
-		goto out_free_chunk;
-	}
+	if (pool->icm_type == DR_ICM_TYPE_STE)
+		dr_icm_chunk_ste_init(chunk, offset);
 
 	buddy_mem_pool->used_memory += chunk->byte_size;
-	chunk->buddy_mem = buddy_mem_pool;
 	INIT_LIST_HEAD(&chunk->chunk_list);
 
 	/* chunk now is part of the used_list */
 	list_add_tail(&chunk->chunk_list, &buddy_mem_pool->used_list);
 
 	return chunk;
-
-out_free_chunk:
-	kvfree(chunk);
-	return NULL;
 }
 
 static bool dr_icm_pool_is_sync_required(struct mlx5dr_icm_pool *pool)
 {
-	if (pool->hot_memory_size > DR_ICM_SYNC_THRESHOLD_POOL)
-		return true;
+	int allow_hot_size;
+
+	/* sync when hot memory reaches half of the pool size */
+	allow_hot_size =
+		mlx5dr_icm_pool_chunk_size_to_byte(pool->max_log_chunk_sz,
+						   pool->icm_type) / 2;
 
-	return false;
+	return pool->hot_memory_size > allow_hot_size;
 }
 
 static int dr_icm_pool_sync_all_buddy_pools(struct mlx5dr_icm_pool *pool)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_matcher.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_matcher.c
@@ -13,18 +13,6 @@
 	return (spec->dmac_47_16 || spec->dmac_15_0);
 }
 
-static bool dr_mask_is_src_addr_set(struct mlx5dr_match_spec *spec)
-{
-	return (spec->src_ip_127_96 || spec->src_ip_95_64 ||
-		spec->src_ip_63_32 || spec->src_ip_31_0);
-}
-
-static bool dr_mask_is_dst_addr_set(struct mlx5dr_match_spec *spec)
-{
-	return (spec->dst_ip_127_96 || spec->dst_ip_95_64 ||
-		spec->dst_ip_63_32 || spec->dst_ip_31_0);
-}
-
 static bool dr_mask_is_l3_base_set(struct mlx5dr_match_spec *spec)
 {
 	return (spec->ip_protocol || spec->frag || spec->tcp_flags ||
@@ -59,6 +47,11 @@
 	return spec->ttl_hoplimit;
 }
 
+static bool dr_mask_is_ipv4_ihl_set(struct mlx5dr_match_spec *spec)
+{
+	return spec->ipv4_ihl;
+}
+
 #define DR_MASK_IS_L2_DST(_spec, _misc, _inner_outer) (_spec.first_vid || \
 	(_spec).first_cfi || (_spec).first_prio || (_spec).cvlan_tag || \
 	(_spec).svlan_tag || (_spec).dmac_47_16 || (_spec).dmac_15_0 || \
@@ -115,7 +108,7 @@
 static bool
 dr_matcher_supp_vxlan_gpe(struct mlx5dr_cmd_caps *caps)
 {
-	return (caps->sw_format_ver == MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
+	return (caps->sw_format_ver >= MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
 	       (caps->flex_protocols & MLX5_FLEX_PARSER_VXLAN_GPE_ENABLED);
 }
 
@@ -141,9 +134,22 @@
 }
 
 static bool
+dr_matcher_supp_flex_parser_ok(struct mlx5dr_cmd_caps *caps)
+{
+	return caps->flex_parser_ok_bits_supp;
+}
+
+static bool dr_mask_is_tnl_geneve_tlv_opt_exist_set(struct mlx5dr_match_misc *misc,
+						    struct mlx5dr_domain *dmn)
+{
+	return dr_matcher_supp_flex_parser_ok(&dmn->info.caps) &&
+	       misc->geneve_tlv_option_0_exist;
+}
+
+static bool
 dr_matcher_supp_tnl_geneve(struct mlx5dr_cmd_caps *caps)
 {
-	return (caps->sw_format_ver == MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
+	return (caps->sw_format_ver >= MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
 	       (caps->flex_protocols & MLX5_FLEX_PARSER_GENEVE_ENABLED);
 }
 
@@ -260,13 +266,13 @@
 
 static int dr_matcher_supp_icmp_v4(struct mlx5dr_cmd_caps *caps)
 {
-	return (caps->sw_format_ver == MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
+	return (caps->sw_format_ver >= MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
 	       (caps->flex_protocols & MLX5_FLEX_PARSER_ICMP_V4_ENABLED);
 }
 
 static int dr_matcher_supp_icmp_v6(struct mlx5dr_cmd_caps *caps)
 {
-	return (caps->sw_format_ver == MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
+	return (caps->sw_format_ver >= MLX5_STEERING_FORMAT_CONNECTX_6DX) ||
 	       (caps->flex_protocols & MLX5_FLEX_PARSER_ICMP_V6_ENABLED);
 }
 
@@ -359,7 +365,7 @@
 
 static int dr_matcher_supp_tnl_mpls_over_udp(struct mlx5dr_cmd_caps *caps)
 {
-	return caps->flex_protocols & mlx5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED;
+	return caps->flex_protocols & MLX5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED;
 }
 
 static bool dr_mask_is_tnl_mpls_over_udp(struct mlx5dr_match_param *mask,
@@ -368,6 +374,12 @@
 	return DR_MASK_IS_OUTER_MPLS_OVER_UDP_SET(&mask->misc2) &&
 	       dr_matcher_supp_tnl_mpls_over_udp(&dmn->info.caps);
 }
+
+static bool dr_mask_is_tnl_header_0_1_set(struct mlx5dr_match_misc5 *misc5)
+{
+	return misc5->tunnel_header_0 || misc5->tunnel_header_1;
+}
+
 int mlx5dr_matcher_select_builders(struct mlx5dr_matcher *matcher,
 				   struct mlx5dr_matcher_rx_tx *nic_matcher,
 				   enum mlx5dr_ipv outer_ipv,
@@ -424,6 +436,9 @@
 	if (matcher->match_criteria & DR_MATCHER_CRITERIA_MISC4)
 		mask.misc4 = matcher->mask.misc4;
 
+	if (matcher->match_criteria & DR_MATCHER_CRITERIA_MISC5)
+		mask.misc5 = matcher->mask.misc5;
+
 	ret = mlx5dr_ste_build_pre_check(dmn, matcher->match_criteria,
 					 &matcher->mask, NULL);
 	if (ret)
@@ -443,7 +458,8 @@
 	if (matcher->match_criteria & (DR_MATCHER_CRITERIA_OUTER |
 				       DR_MATCHER_CRITERIA_MISC |
 				       DR_MATCHER_CRITERIA_MISC2 |
-				       DR_MATCHER_CRITERIA_MISC3)) {
+				       DR_MATCHER_CRITERIA_MISC3 |
+				       DR_MATCHER_CRITERIA_MISC5)) {
 		inner = false;
 
 		if (dr_mask_is_wqe_metadata_set(&mask.misc2))
@@ -480,11 +496,11 @@
 						    &mask, inner, rx);
 
 		if (outer_ipv == DR_RULE_IPV6) {
-			if (dr_mask_is_dst_addr_set(&mask.outer))
+			if (DR_MASK_IS_DST_IP_SET(&mask.outer))
 				mlx5dr_ste_build_eth_l3_ipv6_dst(ste_ctx, &sb[idx++],
 								 &mask, inner, rx);
 
-			if (dr_mask_is_src_addr_set(&mask.outer))
+			if (DR_MASK_IS_SRC_IP_SET(&mask.outer))
 				mlx5dr_ste_build_eth_l3_ipv6_src(ste_ctx, &sb[idx++],
 								 &mask, inner, rx);
 
@@ -496,7 +512,8 @@
 				mlx5dr_ste_build_eth_l3_ipv4_5_tuple(ste_ctx, &sb[idx++],
 								     &mask, inner, rx);
 
-			if (dr_mask_is_ttl_set(&mask.outer))
+			if (dr_mask_is_ttl_set(&mask.outer) ||
+			    dr_mask_is_ipv4_ihl_set(&mask.outer))
 				mlx5dr_ste_build_eth_l3_ipv4_misc(ste_ctx, &sb[idx++],
 								  &mask, inner, rx);
 		}
@@ -511,6 +528,10 @@
 				mlx5dr_ste_build_tnl_geneve_tlv_opt(ste_ctx, &sb[idx++],
 								    &mask, &dmn->info.caps,
 								    inner, rx);
+			if (dr_mask_is_tnl_geneve_tlv_opt_exist_set(&mask.misc, dmn))
+				mlx5dr_ste_build_tnl_geneve_tlv_opt_exist(ste_ctx, &sb[idx++],
+									  &mask, &dmn->info.caps,
+									  inner, rx);
 		} else if (dr_mask_is_tnl_gtpu_any(&mask, dmn)) {
 			if (dr_mask_is_tnl_gtpu_flex_parser_0(&mask, dmn))
 				mlx5dr_ste_build_tnl_gtpu_flex_parser_0(ste_ctx, &sb[idx++],
@@ -525,6 +546,9 @@
 			if (dr_mask_is_tnl_gtpu(&mask, dmn))
 				mlx5dr_ste_build_tnl_gtpu(ste_ctx, &sb[idx++],
 							  &mask, inner, rx);
+		} else if (dr_mask_is_tnl_header_0_1_set(&mask.misc5)) {
+			mlx5dr_ste_build_tnl_header_0_1(ste_ctx, &sb[idx++],
+							&mask, inner, rx);
 		}
 
 		if (DR_MASK_IS_ETH_L4_MISC_SET(mask.misc3, outer))
@@ -580,11 +604,11 @@
 						    &mask, inner, rx);
 
 		if (inner_ipv == DR_RULE_IPV6) {
-			if (dr_mask_is_dst_addr_set(&mask.inner))
+			if (DR_MASK_IS_DST_IP_SET(&mask.inner))
 				mlx5dr_ste_build_eth_l3_ipv6_dst(ste_ctx, &sb[idx++],
 								 &mask, inner, rx);
 
-			if (dr_mask_is_src_addr_set(&mask.inner))
+			if (DR_MASK_IS_SRC_IP_SET(&mask.inner))
 				mlx5dr_ste_build_eth_l3_ipv6_src(ste_ctx, &sb[idx++],
 								 &mask, inner, rx);
 
@@ -596,7 +620,8 @@
 				mlx5dr_ste_build_eth_l3_ipv4_5_tuple(ste_ctx, &sb[idx++],
 								     &mask, inner, rx);
 
-			if (dr_mask_is_ttl_set(&mask.inner))
+			if (dr_mask_is_ttl_set(&mask.inner) ||
+			    dr_mask_is_ipv4_ihl_set(&mask.inner))
 				mlx5dr_ste_build_eth_l3_ipv4_misc(ste_ctx, &sb[idx++],
 								  &mask, inner, rx);
 		}
@@ -653,10 +678,10 @@
 	return 0;
 }
 
-static int dr_matcher_connect(struct mlx5dr_domain *dmn,
-			      struct mlx5dr_matcher_rx_tx *curr_nic_matcher,
-			      struct mlx5dr_matcher_rx_tx *next_nic_matcher,
-			      struct mlx5dr_matcher_rx_tx *prev_nic_matcher)
+static int dr_nic_matcher_connect(struct mlx5dr_domain *dmn,
+				  struct mlx5dr_matcher_rx_tx *curr_nic_matcher,
+				  struct mlx5dr_matcher_rx_tx *next_nic_matcher,
+				  struct mlx5dr_matcher_rx_tx *prev_nic_matcher)
 {
 	struct mlx5dr_table_rx_tx *nic_tbl = curr_nic_matcher->nic_tbl;
 	struct mlx5dr_domain_rx_tx *nic_dmn = nic_tbl->nic_dmn;
@@ -712,58 +737,50 @@
 	return 0;
 }
 
-static int dr_matcher_add_to_tbl(struct mlx5dr_matcher *matcher)
+int mlx5dr_matcher_add_to_tbl_nic(struct mlx5dr_domain *dmn,
+				  struct mlx5dr_matcher_rx_tx *nic_matcher)
 {
-	struct mlx5dr_matcher *next_matcher, *prev_matcher, *tmp_matcher;
-	struct mlx5dr_table *tbl = matcher->tbl;
-	struct mlx5dr_domain *dmn = tbl->dmn;
+	struct mlx5dr_matcher_rx_tx *next_nic_matcher, *prev_nic_matcher, *tmp_nic_matcher;
+	struct mlx5dr_table_rx_tx *nic_tbl = nic_matcher->nic_tbl;
 	bool first = true;
 	int ret;
 
-	next_matcher = NULL;
-	list_for_each_entry(tmp_matcher, &tbl->matcher_list, matcher_list) {
-		if (tmp_matcher->prio >= matcher->prio) {
-			next_matcher = tmp_matcher;
+	/* If the nic matcher is already on its parent nic table list,
+	 * then it is already connected to the chain of nic matchers.
+	 */
+	if (!list_empty(&nic_matcher->list_node))
+		return 0;
+
+	next_nic_matcher = NULL;
+	list_for_each_entry(tmp_nic_matcher, &nic_tbl->nic_matcher_list, list_node) {
+		if (tmp_nic_matcher->prio >= nic_matcher->prio) {
+			next_nic_matcher = tmp_nic_matcher;
 			break;
 		}
 		first = false;
 	}
 
-	prev_matcher = NULL;
-	if (next_matcher && !first)
-		prev_matcher = list_prev_entry(next_matcher, matcher_list);
+	prev_nic_matcher = NULL;
+	if (next_nic_matcher && !first)
+		prev_nic_matcher = list_prev_entry(next_nic_matcher, list_node);
 	else if (!first)
-		prev_matcher = list_last_entry(&tbl->matcher_list,
-					       struct mlx5dr_matcher,
-					       matcher_list);
-
-	if (dmn->type == MLX5DR_DOMAIN_TYPE_FDB ||
-	    dmn->type == MLX5DR_DOMAIN_TYPE_NIC_RX) {
-		ret = dr_matcher_connect(dmn, &matcher->rx,
-					 next_matcher ? &next_matcher->rx : NULL,
-					 prev_matcher ?	&prev_matcher->rx : NULL);
-		if (ret)
-			return ret;
-	}
+		prev_nic_matcher = list_last_entry(&nic_tbl->nic_matcher_list,
+						   struct mlx5dr_matcher_rx_tx,
+						   list_node);
 
-	if (dmn->type == MLX5DR_DOMAIN_TYPE_FDB ||
-	    dmn->type == MLX5DR_DOMAIN_TYPE_NIC_TX) {
-		ret = dr_matcher_connect(dmn, &matcher->tx,
-					 next_matcher ? &next_matcher->tx : NULL,
-					 prev_matcher ?	&prev_matcher->tx : NULL);
-		if (ret)
-			return ret;
-	}
+	ret = dr_nic_matcher_connect(dmn, nic_matcher,
+				     next_nic_matcher, prev_nic_matcher);
+	if (ret)
+		return ret;
 
-	if (prev_matcher)
-		list_add(&matcher->matcher_list, &prev_matcher->matcher_list);
-	else if (next_matcher)
-		list_add_tail(&matcher->matcher_list,
-			      &next_matcher->matcher_list);
+	if (prev_nic_matcher)
+		list_add(&nic_matcher->list_node, &prev_nic_matcher->list_node);
+	else if (next_nic_matcher)
+		list_add_tail(&nic_matcher->list_node, &next_nic_matcher->list_node);
 	else
-		list_add(&matcher->matcher_list, &tbl->matcher_list);
+		list_add(&nic_matcher->list_node, &nic_matcher->nic_tbl->nic_matcher_list);
 
-	return 0;
+	return ret;
 }
 
 static void dr_matcher_uninit_nic(struct mlx5dr_matcher_rx_tx *nic_matcher)
@@ -822,6 +839,9 @@
 	struct mlx5dr_domain *dmn = matcher->tbl->dmn;
 	int ret;
 
+	nic_matcher->prio = matcher->prio;
+	INIT_LIST_HEAD(&nic_matcher->list_node);
+
 	ret = dr_matcher_set_all_ste_builders(matcher, nic_matcher);
 	if (ret)
 		return ret;
@@ -872,12 +892,12 @@
 	return ret;
 }
 
-static int dr_matcher_init(struct mlx5dr_matcher *matcher,
-			   struct mlx5dr_match_parameters *mask)
+static int dr_matcher_copy_param(struct mlx5dr_matcher *matcher,
+				 struct mlx5dr_match_parameters *mask)
 {
-	struct mlx5dr_table *tbl = matcher->tbl;
-	struct mlx5dr_domain *dmn = tbl->dmn;
-	int ret;
+	struct mlx5dr_domain *dmn = matcher->tbl->dmn;
+	struct mlx5dr_match_parameters consumed_mask;
+	int i, ret = 0;
 
 	if (matcher->match_criteria >= DR_MATCHER_CRITERIA_MAX) {
 		mlx5dr_err(dmn, "Invalid match criteria attribute\n");
@@ -889,10 +909,44 @@
 			mlx5dr_err(dmn, "Invalid match size attribute\n");
 			return -EINVAL;
 		}
+
+		consumed_mask.match_buf = kzalloc(mask->match_sz, GFP_KERNEL);
+		if (!consumed_mask.match_buf)
+			return -ENOMEM;
+
+		consumed_mask.match_sz = mask->match_sz;
+		memcpy(consumed_mask.match_buf, mask->match_buf, mask->match_sz);
 		mlx5dr_ste_copy_param(matcher->match_criteria,
-				      &matcher->mask, mask);
+				      &matcher->mask, &consumed_mask, true);
+
+		/* Check that all mask data was consumed */
+		for (i = 0; i < consumed_mask.match_sz; i++) {
+			if (!((u8 *)consumed_mask.match_buf)[i])
+				continue;
+
+			mlx5dr_dbg(dmn,
+				   "Match param mask contains unsupported parameters\n");
+			ret = -EOPNOTSUPP;
+			break;
+		}
+
+		kfree(consumed_mask.match_buf);
 	}
 
+	return ret;
+}
+
+static int dr_matcher_init(struct mlx5dr_matcher *matcher,
+			   struct mlx5dr_match_parameters *mask)
+{
+	struct mlx5dr_table *tbl = matcher->tbl;
+	struct mlx5dr_domain *dmn = tbl->dmn;
+	int ret;
+
+	ret = dr_matcher_copy_param(matcher, mask);
+	if (ret)
+		return ret;
+
 	switch (dmn->type) {
 	case MLX5DR_DOMAIN_TYPE_NIC_RX:
 		matcher->rx.nic_tbl = &tbl->rx;
@@ -909,12 +963,26 @@
 		break;
 	default:
 		WARN_ON(true);
-		return -EINVAL;
+		ret = -EINVAL;
 	}
 
 	return ret;
 }
 
+static void dr_matcher_add_to_dbg_list(struct mlx5dr_matcher *matcher)
+{
+	mutex_lock(&matcher->tbl->dmn->dump_info.dbg_mutex);
+	list_add(&matcher->list_node, &matcher->tbl->matcher_list);
+	mutex_unlock(&matcher->tbl->dmn->dump_info.dbg_mutex);
+}
+
+static void dr_matcher_remove_from_dbg_list(struct mlx5dr_matcher *matcher)
+{
+	mutex_lock(&matcher->tbl->dmn->dump_info.dbg_mutex);
+	list_del(&matcher->list_node);
+	mutex_unlock(&matcher->tbl->dmn->dump_info.dbg_mutex);
+}
+
 struct mlx5dr_matcher *
 mlx5dr_matcher_create(struct mlx5dr_table *tbl,
 		      u32 priority,
@@ -934,7 +1002,8 @@
 	matcher->prio = priority;
 	matcher->match_criteria = match_criteria_enable;
 	refcount_set(&matcher->refcount, 1);
-	INIT_LIST_HEAD(&matcher->matcher_list);
+	INIT_LIST_HEAD(&matcher->list_node);
+	INIT_LIST_HEAD(&matcher->dbg_rule_list);
 
 	mlx5dr_domain_lock(tbl->dmn);
 
@@ -942,16 +1011,12 @@
 	if (ret)
 		goto free_matcher;
 
-	ret = dr_matcher_add_to_tbl(matcher);
-	if (ret)
-		goto matcher_uninit;
+	dr_matcher_add_to_dbg_list(matcher);
 
 	mlx5dr_domain_unlock(tbl->dmn);
 
 	return matcher;
 
-matcher_uninit:
-	dr_matcher_uninit(matcher);
 free_matcher:
 	mlx5dr_domain_unlock(tbl->dmn);
 	kfree(matcher);
@@ -960,10 +1025,10 @@
 	return NULL;
 }
 
-static int dr_matcher_disconnect(struct mlx5dr_domain *dmn,
-				 struct mlx5dr_table_rx_tx *nic_tbl,
-				 struct mlx5dr_matcher_rx_tx *next_nic_matcher,
-				 struct mlx5dr_matcher_rx_tx *prev_nic_matcher)
+static int dr_matcher_disconnect_nic(struct mlx5dr_domain *dmn,
+				     struct mlx5dr_table_rx_tx *nic_tbl,
+				     struct mlx5dr_matcher_rx_tx *next_nic_matcher,
+				     struct mlx5dr_matcher_rx_tx *prev_nic_matcher)
 {
 	struct mlx5dr_domain_rx_tx *nic_dmn = nic_tbl->nic_dmn;
 	struct mlx5dr_htbl_connect_info info;
@@ -990,43 +1055,34 @@
 						 &info, true);
 }
 
-static int dr_matcher_remove_from_tbl(struct mlx5dr_matcher *matcher)
+int mlx5dr_matcher_remove_from_tbl_nic(struct mlx5dr_domain *dmn,
+				       struct mlx5dr_matcher_rx_tx *nic_matcher)
 {
-	struct mlx5dr_matcher *prev_matcher, *next_matcher;
-	struct mlx5dr_table *tbl = matcher->tbl;
-	struct mlx5dr_domain *dmn = tbl->dmn;
-	int ret = 0;
+	struct mlx5dr_matcher_rx_tx *prev_nic_matcher, *next_nic_matcher;
+	struct mlx5dr_table_rx_tx *nic_tbl = nic_matcher->nic_tbl;
+	int ret;
 
-	if (list_is_last(&matcher->matcher_list, &tbl->matcher_list))
-		next_matcher = NULL;
-	else
-		next_matcher = list_next_entry(matcher, matcher_list);
+	/* If the nic matcher is not on its parent nic table list,
+	 * then it is detached - no need to disconnect it.
+	 */
+	if (list_empty(&nic_matcher->list_node))
+		return 0;
 
-	if (matcher->matcher_list.prev == &tbl->matcher_list)
-		prev_matcher = NULL;
+	if (list_is_last(&nic_matcher->list_node, &nic_tbl->nic_matcher_list))
+		next_nic_matcher = NULL;
 	else
-		prev_matcher = list_prev_entry(matcher, matcher_list);
-
-	if (dmn->type == MLX5DR_DOMAIN_TYPE_FDB ||
-	    dmn->type == MLX5DR_DOMAIN_TYPE_NIC_RX) {
-		ret = dr_matcher_disconnect(dmn, &tbl->rx,
-					    next_matcher ? &next_matcher->rx : NULL,
-					    prev_matcher ? &prev_matcher->rx : NULL);
-		if (ret)
-			return ret;
-	}
+		next_nic_matcher = list_next_entry(nic_matcher, list_node);
 
-	if (dmn->type == MLX5DR_DOMAIN_TYPE_FDB ||
-	    dmn->type == MLX5DR_DOMAIN_TYPE_NIC_TX) {
-		ret = dr_matcher_disconnect(dmn, &tbl->tx,
-					    next_matcher ? &next_matcher->tx : NULL,
-					    prev_matcher ? &prev_matcher->tx : NULL);
-		if (ret)
-			return ret;
-	}
+	if (nic_matcher->list_node.prev == &nic_tbl->nic_matcher_list)
+		prev_nic_matcher = NULL;
+	else
+		prev_nic_matcher = list_prev_entry(nic_matcher, list_node);
 
-	list_del(&matcher->matcher_list);
+	ret = dr_matcher_disconnect_nic(dmn, nic_tbl, next_nic_matcher, prev_nic_matcher);
+	if (ret)
+		return ret;
 
+	list_del_init(&nic_matcher->list_node);
 	return 0;
 }
 
@@ -1034,12 +1090,12 @@
 {
 	struct mlx5dr_table *tbl = matcher->tbl;
 
-	if (refcount_read(&matcher->refcount) > 1)
+	if (WARN_ON_ONCE(refcount_read(&matcher->refcount) > 1))
 		return -EBUSY;
 
 	mlx5dr_domain_lock(tbl->dmn);
 
-	dr_matcher_remove_from_tbl(matcher);
+	dr_matcher_remove_from_dbg_list(matcher);
 	dr_matcher_uninit(matcher);
 	refcount_dec(&matcher->tbl->refcount);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_rule.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_rule.c
@@ -5,11 +5,6 @@
 
 #define DR_RULE_MAX_STE_CHAIN (DR_RULE_MAX_STES + DR_ACTION_MAX_STES)
 
-struct mlx5dr_rule_action_member {
-	struct mlx5dr_action *action;
-	struct list_head list;
-};
-
 static int dr_rule_append_to_miss_list(struct mlx5dr_ste_ctx *ste_ctx,
 				       struct mlx5dr_ste *new_last_ste,
 				       struct list_head *miss_list,
@@ -917,7 +912,7 @@
 		return false;
 	}
 
-	mlx5dr_ste_copy_param(matcher->match_criteria, param, value);
+	mlx5dr_ste_copy_param(matcher->match_criteria, param, value, false);
 
 	if (match_criteria & DR_MATCHER_CRITERIA_OUTER) {
 		s_idx = offsetof(struct mlx5dr_match_param, outer);
@@ -979,14 +974,36 @@
 			return false;
 		}
 	}
+
+	if (match_criteria & DR_MATCHER_CRITERIA_MISC5) {
+		s_idx = offsetof(struct mlx5dr_match_param, misc5);
+		e_idx = min(s_idx + sizeof(param->misc5), value_size);
+
+		if (!dr_rule_cmp_value_to_mask(mask_p, param_p, s_idx, e_idx)) {
+			mlx5dr_err(matcher->tbl->dmn, "Rule misc5 parameters contains a value not specified by mask\n");
+			return false;
+		}
+	}
 	return true;
 }
 
 static int dr_rule_destroy_rule_nic(struct mlx5dr_rule *rule,
 				    struct mlx5dr_rule_rx_tx *nic_rule)
 {
+	/* Check if this nic rule was actually created, or was it skipped
+	 * and only the other type of the RX/TX nic rule was created.
+	 */
+	if (!nic_rule->last_rule_ste)
+		return 0;
+
 	mlx5dr_domain_nic_lock(nic_rule->nic_matcher->nic_tbl->nic_dmn);
 	dr_rule_clean_rule_members(rule, nic_rule);
+
+	nic_rule->nic_matcher->rules--;
+	if (!nic_rule->nic_matcher->rules)
+		mlx5dr_matcher_remove_from_tbl_nic(rule->matcher->tbl->dmn,
+						   nic_rule->nic_matcher);
+
 	mlx5dr_domain_nic_unlock(nic_rule->nic_matcher->nic_tbl->nic_dmn);
 
 	return 0;
@@ -1003,6 +1020,8 @@
 {
 	struct mlx5dr_domain *dmn = rule->matcher->tbl->dmn;
 
+	mlx5dr_dbg_rule_del(rule);
+
 	switch (dmn->type) {
 	case MLX5DR_DOMAIN_TYPE_NIC_RX:
 		dr_rule_destroy_rule_nic(rule, &rule->rx);
@@ -1042,10 +1061,10 @@
 		return false;
 
 	if (mask->misc.source_port) {
-		if (rx && value->misc.source_port != WIRE_PORT)
+		if (rx && value->misc.source_port != MLX5_VPORT_UPLINK)
 			return true;
 
-		if (!rx && value->misc.source_port == WIRE_PORT)
+		if (!rx && value->misc.source_port == MLX5_VPORT_UPLINK)
 			return true;
 	}
 
@@ -1091,24 +1110,28 @@
 
 	mlx5dr_domain_nic_lock(nic_dmn);
 
+	ret = mlx5dr_matcher_add_to_tbl_nic(dmn, nic_matcher);
+	if (ret)
+		goto free_hw_ste;
+
 	ret = mlx5dr_matcher_select_builders(matcher,
 					     nic_matcher,
 					     dr_rule_get_ipv(&param->outer),
 					     dr_rule_get_ipv(&param->inner));
 	if (ret)
-		goto free_hw_ste;
+		goto remove_from_nic_tbl;
 
 	/* Set the tag values inside the ste array */
 	ret = mlx5dr_ste_build_ste_arr(matcher, nic_matcher, param, hw_ste_arr);
 	if (ret)
-		goto free_hw_ste;
+		goto remove_from_nic_tbl;
 
 	/* Set the actions values/addresses inside the ste array */
 	ret = mlx5dr_actions_build_ste_arr(matcher, nic_matcher, actions,
 					   num_actions, hw_ste_arr,
 					   &new_hw_ste_arr_sz);
 	if (ret)
-		goto free_hw_ste;
+		goto remove_from_nic_tbl;
 
 	cur_htbl = nic_matcher->s_htbl;
 
@@ -1155,6 +1178,8 @@
 	if (htbl)
 		mlx5dr_htbl_put(htbl);
 
+	nic_matcher->rules++;
+
 	mlx5dr_domain_nic_unlock(nic_dmn);
 
 	kfree(hw_ste_arr);
@@ -1168,6 +1193,10 @@
 		list_del(&ste_info->send_list);
 		kfree(ste_info);
 	}
+
+remove_from_nic_tbl:
+	mlx5dr_matcher_remove_from_tbl_nic(dmn, nic_matcher);
+
 free_hw_ste:
 	mlx5dr_domain_nic_unlock(nic_dmn);
 	kfree(hw_ste_arr);
@@ -1257,6 +1286,8 @@
 	if (ret)
 		goto remove_action_members;
 
+	INIT_LIST_HEAD(&rule->dbg_node);
+	mlx5dr_dbg_rule_add(rule);
 	return rule;
 
 remove_action_members:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c
@@ -15,7 +15,8 @@
 {
 	u32 crc = crc32(0, input_data, length);
 
-	return (__force u32)htonl(crc);
+	return (__force u32)((crc >> 24) & 0xff) | ((crc << 8) & 0xff0000) |
+			    ((crc >> 8) & 0xff00) | ((crc << 24) & 0xff000000);
 }
 
 bool mlx5dr_ste_supp_ttl_cs_recalc(struct mlx5dr_cmd_caps *caps)
@@ -523,8 +524,8 @@
 			       struct mlx5dr_ste_actions_attr *attr,
 			       u32 *added_stes)
 {
-	ste_ctx->set_actions_tx(dmn, action_type_set, hw_ste_arr,
-				attr, added_stes);
+	ste_ctx->set_actions_tx(dmn, action_type_set, ste_ctx->actions_caps,
+				hw_ste_arr, attr, added_stes);
 }
 
 void mlx5dr_ste_set_actions_rx(struct mlx5dr_ste_ctx *ste_ctx,
@@ -534,8 +535,8 @@
 			       struct mlx5dr_ste_actions_attr *attr,
 			       u32 *added_stes)
 {
-	ste_ctx->set_actions_rx(dmn, action_type_set, hw_ste_arr,
-				attr, added_stes);
+	ste_ctx->set_actions_rx(dmn, action_type_set, ste_ctx->actions_caps,
+				hw_ste_arr, attr, added_stes);
 }
 
 const struct mlx5dr_ste_action_modify_field *
@@ -602,12 +603,34 @@
 						 used_hw_action_num);
 }
 
+static int dr_ste_build_pre_check_spec(struct mlx5dr_domain *dmn,
+				       struct mlx5dr_match_spec *spec)
+{
+	if (spec->ip_version) {
+		if (spec->ip_version != 0xf) {
+			mlx5dr_err(dmn,
+				   "Partial ip_version mask with src/dst IP is not supported\n");
+			return -EINVAL;
+		}
+	} else if (spec->ethertype != 0xffff &&
+		   (DR_MASK_IS_SRC_IP_SET(spec) || DR_MASK_IS_DST_IP_SET(spec))) {
+		mlx5dr_err(dmn,
+			   "Partial/no ethertype mask with src/dst IP is not supported\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 int mlx5dr_ste_build_pre_check(struct mlx5dr_domain *dmn,
 			       u8 match_criteria,
 			       struct mlx5dr_match_param *mask,
 			       struct mlx5dr_match_param *value)
 {
-	if (!value && (match_criteria & DR_MATCHER_CRITERIA_MISC)) {
+	if (value)
+		return 0;
+
+	if (match_criteria & DR_MATCHER_CRITERIA_MISC) {
 		if (mask->misc.source_port && mask->misc.source_port != 0xffff) {
 			mlx5dr_err(dmn,
 				   "Partial mask source_port is not supported\n");
@@ -621,6 +644,14 @@
 		}
 	}
 
+	if ((match_criteria & DR_MATCHER_CRITERIA_OUTER) &&
+	    dr_ste_build_pre_check_spec(dmn, &mask->outer))
+		return -EINVAL;
+
+	if ((match_criteria & DR_MATCHER_CRITERIA_INNER) &&
+	    dr_ste_build_pre_check_spec(dmn, &mask->inner))
+		return -EINVAL;
+
 	return 0;
 }
 
@@ -668,101 +699,119 @@
 	return 0;
 }
 
-static void dr_ste_copy_mask_misc(char *mask, struct mlx5dr_match_misc *spec)
-{
-	spec->gre_c_present = MLX5_GET(fte_match_set_misc, mask, gre_c_present);
-	spec->gre_k_present = MLX5_GET(fte_match_set_misc, mask, gre_k_present);
-	spec->gre_s_present = MLX5_GET(fte_match_set_misc, mask, gre_s_present);
-	spec->source_vhca_port = MLX5_GET(fte_match_set_misc, mask, source_vhca_port);
-	spec->source_sqn = MLX5_GET(fte_match_set_misc, mask, source_sqn);
-
-	spec->source_port = MLX5_GET(fte_match_set_misc, mask, source_port);
-	spec->source_eswitch_owner_vhca_id = MLX5_GET(fte_match_set_misc, mask,
-						      source_eswitch_owner_vhca_id);
-
-	spec->outer_second_prio = MLX5_GET(fte_match_set_misc, mask, outer_second_prio);
-	spec->outer_second_cfi = MLX5_GET(fte_match_set_misc, mask, outer_second_cfi);
-	spec->outer_second_vid = MLX5_GET(fte_match_set_misc, mask, outer_second_vid);
-	spec->inner_second_prio = MLX5_GET(fte_match_set_misc, mask, inner_second_prio);
-	spec->inner_second_cfi = MLX5_GET(fte_match_set_misc, mask, inner_second_cfi);
-	spec->inner_second_vid = MLX5_GET(fte_match_set_misc, mask, inner_second_vid);
+#define IFC_GET_CLR(typ, p, fld, clear) ({ \
+	void *__p = (p); \
+	u32 __t = MLX5_GET(typ, __p, fld); \
+	if (clear) \
+		MLX5_SET(typ, __p, fld, 0); \
+	__t; \
+})
+
+#define memcpy_and_clear(to, from, len, clear) ({ \
+	void *__to = (to), *__from = (from); \
+	size_t __len = (len); \
+	memcpy(__to, __from, __len); \
+	if (clear) \
+		memset(__from, 0, __len); \
+})
+
+static void dr_ste_copy_mask_misc(char *mask, struct mlx5dr_match_misc *spec, bool clr)
+{
+	spec->gre_c_present = IFC_GET_CLR(fte_match_set_misc, mask, gre_c_present, clr);
+	spec->gre_k_present = IFC_GET_CLR(fte_match_set_misc, mask, gre_k_present, clr);
+	spec->gre_s_present = IFC_GET_CLR(fte_match_set_misc, mask, gre_s_present, clr);
+	spec->source_vhca_port = IFC_GET_CLR(fte_match_set_misc, mask, source_vhca_port, clr);
+	spec->source_sqn = IFC_GET_CLR(fte_match_set_misc, mask, source_sqn, clr);
+
+	spec->source_port = IFC_GET_CLR(fte_match_set_misc, mask, source_port, clr);
+	spec->source_eswitch_owner_vhca_id =
+		IFC_GET_CLR(fte_match_set_misc, mask, source_eswitch_owner_vhca_id, clr);
+
+	spec->outer_second_prio = IFC_GET_CLR(fte_match_set_misc, mask, outer_second_prio, clr);
+	spec->outer_second_cfi = IFC_GET_CLR(fte_match_set_misc, mask, outer_second_cfi, clr);
+	spec->outer_second_vid = IFC_GET_CLR(fte_match_set_misc, mask, outer_second_vid, clr);
+	spec->inner_second_prio = IFC_GET_CLR(fte_match_set_misc, mask, inner_second_prio, clr);
+	spec->inner_second_cfi = IFC_GET_CLR(fte_match_set_misc, mask, inner_second_cfi, clr);
+	spec->inner_second_vid = IFC_GET_CLR(fte_match_set_misc, mask, inner_second_vid, clr);
 
 	spec->outer_second_cvlan_tag =
-		MLX5_GET(fte_match_set_misc, mask, outer_second_cvlan_tag);
+		IFC_GET_CLR(fte_match_set_misc, mask, outer_second_cvlan_tag, clr);
 	spec->inner_second_cvlan_tag =
-		MLX5_GET(fte_match_set_misc, mask, inner_second_cvlan_tag);
+		IFC_GET_CLR(fte_match_set_misc, mask, inner_second_cvlan_tag, clr);
 	spec->outer_second_svlan_tag =
-		MLX5_GET(fte_match_set_misc, mask, outer_second_svlan_tag);
+		IFC_GET_CLR(fte_match_set_misc, mask, outer_second_svlan_tag, clr);
 	spec->inner_second_svlan_tag =
-		MLX5_GET(fte_match_set_misc, mask, inner_second_svlan_tag);
-
-	spec->gre_protocol = MLX5_GET(fte_match_set_misc, mask, gre_protocol);
+		IFC_GET_CLR(fte_match_set_misc, mask, inner_second_svlan_tag, clr);
+	spec->gre_protocol = IFC_GET_CLR(fte_match_set_misc, mask, gre_protocol, clr);
 
-	spec->gre_key_h = MLX5_GET(fte_match_set_misc, mask, gre_key.nvgre.hi);
-	spec->gre_key_l = MLX5_GET(fte_match_set_misc, mask, gre_key.nvgre.lo);
+	spec->gre_key_h = IFC_GET_CLR(fte_match_set_misc, mask, gre_key.nvgre.hi, clr);
+	spec->gre_key_l = IFC_GET_CLR(fte_match_set_misc, mask, gre_key.nvgre.lo, clr);
 
-	spec->vxlan_vni = MLX5_GET(fte_match_set_misc, mask, vxlan_vni);
+	spec->vxlan_vni = IFC_GET_CLR(fte_match_set_misc, mask, vxlan_vni, clr);
 
-	spec->geneve_vni = MLX5_GET(fte_match_set_misc, mask, geneve_vni);
-	spec->geneve_oam = MLX5_GET(fte_match_set_misc, mask, geneve_oam);
+	spec->geneve_vni = IFC_GET_CLR(fte_match_set_misc, mask, geneve_vni, clr);
+	spec->geneve_tlv_option_0_exist =
+		IFC_GET_CLR(fte_match_set_misc, mask, geneve_tlv_option_0_exist, clr);
+	spec->geneve_oam = IFC_GET_CLR(fte_match_set_misc, mask, geneve_oam, clr);
 
 	spec->outer_ipv6_flow_label =
-		MLX5_GET(fte_match_set_misc, mask, outer_ipv6_flow_label);
+		IFC_GET_CLR(fte_match_set_misc, mask, outer_ipv6_flow_label, clr);
 
 	spec->inner_ipv6_flow_label =
-		MLX5_GET(fte_match_set_misc, mask, inner_ipv6_flow_label);
+		IFC_GET_CLR(fte_match_set_misc, mask, inner_ipv6_flow_label, clr);
 
-	spec->geneve_opt_len = MLX5_GET(fte_match_set_misc, mask, geneve_opt_len);
+	spec->geneve_opt_len = IFC_GET_CLR(fte_match_set_misc, mask, geneve_opt_len, clr);
 	spec->geneve_protocol_type =
-		MLX5_GET(fte_match_set_misc, mask, geneve_protocol_type);
+		IFC_GET_CLR(fte_match_set_misc, mask, geneve_protocol_type, clr);
 
-	spec->bth_dst_qp = MLX5_GET(fte_match_set_misc, mask, bth_dst_qp);
+	spec->bth_dst_qp = IFC_GET_CLR(fte_match_set_misc, mask, bth_dst_qp, clr);
 }
 
-static void dr_ste_copy_mask_spec(char *mask, struct mlx5dr_match_spec *spec)
+static void dr_ste_copy_mask_spec(char *mask, struct mlx5dr_match_spec *spec, bool clr)
 {
 	__be32 raw_ip[4];
 
-	spec->smac_47_16 = MLX5_GET(fte_match_set_lyr_2_4, mask, smac_47_16);
+	spec->smac_47_16 = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, smac_47_16, clr);
 
-	spec->smac_15_0 = MLX5_GET(fte_match_set_lyr_2_4, mask, smac_15_0);
-	spec->ethertype = MLX5_GET(fte_match_set_lyr_2_4, mask, ethertype);
+	spec->smac_15_0 = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, smac_15_0, clr);
+	spec->ethertype = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ethertype, clr);
 
-	spec->dmac_47_16 = MLX5_GET(fte_match_set_lyr_2_4, mask, dmac_47_16);
+	spec->dmac_47_16 = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, dmac_47_16, clr);
 
-	spec->dmac_15_0 = MLX5_GET(fte_match_set_lyr_2_4, mask, dmac_15_0);
-	spec->first_prio = MLX5_GET(fte_match_set_lyr_2_4, mask, first_prio);
-	spec->first_cfi = MLX5_GET(fte_match_set_lyr_2_4, mask, first_cfi);
-	spec->first_vid = MLX5_GET(fte_match_set_lyr_2_4, mask, first_vid);
-
-	spec->ip_protocol = MLX5_GET(fte_match_set_lyr_2_4, mask, ip_protocol);
-	spec->ip_dscp = MLX5_GET(fte_match_set_lyr_2_4, mask, ip_dscp);
-	spec->ip_ecn = MLX5_GET(fte_match_set_lyr_2_4, mask, ip_ecn);
-	spec->cvlan_tag = MLX5_GET(fte_match_set_lyr_2_4, mask, cvlan_tag);
-	spec->svlan_tag = MLX5_GET(fte_match_set_lyr_2_4, mask, svlan_tag);
-	spec->frag = MLX5_GET(fte_match_set_lyr_2_4, mask, frag);
-	spec->ip_version = MLX5_GET(fte_match_set_lyr_2_4, mask, ip_version);
-	spec->tcp_flags = MLX5_GET(fte_match_set_lyr_2_4, mask, tcp_flags);
-	spec->tcp_sport = MLX5_GET(fte_match_set_lyr_2_4, mask, tcp_sport);
-	spec->tcp_dport = MLX5_GET(fte_match_set_lyr_2_4, mask, tcp_dport);
-
-	spec->ttl_hoplimit = MLX5_GET(fte_match_set_lyr_2_4, mask, ttl_hoplimit);
-
-	spec->udp_sport = MLX5_GET(fte_match_set_lyr_2_4, mask, udp_sport);
-	spec->udp_dport = MLX5_GET(fte_match_set_lyr_2_4, mask, udp_dport);
-
-	memcpy(raw_ip, MLX5_ADDR_OF(fte_match_set_lyr_2_4, mask,
-				    src_ipv4_src_ipv6.ipv6_layout.ipv6),
-				    sizeof(raw_ip));
+	spec->dmac_15_0 = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, dmac_15_0, clr);
+	spec->first_prio = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, first_prio, clr);
+	spec->first_cfi = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, first_cfi, clr);
+	spec->first_vid = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, first_vid, clr);
+
+	spec->ip_protocol = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ip_protocol, clr);
+	spec->ip_dscp = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ip_dscp, clr);
+	spec->ip_ecn = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ip_ecn, clr);
+	spec->cvlan_tag = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, cvlan_tag, clr);
+	spec->svlan_tag = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, svlan_tag, clr);
+	spec->frag = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, frag, clr);
+	spec->ip_version = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ip_version, clr);
+	spec->tcp_flags = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, tcp_flags, clr);
+	spec->tcp_sport = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, tcp_sport, clr);
+	spec->tcp_dport = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, tcp_dport, clr);
+
+	spec->ipv4_ihl = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ipv4_ihl, clr);
+	spec->ttl_hoplimit = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, ttl_hoplimit, clr);
+
+	spec->udp_sport = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, udp_sport, clr);
+	spec->udp_dport = IFC_GET_CLR(fte_match_set_lyr_2_4, mask, udp_dport, clr);
+
+	memcpy_and_clear(raw_ip, MLX5_ADDR_OF(fte_match_set_lyr_2_4, mask,
+					      src_ipv4_src_ipv6.ipv6_layout.ipv6),
+			 sizeof(raw_ip), clr);
 
 	spec->src_ip_127_96 = be32_to_cpu(raw_ip[0]);
 	spec->src_ip_95_64 = be32_to_cpu(raw_ip[1]);
 	spec->src_ip_63_32 = be32_to_cpu(raw_ip[2]);
 	spec->src_ip_31_0 = be32_to_cpu(raw_ip[3]);
 
-	memcpy(raw_ip, MLX5_ADDR_OF(fte_match_set_lyr_2_4, mask,
-				    dst_ipv4_dst_ipv6.ipv6_layout.ipv6),
-				    sizeof(raw_ip));
+	memcpy_and_clear(raw_ip, MLX5_ADDR_OF(fte_match_set_lyr_2_4, mask,
+					      dst_ipv4_dst_ipv6.ipv6_layout.ipv6),
+			 sizeof(raw_ip), clr);
 
 	spec->dst_ip_127_96 = be32_to_cpu(raw_ip[0]);
 	spec->dst_ip_95_64 = be32_to_cpu(raw_ip[1]);
@@ -770,104 +819,125 @@
 	spec->dst_ip_31_0 = be32_to_cpu(raw_ip[3]);
 }
 
-static void dr_ste_copy_mask_misc2(char *mask, struct mlx5dr_match_misc2 *spec)
+static void dr_ste_copy_mask_misc2(char *mask, struct mlx5dr_match_misc2 *spec, bool clr)
 {
 	spec->outer_first_mpls_label =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls.mpls_label);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls.mpls_label, clr);
 	spec->outer_first_mpls_exp =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls.mpls_exp);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls.mpls_exp, clr);
 	spec->outer_first_mpls_s_bos =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls.mpls_s_bos);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls.mpls_s_bos, clr);
 	spec->outer_first_mpls_ttl =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls.mpls_ttl);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls.mpls_ttl, clr);
 	spec->inner_first_mpls_label =
-		MLX5_GET(fte_match_set_misc2, mask, inner_first_mpls.mpls_label);
+		IFC_GET_CLR(fte_match_set_misc2, mask, inner_first_mpls.mpls_label, clr);
 	spec->inner_first_mpls_exp =
-		MLX5_GET(fte_match_set_misc2, mask, inner_first_mpls.mpls_exp);
+		IFC_GET_CLR(fte_match_set_misc2, mask, inner_first_mpls.mpls_exp, clr);
 	spec->inner_first_mpls_s_bos =
-		MLX5_GET(fte_match_set_misc2, mask, inner_first_mpls.mpls_s_bos);
+		IFC_GET_CLR(fte_match_set_misc2, mask, inner_first_mpls.mpls_s_bos, clr);
 	spec->inner_first_mpls_ttl =
-		MLX5_GET(fte_match_set_misc2, mask, inner_first_mpls.mpls_ttl);
+		IFC_GET_CLR(fte_match_set_misc2, mask, inner_first_mpls.mpls_ttl, clr);
 	spec->outer_first_mpls_over_gre_label =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_label);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_label, clr);
 	spec->outer_first_mpls_over_gre_exp =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_exp);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_exp, clr);
 	spec->outer_first_mpls_over_gre_s_bos =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_s_bos);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_s_bos, clr);
 	spec->outer_first_mpls_over_gre_ttl =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_ttl);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_gre.mpls_ttl, clr);
 	spec->outer_first_mpls_over_udp_label =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_label);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_label, clr);
 	spec->outer_first_mpls_over_udp_exp =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_exp);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_exp, clr);
 	spec->outer_first_mpls_over_udp_s_bos =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_s_bos);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_s_bos, clr);
 	spec->outer_first_mpls_over_udp_ttl =
-		MLX5_GET(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_ttl);
-	spec->metadata_reg_c_7 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_7);
-	spec->metadata_reg_c_6 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_6);
-	spec->metadata_reg_c_5 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_5);
-	spec->metadata_reg_c_4 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_4);
-	spec->metadata_reg_c_3 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_3);
-	spec->metadata_reg_c_2 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_2);
-	spec->metadata_reg_c_1 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_1);
-	spec->metadata_reg_c_0 = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_c_0);
-	spec->metadata_reg_a = MLX5_GET(fte_match_set_misc2, mask, metadata_reg_a);
-}
-
-static void dr_ste_copy_mask_misc3(char *mask, struct mlx5dr_match_misc3 *spec)
-{
-	spec->inner_tcp_seq_num = MLX5_GET(fte_match_set_misc3, mask, inner_tcp_seq_num);
-	spec->outer_tcp_seq_num = MLX5_GET(fte_match_set_misc3, mask, outer_tcp_seq_num);
-	spec->inner_tcp_ack_num = MLX5_GET(fte_match_set_misc3, mask, inner_tcp_ack_num);
-	spec->outer_tcp_ack_num = MLX5_GET(fte_match_set_misc3, mask, outer_tcp_ack_num);
+		IFC_GET_CLR(fte_match_set_misc2, mask, outer_first_mpls_over_udp.mpls_ttl, clr);
+	spec->metadata_reg_c_7 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_7, clr);
+	spec->metadata_reg_c_6 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_6, clr);
+	spec->metadata_reg_c_5 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_5, clr);
+	spec->metadata_reg_c_4 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_4, clr);
+	spec->metadata_reg_c_3 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_3, clr);
+	spec->metadata_reg_c_2 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_2, clr);
+	spec->metadata_reg_c_1 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_1, clr);
+	spec->metadata_reg_c_0 = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_c_0, clr);
+	spec->metadata_reg_a = IFC_GET_CLR(fte_match_set_misc2, mask, metadata_reg_a, clr);
+}
+
+static void dr_ste_copy_mask_misc3(char *mask, struct mlx5dr_match_misc3 *spec, bool clr)
+{
+	spec->inner_tcp_seq_num = IFC_GET_CLR(fte_match_set_misc3, mask, inner_tcp_seq_num, clr);
+	spec->outer_tcp_seq_num = IFC_GET_CLR(fte_match_set_misc3, mask, outer_tcp_seq_num, clr);
+	spec->inner_tcp_ack_num = IFC_GET_CLR(fte_match_set_misc3, mask, inner_tcp_ack_num, clr);
+	spec->outer_tcp_ack_num = IFC_GET_CLR(fte_match_set_misc3, mask, outer_tcp_ack_num, clr);
 	spec->outer_vxlan_gpe_vni =
-		MLX5_GET(fte_match_set_misc3, mask, outer_vxlan_gpe_vni);
+		IFC_GET_CLR(fte_match_set_misc3, mask, outer_vxlan_gpe_vni, clr);
 	spec->outer_vxlan_gpe_next_protocol =
-		MLX5_GET(fte_match_set_misc3, mask, outer_vxlan_gpe_next_protocol);
+		IFC_GET_CLR(fte_match_set_misc3, mask, outer_vxlan_gpe_next_protocol, clr);
 	spec->outer_vxlan_gpe_flags =
-		MLX5_GET(fte_match_set_misc3, mask, outer_vxlan_gpe_flags);
-	spec->icmpv4_header_data = MLX5_GET(fte_match_set_misc3, mask, icmp_header_data);
+		IFC_GET_CLR(fte_match_set_misc3, mask, outer_vxlan_gpe_flags, clr);
+	spec->icmpv4_header_data = IFC_GET_CLR(fte_match_set_misc3, mask, icmp_header_data, clr);
 	spec->icmpv6_header_data =
-		MLX5_GET(fte_match_set_misc3, mask, icmpv6_header_data);
-	spec->icmpv4_type = MLX5_GET(fte_match_set_misc3, mask, icmp_type);
-	spec->icmpv4_code = MLX5_GET(fte_match_set_misc3, mask, icmp_code);
-	spec->icmpv6_type = MLX5_GET(fte_match_set_misc3, mask, icmpv6_type);
-	spec->icmpv6_code = MLX5_GET(fte_match_set_misc3, mask, icmpv6_code);
+		IFC_GET_CLR(fte_match_set_misc3, mask, icmpv6_header_data, clr);
+	spec->icmpv4_type = IFC_GET_CLR(fte_match_set_misc3, mask, icmp_type, clr);
+	spec->icmpv4_code = IFC_GET_CLR(fte_match_set_misc3, mask, icmp_code, clr);
+	spec->icmpv6_type = IFC_GET_CLR(fte_match_set_misc3, mask, icmpv6_type, clr);
+	spec->icmpv6_code = IFC_GET_CLR(fte_match_set_misc3, mask, icmpv6_code, clr);
 	spec->geneve_tlv_option_0_data =
-		MLX5_GET(fte_match_set_misc3, mask, geneve_tlv_option_0_data);
-	spec->gtpu_msg_flags = MLX5_GET(fte_match_set_misc3, mask, gtpu_msg_flags);
-	spec->gtpu_msg_type = MLX5_GET(fte_match_set_misc3, mask, gtpu_msg_type);
-	spec->gtpu_teid = MLX5_GET(fte_match_set_misc3, mask, gtpu_teid);
-	spec->gtpu_dw_0 = MLX5_GET(fte_match_set_misc3, mask, gtpu_dw_0);
-	spec->gtpu_dw_2 = MLX5_GET(fte_match_set_misc3, mask, gtpu_dw_2);
+		IFC_GET_CLR(fte_match_set_misc3, mask, geneve_tlv_option_0_data, clr);
+	spec->gtpu_teid = IFC_GET_CLR(fte_match_set_misc3, mask, gtpu_teid, clr);
+	spec->gtpu_msg_flags = IFC_GET_CLR(fte_match_set_misc3, mask, gtpu_msg_flags, clr);
+	spec->gtpu_msg_type = IFC_GET_CLR(fte_match_set_misc3, mask, gtpu_msg_type, clr);
+	spec->gtpu_dw_0 = IFC_GET_CLR(fte_match_set_misc3, mask, gtpu_dw_0, clr);
+	spec->gtpu_dw_2 = IFC_GET_CLR(fte_match_set_misc3, mask, gtpu_dw_2, clr);
 	spec->gtpu_first_ext_dw_0 =
-		MLX5_GET(fte_match_set_misc3, mask, gtpu_first_ext_dw_0);
+		IFC_GET_CLR(fte_match_set_misc3, mask, gtpu_first_ext_dw_0, clr);
 }
 
-static void dr_ste_copy_mask_misc4(char *mask, struct mlx5dr_match_misc4 *spec)
+static void dr_ste_copy_mask_misc4(char *mask, struct mlx5dr_match_misc4 *spec, bool clr)
 {
 	spec->prog_sample_field_id_0 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_id_0);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_id_0, clr);
 	spec->prog_sample_field_value_0 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_value_0);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_value_0, clr);
 	spec->prog_sample_field_id_1 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_id_1);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_id_1, clr);
 	spec->prog_sample_field_value_1 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_value_1);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_value_1, clr);
 	spec->prog_sample_field_id_2 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_id_2);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_id_2, clr);
 	spec->prog_sample_field_value_2 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_value_2);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_value_2, clr);
 	spec->prog_sample_field_id_3 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_id_3);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_id_3, clr);
 	spec->prog_sample_field_value_3 =
-		MLX5_GET(fte_match_set_misc4, mask, prog_sample_field_value_3);
+		IFC_GET_CLR(fte_match_set_misc4, mask, prog_sample_field_value_3, clr);
+}
+
+static void dr_ste_copy_mask_misc5(char *mask, struct mlx5dr_match_misc5 *spec, bool clr)
+{
+	spec->macsec_tag_0 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, macsec_tag_0, clr);
+	spec->macsec_tag_1 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, macsec_tag_1, clr);
+	spec->macsec_tag_2 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, macsec_tag_2, clr);
+	spec->macsec_tag_3 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, macsec_tag_3, clr);
+	spec->tunnel_header_0 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, tunnel_header_0, clr);
+	spec->tunnel_header_1 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, tunnel_header_1, clr);
+	spec->tunnel_header_2 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, tunnel_header_2, clr);
+	spec->tunnel_header_3 =
+		IFC_GET_CLR(fte_match_set_misc5, mask, tunnel_header_3, clr);
 }
 
 void mlx5dr_ste_copy_param(u8 match_criteria,
 			   struct mlx5dr_match_param *set_param,
-			   struct mlx5dr_match_parameters *mask)
+			   struct mlx5dr_match_parameters *mask,
+			   bool clr)
 {
 	u8 tail_param[MLX5_ST_SZ_BYTES(fte_match_set_lyr_2_4)] = {};
 	u8 *data = (u8 *)mask->match_buf;
@@ -881,7 +951,7 @@
 		} else {
 			buff = mask->match_buf;
 		}
-		dr_ste_copy_mask_spec(buff, &set_param->outer);
+		dr_ste_copy_mask_spec(buff, &set_param->outer, clr);
 	}
 	param_location = sizeof(struct mlx5dr_match_spec);
 
@@ -894,7 +964,7 @@
 		} else {
 			buff = data + param_location;
 		}
-		dr_ste_copy_mask_misc(buff, &set_param->misc);
+		dr_ste_copy_mask_misc(buff, &set_param->misc, clr);
 	}
 	param_location += sizeof(struct mlx5dr_match_misc);
 
@@ -907,7 +977,7 @@
 		} else {
 			buff = data + param_location;
 		}
-		dr_ste_copy_mask_spec(buff, &set_param->inner);
+		dr_ste_copy_mask_spec(buff, &set_param->inner, clr);
 	}
 	param_location += sizeof(struct mlx5dr_match_spec);
 
@@ -920,7 +990,7 @@
 		} else {
 			buff = data + param_location;
 		}
-		dr_ste_copy_mask_misc2(buff, &set_param->misc2);
+		dr_ste_copy_mask_misc2(buff, &set_param->misc2, clr);
 	}
 
 	param_location += sizeof(struct mlx5dr_match_misc2);
@@ -934,7 +1004,7 @@
 		} else {
 			buff = data + param_location;
 		}
-		dr_ste_copy_mask_misc3(buff, &set_param->misc3);
+		dr_ste_copy_mask_misc3(buff, &set_param->misc3, clr);
 	}
 
 	param_location += sizeof(struct mlx5dr_match_misc3);
@@ -948,7 +1018,21 @@
 		} else {
 			buff = data + param_location;
 		}
-		dr_ste_copy_mask_misc4(buff, &set_param->misc4);
+		dr_ste_copy_mask_misc4(buff, &set_param->misc4, clr);
+	}
+
+	param_location += sizeof(struct mlx5dr_match_misc4);
+
+	if (match_criteria & DR_MATCHER_CRITERIA_MISC5) {
+		if (mask->match_sz < param_location +
+		    sizeof(struct mlx5dr_match_misc5)) {
+			memcpy(tail_param, data + param_location,
+			       mask->match_sz - param_location);
+			buff = tail_param;
+		} else {
+			buff = data + param_location;
+		}
+		dr_ste_copy_mask_misc5(buff, &set_param->misc5, clr);
 	}
 }
 
@@ -1164,6 +1248,21 @@
 	ste_ctx->build_tnl_geneve_tlv_opt_init(sb, mask);
 }
 
+void mlx5dr_ste_build_tnl_geneve_tlv_opt_exist(struct mlx5dr_ste_ctx *ste_ctx,
+					       struct mlx5dr_ste_build *sb,
+					       struct mlx5dr_match_param *mask,
+					       struct mlx5dr_cmd_caps *caps,
+					       bool inner, bool rx)
+{
+	if (!ste_ctx->build_tnl_geneve_tlv_opt_exist_init)
+		return;
+
+	sb->rx = rx;
+	sb->caps = caps;
+	sb->inner = inner;
+	ste_ctx->build_tnl_geneve_tlv_opt_exist_init(sb, mask);
+}
+
 void mlx5dr_ste_build_tnl_gtpu(struct mlx5dr_ste_ctx *ste_ctx,
 			       struct mlx5dr_ste_build *sb,
 			       struct mlx5dr_match_param *mask,
@@ -1253,15 +1352,24 @@
 	ste_ctx->build_flex_parser_1_init(sb, mask);
 }
 
-static struct mlx5dr_ste_ctx *mlx5dr_ste_ctx_arr[] = {
-	[MLX5_STEERING_FORMAT_CONNECTX_5] = &ste_ctx_v0,
-	[MLX5_STEERING_FORMAT_CONNECTX_6DX] = &ste_ctx_v1,
-};
+void mlx5dr_ste_build_tnl_header_0_1(struct mlx5dr_ste_ctx *ste_ctx,
+				     struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask,
+				     bool inner, bool rx)
+{
+	sb->rx = rx;
+	sb->inner = inner;
+	ste_ctx->build_tnl_header_0_1_init(sb, mask);
+}
 
 struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx(u8 version)
 {
-	if (version > MLX5_STEERING_FORMAT_CONNECTX_6DX)
-		return NULL;
+	if (version == MLX5_STEERING_FORMAT_CONNECTX_5)
+		return mlx5dr_ste_get_ctx_v0();
+	else if (version == MLX5_STEERING_FORMAT_CONNECTX_6DX)
+		return mlx5dr_ste_get_ctx_v1();
+	else if (version == MLX5_STEERING_FORMAT_CONNECTX_7)
+		return mlx5dr_ste_get_ctx_v2();
 
-	return mlx5dr_ste_ctx_arr[version];
+	return NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.h
@@ -135,12 +135,14 @@
 	void DR_STE_CTX_BUILDER(tnl_vxlan_gpe);
 	void DR_STE_CTX_BUILDER(tnl_geneve);
 	void DR_STE_CTX_BUILDER(tnl_geneve_tlv_opt);
+	void DR_STE_CTX_BUILDER(tnl_geneve_tlv_opt_exist);
 	void DR_STE_CTX_BUILDER(register_0);
 	void DR_STE_CTX_BUILDER(register_1);
 	void DR_STE_CTX_BUILDER(src_gvmi_qpn);
 	void DR_STE_CTX_BUILDER(flex_parser_0);
 	void DR_STE_CTX_BUILDER(flex_parser_1);
 	void DR_STE_CTX_BUILDER(tnl_gtpu);
+	void DR_STE_CTX_BUILDER(tnl_header_0_1);
 	void DR_STE_CTX_BUILDER(tnl_gtpu_flex_parser_0);
 	void DR_STE_CTX_BUILDER(tnl_gtpu_flex_parser_1);
 
@@ -159,11 +161,13 @@
 	u32 actions_caps;
 	void (*set_actions_rx)(struct mlx5dr_domain *dmn,
 			       u8 *action_type_set,
+			       u32 actions_caps,
 			       u8 *hw_ste_arr,
 			       struct mlx5dr_ste_actions_attr *attr,
 			       u32 *added_stes);
 	void (*set_actions_tx)(struct mlx5dr_domain *dmn,
 			       u8 *action_type_set,
+			       u32 actions_caps,
 			       u8 *hw_ste_arr,
 			       struct mlx5dr_ste_actions_attr *attr,
 			       u32 *added_stes);
@@ -195,7 +199,8 @@
 	void (*prepare_for_postsend)(u8 *hw_ste_p, u32 ste_size);
 };
 
-extern struct mlx5dr_ste_ctx ste_ctx_v0;
-extern struct mlx5dr_ste_ctx ste_ctx_v1;
+struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx_v0(void);
+struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx_v1(void);
+struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx_v2(void);
 
 #endif  /* _DR_STE_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v0.c
@@ -80,6 +80,7 @@
 	DR_STE_V0_LU_TYPE_GENERAL_PURPOSE		= 0x18,
 	DR_STE_V0_LU_TYPE_STEERING_REGISTERS_0		= 0x2f,
 	DR_STE_V0_LU_TYPE_STEERING_REGISTERS_1		= 0x30,
+	DR_STE_V0_LU_TYPE_TUNNEL_HEADER			= 0x34,
 	DR_STE_V0_LU_TYPE_DONT_CARE			= MLX5DR_STE_LU_TYPE_DONT_CARE,
 };
 
@@ -407,6 +408,7 @@
 static void
 dr_ste_v0_set_actions_tx(struct mlx5dr_domain *dmn,
 			 u8 *action_type_set,
+			 u32 actions_caps,
 			 u8 *last_ste,
 			 struct mlx5dr_ste_actions_attr *attr,
 			 u32 *added_stes)
@@ -476,6 +478,7 @@
 static void
 dr_ste_v0_set_actions_rx(struct mlx5dr_domain *dmn,
 			 u8 *action_type_set,
+			 u32 actions_caps,
 			 u8 *last_ste,
 			 struct mlx5dr_ste_actions_attr *attr,
 			 u32 *added_stes)
@@ -1151,6 +1154,7 @@
 	struct mlx5dr_match_spec *spec = sb->inner ? &value->inner : &value->outer;
 
 	DR_STE_SET_TAG(eth_l3_ipv4_misc, tag, time_to_live, spec, ttl_hoplimit);
+	DR_STE_SET_TAG(eth_l3_ipv4_misc, tag, ihl, spec, ipv4_ihl);
 
 	return 0;
 }
@@ -1645,7 +1649,7 @@
 	struct mlx5dr_match_misc *misc = &value->misc;
 	struct mlx5dr_cmd_vport_cap *vport_cap;
 	struct mlx5dr_domain *dmn = sb->dmn;
-	struct mlx5dr_cmd_caps *caps;
+	struct mlx5dr_domain *vport_dmn;
 	u8 *bit_mask = sb->bit_mask;
 	bool source_gvmi_set;
 
@@ -1654,23 +1658,24 @@
 	if (sb->vhca_id_valid) {
 		/* Find port GVMI based on the eswitch_owner_vhca_id */
 		if (misc->source_eswitch_owner_vhca_id == dmn->info.caps.gvmi)
-			caps = &dmn->info.caps;
+			vport_dmn = dmn;
 		else if (dmn->peer_dmn && (misc->source_eswitch_owner_vhca_id ==
 					   dmn->peer_dmn->info.caps.gvmi))
-			caps = &dmn->peer_dmn->info.caps;
+			vport_dmn = dmn->peer_dmn;
 		else
 			return -EINVAL;
 
 		misc->source_eswitch_owner_vhca_id = 0;
 	} else {
-		caps = &dmn->info.caps;
+		vport_dmn = dmn;
 	}
 
 	source_gvmi_set = MLX5_GET(ste_src_gvmi_qp, bit_mask, source_gvmi);
 	if (source_gvmi_set) {
-		vport_cap = mlx5dr_get_vport_cap(caps, misc->source_port);
+		vport_cap = mlx5dr_domain_get_vport_cap(vport_dmn,
+							misc->source_port);
 		if (!vport_cap) {
-			mlx5dr_err(dmn, "Vport 0x%x is invalid\n",
+			mlx5dr_err(dmn, "Vport 0x%x is disabled or invalid\n",
 				   misc->source_port);
 			return -EINVAL;
 		}
@@ -1703,7 +1708,7 @@
 	u32 id = *misc4_field_id;
 	u8 *parser_ptr;
 
-	if (parser_is_used[id])
+	if (id >= DR_NUM_OF_FLEX_PARSERS || parser_is_used[id])
 		return;
 
 	parser_is_used[id] = true;
@@ -1874,7 +1879,28 @@
 	sb->ste_build_tag_func = &dr_ste_v0_build_tnl_gtpu_flex_parser_1_tag;
 }
 
-struct mlx5dr_ste_ctx ste_ctx_v0 = {
+static int dr_ste_v0_build_tnl_header_0_1_tag(struct mlx5dr_match_param *value,
+					      struct mlx5dr_ste_build *sb,
+					      uint8_t *tag)
+{
+	struct mlx5dr_match_misc5 *misc5 = &value->misc5;
+
+	DR_STE_SET_TAG(tunnel_header, tag, tunnel_header_0, misc5, tunnel_header_0);
+	DR_STE_SET_TAG(tunnel_header, tag, tunnel_header_1, misc5, tunnel_header_1);
+
+	return 0;
+}
+
+static void dr_ste_v0_build_tnl_header_0_1_init(struct mlx5dr_ste_build *sb,
+						struct mlx5dr_match_param *mask)
+{
+	sb->lu_type = DR_STE_V0_LU_TYPE_TUNNEL_HEADER;
+	dr_ste_v0_build_tnl_header_0_1_tag(mask, sb, sb->bit_mask);
+	sb->byte_mask = mlx5dr_ste_conv_bit_to_byte_mask(sb->bit_mask);
+	sb->ste_build_tag_func = &dr_ste_v0_build_tnl_header_0_1_tag;
+}
+
+static struct mlx5dr_ste_ctx ste_ctx_v0 = {
 	/* Builders */
 	.build_eth_l2_src_dst_init	= &dr_ste_v0_build_eth_l2_src_dst_init,
 	.build_eth_l3_ipv6_src_init	= &dr_ste_v0_build_eth_l3_ipv6_src_init,
@@ -1902,6 +1928,7 @@
 	.build_flex_parser_0_init	= &dr_ste_v0_build_flex_parser_0_init,
 	.build_flex_parser_1_init	= &dr_ste_v0_build_flex_parser_1_init,
 	.build_tnl_gtpu_init		= &dr_ste_v0_build_flex_parser_tnl_gtpu_init,
+	.build_tnl_header_0_1_init	= &dr_ste_v0_build_tnl_header_0_1_init,
 	.build_tnl_gtpu_flex_parser_0_init   = &dr_ste_v0_build_tnl_gtpu_flex_parser_0_init,
 	.build_tnl_gtpu_flex_parser_1_init   = &dr_ste_v0_build_tnl_gtpu_flex_parser_1_init,
 
@@ -1926,3 +1953,8 @@
 	.set_action_copy		= &dr_ste_v0_set_action_copy,
 	.set_action_decap_l3_list	= &dr_ste_v0_set_action_decap_l3_list,
 };
+
+struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx_v0(void)
+{
+	return &ste_ctx_v0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v1.c
@@ -3,7 +3,7 @@
 
 #include <linux/types.h>
 #include "mlx5_ifc_dr_ste_v1.h"
-#include "dr_ste.h"
+#include "dr_ste_v1.h"
 
 #define DR_STE_CALC_DFNR_TYPE(lookup_type, inner) \
 	((inner) ? DR_STE_V1_LU_TYPE_##lookup_type##_I : \
@@ -47,6 +47,7 @@
 	DR_STE_V1_LU_TYPE_ETHL3_IPV4_MISC_I		= 0x000f,
 	DR_STE_V1_LU_TYPE_STEERING_REGISTERS_0		= 0x010f,
 	DR_STE_V1_LU_TYPE_STEERING_REGISTERS_1		= 0x0110,
+	DR_STE_V1_LU_TYPE_FLEX_PARSER_OK		= 0x0011,
 	DR_STE_V1_LU_TYPE_FLEX_PARSER_0			= 0x0111,
 	DR_STE_V1_LU_TYPE_FLEX_PARSER_1			= 0x0112,
 	DR_STE_V1_LU_TYPE_ETHL4_MISC_O			= 0x0113,
@@ -120,12 +121,12 @@
 	DR_STE_V1_ACTION_MDFY_FLD_CFG_HDR_0_1		= 0x70,
 	DR_STE_V1_ACTION_MDFY_FLD_METADATA_2_CQE	= 0x7b,
 	DR_STE_V1_ACTION_MDFY_FLD_GNRL_PURPOSE		= 0x7c,
-	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_2		= 0x8c,
-	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_3		= 0x8d,
-	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_4		= 0x8e,
-	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_5		= 0x8f,
-	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_6		= 0x90,
-	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_7		= 0x91,
+	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_2_0		= 0x8c,
+	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_2_1		= 0x8d,
+	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_1_0		= 0x8e,
+	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_1_1		= 0x8f,
+	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_0_0		= 0x90,
+	DR_STE_V1_ACTION_MDFY_FLD_REGISTER_0_1		= 0x91,
 };
 
 static const struct mlx5dr_ste_action_modify_field dr_ste_v1_action_modify_field_arr[] = {
@@ -222,22 +223,22 @@
 		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_METADATA_2_CQE, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_0] = {
-		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_6, .start = 0, .end = 31,
+		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_0_0, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_1] = {
-		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_7, .start = 0, .end = 31,
+		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_0_1, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_2] = {
-		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_4, .start = 0, .end = 31,
+		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_1_0, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_3] = {
-		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_5, .start = 0, .end = 31,
+		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_1_1, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_4] = {
-		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_2, .start = 0, .end = 31,
+		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_2_0, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_5] = {
-		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_3, .start = 0, .end = 31,
+		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_REGISTER_2_1, .start = 0, .end = 31,
 	},
 	[MLX5_ACTION_IN_FIELD_OUT_TCP_SEQ_NUM] = {
 		.hw_field = DR_STE_V1_ACTION_MDFY_FLD_TCP_MISC_0, .start = 0, .end = 31,
@@ -261,7 +262,7 @@
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, entry_format, entry_type);
 }
 
-static void dr_ste_v1_set_miss_addr(u8 *hw_ste_p, u64 miss_addr)
+void dr_ste_v1_set_miss_addr(u8 *hw_ste_p, u64 miss_addr)
 {
 	u64 index = miss_addr >> 6;
 
@@ -269,7 +270,7 @@
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, miss_address_31_6, index);
 }
 
-static u64 dr_ste_v1_get_miss_addr(u8 *hw_ste_p)
+u64 dr_ste_v1_get_miss_addr(u8 *hw_ste_p)
 {
 	u64 index =
 		((u64)MLX5_GET(ste_match_bwc_v1, hw_ste_p, miss_address_31_6) |
@@ -278,12 +279,12 @@
 	return index << 6;
 }
 
-static void dr_ste_v1_set_byte_mask(u8 *hw_ste_p, u16 byte_mask)
+void dr_ste_v1_set_byte_mask(u8 *hw_ste_p, u16 byte_mask)
 {
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, byte_mask, byte_mask);
 }
 
-static u16 dr_ste_v1_get_byte_mask(u8 *hw_ste_p)
+u16 dr_ste_v1_get_byte_mask(u8 *hw_ste_p)
 {
 	return MLX5_GET(ste_match_bwc_v1, hw_ste_p, byte_mask);
 }
@@ -294,13 +295,13 @@
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, match_definer_ctx_idx, lu_type & 0xFF);
 }
 
-static void dr_ste_v1_set_next_lu_type(u8 *hw_ste_p, u16 lu_type)
+void dr_ste_v1_set_next_lu_type(u8 *hw_ste_p, u16 lu_type)
 {
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, next_entry_format, lu_type >> 8);
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, hash_definer_ctx_idx, lu_type & 0xFF);
 }
 
-static u16 dr_ste_v1_get_next_lu_type(u8 *hw_ste_p)
+u16 dr_ste_v1_get_next_lu_type(u8 *hw_ste_p)
 {
 	u8 mode = MLX5_GET(ste_match_bwc_v1, hw_ste_p, next_entry_format);
 	u8 index = MLX5_GET(ste_match_bwc_v1, hw_ste_p, hash_definer_ctx_idx);
@@ -313,7 +314,7 @@
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, next_table_base_63_48, gvmi);
 }
 
-static void dr_ste_v1_set_hit_addr(u8 *hw_ste_p, u64 icm_addr, u32 ht_size)
+void dr_ste_v1_set_hit_addr(u8 *hw_ste_p, u64 icm_addr, u32 ht_size)
 {
 	u64 index = (icm_addr >> 5) | ht_size;
 
@@ -321,8 +322,7 @@
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, next_table_base_31_5_size, index);
 }
 
-static void dr_ste_v1_init(u8 *hw_ste_p, u16 lu_type,
-			   bool is_rx, u16 gvmi)
+void dr_ste_v1_init(u8 *hw_ste_p, u16 lu_type, bool is_rx, u16 gvmi)
 {
 	dr_ste_v1_set_lu_type(hw_ste_p, lu_type);
 	dr_ste_v1_set_next_lu_type(hw_ste_p, MLX5DR_STE_LU_TYPE_DONT_CARE);
@@ -332,8 +332,7 @@
 	MLX5_SET(ste_match_bwc_v1, hw_ste_p, miss_address_63_48, gvmi);
 }
 
-static void dr_ste_v1_prepare_for_postsend(u8 *hw_ste_p,
-					   u32 ste_size)
+void dr_ste_v1_prepare_for_postsend(u8 *hw_ste_p, u32 ste_size)
 {
 	u8 *tag = hw_ste_p + DR_STE_SIZE_CTRL;
 	u8 *mask = tag + DR_STE_SIZE_TAG;
@@ -510,11 +509,12 @@
 	memset(action, 0, MLX5_FLD_SZ_BYTES(ste_mask_and_match_v1, action));
 }
 
-static void dr_ste_v1_set_actions_tx(struct mlx5dr_domain *dmn,
-				     u8 *action_type_set,
-				     u8 *last_ste,
-				     struct mlx5dr_ste_actions_attr *attr,
-				     u32 *added_stes)
+void dr_ste_v1_set_actions_tx(struct mlx5dr_domain *dmn,
+			      u8 *action_type_set,
+			      u32 actions_caps,
+			      u8 *last_ste,
+			      struct mlx5dr_ste_actions_attr *attr,
+			      u32 *added_stes)
 {
 	u8 *action = MLX5_ADDR_OF(ste_match_bwc_v1, last_ste, action);
 	u8 action_sz = DR_STE_ACTION_DOUBLE_SZ;
@@ -532,7 +532,10 @@
 		dr_ste_v1_set_pop_vlan(last_ste, action, attr->vlans.count);
 		action_sz -= DR_STE_ACTION_SINGLE_SZ;
 		action += DR_STE_ACTION_SINGLE_SZ;
-		allow_modify_hdr = false;
+
+		/* Check if vlan_pop and modify_hdr on same STE is supported */
+		if (!(actions_caps & DR_STE_CTX_ACTION_CAP_POP_MDFY))
+			allow_modify_hdr = false;
 	}
 
 	if (action_type_set[DR_ACTION_TYP_CTR])
@@ -586,9 +589,11 @@
 	} else if (action_type_set[DR_ACTION_TYP_L2_TO_TNL_L3]) {
 		u8 *d_action;
 
-		dr_ste_v1_arr_init_next_match(&last_ste, added_stes, attr->gvmi);
-		action = MLX5_ADDR_OF(ste_mask_and_match_v1, last_ste, action);
-		action_sz = DR_STE_ACTION_TRIPLE_SZ;
+		if (action_sz < DR_STE_ACTION_TRIPLE_SZ) {
+			dr_ste_v1_arr_init_next_match(&last_ste, added_stes, attr->gvmi);
+			action = MLX5_ADDR_OF(ste_mask_and_match_v1, last_ste, action);
+			action_sz = DR_STE_ACTION_TRIPLE_SZ;
+		}
 		d_action = action + DR_STE_ACTION_SINGLE_SZ;
 
 		dr_ste_v1_set_encap_l3(last_ste,
@@ -628,11 +633,12 @@
 	dr_ste_v1_set_hit_addr(last_ste, attr->final_icm_addr, 1);
 }
 
-static void dr_ste_v1_set_actions_rx(struct mlx5dr_domain *dmn,
-				     u8 *action_type_set,
-				     u8 *last_ste,
-				     struct mlx5dr_ste_actions_attr *attr,
-				     u32 *added_stes)
+void dr_ste_v1_set_actions_rx(struct mlx5dr_domain *dmn,
+			      u8 *action_type_set,
+			      u32 actions_caps,
+			      u8 *last_ste,
+			      struct mlx5dr_ste_actions_attr *attr,
+			      u32 *added_stes)
 {
 	u8 *action = MLX5_ADDR_OF(ste_match_bwc_v1, last_ste, action);
 	u8 action_sz = DR_STE_ACTION_DOUBLE_SZ;
@@ -674,13 +680,16 @@
 			dr_ste_v1_arr_init_next_match(&last_ste, added_stes, attr->gvmi);
 			action = MLX5_ADDR_OF(ste_mask_and_match_v1, last_ste, action);
 			action_sz = DR_STE_ACTION_TRIPLE_SZ;
-			allow_modify_hdr = false;
-			allow_ctr = false;
 		}
 
 		dr_ste_v1_set_pop_vlan(last_ste, action, attr->vlans.count);
 		action_sz -= DR_STE_ACTION_SINGLE_SZ;
 		action += DR_STE_ACTION_SINGLE_SZ;
+		allow_ctr = false;
+
+		/* Check if vlan_pop and modify_hdr on same STE is supported */
+		if (!(actions_caps & DR_STE_CTX_ACTION_CAP_POP_MDFY))
+			allow_modify_hdr = false;
 	}
 
 	if (action_type_set[DR_ACTION_TYP_MODIFY_HDR]) {
@@ -728,9 +737,9 @@
 			action = MLX5_ADDR_OF(ste_mask_and_match_v1, last_ste, action);
 			action_sz = DR_STE_ACTION_TRIPLE_SZ;
 			allow_modify_hdr = true;
-			allow_ctr = false;
 		}
 		dr_ste_v1_set_counter_id(last_ste, attr->ctr_id);
+		allow_ctr = false;
 	}
 
 	if (action_type_set[DR_ACTION_TYP_L2_TO_TNL_L2]) {
@@ -797,11 +806,11 @@
 	dr_ste_v1_set_hit_addr(last_ste, attr->final_icm_addr, 1);
 }
 
-static void dr_ste_v1_set_action_set(u8 *d_action,
-				     u8 hw_field,
-				     u8 shifter,
-				     u8 length,
-				     u32 data)
+void dr_ste_v1_set_action_set(u8 *d_action,
+			      u8 hw_field,
+			      u8 shifter,
+			      u8 length,
+			      u32 data)
 {
 	shifter += MLX5_MODIFY_HEADER_V1_QW_OFFSET;
 	MLX5_SET(ste_double_action_set_v1, d_action, action_id, DR_STE_V1_ACTION_ID_SET);
@@ -811,11 +820,11 @@
 	MLX5_SET(ste_double_action_set_v1, d_action, inline_data, data);
 }
 
-static void dr_ste_v1_set_action_add(u8 *d_action,
-				     u8 hw_field,
-				     u8 shifter,
-				     u8 length,
-				     u32 data)
+void dr_ste_v1_set_action_add(u8 *d_action,
+			      u8 hw_field,
+			      u8 shifter,
+			      u8 length,
+			      u32 data)
 {
 	shifter += MLX5_MODIFY_HEADER_V1_QW_OFFSET;
 	MLX5_SET(ste_double_action_add_v1, d_action, action_id, DR_STE_V1_ACTION_ID_ADD);
@@ -825,12 +834,12 @@
 	MLX5_SET(ste_double_action_add_v1, d_action, add_value, data);
 }
 
-static void dr_ste_v1_set_action_copy(u8 *d_action,
-				      u8 dst_hw_field,
-				      u8 dst_shifter,
-				      u8 dst_len,
-				      u8 src_hw_field,
-				      u8 src_shifter)
+void dr_ste_v1_set_action_copy(u8 *d_action,
+			       u8 dst_hw_field,
+			       u8 dst_shifter,
+			       u8 dst_len,
+			       u8 src_hw_field,
+			       u8 src_shifter)
 {
 	dst_shifter += MLX5_MODIFY_HEADER_V1_QW_OFFSET;
 	src_shifter += MLX5_MODIFY_HEADER_V1_QW_OFFSET;
@@ -845,11 +854,11 @@
 #define DR_STE_DECAP_L3_ACTION_NUM	8
 #define DR_STE_L2_HDR_MAX_SZ		20
 
-static int dr_ste_v1_set_action_decap_l3_list(void *data,
-					      u32 data_sz,
-					      u8 *hw_action,
-					      u32 hw_action_sz,
-					      u16 *used_hw_action_num)
+int dr_ste_v1_set_action_decap_l3_list(void *data,
+				       u32 data_sz,
+				       u8 *hw_action,
+				       u32 hw_action_sz,
+				       u16 *used_hw_action_num)
 {
 	u8 padded_data[DR_STE_L2_HDR_MAX_SZ] = {};
 	void *data_ptr = padded_data;
@@ -974,8 +983,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l2_src_dst_init(struct mlx5dr_ste_build *sb,
-						struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l2_src_dst_init(struct mlx5dr_ste_build *sb,
+					 struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l2_src_dst_bit_mask(mask, sb->inner, sb->bit_mask);
 
@@ -998,8 +1007,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l3_ipv6_dst_init(struct mlx5dr_ste_build *sb,
-						 struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l3_ipv6_dst_init(struct mlx5dr_ste_build *sb,
+					  struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l3_ipv6_dst_tag(mask, sb, sb->bit_mask);
 
@@ -1022,8 +1031,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l3_ipv6_src_init(struct mlx5dr_ste_build *sb,
-						 struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l3_ipv6_src_init(struct mlx5dr_ste_build *sb,
+					  struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l3_ipv6_src_tag(mask, sb, sb->bit_mask);
 
@@ -1057,8 +1066,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l3_ipv4_5_tuple_init(struct mlx5dr_ste_build *sb,
-						     struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l3_ipv4_5_tuple_init(struct mlx5dr_ste_build *sb,
+					      struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l3_ipv4_5_tuple_tag(mask, sb, sb->bit_mask);
 
@@ -1076,8 +1085,8 @@
 	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, first_vlan_id, mask, first_vid);
 	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, first_cfi, mask, first_cfi);
 	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, first_priority, mask, first_prio);
-	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, ip_fragmented, mask, frag); // ?
-	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, l3_ethertype, mask, ethertype); // ?
+	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, ip_fragmented, mask, frag);
+	DR_STE_SET_TAG(eth_l2_src_v1, bit_mask, l3_ethertype, mask, ethertype);
 	DR_STE_SET_ONES(eth_l2_src_v1, bit_mask, l3_type, mask, ip_version);
 
 	if (mask->svlan_tag || mask->cvlan_tag) {
@@ -1198,8 +1207,8 @@
 	return dr_ste_v1_build_eth_l2_src_or_dst_tag(value, sb->inner, tag);
 }
 
-static void dr_ste_v1_build_eth_l2_src_init(struct mlx5dr_ste_build *sb,
-					    struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l2_src_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l2_src_bit_mask(mask, sb->inner, sb->bit_mask);
 
@@ -1231,8 +1240,8 @@
 	return dr_ste_v1_build_eth_l2_src_or_dst_tag(value, sb->inner, tag);
 }
 
-static void dr_ste_v1_build_eth_l2_dst_init(struct mlx5dr_ste_build *sb,
-					    struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l2_dst_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l2_dst_bit_mask(mask, sb->inner, sb->bit_mask);
 
@@ -1311,8 +1320,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l2_tnl_init(struct mlx5dr_ste_build *sb,
-					    struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l2_tnl_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l2_tnl_bit_mask(mask, sb->inner, sb->bit_mask);
 
@@ -1328,12 +1337,13 @@
 	struct mlx5dr_match_spec *spec = sb->inner ? &value->inner : &value->outer;
 
 	DR_STE_SET_TAG(eth_l3_ipv4_misc_v1, tag, time_to_live, spec, ttl_hoplimit);
+	DR_STE_SET_TAG(eth_l3_ipv4_misc_v1, tag, ihl, spec, ipv4_ihl);
 
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l3_ipv4_misc_init(struct mlx5dr_ste_build *sb,
-						  struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l3_ipv4_misc_init(struct mlx5dr_ste_build *sb,
+					   struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l3_ipv4_misc_tag(mask, sb, sb->bit_mask);
 
@@ -1372,8 +1382,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_ipv6_l3_l4_init(struct mlx5dr_ste_build *sb,
-						struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_ipv6_l3_l4_init(struct mlx5dr_ste_build *sb,
+					 struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_ipv6_l3_l4_tag(mask, sb, sb->bit_mask);
 
@@ -1396,8 +1406,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_mpls_init(struct mlx5dr_ste_build *sb,
-				      struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_mpls_init(struct mlx5dr_ste_build *sb,
+			       struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_mpls_tag(mask, sb, sb->bit_mask);
 
@@ -1423,8 +1433,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_tnl_gre_init(struct mlx5dr_ste_build *sb,
-					 struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_tnl_gre_init(struct mlx5dr_ste_build *sb,
+				  struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_tnl_gre_tag(mask, sb, sb->bit_mask);
 
@@ -1468,8 +1478,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_tnl_mpls_init(struct mlx5dr_ste_build *sb,
-					  struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_tnl_mpls_init(struct mlx5dr_ste_build *sb,
+				   struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_tnl_mpls_tag(mask, sb, sb->bit_mask);
 
@@ -1503,8 +1513,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_tnl_mpls_over_udp_init(struct mlx5dr_ste_build *sb,
-						   struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_tnl_mpls_over_udp_init(struct mlx5dr_ste_build *sb,
+					    struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_tnl_mpls_over_udp_tag(mask, sb, sb->bit_mask);
 
@@ -1544,8 +1554,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_tnl_mpls_over_gre_init(struct mlx5dr_ste_build *sb,
-						   struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_tnl_mpls_over_gre_init(struct mlx5dr_ste_build *sb,
+					    struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_tnl_mpls_over_gre_tag(mask, sb, sb->bit_mask);
 
@@ -1591,8 +1601,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_icmp_init(struct mlx5dr_ste_build *sb,
-				      struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_icmp_init(struct mlx5dr_ste_build *sb,
+			       struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_icmp_tag(mask, sb, sb->bit_mask);
 
@@ -1613,8 +1623,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_general_purpose_init(struct mlx5dr_ste_build *sb,
-						 struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_general_purpose_init(struct mlx5dr_ste_build *sb,
+					  struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_general_purpose_tag(mask, sb, sb->bit_mask);
 
@@ -1640,8 +1650,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_eth_l4_misc_init(struct mlx5dr_ste_build *sb,
-					     struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_eth_l4_misc_init(struct mlx5dr_ste_build *sb,
+				      struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_eth_l4_misc_tag(mask, sb, sb->bit_mask);
 
@@ -1670,9 +1680,8 @@
 	return 0;
 }
 
-static void
-dr_ste_v1_build_flex_parser_tnl_vxlan_gpe_init(struct mlx5dr_ste_build *sb,
-					       struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_flex_parser_tnl_vxlan_gpe_init(struct mlx5dr_ste_build *sb,
+						    struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_flex_parser_tnl_vxlan_gpe_tag(mask, sb, sb->bit_mask);
 
@@ -1700,9 +1709,8 @@
 	return 0;
 }
 
-static void
-dr_ste_v1_build_flex_parser_tnl_geneve_init(struct mlx5dr_ste_build *sb,
-					    struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_flex_parser_tnl_geneve_init(struct mlx5dr_ste_build *sb,
+						 struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_flex_parser_tnl_geneve_tag(mask, sb, sb->bit_mask);
 
@@ -1711,6 +1719,27 @@
 	sb->ste_build_tag_func = &dr_ste_v1_build_flex_parser_tnl_geneve_tag;
 }
 
+static int dr_ste_v1_build_tnl_header_0_1_tag(struct mlx5dr_match_param *value,
+					      struct mlx5dr_ste_build *sb,
+					      uint8_t *tag)
+{
+	struct mlx5dr_match_misc5 *misc5 = &value->misc5;
+
+	DR_STE_SET_TAG(tunnel_header, tag, tunnel_header_0, misc5, tunnel_header_0);
+	DR_STE_SET_TAG(tunnel_header, tag, tunnel_header_1, misc5, tunnel_header_1);
+
+	return 0;
+}
+
+void dr_ste_v1_build_tnl_header_0_1_init(struct mlx5dr_ste_build *sb,
+					 struct mlx5dr_match_param *mask)
+{
+	sb->lu_type = DR_STE_V1_LU_TYPE_FLEX_PARSER_TNL_HEADER;
+	dr_ste_v1_build_tnl_header_0_1_tag(mask, sb, sb->bit_mask);
+	sb->byte_mask = mlx5dr_ste_conv_bit_to_byte_mask(sb->bit_mask);
+	sb->ste_build_tag_func = &dr_ste_v1_build_tnl_header_0_1_tag;
+}
+
 static int dr_ste_v1_build_register_0_tag(struct mlx5dr_match_param *value,
 					  struct mlx5dr_ste_build *sb,
 					  u8 *tag)
@@ -1725,8 +1754,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_register_0_init(struct mlx5dr_ste_build *sb,
-					    struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_register_0_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_register_0_tag(mask, sb, sb->bit_mask);
 
@@ -1749,8 +1778,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_register_1_init(struct mlx5dr_ste_build *sb,
-					    struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_register_1_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_register_1_tag(mask, sb, sb->bit_mask);
 
@@ -1776,7 +1805,7 @@
 	struct mlx5dr_match_misc *misc = &value->misc;
 	struct mlx5dr_cmd_vport_cap *vport_cap;
 	struct mlx5dr_domain *dmn = sb->dmn;
-	struct mlx5dr_cmd_caps *caps;
+	struct mlx5dr_domain *vport_dmn;
 	u8 *bit_mask = sb->bit_mask;
 
 	DR_STE_SET_TAG(src_gvmi_qp_v1, tag, source_qp, misc, source_sqn);
@@ -1784,22 +1813,22 @@
 	if (sb->vhca_id_valid) {
 		/* Find port GVMI based on the eswitch_owner_vhca_id */
 		if (misc->source_eswitch_owner_vhca_id == dmn->info.caps.gvmi)
-			caps = &dmn->info.caps;
+			vport_dmn = dmn;
 		else if (dmn->peer_dmn && (misc->source_eswitch_owner_vhca_id ==
 					   dmn->peer_dmn->info.caps.gvmi))
-			caps = &dmn->peer_dmn->info.caps;
+			vport_dmn = dmn->peer_dmn;
 		else
 			return -EINVAL;
 
 		 misc->source_eswitch_owner_vhca_id = 0;
 	} else {
-		caps = &dmn->info.caps;
+		vport_dmn = dmn;
 	}
 
 	if (!MLX5_GET(ste_src_gvmi_qp_v1, bit_mask, source_gvmi))
 		return 0;
 
-	vport_cap = mlx5dr_get_vport_cap(caps, misc->source_port);
+	vport_cap = mlx5dr_domain_get_vport_cap(vport_dmn, misc->source_port);
 	if (!vport_cap) {
 		mlx5dr_err(dmn, "Vport 0x%x is disabled or invalid\n",
 			   misc->source_port);
@@ -1813,8 +1842,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_src_gvmi_qpn_init(struct mlx5dr_ste_build *sb,
-					      struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_src_gvmi_qpn_init(struct mlx5dr_ste_build *sb,
+				       struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_src_gvmi_qpn_bit_mask(mask, sb->bit_mask);
 
@@ -1831,7 +1860,7 @@
 	u32 id = *misc4_field_id;
 	u8 *parser_ptr;
 
-	if (parser_is_used[id])
+	if (id >= DR_NUM_OF_FLEX_PARSERS || parser_is_used[id])
 		return;
 
 	parser_is_used[id] = true;
@@ -1868,8 +1897,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_flex_parser_0_init(struct mlx5dr_ste_build *sb,
-					       struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_flex_parser_0_init(struct mlx5dr_ste_build *sb,
+					struct mlx5dr_match_param *mask)
 {
 	sb->lu_type = DR_STE_V1_LU_TYPE_FLEX_PARSER_0;
 	dr_ste_v1_build_felx_parser_tag(mask, sb, sb->bit_mask);
@@ -1877,8 +1906,8 @@
 	sb->ste_build_tag_func = &dr_ste_v1_build_felx_parser_tag;
 }
 
-static void dr_ste_v1_build_flex_parser_1_init(struct mlx5dr_ste_build *sb,
-					       struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_flex_parser_1_init(struct mlx5dr_ste_build *sb,
+					struct mlx5dr_match_param *mask)
 {
 	sb->lu_type = DR_STE_V1_LU_TYPE_FLEX_PARSER_1;
 	dr_ste_v1_build_felx_parser_tag(mask, sb, sb->bit_mask);
@@ -1902,7 +1931,7 @@
 	return 0;
 }
 
-static void
+void
 dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_init(struct mlx5dr_ste_build *sb,
 						    struct mlx5dr_match_param *mask)
 {
@@ -1919,6 +1948,32 @@
 	sb->ste_build_tag_func = &dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_tag;
 }
 
+static int
+dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_tag(struct mlx5dr_match_param *value,
+							 struct mlx5dr_ste_build *sb,
+							 uint8_t *tag)
+{
+	u8 parser_id = sb->caps->flex_parser_id_geneve_tlv_option_0;
+	struct mlx5dr_match_misc *misc = &value->misc;
+
+	if (misc->geneve_tlv_option_0_exist) {
+		MLX5_SET(ste_flex_parser_ok, tag, flex_parsers_ok, 1 << parser_id);
+		misc->geneve_tlv_option_0_exist = 0;
+	}
+
+	return 0;
+}
+
+void
+dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_init(struct mlx5dr_ste_build *sb,
+							  struct mlx5dr_match_param *mask)
+{
+	sb->lu_type = DR_STE_V1_LU_TYPE_FLEX_PARSER_OK;
+	dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_tag(mask, sb, sb->bit_mask);
+	sb->byte_mask = mlx5dr_ste_conv_bit_to_byte_mask(sb->bit_mask);
+	sb->ste_build_tag_func = &dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_tag;
+}
+
 static int dr_ste_v1_build_flex_parser_tnl_gtpu_tag(struct mlx5dr_match_param *value,
 						    struct mlx5dr_ste_build *sb,
 						    u8 *tag)
@@ -1932,8 +1987,8 @@
 	return 0;
 }
 
-static void dr_ste_v1_build_flex_parser_tnl_gtpu_init(struct mlx5dr_ste_build *sb,
-						      struct mlx5dr_match_param *mask)
+void dr_ste_v1_build_flex_parser_tnl_gtpu_init(struct mlx5dr_ste_build *sb,
+					       struct mlx5dr_match_param *mask)
 {
 	dr_ste_v1_build_flex_parser_tnl_gtpu_tag(mask, sb, sb->bit_mask);
 
@@ -1958,7 +2013,7 @@
 	return 0;
 }
 
-static void
+void
 dr_ste_v1_build_tnl_gtpu_flex_parser_0_init(struct mlx5dr_ste_build *sb,
 					    struct mlx5dr_match_param *mask)
 {
@@ -1985,7 +2040,7 @@
 	return 0;
 }
 
-static void
+void
 dr_ste_v1_build_tnl_gtpu_flex_parser_1_init(struct mlx5dr_ste_build *sb,
 					    struct mlx5dr_match_param *mask)
 {
@@ -1996,7 +2051,7 @@
 	sb->ste_build_tag_func = &dr_ste_v1_build_tnl_gtpu_flex_parser_1_tag;
 }
 
-struct mlx5dr_ste_ctx ste_ctx_v1 = {
+static struct mlx5dr_ste_ctx ste_ctx_v1 = {
 	/* Builders */
 	.build_eth_l2_src_dst_init	= &dr_ste_v1_build_eth_l2_src_dst_init,
 	.build_eth_l3_ipv6_src_init	= &dr_ste_v1_build_eth_l3_ipv6_src_init,
@@ -2018,12 +2073,14 @@
 	.build_tnl_vxlan_gpe_init	= &dr_ste_v1_build_flex_parser_tnl_vxlan_gpe_init,
 	.build_tnl_geneve_init		= &dr_ste_v1_build_flex_parser_tnl_geneve_init,
 	.build_tnl_geneve_tlv_opt_init	= &dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_init,
+	.build_tnl_geneve_tlv_opt_exist_init = &dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_init,
 	.build_register_0_init		= &dr_ste_v1_build_register_0_init,
 	.build_register_1_init		= &dr_ste_v1_build_register_1_init,
 	.build_src_gvmi_qpn_init	= &dr_ste_v1_build_src_gvmi_qpn_init,
 	.build_flex_parser_0_init	= &dr_ste_v1_build_flex_parser_0_init,
 	.build_flex_parser_1_init	= &dr_ste_v1_build_flex_parser_1_init,
 	.build_tnl_gtpu_init		= &dr_ste_v1_build_flex_parser_tnl_gtpu_init,
+	.build_tnl_header_0_1_init	= &dr_ste_v1_build_tnl_header_0_1_init,
 	.build_tnl_gtpu_flex_parser_0_init = &dr_ste_v1_build_tnl_gtpu_flex_parser_0_init,
 	.build_tnl_gtpu_flex_parser_1_init = &dr_ste_v1_build_tnl_gtpu_flex_parser_1_init,
 
@@ -2039,7 +2096,8 @@
 	/* Actions */
 	.actions_caps			= DR_STE_CTX_ACTION_CAP_TX_POP |
 					  DR_STE_CTX_ACTION_CAP_RX_PUSH |
-					  DR_STE_CTX_ACTION_CAP_RX_ENCAP,
+					  DR_STE_CTX_ACTION_CAP_RX_ENCAP |
+					  DR_STE_CTX_ACTION_CAP_POP_MDFY,
 	.set_actions_rx			= &dr_ste_v1_set_actions_rx,
 	.set_actions_tx			= &dr_ste_v1_set_actions_tx,
 	.modify_field_arr_sz		= ARRAY_SIZE(dr_ste_v1_action_modify_field_arr),
@@ -2051,3 +2109,8 @@
 	/* Send */
 	.prepare_for_postsend		= &dr_ste_v1_prepare_for_postsend,
 };
+
+struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx_v1(void)
+{
+	return &ste_ctx_v1;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v1.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v1.h
@@ -0,0 +1,94 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB */
+/* Copyright (c) 2022, NVIDIA CORPORATION & AFFILIATES. All rights reserved. */
+
+#ifndef	_DR_STE_V1_
+#define	_DR_STE_V1_
+
+#include "dr_types.h"
+#include "dr_ste.h"
+
+void dr_ste_v1_set_miss_addr(u8 *hw_ste_p, u64 miss_addr);
+u64 dr_ste_v1_get_miss_addr(u8 *hw_ste_p);
+void dr_ste_v1_set_byte_mask(u8 *hw_ste_p, u16 byte_mask);
+u16 dr_ste_v1_get_byte_mask(u8 *hw_ste_p);
+void dr_ste_v1_set_next_lu_type(u8 *hw_ste_p, u16 lu_type);
+u16 dr_ste_v1_get_next_lu_type(u8 *hw_ste_p);
+void dr_ste_v1_set_hit_addr(u8 *hw_ste_p, u64 icm_addr, u32 ht_size);
+void dr_ste_v1_init(u8 *hw_ste_p, u16 lu_type, bool is_rx, u16 gvmi);
+void dr_ste_v1_prepare_for_postsend(u8 *hw_ste_p, u32 ste_size);
+void dr_ste_v1_set_actions_tx(struct mlx5dr_domain *dmn, u8 *action_type_set,
+			      u32 actions_caps, u8 *last_ste,
+			      struct mlx5dr_ste_actions_attr *attr, u32 *added_stes);
+void dr_ste_v1_set_actions_rx(struct mlx5dr_domain *dmn, u8 *action_type_set,
+			      u32 actions_caps, u8 *last_ste,
+			      struct mlx5dr_ste_actions_attr *attr, u32 *added_stes);
+void dr_ste_v1_set_action_set(u8 *d_action, u8 hw_field, u8 shifter,
+			      u8 length, u32 data);
+void dr_ste_v1_set_action_add(u8 *d_action, u8 hw_field, u8 shifter,
+			      u8 length, u32 data);
+void dr_ste_v1_set_action_copy(u8 *d_action, u8 dst_hw_field, u8 dst_shifter,
+			       u8 dst_len, u8 src_hw_field, u8 src_shifter);
+int dr_ste_v1_set_action_decap_l3_list(void *data, u32 data_sz, u8 *hw_action,
+				       u32 hw_action_sz, u16 *used_hw_action_num);
+void dr_ste_v1_build_eth_l2_src_dst_init(struct mlx5dr_ste_build *sb,
+					 struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l3_ipv6_dst_init(struct mlx5dr_ste_build *sb,
+					  struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l3_ipv6_src_init(struct mlx5dr_ste_build *sb,
+					  struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l3_ipv4_5_tuple_init(struct mlx5dr_ste_build *sb,
+					      struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l2_src_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l2_dst_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l2_tnl_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l3_ipv4_misc_init(struct mlx5dr_ste_build *sb,
+					   struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_ipv6_l3_l4_init(struct mlx5dr_ste_build *sb,
+					 struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_mpls_init(struct mlx5dr_ste_build *sb,
+			       struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_gre_init(struct mlx5dr_ste_build *sb,
+				  struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_mpls_init(struct mlx5dr_ste_build *sb,
+				   struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_mpls_over_udp_init(struct mlx5dr_ste_build *sb,
+					    struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_mpls_over_gre_init(struct mlx5dr_ste_build *sb,
+					    struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_icmp_init(struct mlx5dr_ste_build *sb,
+			       struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_general_purpose_init(struct mlx5dr_ste_build *sb,
+					  struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_eth_l4_misc_init(struct mlx5dr_ste_build *sb,
+				      struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_tnl_vxlan_gpe_init(struct mlx5dr_ste_build *sb,
+						    struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_tnl_geneve_init(struct mlx5dr_ste_build *sb,
+						 struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_header_0_1_init(struct mlx5dr_ste_build *sb,
+					 struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_register_0_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_register_1_init(struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_src_gvmi_qpn_init(struct mlx5dr_ste_build *sb,
+				       struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_0_init(struct mlx5dr_ste_build *sb,
+					struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_1_init(struct mlx5dr_ste_build *sb,
+					struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_init(struct mlx5dr_ste_build *sb,
+							 struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_init(struct mlx5dr_ste_build *sb,
+							       struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_flex_parser_tnl_gtpu_init(struct mlx5dr_ste_build *sb,
+					       struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_gtpu_flex_parser_0_init(struct mlx5dr_ste_build *sb,
+						 struct mlx5dr_match_param *mask);
+void dr_ste_v1_build_tnl_gtpu_flex_parser_1_init(struct mlx5dr_ste_build *sb,
+						 struct mlx5dr_match_param *mask);
+
+#endif  /* _DR_STE_V1_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v2.c
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB
+/* Copyright (c) 2022, NVIDIA CORPORATION & AFFILIATES. All rights reserved. */
+
+#include "dr_ste_v1.h"
+
+enum {
+	DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_0		= 0x00,
+	DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_1		= 0x01,
+	DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_2		= 0x02,
+	DR_STE_V2_ACTION_MDFY_FLD_SRC_L2_OUT_0		= 0x08,
+	DR_STE_V2_ACTION_MDFY_FLD_SRC_L2_OUT_1		= 0x09,
+	DR_STE_V2_ACTION_MDFY_FLD_L3_OUT_0		= 0x0e,
+	DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_0		= 0x18,
+	DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_1		= 0x19,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV4_OUT_0		= 0x40,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV4_OUT_1		= 0x41,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_0	= 0x44,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_1	= 0x45,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_2	= 0x46,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_3	= 0x47,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_0	= 0x4c,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_1	= 0x4d,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_2	= 0x4e,
+	DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_3	= 0x4f,
+	DR_STE_V2_ACTION_MDFY_FLD_TCP_MISC_0		= 0x5e,
+	DR_STE_V2_ACTION_MDFY_FLD_TCP_MISC_1		= 0x5f,
+	DR_STE_V2_ACTION_MDFY_FLD_CFG_HDR_0_0		= 0x6f,
+	DR_STE_V2_ACTION_MDFY_FLD_CFG_HDR_0_1		= 0x70,
+	DR_STE_V2_ACTION_MDFY_FLD_METADATA_2_CQE	= 0x7b,
+	DR_STE_V2_ACTION_MDFY_FLD_GNRL_PURPOSE		= 0x7c,
+	DR_STE_V2_ACTION_MDFY_FLD_REGISTER_2_0		= 0x90,
+	DR_STE_V2_ACTION_MDFY_FLD_REGISTER_2_1		= 0x91,
+	DR_STE_V2_ACTION_MDFY_FLD_REGISTER_1_0		= 0x92,
+	DR_STE_V2_ACTION_MDFY_FLD_REGISTER_1_1		= 0x93,
+	DR_STE_V2_ACTION_MDFY_FLD_REGISTER_0_0		= 0x94,
+	DR_STE_V2_ACTION_MDFY_FLD_REGISTER_0_1		= 0x95,
+};
+
+static const struct mlx5dr_ste_action_modify_field dr_ste_v2_action_modify_field_arr[] = {
+	[MLX5_ACTION_IN_FIELD_OUT_SMAC_47_16] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_SRC_L2_OUT_0, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_SMAC_15_0] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_SRC_L2_OUT_1, .start = 16, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_ETHERTYPE] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_1, .start = 0, .end = 15,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DMAC_47_16] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_0, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DMAC_15_0] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_1, .start = 16, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_IP_DSCP] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L3_OUT_0, .start = 18, .end = 23,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_TCP_FLAGS] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_1, .start = 16, .end = 24,
+		.l4_type = DR_STE_ACTION_MDFY_TYPE_L4_TCP,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_TCP_SPORT] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_0, .start = 16, .end = 31,
+		.l4_type = DR_STE_ACTION_MDFY_TYPE_L4_TCP,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_TCP_DPORT] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_0, .start = 0, .end = 15,
+		.l4_type = DR_STE_ACTION_MDFY_TYPE_L4_TCP,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_IP_TTL] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L3_OUT_0, .start = 8, .end = 15,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV4,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_IPV6_HOPLIMIT] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L3_OUT_0, .start = 8, .end = 15,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_UDP_SPORT] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_0, .start = 16, .end = 31,
+		.l4_type = DR_STE_ACTION_MDFY_TYPE_L4_UDP,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_UDP_DPORT] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L4_OUT_0, .start = 0, .end = 15,
+		.l4_type = DR_STE_ACTION_MDFY_TYPE_L4_UDP,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_SIPV6_127_96] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_0, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_SIPV6_95_64] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_1, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_SIPV6_63_32] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_2, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_SIPV6_31_0] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_SRC_OUT_3, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DIPV6_127_96] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_0, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DIPV6_95_64] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_1, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DIPV6_63_32] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_2, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DIPV6_31_0] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV6_DST_OUT_3, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV6,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_SIPV4] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV4_OUT_0, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV4,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_DIPV4] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_IPV4_OUT_1, .start = 0, .end = 31,
+		.l3_type = DR_STE_ACTION_MDFY_TYPE_L3_IPV4,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_A] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_GNRL_PURPOSE, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_B] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_METADATA_2_CQE, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_0] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_REGISTER_0_0, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_1] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_REGISTER_0_1, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_2] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_REGISTER_1_0, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_3] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_REGISTER_1_1, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_4] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_REGISTER_2_0, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_METADATA_REG_C_5] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_REGISTER_2_1, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_TCP_SEQ_NUM] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_TCP_MISC_0, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_TCP_ACK_NUM] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_TCP_MISC_1, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_FIRST_VID] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_L2_OUT_2, .start = 0, .end = 15,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_EMD_31_0] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_CFG_HDR_0_1, .start = 0, .end = 31,
+	},
+	[MLX5_ACTION_IN_FIELD_OUT_EMD_47_32] = {
+		.hw_field = DR_STE_V2_ACTION_MDFY_FLD_CFG_HDR_0_0, .start = 0, .end = 15,
+	},
+};
+
+static struct mlx5dr_ste_ctx ste_ctx_v2 = {
+	/* Builders */
+	.build_eth_l2_src_dst_init	= &dr_ste_v1_build_eth_l2_src_dst_init,
+	.build_eth_l3_ipv6_src_init	= &dr_ste_v1_build_eth_l3_ipv6_src_init,
+	.build_eth_l3_ipv6_dst_init	= &dr_ste_v1_build_eth_l3_ipv6_dst_init,
+	.build_eth_l3_ipv4_5_tuple_init	= &dr_ste_v1_build_eth_l3_ipv4_5_tuple_init,
+	.build_eth_l2_src_init		= &dr_ste_v1_build_eth_l2_src_init,
+	.build_eth_l2_dst_init		= &dr_ste_v1_build_eth_l2_dst_init,
+	.build_eth_l2_tnl_init		= &dr_ste_v1_build_eth_l2_tnl_init,
+	.build_eth_l3_ipv4_misc_init	= &dr_ste_v1_build_eth_l3_ipv4_misc_init,
+	.build_eth_ipv6_l3_l4_init	= &dr_ste_v1_build_eth_ipv6_l3_l4_init,
+	.build_mpls_init		= &dr_ste_v1_build_mpls_init,
+	.build_tnl_gre_init		= &dr_ste_v1_build_tnl_gre_init,
+	.build_tnl_mpls_init		= &dr_ste_v1_build_tnl_mpls_init,
+	.build_tnl_mpls_over_udp_init	= &dr_ste_v1_build_tnl_mpls_over_udp_init,
+	.build_tnl_mpls_over_gre_init	= &dr_ste_v1_build_tnl_mpls_over_gre_init,
+	.build_icmp_init		= &dr_ste_v1_build_icmp_init,
+	.build_general_purpose_init	= &dr_ste_v1_build_general_purpose_init,
+	.build_eth_l4_misc_init		= &dr_ste_v1_build_eth_l4_misc_init,
+	.build_tnl_vxlan_gpe_init	= &dr_ste_v1_build_flex_parser_tnl_vxlan_gpe_init,
+	.build_tnl_geneve_init		= &dr_ste_v1_build_flex_parser_tnl_geneve_init,
+	.build_tnl_geneve_tlv_opt_init	= &dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_init,
+	.build_tnl_geneve_tlv_opt_exist_init =
+				  &dr_ste_v1_build_flex_parser_tnl_geneve_tlv_opt_exist_init,
+	.build_register_0_init		= &dr_ste_v1_build_register_0_init,
+	.build_register_1_init		= &dr_ste_v1_build_register_1_init,
+	.build_src_gvmi_qpn_init	= &dr_ste_v1_build_src_gvmi_qpn_init,
+	.build_flex_parser_0_init	= &dr_ste_v1_build_flex_parser_0_init,
+	.build_flex_parser_1_init	= &dr_ste_v1_build_flex_parser_1_init,
+	.build_tnl_gtpu_init		= &dr_ste_v1_build_flex_parser_tnl_gtpu_init,
+	.build_tnl_header_0_1_init	= &dr_ste_v1_build_tnl_header_0_1_init,
+	.build_tnl_gtpu_flex_parser_0_init = &dr_ste_v1_build_tnl_gtpu_flex_parser_0_init,
+	.build_tnl_gtpu_flex_parser_1_init = &dr_ste_v1_build_tnl_gtpu_flex_parser_1_init,
+
+	/* Getters and Setters */
+	.ste_init			= &dr_ste_v1_init,
+	.set_next_lu_type		= &dr_ste_v1_set_next_lu_type,
+	.get_next_lu_type		= &dr_ste_v1_get_next_lu_type,
+	.set_miss_addr			= &dr_ste_v1_set_miss_addr,
+	.get_miss_addr			= &dr_ste_v1_get_miss_addr,
+	.set_hit_addr			= &dr_ste_v1_set_hit_addr,
+	.set_byte_mask			= &dr_ste_v1_set_byte_mask,
+	.get_byte_mask			= &dr_ste_v1_get_byte_mask,
+
+	/* Actions */
+	.actions_caps			= DR_STE_CTX_ACTION_CAP_TX_POP |
+					  DR_STE_CTX_ACTION_CAP_RX_PUSH |
+					  DR_STE_CTX_ACTION_CAP_RX_ENCAP,
+	.set_actions_rx			= &dr_ste_v1_set_actions_rx,
+	.set_actions_tx			= &dr_ste_v1_set_actions_tx,
+	.modify_field_arr_sz		= ARRAY_SIZE(dr_ste_v2_action_modify_field_arr),
+	.modify_field_arr		= dr_ste_v2_action_modify_field_arr,
+	.set_action_set			= &dr_ste_v1_set_action_set,
+	.set_action_add			= &dr_ste_v1_set_action_add,
+	.set_action_copy		= &dr_ste_v1_set_action_copy,
+	.set_action_decap_l3_list	= &dr_ste_v1_set_action_decap_l3_list,
+
+	/* Send */
+	.prepare_for_postsend		= &dr_ste_v1_prepare_for_postsend,
+};
+
+struct mlx5dr_ste_ctx *mlx5dr_ste_get_ctx_v2(void)
+{
+	return &ste_ctx_v2;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_table.c
@@ -3,12 +3,47 @@
 
 #include "dr_types.h"
 
-int mlx5dr_table_set_miss_action(struct mlx5dr_table *tbl,
-				 struct mlx5dr_action *action)
+static int dr_table_set_miss_action_nic(struct mlx5dr_domain *dmn,
+					struct mlx5dr_table_rx_tx *nic_tbl,
+					struct mlx5dr_action *action)
 {
-	struct mlx5dr_matcher *last_matcher = NULL;
+	struct mlx5dr_matcher_rx_tx *last_nic_matcher = NULL;
 	struct mlx5dr_htbl_connect_info info;
 	struct mlx5dr_ste_htbl *last_htbl;
+	int ret = -EOPNOTSUPP;
+
+	if (!list_empty(&nic_tbl->nic_matcher_list))
+		last_nic_matcher = list_last_entry(&nic_tbl->nic_matcher_list,
+						   struct mlx5dr_matcher_rx_tx,
+						   list_node);
+
+	if (last_nic_matcher)
+		last_htbl = last_nic_matcher->e_anchor;
+	else
+		last_htbl = nic_tbl->s_anchor;
+
+	if (action)
+		nic_tbl->default_icm_addr =
+			nic_tbl->nic_dmn->type == DR_DOMAIN_NIC_TYPE_RX ?
+				action->dest_tbl->tbl->rx.s_anchor->chunk->icm_addr :
+				action->dest_tbl->tbl->tx.s_anchor->chunk->icm_addr;
+	else
+		nic_tbl->default_icm_addr = nic_tbl->nic_dmn->default_icm_addr;
+
+	info.type = CONNECT_MISS;
+	info.miss_icm_addr = nic_tbl->default_icm_addr;
+
+	ret = mlx5dr_ste_htbl_init_and_postsend(dmn, nic_tbl->nic_dmn,
+						last_htbl, &info, true);
+	if (ret)
+		mlx5dr_dbg(dmn, "Failed to set NIC RX/TX miss action, ret %d\n", ret);
+
+	return ret;
+}
+
+int mlx5dr_table_set_miss_action(struct mlx5dr_table *tbl,
+				 struct mlx5dr_action *action)
+{
 	int ret;
 
 	if (action && action->action_type != DR_ACTION_TYP_FT)
@@ -16,58 +51,23 @@
 
 	mlx5dr_domain_lock(tbl->dmn);
 
-	if (!list_empty(&tbl->matcher_list))
-		last_matcher = list_last_entry(&tbl->matcher_list,
-					       struct mlx5dr_matcher,
-					       matcher_list);
-
 	if (tbl->dmn->type == MLX5DR_DOMAIN_TYPE_NIC_RX ||
 	    tbl->dmn->type == MLX5DR_DOMAIN_TYPE_FDB) {
-		if (last_matcher)
-			last_htbl = last_matcher->rx.e_anchor;
-		else
-			last_htbl = tbl->rx.s_anchor;
-
-		tbl->rx.default_icm_addr = action ?
-			action->dest_tbl->tbl->rx.s_anchor->chunk->icm_addr :
-			tbl->rx.nic_dmn->default_icm_addr;
-
-		info.type = CONNECT_MISS;
-		info.miss_icm_addr = tbl->rx.default_icm_addr;
-
-		ret = mlx5dr_ste_htbl_init_and_postsend(tbl->dmn,
-							tbl->rx.nic_dmn,
-							last_htbl,
-							&info, true);
-		if (ret) {
-			mlx5dr_dbg(tbl->dmn, "Failed to set RX miss action, ret %d\n", ret);
+		ret = dr_table_set_miss_action_nic(tbl->dmn, &tbl->rx, action);
+		if (ret)
 			goto out;
-		}
 	}
 
 	if (tbl->dmn->type == MLX5DR_DOMAIN_TYPE_NIC_TX ||
 	    tbl->dmn->type == MLX5DR_DOMAIN_TYPE_FDB) {
-		if (last_matcher)
-			last_htbl = last_matcher->tx.e_anchor;
-		else
-			last_htbl = tbl->tx.s_anchor;
-
-		tbl->tx.default_icm_addr = action ?
-			action->dest_tbl->tbl->tx.s_anchor->chunk->icm_addr :
-			tbl->tx.nic_dmn->default_icm_addr;
-
-		info.type = CONNECT_MISS;
-		info.miss_icm_addr = tbl->tx.default_icm_addr;
-
-		ret = mlx5dr_ste_htbl_init_and_postsend(tbl->dmn,
-							tbl->tx.nic_dmn,
-							last_htbl, &info, true);
-		if (ret) {
-			mlx5dr_dbg(tbl->dmn, "Failed to set TX miss action, ret %d\n", ret);
+		ret = dr_table_set_miss_action_nic(tbl->dmn, &tbl->tx, action);
+		if (ret)
 			goto out;
-		}
 	}
 
+	if (ret)
+		goto out;
+
 	/* Release old action */
 	if (tbl->miss_action)
 		refcount_dec(&tbl->miss_action->refcount);
@@ -122,6 +122,8 @@
 	struct mlx5dr_htbl_connect_info info;
 	int ret;
 
+	INIT_LIST_HEAD(&nic_tbl->nic_matcher_list);
+
 	nic_tbl->default_icm_addr = nic_dmn->default_icm_addr;
 
 	nic_tbl->s_anchor = mlx5dr_ste_htbl_alloc(dmn->ste_icm_pool,
@@ -266,6 +268,8 @@
 	if (ret)
 		goto uninit_tbl;
 
+	INIT_LIST_HEAD(&tbl->dbg_node);
+	mlx5dr_dbg_tbl_add(tbl);
 	return tbl;
 
 uninit_tbl:
@@ -281,9 +285,10 @@
 {
 	int ret;
 
-	if (refcount_read(&tbl->refcount) > 1)
+	if (WARN_ON_ONCE(refcount_read(&tbl->refcount) > 1))
 		return -EBUSY;
 
+	mlx5dr_dbg_tbl_del(tbl);
 	ret = dr_table_destroy_sw_owned_tbl(tbl);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_types.h
@@ -4,17 +4,17 @@
 #ifndef	_DR_TYPES_
 #define	_DR_TYPES_
 
-#include <linux/mlx5/driver.h>
+#include <linux/mlx5/vport.h>
 #include <linux/refcount.h>
 #include "fs_core.h"
 #include "wq.h"
 #include "lib/mlx5.h"
 #include "mlx5_ifc_dr.h"
 #include "mlx5dr.h"
+#include "dr_dbg.h"
 
 #define DR_RULE_MAX_STES 18
 #define DR_ACTION_MAX_STES 5
-#define WIRE_PORT 0xFFFF
 #define DR_STE_SVLAN 0x1
 #define DR_STE_CVLAN 0x2
 #define DR_SZ_MATCH_PARAM (MLX5_ST_SZ_DW_MATCH_PARAM * 4)
@@ -91,6 +91,7 @@
 	DR_STE_CTX_ACTION_CAP_TX_POP   = 1 << 0,
 	DR_STE_CTX_ACTION_CAP_RX_PUSH  = 1 << 1,
 	DR_STE_CTX_ACTION_CAP_RX_ENCAP = 1 << 2,
+	DR_STE_CTX_ACTION_CAP_POP_MDFY = 1 << 3,
 };
 
 enum {
@@ -105,7 +106,8 @@
 	DR_MATCHER_CRITERIA_MISC2 = 1 << 3,
 	DR_MATCHER_CRITERIA_MISC3 = 1 << 4,
 	DR_MATCHER_CRITERIA_MISC4 = 1 << 5,
-	DR_MATCHER_CRITERIA_MAX = 1 << 6,
+	DR_MATCHER_CRITERIA_MISC5 = 1 << 6,
+	DR_MATCHER_CRITERIA_MAX = 1 << 7,
 };
 
 enum mlx5dr_action_type {
@@ -441,6 +443,11 @@
 					 struct mlx5dr_match_param *mask,
 					 struct mlx5dr_cmd_caps *caps,
 					 bool inner, bool rx);
+void mlx5dr_ste_build_tnl_geneve_tlv_opt_exist(struct mlx5dr_ste_ctx *ste_ctx,
+					       struct mlx5dr_ste_build *sb,
+					       struct mlx5dr_match_param *mask,
+					       struct mlx5dr_cmd_caps *caps,
+					       bool inner, bool rx);
 void mlx5dr_ste_build_tnl_gtpu(struct mlx5dr_ste_ctx *ste_ctx,
 			       struct mlx5dr_ste_build *sb,
 			       struct mlx5dr_match_param *mask,
@@ -455,6 +462,10 @@
 					     struct mlx5dr_match_param *mask,
 					     struct mlx5dr_cmd_caps *caps,
 					     bool inner, bool rx);
+void mlx5dr_ste_build_tnl_header_0_1(struct mlx5dr_ste_ctx *ste_ctx,
+				     struct mlx5dr_ste_build *sb,
+				     struct mlx5dr_match_param *mask,
+				     bool inner, bool rx);
 void mlx5dr_ste_build_general_purpose(struct mlx5dr_ste_ctx *ste_ctx,
 				      struct mlx5dr_ste_build *sb,
 				      struct mlx5dr_match_param *mask,
@@ -495,57 +506,66 @@
 	/* Incoming packet Ethertype - this is the Ethertype
 	 * following the last VLAN tag of the packet
 	 */
-	u32 ethertype:16;
 	u32 smac_15_0:16;	/* Source MAC address of incoming packet */
+	u32 ethertype:16;
+
 	u32 dmac_47_16;		/* Destination MAC address of incoming packet */
-	/* VLAN ID of first VLAN tag in the incoming packet.
+
+	u32 dmac_15_0:16;	/* Destination MAC address of incoming packet */
+	/* Priority of first VLAN tag in the incoming packet.
 	 * Valid only when cvlan_tag==1 or svlan_tag==1
 	 */
-	u32 first_vid:12;
+	u32 first_prio:3;
 	/* CFI bit of first VLAN tag in the incoming packet.
 	 * Valid only when cvlan_tag==1 or svlan_tag==1
 	 */
 	u32 first_cfi:1;
-	/* Priority of first VLAN tag in the incoming packet.
+	/* VLAN ID of first VLAN tag in the incoming packet.
 	 * Valid only when cvlan_tag==1 or svlan_tag==1
 	 */
-	u32 first_prio:3;
-	u32 dmac_15_0:16;	/* Destination MAC address of incoming packet */
-	/* TCP flags. ;Bit 0: FIN;Bit 1: SYN;Bit 2: RST;Bit 3: PSH;Bit 4: ACK;
-	 *             Bit 5: URG;Bit 6: ECE;Bit 7: CWR;Bit 8: NS
+	u32 first_vid:12;
+
+	u32 ip_protocol:8;	/* IP protocol */
+	/* Differentiated Services Code Point derived from
+	 * Traffic Class/TOS field of IPv6/v4
 	 */
-	u32 tcp_flags:9;
-	u32 ip_version:4;	/* IP version */
-	u32 frag:1;		/* Packet is an IP fragment */
-	/* The first vlan in the packet is s-vlan (0x8a88).
-	 * cvlan_tag and svlan_tag cannot be set together
+	u32 ip_dscp:6;
+	/* Explicit Congestion Notification derived from
+	 * Traffic Class/TOS field of IPv6/v4
 	 */
-	u32 svlan_tag:1;
+	u32 ip_ecn:2;
 	/* The first vlan in the packet is c-vlan (0x8100).
 	 * cvlan_tag and svlan_tag cannot be set together
 	 */
 	u32 cvlan_tag:1;
-	/* Explicit Congestion Notification derived from
-	 * Traffic Class/TOS field of IPv6/v4
+	/* The first vlan in the packet is s-vlan (0x8a88).
+	 * cvlan_tag and svlan_tag cannot be set together
 	 */
-	u32 ip_ecn:2;
-	/* Differentiated Services Code Point derived from
-	 * Traffic Class/TOS field of IPv6/v4
+	u32 svlan_tag:1;
+	u32 frag:1;		/* Packet is an IP fragment */
+	u32 ip_version:4;	/* IP version */
+	/* TCP flags. ;Bit 0: FIN;Bit 1: SYN;Bit 2: RST;Bit 3: PSH;Bit 4: ACK;
+	 *             Bit 5: URG;Bit 6: ECE;Bit 7: CWR;Bit 8: NS
 	 */
-	u32 ip_dscp:6;
-	u32 ip_protocol:8;	/* IP protocol */
+	u32 tcp_flags:9;
+
+	/* TCP source port.;tcp and udp sport/dport are mutually exclusive */
+	u32 tcp_sport:16;
 	/* TCP destination port.
 	 * tcp and udp sport/dport are mutually exclusive
 	 */
 	u32 tcp_dport:16;
-	/* TCP source port.;tcp and udp sport/dport are mutually exclusive */
-	u32 tcp_sport:16;
+
+	u32 reserved_auto1:16;
+	u32 ipv4_ihl:4;
+	u32 reserved_auto2:4;
 	u32 ttl_hoplimit:8;
-	u32 reserved:24;
-	/* UDP destination port.;tcp and udp sport/dport are mutually exclusive */
-	u32 udp_dport:16;
+
 	/* UDP source port.;tcp and udp sport/dport are mutually exclusive */
 	u32 udp_sport:16;
+	/* UDP destination port.;tcp and udp sport/dport are mutually exclusive */
+	u32 udp_dport:16;
+
 	/* IPv6 source address of incoming packets
 	 * For IPv4 address use bits 31:0 (rest of the bits are reserved)
 	 * This field should be qualified by an appropriate ethertype
@@ -589,96 +609,114 @@
 };
 
 struct mlx5dr_match_misc {
-	u32 source_sqn:24;		/* Source SQN */
-	u32 source_vhca_port:4;
-	/* used with GRE, sequence number exist when gre_s_present == 1 */
-	u32 gre_s_present:1;
-	/* used with GRE, key exist when gre_k_present == 1 */
-	u32 gre_k_present:1;
-	u32 reserved_auto1:1;
 	/* used with GRE, checksum exist when gre_c_present == 1 */
 	u32 gre_c_present:1;
+	u32 reserved_auto1:1;
+	/* used with GRE, key exist when gre_k_present == 1 */
+	u32 gre_k_present:1;
+	/* used with GRE, sequence number exist when gre_s_present == 1 */
+	u32 gre_s_present:1;
+	u32 source_vhca_port:4;
+	u32 source_sqn:24;		/* Source SQN */
+
+	u32 source_eswitch_owner_vhca_id:16;
 	/* Source port.;0xffff determines wire port */
 	u32 source_port:16;
-	u32 source_eswitch_owner_vhca_id:16;
-	/* VLAN ID of first VLAN tag the inner header of the incoming packet.
-	 * Valid only when inner_second_cvlan_tag ==1 or inner_second_svlan_tag ==1
-	 */
-	u32 inner_second_vid:12;
-	/* CFI bit of first VLAN tag in the inner header of the incoming packet.
-	 * Valid only when inner_second_cvlan_tag ==1 or inner_second_svlan_tag ==1
-	 */
-	u32 inner_second_cfi:1;
-	/* Priority of second VLAN tag in the inner header of the incoming packet.
-	 * Valid only when inner_second_cvlan_tag ==1 or inner_second_svlan_tag ==1
-	 */
-	u32 inner_second_prio:3;
-	/* VLAN ID of first VLAN tag the outer header of the incoming packet.
+
+	/* Priority of second VLAN tag in the outer header of the incoming packet.
 	 * Valid only when outer_second_cvlan_tag ==1 or outer_second_svlan_tag ==1
 	 */
-	u32 outer_second_vid:12;
+	u32 outer_second_prio:3;
 	/* CFI bit of first VLAN tag in the outer header of the incoming packet.
 	 * Valid only when outer_second_cvlan_tag ==1 or outer_second_svlan_tag ==1
 	 */
 	u32 outer_second_cfi:1;
-	/* Priority of second VLAN tag in the outer header of the incoming packet.
+	/* VLAN ID of first VLAN tag the outer header of the incoming packet.
 	 * Valid only when outer_second_cvlan_tag ==1 or outer_second_svlan_tag ==1
 	 */
-	u32 outer_second_prio:3;
-	u32 gre_protocol:16;		/* GRE Protocol (outer) */
-	u32 reserved_auto3:12;
-	/* The second vlan in the inner header of the packet is s-vlan (0x8a88).
-	 * inner_second_cvlan_tag and inner_second_svlan_tag cannot be set together
+	u32 outer_second_vid:12;
+	/* Priority of second VLAN tag in the inner header of the incoming packet.
+	 * Valid only when inner_second_cvlan_tag ==1 or inner_second_svlan_tag ==1
 	 */
-	u32 inner_second_svlan_tag:1;
-	/* The second vlan in the outer header of the packet is s-vlan (0x8a88).
+	u32 inner_second_prio:3;
+	/* CFI bit of first VLAN tag in the inner header of the incoming packet.
+	 * Valid only when inner_second_cvlan_tag ==1 or inner_second_svlan_tag ==1
+	 */
+	u32 inner_second_cfi:1;
+	/* VLAN ID of first VLAN tag the inner header of the incoming packet.
+	 * Valid only when inner_second_cvlan_tag ==1 or inner_second_svlan_tag ==1
+	 */
+	u32 inner_second_vid:12;
+
+	u32 outer_second_cvlan_tag:1;
+	u32 inner_second_cvlan_tag:1;
+	/* The second vlan in the outer header of the packet is c-vlan (0x8100).
 	 * outer_second_cvlan_tag and outer_second_svlan_tag cannot be set together
 	 */
 	u32 outer_second_svlan_tag:1;
 	/* The second vlan in the inner header of the packet is c-vlan (0x8100).
 	 * inner_second_cvlan_tag and inner_second_svlan_tag cannot be set together
 	 */
-	u32 inner_second_cvlan_tag:1;
-	/* The second vlan in the outer header of the packet is c-vlan (0x8100).
+	u32 inner_second_svlan_tag:1;
+	/* The second vlan in the outer header of the packet is s-vlan (0x8a88).
 	 * outer_second_cvlan_tag and outer_second_svlan_tag cannot be set together
 	 */
-	u32 outer_second_cvlan_tag:1;
-	u32 gre_key_l:8;		/* GRE Key [7:0] (outer) */
+	u32 reserved_auto2:12;
+	/* The second vlan in the inner header of the packet is s-vlan (0x8a88).
+	 * inner_second_cvlan_tag and inner_second_svlan_tag cannot be set together
+	 */
+	u32 gre_protocol:16;		/* GRE Protocol (outer) */
+
 	u32 gre_key_h:24;		/* GRE Key[31:8] (outer) */
-	u32 reserved_auto4:8;
+	u32 gre_key_l:8;		/* GRE Key [7:0] (outer) */
+
 	u32 vxlan_vni:24;		/* VXLAN VNI (outer) */
-	u32 geneve_oam:1;		/* GENEVE OAM field (outer) */
-	u32 reserved_auto5:7;
+	u32 reserved_auto3:8;
+
 	u32 geneve_vni:24;		/* GENEVE VNI field (outer) */
+	u32 reserved_auto4:6;
+	u32 geneve_tlv_option_0_exist:1;
+	u32 geneve_oam:1;		/* GENEVE OAM field (outer) */
+
+	u32 reserved_auto5:12;
 	u32 outer_ipv6_flow_label:20;	/* Flow label of incoming IPv6 packet (outer) */
+
 	u32 reserved_auto6:12;
 	u32 inner_ipv6_flow_label:20;	/* Flow label of incoming IPv6 packet (inner) */
-	u32 reserved_auto7:12;
-	u32 geneve_protocol_type:16;	/* GENEVE protocol type (outer) */
+
+	u32 reserved_auto7:10;
 	u32 geneve_opt_len:6;		/* GENEVE OptLen (outer) */
-	u32 reserved_auto8:10;
+	u32 geneve_protocol_type:16;	/* GENEVE protocol type (outer) */
+
+	u32 reserved_auto8:8;
 	u32 bth_dst_qp:24;		/* Destination QP in BTH header */
-	u32 reserved_auto9:8;
-	u8 reserved_auto10[20];
+
+	u32 reserved_auto9;
+	u32 outer_esp_spi;
+	u32 reserved_auto10[3];
 };
 
 struct mlx5dr_match_misc2 {
-	u32 outer_first_mpls_ttl:8;		/* First MPLS TTL (outer) */
-	u32 outer_first_mpls_s_bos:1;		/* First MPLS S_BOS (outer) */
-	u32 outer_first_mpls_exp:3;		/* First MPLS EXP (outer) */
 	u32 outer_first_mpls_label:20;		/* First MPLS LABEL (outer) */
-	u32 inner_first_mpls_ttl:8;		/* First MPLS TTL (inner) */
-	u32 inner_first_mpls_s_bos:1;		/* First MPLS S_BOS (inner) */
-	u32 inner_first_mpls_exp:3;		/* First MPLS EXP (inner) */
+	u32 outer_first_mpls_exp:3;		/* First MPLS EXP (outer) */
+	u32 outer_first_mpls_s_bos:1;		/* First MPLS S_BOS (outer) */
+	u32 outer_first_mpls_ttl:8;		/* First MPLS TTL (outer) */
+
 	u32 inner_first_mpls_label:20;		/* First MPLS LABEL (inner) */
-	u32 outer_first_mpls_over_gre_ttl:8;	/* last MPLS TTL (outer) */
-	u32 outer_first_mpls_over_gre_s_bos:1;	/* last MPLS S_BOS (outer) */
-	u32 outer_first_mpls_over_gre_exp:3;	/* last MPLS EXP (outer) */
+	u32 inner_first_mpls_exp:3;		/* First MPLS EXP (inner) */
+	u32 inner_first_mpls_s_bos:1;		/* First MPLS S_BOS (inner) */
+	u32 inner_first_mpls_ttl:8;		/* First MPLS TTL (inner) */
+
 	u32 outer_first_mpls_over_gre_label:20;	/* last MPLS LABEL (outer) */
-	u32 outer_first_mpls_over_udp_ttl:8;	/* last MPLS TTL (outer) */
-	u32 outer_first_mpls_over_udp_s_bos:1;	/* last MPLS S_BOS (outer) */
-	u32 outer_first_mpls_over_udp_exp:3;	/* last MPLS EXP (outer) */
+	u32 outer_first_mpls_over_gre_exp:3;	/* last MPLS EXP (outer) */
+	u32 outer_first_mpls_over_gre_s_bos:1;	/* last MPLS S_BOS (outer) */
+	u32 outer_first_mpls_over_gre_ttl:8;	/* last MPLS TTL (outer) */
+
 	u32 outer_first_mpls_over_udp_label:20;	/* last MPLS LABEL (outer) */
+	u32 outer_first_mpls_over_udp_exp:3;	/* last MPLS EXP (outer) */
+	u32 outer_first_mpls_over_udp_s_bos:1;	/* last MPLS S_BOS (outer) */
+	u32 outer_first_mpls_over_udp_ttl:8;	/* last MPLS TTL (outer) */
+
 	u32 metadata_reg_c_7;			/* metadata_reg_c_7 */
 	u32 metadata_reg_c_6;			/* metadata_reg_c_6 */
 	u32 metadata_reg_c_5;			/* metadata_reg_c_5 */
@@ -688,7 +726,7 @@
 	u32 metadata_reg_c_1;			/* metadata_reg_c_1 */
 	u32 metadata_reg_c_0;			/* metadata_reg_c_0 */
 	u32 metadata_reg_a;			/* metadata_reg_a */
-	u8 reserved_auto2[12];
+	u32 reserved_auto1[3];
 };
 
 struct mlx5dr_match_misc3 {
@@ -696,24 +734,34 @@
 	u32 outer_tcp_seq_num;
 	u32 inner_tcp_ack_num;
 	u32 outer_tcp_ack_num;
-	u32 outer_vxlan_gpe_vni:24;
+
 	u32 reserved_auto1:8;
-	u32 reserved_auto2:16;
-	u32 outer_vxlan_gpe_flags:8;
+	u32 outer_vxlan_gpe_vni:24;
+
 	u32 outer_vxlan_gpe_next_protocol:8;
+	u32 outer_vxlan_gpe_flags:8;
+	u32 reserved_auto2:16;
+
 	u32 icmpv4_header_data;
 	u32 icmpv6_header_data;
-	u8 icmpv6_code;
-	u8 icmpv6_type;
-	u8 icmpv4_code;
+
 	u8 icmpv4_type;
+	u8 icmpv4_code;
+	u8 icmpv6_type;
+	u8 icmpv6_code;
+
 	u32 geneve_tlv_option_0_data;
-	u8 gtpu_msg_flags;
-	u8 gtpu_msg_type;
+
 	u32 gtpu_teid;
+
+	u8 gtpu_msg_type;
+	u8 gtpu_msg_flags;
+	u32 reserved_auto3:16;
+
 	u32 gtpu_dw_2;
 	u32 gtpu_first_ext_dw_0;
 	u32 gtpu_dw_0;
+	u32 reserved_auto4;
 };
 
 struct mlx5dr_match_misc4 {
@@ -725,6 +773,18 @@
 	u32 prog_sample_field_id_2;
 	u32 prog_sample_field_value_3;
 	u32 prog_sample_field_id_3;
+	u32 reserved_auto1[8];
+};
+
+struct mlx5dr_match_misc5 {
+	u32 macsec_tag_0;
+	u32 macsec_tag_1;
+	u32 macsec_tag_2;
+	u32 macsec_tag_3;
+	u32 tunnel_header_0;
+	u32 tunnel_header_1;
+	u32 tunnel_header_2;
+	u32 tunnel_header_3;
 };
 
 struct mlx5dr_match_param {
@@ -734,12 +794,23 @@
 	struct mlx5dr_match_misc2 misc2;
 	struct mlx5dr_match_misc3 misc3;
 	struct mlx5dr_match_misc4 misc4;
+	struct mlx5dr_match_misc5 misc5;
 };
 
 #define DR_MASK_IS_ICMPV4_SET(_misc3) ((_misc3)->icmpv4_type || \
 				       (_misc3)->icmpv4_code || \
 				       (_misc3)->icmpv4_header_data)
 
+#define DR_MASK_IS_SRC_IP_SET(_spec) ((_spec)->src_ip_127_96 || \
+				      (_spec)->src_ip_95_64  || \
+				      (_spec)->src_ip_63_32  || \
+				      (_spec)->src_ip_31_0)
+
+#define DR_MASK_IS_DST_IP_SET(_spec) ((_spec)->dst_ip_127_96 || \
+				      (_spec)->dst_ip_95_64  || \
+				      (_spec)->dst_ip_63_32  || \
+				      (_spec)->dst_ip_31_0)
+
 struct mlx5dr_esw_caps {
 	u64 drop_icm_address_rx;
 	u64 drop_icm_address_tx;
@@ -752,9 +823,9 @@
 struct mlx5dr_cmd_vport_cap {
 	u16 vport_gvmi;
 	u16 vhca_gvmi;
+	u16 num;
 	u64 icm_address_rx;
 	u64 icm_address_tx;
-	u32 num;
 };
 
 struct mlx5dr_roce_cap {
@@ -763,6 +834,12 @@
 	u8 fl_rc_qp_when_roce_enabled:1;
 };
 
+struct mlx5dr_vports {
+	struct mlx5dr_cmd_vport_cap esw_manager_caps;
+	struct mlx5dr_cmd_vport_cap uplink_caps;
+	struct xarray vports_caps_xa;
+};
+
 struct mlx5dr_cmd_caps {
 	u16 gvmi;
 	u64 nic_rx_drop_address;
@@ -784,9 +861,9 @@
 	u8 flex_parser_id_gtpu_teid;
 	u8 flex_parser_id_gtpu_dw_2;
 	u8 flex_parser_id_gtpu_first_ext_dw_0;
+	u8 flex_parser_ok_bits_supp;
 	u8 max_ft_level;
 	u16 roce_min_src_udp;
-	u8 num_esw_ports;
 	u8 sw_format_ver;
 	bool eswitch_manager;
 	bool rx_sw_owner;
@@ -795,11 +872,11 @@
 	u8 rx_sw_owner_v2:1;
 	u8 tx_sw_owner_v2:1;
 	u8 fdb_sw_owner_v2:1;
-	u32 num_vports;
 	struct mlx5dr_esw_caps esw_caps;
-	struct mlx5dr_cmd_vport_cap *vports_caps;
+	struct mlx5dr_vports vports;
 	bool prio_tag_required;
 	struct mlx5dr_roce_cap roce_caps;
+	u8 is_ecpf:1;
 	u8 isolate_vl_tc:1;
 };
 
@@ -826,10 +903,6 @@
 	struct mlx5dr_cmd_caps caps;
 };
 
-struct mlx5dr_domain_cache {
-	struct mlx5dr_fw_recalc_cs_ft **recalc_cs_ft;
-};
-
 struct mlx5dr_domain {
 	struct mlx5dr_domain *peer_dmn;
 	struct mlx5_core_dev *mdev;
@@ -841,14 +914,17 @@
 	struct mlx5dr_icm_pool *action_icm_pool;
 	struct mlx5dr_send_ring *send_ring;
 	struct mlx5dr_domain_info info;
-	struct mlx5dr_domain_cache cache;
+	struct xarray csum_fts_xa;
 	struct mlx5dr_ste_ctx *ste_ctx;
+	struct list_head dbg_tbl_list;
+	struct mlx5dr_dbg_dump_info dump_info;
 };
 
 struct mlx5dr_table_rx_tx {
 	struct mlx5dr_ste_htbl *s_anchor;
 	struct mlx5dr_domain_rx_tx *nic_dmn;
 	u64 default_icm_addr;
+	struct list_head nic_matcher_list;
 };
 
 struct mlx5dr_table {
@@ -862,6 +938,7 @@
 	struct list_head matcher_list;
 	struct mlx5dr_action *miss_action;
 	refcount_t refcount;
+	struct list_head dbg_node;
 };
 
 struct mlx5dr_matcher_rx_tx {
@@ -875,18 +952,21 @@
 	u8 num_of_builders_arr[DR_RULE_IPV_MAX][DR_RULE_IPV_MAX];
 	u64 default_icm_addr;
 	struct mlx5dr_table_rx_tx *nic_tbl;
+	u32 prio;
+	struct list_head list_node;
+	u32 rules;
 };
 
 struct mlx5dr_matcher {
 	struct mlx5dr_table *tbl;
 	struct mlx5dr_matcher_rx_tx rx;
 	struct mlx5dr_matcher_rx_tx tx;
-	struct list_head matcher_list;
+	struct list_head list_node; /* Used for both matchers and dbg managing */
 	u32 prio;
 	struct mlx5dr_match_param mask;
 	u8 match_criteria;
 	refcount_t refcount;
-	struct mlx5dv_flow_matcher *dv_matcher;
+	struct list_head dbg_rule_list;
 };
 
 struct mlx5dr_ste_action_modify_field {
@@ -942,7 +1022,7 @@
 
 struct mlx5dr_action_ctr {
 	u32 ctr_id;
-	u32 offeset;
+	u32 offset;
 };
 
 struct mlx5dr_action_vport {
@@ -958,6 +1038,11 @@
 	u32 flow_tag;
 };
 
+struct mlx5dr_rule_action_member {
+	struct mlx5dr_action *action;
+	struct list_head list;
+};
+
 struct mlx5dr_action {
 	enum mlx5dr_action_type action_type;
 	refcount_t refcount;
@@ -998,6 +1083,7 @@
 	struct mlx5dr_rule_rx_tx rx;
 	struct mlx5dr_rule_rx_tx tx;
 	struct list_head rule_actions_list;
+	struct list_head dbg_node;
 	u32 flow_source;
 };
 
@@ -1050,6 +1136,11 @@
 	mlx5dr_domain_nic_unlock(&dmn->info.rx);
 }
 
+int mlx5dr_matcher_add_to_tbl_nic(struct mlx5dr_domain *dmn,
+				  struct mlx5dr_matcher_rx_tx *nic_matcher);
+int mlx5dr_matcher_remove_from_tbl_nic(struct mlx5dr_domain *dmn,
+				       struct mlx5dr_matcher_rx_tx *nic_matcher);
+
 int mlx5dr_matcher_select_builders(struct mlx5dr_matcher *matcher,
 				   struct mlx5dr_matcher_rx_tx *nic_matcher,
 				   enum mlx5dr_ipv outer_ipv,
@@ -1102,18 +1193,8 @@
 	return true;
 }
 
-static inline struct mlx5dr_cmd_vport_cap *
-mlx5dr_get_vport_cap(struct mlx5dr_cmd_caps *caps, u32 vport)
-{
-	if (!caps->vports_caps ||
-	    (vport >= caps->num_vports && vport != WIRE_PORT))
-		return NULL;
-
-	if (vport == WIRE_PORT)
-		vport = caps->num_vports;
-
-	return &caps->vports_caps[vport];
-}
+struct mlx5dr_cmd_vport_cap *
+mlx5dr_domain_get_vport_cap(struct mlx5dr_domain *dmn, u16 vport);
 
 struct mlx5dr_cmd_query_flow_table_details {
 	u8 status;
@@ -1154,7 +1235,7 @@
 					u32 table_id,
 					u32 group_id,
 					u32 modify_header_id,
-					u32 vport_id);
+					u16 vport_id);
 int mlx5dr_cmd_del_flow_table_entry(struct mlx5_core_dev *mdev,
 				    u32 table_type,
 				    u32 table_id);
@@ -1241,7 +1322,8 @@
 				  struct mlx5dr_htbl_connect_info *connect_info);
 void mlx5dr_ste_copy_param(u8 match_criteria,
 			   struct mlx5dr_match_param *set_param,
-			   struct mlx5dr_match_parameters *mask);
+			   struct mlx5dr_match_parameters *mask,
+			   bool clear);
 
 struct mlx5dr_qp {
 	struct mlx5_core_dev *mdev;
@@ -1372,19 +1454,20 @@
 };
 
 struct mlx5dr_fw_recalc_cs_ft *
-mlx5dr_fw_create_recalc_cs_ft(struct mlx5dr_domain *dmn, u32 vport_num);
+mlx5dr_fw_create_recalc_cs_ft(struct mlx5dr_domain *dmn, u16 vport_num);
 void mlx5dr_fw_destroy_recalc_cs_ft(struct mlx5dr_domain *dmn,
 				    struct mlx5dr_fw_recalc_cs_ft *recalc_cs_ft);
-int mlx5dr_domain_cache_get_recalc_cs_ft_addr(struct mlx5dr_domain *dmn,
-					      u32 vport_num,
-					      u64 *rx_icm_addr);
+int mlx5dr_domain_get_recalc_cs_ft_addr(struct mlx5dr_domain *dmn,
+					u16 vport_num,
+					u64 *rx_icm_addr);
 int mlx5dr_fw_create_md_tbl(struct mlx5dr_domain *dmn,
 			    struct mlx5dr_cmd_flow_destination_hw_info *dest,
 			    int num_dest,
 			    bool reformat_req,
 			    u32 *tbl_id,
 			    u32 *group_id,
-			    bool ignore_flow_level);
+			    bool ignore_flow_level,
+			    u32 flow_source);
 void mlx5dr_fw_destroy_md_tbl(struct mlx5dr_domain *dmn, u32 tbl_id,
 			      u32 group_id);
 #endif  /* _DR_TYPES_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/fs_dr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/fs_dr.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB
 /* Copyright (c) 2019 Mellanox Technologies */
 
+#include <linux/mlx5/vport.h>
 #include "mlx5_core.h"
 #include "fs_core.h"
 #include "fs_cmd.h"
@@ -43,11 +44,10 @@
 	err = mlx5dr_table_set_miss_action(ft->fs_dr_table.dr_table, action);
 	if (err && action) {
 		err = mlx5dr_action_destroy(action);
-		if (err) {
-			action = NULL;
-			mlx5_core_err(ns->dev, "Failed to destroy action (%d)\n",
-				      err);
-		}
+		if (err)
+			mlx5_core_err(ns->dev,
+				      "Failed to destroy action (%d)\n", err);
+		action = NULL;
 	}
 	ft->fs_dr_table.miss_action = action;
 	if (old_miss_action) {
@@ -194,6 +194,15 @@
 					       dest_attr->vport.vhca_id);
 }
 
+static struct mlx5dr_action *create_uplink_action(struct mlx5dr_domain *domain,
+						  struct mlx5_flow_rule *dst)
+{
+	struct mlx5_flow_destination *dest_attr = &dst->dest_attr;
+
+	return mlx5dr_action_create_dest_vport(domain, MLX5_VPORT_UPLINK, 1,
+					       dest_attr->vport.vhca_id);
+}
+
 static struct mlx5dr_action *create_ft_action(struct mlx5dr_domain *domain,
 					      struct mlx5_flow_rule *dst)
 {
@@ -218,11 +227,16 @@
 
 static bool contain_vport_reformat_action(struct mlx5_flow_rule *dst)
 {
-	return dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_VPORT &&
+	return (dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_VPORT ||
+		dst->dest_attr.type == MLX5_FLOW_DESTINATION_TYPE_UPLINK) &&
 		dst->dest_attr.vport.flags & MLX5_FLOW_DEST_VPORT_REFORMAT_ID;
 }
 
-#define MLX5_FLOW_CONTEXT_ACTION_MAX  20
+/* We want to support a rule with 32 destinations, which means we need to
+ * account for 32 destinations plus usually a counter plus one more action
+ * for a multi-destination flow table.
+ */
+#define MLX5_FLOW_CONTEXT_ACTION_MAX  34
 static int mlx5_cmd_dr_create_fte(struct mlx5_flow_root_namespace *ns,
 				  struct mlx5_flow_table *ft,
 				  struct mlx5_flow_group *group,
@@ -392,9 +406,9 @@
 			enum mlx5_flow_destination_type type = dst->dest_attr.type;
 			u32 id;
 
-			if (num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX ||
-			    num_term_actions >= MLX5_FLOW_CONTEXT_ACTION_MAX) {
-				err = -ENOSPC;
+			if (fs_dr_num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX ||
+			    num_term_actions == MLX5_FLOW_CONTEXT_ACTION_MAX) {
+				err = -EOPNOTSUPP;
 				goto free_actions;
 			}
 
@@ -411,8 +425,11 @@
 				fs_dr_actions[fs_dr_num_actions++] = tmp_action;
 				term_actions[num_term_actions++].dest = tmp_action;
 				break;
+			case MLX5_FLOW_DESTINATION_TYPE_UPLINK:
 			case MLX5_FLOW_DESTINATION_TYPE_VPORT:
-				tmp_action = create_vport_action(domain, dst);
+				tmp_action = type == MLX5_FLOW_DESTINATION_TYPE_VPORT ?
+					     create_vport_action(domain, dst) :
+					     create_uplink_action(domain, dst);
 				if (!tmp_action) {
 					err = -ENOMEM;
 					goto free_actions;
@@ -464,8 +481,9 @@
 			    MLX5_FLOW_DESTINATION_TYPE_COUNTER)
 				continue;
 
-			if (num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX) {
-				err = -ENOSPC;
+			if (num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX ||
+			    fs_dr_num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX) {
+				err = -EOPNOTSUPP;
 				goto free_actions;
 			}
 
@@ -485,18 +503,34 @@
 	params.match_sz = match_sz;
 	params.match_buf = (u64 *)fte->val;
 	if (num_term_actions == 1) {
-		if (term_actions->reformat)
+		if (term_actions->reformat) {
+			if (num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX) {
+				err = -EOPNOTSUPP;
+				goto free_actions;
+			}
 			actions[num_actions++] = term_actions->reformat;
+		}
 
+		if (num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX) {
+			err = -EOPNOTSUPP;
+			goto free_actions;
+		}
 		actions[num_actions++] = term_actions->dest;
 	} else if (num_term_actions > 1) {
 		bool ignore_flow_level =
 			!!(fte->action.flags & FLOW_ACT_IGNORE_FLOW_LEVEL);
+		u32 flow_source = fte->flow_context.flow_source;
 
+		if (num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX ||
+		    fs_dr_num_actions == MLX5_FLOW_CONTEXT_ACTION_MAX) {
+			err = -EOPNOTSUPP;
+			goto free_actions;
+		}
 		tmp_action = mlx5dr_action_create_mult_dest_tbl(domain,
 								term_actions,
 								num_term_actions,
-								ignore_flow_level);
+								ignore_flow_level,
+								flow_source);
 		if (!tmp_action) {
 			err = -EOPNOTSUPP;
 			goto free_actions;
@@ -625,6 +659,19 @@
 	mlx5dr_action_destroy(modify_hdr->action.dr_action);
 }
 
+static int
+mlx5_cmd_dr_destroy_match_definer(struct mlx5_flow_root_namespace *ns,
+				  int definer_id)
+{
+	return -EOPNOTSUPP;
+}
+
+static int mlx5_cmd_dr_create_match_definer(struct mlx5_flow_root_namespace *ns,
+					    u16 format_id, u32 *match_mask)
+{
+	return -EOPNOTSUPP;
+}
+
 static int mlx5_cmd_dr_delete_fte(struct mlx5_flow_root_namespace *ns,
 				  struct mlx5_flow_table *ft,
 				  struct fs_fte *fte)
@@ -708,6 +755,16 @@
 	return mlx5dr_domain_destroy(ns->fs_dr_domain.dr_domain);
 }
 
+static u32 mlx5_cmd_dr_get_capabilities(struct mlx5_flow_root_namespace *ns,
+					enum fs_flow_table_type ft_type)
+{
+	if (ft_type != FS_FT_FDB ||
+	    MLX5_CAP_GEN(ns->dev, steering_format_version) == MLX5_STEERING_FORMAT_CONNECTX_5)
+		return 0;
+
+	return MLX5_FLOW_STEERING_CAP_VLAN_PUSH_ON_RX | MLX5_FLOW_STEERING_CAP_VLAN_POP_ON_TX;
+}
+
 bool mlx5_fs_dr_is_supported(struct mlx5_core_dev *dev)
 {
 	return mlx5dr_is_supported(dev);
@@ -727,9 +784,12 @@
 	.packet_reformat_dealloc = mlx5_cmd_dr_packet_reformat_dealloc,
 	.modify_header_alloc = mlx5_cmd_dr_modify_header_alloc,
 	.modify_header_dealloc = mlx5_cmd_dr_modify_header_dealloc,
+	.create_match_definer = mlx5_cmd_dr_create_match_definer,
+	.destroy_match_definer = mlx5_cmd_dr_destroy_match_definer,
 	.set_peer = mlx5_cmd_dr_set_peer,
 	.create_ns = mlx5_cmd_dr_create_ns,
 	.destroy_ns = mlx5_cmd_dr_destroy_ns,
+	.get_capabilities = mlx5_cmd_dr_get_capabilities,
 };
 
 const struct mlx5_flow_cmds *mlx5_fs_cmd_get_dr_cmds(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/mlx5_ifc_dr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/mlx5_ifc_dr.h
@@ -447,6 +447,14 @@
 	u8         flex_parser_4[0x20];
 };
 
+struct mlx5_ifc_ste_flex_parser_ok_bits {
+	u8         flex_parser_3[0x20];
+	u8         flex_parser_2[0x20];
+	u8         flex_parsers_ok[0x8];
+	u8         reserved_at_48[0x18];
+	u8         flex_parser_0[0x20];
+};
+
 struct mlx5_ifc_ste_flex_parser_tnl_bits {
 	u8         flex_parser_tunneling_header_63_32[0x20];
 
@@ -489,6 +497,14 @@
 
 	u8	   reserved_at_40[0x40];
 };
+
+struct mlx5_ifc_ste_tunnel_header_bits {
+	u8	   tunnel_header_0[0x20];
+
+	u8	   tunnel_header_1[0x20];
+
+	u8	   reserved_at_40[0x40];
+};
 
 struct mlx5_ifc_ste_general_purpose_bits {
 	u8         general_purpose_lookup_field[0x20];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/steering/mlx5dr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/steering/mlx5dr.h
@@ -89,14 +89,15 @@
 
 struct mlx5dr_action *
 mlx5dr_action_create_dest_vport(struct mlx5dr_domain *domain,
-				u32 vport, u8 vhca_id_valid,
+				u16 vport, u8 vhca_id_valid,
 				u16 vhca_id);
 
 struct mlx5dr_action *
 mlx5dr_action_create_mult_dest_tbl(struct mlx5dr_domain *dmn,
 				   struct mlx5dr_action_dest *dests,
 				   u32 num_of_dests,
-				   bool ignore_flow_level);
+				   bool ignore_flow_level,
+				   u32 flow_source);
 
 struct mlx5dr_action *mlx5dr_action_create_drop(void);
 
@@ -136,7 +137,7 @@
 	       (MLX5_CAP_ESW_FLOWTABLE_FDB(dev, sw_owner) ||
 		(MLX5_CAP_ESW_FLOWTABLE_FDB(dev, sw_owner_v2) &&
 		 (MLX5_CAP_GEN(dev, steering_format_version) <=
-		  MLX5_STEERING_FORMAT_CONNECTX_6DX)));
+		  MLX5_STEERING_FORMAT_CONNECTX_7)));
 }
 
 /* buddy functions & structure */
@@ -160,6 +161,11 @@
 	 * sync_ste command sets them free.
 	 */
 	struct list_head	hot_list;
+
+	/* Memory optimisation */
+	struct mlx5dr_ste	*ste_arr;
+	struct list_head	*miss_list;
+	u8			*hw_ste_arr;
 };
 
 int mlx5dr_buddy_init(struct mlx5dr_icm_buddy_mem *buddy,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlx5/core/vport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlx5/core/vport.c
@@ -277,7 +277,7 @@
 		req_list_size = max_list_size;
 	}
 
-	out_sz = MLX5_ST_SZ_BYTES(query_nic_vport_context_in) +
+	out_sz = MLX5_ST_SZ_BYTES(query_nic_vport_context_out) +
 			req_list_size * MLX5_ST_SZ_BYTES(mac_address_layout);
 
 	out = kzalloc(out_sz, GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxbf_gige/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxbf_gige/Makefile
@@ -3,7 +3,6 @@
 obj-$(CONFIG_MLXBF_GIGE) += mlxbf_gige.o
 
 mlxbf_gige-y := mlxbf_gige_ethtool.o \
-		mlxbf_gige_gpio.o \
 		mlxbf_gige_intr.o \
 		mlxbf_gige_main.o \
 		mlxbf_gige_mdio.o \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
@@ -39,6 +39,7 @@
  */
 #define MLXBF_GIGE_BCAST_MAC_FILTER_IDX 0
 #define MLXBF_GIGE_LOCAL_MAC_FILTER_IDX 1
+#define MLXBF_GIGE_MAX_FILTER_IDX       3
 
 /* Define for broadcast MAC literal */
 #define BCAST_MAC_ADDR 0xFFFFFFFFFFFF
@@ -51,11 +52,6 @@
 #define MLXBF_GIGE_ERROR_INTR_IDX       0
 #define MLXBF_GIGE_RECEIVE_PKT_INTR_IDX 1
 #define MLXBF_GIGE_LLU_PLU_INTR_IDX     2
-#define MLXBF_GIGE_PHY_INT_N            3
-
-#define MLXBF_GIGE_MDIO_DEFAULT_PHY_ADDR 0x3
-
-#define MLXBF_GIGE_DEFAULT_PHY_INT_GPIO 12
 
 struct mlxbf_gige_stats {
 	u64 hw_access_errors;
@@ -80,12 +76,9 @@
 	struct net_device *netdev;
 	struct platform_device *pdev;
 	void __iomem *mdio_io;
+	void __iomem *clk_io;
 	struct mii_bus *mdiobus;
-	void __iomem *gpio_io;
-	struct irq_domain *irqdomain;
-	u32 phy_int_gpio_mask;
 	spinlock_t lock;      /* for packet processing indices */
-	spinlock_t gpio_lock; /* for GPIO bus access */
 	u16 rx_q_entries;
 	u16 tx_q_entries;
 	u64 *tx_wqe_base;
@@ -149,7 +142,8 @@
 	MLXBF_GIGE_RES_MDIO9,
 	MLXBF_GIGE_RES_GPIO0,
 	MLXBF_GIGE_RES_LLU,
-	MLXBF_GIGE_RES_PLU
+	MLXBF_GIGE_RES_PLU,
+	MLXBF_GIGE_RES_CLK
 };
 
 /* Version of register data returned by mlxbf_gige_get_regs() */
@@ -158,9 +152,13 @@
 int mlxbf_gige_mdio_probe(struct platform_device *pdev,
 			  struct mlxbf_gige *priv);
 void mlxbf_gige_mdio_remove(struct mlxbf_gige *priv);
-irqreturn_t mlxbf_gige_mdio_handle_phy_interrupt(int irq, void *dev_id);
-void mlxbf_gige_mdio_enable_phy_int(struct mlxbf_gige *priv);
 
+void mlxbf_gige_enable_multicast_rx(struct mlxbf_gige *priv);
+void mlxbf_gige_disable_multicast_rx(struct mlxbf_gige *priv);
+void mlxbf_gige_enable_mac_rx_filter(struct mlxbf_gige *priv,
+				     unsigned int index);
+void mlxbf_gige_disable_mac_rx_filter(struct mlxbf_gige *priv,
+				      unsigned int index);
 void mlxbf_gige_set_mac_rx_filter(struct mlxbf_gige *priv,
 				  unsigned int index, u64 dmac);
 void mlxbf_gige_get_mac_rx_filter(struct mlxbf_gige *priv,
@@ -184,7 +182,4 @@
 extern const struct ethtool_ops mlxbf_gige_ethtool_ops;
 void mlxbf_gige_update_tx_wqe_next(struct mlxbf_gige *priv);
 
-int mlxbf_gige_gpio_init(struct platform_device *pdev, struct mlxbf_gige *priv);
-void mlxbf_gige_gpio_free(struct mlxbf_gige *priv);
-
 #endif /* !defined(__MLXBF_GIGE_H__) */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
@@ -14,6 +14,7 @@
 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/platform_device.h>
+#include <linux/rtnetlink.h>
 #include <linux/skbuff.h>
 
 #include "mlxbf_gige.h"
@@ -75,7 +76,7 @@
 	u64_to_ether_addr(local_mac, mac);
 
 	if (is_valid_ether_addr(mac)) {
-		ether_addr_copy(priv->netdev->dev_addr, mac);
+		eth_hw_addr_set(priv->netdev, mac);
 	} else {
 		/* Provide a random MAC if for some reason the device has
 		 * not been configured with a valid MAC address already.
@@ -132,16 +133,19 @@
 {
 	struct mlxbf_gige *priv = netdev_priv(netdev);
 	struct phy_device *phydev = netdev->phydev;
+	u64 control;
 	u64 int_en;
 	int err;
 
-	err = mlxbf_gige_request_irqs(priv);
-	if (err)
-		return err;
+	/* Perform general init of GigE block */
+	control = readq(priv->base + MLXBF_GIGE_CONTROL);
+	control |= MLXBF_GIGE_CONTROL_PORT_EN;
+	writeq(control, priv->base + MLXBF_GIGE_CONTROL);
+
 	mlxbf_gige_cache_stats(priv);
 	err = mlxbf_gige_clean_port(priv);
 	if (err)
-		goto free_irqs;
+		return err;
 
 	/* Clear driver's valid_polarity to match hardware,
 	 * since the above call to clean_port() resets the
@@ -149,19 +153,27 @@
 	 */
 	priv->valid_polarity = 0;
 
-	err = mlxbf_gige_rx_init(priv);
-	if (err)
-		goto free_irqs;
+	phy_start(phydev);
+
 	err = mlxbf_gige_tx_init(priv);
 	if (err)
-		goto rx_deinit;
-
-	phy_start(phydev);
+		goto phy_deinit;
+	err = mlxbf_gige_rx_init(priv);
+	if (err)
+		goto tx_deinit;
 
 	netif_napi_add(netdev, &priv->napi, mlxbf_gige_poll, NAPI_POLL_WEIGHT);
 	napi_enable(&priv->napi);
 	netif_start_queue(netdev);
 
+	err = mlxbf_gige_request_irqs(priv);
+	if (err)
+		goto napi_deinit;
+
+	mlxbf_gige_enable_mac_rx_filter(priv, MLXBF_GIGE_BCAST_MAC_FILTER_IDX);
+	mlxbf_gige_enable_mac_rx_filter(priv, MLXBF_GIGE_LOCAL_MAC_FILTER_IDX);
+	mlxbf_gige_enable_multicast_rx(priv);
+
 	/* Set bits in INT_EN that we care about */
 	int_en = MLXBF_GIGE_INT_EN_HW_ACCESS_ERROR |
 		 MLXBF_GIGE_INT_EN_TX_CHECKSUM_INPUTS |
@@ -178,11 +190,17 @@
 
 	return 0;
 
-rx_deinit:
+napi_deinit:
+	netif_stop_queue(netdev);
+	napi_disable(&priv->napi);
+	netif_napi_del(&priv->napi);
 	mlxbf_gige_rx_deinit(priv);
 
-free_irqs:
-	mlxbf_gige_free_irqs(priv);
+tx_deinit:
+	mlxbf_gige_tx_deinit(priv);
+
+phy_deinit:
+	phy_stop(phydev);
 	return err;
 }
 
@@ -280,8 +298,8 @@
 	void __iomem *llu_base;
 	void __iomem *plu_base;
 	void __iomem *base;
-	u64 control;
-	int addr;
+	int addr, phy_irq;
+	unsigned int i;
 	int err;
 
 	base = devm_platform_ioremap_resource(pdev, MLXBF_GIGE_RES_MAC);
@@ -296,11 +314,6 @@
 	if (IS_ERR(plu_base))
 		return PTR_ERR(plu_base);
 
-	/* Perform general init of GigE block */
-	control = readq(base + MLXBF_GIGE_CONTROL);
-	control |= MLXBF_GIGE_CONTROL_PORT_EN;
-	writeq(control, base + MLXBF_GIGE_CONTROL);
-
 	netdev = devm_alloc_etherdev(&pdev->dev, sizeof(*priv));
 	if (!netdev)
 		return -ENOMEM;
@@ -316,20 +329,12 @@
 	priv->pdev = pdev;
 
 	spin_lock_init(&priv->lock);
-	spin_lock_init(&priv->gpio_lock);
 
 	/* Attach MDIO device */
 	err = mlxbf_gige_mdio_probe(pdev, priv);
 	if (err)
 		return err;
 
-	err = mlxbf_gige_gpio_init(pdev, priv);
-	if (err) {
-		dev_err(&pdev->dev, "PHY IRQ initialization failed\n");
-		mlxbf_gige_mdio_remove(priv);
-		return -ENODEV;
-	}
-
 	priv->base = base;
 	priv->llu_base = llu_base;
 	priv->plu_base = plu_base;
@@ -337,6 +342,11 @@
 	priv->rx_q_entries = MLXBF_GIGE_DEFAULT_RXQ_SZ;
 	priv->tx_q_entries = MLXBF_GIGE_DEFAULT_TXQ_SZ;
 
+	for (i = 0; i <= MLXBF_GIGE_MAX_FILTER_IDX; i++)
+		mlxbf_gige_disable_mac_rx_filter(priv, i);
+	mlxbf_gige_disable_multicast_rx(priv);
+	mlxbf_gige_disable_promisc(priv);
+
 	/* Write initial MAC address to hardware */
 	mlxbf_gige_initial_mac(priv);
 
@@ -350,6 +360,12 @@
 	priv->rx_irq = platform_get_irq(pdev, MLXBF_GIGE_RECEIVE_PKT_INTR_IDX);
 	priv->llu_plu_irq = platform_get_irq(pdev, MLXBF_GIGE_LLU_PLU_INTR_IDX);
 
+	phy_irq = acpi_dev_gpio_irq_get_by(ACPI_COMPANION(&pdev->dev), "phy-gpios", 0);
+	if (phy_irq < 0) {
+		dev_err(&pdev->dev, "Error getting PHY irq. Use polling instead");
+		phy_irq = PHY_POLL;
+	}
+
 	phydev = phy_find_first(priv->mdiobus);
 	if (!phydev) {
 		err = -ENODEV;
@@ -357,8 +373,8 @@
 	}
 
 	addr = phydev->mdio.addr;
-	priv->mdiobus->irq[addr] = priv->phy_irq;
-	phydev->irq = priv->phy_irq;
+	priv->mdiobus->irq[addr] = phy_irq;
+	phydev->irq = phy_irq;
 
 	err = phy_connect_direct(netdev, phydev,
 				 mlxbf_gige_adjust_link,
@@ -394,7 +410,6 @@
 	return 0;
 
 out:
-	mlxbf_gige_gpio_free(priv);
 	mlxbf_gige_mdio_remove(priv);
 	return err;
 }
@@ -405,7 +420,6 @@
 
 	unregister_netdev(priv->netdev);
 	phy_disconnect(priv->netdev->phydev);
-	mlxbf_gige_gpio_free(priv);
 	mlxbf_gige_mdio_remove(priv);
 	platform_set_drvdata(pdev, NULL);
 
@@ -416,8 +430,13 @@
 {
 	struct mlxbf_gige *priv = platform_get_drvdata(pdev);
 
-	writeq(0, priv->base + MLXBF_GIGE_INT_EN);
-	mlxbf_gige_clean_port(priv);
+	rtnl_lock();
+	netif_device_detach(priv->netdev);
+
+	if (netif_running(priv->netdev))
+		dev_close(priv->netdev);
+
+	rtnl_unlock();
 }
 
 static const struct acpi_device_id __maybe_unused mlxbf_gige_acpi_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_mdio.c
@@ -22,10 +22,23 @@
 #include <linux/property.h>
 
 #include "mlxbf_gige.h"
+#include "mlxbf_gige_regs.h"
 
 #define MLXBF_GIGE_MDIO_GW_OFFSET	0x0
 #define MLXBF_GIGE_MDIO_CFG_OFFSET	0x4
 
+#define MLXBF_GIGE_MDIO_FREQ_REFERENCE 156250000ULL
+#define MLXBF_GIGE_MDIO_COREPLL_CONST  16384ULL
+#define MLXBF_GIGE_MDC_CLK_NS          400
+#define MLXBF_GIGE_MDIO_PLL_I1CLK_REG1 0x4
+#define MLXBF_GIGE_MDIO_PLL_I1CLK_REG2 0x8
+#define MLXBF_GIGE_MDIO_CORE_F_SHIFT   0
+#define MLXBF_GIGE_MDIO_CORE_F_MASK    GENMASK(25, 0)
+#define MLXBF_GIGE_MDIO_CORE_R_SHIFT   26
+#define MLXBF_GIGE_MDIO_CORE_R_MASK    GENMASK(31, 26)
+#define MLXBF_GIGE_MDIO_CORE_OD_SHIFT  0
+#define MLXBF_GIGE_MDIO_CORE_OD_MASK   GENMASK(3, 0)
+
 /* Support clause 22 */
 #define MLXBF_GIGE_MDIO_CL22_ST1	0x1
 #define MLXBF_GIGE_MDIO_CL22_WRITE	0x1
@@ -50,27 +63,76 @@
 #define MLXBF_GIGE_MDIO_CFG_MDIO_IN_SAMP_MASK		GENMASK(23, 16)
 #define MLXBF_GIGE_MDIO_CFG_MDIO_OUT_SAMP_MASK		GENMASK(31, 24)
 
+#define MLXBF_GIGE_MDIO_CFG_VAL (FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_MODE_MASK, 1) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO3_3_MASK, 1) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_FULL_DRIVE_MASK, 1) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_IN_SAMP_MASK, 6) | \
+				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_OUT_SAMP_MASK, 13))
+
+#define MLXBF_GIGE_BF2_COREPLL_ADDR 0x02800c30
+#define MLXBF_GIGE_BF2_COREPLL_SIZE 0x0000000c
+
+static struct resource corepll_params[] = {
+	[MLXBF_GIGE_VERSION_BF2] = {
+		.start = MLXBF_GIGE_BF2_COREPLL_ADDR,
+		.end = MLXBF_GIGE_BF2_COREPLL_ADDR + MLXBF_GIGE_BF2_COREPLL_SIZE - 1,
+		.name = "COREPLL_RES"
+	},
+};
+
+/* Returns core clock i1clk in Hz */
+static u64 calculate_i1clk(struct mlxbf_gige *priv)
+{
+	u8 core_od, core_r;
+	u64 freq_output;
+	u32 reg1, reg2;
+	u32 core_f;
+
+	reg1 = readl(priv->clk_io + MLXBF_GIGE_MDIO_PLL_I1CLK_REG1);
+	reg2 = readl(priv->clk_io + MLXBF_GIGE_MDIO_PLL_I1CLK_REG2);
+
+	core_f = (reg1 & MLXBF_GIGE_MDIO_CORE_F_MASK) >>
+		MLXBF_GIGE_MDIO_CORE_F_SHIFT;
+	core_r = (reg1 & MLXBF_GIGE_MDIO_CORE_R_MASK) >>
+		MLXBF_GIGE_MDIO_CORE_R_SHIFT;
+	core_od = (reg2 & MLXBF_GIGE_MDIO_CORE_OD_MASK) >>
+		MLXBF_GIGE_MDIO_CORE_OD_SHIFT;
+
+	/* Compute PLL output frequency as follow:
+	 *
+	 *                                     CORE_F / 16384
+	 * freq_output = freq_reference * ----------------------------
+	 *                              (CORE_R + 1) * (CORE_OD + 1)
+	 */
+	freq_output = div_u64((MLXBF_GIGE_MDIO_FREQ_REFERENCE * core_f),
+			      MLXBF_GIGE_MDIO_COREPLL_CONST);
+	freq_output = div_u64(freq_output, (core_r + 1) * (core_od + 1));
+
+	return freq_output;
+}
+
 /* Formula for encoding the MDIO period. The encoded value is
  * passed to the MDIO config register.
  *
- * mdc_clk = 2*(val + 1)*i1clk
+ * mdc_clk = 2*(val + 1)*(core clock in sec)
  *
- * 400 ns = 2*(val + 1)*(((1/430)*1000) ns)
+ * i1clk is in Hz:
+ * 400 ns = 2*(val + 1)*(1/i1clk)
  *
- * val = (((400 * 430 / 1000) / 2) - 1)
+ * val = (((400/10^9) / (1/i1clk) / 2) - 1)
+ * val = (400/2 * i1clk)/10^9 - 1
  */
-#define MLXBF_GIGE_I1CLK_MHZ		430
-#define MLXBF_GIGE_MDC_CLK_NS		400
+static u8 mdio_period_map(struct mlxbf_gige *priv)
+{
+	u8 mdio_period;
+	u64 i1clk;
 
-#define MLXBF_GIGE_MDIO_PERIOD	(((MLXBF_GIGE_MDC_CLK_NS * MLXBF_GIGE_I1CLK_MHZ / 1000) / 2) - 1)
+	i1clk = calculate_i1clk(priv);
 
-#define MLXBF_GIGE_MDIO_CFG_VAL (FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_MODE_MASK, 1) | \
-				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO3_3_MASK, 1) | \
-				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_FULL_DRIVE_MASK, 1) | \
-				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDC_PERIOD_MASK, \
-					    MLXBF_GIGE_MDIO_PERIOD) | \
-				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_IN_SAMP_MASK, 6) | \
-				 FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDIO_OUT_SAMP_MASK, 13))
+	mdio_period = div_u64((MLXBF_GIGE_MDC_CLK_NS >> 1) * i1clk, 1000000000) - 1;
+
+	return mdio_period;
+}
 
 static u32 mlxbf_gige_mdio_create_cmd(u16 data, int phy_add,
 				      int phy_reg, u32 opcode)
@@ -116,6 +178,9 @@
 	/* Only return ad bits of the gw register */
 	ret &= MLXBF_GIGE_MDIO_GW_AD_MASK;
 
+	/* The MDIO lock is set on read. To release it, clear gw register */
+	writel(0, priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET);
+
 	return ret;
 }
 
@@ -123,9 +188,9 @@
 				 int phy_reg, u16 val)
 {
 	struct mlxbf_gige *priv = bus->priv;
+	u32 temp;
 	u32 cmd;
 	int ret;
-	u32 temp;
 
 	if (phy_reg & MII_ADDR_C45)
 		return -EOPNOTSUPP;
@@ -139,21 +204,50 @@
 	ret = readl_poll_timeout_atomic(priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET,
 					temp, !(temp & MLXBF_GIGE_MDIO_GW_BUSY_MASK), 100, 1000000);
 
+	/* The MDIO lock is set on read. To release it, clear gw register */
+	writel(0, priv->mdio_io + MLXBF_GIGE_MDIO_GW_OFFSET);
+
 	return ret;
 }
 
+static void mlxbf_gige_mdio_cfg(struct mlxbf_gige *priv)
+{
+	u8 mdio_period;
+	u32 val;
+
+	mdio_period = mdio_period_map(priv);
+
+	val = MLXBF_GIGE_MDIO_CFG_VAL;
+	val |= FIELD_PREP(MLXBF_GIGE_MDIO_CFG_MDC_PERIOD_MASK, mdio_period);
+	writel(val, priv->mdio_io + MLXBF_GIGE_MDIO_CFG_OFFSET);
+}
+
 int mlxbf_gige_mdio_probe(struct platform_device *pdev, struct mlxbf_gige *priv)
 {
 	struct device *dev = &pdev->dev;
+	struct resource *res;
 	int ret;
 
 	priv->mdio_io = devm_platform_ioremap_resource(pdev, MLXBF_GIGE_RES_MDIO9);
 	if (IS_ERR(priv->mdio_io))
 		return PTR_ERR(priv->mdio_io);
 
-	/* Configure mdio parameters */
-	writel(MLXBF_GIGE_MDIO_CFG_VAL,
-	       priv->mdio_io + MLXBF_GIGE_MDIO_CFG_OFFSET);
+	/* clk resource shared with other drivers so cannot use
+	 * devm_platform_ioremap_resource
+	 */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_CLK);
+	if (!res) {
+		/* For backward compatibility with older ACPI tables, also keep
+		 * CLK resource internal to the driver.
+		 */
+		res = &corepll_params[MLXBF_GIGE_VERSION_BF2];
+	}
+
+	priv->clk_io = devm_ioremap(dev, res->start, resource_size(res));
+	if (!priv->clk_io)
+		return -ENOMEM;
+
+	mlxbf_gige_mdio_cfg(priv);
 
 	priv->mdiobus = devm_mdiobus_alloc(dev);
 	if (!priv->mdiobus) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
@@ -8,6 +8,8 @@
 #ifndef __MLXBF_GIGE_REGS_H__
 #define __MLXBF_GIGE_REGS_H__
 
+#define MLXBF_GIGE_VERSION                            0x0000
+#define MLXBF_GIGE_VERSION_BF2                        0x0
 #define MLXBF_GIGE_STATUS                             0x0010
 #define MLXBF_GIGE_STATUS_READY                       BIT(0)
 #define MLXBF_GIGE_INT_STATUS                         0x0028
@@ -57,6 +59,8 @@
 #define MLXBF_GIGE_TX_STATUS_DATA_FIFO_FULL           BIT(1)
 #define MLXBF_GIGE_RX_MAC_FILTER_DMAC_RANGE_START     0x0520
 #define MLXBF_GIGE_RX_MAC_FILTER_DMAC_RANGE_END       0x0528
+#define MLXBF_GIGE_RX_MAC_FILTER_GENERAL              0x0530
+#define MLXBF_GIGE_RX_MAC_FILTER_EN_MULTICAST         BIT(1)
 #define MLXBF_GIGE_RX_MAC_FILTER_COUNT_DISC           0x0540
 #define MLXBF_GIGE_RX_MAC_FILTER_COUNT_DISC_EN        BIT(0)
 #define MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS           0x0548
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_rx.c
@@ -11,15 +11,31 @@
 #include "mlxbf_gige.h"
 #include "mlxbf_gige_regs.h"
 
-void mlxbf_gige_set_mac_rx_filter(struct mlxbf_gige *priv,
-				  unsigned int index, u64 dmac)
+void mlxbf_gige_enable_multicast_rx(struct mlxbf_gige *priv)
 {
 	void __iomem *base = priv->base;
-	u64 control;
+	u64 data;
 
-	/* Write destination MAC to specified MAC RX filter */
-	writeq(dmac, base + MLXBF_GIGE_RX_MAC_FILTER +
-	       (index * MLXBF_GIGE_RX_MAC_FILTER_STRIDE));
+	data = readq(base + MLXBF_GIGE_RX_MAC_FILTER_GENERAL);
+	data |= MLXBF_GIGE_RX_MAC_FILTER_EN_MULTICAST;
+	writeq(data, base + MLXBF_GIGE_RX_MAC_FILTER_GENERAL);
+}
+
+void mlxbf_gige_disable_multicast_rx(struct mlxbf_gige *priv)
+{
+	void __iomem *base = priv->base;
+	u64 data;
+
+	data = readq(base + MLXBF_GIGE_RX_MAC_FILTER_GENERAL);
+	data &= ~MLXBF_GIGE_RX_MAC_FILTER_EN_MULTICAST;
+	writeq(data, base + MLXBF_GIGE_RX_MAC_FILTER_GENERAL);
+}
+
+void mlxbf_gige_enable_mac_rx_filter(struct mlxbf_gige *priv,
+				     unsigned int index)
+{
+	void __iomem *base = priv->base;
+	u64 control;
 
 	/* Enable MAC receive filter mask for specified index */
 	control = readq(base + MLXBF_GIGE_CONTROL);
@@ -27,6 +43,28 @@
 	writeq(control, base + MLXBF_GIGE_CONTROL);
 }
 
+void mlxbf_gige_disable_mac_rx_filter(struct mlxbf_gige *priv,
+				      unsigned int index)
+{
+	void __iomem *base = priv->base;
+	u64 control;
+
+	/* Disable MAC receive filter mask for specified index */
+	control = readq(base + MLXBF_GIGE_CONTROL);
+	control &= ~(MLXBF_GIGE_CONTROL_EN_SPECIFIC_MAC << index);
+	writeq(control, base + MLXBF_GIGE_CONTROL);
+}
+
+void mlxbf_gige_set_mac_rx_filter(struct mlxbf_gige *priv,
+				  unsigned int index, u64 dmac)
+{
+	void __iomem *base = priv->base;
+
+	/* Write destination MAC to specified MAC RX filter */
+	writeq(dmac, base + MLXBF_GIGE_RX_MAC_FILTER +
+	       (index * MLXBF_GIGE_RX_MAC_FILTER_STRIDE));
+}
+
 void mlxbf_gige_get_mac_rx_filter(struct mlxbf_gige *priv,
 				  unsigned int index, u64 *dmac)
 {
@@ -142,6 +180,9 @@
 	writeq(MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS_EN,
 	       priv->base + MLXBF_GIGE_RX_MAC_FILTER_COUNT_PASS);
 
+	writeq(ilog2(priv->rx_q_entries),
+	       priv->base + MLXBF_GIGE_RX_WQE_SIZE_LOG2);
+
 	/* Clear MLXBF_GIGE_INT_MASK 'receive pkt' bit to
 	 * indicate readiness to receive interrupts
 	 */
@@ -154,9 +195,6 @@
 	data |= MLXBF_GIGE_RX_DMA_EN;
 	writeq(data, priv->base + MLXBF_GIGE_RX_DMA);
 
-	writeq(ilog2(priv->rx_q_entries),
-	       priv->base + MLXBF_GIGE_RX_WQE_SIZE_LOG2);
-
 	return 0;
 
 free_wqe_and_skb:
@@ -245,12 +283,6 @@
 
 		skb = priv->rx_skb[rx_pi_rem];
 
-		skb_put(skb, datalen);
-
-		skb->ip_summed = CHECKSUM_NONE; /* device did not checksum packet */
-
-		skb->protocol = eth_type_trans(skb, netdev);
-
 		/* Alloc another RX SKB for this same index */
 		rx_skb = mlxbf_gige_alloc_skb(priv, MLXBF_GIGE_DEFAULT_BUF_SZ,
 					      &rx_buf_dma, DMA_FROM_DEVICE);
@@ -259,6 +291,13 @@
 		priv->rx_skb[rx_pi_rem] = rx_skb;
 		dma_unmap_single(priv->dev, *rx_wqe_addr,
 				 MLXBF_GIGE_DEFAULT_BUF_SZ, DMA_FROM_DEVICE);
+
+		skb_put(skb, datalen);
+
+		skb->ip_summed = CHECKSUM_NONE; /* device did not checksum packet */
+
+		skb->protocol = eth_type_trans(skb, netdev);
+
 		*rx_wqe_addr = rx_buf_dma;
 	} else if (rx_cqe & MLXBF_GIGE_RX_CQE_PKT_STATUS_MAC_ERR) {
 		priv->stats.rx_mac_errors++;
@@ -266,6 +305,13 @@
 		priv->stats.rx_truncate_errors++;
 	}
 
+	/* Read receive consumer index before replenish so that this routine
+	 * returns accurate return value even if packet is received into
+	 * just-replenished buffer prior to exiting this routine.
+	 */
+	rx_ci = readq(priv->base + MLXBF_GIGE_RX_CQE_PACKET_CI);
+	rx_ci_rem = rx_ci % priv->rx_q_entries;
+
 	/* Let hardware know we've replenished one buffer */
 	rx_pi++;
 
@@ -278,8 +324,6 @@
 	rx_pi_rem = rx_pi % priv->rx_q_entries;
 	if (rx_pi_rem == 0)
 		priv->valid_polarity ^= 1;
-	rx_ci = readq(priv->base + MLXBF_GIGE_RX_CQE_PACKET_CI);
-	rx_ci_rem = rx_ci % priv->rx_q_entries;
 
 	if (skb)
 		netif_receive_skb(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxfw/mlxfw_fsm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxfw/mlxfw_fsm.c
@@ -14,7 +14,6 @@
 #define MLXFW_FSM_STATE_WAIT_TIMEOUT_MS 30000
 #define MLXFW_FSM_STATE_WAIT_ROUNDS \
 	(MLXFW_FSM_STATE_WAIT_TIMEOUT_MS / MLXFW_FSM_STATE_WAIT_CYCLE_MS)
-#define MLXFW_FSM_MAX_COMPONENT_SIZE (10 * (1 << 20))
 
 static const int mlxfw_fsm_state_errno[] = {
 	[MLXFW_FSM_STATE_ERR_ERROR] = -EIO,
@@ -229,7 +228,6 @@
 		return err;
 	}
 
-	comp_max_size = min_t(u32, comp_max_size, MLXFW_FSM_MAX_COMPONENT_SIZE);
 	if (comp->data_size > comp_max_size) {
 		MLXFW_ERR_MSG(mlxfw_dev, extack,
 			      "Component size is bigger than limit", -EINVAL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxfw/mlxfw_mfa2_tlv_multi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxfw/mlxfw_mfa2_tlv_multi.c
@@ -31,6 +31,8 @@
 
 	if (tlv->type == MLXFW_MFA2_TLV_MULTI_PART) {
 		multi = mlxfw_mfa2_tlv_multi_get(mfa2_file, tlv);
+		if (!multi)
+			return NULL;
 		tlv_len = NLA_ALIGN(tlv_len + be16_to_cpu(multi->total_len));
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/cmd.h
@@ -935,6 +935,18 @@
  */
 MLXSW_ITEM32(cmd_mbox, sw2hw_dq, cq, 0x00, 24, 8);
 
+enum mlxsw_cmd_mbox_sw2hw_dq_sdq_lp {
+	MLXSW_CMD_MBOX_SW2HW_DQ_SDQ_LP_WQE,
+	MLXSW_CMD_MBOX_SW2HW_DQ_SDQ_LP_IGNORE_WQE,
+};
+
+/* cmd_mbox_sw2hw_dq_sdq_lp
+ * SDQ local Processing
+ * 0: local processing by wqe.lp
+ * 1: local processing (ignoring wqe.lp)
+ */
+MLXSW_ITEM32(cmd_mbox, sw2hw_dq, sdq_lp, 0x00, 23, 1);
+
 /* cmd_mbox_sw2hw_dq_sdq_tclass
  * SDQ: CPU Egress TClass
  * RDQ: Reserved
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/core.c
@@ -746,7 +746,7 @@
 
 static const struct mlxsw_listener mlxsw_emad_rx_listener =
 	MLXSW_RXL(mlxsw_emad_rx_listener_func, ETHEMAD, TRAP_TO_CPU, false,
-		  EMAD, DISCARD);
+		  EMAD, FORWARD);
 
 static int mlxsw_emad_init(struct mlxsw_core *mlxsw_core)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/i2c.c
@@ -47,6 +47,7 @@
 #define MLXSW_I2C_MBOX_SIZE_BITS	12
 #define MLXSW_I2C_ADDR_BUF_SIZE		4
 #define MLXSW_I2C_BLK_DEF		32
+#define MLXSW_I2C_BLK_MAX		100
 #define MLXSW_I2C_RETRY			5
 #define MLXSW_I2C_TIMEOUT_MSECS		5000
 #define MLXSW_I2C_MAX_DATA_SIZE		256
@@ -428,7 +429,7 @@
 	} else {
 		/* No input mailbox is case of initialization query command. */
 		reg_size = MLXSW_I2C_MAX_DATA_SIZE;
-		num = reg_size / mlxsw_i2c->block_size;
+		num = DIV_ROUND_UP(reg_size, mlxsw_i2c->block_size);
 
 		if (mutex_lock_interruptible(&mlxsw_i2c->cmd.lock) < 0) {
 			dev_err(&client->dev, "Could not acquire lock");
@@ -576,7 +577,7 @@
 			return -EOPNOTSUPP;
 		}
 
-		mlxsw_i2c->block_size = max_t(u16, MLXSW_I2C_BLK_DEF,
+		mlxsw_i2c->block_size = min_t(u16, MLXSW_I2C_BLK_MAX,
 					      min_t(u16, quirks->max_read_len,
 						    quirks->max_write_len));
 	} else {
@@ -650,6 +651,7 @@
 	return 0;
 
 errout:
+	mutex_destroy(&mlxsw_i2c->cmd.lock);
 	i2c_set_clientdata(client, NULL);
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/pci.c
@@ -285,6 +285,7 @@
 			      struct mlxsw_pci_queue *q)
 {
 	int tclass;
+	int lp;
 	int i;
 	int err;
 
@@ -292,9 +293,12 @@
 	q->consumer_counter = 0;
 	tclass = q->num == MLXSW_PCI_SDQ_EMAD_INDEX ? MLXSW_PCI_SDQ_EMAD_TC :
 						      MLXSW_PCI_SDQ_CTL_TC;
+	lp = q->num == MLXSW_PCI_SDQ_EMAD_INDEX ? MLXSW_CMD_MBOX_SW2HW_DQ_SDQ_LP_IGNORE_WQE :
+						  MLXSW_CMD_MBOX_SW2HW_DQ_SDQ_LP_WQE;
 
 	/* Set CQ of same number of this SDQ. */
 	mlxsw_cmd_mbox_sw2hw_dq_cq_set(mbox, q->num);
+	mlxsw_cmd_mbox_sw2hw_dq_sdq_lp_set(mbox, lp);
 	mlxsw_cmd_mbox_sw2hw_dq_sdq_tclass_set(mbox, tclass);
 	mlxsw_cmd_mbox_sw2hw_dq_log2_dq_sz_set(mbox, 3); /* 8 pages */
 	for (i = 0; i < MLXSW_PCI_AQ_PAGES; i++) {
@@ -1678,7 +1682,7 @@
 
 	wqe = elem_info->elem;
 	mlxsw_pci_wqe_c_set(wqe, 1); /* always report completion */
-	mlxsw_pci_wqe_lp_set(wqe, !!tx_info->is_emad);
+	mlxsw_pci_wqe_lp_set(wqe, 0);
 	mlxsw_pci_wqe_type_set(wqe, MLXSW_PCI_WQE_TYPE_ETHERNET);
 
 	err = mlxsw_pci_wqe_frag_map(mlxsw_pci, wqe, 0, skb->data,
@@ -1973,6 +1977,7 @@
 {
 	pci_driver->probe = mlxsw_pci_probe;
 	pci_driver->remove = mlxsw_pci_remove;
+	pci_driver->shutdown = mlxsw_pci_remove;
 	return pci_register_driver(pci_driver);
 }
 EXPORT_SYMBOL(mlxsw_pci_driver_register);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/pci_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/pci_hw.h
@@ -26,7 +26,7 @@
 #define MLXSW_PCI_CIR_TIMEOUT_MSECS		1000
 
 #define MLXSW_PCI_SW_RESET_TIMEOUT_MSECS	900000
-#define MLXSW_PCI_SW_RESET_WAIT_MSECS		200
+#define MLXSW_PCI_SW_RESET_WAIT_MSECS		400
 #define MLXSW_PCI_FW_READY			0xA1844
 #define MLXSW_PCI_FW_READY_MASK			0xFFFF
 #define MLXSW_PCI_FW_READY_MAGIC		0x5E
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -1730,9 +1730,9 @@
 
 	cancel_delayed_work_sync(&mlxsw_sp_port->periodic_hw_stats.update_dw);
 	cancel_delayed_work_sync(&mlxsw_sp_port->ptp.shaper_dw);
-	mlxsw_sp_port_ptp_clear(mlxsw_sp_port);
 	mlxsw_core_port_clear(mlxsw_sp->core, local_port, mlxsw_sp);
 	unregister_netdev(mlxsw_sp_port->dev); /* This calls ndo_stop */
+	mlxsw_sp_port_ptp_clear(mlxsw_sp_port);
 	mlxsw_sp_port_vlan_classification_set(mlxsw_sp_port, true, true);
 	mlxsw_sp->ports[local_port] = NULL;
 	mlxsw_sp_port_vlan_flush(mlxsw_sp_port, true);
@@ -2131,7 +2131,7 @@
 	max_ports = mlxsw_core_max_ports(mlxsw_sp->core);
 	local_port = mlxsw_reg_pude_local_port_get(pude_pl);
 
-	if (WARN_ON_ONCE(local_port >= max_ports))
+	if (WARN_ON_ONCE(!local_port || local_port >= max_ports))
 		return;
 	mlxsw_sp_port = mlxsw_sp->ports[local_port];
 	if (!mlxsw_sp_port)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_atcam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_atcam.c
@@ -119,7 +119,6 @@
 {
 	struct mlxsw_sp *mlxsw_sp = aregion->region->mlxsw_sp;
 	struct mlxsw_sp_acl_atcam_region_12kb *region_12kb;
-	size_t alloc_size;
 	u64 max_lkey_id;
 	int err;
 
@@ -131,8 +130,7 @@
 	if (!region_12kb)
 		return -ENOMEM;
 
-	alloc_size = BITS_TO_LONGS(max_lkey_id) * sizeof(unsigned long);
-	region_12kb->used_lkey_id = kzalloc(alloc_size, GFP_KERNEL);
+	region_12kb->used_lkey_id = bitmap_zalloc(max_lkey_id, GFP_KERNEL);
 	if (!region_12kb->used_lkey_id) {
 		err = -ENOMEM;
 		goto err_used_lkey_id_alloc;
@@ -149,7 +147,7 @@
 	return 0;
 
 err_rhashtable_init:
-	kfree(region_12kb->used_lkey_id);
+	bitmap_free(region_12kb->used_lkey_id);
 err_used_lkey_id_alloc:
 	kfree(region_12kb);
 	return err;
@@ -161,7 +159,7 @@
 	struct mlxsw_sp_acl_atcam_region_12kb *region_12kb = aregion->priv;
 
 	rhashtable_destroy(&region_12kb->lkey_ht);
-	kfree(region_12kb->used_lkey_id);
+	bitmap_free(region_12kb->used_lkey_id);
 	kfree(region_12kb);
 }
 
@@ -393,7 +391,8 @@
 	if (err)
 		return err;
 
-	lkey_id = aregion->ops->lkey_id_get(aregion, aentry->enc_key, erp_id);
+	lkey_id = aregion->ops->lkey_id_get(aregion, aentry->ht_key.enc_key,
+					    erp_id);
 	if (IS_ERR(lkey_id))
 		return PTR_ERR(lkey_id);
 	aentry->lkey_id = lkey_id;
@@ -401,7 +400,7 @@
 	kvdl_index = mlxsw_afa_block_first_kvdl_index(rulei->act_block);
 	mlxsw_reg_ptce3_pack(ptce3_pl, true, MLXSW_REG_PTCE3_OP_WRITE_WRITE,
 			     priority, region->tcam_region_info,
-			     aentry->enc_key, erp_id,
+			     aentry->ht_key.enc_key, erp_id,
 			     aentry->delta_info.start,
 			     aentry->delta_info.mask,
 			     aentry->delta_info.value,
@@ -430,7 +429,7 @@
 
 	mlxsw_reg_ptce3_pack(ptce3_pl, false, MLXSW_REG_PTCE3_OP_WRITE_WRITE, 0,
 			     region->tcam_region_info,
-			     aentry->enc_key, erp_id,
+			     aentry->ht_key.enc_key, erp_id,
 			     aentry->delta_info.start,
 			     aentry->delta_info.mask,
 			     aentry->delta_info.value,
@@ -459,7 +458,7 @@
 	kvdl_index = mlxsw_afa_block_first_kvdl_index(rulei->act_block);
 	mlxsw_reg_ptce3_pack(ptce3_pl, true, MLXSW_REG_PTCE3_OP_WRITE_UPDATE,
 			     priority, region->tcam_region_info,
-			     aentry->enc_key, erp_id,
+			     aentry->ht_key.enc_key, erp_id,
 			     aentry->delta_info.start,
 			     aentry->delta_info.mask,
 			     aentry->delta_info.value,
@@ -482,15 +481,13 @@
 	int err;
 
 	mlxsw_afk_encode(afk, region->key_info, &rulei->values,
-			 aentry->ht_key.full_enc_key, mask);
+			 aentry->ht_key.enc_key, mask);
 
 	erp_mask = mlxsw_sp_acl_erp_mask_get(aregion, mask, false);
 	if (IS_ERR(erp_mask))
 		return PTR_ERR(erp_mask);
 	aentry->erp_mask = erp_mask;
 	aentry->ht_key.erp_id = mlxsw_sp_acl_erp_mask_erp_id(erp_mask);
-	memcpy(aentry->enc_key, aentry->ht_key.full_enc_key,
-	       sizeof(aentry->enc_key));
 
 	/* Compute all needed delta information and clear the delta bits
 	 * from the encrypted key.
@@ -499,9 +496,8 @@
 	aentry->delta_info.start = mlxsw_sp_acl_erp_delta_start(delta);
 	aentry->delta_info.mask = mlxsw_sp_acl_erp_delta_mask(delta);
 	aentry->delta_info.value =
-		mlxsw_sp_acl_erp_delta_value(delta,
-					     aentry->ht_key.full_enc_key);
-	mlxsw_sp_acl_erp_delta_clear(delta, aentry->enc_key);
+		mlxsw_sp_acl_erp_delta_value(delta, aentry->ht_key.enc_key);
+	mlxsw_sp_acl_erp_delta_clear(delta, aentry->ht_key.enc_key);
 
 	/* Add rule to the list of A-TCAM rules, assuming this
 	 * rule is intended to A-TCAM. In case this rule does
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_bloom_filter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_bloom_filter.c
@@ -116,9 +116,10 @@
 }
 
 static void
-mlxsw_sp_acl_bf_key_encode(struct mlxsw_sp_acl_atcam_region *aregion,
-			   struct mlxsw_sp_acl_atcam_entry *aentry,
-			   char *output, u8 *len)
+__mlxsw_sp_acl_bf_key_encode(struct mlxsw_sp_acl_atcam_region *aregion,
+			     struct mlxsw_sp_acl_atcam_entry *aentry,
+			     char *output, u8 *len, u8 max_chunks, u8 pad_bytes,
+			     u8 key_offset, u8 chunk_key_len, u8 chunk_len)
 {
 	struct mlxsw_afk_key_info *key_info = aregion->region->key_info;
 	u8 chunk_index, chunk_count, block_count;
@@ -129,17 +130,30 @@
 	chunk_count = 1 + ((block_count - 1) >> 2);
 	erp_region_id = cpu_to_be16(aentry->ht_key.erp_id |
 				   (aregion->region->id << 4));
-	for (chunk_index = MLXSW_BLOOM_KEY_CHUNKS - chunk_count;
-	     chunk_index < MLXSW_BLOOM_KEY_CHUNKS; chunk_index++) {
-		memset(chunk, 0, MLXSW_BLOOM_CHUNK_PAD_BYTES);
-		memcpy(chunk + MLXSW_BLOOM_CHUNK_PAD_BYTES, &erp_region_id,
+	for (chunk_index = max_chunks - chunk_count; chunk_index < max_chunks;
+	     chunk_index++) {
+		memset(chunk, 0, pad_bytes);
+		memcpy(chunk + pad_bytes, &erp_region_id,
 		       sizeof(erp_region_id));
-		memcpy(chunk + MLXSW_BLOOM_CHUNK_KEY_OFFSET,
-		       &aentry->enc_key[chunk_key_offsets[chunk_index]],
-		       MLXSW_BLOOM_CHUNK_KEY_BYTES);
-		chunk += MLXSW_BLOOM_KEY_CHUNK_BYTES;
+		memcpy(chunk + key_offset,
+		       &aentry->ht_key.enc_key[chunk_key_offsets[chunk_index]],
+		       chunk_key_len);
+		chunk += chunk_len;
 	}
-	*len = chunk_count * MLXSW_BLOOM_KEY_CHUNK_BYTES;
+	*len = chunk_count * chunk_len;
+}
+
+static void
+mlxsw_sp_acl_bf_key_encode(struct mlxsw_sp_acl_atcam_region *aregion,
+			   struct mlxsw_sp_acl_atcam_entry *aentry,
+			   char *output, u8 *len)
+{
+	__mlxsw_sp_acl_bf_key_encode(aregion, aentry, output, len,
+				     MLXSW_BLOOM_KEY_CHUNKS,
+				     MLXSW_BLOOM_CHUNK_PAD_BYTES,
+				     MLXSW_BLOOM_CHUNK_KEY_OFFSET,
+				     MLXSW_BLOOM_CHUNK_KEY_BYTES,
+				     MLXSW_BLOOM_KEY_CHUNK_BYTES);
 }
 
 static unsigned int
@@ -251,7 +265,7 @@
 	 * is 2^ACL_MAX_BF_LOG
 	 */
 	bf_bank_size = 1 << MLXSW_CORE_RES_GET(mlxsw_sp->core, ACL_MAX_BF_LOG);
-	bf = kzalloc(struct_size(bf, refcnt, bf_bank_size * num_erp_banks),
+	bf = kzalloc(struct_size(bf, refcnt, size_mul(bf_bank_size, num_erp_banks)),
 		     GFP_KERNEL);
 	if (!bf)
 		return ERR_PTR(-ENOMEM);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_erp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_erp.c
@@ -301,6 +301,7 @@
 			     unsigned long *p_index)
 {
 	unsigned int num_rows, entry_size;
+	unsigned long index;
 
 	/* We only allow allocations of entire rows */
 	if (num_erps % erp_core->num_erp_banks != 0)
@@ -309,10 +310,11 @@
 	entry_size = erp_core->erpt_entries_size[region_type];
 	num_rows = num_erps / erp_core->num_erp_banks;
 
-	*p_index = gen_pool_alloc(erp_core->erp_tables, num_rows * entry_size);
-	if (*p_index == 0)
+	index = gen_pool_alloc(erp_core->erp_tables, num_rows * entry_size);
+	if (!index)
 		return -ENOBUFS;
-	*p_index -= MLXSW_SP_ACL_ERP_GENALLOC_OFFSET;
+
+	*p_index = index - MLXSW_SP_ACL_ERP_GENALLOC_OFFSET;
 
 	return 0;
 }
@@ -1215,18 +1217,6 @@
 	return err ? false : true;
 }
 
-static int mlxsw_sp_acl_erp_hints_obj_cmp(const void *obj1, const void *obj2)
-{
-	const struct mlxsw_sp_acl_erp_key *key1 = obj1;
-	const struct mlxsw_sp_acl_erp_key *key2 = obj2;
-
-	/* For hints purposes, two objects are considered equal
-	 * in case the masks are the same. Does not matter what
-	 * the "ctcam" value is.
-	 */
-	return memcmp(key1->mask, key2->mask, sizeof(key1->mask));
-}
-
 static void *mlxsw_sp_acl_erp_delta_create(void *priv, void *parent_obj,
 					   void *obj)
 {
@@ -1306,7 +1296,6 @@
 static const struct objagg_ops mlxsw_sp_acl_erp_objagg_ops = {
 	.obj_size = sizeof(struct mlxsw_sp_acl_erp_key),
 	.delta_check = mlxsw_sp_acl_erp_delta_check,
-	.hints_obj_cmp = mlxsw_sp_acl_erp_hints_obj_cmp,
 	.delta_create = mlxsw_sp_acl_erp_delta_create,
 	.delta_destroy = mlxsw_sp_acl_erp_delta_destroy,
 	.root_create = mlxsw_sp_acl_erp_root_create,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c
@@ -29,70 +29,6 @@
 #define MLXSW_SP_ACL_TCAM_VREGION_REHASH_INTRVL_MIN 3000 /* ms */
 #define MLXSW_SP_ACL_TCAM_VREGION_REHASH_CREDITS 100 /* number of entries */
 
-int mlxsw_sp_acl_tcam_init(struct mlxsw_sp *mlxsw_sp,
-			   struct mlxsw_sp_acl_tcam *tcam)
-{
-	const struct mlxsw_sp_acl_tcam_ops *ops = mlxsw_sp->acl_tcam_ops;
-	u64 max_tcam_regions;
-	u64 max_regions;
-	u64 max_groups;
-	size_t alloc_size;
-	int err;
-
-	mutex_init(&tcam->lock);
-	tcam->vregion_rehash_intrvl =
-			MLXSW_SP_ACL_TCAM_VREGION_REHASH_INTRVL_DFLT;
-	INIT_LIST_HEAD(&tcam->vregion_list);
-
-	max_tcam_regions = MLXSW_CORE_RES_GET(mlxsw_sp->core,
-					      ACL_MAX_TCAM_REGIONS);
-	max_regions = MLXSW_CORE_RES_GET(mlxsw_sp->core, ACL_MAX_REGIONS);
-
-	/* Use 1:1 mapping between ACL region and TCAM region */
-	if (max_tcam_regions < max_regions)
-		max_regions = max_tcam_regions;
-
-	alloc_size = sizeof(tcam->used_regions[0]) * BITS_TO_LONGS(max_regions);
-	tcam->used_regions = kzalloc(alloc_size, GFP_KERNEL);
-	if (!tcam->used_regions)
-		return -ENOMEM;
-	tcam->max_regions = max_regions;
-
-	max_groups = MLXSW_CORE_RES_GET(mlxsw_sp->core, ACL_MAX_GROUPS);
-	alloc_size = sizeof(tcam->used_groups[0]) * BITS_TO_LONGS(max_groups);
-	tcam->used_groups = kzalloc(alloc_size, GFP_KERNEL);
-	if (!tcam->used_groups) {
-		err = -ENOMEM;
-		goto err_alloc_used_groups;
-	}
-	tcam->max_groups = max_groups;
-	tcam->max_group_size = MLXSW_CORE_RES_GET(mlxsw_sp->core,
-						 ACL_MAX_GROUP_SIZE);
-
-	err = ops->init(mlxsw_sp, tcam->priv, tcam);
-	if (err)
-		goto err_tcam_init;
-
-	return 0;
-
-err_tcam_init:
-	kfree(tcam->used_groups);
-err_alloc_used_groups:
-	kfree(tcam->used_regions);
-	return err;
-}
-
-void mlxsw_sp_acl_tcam_fini(struct mlxsw_sp *mlxsw_sp,
-			    struct mlxsw_sp_acl_tcam *tcam)
-{
-	const struct mlxsw_sp_acl_tcam_ops *ops = mlxsw_sp->acl_tcam_ops;
-
-	mutex_destroy(&tcam->lock);
-	ops->fini(mlxsw_sp, tcam->priv);
-	kfree(tcam->used_groups);
-	kfree(tcam->used_regions);
-}
-
 int mlxsw_sp_acl_tcam_priority_get(struct mlxsw_sp *mlxsw_sp,
 				   struct mlxsw_sp_acl_rule_info *rulei,
 				   u32 *priority, bool fillup_priority)
@@ -777,7 +713,9 @@
 			     rehash.dw.work);
 	int credits = MLXSW_SP_ACL_TCAM_VREGION_REHASH_CREDITS;
 
+	mutex_lock(&vregion->lock);
 	mlxsw_sp_acl_tcam_vregion_rehash(vregion->mlxsw_sp, vregion, &credits);
+	mutex_unlock(&vregion->lock);
 	if (credits < 0)
 		/* Rehash gone out of credits so it was interrupted.
 		 * Schedule the work as soon as possible to continue.
@@ -788,6 +726,17 @@
 }
 
 static void
+mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(struct mlxsw_sp_acl_tcam_rehash_ctx *ctx)
+{
+	/* The entry markers are relative to the current chunk and therefore
+	 * needs to be reset together with the chunk marker.
+	 */
+	ctx->current_vchunk = NULL;
+	ctx->start_ventry = NULL;
+	ctx->stop_ventry = NULL;
+}
+
+static void
 mlxsw_sp_acl_tcam_rehash_ctx_vchunk_changed(struct mlxsw_sp_acl_tcam_vchunk *vchunk)
 {
 	struct mlxsw_sp_acl_tcam_vregion *vregion = vchunk->vregion;
@@ -809,7 +758,7 @@
 	 * the current chunk pointer to make sure all chunks
 	 * are properly migrated.
 	 */
-	vregion->rehash.ctx.current_vchunk = NULL;
+	mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(&vregion->rehash.ctx);
 }
 
 static struct mlxsw_sp_acl_tcam_vregion *
@@ -882,10 +831,14 @@
 	struct mlxsw_sp_acl_tcam *tcam = vregion->tcam;
 
 	if (vgroup->vregion_rehash_enabled && ops->region_rehash_hints_get) {
+		struct mlxsw_sp_acl_tcam_rehash_ctx *ctx = &vregion->rehash.ctx;
+
 		mutex_lock(&tcam->lock);
 		list_del(&vregion->tlist);
 		mutex_unlock(&tcam->lock);
-		cancel_delayed_work_sync(&vregion->rehash.dw);
+		if (cancel_delayed_work_sync(&vregion->rehash.dw) &&
+		    ctx->hints_priv)
+			ops->region_rehash_hints_put(ctx->hints_priv);
 	}
 	mlxsw_sp_acl_tcam_vgroup_vregion_detach(mlxsw_sp, vregion);
 	if (vregion->region2)
@@ -1251,8 +1204,14 @@
 				      struct mlxsw_sp_acl_tcam_ventry *ventry,
 				      bool *activity)
 {
-	return mlxsw_sp_acl_tcam_entry_activity_get(mlxsw_sp,
-						    ventry->entry, activity);
+	struct mlxsw_sp_acl_tcam_vregion *vregion = ventry->vchunk->vregion;
+	int err;
+
+	mutex_lock(&vregion->lock);
+	err = mlxsw_sp_acl_tcam_entry_activity_get(mlxsw_sp, ventry->entry,
+						   activity);
+	mutex_unlock(&vregion->lock);
+	return err;
 }
 
 static int
@@ -1286,6 +1245,8 @@
 {
 	struct mlxsw_sp_acl_tcam_chunk *new_chunk;
 
+	WARN_ON(vchunk->chunk2);
+
 	new_chunk = mlxsw_sp_acl_tcam_chunk_create(mlxsw_sp, vchunk, region);
 	if (IS_ERR(new_chunk))
 		return PTR_ERR(new_chunk);
@@ -1304,7 +1265,7 @@
 {
 	mlxsw_sp_acl_tcam_chunk_destroy(mlxsw_sp, vchunk->chunk2);
 	vchunk->chunk2 = NULL;
-	ctx->current_vchunk = NULL;
+	mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(ctx);
 }
 
 static int
@@ -1327,6 +1288,9 @@
 		return 0;
 	}
 
+	if (list_empty(&vchunk->ventry_list))
+		goto out;
+
 	/* If the migration got interrupted, we have the ventry to start from
 	 * stored in context.
 	 */
@@ -1336,6 +1300,8 @@
 		ventry = list_first_entry(&vchunk->ventry_list,
 					  typeof(*ventry), list);
 
+	WARN_ON(ventry->vchunk != vchunk);
+
 	list_for_each_entry_from(ventry, &vchunk->ventry_list, list) {
 		/* During rollback, once we reach the ventry that failed
 		 * to migrate, we are done.
@@ -1376,6 +1342,7 @@
 		}
 	}
 
+out:
 	mlxsw_sp_acl_tcam_vchunk_migrate_end(mlxsw_sp, vchunk, ctx);
 	return 0;
 }
@@ -1389,6 +1356,9 @@
 	struct mlxsw_sp_acl_tcam_vchunk *vchunk;
 	int err;
 
+	if (list_empty(&vregion->vchunk_list))
+		return 0;
+
 	/* If the migration got interrupted, we have the vchunk
 	 * we are working on stored in context.
 	 */
@@ -1417,16 +1387,17 @@
 	int err, err2;
 
 	trace_mlxsw_sp_acl_tcam_vregion_migrate(mlxsw_sp, vregion);
-	mutex_lock(&vregion->lock);
 	err = mlxsw_sp_acl_tcam_vchunk_migrate_all(mlxsw_sp, vregion,
 						   ctx, credits);
 	if (err) {
+		if (ctx->this_is_rollback)
+			return err;
 		/* In case migration was not successful, we need to swap
 		 * so the original region pointer is assigned again
 		 * to vregion->region.
 		 */
 		swap(vregion->region, vregion->region2);
-		ctx->current_vchunk = NULL;
+		mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(ctx);
 		ctx->this_is_rollback = true;
 		err2 = mlxsw_sp_acl_tcam_vchunk_migrate_all(mlxsw_sp, vregion,
 							    ctx, credits);
@@ -1437,7 +1408,6 @@
 			/* Let the rollback to be continued later on. */
 		}
 	}
-	mutex_unlock(&vregion->lock);
 	trace_mlxsw_sp_acl_tcam_vregion_migrate_end(mlxsw_sp, vregion);
 	return err;
 }
@@ -1486,6 +1456,7 @@
 
 	ctx->hints_priv = hints_priv;
 	ctx->this_is_rollback = false;
+	mlxsw_sp_acl_tcam_rehash_ctx_vchunk_reset(ctx);
 
 	return 0;
 
@@ -1538,13 +1509,81 @@
 	err = mlxsw_sp_acl_tcam_vregion_migrate(mlxsw_sp, vregion,
 						ctx, credits);
 	if (err) {
-		dev_err(mlxsw_sp->bus_info->dev, "Failed to migrate vregion\n");
+		dev_err_ratelimited(mlxsw_sp->bus_info->dev, "Failed to migrate vregion\n");
+		return;
 	}
 
 	if (*credits >= 0)
 		mlxsw_sp_acl_tcam_vregion_rehash_end(mlxsw_sp, vregion, ctx);
 }
 
+int mlxsw_sp_acl_tcam_init(struct mlxsw_sp *mlxsw_sp,
+			   struct mlxsw_sp_acl_tcam *tcam)
+{
+	const struct mlxsw_sp_acl_tcam_ops *ops = mlxsw_sp->acl_tcam_ops;
+	u64 max_tcam_regions;
+	u64 max_regions;
+	u64 max_groups;
+	int err;
+
+	mutex_init(&tcam->lock);
+	tcam->vregion_rehash_intrvl =
+			MLXSW_SP_ACL_TCAM_VREGION_REHASH_INTRVL_DFLT;
+	INIT_LIST_HEAD(&tcam->vregion_list);
+
+	max_tcam_regions = MLXSW_CORE_RES_GET(mlxsw_sp->core,
+					      ACL_MAX_TCAM_REGIONS);
+	max_regions = MLXSW_CORE_RES_GET(mlxsw_sp->core, ACL_MAX_REGIONS);
+
+	/* Use 1:1 mapping between ACL region and TCAM region */
+	if (max_tcam_regions < max_regions)
+		max_regions = max_tcam_regions;
+
+	tcam->used_regions = bitmap_zalloc(max_regions, GFP_KERNEL);
+	if (!tcam->used_regions) {
+		err = -ENOMEM;
+		goto err_alloc_used_regions;
+	}
+	tcam->max_regions = max_regions;
+
+	max_groups = MLXSW_CORE_RES_GET(mlxsw_sp->core, ACL_MAX_GROUPS);
+	tcam->used_groups = bitmap_zalloc(max_groups, GFP_KERNEL);
+	if (!tcam->used_groups) {
+		err = -ENOMEM;
+		goto err_alloc_used_groups;
+	}
+	tcam->max_groups = max_groups;
+	tcam->max_group_size = MLXSW_CORE_RES_GET(mlxsw_sp->core,
+						  ACL_MAX_GROUP_SIZE);
+	tcam->max_group_size = min_t(unsigned int, tcam->max_group_size,
+				     MLXSW_REG_PAGT_ACL_MAX_NUM);
+
+	err = ops->init(mlxsw_sp, tcam->priv, tcam);
+	if (err)
+		goto err_tcam_init;
+
+	return 0;
+
+err_tcam_init:
+	bitmap_free(tcam->used_groups);
+err_alloc_used_groups:
+	bitmap_free(tcam->used_regions);
+err_alloc_used_regions:
+	mutex_destroy(&tcam->lock);
+	return err;
+}
+
+void mlxsw_sp_acl_tcam_fini(struct mlxsw_sp *mlxsw_sp,
+			    struct mlxsw_sp_acl_tcam *tcam)
+{
+	const struct mlxsw_sp_acl_tcam_ops *ops = mlxsw_sp->acl_tcam_ops;
+
+	ops->fini(mlxsw_sp, tcam->priv);
+	bitmap_free(tcam->used_groups);
+	bitmap_free(tcam->used_regions);
+	mutex_destroy(&tcam->lock);
+}
+
 static const enum mlxsw_afk_element mlxsw_sp_acl_tcam_pattern_ipv4[] = {
 	MLXSW_AFK_ELEMENT_SRC_SYS_PORT,
 	MLXSW_AFK_ELEMENT_DMAC_32_47,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.h
@@ -171,9 +171,9 @@
 };
 
 struct mlxsw_sp_acl_atcam_entry_ht_key {
-	char full_enc_key[MLXSW_REG_PTCEX_FLEX_KEY_BLOCKS_LEN]; /* Encoded
-								 * key.
-								 */
+	char enc_key[MLXSW_REG_PTCEX_FLEX_KEY_BLOCKS_LEN]; /* Encoded key, minus
+							    * delta bits.
+							    */
 	u8 erp_id;
 };
 
@@ -185,9 +185,6 @@
 	struct rhash_head ht_node;
 	struct list_head list; /* Member in entries_list */
 	struct mlxsw_sp_acl_atcam_entry_ht_key ht_key;
-	char enc_key[MLXSW_REG_PTCEX_FLEX_KEY_BLOCKS_LEN]; /* Encoded key,
-							    * minus delta bits.
-							    */
 	struct {
 		u16 start;
 		u8 mask;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_cnt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_cnt.c
@@ -122,7 +122,6 @@
 	unsigned int sub_pools_count = ARRAY_SIZE(mlxsw_sp_counter_sub_pools);
 	struct devlink *devlink = priv_to_devlink(mlxsw_sp->core);
 	struct mlxsw_sp_counter_pool *pool;
-	unsigned int map_size;
 	int err;
 
 	pool = kzalloc(struct_size(pool, sub_pools, sub_pools_count),
@@ -143,9 +142,7 @@
 	devlink_resource_occ_get_register(devlink, MLXSW_SP_RESOURCE_COUNTERS,
 					  mlxsw_sp_counter_pool_occ_get, pool);
 
-	map_size = BITS_TO_LONGS(pool->pool_size) * sizeof(unsigned long);
-
-	pool->usage = kzalloc(map_size, GFP_KERNEL);
+	pool->usage = bitmap_zalloc(pool->pool_size, GFP_KERNEL);
 	if (!pool->usage) {
 		err = -ENOMEM;
 		goto err_usage_alloc;
@@ -158,7 +155,7 @@
 	return 0;
 
 err_sub_pools_init:
-	kfree(pool->usage);
+	bitmap_free(pool->usage);
 err_usage_alloc:
 	devlink_resource_occ_get_unregister(devlink,
 					    MLXSW_SP_RESOURCE_COUNTERS);
@@ -176,7 +173,7 @@
 	WARN_ON(find_first_bit(pool->usage, pool->pool_size) !=
 			       pool->pool_size);
 	WARN_ON(atomic_read(&pool->active_entries_count));
-	kfree(pool->usage);
+	bitmap_free(pool->usage);
 	devlink_resource_occ_get_unregister(devlink,
 					    MLXSW_SP_RESOURCE_COUNTERS);
 	kfree(pool);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_cnt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_cnt.h
@@ -8,8 +8,8 @@
 #include "spectrum.h"
 
 enum mlxsw_sp_counter_sub_pool_id {
-	MLXSW_SP_COUNTER_SUB_POOL_FLOW,
 	MLXSW_SP_COUNTER_SUB_POOL_RIF,
+	MLXSW_SP_COUNTER_SUB_POOL_FLOW,
 };
 
 int mlxsw_sp_counter_alloc(struct mlxsw_sp *mlxsw_sp,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c
@@ -168,8 +168,6 @@
 static int mlxsw_sp_dcbnl_app_validate(struct net_device *dev,
 				       struct dcb_app *app)
 {
-	int prio;
-
 	if (app->priority >= IEEE_8021QAZ_MAX_TCS) {
 		netdev_err(dev, "APP entry with priority value %u is invalid\n",
 			   app->priority);
@@ -183,17 +181,6 @@
 				   app->protocol);
 			return -EINVAL;
 		}
-
-		/* Warn about any DSCP APP entries with the same PID. */
-		prio = fls(dcb_ieee_getapp_mask(dev, app));
-		if (prio--) {
-			if (prio < app->priority)
-				netdev_warn(dev, "Choosing priority %d for DSCP %d in favor of previously-active value of %d\n",
-					    app->priority, app->protocol, prio);
-			else if (prio > app->priority)
-				netdev_warn(dev, "Ignoring new priority %d for DSCP %d in favor of current value of %d\n",
-					    app->priority, app->protocol, prio);
-		}
 		break;
 
 	case IEEE_8021QAZ_APP_SEL_ETHERTYPE:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c
@@ -761,7 +761,9 @@
 	err = mlxsw_sp_get_hw_stats_by_group(&hw_stats, &len, grp);
 	if (err)
 		return;
-	mlxsw_sp_port_get_stats_raw(dev, grp, prio, ppcnt_pl);
+	err = mlxsw_sp_port_get_stats_raw(dev, grp, prio, ppcnt_pl);
+	if (err)
+		return;
 	for (i = 0; i < len; i++) {
 		data[data_index + i] = hw_stats[i].getter(ppcnt_pl);
 		if (!hw_stats[i].cells_bytes)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_nve_vxlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_nve_vxlan.c
@@ -245,8 +245,8 @@
 	.fdb_clear_offload = mlxsw_sp_nve_vxlan_clear_offload,
 };
 
-static bool mlxsw_sp2_nve_vxlan_learning_set(struct mlxsw_sp *mlxsw_sp,
-					     bool learning_en)
+static int mlxsw_sp2_nve_vxlan_learning_set(struct mlxsw_sp *mlxsw_sp,
+					    bool learning_en)
 {
 	char tnpc_pl[MLXSW_REG_TNPC_LEN];
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c
@@ -4293,6 +4293,8 @@
 	return 0;
 
 err_nexthop_neigh_init:
+	list_del(&nh->router_list_node);
+	mlxsw_sp_nexthop_counter_free(mlxsw_sp, nh);
 	mlxsw_sp_nexthop_remove(mlxsw_sp, nh);
 	return err;
 }
@@ -5194,7 +5196,7 @@
 {
 	const struct fib_nh *nh = fib_info_nh(fi, 0);
 
-	return nh->fib_nh_scope == RT_SCOPE_LINK ||
+	return nh->fib_nh_gw_family ||
 	       mlxsw_sp_nexthop4_ipip_type(mlxsw_sp, nh, NULL);
 }
 
@@ -6578,6 +6580,7 @@
 				  const struct fib6_info *rt)
 {
 	struct net_device *dev = rt->fib6_nh->fib_nh_dev;
+	int err;
 
 	nh->nhgi = nh_grp->nhgi;
 	nh->nh_weight = rt->fib6_nh->fib_nh_weight;
@@ -6593,7 +6596,16 @@
 		return 0;
 	nh->ifindex = dev->ifindex;
 
-	return mlxsw_sp_nexthop_type_init(mlxsw_sp, nh, dev);
+	err = mlxsw_sp_nexthop_type_init(mlxsw_sp, nh, dev);
+	if (err)
+		goto err_nexthop_type_init;
+
+	return 0;
+
+err_nexthop_type_init:
+	list_del(&nh->router_list_node);
+	mlxsw_sp_nexthop_counter_free(mlxsw_sp, nh);
+	return err;
 }
 
 static void mlxsw_sp_nexthop6_fini(struct mlxsw_sp *mlxsw_sp,
@@ -9576,7 +9588,7 @@
 	unsigned long *fields = config->fields;
 	u32 hash_fields;
 
-	switch (net->ipv4.sysctl_fib_multipath_hash_policy) {
+	switch (READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_policy)) {
 	case 0:
 		mlxsw_sp_mp4_hash_outer_addr(config);
 		break;
@@ -9594,7 +9606,7 @@
 		mlxsw_sp_mp_hash_inner_l3(config);
 		break;
 	case 3:
-		hash_fields = net->ipv4.sysctl_fib_multipath_hash_fields;
+		hash_fields = READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_fields);
 		/* Outer */
 		MLXSW_SP_MP_HASH_HEADER_SET(headers, IPV4_EN_NOT_TCP_NOT_UDP);
 		MLXSW_SP_MP_HASH_HEADER_SET(headers, IPV4_EN_TCP_UDP);
@@ -9775,13 +9787,14 @@
 static int __mlxsw_sp_router_init(struct mlxsw_sp *mlxsw_sp)
 {
 	struct net *net = mlxsw_sp_net(mlxsw_sp);
-	bool usp = net->ipv4.sysctl_ip_fwd_update_priority;
 	char rgcr_pl[MLXSW_REG_RGCR_LEN];
 	u64 max_rifs;
+	bool usp;
 
 	if (!MLXSW_CORE_RES_VALID(mlxsw_sp->core, MAX_RIFS))
 		return -EIO;
 	max_rifs = MLXSW_CORE_RES_GET(mlxsw_sp->core, MAX_RIFS);
+	usp = READ_ONCE(net->ipv4.sysctl_ip_fwd_update_priority);
 
 	mlxsw_reg_rgcr_pack(rgcr_pl, true, true);
 	mlxsw_reg_rgcr_max_router_interfaces_set(rgcr_pl, max_rifs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_span.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_span.c
@@ -424,7 +424,7 @@
 
 	parms = mlxsw_sp_ipip_netdev_parms4(to_dev);
 	ip_tunnel_init_flow(&fl4, parms.iph.protocol, *daddrp, *saddrp,
-			    0, 0, parms.link, tun->fwmark, 0);
+			    0, 0, dev_net(to_dev), parms.link, tun->fwmark, 0);
 
 	rt = ip_route_output_key(tun->net, &fl4);
 	if (IS_ERR(rt))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
@@ -1635,16 +1635,13 @@
 				  u16 fid)
 {
 	struct mlxsw_sp_mid *mid;
-	size_t alloc_size;
 
 	mid = kzalloc(sizeof(*mid), GFP_KERNEL);
 	if (!mid)
 		return NULL;
 
-	alloc_size = sizeof(unsigned long) *
-		     BITS_TO_LONGS(mlxsw_core_max_ports(mlxsw_sp->core));
-
-	mid->ports_in_mid = kzalloc(alloc_size, GFP_KERNEL);
+	mid->ports_in_mid = bitmap_zalloc(mlxsw_core_max_ports(mlxsw_sp->core),
+					  GFP_KERNEL);
 	if (!mid->ports_in_mid)
 		goto err_ports_in_mid_alloc;
 
@@ -1663,7 +1660,7 @@
 	return mid;
 
 err_write_mdb_entry:
-	kfree(mid->ports_in_mid);
+	bitmap_free(mid->ports_in_mid);
 err_ports_in_mid_alloc:
 	kfree(mid);
 	return NULL;
@@ -1680,7 +1677,7 @@
 			 mlxsw_core_max_ports(mlxsw_sp->core))) {
 		err = mlxsw_sp_mc_remove_mdb_entry(mlxsw_sp, mid);
 		list_del(&mid->list);
-		kfree(mid->ports_in_mid);
+		bitmap_free(mid->ports_in_mid);
 		kfree(mid);
 	}
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mellanox/mlxsw/spectrum_trap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mellanox/mlxsw/spectrum_trap.c
@@ -864,7 +864,7 @@
 		.trap = MLXSW_SP_TRAP_CONTROL(LLDP, LLDP, TRAP),
 		.listeners_arr = {
 			MLXSW_RXL(mlxsw_sp_rx_ptp_listener, LLDP, TRAP_TO_CPU,
-				  false, SP_LLDP, DISCARD),
+				  true, SP_LLDP, DISCARD),
 		},
 	},
 	{
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/Kconfig
@@ -39,6 +39,7 @@
 config KS8851_MLL
 	tristate "Micrel KS8851 MLL"
 	depends on HAS_IOMEM
+	depends on PTP_1588_CLOCK_OPTIONAL
 	select MII
 	select CRC32
 	select EEPROM_93CX6
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/ks8842.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/ks8842.c
@@ -380,7 +380,7 @@
 	}
 }
 
-static void ks8842_write_mac_addr(struct ks8842_adapter *adapter, u8 *mac)
+static void ks8842_write_mac_addr(struct ks8842_adapter *adapter, const u8 *mac)
 {
 	unsigned long flags;
 	unsigned i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/ks8851.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/ks8851.h
@@ -350,6 +350,8 @@
  * @rxd: Space for receiving SPI data, in DMA-able space.
  * @txd: Space for transmitting SPI data, in DMA-able space.
  * @msg_enable: The message flags controlling driver output (see ethtool).
+ * @tx_space: Free space in the hardware TX buffer (cached copy of KS_TXMIR).
+ * @queued_len: Space required in hardware TX buffer for queued packets in txq.
  * @fid: Incrementing frame id tag.
  * @rc_ier: Cached copy of KS_IER.
  * @rc_ccr: Cached copy of KS_CCR.
@@ -399,6 +401,7 @@
 	struct work_struct	rxctrl_work;
 
 	struct sk_buff_head	txq;
+	unsigned int		queued_len;
 
 	struct eeprom_93cx6	eeprom;
 	struct regulator	*vdd_reg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/ks8851_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/ks8851_common.c
@@ -195,7 +195,7 @@
 	struct net_device *dev = ks->netdev;
 	int ret;
 
-	ret = of_get_mac_address(np, dev->dev_addr);
+	ret = of_get_ethdev_address(np, dev);
 	if (!ret) {
 		ks8851_write_mac_addr(dev);
 		return;
@@ -361,16 +361,18 @@
 		handled |= IRQ_RXPSI;
 
 	if (status & IRQ_TXI) {
-		handled |= IRQ_TXI;
+		unsigned short tx_space = ks8851_rdreg16(ks, KS_TXMIR);
 
-		/* no lock here, tx queue should have been stopped */
+		netif_dbg(ks, intr, ks->netdev,
+			  "%s: txspace %d\n", __func__, tx_space);
 
-		/* update our idea of how much tx space is available to the
-		 * system */
-		ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR);
+		spin_lock(&ks->statelock);
+		ks->tx_space = tx_space;
+		if (netif_queue_stopped(ks->netdev))
+			netif_wake_queue(ks->netdev);
+		spin_unlock(&ks->statelock);
 
-		netif_dbg(ks, intr, ks->netdev,
-			  "%s: txspace %d\n", __func__, ks->tx_space);
+		handled |= IRQ_TXI;
 	}
 
 	if (status & IRQ_RXI)
@@ -413,9 +415,6 @@
 	if (status & IRQ_LCI)
 		mii_check_link(&ks->mii);
 
-	if (status & IRQ_TXI)
-		netif_wake_queue(ks->netdev);
-
 	return IRQ_HANDLED;
 }
 
@@ -499,6 +498,8 @@
 	ks8851_wrreg16(ks, KS_ISR, ks->rc_ier);
 	ks8851_wrreg16(ks, KS_IER, ks->rc_ier);
 
+	ks->queued_len = 0;
+	ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR);
 	netif_start_queue(ks->netdev);
 
 	netif_dbg(ks, ifup, ks->netdev, "network device up\n");
@@ -1119,7 +1120,6 @@
 	int ret;
 
 	ks->netdev = netdev;
-	ks->tx_space = 6144;
 
 	gpio = of_get_named_gpio_flags(dev->of_node, "reset-gpios", 0, NULL);
 	if (gpio == -EPROBE_DEFER)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/ks8851_par.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/ks8851_par.c
@@ -321,6 +321,8 @@
 		return ret;
 
 	netdev->irq = platform_get_irq(pdev, 0);
+	if (netdev->irq < 0)
+		return netdev->irq;
 
 	return ks8851_probe_common(netdev, dev, msg_enable);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/ks8851_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/ks8851_spi.c
@@ -287,6 +287,18 @@
 }
 
 /**
+ * calc_txlen - calculate size of message to send packet
+ * @len: Length of data
+ *
+ * Returns the size of the TXFIFO message needed to send
+ * this packet.
+ */
+static unsigned int calc_txlen(unsigned int len)
+{
+	return ALIGN(len + 4, 4);
+}
+
+/**
  * ks8851_rx_skb_spi - receive skbuff
  * @ks: The device state
  * @skb: The skbuff
@@ -305,7 +317,9 @@
  */
 static void ks8851_tx_work(struct work_struct *work)
 {
+	unsigned int dequeued_len = 0;
 	struct ks8851_net_spi *kss;
+	unsigned short tx_space;
 	struct ks8851_net *ks;
 	unsigned long flags;
 	struct sk_buff *txb;
@@ -322,6 +336,8 @@
 		last = skb_queue_empty(&ks->txq);
 
 		if (txb) {
+			dequeued_len += calc_txlen(txb->len);
+
 			ks8851_wrreg16_spi(ks, KS_RXQCR,
 					   ks->rc_rxqcr | RXQCR_SDA);
 			ks8851_wrfifo_spi(ks, txb, last);
@@ -332,6 +348,13 @@
 		}
 	}
 
+	tx_space = ks8851_rdreg16_spi(ks, KS_TXMIR);
+
+	spin_lock(&ks->statelock);
+	ks->queued_len -= dequeued_len;
+	ks->tx_space = tx_space;
+	spin_unlock(&ks->statelock);
+
 	ks8851_unlock_spi(ks, &flags);
 }
 
@@ -347,18 +370,6 @@
 }
 
 /**
- * calc_txlen - calculate size of message to send packet
- * @len: Length of data
- *
- * Returns the size of the TXFIFO message needed to send
- * this packet.
- */
-static unsigned int calc_txlen(unsigned int len)
-{
-	return ALIGN(len + 4, 4);
-}
-
-/**
  * ks8851_start_xmit_spi - transmit packet using SPI
  * @skb: The buffer to transmit
  * @dev: The device used to transmit the packet.
@@ -386,16 +397,17 @@
 
 	spin_lock(&ks->statelock);
 
-	if (needed > ks->tx_space) {
+	if (ks->queued_len + needed > ks->tx_space) {
 		netif_stop_queue(dev);
 		ret = NETDEV_TX_BUSY;
 	} else {
-		ks->tx_space -= needed;
+		ks->queued_len += needed;
 		skb_queue_tail(&ks->txq, skb);
 	}
 
 	spin_unlock(&ks->statelock);
-	schedule_work(&kss->tx_work);
+	if (ret == NETDEV_TX_OK)
+		schedule_work(&kss->tx_work);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/micrel/ksz884x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/micrel/ksz884x.c
@@ -4033,7 +4033,7 @@
 	}
 }
 
-static int hw_add_addr(struct ksz_hw *hw, u8 *mac_addr)
+static int hw_add_addr(struct ksz_hw *hw, const u8 *mac_addr)
 {
 	int i;
 	int j = ADDITIONAL_ENTRIES;
@@ -4054,7 +4054,7 @@
 	return -1;
 }
 
-static int hw_del_addr(struct ksz_hw *hw, u8 *mac_addr)
+static int hw_del_addr(struct ksz_hw *hw, const u8 *mac_addr)
 {
 	int i;
 
@@ -6848,7 +6848,7 @@
 	char banner[sizeof(version)];
 	struct ksz_switch *sw = NULL;
 
-	result = pci_enable_device(pdev);
+	result = pcim_enable_device(pdev);
 	if (result)
 		return result;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/enc28j60.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/enc28j60.c
@@ -517,7 +517,7 @@
 	if (!is_valid_ether_addr(address->sa_data))
 		return -EADDRNOTAVAIL;
 
-	ether_addr_copy(dev->dev_addr, address->sa_data);
+	eth_hw_addr_set(dev, address->sa_data);
 	return enc28j60_set_hw_macaddr(dev);
 }
 
@@ -1573,7 +1573,7 @@
 	}
 
 	if (device_get_mac_address(&spi->dev, macaddr, sizeof(macaddr)))
-		ether_addr_copy(dev->dev_addr, macaddr);
+		eth_hw_addr_set(dev, macaddr);
 	else
 		eth_hw_addr_random(dev);
 	enc28j60_set_hw_macaddr(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/encx24j600-regmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/encx24j600-regmap.c
@@ -359,7 +359,7 @@
 		goto err_out;
 
 	usleep_range(26, 100);
-	while ((ret = regmap_read(ctx->regmap, MISTAT, &mistat) != 0) &&
+	while (((ret = regmap_read(ctx->regmap, MISTAT, &mistat)) == 0) &&
 	       (mistat & BUSY))
 		cpu_relax();
 
@@ -397,7 +397,7 @@
 		goto err_out;
 
 	usleep_range(26, 100);
-	while ((ret = regmap_read(ctx->regmap, MISTAT, &mistat) != 0) &&
+	while (((ret = regmap_read(ctx->regmap, MISTAT, &mistat)) == 0) &&
 	       (mistat & BUSY))
 		cpu_relax();
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/lan743x_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/lan743x_main.c
@@ -83,6 +83,18 @@
 				  !(data & HW_CFG_LRST_), 100000, 10000000);
 }
 
+static int lan743x_csr_wait_for_bit_atomic(struct lan743x_adapter *adapter,
+					   int offset, u32 bit_mask,
+					   int target_value, int udelay_min,
+					   int udelay_max, int count)
+{
+	u32 data;
+
+	return readx_poll_timeout_atomic(LAN743X_CSR_READ_OP, offset, data,
+					 target_value == !!(data & bit_mask),
+					 udelay_max, udelay_min * count);
+}
+
 static int lan743x_csr_wait_for_bit(struct lan743x_adapter *adapter,
 				    int offset, u32 bit_mask,
 				    int target_value, int usleep_min,
@@ -671,8 +683,8 @@
 	u32 dp_sel;
 	int i;
 
-	if (lan743x_csr_wait_for_bit(adapter, DP_SEL, DP_SEL_DPRDY_,
-				     1, 40, 100, 100))
+	if (lan743x_csr_wait_for_bit_atomic(adapter, DP_SEL, DP_SEL_DPRDY_,
+					    1, 40, 100, 100))
 		return -EIO;
 	dp_sel = lan743x_csr_read(adapter, DP_SEL);
 	dp_sel &= ~DP_SEL_MASK_;
@@ -683,8 +695,9 @@
 		lan743x_csr_write(adapter, DP_ADDR, addr + i);
 		lan743x_csr_write(adapter, DP_DATA_0, buf[i]);
 		lan743x_csr_write(adapter, DP_CMD, DP_CMD_WRITE_);
-		if (lan743x_csr_wait_for_bit(adapter, DP_SEL, DP_SEL_DPRDY_,
-					     1, 40, 100, 100))
+		if (lan743x_csr_wait_for_bit_atomic(adapter, DP_SEL,
+						    DP_SEL_DPRDY_,
+						    1, 40, 100, 100))
 			return -EIO;
 	}
 
@@ -816,7 +829,7 @@
 			eth_random_addr(adapter->mac_address);
 	}
 	lan743x_mac_set_address(adapter, adapter->mac_address);
-	ether_addr_copy(netdev->dev_addr, adapter->mac_address);
+	eth_hw_addr_set(netdev, adapter->mac_address);
 
 	return 0;
 }
@@ -914,8 +927,7 @@
 }
 
 static void lan743x_phy_update_flowcontrol(struct lan743x_adapter *adapter,
-					   u8 duplex, u16 local_adv,
-					   u16 remote_adv)
+					   u16 local_adv, u16 remote_adv)
 {
 	struct lan743x_phy *phy = &adapter->phy;
 	u8 cap;
@@ -943,7 +955,6 @@
 
 	phy_print_status(phydev);
 	if (phydev->state == PHY_RUNNING) {
-		struct ethtool_link_ksettings ksettings;
 		int remote_advertisement = 0;
 		int local_advertisement = 0;
 
@@ -980,18 +991,14 @@
 		}
 		lan743x_csr_write(adapter, MAC_CR, data);
 
-		memset(&ksettings, 0, sizeof(ksettings));
-		phy_ethtool_get_link_ksettings(netdev, &ksettings);
 		local_advertisement =
 			linkmode_adv_to_mii_adv_t(phydev->advertising);
 		remote_advertisement =
 			linkmode_adv_to_mii_adv_t(phydev->lp_advertising);
 
-		lan743x_phy_update_flowcontrol(adapter,
-					       ksettings.base.duplex,
-					       local_advertisement,
+		lan743x_phy_update_flowcontrol(adapter, local_advertisement,
 					       remote_advertisement);
-		lan743x_ptp_update_latency(adapter, ksettings.base.speed);
+		lan743x_ptp_update_latency(adapter, phydev->speed);
 	}
 }
 
@@ -2670,7 +2677,7 @@
 	ret = eth_prepare_mac_addr_change(netdev, sock_addr);
 	if (ret)
 		return ret;
-	ether_addr_copy(netdev->dev_addr, sock_addr->sa_data);
+	eth_hw_addr_set(netdev, sock_addr->sa_data);
 	lan743x_mac_set_address(adapter, sock_addr->sa_data);
 	lan743x_rfe_update_mac_address(adapter);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/Kconfig
@@ -4,6 +4,8 @@
 	depends on HAS_IOMEM
 	depends on OF
 	depends on ARCH_SPARX5 || COMPILE_TEST
+	depends on PTP_1588_CLOCK_OPTIONAL
+	depends on BRIDGE || BRIDGE=n
 	select PHYLINK
 	select PHY_SPARX5_SERDES
 	select RESET_CONTROLLER
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_ethtool.c
@@ -1103,7 +1103,7 @@
 	stats->tx_carrier_errors = portstats[spx5_stats_tx_csense_cnt];
 	stats->tx_window_errors = portstats[spx5_stats_tx_late_coll_cnt];
 	stats->rx_dropped = portstats[spx5_stats_ana_ac_port_stat_lsb_cnt];
-	for (idx = 0; idx < 2 * SPX5_PRIOS; ++idx, ++stats)
+	for (idx = 0; idx < 2 * SPX5_PRIOS; ++idx)
 		stats->rx_dropped += portstats[spx5_stats_green_p0_rx_port_drop
 					       + idx];
 	stats->tx_dropped = portstats[spx5_stats_tx_local_drop];
@@ -1219,6 +1219,9 @@
 	snprintf(queue_name, sizeof(queue_name), "%s-stats",
 		 dev_name(sparx5->dev));
 	sparx5->stats_queue = create_singlethread_workqueue(queue_name);
+	if (!sparx5->stats_queue)
+		return -ENOMEM;
+
 	INIT_DELAYED_WORK(&sparx5->stats_work, sparx5_check_stats_work);
 	queue_delayed_work(sparx5->stats_queue, &sparx5->stats_work,
 			   SPX5_STATS_CHECK_DELAY);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c
@@ -420,6 +420,8 @@
 			db_hw->dataptr = phys;
 			db_hw->status = 0;
 			db = devm_kzalloc(sparx5->dev, sizeof(*db), GFP_KERNEL);
+			if (!db)
+				return -ENOMEM;
 			db->cpu_addr = cpu_addr;
 			list_add_tail(&db->list, &tx->db_list);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c
@@ -344,10 +344,10 @@
 				 list) {
 		if ((vid == 0 || mact_entry->vid == vid) &&
 		    ether_addr_equal(addr, mact_entry->mac)) {
+			sparx5_mact_forget(sparx5, addr, mact_entry->vid);
+
 			list_del(&mact_entry->list);
 			devm_kfree(sparx5->dev, mact_entry);
-
-			sparx5_mact_forget(sparx5, addr, mact_entry->vid);
 		}
 	}
 	mutex_unlock(&sparx5->mact_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
@@ -629,6 +629,9 @@
 	snprintf(queue_name, sizeof(queue_name), "%s-mact",
 		 dev_name(sparx5->dev));
 	sparx5->mact_queue = create_singlethread_workqueue(queue_name);
+	if (!sparx5->mact_queue)
+		return -ENOMEM;
+
 	INIT_DELAYED_WORK(&sparx5->mact_work, sparx5_mact_pull_work);
 	queue_delayed_work(sparx5->mact_queue, &sparx5->mact_work,
 			   SPX5_MACT_PULL_DELAY);
@@ -644,12 +647,11 @@
 	err = -ENXIO;
 	if (sparx5->fdma_irq >= 0) {
 		if (GCB_CHIP_ID_REV_ID_GET(sparx5->chip_id) > 0)
-			err = devm_request_threaded_irq(sparx5->dev,
-							sparx5->fdma_irq,
-							NULL,
-							sparx5_fdma_handler,
-							IRQF_ONESHOT,
-							"sparx5-fdma", sparx5);
+			err = devm_request_irq(sparx5->dev,
+					       sparx5->fdma_irq,
+					       sparx5_fdma_handler,
+					       0,
+					       "sparx5-fdma", sparx5);
 		if (!err)
 			err = sparx5_fdma_start(sparx5);
 		if (err)
@@ -776,7 +778,7 @@
 	if (err)
 		goto cleanup_config;
 
-	if (!of_get_mac_address(np, sparx5->base_mac)) {
+	if (of_get_mac_address(np, sparx5->base_mac)) {
 		dev_info(sparx5->dev, "MAC addr was not set, use random MAC\n");
 		eth_random_addr(sparx5->base_mac);
 		sparx5->base_mac[5] = 0;
@@ -826,6 +828,8 @@
 
 cleanup_ports:
 	sparx5_cleanup_ports(sparx5);
+	if (sparx5->mact_queue)
+		destroy_workqueue(sparx5->mact_queue);
 cleanup_config:
 	kfree(configs);
 cleanup_pnode:
@@ -849,6 +853,7 @@
 	sparx5_cleanup_ports(sparx5);
 	/* Unregister netdevs */
 	sparx5_unregister_notifier_blocks(sparx5);
+	destroy_workqueue(sparx5->mact_queue);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c
@@ -83,7 +83,7 @@
 	err = phylink_of_phy_connect(port->phylink, port->of_node, 0);
 	if (err) {
 		netdev_err(ndev, "Could not attach to PHY\n");
-		return err;
+		goto err_connect;
 	}
 
 	phylink_start(port->phylink);
@@ -95,10 +95,20 @@
 			err = sparx5_serdes_set(port->sparx5, port, &port->conf);
 		else
 			err = phy_power_on(port->serdes);
-		if (err)
+		if (err) {
 			netdev_err(ndev, "%s failed\n", __func__);
+			goto out_power;
+		}
 	}
 
+	return 0;
+
+out_power:
+	phylink_stop(port->phylink);
+	phylink_disconnect_phy(port->phylink);
+err_connect:
+	sparx5_port_enable(port, false);
+
 	return err;
 }
 
@@ -162,7 +172,7 @@
 	sparx5_mact_learn(sparx5, PGID_CPU, addr->sa_data, port->pvid);
 
 	/* Record the address */
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_packet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_packet.c
@@ -107,6 +107,8 @@
 			/* This assumes STATUS_WORD_POS == 1, Status
 			 * just after last data
 			 */
+			if (!byte_swap)
+				val = ntohl((__force __be32)val);
 			byte_cnt -= (4 - XTR_VALID_BYTES(val));
 			eof_flag = true;
 			break;
@@ -145,9 +147,9 @@
 	skb_put(skb, byte_cnt - ETH_FCS_LEN);
 	eth_skb_pad(skb);
 	skb->protocol = eth_type_trans(skb, netdev);
-	netif_rx(skb);
 	netdev->stats.rx_bytes += skb->len;
 	netdev->stats.rx_packets++;
+	netif_rx(skb);
 }
 
 static int sparx5_inject(struct sparx5 *sparx5,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -730,7 +730,7 @@
 	bool sgmii = false, inband_aneg = false;
 	int err;
 
-	if (port->conf.inband) {
+	if (conf->inband) {
 		if (conf->portmode == PHY_INTERFACE_MODE_SGMII ||
 		    conf->portmode == PHY_INTERFACE_MODE_QSGMII)
 			inband_aneg = true; /* Cisco-SGMII in-band-aneg */
@@ -947,7 +947,7 @@
 	if (err)
 		return -EINVAL;
 
-	if (port->conf.inband) {
+	if (conf->inband) {
 		/* Enable/disable 1G counters in ASM */
 		spx5_rmw(ASM_PORT_CFG_CSC_STAT_DIS_SET(high_speed_dev),
 			 ASM_PORT_CFG_CSC_STAT_DIS,
@@ -1113,7 +1113,7 @@
 	spx5_inst_rmw(DEV10G_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
 		      DEV10G_MAC_MAXLEN_CFG_MAX_LEN,
 		      devinst,
-		      DEV10G_MAC_ENA_CFG(0));
+		      DEV10G_MAC_MAXLEN_CFG(0));
 
 	/* Handle Signal Detect in 10G PCS */
 	spx5_inst_wr(PCS10G_BR_PCS_SD_CFG_SD_POL_SET(sd_pol) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c
@@ -58,16 +58,6 @@
 	struct sparx5 *sparx5 = port->sparx5;
 	int ret;
 
-	/* Make the port a member of the VLAN */
-	set_bit(port->portno, sparx5->vlan_mask[vid]);
-	ret = sparx5_vlant_set_mask(sparx5, vid);
-	if (ret)
-		return ret;
-
-	/* Default ingress vlan classification */
-	if (pvid)
-		port->pvid = vid;
-
 	/* Untagged egress vlan classification */
 	if (untagged && port->vid != vid) {
 		if (port->vid) {
@@ -79,6 +69,16 @@
 		port->vid = vid;
 	}
 
+	/* Make the port a member of the VLAN */
+	set_bit(port->portno, sparx5->vlan_mask[vid]);
+	ret = sparx5_vlant_set_mask(sparx5, vid);
+	if (ret)
+		return ret;
+
+	/* Default ingress vlan classification */
+	if (pvid)
+		port->pvid = vid;
+
 	sparx5_vlan_port_apply(sparx5, port);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microsoft/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microsoft/Kconfig
@@ -19,6 +19,7 @@
 	tristate "Microsoft Azure Network Adapter (MANA) support"
 	depends on PCI_MSI && X86_64
 	depends on PCI_HYPERV
+	select PAGE_POOL
 	help
 	  This driver supports Microsoft Azure Network Adapter (MANA).
 	  So far, the driver is only supported on X86_64.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microsoft/mana/gdma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microsoft/mana/gdma.h
@@ -324,9 +324,12 @@
 	};
 };
 
+#define MANA_IRQ_NAME_SZ 32
+
 struct gdma_irq_context {
 	void (*handler)(void *arg);
 	void *arg;
+	char name[MANA_IRQ_NAME_SZ];
 };
 
 struct gdma_context {
@@ -488,7 +491,14 @@
 
 #define GDMA_DRV_CAP_FLAG_1_EQ_SHARING_MULTI_VPORT BIT(0)
 
-#define GDMA_DRV_CAP_FLAGS1 GDMA_DRV_CAP_FLAG_1_EQ_SHARING_MULTI_VPORT
+/* Advertise to the NIC firmware: the NAPI work_done variable race is fixed,
+ * so the driver is able to reliably support features like busy_poll.
+ */
+#define GDMA_DRV_CAP_FLAG_1_NAPI_WKDONE_FIX BIT(2)
+
+#define GDMA_DRV_CAP_FLAGS1 \
+	(GDMA_DRV_CAP_FLAG_1_EQ_SHARING_MULTI_VPORT | \
+	 GDMA_DRV_CAP_FLAG_1_NAPI_WKDONE_FIX)
 
 #define GDMA_DRV_CAP_FLAGS2 0
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microsoft/mana/gdma_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microsoft/mana/gdma_main.c
@@ -368,6 +368,11 @@
 			break;
 		}
 
+		/* Per GDMA spec, rmb is necessary after checking owner_bits, before
+		 * reading eqe.
+		 */
+		rmb();
+
 		mana_gd_process_eqe(eq);
 
 		eq->head++;
@@ -1096,6 +1101,11 @@
 	if (WARN_ON_ONCE(owner_bits != new_bits))
 		return -1;
 
+	/* Per GDMA spec, rmb is necessary after checking owner_bits, before
+	 * reading completion info
+	 */
+	rmb();
+
 	comp->wq_num = cqe->cqe_info.wq_num;
 	comp->is_sq = cqe->cqe_info.is_sq;
 	memcpy(comp->cqe_data, cqe->cqe_data, GDMA_COMP_DATA_SIZE);
@@ -1185,13 +1195,20 @@
 		gic->handler = NULL;
 		gic->arg = NULL;
 
+		if (!i)
+			snprintf(gic->name, MANA_IRQ_NAME_SZ, "mana_hwc@pci:%s",
+				 pci_name(pdev));
+		else
+			snprintf(gic->name, MANA_IRQ_NAME_SZ, "mana_q%d@pci:%s",
+				 i - 1, pci_name(pdev));
+
 		irq = pci_irq_vector(pdev, i);
 		if (irq < 0) {
 			err = irq;
 			goto free_irq;
 		}
 
-		err = request_irq(irq, mana_gd_intr, 0, "mana_intr", gic);
+		err = request_irq(irq, mana_gd_intr, 0, gic->name, gic);
 		if (err)
 			goto free_irq;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microsoft/mana/hw_channel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microsoft/mana/hw_channel.c
@@ -51,9 +51,33 @@
 	return 0;
 }
 
+static int mana_hwc_post_rx_wqe(const struct hwc_wq *hwc_rxq,
+				struct hwc_work_request *req)
+{
+	struct device *dev = hwc_rxq->hwc->dev;
+	struct gdma_sge *sge;
+	int err;
+
+	sge = &req->sge;
+	sge->address = (u64)req->buf_sge_addr;
+	sge->mem_key = hwc_rxq->msg_buf->gpa_mkey;
+	sge->size = req->buf_len;
+
+	memset(&req->wqe_req, 0, sizeof(struct gdma_wqe_request));
+	req->wqe_req.sgl = sge;
+	req->wqe_req.num_sge = 1;
+	req->wqe_req.client_data_unit = 0;
+
+	err = mana_gd_post_and_ring(hwc_rxq->gdma_wq, &req->wqe_req, NULL);
+	if (err)
+		dev_err(dev, "Failed to post WQE on HWC RQ: %d\n", err);
+	return err;
+}
+
 static void mana_hwc_handle_resp(struct hw_channel_context *hwc, u32 resp_len,
-				 const struct gdma_resp_hdr *resp_msg)
+				 struct hwc_work_request *rx_req)
 {
+	const struct gdma_resp_hdr *resp_msg = rx_req->buf_va;
 	struct hwc_caller_ctx *ctx;
 	int err;
 
@@ -61,6 +85,7 @@
 		      hwc->inflight_msg_res.map)) {
 		dev_err(hwc->dev, "hwc_rx: invalid msg_id = %u\n",
 			resp_msg->response.hwc_msg_id);
+		mana_hwc_post_rx_wqe(hwc->rxq, rx_req);
 		return;
 	}
 
@@ -74,30 +99,13 @@
 	memcpy(ctx->output_buf, resp_msg, resp_len);
 out:
 	ctx->error = err;
-	complete(&ctx->comp_event);
-}
-
-static int mana_hwc_post_rx_wqe(const struct hwc_wq *hwc_rxq,
-				struct hwc_work_request *req)
-{
-	struct device *dev = hwc_rxq->hwc->dev;
-	struct gdma_sge *sge;
-	int err;
-
-	sge = &req->sge;
-	sge->address = (u64)req->buf_sge_addr;
-	sge->mem_key = hwc_rxq->msg_buf->gpa_mkey;
-	sge->size = req->buf_len;
 
-	memset(&req->wqe_req, 0, sizeof(struct gdma_wqe_request));
-	req->wqe_req.sgl = sge;
-	req->wqe_req.num_sge = 1;
-	req->wqe_req.client_data_unit = 0;
+	/* Must post rx wqe before complete(), otherwise the next rx may
+	 * hit no_wqe error.
+	 */
+	mana_hwc_post_rx_wqe(hwc->rxq, rx_req);
 
-	err = mana_gd_post_and_ring(hwc_rxq->gdma_wq, &req->wqe_req, NULL);
-	if (err)
-		dev_err(dev, "Failed to post WQE on HWC RQ: %d\n", err);
-	return err;
+	complete(&ctx->comp_event);
 }
 
 static void mana_hwc_init_event_handler(void *ctx, struct gdma_queue *q_self,
@@ -208,14 +216,12 @@
 		return;
 	}
 
-	mana_hwc_handle_resp(hwc, rx_oob->tx_oob_data_size, resp);
+	mana_hwc_handle_resp(hwc, rx_oob->tx_oob_data_size, rx_req);
 
-	/* Do no longer use 'resp', because the buffer is posted to the HW
-	 * in the below mana_hwc_post_rx_wqe().
+	/* Can no longer use 'resp', because the buffer is posted to the HW
+	 * in mana_hwc_handle_resp() above.
 	 */
 	resp = NULL;
-
-	mana_hwc_post_rx_wqe(hwc_rxq, rx_req);
 }
 
 static void mana_hwc_tx_event_handler(void *ctx, u32 gdma_txq_id,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microsoft/mana/mana.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microsoft/mana/mana.h
@@ -77,6 +77,8 @@
 	atomic_t pending_sends;
 
 	struct mana_stats stats;
+
+	bool napi_initialized;
 };
 
 /* skb data and frags dma mappings */
@@ -252,6 +254,7 @@
 	/* NAPI data */
 	struct napi_struct napi;
 	int work_done;
+	int work_done_since_doorbell;
 	int budget;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/microsoft/mana/mana_en.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/microsoft/mana/mana_en.c
@@ -828,17 +828,21 @@
 		case CQE_TX_VPORT_IDX_OUT_OF_RANGE:
 		case CQE_TX_VPORT_DISABLED:
 		case CQE_TX_VLAN_TAGGING_VIOLATION:
-			WARN_ONCE(1, "TX: CQE error %d: ignored.\n",
-				  cqe_oob->cqe_hdr.cqe_type);
+			if (net_ratelimit())
+				netdev_err(ndev, "TX: CQE error %d\n",
+					   cqe_oob->cqe_hdr.cqe_type);
+
 			break;
 
 		default:
-			/* If the CQE type is unexpected, log an error, assert,
-			 * and go through the error path.
+			/* If the CQE type is unknown, log an error,
+			 * and still free the SKB, update tail, etc.
 			 */
-			WARN_ONCE(1, "TX: Unexpected CQE type %d: HW BUG?\n",
-				  cqe_oob->cqe_hdr.cqe_type);
-			return;
+			if (net_ratelimit())
+				netdev_err(ndev, "TX: unknown CQE type %d\n",
+					   cqe_oob->cqe_hdr.cqe_type);
+
+			break;
 		}
 
 		if (WARN_ON_ONCE(txq->gdma_txq_id != completions[i].wq_num))
@@ -980,8 +984,10 @@
 		break;
 
 	case CQE_RX_TRUNCATED:
-		netdev_err(ndev, "Dropped a truncated packet\n");
-		return;
+		++ndev->stats.rx_dropped;
+		rxbuf_oob = &rxq->rx_oobs[rxq->buf_index];
+		netdev_warn_once(ndev, "Dropped a truncated packet\n");
+		goto drop;
 
 	case CQE_RX_COALESCED_4:
 		netdev_err(ndev, "RX coalescing is unsupported\n");
@@ -1043,6 +1049,7 @@
 
 	mana_rx_skb(old_buf, oob, rxq);
 
+drop:
 	mana_move_wq_tail(rxq->gdma_rq, rxbuf_oob->wqe_inf.wqe_size_in_bu);
 
 	mana_post_pkt_rxq(rxq);
@@ -1068,10 +1075,10 @@
 	}
 }
 
-static void mana_cq_handler(void *context, struct gdma_queue *gdma_queue)
+static int mana_cq_handler(void *context, struct gdma_queue *gdma_queue)
 {
 	struct mana_cq *cq = context;
-	u8 arm_bit;
+	int w;
 
 	WARN_ON_ONCE(cq->gdma_cq != gdma_queue);
 
@@ -1080,26 +1087,38 @@
 	else
 		mana_poll_tx_cq(cq);
 
-	if (cq->work_done < cq->budget &&
-	    napi_complete_done(&cq->napi, cq->work_done)) {
-		arm_bit = SET_ARM_BIT;
-	} else {
-		arm_bit = 0;
+	w = cq->work_done;
+	cq->work_done_since_doorbell += w;
+
+	if (w < cq->budget) {
+		mana_gd_ring_cq(gdma_queue, SET_ARM_BIT);
+		cq->work_done_since_doorbell = 0;
+		napi_complete_done(&cq->napi, w);
+	} else if (cq->work_done_since_doorbell >
+		   cq->gdma_cq->queue_size / COMP_ENTRY_SIZE * 4) {
+		/* MANA hardware requires at least one doorbell ring every 8
+		 * wraparounds of CQ even if there is no need to arm the CQ.
+		 * This driver rings the doorbell as soon as we have exceeded
+		 * 4 wraparounds.
+		 */
+		mana_gd_ring_cq(gdma_queue, 0);
+		cq->work_done_since_doorbell = 0;
 	}
 
-	mana_gd_ring_cq(gdma_queue, arm_bit);
+	return w;
 }
 
 static int mana_poll(struct napi_struct *napi, int budget)
 {
 	struct mana_cq *cq = container_of(napi, struct mana_cq, napi);
+	int w;
 
 	cq->work_done = 0;
 	cq->budget = budget;
 
-	mana_cq_handler(cq, cq->gdma_cq);
+	w = mana_cq_handler(cq, cq->gdma_cq);
 
-	return min(cq->work_done, budget);
+	return min(w, budget);
 }
 
 static void mana_schedule_napi(void *context, struct gdma_queue *gdma_queue)
@@ -1139,10 +1158,12 @@
 
 	for (i = 0; i < apc->num_queues; i++) {
 		napi = &apc->tx_qp[i].tx_cq.napi;
-		napi_synchronize(napi);
-		napi_disable(napi);
-		netif_napi_del(napi);
-
+		if (apc->tx_qp[i].txq.napi_initialized) {
+			napi_synchronize(napi);
+			napi_disable(napi);
+			netif_napi_del(napi);
+			apc->tx_qp[i].txq.napi_initialized = false;
+		}
 		mana_destroy_wq_obj(apc, GDMA_SQ, apc->tx_qp[i].tx_object);
 
 		mana_deinit_cq(apc, &apc->tx_qp[i].tx_cq);
@@ -1198,6 +1219,7 @@
 		txq->ndev = net;
 		txq->net_txq = netdev_get_tx_queue(net, i);
 		txq->vp_offset = apc->tx_vp_offset;
+		txq->napi_initialized = false;
 		skb_queue_head_init(&txq->pending_skbs);
 
 		memset(&spec, 0, sizeof(spec));
@@ -1262,6 +1284,7 @@
 
 		netif_tx_napi_add(net, &cq->napi, mana_poll, NAPI_POLL_WEIGHT);
 		napi_enable(&cq->napi);
+		txq->napi_initialized = true;
 
 		mana_gd_ring_cq(cq->gdma_cq, SET_ARM_BIT);
 	}
@@ -1273,7 +1296,7 @@
 }
 
 static void mana_destroy_rxq(struct mana_port_context *apc,
-			     struct mana_rxq *rxq, bool validate_state)
+			     struct mana_rxq *rxq, bool napi_initialized)
 
 {
 	struct gdma_context *gc = apc->ac->gdma_dev->gdma_context;
@@ -1287,11 +1310,13 @@
 
 	napi = &rxq->rx_cq.napi;
 
-	if (validate_state)
+	if (napi_initialized) {
 		napi_synchronize(napi);
 
-	napi_disable(napi);
-	netif_napi_del(napi);
+		napi_disable(napi);
+
+		netif_napi_del(napi);
+	}
 
 	mana_destroy_wq_obj(apc, GDMA_RQ, rxq->rxobj);
 
@@ -1610,7 +1635,7 @@
 	if (apc->num_queues > apc->max_queues)
 		apc->num_queues = apc->max_queues;
 
-	ether_addr_copy(ndev->dev_addr, apc->mac_addr);
+	eth_hw_addr_set(ndev, apc->mac_addr);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/moxa/moxart_ether.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/moxa/moxart_ether.c
@@ -74,11 +74,6 @@
 static void moxart_mac_free_memory(struct net_device *ndev)
 {
 	struct moxart_mac_priv_t *priv = netdev_priv(ndev);
-	int i;
-
-	for (i = 0; i < RX_DESC_NUM; i++)
-		dma_unmap_single(&ndev->dev, priv->rx_mapping[i],
-				 priv->rx_buf_size, DMA_FROM_DEVICE);
 
 	if (priv->tx_desc_base)
 		dma_free_coherent(&priv->pdev->dev,
@@ -147,11 +142,11 @@
 		       desc + RX_REG_OFFSET_DESC1);
 
 		priv->rx_buf[i] = priv->rx_buf_base + priv->rx_buf_size * i;
-		priv->rx_mapping[i] = dma_map_single(&ndev->dev,
+		priv->rx_mapping[i] = dma_map_single(&priv->pdev->dev,
 						     priv->rx_buf[i],
 						     priv->rx_buf_size,
 						     DMA_FROM_DEVICE);
-		if (dma_mapping_error(&ndev->dev, priv->rx_mapping[i]))
+		if (dma_mapping_error(&priv->pdev->dev, priv->rx_mapping[i]))
 			netdev_err(ndev, "DMA mapping error\n");
 
 		moxart_desc_write(priv->rx_mapping[i],
@@ -193,6 +188,7 @@
 static int moxart_mac_stop(struct net_device *ndev)
 {
 	struct moxart_mac_priv_t *priv = netdev_priv(ndev);
+	int i;
 
 	napi_disable(&priv->napi);
 
@@ -204,6 +200,11 @@
 	/* disable all functions */
 	writel(0, priv->base + REG_MAC_CTRL);
 
+	/* unmap areas mapped in moxart_mac_setup_desc_ring() */
+	for (i = 0; i < RX_DESC_NUM; i++)
+		dma_unmap_single(&priv->pdev->dev, priv->rx_mapping[i],
+				 priv->rx_buf_size, DMA_FROM_DEVICE);
+
 	return 0;
 }
 
@@ -240,7 +241,7 @@
 		if (len > RX_BUF_SIZE)
 			len = RX_BUF_SIZE;
 
-		dma_sync_single_for_cpu(&ndev->dev,
+		dma_sync_single_for_cpu(&priv->pdev->dev,
 					priv->rx_mapping[rx_head],
 					priv->rx_buf_size, DMA_FROM_DEVICE);
 		skb = netdev_alloc_skb_ip_align(ndev, len);
@@ -294,7 +295,7 @@
 	unsigned int tx_tail = priv->tx_tail;
 
 	while (tx_tail != tx_head) {
-		dma_unmap_single(&ndev->dev, priv->tx_mapping[tx_tail],
+		dma_unmap_single(&priv->pdev->dev, priv->tx_mapping[tx_tail],
 				 priv->tx_len[tx_tail], DMA_TO_DEVICE);
 
 		ndev->stats.tx_packets++;
@@ -358,9 +359,9 @@
 
 	len = skb->len > TX_BUF_SIZE ? TX_BUF_SIZE : skb->len;
 
-	priv->tx_mapping[tx_head] = dma_map_single(&ndev->dev, skb->data,
+	priv->tx_mapping[tx_head] = dma_map_single(&priv->pdev->dev, skb->data,
 						   len, DMA_TO_DEVICE);
-	if (dma_mapping_error(&ndev->dev, priv->tx_mapping[tx_head])) {
+	if (dma_mapping_error(&priv->pdev->dev, priv->tx_mapping[tx_head])) {
 		netdev_err(ndev, "DMA mapping error\n");
 		goto out_unlock;
 	}
@@ -379,7 +380,7 @@
 		len = ETH_ZLEN;
 	}
 
-	dma_sync_single_for_device(&ndev->dev, priv->tx_mapping[tx_head],
+	dma_sync_single_for_device(&priv->pdev->dev, priv->tx_mapping[tx_head],
 				   priv->tx_buf_size, DMA_TO_DEVICE);
 
 	txdes1 = TX_DESC1_LTS | TX_DESC1_FTS | (len & TX_DESC1_BUF_SIZE_MASK);
@@ -493,7 +494,7 @@
 	priv->tx_buf_size = TX_BUF_SIZE;
 	priv->rx_buf_size = RX_BUF_SIZE;
 
-	priv->tx_desc_base = dma_alloc_coherent(&pdev->dev, TX_REG_DESC_SIZE *
+	priv->tx_desc_base = dma_alloc_coherent(p_dev, TX_REG_DESC_SIZE *
 						TX_DESC_NUM, &priv->tx_base,
 						GFP_DMA | GFP_KERNEL);
 	if (!priv->tx_desc_base) {
@@ -501,7 +502,7 @@
 		goto init_fail;
 	}
 
-	priv->rx_desc_base = dma_alloc_coherent(&pdev->dev, RX_REG_DESC_SIZE *
+	priv->rx_desc_base = dma_alloc_coherent(p_dev, RX_REG_DESC_SIZE *
 						RX_DESC_NUM, &priv->rx_base,
 						GFP_DMA | GFP_KERNEL);
 	if (!priv->rx_desc_base) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mscc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mscc/Kconfig
@@ -28,7 +28,7 @@
 	depends on BRIDGE || BRIDGE=n
 	depends on NET_SWITCHDEV
 	depends on HAS_IOMEM
-	depends on OF_NET
+	depends on OF
 	select MSCC_OCELOT_SWITCH_LIB
 	select GENERIC_PHY
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mscc/ocelot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mscc/ocelot.c
@@ -555,7 +555,10 @@
 
 	ocelot_write_rix(ocelot, 0, ANA_POL_FLOWC, port);
 
-	ocelot_fields_write(ocelot, port, SYS_PAUSE_CFG_PAUSE_ENA, tx_pause);
+	/* Don't attempt to send PAUSE frames on the NPI port, it's broken */
+	if (port != ocelot->npi)
+		ocelot_fields_write(ocelot, port, SYS_PAUSE_CFG_PAUSE_ENA,
+				    tx_pause);
 
 	/* Undo the effects of ocelot_phylink_mac_link_down:
 	 * enable MAC module
@@ -1175,12 +1178,6 @@
 	switch (cfg.rx_filter) {
 	case HWTSTAMP_FILTER_NONE:
 		break;
-	case HWTSTAMP_FILTER_ALL:
-	case HWTSTAMP_FILTER_SOME:
-	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
-	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
-	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
-	case HWTSTAMP_FILTER_NTP_ALL:
 	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
 	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
@@ -1218,12 +1215,11 @@
 }
 EXPORT_SYMBOL(ocelot_get_strings);
 
+/* Caller must hold &ocelot->stats_lock */
 static void ocelot_update_stats(struct ocelot *ocelot)
 {
 	int i, j;
 
-	mutex_lock(&ocelot->stats_lock);
-
 	for (i = 0; i < ocelot->num_phys_ports; i++) {
 		/* Configure the port to read the stats from */
 		ocelot_write(ocelot, SYS_STAT_CFG_STAT_VIEW(i), SYS_STAT_CFG);
@@ -1242,8 +1238,6 @@
 					      ~(u64)U32_MAX) + val;
 		}
 	}
-
-	mutex_unlock(&ocelot->stats_lock);
 }
 
 static void ocelot_check_stats_work(struct work_struct *work)
@@ -1252,7 +1246,9 @@
 	struct ocelot *ocelot = container_of(del_work, struct ocelot,
 					     stats_work);
 
+	mutex_lock(&ocelot->stats_lock);
 	ocelot_update_stats(ocelot);
+	mutex_unlock(&ocelot->stats_lock);
 
 	queue_delayed_work(ocelot->stats_queue, &ocelot->stats_work,
 			   OCELOT_STATS_CHECK_DELAY);
@@ -1262,12 +1258,16 @@
 {
 	int i;
 
+	mutex_lock(&ocelot->stats_lock);
+
 	/* check and update now */
 	ocelot_update_stats(ocelot);
 
 	/* Copy all counters */
 	for (i = 0; i < ocelot->num_stats; i++)
 		*data++ = ocelot->stats[port * ocelot->num_stats + i];
+
+	mutex_unlock(&ocelot->stats_lock);
 }
 EXPORT_SYMBOL(ocelot_get_ethtool_stats);
 
@@ -1299,14 +1299,16 @@
 				 SOF_TIMESTAMPING_RAW_HARDWARE;
 	info->tx_types = BIT(HWTSTAMP_TX_OFF) | BIT(HWTSTAMP_TX_ON) |
 			 BIT(HWTSTAMP_TX_ONESTEP_SYNC);
-	info->rx_filters = BIT(HWTSTAMP_FILTER_NONE) | BIT(HWTSTAMP_FILTER_ALL);
+	info->rx_filters = BIT(HWTSTAMP_FILTER_NONE) |
+			   BIT(HWTSTAMP_FILTER_PTP_V2_EVENT) |
+			   BIT(HWTSTAMP_FILTER_PTP_V2_L2_EVENT) |
+			   BIT(HWTSTAMP_FILTER_PTP_V2_L4_EVENT);
 
 	return 0;
 }
 EXPORT_SYMBOL(ocelot_get_ts_info);
 
-static u32 ocelot_get_bond_mask(struct ocelot *ocelot, struct net_device *bond,
-				bool only_active_ports)
+static u32 ocelot_get_bond_mask(struct ocelot *ocelot, struct net_device *bond)
 {
 	u32 mask = 0;
 	int port;
@@ -1317,12 +1319,8 @@
 		if (!ocelot_port)
 			continue;
 
-		if (ocelot_port->bond == bond) {
-			if (only_active_ports && !ocelot_port->lag_tx_active)
-				continue;
-
+		if (ocelot_port->bond == bond)
 			mask |= BIT(port);
-		}
 	}
 
 	return mask;
@@ -1409,10 +1407,8 @@
 			mask = ocelot_get_bridge_fwd_mask(ocelot, port, bridge);
 			mask |= cpu_fwd_mask;
 			mask &= ~BIT(port);
-			if (bond) {
-				mask &= ~ocelot_get_bond_mask(ocelot, bond,
-							      false);
-			}
+			if (bond)
+				mask &= ~ocelot_get_bond_mask(ocelot, bond);
 		} else {
 			/* Standalone ports forward only to DSA tag_8021q CPU
 			 * ports (if those exist), or to the hardware CPU port
@@ -1730,13 +1726,17 @@
 		if (!bond || (visited & BIT(lag)))
 			continue;
 
-		bond_mask = ocelot_get_bond_mask(ocelot, bond, true);
+		bond_mask = ocelot_get_bond_mask(ocelot, bond);
 
 		for_each_set_bit(port, &bond_mask, ocelot->num_phys_ports) {
+			struct ocelot_port *ocelot_port = ocelot->ports[port];
+
 			// Destination mask
 			ocelot_write_rix(ocelot, bond_mask,
 					 ANA_PGID_PGID, port);
-			aggr_idx[num_active_ports++] = port;
+
+			if (ocelot_port->lag_tx_active)
+				aggr_idx[num_active_ports++] = port;
 		}
 
 		for_each_aggr_pgid(ocelot, i) {
@@ -1785,8 +1785,7 @@
 
 		bond = ocelot_port->bond;
 		if (bond) {
-			int lag = __ffs(ocelot_get_bond_mask(ocelot, bond,
-							     false));
+			int lag = __ffs(ocelot_get_bond_mask(ocelot, bond));
 
 			ocelot_rmw_gix(ocelot,
 				       ANA_PORT_PORT_CFG_PORTID_VAL(lag),
@@ -1933,6 +1932,8 @@
 		val = BIT(port);
 
 	ocelot_rmw_rix(ocelot, val, BIT(port), ANA_PGID_PGID, PGID_MC);
+	ocelot_rmw_rix(ocelot, val, BIT(port), ANA_PGID_PGID, PGID_MCIPV4);
+	ocelot_rmw_rix(ocelot, val, BIT(port), ANA_PGID_PGID, PGID_MCIPV6);
 }
 
 static void ocelot_port_set_bcast_flood(struct ocelot *ocelot, int port,
@@ -2207,9 +2208,13 @@
 		       ANA_PGID_PGID, PGID_MC);
 	ocelot_rmw_rix(ocelot, ANA_PGID_PGID_PGID(BIT(ocelot->num_phys_ports)),
 		       ANA_PGID_PGID_PGID(BIT(ocelot->num_phys_ports)),
+		       ANA_PGID_PGID, PGID_MCIPV4);
+	ocelot_rmw_rix(ocelot, ANA_PGID_PGID_PGID(BIT(ocelot->num_phys_ports)),
+		       ANA_PGID_PGID_PGID(BIT(ocelot->num_phys_ports)),
+		       ANA_PGID_PGID, PGID_MCIPV6);
+	ocelot_rmw_rix(ocelot, ANA_PGID_PGID_PGID(BIT(ocelot->num_phys_ports)),
+		       ANA_PGID_PGID_PGID(BIT(ocelot->num_phys_ports)),
 		       ANA_PGID_PGID, PGID_BC);
-	ocelot_write_rix(ocelot, 0, ANA_PGID_PGID, PGID_MCIPV4);
-	ocelot_write_rix(ocelot, 0, ANA_PGID_PGID, PGID_MCIPV6);
 
 	/* Allow manual injection via DEVCPU_QS registers, and byte swap these
 	 * registers endianness.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mscc/ocelot_flower.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mscc/ocelot_flower.c
@@ -54,6 +54,12 @@
  */
 static int ocelot_chain_to_lookup(int chain)
 {
+	/* Backwards compatibility with older, single-chain tc-flower
+	 * offload support in Ocelot
+	 */
+	if (chain == 0)
+		return 0;
+
 	return (chain / VCAP_LOOKUP) % 10;
 }
 
@@ -62,7 +68,15 @@
  */
 static int ocelot_chain_to_pag(int chain)
 {
-	int lookup = ocelot_chain_to_lookup(chain);
+	int lookup;
+
+	/* Backwards compatibility with older, single-chain tc-flower
+	 * offload support in Ocelot
+	 */
+	if (chain == 0)
+		return 0;
+
+	lookup = ocelot_chain_to_lookup(chain);
 
 	/* calculate PAG value as chain index relative to the first PAG */
 	return chain - VCAP_IS2_CHAIN(lookup, 0);
@@ -192,9 +206,10 @@
 			filter->type = OCELOT_VCAP_FILTER_OFFLOAD;
 			break;
 		case FLOW_ACTION_TRAP:
-			if (filter->block_id != VCAP_IS2) {
+			if (filter->block_id != VCAP_IS2 ||
+			    filter->lookup != 0) {
 				NL_SET_ERR_MSG_MOD(extack,
-						   "Trap action can only be offloaded to VCAP IS2");
+						   "Trap action can only be offloaded to VCAP IS2 lookup 0");
 				return -EOPNOTSUPP;
 			}
 			if (filter->goto_target != -1) {
@@ -458,6 +473,18 @@
 		flow_rule_match_control(rule, &match);
 	}
 
+	if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_VLAN)) {
+		struct flow_match_vlan match;
+
+		flow_rule_match_vlan(rule, &match);
+		filter->key_type = OCELOT_VCAP_KEY_ANY;
+		filter->vlan.vid.value = match.key->vlan_id;
+		filter->vlan.vid.mask = match.mask->vlan_id;
+		filter->vlan.pcp.value[0] = match.key->vlan_priority;
+		filter->vlan.pcp.mask[0] = match.mask->vlan_priority;
+		match_protocol = false;
+	}
+
 	if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_ETH_ADDRS)) {
 		struct flow_match_eth_addrs match;
 
@@ -467,13 +494,6 @@
 			return -EOPNOTSUPP;
 		}
 
-		if (filter->block_id == VCAP_IS1 &&
-		    !is_zero_ether_addr(match.mask->dst)) {
-			NL_SET_ERR_MSG_MOD(extack,
-					   "Key type S1_NORMAL cannot match on destination MAC");
-			return -EOPNOTSUPP;
-		}
-
 		/* The hw support mac matches only for MAC_ETYPE key,
 		 * therefore if other matches(port, tcp flags, etc) are added
 		 * then just bail out
@@ -488,6 +508,14 @@
 			return -EOPNOTSUPP;
 
 		flow_rule_match_eth_addrs(rule, &match);
+
+		if (filter->block_id == VCAP_IS1 &&
+		    !is_zero_ether_addr(match.mask->dst)) {
+			NL_SET_ERR_MSG_MOD(extack,
+					   "Key type S1_NORMAL cannot match on destination MAC");
+			return -EOPNOTSUPP;
+		}
+
 		filter->key_type = OCELOT_VCAP_KEY_ETYPE;
 		ether_addr_copy(filter->key.etype.dmac.value,
 				match.key->dst);
@@ -589,18 +617,6 @@
 		match_protocol = false;
 	}
 
-	if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_VLAN)) {
-		struct flow_match_vlan match;
-
-		flow_rule_match_vlan(rule, &match);
-		filter->key_type = OCELOT_VCAP_KEY_ANY;
-		filter->vlan.vid.value = match.key->vlan_id;
-		filter->vlan.vid.mask = match.mask->vlan_id;
-		filter->vlan.pcp.value[0] = match.key->vlan_priority;
-		filter->vlan.pcp.mask[0] = match.mask->vlan_priority;
-		match_protocol = false;
-	}
-
 finished_key_parsing:
 	if (match_protocol && proto != ETH_P_ALL) {
 		if (filter->block_id == VCAP_ES0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mscc/ocelot_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mscc/ocelot_net.c
@@ -606,7 +606,7 @@
 	/* Then forget the previous one. */
 	ocelot_mact_forget(ocelot, dev->dev_addr, ocelot_port->pvid_vlan.vid);
 
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 	return 0;
 }
 
@@ -1168,7 +1168,7 @@
 	ocelot_port_bridge_join(ocelot, port, bridge);
 
 	err = switchdev_bridge_port_offload(brport_dev, dev, priv,
-					    &ocelot_netdevice_nb,
+					    &ocelot_switchdev_nb,
 					    &ocelot_switchdev_blocking_nb,
 					    false, extack);
 	if (err)
@@ -1182,7 +1182,7 @@
 
 err_switchdev_sync:
 	switchdev_bridge_port_unoffload(brport_dev, priv,
-					&ocelot_netdevice_nb,
+					&ocelot_switchdev_nb,
 					&ocelot_switchdev_blocking_nb);
 err_switchdev_offload:
 	ocelot_port_bridge_leave(ocelot, port, bridge);
@@ -1195,7 +1195,7 @@
 	struct ocelot_port_private *priv = netdev_priv(dev);
 
 	switchdev_bridge_port_unoffload(brport_dev, priv,
-					&ocelot_netdevice_nb,
+					&ocelot_switchdev_nb,
 					&ocelot_switchdev_blocking_nb);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/mscc/ocelot_vcap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/mscc/ocelot_vcap.c
@@ -373,7 +373,6 @@
 			 OCELOT_VCAP_BIT_0);
 	vcap_key_set(vcap, &data, VCAP_IS2_HK_IGR_PORT_MASK, 0,
 		     ~filter->ingress_port_mask);
-	vcap_key_bit_set(vcap, &data, VCAP_IS2_HK_FIRST, OCELOT_VCAP_BIT_ANY);
 	vcap_key_bit_set(vcap, &data, VCAP_IS2_HK_HOST_MATCH,
 			 OCELOT_VCAP_BIT_ANY);
 	vcap_key_bit_set(vcap, &data, VCAP_IS2_HK_L2_MC, filter->dmac_mc);
@@ -1153,6 +1152,8 @@
 		struct ocelot_vcap_filter *tmp;
 
 		tmp = ocelot_vcap_block_find_filter_by_index(block, i);
+		/* Read back the filter's counters before moving it */
+		vcap_entry_get(ocelot, i - 1, tmp);
 		vcap_entry_set(ocelot, i, tmp);
 	}
 
@@ -1192,7 +1193,11 @@
 	struct ocelot_vcap_filter del_filter;
 	int i, index;
 
+	/* Need to inherit the block_id so that vcap_entry_set()
+	 * does not get confused and knows where to install it.
+	 */
 	memset(&del_filter, 0, sizeof(del_filter));
+	del_filter.block_id = filter->block_id;
 
 	/* Gets index of the filter */
 	index = ocelot_vcap_block_get_filter_index(block, filter);
@@ -1207,6 +1212,8 @@
 		struct ocelot_vcap_filter *tmp;
 
 		tmp = ocelot_vcap_block_find_filter_by_index(block, i);
+		/* Read back the filter's counters before moving it */
+		vcap_entry_get(ocelot, i + 1, tmp);
 		vcap_entry_set(ocelot, i, tmp);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
@@ -796,7 +796,8 @@
 	return status;
 }
 
-static int myri10ge_update_mac_address(struct myri10ge_priv *mgp, u8 * addr)
+static int myri10ge_update_mac_address(struct myri10ge_priv *mgp,
+				       const u8 * addr)
 {
 	struct myri10ge_cmd cmd;
 	int status;
@@ -2900,11 +2901,9 @@
 		status = myri10ge_xmit(curr, dev);
 		if (status != 0) {
 			dev_kfree_skb_any(curr);
-			if (segs != NULL) {
-				curr = segs;
-				segs = next;
+			skb_list_walk_safe(next, curr, next) {
 				curr->next = NULL;
-				dev_kfree_skb_any(segs);
+				dev_kfree_skb_any(curr);
 			}
 			goto drop;
 		}
@@ -3925,6 +3924,7 @@
 	myri10ge_free_slices(mgp);
 
 abort_with_firmware:
+	kfree(mgp->msix_vectors);
 	myri10ge_dummy_rdma(mgp, 0);
 
 abort_with_ioremap:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/natsemi/sonic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/natsemi/sonic.c
@@ -292,7 +292,7 @@
 	 */
 
 	laddr = dma_map_single(lp->device, skb->data, length, DMA_TO_DEVICE);
-	if (!laddr) {
+	if (dma_mapping_error(lp->device, laddr)) {
 		pr_err_ratelimited("%s: failed to map tx DMA buffer.\n", dev->name);
 		dev_kfree_skb_any(skb);
 		return NETDEV_TX_OK;
@@ -509,7 +509,7 @@
 
 	*new_addr = dma_map_single(lp->device, skb_put(*new_skb, SONIC_RBSIZE),
 				   SONIC_RBSIZE, DMA_FROM_DEVICE);
-	if (!*new_addr) {
+	if (dma_mapping_error(lp->device, *new_addr)) {
 		dev_kfree_skb(*new_skb);
 		*new_skb = NULL;
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/natsemi/xtsonic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/natsemi/xtsonic.c
@@ -120,7 +120,7 @@
 	.ndo_set_mac_address	= eth_mac_addr,
 };
 
-static int __init sonic_probe1(struct net_device *dev)
+static int sonic_probe1(struct net_device *dev)
 {
 	unsigned int silicon_revision;
 	struct sonic_local *lp = netdev_priv(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/neterion/s2io.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/neterion/s2io.c
@@ -2386,7 +2386,7 @@
 			skb = s2io_txdl_getskb(&mac_control->fifos[i], txdp, j);
 			if (skb) {
 				swstats->mem_freed += skb->truesize;
-				dev_kfree_skb(skb);
+				dev_kfree_skb_irq(skb);
 				cnt++;
 			}
 		}
@@ -5217,7 +5217,7 @@
  *  as defined in errno.h file on failure.
  */
 
-static int do_s2io_prog_unicast(struct net_device *dev, u8 *addr)
+static int do_s2io_prog_unicast(struct net_device *dev, const u8 *addr)
 {
 	struct s2io_nic *sp = netdev_priv(dev);
 	register u64 mac_addr = 0, perm_addr = 0;
@@ -7125,9 +7125,8 @@
 		if (ret) {
 			DBG_PRINT(ERR_DBG, "%s: Out of memory in Open\n",
 				  dev->name);
-			s2io_reset(sp);
-			free_rx_buffers(sp);
-			return -ENOMEM;
+			ret = -ENOMEM;
+			goto err_fill_buff;
 		}
 		DBG_PRINT(INFO_DBG, "Buf in ring:%d is %d:\n", i,
 			  ring->rx_bufs_left);
@@ -7165,18 +7164,16 @@
 	/* Enable Rx Traffic and interrupts on the NIC */
 	if (start_nic(sp)) {
 		DBG_PRINT(ERR_DBG, "%s: Starting NIC failed\n", dev->name);
-		s2io_reset(sp);
-		free_rx_buffers(sp);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto err_out;
 	}
 
 	/* Add interrupt service routine */
 	if (s2io_add_isr(sp) != 0) {
 		if (sp->config.intr_type == MSI_X)
 			s2io_rem_isr(sp);
-		s2io_reset(sp);
-		free_rx_buffers(sp);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto err_out;
 	}
 
 	timer_setup(&sp->alarm_timer, s2io_alarm_handle, 0);
@@ -7196,6 +7193,20 @@
 	}
 
 	return 0;
+
+err_out:
+	if (config->napi) {
+		if (config->intr_type == MSI_X) {
+			for (i = 0; i < sp->config.rx_ring_num; i++)
+				napi_disable(&sp->mac_control.rings[i].napi);
+		} else {
+			napi_disable(&sp->napi);
+		}
+	}
+err_fill_buff:
+	s2io_reset(sp);
+	free_rx_buffers(sp);
+	return ret;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/neterion/s2io.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/neterion/s2io.h
@@ -1073,7 +1073,7 @@
 static int s2io_poll_msix(struct napi_struct *napi, int budget);
 static int s2io_poll_inta(struct napi_struct *napi, int budget);
 static void s2io_init_pci(struct s2io_nic * sp);
-static int do_s2io_prog_unicast(struct net_device *dev, u8 *addr);
+static int do_s2io_prog_unicast(struct net_device *dev, const u8 *addr);
 static void s2io_alarm_handle(struct timer_list *t);
 static irqreturn_t
 s2io_msix_ring_handle(int irq, void *dev_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/neterion/vxge/vxge-main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/neterion/vxge/vxge-main.c
@@ -4183,6 +4183,9 @@
 	return ret;
 }
 
+#define VXGE_PXE_FIRMWARE "vxge/X3fw-pxe.ncf"
+#define VXGE_FIRMWARE "vxge/X3fw.ncf"
+
 static int vxge_probe_fw_update(struct vxgedev *vdev)
 {
 	u32 maj, min, bld;
@@ -4225,9 +4228,9 @@
 			}
 	}
 	if (gpxe)
-		fw_name = "vxge/X3fw-pxe.ncf";
+		fw_name = VXGE_PXE_FIRMWARE;
 	else
-		fw_name = "vxge/X3fw.ncf";
+		fw_name = VXGE_FIRMWARE;
 
 	ret = vxge_fw_upgrade(vdev, fw_name, 0);
 	/* -EINVAL and -ENOENT are not fatal errors for flashing firmware on
@@ -4830,3 +4833,5 @@
 }
 module_init(vxge_starter);
 module_exit(vxge_closer);
+MODULE_FIRMWARE(VXGE_PXE_FIRMWARE);
+MODULE_FIRMWARE(VXGE_FIRMWARE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/abm/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/abm/main.c
@@ -305,7 +305,7 @@
 		return;
 	}
 
-	ether_addr_copy(nn->dp.netdev->dev_addr, mac_addr);
+	eth_hw_addr_set(nn->dp.netdev, mac_addr);
 	ether_addr_copy(nn->dp.netdev->perm_addr, mac_addr);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/bpf/cmsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/bpf/cmsg.c
@@ -20,6 +20,8 @@
 	struct sk_buff *skb;
 
 	skb = nfp_app_ctrl_msg_alloc(bpf->app, size, GFP_KERNEL);
+	if (!skb)
+		return NULL;
 	skb_put(skb, size);
 
 	return skb;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/bpf/offload.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/bpf/offload.c
@@ -458,7 +458,8 @@
 	map_id_full = be64_to_cpu(cbe->map_ptr);
 	map_id = map_id_full;
 
-	if (len < sizeof(struct cmsg_bpf_event) + pkt_size + data_size)
+	if (size_add(pkt_size, data_size) > INT_MAX ||
+	    len < sizeof(struct cmsg_bpf_event) + pkt_size + data_size)
 		return -EINVAL;
 	if (cbe->hdr.ver != NFP_CCM_ABI_VERSION)
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/action.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/action.c
@@ -472,7 +472,7 @@
 			set_tun->ttl = ip4_dst_hoplimit(&rt->dst);
 			ip_rt_put(rt);
 		} else {
-			set_tun->ttl = net->ipv4.sysctl_ip_default_ttl;
+			set_tun->ttl = READ_ONCE(net->ipv4.sysctl_ip_default_ttl);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/cmsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/cmsg.c
@@ -210,6 +210,7 @@
 	unsigned int msg_len = nfp_flower_cmsg_get_data_len(skb);
 	struct nfp_flower_cmsg_merge_hint *msg;
 	struct nfp_fl_payload *sub_flows[2];
+	struct nfp_flower_priv *priv;
 	int err, i, flow_cnt;
 
 	msg = nfp_flower_cmsg_get_data(skb);
@@ -228,14 +229,15 @@
 		return;
 	}
 
-	rtnl_lock();
+	priv = app->priv;
+	mutex_lock(&priv->nfp_fl_lock);
 	for (i = 0; i < flow_cnt; i++) {
 		u32 ctx = be32_to_cpu(msg->flow[i].host_ctx);
 
 		sub_flows[i] = nfp_flower_get_fl_payload_from_ctx(app, ctx);
 		if (!sub_flows[i]) {
 			nfp_flower_cmsg_warn(app, "Invalid flow in merge hint\n");
-			goto err_rtnl_unlock;
+			goto err_mutex_unlock;
 		}
 	}
 
@@ -244,8 +246,8 @@
 	if (err == -ENOMEM)
 		nfp_flower_cmsg_warn(app, "Flow merge memory fail.\n");
 
-err_rtnl_unlock:
-	rtnl_unlock();
+err_mutex_unlock:
+	mutex_unlock(&priv->nfp_fl_lock);
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/conntrack.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/conntrack.c
@@ -442,6 +442,11 @@
 		key_size += sizeof(struct nfp_flower_ipv6);
 	}
 
+	if (in_key_ls.key_layer_two & NFP_FLOWER_LAYER2_QINQ) {
+		map[FLOW_PAY_QINQ] = key_size;
+		key_size += sizeof(struct nfp_flower_vlan);
+	}
+
 	if (in_key_ls.key_layer_two & NFP_FLOWER_LAYER2_GRE) {
 		map[FLOW_PAY_GRE] = key_size;
 		if (in_key_ls.key_layer_two & NFP_FLOWER_LAYER2_TUN_IPV6)
@@ -450,11 +455,6 @@
 			key_size += sizeof(struct nfp_flower_ipv4_gre_tun);
 	}
 
-	if (in_key_ls.key_layer_two & NFP_FLOWER_LAYER2_QINQ) {
-		map[FLOW_PAY_QINQ] = key_size;
-		key_size += sizeof(struct nfp_flower_vlan);
-	}
-
 	if ((in_key_ls.key_layer & NFP_FLOWER_LAYER_VXLAN) ||
 	    (in_key_ls.key_layer_two & NFP_FLOWER_LAYER2_GENEVE)) {
 		map[FLOW_PAY_UDP_TUN] = key_size;
@@ -693,6 +693,17 @@
 		}
 	}
 
+	if (NFP_FLOWER_LAYER2_QINQ & key_layer.key_layer_two) {
+		offset = key_map[FLOW_PAY_QINQ];
+		key = kdata + offset;
+		msk = mdata + offset;
+		for (i = 0; i < _CT_TYPE_MAX; i++) {
+			nfp_flower_compile_vlan((struct nfp_flower_vlan *)key,
+						(struct nfp_flower_vlan *)msk,
+						rules[i]);
+		}
+	}
+
 	if (key_layer.key_layer_two & NFP_FLOWER_LAYER2_GRE) {
 		offset = key_map[FLOW_PAY_GRE];
 		key = kdata + offset;
@@ -733,17 +744,6 @@
 		}
 	}
 
-	if (NFP_FLOWER_LAYER2_QINQ & key_layer.key_layer_two) {
-		offset = key_map[FLOW_PAY_QINQ];
-		key = kdata + offset;
-		msk = mdata + offset;
-		for (i = 0; i < _CT_TYPE_MAX; i++) {
-			nfp_flower_compile_vlan((struct nfp_flower_vlan *)key,
-						(struct nfp_flower_vlan *)msk,
-						rules[i]);
-		}
-	}
-
 	if (key_layer.key_layer & NFP_FLOWER_LAYER_VXLAN ||
 	    key_layer.key_layer_two & NFP_FLOWER_LAYER2_GENEVE) {
 		offset = key_map[FLOW_PAY_UDP_TUN];
@@ -1004,7 +1004,7 @@
 	/* Checks that the chain_index of the filter matches the
 	 * chain_index of the GOTO action.
 	 */
-	if (post_ct_entry->chain_index != pre_ct_entry->chain_index)
+	if (post_ct_entry->chain_index != pre_ct_entry->goto_chain_index)
 		return -EINVAL;
 
 	err = nfp_ct_merge_check(post_ct_entry, pre_ct_entry);
@@ -1450,7 +1450,8 @@
 	if (IS_ERR(ct_entry))
 		return PTR_ERR(ct_entry);
 	ct_entry->type = CT_TYPE_PRE_CT;
-	ct_entry->chain_index = ct_goto->chain_index;
+	ct_entry->chain_index = flow->common.chain_index;
+	ct_entry->goto_chain_index = ct_goto->chain_index;
 	list_add(&ct_entry->list_node, &zt->pre_ct_list);
 	zt->pre_ct_count++;
 
@@ -1470,9 +1471,30 @@
 {
 	struct flow_rule *rule = flow_cls_offload_flow_rule(flow);
 	struct nfp_fl_ct_flow_entry *ct_entry;
+	struct flow_action_entry *ct_goto;
 	struct nfp_fl_ct_zone_entry *zt;
+	struct flow_action_entry *act;
 	bool wildcarded = false;
 	struct flow_match_ct ct;
+	int i;
+
+	flow_action_for_each(i, act, &rule->action) {
+		switch (act->id) {
+		case FLOW_ACTION_REDIRECT:
+		case FLOW_ACTION_REDIRECT_INGRESS:
+		case FLOW_ACTION_MIRRED:
+		case FLOW_ACTION_MIRRED_INGRESS:
+			if (act->dev->rtnl_link_ops &&
+			    !strcmp(act->dev->rtnl_link_ops->kind, "openvswitch")) {
+				NL_SET_ERR_MSG_MOD(extack,
+						   "unsupported offload: out port is openvswitch internal port");
+				return -EOPNOTSUPP;
+			}
+			break;
+		default:
+			break;
+		}
+	}
 
 	flow_rule_match_ct(rule, &ct);
 	if (!ct.mask->ct_zone) {
@@ -1497,6 +1519,8 @@
 
 	ct_entry->type = CT_TYPE_POST_CT;
 	ct_entry->chain_index = flow->common.chain_index;
+	ct_goto = get_flow_act(flow->rule, FLOW_ACTION_GOTO);
+	ct_entry->goto_chain_index = ct_goto ? ct_goto->chain_index : 0;
 	list_add(&ct_entry->list_node, &zt->post_ct_list);
 	zt->post_ct_count++;
 
@@ -1665,8 +1689,6 @@
 	struct nfp_fl_ct_flow_entry *ct_entry;
 	struct netlink_ext_ack *extack = NULL;
 
-	ASSERT_RTNL();
-
 	extack = flow->common.extack;
 	switch (flow->command) {
 	case FLOW_CLS_REPLACE:
@@ -1709,9 +1731,13 @@
 
 	switch (type) {
 	case TC_SETUP_CLSFLOWER:
-		rtnl_lock();
+		while (!mutex_trylock(&zt->priv->nfp_fl_lock)) {
+			if (!zt->nft) /* avoid deadlock */
+				return err;
+			msleep(20);
+		}
 		err = nfp_fl_ct_offload_nft_flow(zt, flow);
-		rtnl_unlock();
+		mutex_unlock(&zt->priv->nfp_fl_lock);
 		break;
 	default:
 		return -EOPNOTSUPP;
@@ -1739,6 +1765,7 @@
 	struct nfp_fl_ct_flow_entry *ct_entry;
 	struct nfp_fl_ct_zone_entry *zt;
 	struct rhashtable *m_table;
+	struct nf_flowtable *nft;
 
 	if (!ct_map_ent)
 		return -ENOENT;
@@ -1755,8 +1782,12 @@
 		nfp_fl_ct_clean_flow_entry(ct_entry);
 		kfree(ct_map_ent);
 
-		if (!zt->pre_ct_count) {
-			zt->nft = NULL;
+		if (!zt->pre_ct_count && zt->nft) {
+			nft = zt->nft;
+			zt->nft = NULL; /* avoid deadlock */
+			nf_flow_table_offload_del_cb(nft,
+						     nfp_fl_ct_handle_nft_flow,
+						     zt);
 			nfp_fl_ct_clean_nft_entries(zt);
 		}
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/conntrack.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/conntrack.h
@@ -108,6 +108,7 @@
  * @cookie:	Flow cookie, same as original TC flow, used as key
  * @list_node:	Used by the list
  * @chain_index:	Chain index of the original flow
+ * @goto_chain_index:	goto chain index of the flow
  * @netdev:	netdev structure.
  * @type:	Type of pre-entry from enum ct_entry_type
  * @zt:		Reference to the zone table this belongs to
@@ -120,6 +121,7 @@
 	unsigned long cookie;
 	struct list_head list_node;
 	u32 chain_index;
+	u32 goto_chain_index;
 	enum ct_entry_type type;
 	struct net_device *netdev;
 	struct nfp_fl_ct_zone_entry *zt;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/lag_conf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/lag_conf.c
@@ -308,6 +308,11 @@
 
 		acti_netdevs = kmalloc_array(entry->slave_cnt,
 					     sizeof(*acti_netdevs), GFP_KERNEL);
+		if (!acti_netdevs) {
+			schedule_delayed_work(&lag->work,
+					      NFP_FL_LAG_DELAY);
+			continue;
+		}
 
 		/* Include sanity check in the loop. It may be that a bond has
 		 * changed between processing the last notification and the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/main.h
@@ -196,6 +196,7 @@
  * @ct_zone_table:	Hash table used to store the different zones
  * @ct_zone_wc:		Special zone entry for wildcarded zone matches
  * @ct_map_table:	Hash table used to referennce ct flows
+ * @nfp_fl_lock:	Lock to protect the flow offload operation
  */
 struct nfp_flower_priv {
 	struct nfp_app *app;
@@ -233,6 +234,7 @@
 	struct rhashtable ct_zone_table;
 	struct nfp_fl_ct_zone_entry *ct_zone_wc;
 	struct rhashtable ct_map_table;
+	struct mutex nfp_fl_lock; /* Protect the flow operation */
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/match.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/match.c
@@ -602,6 +602,14 @@
 		msk += sizeof(struct nfp_flower_ipv6);
 	}
 
+	if (NFP_FLOWER_LAYER2_QINQ & key_ls->key_layer_two) {
+		nfp_flower_compile_vlan((struct nfp_flower_vlan *)ext,
+					(struct nfp_flower_vlan *)msk,
+					rule);
+		ext += sizeof(struct nfp_flower_vlan);
+		msk += sizeof(struct nfp_flower_vlan);
+	}
+
 	if (key_ls->key_layer_two & NFP_FLOWER_LAYER2_GRE) {
 		if (key_ls->key_layer_two & NFP_FLOWER_LAYER2_TUN_IPV6) {
 			struct nfp_flower_ipv6_gre_tun *gre_match;
@@ -637,14 +645,6 @@
 		}
 	}
 
-	if (NFP_FLOWER_LAYER2_QINQ & key_ls->key_layer_two) {
-		nfp_flower_compile_vlan((struct nfp_flower_vlan *)ext,
-					(struct nfp_flower_vlan *)msk,
-					rule);
-		ext += sizeof(struct nfp_flower_vlan);
-		msk += sizeof(struct nfp_flower_vlan);
-	}
-
 	if (key_ls->key_layer & NFP_FLOWER_LAYER_VXLAN ||
 	    key_ls->key_layer_two & NFP_FLOWER_LAYER2_GENEVE) {
 		if (key_ls->key_layer_two & NFP_FLOWER_LAYER2_TUN_IPV6) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/metadata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/metadata.c
@@ -530,6 +530,8 @@
 	if (err)
 		goto err_free_stats_ctx_table;
 
+	mutex_init(&priv->nfp_fl_lock);
+
 	err = rhashtable_init(&priv->ct_zone_table, &nfp_zone_table_params);
 	if (err)
 		goto err_free_merge_table;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/offload.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/offload.c
@@ -1009,8 +1009,6 @@
 	u64 parent_ctx = 0;
 	int err;
 
-	ASSERT_RTNL();
-
 	if (sub_flow1 == sub_flow2 ||
 	    nfp_flower_is_merge_flow(sub_flow1) ||
 	    nfp_flower_is_merge_flow(sub_flow2))
@@ -1662,19 +1660,30 @@
 nfp_flower_repr_offload(struct nfp_app *app, struct net_device *netdev,
 			struct flow_cls_offload *flower)
 {
+	struct nfp_flower_priv *priv = app->priv;
+	int ret;
+
 	if (!eth_proto_is_802_3(flower->common.protocol))
 		return -EOPNOTSUPP;
 
+	mutex_lock(&priv->nfp_fl_lock);
 	switch (flower->command) {
 	case FLOW_CLS_REPLACE:
-		return nfp_flower_add_offload(app, netdev, flower);
+		ret = nfp_flower_add_offload(app, netdev, flower);
+		break;
 	case FLOW_CLS_DESTROY:
-		return nfp_flower_del_offload(app, netdev, flower);
+		ret = nfp_flower_del_offload(app, netdev, flower);
+		break;
 	case FLOW_CLS_STATS:
-		return nfp_flower_get_stats(app, netdev, flower);
+		ret = nfp_flower_get_stats(app, netdev, flower);
+		break;
 	default:
-		return -EOPNOTSUPP;
+		ret = -EOPNOTSUPP;
+		break;
 	}
+	mutex_unlock(&priv->nfp_fl_lock);
+
+	return ret;
 }
 
 static int nfp_flower_setup_tc_block_cb(enum tc_setup_type type,
@@ -1713,6 +1722,7 @@
 	repr_priv = repr->app_priv;
 	repr_priv->block_shared = f->block_shared;
 	f->driver_block_list = &nfp_block_cb_list;
+	f->unlocked_driver_cb = true;
 
 	switch (f->command) {
 	case FLOW_BLOCK_BIND:
@@ -1811,6 +1821,8 @@
 	     nfp_flower_internal_port_can_offload(app, netdev)))
 		return -EOPNOTSUPP;
 
+	f->unlocked_driver_cb = true;
+
 	switch (f->command) {
 	case FLOW_BLOCK_BIND:
 		cb_priv = nfp_flower_indr_block_cb_priv_lookup(app, netdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/qos_conf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/qos_conf.c
@@ -421,23 +421,29 @@
 {
 	struct netlink_ext_ack *extack = flow->common.extack;
 	struct nfp_flower_priv *fl_priv = app->priv;
+	int ret;
 
 	if (!(fl_priv->flower_ext_feats & NFP_FL_FEATS_VF_RLIM)) {
 		NL_SET_ERR_MSG_MOD(extack, "unsupported offload: loaded firmware does not support qos rate limit offload");
 		return -EOPNOTSUPP;
 	}
 
+	mutex_lock(&fl_priv->nfp_fl_lock);
 	switch (flow->command) {
 	case TC_CLSMATCHALL_REPLACE:
-		return nfp_flower_install_rate_limiter(app, netdev, flow,
-						       extack);
+		ret = nfp_flower_install_rate_limiter(app, netdev, flow, extack);
+		break;
 	case TC_CLSMATCHALL_DESTROY:
-		return nfp_flower_remove_rate_limiter(app, netdev, flow,
-						      extack);
+		ret = nfp_flower_remove_rate_limiter(app, netdev, flow, extack);
+		break;
 	case TC_CLSMATCHALL_STATS:
-		return nfp_flower_stats_rate_limiter(app, netdev, flow,
-						     extack);
+		ret = nfp_flower_stats_rate_limiter(app, netdev, flow, extack);
+		break;
 	default:
-		return -EOPNOTSUPP;
+		ret = -EOPNOTSUPP;
+		break;
 	}
+	mutex_unlock(&fl_priv->nfp_fl_lock);
+
+	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/flower/tunnel_conf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/flower/tunnel_conf.c
@@ -837,7 +837,7 @@
 }
 
 static int
-__nfp_tunnel_offload_mac(struct nfp_app *app, u8 *mac, u16 idx, bool del)
+__nfp_tunnel_offload_mac(struct nfp_app *app, const u8 *mac, u16 idx, bool del)
 {
 	struct nfp_tun_mac_addr_offload payload;
 
@@ -886,7 +886,7 @@
 }
 
 static struct nfp_tun_offloaded_mac *
-nfp_tunnel_lookup_offloaded_macs(struct nfp_app *app, u8 *mac)
+nfp_tunnel_lookup_offloaded_macs(struct nfp_app *app, const u8 *mac)
 {
 	struct nfp_flower_priv *priv = app->priv;
 
@@ -922,12 +922,12 @@
 			  int port, bool mod)
 {
 	struct nfp_flower_priv *priv = app->priv;
-	int ida_idx = NFP_MAX_MAC_INDEX, err;
 	struct nfp_tun_offloaded_mac *entry;
+	int ida_idx = -1, err;
 	u16 nfp_mac_idx = 0;
 
 	entry = nfp_tunnel_lookup_offloaded_macs(app, netdev->dev_addr);
-	if (entry && nfp_tunnel_is_mac_idx_global(entry->index)) {
+	if (entry && (nfp_tunnel_is_mac_idx_global(entry->index) || netif_is_lag_port(netdev))) {
 		if (entry->bridge_count ||
 		    !nfp_flower_is_supported_bridge(netdev)) {
 			nfp_tunnel_offloaded_macs_inc_ref_and_link(entry,
@@ -997,7 +997,7 @@
 err_free_entry:
 	kfree(entry);
 err_free_ida:
-	if (ida_idx != NFP_MAX_MAC_INDEX)
+	if (ida_idx != -1)
 		ida_simple_remove(&priv->tun.mac_off_ids, ida_idx);
 
 	return err;
@@ -1005,12 +1005,13 @@
 
 static int
 nfp_tunnel_del_shared_mac(struct nfp_app *app, struct net_device *netdev,
-			  u8 *mac, bool mod)
+			  const u8 *mac, bool mod)
 {
 	struct nfp_flower_priv *priv = app->priv;
 	struct nfp_flower_repr_priv *repr_priv;
 	struct nfp_tun_offloaded_mac *entry;
 	struct nfp_repr *repr;
+	u16 nfp_mac_idx;
 	int ida_idx;
 
 	entry = nfp_tunnel_lookup_offloaded_macs(app, mac);
@@ -1029,8 +1030,6 @@
 		entry->bridge_count--;
 
 		if (!entry->bridge_count && entry->ref_count) {
-			u16 nfp_mac_idx;
-
 			nfp_mac_idx = entry->index & ~NFP_TUN_PRE_TUN_IDX_BIT;
 			if (__nfp_tunnel_offload_mac(app, mac, nfp_mac_idx,
 						     false)) {
@@ -1046,7 +1045,6 @@
 
 	/* If MAC is now used by 1 repr set the offloaded MAC index to port. */
 	if (entry->ref_count == 1 && list_is_singular(&entry->repr_list)) {
-		u16 nfp_mac_idx;
 		int port, err;
 
 		repr_priv = list_first_entry(&entry->repr_list,
@@ -1074,8 +1072,14 @@
 	WARN_ON_ONCE(rhashtable_remove_fast(&priv->tun.offloaded_macs,
 					    &entry->ht_node,
 					    offloaded_macs_params));
+
+	if (nfp_flower_is_supported_bridge(netdev))
+		nfp_mac_idx = entry->index & ~NFP_TUN_PRE_TUN_IDX_BIT;
+	else
+		nfp_mac_idx = entry->index;
+
 	/* If MAC has global ID then extract and free the ida entry. */
-	if (nfp_tunnel_is_mac_idx_global(entry->index)) {
+	if (nfp_tunnel_is_mac_idx_global(nfp_mac_idx)) {
 		ida_idx = nfp_tunnel_get_ida_from_global_mac_idx(entry->index);
 		ida_simple_remove(&priv->tun.mac_off_ids, ida_idx);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfp_devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfp_devlink.c
@@ -363,7 +363,7 @@
 		return ret;
 
 	attrs.split = eth_port.is_split;
-	attrs.splittable = !attrs.split;
+	attrs.splittable = eth_port.port_lanes > 1 && !attrs.split;
 	attrs.lanes = eth_port.port_lanes;
 	attrs.flavour = DEVLINK_PORT_FLAVOUR_PHYSICAL;
 	attrs.phys.port_number = eth_port.label_port;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfp_net.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfp_net.h
@@ -565,7 +565,6 @@
  * @exn_name:           Name for Exception interrupt
  * @shared_handler:     Handler for shared interrupts
  * @shared_name:        Name for shared interrupt
- * @me_freq_mhz:        ME clock_freq (MHz)
  * @reconfig_lock:	Protects @reconfig_posted, @reconfig_timer_active,
  *			@reconfig_sync_present and HW reconfiguration request
  *			regs/machinery from async requests (sync must take
@@ -650,8 +649,6 @@
 	irq_handler_t shared_handler;
 	char shared_name[IFNAMSIZ + 8];
 
-	u32 me_freq_mhz;
-
 	bool link_up;
 	spinlock_t link_status_lock;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfp_net_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfp_net_common.c
@@ -2067,7 +2067,7 @@
 		if (napi_complete_done(napi, pkts_polled))
 			nfp_net_irq_unmask(r_vec->nfp_net, r_vec->irq_entry);
 
-	if (r_vec->nfp_net->rx_coalesce_adapt_on) {
+	if (r_vec->nfp_net->rx_coalesce_adapt_on && r_vec->rx_ring) {
 		struct dim_sample dim_sample = {};
 		unsigned int start;
 		u64 pkts, bytes;
@@ -2082,7 +2082,7 @@
 		net_dim(&r_vec->rx_dim, dim_sample);
 	}
 
-	if (r_vec->nfp_net->tx_coalesce_adapt_on) {
+	if (r_vec->nfp_net->tx_coalesce_adapt_on && r_vec->tx_ring) {
 		struct dim_sample dim_sample = {};
 		unsigned int start;
 		u64 pkts, bytes;
@@ -2665,8 +2665,8 @@
 
 	snprintf(r_vec->name, sizeof(r_vec->name),
 		 "%s-rxtx-%d", nfp_net_name(nn), idx);
-	err = request_irq(r_vec->irq_vector, r_vec->handler, 0, r_vec->name,
-			  r_vec);
+	err = request_irq(r_vec->irq_vector, r_vec->handler, IRQF_NO_AUTOEN,
+			  r_vec->name, r_vec);
 	if (err) {
 		if (nn->dp.netdev)
 			netif_napi_del(&r_vec->napi);
@@ -2676,7 +2676,6 @@
 		nn_err(nn, "Error requesting IRQ %d\n", r_vec->irq_vector);
 		return err;
 	}
-	disable_irq(r_vec->irq_vector);
 
 	irq_set_affinity_hint(r_vec->irq_vector, &r_vec->affinity_mask);
 
@@ -3016,10 +3015,8 @@
 
 	/* copy RX interrupt coalesce parameters */
 	value = (moder.pkts << 16) | (factor * moder.usec);
-	rtnl_lock();
 	nn_writel(nn, NFP_NET_CFG_RXR_IRQ_MOD(r_vec->rx_ring->idx), value);
 	(void)nfp_net_reconfig(nn, NFP_NET_CFG_UPDATE_IRQMOD);
-	rtnl_unlock();
 
 	dim->state = DIM_START_MEASURE;
 }
@@ -3047,10 +3044,8 @@
 
 	/* copy TX interrupt coalesce parameters */
 	value = (moder.pkts << 16) | (factor * moder.usec);
-	rtnl_lock();
 	nn_writel(nn, NFP_NET_CFG_TXR_IRQ_MOD(r_vec->tx_ring->idx), value);
 	(void)nfp_net_reconfig(nn, NFP_NET_CFG_UPDATE_IRQMOD);
-	rtnl_unlock();
 
 	dim->state = DIM_START_MEASURE;
 }
@@ -3486,21 +3481,21 @@
 		unsigned int start;
 
 		do {
-			start = u64_stats_fetch_begin(&r_vec->rx_sync);
+			start = u64_stats_fetch_begin_irq(&r_vec->rx_sync);
 			data[0] = r_vec->rx_pkts;
 			data[1] = r_vec->rx_bytes;
 			data[2] = r_vec->rx_drops;
-		} while (u64_stats_fetch_retry(&r_vec->rx_sync, start));
+		} while (u64_stats_fetch_retry_irq(&r_vec->rx_sync, start));
 		stats->rx_packets += data[0];
 		stats->rx_bytes += data[1];
 		stats->rx_dropped += data[2];
 
 		do {
-			start = u64_stats_fetch_begin(&r_vec->tx_sync);
+			start = u64_stats_fetch_begin_irq(&r_vec->tx_sync);
 			data[0] = r_vec->tx_pkts;
 			data[1] = r_vec->tx_bytes;
 			data[2] = r_vec->tx_errors;
-		} while (u64_stats_fetch_retry(&r_vec->tx_sync, start));
+		} while (u64_stats_fetch_retry_irq(&r_vec->tx_sync, start));
 		stats->tx_packets += data[0];
 		stats->tx_bytes += data[1];
 		stats->tx_errors += data[2];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfp_net_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfp_net_ethtool.c
@@ -286,8 +286,6 @@
 
 	/* Init to unknowns */
 	ethtool_link_ksettings_add_link_mode(cmd, supported, FIBRE);
-	ethtool_link_ksettings_add_link_mode(cmd, supported, Pause);
-	ethtool_link_ksettings_add_link_mode(cmd, advertising, Pause);
 	cmd->base.port = PORT_OTHER;
 	cmd->base.speed = SPEED_UNKNOWN;
 	cmd->base.duplex = DUPLEX_UNKNOWN;
@@ -295,6 +293,8 @@
 	port = nfp_port_from_netdev(netdev);
 	eth_port = nfp_port_get_eth_port(port);
 	if (eth_port) {
+		ethtool_link_ksettings_add_link_mode(cmd, supported, Pause);
+		ethtool_link_ksettings_add_link_mode(cmd, advertising, Pause);
 		cmd->base.autoneg = eth_port->aneg != NFP_ANEG_DISABLED ?
 			AUTONEG_ENABLE : AUTONEG_DISABLE;
 		nfp_net_set_fec_link_mode(eth_port, cmd);
@@ -483,7 +483,7 @@
 		unsigned int start;
 
 		do {
-			start = u64_stats_fetch_begin(&nn->r_vecs[i].rx_sync);
+			start = u64_stats_fetch_begin_irq(&nn->r_vecs[i].rx_sync);
 			data[0] = nn->r_vecs[i].rx_pkts;
 			tmp[0] = nn->r_vecs[i].hw_csum_rx_ok;
 			tmp[1] = nn->r_vecs[i].hw_csum_rx_inner_ok;
@@ -491,10 +491,10 @@
 			tmp[3] = nn->r_vecs[i].hw_csum_rx_error;
 			tmp[4] = nn->r_vecs[i].rx_replace_buf_alloc_fail;
 			tmp[5] = nn->r_vecs[i].hw_tls_rx;
-		} while (u64_stats_fetch_retry(&nn->r_vecs[i].rx_sync, start));
+		} while (u64_stats_fetch_retry_irq(&nn->r_vecs[i].rx_sync, start));
 
 		do {
-			start = u64_stats_fetch_begin(&nn->r_vecs[i].tx_sync);
+			start = u64_stats_fetch_begin_irq(&nn->r_vecs[i].tx_sync);
 			data[1] = nn->r_vecs[i].tx_pkts;
 			data[2] = nn->r_vecs[i].tx_busy;
 			tmp[6] = nn->r_vecs[i].hw_csum_tx;
@@ -504,7 +504,7 @@
 			tmp[10] = nn->r_vecs[i].hw_tls_tx;
 			tmp[11] = nn->r_vecs[i].tls_tx_fallback;
 			tmp[12] = nn->r_vecs[i].tls_tx_no_fallback;
-		} while (u64_stats_fetch_retry(&nn->r_vecs[i].tx_sync, start));
+		} while (u64_stats_fetch_retry_irq(&nn->r_vecs[i].tx_sync, start));
 
 		data += NN_RVEC_PER_Q_STATS;
 
@@ -1219,6 +1219,11 @@
 	u8 data;
 
 	port = nfp_port_from_netdev(netdev);
+	if (!port)
+		return -EOPNOTSUPP;
+
+	/* update port state to get latest interface */
+	set_bit(NFP_PORT_CHANGED, &port->flags);
 	eth_port = nfp_port_get_eth_port(port);
 	if (!eth_port)
 		return -EOPNOTSUPP;
@@ -1262,15 +1267,15 @@
 
 		if (data < 0x3) {
 			modinfo->type = ETH_MODULE_SFF_8436;
-			modinfo->eeprom_len = ETH_MODULE_SFF_8436_LEN;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8436_MAX_LEN;
 		} else {
 			modinfo->type = ETH_MODULE_SFF_8636;
-			modinfo->eeprom_len = ETH_MODULE_SFF_8636_LEN;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8636_MAX_LEN;
 		}
 		break;
 	case NFP_INTERFACE_QSFP28:
 		modinfo->type = ETH_MODULE_SFF_8636;
-		modinfo->eeprom_len = ETH_MODULE_SFF_8636_LEN;
+		modinfo->eeprom_len = ETH_MODULE_SFF_8636_MAX_LEN;
 		break;
 	default:
 		netdev_err(netdev, "Unsupported module 0x%x detected\n",
@@ -1343,7 +1348,7 @@
 	 * ME timestamp ticks.  There are 16 ME clock cycles for each timestamp
 	 * count.
 	 */
-	factor = nn->me_freq_mhz / 16;
+	factor = nn->tlv_caps.me_freq_mhz / 16;
 
 	/* Each pair of (usecs, max_frames) fields specifies that interrupts
 	 * should be coalesced until
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfp_net_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfp_net_main.c
@@ -55,7 +55,7 @@
 		return;
 	}
 
-	ether_addr_copy(netdev->dev_addr, eth_port->mac_addr);
+	eth_hw_addr_set(netdev, eth_port->mac_addr);
 	ether_addr_copy(netdev->perm_addr, eth_port->mac_addr);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfp_netvf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfp_netvf_main.c
@@ -58,7 +58,7 @@
 		return;
 	}
 
-	ether_addr_copy(nn->dp.netdev->dev_addr, mac_addr);
+	eth_hw_addr_set(nn->dp.netdev, mac_addr);
 	ether_addr_copy(nn->dp.netdev->perm_addr, mac_addr);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c
@@ -542,11 +542,13 @@
 	const u32 barcfg_msix_general =
 		NFP_PCIE_BAR_PCIE2CPP_MapType(
 			NFP_PCIE_BAR_PCIE2CPP_MapType_GENERAL) |
-		NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT;
+		NFP_PCIE_BAR_PCIE2CPP_LengthSelect(
+			NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT);
 	const u32 barcfg_msix_xpb =
 		NFP_PCIE_BAR_PCIE2CPP_MapType(
 			NFP_PCIE_BAR_PCIE2CPP_MapType_BULK) |
-		NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT |
+		NFP_PCIE_BAR_PCIE2CPP_LengthSelect(
+			NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT) |
 		NFP_PCIE_BAR_PCIE2CPP_Target_BaseAddress(
 			NFP_CPP_TARGET_ISLAND_XPB);
 	const u32 barcfg_explicit[4] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c
@@ -803,8 +803,10 @@
 		return -ENOMEM;
 
 	cache = kzalloc(sizeof(*cache), GFP_KERNEL);
-	if (!cache)
+	if (!cache) {
+		nfp_cpp_area_free(area);
 		return -ENOMEM;
+	}
 
 	cache->id = 0;
 	cache->addr = 0;
@@ -872,7 +874,6 @@
 	}
 
 	/* Adjust the start address to be cache size aligned */
-	cache->id = id;
 	cache->addr = addr & ~(u64)(cache->size - 1);
 
 	/* Re-init to the new ID and address */
@@ -892,6 +893,8 @@
 		return NULL;
 	}
 
+	cache->id = id;
+
 exit:
 	/* Adjust offset */
 	*offset = addr - cache->addr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ni/nixge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ni/nixge.c
@@ -249,25 +249,26 @@
 	struct sk_buff *skb;
 	int i;
 
-	for (i = 0; i < RX_BD_NUM; i++) {
-		phys_addr = nixge_hw_dma_bd_get_addr(&priv->rx_bd_v[i],
-						     phys);
-
-		dma_unmap_single(ndev->dev.parent, phys_addr,
-				 NIXGE_MAX_JUMBO_FRAME_SIZE,
-				 DMA_FROM_DEVICE);
-
-		skb = (struct sk_buff *)(uintptr_t)
-			nixge_hw_dma_bd_get_addr(&priv->rx_bd_v[i],
-						 sw_id_offset);
-		dev_kfree_skb(skb);
-	}
+	if (priv->rx_bd_v) {
+		for (i = 0; i < RX_BD_NUM; i++) {
+			phys_addr = nixge_hw_dma_bd_get_addr(&priv->rx_bd_v[i],
+							     phys);
+
+			dma_unmap_single(ndev->dev.parent, phys_addr,
+					 NIXGE_MAX_JUMBO_FRAME_SIZE,
+					 DMA_FROM_DEVICE);
+
+			skb = (struct sk_buff *)(uintptr_t)
+				nixge_hw_dma_bd_get_addr(&priv->rx_bd_v[i],
+							 sw_id_offset);
+			dev_kfree_skb(skb);
+		}
 
-	if (priv->rx_bd_v)
 		dma_free_coherent(ndev->dev.parent,
 				  sizeof(*priv->rx_bd_v) * RX_BD_NUM,
 				  priv->rx_bd_v,
 				  priv->rx_bd_p);
+	}
 
 	if (priv->tx_skb)
 		devm_kfree(ndev->dev.parent, priv->tx_skb);
@@ -899,6 +900,7 @@
 err_rx_irq:
 	free_irq(priv->tx_irq, ndev);
 err_tx_irq:
+	napi_disable(&priv->napi);
 	phy_stop(phy);
 	phy_disconnect(phy);
 	tasklet_kill(&priv->dma_err_tasklet);
@@ -1209,7 +1211,7 @@
 
 	cell = nvmem_cell_get(dev, "address");
 	if (IS_ERR(cell))
-		return NULL;
+		return cell;
 
 	mac = nvmem_cell_read(cell, &cell_size);
 	nvmem_cell_put(cell);
@@ -1282,8 +1284,8 @@
 	ndev->max_mtu = NIXGE_JUMBO_MTU;
 
 	mac_addr = nixge_get_nvmem_address(&pdev->dev);
-	if (mac_addr && is_valid_ether_addr(mac_addr)) {
-		ether_addr_copy(ndev->dev_addr, mac_addr);
+	if (!IS_ERR(mac_addr) && is_valid_ether_addr(mac_addr)) {
+		eth_hw_addr_set(ndev, mac_addr);
 		kfree(mac_addr);
 	} else {
 		eth_hw_addr_random(ndev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/nvidia/forcedeth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/nvidia/forcedeth.c
@@ -56,8 +56,8 @@
 
 #include <asm/irq.h>
 
-#define TX_WORK_PER_LOOP  64
-#define RX_WORK_PER_LOOP  64
+#define TX_WORK_PER_LOOP  NAPI_POLL_WEIGHT
+#define RX_WORK_PER_LOOP  NAPI_POLL_WEIGHT
 
 /*
  * Hardware access:
@@ -5869,7 +5869,7 @@
 	else
 		dev->netdev_ops = &nv_netdev_ops_optimized;
 
-	netif_napi_add(dev, &np->napi, nv_napi_poll, RX_WORK_PER_LOOP);
+	netif_napi_add(dev, &np->napi, nv_napi_poll, NAPI_POLL_WEIGHT);
 	dev->ethtool_ops = &ops;
 	dev->watchdog_timeo = NV_WATCHDOG_TIMEO;
 
@@ -6129,6 +6129,7 @@
 	return 0;
 
 out_error:
+	nv_mgmt_release_sema(dev);
 	if (phystate_orig)
 		writel(phystate|NVREG_ADAPTCTL_RUNNING, base + NvRegAdapterControl);
 out_freering:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/nxp/lpc_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/nxp/lpc_eth.c
@@ -419,7 +419,7 @@
 /*
  * MAC support functions
  */
-static void __lpc_set_mac(struct netdata_local *pldat, u8 *mac)
+static void __lpc_set_mac(struct netdata_local *pldat, const u8 *mac)
 {
 	u32 tmp;
 
@@ -1349,7 +1349,7 @@
 	__lpc_get_mac(pldat, ndev->dev_addr);
 
 	if (!is_valid_ether_addr(ndev->dev_addr)) {
-		of_get_mac_address(np, ndev->dev_addr);
+		of_get_ethdev_address(np, ndev);
 	}
 	if (!is_valid_ether_addr(ndev->dev_addr))
 		eth_hw_addr_random(ndev);
@@ -1469,6 +1469,7 @@
 {
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct netdata_local *pldat;
+	int ret;
 
 	if (device_may_wakeup(&pdev->dev))
 		disable_irq_wake(ndev->irq);
@@ -1478,7 +1479,9 @@
 			pldat = netdev_priv(ndev);
 
 			/* Enable interface clock */
-			clk_enable(pldat->clk);
+			ret = clk_enable(pldat->clk);
+			if (ret)
+				return ret;
 
 			/* Reset and initialize */
 			__lpc_eth_reset(pldat);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
@@ -1148,6 +1148,7 @@
 		buffer_info->dma = 0;
 		buffer_info->time_stamp = 0;
 		tx_ring->next_to_use = ring_num;
+		dev_kfree_skb_any(skb);
 		return;
 	}
 	buffer_info->mapped = true;
@@ -2464,6 +2465,7 @@
 	unregister_netdev(netdev);
 
 	pch_gbe_phy_hw_reset(&adapter->hw);
+	pci_dev_put(adapter->ptp_pdev);
 
 	free_netdev(netdev);
 }
@@ -2539,7 +2541,7 @@
 	/* setup the private structure */
 	ret = pch_gbe_sw_init(adapter);
 	if (ret)
-		goto err_free_netdev;
+		goto err_put_dev;
 
 	/* Initialize PHY */
 	ret = pch_gbe_init_phy(adapter);
@@ -2597,6 +2599,8 @@
 
 err_free_adapter:
 	pch_gbe_phy_hw_reset(&adapter->hw);
+err_put_dev:
+	pci_dev_put(adapter->ptp_pdev);
 err_free_netdev:
 	free_netdev(netdev);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pasemi/pasemi_mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pasemi/pasemi_mac.c
@@ -1423,7 +1423,7 @@
 	write_dma_reg(PAS_DMA_TXCHAN_INCR(txring->chan.chno), 2);
 }
 
-static int pasemi_mac_start_tx(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t pasemi_mac_start_tx(struct sk_buff *skb, struct net_device *dev)
 {
 	struct pasemi_mac * const mac = netdev_priv(dev);
 	struct pasemi_mac_txring * const txring = tx_ring(mac);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_bus_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_bus_pci.c
@@ -255,7 +255,7 @@
 
 	err = ionic_map_bars(ionic);
 	if (err)
-		goto err_out_pci_disable_device;
+		goto err_out_pci_release_regions;
 
 	/* Configure the device */
 	err = ionic_setup(ionic);
@@ -331,6 +331,9 @@
 		goto err_out_deregister_lifs;
 	}
 
+	mod_timer(&ionic->watchdog_timer,
+		  round_jiffies(jiffies + ionic->watchdog_period));
+
 	return 0;
 
 err_out_deregister_lifs:
@@ -348,7 +351,6 @@
 err_out_reset:
 	ionic_reset(ionic);
 err_out_teardown:
-	del_timer_sync(&ionic->watchdog_timer);
 	pci_clear_master(pdev);
 	/* Don't fail the probe for these errors, keep
 	 * the hw interface around for inspection
@@ -357,6 +359,7 @@
 
 err_out_unmap_bars:
 	ionic_unmap_bars(ionic);
+err_out_pci_release_regions:
 	pci_release_regions(pdev);
 err_out_pci_disable_device:
 	pci_disable_device(pdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_dev.c
@@ -122,9 +122,6 @@
 	idev->fw_generation = IONIC_FW_STS_F_GENERATION &
 			      ioread8(&idev->dev_info_regs->fw_status);
 
-	mod_timer(&ionic->watchdog_timer,
-		  round_jiffies(jiffies + ionic->watchdog_period));
-
 	idev->db_pages = bar->vaddr;
 	idev->phy_db_pages = bar->bus_addr;
 
@@ -132,6 +129,16 @@
 }
 
 /* Devcmd Interface */
+bool ionic_is_fw_running(struct ionic_dev *idev)
+{
+	u8 fw_status = ioread8(&idev->dev_info_regs->fw_status);
+
+	/* firmware is useful only if the running bit is set and
+	 * fw_status != 0xff (bad PCI read)
+	 */
+	return (fw_status != 0xff) && (fw_status & IONIC_FW_STS_F_RUNNING);
+}
+
 int ionic_heartbeat_check(struct ionic *ionic)
 {
 	struct ionic_dev *idev = &ionic->idev;
@@ -155,13 +162,10 @@
 		goto do_check_time;
 	}
 
-	/* firmware is useful only if the running bit is set and
-	 * fw_status != 0xff (bad PCI read)
-	 * If fw_status is not ready don't bother with the generation.
-	 */
 	fw_status = ioread8(&idev->dev_info_regs->fw_status);
 
-	if (fw_status == 0xff || !(fw_status & IONIC_FW_STS_F_RUNNING)) {
+	/* If fw_status is not ready don't bother with the generation */
+	if (!ionic_is_fw_running(idev)) {
 		fw_status_ready = false;
 	} else {
 		fw_generation = fw_status & IONIC_FW_STS_F_GENERATION;
@@ -264,6 +268,7 @@
 
 void ionic_dev_cmd_go(struct ionic_dev *idev, union ionic_dev_cmd *cmd)
 {
+	idev->opcode = cmd->cmd.opcode;
 	memcpy_toio(&idev->dev_cmd_regs->cmd, cmd, sizeof(*cmd));
 	iowrite32(0, &idev->dev_cmd_regs->done);
 	iowrite32(1, &idev->dev_cmd_regs->doorbell);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_dev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_dev.h
@@ -144,6 +144,7 @@
 	bool fw_hb_ready;
 	bool fw_status_ready;
 	u8 fw_generation;
+	u8 opcode;
 
 	u64 __iomem *db_pages;
 	dma_addr_t phy_db_pages;
@@ -174,6 +175,7 @@
 			      struct ionic_desc_info *desc_info,
 			      struct ionic_cq_info *cq_info, void *cb_arg);
 
+#define IONIC_MAX_BUF_LEN			((u16)-1)
 #define IONIC_PAGE_SIZE				PAGE_SIZE
 #define IONIC_PAGE_SPLIT_SZ			(PAGE_SIZE / 2)
 #define IONIC_PAGE_GFP_MASK			(GFP_ATOMIC | __GFP_NOWARN |\
@@ -207,7 +209,7 @@
 	void *cb_arg;
 };
 
-#define IONIC_QUEUE_NAME_MAX_SZ		32
+#define IONIC_QUEUE_NAME_MAX_SZ		16
 
 struct ionic_queue {
 	struct device *dev;
@@ -357,5 +359,6 @@
 void ionic_q_service(struct ionic_queue *q, struct ionic_cq_info *cq_info,
 		     unsigned int stop_index);
 int ionic_heartbeat_check(struct ionic *ionic);
+bool ionic_is_fw_running(struct ionic_dev *idev);
 
 #endif /* _IONIC_DEV_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_devlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_devlink.c
@@ -65,6 +65,8 @@
 	struct devlink *dl;
 
 	dl = devlink_alloc(&ionic_dl_ops, sizeof(struct ionic), dev);
+	if (!dl)
+		return NULL;
 
 	return devlink_priv(dl);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_ethtool.c
@@ -724,7 +724,7 @@
 		info->data = lif->nxqs;
 		break;
 	default:
-		netdev_err(netdev, "Command parameter %d is not supported\n",
+		netdev_dbg(netdev, "Command parameter %d is not supported\n",
 			   info->cmd);
 		err = -EOPNOTSUPP;
 	}
@@ -861,8 +861,8 @@
 	len = min_t(u32, sizeof(xcvr->sprom), ee->len);
 
 	do {
-		memcpy(data, xcvr->sprom, len);
-		memcpy(tbuf, xcvr->sprom, len);
+		memcpy(data, &xcvr->sprom[ee->offset], len);
+		memcpy(tbuf, &xcvr->sprom[ee->offset], len);
 
 		/* Let's make sure we got a consistent copy */
 		if (!memcmp(data, tbuf, len))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_lif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_lif.c
@@ -44,24 +44,24 @@
 static void ionic_dim_work(struct work_struct *work)
 {
 	struct dim *dim = container_of(work, struct dim, work);
+	struct ionic_intr_info *intr;
 	struct dim_cq_moder cur_moder;
 	struct ionic_qcq *qcq;
+	struct ionic_lif *lif;
 	u32 new_coal;
 
 	cur_moder = net_dim_get_rx_moderation(dim->mode, dim->profile_ix);
 	qcq = container_of(dim, struct ionic_qcq, dim);
-	new_coal = ionic_coal_usec_to_hw(qcq->q.lif->ionic, cur_moder.usec);
+	lif = qcq->q.lif;
+	new_coal = ionic_coal_usec_to_hw(lif->ionic, cur_moder.usec);
 	new_coal = new_coal ? new_coal : 1;
 
-	if (qcq->intr.dim_coal_hw != new_coal) {
-		unsigned int qi = qcq->cq.bound_q->index;
-		struct ionic_lif *lif = qcq->q.lif;
-
-		qcq->intr.dim_coal_hw = new_coal;
+	intr = &qcq->intr;
+	if (intr->dim_coal_hw != new_coal) {
+		intr->dim_coal_hw = new_coal;
 
 		ionic_intr_coal_init(lif->ionic->idev.intr_ctrl,
-				     lif->rxqcqs[qi]->intr.index,
-				     qcq->intr.dim_coal_hw);
+				     intr->index, intr->dim_coal_hw);
 	}
 
 	dim->state = DIM_START_MEASURE;
@@ -221,7 +221,7 @@
 		name = dev_name(dev);
 
 	snprintf(intr->name, sizeof(intr->name),
-		 "%s-%s-%s", IONIC_DRV_NAME, name, q->name);
+		 "%.5s-%.16s-%.8s", IONIC_DRV_NAME, name, q->name);
 
 	return devm_request_irq(dev, intr->vector, ionic_isr,
 				0, intr->name, &qcq->napi);
@@ -268,6 +268,7 @@
 			.oper = IONIC_Q_ENABLE,
 		},
 	};
+	int ret;
 
 	idev = &lif->ionic->idev;
 	dev = lif->ionic->dev;
@@ -275,16 +276,22 @@
 	dev_dbg(dev, "q_enable.index %d q_enable.qtype %d\n",
 		ctx.cmd.q_control.index, ctx.cmd.q_control.type);
 
+	if (qcq->flags & IONIC_QCQ_F_INTR)
+		ionic_intr_clean(idev->intr_ctrl, qcq->intr.index);
+
+	ret = ionic_adminq_post_wait(lif, &ctx);
+	if (ret)
+		return ret;
+
 	if (qcq->flags & IONIC_QCQ_F_INTR) {
+		napi_enable(&qcq->napi);
 		irq_set_affinity_hint(qcq->intr.vector,
 				      &qcq->intr.affinity_mask);
-		napi_enable(&qcq->napi);
-		ionic_intr_clean(idev->intr_ctrl, qcq->intr.index);
 		ionic_intr_mask(idev->intr_ctrl, qcq->intr.index,
 				IONIC_INTR_MASK_CLEAR);
 	}
 
-	return ionic_adminq_post_wait(lif, &ctx);
+	return 0;
 }
 
 static int ionic_qcq_disable(struct ionic_qcq *qcq, bool send_to_hw)
@@ -442,11 +449,6 @@
 static void ionic_link_qcq_interrupts(struct ionic_qcq *src_qcq,
 				      struct ionic_qcq *n_qcq)
 {
-	if (WARN_ON(n_qcq->flags & IONIC_QCQ_F_INTR)) {
-		ionic_intr_free(n_qcq->cq.lif->ionic, n_qcq->intr.index);
-		n_qcq->flags &= ~IONIC_QCQ_F_INTR;
-	}
-
 	n_qcq->intr.vector = src_qcq->intr.vector;
 	n_qcq->intr.index = src_qcq->intr.index;
 }
@@ -1565,7 +1567,7 @@
 	if ((old_hw_features ^ lif->hw_features) & IONIC_ETH_HW_RX_HASH)
 		ionic_lif_rss_config(lif, lif->rss_types, NULL, NULL);
 
-	if ((vlan_flags & features) &&
+	if ((vlan_flags & le64_to_cpu(ctx.cmd.lif_setattr.features)) &&
 	    !(vlan_flags & le64_to_cpu(ctx.comp.lif_setattr.features)))
 		dev_info_once(lif->ionic->dev, "NIC is not supporting vlan offload, likely in SmartNIC mode\n");
 
@@ -1692,8 +1694,67 @@
 	return err;
 }
 
+static int ionic_set_attr_mac(struct ionic_lif *lif, u8 *mac)
+{
+	struct ionic_admin_ctx ctx = {
+		.work = COMPLETION_INITIALIZER_ONSTACK(ctx.work),
+		.cmd.lif_setattr = {
+			.opcode = IONIC_CMD_LIF_SETATTR,
+			.index = cpu_to_le16(lif->index),
+			.attr = IONIC_LIF_ATTR_MAC,
+		},
+	};
+
+	ether_addr_copy(ctx.cmd.lif_setattr.mac, mac);
+	return ionic_adminq_post_wait(lif, &ctx);
+}
+
+static int ionic_get_attr_mac(struct ionic_lif *lif, u8 *mac_addr)
+{
+	struct ionic_admin_ctx ctx = {
+		.work = COMPLETION_INITIALIZER_ONSTACK(ctx.work),
+		.cmd.lif_getattr = {
+			.opcode = IONIC_CMD_LIF_GETATTR,
+			.index = cpu_to_le16(lif->index),
+			.attr = IONIC_LIF_ATTR_MAC,
+		},
+	};
+	int err;
+
+	err = ionic_adminq_post_wait(lif, &ctx);
+	if (err)
+		return err;
+
+	ether_addr_copy(mac_addr, ctx.comp.lif_getattr.mac);
+	return 0;
+}
+
+static int ionic_program_mac(struct ionic_lif *lif, u8 *mac)
+{
+	u8  get_mac[ETH_ALEN];
+	int err;
+
+	err = ionic_set_attr_mac(lif, mac);
+	if (err)
+		return err;
+
+	err = ionic_get_attr_mac(lif, get_mac);
+	if (err)
+		return err;
+
+	/* To deal with older firmware that silently ignores the set attr mac:
+	 * doesn't actually change the mac and doesn't return an error, so we
+	 * do the get attr to verify whether or not the set actually happened
+	 */
+	if (!ether_addr_equal(get_mac, mac))
+		return 1;
+
+	return 0;
+}
+
 static int ionic_set_mac_address(struct net_device *netdev, void *sa)
 {
+	struct ionic_lif *lif = netdev_priv(netdev);
 	struct sockaddr *addr = sa;
 	u8 *mac;
 	int err;
@@ -1702,6 +1763,14 @@
 	if (ether_addr_equal(netdev->dev_addr, mac))
 		return 0;
 
+	err = ionic_program_mac(lif, mac);
+	if (err < 0)
+		return err;
+
+	if (err > 0)
+		netdev_dbg(netdev, "%s: SET and GET ATTR Mac are not equal-due to old FW running\n",
+			   __func__);
+
 	err = eth_prepare_mac_addr_change(netdev, addr);
 	if (err)
 		return err;
@@ -2813,11 +2882,15 @@
 	 * than the full array, but leave the qcq shells in place
 	 */
 	for (i = lif->nxqs; i < lif->ionic->ntxqs_per_lif; i++) {
-		lif->txqcqs[i]->flags &= ~IONIC_QCQ_F_INTR;
-		ionic_qcq_free(lif, lif->txqcqs[i]);
+		if (lif->txqcqs && lif->txqcqs[i]) {
+			lif->txqcqs[i]->flags &= ~IONIC_QCQ_F_INTR;
+			ionic_qcq_free(lif, lif->txqcqs[i]);
+		}
 
-		lif->rxqcqs[i]->flags &= ~IONIC_QCQ_F_INTR;
-		ionic_qcq_free(lif, lif->rxqcqs[i]);
+		if (lif->rxqcqs && lif->rxqcqs[i]) {
+			lif->rxqcqs[i]->flags &= ~IONIC_QCQ_F_INTR;
+			ionic_qcq_free(lif, lif->rxqcqs[i]);
+		}
 	}
 
 	if (err)
@@ -2974,11 +3047,10 @@
 
 	netif_device_detach(lif->netdev);
 
+	mutex_lock(&lif->queue_lock);
 	if (test_bit(IONIC_LIF_F_UP, lif->state)) {
 		dev_info(ionic->dev, "Surprise FW stop, stopping queues\n");
-		mutex_lock(&lif->queue_lock);
 		ionic_stop_queues(lif);
-		mutex_unlock(&lif->queue_lock);
 	}
 
 	if (netif_running(lif->netdev)) {
@@ -2989,6 +3061,8 @@
 	ionic_reset(ionic);
 	ionic_qcqs_free(lif);
 
+	mutex_unlock(&lif->queue_lock);
+
 	dev_info(ionic->dev, "FW Down: LIFs stopped\n");
 }
 
@@ -3012,9 +3086,15 @@
 	err = ionic_port_init(ionic);
 	if (err)
 		goto err_out;
+
+	mutex_lock(&lif->queue_lock);
+
+	if (test_and_clear_bit(IONIC_LIF_F_BROKEN, lif->state))
+		dev_info(ionic->dev, "FW Up: clearing broken state\n");
+
 	err = ionic_qcqs_alloc(lif);
 	if (err)
-		goto err_out;
+		goto err_unlock;
 
 	err = ionic_lif_init(lif);
 	if (err)
@@ -3035,6 +3115,8 @@
 			goto err_txrx_free;
 	}
 
+	mutex_unlock(&lif->queue_lock);
+
 	clear_bit(IONIC_LIF_F_FW_RESET, lif->state);
 	ionic_link_status_check_request(lif, CAN_SLEEP);
 	netif_device_attach(lif->netdev);
@@ -3051,6 +3133,8 @@
 	ionic_lif_deinit(lif);
 err_qcqs_free:
 	ionic_qcqs_free(lif);
+err_unlock:
+	mutex_unlock(&lif->queue_lock);
 err_out:
 	dev_err(ionic->dev, "FW Up: LIFs restart failed - err %d\n", err);
 }
@@ -3146,9 +3230,12 @@
 
 	napi_enable(&qcq->napi);
 
-	if (qcq->flags & IONIC_QCQ_F_INTR)
+	if (qcq->flags & IONIC_QCQ_F_INTR) {
+		irq_set_affinity_hint(qcq->intr.vector,
+				      &qcq->intr.affinity_mask);
 		ionic_intr_mask(idev->intr_ctrl, qcq->intr.index,
 				IONIC_INTR_MASK_CLEAR);
+	}
 
 	qcq->flags |= IONIC_QCQ_F_INITED;
 
@@ -3215,6 +3302,7 @@
 			.attr = IONIC_LIF_ATTR_MAC,
 		},
 	};
+	u8 mac_address[ETH_ALEN];
 	struct sockaddr addr;
 	int err;
 
@@ -3223,8 +3311,23 @@
 		return err;
 	netdev_dbg(lif->netdev, "found initial MAC addr %pM\n",
 		   ctx.comp.lif_getattr.mac);
-	if (is_zero_ether_addr(ctx.comp.lif_getattr.mac))
-		return 0;
+	ether_addr_copy(mac_address, ctx.comp.lif_getattr.mac);
+
+	if (is_zero_ether_addr(mac_address)) {
+		eth_hw_addr_random(netdev);
+		netdev_dbg(netdev, "Random Mac generated: %pM\n", netdev->dev_addr);
+		ether_addr_copy(mac_address, netdev->dev_addr);
+
+		err = ionic_program_mac(lif, mac_address);
+		if (err < 0)
+			return err;
+
+		if (err > 0) {
+			netdev_dbg(netdev, "%s:SET/GET ATTR Mac are not same-due to old FW running\n",
+				   __func__);
+			return 0;
+		}
+	}
 
 	if (!is_zero_ether_addr(netdev->dev_addr)) {
 		/* If the netdev mac is non-zero and doesn't match the default
@@ -3232,12 +3335,11 @@
 		 * likely here again after a fw-upgrade reset.  We need to be
 		 * sure the netdev mac is in our filter list.
 		 */
-		if (!ether_addr_equal(ctx.comp.lif_getattr.mac,
-				      netdev->dev_addr))
+		if (!ether_addr_equal(mac_address, netdev->dev_addr))
 			ionic_lif_addr_add(lif, netdev->dev_addr);
 	} else {
 		/* Update the netdev mac with the device's mac */
-		memcpy(addr.sa_data, ctx.comp.lif_getattr.mac, netdev->addr_len);
+		ether_addr_copy(addr.sa_data, mac_address);
 		addr.sa_family = AF_INET;
 		err = eth_prepare_mac_addr_change(netdev, &addr);
 		if (err) {
@@ -3283,7 +3385,7 @@
 		return -EINVAL;
 	}
 
-	lif->dbid_inuse = bitmap_alloc(lif->dbid_count, GFP_KERNEL);
+	lif->dbid_inuse = bitmap_zalloc(lif->dbid_count, GFP_KERNEL);
 	if (!lif->dbid_inuse) {
 		dev_err(dev, "Failed alloc doorbell id bitmap, aborting\n");
 		return -ENOMEM;
@@ -3412,8 +3514,8 @@
 	/* only register LIF0 for now */
 	err = register_netdev(lif->netdev);
 	if (err) {
-		dev_err(lif->ionic->dev, "Cannot register net device, aborting\n");
-		ionic_lif_unregister_phc(lif);
+		dev_err(lif->ionic->dev, "Cannot register net device: %d, aborting\n", err);
+		ionic_lif_unregister(lif);
 		return err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_main.c
@@ -328,10 +328,10 @@
 
 static void ionic_dev_cmd_clean(struct ionic *ionic)
 {
-	union __iomem ionic_dev_cmd_regs *regs = ionic->idev.dev_cmd_regs;
+	struct ionic_dev *idev = &ionic->idev;
 
-	iowrite32(0, &regs->doorbell);
-	memset_io(&regs->cmd, 0, sizeof(regs->cmd));
+	iowrite32(0, &idev->dev_cmd_regs->doorbell);
+	memset_io(&idev->dev_cmd_regs->cmd, 0, sizeof(idev->dev_cmd_regs->cmd));
 }
 
 int ionic_dev_cmd_wait(struct ionic *ionic, unsigned long max_seconds)
@@ -350,7 +350,7 @@
 	 */
 	max_wait = jiffies + (max_seconds * HZ);
 try_again:
-	opcode = readb(&idev->dev_cmd_regs->cmd.cmd.opcode);
+	opcode = idev->opcode;
 	start_time = jiffies;
 	do {
 		done = ionic_dev_cmd_done(idev);
@@ -395,8 +395,8 @@
 				ionic_opcode_to_str(opcode), opcode,
 				ionic_error_to_str(err), err);
 
-			msleep(1000);
 			iowrite32(0, &idev->dev_cmd_regs->done);
+			msleep(1000);
 			iowrite32(1, &idev->dev_cmd_regs->doorbell);
 			goto try_again;
 		}
@@ -409,6 +409,8 @@
 		return ionic_error_to_errno(err);
 	}
 
+	ionic_dev_cmd_clean(ionic);
+
 	return 0;
 }
 
@@ -488,6 +490,9 @@
 	struct ionic_dev *idev = &ionic->idev;
 	int err;
 
+	if (!ionic_is_fw_running(idev))
+		return 0;
+
 	mutex_lock(&ionic->dev_cmd_lock);
 	ionic_dev_cmd_reset(idev);
 	err = ionic_dev_cmd_wait(ionic, DEVCMD_TIMEOUT);
@@ -560,15 +565,17 @@
 int ionic_port_reset(struct ionic *ionic)
 {
 	struct ionic_dev *idev = &ionic->idev;
-	int err;
+	int err = 0;
 
 	if (!idev->port_info)
 		return 0;
 
-	mutex_lock(&ionic->dev_cmd_lock);
-	ionic_dev_cmd_port_reset(idev);
-	err = ionic_dev_cmd_wait(ionic, DEVCMD_TIMEOUT);
-	mutex_unlock(&ionic->dev_cmd_lock);
+	if (ionic_is_fw_running(idev)) {
+		mutex_lock(&ionic->dev_cmd_lock);
+		ionic_dev_cmd_port_reset(idev);
+		err = ionic_dev_cmd_wait(ionic, DEVCMD_TIMEOUT);
+		mutex_unlock(&ionic->dev_cmd_lock);
+	}
 
 	dma_free_coherent(ionic->dev, idev->port_info_sz,
 			  idev->port_info, idev->port_info_pa);
@@ -576,16 +583,19 @@
 	idev->port_info = NULL;
 	idev->port_info_pa = 0;
 
-	if (err)
-		dev_err(ionic->dev, "Failed to reset port\n");
-
 	return err;
 }
 
 static int __init ionic_init_module(void)
 {
+	int ret;
+
 	ionic_debugfs_create();
-	return ionic_bus_register_driver();
+	ret = ionic_bus_register_driver();
+	if (ret)
+		ionic_debugfs_destroy();
+
+	return ret;
 }
 
 static void __exit ionic_cleanup_module(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/pensando/ionic/ionic_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/pensando/ionic/ionic_txrx.c
@@ -151,7 +151,8 @@
 			return NULL;
 		}
 
-		frag_len = min_t(u16, len, IONIC_PAGE_SIZE - buf_info->page_offset);
+		frag_len = min_t(u16, len, min_t(u32, IONIC_MAX_BUF_LEN,
+						 IONIC_PAGE_SIZE - buf_info->page_offset));
 		len -= frag_len;
 
 		dma_sync_single_for_cpu(dev,
@@ -353,16 +354,25 @@
 	struct ionic_rxq_sg_desc *sg_desc;
 	struct ionic_rxq_sg_elem *sg_elem;
 	struct ionic_buf_info *buf_info;
+	unsigned int fill_threshold;
 	struct ionic_rxq_desc *desc;
 	unsigned int remain_len;
 	unsigned int frag_len;
 	unsigned int nfrags;
+	unsigned int n_fill;
 	unsigned int i, j;
 	unsigned int len;
 
+	n_fill = ionic_q_space_avail(q);
+
+	fill_threshold = min_t(unsigned int, IONIC_RX_FILL_THRESHOLD,
+			       q->num_descs / IONIC_RX_FILL_DIV);
+	if (n_fill < fill_threshold)
+		return;
+
 	len = netdev->mtu + ETH_HLEN + VLAN_HLEN;
 
-	for (i = ionic_q_space_avail(q); i; i--) {
+	for (i = n_fill; i; i--) {
 		nfrags = 0;
 		remain_len = len;
 		desc_info = &q->info[q->head_idx];
@@ -379,7 +389,8 @@
 
 		/* fill main descriptor - buf[0] */
 		desc->addr = cpu_to_le64(buf_info->dma_addr + buf_info->page_offset);
-		frag_len = min_t(u16, len, IONIC_PAGE_SIZE - buf_info->page_offset);
+		frag_len = min_t(u16, len, min_t(u32, IONIC_MAX_BUF_LEN,
+						 IONIC_PAGE_SIZE - buf_info->page_offset));
 		desc->len = cpu_to_le16(frag_len);
 		remain_len -= frag_len;
 		buf_info++;
@@ -398,7 +409,9 @@
 			}
 
 			sg_elem->addr = cpu_to_le64(buf_info->dma_addr + buf_info->page_offset);
-			frag_len = min_t(u16, remain_len, IONIC_PAGE_SIZE - buf_info->page_offset);
+			frag_len = min_t(u16, remain_len, min_t(u32, IONIC_MAX_BUF_LEN,
+								IONIC_PAGE_SIZE -
+								buf_info->page_offset));
 			sg_elem->len = cpu_to_le16(frag_len);
 			remain_len -= frag_len;
 			buf_info++;
@@ -518,7 +531,6 @@
 	struct ionic_cq *cq = napi_to_cq(napi);
 	struct ionic_dev *idev;
 	struct ionic_lif *lif;
-	u16 rx_fill_threshold;
 	u32 work_done = 0;
 	u32 flags = 0;
 
@@ -528,10 +540,7 @@
 	work_done = ionic_cq_service(cq, budget,
 				     ionic_rx_service, NULL, NULL);
 
-	rx_fill_threshold = min_t(u16, IONIC_RX_FILL_THRESHOLD,
-				  cq->num_descs / IONIC_RX_FILL_DIV);
-	if (work_done && ionic_q_space_avail(cq->bound_q) >= rx_fill_threshold)
-		ionic_rx_fill(cq->bound_q);
+	ionic_rx_fill(cq->bound_q);
 
 	if (work_done < budget && napi_complete_done(napi, work_done)) {
 		ionic_dim_update(qcq, IONIC_LIF_F_RX_DIM_INTR);
@@ -559,7 +568,6 @@
 	struct ionic_dev *idev;
 	struct ionic_lif *lif;
 	struct ionic_cq *txcq;
-	u16 rx_fill_threshold;
 	u32 rx_work_done = 0;
 	u32 tx_work_done = 0;
 	u32 flags = 0;
@@ -574,10 +582,7 @@
 	rx_work_done = ionic_cq_service(rxcq, budget,
 					ionic_rx_service, NULL, NULL);
 
-	rx_fill_threshold = min_t(u16, IONIC_RX_FILL_THRESHOLD,
-				  rxcq->num_descs / IONIC_RX_FILL_DIV);
-	if (rx_work_done && ionic_q_space_avail(rxcq->bound_q) >= rx_fill_threshold)
-		ionic_rx_fill(rxcq->bound_q);
+	ionic_rx_fill(rxcq->bound_q);
 
 	if (rx_work_done < budget && napi_complete_done(napi, rx_work_done)) {
 		ionic_dim_update(qcq, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c
@@ -1861,7 +1861,7 @@
 
 	if (protocol == cpu_to_be16(ETH_P_8021Q)) {
 
-		vh = (struct vlan_ethhdr *)skb->data;
+		vh = skb_vlan_eth_hdr(skb);
 		protocol = vh->h_vlan_encapsulated_proto;
 		flags = FLAGS_VLAN_TAGGED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed.h
@@ -877,12 +877,13 @@
 
 
 /**
- * @brief qed_concrete_to_sw_fid - get the sw function id from
- *        the concrete value.
+ * qed_concrete_to_sw_fid(): Get the sw function id from
+ *                           the concrete value.
  *
- * @param concrete_fid
+ * @cdev: Qed dev pointer.
+ * @concrete_fid: Concrete fid.
  *
- * @return inline u8
+ * Return: inline u8.
  */
 static inline u8 qed_concrete_to_sw_fid(struct qed_dev *cdev,
 					u32 concrete_fid)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_cxt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_cxt.c
@@ -933,6 +933,7 @@
 		p_dma->virt_addr = NULL;
 	}
 	kfree(p_mngr->ilt_shadow);
+	p_mngr->ilt_shadow = NULL;
 }
 
 static int qed_ilt_blk_alloc(struct qed_hwfn *p_hwfn,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_cxt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_cxt.h
@@ -28,24 +28,23 @@
 };
 
 /**
- * @brief qedo_cid_get_cxt_info - Returns the context info for a specific cid
+ * qed_cxt_get_cid_info(): Returns the context info for a specific cidi.
  *
+ * @p_hwfn: HW device data.
+ * @p_info: In/out.
  *
- * @param p_hwfn
- * @param p_info in/out
- *
- * @return int
+ * Return: Int.
  */
 int qed_cxt_get_cid_info(struct qed_hwfn *p_hwfn,
 			 struct qed_cxt_info *p_info);
 
 /**
- * @brief qed_cxt_get_tid_mem_info
+ * qed_cxt_get_tid_mem_info(): Returns the tid mem info.
  *
- * @param p_hwfn
- * @param p_info
+ * @p_hwfn: HW device data.
+ * @p_info: in/out.
  *
- * @return int
+ * Return: int.
  */
 int qed_cxt_get_tid_mem_info(struct qed_hwfn *p_hwfn,
 			     struct qed_tid_mem *p_info);
@@ -64,142 +63,155 @@
 				enum protocol_type type, u32 *vf_cid);
 
 /**
- * @brief qed_cxt_set_pf_params - Set the PF params for cxt init
+ * qed_cxt_set_pf_params(): Set the PF params for cxt init.
+ *
+ * @p_hwfn: HW device data.
+ * @rdma_tasks: Requested maximum.
  *
- * @param p_hwfn
- * @param rdma_tasks - requested maximum
- * @return int
+ * Return: int.
  */
 int qed_cxt_set_pf_params(struct qed_hwfn *p_hwfn, u32 rdma_tasks);
 
 /**
- * @brief qed_cxt_cfg_ilt_compute - compute ILT init parameters
+ * qed_cxt_cfg_ilt_compute(): Compute ILT init parameters.
  *
- * @param p_hwfn
- * @param last_line
+ * @p_hwfn: HW device data.
+ * @last_line: Last_line.
  *
- * @return int
+ * Return: Int
  */
 int qed_cxt_cfg_ilt_compute(struct qed_hwfn *p_hwfn, u32 *last_line);
 
 /**
- * @brief qed_cxt_cfg_ilt_compute_excess - how many lines can be decreased
+ * qed_cxt_cfg_ilt_compute_excess(): How many lines can be decreased.
+ *
+ * @p_hwfn: HW device data.
+ * @used_lines: Used lines.
  *
- * @param p_hwfn
- * @param used_lines
+ * Return: Int.
  */
 u32 qed_cxt_cfg_ilt_compute_excess(struct qed_hwfn *p_hwfn, u32 used_lines);
 
 /**
- * @brief qed_cxt_mngr_alloc - Allocate and init the context manager struct
+ * qed_cxt_mngr_alloc(): Allocate and init the context manager struct.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_cxt_mngr_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_cxt_mngr_free
+ * qed_cxt_mngr_free() - Context manager free.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_cxt_mngr_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_cxt_tables_alloc - Allocate ILT shadow, Searcher T2, acquired map
+ * qed_cxt_tables_alloc(): Allocate ILT shadow, Searcher T2, acquired map.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_cxt_tables_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_cxt_mngr_setup - Reset the acquired CIDs
+ * qed_cxt_mngr_setup(): Reset the acquired CIDs.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  */
 void qed_cxt_mngr_setup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_cxt_hw_init_common - Initailze ILT and DQ, common phase, per path.
- *
+ * qed_cxt_hw_init_common(): Initailze ILT and DQ, common phase, per path.
  *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_cxt_hw_init_common(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_cxt_hw_init_pf - Initailze ILT and DQ, PF phase, per path.
+ * qed_cxt_hw_init_pf(): Initailze ILT and DQ, PF phase, per path.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Void.
  */
 void qed_cxt_hw_init_pf(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_qm_init_pf - Initailze the QM PF phase, per path
+ * qed_qm_init_pf(): Initailze the QM PF phase, per path.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @is_pf_loading: Is pf pending.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param is_pf_loading
+ * Return: Void.
  */
 void qed_qm_init_pf(struct qed_hwfn *p_hwfn,
 		    struct qed_ptt *p_ptt, bool is_pf_loading);
 
 /**
- * @brief Reconfigures QM pf on the fly
+ * qed_qm_reconf(): Reconfigures QM pf on the fly.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int
+ * Return: Int.
  */
 int qed_qm_reconf(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 #define QED_CXT_PF_CID (0xff)
 
 /**
- * @brief qed_cxt_release - Release a cid
+ * qed_cxt_release_cid(): Release a cid.
  *
- * @param p_hwfn
- * @param cid
+ * @p_hwfn: HW device data.
+ * @cid: Cid.
+ *
+ * Return: Void.
  */
 void qed_cxt_release_cid(struct qed_hwfn *p_hwfn, u32 cid);
 
 /**
- * @brief qed_cxt_release - Release a cid belonging to a vf-queue
+ * _qed_cxt_release_cid(): Release a cid belonging to a vf-queue.
+ *
+ * @p_hwfn: HW device data.
+ * @cid: Cid.
+ * @vfid: Engine relative index. QED_CXT_PF_CID if belongs to PF.
  *
- * @param p_hwfn
- * @param cid
- * @param vfid - engine relative index. QED_CXT_PF_CID if belongs to PF
+ * Return: Void.
  */
 void _qed_cxt_release_cid(struct qed_hwfn *p_hwfn, u32 cid, u8 vfid);
 
 /**
- * @brief qed_cxt_acquire - Acquire a new cid of a specific protocol type
+ * qed_cxt_acquire_cid(): Acquire a new cid of a specific protocol type.
  *
- * @param p_hwfn
- * @param type
- * @param p_cid
+ * @p_hwfn: HW device data.
+ * @type: Type.
+ * @p_cid: Pointer cid.
  *
- * @return int
+ * Return: Int.
  */
 int qed_cxt_acquire_cid(struct qed_hwfn *p_hwfn,
 			enum protocol_type type, u32 *p_cid);
 
 /**
- * @brief _qed_cxt_acquire - Acquire a new cid of a specific protocol type
- *                           for a vf-queue
+ * _qed_cxt_acquire_cid(): Acquire a new cid of a specific protocol type
+ *                         for a vf-queue.
  *
- * @param p_hwfn
- * @param type
- * @param p_cid
- * @param vfid - engine relative index. QED_CXT_PF_CID if belongs to PF
+ * @p_hwfn: HW device data.
+ * @type: Type.
+ * @p_cid: Pointer cid.
+ * @vfid: Engine relative index. QED_CXT_PF_CID if belongs to PF.
  *
- * @return int
+ * Return: Int.
  */
 int _qed_cxt_acquire_cid(struct qed_hwfn *p_hwfn,
 			 enum protocol_type type, u32 *p_cid, u8 vfid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_debug.c
@@ -1796,9 +1796,10 @@
 				   u8 split_id)
 {
 	struct dbg_tools_data *dev_data = &p_hwfn->dbg_info;
-	u8 port_id = 0, pf_id = 0, vf_id = 0, fid = 0;
+	u8 port_id = 0, pf_id = 0, vf_id = 0;
 	bool read_using_dmae = false;
 	u32 thresh;
+	u16 fid;
 
 	if (!dump)
 		return len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_dev.c
@@ -951,7 +951,7 @@
 }
 
 int qed_llh_add_mac_filter(struct qed_dev *cdev,
-			   u8 ppfid, u8 mac_addr[ETH_ALEN])
+			   u8 ppfid, const u8 mac_addr[ETH_ALEN])
 {
 	struct qed_hwfn *p_hwfn = QED_LEADING_HWFN(cdev);
 	struct qed_ptt *p_ptt = qed_ptt_acquire(p_hwfn);
@@ -5022,6 +5022,11 @@
 
 	num_vports = p_hwfn->qm_info.num_vports;
 
+	if (num_vports < 2) {
+		DP_NOTICE(p_hwfn, "Unexpected num_vports: %d\n", num_vports);
+		return -EINVAL;
+	}
+
 	/* Accounting for the vports which are configured for WFQ explicitly */
 	for (i = 0; i < num_vports; i++) {
 		u32 tmp_speed;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_dev_api.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_dev_api.h
@@ -15,44 +15,52 @@
 #include "qed_int.h"
 
 /**
- * @brief qed_init_dp - initialize the debug level
+ * qed_init_dp(): Initialize the debug level.
  *
- * @param cdev
- * @param dp_module
- * @param dp_level
+ * @cdev: Qed dev pointer.
+ * @dp_module: Module debug parameter.
+ * @dp_level: Module debug level.
+ *
+ * Return: Void.
  */
 void qed_init_dp(struct qed_dev *cdev,
 		 u32 dp_module,
 		 u8 dp_level);
 
 /**
- * @brief qed_init_struct - initialize the device structure to
- *        its defaults
+ * qed_init_struct(): Initialize the device structure to
+ *                    its defaults.
+ *
+ * @cdev: Qed dev pointer.
  *
- * @param cdev
+ * Return: Void.
  */
 void qed_init_struct(struct qed_dev *cdev);
 
 /**
- * @brief qed_resc_free -
+ * qed_resc_free: Free device resources.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
+ *
+ * Return: Void.
  */
 void qed_resc_free(struct qed_dev *cdev);
 
 /**
- * @brief qed_resc_alloc -
+ * qed_resc_alloc(): Alloc device resources.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_resc_alloc(struct qed_dev *cdev);
 
 /**
- * @brief qed_resc_setup -
+ * qed_resc_setup(): Setup device resources.
+ *
+ * @cdev: Qed dev pointer.
  *
- * @param cdev
+ * Return: Void.
  */
 void qed_resc_setup(struct qed_dev *cdev);
 
@@ -105,94 +113,113 @@
 };
 
 /**
- * @brief qed_hw_init -
+ * qed_hw_init(): Init Qed hardware.
  *
- * @param cdev
- * @param p_params
+ * @cdev: Qed dev pointer.
+ * @p_params: Pointers to params.
  *
- * @return int
+ * Return: Int.
  */
 int qed_hw_init(struct qed_dev *cdev, struct qed_hw_init_params *p_params);
 
 /**
- * @brief qed_hw_timers_stop_all - stop the timers HW block
+ * qed_hw_timers_stop_all(): Stop the timers HW block.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return void
+ * Return: void.
  */
 void qed_hw_timers_stop_all(struct qed_dev *cdev);
 
 /**
- * @brief qed_hw_stop -
+ * qed_hw_stop(): Stop Qed hardware.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: int.
  */
 int qed_hw_stop(struct qed_dev *cdev);
 
 /**
- * @brief qed_hw_stop_fastpath -should be called incase
- *		slowpath is still required for the device,
- *		but fastpath is not.
+ * qed_hw_stop_fastpath(): Should be called incase
+ *		           slowpath is still required for the device,
+ *		           but fastpath is not.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_hw_stop_fastpath(struct qed_dev *cdev);
 
 /**
- * @brief qed_hw_start_fastpath -restart fastpath traffic,
- *		only if hw_stop_fastpath was called
+ * qed_hw_start_fastpath(): Restart fastpath traffic,
+ *		            only if hw_stop_fastpath was called.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_hw_start_fastpath(struct qed_hwfn *p_hwfn);
 
 
 /**
- * @brief qed_hw_prepare -
+ * qed_hw_prepare(): Prepare Qed hardware.
  *
- * @param cdev
- * @param personality - personality to initialize
+ * @cdev: Qed dev pointer.
+ * @personality: Personality to initialize.
  *
- * @return int
+ * Return: Int.
  */
 int qed_hw_prepare(struct qed_dev *cdev,
 		   int personality);
 
 /**
- * @brief qed_hw_remove -
+ * qed_hw_remove(): Remove Qed hardware.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
+ *
+ * Return: Void.
  */
 void qed_hw_remove(struct qed_dev *cdev);
 
 /**
- * @brief qed_ptt_acquire - Allocate a PTT window
+ * qed_ptt_acquire(): Allocate a PTT window.
  *
- * Should be called at the entry point to the driver (at the beginning of an
- * exported function)
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: struct qed_ptt.
  *
- * @return struct qed_ptt
+ * Should be called at the entry point to the driver (at the beginning of an
+ * exported function).
  */
 struct qed_ptt *qed_ptt_acquire(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ptt_release - Release PTT Window
+ * qed_ptt_acquire_context(): Allocate a PTT window honoring the context
+ *			      atomicy.
  *
- * Should be called at the end of a flow - at the end of the function that
- * acquired the PTT.
+ * @p_hwfn: HW device data.
+ * @is_atomic: Hint from the caller - if the func can sleep or not.
  *
+ * Context: The function should not sleep in case is_atomic == true.
+ * Return: struct qed_ptt.
  *
- * @param p_hwfn
- * @param p_ptt
+ * Should be called at the entry point to the driver
+ * (at the beginning of an exported function).
+ */
+struct qed_ptt *qed_ptt_acquire_context(struct qed_hwfn *p_hwfn,
+					bool is_atomic);
+
+/**
+ * qed_ptt_release(): Release PTT Window.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Void.
+ *
+ * Should be called at the end of a flow - at the end of the function that
+ * acquired the PTT.
  */
 void qed_ptt_release(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt);
@@ -205,15 +232,17 @@
 };
 
 /**
- * @brief qed_dmae_host2grc - copy data from source addr to
- * dmae registers using the given ptt
+ * qed_dmae_host2grc(): Copy data from source addr to
+ *                      dmae registers using the given ptt.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @source_addr: Source address.
+ * @grc_addr: GRC address (dmae_data_offset).
+ * @size_in_dwords: Size.
+ * @p_params: (default parameters will be used in case of NULL).
  *
- * @param p_hwfn
- * @param p_ptt
- * @param source_addr
- * @param grc_addr (dmae_data_offset)
- * @param size_in_dwords
- * @param p_params (default parameters will be used in case of NULL)
+ * Return: Int.
  */
 int
 qed_dmae_host2grc(struct qed_hwfn *p_hwfn,
@@ -224,29 +253,34 @@
 		  struct qed_dmae_params *p_params);
 
  /**
- * @brief qed_dmae_grc2host - Read data from dmae data offset
- * to source address using the given ptt
+ * qed_dmae_grc2host(): Read data from dmae data offset
+ *                      to source address using the given ptt.
+ *
+ * @p_ptt: P_ptt.
+ * @grc_addr: GRC address (dmae_data_offset).
+ * @dest_addr: Destination Address.
+ * @size_in_dwords: Size.
+ * @p_params: (default parameters will be used in case of NULL).
  *
- * @param p_ptt
- * @param grc_addr (dmae_data_offset)
- * @param dest_addr
- * @param size_in_dwords
- * @param p_params (default parameters will be used in case of NULL)
+ * Return: Int.
  */
 int qed_dmae_grc2host(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt,
 		      u32 grc_addr, dma_addr_t dest_addr, u32 size_in_dwords,
 		      struct qed_dmae_params *p_params);
 
 /**
- * @brief qed_dmae_host2host - copy data from to source address
- * to a destination adress (for SRIOV) using the given ptt
+ * qed_dmae_host2host(): Copy data from to source address
+ *                       to a destination adrress (for SRIOV) using the given
+ *                       ptt.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @source_addr: Source address.
+ * @dest_addr: Destination address.
+ * @size_in_dwords: size.
+ * @p_params: (default parameters will be used in case of NULL).
  *
- * @param p_hwfn
- * @param p_ptt
- * @param source_addr
- * @param dest_addr
- * @param size_in_dwords
- * @param p_params (default parameters will be used in case of NULL)
+ * Return: Int.
  */
 int qed_dmae_host2host(struct qed_hwfn *p_hwfn,
 		       struct qed_ptt *p_ptt,
@@ -259,51 +293,51 @@
 void qed_chain_free(struct qed_dev *cdev, struct qed_chain *chain);
 
 /**
- * @@brief qed_fw_l2_queue - Get absolute L2 queue ID
+ * qed_fw_l2_queue(): Get absolute L2 queue ID.
  *
- *  @param p_hwfn
- *  @param src_id - relative to p_hwfn
- *  @param dst_id - absolute per engine
+ * @p_hwfn: HW device data.
+ * @src_id: Relative to p_hwfn.
+ * @dst_id: Absolute per engine.
  *
- *  @return int
+ * Return: Int.
  */
 int qed_fw_l2_queue(struct qed_hwfn *p_hwfn,
 		    u16 src_id,
 		    u16 *dst_id);
 
 /**
- * @@brief qed_fw_vport - Get absolute vport ID
+ * qed_fw_vport(): Get absolute vport ID.
  *
- *  @param p_hwfn
- *  @param src_id - relative to p_hwfn
- *  @param dst_id - absolute per engine
+ * @p_hwfn: HW device data.
+ * @src_id: Relative to p_hwfn.
+ * @dst_id: Absolute per engine.
  *
- *  @return int
+ * Return: Int.
  */
 int qed_fw_vport(struct qed_hwfn *p_hwfn,
 		 u8 src_id,
 		 u8 *dst_id);
 
 /**
- * @@brief qed_fw_rss_eng - Get absolute RSS engine ID
+ * qed_fw_rss_eng(): Get absolute RSS engine ID.
  *
- *  @param p_hwfn
- *  @param src_id - relative to p_hwfn
- *  @param dst_id - absolute per engine
+ * @p_hwfn: HW device data.
+ * @src_id: Relative to p_hwfn.
+ * @dst_id: Absolute per engine.
  *
- *  @return int
+ * Return: Int.
  */
 int qed_fw_rss_eng(struct qed_hwfn *p_hwfn,
 		   u8 src_id,
 		   u8 *dst_id);
 
 /**
- * @brief qed_llh_get_num_ppfid - Return the allocated number of LLH filter
- *	banks that are allocated to the PF.
+ * qed_llh_get_num_ppfid(): Return the allocated number of LLH filter
+ *	                    banks that are allocated to the PF.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return u8 - Number of LLH filter banks
+ * Return: u8 Number of LLH filter banks.
  */
 u8 qed_llh_get_num_ppfid(struct qed_dev *cdev);
 
@@ -314,45 +348,50 @@
 };
 
 /**
- * @brief qed_llh_set_ppfid_affinity - Set the engine affinity for the given
- *	LLH filter bank.
+ * qed_llh_set_ppfid_affinity(): Set the engine affinity for the given
+ *	                         LLH filter bank.
  *
- * @param cdev
- * @param ppfid - relative within the allocated ppfids ('0' is the default one).
- * @param eng
+ * @cdev: Qed dev pointer.
+ * @ppfid: Relative within the allocated ppfids ('0' is the default one).
+ * @eng: Engine.
  *
- * @return int
+ * Return: Int.
  */
 int qed_llh_set_ppfid_affinity(struct qed_dev *cdev,
 			       u8 ppfid, enum qed_eng eng);
 
 /**
- * @brief qed_llh_set_roce_affinity - Set the RoCE engine affinity
+ * qed_llh_set_roce_affinity(): Set the RoCE engine affinity.
  *
- * @param cdev
- * @param eng
+ * @cdev: Qed dev pointer.
+ * @eng: Engine.
  *
- * @return int
+ * Return: Int.
  */
 int qed_llh_set_roce_affinity(struct qed_dev *cdev, enum qed_eng eng);
 
 /**
- * @brief qed_llh_add_mac_filter - Add a LLH MAC filter into the given filter
- *	bank.
+ * qed_llh_add_mac_filter(): Add a LLH MAC filter into the given filter
+ *	                     bank.
  *
- * @param cdev
- * @param ppfid - relative within the allocated ppfids ('0' is the default one).
- * @param mac_addr - MAC to add
+ * @cdev: Qed dev pointer.
+ * @ppfid: Relative within the allocated ppfids ('0' is the default one).
+ * @mac_addr: MAC to add.
+ *
+ * Return: Int.
  */
 int qed_llh_add_mac_filter(struct qed_dev *cdev,
-			   u8 ppfid, u8 mac_addr[ETH_ALEN]);
+			   u8 ppfid, const u8 mac_addr[ETH_ALEN]);
 
 /**
- * @brief qed_llh_remove_mac_filter - Remove a LLH MAC filter from the given
- *	filter bank.
+ * qed_llh_remove_mac_filter(): Remove a LLH MAC filter from the given
+ *	                        filter bank.
+ *
+ * @cdev: Qed dev pointer.
+ * @ppfid: Ppfid.
+ * @mac_addr: MAC to remove
  *
- * @param p_ptt
- * @param p_filter - MAC to remove
+ * Return: Void.
  */
 void qed_llh_remove_mac_filter(struct qed_dev *cdev,
 			       u8 ppfid, u8 mac_addr[ETH_ALEN]);
@@ -368,15 +407,16 @@
 };
 
 /**
- * @brief qed_llh_add_protocol_filter - Add a LLH protocol filter into the
- *	given filter bank.
+ * qed_llh_add_protocol_filter(): Add a LLH protocol filter into the
+ *	                          given filter bank.
+ *
+ * @cdev: Qed dev pointer.
+ * @ppfid: Relative within the allocated ppfids ('0' is the default one).
+ * @type: Type of filters and comparing.
+ * @source_port_or_eth_type: Source port or ethertype to add.
+ * @dest_port: Destination port to add.
  *
- * @param cdev
- * @param ppfid - relative within the allocated ppfids ('0' is the default one).
- * @param type - type of filters and comparing
- * @param source_port_or_eth_type - source port or ethertype to add
- * @param dest_port - destination port to add
- * @param type - type of filters and comparing
+ * Return: Int.
  */
 int
 qed_llh_add_protocol_filter(struct qed_dev *cdev,
@@ -385,14 +425,14 @@
 			    u16 source_port_or_eth_type, u16 dest_port);
 
 /**
- * @brief qed_llh_remove_protocol_filter - Remove a LLH protocol filter from
- *	the given filter bank.
+ * qed_llh_remove_protocol_filter(): Remove a LLH protocol filter from
+ *	                             the given filter bank.
  *
- * @param cdev
- * @param ppfid - relative within the allocated ppfids ('0' is the default one).
- * @param type - type of filters and comparing
- * @param source_port_or_eth_type - source port or ethertype to add
- * @param dest_port - destination port to add
+ * @cdev: Qed dev pointer.
+ * @ppfid: Relative within the allocated ppfids ('0' is the default one).
+ * @type: Type of filters and comparing.
+ * @source_port_or_eth_type: Source port or ethertype to add.
+ * @dest_port: Destination port to add.
  */
 void
 qed_llh_remove_protocol_filter(struct qed_dev *cdev,
@@ -401,31 +441,31 @@
 			       u16 source_port_or_eth_type, u16 dest_port);
 
 /**
- * *@brief Cleanup of previous driver remains prior to load
+ * qed_final_cleanup(): Cleanup of previous driver remains prior to load.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param id - For PF, engine-relative. For VF, PF-relative.
- * @param is_vf - true iff cleanup is made for a VF.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @id: For PF, engine-relative. For VF, PF-relative.
+ * @is_vf: True iff cleanup is made for a VF.
  *
- * @return int
+ * Return: Int.
  */
 int qed_final_cleanup(struct qed_hwfn *p_hwfn,
 		      struct qed_ptt *p_ptt, u16 id, bool is_vf);
 
 /**
- * @brief qed_get_queue_coalesce - Retrieve coalesce value for a given queue.
+ * qed_get_queue_coalesce(): Retrieve coalesce value for a given queue.
  *
- * @param p_hwfn
- * @param p_coal - store coalesce value read from the hardware.
- * @param p_handle
+ * @p_hwfn: HW device data.
+ * @coal: Store coalesce value read from the hardware.
+ * @handle: P_handle.
  *
- * @return int
+ * Return: Int.
  **/
 int qed_get_queue_coalesce(struct qed_hwfn *p_hwfn, u16 *coal, void *handle);
 
 /**
- * @brief qed_set_queue_coalesce - Configure coalesce parameters for Rx and
+ * qed_set_queue_coalesce(): Configure coalesce parameters for Rx and
  *    Tx queue. The fact that we can configure coalescing to up to 511, but on
  *    varying accuracy [the bigger the value the less accurate] up to a mistake
  *    of 3usec for the highest values.
@@ -433,37 +473,38 @@
  *    should be in same range [i.e., either 0-0x7f, 0x80-0xff or 0x100-0x1ff]
  *    otherwise configuration would break.
  *
+ * @rx_coal: Rx Coalesce value in micro seconds.
+ * @tx_coal: TX Coalesce value in micro seconds.
+ * @p_handle: P_handle.
  *
- * @param rx_coal - Rx Coalesce value in micro seconds.
- * @param tx_coal - TX Coalesce value in micro seconds.
- * @param p_handle
- *
- * @return int
+ * Return: Int.
  **/
 int
 qed_set_queue_coalesce(u16 rx_coal, u16 tx_coal, void *p_handle);
 
 /**
- * @brief qed_pglueb_set_pfid_enable - Enable or disable PCI BUS MASTER
+ * qed_pglueb_set_pfid_enable(): Enable or disable PCI BUS MASTER.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param b_enable - true/false
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @b_enable: True/False.
  *
- * @return int
+ * Return: Int.
  */
 int qed_pglueb_set_pfid_enable(struct qed_hwfn *p_hwfn,
 			       struct qed_ptt *p_ptt, bool b_enable);
 
 /**
- * @brief db_recovery_add - add doorbell information to the doorbell
- * recovery mechanism.
+ * qed_db_recovery_add(): add doorbell information to the doorbell
+ *                    recovery mechanism.
+ *
+ * @cdev: Qed dev pointer.
+ * @db_addr: Doorbell address.
+ * @db_data: Address of where db_data is stored.
+ * @db_width: Doorbell is 32b pr 64b.
+ * @db_space: Doorbell recovery addresses are user or kernel space.
  *
- * @param cdev
- * @param db_addr - doorbell address
- * @param db_data - address of where db_data is stored
- * @param db_width - doorbell is 32b pr 64b
- * @param db_space - doorbell recovery addresses are user or kernel space
+ * Return: Int.
  */
 int qed_db_recovery_add(struct qed_dev *cdev,
 			void __iomem *db_addr,
@@ -472,13 +513,15 @@
 			enum qed_db_rec_space db_space);
 
 /**
- * @brief db_recovery_del - remove doorbell information from the doorbell
+ * qed_db_recovery_del() - remove doorbell information from the doorbell
  * recovery mechanism. db_data serves as key (db_addr is not unique).
  *
- * @param cdev
- * @param db_addr - doorbell address
- * @param db_data - address where db_data is stored. Serves as key for the
+ * @cdev: Qed dev pointer.
+ * @db_addr: doorbell address.
+ * @db_data: address where db_data is stored. Serves as key for the
  *                  entry to delete.
+ *
+ * Return: Int.
  */
 int qed_db_recovery_del(struct qed_dev *cdev,
 			void __iomem *db_addr, void *db_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_fcoe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_fcoe.c
@@ -694,13 +694,14 @@
 }
 
 static int qed_fcoe_get_stats(struct qed_hwfn *p_hwfn,
-			      struct qed_fcoe_stats *p_stats)
+			      struct qed_fcoe_stats *p_stats,
+			      bool is_atomic)
 {
 	struct qed_ptt *p_ptt;
 
 	memset(p_stats, 0, sizeof(*p_stats));
 
-	p_ptt = qed_ptt_acquire(p_hwfn);
+	p_ptt = qed_ptt_acquire_context(p_hwfn, is_atomic);
 
 	if (!p_ptt) {
 		DP_ERR(p_hwfn, "Failed to acquire ptt\n");
@@ -974,19 +975,27 @@
 					QED_SPQ_MODE_EBLOCK, NULL);
 }
 
+static int qed_fcoe_stats_context(struct qed_dev *cdev,
+				  struct qed_fcoe_stats *stats,
+				  bool is_atomic)
+{
+	return qed_fcoe_get_stats(QED_AFFIN_HWFN(cdev), stats, is_atomic);
+}
+
 static int qed_fcoe_stats(struct qed_dev *cdev, struct qed_fcoe_stats *stats)
 {
-	return qed_fcoe_get_stats(QED_AFFIN_HWFN(cdev), stats);
+	return qed_fcoe_stats_context(cdev, stats, false);
 }
 
 void qed_get_protocol_stats_fcoe(struct qed_dev *cdev,
-				 struct qed_mcp_fcoe_stats *stats)
+				 struct qed_mcp_fcoe_stats *stats,
+				 bool is_atomic)
 {
 	struct qed_fcoe_stats proto_stats;
 
 	/* Retrieve FW statistics */
 	memset(&proto_stats, 0, sizeof(proto_stats));
-	if (qed_fcoe_stats(cdev, &proto_stats)) {
+	if (qed_fcoe_stats_context(cdev, &proto_stats, is_atomic)) {
 		DP_VERBOSE(cdev, QED_MSG_STORAGE,
 			   "Failed to collect FCoE statistics\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_fcoe.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_fcoe.h
@@ -28,8 +28,20 @@
 void qed_fcoe_setup(struct qed_hwfn *p_hwfn);
 
 void qed_fcoe_free(struct qed_hwfn *p_hwfn);
+/**
+ * qed_get_protocol_stats_fcoe(): Fills provided statistics
+ *				  struct with statistics.
+ *
+ * @cdev: Qed dev pointer.
+ * @stats: Points to struct that will be filled with statistics.
+ * @is_atomic: Hint from the caller - if the func can sleep or not.
+ *
+ * Context: The function should not sleep in case is_atomic == true.
+ * Return: Void.
+ */
 void qed_get_protocol_stats_fcoe(struct qed_dev *cdev,
-				 struct qed_mcp_fcoe_stats *stats);
+				 struct qed_mcp_fcoe_stats *stats,
+				 bool is_atomic);
 #else /* CONFIG_QED_FCOE */
 static inline int qed_fcoe_alloc(struct qed_hwfn *p_hwfn)
 {
@@ -40,7 +52,8 @@
 static inline void qed_fcoe_free(struct qed_hwfn *p_hwfn) {}
 
 static inline void qed_get_protocol_stats_fcoe(struct qed_dev *cdev,
-					       struct qed_mcp_fcoe_stats *stats)
+					       struct qed_mcp_fcoe_stats *stats,
+					       bool is_atomic)
 {
 }
 #endif /* CONFIG_QED_FCOE */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_hsi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_hsi.h
@@ -3012,96 +3012,102 @@
 /***************************** Public Functions *******************************/
 
 /**
- * @brief qed_dbg_set_bin_ptr - Sets a pointer to the binary data with debug
- *	arrays.
+ * qed_dbg_set_bin_ptr(): Sets a pointer to the binary data with debug
+ *                        arrays.
  *
- * @param p_hwfn -	    HW device data
- * @param bin_ptr - a pointer to the binary data with debug arrays.
+ * @p_hwfn: HW device data.
+ * @bin_ptr: A pointer to the binary data with debug arrays.
+ *
+ * Return: enum dbg status.
  */
 enum dbg_status qed_dbg_set_bin_ptr(struct qed_hwfn *p_hwfn,
 				    const u8 * const bin_ptr);
 
 /**
- * @brief qed_read_regs - Reads registers into a buffer (using GRC).
+ * qed_read_regs(): Reads registers into a buffer (using GRC).
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf: Destination buffer.
+ * @addr: Source GRC address in dwords.
+ * @len: Number of registers to read.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf - Destination buffer.
- * @param addr - Source GRC address in dwords.
- * @param len - Number of registers to read.
+ * Return: Void.
  */
 void qed_read_regs(struct qed_hwfn *p_hwfn,
 		   struct qed_ptt *p_ptt, u32 *buf, u32 addr, u32 len);
 
 /**
- * @brief qed_read_fw_info - Reads FW info from the chip.
+ * qed_read_fw_info(): Reads FW info from the chip.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @fw_info: (Out) a pointer to write the FW info into.
+ *
+ * Return: True if the FW info was read successfully from one of the Storms,
+ * or false if all Storms are in reset.
  *
  * The FW info contains FW-related information, such as the FW version,
  * FW image (main/L2B/kuku), FW timestamp, etc.
  * The FW info is read from the internal RAM of the first Storm that is not in
  * reset.
- *
- * @param p_hwfn -	    HW device data
- * @param p_ptt -	    Ptt window used for writing the registers.
- * @param fw_info -	Out: a pointer to write the FW info into.
- *
- * @return true if the FW info was read successfully from one of the Storms,
- * or false if all Storms are in reset.
  */
 bool qed_read_fw_info(struct qed_hwfn *p_hwfn,
 		      struct qed_ptt *p_ptt, struct fw_info *fw_info);
 /**
- * @brief qed_dbg_grc_config - Sets the value of a GRC parameter.
+ * qed_dbg_grc_config(): Sets the value of a GRC parameter.
  *
- * @param p_hwfn -	HW device data
- * @param grc_param -	GRC parameter
- * @param val -		Value to set.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- grc_param is invalid
- *	- val is outside the allowed boundaries
+ * @p_hwfn: HW device data.
+ * @grc_param: GRC parameter.
+ * @val: Value to set.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *         - Grc_param is invalid.
+ *         - Val is outside the allowed boundaries.
  */
 enum dbg_status qed_dbg_grc_config(struct qed_hwfn *p_hwfn,
 				   enum dbg_grc_params grc_param, u32 val);
 
 /**
- * @brief qed_dbg_grc_set_params_default - Reverts all GRC parameters to their
- *	default value.
+ * qed_dbg_grc_set_params_default(): Reverts all GRC parameters to their
+ *                                   default value.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn		- HW device data
+ * Return: Void.
  */
 void qed_dbg_grc_set_params_default(struct qed_hwfn *p_hwfn);
 /**
- * @brief qed_dbg_grc_get_dump_buf_size - Returns the required buffer size for
- *	GRC Dump.
+ * qed_dbg_grc_get_dump_buf_size(): Returns the required buffer size for
+ *                                  GRC Dump.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for the GRC Dump
- *	data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) required buffer size (in dwords) for the GRC Dump
+ *             data.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_grc_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 					      struct qed_ptt *p_ptt,
 					      u32 *buf_size);
 
 /**
- * @brief qed_dbg_grc_dump - Dumps GRC data into the specified buffer.
+ * qed_dbg_grc_dump(): Dumps GRC data into the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the collected GRC data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified dump buffer is too small
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the collected GRC data into.
+ * @buf_size_in_dwords:Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * Return: Error if one of the following holds:
+ *        - The version wasn't set.
+ *        - The specified dump buffer is too small.
+ *          Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_grc_dump(struct qed_hwfn *p_hwfn,
 				 struct qed_ptt *p_ptt,
@@ -3110,36 +3116,36 @@
 				 u32 *num_dumped_dwords);
 
 /**
- * @brief qed_dbg_idle_chk_get_dump_buf_size - Returns the required buffer size
- *	for idle check results.
+ * qed_dbg_idle_chk_get_dump_buf_size(): Returns the required buffer size
+ *                                       for idle check results.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for the idle check
- *	data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) required buffer size (in dwords) for the idle check
+ *             data.
+ *
+ * return: Error if one of the following holds:
+ *        - The version wasn't set.
+ *          Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_idle_chk_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 						   struct qed_ptt *p_ptt,
 						   u32 *buf_size);
 
 /**
- * @brief qed_dbg_idle_chk_dump - Performs idle check and writes the results
- *	into the specified buffer.
+ * qed_dbg_idle_chk_dump: Performs idle check and writes the results
+ *                        into the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the idle check data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified buffer is too small
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the idle check data into.
+ * @buf_size_in_dwords: Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *         - The specified buffer is too small.
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_idle_chk_dump(struct qed_hwfn *p_hwfn,
 				      struct qed_ptt *p_ptt,
@@ -3148,42 +3154,42 @@
 				      u32 *num_dumped_dwords);
 
 /**
- * @brief qed_dbg_mcp_trace_get_dump_buf_size - Returns the required buffer size
- *	for mcp trace results.
+ * qed_dbg_mcp_trace_get_dump_buf_size(): Returns the required buffer size
+ *                                        for mcp trace results.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for mcp trace data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the trace data in MCP scratchpad contain an invalid signature
- *	- the bundle ID in NVRAM is invalid
- *	- the trace meta data cannot be found (in NVRAM or image file)
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) Required buffer size (in dwords) for mcp trace data.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *         - The trace data in MCP scratchpad contain an invalid signature.
+ *         - The bundle ID in NVRAM is invalid.
+ *         - The trace meta data cannot be found (in NVRAM or image file).
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_mcp_trace_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 						    struct qed_ptt *p_ptt,
 						    u32 *buf_size);
 
 /**
- * @brief qed_dbg_mcp_trace_dump - Performs mcp trace and writes the results
- *	into the specified buffer.
+ * qed_dbg_mcp_trace_dump(): Performs mcp trace and writes the results
+ *                           into the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the mcp trace data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified buffer is too small
- *	- the trace data in MCP scratchpad contain an invalid signature
- *	- the bundle ID in NVRAM is invalid
- *	- the trace meta data cannot be found (in NVRAM or image file)
- *	- the trace meta data cannot be read (from NVRAM or image file)
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the mcp trace data into.
+ * @buf_size_in_dwords: Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * Return: Error if one of the following holds:
+ *        - The version wasn't set.
+ *        - The specified buffer is too small.
+ *        - The trace data in MCP scratchpad contain an invalid signature.
+ *        - The bundle ID in NVRAM is invalid.
+ *        - The trace meta data cannot be found (in NVRAM or image file).
+ *        - The trace meta data cannot be read (from NVRAM or image file).
+ *          Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_mcp_trace_dump(struct qed_hwfn *p_hwfn,
 				       struct qed_ptt *p_ptt,
@@ -3192,36 +3198,36 @@
 				       u32 *num_dumped_dwords);
 
 /**
- * @brief qed_dbg_reg_fifo_get_dump_buf_size - Returns the required buffer size
- *	for grc trace fifo results.
+ * qed_dbg_reg_fifo_get_dump_buf_size(): Returns the required buffer size
+ *                                       for grc trace fifo results.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for reg fifo data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) Required buffer size (in dwords) for reg fifo data.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_reg_fifo_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 						   struct qed_ptt *p_ptt,
 						   u32 *buf_size);
 
 /**
- * @brief qed_dbg_reg_fifo_dump - Reads the reg fifo and writes the results into
- *	the specified buffer.
+ * qed_dbg_reg_fifo_dump(): Reads the reg fifo and writes the results into
+ *                          the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the reg fifo data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified buffer is too small
- *	- DMAE transaction failed
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the reg fifo data into.
+ * @buf_size_in_dwords: Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * Return: Error if one of the following holds:
+ *        - The version wasn't set.
+ *        - The specified buffer is too small.
+ *        - DMAE transaction failed.
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_reg_fifo_dump(struct qed_hwfn *p_hwfn,
 				      struct qed_ptt *p_ptt,
@@ -3230,37 +3236,37 @@
 				      u32 *num_dumped_dwords);
 
 /**
- * @brief qed_dbg_igu_fifo_get_dump_buf_size - Returns the required buffer size
- *	for the IGU fifo results.
+ * qed_dbg_igu_fifo_get_dump_buf_size(): Returns the required buffer size
+ *                                       for the IGU fifo results.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for the IGU fifo
- *	data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) Required buffer size (in dwords) for the IGU fifo
+ *            data.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_igu_fifo_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 						   struct qed_ptt *p_ptt,
 						   u32 *buf_size);
 
 /**
- * @brief qed_dbg_igu_fifo_dump - Reads the IGU fifo and writes the results into
- *	the specified buffer.
+ * qed_dbg_igu_fifo_dump(): Reads the IGU fifo and writes the results into
+ *                          the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the IGU fifo data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified buffer is too small
- *	- DMAE transaction failed
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the IGU fifo data into.
+ * @buf_size_in_dwords: Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set
+ *         - The specified buffer is too small
+ *         - DMAE transaction failed
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_igu_fifo_dump(struct qed_hwfn *p_hwfn,
 				      struct qed_ptt *p_ptt,
@@ -3269,37 +3275,37 @@
 				      u32 *num_dumped_dwords);
 
 /**
- * @brief qed_dbg_protection_override_get_dump_buf_size - Returns the required
- *	buffer size for protection override window results.
+ * qed_dbg_protection_override_get_dump_buf_size(): Returns the required
+ *        buffer size for protection override window results.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for protection
- *	override data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) Required buffer size (in dwords) for protection
+ *             override data.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set
+ *           Otherwise, returns ok.
  */
 enum dbg_status
 qed_dbg_protection_override_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 					      struct qed_ptt *p_ptt,
 					      u32 *buf_size);
 /**
- * @brief qed_dbg_protection_override_dump - Reads protection override window
- *	entries and writes the results into the specified buffer.
+ * qed_dbg_protection_override_dump(): Reads protection override window
+ *       entries and writes the results into the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the protection override data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified buffer is too small
- *	- DMAE transaction failed
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the protection override data into.
+ * @buf_size_in_dwords: Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * @return: Error if one of the following holds:
+ *          - The version wasn't set.
+ *          - The specified buffer is too small.
+ *          - DMAE transaction failed.
+ *             Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_protection_override_dump(struct qed_hwfn *p_hwfn,
 						 struct qed_ptt *p_ptt,
@@ -3307,34 +3313,34 @@
 						 u32 buf_size_in_dwords,
 						 u32 *num_dumped_dwords);
 /**
- * @brief qed_dbg_fw_asserts_get_dump_buf_size - Returns the required buffer
- *	size for FW Asserts results.
+ * qed_dbg_fw_asserts_get_dump_buf_size(): Returns the required buffer
+ *                                         size for FW Asserts results.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param buf_size - OUT: required buffer size (in dwords) for FW Asserts data.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @buf_size: (OUT) Required buffer size (in dwords) for FW Asserts data.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_fw_asserts_get_dump_buf_size(struct qed_hwfn *p_hwfn,
 						     struct qed_ptt *p_ptt,
 						     u32 *buf_size);
 /**
- * @brief qed_dbg_fw_asserts_dump - Reads the FW Asserts and writes the results
- *	into the specified buffer.
+ * qed_dbg_fw_asserts_dump(): Reads the FW Asserts and writes the results
+ *                            into the specified buffer.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - Ptt window used for writing the registers.
- * @param dump_buf - Pointer to write the FW Asserts data into.
- * @param buf_size_in_dwords - Size of the specified buffer in dwords.
- * @param num_dumped_dwords - OUT: number of dumped dwords.
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- *	- the specified buffer is too small
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dump_buf: Pointer to write the FW Asserts data into.
+ * @buf_size_in_dwords: Size of the specified buffer in dwords.
+ * @num_dumped_dwords: (OUT) number of dumped dwords.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *         - The specified buffer is too small.
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_fw_asserts_dump(struct qed_hwfn *p_hwfn,
 					struct qed_ptt *p_ptt,
@@ -3343,19 +3349,19 @@
 					u32 *num_dumped_dwords);
 
 /**
- * @brief qed_dbg_read_attn - Reads the attention registers of the specified
+ * qed_dbg_read_attn(): Reads the attention registers of the specified
  * block and type, and writes the results into the specified buffer.
  *
- * @param p_hwfn -	 HW device data
- * @param p_ptt -	 Ptt window used for writing the registers.
- * @param block -	 Block ID.
- * @param attn_type -	 Attention type.
- * @param clear_status - Indicates if the attention status should be cleared.
- * @param results -	 OUT: Pointer to write the read results into
- *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @block: Block ID.
+ * @attn_type: Attention type.
+ * @clear_status: Indicates if the attention status should be cleared.
+ * @results:  (OUT) Pointer to write the read results into.
+ *
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set
+ *          Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_read_attn(struct qed_hwfn *p_hwfn,
 				  struct qed_ptt *p_ptt,
@@ -3365,15 +3371,15 @@
 				  struct dbg_attn_block_result *results);
 
 /**
- * @brief qed_dbg_print_attn - Prints attention registers values in the
- *	specified results struct.
+ * qed_dbg_print_attn(): Prints attention registers values in the
+ *                       specified results struct.
  *
- * @param p_hwfn
- * @param results - Pointer to the attention read results
+ * @p_hwfn: HW device data.
+ * @results: Pointer to the attention read results
  *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * Return: Error if one of the following holds:
+ *        - The version wasn't set
+ *          Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_print_attn(struct qed_hwfn *p_hwfn,
 				   struct dbg_attn_block_result *results);
@@ -3420,60 +3426,64 @@
 /***************************** Public Functions *******************************/
 
 /**
- * @brief qed_dbg_user_set_bin_ptr - Sets a pointer to the binary data with
- *	debug arrays.
+ * qed_dbg_user_set_bin_ptr(): Sets a pointer to the binary data with
+ *                             debug arrays.
  *
- * @param p_hwfn - HW device data
- * @param bin_ptr - a pointer to the binary data with debug arrays.
+ * @p_hwfn: HW device data.
+ * @bin_ptr: a pointer to the binary data with debug arrays.
+ *
+ * Return: dbg_status.
  */
 enum dbg_status qed_dbg_user_set_bin_ptr(struct qed_hwfn *p_hwfn,
 					 const u8 * const bin_ptr);
 
 /**
- * @brief qed_dbg_alloc_user_data - Allocates user debug data.
+ * qed_dbg_alloc_user_data(): Allocates user debug data.
+ *
+ * @p_hwfn: HW device data.
+ * @user_data_ptr: (OUT) a pointer to the allocated memory.
  *
- * @param p_hwfn -		 HW device data
- * @param user_data_ptr - OUT: a pointer to the allocated memory.
+ * Return: dbg_status.
  */
 enum dbg_status qed_dbg_alloc_user_data(struct qed_hwfn *p_hwfn,
 					void **user_data_ptr);
 
 /**
- * @brief qed_dbg_get_status_str - Returns a string for the specified status.
+ * qed_dbg_get_status_str(): Returns a string for the specified status.
  *
- * @param status - a debug status code.
+ * @status: A debug status code.
  *
- * @return a string for the specified status
+ * Return: A string for the specified status.
  */
 const char *qed_dbg_get_status_str(enum dbg_status status);
 
 /**
- * @brief qed_get_idle_chk_results_buf_size - Returns the required buffer size
- *	for idle check results (in bytes).
+ * qed_get_idle_chk_results_buf_size(): Returns the required buffer size
+ *                                      for idle check results (in bytes).
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - idle check dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf_size - OUT: required buffer size (in bytes) for the parsed
- *	results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: idle check dump buffer.
+ * @num_dumped_dwords: number of dwords that were dumped.
+ * @results_buf_size: (OUT) required buffer size (in bytes) for the parsed
+ *                    results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_get_idle_chk_results_buf_size(struct qed_hwfn *p_hwfn,
 						  u32 *dump_buf,
 						  u32  num_dumped_dwords,
 						  u32 *results_buf_size);
 /**
- * @brief qed_print_idle_chk_results - Prints idle check results
+ * qed_print_idle_chk_results(): Prints idle check results
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - idle check dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf - buffer for printing the idle check results.
- * @param num_errors - OUT: number of errors found in idle check.
- * @param num_warnings - OUT: number of warnings found in idle check.
+ * @p_hwfn: HW device data.
+ * @dump_buf: idle check dump buffer.
+ * @num_dumped_dwords: number of dwords that were dumped.
+ * @results_buf: buffer for printing the idle check results.
+ * @num_errors: (OUT) number of errors found in idle check.
+ * @num_warnings: (OUT) number of warnings found in idle check.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_idle_chk_results(struct qed_hwfn *p_hwfn,
 					   u32 *dump_buf,
@@ -3483,28 +3493,30 @@
 					   u32 *num_warnings);
 
 /**
- * @brief qed_dbg_mcp_trace_set_meta_data - Sets the MCP Trace meta data.
+ * qed_dbg_mcp_trace_set_meta_data(): Sets the MCP Trace meta data.
+ *
+ * @p_hwfn: HW device data.
+ * @meta_buf: Meta buffer.
+ *
+ * Return: Void.
  *
  * Needed in case the MCP Trace dump doesn't contain the meta data (e.g. due to
  * no NVRAM access).
- *
- * @param data - pointer to MCP Trace meta data
- * @param size - size of MCP Trace meta data in dwords
  */
 void qed_dbg_mcp_trace_set_meta_data(struct qed_hwfn *p_hwfn,
 				     const u32 *meta_buf);
 
 /**
- * @brief qed_get_mcp_trace_results_buf_size - Returns the required buffer size
- *	for MCP Trace results (in bytes).
+ * qed_get_mcp_trace_results_buf_size(): Returns the required buffer size
+ *                                       for MCP Trace results (in bytes).
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - MCP Trace dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf_size - OUT: required buffer size (in bytes) for the parsed
- *	results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: MCP Trace dump buffer.
+ * @num_dumped_dwords: number of dwords that were dumped.
+ * @results_buf_size: (OUT) required buffer size (in bytes) for the parsed
+ *                    results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Rrror if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_get_mcp_trace_results_buf_size(struct qed_hwfn *p_hwfn,
 						   u32 *dump_buf,
@@ -3512,14 +3524,14 @@
 						   u32 *results_buf_size);
 
 /**
- * @brief qed_print_mcp_trace_results - Prints MCP Trace results
+ * qed_print_mcp_trace_results(): Prints MCP Trace results
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - mcp trace dump buffer, starting from the header.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf - buffer for printing the mcp trace results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: MCP trace dump buffer, starting from the header.
+ * @num_dumped_dwords: Member of dwords that were dumped.
+ * @results_buf: Buffer for printing the mcp trace results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_mcp_trace_results(struct qed_hwfn *p_hwfn,
 					    u32 *dump_buf,
@@ -3527,30 +3539,30 @@
 					    char *results_buf);
 
 /**
- * @brief qed_print_mcp_trace_results_cont - Prints MCP Trace results, and
+ * qed_print_mcp_trace_results_cont(): Prints MCP Trace results, and
  * keeps the MCP trace meta data allocated, to support continuous MCP Trace
  * parsing. After the continuous parsing ends, mcp_trace_free_meta_data should
  * be called to free the meta data.
  *
- * @param p_hwfn -	      HW device data
- * @param dump_buf -	      mcp trace dump buffer, starting from the header.
- * @param results_buf -	      buffer for printing the mcp trace results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: MVP trace dump buffer, starting from the header.
+ * @results_buf: Buffer for printing the mcp trace results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_mcp_trace_results_cont(struct qed_hwfn *p_hwfn,
 						 u32 *dump_buf,
 						 char *results_buf);
 
 /**
- * @brief print_mcp_trace_line - Prints MCP Trace results for a single line
+ * qed_print_mcp_trace_line(): Prints MCP Trace results for a single line
  *
- * @param p_hwfn -	      HW device data
- * @param dump_buf -	      mcp trace dump buffer, starting from the header.
- * @param num_dumped_bytes -  number of bytes that were dumped.
- * @param results_buf -	      buffer for printing the mcp trace results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: MCP trace dump buffer, starting from the header.
+ * @num_dumped_bytes: Number of bytes that were dumped.
+ * @results_buf: Buffer for printing the mcp trace results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_mcp_trace_line(struct qed_hwfn *p_hwfn,
 					 u8 *dump_buf,
@@ -3558,24 +3570,26 @@
 					 char *results_buf);
 
 /**
- * @brief mcp_trace_free_meta_data - Frees the MCP Trace meta data.
+ * qed_mcp_trace_free_meta_data(): Frees the MCP Trace meta data.
  * Should be called after continuous MCP Trace parsing.
  *
- * @param p_hwfn - HW device data
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_mcp_trace_free_meta_data(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_get_reg_fifo_results_buf_size - Returns the required buffer size
- *	for reg_fifo results (in bytes).
+ * qed_get_reg_fifo_results_buf_size(): Returns the required buffer size
+ *                                      for reg_fifo results (in bytes).
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - reg fifo dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf_size - OUT: required buffer size (in bytes) for the parsed
- *	results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: Reg fifo dump buffer.
+ * @num_dumped_dwords: Number of dwords that were dumped.
+ * @results_buf_size: (OUT) required buffer size (in bytes) for the parsed
+ *                     results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_get_reg_fifo_results_buf_size(struct qed_hwfn *p_hwfn,
 						  u32 *dump_buf,
@@ -3583,14 +3597,14 @@
 						  u32 *results_buf_size);
 
 /**
- * @brief qed_print_reg_fifo_results - Prints reg fifo results
+ * qed_print_reg_fifo_results(): Prints reg fifo results.
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - reg fifo dump buffer, starting from the header.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf - buffer for printing the reg fifo results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: Reg fifo dump buffer, starting from the header.
+ * @num_dumped_dwords: Number of dwords that were dumped.
+ * @results_buf: Buffer for printing the reg fifo results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_reg_fifo_results(struct qed_hwfn *p_hwfn,
 					   u32 *dump_buf,
@@ -3598,16 +3612,16 @@
 					   char *results_buf);
 
 /**
- * @brief qed_get_igu_fifo_results_buf_size - Returns the required buffer size
- *	for igu_fifo results (in bytes).
+ * qed_get_igu_fifo_results_buf_size(): Returns the required buffer size
+ *                                      for igu_fifo results (in bytes).
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - IGU fifo dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf_size - OUT: required buffer size (in bytes) for the parsed
- *	results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: IGU fifo dump buffer.
+ * @num_dumped_dwords: number of dwords that were dumped.
+ * @results_buf_size: (OUT) required buffer size (in bytes) for the parsed
+ *                    results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_get_igu_fifo_results_buf_size(struct qed_hwfn *p_hwfn,
 						  u32 *dump_buf,
@@ -3615,14 +3629,14 @@
 						  u32 *results_buf_size);
 
 /**
- * @brief qed_print_igu_fifo_results - Prints IGU fifo results
+ * qed_print_igu_fifo_results(): Prints IGU fifo results
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - IGU fifo dump buffer, starting from the header.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf - buffer for printing the IGU fifo results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: IGU fifo dump buffer, starting from the header.
+ * @num_dumped_dwords: Number of dwords that were dumped.
+ * @results_buf: Buffer for printing the IGU fifo results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_igu_fifo_results(struct qed_hwfn *p_hwfn,
 					   u32 *dump_buf,
@@ -3630,16 +3644,16 @@
 					   char *results_buf);
 
 /**
- * @brief qed_get_protection_override_results_buf_size - Returns the required
- *	buffer size for protection override results (in bytes).
+ * qed_get_protection_override_results_buf_size(): Returns the required
+ *         buffer size for protection override results (in bytes).
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - protection override dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf_size - OUT: required buffer size (in bytes) for the parsed
- *	results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: Protection override dump buffer.
+ * @num_dumped_dwords: Number of dwords that were dumped.
+ * @results_buf_size: (OUT) required buffer size (in bytes) for the parsed
+ *                    results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status
 qed_get_protection_override_results_buf_size(struct qed_hwfn *p_hwfn,
@@ -3648,15 +3662,15 @@
 					     u32 *results_buf_size);
 
 /**
- * @brief qed_print_protection_override_results - Prints protection override
- *	results.
+ * qed_print_protection_override_results(): Prints protection override
+ *                                          results.
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - protection override dump buffer, starting from the header.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf - buffer for printing the reg fifo results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: Protection override dump buffer, starting from the header.
+ * @num_dumped_dwords: Number of dwords that were dumped.
+ * @results_buf: Buffer for printing the reg fifo results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_protection_override_results(struct qed_hwfn *p_hwfn,
 						      u32 *dump_buf,
@@ -3664,16 +3678,16 @@
 						      char *results_buf);
 
 /**
- * @brief qed_get_fw_asserts_results_buf_size - Returns the required buffer size
- *	for FW Asserts results (in bytes).
+ * qed_get_fw_asserts_results_buf_size(): Returns the required buffer size
+ *                                        for FW Asserts results (in bytes).
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - FW Asserts dump buffer.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf_size - OUT: required buffer size (in bytes) for the parsed
- *	results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: FW Asserts dump buffer.
+ * @num_dumped_dwords: number of dwords that were dumped.
+ * @results_buf_size: (OUT) required buffer size (in bytes) for the parsed
+ *                    results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_get_fw_asserts_results_buf_size(struct qed_hwfn *p_hwfn,
 						    u32 *dump_buf,
@@ -3681,14 +3695,14 @@
 						    u32 *results_buf_size);
 
 /**
- * @brief qed_print_fw_asserts_results - Prints FW Asserts results
+ * qed_print_fw_asserts_results(): Prints FW Asserts results.
  *
- * @param p_hwfn - HW device data
- * @param dump_buf - FW Asserts dump buffer, starting from the header.
- * @param num_dumped_dwords - number of dwords that were dumped.
- * @param results_buf - buffer for printing the FW Asserts results.
+ * @p_hwfn: HW device data.
+ * @dump_buf: FW Asserts dump buffer, starting from the header.
+ * @num_dumped_dwords: number of dwords that were dumped.
+ * @results_buf: buffer for printing the FW Asserts results.
  *
- * @return error if the parsing fails, ok otherwise.
+ * Return: Error if the parsing fails, ok otherwise.
  */
 enum dbg_status qed_print_fw_asserts_results(struct qed_hwfn *p_hwfn,
 					     u32 *dump_buf,
@@ -3696,15 +3710,15 @@
 					     char *results_buf);
 
 /**
- * @brief qed_dbg_parse_attn - Parses and prints attention registers values in
- * the specified results struct.
+ * qed_dbg_parse_attn(): Parses and prints attention registers values in
+ *                      the specified results struct.
  *
- * @param p_hwfn -  HW device data
- * @param results - Pointer to the attention read results
+ * @p_hwfn: HW device data.
+ * @results: Pointer to the attention read results
  *
- * @return error if one of the following holds:
- *	- the version wasn't set
- * Otherwise, returns ok.
+ * Return: Error if one of the following holds:
+ *         - The version wasn't set.
+ *           Otherwise, returns ok.
  */
 enum dbg_status qed_dbg_parse_attn(struct qed_hwfn *p_hwfn,
 				   struct dbg_attn_block_result *results);
@@ -3746,18 +3760,18 @@
 #define GTT_BAR0_MAP_REG_PSDM_RAM	0x01a000UL
 
 /**
- * @brief qed_qm_pf_mem_size - prepare QM ILT sizes
+ * qed_qm_pf_mem_size(): Prepare QM ILT sizes.
  *
- * Returns the required host memory size in 4KB units.
- * Must be called before all QM init HSI functions.
+ * @num_pf_cids: Number of connections used by this PF.
+ * @num_vf_cids: Number of connections used by VFs of this PF.
+ * @num_tids: Number of tasks used by this PF.
+ * @num_pf_pqs: Number of PQs used by this PF.
+ * @num_vf_pqs: Number of PQs used by VFs of this PF.
  *
- * @param num_pf_cids - number of connections used by this PF
- * @param num_vf_cids - number of connections used by VFs of this PF
- * @param num_tids - number of tasks used by this PF
- * @param num_pf_pqs - number of PQs used by this PF
- * @param num_vf_pqs - number of PQs used by VFs of this PF
+ * Return: The required host memory size in 4KB units.
  *
- * @return The required host memory size in 4KB units.
+ * Returns the required host memory size in 4KB units.
+ * Must be called before all QM init HSI functions.
  */
 u32 qed_qm_pf_mem_size(u32 num_pf_cids,
 		       u32 num_vf_cids,
@@ -3800,74 +3814,74 @@
 	struct qed_qm_pf_rt_init_params *p_params);
 
 /**
- * @brief qed_init_pf_wfq - Initializes the WFQ weight of the specified PF
+ * qed_init_pf_wfq(): Initializes the WFQ weight of the specified PF.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers
- * @param pf_id - PF ID
- * @param pf_wfq - WFQ weight. Must be non-zero.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers
+ * @pf_id: PF ID
+ * @pf_wfq: WFQ weight. Must be non-zero.
  *
- * @return 0 on success, -1 on error.
+ * Return: 0 on success, -1 on error.
  */
 int qed_init_pf_wfq(struct qed_hwfn *p_hwfn,
 		    struct qed_ptt *p_ptt, u8 pf_id, u16 pf_wfq);
 
 /**
- * @brief qed_init_pf_rl - Initializes the rate limit of the specified PF
+ * qed_init_pf_rl(): Initializes the rate limit of the specified PF
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers
- * @param pf_id - PF ID
- * @param pf_rl - rate limit in Mb/sec units
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @pf_id: PF ID.
+ * @pf_rl: rate limit in Mb/sec units
  *
- * @return 0 on success, -1 on error.
+ * Return: 0 on success, -1 on error.
  */
 int qed_init_pf_rl(struct qed_hwfn *p_hwfn,
 		   struct qed_ptt *p_ptt, u8 pf_id, u32 pf_rl);
 
 /**
- * @brief qed_init_vport_wfq Initializes the WFQ weight of the specified VPORT
+ * qed_init_vport_wfq(): Initializes the WFQ weight of the specified VPORT
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers
- * @param first_tx_pq_id- An array containing the first Tx PQ ID associated
- *	  with the VPORT for each TC. This array is filled by
- *	  qed_qm_pf_rt_init
- * @param vport_wfq - WFQ weight. Must be non-zero.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers
+ * @first_tx_pq_id: An array containing the first Tx PQ ID associated
+ *                  with the VPORT for each TC. This array is filled by
+ *                  qed_qm_pf_rt_init
+ * @wfq: WFQ weight. Must be non-zero.
  *
- * @return 0 on success, -1 on error.
+ * Return: 0 on success, -1 on error.
  */
 int qed_init_vport_wfq(struct qed_hwfn *p_hwfn,
 		       struct qed_ptt *p_ptt,
 		       u16 first_tx_pq_id[NUM_OF_TCS], u16 wfq);
 
 /**
- * @brief qed_init_global_rl - Initializes the rate limit of the specified
- * rate limiter
+ * qed_init_global_rl():  Initializes the rate limit of the specified
+ * rate limiter.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers
- * @param rl_id - RL ID
- * @param rate_limit - rate limit in Mb/sec units
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @rl_id: RL ID.
+ * @rate_limit: Rate limit in Mb/sec units
  *
- * @return 0 on success, -1 on error.
+ * Return: 0 on success, -1 on error.
  */
 int qed_init_global_rl(struct qed_hwfn *p_hwfn,
 		       struct qed_ptt *p_ptt,
 		       u16 rl_id, u32 rate_limit);
 
 /**
- * @brief qed_send_qm_stop_cmd  Sends a stop command to the QM
+ * qed_send_qm_stop_cmd(): Sends a stop command to the QM.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param is_release_cmd - true for release, false for stop.
- * @param is_tx_pq - true for Tx PQs, false for Other PQs.
- * @param start_pq - first PQ ID to stop
- * @param num_pqs - Number of PQs to stop, starting from start_pq.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @is_release_cmd: true for release, false for stop.
+ * @is_tx_pq: true for Tx PQs, false for Other PQs.
+ * @start_pq: first PQ ID to stop
+ * @num_pqs: Number of PQs to stop, starting from start_pq.
  *
- * @return bool, true if successful, false if timeout occurred while waiting for
- *	QM command done.
+ * Return: Bool, true if successful, false if timeout occurred while waiting
+ *         for QM command done.
  */
 bool qed_send_qm_stop_cmd(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt,
@@ -3875,53 +3889,64 @@
 			  bool is_tx_pq, u16 start_pq, u16 num_pqs);
 
 /**
- * @brief qed_set_vxlan_dest_port - initializes vxlan tunnel destination udp port
+ * qed_set_vxlan_dest_port(): Initializes vxlan tunnel destination udp port.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers.
- * @param dest_port - vxlan destination udp port.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dest_port: vxlan destination udp port.
+ *
+ * Return: Void.
  */
 void qed_set_vxlan_dest_port(struct qed_hwfn *p_hwfn,
 			     struct qed_ptt *p_ptt, u16 dest_port);
 
 /**
- * @brief qed_set_vxlan_enable - enable or disable VXLAN tunnel in HW
+ * qed_set_vxlan_enable(): Enable or disable VXLAN tunnel in HW.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @vxlan_enable: vxlan enable flag.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers.
- * @param vxlan_enable - vxlan enable flag.
+ * Return: Void.
  */
 void qed_set_vxlan_enable(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt, bool vxlan_enable);
 
 /**
- * @brief qed_set_gre_enable - enable or disable GRE tunnel in HW
+ * qed_set_gre_enable(): Enable or disable GRE tunnel in HW.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers.
- * @param eth_gre_enable - eth GRE enable enable flag.
- * @param ip_gre_enable - IP GRE enable enable flag.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @eth_gre_enable: Eth GRE enable flag.
+ * @ip_gre_enable: IP GRE enable flag.
+ *
+ * Return: Void.
  */
 void qed_set_gre_enable(struct qed_hwfn *p_hwfn,
 			struct qed_ptt *p_ptt,
 			bool eth_gre_enable, bool ip_gre_enable);
 
 /**
- * @brief qed_set_geneve_dest_port - initializes geneve tunnel destination udp port
+ * qed_set_geneve_dest_port(): Initializes geneve tunnel destination udp port
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @dest_port: Geneve destination udp port.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers.
- * @param dest_port - geneve destination udp port.
+ * Retur: Void.
  */
 void qed_set_geneve_dest_port(struct qed_hwfn *p_hwfn,
 			      struct qed_ptt *p_ptt, u16 dest_port);
 
 /**
- * @brief qed_set_gre_enable - enable or disable GRE tunnel in HW
+ * qed_set_geneve_enable(): Enable or disable GRE tunnel in HW.
  *
- * @param p_ptt - ptt window used for writing the registers.
- * @param eth_geneve_enable - eth GENEVE enable enable flag.
- * @param ip_geneve_enable - IP GENEVE enable enable flag.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @eth_geneve_enable: Eth GENEVE enable flag.
+ * @ip_geneve_enable: IP GENEVE enable flag.
+ *
+ * Return: Void.
  */
 void qed_set_geneve_enable(struct qed_hwfn *p_hwfn,
 			   struct qed_ptt *p_ptt,
@@ -3931,25 +3956,29 @@
 				struct qed_ptt *p_ptt, bool enable);
 
 /**
- * @brief qed_gft_disable - Disable GFT
+ * qed_gft_disable(): Disable GFT.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @pf_id: PF on which to disable GFT.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers.
- * @param pf_id - pf on which to disable GFT.
+ * Return: Void.
  */
 void qed_gft_disable(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt, u16 pf_id);
 
 /**
- * @brief qed_gft_config - Enable and configure HW for GFT
+ * qed_gft_config(): Enable and configure HW for GFT.
  *
- * @param p_hwfn - HW device data
- * @param p_ptt - ptt window used for writing the registers.
- * @param pf_id - pf on which to enable GFT.
- * @param tcp - set profile tcp packets.
- * @param udp - set profile udp  packet.
- * @param ipv4 - set profile ipv4 packet.
- * @param ipv6 - set profile ipv6 packet.
- * @param profile_type - define packet same fields. Use enum gft_profile_type.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @pf_id: PF on which to enable GFT.
+ * @tcp: Set profile tcp packets.
+ * @udp: Set profile udp  packet.
+ * @ipv4: Set profile ipv4 packet.
+ * @ipv6: Set profile ipv6 packet.
+ * @profile_type: Define packet same fields. Use enum gft_profile_type.
+ *
+ * Return: Void.
  */
 void qed_gft_config(struct qed_hwfn *p_hwfn,
 		    struct qed_ptt *p_ptt,
@@ -3959,107 +3988,120 @@
 		    bool ipv4, bool ipv6, enum gft_profile_type profile_type);
 
 /**
- * @brief qed_enable_context_validation - Enable and configure context
- *	validation.
+ * qed_enable_context_validation(): Enable and configure context
+ *                                  validation.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
  *
- * @param p_hwfn
- * @param p_ptt - ptt window used for writing the registers.
+ * Return: Void.
  */
 void qed_enable_context_validation(struct qed_hwfn *p_hwfn,
 				   struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_calc_session_ctx_validation - Calcualte validation byte for
- *	session context.
+ * qed_calc_session_ctx_validation(): Calcualte validation byte for
+ *                                    session context.
  *
- * @param p_ctx_mem - pointer to context memory.
- * @param ctx_size - context size.
- * @param ctx_type - context type.
- * @param cid - context cid.
+ * @p_ctx_mem: Pointer to context memory.
+ * @ctx_size: Context size.
+ * @ctx_type: Context type.
+ * @cid: Context cid.
+ *
+ * Return: Void.
  */
 void qed_calc_session_ctx_validation(void *p_ctx_mem,
 				     u16 ctx_size, u8 ctx_type, u32 cid);
 
 /**
- * @brief qed_calc_task_ctx_validation - Calcualte validation byte for task
- *	context.
+ * qed_calc_task_ctx_validation(): Calcualte validation byte for task
+ *                                 context.
+ *
+ * @p_ctx_mem: Pointer to context memory.
+ * @ctx_size: Context size.
+ * @ctx_type: Context type.
+ * @tid: Context tid.
  *
- * @param p_ctx_mem - pointer to context memory.
- * @param ctx_size - context size.
- * @param ctx_type - context type.
- * @param tid - context tid.
+ * Return: Void.
  */
 void qed_calc_task_ctx_validation(void *p_ctx_mem,
 				  u16 ctx_size, u8 ctx_type, u32 tid);
 
 /**
- * @brief qed_memset_session_ctx - Memset session context to 0 while
- *	preserving validation bytes.
+ * qed_memset_session_ctx(): Memset session context to 0 while
+ *                            preserving validation bytes.
  *
- * @param p_hwfn -
- * @param p_ctx_mem - pointer to context memory.
- * @param ctx_size - size to initialzie.
- * @param ctx_type - context type.
+ * @p_ctx_mem: Pointer to context memory.
+ * @ctx_size: Size to initialzie.
+ * @ctx_type: Context type.
+ *
+ * Return: Void.
  */
 void qed_memset_session_ctx(void *p_ctx_mem, u32 ctx_size, u8 ctx_type);
 
 /**
- * @brief qed_memset_task_ctx - Memset task context to 0 while preserving
- *	validation bytes.
+ * qed_memset_task_ctx(): Memset task context to 0 while preserving
+ *                        validation bytes.
+ *
+ * @p_ctx_mem: Pointer to context memory.
+ * @ctx_size: size to initialzie.
+ * @ctx_type: context type.
  *
- * @param p_ctx_mem - pointer to context memory.
- * @param ctx_size - size to initialzie.
- * @param ctx_type - context type.
+ * Return: Void.
  */
 void qed_memset_task_ctx(void *p_ctx_mem, u32 ctx_size, u8 ctx_type);
 
 #define NUM_STORMS 6
 
 /**
- * @brief qed_set_rdma_error_level - Sets the RDMA assert level.
- *                                   If the severity of the error will be
- *                                   above the level, the FW will assert.
- * @param p_hwfn - HW device data
- * @param p_ptt - ptt window used for writing the registers
- * @param assert_level - An array of assert levels for each storm.
+ * qed_set_rdma_error_level(): Sets the RDMA assert level.
+ *                             If the severity of the error will be
+ *                             above the level, the FW will assert.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @assert_level: An array of assert levels for each storm.
  *
+ * Return: Void.
  */
 void qed_set_rdma_error_level(struct qed_hwfn *p_hwfn,
 			      struct qed_ptt *p_ptt,
 			      u8 assert_level[NUM_STORMS]);
 /**
- * @brief qed_fw_overlay_mem_alloc - Allocates and fills the FW overlay memory.
+ * qed_fw_overlay_mem_alloc(): Allocates and fills the FW overlay memory.
  *
- * @param p_hwfn - HW device data
- * @param fw_overlay_in_buf - the input FW overlay buffer.
- * @param buf_size - the size of the input FW overlay buffer in bytes.
- *		     must be aligned to dwords.
- * @param fw_overlay_out_mem - OUT: a pointer to the allocated overlays memory.
+ * @p_hwfn: HW device data.
+ * @fw_overlay_in_buf: The input FW overlay buffer.
+ * @buf_size_in_bytes: The size of the input FW overlay buffer in bytes.
+ *		        must be aligned to dwords.
  *
- * @return a pointer to the allocated overlays memory,
+ * Return: A pointer to the allocated overlays memory,
  * or NULL in case of failures.
  */
 struct phys_mem_desc *
 qed_fw_overlay_mem_alloc(struct qed_hwfn *p_hwfn,
-			 const u32 * const fw_overlay_in_buf,
+			 const u32 *const fw_overlay_in_buf,
 			 u32 buf_size_in_bytes);
 
 /**
- * @brief qed_fw_overlay_init_ram - Initializes the FW overlay RAM.
+ * qed_fw_overlay_init_ram(): Initializes the FW overlay RAM.
  *
- * @param p_hwfn - HW device data.
- * @param p_ptt - ptt window used for writing the registers.
- * @param fw_overlay_mem - the allocated FW overlay memory.
+ * @p_hwfn: HW device data.
+ * @p_ptt: Ptt window used for writing the registers.
+ * @fw_overlay_mem: the allocated FW overlay memory.
+ *
+ * Return: Void.
  */
 void qed_fw_overlay_init_ram(struct qed_hwfn *p_hwfn,
 			     struct qed_ptt *p_ptt,
 			     struct phys_mem_desc *fw_overlay_mem);
 
 /**
- * @brief qed_fw_overlay_mem_free - Frees the FW overlay memory.
+ * qed_fw_overlay_mem_free(): Frees the FW overlay memory.
+ *
+ * @p_hwfn: HW device data.
+ * @fw_overlay_mem: The allocated FW overlay memory to free.
  *
- * @param p_hwfn - HW device data.
- * @param fw_overlay_mem - the allocated FW overlay memory to free.
+ * Return: Void.
  */
 void qed_fw_overlay_mem_free(struct qed_hwfn *p_hwfn,
 			     struct phys_mem_desc *fw_overlay_mem);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_hw.c
@@ -23,7 +23,10 @@
 #include "qed_reg_addr.h"
 #include "qed_sriov.h"
 
-#define QED_BAR_ACQUIRE_TIMEOUT 1000
+#define QED_BAR_ACQUIRE_TIMEOUT_USLEEP_CNT	1000
+#define QED_BAR_ACQUIRE_TIMEOUT_USLEEP		1000
+#define QED_BAR_ACQUIRE_TIMEOUT_UDELAY_CNT	100000
+#define QED_BAR_ACQUIRE_TIMEOUT_UDELAY		10
 
 /* Invalid values */
 #define QED_BAR_INVALID_OFFSET          (cpu_to_le32(-1))
@@ -85,11 +88,21 @@
 
 struct qed_ptt *qed_ptt_acquire(struct qed_hwfn *p_hwfn)
 {
+	return qed_ptt_acquire_context(p_hwfn, false);
+}
+
+struct qed_ptt *qed_ptt_acquire_context(struct qed_hwfn *p_hwfn, bool is_atomic)
+{
 	struct qed_ptt *p_ptt;
-	unsigned int i;
+	unsigned int i, count;
+
+	if (is_atomic)
+		count = QED_BAR_ACQUIRE_TIMEOUT_UDELAY_CNT;
+	else
+		count = QED_BAR_ACQUIRE_TIMEOUT_USLEEP_CNT;
 
 	/* Take the free PTT from the list */
-	for (i = 0; i < QED_BAR_ACQUIRE_TIMEOUT; i++) {
+	for (i = 0; i < count; i++) {
 		spin_lock_bh(&p_hwfn->p_ptt_pool->lock);
 
 		if (!list_empty(&p_hwfn->p_ptt_pool->free_list)) {
@@ -105,7 +118,12 @@
 		}
 
 		spin_unlock_bh(&p_hwfn->p_ptt_pool->lock);
-		usleep_range(1000, 2000);
+
+		if (is_atomic)
+			udelay(QED_BAR_ACQUIRE_TIMEOUT_UDELAY);
+		else
+			usleep_range(QED_BAR_ACQUIRE_TIMEOUT_USLEEP,
+				     QED_BAR_ACQUIRE_TIMEOUT_USLEEP * 2);
 	}
 
 	DP_NOTICE(p_hwfn, "PTT acquire timeout - failed to allocate PTT\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_hw.h
@@ -53,85 +53,94 @@
 #define DMAE_MAX_CLIENTS        32
 
 /**
- * @brief qed_gtt_init - Initialize GTT windows
+ * qed_gtt_init(): Initialize GTT windows.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_gtt_init(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ptt_invalidate - Forces all ptt entries to be re-configured
+ * qed_ptt_invalidate(): Forces all ptt entries to be re-configured
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_ptt_invalidate(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ptt_pool_alloc - Allocate and initialize PTT pool
+ * qed_ptt_pool_alloc(): Allocate and initialize PTT pool.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return struct _qed_status - success (0), negative - error.
+ * Return: struct _qed_status - success (0), negative - error.
  */
 int qed_ptt_pool_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ptt_pool_free -
+ * qed_ptt_pool_free(): Free PTT pool.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_ptt_pool_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ptt_get_hw_addr - Get PTT's GRC/HW address
+ * qed_ptt_get_hw_addr(): Get PTT's GRC/HW address.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt
  *
- * @return u32
+ * Return: u32.
  */
 u32 qed_ptt_get_hw_addr(struct qed_hwfn *p_hwfn,
 			struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_ptt_get_bar_addr - Get PPT's external BAR address
+ * qed_ptt_get_bar_addr(): Get PPT's external BAR address.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_ptt: P_ptt
  *
- * @return u32
+ * Return: u32.
  */
 u32 qed_ptt_get_bar_addr(struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_ptt_set_win - Set PTT Window's GRC BAR address
+ * qed_ptt_set_win(): Set PTT Window's GRC BAR address
  *
- * @param p_hwfn
- * @param new_hw_addr
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @new_hw_addr: New HW address.
+ * @p_ptt: P_Ptt
+ *
+ * Return: Void.
  */
 void qed_ptt_set_win(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt,
 		     u32 new_hw_addr);
 
 /**
- * @brief qed_get_reserved_ptt - Get a specific reserved PTT
+ * qed_get_reserved_ptt(): Get a specific reserved PTT.
  *
- * @param p_hwfn
- * @param ptt_idx
+ * @p_hwfn: HW device data.
+ * @ptt_idx: Ptt Index.
  *
- * @return struct qed_ptt *
+ * Return: struct qed_ptt *.
  */
 struct qed_ptt *qed_get_reserved_ptt(struct qed_hwfn *p_hwfn,
 				     enum reserved_ptts ptt_idx);
 
 /**
- * @brief qed_wr - Write value to BAR using the given ptt
+ * qed_wr(): Write value to BAR using the given ptt.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @val: Val.
+ * @hw_addr: HW address
  *
- * @param p_hwfn
- * @param p_ptt
- * @param val
- * @param hw_addr
+ * Return: Void.
  */
 void qed_wr(struct qed_hwfn *p_hwfn,
 	    struct qed_ptt *p_ptt,
@@ -139,26 +148,28 @@
 	    u32 val);
 
 /**
- * @brief qed_rd - Read value from BAR using the given ptt
+ * qed_rd(): Read value from BAR using the given ptt.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param val
- * @param hw_addr
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @hw_addr: HW address
+ *
+ * Return: Void.
  */
 u32 qed_rd(struct qed_hwfn *p_hwfn,
 	   struct qed_ptt *p_ptt,
 	   u32 hw_addr);
 
 /**
- * @brief qed_memcpy_from - copy n bytes from BAR using the given
- *        ptt
+ * qed_memcpy_from(): Copy n bytes from BAR using the given ptt.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @dest: Destination.
+ * @hw_addr: HW address.
+ * @n: N
  *
- * @param p_hwfn
- * @param p_ptt
- * @param dest
- * @param hw_addr
- * @param n
+ * Return: Void.
  */
 void qed_memcpy_from(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt,
@@ -167,14 +178,15 @@
 		     size_t n);
 
 /**
- * @brief qed_memcpy_to - copy n bytes to BAR using the given
- *        ptt
+ * qed_memcpy_to(): Copy n bytes to BAR using the given  ptt
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @hw_addr: HW address.
+ * @src: Source.
+ * @n: N
  *
- * @param p_hwfn
- * @param p_ptt
- * @param hw_addr
- * @param src
- * @param n
+ * Return: Void.
  */
 void qed_memcpy_to(struct qed_hwfn *p_hwfn,
 		   struct qed_ptt *p_ptt,
@@ -182,83 +194,97 @@
 		   void *src,
 		   size_t n);
 /**
- * @brief qed_fid_pretend - pretend to another function when
- *        accessing the ptt window. There is no way to unpretend
- *        a function. The only way to cancel a pretend is to
- *        pretend back to the original function.
- *
- * @param p_hwfn
- * @param p_ptt
- * @param fid - fid field of pxp_pretend structure. Can contain
- *            either pf / vf, port/path fields are don't care.
+ * qed_fid_pretend(): pretend to another function when
+ *                    accessing the ptt window. There is no way to unpretend
+ *                    a function. The only way to cancel a pretend is to
+ *                    pretend back to the original function.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @fid: fid field of pxp_pretend structure. Can contain
+ *        either pf / vf, port/path fields are don't care.
+ *
+ * Return: Void.
  */
 void qed_fid_pretend(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt,
 		     u16 fid);
 
 /**
- * @brief qed_port_pretend - pretend to another port when
- *        accessing the ptt window
+ * qed_port_pretend(): Pretend to another port when accessing the ptt window
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @port_id: The port to pretend to
  *
- * @param p_hwfn
- * @param p_ptt
- * @param port_id - the port to pretend to
+ * Return: Void.
  */
 void qed_port_pretend(struct qed_hwfn *p_hwfn,
 		      struct qed_ptt *p_ptt,
 		      u8 port_id);
 
 /**
- * @brief qed_port_unpretend - cancel any previously set port
- *        pretend
+ * qed_port_unpretend(): Cancel any previously set port pretend
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Void.
  */
 void qed_port_unpretend(struct qed_hwfn *p_hwfn,
 			struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_port_fid_pretend - pretend to another port and another function
- *        when accessing the ptt window
+ * qed_port_fid_pretend(): Pretend to another port and another function
+ *                         when accessing the ptt window
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @port_id: The port to pretend to
+ * @fid: fid field of pxp_pretend structure. Can contain either pf / vf.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param port_id - the port to pretend to
- * @param fid - fid field of pxp_pretend structure. Can contain either pf / vf.
+ * Return: Void.
  */
 void qed_port_fid_pretend(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt, u8 port_id, u16 fid);
 
 /**
- * @brief qed_vfid_to_concrete - build a concrete FID for a
- *        given VF ID
+ * qed_vfid_to_concrete(): Build a concrete FID for a given VF ID
+ *
+ * @p_hwfn: HW device data.
+ * @vfid: VFID.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param vfid
+ * Return: Void.
  */
 u32 qed_vfid_to_concrete(struct qed_hwfn *p_hwfn, u8 vfid);
 
 /**
- * @brief qed_dmae_idx_to_go_cmd - map the idx to dmae cmd
- * this is declared here since other files will require it.
- * @param idx
+ * qed_dmae_idx_to_go_cmd(): Map the idx to dmae cmd
+ *    this is declared here since other files will require it.
+ *
+ * @idx: Index
+ *
+ * Return: Void.
  */
 u32 qed_dmae_idx_to_go_cmd(u8 idx);
 
 /**
- * @brief qed_dmae_info_alloc - Init the dmae_info structure
- * which is part of p_hwfn.
- * @param p_hwfn
+ * qed_dmae_info_alloc(): Init the dmae_info structure
+ *                        which is part of p_hwfn.
+ *
+ * @p_hwfn: HW device data.
+ *
+ * Return: Int.
  */
 int qed_dmae_info_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_dmae_info_free - Free the dmae_info structure
- * which is part of p_hwfn
+ * qed_dmae_info_free(): Free the dmae_info structure
+ *                       which is part of p_hwfn.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_dmae_info_free(struct qed_hwfn *p_hwfn);
 
@@ -292,14 +318,16 @@
 #define QED_HW_ERR_MAX_STR_SIZE 256
 
 /**
- * @brief qed_hw_err_notify - Notify upper layer driver and management FW
- *	about a HW error.
+ * qed_hw_err_notify(): Notify upper layer driver and management FW
+ *                      about a HW error.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @err_type: Err Type.
+ * @fmt: Debug data buffer to send to the MFW
+ * @...: buffer format args
  *
- * @param p_hwfn
- * @param p_ptt
- * @param err_type
- * @param fmt - debug data buffer to send to the MFW
- * @param ... - buffer format args
+ * Return void.
  */
 void __printf(4, 5) __cold qed_hw_err_notify(struct qed_hwfn *p_hwfn,
 					     struct qed_ptt *p_ptt,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_init_ops.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_init_ops.h
@@ -12,23 +12,24 @@
 #include "qed.h"
 
 /**
- * @brief qed_init_iro_array - init iro_arr.
+ * qed_init_iro_array(): init iro_arr.
  *
+ * @cdev: Qed dev pointer.
  *
- * @param cdev
+ * Return: Void.
  */
 void qed_init_iro_array(struct qed_dev *cdev);
 
 /**
- * @brief qed_init_run - Run the init-sequence.
+ * qed_init_run(): Run the init-sequence.
  *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @phase: Phase.
+ * @phase_id: Phase ID.
+ * @modes: Mode.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param phase
- * @param phase_id
- * @param modes
- * @return _qed_status_t
+ * Return: _qed_status_t
  */
 int qed_init_run(struct qed_hwfn *p_hwfn,
 		 struct qed_ptt *p_ptt,
@@ -37,30 +38,31 @@
 		 int modes);
 
 /**
- * @brief qed_init_hwfn_allocate - Allocate RT array, Store 'values' ptrs.
+ * qed_init_alloc(): Allocate RT array, Store 'values' ptrs.
  *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
- *
- * @return _qed_status_t
+ * Return: _qed_status_t.
  */
 int qed_init_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_init_hwfn_deallocate
+ * qed_init_free(): Init HW function deallocate.
  *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_init_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_init_store_rt_reg - Store a configuration value in the RT array.
+ * qed_init_store_rt_reg(): Store a configuration value in the RT array.
  *
+ * @p_hwfn: HW device data.
+ * @rt_offset: RT offset.
+ * @val: Val.
  *
- * @param p_hwfn
- * @param rt_offset
- * @param val
+ * Return: Void.
  */
 void qed_init_store_rt_reg(struct qed_hwfn *p_hwfn,
 			   u32 rt_offset,
@@ -72,15 +74,6 @@
 #define OVERWRITE_RT_REG(hwfn, offset, val) \
 	qed_init_store_rt_reg(hwfn, offset, val)
 
-/**
- * @brief
- *
- *
- * @param p_hwfn
- * @param rt_offset
- * @param val
- * @param size
- */
 void qed_init_store_rt_agg(struct qed_hwfn *p_hwfn,
 			   u32 rt_offset,
 			   u32 *val,
@@ -90,11 +83,12 @@
 	qed_init_store_rt_agg(hwfn, offset, (u32 *)&val, sizeof(val))
 
 /**
- * @brief
- *      Initialize GTT global windows and set admin window
- *      related params of GTT/PTT to default values.
+ * qed_gtt_init(): Initialize GTT global windows and set admin window
+ *                 related params of GTT/PTT to default values.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return Void.
  */
 void qed_gtt_init(struct qed_hwfn *p_hwfn);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_int.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_int.h
@@ -53,51 +53,54 @@
 };
 
 /**
- * @brief qed_int_igu_enable_int - enable device interrupts
+ * qed_int_igu_enable_int(): Enable device interrupts.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param int_mode - interrupt mode to use
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @int_mode: Interrupt mode to use.
+ *
+ * Return: Void.
  */
 void qed_int_igu_enable_int(struct qed_hwfn *p_hwfn,
 			    struct qed_ptt *p_ptt,
 			    enum qed_int_mode int_mode);
 
 /**
- * @brief qed_int_igu_disable_int - disable device interrupts
+ * qed_int_igu_disable_int():  Disable device interrupts.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param p_hwfn
- * @param p_ptt
+ * Return: Void.
  */
 void qed_int_igu_disable_int(struct qed_hwfn *p_hwfn,
 			     struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_int_igu_read_sisr_reg - Reads the single isr multiple dpc
- *        register from igu.
+ * qed_int_igu_read_sisr_reg(): Reads the single isr multiple dpc
+ *                             register from igu.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return u64
+ * Return: u64.
  */
 u64 qed_int_igu_read_sisr_reg(struct qed_hwfn *p_hwfn);
 
 #define QED_SP_SB_ID 0xffff
 /**
- * @brief qed_int_sb_init - Initializes the sb_info structure.
+ * qed_int_sb_init(): Initializes the sb_info structure.
  *
- * once the structure is initialized it can be passed to sb related functions.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @sb_info: points to an uninitialized (but allocated) sb_info structure
+ * @sb_virt_addr: SB Virtual address.
+ * @sb_phy_addr: SB Physial address.
+ * @sb_id: the sb_id to be used (zero based in driver)
+ *           should use QED_SP_SB_ID for SP Status block
  *
- * @param p_hwfn
- * @param p_ptt
- * @param sb_info	points to an uninitialized (but
- *			allocated) sb_info structure
- * @param sb_virt_addr
- * @param sb_phy_addr
- * @param sb_id	the sb_id to be used (zero based in driver)
- *			should use QED_SP_SB_ID for SP Status block
+ * Return: int.
  *
- * @return int
+ * Once the structure is initialized it can be passed to sb related functions.
  */
 int qed_int_sb_init(struct qed_hwfn *p_hwfn,
 		    struct qed_ptt *p_ptt,
@@ -106,82 +109,91 @@
 		    dma_addr_t sb_phy_addr,
 		    u16 sb_id);
 /**
- * @brief qed_int_sb_setup - Setup the sb.
+ * qed_int_sb_setup(): Setup the sb.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param sb_info	initialized sb_info structure
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @sb_info: Initialized sb_info structure.
+ *
+ * Return: Void.
  */
 void qed_int_sb_setup(struct qed_hwfn *p_hwfn,
 		      struct qed_ptt *p_ptt,
 		      struct qed_sb_info *sb_info);
 
 /**
- * @brief qed_int_sb_release - releases the sb_info structure.
+ * qed_int_sb_release(): Releases the sb_info structure.
  *
- * once the structure is released, it's memory can be freed
+ * @p_hwfn: HW device data.
+ * @sb_info: Points to an allocated sb_info structure.
+ * @sb_id: The sb_id to be used (zero based in driver)
+ *         should never be equal to QED_SP_SB_ID
+ *         (SP Status block).
  *
- * @param p_hwfn
- * @param sb_info	points to an allocated sb_info structure
- * @param sb_id		the sb_id to be used (zero based in driver)
- *			should never be equal to QED_SP_SB_ID
- *			(SP Status block)
+ * Return: int.
  *
- * @return int
+ * Once the structure is released, it's memory can be freed.
  */
 int qed_int_sb_release(struct qed_hwfn *p_hwfn,
 		       struct qed_sb_info *sb_info,
 		       u16 sb_id);
 
 /**
- * @brief qed_int_sp_dpc - To be called when an interrupt is received on the
- *        default status block.
+ * qed_int_sp_dpc(): To be called when an interrupt is received on the
+ *                   default status block.
+ *
+ * @t: Tasklet.
  *
- * @param p_hwfn - pointer to hwfn
+ * Return: Void.
  *
  */
 void qed_int_sp_dpc(struct tasklet_struct *t);
 
 /**
- * @brief qed_int_get_num_sbs - get the number of status
- *        blocks configured for this funciton in the igu.
+ * qed_int_get_num_sbs(): Get the number of status blocks configured
+ *                        for this funciton in the igu.
  *
- * @param p_hwfn
- * @param p_sb_cnt_info
+ * @p_hwfn: HW device data.
+ * @p_sb_cnt_info: Pointer to SB count info.
  *
- * @return int - number of status blocks configured
+ * Return: Void.
  */
 void qed_int_get_num_sbs(struct qed_hwfn	*p_hwfn,
 			 struct qed_sb_cnt_info *p_sb_cnt_info);
 
 /**
- * @brief qed_int_disable_post_isr_release - performs the cleanup post ISR
+ * qed_int_disable_post_isr_release(): Performs the cleanup post ISR
  *        release. The API need to be called after releasing all slowpath IRQs
  *        of the device.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
+ * Return: Void.
  */
 void qed_int_disable_post_isr_release(struct qed_dev *cdev);
 
 /**
- * @brief qed_int_attn_clr_enable - sets whether the general behavior is
+ * qed_int_attn_clr_enable: Sets whether the general behavior is
  *        preventing attentions from being reasserted, or following the
  *        attributes of the specific attention.
  *
- * @param cdev
- * @param clr_enable
+ * @cdev: Qed dev pointer.
+ * @clr_enable: Clear enable
+ *
+ * Return: Void.
  *
  */
 void qed_int_attn_clr_enable(struct qed_dev *cdev, bool clr_enable);
 
 /**
- * @brief - Doorbell Recovery handler.
+ * qed_db_rec_handler(): Doorbell Recovery handler.
  *          Run doorbell recovery in case of PF overflow (and flush DORQ if
  *          needed).
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Int.
  */
 int qed_db_rec_handler(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
@@ -223,30 +235,34 @@
 };
 
 /**
- * @brief - Make sure the IGU CAM reflects the resources provided by MFW
+ * qed_int_igu_reset_cam(): Make sure the IGU CAM reflects the resources
+ *                          provided by MFW.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param p_hwfn
- * @param p_ptt
+ * Return: Void.
  */
 int qed_int_igu_reset_cam(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Translate the weakly-defined client sb-id into an IGU sb-id
+ * qed_get_igu_sb_id(): Translate the weakly-defined client sb-id into
+ *                      an IGU sb-id
  *
- * @param p_hwfn
- * @param sb_id - user provided sb_id
+ * @p_hwfn: HW device data.
+ * @sb_id: user provided sb_id.
  *
- * @return an index inside IGU CAM where the SB resides
+ * Return: An index inside IGU CAM where the SB resides.
  */
 u16 qed_get_igu_sb_id(struct qed_hwfn *p_hwfn, u16 sb_id);
 
 /**
- * @brief return a pointer to an unused valid SB
+ * qed_get_igu_free_sb(): Return a pointer to an unused valid SB
  *
- * @param p_hwfn
- * @param b_is_pf - true iff we want a SB belonging to a PF
+ * @p_hwfn: HW device data.
+ * @b_is_pf: True iff we want a SB belonging to a PF.
  *
- * @return point to an igu_block, NULL if none is available
+ * Return: Point to an igu_block, NULL if none is available.
  */
 struct qed_igu_block *qed_get_igu_free_sb(struct qed_hwfn *p_hwfn,
 					  bool b_is_pf);
@@ -259,15 +275,15 @@
 void qed_int_igu_init_rt(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_int_igu_read_cam - Reads the IGU CAM.
+ * qed_int_igu_read_cam():  Reads the IGU CAM.
  *	This function needs to be called during hardware
  *	prepare. It reads the info from igu cam to know which
  *	status block is the default / base status block etc.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int
+ * Return: Int.
  */
 int qed_int_igu_read_cam(struct qed_hwfn *p_hwfn,
 			 struct qed_ptt *p_ptt);
@@ -275,24 +291,22 @@
 typedef int (*qed_int_comp_cb_t)(struct qed_hwfn *p_hwfn,
 				 void *cookie);
 /**
- * @brief qed_int_register_cb - Register callback func for
- *      slowhwfn statusblock.
+ * qed_int_register_cb(): Register callback func for slowhwfn statusblock.
  *
- *	Every protocol that uses the slowhwfn status block
- *	should register a callback function that will be called
- *	once there is an update of the sp status block.
- *
- * @param p_hwfn
- * @param comp_cb - function to be called when there is an
- *                  interrupt on the sp sb
- *
- * @param cookie  - passed to the callback function
- * @param sb_idx  - OUT parameter which gives the chosen index
- *                  for this protocol.
- * @param p_fw_cons  - pointer to the actual address of the
- *                     consumer for this protocol.
- *
- * @return int
+ * @p_hwfn: HW device data.
+ * @comp_cb: Function to be called when there is an
+ *           interrupt on the sp sb
+ * @cookie: Passed to the callback function
+ * @sb_idx: (OUT) parameter which gives the chosen index
+ *           for this protocol.
+ * @p_fw_cons: Pointer to the actual address of the
+ *             consumer for this protocol.
+ *
+ * Return: Int.
+ *
+ * Every protocol that uses the slowhwfn status block
+ * should register a callback function that will be called
+ * once there is an update of the sp status block.
  */
 int qed_int_register_cb(struct qed_hwfn *p_hwfn,
 			qed_int_comp_cb_t comp_cb,
@@ -301,37 +315,40 @@
 			__le16 **p_fw_cons);
 
 /**
- * @brief qed_int_unregister_cb - Unregisters callback
- *      function from sp sb.
- *      Partner of qed_int_register_cb -> should be called
- *      when no longer required.
+ * qed_int_unregister_cb(): Unregisters callback function from sp sb.
+ *
+ * @p_hwfn: HW device data.
+ * @pi: Producer Index.
  *
- * @param p_hwfn
- * @param pi
+ * Return: Int.
  *
- * @return int
+ * Partner of qed_int_register_cb -> should be called
+ * when no longer required.
  */
 int qed_int_unregister_cb(struct qed_hwfn *p_hwfn,
 			  u8 pi);
 
 /**
- * @brief qed_int_get_sp_sb_id - Get the slowhwfn sb id.
+ * qed_int_get_sp_sb_id(): Get the slowhwfn sb id.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return u16
+ * Return: u16.
  */
 u16 qed_int_get_sp_sb_id(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief Status block cleanup. Should be called for each status
- *        block that will be used -> both PF / VF
+ * qed_int_igu_init_pure_rt_single(): Status block cleanup.
+ *                                    Should be called for each status
+ *                                    block that will be used -> both PF / VF.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @igu_sb_id: IGU status block id.
+ * @opaque: Opaque fid of the sb owner.
+ * @b_set: Set(1) / Clear(0).
  *
- * @param p_hwfn
- * @param p_ptt
- * @param igu_sb_id	- igu status block id
- * @param opaque	- opaque fid of the sb owner.
- * @param b_set		- set(1) / clear(0)
+ * Return: Void.
  */
 void qed_int_igu_init_pure_rt_single(struct qed_hwfn *p_hwfn,
 				     struct qed_ptt *p_ptt,
@@ -340,15 +357,16 @@
 				     bool b_set);
 
 /**
- * @brief qed_int_cau_conf - configure cau for a given status
- *        block
+ * qed_int_cau_conf_sb(): Configure cau for a given status block.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @sb_phys: SB Physical.
+ * @igu_sb_id: IGU status block id.
+ * @vf_number: VF number
+ * @vf_valid: VF valid or not.
  *
- * @param p_hwfn
- * @param ptt
- * @param sb_phys
- * @param igu_sb_id
- * @param vf_number
- * @param vf_valid
+ * Return: Void.
  */
 void qed_int_cau_conf_sb(struct qed_hwfn *p_hwfn,
 			 struct qed_ptt *p_ptt,
@@ -358,52 +376,58 @@
 			 u8 vf_valid);
 
 /**
- * @brief qed_int_alloc
+ * qed_int_alloc(): QED interrupt alloc.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int
+ * Return: Int.
  */
 int qed_int_alloc(struct qed_hwfn *p_hwfn,
 		  struct qed_ptt *p_ptt);
 
 /**
- * @brief qed_int_free
+ * qed_int_free(): QED interrupt free.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_int_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_int_setup
+ * qed_int_setup(): QED interrupt setup.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param p_hwfn
- * @param p_ptt
+ * Return: Void.
  */
 void qed_int_setup(struct qed_hwfn *p_hwfn,
 		   struct qed_ptt *p_ptt);
 
 /**
- * @brief - Enable Interrupt & Attention for hw function
+ * qed_int_igu_enable(): Enable Interrupt & Attention for hw function.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param int_mode
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @int_mode: Interrut mode
  *
- * @return int
+ * Return: Int.
  */
 int qed_int_igu_enable(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt,
 		       enum qed_int_mode int_mode);
 
 /**
- * @brief - Initialize CAU status block entry
+ * qed_init_cau_sb_entry(): Initialize CAU status block entry.
+ *
+ * @p_hwfn: HW device data.
+ * @p_sb_entry: Pointer SB entry.
+ * @pf_id: PF number
+ * @vf_number: VF number
+ * @vf_valid: VF valid or not.
  *
- * @param p_hwfn
- * @param p_sb_entry
- * @param pf_id
- * @param vf_number
- * @param vf_valid
+ * Return: Void.
  */
 void qed_init_cau_sb_entry(struct qed_hwfn *p_hwfn,
 			   struct cau_sb_entry *p_sb_entry,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_iscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_iscsi.c
@@ -1000,13 +1000,14 @@
 }
 
 static int qed_iscsi_get_stats(struct qed_hwfn *p_hwfn,
-			       struct qed_iscsi_stats *stats)
+			       struct qed_iscsi_stats *stats,
+			       bool is_atomic)
 {
 	struct qed_ptt *p_ptt;
 
 	memset(stats, 0, sizeof(*stats));
 
-	p_ptt = qed_ptt_acquire(p_hwfn);
+	p_ptt = qed_ptt_acquire_context(p_hwfn, is_atomic);
 	if (!p_ptt) {
 		DP_ERR(p_hwfn, "Failed to acquire ptt\n");
 		return -EAGAIN;
@@ -1337,9 +1338,16 @@
 					   QED_SPQ_MODE_EBLOCK, NULL);
 }
 
+static int qed_iscsi_stats_context(struct qed_dev *cdev,
+				   struct qed_iscsi_stats *stats,
+				   bool is_atomic)
+{
+	return qed_iscsi_get_stats(QED_AFFIN_HWFN(cdev), stats, is_atomic);
+}
+
 static int qed_iscsi_stats(struct qed_dev *cdev, struct qed_iscsi_stats *stats)
 {
-	return qed_iscsi_get_stats(QED_AFFIN_HWFN(cdev), stats);
+	return qed_iscsi_stats_context(cdev, stats, false);
 }
 
 static int qed_iscsi_change_mac(struct qed_dev *cdev,
@@ -1359,13 +1367,14 @@
 }
 
 void qed_get_protocol_stats_iscsi(struct qed_dev *cdev,
-				  struct qed_mcp_iscsi_stats *stats)
+				  struct qed_mcp_iscsi_stats *stats,
+				  bool is_atomic)
 {
 	struct qed_iscsi_stats proto_stats;
 
 	/* Retrieve FW statistics */
 	memset(&proto_stats, 0, sizeof(proto_stats));
-	if (qed_iscsi_stats(cdev, &proto_stats)) {
+	if (qed_iscsi_stats_context(cdev, &proto_stats, is_atomic)) {
 		DP_VERBOSE(cdev, QED_MSG_STORAGE,
 			   "Failed to collect ISCSI statistics\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_iscsi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_iscsi.h
@@ -34,13 +34,19 @@
 void qed_iscsi_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief - Fills provided statistics struct with statistics.
+ * qed_get_protocol_stats_iscsi(): Fills provided statistics
+ *                                 struct with statistics.
  *
- * @param cdev
- * @param stats - points to struct that will be filled with statistics.
+ * @cdev: Qed dev pointer.
+ * @stats: Points to struct that will be filled with statistics.
+ * @is_atomic: Hint from the caller - if the func can sleep or not.
+ *
+ * Context: The function should not sleep in case is_atomic == true.
+ * Return: Void.
  */
 void qed_get_protocol_stats_iscsi(struct qed_dev *cdev,
-				  struct qed_mcp_iscsi_stats *stats);
+				  struct qed_mcp_iscsi_stats *stats,
+				  bool is_atomic);
 #else /* IS_ENABLED(CONFIG_QED_ISCSI) */
 static inline int qed_iscsi_alloc(struct qed_hwfn *p_hwfn)
 {
@@ -53,7 +59,8 @@
 
 static inline void
 qed_get_protocol_stats_iscsi(struct qed_dev *cdev,
-			     struct qed_mcp_iscsi_stats *stats) {}
+			     struct qed_mcp_iscsi_stats *stats,
+			     bool is_atomic) {}
 #endif /* IS_ENABLED(CONFIG_QED_ISCSI) */
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_l2.c
@@ -1863,7 +1863,8 @@
 }
 
 static void _qed_get_vport_stats(struct qed_dev *cdev,
-				 struct qed_eth_stats *stats)
+				 struct qed_eth_stats *stats,
+				 bool is_atomic)
 {
 	u8 fw_vport = 0;
 	int i;
@@ -1872,10 +1873,11 @@
 
 	for_each_hwfn(cdev, i) {
 		struct qed_hwfn *p_hwfn = &cdev->hwfns[i];
-		struct qed_ptt *p_ptt = IS_PF(cdev) ? qed_ptt_acquire(p_hwfn)
-						    :  NULL;
+		struct qed_ptt *p_ptt;
 		bool b_get_port_stats;
 
+		p_ptt = IS_PF(cdev) ? qed_ptt_acquire_context(p_hwfn, is_atomic)
+				    : NULL;
 		if (IS_PF(cdev)) {
 			/* The main vport index is relative first */
 			if (qed_fw_vport(p_hwfn, 0, &fw_vport)) {
@@ -1901,14 +1903,21 @@
 
 void qed_get_vport_stats(struct qed_dev *cdev, struct qed_eth_stats *stats)
 {
+	qed_get_vport_stats_context(cdev, stats, false);
+}
+
+void qed_get_vport_stats_context(struct qed_dev *cdev,
+				 struct qed_eth_stats *stats,
+				 bool is_atomic)
+{
 	u32 i;
 
-	if (!cdev) {
+	if (!cdev || cdev->recov_in_prog) {
 		memset(stats, 0, sizeof(*stats));
 		return;
 	}
 
-	_qed_get_vport_stats(cdev, stats);
+	_qed_get_vport_stats(cdev, stats, is_atomic);
 
 	if (!cdev->reset_stats)
 		return;
@@ -1960,7 +1969,7 @@
 	if (!cdev->reset_stats) {
 		DP_INFO(cdev, "Reset stats not allocated\n");
 	} else {
-		_qed_get_vport_stats(cdev, cdev->reset_stats);
+		_qed_get_vport_stats(cdev, cdev->reset_stats, false);
 		cdev->reset_stats->common.link_change_count = 0;
 	}
 }
@@ -2763,25 +2772,6 @@
 	return qed_filter_mcast_cmd(cdev, &mcast, QED_SPQ_MODE_CB, NULL);
 }
 
-static int qed_configure_filter(struct qed_dev *cdev,
-				struct qed_filter_params *params)
-{
-	enum qed_filter_rx_mode_type accept_flags;
-
-	switch (params->type) {
-	case QED_FILTER_TYPE_UCAST:
-		return qed_configure_filter_ucast(cdev, &params->filter.ucast);
-	case QED_FILTER_TYPE_MCAST:
-		return qed_configure_filter_mcast(cdev, &params->filter.mcast);
-	case QED_FILTER_TYPE_RX_MODE:
-		accept_flags = params->filter.accept_flags;
-		return qed_configure_filter_rx_mode(cdev, accept_flags);
-	default:
-		DP_NOTICE(cdev, "Unknown filter type %d\n", (int)params->type);
-		return -EINVAL;
-	}
-}
-
 static int qed_configure_arfs_searcher(struct qed_dev *cdev,
 				       enum qed_filter_config_mode mode)
 {
@@ -2867,7 +2857,7 @@
 				      cqe);
 }
 
-static int qed_req_bulletin_update_mac(struct qed_dev *cdev, u8 *mac)
+static int qed_req_bulletin_update_mac(struct qed_dev *cdev, const u8 *mac)
 {
 	int i, ret;
 
@@ -2904,7 +2894,9 @@
 	.q_rx_stop = &qed_stop_rxq,
 	.q_tx_start = &qed_start_txq,
 	.q_tx_stop = &qed_stop_txq,
-	.filter_config = &qed_configure_filter,
+	.filter_config_rx_mode = &qed_configure_filter_rx_mode,
+	.filter_config_ucast = &qed_configure_filter_ucast,
+	.filter_config_mcast = &qed_configure_filter_mcast,
 	.fastpath_stop = &qed_fastpath_stop,
 	.eth_cqe_completion = &qed_fp_cqe_completion,
 	.get_vport_stats = &qed_get_vport_stats,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_l2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_l2.h
@@ -92,18 +92,18 @@
 };
 
 /**
- * @brief qed_eth_rx_queue_stop - This ramrod closes an Rx queue
+ * qed_eth_rx_queue_stop(): This ramrod closes an Rx queue.
  *
- * @param p_hwfn
- * @param p_rxq			Handler of queue to close
- * @param eq_completion_only	If True completion will be on
- *				EQe, if False completion will be
- *				on EQe if p_hwfn opaque
- *				different from the RXQ opaque
- *				otherwise on CQe.
- * @param cqe_completion	If True completion will be
- *				receive on CQe.
- * @return int
+ * @p_hwfn: HW device data.
+ * @p_rxq: Handler of queue to close
+ * @eq_completion_only: If True completion will be on
+ *                      EQe, if False completion will be
+ *                      on EQe if p_hwfn opaque
+ *                      different from the RXQ opaque
+ *                      otherwise on CQe.
+ * @cqe_completion: If True completion will be receive on CQe.
+ *
+ * Return: Int.
  */
 int
 qed_eth_rx_queue_stop(struct qed_hwfn *p_hwfn,
@@ -111,12 +111,12 @@
 		      bool eq_completion_only, bool cqe_completion);
 
 /**
- * @brief qed_eth_tx_queue_stop - closes a Tx queue
+ * qed_eth_tx_queue_stop(): Closes a Tx queue.
  *
- * @param p_hwfn
- * @param p_txq - handle to Tx queue needed to be closed
+ * @p_hwfn: HW device data.
+ * @p_txq: handle to Tx queue needed to be closed.
  *
- * @return int
+ * Return: Int.
  */
 int qed_eth_tx_queue_stop(struct qed_hwfn *p_hwfn, void *p_txq);
 
@@ -205,16 +205,15 @@
 			struct qed_spq_comp_cb *p_comp_data);
 
 /**
- * @brief qed_sp_vport_stop -
- *
- * This ramrod closes a VPort after all its RX and TX queues are terminated.
- * An Assert is generated if any queues are left open.
+ * qed_sp_vport_stop: This ramrod closes a VPort after all its
+ *                    RX and TX queues are terminated.
+ *                    An Assert is generated if any queues are left open.
+ *
+ * @p_hwfn: HW device data.
+ * @opaque_fid: Opaque FID
+ * @vport_id: VPort ID.
  *
- * @param p_hwfn
- * @param opaque_fid
- * @param vport_id VPort ID
- *
- * @return int
+ * Return: Int.
  */
 int qed_sp_vport_stop(struct qed_hwfn *p_hwfn, u16 opaque_fid, u8 vport_id);
 
@@ -225,22 +224,21 @@
 			    struct qed_spq_comp_cb *p_comp_data);
 
 /**
- * @brief qed_sp_rx_eth_queues_update -
- *
- * This ramrod updates an RX queue. It is used for setting the active state
- * of the queue and updating the TPA and SGE parameters.
+ * qed_sp_eth_rx_queues_update(): This ramrod updates an RX queue.
+ *                                It is used for setting the active state
+ *                                of the queue and updating the TPA and
+ *                                SGE parameters.
+ * @p_hwfn: HW device data.
+ * @pp_rxq_handlers: An array of queue handlers to be updated.
+ * @num_rxqs: number of queues to update.
+ * @complete_cqe_flg: Post completion to the CQE Ring if set.
+ * @complete_event_flg: Post completion to the Event Ring if set.
+ * @comp_mode: Comp mode.
+ * @p_comp_data: Pointer Comp data.
  *
- * @note At the moment - only used by non-linux VFs.
+ * Return: Int.
  *
- * @param p_hwfn
- * @param pp_rxq_handlers	An array of queue handlers to be updated.
- * @param num_rxqs              number of queues to update.
- * @param complete_cqe_flg	Post completion to the CQE Ring if set
- * @param complete_event_flg	Post completion to the Event Ring if set
- * @param comp_mode
- * @param p_comp_data
- *
- * @return int
+ * Note At the moment - only used by non-linux VFs.
  */
 
 int
@@ -252,35 +250,61 @@
 			    enum spq_mode comp_mode,
 			    struct qed_spq_comp_cb *p_comp_data);
 
+/**
+ * qed_get_vport_stats(): Fills provided statistics
+ *			  struct with statistics.
+ *
+ * @cdev: Qed dev pointer.
+ * @stats: Points to struct that will be filled with statistics.
+ *
+ * Return: Void.
+ */
 void qed_get_vport_stats(struct qed_dev *cdev, struct qed_eth_stats *stats);
 
-void qed_reset_vport_stats(struct qed_dev *cdev);
-
 /**
- * *@brief qed_arfs_mode_configure -
+ * qed_get_vport_stats_context(): Fills provided statistics
+ *				  struct with statistics.
  *
- **Enable or disable rfs mode. It must accept atleast one of tcp or udp true
- **and atleast one of ipv4 or ipv6 true to enable rfs mode.
+ * @cdev: Qed dev pointer.
+ * @stats: Points to struct that will be filled with statistics.
+ * @is_atomic: Hint from the caller - if the func can sleep or not.
  *
- **@param p_hwfn
- **@param p_ptt
- **@param p_cfg_params - arfs mode configuration parameters.
+ * Context: The function should not sleep in case is_atomic == true.
+ * Return: Void.
+ */
+void qed_get_vport_stats_context(struct qed_dev *cdev,
+				 struct qed_eth_stats *stats,
+				 bool is_atomic);
+
+void qed_reset_vport_stats(struct qed_dev *cdev);
+
+/**
+ * qed_arfs_mode_configure(): Enable or disable rfs mode.
+ *                            It must accept at least one of tcp or udp true
+ *                            and at least one of ipv4 or ipv6 true to enable
+ *                            rfs mode.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_cfg_params: arfs mode configuration parameters.
  *
+ * Return. Void.
  */
 void qed_arfs_mode_configure(struct qed_hwfn *p_hwfn,
 			     struct qed_ptt *p_ptt,
 			     struct qed_arfs_config_params *p_cfg_params);
 
 /**
- * @brief - qed_configure_rfs_ntuple_filter
+ * qed_configure_rfs_ntuple_filter(): This ramrod should be used to add
+ *                                     or remove arfs hw filter
  *
- * This ramrod should be used to add or remove arfs hw filter
+ * @p_hwfn: HW device data.
+ * @p_cb: Used for QED_SPQ_MODE_CB,where client would initialize
+ *        it with cookie and callback function address, if not
+ *        using this mode then client must pass NULL.
+ * @p_params: Pointer to params.
  *
- * @params p_hwfn
- * @params p_cb - Used for QED_SPQ_MODE_CB,where client would initialize
- *		  it with cookie and callback function address, if not
- *		  using this mode then client must pass NULL.
- * @params p_params
+ * Return: Void.
  */
 int
 qed_configure_rfs_ntuple_filter(struct qed_hwfn *p_hwfn,
@@ -374,16 +398,17 @@
 		       struct qed_sp_vport_start_params *p_params);
 
 /**
- * @brief - Starts an Rx queue, when queue_cid is already prepared
+ * qed_eth_rxq_start_ramrod(): Starts an Rx queue, when queue_cid is
+ *                             already prepared
  *
- * @param p_hwfn
- * @param p_cid
- * @param bd_max_bytes
- * @param bd_chain_phys_addr
- * @param cqe_pbl_addr
- * @param cqe_pbl_size
+ * @p_hwfn: HW device data.
+ * @p_cid: Pointer CID.
+ * @bd_max_bytes: Max bytes.
+ * @bd_chain_phys_addr: Chain physcial address.
+ * @cqe_pbl_addr: PBL address.
+ * @cqe_pbl_size: PBL size.
  *
- * @return int
+ * Return: Int.
  */
 int
 qed_eth_rxq_start_ramrod(struct qed_hwfn *p_hwfn,
@@ -393,15 +418,16 @@
 			 dma_addr_t cqe_pbl_addr, u16 cqe_pbl_size);
 
 /**
- * @brief - Starts a Tx queue, where queue_cid is already prepared
+ * qed_eth_txq_start_ramrod(): Starts a Tx queue, where queue_cid is
+ *                             already prepared
  *
- * @param p_hwfn
- * @param p_cid
- * @param pbl_addr
- * @param pbl_size
- * @param p_pq_params - parameters for choosing the PQ for this Tx queue
+ * @p_hwfn: HW device data.
+ * @p_cid: Pointer CID.
+ * @pbl_addr: PBL address.
+ * @pbl_size: PBL size.
+ * @pq_id: Parameters for choosing the PQ for this Tx queue.
  *
- * @return int
+ * Return: Int.
  */
 int
 qed_eth_txq_start_ramrod(struct qed_hwfn *p_hwfn,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_ll2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_ll2.c
@@ -87,7 +87,10 @@
 static int qed_ll2_alloc_buffer(struct qed_dev *cdev,
 				u8 **data, dma_addr_t *phys_addr)
 {
-	*data = kmalloc(cdev->ll2->rx_size, GFP_ATOMIC);
+	size_t size = cdev->ll2->rx_size + NET_SKB_PAD +
+		      SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+
+	*data = kmalloc(size, GFP_ATOMIC);
 	if (!(*data)) {
 		DP_INFO(cdev, "Failed to allocate LL2 buffer data\n");
 		return -ENOMEM;
@@ -2548,7 +2551,7 @@
 	INIT_LIST_HEAD(&cdev->ll2->list);
 	spin_lock_init(&cdev->ll2->lock);
 
-	cdev->ll2->rx_size = NET_SKB_PAD + ETH_HLEN +
+	cdev->ll2->rx_size = PRM_DMA_PAD_BYTES_NUM + ETH_HLEN +
 			     L1_CACHE_BYTES + params->mtu;
 
 	/* Allocate memory for LL2.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_ll2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_ll2.h
@@ -111,49 +111,49 @@
 	enum core_tx_dest tx_dest;
 	u8 tx_stats_en;
 	bool main_func_queue;
+	struct qed_ll2_cbs cbs;
 	struct qed_ll2_rx_queue rx_queue;
 	struct qed_ll2_tx_queue tx_queue;
-	struct qed_ll2_cbs cbs;
 };
 
 extern const struct qed_ll2_ops qed_ll2_ops_pass;
 
 /**
- * @brief qed_ll2_acquire_connection - allocate resources,
- *        starts rx & tx (if relevant) queues pair. Provides
- *        connecion handler as output parameter.
+ * qed_ll2_acquire_connection(): Allocate resources,
+ *                               starts rx & tx (if relevant) queues pair.
+ *                               Provides connecion handler as output
+ *                               parameter.
  *
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @data: Describes connection parameters.
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param data - describes connection parameters
- * @return int
+ * Return: Int.
  */
 int qed_ll2_acquire_connection(void *cxt, struct qed_ll2_acquire_data *data);
 
 /**
- * @brief qed_ll2_establish_connection - start previously
- *        allocated LL2 queues pair
+ * qed_ll2_establish_connection(): start previously allocated LL2 queues pair
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param p_ptt
- * @param connection_handle	LL2 connection's handle obtained from
- *                              qed_ll2_require_connection
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: LL2 connection's handle obtained from
+ *                     qed_ll2_require_connection.
  *
- * @return 0 on success, failure otherwise
+ * Return: 0 on success, failure otherwise.
  */
 int qed_ll2_establish_connection(void *cxt, u8 connection_handle);
 
 /**
- * @brief qed_ll2_post_rx_buffers - submit buffers to LL2 Rx queue.
+ * qed_ll2_post_rx_buffer(): Submit buffers to LL2 Rx queue.
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param connection_handle	LL2 connection's handle obtained from
- *				qed_ll2_require_connection
- * @param addr			rx (physical address) buffers to submit
- * @param cookie
- * @param notify_fw		produce corresponding Rx BD immediately
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: LL2 connection's handle obtained from
+ *                     qed_ll2_require_connection.
+ * @addr: RX (physical address) buffers to submit.
+ * @buf_len: Buffer Len.
+ * @cookie: Cookie.
+ * @notify_fw: Produce corresponding Rx BD immediately.
  *
- * @return 0 on success, failure otherwise
+ * Return: 0 on success, failure otherwise.
  */
 int qed_ll2_post_rx_buffer(void *cxt,
 			   u8 connection_handle,
@@ -161,15 +161,15 @@
 			   u16 buf_len, void *cookie, u8 notify_fw);
 
 /**
- * @brief qed_ll2_prepare_tx_packet - request for start Tx BD
- *				      to prepare Tx packet submission to FW.
+ * qed_ll2_prepare_tx_packet(): Request for start Tx BD
+ *				to prepare Tx packet submission to FW.
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param connection_handle
- * @param pkt - info regarding the tx packet
- * @param notify_fw - issue doorbell to fw for this packet
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: Connection handle.
+ * @pkt: Info regarding the tx packet.
+ * @notify_fw: Issue doorbell to fw for this packet.
  *
- * @return 0 on success, failure otherwise
+ * Return: 0 on success, failure otherwise.
  */
 int qed_ll2_prepare_tx_packet(void *cxt,
 			      u8 connection_handle,
@@ -177,81 +177,83 @@
 			      bool notify_fw);
 
 /**
- * @brief qed_ll2_release_connection -	releases resources
- *					allocated for LL2 connection
+ * qed_ll2_release_connection(): Releases resources allocated for LL2
+ *                               connection.
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param connection_handle		LL2 connection's handle obtained from
- *					qed_ll2_require_connection
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: LL2 connection's handle obtained from
+ *                     qed_ll2_require_connection.
+ *
+ * Return: Void.
  */
 void qed_ll2_release_connection(void *cxt, u8 connection_handle);
 
 /**
- * @brief qed_ll2_set_fragment_of_tx_packet -	provides fragments to fill
- *						Tx BD of BDs requested by
- *						qed_ll2_prepare_tx_packet
- *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param connection_handle			LL2 connection's handle
- *						obtained from
- *						qed_ll2_require_connection
- * @param addr
- * @param nbytes
+ * qed_ll2_set_fragment_of_tx_packet(): Provides fragments to fill
+ *                                      Tx BD of BDs requested by
+ *                                      qed_ll2_prepare_tx_packet
+ *
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: LL2 connection's handle obtained from
+ *                     qed_ll2_require_connection.
+ * @addr: Address.
+ * @nbytes: Number of bytes.
  *
- * @return 0 on success, failure otherwise
+ * Return: 0 on success, failure otherwise.
  */
 int qed_ll2_set_fragment_of_tx_packet(void *cxt,
 				      u8 connection_handle,
 				      dma_addr_t addr, u16 nbytes);
 
 /**
- * @brief qed_ll2_terminate_connection -	stops Tx/Rx queues
- *
+ * qed_ll2_terminate_connection(): Stops Tx/Rx queues
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param connection_handle			LL2 connection's handle
- *						obtained from
- *						qed_ll2_require_connection
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: LL2 connection's handle obtained from
+ *                    qed_ll2_require_connection.
  *
- * @return 0 on success, failure otherwise
+ * Return: 0 on success, failure otherwise.
  */
 int qed_ll2_terminate_connection(void *cxt, u8 connection_handle);
 
 /**
- * @brief qed_ll2_get_stats -	get LL2 queue's statistics
+ * qed_ll2_get_stats(): Get LL2 queue's statistics
  *
+ * @cxt: Pointer to the hw-function [opaque to some].
+ * @connection_handle: LL2 connection's handle obtained from
+ *                    qed_ll2_require_connection.
+ * @p_stats: Pointer Status.
  *
- * @param cxt - pointer to the hw-function [opaque to some]
- * @param connection_handle	LL2 connection's handle obtained from
- *				qed_ll2_require_connection
- * @param p_stats
- *
- * @return 0 on success, failure otherwise
+ * Return: 0 on success, failure otherwise.
  */
 int qed_ll2_get_stats(void *cxt,
 		      u8 connection_handle, struct qed_ll2_stats *p_stats);
 
 /**
- * @brief qed_ll2_alloc - Allocates LL2 connections set
+ * qed_ll2_alloc(): Allocates LL2 connections set.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_ll2_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ll2_setup - Inits LL2 connections set
+ * qed_ll2_setup(): Inits LL2 connections set.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  *
  */
 void qed_ll2_setup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_ll2_free - Releases LL2 connections set
+ * qed_ll2_free(): Releases LL2 connections set
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  *
  */
 void qed_ll2_free(struct qed_hwfn *p_hwfn);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_main.c
@@ -1238,7 +1238,6 @@
 static int qed_slowpath_wq_start(struct qed_dev *cdev)
 {
 	struct qed_hwfn *hwfn;
-	char name[NAME_SIZE];
 	int i;
 
 	if (IS_VF(cdev))
@@ -1247,11 +1246,11 @@
 	for_each_hwfn(cdev, i) {
 		hwfn = &cdev->hwfns[i];
 
-		snprintf(name, NAME_SIZE, "slowpath-%02x:%02x.%02x",
-			 cdev->pdev->bus->number,
-			 PCI_SLOT(cdev->pdev->devfn), hwfn->abs_pf_id);
+		hwfn->slowpath_wq = alloc_workqueue("slowpath-%02x:%02x.%02x",
+					 0, 0, cdev->pdev->bus->number,
+					 PCI_SLOT(cdev->pdev->devfn),
+					 hwfn->abs_pf_id);
 
-		hwfn->slowpath_wq = alloc_workqueue(name, 0, 0);
 		if (!hwfn->slowpath_wq) {
 			DP_NOTICE(hwfn, "Cannot create slowpath workqueue\n");
 			return -ENOMEM;
@@ -2892,7 +2891,7 @@
 	return status;
 }
 
-static int qed_update_mac(struct qed_dev *cdev, u8 *mac)
+static int qed_update_mac(struct qed_dev *cdev, const u8 *mac)
 {
 	struct qed_hwfn *hwfn = QED_LEADING_HWFN(cdev);
 	struct qed_ptt *ptt;
@@ -3054,7 +3053,7 @@
 
 	switch (type) {
 	case QED_MCP_LAN_STATS:
-		qed_get_vport_stats(cdev, &eth_stats);
+		qed_get_vport_stats_context(cdev, &eth_stats, true);
 		stats->lan_stats.ucast_rx_pkts =
 					eth_stats.common.rx_ucast_pkts;
 		stats->lan_stats.ucast_tx_pkts =
@@ -3062,10 +3061,10 @@
 		stats->lan_stats.fcs_err = -1;
 		break;
 	case QED_MCP_FCOE_STATS:
-		qed_get_protocol_stats_fcoe(cdev, &stats->fcoe_stats);
+		qed_get_protocol_stats_fcoe(cdev, &stats->fcoe_stats, true);
 		break;
 	case QED_MCP_ISCSI_STATS:
-		qed_get_protocol_stats_iscsi(cdev, &stats->iscsi_stats);
+		qed_get_protocol_stats_iscsi(cdev, &stats->iscsi_stats, true);
 		break;
 	default:
 		DP_VERBOSE(cdev, QED_MSG_SP,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_mcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_mcp.c
@@ -2854,7 +2854,7 @@
 }
 
 int qed_mcp_ov_update_mac(struct qed_hwfn *p_hwfn,
-			  struct qed_ptt *p_ptt, u8 *mac)
+			  struct qed_ptt *p_ptt, const u8 *mac)
 {
 	struct qed_mcp_mb_params mb_params;
 	u32 mfw_mac[2];
@@ -3253,7 +3253,9 @@
 	if (rc)
 		return rc;
 
-	if (((rsp & FW_MSG_CODE_MASK) != FW_MSG_CODE_OK))
+	if (((rsp & FW_MSG_CODE_MASK) == FW_MSG_CODE_UNSUPPORTED))
+		rc = -EOPNOTSUPP;
+	else if (((rsp & FW_MSG_CODE_MASK) != FW_MSG_CODE_OK))
 		rc = -EINVAL;
 
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_mcp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_mcp.h
@@ -266,97 +266,97 @@
 #define QED_NVM_CFG_OPTION_ENTITY_SEL	BIT(4)
 
 /**
- * @brief - returns the link params of the hw function
+ * qed_mcp_get_link_params(): Returns the link params of the hw function.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @returns pointer to link params
+ * Returns: Pointer to link params.
  */
-struct qed_mcp_link_params *qed_mcp_get_link_params(struct qed_hwfn *);
+struct qed_mcp_link_params *qed_mcp_get_link_params(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief - return the link state of the hw function
+ * qed_mcp_get_link_state(): Return the link state of the hw function.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @returns pointer to link state
+ * Returns: Pointer to link state.
  */
-struct qed_mcp_link_state *qed_mcp_get_link_state(struct qed_hwfn *);
+struct qed_mcp_link_state *qed_mcp_get_link_state(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief - return the link capabilities of the hw function
+ * qed_mcp_get_link_capabilities(): Return the link capabilities of the
+ *                                  hw function.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @returns pointer to link capabilities
+ * Returns: Pointer to link capabilities.
  */
 struct qed_mcp_link_capabilities
 	*qed_mcp_get_link_capabilities(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief Request the MFW to set the the link according to 'link_input'.
+ * qed_mcp_set_link(): Request the MFW to set the link according
+ *                     to 'link_input'.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param b_up - raise link if `true'. Reset link if `false'.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @b_up: Raise link if `true'. Reset link if `false'.
  *
- * @return int
+ * Return: Int.
  */
 int qed_mcp_set_link(struct qed_hwfn   *p_hwfn,
 		     struct qed_ptt     *p_ptt,
 		     bool               b_up);
 
 /**
- * @brief Get the management firmware version value
+ * qed_mcp_get_mfw_ver(): Get the management firmware version value.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_mfw_ver    - mfw version value
- * @param p_running_bundle_id	- image id in nvram; Optional.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_mfw_ver: MFW version value.
+ * @p_running_bundle_id: Image id in nvram; Optional.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - operation was successful.
  */
 int qed_mcp_get_mfw_ver(struct qed_hwfn *p_hwfn,
 			struct qed_ptt *p_ptt,
 			u32 *p_mfw_ver, u32 *p_running_bundle_id);
 
 /**
- * @brief Get the MBI version value
+ * qed_mcp_get_mbi_ver(): Get the MBI version value.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_mbi_ver - A pointer to a variable to be filled with the MBI version.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_mbi_ver: A pointer to a variable to be filled with the MBI version.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - operation was successful.
  */
 int qed_mcp_get_mbi_ver(struct qed_hwfn *p_hwfn,
 			struct qed_ptt *p_ptt, u32 *p_mbi_ver);
 
 /**
- * @brief Get media type value of the port.
+ * qed_mcp_get_media_type(): Get media type value of the port.
  *
- * @param cdev      - qed dev pointer
- * @param p_ptt
- * @param mfw_ver    - media type value
- *
- * @return int -
- *      0 - Operation was successul.
- *      -EBUSY - Operation failed
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @media_type: Media type value
+ *
+ * Return: Int - 0 - Operation was successul.
+ *              -EBUSY - Operation failed
  */
 int qed_mcp_get_media_type(struct qed_hwfn *p_hwfn,
 			   struct qed_ptt *p_ptt, u32 *media_type);
 
 /**
- * @brief Get transceiver data of the port.
+ * qed_mcp_get_transceiver_data(): Get transceiver data of the port.
  *
- * @param cdev      - qed dev pointer
- * @param p_ptt
- * @param p_transceiver_state - transceiver state.
- * @param p_transceiver_type - media type value
- *
- * @return int -
- *      0 - Operation was successful.
- *      -EBUSY - Operation failed
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_transceiver_state: Transceiver state.
+ * @p_tranceiver_type: Media type value.
+ *
+ * Return: Int - 0 - Operation was successul.
+ *              -EBUSY - Operation failed
  */
 int qed_mcp_get_transceiver_data(struct qed_hwfn *p_hwfn,
 				 struct qed_ptt *p_ptt,
@@ -364,50 +364,48 @@
 				 u32 *p_tranceiver_type);
 
 /**
- * @brief Get transceiver supported speed mask.
+ * qed_mcp_trans_speed_mask(): Get transceiver supported speed mask.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_speed_mask: Bit mask of all supported speeds.
  *
- * @param cdev      - qed dev pointer
- * @param p_ptt
- * @param p_speed_mask - Bit mask of all supported speeds.
- *
- * @return int -
- *      0 - Operation was successful.
- *      -EBUSY - Operation failed
+ * Return: Int - 0 - Operation was successul.
+ *              -EBUSY - Operation failed
  */
 
 int qed_mcp_trans_speed_mask(struct qed_hwfn *p_hwfn,
 			     struct qed_ptt *p_ptt, u32 *p_speed_mask);
 
 /**
- * @brief Get board configuration.
+ * qed_mcp_get_board_config(): Get board configuration.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_board_config: Board config.
  *
- * @param cdev      - qed dev pointer
- * @param p_ptt
- * @param p_board_config - Board config.
- *
- * @return int -
- *      0 - Operation was successful.
- *      -EBUSY - Operation failed
+ * Return: Int - 0 - Operation was successul.
+ *              -EBUSY - Operation failed
  */
 int qed_mcp_get_board_config(struct qed_hwfn *p_hwfn,
 			     struct qed_ptt *p_ptt, u32 *p_board_config);
 
 /**
- * @brief General function for sending commands to the MCP
- *        mailbox. It acquire mutex lock for the entire
- *        operation, from sending the request until the MCP
- *        response. Waiting for MCP response will be checked up
- *        to 5 seconds every 5ms.
- *
- * @param p_hwfn     - hw function
- * @param p_ptt      - PTT required for register access
- * @param cmd        - command to be sent to the MCP.
- * @param param      - Optional param
- * @param o_mcp_resp - The MCP response code (exclude sequence).
- * @param o_mcp_param- Optional parameter provided by the MCP
+ * qed_mcp_cmd(): General function for sending commands to the MCP
+ *                mailbox. It acquire mutex lock for the entire
+ *                operation, from sending the request until the MCP
+ *                response. Waiting for MCP response will be checked up
+ *                to 5 seconds every 5ms.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ * @cmd: command to be sent to the MCP.
+ * @param: Optional param
+ * @o_mcp_resp: The MCP response code (exclude sequence).
+ * @o_mcp_param: Optional parameter provided by the MCP
  *                     response
- * @return int - 0 - operation
- * was successul.
+ *
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_cmd(struct qed_hwfn *p_hwfn,
 		struct qed_ptt *p_ptt,
@@ -417,37 +415,39 @@
 		u32 *o_mcp_param);
 
 /**
- * @brief - drains the nig, allowing completion to pass in case of pauses.
- *          (Should be called only from sleepable context)
+ * qed_mcp_drain(): drains the nig, allowing completion to pass in
+ *                  case of pauses.
+ *                  (Should be called only from sleepable context)
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ *
+ * Return: Int.
  */
 int qed_mcp_drain(struct qed_hwfn *p_hwfn,
 		  struct qed_ptt *p_ptt);
 
 /**
- * @brief Get the flash size value
+ * qed_mcp_get_flash_size(): Get the flash size value.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_flash_size  - flash size in bytes to be filled.
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ * @p_flash_size: Flash size in bytes to be filled.
  *
- * @return int - 0 - operation was successul.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_get_flash_size(struct qed_hwfn     *p_hwfn,
 			   struct qed_ptt       *p_ptt,
 			   u32 *p_flash_size);
 
 /**
- * @brief Send driver version to MFW
+ * qed_mcp_send_drv_version(): Send driver version to MFW.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param version - Version value
- * @param name - Protocol driver name
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ * @p_ver: Version value.
  *
- * @return int - 0 - operation was successul.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_send_drv_version(struct qed_hwfn *p_hwfn,
@@ -455,146 +455,148 @@
 			 struct qed_mcp_drv_version *p_ver);
 
 /**
- * @brief Read the MFW process kill counter
+ * qed_get_process_kill_counter(): Read the MFW process kill counter.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
  *
- * @return u32
+ * Return: u32.
  */
 u32 qed_get_process_kill_counter(struct qed_hwfn *p_hwfn,
 				 struct qed_ptt *p_ptt);
 
 /**
- * @brief Trigger a recovery process
+ * qed_start_recovery_process(): Trigger a recovery process.
  *
- *  @param p_hwfn
- *  @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
  *
- * @return int
+ * Return: Int.
  */
 int qed_start_recovery_process(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief A recovery handler must call this function as its first step.
- *        It is assumed that the handler is not run from an interrupt context.
+ * qed_recovery_prolog(): A recovery handler must call this function
+ *                        as its first step.
+ *                        It is assumed that the handler is not run from
+ *                        an interrupt context.
  *
- *  @param cdev
- *  @param p_ptt
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: int.
  */
 int qed_recovery_prolog(struct qed_dev *cdev);
 
 /**
- * @brief Notify MFW about the change in base device properties
+ * qed_mcp_ov_update_current_config(): Notify MFW about the change in base
+ *                                    device properties
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param client - qed client type
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @client: Qed client type.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ov_update_current_config(struct qed_hwfn *p_hwfn,
 				     struct qed_ptt *p_ptt,
 				     enum qed_ov_client client);
 
 /**
- * @brief Notify MFW about the driver state
+ * qed_mcp_ov_update_driver_state(): Notify MFW about the driver state.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param drv_state - Driver state
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @drv_state: Driver state.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ov_update_driver_state(struct qed_hwfn *p_hwfn,
 				   struct qed_ptt *p_ptt,
 				   enum qed_ov_driver_state drv_state);
 
 /**
- * @brief Send MTU size to MFW
+ * qed_mcp_ov_update_mtu(): Send MTU size to MFW.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param mtu - MTU size
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @mtu: MTU size.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ov_update_mtu(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt, u16 mtu);
 
 /**
- * @brief Send MAC address to MFW
+ * qed_mcp_ov_update_mac(): Send MAC address to MFW.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param mac - MAC address
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @mac: MAC address.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ov_update_mac(struct qed_hwfn *p_hwfn,
-			  struct qed_ptt *p_ptt, u8 *mac);
+			  struct qed_ptt *p_ptt, const u8 *mac);
 
 /**
- * @brief Send WOL mode to MFW
+ * qed_mcp_ov_update_wol(): Send WOL mode to MFW.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param wol - WOL mode
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @wol: WOL mode.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ov_update_wol(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt,
 			  enum qed_ov_wol wol);
 
 /**
- * @brief Set LED status
+ * qed_mcp_set_led(): Set LED status.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param mode - LED mode
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @mode: LED mode.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_set_led(struct qed_hwfn *p_hwfn,
 		    struct qed_ptt *p_ptt,
 		    enum qed_led_mode mode);
 
 /**
- * @brief Read from nvm
+ * qed_mcp_nvm_read(): Read from NVM.
  *
- *  @param cdev
- *  @param addr - nvm offset
- *  @param p_buf - nvm read buffer
- *  @param len - buffer len
+ * @cdev: Qed dev pointer.
+ * @addr: NVM offset.
+ * @p_buf: NVM read buffer.
+ * @len: Buffer len.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_nvm_read(struct qed_dev *cdev, u32 addr, u8 *p_buf, u32 len);
 
 /**
- * @brief Write to nvm
+ * qed_mcp_nvm_write(): Write to NVM.
  *
- *  @param cdev
- *  @param addr - nvm offset
- *  @param cmd - nvm command
- *  @param p_buf - nvm write buffer
- *  @param len - buffer len
+ * @cdev: Qed dev pointer.
+ * @addr: NVM offset.
+ * @cmd: NVM command.
+ * @p_buf: NVM write buffer.
+ * @len: Buffer len.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_nvm_write(struct qed_dev *cdev,
 		      u32 cmd, u32 addr, u8 *p_buf, u32 len);
 
 /**
- * @brief Check latest response
+ * qed_mcp_nvm_resp(): Check latest response.
  *
- *  @param cdev
- *  @param p_buf - nvm write buffer
+ * @cdev: Qed dev pointer.
+ * @p_buf: NVM write buffer.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_nvm_resp(struct qed_dev *cdev, u8 *p_buf);
 
@@ -604,13 +606,13 @@
 };
 
 /**
- * @brief Allows reading a whole nvram image
+ * qed_mcp_get_nvm_image_att(): Allows reading a whole nvram image.
  *
- * @param p_hwfn
- * @param image_id - image to get attributes for
- * @param p_image_att - image attributes structure into which to fill data
+ * @p_hwfn: HW device data.
+ * @image_id: Image to get attributes for.
+ * @p_image_att: Image attributes structure into which to fill data.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_get_nvm_image_att(struct qed_hwfn *p_hwfn,
@@ -618,64 +620,65 @@
 			  struct qed_nvm_image_att *p_image_att);
 
 /**
- * @brief Allows reading a whole nvram image
+ * qed_mcp_get_nvm_image(): Allows reading a whole nvram image.
  *
- * @param p_hwfn
- * @param image_id - image requested for reading
- * @param p_buffer - allocated buffer into which to fill data
- * @param buffer_len - length of the allocated buffer.
+ * @p_hwfn: HW device data.
+ * @image_id: image requested for reading.
+ * @p_buffer: allocated buffer into which to fill data.
+ * @buffer_len: length of the allocated buffer.
  *
- * @return 0 iff p_buffer now contains the nvram image.
+ * Return: 0 if p_buffer now contains the nvram image.
  */
 int qed_mcp_get_nvm_image(struct qed_hwfn *p_hwfn,
 			  enum qed_nvm_images image_id,
 			  u8 *p_buffer, u32 buffer_len);
 
 /**
- * @brief Bist register test
+ * qed_mcp_bist_register_test(): Bist register test.
  *
- *  @param p_hwfn    - hw function
- *  @param p_ptt     - PTT required for register access
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_bist_register_test(struct qed_hwfn *p_hwfn,
 			       struct qed_ptt *p_ptt);
 
 /**
- * @brief Bist clock test
+ * qed_mcp_bist_clock_test(): Bist clock test.
  *
- *  @param p_hwfn    - hw function
- *  @param p_ptt     - PTT required for register access
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_bist_clock_test(struct qed_hwfn *p_hwfn,
 			    struct qed_ptt *p_ptt);
 
 /**
- * @brief Bist nvm test - get number of images
+ * qed_mcp_bist_nvm_get_num_images(): Bist nvm test - get number of images.
  *
- *  @param p_hwfn       - hw function
- *  @param p_ptt        - PTT required for register access
- *  @param num_images   - number of images if operation was
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ * @num_images: number of images if operation was
  *			  successful. 0 if not.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_bist_nvm_get_num_images(struct qed_hwfn *p_hwfn,
 				    struct qed_ptt *p_ptt,
 				    u32 *num_images);
 
 /**
- * @brief Bist nvm test - get image attributes by index
+ * qed_mcp_bist_nvm_get_image_att(): Bist nvm test - get image attributes
+ *                                   by index.
  *
- *  @param p_hwfn      - hw function
- *  @param p_ptt       - PTT required for register access
- *  @param p_image_att - Attributes of image
- *  @param image_index - Index of image to get information for
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ * @p_image_att: Attributes of image.
+ * @image_index: Index of image to get information for.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_bist_nvm_get_image_att(struct qed_hwfn *p_hwfn,
 				   struct qed_ptt *p_ptt,
@@ -683,23 +686,26 @@
 				   u32 image_index);
 
 /**
- * @brief - Processes the TLV request from MFW i.e., get the required TLV info
- *          from the qed client and send it to the MFW.
+ * qed_mfw_process_tlv_req(): Processes the TLV request from MFW i.e.,
+ *                            get the required TLV info
+ *                            from the qed client and send it to the MFW.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param return 0 upon success.
+ * Return: 0 upon success.
  */
 int qed_mfw_process_tlv_req(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Send raw debug data to the MFW
+ * qed_mcp_send_raw_debug_data(): Send raw debug data to the MFW
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_buf: raw debug data buffer.
+ * @size: Buffer size.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_buf - raw debug data buffer
- * @param size - buffer size
+ * Return : Int.
  */
 int
 qed_mcp_send_raw_debug_data(struct qed_hwfn *p_hwfn,
@@ -796,47 +802,49 @@
 }
 
 /**
- * @brief Initialize the interface with the MCP
+ * qed_mcp_cmd_init(): Initialize the interface with the MCP.
  *
- * @param p_hwfn - HW func
- * @param p_ptt - PTT required for register access
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
  *
- * @return int
+ * Return: Int.
  */
 int qed_mcp_cmd_init(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt);
 
 /**
- * @brief Initialize the port interface with the MCP
+ * qed_mcp_cmd_port_init(): Initialize the port interface with the MCP
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Void.
  *
- * @param p_hwfn
- * @param p_ptt
  * Can only be called after `num_ports_in_engines' is set
  */
 void qed_mcp_cmd_port_init(struct qed_hwfn *p_hwfn,
 			   struct qed_ptt *p_ptt);
 /**
- * @brief Releases resources allocated during the init process.
+ * qed_mcp_free(): Releases resources allocated during the init process.
  *
- * @param p_hwfn - HW func
- * @param p_ptt - PTT required for register access
+ * @p_hwfn: HW function.
  *
- * @return int
+ * Return: Int.
  */
 
 int qed_mcp_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief This function is called from the DPC context. After
- * pointing PTT to the mfw mb, check for events sent by the MCP
- * to the driver and ack them. In case a critical event
- * detected, it will be handled here, otherwise the work will be
- * queued to a sleepable work-queue.
- *
- * @param p_hwfn - HW function
- * @param p_ptt - PTT required for register access
- * @return int - 0 - operation
- * was successul.
+ * qed_mcp_handle_events(): This function is called from the DPC context.
+ *           After pointing PTT to the mfw mb, check for events sent by
+ *           the MCP to the driver and ack them. In case a critical event
+ *           detected, it will be handled here, otherwise the work will be
+ *            queued to a sleepable work-queue.
+ *
+ * @p_hwfn: HW function.
+ * @p_ptt: PTT required for register access.
+ *
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_handle_events(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt);
@@ -858,106 +866,111 @@
 };
 
 /**
- * @brief Sends a LOAD_REQ to the MFW, and in case the operation succeeds,
- *        returns whether this PF is the first on the engine/port or function.
+ * qed_mcp_load_req(): Sends a LOAD_REQ to the MFW, and in case the
+ *                     operation succeeds, returns whether this PF is
+ *                     the first on the engine/port or function.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_params
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_params: Params.
  *
- * @return int - 0 - Operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_load_req(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt,
 		     struct qed_load_req_params *p_params);
 
 /**
- * @brief Sends a LOAD_DONE message to the MFW
+ * qed_mcp_load_done(): Sends a LOAD_DONE message to the MFW.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int - 0 - Operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_load_done(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Sends a UNLOAD_REQ message to the MFW
+ * qed_mcp_unload_req(): Sends a UNLOAD_REQ message to the MFW.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int - 0 - Operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_unload_req(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Sends a UNLOAD_DONE message to the MFW
+ * qed_mcp_unload_done(): Sends a UNLOAD_DONE message to the MFW
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int - 0 - Operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_unload_done(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Read the MFW mailbox into Current buffer.
+ * qed_mcp_read_mb(): Read the MFW mailbox into Current buffer.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Void.
  */
 void qed_mcp_read_mb(struct qed_hwfn *p_hwfn,
 		     struct qed_ptt *p_ptt);
 
 /**
- * @brief Ack to mfw that driver finished FLR process for VFs
+ * qed_mcp_ack_vf_flr(): Ack to mfw that driver finished FLR process for VFs
  *
- * @param p_hwfn
- * @param p_ptt
- * @param vfs_to_ack - bit mask of all engine VFs for which the PF acks.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @vfs_to_ack: bit mask of all engine VFs for which the PF acks.
  *
- * @param return int - 0 upon success.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ack_vf_flr(struct qed_hwfn *p_hwfn,
 		       struct qed_ptt *p_ptt, u32 *vfs_to_ack);
 
 /**
- * @brief - calls during init to read shmem of all function-related info.
+ * qed_mcp_fill_shmem_func_info(): Calls during init to read shmem of
+ *                                 all function-related info.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param return 0 upon success.
+ * Return: 0 upon success.
  */
 int qed_mcp_fill_shmem_func_info(struct qed_hwfn *p_hwfn,
 				 struct qed_ptt *p_ptt);
 
 /**
- * @brief - Reset the MCP using mailbox command.
+ * qed_mcp_reset(): Reset the MCP using mailbox command.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param return 0 upon success.
+ * Return: 0 upon success.
  */
 int qed_mcp_reset(struct qed_hwfn *p_hwfn,
 		  struct qed_ptt *p_ptt);
 
 /**
- * @brief - Sends an NVM read command request to the MFW to get
- *        a buffer.
+ * qed_mcp_nvm_rd_cmd(): Sends an NVM read command request to the MFW to get
+ *                       a buffer.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param cmd - Command: DRV_MSG_CODE_NVM_GET_FILE_DATA or
- *            DRV_MSG_CODE_NVM_READ_NVRAM commands
- * @param param - [0:23] - Offset [24:31] - Size
- * @param o_mcp_resp - MCP response
- * @param o_mcp_param - MCP response param
- * @param o_txn_size -  Buffer size output
- * @param o_buf - Pointer to the buffer returned by the MFW.
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @cmd: (Command) DRV_MSG_CODE_NVM_GET_FILE_DATA or
+ *            DRV_MSG_CODE_NVM_READ_NVRAM commands.
+ * @param: [0:23] - Offset [24:31] - Size.
+ * @o_mcp_resp: MCP response.
+ * @o_mcp_param: MCP response param.
+ * @o_txn_size: Buffer size output.
+ * @o_buf: Pointer to the buffer returned by the MFW.
  *
- * @param return 0 upon success.
+ * Return: 0 upon success.
  */
 int qed_mcp_nvm_rd_cmd(struct qed_hwfn *p_hwfn,
 		       struct qed_ptt *p_ptt,
@@ -967,60 +980,61 @@
 		       u32 *o_mcp_param, u32 *o_txn_size, u32 *o_buf);
 
 /**
- * @brief Read from sfp
+ * qed_mcp_phy_sfp_read(): Read from sfp.
  *
- *  @param p_hwfn - hw function
- *  @param p_ptt  - PTT required for register access
- *  @param port   - transceiver port
- *  @param addr   - I2C address
- *  @param offset - offset in sfp
- *  @param len    - buffer length
- *  @param p_buf  - buffer to read into
+ * @p_hwfn: HW device data.
+ * @p_ptt: PTT required for register access.
+ * @port: transceiver port.
+ * @addr: I2C address.
+ * @offset: offset in sfp.
+ * @len: buffer length.
+ * @p_buf: buffer to read into.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_phy_sfp_read(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt,
 			 u32 port, u32 addr, u32 offset, u32 len, u8 *p_buf);
 
 /**
- * @brief indicates whether the MFW objects [under mcp_info] are accessible
+ * qed_mcp_is_init(): indicates whether the MFW objects [under mcp_info]
+ *                    are accessible
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return true iff MFW is running and mcp_info is initialized
+ * Return: true if MFW is running and mcp_info is initialized.
  */
 bool qed_mcp_is_init(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief request MFW to configure MSI-X for a VF
+ * qed_mcp_config_vf_msix(): Request MFW to configure MSI-X for a VF.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param vf_id - absolute inside engine
- * @param num_sbs - number of entries to request
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @vf_id: absolute inside engine.
+ * @num: number of entries to request.
  *
- * @return int
+ * Return: Int.
  */
 int qed_mcp_config_vf_msix(struct qed_hwfn *p_hwfn,
 			   struct qed_ptt *p_ptt, u8 vf_id, u8 num);
 
 /**
- * @brief - Halt the MCP.
+ * qed_mcp_halt(): Halt the MCP.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param return 0 upon success.
+ * Return: 0 upon success.
  */
 int qed_mcp_halt(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief - Wake up the MCP.
+ * qed_mcp_resume: Wake up the MCP.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param return 0 upon success.
+ * Return: 0 upon success.
  */
 int qed_mcp_resume(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
@@ -1038,13 +1052,13 @@
 int qed_mcp_mask_parities(struct qed_hwfn *p_hwfn,
 			  struct qed_ptt *p_ptt, u32 mask_parities);
 
-/* @brief - Gets the mdump retained data from the MFW.
+/* qed_mcp_mdump_get_retain(): Gets the mdump retained data from the MFW.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_mdump_retain
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_mdump_retain: mdump retain.
  *
- * @param return 0 upon success.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_mdump_get_retain(struct qed_hwfn *p_hwfn,
@@ -1052,15 +1066,15 @@
 			 struct mdump_retain_data_stc *p_mdump_retain);
 
 /**
- * @brief - Sets the MFW's max value for the given resource
+ * qed_mcp_set_resc_max_val(): Sets the MFW's max value for the given resource.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param res_id
- *  @param resc_max_val
- *  @param p_mcp_resp
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @res_id: RES ID.
+ * @resc_max_val: Resec max val.
+ * @p_mcp_resp: MCP Resp
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_set_resc_max_val(struct qed_hwfn *p_hwfn,
@@ -1069,16 +1083,17 @@
 			 u32 resc_max_val, u32 *p_mcp_resp);
 
 /**
- * @brief - Gets the MFW allocation info for the given resource
+ * qed_mcp_get_resc_info(): Gets the MFW allocation info for the given
+ *                          resource.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param res_id
- *  @param p_mcp_resp
- *  @param p_resc_num
- *  @param p_resc_start
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @res_id: Res ID.
+ * @p_mcp_resp: MCP resp.
+ * @p_resc_num: Resc num.
+ * @p_resc_start: Resc start.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_get_resc_info(struct qed_hwfn *p_hwfn,
@@ -1087,13 +1102,13 @@
 		      u32 *p_mcp_resp, u32 *p_resc_num, u32 *p_resc_start);
 
 /**
- * @brief Send eswitch mode to MFW
+ * qed_mcp_ov_update_eswitch(): Send eswitch mode to MFW.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param eswitch - eswitch mode
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @eswitch: eswitch mode.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_ov_update_eswitch(struct qed_hwfn *p_hwfn,
 			      struct qed_ptt *p_ptt,
@@ -1113,12 +1128,12 @@
 };
 
 /**
- * @brief - Initiates PF FLR
+ * qed_mcp_initiate_pf_flr(): Initiates PF FLR.
  *
- *  @param p_hwfn
- *  @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int qed_mcp_initiate_pf_flr(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 struct qed_resc_lock_params {
@@ -1151,13 +1166,13 @@
 };
 
 /**
- * @brief Acquires MFW generic resource lock
+ * qed_mcp_resc_lock(): Acquires MFW generic resource lock.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param p_params
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_params: Params.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_resc_lock(struct qed_hwfn *p_hwfn,
@@ -1175,13 +1190,13 @@
 };
 
 /**
- * @brief Releases MFW generic resource lock
+ * qed_mcp_resc_unlock(): Releases MFW generic resource lock.
  *
- *  @param p_hwfn
- *  @param p_ptt
- *  @param p_params
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_params: Params.
  *
- * @return int - 0 - operation was successful.
+ * Return: Int - 0 - Operation was successul.
  */
 int
 qed_mcp_resc_unlock(struct qed_hwfn *p_hwfn,
@@ -1189,12 +1204,15 @@
 		    struct qed_resc_unlock_params *p_params);
 
 /**
- * @brief - default initialization for lock/unlock resource structs
+ * qed_mcp_resc_lock_default_init(): Default initialization for
+ *                                   lock/unlock resource structs.
+ *
+ * @p_lock: lock params struct to be initialized; Can be NULL.
+ * @p_unlock: unlock params struct to be initialized; Can be NULL.
+ * @resource: the requested resource.
+ * @b_is_permanent: disable retries & aging when set.
  *
- * @param p_lock - lock params struct to be initialized; Can be NULL
- * @param p_unlock - unlock params struct to be initialized; Can be NULL
- * @param resource - the requested resource
- * @paral b_is_permanent - disable retries & aging when set
+ * Return: Void.
  */
 void qed_mcp_resc_lock_default_init(struct qed_resc_lock_params *p_lock,
 				    struct qed_resc_unlock_params *p_unlock,
@@ -1202,94 +1220,117 @@
 				    resource, bool b_is_permanent);
 
 /**
- * @brief - Return whether management firmware support smart AN
+ * qed_mcp_is_smart_an_supported(): Return whether management firmware
+ *                                  support smart AN
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return bool - true if feature is supported.
+ * Return: bool true if feature is supported.
  */
 bool qed_mcp_is_smart_an_supported(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief Learn of supported MFW features; To be done during early init
+ * qed_mcp_get_capabilities(): Learn of supported MFW features;
+ *                             To be done during early init.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Int.
  */
 int qed_mcp_get_capabilities(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Inform MFW of set of features supported by driver. Should be done
- * inside the content of the LOAD_REQ.
+ * qed_mcp_set_capabilities(): Inform MFW of set of features supported
+ *                             by driver. Should be done inside the content
+ *                             of the LOAD_REQ.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Int.
  */
 int qed_mcp_set_capabilities(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Read ufp config from the shared memory.
+ * qed_mcp_read_ufp_config(): Read ufp config from the shared memory.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param p_hwfn
- * @param p_ptt
+ * Return: Void.
  */
 void qed_mcp_read_ufp_config(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Populate the nvm info shadow in the given hardware function
+ * qed_mcp_nvm_info_populate(): Populate the nvm info shadow in the given
+ *                              hardware function.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Int.
  */
 int qed_mcp_nvm_info_populate(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief Delete nvm info shadow in the given hardware function
+ * qed_mcp_nvm_info_free(): Delete nvm info shadow in the given
+ *                          hardware function.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_mcp_nvm_info_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief Get the engine affinity configuration.
+ * qed_mcp_get_engine_config(): Get the engine affinity configuration.
  *
- * @param p_hwfn
- * @param p_ptt
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ *
+ * Return: Int.
  */
 int qed_mcp_get_engine_config(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Get the PPFID bitmap.
+ * qed_mcp_get_ppfid_bitmap(): Get the PPFID bitmap.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
  *
- * @param p_hwfn
- * @param p_ptt
+ * Return: Int.
  */
 int qed_mcp_get_ppfid_bitmap(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt);
 
 /**
- * @brief Get NVM config attribute value.
+ * qed_mcp_nvm_get_cfg(): Get NVM config attribute value.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @option_id: Option ID.
+ * @entity_id: Entity ID.
+ * @flags: Flags.
+ * @p_buf: Buf.
+ * @p_len: Len.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param option_id
- * @param entity_id
- * @param flags
- * @param p_buf
- * @param p_len
+ * Return: Int.
  */
 int qed_mcp_nvm_get_cfg(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt,
 			u16 option_id, u8 entity_id, u16 flags, u8 *p_buf,
 			u32 *p_len);
 
 /**
- * @brief Set NVM config attribute value.
+ * qed_mcp_nvm_set_cfg(): Set NVM config attribute value.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @option_id: Option ID.
+ * @entity_id: Entity ID.
+ * @flags: Flags.
+ * @p_buf: Buf.
+ * @len: Len.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param option_id
- * @param entity_id
- * @param flags
- * @param p_buf
- * @param len
+ * Return: Int.
  */
 int qed_mcp_nvm_set_cfg(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt,
 			u16 option_id, u8 entity_id, u16 flags, u8 *p_buf,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_mng_tlv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_mng_tlv.c
@@ -422,7 +422,7 @@
 	if (p_time->hour > 23)
 		p_time->hour = 0;
 	if (p_time->min > 59)
-		p_time->hour = 0;
+		p_time->min = 0;
 	if (p_time->msec > 999)
 		p_time->msec = 0;
 	if (p_time->usec > 999)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_rdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_rdma.c
@@ -1966,7 +1966,7 @@
 
 static int qed_roce_ll2_set_mac_filter(struct qed_dev *cdev,
 				       u8 *old_mac_address,
-				       u8 *new_mac_address)
+				       const u8 *new_mac_address)
 {
 	int rc = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_selftest.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_selftest.h
@@ -6,47 +6,47 @@
 #include <linux/types.h>
 
 /**
- * @brief qed_selftest_memory - Perform memory test
+ * qed_selftest_memory(): Perform memory test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_selftest_memory(struct qed_dev *cdev);
 
 /**
- * @brief qed_selftest_interrupt - Perform interrupt test
+ * qed_selftest_interrupt(): Perform interrupt test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_selftest_interrupt(struct qed_dev *cdev);
 
 /**
- * @brief qed_selftest_register - Perform register test
+ * qed_selftest_register(): Perform register test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_selftest_register(struct qed_dev *cdev);
 
 /**
- * @brief qed_selftest_clock - Perform clock test
+ * qed_selftest_clock(): Perform clock test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_selftest_clock(struct qed_dev *cdev);
 
 /**
- * @brief qed_selftest_nvram - Perform nvram test
+ * qed_selftest_nvram(): Perform nvram test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return int
+ * Return: Int.
  */
 int qed_selftest_nvram(struct qed_dev *cdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_sp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_sp.h
@@ -31,23 +31,18 @@
 };
 
 /**
- * @brief qed_eth_cqe_completion - handles the completion of a
- *        ramrod on the cqe ring
+ * qed_eth_cqe_completion(): handles the completion of a
+ *                           ramrod on the cqe ring.
  *
- * @param p_hwfn
- * @param cqe
+ * @p_hwfn: HW device data.
+ * @cqe: CQE.
  *
- * @return int
+ * Return: Int.
  */
 int qed_eth_cqe_completion(struct qed_hwfn *p_hwfn,
 			   struct eth_slow_path_rx_cqe *cqe);
 
-/**
- *  @file
- *
- *  QED Slow-hwfn queue interface
- */
-
+ /*  QED Slow-hwfn queue interface */
 union ramrod_data {
 	struct pf_start_ramrod_data pf_start;
 	struct pf_update_ramrod_data pf_update;
@@ -207,117 +202,128 @@
 };
 
 /**
- * @brief qed_spq_post - Posts a Slow hwfn request to FW, or lacking that
- *        Pends it to the future list.
+ * qed_spq_post(): Posts a Slow hwfn request to FW, or lacking that
+ *                 Pends it to the future list.
  *
- * @param p_hwfn
- * @param p_req
+ * @p_hwfn: HW device data.
+ * @p_ent: Ent.
+ * @fw_return_code: Return code from firmware.
  *
- * @return int
+ * Return: Int.
  */
 int qed_spq_post(struct qed_hwfn *p_hwfn,
 		 struct qed_spq_entry *p_ent,
 		 u8 *fw_return_code);
 
 /**
- * @brief qed_spq_allocate - Alloocates & initializes the SPQ and EQ.
+ * qed_spq_alloc(): Alloocates & initializes the SPQ and EQ.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_spq_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_spq_setup - Reset the SPQ to its start state.
+ * qed_spq_setup(): Reset the SPQ to its start state.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_spq_setup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_spq_deallocate - Deallocates the given SPQ struct.
+ * qed_spq_free(): Deallocates the given SPQ struct.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_spq_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_spq_get_entry - Obtain an entrry from the spq
- *        free pool list.
- *
- *
+ * qed_spq_get_entry(): Obtain an entrry from the spq
+ *                      free pool list.
  *
- * @param p_hwfn
- * @param pp_ent
+ * @p_hwfn: HW device data.
+ * @pp_ent: PP ENT.
  *
- * @return int
+ * Return: Int.
  */
 int
 qed_spq_get_entry(struct qed_hwfn *p_hwfn,
 		  struct qed_spq_entry **pp_ent);
 
 /**
- * @brief qed_spq_return_entry - Return an entry to spq free
- *                                 pool list
+ * qed_spq_return_entry(): Return an entry to spq free pool list.
  *
- * @param p_hwfn
- * @param p_ent
+ * @p_hwfn: HW device data.
+ * @p_ent: P ENT.
+ *
+ * Return: Void.
  */
 void qed_spq_return_entry(struct qed_hwfn *p_hwfn,
 			  struct qed_spq_entry *p_ent);
 /**
- * @brief qed_eq_allocate - Allocates & initializes an EQ struct
+ * qed_eq_alloc(): Allocates & initializes an EQ struct.
  *
- * @param p_hwfn
- * @param num_elem number of elements in the eq
+ * @p_hwfn: HW device data.
+ * @num_elem: number of elements in the eq.
  *
- * @return int
+ * Return: Int.
  */
 int qed_eq_alloc(struct qed_hwfn *p_hwfn, u16 num_elem);
 
 /**
- * @brief qed_eq_setup - Reset the EQ to its start state.
+ * qed_eq_setup(): Reset the EQ to its start state.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_eq_setup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_eq_free - deallocates the given EQ struct.
+ * qed_eq_free(): deallocates the given EQ struct.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_eq_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_eq_prod_update - update the FW with default EQ producer
+ * qed_eq_prod_update(): update the FW with default EQ producer.
+ *
+ * @p_hwfn: HW device data.
+ * @prod: Prod.
  *
- * @param p_hwfn
- * @param prod
+ * Return: Void.
  */
 void qed_eq_prod_update(struct qed_hwfn *p_hwfn,
 			u16 prod);
 
 /**
- * @brief qed_eq_completion - Completes currently pending EQ elements
+ * qed_eq_completion(): Completes currently pending EQ elements.
  *
- * @param p_hwfn
- * @param cookie
+ * @p_hwfn: HW device data.
+ * @cookie: Cookie.
  *
- * @return int
+ * Return: Int.
  */
 int qed_eq_completion(struct qed_hwfn *p_hwfn,
 		      void *cookie);
 
 /**
- * @brief qed_spq_completion - Completes a single event
+ * qed_spq_completion(): Completes a single event.
  *
- * @param p_hwfn
- * @param echo - echo value from cookie (used for determining completion)
- * @param p_data - data from cookie (used in callback function if applicable)
+ * @p_hwfn: HW device data.
+ * @echo: echo value from cookie (used for determining completion).
+ * @fw_return_code: FW return code.
+ * @p_data: data from cookie (used in callback function if applicable).
  *
- * @return int
+ * Return: Int.
  */
 int qed_spq_completion(struct qed_hwfn *p_hwfn,
 		       __le16 echo,
@@ -325,44 +331,43 @@
 		       union event_ring_data *p_data);
 
 /**
- * @brief qed_spq_get_cid - Given p_hwfn, return cid for the hwfn's SPQ
+ * qed_spq_get_cid(): Given p_hwfn, return cid for the hwfn's SPQ.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return u32 - SPQ CID
+ * Return: u32 - SPQ CID.
  */
 u32 qed_spq_get_cid(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_consq_alloc - Allocates & initializes an ConsQ
- *        struct
+ * qed_consq_alloc(): Allocates & initializes an ConsQ struct.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_consq_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_consq_setup - Reset the ConsQ to its start state.
+ * qed_consq_setup(): Reset the ConsQ to its start state.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return Void.
  */
 void qed_consq_setup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_consq_free - deallocates the given ConsQ struct.
+ * qed_consq_free(): deallocates the given ConsQ struct.
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return Void.
  */
 void qed_consq_free(struct qed_hwfn *p_hwfn);
 int qed_spq_pend_post(struct qed_hwfn *p_hwfn);
 
-/**
- * @file
- *
- * @brief Slow-hwfn low-level commands (Ramrods) function definitions.
- */
+/* Slow-hwfn low-level commands (Ramrods) function definitions. */
 
 #define QED_SP_EQ_COMPLETION  0x01
 #define QED_SP_CQE_COMPLETION 0x02
@@ -377,12 +382,15 @@
 };
 
 /**
- * @brief Returns a SPQ entry to the pool / frees the entry if allocated.
- *        Should be called on in error flows after initializing the SPQ entry
- *        and before posting it.
+ * qed_sp_destroy_request(): Returns a SPQ entry to the pool / frees the
+ *                           entry if allocated. Should be called on in error
+ *                           flows after initializing the SPQ entry
+ *                           and before posting it.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ent: Ent.
  *
- * @param p_hwfn
- * @param p_ent
+ * Return: Void.
  */
 void qed_sp_destroy_request(struct qed_hwfn *p_hwfn,
 			    struct qed_spq_entry *p_ent);
@@ -394,7 +402,14 @@
 			struct qed_sp_init_data *p_data);
 
 /**
- * @brief qed_sp_pf_start - PF Function Start Ramrod
+ * qed_sp_pf_start(): PF Function Start Ramrod.
+ *
+ * @p_hwfn: HW device data.
+ * @p_ptt: P_ptt.
+ * @p_tunn: P_tunn.
+ * @allow_npar_tx_switch: Allow NPAR TX Switch.
+ *
+ * Return: Int.
  *
  * This ramrod is sent to initialize a physical function (PF). It will
  * configure the function related parameters and write its completion to the
@@ -404,12 +419,6 @@
  * allocated by the driver on host memory and its parameters are written
  * to the internal RAM of the UStorm by the Function Start Ramrod.
  *
- * @param p_hwfn
- * @param p_ptt
- * @param p_tunn
- * @param allow_npar_tx_switch
- *
- * @return int
  */
 
 int qed_sp_pf_start(struct qed_hwfn *p_hwfn,
@@ -418,47 +427,33 @@
 		    bool allow_npar_tx_switch);
 
 /**
- * @brief qed_sp_pf_update - PF Function Update Ramrod
+ * qed_sp_pf_update(): PF Function Update Ramrod.
  *
- * This ramrod updates function-related parameters. Every parameter can be
- * updated independently, according to configuration flags.
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Int.
  *
- * @return int
+ * This ramrod updates function-related parameters. Every parameter can be
+ * updated independently, according to configuration flags.
  */
 
 int qed_sp_pf_update(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_sp_pf_update_stag - Update firmware of new outer tag
+ * qed_sp_pf_update_stag(): Update firmware of new outer tag.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_sp_pf_update_stag(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_sp_pf_stop - PF Function Stop Ramrod
- *
- * This ramrod is sent to close a Physical Function (PF). It is the last ramrod
- * sent and the last completion written to the PFs Event Ring. This ramrod also
- * deletes the context for the Slowhwfn connection on this PF.
- *
- * @note Not required for first packet.
- *
- * @param p_hwfn
- *
- * @return int
- */
-
-/**
- * @brief qed_sp_pf_update_ufp - PF ufp update Ramrod
+ * qed_sp_pf_update_ufp(): PF ufp update Ramrod.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_sp_pf_update_ufp(struct qed_hwfn *p_hwfn);
 
@@ -470,11 +465,11 @@
 			      enum spq_mode comp_mode,
 			      struct qed_spq_comp_cb *p_comp_data);
 /**
- * @brief qed_sp_heartbeat_ramrod - Send empty Ramrod
+ * qed_sp_heartbeat_ramrod(): Send empty Ramrod.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 
 int qed_sp_heartbeat_ramrod(struct qed_hwfn *p_hwfn);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_sriov.c
@@ -2982,12 +2982,16 @@
 	u8 mask = QED_ACCEPT_UCAST_UNMATCHED | QED_ACCEPT_MCAST_UNMATCHED;
 	struct qed_filter_accept_flags *flags = &params->accept_flags;
 	struct qed_public_vf_info *vf_info;
+	u16 tlv_mask;
+
+	tlv_mask = BIT(QED_IOV_VP_UPDATE_ACCEPT_PARAM) |
+		   BIT(QED_IOV_VP_UPDATE_ACCEPT_ANY_VLAN);
 
 	/* Untrusted VFs can't even be trusted to know that fact.
 	 * Simply indicate everything is configured fine, and trace
 	 * configuration 'behind their back'.
 	 */
-	if (!(*tlvs & BIT(QED_IOV_VP_UPDATE_ACCEPT_PARAM)))
+	if (!(*tlvs & tlv_mask))
 		return 0;
 
 	vf_info = qed_iov_get_public_vf_info(hwfn, vfid, true);
@@ -3004,6 +3008,13 @@
 			flags->tx_accept_filter &= ~mask;
 	}
 
+	if (params->update_accept_any_vlan_flg) {
+		vf_info->accept_any_vlan = params->accept_any_vlan;
+
+		if (vf_info->forced_vlan && !vf_info->is_trusted_configured)
+			params->accept_any_vlan = false;
+	}
+
 	return 0;
 }
 
@@ -3778,11 +3789,11 @@
 	return found;
 }
 
-static void qed_iov_get_link(struct qed_hwfn *p_hwfn,
-			     u16 vfid,
-			     struct qed_mcp_link_params *p_params,
-			     struct qed_mcp_link_state *p_link,
-			     struct qed_mcp_link_capabilities *p_caps)
+static int qed_iov_get_link(struct qed_hwfn *p_hwfn,
+			    u16 vfid,
+			    struct qed_mcp_link_params *p_params,
+			    struct qed_mcp_link_state *p_link,
+			    struct qed_mcp_link_capabilities *p_caps)
 {
 	struct qed_vf_info *p_vf = qed_iov_get_vf_info(p_hwfn,
 						       vfid,
@@ -3790,7 +3801,7 @@
 	struct qed_bulletin_content *p_bulletin;
 
 	if (!p_vf)
-		return;
+		return -EINVAL;
 
 	p_bulletin = p_vf->bulletin.p_virt;
 
@@ -3800,6 +3811,7 @@
 		__qed_vf_get_link_state(p_hwfn, p_link, p_bulletin);
 	if (p_caps)
 		__qed_vf_get_link_caps(p_hwfn, p_caps, p_bulletin);
+	return 0;
 }
 
 static int
@@ -4366,6 +4378,9 @@
 	}
 
 	vf = qed_iov_get_vf_info(QED_LEADING_HWFN(cdev), (u16)vfid, true);
+	if (!vf)
+		return -EINVAL;
+
 	vport_id = vf->vport_id;
 
 	return qed_configure_vport_wfq(cdev, vport_id, rate);
@@ -4658,6 +4673,7 @@
 	struct qed_public_vf_info *vf_info;
 	struct qed_mcp_link_state link;
 	u32 tx_rate;
+	int ret;
 
 	/* Sanitize request */
 	if (IS_VF(cdev))
@@ -4671,7 +4687,9 @@
 
 	vf_info = qed_iov_get_public_vf_info(hwfn, vf_id, true);
 
-	qed_iov_get_link(hwfn, vf_id, NULL, &link, NULL);
+	ret = qed_iov_get_link(hwfn, vf_id, NULL, &link, NULL);
+	if (ret)
+		return ret;
 
 	/* Fill information about VF */
 	ivi->vf = vf_id;
@@ -4687,6 +4705,7 @@
 	tx_rate = vf_info->tx_rate;
 	ivi->max_tx_rate = tx_rate ? tx_rate : link.speed;
 	ivi->min_tx_rate = qed_iov_get_vf_min_rate(hwfn, vf_id);
+	ivi->trusted = vf_info->is_trusted_request;
 
 	return 0;
 }
@@ -5108,7 +5127,7 @@
 
 		/* Validate that the VF has a configured vport */
 		vf = qed_iov_get_vf_info(hwfn, i, true);
-		if (!vf->vport_instance)
+		if (!vf || !vf->vport_instance)
 			continue;
 
 		memset(&params, 0, sizeof(params));
@@ -5117,6 +5136,12 @@
 
 		params.update_ctl_frame_check = 1;
 		params.mac_chk_en = !vf_info->is_trusted_configured;
+		params.update_accept_any_vlan_flg = 0;
+
+		if (vf_info->accept_any_vlan && vf_info->forced_vlan) {
+			params.update_accept_any_vlan_flg = 1;
+			params.accept_any_vlan = vf_info->accept_any_vlan;
+		}
 
 		if (vf_info->rx_accept_mode & mask) {
 			flags->update_rx_mode_config = 1;
@@ -5132,13 +5157,20 @@
 		if (!vf_info->is_trusted_configured) {
 			flags->rx_accept_filter &= ~mask;
 			flags->tx_accept_filter &= ~mask;
+			params.accept_any_vlan = false;
 		}
 
 		if (flags->update_rx_mode_config ||
 		    flags->update_tx_mode_config ||
-		    params.update_ctl_frame_check)
+		    params.update_ctl_frame_check ||
+		    params.update_accept_any_vlan_flg) {
+			DP_VERBOSE(hwfn, QED_MSG_IOV,
+				   "vport update config for %s VF[abs 0x%x rel 0x%x]\n",
+				   vf_info->is_trusted_configured ? "trusted" : "untrusted",
+				   vf->abs_vf_id, vf->relative_vf_id);
 			qed_sp_vport_update(hwfn, &params,
 					    QED_SPQ_MODE_EBLOCK, NULL);
+		}
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_sriov.h
@@ -62,6 +62,7 @@
 	bool is_trusted_request;
 	u8 rx_accept_mode;
 	u8 tx_accept_mode;
+	bool accept_any_vlan;
 };
 
 struct qed_iov_vf_init_params {
@@ -250,29 +251,31 @@
 
 #ifdef CONFIG_QED_SRIOV
 /**
- * @brief Check if given VF ID @vfid is valid
- *        w.r.t. @b_enabled_only value
- *        if b_enabled_only = true - only enabled VF id is valid
- *        else any VF id less than max_vfs is valid
- *
- * @param p_hwfn
- * @param rel_vf_id - Relative VF ID
- * @param b_enabled_only - consider only enabled VF
- * @param b_non_malicious - true iff we want to validate vf isn't malicious.
+ * qed_iov_is_valid_vfid(): Check if given VF ID @vfid is valid
+ *                          w.r.t. @b_enabled_only value
+ *                          if b_enabled_only = true - only enabled
+ *                          VF id is valid.
+ *                          else any VF id less than max_vfs is valid.
+ *
+ * @p_hwfn: HW device data.
+ * @rel_vf_id: Relative VF ID.
+ * @b_enabled_only: consider only enabled VF.
+ * @b_non_malicious: true iff we want to validate vf isn't malicious.
  *
- * @return bool - true for valid VF ID
+ * Return: bool - true for valid VF ID
  */
 bool qed_iov_is_valid_vfid(struct qed_hwfn *p_hwfn,
 			   int rel_vf_id,
 			   bool b_enabled_only, bool b_non_malicious);
 
 /**
- * @brief - Given a VF index, return index of next [including that] active VF.
+ * qed_iov_get_next_active_vf(): Given a VF index, return index of
+ *                               next [including that] active VF.
  *
- * @param p_hwfn
- * @param rel_vf_id
+ * @p_hwfn: HW device data.
+ * @rel_vf_id: VF ID.
  *
- * @return MAX_NUM_VFS in case no further active VFs, otherwise index.
+ * Return: MAX_NUM_VFS in case no further active VFs, otherwise index.
  */
 u16 qed_iov_get_next_active_vf(struct qed_hwfn *p_hwfn, u16 rel_vf_id);
 
@@ -280,83 +283,92 @@
 				    int vfid, u16 vxlan_port, u16 geneve_port);
 
 /**
- * @brief Read sriov related information and allocated resources
- *  reads from configuration space, shmem, etc.
+ * qed_iov_hw_info(): Read sriov related information and allocated resources
+ *                    reads from configuration space, shmem, etc.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_iov_hw_info(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_add_tlv - place a given tlv on the tlv buffer at next offset
+ * qed_add_tlv(): place a given tlv on the tlv buffer at next offset
  *
- * @param p_hwfn
- * @param p_iov
- * @param type
- * @param length
+ * @p_hwfn: HW device data.
+ * @offset: offset.
+ * @type: Type
+ * @length: Length.
  *
- * @return pointer to the newly placed tlv
+ * Return: pointer to the newly placed tlv
  */
 void *qed_add_tlv(struct qed_hwfn *p_hwfn, u8 **offset, u16 type, u16 length);
 
 /**
- * @brief list the types and lengths of the tlvs on the buffer
+ * qed_dp_tlv_list(): list the types and lengths of the tlvs on the buffer
  *
- * @param p_hwfn
- * @param tlvs_list
+ * @p_hwfn: HW device data.
+ * @tlvs_list: Tlvs_list.
+ *
+ * Return: Void.
  */
 void qed_dp_tlv_list(struct qed_hwfn *p_hwfn, void *tlvs_list);
 
 /**
- * @brief qed_iov_alloc - allocate sriov related resources
+ * qed_iov_alloc(): allocate sriov related resources
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_iov_alloc(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_iov_setup - setup sriov related resources
+ * qed_iov_setup(): setup sriov related resources
+ *
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
+ * Return: Void.
  */
 void qed_iov_setup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_iov_free - free sriov related resources
+ * qed_iov_free(): free sriov related resources
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
+ *
+ * Return: Void.
  */
 void qed_iov_free(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief free sriov related memory that was allocated during hw_prepare
+ * qed_iov_free_hw_info(): free sriov related memory that was
+ *                          allocated during hw_prepare
+ *
+ * @cdev: Qed dev pointer.
  *
- * @param cdev
+ * Return: Void.
  */
 void qed_iov_free_hw_info(struct qed_dev *cdev);
 
 /**
- * @brief Mark structs of vfs that have been FLR-ed.
+ * qed_iov_mark_vf_flr(): Mark structs of vfs that have been FLR-ed.
  *
- * @param p_hwfn
- * @param disabled_vfs - bitmask of all VFs on path that were FLRed
+ * @p_hwfn: HW device data.
+ * @disabled_vfs: bitmask of all VFs on path that were FLRed
  *
- * @return true iff one of the PF's vfs got FLRed. false otherwise.
+ * Return: true iff one of the PF's vfs got FLRed. false otherwise.
  */
 bool qed_iov_mark_vf_flr(struct qed_hwfn *p_hwfn, u32 *disabled_vfs);
 
 /**
- * @brief Search extended TLVs in request/reply buffer.
+ * qed_iov_search_list_tlvs(): Search extended TLVs in request/reply buffer.
  *
- * @param p_hwfn
- * @param p_tlvs_list - Pointer to tlvs list
- * @param req_type - Type of TLV
+ * @p_hwfn: HW device data.
+ * @p_tlvs_list: Pointer to tlvs list
+ * @req_type: Type of TLV
  *
- * @return pointer to tlv type if found, otherwise returns NULL.
+ * Return: pointer to tlv type if found, otherwise returns NULL.
  */
 void *qed_iov_search_list_tlvs(struct qed_hwfn *p_hwfn,
 			       void *p_tlvs_list, u16 req_type);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_vf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_vf.c
@@ -513,6 +513,9 @@
 						    p_iov->bulletin.size,
 						    &p_iov->bulletin.phys,
 						    GFP_KERNEL);
+	if (!p_iov->bulletin.p_virt)
+		goto free_pf2vf_reply;
+
 	DP_VERBOSE(p_hwfn, QED_MSG_IOV,
 		   "VF's bulletin Board [%p virt 0x%llx phys 0x%08x bytes]\n",
 		   p_iov->bulletin.p_virt,
@@ -552,6 +555,10 @@
 
 	return rc;
 
+free_pf2vf_reply:
+	dma_free_coherent(&p_hwfn->cdev->pdev->dev,
+			  sizeof(union pfvf_tlvs),
+			  p_iov->pf2vf_reply, p_iov->pf2vf_reply_phys);
 free_vf2pf_request:
 	dma_free_coherent(&p_hwfn->cdev->pdev->dev,
 			  sizeof(union vfpf_tlvs),
@@ -1372,7 +1379,7 @@
 
 int
 qed_vf_pf_bulletin_update_mac(struct qed_hwfn *p_hwfn,
-			      u8 *p_mac)
+			      const u8 *p_mac)
 {
 	struct qed_vf_iov *p_iov = p_hwfn->vf_iov_info;
 	struct vfpf_bulletin_update_mac_tlv *p_req;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qed/qed_vf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qed/qed_vf.h
@@ -688,13 +688,16 @@
 };
 
 /**
- * @brief VF - Set Rx/Tx coalesce per VF's relative queue.
- *             Coalesce value '0' will omit the configuration.
+ * qed_vf_pf_set_coalesce(): VF - Set Rx/Tx coalesce per VF's relative queue.
+ *                                Coalesce value '0' will omit the
+ *                                configuration.
+ *
+ * @p_hwfn: HW device data.
+ * @rx_coal: coalesce value in micro second for rx queue.
+ * @tx_coal: coalesce value in micro second for tx queue.
+ * @p_cid: queue cid.
  *
- * @param p_hwfn
- * @param rx_coal - coalesce value in micro second for rx queue
- * @param tx_coal - coalesce value in micro second for tx queue
- * @param p_cid   - queue cid
+ * Return: Int.
  *
  **/
 int qed_vf_pf_set_coalesce(struct qed_hwfn *p_hwfn,
@@ -702,148 +705,172 @@
 			   u16 tx_coal, struct qed_queue_cid *p_cid);
 
 /**
- * @brief VF - Get coalesce per VF's relative queue.
+ * qed_vf_pf_get_coalesce(): VF - Get coalesce per VF's relative queue.
  *
- * @param p_hwfn
- * @param p_coal - coalesce value in micro second for VF queues.
- * @param p_cid  - queue cid
+ * @p_hwfn: HW device data.
+ * @p_coal: coalesce value in micro second for VF queues.
+ * @p_cid: queue cid.
  *
+ * Return: Int.
  **/
 int qed_vf_pf_get_coalesce(struct qed_hwfn *p_hwfn,
 			   u16 *p_coal, struct qed_queue_cid *p_cid);
 
 #ifdef CONFIG_QED_SRIOV
 /**
- * @brief Read the VF bulletin and act on it if needed
+ * qed_vf_read_bulletin(): Read the VF bulletin and act on it if needed.
  *
- * @param p_hwfn
- * @param p_change - qed fills 1 iff bulletin board has changed, 0 otherwise.
+ * @p_hwfn: HW device data.
+ * @p_change: qed fills 1 iff bulletin board has changed, 0 otherwise.
  *
- * @return enum _qed_status
+ * Return: enum _qed_status.
  */
 int qed_vf_read_bulletin(struct qed_hwfn *p_hwfn, u8 *p_change);
 
 /**
- * @brief Get link paramters for VF from qed
+ * qed_vf_get_link_params(): Get link parameters for VF from qed
  *
- * @param p_hwfn
- * @param params - the link params structure to be filled for the VF
+ * @p_hwfn: HW device data.
+ * @params: the link params structure to be filled for the VF.
+ *
+ * Return: Void.
  */
 void qed_vf_get_link_params(struct qed_hwfn *p_hwfn,
 			    struct qed_mcp_link_params *params);
 
 /**
- * @brief Get link state for VF from qed
+ * qed_vf_get_link_state(): Get link state for VF from qed.
+ *
+ * @p_hwfn: HW device data.
+ * @link: the link state structure to be filled for the VF
  *
- * @param p_hwfn
- * @param link - the link state structure to be filled for the VF
+ * Return: Void.
  */
 void qed_vf_get_link_state(struct qed_hwfn *p_hwfn,
 			   struct qed_mcp_link_state *link);
 
 /**
- * @brief Get link capabilities for VF from qed
+ * qed_vf_get_link_caps(): Get link capabilities for VF from qed.
+ *
+ * @p_hwfn: HW device data.
+ * @p_link_caps: the link capabilities structure to be filled for the VF
  *
- * @param p_hwfn
- * @param p_link_caps - the link capabilities structure to be filled for the VF
+ * Return: Void.
  */
 void qed_vf_get_link_caps(struct qed_hwfn *p_hwfn,
 			  struct qed_mcp_link_capabilities *p_link_caps);
 
 /**
- * @brief Get number of Rx queues allocated for VF by qed
+ * qed_vf_get_num_rxqs(): Get number of Rx queues allocated for VF by qed
  *
- *  @param p_hwfn
- *  @param num_rxqs - allocated RX queues
+ * @p_hwfn: HW device data.
+ * @num_rxqs: allocated RX queues
+ *
+ * Return: Void.
  */
 void qed_vf_get_num_rxqs(struct qed_hwfn *p_hwfn, u8 *num_rxqs);
 
 /**
- * @brief Get number of Rx queues allocated for VF by qed
+ * qed_vf_get_num_txqs(): Get number of Rx queues allocated for VF by qed
+ *
+ * @p_hwfn: HW device data.
+ * @num_txqs: allocated RX queues
  *
- *  @param p_hwfn
- *  @param num_txqs - allocated RX queues
+ * Return: Void.
  */
 void qed_vf_get_num_txqs(struct qed_hwfn *p_hwfn, u8 *num_txqs);
 
 /**
- * @brief Get number of available connections [both Rx and Tx] for VF
+ * qed_vf_get_num_cids(): Get number of available connections
+ *                        [both Rx and Tx] for VF
  *
- * @param p_hwfn
- * @param num_cids - allocated number of connections
+ * @p_hwfn: HW device data.
+ * @num_cids: allocated number of connections
+ *
+ * Return: Void.
  */
 void qed_vf_get_num_cids(struct qed_hwfn *p_hwfn, u8 *num_cids);
 
 /**
- * @brief Get port mac address for VF
+ * qed_vf_get_port_mac(): Get port mac address for VF.
+ *
+ * @p_hwfn: HW device data.
+ * @port_mac: destination location for port mac
  *
- * @param p_hwfn
- * @param port_mac - destination location for port mac
+ * Return: Void.
  */
 void qed_vf_get_port_mac(struct qed_hwfn *p_hwfn, u8 *port_mac);
 
 /**
- * @brief Get number of VLAN filters allocated for VF by qed
+ * qed_vf_get_num_vlan_filters(): Get number of VLAN filters allocated
+ *                                for VF by qed.
  *
- *  @param p_hwfn
- *  @param num_rxqs - allocated VLAN filters
+ * @p_hwfn: HW device data.
+ * @num_vlan_filters: allocated VLAN filters
+ *
+ * Return: Void.
  */
 void qed_vf_get_num_vlan_filters(struct qed_hwfn *p_hwfn,
 				 u8 *num_vlan_filters);
 
 /**
- * @brief Get number of MAC filters allocated for VF by qed
+ * qed_vf_get_num_mac_filters(): Get number of MAC filters allocated
+ *                               for VF by qed
+ *
+ * @p_hwfn: HW device data.
+ * @num_mac_filters: allocated MAC filters
  *
- *  @param p_hwfn
- *  @param num_rxqs - allocated MAC filters
+ * Return: Void.
  */
 void qed_vf_get_num_mac_filters(struct qed_hwfn *p_hwfn, u8 *num_mac_filters);
 
 /**
- * @brief Check if VF can set a MAC address
+ * qed_vf_check_mac(): Check if VF can set a MAC address
  *
- * @param p_hwfn
- * @param mac
+ * @p_hwfn: HW device data.
+ * @mac: Mac.
  *
- * @return bool
+ * Return: bool.
  */
 bool qed_vf_check_mac(struct qed_hwfn *p_hwfn, u8 *mac);
 
 /**
- * @brief Set firmware version information in dev_info from VFs acquire response tlv
+ * qed_vf_get_fw_version(): Set firmware version information
+ *                          in dev_info from VFs acquire response tlv
  *
- * @param p_hwfn
- * @param fw_major
- * @param fw_minor
- * @param fw_rev
- * @param fw_eng
+ * @p_hwfn: HW device data.
+ * @fw_major: FW major.
+ * @fw_minor: FW minor.
+ * @fw_rev: FW rev.
+ * @fw_eng: FW eng.
+ *
+ * Return: Void.
  */
 void qed_vf_get_fw_version(struct qed_hwfn *p_hwfn,
 			   u16 *fw_major, u16 *fw_minor,
 			   u16 *fw_rev, u16 *fw_eng);
 
 /**
- * @brief hw preparation for VF
- *      sends ACQUIRE message
+ * qed_vf_hw_prepare(): hw preparation for VF  sends ACQUIRE message
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return int
+ * Return: Int.
  */
 int qed_vf_hw_prepare(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief VF - start the RX Queue by sending a message to the PF
- * @param p_hwfn
- * @param p_cid			- Only relative fields are relevant
- * @param bd_max_bytes          - maximum number of bytes per bd
- * @param bd_chain_phys_addr    - physical address of bd chain
- * @param cqe_pbl_addr          - physical address of pbl
- * @param cqe_pbl_size          - pbl size
- * @param pp_prod               - pointer to the producer to be
- *				  used in fastpath
+ * qed_vf_pf_rxq_start(): start the RX Queue by sending a message to the PF
+ *
+ * @p_hwfn: HW device data.
+ * @p_cid: Only relative fields are relevant
+ * @bd_max_bytes: maximum number of bytes per bd
+ * @bd_chain_phys_addr: physical address of bd chain
+ * @cqe_pbl_addr: physical address of pbl
+ * @cqe_pbl_size: pbl size
+ * @pp_prod: pointer to the producer to be used in fastpath
  *
- * @return int
+ * Return: Int.
  */
 int qed_vf_pf_rxq_start(struct qed_hwfn *p_hwfn,
 			struct qed_queue_cid *p_cid,
@@ -853,18 +880,16 @@
 			u16 cqe_pbl_size, void __iomem **pp_prod);
 
 /**
- * @brief VF - start the TX queue by sending a message to the
- *        PF.
+ * qed_vf_pf_txq_start(): VF - start the TX queue by sending a message to the
+ *                        PF.
  *
- * @param p_hwfn
- * @param tx_queue_id           - zero based within the VF
- * @param sb                    - status block for this queue
- * @param sb_index              - index within the status block
- * @param bd_chain_phys_addr    - physical address of tx chain
- * @param pp_doorbell           - pointer to address to which to
- *                      write the doorbell too..
+ * @p_hwfn: HW device data.
+ * @p_cid: CID.
+ * @pbl_addr: PBL address.
+ * @pbl_size: PBL Size.
+ * @pp_doorbell: pointer to address to which to write the doorbell too.
  *
- * @return int
+ * Return: Int.
  */
 int
 qed_vf_pf_txq_start(struct qed_hwfn *p_hwfn,
@@ -873,90 +898,91 @@
 		    u16 pbl_size, void __iomem **pp_doorbell);
 
 /**
- * @brief VF - stop the RX queue by sending a message to the PF
+ * qed_vf_pf_rxq_stop(): VF - stop the RX queue by sending a message to the PF.
  *
- * @param p_hwfn
- * @param p_cid
- * @param cqe_completion
+ * @p_hwfn: HW device data.
+ * @p_cid: CID.
+ * @cqe_completion: CQE Completion.
  *
- * @return int
+ * Return: Int.
  */
 int qed_vf_pf_rxq_stop(struct qed_hwfn *p_hwfn,
 		       struct qed_queue_cid *p_cid, bool cqe_completion);
 
 /**
- * @brief VF - stop the TX queue by sending a message to the PF
+ * qed_vf_pf_txq_stop(): VF - stop the TX queue by sending a message to the PF.
  *
- * @param p_hwfn
- * @param tx_qid
+ * @p_hwfn: HW device data.
+ * @p_cid: CID.
  *
- * @return int
+ * Return: Int.
  */
 int qed_vf_pf_txq_stop(struct qed_hwfn *p_hwfn, struct qed_queue_cid *p_cid);
 
 /**
- * @brief VF - send a vport update command
+ * qed_vf_pf_vport_update(): VF - send a vport update command.
  *
- * @param p_hwfn
- * @param params
+ * @p_hwfn: HW device data.
+ * @p_params: Params
  *
- * @return int
+ * Return: Int.
  */
 int qed_vf_pf_vport_update(struct qed_hwfn *p_hwfn,
 			   struct qed_sp_vport_update_params *p_params);
 
 /**
+ * qed_vf_pf_reset(): VF - send a close message to PF.
  *
- * @brief VF - send a close message to PF
+ * @p_hwfn: HW device data.
  *
- * @param p_hwfn
- *
- * @return enum _qed_status
+ * Return: enum _qed_status
  */
 int qed_vf_pf_reset(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief VF - free vf`s memories
+ * qed_vf_pf_release(): VF - free vf`s memories.
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return enum _qed_status
+ * Return: enum _qed_status
  */
 int qed_vf_pf_release(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief qed_vf_get_igu_sb_id - Get the IGU SB ID for a given
+ * qed_vf_get_igu_sb_id(): Get the IGU SB ID for a given
  *        sb_id. For VFs igu sbs don't have to be contiguous
  *
- * @param p_hwfn
- * @param sb_id
+ * @p_hwfn: HW device data.
+ * @sb_id: SB ID.
  *
- * @return INLINE u16
+ * Return: INLINE u16
  */
 u16 qed_vf_get_igu_sb_id(struct qed_hwfn *p_hwfn, u16 sb_id);
 
 /**
- * @brief Stores [or removes] a configured sb_info.
+ * qed_vf_set_sb_info(): Stores [or removes] a configured sb_info.
+ *
+ * @p_hwfn: HW device data.
+ * @sb_id: zero-based SB index [for fastpath]
+ * @p_sb:  may be NULL [during removal].
  *
- * @param p_hwfn
- * @param sb_id - zero-based SB index [for fastpath]
- * @param sb_info - may be NULL [during removal].
+ * Return: Void.
  */
 void qed_vf_set_sb_info(struct qed_hwfn *p_hwfn,
 			u16 sb_id, struct qed_sb_info *p_sb);
 
 /**
- * @brief qed_vf_pf_vport_start - perform vport start for VF.
+ * qed_vf_pf_vport_start(): perform vport start for VF.
  *
- * @param p_hwfn
- * @param vport_id
- * @param mtu
- * @param inner_vlan_removal
- * @param tpa_mode
- * @param max_buffers_per_cqe,
- * @param only_untagged - default behavior regarding vlan acceptance
+ * @p_hwfn: HW device data.
+ * @vport_id: Vport ID.
+ * @mtu: MTU.
+ * @inner_vlan_removal: Innter VLAN removal.
+ * @tpa_mode: TPA mode
+ * @max_buffers_per_cqe: Max buffer pre CQE.
+ * @only_untagged: default behavior regarding vlan acceptance
  *
- * @return enum _qed_status
+ * Return: enum _qed_status
  */
 int qed_vf_pf_vport_start(struct qed_hwfn *p_hwfn,
 			  u8 vport_id,
@@ -966,11 +992,11 @@
 			  u8 max_buffers_per_cqe, u8 only_untagged);
 
 /**
- * @brief qed_vf_pf_vport_stop - stop the VF's vport
+ * qed_vf_pf_vport_stop(): stop the VF's vport
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return enum _qed_status
+ * Return: enum _qed_status
  */
 int qed_vf_pf_vport_stop(struct qed_hwfn *p_hwfn);
 
@@ -981,42 +1007,49 @@
 			    struct qed_filter_mcast *p_filter_cmd);
 
 /**
- * @brief qed_vf_pf_int_cleanup - clean the SB of the VF
+ * qed_vf_pf_int_cleanup(): clean the SB of the VF
  *
- * @param p_hwfn
+ * @p_hwfn: HW device data.
  *
- * @return enum _qed_status
+ * Return: enum _qed_status
  */
 int qed_vf_pf_int_cleanup(struct qed_hwfn *p_hwfn);
 
 /**
- * @brief - return the link params in a given bulletin board
+ * __qed_vf_get_link_params(): return the link params in a given bulletin board
  *
- * @param p_hwfn
- * @param p_params - pointer to a struct to fill with link params
- * @param p_bulletin
+ * @p_hwfn: HW device data.
+ * @p_params: pointer to a struct to fill with link params
+ * @p_bulletin: Bulletin.
+ *
+ * Return: Void.
  */
 void __qed_vf_get_link_params(struct qed_hwfn *p_hwfn,
 			      struct qed_mcp_link_params *p_params,
 			      struct qed_bulletin_content *p_bulletin);
 
 /**
- * @brief - return the link state in a given bulletin board
+ * __qed_vf_get_link_state(): return the link state in a given bulletin board
+ *
+ * @p_hwfn: HW device data.
+ * @p_link: pointer to a struct to fill with link state
+ * @p_bulletin: Bulletin.
  *
- * @param p_hwfn
- * @param p_link - pointer to a struct to fill with link state
- * @param p_bulletin
+ * Return: Void.
  */
 void __qed_vf_get_link_state(struct qed_hwfn *p_hwfn,
 			     struct qed_mcp_link_state *p_link,
 			     struct qed_bulletin_content *p_bulletin);
 
 /**
- * @brief - return the link capabilities in a given bulletin board
+ * __qed_vf_get_link_caps(): return the link capabilities in a given
+ *                           bulletin board
  *
- * @param p_hwfn
- * @param p_link - pointer to a struct to fill with link capabilities
- * @param p_bulletin
+ * @p_hwfn: HW device data.
+ * @p_link_caps: pointer to a struct to fill with link capabilities
+ * @p_bulletin: Bulletin.
+ *
+ * Return: Void.
  */
 void __qed_vf_get_link_caps(struct qed_hwfn *p_hwfn,
 			    struct qed_mcp_link_capabilities *p_link_caps,
@@ -1029,11 +1062,15 @@
 
 u32 qed_vf_hw_bar_size(struct qed_hwfn *p_hwfn, enum BAR_ID bar_id);
 /**
- * @brief - Ask PF to update the MAC address in it's bulletin board
+ * qed_vf_pf_bulletin_update_mac(): Ask PF to update the MAC address in
+ *                                  it's bulletin board
+ *
+ * @p_hwfn: HW device data.
+ * @p_mac: mac address to be updated in bulletin board
  *
- * @param p_mac - mac address to be updated in bulletin board
+ * Return: Int.
  */
-int qed_vf_pf_bulletin_update_mac(struct qed_hwfn *p_hwfn, u8 *p_mac);
+int qed_vf_pf_bulletin_update_mac(struct qed_hwfn *p_hwfn, const u8 *p_mac);
 
 #else
 static inline void qed_vf_get_link_params(struct qed_hwfn *p_hwfn,
@@ -1222,7 +1259,7 @@
 }
 
 static inline int qed_vf_pf_bulletin_update_mac(struct qed_hwfn *p_hwfn,
-						u8 *p_mac)
+						const u8 *p_mac)
 {
 	return -EINVAL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qede/qede.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qede/qede.h
@@ -271,6 +271,10 @@
 #define QEDE_ERR_WARN			3
 
 	struct qede_dump_info		dump_info;
+	struct delayed_work		periodic_task;
+	unsigned long			stats_coal_ticks;
+	u32				stats_coal_usecs;
+	spinlock_t			stats_lock; /* lock for vport stats access */
 };
 
 enum QEDE_STATE {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qede/qede_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qede/qede_ethtool.c
@@ -426,6 +426,8 @@
 		}
 	}
 
+	spin_lock(&edev->stats_lock);
+
 	for (i = 0; i < QEDE_NUM_STATS; i++) {
 		if (qede_is_irrelevant_stat(edev, i))
 			continue;
@@ -435,6 +437,8 @@
 		buf++;
 	}
 
+	spin_unlock(&edev->stats_lock);
+
 	__qede_unlock(edev);
 }
 
@@ -817,6 +821,7 @@
 
 	coal->rx_coalesce_usecs = rx_coal;
 	coal->tx_coalesce_usecs = tx_coal;
+	coal->stats_block_coalesce_usecs = edev->stats_coal_usecs;
 
 	return rc;
 }
@@ -830,6 +835,19 @@
 	int i, rc = 0;
 	u16 rxc, txc;
 
+	if (edev->stats_coal_usecs != coal->stats_block_coalesce_usecs) {
+		edev->stats_coal_usecs = coal->stats_block_coalesce_usecs;
+		if (edev->stats_coal_usecs) {
+			edev->stats_coal_ticks = usecs_to_jiffies(edev->stats_coal_usecs);
+			schedule_delayed_work(&edev->periodic_task, 0);
+
+			DP_INFO(edev, "Configured stats coal ticks=%lu jiffies\n",
+				edev->stats_coal_ticks);
+		} else {
+			cancel_delayed_work_sync(&edev->periodic_task);
+		}
+	}
+
 	if (!netif_running(dev)) {
 		DP_INFO(edev, "Interface is down\n");
 		return -EINVAL;
@@ -2236,7 +2254,8 @@
 }
 
 static const struct ethtool_ops qede_ethtool_ops = {
-	.supported_coalesce_params	= ETHTOOL_COALESCE_USECS,
+	.supported_coalesce_params	= ETHTOOL_COALESCE_USECS |
+					  ETHTOOL_COALESCE_STATS_BLOCK_USECS,
 	.get_link_ksettings		= qede_get_link_ksettings,
 	.set_link_ksettings		= qede_set_link_ksettings,
 	.get_drvinfo			= qede_get_drvinfo,
@@ -2287,7 +2306,8 @@
 };
 
 static const struct ethtool_ops qede_vf_ethtool_ops = {
-	.supported_coalesce_params	= ETHTOOL_COALESCE_USECS,
+	.supported_coalesce_params	= ETHTOOL_COALESCE_USECS |
+					  ETHTOOL_COALESCE_STATS_BLOCK_USECS,
 	.get_link_ksettings		= qede_get_link_ksettings,
 	.get_drvinfo			= qede_get_drvinfo,
 	.get_msglevel			= qede_get_msglevel,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qede/qede_filter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qede/qede_filter.c
@@ -557,7 +557,7 @@
 		return;
 	}
 
-	ether_addr_copy(edev->ndev->dev_addr, mac);
+	eth_hw_addr_set(edev->ndev, mac);
 	__qede_unlock(edev);
 }
 
@@ -617,32 +617,30 @@
 
 static int qede_set_ucast_rx_mac(struct qede_dev *edev,
 				 enum qed_filter_xcast_params_type opcode,
-				 unsigned char mac[ETH_ALEN])
+				 const unsigned char mac[ETH_ALEN])
 {
-	struct qed_filter_params filter_cmd;
+	struct qed_filter_ucast_params ucast;
 
-	memset(&filter_cmd, 0, sizeof(filter_cmd));
-	filter_cmd.type = QED_FILTER_TYPE_UCAST;
-	filter_cmd.filter.ucast.type = opcode;
-	filter_cmd.filter.ucast.mac_valid = 1;
-	ether_addr_copy(filter_cmd.filter.ucast.mac, mac);
+	memset(&ucast, 0, sizeof(ucast));
+	ucast.type = opcode;
+	ucast.mac_valid = 1;
+	ether_addr_copy(ucast.mac, mac);
 
-	return edev->ops->filter_config(edev->cdev, &filter_cmd);
+	return edev->ops->filter_config_ucast(edev->cdev, &ucast);
 }
 
 static int qede_set_ucast_rx_vlan(struct qede_dev *edev,
 				  enum qed_filter_xcast_params_type opcode,
 				  u16 vid)
 {
-	struct qed_filter_params filter_cmd;
+	struct qed_filter_ucast_params ucast;
 
-	memset(&filter_cmd, 0, sizeof(filter_cmd));
-	filter_cmd.type = QED_FILTER_TYPE_UCAST;
-	filter_cmd.filter.ucast.type = opcode;
-	filter_cmd.filter.ucast.vlan_valid = 1;
-	filter_cmd.filter.ucast.vlan = vid;
+	memset(&ucast, 0, sizeof(ucast));
+	ucast.type = opcode;
+	ucast.vlan_valid = 1;
+	ucast.vlan = vid;
 
-	return edev->ops->filter_config(edev->cdev, &filter_cmd);
+	return edev->ops->filter_config_ucast(edev->cdev, &ucast);
 }
 
 static int qede_config_accept_any_vlan(struct qede_dev *edev, bool action)
@@ -1057,18 +1055,17 @@
 				 enum qed_filter_xcast_params_type opcode,
 				 unsigned char *mac, int num_macs)
 {
-	struct qed_filter_params filter_cmd;
+	struct qed_filter_mcast_params mcast;
 	int i;
 
-	memset(&filter_cmd, 0, sizeof(filter_cmd));
-	filter_cmd.type = QED_FILTER_TYPE_MCAST;
-	filter_cmd.filter.mcast.type = opcode;
-	filter_cmd.filter.mcast.num = num_macs;
+	memset(&mcast, 0, sizeof(mcast));
+	mcast.type = opcode;
+	mcast.num = num_macs;
 
 	for (i = 0; i < num_macs; i++, mac += ETH_ALEN)
-		ether_addr_copy(filter_cmd.filter.mcast.mac[i], mac);
+		ether_addr_copy(mcast.mac[i], mac);
 
-	return edev->ops->filter_config(edev->cdev, &filter_cmd);
+	return edev->ops->filter_config_mcast(edev->cdev, &mcast);
 }
 
 int qede_set_mac_addr(struct net_device *ndev, void *p)
@@ -1104,7 +1101,7 @@
 			goto out;
 	}
 
-	ether_addr_copy(ndev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(ndev, addr->sa_data);
 	DP_INFO(edev, "Setting device MAC to %pM\n", addr->sa_data);
 
 	if (edev->state != QEDE_STATE_OPEN) {
@@ -1194,7 +1191,6 @@
 {
 	enum qed_filter_rx_mode_type accept_flags;
 	struct qede_dev *edev = netdev_priv(ndev);
-	struct qed_filter_params rx_mode;
 	unsigned char *uc_macs, *temp;
 	struct netdev_hw_addr *ha;
 	int rc, uc_count;
@@ -1220,10 +1216,6 @@
 
 	netif_addr_unlock_bh(ndev);
 
-	/* Configure the struct for the Rx mode */
-	memset(&rx_mode, 0, sizeof(struct qed_filter_params));
-	rx_mode.type = QED_FILTER_TYPE_RX_MODE;
-
 	/* Remove all previous unicast secondary macs and multicast macs
 	 * (configure / leave the primary mac)
 	 */
@@ -1271,8 +1263,7 @@
 		qede_config_accept_any_vlan(edev, false);
 	}
 
-	rx_mode.filter.accept_flags = accept_flags;
-	edev->ops->filter_config(edev->cdev, &rx_mode);
+	edev->ops->filter_config_rx_mode(edev->cdev, accept_flags);
 out:
 	kfree(uc_macs);
 }
@@ -1877,8 +1868,8 @@
 			    struct flow_cls_offload *f)
 {
 	struct qede_arfs_fltr_node *n;
-	int min_hlen, rc = -EINVAL;
 	struct qede_arfs_tuple t;
+	int min_hlen, rc;
 
 	__qede_lock(edev);
 
@@ -1888,7 +1879,8 @@
 	}
 
 	/* parse flower attribute and prepare filter */
-	if (qede_parse_flow_attr(edev, proto, f->rule, &t))
+	rc = qede_parse_flow_attr(edev, proto, f->rule, &t);
+	if (rc)
 		goto unlock;
 
 	/* Validate profile mode and number of filters */
@@ -1897,11 +1889,13 @@
 		DP_NOTICE(edev,
 			  "Filter configuration invalidated, filter mode=0x%x, configured mode=0x%x, filter count=0x%x\n",
 			  t.mode, edev->arfs->mode, edev->arfs->filter_count);
+		rc = -EINVAL;
 		goto unlock;
 	}
 
 	/* parse tc actions and get the vf_id */
-	if (qede_parse_actions(edev, &f->rule->action, f->common.extack))
+	rc = qede_parse_actions(edev, &f->rule->action, f->common.extack);
+	if (rc)
 		goto unlock;
 
 	if (qede_flow_find_fltr(edev, &t)) {
@@ -2007,10 +2001,9 @@
 	if (IS_ERR(flow))
 		return PTR_ERR(flow);
 
-	if (qede_parse_flow_attr(edev, proto, flow->rule, t)) {
-		err = -EINVAL;
+	err = qede_parse_flow_attr(edev, proto, flow->rule, t);
+	if (err)
 		goto err_out;
-	}
 
 	/* Make sure location is valid and filter isn't already set */
 	err = qede_flow_spec_validate(edev, &flow->rule->action, t,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qede/qede_fp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qede/qede_fp.c
@@ -747,6 +747,9 @@
 	buf = page_address(bd->data) + bd->page_offset;
 	skb = build_skb(buf, rxq->rx_buf_seg_size);
 
+	if (unlikely(!skb))
+		return NULL;
+
 	skb_reserve(skb, pad);
 	skb_put(skb, len);
 
@@ -1436,6 +1439,10 @@
 	rx_work_done = (likely(fp->type & QEDE_FASTPATH_RX) &&
 			qede_has_rx_work(fp->rxq)) ?
 			qede_rx_int(fp, budget) : 0;
+
+	if (fp->xdp_xmit & QEDE_XDP_REDIRECT)
+		xdp_do_flush();
+
 	/* Handle case where we are called by netpoll with a budget of 0 */
 	if (rx_work_done < budget || !budget) {
 		if (!qede_poll_is_more_work(fp)) {
@@ -1455,9 +1462,6 @@
 		qede_update_tx_producer(fp->xdp_tx);
 	}
 
-	if (fp->xdp_xmit & QEDE_XDP_REDIRECT)
-		xdp_do_flush_map();
-
 	return rx_work_done;
 }
 
@@ -1643,6 +1647,13 @@
 			data_split = true;
 		}
 	} else {
+		if (unlikely(skb->len > ETH_TX_MAX_NON_LSO_PKT_LEN)) {
+			DP_ERR(edev, "Unexpected non LSO skb length = 0x%x\n", skb->len);
+			qede_free_failed_tx_pkt(txq, first_bd, 0, false);
+			qede_update_tx_producer(txq);
+			return NETDEV_TX_OK;
+		}
+
 		val |= ((skb->len & ETH_TX_DATA_1ST_BD_PKT_LEN_MASK) <<
 			 ETH_TX_DATA_1ST_BD_PKT_LEN_SHIFT);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qede/qede_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qede/qede_main.c
@@ -308,6 +308,8 @@
 
 	edev->ops->get_vport_stats(edev->cdev, &stats);
 
+	spin_lock(&edev->stats_lock);
+
 	p_common->no_buff_discards = stats.common.no_buff_discards;
 	p_common->packet_too_big_discard = stats.common.packet_too_big_discard;
 	p_common->ttl0_discard = stats.common.ttl0_discard;
@@ -405,6 +407,8 @@
 		p_ah->tx_1519_to_max_byte_packets =
 		    stats.ah.tx_1519_to_max_byte_packets;
 	}
+
+	spin_unlock(&edev->stats_lock);
 }
 
 static void qede_get_stats64(struct net_device *dev,
@@ -413,9 +417,10 @@
 	struct qede_dev *edev = netdev_priv(dev);
 	struct qede_stats_common *p_common;
 
-	qede_fill_by_demand_stats(edev);
 	p_common = &edev->stats.common;
 
+	spin_lock(&edev->stats_lock);
+
 	stats->rx_packets = p_common->rx_ucast_pkts + p_common->rx_mcast_pkts +
 			    p_common->rx_bcast_pkts;
 	stats->tx_packets = p_common->tx_ucast_pkts + p_common->tx_mcast_pkts +
@@ -435,6 +440,8 @@
 		stats->collisions = edev->stats.bb.tx_total_collisions;
 	stats->rx_crc_errors = p_common->rx_crc_errors;
 	stats->rx_frame_errors = p_common->rx_align_errors;
+
+	spin_unlock(&edev->stats_lock);
 }
 
 #ifdef CONFIG_QED_SRIOV
@@ -836,7 +843,7 @@
 	ndev->max_mtu = QEDE_MAX_JUMBO_PACKET_SIZE;
 
 	/* Set network device HW mac */
-	ether_addr_copy(edev->ndev->dev_addr, edev->dev_info.common.hw_mac);
+	eth_hw_addr_set(edev->ndev, edev->dev_info.common.hw_mac);
 
 	ndev->mtu = edev->dev_info.common.mtu;
 }
@@ -899,7 +906,6 @@
 {
 	u8 fp_combined, fp_rx = edev->fp_num_rx;
 	struct qede_fastpath *fp;
-	void *mem;
 	int i;
 
 	edev->fp_array = kcalloc(QEDE_QUEUE_CNT(edev),
@@ -909,14 +915,15 @@
 		goto err;
 	}
 
-	mem = krealloc(edev->coal_entry, QEDE_QUEUE_CNT(edev) *
-		       sizeof(*edev->coal_entry), GFP_KERNEL);
-	if (!mem) {
-		DP_ERR(edev, "coalesce entry allocation failed\n");
-		kfree(edev->coal_entry);
-		goto err;
+	if (!edev->coal_entry) {
+		edev->coal_entry = kcalloc(QEDE_MAX_RSS_CNT(edev),
+					   sizeof(*edev->coal_entry),
+					   GFP_KERNEL);
+		if (!edev->coal_entry) {
+			DP_ERR(edev, "coalesce entry allocation failed\n");
+			goto err;
+		}
 	}
-	edev->coal_entry = mem;
 
 	fp_combined = QEDE_QUEUE_CNT(edev) - fp_rx - edev->fp_num_tx;
 
@@ -1000,6 +1007,23 @@
 	rtnl_unlock();
 }
 
+static void qede_periodic_task(struct work_struct *work)
+{
+	struct qede_dev *edev = container_of(work, struct qede_dev,
+					     periodic_task.work);
+
+	qede_fill_by_demand_stats(edev);
+	schedule_delayed_work(&edev->periodic_task, edev->stats_coal_ticks);
+}
+
+static void qede_init_periodic_task(struct qede_dev *edev)
+{
+	INIT_DELAYED_WORK(&edev->periodic_task, qede_periodic_task);
+	spin_lock_init(&edev->stats_lock);
+	edev->stats_coal_usecs = USEC_PER_SEC;
+	edev->stats_coal_ticks = usecs_to_jiffies(USEC_PER_SEC);
+}
+
 static void qede_sp_task(struct work_struct *work)
 {
 	struct qede_dev *edev = container_of(work, struct qede_dev,
@@ -1019,6 +1043,7 @@
 	 */
 
 	if (test_and_clear_bit(QEDE_SP_RECOVERY, &edev->sp_flags)) {
+		cancel_delayed_work_sync(&edev->periodic_task);
 #ifdef CONFIG_QED_SRIOV
 		/* SRIOV must be disabled outside the lock to avoid a deadlock.
 		 * The recovery of the active VFs is currently not supported.
@@ -1176,19 +1201,17 @@
 		edev->devlink = qed_ops->common->devlink_register(cdev);
 		if (IS_ERR(edev->devlink)) {
 			DP_NOTICE(edev, "Cannot register devlink\n");
+			rc = PTR_ERR(edev->devlink);
 			edev->devlink = NULL;
-			/* Go on, we can live without devlink */
+			goto err3;
 		}
 	} else {
 		struct net_device *ndev = pci_get_drvdata(pdev);
+		struct qed_devlink *qdl;
 
 		edev = netdev_priv(ndev);
-
-		if (edev->devlink) {
-			struct qed_devlink *qdl = devlink_priv(edev->devlink);
-
-			qdl->cdev = cdev;
-		}
+		qdl = devlink_priv(edev->devlink);
+		qdl->cdev = cdev;
 		edev->cdev = cdev;
 		memset(&edev->stats, 0, sizeof(edev->stats));
 		memcpy(&edev->dev_info, &dev_info, sizeof(dev_info));
@@ -1211,6 +1234,7 @@
 		 */
 		INIT_DELAYED_WORK(&edev->sp_task, qede_sp_task);
 		mutex_init(&edev->qede_lock);
+		qede_init_periodic_task(edev);
 
 		rc = register_netdev(edev->ndev);
 		if (rc) {
@@ -1235,6 +1259,11 @@
 	edev->rx_copybreak = QEDE_RX_HDR_SIZE;
 
 	qede_log_probe(edev);
+
+	/* retain user config (for example - after recovery) */
+	if (edev->stats_coal_usecs)
+		schedule_delayed_work(&edev->periodic_task, 0);
+
 	return 0;
 
 err4:
@@ -1303,6 +1332,7 @@
 		unregister_netdev(ndev);
 
 		cancel_delayed_work_sync(&edev->sp_task);
+		cancel_delayed_work_sync(&edev->periodic_task);
 
 		edev->ops->common->set_power_state(cdev, PCI_D0);
 
@@ -2802,10 +2832,13 @@
 }
 
 /**
- * qede_io_error_detected - called when PCI error is detected
+ * qede_io_error_detected(): Called when PCI error is detected
+ *
  * @pdev: Pointer to PCI device
  * @state: The current pci connection state
  *
+ *Return: pci_ers_result_t.
+ *
  * This function is called after a PCI bus error affecting
  * this device has been detected.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qla3xxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qla3xxx.c
@@ -2469,6 +2469,7 @@
 					     skb_shinfo(skb)->nr_frags);
 	if (tx_cb->seg_count == -1) {
 		netdev_err(ndev, "%s: invalid segment count!\n", __func__);
+		dev_kfree_skb_any(skb);
 		return NETDEV_TX_OK;
 	}
 
@@ -2588,6 +2589,7 @@
 
 	if (qdev->lrg_buf_q_alloc_virt_addr == NULL) {
 		netdev_err(qdev->ndev, "lBufQ failed\n");
+		kfree(qdev->lrg_buf);
 		return -ENOMEM;
 	}
 	qdev->lrg_buf_q_virt_addr = qdev->lrg_buf_q_alloc_virt_addr;
@@ -2612,6 +2614,7 @@
 				  qdev->lrg_buf_q_alloc_size,
 				  qdev->lrg_buf_q_alloc_virt_addr,
 				  qdev->lrg_buf_q_alloc_phy_addr);
+		kfree(qdev->lrg_buf);
 		return -ENOMEM;
 	}
 
@@ -3478,20 +3481,19 @@
 
 	spin_lock_irqsave(&qdev->hw_lock, hw_flags);
 
-	err = ql_wait_for_drvr_lock(qdev);
-	if (err) {
-		err = ql_adapter_initialize(qdev);
-		if (err) {
-			netdev_err(ndev, "Unable to initialize adapter\n");
-			goto err_init;
-		}
-		netdev_err(ndev, "Releasing driver lock\n");
-		ql_sem_unlock(qdev, QL_DRVR_SEM_MASK);
-	} else {
+	if (!ql_wait_for_drvr_lock(qdev)) {
 		netdev_err(ndev, "Could not acquire driver lock\n");
+		err = -ENODEV;
 		goto err_lock;
 	}
 
+	err = ql_adapter_initialize(qdev);
+	if (err) {
+		netdev_err(ndev, "Unable to initialize adapter\n");
+		goto err_init;
+	}
+	ql_sem_unlock(qdev, QL_DRVR_SEM_MASK);
+
 	spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
 
 	set_bit(QL_ADAPTER_UP, &qdev->flags);
@@ -3613,7 +3615,8 @@
 		qdev->mem_map_registers;
 	unsigned long hw_flags;
 
-	if (test_bit((QL_RESET_PER_SCSI | QL_RESET_START), &qdev->flags)) {
+	if (test_bit(QL_RESET_PER_SCSI, &qdev->flags) ||
+	    test_bit(QL_RESET_START, &qdev->flags)) {
 		clear_bit(QL_LINK_MASTER, &qdev->flags);
 
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
@@ -1077,8 +1077,14 @@
 	sds_mbx_size = sizeof(struct qlcnic_sds_mbx);
 	context_id = recv_ctx->context_id;
 	num_sds = adapter->drv_sds_rings - QLCNIC_MAX_SDS_RINGS;
-	ahw->hw_ops->alloc_mbx_args(&cmd, adapter,
-				    QLCNIC_CMD_ADD_RCV_RINGS);
+	err = ahw->hw_ops->alloc_mbx_args(&cmd, adapter,
+					QLCNIC_CMD_ADD_RCV_RINGS);
+	if (err) {
+		dev_err(&adapter->pdev->dev,
+			"Failed to alloc mbx args %d\n", err);
+		return err;
+	}
+
 	cmd.req.arg[1] = 0 | (num_sds << 8) | (context_id << 16);
 
 	/* set up status rings, mbx 2-81 */
@@ -2985,7 +2991,7 @@
 		QLCWRX(adapter->ahw, QLC_83XX_RECOVER_DRV_LOCK, val);
 		dev_info(&adapter->pdev->dev,
 			 "%s: lock recovery initiated\n", __func__);
-		msleep(QLC_83XX_DRV_LOCK_RECOVERY_DELAY);
+		mdelay(QLC_83XX_DRV_LOCK_RECOVERY_DELAY);
 		val = QLCRDX(adapter->ahw, QLC_83XX_RECOVER_DRV_LOCK);
 		id = ((val >> 2) & 0xF);
 		if (id == adapter->portnum) {
@@ -3021,7 +3027,7 @@
 		if (status)
 			break;
 
-		msleep(QLC_83XX_DRV_LOCK_WAIT_DELAY);
+		mdelay(QLC_83XX_DRV_LOCK_WAIT_DELAY);
 		i++;
 
 		if (i == 1)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c
@@ -2505,7 +2505,13 @@
 		goto disable_mbx_intr;
 
 	qlcnic_83xx_clear_function_resources(adapter);
-	qlcnic_dcb_enable(adapter->dcb);
+
+	err = qlcnic_dcb_enable(adapter->dcb);
+	if (err) {
+		qlcnic_dcb_free(adapter->dcb);
+		goto disable_mbx_intr;
+	}
+
 	qlcnic_83xx_initialize_nic(adapter, 1);
 	qlcnic_dcb_get_info(adapter->dcb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ctx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ctx.c
@@ -628,7 +628,13 @@
 	int i, err, ring;
 
 	if (dev->flags & QLCNIC_NEED_FLR) {
-		pci_reset_function(dev->pdev);
+		err = pci_reset_function(dev->pdev);
+		if (err) {
+			dev_err(&dev->pdev->dev,
+				"Adapter reset failed (%d). Please reboot\n",
+				err);
+			return err;
+		}
 		dev->flags &= ~QLCNIC_NEED_FLR;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h
@@ -41,17 +41,12 @@
 	unsigned long			state;
 };
 
-static inline void qlcnic_clear_dcb_ops(struct qlcnic_dcb *dcb)
-{
-	kfree(dcb);
-}
-
 static inline int qlcnic_dcb_get_hw_capability(struct qlcnic_dcb *dcb)
 {
 	if (dcb && dcb->ops->get_hw_capability)
 		return dcb->ops->get_hw_capability(dcb);
 
-	return 0;
+	return -EOPNOTSUPP;
 }
 
 static inline void qlcnic_dcb_free(struct qlcnic_dcb *dcb)
@@ -65,7 +60,7 @@
 	if (dcb && dcb->ops->attach)
 		return dcb->ops->attach(dcb);
 
-	return 0;
+	return -EOPNOTSUPP;
 }
 
 static inline int
@@ -74,7 +69,7 @@
 	if (dcb && dcb->ops->query_hw_capability)
 		return dcb->ops->query_hw_capability(dcb, buf);
 
-	return 0;
+	return -EOPNOTSUPP;
 }
 
 static inline void qlcnic_dcb_get_info(struct qlcnic_dcb *dcb)
@@ -89,7 +84,7 @@
 	if (dcb && dcb->ops->query_cee_param)
 		return dcb->ops->query_cee_param(dcb, buf, type);
 
-	return 0;
+	return -EOPNOTSUPP;
 }
 
 static inline int qlcnic_dcb_get_cee_cfg(struct qlcnic_dcb *dcb)
@@ -97,7 +92,7 @@
 	if (dcb && dcb->ops->get_cee_cfg)
 		return dcb->ops->get_cee_cfg(dcb);
 
-	return 0;
+	return -EOPNOTSUPP;
 }
 
 static inline void qlcnic_dcb_aen_handler(struct qlcnic_dcb *dcb, void *msg)
@@ -112,9 +107,8 @@
 		dcb->ops->init_dcbnl_ops(dcb);
 }
 
-static inline void qlcnic_dcb_enable(struct qlcnic_dcb *dcb)
+static inline int qlcnic_dcb_enable(struct qlcnic_dcb *dcb)
 {
-	if (dcb && qlcnic_dcb_attach(dcb))
-		qlcnic_clear_dcb_ops(dcb);
+	return dcb ? qlcnic_dcb_attach(dcb) : 0;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c
@@ -317,7 +317,7 @@
 
 	if (adapter->flags & QLCNIC_VLAN_FILTERING) {
 		if (protocol == ETH_P_8021Q) {
-			vh = (struct vlan_ethhdr *)skb->data;
+			vh = skb_vlan_eth_hdr(skb);
 			vlan_id = ntohs(vh->h_vlan_TCI);
 		} else if (skb_vlan_tag_present(skb)) {
 			vlan_id = skb_vlan_tag_get(skb);
@@ -467,7 +467,7 @@
 	u32 producer = tx_ring->producer;
 
 	if (protocol == ETH_P_8021Q) {
-		vh = (struct vlan_ethhdr *)skb->data;
+		vh = skb_vlan_eth_hdr(skb);
 		flags = QLCNIC_FLAGS_VLAN_TAGGED;
 		vlan_tci = ntohs(vh->h_vlan_TCI);
 		protocol = ntohs(vh->h_vlan_encapsulated_proto);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
@@ -2616,7 +2616,13 @@
 			 "Device does not support MSI interrupts\n");
 
 	if (qlcnic_82xx_check(adapter)) {
-		qlcnic_dcb_enable(adapter->dcb);
+		err = qlcnic_dcb_enable(adapter->dcb);
+		if (err) {
+			qlcnic_dcb_free(adapter->dcb);
+			dev_err(&pdev->dev, "Failed to enable DCB\n");
+			goto err_out_free_hw;
+		}
+
 		qlcnic_dcb_get_info(adapter->dcb);
 		err = qlcnic_setup_intr(adapter);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h
@@ -201,7 +201,7 @@
 				   struct qlcnic_info *, u16);
 int qlcnic_sriov_cfg_vf_guest_vlan(struct qlcnic_adapter *, u16, u8);
 void qlcnic_sriov_free_vlans(struct qlcnic_adapter *);
-void qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *);
+int qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *);
 bool qlcnic_sriov_check_any_vlan(struct qlcnic_vf_info *);
 void qlcnic_sriov_del_vlan_id(struct qlcnic_sriov *,
 			      struct qlcnic_vf_info *, u16);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
@@ -221,6 +221,8 @@
 	return 0;
 
 qlcnic_destroy_async_wq:
+	while (i--)
+		kfree(sriov->vf_info[i].vp);
 	destroy_workqueue(bc->bc_async_wq);
 
 qlcnic_destroy_trans_wq:
@@ -432,7 +434,7 @@
 					    struct qlcnic_cmd_args *cmd)
 {
 	struct qlcnic_sriov *sriov = adapter->ahw->sriov;
-	int i, num_vlans;
+	int i, num_vlans, ret;
 	u16 *vlans;
 
 	if (sriov->allowed_vlans)
@@ -443,15 +445,19 @@
 	dev_info(&adapter->pdev->dev, "Number of allowed Guest VLANs = %d\n",
 		 sriov->num_allowed_vlans);
 
-	qlcnic_sriov_alloc_vlans(adapter);
+	ret = qlcnic_sriov_alloc_vlans(adapter);
+	if (ret)
+		return ret;
 
 	if (!sriov->any_vlan)
 		return 0;
 
 	num_vlans = sriov->num_allowed_vlans;
 	sriov->allowed_vlans = kcalloc(num_vlans, sizeof(u16), GFP_KERNEL);
-	if (!sriov->allowed_vlans)
+	if (!sriov->allowed_vlans) {
+		qlcnic_sriov_free_vlans(adapter);
 		return -ENOMEM;
+	}
 
 	vlans = (u16 *)&cmd->rsp.arg[3];
 	for (i = 0; i < num_vlans; i++)
@@ -2154,7 +2160,7 @@
 	return err;
 }
 
-void qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *adapter)
+int qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *adapter)
 {
 	struct qlcnic_sriov *sriov = adapter->ahw->sriov;
 	struct qlcnic_vf_info *vf;
@@ -2164,7 +2170,13 @@
 		vf = &sriov->vf_info[i];
 		vf->sriov_vlans = kcalloc(sriov->num_allowed_vlans,
 					  sizeof(*vf->sriov_vlans), GFP_KERNEL);
+		if (!vf->sriov_vlans) {
+			qlcnic_sriov_free_vlans(adapter);
+			return -ENOMEM;
+		}
 	}
+
+	return 0;
 }
 
 void qlcnic_sriov_free_vlans(struct qlcnic_adapter *adapter)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
@@ -597,7 +597,9 @@
 	if (err)
 		goto del_flr_queue;
 
-	qlcnic_sriov_alloc_vlans(adapter);
+	err = qlcnic_sriov_alloc_vlans(adapter);
+	if (err)
+		goto del_flr_queue;
 
 	return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/emac/emac-mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/emac/emac-mac.c
@@ -420,7 +420,7 @@
 }
 
 /* set MAC address */
-static void emac_set_mac_address(struct emac_adapter *adpt, u8 *addr)
+static void emac_set_mac_address(struct emac_adapter *adpt, const u8 *addr)
 {
 	u32 sta;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/emac/emac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/emac/emac.c
@@ -550,7 +550,7 @@
 
 	/* get mac address */
 	if (device_get_mac_address(&pdev->dev, maddr, ETH_ALEN))
-		ether_addr_copy(netdev->dev_addr, maddr);
+		eth_hw_addr_set(netdev, maddr);
 	else
 		eth_hw_addr_random(netdev);
 
@@ -728,9 +728,15 @@
 	struct net_device *netdev = dev_get_drvdata(&pdev->dev);
 	struct emac_adapter *adpt = netdev_priv(netdev);
 
+	netif_carrier_off(netdev);
+	netif_tx_disable(netdev);
+
 	unregister_netdev(netdev);
 	netif_napi_del(&adpt->rx_q.napi);
 
+	free_irq(adpt->irq.irq, &adpt->irq);
+	cancel_work_sync(&adpt->work_thread);
+
 	emac_clks_teardown(adpt);
 
 	put_device(&adpt->phydev->mdio.dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/qca_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/qca_debug.c
@@ -30,6 +30,8 @@
 
 #define QCASPI_MAX_REGS 0x20
 
+#define QCASPI_RX_MAX_FRAMES 4
+
 static const u16 qcaspi_spi_regs[] = {
 	SPI_REG_BFR_SIZE,
 	SPI_REG_WRBUF_SPC_AVA,
@@ -109,10 +111,8 @@
 
 	seq_printf(s, "IRQ              : %d\n",
 		   qca->spi_dev->irq);
-	seq_printf(s, "INTR REQ         : %u\n",
-		   qca->intr_req);
-	seq_printf(s, "INTR SVC         : %u\n",
-		   qca->intr_svc);
+	seq_printf(s, "INTR             : %lx\n",
+		   qca->intr);
 
 	seq_printf(s, "SPI max speed    : %lu\n",
 		   (unsigned long)qca->spi_dev->max_speed_hz);
@@ -250,31 +250,30 @@
 {
 	struct qcaspi *qca = netdev_priv(dev);
 
-	ring->rx_max_pending = 4;
+	ring->rx_max_pending = QCASPI_RX_MAX_FRAMES;
 	ring->tx_max_pending = TX_RING_MAX_LEN;
-	ring->rx_pending = 4;
+	ring->rx_pending = QCASPI_RX_MAX_FRAMES;
 	ring->tx_pending = qca->txr.count;
 }
 
 static int
 qcaspi_set_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
 {
-	const struct net_device_ops *ops = dev->netdev_ops;
 	struct qcaspi *qca = netdev_priv(dev);
 
-	if ((ring->rx_pending) ||
+	if (ring->rx_pending != QCASPI_RX_MAX_FRAMES ||
 	    (ring->rx_mini_pending) ||
 	    (ring->rx_jumbo_pending))
 		return -EINVAL;
 
-	if (netif_running(dev))
-		ops->ndo_stop(dev);
+	if (qca->spi_thread)
+		kthread_park(qca->spi_thread);
 
 	qca->txr.count = max_t(u32, ring->tx_pending, TX_RING_MIN_LEN);
 	qca->txr.count = min_t(u16, qca->txr.count, TX_RING_MAX_LEN);
 
-	if (netif_running(dev))
-		ops->ndo_open(dev);
+	if (qca->spi_thread)
+		kthread_unpark(qca->spi_thread);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/qca_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/qca_spi.c
@@ -49,6 +49,8 @@
 
 #define MAX_DMA_BURST_LEN 5000
 
+#define SPI_INTR 0
+
 /*   Modules parameters     */
 #define QCASPI_CLK_SPEED_MIN 1000000
 #define QCASPI_CLK_SPEED_MAX 16000000
@@ -65,7 +67,7 @@
 
 #define QCASPI_PLUGGABLE_MIN 0
 #define QCASPI_PLUGGABLE_MAX 1
-static int qcaspi_pluggable = QCASPI_PLUGGABLE_MIN;
+static int qcaspi_pluggable = QCASPI_PLUGGABLE_MAX;
 module_param(qcaspi_pluggable, int, 0);
 MODULE_PARM_DESC(qcaspi_pluggable, "Pluggable SPI connection (yes/no).");
 
@@ -581,15 +583,26 @@
 	netdev_info(qca->net_dev, "SPI thread created\n");
 	while (!kthread_should_stop()) {
 		set_current_state(TASK_INTERRUPTIBLE);
-		if ((qca->intr_req == qca->intr_svc) &&
-		    (qca->txr.skb[qca->txr.head] == NULL) &&
-		    (qca->sync == QCASPI_SYNC_READY))
+		if (kthread_should_park()) {
+			netif_tx_disable(qca->net_dev);
+			netif_carrier_off(qca->net_dev);
+			qcaspi_flush_tx_ring(qca);
+			kthread_parkme();
+			if (qca->sync == QCASPI_SYNC_READY) {
+				netif_carrier_on(qca->net_dev);
+				netif_wake_queue(qca->net_dev);
+			}
+			continue;
+		}
+
+		if (!test_bit(SPI_INTR, &qca->intr) &&
+		    !qca->txr.skb[qca->txr.head])
 			schedule();
 
 		set_current_state(TASK_RUNNING);
 
-		netdev_dbg(qca->net_dev, "have work to do. int: %d, tx_skb: %p\n",
-			   qca->intr_req - qca->intr_svc,
+		netdev_dbg(qca->net_dev, "have work to do. int: %lu, tx_skb: %p\n",
+			   qca->intr,
 			   qca->txr.skb[qca->txr.head]);
 
 		qcaspi_qca7k_sync(qca, QCASPI_EVENT_UPDATE);
@@ -603,18 +616,23 @@
 			msleep(QCASPI_QCA7K_REBOOT_TIME_MS);
 		}
 
-		if (qca->intr_svc != qca->intr_req) {
-			qca->intr_svc = qca->intr_req;
+		if (test_and_clear_bit(SPI_INTR, &qca->intr)) {
 			start_spi_intr_handling(qca, &intr_cause);
 
 			if (intr_cause & SPI_INT_CPU_ON) {
 				qcaspi_qca7k_sync(qca, QCASPI_EVENT_CPUON);
 
+				/* Frame decoding in progress */
+				if (qca->frm_handle.state != qca->frm_handle.init)
+					qca->net_dev->stats.rx_dropped++;
+
+				qcafrm_fsm_init_spi(&qca->frm_handle);
+				qca->stats.device_reset++;
+
 				/* not synced. */
 				if (qca->sync != QCASPI_SYNC_READY)
 					continue;
 
-				qca->stats.device_reset++;
 				netif_wake_queue(qca->net_dev);
 				netif_carrier_on(qca->net_dev);
 			}
@@ -660,7 +678,7 @@
 {
 	struct qcaspi *qca = data;
 
-	qca->intr_req++;
+	set_bit(SPI_INTR, &qca->intr);
 	if (qca->spi_thread)
 		wake_up_process(qca->spi_thread);
 
@@ -676,8 +694,7 @@
 	if (!qca)
 		return -EINVAL;
 
-	qca->intr_req = 1;
-	qca->intr_svc = 0;
+	set_bit(SPI_INTR, &qca->intr);
 	qca->sync = QCASPI_SYNC_UNKNOWN;
 	qcafrm_fsm_init_spi(&qca->frm_handle);
 
@@ -812,7 +829,6 @@
 
 	dev->mtu = QCAFRM_MAX_MTU;
 	dev->type = ARPHRD_ETHER;
-	qca->clkspeed = qcaspi_clkspeed;
 	qca->burst_len = qcaspi_burst_len;
 	qca->spi_thread = NULL;
 	qca->buffer_size = (dev->mtu + VLAN_ETH_HLEN + QCAFRM_HEADER_LEN +
@@ -901,17 +917,15 @@
 	legacy_mode = of_property_read_bool(spi->dev.of_node,
 					    "qca,legacy-mode");
 
-	if (qcaspi_clkspeed == 0) {
-		if (spi->max_speed_hz)
-			qcaspi_clkspeed = spi->max_speed_hz;
-		else
-			qcaspi_clkspeed = QCASPI_CLK_SPEED;
-	}
-
-	if ((qcaspi_clkspeed < QCASPI_CLK_SPEED_MIN) ||
-	    (qcaspi_clkspeed > QCASPI_CLK_SPEED_MAX)) {
-		dev_err(&spi->dev, "Invalid clkspeed: %d\n",
-			qcaspi_clkspeed);
+	if (qcaspi_clkspeed)
+		spi->max_speed_hz = qcaspi_clkspeed;
+	else if (!spi->max_speed_hz)
+		spi->max_speed_hz = QCASPI_CLK_SPEED;
+
+	if (spi->max_speed_hz < QCASPI_CLK_SPEED_MIN ||
+	    spi->max_speed_hz > QCASPI_CLK_SPEED_MAX) {
+		dev_err(&spi->dev, "Invalid clkspeed: %u\n",
+			spi->max_speed_hz);
 		return -EINVAL;
 	}
 
@@ -936,14 +950,13 @@
 		return -EINVAL;
 	}
 
-	dev_info(&spi->dev, "ver=%s, clkspeed=%d, burst_len=%d, pluggable=%d\n",
+	dev_info(&spi->dev, "ver=%s, clkspeed=%u, burst_len=%d, pluggable=%d\n",
 		 QCASPI_DRV_VERSION,
-		 qcaspi_clkspeed,
+		 spi->max_speed_hz,
 		 qcaspi_burst_len,
 		 qcaspi_pluggable);
 
 	spi->mode = SPI_MODE_3;
-	spi->max_speed_hz = qcaspi_clkspeed;
 	if (spi_setup(spi) < 0) {
 		dev_err(&spi->dev, "Unable to setup SPI device\n");
 		return -EFAULT;
@@ -968,7 +981,7 @@
 
 	spi_set_drvdata(spi, qcaspi_devs);
 
-	ret = of_get_mac_address(spi->dev.of_node, qca->net_dev->dev_addr);
+	ret = of_get_ethdev_address(spi->dev.of_node, qca->net_dev);
 	if (ret) {
 		eth_hw_addr_random(qca->net_dev);
 		dev_info(&spi->dev, "Using random MAC address: %pM\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/qca_spi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/qca_spi.h
@@ -93,8 +93,7 @@
 	struct qcafrm_handle frm_handle;
 	struct sk_buff *rx_skb;
 
-	unsigned int intr_req;
-	unsigned int intr_svc;
+	unsigned long intr;
 	u16 reset_count;
 
 #ifdef CONFIG_DEBUG_FS
@@ -102,7 +101,6 @@
 #endif
 
 	/* user configurable options */
-	u32 clkspeed;
 	u8 legacy_mode;
 	u16 burst_len;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/qca_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/qca_uart.c
@@ -347,7 +347,7 @@
 
 	of_property_read_u32(serdev->dev.of_node, "current-speed", &speed);
 
-	ret = of_get_mac_address(serdev->dev.of_node, qca->net_dev->dev_addr);
+	ret = of_get_ethdev_address(serdev->dev.of_node, qca->net_dev);
 	if (ret) {
 		eth_hw_addr_random(qca->net_dev);
 		dev_info(&serdev->dev, "Using random MAC address: %pM\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c
@@ -391,7 +391,7 @@
 
 struct rtnl_link_ops rmnet_link_ops __read_mostly = {
 	.kind		= "rmnet",
-	.maxtype	= __IFLA_RMNET_MAX,
+	.maxtype	= IFLA_RMNET_MAX,
 	.priv_size	= sizeof(struct rmnet_priv),
 	.setup		= rmnet_vnd_setup,
 	.validate	= rmnet_rtnl_validate,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/rdc/r6040.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/rdc/r6040.c
@@ -453,7 +453,7 @@
 {
 	struct r6040_private *lp = netdev_priv(dev);
 	void __iomem *ioaddr = lp->base;
-	u16 *adrp;
+	const u16 *adrp;
 
 	/* Stop MAC */
 	iowrite16(MSK_INT, ioaddr + MIER);	/* Mask Off Interrupt */
@@ -462,7 +462,7 @@
 	r6040_reset_mac(lp);
 
 	/* Restore MAC Address to MIDx */
-	adrp = (u16 *) dev->dev_addr;
+	adrp = (const u16 *) dev->dev_addr;
 	iowrite16(adrp[0], ioaddr + MID_0L);
 	iowrite16(adrp[1], ioaddr + MID_0M);
 	iowrite16(adrp[2], ioaddr + MID_0H);
@@ -731,13 +731,13 @@
 {
 	struct r6040_private *lp = netdev_priv(dev);
 	void __iomem *ioaddr = lp->base;
-	u16 *adrp;
+	const u16 *adrp;
 
 	/* Reset MAC */
 	r6040_reset_mac(lp);
 
 	/* Restore MAC Address */
-	adrp = (u16 *) dev->dev_addr;
+	adrp = (const u16 *) dev->dev_addr;
 	iowrite16(adrp[0], ioaddr + MID_0L);
 	iowrite16(adrp[1], ioaddr + MID_0M);
 	iowrite16(adrp[2], ioaddr + MID_0H);
@@ -849,13 +849,13 @@
 	unsigned long flags;
 	struct netdev_hw_addr *ha;
 	int i;
-	u16 *adrp;
+	const u16 *adrp;
 	u16 hash_table[4] = { 0 };
 
 	spin_lock_irqsave(&lp->lock, flags);
 
 	/* Keep our MAC Address */
-	adrp = (u16 *)dev->dev_addr;
+	adrp = (const u16 *)dev->dev_addr;
 	iowrite16(adrp[0], ioaddr + MID_0L);
 	iowrite16(adrp[1], ioaddr + MID_0M);
 	iowrite16(adrp[2], ioaddr + MID_0H);
@@ -1159,10 +1159,12 @@
 	err = register_netdev(dev);
 	if (err) {
 		dev_err(&pdev->dev, "Failed to register net device\n");
-		goto err_out_mdio_unregister;
+		goto err_out_phy_disconnect;
 	}
 	return 0;
 
+err_out_phy_disconnect:
+	phy_disconnect(dev->phydev);
 err_out_mdio_unregister:
 	mdiobus_unregister(lp->mii_bus);
 err_out_mdio:
@@ -1186,6 +1188,7 @@
 	struct r6040_private *lp = netdev_priv(dev);
 
 	unregister_netdev(dev);
+	phy_disconnect(dev->phydev);
 	mdiobus_unregister(lp->mii_bus);
 	mdiobus_free(lp->mii_bus);
 	netif_napi_del(&lp->napi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/realtek/r8169_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/realtek/r8169_main.c
@@ -205,6 +205,7 @@
 					/* No threshold before first PCI xfer */
 #define	RX_FIFO_THRESH			(7 << RXCFG_FIFO_SHIFT)
 #define	RX_EARLY_OFF			(1 << 11)
+#define	RX_PAUSE_SLOT_ON		(1 << 11)	/* 8125b and later */
 #define	RXCFG_DMA_SHIFT			8
 					/* Unlimited maximum PCI burst. */
 #define	RX_DMA_BURST			(7 << RXCFG_DMA_SHIFT)
@@ -574,7 +575,34 @@
 	__le64	rx_broadcast;
 	__le32	rx_multicast;
 	__le16	tx_aborted;
-	__le16	tx_underun;
+	__le16	tx_underrun;
+	/* new since RTL8125 */
+	__le64 tx_octets;
+	__le64 rx_octets;
+	__le64 rx_multicast64;
+	__le64 tx_unicast64;
+	__le64 tx_broadcast64;
+	__le64 tx_multicast64;
+	__le32 tx_pause_on;
+	__le32 tx_pause_off;
+	__le32 tx_pause_all;
+	__le32 tx_deferred;
+	__le32 tx_late_collision;
+	__le32 tx_all_collision;
+	__le32 tx_aborted32;
+	__le32 align_errors32;
+	__le32 rx_frame_too_long;
+	__le32 rx_runt;
+	__le32 rx_pause_on;
+	__le32 rx_pause_off;
+	__le32 rx_pause_all;
+	__le32 rx_unknown_opcode;
+	__le32 rx_mac_error;
+	__le32 tx_underrun32;
+	__le32 rx_mac_missed;
+	__le32 rx_tcam_dropped;
+	__le32 tdu;
+	__le32 rdu;
 };
 
 struct rtl8169_tc_offsets {
@@ -588,6 +616,8 @@
 enum rtl_flag {
 	RTL_FLAG_TASK_ENABLED = 0,
 	RTL_FLAG_TASK_RESET_PENDING,
+	RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE,
+	RTL_FLAG_TASK_TX_TIMEOUT,
 	RTL_FLAG_MAX
 };
 
@@ -624,7 +654,11 @@
 	} wk;
 
 	unsigned supports_gmii:1;
-	unsigned aspm_manageable:1;
+	unsigned rtl_aspm_enabled:1;
+	struct delayed_work aspm_toggle;
+	atomic_t aspm_packet_count;
+	struct mutex config_lock;
+
 	dma_addr_t counters_phys_addr;
 	struct rtl8169_counters *counters;
 	struct rtl8169_tc_offsets tc_offset;
@@ -673,12 +707,14 @@
 
 static void rtl_lock_config_regs(struct rtl8169_private *tp)
 {
+	mutex_lock(&tp->config_lock);
 	RTL_W8(tp, Cfg9346, Cfg9346_Lock);
 }
 
 static void rtl_unlock_config_regs(struct rtl8169_private *tp)
 {
 	RTL_W8(tp, Cfg9346, Cfg9346_Unlock);
+	mutex_unlock(&tp->config_lock);
 }
 
 static void rtl_pci_commit(struct rtl8169_private *tp)
@@ -1188,7 +1224,7 @@
 {
 	r8168ep_ocp_write(tp, 0x01, 0x180, OOB_CMD_DRIVER_START);
 	r8168ep_ocp_write(tp, 0x01, 0x30, r8168ep_ocp_read(tp, 0x30) | 0x01);
-	rtl_loop_wait_high(tp, &rtl_ep_ocp_read_cond, 10000, 10);
+	rtl_loop_wait_high(tp, &rtl_ep_ocp_read_cond, 10000, 30);
 }
 
 static void rtl8168_driver_start(struct rtl8169_private *tp)
@@ -1663,7 +1699,7 @@
 	data[9] = le64_to_cpu(counters->rx_broadcast);
 	data[10] = le32_to_cpu(counters->rx_multicast);
 	data[11] = le16_to_cpu(counters->tx_aborted);
-	data[12] = le16_to_cpu(counters->tx_underun);
+	data[12] = le16_to_cpu(counters->tx_underrun);
 }
 
 static void rtl8169_get_strings(struct net_device *dev, u32 stringset, u8 *data)
@@ -2251,28 +2287,6 @@
 	return 0;
 }
 
-static void rtl_wol_enable_rx(struct rtl8169_private *tp)
-{
-	if (tp->mac_version >= RTL_GIGA_MAC_VER_25)
-		RTL_W32(tp, RxConfig, RTL_R32(tp, RxConfig) |
-			AcceptBroadcast | AcceptMulticast | AcceptMyPhys);
-}
-
-static void rtl_prepare_power_down(struct rtl8169_private *tp)
-{
-	if (tp->dash_type != RTL_DASH_NONE)
-		return;
-
-	if (tp->mac_version == RTL_GIGA_MAC_VER_32 ||
-	    tp->mac_version == RTL_GIGA_MAC_VER_33)
-		rtl_ephy_write(tp, 0x19, 0xff64);
-
-	if (device_may_wakeup(tp_to_dev(tp))) {
-		phy_speed_down(tp->phydev, false);
-		rtl_wol_enable_rx(tp);
-	}
-}
-
 static void rtl_init_rxcfg(struct rtl8169_private *tp)
 {
 	switch (tp->mac_version) {
@@ -2288,9 +2302,13 @@
 	case RTL_GIGA_MAC_VER_40 ... RTL_GIGA_MAC_VER_53:
 		RTL_W32(tp, RxConfig, RX128_INT_EN | RX_MULTI_EN | RX_DMA_BURST | RX_EARLY_OFF);
 		break;
-	case RTL_GIGA_MAC_VER_60 ... RTL_GIGA_MAC_VER_63:
+	case RTL_GIGA_MAC_VER_61:
 		RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST);
 		break;
+	case RTL_GIGA_MAC_VER_63:
+		RTL_W32(tp, RxConfig, RX_FETCH_DFLT_8125 | RX_DMA_BURST |
+			RX_PAUSE_SLOT_ON);
+		break;
 	default:
 		RTL_W32(tp, RxConfig, RX128_INT_EN | RX_DMA_BURST);
 		break;
@@ -2492,6 +2510,28 @@
 	rtl_wait_txrx_fifo_empty(tp);
 }
 
+static void rtl_wol_enable_rx(struct rtl8169_private *tp)
+{
+	if (tp->mac_version >= RTL_GIGA_MAC_VER_25)
+		RTL_W32(tp, RxConfig, RTL_R32(tp, RxConfig) |
+			AcceptBroadcast | AcceptMulticast | AcceptMyPhys);
+}
+
+static void rtl_prepare_power_down(struct rtl8169_private *tp)
+{
+	if (tp->dash_type != RTL_DASH_NONE)
+		return;
+
+	if (tp->mac_version == RTL_GIGA_MAC_VER_32 ||
+	    tp->mac_version == RTL_GIGA_MAC_VER_33)
+		rtl_ephy_write(tp, 0x19, 0xff64);
+
+	if (device_may_wakeup(tp_to_dev(tp))) {
+		phy_speed_down(tp->phydev, false);
+		rtl_wol_enable_rx(tp);
+	}
+}
+
 static void rtl_set_tx_config_registers(struct rtl8169_private *tp)
 {
 	u32 val = TX_DMA_BURST << TxDMAShift |
@@ -2549,6 +2589,8 @@
 
 	if (dev->flags & IFF_PROMISC) {
 		rx_mode |= AcceptAllPhys;
+	} else if (!(dev->flags & IFF_MULTICAST)) {
+		rx_mode &= ~AcceptMulticast;
 	} else if (netdev_mc_count(dev) > MC_FILTER_LIMIT ||
 		   dev->flags & IFF_ALLMULTI ||
 		   tp->mac_version == RTL_GIGA_MAC_VER_35) {
@@ -2700,8 +2742,15 @@
 
 static void rtl_hw_aspm_clkreq_enable(struct rtl8169_private *tp, bool enable)
 {
-	/* Don't enable ASPM in the chip if OS can't control ASPM */
-	if (enable && tp->aspm_manageable) {
+	struct pci_dev *pdev = tp->pci_dev;
+
+	/* Skip if PCIe ASPM isn't possible */
+	if (!pcie_aspm_support_enabled() || !pcie_aspm_capable(pdev))
+		return;
+
+	tp->rtl_aspm_enabled = enable;
+
+	if (enable) {
 		RTL_W8(tp, Config5, RTL_R8(tp, Config5) | ASPM_en);
 		RTL_W8(tp, Config2, RTL_R8(tp, Config2) | ClkReqEn);
 	} else {
@@ -3518,6 +3567,7 @@
 	rtl_eri_write(tp, 0x1b0, ERIAR_MASK_0011, 0x0000);
 
 	rtl_pcie_state_l2l3_disable(tp);
+	rtl_hw_aspm_clkreq_enable(tp, true);
 }
 
 static void rtl_hw_start_8106(struct rtl8169_private *tp)
@@ -4027,7 +4077,7 @@
 {
 	struct rtl8169_private *tp = netdev_priv(dev);
 
-	rtl_schedule_task(tp, RTL_FLAG_TASK_RESET_PENDING);
+	rtl_schedule_task(tp, RTL_FLAG_TASK_TX_TIMEOUT);
 }
 
 static int rtl8169_tx_map(struct rtl8169_private *tp, const u32 *opts, u32 len,
@@ -4112,8 +4162,8 @@
 {
 	unsigned int padto = 0, len = skb->len;
 
-	if (rtl_is_8125(tp) && len < 128 + RTL_MIN_PATCH_LEN &&
-	    rtl_skb_is_udp(skb) && skb_transport_header_was_set(skb)) {
+	if (len < 128 + RTL_MIN_PATCH_LEN && rtl_skb_is_udp(skb) &&
+	    skb_transport_header_was_set(skb)) {
 		unsigned int trans_data_len = skb_tail_pointer(skb) -
 					      skb_transport_header(skb);
 
@@ -4137,9 +4187,15 @@
 static unsigned int rtl_quirk_packet_padto(struct rtl8169_private *tp,
 					   struct sk_buff *skb)
 {
-	unsigned int padto;
+	unsigned int padto = 0;
 
-	padto = rtl8125_quirk_udp_padto(tp, skb);
+	switch (tp->mac_version) {
+	case RTL_GIGA_MAC_VER_61 ... RTL_GIGA_MAC_VER_63:
+		padto = rtl8125_quirk_udp_padto(tp, skb);
+		break;
+	default:
+		break;
+	}
 
 	switch (tp->mac_version) {
 	case RTL_GIGA_MAC_VER_34:
@@ -4177,7 +4233,6 @@
 static bool rtl8169_tso_csum_v2(struct rtl8169_private *tp,
 				struct sk_buff *skb, u32 *opts)
 {
-	u32 transport_offset = (u32)skb_transport_offset(skb);
 	struct skb_shared_info *shinfo = skb_shinfo(skb);
 	u32 mss = shinfo->gso_size;
 
@@ -4194,7 +4249,7 @@
 			WARN_ON_ONCE(1);
 		}
 
-		opts[0] |= transport_offset << GTTCPHO_SHIFT;
+		opts[0] |= skb_transport_offset(skb) << GTTCPHO_SHIFT;
 		opts[1] |= mss << TD1_MSS_SHIFT;
 	} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
 		u8 ip_protocol;
@@ -4222,7 +4277,7 @@
 		else
 			WARN_ON_ONCE(1);
 
-		opts[1] |= transport_offset << TCPHO_SHIFT;
+		opts[1] |= skb_transport_offset(skb) << TCPHO_SHIFT;
 	} else {
 		unsigned int padto = rtl_quirk_packet_padto(tp, skb);
 
@@ -4265,17 +4320,18 @@
 static netdev_tx_t rtl8169_start_xmit(struct sk_buff *skb,
 				      struct net_device *dev)
 {
-	unsigned int frags = skb_shinfo(skb)->nr_frags;
 	struct rtl8169_private *tp = netdev_priv(dev);
 	unsigned int entry = tp->cur_tx % NUM_TX_DESC;
 	struct TxDesc *txd_first, *txd_last;
 	bool stop_queue, door_bell;
+	unsigned int frags;
 	u32 opts[2];
 
 	if (unlikely(!rtl_tx_slots_avail(tp))) {
 		if (net_ratelimit())
 			netdev_err(dev, "BUG! Tx Ring full when queue awake!\n");
-		goto err_stop_0;
+		netif_stop_queue(dev);
+		return NETDEV_TX_BUSY;
 	}
 
 	opts[1] = rtl8169_tx_vlan_tag(skb);
@@ -4292,6 +4348,7 @@
 
 	txd_first = tp->TxDescArray + entry;
 
+	frags = skb_shinfo(skb)->nr_frags;
 	if (frags) {
 		if (rtl8169_xmit_frags(tp, skb, opts, entry))
 			goto err_dma_1;
@@ -4347,11 +4404,6 @@
 	dev_kfree_skb_any(skb);
 	dev->stats.tx_dropped++;
 	return NETDEV_TX_OK;
-
-err_stop_0:
-	netif_stop_queue(dev);
-	dev->stats.tx_dropped++;
-	return NETDEV_TX_BUSY;
 }
 
 static unsigned int rtl_last_frag_len(struct sk_buff *skb)
@@ -4389,14 +4441,13 @@
 						struct net_device *dev,
 						netdev_features_t features)
 {
-	int transport_offset = skb_transport_offset(skb);
 	struct rtl8169_private *tp = netdev_priv(dev);
 
 	if (skb_is_gso(skb)) {
 		if (tp->mac_version == RTL_GIGA_MAC_VER_34)
 			features = rtl8168evl_fix_tso(skb, features);
 
-		if (transport_offset > GTTCPHO_MAX &&
+		if (skb_transport_offset(skb) > GTTCPHO_MAX &&
 		    rtl_chip_supports_csum_v2(tp))
 			features &= ~NETIF_F_ALL_TSO;
 	} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
@@ -4407,7 +4458,7 @@
 		if (rtl_quirk_packet_padto(tp, skb))
 			features &= ~NETIF_F_CSUM_MASK;
 
-		if (transport_offset > TCPHO_MAX &&
+		if (skb_transport_offset(skb) > TCPHO_MAX &&
 		    rtl_chip_supports_csum_v2(tp))
 			features &= ~NETIF_F_CSUM_MASK;
 	}
@@ -4441,11 +4492,12 @@
 
 	dirty_tx = tp->dirty_tx;
 
+	atomic_add(tp->cur_tx - dirty_tx, &tp->aspm_packet_count);
 	while (READ_ONCE(tp->cur_tx) != dirty_tx) {
 		unsigned int entry = dirty_tx % NUM_TX_DESC;
 		u32 status;
 
-		status = le32_to_cpu(tp->TxDescArray[entry].opts1);
+		status = le32_to_cpu(READ_ONCE(tp->TxDescArray[entry].opts1));
 		if (status & DescOwn)
 			break;
 
@@ -4482,7 +4534,7 @@
 		 * If skb is NULL then we come here again once a tx irq is
 		 * triggered after the last fragment is marked transmitted.
 		 */
-		if (tp->cur_tx != dirty_tx && skb)
+		if (READ_ONCE(tp->cur_tx) != dirty_tx && skb)
 			rtl8169_doorbell(tp);
 	}
 }
@@ -4515,7 +4567,7 @@
 		dma_addr_t addr;
 		u32 status;
 
-		status = le32_to_cpu(desc->opts1);
+		status = le32_to_cpu(READ_ONCE(desc->opts1));
 		if (status & DescOwn)
 			break;
 
@@ -4585,6 +4637,8 @@
 		rtl8169_mark_to_asic(desc);
 	}
 
+	atomic_add(count, &tp->aspm_packet_count);
+
 	return count;
 }
 
@@ -4596,7 +4650,9 @@
 	if ((status & 0xffff) == 0xffff || !(status & tp->irq_mask))
 		return IRQ_NONE;
 
-	if (unlikely(status & SYSErr)) {
+	/* At least RTL8168fp may unexpectedly set the SYSErr bit */
+	if (unlikely(status & SYSErr &&
+	    tp->mac_version <= RTL_GIGA_MAC_VER_06)) {
 		rtl8169_pcierr_interrupt(tp->dev);
 		goto out;
 	}
@@ -4610,10 +4666,8 @@
 		rtl_schedule_task(tp, RTL_FLAG_TASK_RESET_PENDING);
 	}
 
-	if (napi_schedule_prep(&tp->napi)) {
-		rtl_irq_disable(tp);
-		__napi_schedule(&tp->napi);
-	}
+	rtl_irq_disable(tp);
+	napi_schedule(&tp->napi);
 out:
 	rtl_ack_events(tp, status);
 
@@ -4624,6 +4678,7 @@
 {
 	struct rtl8169_private *tp =
 		container_of(work, struct rtl8169_private, wk.work);
+	int ret;
 
 	rtnl_lock();
 
@@ -4631,9 +4686,21 @@
 	    !test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
 		goto out_unlock;
 
+	if (test_and_clear_bit(RTL_FLAG_TASK_TX_TIMEOUT, tp->wk.flags)) {
+		/* ASPM compatibility issues are a typical reason for tx timeouts */
+		ret = pci_disable_link_state(tp->pci_dev, PCIE_LINK_STATE_L1 |
+							  PCIE_LINK_STATE_L0S);
+		if (!ret)
+			netdev_warn_once(tp->dev, "ASPM disabled on Tx timeout\n");
+		goto reset;
+	}
+
 	if (test_and_clear_bit(RTL_FLAG_TASK_RESET_PENDING, tp->wk.flags)) {
+reset:
 		rtl_reset_work(tp);
 		netif_wake_queue(tp->dev);
+	} else if (test_and_clear_bit(RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE, tp->wk.flags)) {
+		rtl_reset_work(tp);
 	}
 out_unlock:
 	rtnl_unlock();
@@ -4658,12 +4725,17 @@
 static void r8169_phylink_handler(struct net_device *ndev)
 {
 	struct rtl8169_private *tp = netdev_priv(ndev);
+	struct device *d = tp_to_dev(tp);
 
 	if (netif_carrier_ok(ndev)) {
 		rtl_link_chg_patch(tp);
-		pm_request_resume(&tp->pci_dev->dev);
+		pm_request_resume(d);
+		netif_wake_queue(tp->dev);
 	} else {
-		pm_runtime_idle(&tp->pci_dev->dev);
+		/* In few cases rx is broken after link-down otherwise */
+		if (rtl_is_8125(tp))
+			rtl_schedule_task(tp, RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE);
+		pm_runtime_idle(d);
 	}
 
 	if (net_ratelimit())
@@ -4692,8 +4764,39 @@
 	return 0;
 }
 
+#define ASPM_PACKET_THRESHOLD 10
+#define ASPM_TOGGLE_INTERVAL 1000
+
+static void rtl8169_aspm_toggle(struct work_struct *work)
+{
+	struct rtl8169_private *tp = container_of(work, struct rtl8169_private,
+						  aspm_toggle.work);
+	int packet_count;
+	bool enable;
+
+	packet_count = atomic_xchg(&tp->aspm_packet_count, 0);
+
+	if (pcie_aspm_enabled(tp->pci_dev)) {
+		enable = packet_count <= ASPM_PACKET_THRESHOLD;
+
+		if (tp->rtl_aspm_enabled != enable) {
+			rtl_unlock_config_regs(tp);
+			rtl_hw_aspm_clkreq_enable(tp, enable);
+			rtl_lock_config_regs(tp);
+		}
+	} else if (tp->rtl_aspm_enabled) {
+		rtl_unlock_config_regs(tp);
+		rtl_hw_aspm_clkreq_enable(tp, false);
+		rtl_lock_config_regs(tp);
+	}
+
+	schedule_delayed_work(&tp->aspm_toggle, msecs_to_jiffies(ASPM_TOGGLE_INTERVAL));
+}
+
 static void rtl8169_down(struct rtl8169_private *tp)
 {
+	cancel_delayed_work_sync(&tp->aspm_toggle);
+
 	/* Clear all task flags */
 	bitmap_zero(tp->wk.flags, RTL_FLAG_MAX);
 
@@ -4707,10 +4810,16 @@
 	rtl8169_cleanup(tp, true);
 
 	rtl_prepare_power_down(tp);
+
+	if (tp->dash_type != RTL_DASH_NONE)
+		rtl8168_driver_stop(tp);
 }
 
 static void rtl8169_up(struct rtl8169_private *tp)
 {
+	if (tp->dash_type != RTL_DASH_NONE)
+		rtl8168_driver_start(tp);
+
 	pci_set_master(tp->pci_dev);
 	phy_init_hw(tp->phydev);
 	phy_resume(tp->phydev);
@@ -4720,6 +4829,10 @@
 	rtl_reset_work(tp);
 
 	phy_start(tp->phydev);
+
+	/* pcie_aspm_capable may change after system resume */
+	if (pcie_aspm_support_enabled() && pcie_aspm_capable(tp->pci_dev))
+		schedule_delayed_work(&tp->aspm_toggle, 0);
 }
 
 static int rtl8169_close(struct net_device *dev)
@@ -4733,7 +4846,7 @@
 	rtl8169_down(tp);
 	rtl8169_rx_clear(tp);
 
-	cancel_work_sync(&tp->wk.work);
+	cancel_work(&tp->wk.work);
 
 	free_irq(pci_irq_vector(pdev, 0), tp);
 
@@ -4866,8 +4979,6 @@
 		rtl8169_down(tp);
 }
 
-#ifdef CONFIG_PM
-
 static int rtl8169_runtime_resume(struct device *dev)
 {
 	struct rtl8169_private *tp = dev_get_drvdata(dev);
@@ -4883,7 +4994,7 @@
 	return 0;
 }
 
-static int __maybe_unused rtl8169_suspend(struct device *device)
+static int rtl8169_suspend(struct device *device)
 {
 	struct rtl8169_private *tp = dev_get_drvdata(device);
 
@@ -4896,7 +5007,7 @@
 	return 0;
 }
 
-static int __maybe_unused rtl8169_resume(struct device *device)
+static int rtl8169_resume(struct device *device)
 {
 	struct rtl8169_private *tp = dev_get_drvdata(device);
 
@@ -4938,13 +5049,11 @@
 }
 
 static const struct dev_pm_ops rtl8169_pm_ops = {
-	SET_SYSTEM_SLEEP_PM_OPS(rtl8169_suspend, rtl8169_resume)
-	SET_RUNTIME_PM_OPS(rtl8169_runtime_suspend, rtl8169_runtime_resume,
-			   rtl8169_runtime_idle)
+	SYSTEM_SLEEP_PM_OPS(rtl8169_suspend, rtl8169_resume)
+	RUNTIME_PM_OPS(rtl8169_runtime_suspend, rtl8169_runtime_resume,
+		       rtl8169_runtime_idle)
 };
 
-#endif /* CONFIG_PM */
-
 static void rtl_wol_shutdown_quirk(struct rtl8169_private *tp)
 {
 	/* WoL fails with 8168b when the receiver is disabled. */
@@ -4989,6 +5098,8 @@
 	if (pci_dev_run_wake(pdev))
 		pm_runtime_get_noresume(&pdev->dev);
 
+	cancel_work_sync(&tp->wk.work);
+
 	unregister_netdev(tp->dev);
 
 	if (tp->dash_type != RTL_DASH_NONE)
@@ -5109,6 +5220,15 @@
 	struct mii_bus *new_bus;
 	int ret;
 
+	/* On some boards with this chip version the BIOS is buggy and misses
+	 * to reset the PHY page selector. This results in the PHY ID read
+	 * accessing registers on a different page, returning a more or
+	 * less random value. Fix this by resetting the page selector first.
+	 */
+	if (tp->mac_version == RTL_GIGA_MAC_VER_25 ||
+	    tp->mac_version == RTL_GIGA_MAC_VER_26)
+		r8169_mdio_write(tp, 0x1f, 0);
+
 	new_bus = devm_mdiobus_alloc(&pdev->dev);
 	if (!new_bus)
 		return -ENOMEM;
@@ -5139,7 +5259,7 @@
 		return -EUNATCH;
 	}
 
-	tp->phydev->mac_managed_pm = 1;
+	tp->phydev->mac_managed_pm = true;
 
 	phy_support_asym_pause(tp->phydev);
 
@@ -5307,12 +5427,6 @@
 	if (rc)
 		return rc;
 
-	/* Disable ASPM L1 as that cause random device stop working
-	 * problems as well as full system hangs for some PCIe devices users.
-	 */
-	rc = pci_disable_link_state(pdev, PCIE_LINK_STATE_L1);
-	tp->aspm_manageable = !rc;
-
 	/* enable device (incl. PCI PM wakeup and hotplug setup) */
 	rc = pcim_enable_device(pdev);
 	if (rc < 0) {
@@ -5342,6 +5456,8 @@
 		return rc;
 	}
 
+	mutex_init(&tp->config_lock);
+
 	tp->mmio_addr = pcim_iomap_table(pdev)[region];
 
 	xid = (RTL_R32(tp, TxConfig) >> 20) & 0xfcf;
@@ -5379,6 +5495,10 @@
 
 	INIT_WORK(&tp->wk.work, rtl_task);
 
+	INIT_DELAYED_WORK(&tp->aspm_toggle, rtl8169_aspm_toggle);
+
+	atomic_set(&tp->aspm_packet_count, 0);
+
 	rtl_init_mac_address(tp);
 
 	dev->ethtool_ops = &rtl8169_ethtool_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/realtek/r8169_phy_config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/realtek/r8169_phy_config.c
@@ -970,6 +970,9 @@
 	/* disable phy pfm mode */
 	phy_modify_paged(phydev, 0x0a44, 0x11, BIT(7), 0);
 
+	/* disable 10m pll off */
+	phy_modify_paged(phydev, 0x0a43, 0x10, BIT(0), 0);
+
 	rtl8168g_disable_aldps(phydev);
 	rtl8168g_config_eee_phy(phydev);
 }
@@ -1260,6 +1263,7 @@
 	phy_modify_paged(phydev, 0xa86, 0x15, 0x0001, 0x0000);
 	rtl8168g_enable_gphy_10m(phydev);
 
+	rtl8168g_disable_aldps(phydev);
 	rtl8125a_config_eee_phy(phydev);
 }
 
@@ -1299,6 +1303,7 @@
 	phy_modify_paged(phydev, 0xbf8, 0x12, 0xe000, 0xa000);
 
 	rtl8125_legacy_force_mode(phydev);
+	rtl8168g_disable_aldps(phydev);
 	rtl8125b_config_eee_phy(phydev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/renesas/ravb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/renesas/ravb.h
@@ -1000,8 +1000,8 @@
 	unsigned internal_delay:1;	/* AVB-DMAC has internal delays */
 	unsigned tx_counters:1;		/* E-MAC has TX counters */
 	unsigned multi_irqs:1;		/* AVB-DMAC and E-MAC has multiple irqs */
-	unsigned no_ptp_cfg_active:1;	/* AVB-DMAC does not support gPTP active in config mode */
-	unsigned ptp_cfg_active:1;	/* AVB-DMAC has gPTP support active in config mode */
+	unsigned gptp:1;		/* AVB-DMAC has gPTP support */
+	unsigned ccc_gac:1;		/* AVB-DMAC has gPTP support active in config mode */
 };
 
 struct ravb_private {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/renesas/ravb_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/renesas/ravb_main.c
@@ -30,8 +30,7 @@
 #include <linux/spinlock.h>
 #include <linux/sys_soc.h>
 #include <linux/reset.h>
-
-#include <asm/div64.h>
+#include <linux/math64.h>
 
 #include "ravb.h"
 
@@ -115,7 +114,7 @@
 {
 	int ret;
 
-	ret = of_get_mac_address(np, ndev->dev_addr);
+	ret = of_get_ethdev_address(np, ndev);
 	if (ret) {
 		u32 mahr = ravb_read(ndev, MAHR);
 		u32 malr = ravb_read(ndev, MALR);
@@ -793,14 +792,14 @@
 	ravb_write(ndev, ~(EIS_QFS | EIS_RESERVED), EIS);
 	if (eis & EIS_QFS) {
 		ris2 = ravb_read(ndev, RIS2);
-		ravb_write(ndev, ~(RIS2_QFF0 | RIS2_RFFF | RIS2_RESERVED),
+		ravb_write(ndev, ~(RIS2_QFF0 | RIS2_QFF1 | RIS2_RFFF | RIS2_RESERVED),
 			   RIS2);
 
 		/* Receive Descriptor Empty int */
 		if (ris2 & RIS2_QFF0)
 			priv->stats[RAVB_BE].rx_over_errors++;
 
-		    /* Receive Descriptor Empty int */
+		/* Receive Descriptor Empty int */
 		if (ris2 & RIS2_QFF1)
 			priv->stats[RAVB_NC].rx_over_errors++;
 
@@ -970,12 +969,12 @@
 	int q = napi - priv->napi;
 	int mask = BIT(q);
 	int quota = budget;
+	bool unmask;
 
 	/* Processing RX Descriptor Ring */
 	/* Clear RX interrupt */
 	ravb_write(ndev, ~(mask | RIS0_RESERVED), RIS0);
-	if (ravb_rx(ndev, &quota, q))
-		goto out;
+	unmask = !ravb_rx(ndev, &quota, q);
 
 	/* Processing TX Descriptor Ring */
 	spin_lock_irqsave(&priv->lock, flags);
@@ -985,6 +984,9 @@
 	netif_wake_subqueue(ndev, q);
 	spin_unlock_irqrestore(&priv->lock, flags);
 
+	if (!unmask)
+		goto out;
+
 	napi_complete(napi);
 
 	/* Re-enable RX/TX interrupts */
@@ -1274,7 +1276,7 @@
 	if (netif_running(ndev)) {
 		netif_device_detach(ndev);
 		/* Stop PTP Clock driver */
-		if (info->no_ptp_cfg_active)
+		if (info->gptp)
 			ravb_ptp_stop(ndev);
 		/* Wait for DMA stopping */
 		error = ravb_stop_dma(ndev);
@@ -1306,7 +1308,7 @@
 		ravb_emac_init(ndev);
 
 		/* Initialise PTP Clock driver */
-		if (info->no_ptp_cfg_active)
+		if (info->gptp)
 			ravb_ptp_init(ndev, priv->pdev);
 
 		netif_device_attach(ndev);
@@ -1446,22 +1448,23 @@
 	ravb_emac_init(ndev);
 
 	/* Initialise PTP Clock driver */
-	if (info->no_ptp_cfg_active)
+	if (info->gptp)
 		ravb_ptp_init(ndev, priv->pdev);
 
-	netif_tx_start_all_queues(ndev);
-
 	/* PHY control start */
 	error = ravb_phy_start(ndev);
 	if (error)
 		goto out_ptp_stop;
 
+	netif_tx_start_all_queues(ndev);
+
 	return 0;
 
 out_ptp_stop:
 	/* Stop PTP Clock driver */
-	if (info->no_ptp_cfg_active)
+	if (info->gptp)
 		ravb_ptp_stop(ndev);
+	ravb_stop_dma(ndev);
 out_free_irq_nc_tx:
 	if (!info->multi_irqs)
 		goto out_free_irq;
@@ -1505,10 +1508,16 @@
 	struct net_device *ndev = priv->ndev;
 	int error;
 
+	if (!rtnl_trylock()) {
+		usleep_range(1000, 2000);
+		schedule_work(&priv->work);
+		return;
+	}
+
 	netif_tx_stop_all_queues(ndev);
 
 	/* Stop PTP Clock driver */
-	if (info->no_ptp_cfg_active)
+	if (info->gptp)
 		ravb_ptp_stop(ndev);
 
 	/* Wait for DMA stopping */
@@ -1537,16 +1546,19 @@
 		 */
 		netdev_err(ndev, "%s: ravb_dmac_init() failed, error %d\n",
 			   __func__, error);
-		return;
+		goto out_unlock;
 	}
 	ravb_emac_init(ndev);
 
 out:
 	/* Initialise PTP Clock driver */
-	if (info->no_ptp_cfg_active)
+	if (info->gptp)
 		ravb_ptp_init(ndev, priv->pdev);
 
 	netif_tx_start_all_queues(ndev);
+
+out_unlock:
+	rtnl_unlock();
 }
 
 /* Packet transmit function for Ethernet AVB */
@@ -1558,7 +1570,7 @@
 	struct ravb_tstamp_skb *ts_skb;
 	struct ravb_tx_desc *desc;
 	unsigned long flags;
-	u32 dma_addr;
+	dma_addr_t dma_addr;
 	void *buffer;
 	u32 entry;
 	u32 len;
@@ -1752,7 +1764,7 @@
 	ravb_write(ndev, 0, TIC);
 
 	/* Stop PTP Clock driver */
-	if (info->no_ptp_cfg_active)
+	if (info->gptp)
 		ravb_ptp_stop(ndev);
 
 	/* Set the config mode to stop the AVB-DMAC's processes */
@@ -1775,6 +1787,8 @@
 			of_phy_deregister_fixed_link(np);
 	}
 
+	cancel_work_sync(&priv->work);
+
 	if (info->multi_irqs) {
 		free_irq(priv->tx_irqs[RAVB_NC], ndev);
 		free_irq(priv->rx_irqs[RAVB_NC], ndev);
@@ -1960,6 +1974,8 @@
 {
 	struct platform_device *pdev = priv->pdev;
 	struct device *dev = &pdev->dev;
+	struct phy_device *phydev;
+	struct device_node *pn;
 	int error;
 
 	/* Bitbang init */
@@ -1981,6 +1997,14 @@
 	if (error)
 		goto out_free_bus;
 
+	pn = of_parse_phandle(dev->of_node, "phy-handle", 0);
+	phydev = of_phy_find_device(pn);
+	if (phydev) {
+		phydev->mac_managed_pm = true;
+		put_device(&phydev->mdio.dev);
+	}
+	of_node_put(pn);
+
 	return 0;
 
 out_free_bus:
@@ -2018,7 +2042,7 @@
 	.internal_delay = 1,
 	.tx_counters = 1,
 	.multi_irqs = 1,
-	.ptp_cfg_active = 1,
+	.ccc_gac = 1,
 };
 
 static const struct ravb_hw_info ravb_gen2_hw_info = {
@@ -2037,7 +2061,7 @@
 	.stats_len = ARRAY_SIZE(ravb_gstrings_stats),
 	.max_rx_len = RX_BUF_SZ + RAVB_ALIGN - 1,
 	.aligned_tx = 1,
-	.no_ptp_cfg_active = 1,
+	.gptp = 1,
 };
 
 static const struct of_device_id ravb_match_table[] = {
@@ -2046,6 +2070,7 @@
 	{ .compatible = "renesas,etheravb-rcar-gen2", .data = &ravb_gen2_hw_info },
 	{ .compatible = "renesas,etheravb-r8a7795", .data = &ravb_gen3_hw_info },
 	{ .compatible = "renesas,etheravb-rcar-gen3", .data = &ravb_gen3_hw_info },
+	{ .compatible = "renesas,etheravb-rcar-gen4", .data = &ravb_gen3_hw_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, ravb_match_table);
@@ -2061,8 +2086,7 @@
 	if (!rate)
 		return -EINVAL;
 
-	inc = 1000000000ULL << 20;
-	do_div(inc, rate);
+	inc = div64_ul(1000000000ULL << 20, rate);
 
 	if (inc < GTI_TIV_MIN || inc > GTI_TIV_MAX) {
 		dev_err(dev, "gti.tiv increment 0x%llx is outside the range 0x%x - 0x%x\n",
@@ -2080,7 +2104,7 @@
 	struct ravb_private *priv = netdev_priv(ndev);
 	const struct ravb_hw_info *info = priv->info;
 
-	if (info->no_ptp_cfg_active) {
+	if (info->gptp) {
 		ravb_modify(ndev, CCC, CCC_OPC, CCC_OPC_CONFIG);
 		/* Set CSEL value */
 		ravb_modify(ndev, CCC, CCC_CSEL, CCC_CSEL_HPB);
@@ -2169,9 +2193,14 @@
 	ndev->features = info->net_features;
 	ndev->hw_features = info->net_hw_features;
 
-	reset_control_deassert(rstc);
+	error = reset_control_deassert(rstc);
+	if (error)
+		goto out_free_netdev;
+
 	pm_runtime_enable(&pdev->dev);
-	pm_runtime_get_sync(&pdev->dev);
+	error = pm_runtime_resume_and_get(&pdev->dev);
+	if (error < 0)
+		goto out_rpm_disable;
 
 	if (info->multi_irqs)
 		irq = platform_get_irq_byname(pdev, "ch22");
@@ -2301,7 +2330,7 @@
 	INIT_LIST_HEAD(&priv->ts_skb_list);
 
 	/* Initialise PTP Clock driver */
-	if (info->ptp_cfg_active)
+	if (info->ccc_gac)
 		ravb_ptp_init(ndev, pdev);
 
 	/* Debug message level */
@@ -2349,16 +2378,17 @@
 			  priv->desc_bat_dma);
 
 	/* Stop PTP Clock driver */
-	if (info->ptp_cfg_active)
+	if (info->ccc_gac)
 		ravb_ptp_stop(ndev);
 out_disable_refclk:
 	clk_disable_unprepare(priv->refclk);
 out_release:
-	free_netdev(ndev);
-
 	pm_runtime_put(&pdev->dev);
+out_rpm_disable:
 	pm_runtime_disable(&pdev->dev);
 	reset_control_assert(rstc);
+out_free_netdev:
+	free_netdev(ndev);
 	return error;
 }
 
@@ -2369,20 +2399,20 @@
 	const struct ravb_hw_info *info = priv->info;
 
 	/* Stop PTP Clock driver */
-	if (info->ptp_cfg_active)
+	if (info->ccc_gac)
 		ravb_ptp_stop(ndev);
 
 	clk_disable_unprepare(priv->refclk);
 
-	dma_free_coherent(ndev->dev.parent, priv->desc_bat_size, priv->desc_bat,
-			  priv->desc_bat_dma);
 	/* Set reset mode */
 	ravb_write(ndev, CCC_OPC_RESET, CCC);
-	pm_runtime_put_sync(&pdev->dev);
 	unregister_netdev(ndev);
 	netif_napi_del(&priv->napi[RAVB_NC]);
 	netif_napi_del(&priv->napi[RAVB_BE]);
 	ravb_mdio_release(priv);
+	dma_free_coherent(ndev->dev.parent, priv->desc_bat_size, priv->desc_bat,
+			  priv->desc_bat_dma);
+	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	reset_control_assert(priv->rstc);
 	free_netdev(ndev);
@@ -2446,6 +2476,9 @@
 	else
 		ret = ravb_close(ndev);
 
+	if (priv->info->ccc_gac)
+		ravb_ptp_stop(ndev);
+
 	return ret;
 }
 
@@ -2482,6 +2515,9 @@
 	/* Restore descriptor base address table */
 	ravb_write(ndev, priv->desc_bat_dma, DBAT);
 
+	if (priv->info->ccc_gac)
+		ravb_ptp_init(ndev, priv->pdev);
+
 	if (netif_running(ndev)) {
 		if (priv->wol_enabled) {
 			ret = ravb_wol_restore(ndev);
@@ -2491,6 +2527,7 @@
 		ret = ravb_open(ndev);
 		if (ret < 0)
 			return ret;
+		ravb_set_rx_mode(ndev);
 		netif_device_attach(ndev);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/renesas/sh_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/renesas/sh_eth.c
@@ -3072,6 +3072,8 @@
 	struct bb_info *bitbang;
 	struct platform_device *pdev = mdp->pdev;
 	struct device *dev = &mdp->pdev->dev;
+	struct phy_device *phydev;
+	struct device_node *pn;
 
 	/* create bit control struct for PHY */
 	bitbang = devm_kzalloc(dev, sizeof(struct bb_info), GFP_KERNEL);
@@ -3106,6 +3108,14 @@
 	if (ret)
 		goto out_free_bus;
 
+	pn = of_parse_phandle(dev->of_node, "phy-handle", 0);
+	phydev = of_phy_find_device(pn);
+	if (phydev) {
+		phydev->mac_managed_pm = true;
+		put_device(&phydev->mdio.dev);
+	}
+	of_node_put(pn);
+
 	return 0;
 
 out_free_bus:
@@ -3466,10 +3476,12 @@
 
 	netif_device_detach(ndev);
 
+	rtnl_lock();
 	if (mdp->wol_enabled)
 		ret = sh_eth_wol_setup(ndev);
 	else
 		ret = sh_eth_close(ndev);
+	rtnl_unlock();
 
 	return ret;
 }
@@ -3483,10 +3495,12 @@
 	if (!netif_running(ndev))
 		return 0;
 
+	rtnl_lock();
 	if (mdp->wol_enabled)
 		ret = sh_eth_wol_restore(ndev);
 	else
 		ret = sh_eth_open(ndev);
+	rtnl_unlock();
 
 	if (ret < 0)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/rocker/rocker_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/rocker/rocker_main.c
@@ -2516,7 +2516,7 @@
 	u64 link_status = rocker_read64(rocker, PORT_PHYS_LINK_STATUS);
 	bool link_up;
 
-	link_up = link_status & (1 << rocker_port->pport);
+	link_up = link_status & (1ULL << rocker_port->pport);
 	if (link_up)
 		netif_carrier_on(rocker_port->dev);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/rocker/rocker_ofdpa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/rocker/rocker_ofdpa.c
@@ -1273,7 +1273,7 @@
 	bool removing;
 	int err = 0;
 
-	entry = kzalloc(sizeof(*entry), GFP_KERNEL);
+	entry = kzalloc(sizeof(*entry), GFP_ATOMIC);
 	if (!entry)
 		return -ENOMEM;
 
@@ -2783,7 +2783,8 @@
 		if (!ofdpa_port)
 			continue;
 		nh->fib_nh_flags &= ~RTNH_F_OFFLOAD;
-		ofdpa_flow_tbl_del(ofdpa_port, OFDPA_OP_FLAG_REMOVE,
+		ofdpa_flow_tbl_del(ofdpa_port,
+				   OFDPA_OP_FLAG_REMOVE | OFDPA_OP_FLAG_NOWAIT,
 				   flow_entry);
 	}
 	spin_unlock_irqrestore(&ofdpa->flow_tbl_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/samsung/sxgbe/sxgbe_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/samsung/sxgbe/sxgbe_common.h
@@ -329,7 +329,7 @@
 	/* Set power management mode (e.g. magic frame) */
 	void (*pmt)(void __iomem *ioaddr, unsigned long mode);
 	/* Set/Get Unicast MAC addresses */
-	void (*set_umac_addr)(void __iomem *ioaddr, unsigned char *addr,
+	void (*set_umac_addr)(void __iomem *ioaddr, const unsigned char *addr,
 			      unsigned int reg_n);
 	void (*get_umac_addr)(void __iomem *ioaddr, unsigned char *addr,
 			      unsigned int reg_n);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/samsung/sxgbe/sxgbe_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/samsung/sxgbe/sxgbe_core.c
@@ -85,7 +85,8 @@
 }
 
 /* Set/Get Unicast MAC addresses */
-static void sxgbe_core_set_umac_addr(void __iomem *ioaddr, unsigned char *addr,
+static void sxgbe_core_set_umac_addr(void __iomem *ioaddr,
+				     const unsigned char *addr,
 				     unsigned int reg_n)
 {
 	u32 high_word, low_word;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
@@ -2282,18 +2282,18 @@
 	char *opt;
 
 	if (!str || !*str)
-		return -EINVAL;
+		return 1;
 	while ((opt = strsep(&str, ",")) != NULL) {
 		if (!strncmp(opt, "eee_timer:", 10)) {
 			if (kstrtoint(opt + 10, 0, &eee_timer))
 				goto err;
 		}
 	}
-	return 0;
+	return 1;
 
 err:
 	pr_err("%s: ERROR broken module parameter conversion\n", __func__);
-	return -EINVAL;
+	return 1;
 }
 
 __setup("sxgbeeth=", sxgbe_cmdline_opt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c
@@ -118,7 +118,7 @@
 	}
 
 	/* Get MAC address if available (DT) */
-	of_get_mac_address(node, priv->dev->dev_addr);
+	of_get_ethdev_address(node, priv->dev);
 
 	/* Get the TX/RX IRQ numbers */
 	for (i = 0, chan = 1; i < SXGBE_TX_QUEUES; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/seeq/ether3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/seeq/ether3.c
@@ -845,9 +845,11 @@
 {
 	struct net_device *dev = ecard_get_drvdata(ec);
 
+	ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
 	ecard_set_drvdata(ec, NULL);
 
 	unregister_netdev(dev);
+	del_timer_sync(&priv(dev)->timer);
 	free_netdev(dev);
 	ecard_release_resources(ec);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ef10.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ef10.c
@@ -1038,7 +1038,7 @@
 }
 
 int efx_ef10_vport_add_mac(struct efx_nic *efx,
-			   unsigned int port_id, u8 *mac)
+			   unsigned int port_id, const u8 *mac)
 {
 	MCDI_DECLARE_BUF(inbuf, MC_CMD_VPORT_ADD_MAC_ADDRESS_IN_LEN);
 
@@ -1050,7 +1050,7 @@
 }
 
 int efx_ef10_vport_del_mac(struct efx_nic *efx,
-			   unsigned int port_id, u8 *mac)
+			   unsigned int port_id, const u8 *mac)
 {
 	MCDI_DECLARE_BUF(inbuf, MC_CMD_VPORT_DEL_MAC_ADDRESS_IN_LEN);
 
@@ -1297,14 +1297,17 @@
 {
 	struct efx_ef10_nic_data *nic_data = efx->nic_data;
 
+	spin_lock_bh(&efx->stats_lock);
 	kfree(nic_data->mc_stats);
 	nic_data->mc_stats = NULL;
+	spin_unlock_bh(&efx->stats_lock);
 }
 
 static int efx_ef10_init_nic(struct efx_nic *efx)
 {
 	struct efx_ef10_nic_data *nic_data = efx->nic_data;
-	netdev_features_t hw_enc_features = 0;
+	struct net_device *net_dev = efx->net_dev;
+	netdev_features_t tun_feats, tso_feats;
 	int rc;
 
 	if (nic_data->must_check_datapath_caps) {
@@ -1349,20 +1352,30 @@
 		nic_data->must_restore_piobufs = false;
 	}
 
-	/* add encapsulated checksum offload features */
+	/* encap features might change during reset if fw variant changed */
 	if (efx_has_cap(efx, VXLAN_NVGRE) && !efx_ef10_is_vf(efx))
-		hw_enc_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
-	/* add encapsulated TSO features */
-	if (efx_has_cap(efx, TX_TSO_V2_ENCAP)) {
-		netdev_features_t encap_tso_features;
+		net_dev->hw_enc_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+	else
+		net_dev->hw_enc_features &= ~(NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM);
 
-		encap_tso_features = NETIF_F_GSO_UDP_TUNNEL | NETIF_F_GSO_GRE |
-			NETIF_F_GSO_UDP_TUNNEL_CSUM | NETIF_F_GSO_GRE_CSUM;
+	tun_feats = NETIF_F_GSO_UDP_TUNNEL | NETIF_F_GSO_GRE |
+		    NETIF_F_GSO_UDP_TUNNEL_CSUM | NETIF_F_GSO_GRE_CSUM;
+	tso_feats = NETIF_F_TSO | NETIF_F_TSO6;
 
-		hw_enc_features |= encap_tso_features | NETIF_F_TSO;
-		efx->net_dev->features |= encap_tso_features;
+	if (efx_has_cap(efx, TX_TSO_V2_ENCAP)) {
+		/* If this is first nic_init, or if it is a reset and a new fw
+		 * variant has added new features, enable them by default.
+		 * If the features are not new, maintain their current value.
+		 */
+		if (!(net_dev->hw_features & tun_feats))
+			net_dev->features |= tun_feats;
+		net_dev->hw_enc_features |= tun_feats | tso_feats;
+		net_dev->hw_features |= tun_feats;
+	} else {
+		net_dev->hw_enc_features &= ~(tun_feats | tso_feats);
+		net_dev->hw_features &= ~tun_feats;
+		net_dev->features &= ~tun_feats;
 	}
-	efx->net_dev->hw_enc_features = hw_enc_features;
 
 	/* don't fail init if RSS setup doesn't work */
 	rc = efx->type->rx_push_rss_config(efx, false,
@@ -1841,9 +1854,14 @@
 
 	efx_ef10_get_stat_mask(efx, mask);
 
-	efx_nic_copy_stats(efx, nic_data->mc_stats);
-	efx_nic_update_stats(efx_ef10_stat_desc, EF10_STAT_COUNT,
-			     mask, stats, nic_data->mc_stats, false);
+	/* If NIC was fini'd (probably resetting), then we can't read
+	 * updated stats right now.
+	 */
+	if (nic_data->mc_stats) {
+		efx_nic_copy_stats(efx, nic_data->mc_stats);
+		efx_nic_update_stats(efx_ef10_stat_desc, EF10_STAT_COUNT,
+				     mask, stats, nic_data->mc_stats, false);
+	}
 
 	/* Update derived statistics */
 	efx_nic_fix_nodesc_drop_stat(efx,
@@ -1932,7 +1950,10 @@
 
 	efx_update_sw_stats(efx, stats);
 out:
+	/* releasing a DMA coherent buffer with BH disabled can panic */
+	spin_unlock_bh(&efx->stats_lock);
 	efx_nic_free_buffer(efx, &stats_buf);
+	spin_lock_bh(&efx->stats_lock);
 	return rc;
 }
 
@@ -2256,7 +2277,7 @@
 	 * guaranteed to satisfy the second as we only attempt TSO if
 	 * inner_network_header <= 208.
 	 */
-	ip_tot_len = -EFX_TSO2_MAX_HDRLEN;
+	ip_tot_len = 0x10000 - EFX_TSO2_MAX_HDRLEN;
 	EFX_WARN_ON_ONCE_PARANOID(mss + EFX_TSO2_MAX_HDRLEN +
 				  (tcp->doff << 2u) > ip_tot_len);
 
@@ -3268,6 +3289,30 @@
 	bool was_enabled = efx->port_enabled;
 	int rc;
 
+#ifdef CONFIG_SFC_SRIOV
+	/* If this function is a VF and we have access to the parent PF,
+	 * then use the PF control path to attempt to change the VF MAC address.
+	 */
+	if (efx->pci_dev->is_virtfn && efx->pci_dev->physfn) {
+		struct efx_nic *efx_pf = pci_get_drvdata(efx->pci_dev->physfn);
+		struct efx_ef10_nic_data *nic_data = efx->nic_data;
+		u8 mac[ETH_ALEN];
+
+		/* net_dev->dev_addr can be zeroed by efx_net_stop in
+		 * efx_ef10_sriov_set_vf_mac, so pass in a copy.
+		 */
+		ether_addr_copy(mac, efx->net_dev->dev_addr);
+
+		rc = efx_ef10_sriov_set_vf_mac(efx_pf, nic_data->vf_index, mac);
+		if (!rc)
+			return 0;
+
+		netif_dbg(efx, drv, efx->net_dev,
+			  "Updating VF mac via PF failed (%d), setting directly\n",
+			  rc);
+	}
+#endif
+
 	efx_device_detach_sync(efx);
 	efx_net_stop(efx->net_dev);
 
@@ -3290,40 +3335,6 @@
 		efx_net_open(efx->net_dev);
 	efx_device_attach_if_not_resetting(efx);
 
-#ifdef CONFIG_SFC_SRIOV
-	if (efx->pci_dev->is_virtfn && efx->pci_dev->physfn) {
-		struct efx_ef10_nic_data *nic_data = efx->nic_data;
-		struct pci_dev *pci_dev_pf = efx->pci_dev->physfn;
-
-		if (rc == -EPERM) {
-			struct efx_nic *efx_pf;
-
-			/* Switch to PF and change MAC address on vport */
-			efx_pf = pci_get_drvdata(pci_dev_pf);
-
-			rc = efx_ef10_sriov_set_vf_mac(efx_pf,
-						       nic_data->vf_index,
-						       efx->net_dev->dev_addr);
-		} else if (!rc) {
-			struct efx_nic *efx_pf = pci_get_drvdata(pci_dev_pf);
-			struct efx_ef10_nic_data *nic_data = efx_pf->nic_data;
-			unsigned int i;
-
-			/* MAC address successfully changed by VF (with MAC
-			 * spoofing) so update the parent PF if possible.
-			 */
-			for (i = 0; i < efx_pf->vf_count; ++i) {
-				struct ef10_vf *vf = nic_data->vf + i;
-
-				if (vf->efx == efx) {
-					ether_addr_copy(vf->mac,
-							efx->net_dev->dev_addr);
-					return 0;
-				}
-			}
-		}
-	} else
-#endif
 	if (rc == -EPERM) {
 		netif_err(efx, drv, efx->net_dev,
 			  "Cannot change MAC address; use sfboot to enable"
@@ -3579,6 +3590,11 @@
 		n_parts++;
 	}
 
+	if (!n_parts) {
+		kfree(parts);
+		return 0;
+	}
+
 	rc = efx_mtd_add(efx, &parts[0].common, n_parts, sizeof(*parts));
 fail:
 	if (rc)
@@ -3990,12 +4006,39 @@
 	}
 }
 
+static unsigned int efx_ef10_recycle_ring_size(const struct efx_nic *efx)
+{
+	unsigned int ret = EFX_RECYCLE_RING_SIZE_10G;
+
+	/* There is no difference between PFs and VFs. The side is based on
+	 * the maximum link speed of a given NIC.
+	 */
+	switch (efx->pci_dev->device & 0xfff) {
+	case 0x0903:	/* Farmingdale can do up to 10G */
+		break;
+	case 0x0923:	/* Greenport can do up to 40G */
+	case 0x0a03:	/* Medford can do up to 40G */
+		ret *= 4;
+		break;
+	default:	/* Medford2 can do up to 100G */
+		ret *= 10;
+	}
+
+	if (IS_ENABLED(CONFIG_PPC64))
+		ret *= 4;
+
+	return ret;
+}
+
 #define EF10_OFFLOAD_FEATURES		\
 	(NETIF_F_IP_CSUM |		\
 	 NETIF_F_HW_VLAN_CTAG_FILTER |	\
 	 NETIF_F_IPV6_CSUM |		\
 	 NETIF_F_RXHASH |		\
-	 NETIF_F_NTUPLE)
+	 NETIF_F_NTUPLE |		\
+	 NETIF_F_SG |			\
+	 NETIF_F_RXCSUM |		\
+	 NETIF_F_RXALL)
 
 const struct efx_nic_type efx_hunt_a0_vf_nic_type = {
 	.is_vf = true,
@@ -4106,6 +4149,7 @@
 	.check_caps = ef10_check_caps,
 	.print_additional_fwver = efx_ef10_print_additional_fwver,
 	.sensor_event = efx_mcdi_sensor_event,
+	.rx_recycle_ring_size = efx_ef10_recycle_ring_size,
 };
 
 const struct efx_nic_type efx_hunt_a0_nic_type = {
@@ -4243,4 +4287,5 @@
 	.check_caps = ef10_check_caps,
 	.print_additional_fwver = efx_ef10_print_additional_fwver,
 	.sensor_event = efx_mcdi_sensor_event,
+	.rx_recycle_ring_size = efx_ef10_recycle_ring_size,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ef100_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ef100_netdev.c
@@ -96,6 +96,8 @@
 	efx_mcdi_free_vis(efx);
 	efx_remove_interrupts(efx);
 
+	efx->state = STATE_NET_DOWN;
+
 	return 0;
 }
 
@@ -172,6 +174,8 @@
 		efx_link_status_changed(efx);
 	mutex_unlock(&efx->mac_lock);
 
+	efx->state = STATE_NET_UP;
+
 	return 0;
 
 fail:
@@ -200,6 +204,7 @@
 		   skb->len, skb->data_len, channel->channel);
 	if (!efx->n_channels || !efx->n_tx_channels || !channel) {
 		netif_stop_queue(net_dev);
+		dev_kfree_skb_any(skb);
 		goto err;
 	}
 
@@ -271,7 +276,7 @@
 	/* Always start with carrier off; PHY events will detect the link */
 	netif_carrier_off(net_dev);
 
-	efx->state = STATE_READY;
+	efx->state = STATE_NET_DOWN;
 	rtnl_unlock();
 	efx_init_mcdi_logging(efx);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ef100_nic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ef100_nic.c
@@ -23,6 +23,7 @@
 #include "ef100_rx.h"
 #include "ef100_tx.h"
 #include "ef100_netdev.h"
+#include "rx_common.h"
 
 #define EF100_MAX_VIS 4096
 #define EF100_NUM_MCDI_BUFFERS	1
@@ -609,6 +610,9 @@
 	ef100_common_stat_mask(mask);
 	ef100_ethtool_stat_mask(mask);
 
+	if (!mc_stats)
+		return 0;
+
 	efx_nic_copy_stats(efx, mc_stats);
 	efx_nic_update_stats(ef100_stat_desc, EF100_STAT_COUNT, mask,
 			     stats, mc_stats, false);
@@ -693,6 +697,12 @@
 	}
 }
 
+static unsigned int efx_ef100_recycle_ring_size(const struct efx_nic *efx)
+{
+	/* Maximum link speed for Riverhead is 100G */
+	return 10 * EFX_RECYCLE_RING_SIZE_10G;
+}
+
 /*	NIC level access functions
  */
 #define EF100_OFFLOAD_FEATURES	(NETIF_F_HW_CSUM | NETIF_F_RXCSUM |	\
@@ -767,6 +777,7 @@
 	.rx_push_rss_context_config = efx_mcdi_rx_push_rss_context_config,
 	.rx_pull_rss_context_config = efx_mcdi_rx_pull_rss_context_config,
 	.rx_restore_rss_contexts = efx_mcdi_rx_restore_rss_contexts,
+	.rx_recycle_ring_size = efx_ef100_recycle_ring_size,
 
 	.reconfigure_mac = ef100_reconfigure_mac,
 	.reconfigure_port = efx_mcdi_port_reconfigure,
@@ -846,6 +857,7 @@
 	.rx_pull_rss_config = efx_mcdi_rx_pull_rss_config,
 	.rx_push_rss_config = efx_mcdi_pf_rx_push_rss_config,
 	.rx_restore_rss_contexts = efx_mcdi_rx_restore_rss_contexts,
+	.rx_recycle_ring_size = efx_ef100_recycle_ring_size,
 
 	.reconfigure_mac = ef100_reconfigure_mac,
 	.test_nvram = efx_new_mcdi_nvram_test_all,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ef100_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ef100_tx.c
@@ -349,7 +349,8 @@
  * Returns 0 on success, error code otherwise. In case of an error this
  * function will free the SKB.
  */
-int ef100_enqueue_skb(struct efx_tx_queue *tx_queue, struct sk_buff *skb)
+netdev_tx_t ef100_enqueue_skb(struct efx_tx_queue *tx_queue,
+			      struct sk_buff *skb)
 {
 	unsigned int old_insert_count = tx_queue->insert_count;
 	struct efx_nic *efx = tx_queue->efx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ef10_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ef10_sriov.c
@@ -408,8 +408,9 @@
 static int efx_ef10_pci_sriov_disable(struct efx_nic *efx, bool force)
 {
 	struct pci_dev *dev = efx->pci_dev;
+	struct efx_ef10_nic_data *nic_data = efx->nic_data;
 	unsigned int vfs_assigned = pci_vfs_assigned(dev);
-	int rc = 0;
+	int i, rc = 0;
 
 	if (vfs_assigned && !force) {
 		netif_info(efx, drv, efx->net_dev, "VFs are assigned to guests; "
@@ -417,10 +418,13 @@
 		return -EBUSY;
 	}
 
-	if (!vfs_assigned)
+	if (!vfs_assigned) {
+		for (i = 0; i < efx->vf_count; i++)
+			nic_data->vf[i].pci_dev = NULL;
 		pci_disable_sriov(dev);
-	else
+	} else {
 		rc = -EBUSY;
+	}
 
 	efx_ef10_sriov_free_vf_vswitching(efx);
 	efx->vf_count = 0;
@@ -480,7 +484,7 @@
 	return rc;
 }
 
-int efx_ef10_sriov_set_vf_mac(struct efx_nic *efx, int vf_i, u8 *mac)
+int efx_ef10_sriov_set_vf_mac(struct efx_nic *efx, int vf_i, const u8 *mac)
 {
 	struct efx_ef10_nic_data *nic_data = efx->nic_data;
 	struct ef10_vf *vf;
@@ -523,7 +527,7 @@
 			goto fail;
 
 		if (vf->efx)
-			ether_addr_copy(vf->efx->net_dev->dev_addr, mac);
+			eth_hw_addr_set(vf->efx->net_dev, mac);
 	}
 
 	ether_addr_copy(vf->mac, mac);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ef10_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ef10_sriov.h
@@ -39,7 +39,7 @@
 void efx_ef10_sriov_fini(struct efx_nic *efx);
 static inline void efx_ef10_sriov_flr(struct efx_nic *efx, unsigned vf_i) {}
 
-int efx_ef10_sriov_set_vf_mac(struct efx_nic *efx, int vf, u8 *mac);
+int efx_ef10_sriov_set_vf_mac(struct efx_nic *efx, int vf, const u8 *mac);
 
 int efx_ef10_sriov_set_vf_vlan(struct efx_nic *efx, int vf_i,
 			       u16 vlan, u8 qos);
@@ -60,9 +60,9 @@
 void efx_ef10_vswitching_remove_pf(struct efx_nic *efx);
 void efx_ef10_vswitching_remove_vf(struct efx_nic *efx);
 int efx_ef10_vport_add_mac(struct efx_nic *efx,
-			   unsigned int port_id, u8 *mac);
+			   unsigned int port_id, const u8 *mac);
 int efx_ef10_vport_del_mac(struct efx_nic *efx,
-			   unsigned int port_id, u8 *mac);
+			   unsigned int port_id, const u8 *mac);
 int efx_ef10_vadaptor_alloc(struct efx_nic *efx, unsigned int port_id);
 int efx_ef10_vadaptor_query(struct efx_nic *efx, unsigned int port_id,
 			    u32 *port_flags, u32 *vadaptor_flags,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/efx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/efx.c
@@ -105,14 +105,6 @@
 static int efx_xdp_xmit(struct net_device *dev, int n, struct xdp_frame **xdpfs,
 			u32 flags);
 
-#define EFX_ASSERT_RESET_SERIALISED(efx)		\
-	do {						\
-		if ((efx->state == STATE_READY) ||	\
-		    (efx->state == STATE_RECOVERY) ||	\
-		    (efx->state == STATE_DISABLED))	\
-			ASSERT_RTNL();			\
-	} while (0)
-
 /**************************************************************************
  *
  * Port handling
@@ -136,7 +128,7 @@
 		return rc;
 
 	/* Initialise MAC address to permanent address */
-	ether_addr_copy(efx->net_dev->dev_addr, efx->net_dev->perm_addr);
+	eth_hw_addr_set(efx->net_dev, efx->net_dev->perm_addr);
 
 	return 0;
 }
@@ -377,6 +369,8 @@
 	if (rc)
 		goto fail5;
 
+	efx->state = STATE_NET_DOWN;
+
 	return 0;
 
  fail5:
@@ -543,7 +537,9 @@
 	efx_start_all(efx);
 	if (efx->state == STATE_DISABLED || efx->reset_pending)
 		netif_device_detach(efx->net_dev);
-	efx_selftest_async_start(efx);
+	else
+		efx->state = STATE_NET_UP;
+
 	return 0;
 }
 
@@ -719,8 +715,6 @@
 	 * already requested.  If so, the NIC is probably hosed so we
 	 * abort.
 	 */
-	efx->state = STATE_READY;
-	smp_mb(); /* ensure we change state before checking reset_pending */
 	if (efx->reset_pending) {
 		pci_err(efx->pci_dev, "aborting probe due to scheduled reset\n");
 		rc = -EIO;
@@ -747,6 +741,8 @@
 
 	efx_associate(efx);
 
+	efx->state = STATE_NET_DOWN;
+
 	rtnl_unlock();
 
 	rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_type);
@@ -848,7 +844,7 @@
 	/* Flush reset_work. It can no longer be scheduled since we
 	 * are not READY.
 	 */
-	BUG_ON(efx->state == STATE_READY);
+	WARN_ON(efx_net_active(efx->state));
 	efx_flush_reset_workqueue(efx);
 
 	efx_disable_interrupts(efx);
@@ -1003,18 +999,18 @@
 	}
 
 	/* Determine netdevice features */
-	net_dev->features |= (efx->type->offload_features | NETIF_F_SG |
-			      NETIF_F_TSO | NETIF_F_RXCSUM | NETIF_F_RXALL);
-	if (efx->type->offload_features & (NETIF_F_IPV6_CSUM | NETIF_F_HW_CSUM))
-		net_dev->features |= NETIF_F_TSO6;
-	/* Check whether device supports TSO */
-	if (!efx->type->tso_versions || !efx->type->tso_versions(efx))
-		net_dev->features &= ~NETIF_F_ALL_TSO;
+	net_dev->features |= efx->type->offload_features;
+
+	/* Add TSO features */
+	if (efx->type->tso_versions && efx->type->tso_versions(efx))
+		net_dev->features |= NETIF_F_TSO | NETIF_F_TSO6;
+
 	/* Mask for features that also apply to VLAN devices */
 	net_dev->vlan_features |= (NETIF_F_HW_CSUM | NETIF_F_SG |
 				   NETIF_F_HIGHDMA | NETIF_F_ALL_TSO |
 				   NETIF_F_RXCSUM);
 
+	/* Determine user configurable features */
 	net_dev->hw_features |= net_dev->features & ~efx->fixed_features;
 
 	/* Disable receiving frames with bad FCS, by default. */
@@ -1153,13 +1149,13 @@
 
 	rtnl_lock();
 
-	if (efx->state != STATE_DISABLED) {
-		efx->state = STATE_UNINIT;
-
+	if (efx_net_active(efx->state)) {
 		efx_device_detach_sync(efx);
 
 		efx_stop_all(efx);
 		efx_disable_interrupts(efx);
+
+		efx->state = efx_freeze(efx->state);
 	}
 
 	rtnl_unlock();
@@ -1174,7 +1170,7 @@
 
 	rtnl_lock();
 
-	if (efx->state != STATE_DISABLED) {
+	if (efx_frozen(efx->state)) {
 		rc = efx_enable_interrupts(efx);
 		if (rc)
 			goto fail;
@@ -1187,7 +1183,7 @@
 
 		efx_device_attach_if_not_resetting(efx);
 
-		efx->state = STATE_READY;
+		efx->state = efx_thaw(efx->state);
 
 		efx->type->resume_wol(efx);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/efx_channels.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/efx_channels.c
@@ -308,6 +308,7 @@
 		efx->n_channels = 1;
 		efx->n_rx_channels = 1;
 		efx->n_tx_channels = 1;
+		efx->tx_channel_offset = 0;
 		efx->n_xdp_channels = 0;
 		efx->xdp_channel_offset = efx->n_channels;
 		rc = pci_enable_msi(efx->pci_dev);
@@ -328,6 +329,7 @@
 		efx->n_channels = 1 + (efx_separate_tx_channels ? 1 : 0);
 		efx->n_rx_channels = 1;
 		efx->n_tx_channels = 1;
+		efx->tx_channel_offset = efx_separate_tx_channels ? 1 : 0;
 		efx->n_xdp_channels = 0;
 		efx->xdp_channel_offset = efx->n_channels;
 		efx->legacy_irq = efx->pci_dev->irq;
@@ -763,9 +765,90 @@
 	kfree(efx->xdp_tx_queues);
 }
 
+static int efx_set_xdp_tx_queue(struct efx_nic *efx, int xdp_queue_number,
+				struct efx_tx_queue *tx_queue)
+{
+	if (xdp_queue_number >= efx->xdp_tx_queue_count)
+		return -EINVAL;
+
+	netif_dbg(efx, drv, efx->net_dev,
+		  "Channel %u TXQ %u is XDP %u, HW %u\n",
+		  tx_queue->channel->channel, tx_queue->label,
+		  xdp_queue_number, tx_queue->queue);
+	efx->xdp_tx_queues[xdp_queue_number] = tx_queue;
+	return 0;
+}
+
+static void efx_set_xdp_channels(struct efx_nic *efx)
+{
+	struct efx_tx_queue *tx_queue;
+	struct efx_channel *channel;
+	unsigned int next_queue = 0;
+	int xdp_queue_number = 0;
+	int rc;
+
+	/* We need to mark which channels really have RX and TX
+	 * queues, and adjust the TX queue numbers if we have separate
+	 * RX-only and TX-only channels.
+	 */
+	efx_for_each_channel(channel, efx) {
+		if (channel->channel < efx->tx_channel_offset)
+			continue;
+
+		if (efx_channel_is_xdp_tx(channel)) {
+			efx_for_each_channel_tx_queue(tx_queue, channel) {
+				tx_queue->queue = next_queue++;
+				rc = efx_set_xdp_tx_queue(efx, xdp_queue_number,
+							  tx_queue);
+				if (rc == 0)
+					xdp_queue_number++;
+			}
+		} else {
+			efx_for_each_channel_tx_queue(tx_queue, channel) {
+				tx_queue->queue = next_queue++;
+				netif_dbg(efx, drv, efx->net_dev,
+					  "Channel %u TXQ %u is HW %u\n",
+					  channel->channel, tx_queue->label,
+					  tx_queue->queue);
+			}
+
+			/* If XDP is borrowing queues from net stack, it must
+			 * use the queue with no csum offload, which is the
+			 * first one of the channel
+			 * (note: tx_queue_by_type is not initialized yet)
+			 */
+			if (efx->xdp_txq_queues_mode ==
+			    EFX_XDP_TX_QUEUES_BORROWED) {
+				tx_queue = &channel->tx_queue[0];
+				rc = efx_set_xdp_tx_queue(efx, xdp_queue_number,
+							  tx_queue);
+				if (rc == 0)
+					xdp_queue_number++;
+			}
+		}
+	}
+	WARN_ON(efx->xdp_txq_queues_mode == EFX_XDP_TX_QUEUES_DEDICATED &&
+		xdp_queue_number != efx->xdp_tx_queue_count);
+	WARN_ON(efx->xdp_txq_queues_mode != EFX_XDP_TX_QUEUES_DEDICATED &&
+		xdp_queue_number > efx->xdp_tx_queue_count);
+
+	/* If we have more CPUs than assigned XDP TX queues, assign the already
+	 * existing queues to the exceeding CPUs
+	 */
+	next_queue = 0;
+	while (xdp_queue_number < efx->xdp_tx_queue_count) {
+		tx_queue = efx->xdp_tx_queues[next_queue++];
+		rc = efx_set_xdp_tx_queue(efx, xdp_queue_number, tx_queue);
+		if (rc == 0)
+			xdp_queue_number++;
+	}
+}
+
 int efx_realloc_channels(struct efx_nic *efx, u32 rxq_entries, u32 txq_entries)
 {
-	struct efx_channel *other_channel[EFX_MAX_CHANNELS], *channel;
+	struct efx_channel *other_channel[EFX_MAX_CHANNELS], *channel,
+			   *ptp_channel = efx_ptp_channel(efx);
+	struct efx_ptp_data *ptp_data = efx->ptp_data;
 	unsigned int i, next_buffer_table = 0;
 	u32 old_rxq_entries, old_txq_entries;
 	int rc, rc2;
@@ -818,11 +901,8 @@
 	old_txq_entries = efx->txq_entries;
 	efx->rxq_entries = rxq_entries;
 	efx->txq_entries = txq_entries;
-	for (i = 0; i < efx->n_channels; i++) {
-		channel = efx->channel[i];
-		efx->channel[i] = other_channel[i];
-		other_channel[i] = channel;
-	}
+	for (i = 0; i < efx->n_channels; i++)
+		swap(efx->channel[i], other_channel[i]);
 
 	/* Restart buffer table allocation */
 	efx->next_buffer_table = next_buffer_table;
@@ -837,7 +917,9 @@
 		efx_init_napi_channel(efx->channel[i]);
 	}
 
+	efx_set_xdp_channels(efx);
 out:
+	efx->ptp_data = NULL;
 	/* Destroy unused channel structures */
 	for (i = 0; i < efx->n_channels; i++) {
 		channel = other_channel[i];
@@ -848,6 +930,7 @@
 		}
 	}
 
+	efx->ptp_data = ptp_data;
 	rc2 = efx_soft_enable_interrupts(efx);
 	if (rc2) {
 		rc = rc ? rc : rc2;
@@ -864,40 +947,17 @@
 	/* Swap back */
 	efx->rxq_entries = old_rxq_entries;
 	efx->txq_entries = old_txq_entries;
-	for (i = 0; i < efx->n_channels; i++) {
-		channel = efx->channel[i];
-		efx->channel[i] = other_channel[i];
-		other_channel[i] = channel;
-	}
+	for (i = 0; i < efx->n_channels; i++)
+		swap(efx->channel[i], other_channel[i]);
+	efx_ptp_update_channel(efx, ptp_channel);
 	goto out;
 }
 
-static inline int
-efx_set_xdp_tx_queue(struct efx_nic *efx, int xdp_queue_number,
-		     struct efx_tx_queue *tx_queue)
-{
-	if (xdp_queue_number >= efx->xdp_tx_queue_count)
-		return -EINVAL;
-
-	netif_dbg(efx, drv, efx->net_dev, "Channel %u TXQ %u is XDP %u, HW %u\n",
-		  tx_queue->channel->channel, tx_queue->label,
-		  xdp_queue_number, tx_queue->queue);
-	efx->xdp_tx_queues[xdp_queue_number] = tx_queue;
-	return 0;
-}
-
 int efx_set_channels(struct efx_nic *efx)
 {
-	struct efx_tx_queue *tx_queue;
 	struct efx_channel *channel;
-	unsigned int next_queue = 0;
-	int xdp_queue_number;
 	int rc;
 
-	efx->tx_channel_offset =
-		efx_separate_tx_channels ?
-		efx->n_channels - efx->n_tx_channels : 0;
-
 	if (efx->xdp_tx_queue_count) {
 		EFX_WARN_ON_PARANOID(efx->xdp_tx_queues);
 
@@ -909,61 +969,14 @@
 			return -ENOMEM;
 	}
 
-	/* We need to mark which channels really have RX and TX
-	 * queues, and adjust the TX queue numbers if we have separate
-	 * RX-only and TX-only channels.
-	 */
-	xdp_queue_number = 0;
 	efx_for_each_channel(channel, efx) {
 		if (channel->channel < efx->n_rx_channels)
 			channel->rx_queue.core_index = channel->channel;
 		else
 			channel->rx_queue.core_index = -1;
-
-		if (channel->channel >= efx->tx_channel_offset) {
-			if (efx_channel_is_xdp_tx(channel)) {
-				efx_for_each_channel_tx_queue(tx_queue, channel) {
-					tx_queue->queue = next_queue++;
-					rc = efx_set_xdp_tx_queue(efx, xdp_queue_number, tx_queue);
-					if (rc == 0)
-						xdp_queue_number++;
-				}
-			} else {
-				efx_for_each_channel_tx_queue(tx_queue, channel) {
-					tx_queue->queue = next_queue++;
-					netif_dbg(efx, drv, efx->net_dev, "Channel %u TXQ %u is HW %u\n",
-						  channel->channel, tx_queue->label,
-						  tx_queue->queue);
-				}
-
-				/* If XDP is borrowing queues from net stack, it must use the queue
-				 * with no csum offload, which is the first one of the channel
-				 * (note: channel->tx_queue_by_type is not initialized yet)
-				 */
-				if (efx->xdp_txq_queues_mode == EFX_XDP_TX_QUEUES_BORROWED) {
-					tx_queue = &channel->tx_queue[0];
-					rc = efx_set_xdp_tx_queue(efx, xdp_queue_number, tx_queue);
-					if (rc == 0)
-						xdp_queue_number++;
-				}
-			}
-		}
 	}
-	WARN_ON(efx->xdp_txq_queues_mode == EFX_XDP_TX_QUEUES_DEDICATED &&
-		xdp_queue_number != efx->xdp_tx_queue_count);
-	WARN_ON(efx->xdp_txq_queues_mode != EFX_XDP_TX_QUEUES_DEDICATED &&
-		xdp_queue_number > efx->xdp_tx_queue_count);
 
-	/* If we have more CPUs than assigned XDP TX queues, assign the already
-	 * existing queues to the exceeding CPUs
-	 */
-	next_queue = 0;
-	while (xdp_queue_number < efx->xdp_tx_queue_count) {
-		tx_queue = efx->xdp_tx_queues[next_queue++];
-		rc = efx_set_xdp_tx_queue(efx, xdp_queue_number, tx_queue);
-		if (rc == 0)
-			xdp_queue_number++;
-	}
+	efx_set_xdp_channels(efx);
 
 	rc = netif_set_real_num_tx_queues(efx->net_dev, efx->n_tx_channels);
 	if (rc)
@@ -1107,7 +1120,7 @@
 	struct efx_rx_queue *rx_queue;
 	struct efx_channel *channel;
 
-	efx_for_each_channel(channel, efx) {
+	efx_for_each_channel_rev(channel, efx) {
 		efx_for_each_channel_tx_queue(tx_queue, channel) {
 			efx_init_tx_queue(tx_queue);
 			atomic_inc(&efx->active_queues);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/efx_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/efx_common.c
@@ -181,11 +181,11 @@
 
 	/* save old address */
 	ether_addr_copy(old_addr, net_dev->dev_addr);
-	ether_addr_copy(net_dev->dev_addr, new_addr);
+	eth_hw_addr_set(net_dev, new_addr);
 	if (efx->type->set_mac_address) {
 		rc = efx->type->set_mac_address(efx);
 		if (rc) {
-			ether_addr_copy(net_dev->dev_addr, old_addr);
+			eth_hw_addr_set(net_dev, old_addr);
 			return rc;
 		}
 	}
@@ -542,6 +542,8 @@
 	/* Start the hardware monitor if there is one */
 	efx_start_monitor(efx);
 
+	efx_selftest_async_start(efx);
+
 	/* Link state detection is normally event-driven; we have
 	 * to poll now because we could have missed a change
 	 */
@@ -897,7 +899,7 @@
 	 * have changed by now.  Now that we have the RTNL lock,
 	 * it cannot change again.
 	 */
-	if (efx->state == STATE_READY)
+	if (efx_net_active(efx->state))
 		(void)efx_reset(efx, method);
 
 	rtnl_unlock();
@@ -907,7 +909,7 @@
 {
 	enum reset_type method;
 
-	if (efx->state == STATE_RECOVERY) {
+	if (efx_recovering(efx->state)) {
 		netif_dbg(efx, drv, efx->net_dev,
 			  "recovering: skip scheduling %s reset\n",
 			  RESET_TYPE(type));
@@ -942,7 +944,7 @@
 	/* If we're not READY then just leave the flags set as the cue
 	 * to abort probing or reschedule the reset later.
 	 */
-	if (READ_ONCE(efx->state) != STATE_READY)
+	if (!efx_net_active(READ_ONCE(efx->state)))
 		return;
 
 	/* efx_process_channel() will no longer read events once a
@@ -1216,7 +1218,7 @@
 	rtnl_lock();
 
 	if (efx->state != STATE_DISABLED) {
-		efx->state = STATE_RECOVERY;
+		efx->state = efx_recover(efx->state);
 		efx->reset_pending = 0;
 
 		efx_device_detach_sync(efx);
@@ -1270,7 +1272,7 @@
 		netif_err(efx, hw, efx->net_dev,
 			  "efx_reset failed after PCI error (%d)\n", rc);
 	} else {
-		efx->state = STATE_READY;
+		efx->state = efx_recovered(efx->state);
 		netif_dbg(efx, hw, efx->net_dev,
 			  "Done resetting and resuming IO after PCI error.\n");
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/efx_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/efx_common.h
@@ -45,9 +45,7 @@
 
 #define EFX_ASSERT_RESET_SERIALISED(efx)		\
 	do {						\
-		if ((efx->state == STATE_READY) ||	\
-		    (efx->state == STATE_RECOVERY) ||	\
-		    (efx->state == STATE_DISABLED))	\
+		if (efx->state != STATE_UNINIT)		\
 			ASSERT_RTNL();			\
 	} while (0)
 
@@ -64,7 +62,7 @@
 
 static inline int efx_check_disabled(struct efx_nic *efx)
 {
-	if (efx->state == STATE_DISABLED || efx->state == STATE_RECOVERY) {
+	if (efx->state == STATE_DISABLED || efx_recovering(efx->state)) {
 		netif_err(efx, drv, efx->net_dev,
 			  "device is disabled due to earlier errors\n");
 		return -EIO;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ethtool_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ethtool_common.c
@@ -137,7 +137,7 @@
 	if (!efx_tests)
 		goto fail;
 
-	if (efx->state != STATE_READY) {
+	if (!efx_net_active(efx->state)) {
 		rc = -EBUSY;
 		goto out;
 	}
@@ -563,20 +563,14 @@
 {
 	struct efx_nic *efx = netdev_priv(net_dev);
 	struct efx_link_state *link_state = &efx->link_state;
-	u32 supported;
 
 	mutex_lock(&efx->mac_lock);
 	efx_mcdi_phy_get_link_ksettings(efx, cmd);
 	mutex_unlock(&efx->mac_lock);
 
 	/* Both MACs support pause frames (bidirectional and respond-only) */
-	ethtool_convert_link_mode_to_legacy_u32(&supported,
-						cmd->link_modes.supported);
-
-	supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
-
-	ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported,
-						supported);
+	ethtool_link_ksettings_add_link_mode(cmd, supported, Pause);
+	ethtool_link_ksettings_add_link_mode(cmd, supported, Asym_Pause);
 
 	if (LOOPBACK_INTERNAL(efx)) {
 		cmd->base.speed = link_state->speed;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/falcon/efx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/falcon/efx.c
@@ -1044,7 +1044,7 @@
 		return rc;
 
 	/* Initialise MAC address to permanent address */
-	ether_addr_copy(efx->net_dev->dev_addr, efx->net_dev->perm_addr);
+	eth_hw_addr_set(efx->net_dev, efx->net_dev->perm_addr);
 
 	return 0;
 }
@@ -2162,11 +2162,11 @@
 
 	/* save old address */
 	ether_addr_copy(old_addr, net_dev->dev_addr);
-	ether_addr_copy(net_dev->dev_addr, new_addr);
+	eth_hw_addr_set(net_dev, new_addr);
 	if (efx->type->set_mac_address) {
 		rc = efx->type->set_mac_address(efx);
 		if (rc) {
-			ether_addr_copy(net_dev->dev_addr, old_addr);
+			eth_hw_addr_set(net_dev, old_addr);
 			return rc;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/falcon/rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/falcon/rx.c
@@ -110,6 +110,8 @@
 	struct ef4_rx_page_state *state;
 	unsigned index;
 
+	if (unlikely(!rx_queue->page_ring))
+		return NULL;
 	index = rx_queue->page_remove & rx_queue->page_ptr_mask;
 	page = rx_queue->page_ring[index];
 	if (page == NULL)
@@ -293,6 +295,9 @@
 {
 	struct ef4_rx_queue *rx_queue = ef4_channel_get_rx_queue(channel);
 
+	if (unlikely(!rx_queue->page_ring))
+		return;
+
 	do {
 		ef4_recycle_rx_page(channel, rx_buf);
 		rx_buf = ef4_rx_buf_next(rx_queue, rx_buf);
@@ -728,7 +733,10 @@
 					    efx->rx_bufs_per_page);
 	rx_queue->page_ring = kcalloc(page_ring_size,
 				      sizeof(*rx_queue->page_ring), GFP_KERNEL);
-	rx_queue->page_ptr_mask = page_ring_size - 1;
+	if (!rx_queue->page_ring)
+		rx_queue->page_ptr_mask = 0;
+	else
+		rx_queue->page_ptr_mask = page_ring_size - 1;
 }
 
 void ef4_init_rx_queue(struct ef4_rx_queue *rx_queue)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/filter.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/filter.h
@@ -157,7 +157,8 @@
 	u32	flags:6;
 	u32	dmaq_id:12;
 	u32	rss_context;
-	__be16	outer_vid __aligned(4); /* allow jhash2() of match values */
+	u32	vport_id;
+	__be16	outer_vid;
 	__be16	inner_vid;
 	u8	loc_mac[ETH_ALEN];
 	u8	rem_mac[ETH_ALEN];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/mcdi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/mcdi.c
@@ -163,9 +163,9 @@
 	/* Serialise with efx_mcdi_ev_cpl() and efx_mcdi_ev_death() */
 	spin_lock_bh(&mcdi->iface_lock);
 	++mcdi->seqno;
+	seqno = mcdi->seqno & SEQ_MASK;
 	spin_unlock_bh(&mcdi->iface_lock);
 
-	seqno = mcdi->seqno & SEQ_MASK;
 	xflags = 0;
 	if (mcdi->mode == MCDI_MODE_EVENTS)
 		xflags |= MCDI_HEADER_XFLAGS_EVREQ;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/mcdi_port_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/mcdi_port_common.c
@@ -974,12 +974,15 @@
 
 	/* A QSFP+ NIC may actually have an SFP+ module attached.
 	 * The ID is page 0, byte 0.
+	 * QSFP28 is of type SFF_8636, however, this is treated
+	 * the same by ethtool, so we can also treat them the same.
 	 */
 	switch (efx_mcdi_phy_get_module_eeprom_byte(efx, 0, 0)) {
-	case 0x3:
+	case 0x3: /* SFP */
 		return MC_CMD_MEDIA_SFP_PLUS;
-	case 0xc:
-	case 0xd:
+	case 0xc: /* QSFP */
+	case 0xd: /* QSFP+ */
+	case 0x11: /* QSFP28 */
 		return MC_CMD_MEDIA_QSFP_PLUS;
 	default:
 		return 0;
@@ -1077,7 +1080,7 @@
 
 	case MC_CMD_MEDIA_QSFP_PLUS:
 		modinfo->type = ETH_MODULE_SFF_8436;
-		modinfo->eeprom_len = ETH_MODULE_SFF_8436_LEN;
+		modinfo->eeprom_len = ETH_MODULE_SFF_8436_MAX_LEN;
 		break;
 
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/net_driver.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/net_driver.h
@@ -627,12 +627,54 @@
 #define EFX_INT_MODE_USE_MSI(x) (((x)->interrupt_mode) <= EFX_INT_MODE_MSI)
 
 enum nic_state {
-	STATE_UNINIT = 0,	/* device being probed/removed or is frozen */
-	STATE_READY = 1,	/* hardware ready and netdev registered */
-	STATE_DISABLED = 2,	/* device disabled due to hardware errors */
-	STATE_RECOVERY = 3,	/* device recovering from PCI error */
+	STATE_UNINIT = 0,	/* device being probed/removed */
+	STATE_NET_DOWN,		/* hardware probed and netdev registered */
+	STATE_NET_UP,		/* ready for traffic */
+	STATE_DISABLED,		/* device disabled due to hardware errors */
+
+	STATE_RECOVERY = 0x100,/* recovering from PCI error */
+	STATE_FROZEN = 0x200,	/* frozen by power management */
 };
 
+static inline bool efx_net_active(enum nic_state state)
+{
+	return state == STATE_NET_DOWN || state == STATE_NET_UP;
+}
+
+static inline bool efx_frozen(enum nic_state state)
+{
+	return state & STATE_FROZEN;
+}
+
+static inline bool efx_recovering(enum nic_state state)
+{
+	return state & STATE_RECOVERY;
+}
+
+static inline enum nic_state efx_freeze(enum nic_state state)
+{
+	WARN_ON(!efx_net_active(state));
+	return state | STATE_FROZEN;
+}
+
+static inline enum nic_state efx_thaw(enum nic_state state)
+{
+	WARN_ON(!efx_frozen(state));
+	return state & ~STATE_FROZEN;
+}
+
+static inline enum nic_state efx_recover(enum nic_state state)
+{
+	WARN_ON(!efx_net_active(state));
+	return state | STATE_RECOVERY;
+}
+
+static inline enum nic_state efx_recovered(enum nic_state state)
+{
+	WARN_ON(!efx_recovering(state));
+	return state & ~STATE_RECOVERY;
+}
+
 /* Forward declaration */
 struct efx_nic;
 
@@ -1282,6 +1324,7 @@
  * @udp_tnl_has_port: Check if a port has been added as UDP tunnel
  * @print_additional_fwver: Dump NIC-specific additional FW version info
  * @sensor_event: Handle a sensor event from MCDI
+ * @rx_recycle_ring_size: Size of the RX recycle ring
  * @revision: Hardware architecture revision
  * @txd_ptr_tbl_base: TX descriptor ring base address
  * @rxd_ptr_tbl_base: RX descriptor ring base address
@@ -1440,7 +1483,7 @@
 	bool (*sriov_wanted)(struct efx_nic *efx);
 	void (*sriov_reset)(struct efx_nic *efx);
 	void (*sriov_flr)(struct efx_nic *efx, unsigned vf_i);
-	int (*sriov_set_vf_mac)(struct efx_nic *efx, int vf_i, u8 *mac);
+	int (*sriov_set_vf_mac)(struct efx_nic *efx, int vf_i, const u8 *mac);
 	int (*sriov_set_vf_vlan)(struct efx_nic *efx, int vf_i, u16 vlan,
 				 u8 qos);
 	int (*sriov_set_vf_spoofchk)(struct efx_nic *efx, int vf_i,
@@ -1460,6 +1503,7 @@
 	size_t (*print_additional_fwver)(struct efx_nic *efx, char *buf,
 					 size_t len);
 	void (*sensor_event)(struct efx_nic *efx, efx_qword_t *ev);
+	unsigned int (*rx_recycle_ring_size)(const struct efx_nic *efx);
 
 	int revision;
 	unsigned int txd_ptr_tbl_base;
@@ -1533,7 +1577,7 @@
 
 static inline bool efx_channel_has_tx_queues(struct efx_channel *channel)
 {
-	return true;
+	return channel && channel->channel >= channel->efx->tx_channel_offset;
 }
 
 static inline unsigned int efx_channel_num_tx_queues(struct efx_channel *channel)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/nic_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/nic_common.h
@@ -195,6 +195,11 @@
 		efx->type->sensor_event(efx, ev);
 }
 
+static inline unsigned int efx_rx_recycle_ring_size(const struct efx_nic *efx)
+{
+	return efx->type->rx_recycle_ring_size(efx);
+}
+
 /* Some statistics are computed as A - B where A and B each increase
  * linearly with some hardware counter(s) and the counters are read
  * asynchronously.  If the counters contributing to B are always read
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ptp.c
@@ -45,6 +45,7 @@
 #include "farch_regs.h"
 #include "tx.h"
 #include "nic.h" /* indirectly includes ptp.h */
+#include "efx_channels.h"
 
 /* Maximum number of events expected to make up a PTP event */
 #define	MAX_EVENT_FRAGS			3
@@ -541,6 +542,12 @@
 	return efx->ptp_data ? efx->ptp_data->channel : NULL;
 }
 
+void efx_ptp_update_channel(struct efx_nic *efx, struct efx_channel *channel)
+{
+	if (efx->ptp_data)
+		efx->ptp_data->channel = channel;
+}
+
 static u32 last_sync_timestamp_major(struct efx_nic *efx)
 {
 	struct efx_channel *channel = efx_ptp_channel(efx);
@@ -1093,7 +1100,29 @@
 
 	tx_queue = efx_channel_get_tx_queue(ptp_data->channel, type);
 	if (tx_queue && tx_queue->timestamping) {
+		/* This code invokes normal driver TX code which is always
+		 * protected from softirqs when called from generic TX code,
+		 * which in turn disables preemption. Look at __dev_queue_xmit
+		 * which uses rcu_read_lock_bh disabling preemption for RCU
+		 * plus disabling softirqs. We do not need RCU reader
+		 * protection here.
+		 *
+		 * Although it is theoretically safe for current PTP TX/RX code
+		 * running without disabling softirqs, there are three good
+		 * reasond for doing so:
+		 *
+		 *      1) The code invoked is mainly implemented for non-PTP
+		 *         packets and it is always executed with softirqs
+		 *         disabled.
+		 *      2) This being a single PTP packet, better to not
+		 *         interrupt its processing by softirqs which can lead
+		 *         to high latencies.
+		 *      3) netdev_xmit_more checks preemption is disabled and
+		 *         triggers a BUG_ON if not.
+		 */
+		local_bh_disable();
 		efx_enqueue_skb(tx_queue, skb);
+		local_bh_enable();
 	} else {
 		WARN_ONCE(1, "PTP channel has no timestamped tx queue\n");
 		dev_kfree_skb_any(skb);
@@ -1443,6 +1472,11 @@
 	int rc = 0;
 	unsigned int pos;
 
+	if (efx->ptp_data) {
+		efx->ptp_data->channel = channel;
+		return 0;
+	}
+
 	ptp = kzalloc(sizeof(struct efx_ptp_data), GFP_KERNEL);
 	efx->ptp_data = ptp;
 	if (!efx->ptp_data)
@@ -2179,7 +2213,7 @@
 	.pre_probe		= efx_ptp_probe_channel,
 	.post_remove		= efx_ptp_remove_channel,
 	.get_name		= efx_ptp_get_channel_name,
-	/* no copy operation; there is no need to reallocate this channel */
+	.copy                   = efx_copy_channel,
 	.receive_skb		= efx_ptp_rx,
 	.want_txqs		= efx_ptp_want_txqs,
 	.keep_eventq		= false,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/ptp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/ptp.h
@@ -16,6 +16,7 @@
 int efx_ptp_probe(struct efx_nic *efx, struct efx_channel *channel);
 void efx_ptp_defer_probe_with_channel(struct efx_nic *efx);
 struct efx_channel *efx_ptp_channel(struct efx_nic *efx);
+void efx_ptp_update_channel(struct efx_nic *efx, struct efx_channel *channel);
 void efx_ptp_remove(struct efx_nic *efx);
 int efx_ptp_set_ts_config(struct efx_nic *efx, struct ifreq *ifr);
 int efx_ptp_get_ts_config(struct efx_nic *efx, struct ifreq *ifr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/rx_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/rx_common.c
@@ -23,13 +23,6 @@
 MODULE_PARM_DESC(rx_refill_threshold,
 		 "RX descriptor ring refill threshold (%)");
 
-/* Number of RX buffers to recycle pages for.  When creating the RX page recycle
- * ring, this number is divided by the number of buffers per page to calculate
- * the number of pages to store in the RX page recycle ring.
- */
-#define EFX_RECYCLE_RING_SIZE_IOMMU 4096
-#define EFX_RECYCLE_RING_SIZE_NOIOMMU (2 * EFX_RX_PREFERRED_BATCH)
-
 /* RX maximum head room required.
  *
  * This must be at least 1 to prevent overflow, plus one packet-worth
@@ -45,6 +38,8 @@
 	unsigned int index;
 	struct page *page;
 
+	if (unlikely(!rx_queue->page_ring))
+		return NULL;
 	index = rx_queue->page_remove & rx_queue->page_ptr_mask;
 	page = rx_queue->page_ring[index];
 	if (page == NULL)
@@ -114,6 +109,9 @@
 {
 	struct efx_rx_queue *rx_queue = efx_channel_get_rx_queue(channel);
 
+	if (unlikely(!rx_queue->page_ring))
+		return;
+
 	do {
 		efx_recycle_rx_page(channel, rx_buf);
 		rx_buf = efx_rx_buf_next(rx_queue, rx_buf);
@@ -136,21 +134,15 @@
 	unsigned int bufs_in_recycle_ring, page_ring_size;
 	struct efx_nic *efx = rx_queue->efx;
 
-	/* Set the RX recycle ring size */
-#ifdef CONFIG_PPC64
-	bufs_in_recycle_ring = EFX_RECYCLE_RING_SIZE_IOMMU;
-#else
-	if (iommu_present(&pci_bus_type))
-		bufs_in_recycle_ring = EFX_RECYCLE_RING_SIZE_IOMMU;
-	else
-		bufs_in_recycle_ring = EFX_RECYCLE_RING_SIZE_NOIOMMU;
-#endif /* CONFIG_PPC64 */
-
+	bufs_in_recycle_ring = efx_rx_recycle_ring_size(efx);
 	page_ring_size = roundup_pow_of_two(bufs_in_recycle_ring /
 					    efx->rx_bufs_per_page);
 	rx_queue->page_ring = kcalloc(page_ring_size,
 				      sizeof(*rx_queue->page_ring), GFP_KERNEL);
-	rx_queue->page_ptr_mask = page_ring_size - 1;
+	if (!rx_queue->page_ring)
+		rx_queue->page_ptr_mask = 0;
+	else
+		rx_queue->page_ptr_mask = page_ring_size - 1;
 }
 
 static void efx_fini_rx_recycle_ring(struct efx_rx_queue *rx_queue)
@@ -158,6 +150,9 @@
 	struct efx_nic *efx = rx_queue->efx;
 	int i;
 
+	if (unlikely(!rx_queue->page_ring))
+		return;
+
 	/* Unmap and release the pages in the recycle ring. Remove the ring. */
 	for (i = 0; i <= rx_queue->page_ptr_mask; i++) {
 		struct page *page = rx_queue->page_ring[i];
@@ -665,17 +660,17 @@
 	     (EFX_FILTER_FLAG_RX | EFX_FILTER_FLAG_TX)))
 		return false;
 
-	return memcmp(&left->outer_vid, &right->outer_vid,
+	return memcmp(&left->vport_id, &right->vport_id,
 		      sizeof(struct efx_filter_spec) -
-		      offsetof(struct efx_filter_spec, outer_vid)) == 0;
+		      offsetof(struct efx_filter_spec, vport_id)) == 0;
 }
 
 u32 efx_filter_spec_hash(const struct efx_filter_spec *spec)
 {
-	BUILD_BUG_ON(offsetof(struct efx_filter_spec, outer_vid) & 3);
-	return jhash2((const u32 *)&spec->outer_vid,
+	BUILD_BUG_ON(offsetof(struct efx_filter_spec, vport_id) & 3);
+	return jhash2((const u32 *)&spec->vport_id,
 		      (sizeof(struct efx_filter_spec) -
-		       offsetof(struct efx_filter_spec, outer_vid)) / 4,
+		       offsetof(struct efx_filter_spec, vport_id)) / 4,
 		      0);
 }
 
@@ -826,8 +821,10 @@
 		}
 
 		if (!success) {
-			efx_for_each_channel(channel, efx)
+			efx_for_each_channel(channel, efx) {
 				kfree(channel->rps_flow_id);
+				channel->rps_flow_id = NULL;
+			}
 			efx->type->filter_table_remove(efx);
 			rc = -ENOMEM;
 			goto out_unlock;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/rx_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/rx_common.h
@@ -18,6 +18,12 @@
 #define EFX_RX_MAX_FRAGS DIV_ROUND_UP(EFX_MAX_FRAME_LEN(EFX_MAX_MTU), \
 				      EFX_RX_USR_BUF_SIZE)
 
+/* Number of RX buffers to recycle pages for.  When creating the RX page recycle
+ * ring, this number is divided by the number of buffers per page to calculate
+ * the number of pages to store in the RX page recycle ring.
+ */
+#define EFX_RECYCLE_RING_SIZE_10G	256
+
 static inline u8 *efx_rx_buf_va(struct efx_rx_buffer *buf)
 {
 	return page_address(buf->page) + buf->page_offset;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/siena.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/siena.c
@@ -25,6 +25,7 @@
 #include "mcdi_port_common.h"
 #include "selftest.h"
 #include "siena_sriov.h"
+#include "rx_common.h"
 
 /* Hardware control for SFC9000 family including SFL9021 (aka Siena). */
 
@@ -958,6 +959,12 @@
 	return 0;
 }
 
+static unsigned int efx_siena_recycle_ring_size(const struct efx_nic *efx)
+{
+	/* Maximum link speed is 10G */
+	return EFX_RECYCLE_RING_SIZE_10G;
+}
+
 /**************************************************************************
  *
  * Revision-dependent attributes used by efx.c and nic.c
@@ -1098,4 +1105,5 @@
 	.rx_hash_key_size = 16,
 	.check_caps = siena_check_caps,
 	.sensor_event = efx_mcdi_sensor_event,
+	.rx_recycle_ring_size = efx_siena_recycle_ring_size,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/siena_sriov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/siena_sriov.c
@@ -1591,7 +1591,7 @@
 	destroy_workqueue(vfdi_workqueue);
 }
 
-int efx_siena_sriov_set_vf_mac(struct efx_nic *efx, int vf_i, u8 *mac)
+int efx_siena_sriov_set_vf_mac(struct efx_nic *efx, int vf_i, const u8 *mac)
 {
 	struct siena_nic_data *nic_data = efx->nic_data;
 	struct siena_vf *vf;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/siena_sriov.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/siena_sriov.h
@@ -46,7 +46,7 @@
 void efx_siena_sriov_reset(struct efx_nic *efx);
 void efx_siena_sriov_flr(struct efx_nic *efx, unsigned flr);
 
-int efx_siena_sriov_set_vf_mac(struct efx_nic *efx, int vf, u8 *mac);
+int efx_siena_sriov_set_vf_mac(struct efx_nic *efx, int vf, const u8 *mac);
 int efx_siena_sriov_set_vf_vlan(struct efx_nic *efx, int vf,
 				u16 vlan, u8 qos);
 int efx_siena_sriov_set_vf_spoofchk(struct efx_nic *efx, int vf,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/tx.c
@@ -443,6 +443,9 @@
 	if (unlikely(!tx_queue))
 		return -EINVAL;
 
+	if (!tx_queue->initialised)
+		return -EINVAL;
+
 	if (efx->xdp_txq_queues_mode != EFX_XDP_TX_QUEUES_DEDICATED)
 		HARD_TX_LOCK(efx->net_dev, tx_queue->core_txq, cpu);
 
@@ -545,7 +548,7 @@
 		 * previous packets out.
 		 */
 		if (!netdev_xmit_more())
-			efx_tx_send_pending(tx_queue->channel);
+			efx_tx_send_pending(efx_get_tx_channel(efx, index));
 		return NETDEV_TX_OK;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/tx_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/tx_common.c
@@ -101,6 +101,8 @@
 	netif_dbg(tx_queue->efx, drv, tx_queue->efx->net_dev,
 		  "shutting down TX queue %d\n", tx_queue->queue);
 
+	tx_queue->initialised = false;
+
 	if (!tx_queue->buffer)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sfc/tx_tso.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sfc/tx_tso.c
@@ -147,7 +147,7 @@
 	EFX_WARN_ON_ONCE_PARANOID(((struct ethhdr *)skb->data)->h_proto !=
 				  protocol);
 	if (protocol == htons(ETH_P_8021Q)) {
-		struct vlan_ethhdr *veh = (struct vlan_ethhdr *)skb->data;
+		struct vlan_ethhdr *veh = skb_vlan_eth_hdr(skb);
 
 		protocol = veh->h_vlan_encapsulated_proto;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sis/sis900.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sis/sis900.c
@@ -1098,7 +1098,7 @@
 
 	/* load MAC addr to filter data register */
 	for (i = 0 ; i < 3 ; i++) {
-		u32 w = (u32) *((u16 *)(net_dev->dev_addr)+i);
+		u32 w = (u32) *((const u16 *)(net_dev->dev_addr)+i);
 
 		sw32(rfcr, i << RFADDR_shift);
 		sw32(rfdr, w);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/smsc/epic100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/smsc/epic100.c
@@ -1513,14 +1513,14 @@
 	struct net_device *dev = pci_get_drvdata(pdev);
 	struct epic_private *ep = netdev_priv(dev);
 
+	unregister_netdev(dev);
 	dma_free_coherent(&pdev->dev, TX_TOTAL_SIZE, ep->tx_ring,
 			  ep->tx_ring_dma);
 	dma_free_coherent(&pdev->dev, RX_TOTAL_SIZE, ep->rx_ring,
 			  ep->rx_ring_dma);
-	unregister_netdev(dev);
 	pci_iounmap(pdev, ep->ioaddr);
-	pci_release_regions(pdev);
 	free_netdev(dev);
+	pci_release_regions(pdev);
 	pci_disable_device(pdev);
 	/* pci_power_off(pdev, -1); */
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/smsc/smc911x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/smsc/smc911x.c
@@ -2070,6 +2070,11 @@
 
 	ndev->dma = (unsigned char)-1;
 	ndev->irq = platform_get_irq(pdev, 0);
+	if (ndev->irq < 0) {
+		ret = ndev->irq;
+		goto release_both;
+	}
+
 	lp = netdev_priv(ndev);
 	lp->netdev = ndev;
 #ifdef SMC_DYNAMIC_BUS_CONFIG
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/smsc/smc91x.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/smsc/smc91x.h
@@ -175,8 +175,8 @@
 		writew(*wp++, a);
 }
 
-#define SMC_inw(a, r)		_swapw(readw((a) + (r)))
-#define SMC_outw(lp, v, a, r)	writew(_swapw(v), (a) + (r))
+#define SMC_inw(a, r)		ioread16be((a) + (r))
+#define SMC_outw(lp, v, a, r)	iowrite16be(v, (a) + (r))
 #define SMC_insw(a, r, p, l)	mcf_insw(a + r, p, l)
 #define SMC_outsw(a, r, p, l)	mcf_outsw(a + r, p, l)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/smsc/smsc911x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/smsc/smsc911x.c
@@ -1064,6 +1064,7 @@
 			     struct net_device *dev)
 {
 	struct smsc911x_data *pdata = netdev_priv(dev);
+	struct phy_device *phydev;
 	int err = -ENXIO;
 
 	pdata->mii_bus = mdiobus_alloc();
@@ -1106,6 +1107,10 @@
 		goto err_out_free_bus_2;
 	}
 
+	phydev = phy_find_first(pdata->mii_bus);
+	if (phydev)
+		phydev->mac_managed_pm = true;
+
 	return 0;
 
 err_out_free_bus_2:
@@ -1503,7 +1508,7 @@
 
 /* Sets the device MAC address to dev_addr, called with mac_lock held */
 static void
-smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6])
+smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, const u8 dev_addr[6])
 {
 	u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4];
 	u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
@@ -2429,7 +2434,7 @@
 	if (irq == -EPROBE_DEFER) {
 		retval = -EPROBE_DEFER;
 		goto out_0;
-	} else if (irq <= 0) {
+	} else if (irq < 0) {
 		pr_warn("Could not allocate irq resource\n");
 		retval = -ENODEV;
 		goto out_0;
@@ -2584,6 +2589,8 @@
 	if (netif_running(ndev)) {
 		netif_stop_queue(ndev);
 		netif_device_detach(ndev);
+		if (!device_may_wakeup(dev))
+			phy_stop(ndev->phydev);
 	}
 
 	/* enable wake on LAN, energy detection and the external PME
@@ -2625,6 +2632,8 @@
 	if (netif_running(ndev)) {
 		netif_device_attach(ndev);
 		netif_start_queue(ndev);
+		if (!device_may_wakeup(dev))
+			phy_start(ndev->phydev);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/smsc/smsc9420.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/smsc/smsc9420.c
@@ -404,7 +404,7 @@
 static void smsc9420_set_mac_address(struct net_device *dev)
 {
 	struct smsc9420_pdata *pd = netdev_priv(dev);
-	u8 *dev_addr = dev->dev_addr;
+	const u8 *dev_addr = dev->dev_addr;
 	u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4];
 	u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
 	    (dev_addr[1] << 8) | dev_addr[0];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/socionext/netsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/socionext/netsec.c
@@ -1851,6 +1851,17 @@
 		return err;
 	}
 
+	/*
+	 * SynQuacer is physically configured with TX and RX delays
+	 * but the standard firmware claimed otherwise for a long
+	 * time, ignore it.
+	 */
+	if (of_machine_is_compatible("socionext,developer-box") &&
+	    priv->phy_interface != PHY_INTERFACE_MODE_RGMII_ID) {
+		dev_warn(&pdev->dev, "Outdated firmware reports incorrect PHY mode, overriding\n");
+		priv->phy_interface = PHY_INTERFACE_MODE_RGMII_ID;
+	}
+
 	priv->phy_np = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0);
 	if (!priv->phy_np) {
 		dev_err(&pdev->dev, "missing required property 'phy-handle'\n");
@@ -1964,11 +1975,13 @@
 			ret = PTR_ERR(priv->phydev);
 			dev_err(priv->dev, "get_phy_device err(%d)\n", ret);
 			priv->phydev = NULL;
+			mdiobus_unregister(bus);
 			return -ENODEV;
 		}
 
 		ret = phy_device_register(priv->phydev);
 		if (ret) {
+			phy_device_free(priv->phydev);
 			mdiobus_unregister(bus);
 			dev_err(priv->dev,
 				"phy_device_register err(%d)\n", ret);
@@ -2039,7 +2052,7 @@
 
 	mac = device_get_mac_address(&pdev->dev, macbuf, sizeof(macbuf));
 	if (mac)
-		ether_addr_copy(ndev->dev_addr, mac);
+		eth_hw_addr_set(ndev, mac);
 
 	if (priv->eeprom_base &&
 	    (!mac || !is_valid_ether_addr(ndev->dev_addr))) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/socionext/sni_ave.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/socionext/sni_ave.c
@@ -1229,6 +1229,8 @@
 
 	phy_support_asym_pause(phydev);
 
+	phydev->mac_managed_pm = true;
+
 	phy_attached_info(phydev);
 
 	return 0;
@@ -1599,7 +1601,7 @@
 
 	ndev->max_mtu = AVE_MAX_ETHFRAME - (ETH_HLEN + ETH_FCS_LEN);
 
-	ret = of_get_mac_address(np, ndev->dev_addr);
+	ret = of_get_ethdev_address(np, ndev);
 	if (ret) {
 		/* if the mac address is invalid, use random mac address */
 		eth_hw_addr_random(ndev);
@@ -1758,6 +1760,10 @@
 
 	ave_global_reset(ndev);
 
+	ret = phy_init_hw(ndev->phydev);
+	if (ret)
+		return ret;
+
 	ave_ethtool_get_wol(ndev, &wol);
 	wol.wolopts = priv->wolopts;
 	__ave_ethtool_set_wol(ndev, &wol);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -253,7 +253,7 @@
 config DWMAC_LOONGSON
 	tristate "Loongson PCI DWMAC support"
 	default MACH_LOONGSON64
-	depends on STMMAC_ETH && PCI
+	depends on (MACH_LOONGSON64 || COMPILE_TEST) && STMMAC_ETH && PCI
 	depends on COMMON_CLK
 	help
 	  This selects the LOONGSON PCI bus support for the stmmac driver,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/altr_tse_pcs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/altr_tse_pcs.c
@@ -57,10 +57,6 @@
 #define TSE_PCS_USE_SGMII_ENA				BIT(0)
 #define TSE_PCS_IF_USE_SGMII				0x03
 
-#define SGMII_ADAPTER_CTRL_REG				0x00
-#define SGMII_ADAPTER_DISABLE				0x0001
-#define SGMII_ADAPTER_ENABLE				0x0000
-
 #define AUTONEGO_LINK_TIMER				20
 
 static int tse_pcs_reset(void __iomem *base, struct tse_pcs *pcs)
@@ -202,12 +198,8 @@
 			   unsigned int speed)
 {
 	void __iomem *tse_pcs_base = pcs->tse_pcs_base;
-	void __iomem *sgmii_adapter_base = pcs->sgmii_adapter_base;
 	u32 val;
 
-	writew(SGMII_ADAPTER_ENABLE,
-	       sgmii_adapter_base + SGMII_ADAPTER_CTRL_REG);
-
 	pcs->autoneg = phy_dev->autoneg;
 
 	if (phy_dev->autoneg == AUTONEG_ENABLE) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/altr_tse_pcs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/altr_tse_pcs.h
@@ -10,6 +10,10 @@
 #include <linux/phy.h>
 #include <linux/timer.h>
 
+#define SGMII_ADAPTER_CTRL_REG		0x00
+#define SGMII_ADAPTER_ENABLE		0x0000
+#define SGMII_ADAPTER_DISABLE		0x0001
+
 struct tse_pcs {
 	struct device *dev;
 	void __iomem *tse_pcs_base;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/common.h
@@ -209,6 +209,7 @@
 	unsigned long mac_errors[32];
 	unsigned long mtl_errors[32];
 	unsigned long dma_errors[32];
+	unsigned long dma_dpp_errors[32];
 };
 
 /* Number of fields in Safety Stats */
@@ -530,7 +531,6 @@
 	unsigned int xlgmac;
 	unsigned int num_vlan;
 	u32 vlan_filter[32];
-	unsigned int promisc;
 	bool vlan_fail_q_en;
 	u8 vlan_fail_q;
 };
@@ -546,13 +546,13 @@
 int dwxgmac2_setup(struct stmmac_priv *priv);
 int dwxlgmac2_setup(struct stmmac_priv *priv);
 
-void stmmac_set_mac_addr(void __iomem *ioaddr, u8 addr[6],
+void stmmac_set_mac_addr(void __iomem *ioaddr, const u8 addr[6],
 			 unsigned int high, unsigned int low);
 void stmmac_get_mac_addr(void __iomem *ioaddr, unsigned char *addr,
 			 unsigned int high, unsigned int low);
 void stmmac_set_mac(void __iomem *ioaddr, bool enable);
 
-void stmmac_dwmac4_set_mac_addr(void __iomem *ioaddr, u8 addr[6],
+void stmmac_dwmac4_set_mac_addr(void __iomem *ioaddr, const u8 addr[6],
 				unsigned int high, unsigned int low);
 void stmmac_dwmac4_get_mac_addr(void __iomem *ioaddr, unsigned char *addr,
 				unsigned int high, unsigned int low);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c
@@ -361,6 +361,7 @@
 	data->fix_mac_speed = tegra_eqos_fix_speed;
 	data->init = tegra_eqos_init;
 	data->bsp_priv = eqos;
+	data->sph_disable = 1;
 
 	err = tegra_eqos_init(pdev, eqos);
 	if (err < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-ingenic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-ingenic.c
@@ -273,7 +273,8 @@
 			mac->tx_delay = tx_delay_ps * 1000;
 		} else {
 			dev_err(&pdev->dev, "Invalid TX clock delay: %dps\n", tx_delay_ps);
-			return -EINVAL;
+			ret = -EINVAL;
+			goto err_remove_config_dt;
 		}
 	}
 
@@ -283,7 +284,8 @@
 			mac->rx_delay = rx_delay_ps * 1000;
 		} else {
 			dev_err(&pdev->dev, "Invalid RX clock delay: %dps\n", rx_delay_ps);
-			return -EINVAL;
+			ret = -EINVAL;
+			goto err_remove_config_dt;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -298,6 +298,11 @@
 	*art_time = ns;
 }
 
+static int stmmac_cross_ts_isr(struct stmmac_priv *priv)
+{
+	return (readl(priv->ioaddr + GMAC_INT_STATUS) & GMAC_INT_TSIE);
+}
+
 static int intel_crosststamp(ktime_t *device,
 			     struct system_counterval_t *system,
 			     void *ctx)
@@ -313,8 +318,6 @@
 	u32 num_snapshot;
 	u32 gpio_value;
 	u32 acr_value;
-	int ret;
-	u32 v;
 	int i;
 
 	if (!boot_cpu_has(X86_FEATURE_ART))
@@ -328,6 +331,8 @@
 	if (priv->plat->ext_snapshot_en)
 		return -EBUSY;
 
+	priv->plat->int_snapshot_en = 1;
+
 	mutex_lock(&priv->aux_ts_lock);
 	/* Enable Internal snapshot trigger */
 	acr_value = readl(ptpaddr + PTP_ACR);
@@ -347,6 +352,7 @@
 		break;
 	default:
 		mutex_unlock(&priv->aux_ts_lock);
+		priv->plat->int_snapshot_en = 0;
 		return -EINVAL;
 	}
 	writel(acr_value, ptpaddr + PTP_ACR);
@@ -368,13 +374,12 @@
 	gpio_value |= GMAC_GPO1;
 	writel(gpio_value, ioaddr + GMAC_GPIO_STATUS);
 
-	/* Poll for time sync operation done */
-	ret = readl_poll_timeout(priv->ioaddr + GMAC_INT_STATUS, v,
-				 (v & GMAC_INT_TSIE), 100, 10000);
-
-	if (ret == -ETIMEDOUT) {
-		pr_err("%s: Wait for time sync operation timeout\n", __func__);
-		return ret;
+	/* Time sync done Indication - Interrupt method */
+	if (!wait_event_interruptible_timeout(priv->tstamp_busy_wait,
+					      stmmac_cross_ts_isr(priv),
+					      HZ / 100)) {
+		priv->plat->int_snapshot_en = 0;
+		return -ETIMEDOUT;
 	}
 
 	num_snapshot = (readl(ioaddr + GMAC_TIMESTAMP_STATUS) &
@@ -392,6 +397,7 @@
 	}
 
 	system->cycles *= intel_priv->crossts_adj;
+	priv->plat->int_snapshot_en = 0;
 
 	return 0;
 }
@@ -454,6 +460,7 @@
 	plat->has_gmac4 = 1;
 	plat->force_sf_dma_mode = 0;
 	plat->tso_en = 1;
+	plat->sph_disable = 1;
 
 	/* Multiplying factor to the clk_eee_i clock time
 	 * period to make it closer to 100 ns. This value
@@ -575,6 +582,7 @@
 
 	plat->has_crossts = true;
 	plat->crosststamp = intel_crosststamp;
+	plat->int_snapshot_en = 0;
 
 	/* Setup MSI vector offset specific to Intel mGbE controller */
 	plat->msi_mac_vec = 29;
@@ -592,7 +600,6 @@
 {
 	plat->rx_queues_to_use = 8;
 	plat->tx_queues_to_use = 8;
-	plat->clk_ptp_rate = 200000000;
 	plat->use_phy_wol = 1;
 
 	plat->safety_feat_cfg->tsoee = 1;
@@ -617,6 +624,8 @@
 	plat->serdes_powerup = intel_serdes_powerup;
 	plat->serdes_powerdown = intel_serdes_powerdown;
 
+	plat->clk_ptp_rate = 204800000;
+
 	return ehl_common_data(pdev, plat);
 }
 
@@ -630,6 +639,8 @@
 	plat->bus_id = 1;
 	plat->phy_interface = PHY_INTERFACE_MODE_RGMII;
 
+	plat->clk_ptp_rate = 204800000;
+
 	return ehl_common_data(pdev, plat);
 }
 
@@ -646,6 +657,8 @@
 	plat->bus_id = 2;
 	plat->addr64 = 32;
 
+	plat->clk_ptp_rate = 200000000;
+
 	intel_mgbe_pse_crossts_adj(intel_priv, EHL_PSE_ART_MHZ);
 
 	return ehl_common_data(pdev, plat);
@@ -685,6 +698,8 @@
 	plat->bus_id = 3;
 	plat->addr64 = 32;
 
+	plat->clk_ptp_rate = 200000000;
+
 	intel_mgbe_pse_crossts_adj(intel_priv, EHL_PSE_ART_MHZ);
 
 	return ehl_common_data(pdev, plat);
@@ -720,7 +735,8 @@
 {
 	plat->rx_queues_to_use = 6;
 	plat->tx_queues_to_use = 4;
-	plat->clk_ptp_rate = 200000000;
+	plat->clk_ptp_rate = 204800000;
+	plat->speed_mode_2500 = intel_speed_mode_2500;
 
 	plat->safety_feat_cfg->tsoee = 1;
 	plat->safety_feat_cfg->mrxpee = 0;
@@ -740,7 +756,6 @@
 {
 	plat->bus_id = 1;
 	plat->phy_interface = PHY_INTERFACE_MODE_SGMII;
-	plat->speed_mode_2500 = intel_speed_mode_2500;
 	plat->serdes_powerup = intel_serdes_powerup;
 	plat->serdes_powerdown = intel_serdes_powerdown;
 	return tgl_common_data(pdev, plat);
@@ -755,7 +770,6 @@
 {
 	plat->bus_id = 2;
 	plat->phy_interface = PHY_INTERFACE_MODE_SGMII;
-	plat->speed_mode_2500 = intel_speed_mode_2500;
 	plat->serdes_powerup = intel_serdes_powerup;
 	plat->serdes_powerdown = intel_serdes_powerdown;
 	return tgl_common_data(pdev, plat);
@@ -1072,13 +1086,11 @@
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
 	if (ret) {
-		goto err_dvr_probe;
+		goto err_alloc_irq;
 	}
 
 	return 0;
 
-err_dvr_probe:
-	pci_free_irq_vectors(pdev);
 err_alloc_irq:
 	clk_disable_unprepare(plat->stmmac_clk);
 	clk_unregister_fixed_rate(plat->stmmac_clk);
@@ -1099,6 +1111,7 @@
 
 	stmmac_dvr_remove(&pdev->dev);
 
+	clk_disable_unprepare(priv->plat->stmmac_clk);
 	clk_unregister_fixed_rate(priv->plat->stmmac_clk);
 
 	pcim_iounmap_regions(pdev, BIT(0));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
@@ -35,6 +35,9 @@
 	/* Disable RX queues routing by default */
 	plat->rx_queues_cfg[0].pkt_route = 0x0;
 
+	plat->clk_ref_rate = 125000000;
+	plat->clk_ptp_rate = 125000000;
+
 	/* Default to phy auto-detection */
 	plat->phy_addr = -1;
 
@@ -51,7 +54,6 @@
 	struct stmmac_resources res;
 	struct device_node *np;
 	int ret, i, phy_mode;
-	bool mdio = false;
 
 	np = dev_of_node(&pdev->dev);
 
@@ -60,38 +62,33 @@
 		return -ENODEV;
 	}
 
-	if (!of_device_is_compatible(np, "loongson, pci-gmac")) {
-		pr_info("dwmac_loongson_pci: Incompatible OF node\n");
-		return -ENODEV;
-	}
-
 	plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
 	if (!plat)
 		return -ENOMEM;
 
-	if (plat->mdio_node) {
-		dev_err(&pdev->dev, "Found MDIO subnode\n");
-		mdio = true;
-	}
+	plat->mdio_bus_data = devm_kzalloc(&pdev->dev,
+					   sizeof(*plat->mdio_bus_data),
+					   GFP_KERNEL);
+	if (!plat->mdio_bus_data)
+		return -ENOMEM;
 
-	if (mdio) {
-		plat->mdio_bus_data = devm_kzalloc(&pdev->dev,
-						   sizeof(*plat->mdio_bus_data),
-						   GFP_KERNEL);
-		if (!plat->mdio_bus_data)
-			return -ENOMEM;
+	plat->mdio_node = of_get_child_by_name(np, "mdio");
+	if (plat->mdio_node) {
+		dev_info(&pdev->dev, "Found MDIO subnode\n");
 		plat->mdio_bus_data->needs_reset = true;
 	}
 
 	plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*plat->dma_cfg), GFP_KERNEL);
-	if (!plat->dma_cfg)
-		return -ENOMEM;
+	if (!plat->dma_cfg) {
+		ret = -ENOMEM;
+		goto err_put_node;
+	}
 
 	/* Enable pci device */
 	ret = pci_enable_device(pdev);
 	if (ret) {
 		dev_err(&pdev->dev, "%s: ERROR: failed to enable device\n", __func__);
-		return ret;
+		goto err_put_node;
 	}
 
 	/* Get the base address of device */
@@ -100,7 +97,7 @@
 			continue;
 		ret = pcim_iomap_regions(pdev, BIT(0), pci_name(pdev));
 		if (ret)
-			return ret;
+			goto err_disable_device;
 		break;
 	}
 
@@ -111,7 +108,8 @@
 	phy_mode = device_get_phy_mode(&pdev->dev);
 	if (phy_mode < 0) {
 		dev_err(&pdev->dev, "phy_mode not found\n");
-		return phy_mode;
+		ret = phy_mode;
+		goto err_disable_device;
 	}
 
 	plat->phy_interface = phy_mode;
@@ -128,6 +126,7 @@
 	if (res.irq < 0) {
 		dev_err(&pdev->dev, "IRQ macirq not found\n");
 		ret = -ENODEV;
+		goto err_disable_msi;
 	}
 
 	res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
@@ -140,15 +139,31 @@
 	if (res.lpi_irq < 0) {
 		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
 		ret = -ENODEV;
+		goto err_disable_msi;
 	}
 
-	return stmmac_dvr_probe(&pdev->dev, plat, &res);
+	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
+	if (ret)
+		goto err_disable_msi;
+
+	return ret;
+
+err_disable_msi:
+	pci_disable_msi(pdev);
+err_disable_device:
+	pci_disable_device(pdev);
+err_put_node:
+	of_node_put(plat->mdio_node);
+	return ret;
 }
 
 static void loongson_dwmac_remove(struct pci_dev *pdev)
 {
+	struct net_device *ndev = dev_get_drvdata(&pdev->dev);
+	struct stmmac_priv *priv = netdev_priv(ndev);
 	int i;
 
+	of_node_put(priv->plat->mdio_node);
 	stmmac_dvr_remove(&pdev->dev);
 
 	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
@@ -158,6 +173,7 @@
 		break;
 	}
 
+	pci_disable_msi(pdev);
 	pci_disable_device(pdev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -272,11 +272,9 @@
 	if (ret)
 		return ret;
 
-	devm_add_action_or_reset(dwmac->dev,
-				 (void(*)(void *))clk_disable_unprepare,
-				 dwmac->rgmii_tx_clk);
-
-	return 0;
+	return devm_add_action_or_reset(dwmac->dev,
+					(void(*)(void *))clk_disable_unprepare,
+					clk);
 }
 
 static int meson8b_init_rgmii_delays(struct meson8b_dwmac *dwmac)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
@@ -113,8 +113,10 @@
 	rgmii_writel(ethqos, temp, offset);
 }
 
-static void rgmii_dump(struct qcom_ethqos *ethqos)
+static void rgmii_dump(void *priv)
 {
+	struct qcom_ethqos *ethqos = priv;
+
 	dev_dbg(&ethqos->pdev->dev, "Rgmii register dump\n");
 	dev_dbg(&ethqos->pdev->dev, "RGMII_IO_MACRO_CONFIG: %x\n",
 		rgmii_readl(ethqos, RGMII_IO_MACRO_CONFIG));
@@ -499,16 +501,17 @@
 
 	plat_dat->bsp_priv = ethqos;
 	plat_dat->fix_mac_speed = ethqos_fix_mac_speed;
+	plat_dat->dump_debug_regs = rgmii_dump;
 	plat_dat->has_gmac4 = 1;
 	plat_dat->pmt = 1;
 	plat_dat->tso_en = of_property_read_bool(np, "snps,tso");
+	if (of_device_is_compatible(np, "qcom,qcs404-ethqos"))
+		plat_dat->rx_clk_runs_in_lpi = 1;
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (ret)
 		goto err_clk;
 
-	rgmii_dump(ethqos);
-
 	return ret;
 
 err_clk:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
@@ -33,6 +33,7 @@
 	void (*set_rgmii_speed)(struct rk_priv_data *bsp_priv, int speed);
 	void (*set_rmii_speed)(struct rk_priv_data *bsp_priv, int speed);
 	void (*integrated_phy_powerup)(struct rk_priv_data *bsp_priv);
+	bool regs_valid;
 	u32 regs[];
 };
 
@@ -1092,6 +1093,7 @@
 	.set_to_rmii = rk3568_set_to_rmii,
 	.set_rgmii_speed = rk3568_set_gmac_speed,
 	.set_rmii_speed = rk3568_set_gmac_speed,
+	.regs_valid = true,
 	.regs = {
 		0xfe2a0000, /* gmac0 */
 		0xfe010000, /* gmac1 */
@@ -1345,9 +1347,6 @@
 	int ret;
 	struct device *dev = &bsp_priv->pdev->dev;
 
-	if (!ldo)
-		return 0;
-
 	if (enable) {
 		ret = regulator_enable(ldo);
 		if (ret)
@@ -1383,7 +1382,7 @@
 	 * to be distinguished.
 	 */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (res) {
+	if (res && ops->regs_valid) {
 		int i = 0;
 
 		while (ops->regs[i]) {
@@ -1395,14 +1394,11 @@
 		}
 	}
 
-	bsp_priv->regulator = devm_regulator_get_optional(dev, "phy");
+	bsp_priv->regulator = devm_regulator_get(dev, "phy");
 	if (IS_ERR(bsp_priv->regulator)) {
-		if (PTR_ERR(bsp_priv->regulator) == -EPROBE_DEFER) {
-			dev_err(dev, "phy regulator is not available yet, deferred probing\n");
-			return ERR_PTR(-EPROBE_DEFER);
-		}
-		dev_err(dev, "no regulator found\n");
-		bsp_priv->regulator = NULL;
+		ret = PTR_ERR(bsp_priv->regulator);
+		dev_err_probe(dev, ret, "failed to get phy regulator\n");
+		return ERR_PTR(ret);
 	}
 
 	ret = of_property_read_string(dev->of_node, "clock_in_out", &strings);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
@@ -18,9 +18,6 @@
 
 #include "altr_tse_pcs.h"
 
-#define SGMII_ADAPTER_CTRL_REG                          0x00
-#define SGMII_ADAPTER_DISABLE                           0x0001
-
 #define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII 0x0
 #define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII 0x1
 #define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII 0x2
@@ -62,14 +59,13 @@
 {
 	struct socfpga_dwmac *dwmac = (struct socfpga_dwmac *)priv;
 	void __iomem *splitter_base = dwmac->splitter_base;
-	void __iomem *tse_pcs_base = dwmac->pcs.tse_pcs_base;
 	void __iomem *sgmii_adapter_base = dwmac->pcs.sgmii_adapter_base;
 	struct device *dev = dwmac->dev;
 	struct net_device *ndev = dev_get_drvdata(dev);
 	struct phy_device *phy_dev = ndev->phydev;
 	u32 val;
 
-	if ((tse_pcs_base) && (sgmii_adapter_base))
+	if (sgmii_adapter_base)
 		writew(SGMII_ADAPTER_DISABLE,
 		       sgmii_adapter_base + SGMII_ADAPTER_CTRL_REG);
 
@@ -93,8 +89,11 @@
 		writel(val, splitter_base + EMAC_SPLITTER_CTRL_REG);
 	}
 
-	if (tse_pcs_base && sgmii_adapter_base)
+	if (phy_dev && sgmii_adapter_base) {
+		writew(SGMII_ADAPTER_ENABLE,
+		       sgmii_adapter_base + SGMII_ADAPTER_CTRL_REG);
 		tse_pcs_fix_mac_speed(&dwmac->pcs, phy_dev, speed);
+	}
 }
 
 static int socfpga_dwmac_parse_data(struct socfpga_dwmac *dwmac, struct device *dev)
@@ -427,6 +426,8 @@
 	plat_dat->bsp_priv = dwmac;
 	plat_dat->fix_mac_speed = socfpga_dwmac_fix_mac_speed;
 
+	plat_dat->riwt_off = 1;
+
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (ret)
 		goto err_remove_config_dt;
@@ -485,8 +486,28 @@
 }
 #endif /* CONFIG_PM_SLEEP */
 
-static SIMPLE_DEV_PM_OPS(socfpga_dwmac_pm_ops, stmmac_suspend,
-					       socfpga_dwmac_resume);
+static int __maybe_unused socfpga_dwmac_runtime_suspend(struct device *dev)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct stmmac_priv *priv = netdev_priv(ndev);
+
+	stmmac_bus_clks_config(priv, false);
+
+	return 0;
+}
+
+static int __maybe_unused socfpga_dwmac_runtime_resume(struct device *dev)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct stmmac_priv *priv = netdev_priv(ndev);
+
+	return stmmac_bus_clks_config(priv, true);
+}
+
+static const struct dev_pm_ops socfpga_dwmac_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(stmmac_suspend, socfpga_dwmac_resume)
+	SET_RUNTIME_PM_OPS(socfpga_dwmac_runtime_suspend, socfpga_dwmac_runtime_resume, NULL)
+};
 
 static const struct socfpga_dwmac_ops socfpga_gen5_ops = {
 	.set_phy_mode = socfpga_gen5_set_phy_mode,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -105,6 +105,7 @@
 	int (*parse_data)(struct stm32_dwmac *dwmac,
 			  struct device *dev);
 	u32 syscfg_eth_mask;
+	bool clk_rx_enable_in_suspend;
 };
 
 static int stm32_dwmac_init(struct plat_stmmacenet_data *plat_dat)
@@ -122,7 +123,8 @@
 	if (ret)
 		return ret;
 
-	if (!dwmac->dev->power.is_suspended) {
+	if (!dwmac->ops->clk_rx_enable_in_suspend ||
+	    !dwmac->dev->power.is_suspended) {
 		ret = clk_prepare_enable(dwmac->clk_rx);
 		if (ret) {
 			clk_disable_unprepare(dwmac->clk_tx);
@@ -515,7 +517,8 @@
 	.suspend = stm32mp1_suspend,
 	.resume = stm32mp1_resume,
 	.parse_data = stm32mp1_parse_data,
-	.syscfg_eth_mask = SYSCFG_MP1_ETH_MASK
+	.syscfg_eth_mask = SYSCFG_MP1_ETH_MASK,
+	.clk_rx_enable_in_suspend = true
 };
 
 static const struct of_device_id stm32_dwmac_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -634,7 +634,7 @@
  * If addr is NULL, clear the slot
  */
 static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw,
-				      unsigned char *addr,
+				      const unsigned char *addr,
 				      unsigned int reg_n)
 {
 	void __iomem *ioaddr = hw->pcsr;
@@ -756,7 +756,7 @@
 
 	if (err) {
 		dev_err(priv->device, "EMAC reset timeout\n");
-		return -EFAULT;
+		return err;
 	}
 	return 0;
 }
@@ -916,6 +916,7 @@
 
 	ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn,
 			    &gmac->mux_handle, priv, priv->mii);
+	of_node_put(mdio_mux);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
@@ -22,21 +22,21 @@
 #define ETHER_CLK_SEL_RMII_CLK_EN BIT(2)
 #define ETHER_CLK_SEL_RMII_CLK_RST BIT(3)
 #define ETHER_CLK_SEL_DIV_SEL_2 BIT(4)
-#define ETHER_CLK_SEL_DIV_SEL_20 BIT(0)
+#define ETHER_CLK_SEL_DIV_SEL_20 0
 #define ETHER_CLK_SEL_FREQ_SEL_125M	(BIT(9) | BIT(8))
 #define ETHER_CLK_SEL_FREQ_SEL_50M	BIT(9)
 #define ETHER_CLK_SEL_FREQ_SEL_25M	BIT(8)
-#define ETHER_CLK_SEL_FREQ_SEL_2P5M	BIT(0)
-#define ETHER_CLK_SEL_TX_CLK_EXT_SEL_IN BIT(0)
+#define ETHER_CLK_SEL_FREQ_SEL_2P5M	0
+#define ETHER_CLK_SEL_TX_CLK_EXT_SEL_IN 0
 #define ETHER_CLK_SEL_TX_CLK_EXT_SEL_TXC BIT(10)
 #define ETHER_CLK_SEL_TX_CLK_EXT_SEL_DIV BIT(11)
-#define ETHER_CLK_SEL_RX_CLK_EXT_SEL_IN  BIT(0)
+#define ETHER_CLK_SEL_RX_CLK_EXT_SEL_IN  0
 #define ETHER_CLK_SEL_RX_CLK_EXT_SEL_RXC BIT(12)
 #define ETHER_CLK_SEL_RX_CLK_EXT_SEL_DIV BIT(13)
-#define ETHER_CLK_SEL_TX_CLK_O_TX_I	 BIT(0)
+#define ETHER_CLK_SEL_TX_CLK_O_TX_I	 0
 #define ETHER_CLK_SEL_TX_CLK_O_RMII_I	 BIT(14)
 #define ETHER_CLK_SEL_TX_O_E_N_IN	 BIT(15)
-#define ETHER_CLK_SEL_RMII_CLK_SEL_IN	 BIT(0)
+#define ETHER_CLK_SEL_RMII_CLK_SEL_IN	 0
 #define ETHER_CLK_SEL_RMII_CLK_SEL_RX_C	 BIT(16)
 
 #define ETHER_CLK_SEL_RX_TX_CLK_EN (ETHER_CLK_SEL_RX_CLK_EN | ETHER_CLK_SEL_TX_CLK_EN)
@@ -49,13 +49,15 @@
 	void __iomem *reg;
 	u32 phy_intf_sel;
 	struct clk *phy_ref_clk;
+	struct device *dev;
 	spinlock_t lock; /* lock to protect register update */
 };
 
 static void visconti_eth_fix_mac_speed(void *priv, unsigned int speed)
 {
 	struct visconti_eth *dwmac = priv;
-	unsigned int val, clk_sel_val;
+	struct net_device *netdev = dev_get_drvdata(dwmac->dev);
+	unsigned int val, clk_sel_val = 0;
 	unsigned long flags;
 
 	spin_lock_irqsave(&dwmac->lock, flags);
@@ -85,7 +87,9 @@
 		break;
 	default:
 		/* No bit control */
-		break;
+		netdev_err(netdev, "Unsupported speed request (%d)", speed);
+		spin_unlock_irqrestore(&dwmac->lock, flags);
+		return;
 	}
 
 	writel(val, dwmac->reg + MAC_CTRL_REG);
@@ -96,31 +100,41 @@
 	val |= ETHER_CLK_SEL_TX_O_E_N_IN;
 	writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
 
+	/* Set Clock-Mux, Start clock, Set TX_O direction */
 	switch (dwmac->phy_intf_sel) {
 	case ETHER_CONFIG_INTF_RGMII:
 		val = clk_sel_val | ETHER_CLK_SEL_RX_CLK_EXT_SEL_RXC;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
+
+		val |= ETHER_CLK_SEL_RX_TX_CLK_EN;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
+
+		val &= ~ETHER_CLK_SEL_TX_O_E_N_IN;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
 		break;
 	case ETHER_CONFIG_INTF_RMII:
 		val = clk_sel_val | ETHER_CLK_SEL_RX_CLK_EXT_SEL_DIV |
-			ETHER_CLK_SEL_TX_CLK_EXT_SEL_TXC | ETHER_CLK_SEL_TX_O_E_N_IN |
+			ETHER_CLK_SEL_TX_CLK_EXT_SEL_DIV | ETHER_CLK_SEL_TX_O_E_N_IN |
 			ETHER_CLK_SEL_RMII_CLK_SEL_RX_C;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
+
+		val |= ETHER_CLK_SEL_RMII_CLK_RST;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
+
+		val |= ETHER_CLK_SEL_RMII_CLK_EN | ETHER_CLK_SEL_RX_TX_CLK_EN;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
 		break;
 	case ETHER_CONFIG_INTF_MII:
 	default:
 		val = clk_sel_val | ETHER_CLK_SEL_RX_CLK_EXT_SEL_RXC |
-			ETHER_CLK_SEL_TX_CLK_EXT_SEL_DIV | ETHER_CLK_SEL_TX_O_E_N_IN |
-			ETHER_CLK_SEL_RMII_CLK_EN;
+			ETHER_CLK_SEL_TX_CLK_EXT_SEL_TXC | ETHER_CLK_SEL_TX_O_E_N_IN;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
+
+		val |= ETHER_CLK_SEL_RX_TX_CLK_EN;
+		writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
 		break;
 	}
 
-	/* Start clock */
-	writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
-	val |= ETHER_CLK_SEL_RX_TX_CLK_EN;
-	writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
-
-	val &= ~ETHER_CLK_SEL_TX_O_E_N_IN;
-	writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL);
-
 	spin_unlock_irqrestore(&dwmac->lock, flags);
 }
 
@@ -220,6 +234,7 @@
 
 	spin_lock_init(&dwmac->lock);
 	dwmac->reg = stmmac_res.addr;
+	dwmac->dev = &pdev->dev;
 	plat_dat->bsp_priv = dwmac;
 	plat_dat->fix_mac_speed = visconti_eth_fix_mac_speed;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac100.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac100.h
@@ -56,7 +56,7 @@
 #define MAC_CONTROL_TE		0x00000008	/* Transmitter Enable */
 #define MAC_CONTROL_RE		0x00000004	/* Receiver Enable */
 
-#define MAC_CORE_INIT (MAC_CONTROL_HBD | MAC_CONTROL_ASTP)
+#define MAC_CORE_INIT (MAC_CONTROL_HBD)
 
 /* MAC FLOW CTRL defines */
 #define MAC_FLOW_CTRL_PT_MASK	0xffff0000	/* Pause Time Mask */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
@@ -126,7 +126,7 @@
 #define GMAC_CONTROL_TE		0x00000008	/* Transmitter Enable */
 #define GMAC_CONTROL_RE		0x00000004	/* Receiver Enable */
 
-#define GMAC_CORE_INIT (GMAC_CONTROL_JD | GMAC_CONTROL_PS | GMAC_CONTROL_ACS | \
+#define GMAC_CORE_INIT (GMAC_CONTROL_JD | GMAC_CONTROL_PS | \
 			GMAC_CONTROL_BE | GMAC_CONTROL_DCRS)
 
 /* GMAC Frame Filter defines */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
@@ -15,7 +15,6 @@
 #include <linux/crc32.h>
 #include <linux/slab.h>
 #include <linux/ethtool.h>
-#include <net/dsa.h>
 #include <asm/io.h>
 #include "stmmac.h"
 #include "stmmac_pcs.h"
@@ -24,7 +23,6 @@
 static void dwmac1000_core_init(struct mac_device_info *hw,
 				struct net_device *dev)
 {
-	struct stmmac_priv *priv = netdev_priv(dev);
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value = readl(ioaddr + GMAC_CONTROL);
 	int mtu = dev->mtu;
@@ -32,13 +30,6 @@
 	/* Configure GMAC core */
 	value |= GMAC_CORE_INIT;
 
-	/* Clear ACS bit because Ethernet switch tagging formats such as
-	 * Broadcom tags can look like invalid LLC/SNAP packets and cause the
-	 * hardware to truncate packets on reception.
-	 */
-	if (netdev_uses_dsa(dev) || !priv->plat->enh_desc)
-		value &= ~GMAC_CONTROL_ACS;
-
 	if (mtu > 1500)
 		value |= GMAC_CONTROL_2K;
 	if (mtu > 2000)
@@ -104,7 +95,7 @@
 }
 
 static void dwmac1000_set_umac_addr(struct mac_device_info *hw,
-				    unsigned char *addr,
+				    const unsigned char *addr,
 				    unsigned int reg_n)
 {
 	void __iomem *ioaddr = hw->pcsr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac100_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac100_core.c
@@ -15,7 +15,6 @@
 *******************************************************************************/
 
 #include <linux/crc32.h>
-#include <net/dsa.h>
 #include <asm/io.h>
 #include "stmmac.h"
 #include "dwmac100.h"
@@ -28,13 +27,6 @@
 
 	value |= MAC_CORE_INIT;
 
-	/* Clear ASTP bit because Ethernet switch tagging formats such as
-	 * Broadcom tags can look like invalid LLC/SNAP packets and cause the
-	 * hardware to truncate packets on reception.
-	 */
-	if (netdev_uses_dsa(dev))
-		value &= ~MAC_CONTROL_ASTP;
-
 	writel(value, ioaddr + MAC_CONTROL);
 
 #ifdef STMMAC_VLAN_TAG_USED
@@ -68,7 +60,7 @@
 }
 
 static void dwmac100_set_umac_addr(struct mac_device_info *hw,
-				   unsigned char *addr,
+				   const unsigned char *addr,
 				   unsigned int reg_n)
 {
 	void __iomem *ioaddr = hw->pcsr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
@@ -150,7 +150,8 @@
 #define	GMAC_PCS_IRQ_DEFAULT	(GMAC_INT_RGSMIIS | GMAC_INT_PCS_LINK |	\
 				 GMAC_INT_PCS_ANE)
 
-#define	GMAC_INT_DEFAULT_ENABLE	(GMAC_INT_PMT_EN | GMAC_INT_LPI_EN)
+#define	GMAC_INT_DEFAULT_ENABLE	(GMAC_INT_PMT_EN | GMAC_INT_LPI_EN | \
+				 GMAC_INT_TSIE)
 
 enum dwmac4_irq_status {
 	time_stamp_irq = 0x00001000,
@@ -180,6 +181,7 @@
 #define GMAC4_LPI_CTRL_STATUS	0xd0
 #define GMAC4_LPI_TIMER_CTRL	0xd4
 #define GMAC4_LPI_ENTRY_TIMER	0xd8
+#define GMAC4_MAC_ONEUS_TIC_COUNTER	0xdc
 
 /* LPI control and status defines */
 #define GMAC4_LPI_CTRL_STATUS_LPITCSE	BIT(21)	/* LPI Tx Clock Stop Enable */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
@@ -14,7 +14,7 @@
 #include <linux/slab.h>
 #include <linux/ethtool.h>
 #include <linux/io.h>
-#include <net/dsa.h>
+#include <linux/iopoll.h>
 #include "stmmac.h"
 #include "stmmac_pcs.h"
 #include "dwmac4.h"
@@ -23,8 +23,10 @@
 static void dwmac4_core_init(struct mac_device_info *hw,
 			     struct net_device *dev)
 {
+	struct stmmac_priv *priv = netdev_priv(dev);
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value = readl(ioaddr + GMAC_CONFIG);
+	u32 clk_rate;
 
 	value |= GMAC_CORE_INIT;
 
@@ -47,6 +49,10 @@
 
 	writel(value, ioaddr + GMAC_CONFIG);
 
+	/* Configure LPI 1us counter to number of CSR clock ticks in 1us - 1 */
+	clk_rate = clk_get_rate(priv->plat->stmmac_clk);
+	writel((clk_rate / 1000000) - 1, ioaddr + GMAC4_MAC_ONEUS_TIC_COUNTER);
+
 	/* Enable GMAC interrupts */
 	value = GMAC_INT_DEFAULT_ENABLE;
 
@@ -58,6 +64,9 @@
 		value |= GMAC_INT_FPE_EN;
 
 	writel(value, ioaddr + GMAC_INT_EN);
+
+	if (GMAC_INT_DEFAULT_ENABLE & GMAC_INT_TSIE)
+		init_waitqueue_head(&priv->tstamp_busy_wait);
 }
 
 static void dwmac4_rx_queue_enable(struct mac_device_info *hw,
@@ -79,19 +88,41 @@
 				     u32 prio, u32 queue)
 {
 	void __iomem *ioaddr = hw->pcsr;
-	u32 base_register;
-	u32 value;
+	u32 clear_mask = 0;
+	u32 ctrl2, ctrl3;
+	int i;
 
-	base_register = (queue < 4) ? GMAC_RXQ_CTRL2 : GMAC_RXQ_CTRL3;
-	if (queue >= 4)
-		queue -= 4;
+	ctrl2 = readl(ioaddr + GMAC_RXQ_CTRL2);
+	ctrl3 = readl(ioaddr + GMAC_RXQ_CTRL3);
 
-	value = readl(ioaddr + base_register);
+	/* The software must ensure that the same priority
+	 * is not mapped to multiple Rx queues
+	 */
+	for (i = 0; i < 4; i++)
+		clear_mask |= ((prio << GMAC_RXQCTRL_PSRQX_SHIFT(i)) &
+						GMAC_RXQCTRL_PSRQX_MASK(i));
+
+	ctrl2 &= ~clear_mask;
+	ctrl3 &= ~clear_mask;
 
-	value &= ~GMAC_RXQCTRL_PSRQX_MASK(queue);
-	value |= (prio << GMAC_RXQCTRL_PSRQX_SHIFT(queue)) &
+	/* First assign new priorities to a queue, then
+	 * clear them from others queues
+	 */
+	if (queue < 4) {
+		ctrl2 |= (prio << GMAC_RXQCTRL_PSRQX_SHIFT(queue)) &
 						GMAC_RXQCTRL_PSRQX_MASK(queue);
-	writel(value, ioaddr + base_register);
+
+		writel(ctrl2, ioaddr + GMAC_RXQ_CTRL2);
+		writel(ctrl3, ioaddr + GMAC_RXQ_CTRL3);
+	} else {
+		queue -= 4;
+
+		ctrl3 |= (prio << GMAC_RXQCTRL_PSRQX_SHIFT(queue)) &
+						GMAC_RXQCTRL_PSRQX_MASK(queue);
+
+		writel(ctrl3, ioaddr + GMAC_RXQ_CTRL3);
+		writel(ctrl2, ioaddr + GMAC_RXQ_CTRL2);
+	}
 }
 
 static void dwmac4_tx_queue_priority(struct mac_device_info *hw,
@@ -219,6 +250,9 @@
 	if (queue == 0 || queue == 4) {
 		value &= ~MTL_RXQ_DMA_Q04MDMACH_MASK;
 		value |= MTL_RXQ_DMA_Q04MDMACH(chan);
+	} else if (queue > 4) {
+		value &= ~MTL_RXQ_DMA_QXMDMACH_MASK(queue - 4);
+		value |= MTL_RXQ_DMA_QXMDMACH(chan, queue - 4);
 	} else {
 		value &= ~MTL_RXQ_DMA_QXMDMACH_MASK(queue);
 		value |= MTL_RXQ_DMA_QXMDMACH(chan, queue);
@@ -322,7 +356,7 @@
 }
 
 static void dwmac4_set_umac_addr(struct mac_device_info *hw,
-				 unsigned char *addr, unsigned int reg_n)
+				 const unsigned char *addr, unsigned int reg_n)
 {
 	void __iomem *ioaddr = hw->pcsr;
 
@@ -436,7 +470,7 @@
 				    u8 index, u32 data)
 {
 	void __iomem *ioaddr = (void __iomem *)dev->base_addr;
-	int i, timeout = 10;
+	int ret;
 	u32 val;
 
 	if (index >= hw->num_vlan)
@@ -452,16 +486,15 @@
 
 	writel(val, ioaddr + GMAC_VLAN_TAG);
 
-	for (i = 0; i < timeout; i++) {
-		val = readl(ioaddr + GMAC_VLAN_TAG);
-		if (!(val & GMAC_VLAN_TAG_CTRL_OB))
-			return 0;
-		udelay(1);
+	ret = readl_poll_timeout(ioaddr + GMAC_VLAN_TAG, val,
+				 !(val & GMAC_VLAN_TAG_CTRL_OB),
+				 1000, 500000);
+	if (ret) {
+		netdev_err(dev, "Timeout accessing MAC_VLAN_Tag_Filter\n");
+		return -EBUSY;
 	}
 
-	netdev_err(dev, "Timeout accessing MAC_VLAN_Tag_Filter\n");
-
-	return -EBUSY;
+	return 0;
 }
 
 static int dwmac4_add_hw_vlan_rx_fltr(struct net_device *dev,
@@ -475,12 +508,6 @@
 	if (vid > 4095)
 		return -EINVAL;
 
-	if (hw->promisc) {
-		netdev_err(dev,
-			   "Adding VLAN in promisc mode not supported\n");
-		return -EPERM;
-	}
-
 	/* Single Rx VLAN Filter */
 	if (hw->num_vlan == 1) {
 		/* For single VLAN filter, VID 0 means VLAN promiscuous */
@@ -530,12 +557,6 @@
 {
 	int i, ret = 0;
 
-	if (hw->promisc) {
-		netdev_err(dev,
-			   "Deleting VLAN in promisc mode not supported\n");
-		return -EPERM;
-	}
-
 	/* Single Rx VLAN Filter */
 	if (hw->num_vlan == 1) {
 		if ((hw->vlan_filter[0] & GMAC_VLAN_TAG_VID) == vid) {
@@ -560,39 +581,6 @@
 	return ret;
 }
 
-static void dwmac4_vlan_promisc_enable(struct net_device *dev,
-				       struct mac_device_info *hw)
-{
-	void __iomem *ioaddr = hw->pcsr;
-	u32 value;
-	u32 hash;
-	u32 val;
-	int i;
-
-	/* Single Rx VLAN Filter */
-	if (hw->num_vlan == 1) {
-		dwmac4_write_single_vlan(dev, 0);
-		return;
-	}
-
-	/* Extended Rx VLAN Filter Enable */
-	for (i = 0; i < hw->num_vlan; i++) {
-		if (hw->vlan_filter[i] & GMAC_VLAN_TAG_DATA_VEN) {
-			val = hw->vlan_filter[i] & ~GMAC_VLAN_TAG_DATA_VEN;
-			dwmac4_write_vlan_filter(dev, hw, i, val);
-		}
-	}
-
-	hash = readl(ioaddr + GMAC_VLAN_HASH_TABLE);
-	if (hash & GMAC_VLAN_VLHT) {
-		value = readl(ioaddr + GMAC_VLAN_TAG);
-		if (value & GMAC_VLAN_VTHM) {
-			value &= ~GMAC_VLAN_VTHM;
-			writel(value, ioaddr + GMAC_VLAN_TAG);
-		}
-	}
-}
-
 static void dwmac4_restore_hw_vlan_rx_fltr(struct net_device *dev,
 					   struct mac_device_info *hw)
 {
@@ -712,22 +700,12 @@
 	}
 
 	/* VLAN filtering */
-	if (dev->features & NETIF_F_HW_VLAN_CTAG_FILTER)
+	if (dev->flags & IFF_PROMISC && !hw->vlan_fail_q_en)
+		value &= ~GMAC_PACKET_FILTER_VTFE;
+	else if (dev->features & NETIF_F_HW_VLAN_CTAG_FILTER)
 		value |= GMAC_PACKET_FILTER_VTFE;
 
 	writel(value, ioaddr + GMAC_PACKET_FILTER);
-
-	if (dev->flags & IFF_PROMISC && !hw->vlan_fail_q_en) {
-		if (!hw->promisc) {
-			hw->promisc = 1;
-			dwmac4_vlan_promisc_enable(dev, hw);
-		}
-	} else {
-		if (hw->promisc) {
-			hw->promisc = 0;
-			dwmac4_restore_hw_vlan_rx_fltr(dev, hw);
-		}
-	}
 }
 
 static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,
@@ -742,6 +720,8 @@
 	if (fc & FLOW_RX) {
 		pr_debug("\tReceive Flow-Control ON\n");
 		flow |= GMAC_RX_FLOW_CTRL_RFE;
+	} else {
+		pr_debug("\tReceive Flow-Control OFF\n");
 	}
 	writel(flow, ioaddr + GMAC_RX_FLOW_CTRL);
 
@@ -991,7 +971,7 @@
 }
 
 static void dwmac4_update_vlan_hash(struct mac_device_info *hw, u32 hash,
-				    __le16 perfect_match, bool is_double)
+				    u16 perfect_match, bool is_double)
 {
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac4_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac4_lib.c
@@ -187,7 +187,7 @@
 	return ret;
 }
 
-void stmmac_dwmac4_set_mac_addr(void __iomem *ioaddr, u8 addr[6],
+void stmmac_dwmac4_set_mac_addr(void __iomem *ioaddr, const u8 addr[6],
 				unsigned int high, unsigned int low)
 {
 	unsigned long data;
@@ -207,13 +207,15 @@
 void stmmac_dwmac4_set_mac(void __iomem *ioaddr, bool enable)
 {
 	u32 value = readl(ioaddr + GMAC_CONFIG);
+	u32 old_val = value;
 
 	if (enable)
 		value |= GMAC_CONFIG_RE | GMAC_CONFIG_TE;
 	else
 		value &= ~(GMAC_CONFIG_TE | GMAC_CONFIG_RE);
 
-	writel(value, ioaddr + GMAC_CONFIG);
+	if (value != old_val)
+		writel(value, ioaddr + GMAC_CONFIG);
 }
 
 void stmmac_dwmac4_get_mac_addr(void __iomem *ioaddr, unsigned char *addr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac5.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac5.c
@@ -186,11 +186,25 @@
 int dwmac5_safety_feat_config(void __iomem *ioaddr, unsigned int asp,
 			      struct stmmac_safety_feature_cfg *safety_feat_cfg)
 {
+	struct stmmac_safety_feature_cfg all_safety_feats = {
+		.tsoee = 1,
+		.mrxpee = 1,
+		.mestee = 1,
+		.mrxee = 1,
+		.mtxee = 1,
+		.epsi = 1,
+		.edpp = 1,
+		.prtyen = 1,
+		.tmouten = 1,
+	};
 	u32 value;
 
 	if (!asp)
 		return -EINVAL;
 
+	if (!safety_feat_cfg)
+		safety_feat_cfg = &all_safety_feats;
+
 	/* 1. Enable Safety Features */
 	value = readl(ioaddr + MTL_ECC_CONTROL);
 	value |= MEEAO; /* MTL ECC Error Addr Status Override */
@@ -527,9 +541,9 @@
 		return 0;
 	}
 
-	val |= PPSCMDx(index, 0x2);
 	val |= TRGTMODSELx(index, 0x2);
 	val |= PPSEN0;
+	writel(val, ioaddr + MAC_PPS_CONTROL);
 
 	writel(cfg->start.tv_sec, ioaddr + MAC_PPSx_TARGET_TIME_SEC(index));
 
@@ -554,6 +568,7 @@
 	writel(period - 1, ioaddr + MAC_PPSx_WIDTH(index));
 
 	/* Finally, activate it */
+	val |= PPSCMDx(index, 0x2);
 	writel(val, ioaddr + MAC_PPS_CONTROL);
 	return 0;
 }
@@ -695,28 +710,22 @@
 	}
 }
 
-void dwmac5_fpe_configure(void __iomem *ioaddr, u32 num_txq, u32 num_rxq,
+void dwmac5_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
+			  u32 num_txq, u32 num_rxq,
 			  bool enable)
 {
 	u32 value;
 
-	if (!enable) {
-		value = readl(ioaddr + MAC_FPE_CTRL_STS);
-
-		value &= ~EFPE;
-
-		writel(value, ioaddr + MAC_FPE_CTRL_STS);
-		return;
+	if (enable) {
+		cfg->fpe_csr = EFPE;
+		value = readl(ioaddr + GMAC_RXQ_CTRL1);
+		value &= ~GMAC_RXQCTRL_FPRQ;
+		value |= (num_rxq - 1) << GMAC_RXQCTRL_FPRQ_SHIFT;
+		writel(value, ioaddr + GMAC_RXQ_CTRL1);
+	} else {
+		cfg->fpe_csr = 0;
 	}
-
-	value = readl(ioaddr + GMAC_RXQ_CTRL1);
-	value &= ~GMAC_RXQCTRL_FPRQ;
-	value |= (num_rxq - 1) << GMAC_RXQCTRL_FPRQ_SHIFT;
-	writel(value, ioaddr + GMAC_RXQ_CTRL1);
-
-	value = readl(ioaddr + MAC_FPE_CTRL_STS);
-	value |= EFPE;
-	writel(value, ioaddr + MAC_FPE_CTRL_STS);
+	writel(cfg->fpe_csr, ioaddr + MAC_FPE_CTRL_STS);
 }
 
 int dwmac5_fpe_irq_status(void __iomem *ioaddr, struct net_device *dev)
@@ -726,6 +735,9 @@
 
 	status = FPE_EVENT_UNKNOWN;
 
+	/* Reads from the MAC_FPE_CTRL_STS register should only be performed
+	 * here, since the status flags of MAC_FPE_CTRL_STS are "clear on read"
+	 */
 	value = readl(ioaddr + MAC_FPE_CTRL_STS);
 
 	if (value & TRSP) {
@@ -751,19 +763,15 @@
 	return status;
 }
 
-void dwmac5_fpe_send_mpacket(void __iomem *ioaddr, enum stmmac_mpacket_type type)
+void dwmac5_fpe_send_mpacket(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
+			     enum stmmac_mpacket_type type)
 {
-	u32 value;
+	u32 value = cfg->fpe_csr;
 
-	value = readl(ioaddr + MAC_FPE_CTRL_STS);
-
-	if (type == MPACKET_VERIFY) {
-		value &= ~SRSP;
+	if (type == MPACKET_VERIFY)
 		value |= SVER;
-	} else {
-		value &= ~SVER;
+	else if (type == MPACKET_RESPONSE)
 		value |= SRSP;
-	}
 
 	writel(value, ioaddr + MAC_FPE_CTRL_STS);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac5.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac5.h
@@ -153,9 +153,11 @@
 			 unsigned int ptp_rate);
 void dwmac5_est_irq_status(void __iomem *ioaddr, struct net_device *dev,
 			   struct stmmac_extra_stats *x, u32 txqcnt);
-void dwmac5_fpe_configure(void __iomem *ioaddr, u32 num_txq, u32 num_rxq,
+void dwmac5_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
+			  u32 num_txq, u32 num_rxq,
 			  bool enable);
 void dwmac5_fpe_send_mpacket(void __iomem *ioaddr,
+			     struct stmmac_fpe_cfg *cfg,
 			     enum stmmac_mpacket_type type);
 int dwmac5_fpe_irq_status(void __iomem *ioaddr, struct net_device *dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
@@ -150,6 +150,7 @@
 
 #define NUM_DWMAC100_DMA_REGS	9
 #define NUM_DWMAC1000_DMA_REGS	23
+#define NUM_DWMAC4_DMA_REGS	27
 
 void dwmac_enable_dma_transmission(void __iomem *ioaddr);
 void dwmac_enable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c
@@ -239,7 +239,7 @@
 	do {} while ((readl(ioaddr + DMA_CONTROL) & DMA_CONTROL_FTF));
 }
 
-void stmmac_set_mac_addr(void __iomem *ioaddr, u8 addr[6],
+void stmmac_set_mac_addr(void __iomem *ioaddr, const u8 addr[6],
 			 unsigned int high, unsigned int low)
 {
 	unsigned long data;
@@ -258,14 +258,18 @@
 /* Enable disable MAC RX/TX */
 void stmmac_set_mac(void __iomem *ioaddr, bool enable)
 {
-	u32 value = readl(ioaddr + MAC_CTRL_REG);
+	u32 old_val, value;
+
+	old_val = readl(ioaddr + MAC_CTRL_REG);
+	value = old_val;
 
 	if (enable)
 		value |= MAC_ENABLE_RX | MAC_ENABLE_TX;
 	else
 		value &= ~(MAC_ENABLE_TX | MAC_ENABLE_RX);
 
-	writel(value, ioaddr + MAC_CTRL_REG);
+	if (value != old_val)
+		writel(value, ioaddr + MAC_CTRL_REG);
 }
 
 void stmmac_get_mac_addr(void __iomem *ioaddr, unsigned char *addr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
@@ -222,7 +222,7 @@
 	((val) << XGMAC_PPS_MINIDX(x))
 #define XGMAC_PPSCMD_START		0x2
 #define XGMAC_PPSCMD_STOP		0x5
-#define XGMAC_PPSEN0			BIT(4)
+#define XGMAC_PPSENx(x)			BIT(4 + (x) * 8)
 #define XGMAC_PPSx_TARGET_TIME_SEC(x)	(0x00000d80 + (x) * 0x10)
 #define XGMAC_PPSx_TARGET_TIME_NSEC(x)	(0x00000d84 + (x) * 0x10)
 #define XGMAC_TRGTBUSY0			BIT(31)
@@ -282,6 +282,8 @@
 #define XGMAC_RXCEIE			BIT(4)
 #define XGMAC_TXCEIE			BIT(0)
 #define XGMAC_MTL_ECC_INT_STATUS	0x000010cc
+#define XGMAC_MTL_DPP_CONTROL		0x000010e0
+#define XGMAC_DPP_DISABLE		BIT(0)
 #define XGMAC_MTL_TXQ_OPMODE(x)		(0x00001100 + (0x80 * (x)))
 #define XGMAC_TQS			GENMASK(25, 16)
 #define XGMAC_TQS_SHIFT			16
@@ -364,6 +366,7 @@
 #define XGMAC_DCEIE			BIT(1)
 #define XGMAC_TCEIE			BIT(0)
 #define XGMAC_DMA_ECC_INT_STATUS	0x0000306c
+#define XGMAC_DMA_DPP_INT_STATUS	0x00003074
 #define XGMAC_DMA_CH_CONTROL(x)		(0x00003100 + (0x80 * (x)))
 #define XGMAC_SPH			BIT(24)
 #define XGMAC_PBLx8			BIT(16)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
@@ -97,17 +97,41 @@
 				   u32 queue)
 {
 	void __iomem *ioaddr = hw->pcsr;
-	u32 value, reg;
+	u32 clear_mask = 0;
+	u32 ctrl2, ctrl3;
+	int i;
 
-	reg = (queue < 4) ? XGMAC_RXQ_CTRL2 : XGMAC_RXQ_CTRL3;
-	if (queue >= 4)
+	ctrl2 = readl(ioaddr + XGMAC_RXQ_CTRL2);
+	ctrl3 = readl(ioaddr + XGMAC_RXQ_CTRL3);
+
+	/* The software must ensure that the same priority
+	 * is not mapped to multiple Rx queues
+	 */
+	for (i = 0; i < 4; i++)
+		clear_mask |= ((prio << XGMAC_PSRQ_SHIFT(i)) &
+						XGMAC_PSRQ(i));
+
+	ctrl2 &= ~clear_mask;
+	ctrl3 &= ~clear_mask;
+
+	/* First assign new priorities to a queue, then
+	 * clear them from others queues
+	 */
+	if (queue < 4) {
+		ctrl2 |= (prio << XGMAC_PSRQ_SHIFT(queue)) &
+						XGMAC_PSRQ(queue);
+
+		writel(ctrl2, ioaddr + XGMAC_RXQ_CTRL2);
+		writel(ctrl3, ioaddr + XGMAC_RXQ_CTRL3);
+	} else {
 		queue -= 4;
 
-	value = readl(ioaddr + reg);
-	value &= ~XGMAC_PSRQ(queue);
-	value |= (prio << XGMAC_PSRQ_SHIFT(queue)) & XGMAC_PSRQ(queue);
+		ctrl3 |= (prio << XGMAC_PSRQ_SHIFT(queue)) &
+						XGMAC_PSRQ(queue);
 
-	writel(value, ioaddr + reg);
+		writel(ctrl3, ioaddr + XGMAC_RXQ_CTRL3);
+		writel(ctrl2, ioaddr + XGMAC_RXQ_CTRL2);
+	}
 }
 
 static void dwxgmac2_tx_queue_prio(struct mac_device_info *hw, u32 prio,
@@ -335,7 +359,8 @@
 }
 
 static void dwxgmac2_set_umac_addr(struct mac_device_info *hw,
-				   unsigned char *addr, unsigned int reg_n)
+				   const unsigned char *addr,
+				   unsigned int reg_n)
 {
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value;
@@ -557,7 +582,7 @@
 }
 
 static void dwxgmac2_update_vlan_hash(struct mac_device_info *hw, u32 hash,
-				      __le16 perfect_match, bool is_double)
+				      u16 perfect_match, bool is_double)
 {
 	void __iomem *ioaddr = hw->pcsr;
 
@@ -788,6 +813,44 @@
 	{ false, "UNKNOWN", "Unknown Error" }, /* 31 */
 };
 
+#define DPP_RX_ERR "Read Rx Descriptor Parity checker Error"
+#define DPP_TX_ERR "Read Tx Descriptor Parity checker Error"
+
+static const struct dwxgmac3_error_desc dwxgmac3_dma_dpp_errors[32] = {
+	{ true, "TDPES0", DPP_TX_ERR },
+	{ true, "TDPES1", DPP_TX_ERR },
+	{ true, "TDPES2", DPP_TX_ERR },
+	{ true, "TDPES3", DPP_TX_ERR },
+	{ true, "TDPES4", DPP_TX_ERR },
+	{ true, "TDPES5", DPP_TX_ERR },
+	{ true, "TDPES6", DPP_TX_ERR },
+	{ true, "TDPES7", DPP_TX_ERR },
+	{ true, "TDPES8", DPP_TX_ERR },
+	{ true, "TDPES9", DPP_TX_ERR },
+	{ true, "TDPES10", DPP_TX_ERR },
+	{ true, "TDPES11", DPP_TX_ERR },
+	{ true, "TDPES12", DPP_TX_ERR },
+	{ true, "TDPES13", DPP_TX_ERR },
+	{ true, "TDPES14", DPP_TX_ERR },
+	{ true, "TDPES15", DPP_TX_ERR },
+	{ true, "RDPES0", DPP_RX_ERR },
+	{ true, "RDPES1", DPP_RX_ERR },
+	{ true, "RDPES2", DPP_RX_ERR },
+	{ true, "RDPES3", DPP_RX_ERR },
+	{ true, "RDPES4", DPP_RX_ERR },
+	{ true, "RDPES5", DPP_RX_ERR },
+	{ true, "RDPES6", DPP_RX_ERR },
+	{ true, "RDPES7", DPP_RX_ERR },
+	{ true, "RDPES8", DPP_RX_ERR },
+	{ true, "RDPES9", DPP_RX_ERR },
+	{ true, "RDPES10", DPP_RX_ERR },
+	{ true, "RDPES11", DPP_RX_ERR },
+	{ true, "RDPES12", DPP_RX_ERR },
+	{ true, "RDPES13", DPP_RX_ERR },
+	{ true, "RDPES14", DPP_RX_ERR },
+	{ true, "RDPES15", DPP_RX_ERR },
+};
+
 static void dwxgmac3_handle_dma_err(struct net_device *ndev,
 				    void __iomem *ioaddr, bool correctable,
 				    struct stmmac_safety_stats *stats)
@@ -799,6 +862,13 @@
 
 	dwxgmac3_log_error(ndev, value, correctable, "DMA",
 			   dwxgmac3_dma_errors, STAT_OFF(dma_errors), stats);
+
+	value = readl(ioaddr + XGMAC_DMA_DPP_INT_STATUS);
+	writel(value, ioaddr + XGMAC_DMA_DPP_INT_STATUS);
+
+	dwxgmac3_log_error(ndev, value, false, "DMA_DPP",
+			   dwxgmac3_dma_dpp_errors,
+			   STAT_OFF(dma_dpp_errors), stats);
 }
 
 static int
@@ -837,6 +907,12 @@
 	value |= XGMAC_TMOUTEN; /* FSM Timeout Feature */
 	writel(value, ioaddr + XGMAC_MAC_FSM_CONTROL);
 
+	/* 5. Enable Data Path Parity Protection */
+	value = readl(ioaddr + XGMAC_MTL_DPP_CONTROL);
+	/* already enabled by default, explicit enable it again */
+	value &= ~XGMAC_DPP_DISABLE;
+	writel(value, ioaddr + XGMAC_MTL_DPP_CONTROL);
+
 	return 0;
 }
 
@@ -870,7 +946,11 @@
 		ret |= !corr;
 	}
 
-	err = dma & (XGMAC_DEUIS | XGMAC_DECIS);
+	/* DMA_DPP_Interrupt_Status is indicated by MCSIS bit in
+	 * DMA_Safety_Interrupt_Status, so we handle DMA Data Path
+	 * Parity Errors here
+	 */
+	err = dma & (XGMAC_DEUIS | XGMAC_DECIS | XGMAC_MCSIS);
 	corr = dma & XGMAC_DECIS;
 	if (err) {
 		dwxgmac3_handle_dma_err(ndev, ioaddr, corr, stats);
@@ -886,6 +966,7 @@
 	{ dwxgmac3_mac_errors },
 	{ dwxgmac3_mtl_errors },
 	{ dwxgmac3_dma_errors },
+	{ dwxgmac3_dma_dpp_errors },
 };
 
 static int dwxgmac3_safety_feat_dump(struct stmmac_safety_stats *stats,
@@ -1134,7 +1215,19 @@
 
 	val |= XGMAC_PPSCMDx(index, XGMAC_PPSCMD_START);
 	val |= XGMAC_TRGTMODSELx(index, XGMAC_PPSCMD_START);
-	val |= XGMAC_PPSEN0;
+
+	/* XGMAC Core has 4 PPS outputs at most.
+	 *
+	 * Prior XGMAC Core 3.20, Fixed mode or Flexible mode are selectable for
+	 * PPS0 only via PPSEN0. PPS{1,2,3} are in Flexible mode by default,
+	 * and can not be switched to Fixed mode, since PPSEN{1,2,3} are
+	 * read-only reserved to 0.
+	 * But we always set PPSEN{1,2,3} do not make things worse ;-)
+	 *
+	 * From XGMAC Core 3.20 and later, PPSEN{0,1,2,3} are writable and must
+	 * be set, or the PPS outputs stay in Fixed PPS mode by default.
+	 */
+	val |= XGMAC_PPSENx(index);
 
 	writel(cfg->start.tv_sec, ioaddr + XGMAC_PPSx_TARGET_TIME_SEC(index));
 
@@ -1428,7 +1521,8 @@
 	return 0;
 }
 
-static void dwxgmac3_fpe_configure(void __iomem *ioaddr, u32 num_txq,
+static void dwxgmac3_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
+				   u32 num_txq,
 				   u32 num_rxq, bool enable)
 {
 	u32 value;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/hwif.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/hwif.h
@@ -330,7 +330,8 @@
 	/* Set power management mode (e.g. magic frame) */
 	void (*pmt)(struct mac_device_info *hw, unsigned long mode);
 	/* Set/Get Unicast MAC addresses */
-	void (*set_umac_addr)(struct mac_device_info *hw, unsigned char *addr,
+	void (*set_umac_addr)(struct mac_device_info *hw,
+			      const unsigned char *addr,
 			      unsigned int reg_n);
 	void (*get_umac_addr)(struct mac_device_info *hw, unsigned char *addr,
 			      unsigned int reg_n);
@@ -369,7 +370,7 @@
 			     struct stmmac_rss *cfg, u32 num_rxq);
 	/* VLAN */
 	void (*update_vlan_hash)(struct mac_device_info *hw, u32 hash,
-				 __le16 perfect_match, bool is_double);
+				 u16 perfect_match, bool is_double);
 	void (*enable_vlan)(struct mac_device_info *hw, u32 type);
 	int (*add_hw_vlan_rx_fltr)(struct net_device *dev,
 				   struct mac_device_info *hw,
@@ -395,9 +396,11 @@
 			     unsigned int ptp_rate);
 	void (*est_irq_status)(void __iomem *ioaddr, struct net_device *dev,
 			       struct stmmac_extra_stats *x, u32 txqcnt);
-	void (*fpe_configure)(void __iomem *ioaddr, u32 num_txq, u32 num_rxq,
+	void (*fpe_configure)(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
+			      u32 num_txq, u32 num_rxq,
 			      bool enable);
 	void (*fpe_send_mpacket)(void __iomem *ioaddr,
+				 struct stmmac_fpe_cfg *cfg,
 				 enum stmmac_mpacket_type type);
 	int (*fpe_irq_status)(void __iomem *ioaddr, struct net_device *dev);
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/mmc_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/mmc_core.c
@@ -177,8 +177,10 @@
 #define MMC_XGMAC_RX_DISCARD_OCT_GB	0x1b4
 #define MMC_XGMAC_RX_ALIGN_ERR_PKT	0x1bc
 
+#define MMC_XGMAC_TX_FPE_INTR_MASK	0x204
 #define MMC_XGMAC_TX_FPE_FRAG		0x208
 #define MMC_XGMAC_TX_HOLD_REQ		0x20c
+#define MMC_XGMAC_RX_FPE_INTR_MASK	0x224
 #define MMC_XGMAC_RX_PKT_ASSEMBLY_ERR	0x228
 #define MMC_XGMAC_RX_PKT_SMD_ERR	0x22c
 #define MMC_XGMAC_RX_PKT_ASSEMBLY_OK	0x230
@@ -352,6 +354,8 @@
 {
 	writel(0x0, mmcaddr + MMC_RX_INTR_MASK);
 	writel(0x0, mmcaddr + MMC_TX_INTR_MASK);
+	writel(MMC_DEFAULT_MASK, mmcaddr + MMC_XGMAC_TX_FPE_INTR_MASK);
+	writel(MMC_DEFAULT_MASK, mmcaddr + MMC_XGMAC_RX_FPE_INTR_MASK);
 	writel(MMC_DEFAULT_MASK, mmcaddr + MMC_XGMAC_RX_IPC_INTR_MASK);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -172,6 +172,19 @@
 	int is_l4;
 };
 
+/* Rx Frame Steering */
+enum stmmac_rfs_type {
+	STMMAC_RFS_T_VLAN,
+	STMMAC_RFS_T_MAX,
+};
+
+struct stmmac_rfs_entry {
+	unsigned long cookie;
+	int in_use;
+	int type;
+	int tc;
+};
+
 struct stmmac_priv {
 	/* Frequently used values are kept adjacent for cache effect */
 	u32 tx_coal_frames[MTL_MAX_TX_QUEUES];
@@ -228,6 +241,7 @@
 	u32 msg_enable;
 	int wolopts;
 	int wol_irq;
+	bool wol_irq_disabled;
 	int clk_csr;
 	struct timer_list eee_ctrl_timer;
 	int lpi_irq;
@@ -252,6 +266,7 @@
 	spinlock_t ptp_lock;
 	/* Protects auxiliary snapshot registers from concurrent access. */
 	struct mutex aux_ts_lock;
+	wait_queue_head_t tstamp_busy_wait;
 
 	void __iomem *mmcaddr;
 	void __iomem *ptpaddr;
@@ -289,6 +304,10 @@
 	struct stmmac_tc_entry *tc_entries;
 	unsigned int flow_entries_max;
 	struct stmmac_flow_entry *flow_entries;
+	unsigned int rfs_entries_max[STMMAC_RFS_T_MAX];
+	unsigned int rfs_entries_cnt[STMMAC_RFS_T_MAX];
+	unsigned int rfs_entries_total;
+	struct stmmac_rfs_entry *rfs_entries;
 
 	/* Pulse Per Second output */
 	struct stmmac_pps_cfg pps[STMMAC_PPS_MAX];
@@ -314,10 +333,11 @@
 int stmmac_xpcs_setup(struct mii_bus *mii);
 void stmmac_set_ethtool_ops(struct net_device *netdev);
 
+int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags);
 void stmmac_ptp_register(struct stmmac_priv *priv);
 void stmmac_ptp_unregister(struct stmmac_priv *priv);
-int stmmac_open(struct net_device *dev);
-int stmmac_release(struct net_device *dev);
+int stmmac_xdp_open(struct net_device *dev);
+void stmmac_xdp_release(struct net_device *dev);
 int stmmac_resume(struct device *dev);
 int stmmac_suspend(struct device *dev);
 int stmmac_dvr_remove(struct device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -21,10 +21,18 @@
 #include "dwxgmac2.h"
 
 #define REG_SPACE_SIZE	0x1060
+#define GMAC4_REG_SPACE_SIZE	0x116C
 #define MAC100_ETHTOOL_NAME	"st_mac100"
 #define GMAC_ETHTOOL_NAME	"st_gmac"
 #define XGMAC_ETHTOOL_NAME	"st_xgmac"
 
+/* Same as DMA_CHAN_BASE_ADDR defined in dwmac4_dma.h
+ *
+ * It is here because dwmac_dma.h and dwmac4_dam.h can not be included at the
+ * same time due to the conflicting macro names.
+ */
+#define GMAC4_DMA_CHAN_BASE_ADDR  0x00001100
+
 #define ETHTOOL_DMA_OFFSET	55
 
 struct stmmac_stats {
@@ -435,6 +443,8 @@
 
 	if (priv->plat->has_xgmac)
 		return XGMAC_REGSIZE * 4;
+	else if (priv->plat->has_gmac4)
+		return GMAC4_REG_SPACE_SIZE;
 	return REG_SPACE_SIZE;
 }
 
@@ -447,8 +457,13 @@
 	stmmac_dump_mac_regs(priv, priv->hw, reg_space);
 	stmmac_dump_dma_regs(priv, priv->ioaddr, reg_space);
 
-	if (!priv->plat->has_xgmac) {
-		/* Copy DMA registers to where ethtool expects them */
+	/* Copy DMA registers to where ethtool expects them */
+	if (priv->plat->has_gmac4) {
+		/* GMAC4 dumps its DMA registers at its DMA_CHAN_BASE_ADDR */
+		memcpy(&reg_space[ETHTOOL_DMA_OFFSET],
+		       &reg_space[GMAC4_DMA_CHAN_BASE_ADDR / 4],
+		       NUM_DWMAC4_DMA_REGS * 4);
+	} else if (!priv->plat->has_xgmac) {
 		memcpy(&reg_space[ETHTOOL_DMA_OFFSET],
 		       &reg_space[DMA_BUS_MODE / 4],
 		       NUM_DWMAC1000_DMA_REGS * 4);
@@ -533,16 +548,16 @@
 		p = (char *)priv + offsetof(struct stmmac_priv,
 					    xstats.txq_stats[q].tx_pkt_n);
 		for (stat = 0; stat < STMMAC_TXQ_STATS; stat++) {
-			*data++ = (*(u64 *)p);
-			p += sizeof(u64 *);
+			*data++ = (*(unsigned long *)p);
+			p += sizeof(unsigned long);
 		}
 	}
 	for (q = 0; q < rx_cnt; q++) {
 		p = (char *)priv + offsetof(struct stmmac_priv,
 					    xstats.rxq_stats[q].rx_pkt_n);
 		for (stat = 0; stat < STMMAC_RXQ_STATS; stat++) {
-			*data++ = (*(u64 *)p);
-			p += sizeof(u64 *);
+			*data++ = (*(unsigned long *)p);
+			p += sizeof(unsigned long);
 		}
 	}
 }
@@ -743,10 +758,16 @@
 	if (wol->wolopts) {
 		pr_info("stmmac: wakeup enable\n");
 		device_set_wakeup_enable(priv->device, 1);
-		enable_irq_wake(priv->wol_irq);
+		/* Avoid unbalanced enable_irq_wake calls */
+		if (priv->wol_irq_disabled)
+			enable_irq_wake(priv->wol_irq);
+		priv->wol_irq_disabled = false;
 	} else {
 		device_set_wakeup_enable(priv->device, 0);
-		disable_irq_wake(priv->wol_irq);
+		/* Avoid unbalanced disable_irq_wake calls */
+		if (!priv->wol_irq_disabled)
+			disable_irq_wake(priv->wol_irq);
+		priv->wol_irq_disabled = true;
 	}
 
 	mutex_lock(&priv->lock);
@@ -785,14 +806,6 @@
 		netdev_warn(priv->dev,
 			    "Setting EEE tx-lpi is not supported\n");
 
-	if (priv->hw->xpcs) {
-		ret = xpcs_config_eee(priv->hw->xpcs,
-				      priv->plat->mult_fact_100ns,
-				      edata->eee_enabled);
-		if (ret)
-			return ret;
-	}
-
 	if (!edata->eee_enabled)
 		stmmac_disable_eee_mode(priv);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c
@@ -47,7 +47,8 @@
 	if (!(value & PTP_TCR_TSCTRLSSR))
 		data = (data * 1000) / 465;
 
-	data &= PTP_SSIR_SSINC_MASK;
+	if (data > PTP_SSIR_SSINC_MAX)
+		data = PTP_SSIR_SSINC_MAX;
 
 	reg_value = data;
 	if (gmac4)
@@ -71,9 +72,9 @@
 	writel(value, ioaddr + PTP_TCR);
 
 	/* wait for present system time initialize to complete */
-	return readl_poll_timeout(ioaddr + PTP_TCR, value,
+	return readl_poll_timeout_atomic(ioaddr + PTP_TCR, value,
 				 !(value & PTP_TCR_TSINIT),
-				 10000, 100000);
+				 10, 100000);
 }
 
 static int config_addend(void __iomem *ioaddr, u32 addend)
@@ -145,15 +146,20 @@
 
 static void get_systime(void __iomem *ioaddr, u64 *systime)
 {
-	u64 ns;
+	u64 ns, sec0, sec1;
 
-	/* Get the TSSS value */
-	ns = readl(ioaddr + PTP_STNSR);
-	/* Get the TSS and convert sec time value to nanosecond */
-	ns += readl(ioaddr + PTP_STSR) * 1000000000ULL;
+	/* Get the TSS value */
+	sec1 = readl_relaxed(ioaddr + PTP_STSR);
+	do {
+		sec0 = sec1;
+		/* Get the TSSS value */
+		ns = readl_relaxed(ioaddr + PTP_STNSR);
+		/* Get the TSS value */
+		sec1 = readl_relaxed(ioaddr + PTP_STSR);
+	} while (sec0 != sec1);
 
 	if (systime)
-		*systime = ns;
+		*systime = ns + (sec1 * 1000000000ULL);
 }
 
 static void get_ptptime(void __iomem *ptpaddr, u64 *ptp_time)
@@ -170,10 +176,16 @@
 {
 	u32 num_snapshot, ts_status, tsync_int;
 	struct ptp_clock_event event;
+	u32 acr_value, channel;
 	unsigned long flags;
 	u64 ptp_time;
 	int i;
 
+	if (priv->plat->int_snapshot_en) {
+		wake_up(&priv->tstamp_busy_wait);
+		return;
+	}
+
 	tsync_int = readl(priv->ioaddr + GMAC_INT_STATUS) & GMAC_INT_TSIE;
 
 	if (!tsync_int)
@@ -190,12 +202,15 @@
 	num_snapshot = (ts_status & GMAC_TIMESTAMP_ATSNS_MASK) >>
 		       GMAC_TIMESTAMP_ATSNS_SHIFT;
 
+	acr_value = readl(priv->ptpaddr + PTP_ACR);
+	channel = ilog2(FIELD_GET(PTP_ACR_MASK, acr_value));
+
 	for (i = 0; i < num_snapshot; i++) {
 		spin_lock_irqsave(&priv->ptp_lock, flags);
 		get_ptptime(priv->ptpaddr, &ptp_time);
 		spin_unlock_irqrestore(&priv->ptp_lock, flags);
 		event.type = PTP_CLOCK_EXTTS;
-		event.index = 0;
+		event.index = channel;
 		event.timestamp = ptp_time;
 		ptp_clock_event(priv->ptp_clock, &event);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -50,6 +50,13 @@
 #include "dwxgmac2.h"
 #include "hwif.h"
 
+/* As long as the interface is active, we keep the timestamping counter enabled
+ * with fine resolution and binary rollover. This avoid non-monotonic behavior
+ * (clock jumps) when changing timestamping settings at runtime.
+ */
+#define STMMAC_HWTS_ACTIVE	(PTP_TCR_TSENA | PTP_TCR_TSCFUPDT | \
+				 PTP_TCR_TSCTRLSSR)
+
 #define	STMMAC_ALIGN(x)		ALIGN(ALIGN(x, SMP_CACHE_BYTES), 16)
 #define	TSO_MAX_BUFF_SIZE	(SZ_16K - 1)
 
@@ -393,7 +400,7 @@
  * Description: this function is to verify and enter in LPI mode in case of
  * EEE.
  */
-static void stmmac_enable_eee_mode(struct stmmac_priv *priv)
+static int stmmac_enable_eee_mode(struct stmmac_priv *priv)
 {
 	u32 tx_cnt = priv->plat->tx_queues_to_use;
 	u32 queue;
@@ -403,13 +410,14 @@
 		struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
 
 		if (tx_q->dirty_tx != tx_q->cur_tx)
-			return; /* still unfinished work */
+			return -EBUSY; /* still unfinished work */
 	}
 
 	/* Check and enter in LPI mode */
 	if (!priv->tx_path_in_lpi_mode)
 		stmmac_set_eee_mode(priv, priv->hw,
 				priv->plat->en_tx_lpi_clockgating);
+	return 0;
 }
 
 /**
@@ -441,8 +449,8 @@
 {
 	struct stmmac_priv *priv = from_timer(priv, t, eee_ctrl_timer);
 
-	stmmac_enable_eee_mode(priv);
-	mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
+	if (stmmac_enable_eee_mode(priv))
+		mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
 }
 
 /**
@@ -511,6 +519,14 @@
 	return true;
 }
 
+static inline u32 stmmac_cdc_adjust(struct stmmac_priv *priv)
+{
+	/* Correct the clk domain crossing(CDC) error */
+	if (priv->plat->has_gmac4 && priv->plat->clk_ptp_rate)
+		return (2 * NSEC_PER_SEC) / priv->plat->clk_ptp_rate;
+	return 0;
+}
+
 /* stmmac_get_tx_hwtstamp - get HW TX timestamps
  * @priv: driver private structure
  * @p : descriptor pointer
@@ -524,7 +540,6 @@
 {
 	struct skb_shared_hwtstamps shhwtstamp;
 	bool found = false;
-	s64 adjust = 0;
 	u64 ns = 0;
 
 	if (!priv->hwts_tx_en)
@@ -543,12 +558,7 @@
 	}
 
 	if (found) {
-		/* Correct the clk domain crossing(CDC) error */
-		if (priv->plat->has_gmac4 && priv->plat->clk_ptp_rate) {
-			adjust += -(2 * (NSEC_PER_SEC /
-					 priv->plat->clk_ptp_rate));
-			ns += adjust;
-		}
+		ns -= stmmac_cdc_adjust(priv);
 
 		memset(&shhwtstamp, 0, sizeof(struct skb_shared_hwtstamps));
 		shhwtstamp.hwtstamp = ns_to_ktime(ns);
@@ -573,7 +583,6 @@
 {
 	struct skb_shared_hwtstamps *shhwtstamp = NULL;
 	struct dma_desc *desc = p;
-	u64 adjust = 0;
 	u64 ns = 0;
 
 	if (!priv->hwts_rx_en)
@@ -586,11 +595,7 @@
 	if (stmmac_get_rx_timestamp_status(priv, p, np, priv->adv_ts)) {
 		stmmac_get_timestamp(priv, desc, priv->adv_ts, &ns);
 
-		/* Correct the clk domain crossing(CDC) error */
-		if (priv->plat->has_gmac4 && priv->plat->clk_ptp_rate) {
-			adjust += 2 * (NSEC_PER_SEC / priv->plat->clk_ptp_rate);
-			ns -= adjust;
-		}
+		ns -= stmmac_cdc_adjust(priv);
 
 		netdev_dbg(priv->dev, "get valid RX hw timestamp %llu\n", ns);
 		shhwtstamp = skb_hwtstamps(skb);
@@ -616,8 +621,6 @@
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
 	struct hwtstamp_config config;
-	struct timespec64 now;
-	u64 temp = 0;
 	u32 ptp_v2 = 0;
 	u32 tstamp_all = 0;
 	u32 ptp_over_ipv4_udp = 0;
@@ -626,11 +629,6 @@
 	u32 snap_type_sel = 0;
 	u32 ts_master_en = 0;
 	u32 ts_event_en = 0;
-	u32 sec_inc = 0;
-	u32 value = 0;
-	bool xmac;
-
-	xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
 
 	if (!(priv->dma_cap.time_stamp || priv->adv_ts)) {
 		netdev_alert(priv->dev, "No support for HW time stamping\n");
@@ -792,42 +790,17 @@
 	priv->hwts_rx_en = ((config.rx_filter == HWTSTAMP_FILTER_NONE) ? 0 : 1);
 	priv->hwts_tx_en = config.tx_type == HWTSTAMP_TX_ON;
 
-	if (!priv->hwts_tx_en && !priv->hwts_rx_en)
-		stmmac_config_hw_tstamping(priv, priv->ptpaddr, 0);
-	else {
-		value = (PTP_TCR_TSENA | PTP_TCR_TSCFUPDT | PTP_TCR_TSCTRLSSR |
-			 tstamp_all | ptp_v2 | ptp_over_ethernet |
-			 ptp_over_ipv6_udp | ptp_over_ipv4_udp | ts_event_en |
-			 ts_master_en | snap_type_sel);
-		stmmac_config_hw_tstamping(priv, priv->ptpaddr, value);
-
-		/* program Sub Second Increment reg */
-		stmmac_config_sub_second_increment(priv,
-				priv->ptpaddr, priv->plat->clk_ptp_rate,
-				xmac, &sec_inc);
-		temp = div_u64(1000000000ULL, sec_inc);
-
-		/* Store sub second increment and flags for later use */
-		priv->sub_second_inc = sec_inc;
-		priv->systime_flags = value;
-
-		/* calculate default added value:
-		 * formula is :
-		 * addend = (2^32)/freq_div_ratio;
-		 * where, freq_div_ratio = 1e9ns/sec_inc
-		 */
-		temp = (u64)(temp << 32);
-		priv->default_addend = div_u64(temp, priv->plat->clk_ptp_rate);
-		stmmac_config_addend(priv, priv->ptpaddr, priv->default_addend);
-
-		/* initialize system time */
-		ktime_get_real_ts64(&now);
-
-		/* lower 32 bits of tv_sec are safe until y2106 */
-		stmmac_init_systime(priv, priv->ptpaddr,
-				(u32)now.tv_sec, now.tv_nsec);
+	priv->systime_flags = STMMAC_HWTS_ACTIVE;
+
+	if (priv->hwts_tx_en || priv->hwts_rx_en) {
+		priv->systime_flags |= tstamp_all | ptp_v2 |
+				       ptp_over_ethernet | ptp_over_ipv6_udp |
+				       ptp_over_ipv4_udp | ts_event_en |
+				       ts_master_en | snap_type_sel;
 	}
 
+	stmmac_config_hw_tstamping(priv, priv->ptpaddr, priv->systime_flags);
+
 	memcpy(&priv->tstamp_config, &config, sizeof(config));
 
 	return copy_to_user(ifr->ifr_data, &config,
@@ -856,6 +829,57 @@
 }
 
 /**
+ * stmmac_init_tstamp_counter - init hardware timestamping counter
+ * @priv: driver private structure
+ * @systime_flags: timestamping flags
+ * Description:
+ * Initialize hardware counter for packet timestamping.
+ * This is valid as long as the interface is open and not suspended.
+ * Will be rerun after resuming from suspend, case in which the timestamping
+ * flags updated by stmmac_hwtstamp_set() also need to be restored.
+ */
+int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags)
+{
+	bool xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
+	struct timespec64 now;
+	u32 sec_inc = 0;
+	u64 temp = 0;
+
+	if (!(priv->dma_cap.time_stamp || priv->dma_cap.atime_stamp))
+		return -EOPNOTSUPP;
+
+	stmmac_config_hw_tstamping(priv, priv->ptpaddr, systime_flags);
+	priv->systime_flags = systime_flags;
+
+	/* program Sub Second Increment reg */
+	stmmac_config_sub_second_increment(priv, priv->ptpaddr,
+					   priv->plat->clk_ptp_rate,
+					   xmac, &sec_inc);
+	temp = div_u64(1000000000ULL, sec_inc);
+
+	/* Store sub second increment for later use */
+	priv->sub_second_inc = sec_inc;
+
+	/* calculate default added value:
+	 * formula is :
+	 * addend = (2^32)/freq_div_ratio;
+	 * where, freq_div_ratio = 1e9ns/sec_inc
+	 */
+	temp = (u64)(temp << 32);
+	priv->default_addend = div_u64(temp, priv->plat->clk_ptp_rate);
+	stmmac_config_addend(priv, priv->ptpaddr, priv->default_addend);
+
+	/* initialize system time */
+	ktime_get_real_ts64(&now);
+
+	/* lower 32 bits of tv_sec are safe until y2106 */
+	stmmac_init_systime(priv, priv->ptpaddr, (u32)now.tv_sec, now.tv_nsec);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(stmmac_init_tstamp_counter);
+
+/**
  * stmmac_init_ptp - init PTP
  * @priv: driver private structure
  * Description: this is to verify if the HW supports the PTPv1 or PTPv2.
@@ -865,9 +889,14 @@
 static int stmmac_init_ptp(struct stmmac_priv *priv)
 {
 	bool xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
+	int ret;
 
-	if (!(priv->dma_cap.time_stamp || priv->dma_cap.atime_stamp))
-		return -EOPNOTSUPP;
+	if (priv->plat->ptp_clk_freq_config)
+		priv->plat->ptp_clk_freq_config(priv);
+
+	ret = stmmac_init_tstamp_counter(priv, STMMAC_HWTS_ACTIVE);
+	if (ret)
+		return ret;
 
 	priv->adv_ts = 0;
 	/* Check if adv_ts can be enabled for dwmac 4.x / xgmac core */
@@ -887,8 +916,6 @@
 	priv->hwts_tx_en = 0;
 	priv->hwts_rx_en = 0;
 
-	stmmac_ptp_register(priv);
-
 	return 0;
 }
 
@@ -1027,7 +1054,8 @@
 	bool *hs_enable = &fpe_cfg->hs_enable;
 
 	if (is_up && *hs_enable) {
-		stmmac_fpe_send_mpacket(priv, priv->ioaddr, MPACKET_VERIFY);
+		stmmac_fpe_send_mpacket(priv, priv->ioaddr, fpe_cfg,
+					MPACKET_VERIFY);
 	} else {
 		*lo_state = FPE_STATE_OFF;
 		*lp_state = FPE_STATE_OFF;
@@ -1056,10 +1084,10 @@
 			       bool tx_pause, bool rx_pause)
 {
 	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
-	u32 ctrl;
+	u32 old_ctrl, ctrl;
 
-	ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
-	ctrl &= ~priv->hw->link.speed_mask;
+	old_ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
+	ctrl = old_ctrl & ~priv->hw->link.speed_mask;
 
 	if (interface == PHY_INTERFACE_MODE_USXGMII) {
 		switch (speed) {
@@ -1131,14 +1159,24 @@
 		ctrl |= priv->hw->link.duplex;
 
 	/* Flow Control operation */
-	if (tx_pause && rx_pause)
-		stmmac_mac_flow_ctrl(priv, duplex);
+	if (rx_pause && tx_pause)
+		priv->flow_ctrl = FLOW_AUTO;
+	else if (rx_pause && !tx_pause)
+		priv->flow_ctrl = FLOW_RX;
+	else if (!rx_pause && tx_pause)
+		priv->flow_ctrl = FLOW_TX;
+	else
+		priv->flow_ctrl = FLOW_OFF;
 
-	writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
+	stmmac_mac_flow_ctrl(priv, duplex);
+
+	if (ctrl != old_ctrl)
+		writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
 
 	stmmac_mac_set(priv, priv->ioaddr, true);
 	if (phy && priv->dma_cap.eee) {
-		priv->eee_active = phy_init_eee(phy, 1) >= 0;
+		priv->eee_active =
+			phy_init_eee(phy, !priv->plat->rx_clk_runs_in_lpi) >= 0;
 		priv->eee_enabled = stmmac_eee_init(priv);
 		priv->tx_lpi_enabled = priv->eee_enabled;
 		stmmac_set_eee_pls(priv, priv->hw, true);
@@ -1206,6 +1244,11 @@
 		int addr = priv->plat->phy_addr;
 		struct phy_device *phydev;
 
+		if (addr < 0) {
+			netdev_err(priv->dev, "no phy found\n");
+			return -ENODEV;
+		}
+
 		phydev = mdiobus_get_phy(priv->mii, addr);
 		if (!phydev) {
 			netdev_err(priv->dev, "no phy at addr %d\n", addr);
@@ -1220,6 +1263,7 @@
 
 		phylink_ethtool_get_wol(priv->phylink, &wol);
 		device_set_wakeup_capable(priv->device, !!wol.supported);
+		device_set_wakeup_enable(priv->device, !!wol.wolopts);
 	}
 
 	return ret;
@@ -1242,6 +1286,8 @@
 	if (!fwnode)
 		fwnode = dev_fwnode(priv->device);
 
+	priv->phylink_config.mac_managed_pm = true;
+
 	phylink = phylink_create(&priv->phylink_config, fwnode,
 				 mode, &stmmac_phylink_mac_ops);
 	if (IS_ERR(phylink))
@@ -2232,6 +2278,23 @@
 	stmmac_stop_tx(priv, priv->ioaddr, chan);
 }
 
+static void stmmac_enable_all_dma_irq(struct stmmac_priv *priv)
+{
+	u32 rx_channels_count = priv->plat->rx_queues_to_use;
+	u32 tx_channels_count = priv->plat->tx_queues_to_use;
+	u32 dma_csr_ch = max(rx_channels_count, tx_channels_count);
+	u32 chan;
+
+	for (chan = 0; chan < dma_csr_ch; chan++) {
+		struct stmmac_channel *ch = &priv->channel[chan];
+		unsigned long flags;
+
+		spin_lock_irqsave(&ch->lock, flags);
+		stmmac_enable_dma_irq(priv, priv->ioaddr, chan, 1, 1);
+		spin_unlock_irqrestore(&ch->lock, flags);
+	}
+}
+
 /**
  * stmmac_start_all_dma - start all RX and TX DMA channels
  * @priv: driver private structure
@@ -2602,8 +2665,8 @@
 
 	if (priv->eee_enabled && !priv->tx_path_in_lpi_mode &&
 	    priv->eee_sw_timer_en) {
-		stmmac_enable_eee_mode(priv);
-		mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
+		if (stmmac_enable_eee_mode(priv))
+			mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
 	}
 
 	/* We still have pending packets, let's call for a new scheduling */
@@ -2867,8 +2930,10 @@
 		stmmac_axi(priv, priv->ioaddr, priv->plat->axi);
 
 	/* DMA CSR Channel configuration */
-	for (chan = 0; chan < dma_csr_ch; chan++)
+	for (chan = 0; chan < dma_csr_ch; chan++) {
 		stmmac_init_chan(priv, priv->ioaddr, priv->plat->dma_cfg, chan);
+		stmmac_disable_dma_irq(priv, priv->ioaddr, chan, 1, 1);
+	}
 
 	/* DMA RX Channel Configuration */
 	for (chan = 0; chan < rx_channels_count; chan++) {
@@ -3203,7 +3268,7 @@
 /**
  * stmmac_hw_setup - setup mac in a usable state.
  *  @dev : pointer to the device structure.
- *  @init_ptp: initialize PTP if set
+ *  @ptp_register: register PTP if set
  *  Description:
  *  this is the main function to setup the HW in a usable state because the
  *  dma engine is reset, the core registers are configured (e.g. AXI,
@@ -3213,7 +3278,7 @@
  *  0 on success and an appropriate (-)ve integer as defined in errno.h
  *  file on failure.
  */
-static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
+static int stmmac_hw_setup(struct net_device *dev, bool ptp_register)
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
 	u32 rx_cnt = priv->plat->rx_queues_to_use;
@@ -3270,18 +3335,22 @@
 
 	stmmac_mmc_setup(priv);
 
-	if (init_ptp) {
+	if (ptp_register) {
 		ret = clk_prepare_enable(priv->plat->clk_ptp_ref);
 		if (ret < 0)
-			netdev_warn(priv->dev, "failed to enable PTP reference clock: %d\n", ret);
-
-		ret = stmmac_init_ptp(priv);
-		if (ret == -EOPNOTSUPP)
-			netdev_warn(priv->dev, "PTP not supported by HW\n");
-		else if (ret)
-			netdev_warn(priv->dev, "PTP init failed\n");
+			netdev_warn(priv->dev,
+				    "failed to enable PTP reference clock: %pe\n",
+				    ERR_PTR(ret));
 	}
 
+	ret = stmmac_init_ptp(priv);
+	if (ret == -EOPNOTSUPP)
+		netdev_warn(priv->dev, "PTP not supported by HW\n");
+	else if (ret)
+		netdev_warn(priv->dev, "PTP init failed\n");
+	else if (ptp_register)
+		stmmac_ptp_register(priv);
+
 	priv->eee_tw_timer = STMMAC_DEFAULT_TWT_LS;
 
 	/* Convert the timer from msec to usec */
@@ -3439,6 +3508,7 @@
 	/* Request the Wake IRQ in case of another line
 	 * is used for WoL
 	 */
+	priv->wol_irq_disabled = true;
 	if (priv->wol_irq > 0 && priv->wol_irq != dev->irq) {
 		int_name = priv->int_name_wol;
 		sprintf(int_name, "%s:%s", dev->name, "wol");
@@ -3580,6 +3650,7 @@
 	/* Request the Wake IRQ in case of another line
 	 * is used for WoL
 	 */
+	priv->wol_irq_disabled = true;
 	if (priv->wol_irq > 0 && priv->wol_irq != dev->irq) {
 		ret = request_irq(priv->wol_irq, stmmac_interrupt,
 				  IRQF_SHARED, dev->name, dev);
@@ -3635,7 +3706,7 @@
  *  0 on success and an appropriate (-)ve integer as defined in errno.h
  *  file on failure.
  */
-int stmmac_open(struct net_device *dev)
+static int stmmac_open(struct net_device *dev)
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
 	int mode = priv->plat->phy_interface;
@@ -3706,6 +3777,15 @@
 		goto init_error;
 	}
 
+	if (priv->plat->serdes_powerup) {
+		ret = priv->plat->serdes_powerup(dev, priv->plat->bsp_priv);
+		if (ret < 0) {
+			netdev_err(priv->dev, "%s: Serdes powerup failed\n",
+				   __func__);
+			goto init_error;
+		}
+	}
+
 	ret = stmmac_hw_setup(dev, true);
 	if (ret < 0) {
 		netdev_err(priv->dev, "%s: Hw setup failed\n", __func__);
@@ -3724,6 +3804,7 @@
 
 	stmmac_enable_all_queues(priv);
 	netif_tx_start_all_queues(priv->dev);
+	stmmac_enable_all_dma_irq(priv);
 
 	return 0;
 
@@ -3747,8 +3828,10 @@
 {
 	set_bit(__FPE_REMOVING, &priv->fpe_task_state);
 
-	if (priv->fpe_wq)
+	if (priv->fpe_wq) {
 		destroy_workqueue(priv->fpe_wq);
+		priv->fpe_wq = NULL;
+	}
 
 	netdev_info(priv->dev, "FPE workqueue stop");
 }
@@ -3759,11 +3842,13 @@
  *  Description:
  *  This is the stop entry point of the driver.
  */
-int stmmac_release(struct net_device *dev)
+static int stmmac_release(struct net_device *dev)
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
 	u32 chan;
 
+	netif_tx_disable(dev);
+
 	if (device_may_wakeup(priv->device))
 		phylink_speed_down(priv->phylink, false);
 	/* Stop and disconnect the PHY */
@@ -3792,6 +3877,10 @@
 	/* Disable the MAC Rx/Tx */
 	stmmac_mac_set(priv, priv->ioaddr, false);
 
+	/* Powerdown Serdes if there is */
+	if (priv->plat->serdes_powerdown)
+		priv->plat->serdes_powerdown(dev, priv->plat->bsp_priv);
+
 	netif_carrier_off(dev);
 
 	stmmac_release_ptp(priv);
@@ -4022,11 +4111,6 @@
 	if (dma_mapping_error(priv->device, des))
 		goto dma_map_err;
 
-	tx_q->tx_skbuff_dma[first_entry].buf = des;
-	tx_q->tx_skbuff_dma[first_entry].len = skb_headlen(skb);
-	tx_q->tx_skbuff_dma[first_entry].map_as_page = false;
-	tx_q->tx_skbuff_dma[first_entry].buf_type = STMMAC_TXBUF_T_SKB;
-
 	if (priv->dma_cap.addr64 <= 32) {
 		first->des0 = cpu_to_le32(des);
 
@@ -4045,6 +4129,23 @@
 
 	stmmac_tso_allocator(priv, des, tmp_pay_len, (nfrags == 0), queue);
 
+	/* In case two or more DMA transmit descriptors are allocated for this
+	 * non-paged SKB data, the DMA buffer address should be saved to
+	 * tx_q->tx_skbuff_dma[].buf corresponding to the last descriptor,
+	 * and leave the other tx_q->tx_skbuff_dma[].buf as NULL to guarantee
+	 * that stmmac_tx_clean() does not unmap the entire DMA buffer too early
+	 * since the tail areas of the DMA buffer can be accessed by DMA engine
+	 * sooner or later.
+	 * By saving the DMA buffer address to tx_q->tx_skbuff_dma[].buf
+	 * corresponding to the last descriptor, stmmac_tx_clean() will unmap
+	 * this DMA buffer right after the DMA engine completely finishes the
+	 * full buffer transmission.
+	 */
+	tx_q->tx_skbuff_dma[tx_q->cur_tx].buf = des;
+	tx_q->tx_skbuff_dma[tx_q->cur_tx].len = skb_headlen(skb);
+	tx_q->tx_skbuff_dma[tx_q->cur_tx].map_as_page = false;
+	tx_q->tx_skbuff_dma[tx_q->cur_tx].buf_type = STMMAC_TXBUF_T_SKB;
+
 	/* Prepare fragments */
 	for (i = 0; i < nfrags; i++) {
 		const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
@@ -4411,13 +4512,10 @@
 
 static void stmmac_rx_vlan(struct net_device *dev, struct sk_buff *skb)
 {
-	struct vlan_ethhdr *veth;
-	__be16 vlan_proto;
+	struct vlan_ethhdr *veth = skb_vlan_eth_hdr(skb);
+	__be16 vlan_proto = veth->h_vlan_proto;
 	u16 vlanid;
 
-	veth = (struct vlan_ethhdr *)skb->data;
-	vlan_proto = veth->h_vlan_proto;
-
 	if ((vlan_proto == htons(ETH_P_8021Q) &&
 	     dev->features & NETIF_F_HW_VLAN_CTAG_RX) ||
 	    (vlan_proto == htons(ETH_P_8021AD) &&
@@ -4960,16 +5058,8 @@
 		buf1_len = stmmac_rx_buf1_len(priv, p, status, len);
 		len += buf1_len;
 
-		/* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
-		 * Type frames (LLC/LLC-SNAP)
-		 *
-		 * llc_snap is never checked in GMAC >= 4, so this ACS
-		 * feature is always disabled and packets need to be
-		 * stripped manually.
-		 */
-		if (likely(!(status & rx_not_ls)) &&
-		    (likely(priv->synopsys_id >= DWMAC_CORE_4_00) ||
-		     unlikely(status != llc_snap))) {
+		/* ACS is disabled; strip manually. */
+		if (likely(!(status & rx_not_ls))) {
 			buf1_len -= ETH_FCS_LEN;
 			len -= ETH_FCS_LEN;
 		}
@@ -5083,10 +5173,10 @@
 			len = 0;
 		}
 
+read_again:
 		if (count >= limit)
 			break;
 
-read_again:
 		buf1_len = 0;
 		buf2_len = 0;
 		entry = next_entry;
@@ -5146,22 +5236,15 @@
 		buf2_len = stmmac_rx_buf2_len(priv, p, status, len);
 		len += buf2_len;
 
-		/* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
-		 * Type frames (LLC/LLC-SNAP)
-		 *
-		 * llc_snap is never checked in GMAC >= 4, so this ACS
-		 * feature is always disabled and packets need to be
-		 * stripped manually.
-		 */
-		if (likely(!(status & rx_not_ls)) &&
-		    (likely(priv->synopsys_id >= DWMAC_CORE_4_00) ||
-		     unlikely(status != llc_snap))) {
-			if (buf2_len)
+		/* ACS is disabled; strip manually. */
+		if (likely(!(status & rx_not_ls))) {
+			if (buf2_len) {
 				buf2_len -= ETH_FCS_LEN;
-			else
+				len -= ETH_FCS_LEN;
+			} else if (buf1_len) {
 				buf1_len -= ETH_FCS_LEN;
-
-			len -= ETH_FCS_LEN;
+				len -= ETH_FCS_LEN;
+			}
 		}
 
 		if (!skb) {
@@ -5499,8 +5582,6 @@
 			       netdev_features_t features)
 {
 	struct stmmac_priv *priv = netdev_priv(netdev);
-	bool sph_en;
-	u32 chan;
 
 	/* Keep the COE Type in case of csum is supporting */
 	if (features & NETIF_F_RXCSUM)
@@ -5512,10 +5593,13 @@
 	 */
 	stmmac_rx_ipc(priv, priv->hw);
 
-	sph_en = (priv->hw->rx_csum > 0) && priv->sph;
+	if (priv->sph_cap) {
+		bool sph_en = (priv->hw->rx_csum > 0) && priv->sph;
+		u32 chan;
 
-	for (chan = 0; chan < priv->plat->rx_queues_to_use; chan++)
-		stmmac_enable_sph(priv, priv->ioaddr, sph_en, chan);
+		for (chan = 0; chan < priv->plat->rx_queues_to_use; chan++)
+			stmmac_enable_sph(priv, priv->ioaddr, sph_en, chan);
+	}
 
 	return 0;
 }
@@ -5538,6 +5622,7 @@
 		/* If user has requested FPE enable, quickly response */
 		if (*hs_enable)
 			stmmac_fpe_send_mpacket(priv, priv->ioaddr,
+						fpe_cfg,
 						MPACKET_RESPONSE);
 	}
 
@@ -5654,11 +5739,6 @@
 	struct net_device *dev = (struct net_device *)dev_id;
 	struct stmmac_priv *priv = netdev_priv(dev);
 
-	if (unlikely(!dev)) {
-		netdev_err(priv->dev, "%s: invalid dev pointer\n", __func__);
-		return IRQ_NONE;
-	}
-
 	/* Check if adapter is up */
 	if (test_bit(STMMAC_DOWN, &priv->state))
 		return IRQ_HANDLED;
@@ -5674,11 +5754,6 @@
 	struct net_device *dev = (struct net_device *)dev_id;
 	struct stmmac_priv *priv = netdev_priv(dev);
 
-	if (unlikely(!dev)) {
-		netdev_err(priv->dev, "%s: invalid dev pointer\n", __func__);
-		return IRQ_NONE;
-	}
-
 	/* Check if adapter is up */
 	if (test_bit(STMMAC_DOWN, &priv->state))
 		return IRQ_HANDLED;
@@ -5698,11 +5773,6 @@
 
 	priv = container_of(tx_q, struct stmmac_priv, tx_queue[chan]);
 
-	if (unlikely(!data)) {
-		netdev_err(priv->dev, "%s: invalid dev pointer\n", __func__);
-		return IRQ_NONE;
-	}
-
 	/* Check if adapter is up */
 	if (test_bit(STMMAC_DOWN, &priv->state))
 		return IRQ_HANDLED;
@@ -5741,11 +5811,6 @@
 
 	priv = container_of(rx_q, struct stmmac_priv, rx_queue[chan]);
 
-	if (unlikely(!data)) {
-		netdev_err(priv->dev, "%s: invalid dev pointer\n", __func__);
-		return IRQ_NONE;
-	}
-
 	/* Check if adapter is up */
 	if (test_bit(STMMAC_DOWN, &priv->state))
 		return IRQ_HANDLED;
@@ -6172,7 +6237,7 @@
 static int stmmac_vlan_update(struct stmmac_priv *priv, bool is_double)
 {
 	u32 crc, hash = 0;
-	__le16 pmatch = 0;
+	u16 pmatch = 0;
 	int count = 0;
 	u16 vid = 0;
 
@@ -6187,7 +6252,7 @@
 		if (count > 2) /* VID = 0 always passes filter */
 			return -EOPNOTSUPP;
 
-		pmatch = cpu_to_le16(vid);
+		pmatch = vid;
 		hash = 0;
 	}
 
@@ -6200,6 +6265,10 @@
 	bool is_double = false;
 	int ret;
 
+	ret = pm_runtime_resume_and_get(priv->device);
+	if (ret < 0)
+		return ret;
+
 	if (be16_to_cpu(proto) == ETH_P_8021AD)
 		is_double = true;
 
@@ -6207,16 +6276,18 @@
 	ret = stmmac_vlan_update(priv, is_double);
 	if (ret) {
 		clear_bit(vid, priv->active_vlans);
-		return ret;
+		goto err_pm_put;
 	}
 
 	if (priv->hw->num_vlan) {
 		ret = stmmac_add_hw_vlan_rx_fltr(priv, ndev, priv->hw, proto, vid);
 		if (ret)
-			return ret;
+			goto err_pm_put;
 	}
+err_pm_put:
+	pm_runtime_put(priv->device);
 
-	return 0;
+	return ret;
 }
 
 static int stmmac_vlan_rx_kill_vid(struct net_device *ndev, __be16 proto, u16 vid)
@@ -6421,6 +6492,146 @@
 	spin_unlock_irqrestore(&ch->lock, flags);
 }
 
+void stmmac_xdp_release(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	u32 chan;
+
+	/* Ensure tx function is not running */
+	netif_tx_disable(dev);
+
+	/* Disable NAPI process */
+	stmmac_disable_all_queues(priv);
+
+	for (chan = 0; chan < priv->plat->tx_queues_to_use; chan++)
+		hrtimer_cancel(&priv->tx_queue[chan].txtimer);
+
+	/* Free the IRQ lines */
+	stmmac_free_irq(dev, REQ_IRQ_ERR_ALL, 0);
+
+	/* Stop TX/RX DMA channels */
+	stmmac_stop_all_dma(priv);
+
+	/* Release and free the Rx/Tx resources */
+	free_dma_desc_resources(priv);
+
+	/* Disable the MAC Rx/Tx */
+	stmmac_mac_set(priv, priv->ioaddr, false);
+
+	/* set trans_start so we don't get spurious
+	 * watchdogs during reset
+	 */
+	netif_trans_update(dev);
+	netif_carrier_off(dev);
+}
+
+int stmmac_xdp_open(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	u32 rx_cnt = priv->plat->rx_queues_to_use;
+	u32 tx_cnt = priv->plat->tx_queues_to_use;
+	u32 dma_csr_ch = max(rx_cnt, tx_cnt);
+	struct stmmac_rx_queue *rx_q;
+	struct stmmac_tx_queue *tx_q;
+	u32 buf_size;
+	bool sph_en;
+	u32 chan;
+	int ret;
+
+	ret = alloc_dma_desc_resources(priv);
+	if (ret < 0) {
+		netdev_err(dev, "%s: DMA descriptors allocation failed\n",
+			   __func__);
+		goto dma_desc_error;
+	}
+
+	ret = init_dma_desc_rings(dev, GFP_KERNEL);
+	if (ret < 0) {
+		netdev_err(dev, "%s: DMA descriptors initialization failed\n",
+			   __func__);
+		goto init_error;
+	}
+
+	/* DMA CSR Channel configuration */
+	for (chan = 0; chan < dma_csr_ch; chan++) {
+		stmmac_init_chan(priv, priv->ioaddr, priv->plat->dma_cfg, chan);
+		stmmac_disable_dma_irq(priv, priv->ioaddr, chan, 1, 1);
+	}
+
+	/* Adjust Split header */
+	sph_en = (priv->hw->rx_csum > 0) && priv->sph;
+
+	/* DMA RX Channel Configuration */
+	for (chan = 0; chan < rx_cnt; chan++) {
+		rx_q = &priv->rx_queue[chan];
+
+		stmmac_init_rx_chan(priv, priv->ioaddr, priv->plat->dma_cfg,
+				    rx_q->dma_rx_phy, chan);
+
+		rx_q->rx_tail_addr = rx_q->dma_rx_phy +
+				     (rx_q->buf_alloc_num *
+				      sizeof(struct dma_desc));
+		stmmac_set_rx_tail_ptr(priv, priv->ioaddr,
+				       rx_q->rx_tail_addr, chan);
+
+		if (rx_q->xsk_pool && rx_q->buf_alloc_num) {
+			buf_size = xsk_pool_get_rx_frame_size(rx_q->xsk_pool);
+			stmmac_set_dma_bfsize(priv, priv->ioaddr,
+					      buf_size,
+					      rx_q->queue_index);
+		} else {
+			stmmac_set_dma_bfsize(priv, priv->ioaddr,
+					      priv->dma_buf_sz,
+					      rx_q->queue_index);
+		}
+
+		stmmac_enable_sph(priv, priv->ioaddr, sph_en, chan);
+	}
+
+	/* DMA TX Channel Configuration */
+	for (chan = 0; chan < tx_cnt; chan++) {
+		tx_q = &priv->tx_queue[chan];
+
+		stmmac_init_tx_chan(priv, priv->ioaddr, priv->plat->dma_cfg,
+				    tx_q->dma_tx_phy, chan);
+
+		tx_q->tx_tail_addr = tx_q->dma_tx_phy;
+		stmmac_set_tx_tail_ptr(priv, priv->ioaddr,
+				       tx_q->tx_tail_addr, chan);
+
+		hrtimer_init(&tx_q->txtimer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+		tx_q->txtimer.function = stmmac_tx_timer;
+	}
+
+	/* Enable the MAC Rx/Tx */
+	stmmac_mac_set(priv, priv->ioaddr, true);
+
+	/* Start Rx & Tx DMA Channels */
+	stmmac_start_all_dma(priv);
+
+	ret = stmmac_request_irq(dev);
+	if (ret)
+		goto irq_error;
+
+	/* Enable NAPI process*/
+	stmmac_enable_all_queues(priv);
+	netif_carrier_on(dev);
+	netif_tx_start_all_queues(dev);
+	stmmac_enable_all_dma_irq(priv);
+
+	return 0;
+
+irq_error:
+	for (chan = 0; chan < priv->plat->tx_queues_to_use; chan++)
+		hrtimer_cancel(&priv->tx_queue[chan].txtimer);
+
+	stmmac_hw_teardown(dev);
+init_error:
+	free_dma_desc_resources(priv);
+dma_desc_error:
+	return ret;
+}
+
 int stmmac_xsk_wakeup(struct net_device *dev, u32 queue, u32 flags)
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
@@ -6670,7 +6881,7 @@
 int stmmac_reinit_queues(struct net_device *dev, u32 rx_cnt, u32 tx_cnt)
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
-	int ret = 0;
+	int ret = 0, i;
 
 	if (netif_running(dev))
 		stmmac_release(dev);
@@ -6679,6 +6890,10 @@
 
 	priv->plat->rx_queues_to_use = rx_cnt;
 	priv->plat->tx_queues_to_use = tx_cnt;
+	if (!netif_is_rxfh_configured(dev))
+		for (i = 0; i < ARRAY_SIZE(priv->rss.table); i++)
+			priv->rss.table[i] = ethtool_rxfh_indir_default(i,
+									rx_cnt);
 
 	stmmac_napi_add(dev);
 
@@ -6725,6 +6940,7 @@
 		if (*lo_state == FPE_STATE_ENTERING_ON &&
 		    *lp_state == FPE_STATE_ENTERING_ON) {
 			stmmac_fpe_configure(priv, priv->ioaddr,
+					     fpe_cfg,
 					     priv->plat->tx_queues_to_use,
 					     priv->plat->rx_queues_to_use,
 					     *enable);
@@ -6743,6 +6959,7 @@
 			netdev_info(priv->dev, SEND_VERIFY_MPAKCET_FMT,
 				    *lo_state, *lp_state);
 			stmmac_fpe_send_mpacket(priv, priv->ioaddr,
+						fpe_cfg,
 						MPACKET_VERIFY);
 		}
 		/* Sleep then retry */
@@ -6757,6 +6974,7 @@
 	if (priv->plat->fpe_cfg->hs_enable != enable) {
 		if (enable) {
 			stmmac_fpe_send_mpacket(priv, priv->ioaddr,
+						priv->plat->fpe_cfg,
 						MPACKET_VERIFY);
 		} else {
 			priv->plat->fpe_cfg->lo_fpe_state = FPE_STATE_OFF;
@@ -6830,7 +7048,8 @@
 	priv->wq = create_singlethread_workqueue("stmmac_wq");
 	if (!priv->wq) {
 		dev_err(priv->device, "failed to create workqueue\n");
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto error_wq_init;
 	}
 
 	INIT_WORK(&priv->service_task, stmmac_service_task);
@@ -6859,6 +7078,9 @@
 		dev_err(priv->device, "unable to bring out of ahb reset: %pe\n",
 			ERR_PTR(ret));
 
+	/* Wait a bit for the reset to take effect */
+	udelay(10);
+
 	/* Init MAC and get the capabilities */
 	ret = stmmac_hw_init(priv);
 	if (ret)
@@ -6889,7 +7111,7 @@
 		dev_info(priv->device, "TSO feature enabled\n");
 	}
 
-	if (priv->dma_cap.sphen) {
+	if (priv->dma_cap.sphen && !priv->plat->sph_disable) {
 		ndev->hw_features |= NETIF_F_GRO;
 		priv->sph_cap = true;
 		priv->sph = priv->sph_cap;
@@ -7003,9 +7225,9 @@
 		/* MDIO bus Registration */
 		ret = stmmac_mdio_register(ndev);
 		if (ret < 0) {
-			dev_err(priv->device,
-				"%s: MDIO bus (id: %d) registration failed",
-				__func__, priv->plat->bus_id);
+			dev_err_probe(priv->device, ret,
+				      "%s: MDIO bus (id: %d) registration failed\n",
+				      __func__, priv->plat->bus_id);
 			goto error_mdio_register;
 		}
 	}
@@ -7032,18 +7254,13 @@
 		goto error_netdev_register;
 	}
 
-	if (priv->plat->serdes_powerup) {
-		ret = priv->plat->serdes_powerup(ndev,
-						 priv->plat->bsp_priv);
-
-		if (ret < 0)
-			goto error_serdes_powerup;
-	}
-
 #ifdef CONFIG_DEBUG_FS
 	stmmac_init_fs(ndev);
 #endif
 
+	if (priv->plat->dump_debug_regs)
+		priv->plat->dump_debug_regs(priv->plat->bsp_priv);
+
 	/* Let pm_runtime_put() disable the clocks.
 	 * If CONFIG_PM is not enabled, the clocks will stay powered.
 	 */
@@ -7051,8 +7268,6 @@
 
 	return ret;
 
-error_serdes_powerup:
-	unregister_netdev(ndev);
 error_netdev_register:
 	phylink_destroy(priv->phylink);
 error_xpcs_setup:
@@ -7064,6 +7279,7 @@
 	stmmac_napi_del(ndev);
 error_hw_init:
 	destroy_workqueue(priv->wq);
+error_wq_init:
 	bitmap_free(priv->af_xdp_zc_qps);
 
 	return ret;
@@ -7083,17 +7299,13 @@
 
 	netdev_info(priv->dev, "%s: removing driver", __func__);
 
+	pm_runtime_get_sync(dev);
+
 	stmmac_stop_all_dma(priv);
 	stmmac_mac_set(priv, priv->ioaddr, false);
 	netif_carrier_off(ndev);
 	unregister_netdev(ndev);
 
-	/* Serdes power down needs to happen after VLAN filter
-	 * is deleted that is triggered by unregister_netdev().
-	 */
-	if (priv->plat->serdes_powerdown)
-		priv->plat->serdes_powerdown(ndev, priv->plat->bsp_priv);
-
 #ifdef CONFIG_DEBUG_FS
 	stmmac_exit_fs(ndev);
 #endif
@@ -7101,8 +7313,6 @@
 	if (priv->plat->stmmac_rst)
 		reset_control_assert(priv->plat->stmmac_rst);
 	reset_control_assert(priv->plat->stmmac_ahb_rst);
-	pm_runtime_put(dev);
-	pm_runtime_disable(dev);
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
@@ -7110,6 +7320,9 @@
 	mutex_destroy(&priv->lock);
 	bitmap_free(priv->af_xdp_zc_qps);
 
+	pm_runtime_disable(dev);
+	pm_runtime_put_noidle(dev);
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(stmmac_dvr_remove);
@@ -7174,6 +7387,7 @@
 	if (priv->dma_cap.fpesel) {
 		/* Disable FPE */
 		stmmac_fpe_configure(priv, priv->ioaddr,
+				     priv->plat->fpe_cfg,
 				     priv->plat->tx_queues_to_use,
 				     priv->plat->rx_queues_to_use, false);
 
@@ -7280,6 +7494,7 @@
 	stmmac_restore_hw_vlan_rx_fltr(priv, ndev, priv->hw);
 
 	stmmac_enable_all_queues(priv);
+	stmmac_enable_all_dma_irq(priv);
 
 	mutex_unlock(&priv->lock);
 	rtnl_unlock();
@@ -7296,7 +7511,7 @@
 	char *opt;
 
 	if (!str || !*str)
-		return -EINVAL;
+		return 1;
 	while ((opt = strsep(&str, ",")) != NULL) {
 		if (!strncmp(opt, "debug:", 6)) {
 			if (kstrtoint(opt + 6, 0, &debug))
@@ -7327,11 +7542,11 @@
 				goto err;
 		}
 	}
-	return 0;
+	return 1;
 
 err:
 	pr_err("%s: ERROR broken module parameter conversion", __func__);
-	return -EINVAL;
+	return 1;
 }
 
 __setup("stmmaceth=", stmmac_cmdline_opt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -489,8 +489,12 @@
 	new_bus->parent = priv->device;
 
 	err = of_mdiobus_register(new_bus, mdio_node);
-	if (err != 0) {
-		dev_err(dev, "Cannot register the MDIO bus\n");
+	if (err == -ENODEV) {
+		err = 0;
+		dev_info(dev, "MDIO bus is disabled\n");
+		goto bus_register_fail;
+	} else if (err) {
+		dev_err_probe(dev, err, "Cannot register the MDIO bus\n");
 		goto bus_register_fail;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
@@ -181,7 +181,7 @@
 		return -ENOMEM;
 
 	/* Enable pci device */
-	ret = pci_enable_device(pdev);
+	ret = pcim_enable_device(pdev);
 	if (ret) {
 		dev_err(&pdev->dev, "%s: ERROR: failed to enable device\n",
 			__func__);
@@ -241,8 +241,6 @@
 		pcim_iounmap_regions(pdev, BIT(i));
 		break;
 	}
-
-	pci_disable_device(pdev);
 }
 
 static int __maybe_unused stmmac_pci_suspend(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -8,6 +8,7 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/module.h>
@@ -108,10 +109,10 @@
 
 	axi->axi_lpi_en = of_property_read_bool(np, "snps,lpi_en");
 	axi->axi_xit_frm = of_property_read_bool(np, "snps,xit_frm");
-	axi->axi_kbbe = of_property_read_bool(np, "snps,axi_kbbe");
-	axi->axi_fb = of_property_read_bool(np, "snps,axi_fb");
-	axi->axi_mb = of_property_read_bool(np, "snps,axi_mb");
-	axi->axi_rb =  of_property_read_bool(np, "snps,axi_rb");
+	axi->axi_kbbe = of_property_read_bool(np, "snps,kbbe");
+	axi->axi_fb = of_property_read_bool(np, "snps,fb");
+	axi->axi_mb = of_property_read_bool(np, "snps,mb");
+	axi->axi_rb =  of_property_read_bool(np, "snps,rb");
 
 	if (of_property_read_u32(np, "snps,wr_osr_lmt", &axi->axi_wr_osr_lmt))
 		axi->axi_wr_osr_lmt = 1;
@@ -293,62 +294,80 @@
 }
 
 /**
- * stmmac_dt_phy - parse device-tree driver parameters to allocate PHY resources
- * @plat: driver data platform structure
- * @np: device tree node
- * @dev: device pointer
- * Description:
- * The mdio bus will be allocated in case of a phy transceiver is on board;
- * it will be NULL if the fixed-link is configured.
- * If there is the "snps,dwmac-mdio" sub-node the mdio will be allocated
- * in any case (for DSA, mdio must be registered even if fixed-link).
- * The table below sums the supported configurations:
- *	-------------------------------
- *	snps,phy-addr	|     Y
- *	-------------------------------
- *	phy-handle	|     Y
- *	-------------------------------
- *	fixed-link	|     N
- *	-------------------------------
- *	snps,dwmac-mdio	|
- *	  even if	|     Y
- *	fixed-link	|
- *	-------------------------------
+ * stmmac_of_get_mdio() - Gets the MDIO bus from the devicetree.
+ * @np: devicetree node
+ *
+ * The MDIO bus will be searched for in the following ways:
+ * 1. The compatible is "snps,dwc-qos-ethernet-4.10" && a "mdio" named
+ *    child node exists
+ * 2. A child node with the "snps,dwmac-mdio" compatible is present
  *
- * It returns 0 in case of success otherwise -ENODEV.
+ * Return: The MDIO node if present otherwise NULL
  */
-static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
-			 struct device_node *np, struct device *dev)
+static struct device_node *stmmac_of_get_mdio(struct device_node *np)
 {
-	bool mdio = !of_phy_is_fixed_link(np);
 	static const struct of_device_id need_mdio_ids[] = {
 		{ .compatible = "snps,dwc-qos-ethernet-4.10" },
 		{},
 	};
+	struct device_node *mdio_node = NULL;
 
 	if (of_match_node(need_mdio_ids, np)) {
-		plat->mdio_node = of_get_child_by_name(np, "mdio");
+		mdio_node = of_get_child_by_name(np, "mdio");
 	} else {
 		/**
 		 * If snps,dwmac-mdio is passed from DT, always register
 		 * the MDIO
 		 */
-		for_each_child_of_node(np, plat->mdio_node) {
-			if (of_device_is_compatible(plat->mdio_node,
+		for_each_child_of_node(np, mdio_node) {
+			if (of_device_is_compatible(mdio_node,
 						    "snps,dwmac-mdio"))
 				break;
 		}
 	}
 
-	if (plat->mdio_node) {
+	return mdio_node;
+}
+
+/**
+ * stmmac_mdio_setup() - Populate platform related MDIO structures.
+ * @plat: driver data platform structure
+ * @np: devicetree node
+ * @dev: device pointer
+ *
+ * This searches for MDIO information from the devicetree.
+ * If an MDIO node is found, it's assigned to plat->mdio_node and
+ * plat->mdio_bus_data is allocated.
+ * If no connection can be determined, just plat->mdio_bus_data is allocated
+ * to indicate a bus should be created and scanned for a phy.
+ * If it's determined there's no MDIO bus needed, both are left NULL.
+ *
+ * This expects that plat->phy_node has already been searched for.
+ *
+ * Return: 0 on success, errno otherwise.
+ */
+static int stmmac_mdio_setup(struct plat_stmmacenet_data *plat,
+			     struct device_node *np, struct device *dev)
+{
+	bool legacy_mdio;
+
+	plat->mdio_node = stmmac_of_get_mdio(np);
+	if (plat->mdio_node)
 		dev_dbg(dev, "Found MDIO subnode\n");
-		mdio = true;
-	}
 
-	if (mdio) {
-		plat->mdio_bus_data =
-			devm_kzalloc(dev, sizeof(struct stmmac_mdio_bus_data),
-				     GFP_KERNEL);
+	/* Legacy devicetrees allowed for no MDIO bus description and expect
+	 * the bus to be scanned for devices. If there's no phy or fixed-link
+	 * described assume this is the case since there must be something
+	 * connected to the MAC.
+	 */
+	legacy_mdio = !of_phy_is_fixed_link(np) && !plat->phy_node;
+	if (legacy_mdio)
+		dev_info(dev, "Deprecated MDIO bus assumption used\n");
+
+	if (plat->mdio_node || legacy_mdio) {
+		plat->mdio_bus_data = devm_kzalloc(dev,
+						   sizeof(*plat->mdio_bus_data),
+						   GFP_KERNEL);
 		if (!plat->mdio_bus_data)
 			return -ENOMEM;
 
@@ -431,8 +450,7 @@
 	plat->phylink_node = np;
 
 	/* Get max speed of operation from device tree */
-	if (of_property_read_u32(np, "max-speed", &plat->max_speed))
-		plat->max_speed = -1;
+	of_property_read_u32(np, "max-speed", &plat->max_speed);
 
 	plat->bus_id = of_alias_get_id(np, "ethernet");
 	if (plat->bus_id < 0)
@@ -453,10 +471,11 @@
 	if (of_property_read_u32(np, "snps,phy-addr", &plat->phy_addr) == 0)
 		dev_warn(&pdev->dev, "snps,phy-addr property is deprecated\n");
 
-	/* To Configure PHY by using all device-tree supported properties */
-	rc = stmmac_dt_phy(plat, np, &pdev->dev);
-	if (rc)
-		return ERR_PTR(rc);
+	rc = stmmac_mdio_setup(plat, np, &pdev->dev);
+	if (rc) {
+		ret = ERR_PTR(rc);
+		goto error_put_phy;
+	}
 
 	of_property_read_u32(np, "tx-fifo-depth", &plat->tx_fifo_size);
 
@@ -542,8 +561,8 @@
 	dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*dma_cfg),
 			       GFP_KERNEL);
 	if (!dma_cfg) {
-		stmmac_remove_config_dt(pdev, plat);
-		return ERR_PTR(-ENOMEM);
+		ret = ERR_PTR(-ENOMEM);
+		goto error_put_mdio;
 	}
 	plat->dma_cfg = dma_cfg;
 
@@ -559,7 +578,7 @@
 	dma_cfg->mixed_burst = of_property_read_bool(np, "snps,mixed-burst");
 
 	plat->force_thresh_dma_mode = of_property_read_bool(np, "snps,force_thresh_dma_mode");
-	if (plat->force_thresh_dma_mode) {
+	if (plat->force_thresh_dma_mode && plat->force_sf_dma_mode) {
 		plat->force_sf_dma_mode = 0;
 		dev_warn(&pdev->dev,
 			 "force_sf_dma_mode is ignored if force_thresh_dma_mode is set.\n");
@@ -571,8 +590,8 @@
 
 	rc = stmmac_mtl_setup(pdev, plat);
 	if (rc) {
-		stmmac_remove_config_dt(pdev, plat);
-		return ERR_PTR(rc);
+		ret = ERR_PTR(rc);
+		goto error_put_mdio;
 	}
 
 	/* clock setup */
@@ -624,10 +643,48 @@
 	clk_disable_unprepare(plat->pclk);
 error_pclk_get:
 	clk_disable_unprepare(plat->stmmac_clk);
+error_put_mdio:
+	of_node_put(plat->mdio_node);
+error_put_phy:
+	of_node_put(plat->phy_node);
 
 	return ret;
 }
 
+static void devm_stmmac_remove_config_dt(void *data)
+{
+	struct plat_stmmacenet_data *plat = data;
+
+	clk_disable_unprepare(plat->stmmac_clk);
+	clk_disable_unprepare(plat->pclk);
+	of_node_put(plat->mdio_node);
+	of_node_put(plat->phy_node);
+}
+
+/**
+ * devm_stmmac_probe_config_dt
+ * @pdev: platform_device structure
+ * @mac: MAC address to use
+ * Description: Devres variant of stmmac_probe_config_dt().
+ */
+struct plat_stmmacenet_data *
+devm_stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac)
+{
+	struct plat_stmmacenet_data *plat;
+	int ret;
+
+	plat = stmmac_probe_config_dt(pdev, mac);
+	if (IS_ERR(plat))
+		return plat;
+
+	ret = devm_add_action_or_reset(&pdev->dev,
+				       devm_stmmac_remove_config_dt, plat);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return plat;
+}
+
 /**
  * stmmac_remove_config_dt - undo the effects of stmmac_probe_config_dt()
  * @pdev: platform_device structure
@@ -650,12 +707,19 @@
 	return ERR_PTR(-EINVAL);
 }
 
+struct plat_stmmacenet_data *
+devm_stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac)
+{
+	return ERR_PTR(-EINVAL);
+}
+
 void stmmac_remove_config_dt(struct platform_device *pdev,
 			     struct plat_stmmacenet_data *plat)
 {
 }
 #endif /* CONFIG_OF */
 EXPORT_SYMBOL_GPL(stmmac_probe_config_dt);
+EXPORT_SYMBOL_GPL(devm_stmmac_probe_config_dt);
 EXPORT_SYMBOL_GPL(stmmac_remove_config_dt);
 
 int stmmac_get_platform_resources(struct platform_device *pdev,
@@ -816,7 +880,13 @@
 		if (ret)
 			return ret;
 
-		clk_prepare_enable(priv->plat->clk_ptp_ref);
+		ret = clk_prepare_enable(priv->plat->clk_ptp_ref);
+		if (ret < 0) {
+			netdev_warn(priv->dev,
+				    "failed to enable PTP reference clock: %pe\n",
+				    ERR_PTR(ret));
+			return ret;
+		}
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
@@ -13,6 +13,8 @@
 
 struct plat_stmmacenet_data *
 stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac);
+struct plat_stmmacenet_data *
+devm_stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac);
 void stmmac_remove_config_dt(struct platform_device *pdev,
 			     struct plat_stmmacenet_data *plat);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
@@ -102,7 +102,7 @@
 		time.tv_nsec = priv->plat->est->btr_reserve[0];
 		time.tv_sec = priv->plat->est->btr_reserve[1];
 		basetime = timespec64_to_ktime(time);
-		cycle_time = priv->plat->est->ctr[1] * NSEC_PER_SEC +
+		cycle_time = (u64)priv->plat->est->ctr[1] * NSEC_PER_SEC +
 			     priv->plat->est->ctr[0];
 		time = stmmac_calc_tas_basetime(basetime,
 						current_time_ns,
@@ -175,11 +175,10 @@
 	struct stmmac_priv *priv =
 	    container_of(ptp, struct stmmac_priv, ptp_clock_ops);
 	void __iomem *ptpaddr = priv->ptpaddr;
-	void __iomem *ioaddr = priv->hw->pcsr;
 	struct stmmac_pps_cfg *cfg;
-	u32 intr_value, acr_value;
 	int ret = -EOPNOTSUPP;
 	unsigned long flags;
+	u32 acr_value;
 
 	switch (rq->type) {
 	case PTP_CLK_REQ_PEROUT:
@@ -213,23 +212,17 @@
 			netdev_dbg(priv->dev, "Auxiliary Snapshot %d enabled.\n",
 				   priv->plat->ext_snapshot_num >>
 				   PTP_ACR_ATSEN_SHIFT);
-			/* Enable Timestamp Interrupt */
-			intr_value = readl(ioaddr + GMAC_INT_EN);
-			intr_value |= GMAC_INT_TSIE;
-			writel(intr_value, ioaddr + GMAC_INT_EN);
-
 		} else {
 			netdev_dbg(priv->dev, "Auxiliary Snapshot %d disabled.\n",
 				   priv->plat->ext_snapshot_num >>
 				   PTP_ACR_ATSEN_SHIFT);
-			/* Disable Timestamp Interrupt */
-			intr_value = readl(ioaddr + GMAC_INT_EN);
-			intr_value &= ~GMAC_INT_TSIE;
-			writel(intr_value, ioaddr + GMAC_INT_EN);
 		}
 		writel(acr_value, ptpaddr + PTP_ACR);
 		mutex_unlock(&priv->aux_ts_lock);
-		ret = 0;
+		/* wait for auxts fifo clear to finish */
+		ret = readl_poll_timeout(ptpaddr + PTP_ACR, acr_value,
+					 !(acr_value & PTP_ACR_ATSFC),
+					 10, 10000);
 		break;
 
 	default:
@@ -297,9 +290,6 @@
 {
 	int i;
 
-	if (priv->plat->ptp_clk_freq_config)
-		priv->plat->ptp_clk_freq_config(priv);
-
 	for (i = 0; i < priv->dma_cap.pps_out_num; i++) {
 		if (i >= STMMAC_PPS_MAX)
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h
@@ -64,7 +64,7 @@
 #define	PTP_TCR_TSENMACADDR	BIT(18)
 
 /* SSIR defines */
-#define	PTP_SSIR_SSINC_MASK		0xff
+#define	PTP_SSIR_SSINC_MAX		0xff
 #define	GMAC4_PTP_SSIR_SSINC_SHIFT	16
 
 /* Auxiliary Control defines */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
@@ -36,7 +36,7 @@
 	int vlan_id_in;
 	int vlan_id_out;
 	unsigned char *src;
-	unsigned char *dst;
+	const unsigned char *dst;
 	u32 ip_src;
 	u32 ip_dst;
 	int tcp;
@@ -249,8 +249,8 @@
 					 struct net_device *orig_ndev)
 {
 	struct stmmac_test_priv *tpriv = pt->af_packet_priv;
+	const unsigned char *dst = tpriv->packet->dst;
 	unsigned char *src = tpriv->packet->src;
-	unsigned char *dst = tpriv->packet->dst;
 	struct stmmachdr *shdr;
 	struct ethhdr *ehdr;
 	struct udphdr *uhdr;
@@ -1084,8 +1084,9 @@
 	unsigned char addr[ETH_ALEN] = {0xde, 0xad, 0xbe, 0xef, 0x00, 0x00};
 	struct tc_cls_u32_offload cls_u32 = { };
 	struct stmmac_packet_attrs attr = { };
-	struct tc_action **actions, *act;
+	struct tc_action **actions;
 	struct tc_u32_sel *sel;
+	struct tcf_gact *gact;
 	struct tcf_exts *exts;
 	int ret, i, nk = 1;
 
@@ -1104,14 +1105,14 @@
 		goto cleanup_sel;
 	}
 
-	actions = kzalloc(nk * sizeof(*actions), GFP_KERNEL);
+	actions = kcalloc(nk, sizeof(*actions), GFP_KERNEL);
 	if (!actions) {
 		ret = -ENOMEM;
 		goto cleanup_exts;
 	}
 
-	act = kzalloc(nk * sizeof(*act), GFP_KERNEL);
-	if (!act) {
+	gact = kcalloc(nk, sizeof(*gact), GFP_KERNEL);
+	if (!gact) {
 		ret = -ENOMEM;
 		goto cleanup_actions;
 	}
@@ -1126,9 +1127,7 @@
 	exts->nr_actions = nk;
 	exts->actions = actions;
 	for (i = 0; i < nk; i++) {
-		struct tcf_gact *gact = to_gact(&act[i]);
-
-		actions[i] = &act[i];
+		actions[i] = (struct tc_action *)&gact[i];
 		gact->tcf_action = TC_ACT_SHOT;
 	}
 
@@ -1152,7 +1151,7 @@
 	stmmac_tc_setup_cls_u32(priv, priv, &cls_u32);
 
 cleanup_act:
-	kfree(act);
+	kfree(gact);
 cleanup_actions:
 	kfree(actions);
 cleanup_exts:
@@ -1655,12 +1654,16 @@
 	}
 
 	ret = stmmac_set_arp_offload(priv, priv->hw, true, ip_addr);
-	if (ret)
+	if (ret) {
+		kfree_skb(skb);
 		goto cleanup;
+	}
 
 	ret = dev_set_promiscuity(priv->dev, 1);
-	if (ret)
+	if (ret) {
+		kfree_skb(skb);
 		goto cleanup;
+	}
 
 	ret = dev_direct_xmit(skb, 0);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
@@ -232,11 +232,33 @@
 	}
 }
 
+static int tc_rfs_init(struct stmmac_priv *priv)
+{
+	int i;
+
+	priv->rfs_entries_max[STMMAC_RFS_T_VLAN] = 8;
+
+	for (i = 0; i < STMMAC_RFS_T_MAX; i++)
+		priv->rfs_entries_total += priv->rfs_entries_max[i];
+
+	priv->rfs_entries = devm_kcalloc(priv->device,
+					 priv->rfs_entries_total,
+					 sizeof(*priv->rfs_entries),
+					 GFP_KERNEL);
+	if (!priv->rfs_entries)
+		return -ENOMEM;
+
+	dev_info(priv->device, "Enabled RFS Flow TC (entries=%d)\n",
+		 priv->rfs_entries_total);
+
+	return 0;
+}
+
 static int tc_init(struct stmmac_priv *priv)
 {
 	struct dma_features *dma_cap = &priv->dma_cap;
 	unsigned int count;
-	int i;
+	int ret, i;
 
 	if (dma_cap->l3l4fnum) {
 		priv->flow_entries_max = dma_cap->l3l4fnum;
@@ -250,10 +272,14 @@
 		for (i = 0; i < priv->flow_entries_max; i++)
 			priv->flow_entries[i].idx = i;
 
-		dev_info(priv->device, "Enabled Flow TC (entries=%d)\n",
+		dev_info(priv->device, "Enabled L3L4 Flow TC (entries=%d)\n",
 			 priv->flow_entries_max);
 	}
 
+	ret = tc_rfs_init(priv);
+	if (ret)
+		return -ENOMEM;
+
 	if (!priv->plat->fpe_cfg) {
 		priv->plat->fpe_cfg = devm_kzalloc(priv->device,
 						   sizeof(*priv->plat->fpe_cfg),
@@ -315,10 +341,11 @@
 			struct tc_cbs_qopt_offload *qopt)
 {
 	u32 tx_queues_count = priv->plat->tx_queues_to_use;
+	s64 port_transmit_rate_kbps;
 	u32 queue = qopt->queue;
-	u32 ptr, speed_div;
 	u32 mode_to_use;
 	u64 value;
+	u32 ptr;
 	int ret;
 
 	/* Queue 0 is not AVB capable */
@@ -327,30 +354,30 @@
 	if (!priv->dma_cap.av)
 		return -EOPNOTSUPP;
 
-	/* Port Transmit Rate and Speed Divider */
-	switch (priv->speed) {
-	case SPEED_10000:
-		ptr = 32;
-		speed_div = 10000000;
-		break;
-	case SPEED_5000:
-		ptr = 32;
-		speed_div = 5000000;
-		break;
-	case SPEED_2500:
-		ptr = 8;
-		speed_div = 2500000;
-		break;
-	case SPEED_1000:
-		ptr = 8;
-		speed_div = 1000000;
-		break;
-	case SPEED_100:
-		ptr = 4;
-		speed_div = 100000;
-		break;
-	default:
-		return -EOPNOTSUPP;
+	port_transmit_rate_kbps = qopt->idleslope - qopt->sendslope;
+
+	if (qopt->enable) {
+		/* Port Transmit Rate and Speed Divider */
+		switch (div_s64(port_transmit_rate_kbps, 1000)) {
+		case SPEED_10000:
+		case SPEED_5000:
+			ptr = 32;
+			break;
+		case SPEED_2500:
+		case SPEED_1000:
+			ptr = 8;
+			break;
+		case SPEED_100:
+			ptr = 4;
+			break;
+		default:
+			netdev_err(priv->dev,
+				   "Invalid portTransmitRate %lld (idleSlope - sendSlope)\n",
+				   port_transmit_rate_kbps);
+			return -EINVAL;
+		}
+	} else {
+		ptr = 0;
 	}
 
 	mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use;
@@ -367,13 +394,14 @@
 			return ret;
 
 		priv->plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB;
+		return 0;
 	}
 
 	/* Final adjustments for HW */
-	value = div_s64(qopt->idleslope * 1024ll * ptr, speed_div);
+	value = div_s64(qopt->idleslope * 1024ll * ptr, port_transmit_rate_kbps);
 	priv->plat->tx_queues_cfg[queue].idle_slope = value & GENMASK(31, 0);
 
-	value = div_s64(-qopt->sendslope * 1024ll * ptr, speed_div);
+	value = div_s64(-qopt->sendslope * 1024ll * ptr, port_transmit_rate_kbps);
 	priv->plat->tx_queues_cfg[queue].send_slope = value & GENMASK(31, 0);
 
 	value = qopt->hicredit * 1024ll * 8;
@@ -607,16 +635,45 @@
 	return ret;
 }
 
+static struct stmmac_rfs_entry *tc_find_rfs(struct stmmac_priv *priv,
+					    struct flow_cls_offload *cls,
+					    bool get_free)
+{
+	int i;
+
+	for (i = 0; i < priv->rfs_entries_total; i++) {
+		struct stmmac_rfs_entry *entry = &priv->rfs_entries[i];
+
+		if (entry->cookie == cls->cookie)
+			return entry;
+		if (get_free && entry->in_use == false)
+			return entry;
+	}
+
+	return NULL;
+}
+
 #define VLAN_PRIO_FULL_MASK (0x07)
 
 static int tc_add_vlan_flow(struct stmmac_priv *priv,
 			    struct flow_cls_offload *cls)
 {
+	struct stmmac_rfs_entry *entry = tc_find_rfs(priv, cls, false);
 	struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
 	struct flow_dissector *dissector = rule->match.dissector;
 	int tc = tc_classid_to_hwtc(priv->dev, cls->classid);
 	struct flow_match_vlan match;
 
+	if (!entry) {
+		entry = tc_find_rfs(priv, cls, true);
+		if (!entry)
+			return -ENOENT;
+	}
+
+	if (priv->rfs_entries_cnt[STMMAC_RFS_T_VLAN] >=
+	    priv->rfs_entries_max[STMMAC_RFS_T_VLAN])
+		return -ENOENT;
+
 	/* Nothing to do here */
 	if (!dissector_uses_key(dissector, FLOW_DISSECTOR_KEY_VLAN))
 		return -EINVAL;
@@ -638,6 +695,12 @@
 
 		prio = BIT(match.key->vlan_priority);
 		stmmac_rx_queue_prio(priv, priv->hw, prio, tc);
+
+		entry->in_use = true;
+		entry->cookie = cls->cookie;
+		entry->tc = tc;
+		entry->type = STMMAC_RFS_T_VLAN;
+		priv->rfs_entries_cnt[STMMAC_RFS_T_VLAN]++;
 	}
 
 	return 0;
@@ -646,20 +709,19 @@
 static int tc_del_vlan_flow(struct stmmac_priv *priv,
 			    struct flow_cls_offload *cls)
 {
-	struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
-	struct flow_dissector *dissector = rule->match.dissector;
-	int tc = tc_classid_to_hwtc(priv->dev, cls->classid);
+	struct stmmac_rfs_entry *entry = tc_find_rfs(priv, cls, false);
 
-	/* Nothing to do here */
-	if (!dissector_uses_key(dissector, FLOW_DISSECTOR_KEY_VLAN))
-		return -EINVAL;
+	if (!entry || !entry->in_use || entry->type != STMMAC_RFS_T_VLAN)
+		return -ENOENT;
 
-	if (tc < 0) {
-		netdev_err(priv->dev, "Invalid traffic class\n");
-		return -EINVAL;
-	}
+	stmmac_rx_queue_prio(priv, priv->hw, 0, entry->tc);
 
-	stmmac_rx_queue_prio(priv, priv->hw, 0, tc);
+	entry->in_use = false;
+	entry->cookie = 0;
+	entry->tc = 0;
+	entry->type = 0;
+
+	priv->rfs_entries_cnt[STMMAC_RFS_T_VLAN]--;
 
 	return 0;
 }
@@ -786,8 +848,6 @@
 		goto disable;
 	if (qopt->num_entries >= dep)
 		return -EINVAL;
-	if (!qopt->base_time)
-		return -ERANGE;
 	if (!qopt->cycle_time)
 		return -ERANGE;
 
@@ -894,6 +954,7 @@
 
 	priv->plat->fpe_cfg->enable = false;
 	stmmac_fpe_configure(priv, priv->ioaddr,
+			     priv->plat->fpe_cfg,
 			     priv->plat->tx_queues_to_use,
 			     priv->plat->rx_queues_to_use,
 			     false);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/stmicro/stmmac/stmmac_xdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/stmicro/stmmac/stmmac_xdp.c
@@ -119,7 +119,7 @@
 
 	need_update = !!priv->xdp_prog != !!prog;
 	if (if_running && need_update)
-		stmmac_release(dev);
+		stmmac_xdp_release(dev);
 
 	old_prog = xchg(&priv->xdp_prog, prog);
 	if (old_prog)
@@ -129,7 +129,7 @@
 	priv->sph = priv->sph_cap && !stmmac_xdp_is_enabled(priv);
 
 	if (if_running && need_update)
-		stmmac_open(dev);
+		stmmac_xdp_open(dev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/cassini.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/cassini.c
@@ -1325,7 +1325,7 @@
 	writel(val, cp->regs + REG_RX_PAGE_SIZE);
 
 	/* enable the header parser if desired */
-	if (CAS_HP_FIRMWARE == cas_prog_null)
+	if (&CAS_HP_FIRMWARE[0] == &cas_prog_null[0])
 		return;
 
 	val = CAS_BASE(HP_CFG_NUM_CPU, CAS_NCPUS > 63 ? 0 : CAS_NCPUS);
@@ -3794,7 +3794,7 @@
 
 	/* program header parser */
 	if ((cp->cas_flags & CAS_FLAG_TARGET_ABORT) ||
-	    (CAS_HP_ALT_FIRMWARE == cas_prog_null)) {
+	    (&CAS_HP_ALT_FIRMWARE[0] == &cas_prog_null[0])) {
 		cas_load_firmware(cp, CAS_HP_FIRMWARE);
 	} else {
 		cas_load_firmware(cp, CAS_HP_ALT_FIRMWARE);
@@ -5123,6 +5123,8 @@
 		cas_shutdown(cp);
 	mutex_unlock(&cp->pm_mutex);
 
+	vfree(cp->fw_data);
+
 	pci_iounmap(pdev, cp->regs);
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/ldmvsw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/ldmvsw.c
@@ -290,6 +290,9 @@
 
 	hp = mdesc_grab();
 
+	if (!hp)
+		return -ENODEV;
+
 	rmac = mdesc_get_property(hp, vdev->mp, remote_macaddr_prop, &len);
 	err = -ENODEV;
 	if (!rmac) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/niu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/niu.c
@@ -4503,7 +4503,7 @@
 
 		err = niu_rbr_fill(np, rp, GFP_KERNEL);
 		if (err)
-			return err;
+			goto out_err;
 	}
 
 	tx_rings = kcalloc(num_tx_rings, sizeof(struct tx_ring_info),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/sunbmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/sunbmac.c
@@ -623,7 +623,7 @@
 	void __iomem *cregs        = bp->creg;
 	void __iomem *bregs        = bp->bregs;
 	__u32 bblk_dvma = (__u32)bp->bblock_dvma;
-	unsigned char *e = &bp->dev->dev_addr[0];
+	const unsigned char *e = &bp->dev->dev_addr[0];
 
 	/* Latch current counters into statistics. */
 	bigmac_get_counters(bp, bregs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/sungem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/sungem.c
@@ -949,17 +949,6 @@
 	return IRQ_HANDLED;
 }
 
-#ifdef CONFIG_NET_POLL_CONTROLLER
-static void gem_poll_controller(struct net_device *dev)
-{
-	struct gem *gp = netdev_priv(dev);
-
-	disable_irq(gp->pdev->irq);
-	gem_interrupt(gp->pdev->irq, dev);
-	enable_irq(gp->pdev->irq);
-}
-#endif
-
 static void gem_tx_timeout(struct net_device *dev, unsigned int txqueue)
 {
 	struct gem *gp = netdev_priv(dev);
@@ -2836,9 +2825,6 @@
 	.ndo_change_mtu		= gem_change_mtu,
 	.ndo_validate_addr	= eth_validate_addr,
 	.ndo_set_mac_address    = gem_set_mac_address,
-#ifdef CONFIG_NET_POLL_CONTROLLER
-	.ndo_poll_controller    = gem_poll_controller,
-#endif
 };
 
 static int gem_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/sunhme.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/sunhme.c
@@ -2039,9 +2039,9 @@
 
 			skb_reserve(copy_skb, 2);
 			skb_put(copy_skb, len);
-			dma_sync_single_for_cpu(hp->dma_dev, dma_addr, len, DMA_FROM_DEVICE);
+			dma_sync_single_for_cpu(hp->dma_dev, dma_addr, len + 2, DMA_FROM_DEVICE);
 			skb_copy_from_linear_data(skb, copy_skb->data, len);
-			dma_sync_single_for_device(hp->dma_dev, dma_addr, len, DMA_FROM_DEVICE);
+			dma_sync_single_for_device(hp->dma_dev, dma_addr, len + 2, DMA_FROM_DEVICE);
 			/* Reuse original ring buffer. */
 			hme_write_rxd(hp, this,
 				      (RXFLAG_OWN|((RX_BUF_ALLOC_SIZE-RX_OFFSET)<<16)),
@@ -3139,7 +3139,7 @@
 	if (err) {
 		printk(KERN_ERR "happymeal(PCI): Cannot register net device, "
 		       "aborting.\n");
-		goto err_out_iounmap;
+		goto err_out_free_coherent;
 	}
 
 	pci_set_drvdata(pdev, hp);
@@ -3172,6 +3172,10 @@
 
 	return 0;
 
+err_out_free_coherent:
+	dma_free_coherent(hp->dma_dev, PAGE_SIZE,
+			  hp->happy_block, hp->hblock_dvma);
+
 err_out_iounmap:
 	iounmap(hp->gregs);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/sunqe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/sunqe.c
@@ -144,7 +144,7 @@
 	void __iomem *cregs = qep->qcregs;
 	void __iomem *mregs = qep->mregs;
 	void __iomem *gregs = qecp->gregs;
-	unsigned char *e = &qep->dev->dev_addr[0];
+	const unsigned char *e = &qep->dev->dev_addr[0];
 	__u32 qblk_dvma = (__u32)qep->qblock_dvma;
 	u32 tmp;
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/sun/sunvnet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/sun/sunvnet.c
@@ -431,6 +431,9 @@
 
 	hp = mdesc_grab();
 
+	if (!hp)
+		return -ENODEV;
+
 	vp = vnet_find_parent(hp, vdev->mp, vdev);
 	if (IS_ERR(vp)) {
 		pr_err("Cannot find port parent vnet\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c
@@ -57,7 +57,7 @@
 	return 0;
 }
 
-static int xlgmac_set_mac_address(struct xlgmac_pdata *pdata, u8 *addr)
+static int xlgmac_set_mac_address(struct xlgmac_pdata *pdata, const u8 *addr)
 {
 	unsigned int mac_addr_hi, mac_addr_lo;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/synopsys/dwc-xlgmac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/synopsys/dwc-xlgmac.h
@@ -410,7 +410,7 @@
 	void (*dev_xmit)(struct xlgmac_channel *channel);
 	int (*dev_read)(struct xlgmac_channel *channel);
 
-	int (*set_mac_address)(struct xlgmac_pdata *pdata, u8 *addr);
+	int (*set_mac_address)(struct xlgmac_pdata *pdata, const u8 *addr);
 	int (*config_rx_mode)(struct xlgmac_pdata *pdata);
 	int (*enable_rx_csum)(struct xlgmac_pdata *pdata);
 	int (*disable_rx_csum)(struct xlgmac_pdata *pdata);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/Kconfig
@@ -33,6 +33,7 @@
 	tristate "TI DaVinci MDIO Support"
 	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
 	select PHYLIB
+	select MDIO_BITBANG
 	help
 	  This driver supports TI's DaVinci MDIO module.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/am65-cpsw-nuss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/am65-cpsw-nuss.c
@@ -53,7 +53,7 @@
 #define AM65_CPSW_MAX_PORTS	8
 
 #define AM65_CPSW_MIN_PACKET_SIZE	VLAN_ETH_ZLEN
-#define AM65_CPSW_MAX_PACKET_SIZE	(VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)
+#define AM65_CPSW_MAX_PACKET_SIZE	2024
 
 #define AM65_CPSW_REG_CTL		0x004
 #define AM65_CPSW_REG_STAT_PORT_EN	0x014
@@ -564,7 +564,15 @@
 		k3_udma_glue_disable_tx_chn(common->tx_chns[i].tx_chn);
 	}
 
+	reinit_completion(&common->tdown_complete);
 	k3_udma_glue_tdown_rx_chn(common->rx_chns.rx_chn, true);
+
+	if (common->pdata.quirks & AM64_CPSW_QUIRK_DMA_RX_TDOWN_IRQ) {
+		i = wait_for_completion_timeout(&common->tdown_complete, msecs_to_jiffies(1000));
+		if (!i)
+			dev_err(common->dev, "rx teardown timeout\n");
+	}
+
 	napi_disable(&common->napi_rx);
 
 	for (i = 0; i < AM65_CPSW_MAX_RX_FLOWS; i++)
@@ -786,6 +794,8 @@
 
 	if (cppi5_desc_is_tdcm(desc_dma)) {
 		dev_dbg(dev, "%s RX tdown flow: %u\n", __func__, flow_idx);
+		if (common->pdata.quirks & AM64_CPSW_QUIRK_DMA_RX_TDOWN_IRQ)
+			complete(&common->tdown_complete);
 		return 0;
 	}
 
@@ -1536,7 +1546,7 @@
 	for (i = 0; i < common->tx_ch_num; i++) {
 		struct am65_cpsw_tx_chn *tx_chn = &common->tx_chns[i];
 
-		if (tx_chn->irq)
+		if (tx_chn->irq > 0)
 			devm_free_irq(dev, tx_chn->irq, tx_chn);
 
 		netif_napi_del(&tx_chn->napi_tx);
@@ -1609,6 +1619,7 @@
 		if (tx_chn->irq <= 0) {
 			dev_err(dev, "Failed to get tx dma irq %d\n",
 				tx_chn->irq);
+			ret = tx_chn->irq ?: -ENXIO;
 			goto err;
 		}
 
@@ -1802,6 +1813,7 @@
 	if (IS_ERR(cpts)) {
 		int ret = PTR_ERR(cpts);
 
+		of_node_put(node);
 		if (ret == -EOPNOTSUPP) {
 			dev_info(dev, "cpts disabled\n");
 			return 0;
@@ -1844,13 +1856,14 @@
 		if (ret < 0) {
 			dev_err(dev, "%pOF error reading port_id %d\n",
 				port_np, ret);
-			return ret;
+			goto of_node_put;
 		}
 
 		if (!port_id || port_id > common->port_num) {
 			dev_err(dev, "%pOF has invalid port_id %u %s\n",
 				port_np, port_id, port_np->name);
-			return -EINVAL;
+			ret = -EINVAL;
+			goto of_node_put;
 		}
 
 		port = am65_common_get_port(common, port_id);
@@ -1866,8 +1879,10 @@
 				(AM65_CPSW_NU_FRAM_PORT_OFFSET * (port_id - 1));
 
 		port->slave.mac_sl = cpsw_sl_get("am65", dev, port->port_base);
-		if (IS_ERR(port->slave.mac_sl))
-			return PTR_ERR(port->slave.mac_sl);
+		if (IS_ERR(port->slave.mac_sl)) {
+			ret = PTR_ERR(port->slave.mac_sl);
+			goto of_node_put;
+		}
 
 		port->disabled = !of_device_is_available(port_np);
 		if (port->disabled) {
@@ -1880,7 +1895,7 @@
 			ret = PTR_ERR(port->slave.ifphy);
 			dev_err(dev, "%pOF error retrieving port phy: %d\n",
 				port_np, ret);
-			return ret;
+			goto of_node_put;
 		}
 
 		port->slave.mac_only =
@@ -1889,10 +1904,12 @@
 		/* get phy/link info */
 		if (of_phy_is_fixed_link(port_np)) {
 			ret = of_phy_register_fixed_link(port_np);
-			if (ret)
-				return dev_err_probe(dev, ret,
+			if (ret) {
+				ret = dev_err_probe(dev, ret,
 						     "failed to register fixed-link phy %pOF\n",
 						     port_np);
+				goto of_node_put;
+			}
 			port->slave.phy_node = of_node_get(port_np);
 		} else {
 			port->slave.phy_node =
@@ -1902,14 +1919,15 @@
 		if (!port->slave.phy_node) {
 			dev_err(dev,
 				"slave[%d] no phy found\n", port_id);
-			return -ENODEV;
+			ret = -ENODEV;
+			goto of_node_put;
 		}
 
 		ret = of_get_phy_mode(port_np, &port->slave.phy_if);
 		if (ret) {
 			dev_err(dev, "%pOF read phy-mode err %d\n",
 				port_np, ret);
-			return ret;
+			goto of_node_put;
 		}
 
 		ret = of_get_mac_address(port_np, port->slave.mac_addr);
@@ -1932,6 +1950,11 @@
 	}
 
 	return 0;
+
+of_node_put:
+	of_node_put(port_np);
+	of_node_put(node);
+	return ret;
 }
 
 static void am65_cpsw_pcpu_stats_free(void *data)
@@ -1970,10 +1993,11 @@
 	ndev_priv->msg_enable = AM65_CPSW_DEBUG;
 	SET_NETDEV_DEV(port->ndev, dev);
 
-	ether_addr_copy(port->ndev->dev_addr, port->slave.mac_addr);
+	eth_hw_addr_set(port->ndev, port->slave.mac_addr);
 
 	port->ndev->min_mtu = AM65_CPSW_MIN_PACKET_SIZE;
-	port->ndev->max_mtu = AM65_CPSW_MAX_PACKET_SIZE;
+	port->ndev->max_mtu = AM65_CPSW_MAX_PACKET_SIZE -
+			      (VLAN_ETH_HLEN + ETH_FCS_LEN);
 	port->ndev->hw_features = NETIF_F_SG |
 				  NETIF_F_RXCSUM |
 				  NETIF_F_HW_CSUM |
@@ -2053,7 +2077,7 @@
 
 	for (i = 0; i < common->port_num; i++) {
 		port = &common->ports[i];
-		if (port->ndev)
+		if (port->ndev && port->ndev->reg_state == NETREG_REGISTERED)
 			unregister_netdev(port->ndev);
 	}
 }
@@ -2466,7 +2490,6 @@
 				port->port_id, ret);
 			goto dl_port_unreg;
 		}
-		devlink_port_type_eth_set(dl_port, port->ndev);
 	}
 
 	return ret;
@@ -2512,7 +2535,10 @@
 
 static int am65_cpsw_nuss_register_ndevs(struct am65_cpsw_common *common)
 {
+	struct am65_cpsw_rx_chn *rx_chan = &common->rx_chns;
+	struct am65_cpsw_tx_chn *tx_chan = common->tx_chns;
 	struct device *dev = common->dev;
+	struct devlink_port *dl_port;
 	struct am65_cpsw_port *port;
 	int ret = 0, i;
 
@@ -2529,6 +2555,26 @@
 		return ret;
 	}
 
+	/* The DMA Channels are not guaranteed to be in a clean state.
+	 * Reset and disable them to ensure that they are back to the
+	 * clean state and ready to be used.
+	 */
+	for (i = 0; i < common->tx_ch_num; i++) {
+		k3_udma_glue_reset_tx_chn(tx_chan[i].tx_chn, &tx_chan[i],
+					  am65_cpsw_nuss_tx_cleanup);
+		k3_udma_glue_disable_tx_chn(tx_chan[i].tx_chn);
+	}
+
+	for (i = 0; i < AM65_CPSW_MAX_RX_FLOWS; i++)
+		k3_udma_glue_reset_rx_chn(rx_chan->rx_chn, i, rx_chan,
+					  am65_cpsw_nuss_rx_cleanup, !!i);
+
+	k3_udma_glue_disable_rx_chn(rx_chan->rx_chn);
+
+	ret = am65_cpsw_nuss_register_devlink(common);
+	if (ret)
+		return ret;
+
 	for (i = 0; i < common->port_num; i++) {
 		port = &common->ports[i];
 
@@ -2541,25 +2587,24 @@
 				i, ret);
 			goto err_cleanup_ndev;
 		}
+
+		dl_port = &port->devlink_port;
+		devlink_port_type_eth_set(dl_port, port->ndev);
 	}
 
 	ret = am65_cpsw_register_notifiers(common);
 	if (ret)
 		goto err_cleanup_ndev;
 
-	ret = am65_cpsw_nuss_register_devlink(common);
-	if (ret)
-		goto clean_unregister_notifiers;
-
 	/* can't auto unregister ndev using devm_add_action() due to
 	 * devres release sequence in DD core for DMA
 	 */
 
 	return 0;
-clean_unregister_notifiers:
-	am65_cpsw_unregister_notifiers(common);
+
 err_cleanup_ndev:
 	am65_cpsw_nuss_cleanup_ndev(common);
+	am65_cpsw_unregister_devlink(common);
 
 	return ret;
 }
@@ -2605,7 +2650,7 @@
 };
 
 static const struct am65_cpsw_pdata am64x_cpswxg_pdata = {
-	.quirks = 0,
+	.quirks = AM64_CPSW_QUIRK_DMA_RX_TDOWN_IRQ,
 	.ale_dev_id = "am64-cpswxg",
 	.fdqring_mode = K3_RINGACC_RING_MODE_RING,
 };
@@ -2668,9 +2713,9 @@
 	if (!node)
 		return -ENOENT;
 	common->port_num = of_get_child_count(node);
+	of_node_put(node);
 	if (common->port_num < 1 || common->port_num > AM65_CPSW_MAX_PORTS)
 		return -ENOENT;
-	of_node_put(node);
 
 	common->rx_flow_id_base = -1;
 	init_completion(&common->tdown_complete);
@@ -2770,7 +2815,8 @@
 	return 0;
 
 err_of_clear:
-	of_platform_device_destroy(common->mdio_dev, NULL);
+	if (common->mdio_dev)
+		of_platform_device_destroy(common->mdio_dev, NULL);
 err_pm_clear:
 	pm_runtime_put_sync(dev);
 	pm_runtime_disable(dev);
@@ -2799,7 +2845,8 @@
 	 */
 	am65_cpsw_nuss_cleanup_ndev(common);
 
-	of_platform_device_destroy(common->mdio_dev, NULL);
+	if (common->mdio_dev)
+		of_platform_device_destroy(common->mdio_dev, NULL);
 
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/am65-cpsw-nuss.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/am65-cpsw-nuss.h
@@ -84,6 +84,7 @@
 };
 
 #define AM65_CPSW_QUIRK_I2027_NO_TX_CSUM BIT(0)
+#define AM64_CPSW_QUIRK_DMA_RX_TDOWN_IRQ BIT(1)
 
 struct am65_cpsw_pdata {
 	u32	quirks;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/am65-cpts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/am65-cpts.c
@@ -649,6 +649,11 @@
 		struct am65_cpts_skb_cb_data *skb_cb =
 					(struct am65_cpts_skb_cb_data *)skb->cb;
 
+		if ((ptp_classify_raw(skb) & PTP_CLASS_V1) &&
+		    ((mtype_seqid & AM65_CPTS_EVENT_1_SEQUENCE_ID_MASK) ==
+		     (skb_cb->skb_mtype_seqid & AM65_CPTS_EVENT_1_SEQUENCE_ID_MASK)))
+			mtype_seqid = skb_cb->skb_mtype_seqid;
+
 		if (mtype_seqid == skb_cb->skb_mtype_seqid) {
 			u64 ns = event->timestamp;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/cpsw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/cpsw.c
@@ -349,7 +349,7 @@
 	struct cpsw_common	*cpsw = ndev_to_cpsw(xmeta->ndev);
 	int			pkt_size = cpsw->rx_packet_max;
 	int			ret = 0, port, ch = xmeta->ch;
-	int			headroom = CPSW_HEADROOM;
+	int			headroom = CPSW_HEADROOM_NA;
 	struct net_device	*ndev = xmeta->ndev;
 	struct cpsw_priv	*priv;
 	struct page_pool	*pool;
@@ -392,7 +392,7 @@
 	}
 
 	if (priv->xdp_prog) {
-		int headroom = CPSW_HEADROOM, size = len;
+		int size = len;
 
 		xdp_init_buff(&xdp, PAGE_SIZE, &priv->xdp_rxq[ch]);
 		if (status & CPDMA_RX_VLAN_ENCAP) {
@@ -442,7 +442,7 @@
 	xmeta->ndev = ndev;
 	xmeta->ch = ch;
 
-	dma = page_pool_get_dma_addr(new_page) + CPSW_HEADROOM;
+	dma = page_pool_get_dma_addr(new_page) + CPSW_HEADROOM_NA;
 	ret = cpdma_chan_submit_mapped(cpsw->rxv[ch].ch, new_page, dma,
 				       pkt_size, 0);
 	if (ret < 0) {
@@ -631,6 +631,8 @@
 		}
 	}
 
+	phy->mac_managed_pm = true;
+
 	slave->phy = phy;
 
 	phy_attached_info(slave->phy);
@@ -856,6 +858,8 @@
 
 err_cleanup:
 	if (!cpsw->usage_count) {
+		napi_disable(&cpsw->napi_rx);
+		napi_disable(&cpsw->napi_tx);
 		cpdma_ctlr_stop(cpsw->dma);
 		cpsw_destroy_xdp_rxqs(cpsw);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/cpsw_ale.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/cpsw_ale.c
@@ -104,23 +104,37 @@
 
 static inline int cpsw_ale_get_field(u32 *ale_entry, u32 start, u32 bits)
 {
-	int idx;
+	int idx, idx2, index;
+	u32 hi_val = 0;
 
 	idx    = start / 32;
+	idx2 = (start + bits - 1) / 32;
+	/* Check if bits to be fetched exceed a word */
+	if (idx != idx2) {
+		index = 2 - idx2; /* flip */
+		hi_val = ale_entry[index] << ((idx2 * 32) - start);
+	}
 	start -= idx * 32;
 	idx    = 2 - idx; /* flip */
-	return (ale_entry[idx] >> start) & BITMASK(bits);
+	return (hi_val + (ale_entry[idx] >> start)) & BITMASK(bits);
 }
 
 static inline void cpsw_ale_set_field(u32 *ale_entry, u32 start, u32 bits,
 				      u32 value)
 {
-	int idx;
+	int idx, idx2, index;
 
 	value &= BITMASK(bits);
-	idx    = start / 32;
+	idx = start / 32;
+	idx2 = (start + bits - 1) / 32;
+	/* Check if bits to be set exceed a word */
+	if (idx != idx2) {
+		index = 2 - idx2; /* flip */
+		ale_entry[index] &= ~(BITMASK(bits + start - (idx2 * 32)));
+		ale_entry[index] |= (value >> ((idx2 * 32) - start));
+	}
 	start -= idx * 32;
-	idx    = 2 - idx; /* flip */
+	idx = 2 - idx; /* flip */
 	ale_entry[idx] &= ~(BITMASK(bits) << start);
 	ale_entry[idx] |=  (value << start);
 }
@@ -1299,10 +1313,8 @@
 	if (!ale)
 		return ERR_PTR(-ENOMEM);
 
-	ale->p0_untag_vid_mask =
-		devm_kmalloc_array(params->dev, BITS_TO_LONGS(VLAN_N_VID),
-				   sizeof(unsigned long),
-				   GFP_KERNEL);
+	ale->p0_untag_vid_mask = devm_bitmap_zalloc(params->dev, VLAN_N_VID,
+						    GFP_KERNEL);
 	if (!ale->p0_untag_vid_mask)
 		return ERR_PTR(-ENOMEM);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/cpsw_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/cpsw_ethtool.c
@@ -364,11 +364,9 @@
 	struct cpsw_common *cpsw = priv->cpsw;
 	int ret;
 
-	ret = pm_runtime_get_sync(cpsw->dev);
-	if (ret < 0) {
+	ret = pm_runtime_resume_and_get(cpsw->dev);
+	if (ret < 0)
 		cpsw_err(priv, drv, "ethtool begin failed %d\n", ret);
-		pm_runtime_put_noidle(cpsw->dev);
-	}
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/cpsw_new.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/cpsw_new.c
@@ -283,7 +283,7 @@
 {
 	struct page *new_page, *page = token;
 	void *pa = page_address(page);
-	int headroom = CPSW_HEADROOM;
+	int headroom = CPSW_HEADROOM_NA;
 	struct cpsw_meta_xdp *xmeta;
 	struct cpsw_common *cpsw;
 	struct net_device *ndev;
@@ -336,7 +336,7 @@
 	}
 
 	if (priv->xdp_prog) {
-		int headroom = CPSW_HEADROOM, size = len;
+		int size = len;
 
 		xdp_init_buff(&xdp, PAGE_SIZE, &priv->xdp_rxq[ch]);
 		if (status & CPDMA_RX_VLAN_ENCAP) {
@@ -386,7 +386,7 @@
 	xmeta->ndev = ndev;
 	xmeta->ch = ch;
 
-	dma = page_pool_get_dma_addr(new_page) + CPSW_HEADROOM;
+	dma = page_pool_get_dma_addr(new_page) + CPSW_HEADROOM_NA;
 	ret = cpdma_chan_submit_mapped(cpsw->rxv[ch].ch, new_page, dma,
 				       pkt_size, 0);
 	if (ret < 0) {
@@ -772,6 +772,9 @@
 			slave->slave_num);
 		return;
 	}
+
+	phy->mac_managed_pm = true;
+
 	slave->phy = phy;
 
 	phy_attached_info(slave->phy);
@@ -1000,7 +1003,7 @@
 			   flags, vid);
 
 	ether_addr_copy(priv->mac_addr, addr->sa_data);
-	ether_addr_copy(ndev->dev_addr, priv->mac_addr);
+	eth_hw_addr_set(ndev, priv->mac_addr);
 	cpsw_set_slave_mac(&cpsw->slaves[slave_no], priv);
 
 	pm_runtime_put(cpsw->dev);
@@ -1246,8 +1249,10 @@
 	data->slave_data = devm_kcalloc(dev, CPSW_SLAVE_PORTS_NUM,
 					sizeof(struct cpsw_slave_data),
 					GFP_KERNEL);
-	if (!data->slave_data)
+	if (!data->slave_data) {
+		of_node_put(tmp_node);
 		return -ENOMEM;
+	}
 
 	/* Populate all the child nodes here...
 	 */
@@ -1341,6 +1346,7 @@
 
 err_node_put:
 	of_node_put(port_np);
+	of_node_put(tmp_node);
 	return ret;
 }
 
@@ -1401,7 +1407,7 @@
 			dev_info(cpsw->dev, "Random MACID = %pM\n",
 				 priv->mac_addr);
 		}
-		ether_addr_copy(ndev->dev_addr, slave_data->mac_addr);
+		eth_hw_addr_set(ndev, slave_data->mac_addr);
 		ether_addr_copy(priv->mac_addr, slave_data->mac_addr);
 
 		cpsw->slaves[i].ndev = ndev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/cpsw_priv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/cpsw_priv.c
@@ -1120,7 +1120,7 @@
 			xmeta->ndev = priv->ndev;
 			xmeta->ch = ch;
 
-			dma = page_pool_get_dma_addr(page) + CPSW_HEADROOM;
+			dma = page_pool_get_dma_addr(page) + CPSW_HEADROOM_NA;
 			ret = cpdma_chan_idle_submit_mapped(cpsw->rxv[ch].ch,
 							    page, dma,
 							    cpsw->rx_packet_max,
@@ -1144,7 +1144,7 @@
 static struct page_pool *cpsw_create_page_pool(struct cpsw_common *cpsw,
 					       int size)
 {
-	struct page_pool_params pp_params;
+	struct page_pool_params pp_params = {};
 	struct page_pool *pool;
 
 	pp_params.order = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/cpts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/cpts.c
@@ -568,7 +568,9 @@
 	for (i = 0; i < CPTS_MAX_EVENTS; i++)
 		list_add(&cpts->pool_data[i].list, &cpts->pool);
 
-	clk_enable(cpts->refclk);
+	err = clk_enable(cpts->refclk);
+	if (err)
+		return err;
 
 	cpts_write32(cpts, CPTS_EN, control);
 	cpts_write32(cpts, TS_PEND_EN, int_enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/davinci_emac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/davinci_emac.c
@@ -113,7 +113,6 @@
 #define EMAC_DEF_RX_NUM_DESC		(128)
 #define EMAC_DEF_MAX_TX_CH		(1) /* Max TX channels configured */
 #define EMAC_DEF_MAX_RX_CH		(1) /* Max RX channels configured */
-#define EMAC_POLL_WEIGHT		(64) /* Default NAPI poll weight */
 
 /* Buffer descriptor parameters */
 #define EMAC_DEF_TX_MAX_SERVICE		(32) /* TX max service BD's */
@@ -420,8 +419,20 @@
 	u32 int_ctrl, num_interrupts = 0;
 	u32 prescale = 0, addnl_dvdr = 1, coal_intvl = 0;
 
-	if (!coal->rx_coalesce_usecs)
-		return -EINVAL;
+	if (!coal->rx_coalesce_usecs) {
+		priv->coal_intvl = 0;
+
+		switch (priv->version) {
+		case EMAC_VERSION_2:
+			emac_ctrl_write(EMAC_DM646X_CMINTCTRL, 0);
+			break;
+		default:
+			emac_ctrl_write(EMAC_CTRL_EWINTTCNT, 0);
+			break;
+		}
+
+		return 0;
+	}
 
 	coal_intvl = coal->rx_coalesce_usecs;
 
@@ -1899,7 +1910,7 @@
 
 	rc = davinci_emac_try_get_mac(pdev, res_ctrl ? 0 : 1, priv->mac_addr);
 	if (!rc)
-		ether_addr_copy(ndev->dev_addr, priv->mac_addr);
+		eth_hw_addr_set(ndev, priv->mac_addr);
 
 	if (!is_valid_ether_addr(priv->mac_addr)) {
 		/* Use random MAC if still none obtained. */
@@ -1911,7 +1922,7 @@
 
 	ndev->netdev_ops = &emac_netdev_ops;
 	ndev->ethtool_ops = &ethtool_ops;
-	netif_napi_add(ndev, &priv->napi, emac_poll, EMAC_POLL_WEIGHT);
+	netif_napi_add(ndev, &priv->napi, emac_poll, NAPI_POLL_WEIGHT);
 
 	pm_runtime_enable(&pdev->dev);
 	rc = pm_runtime_get_sync(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/davinci_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/davinci_mdio.c
@@ -26,6 +26,8 @@
 #include <linux/of_device.h>
 #include <linux/of_mdio.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/mdio-bitbang.h>
+#include <linux/sys_soc.h>
 
 /*
  * This timeout definition is a worst-case ultra defensive measure against
@@ -41,6 +43,7 @@
 
 struct davinci_mdio_of_param {
 	int autosuspend_delay_ms;
+	bool manual_mode;
 };
 
 struct davinci_mdio_regs {
@@ -49,6 +52,15 @@
 #define CONTROL_IDLE		BIT(31)
 #define CONTROL_ENABLE		BIT(30)
 #define CONTROL_MAX_DIV		(0xffff)
+#define CONTROL_CLKDIV		GENMASK(15, 0)
+
+#define MDIO_MAN_MDCLK_O	BIT(2)
+#define MDIO_MAN_OE		BIT(1)
+#define MDIO_MAN_PIN		BIT(0)
+#define MDIO_MANUALMODE		BIT(31)
+
+#define MDIO_PIN               0
+
 
 	u32	alive;
 	u32	link;
@@ -59,7 +71,9 @@
 	u32	userintmasked;
 	u32	userintmaskset;
 	u32	userintmaskclr;
-	u32	__reserved_1[20];
+	u32	manualif;
+	u32	poll;
+	u32	__reserved_1[18];
 
 	struct {
 		u32	access;
@@ -79,6 +93,7 @@
 
 struct davinci_mdio_data {
 	struct mdio_platform_data pdata;
+	struct mdiobb_ctrl bb_ctrl;
 	struct davinci_mdio_regs __iomem *regs;
 	struct clk	*clk;
 	struct device	*dev;
@@ -90,6 +105,7 @@
 	 */
 	bool		skip_scan;
 	u32		clk_div;
+	bool		manual_mode;
 };
 
 static void davinci_mdio_init_clk(struct davinci_mdio_data *data)
@@ -128,9 +144,122 @@
 	writel(data->clk_div | CONTROL_ENABLE, &data->regs->control);
 }
 
-static int davinci_mdio_reset(struct mii_bus *bus)
+static void davinci_mdio_disable(struct davinci_mdio_data *data)
+{
+	u32 reg;
+
+	/* Disable MDIO state machine */
+	reg = readl(&data->regs->control);
+
+	reg &= ~CONTROL_CLKDIV;
+	reg |= data->clk_div;
+
+	reg &= ~CONTROL_ENABLE;
+	writel(reg, &data->regs->control);
+}
+
+static void davinci_mdio_enable_manual_mode(struct davinci_mdio_data *data)
+{
+	u32 reg;
+	/* set manual mode */
+	reg = readl(&data->regs->poll);
+	reg |= MDIO_MANUALMODE;
+	writel(reg, &data->regs->poll);
+}
+
+static void davinci_set_mdc(struct mdiobb_ctrl *ctrl, int level)
+{
+	struct davinci_mdio_data *data;
+	u32 reg;
+
+	data = container_of(ctrl, struct davinci_mdio_data, bb_ctrl);
+	reg = readl(&data->regs->manualif);
+
+	if (level)
+		reg |= MDIO_MAN_MDCLK_O;
+	else
+		reg &= ~MDIO_MAN_MDCLK_O;
+
+	writel(reg, &data->regs->manualif);
+}
+
+static void davinci_set_mdio_dir(struct mdiobb_ctrl *ctrl, int output)
+{
+	struct davinci_mdio_data *data;
+	u32 reg;
+
+	data = container_of(ctrl, struct davinci_mdio_data, bb_ctrl);
+	reg = readl(&data->regs->manualif);
+
+	if (output)
+		reg |= MDIO_MAN_OE;
+	else
+		reg &= ~MDIO_MAN_OE;
+
+	writel(reg, &data->regs->manualif);
+}
+
+static void  davinci_set_mdio_data(struct mdiobb_ctrl *ctrl, int value)
+{
+	struct davinci_mdio_data *data;
+	u32 reg;
+
+	data = container_of(ctrl, struct davinci_mdio_data, bb_ctrl);
+	reg = readl(&data->regs->manualif);
+
+	if (value)
+		reg |= MDIO_MAN_PIN;
+	else
+		reg &= ~MDIO_MAN_PIN;
+
+	writel(reg, &data->regs->manualif);
+}
+
+static int davinci_get_mdio_data(struct mdiobb_ctrl *ctrl)
+{
+	struct davinci_mdio_data *data;
+	unsigned long reg;
+
+	data = container_of(ctrl, struct davinci_mdio_data, bb_ctrl);
+	reg = readl(&data->regs->manualif);
+	return test_bit(MDIO_PIN, &reg);
+}
+
+static int davinci_mdiobb_read(struct mii_bus *bus, int phy, int reg)
+{
+	int ret;
+
+	ret = pm_runtime_resume_and_get(bus->parent);
+	if (ret < 0)
+		return ret;
+
+	ret = mdiobb_read(bus, phy, reg);
+
+	pm_runtime_mark_last_busy(bus->parent);
+	pm_runtime_put_autosuspend(bus->parent);
+
+	return ret;
+}
+
+static int davinci_mdiobb_write(struct mii_bus *bus, int phy, int reg,
+				u16 val)
+{
+	int ret;
+
+	ret = pm_runtime_resume_and_get(bus->parent);
+	if (ret < 0)
+		return ret;
+
+	ret = mdiobb_write(bus, phy, reg, val);
+
+	pm_runtime_mark_last_busy(bus->parent);
+	pm_runtime_put_autosuspend(bus->parent);
+
+	return ret;
+}
+
+static int davinci_mdio_common_reset(struct davinci_mdio_data *data)
 {
-	struct davinci_mdio_data *data = bus->priv;
 	u32 phy_mask, ver;
 	int ret;
 
@@ -140,6 +269,11 @@
 		return ret;
 	}
 
+	if (data->manual_mode) {
+		davinci_mdio_disable(data);
+		davinci_mdio_enable_manual_mode(data);
+	}
+
 	/* wait for scan logic to settle */
 	msleep(PHY_MAX_ADDR * data->access_time);
 
@@ -173,6 +307,23 @@
 	return 0;
 }
 
+static int davinci_mdio_reset(struct mii_bus *bus)
+{
+	struct davinci_mdio_data *data = bus->priv;
+
+	return davinci_mdio_common_reset(data);
+}
+
+static int davinci_mdiobb_reset(struct mii_bus *bus)
+{
+	struct mdiobb_ctrl *ctrl = bus->priv;
+	struct davinci_mdio_data *data;
+
+	data = container_of(ctrl, struct davinci_mdio_data, bb_ctrl);
+
+	return davinci_mdio_common_reset(data);
+}
+
 /* wait until hardware is ready for another user access */
 static inline int wait_for_user_access(struct davinci_mdio_data *data)
 {
@@ -324,6 +475,28 @@
 	return 0;
 }
 
+struct k3_mdio_soc_data {
+	bool manual_mode;
+};
+
+static const struct k3_mdio_soc_data am65_mdio_soc_data = {
+	.manual_mode = true,
+};
+
+static const struct soc_device_attribute k3_mdio_socinfo[] = {
+	{ .family = "AM62X", .revision = "SR1.0", .data = &am65_mdio_soc_data },
+	{ .family = "AM64X", .revision = "SR1.0", .data = &am65_mdio_soc_data },
+	{ .family = "AM64X", .revision = "SR2.0", .data = &am65_mdio_soc_data },
+	{ .family = "AM65X", .revision = "SR1.0", .data = &am65_mdio_soc_data },
+	{ .family = "AM65X", .revision = "SR2.0", .data = &am65_mdio_soc_data },
+	{ .family = "J7200", .revision = "SR1.0", .data = &am65_mdio_soc_data },
+	{ .family = "J7200", .revision = "SR2.0", .data = &am65_mdio_soc_data },
+	{ .family = "J721E", .revision = "SR1.0", .data = &am65_mdio_soc_data },
+	{ .family = "J721E", .revision = "SR2.0", .data = &am65_mdio_soc_data },
+	{ .family = "J721S2", .revision = "SR1.0", .data = &am65_mdio_soc_data},
+	{ /* sentinel */ },
+};
+
 #if IS_ENABLED(CONFIG_OF)
 static const struct davinci_mdio_of_param of_cpsw_mdio_data = {
 	.autosuspend_delay_ms = 100,
@@ -337,6 +510,14 @@
 MODULE_DEVICE_TABLE(of, davinci_mdio_of_mtable);
 #endif
 
+static const struct mdiobb_ops davinci_mdiobb_ops = {
+	.owner = THIS_MODULE,
+	.set_mdc = davinci_set_mdc,
+	.set_mdio_dir = davinci_set_mdio_dir,
+	.set_mdio_data = davinci_set_mdio_data,
+	.get_mdio_data = davinci_get_mdio_data,
+};
+
 static int davinci_mdio_probe(struct platform_device *pdev)
 {
 	struct mdio_platform_data *pdata = dev_get_platdata(&pdev->dev);
@@ -351,7 +532,26 @@
 	if (!data)
 		return -ENOMEM;
 
-	data->bus = devm_mdiobus_alloc(dev);
+	data->manual_mode = false;
+	data->bb_ctrl.ops = &davinci_mdiobb_ops;
+
+	if (IS_ENABLED(CONFIG_OF) && dev->of_node) {
+		const struct soc_device_attribute *soc_match_data;
+
+		soc_match_data = soc_device_match(k3_mdio_socinfo);
+		if (soc_match_data && soc_match_data->data) {
+			const struct k3_mdio_soc_data *socdata =
+						soc_match_data->data;
+
+			data->manual_mode = socdata->manual_mode;
+		}
+	}
+
+	if (data->manual_mode)
+		data->bus = alloc_mdio_bitbang(&data->bb_ctrl);
+	else
+		data->bus = devm_mdiobus_alloc(dev);
+
 	if (!data->bus) {
 		dev_err(dev, "failed to alloc mii bus\n");
 		return -ENOMEM;
@@ -377,11 +577,20 @@
 	}
 
 	data->bus->name		= dev_name(dev);
-	data->bus->read		= davinci_mdio_read;
-	data->bus->write	= davinci_mdio_write;
-	data->bus->reset	= davinci_mdio_reset;
+
+	if (data->manual_mode) {
+		data->bus->read		= davinci_mdiobb_read;
+		data->bus->write	= davinci_mdiobb_write;
+		data->bus->reset	= davinci_mdiobb_reset;
+
+		dev_info(dev, "Configuring MDIO in manual mode\n");
+	} else {
+		data->bus->read		= davinci_mdio_read;
+		data->bus->write	= davinci_mdio_write;
+		data->bus->reset	= davinci_mdio_reset;
+		data->bus->priv		= data;
+	}
 	data->bus->parent	= dev;
-	data->bus->priv		= data;
 
 	data->clk = devm_clk_get(dev, "fck");
 	if (IS_ERR(data->clk)) {
@@ -439,9 +648,13 @@
 {
 	struct davinci_mdio_data *data = platform_get_drvdata(pdev);
 
-	if (data->bus)
+	if (data->bus) {
 		mdiobus_unregister(data->bus);
 
+		if (data->manual_mode)
+			free_mdio_bitbang(data->bus);
+	}
+
 	pm_runtime_dont_use_autosuspend(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 
@@ -458,7 +671,9 @@
 	ctrl = readl(&data->regs->control);
 	ctrl &= ~CONTROL_ENABLE;
 	writel(ctrl, &data->regs->control);
-	wait_for_idle(data);
+
+	if (!data->manual_mode)
+		wait_for_idle(data);
 
 	return 0;
 }
@@ -467,7 +682,12 @@
 {
 	struct davinci_mdio_data *data = dev_get_drvdata(dev);
 
-	davinci_mdio_enable(data);
+	if (data->manual_mode) {
+		davinci_mdio_disable(data);
+		davinci_mdio_enable_manual_mode(data);
+	} else {
+		davinci_mdio_enable(data);
+	}
 	return 0;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/netcp_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/netcp_core.c
@@ -24,7 +24,6 @@
 #include "netcp.h"
 
 #define NETCP_SOP_OFFSET	(NET_IP_ALIGN + NET_SKB_PAD)
-#define NETCP_NAPI_WEIGHT	64
 #define NETCP_TX_TIMEOUT	(5 * HZ)
 #define NETCP_PACKET_SIZE	(ETH_FRAME_LEN + ETH_FCS_LEN)
 #define NETCP_MIN_PACKET_SIZE	ETH_ZLEN
@@ -1262,7 +1261,7 @@
 }
 
 /* Submit the packet */
-static int netcp_ndo_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+static netdev_tx_t netcp_ndo_start_xmit(struct sk_buff *skb, struct net_device *ndev)
 {
 	struct netcp_intf *netcp = netdev_priv(ndev);
 	struct netcp_stats *tx_stats = &netcp->stats;
@@ -2028,14 +2027,14 @@
 
 		emac_arch_get_mac_addr(efuse_mac_addr, efuse, efuse_mac);
 		if (is_valid_ether_addr(efuse_mac_addr))
-			ether_addr_copy(ndev->dev_addr, efuse_mac_addr);
+			eth_hw_addr_set(ndev, efuse_mac_addr);
 		else
 			eth_random_addr(ndev->dev_addr);
 
 		devm_iounmap(dev, efuse);
 		devm_release_mem_region(dev, res.start, size);
 	} else {
-		ret = of_get_mac_address(node_interface, ndev->dev_addr);
+		ret = of_get_ethdev_address(node_interface, ndev);
 		if (ret)
 			eth_random_addr(ndev->dev_addr);
 	}
@@ -2096,8 +2095,8 @@
 	}
 
 	/* NAPI register */
-	netif_napi_add(ndev, &netcp->rx_napi, netcp_rx_poll, NETCP_NAPI_WEIGHT);
-	netif_tx_napi_add(ndev, &netcp->tx_napi, netcp_tx_poll, NETCP_NAPI_WEIGHT);
+	netif_napi_add(ndev, &netcp->rx_napi, netcp_rx_poll, NAPI_POLL_WEIGHT);
+	netif_tx_napi_add(ndev, &netcp->tx_napi, netcp_tx_poll, NAPI_POLL_WEIGHT);
 
 	/* Register the network device */
 	ndev->dev_id		= 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/ti/tlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/ti/tlan.c
@@ -184,7 +184,7 @@
 static void	tlan_read_and_clear_stats(struct net_device *, int);
 static void	tlan_reset_adapter(struct net_device *);
 static void	tlan_finish_reset(struct net_device *);
-static void	tlan_set_mac(struct net_device *, int areg, char *mac);
+static void	tlan_set_mac(struct net_device *, int areg, const char *mac);
 
 static void	__tlan_phy_print(struct net_device *);
 static void	tlan_phy_print(struct net_device *);
@@ -2346,7 +2346,7 @@
  *
  **************************************************************/
 
-static void tlan_set_mac(struct net_device *dev, int areg, char *mac)
+static void tlan_set_mac(struct net_device *dev, int areg, const char *mac)
 {
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/toshiba/ps3_gelic_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/toshiba/ps3_gelic_net.c
@@ -317,15 +317,17 @@
 
 	/* set up the hardware pointers in each descriptor */
 	for (i = 0; i < no; i++, descr++) {
+		dma_addr_t cpu_addr;
+
 		gelic_descr_set_status(descr, GELIC_DESCR_DMA_NOT_IN_USE);
-		descr->bus_addr =
-			dma_map_single(ctodev(card), descr,
-				       GELIC_DESCR_SIZE,
-				       DMA_BIDIRECTIONAL);
 
-		if (!descr->bus_addr)
+		cpu_addr = dma_map_single(ctodev(card), descr,
+					  GELIC_DESCR_SIZE, DMA_BIDIRECTIONAL);
+
+		if (dma_mapping_error(ctodev(card), cpu_addr))
 			goto iommu_error;
 
+		descr->bus_addr = cpu_to_be32(cpu_addr);
 		descr->next = descr + 1;
 		descr->prev = descr - 1;
 	}
@@ -365,26 +367,28 @@
  *
  * allocates a new rx skb, iommu-maps it and attaches it to the descriptor.
  * Activate the descriptor state-wise
+ *
+ * Gelic RX sk_buffs must be aligned to GELIC_NET_RXBUF_ALIGN and the length
+ * must be a multiple of GELIC_NET_RXBUF_ALIGN.
  */
 static int gelic_descr_prepare_rx(struct gelic_card *card,
 				  struct gelic_descr *descr)
 {
+	static const unsigned int rx_skb_size =
+		ALIGN(GELIC_NET_MAX_FRAME, GELIC_NET_RXBUF_ALIGN) +
+		GELIC_NET_RXBUF_ALIGN - 1;
+	dma_addr_t cpu_addr;
 	int offset;
-	unsigned int bufsize;
 
 	if (gelic_descr_get_status(descr) !=  GELIC_DESCR_DMA_NOT_IN_USE)
 		dev_info(ctodev(card), "%s: ERROR status\n", __func__);
-	/* we need to round up the buffer size to a multiple of 128 */
-	bufsize = ALIGN(GELIC_NET_MAX_MTU, GELIC_NET_RXBUF_ALIGN);
 
-	/* and we need to have it 128 byte aligned, therefore we allocate a
-	 * bit more */
-	descr->skb = dev_alloc_skb(bufsize + GELIC_NET_RXBUF_ALIGN - 1);
+	descr->skb = netdev_alloc_skb(*card->netdev, rx_skb_size);
 	if (!descr->skb) {
 		descr->buf_addr = 0; /* tell DMAC don't touch memory */
 		return -ENOMEM;
 	}
-	descr->buf_size = cpu_to_be32(bufsize);
+	descr->buf_size = cpu_to_be32(rx_skb_size);
 	descr->dmac_cmd_status = 0;
 	descr->result_size = 0;
 	descr->valid_size = 0;
@@ -395,11 +399,10 @@
 	if (offset)
 		skb_reserve(descr->skb, GELIC_NET_RXBUF_ALIGN - offset);
 	/* io-mmu-map the skb */
-	descr->buf_addr = cpu_to_be32(dma_map_single(ctodev(card),
-						     descr->skb->data,
-						     GELIC_NET_MAX_MTU,
-						     DMA_FROM_DEVICE));
-	if (!descr->buf_addr) {
+	cpu_addr = dma_map_single(ctodev(card), descr->skb->data,
+				  GELIC_NET_MAX_FRAME, DMA_FROM_DEVICE);
+	descr->buf_addr = cpu_to_be32(cpu_addr);
+	if (dma_mapping_error(ctodev(card), cpu_addr)) {
 		dev_kfree_skb_any(descr->skb);
 		descr->skb = NULL;
 		dev_info(ctodev(card),
@@ -779,7 +782,7 @@
 
 	buf = dma_map_single(ctodev(card), skb->data, skb->len, DMA_TO_DEVICE);
 
-	if (!buf) {
+	if (dma_mapping_error(ctodev(card), buf)) {
 		dev_err(ctodev(card),
 			"dma map 2 failed (%p, %i). Dropping packet\n",
 			skb->data, skb->len);
@@ -915,7 +918,7 @@
 	data_error = be32_to_cpu(descr->data_error);
 	/* unmap skb buffer */
 	dma_unmap_single(ctodev(card), be32_to_cpu(descr->buf_addr),
-			 GELIC_NET_MAX_MTU,
+			 GELIC_NET_MAX_FRAME,
 			 DMA_FROM_DEVICE);
 
 	skb_put(skb, be32_to_cpu(descr->valid_size)?
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/toshiba/ps3_gelic_net.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/toshiba/ps3_gelic_net.h
@@ -19,8 +19,9 @@
 #define GELIC_NET_RX_DESCRIPTORS        128 /* num of descriptors */
 #define GELIC_NET_TX_DESCRIPTORS        128 /* num of descriptors */
 
-#define GELIC_NET_MAX_MTU               VLAN_ETH_FRAME_LEN
-#define GELIC_NET_MIN_MTU               VLAN_ETH_ZLEN
+#define GELIC_NET_MAX_FRAME             2312
+#define GELIC_NET_MAX_MTU               2294
+#define GELIC_NET_MIN_MTU               64
 #define GELIC_NET_RXBUF_ALIGN           128
 #define GELIC_CARD_RX_CSUM_DEFAULT      1 /* hw chksum */
 #define GELIC_NET_WATCHDOG_TIMEOUT      5*HZ
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/toshiba/ps3_gelic_wireless.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/toshiba/ps3_gelic_wireless.c
@@ -1217,7 +1217,7 @@
 		key_index = wl->current_key;
 
 	if (!enc->length && (ext->ext_flags & IW_ENCODE_EXT_SET_TX_KEY)) {
-		/* reques to change default key index */
+		/* request to change default key index */
 		pr_debug("%s: request to change default key to %d\n",
 			 __func__, key_index);
 		wl->current_key = key_index;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/toshiba/spider_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/toshiba/spider_net.c
@@ -2332,7 +2332,7 @@
 	struct spider_net_card *card;
 
 	netdev = alloc_etherdev(struct_size(card, darray,
-					    tx_descriptors + rx_descriptors));
+					    size_add(tx_descriptors, rx_descriptors)));
 	if (!netdev)
 		return NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/toshiba/tc35815.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/toshiba/tc35815.c
@@ -1859,7 +1859,8 @@
 	return &dev->stats;
 }
 
-static void tc35815_set_cam_entry(struct net_device *dev, int index, unsigned char *addr)
+static void tc35815_set_cam_entry(struct net_device *dev, int index,
+				  const unsigned char *addr)
 {
 	struct tc35815_local *lp = netdev_priv(dev);
 	struct tc35815_regs __iomem *tr =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/tundra/tsi108_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/tundra/tsi108_eth.c
@@ -1302,12 +1302,15 @@
 
 	data->rxring = dma_alloc_coherent(&data->pdev->dev, rxring_size,
 					  &data->rxdma, GFP_KERNEL);
-	if (!data->rxring)
+	if (!data->rxring) {
+		free_irq(data->irq_num, dev);
 		return -ENOMEM;
+	}
 
 	data->txring = dma_alloc_coherent(&data->pdev->dev, txring_size,
 					  &data->txdma, GFP_KERNEL);
 	if (!data->txring) {
+		free_irq(data->irq_num, dev);
 		dma_free_coherent(&data->pdev->dev, rxring_size, data->rxring,
 				    data->rxdma);
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/Kconfig
@@ -1,6 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
 #
-# Xilink device configuration
+# Xilinx device configuration
 #
 
 config NET_VENDOR_XILINX
@@ -26,11 +26,24 @@
 config XILINX_AXI_EMAC
 	tristate "Xilinx 10/100/1000 AXI Ethernet support"
 	depends on HAS_IOMEM
-	select PHYLINK
+	select PHYLIB
 	help
 	  This driver supports the 10/100/1000 Ethernet from Xilinx for the
 	  AXI bus interface used in Xilinx Virtex FPGAs and Soc's.
 
+config XILINX_AXI_EMAC_HWTSTAMP
+	bool "Generate hardware packet timestamps"
+	depends on XILINX_AXI_EMAC
+	select PTP_1588_CLOCK
+	help
+	  Generate hardware packet timestamps. This is to facilitate IEEE 1588.
+
+config AXIENET_HAS_MCDMA
+	bool "AXI Ethernet is configured with MCDMA"
+	depends on XILINX_AXI_EMAC
+	help
+	  When hardware is generated with AXI Ethernet with MCDMA select this option.
+
 config XILINX_LL_TEMAC
 	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
 	depends on HAS_IOMEM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/Makefile
@@ -1,10 +1,11 @@
 # SPDX-License-Identifier: GPL-2.0
 #
-# Makefile for the Xilink network device drivers.
+# Makefile for the Xilinx network device drivers.
 #
 
 ll_temac-objs := ll_temac_main.o ll_temac_mdio.o
 obj-$(CONFIG_XILINX_LL_TEMAC) += ll_temac.o
 obj-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
-xilinx_emac-objs := xilinx_axienet_main.o xilinx_axienet_mdio.o
+xilinx_emac-objs := xilinx_axienet_main.o xilinx_axienet_mdio.o xilinx_axienet_dma.o
 obj-$(CONFIG_XILINX_AXI_EMAC) += xilinx_emac.o
+obj-$(CONFIG_AXIENET_HAS_MCDMA) += xilinx_axienet_mcdma.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/ll_temac_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/ll_temac_main.c
@@ -1427,11 +1427,13 @@
 		lp->indirect_lock = devm_kmalloc(&pdev->dev,
 						 sizeof(*lp->indirect_lock),
 						 GFP_KERNEL);
+		if (!lp->indirect_lock)
+			return -ENOMEM;
 		spin_lock_init(lp->indirect_lock);
 	}
 
 	/* map device registers */
-	lp->regs = devm_platform_ioremap_resource_byname(pdev, 0);
+	lp->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(lp->regs)) {
 		dev_err(&pdev->dev, "could not map TEMAC registers\n");
 		return -ENOMEM;
@@ -1554,15 +1556,15 @@
 	}
 
 	/* Error handle returned DMA RX and TX interrupts */
-	if (lp->rx_irq < 0) {
-		if (lp->rx_irq != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "could not get DMA RX irq\n");
-		return lp->rx_irq;
-	}
-	if (lp->tx_irq < 0) {
-		if (lp->tx_irq != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "could not get DMA TX irq\n");
-		return lp->tx_irq;
+	if (lp->rx_irq <= 0) {
+		rc = lp->rx_irq ?: -EINVAL;
+		return dev_err_probe(&pdev->dev, rc,
+				     "could not get DMA RX irq\n");
+	}
+	if (lp->tx_irq <= 0) {
+		rc = lp->tx_irq ?: -EINVAL;
+		return dev_err_probe(&pdev->dev, rc,
+				     "could not get DMA TX irq\n");
 	}
 
 	if (temac_np) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/xilinx_axienet.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/xilinx_axienet.h
@@ -13,7 +13,10 @@
 #include <linux/spinlock.h>
 #include <linux/interrupt.h>
 #include <linux/if_vlan.h>
-#include <linux/phylink.h>
+#include <linux/net_tstamp.h>
+#include <linux/phy.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
 
 /* Packet size info */
 #define XAE_HDR_SIZE			14 /* Size of Ethernet header */
@@ -25,29 +28,39 @@
 #define XAE_MAX_VLAN_FRAME_SIZE  (XAE_MTU + VLAN_ETH_HLEN + XAE_TRL_SIZE)
 #define XAE_MAX_JUMBO_FRAME_SIZE (XAE_JUMBO_MTU + XAE_HDR_SIZE + XAE_TRL_SIZE)
 
+/* DMA address width min and max range */
+#define XAE_DMA_MASK_MIN	32
+#define XAE_DMA_MASK_MAX	64
+
+/* In AXI DMA Tx and Rx queue count is same */
+#define for_each_tx_dma_queue(lp, var) \
+	for ((var) = 0; (var) < (lp)->num_tx_queues; (var)++)
+
+#define for_each_rx_dma_queue(lp, var) \
+	for ((var) = 0; (var) < (lp)->num_rx_queues; (var)++)
 /* Configuration options */
 
 /* Accept all incoming packets. Default: disabled (cleared) */
-#define XAE_OPTION_PROMISC			(1 << 0)
+#define XAE_OPTION_PROMISC			BIT(0)
 
 /* Jumbo frame support for Tx & Rx. Default: disabled (cleared) */
-#define XAE_OPTION_JUMBO			(1 << 1)
+#define XAE_OPTION_JUMBO			BIT(1)
 
 /* VLAN Rx & Tx frame support. Default: disabled (cleared) */
-#define XAE_OPTION_VLAN				(1 << 2)
+#define XAE_OPTION_VLAN				BIT(2)
 
 /* Enable recognition of flow control frames on Rx. Default: enabled (set) */
-#define XAE_OPTION_FLOW_CONTROL			(1 << 4)
+#define XAE_OPTION_FLOW_CONTROL			BIT(4)
 
 /* Strip FCS and PAD from incoming frames. Note: PAD from VLAN frames is not
  * stripped. Default: disabled (set)
  */
-#define XAE_OPTION_FCS_STRIP			(1 << 5)
+#define XAE_OPTION_FCS_STRIP			BIT(5)
 
 /* Generate FCS field and add PAD automatically for outgoing frames.
  * Default: enabled (set)
  */
-#define XAE_OPTION_FCS_INSERT			(1 << 6)
+#define XAE_OPTION_FCS_INSERT			BIT(6)
 
 /* Enable Length/Type error checking for incoming frames. When this option is
  * set, the MAC will filter frames that have a mismatched type/length field
@@ -55,13 +68,13 @@
  * types of frames are encountered. When this option is cleared, the MAC will
  * allow these types of frames to be received. Default: enabled (set)
  */
-#define XAE_OPTION_LENTYPE_ERR			(1 << 7)
+#define XAE_OPTION_LENTYPE_ERR			BIT(7)
 
 /* Enable the transmitter. Default: enabled (set) */
-#define XAE_OPTION_TXEN				(1 << 11)
+#define XAE_OPTION_TXEN				BIT(11)
 
 /*  Enable the receiver. Default: enabled (set) */
-#define XAE_OPTION_RXEN				(1 << 12)
+#define XAE_OPTION_RXEN				BIT(12)
 
 /*  Default options set when device is initialized or reset */
 #define XAE_OPTION_DEFAULTS				   \
@@ -122,7 +135,7 @@
 /* Default TX/RX Threshold and waitbound values for SGDMA mode */
 #define XAXIDMA_DFT_TX_THRESHOLD	24
 #define XAXIDMA_DFT_TX_WAITBOUND	254
-#define XAXIDMA_DFT_RX_THRESHOLD	24
+#define XAXIDMA_DFT_RX_THRESHOLD	1
 #define XAXIDMA_DFT_RX_WAITBOUND	254
 
 #define XAXIDMA_BD_CTRL_TXSOF_MASK	0x08000000 /* First tx packet */
@@ -141,6 +154,24 @@
 
 #define XAXIDMA_BD_MINIMUM_ALIGNMENT	0x40
 
+/* AXI Tx Timestamp Stream FIFO Register Definitions */
+#define XAXIFIFO_TXTS_ISR	0x00000000 /* Interrupt Status Register */
+#define XAXIFIFO_TXTS_TDFV	0x0000000C /* Transmit Data FIFO Vacancy */
+#define XAXIFIFO_TXTS_TXFD	0x00000010 /* Tx Data Write Port */
+#define XAXIFIFO_TXTS_TLR	0x00000014 /* Transmit Length Register */
+#define XAXIFIFO_TXTS_RFO	0x0000001C /* Rx Fifo Occupancy */
+#define XAXIFIFO_TXTS_RDFR	0x00000018 /* Rx Fifo reset */
+#define XAXIFIFO_TXTS_RXFD	0x00000020 /* Rx Data Read Port */
+#define XAXIFIFO_TXTS_RLR	0x00000024 /* Receive Length Register */
+#define XAXIFIFO_TXTS_SRR	0x00000028 /* AXI4-Stream Reset */
+
+#define XAXIFIFO_TXTS_INT_RC_MASK	0x04000000
+#define XAXIFIFO_TXTS_RXFD_MASK		0x7FFFFFFF
+#define XAXIFIFO_TXTS_RESET_MASK	0x000000A5
+#define XAXIFIFO_TXTS_TAG_MASK		0xFFFF0000
+#define XAXIFIFO_TXTS_TAG_SHIFT		16
+#define XAXIFIFO_TXTS_TAG_MAX		0xFFFE
+
 /* Axi Ethernet registers definition */
 #define XAE_RAF_OFFSET		0x00000000 /* Reset and Address filter */
 #define XAE_TPF_OFFSET		0x00000004 /* Tx Pause Frame */
@@ -159,16 +190,18 @@
 #define XAE_RCW1_OFFSET		0x00000404 /* Rx Configuration Word 1 */
 #define XAE_TC_OFFSET		0x00000408 /* Tx Configuration */
 #define XAE_FCC_OFFSET		0x0000040C /* Flow Control Configuration */
-#define XAE_EMMC_OFFSET		0x00000410 /* EMAC mode configuration */
-#define XAE_PHYC_OFFSET		0x00000414 /* RGMII/SGMII configuration */
+#define XAE_EMMC_OFFSET		0x00000410 /* MAC speed configuration */
+#define XAE_PHYC_OFFSET		0x00000414 /* RX Max Frame Configuration */
 #define XAE_ID_OFFSET		0x000004F8 /* Identification register */
-#define XAE_MDIO_MC_OFFSET	0x00000500 /* MII Management Config */
-#define XAE_MDIO_MCR_OFFSET	0x00000504 /* MII Management Control */
-#define XAE_MDIO_MWD_OFFSET	0x00000508 /* MII Management Write Data */
-#define XAE_MDIO_MRD_OFFSET	0x0000050C /* MII Management Read Data */
+#define XAE_RMFC_OFFSET		0x00000414 /* RX Max Frame Configuration */
+#define XAE_MDIO_MC_OFFSET	0x00000500 /* MDIO Setup */
+#define XAE_MDIO_MCR_OFFSET	0x00000504 /* MDIO Control */
+#define XAE_MDIO_MWD_OFFSET	0x00000508 /* MDIO Write Data */
+#define XAE_MDIO_MRD_OFFSET	0x0000050C /* MDIO Read Data */
 #define XAE_UAW0_OFFSET		0x00000700 /* Unicast address word 0 */
 #define XAE_UAW1_OFFSET		0x00000704 /* Unicast address word 1 */
-#define XAE_FMI_OFFSET		0x00000708 /* Filter Mask Index */
+#define XAE_FMI_OFFSET		0x00000708 /* Frame Filter Control */
+#define XAE_FFE_OFFSET		0x0000070C /* Frame Filter Enable */
 #define XAE_AF0_OFFSET		0x00000710 /* Address Filter 0 */
 #define XAE_AF1_OFFSET		0x00000714 /* Address Filter 1 */
 
@@ -229,6 +262,7 @@
 #define XAE_TPID_3_MASK		0xFFFF0000 /* TPID 1 */
 
 /* Bit masks for Axi Ethernet RCW1 register */
+#define XAE_RCW1_INBAND1588_MASK 0x00400000 /* Inband 1588 Enable */
 #define XAE_RCW1_RST_MASK	0x80000000 /* Reset */
 #define XAE_RCW1_JUM_MASK	0x40000000 /* Jumbo frame enable */
 /* In-Band FCS enable (FCS not stripped) */
@@ -245,6 +279,7 @@
 #define XAE_RCW1_PAUSEADDR_MASK 0x0000FFFF
 
 /* Bit masks for Axi Ethernet TC register */
+#define XAE_TC_INBAND1588_MASK 0x00400000 /* Inband 1588 Enable */
 #define XAE_TC_RST_MASK		0x80000000 /* Reset */
 #define XAE_TC_JUM_MASK		0x40000000 /* Jumbo frame enable */
 /* In-Band FCS enable (FCS not generated) */
@@ -269,6 +304,7 @@
 #define XAE_EMMC_LINKSPD_10	0x00000000 /* Link Speed mask for 10 Mbit */
 #define XAE_EMMC_LINKSPD_100	0x40000000 /* Link Speed mask for 100 Mbit */
 #define XAE_EMMC_LINKSPD_1000	0x80000000 /* Link Speed mask for 1000 Mbit */
+#define XAE_EMMC_LINKSPD_2500	0x80000000 /* Link Speed mask for 2500 Mbit */
 
 /* Bit masks for Axi Ethernet PHYC register */
 #define XAE_PHYC_SGMIILINKSPEED_MASK	0xC0000000 /* SGMII link speed mask*/
@@ -307,29 +343,21 @@
  */
 #define XAE_UAW1_UNICASTADDR_MASK	0x0000FFFF
 
-/* Bit masks for Axi Ethernet FMI register */
+/* Bit masks for Axi Ethernet FMC register */
 #define XAE_FMI_PM_MASK			0x80000000 /* Promis. mode enable */
 #define XAE_FMI_IND_MASK		0x00000003 /* Index Mask */
 
 #define XAE_MDIO_DIV_DFT		29 /* Default MDIO clock divisor */
 
-/* Defines for different options for C_PHY_TYPE parameter in Axi Ethernet IP */
-#define XAE_PHY_TYPE_MII		0
-#define XAE_PHY_TYPE_GMII		1
-#define XAE_PHY_TYPE_RGMII_1_3		2
-#define XAE_PHY_TYPE_RGMII_2_0		3
-#define XAE_PHY_TYPE_SGMII		4
-#define XAE_PHY_TYPE_1000BASE_X		5
-
- /* Total number of entries in the hardware multicast table. */
+/* Total number of entries in the hardware multicast table. */
 #define XAE_MULTICAST_CAM_TABLE_NUM	4
 
 /* Axi Ethernet Synthesis features */
-#define XAE_FEATURE_PARTIAL_RX_CSUM	(1 << 0)
-#define XAE_FEATURE_PARTIAL_TX_CSUM	(1 << 1)
-#define XAE_FEATURE_FULL_RX_CSUM	(1 << 2)
-#define XAE_FEATURE_FULL_TX_CSUM	(1 << 3)
-#define XAE_FEATURE_DMA_64BIT		(1 << 4)
+#define XAE_FEATURE_PARTIAL_RX_CSUM	BIT(0)
+#define XAE_FEATURE_PARTIAL_TX_CSUM	BIT(1)
+#define XAE_FEATURE_FULL_RX_CSUM	BIT(2)
+#define XAE_FEATURE_FULL_TX_CSUM	BIT(3)
+#define XAE_FEATURE_DMA_64BIT		BIT(4)
 
 #define XAE_NO_CSUM_OFFLOAD		0
 
@@ -339,16 +367,228 @@
 
 #define DELAY_OF_ONE_MILLISEC		1000
 
-/* Xilinx PCS/PMA PHY register for switching 1000BaseX or SGMII */
-#define XLNX_MII_STD_SELECT_REG		0x11
-#define XLNX_MII_STD_SELECT_SGMII	BIT(0)
+#define XAXIENET_NAPI_WEIGHT		64
 
+/* Definition of 1588 PTP in Axi Ethernet IP */
+#define TX_TS_OP_NOOP           0x0
+#define TX_TS_OP_ONESTEP        0x1
+#define TX_TS_OP_TWOSTEP        0x2
+#define TX_TS_CSUM_UPDATE       0x1
+#define TX_TS_CSUM_UPDATE_MRMAC		0x4
+#define TX_TS_PDELAY_UPDATE_MRMAC	0x8
+#define TX_PTP_CSUM_OFFSET      0x28
+#define TX_PTP_TS_OFFSET        0x4C
+#define TX_PTP_CF_OFFSET        0x32
+
+/* XXV MAC Register Definitions */
+#define XXV_GT_RESET_OFFSET		0x00000000
+#define XXV_TC_OFFSET			0x0000000C
+#define XXV_RCW1_OFFSET			0x00000014
+#define XXV_JUM_OFFSET			0x00000018
+#define XXV_TICKREG_OFFSET		0x00000020
+#define XXV_STATRX_BLKLCK_OFFSET	0x0000040C
+#define XXV_USXGMII_AN_OFFSET		0x000000C8
+#define XXV_USXGMII_AN_STS_OFFSET	0x00000458
+#define XXV_STAT_GTWIZ_OFFSET		0x000004A0
+#define XXV_CONFIG_REVISION		0x00000024
+
+/* XXV MAC Register Mask Definitions */
+#define XXV_GT_RESET_MASK	BIT(0)
+#define XXV_TC_TX_MASK		BIT(0)
+#define XXV_RCW1_RX_MASK	BIT(0)
+#define XXV_RCW1_FCS_MASK	BIT(1)
+#define XXV_TC_FCS_MASK		BIT(1)
+#define XXV_MIN_JUM_MASK	GENMASK(7, 0)
+#define XXV_MAX_JUM_MASK	GENMASK(10, 8)
+#define XXV_RX_BLKLCK_MASK	BIT(0)
+#define XXV_TICKREG_STATEN_MASK BIT(0)
+#define XXV_MAC_MIN_PKT_LEN	64
+#define XXV_GTWIZ_RESET_DONE	(BIT(0) | BIT(1))
+#define XXV_MAJ_MASK		GENMASK(7, 0)
+#define XXV_MIN_MASK		GENMASK(15, 8)
+
+/* USXGMII Register Mask Definitions  */
+#define USXGMII_AN_EN		BIT(5)
+#define USXGMII_AN_RESET	BIT(6)
+#define USXGMII_AN_RESTART	BIT(7)
+#define USXGMII_EN		BIT(16)
+#define USXGMII_RATE_MASK	0x0E000700
+#define USXGMII_RATE_1G		0x04000200
+#define USXGMII_RATE_2G5	0x08000400
+#define USXGMII_RATE_10M	0x0
+#define USXGMII_RATE_100M	0x02000100
+#define USXGMII_RATE_5G		0x0A000500
+#define USXGMII_RATE_10G	0x06000300
+#define USXGMII_FD		BIT(28)
+#define USXGMII_LINK_STS	BIT(31)
+
+/* USXGMII AN STS register mask definitions */
+#define USXGMII_AN_STS_COMP_MASK	BIT(16)
+
+/* MCDMA Register Definitions */
+#define XMCDMA_CR_OFFSET	0x00
+#define XMCDMA_SR_OFFSET	0x04
+#define XMCDMA_CHEN_OFFSET	0x08
+#define XMCDMA_CHSER_OFFSET	0x0C
+#define XMCDMA_ERR_OFFSET	0x10
+#define XMCDMA_PKTDROP_OFFSET	0x14
+#define XMCDMA_TXWEIGHT0_OFFSET 0x18
+#define XMCDMA_TXWEIGHT1_OFFSET 0x1C
+#define XMCDMA_RXINT_SER_OFFSET 0x20
+#define XMCDMA_TXINT_SER_OFFSET 0x28
+
+#define XMCDMA_CHOBS1_OFFSET	0x440
+#define XMCDMA_CHOBS2_OFFSET	0x444
+#define XMCDMA_CHOBS3_OFFSET	0x448
+#define XMCDMA_CHOBS4_OFFSET	0x44C
+#define XMCDMA_CHOBS5_OFFSET	0x450
+#define XMCDMA_CHOBS6_OFFSET	0x454
+
+#define XMCDMA_CHAN_RX_OFFSET  0x500
+
+/* Per Channel Registers */
+#define XMCDMA_CHAN_CR_OFFSET(chan_id)		(0x40 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_SR_OFFSET(chan_id)		(0x44 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_CURDESC_OFFSET(chan_id)	(0x48 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_TAILDESC_OFFSET(chan_id)	(0x50 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_PKTDROP_OFFSET(chan_id)	(0x58 + ((chan_id) - 1) * 0x40)
+
+#define XMCDMA_RX_OFFSET	0x500
+
+/* MCDMA Mask registers */
+#define XMCDMA_CR_RUNSTOP_MASK		BIT(0) /* Start/stop DMA channel */
+#define XMCDMA_CR_RESET_MASK		BIT(2) /* Reset DMA engine */
+
+#define XMCDMA_SR_HALTED_MASK		BIT(0)
+#define XMCDMA_SR_IDLE_MASK		BIT(1)
+
+#define XMCDMA_IRQ_ERRON_OTHERQ_MASK	BIT(3)
+#define XMCDMA_IRQ_PKTDROP_MASK		BIT(4)
+#define XMCDMA_IRQ_IOC_MASK		BIT(5)
+#define XMCDMA_IRQ_DELAY_MASK		BIT(6)
+#define XMCDMA_IRQ_ERR_MASK		BIT(7)
+#define XMCDMA_IRQ_ALL_MASK		GENMASK(7, 5)
+#define XMCDMA_PKTDROP_COALESCE_MASK	GENMASK(15, 8)
+#define XMCDMA_COALESCE_MASK		GENMASK(23, 16)
+#define XMCDMA_DELAY_MASK		GENMASK(31, 24)
+
+#define XMCDMA_CHEN_MASK		GENMASK(7, 0)
+#define XMCDMA_CHID_MASK		GENMASK(7, 0)
+
+#define XMCDMA_ERR_INTERNAL_MASK	BIT(0)
+#define XMCDMA_ERR_SLAVE_MASK		BIT(1)
+#define XMCDMA_ERR_DECODE_MASK		BIT(2)
+#define XMCDMA_ERR_SG_INT_MASK		BIT(4)
+#define XMCDMA_ERR_SG_SLV_MASK		BIT(5)
+#define XMCDMA_ERR_SG_DEC_MASK		BIT(6)
+
+#define XMCDMA_PKTDROP_CNT_MASK		GENMASK(31, 0)
+
+#define XMCDMA_BD_CTRL_TXSOF_MASK	0x80000000 /* First tx packet */
+#define XMCDMA_BD_CTRL_TXEOF_MASK	0x40000000 /* Last tx packet */
+#define XMCDMA_BD_CTRL_ALL_MASK		0xC0000000 /* All control bits */
+#define XMCDMA_BD_STS_ALL_MASK		0xF0000000 /* All status bits */
+
+#define XMCDMA_COALESCE_SHIFT		16
+#define XMCDMA_DELAY_SHIFT		24
+#define XMCDMA_DFT_TX_THRESHOLD		1
+
+#define XMCDMA_TXWEIGHT_CH_MASK(chan_id)	GENMASK(((chan_id) * 4 + 3), \
+							(chan_id) * 4)
+#define XMCDMA_TXWEIGHT_CH_SHIFT(chan_id)	((chan_id) * 4)
+
+/* PTP Packet length */
+#define XAE_TX_PTP_LEN		16
+#define XXV_TX_PTP_LEN		12
+
+/* Macros used when AXI DMA h/w is configured without DRE */
+#define XAE_TX_BUFFERS		64
+#define XAE_MAX_PKT_LEN		8192
+
+/* MRMAC Register Definitions */
+/* Configuration Registers */
+#define MRMAC_REV_OFFSET		0x00000000
+#define MRMAC_RESET_OFFSET		0x00000004
+#define MRMAC_MODE_OFFSET		0x00000008
+#define MRMAC_CONFIG_TX_OFFSET		0x0000000C
+#define MRMAC_CONFIG_RX_OFFSET		0x00000010
+#define MRMAC_TICK_OFFSET		0x0000002C
+#define MRMAC_CFG1588_OFFSET	0x00000040
+
+/* Status Registers */
+#define MRMAC_TX_STS_OFFSET		0x00000740
+#define MRMAC_RX_STS_OFFSET		0x00000744
+#define MRMAC_TX_RT_STS_OFFSET		0x00000748
+#define MRMAC_RX_RT_STS_OFFSET		0x0000074C
+#define MRMAC_STATRX_BLKLCK_OFFSET	0x00000754
+#define MRMAC_STATRX_VALID_CTRL_OFFSET	0x000007B8
+
+/* Register bit masks */
+#define MRMAC_RX_SERDES_RST_MASK	(BIT(3) | BIT(2) | BIT(1) | BIT(0))
+#define MRMAC_TX_SERDES_RST_MASK	BIT(4)
+#define MRMAC_RX_RST_MASK		BIT(5)
+#define MRMAC_TX_RST_MASK		BIT(6)
+#define MRMAC_RX_AXI_RST_MASK		BIT(8)
+#define MRMAC_TX_AXI_RST_MASK		BIT(9)
+#define MRMAC_STS_ALL_MASK		0xFFFFFFFF
+
+#define MRMAC_RX_EN_MASK		BIT(0)
+#define MRMAC_RX_DEL_FCS_MASK		BIT(1)
+
+#define MRMAC_TX_EN_MASK		BIT(0)
+#define MRMAC_TX_INS_FCS_MASK		BIT(1)
+
+#define MRMAC_RX_BLKLCK_MASK		BIT(0)
+#define MRMAC_RX_STATUS_MASK		BIT(0)
+#define MRMAC_RX_VALID_MASK		BIT(0)
+
+#define MRMAC_CTL_DATA_RATE_MASK	GENMASK(2, 0)
+#define MRMAC_CTL_DATA_RATE_10G		0
+#define MRMAC_CTL_DATA_RATE_25G		1
+#define MRMAC_CTL_DATA_RATE_40G		2
+#define MRMAC_CTL_DATA_RATE_50G		3
+#define MRMAC_CTL_DATA_RATE_100G	4
+
+#define MRMAC_CTL_AXIS_CFG_MASK		GENMASK(11, 9)
+#define MRMAC_CTL_AXIS_CFG_SHIFT	9
+#define MRMAC_CTL_AXIS_CFG_10G_IND	1
+#define MRMAC_CTL_AXIS_CFG_25G_IND	1
+
+#define MRMAC_CTL_SERDES_WIDTH_MASK	GENMASK(6, 4)
+#define MRMAC_CTL_SERDES_WIDTH_SHIFT	4
+#define MRMAC_CTL_SERDES_WIDTH_10G	4
+#define MRMAC_CTL_SERDES_WIDTH_25G	6
+
+#define MRMAC_CTL_RATE_CFG_MASK		(MRMAC_CTL_DATA_RATE_MASK |	\
+					 MRMAC_CTL_AXIS_CFG_MASK |	\
+					 MRMAC_CTL_SERDES_WIDTH_MASK)
+
+#define MRMAC_CTL_PM_TICK_MASK		BIT(30)
+#define MRMAC_TICK_TRIGGER		BIT(0)
+#define MRMAC_ONE_STEP_EN		BIT(0)
+
+/* MRMAC GT wrapper registers */
+#define MRMAC_GT_PLL_OFFSET		0x0
+#define MRMAC_GT_PLL_STS_OFFSET		0x8
+#define MRMAC_GT_RATE_OFFSET		0x0
+#define MRMAC_GT_CTRL_OFFSET		0x8
+
+#define MRMAC_GT_PLL_RST_MASK		0x00030003
+#define MRMAC_GT_PLL_DONE_MASK		0xFF
+#define MRMAC_GT_RST_ALL_MASK		BIT(0)
+#define MRMAC_GT_RST_RX_MASK		BIT(1)
+#define MRMAC_GT_RST_TX_MASK		BIT(2)
+#define MRMAC_GT_10G_MASK		0x00000001
+#define MRMAC_GT_25G_MASK		0x00000002
+
+#define MRMAC_GT_LANE_OFFSET		BIT(16)
+#define MRMAC_MAX_GT_LANES		4
 /**
  * struct axidma_bd - Axi Dma buffer descriptor layout
  * @next:         MM2S/S2MM Next Descriptor Pointer
- * @next_msb:     MM2S/S2MM Next Descriptor Pointer (high 32 bits)
+ * @reserved1:    Reserved and not used for 32-bit
  * @phys:         MM2S/S2MM Buffer Address
- * @phys_msb:     MM2S/S2MM Buffer Address (high 32 bits)
+ * @reserved2:    Reserved and not used for 32-bit
  * @reserved3:    Reserved and not used
  * @reserved4:    Reserved and not used
  * @cntrl:        MM2S/S2MM Control value
@@ -358,12 +598,23 @@
  * @app2:         MM2S/S2MM User Application Field 2.
  * @app3:         MM2S/S2MM User Application Field 3.
  * @app4:         MM2S/S2MM User Application Field 4.
+ * @sw_id_offset: MM2S/S2MM Sw ID
+ * @ptp_tx_skb:   If timestamping is enabled used for timestamping skb
+ *		  Otherwise reserved.
+ * @ptp_tx_ts_tag: Tag value of 2 step timestamping if timestamping is enabled
+ *		   Otherwise reserved.
+ * @tx_skb:	  Transmit skb address
+ * @tx_desc_mapping: Tx Descriptor DMA mapping type.
  */
 struct axidma_bd {
-	u32 next;	/* Physical address of next buffer descriptor */
-	u32 next_msb;	/* high 32 bits for IP >= v7.1, reserved on older IP */
-	u32 phys;
-	u32 phys_msb;	/* for IP >= v7.1, reserved for older IP */
+	phys_addr_t next;	/* Physical address of next buffer descriptor */
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved1;
+#endif
+	phys_addr_t phys;
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved2;
+#endif
 	u32 reserved3;
 	u32 reserved4;
 	u32 cntrl;
@@ -372,48 +623,110 @@
 	u32 app1;	/* TX start << 16 | insert */
 	u32 app2;	/* TX csum seed */
 	u32 app3;
-	u32 app4;   /* Last field used by HW */
-	struct sk_buff *skb;
+	u32 app4;
+	phys_addr_t sw_id_offset; /* first unused field by h/w */
+	phys_addr_t ptp_tx_skb;
+	u32 ptp_tx_ts_tag;
+	phys_addr_t tx_skb;
+	u32 tx_desc_mapping;
+} __aligned(XAXIDMA_BD_MINIMUM_ALIGNMENT);
+/**
+ * struct aximcdma_bd - Axi MCDMA buffer descriptor layout
+ * @next:         MM2S/S2MM Next Descriptor Pointer
+ * @reserved1:    Reserved and not used for 32-bit
+ * @phys:         MM2S/S2MM Buffer Address
+ * @reserved2:    Reserved and not used for 32-bit
+ * @reserved3:    Reserved and not used
+ * @cntrl:        MM2S/S2MM Control value
+ * @status:       S2MM Status value
+ * @sband_stats:  S2MM Sideband Status value
+ *		  MM2S Status value
+ * @app0:         MM2S/S2MM User Application Field 0.
+ * @app1:         MM2S/S2MM User Application Field 1.
+ * @app2:         MM2S/S2MM User Application Field 2.
+ * @app3:         MM2S/S2MM User Application Field 3.
+ * @app4:         MM2S/S2MM User Application Field 4.
+ * @sw_id_offset: MM2S/S2MM Sw ID
+ * @ptp_tx_skb:   If timestamping is enabled used for timestamping skb
+ *		  Otherwise reserved.
+ * @ptp_tx_ts_tag: Tag value of 2 step timestamping if timestamping is enabled
+ *		   Otherwise reserved.
+ * @tx_skb:	  Transmit skb address
+ * @tx_desc_mapping: Tx Descriptor DMA mapping type.
+ */
+struct aximcdma_bd {
+	phys_addr_t next;	/* Physical address of next buffer descriptor */
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved1;
+#endif
+	phys_addr_t phys;
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved2;
+#endif
+	u32 reserved3;
+	u32 cntrl;
+	u32 status;
+	u32 sband_stats;
+	u32 app0;
+	u32 app1;	/* TX start << 16 | insert */
+	u32 app2;	/* TX csum seed */
+	u32 app3;
+	u32 app4;
+	phys_addr_t sw_id_offset; /* first unused field by h/w */
+	phys_addr_t ptp_tx_skb;
+	u32 ptp_tx_ts_tag;
+	phys_addr_t tx_skb;
+	u32 tx_desc_mapping;
 } __aligned(XAXIDMA_BD_MINIMUM_ALIGNMENT);
 
 #define XAE_NUM_MISC_CLOCKS 3
+#define DESC_DMA_MAP_SINGLE 0
+#define DESC_DMA_MAP_PAGE 1
+
+#if defined(CONFIG_AXIENET_HAS_MCDMA)
+#define XAE_MAX_QUEUES		16
+#else
+#define XAE_MAX_QUEUES		1
+#endif
 
 /**
  * struct axienet_local - axienet private per device data
  * @ndev:	Pointer for net_device to which it will be attached.
  * @dev:	Pointer to device structure
  * @phy_node:	Pointer to device node structure
- * @phylink:	Pointer to phylink instance
- * @phylink_config: phylink configuration settings
- * @pcs_phy:	Reference to PCS/PMA PHY if used
- * @switch_x_sgmii: Whether switchable 1000BaseX/SGMII mode is enabled in the core
  * @axi_clk:	AXI4-Lite bus clock
  * @misc_clks:	Misc ethernet clocks (AXI4-Stream, Ref, MGT clocks)
  * @mii_bus:	Pointer to MII bus structure
  * @mii_clk_div: MII bus clock divider value
  * @regs_start: Resource start for axienet device addresses
  * @regs:	Base address for the axienet_local device address space
- * @dma_regs:	Base address for the axidma device address space
- * @dma_err_task: Work structure to process Axi DMA errors
- * @tx_irq:	Axidma TX IRQ number
- * @rx_irq:	Axidma RX IRQ number
- * @eth_irq:	Ethernet core IRQ number
+ * @mcdma_regs:	Base address for the aximcdma device address space
+ * @napi:	Napi Structure array for all dma queues
+ * @num_tx_queues: Total number of Tx DMA queues
+ * @num_rx_queues: Total number of Rx DMA queues
+ * @dq:		DMA queues data
  * @phy_mode:	Phy type to identify between MII/GMII/RGMII/SGMII/1000 Base-X
+ * @master:	Master endpoint
+ * @slaves:	Front panel ports
+ * @timer_priv: PTP timer private data pointer
+ * @ptp_tx_irq: PTP tx irq
+ * @ptp_rx_irq: PTP rx irq
+ * @rtc_irq:	PTP RTC irq
+ * @qbv_irq:	QBV shed irq
+ * @ptp_ts_type: ptp time stamp type - 1 or 2 step mode
+ * @ptp_rx_hw_pointer: ptp rx hw pointer
+ * @ptp_rx_sw_pointer: ptp rx sw pointer
+ * @ptp_txq:	PTP tx queue header
+ * @tx_tstamp_work: PTP timestamping work queue
+ * @qbv_regs:	pointer to qbv registers base address
+ * @ptp_tx_lock: PTP tx lock
+ * @dma_err_tasklet: Tasklet structure to process Axi DMA errors
+ * @eth_irq:	Axi Ethernet IRQ number
  * @options:	AxiEthernet option word
+ * @last_link:	Phy link state in which the PHY was negotiated earlier
  * @features:	Stores the extended features supported by the axienet hw
- * @tx_bd_v:	Virtual address of the TX buffer descriptor ring
- * @tx_bd_p:	Physical address(start address) of the TX buffer descr. ring
- * @tx_bd_num:	Size of TX buffer descriptor ring
- * @rx_bd_v:	Virtual address of the RX buffer descriptor ring
- * @rx_bd_p:	Physical address(start address) of the RX buffer descr. ring
- * @rx_bd_num:	Size of RX buffer descriptor ring
- * @tx_bd_ci:	Stores the index of the Tx buffer descriptor in the ring being
- *		accessed currently. Used while alloc. BDs before a TX starts
- * @tx_bd_tail:	Stores the index of the Tx buffer descriptor in the ring being
- *		accessed currently. Used while processing BDs after the TX
- *		completed.
- * @rx_bd_ci:	Stores the index of the Rx buffer descriptor in the ring being
- *		accessed currently.
+ * @tx_bd_num:	Number of TX buffer descriptors.
+ * @rx_bd_num:	Number of RX buffer descriptors.
  * @max_frm_size: Stores the maximum size of the frame that can be that
  *		  Txed/Rxed in the existing hardware. If jumbo option is
  *		  supported, the maximum frame size would be 9k. Else it is
@@ -423,6 +736,34 @@
  * @csum_offload_on_rx_path:	Stores the checksum selection on RX side.
  * @coalesce_count_rx:	Store the irq coalesce on RX side.
  * @coalesce_count_tx:	Store the irq coalesce on TX side.
+ * @phy_flags:	Phy interface flags.
+ * @eth_hasnobuf: Ethernet is configured in Non buf mode.
+ * @eth_hasptp: Ethernet is configured for ptp.
+ * @axienet_config: Ethernet config structure
+ * @tx_ts_regs:	  Base address for the axififo device address space.
+ * @rx_ts_regs:	  Base address for the rx axififo device address space.
+ * @tstamp_config: Hardware timestamp config structure.
+ * @tx_ptpheader: Stores the tx ptp header.
+ * @aclk: AXI4-Lite clock for ethernet and dma.
+ * @eth_sclk: AXI4-Stream interface clock.
+ * @eth_refclk: Stable clock used by signal delay primitives and transceivers.
+ * @eth_dclk: Dynamic Reconfiguration Port(DRP) clock.
+ * @dma_sg_clk: DMA Scatter Gather Clock.
+ * @dma_rx_clk: DMA S2MM Primary Clock.
+ * @dma_tx_clk: DMA MM2S Primary Clock.
+ * @qnum:     Axi Ethernet queue number to be operate on.
+ * @chan_num: MCDMA Channel number to be operate on.
+ * @chan_id:  MCMDA Channel id used in conjunction with weight parameter.
+ * @weight:   MCDMA Channel weight value to be configured for.
+ * @dma_mask: Specify the width of the DMA address space.
+ * @usxgmii_rate: USXGMII PHY speed.
+ * @mrmac_rate: MRMAC speed.
+ * @gt_pll: Common GT PLL mask control register space.
+ * @gt_ctrl: GT speed and reset control register space.
+ * @phc_index: Index to corresponding PTP clock used.
+ * @gt_lane: MRMAC GT lane index used.
+ * @ptp_os_cf: CF TS of PTP PDelay req for one step usage.
+ * @xxv_ip_version: XXV IP version
  */
 struct axienet_local {
 	struct net_device *ndev;
@@ -430,13 +771,6 @@
 
 	struct device_node *phy_node;
 
-	struct phylink *phylink;
-	struct phylink_config phylink_config;
-
-	struct mdio_device *pcs_phy;
-
-	bool switch_x_sgmii;
-
 	struct clk *axi_clk;
 	struct clk_bulk_data misc_clks[XAE_NUM_MISC_CLOCKS];
 
@@ -445,27 +779,26 @@
 
 	resource_size_t regs_start;
 	void __iomem *regs;
-	void __iomem *dma_regs;
+	void __iomem *mcdma_regs;
 
-	struct work_struct dma_err_task;
+	struct tasklet_struct dma_err_tasklet[XAE_MAX_QUEUES];
+	struct napi_struct napi[XAE_MAX_QUEUES];	/* NAPI Structure */
+
+	u16    num_tx_queues;	/* Number of TX DMA queues */
+	u16    num_rx_queues;	/* Number of RX DMA queues */
+	struct axienet_dma_q *dq[XAE_MAX_QUEUES];	/* DMA queue data*/
 
-	int tx_irq;
-	int rx_irq;
-	int eth_irq;
 	phy_interface_t phy_mode;
 
-	u32 options;
+	spinlock_t ptp_tx_lock;		/* PTP tx lock*/
+	int eth_irq;
+
+	u32 options;			/* Current options word */
+	u32 last_link;
 	u32 features;
 
-	struct axidma_bd *tx_bd_v;
-	dma_addr_t tx_bd_p;
-	u32 tx_bd_num;
-	struct axidma_bd *rx_bd_v;
-	dma_addr_t rx_bd_p;
+	u16 tx_bd_num;
 	u32 rx_bd_num;
-	u32 tx_bd_ci;
-	u32 tx_bd_tail;
-	u32 rx_bd_ci;
 
 	u32 max_frm_size;
 	u32 rxmem;
@@ -475,10 +808,150 @@
 
 	u32 coalesce_count_rx;
 	u32 coalesce_count_tx;
+	u32 phy_flags;
+	bool eth_hasnobuf;
+	bool eth_hasptp;
+	const struct axienet_config *axienet_config;
+
+#if defined(CONFIG_XILINX_AXI_EMAC_HWTSTAMP)
+	void __iomem *tx_ts_regs;
+	void __iomem *rx_ts_regs;
+	struct hwtstamp_config tstamp_config;
+	u8 *tx_ptpheader;
+#endif
+	struct clk *aclk;
+	struct clk *eth_sclk;
+	struct clk *eth_refclk;
+	struct clk *eth_dclk;
+	struct clk *dma_sg_clk;
+	struct clk *dma_rx_clk;
+	struct clk *dma_tx_clk;
+
+	/* MCDMA Fields */
+	int qnum[XAE_MAX_QUEUES];
+	int chan_num[XAE_MAX_QUEUES];
+	/* WRR Fields */
+	u16 chan_id;
+	u16 weight;
+
+	u8 dma_mask;
+	u32 usxgmii_rate;
+
+	u32 mrmac_rate;		/* MRMAC speed */
+	void __iomem *gt_pll;	/* Common GT PLL mask control register space */
+	void __iomem *gt_ctrl;	/* GT speed and reset control register space */
+	u32 phc_index;		/* Index to corresponding PTP clock used  */
+	u32 gt_lane;		/* MRMAC GT lane index used */
+	u64 ptp_os_cf;		/* CF TS of PTP PDelay req for one step usage */
+	u32 xxv_ip_version;
+};
+
+/**
+ * struct axienet_dma_q - axienet private per dma queue data
+ * @lp:		Parent pointer
+ * @dma_regs:	Base address for the axidma device address space
+ * @tx_irq:	Axidma TX IRQ number
+ * @rx_irq:	Axidma RX IRQ number
+ * @tx_lock:	Spin lock for tx path
+ * @rx_lock:	Spin lock for tx path
+ * @tx_bd_v:	Virtual address of the TX buffer descriptor ring
+ * @tx_bd_p:	Physical address(start address) of the TX buffer descr. ring
+ * @rx_bd_v:	Virtual address of the RX buffer descriptor ring
+ * @rx_bd_p:	Physical address(start address) of the RX buffer descr. ring
+ * @tx_buf:	Virtual address of the Tx buffer pool used by the driver when
+ *		DMA h/w is configured without DRE.
+ * @tx_bufs:	Virutal address of the Tx buffer address.
+ * @tx_bufs_dma: Physical address of the Tx buffer address used by the driver
+ *		 when DMA h/w is configured without DRE.
+ * @eth_hasdre: Tells whether DMA h/w is configured with dre or not.
+ * @tx_bd_ci:	Stores the index of the Tx buffer descriptor in the ring being
+ *		accessed currently. Used while alloc. BDs before a TX starts
+ * @tx_bd_tail:	Stores the index of the Tx buffer descriptor in the ring being
+ *		accessed currently. Used while processing BDs after the TX
+ *		completed.
+ * @rx_bd_ci:	Stores the index of the Rx buffer descriptor in the ring being
+ *		accessed currently.
+ * @flags:      MCDMA management channel flags
+ * @chan_id:    MCDMA channel to operate on.
+ * @rx_offset:	MCDMA S2MM channel starting offset.
+ * @txq_bd_v:	Virtual address of the MCDMA TX buffer descriptor ring
+ * @rxq_bd_v:	Virtual address of the MCDMA RX buffer descriptor ring
+ * @tx_packets: Number of transmit packets processed by the dma queue.
+ * @tx_bytes:   Number of transmit bytes processed by the dma queue.
+ * @rx_packets: Number of receive packets processed by the dma queue.
+ * @rx_bytes:	Number of receive bytes processed by the dma queue.
+ */
+struct axienet_dma_q {
+	struct axienet_local	*lp; /* parent */
+	void __iomem *dma_regs;
+
+	int tx_irq;
+	int rx_irq;
+
+	spinlock_t tx_lock;		/* tx lock */
+	spinlock_t rx_lock;		/* rx lock */
+
+	/* Buffer descriptors */
+	struct axidma_bd *tx_bd_v;
+	struct axidma_bd *rx_bd_v;
+	dma_addr_t rx_bd_p;
+	dma_addr_t tx_bd_p;
+
+	unsigned char *tx_buf[XAE_TX_BUFFERS];
+	unsigned char *tx_bufs;
+	dma_addr_t tx_bufs_dma;
+	bool eth_hasdre;
+
+	u32 tx_bd_ci;
+	u32 rx_bd_ci;
+	u32 tx_bd_tail;
+
+	/* MCDMA fields */
+	u16 chan_id;
+	u32 rx_offset;
+	struct aximcdma_bd *txq_bd_v;
+	struct aximcdma_bd *rxq_bd_v;
+
+	unsigned long tx_packets;
+	unsigned long tx_bytes;
+	unsigned long rx_packets;
+	unsigned long rx_bytes;
+};
+
+#define AXIENET_ETHTOOLS_SSTATS_LEN 6
+#define AXIENET_TX_SSTATS_LEN(lp) ((lp)->num_tx_queues * 2)
+#define AXIENET_RX_SSTATS_LEN(lp) ((lp)->num_rx_queues * 2)
+
+/**
+ * enum axienet_ip_type - AXIENET IP/MAC type.
+ *
+ * @XAXIENET_1G:	 IP is 1G MAC
+ * @XAXIENET_2_5G:	 IP type is 2.5G MAC.
+ * @XAXIENET_LEGACY_10G: IP type is legacy 10G MAC.
+ * @XAXIENET_10G_25G:	 IP type is 10G/25G MAC(XXV MAC).
+ * @XAXIENET_MRMAC:	 IP type is hardened Multi Rate MAC (MRMAC).
+ *
+ */
+enum axienet_ip_type {
+	XAXIENET_1G = 0,
+	XAXIENET_2_5G,
+	XAXIENET_LEGACY_10G,
+	XAXIENET_10G_25G,
+	XAXIENET_MRMAC,
+};
+
+struct axienet_config {
+	enum axienet_ip_type mactype;
+	void (*setoptions)(struct net_device *ndev, u32 options);
+	int (*clk_init)(struct platform_device *pdev, struct clk **axi_aclk,
+			struct clk **axis_clk, struct clk **ref_clk,
+			struct clk **dclk);
+	u32 tx_ptplen;
+	u8 ts_header_len;
 };
 
 /**
- * struct axiethernet_option - Used to set axi ethernet hardware options
+ * struct axienet_option - Used to set axi ethernet hardware options
  * @opt:	Option to be set.
  * @reg:	Register offset to be written for setting the option
  * @m_or:	Mask to be ORed for setting the option in the register
@@ -489,6 +962,17 @@
 	u32 m_or;
 };
 
+struct xxvenet_option {
+	u32 opt;
+	u32 reg;
+	u32 m_or;
+};
+
+extern void __iomem *mrmac_gt_pll;
+extern void __iomem *mrmac_gt_ctrl;
+extern int mrmac_pll_reg;
+extern int mrmac_pll_rst;
+
 /**
  * axienet_ior - Memory mapped Axi Ethernet register read
  * @lp:         Pointer to axienet local structure
@@ -508,18 +992,6 @@
 	return axienet_ior(lp, XAE_MDIO_MCR_OFFSET);
 }
 
-static inline void axienet_lock_mii(struct axienet_local *lp)
-{
-	if (lp->mii_bus)
-		mutex_lock(&lp->mii_bus->mdio_lock);
-}
-
-static inline void axienet_unlock_mii(struct axienet_local *lp)
-{
-	if (lp->mii_bus)
-		mutex_unlock(&lp->mii_bus->mdio_lock);
-}
-
 /**
  * axienet_iow - Memory mapped Axi Ethernet register write
  * @lp:         Pointer to axienet local structure
@@ -535,10 +1007,195 @@
 	iowrite32(value, lp->regs + offset);
 }
 
+/**
+ * axienet_get_mrmac_blocklock - Write to Clear MRMAC RX block lock status register
+ * and read the latest status
+ * @lp:         Pointer to axienet local structure
+ *
+ * Return: The contents of the Contents of MRMAC RX block lock status register
+ */
+
+static inline u32 axienet_get_mrmac_blocklock(struct axienet_local *lp)
+{
+	axienet_iow(lp, MRMAC_STATRX_BLKLCK_OFFSET, MRMAC_STS_ALL_MASK);
+	return axienet_ior(lp, MRMAC_STATRX_BLKLCK_OFFSET);
+}
+
+/**
+ * axienet_get_mrmac_rx_status - Write to Clear MRMAC RX status register
+ * and read the latest status
+ * @lp:		Pointer to axienet local structure
+ *
+ * Return: The contents of the Contents of MRMAC RX status register
+ */
+
+static inline u32 axienet_get_mrmac_rx_status(struct axienet_local *lp)
+{
+	axienet_iow(lp, MRMAC_RX_STS_OFFSET, MRMAC_STS_ALL_MASK);
+	return axienet_ior(lp, MRMAC_RX_STS_OFFSET);
+}
+
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+/**
+ * axienet_txts_ior - Memory mapped AXI FIFO MM S register read
+ * @lp:         Pointer to axienet_local structure
+ * @reg:     Address offset from the base address of AXI FIFO MM S
+ *              core
+ *
+ * Return: the contents of the AXI FIFO MM S register
+ */
+
+static inline u32 axienet_txts_ior(struct axienet_local *lp, off_t reg)
+{
+	return ioread32(lp->tx_ts_regs + reg);
+}
+
+/**
+ * axienet_txts_iow - Memory mapper AXI FIFO MM S register write
+ * @lp:         Pointer to axienet_local structure
+ * @reg:     Address offset from the base address of AXI FIFO MM S
+ *              core.
+ * @value:      Value to be written into the AXI FIFO MM S register
+ */
+static inline void axienet_txts_iow(struct  axienet_local *lp, off_t reg,
+				    u32 value)
+{
+	iowrite32(value, (lp->tx_ts_regs + reg));
+}
+
+/**
+ * axienet_rxts_ior - Memory mapped AXI FIFO MM S register read
+ * @lp:         Pointer to axienet_local structure
+ * @reg:     Address offset from the base address of AXI FIFO MM S
+ *              core
+ *
+ * Return: the contents of the AXI FIFO MM S register
+ */
+
+static inline u32 axienet_rxts_ior(struct axienet_local *lp, off_t reg)
+{
+	return ioread32(lp->rx_ts_regs + reg);
+}
+
+/**
+ * axienet_rxts_iow - Memory mapper AXI FIFO MM S register write
+ * @lp:         Pointer to axienet_local structure
+ * @reg:     Address offset from the base address of AXI FIFO MM S
+ *              core.
+ * @value:      Value to be written into the AXI FIFO MM S register
+ */
+static inline void axienet_rxts_iow(struct  axienet_local *lp, off_t reg,
+				    u32 value)
+{
+	iowrite32(value, (lp->rx_ts_regs + reg));
+}
+#endif
+
+/**
+ * axienet_dma_in32 - Memory mapped Axi DMA register read
+ * @q:		Pointer to DMA queue structure
+ * @reg:	Address offset from the base address of the Axi DMA core
+ *
+ * Return: The contents of the Axi DMA register
+ *
+ * This function returns the contents of the corresponding Axi DMA register.
+ */
+static inline u32 axienet_dma_in32(struct axienet_dma_q *q, off_t reg)
+{
+	return ioread32(q->dma_regs + reg);
+}
+
+/**
+ * axienet_dma_out32 - Memory mapped Axi DMA register write.
+ * @q:		Pointer to DMA queue structure
+ * @reg:	Address offset from the base address of the Axi DMA core
+ * @value:	Value to be written into the Axi DMA register
+ *
+ * This function writes the desired value into the corresponding Axi DMA
+ * register.
+ */
+static inline void axienet_dma_out32(struct axienet_dma_q *q,
+				     off_t reg, u32 value)
+{
+	iowrite32(value, q->dma_regs + reg);
+}
+
+/**
+ * axienet_dma_bdout - Memory mapped Axi DMA register Buffer Descriptor write.
+ * @q:		Pointer to DMA queue structure
+ * @reg:	Address offset from the base address of the Axi DMA core
+ * @value:	Value to be written into the Axi DMA register
+ *
+ * This function writes the desired value into the corresponding Axi DMA
+ * register.
+ */
+static inline void axienet_dma_bdout(struct axienet_dma_q *q,
+				     off_t reg, dma_addr_t value)
+{
+#if defined(CONFIG_PHYS_ADDR_T_64BIT)
+	writeq(value, (q->dma_regs + reg));
+#else
+	writel(value, (q->dma_regs + reg));
+#endif
+}
 /* Function prototypes visible in xilinx_axienet_mdio.c for other files */
 int axienet_mdio_enable(struct axienet_local *lp);
 void axienet_mdio_disable(struct axienet_local *lp);
 int axienet_mdio_setup(struct axienet_local *lp);
 void axienet_mdio_teardown(struct axienet_local *lp);
+void axienet_adjust_link(struct net_device *ndev);
+
+int axienet_mdio_wait_until_ready(struct axienet_local *lp);
+void __maybe_unused axienet_bd_free(struct net_device *ndev,
+				    struct axienet_dma_q *q);
+int __maybe_unused axienet_dma_q_init(struct net_device *ndev,
+				      struct axienet_dma_q *q);
+void axienet_dma_err_handler(unsigned long data);
+irqreturn_t __maybe_unused axienet_tx_irq(int irq, void *_ndev);
+irqreturn_t __maybe_unused axienet_rx_irq(int irq, void *_ndev);
+void axienet_start_xmit_done(struct net_device *ndev, struct axienet_dma_q *q);
+void axienet_dma_bd_release(struct net_device *ndev);
+void __axienet_device_reset(struct axienet_dma_q *q);
+void axienet_set_mac_address(struct net_device *ndev, const void *address);
+void axienet_set_multicast_list(struct net_device *ndev);
+int xaxienet_rx_poll(struct napi_struct *napi, int quota);
+void axienet_setoptions(struct net_device *ndev, u32 options);
+int axienet_queue_xmit(struct sk_buff *skb, struct net_device *ndev,
+		       u16 map);
+
+#if defined(CONFIG_AXIENET_HAS_MCDMA)
+int __maybe_unused axienet_mcdma_rx_q_init(struct net_device *ndev,
+					   struct axienet_dma_q *q);
+int __maybe_unused axienet_mcdma_tx_q_init(struct net_device *ndev,
+					   struct axienet_dma_q *q);
+void __maybe_unused axienet_mcdma_tx_bd_free(struct net_device *ndev,
+					     struct axienet_dma_q *q);
+void __maybe_unused axienet_mcdma_rx_bd_free(struct net_device *ndev,
+					     struct axienet_dma_q *q);
+irqreturn_t __maybe_unused axienet_mcdma_tx_irq(int irq, void *_ndev);
+irqreturn_t __maybe_unused axienet_mcdma_rx_irq(int irq, void *_ndev);
+void __maybe_unused axienet_mcdma_err_handler(unsigned long data);
+void axienet_strings(struct net_device *ndev, u32 sset, u8 *data);
+int axienet_sset_count(struct net_device *ndev, int sset);
+void axienet_get_stats(struct net_device *ndev,
+		       struct ethtool_stats *stats,
+		       u64 *data);
+int axeinet_mcdma_create_sysfs(struct kobject *kobj);
+void axeinet_mcdma_remove_sysfs(struct kobject *kobj);
+int __maybe_unused axienet_mcdma_tx_probe(struct platform_device *pdev,
+					  struct device_node *np,
+					  struct axienet_local *lp);
+int __maybe_unused axienet_mcdma_rx_probe(struct platform_device *pdev,
+					  struct axienet_local *lp,
+					  struct net_device *ndev);
+#endif
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+void axienet_tx_hwtstamp(struct axienet_local *lp,
+			 struct aximcdma_bd *cur_p);
+#else
+void axienet_tx_hwtstamp(struct axienet_local *lp,
+			 struct axidma_bd *cur_p);
+#endif
 
 #endif /* XILINX_AXI_ENET_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/xilinx_axienet_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/xilinx_axienet_dma.c
@@ -0,0 +1,492 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Xilinx AXI Ethernet (DMA programming)
+ *
+ * Copyright (c) 2008 Nissin Systems Co., Ltd.,  Yoshio Kashiwagi
+ * Copyright (c) 2005-2008 DLA Systems,  David H. Lynch Jr. <dhlii@dlasys.net>
+ * Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
+ * Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
+ * Copyright (c) 2010 - 2011 PetaLogix
+ * Copyright (c) 2010 - 2012 Xilinx, Inc.
+ * Copyright (C) 2018 Xilinx, Inc. All rights reserved.
+ *
+ * This file contains helper functions for AXI DMA TX and RX programming.
+ */
+
+#include "xilinx_axienet.h"
+
+/**
+ * axienet_bd_free - Release buffer descriptor rings for individual dma queue
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * This function is helper function to axienet_dma_bd_release.
+ */
+
+void __maybe_unused axienet_bd_free(struct net_device *ndev,
+				    struct axienet_dma_q *q)
+{
+	int i;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		if (q->rx_bd_v[i].phys)
+			dma_unmap_single(ndev->dev.parent, q->rx_bd_v[i].phys,
+					 lp->max_frm_size, DMA_FROM_DEVICE);
+		dev_kfree_skb((struct sk_buff *)
+			      (q->rx_bd_v[i].sw_id_offset));
+	}
+
+	if (q->rx_bd_v) {
+		dma_free_coherent(ndev->dev.parent,
+				  sizeof(*q->rx_bd_v) * lp->rx_bd_num,
+				  q->rx_bd_v,
+				  q->rx_bd_p);
+	}
+	if (q->tx_bd_v) {
+		dma_free_coherent(ndev->dev.parent,
+				  sizeof(*q->tx_bd_v) * lp->tx_bd_num,
+				  q->tx_bd_v,
+				  q->tx_bd_p);
+	}
+	if (q->tx_bufs) {
+		dma_free_coherent(ndev->dev.parent,
+				  XAE_MAX_PKT_LEN * lp->tx_bd_num,
+				  q->tx_bufs,
+				  q->tx_bufs_dma);
+	}
+}
+
+/**
+ * __dma_txq_init - Setup buffer descriptor rings for individual Axi DMA-Tx
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_q_init
+ */
+static int __dma_txq_init(struct net_device *ndev, struct axienet_dma_q *q)
+{
+	int i;
+	u32 cr;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	q->tx_bd_ci = 0;
+	q->tx_bd_tail = 0;
+
+	q->tx_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					sizeof(*q->tx_bd_v) * lp->tx_bd_num,
+					&q->tx_bd_p, GFP_KERNEL);
+	if (!q->tx_bd_v)
+		goto out;
+
+	for (i = 0; i < lp->tx_bd_num; i++) {
+		q->tx_bd_v[i].next = q->tx_bd_p +
+				     sizeof(*q->tx_bd_v) *
+				     ((i + 1) % lp->tx_bd_num);
+	}
+
+	if (!q->eth_hasdre) {
+		q->tx_bufs = dma_alloc_coherent(ndev->dev.parent,
+						XAE_MAX_PKT_LEN * lp->tx_bd_num,
+						&q->tx_bufs_dma,
+						GFP_KERNEL);
+		if (!q->tx_bufs)
+			goto out;
+
+		for (i = 0; i < lp->tx_bd_num; i++)
+			q->tx_buf[i] = &q->tx_bufs[i * XAE_MAX_PKT_LEN];
+	}
+
+	/* Start updating the Tx channel control register */
+	cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+	/* Update the interrupt coalesce count */
+	cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
+	      ((lp->coalesce_count_tx) << XAXIDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
+	      (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XAXIDMA_IRQ_ALL_MASK;
+	/* Write to the Tx channel control register */
+	axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, cr);
+
+	/* Write to the RS (Run-stop) bit in the Tx channel control register.
+	 * Tx channel is now ready to run. But only after we write to the
+	 * tail pointer register that the Tx channel will start transmitting.
+	 */
+	axienet_dma_bdout(q, XAXIDMA_TX_CDESC_OFFSET, q->tx_bd_p);
+	cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+	axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET,
+			  cr | XAXIDMA_CR_RUNSTOP_MASK);
+	return 0;
+out:
+	return -ENOMEM;
+}
+
+/**
+ * __dma_rxq_init - Setup buffer descriptor rings for individual Axi DMA-Rx
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_q_init
+ */
+static int __dma_rxq_init(struct net_device *ndev,
+			  struct axienet_dma_q *q)
+{
+	int i;
+	u32 cr;
+	struct sk_buff *skb;
+	struct axienet_local *lp = netdev_priv(ndev);
+	/* Reset the indexes which are used for accessing the BDs */
+	q->rx_bd_ci = 0;
+
+	/* Allocate the Rx buffer descriptors. */
+	q->rx_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					sizeof(*q->rx_bd_v) * lp->rx_bd_num,
+					&q->rx_bd_p, GFP_KERNEL);
+	if (!q->rx_bd_v)
+		goto out;
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		q->rx_bd_v[i].next = q->rx_bd_p +
+				     sizeof(*q->rx_bd_v) *
+				     ((i + 1) % lp->rx_bd_num);
+
+		skb = netdev_alloc_skb(ndev, lp->max_frm_size);
+		if (!skb)
+			goto out;
+
+		/* Ensure that the skb is completely updated
+		 * prio to mapping the DMA
+		 */
+		wmb();
+
+		q->rx_bd_v[i].sw_id_offset = (phys_addr_t)skb;
+		q->rx_bd_v[i].phys = dma_map_single(ndev->dev.parent,
+						    skb->data,
+						    lp->max_frm_size,
+						    DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, q->rx_bd_v[i].phys))) {
+			q->rx_bd_v[i].phys = 0;
+			dev_err(&ndev->dev, "axidma map error\n");
+			goto out;
+		}
+		q->rx_bd_v[i].cntrl = lp->max_frm_size;
+	}
+
+	/* Start updating the Rx channel control register */
+	cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+	/* Update the interrupt coalesce count */
+	cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
+	      ((lp->coalesce_count_rx) << XAXIDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = ((cr & ~XAXIDMA_DELAY_MASK) |
+	      (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XAXIDMA_IRQ_ALL_MASK;
+	/* Write to the Rx channel control register */
+	axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+
+	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
+	 * halted state. This will make the Rx side ready for reception.
+	 */
+	axienet_dma_bdout(q, XAXIDMA_RX_CDESC_OFFSET, q->rx_bd_p);
+	cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+	axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET,
+			  cr | XAXIDMA_CR_RUNSTOP_MASK);
+	axienet_dma_bdout(q, XAXIDMA_RX_TDESC_OFFSET, q->rx_bd_p +
+			  (sizeof(*q->rx_bd_v) * (lp->rx_bd_num - 1)));
+
+	return 0;
+out:
+	return -ENOMEM;
+}
+
+/**
+ * axienet_dma_q_init - Setup buffer descriptor rings for individual Axi DMA
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_bd_init
+ */
+int __maybe_unused axienet_dma_q_init(struct net_device *ndev,
+				      struct axienet_dma_q *q)
+{
+	if (__dma_txq_init(ndev, q))
+		goto out;
+
+	if (__dma_rxq_init(ndev, q))
+		goto out;
+
+	return 0;
+out:
+	axienet_dma_bd_release(ndev);
+	return -ENOMEM;
+}
+
+/**
+ * map_dma_q_irq - Map dma q based on interrupt number.
+ * @irq:	irq number
+ * @lp:		axienet local structure
+ *
+ * Return: DMA queue.
+ *
+ * This returns the DMA number on which interrupt has occurred.
+ */
+static int map_dma_q_irq(int irq, struct axienet_local *lp)
+{
+	int i;
+
+	for_each_rx_dma_queue(lp, i) {
+		if (irq == lp->dq[i]->tx_irq || irq == lp->dq[i]->rx_irq)
+			return i;
+	}
+	pr_err("Error mapping DMA irq\n");
+	return -ENODEV;
+}
+
+/**
+ * axienet_tx_irq - Tx Done Isr.
+ * @irq:	irq number
+ * @_ndev:	net_device pointer
+ *
+ * Return: IRQ_HANDLED if device generated a TX interrupt, IRQ_NONE otherwise.
+ *
+ * This is the Axi DMA Tx done Isr. It invokes "axienet_start_xmit_done"
+ * to complete the BD processing.
+ */
+irqreturn_t __maybe_unused axienet_tx_irq(int irq, void *_ndev)
+{
+	u32 cr;
+	unsigned int status;
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i = map_dma_q_irq(irq, lp);
+	struct axienet_dma_q *q;
+
+	if (i < 0)
+		return IRQ_NONE;
+
+	q = lp->dq[i];
+
+	status = axienet_dma_in32(q, XAXIDMA_TX_SR_OFFSET);
+	if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+		axienet_dma_out32(q, XAXIDMA_TX_SR_OFFSET, status);
+		axienet_start_xmit_done(lp->ndev, q);
+		goto out;
+	}
+
+	if (!(status & XAXIDMA_IRQ_ALL_MASK))
+		return IRQ_NONE;
+
+	if (status & XAXIDMA_IRQ_ERROR_MASK) {
+		dev_err(&ndev->dev, "DMA Tx error 0x%x\n", status);
+		dev_err(&ndev->dev, "Current BD is at: %pa\n",
+			&q->tx_bd_v[q->tx_bd_ci].phys);
+
+		cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XAXIDMA_IRQ_ALL_MASK);
+		/* Write to the Tx channel control register */
+		axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, cr);
+
+		cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XAXIDMA_IRQ_ALL_MASK);
+		/* Write to the Rx channel control register */
+		axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+
+		tasklet_schedule(&lp->dma_err_tasklet[i]);
+		axienet_dma_out32(q, XAXIDMA_TX_SR_OFFSET, status);
+	}
+out:
+	return IRQ_HANDLED;
+}
+
+/**
+ * axienet_rx_irq - Rx Isr.
+ * @irq:	irq number
+ * @_ndev:	net_device pointer
+ *
+ * Return: IRQ_HANDLED if device generated a RX interrupt, IRQ_NONE otherwise.
+ *
+ * This is the Axi DMA Rx Isr. It invokes "axienet_recv" to complete the BD
+ * processing.
+ */
+irqreturn_t __maybe_unused axienet_rx_irq(int irq, void *_ndev)
+{
+	u32 cr;
+	unsigned int status;
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i = map_dma_q_irq(irq, lp);
+	struct axienet_dma_q *q;
+
+	if (i < 0)
+		return IRQ_NONE;
+
+	q = lp->dq[i];
+
+	status = axienet_dma_in32(q, XAXIDMA_RX_SR_OFFSET);
+	if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+		cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		cr &= ~(XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK);
+		axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+		napi_schedule(&lp->napi[i]);
+	}
+
+	if (!(status & XAXIDMA_IRQ_ALL_MASK))
+		return IRQ_NONE;
+
+	if (status & XAXIDMA_IRQ_ERROR_MASK) {
+		dev_err(&ndev->dev, "DMA Rx error 0x%x\n", status);
+		dev_err(&ndev->dev, "Current BD is at: %pa\n",
+			&q->rx_bd_v[q->rx_bd_ci].phys);
+
+		cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XAXIDMA_IRQ_ALL_MASK);
+		/* Finally write to the Tx channel control register */
+		axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, cr);
+
+		cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XAXIDMA_IRQ_ALL_MASK);
+			/* write to the Rx channel control register */
+		axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+
+		tasklet_schedule(&lp->dma_err_tasklet[i]);
+		axienet_dma_out32(q, XAXIDMA_RX_SR_OFFSET, status);
+	}
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * axienet_dma_err_handler - Tasklet handler for Axi DMA Error
+ * @data:	Data passed
+ *
+ * Resets the Axi DMA and Axi Ethernet devices, and reconfigures the
+ * Tx/Rx BDs.
+ */
+void __maybe_unused axienet_dma_err_handler(unsigned long data)
+{
+	u32 axienet_status;
+	u32 cr, i;
+	struct axienet_dma_q *q = (struct axienet_dma_q *)data;
+	struct axienet_local *lp = q->lp;
+	struct net_device *ndev = lp->ndev;
+	struct axidma_bd *cur_p;
+
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+
+	__axienet_device_reset(q);
+
+	for (i = 0; i < lp->tx_bd_num; i++) {
+		cur_p = &q->tx_bd_v[i];
+		if (cur_p->phys)
+			dma_unmap_single(ndev->dev.parent, cur_p->phys,
+					 (cur_p->cntrl &
+					  XAXIDMA_BD_CTRL_LENGTH_MASK),
+					 DMA_TO_DEVICE);
+		if (cur_p->tx_skb)
+			dev_kfree_skb_irq((struct sk_buff *)cur_p->tx_skb);
+		cur_p->phys = 0;
+		cur_p->cntrl = 0;
+		cur_p->status = 0;
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app3 = 0;
+		cur_p->app4 = 0;
+		cur_p->sw_id_offset = 0;
+		cur_p->tx_skb = 0;
+	}
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		cur_p = &q->rx_bd_v[i];
+		cur_p->status = 0;
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app3 = 0;
+		cur_p->app4 = 0;
+	}
+
+	q->tx_bd_ci = 0;
+	q->tx_bd_tail = 0;
+	q->rx_bd_ci = 0;
+
+	/* Start updating the Rx channel control register */
+	cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+	/* Update the interrupt coalesce count */
+	cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
+	      (XAXIDMA_DFT_RX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = ((cr & ~XAXIDMA_DELAY_MASK) |
+	      (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XAXIDMA_IRQ_ALL_MASK;
+	/* Finally write to the Rx channel control register */
+	axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+
+	/* Start updating the Tx channel control register */
+	cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+	/* Update the interrupt coalesce count */
+	cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
+	      (XAXIDMA_DFT_TX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
+	      (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XAXIDMA_IRQ_ALL_MASK;
+	/* Finally write to the Tx channel control register */
+	axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, cr);
+
+	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
+	 * halted state. This will make the Rx side ready for reception.
+	 */
+	axienet_dma_bdout(q, XAXIDMA_RX_CDESC_OFFSET, q->rx_bd_p);
+	cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+	axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET,
+			  cr | XAXIDMA_CR_RUNSTOP_MASK);
+	axienet_dma_bdout(q, XAXIDMA_RX_TDESC_OFFSET, q->rx_bd_p +
+			  (sizeof(*q->rx_bd_v) * (lp->rx_bd_num - 1)));
+
+	/* Write to the RS (Run-stop) bit in the Tx channel control register.
+	 * Tx channel is now ready to run. But only after we write to the
+	 * tail pointer register that the Tx channel will start transmitting
+	 */
+	axienet_dma_bdout(q, XAXIDMA_TX_CDESC_OFFSET, q->tx_bd_p);
+	cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+	axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET,
+			  cr | XAXIDMA_CR_RUNSTOP_MASK);
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G) {
+		axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+		axienet_status &= ~XAE_RCW1_RX_MASK;
+		axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
+	}
+
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf) {
+		axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+		if (axienet_status & XAE_INT_RXRJECT_MASK)
+			axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G)
+		axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+
+	lp->axienet_config->setoptions(ndev, lp->options &
+			   ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+	axienet_set_mac_address(ndev, NULL);
+	axienet_set_multicast_list(ndev);
+	lp->axienet_config->setoptions(ndev, lp->options);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -23,6 +23,7 @@
  */
 
 #include <linux/clk.h>
+#include <linux/circ_buf.h>
 #include <linux/delay.h>
 #include <linux/etherdevice.h>
 #include <linux/module.h>
@@ -37,12 +38,20 @@
 #include <linux/phy.h>
 #include <linux/mii.h>
 #include <linux/ethtool.h>
+#include <linux/iopoll.h>
+#include <linux/ptp_classify.h>
+#include <linux/net_tstamp.h>
+#include <linux/random.h>
+#include <net/sock.h>
+#include <linux/xilinx_phy.h>
+#include <linux/clk.h>
 
 #include "xilinx_axienet.h"
 
 /* Descriptors defines for Tx and Rx DMA */
+#define TX_BD_NUM_MIN			(MAX_SKB_FRAGS + 1)
 #define TX_BD_NUM_DEFAULT		64
-#define RX_BD_NUM_DEFAULT		1024
+#define RX_BD_NUM_DEFAULT		128
 #define TX_BD_NUM_MAX			4096
 #define RX_BD_NUM_MAX			4096
 
@@ -52,16 +61,35 @@
 #define DRIVER_VERSION		"1.00a"
 
 #define AXIENET_REGS_N		40
+#define AXIENET_TS_HEADER_LEN	8
+#define XXVENET_TS_HEADER_LEN	4
+#define MRMAC_TS_HEADER_LEN		16
+#define MRMAC_TS_HEADER_WORDS   (MRMAC_TS_HEADER_LEN / 4)
+#define NS_PER_SEC              1000000000ULL /* Nanoseconds per second */
+
+#define MRMAC_RESET_DELAY	1 /* Delay in msecs*/
+
+/* IEEE1588 Message Type field values  */
+#define PTP_TYPE_SYNC		0
+#define PTP_TYPE_PDELAY_REQ	2
+#define PTP_TYPE_PDELAY_RESP	3
+#define PTP_TYPE_OFFSET		42
+/* SW flags used to convey message type for command FIFO handling */
+#define MSG_TYPE_SHIFT			4
+#define MSG_TYPE_SYNC_FLAG		((PTP_TYPE_SYNC + 1) << MSG_TYPE_SHIFT)
+#define MSG_TYPE_PDELAY_RESP_FLAG	((PTP_TYPE_PDELAY_RESP + 1) << \
+									 MSG_TYPE_SHIFT)
+void __iomem *mrmac_gt_pll;
+EXPORT_SYMBOL(mrmac_gt_pll);
 
-/* Match table for of_platform binding */
-static const struct of_device_id axienet_of_match[] = {
-	{ .compatible = "xlnx,axi-ethernet-1.00.a", },
-	{ .compatible = "xlnx,axi-ethernet-1.01.a", },
-	{ .compatible = "xlnx,axi-ethernet-2.01.a", },
-	{},
-};
+void __iomem *mrmac_gt_ctrl;
+EXPORT_SYMBOL(mrmac_gt_ctrl);
 
-MODULE_DEVICE_TABLE(of, axienet_of_match);
+int mrmac_pll_reg;
+EXPORT_SYMBOL(mrmac_pll_reg);
+
+int mrmac_pll_rst;
+EXPORT_SYMBOL(mrmac_pll_rst);
 
 /* Option table for setting up Axi Ethernet hardware options */
 static struct axienet_option axienet_options[] = {
@@ -118,62 +146,62 @@
 	{}
 };
 
-/**
- * axienet_dma_in32 - Memory mapped Axi DMA register read
- * @lp:		Pointer to axienet local structure
- * @reg:	Address offset from the base address of the Axi DMA core
- *
- * Return: The contents of the Axi DMA register
- *
- * This function returns the contents of the corresponding Axi DMA register.
- */
-static inline u32 axienet_dma_in32(struct axienet_local *lp, off_t reg)
-{
-	return ioread32(lp->dma_regs + reg);
-}
-
-/**
- * axienet_dma_out32 - Memory mapped Axi DMA register write.
- * @lp:		Pointer to axienet local structure
- * @reg:	Address offset from the base address of the Axi DMA core
- * @value:	Value to be written into the Axi DMA register
- *
- * This function writes the desired value into the corresponding Axi DMA
- * register.
- */
-static inline void axienet_dma_out32(struct axienet_local *lp,
-				     off_t reg, u32 value)
-{
-	iowrite32(value, lp->dma_regs + reg);
-}
-
-static void axienet_dma_out_addr(struct axienet_local *lp, off_t reg,
-				 dma_addr_t addr)
-{
-	axienet_dma_out32(lp, reg, lower_32_bits(addr));
-
-	if (lp->features & XAE_FEATURE_DMA_64BIT)
-		axienet_dma_out32(lp, reg + 4, upper_32_bits(addr));
-}
-
-static void desc_set_phys_addr(struct axienet_local *lp, dma_addr_t addr,
-			       struct axidma_bd *desc)
-{
-	desc->phys = lower_32_bits(addr);
-	if (lp->features & XAE_FEATURE_DMA_64BIT)
-		desc->phys_msb = upper_32_bits(addr);
-}
+/* Option table for setting up Axi Ethernet hardware options */
+static struct xxvenet_option xxvenet_options[] = {
+	{ /* Turn on FCS stripping on receive packets */
+		.opt = XAE_OPTION_FCS_STRIP,
+		.reg = XXV_RCW1_OFFSET,
+		.m_or = XXV_RCW1_FCS_MASK,
+	}, { /* Turn on FCS insertion on transmit packets */
+		.opt = XAE_OPTION_FCS_INSERT,
+		.reg = XXV_TC_OFFSET,
+		.m_or = XXV_TC_FCS_MASK,
+	}, { /* Enable transmitter */
+		.opt = XAE_OPTION_TXEN,
+		.reg = XXV_TC_OFFSET,
+		.m_or = XXV_TC_TX_MASK,
+	}, { /* Enable receiver */
+		.opt = XAE_OPTION_RXEN,
+		.reg = XXV_RCW1_OFFSET,
+		.m_or = XXV_RCW1_RX_MASK,
+	},
+	{}
+};
 
-static dma_addr_t desc_get_phys_addr(struct axienet_local *lp,
-				     struct axidma_bd *desc)
-{
-	dma_addr_t ret = desc->phys;
+/* Option table for setting up MRMAC hardware options */
+static struct xxvenet_option mrmacenet_options[] = {
+	{ /* Turn on FCS stripping on receive packets */
+		.opt = XAE_OPTION_FCS_STRIP,
+		.reg = MRMAC_CONFIG_RX_OFFSET,
+		.m_or = MRMAC_RX_DEL_FCS_MASK,
+	}, { /* Turn on FCS insertion on transmit packets */
+		.opt = XAE_OPTION_FCS_INSERT,
+		.reg = MRMAC_CONFIG_TX_OFFSET,
+		.m_or = MRMAC_TX_INS_FCS_MASK,
+	}, { /* Enable transmitter */
+		.opt = XAE_OPTION_TXEN,
+		.reg = MRMAC_CONFIG_TX_OFFSET,
+		.m_or = MRMAC_TX_EN_MASK,
+	}, { /* Enable receiver */
+		.opt = XAE_OPTION_RXEN,
+		.reg = MRMAC_CONFIG_RX_OFFSET,
+		.m_or = MRMAC_RX_EN_MASK,
+	},
+	{}
+};
 
-	if (lp->features & XAE_FEATURE_DMA_64BIT)
-		ret |= ((dma_addr_t)desc->phys_msb << 16) << 16;
+struct axienet_ethtools_stat {
+	const char *name;
+};
 
-	return ret;
-}
+static struct axienet_ethtools_stat axienet_get_ethtools_strings_stats[] = {
+	{ "tx_packets" },
+	{ "rx_packets" },
+	{ "tx_bytes" },
+	{ "rx_bytes" },
+	{ "tx_errors" },
+	{ "rx_errors" },
+};
 
 /**
  * axienet_dma_bd_release - Release buffer descriptor rings
@@ -183,53 +211,30 @@
  * axienet_dma_bd_init. axienet_dma_bd_release is called when Axi Ethernet
  * driver stop api is called.
  */
-static void axienet_dma_bd_release(struct net_device *ndev)
+void axienet_dma_bd_release(struct net_device *ndev)
 {
 	int i;
 	struct axienet_local *lp = netdev_priv(ndev);
 
-	/* If we end up here, tx_bd_v must have been DMA allocated. */
-	dma_free_coherent(ndev->dev.parent,
-			  sizeof(*lp->tx_bd_v) * lp->tx_bd_num,
-			  lp->tx_bd_v,
-			  lp->tx_bd_p);
-
-	if (!lp->rx_bd_v)
-		return;
-
-	for (i = 0; i < lp->rx_bd_num; i++) {
-		dma_addr_t phys;
-
-		/* A NULL skb means this descriptor has not been initialised
-		 * at all.
-		 */
-		if (!lp->rx_bd_v[i].skb)
-			break;
-
-		dev_kfree_skb(lp->rx_bd_v[i].skb);
-
-		/* For each descriptor, we programmed cntrl with the (non-zero)
-		 * descriptor size, after it had been successfully allocated.
-		 * So a non-zero value in there means we need to unmap it.
-		 */
-		if (lp->rx_bd_v[i].cntrl) {
-			phys = desc_get_phys_addr(lp, &lp->rx_bd_v[i]);
-			dma_unmap_single(ndev->dev.parent, phys,
-					 lp->max_frm_size, DMA_FROM_DEVICE);
-		}
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	for_each_tx_dma_queue(lp, i) {
+		axienet_mcdma_tx_bd_free(ndev, lp->dq[i]);
+	}
+#endif
+	for_each_rx_dma_queue(lp, i) {
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		axienet_mcdma_rx_bd_free(ndev, lp->dq[i]);
+#else
+		axienet_bd_free(ndev, lp->dq[i]);
+#endif
 	}
-
-	dma_free_coherent(ndev->dev.parent,
-			  sizeof(*lp->rx_bd_v) * lp->rx_bd_num,
-			  lp->rx_bd_v,
-			  lp->rx_bd_p);
 }
 
 /**
  * axienet_dma_bd_init - Setup buffer descriptor rings for Axi DMA
  * @ndev:	Pointer to the net_device structure
  *
- * Return: 0, on success -ENOMEM, on failure
+ * Return: 0, on success -ENOMEM, on failure -EINVAL, on default return
  *
  * This function is called to initialize the Rx and Tx DMA descriptor
  * rings. This initializes the descriptors with required default values
@@ -237,113 +242,29 @@
  */
 static int axienet_dma_bd_init(struct net_device *ndev)
 {
-	u32 cr;
-	int i;
-	struct sk_buff *skb;
+	int i, ret = -EINVAL;
 	struct axienet_local *lp = netdev_priv(ndev);
 
-	/* Reset the indexes which are used for accessing the BDs */
-	lp->tx_bd_ci = 0;
-	lp->tx_bd_tail = 0;
-	lp->rx_bd_ci = 0;
-
-	/* Allocate the Tx and Rx buffer descriptors. */
-	lp->tx_bd_v = dma_alloc_coherent(ndev->dev.parent,
-					 sizeof(*lp->tx_bd_v) * lp->tx_bd_num,
-					 &lp->tx_bd_p, GFP_KERNEL);
-	if (!lp->tx_bd_v)
-		return -ENOMEM;
-
-	lp->rx_bd_v = dma_alloc_coherent(ndev->dev.parent,
-					 sizeof(*lp->rx_bd_v) * lp->rx_bd_num,
-					 &lp->rx_bd_p, GFP_KERNEL);
-	if (!lp->rx_bd_v)
-		goto out;
-
-	for (i = 0; i < lp->tx_bd_num; i++) {
-		dma_addr_t addr = lp->tx_bd_p +
-				  sizeof(*lp->tx_bd_v) *
-				  ((i + 1) % lp->tx_bd_num);
-
-		lp->tx_bd_v[i].next = lower_32_bits(addr);
-		if (lp->features & XAE_FEATURE_DMA_64BIT)
-			lp->tx_bd_v[i].next_msb = upper_32_bits(addr);
-	}
-
-	for (i = 0; i < lp->rx_bd_num; i++) {
-		dma_addr_t addr;
-
-		addr = lp->rx_bd_p + sizeof(*lp->rx_bd_v) *
-			((i + 1) % lp->rx_bd_num);
-		lp->rx_bd_v[i].next = lower_32_bits(addr);
-		if (lp->features & XAE_FEATURE_DMA_64BIT)
-			lp->rx_bd_v[i].next_msb = upper_32_bits(addr);
-
-		skb = netdev_alloc_skb_ip_align(ndev, lp->max_frm_size);
-		if (!skb)
-			goto out;
-
-		lp->rx_bd_v[i].skb = skb;
-		addr = dma_map_single(ndev->dev.parent, skb->data,
-				      lp->max_frm_size, DMA_FROM_DEVICE);
-		if (dma_mapping_error(ndev->dev.parent, addr)) {
-			netdev_err(ndev, "DMA mapping error\n");
-			goto out;
-		}
-		desc_set_phys_addr(lp, addr, &lp->rx_bd_v[i]);
-
-		lp->rx_bd_v[i].cntrl = lp->max_frm_size;
-	}
-
-	/* Start updating the Rx channel control register */
-	cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	/* Update the interrupt coalesce count */
-	cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
-	      ((lp->coalesce_count_rx) << XAXIDMA_COALESCE_SHIFT));
-	/* Update the delay timer count */
-	cr = ((cr & ~XAXIDMA_DELAY_MASK) |
-	      (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
-	/* Enable coalesce, delay timer and error interrupts */
-	cr |= XAXIDMA_IRQ_ALL_MASK;
-	/* Write to the Rx channel control register */
-	axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
-
-	/* Start updating the Tx channel control register */
-	cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	/* Update the interrupt coalesce count */
-	cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
-	      ((lp->coalesce_count_tx) << XAXIDMA_COALESCE_SHIFT));
-	/* Update the delay timer count */
-	cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
-	      (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
-	/* Enable coalesce, delay timer and error interrupts */
-	cr |= XAXIDMA_IRQ_ALL_MASK;
-	/* Write to the Tx channel control register */
-	axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
-
-	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
-	 * halted state. This will make the Rx side ready for reception.
-	 */
-	axienet_dma_out_addr(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
-	cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
-			  cr | XAXIDMA_CR_RUNSTOP_MASK);
-	axienet_dma_out_addr(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
-			     (sizeof(*lp->rx_bd_v) * (lp->rx_bd_num - 1)));
-
-	/* Write to the RS (Run-stop) bit in the Tx channel control register.
-	 * Tx channel is now ready to run. But only after we write to the
-	 * tail pointer register that the Tx channel will start transmitting.
-	 */
-	axienet_dma_out_addr(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
-	cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
-			  cr | XAXIDMA_CR_RUNSTOP_MASK);
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	for_each_tx_dma_queue(lp, i) {
+		ret = axienet_mcdma_tx_q_init(ndev, lp->dq[i]);
+		if (ret != 0)
+			break;
+	}
+#endif
+	for_each_rx_dma_queue(lp, i) {
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		ret = axienet_mcdma_rx_q_init(ndev, lp->dq[i]);
+#else
+		ret = axienet_dma_q_init(ndev, lp->dq[i]);
+#endif
+		if (ret != 0) {
+			netdev_err(ndev, "%s: Failed to init DMA buf %d\n", __func__, ret);
+			break;
+		}
+	}
 
-	return 0;
-out:
-	axienet_dma_bd_release(ndev);
-	return -ENOMEM;
+	return ret;
 }
 
 /**
@@ -354,16 +275,20 @@
  * This function is called to initialize the MAC address of the Axi Ethernet
  * core. It writes to the UAW0 and UAW1 registers of the core.
  */
-static void axienet_set_mac_address(struct net_device *ndev,
-				    const void *address)
+void axienet_set_mac_address(struct net_device *ndev,
+			     const void *address)
 {
 	struct axienet_local *lp = netdev_priv(ndev);
 
 	if (address)
-		memcpy(ndev->dev_addr, address, ETH_ALEN);
+		ether_addr_copy(ndev->dev_addr, address);
 	if (!is_valid_ether_addr(ndev->dev_addr))
 		eth_hw_addr_random(ndev);
 
+	if (lp->axienet_config->mactype != XAXIENET_1G &&
+	    lp->axienet_config->mactype != XAXIENET_2_5G)
+		return;
+
 	/* Set up unicast MAC address filter set its mac address */
 	axienet_iow(lp, XAE_UAW0_OFFSET,
 		    (ndev->dev_addr[0]) |
@@ -391,6 +316,7 @@
 static int netdev_set_mac_address(struct net_device *ndev, void *p)
 {
 	struct sockaddr *addr = p;
+
 	axienet_set_mac_address(ndev, addr->sa_data);
 	return 0;
 }
@@ -406,12 +332,15 @@
  * means whenever the multicast table entries need to be updated this
  * function gets called.
  */
-static void axienet_set_multicast_list(struct net_device *ndev)
+void axienet_set_multicast_list(struct net_device *ndev)
 {
-	int i;
+	int i = 0;
 	u32 reg, af0reg, af1reg;
 	struct axienet_local *lp = netdev_priv(ndev);
 
+	if (lp->axienet_config->mactype != XAXIENET_1G || lp->eth_hasnobuf)
+		return;
+
 	if (ndev->flags & (IFF_ALLMULTI | IFF_PROMISC) ||
 	    netdev_mc_count(ndev) > XAE_MULTICAST_CAM_TABLE_NUM) {
 		/* We must make the kernel realize we had to move into
@@ -426,7 +355,10 @@
 	} else if (!netdev_mc_empty(ndev)) {
 		struct netdev_hw_addr *ha;
 
-		i = 0;
+		reg = axienet_ior(lp, XAE_FMI_OFFSET);
+		reg &= ~XAE_FMI_PM_MASK;
+		axienet_iow(lp, XAE_FMI_OFFSET, reg);
+
 		netdev_for_each_mc_addr(ha, ndev) {
 			if (i >= XAE_MULTICAST_CAM_TABLE_NUM)
 				break;
@@ -445,6 +377,7 @@
 			axienet_iow(lp, XAE_FMI_OFFSET, reg);
 			axienet_iow(lp, XAE_AF0_OFFSET, af0reg);
 			axienet_iow(lp, XAE_AF1_OFFSET, af1reg);
+			axienet_iow(lp, XAE_FFE_OFFSET, 1);
 			i++;
 		}
 	} else {
@@ -452,18 +385,15 @@
 		reg &= ~XAE_FMI_PM_MASK;
 
 		axienet_iow(lp, XAE_FMI_OFFSET, reg);
-
-		for (i = 0; i < XAE_MULTICAST_CAM_TABLE_NUM; i++) {
-			reg = axienet_ior(lp, XAE_FMI_OFFSET) & 0xFFFFFF00;
-			reg |= i;
-
-			axienet_iow(lp, XAE_FMI_OFFSET, reg);
-			axienet_iow(lp, XAE_AF0_OFFSET, 0);
-			axienet_iow(lp, XAE_AF1_OFFSET, 0);
-		}
-
 		dev_info(&ndev->dev, "Promiscuous mode disabled.\n");
 	}
+
+	for (; i < XAE_MULTICAST_CAM_TABLE_NUM; i++) {
+		reg = axienet_ior(lp, XAE_FMI_OFFSET) & 0xFFFFFF00;
+		reg |= i;
+		axienet_iow(lp, XAE_FMI_OFFSET, reg);
+		axienet_iow(lp, XAE_FFE_OFFSET, 0);
+	}
 }
 
 /**
@@ -477,7 +407,7 @@
  * these options in the Axi Ethernet hardware. This is done through
  * axienet_option structure .
  */
-static void axienet_setoptions(struct net_device *ndev, u32 options)
+void axienet_setoptions(struct net_device *ndev, u32 options)
 {
 	int reg;
 	struct axienet_local *lp = netdev_priv(ndev);
@@ -494,10 +424,115 @@
 	lp->options |= options;
 }
 
-static int __axienet_device_reset(struct axienet_local *lp)
+static void xxvenet_setoptions(struct net_device *ndev, u32 options)
 {
-	u32 timeout;
+	int reg;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct xxvenet_option *tp;
+
+	if (lp->axienet_config->mactype == XAXIENET_MRMAC)
+		tp = &mrmacenet_options[0];
+	else
+		tp = &xxvenet_options[0];
+
+	while (tp->opt) {
+		reg = ((axienet_ior(lp, tp->reg)) & ~(tp->m_or));
+		if (options & tp->opt)
+			reg |= tp->m_or;
+		axienet_iow(lp, tp->reg, reg);
+		tp++;
+	}
+
+	lp->options |= options;
+}
+
+static inline void axienet_mrmac_reset(struct axienet_local *lp)
+{
+	u32 val, reg;
+
+	val = axienet_ior(lp, MRMAC_RESET_OFFSET);
+	val |= (MRMAC_RX_SERDES_RST_MASK | MRMAC_TX_SERDES_RST_MASK |
+		MRMAC_RX_RST_MASK | MRMAC_TX_RST_MASK);
+	axienet_iow(lp, MRMAC_RESET_OFFSET, val);
+	mdelay(MRMAC_RESET_DELAY);
+
+	reg = axienet_ior(lp, MRMAC_MODE_OFFSET);
+	if (lp->mrmac_rate == SPEED_25000) {
+		reg &= ~MRMAC_CTL_RATE_CFG_MASK;
+		reg |= MRMAC_CTL_DATA_RATE_25G;
+		reg |= (MRMAC_CTL_AXIS_CFG_25G_IND << MRMAC_CTL_AXIS_CFG_SHIFT);
+		reg |= (MRMAC_CTL_SERDES_WIDTH_25G <<
+			MRMAC_CTL_SERDES_WIDTH_SHIFT);
+	} else {
+		reg &= ~MRMAC_CTL_RATE_CFG_MASK;
+		reg |= MRMAC_CTL_DATA_RATE_10G;
+		reg |= (MRMAC_CTL_AXIS_CFG_10G_IND << MRMAC_CTL_AXIS_CFG_SHIFT);
+		reg |= (MRMAC_CTL_SERDES_WIDTH_10G <<
+			MRMAC_CTL_SERDES_WIDTH_SHIFT);
+	}
+
+	/* For tick reg */
+	reg |= MRMAC_CTL_PM_TICK_MASK;
+	axienet_iow(lp, MRMAC_MODE_OFFSET, reg);
+
+	val = axienet_ior(lp, MRMAC_RESET_OFFSET);
+	val &= ~(MRMAC_RX_SERDES_RST_MASK | MRMAC_TX_SERDES_RST_MASK |
+		MRMAC_RX_RST_MASK | MRMAC_TX_RST_MASK);
+	axienet_iow(lp, MRMAC_RESET_OFFSET, val);
+}
+
+static inline int axienet_mrmac_gt_reset(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 err, val;
+	int i;
+
+	if (mrmac_pll_rst == 0) {
+		/* PLL reset for all lanes */
+
+		for (i = 0; i < MRMAC_MAX_GT_LANES; i++) {
+			iowrite32(MRMAC_GT_RST_ALL_MASK, (lp->gt_ctrl +
+				  (MRMAC_GT_LANE_OFFSET * i) +
+				  MRMAC_GT_CTRL_OFFSET));
+			mdelay(MRMAC_RESET_DELAY);
+			iowrite32(0, (lp->gt_ctrl + (MRMAC_GT_LANE_OFFSET * i) +
+				      MRMAC_GT_CTRL_OFFSET));
+		}
+
+		/* Wait for PLL lock with timeout */
+		err = readl_poll_timeout(lp->gt_pll + MRMAC_GT_PLL_STS_OFFSET,
+					 val, (val & MRMAC_GT_PLL_DONE_MASK),
+					 10, DELAY_OF_ONE_MILLISEC);
+		if (err) {
+			netdev_err(ndev, "MRMAC PLL lock not complete! Cross-check the MAC ref clock configuration\n");
+			return -ENODEV;
+		}
+		mrmac_pll_rst = 1;
+	}
+
+	if (lp->mrmac_rate == SPEED_25000)
+		iowrite32(MRMAC_GT_25G_MASK, (lp->gt_ctrl +
+			  MRMAC_GT_LANE_OFFSET * lp->gt_lane +
+			  MRMAC_GT_RATE_OFFSET));
+	else
+		iowrite32(MRMAC_GT_10G_MASK, (lp->gt_ctrl +
+			  MRMAC_GT_LANE_OFFSET * lp->gt_lane +
+			  MRMAC_GT_RATE_OFFSET));
+
+	iowrite32(MRMAC_GT_RST_RX_MASK | MRMAC_GT_RST_TX_MASK,
+		  (lp->gt_ctrl + MRMAC_GT_LANE_OFFSET * lp->gt_lane +
+		  MRMAC_GT_CTRL_OFFSET));
+	mdelay(MRMAC_RESET_DELAY);
+	iowrite32(0, (lp->gt_ctrl + MRMAC_GT_LANE_OFFSET * lp->gt_lane +
+		  MRMAC_GT_CTRL_OFFSET));
+	mdelay(MRMAC_RESET_DELAY);
+
+	return 0;
+}
 
+void __axienet_device_reset(struct axienet_dma_q *q)
+{
+	u32 timeout;
 	/* Reset Axi DMA. This would reset Axi Ethernet core as well. The reset
 	 * process of Axi DMA takes a while to complete as all pending
 	 * commands/transfers will be flushed or completed during this
@@ -505,83 +540,174 @@
 	 * Note that even though both TX and RX have their own reset register,
 	 * they both reset the entire DMA core, so only one needs to be used.
 	 */
-	axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, XAXIDMA_CR_RESET_MASK);
+	axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, XAXIDMA_CR_RESET_MASK);
 	timeout = DELAY_OF_ONE_MILLISEC;
-	while (axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET) &
+	while (axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET) &
 				XAXIDMA_CR_RESET_MASK) {
 		udelay(1);
 		if (--timeout == 0) {
-			netdev_err(lp->ndev, "%s: DMA reset timeout!\n",
+			netdev_err(q->lp->ndev, "%s: DMA reset timeout!\n",
 				   __func__);
-			return -ETIMEDOUT;
+			break;
 		}
 	}
-
-	return 0;
 }
 
 /**
  * axienet_device_reset - Reset and initialize the Axi Ethernet hardware.
  * @ndev:	Pointer to the net_device structure
  *
+ * Return: 0 on success, Negative value on errors
+ *
  * This function is called to reset and initialize the Axi Ethernet core. This
  * is typically called during initialization. It does a reset of the Axi DMA
  * Rx/Tx channels and initializes the Axi DMA BDs. Since Axi DMA reset lines
  * areconnected to Axi Ethernet reset lines, this in turn resets the Axi
  * Ethernet core. No separate hardware reset is done for the Axi Ethernet
  * core.
- * Returns 0 on success or a negative error number otherwise.
  */
 static int axienet_device_reset(struct net_device *ndev)
 {
 	u32 axienet_status;
 	struct axienet_local *lp = netdev_priv(ndev);
+	u32 err, val;
+	struct axienet_dma_q *q;
+	u32 i;
 	int ret;
+	u8 maj, minor;
 
-	ret = __axienet_device_reset(lp);
-	if (ret)
-		return ret;
+	if (lp->axienet_config->mactype == XAXIENET_10G_25G) {
+		/* Reset the XXV MAC */
+		val = axienet_ior(lp, XXV_GT_RESET_OFFSET);
+		val |= XXV_GT_RESET_MASK;
+		axienet_iow(lp, XXV_GT_RESET_OFFSET, val);
+		/* Wait for 1ms for GT reset to complete as per spec */
+		mdelay(1);
+		val = axienet_ior(lp, XXV_GT_RESET_OFFSET);
+		val &= ~XXV_GT_RESET_MASK;
+		axienet_iow(lp, XXV_GT_RESET_OFFSET, val);
+	}
+
+	if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		/* Reset MRMAC */
+		axienet_mrmac_reset(lp);
+		ret = axienet_mrmac_gt_reset(ndev);
+		if (ret < 0)
+			return ret;
+	}
+
+		for_each_rx_dma_queue(lp, i) {
+			q = lp->dq[i];
+			__axienet_device_reset(q);
+#ifndef CONFIG_AXIENET_HAS_MCDMA
+			__axienet_device_reset(q);
+#endif
+		}
 
 	lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
-	lp->options |= XAE_OPTION_VLAN;
-	lp->options &= (~XAE_OPTION_JUMBO);
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC) {
+		lp->options |= XAE_OPTION_VLAN;
+		lp->options &= (~XAE_OPTION_JUMBO);
+	}
 
-	if ((ndev->mtu > XAE_MTU) &&
-		(ndev->mtu <= XAE_JUMBO_MTU)) {
+	if (ndev->mtu > XAE_MTU && ndev->mtu <= XAE_JUMBO_MTU) {
 		lp->max_frm_size = ndev->mtu + VLAN_ETH_HLEN +
 					XAE_TRL_SIZE;
-
-		if (lp->max_frm_size <= lp->rxmem)
+		if (lp->max_frm_size <= lp->rxmem &&
+		    (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+		     lp->axienet_config->mactype != XAXIENET_MRMAC))
 			lp->options |= XAE_OPTION_JUMBO;
 	}
 
-	ret = axienet_dma_bd_init(ndev);
-	if (ret) {
-		netdev_err(ndev, "%s: descriptor allocation failed\n",
-			   __func__);
-		return ret;
+		ret = axienet_dma_bd_init(ndev);
+		if (ret < 0) {
+			netdev_err(ndev, "%s: descriptor allocation failed\n",
+				   __func__);
+			return ret;
+		}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC) {
+		axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+		axienet_status &= ~XAE_RCW1_RX_MASK;
+		axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
 	}
 
-	axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
-	axienet_status &= ~XAE_RCW1_RX_MASK;
-	axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
-
-	axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
-	if (axienet_status & XAE_INT_RXRJECT_MASK)
-		axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
-	axienet_iow(lp, XAE_IE_OFFSET, lp->eth_irq > 0 ?
-		    XAE_INT_RECV_ERROR_MASK : 0);
+	if (lp->axienet_config->mactype == XAXIENET_10G_25G) {
+		/* Check for block lock bit got set or not
+		 * This ensures that 10G ethernet IP
+		 * is functioning normally or not.
+		 * IP version 3.2 and above, check GT status
+		 * before reading any register
+		 */
+		maj = lp->xxv_ip_version & XXV_MAJ_MASK;
+		minor = (lp->xxv_ip_version & XXV_MIN_MASK) >> 8;
 
-	axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+		if (maj == 3 ? minor >= 2 : maj > 3) {
+			err = readl_poll_timeout(lp->regs + XXV_STAT_GTWIZ_OFFSET,
+						 val, (val & XXV_GTWIZ_RESET_DONE),
+						 10, DELAY_OF_ONE_MILLISEC);
+			if (err) {
+				netdev_err(ndev, "XXV MAC GT reset not complete! Cross-check the MAC ref clock configuration\n");
+				axienet_dma_bd_release(ndev);
+				return err;
+			}
+		}
+		err = readl_poll_timeout(lp->regs + XXV_STATRX_BLKLCK_OFFSET,
+					 val, (val & XXV_RX_BLKLCK_MASK),
+					 10, DELAY_OF_ONE_MILLISEC);
+		if (err)
+			netdev_err(ndev, "XXV MAC block lock not complete! Cross-check the MAC ref clock configuration\n");
+
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+			axienet_rxts_iow(lp, XAXIFIFO_TXTS_RDFR,
+					 XAXIFIFO_TXTS_RESET_MASK);
+			axienet_rxts_iow(lp, XAXIFIFO_TXTS_SRR,
+					 XAXIFIFO_TXTS_RESET_MASK);
+			axienet_txts_iow(lp, XAXIFIFO_TXTS_RDFR,
+					 XAXIFIFO_TXTS_RESET_MASK);
+			axienet_txts_iow(lp, XAXIFIFO_TXTS_SRR,
+					 XAXIFIFO_TXTS_RESET_MASK);
+#endif
+	}
+
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+	if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		axienet_rxts_iow(lp, XAXIFIFO_TXTS_RDFR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+		axienet_rxts_iow(lp, XAXIFIFO_TXTS_SRR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+		axienet_txts_iow(lp, XAXIFIFO_TXTS_RDFR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+		axienet_txts_iow(lp, XAXIFIFO_TXTS_SRR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+	}
+#endif
+
+	if (lp->axienet_config->mactype == XAXIENET_1G &&
+	    !lp->eth_hasnobuf) {
+		axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+		if (axienet_status & XAE_INT_RXRJECT_MASK)
+			axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+		/* Enable receive erros */
+		axienet_iow(lp, XAE_IE_OFFSET, lp->eth_irq > 0 ?
+			    XAE_INT_RECV_ERROR_MASK : 0);
+	}
+
+	if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+	    lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		lp->options |= XAE_OPTION_FCS_STRIP;
+		lp->options |= XAE_OPTION_FCS_INSERT;
+	} else {
+		axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+	}
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
 
-	/* Sync default options with HW but leave receiver and
-	 * transmitter disabled.
-	 */
-	axienet_setoptions(ndev, lp->options &
-			   ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
 	axienet_set_mac_address(ndev, NULL);
 	axienet_set_multicast_list(ndev);
-	axienet_setoptions(ndev, lp->options);
+	lp->axienet_config->setoptions(ndev, lp->options);
 
 	netif_trans_update(ndev);
 
@@ -589,67 +715,225 @@
 }
 
 /**
- * axienet_free_tx_chain - Clean up a series of linked TX descriptors.
+ * axienet_adjust_link - Adjust the PHY link speed/duplex.
  * @ndev:	Pointer to the net_device structure
- * @first_bd:	Index of first descriptor to clean up
- * @nr_bds:	Number of descriptors to clean up, can be -1 if unknown.
- * @sizep:	Pointer to a u32 filled with the total sum of all bytes
- * 		in all cleaned-up descriptors. Ignored if NULL.
- *
- * Would either be called after a successful transmit operation, or after
- * there was an error when setting up the chain.
- * Returns the number of descriptors handled.
+ *
+ * This function is called to change the speed and duplex setting after
+ * auto negotiation is done by the PHY. This is the function that gets
+ * registered with the PHY interface through the "of_phy_connect" call.
+ */
+void axienet_adjust_link(struct net_device *ndev)
+{
+	u32 emmc_reg;
+	u32 link_state;
+	u32 setspeed = 1;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct phy_device *phy = ndev->phydev;
+
+	link_state = phy->speed | (phy->duplex << 1) | phy->link;
+	if (lp->last_link != link_state) {
+		if (phy->speed == SPEED_10 || phy->speed == SPEED_100) {
+			if (lp->phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+				setspeed = 0;
+		} else {
+			if (phy->speed == SPEED_1000 &&
+			    lp->phy_mode == PHY_INTERFACE_MODE_MII)
+				setspeed = 0;
+		}
+
+		if (setspeed == 1) {
+			emmc_reg = axienet_ior(lp, XAE_EMMC_OFFSET);
+			emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
+
+			switch (phy->speed) {
+			case SPEED_2500:
+				emmc_reg |= XAE_EMMC_LINKSPD_2500;
+				break;
+			case SPEED_1000:
+				emmc_reg |= XAE_EMMC_LINKSPD_1000;
+				break;
+			case SPEED_100:
+				emmc_reg |= XAE_EMMC_LINKSPD_100;
+				break;
+			case SPEED_10:
+				emmc_reg |= XAE_EMMC_LINKSPD_10;
+				break;
+			default:
+				dev_err(&ndev->dev, "Speed other than 10, 100 ");
+				dev_err(&ndev->dev, "or 1Gbps is not supported\n");
+				break;
+			}
+
+			axienet_iow(lp, XAE_EMMC_OFFSET, emmc_reg);
+			phy_print_status(phy);
+		} else {
+			netdev_err(ndev,
+				   "Error setting Axi Ethernet mac speed\n");
+		}
+
+		lp->last_link = link_state;
+	}
+}
+
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+/**
+ * axienet_tx_hwtstamp - Read tx timestamp from hw and update it to the skbuff
+ * @lp:		Pointer to axienet local structure
+ * @cur_p:	Pointer to the axi_dma/axi_mcdma current bd
+ *
+ * Return:	None.
  */
-static int axienet_free_tx_chain(struct net_device *ndev, u32 first_bd,
-				 int nr_bds, u32 *sizep)
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+void axienet_tx_hwtstamp(struct axienet_local *lp,
+			 struct aximcdma_bd *cur_p)
+#else
+void axienet_tx_hwtstamp(struct axienet_local *lp,
+			 struct axidma_bd *cur_p)
+#endif
 {
-	struct axienet_local *lp = netdev_priv(ndev);
-	struct axidma_bd *cur_p;
-	int max_bds = nr_bds;
-	unsigned int status;
-	dma_addr_t phys;
-	int i;
+	u32 sec = 0, nsec = 0, val;
+	u64 time64;
+	int err = 0;
+	u32 count, len = lp->axienet_config->tx_ptplen;
+	struct skb_shared_hwtstamps *shhwtstamps =
+		skb_hwtstamps((struct sk_buff *)cur_p->ptp_tx_skb);
+
+	val = axienet_txts_ior(lp, XAXIFIFO_TXTS_ISR);
+	if (unlikely(!(val & XAXIFIFO_TXTS_INT_RC_MASK)))
+		dev_info(lp->dev, "Did't get FIFO tx interrupt %d\n", val);
 
-	if (max_bds == -1)
-		max_bds = lp->tx_bd_num;
+	/* If FIFO is configured in cut through Mode we will get Rx complete
+	 * interrupt even one byte is there in the fifo wait for the full packet
+	 */
+	err = readl_poll_timeout_atomic(lp->tx_ts_regs + XAXIFIFO_TXTS_RLR, val,
+					((val & XAXIFIFO_TXTS_RXFD_MASK) >=
+					len), 0, 1000000);
+	if (err) {
+		netdev_err(lp->ndev, "%s: Didn't get the full timestamp packet",
+			   __func__);
+		goto skb_exit;
+	}
 
-	for (i = 0; i < max_bds; i++) {
-		cur_p = &lp->tx_bd_v[(first_bd + i) % lp->tx_bd_num];
-		status = cur_p->status;
+	nsec = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
+	sec  = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
+	val = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
+	val = ((val & XAXIFIFO_TXTS_TAG_MASK) >> XAXIFIFO_TXTS_TAG_SHIFT);
+	dev_dbg(lp->dev, "tx_stamp:[%04x] %04x %u %9u\n",
+		cur_p->ptp_tx_ts_tag, val, sec, nsec);
+
+	if (val != cur_p->ptp_tx_ts_tag) {
+		count = axienet_txts_ior(lp, XAXIFIFO_TXTS_RFO);
+		while (count) {
+			nsec = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
+			sec  = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
+			val = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
+			val = ((val & XAXIFIFO_TXTS_TAG_MASK) >>
+				XAXIFIFO_TXTS_TAG_SHIFT);
+
+			dev_dbg(lp->dev, "tx_stamp:[%04x] %04x %u %9u\n",
+				cur_p->ptp_tx_ts_tag, val, sec, nsec);
+			if (val == cur_p->ptp_tx_ts_tag)
+				break;
+			count = axienet_txts_ior(lp, XAXIFIFO_TXTS_RFO);
+		}
+		if (val != cur_p->ptp_tx_ts_tag) {
+			dev_info(lp->dev, "Mismatching 2-step tag. Got %x",
+				 val);
+			dev_info(lp->dev, "Expected %x\n",
+				 cur_p->ptp_tx_ts_tag);
+		}
+	}
 
-		/* If no number is given, clean up *all* descriptors that have
-		 * been completed by the MAC.
-		 */
-		if (nr_bds == -1 && !(status & XAXIDMA_BD_STS_COMPLETE_MASK))
-			break;
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		val = axienet_txts_ior(lp, XAXIFIFO_TXTS_RXFD);
 
-		phys = desc_get_phys_addr(lp, cur_p);
-		dma_unmap_single(ndev->dev.parent, phys,
-				 (cur_p->cntrl & XAXIDMA_BD_CTRL_LENGTH_MASK),
-				 DMA_TO_DEVICE);
+skb_exit:
+	time64 = sec * NS_PER_SEC + nsec;
+	memset(shhwtstamps, 0, sizeof(struct skb_shared_hwtstamps));
+	shhwtstamps->hwtstamp = ns_to_ktime(time64);
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		skb_pull((struct sk_buff *)cur_p->ptp_tx_skb,
+			 AXIENET_TS_HEADER_LEN);
 
-		if (cur_p->skb && (status & XAXIDMA_BD_STS_COMPLETE_MASK))
-			dev_consume_skb_irq(cur_p->skb);
+	skb_tstamp_tx((struct sk_buff *)cur_p->ptp_tx_skb, shhwtstamps);
+	dev_kfree_skb_any((struct sk_buff *)cur_p->ptp_tx_skb);
+	cur_p->ptp_tx_skb = 0;
+}
 
-		cur_p->cntrl = 0;
-		cur_p->app0 = 0;
-		cur_p->app1 = 0;
-		cur_p->app2 = 0;
-		cur_p->app4 = 0;
-		cur_p->status = 0;
-		cur_p->skb = NULL;
+static inline bool is_ptp_os_pdelay_req(struct sk_buff *skb,
+					struct axienet_local *lp)
+{
+	u8 *msg_type;
 
-		if (sizep)
-			*sizep += status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+	msg_type = (u8 *)skb->data + PTP_TYPE_OFFSET;
+	return (((*msg_type & 0xF) == PTP_TYPE_PDELAY_REQ) &&
+		(lp->tstamp_config.tx_type == HWTSTAMP_TX_ONESTEP_P2P));
+}
+
+/**
+ * axienet_rx_hwtstamp - Read rx timestamp from hw and update it to the skbuff
+ * @lp:		Pointer to axienet local structure
+ * @skb:	Pointer to the sk_buff structure
+ *
+ * Return:	None.
+ */
+static void axienet_rx_hwtstamp(struct axienet_local *lp,
+				struct sk_buff *skb)
+{
+	u32 sec = 0, nsec = 0, val;
+	u64 time64;
+	int err = 0;
+	struct skb_shared_hwtstamps *shhwtstamps = skb_hwtstamps(skb);
+
+	val = axienet_rxts_ior(lp, XAXIFIFO_TXTS_ISR);
+	if (unlikely(!(val & XAXIFIFO_TXTS_INT_RC_MASK))) {
+		dev_info(lp->dev, "Did't get FIFO rx interrupt %d\n", val);
+		return;
+	}
+
+	val = axienet_rxts_ior(lp, XAXIFIFO_TXTS_RFO);
+	if (!val)
+		return;
+
+	/* If FIFO is configured in cut through Mode we will get Rx complete
+	 * interrupt even one byte is there in the fifo wait for the full packet
+	 */
+	err = readl_poll_timeout_atomic(lp->rx_ts_regs + XAXIFIFO_TXTS_RLR, val,
+					((val & XAXIFIFO_TXTS_RXFD_MASK) >= 12),
+					0, 1000000);
+	if (err) {
+		netdev_err(lp->ndev, "%s: Didn't get the full timestamp packet",
+			   __func__);
+		return;
 	}
 
-	return i;
+	nsec = axienet_rxts_ior(lp, XAXIFIFO_TXTS_RXFD);
+	sec  = axienet_rxts_ior(lp, XAXIFIFO_TXTS_RXFD);
+	val = axienet_rxts_ior(lp, XAXIFIFO_TXTS_RXFD);
+
+	if (is_ptp_os_pdelay_req(skb, lp)) {
+		/* Need to save PDelay resp RX time for HW 1 step
+		 * timestamping on PDelay Response.
+		 */
+		lp->ptp_os_cf = mul_u32_u32(sec, NSEC_PER_SEC);
+		lp->ptp_os_cf += nsec;
+		lp->ptp_os_cf = (lp->ptp_os_cf << 16);
+	}
+
+	if (lp->tstamp_config.rx_filter == HWTSTAMP_FILTER_ALL) {
+		time64 = sec * NS_PER_SEC + nsec;
+		shhwtstamps->hwtstamp = ns_to_ktime(time64);
+	}
 }
+#endif
 
 /**
  * axienet_start_xmit_done - Invoked once a transmit is completed by the
  * Axi DMA Tx channel.
  * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
  *
  * This function is invoked from the Axi DMA Tx isr to notify the completion
  * of transmit operation. It clears fields in the corresponding Tx BDs and
@@ -657,30 +941,91 @@
  * buffer. It finally invokes "netif_wake_queue" to restart transmission if
  * required.
  */
-static void axienet_start_xmit_done(struct net_device *ndev)
+void axienet_start_xmit_done(struct net_device *ndev,
+			     struct axienet_dma_q *q)
 {
-	struct axienet_local *lp = netdev_priv(ndev);
-	u32 packets = 0;
 	u32 size = 0;
+	u32 packets = 0;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	struct aximcdma_bd *cur_p;
+#else
+	struct axidma_bd *cur_p;
+#endif
+	unsigned int status = 0;
 
-	packets = axienet_free_tx_chain(ndev, lp->tx_bd_ci, -1, &size);
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p = &q->txq_bd_v[q->tx_bd_ci];
+	status = cur_p->sband_stats;
+#else
+	cur_p = &q->tx_bd_v[q->tx_bd_ci];
+	status = cur_p->status;
+#endif
+	while (status & XAXIDMA_BD_STS_COMPLETE_MASK) {
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+		if (cur_p->ptp_tx_skb)
+			axienet_tx_hwtstamp(lp, cur_p);
+#endif
+		if (cur_p->tx_desc_mapping == DESC_DMA_MAP_PAGE)
+			dma_unmap_page(ndev->dev.parent, cur_p->phys,
+				       cur_p->cntrl &
+				       XAXIDMA_BD_CTRL_LENGTH_MASK,
+				       DMA_TO_DEVICE);
+		else
+			dma_unmap_single(ndev->dev.parent, cur_p->phys,
+					 cur_p->cntrl &
+					 XAXIDMA_BD_CTRL_LENGTH_MASK,
+					 DMA_TO_DEVICE);
+		if (cur_p->tx_skb)
+			dev_kfree_skb_irq((struct sk_buff *)cur_p->tx_skb);
+		/*cur_p->phys = 0;*/
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app4 = 0;
+		/* ensure our transmit path and device don't prematurely see status cleared */
+		wmb();
+		cur_p->cntrl = 0;
+		cur_p->status = 0;
+		cur_p->tx_skb = 0;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		cur_p->sband_stats = 0;
+#endif
 
-	lp->tx_bd_ci += packets;
-	if (lp->tx_bd_ci >= lp->tx_bd_num)
-		lp->tx_bd_ci -= lp->tx_bd_num;
+		size += status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+		packets++;
+
+		if (++q->tx_bd_ci >= lp->tx_bd_num)
+			q->tx_bd_ci = 0;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		cur_p = &q->txq_bd_v[q->tx_bd_ci];
+		status = cur_p->sband_stats;
+#else
+		cur_p = &q->tx_bd_v[q->tx_bd_ci];
+		status = cur_p->status;
+#endif
+	}
 
 	ndev->stats.tx_packets += packets;
 	ndev->stats.tx_bytes += size;
+	q->tx_packets += packets;
+	q->tx_bytes += size;
 
 	/* Matches barrier in axienet_start_xmit */
 	smp_mb();
 
-	netif_wake_queue(ndev);
+	/* Fixme: With the existing multiqueue implementation
+	 * in the driver it is difficult to get the exact queue info.
+	 * We should wake only the particular queue
+	 * instead of waking all ndev queues.
+	 */
+	netif_tx_wake_all_queues(ndev);
 }
 
 /**
  * axienet_check_tx_bd_space - Checks if a BD/group of BDs are currently busy
- * @lp:		Pointer to the axienet_local structure
+ * @q:		Pointer to DMA queue structure
  * @num_frag:	The number of BDs to check for
  *
  * Return: 0, on success
@@ -691,48 +1036,341 @@
  * transmission. If the BD or any of the BDs are not free the function
  * returns a busy status. This is invoked from axienet_start_xmit.
  */
-static inline int axienet_check_tx_bd_space(struct axienet_local *lp,
+static inline int axienet_check_tx_bd_space(struct axienet_dma_q *q,
 					    int num_frag)
 {
+	struct axienet_local *lp = q->lp;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	struct aximcdma_bd *cur_p;
+
+	if (CIRC_SPACE(q->tx_bd_tail, q->tx_bd_ci, lp->tx_bd_num) < (num_frag + 1))
+		return NETDEV_TX_BUSY;
+
+	cur_p = &q->txq_bd_v[(q->tx_bd_tail + num_frag) % lp->tx_bd_num];
+	if (cur_p->sband_stats & XMCDMA_BD_STS_ALL_MASK)
+		return NETDEV_TX_BUSY;
+#else
 	struct axidma_bd *cur_p;
-	cur_p = &lp->tx_bd_v[(lp->tx_bd_tail + num_frag) % lp->tx_bd_num];
+
+	if (CIRC_SPACE(q->tx_bd_tail, q->tx_bd_ci, lp->tx_bd_num) < (num_frag + 1))
+		return NETDEV_TX_BUSY;
+
+	cur_p = &q->tx_bd_v[(q->tx_bd_tail + num_frag) % lp->tx_bd_num];
 	if (cur_p->status & XAXIDMA_BD_STS_ALL_MASK)
 		return NETDEV_TX_BUSY;
+#endif
 	return 0;
 }
 
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
 /**
- * axienet_start_xmit - Starts the transmission.
- * @skb:	sk_buff pointer that contains data to be Txed.
- * @ndev:	Pointer to net_device structure.
+ * axienet_create_tsheader - Create timestamp header for tx
+ * @q:		Pointer to DMA queue structure
+ * @buf:	Pointer to the buf to copy timestamp header
+ * @msg_type:	PTP message type
  *
- * Return: NETDEV_TX_OK, on success
- *	    NETDEV_TX_BUSY, if any of the descriptors are not free
- *
- * This function is invoked from upper layers to initiate transmission. The
- * function uses the next available free BDs and populates their fields to
- * start the transmission. Additionally if checksum offloading is supported,
- * it populates AXI Stream Control fields with appropriate values.
+ * Return: 0, on success
+ *	    NETDEV_TX_BUSY, if timestamp FIFO has no vacancy
  */
-static netdev_tx_t
-axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+static int axienet_create_tsheader(u8 *buf, u8 msg_type,
+				   struct axienet_dma_q *q)
+{
+	struct axienet_local *lp = q->lp;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	struct aximcdma_bd *cur_p;
+#else
+	struct axidma_bd *cur_p;
+#endif
+	u64 val;
+	u32 tmp[MRMAC_TS_HEADER_WORDS];
+	unsigned long flags;
+	int i;
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p = &q->txq_bd_v[q->tx_bd_tail];
+#else
+	cur_p = &q->tx_bd_v[q->tx_bd_tail];
+#endif
+
+	if ((msg_type & 0xF) == TX_TS_OP_NOOP) {
+		buf[0] = TX_TS_OP_NOOP;
+	} else if ((msg_type & 0xF) == TX_TS_OP_ONESTEP) {
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+			/* For Sync Packet */
+			if ((msg_type & 0xF0) == MSG_TYPE_SYNC_FLAG) {
+				buf[0] = TX_TS_OP_ONESTEP | TX_TS_CSUM_UPDATE_MRMAC;
+				buf[2] = cur_p->ptp_tx_ts_tag & 0xFF;
+				buf[3] = (cur_p->ptp_tx_ts_tag >> 8) & 0xFF;
+				buf[4] = TX_PTP_CF_OFFSET;
+				buf[6] = TX_PTP_CSUM_OFFSET;
+			}
+			/* For PDelay Response packet */
+			if ((msg_type & 0xF0) == MSG_TYPE_PDELAY_RESP_FLAG) {
+				buf[0] = TX_TS_OP_ONESTEP | TX_TS_CSUM_UPDATE_MRMAC |
+					TX_TS_PDELAY_UPDATE_MRMAC;
+				buf[2] = cur_p->ptp_tx_ts_tag & 0xFF;
+				buf[3] = (cur_p->ptp_tx_ts_tag >> 8) & 0xFF;
+				buf[4] = TX_PTP_CF_OFFSET;
+				buf[6] = TX_PTP_CSUM_OFFSET;
+				/* Prev saved TS */
+				memcpy(&buf[8], &lp->ptp_os_cf, 8);
+			}
+		} else {
+			/* Legacy */
+			buf[0] = TX_TS_OP_ONESTEP;
+			buf[1] = TX_TS_CSUM_UPDATE;
+			buf[4] = TX_PTP_TS_OFFSET;
+			buf[6] = TX_PTP_CSUM_OFFSET;
+		}
+	} else {
+		buf[0] = TX_TS_OP_TWOSTEP;
+		buf[2] = cur_p->ptp_tx_ts_tag & 0xFF;
+		buf[3] = (cur_p->ptp_tx_ts_tag >> 8) & 0xFF;
+	}
+
+	if (lp->axienet_config->mactype == XAXIENET_1G ||
+	    lp->axienet_config->mactype == XAXIENET_2_5G) {
+		memcpy(&val, buf, AXIENET_TS_HEADER_LEN);
+		swab64s(&val);
+		memcpy(buf, &val, AXIENET_TS_HEADER_LEN);
+	} else if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+		   lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		memcpy(&tmp[0], buf, lp->axienet_config->ts_header_len);
+		/* Check for Transmit Data FIFO Vacancy */
+		spin_lock_irqsave(&lp->ptp_tx_lock, flags);
+		if (!axienet_txts_ior(lp, XAXIFIFO_TXTS_TDFV)) {
+			spin_unlock_irqrestore(&lp->ptp_tx_lock, flags);
+			return NETDEV_TX_BUSY;
+		}
+
+		for (i = 0; i < lp->axienet_config->ts_header_len / 4; i++)
+			axienet_txts_iow(lp, XAXIFIFO_TXTS_TXFD, tmp[i]);
+
+		axienet_txts_iow(lp, XAXIFIFO_TXTS_TLR, lp->axienet_config->ts_header_len);
+		spin_unlock_irqrestore(&lp->ptp_tx_lock, flags);
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+static inline u8 ptp_os(struct sk_buff *skb, struct axienet_local *lp)
+{
+	u8 *msg_type;
+	int packet_flags = 0;
+
+	/* Identify and return packets requiring PTP one step TS */
+	msg_type = (u8 *)skb->data + PTP_TYPE_OFFSET;
+	if ((*msg_type & 0xF) == PTP_TYPE_SYNC)
+		packet_flags = MSG_TYPE_SYNC_FLAG;
+	else if (((*msg_type & 0xF) == PTP_TYPE_PDELAY_RESP) &&
+		 (lp->tstamp_config.tx_type == HWTSTAMP_TX_ONESTEP_P2P))
+		packet_flags = MSG_TYPE_PDELAY_RESP_FLAG;
+
+	return packet_flags;
+}
+
+static int axienet_skb_tstsmp(struct sk_buff **__skb, struct axienet_dma_q *q,
+			      struct net_device *ndev)
+{
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	struct aximcdma_bd *cur_p;
+#else
+	struct axidma_bd *cur_p;
+	unsigned long flags;
+	u32 pad = 0;
+
+	num_frag = skb_shinfo(skb)->nr_frags;
+	cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
+
+	if (axienet_check_tx_bd_space(lp, num_frag + 1)) {
+		/* Should not happen as last start_xmit call should have
+		 * checked for sufficient space and queue should only be
+		 * woken when sufficient space is available.
+		 */
+		netif_stop_queue(ndev);
+		if (net_ratelimit())
+			netdev_warn(ndev, "TX ring unexpectedly full\n");
+		return NETDEV_TX_BUSY;
+	}
+
+	spin_lock_irqsave(&lp->tx_lock, flags);
+	if (axienet_check_tx_bd_space(lp, num_frag)) {
+		if (netif_queue_stopped(ndev)) {
+			spin_unlock_irqrestore(&lp->tx_lock, flags);
+			return NETDEV_TX_BUSY;
+		}
+
+		netif_stop_queue(ndev);
+
+		/* Matches barrier in axienet_start_xmit_done */
+		smp_mb();
+
+		/* Space might have just been freed - check again */
+		if (axienet_check_tx_bd_space(lp, num_frag)) {
+			spin_unlock_irqrestore(&lp->tx_lock, flags);
+			return NETDEV_TX_BUSY;
+		}
+
+		netif_wake_queue(ndev);
+	}
+#endif
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct sk_buff *old_skb = *__skb;
+	struct sk_buff *skb = *__skb;
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p = &q->txq_bd_v[q->tx_bd_tail];
+#else
+	cur_p = &q->tx_bd_v[q->tx_bd_tail];
+#endif
+
+	if (((lp->tstamp_config.tx_type == HWTSTAMP_TX_ONESTEP_SYNC ||
+	      lp->tstamp_config.tx_type == HWTSTAMP_TX_ON) ||
+	       lp->eth_hasptp) && lp->axienet_config->mactype !=
+	       XAXIENET_10G_25G &&
+	       lp->axienet_config->mactype != XAXIENET_MRMAC) {
+		u8 *tmp;
+		struct sk_buff *new_skb;
+
+		if (skb_headroom(old_skb) < AXIENET_TS_HEADER_LEN) {
+			new_skb =
+			skb_realloc_headroom(old_skb,
+					     AXIENET_TS_HEADER_LEN);
+			if (!new_skb) {
+				dev_err(&ndev->dev, "failed to allocate new socket buffer\n");
+				dev_kfree_skb_any(old_skb);
+				return NETDEV_TX_BUSY;
+			}
+
+			/*  Transfer the ownership to the
+			 *  new socket buffer if required
+			 */
+			if (old_skb->sk)
+				skb_set_owner_w(new_skb, old_skb->sk);
+			dev_kfree_skb_any(old_skb);
+			*__skb = new_skb;
+			skb = new_skb;
+		}
+
+		tmp = skb_push(skb, AXIENET_TS_HEADER_LEN);
+		memset(tmp, 0, AXIENET_TS_HEADER_LEN);
+		cur_p->ptp_tx_ts_tag++;
+
+		if (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) {
+			if (lp->tstamp_config.tx_type ==
+				HWTSTAMP_TX_ONESTEP_SYNC) {
+				axienet_create_tsheader(tmp,
+							TX_TS_OP_ONESTEP
+							, q);
+			} else {
+				axienet_create_tsheader(tmp,
+							TX_TS_OP_TWOSTEP
+							, q);
+				skb_shinfo(skb)->tx_flags |=
+						SKBTX_IN_PROGRESS;
+				cur_p->ptp_tx_skb =
+					(unsigned long)skb_get(skb);
+			}
+		}
+	} else if ((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
+			  (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+			   lp->axienet_config->mactype == XAXIENET_MRMAC)) {
+		cur_p->ptp_tx_ts_tag = prandom_u32_max(XAXIFIFO_TXTS_TAG_MAX) + 1;
+			dev_dbg(lp->dev, "tx_tag:[%04x]\n",
+				cur_p->ptp_tx_ts_tag);
+			if (lp->tstamp_config.tx_type == HWTSTAMP_TX_ONESTEP_SYNC ||
+			    lp->tstamp_config.tx_type == HWTSTAMP_TX_ONESTEP_P2P) {
+				u8 packet_flags = ptp_os(skb, lp);
+
+				/* Pass one step flag with packet type (sync/pdelay resp)
+				 * to command FIFO helper only when one step TS is required.
+				 * Pass the default two step flag for other PTP events.
+				 */
+				if (!packet_flags)
+					packet_flags = TX_TS_OP_TWOSTEP;
+				else
+					packet_flags |= TX_TS_OP_ONESTEP;
+
+				if (axienet_create_tsheader(lp->tx_ptpheader,
+							    packet_flags,
+							    q))
+					return NETDEV_TX_BUSY;
+
+				/* skb TS passing is required for non one step TS packets */
+				if (packet_flags == TX_TS_OP_TWOSTEP) {
+					skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+					cur_p->ptp_tx_skb = (phys_addr_t)skb_get(skb);
+				}
+			} else {
+				if (axienet_create_tsheader(lp->tx_ptpheader,
+							    TX_TS_OP_TWOSTEP,
+							    q))
+					return NETDEV_TX_BUSY;
+				skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+				cur_p->ptp_tx_skb = (phys_addr_t)skb_get(skb);
+			}
+	} else if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+		   lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		dev_dbg(lp->dev, "tx_tag:NOOP\n");
+			if (axienet_create_tsheader(lp->tx_ptpheader,
+						    TX_TS_OP_NOOP, q))
+				return NETDEV_TX_BUSY;
+	}
+
+	return NETDEV_TX_OK;
+}
+#endif
+
+int axienet_queue_xmit(struct sk_buff *skb,
+		       struct net_device *ndev, u16 map)
 {
 	u32 ii;
 	u32 num_frag;
 	u32 csum_start_off;
 	u32 csum_index_off;
-	skb_frag_t *frag;
-	dma_addr_t tail_p, phys;
+	dma_addr_t tail_p;
 	struct axienet_local *lp = netdev_priv(ndev);
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	struct aximcdma_bd *cur_p;
+#else
 	struct axidma_bd *cur_p;
-	u32 orig_tail_ptr = lp->tx_bd_tail;
+#endif
+	unsigned long flags;
+	struct axienet_dma_q *q;
+
+	if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+	    lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		/* Need to manually pad the small frames in case of XXV MAC
+		 * because the pad field is not added by the IP. We must present
+		 * a packet that meets the minimum length to the IP core.
+		 * When the IP core is configured to calculate and add the FCS
+		 * to the packet the minimum packet length is 60 bytes.
+		 */
+		if (eth_skb_pad(skb)) {
+			ndev->stats.tx_dropped++;
+			ndev->stats.tx_errors++;
+			return NETDEV_TX_OK;
+		}
+	}
 
 	num_frag = skb_shinfo(skb)->nr_frags;
-	cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
 
-	if (axienet_check_tx_bd_space(lp, num_frag)) {
-		if (netif_queue_stopped(ndev))
+	q = lp->dq[map];
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p = &q->txq_bd_v[q->tx_bd_tail];
+#else
+	cur_p = &q->tx_bd_v[q->tx_bd_tail];
+#endif
+
+	spin_lock_irqsave(&q->tx_lock, flags);
+	if (axienet_check_tx_bd_space(q, num_frag)) {
+		if (netif_queue_stopped(ndev)) {
+			spin_unlock_irqrestore(&q->tx_lock, flags);
 			return NETDEV_TX_BUSY;
+		}
 
 		netif_stop_queue(ndev);
 
@@ -740,83 +1378,164 @@
 		smp_mb();
 
 		/* Space might have just been freed - check again */
-		if (axienet_check_tx_bd_space(lp, num_frag))
+		if (axienet_check_tx_bd_space(q, num_frag)) {
+			spin_unlock_irqrestore(&q->tx_lock, flags);
 			return NETDEV_TX_BUSY;
+		}
 
 		netif_wake_queue(ndev);
 	}
 
-	if (skb->ip_summed == CHECKSUM_PARTIAL) {
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+	if (axienet_skb_tstsmp(&skb, q, ndev)) {
+		spin_unlock_irqrestore(&q->tx_lock, flags);
+		return NETDEV_TX_BUSY;
+	}
+#endif
+	if (skb->ip_summed == CHECKSUM_PARTIAL && !lp->eth_hasnobuf &&
+	    lp->axienet_config->mactype == XAXIENET_1G) {
 		if (lp->features & XAE_FEATURE_FULL_TX_CSUM) {
 			/* Tx Full Checksum Offload Enabled */
 			cur_p->app0 |= 2;
-		} else if (lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) {
+		} else if (lp->features & XAE_FEATURE_PARTIAL_TX_CSUM) {
 			csum_start_off = skb_transport_offset(skb);
 			csum_index_off = csum_start_off + skb->csum_offset;
 			/* Tx Partial Checksum Offload Enabled */
 			cur_p->app0 |= 1;
 			cur_p->app1 = (csum_start_off << 16) | csum_index_off;
 		}
-	} else if (skb->ip_summed == CHECKSUM_UNNECESSARY) {
+	} else if (skb->ip_summed == CHECKSUM_UNNECESSARY &&
+		   !lp->eth_hasnobuf &&
+		   (lp->axienet_config->mactype == XAXIENET_1G)) {
 		cur_p->app0 |= 2; /* Tx Full Checksum Offload Enabled */
 	}
 
-	phys = dma_map_single(ndev->dev.parent, skb->data,
-			      skb_headlen(skb), DMA_TO_DEVICE);
-	if (unlikely(dma_mapping_error(ndev->dev.parent, phys))) {
-		if (net_ratelimit())
-			netdev_err(ndev, "TX DMA mapping error\n");
-		ndev->stats.tx_dropped++;
-		return NETDEV_TX_OK;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p->cntrl = (skb_headlen(skb) | XMCDMA_BD_CTRL_TXSOF_MASK);
+#else
+	cur_p->cntrl = (skb_headlen(skb) | XAXIDMA_BD_CTRL_TXSOF_MASK);
+#endif
+
+	if (!q->eth_hasdre &&
+	    (((phys_addr_t)skb->data & 0x3) || num_frag > 0)) {
+		skb_copy_and_csum_dev(skb, q->tx_buf[q->tx_bd_tail]);
+
+		cur_p->phys = q->tx_bufs_dma +
+			      (q->tx_buf[q->tx_bd_tail] - q->tx_bufs);
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		cur_p->cntrl = skb_pagelen(skb) | XMCDMA_BD_CTRL_TXSOF_MASK;
+#else
+		cur_p->cntrl = skb_pagelen(skb) | XAXIDMA_BD_CTRL_TXSOF_MASK;
+#endif
+		goto out;
+	} else {
+		cur_p->phys = dma_map_single(ndev->dev.parent, skb->data,
+					     skb_headlen(skb), DMA_TO_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, cur_p->phys))) {
+			cur_p->phys = 0;
+			spin_unlock_irqrestore(&q->tx_lock, flags);
+			dev_err(&ndev->dev, "TX buffer map failed\n");
+			return NETDEV_TX_BUSY;
+		}
 	}
-	desc_set_phys_addr(lp, phys, cur_p);
-	cur_p->cntrl = skb_headlen(skb) | XAXIDMA_BD_CTRL_TXSOF_MASK;
+	cur_p->tx_desc_mapping = DESC_DMA_MAP_SINGLE;
 
 	for (ii = 0; ii < num_frag; ii++) {
-		if (++lp->tx_bd_tail >= lp->tx_bd_num)
-			lp->tx_bd_tail = 0;
-		cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
-		frag = &skb_shinfo(skb)->frags[ii];
-		phys = dma_map_single(ndev->dev.parent,
-				      skb_frag_address(frag),
-				      skb_frag_size(frag),
-				      DMA_TO_DEVICE);
-		if (unlikely(dma_mapping_error(ndev->dev.parent, phys))) {
-			if (net_ratelimit())
-				netdev_err(ndev, "TX DMA mapping error\n");
-			ndev->stats.tx_dropped++;
-			axienet_free_tx_chain(ndev, orig_tail_ptr, ii + 1,
-					      NULL);
-			lp->tx_bd_tail = orig_tail_ptr;
+		u32 len;
+		skb_frag_t *frag;
 
-			return NETDEV_TX_OK;
-		}
-		desc_set_phys_addr(lp, phys, cur_p);
-		cur_p->cntrl = skb_frag_size(frag);
+		if (++q->tx_bd_tail >= lp->tx_bd_num)
+			q->tx_bd_tail = 0;
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		cur_p = &q->txq_bd_v[q->tx_bd_tail];
+#else
+		cur_p = &q->tx_bd_v[q->tx_bd_tail];
+#endif
+		frag = &skb_shinfo(skb)->frags[ii];
+		len = skb_frag_size(frag);
+		cur_p->phys = skb_frag_dma_map(ndev->dev.parent, frag, 0, len,
+					       DMA_TO_DEVICE);
+		cur_p->cntrl = len;
+		cur_p->tx_desc_mapping = DESC_DMA_MAP_PAGE;
 	}
 
+out:
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p->cntrl |= XMCDMA_BD_CTRL_TXEOF_MASK;
+	tail_p = q->tx_bd_p + sizeof(*q->txq_bd_v) * q->tx_bd_tail;
+#else
 	cur_p->cntrl |= XAXIDMA_BD_CTRL_TXEOF_MASK;
-	cur_p->skb = skb;
+	tail_p = q->tx_bd_p + sizeof(*q->tx_bd_v) * q->tx_bd_tail;
+#endif
+	cur_p->tx_skb = (phys_addr_t)skb;
+	cur_p->tx_skb = (phys_addr_t)skb;
+
+	tail_p = q->tx_bd_p + sizeof(*q->tx_bd_v) * q->tx_bd_tail;
+	/* Ensure BD write before starting transfer */
+	wmb();
 
-	tail_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
 	/* Start the transfer */
-	axienet_dma_out_addr(lp, XAXIDMA_TX_TDESC_OFFSET, tail_p);
-	if (++lp->tx_bd_tail >= lp->tx_bd_num)
-		lp->tx_bd_tail = 0;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id),
+			  tail_p);
+#else
+	axienet_dma_bdout(q, XAXIDMA_TX_TDESC_OFFSET, tail_p);
+#endif
+	if (++q->tx_bd_tail >= lp->tx_bd_num)
+		q->tx_bd_tail = 0;
+
+	/* Stop queue if next transmit may not have space */
+	if (axienet_check_tx_bd_space(q, MAX_SKB_FRAGS + 1)) {
+		netif_stop_queue(ndev);
+
+		/* Matches barrier in axienet_start_xmit_done */
+		smp_mb();
+
+		/* Space might have just been freed - check again */
+		if (!axienet_check_tx_bd_space(q, MAX_SKB_FRAGS + 1))
+			netif_wake_queue(ndev);
+	}
+	spin_unlock_irqrestore(&q->tx_lock, flags);
 
 	return NETDEV_TX_OK;
 }
 
 /**
+ * axienet_start_xmit - Starts the transmission.
+ * @skb:	sk_buff pointer that contains data to be Txed.
+ * @ndev:	Pointer to net_device structure.
+ *
+ * Return: NETDEV_TX_OK, on success
+ *	    NETDEV_TX_BUSY, if any of the descriptors are not free
+ *
+ * This function is invoked from upper layers to initiate transmission. The
+ * function uses the next available free BDs and populates their fields to
+ * start the transmission. Additionally if checksum offloading is supported,
+ * it populates AXI Stream Control fields with appropriate values.
+ */
+static int __maybe_unused axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	u16 map = skb_get_queue_mapping(skb); /* Single dma queue default*/
+
+	return axienet_queue_xmit(skb, ndev, map);
+}
+
+/**
  * axienet_recv - Is called from Axi DMA Rx Isr to complete the received
  *		  BD processing.
  * @ndev:	Pointer to net_device structure.
+ * @budget:	NAPI budget
+ * @q:		Pointer to axienet DMA queue structure
  *
- * This function is invoked from the Axi DMA Rx isr to process the Rx BDs. It
- * does minimal processing and invokes "netif_rx" to complete further
- * processing.
+ * This function is invoked from the Axi DMA Rx isr(poll) to process the Rx BDs
+ * It does minimal processing and invokes "netif_receive_skb" to complete
+ * further processing.
+ * Return: Number of BD's processed.
  */
-static void axienet_recv(struct net_device *ndev)
+static int axienet_recv(struct net_device *ndev, int budget,
+			struct axienet_dma_q *q)
 {
 	u32 length;
 	u32 csumstatus;
@@ -825,177 +1544,239 @@
 	dma_addr_t tail_p = 0;
 	struct axienet_local *lp = netdev_priv(ndev);
 	struct sk_buff *skb, *new_skb;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	struct aximcdma_bd *cur_p;
+#else
 	struct axidma_bd *cur_p;
+#endif
+	unsigned int numbdfree = 0;
 
-	cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
-
-	while ((cur_p->status & XAXIDMA_BD_STS_COMPLETE_MASK)) {
-		dma_addr_t phys;
+	/* Get relevat BD status value */
+	rmb();
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	cur_p = &q->rxq_bd_v[q->rx_bd_ci];
+#else
+	cur_p = &q->rx_bd_v[q->rx_bd_ci];
+#endif
 
-		tail_p = lp->rx_bd_p + sizeof(*lp->rx_bd_v) * lp->rx_bd_ci;
+	while ((numbdfree < budget) &&
+	       (cur_p->status & XAXIDMA_BD_STS_COMPLETE_MASK)) {
+		new_skb = netdev_alloc_skb(ndev, lp->max_frm_size);
+		if (!new_skb)
+			break;
 
-		phys = desc_get_phys_addr(lp, cur_p);
-		dma_unmap_single(ndev->dev.parent, phys, lp->max_frm_size,
+		/* Ensure we see complete descriptor update */
+		dma_rmb();
+		dma_unmap_single(ndev->dev.parent, cur_p->phys,
+				 lp->max_frm_size,
 				 DMA_FROM_DEVICE);
 
-		skb = cur_p->skb;
-		cur_p->skb = NULL;
-		length = cur_p->app4 & 0x0000FFFF;
-
-		skb_put(skb, length);
-		skb->protocol = eth_type_trans(skb, ndev);
-		/*skb_checksum_none_assert(skb);*/
-		skb->ip_summed = CHECKSUM_NONE;
-
-		/* if we're doing Rx csum offload, set it up */
-		if (lp->features & XAE_FEATURE_FULL_RX_CSUM) {
-			csumstatus = (cur_p->app2 &
-				      XAE_FULL_CSUM_STATUS_MASK) >> 3;
-			if ((csumstatus == XAE_IP_TCP_CSUM_VALIDATED) ||
-			    (csumstatus == XAE_IP_UDP_CSUM_VALIDATED)) {
-				skb->ip_summed = CHECKSUM_UNNECESSARY;
-			}
-		} else if ((lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) != 0 &&
-			   skb->protocol == htons(ETH_P_IP) &&
-			   skb->len > 64) {
-			skb->csum = be32_to_cpu(cur_p->app3 & 0xFFFF);
-			skb->ip_summed = CHECKSUM_COMPLETE;
-		}
+		skb = (struct sk_buff *)(cur_p->sw_id_offset);
+
+		/* skb could be NULL if a previous pass already received the
+		 * packet for this slot in the ring, but failed to refill it
+		 * with a newly allocated buffer. In this case, don't try to
+		 * receive it again.
+		 */
+		if (likely(skb)) {
+			if (lp->eth_hasnobuf ||
+			    lp->axienet_config->mactype != XAXIENET_1G)
+				length = cur_p->status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+			else
+				length = cur_p->app4 & 0x0000FFFF;
+
+			skb_put(skb, length);
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+				if ((lp->tstamp_config.rx_filter == HWTSTAMP_FILTER_ALL ||
+				     lp->eth_hasptp) &&
+				     lp->axienet_config->mactype != XAXIENET_10G_25G &&
+				     lp->axienet_config->mactype != XAXIENET_MRMAC) {
+					u32 sec, nsec;
+					u64 time64;
+					struct skb_shared_hwtstamps *shhwtstamps;
+
+					if (lp->axienet_config->mactype == XAXIENET_1G ||
+					    lp->axienet_config->mactype == XAXIENET_2_5G) {
+						/* The first 8 bytes will be the timestamp */
+						memcpy(&sec, &skb->data[0], 4);
+						memcpy(&nsec, &skb->data[4], 4);
+
+						sec = cpu_to_be32(sec);
+						nsec = cpu_to_be32(nsec);
+					} else {
+						/* The first 8 bytes will be the timestamp */
+						memcpy(&nsec, &skb->data[0], 4);
+						memcpy(&sec, &skb->data[4], 4);
+					}
+
+					/* Remove these 8 bytes from the buffer */
+					skb_pull(skb, 8);
+					time64 = sec * NS_PER_SEC + nsec;
+					shhwtstamps = skb_hwtstamps(skb);
+					shhwtstamps->hwtstamp = ns_to_ktime(time64);
+				} else if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+					   lp->axienet_config->mactype == XAXIENET_MRMAC) {
+					axienet_rx_hwtstamp(lp, skb);
+				}
+#endif
+			skb->protocol = eth_type_trans(skb, ndev);
+			/*skb_checksum_none_assert(skb);*/
+			skb->ip_summed = CHECKSUM_NONE;
+
+			/* if we're doing Rx csum offload, set it up */
+			if (lp->features & XAE_FEATURE_FULL_RX_CSUM &&
+			    lp->axienet_config->mactype == XAXIENET_1G &&
+			    !lp->eth_hasnobuf) {
+				csumstatus = (cur_p->app2 &
+					      XAE_FULL_CSUM_STATUS_MASK) >> 3;
+				if (csumstatus == XAE_IP_TCP_CSUM_VALIDATED ||
+				    csumstatus == XAE_IP_UDP_CSUM_VALIDATED) {
+					skb->ip_summed = CHECKSUM_UNNECESSARY;
+				}
+			} else if ((lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) != 0 &&
+				   skb->protocol == htons(ETH_P_IP) &&
+				   skb->len > 64 && !lp->eth_hasnobuf &&
+				   (lp->axienet_config->mactype == XAXIENET_1G)) {
+				skb->csum = be32_to_cpu(cur_p->app3 & 0xFFFF);
+				skb->ip_summed = CHECKSUM_COMPLETE;
+			}
 
-		netif_rx(skb);
+			netif_receive_skb(skb);
 
-		size += length;
-		packets++;
+			size += length;
+			packets++;
+		}
 
-		new_skb = netdev_alloc_skb_ip_align(ndev, lp->max_frm_size);
-		if (!new_skb)
-			return;
+		/* Ensure that the skb is completely updated
+		 * prio to mapping the DMA
+		 */
+		wmb();
 
-		phys = dma_map_single(ndev->dev.parent, new_skb->data,
-				      lp->max_frm_size,
-				      DMA_FROM_DEVICE);
-		if (unlikely(dma_mapping_error(ndev->dev.parent, phys))) {
-			if (net_ratelimit())
-				netdev_err(ndev, "RX DMA mapping error\n");
+		cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
+					     lp->max_frm_size,
+					   DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, cur_p->phys))) {
+			cur_p->phys = 0;
 			dev_kfree_skb(new_skb);
-			return;
+			dev_err(lp->dev, "RX buffer map failed\n");
+			break;
 		}
-		desc_set_phys_addr(lp, phys, cur_p);
-
 		cur_p->cntrl = lp->max_frm_size;
 		cur_p->status = 0;
-		cur_p->skb = new_skb;
+		cur_p->sw_id_offset = (phys_addr_t)new_skb;
 
-		if (++lp->rx_bd_ci >= lp->rx_bd_num)
-			lp->rx_bd_ci = 0;
-		cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
+		/* Only update tail_p to mark this slot as usable after it has
+		 * been successfully refilled.
+		 */
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		tail_p = q->rx_bd_p + sizeof(*q->rxq_bd_v) * q->rx_bd_ci;
+#else
+		tail_p = q->rx_bd_p + sizeof(*q->rx_bd_v) * q->rx_bd_ci;
+#endif
+
+		if (++q->rx_bd_ci >= lp->rx_bd_num)
+			q->rx_bd_ci = 0;
+
+		/* Get relevat BD status value */
+		rmb();
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		cur_p = &q->rxq_bd_v[q->rx_bd_ci];
+#else
+		cur_p = &q->rx_bd_v[q->rx_bd_ci];
+#endif
+		numbdfree++;
 	}
 
 	ndev->stats.rx_packets += packets;
 	ndev->stats.rx_bytes += size;
+	q->rx_packets += packets;
+	q->rx_bytes += size;
 
-	if (tail_p)
-		axienet_dma_out_addr(lp, XAXIDMA_RX_TDESC_OFFSET, tail_p);
-}
-
-/**
- * axienet_tx_irq - Tx Done Isr.
- * @irq:	irq number
- * @_ndev:	net_device pointer
- *
- * Return: IRQ_HANDLED if device generated a TX interrupt, IRQ_NONE otherwise.
- *
- * This is the Axi DMA Tx done Isr. It invokes "axienet_start_xmit_done"
- * to complete the BD processing.
- */
-static irqreturn_t axienet_tx_irq(int irq, void *_ndev)
-{
-	u32 cr;
-	unsigned int status;
-	struct net_device *ndev = _ndev;
-	struct axienet_local *lp = netdev_priv(ndev);
-
-	status = axienet_dma_in32(lp, XAXIDMA_TX_SR_OFFSET);
-	if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
-		axienet_dma_out32(lp, XAXIDMA_TX_SR_OFFSET, status);
-		axienet_start_xmit_done(lp->ndev);
-		goto out;
+	if (tail_p) {
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id) +
+				  q->rx_offset, tail_p);
+#else
+		axienet_dma_bdout(q, XAXIDMA_RX_TDESC_OFFSET, tail_p);
+#endif
 	}
-	if (!(status & XAXIDMA_IRQ_ALL_MASK))
-		return IRQ_NONE;
-	if (status & XAXIDMA_IRQ_ERROR_MASK) {
-		dev_err(&ndev->dev, "DMA Tx error 0x%x\n", status);
-		dev_err(&ndev->dev, "Current BD is at: 0x%x%08x\n",
-			(lp->tx_bd_v[lp->tx_bd_ci]).phys_msb,
-			(lp->tx_bd_v[lp->tx_bd_ci]).phys);
-
-		cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-		/* Disable coalesce, delay timer and error interrupts */
-		cr &= (~XAXIDMA_IRQ_ALL_MASK);
-		/* Write to the Tx channel control register */
-		axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
-
-		cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-		/* Disable coalesce, delay timer and error interrupts */
-		cr &= (~XAXIDMA_IRQ_ALL_MASK);
-		/* Write to the Rx channel control register */
-		axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
 
-		schedule_work(&lp->dma_err_task);
-		axienet_dma_out32(lp, XAXIDMA_TX_SR_OFFSET, status);
-	}
-out:
-	return IRQ_HANDLED;
+	return numbdfree;
 }
 
 /**
- * axienet_rx_irq - Rx Isr.
- * @irq:	irq number
- * @_ndev:	net_device pointer
+ * xaxienet_rx_poll - Poll routine for rx packets (NAPI)
+ * @napi:	napi structure pointer
+ * @quota:	Max number of rx packets to be processed.
  *
- * Return: IRQ_HANDLED if device generated a RX interrupt, IRQ_NONE otherwise.
+ * This is the poll routine for rx part.
+ * It will process the packets maximux quota value.
  *
- * This is the Axi DMA Rx Isr. It invokes "axienet_recv" to complete the BD
- * processing.
+ * Return: number of packets received
  */
-static irqreturn_t axienet_rx_irq(int irq, void *_ndev)
+int xaxienet_rx_poll(struct napi_struct *napi, int quota)
 {
-	u32 cr;
-	unsigned int status;
-	struct net_device *ndev = _ndev;
+	struct net_device *ndev = napi->dev;
 	struct axienet_local *lp = netdev_priv(ndev);
+	int work_done = 0;
+	unsigned int status, cr;
 
-	status = axienet_dma_in32(lp, XAXIDMA_RX_SR_OFFSET);
-	if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
-		axienet_dma_out32(lp, XAXIDMA_RX_SR_OFFSET, status);
-		axienet_recv(lp->ndev);
-		goto out;
+	int map = napi - lp->napi;
+
+	struct axienet_dma_q *q = lp->dq[map];
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	spin_lock(&q->rx_lock);
+	status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset);
+	while ((status & (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK)) &&
+	       (work_done < quota)) {
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset, status);
+		if (status & XMCDMA_IRQ_ERR_MASK) {
+			dev_err(lp->dev, "Rx error 0x%x\n\r", status);
+			break;
+		}
+		work_done += axienet_recv(lp->ndev, quota - work_done, q);
+		status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+					  q->rx_offset);
+	}
+	spin_unlock(&q->rx_lock);
+#else
+	spin_lock(&q->rx_lock);
+
+	status = axienet_dma_in32(q, XAXIDMA_RX_SR_OFFSET);
+	while ((status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) &&
+	       (work_done < quota)) {
+		axienet_dma_out32(q, XAXIDMA_RX_SR_OFFSET, status);
+		if (status & XAXIDMA_IRQ_ERROR_MASK) {
+			dev_err(lp->dev, "Rx error 0x%x\n\r", status);
+			break;
+		}
+		work_done += axienet_recv(lp->ndev, quota - work_done, q);
+		status = axienet_dma_in32(q, XAXIDMA_RX_SR_OFFSET);
 	}
-	if (!(status & XAXIDMA_IRQ_ALL_MASK))
-		return IRQ_NONE;
-	if (status & XAXIDMA_IRQ_ERROR_MASK) {
-		dev_err(&ndev->dev, "DMA Rx error 0x%x\n", status);
-		dev_err(&ndev->dev, "Current BD is at: 0x%x%08x\n",
-			(lp->rx_bd_v[lp->rx_bd_ci]).phys_msb,
-			(lp->rx_bd_v[lp->rx_bd_ci]).phys);
-
-		cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-		/* Disable coalesce, delay timer and error interrupts */
-		cr &= (~XAXIDMA_IRQ_ALL_MASK);
-		/* Finally write to the Tx channel control register */
-		axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
-
-		cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-		/* Disable coalesce, delay timer and error interrupts */
-		cr &= (~XAXIDMA_IRQ_ALL_MASK);
-		/* write to the Rx channel control register */
-		axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
+	spin_unlock(&q->rx_lock);
+#endif
 
-		schedule_work(&lp->dma_err_task);
-		axienet_dma_out32(lp, XAXIDMA_RX_SR_OFFSET, status);
+	if (work_done < quota) {
+		napi_complete(napi);
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		/* Enable the interrupts again */
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      XMCDMA_RX_OFFSET);
+		cr |= (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK);
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  XMCDMA_RX_OFFSET, cr);
+#else
+		/* Enable the interrupts again */
+		cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		cr |= (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK);
+		axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+#endif
 	}
-out:
-	return IRQ_HANDLED;
+
+	return work_done;
 }
 
 /**
@@ -1027,8 +1808,6 @@
 	return IRQ_HANDLED;
 }
 
-static void axienet_dma_err_handler(struct work_struct *work);
-
 /**
  * axienet_open - Driver open routine.
  * @ndev:	Pointer to net_device structure
@@ -1036,66 +1815,230 @@
  * Return: 0, on success.
  *	    non-zero error value on failure
  *
- * This is the driver open routine. It calls phylink_start to start the
- * PHY device.
+ * This is the driver open routine. It calls phy_start to start the PHY device.
  * It also allocates interrupt service routines, enables the interrupt lines
  * and ISR handling. Axi Ethernet core is reset through Axi DMA core. Buffer
  * descriptors are initialized.
  */
-static int axienet_open(struct net_device *ndev)
+static int __maybe_unused axienet_open(struct net_device *ndev)
 {
-	int ret;
+	int ret = 0, i = 0;
 	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	u32 reg, err;
+	struct phy_device *phydev = NULL;
 
-	dev_dbg(&ndev->dev, "axienet_open()\n");
+	ret  = axienet_device_reset(ndev);
+	if (ret < 0) {
+		dev_err(lp->dev, "axienet_device_reset failed\n");
+		return ret;
+	}
 
-	/* When we do an Axi Ethernet reset, it resets the complete core
-	 * including the MDIO. MDIO must be disabled before resetting.
-	 * Hold MDIO bus lock to avoid MDIO accesses during the reset.
-	 */
-	axienet_lock_mii(lp);
-	ret = axienet_device_reset(ndev);
-	axienet_unlock_mii(lp);
+	if (lp->phy_node) {
+		phydev = of_phy_connect(lp->ndev, lp->phy_node,
+					axienet_adjust_link,
+					lp->phy_flags,
+					lp->phy_mode);
+
+		if (!phydev)
+			dev_err(lp->dev, "of_phy_connect() failed\n");
+		else
+			phy_start(phydev);
+	}
+		/* Enable tasklets for Axi DMA error handling */
+		for_each_rx_dma_queue(lp, i) {
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+			tasklet_init(&lp->dma_err_tasklet[i],
+				     axienet_mcdma_err_handler,
+				     (unsigned long)lp->dq[i]);
+#else
+			tasklet_init(&lp->dma_err_tasklet[i],
+				     axienet_dma_err_handler,
+				     (unsigned long)lp->dq[i]);
+#endif
 
-	ret = phylink_of_phy_connect(lp->phylink, lp->dev->of_node, 0);
-	if (ret) {
-		dev_err(lp->dev, "phylink_of_phy_connect() failed: %d\n", ret);
-		return ret;
+			/* Enable NAPI scheduling before enabling Axi DMA Rx
+			 * IRQ, or you might run into a race condition; the RX
+			 * ISR disables IRQ processing before scheduling the
+			 * NAPI function to complete the processing. If NAPI
+			 * scheduling is (still) disabled at that time, no more
+			 * RX IRQs will be processed as only the NAPI function
+			 * re-enables them!
+			 */
+			napi_enable(&lp->napi[i]);
+		}
+		for_each_tx_dma_queue(lp, i) {
+			struct axienet_dma_q *q = lp->dq[i];
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+			/* Enable interrupts for Axi MCDMA Tx */
+			ret = request_irq(q->tx_irq, axienet_mcdma_tx_irq,
+					  IRQF_SHARED, ndev->name, ndev);
+			if (ret)
+				goto err_tx_irq;
+#else
+			/* Enable interrupts for Axi DMA Tx */
+			ret = request_irq(q->tx_irq, axienet_tx_irq,
+					  0, ndev->name, ndev);
+			if (ret)
+				goto err_tx_irq;
+#endif
+		}
+
+		for_each_rx_dma_queue(lp, i) {
+			struct axienet_dma_q *q = lp->dq[i];
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+			/* Enable interrupts for Axi MCDMA Rx */
+			ret = request_irq(q->rx_irq, axienet_mcdma_rx_irq,
+					  IRQF_SHARED, ndev->name, ndev);
+			if (ret)
+				goto err_rx_irq;
+#else
+			/* Enable interrupts for Axi DMA Rx */
+			ret = request_irq(q->rx_irq, axienet_rx_irq,
+					  0, ndev->name, ndev);
+			if (ret)
+				goto err_rx_irq;
+#endif
+		}
+
+	if (lp->phy_mode == PHY_INTERFACE_MODE_USXGMII) {
+		netdev_dbg(ndev, "RX reg: 0x%x\n",
+			   axienet_ior(lp, XXV_RCW1_OFFSET));
+		/* USXGMII setup at selected speed */
+		reg = axienet_ior(lp, XXV_USXGMII_AN_OFFSET);
+		reg &= ~USXGMII_RATE_MASK;
+		netdev_dbg(ndev, "usxgmii_rate %d\n", lp->usxgmii_rate);
+		switch (lp->usxgmii_rate) {
+		case SPEED_1000:
+			reg |= USXGMII_RATE_1G;
+			break;
+		case SPEED_2500:
+			reg |= USXGMII_RATE_2G5;
+			break;
+		case SPEED_10:
+			reg |= USXGMII_RATE_10M;
+			break;
+		case SPEED_100:
+			reg |= USXGMII_RATE_100M;
+			break;
+		case SPEED_5000:
+			reg |= USXGMII_RATE_5G;
+			break;
+		case SPEED_10000:
+			reg |= USXGMII_RATE_10G;
+			break;
+		default:
+			reg |= USXGMII_RATE_1G;
+		}
+		reg |= USXGMII_FD;
+		reg |= (USXGMII_EN | USXGMII_LINK_STS);
+		axienet_iow(lp, XXV_USXGMII_AN_OFFSET, reg);
+		reg |= USXGMII_AN_EN;
+		axienet_iow(lp, XXV_USXGMII_AN_OFFSET, reg);
+		/* AN Restart bit should be reset, set and then reset as per
+		 * spec with a 1 ms delay for a raising edge trigger
+		 */
+		axienet_iow(lp, XXV_USXGMII_AN_OFFSET,
+			    reg & ~USXGMII_AN_RESTART);
+		mdelay(1);
+		axienet_iow(lp, XXV_USXGMII_AN_OFFSET,
+			    reg | USXGMII_AN_RESTART);
+		mdelay(1);
+		axienet_iow(lp, XXV_USXGMII_AN_OFFSET,
+			    reg & ~USXGMII_AN_RESTART);
+
+		/* Check block lock bit to make sure RX path is ok with
+		 * USXGMII initialization.
+		 */
+		err = readl_poll_timeout(lp->regs + XXV_STATRX_BLKLCK_OFFSET,
+					 reg, (reg & XXV_RX_BLKLCK_MASK),
+					 100, DELAY_OF_ONE_MILLISEC);
+		if (err) {
+			netdev_err(ndev, "%s: USXGMII Block lock bit not set",
+				   __func__);
+			ret = -ENODEV;
+			goto err_eth_irq;
+		}
+
+		err = readl_poll_timeout(lp->regs + XXV_USXGMII_AN_STS_OFFSET,
+					 reg, (reg & USXGMII_AN_STS_COMP_MASK),
+					 1000000, DELAY_OF_ONE_MILLISEC);
+		if (err) {
+			netdev_err(ndev, "%s: USXGMII AN not complete",
+				   __func__);
+			ret = -ENODEV;
+			goto err_eth_irq;
+		}
+
+		netdev_info(ndev, "USXGMII setup at %d\n", lp->usxgmii_rate);
 	}
 
-	phylink_start(lp->phylink);
+	if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		u32 val;
 
-	/* Enable worker thread for Axi DMA error handling */
-	INIT_WORK(&lp->dma_err_task, axienet_dma_err_handler);
+		/* Reset MRMAC */
+		axienet_mrmac_reset(lp);
+
+		mdelay(MRMAC_RESET_DELAY);
+		/* Check for block lock bit to be set. This ensures that
+		 * MRMAC ethernet IP is functioning normally.
+		 */
+		axienet_iow(lp, MRMAC_TX_STS_OFFSET, MRMAC_STS_ALL_MASK);
+		axienet_iow(lp, MRMAC_RX_STS_OFFSET, MRMAC_STS_ALL_MASK);
+		err = readx_poll_timeout(axienet_get_mrmac_blocklock, lp, val,
+					 (val & MRMAC_RX_BLKLCK_MASK), 10, DELAY_OF_ONE_MILLISEC);
+		if (err)
+			netdev_err(ndev, "MRMAC block lock not complete! Cross-check the MAC ref clock configuration\n");
+
+		err = readx_poll_timeout(axienet_get_mrmac_rx_status, lp, val,
+					 (val & MRMAC_RX_STATUS_MASK), 10, DELAY_OF_ONE_MILLISEC);
+		if (err) {
+			netdev_err(ndev, "MRMAC Link is down!\n");
+			ret = -ENODEV;
+			goto err_eth_irq;
+		}
+
+		axienet_iow(lp, MRMAC_STATRX_VALID_CTRL_OFFSET, MRMAC_STS_ALL_MASK);
+		val = axienet_ior(lp, MRMAC_STATRX_VALID_CTRL_OFFSET);
+
+		if (!(val & MRMAC_RX_VALID_MASK)) {
+			netdev_err(ndev, "MRMAC Link is down! No recent RX Valid Control Code\n");
+			ret = -ENODEV;
+			goto err_eth_irq;
+		}
+		netdev_info(ndev, "MRMAC setup at %d\n", lp->mrmac_rate);
+		axienet_iow(lp, MRMAC_TICK_OFFSET, MRMAC_TICK_TRIGGER);
+	}
 
-	/* Enable interrupts for Axi DMA Tx */
-	ret = request_irq(lp->tx_irq, axienet_tx_irq, IRQF_SHARED,
-			  ndev->name, ndev);
-	if (ret)
-		goto err_tx_irq;
-	/* Enable interrupts for Axi DMA Rx */
-	ret = request_irq(lp->rx_irq, axienet_rx_irq, IRQF_SHARED,
-			  ndev->name, ndev);
-	if (ret)
-		goto err_rx_irq;
 	/* Enable interrupts for Axi Ethernet core (if defined) */
-	if (lp->eth_irq > 0) {
+	if (!lp->eth_hasnobuf && lp->axienet_config->mactype == XAXIENET_1G) {
 		ret = request_irq(lp->eth_irq, axienet_eth_irq, IRQF_SHARED,
 				  ndev->name, ndev);
 		if (ret)
 			goto err_eth_irq;
 	}
 
+	netif_tx_start_all_queues(ndev);
 	return 0;
 
 err_eth_irq:
-	free_irq(lp->rx_irq, ndev);
+	while (i--) {
+		q = lp->dq[i];
+		free_irq(q->rx_irq, ndev);
+	}
+	i = lp->num_tx_queues;
 err_rx_irq:
-	free_irq(lp->tx_irq, ndev);
+	while (i--) {
+		q = lp->dq[i];
+		free_irq(q->tx_irq, ndev);
+	}
 err_tx_irq:
-	phylink_stop(lp->phylink);
-	phylink_disconnect_phy(lp->phylink);
-	cancel_work_sync(&lp->dma_err_task);
+	for_each_rx_dma_queue(lp, i)
+		napi_disable(&lp->napi[i]);
+	if (phydev)
+		phy_disconnect(phydev);
+	for_each_rx_dma_queue(lp, i)
+		tasklet_kill(&lp->dma_err_tasklet[i]);
 	dev_err(lp->dev, "request_irq() failed\n");
 	return ret;
 }
@@ -1106,7 +2049,7 @@
  *
  * Return: 0, on success.
  *
- * This is the driver stop routine. It calls phylink_disconnect to stop the PHY
+ * This is the driver stop routine. It calls phy_disconnect to stop the PHY
  * device. It also removes the interrupt handlers and disables the interrupts.
  * The Axi DMA Tx/Rx BDs are released.
  */
@@ -1114,52 +2057,60 @@
 {
 	u32 cr, sr;
 	int count;
+	u32 i;
 	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
 
 	dev_dbg(&ndev->dev, "axienet_close()\n");
 
-	phylink_stop(lp->phylink);
-	phylink_disconnect_phy(lp->phylink);
-
-	axienet_setoptions(ndev, lp->options &
+	lp->axienet_config->setoptions(ndev, lp->options &
 			   ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
 
-	cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	cr &= ~(XAXIDMA_CR_RUNSTOP_MASK | XAXIDMA_IRQ_ALL_MASK);
-	axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
-
-	cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	cr &= ~(XAXIDMA_CR_RUNSTOP_MASK | XAXIDMA_IRQ_ALL_MASK);
-	axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		cr &= ~(XAXIDMA_CR_RUNSTOP_MASK | XAXIDMA_IRQ_ALL_MASK);
+		axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET, cr);
+
+		cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+		cr &= ~(XAXIDMA_CR_RUNSTOP_MASK | XAXIDMA_IRQ_ALL_MASK);
+		axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, cr);
+
+		axienet_iow(lp, XAE_IE_OFFSET, 0);
+
+		/* Give DMAs a chance to halt gracefully */
+		sr = axienet_dma_in32(q, XAXIDMA_RX_SR_OFFSET);
+		for (count = 0; !(sr & XAXIDMA_SR_HALT_MASK) && count < 5; ++count) {
+			msleep(20);
+			sr = axienet_dma_in32(q, XAXIDMA_RX_SR_OFFSET);
+		}
 
-	axienet_iow(lp, XAE_IE_OFFSET, 0);
+		sr = axienet_dma_in32(q, XAXIDMA_TX_SR_OFFSET);
+		for (count = 0; !(sr & XAXIDMA_SR_HALT_MASK) && count < 5; ++count) {
+			msleep(20);
+			sr = axienet_dma_in32(q, XAXIDMA_TX_SR_OFFSET);
+		}
 
-	/* Give DMAs a chance to halt gracefully */
-	sr = axienet_dma_in32(lp, XAXIDMA_RX_SR_OFFSET);
-	for (count = 0; !(sr & XAXIDMA_SR_HALT_MASK) && count < 5; ++count) {
-		msleep(20);
-		sr = axienet_dma_in32(lp, XAXIDMA_RX_SR_OFFSET);
+		/* Do a reset to ensure DMA is really stopped */
+		__axienet_device_reset(q);
+		free_irq(q->tx_irq, ndev);
 	}
 
-	sr = axienet_dma_in32(lp, XAXIDMA_TX_SR_OFFSET);
-	for (count = 0; !(sr & XAXIDMA_SR_HALT_MASK) && count < 5; ++count) {
-		msleep(20);
-		sr = axienet_dma_in32(lp, XAXIDMA_TX_SR_OFFSET);
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		netif_stop_queue(ndev);
+		napi_disable(&lp->napi[i]);
+		tasklet_kill(&lp->dma_err_tasklet[i]);
+		free_irq(q->rx_irq, ndev);
 	}
-
-	/* Do a reset to ensure DMA is really stopped */
-	axienet_lock_mii(lp);
-	__axienet_device_reset(lp);
-	axienet_unlock_mii(lp);
-
-	cancel_work_sync(&lp->dma_err_task);
-
-	if (lp->eth_irq > 0)
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf)
 		free_irq(lp->eth_irq, ndev);
-	free_irq(lp->tx_irq, ndev);
-	free_irq(lp->rx_irq, ndev);
+
+	if (ndev->phydev)
+		phy_disconnect(ndev->phydev);
 
 	axienet_dma_bd_release(ndev);
+
 	return 0;
 }
 
@@ -1201,23 +2152,180 @@
 static void axienet_poll_controller(struct net_device *ndev)
 {
 	struct axienet_local *lp = netdev_priv(ndev);
-	disable_irq(lp->tx_irq);
-	disable_irq(lp->rx_irq);
-	axienet_rx_irq(lp->tx_irq, ndev);
-	axienet_tx_irq(lp->rx_irq, ndev);
-	enable_irq(lp->tx_irq);
-	enable_irq(lp->rx_irq);
+	int i;
+
+	for_each_tx_dma_queue(lp, i)
+		disable_irq(lp->dq[i]->tx_irq);
+	for_each_rx_dma_queue(lp, i)
+		disable_irq(lp->dq[i]->rx_irq);
+
+	for_each_rx_dma_queue(lp, i)
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		axienet_mcdma_rx_irq(lp->dq[i]->rx_irq, ndev);
+#else
+		axienet_rx_irq(lp->dq[i]->rx_irq, ndev);
+#endif
+	for_each_tx_dma_queue(lp, i)
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		axienet_mcdma_tx_irq(lp->dq[i]->tx_irq, ndev);
+#else
+		axienet_tx_irq(lp->dq[i]->tx_irq, ndev);
+#endif
+	for_each_tx_dma_queue(lp, i)
+		enable_irq(lp->dq[i]->tx_irq);
+	for_each_rx_dma_queue(lp, i)
+		enable_irq(lp->dq[i]->rx_irq);
+}
+#endif
+
+#if defined(CONFIG_XILINX_AXI_EMAC_HWTSTAMP)
+/**
+ *  axienet_set_timestamp_mode - sets up the hardware for the requested mode
+ *  @lp: Pointer to axienet local structure
+ *  @config: the hwtstamp configuration requested
+ *
+ * Return: 0 on success, Negative value on errors
+ */
+static int axienet_set_timestamp_mode(struct axienet_local *lp,
+				      struct hwtstamp_config *config)
+{
+	u32 regval;
+
+	/* reserved for future extensions */
+	if (config->flags)
+		return -EINVAL;
+
+	/* Read the current value in the MAC TX CTRL register */
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		regval = axienet_ior(lp, XAE_TC_OFFSET);
+
+	switch (config->tx_type) {
+	case HWTSTAMP_TX_OFF:
+		regval &= ~XAE_TC_INBAND1588_MASK;
+		break;
+	case HWTSTAMP_TX_ON:
+		config->tx_type = HWTSTAMP_TX_ON;
+		regval |= XAE_TC_INBAND1588_MASK;
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC)
+			axienet_iow(lp, MRMAC_CFG1588_OFFSET, 0x0);
+		break;
+	case HWTSTAMP_TX_ONESTEP_SYNC:
+		config->tx_type = HWTSTAMP_TX_ONESTEP_SYNC;
+		regval |= XAE_TC_INBAND1588_MASK;
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC)
+			axienet_iow(lp, MRMAC_CFG1588_OFFSET, MRMAC_ONE_STEP_EN);
+		break;
+	case HWTSTAMP_TX_ONESTEP_P2P:
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+			config->tx_type = HWTSTAMP_TX_ONESTEP_P2P;
+			axienet_iow(lp, MRMAC_CFG1588_OFFSET, MRMAC_ONE_STEP_EN);
+		} else {
+			return -ERANGE;
+		}
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		axienet_iow(lp, XAE_TC_OFFSET, regval);
+
+	/* Read the current value in the MAC RX RCW1 register */
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		regval = axienet_ior(lp, XAE_RCW1_OFFSET);
+
+	/* On RX always timestamp everything */
+	switch (config->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		regval &= ~XAE_RCW1_INBAND1588_MASK;
+		break;
+	default:
+		config->rx_filter = HWTSTAMP_FILTER_ALL;
+		regval |= XAE_RCW1_INBAND1588_MASK;
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		axienet_iow(lp, XAE_RCW1_OFFSET, regval);
+
+	return 0;
+}
+
+/**
+ * axienet_set_ts_config - user entry point for timestamp mode
+ * @lp: Pointer to axienet local structure
+ * @ifr: ioctl data
+ *
+ * Set hardware to the requested more. If unsupported return an error
+ * with no changes. Otherwise, store the mode for future reference
+ *
+ * Return: 0 on success, Negative value on errors
+ */
+static int axienet_set_ts_config(struct axienet_local *lp, struct ifreq *ifr)
+{
+	struct hwtstamp_config config;
+	int err;
+
+	if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+		return -EFAULT;
+
+	err = axienet_set_timestamp_mode(lp, &config);
+	if (err)
+		return err;
+
+	/* save these settings for future reference */
+	memcpy(&lp->tstamp_config, &config, sizeof(lp->tstamp_config));
+
+	return copy_to_user(ifr->ifr_data, &config,
+			    sizeof(config)) ? -EFAULT : 0;
+}
+
+/**
+ * axienet_get_ts_config - return the current timestamp configuration
+ * to the user
+ * @lp: pointer to axienet local structure
+ * @ifr: ioctl data
+ *
+ * Return: 0 on success, Negative value on errors
+ */
+static int axienet_get_ts_config(struct axienet_local *lp, struct ifreq *ifr)
+{
+	struct hwtstamp_config *config = &lp->tstamp_config;
+
+	return copy_to_user(ifr->ifr_data, config,
+			    sizeof(*config)) ? -EFAULT : 0;
 }
 #endif
 
+/* Ioctl MII Interface */
 static int axienet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 {
+#if defined(CONFIG_XILINX_AXI_EMAC_HWTSTAMP)
 	struct axienet_local *lp = netdev_priv(dev);
+#endif
 
 	if (!netif_running(dev))
 		return -EINVAL;
 
-	return phylink_mii_ioctl(lp->phylink, rq, cmd);
+	switch (cmd) {
+	case SIOCGMIIPHY:
+	case SIOCGMIIREG:
+	case SIOCSMIIREG:
+		if (!dev->phydev)
+			return -EOPNOTSUPP;
+		return phy_mii_ioctl(dev->phydev, rq, cmd);
+#if defined(CONFIG_XILINX_AXI_EMAC_HWTSTAMP)
+	case SIOCSHWTSTAMP:
+		return axienet_set_ts_config(lp, rq);
+	case SIOCGHWTSTAMP:
+		return axienet_get_ts_config(lp, rq);
+#endif
+	default:
+		return -EOPNOTSUPP;
+	}
 }
 
 static const struct net_device_ops axienet_netdev_ops = {
@@ -1245,8 +2353,8 @@
 static void axienet_ethtools_get_drvinfo(struct net_device *ndev,
 					 struct ethtool_drvinfo *ed)
 {
-	strlcpy(ed->driver, DRIVER_NAME, sizeof(ed->driver));
-	strlcpy(ed->version, DRIVER_VERSION, sizeof(ed->version));
+	strscpy(ed->driver, DRIVER_NAME, sizeof(ed->driver));
+	strscpy(ed->version, DRIVER_VERSION, sizeof(ed->version));
 }
 
 /**
@@ -1277,7 +2385,7 @@
 static void axienet_ethtools_get_regs(struct net_device *ndev,
 				      struct ethtool_regs *regs, void *ret)
 {
-	u32 *data = (u32 *) ret;
+	u32 *data = (u32 *)ret;
 	size_t len = sizeof(u32) * AXIENET_REGS_N;
 	struct axienet_local *lp = netdev_priv(ndev);
 
@@ -1313,14 +2421,15 @@
 	data[29] = axienet_ior(lp, XAE_FMI_OFFSET);
 	data[30] = axienet_ior(lp, XAE_AF0_OFFSET);
 	data[31] = axienet_ior(lp, XAE_AF1_OFFSET);
-	data[32] = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	data[33] = axienet_dma_in32(lp, XAXIDMA_TX_SR_OFFSET);
-	data[34] = axienet_dma_in32(lp, XAXIDMA_TX_CDESC_OFFSET);
-	data[35] = axienet_dma_in32(lp, XAXIDMA_TX_TDESC_OFFSET);
-	data[36] = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	data[37] = axienet_dma_in32(lp, XAXIDMA_RX_SR_OFFSET);
-	data[38] = axienet_dma_in32(lp, XAXIDMA_RX_CDESC_OFFSET);
-	data[39] = axienet_dma_in32(lp, XAXIDMA_RX_TDESC_OFFSET);
+	/* Support only single DMA queue */
+	data[32] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_CR_OFFSET);
+	data[33] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_SR_OFFSET);
+	data[34] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_CDESC_OFFSET);
+	data[35] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_TDESC_OFFSET);
+	data[36] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_CR_OFFSET);
+	data[37] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_SR_OFFSET);
+	data[38] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_CDESC_OFFSET);
+	data[39] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_TDESC_OFFSET);
 }
 
 static void axienet_ethtools_get_ringparam(struct net_device *ndev,
@@ -1346,7 +2455,8 @@
 	if (ering->rx_pending > RX_BD_NUM_MAX ||
 	    ering->rx_mini_pending ||
 	    ering->rx_jumbo_pending ||
-	    ering->rx_pending > TX_BD_NUM_MAX)
+	    ering->tx_pending < TX_BD_NUM_MIN ||
+	    ering->tx_pending > TX_BD_NUM_MAX)
 		return -EINVAL;
 
 	if (netif_running(ndev))
@@ -1370,16 +2480,20 @@
 axienet_ethtools_get_pauseparam(struct net_device *ndev,
 				struct ethtool_pauseparam *epauseparm)
 {
+	u32 regval;
 	struct axienet_local *lp = netdev_priv(ndev);
 
-	phylink_ethtool_get_pauseparam(lp->phylink, epauseparm);
+	epauseparm->autoneg  = 0;
+	regval = axienet_ior(lp, XAE_FCC_OFFSET);
+	epauseparm->tx_pause = regval & XAE_FCC_FCTX_MASK;
+	epauseparm->rx_pause = regval & XAE_FCC_FCRX_MASK;
 }
 
 /**
  * axienet_ethtools_set_pauseparam - Set device pause parameter(flow control)
  *				     settings.
  * @ndev:	Pointer to net_device structure
- * @epauseparm:Pointer to ethtool_pauseparam structure
+ * @epauseparm:	Pointer to ethtool_pauseparam structure
  *
  * This implements ethtool command for enabling flow control on Rx and Tx
  * paths. Issue "ethtool -A ethX tx on|off" under linux prompt to execute this
@@ -1391,9 +2505,27 @@
 axienet_ethtools_set_pauseparam(struct net_device *ndev,
 				struct ethtool_pauseparam *epauseparm)
 {
+	u32 regval = 0;
 	struct axienet_local *lp = netdev_priv(ndev);
 
-	return phylink_ethtool_set_pauseparam(lp->phylink, epauseparm);
+	if (netif_running(ndev)) {
+		netdev_err(ndev,
+			   "Please stop netif before applying configuration\n");
+		return -EFAULT;
+	}
+
+	regval = axienet_ior(lp, XAE_FCC_OFFSET);
+	if (epauseparm->tx_pause)
+		regval |= XAE_FCC_FCTX_MASK;
+	else
+		regval &= ~XAE_FCC_FCTX_MASK;
+	if (epauseparm->rx_pause)
+		regval |= XAE_FCC_FCRX_MASK;
+	else
+		regval &= ~XAE_FCC_FCRX_MASK;
+	axienet_iow(lp, XAE_FCC_OFFSET, regval);
+
+	return 0;
 }
 
 /**
@@ -1417,12 +2549,24 @@
 {
 	u32 regval = 0;
 	struct axienet_local *lp = netdev_priv(ndev);
-	regval = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	ecoalesce->rx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
-					     >> XAXIDMA_COALESCE_SHIFT;
-	regval = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	ecoalesce->tx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
-					     >> XAXIDMA_COALESCE_SHIFT;
+	struct axienet_dma_q *q;
+	int i;
+
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+
+		regval = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		ecoalesce->rx_max_coalesced_frames +=
+						(regval & XAXIDMA_COALESCE_MASK)
+						     >> XAXIDMA_COALESCE_SHIFT;
+	}
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		regval = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+		ecoalesce->tx_max_coalesced_frames +=
+						(regval & XAXIDMA_COALESCE_MASK)
+						     >> XAXIDMA_COALESCE_SHIFT;
+	}
 	return 0;
 }
 
@@ -1453,6 +2597,34 @@
 		return -EFAULT;
 	}
 
+	if (ecoalesce->rx_max_coalesced_frames > 255 ||
+	    ecoalesce->tx_max_coalesced_frames > 255) {
+		NL_SET_ERR_MSG(extack, "frames must be less than 256");
+		return -EINVAL;
+	}
+
+	if (ecoalesce->rx_coalesce_usecs ||
+	    ecoalesce->rx_coalesce_usecs_irq ||
+	    ecoalesce->rx_max_coalesced_frames_irq ||
+	    ecoalesce->tx_coalesce_usecs ||
+	    ecoalesce->tx_coalesce_usecs_irq ||
+	    ecoalesce->tx_max_coalesced_frames_irq ||
+	    ecoalesce->stats_block_coalesce_usecs ||
+	    ecoalesce->use_adaptive_rx_coalesce ||
+	    ecoalesce->use_adaptive_tx_coalesce ||
+	    ecoalesce->pkt_rate_low ||
+	    ecoalesce->rx_coalesce_usecs_low ||
+	    ecoalesce->rx_max_coalesced_frames_low ||
+	    ecoalesce->tx_coalesce_usecs_low ||
+	    ecoalesce->tx_max_coalesced_frames_low ||
+	    ecoalesce->pkt_rate_high ||
+	    ecoalesce->rx_coalesce_usecs_high ||
+	    ecoalesce->rx_max_coalesced_frames_high ||
+	    ecoalesce->tx_coalesce_usecs_high ||
+	    ecoalesce->tx_max_coalesced_frames_high ||
+	    ecoalesce->rate_sample_interval)
+		return -EOPNOTSUPP;
+
 	if (ecoalesce->rx_max_coalesced_frames)
 		lp->coalesce_count_rx = ecoalesce->rx_max_coalesced_frames;
 	if (ecoalesce->tx_max_coalesced_frames)
@@ -1461,29 +2633,105 @@
 	return 0;
 }
 
-static int
-axienet_ethtools_get_link_ksettings(struct net_device *ndev,
-				    struct ethtool_link_ksettings *cmd)
+#if defined(CONFIG_XILINX_AXI_EMAC_HWTSTAMP)
+/**
+ * axienet_ethtools_get_ts_info - Get h/w timestamping capabilities.
+ * @ndev:	Pointer to net_device structure
+ * @info:	Pointer to ethtool_ts_info structure
+ *
+ * Return: 0, on success, Non-zero error value on failure.
+ */
+static int axienet_ethtools_get_ts_info(struct net_device *ndev,
+					struct ethtool_ts_info *info)
 {
 	struct axienet_local *lp = netdev_priv(ndev);
 
-	return phylink_ethtool_ksettings_get(lp->phylink, cmd);
+	info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE |
+				SOF_TIMESTAMPING_RX_HARDWARE |
+				SOF_TIMESTAMPING_RAW_HARDWARE;
+	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON) |
+			(1 << HWTSTAMP_TX_ONESTEP_SYNC) |
+			(1 << HWTSTAMP_TX_ONESTEP_P2P);
+	info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) |
+			   (1 << HWTSTAMP_FILTER_ALL);
+	info->phc_index = lp->phc_index;
+
+	return 0;
 }
+#endif
 
-static int
-axienet_ethtools_set_link_ksettings(struct net_device *ndev,
-				    const struct ethtool_link_ksettings *cmd)
+/**
+ * axienet_ethtools_sset_count - Get number of strings that
+ *				 get_strings will write.
+ * @ndev:	Pointer to net_device structure
+ * @sset:	Get the set strings
+ *
+ * Return: number of strings, on success, Non-zero error value on
+ *	   failure.
+ */
+static int axienet_ethtools_sset_count(struct net_device *ndev, int sset)
 {
-	struct axienet_local *lp = netdev_priv(ndev);
+	switch (sset) {
+	case ETH_SS_STATS:
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		return axienet_sset_count(ndev, sset);
+#else
+		return AXIENET_ETHTOOLS_SSTATS_LEN;
+#endif
+	default:
+		return -EOPNOTSUPP;
+	}
+}
 
-	return phylink_ethtool_ksettings_set(lp->phylink, cmd);
+/**
+ * axienet_ethtools_get_stats - Get the extended statistics
+ *				about the device.
+ * @ndev:	Pointer to net_device structure
+ * @stats:	Pointer to ethtool_stats structure
+ * @data:	To store the statistics values
+ *
+ * Return: None.
+ */
+static void axienet_ethtools_get_stats(struct net_device *ndev,
+				       struct ethtool_stats *stats,
+				       u64 *data)
+{
+	unsigned int i = 0;
+
+	data[i++] = ndev->stats.tx_packets;
+	data[i++] = ndev->stats.rx_packets;
+	data[i++] = ndev->stats.tx_bytes;
+	data[i++] = ndev->stats.rx_bytes;
+	data[i++] = ndev->stats.tx_errors;
+	data[i++] = ndev->stats.rx_missed_errors + ndev->stats.rx_frame_errors;
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	axienet_get_stats(ndev, stats, data);
+#endif
 }
 
-static int axienet_ethtools_nway_reset(struct net_device *dev)
+/**
+ * axienet_ethtools_strings - Set of strings that describe
+ *			 the requested objects.
+ * @ndev:	Pointer to net_device structure
+ * @sset:	Get the set strings
+ * @data:	Data of Transmit and Receive statistics
+ *
+ * Return: None.
+ */
+static void axienet_ethtools_strings(struct net_device *ndev, u32 sset, u8 *data)
 {
-	struct axienet_local *lp = netdev_priv(dev);
+	int i;
 
-	return phylink_ethtool_nway_reset(lp->phylink);
+	for (i = 0; i < AXIENET_ETHTOOLS_SSTATS_LEN; i++) {
+		if (sset == ETH_SS_STATS)
+			memcpy(data + i * ETH_GSTRING_LEN,
+			       axienet_get_ethtools_strings_stats[i].name,
+			       ETH_GSTRING_LEN);
+	}
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	axienet_strings(ndev, sset, data);
+#endif
 }
 
 static const struct ethtool_ops axienet_ethtool_ops = {
@@ -1493,341 +2741,464 @@
 	.get_regs       = axienet_ethtools_get_regs,
 	.get_link       = ethtool_op_get_link,
 	.get_ringparam	= axienet_ethtools_get_ringparam,
-	.set_ringparam	= axienet_ethtools_set_ringparam,
+	.set_ringparam  = axienet_ethtools_set_ringparam,
 	.get_pauseparam = axienet_ethtools_get_pauseparam,
 	.set_pauseparam = axienet_ethtools_set_pauseparam,
 	.get_coalesce   = axienet_ethtools_get_coalesce,
 	.set_coalesce   = axienet_ethtools_set_coalesce,
-	.get_link_ksettings = axienet_ethtools_get_link_ksettings,
-	.set_link_ksettings = axienet_ethtools_set_link_ksettings,
-	.nway_reset	= axienet_ethtools_nway_reset,
+	.get_sset_count	= axienet_ethtools_sset_count,
+	.get_ethtool_stats = axienet_ethtools_get_stats,
+	.get_strings = axienet_ethtools_strings,
+#if defined(CONFIG_XILINX_AXI_EMAC_HWTSTAMP)
+	.get_ts_info    = axienet_ethtools_get_ts_info,
+#endif
+	.get_link_ksettings = phy_ethtool_get_link_ksettings,
+	.set_link_ksettings = phy_ethtool_set_link_ksettings,
 };
 
-static void axienet_validate(struct phylink_config *config,
-			     unsigned long *supported,
-			     struct phylink_link_state *state)
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+static int __maybe_unused axienet_mcdma_probe(struct platform_device *pdev,
+					      struct axienet_local *lp,
+					      struct net_device *ndev)
 {
-	struct net_device *ndev = to_net_dev(config->dev);
-	struct axienet_local *lp = netdev_priv(ndev);
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+	int i, ret = 0;
+	struct axienet_dma_q *q;
+	struct device_node *np;
+	struct resource dmares;
+	const char *str;
 
-	/* Only support the mode we are configured for */
-	switch (state->interface) {
-	case PHY_INTERFACE_MODE_NA:
-		break;
-	case PHY_INTERFACE_MODE_1000BASEX:
-	case PHY_INTERFACE_MODE_SGMII:
-		if (lp->switch_x_sgmii)
-			break;
-		fallthrough;
-	default:
-		if (state->interface != lp->phy_mode) {
-			netdev_warn(ndev, "Cannot use PHY mode %s, supported: %s\n",
-				    phy_modes(state->interface),
-				    phy_modes(lp->phy_mode));
-			bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
-			return;
-		}
+	ret = of_property_count_strings(pdev->dev.of_node, "xlnx,channel-ids");
+	if (ret < 0)
+		return -EINVAL;
+
+	for_each_rx_dma_queue(lp, i) {
+		q = kzalloc(sizeof(*q), GFP_KERNEL);
+
+		/* parent */
+		q->lp = lp;
+		lp->dq[i] = q;
+		ret = of_property_read_string_index(pdev->dev.of_node,
+						    "xlnx,channel-ids", i,
+						    &str);
+		ret = kstrtou16(str, 16, &q->chan_id);
+		lp->qnum[i] = i;
+		lp->chan_num[i] = q->chan_id;
+	}
+
+	np = of_parse_phandle(pdev->dev.of_node, "axistream-connected",
+			      0);
+	if (IS_ERR(np)) {
+		dev_err(&pdev->dev, "could not find DMA node\n");
+		return ret;
 	}
 
-	phylink_set(mask, Autoneg);
-	phylink_set_port_modes(mask);
-
-	phylink_set(mask, Asym_Pause);
-	phylink_set(mask, Pause);
-
-	switch (state->interface) {
-	case PHY_INTERFACE_MODE_NA:
-	case PHY_INTERFACE_MODE_1000BASEX:
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_GMII:
-	case PHY_INTERFACE_MODE_RGMII:
-	case PHY_INTERFACE_MODE_RGMII_ID:
-	case PHY_INTERFACE_MODE_RGMII_RXID:
-	case PHY_INTERFACE_MODE_RGMII_TXID:
-		phylink_set(mask, 1000baseX_Full);
-		phylink_set(mask, 1000baseT_Full);
-		if (state->interface == PHY_INTERFACE_MODE_1000BASEX)
-			break;
-		fallthrough;
-	case PHY_INTERFACE_MODE_MII:
-		phylink_set(mask, 100baseT_Full);
-		phylink_set(mask, 10baseT_Full);
-		fallthrough;
-	default:
-		break;
+	ret = of_address_to_resource(np, 0, &dmares);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to get DMA resource\n");
+		return ret;
 	}
 
-	bitmap_and(supported, supported, mask,
-		   __ETHTOOL_LINK_MODE_MASK_NBITS);
-	bitmap_and(state->advertising, state->advertising, mask,
-		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	ret = of_property_read_u8(np, "xlnx,addrwidth", (u8 *)&lp->dma_mask);
+	if (ret < 0 || lp->dma_mask < XAE_DMA_MASK_MIN ||
+	    lp->dma_mask > XAE_DMA_MASK_MAX) {
+		dev_info(&pdev->dev, "missing/invalid xlnx,addrwidth property, using default\n");
+		lp->dma_mask = XAE_DMA_MASK_MIN;
+	}
+
+	lp->mcdma_regs = devm_ioremap_resource(&pdev->dev, &dmares);
+	if (IS_ERR(lp->mcdma_regs)) {
+		dev_err(&pdev->dev, "iormeap failed for the dma\n");
+		ret = PTR_ERR(lp->mcdma_regs);
+		return ret;
+	}
+
+	axienet_mcdma_tx_probe(pdev, np, lp);
+	axienet_mcdma_rx_probe(pdev, lp, ndev);
+
+	return 0;
 }
+#endif
 
-static void axienet_mac_pcs_get_state(struct phylink_config *config,
-				      struct phylink_link_state *state)
+static int __maybe_unused axienet_dma_probe(struct platform_device *pdev,
+					    struct net_device *ndev)
 {
-	struct net_device *ndev = to_net_dev(config->dev);
+	int i, ret;
 	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	struct device_node *np = NULL;
+	struct resource dmares;
 
-	switch (state->interface) {
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_1000BASEX:
-		phylink_mii_c22_pcs_get_state(lp->pcs_phy, state);
-		break;
-	default:
-		break;
+	for_each_rx_dma_queue(lp, i) {
+		q = devm_kzalloc(&pdev->dev, sizeof(*q), GFP_KERNEL);
+		if (!q)
+			return -ENOMEM;
+
+		/* parent */
+		q->lp = lp;
+
+		lp->dq[i] = q;
 	}
-}
 
-static void axienet_mac_an_restart(struct phylink_config *config)
-{
-	struct net_device *ndev = to_net_dev(config->dev);
-	struct axienet_local *lp = netdev_priv(ndev);
+	/* Find the DMA node, map the DMA registers, and decode the DMA IRQs */
+	/* TODO handle error ret */
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+
+		np = of_parse_phandle(pdev->dev.of_node, "axistream-connected",
+				      i);
+		if (np) {
+			ret = of_address_to_resource(np, 0, &dmares);
+			if (ret >= 0) {
+				q->dma_regs = devm_ioremap_resource(&pdev->dev,
+								    &dmares);
+			} else {
+				dev_err(&pdev->dev, "unable to get DMA resource for %pOF\n",
+					np);
+				return -ENODEV;
+			}
+			q->eth_hasdre = of_property_read_bool(np,
+							      "xlnx,include-dre");
+			ret = of_property_read_u8(np, "xlnx,addrwidth",
+						  (u8 *)&lp->dma_mask);
+			if (ret <  0 || lp->dma_mask < XAE_DMA_MASK_MIN ||
+			    lp->dma_mask > XAE_DMA_MASK_MAX) {
+				dev_info(&pdev->dev, "missing/invalid xlnx,addrwidth property, using default\n");
+				lp->dma_mask = XAE_DMA_MASK_MIN;
+			}
 
-	phylink_mii_c22_pcs_an_restart(lp->pcs_phy);
-}
+		} else {
+			dev_err(&pdev->dev, "missing axistream-connected property\n");
+			return -EINVAL;
+		}
+		lp->dq[i]->tx_irq = irq_of_parse_and_map(np, 0);
+		lp->dq[i]->rx_irq = irq_of_parse_and_map(np, 1);
+	}
 
-static int axienet_mac_prepare(struct phylink_config *config, unsigned int mode,
-			       phy_interface_t iface)
-{
-	struct net_device *ndev = to_net_dev(config->dev);
-	struct axienet_local *lp = netdev_priv(ndev);
-	int ret;
+	of_node_put(np);
 
-	switch (iface) {
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_1000BASEX:
-		if (!lp->switch_x_sgmii)
-			return 0;
-
-		ret = mdiobus_write(lp->pcs_phy->bus,
-				    lp->pcs_phy->addr,
-				    XLNX_MII_STD_SELECT_REG,
-				    iface == PHY_INTERFACE_MODE_SGMII ?
-					XLNX_MII_STD_SELECT_SGMII : 0);
-		if (ret < 0)
-			netdev_warn(ndev, "Failed to switch PHY interface: %d\n",
-				    ret);
-		return ret;
-	default:
-		return 0;
+	for_each_rx_dma_queue(lp, i) {
+		struct axienet_dma_q *q = lp->dq[i];
+
+		spin_lock_init(&q->tx_lock);
+		spin_lock_init(&q->rx_lock);
+	}
+
+	for_each_rx_dma_queue(lp, i) {
+		netif_napi_add(ndev, &lp->napi[i], xaxienet_rx_poll,
+			       XAXIENET_NAPI_WEIGHT);
 	}
+
+	return 0;
 }
 
-static void axienet_mac_config(struct phylink_config *config, unsigned int mode,
-			       const struct phylink_link_state *state)
+static int axienet_clk_init(struct platform_device *pdev,
+			    struct clk **axi_aclk, struct clk **axis_clk,
+			    struct clk **ref_clk, struct clk **tmpclk)
 {
-	struct net_device *ndev = to_net_dev(config->dev);
-	struct axienet_local *lp = netdev_priv(ndev);
-	int ret;
+	int err;
 
-	switch (state->interface) {
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_1000BASEX:
-		ret = phylink_mii_c22_pcs_config(lp->pcs_phy, mode,
-						 state->interface,
-						 state->advertising);
-		if (ret < 0)
-			netdev_warn(ndev, "Failed to configure PCS: %d\n",
-				    ret);
-		break;
+	*tmpclk = NULL;
 
-	default:
-		break;
+	/* The "ethernet_clk" is deprecated and will be removed sometime in
+	 * the future. For proper clock usage check axiethernet binding
+	 * documentation.
+	 */
+	*axi_aclk = devm_clk_get(&pdev->dev, "ethernet_clk");
+	if (IS_ERR(*axi_aclk)) {
+		if (PTR_ERR(*axi_aclk) != -ENOENT) {
+			err = PTR_ERR(*axi_aclk);
+			return err;
+		}
+
+		*axi_aclk = devm_clk_get(&pdev->dev, "s_axi_lite_clk");
+		if (IS_ERR(*axi_aclk)) {
+			if (PTR_ERR(*axi_aclk) != -ENOENT) {
+				err = PTR_ERR(*axi_aclk);
+				return err;
+			}
+			*axi_aclk = NULL;
+		}
+
+	} else {
+		dev_warn(&pdev->dev, "ethernet_clk is deprecated and will be removed sometime in the future\n");
 	}
-}
 
-static void axienet_mac_link_down(struct phylink_config *config,
-				  unsigned int mode,
-				  phy_interface_t interface)
-{
-	/* nothing meaningful to do */
+	*axis_clk = devm_clk_get(&pdev->dev, "axis_clk");
+	if (IS_ERR(*axis_clk)) {
+		if (PTR_ERR(*axis_clk) != -ENOENT) {
+			err = PTR_ERR(*axis_clk);
+			return err;
+		}
+		*axis_clk = NULL;
+	}
+
+	*ref_clk = devm_clk_get(&pdev->dev, "ref_clk");
+	if (IS_ERR(*ref_clk)) {
+		if (PTR_ERR(*ref_clk) != -ENOENT) {
+			err = PTR_ERR(*ref_clk);
+			return err;
+		}
+		*ref_clk = NULL;
+	}
+
+	err = clk_prepare_enable(*axi_aclk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable axi_aclk/ethernet_clk (%d)\n", err);
+		return err;
+	}
+
+	err = clk_prepare_enable(*axis_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable axis_clk (%d)\n", err);
+		goto err_disable_axi_aclk;
+	}
+
+	err = clk_prepare_enable(*ref_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable ref_clk (%d)\n", err);
+		goto err_disable_axis_clk;
+	}
+
+	return 0;
+
+err_disable_axis_clk:
+	clk_disable_unprepare(*axis_clk);
+err_disable_axi_aclk:
+	clk_disable_unprepare(*axi_aclk);
+
+	return err;
 }
 
-static void axienet_mac_link_up(struct phylink_config *config,
-				struct phy_device *phy,
-				unsigned int mode, phy_interface_t interface,
-				int speed, int duplex,
-				bool tx_pause, bool rx_pause)
+static int axienet_dma_clk_init(struct platform_device *pdev)
 {
-	struct net_device *ndev = to_net_dev(config->dev);
+	int err;
+	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct axienet_local *lp = netdev_priv(ndev);
-	u32 emmc_reg, fcc_reg;
 
-	emmc_reg = axienet_ior(lp, XAE_EMMC_OFFSET);
-	emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
+	/* The "dma_clk" is deprecated and will be removed sometime in
+	 * the future. For proper clock usage check axiethernet binding
+	 * documentation.
+	 */
+	lp->dma_tx_clk = devm_clk_get(&pdev->dev, "dma_clk");
+	if (IS_ERR(lp->dma_tx_clk)) {
+		if (PTR_ERR(lp->dma_tx_clk) != -ENOENT) {
+			err = PTR_ERR(lp->dma_tx_clk);
+			return err;
+		}
 
-	switch (speed) {
-	case SPEED_1000:
-		emmc_reg |= XAE_EMMC_LINKSPD_1000;
-		break;
-	case SPEED_100:
-		emmc_reg |= XAE_EMMC_LINKSPD_100;
-		break;
-	case SPEED_10:
-		emmc_reg |= XAE_EMMC_LINKSPD_10;
-		break;
-	default:
-		dev_err(&ndev->dev,
-			"Speed other than 10, 100 or 1Gbps is not supported\n");
-		break;
+		lp->dma_tx_clk = devm_clk_get(&pdev->dev, "m_axi_mm2s_aclk");
+		if (IS_ERR(lp->dma_tx_clk)) {
+			if (PTR_ERR(lp->dma_tx_clk) != -ENOENT) {
+				err = PTR_ERR(lp->dma_tx_clk);
+				return err;
+			}
+			lp->dma_tx_clk = NULL;
+		}
+	} else {
+		dev_warn(&pdev->dev, "dma_clk is deprecated and will be removed sometime in the future\n");
 	}
 
-	axienet_iow(lp, XAE_EMMC_OFFSET, emmc_reg);
+	lp->dma_rx_clk = devm_clk_get(&pdev->dev, "m_axi_s2mm_aclk");
+	if (IS_ERR(lp->dma_rx_clk)) {
+		if (PTR_ERR(lp->dma_rx_clk) != -ENOENT) {
+			err = PTR_ERR(lp->dma_rx_clk);
+			return err;
+		}
+		lp->dma_rx_clk = NULL;
+	}
 
-	fcc_reg = axienet_ior(lp, XAE_FCC_OFFSET);
-	if (tx_pause)
-		fcc_reg |= XAE_FCC_FCTX_MASK;
-	else
-		fcc_reg &= ~XAE_FCC_FCTX_MASK;
-	if (rx_pause)
-		fcc_reg |= XAE_FCC_FCRX_MASK;
-	else
-		fcc_reg &= ~XAE_FCC_FCRX_MASK;
-	axienet_iow(lp, XAE_FCC_OFFSET, fcc_reg);
-}
+	lp->dma_sg_clk = devm_clk_get(&pdev->dev, "m_axi_sg_aclk");
+	if (IS_ERR(lp->dma_sg_clk)) {
+		if (PTR_ERR(lp->dma_sg_clk) != -ENOENT) {
+			err = PTR_ERR(lp->dma_sg_clk);
+			return err;
+		}
+		lp->dma_sg_clk = NULL;
+	}
 
-static const struct phylink_mac_ops axienet_phylink_ops = {
-	.validate = axienet_validate,
-	.mac_pcs_get_state = axienet_mac_pcs_get_state,
-	.mac_an_restart = axienet_mac_an_restart,
-	.mac_prepare = axienet_mac_prepare,
-	.mac_config = axienet_mac_config,
-	.mac_link_down = axienet_mac_link_down,
-	.mac_link_up = axienet_mac_link_up,
-};
+	err = clk_prepare_enable(lp->dma_tx_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable tx_clk/dma_clk (%d)\n", err);
+		return err;
+	}
 
-/**
- * axienet_dma_err_handler - Work queue task for Axi DMA Error
- * @work:	pointer to work_struct
- *
- * Resets the Axi DMA and Axi Ethernet devices, and reconfigures the
- * Tx/Rx BDs.
- */
-static void axienet_dma_err_handler(struct work_struct *work)
+	err = clk_prepare_enable(lp->dma_rx_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable rx_clk (%d)\n", err);
+		goto err_disable_txclk;
+	}
+
+	err = clk_prepare_enable(lp->dma_sg_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable sg_clk (%d)\n", err);
+		goto err_disable_rxclk;
+	}
+
+	return 0;
+
+err_disable_rxclk:
+	clk_disable_unprepare(lp->dma_rx_clk);
+err_disable_txclk:
+	clk_disable_unprepare(lp->dma_tx_clk);
+
+	return err;
+}
+
+static void axienet_clk_disable(struct platform_device *pdev)
 {
-	u32 axienet_status;
-	u32 cr, i;
-	struct axienet_local *lp = container_of(work, struct axienet_local,
-						dma_err_task);
-	struct net_device *ndev = lp->ndev;
-	struct axidma_bd *cur_p;
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct axienet_local *lp = netdev_priv(ndev);
 
-	axienet_setoptions(ndev, lp->options &
-			   ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
-	/* When we do an Axi Ethernet reset, it resets the complete core
-	 * including the MDIO. MDIO must be disabled before resetting.
-	 * Hold MDIO bus lock to avoid MDIO accesses during the reset.
+	clk_disable_unprepare(lp->dma_sg_clk);
+	clk_disable_unprepare(lp->dma_tx_clk);
+	clk_disable_unprepare(lp->dma_rx_clk);
+	clk_disable_unprepare(lp->eth_sclk);
+	clk_disable_unprepare(lp->eth_refclk);
+	clk_disable_unprepare(lp->eth_dclk);
+	clk_disable_unprepare(lp->aclk);
+}
+
+static int xxvenet_clk_init(struct platform_device *pdev,
+			    struct clk **axi_aclk, struct clk **axis_clk,
+			    struct clk **tmpclk, struct clk **dclk)
+{
+	int err;
+
+	*tmpclk = NULL;
+
+	/* The "ethernet_clk" is deprecated and will be removed sometime in
+	 * the future. For proper clock usage check axiethernet binding
+	 * documentation.
 	 */
-	axienet_lock_mii(lp);
-	__axienet_device_reset(lp);
-	axienet_unlock_mii(lp);
-
-	for (i = 0; i < lp->tx_bd_num; i++) {
-		cur_p = &lp->tx_bd_v[i];
-		if (cur_p->cntrl) {
-			dma_addr_t addr = desc_get_phys_addr(lp, cur_p);
-
-			dma_unmap_single(ndev->dev.parent, addr,
-					 (cur_p->cntrl &
-					  XAXIDMA_BD_CTRL_LENGTH_MASK),
-					 DMA_TO_DEVICE);
+	*axi_aclk = devm_clk_get(&pdev->dev, "ethernet_clk");
+	if (IS_ERR(*axi_aclk)) {
+		if (PTR_ERR(*axi_aclk) != -ENOENT) {
+			err = PTR_ERR(*axi_aclk);
+			return err;
 		}
-		if (cur_p->skb)
-			dev_kfree_skb_irq(cur_p->skb);
-		cur_p->phys = 0;
-		cur_p->phys_msb = 0;
-		cur_p->cntrl = 0;
-		cur_p->status = 0;
-		cur_p->app0 = 0;
-		cur_p->app1 = 0;
-		cur_p->app2 = 0;
-		cur_p->app3 = 0;
-		cur_p->app4 = 0;
-		cur_p->skb = NULL;
+
+		*axi_aclk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+		if (IS_ERR(*axi_aclk)) {
+			if (PTR_ERR(*axi_aclk) != -ENOENT) {
+				err = PTR_ERR(*axi_aclk);
+				return err;
+			}
+			*axi_aclk = NULL;
+		}
+
+	} else {
+		dev_warn(&pdev->dev, "ethernet_clk is deprecated and will be removed sometime in the future\n");
 	}
 
-	for (i = 0; i < lp->rx_bd_num; i++) {
-		cur_p = &lp->rx_bd_v[i];
-		cur_p->status = 0;
-		cur_p->app0 = 0;
-		cur_p->app1 = 0;
-		cur_p->app2 = 0;
-		cur_p->app3 = 0;
-		cur_p->app4 = 0;
+	*axis_clk = devm_clk_get(&pdev->dev, "rx_core_clk");
+	if (IS_ERR(*axis_clk)) {
+		if (PTR_ERR(*axis_clk) != -ENOENT) {
+			err = PTR_ERR(*axis_clk);
+			return err;
+		}
+		*axis_clk = NULL;
 	}
 
-	lp->tx_bd_ci = 0;
-	lp->tx_bd_tail = 0;
-	lp->rx_bd_ci = 0;
-
-	/* Start updating the Rx channel control register */
-	cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	/* Update the interrupt coalesce count */
-	cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
-	      (XAXIDMA_DFT_RX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
-	/* Update the delay timer count */
-	cr = ((cr & ~XAXIDMA_DELAY_MASK) |
-	      (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
-	/* Enable coalesce, delay timer and error interrupts */
-	cr |= XAXIDMA_IRQ_ALL_MASK;
-	/* Finally write to the Rx channel control register */
-	axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
-
-	/* Start updating the Tx channel control register */
-	cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	/* Update the interrupt coalesce count */
-	cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
-	      (XAXIDMA_DFT_TX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
-	/* Update the delay timer count */
-	cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
-	      (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
-	/* Enable coalesce, delay timer and error interrupts */
-	cr |= XAXIDMA_IRQ_ALL_MASK;
-	/* Finally write to the Tx channel control register */
-	axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
+	*dclk = devm_clk_get(&pdev->dev, "dclk");
+	if (IS_ERR(*dclk)) {
+		if (PTR_ERR(*dclk) != -ENOENT) {
+			err = PTR_ERR(*dclk);
+			return err;
+		}
+		*dclk = NULL;
+	}
 
-	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
-	 * halted state. This will make the Rx side ready for reception.
-	 */
-	axienet_dma_out_addr(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
-	cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
-	axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
-			  cr | XAXIDMA_CR_RUNSTOP_MASK);
-	axienet_dma_out_addr(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
-			     (sizeof(*lp->rx_bd_v) * (lp->rx_bd_num - 1)));
-
-	/* Write to the RS (Run-stop) bit in the Tx channel control register.
-	 * Tx channel is now ready to run. But only after we write to the
-	 * tail pointer register that the Tx channel will start transmitting
-	 */
-	axienet_dma_out_addr(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
-	cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
-	axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
-			  cr | XAXIDMA_CR_RUNSTOP_MASK);
-
-	axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
-	axienet_status &= ~XAE_RCW1_RX_MASK;
-	axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
-
-	axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
-	if (axienet_status & XAE_INT_RXRJECT_MASK)
-		axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
-	axienet_iow(lp, XAE_IE_OFFSET, lp->eth_irq > 0 ?
-		    XAE_INT_RECV_ERROR_MASK : 0);
-	axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+	err = clk_prepare_enable(*axi_aclk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable axi_clk/ethernet_clk (%d)\n", err);
+		return err;
+	}
 
-	/* Sync default options with HW but leave receiver and
-	 * transmitter disabled.
-	 */
-	axienet_setoptions(ndev, lp->options &
-			   ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
-	axienet_set_mac_address(ndev, NULL);
-	axienet_set_multicast_list(ndev);
-	axienet_setoptions(ndev, lp->options);
+	err = clk_prepare_enable(*axis_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable axis_clk (%d)\n", err);
+		goto err_disable_axi_aclk;
+	}
+
+	err = clk_prepare_enable(*dclk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable dclk (%d)\n", err);
+		goto err_disable_axis_clk;
+	}
+
+	return 0;
+
+err_disable_axis_clk:
+	clk_disable_unprepare(*axis_clk);
+err_disable_axi_aclk:
+	clk_disable_unprepare(*axi_aclk);
+
+	return err;
 }
 
+static const struct axienet_config axienet_1g_config = {
+	.mactype = XAXIENET_1G,
+	.setoptions = axienet_setoptions,
+	.clk_init = axienet_clk_init,
+	.tx_ptplen = XAE_TX_PTP_LEN,
+};
+
+static const struct axienet_config axienet_2_5g_config = {
+	.mactype = XAXIENET_2_5G,
+	.setoptions = axienet_setoptions,
+	.clk_init = axienet_clk_init,
+	.tx_ptplen = XAE_TX_PTP_LEN,
+};
+
+static const struct axienet_config axienet_10g_config = {
+	.mactype = XAXIENET_LEGACY_10G,
+	.setoptions = axienet_setoptions,
+	.clk_init = xxvenet_clk_init,
+	.tx_ptplen = XAE_TX_PTP_LEN,
+};
+
+static const struct axienet_config axienet_10g25g_config = {
+	.mactype = XAXIENET_10G_25G,
+	.setoptions = xxvenet_setoptions,
+	.clk_init = xxvenet_clk_init,
+	.tx_ptplen = XXV_TX_PTP_LEN,
+	.ts_header_len = XXVENET_TS_HEADER_LEN,
+};
+
+static const struct axienet_config axienet_usxgmii_config = {
+	.mactype = XAXIENET_10G_25G,
+	.setoptions = xxvenet_setoptions,
+	.clk_init = xxvenet_clk_init,
+	.tx_ptplen = 0,
+};
+
+static const struct axienet_config axienet_mrmac_config = {
+	.mactype = XAXIENET_MRMAC,
+	.setoptions = xxvenet_setoptions,
+	.clk_init = xxvenet_clk_init,
+	.tx_ptplen = XXV_TX_PTP_LEN,
+	.ts_header_len = MRMAC_TS_HEADER_LEN,
+};
+
+/* Match table for of_platform binding */
+static const struct of_device_id axienet_of_match[] = {
+	{ .compatible = "xlnx,axi-ethernet-1.00.a", .data = &axienet_1g_config},
+	{ .compatible = "xlnx,axi-ethernet-1.01.a", .data = &axienet_1g_config},
+	{ .compatible = "xlnx,axi-ethernet-2.01.a", .data = &axienet_1g_config},
+	{ .compatible = "xlnx,axi-2_5-gig-ethernet-1.0",
+						.data = &axienet_2_5g_config},
+	{ .compatible = "xlnx,ten-gig-eth-mac", .data = &axienet_10g_config},
+	{ .compatible = "xlnx,xxv-ethernet-1.0",
+						.data = &axienet_10g25g_config},
+	{ .compatible = "xlnx,xxv-usxgmii-ethernet-1.0",
+					.data = &axienet_usxgmii_config},
+	{ .compatible = "xlnx,mrmac-ethernet-1.0",
+					.data = &axienet_mrmac_config},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, axienet_of_match);
+
 /**
  * axienet_probe - Axi Ethernet probe function.
  * @pdev:	Pointer to platform device structure.
@@ -1842,16 +3213,28 @@
  */
 static int axienet_probe(struct platform_device *pdev)
 {
-	int ret;
+	int (*axienet_clk_init)(struct platform_device *pdev,
+				struct clk **axi_aclk, struct clk **axis_clk,
+				struct clk **ref_clk, struct clk **tmpclk) =
+					axienet_clk_init;
+	int ret = 0;
 	struct device_node *np;
 	struct axienet_local *lp;
 	struct net_device *ndev;
-	struct resource *ethres;
 	u8 mac_addr[ETH_ALEN];
-	int addr_width = 32;
+	struct resource *ethres;
 	u32 value;
+	u16 num_queues = XAE_MAX_QUEUES;
+
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-queues",
+				   &num_queues);
+	if (ret) {
+#ifndef CONFIG_AXIENET_HAS_MCDMA
+			num_queues = 1;
+#endif
+	}
 
-	ndev = alloc_etherdev(sizeof(*lp));
+	ndev = alloc_etherdev_mq(sizeof(*lp), num_queues);
 	if (!ndev)
 		return -ENOMEM;
 
@@ -1871,6 +3254,8 @@
 	lp->ndev = ndev;
 	lp->dev = &pdev->dev;
 	lp->options = XAE_OPTION_DEFAULTS;
+	lp->num_tx_queues = num_queues;
+	lp->num_rx_queues = num_queues;
 	lp->rx_bd_num = RX_BD_NUM_DEFAULT;
 	lp->tx_bd_num = TX_BD_NUM_DEFAULT;
 
@@ -1914,22 +3299,34 @@
 	/* Setup checksum offload, but default to off if not specified */
 	lp->features = 0;
 
+	if (pdev->dev.of_node) {
+		const struct of_device_id *match;
+
+		match = of_match_node(axienet_of_match, pdev->dev.of_node);
+		if (match && match->data) {
+			lp->axienet_config = match->data;
+			axienet_clk_init = lp->axienet_config->clk_init;
+		}
+	}
+
 	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,txcsum", &value);
 	if (!ret) {
+		dev_info(&pdev->dev, "TX_CSUM %d\n", value);
+
 		switch (value) {
 		case 1:
 			lp->csum_offload_on_tx_path =
 				XAE_FEATURE_PARTIAL_TX_CSUM;
 			lp->features |= XAE_FEATURE_PARTIAL_TX_CSUM;
 			/* Can checksum TCP/UDP over IPv4. */
-			ndev->features |= NETIF_F_IP_CSUM;
+			ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
 			break;
 		case 2:
 			lp->csum_offload_on_tx_path =
 				XAE_FEATURE_FULL_TX_CSUM;
 			lp->features |= XAE_FEATURE_FULL_TX_CSUM;
 			/* Can checksum TCP/UDP over IPv4. */
-			ndev->features |= NETIF_F_IP_CSUM;
+			ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
 			break;
 		default:
 			lp->csum_offload_on_tx_path = XAE_NO_CSUM_OFFLOAD;
@@ -1937,6 +3334,8 @@
 	}
 	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,rxcsum", &value);
 	if (!ret) {
+		dev_info(&pdev->dev, "RX_CSUM %d\n", value);
+
 		switch (value) {
 		case 1:
 			lp->csum_offload_on_rx_path =
@@ -1960,111 +3359,208 @@
 	 */
 	of_property_read_u32(pdev->dev.of_node, "xlnx,rxmem", &lp->rxmem);
 
-	lp->switch_x_sgmii = of_property_read_bool(pdev->dev.of_node,
-						   "xlnx,switch-x-sgmii");
+	/* The phy_mode is optional but when it is not specified it should not
+	 *  be a value that alters the driver behavior so set it to an invalid
+	 *  value as the default.
+	 */
+	lp->phy_mode = PHY_INTERFACE_MODE_NA;
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,phy-type", &lp->phy_mode);
+	if (!ret)
+		netdev_warn(ndev, "xlnx,phy-type is deprecated, Please upgrade your device tree to use phy-mode");
+
+	/* Set default USXGMII rate */
+	lp->usxgmii_rate = SPEED_1000;
+	of_property_read_u32(pdev->dev.of_node, "xlnx,usxgmii-rate",
+			     &lp->usxgmii_rate);
+
+	/* Set default MRMAC rate */
+	lp->mrmac_rate = SPEED_10000;
+	of_property_read_u32(pdev->dev.of_node, "xlnx,mrmac-rate",
+			     &lp->mrmac_rate);
+
+	lp->eth_hasnobuf = of_property_read_bool(pdev->dev.of_node,
+						 "xlnx,eth-hasnobuf");
+	lp->eth_hasptp = of_property_read_bool(pdev->dev.of_node,
+					       "xlnx,eth-hasptp");
+
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf)
+		lp->eth_irq = platform_get_irq(pdev, 0);
+
+	if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		struct resource gtpll, gtctrl;
+
+		if (mrmac_pll_reg) {
+			lp->gt_pll = mrmac_gt_pll;
+			lp->gt_ctrl = mrmac_gt_ctrl;
+		} else {
+			np = of_parse_phandle(pdev->dev.of_node,
+					      "xlnx,gtpll", 0);
+			if (IS_ERR(np)) {
+				dev_err(&pdev->dev,
+					"couldn't find GT PLL\n");
+				ret = PTR_ERR(np);
+				goto free_netdev;
+			}
 
-	/* Start with the proprietary, and broken phy_type */
-	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,phy-type", &value);
-	if (!ret) {
-		netdev_warn(ndev, "Please upgrade your device tree binary blob to use phy-mode");
-		switch (value) {
-		case XAE_PHY_TYPE_MII:
-			lp->phy_mode = PHY_INTERFACE_MODE_MII;
-			break;
-		case XAE_PHY_TYPE_GMII:
-			lp->phy_mode = PHY_INTERFACE_MODE_GMII;
-			break;
-		case XAE_PHY_TYPE_RGMII_2_0:
-			lp->phy_mode = PHY_INTERFACE_MODE_RGMII_ID;
-			break;
-		case XAE_PHY_TYPE_SGMII:
-			lp->phy_mode = PHY_INTERFACE_MODE_SGMII;
-			break;
-		case XAE_PHY_TYPE_1000BASE_X:
-			lp->phy_mode = PHY_INTERFACE_MODE_1000BASEX;
-			break;
-		default:
-			ret = -EINVAL;
-			goto cleanup_clk;
+			ret = of_address_to_resource(np, 0, &gtpll);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"unable to get GT PLL resource\n");
+				goto free_netdev;
+			}
+
+			lp->gt_pll = devm_ioremap_resource(&pdev->dev,
+							   &gtpll);
+			if (IS_ERR(lp->gt_pll)) {
+				dev_err(&pdev->dev,
+					"couldn't map GT PLL regs\n");
+				ret = PTR_ERR(lp->gt_pll);
+				goto free_netdev;
+			}
+
+			np = of_parse_phandle(pdev->dev.of_node,
+					      "xlnx,gtctrl", 0);
+			if (IS_ERR(np)) {
+				dev_err(&pdev->dev,
+					"couldn't find GT control\n");
+				ret = PTR_ERR(np);
+				goto free_netdev;
+			}
+
+			ret = of_address_to_resource(np, 0, &gtctrl);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"unable to get GT control resource\n");
+				goto free_netdev;
+			}
+
+			lp->gt_ctrl = devm_ioremap_resource(&pdev->dev,
+							    &gtctrl);
+			if (IS_ERR(lp->gt_ctrl)) {
+				dev_err(&pdev->dev,
+					"couldn't map GT control regs\n");
+				ret = PTR_ERR(lp->gt_ctrl);
+				goto free_netdev;
+			}
+
+			mrmac_gt_pll = lp->gt_pll;
+			mrmac_gt_ctrl = lp->gt_ctrl;
+			mrmac_pll_reg = 1;
 		}
-	} else {
-		ret = of_get_phy_mode(pdev->dev.of_node, &lp->phy_mode);
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+		ret = of_property_read_u32(pdev->dev.of_node, "xlnx,phcindex",
+					   &lp->phc_index);
 		if (ret)
-			goto cleanup_clk;
-	}
-	if (lp->switch_x_sgmii && lp->phy_mode != PHY_INTERFACE_MODE_SGMII &&
-	    lp->phy_mode != PHY_INTERFACE_MODE_1000BASEX) {
-		dev_err(&pdev->dev, "xlnx,switch-x-sgmii only supported with SGMII or 1000BaseX\n");
-		ret = -EINVAL;
-		goto cleanup_clk;
+			dev_warn(&pdev->dev, "No phc index defaulting to 0\n");
+#endif
+		ret = of_property_read_u32(pdev->dev.of_node, "xlnx,gtlane",
+					   &lp->gt_lane);
+		if (ret) {
+			dev_err(&pdev->dev, "MRMAC GT lane information missing\n");
+			goto free_netdev;
+		}
+		dev_info(&pdev->dev, "GT lane: %d\n", lp->gt_lane);
 	}
 
-	/* Find the DMA node, map the DMA registers, and decode the DMA IRQs */
-	np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0);
-	if (np) {
-		struct resource dmares;
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+		struct resource txtsres, rxtsres;
+
+		/* Find AXI Stream FIFO */
+		np = of_parse_phandle(pdev->dev.of_node, "axififo-connected",
+				      0);
+		if (IS_ERR(np)) {
+			dev_err(&pdev->dev, "could not find TX Timestamp FIFO\n");
+			ret = PTR_ERR(np);
+			goto free_netdev;
+		}
 
-		ret = of_address_to_resource(np, 0, &dmares);
+		ret = of_address_to_resource(np, 0, &txtsres);
 		if (ret) {
 			dev_err(&pdev->dev,
-				"unable to get DMA resource\n");
-			of_node_put(np);
-			goto cleanup_clk;
-		}
-		lp->dma_regs = devm_ioremap_resource(&pdev->dev,
-						     &dmares);
-		lp->rx_irq = irq_of_parse_and_map(np, 1);
-		lp->tx_irq = irq_of_parse_and_map(np, 0);
+				"unable to get Tx Timestamp resource\n");
+			goto free_netdev;
+		}
+
+		lp->tx_ts_regs = devm_ioremap_resource(&pdev->dev, &txtsres);
+		if (IS_ERR(lp->tx_ts_regs)) {
+			dev_err(&pdev->dev, "could not map Tx Timestamp regs\n");
+			ret = PTR_ERR(lp->tx_ts_regs);
+			goto free_netdev;
+		}
+
+		if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+		    lp->axienet_config->mactype == XAXIENET_MRMAC) {
+			np = of_parse_phandle(pdev->dev.of_node,
+					      "xlnx,rxtsfifo", 0);
+			if (IS_ERR(np)) {
+				dev_err(&pdev->dev,
+					"couldn't find rx-timestamp FIFO\n");
+				ret = PTR_ERR(np);
+				goto free_netdev;
+			}
+
+			ret = of_address_to_resource(np, 0, &rxtsres);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"unable to get rx-timestamp resource\n");
+				goto free_netdev;
+			}
+
+			lp->rx_ts_regs = devm_ioremap_resource(&pdev->dev,
+							       &rxtsres);
+			if (IS_ERR(lp->rx_ts_regs)) {
+				dev_err(&pdev->dev,
+					"couldn't map rx-timestamp regs\n");
+				ret = PTR_ERR(lp->rx_ts_regs);
+				goto free_netdev;
+			}
+
+			lp->tx_ptpheader = devm_kzalloc(&pdev->dev,
+							lp->axienet_config->ts_header_len,
+							GFP_KERNEL);
+			spin_lock_init(&lp->ptp_tx_lock);
+		}
+
 		of_node_put(np);
-		lp->eth_irq = platform_get_irq_optional(pdev, 0);
-	} else {
-		/* Check for these resources directly on the Ethernet node. */
-		lp->dma_regs = devm_platform_get_and_ioremap_resource(pdev, 1, NULL);
-		lp->rx_irq = platform_get_irq(pdev, 1);
-		lp->tx_irq = platform_get_irq(pdev, 0);
-		lp->eth_irq = platform_get_irq_optional(pdev, 2);
-	}
-	if (IS_ERR(lp->dma_regs)) {
-		dev_err(&pdev->dev, "could not map DMA regs\n");
-		ret = PTR_ERR(lp->dma_regs);
-		goto cleanup_clk;
-	}
-	if ((lp->rx_irq <= 0) || (lp->tx_irq <= 0)) {
-		dev_err(&pdev->dev, "could not determine irqs\n");
-		ret = -ENOMEM;
-		goto cleanup_clk;
-	}
+#endif
+	if (lp->axienet_config->mactype == XAXIENET_10G_25G)
+		lp->xxv_ip_version = axienet_ior(lp, XXV_CONFIG_REVISION);
 
-	/* Autodetect the need for 64-bit DMA pointers.
-	 * When the IP is configured for a bus width bigger than 32 bits,
-	 * writing the MSB registers is mandatory, even if they are all 0.
-	 * We can detect this case by writing all 1's to one such register
-	 * and see if that sticks: when the IP is configured for 32 bits
-	 * only, those registers are RES0.
-	 * Those MSB registers were introduced in IP v7.1, which we check first.
-	 */
-	if ((axienet_ior(lp, XAE_ID_OFFSET) >> 24) >= 0x9) {
-		void __iomem *desc = lp->dma_regs + XAXIDMA_TX_CDESC_OFFSET + 4;
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+		ret = axienet_mcdma_probe(pdev, lp, ndev);
+#else
+		ret = axienet_dma_probe(pdev, ndev);
+#endif
+		if (ret) {
+			pr_err("Getting DMA resource failed\n");
+			goto free_netdev;
+		}
 
-		iowrite32(0x0, desc);
-		if (ioread32(desc) == 0) {	/* sanity check */
-			iowrite32(0xffffffff, desc);
-			if (ioread32(desc) > 0) {
-				lp->features |= XAE_FEATURE_DMA_64BIT;
-				addr_width = 64;
-				dev_info(&pdev->dev,
-					 "autodetected 64-bit DMA range\n");
+		if (dma_set_mask_and_coherent(lp->dev, DMA_BIT_MASK(lp->dma_mask)) != 0) {
+			dev_warn(&pdev->dev, "default to %d-bit dma mask\n", XAE_DMA_MASK_MIN);
+			if (dma_set_mask_and_coherent(lp->dev,
+						      DMA_BIT_MASK(XAE_DMA_MASK_MIN)) != 0) {
+				dev_err(&pdev->dev, "dma_set_mask_and_coherent failed, aborting\n");
+				goto free_netdev;
 			}
-			iowrite32(0x0, desc);
 		}
-	}
 
-	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(addr_width));
+		ret = axienet_dma_clk_init(pdev);
+		if (ret) {
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "DMA clock init failed %d\n", ret);
+			goto free_netdev;
+		}
+
+	ret = axienet_clk_init(pdev, &lp->aclk, &lp->eth_sclk,
+			       &lp->eth_refclk, &lp->eth_dclk);
 	if (ret) {
-		dev_err(&pdev->dev, "No suitable DMA available\n");
-		goto cleanup_clk;
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Ethernet clock init failed %d\n", ret);
+		goto err_disable_clk;
 	}
 
+	lp->eth_irq = platform_get_irq(pdev, 0);
 	/* Check for Ethernet core IRQ (optional) */
 	if (lp->eth_irq <= 0)
 		dev_info(&pdev->dev, "Ethernet core IRQ not defined\n");
@@ -2082,6 +3578,12 @@
 	lp->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD;
 	lp->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD;
 
+	ret = of_get_phy_mode(pdev->dev.of_node, &lp->phy_mode);
+	if (ret < 0)
+		dev_warn(&pdev->dev, "couldn't find phy i/f\n");
+	if (lp->phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+		lp->phy_flags = XAE_PHY_TYPE_1000BASE_X;
+
 	lp->phy_node = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0);
 	if (lp->phy_node) {
 		ret = axienet_mdio_setup(lp);
@@ -2089,55 +3591,32 @@
 			dev_warn(&pdev->dev,
 				 "error registering MDIO bus: %d\n", ret);
 	}
-	if (lp->phy_mode == PHY_INTERFACE_MODE_SGMII ||
-	    lp->phy_mode == PHY_INTERFACE_MODE_1000BASEX) {
-		if (!lp->phy_node) {
-			dev_err(&pdev->dev, "phy-handle required for 1000BaseX/SGMII\n");
-			ret = -EINVAL;
-			goto cleanup_mdio;
-		}
-		lp->pcs_phy = of_mdio_find_device(lp->phy_node);
-		if (!lp->pcs_phy) {
-			ret = -EPROBE_DEFER;
-			goto cleanup_mdio;
-		}
-		lp->phylink_config.pcs_poll = true;
-	}
-
-	lp->phylink_config.dev = &ndev->dev;
-	lp->phylink_config.type = PHYLINK_NETDEV;
-
-	lp->phylink = phylink_create(&lp->phylink_config, pdev->dev.fwnode,
-				     lp->phy_mode,
-				     &axienet_phylink_ops);
-	if (IS_ERR(lp->phylink)) {
-		ret = PTR_ERR(lp->phylink);
-		dev_err(&pdev->dev, "phylink_create error (%i)\n", ret);
-		goto cleanup_mdio;
+
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	/* Create sysfs file entries for the device */
+	ret = axeinet_mcdma_create_sysfs(&lp->dev->kobj);
+	if (ret < 0) {
+		dev_err(lp->dev, "unable to create sysfs entries\n");
+		return ret;
 	}
+#endif
 
 	ret = register_netdev(lp->ndev);
 	if (ret) {
 		dev_err(lp->dev, "register_netdev() error (%i)\n", ret);
-		goto cleanup_phylink;
+		axienet_mdio_teardown(lp);
+		goto cleanup_clk;
 	}
 
 	return 0;
 
-cleanup_phylink:
-	phylink_destroy(lp->phylink);
-
-cleanup_mdio:
-	if (lp->pcs_phy)
-		put_device(&lp->pcs_phy->dev);
-	if (lp->mii_bus)
-		axienet_mdio_teardown(lp);
-	of_node_put(lp->phy_node);
-
 cleanup_clk:
 	clk_bulk_disable_unprepare(XAE_NUM_MISC_CLOCKS, lp->misc_clks);
 	clk_disable_unprepare(lp->axi_clk);
 
+err_disable_clk:
+	axienet_clk_disable(pdev);
+
 free_netdev:
 	free_netdev(ndev);
 
@@ -2148,20 +3627,22 @@
 {
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct axienet_local *lp = netdev_priv(ndev);
+	int i;
 
+		for_each_rx_dma_queue(lp, i)
+			netif_napi_del(&lp->napi[i]);
 	unregister_netdev(ndev);
+	axienet_clk_disable(pdev);
 
-	if (lp->phylink)
-		phylink_destroy(lp->phylink);
-
-	if (lp->pcs_phy)
-		put_device(&lp->pcs_phy->dev);
-
-	axienet_mdio_teardown(lp);
+	if (lp->mii_bus)
+		axienet_mdio_teardown(lp);
 
 	clk_bulk_disable_unprepare(XAE_NUM_MISC_CLOCKS, lp->misc_clks);
 	clk_disable_unprepare(lp->axi_clk);
 
+#ifdef CONFIG_AXIENET_HAS_MCDMA
+	axeinet_mcdma_remove_sysfs(&lp->dev->kobj);
+#endif
 	of_node_put(lp->phy_node);
 	lp->phy_node = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/xilinx_axienet_mcdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/xilinx_axienet_mcdma.c
@@ -0,0 +1,1051 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Xilinx AXI Ethernet (MCDMA programming)
+ *
+ * Copyright (c) 2008 Nissin Systems Co., Ltd.,  Yoshio Kashiwagi
+ * Copyright (c) 2005-2008 DLA Systems,  David H. Lynch Jr. <dhlii@dlasys.net>
+ * Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
+ * Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
+ * Copyright (c) 2010 - 2011 PetaLogix
+ * Copyright (c) 2010 - 2012 Xilinx, Inc.
+ * Copyright (C) 2018 Xilinx, Inc. All rights reserved.
+ *
+ * This file contains helper functions for AXI MCDMA TX and RX programming.
+ */
+
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/of_net.h>
+
+#include "xilinx_axienet.h"
+
+struct axienet_stat {
+	const char *name;
+};
+
+static struct axienet_stat axienet_get_tx_strings_stats[] = {
+	{ "txq0_packets" },
+	{ "txq0_bytes"   },
+	{ "txq1_packets" },
+	{ "txq1_bytes"   },
+	{ "txq2_packets" },
+	{ "txq2_bytes"   },
+	{ "txq3_packets" },
+	{ "txq3_bytes"   },
+	{ "txq4_packets" },
+	{ "txq4_bytes"   },
+	{ "txq5_packets" },
+	{ "txq5_bytes"   },
+	{ "txq6_packets" },
+	{ "txq6_bytes"   },
+	{ "txq7_packets" },
+	{ "txq7_bytes"   },
+	{ "txq8_packets" },
+	{ "txq8_bytes"   },
+	{ "txq9_packets" },
+	{ "txq9_bytes"   },
+	{ "txq10_packets" },
+	{ "txq10_bytes"   },
+	{ "txq11_packets" },
+	{ "txq11_bytes"   },
+	{ "txq12_packets" },
+	{ "txq12_bytes"   },
+	{ "txq13_packets" },
+	{ "txq13_bytes"   },
+	{ "txq14_packets" },
+	{ "txq14_bytes"   },
+	{ "txq15_packets" },
+	{ "txq15_bytes"   },
+};
+
+static struct axienet_stat axienet_get_rx_strings_stats[] = {
+	{ "rxq0_packets" },
+	{ "rxq0_bytes"   },
+	{ "rxq1_packets" },
+	{ "rxq1_bytes"   },
+	{ "rxq2_packets" },
+	{ "rxq2_bytes"   },
+	{ "rxq3_packets" },
+	{ "rxq3_bytes"   },
+	{ "rxq4_packets" },
+	{ "rxq4_bytes"   },
+	{ "rxq5_packets" },
+	{ "rxq5_bytes"   },
+	{ "rxq6_packets" },
+	{ "rxq6_bytes"   },
+	{ "rxq7_packets" },
+	{ "rxq7_bytes"   },
+	{ "rxq8_packets" },
+	{ "rxq8_bytes"   },
+	{ "rxq9_packets" },
+	{ "rxq9_bytes"   },
+	{ "rxq10_packets" },
+	{ "rxq10_bytes"   },
+	{ "rxq11_packets" },
+	{ "rxq11_bytes"   },
+	{ "rxq12_packets" },
+	{ "rxq12_bytes"   },
+	{ "rxq13_packets" },
+	{ "rxq13_bytes"   },
+	{ "rxq14_packets" },
+	{ "rxq14_bytes"   },
+	{ "rxq15_packets" },
+	{ "rxq15_bytes"   },
+};
+
+/**
+ * axienet_mcdma_tx_bd_free - Release MCDMA Tx buffer descriptor rings
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * This function is used to release the descriptors allocated in
+ * axienet_mcdma_tx_q_init.
+ */
+void __maybe_unused axienet_mcdma_tx_bd_free(struct net_device *ndev,
+					     struct axienet_dma_q *q)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (q->txq_bd_v) {
+		dma_free_coherent(ndev->dev.parent,
+				  sizeof(*q->txq_bd_v) * lp->tx_bd_num,
+				  q->txq_bd_v,
+				  q->tx_bd_p);
+	}
+	if (q->tx_bufs) {
+		dma_free_coherent(ndev->dev.parent,
+				  XAE_MAX_PKT_LEN * lp->tx_bd_num,
+				  q->tx_bufs,
+				  q->tx_bufs_dma);
+	}
+}
+
+/**
+ * axienet_mcdma_rx_bd_free - Release MCDMA Rx buffer descriptor rings
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * This function is used to release the descriptors allocated in
+ * axienet_mcdma_rx_q_init.
+ */
+void __maybe_unused axienet_mcdma_rx_bd_free(struct net_device *ndev,
+					     struct axienet_dma_q *q)
+{
+	int i;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (!q->rxq_bd_v)
+		return;
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		if (q->rxq_bd_v[i].phys)
+			dma_unmap_single(ndev->dev.parent, q->rxq_bd_v[i].phys,
+					 lp->max_frm_size, DMA_FROM_DEVICE);
+		dev_kfree_skb((struct sk_buff *)
+			      (q->rxq_bd_v[i].sw_id_offset));
+	}
+
+	dma_free_coherent(ndev->dev.parent,
+			  sizeof(*q->rxq_bd_v) * lp->rx_bd_num,
+			  q->rxq_bd_v,
+			  q->rx_bd_p);
+	q->rxq_bd_v = NULL;
+}
+
+/**
+ * axienet_mcdma_tx_q_init - Setup buffer descriptor rings for individual Axi
+ * MCDMA-Tx
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_bd_init
+ */
+int __maybe_unused axienet_mcdma_tx_q_init(struct net_device *ndev,
+					   struct axienet_dma_q *q)
+{
+	u32 cr, chan_en;
+	int i;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	q->tx_bd_ci = 0;
+	q->tx_bd_tail = 0;
+
+	q->txq_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					 sizeof(*q->txq_bd_v) * lp->tx_bd_num,
+					 &q->tx_bd_p, GFP_KERNEL);
+	if (!q->txq_bd_v)
+		goto out;
+
+	if (!q->eth_hasdre) {
+		q->tx_bufs = dma_alloc_coherent(ndev->dev.parent,
+						XAE_MAX_PKT_LEN * lp->tx_bd_num,
+						&q->tx_bufs_dma,
+						GFP_KERNEL);
+		if (!q->tx_bufs)
+			goto out;
+
+		for (i = 0; i < lp->tx_bd_num; i++)
+			q->tx_buf[i] = &q->tx_bufs[i * XAE_MAX_PKT_LEN];
+	}
+
+	for (i = 0; i < lp->tx_bd_num; i++) {
+		q->txq_bd_v[i].next = q->tx_bd_p +
+				      sizeof(*q->txq_bd_v) *
+				      ((i + 1) % lp->tx_bd_num);
+	}
+
+	/* Start updating the Tx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	/* Update the interrupt coalesce count */
+	cr = (((cr & ~XMCDMA_COALESCE_MASK)) |
+	      ((lp->coalesce_count_tx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = (((cr & ~XMCDMA_DELAY_MASK)) |
+	      (XAXIDMA_DFT_TX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Tx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+	/* Write to the RS (Run-stop) bit in the Tx channel control register.
+	 * Tx channel is now ready to run. But only after we write to the
+	 * tail pointer register that the Tx channel will start transmitting.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id),
+			  q->tx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id),
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET, chan_en);
+
+	return 0;
+out:
+	for_each_tx_dma_queue(lp, i) {
+		axienet_mcdma_tx_bd_free(ndev, lp->dq[i]);
+	}
+	return -ENOMEM;
+}
+
+/**
+ * axienet_mcdma_rx_q_init - Setup buffer descriptor rings for individual Axi
+ * MCDMA-Rx
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_bd_init
+ */
+int __maybe_unused axienet_mcdma_rx_q_init(struct net_device *ndev,
+					   struct axienet_dma_q *q)
+{
+	u32 cr, chan_en;
+	int i;
+	struct sk_buff *skb;
+	struct axienet_local *lp = netdev_priv(ndev);
+	dma_addr_t mapping;
+
+	q->rx_bd_ci = 0;
+	q->rx_offset = XMCDMA_CHAN_RX_OFFSET;
+
+	q->rxq_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					 sizeof(*q->rxq_bd_v) * lp->rx_bd_num,
+					 &q->rx_bd_p, GFP_KERNEL);
+	if (!q->rxq_bd_v)
+		goto out;
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		q->rxq_bd_v[i].next = q->rx_bd_p +
+				      sizeof(*q->rxq_bd_v) *
+				      ((i + 1) % lp->rx_bd_num);
+
+		skb = netdev_alloc_skb(ndev, lp->max_frm_size);
+		if (!skb)
+			goto out;
+
+		/* Ensure that the skb is completely updated
+		 * prio to mapping the DMA
+		 */
+		wmb();
+
+		q->rxq_bd_v[i].sw_id_offset = (phys_addr_t)skb;
+		mapping = dma_map_single(ndev->dev.parent,
+					 skb->data,
+					 lp->max_frm_size,
+					 DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, mapping))) {
+			dev_err(&ndev->dev, "mcdma map error\n");
+			goto out;
+		}
+
+		q->rxq_bd_v[i].phys = mapping;
+		q->rxq_bd_v[i].cntrl = lp->max_frm_size;
+	}
+
+	/* Start updating the Rx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			      q->rx_offset);
+	/* Update the interrupt coalesce count */
+	cr = ((cr & ~XMCDMA_COALESCE_MASK) |
+	      ((lp->coalesce_count_rx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = ((cr & ~XMCDMA_DELAY_MASK) |
+	      (XAXIDMA_DFT_RX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Rx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			  q->rx_offset, cr);
+
+	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
+	 * halted state. This will make the Rx side ready for reception.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET +  q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET +  q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) + q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p + (sizeof(*q->rxq_bd_v) *
+			    (lp->rx_bd_num - 1)));
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET + q->rx_offset);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET + q->rx_offset, chan_en);
+
+	return 0;
+
+out:
+	for_each_rx_dma_queue(lp, i) {
+		axienet_mcdma_rx_bd_free(ndev, lp->dq[i]);
+	}
+	return -ENOMEM;
+}
+
+static inline int get_mcdma_tx_q(struct axienet_local *lp, u32 chan_id)
+{
+	int i;
+
+	for_each_tx_dma_queue(lp, i) {
+		if (chan_id == lp->chan_num[i])
+			return lp->qnum[i];
+	}
+
+	return -ENODEV;
+}
+
+static inline int get_mcdma_rx_q(struct axienet_local *lp, u32 chan_id)
+{
+	int i;
+
+	for_each_rx_dma_queue(lp, i) {
+		if (chan_id == lp->chan_num[i])
+			return lp->qnum[i];
+	}
+
+	return -ENODEV;
+}
+
+static inline int map_dma_q_txirq(int irq, struct axienet_local *lp)
+{
+	int i, chan_sermask;
+	u16 chan_id = 1;
+	struct axienet_dma_q *q = lp->dq[0];
+
+	chan_sermask = axienet_dma_in32(q, XMCDMA_TXINT_SER_OFFSET);
+
+	for (i = 1, chan_id = 1; i != 0 && i <= chan_sermask;
+	     i <<= 1, chan_id++) {
+		if (chan_sermask & i)
+			return chan_id;
+	}
+
+	return -ENODEV;
+}
+
+irqreturn_t __maybe_unused axienet_mcdma_tx_irq(int irq, void *_ndev)
+{
+	u32 cr;
+	unsigned int status;
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i, j = map_dma_q_txirq(irq, lp);
+	struct axienet_dma_q *q;
+
+	if (j < 0)
+		return IRQ_NONE;
+
+	i = get_mcdma_tx_q(lp, j);
+	q = lp->dq[i];
+
+	status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id));
+	if (status & (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK)) {
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id), status);
+		axienet_start_xmit_done(lp->ndev, q);
+		goto out;
+	}
+	if (!(status & XMCDMA_IRQ_ALL_MASK))
+		return IRQ_NONE;
+	if (status & XMCDMA_IRQ_ERR_MASK) {
+		dev_err(&ndev->dev, "DMA Tx error 0x%x\n", status);
+		dev_err(&ndev->dev, "Current BD is at: %pa\n",
+			&q->txq_bd_v[q->tx_bd_ci].phys);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* Finally write to the Tx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      q->rx_offset);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* write to the Rx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  q->rx_offset, cr);
+
+		tasklet_schedule(&lp->dma_err_tasklet[i]);
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset, status);
+	}
+out:
+	return IRQ_HANDLED;
+}
+
+static inline int map_dma_q_rxirq(int irq, struct axienet_local *lp)
+{
+	int i, chan_sermask;
+	u16 chan_id = 1;
+	struct axienet_dma_q *q = lp->dq[0];
+
+	chan_sermask = axienet_dma_in32(q, XMCDMA_RXINT_SER_OFFSET +
+					q->rx_offset);
+
+	for (i = 1, chan_id = 1; i != 0 && i <= chan_sermask;
+		i <<= 1, chan_id++) {
+		if (chan_sermask & i)
+			return chan_id;
+	}
+
+	return -ENODEV;
+}
+
+irqreturn_t __maybe_unused axienet_mcdma_rx_irq(int irq, void *_ndev)
+{
+	u32 cr;
+	unsigned int status;
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i, j = map_dma_q_rxirq(irq, lp);
+	struct axienet_dma_q *q;
+
+	if (j < 0)
+		return IRQ_NONE;
+
+	i = get_mcdma_rx_q(lp, j);
+	q = lp->dq[i];
+
+	status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset);
+	if (status & (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK)) {
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      q->rx_offset);
+		cr &= ~(XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK);
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  q->rx_offset, cr);
+		napi_schedule(&lp->napi[i]);
+	}
+
+	if (!(status & XMCDMA_IRQ_ALL_MASK))
+		return IRQ_NONE;
+
+	if (status & XMCDMA_IRQ_ERR_MASK) {
+		dev_err(&ndev->dev, "DMA Rx error 0x%x\n", status);
+		dev_err(&ndev->dev, "Current BD is at: %pa\n",
+			&q->rxq_bd_v[q->rx_bd_ci].phys);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* Finally write to the Tx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      q->rx_offset);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* write to the Rx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  q->rx_offset, cr);
+
+		tasklet_schedule(&lp->dma_err_tasklet[i]);
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset, status);
+	}
+
+	return IRQ_HANDLED;
+}
+
+void axienet_strings(struct net_device *ndev, u32 sset, u8 *data)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	int i = AXIENET_ETHTOOLS_SSTATS_LEN, j, k = 0;
+
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_tx_queues)
+			break;
+		q = lp->dq[j];
+		if (i % 2 == 0)
+			k = (q->chan_id - 1) * 2;
+		if (sset == ETH_SS_STATS)
+			memcpy(data + i * ETH_GSTRING_LEN,
+			       axienet_get_tx_strings_stats[k].name,
+			       ETH_GSTRING_LEN);
+		++i;
+		k++;
+		if (i % 2 == 0)
+			++j;
+	}
+	k = 0;
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_RX_SSTATS_LEN(lp) +
+			AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_rx_queues)
+			break;
+		q = lp->dq[j];
+		if (i % 2 == 0)
+			k = (q->chan_id - 1) * 2;
+		if (sset == ETH_SS_STATS)
+			memcpy(data + i * ETH_GSTRING_LEN,
+			       axienet_get_rx_strings_stats[k].name,
+			       ETH_GSTRING_LEN);
+		++i;
+		k++;
+		if (i % 2 == 0)
+			++j;
+	}
+}
+
+int axienet_sset_count(struct net_device *ndev, int sset)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	switch (sset) {
+	case ETH_SS_STATS:
+		return (AXIENET_TX_SSTATS_LEN(lp) + AXIENET_RX_SSTATS_LEN(lp) +
+			AXIENET_ETHTOOLS_SSTATS_LEN);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+void axienet_get_stats(struct net_device *ndev,
+		       struct ethtool_stats *stats,
+		       u64 *data)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	unsigned int i = AXIENET_ETHTOOLS_SSTATS_LEN, j;
+
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_tx_queues)
+			break;
+
+		q = lp->dq[j];
+		data[i++] = q->tx_packets;
+		data[i++] = q->tx_bytes;
+		++j;
+	}
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_RX_SSTATS_LEN(lp) +
+			AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_rx_queues)
+			break;
+
+		q = lp->dq[j];
+		data[i++] = q->rx_packets;
+		data[i++] = q->rx_bytes;
+		++j;
+	}
+}
+
+/**
+ * axienet_mcdma_err_handler - Tasklet handler for Axi MCDMA Error
+ * @data:	Data passed
+ *
+ * Resets the Axi MCDMA and Axi Ethernet devices, and reconfigures the
+ * Tx/Rx BDs.
+ */
+void __maybe_unused axienet_mcdma_err_handler(unsigned long data)
+{
+	u32 axienet_status;
+	u32 cr, i, chan_en;
+	struct axienet_dma_q *q = (struct axienet_dma_q *)data;
+	struct axienet_local *lp = q->lp;
+	struct net_device *ndev = lp->ndev;
+	struct aximcdma_bd *cur_p;
+
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+	__axienet_device_reset(q);
+
+	for (i = 0; i < lp->tx_bd_num; i++) {
+		cur_p = &q->txq_bd_v[i];
+		if (cur_p->phys)
+			dma_unmap_single(ndev->dev.parent, cur_p->phys,
+					 (cur_p->cntrl &
+					  XAXIDMA_BD_CTRL_LENGTH_MASK),
+					 DMA_TO_DEVICE);
+		if (cur_p->tx_skb)
+			dev_kfree_skb_irq((struct sk_buff *)cur_p->tx_skb);
+		cur_p->phys = 0;
+		cur_p->cntrl = 0;
+		cur_p->status = 0;
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app3 = 0;
+		cur_p->app4 = 0;
+		cur_p->sw_id_offset = 0;
+		cur_p->tx_skb = 0;
+	}
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		cur_p = &q->rxq_bd_v[i];
+		cur_p->status = 0;
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app3 = 0;
+		cur_p->app4 = 0;
+	}
+
+	q->tx_bd_ci = 0;
+	q->tx_bd_tail = 0;
+	q->rx_bd_ci = 0;
+
+	/* Start updating the Rx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			      q->rx_offset);
+	/* Update the interrupt coalesce count */
+	cr = ((cr & ~XMCDMA_COALESCE_MASK) |
+	      ((lp->coalesce_count_rx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = ((cr & ~XMCDMA_DELAY_MASK) |
+	      (XAXIDMA_DFT_RX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Rx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			  q->rx_offset, cr);
+
+	/* Start updating the Tx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	/* Update the interrupt coalesce count */
+	cr = (((cr & ~XMCDMA_COALESCE_MASK)) |
+	      ((lp->coalesce_count_tx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = (((cr & ~XMCDMA_DELAY_MASK)) |
+	      (XAXIDMA_DFT_TX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Tx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
+	 * halted state. This will make the Rx side ready for reception.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET +  q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET +  q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) + q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p + (sizeof(*q->rxq_bd_v) *
+			    (lp->rx_bd_num - 1)));
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET + q->rx_offset);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET + q->rx_offset, chan_en);
+
+	/* Write to the RS (Run-stop) bit in the Tx channel control register.
+	 * Tx channel is now ready to run. But only after we write to the
+	 * tail pointer register that the Tx channel will start transmitting.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id),
+			  q->tx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id),
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET, chan_en);
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC) {
+		axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+		axienet_status &= ~XAE_RCW1_RX_MASK;
+		axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
+	}
+
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf) {
+		axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+		if (axienet_status & XAE_INT_RXRJECT_MASK)
+			axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+
+#ifdef CONFIG_XILINX_AXI_EMAC_HWTSTAMP
+	if (lp->axienet_config->mactype == XAXIENET_10G_25G ||
+	    lp->axienet_config->mactype == XAXIENET_MRMAC) {
+		axienet_rxts_iow(lp, XAXIFIFO_TXTS_RDFR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+		axienet_rxts_iow(lp, XAXIFIFO_TXTS_SRR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+		axienet_txts_iow(lp, XAXIFIFO_TXTS_RDFR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+		axienet_txts_iow(lp, XAXIFIFO_TXTS_SRR,
+				 XAXIFIFO_TXTS_RESET_MASK);
+	}
+#endif
+
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+	axienet_set_mac_address(ndev, NULL);
+	axienet_set_multicast_list(ndev);
+	lp->axienet_config->setoptions(ndev, lp->options);
+}
+
+int __maybe_unused axienet_mcdma_tx_probe(struct platform_device *pdev,
+					  struct device_node *np,
+					  struct axienet_local *lp)
+{
+	int i;
+	char dma_name[24];
+
+	for_each_tx_dma_queue(lp, i) {
+		struct axienet_dma_q *q;
+
+		q = lp->dq[i];
+
+		q->dma_regs = lp->mcdma_regs;
+		snprintf(dma_name, sizeof(dma_name), "mm2s_ch%d_introut",
+			 q->chan_id);
+		q->tx_irq = platform_get_irq_byname(pdev, dma_name);
+		q->eth_hasdre = of_property_read_bool(np,
+						      "xlnx,include-dre");
+		spin_lock_init(&q->tx_lock);
+	}
+	of_node_put(np);
+
+	return 0;
+}
+
+int __maybe_unused axienet_mcdma_rx_probe(struct platform_device *pdev,
+					  struct axienet_local *lp,
+					  struct net_device *ndev)
+{
+	int i;
+	char dma_name[24];
+
+	for_each_rx_dma_queue(lp, i) {
+		struct axienet_dma_q *q;
+
+		q = lp->dq[i];
+
+		q->dma_regs = lp->mcdma_regs;
+		snprintf(dma_name, sizeof(dma_name), "s2mm_ch%d_introut",
+			 q->chan_id);
+		q->rx_irq = platform_get_irq_byname(pdev, dma_name);
+
+		spin_lock_init(&q->rx_lock);
+
+		netif_napi_add(ndev, &lp->napi[i], xaxienet_rx_poll,
+			       XAXIENET_NAPI_WEIGHT);
+	}
+
+	return 0;
+}
+
+static ssize_t rxch_obs1_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS1_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 1 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs2_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS2_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 2 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs3_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS3_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 3 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs4_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS4_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 4 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs5_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS5_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 5 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs6_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS6_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 6 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs1_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS1_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 1 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t txch_obs2_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS2_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 2 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs3_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS3_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 3 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs4_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS4_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 4 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs5_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS5_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 5 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs6_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS6_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 6 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t chan_weight_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	return sprintf(buf, "chan_id is %d and weight is %d\n",
+		       lp->chan_id, lp->weight);
+}
+
+static ssize_t chan_weight_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	int ret;
+	u16 flags, chan_id;
+	u32 val;
+
+	ret = kstrtou16(buf, 16, &flags);
+	if (ret)
+		return ret;
+
+	lp->chan_id = (flags & 0xF0) >> 4;
+	lp->weight = flags & 0x0F;
+
+	if (lp->chan_id < 8)
+		val = axienet_dma_in32(q, XMCDMA_TXWEIGHT0_OFFSET);
+	else
+		val = axienet_dma_in32(q, XMCDMA_TXWEIGHT1_OFFSET);
+
+	if (lp->chan_id > 7)
+		chan_id = lp->chan_id - 8;
+	else
+		chan_id = lp->chan_id;
+
+	val &= ~XMCDMA_TXWEIGHT_CH_MASK(chan_id);
+	val |= lp->weight << XMCDMA_TXWEIGHT_CH_SHIFT(chan_id);
+
+	if (lp->chan_id < 8)
+		axienet_dma_out32(q, XMCDMA_TXWEIGHT0_OFFSET, val);
+	else
+		axienet_dma_out32(q, XMCDMA_TXWEIGHT1_OFFSET, val);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(chan_weight);
+static DEVICE_ATTR_RO(rxch_obs1);
+static DEVICE_ATTR_RO(rxch_obs2);
+static DEVICE_ATTR_RO(rxch_obs3);
+static DEVICE_ATTR_RO(rxch_obs4);
+static DEVICE_ATTR_RO(rxch_obs5);
+static DEVICE_ATTR_RO(rxch_obs6);
+static DEVICE_ATTR_RO(txch_obs1);
+static DEVICE_ATTR_RO(txch_obs2);
+static DEVICE_ATTR_RO(txch_obs3);
+static DEVICE_ATTR_RO(txch_obs4);
+static DEVICE_ATTR_RO(txch_obs5);
+static DEVICE_ATTR_RO(txch_obs6);
+static const struct attribute *mcdma_attrs[] = {
+	&dev_attr_chan_weight.attr,
+	&dev_attr_rxch_obs1.attr,
+	&dev_attr_rxch_obs2.attr,
+	&dev_attr_rxch_obs3.attr,
+	&dev_attr_rxch_obs4.attr,
+	&dev_attr_rxch_obs5.attr,
+	&dev_attr_rxch_obs6.attr,
+	&dev_attr_txch_obs1.attr,
+	&dev_attr_txch_obs2.attr,
+	&dev_attr_txch_obs3.attr,
+	&dev_attr_txch_obs4.attr,
+	&dev_attr_txch_obs5.attr,
+	&dev_attr_txch_obs6.attr,
+	NULL,
+};
+
+static const struct attribute_group mcdma_attributes = {
+	.attrs = (struct attribute **)mcdma_attrs,
+};
+
+int axeinet_mcdma_create_sysfs(struct kobject *kobj)
+{
+	return sysfs_create_group(kobj, &mcdma_attributes);
+}
+
+void axeinet_mcdma_remove_sysfs(struct kobject *kobj)
+{
+	sysfs_remove_group(kobj, &mcdma_attributes);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
@@ -21,7 +21,7 @@
 #define DEFAULT_HOST_CLOCK	150000000 /* 150 MHz */
 
 /* Wait till MDIO interface is ready to accept a new transaction.*/
-static int axienet_mdio_wait_until_ready(struct axienet_local *lp)
+int axienet_mdio_wait_until_ready(struct axienet_local *lp)
 {
 	u32 val;
 
@@ -89,8 +89,8 @@
 
 	rc = axienet_ior(lp, XAE_MDIO_MRD_OFFSET) & 0x0000FFFF;
 
-	dev_dbg(lp->dev, "axienet_mdio_read(phy_id=%i, reg=%x) == %x\n",
-		phy_id, reg, rc);
+	dev_dbg(lp->dev, "%s (phy_id=%i, reg=%x) == %x\n",
+		__func__, phy_id, reg, rc);
 
 	axienet_mdio_mdc_disable(lp);
 	return rc;
@@ -106,7 +106,7 @@
  * Return:	0 on success, -ETIMEDOUT on a timeout
  *
  * Writes the value to the requested register by first writing the value
- * into MWD register. The the MCR register is then appropriately setup
+ * into MWD register. The MCR register is then appropriately setup
  * to finish the write operation.
  */
 static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg,
@@ -115,8 +115,8 @@
 	int ret;
 	struct axienet_local *lp = bus->priv;
 
-	dev_dbg(lp->dev, "axienet_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
-		phy_id, reg, val);
+	dev_dbg(lp->dev, "%s (phy_id=%i, reg=%x, val=%x)\n",
+		__func__, phy_id, reg, val);
 
 	axienet_mdio_mdc_enable(lp);
 
@@ -126,7 +126,7 @@
 		return ret;
 	}
 
-	axienet_iow(lp, XAE_MDIO_MWD_OFFSET, (u32) val);
+	axienet_iow(lp, XAE_MDIO_MWD_OFFSET, (u32)val);
 	axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
 		    (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
 		      XAE_MDIO_MCR_PHYAD_MASK) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xilinx/xilinx_emaclite.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xilinx/xilinx_emaclite.c
@@ -1,11 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Xilinx EmacLite Linux driver for the Xilinx Ethernet MAC Lite device.
+/* Xilinx EmacLite Linux driver for the Xilinx Ethernet MAC Lite device.
  *
  * This is a new flat driver which is based on the original emac_lite
  * driver from John Williams <john.williams@xilinx.com>.
  *
- * 2007 - 2013 (c) Xilinx, Inc.
+ * Copyright (c) 2007 - 2013 Xilinx, Inc.
  */
 
 #include <linux/module.h>
@@ -91,13 +90,7 @@
 #define XEL_ARP_PACKET_SIZE		28	/* Max ARP packet size */
 #define XEL_HEADER_IP_LENGTH_OFFSET	16	/* IP Length Offset */
 
-
-
 #define TX_TIMEOUT		(60 * HZ)	/* Tx timeout is 60 seconds. */
-#define ALIGNMENT		4
-
-/* BUFFER_ALIGN(adr) calculates the number of bytes to the next alignment. */
-#define BUFFER_ALIGN(adr) ((ALIGNMENT - ((uintptr_t)adr)) % ALIGNMENT)
 
 #ifdef __BIG_ENDIAN
 #define xemaclite_readl		ioread32be
@@ -115,7 +108,7 @@
  * @next_tx_buf_to_use:	next Tx buffer to write to
  * @next_rx_buf_to_use:	next Rx buffer to read from
  * @base_addr:		base address of the Emaclite device
- * @reset_lock:		lock used for synchronization
+ * @reset_lock:		lock to serialize xmit and tx_timeout execution
  * @deferred_skb:	holds an skb (for transmission at a later time) when the
  *			Tx buffer is not free
  * @phy_dev:		pointer to the PHY device
@@ -124,7 +117,6 @@
  * @last_link:		last link status
  */
 struct net_local {
-
 	struct net_device *ndev;
 
 	bool tx_ping_pong;
@@ -133,7 +125,7 @@
 	u32 next_rx_buf_to_use;
 	void __iomem *base_addr;
 
-	spinlock_t reset_lock;
+	spinlock_t reset_lock; /* serialize xmit and tx_timeout execution */
 	struct sk_buff *deferred_skb;
 
 	struct phy_device *phy_dev;
@@ -144,7 +136,6 @@
 	int last_link;
 };
 
-
 /*************************/
 /* EmacLite driver calls */
 /*************************/
@@ -206,12 +197,13 @@
  * This function writes data from a 16-bit aligned buffer to a 32-bit aligned
  * address in the EmacLite device.
  */
-static void xemaclite_aligned_write(void *src_ptr, u32 *dest_ptr,
+static void xemaclite_aligned_write(const void *src_ptr, u32 *dest_ptr,
 				    unsigned length)
 {
+	const u16 *from_u16_ptr;
 	u32 align_buffer;
 	u32 *to_u32_ptr;
-	u16 *from_u16_ptr, *to_u16_ptr;
+	u16 *to_u16_ptr;
 
 	to_u32_ptr = dest_ptr;
 	from_u16_ptr = src_ptr;
@@ -264,7 +256,7 @@
  * to a 16-bit aligned buffer.
  */
 static void xemaclite_aligned_read(u32 *src_ptr, u8 *dest_ptr,
-				   unsigned length)
+				   unsigned int length)
 {
 	u16 *to_u16_ptr, *from_u16_ptr;
 	u32 *from_u32_ptr;
@@ -329,7 +321,6 @@
 	reg_data = xemaclite_readl(addr + XEL_TSR_OFFSET);
 	if ((reg_data & (XEL_TSR_XMIT_BUSY_MASK |
 	     XEL_TSR_XMIT_ACTIVE_MASK)) == 0) {
-
 		/* Switch to next buffer if configured */
 		if (drvdata->tx_ping_pong != 0)
 			drvdata->next_tx_buf_to_use ^= XEL_BUFFER_OFFSET;
@@ -345,8 +336,9 @@
 		if ((reg_data & (XEL_TSR_XMIT_BUSY_MASK |
 		     XEL_TSR_XMIT_ACTIVE_MASK)) != 0)
 			return -1; /* Buffers were full, return failure */
-	} else
+	} else {
 		return -1; /* Buffer was full, return failure */
+	}
 
 	/* Write the frame to the buffer */
 	xemaclite_aligned_write(data, (u32 __force *)addr, byte_count);
@@ -422,7 +414,6 @@
 	 * or an IP packet or an ARP packet
 	 */
 	if (proto_type > ETH_DATA_LEN) {
-
 		if (proto_type == ETH_P_IP) {
 			length = ((ntohl(xemaclite_readl(addr +
 					XEL_HEADER_IP_LENGTH_OFFSET +
@@ -432,23 +423,25 @@
 			length = min_t(u16, length, ETH_DATA_LEN);
 			length += ETH_HLEN + ETH_FCS_LEN;
 
-		} else if (proto_type == ETH_P_ARP)
+		} else if (proto_type == ETH_P_ARP) {
 			length = XEL_ARP_PACKET_SIZE + ETH_HLEN + ETH_FCS_LEN;
-		else
+		} else {
 			/* Field contains type other than IP or ARP, use max
 			 * frame size and let user parse it
 			 */
 			length = ETH_FRAME_LEN + ETH_FCS_LEN;
-	} else
+		}
+	} else {
 		/* Use the length in the frame, plus the header and trailer */
 		length = proto_type + ETH_HLEN + ETH_FCS_LEN;
+	}
 
 	if (WARN_ON(length > maxlen))
 		length = maxlen;
 
 	/* Read from the EmacLite device */
 	xemaclite_aligned_read((u32 __force *)(addr + XEL_RXBUFF_OFFSET),
-				data, length);
+			       data, length);
 
 	/* Acknowledge the frame */
 	reg_data = xemaclite_readl(addr + XEL_RSR_OFFSET);
@@ -470,7 +463,7 @@
  * buffers (if configured).
  */
 static void xemaclite_update_address(struct net_local *drvdata,
-				     u8 *address_ptr)
+				     const u8 *address_ptr)
 {
 	void __iomem *addr;
 	u32 reg_data;
@@ -543,7 +536,7 @@
 	xemaclite_enable_interrupts(lp);
 
 	if (lp->deferred_skb) {
-		dev_kfree_skb(lp->deferred_skb);
+		dev_kfree_skb_irq(lp->deferred_skb);
 		lp->deferred_skb = NULL;
 		dev->stats.tx_errors++;
 	}
@@ -598,11 +591,10 @@
 {
 	struct net_local *lp = netdev_priv(dev);
 	struct sk_buff *skb;
-	unsigned int align;
 	u32 len;
 
 	len = ETH_FRAME_LEN + ETH_FCS_LEN;
-	skb = netdev_alloc_skb(dev, len + ALIGNMENT);
+	skb = netdev_alloc_skb(dev, len + NET_IP_ALIGN);
 	if (!skb) {
 		/* Couldn't get memory. */
 		dev->stats.rx_dropped++;
@@ -610,16 +602,7 @@
 		return;
 	}
 
-	/* A new skb should have the data halfword aligned, but this code is
-	 * here just in case that isn't true. Calculate how many
-	 * bytes we should reserve to get the data to start on a word
-	 * boundary
-	 */
-	align = BUFFER_ALIGN(skb->data);
-	if (align)
-		skb_reserve(skb, align);
-
-	skb_reserve(skb, 2);
+	skb_reserve(skb, NET_IP_ALIGN);
 
 	len = xemaclite_recv_data(lp, (u8 *)skb->data, len);
 
@@ -670,8 +653,7 @@
 	/* Check if the Transmission for the first buffer is completed */
 	tx_status = xemaclite_readl(base_addr + XEL_TSR_OFFSET);
 	if (((tx_status & XEL_TSR_XMIT_BUSY_MASK) == 0) &&
-		(tx_status & XEL_TSR_XMIT_ACTIVE_MASK) != 0) {
-
+	    (tx_status & XEL_TSR_XMIT_ACTIVE_MASK) != 0) {
 		tx_status &= ~XEL_TSR_XMIT_ACTIVE_MASK;
 		xemaclite_writel(tx_status, base_addr + XEL_TSR_OFFSET);
 
@@ -681,8 +663,7 @@
 	/* Check if the Transmission for the second buffer is completed */
 	tx_status = xemaclite_readl(base_addr + XEL_BUFFER_OFFSET + XEL_TSR_OFFSET);
 	if (((tx_status & XEL_TSR_XMIT_BUSY_MASK) == 0) &&
-		(tx_status & XEL_TSR_XMIT_ACTIVE_MASK) != 0) {
-
+	    (tx_status & XEL_TSR_XMIT_ACTIVE_MASK) != 0) {
 		tx_status &= ~XEL_TSR_XMIT_ACTIVE_MASK;
 		xemaclite_writel(tx_status, base_addr + XEL_BUFFER_OFFSET +
 				 XEL_TSR_OFFSET);
@@ -822,10 +803,10 @@
 static int xemaclite_mdio_setup(struct net_local *lp, struct device *dev)
 {
 	struct mii_bus *bus;
-	int rc;
 	struct resource res;
 	struct device_node *np = of_get_parent(lp->phy_node);
 	struct device_node *npp;
+	int rc, ret;
 
 	/* Don't register the MDIO bus if the phy_node or its parent node
 	 * can't be found.
@@ -836,15 +817,23 @@
 	}
 	npp = of_get_parent(np);
 
-	of_address_to_resource(npp, 0, &res);
+	ret = of_address_to_resource(npp, 0, &res);
+	if (ret) {
+		dev_err(dev, "%s resource error!\n",
+			dev->of_node->full_name);
+		of_node_put(lp->phy_node);
+		return ret;
+	}
 	if (lp->ndev->mem_start != res.start) {
 		struct phy_device *phydev;
+
 		phydev = of_phy_find_device(lp->phy_node);
 		if (!phydev)
 			dev_info(dev,
 				 "MDIO of the phy is not registered yet\n");
 		else
 			put_device(&phydev->mdio.dev);
+		of_node_put(np);
 		return 0;
 	}
 
@@ -857,6 +846,7 @@
 	bus = mdiobus_alloc();
 	if (!bus) {
 		dev_err(dev, "Failed to allocate mdiobus\n");
+		of_node_put(np);
 		return -ENOMEM;
 	}
 
@@ -869,6 +859,7 @@
 	bus->parent = dev;
 
 	rc = of_mdiobus_register(bus, np);
+	of_node_put(np);
 	if (rc) {
 		dev_err(dev, "Failed to register mdio bus.\n");
 		goto err_register;
@@ -925,8 +916,6 @@
 	xemaclite_disable_interrupts(lp);
 
 	if (lp->phy_node) {
-		u32 bmcr;
-
 		lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node,
 					     xemaclite_adjust_link, 0,
 					     PHY_INTERFACE_MODE_MII);
@@ -937,19 +926,6 @@
 
 		/* EmacLite doesn't support giga-bit speeds */
 		phy_set_max_speed(lp->phy_dev, SPEED_100);
-
-		/* Don't advertise 1000BASE-T Full/Half duplex speeds */
-		phy_write(lp->phy_dev, MII_CTRL1000, 0);
-
-		/* Advertise only 10 and 100mbps full/half duplex speeds */
-		phy_write(lp->phy_dev, MII_ADVERTISE, ADVERTISE_ALL |
-			  ADVERTISE_CSMA);
-
-		/* Restart auto negotiation */
-		bmcr = phy_read(lp->phy_dev, MII_BMCR);
-		bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
-		phy_write(lp->phy_dev, MII_BMCR, bmcr);
-
 		phy_start(lp->phy_dev);
 	}
 
@@ -1157,7 +1133,7 @@
 	lp->tx_ping_pong = get_bool(ofdev, "xlnx,tx-ping-pong");
 	lp->rx_ping_pong = get_bool(ofdev, "xlnx,rx-ping-pong");
 
-	rc = of_get_mac_address(ofdev->dev.of_node, ndev->dev_addr);
+	rc = of_get_ethdev_address(ofdev->dev.of_node, ndev);
 	if (rc) {
 		dev_warn(dev, "No MAC address found, using random\n");
 		eth_hw_addr_random(ndev);
@@ -1185,7 +1161,7 @@
 	if (rc) {
 		dev_err(dev,
 			"Cannot register network device, aborting\n");
-		goto error;
+		goto put_node;
 	}
 
 	dev_info(dev,
@@ -1193,6 +1169,8 @@
 		 (unsigned long __force)ndev->mem_start, lp->base_addr, ndev->irq);
 	return 0;
 
+put_node:
+	of_node_put(lp->phy_node);
 error:
 	free_netdev(ndev);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xircom/xirc2ps_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xircom/xirc2ps_cs.c
@@ -503,6 +503,11 @@
 xirc2ps_detach(struct pcmcia_device *link)
 {
     struct net_device *dev = link->priv;
+    struct local_info *local = netdev_priv(dev);
+
+    netif_carrier_off(dev);
+    netif_tx_disable(dev);
+    cancel_work_sync(&local->tx_timeout_task);
 
     dev_dbg(&link->dev, "detach\n");
 
@@ -1271,7 +1276,7 @@
 	unsigned int ioaddr;
 };
 
-static void set_address(struct set_address_info *sa_info, char *addr)
+static void set_address(struct set_address_info *sa_info, const char *addr)
 {
 	unsigned int ioaddr = sa_info->ioaddr;
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ethernet/xscale/ptp_ixp46x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ethernet/xscale/ptp_ixp46x.c
@@ -272,7 +272,7 @@
 	ixp_clock.master_irq = platform_get_irq(pdev, 0);
 	ixp_clock.slave_irq = platform_get_irq(pdev, 1);
 	if (IS_ERR(ixp_clock.regs) ||
-	    !ixp_clock.master_irq || !ixp_clock.slave_irq)
+	    ixp_clock.master_irq < 0 || ixp_clock.slave_irq < 0)
 		return -ENXIO;
 
 	ixp_clock.caps = ptp_ixp_caps;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/fddi/defxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/fddi/defxx.c
@@ -3831,10 +3831,24 @@
 	int status;
 
 	status = pci_register_driver(&dfx_pci_driver);
-	if (!status)
-		status = eisa_driver_register(&dfx_eisa_driver);
-	if (!status)
-		status = tc_register_driver(&dfx_tc_driver);
+	if (status)
+		goto err_pci_register;
+
+	status = eisa_driver_register(&dfx_eisa_driver);
+	if (status)
+		goto err_eisa_register;
+
+	status = tc_register_driver(&dfx_tc_driver);
+	if (status)
+		goto err_tc_register;
+
+	return 0;
+
+err_tc_register:
+	eisa_driver_unregister(&dfx_eisa_driver);
+err_eisa_register:
+	pci_unregister_driver(&dfx_pci_driver);
+err_pci_register:
 	return status;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/fjes/fjes_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/fjes/fjes_hw.c
@@ -220,21 +220,25 @@
 
 	mem_size = FJES_DEV_REQ_BUF_SIZE(hw->max_epid);
 	hw->hw_info.req_buf = kzalloc(mem_size, GFP_KERNEL);
-	if (!(hw->hw_info.req_buf))
-		return -ENOMEM;
+	if (!(hw->hw_info.req_buf)) {
+		result = -ENOMEM;
+		goto free_ep_info;
+	}
 
 	hw->hw_info.req_buf_size = mem_size;
 
 	mem_size = FJES_DEV_RES_BUF_SIZE(hw->max_epid);
 	hw->hw_info.res_buf = kzalloc(mem_size, GFP_KERNEL);
-	if (!(hw->hw_info.res_buf))
-		return -ENOMEM;
+	if (!(hw->hw_info.res_buf)) {
+		result = -ENOMEM;
+		goto free_req_buf;
+	}
 
 	hw->hw_info.res_buf_size = mem_size;
 
 	result = fjes_hw_alloc_shared_status_region(hw);
 	if (result)
-		return result;
+		goto free_res_buf;
 
 	hw->hw_info.buffer_share_bit = 0;
 	hw->hw_info.buffer_unshare_reserve_bit = 0;
@@ -245,11 +249,11 @@
 
 			result = fjes_hw_alloc_epbuf(&buf_pair->tx);
 			if (result)
-				return result;
+				goto free_epbuf;
 
 			result = fjes_hw_alloc_epbuf(&buf_pair->rx);
 			if (result)
-				return result;
+				goto free_epbuf;
 
 			spin_lock_irqsave(&hw->rx_status_lock, flags);
 			fjes_hw_setup_epbuf(&buf_pair->tx, mac,
@@ -272,6 +276,25 @@
 	fjes_hw_init_command_registers(hw, &param);
 
 	return 0;
+
+free_epbuf:
+	for (epidx = 0; epidx < hw->max_epid ; epidx++) {
+		if (epidx == hw->my_epid)
+			continue;
+		fjes_hw_free_epbuf(&hw->ep_shm_info[epidx].tx);
+		fjes_hw_free_epbuf(&hw->ep_shm_info[epidx].rx);
+	}
+	fjes_hw_free_shared_status_region(hw);
+free_res_buf:
+	kfree(hw->hw_info.res_buf);
+	hw->hw_info.res_buf = NULL;
+free_req_buf:
+	kfree(hw->hw_info.req_buf);
+	hw->hw_info.req_buf = NULL;
+free_ep_info:
+	kfree(hw->ep_shm_info);
+	hw->ep_shm_info = NULL;
+	return result;
 }
 
 static void fjes_hw_cleanup(struct fjes_hw *hw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/fjes/fjes_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/fjes/fjes_main.c
@@ -1261,6 +1261,11 @@
 	hw->hw_res.start = res->start;
 	hw->hw_res.size = resource_size(res);
 	hw->hw_res.irq = platform_get_irq(plat_dev, 0);
+	if (hw->hw_res.irq < 0) {
+		err = hw->hw_res.irq;
+		goto err_free_control_wq;
+	}
+
 	err = fjes_hw_init(&adapter->hw);
 	if (err)
 		goto err_free_control_wq;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/geneve.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/geneve.c
@@ -55,6 +55,7 @@
 	bool			use_udp6_rx_checksums;
 	bool			ttl_inherit;
 	enum ifla_geneve_df	df;
+	bool			inner_proto_inherit;
 };
 
 /* Pseudo network device */
@@ -219,7 +220,7 @@
 	struct genevehdr *gnvh = geneve_hdr(skb);
 	struct metadata_dst *tun_dst = NULL;
 	unsigned int len;
-	int err = 0;
+	int nh, err = 0;
 	void *oiph;
 
 	if (ip_tunnel_collect_metadata() || gs->collect_md) {
@@ -250,22 +251,43 @@
 		}
 	}
 
-	skb_reset_mac_header(skb);
-	skb->protocol = eth_type_trans(skb, geneve->dev);
-	skb_postpull_rcsum(skb, eth_hdr(skb), ETH_HLEN);
-
 	if (tun_dst)
 		skb_dst_set(skb, &tun_dst->dst);
 
-	/* Ignore packet loops (and multicast echo) */
-	if (ether_addr_equal(eth_hdr(skb)->h_source, geneve->dev->dev_addr)) {
-		geneve->dev->stats.rx_errors++;
-		goto drop;
+	if (gnvh->proto_type == htons(ETH_P_TEB)) {
+		skb_reset_mac_header(skb);
+		skb->protocol = eth_type_trans(skb, geneve->dev);
+		skb_postpull_rcsum(skb, eth_hdr(skb), ETH_HLEN);
+
+		/* Ignore packet loops (and multicast echo) */
+		if (ether_addr_equal(eth_hdr(skb)->h_source,
+				     geneve->dev->dev_addr)) {
+			geneve->dev->stats.rx_errors++;
+			goto drop;
+		}
+	} else {
+		skb_reset_mac_header(skb);
+		skb->dev = geneve->dev;
+		skb->pkt_type = PACKET_HOST;
 	}
 
-	oiph = skb_network_header(skb);
+	/* Save offset of outer header relative to skb->head,
+	 * because we are going to reset the network header to the inner header
+	 * and might change skb->head.
+	 */
+	nh = skb_network_header(skb) - skb->head;
+
 	skb_reset_network_header(skb);
 
+	if (!pskb_inet_may_pull(skb)) {
+		DEV_STATS_INC(geneve->dev, rx_length_errors);
+		DEV_STATS_INC(geneve->dev, rx_errors);
+		goto drop;
+	}
+
+	/* Get the outer header. */
+	oiph = skb->head + nh;
+
 	if (geneve_get_sk_family(gs) == AF_INET)
 		err = IP_ECN_decapsulate(oiph, skb);
 #if IS_ENABLED(CONFIG_IPV6)
@@ -344,6 +366,7 @@
 	struct genevehdr *geneveh;
 	struct geneve_dev *geneve;
 	struct geneve_sock *gs;
+	__be16 inner_proto;
 	int opts_len;
 
 	/* Need UDP and Geneve header to be present */
@@ -355,7 +378,11 @@
 	if (unlikely(geneveh->ver != GENEVE_VER))
 		goto drop;
 
-	if (unlikely(geneveh->proto_type != htons(ETH_P_TEB)))
+	inner_proto = geneveh->proto_type;
+
+	if (unlikely((inner_proto != htons(ETH_P_TEB) &&
+		      inner_proto != htons(ETH_P_IP) &&
+		      inner_proto != htons(ETH_P_IPV6))))
 		goto drop;
 
 	gs = rcu_dereference_sk_user_data(sk);
@@ -366,9 +393,14 @@
 	if (!geneve)
 		goto drop;
 
+	if (unlikely((!geneve->cfg.inner_proto_inherit &&
+		      inner_proto != htons(ETH_P_TEB)))) {
+		geneve->dev->stats.rx_dropped++;
+		goto drop;
+	}
+
 	opts_len = geneveh->opt_len * 4;
-	if (iptunnel_pull_header(skb, GENEVE_BASE_HLEN + opts_len,
-				 htons(ETH_P_TEB),
+	if (iptunnel_pull_header(skb, GENEVE_BASE_HLEN + opts_len, inner_proto,
 				 !net_eq(geneve->net, dev_net(geneve->dev)))) {
 		geneve->dev->stats.rx_dropped++;
 		goto drop;
@@ -516,18 +548,15 @@
 
 	type = gh->proto_type;
 
-	rcu_read_lock();
 	ptype = gro_find_receive_by_type(type);
 	if (!ptype)
-		goto out_unlock;
+		goto out;
 
 	skb_gro_pull(skb, gh_len);
 	skb_gro_postpull_rcsum(skb, gh, gh_len);
 	pp = call_gro_receive(ptype->callbacks.gro_receive, head, skb);
 	flush = 0;
 
-out_unlock:
-	rcu_read_unlock();
 out:
 	skb_gro_flush_final(skb, pp, flush);
 
@@ -547,13 +576,10 @@
 	gh_len = geneve_hlen(gh);
 	type = gh->proto_type;
 
-	rcu_read_lock();
 	ptype = gro_find_complete_by_type(type);
 	if (ptype)
 		err = ptype->callbacks.gro_complete(skb, nhoff + gh_len);
 
-	rcu_read_unlock();
-
 	skb_set_inner_mac_header(skb, nhoff + gh_len);
 
 	return err;
@@ -722,7 +748,8 @@
 }
 
 static void geneve_build_header(struct genevehdr *geneveh,
-				const struct ip_tunnel_info *info)
+				const struct ip_tunnel_info *info,
+				__be16 inner_proto)
 {
 	geneveh->ver = GENEVE_VER;
 	geneveh->opt_len = info->options_len / 4;
@@ -730,7 +757,7 @@
 	geneveh->critical = !!(info->key.tun_flags & TUNNEL_CRIT_OPT);
 	geneveh->rsvd1 = 0;
 	tunnel_id_to_vni(info->key.tun_id, geneveh->vni);
-	geneveh->proto_type = htons(ETH_P_TEB);
+	geneveh->proto_type = inner_proto;
 	geneveh->rsvd2 = 0;
 
 	if (info->key.tun_flags & TUNNEL_GENEVE_OPT)
@@ -739,10 +766,12 @@
 
 static int geneve_build_skb(struct dst_entry *dst, struct sk_buff *skb,
 			    const struct ip_tunnel_info *info,
-			    bool xnet, int ip_hdr_len)
+			    bool xnet, int ip_hdr_len,
+			    bool inner_proto_inherit)
 {
 	bool udp_sum = !!(info->key.tun_flags & TUNNEL_CSUM);
 	struct genevehdr *gnvh;
+	__be16 inner_proto;
 	int min_headroom;
 	int err;
 
@@ -760,8 +789,9 @@
 		goto free_dst;
 
 	gnvh = __skb_push(skb, sizeof(*gnvh) + info->options_len);
-	geneve_build_header(gnvh, info);
-	skb_set_inner_protocol(skb, htons(ETH_P_TEB));
+	inner_proto = inner_proto_inherit ? skb->protocol : htons(ETH_P_TEB);
+	geneve_build_header(gnvh, info, inner_proto);
+	skb_set_inner_protocol(skb, inner_proto);
 	return 0;
 
 free_dst:
@@ -774,7 +804,8 @@
 				       struct geneve_sock *gs4,
 				       struct flowi4 *fl4,
 				       const struct ip_tunnel_info *info,
-				       __be16 dport, __be16 sport)
+				       __be16 dport, __be16 sport,
+				       __u8 *full_tos)
 {
 	bool use_cache = ip_tunnel_dst_cache_usable(skb, info);
 	struct geneve_dev *geneve = netdev_priv(dev);
@@ -799,6 +830,8 @@
 		use_cache = false;
 	}
 	fl4->flowi4_tos = RT_TOS(tos);
+	if (full_tos)
+		*full_tos = tos;
 
 	dst_cache = (struct dst_cache *)&info->dst_cache;
 	if (use_cache) {
@@ -852,8 +885,7 @@
 		use_cache = false;
 	}
 
-	fl6->flowlabel = ip6_make_flowinfo(RT_TOS(prio),
-					   info->key.label);
+	fl6->flowlabel = ip6_make_flowinfo(prio, info->key.label);
 	dst_cache = (struct dst_cache *)&info->dst_cache;
 	if (use_cache) {
 		dst = dst_cache_get_ip6(dst_cache, &fl6->saddr);
@@ -882,22 +914,24 @@
 			   struct geneve_dev *geneve,
 			   const struct ip_tunnel_info *info)
 {
+	bool inner_proto_inherit = geneve->cfg.inner_proto_inherit;
 	bool xnet = !net_eq(geneve->net, dev_net(geneve->dev));
 	struct geneve_sock *gs4 = rcu_dereference(geneve->sock4);
 	const struct ip_tunnel_key *key = &info->key;
 	struct rtable *rt;
 	struct flowi4 fl4;
+	__u8 full_tos;
 	__u8 tos, ttl;
 	__be16 df = 0;
 	__be16 sport;
 	int err;
 
-	if (!pskb_inet_may_pull(skb))
+	if (!skb_vlan_inet_prepare(skb, inner_proto_inherit))
 		return -EINVAL;
 
 	sport = udp_flow_src_port(geneve->net, skb, 1, USHRT_MAX, true);
 	rt = geneve_get_v4_rt(skb, dev, gs4, &fl4, info,
-			      geneve->cfg.info.key.tp_dst, sport);
+			      geneve->cfg.info.key.tp_dst, sport, &full_tos);
 	if (IS_ERR(rt))
 		return PTR_ERR(rt);
 
@@ -941,7 +975,7 @@
 
 		df = key->tun_flags & TUNNEL_DONT_FRAGMENT ? htons(IP_DF) : 0;
 	} else {
-		tos = ip_tunnel_ecn_encap(fl4.flowi4_tos, ip_hdr(skb), skb);
+		tos = ip_tunnel_ecn_encap(full_tos, ip_hdr(skb), skb);
 		if (geneve->cfg.ttl_inherit)
 			ttl = ip_tunnel_get_ttl(ip_hdr(skb), skb);
 		else
@@ -951,7 +985,7 @@
 		if (geneve->cfg.df == GENEVE_DF_SET) {
 			df = htons(IP_DF);
 		} else if (geneve->cfg.df == GENEVE_DF_INHERIT) {
-			struct ethhdr *eth = eth_hdr(skb);
+			struct ethhdr *eth = skb_eth_hdr(skb);
 
 			if (ntohs(eth->h_proto) == ETH_P_IPV6) {
 				df = htons(IP_DF);
@@ -964,7 +998,8 @@
 		}
 	}
 
-	err = geneve_build_skb(&rt->dst, skb, info, xnet, sizeof(struct iphdr));
+	err = geneve_build_skb(&rt->dst, skb, info, xnet, sizeof(struct iphdr),
+			       inner_proto_inherit);
 	if (unlikely(err))
 		return err;
 
@@ -980,6 +1015,7 @@
 			    struct geneve_dev *geneve,
 			    const struct ip_tunnel_info *info)
 {
+	bool inner_proto_inherit = geneve->cfg.inner_proto_inherit;
 	bool xnet = !net_eq(geneve->net, dev_net(geneve->dev));
 	struct geneve_sock *gs6 = rcu_dereference(geneve->sock6);
 	const struct ip_tunnel_key *key = &info->key;
@@ -989,7 +1025,7 @@
 	__be16 sport;
 	int err;
 
-	if (!pskb_inet_may_pull(skb))
+	if (!skb_vlan_inet_prepare(skb, inner_proto_inherit))
 		return -EINVAL;
 
 	sport = udp_flow_src_port(geneve->net, skb, 1, USHRT_MAX, true);
@@ -1043,7 +1079,8 @@
 			ttl = key->ttl;
 		ttl = ttl ? : ip6_dst_hoplimit(dst);
 	}
-	err = geneve_build_skb(dst, skb, info, xnet, sizeof(struct ipv6hdr));
+	err = geneve_build_skb(dst, skb, info, xnet, sizeof(struct ipv6hdr),
+			       inner_proto_inherit);
 	if (unlikely(err))
 		return err;
 
@@ -1123,7 +1160,7 @@
 					  1, USHRT_MAX, true);
 
 		rt = geneve_get_v4_rt(skb, dev, gs4, &fl4, info,
-				      geneve->cfg.info.key.tp_dst, sport);
+				      geneve->cfg.info.key.tp_dst, sport, NULL);
 		if (IS_ERR(rt))
 			return PTR_ERR(rt);
 
@@ -1243,6 +1280,7 @@
 }
 
 static const struct nla_policy geneve_policy[IFLA_GENEVE_MAX + 1] = {
+	[IFLA_GENEVE_UNSPEC]		= { .strict_start_type = IFLA_GENEVE_INNER_PROTO_INHERIT },
 	[IFLA_GENEVE_ID]		= { .type = NLA_U32 },
 	[IFLA_GENEVE_REMOTE]		= { .len = sizeof_field(struct iphdr, daddr) },
 	[IFLA_GENEVE_REMOTE6]		= { .len = sizeof(struct in6_addr) },
@@ -1256,6 +1294,7 @@
 	[IFLA_GENEVE_UDP_ZERO_CSUM6_RX]	= { .type = NLA_U8 },
 	[IFLA_GENEVE_TTL_INHERIT]	= { .type = NLA_U8 },
 	[IFLA_GENEVE_DF]		= { .type = NLA_U8 },
+	[IFLA_GENEVE_INNER_PROTO_INHERIT]	= { .type = NLA_FLAG },
 };
 
 static int geneve_validate(struct nlattr *tb[], struct nlattr *data[],
@@ -1393,6 +1432,14 @@
 	dst_cache_reset(&geneve->cfg.info.dst_cache);
 	memcpy(&geneve->cfg, cfg, sizeof(*cfg));
 
+	if (geneve->cfg.inner_proto_inherit) {
+		dev->header_ops = NULL;
+		dev->type = ARPHRD_NONE;
+		dev->hard_header_len = 0;
+		dev->addr_len = 0;
+		dev->flags = IFF_NOARP;
+	}
+
 	err = register_netdevice(dev);
 	if (err)
 		return err;
@@ -1566,10 +1613,18 @@
 #endif
 	}
 
+	if (data[IFLA_GENEVE_INNER_PROTO_INHERIT]) {
+		if (changelink) {
+			attrtype = IFLA_GENEVE_INNER_PROTO_INHERIT;
+			goto change_notsup;
+		}
+		cfg->inner_proto_inherit = true;
+	}
+
 	return 0;
 change_notsup:
 	NL_SET_ERR_MSG_ATTR(extack, data[attrtype],
-			    "Changing VNI, Port, endpoint IP address family, external, and UDP checksum attributes are not supported");
+			    "Changing VNI, Port, endpoint IP address family, external, inner_proto_inherit, and UDP checksum attributes are not supported");
 	return -EOPNOTSUPP;
 }
 
@@ -1745,6 +1800,7 @@
 		nla_total_size(sizeof(__u8)) + /* IFLA_GENEVE_UDP_ZERO_CSUM6_TX */
 		nla_total_size(sizeof(__u8)) + /* IFLA_GENEVE_UDP_ZERO_CSUM6_RX */
 		nla_total_size(sizeof(__u8)) + /* IFLA_GENEVE_TTL_INHERIT */
+		nla_total_size(0) +	 /* IFLA_GENEVE_INNER_PROTO_INHERIT */
 		0;
 }
 
@@ -1804,6 +1860,10 @@
 	if (nla_put_u8(skb, IFLA_GENEVE_TTL_INHERIT, ttl_inherit))
 		goto nla_put_failure;
 
+	if (geneve->cfg.inner_proto_inherit &&
+	    nla_put_flag(skb, IFLA_GENEVE_INNER_PROTO_INHERIT))
+		goto nla_put_failure;
+
 	return 0;
 
 nla_put_failure:
@@ -1900,21 +1960,9 @@
 {
 	struct geneve_net *gn = net_generic(net, geneve_net_id);
 	struct geneve_dev *geneve, *next;
-	struct net_device *dev, *aux;
 
-	/* gather any geneve devices that were moved into this ns */
-	for_each_netdev_safe(net, dev, aux)
-		if (dev->rtnl_link_ops == &geneve_link_ops)
-			unregister_netdevice_queue(dev, head);
-
-	/* now gather any other geneve devices that were created in this ns */
-	list_for_each_entry_safe(geneve, next, &gn->geneve_list, next) {
-		/* If geneve->dev is in the same netns, it was already added
-		 * to the list by the previous loop.
-		 */
-		if (!net_eq(dev_net(geneve->dev), net))
-			unregister_netdevice_queue(geneve->dev, head);
-	}
+	list_for_each_entry_safe(geneve, next, &gn->geneve_list, next)
+		geneve_dellink(geneve->dev, head);
 }
 
 static void __net_exit geneve_exit_batch_net(struct list_head *net_list)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/gtp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/gtp.c
@@ -298,7 +298,9 @@
 			gtp->sk1u = NULL;
 		udp_sk(sk)->encap_type = 0;
 		rcu_assign_sk_user_data(sk, NULL);
+		release_sock(sk);
 		sock_put(sk);
+		return;
 	}
 	release_sock(sk);
 }
@@ -541,8 +543,9 @@
 
 	rt->dst.ops->update_pmtu(&rt->dst, NULL, skb, mtu, false);
 
-	if (!skb_is_gso(skb) && (iph->frag_off & htons(IP_DF)) &&
-	    mtu < ntohs(iph->tot_len)) {
+	if (iph->frag_off & htons(IP_DF) &&
+	    ((!skb_is_gso(skb) && skb->len > mtu) ||
+	     (skb_is_gso(skb) && !skb_gso_validate_network_len(skb, mtu)))) {
 		netdev_dbg(dev, "packet too big, fragmentation needed\n");
 		icmp_ndo_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED,
 			      htonl(mtu));
@@ -569,6 +572,9 @@
 	if (skb_cow_head(skb, dev->needed_headroom))
 		goto tx_err;
 
+	if (!pskb_inet_may_pull(skb))
+		goto tx_err;
+
 	skb_reset_inner_headers(skb);
 
 	/* PDP context lookups in gtp_build_skb_*() need rcu read-side lock. */
@@ -691,8 +697,8 @@
 		goto out_encap;
 	}
 
-	gn = net_generic(dev_net(dev), gtp_net_id);
-	list_add_rcu(&gtp->list, &gn->gtp_dev_list);
+	gn = net_generic(src_net, gtp_net_id);
+	list_add(&gtp->list, &gn->gtp_dev_list);
 	dev->priv_destructor = gtp_destructor;
 
 	netdev_dbg(dev, "registered new GTP interface\n");
@@ -710,14 +716,15 @@
 static void gtp_dellink(struct net_device *dev, struct list_head *head)
 {
 	struct gtp_dev *gtp = netdev_priv(dev);
+	struct hlist_node *next;
 	struct pdp_ctx *pctx;
 	int i;
 
 	for (i = 0; i < gtp->hash_size; i++)
-		hlist_for_each_entry_rcu(pctx, &gtp->tid_hash[i], hlist_tid)
+		hlist_for_each_entry_safe(pctx, next, &gtp->tid_hash[i], hlist_tid)
 			pdp_context_delete(pctx);
 
-	list_del_rcu(&gtp->list);
+	list_del(&gtp->list);
 	unregister_netdevice_queue(dev, head);
 }
 
@@ -810,7 +817,7 @@
 	sock = sockfd_lookup(fd, &err);
 	if (!sock) {
 		pr_debug("gtp socket fd=%d not found\n", fd);
-		return NULL;
+		return ERR_PTR(err);
 	}
 
 	sk = sock->sk;
@@ -851,20 +858,24 @@
 	unsigned int role = GTP_ROLE_GGSN;
 
 	if (data[IFLA_GTP_FD0]) {
-		u32 fd0 = nla_get_u32(data[IFLA_GTP_FD0]);
+		int fd0 = nla_get_u32(data[IFLA_GTP_FD0]);
 
-		sk0 = gtp_encap_enable_socket(fd0, UDP_ENCAP_GTP0, gtp);
-		if (IS_ERR(sk0))
-			return PTR_ERR(sk0);
+		if (fd0 >= 0) {
+			sk0 = gtp_encap_enable_socket(fd0, UDP_ENCAP_GTP0, gtp);
+			if (IS_ERR(sk0))
+				return PTR_ERR(sk0);
+		}
 	}
 
 	if (data[IFLA_GTP_FD1]) {
-		u32 fd1 = nla_get_u32(data[IFLA_GTP_FD1]);
+		int fd1 = nla_get_u32(data[IFLA_GTP_FD1]);
 
-		sk1u = gtp_encap_enable_socket(fd1, UDP_ENCAP_GTP1U, gtp);
-		if (IS_ERR(sk1u)) {
-			gtp_encap_disable_sock(sk0);
-			return PTR_ERR(sk1u);
+		if (fd1 >= 0) {
+			sk1u = gtp_encap_enable_socket(fd1, UDP_ENCAP_GTP1U, gtp);
+			if (IS_ERR(sk1u)) {
+				gtp_encap_disable_sock(sk0);
+				return PTR_ERR(sk1u);
+			}
 		}
 	}
 
@@ -1294,16 +1305,19 @@
 	struct gtp_dev *last_gtp = (struct gtp_dev *)cb->args[2], *gtp;
 	int i, j, bucket = cb->args[0], skip = cb->args[1];
 	struct net *net = sock_net(skb->sk);
+	struct net_device *dev;
 	struct pdp_ctx *pctx;
-	struct gtp_net *gn;
-
-	gn = net_generic(net, gtp_net_id);
 
 	if (cb->args[4])
 		return 0;
 
 	rcu_read_lock();
-	list_for_each_entry_rcu(gtp, &gn->gtp_dev_list, list) {
+	for_each_netdev_rcu(net, dev) {
+		if (dev->rtnl_link_ops != &gtp_link_ops)
+			continue;
+
+		gtp = netdev_priv(dev);
+
 		if (last_gtp && last_gtp != gtp)
 			continue;
 		else
@@ -1392,23 +1406,23 @@
 	return 0;
 }
 
-static void __net_exit gtp_net_exit(struct net *net)
+static void __net_exit gtp_net_exit_batch_rtnl(struct list_head *net_list,
+					       struct list_head *dev_to_kill)
 {
-	struct gtp_net *gn = net_generic(net, gtp_net_id);
-	struct gtp_dev *gtp;
-	LIST_HEAD(list);
+	struct net *net;
 
-	rtnl_lock();
-	list_for_each_entry(gtp, &gn->gtp_dev_list, list)
-		gtp_dellink(gtp->dev, &list);
+	list_for_each_entry(net, net_list, exit_list) {
+		struct gtp_net *gn = net_generic(net, gtp_net_id);
+		struct gtp_dev *gtp, *gtp_next;
 
-	unregister_netdevice_many(&list);
-	rtnl_unlock();
+		list_for_each_entry_safe(gtp, gtp_next, &gn->gtp_dev_list, list)
+			gtp_dellink(gtp->dev, dev_to_kill);
+	}
 }
 
 static struct pernet_operations gtp_net_ops = {
 	.init	= gtp_net_init,
-	.exit	= gtp_net_exit,
+	.exit_batch_rtnl = gtp_net_exit_batch_rtnl,
 	.id	= &gtp_net_id,
 	.size	= sizeof(struct gtp_net),
 };
@@ -1419,26 +1433,26 @@
 
 	get_random_bytes(&gtp_h_initval, sizeof(gtp_h_initval));
 
-	err = rtnl_link_register(&gtp_link_ops);
+	err = register_pernet_subsys(&gtp_net_ops);
 	if (err < 0)
 		goto error_out;
 
-	err = genl_register_family(&gtp_genl_family);
+	err = rtnl_link_register(&gtp_link_ops);
 	if (err < 0)
-		goto unreg_rtnl_link;
+		goto unreg_pernet_subsys;
 
-	err = register_pernet_subsys(&gtp_net_ops);
+	err = genl_register_family(&gtp_genl_family);
 	if (err < 0)
-		goto unreg_genl_family;
+		goto unreg_rtnl_link;
 
 	pr_info("GTP module loaded (pdp ctx size %zd bytes)\n",
 		sizeof(struct pdp_ctx));
 	return 0;
 
-unreg_genl_family:
-	genl_unregister_family(&gtp_genl_family);
 unreg_rtnl_link:
 	rtnl_link_unregister(&gtp_link_ops);
+unreg_pernet_subsys:
+	unregister_pernet_subsys(&gtp_net_ops);
 error_out:
 	pr_err("error loading GTP module loaded\n");
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hamradio/6pack.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hamradio/6pack.c
@@ -306,7 +306,6 @@
 {
 	/* Finish setting up the DEVICE info. */
 	dev->netdev_ops		= &sp_netdev_ops;
-	dev->needs_free_netdev	= true;
 	dev->mtu		= SIXP_MTU;
 	dev->hard_header_len	= AX25_MAX_HEADER_LEN;
 	dev->header_ops 	= &ax25_header_ops;
@@ -669,14 +668,16 @@
 	 */
 	netif_stop_queue(sp->dev);
 
+	unregister_netdev(sp->dev);
+
 	del_timer_sync(&sp->tx_t);
 	del_timer_sync(&sp->resync_t);
 
-	/* Free all 6pack frame buffers. */
+	/* Free all 6pack frame buffers after unreg. */
 	kfree(sp->rbuff);
 	kfree(sp->xbuff);
 
-	unregister_netdev(sp->dev);
+	free_netdev(sp->dev);
 }
 
 /* Perform I/O control on an active 6pack channel. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hamradio/baycom_epp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hamradio/baycom_epp.c
@@ -758,7 +758,7 @@
  * ===================== network driver interface =========================
  */
 
-static int baycom_send_packet(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t baycom_send_packet(struct sk_buff *skb, struct net_device *dev)
 {
 	struct baycom_state *bc = netdev_priv(dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hamradio/bpqether.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hamradio/bpqether.c
@@ -534,7 +534,7 @@
 	if (!net_eq(dev_net(dev), &init_net))
 		return NOTIFY_DONE;
 
-	if (!dev_is_ethdev(dev))
+	if (!dev_is_ethdev(dev) && !bpq_get_ax25_dev(dev))
 		return NOTIFY_DONE;
 
 	switch (event) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hamradio/mkiss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hamradio/mkiss.c
@@ -31,6 +31,8 @@
 
 #define AX_MTU		236
 
+/* some arch define END as assembly function ending, just undef it */
+#undef	END
 /* SLIP/KISS protocol characters. */
 #define END             0300		/* indicates end of frame	*/
 #define ESC             0333		/* indicates byte stuffing	*/
@@ -792,13 +794,14 @@
 	 */
 	netif_stop_queue(ax->dev);
 
-	/* Free all AX25 frame buffers. */
+	unregister_netdev(ax->dev);
+
+	/* Free all AX25 frame buffers after unreg. */
 	kfree(ax->rbuff);
 	kfree(ax->xbuff);
 
 	ax->tty = NULL;
 
-	unregister_netdev(ax->dev);
 	free_netdev(ax->dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hamradio/scc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hamradio/scc.c
@@ -301,12 +301,12 @@
 	spin_lock_irqsave(&scc->lock, flags);	
 	if (scc->tx_buff != NULL)
 	{
-		dev_kfree_skb(scc->tx_buff);
+		dev_kfree_skb_irq(scc->tx_buff);
 		scc->tx_buff = NULL;
 	}
 	
 	while (!skb_queue_empty(&scc->tx_queue))
-		dev_kfree_skb(skb_dequeue(&scc->tx_queue));
+		dev_kfree_skb_irq(skb_dequeue(&scc->tx_queue));
 
 	spin_unlock_irqrestore(&scc->lock, flags);
 }
@@ -1668,7 +1668,7 @@
 	if (skb_queue_len(&scc->tx_queue) > scc->dev->tx_queue_len) {
 		struct sk_buff *skb_del;
 		skb_del = skb_dequeue(&scc->tx_queue);
-		dev_kfree_skb(skb_del);
+		dev_kfree_skb_irq(skb_del);
 	}
 	skb_queue_tail(&scc->tx_queue, skb);
 	netif_trans_update(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hamradio/yam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hamradio/yam.c
@@ -950,9 +950,7 @@
 		ym = memdup_user(data, sizeof(struct yamdrv_ioctl_mcs));
 		if (IS_ERR(ym))
 			return PTR_ERR(ym);
-		if (ym->cmd != SIOCYAMSMCS)
-			return -EINVAL;
-		if (ym->bitrate > YAM_MAXBITRATE) {
+		if (ym->cmd != SIOCYAMSMCS || ym->bitrate > YAM_MAXBITRATE) {
 			kfree(ym);
 			return -EINVAL;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hippi/rrunner.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hippi/rrunner.c
@@ -1353,7 +1353,9 @@
 
 	rrpriv->fw_running = 0;
 
+	spin_unlock_irqrestore(&rrpriv->lock, flags);
 	del_timer_sync(&rrpriv->timer);
+	spin_lock_irqsave(&rrpriv->lock, flags);
 
 	writel(0, &regs->TxPi);
 	writel(0, &regs->IpRxPi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hyperv/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hyperv/Kconfig
@@ -3,5 +3,6 @@
 	tristate "Microsoft Hyper-V virtual network driver"
 	depends on HYPERV
 	select UCS2_STRING
+	select NLS
 	help
 	  Select this option to enable the Hyper-V virtual network driver.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hyperv/hyperv_net.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hyperv/hyperv_net.h
@@ -1037,7 +1037,8 @@
 	u32 vf_alloc;
 	/* Serial number of the VF to team with */
 	u32 vf_serial;
-
+	/* completion variable to confirm vf association */
+	struct completion vf_add;
 	/* Is the current data path through the VF NIC? */
 	bool  data_path_is_vf;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hyperv/netvsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hyperv/netvsc.c
@@ -710,7 +710,10 @@
 	/* Disable NAPI and disassociate its context from the device. */
 	for (i = 0; i < net_device->num_chn; i++) {
 		/* See also vmbus_reset_channel_cb(). */
-		napi_disable(&net_device->chan_table[i].napi);
+		/* only disable enabled NAPI channel */
+		if (i < ndev->real_num_rx_queues)
+			napi_disable(&net_device->chan_table[i].napi);
+
 		netif_napi_del(&net_device->chan_table[i].napi);
 	}
 
@@ -814,6 +817,7 @@
 	u32 msglen = hv_pkt_datalen(desc);
 	struct nvsp_message *pkt_rqst;
 	u64 cmd_rqst;
+	u32 status;
 
 	/* First check if this is a VMBUS completion without data payload */
 	if (!msglen) {
@@ -885,6 +889,23 @@
 		break;
 
 	case NVSP_MSG1_TYPE_SEND_RNDIS_PKT_COMPLETE:
+		if (msglen < sizeof(struct nvsp_message_header) +
+		    sizeof(struct nvsp_1_message_send_rndis_packet_complete)) {
+			if (net_ratelimit())
+				netdev_err(ndev, "nvsp_rndis_pkt_complete length too small: %u\n",
+					   msglen);
+			return;
+		}
+
+		/* If status indicates an error, output a message so we know
+		 * there's a problem. But process the completion anyway so the
+		 * resources are released.
+		 */
+		status = nvsp_packet->msg.v1_msg.send_rndis_pkt_complete.status;
+		if (status != NVSP_STAT_SUCCESS && net_ratelimit())
+			netdev_err(ndev, "nvsp_rndis_pkt_complete error status: %x\n",
+				   status);
+
 		netvsc_send_tx_complete(ndev, net_device, incoming_channel,
 					desc, budget);
 		break;
@@ -1450,6 +1471,10 @@
 
 	net_device_ctx->vf_alloc = nvmsg->msg.v4_msg.vf_assoc.allocated;
 	net_device_ctx->vf_serial = nvmsg->msg.v4_msg.vf_assoc.serial;
+
+	if (net_device_ctx->vf_alloc)
+		complete(&net_device_ctx->vf_add);
+
 	netdev_info(ndev, "VF slot %u %s\n",
 		    net_device_ctx->vf_serial,
 		    net_device_ctx->vf_alloc ? "added" : "removed");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/hyperv/netvsc_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/hyperv/netvsc_drv.c
@@ -42,9 +42,13 @@
 #define LINKCHANGE_INT (2 * HZ)
 #define VF_TAKEOVER_INT (HZ / 10)
 
+/* Macros to define the context of vf registration */
+#define VF_REG_IN_PROBE		1
+#define VF_REG_IN_NOTIFIER	2
+
 static unsigned int ring_size __ro_after_init = 128;
 module_param(ring_size, uint, 0444);
-MODULE_PARM_DESC(ring_size, "Ring buffer size (# of pages)");
+MODULE_PARM_DESC(ring_size, "Ring buffer size (# of 4K pages)");
 unsigned int netvsc_ring_bytes __ro_after_init;
 
 static const u32 default_msg = NETIF_MSG_DRV | NETIF_MSG_PROBE |
@@ -1586,6 +1590,9 @@
 	pcpu_sum = kvmalloc_array(num_possible_cpus(),
 				  sizeof(struct netvsc_ethtool_pcpu_stats),
 				  GFP_KERNEL);
+	if (!pcpu_sum)
+		return;
+
 	netvsc_get_pcpu_stats(dev, pcpu_sum);
 	for_each_present_cpu(cpu) {
 		struct netvsc_ethtool_pcpu_stats *this_sum = &pcpu_sum[cpu];
@@ -2201,7 +2208,7 @@
 }
 
 static int netvsc_vf_join(struct net_device *vf_netdev,
-			  struct net_device *ndev)
+			  struct net_device *ndev, int context)
 {
 	struct net_device_context *ndev_ctx = netdev_priv(ndev);
 	int ret;
@@ -2224,10 +2231,11 @@
 		goto upper_link_failed;
 	}
 
-	/* set slave flag before open to prevent IPv6 addrconf */
-	vf_netdev->flags |= IFF_SLAVE;
-
-	schedule_delayed_work(&ndev_ctx->vf_takeover, VF_TAKEOVER_INT);
+	/* If this registration is called from probe context vf_takeover
+	 * is taken care of later in probe itself.
+	 */
+	if (context == VF_REG_IN_NOTIFIER)
+		schedule_delayed_work(&ndev_ctx->vf_takeover, VF_TAKEOVER_INT);
 
 	call_netdevice_notifiers(NETDEV_JOIN, vf_netdev);
 
@@ -2333,12 +2341,39 @@
 
 	}
 
+	/* Fallback path to check synthetic vf with help of mac addr.
+	 * Because this function can be called before vf_netdev is
+	 * initialized (NETDEV_POST_INIT) when its perm_addr has not been copied
+	 * from dev_addr, also try to match to its dev_addr.
+	 * Note: On Hyper-V and Azure, it's not possible to set a MAC address
+	 * on a VF that matches to the MAC of a unrelated NETVSC device.
+	 */
+	list_for_each_entry(ndev_ctx, &netvsc_dev_list, list) {
+		ndev = hv_get_drvdata(ndev_ctx->device_ctx);
+		if (ether_addr_equal(vf_netdev->perm_addr, ndev->perm_addr) ||
+		    ether_addr_equal(vf_netdev->dev_addr, ndev->perm_addr))
+			return ndev;
+	}
+
 	netdev_notice(vf_netdev,
 		      "no netdev found for vf serial:%u\n", serial);
 	return NULL;
 }
 
-static int netvsc_register_vf(struct net_device *vf_netdev)
+static int netvsc_prepare_bonding(struct net_device *vf_netdev)
+{
+	struct net_device *ndev;
+
+	ndev = get_netvsc_byslot(vf_netdev);
+	if (!ndev)
+		return NOTIFY_DONE;
+
+	/* set slave flag before open to prevent IPv6 addrconf */
+	vf_netdev->flags |= IFF_SLAVE;
+	return NOTIFY_DONE;
+}
+
+static int netvsc_register_vf(struct net_device *vf_netdev, int context)
 {
 	struct net_device_context *net_device_ctx;
 	struct netvsc_device *netvsc_dev;
@@ -2378,7 +2413,7 @@
 
 	netdev_info(ndev, "VF registering: %s\n", vf_netdev->name);
 
-	if (netvsc_vf_join(vf_netdev, ndev) != 0)
+	if (netvsc_vf_join(vf_netdev, ndev, context) != 0)
 		return NOTIFY_DONE;
 
 	dev_hold(vf_netdev);
@@ -2429,6 +2464,11 @@
 	if (net_device_ctx->data_path_is_vf == vf_is_up)
 		return NOTIFY_OK;
 
+	if (vf_is_up && !net_device_ctx->vf_alloc) {
+		netdev_info(ndev, "Waiting for the VF association from host\n");
+		wait_for_completion(&net_device_ctx->vf_add);
+	}
+
 	ret = netvsc_switch_datapath(ndev, vf_is_up);
 
 	if (ret) {
@@ -2460,6 +2500,7 @@
 
 	netvsc_vf_setxdp(vf_netdev, NULL);
 
+	reinit_completion(&net_device_ctx->vf_add);
 	netdev_rx_handler_unregister(vf_netdev);
 	netdev_upper_dev_unlink(vf_netdev, ndev);
 	RCU_INIT_POINTER(net_device_ctx->vf_netdev, NULL);
@@ -2470,10 +2511,31 @@
 	return NOTIFY_OK;
 }
 
+static int check_dev_is_matching_vf(struct net_device *event_ndev)
+{
+	/* Skip NetVSC interfaces */
+	if (event_ndev->netdev_ops == &device_ops)
+		return -ENODEV;
+
+	/* Avoid non-Ethernet type devices */
+	if (event_ndev->type != ARPHRD_ETHER)
+		return -ENODEV;
+
+	/* Avoid Vlan dev with same MAC registering as VF */
+	if (is_vlan_dev(event_ndev))
+		return -ENODEV;
+
+	/* Avoid Bonding master dev with same MAC registering as VF */
+	if (netif_is_bond_master(event_ndev))
+		return -ENODEV;
+
+	return 0;
+}
+
 static int netvsc_probe(struct hv_device *dev,
 			const struct hv_vmbus_device_id *dev_id)
 {
-	struct net_device *net = NULL;
+	struct net_device *net = NULL, *vf_netdev;
 	struct net_device_context *net_device_ctx;
 	struct netvsc_device_info *device_info = NULL;
 	struct netvsc_device *nvdev;
@@ -2499,6 +2561,7 @@
 
 	INIT_DELAYED_WORK(&net_device_ctx->dwork, netvsc_link_change);
 
+	init_completion(&net_device_ctx->vf_add);
 	spin_lock_init(&net_device_ctx->lock);
 	INIT_LIST_HEAD(&net_device_ctx->reconfig_events);
 	INIT_DELAYED_WORK(&net_device_ctx->vf_takeover, netvsc_vf_setup);
@@ -2529,15 +2592,6 @@
 		goto devinfo_failed;
 	}
 
-	nvdev = rndis_filter_device_add(dev, device_info);
-	if (IS_ERR(nvdev)) {
-		ret = PTR_ERR(nvdev);
-		netdev_err(net, "unable to add netvsc device (ret %d)\n", ret);
-		goto rndis_failed;
-	}
-
-	memcpy(net->dev_addr, device_info->mac_adr, ETH_ALEN);
-
 	/* We must get rtnl lock before scheduling nvdev->subchan_work,
 	 * otherwise netvsc_subchan_work() can get rtnl lock first and wait
 	 * all subchannels to show up, but that may not happen because
@@ -2545,9 +2599,23 @@
 	 * -> ... -> device_add() -> ... -> __device_attach() can't get
 	 * the device lock, so all the subchannels can't be processed --
 	 * finally netvsc_subchan_work() hangs forever.
+	 *
+	 * The rtnl lock also needs to be held before rndis_filter_device_add()
+	 * which advertises nvsp_2_vsc_capability / sriov bit, and triggers
+	 * VF NIC offering and registering. If VF NIC finished register_netdev()
+	 * earlier it may cause name based config failure.
 	 */
 	rtnl_lock();
 
+	nvdev = rndis_filter_device_add(dev, device_info);
+	if (IS_ERR(nvdev)) {
+		ret = PTR_ERR(nvdev);
+		netdev_err(net, "unable to add netvsc device (ret %d)\n", ret);
+		goto rndis_failed;
+	}
+
+	memcpy(net->dev_addr, device_info->mac_adr, ETH_ALEN);
+
 	if (nvdev->num_chn > 1)
 		schedule_work(&nvdev->subchan_work);
 
@@ -2575,15 +2643,39 @@
 	}
 
 	list_add(&net_device_ctx->list, &netvsc_dev_list);
+
+	/* When the hv_netvsc driver is unloaded and reloaded, the
+	 * NET_DEVICE_REGISTER for the vf device is replayed before probe
+	 * is complete. This is because register_netdevice_notifier() gets
+	 * registered before vmbus_driver_register() so that callback func
+	 * is set before probe and we don't miss events like NETDEV_POST_INIT
+	 * So, in this section we try to register the matching vf device that
+	 * is present as a netdevice, knowing that its register call is not
+	 * processed in the netvsc_netdev_notifier(as probing is progress and
+	 * get_netvsc_byslot fails).
+	 */
+	for_each_netdev(dev_net(net), vf_netdev) {
+		ret = check_dev_is_matching_vf(vf_netdev);
+		if (ret != 0)
+			continue;
+
+		if (net != get_netvsc_byslot(vf_netdev))
+			continue;
+
+		netvsc_prepare_bonding(vf_netdev);
+		netvsc_register_vf(vf_netdev, VF_REG_IN_PROBE);
+		__netvsc_vf_setup(net, vf_netdev);
+		break;
+	}
 	rtnl_unlock();
 
 	netvsc_devinfo_put(device_info);
 	return 0;
 
 register_failed:
-	rtnl_unlock();
 	rndis_filter_device_remove(dev, nvdev);
 rndis_failed:
+	rtnl_unlock();
 	netvsc_devinfo_put(device_info);
 devinfo_failed:
 	free_percpu(net_device_ctx->vf_stats);
@@ -2662,7 +2754,10 @@
 
 	/* Save the current config info */
 	ndev_ctx->saved_netvsc_dev_info = netvsc_devinfo_get(nvdev);
-
+	if (!ndev_ctx->saved_netvsc_dev_info) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	ret = netvsc_detach(net, nvdev);
 out:
 	rtnl_unlock();
@@ -2718,6 +2813,31 @@
 	},
 };
 
+/* Set VF's namespace same as the synthetic NIC */
+static void netvsc_event_set_vf_ns(struct net_device *ndev)
+{
+	struct net_device_context *ndev_ctx = netdev_priv(ndev);
+	struct net_device *vf_netdev;
+	int ret;
+
+	vf_netdev = rtnl_dereference(ndev_ctx->vf_netdev);
+	if (!vf_netdev)
+		return;
+
+	if (!net_eq(dev_net(ndev), dev_net(vf_netdev))) {
+		ret = dev_change_net_namespace(vf_netdev, dev_net(ndev),
+					       "eth%d");
+		if (ret)
+			netdev_err(vf_netdev,
+				   "Cannot move to same namespace as %s: %d\n",
+				   ndev->name, ret);
+		else
+			netdev_info(vf_netdev,
+				    "Moved VF to namespace with: %s\n",
+				    ndev->name);
+	}
+}
+
 /*
  * On Hyper-V, every VF interface is matched with a corresponding
  * synthetic interface. The synthetic interface is presented first
@@ -2728,27 +2848,22 @@
 			       unsigned long event, void *ptr)
 {
 	struct net_device *event_dev = netdev_notifier_info_to_dev(ptr);
+	int ret = 0;
 
-	/* Skip our own events */
-	if (event_dev->netdev_ops == &device_ops)
-		return NOTIFY_DONE;
-
-	/* Avoid non-Ethernet type devices */
-	if (event_dev->type != ARPHRD_ETHER)
-		return NOTIFY_DONE;
-
-	/* Avoid Vlan dev with same MAC registering as VF */
-	if (is_vlan_dev(event_dev))
+	if (event_dev->netdev_ops == &device_ops && event == NETDEV_REGISTER) {
+		netvsc_event_set_vf_ns(event_dev);
 		return NOTIFY_DONE;
+	}
 
-	/* Avoid Bonding master dev with same MAC registering as VF */
-	if ((event_dev->priv_flags & IFF_BONDING) &&
-	    (event_dev->flags & IFF_MASTER))
+	ret = check_dev_is_matching_vf(event_dev);
+	if (ret != 0)
 		return NOTIFY_DONE;
 
 	switch (event) {
+	case NETDEV_POST_INIT:
+		return netvsc_prepare_bonding(event_dev);
 	case NETDEV_REGISTER:
-		return netvsc_register_vf(event_dev);
+		return netvsc_register_vf(event_dev, VF_REG_IN_NOTIFIER);
 	case NETDEV_UNREGISTER:
 		return netvsc_unregister_vf(event_dev);
 	case NETDEV_UP:
@@ -2780,14 +2895,19 @@
 		pr_info("Increased ring_size to %u (min allowed)\n",
 			ring_size);
 	}
-	netvsc_ring_bytes = ring_size * PAGE_SIZE;
+	netvsc_ring_bytes = VMBUS_RING_SIZE(ring_size * 4096);
+
+	register_netdevice_notifier(&netvsc_netdev_notifier);
 
 	ret = vmbus_driver_register(&netvsc_drv);
 	if (ret)
-		return ret;
+		goto err_vmbus_reg;
 
-	register_netdevice_notifier(&netvsc_netdev_notifier);
 	return 0;
+
+err_vmbus_reg:
+	unregister_netdevice_notifier(&netvsc_netdev_notifier);
+	return ret;
 }
 
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/Kconfig
@@ -108,6 +108,7 @@
 
 config IEEE802154_MCR20A
 	tristate "MCR20A transceiver driver"
+	select REGMAP_SPI
 	depends on IEEE802154_DRIVERS && MAC802154
 	depends on SPI
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/adf7242.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/adf7242.c
@@ -1162,9 +1162,10 @@
 
 static void adf7242_debugfs_init(struct adf7242_local *lp)
 {
-	char debugfs_dir_name[DNAME_INLINE_LEN + 1] = "adf7242-";
+	char debugfs_dir_name[DNAME_INLINE_LEN + 1];
 
-	strncat(debugfs_dir_name, dev_name(&lp->spi->dev), DNAME_INLINE_LEN);
+	snprintf(debugfs_dir_name, sizeof(debugfs_dir_name),
+		 "adf7242-%s", dev_name(&lp->spi->dev));
 
 	lp->debugfs_root = debugfs_create_dir(debugfs_dir_name, NULL);
 
@@ -1310,10 +1311,11 @@
 
 	debugfs_remove_recursive(lp->debugfs_root);
 
+	ieee802154_unregister_hw(lp->hw);
+
 	cancel_delayed_work_sync(&lp->work);
 	destroy_workqueue(lp->wqueue);
 
-	ieee802154_unregister_hw(lp->hw);
 	mutex_destroy(&lp->bmux);
 	ieee802154_free_hw(lp->hw);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/at86rf230.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/at86rf230.c
@@ -100,6 +100,7 @@
 	unsigned long cal_timeout;
 	bool is_tx;
 	bool is_tx_from_off;
+	bool was_tx;
 	u8 tx_retry;
 	struct sk_buff *tx_skb;
 	struct at86rf230_state_change tx;
@@ -343,7 +344,11 @@
 	if (ctx->free)
 		kfree(ctx);
 
-	ieee802154_wake_queue(lp->hw);
+	if (lp->was_tx) {
+		lp->was_tx = 0;
+		dev_kfree_skb_any(lp->tx_skb);
+		ieee802154_wake_queue(lp->hw);
+	}
 }
 
 static void
@@ -352,7 +357,11 @@
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
 
-	lp->is_tx = 0;
+	if (lp->is_tx) {
+		lp->was_tx = 1;
+		lp->is_tx = 0;
+	}
+
 	at86rf230_async_state_change(lp, ctx, STATE_RX_AACK_ON,
 				     at86rf230_async_error_recover_complete);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/atusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/atusb.c
@@ -93,7 +93,9 @@
 
 	ret = usb_control_msg(usb_dev, pipe, request, requesttype,
 			      value, index, data, size, timeout);
-	if (ret < 0) {
+	if (ret < size) {
+		ret = ret < 0 ? ret : -ENODATA;
+
 		atusb->err = ret;
 		dev_err(&usb_dev->dev,
 			"%s: req 0x%02x val 0x%x idx 0x%x, error %d\n",
@@ -861,9 +863,9 @@
 	if (!build)
 		return -ENOMEM;
 
-	ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0),
-				ATUSB_BUILD, ATUSB_REQ_FROM_DEV, 0, 0,
-				build, ATUSB_BUILD_SIZE, 1000);
+	/* We cannot call atusb_control_msg() here, since this request may read various length data */
+	ret = usb_control_msg(atusb->usb_dev, usb_rcvctrlpipe(usb_dev, 0), ATUSB_BUILD,
+			      ATUSB_REQ_FROM_DEV, 0, 0, build, ATUSB_BUILD_SIZE, 1000);
 	if (ret >= 0) {
 		build[ret] = 0;
 		dev_info(&usb_dev->dev, "Firmware: build %s\n", build);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/ca8210.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/ca8210.c
@@ -927,7 +927,7 @@
 
 	dev_dbg(&spi->dev, "%s called\n", __func__);
 
-	cas_ctl = kmalloc(sizeof(*cas_ctl), GFP_ATOMIC);
+	cas_ctl = kzalloc(sizeof(*cas_ctl), GFP_ATOMIC);
 	if (!cas_ctl)
 		return -ENOMEM;
 
@@ -1771,6 +1771,7 @@
 			status
 		);
 		if (status != MAC_TRANSACTION_OVERFLOW) {
+			dev_kfree_skb_any(priv->tx_skb);
 			ieee802154_wake_queue(priv->hw);
 			return 0;
 		}
@@ -1944,10 +1945,9 @@
 	struct ca8210_priv  *priv
 )
 {
-	int status;
 	struct ieee802154_hdr header = { };
 	struct secspec secspec;
-	unsigned int mac_len;
+	int mac_len, status;
 
 	dev_dbg(&priv->spi->dev, "%s called\n", __func__);
 
@@ -1955,6 +1955,8 @@
 	 * packet
 	 */
 	mac_len = ieee802154_hdr_peek_addrs(skb, &header);
+	if (mac_len < 0)
+		return mac_len;
 
 	secspec.security_level = header.sec.level;
 	secspec.key_id_mode = header.sec.key_id_mode;
@@ -2781,7 +2783,6 @@
 	struct device_node *np = spi->dev.of_node;
 	struct ca8210_priv *priv = spi_get_drvdata(spi);
 	struct ca8210_platform_data *pdata = spi->dev.platform_data;
-	int ret = 0;
 
 	if (!np)
 		return -EFAULT;
@@ -2798,18 +2799,8 @@
 		dev_crit(&spi->dev, "Failed to register external clk\n");
 		return PTR_ERR(priv->clk);
 	}
-	ret = of_clk_add_provider(np, of_clk_src_simple_get, priv->clk);
-	if (ret) {
-		clk_unregister(priv->clk);
-		dev_crit(
-			&spi->dev,
-			"Failed to register external clock as clock provider\n"
-		);
-	} else {
-		dev_info(&spi->dev, "External clock set as clock provider\n");
-	}
 
-	return ret;
+	return of_clk_add_provider(np, of_clk_src_simple_get, priv->clk);
 }
 
 /**
@@ -2821,8 +2812,8 @@
 {
 	struct ca8210_priv *priv = spi_get_drvdata(spi);
 
-	if (!priv->clk)
-		return
+	if (IS_ERR_OR_NULL(priv->clk))
+		return;
 
 	of_clk_del_provider(spi->dev.of_node);
 	clk_unregister(priv->clk);
@@ -2976,8 +2967,8 @@
 	ca8210_hw->phy->cca.opt = NL802154_CCA_OPT_ENERGY_CARRIER_AND;
 	ca8210_hw->phy->cca_ed_level = -9800;
 	ca8210_hw->phy->symbol_duration = 16;
-	ca8210_hw->phy->lifs_period = 40;
-	ca8210_hw->phy->sifs_period = 12;
+	ca8210_hw->phy->lifs_period = 40 * ca8210_hw->phy->symbol_duration;
+	ca8210_hw->phy->sifs_period = 12 * ca8210_hw->phy->symbol_duration;
 	ca8210_hw->flags =
 		IEEE802154_HW_AFILT |
 		IEEE802154_HW_OMIT_CKSUM |
@@ -3134,7 +3125,11 @@
 	spi_set_drvdata(priv->spi, priv);
 	if (IS_ENABLED(CONFIG_IEEE802154_CA8210_DEBUGFS)) {
 		cascoda_api_upstream = ca8210_test_int_driver_write;
-		ca8210_test_interface_init(priv);
+		ret = ca8210_test_interface_init(priv);
+		if (ret) {
+			dev_crit(&spi_device->dev, "ca8210_test_interface_init failed\n");
+			goto error;
+		}
 	} else {
 		cascoda_api_upstream = NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/cc2520.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/cc2520.c
@@ -504,6 +504,7 @@
 		goto err_tx;
 
 	if (status & CC2520_STATUS_TX_UNDERFLOW) {
+		rc = -EINVAL;
 		dev_err(&priv->spi->dev, "cc2520 tx underflow exception\n");
 		goto err_tx;
 	}
@@ -969,7 +970,7 @@
 
 		if (timeout-- <= 0) {
 			dev_err(&priv->spi->dev, "oscillator start failed!\n");
-			return ret;
+			return -ETIMEDOUT;
 		}
 		udelay(1);
 	} while (!(status & CC2520_STATUS_XOSC32M_STABLE));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/mac802154_hwsim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/mac802154_hwsim.c
@@ -522,7 +522,7 @@
 static int hwsim_set_edge_lqi(struct sk_buff *msg, struct genl_info *info)
 {
 	struct nlattr *edge_attrs[MAC802154_HWSIM_EDGE_ATTR_MAX + 1];
-	struct hwsim_edge_info *einfo;
+	struct hwsim_edge_info *einfo, *einfo_old;
 	struct hwsim_phy *phy_v0;
 	struct hwsim_edge *e;
 	u32 v0, v1;
@@ -560,8 +560,10 @@
 	list_for_each_entry_rcu(e, &phy_v0->edges, list) {
 		if (e->endpoint->idx == v1) {
 			einfo->lqi = lqi;
-			rcu_assign_pointer(e->info, einfo);
+			einfo_old = rcu_replace_pointer(e->info, einfo,
+							lockdep_is_held(&hwsim_phys_lock));
 			rcu_read_unlock();
+			kfree_rcu(einfo_old, rcu);
 			mutex_unlock(&hwsim_phys_lock);
 			return 0;
 		}
@@ -786,6 +788,7 @@
 		goto err_pib;
 	}
 
+	pib->channel = 13;
 	rcu_assign_pointer(phy->pib, pib);
 	phy->idx = idx;
 	INIT_LIST_HEAD(&phy->edges);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ieee802154/mcr20a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ieee802154/mcr20a.c
@@ -976,8 +976,8 @@
 	dev_dbg(printdev(lp), "%s\n", __func__);
 
 	phy->symbol_duration = 16;
-	phy->lifs_period = 40;
-	phy->sifs_period = 12;
+	phy->lifs_period = 40 * phy->symbol_duration;
+	phy->sifs_period = 12 * phy->symbol_duration;
 
 	hw->flags = IEEE802154_HW_TX_OMIT_CKSUM |
 			IEEE802154_HW_AFILT |
@@ -1311,16 +1311,13 @@
 		irq_type = IRQF_TRIGGER_FALLING;
 
 	ret = devm_request_irq(&spi->dev, spi->irq, mcr20a_irq_isr,
-			       irq_type, dev_name(&spi->dev), lp);
+			       irq_type | IRQF_NO_AUTOEN, dev_name(&spi->dev), lp);
 	if (ret) {
 		dev_err(&spi->dev, "could not request_irq for mcr20a\n");
 		ret = -ENODEV;
 		goto free_dev;
 	}
 
-	/* disable_irq by default and wait for starting hardware */
-	disable_irq(spi->irq);
-
 	ret = ieee802154_register_hw(hw);
 	if (ret) {
 		dev_crit(&spi->dev, "ieee802154_register_hw failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ifb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ifb.c
@@ -76,7 +76,9 @@
 
 	while ((skb = __skb_dequeue(&txp->tq)) != NULL) {
 		skb->redirected = 0;
+#ifdef CONFIG_NET_CLS_ACT
 		skb->tc_skip_classify = 1;
+#endif
 
 		u64_stats_update_begin(&txp->tsync);
 		txp->tx_packets++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/Kconfig
@@ -2,7 +2,9 @@
 	tristate "Qualcomm IPA support"
 	depends on NET && QCOM_SMEM
 	depends on ARCH_QCOM || COMPILE_TEST
+	depends on INTERCONNECT
 	depends on QCOM_RPROC_COMMON || (QCOM_RPROC_COMMON=n && COMPILE_TEST)
+	depends on QCOM_AOSS_QMP || QCOM_AOSS_QMP=n
 	select QCOM_MDT_LOADER if ARCH_QCOM
 	select QCOM_SCM
 	select QCOM_QMI_HELPERS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/gsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/gsi.c
@@ -1370,9 +1370,10 @@
 	struct gsi_event *event_done;
 	struct gsi_event *event;
 	struct gsi_trans *trans;
+	u32 trans_count = 0;
 	u32 byte_count = 0;
-	u32 old_index;
 	u32 event_avail;
+	u32 old_index;
 
 	trans_info = &channel->trans_info;
 
@@ -1393,6 +1394,7 @@
 	do {
 		trans->len = __le16_to_cpu(event->len);
 		byte_count += trans->len;
+		trans_count++;
 
 		/* Move on to the next event and transaction */
 		if (--event_avail)
@@ -1404,7 +1406,7 @@
 
 	/* We record RX bytes when they are received */
 	channel->byte_count += byte_count;
-	channel->trans_count++;
+	channel->trans_count += trans_count;
 }
 
 /* Initialize a ring, including allocating DMA memory for its entries */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/gsi_trans.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/gsi_trans.c
@@ -155,7 +155,7 @@
 	 * gsi_trans_pool_exit_dma() can assume the total allocated
 	 * size is exactly (count * size).
 	 */
-	total_size = get_order(total_size) << PAGE_SHIFT;
+	total_size = PAGE_SIZE << get_order(total_size);
 
 	virt = dma_alloc_coherent(dev, total_size, &addr, GFP_KERNEL);
 	if (!virt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_cmd.c
@@ -661,22 +661,6 @@
 	wait_for_completion(&ipa->completion);
 }
 
-void ipa_cmd_pipeline_clear(struct ipa *ipa)
-{
-	u32 count = ipa_cmd_pipeline_clear_count();
-	struct gsi_trans *trans;
-
-	trans = ipa_cmd_trans_alloc(ipa, count);
-	if (trans) {
-		ipa_cmd_pipeline_clear_add(trans);
-		gsi_trans_commit_wait(trans);
-		ipa_cmd_pipeline_clear_wait(ipa);
-	} else {
-		dev_err(&ipa->pdev->dev,
-			"error allocating %u entry tag transaction\n", count);
-	}
-}
-
 static struct ipa_cmd_info *
 ipa_cmd_info_alloc(struct ipa_endpoint *endpoint, u32 tre_count)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_cmd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_cmd.h
@@ -164,12 +164,6 @@
 void ipa_cmd_pipeline_clear_wait(struct ipa *ipa);
 
 /**
- * ipa_cmd_pipeline_clear() - Clear the hardware pipeline
- * @ipa:	- IPA pointer
- */
-void ipa_cmd_pipeline_clear(struct ipa *ipa);
-
-/**
  * ipa_cmd_trans_alloc() - Allocate a transaction for the command TX endpoint
  * @ipa:	IPA pointer
  * @tre_count:	Number of elements in the transaction
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_endpoint.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_endpoint.c
@@ -570,19 +570,23 @@
 	struct ipa *ipa = endpoint->ipa;
 	u32 val = 0;
 
-	val |= HDR_ENDIANNESS_FMASK;		/* big endian */
-
-	/* A QMAP header contains a 6 bit pad field at offset 0.  The RMNet
-	 * driver assumes this field is meaningful in packets it receives,
-	 * and assumes the header's payload length includes that padding.
-	 * The RMNet driver does *not* pad packets it sends, however, so
-	 * the pad field (although 0) should be ignored.
-	 */
-	if (endpoint->data->qmap && !endpoint->toward_ipa) {
-		val |= HDR_TOTAL_LEN_OR_PAD_VALID_FMASK;
-		/* HDR_TOTAL_LEN_OR_PAD is 0 (pad, not total_len) */
-		val |= HDR_PAYLOAD_LEN_INC_PADDING_FMASK;
-		/* HDR_TOTAL_LEN_OR_PAD_OFFSET is 0 */
+	if (endpoint->data->qmap) {
+		/* We have a header, so we must specify its endianness */
+		val |= HDR_ENDIANNESS_FMASK;	/* big endian */
+
+		/* A QMAP header contains a 6 bit pad field at offset 0.
+		 * The RMNet driver assumes this field is meaningful in
+		 * packets it receives, and assumes the header's payload
+		 * length includes that padding.  The RMNet driver does
+		 * *not* pad packets it sends, however, so the pad field
+		 * (although 0) should be ignored.
+		 */
+		if (!endpoint->toward_ipa) {
+			val |= HDR_TOTAL_LEN_OR_PAD_VALID_FMASK;
+			/* HDR_TOTAL_LEN_OR_PAD is 0 (pad, not total_len) */
+			val |= HDR_PAYLOAD_LEN_INC_PADDING_FMASK;
+			/* HDR_TOTAL_LEN_OR_PAD_OFFSET is 0 */
+		}
 	}
 
 	/* HDR_PAYLOAD_LEN_INC_PADDING is 0 */
@@ -722,13 +726,15 @@
 
 	if (endpoint->data->aggregation) {
 		if (!endpoint->toward_ipa) {
+			u32 buffer_size;
 			bool close_eof;
 			u32 limit;
 
 			val |= u32_encode_bits(IPA_ENABLE_AGGR, AGGR_EN_FMASK);
 			val |= u32_encode_bits(IPA_GENERIC, AGGR_TYPE_FMASK);
 
-			limit = ipa_aggr_size_kb(IPA_RX_BUFFER_SIZE);
+			buffer_size = IPA_RX_BUFFER_SIZE - NET_SKB_PAD;
+			limit = ipa_aggr_size_kb(buffer_size);
 			val |= aggr_byte_limit_encoded(version, limit);
 
 			limit = IPA_AGGR_TIME_LIMIT;
@@ -738,8 +744,6 @@
 
 			close_eof = endpoint->data->rx.aggr_close_eof;
 			val |= aggr_sw_eof_active_encoded(version, close_eof);
-
-			/* AGGR_HARD_BYTE_LIMIT_ENABLE is 0 */
 		} else {
 			val |= u32_encode_bits(IPA_ENABLE_DEAGGR,
 					       AGGR_EN_FMASK);
@@ -853,6 +857,7 @@
 	u32 offset;
 	u32 val;
 
+	/* This should only be changed when HOL_BLOCK_EN is disabled */
 	offset = IPA_REG_ENDP_INIT_HOL_BLOCK_TIMER_N_OFFSET(endpoint_id);
 	val = hol_block_timer_val(ipa, microseconds);
 	iowrite32(val, ipa->reg_virt + offset);
@@ -868,6 +873,9 @@
 	val = enable ? HOL_BLOCK_EN_FMASK : 0;
 	offset = IPA_REG_ENDP_INIT_HOL_BLOCK_EN_N_OFFSET(endpoint_id);
 	iowrite32(val, endpoint->ipa->reg_virt + offset);
+	/* When enabling, the register must be written twice for IPA v4.5+ */
+	if (enable && endpoint->ipa->version >= IPA_VERSION_4_5)
+		iowrite32(val, endpoint->ipa->reg_virt + offset);
 }
 
 void ipa_endpoint_modem_hol_block_clear_all(struct ipa *ipa)
@@ -880,6 +888,7 @@
 		if (endpoint->toward_ipa || endpoint->ee_id != GSI_EE_MODEM)
 			continue;
 
+		ipa_endpoint_init_hol_block_enable(endpoint, false);
 		ipa_endpoint_init_hol_block_timer(endpoint, 0);
 		ipa_endpoint_init_hol_block_enable(endpoint, true);
 	}
@@ -1040,7 +1049,7 @@
 err_trans_free:
 	gsi_trans_free(trans);
 err_free_pages:
-	__free_pages(page, get_order(IPA_RX_BUFFER_SIZE));
+	put_page(page);
 
 	return -ENOMEM;
 }
@@ -1062,27 +1071,38 @@
 {
 	struct gsi *gsi;
 	u32 backlog;
+	int delta;
 
-	if (!endpoint->replenish_enabled) {
+	if (!test_bit(IPA_REPLENISH_ENABLED, endpoint->replenish_flags)) {
 		if (add_one)
 			atomic_inc(&endpoint->replenish_saved);
 		return;
 	}
 
+	/* If already active, just update the backlog */
+	if (test_and_set_bit(IPA_REPLENISH_ACTIVE, endpoint->replenish_flags)) {
+		if (add_one)
+			atomic_inc(&endpoint->replenish_backlog);
+		return;
+	}
+
 	while (atomic_dec_not_zero(&endpoint->replenish_backlog))
 		if (ipa_endpoint_replenish_one(endpoint))
 			goto try_again_later;
+
+	clear_bit(IPA_REPLENISH_ACTIVE, endpoint->replenish_flags);
+
 	if (add_one)
 		atomic_inc(&endpoint->replenish_backlog);
 
 	return;
 
 try_again_later:
-	/* The last one didn't succeed, so fix the backlog */
-	backlog = atomic_inc_return(&endpoint->replenish_backlog);
+	clear_bit(IPA_REPLENISH_ACTIVE, endpoint->replenish_flags);
 
-	if (add_one)
-		atomic_inc(&endpoint->replenish_backlog);
+	/* The last one didn't succeed, so fix the backlog */
+	delta = add_one ? 2 : 1;
+	backlog = atomic_add_return(delta, &endpoint->replenish_backlog);
 
 	/* Whenever a receive buffer transaction completes we'll try to
 	 * replenish again.  It's unlikely, but if we fail to supply even
@@ -1102,7 +1122,7 @@
 	u32 max_backlog;
 	u32 saved;
 
-	endpoint->replenish_enabled = true;
+	set_bit(IPA_REPLENISH_ENABLED, endpoint->replenish_flags);
 	while ((saved = atomic_xchg(&endpoint->replenish_saved, 0)))
 		atomic_add(saved, &endpoint->replenish_backlog);
 
@@ -1116,7 +1136,7 @@
 {
 	u32 backlog;
 
-	endpoint->replenish_enabled = false;
+	clear_bit(IPA_REPLENISH_ENABLED, endpoint->replenish_flags);
 	while ((backlog = atomic_xchg(&endpoint->replenish_backlog, 0)))
 		atomic_add(backlog, &endpoint->replenish_saved);
 }
@@ -1369,7 +1389,7 @@
 		struct page *page = trans->data;
 
 		if (page)
-			__free_pages(page, get_order(IPA_RX_BUFFER_SIZE));
+			put_page(page);
 	}
 }
 
@@ -1631,8 +1651,6 @@
 	if (ipa->modem_netdev)
 		ipa_modem_suspend(ipa->modem_netdev);
 
-	ipa_cmd_pipeline_clear(ipa);
-
 	ipa_endpoint_suspend_one(ipa->name_map[IPA_ENDPOINT_AP_LAN_RX]);
 	ipa_endpoint_suspend_one(ipa->name_map[IPA_ENDPOINT_AP_COMMAND_TX]);
 }
@@ -1663,7 +1681,8 @@
 		/* RX transactions require a single TRE, so the maximum
 		 * backlog is the same as the maximum outstanding TREs.
 		 */
-		endpoint->replenish_enabled = false;
+		clear_bit(IPA_REPLENISH_ENABLED, endpoint->replenish_flags);
+		clear_bit(IPA_REPLENISH_ACTIVE, endpoint->replenish_flags);
 		atomic_set(&endpoint->replenish_saved,
 			   gsi_channel_tre_max(gsi, endpoint->channel_id));
 		atomic_set(&endpoint->replenish_backlog, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_endpoint.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_endpoint.h
@@ -41,6 +41,19 @@
 #define IPA_ENDPOINT_MAX		32	/* Max supported by driver */
 
 /**
+ * enum ipa_replenish_flag:	RX buffer replenish flags
+ *
+ * @IPA_REPLENISH_ENABLED:	Whether receive buffer replenishing is enabled
+ * @IPA_REPLENISH_ACTIVE:	Whether replenishing is underway
+ * @IPA_REPLENISH_COUNT:	Number of defined replenish flags
+ */
+enum ipa_replenish_flag {
+	IPA_REPLENISH_ENABLED,
+	IPA_REPLENISH_ACTIVE,
+	IPA_REPLENISH_COUNT,	/* Number of flags (must be last) */
+};
+
+/**
  * struct ipa_endpoint - IPA endpoint information
  * @ipa:		IPA pointer
  * @ee_id:		Execution environmnent endpoint is associated with
@@ -51,7 +64,7 @@
  * @trans_tre_max:	Maximum number of TRE descriptors per transaction
  * @evt_ring_id:	GSI event ring used by the endpoint
  * @netdev:		Network device pointer, if endpoint uses one
- * @replenish_enabled:	Whether receive buffer replenishing is enabled
+ * @replenish_flags:	Replenishing state flags
  * @replenish_ready:	Number of replenish transactions without doorbell
  * @replenish_saved:	Replenish requests held while disabled
  * @replenish_backlog:	Number of buffers needed to fill hardware queue
@@ -72,7 +85,7 @@
 	struct net_device *netdev;
 
 	/* Receive buffer replenishing for RX endpoints */
-	bool replenish_enabled;
+	DECLARE_BITMAP(replenish_flags, IPA_REPLENISH_COUNT);
 	u32 replenish_ready;
 	atomic_t replenish_saved;
 	atomic_t replenish_backlog;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_interrupt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_interrupt.c
@@ -122,6 +122,16 @@
 	return IRQ_HANDLED;
 }
 
+void ipa_interrupt_irq_disable(struct ipa *ipa)
+{
+	disable_irq(ipa->interrupt->irq);
+}
+
+void ipa_interrupt_irq_enable(struct ipa *ipa)
+{
+	enable_irq(ipa->interrupt->irq);
+}
+
 /* Common function used to enable/disable TX_SUSPEND for an endpoint */
 static void ipa_interrupt_suspend_control(struct ipa_interrupt *interrupt,
 					  u32 endpoint_id, bool enable)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_interrupt.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_interrupt.h
@@ -86,6 +86,22 @@
 void ipa_interrupt_simulate_suspend(struct ipa_interrupt *interrupt);
 
 /**
+ * ipa_interrupt_irq_enable() - Enable IPA interrupts
+ * @ipa:	IPA pointer
+ *
+ * This enables the IPA interrupt line
+ */
+void ipa_interrupt_irq_enable(struct ipa *ipa);
+
+/**
+ * ipa_interrupt_irq_disable() - Disable IPA interrupts
+ * @ipa:	IPA pointer
+ *
+ * This disables the IPA interrupt line
+ */
+void ipa_interrupt_irq_disable(struct ipa *ipa);
+
+/**
  * ipa_interrupt_config() - Configure the IPA interrupt framework
  * @ipa:	IPA pointer
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_main.c
@@ -28,6 +28,7 @@
 #include "ipa_reg.h"
 #include "ipa_mem.h"
 #include "ipa_table.h"
+#include "ipa_smp2p.h"
 #include "ipa_modem.h"
 #include "ipa_uc.h"
 #include "ipa_interrupt.h"
@@ -801,6 +802,11 @@
 	struct device *dev = &pdev->dev;
 	int ret;
 
+	/* Prevent the modem from triggering a call to ipa_setup().  This
+	 * also ensures a modem-initiated setup that's underway completes.
+	 */
+	ipa_smp2p_irq_disable_setup(ipa);
+
 	ret = pm_runtime_get_sync(dev);
 	if (WARN_ON(ret < 0))
 		goto out_power_put;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_mem.c
@@ -570,7 +570,7 @@
 	}
 
 	/* Align the address down and the size up to a page boundary */
-	addr = qcom_smem_virt_to_phys(virt) & PAGE_MASK;
+	addr = qcom_smem_virt_to_phys(virt);
 	phys = addr & PAGE_MASK;
 	size = PAGE_ALIGN(size + addr - phys);
 	iova = phys;	/* We just want a direct mapping */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_modem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_modem.c
@@ -339,9 +339,6 @@
 	if (state != IPA_MODEM_STATE_RUNNING)
 		return -EBUSY;
 
-	/* Prevent the modem from triggering a call to ipa_setup() */
-	ipa_smp2p_disable(ipa);
-
 	/* Clean up the netdev and endpoints if it was started */
 	if (netdev) {
 		struct ipa_priv *priv = netdev_priv(netdev);
@@ -369,6 +366,9 @@
 	struct device *dev = &ipa->pdev->dev;
 	int ret;
 
+	/* Prevent the modem from triggering a call to ipa_setup() */
+	ipa_smp2p_irq_disable_setup(ipa);
+
 	ret = pm_runtime_get_sync(dev);
 	if (ret < 0) {
 		dev_err(dev, "error %d getting power to handle crash\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_power.c
@@ -11,6 +11,8 @@
 #include <linux/pm_runtime.h>
 #include <linux/bitops.h>
 
+#include "linux/soc/qcom/qcom_aoss.h"
+
 #include "ipa.h"
 #include "ipa_power.h"
 #include "ipa_endpoint.h"
@@ -64,6 +66,7 @@
  * struct ipa_power - IPA power management information
  * @dev:		IPA device pointer
  * @core:		IPA core clock
+ * @qmp:		QMP handle for AOSS communication
  * @spinlock:		Protects modem TX queue enable/disable
  * @flags:		Boolean state flags
  * @interconnect_count:	Number of elements in interconnect[]
@@ -72,6 +75,7 @@
 struct ipa_power {
 	struct device *dev;
 	struct clk *core;
+	struct qmp *qmp;
 	spinlock_t spinlock;	/* used with STOPPED/STARTED power flags */
 	DECLARE_BITMAP(flags, IPA_POWER_FLAG_COUNT);
 	u32 interconnect_count;
@@ -273,6 +277,17 @@
 
 	__set_bit(IPA_POWER_FLAG_SYSTEM, ipa->power->flags);
 
+	/* Increment the disable depth to ensure that the IRQ won't
+	 * be re-enabled until the matching _enable call in
+	 * ipa_resume(). We do this to ensure that the interrupt
+	 * handler won't run whilst PM runtime is disabled.
+	 *
+	 * Note that disabling the IRQ is NOT the same as disabling
+	 * irq wake. If wakeup is enabled for the IPA then the IRQ
+	 * will still cause the system to wake up, see irq_set_irq_wake().
+	 */
+	ipa_interrupt_irq_disable(ipa);
+
 	return pm_runtime_force_suspend(dev);
 }
 
@@ -285,6 +300,12 @@
 
 	__clear_bit(IPA_POWER_FLAG_SYSTEM, ipa->power->flags);
 
+	/* Now that PM runtime is enabled again it's safe
+	 * to turn the IRQ back on and process any data
+	 * that was received during suspend.
+	 */
+	ipa_interrupt_irq_enable(ipa);
+
 	return ret;
 }
 
@@ -382,6 +403,47 @@
 	clear_bit(IPA_POWER_FLAG_STARTED, ipa->power->flags);
 }
 
+static int ipa_power_retention_init(struct ipa_power *power)
+{
+	struct qmp *qmp = qmp_get(power->dev);
+
+	if (IS_ERR(qmp)) {
+		if (PTR_ERR(qmp) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		/* We assume any other error means it's not defined/needed */
+		qmp = NULL;
+	}
+	power->qmp = qmp;
+
+	return 0;
+}
+
+static void ipa_power_retention_exit(struct ipa_power *power)
+{
+	qmp_put(power->qmp);
+	power->qmp = NULL;
+}
+
+/* Control register retention on power collapse */
+void ipa_power_retention(struct ipa *ipa, bool enable)
+{
+	static const char fmt[] = "{ class: bcm, res: ipa_pc, val: %c }";
+	struct ipa_power *power = ipa->power;
+	char buf[36];	/* Exactly enough for fmt[]; size a multiple of 4 */
+	int ret;
+
+	if (!power->qmp)
+		return;		/* Not needed on this platform */
+
+	(void)snprintf(buf, sizeof(buf), fmt, enable ? '1' : '0');
+
+	ret = qmp_send(power->qmp, buf, sizeof(buf));
+	if (ret)
+		dev_err(power->dev, "error %d sending QMP %sable request\n",
+			ret, enable ? "en" : "dis");
+}
+
 int ipa_power_setup(struct ipa *ipa)
 {
 	int ret;
@@ -438,12 +500,18 @@
 	if (ret)
 		goto err_kfree;
 
+	ret = ipa_power_retention_init(power);
+	if (ret)
+		goto err_interconnect_exit;
+
 	pm_runtime_set_autosuspend_delay(dev, IPA_AUTOSUSPEND_DELAY);
 	pm_runtime_use_autosuspend(dev);
 	pm_runtime_enable(dev);
 
 	return power;
 
+err_interconnect_exit:
+	ipa_interconnect_exit(power);
 err_kfree:
 	kfree(power);
 err_clk_put:
@@ -460,6 +528,7 @@
 
 	pm_runtime_disable(dev);
 	pm_runtime_dont_use_autosuspend(dev);
+	ipa_power_retention_exit(power);
 	ipa_interconnect_exit(power);
 	kfree(power);
 	clk_put(clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_power.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_power.h
@@ -41,6 +41,13 @@
 void ipa_power_modem_queue_active(struct ipa *ipa);
 
 /**
+ * ipa_power_retention() - Control register retention on power collapse
+ * @ipa:	IPA pointer
+ * @enable:	Whether retention should be enabled or disabled
+ */
+void ipa_power_retention(struct ipa *ipa, bool enable);
+
+/**
  * ipa_power_setup() - Set up IPA power management
  * @ipa:	IPA pointer
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_qmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_qmi.c
@@ -308,12 +308,12 @@
 	mem = ipa_mem_find(ipa, IPA_MEM_V4_ROUTE);
 	req.v4_route_tbl_info_valid = 1;
 	req.v4_route_tbl_info.start = ipa->mem_offset + mem->offset;
-	req.v4_route_tbl_info.count = mem->size / sizeof(__le64);
+	req.v4_route_tbl_info.end = IPA_ROUTE_MODEM_COUNT - 1;
 
 	mem = ipa_mem_find(ipa, IPA_MEM_V6_ROUTE);
 	req.v6_route_tbl_info_valid = 1;
 	req.v6_route_tbl_info.start = ipa->mem_offset + mem->offset;
-	req.v6_route_tbl_info.count = mem->size / sizeof(__le64);
+	req.v6_route_tbl_info.end = IPA_ROUTE_MODEM_COUNT - 1;
 
 	mem = ipa_mem_find(ipa, IPA_MEM_V4_FILTER);
 	req.v4_filter_tbl_start_valid = 1;
@@ -352,7 +352,7 @@
 		req.v4_hash_route_tbl_info_valid = 1;
 		req.v4_hash_route_tbl_info.start =
 				ipa->mem_offset + mem->offset;
-		req.v4_hash_route_tbl_info.count = mem->size / sizeof(__le64);
+		req.v4_hash_route_tbl_info.end = IPA_ROUTE_MODEM_COUNT - 1;
 	}
 
 	mem = ipa_mem_find(ipa, IPA_MEM_V6_ROUTE_HASHED);
@@ -360,7 +360,7 @@
 		req.v6_hash_route_tbl_info_valid = 1;
 		req.v6_hash_route_tbl_info.start =
 			ipa->mem_offset + mem->offset;
-		req.v6_hash_route_tbl_info.count = mem->size / sizeof(__le64);
+		req.v6_hash_route_tbl_info.end = IPA_ROUTE_MODEM_COUNT - 1;
 	}
 
 	mem = ipa_mem_find(ipa, IPA_MEM_V4_FILTER_HASHED);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_qmi_msg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_qmi_msg.c
@@ -311,7 +311,7 @@
 		.tlv_type	= 0x12,
 		.offset		= offsetof(struct ipa_init_modem_driver_req,
 					   v4_route_tbl_info),
-		.ei_array	= ipa_mem_array_ei,
+		.ei_array	= ipa_mem_bounds_ei,
 	},
 	{
 		.data_type	= QMI_OPT_FLAG,
@@ -332,7 +332,7 @@
 		.tlv_type	= 0x13,
 		.offset		= offsetof(struct ipa_init_modem_driver_req,
 					   v6_route_tbl_info),
-		.ei_array	= ipa_mem_array_ei,
+		.ei_array	= ipa_mem_bounds_ei,
 	},
 	{
 		.data_type	= QMI_OPT_FLAG,
@@ -496,7 +496,7 @@
 		.tlv_type	= 0x1b,
 		.offset		= offsetof(struct ipa_init_modem_driver_req,
 					   v4_hash_route_tbl_info),
-		.ei_array	= ipa_mem_array_ei,
+		.ei_array	= ipa_mem_bounds_ei,
 	},
 	{
 		.data_type	= QMI_OPT_FLAG,
@@ -517,7 +517,7 @@
 		.tlv_type	= 0x1c,
 		.offset		= offsetof(struct ipa_init_modem_driver_req,
 					   v6_hash_route_tbl_info),
-		.ei_array	= ipa_mem_array_ei,
+		.ei_array	= ipa_mem_bounds_ei,
 	},
 	{
 		.data_type	= QMI_OPT_FLAG,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_qmi_msg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_qmi_msg.h
@@ -86,9 +86,11 @@
 	IPA_QMI_PLATFORM_TYPE_MSM_QNX_V01	= 0x5,	/* QNX MSM */
 };
 
-/* This defines the start and end offset of a range of memory.  Both
- * fields are offsets relative to the start of IPA shared memory.
- * The end value is the last addressable byte *within* the range.
+/* This defines the start and end offset of a range of memory.  The start
+ * value is a byte offset relative to the start of IPA shared memory.  The
+ * end value is the last addressable unit *within* the range.  Typically
+ * the end value is in units of bytes, however it can also be a maximum
+ * array index value.
  */
 struct ipa_mem_bounds {
 	u32 start;
@@ -129,18 +131,19 @@
 	u8			hdr_tbl_info_valid;
 	struct ipa_mem_bounds	hdr_tbl_info;
 
-	/* Routing table information.  These define the location and size of
-	 * non-hashable IPv4 and IPv6 filter tables.  The start values are
-	 * offsets relative to the start of IPA shared memory.
+	/* Routing table information.  These define the location and maximum
+	 * *index* (not byte) for the modem portion of non-hashable IPv4 and
+	 * IPv6 routing tables.  The start values are byte offsets relative
+	 * to the start of IPA shared memory.
 	 */
 	u8			v4_route_tbl_info_valid;
-	struct ipa_mem_array	v4_route_tbl_info;
+	struct ipa_mem_bounds	v4_route_tbl_info;
 	u8			v6_route_tbl_info_valid;
-	struct ipa_mem_array	v6_route_tbl_info;
+	struct ipa_mem_bounds	v6_route_tbl_info;
 
 	/* Filter table information.  These define the location of the
 	 * non-hashable IPv4 and IPv6 filter tables.  The start values are
-	 * offsets relative to the start of IPA shared memory.
+	 * byte offsets relative to the start of IPA shared memory.
 	 */
 	u8			v4_filter_tbl_start_valid;
 	u32			v4_filter_tbl_start;
@@ -181,18 +184,20 @@
 	u8			zip_tbl_info_valid;
 	struct ipa_mem_bounds	zip_tbl_info;
 
-	/* Routing table information.  These define the location and size
-	 * of hashable IPv4 and IPv6 filter tables.  The start values are
-	 * offsets relative to the start of IPA shared memory.
+	/* Routing table information.  These define the location and maximum
+	 * *index* (not byte) for the modem portion of hashable IPv4 and IPv6
+	 * routing tables (if supported by hardware).  The start values are
+	 * byte offsets relative to the start of IPA shared memory.
 	 */
 	u8			v4_hash_route_tbl_info_valid;
-	struct ipa_mem_array	v4_hash_route_tbl_info;
+	struct ipa_mem_bounds	v4_hash_route_tbl_info;
 	u8			v6_hash_route_tbl_info_valid;
-	struct ipa_mem_array	v6_hash_route_tbl_info;
+	struct ipa_mem_bounds	v6_hash_route_tbl_info;
 
 	/* Filter table information.  These define the location and size
-	 * of hashable IPv4 and IPv6 filter tables.  The start values are
-	 * offsets relative to the start of IPA shared memory.
+	 * of hashable IPv4 and IPv6 filter tables (if supported by hardware).
+	 * The start values are byte offsets relative to the start of IPA
+	 * shared memory.
 	 */
 	u8			v4_hash_filter_tbl_start_valid;
 	u32			v4_hash_filter_tbl_start;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_resource.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_resource.c
@@ -52,7 +52,7 @@
 				return false;
 	}
 
-	group_count = data->rsrc_group_src_count;
+	group_count = data->rsrc_group_dst_count;
 	if (!group_count || group_count > IPA_RESOURCE_GROUP_MAX)
 		return false;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_smp2p.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_smp2p.c
@@ -53,7 +53,7 @@
  * @setup_ready_irq:	IPA interrupt triggered by modem to signal GSI ready
  * @power_on:		Whether IPA power is on
  * @notified:		Whether modem has been notified of power state
- * @disabled:		Whether setup ready interrupt handling is disabled
+ * @setup_disabled:	Whether setup ready interrupt handler is disabled
  * @mutex:		Mutex protecting ready-interrupt/shutdown interlock
  * @panic_notifier:	Panic notifier structure
 */
@@ -67,7 +67,7 @@
 	u32 setup_ready_irq;
 	bool power_on;
 	bool notified;
-	bool disabled;
+	bool setup_disabled;
 	struct mutex mutex;
 	struct notifier_block panic_notifier;
 };
@@ -155,11 +155,9 @@
 	struct device *dev;
 	int ret;
 
-	mutex_lock(&smp2p->mutex);
-
-	if (smp2p->disabled)
-		goto out_mutex_unlock;
-	smp2p->disabled = true;		/* If any others arrive, ignore them */
+	/* Ignore any (spurious) interrupts received after the first */
+	if (smp2p->ipa->setup_complete)
+		return IRQ_HANDLED;
 
 	/* Power needs to be active for setup */
 	dev = &smp2p->ipa->pdev->dev;
@@ -176,8 +174,6 @@
 out_power_put:
 	pm_runtime_mark_last_busy(dev);
 	(void)pm_runtime_put_autosuspend(dev);
-out_mutex_unlock:
-	mutex_unlock(&smp2p->mutex);
 
 	return IRQ_HANDLED;
 }
@@ -313,7 +309,7 @@
 	kfree(smp2p);
 }
 
-void ipa_smp2p_disable(struct ipa *ipa)
+void ipa_smp2p_irq_disable_setup(struct ipa *ipa)
 {
 	struct ipa_smp2p *smp2p = ipa->smp2p;
 
@@ -322,7 +318,10 @@
 
 	mutex_lock(&smp2p->mutex);
 
-	smp2p->disabled = true;
+	if (!smp2p->setup_disabled) {
+		disable_irq(smp2p->setup_ready_irq);
+		smp2p->setup_disabled = true;
+	}
 
 	mutex_unlock(&smp2p->mutex);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_smp2p.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_smp2p.h
@@ -27,13 +27,12 @@
 void ipa_smp2p_exit(struct ipa *ipa);
 
 /**
- * ipa_smp2p_disable() - Prevent "ipa-setup-ready" interrupt handling
+ * ipa_smp2p_irq_disable_setup() - Disable the "setup ready" interrupt
  * @ipa:	IPA pointer
  *
- * Prevent handling of the "setup ready" interrupt from the modem.
- * This is used before initiating shutdown of the driver.
+ * Disable the "ipa-setup-ready" interrupt from the modem.
  */
-void ipa_smp2p_disable(struct ipa *ipa);
+void ipa_smp2p_irq_disable_setup(struct ipa *ipa);
 
 /**
  * ipa_smp2p_notify_reset() - Reset modem notification state
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_table.c
@@ -108,8 +108,6 @@
 
 /* Assignment of route table entries to the modem and AP */
 #define IPA_ROUTE_MODEM_MIN		0
-#define IPA_ROUTE_MODEM_COUNT		8
-
 #define IPA_ROUTE_AP_MIN		IPA_ROUTE_MODEM_COUNT
 #define IPA_ROUTE_AP_COUNT \
 		(IPA_ROUTE_COUNT_MAX - IPA_ROUTE_MODEM_COUNT)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_table.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_table.h
@@ -13,6 +13,9 @@
 /* The maximum number of filter table entries (IPv4, IPv6; hashed or not) */
 #define IPA_FILTER_COUNT_MAX	14
 
+/* The number of route table entries allotted to the modem */
+#define IPA_ROUTE_MODEM_COUNT	8
+
 /* The maximum number of route table entries (IPv4, IPv6; hashed or not) */
 #define IPA_ROUTE_COUNT_MAX	15
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipa/ipa_uc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipa/ipa_uc.c
@@ -11,6 +11,7 @@
 
 #include "ipa.h"
 #include "ipa_uc.h"
+#include "ipa_power.h"
 
 /**
  * DOC:  The IPA embedded microcontroller
@@ -154,6 +155,7 @@
 	case IPA_UC_RESPONSE_INIT_COMPLETED:
 		if (ipa->uc_powered) {
 			ipa->uc_loaded = true;
+			ipa_power_retention(ipa, true);
 			pm_runtime_mark_last_busy(dev);
 			(void)pm_runtime_put_autosuspend(dev);
 			ipa->uc_powered = false;
@@ -184,6 +186,9 @@
 
 	ipa_interrupt_remove(ipa->interrupt, IPA_IRQ_UC_1);
 	ipa_interrupt_remove(ipa->interrupt, IPA_IRQ_UC_0);
+	if (ipa->uc_loaded)
+		ipa_power_retention(ipa, false);
+
 	if (!ipa->uc_powered)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipvlan/ipvlan_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipvlan/ipvlan_core.c
@@ -412,7 +412,7 @@
 	return addr;
 }
 
-static int ipvlan_process_v4_outbound(struct sk_buff *skb)
+static noinline_for_stack int ipvlan_process_v4_outbound(struct sk_buff *skb)
 {
 	const struct iphdr *ip4h = ip_hdr(skb);
 	struct net_device *dev = skb->dev;
@@ -437,27 +437,28 @@
 		goto err;
 	}
 	skb_dst_set(skb, &rt->dst);
-	err = ip_local_out(net, skb->sk, skb);
+
+	memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
+
+	err = ip_local_out(net, NULL, skb);
 	if (unlikely(net_xmit_eval(err)))
-		dev->stats.tx_errors++;
+		DEV_STATS_INC(dev, tx_errors);
 	else
 		ret = NET_XMIT_SUCCESS;
 	goto out;
 err:
-	dev->stats.tx_errors++;
+	DEV_STATS_INC(dev, tx_errors);
 	kfree_skb(skb);
 out:
 	return ret;
 }
 
 #if IS_ENABLED(CONFIG_IPV6)
-static int ipvlan_process_v6_outbound(struct sk_buff *skb)
+
+static noinline_for_stack int
+ipvlan_route_v6_outbound(struct net_device *dev, struct sk_buff *skb)
 {
 	const struct ipv6hdr *ip6h = ipv6_hdr(skb);
-	struct net_device *dev = skb->dev;
-	struct net *net = dev_net(dev);
-	struct dst_entry *dst;
-	int err, ret = NET_XMIT_DROP;
 	struct flowi6 fl6 = {
 		.flowi6_oif = dev->ifindex,
 		.daddr = ip6h->daddr,
@@ -467,24 +468,38 @@
 		.flowi6_mark = skb->mark,
 		.flowi6_proto = ip6h->nexthdr,
 	};
+	struct dst_entry *dst;
+	int err;
 
-	dst = ip6_route_output(net, NULL, &fl6);
-	if (dst->error) {
-		ret = dst->error;
+	dst = ip6_route_output(dev_net(dev), NULL, &fl6);
+	err = dst->error;
+	if (err) {
 		dst_release(dst);
-		goto err;
+		return err;
 	}
 	skb_dst_set(skb, dst);
-	err = ip6_local_out(net, skb->sk, skb);
+	return 0;
+}
+
+static int ipvlan_process_v6_outbound(struct sk_buff *skb)
+{
+	struct net_device *dev = skb->dev;
+	int err, ret = NET_XMIT_DROP;
+
+	err = ipvlan_route_v6_outbound(dev, skb);
+	if (unlikely(err)) {
+		DEV_STATS_INC(dev, tx_errors);
+		kfree_skb(skb);
+		return err;
+	}
+
+	memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
+
+	err = ip6_local_out(dev_net(dev), NULL, skb);
 	if (unlikely(net_xmit_eval(err)))
-		dev->stats.tx_errors++;
+		DEV_STATS_INC(dev, tx_errors);
 	else
 		ret = NET_XMIT_SUCCESS;
-	goto out;
-err:
-	dev->stats.tx_errors++;
-	kfree_skb(skb);
-out:
 	return ret;
 }
 #else
@@ -496,7 +511,6 @@
 
 static int ipvlan_process_outbound(struct sk_buff *skb)
 {
-	struct ethhdr *ethh = eth_hdr(skb);
 	int ret = NET_XMIT_DROP;
 
 	/* The ipvlan is a pseudo-L2 device, so the packets that we receive
@@ -506,6 +520,8 @@
 	if (skb_mac_header_was_set(skb)) {
 		/* In this mode we dont care about
 		 * multicast and broadcast traffic */
+		struct ethhdr *ethh = eth_hdr(skb);
+
 		if (is_multicast_ether_addr(ethh->h_dest)) {
 			pr_debug_ratelimited(
 				"Dropped {multi|broad}cast of type=[%x]\n",
@@ -579,7 +595,8 @@
 				consume_skb(skb);
 				return NET_XMIT_DROP;
 			}
-			return ipvlan_rcv_frame(addr, &skb, true);
+			ipvlan_rcv_frame(addr, &skb, true);
+			return NET_XMIT_SUCCESS;
 		}
 	}
 out:
@@ -590,7 +607,7 @@
 static int ipvlan_xmit_mode_l2(struct sk_buff *skb, struct net_device *dev)
 {
 	const struct ipvl_dev *ipvlan = netdev_priv(dev);
-	struct ethhdr *eth = eth_hdr(skb);
+	struct ethhdr *eth = skb_eth_hdr(skb);
 	struct ipvl_addr *addr;
 	void *lyr3h;
 	int addr_type;
@@ -605,7 +622,8 @@
 					consume_skb(skb);
 					return NET_XMIT_DROP;
 				}
-				return ipvlan_rcv_frame(addr, &skb, true);
+				ipvlan_rcv_frame(addr, &skb, true);
+				return NET_XMIT_SUCCESS;
 			}
 		}
 		skb = skb_share_check(skb, GFP_ATOMIC);
@@ -617,9 +635,11 @@
 		 * the skb for the main-dev. At the RX side we just return
 		 * RX_PASS for it to be processed further on the stack.
 		 */
-		return dev_forward_skb(ipvlan->phy_dev, skb);
+		dev_forward_skb(ipvlan->phy_dev, skb);
+		return NET_XMIT_SUCCESS;
 
 	} else if (is_multicast_ether_addr(eth->h_dest)) {
+		skb_reset_mac_header(skb);
 		ipvlan_skb_crossing_ns(skb, NULL);
 		ipvlan_multicast_enqueue(ipvlan->port, skb, true);
 		return NET_XMIT_SUCCESS;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipvlan/ipvlan_l3s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipvlan/ipvlan_l3s.c
@@ -101,6 +101,11 @@
 		goto out;
 
 	skb->dev = addr->master->dev;
+	skb->skb_iif = skb->dev->ifindex;
+#if IS_ENABLED(CONFIG_IPV6)
+	if (addr->atype == IPVL_IPV6)
+		IP6CB(skb)->iif = skb->dev->ifindex;
+#endif
 	len = skb->len + ETH_HLEN;
 	ipvlan_count_rx(addr->master, len, true, false);
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipvlan/ipvlan_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipvlan/ipvlan_main.c
@@ -324,6 +324,7 @@
 		s->rx_dropped = rx_errs;
 		s->tx_dropped = tx_drps;
 	}
+	s->tx_errors = DEV_STATS_READ(dev, tx_errors);
 }
 
 static int ipvlan_vlan_rx_add_vid(struct net_device *dev, __be16 proto, u16 vid)
@@ -748,7 +749,8 @@
 
 		write_pnet(&port->pnet, newnet);
 
-		ipvlan_migrate_l3s_hook(oldnet, newnet);
+		if (port->mode == IPVLAN_MODE_L3S)
+			ipvlan_migrate_l3s_hook(oldnet, newnet);
 		break;
 	}
 	case NETDEV_UNREGISTER:
@@ -787,7 +789,7 @@
 
 	case NETDEV_CHANGEADDR:
 		list_for_each_entry(ipvlan, &port->ipvlans, pnode) {
-			ether_addr_copy(ipvlan->dev->dev_addr, dev->dev_addr);
+			eth_hw_addr_set(ipvlan->dev, dev->dev_addr);
 			call_netdevice_notifiers(NETDEV_CHANGEADDR, ipvlan->dev);
 		}
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ipvlan/ipvtap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ipvlan/ipvtap.c
@@ -194,7 +194,7 @@
 	.notifier_call	= ipvtap_device_event,
 };
 
-static int ipvtap_init(void)
+static int __init ipvtap_init(void)
 {
 	int err;
 
@@ -228,7 +228,7 @@
 }
 module_init(ipvtap_init);
 
-static void ipvtap_exit(void)
+static void __exit ipvtap_exit(void)
 {
 	rtnl_link_unregister(&ipvtap_link_ops);
 	unregister_netdevice_notifier(&ipvtap_notifier_block);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/loopback.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/loopback.c
@@ -208,7 +208,7 @@
 	int err;
 
 	err = -ENOMEM;
-	dev = alloc_netdev(0, "lo", NET_NAME_UNKNOWN, loopback_setup);
+	dev = alloc_netdev(0, "lo", NET_NAME_PREDICTABLE, loopback_setup);
 	if (!dev)
 		goto out;
 
@@ -243,8 +243,22 @@
 	return NETDEV_TX_OK;
 }
 
+static int blackhole_neigh_output(struct neighbour *n, struct sk_buff *skb)
+{
+	kfree_skb(skb);
+	return 0;
+}
+
+static int blackhole_neigh_construct(struct net_device *dev,
+				     struct neighbour *n)
+{
+	n->output = blackhole_neigh_output;
+	return 0;
+}
+
 static const struct net_device_ops blackhole_netdev_ops = {
 	.ndo_start_xmit = blackhole_netdev_xmit,
+	.ndo_neigh_construct = blackhole_neigh_construct,
 };
 
 /* This is a dst-dummy device used specifically for invalidated
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/macsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/macsec.c
@@ -241,6 +241,7 @@
 #define DEFAULT_SEND_SCI true
 #define DEFAULT_ENCRYPT false
 #define DEFAULT_ENCODING_SA 0
+#define MACSEC_XPN_MAX_REPLAY_WINDOW (((1 << 30) - 1))
 
 static bool send_sci(const struct macsec_secy *secy)
 {
@@ -446,11 +447,6 @@
 	return (struct macsec_eth_header *)skb_mac_header(skb);
 }
 
-static sci_t dev_to_sci(struct net_device *dev, __be16 port)
-{
-	return make_sci(dev->dev_addr, port);
-}
-
 static void __macsec_pn_wrapped(struct macsec_secy *secy,
 				struct macsec_tx_sa *tx_sa)
 {
@@ -497,18 +493,28 @@
 	skb->protocol = eth_hdr(skb)->h_proto;
 }
 
+static unsigned int macsec_msdu_len(struct sk_buff *skb)
+{
+	struct macsec_dev *macsec = macsec_priv(skb->dev);
+	struct macsec_secy *secy = &macsec->secy;
+	bool sci_present = macsec_skb_cb(skb)->has_sci;
+
+	return skb->len - macsec_hdr_len(sci_present) - secy->icv_len;
+}
+
 static void macsec_count_tx(struct sk_buff *skb, struct macsec_tx_sc *tx_sc,
 			    struct macsec_tx_sa *tx_sa)
 {
+	unsigned int msdu_len = macsec_msdu_len(skb);
 	struct pcpu_tx_sc_stats *txsc_stats = this_cpu_ptr(tx_sc->stats);
 
 	u64_stats_update_begin(&txsc_stats->syncp);
 	if (tx_sc->encrypt) {
-		txsc_stats->stats.OutOctetsEncrypted += skb->len;
+		txsc_stats->stats.OutOctetsEncrypted += msdu_len;
 		txsc_stats->stats.OutPktsEncrypted++;
 		this_cpu_inc(tx_sa->stats->OutPktsEncrypted);
 	} else {
-		txsc_stats->stats.OutOctetsProtected += skb->len;
+		txsc_stats->stats.OutOctetsProtected += msdu_len;
 		txsc_stats->stats.OutPktsProtected++;
 		this_cpu_inc(tx_sa->stats->OutPktsProtected);
 	}
@@ -538,9 +544,10 @@
 	aead_request_free(macsec_skb_cb(skb)->req);
 
 	rcu_read_lock_bh();
-	macsec_encrypt_finish(skb, dev);
 	macsec_count_tx(skb, &macsec->secy.tx_sc, macsec_skb_cb(skb)->tx_sa);
-	len = skb->len;
+	/* packet is encrypted/protected so tx_bytes must be calculated */
+	len = macsec_msdu_len(skb) + 2 * ETH_ALEN;
+	macsec_encrypt_finish(skb, dev);
 	ret = dev_queue_xmit(skb);
 	count_tx(dev, ret, len);
 	rcu_read_unlock_bh();
@@ -699,6 +706,7 @@
 
 	macsec_skb_cb(skb)->req = req;
 	macsec_skb_cb(skb)->tx_sa = tx_sa;
+	macsec_skb_cb(skb)->has_sci = sci_present;
 	aead_request_set_callback(req, 0, macsec_encrypt_done, skb);
 
 	dev_hold(skb->dev);
@@ -740,15 +748,17 @@
 		u64_stats_update_begin(&rxsc_stats->syncp);
 		rxsc_stats->stats.InPktsLate++;
 		u64_stats_update_end(&rxsc_stats->syncp);
+		DEV_STATS_INC(secy->netdev, rx_dropped);
 		return false;
 	}
 
 	if (secy->validate_frames != MACSEC_VALIDATE_DISABLED) {
+		unsigned int msdu_len = macsec_msdu_len(skb);
 		u64_stats_update_begin(&rxsc_stats->syncp);
 		if (hdr->tci_an & MACSEC_TCI_E)
-			rxsc_stats->stats.InOctetsDecrypted += skb->len;
+			rxsc_stats->stats.InOctetsDecrypted += msdu_len;
 		else
-			rxsc_stats->stats.InOctetsValidated += skb->len;
+			rxsc_stats->stats.InOctetsValidated += msdu_len;
 		u64_stats_update_end(&rxsc_stats->syncp);
 	}
 
@@ -761,6 +771,8 @@
 			u64_stats_update_begin(&rxsc_stats->syncp);
 			rxsc_stats->stats.InPktsNotValid++;
 			u64_stats_update_end(&rxsc_stats->syncp);
+			this_cpu_inc(rx_sa->stats->InPktsNotValid);
+			DEV_STATS_INC(secy->netdev, rx_errors);
 			return false;
 		}
 
@@ -853,9 +865,9 @@
 
 	macsec_finalize_skb(skb, macsec->secy.icv_len,
 			    macsec_extra_len(macsec_skb_cb(skb)->has_sci));
+	len = skb->len;
 	macsec_reset_skb(skb, macsec->secy.netdev);
 
-	len = skb->len;
 	if (gro_cells_receive(&macsec->gro_cells, skb) == NET_RX_SUCCESS)
 		count_rx(dev, len);
 
@@ -1046,6 +1058,7 @@
 			u64_stats_update_begin(&secy_stats->syncp);
 			secy_stats->stats.InPktsNoTag++;
 			u64_stats_update_end(&secy_stats->syncp);
+			DEV_STATS_INC(macsec->secy.netdev, rx_dropped);
 			continue;
 		}
 
@@ -1155,6 +1168,7 @@
 		u64_stats_update_begin(&secy_stats->syncp);
 		secy_stats->stats.InPktsBadTag++;
 		u64_stats_update_end(&secy_stats->syncp);
+		DEV_STATS_INC(secy->netdev, rx_errors);
 		goto drop_nosa;
 	}
 
@@ -1170,6 +1184,7 @@
 			u64_stats_update_begin(&rxsc_stats->syncp);
 			rxsc_stats->stats.InPktsNotUsingSA++;
 			u64_stats_update_end(&rxsc_stats->syncp);
+			DEV_STATS_INC(secy->netdev, rx_errors);
 			goto drop_nosa;
 		}
 
@@ -1199,6 +1214,7 @@
 			u64_stats_update_begin(&rxsc_stats->syncp);
 			rxsc_stats->stats.InPktsLate++;
 			u64_stats_update_end(&rxsc_stats->syncp);
+			DEV_STATS_INC(macsec->secy.netdev, rx_dropped);
 			goto drop;
 		}
 	}
@@ -1227,6 +1243,7 @@
 deliver:
 	macsec_finalize_skb(skb, secy->icv_len,
 			    macsec_extra_len(macsec_skb_cb(skb)->has_sci));
+	len = skb->len;
 	macsec_reset_skb(skb, secy->netdev);
 
 	if (rx_sa)
@@ -1234,12 +1251,11 @@
 	macsec_rxsc_put(rx_sc);
 
 	skb_orphan(skb);
-	len = skb->len;
 	ret = gro_cells_receive(&macsec->gro_cells, skb);
 	if (ret == NET_RX_SUCCESS)
 		count_rx(dev, len);
 	else
-		macsec->secy.netdev->stats.rx_dropped++;
+		DEV_STATS_INC(macsec->secy.netdev, rx_dropped);
 
 	rcu_read_unlock();
 
@@ -1276,6 +1292,7 @@
 			u64_stats_update_begin(&secy_stats->syncp);
 			secy_stats->stats.InPktsNoSCI++;
 			u64_stats_update_end(&secy_stats->syncp);
+			DEV_STATS_INC(macsec->secy.netdev, rx_errors);
 			continue;
 		}
 
@@ -1294,7 +1311,7 @@
 			secy_stats->stats.InPktsUnknownSCI++;
 			u64_stats_update_end(&secy_stats->syncp);
 		} else {
-			macsec->secy.netdev->stats.rx_dropped++;
+			DEV_STATS_INC(macsec->secy.netdev, rx_dropped);
 		}
 	}
 
@@ -1308,8 +1325,7 @@
 	struct crypto_aead *tfm;
 	int ret;
 
-	/* Pick a sync gcm(aes) cipher to ensure order is preserved. */
-	tfm = crypto_alloc_aead("gcm(aes)", 0, CRYPTO_ALG_ASYNC);
+	tfm = crypto_alloc_aead("gcm(aes)", 0, 0);
 
 	if (IS_ERR(tfm))
 		return tfm;
@@ -1390,7 +1406,8 @@
 	return NULL;
 }
 
-static struct macsec_rx_sc *create_rx_sc(struct net_device *dev, sci_t sci)
+static struct macsec_rx_sc *create_rx_sc(struct net_device *dev, sci_t sci,
+					 bool active)
 {
 	struct macsec_rx_sc *rx_sc;
 	struct macsec_dev *macsec;
@@ -1414,7 +1431,7 @@
 	}
 
 	rx_sc->sci = sci;
-	rx_sc->active = true;
+	rx_sc->active = active;
 	refcount_set(&rx_sc->refcnt, 1);
 
 	secy = &macsec_priv(dev)->secy;
@@ -1695,7 +1712,7 @@
 		return false;
 
 	if (attrs[MACSEC_SA_ATTR_PN] &&
-	    *(u64 *)nla_data(attrs[MACSEC_SA_ATTR_PN]) == 0)
+	    nla_get_u64(attrs[MACSEC_SA_ATTR_PN]) == 0)
 		return false;
 
 	if (attrs[MACSEC_SA_ATTR_ACTIVE]) {
@@ -1751,7 +1768,8 @@
 	}
 
 	pn_len = secy->xpn ? MACSEC_XPN_PN_LEN : MACSEC_DEFAULT_PN_LEN;
-	if (nla_len(tb_sa[MACSEC_SA_ATTR_PN]) != pn_len) {
+	if (tb_sa[MACSEC_SA_ATTR_PN] &&
+	    nla_len(tb_sa[MACSEC_SA_ATTR_PN]) != pn_len) {
 		pr_notice("macsec: nl: add_rxsa: bad pn length: %d != %d\n",
 			  nla_len(tb_sa[MACSEC_SA_ATTR_PN]), pn_len);
 		rtnl_unlock();
@@ -1767,7 +1785,7 @@
 		if (nla_len(tb_sa[MACSEC_SA_ATTR_SALT]) != MACSEC_SALT_LEN) {
 			pr_notice("macsec: nl: add_rxsa: bad salt length: %d != %d\n",
 				  nla_len(tb_sa[MACSEC_SA_ATTR_SALT]),
-				  MACSEC_SA_ATTR_SALT);
+				  MACSEC_SALT_LEN);
 			rtnl_unlock();
 			return -EINVAL;
 		}
@@ -1822,6 +1840,7 @@
 		       secy->key_len);
 
 		err = macsec_offload(ops->mdo_add_rxsa, &ctx);
+		memzero_explicit(ctx.sa.key, secy->key_len);
 		if (err)
 			goto cleanup;
 	}
@@ -1840,7 +1859,7 @@
 	return 0;
 
 cleanup:
-	kfree(rx_sa);
+	macsec_rxsa_put(rx_sa);
 	rtnl_unlock();
 	return err;
 }
@@ -1866,7 +1885,7 @@
 	struct macsec_rx_sc *rx_sc;
 	struct nlattr *tb_rxsc[MACSEC_RXSC_ATTR_MAX + 1];
 	struct macsec_secy *secy;
-	bool was_active;
+	bool active = true;
 	int ret;
 
 	if (!attrs[MACSEC_ATTR_IFINDEX])
@@ -1888,16 +1907,15 @@
 	secy = &macsec_priv(dev)->secy;
 	sci = nla_get_sci(tb_rxsc[MACSEC_RXSC_ATTR_SCI]);
 
-	rx_sc = create_rx_sc(dev, sci);
+	if (tb_rxsc[MACSEC_RXSC_ATTR_ACTIVE])
+		active = nla_get_u8(tb_rxsc[MACSEC_RXSC_ATTR_ACTIVE]);
+
+	rx_sc = create_rx_sc(dev, sci, active);
 	if (IS_ERR(rx_sc)) {
 		rtnl_unlock();
 		return PTR_ERR(rx_sc);
 	}
 
-	was_active = rx_sc->active;
-	if (tb_rxsc[MACSEC_RXSC_ATTR_ACTIVE])
-		rx_sc->active = !!nla_get_u8(tb_rxsc[MACSEC_RXSC_ATTR_ACTIVE]);
-
 	if (macsec_is_offloaded(netdev_priv(dev))) {
 		const struct macsec_ops *ops;
 		struct macsec_context ctx;
@@ -1921,7 +1939,8 @@
 	return 0;
 
 cleanup:
-	rx_sc->active = was_active;
+	del_rx_sc(secy, sci);
+	free_rx_sc(rx_sc);
 	rtnl_unlock();
 	return ret;
 }
@@ -1937,7 +1956,7 @@
 	if (nla_get_u8(attrs[MACSEC_SA_ATTR_AN]) >= MACSEC_NUM_AN)
 		return false;
 
-	if (nla_get_u32(attrs[MACSEC_SA_ATTR_PN]) == 0)
+	if (nla_get_u64(attrs[MACSEC_SA_ATTR_PN]) == 0)
 		return false;
 
 	if (attrs[MACSEC_SA_ATTR_ACTIVE]) {
@@ -2009,7 +2028,7 @@
 		if (nla_len(tb_sa[MACSEC_SA_ATTR_SALT]) != MACSEC_SALT_LEN) {
 			pr_notice("macsec: nl: add_txsa: bad salt length: %d != %d\n",
 				  nla_len(tb_sa[MACSEC_SA_ATTR_SALT]),
-				  MACSEC_SA_ATTR_SALT);
+				  MACSEC_SALT_LEN);
 			rtnl_unlock();
 			return -EINVAL;
 		}
@@ -2064,6 +2083,7 @@
 		       secy->key_len);
 
 		err = macsec_offload(ops->mdo_add_txsa, &ctx);
+		memzero_explicit(ctx.sa.key, secy->key_len);
 		if (err)
 			goto cleanup;
 	}
@@ -2083,7 +2103,7 @@
 
 cleanup:
 	secy->operational = was_operational;
-	kfree(tx_sa);
+	macsec_txsa_put(tx_sa);
 	rtnl_unlock();
 	return err;
 }
@@ -2291,7 +2311,7 @@
 	if (nla_get_u8(attrs[MACSEC_SA_ATTR_AN]) >= MACSEC_NUM_AN)
 		return false;
 
-	if (attrs[MACSEC_SA_ATTR_PN] && nla_get_u32(attrs[MACSEC_SA_ATTR_PN]) == 0)
+	if (attrs[MACSEC_SA_ATTR_PN] && nla_get_u64(attrs[MACSEC_SA_ATTR_PN]) == 0)
 		return false;
 
 	if (attrs[MACSEC_SA_ATTR_ACTIVE]) {
@@ -2372,6 +2392,7 @@
 
 		ctx.sa.assoc_num = assoc_num;
 		ctx.sa.tx_sa = tx_sa;
+		ctx.sa.update_pn = !!prev_pn.full64;
 		ctx.secy = secy;
 
 		ret = macsec_offload(ops->mdo_upd_txsa, &ctx);
@@ -2465,6 +2486,7 @@
 
 		ctx.sa.assoc_num = assoc_num;
 		ctx.sa.rx_sa = rx_sa;
+		ctx.sa.update_pn = !!prev_pn.full64;
 		ctx.secy = secy;
 
 		ret = macsec_offload(ops->mdo_upd_rxsa, &ctx);
@@ -2560,7 +2582,7 @@
 	struct macsec_tx_sc *tx_sc = &secy->tx_sc;
 	int i;
 
-	if (secy->n_rx_sc > 0)
+	if (secy->rx_sc)
 		return true;
 
 	for (i = 0; i < MACSEC_NUM_AN; i++)
@@ -2580,7 +2602,7 @@
 	const struct macsec_ops *ops;
 	struct macsec_context ctx;
 	struct macsec_dev *macsec;
-	int ret;
+	int ret = 0;
 
 	if (!attrs[MACSEC_ATTR_IFINDEX])
 		return -EINVAL;
@@ -2593,28 +2615,36 @@
 					macsec_genl_offload_policy, NULL))
 		return -EINVAL;
 
+	rtnl_lock();
+
 	dev = get_dev_from_nl(genl_info_net(info), attrs);
-	if (IS_ERR(dev))
-		return PTR_ERR(dev);
+	if (IS_ERR(dev)) {
+		ret = PTR_ERR(dev);
+		goto out;
+	}
 	macsec = macsec_priv(dev);
 
-	if (!tb_offload[MACSEC_OFFLOAD_ATTR_TYPE])
-		return -EINVAL;
+	if (!tb_offload[MACSEC_OFFLOAD_ATTR_TYPE]) {
+		ret = -EINVAL;
+		goto out;
+	}
 
 	offload = nla_get_u8(tb_offload[MACSEC_OFFLOAD_ATTR_TYPE]);
 	if (macsec->offload == offload)
-		return 0;
+		goto out;
 
 	/* Check if the offloading mode is supported by the underlying layers */
 	if (offload != MACSEC_OFFLOAD_OFF &&
-	    !macsec_check_offload(offload, macsec))
-		return -EOPNOTSUPP;
+	    !macsec_check_offload(offload, macsec)) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
 
 	/* Check if the net device is busy. */
-	if (netif_running(dev))
-		return -EBUSY;
-
-	rtnl_lock();
+	if (netif_running(dev)) {
+		ret = -EBUSY;
+		goto out;
+	}
 
 	prev_offload = macsec->offload;
 	macsec->offload = offload;
@@ -2644,17 +2674,12 @@
 	if (ret)
 		goto rollback;
 
-	/* Force features update, since they are different for SW MACSec and
-	 * HW offloading cases.
-	 */
-	netdev_update_features(dev);
-
 	rtnl_unlock();
 	return 0;
 
 rollback:
 	macsec->offload = prev_offload;
-
+out:
 	rtnl_unlock();
 	return ret;
 }
@@ -3396,36 +3421,29 @@
 
 	if (!secy->operational) {
 		kfree_skb(skb);
-		dev->stats.tx_dropped++;
+		DEV_STATS_INC(dev, tx_dropped);
 		return NETDEV_TX_OK;
 	}
 
+	len = skb->len;
 	skb = macsec_encrypt(skb, dev);
 	if (IS_ERR(skb)) {
 		if (PTR_ERR(skb) != -EINPROGRESS)
-			dev->stats.tx_dropped++;
+			DEV_STATS_INC(dev, tx_dropped);
 		return NETDEV_TX_OK;
 	}
 
 	macsec_count_tx(skb, &macsec->secy.tx_sc, macsec_skb_cb(skb)->tx_sa);
 
 	macsec_encrypt_finish(skb, dev);
-	len = skb->len;
 	ret = dev_queue_xmit(skb);
 	count_tx(dev, ret, len);
 	return ret;
 }
 
-#define SW_MACSEC_FEATURES \
+#define MACSEC_FEATURES \
 	(NETIF_F_SG | NETIF_F_HIGHDMA | NETIF_F_FRAGLIST)
 
-/* If h/w offloading is enabled, use real device features save for
- *   VLAN_FEATURES - they require additional ops
- *   HW_MACSEC - no reason to report it
- */
-#define REAL_DEV_FEATURES(dev) \
-	((dev)->features & ~(NETIF_F_VLAN_FEATURES | NETIF_F_HW_MACSEC))
-
 static int macsec_dev_init(struct net_device *dev)
 {
 	struct macsec_dev *macsec = macsec_priv(dev);
@@ -3442,12 +3460,8 @@
 		return err;
 	}
 
-	if (macsec_is_offloaded(macsec)) {
-		dev->features = REAL_DEV_FEATURES(real_dev);
-	} else {
-		dev->features = real_dev->features & SW_MACSEC_FEATURES;
-		dev->features |= NETIF_F_LLTX | NETIF_F_GSO_SOFTWARE;
-	}
+	dev->features = real_dev->features & MACSEC_FEATURES;
+	dev->features |= NETIF_F_LLTX | NETIF_F_GSO_SOFTWARE;
 
 	dev->needed_headroom = real_dev->needed_headroom +
 			       MACSEC_NEEDED_HEADROOM;
@@ -3476,10 +3490,7 @@
 	struct macsec_dev *macsec = macsec_priv(dev);
 	struct net_device *real_dev = macsec->real_dev;
 
-	if (macsec_is_offloaded(macsec))
-		return REAL_DEV_FEATURES(real_dev);
-
-	features &= (real_dev->features & SW_MACSEC_FEATURES) |
+	features &= (real_dev->features & MACSEC_FEATURES) |
 		    NETIF_F_GSO_SOFTWARE | NETIF_F_SOFT_FEATURES;
 	features |= NETIF_F_LLTX;
 
@@ -3614,8 +3625,7 @@
 	dev_uc_del(real_dev, dev->dev_addr);
 
 out:
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
-	macsec->secy.sci = dev_to_sci(dev, MACSEC_PORT_ES);
+	eth_hw_addr_set(dev, addr->sa_data);
 
 	/* If h/w offloading is available, propagate to the device */
 	if (macsec_is_offloaded(macsec)) {
@@ -3653,8 +3663,9 @@
 
 	dev_fetch_sw_netstats(s, dev->tstats);
 
-	s->rx_dropped = dev->stats.rx_dropped;
-	s->tx_dropped = dev->stats.tx_dropped;
+	s->rx_dropped = DEV_STATS_READ(dev, rx_dropped);
+	s->tx_dropped = DEV_STATS_READ(dev, tx_dropped);
+	s->rx_errors = DEV_STATS_READ(dev, rx_errors);
 }
 
 static int macsec_get_iflink(const struct net_device *dev)
@@ -3695,6 +3706,7 @@
 	[IFLA_MACSEC_SCB] = { .type = NLA_U8 },
 	[IFLA_MACSEC_REPLAY_PROTECT] = { .type = NLA_U8 },
 	[IFLA_MACSEC_VALIDATION] = { .type = NLA_U8 },
+	[IFLA_MACSEC_OFFLOAD] = { .type = NLA_U8 },
 };
 
 static void macsec_free_netdev(struct net_device *dev)
@@ -3738,9 +3750,6 @@
 		secy->operational = tx_sa && tx_sa->active;
 	}
 
-	if (data[IFLA_MACSEC_WINDOW])
-		secy->replay_window = nla_get_u32(data[IFLA_MACSEC_WINDOW]);
-
 	if (data[IFLA_MACSEC_ENCRYPT])
 		tx_sc->encrypt = !!nla_get_u8(data[IFLA_MACSEC_ENCRYPT]);
 
@@ -3786,6 +3795,16 @@
 		}
 	}
 
+	if (data[IFLA_MACSEC_WINDOW]) {
+		secy->replay_window = nla_get_u32(data[IFLA_MACSEC_WINDOW]);
+
+		/* IEEE 802.1AEbw-2013 10.7.8 - maximum replay window
+		 * for XPN cipher suites */
+		if (secy->xpn &&
+		    secy->replay_window > MACSEC_XPN_MAX_REPLAY_WINDOW)
+			return -EINVAL;
+	}
+
 	return 0;
 }
 
@@ -3815,13 +3834,12 @@
 
 	ret = macsec_changelink_common(dev, data);
 	if (ret)
-		return ret;
+		goto cleanup;
 
 	/* If h/w offloading is available, propagate to the device */
 	if (macsec_is_offloaded(macsec)) {
 		const struct macsec_ops *ops;
 		struct macsec_context ctx;
-		int ret;
 
 		ops = macsec_get_ops(netdev_priv(dev), &ctx);
 		if (!ops) {
@@ -3870,6 +3888,18 @@
 	struct macsec_dev *macsec = macsec_priv(dev);
 	struct net_device *real_dev = macsec->real_dev;
 
+	/* If h/w offloading is available, propagate to the device */
+	if (macsec_is_offloaded(macsec)) {
+		const struct macsec_ops *ops;
+		struct macsec_context ctx;
+
+		ops = macsec_get_ops(netdev_priv(dev), &ctx);
+		if (ops) {
+			ctx.secy = &macsec->secy;
+			macsec_offload(ops->mdo_del_secy, &ctx);
+		}
+	}
+
 	unregister_netdevice_queue(dev, head);
 	list_del_rcu(&macsec->secys);
 	macsec_del_dev(macsec);
@@ -3884,18 +3914,6 @@
 	struct net_device *real_dev = macsec->real_dev;
 	struct macsec_rxh_data *rxd = macsec_data_rtnl(real_dev);
 
-	/* If h/w offloading is available, propagate to the device */
-	if (macsec_is_offloaded(macsec)) {
-		const struct macsec_ops *ops;
-		struct macsec_context ctx;
-
-		ops = macsec_get_ops(netdev_priv(dev), &ctx);
-		if (ops) {
-			ctx.secy = &macsec->secy;
-			macsec_offload(ops->mdo_del_secy, &ctx);
-		}
-	}
-
 	macsec_common_dellink(dev, head);
 
 	if (list_empty(&rxd->secys)) {
@@ -3944,6 +3962,11 @@
 	return false;
 }
 
+static sci_t dev_to_sci(struct net_device *dev, __be16 port)
+{
+	return make_sci(dev->dev_addr, port);
+}
+
 static int macsec_add_dev(struct net_device *dev, sci_t sci, u8 icv_len)
 {
 	struct macsec_dev *macsec = macsec_priv(dev);
@@ -4018,6 +4041,15 @@
 	    !macsec_check_offload(macsec->offload, macsec))
 		return -EOPNOTSUPP;
 
+	/* send_sci must be set to true when transmit sci explicitly is set */
+	if ((data && data[IFLA_MACSEC_SCI]) &&
+	    (data && data[IFLA_MACSEC_INC_SCI])) {
+		u8 send_sci = !!nla_get_u8(data[IFLA_MACSEC_INC_SCI]);
+
+		if (!send_sci)
+			return -EINVAL;
+	}
+
 	if (data && data[IFLA_MACSEC_ICV_LEN])
 		icv_len = nla_get_u8(data[IFLA_MACSEC_ICV_LEN]);
 	mtu = real_dev->mtu - icv_len - macsec_extra_len(true);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/macvlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/macvlan.c
@@ -141,7 +141,7 @@
 	u32 idx = macvlan_eth_hash(addr);
 	struct hlist_head *h = &vlan->port->vlan_source_hash[idx];
 
-	hlist_for_each_entry_rcu(entry, h, hlist) {
+	hlist_for_each_entry_rcu(entry, h, hlist, lockdep_rtnl_is_held()) {
 		if (ether_addr_equal_64bits(entry->addr, addr) &&
 		    entry->vlan == vlan)
 			return entry;
@@ -460,8 +460,10 @@
 			return RX_HANDLER_CONSUMED;
 		*pskb = skb;
 		eth = eth_hdr(skb);
-		if (macvlan_forward_source(skb, port, eth->h_source))
+		if (macvlan_forward_source(skb, port, eth->h_source)) {
+			kfree_skb(skb);
 			return RX_HANDLER_CONSUMED;
+		}
 		src = macvlan_hash_lookup(port, eth->h_source);
 		if (src && src->mode != MACVLAN_MODE_VEPA &&
 		    src->mode != MACVLAN_MODE_BRIDGE) {
@@ -480,8 +482,10 @@
 		return RX_HANDLER_PASS;
 	}
 
-	if (macvlan_forward_source(skb, port, eth->h_source))
+	if (macvlan_forward_source(skb, port, eth->h_source)) {
+		kfree_skb(skb);
 		return RX_HANDLER_CONSUMED;
+	}
 	if (macvlan_passthru(port))
 		vlan = list_first_or_null_rcu(&port->vlans,
 					      struct macvlan_dev, list);
@@ -707,7 +711,7 @@
 
 	if (!(dev->flags & IFF_UP)) {
 		/* Just copy in the new address */
-		ether_addr_copy(dev->dev_addr, addr);
+		eth_hw_addr_set(dev, addr);
 	} else {
 		/* Rehash and update the device filters */
 		if (macvlan_addr_busy(vlan->port, addr))
@@ -766,7 +770,7 @@
 	if (dev->flags & IFF_UP) {
 		if (change & IFF_ALLMULTI)
 			dev_set_allmulti(lowerdev, dev->flags & IFF_ALLMULTI ? 1 : -1);
-		if (change & IFF_PROMISC)
+		if (!macvlan_passthru(vlan->port) && change & IFF_PROMISC)
 			dev_set_promiscuity(lowerdev,
 					    dev->flags & IFF_PROMISC ? 1 : -1);
 
@@ -1177,7 +1181,7 @@
 {
 	ether_setup(dev);
 
-	dev->min_mtu		= 0;
+	/* ether_setup() has set dev->min_mtu to ETH_MIN_MTU. */
 	dev->max_mtu		= ETH_MAX_MTU;
 	dev->priv_flags	       &= ~IFF_TX_SKB_SHARING;
 	netif_keep_dst(dev);
@@ -1517,8 +1521,10 @@
 	/* the macvlan port may be freed by macvlan_uninit when fail to register.
 	 * so we destroy the macvlan port only when it's valid.
 	 */
-	if (create && macvlan_port_get_rtnl(lowerdev))
+	if (create && macvlan_port_get_rtnl(lowerdev)) {
+		macvlan_flush_sources(port, vlan);
 		macvlan_port_destroy(port->dev);
+	}
 	return err;
 }
 EXPORT_SYMBOL_GPL(macvlan_common_newlink);
@@ -1629,7 +1635,7 @@
 	struct hlist_head *h = &vlan->port->vlan_source_hash[i];
 	struct macvlan_source_entry *entry;
 
-	hlist_for_each_entry_rcu(entry, h, hlist) {
+	hlist_for_each_entry_rcu(entry, h, hlist, lockdep_rtnl_is_held()) {
 		if (entry->vlan != vlan)
 			continue;
 		if (nla_put(skb, IFLA_MACVLAN_MACADDR, ETH_ALEN, entry->addr))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/macvtap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/macvtap.c
@@ -133,11 +133,17 @@
 	dev->tx_queue_len = TUN_READQ_SIZE;
 }
 
+static struct net *macvtap_link_net(const struct net_device *dev)
+{
+	return dev_net(macvlan_dev_real_dev(dev));
+}
+
 static struct rtnl_link_ops macvtap_link_ops __read_mostly = {
 	.kind		= "macvtap",
 	.setup		= macvtap_setup,
 	.newlink	= macvtap_newlink,
 	.dellink	= macvtap_dellink,
+	.get_link_net	= macvtap_link_net,
 	.priv_size      = sizeof(struct macvtap_dev),
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/acpi_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/acpi_mdio.c
@@ -18,16 +18,18 @@
 MODULE_LICENSE("GPL");
 
 /**
- * acpi_mdiobus_register - Register mii_bus and create PHYs from the ACPI ASL.
+ * __acpi_mdiobus_register - Register mii_bus and create PHYs from the ACPI ASL.
  * @mdio: pointer to mii_bus structure
  * @fwnode: pointer to fwnode of MDIO bus. This fwnode is expected to represent
+ * @owner: module owning this @mdio object.
  * an ACPI device object corresponding to the MDIO bus and its children are
  * expected to correspond to the PHY devices on that bus.
  *
  * This function registers the mii_bus structure and registers a phy_device
  * for each child node of @fwnode.
  */
-int acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *fwnode)
+int __acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *fwnode,
+			    struct module *owner)
 {
 	struct fwnode_handle *child;
 	u32 addr;
@@ -35,7 +37,7 @@
 
 	/* Mask out all PHYs from auto probing. */
 	mdio->phy_mask = GENMASK(31, 0);
-	ret = mdiobus_register(mdio);
+	ret = __mdiobus_register(mdio, owner);
 	if (ret)
 		return ret;
 
@@ -55,4 +57,4 @@
 	}
 	return 0;
 }
-EXPORT_SYMBOL(acpi_mdiobus_register);
+EXPORT_SYMBOL(__acpi_mdiobus_register);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/fwnode_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/fwnode_mdio.c
@@ -17,6 +17,7 @@
 static struct mii_timestamper *
 fwnode_find_mii_timestamper(struct fwnode_handle *fwnode)
 {
+	struct mii_timestamper *mii_ts;
 	struct of_phandle_args arg;
 	int err;
 
@@ -30,10 +31,16 @@
 	else if (err)
 		return ERR_PTR(err);
 
-	if (arg.args_count != 1)
-		return ERR_PTR(-EINVAL);
+	if (arg.args_count != 1) {
+		mii_ts = ERR_PTR(-EINVAL);
+		goto put_node;
+	}
+
+	mii_ts = register_mii_timestamper(arg.np, arg.args[0]);
 
-	return register_mii_timestamper(arg.np, arg.args[0]);
+put_node:
+	of_node_put(arg.np);
+	return mii_ts;
 }
 
 int fwnode_mdiobus_phy_device_register(struct mii_bus *mdio,
@@ -43,6 +50,11 @@
 	int rc;
 
 	rc = fwnode_irq_get(child, 0);
+	/* Don't wait forever if the IRQ provider doesn't become available,
+	 * just fall back to poll mode
+	 */
+	if (rc == -EPROBE_DEFER)
+		rc = driver_deferred_probe_check_state(&phy->mdio.dev);
 	if (rc == -EPROBE_DEFER)
 		return rc;
 
@@ -72,6 +84,7 @@
 	 */
 	rc = phy_device_register(phy);
 	if (rc) {
+		device_set_node(&phy->mdio.dev, NULL);
 		fwnode_handle_put(child);
 		return rc;
 	}
@@ -105,8 +118,8 @@
 	else
 		phy = phy_device_create(bus, addr, phy_id, 0, NULL);
 	if (IS_ERR(phy)) {
-		unregister_mii_timestamper(mii_ts);
-		return PTR_ERR(phy);
+		rc = PTR_ERR(phy);
+		goto clean_mii_ts;
 	}
 
 	if (is_acpi_node(child)) {
@@ -115,22 +128,19 @@
 		/* Associate the fwnode with the device structure so it
 		 * can be looked up later.
 		 */
-		phy->mdio.dev.fwnode = child;
+		phy->mdio.dev.fwnode = fwnode_handle_get(child);
 
 		/* All data is now stored in the phy struct, so register it */
 		rc = phy_device_register(phy);
 		if (rc) {
-			phy_device_free(phy);
-			fwnode_handle_put(phy->mdio.dev.fwnode);
-			return rc;
+			phy->mdio.dev.fwnode = NULL;
+			fwnode_handle_put(child);
+			goto clean_phy;
 		}
 	} else if (is_of_node(child)) {
 		rc = fwnode_mdiobus_phy_device_register(bus, phy, child, addr);
-		if (rc) {
-			unregister_mii_timestamper(mii_ts);
-			phy_device_free(phy);
-			return rc;
-		}
+		if (rc)
+			goto clean_phy;
 	}
 
 	/* phy->mii_ts may already be defined by the PHY driver. A
@@ -140,5 +150,12 @@
 	if (mii_ts)
 		phy->mii_ts = mii_ts;
 	return 0;
+
+clean_phy:
+	phy_device_free(phy);
+clean_mii_ts:
+	unregister_mii_timestamper(mii_ts);
+
+	return rc;
 }
 EXPORT_SYMBOL(fwnode_mdiobus_register_phy);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-aspeed.c
@@ -61,6 +61,13 @@
 
 	iowrite32(ctrl, ctx->base + ASPEED_MDIO_CTRL);
 
+	rc = readl_poll_timeout(ctx->base + ASPEED_MDIO_CTRL, ctrl,
+				!(ctrl & ASPEED_MDIO_CTRL_FIRE),
+				ASPEED_MDIO_INTERVAL_US,
+				ASPEED_MDIO_TIMEOUT_US);
+	if (rc < 0)
+		return rc;
+
 	rc = readl_poll_timeout(ctx->base + ASPEED_MDIO_DATA, data,
 				data & ASPEED_MDIO_DATA_IDLE,
 				ASPEED_MDIO_INTERVAL_US,
@@ -141,6 +148,7 @@
 	{ .compatible = "aspeed,ast2600-mdio", },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, aspeed_mdio_of_match);
 
 static struct platform_driver aspeed_mdio_driver = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-ipq4019.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-ipq4019.c
@@ -200,7 +200,11 @@
 	if (ret)
 		return ret;
 
-	return clk_prepare_enable(priv->mdio_clk);
+	ret = clk_prepare_enable(priv->mdio_clk);
+	if (ret == 0)
+		mdelay(10);
+
+	return ret;
 }
 
 static int ipq4019_mdio_probe(struct platform_device *pdev)
@@ -227,8 +231,11 @@
 	/* The platform resource is provided on the chipset IPQ5018 */
 	/* This resource is optional */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (res)
+	if (res) {
 		priv->eth_ldo_rdy = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(priv->eth_ldo_rdy))
+			return PTR_ERR(priv->eth_ldo_rdy);
+	}
 
 	bus->name = "ipq4019_mdio";
 	bus->read = ipq4019_mdio_read;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-mscc-miim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-mscc-miim.c
@@ -76,6 +76,9 @@
 	u32 val;
 	int ret;
 
+	if (regnum & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
 	ret = mscc_miim_wait_pending(bus);
 	if (ret)
 		goto out;
@@ -105,6 +108,9 @@
 	struct mscc_miim_dev *miim = bus->priv;
 	int ret;
 
+	if (regnum & MII_ADDR_C45)
+		return -EOPNOTSUPP;
+
 	ret = mscc_miim_wait_pending(bus);
 	if (ret < 0)
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-mux-bcm6368.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-mux-bcm6368.c
@@ -115,7 +115,7 @@
 	md->mii_bus = devm_mdiobus_alloc(&pdev->dev);
 	if (!md->mii_bus) {
 		dev_err(&pdev->dev, "mdiomux bus alloc failed\n");
-		return ENOMEM;
+		return -ENOMEM;
 	}
 
 	bus = md->mii_bus;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-mux-meson-g12a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-mux-meson-g12a.c
@@ -4,6 +4,7 @@
  */
 
 #include <linux/bitfield.h>
+#include <linux/delay.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/device.h>
@@ -150,6 +151,7 @@
 
 static int g12a_enable_internal_mdio(struct g12a_mdio_mux *priv)
 {
+	u32 value;
 	int ret;
 
 	/* Enable the phy clock */
@@ -163,18 +165,25 @@
 
 	/* Initialize ephy control */
 	writel(EPHY_G12A_ID, priv->regs + ETH_PHY_CNTL0);
-	writel(FIELD_PREP(PHY_CNTL1_ST_MODE, 3) |
-	       FIELD_PREP(PHY_CNTL1_ST_PHYADD, EPHY_DFLT_ADD) |
-	       FIELD_PREP(PHY_CNTL1_MII_MODE, EPHY_MODE_RMII) |
-	       PHY_CNTL1_CLK_EN |
-	       PHY_CNTL1_CLKFREQ |
-	       PHY_CNTL1_PHY_ENB,
-	       priv->regs + ETH_PHY_CNTL1);
+
+	/* Make sure we get a 0 -> 1 transition on the enable bit */
+	value = FIELD_PREP(PHY_CNTL1_ST_MODE, 3) |
+		FIELD_PREP(PHY_CNTL1_ST_PHYADD, EPHY_DFLT_ADD) |
+		FIELD_PREP(PHY_CNTL1_MII_MODE, EPHY_MODE_RMII) |
+		PHY_CNTL1_CLK_EN |
+		PHY_CNTL1_CLKFREQ;
+	writel(value, priv->regs + ETH_PHY_CNTL1);
 	writel(PHY_CNTL2_USE_INTERNAL |
 	       PHY_CNTL2_SMI_SRC_MAC |
 	       PHY_CNTL2_RX_CLK_EPHY,
 	       priv->regs + ETH_PHY_CNTL2);
 
+	value |= PHY_CNTL1_PHY_ENB;
+	writel(value, priv->regs + ETH_PHY_CNTL1);
+
+	/* The phy needs a bit of time to power up */
+	mdelay(10);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-mvusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-mvusb.c
@@ -73,6 +73,7 @@
 	struct device *dev = &interface->dev;
 	struct mvusb_mdio *mvusb;
 	struct mii_bus *mdio;
+	int ret;
 
 	mdio = devm_mdiobus_alloc_size(dev, sizeof(*mvusb));
 	if (!mdio)
@@ -93,7 +94,15 @@
 	mdio->write = mvusb_mdio_write;
 
 	usb_set_intfdata(interface, mvusb);
-	return of_mdiobus_register(mdio, dev->of_node);
+	ret = of_mdiobus_register(mdio, dev->of_node);
+	if (ret)
+		goto put_dev;
+
+	return 0;
+
+put_dev:
+	usb_put_dev(mvusb->udev);
+	return ret;
 }
 
 static void mvusb_mdio_disconnect(struct usb_interface *interface)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/mdio-thunder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/mdio-thunder.c
@@ -104,6 +104,7 @@
 		if (i >= ARRAY_SIZE(nexus->buses))
 			break;
 	}
+	fwnode_handle_put(fwn);
 	return 0;
 
 err_release_regions:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mdio/of_mdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mdio/of_mdio.c
@@ -68,8 +68,9 @@
 	/* All data is now stored in the mdiodev struct; register it. */
 	rc = mdio_device_register(mdiodev);
 	if (rc) {
+		device_set_node(&mdiodev->dev, NULL);
+		fwnode_handle_put(fwnode);
 		mdio_device_free(mdiodev);
-		of_node_put(child);
 		return rc;
 	}
 
@@ -138,21 +139,23 @@
 EXPORT_SYMBOL(of_mdiobus_child_is_phy);
 
 /**
- * of_mdiobus_register - Register mii_bus and create PHYs from the device tree
+ * __of_mdiobus_register - Register mii_bus and create PHYs from the device tree
  * @mdio: pointer to mii_bus structure
  * @np: pointer to device_node of MDIO bus.
+ * @owner: module owning the @mdio object.
  *
  * This function registers the mii_bus structure and registers a phy_device
  * for each child node of @np.
  */
-int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np)
+int __of_mdiobus_register(struct mii_bus *mdio, struct device_node *np,
+			  struct module *owner)
 {
 	struct device_node *child;
 	bool scanphys = false;
 	int addr, rc;
 
 	if (!np)
-		return mdiobus_register(mdio);
+		return __mdiobus_register(mdio, owner);
 
 	/* Do not continue if the node is disabled */
 	if (!of_device_is_available(np))
@@ -171,7 +174,7 @@
 	of_property_read_u32(np, "reset-post-delay-us", &mdio->reset_post_delay_us);
 
 	/* Register the MDIO bus */
-	rc = mdiobus_register(mdio);
+	rc = __mdiobus_register(mdio, owner);
 	if (rc)
 		return rc;
 
@@ -231,10 +234,11 @@
 	return 0;
 
 unregister:
+	of_node_put(child);
 	mdiobus_unregister(mdio);
 	return rc;
 }
-EXPORT_SYMBOL(of_mdiobus_register);
+EXPORT_SYMBOL(__of_mdiobus_register);
 
 /**
  * of_mdio_find_device - Given a device tree node, find the mdio_device
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/mhi_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/mhi_net.c
@@ -343,6 +343,8 @@
 
 	kfree_skb(mhi_netdev->skbagg_head);
 
+	free_netdev(ndev);
+
 	dev_set_drvdata(&mhi_dev->dev, NULL);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/net_failover.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/net_failover.c
@@ -130,14 +130,10 @@
 			txq = ops->ndo_select_queue(primary_dev, skb, sb_dev);
 		else
 			txq = netdev_pick_tx(primary_dev, skb, NULL);
-
-		qdisc_skb_cb(skb)->slave_dev_queue_mapping = skb->queue_mapping;
-
-		return txq;
+	} else {
+		txq = skb_rx_queue_recorded(skb) ? skb_get_rx_queue(skb) : 0;
 	}
 
-	txq = skb_rx_queue_recorded(skb) ? skb_get_rx_queue(skb) : 0;
-
 	/* Save the original txq to restore before passing to the driver */
 	qdisc_skb_cb(skb)->slave_dev_queue_mapping = skb->queue_mapping;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netconsole.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netconsole.c
@@ -716,6 +716,7 @@
 				/* rtnl_lock already held
 				 * we might sleep in __netpoll_cleanup()
 				 */
+				nt->enabled = false;
 				spin_unlock_irqrestore(&target_list_lock, flags);
 
 				__netpoll_cleanup(&nt->np);
@@ -723,7 +724,6 @@
 				spin_lock_irqsave(&target_list_lock, flags);
 				dev_put(nt->np.dev);
 				nt->np.dev = NULL;
-				nt->enabled = false;
 				stopped = true;
 				netconsole_target_put(nt);
 				goto restart;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/bpf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/bpf.c
@@ -351,10 +351,12 @@
 {
 	struct nsim_bpf_bound_map *nmap = offmap->dev_priv;
 
-	nmap->entry[idx].key = kmalloc(offmap->map.key_size, GFP_USER);
+	nmap->entry[idx].key = kmalloc(offmap->map.key_size,
+				       GFP_KERNEL_ACCOUNT | __GFP_NOWARN);
 	if (!nmap->entry[idx].key)
 		return -ENOMEM;
-	nmap->entry[idx].value = kmalloc(offmap->map.value_size, GFP_USER);
+	nmap->entry[idx].value = kmalloc(offmap->map.value_size,
+					 GFP_KERNEL_ACCOUNT | __GFP_NOWARN);
 	if (!nmap->entry[idx].value) {
 		kfree(nmap->entry[idx].key);
 		nmap->entry[idx].key = NULL;
@@ -496,7 +498,7 @@
 	if (offmap->map.map_flags)
 		return -EINVAL;
 
-	nmap = kzalloc(sizeof(*nmap), GFP_USER);
+	nmap = kzalloc(sizeof(*nmap), GFP_KERNEL_ACCOUNT);
 	if (!nmap)
 		return -ENOMEM;
 
@@ -514,6 +516,7 @@
 				goto err_free;
 			key = nmap->entry[i].key;
 			*key = i;
+			memset(nmap->entry[i].value, 0, offmap->map.value_size);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/dev.c
@@ -168,13 +168,10 @@
 	cookie_len = (count - 1) / 2;
 	if ((count - 1) % 2)
 		return -EINVAL;
-	buf = kmalloc(count, GFP_KERNEL | __GFP_NOWARN);
-	if (!buf)
-		return -ENOMEM;
 
-	ret = simple_write_to_buffer(buf, count, ppos, data, count);
-	if (ret < 0)
-		goto free_buf;
+	buf = memdup_user(data, count);
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
 
 	fa_cookie = kmalloc(sizeof(*fa_cookie) + cookie_len,
 			    GFP_KERNEL | __GFP_NOWARN);
@@ -229,8 +226,10 @@
 	if (IS_ERR(nsim_dev->ddir))
 		return PTR_ERR(nsim_dev->ddir);
 	nsim_dev->ports_ddir = debugfs_create_dir("ports", nsim_dev->ddir);
-	if (IS_ERR(nsim_dev->ports_ddir))
-		return PTR_ERR(nsim_dev->ports_ddir);
+	if (IS_ERR(nsim_dev->ports_ddir)) {
+		err = PTR_ERR(nsim_dev->ports_ddir);
+		goto err_ddir;
+	}
 	debugfs_create_bool("fw_update_status", 0600, nsim_dev->ddir,
 			    &nsim_dev->fw_update_status);
 	debugfs_create_u32("fw_update_overwrite_mask", 0600, nsim_dev->ddir,
@@ -267,7 +266,7 @@
 	nsim_dev->nodes_ddir = debugfs_create_dir("rate_nodes", nsim_dev->ddir);
 	if (IS_ERR(nsim_dev->nodes_ddir)) {
 		err = PTR_ERR(nsim_dev->nodes_ddir);
-		goto err_out;
+		goto err_ports_ddir;
 	}
 	debugfs_create_bool("fail_trap_drop_counter_get", 0600,
 			    nsim_dev->ddir,
@@ -275,8 +274,9 @@
 	nsim_udp_tunnels_debugfs_create(nsim_dev);
 	return 0;
 
-err_out:
+err_ports_ddir:
 	debugfs_remove_recursive(nsim_dev->ports_ddir);
+err_ddir:
 	debugfs_remove_recursive(nsim_dev->ddir);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/ethtool.c
@@ -77,7 +77,10 @@
 {
 	struct netdevsim *ns = netdev_priv(dev);
 
-	memcpy(&ns->ethtool.ring, ring, sizeof(ns->ethtool.ring));
+	ns->ethtool.ring.rx_pending = ring->rx_pending;
+	ns->ethtool.ring.rx_jumbo_pending = ring->rx_jumbo_pending;
+	ns->ethtool.ring.rx_mini_pending = ring->rx_mini_pending;
+	ns->ethtool.ring.tx_pending = ring->tx_pending;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/fib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/fib.c
@@ -53,6 +53,7 @@
 	struct rhashtable nexthop_ht;
 	struct devlink *devlink;
 	struct work_struct fib_event_work;
+	struct work_struct fib_flush_work;
 	struct list_head fib_event_queue;
 	spinlock_t fib_event_queue_lock; /* Protects fib event queue list */
 	struct mutex nh_lock; /* Protects NH HT */
@@ -623,14 +624,14 @@
 		if (err)
 			goto err_fib6_rt_nh_del;
 
-		fib6_event->rt_arr[i]->trap = true;
+		WRITE_ONCE(fib6_event->rt_arr[i]->trap, true);
 	}
 
 	return 0;
 
 err_fib6_rt_nh_del:
 	for (i--; i >= 0; i--) {
-		fib6_event->rt_arr[i]->trap = false;
+		WRITE_ONCE(fib6_event->rt_arr[i]->trap, false);
 		nsim_fib6_rt_nh_del(fib6_rt, fib6_event->rt_arr[i]);
 	}
 	return err;
@@ -977,7 +978,7 @@
 
 	fib_event = kzalloc(sizeof(*fib_event), GFP_ATOMIC);
 	if (!fib_event)
-		return NOTIFY_BAD;
+		goto err_fib_event_alloc;
 
 	fib_event->data = data;
 	fib_event->event = event;
@@ -1005,6 +1006,9 @@
 
 err_fib_prepare_event:
 	kfree(fib_event);
+err_fib_event_alloc:
+	if (event == FIB_EVENT_ENTRY_DEL)
+		schedule_work(&data->fib_flush_work);
 	return NOTIFY_BAD;
 }
 
@@ -1362,10 +1366,12 @@
 
 	if (pos != 0)
 		return -EINVAL;
-	if (size > sizeof(buf))
+	if (size > sizeof(buf) - 1)
 		return -EINVAL;
 	if (copy_from_user(buf, user_buf, size))
 		return -EFAULT;
+	buf[size] = 0;
+
 	if (sscanf(buf, "%u %hu", &nhid, &bucket_index) != 2)
 		return -EINVAL;
 
@@ -1482,6 +1488,24 @@
 	mutex_unlock(&data->fib_lock);
 }
 
+static void nsim_fib_flush_work(struct work_struct *work)
+{
+	struct nsim_fib_data *data = container_of(work, struct nsim_fib_data,
+						  fib_flush_work);
+	struct nsim_fib_rt *fib_rt, *fib_rt_tmp;
+
+	/* Process pending work. */
+	flush_work(&data->fib_event_work);
+
+	mutex_lock(&data->fib_lock);
+	list_for_each_entry_safe(fib_rt, fib_rt_tmp, &data->fib_rt_list, list) {
+		rhashtable_remove_fast(&data->fib_rt_ht, &fib_rt->ht_node,
+				       nsim_fib_rt_ht_params);
+		nsim_fib_rt_free(fib_rt, data);
+	}
+	mutex_unlock(&data->fib_lock);
+}
+
 static int
 nsim_fib_debugfs_init(struct nsim_fib_data *data, struct nsim_dev *nsim_dev)
 {
@@ -1540,6 +1564,7 @@
 		goto err_rhashtable_nexthop_destroy;
 
 	INIT_WORK(&data->fib_event_work, nsim_fib_event_work);
+	INIT_WORK(&data->fib_flush_work, nsim_fib_flush_work);
 	INIT_LIST_HEAD(&data->fib_event_queue);
 	spin_lock_init(&data->fib_event_queue_lock);
 
@@ -1586,6 +1611,7 @@
 err_nexthop_nb_unregister:
 	unregister_nexthop_notifier(devlink_net(devlink), &data->nexthop_nb);
 err_rhashtable_fib_destroy:
+	cancel_work_sync(&data->fib_flush_work);
 	flush_work(&data->fib_event_work);
 	rhashtable_free_and_destroy(&data->fib_rt_ht, nsim_fib_rt_free,
 				    data);
@@ -1615,6 +1641,7 @@
 					    NSIM_RESOURCE_IPV4_FIB);
 	unregister_fib_notifier(devlink_net(devlink), &data->fib_nb);
 	unregister_nexthop_notifier(devlink_net(devlink), &data->nexthop_nb);
+	cancel_work_sync(&data->fib_flush_work);
 	flush_work(&data->fib_event_work);
 	rhashtable_free_and_destroy(&data->fib_rt_ht, nsim_fib_rt_free,
 				    data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/health.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/health.c
@@ -235,6 +235,8 @@
 	char *break_msg;
 	int err;
 
+	if (count == 0 || count > PAGE_SIZE)
+		return -EINVAL;
 	break_msg = memdup_user_nul(data, count);
 	if (IS_ERR(break_msg))
 		return PTR_ERR(break_msg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/ipsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/ipsec.c
@@ -39,10 +39,14 @@
 		if (!sap->used)
 			continue;
 
-		p += scnprintf(p, bufsize - (p - buf),
-			       "sa[%i] %cx ipaddr=0x%08x %08x %08x %08x\n",
-			       i, (sap->rx ? 'r' : 't'), sap->ipaddr[0],
-			       sap->ipaddr[1], sap->ipaddr[2], sap->ipaddr[3]);
+		if (sap->xs->props.family == AF_INET6)
+			p += scnprintf(p, bufsize - (p - buf),
+				       "sa[%i] %cx ipaddr=%pI6c\n",
+				       i, (sap->rx ? 'r' : 't'), &sap->ipaddr);
+		else
+			p += scnprintf(p, bufsize - (p - buf),
+				       "sa[%i] %cx ipaddr=%pI4\n",
+				       i, (sap->rx ? 'r' : 't'), &sap->ipaddr[3]);
 		p += scnprintf(p, bufsize - (p - buf),
 			       "sa[%i]    spi=0x%08x proto=0x%x salt=0x%08x crypt=%d\n",
 			       i, be32_to_cpu(sap->xs->id.spi),
@@ -171,14 +175,13 @@
 		return ret;
 	}
 
-	if (xs->xso.flags & XFRM_OFFLOAD_INBOUND) {
+	if (xs->xso.dir == XFRM_DEV_OFFLOAD_IN)
 		sa.rx = true;
 
-		if (xs->props.family == AF_INET6)
-			memcpy(sa.ipaddr, &xs->id.daddr.a6, 16);
-		else
-			memcpy(&sa.ipaddr[3], &xs->id.daddr.a4, 4);
-	}
+	if (xs->props.family == AF_INET6)
+		memcpy(sa.ipaddr, &xs->id.daddr.a6, 16);
+	else
+		memcpy(&sa.ipaddr[3], &xs->id.daddr.a4, 4);
 
 	/* the preparations worked, so save the info */
 	memcpy(&ipsec->sa[sa_idx], &sa, sizeof(sa));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/netdev.c
@@ -67,10 +67,10 @@
 	unsigned int start;
 
 	do {
-		start = u64_stats_fetch_begin(&ns->syncp);
+		start = u64_stats_fetch_begin_irq(&ns->syncp);
 		stats->tx_bytes = ns->tx_bytes;
 		stats->tx_packets = ns->tx_packets;
-	} while (u64_stats_fetch_retry(&ns->syncp, start));
+	} while (u64_stats_fetch_retry_irq(&ns->syncp, start));
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/netdevsim.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/netdevsim.h
@@ -97,6 +97,7 @@
 		u32 sleep;
 		u32 __ports[2][NSIM_UDP_TUNNEL_N_PORTS];
 		u32 (*ports)[NSIM_UDP_TUNNEL_N_PORTS];
+		struct dentry *ddir;
 		struct debugfs_u32_array dfs_ports[2];
 	} udp_ports;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/netdevsim/udp_tunnels.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/netdevsim/udp_tunnels.c
@@ -112,9 +112,11 @@
 	struct net_device *dev = file->private_data;
 	struct netdevsim *ns = netdev_priv(dev);
 
-	memset(ns->udp_ports.ports, 0, sizeof(ns->udp_ports.__ports));
 	rtnl_lock();
-	udp_tunnel_nic_reset_ntf(dev);
+	if (dev->reg_state == NETREG_REGISTERED) {
+		memset(ns->udp_ports.ports, 0, sizeof(ns->udp_ports.__ports));
+		udp_tunnel_nic_reset_ntf(dev);
+	}
 	rtnl_unlock();
 
 	return count;
@@ -144,23 +146,23 @@
 	else
 		ns->udp_ports.ports = nsim_dev->udp_ports.__ports;
 
-	debugfs_create_u32("udp_ports_inject_error", 0600,
-			   ns->nsim_dev_port->ddir,
+	ns->udp_ports.ddir = debugfs_create_dir("udp_ports",
+						ns->nsim_dev_port->ddir);
+
+	debugfs_create_u32("inject_error", 0600, ns->udp_ports.ddir,
 			   &ns->udp_ports.inject_error);
 
 	ns->udp_ports.dfs_ports[0].array = ns->udp_ports.ports[0];
 	ns->udp_ports.dfs_ports[0].n_elements = NSIM_UDP_TUNNEL_N_PORTS;
-	debugfs_create_u32_array("udp_ports_table0", 0400,
-				 ns->nsim_dev_port->ddir,
+	debugfs_create_u32_array("table0", 0400, ns->udp_ports.ddir,
 				 &ns->udp_ports.dfs_ports[0]);
 
 	ns->udp_ports.dfs_ports[1].array = ns->udp_ports.ports[1];
 	ns->udp_ports.dfs_ports[1].n_elements = NSIM_UDP_TUNNEL_N_PORTS;
-	debugfs_create_u32_array("udp_ports_table1", 0400,
-				 ns->nsim_dev_port->ddir,
+	debugfs_create_u32_array("table1", 0400, ns->udp_ports.ddir,
 				 &ns->udp_ports.dfs_ports[1]);
 
-	debugfs_create_file("udp_ports_reset", 0200, ns->nsim_dev_port->ddir,
+	debugfs_create_file("reset", 0200, ns->udp_ports.ddir,
 			    dev, &nsim_udp_tunnels_info_reset_fops);
 
 	/* Note: it's not normal to allocate the info struct like this!
@@ -196,6 +198,9 @@
 
 void nsim_udp_tunnels_info_destroy(struct net_device *dev)
 {
+	struct netdevsim *ns = netdev_priv(dev);
+
+	debugfs_remove_recursive(ns->udp_ports.ddir);
 	kfree(dev->udp_tunnel_nic_info);
 	dev->udp_tunnel_nic_info = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ntb_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ntb_netdev.c
@@ -137,7 +137,7 @@
 enqueue_again:
 	rc = ntb_transport_rx_enqueue(qp, skb, skb->data, ndev->mtu + ETH_HLEN);
 	if (rc) {
-		dev_kfree_skb(skb);
+		dev_kfree_skb_any(skb);
 		ndev->stats.rx_errors++;
 		ndev->stats.rx_fifo_errors++;
 	}
@@ -192,7 +192,7 @@
 		ndev->stats.tx_aborted_errors++;
 	}
 
-	dev_kfree_skb(skb);
+	dev_kfree_skb_any(skb);
 
 	if (ntb_transport_tx_free_entry(dev->qp) >= tx_start) {
 		/* Make sure anybody stopping the queue after this sees the new
@@ -484,7 +484,14 @@
 	rc = ntb_transport_register_client_dev(KBUILD_MODNAME);
 	if (rc)
 		return rc;
-	return ntb_transport_register_client(&ntb_netdev_client);
+
+	rc = ntb_transport_register_client(&ntb_netdev_client);
+	if (rc) {
+		ntb_transport_unregister_client_dev(KBUILD_MODNAME);
+		return rc;
+	}
+
+	return 0;
 }
 module_init(ntb_netdev_init_module);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/pcs/pcs-xpcs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/pcs/pcs-xpcs.c
@@ -242,7 +242,7 @@
 		dev = MDIO_MMD_VEND2;
 		break;
 	default:
-		return -1;
+		return -EINVAL;
 	}
 
 	ret = xpcs_write(xpcs, dev, MDIO_CTRL1, MDIO_CTRL1_RESET);
@@ -309,7 +309,7 @@
 	return 0;
 }
 
-static int xpcs_read_link_c73(struct dw_xpcs *xpcs, bool an)
+static int xpcs_read_link_c73(struct dw_xpcs *xpcs)
 {
 	bool link = true;
 	int ret;
@@ -321,15 +321,6 @@
 	if (!(ret & MDIO_STAT1_LSTATUS))
 		link = false;
 
-	if (an) {
-		ret = xpcs_read(xpcs, MDIO_MMD_AN, MDIO_STAT1);
-		if (ret < 0)
-			return ret;
-
-		if (!(ret & MDIO_STAT1_LSTATUS))
-			link = false;
-	}
-
 	return link;
 }
 
@@ -817,7 +808,7 @@
 			return ret;
 		break;
 	default:
-		return -1;
+		return -EINVAL;
 	}
 
 	if (compat->pma_config) {
@@ -847,7 +838,7 @@
 	int ret;
 
 	/* Link needs to be read first ... */
-	state->link = xpcs_read_link_c73(xpcs, state->an_enabled) > 0 ? 1 : 0;
+	state->link = xpcs_read_link_c73(xpcs) > 0 ? 1 : 0;
 
 	/* ... and then we check the faults. */
 	ret = xpcs_read_fault_c73(xpcs, state);
@@ -890,7 +881,7 @@
 	 */
 	ret = xpcs_read(xpcs, MDIO_MMD_VEND2, DW_VR_MII_AN_INTR_STS);
 	if (ret < 0)
-		return false;
+		return ret;
 
 	if (ret & DW_VR_MII_C37_ANSGM_SP_LNKSTS) {
 		int speed_value;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/Kconfig
@@ -239,7 +239,8 @@
 	depends on PTP_1588_CLOCK_OPTIONAL || !NETWORK_PHY_TIMESTAMPING
 	select CRYPTO_LIB_AES if MACSEC
 	help
-	  Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
+	  Currently supports VSC8514, VSC8530, VSC8531, VSC8531_02, VSC8540 and
+	  VSC8541 PHYs
 
 config MOTORCOMM_PHY
 	tristate "Motorcomm PHYs"
@@ -339,6 +340,14 @@
 	help
 	  Currently supports the vsc8244
 
+config XILINX_PHY
+	tristate "Drivers for xilinx PHYs"
+	help
+	  This module provides a driver for the Xilinx PCS/PMA Core.
+	  The supported PHY modes include SGMII and 1000BaseX.
+	  This can be used an Ethernet controller, for example Xilinx
+	  Axi Ethernet or Cadence GEM in Xilinx devices.
+
 config XILINX_GMII2RGMII
 	tristate "Xilinx GMII2RGMII converter driver"
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/Makefile
@@ -84,4 +84,5 @@
 obj-$(CONFIG_STE10XP)		+= ste10Xp.o
 obj-$(CONFIG_TERANETICS_PHY)	+= teranetics.o
 obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
+obj-$(CONFIG_XILINX_PHY)	+= xilinx_phy.o
 obj-$(CONFIG_XILINX_GMII2RGMII) += xilinx_gmii2rgmii.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/aquantia_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/aquantia_main.c
@@ -34,6 +34,8 @@
 #define MDIO_AN_VEND_PROV			0xc400
 #define MDIO_AN_VEND_PROV_1000BASET_FULL	BIT(15)
 #define MDIO_AN_VEND_PROV_1000BASET_HALF	BIT(14)
+#define MDIO_AN_VEND_PROV_5000BASET_FULL	BIT(11)
+#define MDIO_AN_VEND_PROV_2500BASET_FULL	BIT(10)
 #define MDIO_AN_VEND_PROV_DOWNSHIFT_EN		BIT(4)
 #define MDIO_AN_VEND_PROV_DOWNSHIFT_MASK	GENMASK(3, 0)
 #define MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT	4
@@ -88,6 +90,9 @@
 #define VEND1_GLOBAL_FW_ID_MAJOR		GENMASK(15, 8)
 #define VEND1_GLOBAL_FW_ID_MINOR		GENMASK(7, 0)
 
+#define VEND1_GLOBAL_GEN_STAT2			0xc831
+#define VEND1_GLOBAL_GEN_STAT2_OP_IN_PROG	BIT(15)
+
 #define VEND1_GLOBAL_RSVD_STAT1			0xc885
 #define VEND1_GLOBAL_RSVD_STAT1_FW_BUILD_ID	GENMASK(7, 4)
 #define VEND1_GLOBAL_RSVD_STAT1_PROV_ID		GENMASK(3, 0)
@@ -122,6 +127,12 @@
 #define VEND1_GLOBAL_INT_VEND_MASK_GLOBAL2	BIT(1)
 #define VEND1_GLOBAL_INT_VEND_MASK_GLOBAL3	BIT(0)
 
+/* Sleep and timeout for checking if the Processor-Intensive
+ * MDIO operation is finished
+ */
+#define AQR107_OP_IN_PROG_SLEEP		1000
+#define AQR107_OP_IN_PROG_TIMEOUT	100000
+
 struct aqr107_hw_stat {
 	const char *name;
 	int reg;
@@ -231,9 +242,20 @@
 			      phydev->advertising))
 		reg |= MDIO_AN_VEND_PROV_1000BASET_HALF;
 
+	/* Handle the case when the 2.5G and 5G speeds are not advertised */
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT,
+			      phydev->advertising))
+		reg |= MDIO_AN_VEND_PROV_2500BASET_FULL;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT,
+			      phydev->advertising))
+		reg |= MDIO_AN_VEND_PROV_5000BASET_FULL;
+
 	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_VEND_PROV,
 				     MDIO_AN_VEND_PROV_1000BASET_HALF |
-				     MDIO_AN_VEND_PROV_1000BASET_FULL, reg);
+				     MDIO_AN_VEND_PROV_1000BASET_FULL |
+				     MDIO_AN_VEND_PROV_2500BASET_FULL |
+				     MDIO_AN_VEND_PROV_5000BASET_FULL, reg);
 	if (ret < 0)
 		return ret;
 	if (ret > 0)
@@ -585,16 +607,52 @@
 		phydev_info(phydev, "Aquantia 1000Base-T2 mode active\n");
 }
 
+static int aqr107_wait_processor_intensive_op(struct phy_device *phydev)
+{
+	int val, err;
+
+	/* The datasheet notes to wait at least 1ms after issuing a
+	 * processor intensive operation before checking.
+	 * We cannot use the 'sleep_before_read' parameter of read_poll_timeout
+	 * because that just determines the maximum time slept, not the minimum.
+	 */
+	usleep_range(1000, 5000);
+
+	err = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1,
+					VEND1_GLOBAL_GEN_STAT2, val,
+					!(val & VEND1_GLOBAL_GEN_STAT2_OP_IN_PROG),
+					AQR107_OP_IN_PROG_SLEEP,
+					AQR107_OP_IN_PROG_TIMEOUT, false);
+	if (err) {
+		phydev_err(phydev, "timeout: processor-intensive MDIO operation\n");
+		return err;
+	}
+
+	return 0;
+}
+
 static int aqr107_suspend(struct phy_device *phydev)
 {
-	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1,
-				MDIO_CTRL1_LPOWER);
+	int err;
+
+	err = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1,
+			       MDIO_CTRL1_LPOWER);
+	if (err)
+		return err;
+
+	return aqr107_wait_processor_intensive_op(phydev);
 }
 
 static int aqr107_resume(struct phy_device *phydev)
 {
-	return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1,
-				  MDIO_CTRL1_LPOWER);
+	int err;
+
+	err = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1,
+				 MDIO_CTRL1_LPOWER);
+	if (err)
+		return err;
+
+	return aqr107_wait_processor_intensive_op(phydev);
 }
 
 static int aqr107_probe(struct phy_device *phydev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/at803x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/at803x.c
@@ -666,25 +666,7 @@
 			return ret;
 	}
 
-	/* Some bootloaders leave the fiber page selected.
-	 * Switch to the copper page, as otherwise we read
-	 * the PHY capabilities from the fiber side.
-	 */
-	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-		phy_lock_mdio_bus(phydev);
-		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
-		phy_unlock_mdio_bus(phydev);
-		if (ret)
-			goto err;
-	}
-
 	return 0;
-
-err:
-	if (priv->vddio)
-		regulator_disable(priv->vddio);
-
-	return ret;
 }
 
 static void at803x_remove(struct phy_device *phydev)
@@ -785,6 +767,22 @@
 {
 	int ret;
 
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+		/* Some bootloaders leave the fiber page selected.
+		 * Switch to the copper page, as otherwise we read
+		 * the PHY capabilities from the fiber side.
+		 */
+		phy_lock_mdio_bus(phydev);
+		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
+		phy_unlock_mdio_bus(phydev);
+		if (ret)
+			return ret;
+
+		ret = at8031_pll_config(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
 	/* The RX and TX delay default is:
 	 *   after HW reset: RX delay enabled and TX delay disabled
 	 *   after SW reset: RX delay enabled, while TX delay retains the
@@ -814,12 +812,6 @@
 	if (ret < 0)
 		return ret;
 
-	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-		ret = at8031_pll_config(phydev);
-		if (ret < 0)
-			return ret;
-	}
-
 	/* Ar803x extended next page bit is enabled by default. Cisco
 	 * multigig switches read this bit and attempt to negotiate 10Gbps
 	 * rates even if the next page bit is disabled. This is incorrect
@@ -1383,8 +1375,6 @@
 	.flags			= PHY_POLL_CABLE_TEST,
 	.config_init		= at803x_config_init,
 	.link_change_notify	= at803x_link_change_notify,
-	.set_wol		= at803x_set_wol,
-	.get_wol		= at803x_get_wol,
 	.suspend		= at803x_suspend,
 	.resume			= at803x_resume,
 	/* PHY_BASIC_FEATURES */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/ax88796b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/ax88796b.c
@@ -88,8 +88,10 @@
 	/* Reset PHY, otherwise MII_LPA will provide outdated information.
 	 * This issue is reproducible only with some link partner PHYs
 	 */
-	if (phydev->state == PHY_NOLINK && phydev->drv->soft_reset)
-		phydev->drv->soft_reset(phydev);
+	if (phydev->state == PHY_NOLINK) {
+		phy_init_hw(phydev);
+		phy_start_aneg(phydev);
+	}
 }
 
 static struct phy_driver asix_driver[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/bcm84881.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/bcm84881.c
@@ -120,7 +120,7 @@
 
 	bmsr = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_C22 + MII_BMSR);
 	if (bmsr < 0)
-		return val;
+		return bmsr;
 
 	return !!(val & MDIO_AN_STAT1_COMPLETE) &&
 	       !!(bmsr & BMSR_ANEGCOMPLETE);
@@ -146,7 +146,7 @@
 
 	bmsr = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_C22 + MII_BMSR);
 	if (bmsr < 0)
-		return val;
+		return bmsr;
 
 	phydev->autoneg_complete = !!(val & MDIO_AN_STAT1_COMPLETE) &&
 				   !!(bmsr & BMSR_ANEGCOMPLETE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/broadcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/broadcom.c
@@ -11,6 +11,7 @@
  */
 
 #include "bcm-phy-lib.h"
+#include <linux/delay.h>
 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/brcmphy.h>
@@ -411,6 +412,17 @@
 	return bcm54xx_config_init(phydev);
 }
 
+static int bcm54810_read_mmd(struct phy_device *phydev, int devnum, u16 regnum)
+{
+	return -EOPNOTSUPP;
+}
+
+static int bcm54810_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
+			      u16 val)
+{
+	return -EOPNOTSUPP;
+}
+
 static int bcm54811_config_init(struct phy_device *phydev)
 {
 	int err, reg;
@@ -553,6 +565,26 @@
 	if (err < 0)
 		return err;
 
+	/* The datasheet indicates the PHY needs up to 1us to complete a reset,
+	 * build some slack here.
+	 */
+	usleep_range(1000, 2000);
+
+	/* The PHY requires 65 MDC clock cycles to complete a write operation
+	 * and turnaround the line properly.
+	 *
+	 * We ignore -EIO here as the MDIO controller (e.g.: mdio-bcm-unimac)
+	 * may flag the lack of turn-around as a read failure. This is
+	 * particularly true with this combination since the MDIO controller
+	 * only used 64 MDC cycles. This is not a critical failure in this
+	 * specific case and it has no functional impact otherwise, so we let
+	 * that one go through. If there is a genuine bus error, the next read
+	 * of MII_BRCM_FET_INTREG will error out.
+	 */
+	err = phy_read(phydev, MII_BMCR);
+	if (err < 0 && err != -EIO)
+		return err;
+
 	reg = phy_read(phydev, MII_BRCM_FET_INTREG);
 	if (reg < 0)
 		return reg;
@@ -768,6 +800,7 @@
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM54616S",
 	/* PHY_GBIT_FEATURES */
+	.soft_reset     = genphy_soft_reset,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= bcm54616s_config_aneg,
 	.config_intr	= bcm_phy_config_intr,
@@ -810,6 +843,8 @@
 	.get_strings	= bcm_phy_get_strings,
 	.get_stats	= bcm54xx_get_stats,
 	.probe		= bcm54xx_phy_probe,
+	.read_mmd	= bcm54810_read_mmd,
+	.write_mmd	= bcm54810_write_mmd,
 	.config_init    = bcm54xx_config_init,
 	.config_aneg    = bcm5481_config_aneg,
 	.config_intr    = bcm_phy_config_intr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/dp83822.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/dp83822.c
@@ -40,8 +40,8 @@
 /* Control Register 2 bits */
 #define DP83822_FX_ENABLE	BIT(14)
 
-#define DP83822_HW_RESET	BIT(15)
-#define DP83822_SW_RESET	BIT(14)
+#define DP83822_SW_RESET	BIT(15)
+#define DP83822_DIG_RESTART	BIT(14)
 
 /* PHY STS bits */
 #define DP83822_PHYSTS_DUPLEX			BIT(2)
@@ -94,7 +94,8 @@
 #define DP83822_WOL_INDICATION_SEL BIT(8)
 #define DP83822_WOL_CLR_INDICATION BIT(11)
 
-/* RSCR bits */
+/* RCSR bits */
+#define DP83822_RGMII_MODE_EN	BIT(9)
 #define DP83822_RX_CLK_SHIFT	BIT(12)
 #define DP83822_TX_CLK_SHIFT	BIT(11)
 
@@ -228,13 +229,12 @@
 		if (misr_status < 0)
 			return misr_status;
 
-		misr_status |= (DP83822_RX_ERR_HF_INT_EN |
-				DP83822_FALSE_CARRIER_HF_INT_EN |
-				DP83822_LINK_STAT_INT_EN |
+		misr_status |= (DP83822_LINK_STAT_INT_EN |
 				DP83822_ENERGY_DET_INT_EN |
 				DP83822_LINK_QUAL_INT_EN);
 
-		if (!dp83822->fx_enabled)
+		/* Private data pointer is NULL on DP83825/26 */
+		if (!dp83822 || !dp83822->fx_enabled)
 			misr_status |= DP83822_ANEG_COMPLETE_INT_EN |
 				       DP83822_DUP_MODE_CHANGE_INT_EN |
 				       DP83822_SPEED_CHANGED_INT_EN;
@@ -254,9 +254,9 @@
 				DP83822_PAGE_RX_INT_EN |
 				DP83822_EEE_ERROR_CHANGE_INT_EN);
 
-		if (!dp83822->fx_enabled)
-			misr_status |= DP83822_MDI_XOVER_INT_EN |
-				       DP83822_ANEG_ERR_INT_EN |
+		/* Private data pointer is NULL on DP83825/26 */
+		if (!dp83822 || !dp83822->fx_enabled)
+			misr_status |= DP83822_ANEG_ERR_INT_EN |
 				       DP83822_WOL_PKT_INT_EN;
 
 		err = phy_write(phydev, MII_DP83822_MISR2, misr_status);
@@ -274,7 +274,7 @@
 		if (err < 0)
 			return err;
 
-		err = phy_write(phydev, MII_DP83822_MISR1, 0);
+		err = phy_write(phydev, MII_DP83822_MISR2, 0);
 		if (err < 0)
 			return err;
 
@@ -380,7 +380,7 @@
 {
 	struct dp83822_private *dp83822 = phydev->priv;
 	struct device *dev = &phydev->mdio.dev;
-	int rgmii_delay;
+	int rgmii_delay = 0;
 	s32 rx_int_delay;
 	s32 tx_int_delay;
 	int err = 0;
@@ -390,24 +390,33 @@
 		rx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0,
 						      true);
 
-		if (rx_int_delay <= 0)
-			rgmii_delay = 0;
-		else
-			rgmii_delay = DP83822_RX_CLK_SHIFT;
+		/* Set DP83822_RX_CLK_SHIFT to enable rx clk internal delay */
+		if (rx_int_delay > 0)
+			rgmii_delay |= DP83822_RX_CLK_SHIFT;
 
 		tx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0,
 						      false);
+
+		/* Set DP83822_TX_CLK_SHIFT to disable tx clk internal delay */
 		if (tx_int_delay <= 0)
-			rgmii_delay &= ~DP83822_TX_CLK_SHIFT;
-		else
 			rgmii_delay |= DP83822_TX_CLK_SHIFT;
 
-		if (rgmii_delay) {
-			err = phy_set_bits_mmd(phydev, DP83822_DEVADDR,
-					       MII_DP83822_RCSR, rgmii_delay);
-			if (err)
-				return err;
-		}
+		err = phy_modify_mmd(phydev, DP83822_DEVADDR, MII_DP83822_RCSR,
+				     DP83822_RX_CLK_SHIFT | DP83822_TX_CLK_SHIFT, rgmii_delay);
+		if (err)
+			return err;
+
+		err = phy_set_bits_mmd(phydev, DP83822_DEVADDR,
+				       MII_DP83822_RCSR, DP83822_RGMII_MODE_EN);
+
+		if (err)
+			return err;
+	} else {
+		err = phy_clear_bits_mmd(phydev, DP83822_DEVADDR,
+					 MII_DP83822_RCSR, DP83822_RGMII_MODE_EN);
+
+		if (err)
+			return err;
 	}
 
 	if (dp83822->fx_enabled) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/dp83848.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/dp83848.c
@@ -147,6 +147,8 @@
 		/* IRQ related */				\
 		.config_intr	= dp83848_config_intr,		\
 		.handle_interrupt = dp83848_handle_interrupt,	\
+								\
+		.flags		= PHY_RST_AFTER_CLK_EN,		\
 	}
 
 static struct phy_driver dp83848_driver[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/dp83867.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/dp83867.c
@@ -25,6 +25,7 @@
 #define MII_DP83867_MICR	0x12
 #define MII_DP83867_ISR		0x13
 #define DP83867_CFG2		0x14
+#define MII_DP83867_BISCR	0x16
 #define DP83867_CFG3		0x1e
 #define DP83867_CTRL		0x1f
 
@@ -41,6 +42,7 @@
 #define DP83867_STRAP_STS1	0x006E
 #define DP83867_STRAP_STS2	0x006f
 #define DP83867_RGMIIDCTL	0x0086
+#define DP83867_DSP_FFE_CFG	0x012c
 #define DP83867_RXFCFG		0x0134
 #define DP83867_RXFPMD1	0x0136
 #define DP83867_RXFPMD2	0x0137
@@ -103,6 +105,11 @@
 #define DP83867_PHYCR_RX_FIFO_DEPTH_MASK	GENMASK(13, 12)
 #define DP83867_PHYCR_RESERVED_MASK		BIT(11)
 #define DP83867_PHYCR_FORCE_LINK_GOOD		BIT(10)
+#define DP83867_MDI_CROSSOVER		5
+#define DP83867_MDI_CROSSOVER_AUTO		0b10
+#define DP83867_PHYCTRL_SGMIIEN			0x0800
+#define DP83867_PHYCTRL_RXFIFO_SHIFT		12
+#define DP83867_PHYCTRL_TXFIFO_SHIFT		14
 
 /* RGMIIDCTL bits */
 #define DP83867_RGMII_TX_CLK_DELAY_MAX		0xf
@@ -137,11 +144,20 @@
 #define DP83867_DOWNSHIFT_2_COUNT	2
 #define DP83867_DOWNSHIFT_4_COUNT	4
 #define DP83867_DOWNSHIFT_8_COUNT	8
+#define DP83867_SGMII_AUTONEG_EN	BIT(7)
 
 /* CFG3 bits */
 #define DP83867_CFG3_INT_OE			BIT(7)
 #define DP83867_CFG3_ROBUST_AUTO_MDIX		BIT(9)
 
+/* CFG2 bits */
+#define MII_DP83867_CFG2_SPEEDOPT_10EN		0x0040
+#define MII_DP83867_CFG2_SGMII_AUTONEGEN	0x0080
+#define MII_DP83867_CFG2_SPEEDOPT_ENH		0x0100
+#define MII_DP83867_CFG2_SPEEDOPT_CNT		0x0800
+#define MII_DP83867_CFG2_SPEEDOPT_INTLOW	0x2000
+#define MII_DP83867_CFG2_MASK			0x003F
+
 /* CFG4 bits */
 #define DP83867_CFG4_PORT_MIRROR_EN              BIT(0)
 
@@ -641,7 +657,7 @@
 {
 	struct dp83867_private *dp83867 = phydev->priv;
 	int ret, val, bs;
-	u16 delay;
+	u16 delay, cfg2;
 
 	/* Force speed optimization for the PHY even if it strapped */
 	ret = phy_modify(phydev, DP83867_CFG2, DP83867_DOWNSHIFT_EN,
@@ -790,6 +806,35 @@
 		else
 			val &= ~DP83867_SGMII_TYPE;
 		phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_SGMIICTL, val);
+
+		phy_write(phydev, MII_BMCR,
+			  (BMCR_ANENABLE | BMCR_FULLDPLX | BMCR_SPEED1000));
+
+		cfg2 = phy_read(phydev, DP83867_CFG2);
+		cfg2 &= MII_DP83867_CFG2_MASK;
+		cfg2 |= (MII_DP83867_CFG2_SPEEDOPT_10EN |
+			 MII_DP83867_CFG2_SGMII_AUTONEGEN |
+			 MII_DP83867_CFG2_SPEEDOPT_ENH |
+			 MII_DP83867_CFG2_SPEEDOPT_CNT |
+			 MII_DP83867_CFG2_SPEEDOPT_INTLOW);
+		phy_write(phydev, DP83867_CFG2, cfg2);
+
+		phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIICTL, 0x0);
+
+		phy_write(phydev, MII_DP83867_PHYCTRL,
+			  DP83867_PHYCTRL_SGMIIEN |
+			  (DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |
+			  (dp83867->rx_fifo_depth << DP83867_PHYCTRL_RXFIFO_SHIFT) |
+			  (dp83867->tx_fifo_depth  << DP83867_PHYCTRL_TXFIFO_SHIFT));
+		phy_write(phydev, MII_DP83867_BISCR, 0x0);
+
+		/* This is a SW workaround for link instability if RX_CTRL is
+		 * not strapped to mode 3 or 4 in HW. This is required for SGMII
+		 * in addition to clearing bit 7, handled above.
+		 */
+		if (dp83867->rxctrl_strap_quirk)
+			phy_set_bits_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4,
+					 BIT(8));
 	}
 
 	val = phy_read(phydev, DP83867_CFG3);
@@ -826,14 +871,59 @@
 {
 	int err;
 
-	err = phy_write(phydev, DP83867_CTRL, DP83867_SW_RESTART);
+	err = phy_write(phydev, DP83867_CTRL, DP83867_SW_RESET);
 	if (err < 0)
 		return err;
 
 	usleep_range(10, 20);
 
-	return phy_modify(phydev, MII_DP83867_PHYCTRL,
+	err = phy_modify(phydev, MII_DP83867_PHYCTRL,
 			 DP83867_PHYCR_FORCE_LINK_GOOD, 0);
+	if (err < 0)
+		return err;
+
+	/* Configure the DSP Feedforward Equalizer Configuration register to
+	 * improve short cable (< 1 meter) performance. This will not affect
+	 * long cable performance.
+	 */
+	err = phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_DSP_FFE_CFG,
+			    0x0e81);
+	if (err < 0)
+		return err;
+
+	err = phy_write(phydev, DP83867_CTRL, DP83867_SW_RESTART);
+	if (err < 0)
+		return err;
+
+	usleep_range(10, 20);
+
+	return 0;
+}
+
+static void dp83867_link_change_notify(struct phy_device *phydev)
+{
+	/* There is a limitation in DP83867 PHY device where SGMII AN is
+	 * only triggered once after the device is booted up. Even after the
+	 * PHY TPI is down and up again, SGMII AN is not triggered and
+	 * hence no new in-band message from PHY to MAC side SGMII.
+	 * This could cause an issue during power up, when PHY is up prior
+	 * to MAC. At this condition, once MAC side SGMII is up, MAC side
+	 * SGMII wouldn`t receive new in-band message from TI PHY with
+	 * correct link status, speed and duplex info.
+	 * Thus, implemented a SW solution here to retrigger SGMII Auto-Neg
+	 * whenever there is a link change.
+	 */
+	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+		int val = 0;
+
+		val = phy_clear_bits(phydev, DP83867_CFG2,
+				     DP83867_SGMII_AUTONEG_EN);
+		if (val < 0)
+			return;
+
+		phy_set_bits(phydev, DP83867_CFG2,
+			     DP83867_SGMII_AUTONEG_EN);
+	}
 }
 
 static struct phy_driver dp83867_driver[] = {
@@ -860,6 +950,8 @@
 
 		.suspend	= genphy_suspend,
 		.resume		= genphy_resume,
+
+		.link_change_notify = dp83867_link_change_notify,
 	},
 };
 module_phy_driver(dp83867_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/dp83869.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/dp83869.c
@@ -587,15 +587,13 @@
 						       &dp83869_internal_delay[0],
 						       delay_size, true);
 	if (dp83869->rx_int_delay < 0)
-		dp83869->rx_int_delay =
-				dp83869_internal_delay[DP83869_CLK_DELAY_DEF];
+		dp83869->rx_int_delay = DP83869_CLK_DELAY_DEF;
 
 	dp83869->tx_int_delay = phy_get_internal_delay(phydev, dev,
 						       &dp83869_internal_delay[0],
 						       delay_size, false);
 	if (dp83869->tx_int_delay < 0)
-		dp83869->tx_int_delay =
-				dp83869_internal_delay[DP83869_CLK_DELAY_DEF];
+		dp83869->tx_int_delay = DP83869_CLK_DELAY_DEF;
 
 	return ret;
 }
@@ -646,7 +644,6 @@
 		     phydev->supported);
 
 	linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
-	linkmode_set_bit(ADVERTISED_FIBRE, phydev->advertising);
 
 	if (dp83869->mode == DP83869_RGMII_1000_BASE) {
 		linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/marvell.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/marvell.c
@@ -189,6 +189,8 @@
 #define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII	0x4
 #define MII_88E1510_GEN_CTRL_REG_1_RESET	0x8000	/* Soft reset */
 
+#define MII_88E1510_MSCR_2		0x15
+
 #define MII_VCT5_TX_RX_MDI0_COUPLING	0x10
 #define MII_VCT5_TX_RX_MDI1_COUPLING	0x11
 #define MII_VCT5_TX_RX_MDI2_COUPLING	0x12
@@ -551,9 +553,9 @@
 	else
 		mscr = 0;
 
-	return phy_modify_paged(phydev, MII_MARVELL_MSCR_PAGE,
-				MII_88E1121_PHY_MSCR_REG,
-				MII_88E1121_PHY_MSCR_DELAY_MASK, mscr);
+	return phy_modify_paged_changed(phydev, MII_MARVELL_MSCR_PAGE,
+					MII_88E1121_PHY_MSCR_REG,
+					MII_88E1121_PHY_MSCR_DELAY_MASK, mscr);
 }
 
 static int m88e1121_config_aneg(struct phy_device *phydev)
@@ -567,11 +569,13 @@
 			return err;
 	}
 
+	changed = err;
+
 	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);
 	if (err < 0)
 		return err;
 
-	changed = err;
+	changed |= err;
 
 	err = genphy_config_aneg(phydev);
 	if (err < 0)
@@ -1211,16 +1215,15 @@
 {
 	int err;
 
-	err = genphy_soft_reset(phydev);
+	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);
 	if (err < 0)
 		return err;
 
-	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);
+	err = genphy_config_aneg(phydev);
 	if (err < 0)
 		return err;
 
-	err = genphy_config_aneg(phydev);
-	return 0;
+	return genphy_soft_reset(phydev);
 }
 
 static int m88e1118_config_init(struct phy_device *phydev)
@@ -1242,6 +1245,12 @@
 	if (err < 0)
 		return err;
 
+	if (phy_interface_is_rgmii(phydev)) {
+		err = m88e1121_config_aneg_rgmii_delays(phydev);
+		if (err < 0)
+			return err;
+	}
+
 	/* Adjust LED Control */
 	if (phydev->dev_flags & MARVELL_PHY_M1118_DNS323_LEDS)
 		err = phy_write(phydev, 0x10, 0x1100);
@@ -1684,8 +1693,8 @@
 	int err;
 
 	/* Suspend the fiber mode first */
-	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
-			       phydev->supported)) {
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
+			      phydev->supported)) {
 		err = marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE);
 		if (err < 0)
 			goto error;
@@ -1719,8 +1728,8 @@
 	int err;
 
 	/* Resume the fiber mode first */
-	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
-			       phydev->supported)) {
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
+			      phydev->supported)) {
 		err = marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE);
 		if (err < 0)
 			goto error;
@@ -1932,6 +1941,60 @@
 		data[i] = marvell_get_stat(phydev, i);
 }
 
+static int m88e1510_loopback(struct phy_device *phydev, bool enable)
+{
+	int err;
+
+	if (enable) {
+		u16 bmcr_ctl = 0, mscr2_ctl = 0;
+
+		if (phydev->speed == SPEED_1000)
+			bmcr_ctl = BMCR_SPEED1000;
+		else if (phydev->speed == SPEED_100)
+			bmcr_ctl = BMCR_SPEED100;
+
+		if (phydev->duplex == DUPLEX_FULL)
+			bmcr_ctl |= BMCR_FULLDPLX;
+
+		err = phy_write(phydev, MII_BMCR, bmcr_ctl);
+		if (err < 0)
+			return err;
+
+		if (phydev->speed == SPEED_1000)
+			mscr2_ctl = BMCR_SPEED1000;
+		else if (phydev->speed == SPEED_100)
+			mscr2_ctl = BMCR_SPEED100;
+
+		err = phy_modify_paged(phydev, MII_MARVELL_MSCR_PAGE,
+				       MII_88E1510_MSCR_2, BMCR_SPEED1000 |
+				       BMCR_SPEED100, mscr2_ctl);
+		if (err < 0)
+			return err;
+
+		/* Need soft reset to have speed configuration takes effect */
+		err = genphy_soft_reset(phydev);
+		if (err < 0)
+			return err;
+
+		err = phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK,
+				 BMCR_LOOPBACK);
+
+		if (!err) {
+			/* It takes some time for PHY device to switch
+			 * into/out-of loopback mode.
+			 */
+			msleep(1000);
+		}
+		return err;
+	} else {
+		err = phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK, 0);
+		if (err < 0)
+			return err;
+
+		return phy_config_aneg(phydev);
+	}
+}
+
 static int marvell_vct5_wait_complete(struct phy_device *phydev)
 {
 	int i;
@@ -3078,7 +3141,7 @@
 		.get_sset_count = marvell_get_sset_count,
 		.get_strings = marvell_get_strings,
 		.get_stats = marvell_get_stats,
-		.set_loopback = genphy_loopback,
+		.set_loopback = m88e1510_loopback,
 		.get_tunable = m88e1011_get_tunable,
 		.set_tunable = m88e1011_set_tunable,
 		.cable_test_start = marvell_vct7_cable_test_start,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/marvell10g.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/marvell10g.c
@@ -307,6 +307,13 @@
 	ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
 				 MV_V2_PORT_CTRL_PWRDOWN);
 
+	/* Sometimes, the power down bit doesn't clear immediately, and
+	 * a read of this register causes the bit not to clear. Delay
+	 * 100us to allow the PHY to come out of power down mode before
+	 * the next access.
+	 */
+	udelay(100);
+
 	if (phydev->drv->phy_id != MARVELL_PHY_ID_88X3310 ||
 	    priv->firmware_ver < 0x00030000)
 		return ret;
@@ -789,7 +796,7 @@
 
 	cssr1 = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSSR1);
 	if (cssr1 < 0)
-		return val;
+		return cssr1;
 
 	/* If the link settings are not resolved, mark the link down */
 	if (!(cssr1 & MV_PCS_CSSR1_RESOLVED)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mdio_bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mdio_bus.c
@@ -108,7 +108,12 @@
 
 struct phy_device *mdiobus_get_phy(struct mii_bus *bus, int addr)
 {
-	struct mdio_device *mdiodev = bus->mdio_map[addr];
+	struct mdio_device *mdiodev;
+
+	if (addr < 0 || addr >= ARRAY_SIZE(bus->mdio_map))
+		return NULL;
+
+	mdiodev = bus->mdio_map[addr];
 
 	if (!mdiodev)
 		return NULL;
@@ -577,7 +582,7 @@
 	}
 
 	for (i = 0; i < PHY_MAX_ADDR; i++) {
-		if ((bus->phy_mask & (1 << i)) == 0) {
+		if ((bus->phy_mask & BIT(i)) == 0) {
 			struct phy_device *phydev;
 
 			phydev = mdiobus_scan(bus, i);
@@ -591,7 +596,7 @@
 	mdiobus_setup_mdiodev_from_board_info(bus, mdiobus_create_device);
 
 	bus->state = MDIOBUS_REGISTERED;
-	pr_info("%s: probed\n", bus->name);
+	dev_dbg(&bus->dev, "probed\n");
 	return 0;
 
 error:
@@ -1011,7 +1016,6 @@
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(mdio_bus_init);
 
 #if IS_ENABLED(CONFIG_PHYLIB)
 void mdio_bus_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mdio_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mdio_device.c
@@ -21,6 +21,7 @@
 #include <linux/slab.h>
 #include <linux/string.h>
 #include <linux/unistd.h>
+#include <linux/property.h>
 
 void mdio_device_free(struct mdio_device *mdiodev)
 {
@@ -30,6 +31,7 @@
 
 static void mdio_device_release(struct device *dev)
 {
+	fwnode_handle_put(dev->fwnode);
 	kfree(to_mdio_device(dev));
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mdio_devres.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mdio_devres.c
@@ -98,13 +98,14 @@
 
 #if IS_ENABLED(CONFIG_OF_MDIO)
 /**
- * devm_of_mdiobus_register - Resource managed variant of of_mdiobus_register()
+ * __devm_of_mdiobus_register - Resource managed variant of of_mdiobus_register()
  * @dev:	Device to register mii_bus for
  * @mdio:	MII bus structure to register
  * @np:		Device node to parse
+ * @owner:	Owning module
  */
-int devm_of_mdiobus_register(struct device *dev, struct mii_bus *mdio,
-			     struct device_node *np)
+int __devm_of_mdiobus_register(struct device *dev, struct mii_bus *mdio,
+			       struct device_node *np, struct module *owner)
 {
 	struct mdiobus_devres *dr;
 	int ret;
@@ -117,7 +118,7 @@
 	if (!dr)
 		return -ENOMEM;
 
-	ret = of_mdiobus_register(mdio, np);
+	ret = __of_mdiobus_register(mdio, np, owner);
 	if (ret) {
 		devres_free(dr);
 		return ret;
@@ -127,7 +128,7 @@
 	devres_add(dev, dr);
 	return 0;
 }
-EXPORT_SYMBOL(devm_of_mdiobus_register);
+EXPORT_SYMBOL(__devm_of_mdiobus_register);
 #endif /* CONFIG_OF_MDIO */
 
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mediatek-ge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mediatek-ge.c
@@ -55,9 +55,6 @@
 
 static int mt7531_phy_config_init(struct phy_device *phydev)
 {
-	if (phydev->interface != PHY_INTERFACE_MODE_INTERNAL)
-		return -EINVAL;
-
 	mtk_gephy_config_init(phydev);
 
 	/* PHY link down power saving enable */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/meson-gxl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/meson-gxl.c
@@ -30,8 +30,12 @@
 #define  INTSRC_LINK_DOWN	BIT(4)
 #define  INTSRC_REMOTE_FAULT	BIT(5)
 #define  INTSRC_ANEG_COMPLETE	BIT(6)
+#define  INTSRC_ENERGY_DETECT	BIT(7)
 #define INTSRC_MASK	30
 
+#define INT_SOURCES (INTSRC_LINK_DOWN | INTSRC_ANEG_COMPLETE | \
+		     INTSRC_ENERGY_DETECT)
+
 #define BANK_ANALOG_DSP		0
 #define BANK_WOL		1
 #define BANK_BIST		3
@@ -200,7 +204,6 @@
 
 static int meson_gxl_config_intr(struct phy_device *phydev)
 {
-	u16 val;
 	int ret;
 
 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
@@ -209,16 +212,9 @@
 		if (ret)
 			return ret;
 
-		val = INTSRC_ANEG_PR
-			| INTSRC_PARALLEL_FAULT
-			| INTSRC_ANEG_LP_ACK
-			| INTSRC_LINK_DOWN
-			| INTSRC_REMOTE_FAULT
-			| INTSRC_ANEG_COMPLETE;
-		ret = phy_write(phydev, INTSRC_MASK, val);
+		ret = phy_write(phydev, INTSRC_MASK, INT_SOURCES);
 	} else {
-		val = 0;
-		ret = phy_write(phydev, INTSRC_MASK, val);
+		ret = phy_write(phydev, INTSRC_MASK, 0);
 
 		/* Ack any pending IRQ */
 		ret = meson_gxl_ack_interrupt(phydev);
@@ -237,9 +233,16 @@
 		return IRQ_NONE;
 	}
 
+	irq_status &= INT_SOURCES;
+
 	if (irq_status == 0)
 		return IRQ_NONE;
 
+	/* Aneg-complete interrupt is used for link-up detection */
+	if (phydev->autoneg == AUTONEG_ENABLE &&
+	    irq_status == INTSRC_ENERGY_DETECT)
+		return IRQ_HANDLED;
+
 	phy_trigger_machine(phydev);
 
 	return IRQ_HANDLED;
@@ -258,6 +261,8 @@
 		.handle_interrupt = meson_gxl_handle_interrupt,
 		.suspend        = genphy_suspend,
 		.resume         = genphy_resume,
+		.read_mmd	= genphy_read_mmd_unsupported,
+		.write_mmd	= genphy_write_mmd_unsupported,
 	}, {
 		PHY_ID_MATCH_EXACT(0x01803301),
 		.name		= "Meson G12A Internal PHY",
@@ -268,6 +273,8 @@
 		.handle_interrupt = meson_gxl_handle_interrupt,
 		.suspend        = genphy_suspend,
 		.resume         = genphy_resume,
+		.read_mmd	= genphy_read_mmd_unsupported,
+		.write_mmd	= genphy_write_mmd_unsupported,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/micrel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/micrel.c
@@ -335,7 +335,7 @@
 		}
 	}
 
-	if (priv->led_mode >= 0)
+	if (priv->type && priv->led_mode >= 0)
 		kszphy_setup_led(phydev, priv->type->led_mode_reg, priv->led_mode);
 
 	return 0;
@@ -351,10 +351,10 @@
 
 	type = priv->type;
 
-	if (type->has_broadcast_disable)
+	if (type && type->has_broadcast_disable)
 		kszphy_broadcast_disable(phydev);
 
-	if (type->has_nand_tree_disable)
+	if (type && type->has_nand_tree_disable)
 		kszphy_nand_tree_disable(phydev);
 
 	return kszphy_config_reset(phydev);
@@ -863,9 +863,9 @@
 				MII_KSZ9031RN_TX_DATA_PAD_SKEW, 4,
 				tx_data_skews, 4, &update);
 
-		if (update && phydev->interface != PHY_INTERFACE_MODE_RGMII)
+		if (update && !phy_interface_is_rgmii(phydev))
 			phydev_warn(phydev,
-				    "*-skew-ps values should be used only with phy-mode = \"rgmii\"\n");
+				    "*-skew-ps values should be used only with RGMII PHY modes\n");
 
 		/* Silicon Errata Sheet (DS80000691D or DS80000692D):
 		 * When the device links in the 1000BASE-T slave mode only,
@@ -1328,7 +1328,7 @@
 
 	priv->type = type;
 
-	if (type->led_mode_reg) {
+	if (type && type->led_mode_reg) {
 		ret = of_property_read_u32(np, "micrel,led-mode",
 				&priv->led_mode);
 		if (ret)
@@ -1349,7 +1349,8 @@
 		unsigned long rate = clk_get_rate(clk);
 		bool rmii_ref_clk_sel_25_mhz;
 
-		priv->rmii_ref_clk_sel = type->has_rmii_ref_clk_sel;
+		if (type)
+			priv->rmii_ref_clk_sel = type->has_rmii_ref_clk_sel;
 		rmii_ref_clk_sel_25_mhz = of_property_read_bool(np,
 				"micrel,rmii-reference-clock-select-25-mhz");
 
@@ -1544,11 +1545,12 @@
 	.name		= "Micrel KS8737",
 	/* PHY_BASIC_FEATURES */
 	.driver_data	= &ks8737_type,
+	.probe		= kszphy_probe,
 	.config_init	= kszphy_config_init,
 	.config_intr	= kszphy_config_intr,
 	.handle_interrupt = kszphy_handle_interrupt,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_KSZ8021,
 	.phy_id_mask	= 0x00ffffff,
@@ -1562,8 +1564,8 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_KSZ8031,
 	.phy_id_mask	= 0x00ffffff,
@@ -1577,8 +1579,8 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_KSZ8041,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
@@ -1593,8 +1595,9 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	/* No suspend/resume callbacks because of errata DS80000700A,
+	 * receiver error following software power down.
+	 */
 }, {
 	.phy_id		= PHY_ID_KSZ8041RNLI,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
@@ -1608,8 +1611,8 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 }, {
 	.name		= "Micrel KSZ8051",
 	/* PHY_BASIC_FEATURES */
@@ -1622,8 +1625,8 @@
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
 	.match_phy_device = ksz8051_match_phy_device,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_KSZ8001,
 	.name		= "Micrel KSZ8001 or KS8721",
@@ -1637,8 +1640,8 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_KSZ8081,
 	.name		= "Micrel KSZ8081 or KSZ8091",
@@ -1666,6 +1669,7 @@
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	/* PHY_BASIC_FEATURES */
 	.config_init	= ksz8061_config_init,
+	.soft_reset	= genphy_soft_reset,
 	.config_intr	= kszphy_config_intr,
 	.handle_interrupt = kszphy_handle_interrupt,
 	.suspend	= genphy_suspend,
@@ -1684,8 +1688,8 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
-	.resume		= genphy_resume,
+	.suspend	= kszphy_suspend,
+	.resume		= kszphy_resume,
 	.read_mmd	= genphy_read_mmd_unsupported,
 	.write_mmd	= genphy_write_mmd_unsupported,
 }, {
@@ -1703,7 +1707,7 @@
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
+	.suspend	= kszphy_suspend,
 	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_LAN8814,
@@ -1725,13 +1729,14 @@
 	/* PHY_GBIT_FEATURES */
 	.driver_data	= &ksz9021_type,
 	.probe		= kszphy_probe,
+	.soft_reset	= genphy_soft_reset,
 	.config_init	= ksz9131_config_init,
 	.config_intr	= kszphy_config_intr,
 	.handle_interrupt = kszphy_handle_interrupt,
 	.get_sset_count = kszphy_get_sset_count,
 	.get_strings	= kszphy_get_strings,
 	.get_stats	= kszphy_get_stats,
-	.suspend	= genphy_suspend,
+	.suspend	= kszphy_suspend,
 	.resume		= kszphy_resume,
 }, {
 	.phy_id		= PHY_ID_KSZ8873MLL,
@@ -1793,6 +1798,7 @@
 	{ PHY_ID_KSZ8081, MICREL_PHY_ID_MASK },
 	{ PHY_ID_KSZ8873MLL, MICREL_PHY_ID_MASK },
 	{ PHY_ID_KSZ886X, MICREL_PHY_ID_MASK },
+	{ PHY_ID_KSZ9477, MICREL_PHY_ID_MASK },
 	{ PHY_ID_LAN8814, MICREL_PHY_ID_MASK },
 	{ }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/microchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/microchip.c
@@ -342,6 +342,37 @@
 	return genphy_config_aneg(phydev);
 }
 
+static void lan88xx_link_change_notify(struct phy_device *phydev)
+{
+	int temp;
+
+	/* At forced 100 F/H mode, chip may fail to set mode correctly
+	 * when cable is switched between long(~50+m) and short one.
+	 * As workaround, set to 10 before setting to 100
+	 * at forced 100 F/H mode.
+	 */
+	if (!phydev->autoneg && phydev->speed == 100) {
+		/* disable phy interrupt */
+		temp = phy_read(phydev, LAN88XX_INT_MASK);
+		temp &= ~LAN88XX_INT_MASK_MDINTPIN_EN_;
+		phy_write(phydev, LAN88XX_INT_MASK, temp);
+
+		temp = phy_read(phydev, MII_BMCR);
+		temp &= ~(BMCR_SPEED100 | BMCR_SPEED1000);
+		phy_write(phydev, MII_BMCR, temp); /* set to 10 first */
+		temp |= BMCR_SPEED100;
+		phy_write(phydev, MII_BMCR, temp); /* set to 100 later */
+
+		/* clear pending interrupt generated while workaround */
+		temp = phy_read(phydev, LAN88XX_INT_STS);
+
+		/* enable phy interrupt back */
+		temp = phy_read(phydev, LAN88XX_INT_MASK);
+		temp |= LAN88XX_INT_MASK_MDINTPIN_EN_;
+		phy_write(phydev, LAN88XX_INT_MASK, temp);
+	}
+}
+
 static struct phy_driver microchip_phy_driver[] = {
 {
 	.phy_id		= 0x0007c130,
@@ -355,6 +386,7 @@
 
 	.config_init	= lan88xx_config_init,
 	.config_aneg	= lan88xx_config_aneg,
+	.link_change_notify = lan88xx_link_change_notify,
 
 	.config_intr	= lan88xx_phy_config_intr,
 	.handle_interrupt = lan88xx_handle_interrupt,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mscc/mscc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mscc/mscc.h
@@ -178,7 +178,9 @@
 /* RGMII controls at address 20E2, for VSC8502 and similar */
 #define VSC8502_RGMII_CNTL		  20
 #define VSC8502_RGMII_RX_DELAY_MASK	  0x0070
+#define VSC8502_RGMII_RX_CLK_DELAY_POS	  4
 #define VSC8502_RGMII_TX_DELAY_MASK	  0x0007
+#define VSC8502_RGMII_RX_CLK_DISABLE	  0x0800
 
 #define MSCC_PHY_WOL_LOWER_MAC_ADDR	  21
 #define MSCC_PHY_WOL_MID_MAC_ADDR	  22
@@ -281,6 +283,7 @@
 #define PHY_ID_VSC8514			  0x00070670
 #define PHY_ID_VSC8530			  0x00070560
 #define PHY_ID_VSC8531			  0x00070570
+#define PHY_ID_VSC8531_02		  0x00070572
 #define PHY_ID_VSC8540			  0x00070760
 #define PHY_ID_VSC8541			  0x00070770
 #define PHY_ID_VSC8552			  0x000704e0
@@ -373,6 +376,8 @@
 	 * package.
 	 */
 	unsigned int base_addr;
+	u32 rx_delay;
+	u32 tx_delay;
 
 #if IS_ENABLED(CONFIG_MACSEC)
 	/* MACsec fields:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mscc/mscc_macsec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mscc/mscc_macsec.c
@@ -632,6 +632,7 @@
 
 	list_del(&flow->list);
 	clear_bit(flow->index, bitmap);
+	memzero_explicit(flow->key, sizeof(flow->key));
 	kfree(flow);
 }
 
@@ -879,6 +880,9 @@
 {
 	struct macsec_flow *flow;
 
+	if (ctx->sa.update_pn)
+		return -EINVAL;
+
 	flow = vsc8584_macsec_find_flow(ctx, MACSEC_INGR);
 	if (IS_ERR(flow))
 		return PTR_ERR(flow);
@@ -928,6 +932,9 @@
 {
 	struct macsec_flow *flow;
 
+	if (ctx->sa.update_pn)
+		return -EINVAL;
+
 	flow = vsc8584_macsec_find_flow(ctx, MACSEC_EGR);
 	if (IS_ERR(flow))
 		return PTR_ERR(flow);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mscc/mscc_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mscc/mscc_main.c
@@ -273,12 +273,12 @@
 static int vsc85xx_wol_set(struct phy_device *phydev,
 			   struct ethtool_wolinfo *wol)
 {
+	const u8 *mac_addr = phydev->attached_dev->dev_addr;
 	int rc;
 	u16 reg_val;
 	u8  i;
 	u16 pwd[3] = {0, 0, 0};
 	struct ethtool_wolinfo *wol_conf = wol;
-	u8 *mac_addr = phydev->attached_dev->dev_addr;
 
 	mutex_lock(&phydev->lock);
 	rc = phy_select_page(phydev, MSCC_PHY_PAGE_EXTENDED_2);
@@ -527,17 +527,34 @@
  *  * 2.0 ns (which causes the data to be sampled at exactly half way between
  *    clock transitions at 1000 Mbps) if delays should be enabled
  */
-static int vsc85xx_rgmii_set_skews(struct phy_device *phydev, u32 rgmii_cntl,
-				   u16 rgmii_rx_delay_mask,
-				   u16 rgmii_tx_delay_mask)
+static int vsc85xx_update_rgmii_cntl(struct phy_device *phydev, u32 rgmii_cntl,
+				     u16 rgmii_rx_delay_mask,
+				     u16 rgmii_tx_delay_mask)
 {
 	u16 rgmii_rx_delay_pos = ffs(rgmii_rx_delay_mask) - 1;
 	u16 rgmii_tx_delay_pos = ffs(rgmii_tx_delay_mask) - 1;
 	u16 reg_val = 0;
-	int rc;
+	u16 mask = 0;
+	int rc = 0;
+	struct vsc8531_private *vsc8531 = phydev->priv;
+
+	/* For traffic to pass, the VSC8502 family needs the RX_CLK disable bit
+	 * to be unset for all PHY modes, so do that as part of the paged
+	 * register modification.
+	 * For some family members (like VSC8530/31/40/41) this bit is reserved
+	 * and read-only, and the RX clock is enabled by default.
+	 */
+	if (rgmii_cntl == VSC8502_RGMII_CNTL)
+		mask |= VSC8502_RGMII_RX_CLK_DISABLE;
+
+	if (phy_interface_is_rgmii(phydev))
+		mask |= rgmii_rx_delay_mask | rgmii_tx_delay_mask;
 
 	mutex_lock(&phydev->lock);
 
+	reg_val = (vsc8531->rx_delay << VSC8502_RGMII_RX_CLK_DELAY_POS) |
+		  vsc8531->tx_delay;
+
 	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
 	    phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
 		reg_val |= RGMII_CLK_DELAY_2_0_NS << rgmii_rx_delay_pos;
@@ -545,10 +562,9 @@
 	    phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
 		reg_val |= RGMII_CLK_DELAY_2_0_NS << rgmii_tx_delay_pos;
 
-	rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED_2,
-			      rgmii_cntl,
-			      rgmii_rx_delay_mask | rgmii_tx_delay_mask,
-			      reg_val);
+	if (mask)
+		rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED_2,
+				      rgmii_cntl, mask, reg_val);
 
 	mutex_unlock(&phydev->lock);
 
@@ -557,19 +573,11 @@
 
 static int vsc85xx_default_config(struct phy_device *phydev)
 {
-	int rc;
-
 	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
 
-	if (phy_interface_mode_is_rgmii(phydev->interface)) {
-		rc = vsc85xx_rgmii_set_skews(phydev, VSC8502_RGMII_CNTL,
-					     VSC8502_RGMII_RX_DELAY_MASK,
-					     VSC8502_RGMII_TX_DELAY_MASK);
-		if (rc)
-			return rc;
-	}
-
-	return 0;
+	return vsc85xx_update_rgmii_cntl(phydev, VSC8502_RGMII_CNTL,
+					 VSC8502_RGMII_RX_DELAY_MASK,
+					 VSC8502_RGMII_TX_DELAY_MASK);
 }
 
 static int vsc85xx_get_tunable(struct phy_device *phydev,
@@ -1766,13 +1774,11 @@
 	if (ret)
 		return ret;
 
-	if (phy_interface_is_rgmii(phydev)) {
-		ret = vsc85xx_rgmii_set_skews(phydev, VSC8572_RGMII_CNTL,
-					      VSC8572_RGMII_RX_DELAY_MASK,
-					      VSC8572_RGMII_TX_DELAY_MASK);
-		if (ret)
-			return ret;
-	}
+	ret = vsc85xx_update_rgmii_cntl(phydev, VSC8572_RGMII_CNTL,
+					VSC8572_RGMII_RX_DELAY_MASK,
+					VSC8572_RGMII_TX_DELAY_MASK);
+	if (ret)
+		return ret;
 
 	ret = genphy_soft_reset(phydev);
 	if (ret)
@@ -1820,6 +1826,17 @@
 {
 	int rc, i, phy_id;
 	struct vsc8531_private *vsc8531 = phydev->priv;
+	struct device_node *of_node = phydev->mdio.dev.of_node;
+
+	rc = of_property_read_u32(of_node, "vsc8531,rx-delay",
+				  &vsc8531->rx_delay);
+	if (rc < 0)
+		vsc8531->rx_delay = VSC8531_RGMII_CLK_DELAY_1_1_NS;
+
+	rc = of_property_read_u32(of_node, "vsc8531,tx-delay",
+				  &vsc8531->tx_delay);
+	if (rc < 0)
+		vsc8531->tx_delay = VSC8531_RGMII_CLK_DELAY_0_2_NS;
 
 	rc = vsc85xx_default_config(phydev);
 	if (rc)
@@ -2445,6 +2462,30 @@
 	.get_stats      = &vsc85xx_get_stats,
 },
 {
+	.phy_id		= PHY_ID_VSC8531_02,
+	.name		= "Microsemi VSC8531-02",
+	.phy_id_mask	= 0xfffffff0,
+	/* PHY_GBIT_FEATURES */
+	.soft_reset	= &genphy_soft_reset,
+	.config_init	= &vsc85xx_config_init,
+	.config_aneg	= &vsc85xx_config_aneg,
+	.aneg_done	= &genphy_aneg_done,
+	.read_status	= &vsc85xx_read_status,
+	.config_intr	= &vsc85xx_config_intr,
+	.suspend	= &genphy_suspend,
+	.resume		= &genphy_resume,
+	.probe		= &vsc85xx_probe,
+	.set_wol	= &vsc85xx_wol_set,
+	.get_wol	= &vsc85xx_wol_get,
+	.get_tunable	= &vsc85xx_get_tunable,
+	.set_tunable	= &vsc85xx_set_tunable,
+	.read_page	= &vsc85xx_phy_read_page,
+	.write_page	= &vsc85xx_phy_write_page,
+	.get_sset_count = &vsc85xx_get_sset_count,
+	.get_strings	= &vsc85xx_get_strings,
+	.get_stats	= &vsc85xx_get_stats,
+},
+{
 	.phy_id		= PHY_ID_VSC8540,
 	.name		= "Microsemi FE VSC8540 SyncE",
 	.phy_id_mask	= 0xfffffff0,
@@ -2664,10 +2705,12 @@
 module_phy_driver(vsc85xx_driver);
 
 static struct mdio_device_id __maybe_unused vsc85xx_tbl[] = {
+	{ PHY_ID_VSC8502, 0xfffffff0, },
 	{ PHY_ID_VSC8504, 0xfffffff0, },
 	{ PHY_ID_VSC8514, 0xfffffff0, },
 	{ PHY_ID_VSC8530, 0xfffffff0, },
 	{ PHY_ID_VSC8531, 0xfffffff0, },
+	{ PHY_ID_VSC8531_02, 0xfffffff0, },
 	{ PHY_ID_VSC8540, 0xfffffff0, },
 	{ PHY_ID_VSC8541, 0xfffffff0, },
 	{ PHY_ID_VSC8552, 0xfffffff0, },
@@ -2685,3 +2728,6 @@
 MODULE_DESCRIPTION("Microsemi VSC85xx PHY driver");
 MODULE_AUTHOR("Nagaraju Lakkaraju");
 MODULE_LICENSE("Dual MIT/GPL");
+
+MODULE_FIRMWARE(MSCC_VSC8584_REVB_INT8051_FW);
+MODULE_FIRMWARE(MSCC_VSC8574_REVB_INT8051_FW);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/mxl-gpy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/mxl-gpy.c
@@ -96,6 +96,7 @@
 
 static int gpy_probe(struct phy_device *phydev)
 {
+	int fw_version;
 	int ret;
 
 	if (!phydev->is_c45) {
@@ -105,12 +106,12 @@
 	}
 
 	/* Show GPY PHY FW version in dmesg */
-	ret = phy_read(phydev, PHY_FWV);
-	if (ret < 0)
-		return ret;
+	fw_version = phy_read(phydev, PHY_FWV);
+	if (fw_version < 0)
+		return fw_version;
 
-	phydev_info(phydev, "Firmware Version: 0x%04X (%s)\n", ret,
-		    (ret & PHY_FWV_REL_MASK) ? "release" : "test");
+	phydev_info(phydev, "Firmware Version: 0x%04X (%s)\n", fw_version,
+		    (fw_version & PHY_FWV_REL_MASK) ? "release" : "test");
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/nxp-c45-tja11xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/nxp-c45-tja11xx.c
@@ -79,7 +79,7 @@
 #define SGMII_ABILITY			BIT(0)
 
 #define VEND1_MII_BASIC_CONFIG		0xAFC6
-#define MII_BASIC_CONFIG_REV		BIT(8)
+#define MII_BASIC_CONFIG_REV		BIT(4)
 #define MII_BASIC_CONFIG_SGMII		0x9
 #define MII_BASIC_CONFIG_RGMII		0x7
 #define MII_BASIC_CONFIG_RMII		0x5
@@ -168,7 +168,7 @@
 #define MAX_ID_PS			2260U
 #define DEFAULT_ID_PS			2000U
 
-#define PPM_TO_SUBNS_INC(ppb)	div_u64(GENMASK(31, 0) * (ppb) * \
+#define PPM_TO_SUBNS_INC(ppb)	div_u64(GENMASK_ULL(31, 0) * (ppb) * \
 					PTP_CLK_PERIOD_100BT1, NSEC_PER_SEC)
 
 #define NXP_C45_SKB_CB(skb)	((struct nxp_c45_skb_cb *)(skb)->cb)
@@ -717,6 +717,8 @@
 	if (ret)
 		return ret;
 
+	usleep_range(2000, 2050);
+
 	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1,
 					 VEND1_DEVICE_CONTROL, ret,
 					 !(ret & DEVICE_CONTROL_RESET), 20000,
@@ -1117,6 +1119,17 @@
 	return ret;
 }
 
+static void nxp_c45_remove(struct phy_device *phydev)
+{
+	struct nxp_c45_phy *priv = phydev->priv;
+
+	if (priv->ptp_clock)
+		ptp_clock_unregister(priv->ptp_clock);
+
+	skb_queue_purge(&priv->tx_queue);
+	skb_queue_purge(&priv->rx_queue);
+}
+
 static struct phy_driver nxp_c45_driver[] = {
 	{
 		PHY_ID_MATCH_MODEL(PHY_ID_TJA_1103),
@@ -1139,6 +1152,7 @@
 		.set_loopback		= genphy_c45_loopback,
 		.get_sqi		= nxp_c45_get_sqi,
 		.get_sqi_max		= nxp_c45_get_sqi_max,
+		.remove			= nxp_c45_remove,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/phy-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/phy-core.c
@@ -162,11 +162,11 @@
 	PHY_SETTING(   2500, FULL,   2500baseT_Full		),
 	PHY_SETTING(   2500, FULL,   2500baseX_Full		),
 	/* 1G */
-	PHY_SETTING(   1000, FULL,   1000baseKX_Full		),
 	PHY_SETTING(   1000, FULL,   1000baseT_Full		),
 	PHY_SETTING(   1000, HALF,   1000baseT_Half		),
 	PHY_SETTING(   1000, FULL,   1000baseT1_Full		),
 	PHY_SETTING(   1000, FULL,   1000baseX_Full		),
+	PHY_SETTING(   1000, FULL,   1000baseKX_Full		),
 	/* 100M */
 	PHY_SETTING(    100, FULL,    100baseT_Full		),
 	PHY_SETTING(    100, FULL,    100baseT1_Full		),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/phy.c
@@ -31,6 +31,7 @@
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/atomic.h>
+#include <linux/suspend.h>
 #include <net/netlink.h>
 #include <net/genetlink.h>
 #include <net/sock.h>
@@ -56,6 +57,18 @@
 	return NULL;
 }
 
+static void phy_process_state_change(struct phy_device *phydev,
+				     enum phy_state old_state)
+{
+	if (old_state != phydev->state) {
+		phydev_dbg(phydev, "PHY state change %s -> %s\n",
+			   phy_state_to_str(old_state),
+			   phy_state_to_str(phydev->state));
+		if (phydev->drv && phydev->drv->link_change_notify)
+			phydev->drv->link_change_notify(phydev);
+	}
+}
+
 static void phy_link_up(struct phy_device *phydev)
 {
 	phydev->phy_link_change(phydev, true);
@@ -815,7 +828,12 @@
 	phydev->mdix_ctrl = cmd->base.eth_tp_mdix_ctrl;
 
 	/* Restart the PHY */
-	_phy_start_aneg(phydev);
+	if (phy_is_started(phydev)) {
+		phydev->state = PHY_UP;
+		phy_trigger_machine(phydev);
+	} else {
+		_phy_start_aneg(phydev);
+	}
 
 	mutex_unlock(&phydev->lock);
 	return 0;
@@ -965,8 +983,35 @@
 {
 	struct phy_device *phydev = phy_dat;
 	struct phy_driver *drv = phydev->drv;
+	irqreturn_t ret;
 
-	return drv->handle_interrupt(phydev);
+	/* Wakeup interrupts may occur during a system sleep transition.
+	 * Postpone handling until the PHY has resumed.
+	 */
+	if (IS_ENABLED(CONFIG_PM_SLEEP) && phydev->irq_suspended) {
+		struct net_device *netdev = phydev->attached_dev;
+
+		if (netdev) {
+			struct device *parent = netdev->dev.parent;
+
+			if (netdev->wol_enabled)
+				pm_system_wakeup();
+			else if (device_may_wakeup(&netdev->dev))
+				pm_wakeup_dev_event(&netdev->dev, 0, true);
+			else if (parent && device_may_wakeup(parent))
+				pm_wakeup_dev_event(parent, 0, true);
+		}
+
+		phydev->irq_rerun = 1;
+		disable_irq_nosync(irq);
+		return IRQ_HANDLED;
+	}
+
+	mutex_lock(&phydev->lock);
+	ret = drv->handle_interrupt(phydev);
+	mutex_unlock(&phydev->lock);
+
+	return ret;
 }
 
 /**
@@ -1028,6 +1073,7 @@
 void phy_stop(struct phy_device *phydev)
 {
 	struct net_device *dev = phydev->attached_dev;
+	enum phy_state old_state;
 
 	if (!phy_is_started(phydev) && phydev->state != PHY_DOWN) {
 		WARN(1, "called from state %s\n",
@@ -1036,6 +1082,7 @@
 	}
 
 	mutex_lock(&phydev->lock);
+	old_state = phydev->state;
 
 	if (phydev->state == PHY_CABLETEST) {
 		phy_abort_cable_test(phydev);
@@ -1046,12 +1093,10 @@
 		sfp_upstream_stop(phydev->sfp_bus);
 
 	phydev->state = PHY_HALTED;
+	phy_process_state_change(phydev, old_state);
 
 	mutex_unlock(&phydev->lock);
 
-	phy_state_machine(&phydev->state_queue.work);
-	phy_stop_machine(phydev);
-
 	/* Cannot call flush_scheduled_work() here as desired because
 	 * of rtnl_lock(), but PHY_HALTED shall guarantee irq handler
 	 * will not reenable interrupts.
@@ -1163,13 +1208,7 @@
 	if (err < 0)
 		phy_error(phydev);
 
-	if (old_state != phydev->state) {
-		phydev_dbg(phydev, "PHY state change %s -> %s\n",
-			   phy_state_to_str(old_state),
-			   phy_state_to_str(phydev->state));
-		if (phydev->drv && phydev->drv->link_change_notify)
-			phydev->drv->link_change_notify(phydev);
-	}
+	phy_process_state_change(phydev, old_state);
 
 	/* Only re-schedule a PHY state machine change if we are polling the
 	 * PHY, if PHY_MAC_INTERRUPT is set, then we will be moving
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/phy_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/phy_device.c
@@ -215,6 +215,7 @@
 
 static void phy_device_release(struct device *dev)
 {
+	fwnode_handle_put(dev->fwnode);
 	kfree(to_phy_device(dev));
 }
 
@@ -277,6 +278,15 @@
 	if (phydev->mac_managed_pm)
 		return 0;
 
+	/* Wakeup interrupts may occur during the system sleep transition when
+	 * the PHY is inaccessible. Set flag to postpone handling until the PHY
+	 * has resumed. Wait for concurrent interrupt handler to complete.
+	 */
+	if (phy_interrupt_is_valid(phydev)) {
+		phydev->irq_suspended = 1;
+		synchronize_irq(phydev->irq);
+	}
+
 	/* We must stop the state machine manually, otherwise it stops out of
 	 * control, possibly with the phydev->lock held. Upon resume, netdev
 	 * may call phy routines that try to grab the same lock, and that may
@@ -306,6 +316,14 @@
 
 	phydev->suspended_by_mdio_bus = 0;
 
+	/* If we managed to get here with the PHY state machine in a state
+	 * neither PHY_HALTED, PHY_READY nor PHY_UP, this is an indication
+	 * that something went wrong and we should most likely be using
+	 * MAC managed PM, but we are not.
+	 */
+	WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
+		phydev->state != PHY_UP);
+
 	ret = phy_init_hw(phydev);
 	if (ret < 0)
 		return ret;
@@ -314,6 +332,20 @@
 	if (ret < 0)
 		return ret;
 no_resume:
+	if (phy_interrupt_is_valid(phydev)) {
+		phydev->irq_suspended = 0;
+		synchronize_irq(phydev->irq);
+
+		/* Rerun interrupts which were postponed by phy_interrupt()
+		 * because they occurred during the system sleep transition.
+		 */
+		if (phydev->irq_rerun) {
+			phydev->irq_rerun = 0;
+			enable_irq(phydev->irq);
+			irq_wake_thread(phydev->irq, phydev);
+		}
+	}
+
 	if (phydev->attached_dev && phydev->adjust_link)
 		phy_start_machine(phydev);
 
@@ -1114,6 +1146,8 @@
 	if (phy_interrupt_is_valid(phydev))
 		phy_free_interrupt(phydev);
 
+	phy_stop_machine(phydev);
+
 	phydev->adjust_link = NULL;
 
 	phy_detach(phydev);
@@ -1487,6 +1521,7 @@
 
 error_module_put:
 	module_put(d->driver->owner);
+	d->driver = NULL;
 error_put_device:
 	put_device(d);
 	if (ndev_owner != bus->owner)
@@ -1746,6 +1781,9 @@
 	    phy_driver_is_genphy_10g(phydev))
 		device_release_driver(&phydev->mdio.dev);
 
+	/* Assert the reset signal */
+	phy_device_reset(phydev, 1);
+
 	/*
 	 * The phydev might go away on the put_device() below, so avoid
 	 * a use-after-free bug by reading the underlying bus first.
@@ -1757,9 +1795,6 @@
 		ndev_owner = dev->dev.parent->driver->owner;
 	if (ndev_owner != bus->owner)
 		module_put(bus->owner);
-
-	/* Assert the reset signal */
-	phy_device_reset(phydev, 1);
 }
 EXPORT_SYMBOL(phy_detach);
 
@@ -2612,8 +2647,8 @@
 int genphy_loopback(struct phy_device *phydev, bool enable)
 {
 	if (enable) {
-		u16 val, ctl = BMCR_LOOPBACK;
-		int ret;
+		u16 ctl = BMCR_LOOPBACK;
+		int ret, val;
 
 		if (phydev->speed == SPEED_1000)
 			ctl |= BMCR_SPEED1000;
@@ -2871,7 +2906,7 @@
 	if (delay < 0)
 		return delay;
 
-	if (delay && size == 0)
+	if (size == 0)
 		return delay;
 
 	if (delay < delay_values[0] || delay > delay_values[size - 1]) {
@@ -3019,8 +3054,6 @@
 	if (phydrv->flags & PHY_IS_INTERNAL)
 		phydev->is_internal = true;
 
-	mutex_lock(&phydev->lock);
-
 	/* Deassert the reset signal */
 	phy_device_reset(phydev, 0);
 
@@ -3030,6 +3063,8 @@
 			goto out;
 	}
 
+	phy_disable_interrupts(phydev);
+
 	/* Start out supporting everything. Eventually,
 	 * a controller will attach, and may modify one
 	 * or both of these values
@@ -3088,12 +3123,10 @@
 	phydev->state = PHY_READY;
 
 out:
-	/* Assert the reset signal */
+	/* Re-assert the reset signal on error */
 	if (err)
 		phy_device_reset(phydev, 1);
 
-	mutex_unlock(&phydev->lock);
-
 	return err;
 }
 
@@ -3103,9 +3136,7 @@
 
 	cancel_delayed_work_sync(&phydev->state_queue);
 
-	mutex_lock(&phydev->lock);
 	phydev->state = PHY_DOWN;
-	mutex_unlock(&phydev->lock);
 
 	sfp_bus_del_upstream(phydev->sfp_bus);
 	phydev->sfp_bus = NULL;
@@ -3121,16 +3152,6 @@
 	return 0;
 }
 
-static void phy_shutdown(struct device *dev)
-{
-	struct phy_device *phydev = to_phy_device(dev);
-
-	if (phydev->state == PHY_READY || !phydev->attached_dev)
-		return;
-
-	phy_disable_interrupts(phydev);
-}
-
 /**
  * phy_driver_register - register a phy_driver with the PHY layer
  * @new_driver: new phy_driver to register
@@ -3154,7 +3175,6 @@
 	new_driver->mdiodrv.driver.bus = &mdio_bus_type;
 	new_driver->mdiodrv.driver.probe = phy_probe;
 	new_driver->mdiodrv.driver.remove = phy_remove;
-	new_driver->mdiodrv.driver.shutdown = phy_shutdown;
 	new_driver->mdiodrv.driver.owner = owner;
 	new_driver->mdiodrv.driver.probe_type = PROBE_FORCE_SYNCHRONOUS;
 
@@ -3226,23 +3246,30 @@
 {
 	int rc;
 
+	ethtool_set_ethtool_phy_ops(&phy_ethtool_phy_ops);
+
 	rc = mdio_bus_init();
 	if (rc)
-		return rc;
+		goto err_ethtool_phy_ops;
 
-	ethtool_set_ethtool_phy_ops(&phy_ethtool_phy_ops);
 	features_init();
 
 	rc = phy_driver_register(&genphy_c45_driver, THIS_MODULE);
 	if (rc)
-		goto err_c45;
+		goto err_mdio_bus;
 
 	rc = phy_driver_register(&genphy_driver, THIS_MODULE);
-	if (rc) {
-		phy_driver_unregister(&genphy_c45_driver);
+	if (rc)
+		goto err_c45;
+
+	return 0;
+
 err_c45:
-		mdio_bus_exit();
-	}
+	phy_driver_unregister(&genphy_c45_driver);
+err_mdio_bus:
+	mdio_bus_exit();
+err_ethtool_phy_ops:
+	ethtool_set_ethtool_phy_ops(NULL);
 
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/phylink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/phylink.c
@@ -657,6 +657,7 @@
 	struct phylink_link_state link_state;
 	struct net_device *ndev = pl->netdev;
 	bool mac_config = false;
+	bool retrigger = false;
 	bool cur_link_state;
 
 	mutex_lock(&pl->state_mutex);
@@ -670,6 +671,7 @@
 		link_state.link = false;
 	} else if (pl->mac_link_dropped) {
 		link_state.link = false;
+		retrigger = true;
 	} else {
 		switch (pl->cur_link_an_mode) {
 		case MLO_AN_PHY:
@@ -686,6 +688,19 @@
 		case MLO_AN_INBAND:
 			phylink_mac_pcs_get_state(pl, &link_state);
 
+			/* The PCS may have a latching link-fail indicator.
+			 * If the link was up, bring the link down and
+			 * re-trigger the resolve. Otherwise, re-read the
+			 * PCS state to get the current status of the link.
+			 */
+			if (!link_state.link) {
+				if (cur_link_state)
+					retrigger = true;
+				else
+					phylink_mac_pcs_get_state(pl,
+								  &link_state);
+			}
+
 			/* If we have a phy, the "up" state is the union of
 			 * both the PHY and the MAC
 			 */
@@ -694,6 +709,15 @@
 
 			/* Only update if the PHY link is up */
 			if (pl->phydev && pl->phy_state.link) {
+				/* If the interface has changed, force a
+				 * link down event if the link isn't already
+				 * down, and re-resolve.
+				 */
+				if (link_state.interface !=
+				    pl->phy_state.interface) {
+					retrigger = true;
+					link_state.link = false;
+				}
 				link_state.interface = pl->phy_state.interface;
 
 				/* If we have a PHY, we need to update with
@@ -736,7 +760,7 @@
 		else
 			phylink_link_up(pl, link_state);
 	}
-	if (!link_state.link && pl->mac_link_dropped) {
+	if (!link_state.link && retrigger) {
 		pl->mac_link_dropped = false;
 		queue_work(system_power_efficient_wq, &pl->resolve);
 	}
@@ -829,6 +853,7 @@
 	pl->config = config;
 	if (config->type == PHYLINK_NETDEV) {
 		pl->netdev = to_net_dev(config->dev);
+		netif_carrier_off(pl->netdev);
 	} else if (config->type == PHYLINK_DEV) {
 		pl->dev = config->dev;
 	} else {
@@ -1026,6 +1051,9 @@
 	if (phy_interrupt_is_valid(phy))
 		phy_request_interrupt(phy);
 
+	if (pl->config->mac_managed_pm)
+		phy->mac_managed_pm = true;
+
 	return 0;
 }
 
@@ -1139,10 +1167,9 @@
 
 	ret = phy_attach_direct(pl->netdev, phy_dev, flags,
 				pl->link_interface);
-	if (ret) {
-		phy_device_free(phy_dev);
+	phy_device_free(phy_dev);
+	if (ret)
 		return ret;
-	}
 
 	ret = phylink_bringup_phy(pl, phy_dev, pl->link_config.interface);
 	if (ret)
@@ -1333,7 +1360,10 @@
 		 * but one would hope all packets have been sent. This
 		 * also means phylink_resolve() will do nothing.
 		 */
-		netif_carrier_off(pl->netdev);
+		if (pl->netdev)
+			netif_carrier_off(pl->netdev);
+		else
+			pl->old_link_state = false;
 
 		/* We do not call mac_link_down() here as we want the
 		 * link to remain up to receive the WoL packets.
@@ -1724,7 +1754,7 @@
 		return -EOPNOTSUPP;
 
 	if (!phylink_test(pl->supported, Asym_Pause) &&
-	    !pause->autoneg && pause->rx_pause != pause->tx_pause)
+	    pause->rx_pause != pause->tx_pause)
 		return -EINVAL;
 
 	pause_state = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/sfp-bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/sfp-bus.c
@@ -75,6 +75,12 @@
 		.part = "MA5671A",
 		.modes = sfp_quirk_2500basex,
 	}, {
+		// Lantech 8330-262D-E can operate at 2500base-X, but
+		// incorrectly report 2500MBd NRZ in their EEPROM
+		.vendor = "Lantech",
+		.part = "8330-262D-E",
+		.modes = sfp_quirk_2500basex,
+	}, {
 		.vendor = "UBNT",
 		.part = "UF-INSTANT",
 		.modes = sfp_quirk_ubnt_uf_instant,
@@ -651,6 +657,11 @@
 	else if (ret < 0)
 		return ERR_PTR(ret);
 
+	if (!fwnode_device_is_available(ref.fwnode)) {
+		fwnode_handle_put(ref.fwnode);
+		return NULL;
+	}
+
 	bus = sfp_bus_get(ref.fwnode);
 	fwnode_handle_put(ref.fwnode);
 	if (!bus)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/sfp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/sfp.c
@@ -208,6 +208,12 @@
  */
 #define SFP_PHY_ADDR	22
 
+/* SFP_EEPROM_BLOCK_SIZE is the size of data chunk to read the EEPROM
+ * at a time. Some SFP modules and also some Linux I2C drivers do not like
+ * reads longer than 16 bytes.
+ */
+#define SFP_EEPROM_BLOCK_SIZE	16
+
 struct sff_data {
 	unsigned int gpios;
 	bool (*module_supported)(const struct sfp_eeprom_id *id);
@@ -250,6 +256,7 @@
 	struct sfp_eeprom_id id;
 	unsigned int module_power_mW;
 	unsigned int module_t_start_up;
+	bool tx_fault_ignore;
 
 #if IS_ENABLED(CONFIG_HWMON)
 	struct sfp_diag diag;
@@ -1641,17 +1648,20 @@
 static int sfp_module_parse_power(struct sfp *sfp)
 {
 	u32 power_mW = 1000;
+	bool supports_a2;
 
 	if (sfp->id.ext.options & cpu_to_be16(SFP_OPTIONS_POWER_DECL))
 		power_mW = 1500;
 	if (sfp->id.ext.options & cpu_to_be16(SFP_OPTIONS_HIGH_POWER_LEVEL))
 		power_mW = 2000;
 
+	supports_a2 = sfp->id.ext.sff8472_compliance !=
+				SFP_SFF8472_COMPLIANCE_NONE ||
+		      sfp->id.ext.diagmon & SFP_DIAGMON_DDM;
+
 	if (power_mW > sfp->max_power_mW) {
 		/* Module power specification exceeds the allowed maximum. */
-		if (sfp->id.ext.sff8472_compliance ==
-			SFP_SFF8472_COMPLIANCE_NONE &&
-		    !(sfp->id.ext.diagmon & SFP_DIAGMON_DDM)) {
+		if (!supports_a2) {
 			/* The module appears not to implement bus address
 			 * 0xa2, so assume that the module powers up in the
 			 * indicated mode.
@@ -1668,11 +1678,25 @@
 		}
 	}
 
+	if (power_mW <= 1000) {
+		/* Modules below 1W do not require a power change sequence */
+		sfp->module_power_mW = power_mW;
+		return 0;
+	}
+
+	if (!supports_a2) {
+		/* The module power level is below the host maximum and the
+		 * module appears not to implement bus address 0xa2, so assume
+		 * that the module powers up in the indicated mode.
+		 */
+		return 0;
+	}
+
 	/* If the module requires a higher power mode, but also requires
 	 * an address change sequence, warn the user that the module may
 	 * not be functional.
 	 */
-	if (sfp->id.ext.diagmon & SFP_DIAGMON_ADDRMODE && power_mW > 1000) {
+	if (sfp->id.ext.diagmon & SFP_DIAGMON_ADDRMODE) {
 		dev_warn(sfp->dev,
 			 "Address Change Sequence not supported but module requires %u.%uW, module may not be functional\n",
 			 power_mW / 1000, (power_mW / 100) % 10);
@@ -1788,11 +1812,7 @@
 	u8 check;
 	int ret;
 
-	/* Some SFP modules and also some Linux I2C drivers do not like reads
-	 * longer than 16 bytes, so read the EEPROM in chunks of 16 bytes at
-	 * a time.
-	 */
-	sfp->i2c_block_size = 16;
+	sfp->i2c_block_size = SFP_EEPROM_BLOCK_SIZE;
 
 	ret = sfp_read(sfp, false, 0, &id.base, sizeof(id.base));
 	if (ret < 0) {
@@ -1928,6 +1948,12 @@
 	else
 		sfp->module_t_start_up = T_START_UP;
 
+	if (!memcmp(id.base.vendor_name, "HUAWEI          ", 16) &&
+	    !memcmp(id.base.vendor_pn, "MA5671A         ", 16))
+		sfp->tx_fault_ignore = true;
+	else
+		sfp->tx_fault_ignore = false;
+
 	return 0;
 }
 
@@ -1978,8 +2004,7 @@
 
 	/* Handle remove event globally, it resets this state machine */
 	if (event == SFP_E_REMOVE) {
-		if (sfp->sm_mod_state > SFP_MOD_PROBE)
-			sfp_sm_mod_remove(sfp);
+		sfp_sm_mod_remove(sfp);
 		sfp_sm_mod_next(sfp, SFP_MOD_EMPTY, 0);
 		return;
 	}
@@ -2380,7 +2405,10 @@
 	mutex_lock(&sfp->st_mutex);
 	state = sfp_get_state(sfp);
 	changed = state ^ sfp->state;
-	changed &= SFP_F_PRESENT | SFP_F_LOS | SFP_F_TX_FAULT;
+	if (sfp->tx_fault_ignore)
+		changed &= SFP_F_PRESENT | SFP_F_LOS;
+	else
+		changed &= SFP_F_PRESENT | SFP_F_LOS | SFP_F_TX_FAULT;
 
 	for (i = 0; i < GPIO_MAX; i++)
 		if (changed & BIT(i))
@@ -2435,6 +2463,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	sfp->dev = dev;
+	sfp->i2c_block_size = SFP_EEPROM_BLOCK_SIZE;
 
 	mutex_init(&sfp->sm_mutex);
 	mutex_init(&sfp->st_mutex);
@@ -2477,7 +2506,7 @@
 
 	platform_set_drvdata(pdev, sfp);
 
-	err = devm_add_action(sfp->dev, sfp_cleanup, sfp);
+	err = devm_add_action_or_reset(sfp->dev, sfp_cleanup, sfp);
 	if (err < 0)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/smsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/smsc.c
@@ -57,8 +57,6 @@
 
 static int smsc_phy_config_intr(struct phy_device *phydev)
 {
-	struct smsc_phy_priv *priv = phydev->priv;
-	u16 intmask = 0;
 	int rc;
 
 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
@@ -66,12 +64,10 @@
 		if (rc)
 			return rc;
 
-		intmask = MII_LAN83C185_ISF_INT4 | MII_LAN83C185_ISF_INT6;
-		if (priv->energy_enable)
-			intmask |= MII_LAN83C185_ISF_INT7;
-		rc = phy_write(phydev, MII_LAN83C185_IM, intmask);
+		rc = phy_write(phydev, MII_LAN83C185_IM,
+			       MII_LAN83C185_ISF_INT_PHYLIB_EVENTS);
 	} else {
-		rc = phy_write(phydev, MII_LAN83C185_IM, intmask);
+		rc = phy_write(phydev, MII_LAN83C185_IM, 0);
 		if (rc)
 			return rc;
 
@@ -83,13 +79,7 @@
 
 static irqreturn_t smsc_phy_handle_interrupt(struct phy_device *phydev)
 {
-	int irq_status, irq_enabled;
-
-	irq_enabled = phy_read(phydev, MII_LAN83C185_IM);
-	if (irq_enabled < 0) {
-		phy_error(phydev);
-		return IRQ_NONE;
-	}
+	int irq_status;
 
 	irq_status = phy_read(phydev, MII_LAN83C185_ISF);
 	if (irq_status < 0) {
@@ -97,7 +87,7 @@
 		return IRQ_NONE;
 	}
 
-	if (!(irq_status & irq_enabled))
+	if (!(irq_status & MII_LAN83C185_ISF_INT_PHYLIB_EVENTS))
 		return IRQ_NONE;
 
 	phy_trigger_machine(phydev);
@@ -110,7 +100,7 @@
 	struct smsc_phy_priv *priv = phydev->priv;
 	int rc;
 
-	if (!priv->energy_enable)
+	if (!priv->energy_enable || phydev->irq != PHY_POLL)
 		return 0;
 
 	rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
@@ -210,14 +200,19 @@
  * response on link pulses to detect presence of plugged Ethernet cable.
  * The Energy Detect Power-Down mode is enabled again in the end of procedure to
  * save approximately 220 mW of power if cable is unplugged.
+ * The workaround is only applicable to poll mode. Energy Detect Power-Down may
+ * not be used in interrupt mode lest link change detection becomes unreliable.
  */
 static int lan87xx_read_status(struct phy_device *phydev)
 {
 	struct smsc_phy_priv *priv = phydev->priv;
+	int err;
 
-	int err = genphy_read_status(phydev);
+	err = genphy_read_status(phydev);
+	if (err)
+		return err;
 
-	if (!phydev->link && priv->energy_enable) {
+	if (!phydev->link && priv->energy_enable && phydev->irq == PHY_POLL) {
 		/* Disable EDPD to wake up PHY */
 		int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
 		if (rc < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/vitesse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/vitesse.c
@@ -237,16 +237,6 @@
 	return 0;
 }
 
-static int vsc73xx_config_aneg(struct phy_device *phydev)
-{
-	/* The VSC73xx switches does not like to be instructed to
-	 * do autonegotiation in any way, it prefers that you just go
-	 * with the power-on/reset defaults. Writing some registers will
-	 * just make autonegotiation permanently fail.
-	 */
-	return 0;
-}
-
 /* This adds a skew for both TX and RX clocks, so the skew should only be
  * applied to "rgmii-id" interfaces. It may not work as expected
  * on "rgmii-txid", "rgmii-rxid" or "rgmii" interfaces.
@@ -444,7 +434,6 @@
 	.phy_id_mask    = 0x000ffff0,
 	/* PHY_GBIT_FEATURES */
 	.config_init    = vsc738x_config_init,
-	.config_aneg    = vsc73xx_config_aneg,
 	.read_page      = vsc73xx_read_page,
 	.write_page     = vsc73xx_write_page,
 }, {
@@ -453,7 +442,6 @@
 	.phy_id_mask    = 0x000ffff0,
 	/* PHY_GBIT_FEATURES */
 	.config_init    = vsc738x_config_init,
-	.config_aneg    = vsc73xx_config_aneg,
 	.read_page      = vsc73xx_read_page,
 	.write_page     = vsc73xx_write_page,
 }, {
@@ -462,7 +450,6 @@
 	.phy_id_mask    = 0x000ffff0,
 	/* PHY_GBIT_FEATURES */
 	.config_init    = vsc739x_config_init,
-	.config_aneg    = vsc73xx_config_aneg,
 	.read_page      = vsc73xx_read_page,
 	.write_page     = vsc73xx_write_page,
 }, {
@@ -471,7 +458,6 @@
 	.phy_id_mask    = 0x000ffff0,
 	/* PHY_GBIT_FEATURES */
 	.config_init    = vsc739x_config_init,
-	.config_aneg    = vsc73xx_config_aneg,
 	.read_page      = vsc73xx_read_page,
 	.write_page     = vsc73xx_write_page,
 }, {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/xilinx_gmii2rgmii.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/xilinx_gmii2rgmii.c
@@ -105,6 +105,7 @@
 
 	if (!priv->phy_dev->drv) {
 		dev_info(dev, "Attached phy not ready\n");
+		put_device(&priv->phy_dev->mdio.dev);
 		return -EPROBE_DEFER;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/phy/xilinx_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/phy/xilinx_phy.c
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Xilinx PCS/PMA Core phy driver
+ *
+ * Copyright (C) 2015 Xilinx, Inc.
+ *
+ * Description:
+ * This driver is developed for PCS/PMA Core.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+#include <linux/xilinx_phy.h>
+
+#define MII_PHY_STATUS_SPD_MASK		0x0C00
+#define MII_PHY_STATUS_FULLDUPLEX	0x1000
+#define MII_PHY_STATUS_1000		0x0800
+#define MII_PHY_STATUS_100		0x0400
+#define XPCSPMA_PHY_CTRL_ISOLATE_DISABLE 0xFBFF
+
+static int xilinxphy_read_status(struct phy_device *phydev)
+{
+	int err;
+	int status = 0;
+
+	/* Update the link, but return if there
+	 * was an error
+	 */
+	err = genphy_update_link(phydev);
+	if (err)
+		return err;
+
+	if (phydev->autoneg == AUTONEG_ENABLE) {
+		status = phy_read(phydev, MII_LPA);
+
+		if (status & MII_PHY_STATUS_FULLDUPLEX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+
+		switch (status & MII_PHY_STATUS_SPD_MASK) {
+		case MII_PHY_STATUS_1000:
+			phydev->speed = SPEED_1000;
+			break;
+
+		case MII_PHY_STATUS_100:
+			phydev->speed = SPEED_100;
+			break;
+
+		default:
+			phydev->speed = SPEED_10;
+			break;
+		}
+	} else {
+		int bmcr = phy_read(phydev, MII_BMCR);
+
+		if (bmcr < 0)
+			return bmcr;
+
+		if (bmcr & BMCR_FULLDPLX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+
+		if (bmcr & BMCR_SPEED1000)
+			phydev->speed = SPEED_1000;
+		else if (bmcr & BMCR_SPEED100)
+			phydev->speed = SPEED_100;
+		else
+			phydev->speed = SPEED_10;
+	}
+
+	/* For 1000BASE-X Phy Mode the speed/duplex will always be
+	 * 1000Mbps/fullduplex
+	 */
+	if (phydev->dev_flags == XAE_PHY_TYPE_1000BASE_X) {
+		phydev->duplex = DUPLEX_FULL;
+		phydev->speed = SPEED_1000;
+	}
+
+	/* For 2500BASE-X Phy Mode the speed/duplex will always be
+	 * 2500Mbps/fullduplex
+	 */
+	if (phydev->dev_flags == XAE_PHY_TYPE_2500) {
+		phydev->duplex = DUPLEX_FULL;
+		phydev->speed = SPEED_2500;
+	}
+
+	return 0;
+}
+
+static int xilinxphy_of_init(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct device_node *of_node = dev->of_node;
+	u32 phytype;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return 0;
+
+	if (!of_node)
+		return -ENODEV;
+
+	if (!of_property_read_u32(of_node, "xlnx,phy-type", &phytype)) {
+		if (phytype == XAE_PHY_TYPE_1000BASE_X)
+			phydev->dev_flags |= XAE_PHY_TYPE_1000BASE_X;
+		if (phytype == XAE_PHY_TYPE_2500)
+			phydev->dev_flags |= XAE_PHY_TYPE_2500;
+	}
+
+	return 0;
+}
+
+static int xilinxphy_config_init(struct phy_device *phydev)
+{
+	int temp;
+
+	xilinxphy_of_init(phydev);
+	temp = phy_read(phydev, MII_BMCR);
+	temp &= XPCSPMA_PHY_CTRL_ISOLATE_DISABLE;
+	phy_write(phydev, MII_BMCR, temp);
+
+	return 0;
+}
+
+static struct phy_driver xilinx_drivers[] = {
+	{
+		.phy_id = XILINX_PHY_ID,
+		.phy_id_mask = XILINX_PHY_ID_MASK,
+		.name = "Xilinx PCS/PMA PHY",
+		.flags = PHY_RST_AFTER_CLK_EN,
+		.features = PHY_GBIT_FEATURES,
+		.config_init = &xilinxphy_config_init,
+		.config_aneg = &genphy_config_aneg,
+		.read_status = &xilinxphy_read_status,
+		.resume = &genphy_resume,
+		.suspend = &genphy_suspend,
+	},
+};
+
+module_phy_driver(xilinx_drivers);
+
+static struct mdio_device_id __maybe_unused xilinx_tbl[] = {
+	{ XILINX_PHY_ID, XILINX_PHY_ID_MASK },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, xilinx_tbl);
+MODULE_DESCRIPTION("Xilinx PCS/PMA PHY driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/plip/plip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/plip/plip.c
@@ -446,12 +446,12 @@
 	}
 	rcv->state = PLIP_PK_DONE;
 	if (rcv->skb) {
-		kfree_skb(rcv->skb);
+		dev_kfree_skb_irq(rcv->skb);
 		rcv->skb = NULL;
 	}
 	snd->state = PLIP_PK_DONE;
 	if (snd->skb) {
-		dev_kfree_skb(snd->skb);
+		dev_consume_skb_irq(snd->skb);
 		snd->skb = NULL;
 	}
 	spin_unlock_irq(&nl->lock);
@@ -811,7 +811,7 @@
 				return HS_TIMEOUT;
 			}
 		}
-		break;
+		fallthrough;
 
 	case PLIP_PK_LENGTH_LSB:
 		if (plip_send(nibble_timeout, dev,
@@ -1107,7 +1107,7 @@
 		/* Any address will do - we take the first. We already
 		   have the first two bytes filled with 0xfc, from
 		   plip_init_dev(). */
-		const struct in_ifaddr *ifa = rcu_dereference(in_dev->ifa_list);
+		const struct in_ifaddr *ifa = rtnl_dereference(in_dev->ifa_list);
 		if (ifa != NULL) {
 			memcpy(dev->dev_addr+2, &ifa->ifa_local, 4);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ppp/ppp_async.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ppp/ppp_async.c
@@ -471,6 +471,10 @@
 	case PPPIOCSMRU:
 		if (get_user(val, p))
 			break;
+		if (val > U16_MAX) {
+			err = -EINVAL;
+			break;
+		}
 		if (val < PPP_MRU)
 			val = PPP_MRU;
 		ap->mru = val;
@@ -548,7 +552,7 @@
 	 * and 7 (code-reject) must be sent as though no options
 	 * had been negotiated.
 	 */
-	islcp = proto == PPP_LCP && 1 <= data[2] && data[2] <= 7;
+	islcp = proto == PPP_LCP && count >= 3 && 1 <= data[2] && data[2] <= 7;
 
 	if (i == 0) {
 		if (islcp)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ppp/ppp_generic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ppp/ppp_generic.c
@@ -69,6 +69,20 @@
 #define MPHDRLEN	6	/* multilink protocol header length */
 #define MPHDRLEN_SSN	4	/* ditto with short sequence numbers */
 
+#define PPP_PROTO_LEN	2
+#define PPP_LCP_HDRLEN	4
+
+/* The filter instructions generated by libpcap are constructed
+ * assuming a four-byte PPP header on each packet, where the last
+ * 2 bytes are the protocol field defined in the RFC and the first
+ * byte of the first 2 bytes indicates the direction.
+ * The second byte is currently unused, but we still need to initialize
+ * it to prevent crafted BPF programs from reading them which would
+ * cause reading of uninitialized data.
+ */
+#define PPP_FILTER_OUTBOUND_TAG 0x0100
+#define PPP_FILTER_INBOUND_TAG  0x0000
+
 /*
  * An instance of /dev/ppp can be associated with either a ppp
  * interface unit or a ppp channel.  In both cases, file->private_data
@@ -488,6 +502,15 @@
 	return ret;
 }
 
+static bool ppp_check_packet(struct sk_buff *skb, size_t count)
+{
+	/* LCP packets must include LCP header which 4 bytes long:
+	 * 1-byte code, 1-byte identifier, and 2-byte length.
+	 */
+	return get_unaligned_be16(skb->data) != PPP_LCP ||
+		count >= PPP_PROTO_LEN + PPP_LCP_HDRLEN;
+}
+
 static ssize_t ppp_write(struct file *file, const char __user *buf,
 			 size_t count, loff_t *ppos)
 {
@@ -497,6 +520,9 @@
 
 	if (!pf)
 		return -ENXIO;
+	/* All PPP packets should start with the 2-byte protocol */
+	if (count < PPP_PROTO_LEN)
+		return -EINVAL;
 	ret = -ENOMEM;
 	skb = alloc_skb(count + pf->hdrlen, GFP_KERNEL);
 	if (!skb)
@@ -507,6 +533,11 @@
 		kfree_skb(skb);
 		goto out;
 	}
+	ret = -EINVAL;
+	if (unlikely(!ppp_check_packet(skb, count))) {
+		kfree_skb(skb);
+		goto out;
+	}
 
 	switch (pf->kind) {
 	case INTERFACE:
@@ -1737,12 +1768,14 @@
 	int len;
 	unsigned char *cp;
 
+	skb->dev = ppp->dev;
+
 	if (proto < 0x8000) {
 #ifdef CONFIG_PPP_FILTER
-		/* check if we should pass this packet */
-		/* the filter instructions are constructed assuming
-		   a four-byte PPP header on each packet */
-		*(u8 *)skb_push(skb, 2) = 1;
+		/* check if the packet passes the pass and active filters.
+		 * See comment for PPP_FILTER_OUTBOUND_TAG above.
+		 */
+		*(__be16 *)skb_push(skb, 2) = htons(PPP_FILTER_OUTBOUND_TAG);
 		if (ppp->pass_filter &&
 		    bpf_prog_run(ppp->pass_filter, skb) == 0) {
 			if (ppp->debug & 1)
@@ -1764,7 +1797,7 @@
 	}
 
 	++ppp->stats64.tx_packets;
-	ppp->stats64.tx_bytes += skb->len - 2;
+	ppp->stats64.tx_bytes += skb->len - PPP_PROTO_LEN;
 
 	switch (proto) {
 	case PPP_IP:
@@ -2246,7 +2279,7 @@
 	if (!pchb)
 		goto out_rcu;
 
-	spin_lock(&pchb->downl);
+	spin_lock_bh(&pchb->downl);
 	if (!pchb->chan) {
 		/* channel got unregistered */
 		kfree_skb(skb);
@@ -2258,7 +2291,7 @@
 		kfree_skb(skb);
 
 outl:
-	spin_unlock(&pchb->downl);
+	spin_unlock_bh(&pchb->downl);
 out_rcu:
 	rcu_read_unlock();
 
@@ -2459,14 +2492,13 @@
 		/* network protocol frame - give it to the kernel */
 
 #ifdef CONFIG_PPP_FILTER
-		/* check if the packet passes the pass and active filters */
-		/* the filter instructions are constructed assuming
-		   a four-byte PPP header on each packet */
 		if (ppp->pass_filter || ppp->active_filter) {
 			if (skb_unclone(skb, GFP_ATOMIC))
 				goto err;
-
-			*(u8 *)skb_push(skb, 2) = 0;
+			/* Check if the packet passes the pass and active filters.
+			 * See comment for PPP_FILTER_INBOUND_TAG above.
+			 */
+			*(__be16 *)skb_push(skb, 2) = htons(PPP_FILTER_INBOUND_TAG);
 			if (ppp->pass_filter &&
 			    bpf_prog_run(ppp->pass_filter, skb) == 0) {
 				if (ppp->debug & 1)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ppp/ppp_synctty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ppp/ppp_synctty.c
@@ -464,6 +464,10 @@
 	case PPPIOCSMRU:
 		if (get_user(val, (int __user *) argp))
 			break;
+		if (val > U16_MAX) {
+			err = -EINVAL;
+			break;
+		}
 		if (val < PPP_MRU)
 			val = PPP_MRU;
 		ap->mru = val;
@@ -699,7 +703,7 @@
 
 	/* strip address/control field if present */
 	p = skb->data;
-	if (p[0] == PPP_ALLSTATIONS && p[1] == PPP_UI) {
+	if (skb->len >= 2 && p[0] == PPP_ALLSTATIONS && p[1] == PPP_UI) {
 		/* chop off address/control */
 		if (skb->len < 3)
 			goto err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ppp/pppoe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ppp/pppoe.c
@@ -988,6 +988,7 @@
 	path->encap.proto = htons(ETH_P_PPP_SES);
 	path->encap.id = be16_to_cpu(po->num);
 	memcpy(path->encap.h_dest, po->pppoe_pa.remote, ETH_ALEN);
+	memcpy(ctx->daddr, po->pppoe_pa.remote, ETH_ALEN);
 	path->dev = ctx->dev;
 	ctx->dev = dev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/ppp/pptp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/ppp/pptp.c
@@ -24,6 +24,7 @@
 #include <linux/in.h>
 #include <linux/ip.h>
 #include <linux/rcupdate.h>
+#include <linux/security.h>
 #include <linux/spinlock.h>
 
 #include <net/sock.h>
@@ -128,6 +129,23 @@
 	spin_unlock(&chan_lock);
 }
 
+static struct rtable *pptp_route_output(struct pppox_sock *po,
+					struct flowi4 *fl4)
+{
+	struct sock *sk = &po->sk;
+	struct net *net;
+
+	net = sock_net(sk);
+	flowi4_init_output(fl4, sk->sk_bound_dev_if, sk->sk_mark, 0,
+			   RT_SCOPE_UNIVERSE, IPPROTO_GRE, 0,
+			   po->proto.pptp.dst_addr.sin_addr.s_addr,
+			   po->proto.pptp.src_addr.sin_addr.s_addr,
+			   0, 0, sock_net_uid(net, sk));
+	security_sk_classify_flow(sk, flowi4_to_flowi_common(fl4));
+
+	return ip_route_output_flow(net, fl4, sk);
+}
+
 static int pptp_xmit(struct ppp_channel *chan, struct sk_buff *skb)
 {
 	struct sock *sk = (struct sock *) chan->private;
@@ -151,11 +169,7 @@
 	if (sk_pppox(po)->sk_state & PPPOX_DEAD)
 		goto tx_error;
 
-	rt = ip_route_output_ports(net, &fl4, NULL,
-				   opt->dst_addr.sin_addr.s_addr,
-				   opt->src_addr.sin_addr.s_addr,
-				   0, 0, IPPROTO_GRE,
-				   RT_TOS(0), sk->sk_bound_dev_if);
+	rt = pptp_route_output(po, &fl4);
 	if (IS_ERR(rt))
 		goto tx_error;
 
@@ -438,12 +452,7 @@
 	po->chan.private = sk;
 	po->chan.ops = &pptp_chan_ops;
 
-	rt = ip_route_output_ports(sock_net(sk), &fl4, sk,
-				   opt->dst_addr.sin_addr.s_addr,
-				   opt->src_addr.sin_addr.s_addr,
-				   0, 0,
-				   IPPROTO_GRE, RT_CONN_FLAGS(sk),
-				   sk->sk_bound_dev_if);
+	rt = pptp_route_output(po, &fl4);
 	if (IS_ERR(rt)) {
 		error = -EHOSTUNREACH;
 		goto end;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/slip/slhc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/slip/slhc.c
@@ -643,46 +643,57 @@
 int
 slhc_remember(struct slcompress *comp, unsigned char *icp, int isize)
 {
-	struct cstate *cs;
-	unsigned ihl;
-
+	const struct tcphdr *th;
 	unsigned char index;
+	struct iphdr *iph;
+	struct cstate *cs;
+	unsigned int ihl;
 
-	if(isize < 20) {
-		/* The packet is shorter than a legal IP header */
+	/* The packet is shorter than a legal IP header.
+	 * Also make sure isize is positive.
+	 */
+	if (isize < (int)sizeof(struct iphdr)) {
+runt:
 		comp->sls_i_runt++;
-		return slhc_toss( comp );
+		return slhc_toss(comp);
 	}
+	iph = (struct iphdr *)icp;
 	/* Peek at the IP header's IHL field to find its length */
-	ihl = icp[0] & 0xf;
-	if(ihl < 20 / 4){
-		/* The IP header length field is too small */
-		comp->sls_i_runt++;
-		return slhc_toss( comp );
-	}
-	index = icp[9];
-	icp[9] = IPPROTO_TCP;
+	ihl = iph->ihl;
+	/* The IP header length field is too small,
+	 * or packet is shorter than the IP header followed
+	 * by minimal tcp header.
+	 */
+	if (ihl < 5 || isize < ihl * 4 + sizeof(struct tcphdr))
+		goto runt;
+
+	index = iph->protocol;
+	iph->protocol = IPPROTO_TCP;
 
 	if (ip_fast_csum(icp, ihl)) {
 		/* Bad IP header checksum; discard */
 		comp->sls_i_badcheck++;
-		return slhc_toss( comp );
+		return slhc_toss(comp);
 	}
-	if(index > comp->rslot_limit) {
+	if (index > comp->rslot_limit) {
 		comp->sls_i_error++;
 		return slhc_toss(comp);
 	}
-
+	th = (struct tcphdr *)(icp + ihl * 4);
+	if (th->doff < sizeof(struct tcphdr) / 4)
+		goto runt;
+	if (isize < ihl * 4 + th->doff * 4)
+		goto runt;
 	/* Update local state */
 	cs = &comp->rstate[comp->recv_current = index];
 	comp->flags &=~ SLF_TOSS;
-	memcpy(&cs->cs_ip,icp,20);
-	memcpy(&cs->cs_tcp,icp + ihl*4,20);
+	memcpy(&cs->cs_ip, iph, sizeof(*iph));
+	memcpy(&cs->cs_tcp, th, sizeof(*th));
 	if (ihl > 5)
-	  memcpy(cs->cs_ipopt, icp + sizeof(struct iphdr), (ihl - 5) * 4);
-	if (cs->cs_tcp.doff > 5)
-	  memcpy(cs->cs_tcpopt, icp + ihl*4 + sizeof(struct tcphdr), (cs->cs_tcp.doff - 5) * 4);
-	cs->cs_hsize = ihl*2 + cs->cs_tcp.doff*2;
+	  memcpy(cs->cs_ipopt, &iph[1], (ihl - 5) * 4);
+	if (th->doff > 5)
+	  memcpy(cs->cs_tcpopt, &th[1], (th->doff - 5) * 4);
+	cs->cs_hsize = ihl*2 + th->doff*2;
 	cs->initialized = true;
 	/* Put headers back on packet
 	 * Neither header checksum is recalculated
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/slip/slip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/slip/slip.c
@@ -469,7 +469,7 @@
 	spin_lock(&sl->lock);
 
 	if (netif_queue_stopped(dev)) {
-		if (!netif_running(dev))
+		if (!netif_running(dev) || !sl->tty)
 			goto out;
 
 		/* May be we must check transmitter timeout here ?
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/slip/slip.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/slip/slip.h
@@ -40,6 +40,8 @@
 					   insmod -oslip_maxdev=nnn	*/
 #define SL_MTU		296		/* 296; I am used to 600- FvK	*/
 
+/* some arch define END as assembly function ending, just undef it */
+#undef	END
 /* SLIP protocol characters. */
 #define END             0300		/* indicates end of frame	*/
 #define ESC             0333		/* indicates byte stuffing	*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/sungem_phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/sungem_phy.c
@@ -454,6 +454,7 @@
 		int can_low_power = 1;
 		if (np == NULL || of_get_property(np, "no-autolowpower", NULL))
 			can_low_power = 0;
+		of_node_put(np);
 		if (can_low_power) {
 			/* Enable automatic low-power */
 			sungem_phy_write(phy, 0x1c, 0x9002);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/tap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/tap.c
@@ -523,7 +523,7 @@
 	q->sock.state = SS_CONNECTED;
 	q->sock.file = file;
 	q->sock.ops = &tap_socket_ops;
-	sock_init_data(&q->sock, &q->sk);
+	sock_init_data_uid(&q->sock, &q->sk, current_fsuid());
 	q->sk.sk_write_space = tap_sock_write_space;
 	q->sk.sk_destruct = tap_sock_destruct;
 	q->flags = IFF_VNET_HDR | IFF_NO_PI | IFF_TAP;
@@ -714,7 +714,7 @@
 
 	/* Move network header to the right position for VLAN tagged packets */
 	if (eth_type_vlan(skb->protocol) &&
-	    __vlan_get_protocol(skb, skb->protocol, &depth) != 0)
+	    vlan_get_protocol_and_depth(skb, skb->protocol, &depth) != 0)
 		skb_set_network_header(skb, depth);
 
 	rcu_read_lock();
@@ -1139,6 +1139,11 @@
 	struct sk_buff *skb;
 	int err, depth;
 
+	if (unlikely(xdp->data_end - xdp->data < ETH_HLEN)) {
+		err = -EINVAL;
+		goto err;
+	}
+
 	if (q->flags & IFF_VNET_HDR)
 		vnet_hdr_len = READ_ONCE(q->vnet_hdr_sz);
 
@@ -1163,7 +1168,7 @@
 
 	/* Move network header to the right position for VLAN tagged packets */
 	if (eth_type_vlan(skb->protocol) &&
-	    __vlan_get_protocol(skb, skb->protocol, &depth) != 0)
+	    vlan_get_protocol_and_depth(skb, skb->protocol, &depth) != 0)
 		skb_set_network_header(skb, depth);
 
 	rcu_read_lock();
@@ -1198,7 +1203,8 @@
 	struct xdp_buff *xdp;
 	int i;
 
-	if (ctl && (ctl->type == TUN_MSG_PTR)) {
+	if (m->msg_controllen == sizeof(struct tun_msg_ctl) &&
+	    ctl && ctl->type == TUN_MSG_PTR) {
 		for (i = 0; i < ctl->num; i++) {
 			xdp = &((struct xdp_buff *)ctl->ptr)[i];
 			tap_get_user_xdp(q, xdp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/team/team.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/team/team.c
@@ -285,8 +285,10 @@
 	return 0;
 
 inst_rollback:
-	for (i--; i >= 0; i--)
+	for (i--; i >= 0; i--) {
 		__team_option_inst_del_option(team, dst_opts[i]);
+		list_del(&dst_opts[i]->list);
+	}
 
 	i = option_count;
 alloc_rollback:
@@ -977,7 +979,8 @@
 
 #define TEAM_VLAN_FEATURES (NETIF_F_HW_CSUM | NETIF_F_SG | \
 			    NETIF_F_FRAGLIST | NETIF_F_GSO_SOFTWARE | \
-			    NETIF_F_HIGHDMA | NETIF_F_LRO)
+			    NETIF_F_HIGHDMA | NETIF_F_LRO | \
+			    NETIF_F_GSO_ENCAP_ALL)
 
 #define TEAM_ENC_FEATURES	(NETIF_F_HW_CSUM | NETIF_F_SG | \
 				 NETIF_F_RXCSUM | NETIF_F_GSO_SOFTWARE)
@@ -1163,6 +1166,13 @@
 		return -EBUSY;
 	}
 
+	if (netdev_has_upper_dev(port_dev, dev)) {
+		NL_SET_ERR_MSG(extack, "Device is already a lower device of the team interface");
+		netdev_err(dev, "Device %s is already a lower device of the team interface\n",
+			   portname);
+		return -EBUSY;
+	}
+
 	if (port_dev->features & NETIF_F_VLAN_CHALLENGED &&
 	    vlan_uses_dev(dev)) {
 		NL_SET_ERR_MSG(extack, "Device is VLAN challenged and team device has VLAN set up");
@@ -1270,10 +1280,12 @@
 		}
 	}
 
-	netif_addr_lock_bh(dev);
-	dev_uc_sync_multiple(port_dev, dev);
-	dev_mc_sync_multiple(port_dev, dev);
-	netif_addr_unlock_bh(dev);
+	if (dev->flags & IFF_UP) {
+		netif_addr_lock_bh(dev);
+		dev_uc_sync_multiple(port_dev, dev);
+		dev_mc_sync_multiple(port_dev, dev);
+		netif_addr_unlock_bh(dev);
+	}
 
 	port->index = -1;
 	list_add_tail_rcu(&port->list, &team->port_list);
@@ -1344,8 +1356,10 @@
 	netdev_rx_handler_unregister(port_dev);
 	team_port_disable_netpoll(port);
 	vlan_vids_del_by_dev(port_dev, dev);
-	dev_uc_unsync(port_dev, dev);
-	dev_mc_unsync(port_dev, dev);
+	if (dev->flags & IFF_UP) {
+		dev_uc_unsync(port_dev, dev);
+		dev_mc_unsync(port_dev, dev);
+	}
 	dev_close(port_dev);
 	team_port_leave(team, port);
 
@@ -1620,6 +1634,7 @@
 
 	team->dev = dev;
 	team_set_no_mode(team);
+	team->notifier_ctx = false;
 
 	team->pcpu_stats = netdev_alloc_pcpu_stats(struct team_pcpu_stats);
 	if (!team->pcpu_stats)
@@ -1695,6 +1710,14 @@
 
 static int team_close(struct net_device *dev)
 {
+	struct team *team = netdev_priv(dev);
+	struct team_port *port;
+
+	list_for_each_entry(port, &team->port_list, list) {
+		dev_uc_unsync(port->dev, dev);
+		dev_mc_unsync(port->dev, dev);
+	}
+
 	return 0;
 }
 
@@ -2109,7 +2132,12 @@
 static void team_setup_by_port(struct net_device *dev,
 			       struct net_device *port_dev)
 {
-	dev->header_ops	= port_dev->header_ops;
+	struct team *team = netdev_priv(dev);
+
+	if (port_dev->type == ARPHRD_ETHER)
+		dev->header_ops	= team->header_ops_cache;
+	else
+		dev->header_ops	= port_dev->header_ops;
 	dev->type = port_dev->type;
 	dev->hard_header_len = port_dev->hard_header_len;
 	dev->needed_headroom = port_dev->needed_headroom;
@@ -2117,6 +2145,15 @@
 	dev->mtu = port_dev->mtu;
 	memcpy(dev->broadcast, port_dev->broadcast, port_dev->addr_len);
 	eth_hw_addr_inherit(dev, port_dev);
+
+	if (port_dev->flags & IFF_POINTOPOINT) {
+		dev->flags &= ~(IFF_BROADCAST | IFF_MULTICAST);
+		dev->flags |= (IFF_POINTOPOINT | IFF_NOARP);
+	} else if ((port_dev->flags & (IFF_BROADCAST | IFF_MULTICAST)) ==
+		    (IFF_BROADCAST | IFF_MULTICAST)) {
+		dev->flags |= (IFF_BROADCAST | IFF_MULTICAST);
+		dev->flags &= ~(IFF_POINTOPOINT | IFF_NOARP);
+	}
 }
 
 static int team_dev_type_check_change(struct net_device *dev,
@@ -2147,8 +2184,11 @@
 
 static void team_setup(struct net_device *dev)
 {
+	struct team *team = netdev_priv(dev);
+
 	ether_setup(dev);
 	dev->max_mtu = ETH_MAX_MTU;
+	team->header_ops_cache = dev->header_ops;
 
 	dev->netdev_ops = &team_netdev_ops;
 	dev->ethtool_ops = &team_ethtool_ops;
@@ -2173,7 +2213,9 @@
 
 	dev->hw_features = TEAM_VLAN_FEATURES |
 			   NETIF_F_HW_VLAN_CTAG_RX |
-			   NETIF_F_HW_VLAN_CTAG_FILTER;
+			   NETIF_F_HW_VLAN_CTAG_FILTER |
+			   NETIF_F_HW_VLAN_STAG_RX |
+			   NETIF_F_HW_VLAN_STAG_FILTER;
 
 	dev->hw_features |= NETIF_F_GSO_ENCAP_ALL;
 	dev->features |= dev->hw_features;
@@ -2623,7 +2665,9 @@
 				ctx.data.u32_val = nla_get_u32(attr_data);
 				break;
 			case TEAM_OPTION_TYPE_STRING:
-				if (nla_len(attr_data) > TEAM_STRING_MAX_LEN) {
+				if (nla_len(attr_data) > TEAM_STRING_MAX_LEN ||
+				    !memchr(nla_data(attr_data), '\0',
+					    nla_len(attr_data))) {
 					err = -EINVAL;
 					goto team_put;
 				}
@@ -3004,7 +3048,11 @@
 		team_del_slave(port->team->dev, dev);
 		break;
 	case NETDEV_FEAT_CHANGE:
-		team_compute_features(port->team);
+		if (!port->team->notifier_ctx) {
+			port->team->notifier_ctx = true;
+			team_compute_features(port->team);
+			port->team->notifier_ctx = false;
+		}
 		break;
 	case NETDEV_PRECHANGEMTU:
 		/* Forbid to change mtu of underlaying device */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/thunderbolt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/thunderbolt.c
@@ -612,18 +612,13 @@
 		return;
 	}
 
-	/* Both logins successful so enable the high-speed DMA paths and
-	 * start the network device queue.
+	/* Both logins successful so enable the rings, high-speed DMA
+	 * paths and start the network device queue.
+	 *
+	 * Note we enable the DMA paths last to make sure we have primed
+	 * the Rx ring before any incoming packets are allowed to
+	 * arrive.
 	 */
-	ret = tb_xdomain_enable_paths(net->xd, net->local_transmit_path,
-				      net->rx_ring.ring->hop,
-				      net->remote_transmit_path,
-				      net->tx_ring.ring->hop);
-	if (ret) {
-		netdev_err(net->dev, "failed to enable DMA paths\n");
-		return;
-	}
-
 	tb_ring_start(net->tx_ring.ring);
 	tb_ring_start(net->rx_ring.ring);
 
@@ -635,10 +630,21 @@
 	if (ret)
 		goto err_free_rx_buffers;
 
+	ret = tb_xdomain_enable_paths(net->xd, net->local_transmit_path,
+				      net->rx_ring.ring->hop,
+				      net->remote_transmit_path,
+				      net->tx_ring.ring->hop);
+	if (ret) {
+		netdev_err(net->dev, "failed to enable DMA paths\n");
+		goto err_free_tx_buffers;
+	}
+
 	netif_carrier_on(net->dev);
 	netif_start_queue(net->dev);
 	return;
 
+err_free_tx_buffers:
+	tbnet_free_buffers(&net->tx_ring);
 err_free_rx_buffers:
 	tbnet_free_buffers(&net->rx_ring);
 err_stop_rings:
@@ -896,6 +902,7 @@
 				tbnet_start_poll, net);
 	if (!ring) {
 		netdev_err(dev, "failed to allocate Rx ring\n");
+		tb_xdomain_release_out_hopid(xd, hopid);
 		tb_ring_free(net->tx_ring.ring);
 		net->tx_ring.ring = NULL;
 		return -ENOMEM;
@@ -986,12 +993,11 @@
 		*tucso = ~csum_tcpudp_magic(ip_hdr(skb)->saddr,
 					    ip_hdr(skb)->daddr, 0,
 					    ip_hdr(skb)->protocol, 0);
-	} else if (skb_is_gso_v6(skb)) {
+	} else if (skb_is_gso(skb) && skb_is_gso_v6(skb)) {
 		tucso = dest + ((void *)&(tcp_hdr(skb)->check) - data);
 		*tucso = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
 					  &ipv6_hdr(skb)->daddr, 0,
 					  IPPROTO_TCP, 0);
-		return false;
 	} else if (protocol == htons(ETH_P_IPV6)) {
 		tucso = dest + skb_checksum_start_offset(skb) + skb->csum_offset;
 		*tucso = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
@@ -1371,12 +1377,21 @@
 				  TBNET_MATCH_FRAGS_ID | TBNET_64K_FRAMES);
 
 	ret = tb_register_property_dir("network", tbnet_dir);
-	if (ret) {
-		tb_property_free_dir(tbnet_dir);
-		return ret;
-	}
+	if (ret)
+		goto err_free_dir;
+
+	ret = tb_register_service_driver(&tbnet_driver);
+	if (ret)
+		goto err_unregister;
+
+	return 0;
+
+err_unregister:
+	tb_unregister_property_dir("network", tbnet_dir);
+err_free_dir:
+	tb_property_free_dir(tbnet_dir);
 
-	return tb_register_service_driver(&tbnet_driver);
+	return ret;
 }
 module_init(tbnet_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/tun.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/tun.c
@@ -209,6 +209,9 @@
 	struct tun_prog __rcu *steering_prog;
 	struct tun_prog __rcu *filter_prog;
 	struct ethtool_link_ksettings link_ksettings;
+	/* init args */
+	struct file *file;
+	struct ifreq *ifr;
 };
 
 struct veth {
@@ -216,6 +219,9 @@
 	__be16 h_vlan_TCI;
 };
 
+static void tun_flow_init(struct tun_struct *tun);
+static void tun_flow_uninit(struct tun_struct *tun);
+
 static int tun_napi_receive(struct napi_struct *napi, int budget)
 {
 	struct tun_file *tfile = container_of(napi, struct tun_file, napi);
@@ -268,6 +274,12 @@
 	}
 }
 
+static void tun_napi_enable(struct tun_file *tfile)
+{
+	if (tfile->napi_enabled)
+		napi_enable(&tfile->napi);
+}
+
 static void tun_napi_disable(struct tun_file *tfile)
 {
 	if (tfile->napi_enabled)
@@ -569,7 +581,7 @@
 	struct net *net = dev_net(tun->dev);
 
 	return ((uid_valid(tun->owner) && !uid_eq(cred->euid, tun->owner)) ||
-		  (gid_valid(tun->group) && !in_egroup_p(tun->group))) &&
+		(gid_valid(tun->group) && !in_egroup_p(tun->group))) &&
 		!ns_capable(net->user_ns, CAP_NET_ADMIN);
 }
 
@@ -629,7 +641,8 @@
 	tun = rtnl_dereference(tfile->tun);
 
 	if (tun && clean) {
-		tun_napi_disable(tfile);
+		if (!tfile->detached)
+			tun_napi_disable(tfile);
 		tun_napi_del(tfile);
 	}
 
@@ -641,6 +654,7 @@
 				   tun->tfiles[tun->numqueues - 1]);
 		ntfile = rtnl_dereference(tun->tfiles[index]);
 		ntfile->queue_index = index;
+		ntfile->xdp_rxq.queue_index = index;
 		rcu_assign_pointer(tun->tfiles[tun->numqueues - 1],
 				   NULL);
 
@@ -648,8 +662,10 @@
 		if (clean) {
 			RCU_INIT_POINTER(tfile->tun, NULL);
 			sock_put(&tfile->sk);
-		} else
+		} else {
 			tun_disable_queue(tun, tfile);
+			tun_napi_disable(tfile);
+		}
 
 		synchronize_net();
 		tun_flow_delete_by_queue(tun, tun->numqueues + 1);
@@ -672,7 +688,6 @@
 		if (tun)
 			xdp_rxq_info_unreg(&tfile->xdp_rxq);
 		ptr_ring_cleanup(&tfile->tx_ring, tun_ptr_free);
-		sock_put(&tfile->sk);
 	}
 }
 
@@ -688,6 +703,9 @@
 	if (dev)
 		netdev_state_change(dev);
 	rtnl_unlock();
+
+	if (clean)
+		sock_put(&tfile->sk);
 }
 
 static void tun_detach_all(struct net_device *dev)
@@ -722,6 +740,7 @@
 		sock_put(&tfile->sk);
 	}
 	list_for_each_entry_safe(tfile, tmp, &tun->disabled, next) {
+		tun_napi_del(tfile);
 		tun_enable_queue(tfile);
 		tun_queue_purge(tfile);
 		xdp_rxq_info_unreg(&tfile->xdp_rxq);
@@ -802,6 +821,7 @@
 
 	if (tfile->detached) {
 		tun_enable_queue(tfile);
+		tun_napi_enable(tfile);
 	} else {
 		sock_hold(&tfile->sk);
 		tun_napi_init(tun, tfile, napi, napi_frags);
@@ -953,6 +973,49 @@
 
 static const struct ethtool_ops tun_ethtool_ops;
 
+static int tun_net_init(struct net_device *dev)
+{
+	struct tun_struct *tun = netdev_priv(dev);
+	struct ifreq *ifr = tun->ifr;
+	int err;
+
+	dev->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
+	if (!dev->tstats)
+		return -ENOMEM;
+
+	spin_lock_init(&tun->lock);
+
+	err = security_tun_dev_alloc_security(&tun->security);
+	if (err < 0) {
+		free_percpu(dev->tstats);
+		return err;
+	}
+
+	tun_flow_init(tun);
+
+	dev->hw_features = NETIF_F_SG | NETIF_F_FRAGLIST |
+			   TUN_USER_FEATURES | NETIF_F_HW_VLAN_CTAG_TX |
+			   NETIF_F_HW_VLAN_STAG_TX;
+	dev->features = dev->hw_features | NETIF_F_LLTX;
+	dev->vlan_features = dev->features &
+			     ~(NETIF_F_HW_VLAN_CTAG_TX |
+			       NETIF_F_HW_VLAN_STAG_TX);
+
+	tun->flags = (tun->flags & ~TUN_FEATURES) |
+		      (ifr->ifr_flags & TUN_FEATURES);
+
+	INIT_LIST_HEAD(&tun->disabled);
+	err = tun_attach(tun, tun->file, false, ifr->ifr_flags & IFF_NAPI,
+			 ifr->ifr_flags & IFF_NAPI_FRAGS, false);
+	if (err < 0) {
+		tun_flow_uninit(tun);
+		security_tun_dev_free_security(tun->security);
+		free_percpu(dev->tstats);
+		return err;
+	}
+	return 0;
+}
+
 /* Net device detach from fd. */
 static void tun_net_uninit(struct net_device *dev)
 {
@@ -1010,6 +1073,7 @@
 {
 	struct tun_struct *tun = netdev_priv(dev);
 	int txq = skb->queue_mapping;
+	struct netdev_queue *queue;
 	struct tun_file *tfile;
 	int len = skb->len;
 
@@ -1036,7 +1100,10 @@
 		goto drop;
 
 	len = run_ebpf_filter(tun, skb, len);
-	if (len == 0 || pskb_trim(skb, len))
+	if (len == 0)
+		goto drop;
+
+	if (pskb_trim(skb, len))
 		goto drop;
 
 	if (unlikely(skb_orphan_frags_rx(skb, GFP_ATOMIC)))
@@ -1054,6 +1121,10 @@
 	if (ptr_ring_produce(&tfile->tx_ring, skb))
 		goto drop;
 
+	/* NETIF_F_LLTX requires to do our own update of trans_start */
+	queue = netdev_get_tx_queue(dev, txq);
+	queue->trans_start = jiffies;
+
 	/* Notify and wake up reader process */
 	if (tfile->flags & TUN_FASYNC)
 		kill_fasync(&tfile->fasync, SIGIO, POLL_IN);
@@ -1164,6 +1235,7 @@
 }
 
 static const struct net_device_ops tun_netdev_ops = {
+	.ndo_init		= tun_net_init,
 	.ndo_uninit		= tun_net_uninit,
 	.ndo_open		= tun_net_open,
 	.ndo_stop		= tun_net_close,
@@ -1247,6 +1319,7 @@
 }
 
 static const struct net_device_ops tap_netdev_ops = {
+	.ndo_init		= tun_net_init,
 	.ndo_uninit		= tun_net_uninit,
 	.ndo_open		= tun_net_open,
 	.ndo_stop		= tun_net_close,
@@ -1287,7 +1360,7 @@
 #define MAX_MTU 65535
 
 /* Initialize net device. */
-static void tun_net_init(struct net_device *dev)
+static void tun_net_initialize(struct net_device *dev)
 {
 	struct tun_struct *tun = netdev_priv(dev);
 
@@ -1375,7 +1448,8 @@
 	int err;
 	int i;
 
-	if (it->nr_segs > MAX_SKB_FRAGS + 1)
+	if (it->nr_segs > MAX_SKB_FRAGS + 1 ||
+	    len > (ETH_MAX_MTU - NET_SKB_PAD - NET_IP_ALIGN))
 		return ERR_PTR(-EMSGSIZE);
 
 	local_bh_disable();
@@ -1501,7 +1575,7 @@
 	if (zerocopy)
 		return false;
 
-	if (SKB_DATA_ALIGN(len + TUN_RX_PAD) +
+	if (SKB_DATA_ALIGN(len + TUN_RX_PAD + XDP_PACKET_HEADROOM) +
 	    SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) > PAGE_SIZE)
 		return false;
 
@@ -1878,17 +1952,25 @@
 					  skb_headlen(skb));
 
 		if (unlikely(headlen > skb_headlen(skb))) {
+			WARN_ON_ONCE(1);
+			err = -ENOMEM;
 			atomic_long_inc(&tun->dev->rx_dropped);
+napi_busy:
 			napi_free_frags(&tfile->napi);
 			rcu_read_unlock();
 			mutex_unlock(&tfile->napi_mutex);
-			WARN_ON(1);
-			return -ENOMEM;
+			return err;
 		}
 
-		local_bh_disable();
-		napi_gro_frags(&tfile->napi);
-		local_bh_enable();
+		if (likely(napi_schedule_prep(&tfile->napi))) {
+			local_bh_disable();
+			napi_gro_frags(&tfile->napi);
+			napi_complete(&tfile->napi);
+			local_bh_enable();
+		} else {
+			err = -EBUSY;
+			goto napi_busy;
+		}
 		mutex_unlock(&tfile->napi_mutex);
 	} else if (tfile->napi_enabled) {
 		struct sk_buff_head *queue = &tfile->sk.sk_write_queue;
@@ -2014,14 +2096,16 @@
 					    tun_is_little_endian(tun), true,
 					    vlan_hlen)) {
 			struct skb_shared_info *sinfo = skb_shinfo(skb);
-			pr_err("unexpected GSO type: "
-			       "0x%x, gso_size %d, hdr_len %d\n",
-			       sinfo->gso_type, tun16_to_cpu(tun, gso.gso_size),
-			       tun16_to_cpu(tun, gso.hdr_len));
-			print_hex_dump(KERN_ERR, "tun: ",
-				       DUMP_PREFIX_NONE,
-				       16, 1, skb->head,
-				       min((int)tun16_to_cpu(tun, gso.hdr_len), 64), true);
+
+			if (net_ratelimit()) {
+				netdev_err(tun->dev, "unexpected GSO type: 0x%x, gso_size %d, hdr_len %d\n",
+					   sinfo->gso_type, tun16_to_cpu(tun, gso.gso_size),
+					   tun16_to_cpu(tun, gso.hdr_len));
+				print_hex_dump(KERN_ERR, "tun: ",
+					       DUMP_PREFIX_NONE,
+					       16, 1, skb->head,
+					       min((int)tun16_to_cpu(tun, gso.hdr_len), 64), true);
+			}
 			WARN_ON_ONCE(1);
 			return -EINVAL;
 		}
@@ -2201,11 +2285,6 @@
 	BUG_ON(!(list_empty(&tun->disabled)));
 
 	free_percpu(dev->tstats);
-	/* We clear tstats so that tun_set_iff() can tell if
-	 * tun_free_netdev() has been called from register_netdevice().
-	 */
-	dev->tstats = NULL;
-
 	tun_flow_uninit(tun);
 	security_tun_dev_free_security(tun->security);
 	__tun_set_ebpf(tun, &tun->steering_prog, NULL);
@@ -2343,6 +2422,9 @@
 	bool skb_xdp = false;
 	struct page *page;
 
+	if (unlikely(datasize < ETH_HLEN))
+		return -EINVAL;
+
 	xdp_prog = rcu_dereference(tun->xdp_prog);
 	if (xdp_prog) {
 		if (gso->gso_type) {
@@ -2438,7 +2520,8 @@
 	if (!tun)
 		return -EBADFD;
 
-	if (ctl && (ctl->type == TUN_MSG_PTR)) {
+	if (m->msg_controllen == sizeof(struct tun_msg_ctl) &&
+	    ctl && ctl->type == TUN_MSG_PTR) {
 		struct tun_page tpage;
 		int n = ctl->num;
 		int flush = 0;
@@ -2711,41 +2794,16 @@
 		tun->rx_batched = 0;
 		RCU_INIT_POINTER(tun->steering_prog, NULL);
 
-		dev->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
-		if (!dev->tstats) {
-			err = -ENOMEM;
-			goto err_free_dev;
-		}
-
-		spin_lock_init(&tun->lock);
-
-		err = security_tun_dev_alloc_security(&tun->security);
-		if (err < 0)
-			goto err_free_stat;
-
-		tun_net_init(dev);
-		tun_flow_init(tun);
+		tun->ifr = ifr;
+		tun->file = file;
 
-		dev->hw_features = NETIF_F_SG | NETIF_F_FRAGLIST |
-				   TUN_USER_FEATURES | NETIF_F_HW_VLAN_CTAG_TX |
-				   NETIF_F_HW_VLAN_STAG_TX;
-		dev->features = dev->hw_features | NETIF_F_LLTX;
-		dev->vlan_features = dev->features &
-				     ~(NETIF_F_HW_VLAN_CTAG_TX |
-				       NETIF_F_HW_VLAN_STAG_TX);
-
-		tun->flags = (tun->flags & ~TUN_FEATURES) |
-			      (ifr->ifr_flags & TUN_FEATURES);
-
-		INIT_LIST_HEAD(&tun->disabled);
-		err = tun_attach(tun, file, false, ifr->ifr_flags & IFF_NAPI,
-				 ifr->ifr_flags & IFF_NAPI_FRAGS, false);
-		if (err < 0)
-			goto err_free_flow;
+		tun_net_initialize(dev);
 
 		err = register_netdevice(tun->dev);
-		if (err < 0)
-			goto err_detach;
+		if (err < 0) {
+			free_netdev(dev);
+			return err;
+		}
 		/* free_netdev() won't check refcnt, to avoid race
 		 * with dev_put() we need publish tun after registration.
 		 */
@@ -2762,24 +2820,6 @@
 
 	strcpy(ifr->ifr_name, tun->dev->name);
 	return 0;
-
-err_detach:
-	tun_detach_all(dev);
-	/* We are here because register_netdevice() has failed.
-	 * If register_netdevice() already called tun_free_netdev()
-	 * while dealing with the error, dev->stats has been cleared.
-	 */
-	if (!dev->tstats)
-		goto err_free_dev;
-
-err_free_flow:
-	tun_flow_uninit(tun);
-	security_tun_dev_free_security(tun->security);
-err_free_stat:
-	free_percpu(dev->tstats);
-err_free_dev:
-	free_netdev(dev);
-	return err;
 }
 
 static void tun_get_iff(struct tun_struct *tun, struct ifreq *ifr)
@@ -2976,10 +3016,11 @@
 	struct net *net = sock_net(&tfile->sk);
 	struct tun_struct *tun;
 	void __user* argp = (void __user*)arg;
-	unsigned int ifindex, carrier;
+	unsigned int carrier;
 	struct ifreq ifr;
 	kuid_t owner;
 	kgid_t group;
+	int ifindex;
 	int sndbuf;
 	int vnet_hdr_sz;
 	int le;
@@ -3035,7 +3076,9 @@
 		ret = -EFAULT;
 		if (copy_from_user(&ifindex, argp, sizeof(ifindex)))
 			goto unlock;
-
+		ret = -EINVAL;
+		if (ifindex < 0)
+			goto unlock;
 		ret = 0;
 		tfile->ifindex = ifindex;
 		goto unlock;
@@ -3377,7 +3420,7 @@
 	tfile->socket.file = file;
 	tfile->socket.ops = &tun_socket_ops;
 
-	sock_init_data(&tfile->socket, &tfile->sk);
+	sock_init_data_uid(&tfile->socket, &tfile->sk, current_fsuid());
 
 	tfile->sk.sk_write_space = tun_sock_write_space;
 	tfile->sk.sk_sndbuf = INT_MAX;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/Kconfig
@@ -636,8 +636,9 @@
 	  * Aquantia AQtion USB to 5GbE
 
 config USB_RTL8153_ECM
-	tristate "RTL8153 ECM support"
+	tristate
 	depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
+	default y
 	help
 	  This option supports ECM mode for RTL8153 ethernet adapter, when
 	  CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/aqc111.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/aqc111.c
@@ -119,7 +119,7 @@
 }
 
 static int aqc111_write_cmd(struct usbnet *dev, u8 cmd, u16 value,
-			    u16 index, u16 size, void *data)
+			    u16 index, u16 size, const void *data)
 {
 	int ret;
 
@@ -1079,17 +1079,17 @@
 	u16 pkt_count = 0;
 	u64 desc_hdr = 0;
 	u16 vlan_tag = 0;
-	u32 skb_len = 0;
+	u32 skb_len;
 
 	if (!skb)
 		goto err;
 
-	if (skb->len == 0)
+	skb_len = skb->len;
+	if (skb_len < sizeof(desc_hdr))
 		goto err;
 
-	skb_len = skb->len;
 	/* RX Descriptor Header */
-	skb_trim(skb, skb->len - sizeof(desc_hdr));
+	skb_trim(skb, skb_len - sizeof(desc_hdr));
 	desc_hdr = le64_to_cpup((u64 *)skb_tail_pointer(skb));
 
 	/* Check these packets */
@@ -1102,10 +1102,15 @@
 	if (start_of_descs != desc_offset)
 		goto err;
 
-	/* self check desc_offset from header*/
-	if (desc_offset >= skb_len)
+	/* self check desc_offset from header and make sure that the
+	 * bounds of the metadata array are inside the SKB
+	 */
+	if (pkt_count * 2 + desc_offset >= skb_len)
 		goto err;
 
+	/* Packets must not overlap the metadata array */
+	skb_trim(skb, desc_offset);
+
 	if (pkt_count == 0)
 		goto err;
 
@@ -1136,17 +1141,15 @@
 			continue;
 		}
 
-		/* Clone SKB */
-		new_skb = skb_clone(skb, GFP_ATOMIC);
+		new_skb = netdev_alloc_skb_ip_align(dev->net, pkt_len);
 
 		if (!new_skb)
 			goto err;
 
-		new_skb->len = pkt_len;
+		skb_put(new_skb, pkt_len);
+		memcpy(new_skb->data, skb->data, pkt_len);
 		skb_pull(new_skb, AQ_RX_HW_PAD);
-		skb_set_tail_pointer(new_skb, new_skb->len);
 
-		new_skb->truesize = SKB_TRUESIZE(new_skb->len);
 		if (aqc111_data->rx_checksum)
 			aqc111_rx_checksum(new_skb, pkt_desc);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/asix.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/asix.h
@@ -126,8 +126,7 @@
 	 AX_MEDIUM_RE)
 
 #define AX88772_MEDIUM_DEFAULT	\
-	(AX_MEDIUM_FD | AX_MEDIUM_RFC | \
-	 AX_MEDIUM_TFC | AX_MEDIUM_PS | \
+	(AX_MEDIUM_FD | AX_MEDIUM_PS | \
 	 AX_MEDIUM_AC | AX_MEDIUM_RE)
 
 /* AX88772 & AX88178 RX_CTL values */
@@ -158,6 +157,8 @@
 #define AX_EEPROM_MAGIC		0xdeadbeef
 #define AX_EEPROM_LEN		0x200
 
+#define AX_EMBD_PHY_ADDR	0x10
+
 /* This structure cannot exceed sizeof(unsigned long [5]) AKA 20 bytes */
 struct asix_data {
 	u8 multi_filter[AX_MCAST_FILTER_SIZE];
@@ -182,6 +183,7 @@
 	struct asix_rx_fixup_info rx_fixup_info;
 	struct mii_bus *mdio;
 	struct phy_device *phydev;
+	struct phy_device *phydev_int;
 	u16 phy_addr;
 	char phy_name[20];
 	bool embd_phy;
@@ -192,8 +194,8 @@
 /* ASIX specific flags */
 #define FLAG_EEPROM_MAC		(1UL << 0)  /* init device MAC from eeprom */
 
-int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data, int in_pm);
+int __must_check asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
+			       u16 size, void *data, int in_pm);
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
 		   u16 size, void *data, int in_pm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/asix_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/asix_common.c
@@ -9,8 +9,10 @@
 
 #include "asix.h"
 
-int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data, int in_pm)
+#define AX_HOST_EN_RETRIES	30
+
+int __must_check asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
+			       u16 size, void *data, int in_pm)
 {
 	int ret;
 	int (*fn)(struct usbnet *, u8, u8, u16, u16, void *, u16);
@@ -25,9 +27,12 @@
 	ret = fn(dev, cmd, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 value, index, data, size);
 
-	if (unlikely(ret < 0))
+	if (unlikely(ret < size)) {
+		ret = ret < 0 ? ret : -ENODATA;
+
 		netdev_warn(dev->net, "Failed to read reg index 0x%04x: %d\n",
 			    index, ret);
+	}
 
 	return ret;
 }
@@ -68,7 +73,7 @@
 	int i, ret;
 	u8 smsr;
 
-	for (i = 0; i < 30; ++i) {
+	for (i = 0; i < AX_HOST_EN_RETRIES; ++i) {
 		ret = asix_set_sw_mii(dev, in_pm);
 		if (ret == -ENODEV || ret == -ETIMEDOUT)
 			break;
@@ -83,7 +88,7 @@
 			break;
 	}
 
-	return ret;
+	return i >= AX_HOST_EN_RETRIES ? -ETIMEDOUT : ret;
 }
 
 static void reset_asix_rx_fixup_info(struct asix_rx_fixup_info *rx)
@@ -426,6 +431,7 @@
 
 	asix_write_medium_mode(dev, mode, 0);
 	phy_print_status(phydev);
+	usbnet_link_change(dev, phydev->link, 0);
 }
 
 int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
@@ -577,8 +583,12 @@
 		return ret;
 	}
 
-	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
-		      (__u16)loc, 2, &res, 1);
+	ret = asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
+			    (__u16)loc, 2, &res, 1);
+	if (ret < 0) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
 	asix_set_hw_mii(dev, 1);
 	mutex_unlock(&dev->phy_mutex);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/asix_devices.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/asix_devices.c
@@ -694,10 +694,26 @@
 	}
 
 	phy_suspend(priv->phydev);
-	priv->phydev->mac_managed_pm = 1;
+	priv->phydev->mac_managed_pm = true;
 
 	phy_attached_info(priv->phydev);
 
+	if (priv->embd_phy)
+		return 0;
+
+	/* In case main PHY is not the embedded PHY and MAC is RMII clock
+	 * provider, we need to suspend embedded PHY by keeping PLL enabled
+	 * (AX_SWRESET_IPPD == 0).
+	 */
+	priv->phydev_int = mdiobus_get_phy(priv->mdio, AX_EMBD_PHY_ADDR);
+	if (!priv->phydev_int) {
+		netdev_err(dev->net, "Could not find internal PHY\n");
+		return -ENODEV;
+	}
+
+	priv->phydev_int->mac_managed_pm = true;
+	phy_suspend(priv->phydev_int);
+
 	return 0;
 }
 
@@ -753,9 +769,14 @@
 		return ret;
 
 	priv->phy_addr = ret;
-	priv->embd_phy = ((priv->phy_addr & 0x1f) == 0x10);
+	priv->embd_phy = ((priv->phy_addr & 0x1f) == AX_EMBD_PHY_ADDR);
+
+	ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Failed to read STATMNGSTS_REG: %d\n", ret);
+		return ret;
+	}
 
-	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
 	chipcode &= AX_CHIPCODE_MASK;
 
 	ret = (chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
@@ -794,11 +815,7 @@
 {
 	struct asix_common_private *priv = dev->driver_priv;
 
-	/* On unplugged USB, we will get MDIO communication errors and the
-	 * PHY will be set in to PHY_HALTED state.
-	 */
-	if (priv->phydev->state != PHY_HALTED)
-		phy_stop(priv->phydev);
+	phy_stop(priv->phydev);
 
 	return 0;
 }
@@ -920,11 +937,21 @@
 	int gpio0 = 0;
 	u32 phyid;
 
-	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0);
+	ret = asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Failed to read GPIOS: %d\n", ret);
+		return ret;
+	}
+
 	netdev_dbg(dev->net, "GPIO Status: 0x%04x\n", status);
 
 	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL, 0);
-	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0);
+	ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Failed to read EEPROM: %d\n", ret);
+		return ret;
+	}
+
 	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL, 0);
 
 	netdev_dbg(dev->net, "EEPROM index 0x17 is 0x%04x\n", eeprom);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/ax88172a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/ax88172a.c
@@ -161,7 +161,9 @@
 	u8 buf[ETH_ALEN];
 	struct ax88172a_private *priv;
 
-	usbnet_get_endpoints(dev, intf);
+	ret = usbnet_get_endpoints(dev, intf);
+	if (ret)
+		return ret;
 
 	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
 	if (!priv)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/ax88179_178a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/ax88179_178a.c
@@ -164,11 +164,16 @@
 	#define GMII_PHY_PGSEL_PAGE3	0x0003
 	#define GMII_PHY_PGSEL_PAGE5	0x0005
 
+static int ax88179_reset(struct usbnet *dev);
+
 struct ax88179_data {
 	u8  eee_enabled;
 	u8  eee_active;
 	u16 rxctl;
-	u16 reserved;
+	u8 in_pm;
+	u32 wol_supported;
+	u32 wolopts;
+	u8 disconnecting;
 };
 
 struct ax88179_int_data {
@@ -185,15 +190,30 @@
 	{7, 0xcc, 0x4c, 0x18, 8},
 };
 
+static void ax88179_set_pm_mode(struct usbnet *dev, bool pm_mode)
+{
+	struct ax88179_data *ax179_data = dev->driver_priv;
+
+	ax179_data->in_pm = pm_mode;
+}
+
+static int ax88179_in_pm(struct usbnet *dev)
+{
+	struct ax88179_data *ax179_data = dev->driver_priv;
+
+	return ax179_data->in_pm;
+}
+
 static int __ax88179_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-			      u16 size, void *data, int in_pm)
+			      u16 size, void *data)
 {
 	int ret;
 	int (*fn)(struct usbnet *, u8, u8, u16, u16, void *, u16);
+	struct ax88179_data *ax179_data = dev->driver_priv;
 
 	BUG_ON(!dev);
 
-	if (!in_pm)
+	if (!ax88179_in_pm(dev))
 		fn = usbnet_read_cmd;
 	else
 		fn = usbnet_read_cmd_nopm;
@@ -201,7 +221,7 @@
 	ret = fn(dev, cmd, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 value, index, data, size);
 
-	if (unlikely(ret < 0))
+	if (unlikely((ret < 0) && !(ret == -ENODEV && ax179_data->disconnecting)))
 		netdev_warn(dev->net, "Failed to read reg index 0x%04x: %d\n",
 			    index, ret);
 
@@ -209,14 +229,15 @@
 }
 
 static int __ax88179_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-			       u16 size, void *data, int in_pm)
+			       u16 size, const void *data)
 {
 	int ret;
 	int (*fn)(struct usbnet *, u8, u8, u16, u16, const void *, u16);
+	struct ax88179_data *ax179_data = dev->driver_priv;
 
 	BUG_ON(!dev);
 
-	if (!in_pm)
+	if (!ax88179_in_pm(dev))
 		fn = usbnet_write_cmd;
 	else
 		fn = usbnet_write_cmd_nopm;
@@ -224,7 +245,7 @@
 	ret = fn(dev, cmd, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 value, index, data, size);
 
-	if (unlikely(ret < 0))
+	if (unlikely((ret < 0) && !(ret == -ENODEV && ax179_data->disconnecting)))
 		netdev_warn(dev->net, "Failed to write reg index 0x%04x: %d\n",
 			    index, ret);
 
@@ -249,47 +270,6 @@
 	}
 }
 
-static int ax88179_read_cmd_nopm(struct usbnet *dev, u8 cmd, u16 value,
-				 u16 index, u16 size, void *data)
-{
-	int ret;
-
-	if (2 == size) {
-		u16 buf;
-		ret = __ax88179_read_cmd(dev, cmd, value, index, size, &buf, 1);
-		le16_to_cpus(&buf);
-		*((u16 *)data) = buf;
-	} else if (4 == size) {
-		u32 buf;
-		ret = __ax88179_read_cmd(dev, cmd, value, index, size, &buf, 1);
-		le32_to_cpus(&buf);
-		*((u32 *)data) = buf;
-	} else {
-		ret = __ax88179_read_cmd(dev, cmd, value, index, size, data, 1);
-	}
-
-	return ret;
-}
-
-static int ax88179_write_cmd_nopm(struct usbnet *dev, u8 cmd, u16 value,
-				  u16 index, u16 size, void *data)
-{
-	int ret;
-
-	if (2 == size) {
-		u16 buf;
-		buf = *((u16 *)data);
-		cpu_to_le16s(&buf);
-		ret = __ax88179_write_cmd(dev, cmd, value, index,
-					  size, &buf, 1);
-	} else {
-		ret = __ax88179_write_cmd(dev, cmd, value, index,
-					  size, data, 1);
-	}
-
-	return ret;
-}
-
 static int ax88179_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
 			    u16 size, void *data)
 {
@@ -297,23 +277,23 @@
 
 	if (2 == size) {
 		u16 buf = 0;
-		ret = __ax88179_read_cmd(dev, cmd, value, index, size, &buf, 0);
+		ret = __ax88179_read_cmd(dev, cmd, value, index, size, &buf);
 		le16_to_cpus(&buf);
 		*((u16 *)data) = buf;
 	} else if (4 == size) {
 		u32 buf = 0;
-		ret = __ax88179_read_cmd(dev, cmd, value, index, size, &buf, 0);
+		ret = __ax88179_read_cmd(dev, cmd, value, index, size, &buf);
 		le32_to_cpus(&buf);
 		*((u32 *)data) = buf;
 	} else {
-		ret = __ax88179_read_cmd(dev, cmd, value, index, size, data, 0);
+		ret = __ax88179_read_cmd(dev, cmd, value, index, size, data);
 	}
 
 	return ret;
 }
 
 static int ax88179_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-			     u16 size, void *data)
+			     u16 size, const void *data)
 {
 	int ret;
 
@@ -322,10 +302,10 @@
 		buf = *((u16 *)data);
 		cpu_to_le16s(&buf);
 		ret = __ax88179_write_cmd(dev, cmd, value, index,
-					  size, &buf, 0);
+					  size, &buf);
 	} else {
 		ret = __ax88179_write_cmd(dev, cmd, value, index,
-					  size, data, 0);
+					  size, data);
 	}
 
 	return ret;
@@ -346,7 +326,8 @@
 
 	if (netif_carrier_ok(dev->net) != link) {
 		usbnet_link_change(dev, link, 1);
-		netdev_info(dev->net, "ax88179 - Link status is: %d\n", link);
+		if (!link)
+			netdev_info(dev->net, "ax88179 - Link status is: 0\n");
 	}
 }
 
@@ -425,55 +406,63 @@
 static int ax88179_suspend(struct usb_interface *intf, pm_message_t message)
 {
 	struct usbnet *dev = usb_get_intfdata(intf);
+	struct ax88179_data *priv = dev->driver_priv;
 	u16 tmp16;
 	u8 tmp8;
 
+	ax88179_set_pm_mode(dev, true);
+
 	usbnet_suspend(intf, message);
 
+	/* Enable WoL */
+	if (priv->wolopts) {
+		ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD,
+				 1, 1, &tmp8);
+		if (priv->wolopts & WAKE_PHY)
+			tmp8 |= AX_MONITOR_MODE_RWLC;
+		if (priv->wolopts & WAKE_MAGIC)
+			tmp8 |= AX_MONITOR_MODE_RWMP;
+
+		ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD,
+				  1, 1, &tmp8);
+	}
+
 	/* Disable RX path */
-	ax88179_read_cmd_nopm(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
-			      2, 2, &tmp16);
+	ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
+			 2, 2, &tmp16);
 	tmp16 &= ~AX_MEDIUM_RECEIVE_EN;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
-			       2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
+			  2, 2, &tmp16);
 
 	/* Force bulk-in zero length */
-	ax88179_read_cmd_nopm(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
-			      2, 2, &tmp16);
+	ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
+			 2, 2, &tmp16);
 
 	tmp16 |= AX_PHYPWR_RSTCTL_BZ | AX_PHYPWR_RSTCTL_IPRL;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
-			       2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
+			  2, 2, &tmp16);
 
 	/* change clock */
 	tmp8 = 0;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
 
 	/* Configure RX control register => stop operation */
 	tmp16 = AX_RX_CTL_STOP;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, &tmp16);
+
+	ax88179_set_pm_mode(dev, false);
 
 	return 0;
 }
 
 /* This function is used to enable the autodetach function. */
 /* This function is determined by offset 0x43 of EEPROM */
-static int ax88179_auto_detach(struct usbnet *dev, int in_pm)
+static int ax88179_auto_detach(struct usbnet *dev)
 {
 	u16 tmp16;
 	u8 tmp8;
-	int (*fnr)(struct usbnet *, u8, u16, u16, u16, void *);
-	int (*fnw)(struct usbnet *, u8, u16, u16, u16, void *);
 
-	if (!in_pm) {
-		fnr = ax88179_read_cmd;
-		fnw = ax88179_write_cmd;
-	} else {
-		fnr = ax88179_read_cmd_nopm;
-		fnw = ax88179_write_cmd_nopm;
-	}
-
-	if (fnr(dev, AX_ACCESS_EEPROM, 0x43, 1, 2, &tmp16) < 0)
+	if (ax88179_read_cmd(dev, AX_ACCESS_EEPROM, 0x43, 1, 2, &tmp16) < 0)
 		return 0;
 
 	if ((tmp16 == 0xFFFF) || (!(tmp16 & 0x0100)))
@@ -481,13 +470,13 @@
 
 	/* Enable Auto Detach bit */
 	tmp8 = 0;
-	fnr(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
+	ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
 	tmp8 |= AX_CLK_SELECT_ULR;
-	fnw(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
 
-	fnr(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, &tmp16);
+	ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, &tmp16);
 	tmp16 |= AX_PHYPWR_RSTCTL_AT;
-	fnw(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, &tmp16);
 
 	return 0;
 }
@@ -498,74 +487,74 @@
 	u16 tmp16;
 	u8 tmp8;
 
+	ax88179_set_pm_mode(dev, true);
+
 	usbnet_link_change(dev, 0, 0);
 
 	/* Power up ethernet PHY */
 	tmp16 = 0;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
-			       2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
+			  2, 2, &tmp16);
 	udelay(1000);
 
 	tmp16 = AX_PHYPWR_RSTCTL_IPRL;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
-			       2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL,
+			  2, 2, &tmp16);
 	msleep(200);
 
 	/* Ethernet PHY Auto Detach*/
-	ax88179_auto_detach(dev, 1);
+	ax88179_auto_detach(dev);
 
 	/* Enable clock */
-	ax88179_read_cmd_nopm(dev, AX_ACCESS_MAC,  AX_CLK_SELECT, 1, 1, &tmp8);
+	ax88179_read_cmd(dev, AX_ACCESS_MAC,  AX_CLK_SELECT, 1, 1, &tmp8);
 	tmp8 |= AX_CLK_SELECT_ACS | AX_CLK_SELECT_BCS;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, &tmp8);
 	msleep(100);
 
 	/* Configure RX control register => start operation */
 	tmp16 = AX_RX_CTL_DROPCRCERR | AX_RX_CTL_IPE | AX_RX_CTL_START |
 		AX_RX_CTL_AP | AX_RX_CTL_AMALL | AX_RX_CTL_AB;
-	ax88179_write_cmd_nopm(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, &tmp16);
+	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, &tmp16);
+
+	ax88179_set_pm_mode(dev, false);
 
 	return usbnet_resume(intf);
 }
 
+static void ax88179_disconnect(struct usb_interface *intf)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct ax88179_data *ax179_data;
+
+	if (!dev)
+		return;
+
+	ax179_data = dev->driver_priv;
+	ax179_data->disconnecting = 1;
+
+	usbnet_disconnect(intf);
+}
+
 static void
 ax88179_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 {
 	struct usbnet *dev = netdev_priv(net);
-	u8 opt;
+	struct ax88179_data *priv = dev->driver_priv;
 
-	if (ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD,
-			     1, 1, &opt) < 0) {
-		wolinfo->supported = 0;
-		wolinfo->wolopts = 0;
-		return;
-	}
-
-	wolinfo->supported = WAKE_PHY | WAKE_MAGIC;
-	wolinfo->wolopts = 0;
-	if (opt & AX_MONITOR_MODE_RWLC)
-		wolinfo->wolopts |= WAKE_PHY;
-	if (opt & AX_MONITOR_MODE_RWMP)
-		wolinfo->wolopts |= WAKE_MAGIC;
+	wolinfo->supported = priv->wol_supported;
+	wolinfo->wolopts = priv->wolopts;
 }
 
 static int
 ax88179_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 {
 	struct usbnet *dev = netdev_priv(net);
-	u8 opt = 0;
+	struct ax88179_data *priv = dev->driver_priv;
 
-	if (wolinfo->wolopts & ~(WAKE_PHY | WAKE_MAGIC))
+	if (wolinfo->wolopts & ~(priv->wol_supported))
 		return -EINVAL;
 
-	if (wolinfo->wolopts & WAKE_PHY)
-		opt |= AX_MONITOR_MODE_RWLC;
-	if (wolinfo->wolopts & WAKE_MAGIC)
-		opt |= AX_MONITOR_MODE_RWMP;
-
-	if (ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD,
-			      1, 1, &opt) < 0)
-		return -EINVAL;
+	priv->wolopts = wolinfo->wolopts;
 
 	return 0;
 }
@@ -599,8 +588,7 @@
 	/* ax88179/178A returns 2 bytes from eeprom on read */
 	for (i = first_word; i <= last_word; i++) {
 		ret = __ax88179_read_cmd(dev, AX_ACCESS_EEPROM, i, 1, 2,
-					 &eeprom_buff[i - first_word],
-					 0);
+					 &eeprom_buff[i - first_word]);
 		if (ret < 0) {
 			kfree(eeprom_buff);
 			return -EIO;
@@ -745,7 +733,7 @@
 static int ax88179_chk_eee(struct usbnet *dev)
 {
 	struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET };
-	struct ax88179_data *priv = (struct ax88179_data *)dev->data;
+	struct ax88179_data *priv = dev->driver_priv;
 
 	mii_ethtool_gset(&dev->mii, &ecmd);
 
@@ -848,7 +836,7 @@
 static int ax88179_get_eee(struct net_device *net, struct ethtool_eee *edata)
 {
 	struct usbnet *dev = netdev_priv(net);
-	struct ax88179_data *priv = (struct ax88179_data *)dev->data;
+	struct ax88179_data *priv = dev->driver_priv;
 
 	edata->eee_enabled = priv->eee_enabled;
 	edata->eee_active = priv->eee_active;
@@ -859,7 +847,7 @@
 static int ax88179_set_eee(struct net_device *net, struct ethtool_eee *edata)
 {
 	struct usbnet *dev = netdev_priv(net);
-	struct ax88179_data *priv = (struct ax88179_data *)dev->data;
+	struct ax88179_data *priv = dev->driver_priv;
 	int ret;
 
 	priv->eee_enabled = edata->eee_enabled;
@@ -910,8 +898,8 @@
 static void ax88179_set_multicast(struct net_device *net)
 {
 	struct usbnet *dev = netdev_priv(net);
-	struct ax88179_data *data = (struct ax88179_data *)dev->data;
-	u8 *m_filter = ((u8 *)dev->data) + 12;
+	struct ax88179_data *data = dev->driver_priv;
+	u8 *m_filter = ((u8 *)dev->data);
 
 	data->rxctl = (AX_RX_CTL_START | AX_RX_CTL_AB | AX_RX_CTL_IPE);
 
@@ -923,7 +911,7 @@
 	} else if (netdev_mc_empty(net)) {
 		/* just broadcast and directed */
 	} else {
-		/* We use the 20 byte dev->data for our 8 byte filter buffer
+		/* We use dev->data for our 8 byte filter buffer
 		 * to avoid allocating memory that is tricky to free later
 		 */
 		u32 crc_bits;
@@ -1069,7 +1057,7 @@
 		} while (buf & EEP_BUSY);
 
 		__ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_SROM_DATA_LOW,
-				   2, 2, &eeprom[i * 2], 0);
+				   2, 2, &eeprom[i * 2]);
 
 		if ((i == 0) && (eeprom[0] == 0xFF))
 			return -EINVAL;
@@ -1322,46 +1310,15 @@
 
 static int ax88179_bind(struct usbnet *dev, struct usb_interface *intf)
 {
-	u8 buf[5];
-	u16 *tmp16;
-	u8 *tmp;
-	struct ax88179_data *ax179_data = (struct ax88179_data *)dev->data;
-	struct ethtool_eee eee_data;
+	struct ax88179_data *ax179_data;
 
 	usbnet_get_endpoints(dev, intf);
 
-	tmp16 = (u16 *)buf;
-	tmp = (u8 *)buf;
-
-	memset(ax179_data, 0, sizeof(*ax179_data));
-
-	/* Power up ethernet PHY */
-	*tmp16 = 0;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, tmp16);
-	*tmp16 = AX_PHYPWR_RSTCTL_IPRL;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, tmp16);
-	msleep(200);
-
-	*tmp = AX_CLK_SELECT_ACS | AX_CLK_SELECT_BCS;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, tmp);
-	msleep(100);
-
-	/* Read MAC address from DTB or asix chip */
-	ax88179_get_mac_addr(dev);
-	memcpy(dev->net->perm_addr, dev->net->dev_addr, ETH_ALEN);
-
-	/* RX bulk configuration */
-	memcpy(tmp, &AX88179_BULKIN_SIZE[0], 5);
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_BULKIN_QCTRL, 5, 5, tmp);
-
-	dev->rx_urb_size = 1024 * 20;
-
-	*tmp = 0x34;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PAUSE_WATERLVL_LOW, 1, 1, tmp);
+	ax179_data = kzalloc(sizeof(*ax179_data), GFP_KERNEL);
+	if (!ax179_data)
+		return -ENOMEM;
 
-	*tmp = 0x52;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PAUSE_WATERLVL_HIGH,
-			  1, 1, tmp);
+	dev->driver_priv = ax179_data;
 
 	dev->net->netdev_ops = &ax88179_netdev_ops;
 	dev->net->ethtool_ops = &ax88179_ethtool_ops;
@@ -1383,52 +1340,14 @@
 	dev->net->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
 				 NETIF_F_RXCSUM;
 
-	/* Enable checksum offload */
-	*tmp = AX_RXCOE_IP | AX_RXCOE_TCP | AX_RXCOE_UDP |
-	       AX_RXCOE_TCPV6 | AX_RXCOE_UDPV6;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RXCOE_CTL, 1, 1, tmp);
-
-	*tmp = AX_TXCOE_IP | AX_TXCOE_TCP | AX_TXCOE_UDP |
-	       AX_TXCOE_TCPV6 | AX_TXCOE_UDPV6;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_TXCOE_CTL, 1, 1, tmp);
-
-	/* Configure RX control register => start operation */
-	*tmp16 = AX_RX_CTL_DROPCRCERR | AX_RX_CTL_IPE | AX_RX_CTL_START |
-		 AX_RX_CTL_AP | AX_RX_CTL_AMALL | AX_RX_CTL_AB;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, tmp16);
-
-	*tmp = AX_MONITOR_MODE_PMETYPE | AX_MONITOR_MODE_PMEPOL |
-	       AX_MONITOR_MODE_RWMP;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD, 1, 1, tmp);
-
-	/* Configure default medium type => giga */
-	*tmp16 = AX_MEDIUM_RECEIVE_EN | AX_MEDIUM_TXFLOW_CTRLEN |
-		 AX_MEDIUM_RXFLOW_CTRLEN | AX_MEDIUM_FULL_DUPLEX |
-		 AX_MEDIUM_GIGAMODE;
-	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
-			  2, 2, tmp16);
-
-	ax88179_led_setting(dev);
-
-	ax179_data->eee_enabled = 0;
-	ax179_data->eee_active = 0;
-
-	ax88179_disable_eee(dev);
-
-	ax88179_ethtool_get_eee(dev, &eee_data);
-	eee_data.advertised = 0;
-	ax88179_ethtool_set_eee(dev, &eee_data);
-
-	/* Restart autoneg */
-	mii_nway_restart(&dev->mii);
-
-	usbnet_link_change(dev, 0, 0);
+	ax88179_reset(dev);
 
 	return 0;
 }
 
 static void ax88179_unbind(struct usbnet *dev, struct usb_interface *intf)
 {
+	struct ax88179_data *ax179_data = dev->driver_priv;
 	u16 tmp16;
 
 	/* Configure RX control register => stop operation */
@@ -1441,6 +1360,8 @@
 	/* Power down ethernet PHY */
 	tmp16 = 0;
 	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, &tmp16);
+
+	kfree(ax179_data);
 }
 
 static void
@@ -1467,58 +1388,114 @@
 	u16 hdr_off;
 	u32 *pkt_hdr;
 
-	/* This check is no longer done by usbnet */
-	if (skb->len < dev->net->hard_header_len)
-		return 0;
+	/* At the end of the SKB, there's a header telling us how many packets
+	 * are bundled into this buffer and where we can find an array of
+	 * per-packet metadata (which contains elements encoded into u16).
+	 */
+
+	/* SKB contents for current firmware:
+	 *   <packet 1> <padding>
+	 *   ...
+	 *   <packet N> <padding>
+	 *   <per-packet metadata entry 1> <dummy header>
+	 *   ...
+	 *   <per-packet metadata entry N> <dummy header>
+	 *   <padding2> <rx_hdr>
+	 *
+	 * where:
+	 *   <packet N> contains pkt_len bytes:
+	 *		2 bytes of IP alignment pseudo header
+	 *		packet received
+	 *   <per-packet metadata entry N> contains 4 bytes:
+	 *		pkt_len and fields AX_RXHDR_*
+	 *   <padding>	0-7 bytes to terminate at
+	 *		8 bytes boundary (64-bit).
+	 *   <padding2> 4 bytes to make rx_hdr terminate at
+	 *		8 bytes boundary (64-bit)
+	 *   <dummy-header> contains 4 bytes:
+	 *		pkt_len=0 and AX_RXHDR_DROP_ERR
+	 *   <rx-hdr>	contains 4 bytes:
+	 *		pkt_cnt and hdr_off (offset of
+	 *		  <per-packet metadata entry 1>)
+	 *
+	 * pkt_cnt is number of entrys in the per-packet metadata.
+	 * In current firmware there is 2 entrys per packet.
+	 * The first points to the packet and the
+	 *  second is a dummy header.
+	 * This was done probably to align fields in 64-bit and
+	 *  maintain compatibility with old firmware.
+	 * This code assumes that <dummy header> and <padding2> are
+	 *  optional.
+	 */
 
+	if (skb->len < 4)
+		return 0;
 	skb_trim(skb, skb->len - 4);
 	rx_hdr = get_unaligned_le32(skb_tail_pointer(skb));
-
 	pkt_cnt = (u16)rx_hdr;
 	hdr_off = (u16)(rx_hdr >> 16);
+
+	if (pkt_cnt == 0)
+		return 0;
+
+	/* Make sure that the bounds of the metadata array are inside the SKB
+	 * (and in front of the counter at the end).
+	 */
+	if (pkt_cnt * 4 + hdr_off > skb->len)
+		return 0;
 	pkt_hdr = (u32 *)(skb->data + hdr_off);
 
-	while (pkt_cnt--) {
+	/* Packets must not overlap the metadata array */
+	skb_trim(skb, hdr_off);
+
+	for (; pkt_cnt > 0; pkt_cnt--, pkt_hdr++) {
+		u16 pkt_len_plus_padd;
 		u16 pkt_len;
 
 		le32_to_cpus(pkt_hdr);
 		pkt_len = (*pkt_hdr >> 16) & 0x1fff;
+		pkt_len_plus_padd = (pkt_len + 7) & 0xfff8;
+
+		/* Skip dummy header used for alignment
+		 */
+		if (pkt_len == 0)
+			continue;
+
+		if (pkt_len_plus_padd > skb->len)
+			return 0;
 
 		/* Check CRC or runt packet */
-		if ((*pkt_hdr & AX_RXHDR_CRC_ERR) ||
-		    (*pkt_hdr & AX_RXHDR_DROP_ERR)) {
-			skb_pull(skb, (pkt_len + 7) & 0xFFF8);
-			pkt_hdr++;
+		if ((*pkt_hdr & (AX_RXHDR_CRC_ERR | AX_RXHDR_DROP_ERR)) ||
+		    pkt_len < 2 + ETH_HLEN) {
+			dev->net->stats.rx_errors++;
+			skb_pull(skb, pkt_len_plus_padd);
 			continue;
 		}
 
-		if (pkt_cnt == 0) {
-			skb->len = pkt_len;
+		/* last packet */
+		if (pkt_len_plus_padd == skb->len) {
+			skb_trim(skb, pkt_len);
+
 			/* Skip IP alignment pseudo header */
 			skb_pull(skb, 2);
-			skb_set_tail_pointer(skb, skb->len);
-			skb->truesize = pkt_len + sizeof(struct sk_buff);
+
 			ax88179_rx_checksum(skb, pkt_hdr);
 			return 1;
 		}
 
-		ax_skb = skb_clone(skb, GFP_ATOMIC);
-		if (ax_skb) {
-			ax_skb->len = pkt_len;
-			/* Skip IP alignment pseudo header */
-			skb_pull(ax_skb, 2);
-			skb_set_tail_pointer(ax_skb, ax_skb->len);
-			ax_skb->truesize = pkt_len + sizeof(struct sk_buff);
-			ax88179_rx_checksum(ax_skb, pkt_hdr);
-			usbnet_skb_return(dev, ax_skb);
-		} else {
+		ax_skb = netdev_alloc_skb_ip_align(dev->net, pkt_len);
+		if (!ax_skb)
 			return 0;
-		}
+		skb_put(ax_skb, pkt_len);
+		memcpy(ax_skb->data, skb->data + 2, pkt_len);
+
+		ax88179_rx_checksum(ax_skb, pkt_hdr);
+		usbnet_skb_return(dev, ax_skb);
 
-		skb_pull(skb, (pkt_len + 7) & 0xFFF8);
-		pkt_hdr++;
+		skb_pull(skb, pkt_len_plus_padd);
 	}
-	return 1;
+
+	return 0;
 }
 
 static struct sk_buff *
@@ -1552,7 +1529,7 @@
 
 static int ax88179_link_reset(struct usbnet *dev)
 {
-	struct ax88179_data *ax179_data = (struct ax88179_data *)dev->data;
+	struct ax88179_data *ax179_data = dev->driver_priv;
 	u8 tmp[5], link_sts;
 	u16 mode, tmp16, delay = HZ / 10;
 	u32 tmp32 = 0x40000000;
@@ -1582,6 +1559,7 @@
 			 GMII_PHY_PHYSR, 2, &tmp16);
 
 	if (!(tmp16 & GMII_PHY_PHYSR_LINK)) {
+		netdev_info(dev->net, "ax88179 - Link status is: 0\n");
 		return 0;
 	} else if (GMII_PHY_PHYSR_GIGA == (tmp16 & GMII_PHY_PHYSR_SMASK)) {
 		mode |= AX_MEDIUM_GIGAMODE | AX_MEDIUM_EN_125MHZ;
@@ -1619,6 +1597,8 @@
 
 	netif_carrier_on(dev->net);
 
+	netdev_info(dev->net, "ax88179 - Link status is: 1\n");
+
 	return 0;
 }
 
@@ -1627,7 +1607,7 @@
 	u8 buf[5];
 	u16 *tmp16;
 	u8 *tmp;
-	struct ax88179_data *ax179_data = (struct ax88179_data *)dev->data;
+	struct ax88179_data *ax179_data = dev->driver_priv;
 	struct ethtool_eee eee_data;
 
 	tmp16 = (u16 *)buf;
@@ -1639,17 +1619,18 @@
 
 	*tmp16 = AX_PHYPWR_RSTCTL_IPRL;
 	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, tmp16);
-	msleep(200);
+	msleep(500);
 
 	*tmp = AX_CLK_SELECT_ACS | AX_CLK_SELECT_BCS;
 	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, tmp);
-	msleep(100);
+	msleep(200);
 
 	/* Ethernet PHY Auto Detach*/
-	ax88179_auto_detach(dev, 0);
+	ax88179_auto_detach(dev);
 
 	/* Read MAC address from DTB or asix chip */
 	ax88179_get_mac_addr(dev);
+	memcpy(dev->net->perm_addr, dev->net->dev_addr, ETH_ALEN);
 
 	/* RX bulk configuration */
 	memcpy(tmp, &AX88179_BULKIN_SIZE[0], 5);
@@ -1664,12 +1645,6 @@
 	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PAUSE_WATERLVL_HIGH,
 			  1, 1, tmp);
 
-	dev->net->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
-			      NETIF_F_RXCSUM;
-
-	dev->net->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
-				 NETIF_F_RXCSUM;
-
 	/* Enable checksum offload */
 	*tmp = AX_RXCOE_IP | AX_RXCOE_TCP | AX_RXCOE_UDP |
 	       AX_RXCOE_TCPV6 | AX_RXCOE_UDPV6;
@@ -1695,6 +1670,12 @@
 	ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
 			  2, 2, tmp16);
 
+	/* Check if WoL is supported */
+	ax179_data->wol_supported = 0;
+	if (ax88179_read_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD,
+			     1, 1, &tmp) > 0)
+		ax179_data->wol_supported = WAKE_MAGIC | WAKE_PHY;
+
 	ax88179_led_setting(dev);
 
 	ax179_data->eee_enabled = 0;
@@ -1910,7 +1891,7 @@
 	.suspend =	ax88179_suspend,
 	.resume =	ax88179_resume,
 	.reset_resume =	ax88179_resume,
-	.disconnect =	usbnet_disconnect,
+	.disconnect =	ax88179_disconnect,
 	.supports_autosuspend = 1,
 	.disable_hub_initiated_lpm = 1,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/catc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/catc.c
@@ -615,7 +615,7 @@
  * Receive modes. Broadcast, Multicast, Promisc.
  */
 
-static void catc_multicast(unsigned char *addr, u8 *multicast)
+static void catc_multicast(const unsigned char *addr, u8 *multicast)
 {
 	u32 crc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/cdc_ether.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/cdc_ether.c
@@ -583,6 +583,11 @@
 	.bInterfaceSubClass	= USB_CDC_SUBCLASS_ETHERNET, \
 	.bInterfaceProtocol	= USB_CDC_PROTO_NONE
 
+#define ZAURUS_FAKE_INTERFACE \
+	.bInterfaceClass	= USB_CLASS_COMM, \
+	.bInterfaceSubClass	= USB_CDC_SUBCLASS_MDLM, \
+	.bInterfaceProtocol	= USB_CDC_PROTO_NONE
+
 /* SA-1100 based Sharp Zaurus ("collie"), or compatible;
  * wire-incompatible with true CDC Ethernet implementations.
  * (And, it seems, needlessly so...)
@@ -612,6 +617,13 @@
 	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
 			  | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor		= 0x04DD,
+	.idProduct		= 0x8005,   /* A-300 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info        = 0,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			  | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
 	.idProduct		= 0x8006,	/* B-500/SL-5600 */
 	ZAURUS_MASTER_INTERFACE,
 	.driver_info		= 0,
@@ -619,11 +631,25 @@
 	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
 			  | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor		= 0x04DD,
+	.idProduct		= 0x8006,   /* B-500/SL-5600 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info        = 0,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			  | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
 	.idProduct		= 0x8007,	/* C-700 */
 	ZAURUS_MASTER_INTERFACE,
 	.driver_info		= 0,
 }, {
 	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			  | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
+	.idProduct		= 0x8007,   /* C-700 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info        = 0,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
 		 | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor               = 0x04DD,
 	.idProduct              = 0x9031,	/* C-750 C-760 */
@@ -640,6 +666,13 @@
 	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
 		 | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor               = 0x04DD,
+	.idProduct              = 0x9032,	/* SL-6000 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info		= 0,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+		 | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor               = 0x04DD,
 	/* reported with some C860 units */
 	.idProduct              = 0x9050,	/* C-860 */
 	ZAURUS_MASTER_INTERFACE,
@@ -764,6 +797,13 @@
 },
 #endif
 
+/* Lenovo ThinkPad OneLink+ Dock (based on Realtek RTL8153) */
+{
+	USB_DEVICE_AND_INTERFACE_INFO(LENOVO_VENDOR_ID, 0x3054, USB_CLASS_COMM,
+			USB_CDC_SUBCLASS_ETHERNET, USB_CDC_PROTO_NONE),
+	.driver_info = 0,
+},
+
 /* ThinkPad USB-C Dock (based on Realtek RTL8153) */
 {
 	USB_DEVICE_AND_INTERFACE_INFO(LENOVO_VENDOR_ID, 0x3062, USB_CLASS_COMM,
@@ -981,6 +1021,12 @@
 				      USB_CDC_SUBCLASS_ETHERNET,
 				      USB_CDC_PROTO_NONE),
 	.driver_info = (unsigned long)&wwan_info,
+}, {
+	/* Cinterion PLS62-W modem by GEMALTO/THALES */
+	USB_DEVICE_AND_INTERFACE_INFO(0x1e2d, 0x005b, USB_CLASS_COMM,
+				      USB_CDC_SUBCLASS_ETHERNET,
+				      USB_CDC_PROTO_NONE),
+	.driver_info = (unsigned long)&wwan_info,
 }, {
 	/* Cinterion PLS83/PLS63 modem by GEMALTO/THALES */
 	USB_DEVICE_AND_INTERFACE_INFO(0x1e2d, 0x0069, USB_CLASS_COMM,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/cdc_mbim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/cdc_mbim.c
@@ -659,6 +659,16 @@
 	  .driver_info = (unsigned long)&cdc_mbim_info_avoid_altsetting_toggle,
 	},
 
+	/* Telit FN990 */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x1bc7, 0x1071, USB_CLASS_COMM, USB_CDC_SUBCLASS_MBIM, USB_CDC_PROTO_NONE),
+	  .driver_info = (unsigned long)&cdc_mbim_info_avoid_altsetting_toggle,
+	},
+
+	/* Telit FE990 */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x1bc7, 0x1081, USB_CLASS_COMM, USB_CDC_SUBCLASS_MBIM, USB_CDC_PROTO_NONE),
+	  .driver_info = (unsigned long)&cdc_mbim_info_avoid_altsetting_toggle,
+	},
+
 	/* default entry */
 	{ USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_MBIM, USB_CDC_PROTO_NONE),
 	  .driver_info = (unsigned long)&cdc_mbim_info_zlp,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/cdc_ncm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/cdc_ncm.c
@@ -180,7 +180,12 @@
 	else
 		min = ctx->max_datagram_size + ctx->max_ndp_size + sizeof(struct usb_cdc_ncm_nth32);
 
-	max = min_t(u32, CDC_NCM_NTB_MAX_SIZE_TX, le32_to_cpu(ctx->ncm_parm.dwNtbOutMaxSize));
+	if (le32_to_cpu(ctx->ncm_parm.dwNtbOutMaxSize) == 0)
+		max = CDC_NCM_NTB_MAX_SIZE_TX; /* dwNtbOutMaxSize not set */
+	else
+		max = clamp_t(u32, le32_to_cpu(ctx->ncm_parm.dwNtbOutMaxSize),
+			      USB_CDC_NCM_NTB_MIN_OUT_SIZE,
+			      CDC_NCM_NTB_MAX_SIZE_TX);
 
 	/* some devices set dwNtbOutMaxSize too low for the above default */
 	min = min(min, max);
@@ -1241,6 +1246,9 @@
 			 * further.
 			 */
 			if (skb_out == NULL) {
+				/* If even the smallest allocation fails, abort. */
+				if (ctx->tx_curr_size == USB_CDC_NCM_NTB_MIN_OUT_SIZE)
+					goto alloc_failed;
 				ctx->tx_low_mem_max_cnt = min(ctx->tx_low_mem_max_cnt + 1,
 							      (unsigned)CDC_NCM_LOW_MEM_MAX_CNT);
 				ctx->tx_low_mem_val = ctx->tx_low_mem_max_cnt;
@@ -1259,13 +1267,8 @@
 			skb_out = alloc_skb(ctx->tx_curr_size, GFP_ATOMIC);
 
 			/* No allocation possible so we will abort */
-			if (skb_out == NULL) {
-				if (skb != NULL) {
-					dev_kfree_skb_any(skb);
-					dev->net->stats.tx_dropped++;
-				}
-				goto exit_no_skb;
-			}
+			if (!skb_out)
+				goto alloc_failed;
 			ctx->tx_low_mem_val--;
 		}
 		if (ctx->is_ndp16) {
@@ -1458,6 +1461,11 @@
 
 	return skb_out;
 
+alloc_failed:
+	if (skb) {
+		dev_kfree_skb_any(skb);
+		dev->net->stats.tx_dropped++;
+	}
 exit_no_skb:
 	/* Start timer, if there is a remaining non-empty skb */
 	if (ctx->tx_curr_skb != NULL && n > 0)
@@ -1713,10 +1721,10 @@
 {
 	struct sk_buff *skb;
 	struct cdc_ncm_ctx *ctx = (struct cdc_ncm_ctx *)dev->data[0];
-	int len;
+	unsigned int len;
 	int nframes;
 	int x;
-	int offset;
+	unsigned int offset;
 	union {
 		struct usb_cdc_ncm_ndp16 *ndp16;
 		struct usb_cdc_ncm_ndp32 *ndp32;
@@ -1788,8 +1796,8 @@
 			break;
 		}
 
-		/* sanity checking */
-		if (((offset + len) > skb_in->len) ||
+		/* sanity checking - watch out for integer wrap*/
+		if ((offset > skb_in->len) || (len > skb_in->len - offset) ||
 				(len > ctx->rx_max) || (len < ETH_HLEN)) {
 			netif_dbg(dev, rx_err, dev->net,
 				  "invalid frame detected (ignored) offset[%u]=%u, length=%u, skb=%p\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/ch9200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/ch9200.c
@@ -336,6 +336,7 @@
 {
 	int retval = 0;
 	unsigned char data[2];
+	u8 addr[ETH_ALEN];
 
 	retval = usbnet_get_endpoints(dev, intf);
 	if (retval)
@@ -383,7 +384,8 @@
 	retval = control_write(dev, REQUEST_WRITE, 0, MAC_REG_CTRL, data, 0x02,
 			       CONTROL_TIMEOUT_MS);
 
-	retval = get_mac_address(dev, dev->net->dev_addr);
+	retval = get_mac_address(dev, addr);
+	eth_hw_addr_set(dev->net, addr);
 
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/cx82310_eth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/cx82310_eth.c
@@ -146,6 +146,7 @@
 	u8 link[3];
 	int timeout = 50;
 	struct cx82310_priv *priv;
+	u8 addr[ETH_ALEN];
 
 	/* avoid ADSL modems - continue only if iProduct is "USB NET CARD" */
 	if (usb_string(udev, udev->descriptor.iProduct, buf, sizeof(buf)) > 0
@@ -202,12 +203,12 @@
 		goto err;
 
 	/* get the MAC address */
-	ret = cx82310_cmd(dev, CMD_GET_MAC_ADDR, true, NULL, 0,
-			  dev->net->dev_addr, ETH_ALEN);
+	ret = cx82310_cmd(dev, CMD_GET_MAC_ADDR, true, NULL, 0, addr, ETH_ALEN);
 	if (ret) {
 		netdev_err(dev->net, "unable to read MAC address: %d\n", ret);
 		goto err;
 	}
+	eth_hw_addr_set(dev->net, addr);
 
 	/* start (does not seem to have any effect?) */
 	ret = cx82310_cmd(dev, CMD_START, false, NULL, 0, NULL, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/dm9601.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/dm9601.c
@@ -93,7 +93,8 @@
 				value, reg, NULL, 0);
 }
 
-static void dm_write_async(struct usbnet *dev, u8 reg, u16 length, void *data)
+static void dm_write_async(struct usbnet *dev, u8 reg, u16 length,
+			   const void *data)
 {
 	usbnet_write_cmd_async(dev, DM_WRITE_REGS,
 			       USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
@@ -221,13 +222,18 @@
 	struct usbnet *dev = netdev_priv(netdev);
 
 	__le16 res;
+	int err;
 
 	if (phy_id) {
 		netdev_dbg(dev->net, "Only internal phy supported\n");
 		return 0;
 	}
 
-	dm_read_shared_word(dev, 1, loc, &res);
+	err = dm_read_shared_word(dev, 1, loc, &res);
+	if (err < 0) {
+		netdev_err(dev->net, "MDIO read error: %d\n", err);
+		return 0;
+	}
 
 	netdev_dbg(dev->net,
 		   "dm9601_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/gl620a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/gl620a.c
@@ -179,9 +179,7 @@
 {
 	dev->hard_mtu = GL_RCV_BUF_SIZE;
 	dev->net->hard_header_len += 4;
-	dev->in = usb_rcvbulkpipe(dev->udev, dev->driver_info->in);
-	dev->out = usb_sndbulkpipe(dev->udev, dev->driver_info->out);
-	return 0;
+	return usbnet_get_endpoints(dev, intf);
 }
 
 static const struct driver_info	genelink_info = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/ipheth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/ipheth.c
@@ -121,7 +121,7 @@
 	if (tx_buf == NULL)
 		goto free_rx_urb;
 
-	rx_buf = usb_alloc_coherent(iphone->udev, IPHETH_BUF_SIZE,
+	rx_buf = usb_alloc_coherent(iphone->udev, IPHETH_BUF_SIZE + IPHETH_IP_ALIGN,
 				    GFP_KERNEL, &rx_urb->transfer_dma);
 	if (rx_buf == NULL)
 		goto free_tx_buf;
@@ -146,7 +146,7 @@
 
 static void ipheth_free_urbs(struct ipheth_device *iphone)
 {
-	usb_free_coherent(iphone->udev, IPHETH_BUF_SIZE, iphone->rx_buf,
+	usb_free_coherent(iphone->udev, IPHETH_BUF_SIZE + IPHETH_IP_ALIGN, iphone->rx_buf,
 			  iphone->rx_urb->transfer_dma);
 	usb_free_coherent(iphone->udev, IPHETH_BUF_SIZE, iphone->tx_buf,
 			  iphone->tx_urb->transfer_dma);
@@ -253,13 +253,14 @@
 			0x02, /* index */
 			dev->ctrl_buf, IPHETH_CTRL_BUF_SIZE,
 			IPHETH_CTRL_TIMEOUT);
-	if (retval < 0) {
+	if (retval <= 0) {
 		dev_err(&dev->intf->dev, "%s: usb_control_msg: %d\n",
 			__func__, retval);
 		return retval;
 	}
 
-	if (dev->ctrl_buf[0] == IPHETH_CARRIER_ON) {
+	if ((retval == 1 && dev->ctrl_buf[0] == IPHETH_CARRIER_ON) ||
+	    (retval >= 2 && dev->ctrl_buf[1] == IPHETH_CARRIER_ON)) {
 		netif_carrier_on(dev->net);
 		if (dev->tx_urb->status != -EINPROGRESS)
 			netif_wake_queue(dev->net);
@@ -317,7 +318,7 @@
 
 	usb_fill_bulk_urb(dev->rx_urb, udev,
 			  usb_rcvbulkpipe(udev, dev->bulk_in),
-			  dev->rx_buf, IPHETH_BUF_SIZE,
+			  dev->rx_buf, IPHETH_BUF_SIZE + IPHETH_IP_ALIGN,
 			  ipheth_rcvbulk_callback,
 			  dev);
 	dev->rx_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
@@ -353,8 +354,8 @@
 {
 	struct ipheth_device *dev = netdev_priv(net);
 
-	cancel_delayed_work_sync(&dev->carrier_work);
 	netif_stop_queue(net);
+	cancel_delayed_work_sync(&dev->carrier_work);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/kalmia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/kalmia.c
@@ -65,8 +65,8 @@
 		init_msg, init_msg_len, &act_len, KALMIA_USB_TIMEOUT);
 	if (status != 0) {
 		netdev_err(dev->net,
-			"Error sending init packet. Status %i, length %i\n",
-			status, act_len);
+			"Error sending init packet. Status %i\n",
+			status);
 		return status;
 	}
 	else if (act_len != init_msg_len) {
@@ -83,8 +83,8 @@
 
 	if (status != 0)
 		netdev_err(dev->net,
-			"Error receiving init result. Status %i, length %i\n",
-			status, act_len);
+			"Error receiving init result. Status %i\n",
+			status);
 	else if (act_len != expected_len)
 		netdev_err(dev->net, "Unexpected init result length: %i\n",
 			act_len);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/kaweth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/kaweth.c
@@ -1044,8 +1044,7 @@
 		goto err_all_but_rxbuf;
 
 	memcpy(netdev->broadcast, &bcast_addr, sizeof(bcast_addr));
-	memcpy(netdev->dev_addr, &kaweth->configuration.hw_addr,
-               sizeof(kaweth->configuration.hw_addr));
+	eth_hw_addr_set(netdev, (u8 *)&kaweth->configuration.hw_addr);
 
 	netdev->netdev_ops = &kaweth_netdev_ops;
 	netdev->watchdog_timeo = KAWETH_TX_TIMEOUT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/lan78xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/lan78xx.c
@@ -76,6 +76,8 @@
 #define LAN7801_USB_PRODUCT_ID		(0x7801)
 #define LAN78XX_EEPROM_MAGIC		(0x78A5)
 #define LAN78XX_OTP_MAGIC		(0x78F3)
+#define AT29M2AF_USB_VENDOR_ID		(0x07C9)
+#define AT29M2AF_USB_PRODUCT_ID	(0x0012)
 
 #define	MII_READ			1
 #define	MII_WRITE			0
@@ -1488,13 +1490,13 @@
 	struct lan78xx_priv *pdata = (struct lan78xx_priv *)(dev->data[0]);
 	int ret;
 
+	if (wol->wolopts & ~WAKE_ALL)
+		return -EINVAL;
+
 	ret = usb_autopm_get_interface(dev->intf);
 	if (ret < 0)
 		return ret;
 
-	if (wol->wolopts & ~WAKE_ALL)
-		return -EINVAL;
-
 	pdata->wol = wol->wolopts;
 
 	device_set_wakeup_enable(&dev->udev->dev, (bool)wol->wolopts);
@@ -1948,33 +1950,8 @@
 static void lan78xx_link_status_change(struct net_device *net)
 {
 	struct phy_device *phydev = net->phydev;
-	int temp;
-
-	/* At forced 100 F/H mode, chip may fail to set mode correctly
-	 * when cable is switched between long(~50+m) and short one.
-	 * As workaround, set to 10 before setting to 100
-	 * at forced 100 F/H mode.
-	 */
-	if (!phydev->autoneg && (phydev->speed == 100)) {
-		/* disable phy interrupt */
-		temp = phy_read(phydev, LAN88XX_INT_MASK);
-		temp &= ~LAN88XX_INT_MASK_MDINTPIN_EN_;
-		phy_write(phydev, LAN88XX_INT_MASK, temp);
 
-		temp = phy_read(phydev, MII_BMCR);
-		temp &= ~(BMCR_SPEED100 | BMCR_SPEED1000);
-		phy_write(phydev, MII_BMCR, temp); /* set to 10 first */
-		temp |= BMCR_SPEED100;
-		phy_write(phydev, MII_BMCR, temp); /* set to 100 later */
-
-		/* clear pending interrupt generated while workaround */
-		temp = phy_read(phydev, LAN88XX_INT_STS);
-
-		/* enable phy interrupt back */
-		temp = phy_read(phydev, LAN88XX_INT_MASK);
-		temp |= LAN88XX_INT_MASK_MDINTPIN_EN_;
-		phy_write(phydev, LAN88XX_INT_MASK, temp);
-	}
+	phy_print_status(phydev);
 }
 
 static int irq_map(struct irq_domain *d, unsigned int irq,
@@ -2228,7 +2205,7 @@
 	if (dev->domain_data.phyirq > 0)
 		phydev->irq = dev->domain_data.phyirq;
 	else
-		phydev->irq = 0;
+		phydev->irq = PHY_POLL;
 	netdev_dbg(dev->net, "phydev->irq = %d\n", phydev->irq);
 
 	/* set to AUTOMDIX */
@@ -2243,6 +2220,7 @@
 		if (dev->chipid == ID_REV_CHIP_ID_7801_) {
 			if (phy_is_pseudo_fixed_link(phydev)) {
 				fixed_phy_unregister(phydev);
+				phy_device_free(phydev);
 			} else {
 				phy_unregister_fixup_for_uid(PHY_KSZ9031RNX,
 							     0xfffffff0);
@@ -2885,7 +2863,8 @@
 	if (dev->chipid == ID_REV_CHIP_ID_7801_)
 		buf &= ~MAC_CR_GMII_EN_;
 
-	if (dev->chipid == ID_REV_CHIP_ID_7800_) {
+	if (dev->chipid == ID_REV_CHIP_ID_7800_ ||
+	    dev->chipid == ID_REV_CHIP_ID_7850_) {
 		ret = lan78xx_read_raw_eeprom(dev, 0, 1, &sig);
 		if (!ret && sig != EEPROM_INDICATOR) {
 			/* Implies there is no external eeprom. Set mac speed */
@@ -2982,7 +2961,8 @@
 done:
 	mutex_unlock(&dev->dev_mutex);
 
-	usb_autopm_put_interface(dev->intf);
+	if (ret < 0)
+		usb_autopm_put_interface(dev->intf);
 
 	return ret;
 }
@@ -3935,13 +3915,13 @@
 	if (!dev)
 		return;
 
-	set_bit(EVENT_DEV_DISCONNECT, &dev->flags);
-
 	udev = interface_to_usbdev(intf);
 	net = dev->net;
 
 	unregister_netdev(net);
 
+	timer_shutdown_sync(&dev->stat_monitor);
+	set_bit(EVENT_DEV_DISCONNECT, &dev->flags);
 	cancel_delayed_work_sync(&dev->wq);
 
 	phydev = net->phydev;
@@ -3951,14 +3931,13 @@
 
 	phy_disconnect(net->phydev);
 
-	if (phy_is_pseudo_fixed_link(phydev))
+	if (phy_is_pseudo_fixed_link(phydev)) {
 		fixed_phy_unregister(phydev);
+		phy_device_free(phydev);
+	}
 
 	usb_scuttle_anchored_urbs(&dev->deferred);
 
-	if (timer_pending(&dev->stat_monitor))
-		del_timer_sync(&dev->stat_monitor);
-
 	lan78xx_unbind(dev, intf);
 
 	usb_kill_urb(dev->urb_intr);
@@ -4734,6 +4713,10 @@
 	/* LAN7801 USB Gigabit Ethernet Device */
 	USB_DEVICE(LAN78XX_USB_VENDOR_ID, LAN7801_USB_PRODUCT_ID),
 	},
+	{
+	/* ATM2-AF USB Gigabit Ethernet Device */
+	USB_DEVICE(AT29M2AF_USB_VENDOR_ID, AT29M2AF_USB_PRODUCT_ID),
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(usb, products);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/mcs7830.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/mcs7830.c
@@ -108,8 +108,16 @@
 
 static int mcs7830_get_reg(struct usbnet *dev, u16 index, u16 size, void *data)
 {
-	return usbnet_read_cmd(dev, MCS7830_RD_BREQ, MCS7830_RD_BMREQ,
-				0x0000, index, data, size);
+	int ret;
+
+	ret = usbnet_read_cmd(dev, MCS7830_RD_BREQ, MCS7830_RD_BMREQ,
+			      0x0000, index, data, size);
+	if (ret < 0)
+		return ret;
+	else if (ret < size)
+		return -ENODATA;
+
+	return ret;
 }
 
 static int mcs7830_set_reg(struct usbnet *dev, u16 index, u16 size, const void *data)
@@ -132,7 +140,8 @@
 	return 0;
 }
 
-static int mcs7830_hif_set_mac_address(struct usbnet *dev, unsigned char *addr)
+static int mcs7830_hif_set_mac_address(struct usbnet *dev,
+				       const unsigned char *addr)
 {
 	int ret = mcs7830_set_reg(dev, HIF_REG_ETHERNET_ADDR, ETH_ALEN, addr);
 
@@ -472,17 +481,19 @@
 static int mcs7830_bind(struct usbnet *dev, struct usb_interface *udev)
 {
 	struct net_device *net = dev->net;
+	u8 addr[ETH_ALEN];
 	int ret;
 	int retry;
 
 	/* Initial startup: Gather MAC address setting from EEPROM */
 	ret = -EINVAL;
 	for (retry = 0; retry < 5 && ret; retry++)
-		ret = mcs7830_hif_get_mac_address(dev, net->dev_addr);
+		ret = mcs7830_hif_get_mac_address(dev, addr);
 	if (ret) {
 		dev_warn(&dev->udev->dev, "Cannot read MAC address\n");
 		goto out;
 	}
+	eth_hw_addr_set(net, addr);
 
 	mcs7830_data_set_multicast(net);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/pegasus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/pegasus.c
@@ -493,11 +493,11 @@
 		goto goon;
 
 	rx_status = buf[count - 2];
-	if (rx_status & 0x1e) {
+	if (rx_status & 0x1c) {
 		netif_dbg(pegasus, rx_err, net,
 			  "RX packet error %x\n", rx_status);
 		net->stats.rx_errors++;
-		if (rx_status & 0x06)	/* long or runt	*/
+		if (rx_status & 0x04)	/* runt	*/
 			net->stats.rx_length_errors++;
 		if (rx_status & 0x08)
 			net->stats.rx_crc_errors++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/plusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/plusb.c
@@ -57,9 +57,7 @@
 static inline int
 pl_vendor_req(struct usbnet *dev, u8 req, u8 val, u8 index)
 {
-	return usbnet_read_cmd(dev, req,
-				USB_DIR_IN | USB_TYPE_VENDOR |
-				USB_RECIP_DEVICE,
+	return usbnet_write_cmd(dev, req, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 				val, index, NULL, 0);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/qmi_wwan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/qmi_wwan.c
@@ -201,6 +201,7 @@
 			break;
 		default:
 			/* not ip - do not know what to do */
+			kfree_skb(skbn);
 			goto skip;
 		}
 
@@ -1080,11 +1081,13 @@
 		USB_DEVICE_AND_INTERFACE_INFO(0x03f0, 0x581d, USB_CLASS_VENDOR_SPEC, 1, 7),
 		.driver_info = (unsigned long)&qmi_wwan_info,
 	},
+	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0122)},	/* Quectel RG650V */
 	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0125)},	/* Quectel EC25, EC20 R2.0  Mini PCIe */
 	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0306)},	/* Quectel EP06/EG06/EM06 */
 	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0512)},	/* Quectel EG12/EM12 */
 	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0620)},	/* Quectel EM160R-GL */
 	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0800)},	/* Quectel RM500Q-GL */
+	{QMI_MATCH_FF_FF_FF(0x2c7c, 0x0801)},	/* Quectel RM520N */
 
 	/* 3. Combined interface devices matching on interface number */
 	{QMI_FIXED_INTF(0x0408, 0xea42, 4)},	/* Yota / Megafon M100-1 */
@@ -1216,7 +1219,9 @@
 	{QMI_FIXED_INTF(0x05c6, 0x9080, 8)},
 	{QMI_FIXED_INTF(0x05c6, 0x9083, 3)},
 	{QMI_FIXED_INTF(0x05c6, 0x9084, 4)},
+	{QMI_QUIRK_SET_DTR(0x05c6, 0x9091, 2)},	/* Compal RXM-G1 */
 	{QMI_FIXED_INTF(0x05c6, 0x90b2, 3)},    /* ublox R410M */
+	{QMI_QUIRK_SET_DTR(0x05c6, 0x90db, 2)},	/* Compal RXM-G1 */
 	{QMI_FIXED_INTF(0x05c6, 0x920d, 0)},
 	{QMI_FIXED_INTF(0x05c6, 0x920d, 5)},
 	{QMI_QUIRK_SET_DTR(0x05c6, 0x9625, 4)},	/* YUGA CLM920-NC5 */
@@ -1283,6 +1288,7 @@
 	{QMI_FIXED_INTF(0x19d2, 0x0168, 4)},
 	{QMI_FIXED_INTF(0x19d2, 0x0176, 3)},
 	{QMI_FIXED_INTF(0x19d2, 0x0178, 3)},
+	{QMI_FIXED_INTF(0x19d2, 0x0189, 4)},    /* ZTE MF290 */
 	{QMI_FIXED_INTF(0x19d2, 0x0191, 4)},	/* ZTE EuFi890 */
 	{QMI_FIXED_INTF(0x19d2, 0x0199, 1)},	/* ZTE MF820S */
 	{QMI_FIXED_INTF(0x19d2, 0x0200, 1)},
@@ -1320,7 +1326,7 @@
 	{QMI_FIXED_INTF(0x2001, 0x7e3d, 4)},	/* D-Link DWM-222 A2 */
 	{QMI_FIXED_INTF(0x2020, 0x2031, 4)},	/* Olicard 600 */
 	{QMI_FIXED_INTF(0x2020, 0x2033, 4)},	/* BroadMobi BM806U */
-	{QMI_FIXED_INTF(0x2020, 0x2060, 4)},	/* BroadMobi BM818 */
+	{QMI_QUIRK_SET_DTR(0x2020, 0x2060, 4)},	/* BroadMobi BM818 */
 	{QMI_FIXED_INTF(0x0f3d, 0x68a2, 8)},    /* Sierra Wireless MC7700 */
 	{QMI_FIXED_INTF(0x114f, 0x68a2, 8)},    /* Sierra Wireless MC7750 */
 	{QMI_FIXED_INTF(0x1199, 0x68a2, 8)},	/* Sierra Wireless MC7710 in QMI mode */
@@ -1352,9 +1358,20 @@
 	{QMI_FIXED_INTF(0x2357, 0x0201, 4)},	/* TP-LINK HSUPA Modem MA180 */
 	{QMI_FIXED_INTF(0x2357, 0x9000, 4)},	/* TP-LINK MA260 */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1031, 3)}, /* Telit LE910C1-EUX */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x103a, 0)}, /* Telit LE910C4-WWX */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1040, 2)},	/* Telit LE922A */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1050, 2)},	/* Telit FN980 */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1060, 2)},	/* Telit LN920 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1070, 2)},	/* Telit FN990 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1080, 2)}, /* Telit FE990 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10a0, 0)}, /* Telit FN920C04 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10a4, 0)}, /* Telit FN920C04 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10a9, 0)}, /* Telit FN920C04 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10b0, 0)}, /* Telit FE990B */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10c0, 0)}, /* Telit FE910C04 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10c4, 0)}, /* Telit FE910C04 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10c8, 0)}, /* Telit FE910C04 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x10d0, 0)}, /* Telit FN990B */
 	{QMI_FIXED_INTF(0x1bc7, 0x1100, 3)},	/* Telit ME910 */
 	{QMI_FIXED_INTF(0x1bc7, 0x1101, 3)},	/* Telit ME910 dual modem */
 	{QMI_FIXED_INTF(0x1bc7, 0x1200, 5)},	/* Telit LE920 */
@@ -1363,6 +1380,8 @@
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1260, 2)},	/* Telit LE910Cx */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1261, 2)},	/* Telit LE910Cx */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1900, 1)},	/* Telit LN940 series */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x3000, 0)},	/* Telit FN912 series */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x3001, 0)},	/* Telit FN912 series */
 	{QMI_FIXED_INTF(0x1c9e, 0x9801, 3)},	/* Telewell TW-3G HSPA+ */
 	{QMI_FIXED_INTF(0x1c9e, 0x9803, 4)},	/* Telewell TW-3G HSPA+ */
 	{QMI_FIXED_INTF(0x1c9e, 0x9b01, 3)},	/* XS Stick W100-2 from 4G Systems */
@@ -1391,10 +1410,13 @@
 	{QMI_FIXED_INTF(0x413c, 0x81b3, 8)},	/* Dell Wireless 5809e Gobi(TM) 4G LTE Mobile Broadband Card (rev3) */
 	{QMI_FIXED_INTF(0x413c, 0x81b6, 8)},	/* Dell Wireless 5811e */
 	{QMI_FIXED_INTF(0x413c, 0x81b6, 10)},	/* Dell Wireless 5811e */
+	{QMI_FIXED_INTF(0x413c, 0x81c2, 8)},	/* Dell Wireless 5811e */
 	{QMI_FIXED_INTF(0x413c, 0x81cc, 8)},	/* Dell Wireless 5816e */
 	{QMI_FIXED_INTF(0x413c, 0x81d7, 0)},	/* Dell Wireless 5821e */
 	{QMI_FIXED_INTF(0x413c, 0x81d7, 1)},	/* Dell Wireless 5821e preproduction config */
 	{QMI_FIXED_INTF(0x413c, 0x81e0, 0)},	/* Dell Wireless 5821e with eSIM support*/
+	{QMI_FIXED_INTF(0x413c, 0x81e4, 0)},	/* Dell Wireless 5829e with eSIM support*/
+	{QMI_FIXED_INTF(0x413c, 0x81e6, 0)},	/* Dell Wireless 5829e */
 	{QMI_FIXED_INTF(0x03f0, 0x4e1d, 8)},	/* HP lt4111 LTE/EV-DO/HSPA+ Gobi 4G Module */
 	{QMI_FIXED_INTF(0x03f0, 0x9d1d, 1)},	/* HP lt4120 Snapdragon X5 LTE */
 	{QMI_FIXED_INTF(0x22de, 0x9061, 3)},	/* WeTelecom WPD-600N */
@@ -1403,10 +1425,15 @@
 	{QMI_QUIRK_SET_DTR(0x2c7c, 0x0191, 4)},	/* Quectel EG91 */
 	{QMI_QUIRK_SET_DTR(0x2c7c, 0x0195, 4)},	/* Quectel EG95 */
 	{QMI_FIXED_INTF(0x2c7c, 0x0296, 4)},	/* Quectel BG96 */
+	{QMI_QUIRK_SET_DTR(0x2c7c, 0x030e, 4)},	/* Quectel EM05GV2 */
 	{QMI_QUIRK_SET_DTR(0x2cb7, 0x0104, 4)},	/* Fibocom NL678 series */
+	{QMI_QUIRK_SET_DTR(0x2cb7, 0x0112, 0)},	/* Fibocom FG132 */
 	{QMI_FIXED_INTF(0x0489, 0xe0b4, 0)},	/* Foxconn T77W968 LTE */
 	{QMI_FIXED_INTF(0x0489, 0xe0b5, 0)},	/* Foxconn T77W968 LTE with eSIM support*/
 	{QMI_FIXED_INTF(0x2692, 0x9025, 4)},    /* Cellient MPL200 (rebranded Qualcomm 05c6:9025) */
+	{QMI_QUIRK_SET_DTR(0x1546, 0x1342, 4)},	/* u-blox LARA-L6 */
+	{QMI_QUIRK_SET_DTR(0x33f8, 0x0104, 4)}, /* Rolling RW101 RMNET */
+	{QMI_FIXED_INTF(0x2dee, 0x4d22, 5)},    /* MeiG Smart SRM825L */
 
 	/* 4. Gobi 1000 devices */
 	{QMI_GOBI1K_DEVICE(0x05c6, 0x9212)},	/* Acer Gobi Modem Device */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/r8152.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/r8152.c
@@ -32,7 +32,7 @@
 #define NETNEXT_VERSION		"12"
 
 /* Information for net */
-#define NET_VERSION		"11"
+#define NET_VERSION		"13"
 
 #define DRIVER_VERSION		"v1." NETNEXT_VERSION "." NET_VERSION
 #define DRIVER_AUTHOR "Realtek linux nic maintainers <nic_swsd@realtek.com>"
@@ -199,6 +199,7 @@
 #define OCP_EEE_AR		0xa41a
 #define OCP_EEE_DATA		0xa41c
 #define OCP_PHY_STATUS		0xa420
+#define OCP_INTR_EN		0xa424
 #define OCP_NCTL_CFG		0xa42c
 #define OCP_POWER_CFG		0xa430
 #define OCP_EEE_CFG		0xa432
@@ -620,6 +621,9 @@
 #define PHY_STAT_LAN_ON		3
 #define PHY_STAT_PWRDN		5
 
+/* OCP_INTR_EN */
+#define INTR_SPEED_FORCE	BIT(3)
+
 /* OCP_NCTL_CFG */
 #define PGA_RETURN_EN		BIT(1)
 
@@ -759,7 +763,7 @@
 
 /* rtl8152 flags */
 enum rtl8152_flags {
-	RTL8152_UNPLUG = 0,
+	RTL8152_INACCESSIBLE = 0,
 	RTL8152_SET_RX_MODE,
 	WORK_ENABLE,
 	RTL8152_LINK_CHG,
@@ -770,6 +774,7 @@
 	RX_EPROTO,
 };
 
+#define DEVICE_ID_THINKPAD_ONELINK_PLUS_DOCK		0x3054
 #define DEVICE_ID_THINKPAD_THUNDERBOLT3_DOCK_GEN2	0x3082
 #define DEVICE_ID_THINKPAD_USB_C_DOCK_GEN2		0xa387
 
@@ -1203,7 +1208,7 @@
 
 	ret = usb_control_msg(tp->udev, tp->pipe_ctrl_in,
 			      RTL8152_REQ_GET_REGS, RTL8152_REQT_READ,
-			      value, index, tmp, size, 500);
+			      value, index, tmp, size, USB_CTRL_GET_TIMEOUT);
 	if (ret < 0)
 		memset(data, 0xff, size);
 	else
@@ -1226,7 +1231,7 @@
 
 	ret = usb_control_msg(tp->udev, tp->pipe_ctrl_out,
 			      RTL8152_REQ_SET_REGS, RTL8152_REQT_WRITE,
-			      value, index, tmp, size, 500);
+			      value, index, tmp, size, USB_CTRL_SET_TIMEOUT);
 
 	kfree(tmp);
 
@@ -1236,7 +1241,7 @@
 static void rtl_set_unplug(struct r8152 *tp)
 {
 	if (tp->udev->state == USB_STATE_NOTATTACHED) {
-		set_bit(RTL8152_UNPLUG, &tp->flags);
+		set_bit(RTL8152_INACCESSIBLE, &tp->flags);
 		smp_mb__after_atomic();
 	}
 }
@@ -1247,7 +1252,7 @@
 	u16 limit = 64;
 	int ret = 0;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	/* both size and indix must be 4 bytes align */
@@ -1291,7 +1296,7 @@
 	u16 byteen_start, byteen_end, byen;
 	u16 limit = 512;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	/* both size and indix must be 4 bytes align */
@@ -1521,7 +1526,7 @@
 	struct r8152 *tp = netdev_priv(netdev);
 	int ret;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	if (phy_id != R8152_PHY_ID)
@@ -1537,7 +1542,7 @@
 {
 	struct r8152 *tp = netdev_priv(netdev);
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	if (phy_id != R8152_PHY_ID)
@@ -1742,7 +1747,7 @@
 	if (!tp)
 		return;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	if (!test_bit(WORK_ENABLE, &tp->flags))
@@ -1834,7 +1839,7 @@
 	if (!test_bit(WORK_ENABLE, &tp->flags))
 		return;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	if (!skb_queue_empty(&tp->tx_queue))
@@ -1855,7 +1860,7 @@
 	if (!test_bit(WORK_ENABLE, &tp->flags))
 		return;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	switch (status) {
@@ -1871,7 +1876,9 @@
 			   "Stop submitting intr, status %d\n", status);
 		return;
 	case -EOVERFLOW:
-		netif_info(tp, intr, tp->netdev, "intr status -EOVERFLOW\n");
+		if (net_ratelimit())
+			netif_info(tp, intr, tp->netdev,
+				   "intr status -EOVERFLOW\n");
 		goto resubmit;
 	/* -EPIPE:  should clear the halt */
 	default:
@@ -2597,7 +2604,7 @@
 {
 	struct r8152 *tp = from_tasklet(tp, t, tx_tl);
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	if (!test_bit(WORK_ENABLE, &tp->flags))
@@ -2618,6 +2625,9 @@
 	struct r8152 *tp = container_of(napi, struct r8152, napi);
 	int work_done;
 
+	if (!budget)
+		return 0;
+
 	work_done = rx_bottom(tp, budget);
 
 	if (work_done < budget) {
@@ -2637,7 +2647,7 @@
 	int ret;
 
 	/* The rx would be stopped, so skip submitting */
-	if (test_bit(RTL8152_UNPLUG, &tp->flags) ||
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags) ||
 	    !test_bit(WORK_ENABLE, &tp->flags) || !netif_carrier_ok(tp->netdev))
 		return 0;
 
@@ -2840,6 +2850,8 @@
 		ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CR, CR_RST);
 
 		for (i = 0; i < 1000; i++) {
+			if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+				break;
 			if (!(ocp_read_byte(tp, MCU_TYPE_PLA, PLA_CR) & CR_RST))
 				break;
 			usleep_range(100, 400);
@@ -3013,12 +3025,16 @@
 	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CR, ocp_data);
 
 	switch (tp->version) {
-	case RTL_VER_08:
-	case RTL_VER_09:
-	case RTL_VER_14:
-		r8153b_rx_agg_chg_indicate(tp);
+	case RTL_VER_01:
+	case RTL_VER_02:
+	case RTL_VER_03:
+	case RTL_VER_04:
+	case RTL_VER_05:
+	case RTL_VER_06:
+	case RTL_VER_07:
 		break;
 	default:
+		r8153b_rx_agg_chg_indicate(tp);
 		break;
 	}
 
@@ -3029,7 +3045,7 @@
 
 static int rtl8152_enable(struct r8152 *tp)
 {
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	set_tx_qlen(tp);
@@ -3072,7 +3088,6 @@
 			       640 / 8);
 		ocp_write_word(tp, MCU_TYPE_USB, USB_RX_EXTRA_AGGR_TMR,
 			       ocp_data);
-		r8153b_rx_agg_chg_indicate(tp);
 		break;
 
 	default:
@@ -3106,7 +3121,6 @@
 	case RTL_VER_15:
 		ocp_write_word(tp, MCU_TYPE_USB, USB_RX_EARLY_SIZE,
 			       ocp_data / 8);
-		r8153b_rx_agg_chg_indicate(tp);
 		break;
 	default:
 		WARN_ON_ONCE(1);
@@ -3118,7 +3132,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	set_tx_qlen(tp);
@@ -3150,7 +3164,7 @@
 	u32 ocp_data;
 	int i;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags)) {
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags)) {
 		rtl_drop_queued_tx(tp);
 		return;
 	}
@@ -3167,6 +3181,8 @@
 	rxdy_gated_en(tp, true);
 
 	for (i = 0; i < 1000; i++) {
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+			break;
 		ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
 		if ((ocp_data & FIFO_EMPTY) == FIFO_EMPTY)
 			break;
@@ -3174,6 +3190,8 @@
 	}
 
 	for (i = 0; i < 1000; i++) {
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+			break;
 		if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR0) & TCR0_TX_EMPTY)
 			break;
 		usleep_range(1000, 2000);
@@ -3604,7 +3622,7 @@
 		}
 
 		msleep(20);
-		if (test_bit(RTL8152_UNPLUG, &tp->flags))
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 			break;
 	}
 
@@ -3636,6 +3654,8 @@
 			int i;
 
 			for (i = 0; i < 500; i++) {
+				if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+					return;
 				if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
 				    AUTOLOAD_DONE)
 					break;
@@ -3676,6 +3696,8 @@
 			int i;
 
 			for (i = 0; i < 500; i++) {
+				if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+					return;
 				if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
 				    AUTOLOAD_DONE)
 					break;
@@ -4016,6 +4038,11 @@
 	ocp_write_word(tp, type, PLA_BP_BA, 0);
 }
 
+static inline void rtl_reset_ocp_base(struct r8152 *tp)
+{
+	tp->ocp_base = -1;
+}
+
 static int rtl_phy_patch_request(struct r8152 *tp, bool request, bool wait)
 {
 	u16 data, check;
@@ -4034,6 +4061,9 @@
 	for (i = 0; wait && i < 5000; i++) {
 		u32 ocp_data;
 
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+			return -ENODEV;
+
 		usleep_range(1000, 2000);
 		ocp_data = ocp_reg_read(tp, OCP_PHY_PATCH_STAT);
 		if ((ocp_data & PATCH_READY) ^ check)
@@ -4087,8 +4117,6 @@
 
 	rtl_phy_patch_request(tp, false, wait);
 
-	ocp_write_word(tp, MCU_TYPE_PLA, PLA_OCP_GPHY_BASE, tp->ocp_base);
-
 	return 0;
 }
 
@@ -4800,6 +4828,8 @@
 	u32 len;
 	u8 *data;
 
+	rtl_reset_ocp_base(tp);
+
 	if (sram_read(tp, SRAM_GPHY_FW_VER) >= __le16_to_cpu(phy->version)) {
 		dev_dbg(&tp->intf->dev, "PHY firmware has been the newest\n");
 		return;
@@ -4845,7 +4875,8 @@
 		}
 	}
 
-	ocp_write_word(tp, MCU_TYPE_PLA, PLA_OCP_GPHY_BASE, tp->ocp_base);
+	rtl_reset_ocp_base(tp);
+
 	rtl_phy_patch_request(tp, false, wait);
 
 	if (sram_read(tp, SRAM_GPHY_FW_VER) == __le16_to_cpu(phy->version))
@@ -4861,6 +4892,8 @@
 	ver_addr = __le16_to_cpu(phy_ver->ver.addr);
 	ver = __le16_to_cpu(phy_ver->ver.data);
 
+	rtl_reset_ocp_base(tp);
+
 	if (sram_read(tp, ver_addr) >= ver) {
 		dev_dbg(&tp->intf->dev, "PHY firmware has been the newest\n");
 		return 0;
@@ -4877,6 +4910,8 @@
 {
 	u16 addr, data;
 
+	rtl_reset_ocp_base(tp);
+
 	addr = __le16_to_cpu(fix->setting.addr);
 	data = ocp_reg_read(tp, addr);
 
@@ -4908,6 +4943,8 @@
 	u32 length;
 	int i, num;
 
+	rtl_reset_ocp_base(tp);
+
 	num = phy->pre_num;
 	for (i = 0; i < num; i++)
 		sram_write(tp, __le16_to_cpu(phy->pre_set[i].addr),
@@ -4938,6 +4975,8 @@
 	u32 length, i, num;
 	__le16 *data;
 
+	rtl_reset_ocp_base(tp);
+
 	mode_reg = __le16_to_cpu(phy->mode_reg);
 	sram_write(tp, mode_reg, __le16_to_cpu(phy->mode_pre));
 	sram_write(tp, __le16_to_cpu(phy->ba_reg),
@@ -5107,6 +5146,7 @@
 	if (rtl_fw->post_fw)
 		rtl_fw->post_fw(tp);
 
+	rtl_reset_ocp_base(tp);
 	strscpy(rtl_fw->version, fw_hdr->version, RTL_VER_SIZE);
 	dev_info(&tp->intf->dev, "load %s successfully\n", rtl_fw->version);
 }
@@ -5340,6 +5380,8 @@
 	int i;
 
 	for (i = 0; i < 1000; i++) {
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+			break;
 		ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL);
 		if (ocp_data & LINK_LIST_READY)
 			break;
@@ -5354,6 +5396,8 @@
 		int i;
 
 		for (i = 0; i < 100; i++) {
+			if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+				break;
 			if (ocp_read_word(tp, MCU_TYPE_USB, USB_GPHY_CTRL) & GPHY_PATCH_DONE)
 				break;
 			usleep_range(1000, 2000);
@@ -5476,6 +5520,8 @@
 	for (i = 0; i < 104; i++) {
 		u32 ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_WDT1_CTRL);
 
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+			return -ENODEV;
 		if (!(ocp_data & WTD1_EN))
 			break;
 		usleep_range(1000, 2000);
@@ -5632,6 +5678,8 @@
 		data &= ~EN_ALDPS;
 		ocp_reg_write(tp, OCP_POWER_CFG, data);
 		for (i = 0; i < 20; i++) {
+			if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
+				return;
 			usleep_range(1000, 2000);
 			if (ocp_read_word(tp, MCU_TYPE_PLA, 0xe000) & 0x0100)
 				break;
@@ -5889,6 +5937,11 @@
 	ocp_data &= ~NOW_IS_OOB;
 	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
 
+	/* RX FIFO settings for OOB */
+	ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL0, RXFIFO_THR1_OOB);
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL1, RXFIFO_THR2_OOB);
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_CTRL2, RXFIFO_THR3_OOB);
+
 	rtl_disable(tp);
 	rtl_reset_bmu(tp);
 
@@ -5900,7 +5953,8 @@
 
 	wait_oob_link_list_ready(tp);
 
-	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, mtu_to_size(tp->netdev->mtu));
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, 1522);
+	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_MTPS, MTPS_DEFAULT);
 
 	switch (tp->version) {
 	case RTL_VER_03:
@@ -5936,6 +5990,10 @@
 	ocp_data |= NOW_IS_OOB | DIS_MCU_CLROOB;
 	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
 
+	ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7);
+	ocp_data |= MCU_BORW_EN;
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data);
+
 	rxdy_gated_en(tp, false);
 
 	ocp_data = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR);
@@ -5951,14 +6009,34 @@
 	r8153_aldps_en(tp, true);
 }
 
+static u32 fc_pause_on_auto(struct r8152 *tp)
+{
+	return (ALIGN(mtu_to_size(tp->netdev->mtu), 1024) + 6 * 1024);
+}
+
+static u32 fc_pause_off_auto(struct r8152 *tp)
+{
+	return (ALIGN(mtu_to_size(tp->netdev->mtu), 1024) + 14 * 1024);
+}
+
+static void r8156_fc_parameter(struct r8152 *tp)
+{
+	u32 pause_on = tp->fc_pause_on ? tp->fc_pause_on : fc_pause_on_auto(tp);
+	u32 pause_off = tp->fc_pause_off ? tp->fc_pause_off : fc_pause_off_auto(tp);
+
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_FULL, pause_on / 16);
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_EMPTY, pause_off / 16);
+}
+
 static int rtl8156_enable(struct r8152 *tp)
 {
 	u32 ocp_data;
 	u16 speed;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
+	r8156_fc_parameter(tp);
 	set_tx_qlen(tp);
 	rtl_set_eee_plus(tp);
 	r8153_set_rx_early_timeout(tp);
@@ -5990,15 +6068,30 @@
 		ocp_write_word(tp, MCU_TYPE_USB, USB_L1_CTRL, ocp_data);
 	}
 
+	ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_FW_TASK);
+	ocp_data &= ~FC_PATCH_TASK;
+	ocp_write_word(tp, MCU_TYPE_USB, USB_FW_TASK, ocp_data);
+	usleep_range(1000, 2000);
+	ocp_data |= FC_PATCH_TASK;
+	ocp_write_word(tp, MCU_TYPE_USB, USB_FW_TASK, ocp_data);
+
 	return rtl_enable(tp);
 }
 
+static void rtl8156_disable(struct r8152 *tp)
+{
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_FULL, 0);
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_EMPTY, 0);
+
+	rtl8153_disable(tp);
+}
+
 static int rtl8156b_enable(struct r8152 *tp)
 {
 	u32 ocp_data;
 	u16 speed;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	set_tx_qlen(tp);
@@ -6184,7 +6277,7 @@
 
 static void rtl8152_up(struct r8152 *tp)
 {
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8152_aldps_en(tp, false);
@@ -6194,7 +6287,7 @@
 
 static void rtl8152_down(struct r8152 *tp)
 {
-	if (test_bit(RTL8152_UNPLUG, &tp->flags)) {
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags)) {
 		rtl_drop_queued_tx(tp);
 		return;
 	}
@@ -6209,7 +6302,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153_u1u2en(tp, false);
@@ -6249,7 +6342,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags)) {
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags)) {
 		rtl_drop_queued_tx(tp);
 		return;
 	}
@@ -6270,7 +6363,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153b_u1u2en(tp, false);
@@ -6294,7 +6387,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags)) {
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags)) {
 		rtl_drop_queued_tx(tp);
 		return;
 	}
@@ -6331,7 +6424,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153b_u1u2en(tp, false);
@@ -6394,38 +6487,6 @@
 	r8153b_u1u2en(tp, true);
 }
 
-static inline u32 fc_pause_on_auto(struct r8152 *tp)
-{
-	return (ALIGN(mtu_to_size(tp->netdev->mtu), 1024) + 6 * 1024);
-}
-
-static inline u32 fc_pause_off_auto(struct r8152 *tp)
-{
-	return (ALIGN(mtu_to_size(tp->netdev->mtu), 1024) + 14 * 1024);
-}
-
-static void r8156_fc_parameter(struct r8152 *tp)
-{
-	u32 pause_on = tp->fc_pause_on ? tp->fc_pause_on : fc_pause_on_auto(tp);
-	u32 pause_off = tp->fc_pause_off ? tp->fc_pause_off : fc_pause_off_auto(tp);
-
-	switch (tp->version) {
-	case RTL_VER_10:
-	case RTL_VER_11:
-		ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_FULL, pause_on / 8);
-		ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_EMPTY, pause_off / 8);
-		break;
-	case RTL_VER_12:
-	case RTL_VER_13:
-	case RTL_VER_15:
-		ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_FULL, pause_on / 16);
-		ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_EMPTY, pause_off / 16);
-		break;
-	default:
-		break;
-	}
-}
-
 static void rtl8156_change_mtu(struct r8152 *tp)
 {
 	u32 rx_max_size = mtu_to_size(tp->netdev->mtu);
@@ -6444,7 +6505,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153b_u1u2en(tp, false);
@@ -6517,7 +6578,7 @@
 {
 	u32 ocp_data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags)) {
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags)) {
 		rtl_drop_queued_tx(tp);
 		return;
 	}
@@ -6535,9 +6596,17 @@
 	ocp_data &= ~NOW_IS_OOB;
 	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
 
+	/* RX FIFO settings for OOB */
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RXFIFO_FULL, 64 / 16);
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_FULL, 1024 / 16);
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RX_FIFO_EMPTY, 4096 / 16);
+
 	rtl_disable(tp);
 	rtl_reset_bmu(tp);
 
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, 1522);
+	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_MTPS, MTPS_DEFAULT);
+
 	/* Clear teredo wake event. bit[15:8] is the teredo wakeup
 	 * type. Set it to zero. bits[7:0] are the W1C bits about
 	 * the events. Set them to all 1 to clear them.
@@ -6548,6 +6617,10 @@
 	ocp_data |= NOW_IS_OOB;
 	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_OOB_CTRL, ocp_data);
 
+	ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7);
+	ocp_data |= MCU_BORW_EN;
+	ocp_write_word(tp, MCU_TYPE_PLA, PLA_SFF_STS_7, ocp_data);
+
 	rtl_rx_vlan_en(tp, true);
 	rxdy_gated_en(tp, false);
 
@@ -6584,6 +6657,21 @@
 		return true;
 }
 
+static void r8156_mdio_force_mode(struct r8152 *tp)
+{
+	u16 data;
+
+	/* Select force mode through 0xa5b4 bit 15
+	 * 0: MDIO force mode
+	 * 1: MMD force mode
+	 */
+	data = ocp_reg_read(tp, 0xa5b4);
+	if (data & BIT(15)) {
+		data &= ~BIT(15);
+		ocp_reg_write(tp, 0xa5b4, data);
+	}
+}
+
 static void set_carrier(struct r8152 *tp)
 {
 	struct net_device *netdev = tp->netdev;
@@ -6628,7 +6716,7 @@
 	/* If the device is unplugged or !netif_running(), the workqueue
 	 * doesn't need to wake the device, and could return directly.
 	 */
-	if (test_bit(RTL8152_UNPLUG, &tp->flags) || !netif_running(tp->netdev))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags) || !netif_running(tp->netdev))
 		return;
 
 	if (usb_autopm_get_interface(tp->intf) < 0)
@@ -6667,7 +6755,7 @@
 {
 	struct r8152 *tp = container_of(work, struct r8152, hw_phy_work.work);
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	if (usb_autopm_get_interface(tp->intf) < 0)
@@ -6794,7 +6882,7 @@
 	netif_stop_queue(netdev);
 
 	res = usb_autopm_get_interface(tp->intf);
-	if (res < 0 || test_bit(RTL8152_UNPLUG, &tp->flags)) {
+	if (res < 0 || test_bit(RTL8152_INACCESSIBLE, &tp->flags)) {
 		rtl_drop_queued_tx(tp);
 		rtl_stop_rx(tp);
 	} else {
@@ -6827,7 +6915,7 @@
 	u32 ocp_data;
 	u16 data;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	data = r8152_mdio_read(tp, MII_BMCR);
@@ -6871,7 +6959,7 @@
 	u16 data;
 	int i;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153_u1u2en(tp, false);
@@ -6882,7 +6970,7 @@
 			break;
 
 		msleep(20);
-		if (test_bit(RTL8152_UNPLUG, &tp->flags))
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 			break;
 	}
 
@@ -7011,7 +7099,7 @@
 	u16 data;
 	int i;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153b_u1u2en(tp, false);
@@ -7022,7 +7110,7 @@
 			break;
 
 		msleep(20);
-		if (test_bit(RTL8152_UNPLUG, &tp->flags))
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 			break;
 	}
 
@@ -7093,7 +7181,7 @@
 	u16 data;
 	int i;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153b_u1u2en(tp, false);
@@ -7113,7 +7201,7 @@
 			break;
 
 		msleep(20);
-		if (test_bit(RTL8152_UNPLUG, &tp->flags))
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 			return;
 	}
 
@@ -7489,6 +7577,11 @@
 				      ((swap_a & 0x1f) << 8) |
 				      ((swap_a >> 8) & 0x1f));
 		}
+
+		/* Notify the MAC when the speed is changed to force mode. */
+		data = ocp_reg_read(tp, OCP_INTR_EN);
+		data |= INTR_SPEED_FORCE;
+		ocp_reg_write(tp, OCP_INTR_EN, data);
 		break;
 	default:
 		break;
@@ -7884,6 +7977,11 @@
 		break;
 	}
 
+	/* Notify the MAC when the speed is changed to force mode. */
+	data = ocp_reg_read(tp, OCP_INTR_EN);
+	data |= INTR_SPEED_FORCE;
+	ocp_reg_write(tp, OCP_INTR_EN, data);
+
 	if (rtl_phy_patch_request(tp, true, true))
 		return;
 
@@ -7932,7 +8030,7 @@
 	u16 data;
 	int i;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_ECM_OP);
@@ -7953,7 +8051,7 @@
 			break;
 
 		msleep(20);
-		if (test_bit(RTL8152_UNPLUG, &tp->flags))
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 			return;
 	}
 
@@ -8016,6 +8114,7 @@
 	ocp_data |= ACT_ODMA;
 	ocp_write_byte(tp, MCU_TYPE_USB, USB_BMU_CONFIG, ocp_data);
 
+	r8156_mdio_force_mode(tp);
 	rtl_tally_reset(tp);
 
 	tp->coalesce = 15000;	/* 15 us */
@@ -8027,7 +8126,7 @@
 	u16 data;
 	int i;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	ocp_data = ocp_read_byte(tp, MCU_TYPE_USB, USB_ECM_OP);
@@ -8061,7 +8160,7 @@
 			break;
 
 		msleep(20);
-		if (test_bit(RTL8152_UNPLUG, &tp->flags))
+		if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 			return;
 	}
 
@@ -8145,6 +8244,7 @@
 	ocp_data &= ~(RX_AGG_DISABLE | RX_ZERO_EN);
 	ocp_write_word(tp, MCU_TYPE_USB, USB_USB_CTRL, ocp_data);
 
+	r8156_mdio_force_mode(tp);
 	rtl_tally_reset(tp);
 
 	tp->coalesce = 15000;	/* 15 us */
@@ -8181,43 +8281,6 @@
 	return true;
 }
 
-static bool rtl_vendor_mode(struct usb_interface *intf)
-{
-	struct usb_host_interface *alt = intf->cur_altsetting;
-	struct usb_device *udev;
-	struct usb_host_config *c;
-	int i, num_configs;
-
-	if (alt->desc.bInterfaceClass == USB_CLASS_VENDOR_SPEC)
-		return rtl_check_vendor_ok(intf);
-
-	/* The vendor mode is not always config #1, so to find it out. */
-	udev = interface_to_usbdev(intf);
-	c = udev->config;
-	num_configs = udev->descriptor.bNumConfigurations;
-	if (num_configs < 2)
-		return false;
-
-	for (i = 0; i < num_configs; (i++, c++)) {
-		struct usb_interface_descriptor	*desc = NULL;
-
-		if (c->desc.bNumInterfaces > 0)
-			desc = &c->intf_cache[0]->altsetting->desc;
-		else
-			continue;
-
-		if (desc->bInterfaceClass == USB_CLASS_VENDOR_SPEC) {
-			usb_driver_set_configuration(udev, c->desc.bConfigurationValue);
-			break;
-		}
-	}
-
-	if (i == num_configs)
-		dev_err(&intf->dev, "Unexpected Device\n");
-
-	return false;
-}
-
 static int rtl8152_pre_reset(struct usb_interface *intf)
 {
 	struct r8152 *tp = usb_get_intfdata(intf);
@@ -8467,6 +8530,8 @@
 
 	mutex_lock(&tp->control);
 
+	rtl_reset_ocp_base(tp);
+
 	if (test_bit(SELECTIVE_SUSPEND, &tp->flags))
 		ret = rtl8152_runtime_resume(tp);
 	else
@@ -8482,6 +8547,7 @@
 	struct r8152 *tp = usb_get_intfdata(intf);
 
 	clear_bit(SELECTIVE_SUSPEND, &tp->flags);
+	rtl_reset_ocp_base(tp);
 	tp->rtl_ops.init(tp);
 	queue_delayed_work(system_long_wq, &tp->hw_phy_work, 0);
 	set_ethernet_addr(tp, true);
@@ -9119,7 +9185,7 @@
 	struct mii_ioctl_data *data = if_mii(rq);
 	int res;
 
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return -ENODEV;
 
 	res = usb_autopm_get_interface(tp->intf);
@@ -9221,7 +9287,7 @@
 
 static void rtl8152_unload(struct r8152 *tp)
 {
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	if (tp->version != RTL_VER_01)
@@ -9230,7 +9296,7 @@
 
 static void rtl8153_unload(struct r8152 *tp)
 {
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153_power_cut_en(tp, false);
@@ -9238,7 +9304,7 @@
 
 static void rtl8153b_unload(struct r8152 *tp)
 {
-	if (test_bit(RTL8152_UNPLUG, &tp->flags))
+	if (test_bit(RTL8152_INACCESSIBLE, &tp->flags))
 		return;
 
 	r8153b_power_cut_en(tp, false);
@@ -9319,7 +9385,7 @@
 	case RTL_VER_10:
 		ops->init		= r8156_init;
 		ops->enable		= rtl8156_enable;
-		ops->disable		= rtl8153_disable;
+		ops->disable		= rtl8156_disable;
 		ops->up			= rtl8156_up;
 		ops->down		= rtl8156_down;
 		ops->unload		= rtl8153_unload;
@@ -9442,9 +9508,8 @@
 	return 0;
 }
 
-u8 rtl8152_get_version(struct usb_interface *intf)
+static u8 __rtl_get_hw_ver(struct usb_device *udev)
 {
-	struct usb_device *udev = interface_to_usbdev(intf);
 	u32 ocp_data = 0;
 	__le32 *tmp;
 	u8 version;
@@ -9456,7 +9521,8 @@
 
 	ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 			      RTL8152_REQ_GET_REGS, RTL8152_REQT_READ,
-			      PLA_TCR0, MCU_TYPE_PLA, tmp, sizeof(*tmp), 500);
+			      PLA_TCR0, MCU_TYPE_PLA, tmp, sizeof(*tmp),
+			      USB_CTRL_GET_TIMEOUT);
 	if (ret > 0)
 		ocp_data = (__le32_to_cpu(*tmp) >> 16) & VERSION_MASK;
 
@@ -9513,10 +9579,19 @@
 		break;
 	default:
 		version = RTL_VER_UNKNOWN;
-		dev_info(&intf->dev, "Unknown version 0x%04x\n", ocp_data);
+		dev_info(&udev->dev, "Unknown version 0x%04x\n", ocp_data);
 		break;
 	}
 
+	return version;
+}
+
+u8 rtl8152_get_version(struct usb_interface *intf)
+{
+	u8 version;
+
+	version = __rtl_get_hw_ver(interface_to_usbdev(intf));
+
 	dev_dbg(&intf->dev, "Detected version 0x%04x\n", version);
 
 	return version;
@@ -9535,7 +9610,10 @@
 	if (version == RTL_VER_UNKNOWN)
 		return -ENODEV;
 
-	if (!rtl_vendor_mode(intf))
+	if (intf->cur_altsetting->desc.bInterfaceClass != USB_CLASS_VENDOR_SPEC)
+		return -ENODEV;
+
+	if (!rtl_check_vendor_ok(intf))
 		return -ENODEV;
 
 	usb_reset_device(udev);
@@ -9605,6 +9683,7 @@
 
 	if (le16_to_cpu(udev->descriptor.idVendor) == VENDOR_ID_LENOVO) {
 		switch (le16_to_cpu(udev->descriptor.idProduct)) {
+		case DEVICE_ID_THINKPAD_ONELINK_PLUS_DOCK:
 		case DEVICE_ID_THINKPAD_THUNDERBOLT3_DOCK_GEN2:
 		case DEVICE_ID_THINKPAD_USB_C_DOCK_GEN2:
 			tp->lenovo_macpassthru = 1;
@@ -9715,6 +9794,10 @@
 
 out1:
 	tasklet_kill(&tp->tx_tl);
+	cancel_delayed_work_sync(&tp->hw_phy_work);
+	if (tp->rtl_ops.unload)
+		tp->rtl_ops.unload(tp);
+	rtl8152_release_firmware(tp);
 	usb_set_intfdata(intf, NULL);
 out:
 	free_netdev(netdev);
@@ -9739,41 +9822,38 @@
 	}
 }
 
-#define REALTEK_USB_DEVICE(vend, prod)	{ \
-	USB_DEVICE_INTERFACE_CLASS(vend, prod, USB_CLASS_VENDOR_SPEC), \
-}, \
-{ \
-	USB_DEVICE_AND_INTERFACE_INFO(vend, prod, USB_CLASS_COMM, \
-			USB_CDC_SUBCLASS_ETHERNET, USB_CDC_PROTO_NONE), \
-}
-
 /* table of devices that work with this driver */
 static const struct usb_device_id rtl8152_table[] = {
 	/* Realtek */
-	REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8050),
-	REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8053),
-	REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8152),
-	REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8153),
-	REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8155),
-	REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8156),
+	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x8050) },
+	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x8053) },
+	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x8152) },
+	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x8153) },
+	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x8155) },
+	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x8156) },
 
 	/* Microsoft */
-	REALTEK_USB_DEVICE(VENDOR_ID_MICROSOFT, 0x07ab),
-	REALTEK_USB_DEVICE(VENDOR_ID_MICROSOFT, 0x07c6),
-	REALTEK_USB_DEVICE(VENDOR_ID_MICROSOFT, 0x0927),
-	REALTEK_USB_DEVICE(VENDOR_ID_SAMSUNG, 0xa101),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x304f),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x3062),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x3069),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x3082),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x7205),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x720c),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x7214),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0x721e),
-	REALTEK_USB_DEVICE(VENDOR_ID_LENOVO,  0xa387),
-	REALTEK_USB_DEVICE(VENDOR_ID_LINKSYS, 0x0041),
-	REALTEK_USB_DEVICE(VENDOR_ID_NVIDIA,  0x09ff),
-	REALTEK_USB_DEVICE(VENDOR_ID_TPLINK,  0x0601),
+	{ USB_DEVICE(VENDOR_ID_MICROSOFT, 0x07ab) },
+	{ USB_DEVICE(VENDOR_ID_MICROSOFT, 0x07c6) },
+	{ USB_DEVICE(VENDOR_ID_MICROSOFT, 0x0927) },
+	{ USB_DEVICE(VENDOR_ID_MICROSOFT, 0x0c5e) },
+	{ USB_DEVICE(VENDOR_ID_SAMSUNG, 0xa101) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x304f) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x3054) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x3062) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x3069) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x3082) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x3098) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x7205) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x720c) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x7214) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0x721e) },
+	{ USB_DEVICE(VENDOR_ID_LENOVO,  0xa387) },
+	{ USB_DEVICE(VENDOR_ID_LINKSYS, 0x0041) },
+	{ USB_DEVICE(VENDOR_ID_NVIDIA,  0x09ff) },
+	{ USB_DEVICE(VENDOR_ID_TPLINK,  0x0601) },
+	{ USB_DEVICE(VENDOR_ID_DLINK,   0xb301) },
+	{ USB_DEVICE(VENDOR_ID_ASUS,    0x1976) },
 	{}
 };
 
@@ -9793,7 +9873,68 @@
 	.disable_hub_initiated_lpm = 1,
 };
 
-module_usb_driver(rtl8152_driver);
+static int rtl8152_cfgselector_probe(struct usb_device *udev)
+{
+	struct usb_host_config *c;
+	int i, num_configs;
+
+	/* Switch the device to vendor mode, if and only if the vendor mode
+	 * driver supports it.
+	 */
+	if (__rtl_get_hw_ver(udev) == RTL_VER_UNKNOWN)
+		return 0;
+
+	/* The vendor mode is not always config #1, so to find it out. */
+	c = udev->config;
+	num_configs = udev->descriptor.bNumConfigurations;
+	for (i = 0; i < num_configs; (i++, c++)) {
+		struct usb_interface_descriptor	*desc = NULL;
+
+		if (!c->desc.bNumInterfaces)
+			continue;
+		desc = &c->intf_cache[0]->altsetting->desc;
+		if (desc->bInterfaceClass == USB_CLASS_VENDOR_SPEC)
+			break;
+	}
+
+	if (i == num_configs)
+		return -ENODEV;
+
+	if (usb_set_configuration(udev, c->desc.bConfigurationValue)) {
+		dev_err(&udev->dev, "Failed to set configuration %d\n",
+			c->desc.bConfigurationValue);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static struct usb_device_driver rtl8152_cfgselector_driver = {
+	.name =		MODULENAME "-cfgselector",
+	.probe =	rtl8152_cfgselector_probe,
+	.id_table =	rtl8152_table,
+	.generic_subclass = 1,
+	.supports_autosuspend = 1,
+};
+
+static int __init rtl8152_driver_init(void)
+{
+	int ret;
+
+	ret = usb_register_device_driver(&rtl8152_cfgselector_driver, THIS_MODULE);
+	if (ret)
+		return ret;
+	return usb_register(&rtl8152_driver);
+}
+
+static void __exit rtl8152_driver_exit(void)
+{
+	usb_deregister(&rtl8152_driver);
+	usb_deregister_device_driver(&rtl8152_cfgselector_driver);
+}
+
+module_init(rtl8152_driver_init);
+module_exit(rtl8152_driver_exit);
 
 MODULE_AUTHOR(DRIVER_AUTHOR);
 MODULE_DESCRIPTION(DRIVER_DESC);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/rndis_host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/rndis_host.c
@@ -255,7 +255,8 @@
 
 	off = le32_to_cpu(u.get_c->offset);
 	len = le32_to_cpu(u.get_c->len);
-	if (unlikely((8 + off + len) > CONTROL_BUFFER_SIZE))
+	if (unlikely((off > CONTROL_BUFFER_SIZE - 8) ||
+		     (len > CONTROL_BUFFER_SIZE - 8 - off)))
 		goto response_error;
 
 	if (*reply_len != -1 && len != *reply_len)
@@ -609,6 +610,11 @@
 				      USB_CLASS_COMM, 2 /* ACM */, 0x0ff),
 	.driver_info = (unsigned long) &rndis_poll_status_info,
 }, {
+	/* Hytera Communications DMR radios' "Radio to PC Network" */
+	USB_VENDOR_AND_INTERFACE_INFO(0x238b,
+				      USB_CLASS_COMM, 2 /* ACM */, 0x0ff),
+	.driver_info = (unsigned long)&rndis_info,
+}, {
 	/* RNDIS is MSFT's un-official variant of CDC ACM */
 	USB_INTERFACE_INFO(USB_CLASS_COMM, 2 /* ACM */, 0x0ff),
 	.driver_info = (unsigned long) &rndis_info,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/rtl8150.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/rtl8150.c
@@ -71,6 +71,14 @@
 #define MSR_SPEED		(1<<3)
 #define MSR_LINK		(1<<2)
 
+/* USB endpoints */
+enum rtl8150_usb_ep {
+	RTL8150_USB_EP_CONTROL = 0,
+	RTL8150_USB_EP_BULK_IN = 1,
+	RTL8150_USB_EP_BULK_OUT = 2,
+	RTL8150_USB_EP_INT_IN = 3,
+};
+
 /* Interrupt pipe data */
 #define INT_TSR			0x00
 #define INT_RSR			0x01
@@ -778,7 +786,8 @@
 				      struct ethtool_link_ksettings *ecmd)
 {
 	rtl8150_t *dev = netdev_priv(netdev);
-	short lpa, bmcr;
+	short lpa = 0;
+	short bmcr = 0;
 	u32 supported;
 
 	supported = (SUPPORTED_10baseT_Half |
@@ -866,6 +875,13 @@
 	struct usb_device *udev = interface_to_usbdev(intf);
 	rtl8150_t *dev;
 	struct net_device *netdev;
+	static const u8 bulk_ep_addr[] = {
+		RTL8150_USB_EP_BULK_IN | USB_DIR_IN,
+		RTL8150_USB_EP_BULK_OUT | USB_DIR_OUT,
+		0};
+	static const u8 int_ep_addr[] = {
+		RTL8150_USB_EP_INT_IN | USB_DIR_IN,
+		0};
 
 	netdev = alloc_etherdev(sizeof(rtl8150_t));
 	if (!netdev)
@@ -879,6 +895,13 @@
 		return -ENOMEM;
 	}
 
+	/* Verify that all required endpoints are present */
+	if (!usb_check_bulk_endpoints(intf, bulk_ep_addr) ||
+	    !usb_check_int_endpoints(intf, int_ep_addr)) {
+		dev_err(&intf->dev, "couldn't find required endpoints\n");
+		goto out;
+	}
+
 	tasklet_setup(&dev->tl, rx_fixup);
 	spin_lock_init(&dev->rx_pool_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/sierra_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/sierra_net.c
@@ -669,6 +669,7 @@
 		0x00, 0x00, SIERRA_NET_HIP_MSYNC_ID, 0x00};
 	static const u8 shdwn_tmplate[sizeof(priv->shdwn_msg)] = {
 		0x00, 0x00, SIERRA_NET_HIP_SHUTD_ID, 0x00};
+	u8 mod[2];
 
 	dev_dbg(&dev->udev->dev, "%s", __func__);
 
@@ -698,8 +699,9 @@
 	dev->net->netdev_ops = &sierra_net_device_ops;
 
 	/* change MAC addr to include, ifacenum, and to be unique */
-	dev->net->dev_addr[ETH_ALEN-2] = atomic_inc_return(&iface_counter);
-	dev->net->dev_addr[ETH_ALEN-1] = ifacenum;
+	mod[0] = atomic_inc_return(&iface_counter);
+	mod[1] = ifacenum;
+	dev_addr_mod(dev->net, ETH_ALEN - 2, mod, 2);
 
 	/* prepare shutdown message template */
 	memcpy(priv->shdwn_msg, shdwn_tmplate, sizeof(priv->shdwn_msg));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/smsc75xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/smsc75xx.c
@@ -90,7 +90,9 @@
 	ret = fn(dev, USB_VENDOR_REQUEST_READ_REGISTER, USB_DIR_IN
 		 | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 0, index, &buf, 4);
-	if (unlikely(ret < 0)) {
+	if (unlikely(ret < 4)) {
+		ret = ret < 0 ? ret : -ENODATA;
+
 		netdev_warn(dev->net, "Failed to read reg index 0x%08x: %d\n",
 			    index, ret);
 		return ret;
@@ -2199,6 +2201,13 @@
 		size = (rx_cmd_a & RX_CMD_A_LEN) - RXW_PADDING;
 		align_count = (4 - ((size + RXW_PADDING) % 4)) % 4;
 
+		if (unlikely(size > skb->len)) {
+			netif_dbg(dev, rx_err, dev->net,
+				  "size err rx_cmd_a=0x%08x\n",
+				  rx_cmd_a);
+			return 0;
+		}
+
 		if (unlikely(rx_cmd_a & RX_CMD_A_RED)) {
 			netif_dbg(dev, rx_err, dev->net,
 				  "Error rx_cmd_a=0x%08x\n", rx_cmd_a);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/smsc95xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/smsc95xx.c
@@ -84,9 +84,12 @@
 	ret = fn(dev, USB_VENDOR_REQUEST_READ_REGISTER, USB_DIR_IN
 		 | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 0, index, &buf, 4);
-	if (unlikely(ret < 0)) {
-		netdev_warn(dev->net, "Failed to read reg index 0x%08x: %d\n",
-			    index, ret);
+	if (ret < 4) {
+		ret = ret < 0 ? ret : -ENODATA;
+
+		if (ret != -ENODEV)
+			netdev_warn(dev->net, "Failed to read reg index 0x%08x: %d\n",
+				    index, ret);
 		return ret;
 	}
 
@@ -116,7 +119,7 @@
 	ret = fn(dev, USB_VENDOR_REQUEST_WRITE_REGISTER, USB_DIR_OUT
 		 | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 0, index, &buf, 4);
-	if (unlikely(ret < 0))
+	if (ret < 0 && ret != -ENODEV)
 		netdev_warn(dev->net, "Failed to write reg index 0x%08x: %d\n",
 			    index, ret);
 
@@ -159,6 +162,9 @@
 	do {
 		ret = __smsc95xx_read_reg(dev, MII_ADDR, &val, in_pm);
 		if (ret < 0) {
+			/* Ignore -ENODEV error during disconnect() */
+			if (ret == -ENODEV)
+				return 0;
 			netdev_warn(dev->net, "Error reading MII_ACCESS\n");
 			return ret;
 		}
@@ -194,7 +200,8 @@
 	addr = mii_address_cmd(phy_id, idx, MII_READ_ | MII_BUSY_);
 	ret = __smsc95xx_write_reg(dev, MII_ADDR, addr, in_pm);
 	if (ret < 0) {
-		netdev_warn(dev->net, "Error writing MII_ADDR\n");
+		if (ret != -ENODEV)
+			netdev_warn(dev->net, "Error writing MII_ADDR\n");
 		goto done;
 	}
 
@@ -206,7 +213,8 @@
 
 	ret = __smsc95xx_read_reg(dev, MII_DATA, &val, in_pm);
 	if (ret < 0) {
-		netdev_warn(dev->net, "Error reading MII_DATA\n");
+		if (ret != -ENODEV)
+			netdev_warn(dev->net, "Error reading MII_DATA\n");
 		goto done;
 	}
 
@@ -214,6 +222,10 @@
 
 done:
 	mutex_unlock(&dev->phy_mutex);
+
+	/* Ignore -ENODEV error during disconnect() */
+	if (ret == -ENODEV)
+		return 0;
 	return ret;
 }
 
@@ -235,7 +247,8 @@
 	val = regval;
 	ret = __smsc95xx_write_reg(dev, MII_DATA, val, in_pm);
 	if (ret < 0) {
-		netdev_warn(dev->net, "Error writing MII_DATA\n");
+		if (ret != -ENODEV)
+			netdev_warn(dev->net, "Error writing MII_DATA\n");
 		goto done;
 	}
 
@@ -243,7 +256,8 @@
 	addr = mii_address_cmd(phy_id, idx, MII_WRITE_ | MII_BUSY_);
 	ret = __smsc95xx_write_reg(dev, MII_ADDR, addr, in_pm);
 	if (ret < 0) {
-		netdev_warn(dev->net, "Error writing MII_ADDR\n");
+		if (ret != -ENODEV)
+			netdev_warn(dev->net, "Error writing MII_ADDR\n");
 		goto done;
 	}
 
@@ -552,16 +566,12 @@
 	return smsc95xx_write_reg(dev, AFC_CFG, afc_cfg);
 }
 
-static int smsc95xx_link_reset(struct usbnet *dev)
+static void smsc95xx_mac_update_fullduplex(struct usbnet *dev)
 {
 	struct smsc95xx_priv *pdata = dev->driver_priv;
 	unsigned long flags;
 	int ret;
 
-	ret = smsc95xx_write_reg(dev, INT_STS, INT_STS_CLEAR_ALL_);
-	if (ret < 0)
-		return ret;
-
 	spin_lock_irqsave(&pdata->mac_cr_lock, flags);
 	if (pdata->phydev->duplex != DUPLEX_FULL) {
 		pdata->mac_cr &= ~MAC_CR_FDPX_;
@@ -573,14 +583,16 @@
 	spin_unlock_irqrestore(&pdata->mac_cr_lock, flags);
 
 	ret = smsc95xx_write_reg(dev, MAC_CR, pdata->mac_cr);
-	if (ret < 0)
-		return ret;
+	if (ret < 0) {
+		if (ret != -ENODEV)
+			netdev_warn(dev->net,
+				    "Error updating MAC full duplex mode\n");
+		return;
+	}
 
 	ret = smsc95xx_phy_update_flowcontrol(dev);
 	if (ret < 0)
 		netdev_warn(dev->net, "Error updating PHY flow control\n");
-
-	return ret;
 }
 
 static void smsc95xx_status(struct usbnet *dev, struct urb *urb)
@@ -597,7 +609,7 @@
 	netif_dbg(dev, link, dev->net, "intdata: 0x%08X\n", intdata);
 
 	if (intdata & INT_ENP_PHY_INT_)
-		usbnet_defer_kevent(dev, EVENT_LINK_RESET);
+		;
 	else
 		netdev_warn(dev->net, "unexpected interrupt, intdata=0x%08X\n",
 			    intdata);
@@ -830,7 +842,7 @@
 static int smsc95xx_reset(struct usbnet *dev)
 {
 	struct smsc95xx_priv *pdata = dev->driver_priv;
-	u32 read_buf, write_buf, burst_cap;
+	u32 read_buf, burst_cap;
 	int ret = 0, timeout;
 
 	netif_dbg(dev, ifup, dev->net, "entering smsc95xx_reset\n");
@@ -850,7 +862,7 @@
 
 	if (timeout >= 100) {
 		netdev_warn(dev->net, "timeout waiting for completion of Lite Reset\n");
-		return ret;
+		return -ETIMEDOUT;
 	}
 
 	ret = smsc95xx_write_reg(dev, PM_CTRL, PM_CTL_PHY_RST_);
@@ -972,10 +984,13 @@
 		return ret;
 	netif_dbg(dev, ifup, dev->net, "ID_REV = 0x%08x\n", read_buf);
 
+	ret = smsc95xx_read_reg(dev, LED_GPIO_CFG, &read_buf);
+	if (ret < 0)
+		return ret;
 	/* Configure GPIO pins as LED outputs */
-	write_buf = LED_GPIO_CFG_SPD_LED | LED_GPIO_CFG_LNK_LED |
-		LED_GPIO_CFG_FDX_LED;
-	ret = smsc95xx_write_reg(dev, LED_GPIO_CFG, write_buf);
+	read_buf |= LED_GPIO_CFG_SPD_LED | LED_GPIO_CFG_LNK_LED |
+		    LED_GPIO_CFG_FDX_LED;
+	ret = smsc95xx_write_reg(dev, LED_GPIO_CFG, read_buf);
 	if (ret < 0)
 		return ret;
 
@@ -1049,6 +1064,15 @@
 	.ndo_set_features	= smsc95xx_set_features,
 };
 
+static void smsc95xx_handle_link_change(struct net_device *net)
+{
+	struct usbnet *dev = netdev_priv(net);
+
+	phy_print_status(net->phydev);
+	smsc95xx_mac_update_fullduplex(dev);
+	usbnet_defer_kevent(dev, EVENT_LINK_CHANGE);
+}
+
 static int smsc95xx_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	struct smsc95xx_priv *pdata;
@@ -1153,6 +1177,17 @@
 	dev->net->min_mtu = ETH_MIN_MTU;
 	dev->net->max_mtu = ETH_DATA_LEN;
 	dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len;
+
+	ret = phy_connect_direct(dev->net, pdata->phydev,
+				 &smsc95xx_handle_link_change,
+				 PHY_INTERFACE_MODE_MII);
+	if (ret) {
+		netdev_err(dev->net, "can't attach PHY to %s\n", pdata->mdiobus->id);
+		goto unregister_mdio;
+	}
+
+	phy_attached_info(dev->net->phydev);
+
 	return 0;
 
 unregister_mdio:
@@ -1170,47 +1205,24 @@
 {
 	struct smsc95xx_priv *pdata = dev->driver_priv;
 
+	phy_disconnect(dev->net->phydev);
 	mdiobus_unregister(pdata->mdiobus);
 	mdiobus_free(pdata->mdiobus);
 	netif_dbg(dev, ifdown, dev->net, "free pdata\n");
 	kfree(pdata);
 }
 
-static void smsc95xx_handle_link_change(struct net_device *net)
-{
-	struct usbnet *dev = netdev_priv(net);
-
-	phy_print_status(net->phydev);
-	usbnet_defer_kevent(dev, EVENT_LINK_CHANGE);
-}
-
 static int smsc95xx_start_phy(struct usbnet *dev)
 {
-	struct smsc95xx_priv *pdata = dev->driver_priv;
-	struct net_device *net = dev->net;
-	int ret;
+	phy_start(dev->net->phydev);
 
-	ret = smsc95xx_reset(dev);
-	if (ret < 0)
-		return ret;
-
-	ret = phy_connect_direct(net, pdata->phydev,
-				 &smsc95xx_handle_link_change,
-				 PHY_INTERFACE_MODE_MII);
-	if (ret) {
-		netdev_err(net, "can't attach PHY to %s\n", pdata->mdiobus->id);
-		return ret;
-	}
-
-	phy_attached_info(net->phydev);
-	phy_start(net->phydev);
 	return 0;
 }
 
-static int smsc95xx_disconnect_phy(struct usbnet *dev)
+static int smsc95xx_stop(struct usbnet *dev)
 {
 	phy_stop(dev->net->phydev);
-	phy_disconnect(dev->net->phydev);
+
 	return 0;
 }
 
@@ -1776,9 +1788,11 @@
 
 static void smsc95xx_rx_csum_offload(struct sk_buff *skb)
 {
-	skb->csum = *(u16 *)(skb_tail_pointer(skb) - 2);
+	u16 *csum_ptr = (u16 *)(skb_tail_pointer(skb) - 2);
+
+	skb->csum = (__force __wsum)get_unaligned(csum_ptr);
 	skb->ip_summed = CHECKSUM_COMPLETE;
-	skb_trim(skb, skb->len - 2);
+	skb_trim(skb, skb->len - 2); /* remove csum */
 }
 
 static int smsc95xx_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
@@ -1801,6 +1815,12 @@
 		size = (u16)((header & RX_STS_FL_) >> 16);
 		align_count = (4 - ((size + NET_IP_ALIGN) % 4)) % 4;
 
+		if (unlikely(size > skb->len)) {
+			netif_dbg(dev, rx_err, dev->net,
+				  "size err header=0x%08x\n", header);
+			return 0;
+		}
+
 		if (unlikely(header & RX_STS_ES_)) {
 			netif_dbg(dev, rx_err, dev->net,
 				  "Error header=0x%08x\n", header);
@@ -1830,25 +1850,22 @@
 				if (dev->net->features & NETIF_F_RXCSUM)
 					smsc95xx_rx_csum_offload(skb);
 				skb_trim(skb, skb->len - 4); /* remove fcs */
-				skb->truesize = size + sizeof(struct sk_buff);
 
 				return 1;
 			}
 
-			ax_skb = skb_clone(skb, GFP_ATOMIC);
+			ax_skb = netdev_alloc_skb_ip_align(dev->net, size);
 			if (unlikely(!ax_skb)) {
 				netdev_warn(dev->net, "Error allocating skb\n");
 				return 0;
 			}
 
-			ax_skb->len = size;
-			ax_skb->data = packet;
-			skb_set_tail_pointer(ax_skb, size);
+			skb_put(ax_skb, size);
+			memcpy(ax_skb->data, packet, size);
 
 			if (dev->net->features & NETIF_F_RXCSUM)
 				smsc95xx_rx_csum_offload(ax_skb);
 			skb_trim(ax_skb, ax_skb->len - 4); /* remove fcs */
-			ax_skb->truesize = size + sizeof(struct sk_buff);
 
 			usbnet_skb_return(dev, ax_skb);
 		}
@@ -1963,9 +1980,9 @@
 	.description	= "smsc95xx USB 2.0 Ethernet",
 	.bind		= smsc95xx_bind,
 	.unbind		= smsc95xx_unbind,
-	.link_reset	= smsc95xx_link_reset,
-	.reset		= smsc95xx_start_phy,
-	.stop		= smsc95xx_disconnect_phy,
+	.reset		= smsc95xx_reset,
+	.check_connect	= smsc95xx_start_phy,
+	.stop		= smsc95xx_stop,
 	.rx_fixup	= smsc95xx_rx_fixup,
 	.tx_fixup	= smsc95xx_tx_fixup,
 	.status		= smsc95xx_status,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/sr9700.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/sr9700.c
@@ -56,7 +56,8 @@
 				value, reg, NULL, 0);
 }
 
-static void sr_write_async(struct usbnet *dev, u8 reg, u16 length, void *data)
+static void sr_write_async(struct usbnet *dev, u8 reg, u16 length,
+			   const void *data)
 {
 	usbnet_write_cmd_async(dev, SR_WR_REGS, SR_REQ_WR_REG,
 			       0, reg, data, length);
@@ -178,6 +179,7 @@
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res;
 	int rc = 0;
+	int err;
 
 	if (phy_id) {
 		netdev_dbg(netdev, "Only internal phy supported\n");
@@ -188,11 +190,17 @@
 	if (loc == MII_BMSR) {
 		u8 value;
 
-		sr_read_reg(dev, SR_NSR, &value);
+		err = sr_read_reg(dev, SR_NSR, &value);
+		if (err < 0)
+			return err;
+
 		if (value & NSR_LINKST)
 			rc = 1;
 	}
-	sr_share_read_word(dev, 1, loc, &res);
+	err = sr_share_read_word(dev, 1, loc, &res);
+	if (err < 0)
+		return err;
+
 	if (rc == 1)
 		res = le16_to_cpu(res) | BMSR_LSTATUS;
 	else
@@ -319,6 +327,7 @@
 {
 	struct net_device *netdev;
 	struct mii_if_info *mii;
+	u8 addr[ETH_ALEN];
 	int ret;
 
 	ret = usbnet_get_endpoints(dev, intf);
@@ -349,11 +358,12 @@
 	 * EEPROM automatically to PAR. In case there is no EEPROM externally,
 	 * a default MAC address is stored in PAR for making chip work properly.
 	 */
-	if (sr_read(dev, SR_PAR, ETH_ALEN, netdev->dev_addr) < 0) {
+	if (sr_read(dev, SR_PAR, ETH_ALEN, addr) < 0) {
 		netdev_err(netdev, "Error reading MAC address\n");
 		ret = -ENODEV;
 		goto out;
 	}
+	eth_hw_addr_set(netdev, addr);
 
 	/* power up and reset phy */
 	sr_write_reg(dev, SR_PRR, PRR_PHY_RST);
@@ -410,7 +420,7 @@
 		/* ignore the CRC length */
 		len = (skb->data[1] | (skb->data[2] << 8)) - 4;
 
-		if (len > ETH_FRAME_LEN)
+		if (len > ETH_FRAME_LEN || len > skb->len || len < 0)
 			return 0;
 
 		/* the last packet of current skb */
@@ -418,19 +428,15 @@
 			skb_pull(skb, 3);
 			skb->len = len;
 			skb_set_tail_pointer(skb, len);
-			skb->truesize = len + sizeof(struct sk_buff);
 			return 2;
 		}
 
-		/* skb_clone is used for address align */
-		sr_skb = skb_clone(skb, GFP_ATOMIC);
+		sr_skb = netdev_alloc_skb_ip_align(dev->net, len);
 		if (!sr_skb)
 			return 0;
 
-		sr_skb->len = len;
-		sr_skb->data = skb->data + 3;
-		skb_set_tail_pointer(sr_skb, len);
-		sr_skb->truesize = len + sizeof(struct sk_buff);
+		skb_put(sr_skb, len);
+		memcpy(sr_skb->data, skb->data + 3, len);
 		usbnet_skb_return(dev, sr_skb);
 
 		skb_pull(skb, len + SR_RX_OVERHEAD);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/sr9800.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/sr9800.c
@@ -731,12 +731,15 @@
 	struct sr_data *data = (struct sr_data *)&dev->data;
 	u16 led01_mux, led23_mux;
 	int ret, embd_phy;
+	u8 addr[ETH_ALEN];
 	u32 phyid;
 	u16 rx_ctl;
 
 	data->eeprom_len = SR9800_EEPROM_LEN;
 
-	usbnet_get_endpoints(dev, intf);
+	ret = usbnet_get_endpoints(dev, intf);
+	if (ret)
+		goto out;
 
 	/* LED Setting Rule :
 	 * AABB:CCDD
@@ -754,12 +757,12 @@
 	}
 
 	/* Get the MAC address */
-	ret = sr_read_cmd(dev, SR_CMD_READ_NODE_ID, 0, 0, ETH_ALEN,
-			  dev->net->dev_addr);
+	ret = sr_read_cmd(dev, SR_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, addr);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret);
 		return ret;
 	}
+	eth_hw_addr_set(dev->net, addr);
 	netdev_dbg(dev->net, "mac addr : %pM\n", dev->net->dev_addr);
 
 	/* Initialize MII structure */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/usbnet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/usbnet.c
@@ -64,9 +64,6 @@
 
 /*-------------------------------------------------------------------------*/
 
-// randomly generated ethernet address
-static u8	node_id [ETH_ALEN];
-
 /* use ethtool to change the level for any given device */
 static int msg_level = -1;
 module_param (msg_level, int, 0);
@@ -165,12 +162,13 @@
 
 int usbnet_get_ethernet_addr(struct usbnet *dev, int iMACAddress)
 {
+	u8		addr[ETH_ALEN];
 	int 		tmp = -1, ret;
 	unsigned char	buf [13];
 
 	ret = usb_string(dev->udev, iMACAddress, buf, sizeof buf);
 	if (ret == 12)
-		tmp = hex2bin(dev->net->dev_addr, buf, 6);
+		tmp = hex2bin(addr, buf, 6);
 	if (tmp < 0) {
 		dev_dbg(&dev->udev->dev,
 			"bad MAC string %d fetch, %d\n", iMACAddress, tmp);
@@ -178,10 +176,22 @@
 			ret = -EINVAL;
 		return ret;
 	}
+	eth_hw_addr_set(dev->net, addr);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(usbnet_get_ethernet_addr);
 
+static bool usbnet_needs_usb_name_format(struct usbnet *dev, struct net_device *net)
+{
+	/* Point to point devices which don't have a real MAC address
+	 * (or report a fake local one) have historically used the usb%d
+	 * naming. Preserve this..
+	 */
+	return (dev->driver_info->flags & FLAG_POINTTOPOINT) != 0 &&
+		(is_zero_ether_addr(net->dev_addr) ||
+		 is_local_ether_addr(net->dev_addr));
+}
+
 static void intr_complete (struct urb *urb)
 {
 	struct usbnet	*dev = urb->context;
@@ -468,10 +478,15 @@
 void usbnet_defer_kevent (struct usbnet *dev, int work)
 {
 	set_bit (work, &dev->flags);
-	if (!schedule_work (&dev->kevent))
-		netdev_dbg(dev->net, "kevent %s may have been dropped\n", usbnet_event_names[work]);
-	else
-		netdev_dbg(dev->net, "kevent %s scheduled\n", usbnet_event_names[work]);
+	if (!usbnet_going_away(dev)) {
+		if (!schedule_work(&dev->kevent))
+			netdev_dbg(dev->net,
+				   "kevent %s may have been dropped\n",
+				   usbnet_event_names[work]);
+		else
+			netdev_dbg(dev->net,
+				   "kevent %s scheduled\n", usbnet_event_names[work]);
+	}
 }
 EXPORT_SYMBOL_GPL(usbnet_defer_kevent);
 
@@ -518,7 +533,8 @@
 	    netif_device_present (dev->net) &&
 	    test_bit(EVENT_DEV_OPEN, &dev->flags) &&
 	    !test_bit (EVENT_RX_HALT, &dev->flags) &&
-	    !test_bit (EVENT_DEV_ASLEEP, &dev->flags)) {
+	    !test_bit (EVENT_DEV_ASLEEP, &dev->flags) &&
+	    !usbnet_going_away(dev)) {
 		switch (retval = usb_submit_urb (urb, GFP_ATOMIC)) {
 		case -EPIPE:
 			usbnet_defer_kevent (dev, EVENT_RX_HALT);
@@ -847,13 +863,20 @@
 
 	mpn = !test_and_clear_bit(EVENT_NO_RUNTIME_PM, &dev->flags);
 
-	/* deferred work (task, timer, softirq) must also stop.
-	 * can't flush_scheduled_work() until we drop rtnl (later),
-	 * else workers could deadlock; so make workers a NOP.
-	 */
+	/* deferred work (timer, softirq, task) must also stop */
 	dev->flags = 0;
-	del_timer_sync (&dev->delay);
-	tasklet_kill (&dev->bh);
+	del_timer_sync(&dev->delay);
+	tasklet_kill(&dev->bh);
+	cancel_work_sync(&dev->kevent);
+
+	/* We have cyclic dependencies. Those calls are needed
+	 * to break a cycle. We cannot fall into the gaps because
+	 * we have a flag
+	 */
+	tasklet_kill(&dev->bh);
+	del_timer_sync(&dev->delay);
+	cancel_work_sync(&dev->kevent);
+
 	if (!pm)
 		usb_autopm_put_interface(dev->intf);
 
@@ -1179,7 +1202,8 @@
 					   status);
 		} else {
 			clear_bit (EVENT_RX_HALT, &dev->flags);
-			tasklet_schedule (&dev->bh);
+			if (!usbnet_going_away(dev))
+				tasklet_schedule(&dev->bh);
 		}
 	}
 
@@ -1204,7 +1228,8 @@
 			usb_autopm_put_interface(dev->intf);
 fail_lowmem:
 			if (resched)
-				tasklet_schedule (&dev->bh);
+				if (!usbnet_going_away(dev))
+					tasklet_schedule(&dev->bh);
 		}
 	}
 
@@ -1560,6 +1585,7 @@
 	} else if (netif_running (dev->net) &&
 		   netif_device_present (dev->net) &&
 		   netif_carrier_ok(dev->net) &&
+		   !usbnet_going_away(dev) &&
 		   !timer_pending(&dev->delay) &&
 		   !test_bit(EVENT_RX_PAUSED, &dev->flags) &&
 		   !test_bit(EVENT_RX_HALT, &dev->flags)) {
@@ -1601,11 +1627,13 @@
 	struct usbnet		*dev;
 	struct usb_device	*xdev;
 	struct net_device	*net;
+	struct urb		*urb;
 
 	dev = usb_get_intfdata(intf);
 	usb_set_intfdata(intf, NULL);
 	if (!dev)
 		return;
+	usbnet_mark_going_away(dev);
 
 	xdev = interface_to_usbdev (intf);
 
@@ -1614,15 +1642,17 @@
 		   xdev->bus->bus_name, xdev->devpath,
 		   dev->driver_info->description);
 
-	if (dev->driver_info->unbind)
-		dev->driver_info->unbind(dev, intf);
-
 	net = dev->net;
 	unregister_netdev (net);
 
-	cancel_work_sync(&dev->kevent);
+	while ((urb = usb_get_from_anchor(&dev->deferred))) {
+		dev_kfree_skb(urb->context);
+		kfree(urb->sg);
+		usb_free_urb(urb);
+	}
 
-	usb_scuttle_anchored_urbs(&dev->deferred);
+	if (dev->driver_info->unbind)
+		dev->driver_info->unbind(dev, intf);
 
 	usb_kill_urb(dev->interrupt);
 	usb_free_urb(dev->interrupt);
@@ -1726,7 +1756,6 @@
 
 	dev->net = net;
 	strscpy(net->name, "usb%d", sizeof(net->name));
-	memcpy (net->dev_addr, node_id, sizeof node_id);
 
 	/* rx and tx sides can use different message sizes;
 	 * bind() should set rx_urb_size in that case.
@@ -1746,12 +1775,11 @@
 		if (status < 0)
 			goto out1;
 
-		// heuristic:  "usb%d" for links we know are two-host,
-		// else "eth%d" when there's reasonable doubt.  userspace
-		// can rename the link if it knows better.
+		/* heuristic: rename to "eth%d" if we are not sure this link
+		 * is two-host (these links keep "usb%d")
+		 */
 		if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
-		    ((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
-		     (net->dev_addr [0] & 0x02) == 0))
+		    !usbnet_needs_usb_name_format(dev, net))
 			strscpy(net->name, "eth%d", sizeof(net->name));
 		/* WLAN devices should always be named "wlan%d" */
 		if ((dev->driver_info->flags & FLAG_WLAN) != 0)
@@ -1770,6 +1798,10 @@
 	} else if (!info->in || !info->out)
 		status = usbnet_get_endpoints (dev, udev);
 	else {
+		u8 ep_addrs[3] = {
+			info->in + USB_DIR_IN, info->out + USB_DIR_OUT, 0
+		};
+
 		dev->in = usb_rcvbulkpipe (xdev, info->in);
 		dev->out = usb_sndbulkpipe (xdev, info->out);
 		if (!(info->flags & FLAG_NO_SETINT))
@@ -1779,6 +1811,8 @@
 		else
 			status = 0;
 
+		if (status == 0 && !usb_check_bulk_endpoints(udev, ep_addrs))
+			status = -EINVAL;
 	}
 	if (status >= 0 && dev->status)
 		status = init_status (dev, udev);
@@ -1794,9 +1828,9 @@
 		goto out4;
 	}
 
-	/* let userspace know we have a random address */
-	if (ether_addr_equal(net->dev_addr, node_id))
-		net->addr_assign_type = NET_ADDR_RANDOM;
+	/* this flags the device for user space */
+	if (!is_valid_ether_addr(net->dev_addr))
+		eth_hw_addr_random(net);
 
 	if ((dev->driver_info->flags & FLAG_WLAN) != 0)
 		SET_NETDEV_DEVTYPE(net, &wlan_type);
@@ -1848,6 +1882,7 @@
 	 * may trigger an error resubmitting itself and, worse,
 	 * schedule a timer. So we kill it all just in case.
 	 */
+	usbnet_mark_going_away(dev);
 	cancel_work_sync(&dev->kevent);
 	del_timer_sync(&dev->delay);
 	free_percpu(net->tstats);
@@ -2002,7 +2037,7 @@
 		   cmd, reqtype, value, index, size);
 
 	if (size) {
-		buf = kmalloc(size, GFP_KERNEL);
+		buf = kmalloc(size, GFP_NOIO);
 		if (!buf)
 			goto out;
 	}
@@ -2034,7 +2069,7 @@
 		   cmd, reqtype, value, index, size);
 
 	if (data) {
-		buf = kmemdup(data, size, GFP_KERNEL);
+		buf = kmemdup(data, size, GFP_NOIO);
 		if (!buf)
 			goto out;
 	} else {
@@ -2135,7 +2170,7 @@
 int usbnet_write_cmd_async(struct usbnet *dev, u8 cmd, u8 reqtype,
 			   u16 value, u16 index, const void *data, u16 size)
 {
-	struct usb_ctrlrequest *req = NULL;
+	struct usb_ctrlrequest *req;
 	struct urb *urb;
 	int err = -ENOMEM;
 	void *buf = NULL;
@@ -2153,7 +2188,7 @@
 		if (!buf) {
 			netdev_err(dev->net, "Error allocating buffer"
 				   " in %s!\n", __func__);
-			goto fail_free;
+			goto fail_free_urb;
 		}
 	}
 
@@ -2177,14 +2212,21 @@
 	if (err < 0) {
 		netdev_err(dev->net, "Error submitting the control"
 			   " message: status=%d\n", err);
-		goto fail_free;
+		goto fail_free_all;
 	}
 	return 0;
 
+fail_free_all:
+	kfree(req);
 fail_free_buf:
 	kfree(buf);
-fail_free:
-	kfree(req);
+	/*
+	 * avoid a double free
+	 * needed because the flag can be set only
+	 * after filling the URB
+	 */
+	urb->transfer_flags = 0;
+fail_free_urb:
 	usb_free_urb(urb);
 fail:
 	return err;
@@ -2199,7 +2241,6 @@
 	BUILD_BUG_ON(
 		sizeof_field(struct sk_buff, cb) < sizeof(struct skb_data));
 
-	eth_random_addr(node_id);
 	return 0;
 }
 module_init(usbnet_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/usb/zaurus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/usb/zaurus.c
@@ -256,6 +256,11 @@
 	.bInterfaceSubClass	= USB_CDC_SUBCLASS_ETHERNET, \
 	.bInterfaceProtocol	= USB_CDC_PROTO_NONE
 
+#define ZAURUS_FAKE_INTERFACE \
+	.bInterfaceClass	= USB_CLASS_COMM, \
+	.bInterfaceSubClass	= USB_CDC_SUBCLASS_MDLM, \
+	.bInterfaceProtocol	= USB_CDC_PROTO_NONE
+
 /* SA-1100 based Sharp Zaurus ("collie"), or compatible. */
 {
 	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
@@ -284,11 +289,25 @@
 	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
 			  | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor		= 0x04DD,
+	.idProduct		= 0x8005,	/* A-300 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info = (unsigned long)&bogus_mdlm_info,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			  | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
 	.idProduct		= 0x8006,	/* B-500/SL-5600 */
 	ZAURUS_MASTER_INTERFACE,
 	.driver_info = ZAURUS_PXA_INFO,
 }, {
 	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			  | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
+	.idProduct		= 0x8006,	/* B-500/SL-5600 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info = (unsigned long)&bogus_mdlm_info,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
 	          | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor		= 0x04DD,
 	.idProduct		= 0x8007,	/* C-700 */
@@ -296,6 +315,13 @@
 	.driver_info = ZAURUS_PXA_INFO,
 }, {
 	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			  | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
+	.idProduct		= 0x8007,	/* C-700 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info = (unsigned long)&bogus_mdlm_info,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
 		 | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor               = 0x04DD,
 	.idProduct              = 0x9031,	/* C-750 C-760 */
@@ -315,6 +341,13 @@
 	.driver_info = ZAURUS_PXA_INFO,
 }, {
 	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+			    | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor		= 0x04DD,
+	.idProduct		= 0x9032,	/* SL-6000 */
+	ZAURUS_FAKE_INTERFACE,
+	.driver_info = (unsigned long)&bogus_mdlm_info,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
 		 | USB_DEVICE_ID_MATCH_DEVICE,
 	.idVendor               = 0x04DD,
 	/* reported with some C860 units */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/veth.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/veth.c
@@ -272,9 +272,10 @@
 {
 	/* Write ptr_ring before reading rx_notify_masked */
 	smp_mb();
-	if (!rq->rx_notify_masked) {
-		rq->rx_notify_masked = true;
-		napi_schedule(&rq->xdp_napi);
+	if (!READ_ONCE(rq->rx_notify_masked) &&
+	    napi_schedule_prep(&rq->xdp_napi)) {
+		WRITE_ONCE(rq->rx_notify_masked, true);
+		__napi_schedule(&rq->xdp_napi);
 	}
 }
 
@@ -319,6 +320,7 @@
 {
 	struct veth_priv *rcv_priv, *priv = netdev_priv(dev);
 	struct veth_rq *rq = NULL;
+	int ret = NETDEV_TX_OK;
 	struct net_device *rcv;
 	int length = skb->len;
 	bool use_napi = false;
@@ -326,7 +328,7 @@
 
 	rcu_read_lock();
 	rcv = rcu_dereference(priv->peer);
-	if (unlikely(!rcv)) {
+	if (unlikely(!rcv) || !pskb_may_pull(skb, ETH_HLEN)) {
 		kfree_skb(skb);
 		goto drop;
 	}
@@ -342,7 +344,6 @@
 		 */
 		use_napi = rcu_access_pointer(rq->napi) &&
 			   veth_skb_is_eligible_for_gro(dev, rcv, skb);
-		skb_record_rx_queue(skb, rxq);
 	}
 
 	skb_tx_timestamp(skb);
@@ -352,6 +353,7 @@
 	} else {
 drop:
 		atomic64_inc(&priv->dropped);
+		ret = NET_XMIT_DROP;
 	}
 
 	if (use_napi)
@@ -359,7 +361,7 @@
 
 	rcu_read_unlock();
 
-	return NETDEV_TX_OK;
+	return ret;
 }
 
 static u64 veth_stats_tx(struct net_device *dev, u64 *packets, u64 *bytes)
@@ -879,8 +881,12 @@
 
 			stats->xdp_bytes += skb->len;
 			skb = veth_xdp_rcv_skb(rq, skb, bq, stats);
-			if (skb)
-				napi_gro_receive(&rq->xdp_napi, skb);
+			if (skb) {
+				if (skb_shared(skb) || skb_unclone(skb, GFP_ATOMIC))
+					netif_receive_skb(skb);
+				else
+					napi_gro_receive(&rq->xdp_napi, skb);
+			}
 		}
 		done++;
 	}
@@ -912,19 +918,22 @@
 	xdp_set_return_frame_no_direct();
 	done = veth_xdp_rcv(rq, budget, &bq, &stats);
 
+	if (stats.xdp_redirect > 0)
+		xdp_do_flush();
+
 	if (done < budget && napi_complete_done(napi, done)) {
 		/* Write rx_notify_masked before reading ptr_ring */
 		smp_store_mb(rq->rx_notify_masked, false);
 		if (unlikely(!__ptr_ring_empty(&rq->xdp_ring))) {
-			rq->rx_notify_masked = true;
-			napi_schedule(&rq->xdp_napi);
+			if (napi_schedule_prep(&rq->xdp_napi)) {
+				WRITE_ONCE(rq->rx_notify_masked, true);
+				__napi_schedule(&rq->xdp_napi);
+			}
 		}
 	}
 
 	if (stats.xdp_tx > 0)
 		veth_xdp_flush(rq, &bq);
-	if (stats.xdp_redirect > 0)
-		xdp_do_flush();
 	xdp_clear_return_frame_no_direct();
 
 	return done;
@@ -1070,14 +1079,6 @@
 				veth_disable_xdp_range(dev, 0, dev->real_num_rx_queues, true);
 				return err;
 			}
-
-			if (!veth_gro_requested(dev)) {
-				/* user-space did not require GRO, but adding XDP
-				 * is supposed to get GRO working
-				 */
-				dev->features |= NETIF_F_GRO;
-				netdev_features_change(dev);
-			}
 		}
 	}
 
@@ -1097,18 +1098,9 @@
 	for (i = 0; i < dev->real_num_rx_queues; i++)
 		rcu_assign_pointer(priv->rq[i].xdp_prog, NULL);
 
-	if (!netif_running(dev) || !veth_gro_requested(dev)) {
+	if (!netif_running(dev) || !veth_gro_requested(dev))
 		veth_napi_del(dev);
 
-		/* if user-space did not require GRO, since adding XDP
-		 * enabled it, clear it now
-		 */
-		if (!veth_gro_requested(dev) && netif_running(dev)) {
-			dev->features &= ~NETIF_F_GRO;
-			netdev_features_change(dev);
-		}
-	}
-
 	veth_disable_xdp_range(dev, 0, dev->real_num_rx_queues, false);
 }
 
@@ -1311,7 +1303,8 @@
 	struct veth_priv *priv = netdev_priv(dev);
 	int i;
 
-	priv->rq = kcalloc(dev->num_rx_queues, sizeof(*priv->rq), GFP_KERNEL);
+	priv->rq = kvcalloc(dev->num_rx_queues, sizeof(*priv->rq),
+			    GFP_KERNEL_ACCOUNT | __GFP_RETRY_MAYFAIL);
 	if (!priv->rq)
 		return -ENOMEM;
 
@@ -1327,7 +1320,7 @@
 {
 	struct veth_priv *priv = netdev_priv(dev);
 
-	kfree(priv->rq);
+	kvfree(priv->rq);
 }
 
 static int veth_dev_init(struct net_device *dev)
@@ -1395,8 +1388,6 @@
 		if (peer_priv->_xdp_prog)
 			features &= ~NETIF_F_GSO_SOFTWARE;
 	}
-	if (priv->_xdp_prog)
-		features |= NETIF_F_GRO;
 
 	return features;
 }
@@ -1647,10 +1638,7 @@
 
 		nla_peer = data[VETH_INFO_PEER];
 		ifmp = nla_data(nla_peer);
-		err = rtnl_nla_parse_ifla(peer_tb,
-					  nla_data(nla_peer) + sizeof(struct ifinfomsg),
-					  nla_len(nla_peer) - sizeof(struct ifinfomsg),
-					  NULL);
+		err = rtnl_nla_parse_ifinfomsg(peer_tb, nla_peer, extack);
 		if (err < 0)
 			return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/virtio_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/virtio_net.c
@@ -213,9 +213,15 @@
 	/* Packet virtio header size */
 	u8 hdr_len;
 
-	/* Work struct for refilling if we run low on memory. */
+	/* Work struct for delayed refilling if we run low on memory. */
 	struct delayed_work refill;
 
+	/* Is delayed refill enabled? */
+	bool refill_enabled;
+
+	/* The lock to synchronize the access to refill_enabled */
+	spinlock_t refill_lock;
+
 	/* Work struct for config space updates */
 	struct work_struct config_work;
 
@@ -319,6 +325,20 @@
 	return p;
 }
 
+static void enable_delayed_refill(struct virtnet_info *vi)
+{
+	spin_lock_bh(&vi->refill_lock);
+	vi->refill_enabled = true;
+	spin_unlock_bh(&vi->refill_lock);
+}
+
+static void disable_delayed_refill(struct virtnet_info *vi)
+{
+	spin_lock_bh(&vi->refill_lock);
+	vi->refill_enabled = false;
+	spin_unlock_bh(&vi->refill_lock);
+}
+
 static void virtqueue_napi_schedule(struct napi_struct *napi,
 				    struct virtqueue *vq)
 {
@@ -659,8 +679,13 @@
 				       int page_off,
 				       unsigned int *len)
 {
-	struct page *page = alloc_page(GFP_ATOMIC);
+	int tailroom = SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+	struct page *page;
+
+	if (page_off + *len + tailroom > PAGE_SIZE)
+		return NULL;
 
+	page = alloc_page(GFP_ATOMIC);
 	if (!page)
 		return NULL;
 
@@ -668,7 +693,6 @@
 	page_off += *len;
 
 	while (--*num_buf) {
-		int tailroom = SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
 		unsigned int buflen;
 		void *buf;
 		int off;
@@ -965,6 +989,24 @@
 			 * xdp.data_meta were adjusted
 			 */
 			len = xdp.data_end - xdp.data + vi->hdr_len + metasize;
+
+			/* recalculate headroom if xdp.data or xdp_data_meta
+			 * were adjusted, note that offset should always point
+			 * to the start of the reserved bytes for virtio_net
+			 * header which are followed by xdp.data, that means
+			 * that offset is equal to the headroom (when buf is
+			 * starting at the beginning of the page, otherwise
+			 * there is a base offset inside the page) but it's used
+			 * with a different starting point (buf start) than
+			 * xdp.data (buf start + vnet hdr size). If xdp.data or
+			 * data_meta were adjusted by the xdp prog then the
+			 * headroom size has changed and so has the offset, we
+			 * can use data_hard_start, which points at buf start +
+			 * vnet hdr size, to calculate the new headroom and use
+			 * it later to compute buf start in page_to_skb()
+			 */
+			headroom = xdp.data - xdp.data_hard_start - metasize;
+
 			/* We can only create skb based on xdp_page. */
 			if (unlikely(xdp_page != page)) {
 				rcu_read_unlock();
@@ -972,15 +1014,18 @@
 				head_skb = page_to_skb(vi, rq, xdp_page, offset,
 						       len, PAGE_SIZE, false,
 						       metasize,
-						       VIRTIO_XDP_HEADROOM);
+						       headroom);
 				return head_skb;
 			}
 			break;
 		case XDP_TX:
 			stats->xdp_tx++;
 			xdpf = xdp_convert_buff_to_frame(&xdp);
-			if (unlikely(!xdpf))
+			if (unlikely(!xdpf)) {
+				if (unlikely(xdp_page != page))
+					put_page(xdp_page);
 				goto err_xdp;
+			}
 			err = virtnet_xdp_xmit(dev, 1, &xdpf, 0);
 			if (unlikely(!err)) {
 				xdp_return_frame_rx_napi(xdpf);
@@ -1436,8 +1481,12 @@
 	}
 
 	if (rq->vq->num_free > min((unsigned int)budget, virtqueue_get_vring_size(rq->vq)) / 2) {
-		if (!try_fill_recv(vi, rq, GFP_ATOMIC))
-			schedule_delayed_work(&vi->refill, 0);
+		if (!try_fill_recv(vi, rq, GFP_ATOMIC)) {
+			spin_lock(&vi->refill_lock);
+			if (vi->refill_enabled)
+				schedule_delayed_work(&vi->refill, 0);
+			spin_unlock(&vi->refill_lock);
+		}
 	}
 
 	u64_stats_update_begin(&rq->stats.syncp);
@@ -1499,7 +1548,7 @@
 		return false;
 }
 
-static void virtnet_poll_cleantx(struct receive_queue *rq)
+static void virtnet_poll_cleantx(struct receive_queue *rq, int budget)
 {
 	struct virtnet_info *vi = rq->vq->vdev->priv;
 	unsigned int index = vq2rxq(rq->vq);
@@ -1512,7 +1561,7 @@
 	if (__netif_tx_trylock(txq)) {
 		do {
 			virtqueue_disable_cb(sq->vq);
-			free_old_xmit_skbs(sq, true);
+			free_old_xmit_skbs(sq, !!budget);
 		} while (unlikely(!virtqueue_enable_cb_delayed(sq->vq)));
 
 		if (sq->vq->num_free >= 2 + MAX_SKB_FRAGS)
@@ -1531,17 +1580,17 @@
 	unsigned int received;
 	unsigned int xdp_xmit = 0;
 
-	virtnet_poll_cleantx(rq);
+	virtnet_poll_cleantx(rq, budget);
 
 	received = virtnet_receive(rq, budget, &xdp_xmit);
 
+	if (xdp_xmit & VIRTIO_XDP_REDIR)
+		xdp_do_flush();
+
 	/* Out of packets? */
 	if (received < budget)
 		virtqueue_napi_complete(napi, rq->vq, received);
 
-	if (xdp_xmit & VIRTIO_XDP_REDIR)
-		xdp_do_flush();
-
 	if (xdp_xmit & VIRTIO_XDP_TX) {
 		sq = virtnet_xdp_get_sq(vi);
 		if (virtqueue_kick_prepare(sq->vq) && virtqueue_notify(sq->vq)) {
@@ -1555,33 +1604,65 @@
 	return received;
 }
 
+static void virtnet_disable_queue_pair(struct virtnet_info *vi, int qp_index)
+{
+	virtnet_napi_tx_disable(&vi->sq[qp_index].napi);
+	napi_disable(&vi->rq[qp_index].napi);
+	xdp_rxq_info_unreg(&vi->rq[qp_index].xdp_rxq);
+}
+
+static int virtnet_enable_queue_pair(struct virtnet_info *vi, int qp_index)
+{
+	struct net_device *dev = vi->dev;
+	int err;
+
+	err = xdp_rxq_info_reg(&vi->rq[qp_index].xdp_rxq, dev, qp_index,
+			       vi->rq[qp_index].napi.napi_id);
+	if (err < 0)
+		return err;
+
+	err = xdp_rxq_info_reg_mem_model(&vi->rq[qp_index].xdp_rxq,
+					 MEM_TYPE_PAGE_SHARED, NULL);
+	if (err < 0)
+		goto err_xdp_reg_mem_model;
+
+	virtnet_napi_enable(vi->rq[qp_index].vq, &vi->rq[qp_index].napi);
+	virtnet_napi_tx_enable(vi, vi->sq[qp_index].vq, &vi->sq[qp_index].napi);
+
+	return 0;
+
+err_xdp_reg_mem_model:
+	xdp_rxq_info_unreg(&vi->rq[qp_index].xdp_rxq);
+	return err;
+}
+
 static int virtnet_open(struct net_device *dev)
 {
 	struct virtnet_info *vi = netdev_priv(dev);
 	int i, err;
 
+	enable_delayed_refill(vi);
+
 	for (i = 0; i < vi->max_queue_pairs; i++) {
 		if (i < vi->curr_queue_pairs)
 			/* Make sure we have some buffers: if oom use wq. */
 			if (!try_fill_recv(vi, &vi->rq[i], GFP_KERNEL))
 				schedule_delayed_work(&vi->refill, 0);
 
-		err = xdp_rxq_info_reg(&vi->rq[i].xdp_rxq, dev, i, vi->rq[i].napi.napi_id);
+		err = virtnet_enable_queue_pair(vi, i);
 		if (err < 0)
-			return err;
-
-		err = xdp_rxq_info_reg_mem_model(&vi->rq[i].xdp_rxq,
-						 MEM_TYPE_PAGE_SHARED, NULL);
-		if (err < 0) {
-			xdp_rxq_info_unreg(&vi->rq[i].xdp_rxq);
-			return err;
-		}
-
-		virtnet_napi_enable(vi->rq[i].vq, &vi->rq[i].napi);
-		virtnet_napi_tx_enable(vi, vi->sq[i].vq, &vi->sq[i].napi);
+			goto err_enable_qp;
 	}
 
 	return 0;
+
+err_enable_qp:
+	disable_delayed_refill(vi);
+	cancel_delayed_work_sync(&vi->refill);
+
+	for (i--; i >= 0; i--)
+		virtnet_disable_queue_pair(vi, i);
+	return err;
 }
 
 static int virtnet_poll_tx(struct napi_struct *napi, int budget)
@@ -1602,7 +1683,7 @@
 	txq = netdev_get_tx_queue(vi->dev, index);
 	__netif_tx_lock(txq, raw_smp_processor_id());
 	virtqueue_disable_cb(sq->vq);
-	free_old_xmit_skbs(sq, true);
+	free_old_xmit_skbs(sq, !!budget);
 
 	if (sq->vq->num_free >= 2 + MAX_SKB_FRAGS)
 		netif_tx_wake_queue(txq);
@@ -1733,8 +1814,10 @@
 	 */
 	if (sq->vq->num_free < 2+MAX_SKB_FRAGS) {
 		netif_stop_subqueue(dev, qnum);
-		if (!use_napi &&
-		    unlikely(!virtqueue_enable_cb_delayed(sq->vq))) {
+		if (use_napi) {
+			if (unlikely(!virtqueue_enable_cb_delayed(sq->vq)))
+				virtqueue_napi_schedule(&sq->napi, sq->vq);
+		} else if (unlikely(!virtqueue_enable_cb_delayed(sq->vq))) {
 			/* More just got used, free them then recheck. */
 			free_old_xmit_skbs(sq, false);
 			if (sq->vq->num_free >= 2+MAX_SKB_FRAGS) {
@@ -1940,14 +2023,13 @@
 	struct virtnet_info *vi = netdev_priv(dev);
 	int i;
 
+	/* Make sure NAPI doesn't schedule refill work */
+	disable_delayed_refill(vi);
 	/* Make sure refill_work doesn't re-enable napi! */
 	cancel_delayed_work_sync(&vi->refill);
 
-	for (i = 0; i < vi->max_queue_pairs; i++) {
-		xdp_rxq_info_unreg(&vi->rq[i].xdp_rxq);
-		napi_disable(&vi->rq[i].napi);
-		virtnet_napi_tx_disable(&vi->sq[i].napi);
-	}
+	for (i = 0; i < vi->max_queue_pairs; i++)
+		virtnet_disable_queue_pair(vi, i);
 
 	return 0;
 }
@@ -2413,7 +2495,6 @@
 static void virtnet_freeze_down(struct virtio_device *vdev)
 {
 	struct virtnet_info *vi = vdev->priv;
-	int i;
 
 	/* Make sure no work handler is accessing the device */
 	flush_work(&vi->config_work);
@@ -2421,14 +2502,8 @@
 	netif_tx_lock_bh(vi->dev);
 	netif_device_detach(vi->dev);
 	netif_tx_unlock_bh(vi->dev);
-	cancel_delayed_work_sync(&vi->refill);
-
-	if (netif_running(vi->dev)) {
-		for (i = 0; i < vi->max_queue_pairs; i++) {
-			napi_disable(&vi->rq[i].napi);
-			virtnet_napi_tx_disable(&vi->sq[i].napi);
-		}
-	}
+	if (netif_running(vi->dev))
+		virtnet_close(vi->dev);
 }
 
 static int init_vqs(struct virtnet_info *vi);
@@ -2436,7 +2511,7 @@
 static int virtnet_restore_up(struct virtio_device *vdev)
 {
 	struct virtnet_info *vi = vdev->priv;
-	int err, i;
+	int err;
 
 	err = init_vqs(vi);
 	if (err)
@@ -2444,16 +2519,12 @@
 
 	virtio_device_ready(vdev);
 
-	if (netif_running(vi->dev)) {
-		for (i = 0; i < vi->curr_queue_pairs; i++)
-			if (!try_fill_recv(vi, &vi->rq[i], GFP_KERNEL))
-				schedule_delayed_work(&vi->refill, 0);
+	enable_delayed_refill(vi);
 
-		for (i = 0; i < vi->max_queue_pairs; i++) {
-			virtnet_napi_enable(vi->rq[i].vq, &vi->rq[i].napi);
-			virtnet_napi_tx_enable(vi, vi->sq[i].vq,
-					       &vi->sq[i].napi);
-		}
+	if (netif_running(vi->dev)) {
+		err = virtnet_open(vi->dev);
+		if (err)
+			return err;
 	}
 
 	netif_tx_lock_bh(vi->dev);
@@ -2770,6 +2841,27 @@
 			put_page(vi->rq[i].alloc_frag.page);
 }
 
+static void virtnet_sq_free_unused_buf(struct virtqueue *vq, void *buf)
+{
+	if (!is_xdp_frame(buf))
+		dev_kfree_skb(buf);
+	else
+		xdp_return_frame(ptr_to_xdp(buf));
+}
+
+static void virtnet_rq_free_unused_buf(struct virtqueue *vq, void *buf)
+{
+	struct virtnet_info *vi = vq->vdev->priv;
+	int i = vq2rxq(vq);
+
+	if (vi->mergeable_rx_bufs)
+		put_page(virt_to_head_page(buf));
+	else if (vi->big_packets)
+		give_pages(&vi->rq[i], buf);
+	else
+		put_page(virt_to_head_page(buf));
+}
+
 static void free_unused_bufs(struct virtnet_info *vi)
 {
 	void *buf;
@@ -2777,26 +2869,16 @@
 
 	for (i = 0; i < vi->max_queue_pairs; i++) {
 		struct virtqueue *vq = vi->sq[i].vq;
-		while ((buf = virtqueue_detach_unused_buf(vq)) != NULL) {
-			if (!is_xdp_frame(buf))
-				dev_kfree_skb(buf);
-			else
-				xdp_return_frame(ptr_to_xdp(buf));
-		}
+		while ((buf = virtqueue_detach_unused_buf(vq)) != NULL)
+			virtnet_sq_free_unused_buf(vq, buf);
+		cond_resched();
 	}
 
 	for (i = 0; i < vi->max_queue_pairs; i++) {
 		struct virtqueue *vq = vi->rq[i].vq;
-
-		while ((buf = virtqueue_detach_unused_buf(vq)) != NULL) {
-			if (vi->mergeable_rx_bufs) {
-				put_page(virt_to_head_page(buf));
-			} else if (vi->big_packets) {
-				give_pages(&vi->rq[i], buf);
-			} else {
-				put_page(virt_to_head_page(buf));
-			}
-		}
+		while ((buf = virtqueue_detach_unused_buf(vq)) != NULL)
+			virtnet_rq_free_unused_buf(vq, buf);
+		cond_resched();
 	}
 }
 
@@ -2831,10 +2913,11 @@
 {
 	vq_callback_t **callbacks;
 	struct virtqueue **vqs;
-	int ret = -ENOMEM;
-	int i, total_vqs;
 	const char **names;
+	int ret = -ENOMEM;
+	int total_vqs;
 	bool *ctx;
+	u16 i;
 
 	/* We expect 1 RX virtqueue followed by 1 TX virtqueue, followed by
 	 * possible N-1 RX/TX queue pairs used in multiqueue mode, followed by
@@ -2871,8 +2954,8 @@
 	for (i = 0; i < vi->max_queue_pairs; i++) {
 		callbacks[rxq2vq(i)] = skb_recv_done;
 		callbacks[txq2vq(i)] = skb_xmit_done;
-		sprintf(vi->rq[i].name, "input.%d", i);
-		sprintf(vi->sq[i].name, "output.%d", i);
+		sprintf(vi->rq[i].name, "input.%u", i);
+		sprintf(vi->sq[i].name, "output.%u", i);
 		names[rxq2vq(i)] = vi->rq[i].name;
 		names[txq2vq(i)] = vi->sq[i].name;
 		if (ctx)
@@ -3128,8 +3211,16 @@
 			dev->features |= dev->hw_features & NETIF_F_ALL_TSO;
 		/* (!csum && gso) case will be fixed by register_netdev() */
 	}
-	if (virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_CSUM))
-		dev->features |= NETIF_F_RXCSUM;
+
+	/* 1. With VIRTIO_NET_F_GUEST_CSUM negotiation, the driver doesn't
+	 * need to calculate checksums for partially checksummed packets,
+	 * as they're considered valid by the upper layer.
+	 * 2. Without VIRTIO_NET_F_GUEST_CSUM negotiation, the driver only
+	 * receives fully checksummed packets. The device may assist in
+	 * validating these packets' checksums, so the driver won't have to.
+	 */
+	dev->features |= NETIF_F_RXCSUM;
+
 	if (virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO4) ||
 	    virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO6))
 		dev->features |= NETIF_F_GRO_HW;
@@ -3157,6 +3248,7 @@
 	vdev->priv = vi;
 
 	INIT_WORK(&vi->config_work, virtnet_config_changed_work);
+	spin_lock_init(&vi->refill_lock);
 
 	/* If we can receive ANY GSO packets, we must allocate large ones. */
 	if (virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO4) ||
@@ -3236,22 +3328,28 @@
 		}
 	}
 
-	err = register_netdev(dev);
+	/* serialize netdev register + virtio_device_ready() with ndo_open() */
+	rtnl_lock();
+
+	err = register_netdevice(dev);
 	if (err) {
 		pr_debug("virtio_net: registering device failed\n");
+		rtnl_unlock();
 		goto free_failover;
 	}
 
 	virtio_device_ready(vdev);
 
+	_virtnet_set_queues(vi, vi->curr_queue_pairs);
+
+	rtnl_unlock();
+
 	err = virtnet_cpu_notif_add(vi);
 	if (err) {
 		pr_debug("virtio_net: registering cpu notifier failed\n");
 		goto free_unregister_netdev;
 	}
 
-	virtnet_set_queues(vi, vi->curr_queue_pairs);
-
 	/* Assume link up if device can't report link status,
 	   otherwise get link status from config. */
 	netif_carrier_off(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/vmxnet3/vmxnet3_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/vmxnet3/vmxnet3_drv.c
@@ -75,8 +75,14 @@
 
 	for (i = 0; i < adapter->intr.num_intrs; i++)
 		vmxnet3_enable_intr(adapter, i);
-	adapter->shared->devRead.intrConf.intrCtrl &=
+	if (!VMXNET3_VERSION_GE_6(adapter) ||
+	    !adapter->queuesExtEnabled) {
+		adapter->shared->devRead.intrConf.intrCtrl &=
+					cpu_to_le32(~VMXNET3_IC_DISABLE_ALL);
+	} else {
+		adapter->shared->devReadExt.intrConfExt.intrCtrl &=
 					cpu_to_le32(~VMXNET3_IC_DISABLE_ALL);
+	}
 }
 
 
@@ -85,8 +91,14 @@
 {
 	int i;
 
-	adapter->shared->devRead.intrConf.intrCtrl |=
+	if (!VMXNET3_VERSION_GE_6(adapter) ||
+	    !adapter->queuesExtEnabled) {
+		adapter->shared->devRead.intrConf.intrCtrl |=
 					cpu_to_le32(VMXNET3_IC_DISABLE_ALL);
+	} else {
+		adapter->shared->devReadExt.intrConfExt.intrCtrl |=
+					cpu_to_le32(VMXNET3_IC_DISABLE_ALL);
+	}
 	for (i = 0; i < adapter->intr.num_intrs; i++)
 		vmxnet3_disable_intr(adapter, i);
 }
@@ -589,6 +601,7 @@
 				if (dma_mapping_error(&adapter->pdev->dev,
 						      rbi->dma_addr)) {
 					dev_kfree_skb_any(rbi->skb);
+					rbi->skb = NULL;
 					rq->stats.rx_buf_alloc_failure++;
 					break;
 				}
@@ -613,6 +626,7 @@
 				if (dma_mapping_error(&adapter->pdev->dev,
 						      rbi->dma_addr)) {
 					put_page(rbi->page);
+					rbi->page = NULL;
 					rq->stats.rx_buf_alloc_failure++;
 					break;
 				}
@@ -1228,6 +1242,10 @@
 		    (le32_to_cpu(gdesc->dword[3]) &
 		     VMXNET3_RCD_CSUM_OK) == VMXNET3_RCD_CSUM_OK) {
 			skb->ip_summed = CHECKSUM_UNNECESSARY;
+			if ((le32_to_cpu(gdesc->dword[0]) &
+				     (1UL << VMXNET3_RCD_HDR_INNER_SHIFT))) {
+				skb->csum_level = 1;
+			}
 			WARN_ON_ONCE(!(gdesc->rcd.tcp || gdesc->rcd.udp) &&
 				     !(le32_to_cpu(gdesc->dword[0]) &
 				     (1UL << VMXNET3_RCD_HDR_INNER_SHIFT)));
@@ -1237,6 +1255,10 @@
 		} else if (gdesc->rcd.v6 && (le32_to_cpu(gdesc->dword[3]) &
 					     (1 << VMXNET3_RCD_TUC_SHIFT))) {
 			skb->ip_summed = CHECKSUM_UNNECESSARY;
+			if ((le32_to_cpu(gdesc->dword[0]) &
+				     (1UL << VMXNET3_RCD_HDR_INNER_SHIFT))) {
+				skb->csum_level = 1;
+			}
 			WARN_ON_ONCE(!(gdesc->rcd.tcp || gdesc->rcd.udp) &&
 				     !(le32_to_cpu(gdesc->dword[0]) &
 				     (1UL << VMXNET3_RCD_HDR_INNER_SHIFT)));
@@ -1348,6 +1370,7 @@
 	};
 	u32 num_pkts = 0;
 	bool skip_page_frags = false;
+	bool encap_lro = false;
 	struct Vmxnet3_RxCompDesc *rcd;
 	struct vmxnet3_rx_ctx *ctx = &rq->rx_ctx;
 	u16 segCnt = 0, mss = 0;
@@ -1506,13 +1529,18 @@
 			if (VMXNET3_VERSION_GE_2(adapter) &&
 			    rcd->type == VMXNET3_CDTYPE_RXCOMP_LRO) {
 				struct Vmxnet3_RxCompDescExt *rcdlro;
+				union Vmxnet3_GenericDesc *gdesc;
+
 				rcdlro = (struct Vmxnet3_RxCompDescExt *)rcd;
+				gdesc = (union Vmxnet3_GenericDesc *)rcd;
 
 				segCnt = rcdlro->segCnt;
 				WARN_ON_ONCE(segCnt == 0);
 				mss = rcdlro->mss;
 				if (unlikely(segCnt <= 1))
 					segCnt = 0;
+				encap_lro = (le32_to_cpu(gdesc->dword[0]) &
+					(1UL << VMXNET3_RCD_HDR_INNER_SHIFT));
 			} else {
 				segCnt = 0;
 			}
@@ -1580,7 +1608,7 @@
 			vmxnet3_rx_csum(adapter, skb,
 					(union Vmxnet3_GenericDesc *)rcd);
 			skb->protocol = eth_type_trans(skb, adapter->netdev);
-			if (!rcd->tcp ||
+			if ((!rcd->tcp && !encap_lro) ||
 			    !(adapter->netdev->features & NETIF_F_LRO))
 				goto not_lro;
 
@@ -1589,7 +1617,7 @@
 					SKB_GSO_TCPV4 : SKB_GSO_TCPV6;
 				skb_shinfo(skb)->gso_size = mss;
 				skb_shinfo(skb)->gso_segs = segCnt;
-			} else if (segCnt != 0 || skb->len > mtu) {
+			} else if ((segCnt != 0 || skb->len > mtu) && !encap_lro) {
 				u32 hlen;
 
 				hlen = vmxnet3_get_hdr_len(adapter, skb,
@@ -1618,6 +1646,7 @@
 				napi_gro_receive(&rq->napi, skb);
 
 			ctx->skb = NULL;
+			encap_lro = false;
 			num_pkts++;
 		}
 
@@ -1666,6 +1695,10 @@
 	u32 i, ring_idx;
 	struct Vmxnet3_RxDesc *rxd;
 
+	/* ring has already been cleaned up */
+	if (!rq->rx_ring[0].base)
+		return;
+
 	for (ring_idx = 0; ring_idx < 2; ring_idx++) {
 		for (i = 0; i < rq->rx_ring[ring_idx].size; i++) {
 #ifdef __BIG_ENDIAN_BITFIELD
@@ -3261,7 +3294,7 @@
 
 #ifdef CONFIG_PCI_MSI
 	if (adapter->intr.type == VMXNET3_IT_MSIX) {
-		int i, nvec;
+		int i, nvec, nvec_allocated;
 
 		nvec  = adapter->share_intr == VMXNET3_INTR_TXSHARE ?
 			1 : adapter->num_tx_queues;
@@ -3274,14 +3307,15 @@
 		for (i = 0; i < nvec; i++)
 			adapter->intr.msix_entries[i].entry = i;
 
-		nvec = vmxnet3_acquire_msix_vectors(adapter, nvec);
-		if (nvec < 0)
+		nvec_allocated = vmxnet3_acquire_msix_vectors(adapter, nvec);
+		if (nvec_allocated < 0)
 			goto msix_err;
 
 		/* If we cannot allocate one MSIx vector per queue
 		 * then limit the number of rx queues to 1
 		 */
-		if (nvec == VMXNET3_LINUX_MIN_MSIX_VECT) {
+		if (nvec_allocated == VMXNET3_LINUX_MIN_MSIX_VECT &&
+		    nvec != VMXNET3_LINUX_MIN_MSIX_VECT) {
 			if (adapter->share_intr != VMXNET3_INTR_BUDDYSHARE
 			    || adapter->num_rx_queues != 1) {
 				adapter->share_intr = VMXNET3_INTR_TXSHARE;
@@ -3291,14 +3325,14 @@
 			}
 		}
 
-		adapter->intr.num_intrs = nvec;
+		adapter->intr.num_intrs = nvec_allocated;
 		return;
 
 msix_err:
 		/* If we cannot allocate MSIx vectors use only one rx queue */
 		dev_info(&adapter->pdev->dev,
 			 "Failed to enable MSI-X, error %d. "
-			 "Limiting #rx queues to 1, try MSI.\n", nvec);
+			 "Limiting #rx queues to 1, try MSI.\n", nvec_allocated);
 
 		adapter->intr.type = VMXNET3_IT_MSI;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/vrf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/vrf.c
@@ -35,6 +35,7 @@
 #include <net/l3mdev.h>
 #include <net/fib_rules.h>
 #include <net/netns/generic.h>
+#include <net/netfilter/nf_conntrack.h>
 
 #define DRV_NAME	"vrf"
 #define DRV_VERSION	"1.1"
@@ -424,12 +425,26 @@
 	return NETDEV_TX_OK;
 }
 
+static void vrf_nf_set_untracked(struct sk_buff *skb)
+{
+	if (skb_get_nfct(skb) == 0)
+		nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
+}
+
+static void vrf_nf_reset_ct(struct sk_buff *skb)
+{
+	if (skb_get_nfct(skb) == IP_CT_UNTRACKED)
+		nf_reset_ct(skb);
+}
+
 #if IS_ENABLED(CONFIG_IPV6)
 static int vrf_ip6_local_out(struct net *net, struct sock *sk,
 			     struct sk_buff *skb)
 {
 	int err;
 
+	vrf_nf_reset_ct(skb);
+
 	err = nf_hook(NFPROTO_IPV6, NF_INET_LOCAL_OUT, net,
 		      sk, skb, NULL, skb_dst(skb)->dev, dst_output);
 
@@ -456,14 +471,13 @@
 
 	memset(&fl6, 0, sizeof(fl6));
 	/* needed to match OIF rule */
-	fl6.flowi6_oif = dev->ifindex;
+	fl6.flowi6_l3mdev = dev->ifindex;
 	fl6.flowi6_iif = LOOPBACK_IFINDEX;
 	fl6.daddr = iph->daddr;
 	fl6.saddr = iph->saddr;
 	fl6.flowlabel = ip6_flowinfo(iph);
 	fl6.flowi6_mark = skb->mark;
 	fl6.flowi6_proto = iph->nexthdr;
-	fl6.flowi6_flags = FLOWI_FLAG_SKIP_NH_OIF;
 
 	dst = ip6_dst_lookup_flow(net, NULL, &fl6, NULL);
 	if (IS_ERR(dst) || dst == dst_null)
@@ -482,6 +496,7 @@
 	/* strip the ethernet header added for pass through VRF device */
 	__skb_pull(skb, skb_network_offset(skb));
 
+	memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
 	ret = vrf_ip6_local_out(net, skb->sk, skb);
 	if (unlikely(net_xmit_eval(ret)))
 		dev->stats.tx_errors++;
@@ -508,6 +523,8 @@
 {
 	int err;
 
+	vrf_nf_reset_ct(skb);
+
 	err = nf_hook(NFPROTO_IPV4, NF_INET_LOCAL_OUT, net, sk,
 		      skb, NULL, skb_dst(skb)->dev, dst_output);
 	if (likely(err == 1))
@@ -532,10 +549,10 @@
 
 	memset(&fl4, 0, sizeof(fl4));
 	/* needed to match OIF rule */
-	fl4.flowi4_oif = vrf_dev->ifindex;
+	fl4.flowi4_l3mdev = vrf_dev->ifindex;
 	fl4.flowi4_iif = LOOPBACK_IFINDEX;
 	fl4.flowi4_tos = RT_TOS(ip4h->tos);
-	fl4.flowi4_flags = FLOWI_FLAG_ANYSRC | FLOWI_FLAG_SKIP_NH_OIF;
+	fl4.flowi4_flags = FLOWI_FLAG_ANYSRC;
 	fl4.flowi4_proto = ip4h->protocol;
 	fl4.daddr = ip4h->daddr;
 	fl4.saddr = ip4h->saddr;
@@ -562,6 +579,7 @@
 					       RT_SCOPE_LINK);
 	}
 
+	memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
 	ret = vrf_ip_local_out(dev_net(skb_dst(skb)->dev), skb->sk, skb);
 	if (unlikely(net_xmit_eval(ret)))
 		vrf_dev->stats.tx_errors++;
@@ -626,8 +644,7 @@
 		skb_pull(skb, ETH_HLEN);
 	}
 
-	/* reset skb device */
-	nf_reset_ct(skb);
+	vrf_nf_reset_ct(skb);
 }
 
 #if IS_ENABLED(CONFIG_IPV6)
@@ -641,7 +658,7 @@
 	struct neighbour *neigh;
 	int ret;
 
-	nf_reset_ct(skb);
+	vrf_nf_reset_ct(skb);
 
 	skb->protocol = htons(ETH_P_IPV6);
 	skb->dev = dev;
@@ -772,6 +789,8 @@
 	if (rt6_need_strict(&ipv6_hdr(skb)->daddr))
 		return skb;
 
+	vrf_nf_set_untracked(skb);
+
 	if (qdisc_tx_is_default(vrf_dev) ||
 	    IP6CB(skb)->flags & IP6SKB_XFRM_TRANSFORMED)
 		return vrf_ip6_out_direct(vrf_dev, sk, skb);
@@ -858,7 +877,7 @@
 	struct neighbour *neigh;
 	bool is_v6gw = false;
 
-	nf_reset_ct(skb);
+	vrf_nf_reset_ct(skb);
 
 	/* Be paranoid, rather than too clever. */
 	if (unlikely(skb_headroom(skb) < hh_len && dev->header_ops)) {
@@ -1001,6 +1020,8 @@
 	    ipv4_is_lbcast(ip_hdr(skb)->daddr))
 		return skb;
 
+	vrf_nf_set_untracked(skb);
+
 	if (qdisc_tx_is_default(vrf_dev) ||
 	    IPCB(skb)->flags & IPSKB_XFRM_TRANSFORMED)
 		return vrf_ip_out_direct(vrf_dev, sk, skb);
@@ -1243,6 +1264,7 @@
 	eth = (struct ethhdr *)skb->data;
 
 	skb_reset_mac_header(skb);
+	skb_reset_mac_len(skb);
 
 	/* we set the ethernet destination and the source addresses to the
 	 * address of the VRF device.
@@ -1272,9 +1294,9 @@
  */
 static int vrf_add_mac_header_if_unset(struct sk_buff *skb,
 				       struct net_device *vrf_dev,
-				       u16 proto)
+				       u16 proto, struct net_device *orig_dev)
 {
-	if (skb_mac_header_was_set(skb))
+	if (skb_mac_header_was_set(skb) && dev_has_header(orig_dev))
 		return 0;
 
 	return vrf_prepare_mac_header(skb, vrf_dev, proto);
@@ -1362,8 +1384,8 @@
 
 	/* loopback, multicast & non-ND link-local traffic; do not push through
 	 * packet taps again. Reset pkt_type for upper layers to process skb.
-	 * For strict packets with a source LLA, determine the dst using the
-	 * original ifindex.
+	 * For non-loopback strict packets, determine the dst using the original
+	 * ifindex.
 	 */
 	if (skb->pkt_type == PACKET_LOOPBACK || (need_strict && !is_ndisc)) {
 		skb->dev = vrf_dev;
@@ -1372,7 +1394,7 @@
 
 		if (skb->pkt_type == PACKET_LOOPBACK)
 			skb->pkt_type = PACKET_HOST;
-		else if (ipv6_addr_type(&ipv6_hdr(skb)->saddr) & IPV6_ADDR_LINKLOCAL)
+		else
 			vrf_ip6_input_dst(skb, vrf_dev, orig_iif);
 
 		goto out;
@@ -1380,6 +1402,8 @@
 
 	/* if packet is NDISC then keep the ingress interface */
 	if (!is_ndisc) {
+		struct net_device *orig_dev = skb->dev;
+
 		vrf_rx_stats(vrf_dev, skb->len);
 		skb->dev = vrf_dev;
 		skb->skb_iif = vrf_dev->ifindex;
@@ -1388,7 +1412,8 @@
 			int err;
 
 			err = vrf_add_mac_header_if_unset(skb, vrf_dev,
-							  ETH_P_IPV6);
+							  ETH_P_IPV6,
+							  orig_dev);
 			if (likely(!err)) {
 				skb_push(skb, skb->mac_len);
 				dev_queue_xmit_nit(skb, vrf_dev);
@@ -1418,6 +1443,8 @@
 static struct sk_buff *vrf_ip_rcv(struct net_device *vrf_dev,
 				  struct sk_buff *skb)
 {
+	struct net_device *orig_dev = skb->dev;
+
 	skb->dev = vrf_dev;
 	skb->skb_iif = vrf_dev->ifindex;
 	IPCB(skb)->flags |= IPSKB_L3SLAVE;
@@ -1438,7 +1465,8 @@
 	if (!list_empty(&vrf_dev->ptype_all)) {
 		int err;
 
-		err = vrf_add_mac_header_if_unset(skb, vrf_dev, ETH_P_IP);
+		err = vrf_add_mac_header_if_unset(skb, vrf_dev, ETH_P_IP,
+						  orig_dev);
 		if (likely(!err)) {
 			skb_push(skb, skb->mac_len);
 			dev_queue_xmit_nit(skb, vrf_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/vxlan/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/vxlan/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the vxlan driver
+#
+
+obj-$(CONFIG_VXLAN) += vxlan.o
+
+vxlan-objs := vxlan_core.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/vxlan/vxlan_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/vxlan/vxlan_core.c
@@ -0,0 +1,5079 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * VXLAN: Virtual eXtensible Local Area Network
+ *
+ * Copyright (c) 2012-2013 Vyatta Inc.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/udp.h>
+#include <linux/igmp.h>
+#include <linux/inetdevice.h>
+#include <linux/if_ether.h>
+#include <linux/ethtool.h>
+#include <net/arp.h>
+#include <net/ndisc.h>
+#include <net/ipv6_stubs.h>
+#include <net/ip.h>
+#include <net/icmp.h>
+#include <net/rtnetlink.h>
+#include <net/inet_ecn.h>
+#include <net/net_namespace.h>
+#include <net/netns/generic.h>
+#include <net/tun_proto.h>
+#include <net/vxlan.h>
+#include <net/nexthop.h>
+
+#if IS_ENABLED(CONFIG_IPV6)
+#include <net/ip6_tunnel.h>
+#include <net/ip6_checksum.h>
+#endif
+
+#define VXLAN_VERSION	"0.1"
+
+#define PORT_HASH_BITS	8
+#define PORT_HASH_SIZE  (1<<PORT_HASH_BITS)
+#define FDB_AGE_DEFAULT 300 /* 5 min */
+#define FDB_AGE_INTERVAL (10 * HZ)	/* rescan interval */
+
+/* UDP port for VXLAN traffic.
+ * The IANA assigned port is 4789, but the Linux default is 8472
+ * for compatibility with early adopters.
+ */
+static unsigned short vxlan_port __read_mostly = 8472;
+module_param_named(udp_port, vxlan_port, ushort, 0444);
+MODULE_PARM_DESC(udp_port, "Destination UDP port");
+
+static bool log_ecn_error = true;
+module_param(log_ecn_error, bool, 0644);
+MODULE_PARM_DESC(log_ecn_error, "Log packets received with corrupted ECN");
+
+static unsigned int vxlan_net_id;
+static struct rtnl_link_ops vxlan_link_ops;
+
+static const u8 all_zeros_mac[ETH_ALEN + 2];
+
+static int vxlan_sock_add(struct vxlan_dev *vxlan);
+
+static void vxlan_vs_del_dev(struct vxlan_dev *vxlan);
+
+/* per-network namespace private data for this module */
+struct vxlan_net {
+	struct list_head  vxlan_list;
+	struct hlist_head sock_list[PORT_HASH_SIZE];
+	spinlock_t	  sock_lock;
+	struct notifier_block nexthop_notifier_block;
+};
+
+/* Forwarding table entry */
+struct vxlan_fdb {
+	struct hlist_node hlist;	/* linked list of entries */
+	struct rcu_head	  rcu;
+	unsigned long	  updated;	/* jiffies */
+	unsigned long	  used;
+	struct list_head  remotes;
+	u8		  eth_addr[ETH_ALEN];
+	u16		  state;	/* see ndm_state */
+	__be32		  vni;
+	u16		  flags;	/* see ndm_flags and below */
+	struct list_head  nh_list;
+	struct nexthop __rcu *nh;
+	struct vxlan_dev  __rcu *vdev;
+};
+
+#define NTF_VXLAN_ADDED_BY_USER 0x100
+
+/* salt for hash table */
+static u32 vxlan_salt __read_mostly;
+
+static inline bool vxlan_collect_metadata(struct vxlan_sock *vs)
+{
+	return vs->flags & VXLAN_F_COLLECT_METADATA ||
+	       ip_tunnel_collect_metadata();
+}
+
+static struct ip_fan_map *vxlan_fan_find_map(struct vxlan_dev *vxlan, __be32 daddr)
+{
+	struct ip_fan_map *fan_map;
+
+	rcu_read_lock();
+	list_for_each_entry_rcu(fan_map, &vxlan->fan.fan_maps, list) {
+		if (fan_map->overlay ==
+		    (daddr & inet_make_mask(fan_map->overlay_prefix))) {
+			rcu_read_unlock();
+			return fan_map;
+		}
+	}
+	rcu_read_unlock();
+
+	return NULL;
+}
+
+static void vxlan_fan_flush_map(struct vxlan_dev *vxlan)
+{
+	struct ip_fan_map *fan_map;
+
+	list_for_each_entry_rcu(fan_map, &vxlan->fan.fan_maps, list) {
+		list_del_rcu(&fan_map->list);
+		kfree_rcu(fan_map, rcu);
+	}
+}
+
+static int vxlan_fan_del_map(struct vxlan_dev *vxlan, __be32 overlay)
+{
+	struct ip_fan_map *fan_map;
+
+	fan_map = vxlan_fan_find_map(vxlan, overlay);
+	if (!fan_map)
+		return -ENOENT;
+
+	list_del_rcu(&fan_map->list);
+	kfree_rcu(fan_map, rcu);
+
+	return 0;
+}
+
+static int vxlan_fan_add_map(struct vxlan_dev *vxlan, struct ifla_fan_map *map)
+{
+	__be32 overlay_mask, underlay_mask;
+	struct ip_fan_map *fan_map;
+
+	overlay_mask = inet_make_mask(map->overlay_prefix);
+	underlay_mask = inet_make_mask(map->underlay_prefix);
+
+	netdev_dbg(vxlan->dev, "vfam: map: o %x/%d u %x/%d om %x um %x\n",
+		   map->overlay, map->overlay_prefix,
+		   map->underlay, map->underlay_prefix,
+		   overlay_mask, underlay_mask);
+
+	if ((map->overlay & ~overlay_mask) || (map->underlay & ~underlay_mask))
+		return -EINVAL;
+
+	if (!(map->overlay & overlay_mask) && (map->underlay & underlay_mask))
+		return -EINVAL;
+
+	/* Special case: overlay 0 and underlay 0: flush all mappings */
+	if (!map->overlay && !map->underlay) {
+		vxlan_fan_flush_map(vxlan);
+		return 0;
+	}
+	
+	/* Special case: overlay set and underlay 0: clear map for overlay */
+	if (!map->underlay)
+		return vxlan_fan_del_map(vxlan, map->overlay);
+
+	if (vxlan_fan_find_map(vxlan, map->overlay))
+		return -EEXIST;
+
+	fan_map = kmalloc(sizeof(*fan_map), GFP_KERNEL);
+	fan_map->underlay = map->underlay;
+	fan_map->overlay = map->overlay;
+	fan_map->underlay_prefix = map->underlay_prefix;
+	fan_map->overlay_mask = ntohl(overlay_mask);
+	fan_map->overlay_prefix = map->overlay_prefix;
+
+	list_add_tail_rcu(&fan_map->list, &vxlan->fan.fan_maps);
+
+	return 0;
+}
+	
+static int vxlan_parse_fan_map(struct nlattr *data[], struct vxlan_dev *vxlan)
+{
+	struct ifla_fan_map *map;
+	struct nlattr *attr;
+	int rem, rv;
+
+	nla_for_each_nested(attr, data[IFLA_IPTUN_FAN_MAP], rem) {
+		map = nla_data(attr);
+		rv = vxlan_fan_add_map(vxlan, map);
+		if (rv)
+			return rv;
+	}
+
+	return 0;
+}
+
+static int vxlan_fan_build_rdst(struct vxlan_dev *vxlan, struct sk_buff *skb,
+				      struct vxlan_rdst *fan_rdst)
+{
+	struct ip_fan_map *f_map;
+	union vxlan_addr *va;
+	u32 daddr, underlay;
+	struct arphdr *arp;
+	void *arp_ptr;
+	struct ethhdr *eth;
+	struct iphdr *iph;
+
+	eth = eth_hdr(skb);
+	switch (eth->h_proto) {
+	case htons(ETH_P_IP):
+		iph = ip_hdr(skb);
+		if (!iph)
+			return -EINVAL;
+		daddr = iph->daddr;
+		break;
+	case htons(ETH_P_ARP):
+		arp = arp_hdr(skb);
+		if (!arp)
+			return -EINVAL;
+		arp_ptr = arp + 1;
+		netdev_dbg(vxlan->dev,
+			   "vfbr: arp sha %pM sip %pI4 tha %pM tip %pI4\n",
+			   arp_ptr, arp_ptr + skb->dev->addr_len,
+			   arp_ptr + skb->dev->addr_len + 4,
+			   arp_ptr + (skb->dev->addr_len * 2) + 4);
+		arp_ptr += (skb->dev->addr_len * 2) + 4;
+		memcpy(&daddr, arp_ptr, 4);
+		break;
+	default:
+		netdev_dbg(vxlan->dev, "vfbr: unknown eth p %x\n", eth->h_proto);
+		return -EINVAL;
+	}
+
+	f_map = vxlan_fan_find_map(vxlan, daddr);
+	if (!f_map)
+		return -EINVAL;
+
+	daddr = ntohl(daddr);
+	underlay = ntohl(f_map->underlay);
+	if (!underlay)
+		return -EINVAL;
+
+	memset(fan_rdst, 0, sizeof(*fan_rdst));
+	va = &fan_rdst->remote_ip;
+	va->sa.sa_family = AF_INET;
+	fan_rdst->remote_vni = vxlan->default_dst.remote_vni;
+	va->sin.sin_addr.s_addr = htonl(underlay |
+					((daddr & ~f_map->overlay_mask) >>
+					 (32 - f_map->overlay_prefix -
+					  (32 - f_map->underlay_prefix))));
+	netdev_dbg(vxlan->dev, "vfbr: daddr %x ul %x dst %x\n",
+		   daddr, underlay, va->sin.sin_addr.s_addr);
+
+	return 0;
+}
+
+#if IS_ENABLED(CONFIG_IPV6)
+static inline
+bool vxlan_addr_equal(const union vxlan_addr *a, const union vxlan_addr *b)
+{
+	if (a->sa.sa_family != b->sa.sa_family)
+		return false;
+	if (a->sa.sa_family == AF_INET6)
+		return ipv6_addr_equal(&a->sin6.sin6_addr, &b->sin6.sin6_addr);
+	else
+		return a->sin.sin_addr.s_addr == b->sin.sin_addr.s_addr;
+}
+
+static int vxlan_nla_get_addr(union vxlan_addr *ip, struct nlattr *nla)
+{
+	if (nla_len(nla) >= sizeof(struct in6_addr)) {
+		ip->sin6.sin6_addr = nla_get_in6_addr(nla);
+		ip->sa.sa_family = AF_INET6;
+		return 0;
+	} else if (nla_len(nla) >= sizeof(__be32)) {
+		ip->sin.sin_addr.s_addr = nla_get_in_addr(nla);
+		ip->sa.sa_family = AF_INET;
+		return 0;
+	} else {
+		return -EAFNOSUPPORT;
+	}
+}
+
+static int vxlan_nla_put_addr(struct sk_buff *skb, int attr,
+			      const union vxlan_addr *ip)
+{
+	if (ip->sa.sa_family == AF_INET6)
+		return nla_put_in6_addr(skb, attr, &ip->sin6.sin6_addr);
+	else
+		return nla_put_in_addr(skb, attr, ip->sin.sin_addr.s_addr);
+}
+
+#else /* !CONFIG_IPV6 */
+
+static inline
+bool vxlan_addr_equal(const union vxlan_addr *a, const union vxlan_addr *b)
+{
+	return a->sin.sin_addr.s_addr == b->sin.sin_addr.s_addr;
+}
+
+static int vxlan_nla_get_addr(union vxlan_addr *ip, struct nlattr *nla)
+{
+	if (nla_len(nla) >= sizeof(struct in6_addr)) {
+		return -EAFNOSUPPORT;
+	} else if (nla_len(nla) >= sizeof(__be32)) {
+		ip->sin.sin_addr.s_addr = nla_get_in_addr(nla);
+		ip->sa.sa_family = AF_INET;
+		return 0;
+	} else {
+		return -EAFNOSUPPORT;
+	}
+}
+
+static int vxlan_nla_put_addr(struct sk_buff *skb, int attr,
+			      const union vxlan_addr *ip)
+{
+	return nla_put_in_addr(skb, attr, ip->sin.sin_addr.s_addr);
+}
+#endif
+
+/* Virtual Network hash table head */
+static inline struct hlist_head *vni_head(struct vxlan_sock *vs, __be32 vni)
+{
+	return &vs->vni_list[hash_32((__force u32)vni, VNI_HASH_BITS)];
+}
+
+/* Socket hash table head */
+static inline struct hlist_head *vs_head(struct net *net, __be16 port)
+{
+	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+
+	return &vn->sock_list[hash_32(ntohs(port), PORT_HASH_BITS)];
+}
+
+/* First remote destination for a forwarding entry.
+ * Guaranteed to be non-NULL because remotes are never deleted.
+ */
+static inline struct vxlan_rdst *first_remote_rcu(struct vxlan_fdb *fdb)
+{
+	if (rcu_access_pointer(fdb->nh))
+		return NULL;
+	return list_entry_rcu(fdb->remotes.next, struct vxlan_rdst, list);
+}
+
+static inline struct vxlan_rdst *first_remote_rtnl(struct vxlan_fdb *fdb)
+{
+	if (rcu_access_pointer(fdb->nh))
+		return NULL;
+	return list_first_entry(&fdb->remotes, struct vxlan_rdst, list);
+}
+
+/* Find VXLAN socket based on network namespace, address family, UDP port,
+ * enabled unshareable flags and socket device binding (see l3mdev with
+ * non-default VRF).
+ */
+static struct vxlan_sock *vxlan_find_sock(struct net *net, sa_family_t family,
+					  __be16 port, u32 flags, int ifindex)
+{
+	struct vxlan_sock *vs;
+
+	flags &= VXLAN_F_RCV_FLAGS;
+
+	hlist_for_each_entry_rcu(vs, vs_head(net, port), hlist) {
+		if (inet_sk(vs->sock->sk)->inet_sport == port &&
+		    vxlan_get_sk_family(vs) == family &&
+		    vs->flags == flags &&
+		    vs->sock->sk->sk_bound_dev_if == ifindex)
+			return vs;
+	}
+	return NULL;
+}
+
+static struct vxlan_dev *vxlan_vs_find_vni(struct vxlan_sock *vs, int ifindex,
+					   __be32 vni)
+{
+	struct vxlan_dev_node *node;
+
+	/* For flow based devices, map all packets to VNI 0 */
+	if (vs->flags & VXLAN_F_COLLECT_METADATA)
+		vni = 0;
+
+	hlist_for_each_entry_rcu(node, vni_head(vs, vni), hlist) {
+		if (node->vxlan->default_dst.remote_vni != vni)
+			continue;
+
+		if (IS_ENABLED(CONFIG_IPV6)) {
+			const struct vxlan_config *cfg = &node->vxlan->cfg;
+
+			if ((cfg->flags & VXLAN_F_IPV6_LINKLOCAL) &&
+			    cfg->remote_ifindex != ifindex)
+				continue;
+		}
+
+		return node->vxlan;
+	}
+
+	return NULL;
+}
+
+/* Look up VNI in a per net namespace table */
+static struct vxlan_dev *vxlan_find_vni(struct net *net, int ifindex,
+					__be32 vni, sa_family_t family,
+					__be16 port, u32 flags)
+{
+	struct vxlan_sock *vs;
+
+	vs = vxlan_find_sock(net, family, port, flags, ifindex);
+	if (!vs)
+		return NULL;
+
+	return vxlan_vs_find_vni(vs, ifindex, vni);
+}
+
+/* Fill in neighbour message in skbuff. */
+static int vxlan_fdb_info(struct sk_buff *skb, struct vxlan_dev *vxlan,
+			  const struct vxlan_fdb *fdb,
+			  u32 portid, u32 seq, int type, unsigned int flags,
+			  const struct vxlan_rdst *rdst)
+{
+	unsigned long now = jiffies;
+	struct nda_cacheinfo ci;
+	bool send_ip, send_eth;
+	struct nlmsghdr *nlh;
+	struct nexthop *nh;
+	struct ndmsg *ndm;
+	int nh_family;
+	u32 nh_id;
+
+	nlh = nlmsg_put(skb, portid, seq, type, sizeof(*ndm), flags);
+	if (nlh == NULL)
+		return -EMSGSIZE;
+
+	ndm = nlmsg_data(nlh);
+	memset(ndm, 0, sizeof(*ndm));
+
+	send_eth = send_ip = true;
+
+	rcu_read_lock();
+	nh = rcu_dereference(fdb->nh);
+	if (nh) {
+		nh_family = nexthop_get_family(nh);
+		nh_id = nh->id;
+	}
+	rcu_read_unlock();
+
+	if (type == RTM_GETNEIGH) {
+		if (rdst) {
+			send_ip = !vxlan_addr_any(&rdst->remote_ip);
+			ndm->ndm_family = send_ip ? rdst->remote_ip.sa.sa_family : AF_INET;
+		} else if (nh) {
+			ndm->ndm_family = nh_family;
+		}
+		send_eth = !is_zero_ether_addr(fdb->eth_addr);
+	} else
+		ndm->ndm_family	= AF_BRIDGE;
+	ndm->ndm_state = fdb->state;
+	ndm->ndm_ifindex = vxlan->dev->ifindex;
+	ndm->ndm_flags = fdb->flags;
+	if (rdst && rdst->offloaded)
+		ndm->ndm_flags |= NTF_OFFLOADED;
+	ndm->ndm_type = RTN_UNICAST;
+
+	if (!net_eq(dev_net(vxlan->dev), vxlan->net) &&
+	    nla_put_s32(skb, NDA_LINK_NETNSID,
+			peernet2id(dev_net(vxlan->dev), vxlan->net)))
+		goto nla_put_failure;
+
+	if (send_eth && nla_put(skb, NDA_LLADDR, ETH_ALEN, &fdb->eth_addr))
+		goto nla_put_failure;
+	if (nh) {
+		if (nla_put_u32(skb, NDA_NH_ID, nh_id))
+			goto nla_put_failure;
+	} else if (rdst) {
+		if (send_ip && vxlan_nla_put_addr(skb, NDA_DST,
+						  &rdst->remote_ip))
+			goto nla_put_failure;
+
+		if (rdst->remote_port &&
+		    rdst->remote_port != vxlan->cfg.dst_port &&
+		    nla_put_be16(skb, NDA_PORT, rdst->remote_port))
+			goto nla_put_failure;
+		if (rdst->remote_vni != vxlan->default_dst.remote_vni &&
+		    nla_put_u32(skb, NDA_VNI, be32_to_cpu(rdst->remote_vni)))
+			goto nla_put_failure;
+		if (rdst->remote_ifindex &&
+		    nla_put_u32(skb, NDA_IFINDEX, rdst->remote_ifindex))
+			goto nla_put_failure;
+	}
+
+	if ((vxlan->cfg.flags & VXLAN_F_COLLECT_METADATA) && fdb->vni &&
+	    nla_put_u32(skb, NDA_SRC_VNI,
+			be32_to_cpu(fdb->vni)))
+		goto nla_put_failure;
+
+	ci.ndm_used	 = jiffies_to_clock_t(now - fdb->used);
+	ci.ndm_confirmed = 0;
+	ci.ndm_updated	 = jiffies_to_clock_t(now - fdb->updated);
+	ci.ndm_refcnt	 = 0;
+
+	if (nla_put(skb, NDA_CACHEINFO, sizeof(ci), &ci))
+		goto nla_put_failure;
+
+	nlmsg_end(skb, nlh);
+	return 0;
+
+nla_put_failure:
+	nlmsg_cancel(skb, nlh);
+	return -EMSGSIZE;
+}
+
+static inline size_t vxlan_nlmsg_size(void)
+{
+	return NLMSG_ALIGN(sizeof(struct ndmsg))
+		+ nla_total_size(ETH_ALEN) /* NDA_LLADDR */
+		+ nla_total_size(sizeof(struct in6_addr)) /* NDA_DST */
+		+ nla_total_size(sizeof(__be16)) /* NDA_PORT */
+		+ nla_total_size(sizeof(__be32)) /* NDA_VNI */
+		+ nla_total_size(sizeof(__u32)) /* NDA_IFINDEX */
+		+ nla_total_size(sizeof(__s32)) /* NDA_LINK_NETNSID */
+		+ nla_total_size(sizeof(struct nda_cacheinfo));
+}
+
+static void __vxlan_fdb_notify(struct vxlan_dev *vxlan, struct vxlan_fdb *fdb,
+			       struct vxlan_rdst *rd, int type)
+{
+	struct net *net = dev_net(vxlan->dev);
+	struct sk_buff *skb;
+	int err = -ENOBUFS;
+
+	skb = nlmsg_new(vxlan_nlmsg_size(), GFP_ATOMIC);
+	if (skb == NULL)
+		goto errout;
+
+	err = vxlan_fdb_info(skb, vxlan, fdb, 0, 0, type, 0, rd);
+	if (err < 0) {
+		/* -EMSGSIZE implies BUG in vxlan_nlmsg_size() */
+		WARN_ON(err == -EMSGSIZE);
+		kfree_skb(skb);
+		goto errout;
+	}
+
+	rtnl_notify(skb, net, 0, RTNLGRP_NEIGH, NULL, GFP_ATOMIC);
+	return;
+errout:
+	if (err < 0)
+		rtnl_set_sk_err(net, RTNLGRP_NEIGH, err);
+}
+
+static void vxlan_fdb_switchdev_notifier_info(const struct vxlan_dev *vxlan,
+			    const struct vxlan_fdb *fdb,
+			    const struct vxlan_rdst *rd,
+			    struct netlink_ext_ack *extack,
+			    struct switchdev_notifier_vxlan_fdb_info *fdb_info)
+{
+	fdb_info->info.dev = vxlan->dev;
+	fdb_info->info.extack = extack;
+	fdb_info->remote_ip = rd->remote_ip;
+	fdb_info->remote_port = rd->remote_port;
+	fdb_info->remote_vni = rd->remote_vni;
+	fdb_info->remote_ifindex = rd->remote_ifindex;
+	memcpy(fdb_info->eth_addr, fdb->eth_addr, ETH_ALEN);
+	fdb_info->vni = fdb->vni;
+	fdb_info->offloaded = rd->offloaded;
+	fdb_info->added_by_user = fdb->flags & NTF_VXLAN_ADDED_BY_USER;
+}
+
+static int vxlan_fdb_switchdev_call_notifiers(struct vxlan_dev *vxlan,
+					      struct vxlan_fdb *fdb,
+					      struct vxlan_rdst *rd,
+					      bool adding,
+					      struct netlink_ext_ack *extack)
+{
+	struct switchdev_notifier_vxlan_fdb_info info;
+	enum switchdev_notifier_type notifier_type;
+	int ret;
+
+	if (WARN_ON(!rd))
+		return 0;
+
+	notifier_type = adding ? SWITCHDEV_VXLAN_FDB_ADD_TO_DEVICE
+			       : SWITCHDEV_VXLAN_FDB_DEL_TO_DEVICE;
+	vxlan_fdb_switchdev_notifier_info(vxlan, fdb, rd, NULL, &info);
+	ret = call_switchdev_notifiers(notifier_type, vxlan->dev,
+				       &info.info, extack);
+	return notifier_to_errno(ret);
+}
+
+static int vxlan_fdb_notify(struct vxlan_dev *vxlan, struct vxlan_fdb *fdb,
+			    struct vxlan_rdst *rd, int type, bool swdev_notify,
+			    struct netlink_ext_ack *extack)
+{
+	int err;
+
+	if (swdev_notify && rd) {
+		switch (type) {
+		case RTM_NEWNEIGH:
+			err = vxlan_fdb_switchdev_call_notifiers(vxlan, fdb, rd,
+								 true, extack);
+			if (err)
+				return err;
+			break;
+		case RTM_DELNEIGH:
+			vxlan_fdb_switchdev_call_notifiers(vxlan, fdb, rd,
+							   false, extack);
+			break;
+		}
+	}
+
+	__vxlan_fdb_notify(vxlan, fdb, rd, type);
+	return 0;
+}
+
+static void vxlan_ip_miss(struct net_device *dev, union vxlan_addr *ipa)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_fdb f = {
+		.state = NUD_STALE,
+	};
+	struct vxlan_rdst remote = {
+		.remote_ip = *ipa, /* goes to NDA_DST */
+		.remote_vni = cpu_to_be32(VXLAN_N_VID),
+	};
+
+	vxlan_fdb_notify(vxlan, &f, &remote, RTM_GETNEIGH, true, NULL);
+}
+
+static void vxlan_fdb_miss(struct vxlan_dev *vxlan, const u8 eth_addr[ETH_ALEN])
+{
+	struct vxlan_fdb f = {
+		.state = NUD_STALE,
+	};
+	struct vxlan_rdst remote = { };
+
+	memcpy(f.eth_addr, eth_addr, ETH_ALEN);
+
+	vxlan_fdb_notify(vxlan, &f, &remote, RTM_GETNEIGH, true, NULL);
+}
+
+/* Hash Ethernet address */
+static u32 eth_hash(const unsigned char *addr)
+{
+	u64 value = get_unaligned((u64 *)addr);
+
+	/* only want 6 bytes */
+#ifdef __BIG_ENDIAN
+	value >>= 16;
+#else
+	value <<= 16;
+#endif
+	return hash_64(value, FDB_HASH_BITS);
+}
+
+static u32 eth_vni_hash(const unsigned char *addr, __be32 vni)
+{
+	/* use 1 byte of OUI and 3 bytes of NIC */
+	u32 key = get_unaligned((u32 *)(addr + 2));
+
+	return jhash_2words(key, vni, vxlan_salt) & (FDB_HASH_SIZE - 1);
+}
+
+static u32 fdb_head_index(struct vxlan_dev *vxlan, const u8 *mac, __be32 vni)
+{
+	if (vxlan->cfg.flags & VXLAN_F_COLLECT_METADATA)
+		return eth_vni_hash(mac, vni);
+	else
+		return eth_hash(mac);
+}
+
+/* Hash chain to use given mac address */
+static inline struct hlist_head *vxlan_fdb_head(struct vxlan_dev *vxlan,
+						const u8 *mac, __be32 vni)
+{
+	return &vxlan->fdb_head[fdb_head_index(vxlan, mac, vni)];
+}
+
+/* Look up Ethernet address in forwarding table */
+static struct vxlan_fdb *__vxlan_find_mac(struct vxlan_dev *vxlan,
+					  const u8 *mac, __be32 vni)
+{
+	struct hlist_head *head = vxlan_fdb_head(vxlan, mac, vni);
+	struct vxlan_fdb *f;
+
+	hlist_for_each_entry_rcu(f, head, hlist) {
+		if (ether_addr_equal(mac, f->eth_addr)) {
+			if (vxlan->cfg.flags & VXLAN_F_COLLECT_METADATA) {
+				if (vni == f->vni)
+					return f;
+			} else {
+				return f;
+			}
+		}
+	}
+
+	return NULL;
+}
+
+static struct vxlan_fdb *vxlan_find_mac(struct vxlan_dev *vxlan,
+					const u8 *mac, __be32 vni)
+{
+	struct vxlan_fdb *f;
+
+	f = __vxlan_find_mac(vxlan, mac, vni);
+	if (f && f->used != jiffies)
+		f->used = jiffies;
+
+	return f;
+}
+
+/* caller should hold vxlan->hash_lock */
+static struct vxlan_rdst *vxlan_fdb_find_rdst(struct vxlan_fdb *f,
+					      union vxlan_addr *ip, __be16 port,
+					      __be32 vni, __u32 ifindex)
+{
+	struct vxlan_rdst *rd;
+
+	list_for_each_entry(rd, &f->remotes, list) {
+		if (vxlan_addr_equal(&rd->remote_ip, ip) &&
+		    rd->remote_port == port &&
+		    rd->remote_vni == vni &&
+		    rd->remote_ifindex == ifindex)
+			return rd;
+	}
+
+	return NULL;
+}
+
+int vxlan_fdb_find_uc(struct net_device *dev, const u8 *mac, __be32 vni,
+		      struct switchdev_notifier_vxlan_fdb_info *fdb_info)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	u8 eth_addr[ETH_ALEN + 2] = { 0 };
+	struct vxlan_rdst *rdst;
+	struct vxlan_fdb *f;
+	int rc = 0;
+
+	if (is_multicast_ether_addr(mac) ||
+	    is_zero_ether_addr(mac))
+		return -EINVAL;
+
+	ether_addr_copy(eth_addr, mac);
+
+	rcu_read_lock();
+
+	f = __vxlan_find_mac(vxlan, eth_addr, vni);
+	if (!f) {
+		rc = -ENOENT;
+		goto out;
+	}
+
+	rdst = first_remote_rcu(f);
+	vxlan_fdb_switchdev_notifier_info(vxlan, f, rdst, NULL, fdb_info);
+
+out:
+	rcu_read_unlock();
+	return rc;
+}
+EXPORT_SYMBOL_GPL(vxlan_fdb_find_uc);
+
+static int vxlan_fdb_notify_one(struct notifier_block *nb,
+				const struct vxlan_dev *vxlan,
+				const struct vxlan_fdb *f,
+				const struct vxlan_rdst *rdst,
+				struct netlink_ext_ack *extack)
+{
+	struct switchdev_notifier_vxlan_fdb_info fdb_info;
+	int rc;
+
+	vxlan_fdb_switchdev_notifier_info(vxlan, f, rdst, extack, &fdb_info);
+	rc = nb->notifier_call(nb, SWITCHDEV_VXLAN_FDB_ADD_TO_DEVICE,
+			       &fdb_info);
+	return notifier_to_errno(rc);
+}
+
+int vxlan_fdb_replay(const struct net_device *dev, __be32 vni,
+		     struct notifier_block *nb,
+		     struct netlink_ext_ack *extack)
+{
+	struct vxlan_dev *vxlan;
+	struct vxlan_rdst *rdst;
+	struct vxlan_fdb *f;
+	unsigned int h;
+	int rc = 0;
+
+	if (!netif_is_vxlan(dev))
+		return -EINVAL;
+	vxlan = netdev_priv(dev);
+
+	for (h = 0; h < FDB_HASH_SIZE; ++h) {
+		spin_lock_bh(&vxlan->hash_lock[h]);
+		hlist_for_each_entry(f, &vxlan->fdb_head[h], hlist) {
+			if (f->vni == vni) {
+				list_for_each_entry(rdst, &f->remotes, list) {
+					rc = vxlan_fdb_notify_one(nb, vxlan,
+								  f, rdst,
+								  extack);
+					if (rc)
+						goto unlock;
+				}
+			}
+		}
+		spin_unlock_bh(&vxlan->hash_lock[h]);
+	}
+	return 0;
+
+unlock:
+	spin_unlock_bh(&vxlan->hash_lock[h]);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(vxlan_fdb_replay);
+
+void vxlan_fdb_clear_offload(const struct net_device *dev, __be32 vni)
+{
+	struct vxlan_dev *vxlan;
+	struct vxlan_rdst *rdst;
+	struct vxlan_fdb *f;
+	unsigned int h;
+
+	if (!netif_is_vxlan(dev))
+		return;
+	vxlan = netdev_priv(dev);
+
+	for (h = 0; h < FDB_HASH_SIZE; ++h) {
+		spin_lock_bh(&vxlan->hash_lock[h]);
+		hlist_for_each_entry(f, &vxlan->fdb_head[h], hlist)
+			if (f->vni == vni)
+				list_for_each_entry(rdst, &f->remotes, list)
+					rdst->offloaded = false;
+		spin_unlock_bh(&vxlan->hash_lock[h]);
+	}
+
+}
+EXPORT_SYMBOL_GPL(vxlan_fdb_clear_offload);
+
+/* Replace destination of unicast mac */
+static int vxlan_fdb_replace(struct vxlan_fdb *f,
+			     union vxlan_addr *ip, __be16 port, __be32 vni,
+			     __u32 ifindex, struct vxlan_rdst *oldrd)
+{
+	struct vxlan_rdst *rd;
+
+	rd = vxlan_fdb_find_rdst(f, ip, port, vni, ifindex);
+	if (rd)
+		return 0;
+
+	rd = list_first_entry_or_null(&f->remotes, struct vxlan_rdst, list);
+	if (!rd)
+		return 0;
+
+	*oldrd = *rd;
+	dst_cache_reset(&rd->dst_cache);
+	rd->remote_ip = *ip;
+	rd->remote_port = port;
+	rd->remote_vni = vni;
+	rd->remote_ifindex = ifindex;
+	rd->offloaded = false;
+	return 1;
+}
+
+/* Add/update destinations for multicast */
+static int vxlan_fdb_append(struct vxlan_fdb *f,
+			    union vxlan_addr *ip, __be16 port, __be32 vni,
+			    __u32 ifindex, struct vxlan_rdst **rdp)
+{
+	struct vxlan_rdst *rd;
+
+	rd = vxlan_fdb_find_rdst(f, ip, port, vni, ifindex);
+	if (rd)
+		return 0;
+
+	rd = kmalloc(sizeof(*rd), GFP_ATOMIC);
+	if (rd == NULL)
+		return -ENOMEM;
+
+	if (dst_cache_init(&rd->dst_cache, GFP_ATOMIC)) {
+		kfree(rd);
+		return -ENOMEM;
+	}
+
+	rd->remote_ip = *ip;
+	rd->remote_port = port;
+	rd->offloaded = false;
+	rd->remote_vni = vni;
+	rd->remote_ifindex = ifindex;
+
+	list_add_tail_rcu(&rd->list, &f->remotes);
+
+	*rdp = rd;
+	return 1;
+}
+
+static bool vxlan_parse_gpe_proto(struct vxlanhdr *hdr, __be16 *protocol)
+{
+	struct vxlanhdr_gpe *gpe = (struct vxlanhdr_gpe *)hdr;
+
+	/* Need to have Next Protocol set for interfaces in GPE mode. */
+	if (!gpe->np_applied)
+		return false;
+	/* "The initial version is 0. If a receiver does not support the
+	 * version indicated it MUST drop the packet.
+	 */
+	if (gpe->version != 0)
+		return false;
+	/* "When the O bit is set to 1, the packet is an OAM packet and OAM
+	 * processing MUST occur." However, we don't implement OAM
+	 * processing, thus drop the packet.
+	 */
+	if (gpe->oam_flag)
+		return false;
+
+	*protocol = tun_p_to_eth_p(gpe->next_protocol);
+	if (!*protocol)
+		return false;
+
+	return true;
+}
+
+static struct vxlanhdr *vxlan_gro_remcsum(struct sk_buff *skb,
+					  unsigned int off,
+					  struct vxlanhdr *vh, size_t hdrlen,
+					  __be32 vni_field,
+					  struct gro_remcsum *grc,
+					  bool nopartial)
+{
+	size_t start, offset;
+
+	if (skb->remcsum_offload)
+		return vh;
+
+	if (!NAPI_GRO_CB(skb)->csum_valid)
+		return NULL;
+
+	start = vxlan_rco_start(vni_field);
+	offset = start + vxlan_rco_offset(vni_field);
+
+	vh = skb_gro_remcsum_process(skb, (void *)vh, off, hdrlen,
+				     start, offset, grc, nopartial);
+
+	skb->remcsum_offload = 1;
+
+	return vh;
+}
+
+static struct sk_buff *vxlan_gro_receive(struct sock *sk,
+					 struct list_head *head,
+					 struct sk_buff *skb)
+{
+	struct sk_buff *pp = NULL;
+	struct sk_buff *p;
+	struct vxlanhdr *vh, *vh2;
+	unsigned int hlen, off_vx;
+	int flush = 1;
+	struct vxlan_sock *vs = rcu_dereference_sk_user_data(sk);
+	__be32 flags;
+	struct gro_remcsum grc;
+
+	skb_gro_remcsum_init(&grc);
+
+	off_vx = skb_gro_offset(skb);
+	hlen = off_vx + sizeof(*vh);
+	vh   = skb_gro_header_fast(skb, off_vx);
+	if (skb_gro_header_hard(skb, hlen)) {
+		vh = skb_gro_header_slow(skb, hlen, off_vx);
+		if (unlikely(!vh))
+			goto out;
+	}
+
+	skb_gro_postpull_rcsum(skb, vh, sizeof(struct vxlanhdr));
+
+	flags = vh->vx_flags;
+
+	if ((flags & VXLAN_HF_RCO) && (vs->flags & VXLAN_F_REMCSUM_RX)) {
+		vh = vxlan_gro_remcsum(skb, off_vx, vh, sizeof(struct vxlanhdr),
+				       vh->vx_vni, &grc,
+				       !!(vs->flags &
+					  VXLAN_F_REMCSUM_NOPARTIAL));
+
+		if (!vh)
+			goto out;
+	}
+
+	skb_gro_pull(skb, sizeof(struct vxlanhdr)); /* pull vxlan header */
+
+	list_for_each_entry(p, head, list) {
+		if (!NAPI_GRO_CB(p)->same_flow)
+			continue;
+
+		vh2 = (struct vxlanhdr *)(p->data + off_vx);
+		if (vh->vx_flags != vh2->vx_flags ||
+		    vh->vx_vni != vh2->vx_vni) {
+			NAPI_GRO_CB(p)->same_flow = 0;
+			continue;
+		}
+	}
+
+	pp = call_gro_receive(eth_gro_receive, head, skb);
+	flush = 0;
+
+out:
+	skb_gro_flush_final_remcsum(skb, pp, flush, &grc);
+
+	return pp;
+}
+
+static int vxlan_gro_complete(struct sock *sk, struct sk_buff *skb, int nhoff)
+{
+	/* Sets 'skb->inner_mac_header' since we are always called with
+	 * 'skb->encapsulation' set.
+	 */
+	return eth_gro_complete(skb, nhoff + sizeof(struct vxlanhdr));
+}
+
+static struct vxlan_fdb *vxlan_fdb_alloc(struct vxlan_dev *vxlan, const u8 *mac,
+					 __u16 state, __be32 src_vni,
+					 __u16 ndm_flags)
+{
+	struct vxlan_fdb *f;
+
+	f = kmalloc(sizeof(*f), GFP_ATOMIC);
+	if (!f)
+		return NULL;
+	f->state = state;
+	f->flags = ndm_flags;
+	f->updated = f->used = jiffies;
+	f->vni = src_vni;
+	f->nh = NULL;
+	RCU_INIT_POINTER(f->vdev, vxlan);
+	INIT_LIST_HEAD(&f->nh_list);
+	INIT_LIST_HEAD(&f->remotes);
+	memcpy(f->eth_addr, mac, ETH_ALEN);
+
+	return f;
+}
+
+static void vxlan_fdb_insert(struct vxlan_dev *vxlan, const u8 *mac,
+			     __be32 src_vni, struct vxlan_fdb *f)
+{
+	++vxlan->addrcnt;
+	hlist_add_head_rcu(&f->hlist,
+			   vxlan_fdb_head(vxlan, mac, src_vni));
+}
+
+static int vxlan_fdb_nh_update(struct vxlan_dev *vxlan, struct vxlan_fdb *fdb,
+			       u32 nhid, struct netlink_ext_ack *extack)
+{
+	struct nexthop *old_nh = rtnl_dereference(fdb->nh);
+	struct nexthop *nh;
+	int err = -EINVAL;
+
+	if (old_nh && old_nh->id == nhid)
+		return 0;
+
+	nh = nexthop_find_by_id(vxlan->net, nhid);
+	if (!nh) {
+		NL_SET_ERR_MSG(extack, "Nexthop id does not exist");
+		goto err_inval;
+	}
+
+	if (nh) {
+		if (!nexthop_get(nh)) {
+			NL_SET_ERR_MSG(extack, "Nexthop has been deleted");
+			nh = NULL;
+			goto err_inval;
+		}
+		if (!nexthop_is_fdb(nh)) {
+			NL_SET_ERR_MSG(extack, "Nexthop is not a fdb nexthop");
+			goto err_inval;
+		}
+
+		if (!nexthop_is_multipath(nh)) {
+			NL_SET_ERR_MSG(extack, "Nexthop is not a multipath group");
+			goto err_inval;
+		}
+
+		/* check nexthop group family */
+		switch (vxlan->default_dst.remote_ip.sa.sa_family) {
+		case AF_INET:
+			if (!nexthop_has_v4(nh)) {
+				err = -EAFNOSUPPORT;
+				NL_SET_ERR_MSG(extack, "Nexthop group family not supported");
+				goto err_inval;
+			}
+			break;
+		case AF_INET6:
+			if (nexthop_has_v4(nh)) {
+				err = -EAFNOSUPPORT;
+				NL_SET_ERR_MSG(extack, "Nexthop group family not supported");
+				goto err_inval;
+			}
+		}
+	}
+
+	if (old_nh) {
+		list_del_rcu(&fdb->nh_list);
+		nexthop_put(old_nh);
+	}
+	rcu_assign_pointer(fdb->nh, nh);
+	list_add_tail_rcu(&fdb->nh_list, &nh->fdb_list);
+	return 1;
+
+err_inval:
+	if (nh)
+		nexthop_put(nh);
+	return err;
+}
+
+static int vxlan_fdb_create(struct vxlan_dev *vxlan,
+			    const u8 *mac, union vxlan_addr *ip,
+			    __u16 state, __be16 port, __be32 src_vni,
+			    __be32 vni, __u32 ifindex, __u16 ndm_flags,
+			    u32 nhid, struct vxlan_fdb **fdb,
+			    struct netlink_ext_ack *extack)
+{
+	struct vxlan_rdst *rd = NULL;
+	struct vxlan_fdb *f;
+	int rc;
+
+	if (vxlan->cfg.addrmax &&
+	    vxlan->addrcnt >= vxlan->cfg.addrmax)
+		return -ENOSPC;
+
+	netdev_dbg(vxlan->dev, "add %pM -> %pIS\n", mac, ip);
+	f = vxlan_fdb_alloc(vxlan, mac, state, src_vni, ndm_flags);
+	if (!f)
+		return -ENOMEM;
+
+	if (nhid)
+		rc = vxlan_fdb_nh_update(vxlan, f, nhid, extack);
+	else
+		rc = vxlan_fdb_append(f, ip, port, vni, ifindex, &rd);
+	if (rc < 0)
+		goto errout;
+
+	*fdb = f;
+
+	return 0;
+
+errout:
+	kfree(f);
+	return rc;
+}
+
+static void __vxlan_fdb_free(struct vxlan_fdb *f)
+{
+	struct vxlan_rdst *rd, *nd;
+	struct nexthop *nh;
+
+	nh = rcu_dereference_raw(f->nh);
+	if (nh) {
+		rcu_assign_pointer(f->nh, NULL);
+		rcu_assign_pointer(f->vdev, NULL);
+		nexthop_put(nh);
+	}
+
+	list_for_each_entry_safe(rd, nd, &f->remotes, list) {
+		dst_cache_destroy(&rd->dst_cache);
+		kfree(rd);
+	}
+	kfree(f);
+}
+
+static void vxlan_fdb_free(struct rcu_head *head)
+{
+	struct vxlan_fdb *f = container_of(head, struct vxlan_fdb, rcu);
+
+	__vxlan_fdb_free(f);
+}
+
+static void vxlan_fdb_destroy(struct vxlan_dev *vxlan, struct vxlan_fdb *f,
+			      bool do_notify, bool swdev_notify)
+{
+	struct vxlan_rdst *rd;
+
+	netdev_dbg(vxlan->dev, "delete %pM\n", f->eth_addr);
+
+	--vxlan->addrcnt;
+	if (do_notify) {
+		if (rcu_access_pointer(f->nh))
+			vxlan_fdb_notify(vxlan, f, NULL, RTM_DELNEIGH,
+					 swdev_notify, NULL);
+		else
+			list_for_each_entry(rd, &f->remotes, list)
+				vxlan_fdb_notify(vxlan, f, rd, RTM_DELNEIGH,
+						 swdev_notify, NULL);
+	}
+
+	hlist_del_rcu(&f->hlist);
+	list_del_rcu(&f->nh_list);
+	call_rcu(&f->rcu, vxlan_fdb_free);
+}
+
+static void vxlan_dst_free(struct rcu_head *head)
+{
+	struct vxlan_rdst *rd = container_of(head, struct vxlan_rdst, rcu);
+
+	dst_cache_destroy(&rd->dst_cache);
+	kfree(rd);
+}
+
+static int vxlan_fdb_update_existing(struct vxlan_dev *vxlan,
+				     union vxlan_addr *ip,
+				     __u16 state, __u16 flags,
+				     __be16 port, __be32 vni,
+				     __u32 ifindex, __u16 ndm_flags,
+				     struct vxlan_fdb *f, u32 nhid,
+				     bool swdev_notify,
+				     struct netlink_ext_ack *extack)
+{
+	__u16 fdb_flags = (ndm_flags & ~NTF_USE);
+	struct vxlan_rdst *rd = NULL;
+	struct vxlan_rdst oldrd;
+	int notify = 0;
+	int rc = 0;
+	int err;
+
+	if (nhid && !rcu_access_pointer(f->nh)) {
+		NL_SET_ERR_MSG(extack,
+			       "Cannot replace an existing non nexthop fdb with a nexthop");
+		return -EOPNOTSUPP;
+	}
+
+	if (nhid && (flags & NLM_F_APPEND)) {
+		NL_SET_ERR_MSG(extack,
+			       "Cannot append to a nexthop fdb");
+		return -EOPNOTSUPP;
+	}
+
+	/* Do not allow an externally learned entry to take over an entry added
+	 * by the user.
+	 */
+	if (!(fdb_flags & NTF_EXT_LEARNED) ||
+	    !(f->flags & NTF_VXLAN_ADDED_BY_USER)) {
+		if (f->state != state) {
+			f->state = state;
+			f->updated = jiffies;
+			notify = 1;
+		}
+		if (f->flags != fdb_flags) {
+			f->flags = fdb_flags;
+			f->updated = jiffies;
+			notify = 1;
+		}
+	}
+
+	if ((flags & NLM_F_REPLACE)) {
+		/* Only change unicasts */
+		if (!(is_multicast_ether_addr(f->eth_addr) ||
+		      is_zero_ether_addr(f->eth_addr))) {
+			if (nhid) {
+				rc = vxlan_fdb_nh_update(vxlan, f, nhid, extack);
+				if (rc < 0)
+					return rc;
+			} else {
+				rc = vxlan_fdb_replace(f, ip, port, vni,
+						       ifindex, &oldrd);
+			}
+			notify |= rc;
+		} else {
+			NL_SET_ERR_MSG(extack, "Cannot replace non-unicast fdb entries");
+			return -EOPNOTSUPP;
+		}
+	}
+	if ((flags & NLM_F_APPEND) &&
+	    (is_multicast_ether_addr(f->eth_addr) ||
+	     is_zero_ether_addr(f->eth_addr))) {
+		rc = vxlan_fdb_append(f, ip, port, vni, ifindex, &rd);
+
+		if (rc < 0)
+			return rc;
+		notify |= rc;
+	}
+
+	if (ndm_flags & NTF_USE)
+		f->used = jiffies;
+
+	if (notify) {
+		if (rd == NULL)
+			rd = first_remote_rtnl(f);
+
+		err = vxlan_fdb_notify(vxlan, f, rd, RTM_NEWNEIGH,
+				       swdev_notify, extack);
+		if (err)
+			goto err_notify;
+	}
+
+	return 0;
+
+err_notify:
+	if (nhid)
+		return err;
+	if ((flags & NLM_F_REPLACE) && rc)
+		*rd = oldrd;
+	else if ((flags & NLM_F_APPEND) && rc) {
+		list_del_rcu(&rd->list);
+		call_rcu(&rd->rcu, vxlan_dst_free);
+	}
+	return err;
+}
+
+static int vxlan_fdb_update_create(struct vxlan_dev *vxlan,
+				   const u8 *mac, union vxlan_addr *ip,
+				   __u16 state, __u16 flags,
+				   __be16 port, __be32 src_vni, __be32 vni,
+				   __u32 ifindex, __u16 ndm_flags, u32 nhid,
+				   bool swdev_notify,
+				   struct netlink_ext_ack *extack)
+{
+	__u16 fdb_flags = (ndm_flags & ~NTF_USE);
+	struct vxlan_fdb *f;
+	int rc;
+
+	/* Disallow replace to add a multicast entry */
+	if ((flags & NLM_F_REPLACE) &&
+	    (is_multicast_ether_addr(mac) || is_zero_ether_addr(mac)))
+		return -EOPNOTSUPP;
+
+	netdev_dbg(vxlan->dev, "add %pM -> %pIS\n", mac, ip);
+	rc = vxlan_fdb_create(vxlan, mac, ip, state, port, src_vni,
+			      vni, ifindex, fdb_flags, nhid, &f, extack);
+	if (rc < 0)
+		return rc;
+
+	vxlan_fdb_insert(vxlan, mac, src_vni, f);
+	rc = vxlan_fdb_notify(vxlan, f, first_remote_rtnl(f), RTM_NEWNEIGH,
+			      swdev_notify, extack);
+	if (rc)
+		goto err_notify;
+
+	return 0;
+
+err_notify:
+	vxlan_fdb_destroy(vxlan, f, false, false);
+	return rc;
+}
+
+/* Add new entry to forwarding table -- assumes lock held */
+static int vxlan_fdb_update(struct vxlan_dev *vxlan,
+			    const u8 *mac, union vxlan_addr *ip,
+			    __u16 state, __u16 flags,
+			    __be16 port, __be32 src_vni, __be32 vni,
+			    __u32 ifindex, __u16 ndm_flags, u32 nhid,
+			    bool swdev_notify,
+			    struct netlink_ext_ack *extack)
+{
+	struct vxlan_fdb *f;
+
+	f = __vxlan_find_mac(vxlan, mac, src_vni);
+	if (f) {
+		if (flags & NLM_F_EXCL) {
+			netdev_dbg(vxlan->dev,
+				   "lost race to create %pM\n", mac);
+			return -EEXIST;
+		}
+
+		return vxlan_fdb_update_existing(vxlan, ip, state, flags, port,
+						 vni, ifindex, ndm_flags, f,
+						 nhid, swdev_notify, extack);
+	} else {
+		if (!(flags & NLM_F_CREATE))
+			return -ENOENT;
+
+		return vxlan_fdb_update_create(vxlan, mac, ip, state, flags,
+					       port, src_vni, vni, ifindex,
+					       ndm_flags, nhid, swdev_notify,
+					       extack);
+	}
+}
+
+static void vxlan_fdb_dst_destroy(struct vxlan_dev *vxlan, struct vxlan_fdb *f,
+				  struct vxlan_rdst *rd, bool swdev_notify)
+{
+	list_del_rcu(&rd->list);
+	vxlan_fdb_notify(vxlan, f, rd, RTM_DELNEIGH, swdev_notify, NULL);
+	call_rcu(&rd->rcu, vxlan_dst_free);
+}
+
+static int vxlan_fdb_parse(struct nlattr *tb[], struct vxlan_dev *vxlan,
+			   union vxlan_addr *ip, __be16 *port, __be32 *src_vni,
+			   __be32 *vni, u32 *ifindex, u32 *nhid)
+{
+	struct net *net = dev_net(vxlan->dev);
+	int err;
+
+	if (tb[NDA_NH_ID] && (tb[NDA_DST] || tb[NDA_VNI] || tb[NDA_IFINDEX] ||
+	    tb[NDA_PORT]))
+		return -EINVAL;
+
+	if (tb[NDA_DST]) {
+		err = vxlan_nla_get_addr(ip, tb[NDA_DST]);
+		if (err)
+			return err;
+	} else {
+		union vxlan_addr *remote = &vxlan->default_dst.remote_ip;
+
+		if (remote->sa.sa_family == AF_INET) {
+			ip->sin.sin_addr.s_addr = htonl(INADDR_ANY);
+			ip->sa.sa_family = AF_INET;
+#if IS_ENABLED(CONFIG_IPV6)
+		} else {
+			ip->sin6.sin6_addr = in6addr_any;
+			ip->sa.sa_family = AF_INET6;
+#endif
+		}
+	}
+
+	if (tb[NDA_PORT]) {
+		if (nla_len(tb[NDA_PORT]) != sizeof(__be16))
+			return -EINVAL;
+		*port = nla_get_be16(tb[NDA_PORT]);
+	} else {
+		*port = vxlan->cfg.dst_port;
+	}
+
+	if (tb[NDA_VNI]) {
+		if (nla_len(tb[NDA_VNI]) != sizeof(u32))
+			return -EINVAL;
+		*vni = cpu_to_be32(nla_get_u32(tb[NDA_VNI]));
+	} else {
+		*vni = vxlan->default_dst.remote_vni;
+	}
+
+	if (tb[NDA_SRC_VNI]) {
+		if (nla_len(tb[NDA_SRC_VNI]) != sizeof(u32))
+			return -EINVAL;
+		*src_vni = cpu_to_be32(nla_get_u32(tb[NDA_SRC_VNI]));
+	} else {
+		*src_vni = vxlan->default_dst.remote_vni;
+	}
+
+	if (tb[NDA_IFINDEX]) {
+		struct net_device *tdev;
+
+		if (nla_len(tb[NDA_IFINDEX]) != sizeof(u32))
+			return -EINVAL;
+		*ifindex = nla_get_u32(tb[NDA_IFINDEX]);
+		tdev = __dev_get_by_index(net, *ifindex);
+		if (!tdev)
+			return -EADDRNOTAVAIL;
+	} else {
+		*ifindex = 0;
+	}
+
+	if (tb[NDA_NH_ID])
+		*nhid = nla_get_u32(tb[NDA_NH_ID]);
+	else
+		*nhid = 0;
+
+	return 0;
+}
+
+/* Add static entry (via netlink) */
+static int vxlan_fdb_add(struct ndmsg *ndm, struct nlattr *tb[],
+			 struct net_device *dev,
+			 const unsigned char *addr, u16 vid, u16 flags,
+			 struct netlink_ext_ack *extack)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	/* struct net *net = dev_net(vxlan->dev); */
+	union vxlan_addr ip;
+	__be16 port;
+	__be32 src_vni, vni;
+	u32 ifindex, nhid;
+	u32 hash_index;
+	int err;
+
+	if (!(ndm->ndm_state & (NUD_PERMANENT|NUD_REACHABLE))) {
+		pr_info("RTM_NEWNEIGH with invalid state %#x\n",
+			ndm->ndm_state);
+		return -EINVAL;
+	}
+
+	if (!tb || (!tb[NDA_DST] && !tb[NDA_NH_ID]))
+		return -EINVAL;
+
+	err = vxlan_fdb_parse(tb, vxlan, &ip, &port, &src_vni, &vni, &ifindex,
+			      &nhid);
+	if (err)
+		return err;
+
+	if (vxlan->default_dst.remote_ip.sa.sa_family != ip.sa.sa_family)
+		return -EAFNOSUPPORT;
+
+	hash_index = fdb_head_index(vxlan, addr, src_vni);
+	spin_lock_bh(&vxlan->hash_lock[hash_index]);
+	err = vxlan_fdb_update(vxlan, addr, &ip, ndm->ndm_state, flags,
+			       port, src_vni, vni, ifindex,
+			       ndm->ndm_flags | NTF_VXLAN_ADDED_BY_USER,
+			       nhid, true, extack);
+	spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+
+	return err;
+}
+
+static int __vxlan_fdb_delete(struct vxlan_dev *vxlan,
+			      const unsigned char *addr, union vxlan_addr ip,
+			      __be16 port, __be32 src_vni, __be32 vni,
+			      u32 ifindex, bool swdev_notify)
+{
+	struct vxlan_rdst *rd = NULL;
+	struct vxlan_fdb *f;
+	int err = -ENOENT;
+
+	f = vxlan_find_mac(vxlan, addr, src_vni);
+	if (!f)
+		return err;
+
+	if (!vxlan_addr_any(&ip)) {
+		rd = vxlan_fdb_find_rdst(f, &ip, port, vni, ifindex);
+		if (!rd)
+			goto out;
+	}
+
+	/* remove a destination if it's not the only one on the list,
+	 * otherwise destroy the fdb entry
+	 */
+	if (rd && !list_is_singular(&f->remotes)) {
+		vxlan_fdb_dst_destroy(vxlan, f, rd, swdev_notify);
+		goto out;
+	}
+
+	vxlan_fdb_destroy(vxlan, f, true, swdev_notify);
+
+out:
+	return 0;
+}
+
+/* Delete entry (via netlink) */
+static int vxlan_fdb_delete(struct ndmsg *ndm, struct nlattr *tb[],
+			    struct net_device *dev,
+			    const unsigned char *addr, u16 vid)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	union vxlan_addr ip;
+	__be32 src_vni, vni;
+	u32 ifindex, nhid;
+	u32 hash_index;
+	__be16 port;
+	int err;
+
+	err = vxlan_fdb_parse(tb, vxlan, &ip, &port, &src_vni, &vni, &ifindex,
+			      &nhid);
+	if (err)
+		return err;
+
+	hash_index = fdb_head_index(vxlan, addr, src_vni);
+	spin_lock_bh(&vxlan->hash_lock[hash_index]);
+	err = __vxlan_fdb_delete(vxlan, addr, ip, port, src_vni, vni, ifindex,
+				 true);
+	spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+
+	return err;
+}
+
+/* Dump forwarding table */
+static int vxlan_fdb_dump(struct sk_buff *skb, struct netlink_callback *cb,
+			  struct net_device *dev,
+			  struct net_device *filter_dev, int *idx)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	unsigned int h;
+	int err = 0;
+
+	for (h = 0; h < FDB_HASH_SIZE; ++h) {
+		struct vxlan_fdb *f;
+
+		rcu_read_lock();
+		hlist_for_each_entry_rcu(f, &vxlan->fdb_head[h], hlist) {
+			struct vxlan_rdst *rd;
+
+			if (rcu_access_pointer(f->nh)) {
+				if (*idx < cb->args[2])
+					goto skip_nh;
+				err = vxlan_fdb_info(skb, vxlan, f,
+						     NETLINK_CB(cb->skb).portid,
+						     cb->nlh->nlmsg_seq,
+						     RTM_NEWNEIGH,
+						     NLM_F_MULTI, NULL);
+				if (err < 0) {
+					rcu_read_unlock();
+					goto out;
+				}
+skip_nh:
+				*idx += 1;
+				continue;
+			}
+
+			list_for_each_entry_rcu(rd, &f->remotes, list) {
+				if (*idx < cb->args[2])
+					goto skip;
+
+				err = vxlan_fdb_info(skb, vxlan, f,
+						     NETLINK_CB(cb->skb).portid,
+						     cb->nlh->nlmsg_seq,
+						     RTM_NEWNEIGH,
+						     NLM_F_MULTI, rd);
+				if (err < 0) {
+					rcu_read_unlock();
+					goto out;
+				}
+skip:
+				*idx += 1;
+			}
+		}
+		rcu_read_unlock();
+	}
+out:
+	return err;
+}
+
+static int vxlan_fdb_get(struct sk_buff *skb,
+			 struct nlattr *tb[],
+			 struct net_device *dev,
+			 const unsigned char *addr,
+			 u16 vid, u32 portid, u32 seq,
+			 struct netlink_ext_ack *extack)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_fdb *f;
+	__be32 vni;
+	int err;
+
+	if (tb[NDA_VNI])
+		vni = cpu_to_be32(nla_get_u32(tb[NDA_VNI]));
+	else
+		vni = vxlan->default_dst.remote_vni;
+
+	rcu_read_lock();
+
+	f = __vxlan_find_mac(vxlan, addr, vni);
+	if (!f) {
+		NL_SET_ERR_MSG(extack, "Fdb entry not found");
+		err = -ENOENT;
+		goto errout;
+	}
+
+	err = vxlan_fdb_info(skb, vxlan, f, portid, seq,
+			     RTM_NEWNEIGH, 0, first_remote_rcu(f));
+errout:
+	rcu_read_unlock();
+	return err;
+}
+
+/* Watch incoming packets to learn mapping between Ethernet address
+ * and Tunnel endpoint.
+ * Return true if packet is bogus and should be dropped.
+ */
+static bool vxlan_snoop(struct net_device *dev,
+			union vxlan_addr *src_ip, const u8 *src_mac,
+			u32 src_ifindex, __be32 vni)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_fdb *f;
+	u32 ifindex = 0;
+
+	/* Ignore packets from invalid src-address */
+	if (!is_valid_ether_addr(src_mac))
+		return true;
+
+#if IS_ENABLED(CONFIG_IPV6)
+	if (src_ip->sa.sa_family == AF_INET6 &&
+	    (ipv6_addr_type(&src_ip->sin6.sin6_addr) & IPV6_ADDR_LINKLOCAL))
+		ifindex = src_ifindex;
+#endif
+
+	f = vxlan_find_mac(vxlan, src_mac, vni);
+	if (likely(f)) {
+		struct vxlan_rdst *rdst = first_remote_rcu(f);
+
+		if (likely(vxlan_addr_equal(&rdst->remote_ip, src_ip) &&
+			   rdst->remote_ifindex == ifindex))
+			return false;
+
+		/* Don't migrate static entries, drop packets */
+		if (f->state & (NUD_PERMANENT | NUD_NOARP))
+			return true;
+
+		/* Don't override an fdb with nexthop with a learnt entry */
+		if (rcu_access_pointer(f->nh))
+			return true;
+
+		if (net_ratelimit())
+			netdev_info(dev,
+				    "%pM migrated from %pIS to %pIS\n",
+				    src_mac, &rdst->remote_ip.sa, &src_ip->sa);
+
+		rdst->remote_ip = *src_ip;
+		f->updated = jiffies;
+		vxlan_fdb_notify(vxlan, f, rdst, RTM_NEWNEIGH, true, NULL);
+	} else {
+		u32 hash_index = fdb_head_index(vxlan, src_mac, vni);
+
+		/* learned new entry */
+		spin_lock(&vxlan->hash_lock[hash_index]);
+
+		/* close off race between vxlan_flush and incoming packets */
+		if (netif_running(dev))
+			vxlan_fdb_update(vxlan, src_mac, src_ip,
+					 NUD_REACHABLE,
+					 NLM_F_EXCL|NLM_F_CREATE,
+					 vxlan->cfg.dst_port,
+					 vni,
+					 vxlan->default_dst.remote_vni,
+					 ifindex, NTF_SELF, 0, true, NULL);
+		spin_unlock(&vxlan->hash_lock[hash_index]);
+	}
+
+	return false;
+}
+
+/* See if multicast group is already in use by other ID */
+static bool vxlan_group_used(struct vxlan_net *vn, struct vxlan_dev *dev)
+{
+	struct vxlan_dev *vxlan;
+	struct vxlan_sock *sock4;
+#if IS_ENABLED(CONFIG_IPV6)
+	struct vxlan_sock *sock6;
+#endif
+	unsigned short family = dev->default_dst.remote_ip.sa.sa_family;
+
+	sock4 = rtnl_dereference(dev->vn4_sock);
+
+	/* The vxlan_sock is only used by dev, leaving group has
+	 * no effect on other vxlan devices.
+	 */
+	if (family == AF_INET && sock4 && refcount_read(&sock4->refcnt) == 1)
+		return false;
+#if IS_ENABLED(CONFIG_IPV6)
+	sock6 = rtnl_dereference(dev->vn6_sock);
+	if (family == AF_INET6 && sock6 && refcount_read(&sock6->refcnt) == 1)
+		return false;
+#endif
+
+	list_for_each_entry(vxlan, &vn->vxlan_list, next) {
+		if (!netif_running(vxlan->dev) || vxlan == dev)
+			continue;
+
+		if (family == AF_INET &&
+		    rtnl_dereference(vxlan->vn4_sock) != sock4)
+			continue;
+#if IS_ENABLED(CONFIG_IPV6)
+		if (family == AF_INET6 &&
+		    rtnl_dereference(vxlan->vn6_sock) != sock6)
+			continue;
+#endif
+
+		if (!vxlan_addr_equal(&vxlan->default_dst.remote_ip,
+				      &dev->default_dst.remote_ip))
+			continue;
+
+		if (vxlan->default_dst.remote_ifindex !=
+		    dev->default_dst.remote_ifindex)
+			continue;
+
+		return true;
+	}
+
+	return false;
+}
+
+static bool __vxlan_sock_release_prep(struct vxlan_sock *vs)
+{
+	struct vxlan_net *vn;
+
+	if (!vs)
+		return false;
+	if (!refcount_dec_and_test(&vs->refcnt))
+		return false;
+
+	vn = net_generic(sock_net(vs->sock->sk), vxlan_net_id);
+	spin_lock(&vn->sock_lock);
+	hlist_del_rcu(&vs->hlist);
+	udp_tunnel_notify_del_rx_port(vs->sock,
+				      (vs->flags & VXLAN_F_GPE) ?
+				      UDP_TUNNEL_TYPE_VXLAN_GPE :
+				      UDP_TUNNEL_TYPE_VXLAN);
+	spin_unlock(&vn->sock_lock);
+
+	return true;
+}
+
+static void vxlan_sock_release(struct vxlan_dev *vxlan)
+{
+	struct vxlan_sock *sock4 = rtnl_dereference(vxlan->vn4_sock);
+#if IS_ENABLED(CONFIG_IPV6)
+	struct vxlan_sock *sock6 = rtnl_dereference(vxlan->vn6_sock);
+
+	RCU_INIT_POINTER(vxlan->vn6_sock, NULL);
+#endif
+
+	RCU_INIT_POINTER(vxlan->vn4_sock, NULL);
+	synchronize_net();
+
+	vxlan_vs_del_dev(vxlan);
+
+	if (__vxlan_sock_release_prep(sock4)) {
+		udp_tunnel_sock_release(sock4->sock);
+		kfree(sock4);
+	}
+
+#if IS_ENABLED(CONFIG_IPV6)
+	if (__vxlan_sock_release_prep(sock6)) {
+		udp_tunnel_sock_release(sock6->sock);
+		kfree(sock6);
+	}
+#endif
+}
+
+/* Update multicast group membership when first VNI on
+ * multicast address is brought up
+ */
+static int vxlan_igmp_join(struct vxlan_dev *vxlan)
+{
+	struct sock *sk;
+	union vxlan_addr *ip = &vxlan->default_dst.remote_ip;
+	int ifindex = vxlan->default_dst.remote_ifindex;
+	int ret = -EINVAL;
+
+	if (ip->sa.sa_family == AF_INET) {
+		struct vxlan_sock *sock4 = rtnl_dereference(vxlan->vn4_sock);
+		struct ip_mreqn mreq = {
+			.imr_multiaddr.s_addr	= ip->sin.sin_addr.s_addr,
+			.imr_ifindex		= ifindex,
+		};
+
+		sk = sock4->sock->sk;
+		lock_sock(sk);
+		ret = ip_mc_join_group(sk, &mreq);
+		release_sock(sk);
+#if IS_ENABLED(CONFIG_IPV6)
+	} else {
+		struct vxlan_sock *sock6 = rtnl_dereference(vxlan->vn6_sock);
+
+		sk = sock6->sock->sk;
+		lock_sock(sk);
+		ret = ipv6_stub->ipv6_sock_mc_join(sk, ifindex,
+						   &ip->sin6.sin6_addr);
+		release_sock(sk);
+#endif
+	}
+
+	return ret;
+}
+
+/* Inverse of vxlan_igmp_join when last VNI is brought down */
+static int vxlan_igmp_leave(struct vxlan_dev *vxlan)
+{
+	struct sock *sk;
+	union vxlan_addr *ip = &vxlan->default_dst.remote_ip;
+	int ifindex = vxlan->default_dst.remote_ifindex;
+	int ret = -EINVAL;
+
+	if (ip->sa.sa_family == AF_INET) {
+		struct vxlan_sock *sock4 = rtnl_dereference(vxlan->vn4_sock);
+		struct ip_mreqn mreq = {
+			.imr_multiaddr.s_addr	= ip->sin.sin_addr.s_addr,
+			.imr_ifindex		= ifindex,
+		};
+
+		sk = sock4->sock->sk;
+		lock_sock(sk);
+		ret = ip_mc_leave_group(sk, &mreq);
+		release_sock(sk);
+#if IS_ENABLED(CONFIG_IPV6)
+	} else {
+		struct vxlan_sock *sock6 = rtnl_dereference(vxlan->vn6_sock);
+
+		sk = sock6->sock->sk;
+		lock_sock(sk);
+		ret = ipv6_stub->ipv6_sock_mc_drop(sk, ifindex,
+						   &ip->sin6.sin6_addr);
+		release_sock(sk);
+#endif
+	}
+
+	return ret;
+}
+
+static bool vxlan_remcsum(struct vxlanhdr *unparsed,
+			  struct sk_buff *skb, u32 vxflags)
+{
+	size_t start, offset;
+
+	if (!(unparsed->vx_flags & VXLAN_HF_RCO) || skb->remcsum_offload)
+		goto out;
+
+	start = vxlan_rco_start(unparsed->vx_vni);
+	offset = start + vxlan_rco_offset(unparsed->vx_vni);
+
+	if (!pskb_may_pull(skb, offset + sizeof(u16)))
+		return false;
+
+	skb_remcsum_process(skb, (void *)(vxlan_hdr(skb) + 1), start, offset,
+			    !!(vxflags & VXLAN_F_REMCSUM_NOPARTIAL));
+out:
+	unparsed->vx_flags &= ~VXLAN_HF_RCO;
+	unparsed->vx_vni &= VXLAN_VNI_MASK;
+	return true;
+}
+
+static void vxlan_parse_gbp_hdr(struct vxlanhdr *unparsed,
+				struct sk_buff *skb, u32 vxflags,
+				struct vxlan_metadata *md)
+{
+	struct vxlanhdr_gbp *gbp = (struct vxlanhdr_gbp *)unparsed;
+	struct metadata_dst *tun_dst;
+
+	if (!(unparsed->vx_flags & VXLAN_HF_GBP))
+		goto out;
+
+	md->gbp = ntohs(gbp->policy_id);
+
+	tun_dst = (struct metadata_dst *)skb_dst(skb);
+	if (tun_dst) {
+		tun_dst->u.tun_info.key.tun_flags |= TUNNEL_VXLAN_OPT;
+		tun_dst->u.tun_info.options_len = sizeof(*md);
+	}
+	if (gbp->dont_learn)
+		md->gbp |= VXLAN_GBP_DONT_LEARN;
+
+	if (gbp->policy_applied)
+		md->gbp |= VXLAN_GBP_POLICY_APPLIED;
+
+	/* In flow-based mode, GBP is carried in dst_metadata */
+	if (!(vxflags & VXLAN_F_COLLECT_METADATA))
+		skb->mark = md->gbp;
+out:
+	unparsed->vx_flags &= ~VXLAN_GBP_USED_BITS;
+}
+
+static bool vxlan_set_mac(struct vxlan_dev *vxlan,
+			  struct vxlan_sock *vs,
+			  struct sk_buff *skb, __be32 vni)
+{
+	union vxlan_addr saddr;
+	u32 ifindex = skb->dev->ifindex;
+
+	skb_reset_mac_header(skb);
+	skb->protocol = eth_type_trans(skb, vxlan->dev);
+	skb_postpull_rcsum(skb, eth_hdr(skb), ETH_HLEN);
+
+	/* Ignore packet loops (and multicast echo) */
+	if (ether_addr_equal(eth_hdr(skb)->h_source, vxlan->dev->dev_addr))
+		return false;
+
+	/* Get address from the outer IP header */
+	if (vxlan_get_sk_family(vs) == AF_INET) {
+		saddr.sin.sin_addr.s_addr = ip_hdr(skb)->saddr;
+		saddr.sa.sa_family = AF_INET;
+#if IS_ENABLED(CONFIG_IPV6)
+	} else {
+		saddr.sin6.sin6_addr = ipv6_hdr(skb)->saddr;
+		saddr.sa.sa_family = AF_INET6;
+#endif
+	}
+
+	if ((vxlan->cfg.flags & VXLAN_F_LEARN) &&
+	    vxlan_snoop(skb->dev, &saddr, eth_hdr(skb)->h_source, ifindex, vni))
+		return false;
+
+	return true;
+}
+
+static bool vxlan_ecn_decapsulate(struct vxlan_sock *vs, void *oiph,
+				  struct sk_buff *skb)
+{
+	int err = 0;
+
+	if (vxlan_get_sk_family(vs) == AF_INET)
+		err = IP_ECN_decapsulate(oiph, skb);
+#if IS_ENABLED(CONFIG_IPV6)
+	else
+		err = IP6_ECN_decapsulate(oiph, skb);
+#endif
+
+	if (unlikely(err) && log_ecn_error) {
+		if (vxlan_get_sk_family(vs) == AF_INET)
+			net_info_ratelimited("non-ECT from %pI4 with TOS=%#x\n",
+					     &((struct iphdr *)oiph)->saddr,
+					     ((struct iphdr *)oiph)->tos);
+		else
+			net_info_ratelimited("non-ECT from %pI6\n",
+					     &((struct ipv6hdr *)oiph)->saddr);
+	}
+	return err <= 1;
+}
+
+/* Callback from net/ipv4/udp.c to receive packets */
+static int vxlan_rcv(struct sock *sk, struct sk_buff *skb)
+{
+	struct vxlan_dev *vxlan;
+	struct vxlan_sock *vs;
+	struct vxlanhdr unparsed;
+	struct vxlan_metadata _md;
+	struct vxlan_metadata *md = &_md;
+	__be16 protocol = htons(ETH_P_TEB);
+	bool raw_proto = false;
+	void *oiph;
+	__be32 vni = 0;
+
+	/* Need UDP and VXLAN header to be present */
+	if (!pskb_may_pull(skb, VXLAN_HLEN))
+		goto drop;
+
+	unparsed = *vxlan_hdr(skb);
+	/* VNI flag always required to be set */
+	if (!(unparsed.vx_flags & VXLAN_HF_VNI)) {
+		netdev_dbg(skb->dev, "invalid vxlan flags=%#x vni=%#x\n",
+			   ntohl(vxlan_hdr(skb)->vx_flags),
+			   ntohl(vxlan_hdr(skb)->vx_vni));
+		/* Return non vxlan pkt */
+		goto drop;
+	}
+	unparsed.vx_flags &= ~VXLAN_HF_VNI;
+	unparsed.vx_vni &= ~VXLAN_VNI_MASK;
+
+	vs = rcu_dereference_sk_user_data(sk);
+	if (!vs)
+		goto drop;
+
+	vni = vxlan_vni(vxlan_hdr(skb)->vx_vni);
+
+	vxlan = vxlan_vs_find_vni(vs, skb->dev->ifindex, vni);
+	if (!vxlan)
+		goto drop;
+
+	/* For backwards compatibility, only allow reserved fields to be
+	 * used by VXLAN extensions if explicitly requested.
+	 */
+	if (vs->flags & VXLAN_F_GPE) {
+		if (!vxlan_parse_gpe_proto(&unparsed, &protocol))
+			goto drop;
+		unparsed.vx_flags &= ~VXLAN_GPE_USED_BITS;
+		raw_proto = true;
+	}
+
+	if (__iptunnel_pull_header(skb, VXLAN_HLEN, protocol, raw_proto,
+				   !net_eq(vxlan->net, dev_net(vxlan->dev))))
+		goto drop;
+
+	if (vs->flags & VXLAN_F_REMCSUM_RX)
+		if (unlikely(!vxlan_remcsum(&unparsed, skb, vs->flags)))
+			goto drop;
+
+	if (vxlan_collect_metadata(vs)) {
+		struct metadata_dst *tun_dst;
+
+		tun_dst = udp_tun_rx_dst(skb, vxlan_get_sk_family(vs), TUNNEL_KEY,
+					 key32_to_tunnel_id(vni), sizeof(*md));
+
+		if (!tun_dst)
+			goto drop;
+
+		md = ip_tunnel_info_opts(&tun_dst->u.tun_info);
+
+		skb_dst_set(skb, (struct dst_entry *)tun_dst);
+	} else {
+		memset(md, 0, sizeof(*md));
+	}
+
+	if (vs->flags & VXLAN_F_GBP)
+		vxlan_parse_gbp_hdr(&unparsed, skb, vs->flags, md);
+	/* Note that GBP and GPE can never be active together. This is
+	 * ensured in vxlan_dev_configure.
+	 */
+
+	if (unparsed.vx_flags || unparsed.vx_vni) {
+		/* If there are any unprocessed flags remaining treat
+		 * this as a malformed packet. This behavior diverges from
+		 * VXLAN RFC (RFC7348) which stipulates that bits in reserved
+		 * in reserved fields are to be ignored. The approach here
+		 * maintains compatibility with previous stack code, and also
+		 * is more robust and provides a little more security in
+		 * adding extensions to VXLAN.
+		 */
+		goto drop;
+	}
+
+	if (!raw_proto) {
+		if (!vxlan_set_mac(vxlan, vs, skb, vni))
+			goto drop;
+	} else {
+		skb_reset_mac_header(skb);
+		skb->dev = vxlan->dev;
+		skb->pkt_type = PACKET_HOST;
+	}
+
+	oiph = skb_network_header(skb);
+	skb_reset_network_header(skb);
+
+	if (!vxlan_ecn_decapsulate(vs, oiph, skb)) {
+		++vxlan->dev->stats.rx_frame_errors;
+		++vxlan->dev->stats.rx_errors;
+		goto drop;
+	}
+
+	rcu_read_lock();
+
+	if (unlikely(!(vxlan->dev->flags & IFF_UP))) {
+		rcu_read_unlock();
+		atomic_long_inc(&vxlan->dev->rx_dropped);
+		goto drop;
+	}
+
+	dev_sw_netstats_rx_add(vxlan->dev, skb->len);
+	gro_cells_receive(&vxlan->gro_cells, skb);
+
+	rcu_read_unlock();
+
+	return 0;
+
+drop:
+	/* Consume bad packet */
+	kfree_skb(skb);
+	return 0;
+}
+
+/* Callback from net/ipv{4,6}/udp.c to check that we have a VNI for errors */
+static int vxlan_err_lookup(struct sock *sk, struct sk_buff *skb)
+{
+	struct vxlan_dev *vxlan;
+	struct vxlan_sock *vs;
+	struct vxlanhdr *hdr;
+	__be32 vni;
+
+	if (!pskb_may_pull(skb, skb_transport_offset(skb) + VXLAN_HLEN))
+		return -EINVAL;
+
+	hdr = vxlan_hdr(skb);
+
+	if (!(hdr->vx_flags & VXLAN_HF_VNI))
+		return -EINVAL;
+
+	vs = rcu_dereference_sk_user_data(sk);
+	if (!vs)
+		return -ENOENT;
+
+	vni = vxlan_vni(hdr->vx_vni);
+	vxlan = vxlan_vs_find_vni(vs, skb->dev->ifindex, vni);
+	if (!vxlan)
+		return -ENOENT;
+
+	return 0;
+}
+
+static int arp_reduce(struct net_device *dev, struct sk_buff *skb, __be32 vni)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct arphdr *parp;
+	u8 *arpptr, *sha;
+	__be32 sip, tip;
+	struct neighbour *n;
+
+	if (dev->flags & IFF_NOARP)
+		goto out;
+
+	if (!pskb_may_pull(skb, arp_hdr_len(dev))) {
+		dev->stats.tx_dropped++;
+		goto out;
+	}
+	parp = arp_hdr(skb);
+
+	if ((parp->ar_hrd != htons(ARPHRD_ETHER) &&
+	     parp->ar_hrd != htons(ARPHRD_IEEE802)) ||
+	    parp->ar_pro != htons(ETH_P_IP) ||
+	    parp->ar_op != htons(ARPOP_REQUEST) ||
+	    parp->ar_hln != dev->addr_len ||
+	    parp->ar_pln != 4)
+		goto out;
+	arpptr = (u8 *)parp + sizeof(struct arphdr);
+	sha = arpptr;
+	arpptr += dev->addr_len;	/* sha */
+	memcpy(&sip, arpptr, sizeof(sip));
+	arpptr += sizeof(sip);
+	arpptr += dev->addr_len;	/* tha */
+	memcpy(&tip, arpptr, sizeof(tip));
+
+	if (ipv4_is_loopback(tip) ||
+	    ipv4_is_multicast(tip))
+		goto out;
+
+	n = neigh_lookup(&arp_tbl, &tip, dev);
+
+	if (n) {
+		struct vxlan_fdb *f;
+		struct sk_buff	*reply;
+
+		if (!(n->nud_state & NUD_CONNECTED)) {
+			neigh_release(n);
+			goto out;
+		}
+
+		f = vxlan_find_mac(vxlan, n->ha, vni);
+		if (f && vxlan_addr_any(&(first_remote_rcu(f)->remote_ip))) {
+			/* bridge-local neighbor */
+			neigh_release(n);
+			goto out;
+		}
+
+		reply = arp_create(ARPOP_REPLY, ETH_P_ARP, sip, dev, tip, sha,
+				n->ha, sha);
+
+		neigh_release(n);
+
+		if (reply == NULL)
+			goto out;
+
+		skb_reset_mac_header(reply);
+		__skb_pull(reply, skb_network_offset(reply));
+		reply->ip_summed = CHECKSUM_UNNECESSARY;
+		reply->pkt_type = PACKET_HOST;
+
+		if (netif_rx_ni(reply) == NET_RX_DROP)
+			dev->stats.rx_dropped++;
+	} else if (vxlan->cfg.flags & VXLAN_F_L3MISS) {
+		union vxlan_addr ipa = {
+			.sin.sin_addr.s_addr = tip,
+			.sin.sin_family = AF_INET,
+		};
+
+		vxlan_ip_miss(dev, &ipa);
+	}
+out:
+	consume_skb(skb);
+	return NETDEV_TX_OK;
+}
+
+#if IS_ENABLED(CONFIG_IPV6)
+static struct sk_buff *vxlan_na_create(struct sk_buff *request,
+	struct neighbour *n, bool isrouter)
+{
+	struct net_device *dev = request->dev;
+	struct sk_buff *reply;
+	struct nd_msg *ns, *na;
+	struct ipv6hdr *pip6;
+	u8 *daddr;
+	int na_olen = 8; /* opt hdr + ETH_ALEN for target */
+	int ns_olen;
+	int i, len;
+
+	if (dev == NULL || !pskb_may_pull(request, request->len))
+		return NULL;
+
+	len = LL_RESERVED_SPACE(dev) + sizeof(struct ipv6hdr) +
+		sizeof(*na) + na_olen + dev->needed_tailroom;
+	reply = alloc_skb(len, GFP_ATOMIC);
+	if (reply == NULL)
+		return NULL;
+
+	reply->protocol = htons(ETH_P_IPV6);
+	reply->dev = dev;
+	skb_reserve(reply, LL_RESERVED_SPACE(request->dev));
+	skb_push(reply, sizeof(struct ethhdr));
+	skb_reset_mac_header(reply);
+
+	ns = (struct nd_msg *)(ipv6_hdr(request) + 1);
+
+	daddr = eth_hdr(request)->h_source;
+	ns_olen = request->len - skb_network_offset(request) -
+		sizeof(struct ipv6hdr) - sizeof(*ns);
+	for (i = 0; i < ns_olen-1; i += (ns->opt[i+1]<<3)) {
+		if (!ns->opt[i + 1]) {
+			kfree_skb(reply);
+			return NULL;
+		}
+		if (ns->opt[i] == ND_OPT_SOURCE_LL_ADDR) {
+			daddr = ns->opt + i + sizeof(struct nd_opt_hdr);
+			break;
+		}
+	}
+
+	/* Ethernet header */
+	ether_addr_copy(eth_hdr(reply)->h_dest, daddr);
+	ether_addr_copy(eth_hdr(reply)->h_source, n->ha);
+	eth_hdr(reply)->h_proto = htons(ETH_P_IPV6);
+	reply->protocol = htons(ETH_P_IPV6);
+
+	skb_pull(reply, sizeof(struct ethhdr));
+	skb_reset_network_header(reply);
+	skb_put(reply, sizeof(struct ipv6hdr));
+
+	/* IPv6 header */
+
+	pip6 = ipv6_hdr(reply);
+	memset(pip6, 0, sizeof(struct ipv6hdr));
+	pip6->version = 6;
+	pip6->priority = ipv6_hdr(request)->priority;
+	pip6->nexthdr = IPPROTO_ICMPV6;
+	pip6->hop_limit = 255;
+	pip6->daddr = ipv6_hdr(request)->saddr;
+	pip6->saddr = *(struct in6_addr *)n->primary_key;
+
+	skb_pull(reply, sizeof(struct ipv6hdr));
+	skb_reset_transport_header(reply);
+
+	/* Neighbor Advertisement */
+	na = skb_put_zero(reply, sizeof(*na) + na_olen);
+	na->icmph.icmp6_type = NDISC_NEIGHBOUR_ADVERTISEMENT;
+	na->icmph.icmp6_router = isrouter;
+	na->icmph.icmp6_override = 1;
+	na->icmph.icmp6_solicited = 1;
+	na->target = ns->target;
+	ether_addr_copy(&na->opt[2], n->ha);
+	na->opt[0] = ND_OPT_TARGET_LL_ADDR;
+	na->opt[1] = na_olen >> 3;
+
+	na->icmph.icmp6_cksum = csum_ipv6_magic(&pip6->saddr,
+		&pip6->daddr, sizeof(*na)+na_olen, IPPROTO_ICMPV6,
+		csum_partial(na, sizeof(*na)+na_olen, 0));
+
+	pip6->payload_len = htons(sizeof(*na)+na_olen);
+
+	skb_push(reply, sizeof(struct ipv6hdr));
+
+	reply->ip_summed = CHECKSUM_UNNECESSARY;
+
+	return reply;
+}
+
+static int neigh_reduce(struct net_device *dev, struct sk_buff *skb, __be32 vni)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	const struct in6_addr *daddr;
+	const struct ipv6hdr *iphdr;
+	struct inet6_dev *in6_dev;
+	struct neighbour *n;
+	struct nd_msg *msg;
+
+	rcu_read_lock();
+	in6_dev = __in6_dev_get(dev);
+	if (!in6_dev)
+		goto out;
+
+	iphdr = ipv6_hdr(skb);
+	daddr = &iphdr->daddr;
+	msg = (struct nd_msg *)(iphdr + 1);
+
+	if (ipv6_addr_loopback(daddr) ||
+	    ipv6_addr_is_multicast(&msg->target))
+		goto out;
+
+	n = neigh_lookup(ipv6_stub->nd_tbl, &msg->target, dev);
+
+	if (n) {
+		struct vxlan_fdb *f;
+		struct sk_buff *reply;
+
+		if (!(n->nud_state & NUD_CONNECTED)) {
+			neigh_release(n);
+			goto out;
+		}
+
+		f = vxlan_find_mac(vxlan, n->ha, vni);
+		if (f && vxlan_addr_any(&(first_remote_rcu(f)->remote_ip))) {
+			/* bridge-local neighbor */
+			neigh_release(n);
+			goto out;
+		}
+
+		reply = vxlan_na_create(skb, n,
+					!!(f ? f->flags & NTF_ROUTER : 0));
+
+		neigh_release(n);
+
+		if (reply == NULL)
+			goto out;
+
+		if (netif_rx_ni(reply) == NET_RX_DROP)
+			dev->stats.rx_dropped++;
+
+	} else if (vxlan->cfg.flags & VXLAN_F_L3MISS) {
+		union vxlan_addr ipa = {
+			.sin6.sin6_addr = msg->target,
+			.sin6.sin6_family = AF_INET6,
+		};
+
+		vxlan_ip_miss(dev, &ipa);
+	}
+
+out:
+	rcu_read_unlock();
+	consume_skb(skb);
+	return NETDEV_TX_OK;
+}
+#endif
+
+static bool route_shortcircuit(struct net_device *dev, struct sk_buff *skb)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct neighbour *n;
+
+	if (is_multicast_ether_addr(eth_hdr(skb)->h_dest))
+		return false;
+
+	n = NULL;
+	switch (ntohs(eth_hdr(skb)->h_proto)) {
+	case ETH_P_IP:
+	{
+		struct iphdr *pip;
+
+		if (!pskb_may_pull(skb, sizeof(struct iphdr)))
+			return false;
+		pip = ip_hdr(skb);
+		n = neigh_lookup(&arp_tbl, &pip->daddr, dev);
+		if (!n && (vxlan->cfg.flags & VXLAN_F_L3MISS)) {
+			union vxlan_addr ipa = {
+				.sin.sin_addr.s_addr = pip->daddr,
+				.sin.sin_family = AF_INET,
+			};
+
+			vxlan_ip_miss(dev, &ipa);
+			return false;
+		}
+
+		break;
+	}
+#if IS_ENABLED(CONFIG_IPV6)
+	case ETH_P_IPV6:
+	{
+		struct ipv6hdr *pip6;
+
+		if (!pskb_may_pull(skb, sizeof(struct ipv6hdr)))
+			return false;
+		pip6 = ipv6_hdr(skb);
+		n = neigh_lookup(ipv6_stub->nd_tbl, &pip6->daddr, dev);
+		if (!n && (vxlan->cfg.flags & VXLAN_F_L3MISS)) {
+			union vxlan_addr ipa = {
+				.sin6.sin6_addr = pip6->daddr,
+				.sin6.sin6_family = AF_INET6,
+			};
+
+			vxlan_ip_miss(dev, &ipa);
+			return false;
+		}
+
+		break;
+	}
+#endif
+	default:
+		return false;
+	}
+
+	if (n) {
+		bool diff;
+
+		diff = !ether_addr_equal(eth_hdr(skb)->h_dest, n->ha);
+		if (diff) {
+			memcpy(eth_hdr(skb)->h_source, eth_hdr(skb)->h_dest,
+				dev->addr_len);
+			memcpy(eth_hdr(skb)->h_dest, n->ha, dev->addr_len);
+		}
+		neigh_release(n);
+		return diff;
+	}
+
+	return false;
+}
+
+static void vxlan_build_gbp_hdr(struct vxlanhdr *vxh, u32 vxflags,
+				struct vxlan_metadata *md)
+{
+	struct vxlanhdr_gbp *gbp;
+
+	if (!md->gbp)
+		return;
+
+	gbp = (struct vxlanhdr_gbp *)vxh;
+	vxh->vx_flags |= VXLAN_HF_GBP;
+
+	if (md->gbp & VXLAN_GBP_DONT_LEARN)
+		gbp->dont_learn = 1;
+
+	if (md->gbp & VXLAN_GBP_POLICY_APPLIED)
+		gbp->policy_applied = 1;
+
+	gbp->policy_id = htons(md->gbp & VXLAN_GBP_ID_MASK);
+}
+
+static int vxlan_build_gpe_hdr(struct vxlanhdr *vxh, u32 vxflags,
+			       __be16 protocol)
+{
+	struct vxlanhdr_gpe *gpe = (struct vxlanhdr_gpe *)vxh;
+
+	gpe->np_applied = 1;
+	gpe->next_protocol = tun_p_from_eth_p(protocol);
+	if (!gpe->next_protocol)
+		return -EPFNOSUPPORT;
+	return 0;
+}
+
+static int vxlan_build_skb(struct sk_buff *skb, struct dst_entry *dst,
+			   int iphdr_len, __be32 vni,
+			   struct vxlan_metadata *md, u32 vxflags,
+			   bool udp_sum)
+{
+	struct vxlanhdr *vxh;
+	int min_headroom;
+	int err;
+	int type = udp_sum ? SKB_GSO_UDP_TUNNEL_CSUM : SKB_GSO_UDP_TUNNEL;
+	__be16 inner_protocol = htons(ETH_P_TEB);
+
+	if ((vxflags & VXLAN_F_REMCSUM_TX) &&
+	    skb->ip_summed == CHECKSUM_PARTIAL) {
+		int csum_start = skb_checksum_start_offset(skb);
+
+		if (csum_start <= VXLAN_MAX_REMCSUM_START &&
+		    !(csum_start & VXLAN_RCO_SHIFT_MASK) &&
+		    (skb->csum_offset == offsetof(struct udphdr, check) ||
+		     skb->csum_offset == offsetof(struct tcphdr, check)))
+			type |= SKB_GSO_TUNNEL_REMCSUM;
+	}
+
+	min_headroom = LL_RESERVED_SPACE(dst->dev) + dst->header_len
+			+ VXLAN_HLEN + iphdr_len;
+
+	/* Need space for new headers (invalidates iph ptr) */
+	err = skb_cow_head(skb, min_headroom);
+	if (unlikely(err))
+		return err;
+
+	err = iptunnel_handle_offloads(skb, type);
+	if (err)
+		return err;
+
+	vxh = __skb_push(skb, sizeof(*vxh));
+	vxh->vx_flags = VXLAN_HF_VNI;
+	vxh->vx_vni = vxlan_vni_field(vni);
+
+	if (type & SKB_GSO_TUNNEL_REMCSUM) {
+		unsigned int start;
+
+		start = skb_checksum_start_offset(skb) - sizeof(struct vxlanhdr);
+		vxh->vx_vni |= vxlan_compute_rco(start, skb->csum_offset);
+		vxh->vx_flags |= VXLAN_HF_RCO;
+
+		if (!skb_is_gso(skb)) {
+			skb->ip_summed = CHECKSUM_NONE;
+			skb->encapsulation = 0;
+		}
+	}
+
+	if (vxflags & VXLAN_F_GBP)
+		vxlan_build_gbp_hdr(vxh, vxflags, md);
+	if (vxflags & VXLAN_F_GPE) {
+		err = vxlan_build_gpe_hdr(vxh, vxflags, skb->protocol);
+		if (err < 0)
+			return err;
+		inner_protocol = skb->protocol;
+	}
+
+	skb_set_inner_protocol(skb, inner_protocol);
+	return 0;
+}
+
+static struct rtable *vxlan_get_route(struct vxlan_dev *vxlan, struct net_device *dev,
+				      struct vxlan_sock *sock4,
+				      struct sk_buff *skb, int oif, u8 tos,
+				      __be32 daddr, __be32 *saddr, __be16 dport, __be16 sport,
+				      struct dst_cache *dst_cache,
+				      const struct ip_tunnel_info *info)
+{
+	bool use_cache = ip_tunnel_dst_cache_usable(skb, info);
+	struct rtable *rt = NULL;
+	struct flowi4 fl4;
+
+	if (!sock4)
+		return ERR_PTR(-EIO);
+
+	if (tos && !info)
+		use_cache = false;
+	if (use_cache) {
+		rt = dst_cache_get_ip4(dst_cache, saddr);
+		if (rt)
+			return rt;
+	}
+
+	memset(&fl4, 0, sizeof(fl4));
+	fl4.flowi4_oif = oif;
+	fl4.flowi4_tos = RT_TOS(tos);
+	fl4.flowi4_mark = skb->mark;
+	fl4.flowi4_proto = IPPROTO_UDP;
+	fl4.daddr = daddr;
+	fl4.saddr = *saddr;
+	fl4.fl4_dport = dport;
+	fl4.fl4_sport = sport;
+
+	rt = ip_route_output_key(vxlan->net, &fl4);
+	if (!IS_ERR(rt)) {
+		if (rt->dst.dev == dev) {
+			netdev_dbg(dev, "circular route to %pI4\n", &daddr);
+			ip_rt_put(rt);
+			return ERR_PTR(-ELOOP);
+		}
+
+		*saddr = fl4.saddr;
+		if (use_cache)
+			dst_cache_set_ip4(dst_cache, &rt->dst, fl4.saddr);
+	} else {
+		netdev_dbg(dev, "no route to %pI4\n", &daddr);
+		return ERR_PTR(-ENETUNREACH);
+	}
+	return rt;
+}
+
+#if IS_ENABLED(CONFIG_IPV6)
+static struct dst_entry *vxlan6_get_route(struct vxlan_dev *vxlan,
+					  struct net_device *dev,
+					  struct vxlan_sock *sock6,
+					  struct sk_buff *skb, int oif, u8 tos,
+					  __be32 label,
+					  const struct in6_addr *daddr,
+					  struct in6_addr *saddr,
+					  __be16 dport, __be16 sport,
+					  struct dst_cache *dst_cache,
+					  const struct ip_tunnel_info *info)
+{
+	bool use_cache = ip_tunnel_dst_cache_usable(skb, info);
+	struct dst_entry *ndst;
+	struct flowi6 fl6;
+
+	if (!sock6)
+		return ERR_PTR(-EIO);
+
+	if (tos && !info)
+		use_cache = false;
+	if (use_cache) {
+		ndst = dst_cache_get_ip6(dst_cache, saddr);
+		if (ndst)
+			return ndst;
+	}
+
+	memset(&fl6, 0, sizeof(fl6));
+	fl6.flowi6_oif = oif;
+	fl6.daddr = *daddr;
+	fl6.saddr = *saddr;
+	fl6.flowlabel = ip6_make_flowinfo(RT_TOS(tos), label);
+	fl6.flowi6_mark = skb->mark;
+	fl6.flowi6_proto = IPPROTO_UDP;
+	fl6.fl6_dport = dport;
+	fl6.fl6_sport = sport;
+
+	ndst = ipv6_stub->ipv6_dst_lookup_flow(vxlan->net, sock6->sock->sk,
+					       &fl6, NULL);
+	if (IS_ERR(ndst)) {
+		netdev_dbg(dev, "no route to %pI6\n", daddr);
+		return ERR_PTR(-ENETUNREACH);
+	}
+
+	if (unlikely(ndst->dev == dev)) {
+		netdev_dbg(dev, "circular route to %pI6\n", daddr);
+		dst_release(ndst);
+		return ERR_PTR(-ELOOP);
+	}
+
+	*saddr = fl6.saddr;
+	if (use_cache)
+		dst_cache_set_ip6(dst_cache, ndst, saddr);
+	return ndst;
+}
+#endif
+
+/* Bypass encapsulation if the destination is local */
+static void vxlan_encap_bypass(struct sk_buff *skb, struct vxlan_dev *src_vxlan,
+			       struct vxlan_dev *dst_vxlan, __be32 vni,
+			       bool snoop)
+{
+	struct pcpu_sw_netstats *tx_stats, *rx_stats;
+	union vxlan_addr loopback;
+	union vxlan_addr *remote_ip = &dst_vxlan->default_dst.remote_ip;
+	struct net_device *dev;
+	int len = skb->len;
+
+	tx_stats = this_cpu_ptr(src_vxlan->dev->tstats);
+	rx_stats = this_cpu_ptr(dst_vxlan->dev->tstats);
+	skb->pkt_type = PACKET_HOST;
+	skb->encapsulation = 0;
+	skb->dev = dst_vxlan->dev;
+	__skb_pull(skb, skb_network_offset(skb));
+
+	if (remote_ip->sa.sa_family == AF_INET) {
+		loopback.sin.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
+		loopback.sa.sa_family =  AF_INET;
+#if IS_ENABLED(CONFIG_IPV6)
+	} else {
+		loopback.sin6.sin6_addr = in6addr_loopback;
+		loopback.sa.sa_family =  AF_INET6;
+#endif
+	}
+
+	rcu_read_lock();
+	dev = skb->dev;
+	if (unlikely(!(dev->flags & IFF_UP))) {
+		kfree_skb(skb);
+		goto drop;
+	}
+
+	if ((dst_vxlan->cfg.flags & VXLAN_F_LEARN) && snoop)
+		vxlan_snoop(dev, &loopback, eth_hdr(skb)->h_source, 0, vni);
+
+	u64_stats_update_begin(&tx_stats->syncp);
+	tx_stats->tx_packets++;
+	tx_stats->tx_bytes += len;
+	u64_stats_update_end(&tx_stats->syncp);
+
+	if (netif_rx(skb) == NET_RX_SUCCESS) {
+		u64_stats_update_begin(&rx_stats->syncp);
+		rx_stats->rx_packets++;
+		rx_stats->rx_bytes += len;
+		u64_stats_update_end(&rx_stats->syncp);
+	} else {
+drop:
+		dev->stats.rx_dropped++;
+	}
+	rcu_read_unlock();
+}
+
+static int encap_bypass_if_local(struct sk_buff *skb, struct net_device *dev,
+				 struct vxlan_dev *vxlan,
+				 union vxlan_addr *daddr,
+				 __be16 dst_port, int dst_ifindex, __be32 vni,
+				 struct dst_entry *dst,
+				 u32 rt_flags)
+{
+#if IS_ENABLED(CONFIG_IPV6)
+	/* IPv6 rt-flags are checked against RTF_LOCAL, but the value of
+	 * RTF_LOCAL is equal to RTCF_LOCAL. So to keep code simple
+	 * we can use RTCF_LOCAL which works for ipv4 and ipv6 route entry.
+	 */
+	BUILD_BUG_ON(RTCF_LOCAL != RTF_LOCAL);
+#endif
+	/* Bypass encapsulation if the destination is local */
+	if (rt_flags & RTCF_LOCAL &&
+	    !(rt_flags & (RTCF_BROADCAST | RTCF_MULTICAST))) {
+		struct vxlan_dev *dst_vxlan;
+
+		dst_release(dst);
+		dst_vxlan = vxlan_find_vni(vxlan->net, dst_ifindex, vni,
+					   daddr->sa.sa_family, dst_port,
+					   vxlan->cfg.flags);
+		if (!dst_vxlan) {
+			dev->stats.tx_errors++;
+			kfree_skb(skb);
+
+			return -ENOENT;
+		}
+		vxlan_encap_bypass(skb, vxlan, dst_vxlan, vni, true);
+		return 1;
+	}
+
+	return 0;
+}
+
+static void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,
+			   __be32 default_vni, struct vxlan_rdst *rdst,
+			   bool did_rsc)
+{
+	struct dst_cache *dst_cache;
+	struct ip_tunnel_info *info;
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	const struct iphdr *old_iph = ip_hdr(skb);
+	union vxlan_addr *dst;
+	union vxlan_addr remote_ip, local_ip;
+	struct vxlan_metadata _md;
+	struct vxlan_metadata *md = &_md;
+	__be16 src_port = 0, dst_port;
+	struct dst_entry *ndst = NULL;
+	__be32 vni, label;
+	__u8 tos, ttl;
+	int ifindex;
+	int err;
+	u32 flags = vxlan->cfg.flags;
+	bool udp_sum = false;
+	bool xnet = !net_eq(vxlan->net, dev_net(vxlan->dev));
+
+	info = skb_tunnel_info(skb);
+
+	if (rdst) {
+		dst = &rdst->remote_ip;
+		if (vxlan_addr_any(dst)) {
+			if (did_rsc) {
+				/* short-circuited back to local bridge */
+				vxlan_encap_bypass(skb, vxlan, vxlan,
+						   default_vni, true);
+				return;
+			}
+			goto drop;
+		}
+
+		dst_port = rdst->remote_port ? rdst->remote_port : vxlan->cfg.dst_port;
+		vni = (rdst->remote_vni) ? : default_vni;
+		ifindex = rdst->remote_ifindex;
+		local_ip = vxlan->cfg.saddr;
+		dst_cache = &rdst->dst_cache;
+		md->gbp = skb->mark;
+		if (flags & VXLAN_F_TTL_INHERIT) {
+			ttl = ip_tunnel_get_ttl(old_iph, skb);
+		} else {
+			ttl = vxlan->cfg.ttl;
+			if (!ttl && vxlan_addr_multicast(dst))
+				ttl = 1;
+		}
+
+		tos = vxlan->cfg.tos;
+		if (tos == 1)
+			tos = ip_tunnel_get_dsfield(old_iph, skb);
+
+		if (dst->sa.sa_family == AF_INET)
+			udp_sum = !(flags & VXLAN_F_UDP_ZERO_CSUM_TX);
+		else
+			udp_sum = !(flags & VXLAN_F_UDP_ZERO_CSUM6_TX);
+		label = vxlan->cfg.label;
+	} else {
+		if (!info) {
+			WARN_ONCE(1, "%s: Missing encapsulation instructions\n",
+				  dev->name);
+			goto drop;
+		}
+		remote_ip.sa.sa_family = ip_tunnel_info_af(info);
+		if (remote_ip.sa.sa_family == AF_INET) {
+			remote_ip.sin.sin_addr.s_addr = info->key.u.ipv4.dst;
+			local_ip.sin.sin_addr.s_addr = info->key.u.ipv4.src;
+		} else {
+			remote_ip.sin6.sin6_addr = info->key.u.ipv6.dst;
+			local_ip.sin6.sin6_addr = info->key.u.ipv6.src;
+		}
+		dst = &remote_ip;
+		dst_port = info->key.tp_dst ? : vxlan->cfg.dst_port;
+		vni = tunnel_id_to_key32(info->key.tun_id);
+		ifindex = 0;
+		dst_cache = &info->dst_cache;
+		if (info->key.tun_flags & TUNNEL_VXLAN_OPT) {
+			if (info->options_len < sizeof(*md))
+				goto drop;
+			md = ip_tunnel_info_opts(info);
+		}
+		ttl = info->key.ttl;
+		tos = info->key.tos;
+		label = info->key.label;
+		udp_sum = !!(info->key.tun_flags & TUNNEL_CSUM);
+	}
+	src_port = udp_flow_src_port(dev_net(dev), skb, vxlan->cfg.port_min,
+				     vxlan->cfg.port_max, true);
+
+	rcu_read_lock();
+	if (dst->sa.sa_family == AF_INET) {
+		struct vxlan_sock *sock4 = rcu_dereference(vxlan->vn4_sock);
+		struct rtable *rt;
+		__be16 df = 0;
+
+		if (!ifindex)
+			ifindex = sock4->sock->sk->sk_bound_dev_if;
+
+		rt = vxlan_get_route(vxlan, dev, sock4, skb, ifindex, tos,
+				     dst->sin.sin_addr.s_addr,
+				     &local_ip.sin.sin_addr.s_addr,
+				     dst_port, src_port,
+				     dst_cache, info);
+		if (IS_ERR(rt)) {
+			err = PTR_ERR(rt);
+			goto tx_error;
+		}
+
+		if (fan_has_map(&vxlan->fan) && rt->rt_flags & RTCF_LOCAL) {
+			netdev_dbg(dev, "discard fan to localhost %pI4\n",
+				   &dst->sin.sin_addr.s_addr);
+			rcu_read_unlock();
+			ip_rt_put(rt);
+			goto tx_free;
+		}
+
+		if (!info) {
+			/* Bypass encapsulation if the destination is local */
+			err = encap_bypass_if_local(skb, dev, vxlan, dst,
+						    dst_port, ifindex, vni,
+						    &rt->dst, rt->rt_flags);
+			if (err)
+				goto out_unlock;
+
+			if (vxlan->cfg.df == VXLAN_DF_SET) {
+				df = htons(IP_DF);
+			} else if (vxlan->cfg.df == VXLAN_DF_INHERIT) {
+				struct ethhdr *eth = eth_hdr(skb);
+
+				if (ntohs(eth->h_proto) == ETH_P_IPV6 ||
+				    (ntohs(eth->h_proto) == ETH_P_IP &&
+				     old_iph->frag_off & htons(IP_DF)))
+					df = htons(IP_DF);
+			}
+		} else if (info->key.tun_flags & TUNNEL_DONT_FRAGMENT) {
+			df = htons(IP_DF);
+		}
+
+		ndst = &rt->dst;
+		err = skb_tunnel_check_pmtu(skb, ndst, vxlan_headroom(flags & VXLAN_F_GPE),
+					    netif_is_any_bridge_port(dev));
+		if (err < 0) {
+			goto tx_error;
+		} else if (err) {
+			if (info) {
+				struct ip_tunnel_info *unclone;
+				struct in_addr src, dst;
+
+				unclone = skb_tunnel_info_unclone(skb);
+				if (unlikely(!unclone))
+					goto tx_error;
+
+				src = remote_ip.sin.sin_addr;
+				dst = local_ip.sin.sin_addr;
+				unclone->key.u.ipv4.src = src.s_addr;
+				unclone->key.u.ipv4.dst = dst.s_addr;
+			}
+			vxlan_encap_bypass(skb, vxlan, vxlan, vni, false);
+			dst_release(ndst);
+			goto out_unlock;
+		}
+
+		tos = ip_tunnel_ecn_encap(tos, old_iph, skb);
+		ttl = ttl ? : ip4_dst_hoplimit(&rt->dst);
+		err = vxlan_build_skb(skb, ndst, sizeof(struct iphdr),
+				      vni, md, flags, udp_sum);
+		if (err < 0)
+			goto tx_error;
+
+		udp_tunnel_xmit_skb(rt, sock4->sock->sk, skb, local_ip.sin.sin_addr.s_addr,
+				    dst->sin.sin_addr.s_addr, tos, ttl, df,
+				    src_port, dst_port, xnet, !udp_sum);
+#if IS_ENABLED(CONFIG_IPV6)
+	} else {
+		struct vxlan_sock *sock6 = rcu_dereference(vxlan->vn6_sock);
+
+		if (!ifindex)
+			ifindex = sock6->sock->sk->sk_bound_dev_if;
+
+		ndst = vxlan6_get_route(vxlan, dev, sock6, skb, ifindex, tos,
+					label, &dst->sin6.sin6_addr,
+					&local_ip.sin6.sin6_addr,
+					dst_port, src_port,
+					dst_cache, info);
+		if (IS_ERR(ndst)) {
+			err = PTR_ERR(ndst);
+			ndst = NULL;
+			goto tx_error;
+		}
+
+		if (!info) {
+			u32 rt6i_flags = ((struct rt6_info *)ndst)->rt6i_flags;
+
+			err = encap_bypass_if_local(skb, dev, vxlan, dst,
+						    dst_port, ifindex, vni,
+						    ndst, rt6i_flags);
+			if (err)
+				goto out_unlock;
+		}
+
+		err = skb_tunnel_check_pmtu(skb, ndst,
+					    vxlan_headroom((flags & VXLAN_F_GPE) | VXLAN_F_IPV6),
+					    netif_is_any_bridge_port(dev));
+		if (err < 0) {
+			goto tx_error;
+		} else if (err) {
+			if (info) {
+				struct ip_tunnel_info *unclone;
+				struct in6_addr src, dst;
+
+				unclone = skb_tunnel_info_unclone(skb);
+				if (unlikely(!unclone))
+					goto tx_error;
+
+				src = remote_ip.sin6.sin6_addr;
+				dst = local_ip.sin6.sin6_addr;
+				unclone->key.u.ipv6.src = src;
+				unclone->key.u.ipv6.dst = dst;
+			}
+
+			vxlan_encap_bypass(skb, vxlan, vxlan, vni, false);
+			dst_release(ndst);
+			goto out_unlock;
+		}
+
+		tos = ip_tunnel_ecn_encap(tos, old_iph, skb);
+		ttl = ttl ? : ip6_dst_hoplimit(ndst);
+		skb_scrub_packet(skb, xnet);
+		err = vxlan_build_skb(skb, ndst, sizeof(struct ipv6hdr),
+				      vni, md, flags, udp_sum);
+		if (err < 0)
+			goto tx_error;
+
+		udp_tunnel6_xmit_skb(ndst, sock6->sock->sk, skb, dev,
+				     &local_ip.sin6.sin6_addr,
+				     &dst->sin6.sin6_addr, tos, ttl,
+				     label, src_port, dst_port, !udp_sum);
+#endif
+	}
+out_unlock:
+	rcu_read_unlock();
+	return;
+
+drop:
+	dev->stats.tx_dropped++;
+	dev_kfree_skb(skb);
+	return;
+
+tx_error:
+	rcu_read_unlock();
+	if (err == -ELOOP)
+		dev->stats.collisions++;
+	else if (err == -ENETUNREACH)
+		dev->stats.tx_carrier_errors++;
+	dst_release(ndst);
+	dev->stats.tx_errors++;
+tx_free:
+	kfree_skb(skb);
+}
+
+static void vxlan_xmit_nh(struct sk_buff *skb, struct net_device *dev,
+			  struct vxlan_fdb *f, __be32 vni, bool did_rsc)
+{
+	struct vxlan_rdst nh_rdst;
+	struct nexthop *nh;
+	bool do_xmit;
+	u32 hash;
+
+	memset(&nh_rdst, 0, sizeof(struct vxlan_rdst));
+	hash = skb_get_hash(skb);
+
+	rcu_read_lock();
+	nh = rcu_dereference(f->nh);
+	if (!nh) {
+		rcu_read_unlock();
+		goto drop;
+	}
+	do_xmit = vxlan_fdb_nh_path_select(nh, hash, &nh_rdst);
+	rcu_read_unlock();
+
+	if (likely(do_xmit))
+		vxlan_xmit_one(skb, dev, vni, &nh_rdst, did_rsc);
+	else
+		goto drop;
+
+	return;
+
+drop:
+	dev->stats.tx_dropped++;
+	dev_kfree_skb(skb);
+}
+
+/* Transmit local packets over Vxlan
+ *
+ * Outer IP header inherits ECN and DF from inner header.
+ * Outer UDP destination is the VXLAN assigned port.
+ *           source port is based on hash of flow
+ */
+static netdev_tx_t vxlan_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_rdst *rdst, *fdst = NULL;
+	const struct ip_tunnel_info *info;
+	bool did_rsc = false;
+	struct vxlan_fdb *f;
+	struct ethhdr *eth;
+	__be32 vni = 0;
+
+	info = skb_tunnel_info(skb);
+
+	skb_reset_mac_header(skb);
+
+	if (vxlan->cfg.flags & VXLAN_F_COLLECT_METADATA) {
+		if (info && info->mode & IP_TUNNEL_INFO_BRIDGE &&
+		    info->mode & IP_TUNNEL_INFO_TX) {
+			vni = tunnel_id_to_key32(info->key.tun_id);
+		} else {
+			if (info && info->mode & IP_TUNNEL_INFO_TX)
+				vxlan_xmit_one(skb, dev, vni, NULL, false);
+			else
+				kfree_skb(skb);
+			return NETDEV_TX_OK;
+		}
+	}
+
+	if (vxlan->cfg.flags & VXLAN_F_PROXY) {
+		eth = eth_hdr(skb);
+		if (ntohs(eth->h_proto) == ETH_P_ARP)
+			return arp_reduce(dev, skb, vni);
+#if IS_ENABLED(CONFIG_IPV6)
+		else if (ntohs(eth->h_proto) == ETH_P_IPV6 &&
+			 pskb_may_pull(skb, sizeof(struct ipv6hdr) +
+					    sizeof(struct nd_msg)) &&
+			 ipv6_hdr(skb)->nexthdr == IPPROTO_ICMPV6) {
+			struct nd_msg *m = (struct nd_msg *)(ipv6_hdr(skb) + 1);
+
+			if (m->icmph.icmp6_code == 0 &&
+			    m->icmph.icmp6_type == NDISC_NEIGHBOUR_SOLICITATION)
+				return neigh_reduce(dev, skb, vni);
+		}
+#endif
+	}
+
+	if (fan_has_map(&vxlan->fan)) {
+		struct vxlan_rdst fan_rdst;
+
+		netdev_dbg(vxlan->dev, "vxlan_xmit p %x d %pM\n",
+			   eth->h_proto, eth->h_dest);
+		if (vxlan_fan_build_rdst(vxlan, skb, &fan_rdst)) {
+			dev->stats.tx_dropped++;
+			kfree_skb(skb);
+			return NETDEV_TX_OK;
+		}
+		vxlan_xmit_one(skb, dev, vni, &fan_rdst, 0);
+		return NETDEV_TX_OK;
+	}
+
+	eth = eth_hdr(skb);
+	f = vxlan_find_mac(vxlan, eth->h_dest, vni);
+	did_rsc = false;
+
+	if (f && (f->flags & NTF_ROUTER) && (vxlan->cfg.flags & VXLAN_F_RSC) &&
+	    (ntohs(eth->h_proto) == ETH_P_IP ||
+	     ntohs(eth->h_proto) == ETH_P_IPV6)) {
+		did_rsc = route_shortcircuit(dev, skb);
+		if (did_rsc)
+			f = vxlan_find_mac(vxlan, eth->h_dest, vni);
+	}
+
+	if (f == NULL) {
+		f = vxlan_find_mac(vxlan, all_zeros_mac, vni);
+		if (f == NULL) {
+			if ((vxlan->cfg.flags & VXLAN_F_L2MISS) &&
+			    !is_multicast_ether_addr(eth->h_dest))
+				vxlan_fdb_miss(vxlan, eth->h_dest);
+
+			dev->stats.tx_dropped++;
+			kfree_skb(skb);
+			return NETDEV_TX_OK;
+		}
+	}
+
+	if (rcu_access_pointer(f->nh)) {
+		vxlan_xmit_nh(skb, dev, f,
+			      (vni ? : vxlan->default_dst.remote_vni), did_rsc);
+	} else {
+		list_for_each_entry_rcu(rdst, &f->remotes, list) {
+			struct sk_buff *skb1;
+
+			if (!fdst) {
+				fdst = rdst;
+				continue;
+			}
+			skb1 = skb_clone(skb, GFP_ATOMIC);
+			if (skb1)
+				vxlan_xmit_one(skb1, dev, vni, rdst, did_rsc);
+		}
+		if (fdst)
+			vxlan_xmit_one(skb, dev, vni, fdst, did_rsc);
+		else
+			kfree_skb(skb);
+	}
+
+	return NETDEV_TX_OK;
+}
+
+/* Walk the forwarding table and purge stale entries */
+static void vxlan_cleanup(struct timer_list *t)
+{
+	struct vxlan_dev *vxlan = from_timer(vxlan, t, age_timer);
+	unsigned long next_timer = jiffies + FDB_AGE_INTERVAL;
+	unsigned int h;
+
+	if (!netif_running(vxlan->dev))
+		return;
+
+	for (h = 0; h < FDB_HASH_SIZE; ++h) {
+		struct hlist_node *p, *n;
+
+		spin_lock(&vxlan->hash_lock[h]);
+		hlist_for_each_safe(p, n, &vxlan->fdb_head[h]) {
+			struct vxlan_fdb *f
+				= container_of(p, struct vxlan_fdb, hlist);
+			unsigned long timeout;
+
+			if (f->state & (NUD_PERMANENT | NUD_NOARP))
+				continue;
+
+			if (f->flags & NTF_EXT_LEARNED)
+				continue;
+
+			timeout = f->used + vxlan->cfg.age_interval * HZ;
+			if (time_before_eq(timeout, jiffies)) {
+				netdev_dbg(vxlan->dev,
+					   "garbage collect %pM\n",
+					   f->eth_addr);
+				f->state = NUD_STALE;
+				vxlan_fdb_destroy(vxlan, f, true, true);
+			} else if (time_before(timeout, next_timer))
+				next_timer = timeout;
+		}
+		spin_unlock(&vxlan->hash_lock[h]);
+	}
+
+	mod_timer(&vxlan->age_timer, next_timer);
+}
+
+static void vxlan_vs_del_dev(struct vxlan_dev *vxlan)
+{
+	struct vxlan_net *vn = net_generic(vxlan->net, vxlan_net_id);
+
+	spin_lock(&vn->sock_lock);
+	hlist_del_init_rcu(&vxlan->hlist4.hlist);
+#if IS_ENABLED(CONFIG_IPV6)
+	hlist_del_init_rcu(&vxlan->hlist6.hlist);
+#endif
+	spin_unlock(&vn->sock_lock);
+}
+
+static void vxlan_vs_add_dev(struct vxlan_sock *vs, struct vxlan_dev *vxlan,
+			     struct vxlan_dev_node *node)
+{
+	struct vxlan_net *vn = net_generic(vxlan->net, vxlan_net_id);
+	__be32 vni = vxlan->default_dst.remote_vni;
+
+	node->vxlan = vxlan;
+	spin_lock(&vn->sock_lock);
+	hlist_add_head_rcu(&node->hlist, vni_head(vs, vni));
+	spin_unlock(&vn->sock_lock);
+}
+
+/* Setup stats when device is created */
+static int vxlan_init(struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	int err;
+
+	dev->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
+	if (!dev->tstats)
+		return -ENOMEM;
+
+	err = gro_cells_init(&vxlan->gro_cells, dev);
+	if (err) {
+		free_percpu(dev->tstats);
+		return err;
+	}
+
+	return 0;
+}
+
+static void vxlan_fdb_delete_default(struct vxlan_dev *vxlan, __be32 vni)
+{
+	struct vxlan_fdb *f;
+	u32 hash_index = fdb_head_index(vxlan, all_zeros_mac, vni);
+
+	spin_lock_bh(&vxlan->hash_lock[hash_index]);
+	f = __vxlan_find_mac(vxlan, all_zeros_mac, vni);
+	if (f)
+		vxlan_fdb_destroy(vxlan, f, true, true);
+	spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+}
+
+static void vxlan_uninit(struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+
+	gro_cells_destroy(&vxlan->gro_cells);
+
+	vxlan_fdb_delete_default(vxlan, vxlan->cfg.vni);
+
+	free_percpu(dev->tstats);
+}
+
+/* Start ageing timer and join group when device is brought up */
+static int vxlan_open(struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	int ret;
+
+	ret = vxlan_sock_add(vxlan);
+	if (ret < 0)
+		return ret;
+
+	if (vxlan_addr_multicast(&vxlan->default_dst.remote_ip)) {
+		ret = vxlan_igmp_join(vxlan);
+		if (ret == -EADDRINUSE)
+			ret = 0;
+		if (ret) {
+			vxlan_sock_release(vxlan);
+			return ret;
+		}
+	}
+
+	if (vxlan->cfg.age_interval)
+		mod_timer(&vxlan->age_timer, jiffies + FDB_AGE_INTERVAL);
+
+	return ret;
+}
+
+/* Purge the forwarding table */
+static void vxlan_flush(struct vxlan_dev *vxlan, bool do_all)
+{
+	unsigned int h;
+
+	for (h = 0; h < FDB_HASH_SIZE; ++h) {
+		struct hlist_node *p, *n;
+
+		spin_lock_bh(&vxlan->hash_lock[h]);
+		hlist_for_each_safe(p, n, &vxlan->fdb_head[h]) {
+			struct vxlan_fdb *f
+				= container_of(p, struct vxlan_fdb, hlist);
+			if (!do_all && (f->state & (NUD_PERMANENT | NUD_NOARP)))
+				continue;
+			/* the all_zeros_mac entry is deleted at vxlan_uninit */
+			if (is_zero_ether_addr(f->eth_addr) &&
+			    f->vni == vxlan->cfg.vni)
+				continue;
+			vxlan_fdb_destroy(vxlan, f, true, true);
+		}
+		spin_unlock_bh(&vxlan->hash_lock[h]);
+	}
+}
+
+/* Cleanup timer and forwarding table on shutdown */
+static int vxlan_stop(struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_net *vn = net_generic(vxlan->net, vxlan_net_id);
+	int ret = 0;
+
+	if (vxlan_addr_multicast(&vxlan->default_dst.remote_ip) &&
+	    !vxlan_group_used(vn, vxlan))
+		ret = vxlan_igmp_leave(vxlan);
+
+	del_timer_sync(&vxlan->age_timer);
+
+	vxlan_flush(vxlan, false);
+	vxlan_sock_release(vxlan);
+
+	return ret;
+}
+
+/* Stub, nothing needs to be done. */
+static void vxlan_set_multicast_list(struct net_device *dev)
+{
+}
+
+static int vxlan_change_mtu(struct net_device *dev, int new_mtu)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_rdst *dst = &vxlan->default_dst;
+	struct net_device *lowerdev = __dev_get_by_index(vxlan->net,
+							 dst->remote_ifindex);
+
+	/* This check is different than dev->max_mtu, because it looks at
+	 * the lowerdev->mtu, rather than the static dev->max_mtu
+	 */
+	if (lowerdev) {
+		int max_mtu = lowerdev->mtu - vxlan_headroom(vxlan->cfg.flags);
+		if (new_mtu > max_mtu)
+			return -EINVAL;
+	}
+
+	dev->mtu = new_mtu;
+	return 0;
+}
+
+static int vxlan_fill_metadata_dst(struct net_device *dev, struct sk_buff *skb)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct ip_tunnel_info *info = skb_tunnel_info(skb);
+	__be16 sport, dport;
+
+	sport = udp_flow_src_port(dev_net(dev), skb, vxlan->cfg.port_min,
+				  vxlan->cfg.port_max, true);
+	dport = info->key.tp_dst ? : vxlan->cfg.dst_port;
+
+	if (ip_tunnel_info_af(info) == AF_INET) {
+		struct vxlan_sock *sock4 = rcu_dereference(vxlan->vn4_sock);
+		struct rtable *rt;
+
+		rt = vxlan_get_route(vxlan, dev, sock4, skb, 0, info->key.tos,
+				     info->key.u.ipv4.dst,
+				     &info->key.u.ipv4.src, dport, sport,
+				     &info->dst_cache, info);
+		if (IS_ERR(rt))
+			return PTR_ERR(rt);
+		ip_rt_put(rt);
+	} else {
+#if IS_ENABLED(CONFIG_IPV6)
+		struct vxlan_sock *sock6 = rcu_dereference(vxlan->vn6_sock);
+		struct dst_entry *ndst;
+
+		ndst = vxlan6_get_route(vxlan, dev, sock6, skb, 0, info->key.tos,
+					info->key.label, &info->key.u.ipv6.dst,
+					&info->key.u.ipv6.src, dport, sport,
+					&info->dst_cache, info);
+		if (IS_ERR(ndst))
+			return PTR_ERR(ndst);
+		dst_release(ndst);
+#else /* !CONFIG_IPV6 */
+		return -EPFNOSUPPORT;
+#endif
+	}
+	info->key.tp_src = sport;
+	info->key.tp_dst = dport;
+	return 0;
+}
+
+static const struct net_device_ops vxlan_netdev_ether_ops = {
+	.ndo_init		= vxlan_init,
+	.ndo_uninit		= vxlan_uninit,
+	.ndo_open		= vxlan_open,
+	.ndo_stop		= vxlan_stop,
+	.ndo_start_xmit		= vxlan_xmit,
+	.ndo_get_stats64	= dev_get_tstats64,
+	.ndo_set_rx_mode	= vxlan_set_multicast_list,
+	.ndo_change_mtu		= vxlan_change_mtu,
+	.ndo_validate_addr	= eth_validate_addr,
+	.ndo_set_mac_address	= eth_mac_addr,
+	.ndo_fdb_add		= vxlan_fdb_add,
+	.ndo_fdb_del		= vxlan_fdb_delete,
+	.ndo_fdb_dump		= vxlan_fdb_dump,
+	.ndo_fdb_get		= vxlan_fdb_get,
+	.ndo_fill_metadata_dst	= vxlan_fill_metadata_dst,
+	.ndo_change_proto_down  = dev_change_proto_down_generic,
+};
+
+static const struct net_device_ops vxlan_netdev_raw_ops = {
+	.ndo_init		= vxlan_init,
+	.ndo_uninit		= vxlan_uninit,
+	.ndo_open		= vxlan_open,
+	.ndo_stop		= vxlan_stop,
+	.ndo_start_xmit		= vxlan_xmit,
+	.ndo_get_stats64	= dev_get_tstats64,
+	.ndo_change_mtu		= vxlan_change_mtu,
+	.ndo_fill_metadata_dst	= vxlan_fill_metadata_dst,
+};
+
+/* Info for udev, that this is a virtual tunnel endpoint */
+static struct device_type vxlan_type = {
+	.name = "vxlan",
+};
+
+/* Calls the ndo_udp_tunnel_add of the caller in order to
+ * supply the listening VXLAN udp ports. Callers are expected
+ * to implement the ndo_udp_tunnel_add.
+ */
+static void vxlan_offload_rx_ports(struct net_device *dev, bool push)
+{
+	struct vxlan_sock *vs;
+	struct net *net = dev_net(dev);
+	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+	unsigned int i;
+
+	spin_lock(&vn->sock_lock);
+	for (i = 0; i < PORT_HASH_SIZE; ++i) {
+		hlist_for_each_entry_rcu(vs, &vn->sock_list[i], hlist) {
+			unsigned short type;
+
+			if (vs->flags & VXLAN_F_GPE)
+				type = UDP_TUNNEL_TYPE_VXLAN_GPE;
+			else
+				type = UDP_TUNNEL_TYPE_VXLAN;
+
+			if (push)
+				udp_tunnel_push_rx_port(dev, vs->sock, type);
+			else
+				udp_tunnel_drop_rx_port(dev, vs->sock, type);
+		}
+	}
+	spin_unlock(&vn->sock_lock);
+}
+
+/* Initialize the device structure. */
+static void vxlan_setup(struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	unsigned int h;
+
+	eth_hw_addr_random(dev);
+	ether_setup(dev);
+
+	dev->needs_free_netdev = true;
+	SET_NETDEV_DEVTYPE(dev, &vxlan_type);
+
+	dev->features	|= NETIF_F_LLTX;
+	dev->features	|= NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_FRAGLIST;
+	dev->features   |= NETIF_F_RXCSUM;
+	dev->features   |= NETIF_F_GSO_SOFTWARE;
+
+	dev->vlan_features = dev->features;
+	dev->hw_features |= NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_FRAGLIST;
+	dev->hw_features |= NETIF_F_RXCSUM;
+	dev->hw_features |= NETIF_F_GSO_SOFTWARE;
+	netif_keep_dst(dev);
+	dev->priv_flags |= IFF_NO_QUEUE;
+
+	/* MTU range: 68 - 65535 */
+	dev->min_mtu = ETH_MIN_MTU;
+	dev->max_mtu = ETH_MAX_MTU;
+
+	INIT_LIST_HEAD(&vxlan->next);
+
+	timer_setup(&vxlan->age_timer, vxlan_cleanup, TIMER_DEFERRABLE);
+
+	vxlan->dev = dev;
+
+	for (h = 0; h < FDB_HASH_SIZE; ++h) {
+		spin_lock_init(&vxlan->hash_lock[h]);
+		INIT_HLIST_HEAD(&vxlan->fdb_head[h]);
+	}
+
+	INIT_LIST_HEAD(&vxlan->fan.fan_maps);
+}
+
+static void vxlan_ether_setup(struct net_device *dev)
+{
+	dev->priv_flags &= ~IFF_TX_SKB_SHARING;
+	dev->priv_flags |= IFF_LIVE_ADDR_CHANGE;
+	dev->netdev_ops = &vxlan_netdev_ether_ops;
+}
+
+static void vxlan_raw_setup(struct net_device *dev)
+{
+	dev->header_ops = NULL;
+	dev->type = ARPHRD_NONE;
+	dev->hard_header_len = 0;
+	dev->addr_len = 0;
+	dev->flags = IFF_POINTOPOINT | IFF_NOARP | IFF_MULTICAST;
+	dev->netdev_ops = &vxlan_netdev_raw_ops;
+}
+
+static const struct nla_policy vxlan_policy[IFLA_VXLAN_MAX + 1] = {
+	[IFLA_VXLAN_ID]		= { .type = NLA_U32 },
+	[IFLA_VXLAN_GROUP]	= { .len = sizeof_field(struct iphdr, daddr) },
+	[IFLA_VXLAN_GROUP6]	= { .len = sizeof(struct in6_addr) },
+	[IFLA_VXLAN_LINK]	= { .type = NLA_U32 },
+	[IFLA_VXLAN_LOCAL]	= { .len = sizeof_field(struct iphdr, saddr) },
+	[IFLA_VXLAN_LOCAL6]	= { .len = sizeof(struct in6_addr) },
+	[IFLA_VXLAN_TOS]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_TTL]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_LABEL]	= { .type = NLA_U32 },
+	[IFLA_VXLAN_LEARNING]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_AGEING]	= { .type = NLA_U32 },
+	[IFLA_VXLAN_LIMIT]	= { .type = NLA_U32 },
+	[IFLA_VXLAN_PORT_RANGE] = { .len  = sizeof(struct ifla_vxlan_port_range) },
+	[IFLA_VXLAN_PROXY]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_RSC]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_L2MISS]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_L3MISS]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_COLLECT_METADATA]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_PORT]	= { .type = NLA_U16 },
+	[IFLA_VXLAN_UDP_CSUM]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_UDP_ZERO_CSUM6_TX]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_UDP_ZERO_CSUM6_RX]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_REMCSUM_TX]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_REMCSUM_RX]	= { .type = NLA_U8 },
+	[IFLA_VXLAN_GBP]	= { .type = NLA_FLAG, },
+	[IFLA_VXLAN_GPE]	= { .type = NLA_FLAG, },
+	[IFLA_VXLAN_REMCSUM_NOPARTIAL]	= { .type = NLA_FLAG },
+	[IFLA_VXLAN_TTL_INHERIT]	= { .type = NLA_FLAG },
+	[IFLA_VXLAN_DF]		= { .type = NLA_U8 },
+};
+
+static int vxlan_validate(struct nlattr *tb[], struct nlattr *data[],
+			  struct netlink_ext_ack *extack)
+{
+	if (tb[IFLA_ADDRESS]) {
+		if (nla_len(tb[IFLA_ADDRESS]) != ETH_ALEN) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_ADDRESS],
+					    "Provided link layer address is not Ethernet");
+			return -EINVAL;
+		}
+
+		if (!is_valid_ether_addr(nla_data(tb[IFLA_ADDRESS]))) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_ADDRESS],
+					    "Provided Ethernet address is not unicast");
+			return -EADDRNOTAVAIL;
+		}
+	}
+
+	if (tb[IFLA_MTU]) {
+		u32 mtu = nla_get_u32(tb[IFLA_MTU]);
+
+		if (mtu < ETH_MIN_MTU || mtu > ETH_MAX_MTU) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_MTU],
+					    "MTU must be between 68 and 65535");
+			return -EINVAL;
+		}
+	}
+
+	if (!data) {
+		NL_SET_ERR_MSG(extack,
+			       "Required attributes not provided to perform the operation");
+		return -EINVAL;
+	}
+
+	if (data[IFLA_VXLAN_ID]) {
+		u32 id = nla_get_u32(data[IFLA_VXLAN_ID]);
+
+		if (id >= VXLAN_N_VID) {
+			NL_SET_ERR_MSG_ATTR(extack, data[IFLA_VXLAN_ID],
+					    "VXLAN ID must be lower than 16777216");
+			return -ERANGE;
+		}
+	}
+
+	if (data[IFLA_VXLAN_PORT_RANGE]) {
+		const struct ifla_vxlan_port_range *p
+			= nla_data(data[IFLA_VXLAN_PORT_RANGE]);
+
+		if (ntohs(p->high) < ntohs(p->low)) {
+			NL_SET_ERR_MSG_ATTR(extack, data[IFLA_VXLAN_PORT_RANGE],
+					    "Invalid source port range");
+			return -EINVAL;
+		}
+	}
+
+	if (data[IFLA_VXLAN_DF]) {
+		enum ifla_vxlan_df df = nla_get_u8(data[IFLA_VXLAN_DF]);
+
+		if (df < 0 || df > VXLAN_DF_MAX) {
+			NL_SET_ERR_MSG_ATTR(extack, data[IFLA_VXLAN_DF],
+					    "Invalid DF attribute");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static void vxlan_get_drvinfo(struct net_device *netdev,
+			      struct ethtool_drvinfo *drvinfo)
+{
+	strlcpy(drvinfo->version, VXLAN_VERSION, sizeof(drvinfo->version));
+	strlcpy(drvinfo->driver, "vxlan", sizeof(drvinfo->driver));
+}
+
+static int vxlan_get_link_ksettings(struct net_device *dev,
+				    struct ethtool_link_ksettings *cmd)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_rdst *dst = &vxlan->default_dst;
+	struct net_device *lowerdev = __dev_get_by_index(vxlan->net,
+							 dst->remote_ifindex);
+
+	if (!lowerdev) {
+		cmd->base.duplex = DUPLEX_UNKNOWN;
+		cmd->base.port = PORT_OTHER;
+		cmd->base.speed = SPEED_UNKNOWN;
+
+		return 0;
+	}
+
+	return __ethtool_get_link_ksettings(lowerdev, cmd);
+}
+
+static const struct ethtool_ops vxlan_ethtool_ops = {
+	.get_drvinfo		= vxlan_get_drvinfo,
+	.get_link		= ethtool_op_get_link,
+	.get_link_ksettings	= vxlan_get_link_ksettings,
+};
+
+static struct socket *vxlan_create_sock(struct net *net, bool ipv6,
+					__be16 port, u32 flags, int ifindex)
+{
+	struct socket *sock;
+	struct udp_port_cfg udp_conf;
+	int err;
+
+	memset(&udp_conf, 0, sizeof(udp_conf));
+
+	if (ipv6) {
+		udp_conf.family = AF_INET6;
+		udp_conf.use_udp6_rx_checksums =
+		    !(flags & VXLAN_F_UDP_ZERO_CSUM6_RX);
+		udp_conf.ipv6_v6only = 1;
+	} else {
+		udp_conf.family = AF_INET;
+	}
+
+	udp_conf.local_udp_port = port;
+	udp_conf.bind_ifindex = ifindex;
+
+	/* Open UDP socket */
+	err = udp_sock_create(net, &udp_conf, &sock);
+	if (err < 0)
+		return ERR_PTR(err);
+
+	udp_allow_gso(sock->sk);
+	return sock;
+}
+
+/* Create new listen socket if needed */
+static struct vxlan_sock *vxlan_socket_create(struct net *net, bool ipv6,
+					      __be16 port, u32 flags,
+					      int ifindex)
+{
+	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+	struct vxlan_sock *vs;
+	struct socket *sock;
+	unsigned int h;
+	struct udp_tunnel_sock_cfg tunnel_cfg;
+
+	vs = kzalloc(sizeof(*vs), GFP_KERNEL);
+	if (!vs)
+		return ERR_PTR(-ENOMEM);
+
+	for (h = 0; h < VNI_HASH_SIZE; ++h)
+		INIT_HLIST_HEAD(&vs->vni_list[h]);
+
+	sock = vxlan_create_sock(net, ipv6, port, flags, ifindex);
+	if (IS_ERR(sock)) {
+		kfree(vs);
+		return ERR_CAST(sock);
+	}
+
+	vs->sock = sock;
+	refcount_set(&vs->refcnt, 1);
+	vs->flags = (flags & VXLAN_F_RCV_FLAGS);
+
+	spin_lock(&vn->sock_lock);
+	hlist_add_head_rcu(&vs->hlist, vs_head(net, port));
+	udp_tunnel_notify_add_rx_port(sock,
+				      (vs->flags & VXLAN_F_GPE) ?
+				      UDP_TUNNEL_TYPE_VXLAN_GPE :
+				      UDP_TUNNEL_TYPE_VXLAN);
+	spin_unlock(&vn->sock_lock);
+
+	/* Mark socket as an encapsulation socket. */
+	memset(&tunnel_cfg, 0, sizeof(tunnel_cfg));
+	tunnel_cfg.sk_user_data = vs;
+	tunnel_cfg.encap_type = 1;
+	tunnel_cfg.encap_rcv = vxlan_rcv;
+	tunnel_cfg.encap_err_lookup = vxlan_err_lookup;
+	tunnel_cfg.encap_destroy = NULL;
+	tunnel_cfg.gro_receive = vxlan_gro_receive;
+	tunnel_cfg.gro_complete = vxlan_gro_complete;
+
+	setup_udp_tunnel_sock(net, sock, &tunnel_cfg);
+
+	return vs;
+}
+
+static int __vxlan_sock_add(struct vxlan_dev *vxlan, bool ipv6)
+{
+	struct vxlan_net *vn = net_generic(vxlan->net, vxlan_net_id);
+	struct vxlan_sock *vs = NULL;
+	struct vxlan_dev_node *node;
+	int l3mdev_index = 0;
+
+	if (vxlan->cfg.remote_ifindex)
+		l3mdev_index = l3mdev_master_upper_ifindex_by_index(
+			vxlan->net, vxlan->cfg.remote_ifindex);
+
+	if (!vxlan->cfg.no_share) {
+		spin_lock(&vn->sock_lock);
+		vs = vxlan_find_sock(vxlan->net, ipv6 ? AF_INET6 : AF_INET,
+				     vxlan->cfg.dst_port, vxlan->cfg.flags,
+				     l3mdev_index);
+		if (vs && !refcount_inc_not_zero(&vs->refcnt)) {
+			spin_unlock(&vn->sock_lock);
+			return -EBUSY;
+		}
+		spin_unlock(&vn->sock_lock);
+	}
+	if (!vs)
+		vs = vxlan_socket_create(vxlan->net, ipv6,
+					 vxlan->cfg.dst_port, vxlan->cfg.flags,
+					 l3mdev_index);
+	if (IS_ERR(vs))
+		return PTR_ERR(vs);
+#if IS_ENABLED(CONFIG_IPV6)
+	if (ipv6) {
+		rcu_assign_pointer(vxlan->vn6_sock, vs);
+		node = &vxlan->hlist6;
+	} else
+#endif
+	{
+		rcu_assign_pointer(vxlan->vn4_sock, vs);
+		node = &vxlan->hlist4;
+	}
+	vxlan_vs_add_dev(vs, vxlan, node);
+	return 0;
+}
+
+static int vxlan_sock_add(struct vxlan_dev *vxlan)
+{
+	bool metadata = vxlan->cfg.flags & VXLAN_F_COLLECT_METADATA;
+	bool ipv6 = vxlan->cfg.flags & VXLAN_F_IPV6 || metadata;
+	bool ipv4 = !ipv6 || metadata;
+	int ret = 0;
+
+	RCU_INIT_POINTER(vxlan->vn4_sock, NULL);
+#if IS_ENABLED(CONFIG_IPV6)
+	RCU_INIT_POINTER(vxlan->vn6_sock, NULL);
+	if (ipv6) {
+		ret = __vxlan_sock_add(vxlan, true);
+		if (ret < 0 && ret != -EAFNOSUPPORT)
+			ipv4 = false;
+	}
+#endif
+	if (ipv4)
+		ret = __vxlan_sock_add(vxlan, false);
+	if (ret < 0)
+		vxlan_sock_release(vxlan);
+	return ret;
+}
+
+static int vxlan_config_validate(struct net *src_net, struct vxlan_config *conf,
+				 struct net_device **lower,
+				 struct vxlan_dev *old,
+				 struct netlink_ext_ack *extack)
+{
+	struct vxlan_net *vn = net_generic(src_net, vxlan_net_id);
+	struct vxlan_dev *tmp;
+	bool use_ipv6 = false;
+
+	if (conf->flags & VXLAN_F_GPE) {
+		/* For now, allow GPE only together with
+		 * COLLECT_METADATA. This can be relaxed later; in such
+		 * case, the other side of the PtP link will have to be
+		 * provided.
+		 */
+		if ((conf->flags & ~VXLAN_F_ALLOWED_GPE) ||
+		    !(conf->flags & VXLAN_F_COLLECT_METADATA)) {
+			NL_SET_ERR_MSG(extack,
+				       "VXLAN GPE does not support this combination of attributes");
+			return -EINVAL;
+		}
+	}
+
+	if (!conf->remote_ip.sa.sa_family && !conf->saddr.sa.sa_family) {
+		/* Unless IPv6 is explicitly requested, assume IPv4 */
+		conf->remote_ip.sa.sa_family = AF_INET;
+		conf->saddr.sa.sa_family = AF_INET;
+	} else if (!conf->remote_ip.sa.sa_family) {
+		conf->remote_ip.sa.sa_family = conf->saddr.sa.sa_family;
+	} else if (!conf->saddr.sa.sa_family) {
+		conf->saddr.sa.sa_family = conf->remote_ip.sa.sa_family;
+	}
+
+	if (conf->saddr.sa.sa_family != conf->remote_ip.sa.sa_family) {
+		NL_SET_ERR_MSG(extack,
+			       "Local and remote address must be from the same family");
+		return -EINVAL;
+	}
+
+	if (vxlan_addr_multicast(&conf->saddr)) {
+		NL_SET_ERR_MSG(extack, "Local address cannot be multicast");
+		return -EINVAL;
+	}
+
+	if (conf->saddr.sa.sa_family == AF_INET6) {
+		if (!IS_ENABLED(CONFIG_IPV6)) {
+			NL_SET_ERR_MSG(extack,
+				       "IPv6 support not enabled in the kernel");
+			return -EPFNOSUPPORT;
+		}
+		use_ipv6 = true;
+		conf->flags |= VXLAN_F_IPV6;
+
+		if (!(conf->flags & VXLAN_F_COLLECT_METADATA)) {
+			int local_type =
+				ipv6_addr_type(&conf->saddr.sin6.sin6_addr);
+			int remote_type =
+				ipv6_addr_type(&conf->remote_ip.sin6.sin6_addr);
+
+			if (local_type & IPV6_ADDR_LINKLOCAL) {
+				if (!(remote_type & IPV6_ADDR_LINKLOCAL) &&
+				    (remote_type != IPV6_ADDR_ANY)) {
+					NL_SET_ERR_MSG(extack,
+						       "Invalid combination of local and remote address scopes");
+					return -EINVAL;
+				}
+
+				conf->flags |= VXLAN_F_IPV6_LINKLOCAL;
+			} else {
+				if (remote_type ==
+				    (IPV6_ADDR_UNICAST | IPV6_ADDR_LINKLOCAL)) {
+					NL_SET_ERR_MSG(extack,
+						       "Invalid combination of local and remote address scopes");
+					return -EINVAL;
+				}
+
+				conf->flags &= ~VXLAN_F_IPV6_LINKLOCAL;
+			}
+		}
+	}
+
+	if (conf->label && !use_ipv6) {
+		NL_SET_ERR_MSG(extack,
+			       "Label attribute only applies to IPv6 VXLAN devices");
+		return -EINVAL;
+	}
+
+	if (conf->remote_ifindex) {
+		struct net_device *lowerdev;
+
+		lowerdev = __dev_get_by_index(src_net, conf->remote_ifindex);
+		if (!lowerdev) {
+			NL_SET_ERR_MSG(extack,
+				       "Invalid local interface, device not found");
+			return -ENODEV;
+		}
+
+#if IS_ENABLED(CONFIG_IPV6)
+		if (use_ipv6) {
+			struct inet6_dev *idev = __in6_dev_get(lowerdev);
+
+			if (idev && idev->cnf.disable_ipv6) {
+				NL_SET_ERR_MSG(extack,
+					       "IPv6 support disabled by administrator");
+				return -EPERM;
+			}
+		}
+#endif
+
+		*lower = lowerdev;
+	} else {
+		if (vxlan_addr_multicast(&conf->remote_ip)) {
+			NL_SET_ERR_MSG(extack,
+				       "Local interface required for multicast remote destination");
+
+			return -EINVAL;
+		}
+
+#if IS_ENABLED(CONFIG_IPV6)
+		if (conf->flags & VXLAN_F_IPV6_LINKLOCAL) {
+			NL_SET_ERR_MSG(extack,
+				       "Local interface required for link-local local/remote addresses");
+			return -EINVAL;
+		}
+#endif
+
+		*lower = NULL;
+	}
+
+	if (!conf->dst_port) {
+		if (conf->flags & VXLAN_F_GPE)
+			conf->dst_port = htons(4790); /* IANA VXLAN-GPE port */
+		else
+			conf->dst_port = htons(vxlan_port);
+	}
+
+	if (!conf->age_interval)
+		conf->age_interval = FDB_AGE_DEFAULT;
+
+	list_for_each_entry(tmp, &vn->vxlan_list, next) {
+		if (tmp == old)
+			continue;
+
+		if (tmp->cfg.vni != conf->vni)
+			continue;
+		if (tmp->cfg.dst_port != conf->dst_port)
+			continue;
+		if ((tmp->cfg.flags & (VXLAN_F_RCV_FLAGS | VXLAN_F_IPV6)) !=
+		    (conf->flags & (VXLAN_F_RCV_FLAGS | VXLAN_F_IPV6)))
+			continue;
+
+		if ((conf->flags & VXLAN_F_IPV6_LINKLOCAL) &&
+		    tmp->cfg.remote_ifindex != conf->remote_ifindex)
+			continue;
+
+		NL_SET_ERR_MSG(extack,
+			       "A VXLAN device with the specified VNI already exists");
+		return -EEXIST;
+	}
+
+	return 0;
+}
+
+static void vxlan_config_apply(struct net_device *dev,
+			       struct vxlan_config *conf,
+			       struct net_device *lowerdev,
+			       struct net *src_net,
+			       bool changelink)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_rdst *dst = &vxlan->default_dst;
+	unsigned short needed_headroom = ETH_HLEN;
+	int max_mtu = ETH_MAX_MTU;
+	u32 flags = conf->flags;
+
+	if (!changelink) {
+		if (flags & VXLAN_F_GPE)
+			vxlan_raw_setup(dev);
+		else
+			vxlan_ether_setup(dev);
+
+		if (conf->mtu)
+			dev->mtu = conf->mtu;
+
+		vxlan->net = src_net;
+	}
+
+	dst->remote_vni = conf->vni;
+
+	memcpy(&dst->remote_ip, &conf->remote_ip, sizeof(conf->remote_ip));
+
+	if (lowerdev) {
+		dst->remote_ifindex = conf->remote_ifindex;
+
+		dev->gso_max_size = lowerdev->gso_max_size;
+		dev->gso_max_segs = lowerdev->gso_max_segs;
+
+		needed_headroom = lowerdev->hard_header_len;
+		needed_headroom += lowerdev->needed_headroom;
+
+		dev->needed_tailroom = lowerdev->needed_tailroom;
+
+		max_mtu = lowerdev->mtu - vxlan_headroom(flags);
+		if (max_mtu < ETH_MIN_MTU)
+			max_mtu = ETH_MIN_MTU;
+
+		if (!changelink && !conf->mtu)
+			dev->mtu = max_mtu;
+	}
+
+	if (dev->mtu > max_mtu)
+		dev->mtu = max_mtu;
+
+	if (flags & VXLAN_F_COLLECT_METADATA)
+		flags |= VXLAN_F_IPV6;
+	needed_headroom += vxlan_headroom(flags);
+	dev->needed_headroom = needed_headroom;
+
+	memcpy(&vxlan->cfg, conf, sizeof(*conf));
+}
+
+static int vxlan_dev_configure(struct net *src_net, struct net_device *dev,
+			       struct vxlan_config *conf, bool changelink,
+			       struct netlink_ext_ack *extack)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct net_device *lowerdev;
+	int ret;
+
+	ret = vxlan_config_validate(src_net, conf, &lowerdev, vxlan, extack);
+	if (ret)
+		return ret;
+
+	vxlan_config_apply(dev, conf, lowerdev, src_net, changelink);
+
+	return 0;
+}
+
+static int __vxlan_dev_create(struct net *net, struct net_device *dev,
+			      struct vxlan_config *conf,
+			      struct netlink_ext_ack *extack)
+{
+	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct net_device *remote_dev = NULL;
+	struct vxlan_fdb *f = NULL;
+	bool unregister = false;
+	struct vxlan_rdst *dst;
+	int err;
+
+	dst = &vxlan->default_dst;
+	err = vxlan_dev_configure(net, dev, conf, false, extack);
+	if (err)
+		return err;
+
+	dev->ethtool_ops = &vxlan_ethtool_ops;
+
+	/* create an fdb entry for a valid default destination */
+	if (!vxlan_addr_any(&dst->remote_ip)) {
+		err = vxlan_fdb_create(vxlan, all_zeros_mac,
+				       &dst->remote_ip,
+				       NUD_REACHABLE | NUD_PERMANENT,
+				       vxlan->cfg.dst_port,
+				       dst->remote_vni,
+				       dst->remote_vni,
+				       dst->remote_ifindex,
+				       NTF_SELF, 0, &f, extack);
+		if (err)
+			return err;
+	}
+
+	err = register_netdevice(dev);
+	if (err)
+		goto errout;
+	unregister = true;
+
+	if (dst->remote_ifindex) {
+		remote_dev = __dev_get_by_index(net, dst->remote_ifindex);
+		if (!remote_dev) {
+			err = -ENODEV;
+			goto errout;
+		}
+
+		err = netdev_upper_dev_link(remote_dev, dev, extack);
+		if (err)
+			goto errout;
+	}
+
+	err = rtnl_configure_link(dev, NULL);
+	if (err < 0)
+		goto unlink;
+
+	if (f) {
+		vxlan_fdb_insert(vxlan, all_zeros_mac, dst->remote_vni, f);
+
+		/* notify default fdb entry */
+		err = vxlan_fdb_notify(vxlan, f, first_remote_rtnl(f),
+				       RTM_NEWNEIGH, true, extack);
+		if (err) {
+			vxlan_fdb_destroy(vxlan, f, false, false);
+			if (remote_dev)
+				netdev_upper_dev_unlink(remote_dev, dev);
+			goto unregister;
+		}
+	}
+
+	list_add(&vxlan->next, &vn->vxlan_list);
+	if (remote_dev)
+		dst->remote_dev = remote_dev;
+	return 0;
+unlink:
+	if (remote_dev)
+		netdev_upper_dev_unlink(remote_dev, dev);
+errout:
+	/* unregister_netdevice() destroys the default FDB entry with deletion
+	 * notification. But the addition notification was not sent yet, so
+	 * destroy the entry by hand here.
+	 */
+	if (f)
+		__vxlan_fdb_free(f);
+unregister:
+	if (unregister)
+		unregister_netdevice(dev);
+	return err;
+}
+
+/* Set/clear flags based on attribute */
+static int vxlan_nl2flag(struct vxlan_config *conf, struct nlattr *tb[],
+			  int attrtype, unsigned long mask, bool changelink,
+			  bool changelink_supported,
+			  struct netlink_ext_ack *extack)
+{
+	unsigned long flags;
+
+	if (!tb[attrtype])
+		return 0;
+
+	if (changelink && !changelink_supported) {
+		vxlan_flag_attr_error(attrtype, extack);
+		return -EOPNOTSUPP;
+	}
+
+	if (vxlan_policy[attrtype].type == NLA_FLAG)
+		flags = conf->flags | mask;
+	else if (nla_get_u8(tb[attrtype]))
+		flags = conf->flags | mask;
+	else
+		flags = conf->flags & ~mask;
+
+	conf->flags = flags;
+
+	return 0;
+}
+
+static int vxlan_nl2conf(struct nlattr *tb[], struct nlattr *data[],
+			 struct net_device *dev, struct vxlan_config *conf,
+			 bool changelink, struct netlink_ext_ack *extack)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	int err = 0;
+
+	memset(conf, 0, sizeof(*conf));
+
+	/* if changelink operation, start with old existing cfg */
+	if (changelink)
+		memcpy(conf, &vxlan->cfg, sizeof(*conf));
+
+	if (data[IFLA_VXLAN_ID]) {
+		__be32 vni = cpu_to_be32(nla_get_u32(data[IFLA_VXLAN_ID]));
+
+		if (changelink && (vni != conf->vni)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_ID], "Cannot change VNI");
+			return -EOPNOTSUPP;
+		}
+		conf->vni = cpu_to_be32(nla_get_u32(data[IFLA_VXLAN_ID]));
+	}
+
+	if (data[IFLA_VXLAN_GROUP]) {
+		if (changelink && (conf->remote_ip.sa.sa_family != AF_INET)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_GROUP], "New group address family does not match old group");
+			return -EOPNOTSUPP;
+		}
+
+		conf->remote_ip.sin.sin_addr.s_addr = nla_get_in_addr(data[IFLA_VXLAN_GROUP]);
+		conf->remote_ip.sa.sa_family = AF_INET;
+	} else if (data[IFLA_VXLAN_GROUP6]) {
+		if (!IS_ENABLED(CONFIG_IPV6)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_GROUP6], "IPv6 support not enabled in the kernel");
+			return -EPFNOSUPPORT;
+		}
+
+		if (changelink && (conf->remote_ip.sa.sa_family != AF_INET6)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_GROUP6], "New group address family does not match old group");
+			return -EOPNOTSUPP;
+		}
+
+		conf->remote_ip.sin6.sin6_addr = nla_get_in6_addr(data[IFLA_VXLAN_GROUP6]);
+		conf->remote_ip.sa.sa_family = AF_INET6;
+	}
+
+	if (data[IFLA_VXLAN_FAN_MAP]) {
+		err = vxlan_parse_fan_map(data, vxlan);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_LOCAL]) {
+		if (changelink && (conf->saddr.sa.sa_family != AF_INET)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_LOCAL], "New local address family does not match old");
+			return -EOPNOTSUPP;
+		}
+
+		conf->saddr.sin.sin_addr.s_addr = nla_get_in_addr(data[IFLA_VXLAN_LOCAL]);
+		conf->saddr.sa.sa_family = AF_INET;
+	} else if (data[IFLA_VXLAN_LOCAL6]) {
+		if (!IS_ENABLED(CONFIG_IPV6)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_LOCAL6], "IPv6 support not enabled in the kernel");
+			return -EPFNOSUPPORT;
+		}
+
+		if (changelink && (conf->saddr.sa.sa_family != AF_INET6)) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_LOCAL6], "New local address family does not match old");
+			return -EOPNOTSUPP;
+		}
+
+		/* TODO: respect scope id */
+		conf->saddr.sin6.sin6_addr = nla_get_in6_addr(data[IFLA_VXLAN_LOCAL6]);
+		conf->saddr.sa.sa_family = AF_INET6;
+	}
+
+	if (data[IFLA_VXLAN_LINK])
+		conf->remote_ifindex = nla_get_u32(data[IFLA_VXLAN_LINK]);
+
+	if (data[IFLA_VXLAN_TOS])
+		conf->tos  = nla_get_u8(data[IFLA_VXLAN_TOS]);
+
+	if (data[IFLA_VXLAN_TTL])
+		conf->ttl = nla_get_u8(data[IFLA_VXLAN_TTL]);
+
+	if (data[IFLA_VXLAN_TTL_INHERIT]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_TTL_INHERIT,
+				    VXLAN_F_TTL_INHERIT, changelink, false,
+				    extack);
+		if (err)
+			return err;
+
+	}
+
+	if (data[IFLA_VXLAN_LABEL])
+		conf->label = nla_get_be32(data[IFLA_VXLAN_LABEL]) &
+			     IPV6_FLOWLABEL_MASK;
+
+	if (data[IFLA_VXLAN_LEARNING]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_LEARNING,
+				    VXLAN_F_LEARN, changelink, true,
+				    extack);
+		if (err)
+			return err;
+	} else if (!changelink) {
+		/* default to learn on a new device */
+		conf->flags |= VXLAN_F_LEARN;
+	}
+
+	if (data[IFLA_VXLAN_AGEING])
+		conf->age_interval = nla_get_u32(data[IFLA_VXLAN_AGEING]);
+
+	if (data[IFLA_VXLAN_PROXY]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_PROXY,
+				    VXLAN_F_PROXY, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_RSC]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_RSC,
+				    VXLAN_F_RSC, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_L2MISS]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_L2MISS,
+				    VXLAN_F_L2MISS, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_L3MISS]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_L3MISS,
+				    VXLAN_F_L3MISS, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_LIMIT]) {
+		if (changelink) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_LIMIT],
+					    "Cannot change limit");
+			return -EOPNOTSUPP;
+		}
+		conf->addrmax = nla_get_u32(data[IFLA_VXLAN_LIMIT]);
+	}
+
+	if (data[IFLA_VXLAN_COLLECT_METADATA]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_COLLECT_METADATA,
+				    VXLAN_F_COLLECT_METADATA, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_PORT_RANGE]) {
+		if (!changelink) {
+			const struct ifla_vxlan_port_range *p
+				= nla_data(data[IFLA_VXLAN_PORT_RANGE]);
+			conf->port_min = ntohs(p->low);
+			conf->port_max = ntohs(p->high);
+		} else {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_PORT_RANGE],
+					    "Cannot change port range");
+			return -EOPNOTSUPP;
+		}
+	}
+
+	if (data[IFLA_VXLAN_PORT]) {
+		if (changelink) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_PORT],
+					    "Cannot change port");
+			return -EOPNOTSUPP;
+		}
+		conf->dst_port = nla_get_be16(data[IFLA_VXLAN_PORT]);
+	}
+
+	if (data[IFLA_VXLAN_UDP_CSUM]) {
+		if (changelink) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_VXLAN_UDP_CSUM],
+					    "Cannot change UDP_CSUM flag");
+			return -EOPNOTSUPP;
+		}
+		if (!nla_get_u8(data[IFLA_VXLAN_UDP_CSUM]))
+			conf->flags |= VXLAN_F_UDP_ZERO_CSUM_TX;
+	}
+
+	if (data[IFLA_VXLAN_UDP_ZERO_CSUM6_TX]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_UDP_ZERO_CSUM6_TX,
+				    VXLAN_F_UDP_ZERO_CSUM6_TX, changelink,
+				    false, extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_UDP_ZERO_CSUM6_RX]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_UDP_ZERO_CSUM6_RX,
+				    VXLAN_F_UDP_ZERO_CSUM6_RX, changelink,
+				    false, extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_REMCSUM_TX]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_REMCSUM_TX,
+				    VXLAN_F_REMCSUM_TX, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_REMCSUM_RX]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_REMCSUM_RX,
+				    VXLAN_F_REMCSUM_RX, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_GBP]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_GBP,
+				    VXLAN_F_GBP, changelink, false, extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_GPE]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_GPE,
+				    VXLAN_F_GPE, changelink, false,
+				    extack);
+		if (err)
+			return err;
+	}
+
+	if (data[IFLA_VXLAN_REMCSUM_NOPARTIAL]) {
+		err = vxlan_nl2flag(conf, data, IFLA_VXLAN_REMCSUM_NOPARTIAL,
+				    VXLAN_F_REMCSUM_NOPARTIAL, changelink,
+				    false, extack);
+		if (err)
+			return err;
+	}
+
+	if (tb[IFLA_MTU]) {
+		if (changelink) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_MTU],
+					    "Cannot change mtu");
+			return -EOPNOTSUPP;
+		}
+		conf->mtu = nla_get_u32(tb[IFLA_MTU]);
+	}
+
+	if (data[IFLA_VXLAN_DF])
+		conf->df = nla_get_u8(data[IFLA_VXLAN_DF]);
+
+	return 0;
+}
+
+static int vxlan_newlink(struct net *src_net, struct net_device *dev,
+			 struct nlattr *tb[], struct nlattr *data[],
+			 struct netlink_ext_ack *extack)
+{
+	struct vxlan_config conf;
+	int err;
+
+	err = vxlan_nl2conf(tb, data, dev, &conf, false, extack);
+	if (err)
+		return err;
+
+	return __vxlan_dev_create(src_net, dev, &conf, extack);
+}
+
+static int vxlan_changelink(struct net_device *dev, struct nlattr *tb[],
+			    struct nlattr *data[],
+			    struct netlink_ext_ack *extack)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct net_device *lowerdev;
+	struct vxlan_config conf;
+	struct vxlan_rdst *dst;
+	int err;
+
+	dst = &vxlan->default_dst;
+	err = vxlan_nl2conf(tb, data, dev, &conf, true, extack);
+	if (err)
+		return err;
+
+	err = vxlan_config_validate(vxlan->net, &conf, &lowerdev,
+				    vxlan, extack);
+	if (err)
+		return err;
+
+	if (dst->remote_dev == lowerdev)
+		lowerdev = NULL;
+
+	err = netdev_adjacent_change_prepare(dst->remote_dev, lowerdev, dev,
+					     extack);
+	if (err)
+		return err;
+
+	/* handle default dst entry */
+	if (!vxlan_addr_equal(&conf.remote_ip, &dst->remote_ip)) {
+		u32 hash_index = fdb_head_index(vxlan, all_zeros_mac, conf.vni);
+
+		spin_lock_bh(&vxlan->hash_lock[hash_index]);
+		if (!vxlan_addr_any(&conf.remote_ip)) {
+			err = vxlan_fdb_update(vxlan, all_zeros_mac,
+					       &conf.remote_ip,
+					       NUD_REACHABLE | NUD_PERMANENT,
+					       NLM_F_APPEND | NLM_F_CREATE,
+					       vxlan->cfg.dst_port,
+					       conf.vni, conf.vni,
+					       conf.remote_ifindex,
+					       NTF_SELF, 0, true, extack);
+			if (err) {
+				spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+				netdev_adjacent_change_abort(dst->remote_dev,
+							     lowerdev, dev);
+				return err;
+			}
+		}
+		if (!vxlan_addr_any(&dst->remote_ip))
+			__vxlan_fdb_delete(vxlan, all_zeros_mac,
+					   dst->remote_ip,
+					   vxlan->cfg.dst_port,
+					   dst->remote_vni,
+					   dst->remote_vni,
+					   dst->remote_ifindex,
+					   true);
+		spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+	}
+
+	if (conf.age_interval != vxlan->cfg.age_interval)
+		mod_timer(&vxlan->age_timer, jiffies);
+
+	netdev_adjacent_change_commit(dst->remote_dev, lowerdev, dev);
+	if (lowerdev && lowerdev != dst->remote_dev)
+		dst->remote_dev = lowerdev;
+	vxlan_config_apply(dev, &conf, lowerdev, vxlan->net, true);
+	return 0;
+}
+
+static void vxlan_dellink(struct net_device *dev, struct list_head *head)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+
+	vxlan_flush(vxlan, true);
+
+	list_del(&vxlan->next);
+	unregister_netdevice_queue(dev, head);
+	if (vxlan->default_dst.remote_dev)
+		netdev_upper_dev_unlink(vxlan->default_dst.remote_dev, dev);
+}
+
+static size_t vxlan_get_size(const struct net_device *dev)
+{
+
+	return nla_total_size(sizeof(__u32)) +	/* IFLA_VXLAN_ID */
+		nla_total_size(sizeof(struct in6_addr)) + /* IFLA_VXLAN_GROUP{6} */
+		nla_total_size(sizeof(__u32)) +	/* IFLA_VXLAN_LINK */
+		nla_total_size(sizeof(struct in6_addr)) + /* IFLA_VXLAN_LOCAL{6} */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_TTL */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_TTL_INHERIT */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_TOS */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_DF */
+		nla_total_size(sizeof(__be32)) + /* IFLA_VXLAN_LABEL */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_LEARNING */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_PROXY */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_RSC */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_L2MISS */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_L3MISS */
+		nla_total_size(sizeof(__u8)) +	/* IFLA_VXLAN_COLLECT_METADATA */
+		nla_total_size(sizeof(__u32)) +	/* IFLA_VXLAN_AGEING */
+		nla_total_size(sizeof(__u32)) +	/* IFLA_VXLAN_LIMIT */
+		nla_total_size(sizeof(struct ifla_vxlan_port_range)) +
+		nla_total_size(sizeof(__be16)) + /* IFLA_VXLAN_PORT */
+		nla_total_size(sizeof(__u8)) + /* IFLA_VXLAN_UDP_CSUM */
+		nla_total_size(sizeof(__u8)) + /* IFLA_VXLAN_UDP_ZERO_CSUM6_TX */
+		nla_total_size(sizeof(__u8)) + /* IFLA_VXLAN_UDP_ZERO_CSUM6_RX */
+		nla_total_size(sizeof(__u8)) + /* IFLA_VXLAN_REMCSUM_TX */
+		nla_total_size(sizeof(__u8)) + /* IFLA_VXLAN_REMCSUM_RX */
+		nla_total_size(sizeof(struct ip_fan_map) * 256) +
+		0;
+}
+
+static int vxlan_fill_info(struct sk_buff *skb, const struct net_device *dev)
+{
+	const struct vxlan_dev *vxlan = netdev_priv(dev);
+	const struct vxlan_rdst *dst = &vxlan->default_dst;
+	struct ifla_vxlan_port_range ports = {
+		.low =  htons(vxlan->cfg.port_min),
+		.high = htons(vxlan->cfg.port_max),
+	};
+
+	if (nla_put_u32(skb, IFLA_VXLAN_ID, be32_to_cpu(dst->remote_vni)))
+		goto nla_put_failure;
+
+	if (!vxlan_addr_any(&dst->remote_ip)) {
+		if (dst->remote_ip.sa.sa_family == AF_INET) {
+			if (nla_put_in_addr(skb, IFLA_VXLAN_GROUP,
+					    dst->remote_ip.sin.sin_addr.s_addr))
+				goto nla_put_failure;
+#if IS_ENABLED(CONFIG_IPV6)
+		} else {
+			if (nla_put_in6_addr(skb, IFLA_VXLAN_GROUP6,
+					     &dst->remote_ip.sin6.sin6_addr))
+				goto nla_put_failure;
+#endif
+		}
+	}
+
+	if (dst->remote_ifindex && nla_put_u32(skb, IFLA_VXLAN_LINK, dst->remote_ifindex))
+		goto nla_put_failure;
+
+	if (!vxlan_addr_any(&vxlan->cfg.saddr)) {
+		if (vxlan->cfg.saddr.sa.sa_family == AF_INET) {
+			if (nla_put_in_addr(skb, IFLA_VXLAN_LOCAL,
+					    vxlan->cfg.saddr.sin.sin_addr.s_addr))
+				goto nla_put_failure;
+#if IS_ENABLED(CONFIG_IPV6)
+		} else {
+			if (nla_put_in6_addr(skb, IFLA_VXLAN_LOCAL6,
+					     &vxlan->cfg.saddr.sin6.sin6_addr))
+				goto nla_put_failure;
+#endif
+		}
+	}
+
+	if (fan_has_map(&vxlan->fan)) {
+		struct nlattr *fan_nest;
+		struct ip_fan_map *fan_map;
+
+		fan_nest = nla_nest_start(skb, IFLA_VXLAN_FAN_MAP);
+		if (!fan_nest)
+			goto nla_put_failure;
+		list_for_each_entry_rcu(fan_map, &vxlan->fan.fan_maps, list) {
+			struct ifla_fan_map map;
+
+			map.underlay = fan_map->underlay;
+			map.underlay_prefix = fan_map->underlay_prefix;
+			map.overlay = fan_map->overlay;
+			map.overlay_prefix = fan_map->overlay_prefix;
+			if (nla_put(skb, IFLA_FAN_MAPPING, sizeof(map), &map))
+				goto nla_put_failure;
+		}
+		nla_nest_end(skb, fan_nest);
+	}
+
+	if (nla_put_u8(skb, IFLA_VXLAN_TTL, vxlan->cfg.ttl) ||
+	    nla_put_u8(skb, IFLA_VXLAN_TTL_INHERIT,
+		       !!(vxlan->cfg.flags & VXLAN_F_TTL_INHERIT)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_TOS, vxlan->cfg.tos) ||
+	    nla_put_u8(skb, IFLA_VXLAN_DF, vxlan->cfg.df) ||
+	    nla_put_be32(skb, IFLA_VXLAN_LABEL, vxlan->cfg.label) ||
+	    nla_put_u8(skb, IFLA_VXLAN_LEARNING,
+		       !!(vxlan->cfg.flags & VXLAN_F_LEARN)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_PROXY,
+		       !!(vxlan->cfg.flags & VXLAN_F_PROXY)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_RSC,
+		       !!(vxlan->cfg.flags & VXLAN_F_RSC)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_L2MISS,
+		       !!(vxlan->cfg.flags & VXLAN_F_L2MISS)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_L3MISS,
+		       !!(vxlan->cfg.flags & VXLAN_F_L3MISS)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_COLLECT_METADATA,
+		       !!(vxlan->cfg.flags & VXLAN_F_COLLECT_METADATA)) ||
+	    nla_put_u32(skb, IFLA_VXLAN_AGEING, vxlan->cfg.age_interval) ||
+	    nla_put_u32(skb, IFLA_VXLAN_LIMIT, vxlan->cfg.addrmax) ||
+	    nla_put_be16(skb, IFLA_VXLAN_PORT, vxlan->cfg.dst_port) ||
+	    nla_put_u8(skb, IFLA_VXLAN_UDP_CSUM,
+		       !(vxlan->cfg.flags & VXLAN_F_UDP_ZERO_CSUM_TX)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_UDP_ZERO_CSUM6_TX,
+		       !!(vxlan->cfg.flags & VXLAN_F_UDP_ZERO_CSUM6_TX)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_UDP_ZERO_CSUM6_RX,
+		       !!(vxlan->cfg.flags & VXLAN_F_UDP_ZERO_CSUM6_RX)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_REMCSUM_TX,
+		       !!(vxlan->cfg.flags & VXLAN_F_REMCSUM_TX)) ||
+	    nla_put_u8(skb, IFLA_VXLAN_REMCSUM_RX,
+		       !!(vxlan->cfg.flags & VXLAN_F_REMCSUM_RX)))
+		goto nla_put_failure;
+
+	if (nla_put(skb, IFLA_VXLAN_PORT_RANGE, sizeof(ports), &ports))
+		goto nla_put_failure;
+
+	if (vxlan->cfg.flags & VXLAN_F_GBP &&
+	    nla_put_flag(skb, IFLA_VXLAN_GBP))
+		goto nla_put_failure;
+
+	if (vxlan->cfg.flags & VXLAN_F_GPE &&
+	    nla_put_flag(skb, IFLA_VXLAN_GPE))
+		goto nla_put_failure;
+
+	if (vxlan->cfg.flags & VXLAN_F_REMCSUM_NOPARTIAL &&
+	    nla_put_flag(skb, IFLA_VXLAN_REMCSUM_NOPARTIAL))
+		goto nla_put_failure;
+
+	return 0;
+
+nla_put_failure:
+	return -EMSGSIZE;
+}
+
+static struct net *vxlan_get_link_net(const struct net_device *dev)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+
+	return vxlan->net;
+}
+
+static struct rtnl_link_ops vxlan_link_ops __read_mostly = {
+	.kind		= "vxlan",
+	.maxtype	= IFLA_VXLAN_MAX,
+	.policy		= vxlan_policy,
+	.priv_size	= sizeof(struct vxlan_dev),
+	.setup		= vxlan_setup,
+	.validate	= vxlan_validate,
+	.newlink	= vxlan_newlink,
+	.changelink	= vxlan_changelink,
+	.dellink	= vxlan_dellink,
+	.get_size	= vxlan_get_size,
+	.fill_info	= vxlan_fill_info,
+	.get_link_net	= vxlan_get_link_net,
+};
+
+struct net_device *vxlan_dev_create(struct net *net, const char *name,
+				    u8 name_assign_type,
+				    struct vxlan_config *conf)
+{
+	struct nlattr *tb[IFLA_MAX + 1];
+	struct net_device *dev;
+	int err;
+
+	memset(&tb, 0, sizeof(tb));
+
+	dev = rtnl_create_link(net, name, name_assign_type,
+			       &vxlan_link_ops, tb, NULL);
+	if (IS_ERR(dev))
+		return dev;
+
+	err = __vxlan_dev_create(net, dev, conf, NULL);
+	if (err < 0) {
+		free_netdev(dev);
+		return ERR_PTR(err);
+	}
+
+	err = rtnl_configure_link(dev, NULL);
+	if (err < 0) {
+		LIST_HEAD(list_kill);
+
+		vxlan_dellink(dev, &list_kill);
+		unregister_netdevice_many(&list_kill);
+		return ERR_PTR(err);
+	}
+
+	return dev;
+}
+EXPORT_SYMBOL_GPL(vxlan_dev_create);
+
+static void vxlan_handle_lowerdev_unregister(struct vxlan_net *vn,
+					     struct net_device *dev)
+{
+	struct vxlan_dev *vxlan, *next;
+	LIST_HEAD(list_kill);
+
+	list_for_each_entry_safe(vxlan, next, &vn->vxlan_list, next) {
+		struct vxlan_rdst *dst = &vxlan->default_dst;
+
+		/* In case we created vxlan device with carrier
+		 * and we loose the carrier due to module unload
+		 * we also need to remove vxlan device. In other
+		 * cases, it's not necessary and remote_ifindex
+		 * is 0 here, so no matches.
+		 */
+		if (dst->remote_ifindex == dev->ifindex)
+			vxlan_dellink(vxlan->dev, &list_kill);
+	}
+
+	unregister_netdevice_many(&list_kill);
+}
+
+static int vxlan_netdevice_event(struct notifier_block *unused,
+				 unsigned long event, void *ptr)
+{
+	struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+	struct vxlan_net *vn = net_generic(dev_net(dev), vxlan_net_id);
+
+	if (event == NETDEV_UNREGISTER)
+		vxlan_handle_lowerdev_unregister(vn, dev);
+	else if (event == NETDEV_UDP_TUNNEL_PUSH_INFO)
+		vxlan_offload_rx_ports(dev, true);
+	else if (event == NETDEV_UDP_TUNNEL_DROP_INFO)
+		vxlan_offload_rx_ports(dev, false);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block vxlan_notifier_block __read_mostly = {
+	.notifier_call = vxlan_netdevice_event,
+};
+
+static void
+vxlan_fdb_offloaded_set(struct net_device *dev,
+			struct switchdev_notifier_vxlan_fdb_info *fdb_info)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_rdst *rdst;
+	struct vxlan_fdb *f;
+	u32 hash_index;
+
+	hash_index = fdb_head_index(vxlan, fdb_info->eth_addr, fdb_info->vni);
+
+	spin_lock_bh(&vxlan->hash_lock[hash_index]);
+
+	f = vxlan_find_mac(vxlan, fdb_info->eth_addr, fdb_info->vni);
+	if (!f)
+		goto out;
+
+	rdst = vxlan_fdb_find_rdst(f, &fdb_info->remote_ip,
+				   fdb_info->remote_port,
+				   fdb_info->remote_vni,
+				   fdb_info->remote_ifindex);
+	if (!rdst)
+		goto out;
+
+	rdst->offloaded = fdb_info->offloaded;
+
+out:
+	spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+}
+
+static int
+vxlan_fdb_external_learn_add(struct net_device *dev,
+			     struct switchdev_notifier_vxlan_fdb_info *fdb_info)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct netlink_ext_ack *extack;
+	u32 hash_index;
+	int err;
+
+	hash_index = fdb_head_index(vxlan, fdb_info->eth_addr, fdb_info->vni);
+	extack = switchdev_notifier_info_to_extack(&fdb_info->info);
+
+	spin_lock_bh(&vxlan->hash_lock[hash_index]);
+	err = vxlan_fdb_update(vxlan, fdb_info->eth_addr, &fdb_info->remote_ip,
+			       NUD_REACHABLE,
+			       NLM_F_CREATE | NLM_F_REPLACE,
+			       fdb_info->remote_port,
+			       fdb_info->vni,
+			       fdb_info->remote_vni,
+			       fdb_info->remote_ifindex,
+			       NTF_USE | NTF_SELF | NTF_EXT_LEARNED,
+			       0, false, extack);
+	spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+
+	return err;
+}
+
+static int
+vxlan_fdb_external_learn_del(struct net_device *dev,
+			     struct switchdev_notifier_vxlan_fdb_info *fdb_info)
+{
+	struct vxlan_dev *vxlan = netdev_priv(dev);
+	struct vxlan_fdb *f;
+	u32 hash_index;
+	int err = 0;
+
+	hash_index = fdb_head_index(vxlan, fdb_info->eth_addr, fdb_info->vni);
+	spin_lock_bh(&vxlan->hash_lock[hash_index]);
+
+	f = vxlan_find_mac(vxlan, fdb_info->eth_addr, fdb_info->vni);
+	if (!f)
+		err = -ENOENT;
+	else if (f->flags & NTF_EXT_LEARNED)
+		err = __vxlan_fdb_delete(vxlan, fdb_info->eth_addr,
+					 fdb_info->remote_ip,
+					 fdb_info->remote_port,
+					 fdb_info->vni,
+					 fdb_info->remote_vni,
+					 fdb_info->remote_ifindex,
+					 false);
+
+	spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+
+	return err;
+}
+
+static int vxlan_switchdev_event(struct notifier_block *unused,
+				 unsigned long event, void *ptr)
+{
+	struct net_device *dev = switchdev_notifier_info_to_dev(ptr);
+	struct switchdev_notifier_vxlan_fdb_info *fdb_info;
+	int err = 0;
+
+	switch (event) {
+	case SWITCHDEV_VXLAN_FDB_OFFLOADED:
+		vxlan_fdb_offloaded_set(dev, ptr);
+		break;
+	case SWITCHDEV_VXLAN_FDB_ADD_TO_BRIDGE:
+		fdb_info = ptr;
+		err = vxlan_fdb_external_learn_add(dev, fdb_info);
+		if (err) {
+			err = notifier_from_errno(err);
+			break;
+		}
+		fdb_info->offloaded = true;
+		vxlan_fdb_offloaded_set(dev, fdb_info);
+		break;
+	case SWITCHDEV_VXLAN_FDB_DEL_TO_BRIDGE:
+		fdb_info = ptr;
+		err = vxlan_fdb_external_learn_del(dev, fdb_info);
+		if (err) {
+			err = notifier_from_errno(err);
+			break;
+		}
+		fdb_info->offloaded = false;
+		vxlan_fdb_offloaded_set(dev, fdb_info);
+		break;
+	}
+
+	return err;
+}
+
+static struct notifier_block vxlan_switchdev_notifier_block __read_mostly = {
+	.notifier_call = vxlan_switchdev_event,
+};
+
+static void vxlan_fdb_nh_flush(struct nexthop *nh)
+{
+	struct vxlan_fdb *fdb;
+	struct vxlan_dev *vxlan;
+	u32 hash_index;
+
+	rcu_read_lock();
+	list_for_each_entry_rcu(fdb, &nh->fdb_list, nh_list) {
+		vxlan = rcu_dereference(fdb->vdev);
+		WARN_ON(!vxlan);
+		hash_index = fdb_head_index(vxlan, fdb->eth_addr,
+					    vxlan->default_dst.remote_vni);
+		spin_lock_bh(&vxlan->hash_lock[hash_index]);
+		if (!hlist_unhashed(&fdb->hlist))
+			vxlan_fdb_destroy(vxlan, fdb, false, false);
+		spin_unlock_bh(&vxlan->hash_lock[hash_index]);
+	}
+	rcu_read_unlock();
+}
+
+static int vxlan_nexthop_event(struct notifier_block *nb,
+			       unsigned long event, void *ptr)
+{
+	struct nh_notifier_info *info = ptr;
+	struct nexthop *nh;
+
+	if (event != NEXTHOP_EVENT_DEL)
+		return NOTIFY_DONE;
+
+	nh = nexthop_find_by_id(info->net, info->id);
+	if (!nh)
+		return NOTIFY_DONE;
+
+	vxlan_fdb_nh_flush(nh);
+
+	return NOTIFY_DONE;
+}
+
+static __net_init int vxlan_init_net(struct net *net)
+{
+	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+	unsigned int h;
+
+	INIT_LIST_HEAD(&vn->vxlan_list);
+	spin_lock_init(&vn->sock_lock);
+	vn->nexthop_notifier_block.notifier_call = vxlan_nexthop_event;
+
+	for (h = 0; h < PORT_HASH_SIZE; ++h)
+		INIT_HLIST_HEAD(&vn->sock_list[h]);
+
+	return register_nexthop_notifier(net, &vn->nexthop_notifier_block,
+					 NULL);
+}
+
+#ifdef CONFIG_SYSCTL
+static struct ctl_table_header *vxlan_fan_header;
+static unsigned int vxlan_fan_version = 4;
+
+static struct ctl_table vxlan_fan_sysctls[] = {
+	{
+		.procname	= "vxlan",
+		.data		= &vxlan_fan_version,
+		.maxlen		= sizeof(vxlan_fan_version),
+		.mode		= 0444,
+		.proc_handler	= proc_dointvec,
+	},
+	{},
+};
+#endif /* CONFIG_SYSCTL */
+
+static void vxlan_destroy_tunnels(struct net *net, struct list_head *head)
+{
+	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+	struct vxlan_dev *vxlan, *next;
+	struct net_device *dev, *aux;
+
+	for_each_netdev_safe(net, dev, aux)
+		if (dev->rtnl_link_ops == &vxlan_link_ops)
+			unregister_netdevice_queue(dev, head);
+
+	list_for_each_entry_safe(vxlan, next, &vn->vxlan_list, next) {
+		/* If vxlan->dev is in the same netns, it has already been added
+		 * to the list by the previous loop.
+		 */
+		if (!net_eq(dev_net(vxlan->dev), net))
+			unregister_netdevice_queue(vxlan->dev, head);
+	}
+
+}
+
+static void __net_exit vxlan_exit_batch_net(struct list_head *net_list)
+{
+	struct net *net;
+	LIST_HEAD(list);
+	unsigned int h;
+
+	list_for_each_entry(net, net_list, exit_list) {
+		struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+
+		unregister_nexthop_notifier(net, &vn->nexthop_notifier_block);
+	}
+	rtnl_lock();
+	list_for_each_entry(net, net_list, exit_list)
+		vxlan_destroy_tunnels(net, &list);
+
+	unregister_netdevice_many(&list);
+	rtnl_unlock();
+
+	list_for_each_entry(net, net_list, exit_list) {
+		struct vxlan_net *vn = net_generic(net, vxlan_net_id);
+
+		for (h = 0; h < PORT_HASH_SIZE; ++h)
+			WARN_ON_ONCE(!hlist_empty(&vn->sock_list[h]));
+	}
+}
+
+static struct pernet_operations vxlan_net_ops = {
+	.init = vxlan_init_net,
+	.exit_batch = vxlan_exit_batch_net,
+	.id   = &vxlan_net_id,
+	.size = sizeof(struct vxlan_net),
+};
+
+static int __init vxlan_init_module(void)
+{
+	int rc;
+
+	get_random_bytes(&vxlan_salt, sizeof(vxlan_salt));
+
+	rc = register_pernet_subsys(&vxlan_net_ops);
+	if (rc)
+		goto out1;
+
+	rc = register_netdevice_notifier(&vxlan_notifier_block);
+	if (rc)
+		goto out2;
+
+	rc = register_switchdev_notifier(&vxlan_switchdev_notifier_block);
+	if (rc)
+		goto out3;
+
+	rc = rtnl_link_register(&vxlan_link_ops);
+	if (rc)
+		goto out4;
+
+#ifdef CONFIG_SYSCTL
+	vxlan_fan_header = register_net_sysctl(&init_net, "net/fan",
+					      vxlan_fan_sysctls);
+	if (!vxlan_fan_header) {
+		rc = -ENOMEM;
+		goto sysctl_failed;
+	}
+#endif /* CONFIG_SYSCTL */
+
+	return 0;
+#ifdef CONFIG_SYSCTL
+sysctl_failed:
+	rtnl_link_unregister(&vxlan_link_ops);
+#endif /* CONFIG_SYSCTL */
+out4:
+	unregister_switchdev_notifier(&vxlan_switchdev_notifier_block);
+out3:
+	unregister_netdevice_notifier(&vxlan_notifier_block);
+out2:
+	unregister_pernet_subsys(&vxlan_net_ops);
+out1:
+	return rc;
+}
+late_initcall(vxlan_init_module);
+
+static void __exit vxlan_cleanup_module(void)
+{
+#ifdef CONFIG_SYSCTL
+	unregister_net_sysctl_table(vxlan_fan_header);
+#endif /* CONFIG_SYSCTL */
+	rtnl_link_unregister(&vxlan_link_ops);
+	unregister_switchdev_notifier(&vxlan_switchdev_notifier_block);
+	unregister_netdevice_notifier(&vxlan_notifier_block);
+	unregister_pernet_subsys(&vxlan_net_ops);
+	/* rcu_barrier() is called by netns */
+}
+module_exit(vxlan_cleanup_module);
+
+MODULE_LICENSE("GPL");
+MODULE_VERSION(VXLAN_VERSION);
+MODULE_AUTHOR("Stephen Hemminger <stephen@networkplumber.org>");
+MODULE_DESCRIPTION("Driver for VXLAN encapsulated traffic");
+MODULE_ALIAS_RTNL_LINK("vxlan");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wan/farsync.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wan/farsync.c
@@ -2545,6 +2545,7 @@
 		struct net_device *dev = port_to_dev(&card->ports[i]);
 
 		unregister_hdlc_device(dev);
+		free_netdev(dev);
 	}
 
 	fst_disable_intr(card);
@@ -2564,6 +2565,7 @@
 				  card->tx_dma_handle_card);
 	}
 	fst_card_array[card->card_no] = NULL;
+	kfree(card);
 }
 
 static struct pci_driver fst_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wan/fsl_ucc_hdlc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wan/fsl_ucc_hdlc.c
@@ -34,6 +34,8 @@
 #define TDM_PPPOHT_SLIC_MAXIN
 #define RX_BD_ERRORS (R_CD_S | R_OV_S | R_CR_S | R_AB_S | R_NO_S | R_LG_S)
 
+static int uhdlc_close(struct net_device *dev);
+
 static struct ucc_tdm_info utdm_primary_info = {
 	.uf_info = {
 		.tsa = 0,
@@ -705,6 +707,7 @@
 	hdlc_device *hdlc = dev_to_hdlc(dev);
 	struct ucc_hdlc_private *priv = hdlc->priv;
 	struct ucc_tdm *utdm = priv->utdm;
+	int rc = 0;
 
 	if (priv->hdlc_busy != 1) {
 		if (request_irq(priv->ut_info->uf_info.irq,
@@ -728,10 +731,13 @@
 		napi_enable(&priv->napi);
 		netdev_reset_queue(dev);
 		netif_start_queue(dev);
-		hdlc_open(dev);
+
+		rc = hdlc_open(dev);
+		if (rc)
+			uhdlc_close(dev);
 	}
 
-	return 0;
+	return rc;
 }
 
 static void uhdlc_memclean(struct ucc_hdlc_private *priv)
@@ -821,6 +827,8 @@
 	netdev_reset_queue(dev);
 	priv->hdlc_busy = 0;
 
+	hdlc_close(dev);
+
 	return 0;
 }
 
@@ -1241,9 +1249,11 @@
 free_dev:
 	free_netdev(dev);
 undo_uhdlc_init:
-	iounmap(utdm->siram);
+	if (utdm)
+		iounmap(utdm->siram);
 unmap_si_regs:
-	iounmap(utdm->si_regs);
+	if (utdm)
+		iounmap(utdm->si_regs);
 free_utdm:
 	if (uhdlc_priv->tsa)
 		kfree(utdm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wan/lapbether.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wan/lapbether.c
@@ -325,6 +325,7 @@
 
 	err = lapb_register(dev, &lapbeth_callbacks);
 	if (err != LAPB_OK) {
+		napi_disable(&lapbeth->napi);
 		pr_err("lapb_register error: %d\n", err);
 		return -ENODEV;
 	}
@@ -383,6 +384,9 @@
 
 	ASSERT_RTNL();
 
+	if (dev->type != ARPHRD_ETHER)
+		return -EINVAL;
+
 	ndev = alloc_netdev(sizeof(*lapbeth), "lapb%d", NET_NAME_UNKNOWN,
 			    lapbeth_setup);
 	if (!ndev)
@@ -446,7 +450,7 @@
 	if (dev_net(dev) != &init_net)
 		return NOTIFY_DONE;
 
-	if (!dev_is_ethdev(dev))
+	if (!dev_is_ethdev(dev) && !lapbeth_get_x25_dev(dev))
 		return NOTIFY_DONE;
 
 	switch (event) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/allowedips.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/allowedips.c
@@ -6,6 +6,8 @@
 #include "allowedips.h"
 #include "peer.h"
 
+enum { MAX_ALLOWEDIPS_DEPTH = 129 };
+
 static struct kmem_cache *node_cache;
 
 static void swap_endian(u8 *dst, const u8 *src, u8 bits)
@@ -13,8 +15,8 @@
 	if (bits == 32) {
 		*(u32 *)dst = be32_to_cpu(*(const __be32 *)src);
 	} else if (bits == 128) {
-		((u64 *)dst)[0] = be64_to_cpu(((const __be64 *)src)[0]);
-		((u64 *)dst)[1] = be64_to_cpu(((const __be64 *)src)[1]);
+		((u64 *)dst)[0] = get_unaligned_be64(src);
+		((u64 *)dst)[1] = get_unaligned_be64(src + 8);
 	}
 }
 
@@ -40,7 +42,8 @@
 		     struct allowedips_node __rcu *p, unsigned int *len)
 {
 	if (rcu_access_pointer(p)) {
-		WARN_ON(IS_ENABLED(DEBUG) && *len >= 128);
+		if (WARN_ON(IS_ENABLED(DEBUG) && *len >= MAX_ALLOWEDIPS_DEPTH))
+			return;
 		stack[(*len)++] = rcu_dereference_raw(p);
 	}
 }
@@ -52,7 +55,7 @@
 
 static void root_free_rcu(struct rcu_head *rcu)
 {
-	struct allowedips_node *node, *stack[128] = {
+	struct allowedips_node *node, *stack[MAX_ALLOWEDIPS_DEPTH] = {
 		container_of(rcu, struct allowedips_node, rcu) };
 	unsigned int len = 1;
 
@@ -65,7 +68,7 @@
 
 static void root_remove_peer_lists(struct allowedips_node *root)
 {
-	struct allowedips_node *node, *stack[128] = { root };
+	struct allowedips_node *node, *stack[MAX_ALLOWEDIPS_DEPTH] = { root };
 	unsigned int len = 1;
 
 	while (len > 0 && (node = stack[--len])) {
@@ -163,7 +166,7 @@
 	return exact;
 }
 
-static inline void connect_node(struct allowedips_node **parent, u8 bit, struct allowedips_node *node)
+static inline void connect_node(struct allowedips_node __rcu **parent, u8 bit, struct allowedips_node *node)
 {
 	node->parent_bit_packed = (unsigned long)parent | bit;
 	rcu_assign_pointer(*parent, node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/device.c
@@ -19,6 +19,7 @@
 #include <linux/if_arp.h>
 #include <linux/icmp.h>
 #include <linux/suspend.h>
+#include <net/dst_metadata.h>
 #include <net/icmp.h>
 #include <net/rtnetlink.h>
 #include <net/ip_tunnels.h>
@@ -98,6 +99,7 @@
 {
 	struct wg_device *wg = netdev_priv(dev);
 	struct wg_peer *peer;
+	struct sk_buff *skb;
 
 	mutex_lock(&wg->device_update_lock);
 	list_for_each_entry(peer, &wg->peer_list, peer_list) {
@@ -108,7 +110,9 @@
 		wg_noise_reset_last_sent_handshake(&peer->last_sent_handshake);
 	}
 	mutex_unlock(&wg->device_update_lock);
-	skb_queue_purge(&wg->incoming_handshakes);
+	while ((skb = ptr_ring_consume(&wg->handshake_queue.ring)) != NULL)
+		kfree_skb(skb);
+	atomic_set(&wg->handshake_queue_len, 0);
 	wg_socket_reinit(wg, NULL, NULL);
 	return 0;
 }
@@ -149,7 +153,7 @@
 		goto err_peer;
 	}
 
-	mtu = skb_dst(skb) ? dst_mtu(skb_dst(skb)) : dev->mtu;
+	mtu = skb_valid_dst(skb) ? dst_mtu(skb_dst(skb)) : dev->mtu;
 
 	__skb_queue_head_init(&packets);
 	if (!skb_is_gso(skb)) {
@@ -189,7 +193,7 @@
 	 */
 	while (skb_queue_len(&peer->staged_packet_queue) > MAX_STAGED_PACKETS) {
 		dev_kfree_skb(__skb_dequeue(&peer->staged_packet_queue));
-		++dev->stats.tx_dropped;
+		DEV_STATS_INC(dev, tx_dropped);
 	}
 	skb_queue_splice_tail(&packets, &peer->staged_packet_queue);
 	spin_unlock_bh(&peer->staged_packet_queue.lock);
@@ -207,7 +211,7 @@
 	else if (skb->protocol == htons(ETH_P_IPV6))
 		icmpv6_ndo_send(skb, ICMPV6_DEST_UNREACH, ICMPV6_ADDR_UNREACH, 0);
 err:
-	++dev->stats.tx_errors;
+	DEV_STATS_INC(dev, tx_errors);
 	kfree_skb(skb);
 	return ret;
 }
@@ -235,14 +239,13 @@
 	destroy_workqueue(wg->handshake_receive_wq);
 	destroy_workqueue(wg->handshake_send_wq);
 	destroy_workqueue(wg->packet_crypt_wq);
-	wg_packet_queue_free(&wg->decrypt_queue);
-	wg_packet_queue_free(&wg->encrypt_queue);
+	wg_packet_queue_free(&wg->handshake_queue, true);
+	wg_packet_queue_free(&wg->decrypt_queue, false);
+	wg_packet_queue_free(&wg->encrypt_queue, false);
 	rcu_barrier(); /* Wait for all the peers to be actually freed. */
 	wg_ratelimiter_uninit();
 	memzero_explicit(&wg->static_identity, sizeof(wg->static_identity));
-	skb_queue_purge(&wg->incoming_handshakes);
 	free_percpu(dev->tstats);
-	free_percpu(wg->incoming_handshakes_worker);
 	kvfree(wg->index_hashtable);
 	kvfree(wg->peer_hashtable);
 	mutex_unlock(&wg->device_update_lock);
@@ -298,7 +301,6 @@
 	init_rwsem(&wg->static_identity.lock);
 	mutex_init(&wg->socket_update_lock);
 	mutex_init(&wg->device_update_lock);
-	skb_queue_head_init(&wg->incoming_handshakes);
 	wg_allowedips_init(&wg->peer_allowedips);
 	wg_cookie_checker_init(&wg->cookie_checker, wg);
 	INIT_LIST_HEAD(&wg->peer_list);
@@ -316,16 +318,10 @@
 	if (!dev->tstats)
 		goto err_free_index_hashtable;
 
-	wg->incoming_handshakes_worker =
-		wg_packet_percpu_multicore_worker_alloc(
-				wg_packet_handshake_receive_worker, wg);
-	if (!wg->incoming_handshakes_worker)
-		goto err_free_tstats;
-
 	wg->handshake_receive_wq = alloc_workqueue("wg-kex-%s",
 			WQ_CPU_INTENSIVE | WQ_FREEZABLE, 0, dev->name);
 	if (!wg->handshake_receive_wq)
-		goto err_free_incoming_handshakes;
+		goto err_free_tstats;
 
 	wg->handshake_send_wq = alloc_workqueue("wg-kex-%s",
 			WQ_UNBOUND | WQ_FREEZABLE, 0, dev->name);
@@ -347,10 +343,15 @@
 	if (ret < 0)
 		goto err_free_encrypt_queue;
 
-	ret = wg_ratelimiter_init();
+	ret = wg_packet_queue_init(&wg->handshake_queue, wg_packet_handshake_receive_worker,
+				   MAX_QUEUED_INCOMING_HANDSHAKES);
 	if (ret < 0)
 		goto err_free_decrypt_queue;
 
+	ret = wg_ratelimiter_init();
+	if (ret < 0)
+		goto err_free_handshake_queue;
+
 	ret = register_netdevice(dev);
 	if (ret < 0)
 		goto err_uninit_ratelimiter;
@@ -367,18 +368,18 @@
 
 err_uninit_ratelimiter:
 	wg_ratelimiter_uninit();
+err_free_handshake_queue:
+	wg_packet_queue_free(&wg->handshake_queue, false);
 err_free_decrypt_queue:
-	wg_packet_queue_free(&wg->decrypt_queue);
+	wg_packet_queue_free(&wg->decrypt_queue, false);
 err_free_encrypt_queue:
-	wg_packet_queue_free(&wg->encrypt_queue);
+	wg_packet_queue_free(&wg->encrypt_queue, false);
 err_destroy_packet_crypt:
 	destroy_workqueue(wg->packet_crypt_wq);
 err_destroy_handshake_send:
 	destroy_workqueue(wg->handshake_send_wq);
 err_destroy_handshake_receive:
 	destroy_workqueue(wg->handshake_receive_wq);
-err_free_incoming_handshakes:
-	free_percpu(wg->incoming_handshakes_worker);
 err_free_tstats:
 	free_percpu(dev->tstats);
 err_free_index_hashtable:
@@ -398,6 +399,7 @@
 static void wg_netns_pre_exit(struct net *net)
 {
 	struct wg_device *wg;
+	struct wg_peer *peer;
 
 	rtnl_lock();
 	list_for_each_entry(wg, &device_list, device_list) {
@@ -407,6 +409,8 @@
 			mutex_lock(&wg->device_update_lock);
 			rcu_assign_pointer(wg->creating_net, NULL);
 			wg_socket_reinit(wg, NULL, NULL);
+			list_for_each_entry(peer, &wg->peer_list, peer_list)
+				wg_socket_clear_peer_endpoint_src(peer);
 			mutex_unlock(&wg->device_update_lock);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/device.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/device.h
@@ -39,21 +39,18 @@
 
 struct wg_device {
 	struct net_device *dev;
-	struct crypt_queue encrypt_queue, decrypt_queue;
+	struct crypt_queue encrypt_queue, decrypt_queue, handshake_queue;
 	struct sock __rcu *sock4, *sock6;
 	struct net __rcu *creating_net;
 	struct noise_static_identity static_identity;
-	struct workqueue_struct *handshake_receive_wq, *handshake_send_wq;
-	struct workqueue_struct *packet_crypt_wq;
-	struct sk_buff_head incoming_handshakes;
-	int incoming_handshake_cpu;
-	struct multicore_worker __percpu *incoming_handshakes_worker;
+	struct workqueue_struct *packet_crypt_wq,*handshake_receive_wq, *handshake_send_wq;
 	struct cookie_checker cookie_checker;
 	struct pubkey_hashtable *peer_hashtable;
 	struct index_hashtable *index_hashtable;
 	struct allowedips peer_allowedips;
 	struct mutex device_update_lock, socket_update_lock;
 	struct list_head device_list, peer_list;
+	atomic_t handshake_queue_len;
 	unsigned int num_peers, device_update_gen;
 	u32 fwmark;
 	u16 incoming_port;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/netlink.c
@@ -164,8 +164,8 @@
 	if (!allowedips_node)
 		goto no_allowedips;
 	if (!ctx->allowedips_seq)
-		ctx->allowedips_seq = peer->device->peer_allowedips.seq;
-	else if (ctx->allowedips_seq != peer->device->peer_allowedips.seq)
+		ctx->allowedips_seq = ctx->wg->peer_allowedips.seq;
+	else if (ctx->allowedips_seq != ctx->wg->peer_allowedips.seq)
 		goto no_allowedips;
 
 	allowedips_nest = nla_nest_start(skb, WGPEER_A_ALLOWEDIPS);
@@ -255,17 +255,17 @@
 	if (!peers_nest)
 		goto out;
 	ret = 0;
-	/* If the last cursor was removed via list_del_init in peer_remove, then
+	lockdep_assert_held(&wg->device_update_lock);
+	/* If the last cursor was removed in peer_remove or peer_remove_all, then
 	 * we just treat this the same as there being no more peers left. The
 	 * reason is that seq_nr should indicate to userspace that this isn't a
 	 * coherent dump anyway, so they'll try again.
 	 */
 	if (list_empty(&wg->peer_list) ||
-	    (ctx->next_peer && list_empty(&ctx->next_peer->peer_list))) {
+	    (ctx->next_peer && ctx->next_peer->is_dead)) {
 		nla_nest_cancel(skb, peers_nest);
 		goto out;
 	}
-	lockdep_assert_held(&wg->device_update_lock);
 	peer = list_prepare_entry(ctx->next_peer, &wg->peer_list, peer_list);
 	list_for_each_entry_continue(peer, &wg->peer_list, peer_list) {
 		if (get_peer(peer, skb, ctx)) {
@@ -436,14 +436,13 @@
 	if (attrs[WGPEER_A_ENDPOINT]) {
 		struct sockaddr *addr = nla_data(attrs[WGPEER_A_ENDPOINT]);
 		size_t len = nla_len(attrs[WGPEER_A_ENDPOINT]);
+		struct endpoint endpoint = { { { 0 } } };
 
-		if ((len == sizeof(struct sockaddr_in) &&
-		     addr->sa_family == AF_INET) ||
-		    (len == sizeof(struct sockaddr_in6) &&
-		     addr->sa_family == AF_INET6)) {
-			struct endpoint endpoint = { { { 0 } } };
-
-			memcpy(&endpoint.addr, addr, len);
+		if (len == sizeof(struct sockaddr_in) && addr->sa_family == AF_INET) {
+			endpoint.addr4 = *(struct sockaddr_in *)addr;
+			wg_socket_set_peer_endpoint(peer, &endpoint);
+		} else if (len == sizeof(struct sockaddr_in6) && addr->sa_family == AF_INET6) {
+			endpoint.addr6 = *(struct sockaddr_in6 *)addr;
 			wg_socket_set_peer_endpoint(peer, &endpoint);
 		}
 	}
@@ -547,6 +546,7 @@
 		u8 *private_key = nla_data(info->attrs[WGDEVICE_A_PRIVATE_KEY]);
 		u8 public_key[NOISE_PUBLIC_KEY_LEN];
 		struct wg_peer *peer, *temp;
+		bool send_staged_packets;
 
 		if (!crypto_memneq(wg->static_identity.static_private,
 				   private_key, NOISE_PUBLIC_KEY_LEN))
@@ -565,14 +565,17 @@
 		}
 
 		down_write(&wg->static_identity.lock);
-		wg_noise_set_static_identity_private_key(&wg->static_identity,
-							 private_key);
-		list_for_each_entry_safe(peer, temp, &wg->peer_list,
-					 peer_list) {
+		send_staged_packets = !wg->static_identity.has_identity && netif_running(wg->dev);
+		wg_noise_set_static_identity_private_key(&wg->static_identity, private_key);
+		send_staged_packets = send_staged_packets && wg->static_identity.has_identity;
+
+		wg_cookie_checker_precompute_device_keys(&wg->cookie_checker);
+		list_for_each_entry_safe(peer, temp, &wg->peer_list, peer_list) {
 			wg_noise_precompute_static_static(peer);
 			wg_noise_expire_current_peer_keypairs(peer);
+			if (send_staged_packets)
+				wg_packet_send_staged_packets(peer);
 		}
-		wg_cookie_checker_precompute_device_keys(&wg->cookie_checker);
 		up_write(&wg->static_identity.lock);
 	}
 skip_set_private_key:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/noise.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/noise.c
@@ -302,6 +302,41 @@
 		static_identity->static_public, private_key);
 }
 
+static void hmac(u8 *out, const u8 *in, const u8 *key, const size_t inlen, const size_t keylen)
+{
+	struct blake2s_state state;
+	u8 x_key[BLAKE2S_BLOCK_SIZE] __aligned(__alignof__(u32)) = { 0 };
+	u8 i_hash[BLAKE2S_HASH_SIZE] __aligned(__alignof__(u32));
+	int i;
+
+	if (keylen > BLAKE2S_BLOCK_SIZE) {
+		blake2s_init(&state, BLAKE2S_HASH_SIZE);
+		blake2s_update(&state, key, keylen);
+		blake2s_final(&state, x_key);
+	} else
+		memcpy(x_key, key, keylen);
+
+	for (i = 0; i < BLAKE2S_BLOCK_SIZE; ++i)
+		x_key[i] ^= 0x36;
+
+	blake2s_init(&state, BLAKE2S_HASH_SIZE);
+	blake2s_update(&state, x_key, BLAKE2S_BLOCK_SIZE);
+	blake2s_update(&state, in, inlen);
+	blake2s_final(&state, i_hash);
+
+	for (i = 0; i < BLAKE2S_BLOCK_SIZE; ++i)
+		x_key[i] ^= 0x5c ^ 0x36;
+
+	blake2s_init(&state, BLAKE2S_HASH_SIZE);
+	blake2s_update(&state, x_key, BLAKE2S_BLOCK_SIZE);
+	blake2s_update(&state, i_hash, BLAKE2S_HASH_SIZE);
+	blake2s_final(&state, i_hash);
+
+	memcpy(out, i_hash, BLAKE2S_HASH_SIZE);
+	memzero_explicit(x_key, BLAKE2S_BLOCK_SIZE);
+	memzero_explicit(i_hash, BLAKE2S_HASH_SIZE);
+}
+
 /* This is Hugo Krawczyk's HKDF:
  *  - https://eprint.iacr.org/2010/264.pdf
  *  - https://tools.ietf.org/html/rfc5869
@@ -322,14 +357,14 @@
 		 ((third_len || third_dst) && (!second_len || !second_dst))));
 
 	/* Extract entropy from data into secret */
-	blake2s256_hmac(secret, data, chaining_key, data_len, NOISE_HASH_LEN);
+	hmac(secret, data, chaining_key, data_len, NOISE_HASH_LEN);
 
 	if (!first_dst || !first_len)
 		goto out;
 
 	/* Expand first key: key = secret, data = 0x1 */
 	output[0] = 1;
-	blake2s256_hmac(output, output, secret, 1, BLAKE2S_HASH_SIZE);
+	hmac(output, output, secret, 1, BLAKE2S_HASH_SIZE);
 	memcpy(first_dst, output, first_len);
 
 	if (!second_dst || !second_len)
@@ -337,8 +372,7 @@
 
 	/* Expand second key: key = secret, data = first-key || 0x2 */
 	output[BLAKE2S_HASH_SIZE] = 2;
-	blake2s256_hmac(output, output, secret, BLAKE2S_HASH_SIZE + 1,
-			BLAKE2S_HASH_SIZE);
+	hmac(output, output, secret, BLAKE2S_HASH_SIZE + 1, BLAKE2S_HASH_SIZE);
 	memcpy(second_dst, output, second_len);
 
 	if (!third_dst || !third_len)
@@ -346,8 +380,7 @@
 
 	/* Expand third key: key = secret, data = second-key || 0x3 */
 	output[BLAKE2S_HASH_SIZE] = 3;
-	blake2s256_hmac(output, output, secret, BLAKE2S_HASH_SIZE + 1,
-			BLAKE2S_HASH_SIZE);
+	hmac(output, output, secret, BLAKE2S_HASH_SIZE + 1, BLAKE2S_HASH_SIZE);
 	memcpy(third_dst, output, third_len);
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/queueing.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/queueing.c
@@ -4,6 +4,7 @@
  */
 
 #include "queueing.h"
+#include <linux/skb_array.h>
 
 struct multicore_worker __percpu *
 wg_packet_percpu_multicore_worker_alloc(work_func_t function, void *ptr)
@@ -27,6 +28,7 @@
 	int ret;
 
 	memset(queue, 0, sizeof(*queue));
+	queue->last_cpu = -1;
 	ret = ptr_ring_init(&queue->ring, len, GFP_KERNEL);
 	if (ret)
 		return ret;
@@ -38,11 +40,11 @@
 	return 0;
 }
 
-void wg_packet_queue_free(struct crypt_queue *queue)
+void wg_packet_queue_free(struct crypt_queue *queue, bool purge)
 {
 	free_percpu(queue->worker);
-	WARN_ON(!__ptr_ring_empty(&queue->ring));
-	ptr_ring_cleanup(&queue->ring, NULL);
+	WARN_ON(!purge && !__ptr_ring_empty(&queue->ring));
+	ptr_ring_cleanup(&queue->ring, purge ? __skb_array_destroy_skb : NULL);
 }
 
 #define NEXT(skb) ((skb)->prev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/queueing.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/queueing.h
@@ -23,7 +23,7 @@
 /* queueing.c APIs: */
 int wg_packet_queue_init(struct crypt_queue *queue, work_func_t function,
 			 unsigned int len);
-void wg_packet_queue_free(struct crypt_queue *queue);
+void wg_packet_queue_free(struct crypt_queue *queue, bool purge);
 struct multicore_worker __percpu *
 wg_packet_percpu_multicore_worker_alloc(work_func_t function, void *ptr);
 
@@ -119,20 +119,17 @@
 	return cpu;
 }
 
-/* This function is racy, in the sense that next is unlocked, so it could return
- * the same CPU twice. A race-free version of this would be to instead store an
- * atomic sequence number, do an increment-and-return, and then iterate through
- * every possible CPU until we get to that index -- choose_cpu. However that's
- * a bit slower, and it doesn't seem like this potential race actually
- * introduces any performance loss, so we live with it.
+/* This function is racy, in the sense that it's called while last_cpu is
+ * unlocked, so it could return the same CPU twice. Adding locking or using
+ * atomic sequence numbers is slower though, and the consequences of racing are
+ * harmless, so live with it.
  */
-static inline int wg_cpumask_next_online(int *next)
+static inline int wg_cpumask_next_online(int *last_cpu)
 {
-	int cpu = *next;
-
-	while (unlikely(!cpumask_test_cpu(cpu, cpu_online_mask)))
-		cpu = cpumask_next(cpu, cpu_online_mask) % nr_cpumask_bits;
-	*next = cpumask_next(cpu, cpu_online_mask) % nr_cpumask_bits;
+	int cpu = cpumask_next(READ_ONCE(*last_cpu), cpu_online_mask);
+	if (cpu >= nr_cpu_ids)
+		cpu = cpumask_first(cpu_online_mask);
+	WRITE_ONCE(*last_cpu, cpu);
 	return cpu;
 }
 
@@ -161,7 +158,7 @@
 
 static inline int wg_queue_enqueue_per_device_and_peer(
 	struct crypt_queue *device_queue, struct prev_queue *peer_queue,
-	struct sk_buff *skb, struct workqueue_struct *wq, int *next_cpu)
+	struct sk_buff *skb, struct workqueue_struct *wq)
 {
 	int cpu;
 
@@ -175,7 +172,7 @@
 	/* Then we queue it up in the device queue, which consumes the
 	 * packet as soon as it can.
 	 */
-	cpu = wg_cpumask_next_online(next_cpu);
+	cpu = wg_cpumask_next_online(&device_queue->last_cpu);
 	if (unlikely(ptr_ring_produce_bh(&device_queue->ring, skb)))
 		return -EPIPE;
 	queue_work_on(cpu, wq, &per_cpu_ptr(device_queue->worker, cpu)->work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/ratelimiter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/ratelimiter.c
@@ -176,12 +176,12 @@
 			(1U << 14) / sizeof(struct hlist_head)));
 	max_entries = table_size * 8;
 
-	table_v4 = kvzalloc(table_size * sizeof(*table_v4), GFP_KERNEL);
+	table_v4 = kvcalloc(table_size, sizeof(*table_v4), GFP_KERNEL);
 	if (unlikely(!table_v4))
 		goto err_kmemcache;
 
 #if IS_ENABLED(CONFIG_IPV6)
-	table_v6 = kvzalloc(table_size * sizeof(*table_v6), GFP_KERNEL);
+	table_v6 = kvcalloc(table_size, sizeof(*table_v6), GFP_KERNEL);
 	if (unlikely(!table_v6)) {
 		kvfree(table_v4);
 		goto err_kmemcache;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/receive.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/receive.c
@@ -116,8 +116,8 @@
 		return;
 	}
 
-	under_load = skb_queue_len(&wg->incoming_handshakes) >=
-		     MAX_QUEUED_INCOMING_HANDSHAKES / 8;
+	under_load = atomic_read(&wg->handshake_queue_len) >=
+			MAX_QUEUED_INCOMING_HANDSHAKES / 8;
 	if (under_load) {
 		last_under_load = ktime_get_coarse_boottime_ns();
 	} else if (last_under_load) {
@@ -212,13 +212,14 @@
 
 void wg_packet_handshake_receive_worker(struct work_struct *work)
 {
-	struct wg_device *wg = container_of(work, struct multicore_worker,
-					    work)->ptr;
+	struct crypt_queue *queue = container_of(work, struct multicore_worker, work)->ptr;
+	struct wg_device *wg = container_of(queue, struct wg_device, handshake_queue);
 	struct sk_buff *skb;
 
-	while ((skb = skb_dequeue(&wg->incoming_handshakes)) != NULL) {
+	while ((skb = ptr_ring_consume_bh(&queue->ring)) != NULL) {
 		wg_receive_handshake_packet(wg, skb);
 		dev_kfree_skb(skb);
+		atomic_dec(&wg->handshake_queue_len);
 		cond_resched();
 	}
 }
@@ -257,7 +258,7 @@
 
 	if (unlikely(!READ_ONCE(keypair->receiving.is_valid) ||
 		  wg_birthdate_has_expired(keypair->receiving.birthdate, REJECT_AFTER_TIME) ||
-		  keypair->receiving_counter.counter >= REJECT_AFTER_MESSAGES)) {
+		  READ_ONCE(keypair->receiving_counter.counter) >= REJECT_AFTER_MESSAGES)) {
 		WRITE_ONCE(keypair->receiving.is_valid, false);
 		return false;
 	}
@@ -324,7 +325,7 @@
 		for (i = 1; i <= top; ++i)
 			counter->backtrack[(i + index_current) &
 				((COUNTER_BITS_TOTAL / BITS_PER_LONG) - 1)] = 0;
-		counter->counter = their_counter;
+		WRITE_ONCE(counter->counter, their_counter);
 	}
 
 	index &= (COUNTER_BITS_TOTAL / BITS_PER_LONG) - 1;
@@ -422,20 +423,20 @@
 	net_dbg_skb_ratelimited("%s: Packet has unallowed src IP (%pISc) from peer %llu (%pISpfsc)\n",
 				dev->name, skb, peer->internal_id,
 				&peer->endpoint.addr);
-	++dev->stats.rx_errors;
-	++dev->stats.rx_frame_errors;
+	DEV_STATS_INC(dev, rx_errors);
+	DEV_STATS_INC(dev, rx_frame_errors);
 	goto packet_processed;
 dishonest_packet_type:
 	net_dbg_ratelimited("%s: Packet is neither ipv4 nor ipv6 from peer %llu (%pISpfsc)\n",
 			    dev->name, peer->internal_id, &peer->endpoint.addr);
-	++dev->stats.rx_errors;
-	++dev->stats.rx_frame_errors;
+	DEV_STATS_INC(dev, rx_errors);
+	DEV_STATS_INC(dev, rx_frame_errors);
 	goto packet_processed;
 dishonest_packet_size:
 	net_dbg_ratelimited("%s: Packet has incorrect size from peer %llu (%pISpfsc)\n",
 			    dev->name, peer->internal_id, &peer->endpoint.addr);
-	++dev->stats.rx_errors;
-	++dev->stats.rx_length_errors;
+	DEV_STATS_INC(dev, rx_errors);
+	DEV_STATS_INC(dev, rx_length_errors);
 	goto packet_processed;
 packet_processed:
 	dev_kfree_skb(skb);
@@ -469,7 +470,7 @@
 			net_dbg_ratelimited("%s: Packet has invalid nonce %llu (max %llu)\n",
 					    peer->device->dev->name,
 					    PACKET_CB(skb)->nonce,
-					    keypair->receiving_counter.counter);
+					    READ_ONCE(keypair->receiving_counter.counter));
 			goto next;
 		}
 
@@ -530,7 +531,7 @@
 		goto err;
 
 	ret = wg_queue_enqueue_per_device_and_peer(&wg->decrypt_queue, &peer->rx_queue, skb,
-						   wg->packet_crypt_wq, &wg->decrypt_queue.last_cpu);
+						   wg->packet_crypt_wq);
 	if (unlikely(ret == -EPIPE))
 		wg_queue_enqueue_per_peer_rx(skb, PACKET_STATE_DEAD);
 	if (likely(!ret || ret == -EPIPE)) {
@@ -553,22 +554,28 @@
 	case cpu_to_le32(MESSAGE_HANDSHAKE_INITIATION):
 	case cpu_to_le32(MESSAGE_HANDSHAKE_RESPONSE):
 	case cpu_to_le32(MESSAGE_HANDSHAKE_COOKIE): {
-		int cpu;
+		int cpu, ret = -EBUSY;
 
-		if (skb_queue_len(&wg->incoming_handshakes) >
-			    MAX_QUEUED_INCOMING_HANDSHAKES ||
-		    unlikely(!rng_is_initialized())) {
+		if (unlikely(!rng_is_initialized()))
+			goto drop;
+		if (atomic_read(&wg->handshake_queue_len) > MAX_QUEUED_INCOMING_HANDSHAKES / 2) {
+			if (spin_trylock_bh(&wg->handshake_queue.ring.producer_lock)) {
+				ret = __ptr_ring_produce(&wg->handshake_queue.ring, skb);
+				spin_unlock_bh(&wg->handshake_queue.ring.producer_lock);
+			}
+		} else
+			ret = ptr_ring_produce_bh(&wg->handshake_queue.ring, skb);
+		if (ret) {
+	drop:
 			net_dbg_skb_ratelimited("%s: Dropping handshake packet from %pISpfsc\n",
 						wg->dev->name, skb);
 			goto err;
 		}
-		skb_queue_tail(&wg->incoming_handshakes, skb);
-		/* Queues up a call to packet_process_queued_handshake_
-		 * packets(skb):
-		 */
-		cpu = wg_cpumask_next_online(&wg->incoming_handshake_cpu);
+		atomic_inc(&wg->handshake_queue_len);
+		cpu = wg_cpumask_next_online(&wg->handshake_queue.last_cpu);
+		/* Queues up a call to packet_process_queued_handshake_packets(skb): */
 		queue_work_on(cpu, wg->handshake_receive_wq,
-			&per_cpu_ptr(wg->incoming_handshakes_worker, cpu)->work);
+			      &per_cpu_ptr(wg->handshake_queue.worker, cpu)->work);
 		break;
 	}
 	case cpu_to_le32(MESSAGE_DATA):
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/selftest/allowedips.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/selftest/allowedips.c
@@ -593,16 +593,20 @@
 	wg_allowedips_remove_by_peer(&t, a, &mutex);
 	test_negative(4, a, 192, 168, 0, 1);
 
-	/* These will hit the WARN_ON(len >= 128) in free_node if something
-	 * goes wrong.
+	/* These will hit the WARN_ON(len >= MAX_ALLOWEDIPS_DEPTH) in free_node
+	 * if something goes wrong.
 	 */
-	for (i = 0; i < 128; ++i) {
-		part = cpu_to_be64(~(1LLU << (i % 64)));
-		memset(&ip, 0xff, 16);
-		memcpy((u8 *)&ip + (i < 64) * 8, &part, 8);
+	for (i = 0; i < 64; ++i) {
+		part = cpu_to_be64(~0LLU << i);
+		memset(&ip, 0xff, 8);
+		memcpy((u8 *)&ip + 8, &part, 8);
+		wg_allowedips_insert_v6(&t, &ip, 128, a, &mutex);
+		memcpy(&ip, &part, 8);
+		memset((u8 *)&ip + 8, 0, 8);
 		wg_allowedips_insert_v6(&t, &ip, 128, a, &mutex);
 	}
-
+	memset(&ip, 0, 16);
+	wg_allowedips_insert_v6(&t, &ip, 128, a, &mutex);
 	wg_allowedips_free(&t, &mutex);
 
 	wg_allowedips_init(&t);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/selftest/ratelimiter.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/selftest/ratelimiter.c
@@ -167,7 +167,7 @@
 	++test;
 #endif
 
-	for (trials = TRIALS_BEFORE_GIVING_UP;;) {
+	for (trials = TRIALS_BEFORE_GIVING_UP; IS_ENABLED(DEBUG_RATELIMITER_TIMINGS);) {
 		int test_count = 0, ret;
 
 		ret = timings_test(skb4, hdr4, skb6, hdr6, &test_count);
@@ -176,7 +176,6 @@
 				test += test_count;
 				goto err;
 			}
-			msleep(500);
 			continue;
 		} else if (ret < 0) {
 			test += test_count;
@@ -195,7 +194,6 @@
 				test += test_count;
 				goto err;
 			}
-			msleep(50);
 			continue;
 		}
 		test += test_count;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/send.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/send.c
@@ -222,7 +222,7 @@
 {
 	struct sk_buff *skb;
 
-	if (skb_queue_empty(&peer->staged_packet_queue)) {
+	if (skb_queue_empty_lockless(&peer->staged_packet_queue)) {
 		skb = alloc_skb(DATA_PACKET_HEAD_ROOM + MESSAGE_MINIMUM_LENGTH,
 				GFP_ATOMIC);
 		if (unlikely(!skb))
@@ -318,7 +318,7 @@
 		goto err;
 
 	ret = wg_queue_enqueue_per_device_and_peer(&wg->encrypt_queue, &peer->tx_queue, first,
-						   wg->packet_crypt_wq, &wg->encrypt_queue.last_cpu);
+						   wg->packet_crypt_wq);
 	if (unlikely(ret == -EPIPE))
 		wg_queue_enqueue_per_peer_tx(first, PACKET_STATE_DEAD);
 err:
@@ -333,7 +333,8 @@
 void wg_packet_purge_staged_packets(struct wg_peer *peer)
 {
 	spin_lock_bh(&peer->staged_packet_queue.lock);
-	peer->device->dev->stats.tx_dropped += peer->staged_packet_queue.qlen;
+	DEV_STATS_ADD(peer->device->dev, tx_dropped,
+		      peer->staged_packet_queue.qlen);
 	__skb_queue_purge(&peer->staged_packet_queue);
 	spin_unlock_bh(&peer->staged_packet_queue.lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/socket.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/socket.c
@@ -160,6 +160,7 @@
 	rcu_read_unlock_bh();
 	return ret;
 #else
+	kfree_skb(skb);
 	return -EAFNOSUPPORT;
 #endif
 }
@@ -241,7 +242,7 @@
 		endpoint->addr4.sin_addr.s_addr = ip_hdr(skb)->saddr;
 		endpoint->src4.s_addr = ip_hdr(skb)->daddr;
 		endpoint->src_if4 = skb->skb_iif;
-	} else if (skb->protocol == htons(ETH_P_IPV6)) {
+	} else if (IS_ENABLED(CONFIG_IPV6) && skb->protocol == htons(ETH_P_IPV6)) {
 		endpoint->addr6.sin6_family = AF_INET6;
 		endpoint->addr6.sin6_port = udp_hdr(skb)->source;
 		endpoint->addr6.sin6_addr = ipv6_hdr(skb)->saddr;
@@ -284,7 +285,7 @@
 		peer->endpoint.addr4 = endpoint->addr4;
 		peer->endpoint.src4 = endpoint->src4;
 		peer->endpoint.src_if4 = endpoint->src_if4;
-	} else if (endpoint->addr.sa_family == AF_INET6) {
+	} else if (IS_ENABLED(CONFIG_IPV6) && endpoint->addr.sa_family == AF_INET6) {
 		peer->endpoint.addr6 = endpoint->addr6;
 		peer->endpoint.src6 = endpoint->src6;
 	} else {
@@ -308,7 +309,7 @@
 {
 	write_lock_bh(&peer->endpoint_lock);
 	memset(&peer->endpoint.src6, 0, sizeof(peer->endpoint.src6));
-	dst_cache_reset(&peer->endpoint_cache);
+	dst_cache_reset_now(&peer->endpoint_cache);
 	write_unlock_bh(&peer->endpoint_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireguard/timers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireguard/timers.c
@@ -46,7 +46,7 @@
 	if (peer->timer_handshake_attempts > MAX_TIMER_HANDSHAKES) {
 		pr_debug("%s: Handshake for peer %llu (%pISpfsc) did not complete after %d attempts, giving up\n",
 			 peer->device->dev->name, peer->internal_id,
-			 &peer->endpoint.addr, MAX_TIMER_HANDSHAKES + 2);
+			 &peer->endpoint.addr, (int)MAX_TIMER_HANDSHAKES + 2);
 
 		del_timer(&peer->timer_send_keepalive);
 		/* We drop all packets without a keypair and don't try again,
@@ -64,7 +64,7 @@
 		++peer->timer_handshake_attempts;
 		pr_debug("%s: Handshake for peer %llu (%pISpfsc) did not complete after %d seconds, retrying (try %d)\n",
 			 peer->device->dev->name, peer->internal_id,
-			 &peer->endpoint.addr, REKEY_TIMEOUT,
+			 &peer->endpoint.addr, (int)REKEY_TIMEOUT,
 			 peer->timer_handshake_attempts + 1);
 
 		/* We clear the endpoint address src address, in case this is
@@ -94,7 +94,7 @@
 
 	pr_debug("%s: Retrying handshake with peer %llu (%pISpfsc) because we stopped hearing back after %d seconds\n",
 		 peer->device->dev->name, peer->internal_id,
-		 &peer->endpoint.addr, KEEPALIVE_TIMEOUT + REKEY_TIMEOUT);
+		 &peer->endpoint.addr, (int)(KEEPALIVE_TIMEOUT + REKEY_TIMEOUT));
 	/* We clear the endpoint address src address, in case this is the cause
 	 * of trouble.
 	 */
@@ -126,7 +126,7 @@
 
 	pr_debug("%s: Zeroing out all keys for peer %llu (%pISpfsc), since we haven't received a new one in %d seconds\n",
 		 peer->device->dev->name, peer->internal_id,
-		 &peer->endpoint.addr, REJECT_AFTER_TIME * 3);
+		 &peer->endpoint.addr, (int)REJECT_AFTER_TIME * 3);
 	wg_noise_handshake_clear(&peer->handshake);
 	wg_noise_keypairs_clear(&peer->keypairs);
 	wg_peer_put(peer);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ar5523/ar5523.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ar5523/ar5523.c
@@ -153,6 +153,10 @@
 			ar5523_err(ar, "Invalid reply to WDCMSG_TARGET_START");
 			return;
 		}
+		if (!cmd->odata) {
+			ar5523_err(ar, "Unexpected WDCMSG_TARGET_START reply");
+			return;
+		}
 		memcpy(cmd->odata, hdr + 1, sizeof(u32));
 		cmd->olen = sizeof(u32);
 		cmd->res = 0;
@@ -237,6 +241,11 @@
 	}
 }
 
+static void ar5523_cancel_tx_cmd(struct ar5523 *ar)
+{
+	usb_kill_urb(ar->tx_cmd.urb_tx);
+}
+
 static int ar5523_cmd(struct ar5523 *ar, u32 code, const void *idata,
 		      int ilen, void *odata, int olen, int flags)
 {
@@ -276,6 +285,7 @@
 	}
 
 	if (!wait_for_completion_timeout(&cmd->done, 2 * HZ)) {
+		ar5523_cancel_tx_cmd(ar);
 		cmd->odata = NULL;
 		ar5523_err(ar, "timeout waiting for command %02x reply\n",
 			   code);
@@ -1580,6 +1590,20 @@
 	struct ar5523 *ar;
 	int error = -ENOMEM;
 
+	static const u8 bulk_ep_addr[] = {
+		AR5523_CMD_TX_PIPE | USB_DIR_OUT,
+		AR5523_DATA_TX_PIPE | USB_DIR_OUT,
+		AR5523_CMD_RX_PIPE | USB_DIR_IN,
+		AR5523_DATA_RX_PIPE | USB_DIR_IN,
+		0};
+
+	if (!usb_check_bulk_endpoints(intf, bulk_ep_addr)) {
+		dev_err(&dev->dev,
+			"Could not find all expected endpoints\n");
+		error = -ENODEV;
+		goto out;
+	}
+
 	/*
 	 * Load firmware if the device requires it.  This will return
 	 * -ENXIO on success and we'll get called back afer the usb
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath.h
@@ -96,11 +96,13 @@
 	u8 kv_type;
 	u8 kv_pad;
 	u16 kv_len;
-	u8 kv_val[16]; /* TK */
-	u8 kv_mic[8]; /* Michael MIC key */
-	u8 kv_txmic[8]; /* Michael MIC TX key (used only if the hardware
-			 * supports both MIC keys in the same key cache entry;
-			 * in that case, kv_mic is the RX key) */
+	struct_group(kv_values,
+		u8 kv_val[16]; /* TK */
+		u8 kv_mic[8]; /* Michael MIC key */
+		u8 kv_txmic[8]; /* Michael MIC TX key (used only if the hardware
+				 * supports both MIC keys in the same key cache entry;
+				 * in that case, kv_mic is the RX key) */
+	);
 };
 
 enum ath_cipher {
@@ -169,8 +171,10 @@
 	unsigned int clockrate;
 
 	spinlock_t cc_lock;
-	struct ath_cycle_counters cc_ani;
-	struct ath_cycle_counters cc_survey;
+	struct_group(cc,
+		struct ath_cycle_counters cc_ani;
+		struct ath_cycle_counters cc_survey;
+	);
 
 	struct ath_regulatory regulatory;
 	struct ath_regulatory reg_world_copy;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/Kconfig
@@ -44,6 +44,7 @@
 	tristate "Qualcomm ath10k SNOC support"
 	depends on ATH10K
 	depends on ARCH_QCOM || COMPILE_TEST
+	depends on QCOM_RPROC_COMMON || QCOM_RPROC_COMMON=n
 	select QCOM_SCM
 	select QCOM_QMI_HELPERS
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/core.c
@@ -89,6 +89,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = true,
 		.dynamic_sar_support = false,
 	},
@@ -124,6 +125,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = true,
 		.dynamic_sar_support = false,
 	},
@@ -160,6 +162,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -190,6 +193,7 @@
 		.num_wds_entries = 0x20,
 		.uart_pin_workaround = true,
 		.tx_stats_over_pktlog = false,
+		.credit_size_workaround = false,
 		.bmi_large_size_download = true,
 		.supports_peer_stats_info = true,
 		.dynamic_sar_support = true,
@@ -226,6 +230,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -261,6 +266,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -296,6 +302,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -334,6 +341,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = true,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.supports_peer_stats_info = true,
 		.dynamic_sar_support = true,
@@ -376,6 +384,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -424,6 +433,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -469,6 +479,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -504,6 +515,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -541,6 +553,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = true,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -570,6 +583,7 @@
 		.ast_skid_limit = 0x10,
 		.num_wds_entries = 0x20,
 		.uart_pin_workaround = true,
+		.credit_size_workaround = true,
 		.dynamic_sar_support = false,
 	},
 	{
@@ -611,6 +625,7 @@
 		.rri_on_ddr = false,
 		.hw_filter_reset_required = true,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = false,
 	},
@@ -625,6 +640,9 @@
 		.max_spatial_stream = 4,
 		.fw = {
 			.dir = WCN3990_HW_1_0_FW_DIR,
+			.board = WCN3990_HW_1_0_BOARD_DATA_FILE,
+			.board_size = WCN3990_BOARD_DATA_SZ,
+			.board_ext_size = WCN3990_BOARD_EXT_DATA_SZ,
 		},
 		.sw_decrypt_mcast_mgmt = true,
 		.hw_ops = &wcn3990_ops,
@@ -639,6 +657,7 @@
 		.rri_on_ddr = true,
 		.hw_filter_reset_required = false,
 		.fw_diag_ce_download = false,
+		.credit_size_workaround = false,
 		.tx_stats_over_pktlog = false,
 		.dynamic_sar_support = true,
 	},
@@ -714,6 +733,7 @@
 
 static int ath10k_init_sdio(struct ath10k *ar, enum ath10k_firmware_mode mode)
 {
+	bool mtu_workaround = ar->hw_params.credit_size_workaround;
 	int ret;
 	u32 param = 0;
 
@@ -731,7 +751,7 @@
 
 	param |= HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_SET;
 
-	if (mode == ATH10K_FIRMWARE_MODE_NORMAL)
+	if (mode == ATH10K_FIRMWARE_MODE_NORMAL && !mtu_workaround)
 		param |= HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE;
 	else
 		param &= ~HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE;
@@ -2690,9 +2710,16 @@
 	int i, ret;
 	u32 len, remaining_len;
 
-	hw_mem = ath10k_coredump_get_mem_layout(ar);
+	/* copy target iram feature must work also when
+	 * ATH10K_FW_CRASH_DUMP_RAM_DATA is disabled, so
+	 * _ath10k_coredump_get_mem_layout() to accomplist that
+	 */
+	hw_mem = _ath10k_coredump_get_mem_layout(ar);
 	if (!hw_mem)
-		return -ENOMEM;
+		/* if CONFIG_DEV_COREDUMP is disabled we get NULL, then
+		 * just silently disable the feature by doing nothing
+		 */
+		return 0;
 
 	for (i = 0; i < hw_mem->region_table.size; i++) {
 		tmp = &hw_mem->region_table.regions[i];
@@ -3520,13 +3547,10 @@
 
 void ath10k_core_destroy(struct ath10k *ar)
 {
-	flush_workqueue(ar->workqueue);
 	destroy_workqueue(ar->workqueue);
 
-	flush_workqueue(ar->workqueue_aux);
 	destroy_workqueue(ar->workqueue_aux);
 
-	flush_workqueue(ar->workqueue_tx_complete);
 	destroy_workqueue(ar->workqueue_tx_complete);
 
 	ath10k_debug_destroy(ar);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/coredump.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/coredump.c
@@ -1447,11 +1447,17 @@
 
 const struct ath10k_hw_mem_layout *ath10k_coredump_get_mem_layout(struct ath10k *ar)
 {
-	int i;
-
 	if (!test_bit(ATH10K_FW_CRASH_DUMP_RAM_DATA, &ath10k_coredump_mask))
 		return NULL;
 
+	return _ath10k_coredump_get_mem_layout(ar);
+}
+EXPORT_SYMBOL(ath10k_coredump_get_mem_layout);
+
+const struct ath10k_hw_mem_layout *_ath10k_coredump_get_mem_layout(struct ath10k *ar)
+{
+	int i;
+
 	if (WARN_ON(ar->target_version == 0))
 		return NULL;
 
@@ -1464,7 +1470,6 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL(ath10k_coredump_get_mem_layout);
 
 struct ath10k_fw_crash_data *ath10k_coredump_new(struct ath10k *ar)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/coredump.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/coredump.h
@@ -176,6 +176,7 @@
 void ath10k_coredump_unregister(struct ath10k *ar);
 void ath10k_coredump_destroy(struct ath10k *ar);
 
+const struct ath10k_hw_mem_layout *_ath10k_coredump_get_mem_layout(struct ath10k *ar);
 const struct ath10k_hw_mem_layout *ath10k_coredump_get_mem_layout(struct ath10k *ar);
 
 #else /* CONFIG_DEV_COREDUMP */
@@ -213,6 +214,12 @@
 {
 	return NULL;
 }
+
+static inline const struct ath10k_hw_mem_layout *
+_ath10k_coredump_get_mem_layout(struct ath10k *ar)
+{
+	return NULL;
+}
 
 #endif /* CONFIG_DEV_COREDUMP */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/debug.c
@@ -1139,7 +1139,7 @@
 				 u32 sset, u8 *data)
 {
 	if (sset == ETH_SS_STATS)
-		memcpy(data, *ath10k_gstrings_stats,
+		memcpy(data, ath10k_gstrings_stats,
 		       sizeof(ath10k_gstrings_stats));
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/debugfs_sta.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/debugfs_sta.c
@@ -438,7 +438,7 @@
 	}
 out:
 	mutex_unlock(&ar->conf_mutex);
-	return count;
+	return ret ?: count;
 }
 
 static const struct file_operations fops_peer_debug_trigger = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -147,6 +147,9 @@
 	htt->num_pending_tx--;
 	if (htt->num_pending_tx == htt->max_num_pending_tx - 1)
 		ath10k_mac_tx_unlock(htt->ar, ATH10K_TX_PAUSE_Q_FULL);
+
+	if (htt->num_pending_tx == 0)
+		wake_up(&htt->empty_tx_wq);
 }
 
 int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/hw.h
@@ -132,6 +132,7 @@
 /* WCN3990 1.0 definitions */
 #define WCN3990_HW_1_0_DEV_VERSION	ATH10K_HW_WCN3990
 #define WCN3990_HW_1_0_FW_DIR		ATH10K_FW_DIR "/WCN3990/hw1.0"
+#define WCN3990_HW_1_0_BOARD_DATA_FILE "board.bin"
 
 #define ATH10K_FW_FILE_BASE		"firmware"
 #define ATH10K_FW_API_MAX		6
@@ -618,6 +619,9 @@
 	 */
 	bool uart_pin_workaround;
 
+	/* Workaround for the credit size calculation */
+	bool credit_size_workaround;
+
 	/* tx stats support over pktlog */
 	bool tx_stats_over_pktlog;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/mac.c
@@ -864,11 +864,36 @@
 	return 0;
 }
 
+static void ath10k_peer_map_cleanup(struct ath10k *ar, struct ath10k_peer *peer)
+{
+	int peer_id, i;
+
+	lockdep_assert_held(&ar->conf_mutex);
+
+	for_each_set_bit(peer_id, peer->peer_ids,
+			 ATH10K_MAX_NUM_PEER_IDS) {
+		ar->peer_map[peer_id] = NULL;
+	}
+
+	/* Double check that peer is properly un-referenced from
+	 * the peer_map
+	 */
+	for (i = 0; i < ARRAY_SIZE(ar->peer_map); i++) {
+		if (ar->peer_map[i] == peer) {
+			ath10k_warn(ar, "removing stale peer_map entry for %pM (ptr %pK idx %d)\n",
+				    peer->addr, peer, i);
+			ar->peer_map[i] = NULL;
+		}
+	}
+
+	list_del(&peer->list);
+	kfree(peer);
+	ar->num_peers--;
+}
+
 static void ath10k_peer_cleanup(struct ath10k *ar, u32 vdev_id)
 {
 	struct ath10k_peer *peer, *tmp;
-	int peer_id;
-	int i;
 
 	lockdep_assert_held(&ar->conf_mutex);
 
@@ -880,25 +905,7 @@
 		ath10k_warn(ar, "removing stale peer %pM from vdev_id %d\n",
 			    peer->addr, vdev_id);
 
-		for_each_set_bit(peer_id, peer->peer_ids,
-				 ATH10K_MAX_NUM_PEER_IDS) {
-			ar->peer_map[peer_id] = NULL;
-		}
-
-		/* Double check that peer is properly un-referenced from
-		 * the peer_map
-		 */
-		for (i = 0; i < ARRAY_SIZE(ar->peer_map); i++) {
-			if (ar->peer_map[i] == peer) {
-				ath10k_warn(ar, "removing stale peer_map entry for %pM (ptr %pK idx %d)\n",
-					    peer->addr, peer, i);
-				ar->peer_map[i] = NULL;
-			}
-		}
-
-		list_del(&peer->list);
-		kfree(peer);
-		ar->num_peers--;
+		ath10k_peer_map_cleanup(ar, peer);
 	}
 	spin_unlock_bh(&ar->data_lock);
 }
@@ -993,8 +1000,12 @@
 	ath10k_mac_vif_beacon_free(arvif);
 
 	if (arvif->beacon_buf) {
-		dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN,
-				  arvif->beacon_buf, arvif->beacon_paddr);
+		if (ar->bus_param.dev_type == ATH10K_DEV_TYPE_HL)
+			kfree(arvif->beacon_buf);
+		else
+			dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN,
+					  arvif->beacon_buf,
+					  arvif->beacon_paddr);
 		arvif->beacon_buf = NULL;
 	}
 }
@@ -1048,7 +1059,7 @@
 	arg.channel.min_power = 0;
 	arg.channel.max_power = channel->max_power * 2;
 	arg.channel.max_reg_power = channel->max_reg_power * 2;
-	arg.channel.max_antenna_gain = channel->max_antenna_gain * 2;
+	arg.channel.max_antenna_gain = channel->max_antenna_gain;
 
 	reinit_completion(&ar->vdev_setup_done);
 	reinit_completion(&ar->vdev_delete_done);
@@ -1494,7 +1505,7 @@
 	arg.channel.min_power = 0;
 	arg.channel.max_power = chandef->chan->max_power * 2;
 	arg.channel.max_reg_power = chandef->chan->max_reg_power * 2;
-	arg.channel.max_antenna_gain = chandef->chan->max_antenna_gain * 2;
+	arg.channel.max_antenna_gain = chandef->chan->max_antenna_gain;
 
 	if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
 		arg.ssid = arvif->u.ap.ssid;
@@ -3422,7 +3433,7 @@
 			ch->min_power = 0;
 			ch->max_power = channel->max_power * 2;
 			ch->max_reg_power = channel->max_reg_power * 2;
-			ch->max_antenna_gain = channel->max_antenna_gain * 2;
+			ch->max_antenna_gain = channel->max_antenna_gain;
 			ch->reg_class_id = 0; /* FIXME */
 
 			/* FIXME: why use only legacy modes, why not any
@@ -5335,13 +5346,29 @@
 static void ath10k_stop(struct ieee80211_hw *hw)
 {
 	struct ath10k *ar = hw->priv;
+	u32 opt;
 
 	ath10k_drain_tx(ar);
 
 	mutex_lock(&ar->conf_mutex);
 	if (ar->state != ATH10K_STATE_OFF) {
-		if (!ar->hw_rfkill_on)
-			ath10k_halt(ar);
+		if (!ar->hw_rfkill_on) {
+			/* If the current driver state is RESTARTING but not yet
+			 * fully RESTARTED because of incoming suspend event,
+			 * then ath10k_halt() is already called via
+			 * ath10k_core_restart() and should not be called here.
+			 */
+			if (ar->state != ATH10K_STATE_RESTARTING) {
+				ath10k_halt(ar);
+			} else {
+				/* Suspending here, because when in RESTARTING
+				 * state, ath10k_core_stop() skips
+				 * ath10k_wait_for_suspend().
+				 */
+				opt = WMI_PDEV_SUSPEND_AND_DISABLE_INTR;
+				ath10k_wait_for_suspend(ar, opt);
+			}
+		}
 		ar->state = ATH10K_STATE_OFF;
 	}
 	mutex_unlock(&ar->conf_mutex);
@@ -5576,10 +5603,25 @@
 	if (vif->type == NL80211_IFTYPE_ADHOC ||
 	    vif->type == NL80211_IFTYPE_MESH_POINT ||
 	    vif->type == NL80211_IFTYPE_AP) {
-		arvif->beacon_buf = dma_alloc_coherent(ar->dev,
-						       IEEE80211_MAX_FRAME_LEN,
-						       &arvif->beacon_paddr,
-						       GFP_ATOMIC);
+		if (ar->bus_param.dev_type == ATH10K_DEV_TYPE_HL) {
+			arvif->beacon_buf = kmalloc(IEEE80211_MAX_FRAME_LEN,
+						    GFP_KERNEL);
+
+			/* Using a kernel pointer in place of a dma_addr_t
+			 * token can lead to undefined behavior if that
+			 * makes it into cache management functions. Use a
+			 * known-invalid address token instead, which
+			 * avoids the warning and makes it easier to catch
+			 * bugs if it does end up getting used.
+			 */
+			arvif->beacon_paddr = DMA_MAPPING_ERROR;
+		} else {
+			arvif->beacon_buf =
+				dma_alloc_coherent(ar->dev,
+						   IEEE80211_MAX_FRAME_LEN,
+						   &arvif->beacon_paddr,
+						   GFP_ATOMIC);
+		}
 		if (!arvif->beacon_buf) {
 			ret = -ENOMEM;
 			ath10k_warn(ar, "failed to allocate beacon buffer: %d\n",
@@ -5794,8 +5836,12 @@
 
 err:
 	if (arvif->beacon_buf) {
-		dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN,
-				  arvif->beacon_buf, arvif->beacon_paddr);
+		if (ar->bus_param.dev_type == ATH10K_DEV_TYPE_HL)
+			kfree(arvif->beacon_buf);
+		else
+			dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN,
+					  arvif->beacon_buf,
+					  arvif->beacon_paddr);
 		arvif->beacon_buf = NULL;
 	}
 
@@ -7541,10 +7587,7 @@
 				/* Clean up the peer object as well since we
 				 * must have failed to do this above.
 				 */
-				list_del(&peer->list);
-				ar->peer_map[i] = NULL;
-				kfree(peer);
-				ar->num_peers--;
+				ath10k_peer_map_cleanup(ar, peer);
 			}
 		}
 		spin_unlock_bh(&ar->data_lock);
@@ -9023,7 +9066,7 @@
 	{6,  {2633, 2925}, {1215, 1350}, {585,  650} },
 	{7,  {2925, 3250}, {1350, 1500}, {650,  722} },
 	{8,  {3510, 3900}, {1620, 1800}, {780,  867} },
-	{9,  {3900, 4333}, {1800, 2000}, {780,  867} }
+	{9,  {3900, 4333}, {1800, 2000}, {865,  960} }
 };
 
 /*MCS parameters with Nss = 2 */
@@ -9038,7 +9081,7 @@
 	{6,  {5265, 5850}, {2430, 2700}, {1170, 1300} },
 	{7,  {5850, 6500}, {2700, 3000}, {1300, 1444} },
 	{8,  {7020, 7800}, {3240, 3600}, {1560, 1733} },
-	{9,  {7800, 8667}, {3600, 4000}, {1560, 1733} }
+	{9,  {7800, 8667}, {3600, 4000}, {1730, 1920} }
 };
 
 static void ath10k_mac_get_rate_flags_ht(struct ath10k *ar, u32 rate, u8 nss, u8 mcs,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/pci.c
@@ -1963,8 +1963,9 @@
 	ath10k_pci_irq_enable(ar);
 	ath10k_pci_rx_post(ar);
 
-	pcie_capability_write_word(ar_pci->pdev, PCI_EXP_LNKCTL,
-				   ar_pci->link_ctl);
+	pcie_capability_clear_and_set_word(ar_pci->pdev, PCI_EXP_LNKCTL,
+					   PCI_EXP_LNKCTL_ASPMC,
+					   ar_pci->link_ctl & PCI_EXP_LNKCTL_ASPMC);
 
 	return 0;
 }
@@ -2821,8 +2822,8 @@
 
 	pcie_capability_read_word(ar_pci->pdev, PCI_EXP_LNKCTL,
 				  &ar_pci->link_ctl);
-	pcie_capability_write_word(ar_pci->pdev, PCI_EXP_LNKCTL,
-				   ar_pci->link_ctl & ~PCI_EXP_LNKCTL_ASPMC);
+	pcie_capability_clear_word(ar_pci->pdev, PCI_EXP_LNKCTL,
+				   PCI_EXP_LNKCTL_ASPMC);
 
 	/*
 	 * Bring the target up cleanly.
@@ -3793,18 +3794,22 @@
 
 static int __init ath10k_pci_init(void)
 {
-	int ret;
+	int ret1, ret2;
 
-	ret = pci_register_driver(&ath10k_pci_driver);
-	if (ret)
+	ret1 = pci_register_driver(&ath10k_pci_driver);
+	if (ret1)
 		printk(KERN_ERR "failed to register ath10k pci driver: %d\n",
-		       ret);
+		       ret1);
 
-	ret = ath10k_ahb_init();
-	if (ret)
-		printk(KERN_ERR "ahb init failed: %d\n", ret);
+	ret2 = ath10k_ahb_init();
+	if (ret2)
+		printk(KERN_ERR "ahb init failed: %d\n", ret2);
 
-	return ret;
+	if (ret1 && ret2)
+		return ret1;
+
+	/* registered to at least one bus */
+	return 0;
 }
 module_init(ath10k_pci_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/qmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/qmi.c
@@ -864,7 +864,8 @@
 
 	ath10k_qmi_remove_msa_permission(qmi);
 	ath10k_core_free_board_files(ar);
-	if (!test_bit(ATH10K_SNOC_FLAG_UNREGISTERING, &ar_snoc->flags))
+	if (!test_bit(ATH10K_SNOC_FLAG_UNREGISTERING, &ar_snoc->flags) &&
+	    !test_bit(ATH10K_SNOC_FLAG_MODEM_STOPPED, &ar_snoc->flags))
 		ath10k_snoc_fw_crashed_dump(ar);
 
 	ath10k_snoc_fw_indication(ar, ATH10K_QMI_EVENT_FW_DOWN_IND);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/sdio.c
@@ -3,6 +3,7 @@
  * Copyright (c) 2004-2011 Atheros Communications Inc.
  * Copyright (c) 2011-2012,2017 Qualcomm Atheros, Inc.
  * Copyright (c) 2016-2017 Erik Stromdahl <erik.stromdahl@gmail.com>
+ * Copyright (c) 2022-2024 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <linux/module.h>
@@ -1363,8 +1364,11 @@
 		ep->ep_ops.ep_rx_complete(ar, skb);
 	}
 
-	if (test_bit(ATH10K_FLAG_CORE_REGISTERED, &ar->dev_flags))
+	if (test_bit(ATH10K_FLAG_CORE_REGISTERED, &ar->dev_flags)) {
+		local_bh_disable();
 		napi_schedule(&ar->napi);
+		local_bh_enable();
+	}
 }
 
 static int ath10k_sdio_read_rtc_state(struct ath10k_sdio *ar_sdio, unsigned char *state)
@@ -2645,10 +2649,9 @@
 
 	netif_napi_del(&ar->napi);
 
-	ath10k_core_destroy(ar);
-
-	flush_workqueue(ar_sdio->workqueue);
 	destroy_workqueue(ar_sdio->workqueue);
+
+	ath10k_core_destroy(ar);
 }
 
 static const struct sdio_device_id ath10k_sdio_devices[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/snoc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/snoc.c
@@ -12,6 +12,7 @@
 #include <linux/platform_device.h>
 #include <linux/property.h>
 #include <linux/regulator/consumer.h>
+#include <linux/remoteproc/qcom_rproc.h>
 #include <linux/of_address.h>
 #include <linux/iommu.h>
 
@@ -827,12 +828,20 @@
 
 static inline void ath10k_snoc_irq_disable(struct ath10k *ar)
 {
-	ath10k_ce_disable_interrupts(ar);
+	struct ath10k_snoc *ar_snoc = ath10k_snoc_priv(ar);
+	int id;
+
+	for (id = 0; id < CE_COUNT_MAX; id++)
+		disable_irq(ar_snoc->ce_irqs[id].irq_line);
 }
 
 static inline void ath10k_snoc_irq_enable(struct ath10k *ar)
 {
-	ath10k_ce_enable_interrupts(ar);
+	struct ath10k_snoc *ar_snoc = ath10k_snoc_priv(ar);
+	int id;
+
+	for (id = 0; id < CE_COUNT_MAX; id++)
+		enable_irq(ar_snoc->ce_irqs[id].irq_line);
 }
 
 static void ath10k_snoc_rx_pipe_cleanup(struct ath10k_snoc_pipe *snoc_pipe)
@@ -1088,6 +1097,8 @@
 		goto err_free_rri;
 	}
 
+	ath10k_ce_enable_interrupts(ar);
+
 	return 0;
 
 err_free_rri:
@@ -1248,13 +1259,12 @@
 static int ath10k_snoc_request_irq(struct ath10k *ar)
 {
 	struct ath10k_snoc *ar_snoc = ath10k_snoc_priv(ar);
-	int irqflags = IRQF_TRIGGER_RISING;
 	int ret, id;
 
 	for (id = 0; id < CE_COUNT_MAX; id++) {
 		ret = request_irq(ar_snoc->ce_irqs[id].irq_line,
 				  ath10k_snoc_per_engine_handler,
-				  irqflags, ce_name[id], ar);
+				  IRQF_NO_AUTOEN, ce_name[id], ar);
 		if (ret) {
 			ath10k_err(ar,
 				   "failed to register IRQ handler for CE %d: %d\n",
@@ -1477,6 +1487,74 @@
 	mutex_unlock(&ar->dump_mutex);
 }
 
+static int ath10k_snoc_modem_notify(struct notifier_block *nb, unsigned long action,
+				    void *data)
+{
+	struct ath10k_snoc *ar_snoc = container_of(nb, struct ath10k_snoc, nb);
+	struct ath10k *ar = ar_snoc->ar;
+	struct qcom_ssr_notify_data *notify_data = data;
+
+	switch (action) {
+	case QCOM_SSR_BEFORE_POWERUP:
+		ath10k_dbg(ar, ATH10K_DBG_SNOC, "received modem starting event\n");
+		clear_bit(ATH10K_SNOC_FLAG_MODEM_STOPPED, &ar_snoc->flags);
+		break;
+
+	case QCOM_SSR_AFTER_POWERUP:
+		ath10k_dbg(ar, ATH10K_DBG_SNOC, "received modem running event\n");
+		break;
+
+	case QCOM_SSR_BEFORE_SHUTDOWN:
+		ath10k_dbg(ar, ATH10K_DBG_SNOC, "received modem %s event\n",
+			   notify_data->crashed ? "crashed" : "stopping");
+		if (!notify_data->crashed)
+			set_bit(ATH10K_SNOC_FLAG_MODEM_STOPPED, &ar_snoc->flags);
+		else
+			clear_bit(ATH10K_SNOC_FLAG_MODEM_STOPPED, &ar_snoc->flags);
+		break;
+
+	case QCOM_SSR_AFTER_SHUTDOWN:
+		ath10k_dbg(ar, ATH10K_DBG_SNOC, "received modem offline event\n");
+		break;
+
+	default:
+		ath10k_err(ar, "received unrecognized event %lu\n", action);
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+static int ath10k_modem_init(struct ath10k *ar)
+{
+	struct ath10k_snoc *ar_snoc = ath10k_snoc_priv(ar);
+	void *notifier;
+	int ret;
+
+	ar_snoc->nb.notifier_call = ath10k_snoc_modem_notify;
+
+	notifier = qcom_register_ssr_notifier("mpss", &ar_snoc->nb);
+	if (IS_ERR(notifier)) {
+		ret = PTR_ERR(notifier);
+		ath10k_err(ar, "failed to initialize modem notifier: %d\n", ret);
+		return ret;
+	}
+
+	ar_snoc->notifier = notifier;
+
+	return 0;
+}
+
+static void ath10k_modem_deinit(struct ath10k *ar)
+{
+	int ret;
+	struct ath10k_snoc *ar_snoc = ath10k_snoc_priv(ar);
+
+	ret = qcom_unregister_ssr_notifier(ar_snoc->notifier, &ar_snoc->nb);
+	if (ret)
+		ath10k_err(ar, "error %d unregistering notifier\n", ret);
+}
+
 static int ath10k_setup_msa_resources(struct ath10k *ar, u32 msa_size)
 {
 	struct device *dev = ar->dev;
@@ -1487,11 +1565,11 @@
 	node = of_parse_phandle(dev->of_node, "memory-region", 0);
 	if (node) {
 		ret = of_address_to_resource(node, 0, &r);
+		of_node_put(node);
 		if (ret) {
 			dev_err(dev, "failed to resolve msa fixed region\n");
 			return ret;
 		}
-		of_node_put(node);
 
 		ar->msa.paddr = r.start;
 		ar->msa.mem_size = resource_size(&r);
@@ -1740,10 +1818,17 @@
 		goto err_fw_deinit;
 	}
 
+	ret = ath10k_modem_init(ar);
+	if (ret)
+		goto err_qmi_deinit;
+
 	ath10k_dbg(ar, ATH10K_DBG_SNOC, "snoc probe\n");
 
 	return 0;
 
+err_qmi_deinit:
+	ath10k_qmi_deinit(ar);
+
 err_fw_deinit:
 	ath10k_fw_deinit(ar);
 
@@ -1771,6 +1856,7 @@
 	ath10k_fw_deinit(ar);
 	ath10k_snoc_free_irq(ar);
 	ath10k_snoc_release_resource(ar);
+	ath10k_modem_deinit(ar);
 	ath10k_qmi_deinit(ar);
 	ath10k_core_destroy(ar);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/snoc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/snoc.h
@@ -6,6 +6,8 @@
 #ifndef _SNOC_H_
 #define _SNOC_H_
 
+#include <linux/notifier.h>
+
 #include "hw.h"
 #include "ce.h"
 #include "qmi.h"
@@ -45,6 +47,7 @@
 enum ath10k_snoc_flags {
 	ATH10K_SNOC_FLAG_REGISTERED,
 	ATH10K_SNOC_FLAG_UNREGISTERING,
+	ATH10K_SNOC_FLAG_MODEM_STOPPED,
 	ATH10K_SNOC_FLAG_RECOVERY,
 	ATH10K_SNOC_FLAG_8BIT_HOST_CAP_QUIRK,
 };
@@ -75,6 +78,8 @@
 	struct clk_bulk_data *clks;
 	size_t num_clks;
 	struct ath10k_qmi *qmi;
+	struct notifier_block nb;
+	void *notifier;
 	unsigned long flags;
 	bool xo_cal_supported;
 	u32 xo_cal_data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/targaddrs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/targaddrs.h
@@ -491,4 +491,7 @@
 #define QCA4019_BOARD_DATA_SZ	  12064
 #define QCA4019_BOARD_EXT_DATA_SZ 0
 
+#define WCN3990_BOARD_DATA_SZ	  26328
+#define WCN3990_BOARD_EXT_DATA_SZ 0
+
 #endif /* __TARGADDRS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/txrx.c
@@ -82,8 +82,6 @@
 	flags = skb_cb->flags;
 	ath10k_htt_tx_free_msdu_id(htt, tx_done->msdu_id);
 	ath10k_htt_tx_dec_pending(htt);
-	if (htt->num_pending_tx == 0)
-		wake_up(&htt->empty_tx_wq);
 	spin_unlock_bh(&htt->tx_lock);
 
 	rcu_read_lock();
@@ -127,7 +125,7 @@
 	    tx_done->ack_rssi != ATH10K_INVALID_RSSI) {
 		info->status.ack_signal = ATH10K_DEFAULT_NOISE_FLOOR +
 						tx_done->ack_rssi;
-		info->status.is_valid_ack_signal = true;
+		info->status.flags |= IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
 	}
 
 	ieee80211_tx_status(htt->ar->hw, msdu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/usb.c
@@ -525,7 +525,7 @@
 			      req,
 			      USB_DIR_IN | USB_TYPE_VENDOR |
 			      USB_RECIP_DEVICE, value, index, buf,
-			      size, 2 * HZ);
+			      size, 2000);
 
 	if (ret < 0) {
 		ath10k_warn(ar, "Failed to read usb control message: %d\n",
@@ -853,6 +853,11 @@
 				   le16_to_cpu(endpoint->wMaxPacketSize),
 				   endpoint->bInterval);
 		}
+
+		/* Ignore broken descriptors. */
+		if (usb_endpoint_maxp(endpoint) == 0)
+			continue;
+
 		urbcount = 0;
 
 		pipe_num =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -844,6 +844,10 @@
 	}
 
 	ev = tb[WMI_TLV_TAG_STRUCT_MGMT_TX_COMPL_EVENT];
+	if (!ev) {
+		kfree(tb);
+		return -EPROTO;
+	}
 
 	arg->desc_id = ev->desc_id;
 	arg->status = ev->status;
@@ -3031,9 +3035,14 @@
 				       struct sk_buff *msdu)
 {
 	struct ath10k_skb_cb *cb = ATH10K_SKB_CB(msdu);
+	struct ath10k_mgmt_tx_pkt_addr *pkt_addr;
 	struct ath10k_wmi *wmi = &ar->wmi;
 
-	idr_remove(&wmi->mgmt_pending_tx, cb->msdu_id);
+	spin_lock_bh(&ar->data_lock);
+	pkt_addr = idr_remove(&wmi->mgmt_pending_tx, cb->msdu_id);
+	spin_unlock_bh(&ar->data_lock);
+
+	kfree(pkt_addr);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/wmi.c
@@ -1762,12 +1762,32 @@
 
 int ath10k_wmi_wait_for_service_ready(struct ath10k *ar)
 {
-	unsigned long time_left;
+	unsigned long time_left, i;
 
 	time_left = wait_for_completion_timeout(&ar->wmi.service_ready,
 						WMI_SERVICE_READY_TIMEOUT_HZ);
-	if (!time_left)
-		return -ETIMEDOUT;
+	if (!time_left) {
+		/* Sometimes the PCI HIF doesn't receive interrupt
+		 * for the service ready message even if the buffer
+		 * was completed. PCIe sniffer shows that it's
+		 * because the corresponding CE ring doesn't fires
+		 * it. Workaround here by polling CE rings once.
+		 */
+		ath10k_warn(ar, "failed to receive service ready completion, polling..\n");
+
+		for (i = 0; i < CE_COUNT; i++)
+			ath10k_hif_send_complete_check(ar, i, 1);
+
+		time_left = wait_for_completion_timeout(&ar->wmi.service_ready,
+							WMI_SERVICE_READY_TIMEOUT_HZ);
+		if (!time_left) {
+			ath10k_warn(ar, "polling timed out\n");
+			return -ETIMEDOUT;
+		}
+
+		ath10k_warn(ar, "service ready completion received, continuing normally\n");
+	}
+
 	return 0;
 }
 
@@ -2420,6 +2440,7 @@
 	dma_unmap_single(ar->dev, pkt_addr->paddr,
 			 msdu->len, DMA_TO_DEVICE);
 	info = IEEE80211_SKB_CB(msdu);
+	kfree(pkt_addr);
 
 	if (param->status) {
 		info->flags &= ~IEEE80211_TX_STAT_ACK;
@@ -2427,7 +2448,7 @@
 		info->flags |= IEEE80211_TX_STAT_ACK;
 		info->status.ack_signal = ATH10K_DEFAULT_NOISE_FLOOR +
 					  param->ack_rssi;
-		info->status.is_valid_ack_signal = true;
+		info->status.flags |= IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
 	}
 
 	ieee80211_tx_status_irqsafe(ar->hw, msdu);
@@ -2610,6 +2631,10 @@
 	if (ieee80211_is_beacon(hdr->frame_control))
 		ath10k_mac_handle_beacon(ar, skb);
 
+	if (ieee80211_is_beacon(hdr->frame_control) ||
+	    ieee80211_is_probe_resp(hdr->frame_control))
+		status->boottime_ns = ktime_get_boottime_ns();
+
 	ath10k_dbg(ar, ATH10K_DBG_MGMT,
 		   "event mgmt rx skb %pK len %d ftype %02x stype %02x\n",
 		   skb, skb->len,
@@ -9557,6 +9582,7 @@
 	dma_unmap_single(ar->dev, pkt_addr->paddr,
 			 msdu->len, DMA_TO_DEVICE);
 	ieee80211_free_txskb(ar->hw, msdu);
+	kfree(pkt_addr);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/wmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/wmi.h
@@ -2066,7 +2066,9 @@
 	union {
 		__le32 reginfo1;
 		struct {
+			/* note: power unit is 1 dBm */
 			u8 antenna_max;
+			/* note: power unit is 0.5 dBm */
 			u8 max_tx_power;
 		} __packed;
 	} __packed;
@@ -2086,6 +2088,7 @@
 	u32 min_power;
 	u32 max_power;
 	u32 max_reg_power;
+	/* note: power unit is 1 dBm */
 	u32 max_antenna_gain;
 	u32 reg_class_id;
 	enum wmi_phy_mode mode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath10k/wow.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath10k/wow.c
@@ -337,14 +337,15 @@
 			if (patterns[i].mask[j / 8] & BIT(j % 8))
 				bitmask[j] = 0xff;
 		old_pattern.mask = bitmask;
-		new_pattern = old_pattern;
 
 		if (ar->wmi.rx_decap_mode == ATH10K_HW_TXRX_NATIVE_WIFI) {
-			if (patterns[i].pkt_offset < ETH_HLEN)
+			if (patterns[i].pkt_offset < ETH_HLEN) {
 				ath10k_wow_convert_8023_to_80211(&new_pattern,
 								 &old_pattern);
-			else
+			} else {
+				new_pattern = old_pattern;
 				new_pattern.pkt_offset += WOW_HDR_LEN - ETH_HLEN;
+			}
 		}
 
 		if (WARN_ON(new_pattern.pattern_len > WOW_MAX_PATTERN_SIZE))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/ahb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/ahb.c
@@ -175,8 +175,11 @@
 
 		ath11k_ahb_ext_grp_disable(irq_grp);
 
-		napi_synchronize(&irq_grp->napi);
-		napi_disable(&irq_grp->napi);
+		if (irq_grp->napi_enabled) {
+			napi_synchronize(&irq_grp->napi);
+			napi_disable(&irq_grp->napi);
+			irq_grp->napi_enabled = false;
+		}
 	}
 }
 
@@ -206,13 +209,13 @@
 
 static void ath11k_ahb_ce_irq_enable(struct ath11k_base *ab, u16 ce_id)
 {
-	const struct ce_pipe_config *ce_config;
+	const struct ce_attr *ce_attr;
 
-	ce_config = &ab->hw_params.target_ce_config[ce_id];
-	if (__le32_to_cpu(ce_config->pipedir) & PIPEDIR_OUT)
+	ce_attr = &ab->hw_params.host_ce_config[ce_id];
+	if (ce_attr->src_nentries)
 		ath11k_ahb_setbit32(ab, ce_id, CE_HOST_IE_ADDRESS);
 
-	if (__le32_to_cpu(ce_config->pipedir) & PIPEDIR_IN) {
+	if (ce_attr->dest_nentries) {
 		ath11k_ahb_setbit32(ab, ce_id, CE_HOST_IE_2_ADDRESS);
 		ath11k_ahb_setbit32(ab, ce_id + CE_HOST_IE_3_SHIFT,
 				    CE_HOST_IE_3_ADDRESS);
@@ -221,13 +224,13 @@
 
 static void ath11k_ahb_ce_irq_disable(struct ath11k_base *ab, u16 ce_id)
 {
-	const struct ce_pipe_config *ce_config;
+	const struct ce_attr *ce_attr;
 
-	ce_config = &ab->hw_params.target_ce_config[ce_id];
-	if (__le32_to_cpu(ce_config->pipedir) & PIPEDIR_OUT)
+	ce_attr = &ab->hw_params.host_ce_config[ce_id];
+	if (ce_attr->src_nentries)
 		ath11k_ahb_clearbit32(ab, ce_id, CE_HOST_IE_ADDRESS);
 
-	if (__le32_to_cpu(ce_config->pipedir) & PIPEDIR_IN) {
+	if (ce_attr->dest_nentries) {
 		ath11k_ahb_clearbit32(ab, ce_id, CE_HOST_IE_2_ADDRESS);
 		ath11k_ahb_clearbit32(ab, ce_id + CE_HOST_IE_3_SHIFT,
 				      CE_HOST_IE_3_ADDRESS);
@@ -300,7 +303,10 @@
 	for (i = 0; i < ATH11K_EXT_IRQ_GRP_NUM_MAX; i++) {
 		struct ath11k_ext_irq_grp *irq_grp = &ab->ext_irq_grp[i];
 
-		napi_enable(&irq_grp->napi);
+		if (!irq_grp->napi_enabled) {
+			napi_enable(&irq_grp->napi);
+			irq_grp->napi_enabled = true;
+		}
 		ath11k_ahb_ext_grp_enable(irq_grp);
 	}
 }
@@ -385,6 +391,8 @@
 
 		for (j = 0; j < irq_grp->num_irq; j++)
 			free_irq(ab->irq_num[irq_grp->irqs[j]], irq_grp);
+
+		netif_napi_del(&irq_grp->napi);
 	}
 }
 
@@ -642,8 +650,8 @@
 
 	prproc = rproc_get_by_phandle(rproc_phandle);
 	if (!prproc) {
-		ath11k_err(ab, "failed to get rproc\n");
-		return -EINVAL;
+		ath11k_dbg(ab, ATH11K_DBG_AHB, "failed to get rproc, deferring\n");
+		return -EPROBE_DEFER;
 	}
 	ab_ahb->tgt_rproc = prproc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/core.c
@@ -71,6 +71,7 @@
 		.supports_suspend = false,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
 		.fix_l1ss = true,
+		.wakeup_mhi = false,
 	},
 	{
 		.hw_rev = ATH11K_HW_IPQ6018_HW10,
@@ -112,6 +113,7 @@
 		.supports_suspend = false,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
 		.fix_l1ss = true,
+		.wakeup_mhi = false,
 	},
 	{
 		.name = "qca6390 hw2.0",
@@ -152,6 +154,7 @@
 		.supports_suspend = true,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
 		.fix_l1ss = true,
+		.wakeup_mhi = true,
 	},
 	{
 		.name = "qcn9074 hw1.0",
@@ -190,6 +193,7 @@
 		.supports_suspend = false,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_qcn9074),
 		.fix_l1ss = true,
+		.wakeup_mhi = false,
 	},
 	{
 		.name = "wcn6855 hw2.0",
@@ -230,6 +234,7 @@
 		.supports_suspend = true,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_wcn6855),
 		.fix_l1ss = false,
+		.wakeup_mhi = true,
 	},
 };
 
@@ -347,11 +352,26 @@
 		scnprintf(variant, sizeof(variant), ",variant=%s",
 			  ab->qmi.target.bdf_ext);
 
-	scnprintf(name, name_len,
-		  "bus=%s,qmi-chip-id=%d,qmi-board-id=%d%s",
-		  ath11k_bus_str(ab->hif.bus),
-		  ab->qmi.target.chip_id,
-		  ab->qmi.target.board_id, variant);
+	switch (ab->id.bdf_search) {
+	case ATH11K_BDF_SEARCH_BUS_AND_BOARD:
+		scnprintf(name, name_len,
+			  "bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x,qmi-chip-id=%d,qmi-board-id=%d%s",
+			  ath11k_bus_str(ab->hif.bus),
+			  ab->id.vendor, ab->id.device,
+			  ab->id.subsystem_vendor,
+			  ab->id.subsystem_device,
+			  ab->qmi.target.chip_id,
+			  ab->qmi.target.board_id,
+			  variant);
+		break;
+	default:
+		scnprintf(name, name_len,
+			  "bus=%s,qmi-chip-id=%d,qmi-board-id=%d%s",
+			  ath11k_bus_str(ab->hif.bus),
+			  ab->qmi.target.chip_id,
+			  ab->qmi.target.board_id, variant);
+		break;
+	}
 
 	ath11k_dbg(ab, ATH11K_DBG_BOOT, "boot using board name '%s'\n", name);
 
@@ -588,7 +608,7 @@
 	return 0;
 }
 
-#define BOARD_NAME_SIZE 100
+#define BOARD_NAME_SIZE 200
 int ath11k_core_fetch_bdf(struct ath11k_base *ab, struct ath11k_board_data *bd)
 {
 	char boardname[BOARD_NAME_SIZE];
@@ -679,23 +699,23 @@
 		return ret;
 	}
 
-	ret = ath11k_mac_register(ab);
+	ret = ath11k_dp_pdev_alloc(ab);
 	if (ret) {
-		ath11k_err(ab, "failed register the radio with mac80211: %d\n", ret);
+		ath11k_err(ab, "failed to attach DP pdev: %d\n", ret);
 		goto err_pdev_debug;
 	}
 
-	ret = ath11k_dp_pdev_alloc(ab);
+	ret = ath11k_mac_register(ab);
 	if (ret) {
-		ath11k_err(ab, "failed to attach DP pdev: %d\n", ret);
-		goto err_mac_unregister;
+		ath11k_err(ab, "failed register the radio with mac80211: %d\n", ret);
+		goto err_dp_pdev_free;
 	}
 
 	ret = ath11k_thermal_register(ab);
 	if (ret) {
 		ath11k_err(ab, "could not register thermal device: %d\n",
 			   ret);
-		goto err_dp_pdev_free;
+		goto err_mac_unregister;
 	}
 
 	ret = ath11k_spectral_init(ab);
@@ -708,10 +728,10 @@
 
 err_thermal_unregister:
 	ath11k_thermal_unregister(ab);
-err_dp_pdev_free:
-	ath11k_dp_pdev_free(ab);
 err_mac_unregister:
 	ath11k_mac_unregister(ab);
+err_dp_pdev_free:
+	ath11k_dp_pdev_free(ab);
 err_pdev_debug:
 	ath11k_debugfs_pdev_destroy(ab);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/core.h
@@ -47,6 +47,11 @@
 	ATH11K_BW_160	= 3,
 };
 
+enum ath11k_bdf_search {
+	ATH11K_BDF_SEARCH_DEFAULT,
+	ATH11K_BDF_SEARCH_BUS_AND_BOARD,
+};
+
 enum wme_ac {
 	WME_AC_BE,
 	WME_AC_BK,
@@ -132,6 +137,7 @@
 	u32 num_irq;
 	u32 grp_id;
 	u64 timestamp;
+	bool napi_enabled;
 	struct napi_struct napi;
 	struct net_device napi_ndev;
 };
@@ -701,7 +707,6 @@
 	u32 wlan_init_status;
 	int irq_num[ATH11K_IRQ_NUM_MAX];
 	struct ath11k_ext_irq_grp ext_irq_grp[ATH11K_EXT_IRQ_GRP_NUM_MAX];
-	struct napi_struct *napi;
 	struct ath11k_targ_cap target_caps;
 	u32 ext_service_bitmap[WMI_SERVICE_EXT_BM_SIZE];
 	bool pdevs_macaddr_valid;
@@ -726,7 +731,6 @@
 	enum ath11k_dfs_region dfs_region;
 #ifdef CONFIG_ATH11K_DEBUGFS
 	struct dentry *debugfs_soc;
-	struct dentry *debugfs_ath11k;
 #endif
 	struct ath11k_soc_dp_stats soc_stats;
 
@@ -747,6 +751,14 @@
 
 	struct completion htc_suspend;
 
+	struct {
+		enum ath11k_bdf_search bdf_search;
+		u32 vendor;
+		u32 device;
+		u32 subsystem_vendor;
+		u32 subsystem_device;
+	} id;
+
 	/* must be last */
 	u8 drv_priv[0] __aligned(sizeof(void *));
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/dbring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/dbring.c
@@ -8,8 +8,7 @@
 
 static int ath11k_dbring_bufs_replenish(struct ath11k *ar,
 					struct ath11k_dbring *ring,
-					struct ath11k_dbring_element *buff,
-					gfp_t gfp)
+					struct ath11k_dbring_element *buff)
 {
 	struct ath11k_base *ab = ar->ab;
 	struct hal_srng *srng;
@@ -35,7 +34,7 @@
 		goto err;
 
 	spin_lock_bh(&ring->idr_lock);
-	buf_id = idr_alloc(&ring->bufs_idr, buff, 0, ring->bufs_max, gfp);
+	buf_id = idr_alloc(&ring->bufs_idr, buff, 0, ring->bufs_max, GFP_ATOMIC);
 	spin_unlock_bh(&ring->idr_lock);
 	if (buf_id < 0) {
 		ret = -ENOBUFS;
@@ -72,8 +71,7 @@
 }
 
 static int ath11k_dbring_fill_bufs(struct ath11k *ar,
-				   struct ath11k_dbring *ring,
-				   gfp_t gfp)
+				   struct ath11k_dbring *ring)
 {
 	struct ath11k_dbring_element *buff;
 	struct hal_srng *srng;
@@ -92,11 +90,11 @@
 	size = sizeof(*buff) + ring->buf_sz + align - 1;
 
 	while (num_remain > 0) {
-		buff = kzalloc(size, gfp);
+		buff = kzalloc(size, GFP_ATOMIC);
 		if (!buff)
 			break;
 
-		ret = ath11k_dbring_bufs_replenish(ar, ring, buff, gfp);
+		ret = ath11k_dbring_bufs_replenish(ar, ring, buff);
 		if (ret) {
 			ath11k_warn(ar->ab, "failed to replenish db ring num_remain %d req_ent %d\n",
 				    num_remain, req_entries);
@@ -176,7 +174,7 @@
 	ring->hp_addr = ath11k_hal_srng_get_hp_addr(ar->ab, srng);
 	ring->tp_addr = ath11k_hal_srng_get_tp_addr(ar->ab, srng);
 
-	ret = ath11k_dbring_fill_bufs(ar, ring, GFP_KERNEL);
+	ret = ath11k_dbring_fill_bufs(ar, ring);
 
 	return ret;
 }
@@ -322,7 +320,7 @@
 		}
 
 		memset(buff, 0, size);
-		ath11k_dbring_bufs_replenish(ar, ring, buff, GFP_ATOMIC);
+		ath11k_dbring_bufs_replenish(ar, ring, buff);
 	}
 
 	spin_unlock_bh(&srng->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/debug.h
@@ -23,8 +23,8 @@
 	ATH11K_DBG_TESTMODE	= 0x00000400,
 	ATH11k_DBG_HAL		= 0x00000800,
 	ATH11K_DBG_PCI		= 0x00001000,
-	ATH11K_DBG_DP_TX	= 0x00001000,
-	ATH11K_DBG_DP_RX	= 0x00002000,
+	ATH11K_DBG_DP_TX	= 0x00002000,
+	ATH11K_DBG_DP_RX	= 0x00004000,
 	ATH11K_DBG_ANY		= 0xffffffff,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/debugfs.c
@@ -836,10 +836,6 @@
 	if (test_bit(ATH11K_FLAG_REGISTERED, &ab->dev_flags))
 		return 0;
 
-	ab->debugfs_soc = debugfs_create_dir(ab->hw_params.name, ab->debugfs_ath11k);
-	if (IS_ERR(ab->debugfs_soc))
-		return PTR_ERR(ab->debugfs_soc);
-
 	debugfs_create_file("simulate_fw_crash", 0600, ab->debugfs_soc, ab,
 			    &fops_simulate_fw_crash);
 
@@ -857,15 +853,51 @@
 
 int ath11k_debugfs_soc_create(struct ath11k_base *ab)
 {
-	ab->debugfs_ath11k = debugfs_create_dir("ath11k", NULL);
+	struct dentry *root;
+	bool dput_needed;
+	char name[64];
+	int ret;
+
+	root = debugfs_lookup("ath11k", NULL);
+	if (!root) {
+		root = debugfs_create_dir("ath11k", NULL);
+		if (IS_ERR_OR_NULL(root))
+			return PTR_ERR(root);
+
+		dput_needed = false;
+	} else {
+		/* a dentry from lookup() needs dput() after we don't use it */
+		dput_needed = true;
+	}
+
+	scnprintf(name, sizeof(name), "%s-%s", ath11k_bus_str(ab->hif.bus),
+		  dev_name(ab->dev));
+
+	ab->debugfs_soc = debugfs_create_dir(name, root);
+	if (IS_ERR_OR_NULL(ab->debugfs_soc)) {
+		ret = PTR_ERR(ab->debugfs_soc);
+		goto out;
+	}
+
+	ret = 0;
+
+out:
+	if (dput_needed)
+		dput(root);
 
-	return PTR_ERR_OR_ZERO(ab->debugfs_ath11k);
+	return ret;
 }
 
 void ath11k_debugfs_soc_destroy(struct ath11k_base *ab)
 {
-	debugfs_remove_recursive(ab->debugfs_ath11k);
-	ab->debugfs_ath11k = NULL;
+	debugfs_remove_recursive(ab->debugfs_soc);
+	ab->debugfs_soc = NULL;
+
+	/* We are not removing ath11k directory on purpose, even if it
+	 * would be empty. This simplifies the directory handling and it's
+	 * a minor cosmetic issue to leave an empty ath11k directory to
+	 * debugfs.
+	 */
 }
 EXPORT_SYMBOL(ath11k_debugfs_soc_destroy);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/dp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/dp.h
@@ -515,7 +515,8 @@
 } __packed;
 
 #define HTT_PPDU_STATS_CFG_MSG_TYPE		GENMASK(7, 0)
-#define HTT_PPDU_STATS_CFG_PDEV_ID		GENMASK(15, 8)
+#define HTT_PPDU_STATS_CFG_SOC_STATS		BIT(8)
+#define HTT_PPDU_STATS_CFG_PDEV_ID		GENMASK(15, 9)
 #define HTT_PPDU_STATS_CFG_TLV_TYPE_BITMASK	GENMASK(31, 16)
 
 enum htt_ppdu_stats_tag_type {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/dp_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/dp_rx.c
@@ -354,10 +354,10 @@
 			goto fail_free_skb;
 
 		spin_lock_bh(&rx_ring->idr_lock);
-		buf_id = idr_alloc(&rx_ring->bufs_idr, skb, 0,
-				   rx_ring->bufs_max * 3, GFP_ATOMIC);
+		buf_id = idr_alloc(&rx_ring->bufs_idr, skb, 1,
+				   (rx_ring->bufs_max * 3) + 1, GFP_ATOMIC);
 		spin_unlock_bh(&rx_ring->idr_lock);
-		if (buf_id < 0)
+		if (buf_id <= 0)
 			goto fail_dma_unmap;
 
 		desc = ath11k_hal_srng_src_get_next_entry(ab, srng);
@@ -1603,14 +1603,20 @@
 	u8 pdev_id;
 
 	pdev_id = FIELD_GET(HTT_T2H_PPDU_STATS_INFO_PDEV_ID, data->hdr);
+
+	rcu_read_lock();
+
 	ar = ath11k_mac_get_ar_by_pdev_id(ab, pdev_id);
 	if (!ar) {
 		ath11k_warn(ab, "invalid pdev id %d on htt pktlog\n", pdev_id);
-		return;
+		goto out;
 	}
 
 	trace_ath11k_htt_pktlog(ar, data->payload, hdr->size,
 				ar->ab->pktlog_defs_checksum);
+
+out:
+	rcu_read_unlock();
 }
 
 static void ath11k_htt_backpressure_event_handler(struct ath11k_base *ab,
@@ -1855,8 +1861,7 @@
 			  CHECKSUM_NONE : CHECKSUM_UNNECESSARY;
 }
 
-static int ath11k_dp_rx_crypto_mic_len(struct ath11k *ar,
-				       enum hal_encrypt_type enctype)
+int ath11k_dp_rx_crypto_mic_len(struct ath11k *ar, enum hal_encrypt_type enctype)
 {
 	switch (enctype) {
 	case HAL_ENCRYPT_TYPE_OPEN:
@@ -2337,8 +2342,10 @@
 	channel_num = meta_data;
 	center_freq = meta_data >> 16;
 
-	if (center_freq >= 5935 && center_freq <= 7105) {
+	if (center_freq >= ATH11K_MIN_6G_FREQ &&
+	    center_freq <= ATH11K_MAX_6G_FREQ) {
 		rx_status->band = NL80211_BAND_6GHZ;
+		rx_status->freq = center_freq;
 	} else if (channel_num >= 1 && channel_num <= 14) {
 		rx_status->band = NL80211_BAND_2GHZ;
 	} else if (channel_num >= 36 && channel_num <= 173) {
@@ -2356,8 +2363,9 @@
 				rx_desc, sizeof(struct hal_rx_desc));
 	}
 
-	rx_status->freq = ieee80211_channel_to_frequency(channel_num,
-							 rx_status->band);
+	if (rx_status->band != NL80211_BAND_6GHZ)
+		rx_status->freq = ieee80211_channel_to_frequency(channel_num,
+								 rx_status->band);
 
 	ath11k_dp_rx_h_rate(ar, rx_desc, rx_status);
 }
@@ -2599,6 +2607,9 @@
 				   cookie);
 		mac_id = FIELD_GET(DP_RXDMA_BUF_COOKIE_PDEV_ID, cookie);
 
+		if (unlikely(buf_id == 0))
+			continue;
+
 		ar = ab->pdevs[mac_id].ar;
 		rx_ring = &ar->dp.rx_refill_buf_ring;
 		spin_lock_bh(&rx_ring->idr_lock);
@@ -2626,7 +2637,7 @@
 		if (push_reason !=
 		    HAL_REO_DEST_RING_PUSH_REASON_ROUTING_INSTRUCTION) {
 			dev_kfree_skb_any(msdu);
-			ab->soc_stats.hal_reo_error[dp->reo_dst_ring[ring_id].ring_id]++;
+			ab->soc_stats.hal_reo_error[ring_id]++;
 			continue;
 		}
 
@@ -3053,6 +3064,7 @@
 	if (!peer) {
 		ath11k_warn(ab, "failed to find the peer to set up fragment info\n");
 		spin_unlock_bh(&ab->base_lock);
+		crypto_free_shash(tfm);
 		return -ENOENT;
 	}
 
@@ -3310,7 +3322,7 @@
 
 	paddr = dma_map_single(ab->dev, defrag_skb->data,
 			       defrag_skb->len + skb_tailroom(defrag_skb),
-			       DMA_FROM_DEVICE);
+			       DMA_TO_DEVICE);
 	if (dma_mapping_error(ab->dev, paddr))
 		return -ENOMEM;
 
@@ -3375,7 +3387,7 @@
 	spin_unlock_bh(&rx_refill_ring->idr_lock);
 err_unmap_dma:
 	dma_unmap_single(ab->dev, paddr, defrag_skb->len + skb_tailroom(defrag_skb),
-			 DMA_FROM_DEVICE);
+			 DMA_TO_DEVICE);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/dp_rx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/dp_rx.h
@@ -1,6 +1,7 @@
 /* SPDX-License-Identifier: BSD-3-Clause-Clear */
 /*
  * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 #ifndef ATH11K_DP_RX_H
 #define ATH11K_DP_RX_H
@@ -95,4 +96,6 @@
 int ath11k_dp_rx_pktlog_start(struct ath11k_base *ab);
 int ath11k_dp_rx_pktlog_stop(struct ath11k_base *ab, bool stop_timer);
 
+int ath11k_dp_rx_crypto_mic_len(struct ath11k *ar, enum hal_encrypt_type enctype);
+
 #endif /* ATH11K_DP_RX_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/dp_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/dp_tx.c
@@ -349,7 +349,8 @@
 			info->flags |= IEEE80211_TX_STAT_ACK;
 			info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
 						  ts->ack_rssi;
-			info->status.is_valid_ack_signal = true;
+			info->status.flags |=
+				IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
 		} else {
 			info->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
 		}
@@ -453,7 +454,7 @@
 		info->flags |= IEEE80211_TX_STAT_ACK;
 		info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
 					  ts->ack_rssi;
-		info->status.is_valid_ack_signal = true;
+		info->status.flags |= IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
 	}
 
 	if (ts->status == HAL_WBM_TQM_REL_REASON_CMD_REMOVE_TX &&
@@ -895,7 +896,7 @@
 		cmd->msg = FIELD_PREP(HTT_PPDU_STATS_CFG_MSG_TYPE,
 				      HTT_H2T_MSG_TYPE_PPDU_STATS_CFG);
 
-		pdev_mask = 1 << (i + 1);
+		pdev_mask = 1 << (ar->pdev_idx + i);
 		cmd->msg |= FIELD_PREP(HTT_PPDU_STATS_CFG_PDEV_ID, pdev_mask);
 		cmd->msg |= FIELD_PREP(HTT_PPDU_STATS_CFG_TLV_TYPE_BITMASK, mask);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/hal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/hal.c
@@ -947,6 +947,7 @@
 	srng->msi_data = params->msi_data;
 	srng->initialized = 1;
 	spin_lock_init(&srng->lock);
+	lockdep_set_class(&srng->lock, hal->srng_key + ring_id);
 
 	for (i = 0; i < HAL_SRNG_NUM_REG_GRP; i++) {
 		srng->hwreg_base[i] = srng_config->reg_start[i] +
@@ -1233,6 +1234,24 @@
 	return 0;
 }
 
+static void ath11k_hal_register_srng_key(struct ath11k_base *ab)
+{
+	struct ath11k_hal *hal = &ab->hal;
+	u32 ring_id;
+
+	for (ring_id = 0; ring_id < HAL_SRNG_RING_ID_MAX; ring_id++)
+		lockdep_register_key(hal->srng_key + ring_id);
+}
+
+static void ath11k_hal_unregister_srng_key(struct ath11k_base *ab)
+{
+	struct ath11k_hal *hal = &ab->hal;
+	u32 ring_id;
+
+	for (ring_id = 0; ring_id < HAL_SRNG_RING_ID_MAX; ring_id++)
+		lockdep_unregister_key(hal->srng_key + ring_id);
+}
+
 int ath11k_hal_srng_init(struct ath11k_base *ab)
 {
 	struct ath11k_hal *hal = &ab->hal;
@@ -1252,6 +1271,8 @@
 	if (ret)
 		goto err_free_cont_rdp;
 
+	ath11k_hal_register_srng_key(ab);
+
 	return 0;
 
 err_free_cont_rdp:
@@ -1266,6 +1287,7 @@
 {
 	struct ath11k_hal *hal = &ab->hal;
 
+	ath11k_hal_unregister_srng_key(ab);
 	ath11k_hal_free_cont_rdp(ab);
 	ath11k_hal_free_cont_wrp(ab);
 	kfree(hal->srng_config);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/hal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/hal.h
@@ -901,6 +901,8 @@
 	/* shadow register configuration */
 	u32 shadow_reg_addr[HAL_SHADOW_NUM_REGS];
 	int num_shadow_reg_configured;
+
+	struct lock_class_key srng_key[HAL_SRNG_RING_ID_MAX];
 };
 
 u32 ath11k_hal_reo_qdesc_size(u32 ba_window_size, u8 tid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/hw.c
@@ -1015,8 +1015,6 @@
 const struct ath11k_hw_ring_mask ath11k_hw_ring_mask_qca6390 = {
 	.tx  = {
 		ATH11K_TX_RING_MASK_0,
-		ATH11K_TX_RING_MASK_1,
-		ATH11K_TX_RING_MASK_2,
 	},
 	.rx_mon_status = {
 		0, 0, 0, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/hw.h
@@ -163,6 +163,7 @@
 	bool supports_suspend;
 	u32 hal_desc_sz;
 	bool fix_l1ss;
+	bool wakeup_mhi;
 };
 
 struct ath11k_hw_ops {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/mac.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: BSD-3-Clause-Clear
 /*
  * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <net/mac80211.h>
@@ -767,11 +768,15 @@
 
 	if (cfg80211_find_ie(WLAN_EID_RSN, ies, (skb_tail_pointer(bcn) - ies)))
 		arvif->rsnie_present = true;
+	else
+		arvif->rsnie_present = false;
 
 	if (cfg80211_find_vendor_ie(WLAN_OUI_MICROSOFT,
 				    WLAN_OUI_TYPE_MICROSOFT_WPA,
 				    ies, (skb_tail_pointer(bcn) - ies)))
 		arvif->wpaie_present = true;
+	else
+		arvif->wpaie_present = false;
 
 	ret = ath11k_wmi_bcn_tmpl(ar, arvif->vdev_id, &offs, bcn);
 
@@ -2151,6 +2156,19 @@
 		if (ret)
 			ath11k_warn(ar->ab, "failed to update bcn template: %d\n",
 				    ret);
+		if (vif->bss_conf.he_support) {
+			ret = ath11k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+							    WMI_VDEV_PARAM_BA_MODE,
+							    WMI_BA_MODE_BUFFER_SIZE_256);
+			if (ret)
+				ath11k_warn(ar->ab,
+					    "failed to set BA BUFFER SIZE 256 for vdev: %d\n",
+					    arvif->vdev_id);
+			else
+				ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
+					   "Set BA BUFFER SIZE 256 for VDEV: %d\n",
+					   arvif->vdev_id);
+		}
 	}
 
 	if (changed & (BSS_CHANGED_BEACON_INFO | BSS_CHANGED_BEACON)) {
@@ -2186,14 +2204,6 @@
 
 		if (arvif->is_up && vif->bss_conf.he_support &&
 		    vif->bss_conf.he_oper.params) {
-			ret = ath11k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-							    WMI_VDEV_PARAM_BA_MODE,
-							    WMI_BA_MODE_BUFFER_SIZE_256);
-			if (ret)
-				ath11k_warn(ar->ab,
-					    "failed to set BA BUFFER SIZE 256 for vdev: %d\n",
-					    arvif->vdev_id);
-
 			param_id = WMI_VDEV_PARAM_HEOPS_0_31;
 			param_value = vif->bss_conf.he_oper.params;
 			ret = ath11k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
@@ -2576,9 +2586,12 @@
 	arg.scan_id = ATH11K_SCAN_ID;
 
 	if (req->ie_len) {
+		arg.extraie.ptr = kmemdup(req->ie, req->ie_len, GFP_KERNEL);
+		if (!arg.extraie.ptr) {
+			ret = -ENOMEM;
+			goto exit;
+		}
 		arg.extraie.len = req->ie_len;
-		arg.extraie.ptr = kzalloc(req->ie_len, GFP_KERNEL);
-		memcpy(arg.extraie.ptr, req->ie, req->ie_len);
 	}
 
 	if (req->n_ssids) {
@@ -2594,6 +2607,14 @@
 
 	if (req->n_channels) {
 		arg.num_chan = req->n_channels;
+		arg.chan_list = kcalloc(arg.num_chan, sizeof(*arg.chan_list),
+					GFP_KERNEL);
+
+		if (!arg.chan_list) {
+			ret = -ENOMEM;
+			goto exit;
+		}
+
 		for (i = 0; i < arg.num_chan; i++)
 			arg.chan_list[i] = req->channels[i]->center_freq;
 	}
@@ -2612,6 +2633,8 @@
 						      ATH11K_MAC_SCAN_TIMEOUT_MSECS));
 
 exit:
+	kfree(arg.chan_list);
+
 	if (req->ie_len)
 		kfree(arg.extraie.ptr);
 
@@ -2655,15 +2678,14 @@
 		return 0;
 
 	if (cmd == DISABLE_KEY) {
-		/* TODO: Check if FW expects  value other than NONE for del */
-		/* arg.key_cipher = WMI_CIPHER_NONE; */
-		arg.key_len = 0;
+		arg.key_cipher = WMI_CIPHER_NONE;
 		arg.key_data = NULL;
 		goto install;
 	}
 
 	switch (key->cipher) {
 	case WLAN_CIPHER_SUITE_CCMP:
+	case WLAN_CIPHER_SUITE_CCMP_256:
 		arg.key_cipher = WMI_CIPHER_AES_CCM;
 		/* TODO: Re-check if flag is valid */
 		key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV_MGMT;
@@ -2673,12 +2695,10 @@
 		arg.key_txmic_len = 8;
 		arg.key_rxmic_len = 8;
 		break;
-	case WLAN_CIPHER_SUITE_CCMP_256:
-		arg.key_cipher = WMI_CIPHER_AES_CCM;
-		break;
 	case WLAN_CIPHER_SUITE_GCMP:
 	case WLAN_CIPHER_SUITE_GCMP_256:
 		arg.key_cipher = WMI_CIPHER_AES_GCM;
+		key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV_MGMT;
 		break;
 	default:
 		ath11k_warn(ar->ab, "cipher %d is not supported\n", key->cipher);
@@ -2789,7 +2809,7 @@
 	/* flush the fragments cache during key (re)install to
 	 * ensure all frags in the new frag list belong to the same key.
 	 */
-	if (peer && cmd == SET_KEY)
+	if (peer && sta && cmd == SET_KEY)
 		ath11k_peer_frags_flush(ar, peer);
 	spin_unlock_bh(&ab->base_lock);
 
@@ -3673,6 +3693,8 @@
 	if (vht_cap & (IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE)) {
 		nsts = vht_cap & IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK;
 		nsts >>= IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT;
+		if (nsts > (ar->num_rx_chains - 1))
+			nsts = ar->num_rx_chains - 1;
 		value |= SM(nsts, WMI_TXBF_STS_CAP_OFFSET);
 	}
 
@@ -3713,7 +3735,7 @@
 static void ath11k_set_vht_txbf_cap(struct ath11k *ar, u32 *vht_cap)
 {
 	bool subfer, subfee;
-	int sound_dim = 0;
+	int sound_dim = 0, nsts = 0;
 
 	subfer = !!(*vht_cap & (IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE));
 	subfee = !!(*vht_cap & (IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE));
@@ -3723,6 +3745,11 @@
 		subfer = false;
 	}
 
+	if (ar->num_rx_chains < 2) {
+		*vht_cap &= ~(IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE);
+		subfee = false;
+	}
+
 	/* If SU Beaformer is not set, then disable MU Beamformer Capability */
 	if (!subfer)
 		*vht_cap &= ~(IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE);
@@ -3735,7 +3762,9 @@
 	sound_dim >>= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT;
 	*vht_cap &= ~IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK;
 
-	/* TODO: Need to check invalid STS and Sound_dim values set by FW? */
+	nsts = (*vht_cap & IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK);
+	nsts >>= IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT;
+	*vht_cap &= ~IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK;
 
 	/* Enable Sounding Dimension Field only if SU BF is enabled */
 	if (subfer) {
@@ -3747,9 +3776,15 @@
 		*vht_cap |= sound_dim;
 	}
 
-	/* Use the STS advertised by FW unless SU Beamformee is not supported*/
-	if (!subfee)
-		*vht_cap &= ~(IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK);
+	/* Enable Beamformee STS Field only if SU BF is enabled */
+	if (subfee) {
+		if (nsts > (ar->num_rx_chains - 1))
+			nsts = ar->num_rx_chains - 1;
+
+		nsts <<= IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT;
+		nsts &=  IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK;
+		*vht_cap |= nsts;
+	}
 }
 
 static struct ieee80211_sta_vht_cap
@@ -4131,23 +4166,32 @@
 	return 0;
 }
 
-int ath11k_mac_tx_mgmt_pending_free(int buf_id, void *skb, void *ctx)
+static void ath11k_mac_tx_mgmt_free(struct ath11k *ar, int buf_id)
 {
-	struct sk_buff *msdu = skb;
+	struct sk_buff *msdu;
 	struct ieee80211_tx_info *info;
-	struct ath11k *ar = ctx;
-	struct ath11k_base *ab = ar->ab;
 
 	spin_lock_bh(&ar->txmgmt_idr_lock);
-	idr_remove(&ar->txmgmt_idr, buf_id);
+	msdu = idr_remove(&ar->txmgmt_idr, buf_id);
 	spin_unlock_bh(&ar->txmgmt_idr_lock);
-	dma_unmap_single(ab->dev, ATH11K_SKB_CB(msdu)->paddr, msdu->len,
+
+	if (!msdu)
+		return;
+
+	dma_unmap_single(ar->ab->dev, ATH11K_SKB_CB(msdu)->paddr, msdu->len,
 			 DMA_TO_DEVICE);
 
 	info = IEEE80211_SKB_CB(msdu);
 	memset(&info->status, 0, sizeof(info->status));
 
 	ieee80211_free_txskb(ar->hw, msdu);
+}
+
+int ath11k_mac_tx_mgmt_pending_free(int buf_id, void *skb, void *ctx)
+{
+	struct ath11k *ar = ctx;
+
+	ath11k_mac_tx_mgmt_free(ar, buf_id);
 
 	return 0;
 }
@@ -4156,17 +4200,10 @@
 {
 	struct ieee80211_vif *vif = ctx;
 	struct ath11k_skb_cb *skb_cb = ATH11K_SKB_CB((struct sk_buff *)skb);
-	struct sk_buff *msdu = skb;
 	struct ath11k *ar = skb_cb->ar;
-	struct ath11k_base *ab = ar->ab;
 
-	if (skb_cb->vif == vif) {
-		spin_lock_bh(&ar->txmgmt_idr_lock);
-		idr_remove(&ar->txmgmt_idr, buf_id);
-		spin_unlock_bh(&ar->txmgmt_idr_lock);
-		dma_unmap_single(ab->dev, skb_cb->paddr, msdu->len,
-				 DMA_TO_DEVICE);
-	}
+	if (skb_cb->vif == vif)
+		ath11k_mac_tx_mgmt_free(ar, buf_id);
 
 	return 0;
 }
@@ -4176,11 +4213,16 @@
 {
 	struct ath11k_base *ab = ar->ab;
 	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+	struct ath11k_skb_cb *skb_cb = ATH11K_SKB_CB(skb);
 	struct ieee80211_tx_info *info;
+	enum hal_encrypt_type enctype;
+	unsigned int mic_len;
 	dma_addr_t paddr;
 	int buf_id;
 	int ret;
 
+	ATH11K_SKB_CB(skb)->ar = ar;
+
 	spin_lock_bh(&ar->txmgmt_idr_lock);
 	buf_id = idr_alloc(&ar->txmgmt_idr, skb, 0,
 			   ATH11K_TX_MGMT_NUM_PENDING_MAX, GFP_ATOMIC);
@@ -4194,7 +4236,12 @@
 		     ieee80211_is_deauth(hdr->frame_control) ||
 		     ieee80211_is_disassoc(hdr->frame_control)) &&
 		     ieee80211_has_protected(hdr->frame_control)) {
-			skb_put(skb, IEEE80211_CCMP_MIC_LEN);
+			if (!(skb_cb->flags & ATH11K_SKB_CIPHER_SET))
+				ath11k_warn(ab, "WMI management tx frame without ATH11K_SKB_CIPHER_SET");
+
+			enctype = ath11k_dp_tx_get_encrypt_type(skb_cb->cipher);
+			mic_len = ath11k_dp_rx_crypto_mic_len(ar, enctype);
+			skb_put(skb, mic_len);
 		}
 	}
 
@@ -4251,8 +4298,8 @@
 		}
 
 		arvif = ath11k_vif_to_arvif(skb_cb->vif);
-		if (ar->allocated_vdev_map & (1LL << arvif->vdev_id) &&
-		    arvif->is_started) {
+		mutex_lock(&ar->conf_mutex);
+		if (ar->allocated_vdev_map & (1LL << arvif->vdev_id)) {
 			ret = ath11k_mac_mgmt_tx_wmi(ar, arvif, skb);
 			if (ret) {
 				ath11k_warn(ar->ab, "failed to tx mgmt frame, vdev_id %d :%d\n",
@@ -4268,6 +4315,7 @@
 				    arvif->is_started);
 			ieee80211_free_txskb(ar->hw, skb);
 		}
+		mutex_unlock(&ar->conf_mutex);
 	}
 }
 
@@ -5577,6 +5625,7 @@
 	struct ath11k *ar = hw->priv;
 	struct ath11k_base *ab = ar->ab;
 	struct ath11k_vif *arvif = (void *)vif->drv_priv;
+	struct ath11k_peer *peer;
 	int ret;
 
 	mutex_lock(&ar->conf_mutex);
@@ -5588,9 +5637,13 @@
 	WARN_ON(!arvif->is_started);
 
 	if (ab->hw_params.vdev_start_delay &&
-	    arvif->vdev_type == WMI_VDEV_TYPE_MONITOR &&
-	    ath11k_peer_find_by_addr(ab, ar->mac_addr))
-		ath11k_peer_delete(ar, arvif->vdev_id, ar->mac_addr);
+	    arvif->vdev_type == WMI_VDEV_TYPE_MONITOR) {
+		spin_lock_bh(&ab->base_lock);
+		peer = ath11k_peer_find_by_addr(ab, ar->mac_addr);
+		spin_unlock_bh(&ab->base_lock);
+		if (peer)
+			ath11k_peer_delete(ar, arvif->vdev_id, ar->mac_addr);
+	}
 
 	ret = ath11k_mac_vdev_stop(arvif);
 	if (ret)
@@ -6276,7 +6329,7 @@
 	}
 
 	if (supported_bands & WMI_HOST_WLAN_5G_CAP) {
-		if (reg_cap->high_5ghz_chan >= ATH11K_MAX_6G_FREQ) {
+		if (reg_cap->high_5ghz_chan >= ATH11K_MIN_6G_FREQ) {
 			channels = kmemdup(ath11k_6ghz_channels,
 					   sizeof(ath11k_6ghz_channels), GFP_KERNEL);
 			if (!channels) {
@@ -6545,7 +6598,7 @@
 	ar->hw->queues = ATH11K_HW_MAX_QUEUES;
 	ar->hw->wiphy->tx_queue_len = ATH11K_QUEUE_LEN;
 	ar->hw->offchannel_tx_hw_queue = ATH11K_HW_MAX_QUEUES - 1;
-	ar->hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
+	ar->hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
 
 	ar->hw->vif_data_size = sizeof(struct ath11k_vif);
 	ar->hw->sta_data_size = sizeof(struct ath11k_sta);
@@ -6590,7 +6643,7 @@
 		ar->hw->wiphy->interface_modes &= ~BIT(NL80211_IFTYPE_MONITOR);
 
 	/* Apply the regd received during initialization */
-	ret = ath11k_regd_update(ar, true);
+	ret = ath11k_regd_update(ar);
 	if (ret) {
 		ath11k_err(ar->ab, "ath11k regd update failed: %d\n", ret);
 		goto err_unregister_hw;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/mhi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/mhi.c
@@ -97,7 +97,7 @@
 	.max_channels = 128,
 	.timeout_ms = 2000,
 	.use_bounce_buf = false,
-	.buf_len = 0,
+	.buf_len = 8192,
 	.num_channels = ARRAY_SIZE(ath11k_mhi_channels_qca6390),
 	.ch_cfg = ath11k_mhi_channels_qca6390,
 	.num_events = ARRAY_SIZE(ath11k_mhi_events_qca6390),
@@ -519,7 +519,7 @@
 		ret = 0;
 		break;
 	case ATH11K_MHI_POWER_ON:
-		ret = mhi_async_power_up(ab_pci->mhi_ctrl);
+		ret = mhi_sync_power_up(ab_pci->mhi_ctrl);
 		break;
 	case ATH11K_MHI_POWER_OFF:
 		mhi_power_down(ab_pci->mhi_ctrl, true);
@@ -533,7 +533,11 @@
 		ret = mhi_pm_suspend(ab_pci->mhi_ctrl);
 		break;
 	case ATH11K_MHI_RESUME:
-		ret = mhi_pm_resume(ab_pci->mhi_ctrl);
+		/* Do force MHI resume as some devices like QCA6390, WCN6855
+		 * are not in M3 state but they are functional. So just ignore
+		 * the MHI state while resuming.
+		 */
+		ret = mhi_pm_resume_force(ab_pci->mhi_ctrl);
 		break;
 	case ATH11K_MHI_TRIGGER_RDDM:
 		ret = mhi_force_rddm_mode(ab_pci->mhi_ctrl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/pci.c
@@ -25,7 +25,7 @@
 #define WINDOW_RANGE_MASK		GENMASK(18, 0)
 
 #define TCSR_SOC_HW_VERSION		0x0224
-#define TCSR_SOC_HW_VERSION_MAJOR_MASK	GENMASK(16, 8)
+#define TCSR_SOC_HW_VERSION_MAJOR_MASK	GENMASK(11, 8)
 #define TCSR_SOC_HW_VERSION_MINOR_MASK	GENMASK(7, 0)
 
 /* BAR0 + 4k is always accessible, and no
@@ -182,7 +182,8 @@
 	/* for offset beyond BAR + 4K - 32, may
 	 * need to wakeup MHI to access.
 	 */
-	if (test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
+	if (ab->hw_params.wakeup_mhi &&
+	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
 	    offset >= ACCESS_ALWAYS_OFF)
 		mhi_device_get_sync(ab_pci->mhi_ctrl->mhi_dev);
 
@@ -206,7 +207,8 @@
 		}
 	}
 
-	if (test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
+	if (ab->hw_params.wakeup_mhi &&
+	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
 	    offset >= ACCESS_ALWAYS_OFF)
 		mhi_device_put(ab_pci->mhi_ctrl->mhi_dev);
 }
@@ -219,7 +221,8 @@
 	/* for offset beyond BAR + 4K - 32, may
 	 * need to wakeup MHI to access.
 	 */
-	if (test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
+	if (ab->hw_params.wakeup_mhi &&
+	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
 	    offset >= ACCESS_ALWAYS_OFF)
 		mhi_device_get_sync(ab_pci->mhi_ctrl->mhi_dev);
 
@@ -243,7 +246,8 @@
 		}
 	}
 
-	if (test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
+	if (ab->hw_params.wakeup_mhi &&
+	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
 	    offset >= ACCESS_ALWAYS_OFF)
 		mhi_device_put(ab_pci->mhi_ctrl->mhi_dev);
 
@@ -632,8 +636,11 @@
 
 		ath11k_pci_ext_grp_disable(irq_grp);
 
-		napi_synchronize(&irq_grp->napi);
-		napi_disable(&irq_grp->napi);
+		if (irq_grp->napi_enabled) {
+			napi_synchronize(&irq_grp->napi);
+			napi_disable(&irq_grp->napi);
+			irq_grp->napi_enabled = false;
+		}
 	}
 }
 
@@ -652,7 +659,10 @@
 	for (i = 0; i < ATH11K_EXT_IRQ_GRP_NUM_MAX; i++) {
 		struct ath11k_ext_irq_grp *irq_grp = &ab->ext_irq_grp[i];
 
-		napi_enable(&irq_grp->napi);
+		if (!irq_grp->napi_enabled) {
+			napi_enable(&irq_grp->napi);
+			irq_grp->napi_enabled = true;
+		}
 		ath11k_pci_ext_grp_enable(irq_grp);
 	}
 }
@@ -990,8 +1000,8 @@
 		   u16_get_bits(ab_pci->link_ctl, PCI_EXP_LNKCTL_ASPM_L1));
 
 	/* disable L0s and L1 */
-	pcie_capability_write_word(ab_pci->pdev, PCI_EXP_LNKCTL,
-				   ab_pci->link_ctl & ~PCI_EXP_LNKCTL_ASPMC);
+	pcie_capability_clear_word(ab_pci->pdev, PCI_EXP_LNKCTL,
+				   PCI_EXP_LNKCTL_ASPMC);
 
 	set_bit(ATH11K_PCI_ASPM_RESTORE, &ab_pci->flags);
 }
@@ -999,8 +1009,10 @@
 static void ath11k_pci_aspm_restore(struct ath11k_pci *ab_pci)
 {
 	if (test_and_clear_bit(ATH11K_PCI_ASPM_RESTORE, &ab_pci->flags))
-		pcie_capability_write_word(ab_pci->pdev, PCI_EXP_LNKCTL,
-					   ab_pci->link_ctl);
+		pcie_capability_clear_and_set_word(ab_pci->pdev, PCI_EXP_LNKCTL,
+						   PCI_EXP_LNKCTL_ASPMC,
+						   ab_pci->link_ctl &
+						   PCI_EXP_LNKCTL_ASPMC);
 }
 
 static int ath11k_pci_power_up(struct ath11k_base *ab)
@@ -1218,6 +1230,15 @@
 		goto err_free_core;
 	}
 
+	ath11k_dbg(ab, ATH11K_DBG_BOOT, "pci probe %04x:%04x %04x:%04x\n",
+		   pdev->vendor, pdev->device,
+		   pdev->subsystem_vendor, pdev->subsystem_device);
+
+	ab->id.vendor = pdev->vendor;
+	ab->id.device = pdev->device;
+	ab->id.subsystem_vendor = pdev->subsystem_vendor;
+	ab->id.subsystem_device = pdev->subsystem_device;
+
 	switch (pci_dev->device) {
 	case QCA6390_DEVICE_ID:
 		ath11k_pci_read_hw_version(ab, &soc_hw_version_major,
@@ -1240,6 +1261,7 @@
 		ab->hw_rev = ATH11K_HW_QCN9074_HW10;
 		break;
 	case WCN6855_DEVICE_ID:
+		ab->id.bdf_search = ATH11K_BDF_SEARCH_BUS_AND_BOARD;
 		ath11k_pci_read_hw_version(ab, &soc_hw_version_major,
 					   &soc_hw_version_minor);
 		switch (soc_hw_version_major) {
@@ -1366,11 +1388,16 @@
 	struct ath11k_base *ab = dev_get_drvdata(dev);
 	int ret;
 
+	if (test_bit(ATH11K_FLAG_QMI_FAIL, &ab->dev_flags)) {
+		ath11k_dbg(ab, ATH11K_DBG_BOOT, "boot skipping pci suspend as qmi is not initialised\n");
+		return 0;
+	}
+
 	ret = ath11k_core_suspend(ab);
 	if (ret)
 		ath11k_warn(ab, "failed to suspend core: %d\n", ret);
 
-	return ret;
+	return 0;
 }
 
 static __maybe_unused int ath11k_pci_pm_resume(struct device *dev)
@@ -1378,6 +1405,11 @@
 	struct ath11k_base *ab = dev_get_drvdata(dev);
 	int ret;
 
+	if (test_bit(ATH11K_FLAG_QMI_FAIL, &ab->dev_flags)) {
+		ath11k_dbg(ab, ATH11K_DBG_BOOT, "boot skipping pci resume as qmi is not initialised\n");
+		return 0;
+	}
+
 	ret = ath11k_core_resume(ab);
 	if (ret)
 		ath11k_warn(ab, "failed to resume core: %d\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/qmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/qmi.c
@@ -1770,7 +1770,7 @@
 		chunk->vaddr = dma_alloc_coherent(ab->dev,
 						  chunk->size,
 						  &chunk->paddr,
-						  GFP_KERNEL);
+						  GFP_KERNEL | __GFP_NOWARN);
 		if (!chunk->vaddr) {
 			if (ab->qmi.mem_seg_count <= ATH11K_QMI_FW_MEM_REQ_SEGMENT_CNT) {
 				ath11k_dbg(ab, ATH11K_DBG_QMI,
@@ -2707,8 +2707,10 @@
 		list_del(&event->list);
 		spin_unlock(&qmi->event_lock);
 
-		if (test_bit(ATH11K_FLAG_UNREGISTERING, &ab->dev_flags))
+		if (test_bit(ATH11K_FLAG_UNREGISTERING, &ab->dev_flags)) {
+			kfree(event);
 			return;
+		}
 
 		switch (event->type) {
 		case ATH11K_QMI_EVENT_SERVER_ARRIVE:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/qmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/qmi.h
@@ -27,7 +27,7 @@
 #define ATH11K_QMI_WLANFW_MAX_NUM_MEM_SEG_V01	52
 #define ATH11K_QMI_CALDB_SIZE			0x480000
 #define ATH11K_QMI_BDF_EXT_STR_LENGTH		0x20
-#define ATH11K_QMI_FW_MEM_REQ_SEGMENT_CNT	3
+#define ATH11K_QMI_FW_MEM_REQ_SEGMENT_CNT	5
 
 #define QMI_WLFW_REQUEST_MEM_IND_V01		0x0035
 #define QMI_WLFW_FW_MEM_READY_IND_V01		0x0037
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/reg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/reg.c
@@ -198,7 +198,7 @@
 		       sizeof(struct ieee80211_reg_rule));
 }
 
-int ath11k_regd_update(struct ath11k *ar, bool init)
+int ath11k_regd_update(struct ath11k *ar)
 {
 	struct ieee80211_regdomain *regd, *regd_copy = NULL;
 	int ret, regd_len, pdev_id;
@@ -209,7 +209,10 @@
 
 	spin_lock_bh(&ab->base_lock);
 
-	if (init) {
+	/* Prefer the latest regd update over default if it's available */
+	if (ab->new_regd[pdev_id]) {
+		regd = ab->new_regd[pdev_id];
+	} else {
 		/* Apply the regd received during init through
 		 * WMI_REG_CHAN_LIST_CC event. In case of failure to
 		 * receive the regd, initialize with a default world
@@ -222,8 +225,6 @@
 				    "failed to receive default regd during init\n");
 			regd = (struct ieee80211_regdomain *)&ath11k_world_regd;
 		}
-	} else {
-		regd = ab->new_regd[pdev_id];
 	}
 
 	if (!regd) {
@@ -246,11 +247,7 @@
 		goto err;
 	}
 
-	rtnl_lock();
-	wiphy_lock(ar->hw->wiphy);
-	ret = regulatory_set_wiphy_regd_sync(ar->hw->wiphy, regd_copy);
-	wiphy_unlock(ar->hw->wiphy);
-	rtnl_unlock();
+	ret = regulatory_set_wiphy_regd(ar->hw->wiphy, regd_copy);
 
 	kfree(regd_copy);
 
@@ -458,6 +455,9 @@
 {
 	u16 bw;
 
+	if (end_freq <= start_freq)
+		return 0;
+
 	bw = end_freq - start_freq;
 	bw = min_t(u16, bw, max_bw);
 
@@ -465,8 +465,10 @@
 		bw = 80;
 	else if (bw >= 40 && bw < 80)
 		bw = 40;
-	else if (bw < 40)
+	else if (bw >= 20 && bw < 40)
 		bw = 20;
+	else
+		bw = 0;
 
 	return bw;
 }
@@ -490,73 +492,77 @@
 				     struct cur_reg_rule *reg_rule,
 				     u8 *rule_idx, u32 flags, u16 max_bw)
 {
+	u32 start_freq;
 	u32 end_freq;
 	u16 bw;
 	u8 i;
 
 	i = *rule_idx;
 
+	/* there might be situations when even the input rule must be dropped */
+	i--;
+
+	/* frequencies below weather radar */
 	bw = ath11k_reg_adjust_bw(reg_rule->start_freq,
 				  ETSI_WEATHER_RADAR_BAND_LOW, max_bw);
+	if (bw > 0) {
+		i++;
 
-	ath11k_reg_update_rule(regd->reg_rules + i, reg_rule->start_freq,
-			       ETSI_WEATHER_RADAR_BAND_LOW, bw,
-			       reg_rule->ant_gain, reg_rule->reg_power,
-			       flags);
-
-	ath11k_dbg(ab, ATH11K_DBG_REG,
-		   "\t%d. (%d - %d @ %d) (%d, %d) (%d ms) (FLAGS %d)\n",
-		   i + 1, reg_rule->start_freq, ETSI_WEATHER_RADAR_BAND_LOW,
-		   bw, reg_rule->ant_gain, reg_rule->reg_power,
-		   regd->reg_rules[i].dfs_cac_ms,
-		   flags);
-
-	if (reg_rule->end_freq > ETSI_WEATHER_RADAR_BAND_HIGH)
-		end_freq = ETSI_WEATHER_RADAR_BAND_HIGH;
-	else
-		end_freq = reg_rule->end_freq;
-
-	bw = ath11k_reg_adjust_bw(ETSI_WEATHER_RADAR_BAND_LOW, end_freq,
-				  max_bw);
+		ath11k_reg_update_rule(regd->reg_rules + i,
+				       reg_rule->start_freq,
+				       ETSI_WEATHER_RADAR_BAND_LOW, bw,
+				       reg_rule->ant_gain, reg_rule->reg_power,
+				       flags);
 
-	i++;
+		ath11k_dbg(ab, ATH11K_DBG_REG,
+			   "\t%d. (%d - %d @ %d) (%d, %d) (%d ms) (FLAGS %d)\n",
+			   i + 1, reg_rule->start_freq,
+			   ETSI_WEATHER_RADAR_BAND_LOW, bw, reg_rule->ant_gain,
+			   reg_rule->reg_power, regd->reg_rules[i].dfs_cac_ms,
+			   flags);
+	}
 
-	ath11k_reg_update_rule(regd->reg_rules + i,
-			       ETSI_WEATHER_RADAR_BAND_LOW, end_freq, bw,
-			       reg_rule->ant_gain, reg_rule->reg_power,
-			       flags);
+	/* weather radar frequencies */
+	start_freq = max_t(u32, reg_rule->start_freq,
+			   ETSI_WEATHER_RADAR_BAND_LOW);
+	end_freq = min_t(u32, reg_rule->end_freq, ETSI_WEATHER_RADAR_BAND_HIGH);
+
+	bw = ath11k_reg_adjust_bw(start_freq, end_freq, max_bw);
+	if (bw > 0) {
+		i++;
+
+		ath11k_reg_update_rule(regd->reg_rules + i, start_freq,
+				       end_freq, bw, reg_rule->ant_gain,
+				       reg_rule->reg_power, flags);
 
-	regd->reg_rules[i].dfs_cac_ms = ETSI_WEATHER_RADAR_BAND_CAC_TIMEOUT;
+		regd->reg_rules[i].dfs_cac_ms = ETSI_WEATHER_RADAR_BAND_CAC_TIMEOUT;
 
-	ath11k_dbg(ab, ATH11K_DBG_REG,
-		   "\t%d. (%d - %d @ %d) (%d, %d) (%d ms) (FLAGS %d)\n",
-		   i + 1, ETSI_WEATHER_RADAR_BAND_LOW, end_freq,
-		   bw, reg_rule->ant_gain, reg_rule->reg_power,
-		   regd->reg_rules[i].dfs_cac_ms,
-		   flags);
-
-	if (end_freq == reg_rule->end_freq) {
-		regd->n_reg_rules--;
-		*rule_idx = i;
-		return;
+		ath11k_dbg(ab, ATH11K_DBG_REG,
+			   "\t%d. (%d - %d @ %d) (%d, %d) (%d ms) (FLAGS %d)\n",
+			   i + 1, start_freq, end_freq, bw,
+			   reg_rule->ant_gain, reg_rule->reg_power,
+			   regd->reg_rules[i].dfs_cac_ms, flags);
 	}
 
+	/* frequencies above weather radar */
 	bw = ath11k_reg_adjust_bw(ETSI_WEATHER_RADAR_BAND_HIGH,
 				  reg_rule->end_freq, max_bw);
+	if (bw > 0) {
+		i++;
 
-	i++;
-
-	ath11k_reg_update_rule(regd->reg_rules + i, ETSI_WEATHER_RADAR_BAND_HIGH,
-			       reg_rule->end_freq, bw,
-			       reg_rule->ant_gain, reg_rule->reg_power,
-			       flags);
+		ath11k_reg_update_rule(regd->reg_rules + i,
+				       ETSI_WEATHER_RADAR_BAND_HIGH,
+				       reg_rule->end_freq, bw,
+				       reg_rule->ant_gain, reg_rule->reg_power,
+				       flags);
 
-	ath11k_dbg(ab, ATH11K_DBG_REG,
-		   "\t%d. (%d - %d @ %d) (%d, %d) (%d ms) (FLAGS %d)\n",
-		   i + 1, ETSI_WEATHER_RADAR_BAND_HIGH, reg_rule->end_freq,
-		   bw, reg_rule->ant_gain, reg_rule->reg_power,
-		   regd->reg_rules[i].dfs_cac_ms,
-		   flags);
+		ath11k_dbg(ab, ATH11K_DBG_REG,
+			   "\t%d. (%d - %d @ %d) (%d, %d) (%d ms) (FLAGS %d)\n",
+			   i + 1, ETSI_WEATHER_RADAR_BAND_HIGH,
+			   reg_rule->end_freq, bw, reg_rule->ant_gain,
+			   reg_rule->reg_power, regd->reg_rules[i].dfs_cac_ms,
+			   flags);
+	}
 
 	*rule_idx = i;
 }
@@ -683,7 +689,7 @@
 					 regd_update_work);
 	int ret;
 
-	ret = ath11k_regd_update(ar, false);
+	ret = ath11k_regd_update(ar);
 	if (ret) {
 		/* Firmware has already moved to the new regd. We need
 		 * to maintain channel consistency across FW, Host driver
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/reg.h
@@ -31,6 +31,6 @@
 struct ieee80211_regdomain *
 ath11k_reg_build_regd(struct ath11k_base *ab,
 		      struct cur_regulatory_info *reg_info, bool intersect);
-int ath11k_regd_update(struct ath11k *ar, bool init);
+int ath11k_regd_update(struct ath11k *ar);
 int ath11k_reg_update_chan_list(struct ath11k *ar);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/spectral.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/spectral.c
@@ -214,7 +214,10 @@
 		return -ENODEV;
 
 	arvif->spectral_enabled = (mode != ATH11K_SPECTRAL_DISABLED);
+
+	spin_lock_bh(&ar->spectral.lock);
 	ar->spectral.mode = mode;
+	spin_unlock_bh(&ar->spectral.lock);
 
 	ret = ath11k_wmi_vdev_spectral_enable(ar, arvif->vdev_id,
 					      ATH11K_WMI_SPECTRAL_TRIGGER_CMD_CLEAR,
@@ -829,9 +832,6 @@
 {
 	struct ath11k_spectral *sp = &ar->spectral;
 
-	if (!sp->enabled)
-		return;
-
 	ath11k_dbring_srng_cleanup(ar, &sp->rx_ring);
 	ath11k_dbring_buf_cleanup(ar, &sp->rx_ring);
 }
@@ -883,15 +883,16 @@
 		if (!sp->enabled)
 			continue;
 
-		ath11k_spectral_debug_unregister(ar);
-		ath11k_spectral_ring_free(ar);
+		mutex_lock(&ar->conf_mutex);
+		ath11k_spectral_scan_config(ar, ATH11K_SPECTRAL_DISABLED);
+		mutex_unlock(&ar->conf_mutex);
 
 		spin_lock_bh(&sp->lock);
-
-		sp->mode = ATH11K_SPECTRAL_DISABLED;
 		sp->enabled = false;
-
 		spin_unlock_bh(&sp->lock);
+
+		ath11k_spectral_debug_unregister(ar);
+		ath11k_spectral_ring_free(ar);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/wmi.c
@@ -1339,6 +1339,7 @@
 				     WMI_TAG_PDEV_BSS_CHAN_INFO_REQUEST) |
 			  FIELD_PREP(WMI_TLV_LEN, sizeof(*cmd) - TLV_HDR_SIZE);
 	cmd->req_type = type;
+	cmd->pdev_id = ar->pdev->pdev_id;
 
 	ath11k_dbg(ar->ab, ATH11K_DBG_WMI,
 		   "WMI bss chan info req type %d\n", type);
@@ -1670,7 +1671,8 @@
 	tlv = (struct wmi_tlv *)(skb->data + sizeof(*cmd));
 	tlv->header = FIELD_PREP(WMI_TLV_TAG, WMI_TAG_ARRAY_BYTE) |
 		      FIELD_PREP(WMI_TLV_LEN, key_len_aligned);
-	memcpy(tlv->value, (u8 *)arg->key_data, key_len_aligned);
+	if (arg->key_data)
+		memcpy(tlv->value, (u8 *)arg->key_data, key_len_aligned);
 
 	ret = ath11k_wmi_cmd_send(wmi, skb, WMI_VDEV_INSTALL_KEY_CMDID);
 	if (ret) {
@@ -2050,7 +2052,7 @@
 	void *ptr;
 	int i, ret, len;
 	u32 *tmp_ptr;
-	u8 extraie_len_with_pad = 0;
+	u16 extraie_len_with_pad = 0;
 	struct hint_short_ssid *s_ssid = NULL;
 	struct hint_bssid *hint_bssid = NULL;
 
@@ -2069,7 +2071,7 @@
 		len += sizeof(*bssid) * params->num_bssid;
 
 	len += TLV_HDR_SIZE;
-	if (params->extraie.len)
+	if (params->extraie.len && params->extraie.len <= 0xFFFF)
 		extraie_len_with_pad =
 			roundup(params->extraie.len, sizeof(u32));
 	len += extraie_len_with_pad;
@@ -2176,7 +2178,7 @@
 		      FIELD_PREP(WMI_TLV_LEN, len);
 	ptr += TLV_HDR_SIZE;
 
-	if (params->extraie.len)
+	if (extraie_len_with_pad)
 		memcpy(ptr, params->extraie.ptr,
 		       params->extraie.len);
 
@@ -5792,6 +5794,17 @@
 
 	pdev_idx = reg_info->phy_id;
 
+	/* Avoid default reg rule updates sent during FW recovery if
+	 * it is already available
+	 */
+	spin_lock(&ab->base_lock);
+	if (test_bit(ATH11K_FLAG_RECOVERY, &ab->dev_flags) &&
+	    ab->default_regd[pdev_idx]) {
+		spin_unlock(&ab->base_lock);
+		goto mem_free;
+	}
+	spin_unlock(&ab->base_lock);
+
 	if (pdev_idx >= ab->num_radios) {
 		/* Process the event for phy0 only if single_pdev_only
 		 * is true. If pdev_idx is valid but not 0, discard the
@@ -5829,10 +5842,10 @@
 	}
 
 	spin_lock(&ab->base_lock);
-	if (test_bit(ATH11K_FLAG_REGISTERED, &ab->dev_flags)) {
-		/* Once mac is registered, ar is valid and all CC events from
-		 * fw is considered to be received due to user requests
-		 * currently.
+	if (ab->default_regd[pdev_idx]) {
+		/* The initial rules from FW after WMI Init is to build
+		 * the default regd. From then on, any rules updated for
+		 * the pdev could be due to user reg changes.
 		 * Free previously built regd before assigning the newly
 		 * generated regd to ar. NULL pointer handling will be
 		 * taken care by kfree itself.
@@ -5840,15 +5853,11 @@
 		ar = ab->pdevs[pdev_idx].ar;
 		kfree(ab->new_regd[pdev_idx]);
 		ab->new_regd[pdev_idx] = regd;
-		ieee80211_queue_work(ar->hw, &ar->regd_update_work);
+		queue_work(ab->workqueue, &ar->regd_update_work);
 	} else {
-		/* Multiple events for the same *ar is not expected. But we
-		 * can still clear any previously stored default_regd if we
-		 * are receiving this event for the same radio by mistake.
-		 * NULL pointer handling will be taken care by kfree itself.
+		/* This regd would be applied during mac registration and is
+		 * held constant throughout for regd intersection purpose
 		 */
-		kfree(ab->default_regd[pdev_idx]);
-		/* This regd would be applied during mac registration */
 		ab->default_regd[pdev_idx] = regd;
 	}
 	ab->dfs_region = reg_info->dfs_region;
@@ -6119,8 +6128,10 @@
 	if (rx_ev.status & WMI_RX_STATUS_ERR_MIC)
 		status->flag |= RX_FLAG_MMIC_ERROR;
 
-	if (rx_ev.chan_freq >= ATH11K_MIN_6G_FREQ) {
+	if (rx_ev.chan_freq >= ATH11K_MIN_6G_FREQ &&
+	    rx_ev.chan_freq <= ATH11K_MAX_6G_FREQ) {
 		status->band = NL80211_BAND_6GHZ;
+		status->freq = rx_ev.chan_freq;
 	} else if (rx_ev.channel >= 1 && rx_ev.channel <= 14) {
 		status->band = NL80211_BAND_2GHZ;
 	} else if (rx_ev.channel >= 36 && rx_ev.channel <= ATH11K_MAX_5G_CHAN) {
@@ -6141,8 +6152,10 @@
 
 	sband = &ar->mac.sbands[status->band];
 
-	status->freq = ieee80211_channel_to_frequency(rx_ev.channel,
-						      status->band);
+	if (status->band != NL80211_BAND_6GHZ)
+		status->freq = ieee80211_channel_to_frequency(rx_ev.channel,
+							      status->band);
+
 	status->signal = rx_ev.snr + ATH11K_DEFAULT_NOISE_FLOOR;
 	status->rate_idx = ath11k_mac_bitrate_to_idx(sband, rx_ev.rate / 100);
 
@@ -6301,6 +6314,8 @@
 		ath11k_wmi_event_scan_start_failed(ar);
 		break;
 	case WMI_SCAN_EVENT_DEQUEUED:
+		__ath11k_mac_scan_finish(ar);
+		break;
 	case WMI_SCAN_EVENT_PREEMPTED:
 	case WMI_SCAN_EVENT_RESTARTED:
 	case WMI_SCAN_EVENT_FOREIGN_CHAN_EXIT:
@@ -6794,6 +6809,8 @@
 		   ev->detector_id, ev->segment_id, ev->timestamp, ev->is_chirp,
 		   ev->freq_offset, ev->sidx);
 
+	rcu_read_lock();
+
 	ar = ath11k_mac_get_ar_by_pdev_id(ab, ev->pdev_id);
 
 	if (!ar) {
@@ -6811,6 +6828,8 @@
 		ieee80211_radar_detected(ar->hw);
 
 exit:
+	rcu_read_unlock();
+
 	kfree(tb);
 }
 
@@ -6840,15 +6859,19 @@
 	ath11k_dbg(ab, ATH11K_DBG_WMI,
 		   "pdev temperature ev temp %d pdev_id %d\n", ev->temp, ev->pdev_id);
 
+	rcu_read_lock();
+
 	ar = ath11k_mac_get_ar_by_pdev_id(ab, ev->pdev_id);
 	if (!ar) {
 		ath11k_warn(ab, "invalid pdev id in pdev temperature ev %d", ev->pdev_id);
-		kfree(tb);
-		return;
+		goto exit;
 	}
 
 	ath11k_thermal_event_temperature(ar, ev->temp);
 
+exit:
+	rcu_read_unlock();
+
 	kfree(tb);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath11k/wmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath11k/wmi.h
@@ -2960,6 +2960,7 @@
 	u32 tlv_header;
 	/* ref wmi_bss_chan_info_req_type */
 	u32 req_type;
+	u32 pdev_id;
 } __packed;
 
 struct wmi_ap_ps_peer_cmd {
@@ -3024,7 +3025,6 @@
 
 #define WLAN_SCAN_MAX_NUM_SSID          10
 #define WLAN_SCAN_MAX_NUM_BSSID         10
-#define WLAN_SCAN_MAX_NUM_CHANNELS      40
 
 #define WLAN_SSID_MAX_LEN 32
 
@@ -3245,7 +3245,7 @@
 	u32 num_bssid;
 	u32 num_ssids;
 	u32 n_probes;
-	u32 chan_list[WLAN_SCAN_MAX_NUM_CHANNELS];
+	u32 *chan_list;
 	u32 notify_scan_events;
 	struct wlan_ssid ssid[WLAN_SCAN_MAX_NUM_SSID];
 	struct wmi_mac_addr bssid_list[WLAN_SCAN_MAX_NUM_BSSID];
@@ -4056,7 +4056,6 @@
 } __packed;
 
 struct wmi_pdev_bss_chan_info_event {
-	u32 pdev_id;
 	u32 freq;	/* Units in MHz */
 	u32 noise_floor;	/* units are dBm */
 	/* rx clear - how often the channel was unused */
@@ -4074,6 +4073,7 @@
 	/*rx_cycle cnt for my bss in 64bits format */
 	u32 rx_bss_cycle_count_low;
 	u32 rx_bss_cycle_count_high;
+	u32 pdev_id;
 } __packed;
 
 #define WMI_VDEV_INSTALL_KEY_COMPL_STATUS_SUCCESS 0
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath5k/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -529,7 +529,7 @@
 		ee->ee_n_piers[mode]++;
 
 		freq2 = (val >> 8) & 0xff;
-		if (!freq2)
+		if (!freq2 || i >= max)
 			break;
 
 		pc[i++].freq = ath5k_eeprom_bin2freq(ee,
@@ -746,6 +746,9 @@
 			}
 		}
 
+		if (idx == AR5K_EEPROM_N_PD_CURVES)
+			goto err_out;
+
 		ee->ee_pd_gains[mode] = 1;
 
 		pd = &chinfo[pier].pd_curves[idx];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath5k/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath5k/pci.c
@@ -46,6 +46,8 @@
 	{ PCI_VDEVICE(ATHEROS, 0x001b) }, /* 5413 Eagle */
 	{ PCI_VDEVICE(ATHEROS, 0x001c) }, /* PCI-E cards */
 	{ PCI_VDEVICE(ATHEROS, 0x001d) }, /* 2417 Nala */
+	{ PCI_VDEVICE(ATHEROS, 0xff16) }, /* Gigaset SX76[23] AR241[34]A */
+	{ PCI_VDEVICE(ATHEROS, 0xff1a) }, /* Arcadyan ARV45XX AR2417 */
 	{ PCI_VDEVICE(ATHEROS, 0xff1b) }, /* AR5BXB63 */
 	{ 0 }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath6kl/bmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath6kl/bmi.c
@@ -246,7 +246,7 @@
 		return -EACCES;
 	}
 
-	size = sizeof(cid) + sizeof(addr) + sizeof(param);
+	size = sizeof(cid) + sizeof(addr) + sizeof(*param);
 	if (size > ar->bmi.max_cmd_size) {
 		WARN_ON(1);
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath6kl/htc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath6kl/htc.h
@@ -153,12 +153,19 @@
  * implementations.
  */
 struct htc_frame_hdr {
-	u8 eid;
-	u8 flags;
+	struct_group_tagged(htc_frame_look_ahead, header,
+		union {
+			struct {
+				u8 eid;
+				u8 flags;
 
-	/* length of data (including trailer) that follows the header */
-	__le16 payld_len;
+				/* length of data (including trailer) that follows the header */
+				__le16 payld_len;
 
+			};
+			u32 word;
+		};
+	);
 	/* end of 4-byte lookahead */
 
 	u8 ctrl[2];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath6kl/htc_mbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath6kl/htc_mbox.c
@@ -2260,19 +2260,16 @@
 static struct htc_packet *htc_wait_for_ctrl_msg(struct htc_target *target)
 {
 	struct htc_packet *packet = NULL;
-	struct htc_frame_hdr *htc_hdr;
-	u32 look_ahead;
+	struct htc_frame_look_ahead look_ahead;
 
-	if (ath6kl_hif_poll_mboxmsg_rx(target->dev, &look_ahead,
+	if (ath6kl_hif_poll_mboxmsg_rx(target->dev, &look_ahead.word,
 				       HTC_TARGET_RESPONSE_TIMEOUT))
 		return NULL;
 
 	ath6kl_dbg(ATH6KL_DBG_HTC,
-		   "htc rx wait ctrl look_ahead 0x%X\n", look_ahead);
+		   "htc rx wait ctrl look_ahead 0x%X\n", look_ahead.word);
 
-	htc_hdr = (struct htc_frame_hdr *)&look_ahead;
-
-	if (htc_hdr->eid != ENDPOINT_0)
+	if (look_ahead.eid != ENDPOINT_0)
 		return NULL;
 
 	packet = htc_get_control_buf(target, false);
@@ -2281,8 +2278,8 @@
 		return NULL;
 
 	packet->info.rx.rx_flags = 0;
-	packet->info.rx.exp_hdr = look_ahead;
-	packet->act_len = le16_to_cpu(htc_hdr->payld_len) + HTC_HDR_LENGTH;
+	packet->info.rx.exp_hdr = look_ahead.word;
+	packet->act_len = le16_to_cpu(look_ahead.payld_len) + HTC_HDR_LENGTH;
 
 	if (packet->act_len > packet->buf_len)
 		goto fail_ctrl_rx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath6kl/htc_pipe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath6kl/htc_pipe.c
@@ -960,8 +960,8 @@
 	 * Thus the possibility of ar->htc_target being NULL
 	 * via ath6kl_recv_complete -> ath6kl_usb_io_comp_work.
 	 */
-	if (WARN_ON_ONCE(!target)) {
-		ath6kl_err("Target not yet initialized\n");
+	if (!target) {
+		ath6kl_dbg(ATH6KL_DBG_HTC, "Target not yet initialized\n");
 		status = -EINVAL;
 		goto free_skb;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath6kl/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath6kl/usb.c
@@ -340,6 +340,11 @@
 				   le16_to_cpu(endpoint->wMaxPacketSize),
 				   endpoint->bInterval);
 		}
+
+		/* Ignore broken descriptors. */
+		if (usb_endpoint_maxp(endpoint) == 0)
+			continue;
+
 		urbcount = 0;
 
 		pipe_num =
@@ -907,7 +912,7 @@
 				 req,
 				 USB_DIR_IN | USB_TYPE_VENDOR |
 				 USB_RECIP_DEVICE, value, index, buf,
-				 size, 2 * HZ);
+				 size, 2000);
 
 	if (ret < 0) {
 		ath6kl_warn("Failed to read usb control message: %d\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/ahb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/ahb.c
@@ -136,8 +136,8 @@
 
 	ah = sc->sc_ah;
 	ath9k_hw_name(ah, hw_name, sizeof(hw_name));
-	wiphy_info(hw->wiphy, "%s mem=0x%lx, irq=%d\n",
-		   hw_name, (unsigned long)mem, irq);
+	wiphy_info(hw->wiphy, "%s mem=0x%p, irq=%d\n",
+		   hw_name, mem, irq);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/antenna.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/antenna.c
@@ -643,7 +643,7 @@
 				conf->main_lna_conf = ATH_ANT_DIV_COMB_LNA1;
 				conf->alt_lna_conf = ATH_ANT_DIV_COMB_LNA1_PLUS_LNA2;
 			} else if (antcomb->rssi_sub >
-				   antcomb->rssi_lna1) {
+				   antcomb->rssi_lna2) {
 				/* set to A-B */
 				conf->main_lna_conf = ATH_ANT_DIV_COMB_LNA1;
 				conf->alt_lna_conf = ATH_ANT_DIV_COMB_LNA1_MINUS_LNA2;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -5615,7 +5615,7 @@
 
 static u8 ar9003_get_eepmisc(struct ath_hw *ah)
 {
-	return ah->eeprom.map4k.baseEepHeader.eepMisc;
+	return ah->eeprom.ar9300_eep.baseEepHeader.opCapFlags.eepMisc;
 }
 
 const struct eeprom_ops eep_ar9300_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/ar9003_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/ar9003_hw.c
@@ -1099,17 +1099,22 @@
 {
 	u32 dma_dbg_chain, dma_dbg_complete;
 	u8 dcu_chain_state, dcu_complete_state;
+	unsigned int dbg_reg, reg_offset;
 	int i;
 
-	for (i = 0; i < NUM_STATUS_READS; i++) {
-		if (queue < 6)
-			dma_dbg_chain = REG_READ(ah, AR_DMADBG_4);
-		else
-			dma_dbg_chain = REG_READ(ah, AR_DMADBG_5);
+	if (queue < 6) {
+		dbg_reg = AR_DMADBG_4;
+		reg_offset = queue * 5;
+	} else {
+		dbg_reg = AR_DMADBG_5;
+		reg_offset = (queue - 6) * 5;
+	}
 
+	for (i = 0; i < NUM_STATUS_READS; i++) {
+		dma_dbg_chain = REG_READ(ah, dbg_reg);
 		dma_dbg_complete = REG_READ(ah, AR_DMADBG_6);
 
-		dcu_chain_state = (dma_dbg_chain >> (5 * queue)) & 0x1f;
+		dcu_chain_state = (dma_dbg_chain >> reg_offset) & 0x1f;
 		dcu_complete_state = dma_dbg_complete & 0x3;
 
 		if ((dcu_chain_state != 0x6) || (dcu_complete_state != 0x1))
@@ -1128,6 +1133,7 @@
 	u8 dcu_chain_state, dcu_complete_state;
 	bool dcu_wait_frdone = false;
 	unsigned long chk_dcu = 0;
+	unsigned int reg_offset;
 	unsigned int i = 0;
 
 	dma_dbg_4 = REG_READ(ah, AR_DMADBG_4);
@@ -1139,12 +1145,15 @@
 		goto exit;
 
 	for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
-		if (i < 6)
+		if (i < 6) {
 			chk_dbg = dma_dbg_4;
-		else
+			reg_offset = i * 5;
+		} else {
 			chk_dbg = dma_dbg_5;
+			reg_offset = (i - 6) * 5;
+		}
 
-		dcu_chain_state = (chk_dbg >> (5 * i)) & 0x1f;
+		dcu_chain_state = (chk_dbg >> reg_offset) & 0x1f;
 		if (dcu_chain_state == 0x6) {
 			dcu_wait_frdone = true;
 			chk_dcu |= BIT(i);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -720,7 +720,7 @@
 #define AR_CH0_TOP2		(AR_SREV_9300(ah) ? 0x1628c : \
 					(AR_SREV_9462(ah) ? 0x16290 : 0x16284))
 #define AR_CH0_TOP2_XPABIASLVL		(AR_SREV_9561(ah) ? 0x1e00 : 0xf000)
-#define AR_CH0_TOP2_XPABIASLVL_S	12
+#define AR_CH0_TOP2_XPABIASLVL_S	(AR_SREV_9561(ah) ? 9 : 12)
 
 #define AR_CH0_XTAL		(AR_SREV_9300(ah) ? 0x16294 : \
 				 ((AR_SREV_9462(ah) || AR_SREV_9565(ah)) ? 0x16298 : \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/debug.c
@@ -1284,7 +1284,7 @@
 			  u32 sset, u8 *data)
 {
 	if (sset == ETH_SS_STATS)
-		memcpy(data, *ath9k_gstrings_stats,
+		memcpy(data, ath9k_gstrings_stats,
 		       sizeof(ath9k_gstrings_stats));
 }
 
@@ -1316,11 +1316,11 @@
 	struct ath_softc *sc = hw->priv;
 	int i = 0;
 
-	data[i++] = (sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_BE)].tx_pkts_all +
+	data[i++] = ((u64)sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_BE)].tx_pkts_all +
 		     sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_BK)].tx_pkts_all +
 		     sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_VI)].tx_pkts_all +
 		     sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_VO)].tx_pkts_all);
-	data[i++] = (sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_BE)].tx_bytes_all +
+	data[i++] = ((u64)sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_BE)].tx_bytes_all +
 		     sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_BK)].tx_bytes_all +
 		     sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_VI)].tx_bytes_all +
 		     sc->debug.stats.txstats[PR_QNUM(IEEE80211_AC_VO)].tx_bytes_all);
@@ -1371,8 +1371,6 @@
 
 	sc->debug.debugfs_phy = debugfs_create_dir("ath9k",
 						   sc->hw->wiphy->debugfsdir);
-	if (!sc->debug.debugfs_phy)
-		return -ENOMEM;
 
 #ifdef CONFIG_ATH_DEBUG
 	debugfs_create_file("debug", 0600, sc->debug.debugfs_phy,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/hif_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/hif_usb.c
@@ -244,11 +244,11 @@
 		ath9k_htc_txcompletion_cb(hif_dev->htc_handle,
 					  skb, txok);
 		if (txok) {
-			TX_STAT_INC(skb_success);
-			TX_STAT_ADD(skb_success_bytes, ln);
+			TX_STAT_INC(hif_dev, skb_success);
+			TX_STAT_ADD(hif_dev, skb_success_bytes, ln);
 		}
 		else
-			TX_STAT_INC(skb_failed);
+			TX_STAT_INC(hif_dev, skb_failed);
 	}
 }
 
@@ -302,7 +302,7 @@
 	hif_dev->tx.tx_buf_cnt++;
 	if (!(hif_dev->tx.flags & HIF_USB_TX_STOP))
 		__hif_usb_tx(hif_dev); /* Check for pending SKBs */
-	TX_STAT_INC(buf_completed);
+	TX_STAT_INC(hif_dev, buf_completed);
 	spin_unlock(&hif_dev->tx.tx_lock);
 }
 
@@ -353,7 +353,7 @@
 			tx_buf->len += tx_buf->offset;
 
 		__skb_queue_tail(&tx_buf->skb_queue, nskb);
-		TX_STAT_INC(skb_queued);
+		TX_STAT_INC(hif_dev, skb_queued);
 	}
 
 	usb_fill_bulk_urb(tx_buf->urb, hif_dev->udev,
@@ -368,11 +368,10 @@
 		__skb_queue_head_init(&tx_buf->skb_queue);
 		list_move_tail(&tx_buf->list, &hif_dev->tx.tx_buf);
 		hif_dev->tx.tx_buf_cnt++;
+	} else {
+		TX_STAT_INC(hif_dev, buf_queued);
 	}
 
-	if (!ret)
-		TX_STAT_INC(buf_queued);
-
 	return ret;
 }
 
@@ -515,7 +514,7 @@
 			ath9k_htc_txcompletion_cb(hif_dev->htc_handle,
 						  skb, false);
 			hif_dev->tx.tx_skb_cnt--;
-			TX_STAT_INC(skb_failed);
+			TX_STAT_INC(hif_dev, skb_failed);
 		}
 	}
 
@@ -535,6 +534,24 @@
 	.send = hif_usb_send,
 };
 
+/* Need to free remain_skb allocated in ath9k_hif_usb_rx_stream
+ * in case ath9k_hif_usb_rx_stream wasn't called next time to
+ * process the buffer and subsequently free it.
+ */
+static void ath9k_hif_usb_free_rx_remain_skb(struct hif_device_usb *hif_dev)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&hif_dev->rx_lock, flags);
+	if (hif_dev->remain_skb) {
+		dev_kfree_skb_any(hif_dev->remain_skb);
+		hif_dev->remain_skb = NULL;
+		hif_dev->rx_remain_len = 0;
+		RX_STAT_INC(hif_dev, skb_dropped);
+	}
+	spin_unlock_irqrestore(&hif_dev->rx_lock, flags);
+}
+
 static void ath9k_hif_usb_rx_stream(struct hif_device_usb *hif_dev,
 				    struct sk_buff *skb)
 {
@@ -562,11 +579,11 @@
 			memcpy(ptr, skb->data, rx_remain_len);
 
 			rx_pkt_len += rx_remain_len;
-			hif_dev->rx_remain_len = 0;
 			skb_put(remain_skb, rx_pkt_len);
 
 			skb_pool[pool_index++] = remain_skb;
-
+			hif_dev->remain_skb = NULL;
+			hif_dev->rx_remain_len = 0;
 		} else {
 			index = rx_remain_len;
 		}
@@ -585,9 +602,21 @@
 		pkt_len = get_unaligned_le16(ptr + index);
 		pkt_tag = get_unaligned_le16(ptr + index + 2);
 
+		/* It is supposed that if we have an invalid pkt_tag or
+		 * pkt_len then the whole input SKB is considered invalid
+		 * and dropped; the associated packets already in skb_pool
+		 * are dropped, too.
+		 */
 		if (pkt_tag != ATH_USB_RX_STREAM_MODE_TAG) {
-			RX_STAT_INC(skb_dropped);
-			return;
+			RX_STAT_INC(hif_dev, skb_dropped);
+			goto invalid_pkt;
+		}
+
+		if (pkt_len > 2 * MAX_RX_BUF_SIZE) {
+			dev_err(&hif_dev->udev->dev,
+				"ath9k_htc: invalid pkt_len (%x)\n", pkt_len);
+			RX_STAT_INC(hif_dev, skb_dropped);
+			goto invalid_pkt;
 		}
 
 		pad_len = 4 - (pkt_len & 0x3);
@@ -599,11 +628,6 @@
 
 		if (index > MAX_RX_BUF_SIZE) {
 			spin_lock(&hif_dev->rx_lock);
-			hif_dev->rx_remain_len = index - MAX_RX_BUF_SIZE;
-			hif_dev->rx_transfer_len =
-				MAX_RX_BUF_SIZE - chk_idx - 4;
-			hif_dev->rx_pad_len = pad_len;
-
 			nskb = __dev_alloc_skb(pkt_len + 32, GFP_ATOMIC);
 			if (!nskb) {
 				dev_err(&hif_dev->udev->dev,
@@ -611,8 +635,14 @@
 				spin_unlock(&hif_dev->rx_lock);
 				goto err;
 			}
+
+			hif_dev->rx_remain_len = index - MAX_RX_BUF_SIZE;
+			hif_dev->rx_transfer_len =
+				MAX_RX_BUF_SIZE - chk_idx - 4;
+			hif_dev->rx_pad_len = pad_len;
+
 			skb_reserve(nskb, 32);
-			RX_STAT_INC(skb_allocated);
+			RX_STAT_INC(hif_dev, skb_allocated);
 
 			memcpy(nskb->data, &(skb->data[chk_idx+4]),
 			       hif_dev->rx_transfer_len);
@@ -633,7 +663,7 @@
 				goto err;
 			}
 			skb_reserve(nskb, 32);
-			RX_STAT_INC(skb_allocated);
+			RX_STAT_INC(hif_dev, skb_allocated);
 
 			memcpy(nskb->data, &(skb->data[chk_idx+4]), pkt_len);
 			skb_put(nskb, pkt_len);
@@ -643,11 +673,18 @@
 
 err:
 	for (i = 0; i < pool_index; i++) {
-		RX_STAT_ADD(skb_completed_bytes, skb_pool[i]->len);
+		RX_STAT_ADD(hif_dev, skb_completed_bytes, skb_pool[i]->len);
 		ath9k_htc_rx_msg(hif_dev->htc_handle, skb_pool[i],
 				 skb_pool[i]->len, USB_WLAN_RX_PIPE);
-		RX_STAT_INC(skb_completed);
+		RX_STAT_INC(hif_dev, skb_completed);
 	}
+	return;
+invalid_pkt:
+	for (i = 0; i < pool_index; i++) {
+		dev_kfree_skb_any(skb_pool[i]);
+		RX_STAT_INC(hif_dev, skb_dropped);
+	}
+	return;
 }
 
 static void ath9k_hif_usb_rx_cb(struct urb *urb)
@@ -681,8 +718,7 @@
 	}
 
 resubmit:
-	skb_reset_tail_pointer(skb);
-	skb_trim(skb, 0);
+	__skb_set_length(skb, 0);
 
 	usb_anchor_urb(urb, &hif_dev->rx_submitted);
 	ret = usb_submit_urb(urb, GFP_ATOMIC);
@@ -702,14 +738,13 @@
 	struct rx_buf *rx_buf = (struct rx_buf *)urb->context;
 	struct hif_device_usb *hif_dev = rx_buf->hif_dev;
 	struct sk_buff *skb = rx_buf->skb;
-	struct sk_buff *nskb;
 	int ret;
 
 	if (!skb)
 		return;
 
 	if (!hif_dev)
-		goto free;
+		goto free_skb;
 
 	switch (urb->status) {
 	case 0:
@@ -718,10 +753,9 @@
 	case -ECONNRESET:
 	case -ENODEV:
 	case -ESHUTDOWN:
-		goto free;
+		goto free_skb;
 	default:
-		skb_reset_tail_pointer(skb);
-		skb_trim(skb, 0);
+		__skb_set_length(skb, 0);
 
 		goto resubmit;
 	}
@@ -729,25 +763,27 @@
 	if (likely(urb->actual_length != 0)) {
 		skb_put(skb, urb->actual_length);
 
-		/* Process the command first */
+		/*
+		 * Process the command first.
+		 * skb is either freed here or passed to be
+		 * managed to another callback function.
+		 */
 		ath9k_htc_rx_msg(hif_dev->htc_handle, skb,
 				 skb->len, USB_REG_IN_PIPE);
 
-
-		nskb = alloc_skb(MAX_REG_IN_BUF_SIZE, GFP_ATOMIC);
-		if (!nskb) {
+		skb = alloc_skb(MAX_REG_IN_BUF_SIZE, GFP_ATOMIC);
+		if (!skb) {
 			dev_err(&hif_dev->udev->dev,
 				"ath9k_htc: REG_IN memory allocation failure\n");
-			urb->context = NULL;
-			return;
+			goto free_rx_buf;
 		}
 
-		rx_buf->skb = nskb;
+		rx_buf->skb = skb;
 
 		usb_fill_int_urb(urb, hif_dev->udev,
 				 usb_rcvintpipe(hif_dev->udev,
 						 USB_REG_IN_PIPE),
-				 nskb->data, MAX_REG_IN_BUF_SIZE,
+				 skb->data, MAX_REG_IN_BUF_SIZE,
 				 ath9k_hif_usb_reg_in_cb, rx_buf, 1);
 	}
 
@@ -756,12 +792,13 @@
 	ret = usb_submit_urb(urb, GFP_ATOMIC);
 	if (ret) {
 		usb_unanchor_urb(urb);
-		goto free;
+		goto free_skb;
 	}
 
 	return;
-free:
+free_skb:
 	kfree_skb(skb);
+free_rx_buf:
 	kfree(rx_buf);
 	urb->context = NULL;
 }
@@ -774,14 +811,10 @@
 	spin_lock_irqsave(&hif_dev->tx.tx_lock, flags);
 	list_for_each_entry_safe(tx_buf, tx_buf_tmp,
 				 &hif_dev->tx.tx_buf, list) {
-		usb_get_urb(tx_buf->urb);
-		spin_unlock_irqrestore(&hif_dev->tx.tx_lock, flags);
-		usb_kill_urb(tx_buf->urb);
 		list_del(&tx_buf->list);
 		usb_free_urb(tx_buf->urb);
 		kfree(tx_buf->buf);
 		kfree(tx_buf);
-		spin_lock_irqsave(&hif_dev->tx.tx_lock, flags);
 	}
 	spin_unlock_irqrestore(&hif_dev->tx.tx_lock, flags);
 
@@ -851,6 +884,7 @@
 static void ath9k_hif_usb_dealloc_rx_urbs(struct hif_device_usb *hif_dev)
 {
 	usb_kill_anchored_urbs(&hif_dev->rx_submitted);
+	ath9k_hif_usb_free_rx_remain_skb(hif_dev);
 }
 
 static int ath9k_hif_usb_alloc_rx_urbs(struct hif_device_usb *hif_dev)
@@ -1323,10 +1357,24 @@
 static int ath9k_hif_usb_probe(struct usb_interface *interface,
 			       const struct usb_device_id *id)
 {
+	struct usb_endpoint_descriptor *bulk_in, *bulk_out, *int_in, *int_out;
 	struct usb_device *udev = interface_to_usbdev(interface);
+	struct usb_host_interface *alt;
 	struct hif_device_usb *hif_dev;
 	int ret = 0;
 
+	/* Verify the expected endpoints are present */
+	alt = interface->cur_altsetting;
+	if (usb_find_common_endpoints(alt, &bulk_in, &bulk_out, &int_in, &int_out) < 0 ||
+	    usb_endpoint_num(bulk_in) != USB_WLAN_RX_PIPE ||
+	    usb_endpoint_num(bulk_out) != USB_WLAN_TX_PIPE ||
+	    usb_endpoint_num(int_in) != USB_REG_IN_PIPE ||
+	    usb_endpoint_num(int_out) != USB_REG_OUT_PIPE) {
+		dev_err(&udev->dev,
+			"ath9k_htc: Device endpoint numbers are not the expected ones\n");
+		return -ENODEV;
+	}
+
 	if (id->driver_info == STORAGE_DEVICE)
 		return send_eject_command(interface);
 
@@ -1393,8 +1441,6 @@
 
 	if (hif_dev->flags & HIF_USB_READY) {
 		ath9k_htc_hw_deinit(hif_dev->htc_handle, unplugged);
-		ath9k_hif_usb_dev_deinit(hif_dev);
-		ath9k_destroy_wmi(hif_dev->htc_handle->drv_priv);
 		ath9k_htc_hw_free(hif_dev->htc_handle);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/htc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/htc.h
@@ -281,6 +281,7 @@
 struct ath9k_htc_rx {
 	struct list_head rxbuf;
 	spinlock_t rxbuflock;
+	bool initialized;
 };
 
 #define ATH9K_HTC_TX_CLEANUP_INTERVAL 50 /* ms */
@@ -325,14 +326,18 @@
 }
 
 #ifdef CONFIG_ATH9K_HTC_DEBUGFS
-
-#define TX_STAT_INC(c) (hif_dev->htc_handle->drv_priv->debug.tx_stats.c++)
-#define TX_STAT_ADD(c, a) (hif_dev->htc_handle->drv_priv->debug.tx_stats.c += a)
-#define RX_STAT_INC(c) (hif_dev->htc_handle->drv_priv->debug.skbrx_stats.c++)
-#define RX_STAT_ADD(c, a) (hif_dev->htc_handle->drv_priv->debug.skbrx_stats.c += a)
-#define CAB_STAT_INC   priv->debug.tx_stats.cab_queued++
-
-#define TX_QSTAT_INC(q) (priv->debug.tx_stats.queue_stats[q]++)
+#define __STAT_SAFE(hif_dev, expr)	do { ((hif_dev)->htc_handle->drv_priv ? (expr) : 0); } while (0)
+#define CAB_STAT_INC(priv)		do { ((priv)->debug.tx_stats.cab_queued++); } while (0)
+#define TX_QSTAT_INC(priv, q)		do { ((priv)->debug.tx_stats.queue_stats[q]++); } while (0)
+
+#define TX_STAT_INC(hif_dev, c) \
+		__STAT_SAFE((hif_dev), (hif_dev)->htc_handle->drv_priv->debug.tx_stats.c++)
+#define TX_STAT_ADD(hif_dev, c, a) \
+		__STAT_SAFE((hif_dev), (hif_dev)->htc_handle->drv_priv->debug.tx_stats.c += a)
+#define RX_STAT_INC(hif_dev, c) \
+		__STAT_SAFE((hif_dev), (hif_dev)->htc_handle->drv_priv->debug.skbrx_stats.c++)
+#define RX_STAT_ADD(hif_dev, c, a) \
+		__STAT_SAFE((hif_dev), (hif_dev)->htc_handle->drv_priv->debug.skbrx_stats.c += a)
 
 void ath9k_htc_err_stat_rx(struct ath9k_htc_priv *priv,
 			   struct ath_rx_status *rs);
@@ -372,13 +377,13 @@
 			    struct ethtool_stats *stats, u64 *data);
 #else
 
-#define TX_STAT_INC(c) do { } while (0)
-#define TX_STAT_ADD(c, a) do { } while (0)
-#define RX_STAT_INC(c) do { } while (0)
-#define RX_STAT_ADD(c, a) do { } while (0)
-#define CAB_STAT_INC   do { } while (0)
+#define TX_STAT_INC(hif_dev, c)		do { } while (0)
+#define TX_STAT_ADD(hif_dev, c, a)	do { } while (0)
+#define RX_STAT_INC(hif_dev, c)		do { } while (0)
+#define RX_STAT_ADD(hif_dev, c, a)	do { } while (0)
 
-#define TX_QSTAT_INC(c) do { } while (0)
+#define CAB_STAT_INC(priv)
+#define TX_QSTAT_INC(priv, c)
 
 static inline void ath9k_htc_err_stat_rx(struct ath9k_htc_priv *priv,
 					 struct ath_rx_status *rs)
@@ -509,6 +514,7 @@
 	unsigned long ps_usecount;
 	bool ps_enabled;
 	bool ps_idle;
+	bool initialized;
 
 #ifdef CONFIG_MAC80211_LEDS
 	enum led_brightness brightness;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/htc_drv_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/htc_drv_debug.c
@@ -428,7 +428,7 @@
 			      u32 sset, u8 *data)
 {
 	if (sset == ETH_SS_STATS)
-		memcpy(data, *ath9k_htc_gstrings_stats,
+		memcpy(data, ath9k_htc_gstrings_stats,
 		       sizeof(ath9k_htc_gstrings_stats));
 }
 
@@ -491,8 +491,6 @@
 
 	priv->debug.debugfs_phy = debugfs_create_dir(KBUILD_MODNAME,
 					     priv->hw->wiphy->debugfsdir);
-	if (!priv->debug.debugfs_phy)
-		return -ENOMEM;
 
 	ath9k_cmn_spectral_init_debug(&priv->spec_priv, priv->debug.debugfs_phy);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/htc_drv_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/htc_drv_init.c
@@ -944,7 +944,6 @@
 	priv->hw = hw;
 	priv->htc = htc_handle;
 	priv->dev = dev;
-	htc_handle->drv_priv = priv;
 	SET_IEEE80211_DEV(hw, priv->dev);
 
 	ret = ath9k_htc_wait_for_target(priv);
@@ -965,6 +964,12 @@
 	if (ret)
 		goto err_init;
 
+	htc_handle->drv_priv = priv;
+
+	/* Allow ath9k_wmi_event_tasklet() to operate. */
+	smp_wmb();
+	priv->initialized = true;
+
 	return 0;
 
 err_init:
@@ -987,6 +992,8 @@
 
 		ath9k_deinit_device(htc_handle->drv_priv);
 		ath9k_stop_wmi(htc_handle->drv_priv);
+		ath9k_hif_usb_dealloc_urbs((struct hif_device_usb *)htc_handle->hif_dev);
+		ath9k_destroy_wmi(htc_handle->drv_priv);
 		ieee80211_free_hw(htc_handle->drv_priv->hw);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/htc_drv_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/htc_drv_txrx.c
@@ -106,20 +106,20 @@
 
 	switch (qnum) {
 	case 0:
-		TX_QSTAT_INC(IEEE80211_AC_VO);
+		TX_QSTAT_INC(priv, IEEE80211_AC_VO);
 		epid = priv->data_vo_ep;
 		break;
 	case 1:
-		TX_QSTAT_INC(IEEE80211_AC_VI);
+		TX_QSTAT_INC(priv, IEEE80211_AC_VI);
 		epid = priv->data_vi_ep;
 		break;
 	case 2:
-		TX_QSTAT_INC(IEEE80211_AC_BE);
+		TX_QSTAT_INC(priv, IEEE80211_AC_BE);
 		epid = priv->data_be_ep;
 		break;
 	case 3:
 	default:
-		TX_QSTAT_INC(IEEE80211_AC_BK);
+		TX_QSTAT_INC(priv, IEEE80211_AC_BK);
 		epid = priv->data_bk_ep;
 		break;
 	}
@@ -328,7 +328,7 @@
 	memcpy(tx_fhdr, (u8 *) &tx_hdr, sizeof(tx_hdr));
 
 	if (is_cab) {
-		CAB_STAT_INC;
+		CAB_STAT_INC(priv);
 		tx_ctl->epid = priv->cab_ep;
 		return;
 	}
@@ -652,9 +652,10 @@
 	struct ath9k_htc_tx_event *tx_pend;
 	int i;
 
-	for (i = 0; i < txs->cnt; i++) {
-		WARN_ON(txs->cnt > HTC_MAX_TX_STATUS);
+	if (WARN_ON_ONCE(txs->cnt > HTC_MAX_TX_STATUS))
+		return;
 
+	for (i = 0; i < txs->cnt; i++) {
 		__txs = &txs->txstatus[i];
 
 		skb = ath9k_htc_tx_get_packet(priv, __txs);
@@ -813,6 +814,7 @@
 	skb_queue_head_init(&priv->tx.data_vi_queue);
 	skb_queue_head_init(&priv->tx.data_vo_queue);
 	skb_queue_head_init(&priv->tx.tx_failed);
+
 	return 0;
 }
 
@@ -1011,6 +1013,14 @@
 		goto rx_next;
 	}
 
+	if (rxstatus->rs_keyix >= ATH_KEYMAX &&
+	    rxstatus->rs_keyix != ATH9K_RXKEYIX_INVALID) {
+		ath_dbg(common, ANY,
+			"Invalid keyix, dropping (keyix: %d)\n",
+			rxstatus->rs_keyix);
+		goto rx_next;
+	}
+
 	/* Get the RX status information */
 
 	memset(rx_status, 0, sizeof(struct ieee80211_rx_status));
@@ -1130,6 +1140,10 @@
 	struct ath9k_htc_rxbuf *rxbuf = NULL, *tmp_buf = NULL;
 	unsigned long flags;
 
+	/* Check if ath9k_rx_init() completed. */
+	if (!data_race(priv->rx.initialized))
+		goto err;
+
 	spin_lock_irqsave(&priv->rx.rxbuflock, flags);
 	list_for_each_entry(tmp_buf, &priv->rx.rxbuf, list) {
 		if (!tmp_buf->in_process) {
@@ -1185,6 +1199,10 @@
 		list_add_tail(&rxbuf->list, &priv->rx.rxbuf);
 	}
 
+	/* Allow ath9k_htc_rxep() to operate. */
+	smp_wmb();
+	priv->rx.initialized = true;
+
 	return 0;
 
 err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/htc_hst.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/htc_hst.c
@@ -30,6 +30,7 @@
 	hdr->endpoint_id = epid;
 	hdr->flags = flags;
 	hdr->payload_len = cpu_to_be16(len);
+	memset(hdr->control, 0, sizeof(hdr->control));
 
 	status = target->hif->send(target->hif_dev, endpoint->ul_pipeid, skb);
 
@@ -113,7 +114,13 @@
 
 	if (svc_rspmsg->status == HTC_SERVICE_SUCCESS) {
 		epid = svc_rspmsg->endpoint_id;
-		if (epid < 0 || epid >= ENDPOINT_MAX)
+
+		/* Check that the received epid for the endpoint to attach
+		 * a new service is valid. ENDPOINT0 can't be used here as it
+		 * is already reserved for HTC_CTRL_RSVD_SVC service and thus
+		 * should not be modified.
+		 */
+		if (epid <= ENDPOINT0 || epid >= ENDPOINT_MAX)
 			return;
 
 		service_id = be16_to_cpu(svc_rspmsg->service_id);
@@ -272,6 +279,10 @@
 	conn_msg->dl_pipeid = endpoint->dl_pipeid;
 	conn_msg->ul_pipeid = endpoint->ul_pipeid;
 
+	/* To prevent infoleak */
+	conn_msg->svc_meta_len = 0;
+	conn_msg->pad = 0;
+
 	ret = htc_issue_send(target, skb, skb->len, 0, ENDPOINT0);
 	if (ret)
 		goto err;
@@ -283,6 +294,9 @@
 		return -ETIMEDOUT;
 	}
 
+	if (target->conn_rsp_epid < 0 || target->conn_rsp_epid >= ENDPOINT_MAX)
+		return -EINVAL;
+
 	*conn_rsp_epid = target->conn_rsp_epid;
 	return 0;
 err:
@@ -359,40 +373,34 @@
 }
 
 static void ath9k_htc_fw_panic_report(struct htc_target *htc_handle,
-				      struct sk_buff *skb)
+				      struct sk_buff *skb, u32 len)
 {
 	uint32_t *pattern = (uint32_t *)skb->data;
 
-	switch (*pattern) {
-	case 0x33221199:
-		{
+	if (*pattern == 0x33221199 && len >= sizeof(struct htc_panic_bad_vaddr)) {
 		struct htc_panic_bad_vaddr *htc_panic;
 		htc_panic = (struct htc_panic_bad_vaddr *) skb->data;
 		dev_err(htc_handle->dev, "ath: firmware panic! "
 			"exccause: 0x%08x; pc: 0x%08x; badvaddr: 0x%08x.\n",
 			htc_panic->exccause, htc_panic->pc,
 			htc_panic->badvaddr);
-		break;
-		}
-	case 0x33221299:
-		{
+		return;
+	}
+	if (*pattern == 0x33221299) {
 		struct htc_panic_bad_epid *htc_panic;
 		htc_panic = (struct htc_panic_bad_epid *) skb->data;
 		dev_err(htc_handle->dev, "ath: firmware panic! "
 			"bad epid: 0x%08x\n", htc_panic->epid);
-		break;
-		}
-	default:
-		dev_err(htc_handle->dev, "ath: unknown panic pattern!\n");
-		break;
+		return;
 	}
+	dev_err(htc_handle->dev, "ath: unknown panic pattern!\n");
 }
 
 /*
  * HTC Messages are handled directly here and the obtained SKB
  * is freed.
  *
- * Service messages (Data, WMI) passed to the corresponding
+ * Service messages (Data, WMI) are passed to the corresponding
  * endpoint RX handlers, which have to free the SKB.
  */
 void ath9k_htc_rx_msg(struct htc_target *htc_handle,
@@ -406,16 +414,26 @@
 	if (!htc_handle || !skb)
 		return;
 
+	/* A valid message requires len >= 8.
+	 *
+	 *   sizeof(struct htc_frame_hdr) == 8
+	 *   sizeof(struct htc_ready_msg) == 8
+	 *   sizeof(struct htc_panic_bad_vaddr) == 16
+	 *   sizeof(struct htc_panic_bad_epid) == 8
+	 */
+	if (unlikely(len < sizeof(struct htc_frame_hdr)))
+		goto invalid;
 	htc_hdr = (struct htc_frame_hdr *) skb->data;
 	epid = htc_hdr->endpoint_id;
 
 	if (epid == 0x99) {
-		ath9k_htc_fw_panic_report(htc_handle, skb);
+		ath9k_htc_fw_panic_report(htc_handle, skb, len);
 		kfree_skb(skb);
 		return;
 	}
 
 	if (epid < 0 || epid >= ENDPOINT_MAX) {
+invalid:
 		if (pipe_id != USB_REG_IN_PIPE)
 			dev_kfree_skb_any(skb);
 		else
@@ -427,21 +445,30 @@
 
 		/* Handle trailer */
 		if (htc_hdr->flags & HTC_FLAGS_RECV_TRAILER) {
-			if (be32_to_cpu(*(__be32 *) skb->data) == 0x00C60000)
+			if (be32_to_cpu(*(__be32 *) skb->data) == 0x00C60000) {
 				/* Move past the Watchdog pattern */
 				htc_hdr = (struct htc_frame_hdr *)(skb->data + 4);
+				len -= 4;
+			}
 		}
 
 		/* Get the message ID */
+		if (unlikely(len < sizeof(struct htc_frame_hdr) + sizeof(__be16)))
+			goto invalid;
 		msg_id = (__be16 *) ((void *) htc_hdr +
 				     sizeof(struct htc_frame_hdr));
 
 		/* Now process HTC messages */
 		switch (be16_to_cpu(*msg_id)) {
 		case HTC_MSG_READY_ID:
+			if (unlikely(len < sizeof(struct htc_ready_msg)))
+				goto invalid;
 			htc_process_target_rdy(htc_handle, htc_hdr);
 			break;
 		case HTC_MSG_CONNECT_SERVICE_RESPONSE_ID:
+			if (unlikely(len < sizeof(struct htc_frame_hdr) +
+				     sizeof(struct htc_conn_svc_rspmsg)))
+				goto invalid;
 			htc_process_conn_rsp(htc_handle, htc_hdr);
 			break;
 		default:
@@ -460,6 +487,8 @@
 		if (endpoint->ep_callbacks.rx)
 			endpoint->ep_callbacks.rx(endpoint->ep_callbacks.priv,
 						  skb, epid);
+		else
+			goto invalid;
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/mac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/mac.h
@@ -113,8 +113,10 @@
 	u8 qid;
 	u16 desc_id;
 	u8 tid;
-	u32 ba_low;
-	u32 ba_high;
+	struct_group(ba,
+		u32 ba_low;
+		u32 ba_high;
+	);
 	u32 evm0;
 	u32 evm1;
 	u32 evm2;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/main.c
@@ -135,8 +135,7 @@
 	if (power_mode != ATH9K_PM_AWAKE) {
 		spin_lock(&common->cc_lock);
 		ath_hw_cycle_counters_update(common);
-		memset(&common->cc_survey, 0, sizeof(common->cc_survey));
-		memset(&common->cc_ani, 0, sizeof(common->cc_ani));
+		memset(&common->cc, 0, sizeof(common->cc));
 		spin_unlock(&common->cc_lock);
 	}
 
@@ -203,7 +202,7 @@
 void ath_restart_work(struct ath_softc *sc)
 {
 	ieee80211_queue_delayed_work(sc->hw, &sc->hw_check_work,
-				     ATH_HW_CHECK_POLL_INT);
+				     msecs_to_jiffies(ATH_HW_CHECK_POLL_INT));
 
 	if (AR_SREV_9340(sc->sc_ah) || AR_SREV_9330(sc->sc_ah))
 		ieee80211_queue_delayed_work(sc->hw, &sc->hw_pll_work,
@@ -533,8 +532,10 @@
 	ath9k_debug_sync_cause(sc, sync_cause);
 	status &= ah->imask;	/* discard unasked-for bits */
 
-	if (test_bit(ATH_OP_HW_RESET, &common->op_flags))
+	if (test_bit(ATH_OP_HW_RESET, &common->op_flags)) {
+		ath9k_hw_kill_interrupts(sc->sc_ah);
 		return IRQ_HANDLED;
+	}
 
 	/*
 	 * If there are no status bits set, then this interrupt was not
@@ -837,7 +838,7 @@
 			continue;
 
 		txinfo = IEEE80211_SKB_CB(bf->bf_mpdu);
-		fi = (struct ath_frame_info *)&txinfo->rate_driver_data[0];
+		fi = (struct ath_frame_info *)&txinfo->status.status_driver_data[0];
 		if (fi->keyix == keyix)
 			return true;
 	}
@@ -848,7 +849,7 @@
 static bool ath9k_txq_has_key(struct ath_softc *sc, u32 keyix)
 {
 	struct ath_hw *ah = sc->sc_ah;
-	int i;
+	int i, j;
 	struct ath_txq *txq;
 	bool key_in_use = false;
 
@@ -866,8 +867,9 @@
 		if (sc->sc_ah->caps.hw_caps & ATH9K_HW_CAP_EDMA) {
 			int idx = txq->txq_tailidx;
 
-			while (!key_in_use &&
-			       !list_empty(&txq->txq_fifo[idx])) {
+			for (j = 0; !key_in_use &&
+			     !list_empty(&txq->txq_fifo[idx]) &&
+			     j < ATH_TXFIFO_DEPTH; j++) {
 				key_in_use = ath9k_txq_list_has_key(
 					&txq->txq_fifo[idx], keyix);
 				INCR(idx, ATH_TXFIFO_DEPTH);
@@ -2236,7 +2238,7 @@
 	}
 
 	ieee80211_queue_delayed_work(hw, &sc->hw_check_work,
-				     ATH_HW_CHECK_POLL_INT);
+				     msecs_to_jiffies(ATH_HW_CHECK_POLL_INT));
 }
 
 static bool ath9k_tx_frames_pending(struct ieee80211_hw *hw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/pci.c
@@ -988,8 +988,8 @@
 	sc->sc_ah->msi_reg = 0;
 
 	ath9k_hw_name(sc->sc_ah, hw_name, sizeof(hw_name));
-	wiphy_info(hw->wiphy, "%s mem=0x%lx, irq=%d\n",
-		   hw_name, (unsigned long)sc->mem, pdev->irq);
+	wiphy_info(hw->wiphy, "%s mem=0x%p, irq=%d\n",
+		   hw_name, sc->mem, pdev->irq);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/wmi.c
@@ -155,6 +155,12 @@
 		}
 		spin_unlock_irqrestore(&wmi->wmi_lock, flags);
 
+		/* Check if ath9k_htc_probe_device() completed. */
+		if (!data_race(priv->initialized)) {
+			kfree_skb(skb);
+			continue;
+		}
+
 		hdr = (struct wmi_cmd_hdr *) skb->data;
 		cmd_id = be16_to_cpu(hdr->command_id);
 		wmi_event = skb_pull(skb, sizeof(struct wmi_cmd_hdr));
@@ -217,6 +223,10 @@
 	if (unlikely(wmi->stopped))
 		goto free_skb;
 
+	/* Validate the obtained SKB. */
+	if (unlikely(skb->len < sizeof(struct wmi_cmd_hdr)))
+		goto free_skb;
+
 	hdr = (struct wmi_cmd_hdr *) skb->data;
 	cmd_id = be16_to_cpu(hdr->command_id);
 
@@ -234,10 +244,10 @@
 		spin_unlock_irqrestore(&wmi->wmi_lock, flags);
 		goto free_skb;
 	}
-	spin_unlock_irqrestore(&wmi->wmi_lock, flags);
 
 	/* WMI command response */
 	ath9k_wmi_rsp_callback(wmi, skb);
+	spin_unlock_irqrestore(&wmi->wmi_lock, flags);
 
 free_skb:
 	kfree_skb(skb);
@@ -275,7 +285,8 @@
 
 static int ath9k_wmi_cmd_issue(struct wmi *wmi,
 			       struct sk_buff *skb,
-			       enum wmi_cmd_id cmd, u16 len)
+			       enum wmi_cmd_id cmd, u16 len,
+			       u8 *rsp_buf, u32 rsp_len)
 {
 	struct wmi_cmd_hdr *hdr;
 	unsigned long flags;
@@ -285,6 +296,11 @@
 	hdr->seq_no = cpu_to_be16(++wmi->tx_seq_id);
 
 	spin_lock_irqsave(&wmi->wmi_lock, flags);
+
+	/* record the rsp buffer and length */
+	wmi->cmd_rsp_buf = rsp_buf;
+	wmi->cmd_rsp_len = rsp_len;
+
 	wmi->last_seq_id = wmi->tx_seq_id;
 	spin_unlock_irqrestore(&wmi->wmi_lock, flags);
 
@@ -300,8 +316,8 @@
 	struct ath_common *common = ath9k_hw_common(ah);
 	u16 headroom = sizeof(struct htc_frame_hdr) +
 		       sizeof(struct wmi_cmd_hdr);
+	unsigned long time_left, flags;
 	struct sk_buff *skb;
-	unsigned long time_left;
 	int ret = 0;
 
 	if (ah->ah_flags & AH_UNPLUGGED)
@@ -325,11 +341,7 @@
 		goto out;
 	}
 
-	/* record the rsp buffer and length */
-	wmi->cmd_rsp_buf = rsp_buf;
-	wmi->cmd_rsp_len = rsp_len;
-
-	ret = ath9k_wmi_cmd_issue(wmi, skb, cmd_id, cmd_len);
+	ret = ath9k_wmi_cmd_issue(wmi, skb, cmd_id, cmd_len, rsp_buf, rsp_len);
 	if (ret)
 		goto out;
 
@@ -337,6 +349,9 @@
 	if (!time_left) {
 		ath_dbg(common, WMI, "Timeout waiting for WMI command: %s\n",
 			wmi_cmd_to_name(cmd_id));
+		spin_lock_irqsave(&wmi->wmi_lock, flags);
+		wmi->last_seq_id = 0;
+		spin_unlock_irqrestore(&wmi->wmi_lock, flags);
 		mutex_unlock(&wmi->op_mutex);
 		return -ETIMEDOUT;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/ath9k/xmit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/ath9k/xmit.c
@@ -141,8 +141,8 @@
 {
 	struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
 	BUILD_BUG_ON(sizeof(struct ath_frame_info) >
-		     sizeof(tx_info->rate_driver_data));
-	return (struct ath_frame_info *) &tx_info->rate_driver_data[0];
+		     sizeof(tx_info->status.status_driver_data));
+	return (struct ath_frame_info *) &tx_info->status.status_driver_data[0];
 }
 
 static void ath_send_bar(struct ath_atx_tid *tid, u16 seqno)
@@ -421,7 +421,7 @@
 	isaggr = bf_isaggr(bf);
 	if (isaggr) {
 		seq_st = ts->ts_seqnum;
-		memcpy(ba, &ts->ba_low, WME_BA_BMP_SIZE >> 3);
+		memcpy(ba, &ts->ba, WME_BA_BMP_SIZE >> 3);
 	}
 
 	while (bf) {
@@ -504,7 +504,7 @@
 	if (isaggr && txok) {
 		if (ts->ts_flags & ATH9K_TX_BA) {
 			seq_st = ts->ts_seqnum;
-			memcpy(ba, &ts->ba_low, WME_BA_BMP_SIZE >> 3);
+			memcpy(ba, &ts->ba, WME_BA_BMP_SIZE >> 3);
 		} else {
 			/*
 			 * AR5416 can become deaf/mute when BA
@@ -2501,6 +2501,16 @@
 	spin_unlock_irqrestore(&sc->tx.txbuflock, flags);
 }
 
+static void ath_clear_tx_status(struct ieee80211_tx_info *tx_info)
+{
+	void *ptr = &tx_info->status;
+
+	memset(ptr + sizeof(tx_info->status.rates), 0,
+	       sizeof(tx_info->status) -
+	       sizeof(tx_info->status.rates) -
+	       sizeof(tx_info->status.status_driver_data));
+}
+
 static void ath_tx_rc_status(struct ath_softc *sc, struct ath_buf *bf,
 			     struct ath_tx_status *ts, int nframes, int nbad,
 			     int txok)
@@ -2512,6 +2522,8 @@
 	struct ath_hw *ah = sc->sc_ah;
 	u8 i, tx_rateindex;
 
+	ath_clear_tx_status(tx_info);
+
 	if (txok)
 		tx_info->status.ack_signal = ts->ts_rssi;
 
@@ -2526,6 +2538,13 @@
 	tx_info->status.ampdu_len = nframes;
 	tx_info->status.ampdu_ack_len = nframes - nbad;
 
+	tx_info->status.rates[tx_rateindex].count = ts->ts_longretry + 1;
+
+	for (i = tx_rateindex + 1; i < hw->max_rates; i++) {
+		tx_info->status.rates[i].count = 0;
+		tx_info->status.rates[i].idx = -1;
+	}
+
 	if ((ts->ts_status & ATH9K_TXERR_FILT) == 0 &&
 	    (tx_info->flags & IEEE80211_TX_CTL_NO_ACK) == 0) {
 		/*
@@ -2547,16 +2566,6 @@
 			tx_info->status.rates[tx_rateindex].count =
 				hw->max_rate_tries;
 	}
-
-	for (i = tx_rateindex + 1; i < hw->max_rates; i++) {
-		tx_info->status.rates[i].count = 0;
-		tx_info->status.rates[i].idx = -1;
-	}
-
-	tx_info->status.rates[tx_rateindex].count = ts->ts_longretry + 1;
-
-	/* we report airtime in ath_tx_count_airtime(), don't report twice */
-	tx_info->status.tx_time = 0;
 }
 
 static void ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/carl9170/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/carl9170/main.c
@@ -1915,7 +1915,7 @@
 		WARN_ON(!(tx_streams >= 1 && tx_streams <=
 			IEEE80211_HT_MCS_TX_MAX_STREAMS));
 
-		tx_params = (tx_streams - 1) <<
+		tx_params |= (tx_streams - 1) <<
 			    IEEE80211_HT_MCS_TX_MAX_STREAMS_SHIFT;
 
 		carl9170_band_2GHz.ht_cap.mcs.tx_params |= tx_params;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/carl9170/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/carl9170/tx.c
@@ -1558,6 +1558,9 @@
 					goto out;
 			}
 		} while (ar->beacon_enabled && i--);
+
+		/* no entry found in list */
+		return NULL;
 	}
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/carl9170/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/carl9170/usb.c
@@ -1069,6 +1069,38 @@
 			ar->usb_ep_cmd_is_bulk = true;
 	}
 
+	/* Verify that all expected endpoints are present */
+	if (ar->usb_ep_cmd_is_bulk) {
+		u8 bulk_ep_addr[] = {
+			AR9170_USB_EP_RX | USB_DIR_IN,
+			AR9170_USB_EP_TX | USB_DIR_OUT,
+			AR9170_USB_EP_CMD | USB_DIR_OUT,
+			0};
+		u8 int_ep_addr[] = {
+			AR9170_USB_EP_IRQ | USB_DIR_IN,
+			0};
+		if (!usb_check_bulk_endpoints(intf, bulk_ep_addr) ||
+		    !usb_check_int_endpoints(intf, int_ep_addr))
+			err = -ENODEV;
+	} else {
+		u8 bulk_ep_addr[] = {
+			AR9170_USB_EP_RX | USB_DIR_IN,
+			AR9170_USB_EP_TX | USB_DIR_OUT,
+			0};
+		u8 int_ep_addr[] = {
+			AR9170_USB_EP_IRQ | USB_DIR_IN,
+			AR9170_USB_EP_CMD | USB_DIR_OUT,
+			0};
+		if (!usb_check_bulk_endpoints(intf, bulk_ep_addr) ||
+		    !usb_check_int_endpoints(intf, int_ep_addr))
+			err = -ENODEV;
+	}
+
+	if (err) {
+		carl9170_free(ar);
+		return err;
+	}
+
 	usb_set_intfdata(intf, ar);
 	SET_IEEE80211_DEV(ar->hw, &intf->dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/dfs_pattern_detector.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/dfs_pattern_detector.c
@@ -183,10 +183,12 @@
 	if (cd == NULL)
 		return;
 	list_del(&cd->head);
-	for (i = 0; i < dpd->num_radar_types; i++) {
-		struct pri_detector *de = cd->detectors[i];
-		if (de != NULL)
-			de->exit(de);
+	if (cd->detectors) {
+		for (i = 0; i < dpd->num_radar_types; i++) {
+			struct pri_detector *de = cd->detectors[i];
+			if (de != NULL)
+				de->exit(de);
+		}
 	}
 	kfree(cd->detectors);
 	kfree(cd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/key.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/key.c
@@ -503,7 +503,7 @@
 
 	hk.kv_len = key->keylen;
 	if (key->keylen)
-		memcpy(hk.kv_val, key->key, key->keylen);
+		memcpy(&hk.kv_values, key->key, key->keylen);
 
 	if (!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) {
 		switch (vif->type) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/regd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/regd.c
@@ -667,14 +667,14 @@
 
 /*
  * Some users have reported their EEPROM programmed with
- * 0x8000 or 0x0 set, this is not a supported regulatory
- * domain but since we have more than one user with it we
- * need a solution for them. We default to 0x64, which is
- * the default Atheros world regulatory domain.
+ * 0x8000 set, this is not a supported regulatory domain
+ * but since we have more than one user with it we need
+ * a solution for them. We default to 0x64, which is the
+ * default Atheros world regulatory domain.
  */
 static void ath_regd_sanitize(struct ath_regulatory *reg)
 {
-	if (reg->current_rd != COUNTRY_ERD_FLAG && reg->current_rd != 0)
+	if (reg->current_rd != COUNTRY_ERD_FLAG)
 		return;
 	printk(KERN_DEBUG "ath: EEPROM regdomain sanitized\n");
 	reg->current_rd = 0x64;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/dxe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/dxe.c
@@ -272,6 +272,21 @@
 	return 0;
 }
 
+static void wcn36xx_dxe_disable_ch_int(struct wcn36xx *wcn, u16 wcn_ch)
+{
+	int reg_data = 0;
+
+	wcn36xx_dxe_read_register(wcn,
+				  WCN36XX_DXE_INT_MASK_REG,
+				  &reg_data);
+
+	reg_data &= ~wcn_ch;
+
+	wcn36xx_dxe_write_register(wcn,
+				   WCN36XX_DXE_INT_MASK_REG,
+				   (int)reg_data);
+}
+
 static int wcn36xx_dxe_fill_skb(struct device *dev,
 				struct wcn36xx_dxe_ctl *ctl,
 				gfp_t gfp)
@@ -403,8 +418,21 @@
 			dma_unmap_single(wcn->dev, ctl->desc->src_addr_l,
 					 ctl->skb->len, DMA_TO_DEVICE);
 			info = IEEE80211_SKB_CB(ctl->skb);
-			if (!(info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)) {
-				/* Keep frame until TX status comes */
+			if (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS) {
+				if (info->flags & IEEE80211_TX_CTL_NO_ACK) {
+					info->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
+					ieee80211_tx_status_irqsafe(wcn->hw, ctl->skb);
+				} else {
+					/* Wait for the TX ack indication or timeout... */
+					spin_lock(&wcn->dxe_lock);
+					if (WARN_ON(wcn->tx_ack_skb))
+						ieee80211_free_txskb(wcn->hw, wcn->tx_ack_skb);
+					wcn->tx_ack_skb = ctl->skb; /* Tracking ref */
+					mod_timer(&wcn->tx_ack_timer, jiffies + HZ / 10);
+					spin_unlock(&wcn->dxe_lock);
+				}
+				/* do not free, ownership transferred to mac80211 status cb */
+			} else {
 				ieee80211_free_txskb(wcn->hw, ctl->skb);
 			}
 
@@ -426,7 +454,6 @@
 {
 	struct wcn36xx *wcn = (struct wcn36xx *)dev;
 	int int_src, int_reason;
-	bool transmitted = false;
 
 	wcn36xx_dxe_read_register(wcn, WCN36XX_DXE_INT_SRC_RAW_REG, &int_src);
 
@@ -466,7 +493,6 @@
 		if (int_reason & (WCN36XX_CH_STAT_INT_DONE_MASK |
 				  WCN36XX_CH_STAT_INT_ED_MASK)) {
 			reap_tx_dxes(wcn, &wcn->dxe_tx_h_ch);
-			transmitted = true;
 		}
 	}
 
@@ -479,7 +505,6 @@
 					   WCN36XX_DXE_0_INT_CLR,
 					   WCN36XX_INT_MASK_CHAN_TX_L);
 
-
 		if (int_reason & WCN36XX_CH_STAT_INT_ERR_MASK ) {
 			wcn36xx_dxe_write_register(wcn,
 						   WCN36XX_DXE_0_INT_ERR_CLR,
@@ -507,25 +532,8 @@
 		if (int_reason & (WCN36XX_CH_STAT_INT_DONE_MASK |
 				  WCN36XX_CH_STAT_INT_ED_MASK)) {
 			reap_tx_dxes(wcn, &wcn->dxe_tx_l_ch);
-			transmitted = true;
-		}
-	}
-
-	spin_lock(&wcn->dxe_lock);
-	if (wcn->tx_ack_skb && transmitted) {
-		struct ieee80211_tx_info *info = IEEE80211_SKB_CB(wcn->tx_ack_skb);
-
-		/* TX complete, no need to wait for 802.11 ack indication */
-		if (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS &&
-		    info->flags & IEEE80211_TX_CTL_NO_ACK) {
-			info->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
-			del_timer(&wcn->tx_ack_timer);
-			ieee80211_tx_status_irqsafe(wcn->hw, wcn->tx_ack_skb);
-			wcn->tx_ack_skb = NULL;
-			ieee80211_wake_queues(wcn->hw);
 		}
 	}
-	spin_unlock(&wcn->dxe_lock);
 
 	return IRQ_HANDLED;
 }
@@ -613,6 +621,10 @@
 	dxe = ctl->desc;
 
 	while (!(READ_ONCE(dxe->ctrl) & WCN36xx_DXE_CTRL_VLD)) {
+		/* do not read until we own DMA descriptor */
+		dma_rmb();
+
+		/* read/modify DMA descriptor */
 		skb = ctl->skb;
 		dma_addr = dxe->dst_addr_l;
 		ret = wcn36xx_dxe_fill_skb(wcn->dev, ctl, GFP_ATOMIC);
@@ -623,9 +635,15 @@
 			dma_unmap_single(wcn->dev, dma_addr, WCN36XX_PKT_SIZE,
 					DMA_FROM_DEVICE);
 			wcn36xx_rx_skb(wcn, skb);
-		} /* else keep old skb not submitted and use it for rx DMA */
+		}
+		/* else keep old skb not submitted and reuse it for rx DMA
+		 * (dropping the packet that it contained)
+		 */
 
+		/* flush descriptor changes before re-marking as valid */
+		dma_wmb();
 		dxe->ctrl = ctrl;
+
 		ctl = ctl->next;
 		dxe = ctl->desc;
 	}
@@ -866,7 +884,6 @@
 		WCN36XX_DXE_WQ_TX_L);
 
 	wcn36xx_dxe_read_register(wcn, WCN36XX_DXE_REG_CH_EN, &reg_data);
-	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_TX_L);
 
 	/***************************************/
 	/* Init descriptors for TX HIGH channel */
@@ -890,9 +907,6 @@
 
 	wcn36xx_dxe_read_register(wcn, WCN36XX_DXE_REG_CH_EN, &reg_data);
 
-	/* Enable channel interrupts */
-	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_TX_H);
-
 	/***************************************/
 	/* Init descriptors for RX LOW channel */
 	/***************************************/
@@ -902,7 +916,6 @@
 		goto out_err_rxl_ch;
 	}
 
-
 	/* For RX we need to preallocated buffers */
 	wcn36xx_dxe_ch_alloc_skb(wcn, &wcn->dxe_rx_l_ch);
 
@@ -925,9 +938,6 @@
 		WCN36XX_DXE_REG_CTL_RX_L,
 		WCN36XX_DXE_CH_DEFAULT_CTL_RX_L);
 
-	/* Enable channel interrupts */
-	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_RX_L);
-
 	/***************************************/
 	/* Init descriptors for RX HIGH channel */
 	/***************************************/
@@ -959,15 +969,18 @@
 		WCN36XX_DXE_REG_CTL_RX_H,
 		WCN36XX_DXE_CH_DEFAULT_CTL_RX_H);
 
-	/* Enable channel interrupts */
-	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_RX_H);
-
 	ret = wcn36xx_dxe_request_irqs(wcn);
 	if (ret < 0)
 		goto out_err_irq;
 
 	timer_setup(&wcn->tx_ack_timer, wcn36xx_dxe_tx_timer, 0);
 
+	/* Enable channel interrupts */
+	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_TX_L);
+	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_TX_H);
+	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_RX_L);
+	wcn36xx_dxe_enable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_RX_H);
+
 	return 0;
 
 out_err_irq:
@@ -984,6 +997,14 @@
 
 void wcn36xx_dxe_deinit(struct wcn36xx *wcn)
 {
+	int reg_data = 0;
+
+	/* Disable channel interrupts */
+	wcn36xx_dxe_disable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_RX_H);
+	wcn36xx_dxe_disable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_RX_L);
+	wcn36xx_dxe_disable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_TX_H);
+	wcn36xx_dxe_disable_ch_int(wcn, WCN36XX_INT_MASK_CHAN_TX_L);
+
 	free_irq(wcn->tx_irq, wcn);
 	free_irq(wcn->rx_irq, wcn);
 	del_timer(&wcn->tx_ack_timer);
@@ -993,6 +1014,15 @@
 		wcn->tx_ack_skb = NULL;
 	}
 
+	/* Put the DXE block into reset before freeing memory */
+	reg_data = WCN36XX_DXE_REG_RESET;
+	wcn36xx_dxe_write_register(wcn, WCN36XX_DXE_REG_CSR_RESET, reg_data);
+
 	wcn36xx_dxe_ch_free_skbs(wcn, &wcn->dxe_rx_l_ch);
 	wcn36xx_dxe_ch_free_skbs(wcn, &wcn->dxe_rx_h_ch);
+
+	wcn36xx_dxe_deinit_descs(wcn->dev, &wcn->dxe_tx_l_ch);
+	wcn36xx_dxe_deinit_descs(wcn->dev, &wcn->dxe_tx_h_ch);
+	wcn36xx_dxe_deinit_descs(wcn->dev, &wcn->dxe_rx_l_ch);
+	wcn36xx_dxe_deinit_descs(wcn->dev, &wcn->dxe_rx_h_ch);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/hal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/hal.h
@@ -359,6 +359,8 @@
 	WCN36XX_HAL_START_SCAN_OFFLOAD_RSP = 205,
 	WCN36XX_HAL_STOP_SCAN_OFFLOAD_REQ = 206,
 	WCN36XX_HAL_STOP_SCAN_OFFLOAD_RSP = 207,
+	WCN36XX_HAL_UPDATE_CHANNEL_LIST_REQ = 208,
+	WCN36XX_HAL_UPDATE_CHANNEL_LIST_RSP = 209,
 	WCN36XX_HAL_SCAN_OFFLOAD_IND = 210,
 
 	WCN36XX_HAL_AVOID_FREQ_RANGE_IND = 233,
@@ -1353,6 +1355,36 @@
 	u32 status;
 } __packed;
 
+#define WCN36XX_HAL_CHAN_REG1_MIN_PWR_MASK  0x000000ff
+#define WCN36XX_HAL_CHAN_REG1_MAX_PWR_MASK  0x0000ff00
+#define WCN36XX_HAL_CHAN_REG1_REG_PWR_MASK  0x00ff0000
+#define WCN36XX_HAL_CHAN_REG1_CLASS_ID_MASK 0xff000000
+#define WCN36XX_HAL_CHAN_REG2_ANT_GAIN_MASK 0x000000ff
+#define WCN36XX_HAL_CHAN_INFO_FLAG_PASSIVE  BIT(7)
+#define WCN36XX_HAL_CHAN_INFO_FLAG_DFS      BIT(10)
+#define WCN36XX_HAL_CHAN_INFO_FLAG_HT       BIT(11)
+#define WCN36XX_HAL_CHAN_INFO_FLAG_VHT      BIT(12)
+#define WCN36XX_HAL_CHAN_INFO_PHY_11A       0
+#define WCN36XX_HAL_CHAN_INFO_PHY_11BG      1
+#define WCN36XX_HAL_DEFAULT_ANT_GAIN        6
+#define WCN36XX_HAL_DEFAULT_MIN_POWER       6
+
+struct wcn36xx_hal_channel_param {
+	u32 mhz;
+	u32 band_center_freq1;
+	u32 band_center_freq2;
+	u32 channel_info;
+	u32 reg_info_1;
+	u32 reg_info_2;
+} __packed;
+
+struct wcn36xx_hal_update_channel_list_req_msg {
+	struct wcn36xx_hal_msg_header header;
+
+	u8 num_channel;
+	struct wcn36xx_hal_channel_param channels[80];
+} __packed;
+
 enum wcn36xx_hal_rate_index {
 	HW_RATE_INDEX_1MBPS	= 0x82,
 	HW_RATE_INDEX_2MBPS	= 0x84,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/main.c
@@ -135,7 +135,9 @@
 		.cap =	IEEE80211_HT_CAP_GRN_FLD |
 			IEEE80211_HT_CAP_SGI_20 |
 			IEEE80211_HT_CAP_DSSSCCK40 |
-			IEEE80211_HT_CAP_LSIG_TXOP_PROT,
+			IEEE80211_HT_CAP_LSIG_TXOP_PROT |
+			IEEE80211_HT_CAP_SGI_40 |
+			IEEE80211_HT_CAP_SUP_WIDTH_20_40,
 		.ht_supported = true,
 		.ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K,
 		.ampdu_density = IEEE80211_HT_MPDU_DENSITY_16,
@@ -398,6 +400,7 @@
 static int wcn36xx_config(struct ieee80211_hw *hw, u32 changed)
 {
 	struct wcn36xx *wcn = hw->priv;
+	int ret;
 
 	wcn36xx_dbg(WCN36XX_DBG_MAC, "mac config changed 0x%08x\n", changed);
 
@@ -413,17 +416,31 @@
 			 * want to receive/transmit regular data packets, then
 			 * simply stop the scan session and exit PS mode.
 			 */
-			wcn36xx_smd_finish_scan(wcn, HAL_SYS_MODE_SCAN,
-						wcn->sw_scan_vif);
-			wcn->sw_scan_channel = 0;
+			if (wcn->sw_scan_channel)
+				wcn36xx_smd_end_scan(wcn, wcn->sw_scan_channel);
+			if (wcn->sw_scan_init) {
+				wcn36xx_smd_finish_scan(wcn, HAL_SYS_MODE_SCAN,
+							wcn->sw_scan_vif);
+			}
 		} else if (wcn->sw_scan) {
 			/* A scan is ongoing, do not change the operating
 			 * channel, but start a scan session on the channel.
 			 */
-			wcn36xx_smd_init_scan(wcn, HAL_SYS_MODE_SCAN,
-					      wcn->sw_scan_vif);
+			if (wcn->sw_scan_channel)
+				wcn36xx_smd_end_scan(wcn, wcn->sw_scan_channel);
+			if (!wcn->sw_scan_init) {
+				/* This can fail if we are unable to notify the
+				 * operating channel.
+				 */
+				ret = wcn36xx_smd_init_scan(wcn,
+							    HAL_SYS_MODE_SCAN,
+							    wcn->sw_scan_vif);
+				if (ret) {
+					mutex_unlock(&wcn->conf_mutex);
+					return -EIO;
+				}
+			}
 			wcn36xx_smd_start_scan(wcn, ch);
-			wcn->sw_scan_channel = ch;
 		} else {
 			wcn36xx_change_opchannel(wcn, ch);
 		}
@@ -569,12 +586,14 @@
 		if (IEEE80211_KEY_FLAG_PAIRWISE & key_conf->flags) {
 			sta_priv->is_data_encrypted = true;
 			/* Reconfigure bss with encrypt_type */
-			if (NL80211_IFTYPE_STATION == vif->type)
+			if (NL80211_IFTYPE_STATION == vif->type) {
 				wcn36xx_smd_config_bss(wcn,
 						       vif,
 						       sta,
 						       sta->addr,
 						       true);
+				wcn36xx_smd_config_sta(wcn, vif, sta);
+			}
 
 			wcn36xx_smd_set_stakey(wcn,
 				vif_priv->encrypt_type,
@@ -604,15 +623,6 @@
 				}
 			}
 		}
-		/* FIXME: Only enable bmps support when encryption is enabled.
-		 * For any reasons, when connected to open/no-security BSS,
-		 * the wcn36xx controller in bmps mode does not forward
-		 * 'wake-up' beacons despite AP sends DTIM with station AID.
-		 * It could be due to a firmware issue or to the way driver
-		 * configure the station.
-		 */
-		if (vif->type == NL80211_IFTYPE_STATION)
-			vif_priv->allow_bmps = true;
 		break;
 	case DISABLE_KEY:
 		if (!(IEEE80211_KEY_FLAG_PAIRWISE & key_conf->flags)) {
@@ -676,6 +686,7 @@
 
 	mutex_unlock(&wcn->scan_lock);
 
+	wcn36xx_smd_update_channel_list(wcn, &hw_req->req);
 	return wcn36xx_smd_start_hw_scan(wcn, vif, &hw_req->req);
 }
 
@@ -717,7 +728,12 @@
 	struct wcn36xx *wcn = hw->priv;
 
 	/* ensure that any scan session is finished */
-	wcn36xx_smd_finish_scan(wcn, HAL_SYS_MODE_SCAN, wcn->sw_scan_vif);
+	if (wcn->sw_scan_channel)
+		wcn36xx_smd_end_scan(wcn, wcn->sw_scan_channel);
+	if (wcn->sw_scan_init) {
+		wcn36xx_smd_finish_scan(wcn, HAL_SYS_MODE_SCAN,
+					wcn->sw_scan_vif);
+	}
 	wcn->sw_scan = false;
 	wcn->sw_scan_opchannel = 0;
 }
@@ -913,7 +929,6 @@
 				    vif->addr,
 				    bss_conf->aid);
 			vif_priv->sta_assoc = false;
-			vif_priv->allow_bmps = false;
 			wcn36xx_smd_set_link_st(wcn,
 						bss_conf->bssid,
 						vif->addr,
@@ -1123,6 +1138,13 @@
 			goto out;
 		ret = wcn36xx_smd_wlan_host_suspend_ind(wcn);
 	}
+
+	/* Disable IRQ, we don't want to handle any packet before mac80211 is
+	 * resumed and ready to receive packets.
+	 */
+	disable_irq(wcn->tx_irq);
+	disable_irq(wcn->rx_irq);
+
 out:
 	mutex_unlock(&wcn->conf_mutex);
 	return ret;
@@ -1145,6 +1167,10 @@
 		wcn36xx_smd_ipv6_ns_offload(wcn, vif, false);
 		wcn36xx_smd_arp_offload(wcn, vif, false);
 	}
+
+	enable_irq(wcn->tx_irq);
+	enable_irq(wcn->rx_irq);
+
 	mutex_unlock(&wcn->conf_mutex);
 
 	return 0;
@@ -1338,7 +1364,6 @@
 	ieee80211_hw_set(wcn->hw, HAS_RATE_CONTROL);
 	ieee80211_hw_set(wcn->hw, SINGLE_SCAN_ON_ALL_BANDS);
 	ieee80211_hw_set(wcn->hw, REPORTS_TX_ACK_STATUS);
-	ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR);
 
 	wcn->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
 		BIT(NL80211_IFTYPE_AP) |
@@ -1449,6 +1474,9 @@
 	if (iris_node) {
 		if (of_device_is_compatible(iris_node, "qcom,wcn3620"))
 			wcn->rf_id = RF_IRIS_WCN3620;
+		if (of_device_is_compatible(iris_node, "qcom,wcn3660") ||
+		    of_device_is_compatible(iris_node, "qcom,wcn3660b"))
+			wcn->rf_id = RF_IRIS_WCN3660;
 		if (of_device_is_compatible(iris_node, "qcom,wcn3680"))
 			wcn->rf_id = RF_IRIS_WCN3680;
 		of_node_put(iris_node);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/pmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/pmc.c
@@ -23,10 +23,7 @@
 {
 	int ret = 0;
 	struct wcn36xx_vif *vif_priv = wcn36xx_vif_to_priv(vif);
-
-	if (!vif_priv->allow_bmps)
-		return -ENOTSUPP;
-
+	/* TODO: Make sure the TX chain clean */
 	ret = wcn36xx_smd_enter_bmps(wcn, vif);
 	if (!ret) {
 		wcn36xx_dbg(WCN36XX_DBG_PMC, "Entered BMPS\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/smd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/smd.c
@@ -16,6 +16,7 @@
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
+#include <linux/bitfield.h>
 #include <linux/etherdevice.h>
 #include <linux/firmware.h>
 #include <linux/bitops.h>
@@ -720,6 +721,7 @@
 		wcn36xx_err("hal_init_scan response failed err=%d\n", ret);
 		goto out;
 	}
+	wcn->sw_scan_init = true;
 out:
 	mutex_unlock(&wcn->hal_mutex);
 	return ret;
@@ -750,6 +752,7 @@
 		wcn36xx_err("hal_start_scan response failed err=%d\n", ret);
 		goto out;
 	}
+	wcn->sw_scan_channel = scan_channel;
 out:
 	mutex_unlock(&wcn->hal_mutex);
 	return ret;
@@ -780,6 +783,7 @@
 		wcn36xx_err("hal_end_scan response failed err=%d\n", ret);
 		goto out;
 	}
+	wcn->sw_scan_channel = 0;
 out:
 	mutex_unlock(&wcn->hal_mutex);
 	return ret;
@@ -821,6 +825,7 @@
 		wcn36xx_err("hal_finish_scan response failed err=%d\n", ret);
 		goto out;
 	}
+	wcn->sw_scan_init = false;
 out:
 	mutex_unlock(&wcn->hal_mutex);
 	return ret;
@@ -927,6 +932,86 @@
 	return ret;
 }
 
+int wcn36xx_smd_update_channel_list(struct wcn36xx *wcn, struct cfg80211_scan_request *req)
+{
+	struct wcn36xx_hal_update_channel_list_req_msg *msg_body;
+	int ret, i;
+
+	msg_body = kzalloc(sizeof(*msg_body), GFP_KERNEL);
+	if (!msg_body)
+		return -ENOMEM;
+
+	INIT_HAL_MSG((*msg_body), WCN36XX_HAL_UPDATE_CHANNEL_LIST_REQ);
+
+	msg_body->num_channel = min_t(u8, req->n_channels, ARRAY_SIZE(msg_body->channels));
+	for (i = 0; i < msg_body->num_channel; i++) {
+		struct wcn36xx_hal_channel_param *param = &msg_body->channels[i];
+		u32 min_power = WCN36XX_HAL_DEFAULT_MIN_POWER;
+		u32 ant_gain = WCN36XX_HAL_DEFAULT_ANT_GAIN;
+
+		param->mhz = req->channels[i]->center_freq;
+		param->band_center_freq1 = req->channels[i]->center_freq;
+		param->band_center_freq2 = 0;
+
+		if (req->channels[i]->flags & IEEE80211_CHAN_NO_IR)
+			param->channel_info |= WCN36XX_HAL_CHAN_INFO_FLAG_PASSIVE;
+
+		if (req->channels[i]->flags & IEEE80211_CHAN_RADAR)
+			param->channel_info |= WCN36XX_HAL_CHAN_INFO_FLAG_DFS;
+
+		if (req->channels[i]->band == NL80211_BAND_5GHZ) {
+			param->channel_info |= WCN36XX_HAL_CHAN_INFO_FLAG_HT;
+			param->channel_info |= WCN36XX_HAL_CHAN_INFO_FLAG_VHT;
+			param->channel_info |= WCN36XX_HAL_CHAN_INFO_PHY_11A;
+		} else {
+			param->channel_info |= WCN36XX_HAL_CHAN_INFO_PHY_11BG;
+		}
+
+		if (min_power > req->channels[i]->max_power)
+			min_power = req->channels[i]->max_power;
+
+		if (req->channels[i]->max_antenna_gain)
+			ant_gain = req->channels[i]->max_antenna_gain;
+
+		u32p_replace_bits(&param->reg_info_1, min_power,
+				  WCN36XX_HAL_CHAN_REG1_MIN_PWR_MASK);
+		u32p_replace_bits(&param->reg_info_1, req->channels[i]->max_power,
+				  WCN36XX_HAL_CHAN_REG1_MAX_PWR_MASK);
+		u32p_replace_bits(&param->reg_info_1, req->channels[i]->max_reg_power,
+				  WCN36XX_HAL_CHAN_REG1_REG_PWR_MASK);
+		u32p_replace_bits(&param->reg_info_1, 0,
+				  WCN36XX_HAL_CHAN_REG1_CLASS_ID_MASK);
+		u32p_replace_bits(&param->reg_info_2, ant_gain,
+				  WCN36XX_HAL_CHAN_REG2_ANT_GAIN_MASK);
+
+		wcn36xx_dbg(WCN36XX_DBG_HAL,
+			    "%s: freq=%u, channel_info=%08x, reg_info1=%08x, reg_info2=%08x\n",
+			    __func__, param->mhz, param->channel_info, param->reg_info_1,
+			    param->reg_info_2);
+	}
+
+	mutex_lock(&wcn->hal_mutex);
+
+	PREPARE_HAL_BUF(wcn->hal_buf, (*msg_body));
+
+	ret = wcn36xx_smd_send_and_wait(wcn, msg_body->header.len);
+	if (ret) {
+		wcn36xx_err("Sending hal_update_channel_list failed\n");
+		goto out;
+	}
+
+	ret = wcn36xx_smd_rsp_status_check(wcn->hal_buf, wcn->hal_rsp_len);
+	if (ret) {
+		wcn36xx_err("hal_update_channel_list response failed err=%d\n", ret);
+		goto out;
+	}
+
+out:
+	kfree(msg_body);
+	mutex_unlock(&wcn->hal_mutex);
+	return ret;
+}
+
 static int wcn36xx_smd_switch_channel_rsp(void *buf, size_t len)
 {
 	struct wcn36xx_hal_switch_channel_rsp_msg *rsp;
@@ -2594,7 +2679,7 @@
 			wcn36xx_dbg(WCN36XX_DBG_HAL, "beacon missed bss_index %d\n",
 				    tmp->bss_index);
 			vif = wcn36xx_priv_to_vif(tmp);
-			ieee80211_connection_loss(vif);
+			ieee80211_beacon_loss(vif);
 		}
 		return 0;
 	}
@@ -2609,7 +2694,7 @@
 			wcn36xx_dbg(WCN36XX_DBG_HAL, "beacon missed bss_index %d\n",
 				    rsp->bss_index);
 			vif = wcn36xx_priv_to_vif(tmp);
-			ieee80211_connection_loss(vif);
+			ieee80211_beacon_loss(vif);
 			return 0;
 		}
 	}
@@ -2623,30 +2708,52 @@
 					      size_t len)
 {
 	struct wcn36xx_hal_delete_sta_context_ind_msg *rsp = buf;
-	struct wcn36xx_vif *tmp;
+	struct wcn36xx_vif *vif_priv;
+	struct ieee80211_vif *vif;
+	struct ieee80211_bss_conf *bss_conf;
 	struct ieee80211_sta *sta;
+	bool found = false;
 
 	if (len != sizeof(*rsp)) {
 		wcn36xx_warn("Corrupted delete sta indication\n");
 		return -EIO;
 	}
 
-	wcn36xx_dbg(WCN36XX_DBG_HAL, "delete station indication %pM index %d\n",
-		    rsp->addr2, rsp->sta_id);
+	wcn36xx_dbg(WCN36XX_DBG_HAL,
+		    "delete station indication %pM index %d reason %d\n",
+		    rsp->addr2, rsp->sta_id, rsp->reason_code);
 
-	list_for_each_entry(tmp, &wcn->vif_list, list) {
+	list_for_each_entry(vif_priv, &wcn->vif_list, list) {
 		rcu_read_lock();
-		sta = ieee80211_find_sta(wcn36xx_priv_to_vif(tmp), rsp->addr2);
-		if (sta)
-			ieee80211_report_low_ack(sta, 0);
+		vif = wcn36xx_priv_to_vif(vif_priv);
+
+		if (vif->type == NL80211_IFTYPE_STATION) {
+			/* We could call ieee80211_find_sta too, but checking
+			 * bss_conf is clearer.
+			 */
+			bss_conf = &vif->bss_conf;
+			if (vif_priv->sta_assoc &&
+			    !memcmp(bss_conf->bssid, rsp->addr2, ETH_ALEN)) {
+				found = true;
+				wcn36xx_dbg(WCN36XX_DBG_HAL,
+					    "connection loss bss_index %d\n",
+					    vif_priv->bss_index);
+				ieee80211_connection_loss(vif);
+			}
+		} else {
+			sta = ieee80211_find_sta(vif, rsp->addr2);
+			if (sta) {
+				found = true;
+				ieee80211_report_low_ack(sta, 0);
+			}
+		}
+
 		rcu_read_unlock();
-		if (sta)
+		if (found)
 			return 0;
 	}
 
-	wcn36xx_warn("STA with addr %pM and index %d not found\n",
-		     rsp->addr2,
-		     rsp->sta_id);
+	wcn36xx_warn("BSS or STA with addr %pM not found\n", rsp->addr2);
 	return -ENOENT;
 }
 
@@ -3060,6 +3167,7 @@
 	case WCN36XX_HAL_GTK_OFFLOAD_RSP:
 	case WCN36XX_HAL_GTK_OFFLOAD_GETINFO_RSP:
 	case WCN36XX_HAL_HOST_RESUME_RSP:
+	case WCN36XX_HAL_UPDATE_CHANNEL_LIST_RSP:
 		memcpy(wcn->hal_buf, buf, len);
 		wcn->hal_rsp_len = len;
 		complete(&wcn->hal_rsp_compl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/smd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/smd.h
@@ -70,6 +70,7 @@
 int wcn36xx_smd_start_hw_scan(struct wcn36xx *wcn, struct ieee80211_vif *vif,
 			      struct cfg80211_scan_request *req);
 int wcn36xx_smd_stop_hw_scan(struct wcn36xx *wcn);
+int wcn36xx_smd_update_channel_list(struct wcn36xx *wcn, struct cfg80211_scan_request *req);
 int wcn36xx_smd_add_sta_self(struct wcn36xx *wcn, struct ieee80211_vif *vif);
 int wcn36xx_smd_delete_sta_self(struct wcn36xx *wcn, u8 *addr);
 int wcn36xx_smd_delete_sta(struct wcn36xx *wcn, u8 sta_index);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/txrx.c
@@ -31,6 +31,13 @@
 	enum rate_info_bw bw;
 };
 
+/* Buffer descriptor rx_ch field is limited to 5-bit (4+1), a mapping is used
+ * for 11A Channels.
+ */
+static const u8 ab_rx_ch_map[] = { 36, 40, 44, 48, 52, 56, 60, 64, 100, 104,
+				   108, 112, 116, 120, 124, 128, 132, 136, 140,
+				   149, 153, 157, 161, 165, 144 };
+
 static const struct wcn36xx_rate wcn36xx_rate_table[] = {
 	/* 11b rates */
 	{  10, 0, RX_ENC_LEGACY, 0, RATE_INFO_BW_20 },
@@ -230,7 +237,6 @@
 	const struct wcn36xx_rate *rate;
 	struct ieee80211_hdr *hdr;
 	struct wcn36xx_rx_bd *bd;
-	struct ieee80211_supported_band *sband;
 	u16 fc, sn;
 
 	/*
@@ -252,8 +258,6 @@
 	fc = __le16_to_cpu(hdr->frame_control);
 	sn = IEEE80211_SEQ_TO_SN(__le16_to_cpu(hdr->seq_ctrl));
 
-	status.freq = WCN36XX_CENTER_FREQ(wcn);
-	status.band = WCN36XX_BAND(wcn);
 	status.mactime = 10;
 	status.signal = -get_rssi0(bd);
 	status.antenna = 1;
@@ -265,18 +269,36 @@
 
 	wcn36xx_dbg(WCN36XX_DBG_RX, "status.flags=%x\n", status.flag);
 
+	if (bd->scan_learn) {
+		/* If packet originate from hardware scanning, extract the
+		 * band/channel from bd descriptor.
+		 */
+		u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
+
+		if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
+			status.band = NL80211_BAND_5GHZ;
+			status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
+								     status.band);
+		} else {
+			status.band = NL80211_BAND_2GHZ;
+			status.freq = ieee80211_channel_to_frequency(hwch, status.band);
+		}
+	} else {
+		status.band = WCN36XX_BAND(wcn);
+		status.freq = WCN36XX_CENTER_FREQ(wcn);
+	}
+
 	if (bd->rate_id < ARRAY_SIZE(wcn36xx_rate_table)) {
 		rate = &wcn36xx_rate_table[bd->rate_id];
 		status.encoding = rate->encoding;
 		status.enc_flags = rate->encoding_flags;
 		status.bw = rate->bw;
 		status.rate_idx = rate->mcs_or_legacy_index;
-		sband = wcn->hw->wiphy->bands[status.band];
 		status.nss = 1;
 
 		if (status.band == NL80211_BAND_5GHZ &&
 		    status.encoding == RX_ENC_LEGACY &&
-		    status.rate_idx >= sband->n_bitrates) {
+		    status.rate_idx >= 4) {
 			/* no dsss rates in 5Ghz rates table */
 			status.rate_idx -= 4;
 		}
@@ -321,8 +343,6 @@
 		bd->pdu.mpdu_header_off;
 	bd->pdu.mpdu_len = len;
 	bd->pdu.tid = tid;
-	/* Use seq number generated by mac80211 */
-	bd->pdu.bd_ssn = WCN36XX_TXBD_SSN_FILL_HOST;
 }
 
 static inline struct wcn36xx_vif *get_vif_by_addr(struct wcn36xx *wcn,
@@ -419,6 +439,9 @@
 		tid = ieee80211_get_tid(hdr);
 		/* TID->QID is one-to-one mapping */
 		bd->queue_id = tid;
+		bd->pdu.bd_ssn = WCN36XX_TXBD_SSN_FILL_DPU_QOS;
+	} else {
+		bd->pdu.bd_ssn = WCN36XX_TXBD_SSN_FILL_DPU_NON_QOS;
 	}
 
 	if (info->flags & IEEE80211_TX_INTFL_DONT_ENCRYPT ||
@@ -429,6 +452,9 @@
 	if (ieee80211_is_any_nullfunc(hdr->frame_control)) {
 		/* Don't use a regular queue for null packet (no ampdu) */
 		bd->queue_id = WCN36XX_TX_U_WQ_ID;
+		bd->bd_rate = WCN36XX_BD_RATE_CTRL;
+		if (ieee80211_is_qos_nullfunc(hdr->frame_control))
+			bd->pdu.bd_ssn = WCN36XX_TXBD_SSN_FILL_HOST;
 	}
 
 	if (bcast) {
@@ -488,6 +514,8 @@
 		bd->queue_id = WCN36XX_TX_U_WQ_ID;
 	*vif_priv = __vif_priv;
 
+	bd->pdu.bd_ssn = WCN36XX_TXBD_SSN_FILL_DPU_NON_QOS;
+
 	wcn36xx_set_tx_pdu(bd,
 			   ieee80211_is_data_qos(hdr->frame_control) ?
 			   sizeof(struct ieee80211_qos_hdr) :
@@ -502,10 +530,11 @@
 	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
 	struct wcn36xx_vif *vif_priv = NULL;
 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
-	unsigned long flags;
 	bool is_low = ieee80211_is_data(hdr->frame_control);
 	bool bcast = is_broadcast_ether_addr(hdr->addr1) ||
 		is_multicast_ether_addr(hdr->addr1);
+	bool ack_ind = (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS) &&
+					!(info->flags & IEEE80211_TX_CTL_NO_ACK);
 	struct wcn36xx_tx_bd bd;
 	int ret;
 
@@ -521,30 +550,16 @@
 
 	bd.dpu_rf = WCN36XX_BMU_WQ_TX;
 
-	if (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS) {
+	if (unlikely(ack_ind)) {
 		wcn36xx_dbg(WCN36XX_DBG_DXE, "TX_ACK status requested\n");
 
-		spin_lock_irqsave(&wcn->dxe_lock, flags);
-		if (wcn->tx_ack_skb) {
-			spin_unlock_irqrestore(&wcn->dxe_lock, flags);
-			wcn36xx_warn("tx_ack_skb already set\n");
-			return -EINVAL;
-		}
-
-		wcn->tx_ack_skb = skb;
-		spin_unlock_irqrestore(&wcn->dxe_lock, flags);
-
 		/* Only one at a time is supported by fw. Stop the TX queues
 		 * until the ack status gets back.
 		 */
 		ieee80211_stop_queues(wcn->hw);
 
-		/* TX watchdog if no TX irq or ack indication received  */
-		mod_timer(&wcn->tx_ack_timer, jiffies + HZ / 10);
-
 		/* Request ack indication from the firmware */
-		if (!(info->flags & IEEE80211_TX_CTL_NO_ACK))
-			bd.tx_comp = 1;
+		bd.tx_comp = 1;
 	}
 
 	/* Data frames served first*/
@@ -558,14 +573,8 @@
 	bd.tx_bd_sign = 0xbdbdbdbd;
 
 	ret = wcn36xx_dxe_tx_frame(wcn, vif_priv, &bd, skb, is_low);
-	if (ret && (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)) {
-		/* If the skb has not been transmitted,
-		 * don't keep a reference to it.
-		 */
-		spin_lock_irqsave(&wcn->dxe_lock, flags);
-		wcn->tx_ack_skb = NULL;
-		spin_unlock_irqrestore(&wcn->dxe_lock, flags);
-
+	if (unlikely(ret && ack_ind)) {
+		/* If the skb has not been transmitted, resume TX queue */
 		ieee80211_wake_queues(wcn->hw);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/txrx.h
@@ -110,7 +110,8 @@
 	/* 0x44 */
 	u32	exp_seq_num:12;
 	u32	cur_seq_num:12;
-	u32	fr_type_subtype:8;
+	u32	rf_band:2;
+	u32	fr_type_subtype:6;
 
 	/* 0x48 */
 	u32	msdu_size:16;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wcn36xx/wcn36xx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wcn36xx/wcn36xx.h
@@ -97,6 +97,7 @@
 
 #define RF_UNKNOWN	0x0000
 #define RF_IRIS_WCN3620	0x3620
+#define RF_IRIS_WCN3660	0x3660
 #define RF_IRIS_WCN3680	0x3680
 
 static inline void buff_to_be(u32 *buf, size_t len)
@@ -128,7 +129,6 @@
 	enum wcn36xx_hal_bss_type bss_type;
 
 	/* Power management */
-	bool allow_bmps;
 	enum wcn36xx_power_state pw_state;
 
 	u8 bss_index;
@@ -247,6 +247,7 @@
 	struct cfg80211_scan_request *scan_req;
 	bool			sw_scan;
 	u8			sw_scan_opchannel;
+	bool			sw_scan_init;
 	u8			sw_scan_channel;
 	struct ieee80211_vif	*sw_scan_vif;
 	struct mutex		scan_lock;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wil6210/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -1010,20 +1010,14 @@
 	void *cmd;
 	int cmdlen = len - sizeof(struct wmi_cmd_hdr);
 	u16 cmdid;
-	int rc, rc1;
+	int rc1;
 
-	if (cmdlen < 0)
+	if (cmdlen < 0 || *ppos != 0)
 		return -EINVAL;
 
-	wmi = kmalloc(len, GFP_KERNEL);
-	if (!wmi)
-		return -ENOMEM;
-
-	rc = simple_write_to_buffer(wmi, len, ppos, buf, len);
-	if (rc < 0) {
-		kfree(wmi);
-		return rc;
-	}
+	wmi = memdup_user(buf, len);
+	if (IS_ERR(wmi))
+		return PTR_ERR(wmi);
 
 	cmd = (cmdlen > 0) ? &wmi[1] : NULL;
 	cmdid = le16_to_cpu(wmi->command_id);
@@ -1033,7 +1027,7 @@
 
 	wil_info(wil, "0x%04x[%d] -> %d\n", cmdid, cmdlen, rc1);
 
-	return rc;
+	return len;
 }
 
 static const struct file_operations fops_wmi = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wil6210/txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wil6210/txrx.c
@@ -666,7 +666,7 @@
 	struct wil_tid_crypto_rx *c = mc ? &s->group_crypto_rx :
 				      &s->tid_crypto_rx[tid];
 	struct wil_tid_crypto_rx_single *cc = &c->key_id[key_id];
-	const u8 *pn = (u8 *)&d->mac.pn_15_0;
+	const u8 *pn = (u8 *)&d->mac.pn;
 
 	if (!cc->key_set) {
 		wil_err_ratelimited(wil,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wil6210/txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wil6210/txrx.h
@@ -343,8 +343,10 @@
 	u32 d0;
 	u32 d1;
 	u16 w4;
-	u16 pn_15_0;
-	u32 pn_47_16;
+	struct_group_attr(pn, __packed,
+		u16 pn_15_0;
+		u32 pn_47_16;
+	);
 } __packed;
 
 /* Rx descriptor - DMA part
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wil6210/txrx_edma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wil6210/txrx_edma.c
@@ -548,7 +548,7 @@
 	s = &wil->sta[cid];
 	c = mc ? &s->group_crypto_rx : &s->tid_crypto_rx[tid];
 	cc = &c->key_id[key_id];
-	pn = (u8 *)&st->ext.pn_15_0;
+	pn = (u8 *)&st->ext.pn;
 
 	if (!cc->key_set) {
 		wil_err_ratelimited(wil,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ath/wil6210/txrx_edma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ath/wil6210/txrx_edma.h
@@ -330,8 +330,10 @@
 	u32 d0;
 	u32 d1;
 	__le16 seq_num; /* only lower 12 bits */
-	u16 pn_15_0;
-	u32 pn_47_16;
+	struct_group_attr(pn, __packed,
+		u16 pn_15_0;
+		u32 pn_47_16;
+	);
 } __packed;
 
 struct wil_rx_status_extended {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/atmel/atmel_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/atmel/atmel_cs.c
@@ -72,6 +72,7 @@
 static int atmel_probe(struct pcmcia_device *p_dev)
 {
 	struct local_info *local;
+	int ret;
 
 	dev_dbg(&p_dev->dev, "atmel_attach()\n");
 
@@ -82,8 +83,16 @@
 
 	p_dev->priv = local;
 
-	return atmel_config(p_dev);
-} /* atmel_attach */
+	ret = atmel_config(p_dev);
+	if (ret)
+		goto err_free_priv;
+
+	return 0;
+
+err_free_priv:
+	kfree(p_dev->priv);
+	return ret;
+}
 
 static void atmel_detach(struct pcmcia_device *link)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43/b43.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43/b43.h
@@ -651,7 +651,7 @@
 	union {
 		__be16 d16;
 		__be32 d32;
-	} data __packed;
+	} __packed data;
 } __packed;
 
 
@@ -1082,6 +1082,22 @@
 	return dev->__using_pio_transfers;
 }
 
+static inline void b43_wake_queue(struct b43_wldev *dev, int queue_prio)
+{
+	if (dev->qos_enabled)
+		ieee80211_wake_queue(dev->wl->hw, queue_prio);
+	else
+		ieee80211_wake_queue(dev->wl->hw, 0);
+}
+
+static inline void b43_stop_queue(struct b43_wldev *dev, int queue_prio)
+{
+	if (dev->qos_enabled)
+		ieee80211_stop_queue(dev->wl->hw, queue_prio);
+	else
+		ieee80211_stop_queue(dev->wl->hw, 0);
+}
+
 /* Message printing */
 __printf(2, 3) void b43info(struct b43_wl *wl, const char *fmt, ...);
 __printf(2, 3) void b43err(struct b43_wl *wl, const char *fmt, ...);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43/dma.c
@@ -1399,7 +1399,7 @@
 	    should_inject_overflow(ring)) {
 		/* This TX ring is full. */
 		unsigned int skb_mapping = skb_get_queue_mapping(skb);
-		ieee80211_stop_queue(dev->wl->hw, skb_mapping);
+		b43_stop_queue(dev, skb_mapping);
 		dev->wl->tx_queue_stopped[skb_mapping] = true;
 		ring->stopped = true;
 		if (b43_debug(dev, B43_DBG_DMAVERBOSE)) {
@@ -1570,7 +1570,7 @@
 	} else {
 		/* If the driver queue is running wake the corresponding
 		 * mac80211 queue. */
-		ieee80211_wake_queue(dev->wl->hw, ring->queue_prio);
+		b43_wake_queue(dev, ring->queue_prio);
 		if (b43_debug(dev, B43_DBG_DMAVERBOSE)) {
 			b43dbg(dev->wl, "Woke up TX ring %d\n", ring->index);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43/main.c
@@ -2587,7 +2587,8 @@
 
 start_ieee80211:
 	wl->hw->queues = B43_QOS_QUEUE_NUM;
-	if (!modparam_qos || dev->fw.opensource)
+	if (!modparam_qos || dev->fw.opensource ||
+	    dev->dev->chip_id == BCMA_CHIP_ID_BCM4331)
 		wl->hw->queues = 1;
 
 	err = ieee80211_register_hw(wl->hw);
@@ -3603,7 +3604,7 @@
 				err = b43_dma_tx(dev, skb);
 			if (err == -ENOSPC) {
 				wl->tx_queue_stopped[queue_num] = true;
-				ieee80211_stop_queue(wl->hw, queue_num);
+				b43_stop_queue(dev, queue_num);
 				skb_queue_head(&wl->tx_queue[queue_num], skb);
 				break;
 			}
@@ -3627,6 +3628,7 @@
 		      struct sk_buff *skb)
 {
 	struct b43_wl *wl = hw_to_b43_wl(hw);
+	u16 skb_queue_mapping;
 
 	if (unlikely(skb->len < 2 + 2 + 6)) {
 		/* Too short, this can't be a valid frame. */
@@ -3635,12 +3637,12 @@
 	}
 	B43_WARN_ON(skb_shinfo(skb)->nr_frags);
 
-	skb_queue_tail(&wl->tx_queue[skb->queue_mapping], skb);
-	if (!wl->tx_queue_stopped[skb->queue_mapping]) {
+	skb_queue_mapping = skb_get_queue_mapping(skb);
+	skb_queue_tail(&wl->tx_queue[skb_queue_mapping], skb);
+	if (!wl->tx_queue_stopped[skb_queue_mapping])
 		ieee80211_queue_work(wl->hw, &wl->tx_work);
-	} else {
-		ieee80211_stop_queue(wl->hw, skb->queue_mapping);
-	}
+	else
+		b43_stop_queue(wl->current_dev, skb_queue_mapping);
 }
 
 static void b43_qos_params_upload(struct b43_wldev *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43/phy_g.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43/phy_g.c
@@ -2297,7 +2297,7 @@
 	b43_phy_mask(dev, B43_PHY_G_CRS, 0x7FFF);
 	b43_set_all_gains(dev, 3, 8, 1);
 
-	start = (channel - 5 > 0) ? channel - 5 : 1;
+	start = (channel > 5) ? channel - 5 : 1;
 	end = (channel + 5 < 14) ? channel + 5 : 13;
 
 	for (i = start; i <= end; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43/phy_n.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43/phy_n.c
@@ -582,7 +582,7 @@
 	u16 data[4];
 	s16 gain[2];
 	u16 minmax[2];
-	static const u16 lna_gain[4] = { -2, 10, 19, 25 };
+	static const s16 lna_gain[4] = { -2, 10, 19, 25 };
 
 	if (nphy->hang_avoid)
 		b43_nphy_stay_in_carrier_search(dev, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43/pio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43/pio.c
@@ -525,7 +525,7 @@
 	if (total_len > (q->buffer_size - q->buffer_used)) {
 		/* Not enough memory on the queue. */
 		err = -EBUSY;
-		ieee80211_stop_queue(dev->wl->hw, skb_get_queue_mapping(skb));
+		b43_stop_queue(dev, skb_get_queue_mapping(skb));
 		q->stopped = true;
 		goto out;
 	}
@@ -552,7 +552,7 @@
 	if (((q->buffer_size - q->buffer_used) < roundup(2 + 2 + 6, 4)) ||
 	    (q->free_packet_slots == 0)) {
 		/* The queue is full. */
-		ieee80211_stop_queue(dev->wl->hw, skb_get_queue_mapping(skb));
+		b43_stop_queue(dev, skb_get_queue_mapping(skb));
 		q->stopped = true;
 	}
 
@@ -587,7 +587,7 @@
 	list_add(&pack->list, &q->packets_list);
 
 	if (q->stopped) {
-		ieee80211_wake_queue(dev->wl->hw, q->queue_prio);
+		b43_wake_queue(dev, q->queue_prio);
 		q->stopped = false;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43legacy/b43legacy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43legacy/b43legacy.h
@@ -379,7 +379,7 @@
 	union {
 		__be16 d16;
 		__be32 d32;
-	} data __packed;
+	} __packed data;
 } __packed;
 
 #define B43legacy_PHYMODE(phytype)	(1 << (phytype))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43legacy/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43legacy/phy.c
@@ -1123,7 +1123,7 @@
 	struct b43legacy_phy *phy = &dev->phy;
 	u16 regstack[12] = { 0 };
 	u16 mls;
-	u16 fval;
+	s16 fval;
 	int i;
 	int j;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/b43legacy/radio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/b43legacy/radio.c
@@ -283,7 +283,7 @@
 			    & 0x7FFF);
 	b43legacy_set_all_gains(dev, 3, 8, 1);
 
-	start = (channel - 5 > 0) ? channel - 5 : 1;
+	start = (channel > 5) ? channel - 5 : 1;
 	end = (channel + 5 < 14) ? channel + 5 : 13;
 
 	for (i = start; i <= end; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/Kconfig
@@ -23,6 +23,7 @@
 config BRCM_TRACING
 	bool "Broadcom device tracing"
 	depends on BRCMSMAC || BRCMFMAC
+	depends on TRACING
 	help
 	  If you say Y here, the Broadcom wireless drivers will register
 	  with ftrace to dump event information into the trace ringbuffer.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
@@ -770,7 +770,7 @@
 
 	nents = max_t(uint, BRCMF_DEFAULT_RXGLOM_SIZE,
 		      sdiodev->settings->bus.sdio.txglomsz);
-	nents += (nents >> 4) + 1;
+	nents *= 2;
 
 	WARN_ON(nents > sdiodev->max_segment_count);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
@@ -90,6 +90,9 @@
 #define BRCMF_ASSOC_PARAMS_FIXED_SIZE \
 	(sizeof(struct brcmf_assoc_params_le) - sizeof(u16))
 
+#define BRCMF_MAX_CHANSPEC_LIST \
+	(BRCMF_DCMD_MEDLEN / sizeof(__le32) - 1)
+
 static bool check_vif_up(struct brcmf_cfg80211_vif *vif)
 {
 	if (!test_bit(BRCMF_VIF_STATUS_READY, &vif->sme_state)) {
@@ -787,8 +790,7 @@
 	scan_request = cfg->scan_request;
 	cfg->scan_request = NULL;
 
-	if (timer_pending(&cfg->escan_timeout))
-		del_timer_sync(&cfg->escan_timeout);
+	timer_delete_sync(&cfg->escan_timeout);
 
 	if (fw_abort) {
 		/* Do a scan abort to stop the driver's scan engine */
@@ -1347,13 +1349,14 @@
 {
 	struct brcmf_pub *drvr = ifp->drvr;
 	struct brcmf_wsec_pmk_le pmk;
-	int i, err;
+	int err;
 
-	/* convert to firmware key format */
-	pmk.key_len = cpu_to_le16(pmk_len << 1);
-	pmk.flags = cpu_to_le16(BRCMF_WSEC_PASSPHRASE);
-	for (i = 0; i < pmk_len; i++)
-		snprintf(&pmk.key[2 * i], 3, "%02x", pmk_data[i]);
+	memset(&pmk, 0, sizeof(pmk));
+
+	/* pass pmk directly */
+	pmk.key_len = cpu_to_le16(pmk_len);
+	pmk.flags = cpu_to_le16(0);
+	memcpy(pmk.key, pmk_data, pmk_len);
 
 	/* store psk in firmware */
 	err = brcmf_fil_cmd_data_set(ifp, BRCMF_C_SET_WSEC_PMK,
@@ -5887,6 +5890,11 @@
 		(struct brcmf_cfg80211_assoc_ielen_le *)cfg->extra_buf;
 	req_len = le32_to_cpu(assoc_info->req_len);
 	resp_len = le32_to_cpu(assoc_info->resp_len);
+	if (req_len > WL_EXTRA_BUF_MAX || resp_len > WL_EXTRA_BUF_MAX) {
+		bphy_err(drvr, "invalid lengths in assoc info: req %u resp %u\n",
+			 req_len, resp_len);
+		return -EINVAL;
+	}
 	if (req_len) {
 		err = brcmf_fil_iovar_data_get(ifp, "assoc_req_ies",
 					       cfg->extra_buf,
@@ -6204,18 +6212,20 @@
 {
 	struct brcmf_cfg80211_vif *vif = ifp->vif;
 	struct brcmf_rssi_be *info = data;
-	s32 rssi, snr, noise;
+	s32 rssi, snr = 0, noise = 0;
 	s32 low, high, last;
 
-	if (e->datalen < sizeof(*info)) {
+	if (e->datalen >= sizeof(*info)) {
+		rssi = be32_to_cpu(info->rssi);
+		snr = be32_to_cpu(info->snr);
+		noise = be32_to_cpu(info->noise);
+	} else if (e->datalen >= sizeof(rssi)) {
+		rssi = be32_to_cpu(*(__be32 *)data);
+	} else {
 		brcmf_err("insufficient RSSI event data\n");
 		return 0;
 	}
 
-	rssi = be32_to_cpu(info->rssi);
-	snr = be32_to_cpu(info->snr);
-	noise = be32_to_cpu(info->noise);
-
 	low = vif->cqm_rssi_low;
 	high = vif->cqm_rssi_high;
 	last = vif->cqm_rssi_last;
@@ -6557,6 +6567,13 @@
 			band->channels[i].flags = IEEE80211_CHAN_DISABLED;
 
 	total = le32_to_cpu(list->count);
+	if (total > BRCMF_MAX_CHANSPEC_LIST) {
+		bphy_err(drvr, "Invalid count of channel Spec. (%u)\n",
+			 total);
+		err = -EINVAL;
+		goto fail_pbuf;
+	}
+
 	for (i = 0; i < total; i++) {
 		ch.chspec = (u16)le32_to_cpu(list->element[i]);
 		cfg->d11inf.decchspec(&ch);
@@ -6702,6 +6719,13 @@
 		band = cfg_to_wiphy(cfg)->bands[NL80211_BAND_2GHZ];
 		list = (struct brcmf_chanspec_list *)pbuf;
 		num_chan = le32_to_cpu(list->count);
+		if (num_chan > BRCMF_MAX_CHANSPEC_LIST) {
+			bphy_err(drvr, "Invalid count of channel Spec. (%u)\n",
+				 num_chan);
+			kfree(pbuf);
+			return -EINVAL;
+		}
+
 		for (i = 0; i < num_chan; i++) {
 			ch.chspec = (u16)le32_to_cpu(list->element[i]);
 			cfg->d11inf.decchspec(&ch);
@@ -7756,6 +7780,7 @@
 	brcmf_btcoex_detach(cfg);
 	wiphy_unregister(cfg->wiphy);
 	wl_deinit_priv(cfg);
+	cancel_work_sync(&cfg->escan_timeout_work);
 	brcmf_free_wiphy(cfg->wiphy);
 	kfree(cfg);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
@@ -264,6 +264,7 @@
 			 err);
 		goto done;
 	}
+	buf[sizeof(buf) - 1] = '\0';
 	ptr = (char *)buf;
 	strsep(&ptr, "\n");
 
@@ -280,15 +281,17 @@
 	if (err) {
 		brcmf_dbg(TRACE, "retrieving clmver failed, %d\n", err);
 	} else {
+		buf[sizeof(buf) - 1] = '\0';
 		clmver = (char *)buf;
-		/* store CLM version for adding it to revinfo debugfs file */
-		memcpy(ifp->drvr->clmver, clmver, sizeof(ifp->drvr->clmver));
 
 		/* Replace all newline/linefeed characters with space
 		 * character
 		 */
 		strreplace(clmver, '\n', ' ');
 
+		/* store CLM version for adding it to revinfo debugfs file */
+		memcpy(ifp->drvr->clmver, clmver, sizeof(ifp->drvr->clmver));
+
 		brcmf_dbg(INFO, "CLM version = %s\n", clmver);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c
@@ -295,6 +295,7 @@
 	struct brcmf_pub *drvr = ifp->drvr;
 	struct ethhdr *eh;
 	int head_delta;
+	unsigned int tx_bytes = skb->len;
 
 	brcmf_dbg(DATA, "Enter, bsscfgidx=%d\n", ifp->bsscfgidx);
 
@@ -337,6 +338,7 @@
 			bphy_err(drvr, "%s: failed to expand headroom\n",
 				 brcmf_ifname(ifp));
 			atomic_inc(&drvr->bus_if->stats.pktcow_failed);
+			dev_kfree_skb(skb);
 			goto done;
 		}
 	}
@@ -369,7 +371,7 @@
 		ndev->stats.tx_dropped++;
 	} else {
 		ndev->stats.tx_packets++;
-		ndev->stats.tx_bytes += skb->len;
+		ndev->stats.tx_bytes += tx_bytes;
 	}
 
 	/* Return ok: we always eat the packet */
@@ -548,6 +550,11 @@
 	struct ethhdr *eh;
 	u16 type;
 
+	if (!ifp) {
+		brcmu_pkt_buf_free_skb(txp);
+		return;
+	}
+
 	eh = (struct ethhdr *)(txp->data);
 	type = ntohs(eh->h_proto);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c
@@ -76,6 +76,16 @@
 		.driver_data = (void *)&acepc_t8_data,
 	},
 	{
+		/* Cyberbook T116 rugged tablet */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "Default string"),
+			DMI_EXACT_MATCH(DMI_BOARD_NAME, "Cherry Trail CR"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "20170531"),
+		},
+		/* The factory image nvram file is identical to the ACEPC T8 one */
+		.driver_data = (void *)&acepc_t8_data,
+	},
+	{
 		/* Match for the GPDwin which unfortunately uses somewhat
 		 * generic dmi strings, which is why we test for 4 strings.
 		 * Comparing against 23 other byt/cht boards, board_vendor
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
@@ -207,6 +207,8 @@
 		size = BRCMF_FW_MAX_NVRAM_SIZE;
 	else
 		size = data_len;
+	/* Add space for properties we may add */
+	size += strlen(BRCMF_FW_DEFAULT_BOARDREV) + 1;
 	/* Alloc for extra 0 byte + roundup by 4 + length field */
 	size += 1 + 3 + sizeof(u32);
 	nvp->nvram = kzalloc(size, GFP_KERNEL);
@@ -693,7 +695,7 @@
 {
 	struct brcmf_fw_item *first = &req->items[0];
 	struct brcmf_fw *fwctx;
-	char *alt_path;
+	char *alt_path = NULL;
 	int ret;
 
 	brcmf_dbg(TRACE, "enter: dev=%s\n", dev_name(dev));
@@ -712,7 +714,9 @@
 	fwctx->done = fw_cb;
 
 	/* First try alternative board-specific path if any */
-	alt_path = brcm_alt_fw_path(first->path, fwctx->req->board_type);
+	if (fwctx->req->board_type)
+		alt_path = brcm_alt_fw_path(first->path,
+					    fwctx->req->board_type);
 	if (alt_path) {
 		ret = request_firmware_nowait(THIS_MODULE, true, alt_path,
 					      fwctx->dev, GFP_KERNEL, fwctx,
@@ -742,6 +746,11 @@
 	u32 i, j;
 	char end = '\0';
 
+	if (chiprev >= BITS_PER_TYPE(u32)) {
+		brcmf_err("Invalid chip revision %u\n", chiprev);
+		return NULL;
+	}
+
 	for (i = 0; i < table_size; i++) {
 		if (mapping_table[i].chipid == chip &&
 		    mapping_table[i].revmask & BIT(chiprev))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c
@@ -228,6 +228,10 @@
 			  brcmf_fweh_event_name(event->code), event->code,
 			  event->emsg.ifidx, event->emsg.bsscfgidx,
 			  event->emsg.addr);
+		if (event->emsg.bsscfgidx >= BRCMF_MAX_IFS) {
+			bphy_err(drvr, "invalid bsscfg index: %u\n", event->emsg.bsscfgidx);
+			goto event_free;
+		}
 
 		/* convert event message */
 		emsg_be = &event->emsg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h
@@ -383,7 +383,12 @@
 				 * fixed parameter portion is assumed, otherwise
 				 * ssid in the fixed portion is ignored
 				 */
-	__le16 channel_list[1];	/* list of chanspecs */
+	union {
+		__le16 padding;	/* Reserve space for at least 1 entry for abort
+				 * which uses an on stack brcmf_scan_params_le
+				 */
+		DECLARE_FLEX_ARRAY(__le16, channel_list);	/* chanspecs */
+	};
 };
 
 struct brcmf_scan_results {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c
@@ -346,8 +346,11 @@
 		count++;
 	} while (count < pktids->array_size);
 
-	if (count == pktids->array_size)
+	if (count == pktids->array_size) {
+		dma_unmap_single(dev, *physaddr, skb->len - data_offset,
+				 pktids->direction);
 		return -ENOMEM;
+	}
 
 	array[*idx].data_offset = data_offset;
 	array[*idx].physaddr = *physaddr;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c
@@ -12,6 +12,7 @@
 #include <linux/interrupt.h>
 #include <linux/bcma/bcma.h>
 #include <linux/sched.h>
+#include <linux/io.h>
 #include <asm/unaligned.h>
 
 #include <soc.h>
@@ -59,6 +60,13 @@
 BRCMF_FW_DEF(4366C, "brcmfmac4366c-pcie");
 BRCMF_FW_DEF(4371, "brcmfmac4371-pcie");
 
+/* firmware config files */
+MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.txt");
+MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.*.txt");
+
+/* per-board firmware binaries */
+MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.*.bin");
+
 static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = {
 	BRCMF_FW_ENTRY(BRCM_CC_43602_CHIP_ID, 0xFFFFFFFF, 43602),
 	BRCMF_FW_ENTRY(BRCM_CC_43465_CHIP_ID, 0xFFFFFFF0, 4366C),
@@ -448,47 +456,6 @@
 
 
 static void
-brcmf_pcie_copy_mem_todev(struct brcmf_pciedev_info *devinfo, u32 mem_offset,
-			  void *srcaddr, u32 len)
-{
-	void __iomem *address = devinfo->tcm + mem_offset;
-	__le32 *src32;
-	__le16 *src16;
-	u8 *src8;
-
-	if (((ulong)address & 4) || ((ulong)srcaddr & 4) || (len & 4)) {
-		if (((ulong)address & 2) || ((ulong)srcaddr & 2) || (len & 2)) {
-			src8 = (u8 *)srcaddr;
-			while (len) {
-				iowrite8(*src8, address);
-				address++;
-				src8++;
-				len--;
-			}
-		} else {
-			len = len / 2;
-			src16 = (__le16 *)srcaddr;
-			while (len) {
-				iowrite16(le16_to_cpu(*src16), address);
-				address += 2;
-				src16++;
-				len--;
-			}
-		}
-	} else {
-		len = len / 4;
-		src32 = (__le32 *)srcaddr;
-		while (len) {
-			iowrite32(le32_to_cpu(*src32), address);
-			address += 4;
-			src32++;
-			len--;
-		}
-	}
-}
-
-
-static void
 brcmf_pcie_copy_dev_tomem(struct brcmf_pciedev_info *devinfo, u32 mem_offset,
 			  void *dstaddr, u32 len)
 {
@@ -659,7 +626,7 @@
 	}
 
 	if (!brcmf_chip_set_active(devinfo->ci, resetintr))
-		return -EINVAL;
+		return -EIO;
 	return 0;
 }
 
@@ -1151,6 +1118,10 @@
 				BRCMF_NROF_H2D_COMMON_MSGRINGS;
 		max_completionrings = BRCMF_NROF_D2H_COMMON_MSGRINGS;
 	}
+	if (max_flowrings > 512) {
+		brcmf_err(bus, "invalid max_flowrings(%d)\n", max_flowrings);
+		return -EIO;
+	}
 
 	if (devinfo->dma_idx_sz != 0) {
 		bufsz = (max_submissionrings + max_completionrings) *
@@ -1348,6 +1319,18 @@
 {
 }
 
+static int brcmf_pcie_preinit(struct device *dev)
+{
+	struct brcmf_bus *bus_if = dev_get_drvdata(dev);
+	struct brcmf_pciedev *buspub = bus_if->bus_priv.pcie;
+
+	brcmf_dbg(PCIE, "Enter\n");
+
+	brcmf_pcie_intr_enable(buspub->devinfo);
+	brcmf_pcie_hostready(buspub->devinfo);
+
+	return 0;
+}
 
 static int brcmf_pcie_tx(struct device *dev, struct sk_buff *skb)
 {
@@ -1456,6 +1439,7 @@
 }
 
 static const struct brcmf_bus_ops brcmf_pcie_bus_ops = {
+	.preinit = brcmf_pcie_preinit,
 	.txdata = brcmf_pcie_tx,
 	.stop = brcmf_pcie_down,
 	.txctl = brcmf_pcie_tx_ctlpkt,
@@ -1563,8 +1547,8 @@
 		return err;
 
 	brcmf_dbg(PCIE, "Download FW %s\n", devinfo->fw_name);
-	brcmf_pcie_copy_mem_todev(devinfo, devinfo->ci->rambase,
-				  (void *)fw->data, fw->size);
+	memcpy_toio(devinfo->tcm + devinfo->ci->rambase,
+		    (void *)fw->data, fw->size);
 
 	resetintr = get_unaligned_le32(fw->data);
 	release_firmware(fw);
@@ -1578,7 +1562,7 @@
 		brcmf_dbg(PCIE, "Download NVRAM %s\n", devinfo->nvram_name);
 		address = devinfo->ci->rambase + devinfo->ci->ramsize -
 			  nvram_len;
-		brcmf_pcie_copy_mem_todev(devinfo, address, nvram, nvram_len);
+		memcpy_toio(devinfo->tcm + address, nvram, nvram_len);
 		brcmf_fw_nvram_free(nvram);
 	} else {
 		brcmf_dbg(PCIE, "No matching NVRAM file found %s\n",
@@ -1777,6 +1761,8 @@
 	ret = brcmf_chip_get_raminfo(devinfo->ci);
 	if (ret) {
 		brcmf_err(bus, "Failed to get RAM info\n");
+		release_firmware(fw);
+		brcmf_fw_nvram_free(nvram);
 		goto fail;
 	}
 
@@ -1826,9 +1812,6 @@
 
 	init_waitqueue_head(&devinfo->mbdata_resp_wait);
 
-	brcmf_pcie_intr_enable(devinfo);
-	brcmf_pcie_hostready(devinfo);
-
 	ret = brcmf_attach(&devinfo->pdev->dev);
 	if (ret)
 		goto fail;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pno.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pno.c
@@ -158,12 +158,12 @@
 	struct brcmf_pno_macaddr_le pfn_mac;
 	u8 *mac_addr = NULL;
 	u8 *mac_mask = NULL;
-	int err, i;
+	int err, i, ri;
 
-	for (i = 0; i < pi->n_reqs; i++)
-		if (pi->reqs[i]->flags & NL80211_SCAN_FLAG_RANDOM_ADDR) {
-			mac_addr = pi->reqs[i]->mac_addr;
-			mac_mask = pi->reqs[i]->mac_addr_mask;
+	for (ri = 0; ri < pi->n_reqs; ri++)
+		if (pi->reqs[ri]->flags & NL80211_SCAN_FLAG_RANDOM_ADDR) {
+			mac_addr = pi->reqs[ri]->mac_addr;
+			mac_mask = pi->reqs[ri]->mac_addr_mask;
 			break;
 		}
 
@@ -185,7 +185,7 @@
 	pfn_mac.mac[0] |= 0x02;
 
 	brcmf_dbg(SCAN, "enabling random mac: reqid=%llu mac=%pM\n",
-		  pi->reqs[i]->reqid, pfn_mac.mac);
+		  pi->reqs[ri]->reqid, pfn_mac.mac);
 	err = brcmf_fil_iovar_data_set(ifp, "pfn_macaddr", &pfn_mac,
 				       sizeof(pfn_mac));
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -557,7 +557,7 @@
 	BRCMF_SDIO_FT_SUB,
 };
 
-#define SDIOD_DRVSTR_KEY(chip, pmu)     (((chip) << 16) | (pmu))
+#define SDIOD_DRVSTR_KEY(chip, pmu)     (((unsigned int)(chip) << 16) | (pmu))
 
 /* SDIO Pad drive strength to select value mappings */
 struct sdiod_drive_str {
@@ -629,7 +629,6 @@
 
 /* firmware config files */
 MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-sdio.*.txt");
-MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.*.txt");
 
 /* per-board firmware binaries */
 MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-sdio.*.bin");
@@ -3412,6 +3411,7 @@
 	/* Take arm out of reset */
 	if (!brcmf_chip_set_active(bus->ci, rstvec)) {
 		brcmf_err("error getting out of ARM core reset\n");
+		bcmerror = -EIO;
 		goto err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c
@@ -1088,6 +1088,7 @@
 	ieee80211_hw_set(hw, AMPDU_AGGREGATION);
 	ieee80211_hw_set(hw, SIGNAL_DBM);
 	ieee80211_hw_set(hw, REPORTS_TX_ACK_STATUS);
+	ieee80211_hw_set(hw, MFP_CAPABLE);
 
 	hw->extra_tx_headroom = brcms_c_get_header_len();
 	hw->queues = N_TX_QUEUES;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c
@@ -383,8 +383,9 @@
 	return sh;
 }
 
-static void wlc_phy_timercb_phycal(struct brcms_phy *pi)
+static void wlc_phy_timercb_phycal(void *ptr)
 {
+	struct brcms_phy *pi = ptr;
 	uint delay = 5;
 
 	if (PHY_PERICAL_MPHASE_PENDING(pi)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c
@@ -2567,7 +2567,6 @@
 
 	struct lcnphy_txgains cal_gains, temp_gains;
 	u16 hash;
-	u8 band_idx;
 	int j;
 	u16 ncorr_override[5];
 	u16 syst_coeffs[] = { 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
@@ -2599,6 +2598,9 @@
 	u16 *values_to_save;
 	struct brcms_phy_lcnphy *pi_lcn = pi->u.pi_lcnphy;
 
+	if (WARN_ON(CHSPEC_IS5G(pi->radio_chanspec)))
+		return;
+
 	values_to_save = kmalloc_array(20, sizeof(u16), GFP_ATOMIC);
 	if (NULL == values_to_save)
 		return;
@@ -2662,20 +2664,18 @@
 	hash = (target_gains->gm_gain << 8) |
 	       (target_gains->pga_gain << 4) | (target_gains->pad_gain);
 
-	band_idx = (CHSPEC_IS5G(pi->radio_chanspec) ? 1 : 0);
-
 	cal_gains = *target_gains;
 	memset(ncorr_override, 0, sizeof(ncorr_override));
-	for (j = 0; j < iqcal_gainparams_numgains_lcnphy[band_idx]; j++) {
-		if (hash == tbl_iqcal_gainparams_lcnphy[band_idx][j][0]) {
+	for (j = 0; j < iqcal_gainparams_numgains_lcnphy[0]; j++) {
+		if (hash == tbl_iqcal_gainparams_lcnphy[0][j][0]) {
 			cal_gains.gm_gain =
-				tbl_iqcal_gainparams_lcnphy[band_idx][j][1];
+				tbl_iqcal_gainparams_lcnphy[0][j][1];
 			cal_gains.pga_gain =
-				tbl_iqcal_gainparams_lcnphy[band_idx][j][2];
+				tbl_iqcal_gainparams_lcnphy[0][j][2];
 			cal_gains.pad_gain =
-				tbl_iqcal_gainparams_lcnphy[band_idx][j][3];
+				tbl_iqcal_gainparams_lcnphy[0][j][3];
 			memcpy(ncorr_override,
-			       &tbl_iqcal_gainparams_lcnphy[band_idx][j][3],
+			       &tbl_iqcal_gainparams_lcnphy[0][j][3],
 			       sizeof(ncorr_override));
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c
@@ -23427,6 +23427,9 @@
 				break;
 		}
 
+		if (WARN_ON(k == NPHY_IQCAL_NUMGAINS))
+			return;
+
 		params->txgm = tbl_iqcal_gainparams_nphy[band_idx][k][1];
 		params->pga = tbl_iqcal_gainparams_nphy[band_idx][k][2];
 		params->pad = tbl_iqcal_gainparams_nphy[band_idx][k][3];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c
@@ -57,12 +57,11 @@
 }
 
 struct wlapi_timer *wlapi_init_timer(struct phy_shim_info *physhim,
-				     void (*fn)(struct brcms_phy *pi),
+				     void (*fn)(void *pi),
 				     void *arg, const char *name)
 {
 	return (struct wlapi_timer *)
-			brcms_init_timer(physhim->wl, (void (*)(void *))fn,
-					 arg, name);
+			brcms_init_timer(physhim->wl, fn, arg, name);
 }
 
 void wlapi_free_timer(struct wlapi_timer *t)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.h
@@ -131,7 +131,7 @@
 
 /* PHY to WL utility functions */
 struct wlapi_timer *wlapi_init_timer(struct phy_shim_info *physhim,
-				     void (*fn)(struct brcms_phy *pi),
+				     void (*fn)(void *pi),
 				     void *arg, const char *name);
 void wlapi_free_timer(struct wlapi_timer *t);
 void wlapi_add_timer(struct wlapi_timer *t, uint ms, int periodic);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/cisco/airo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/cisco/airo.c
@@ -5233,7 +5233,7 @@
 	return -1;
 }
 
-static int set_wep_key(struct airo_info *ai, u16 index, const char *key,
+static int set_wep_key(struct airo_info *ai, u16 index, const u8 *key,
 		       u16 keylen, int perm, int lock)
 {
 	static const unsigned char macaddr[ETH_ALEN] = { 0x01, 0, 0, 0, 0, 0 };
@@ -5284,7 +5284,7 @@
 	struct net_device *dev = PDE_DATA(inode);
 	struct airo_info *ai = dev->ml_priv;
 	int i, rc;
-	char key[16];
+	u8 key[16];
 	u16 index = 0;
 	int j = 0;
 
@@ -5312,12 +5312,22 @@
 	}
 
 	for (i = 0; i < 16*3 && data->wbuffer[i+j]; i++) {
+		int val;
+
+		if (i % 3 == 2)
+			continue;
+
+		val = hex_to_bin(data->wbuffer[i+j]);
+		if (val < 0) {
+			airo_print_err(ai->dev->name, "WebKey passed invalid key hex");
+			return;
+		}
 		switch(i%3) {
 		case 0:
-			key[i/3] = hex_to_bin(data->wbuffer[i+j])<<4;
+			key[i/3] = (u8)val << 4;
 			break;
 		case 1:
-			key[i/3] |= hex_to_bin(data->wbuffer[i+j]);
+			key[i/3] |= (u8)val;
 			break;
 		}
 	}
@@ -6137,8 +6147,11 @@
 {
 	struct airo_info *local = dev->ml_priv;
 	StatusRid status_rid;		/* Card status info */
+	int ret;
 
-	readStatusRid(local, &status_rid, 1);
+	ret = readStatusRid(local, &status_rid, 1);
+	if (ret)
+		return -EBUSY;
 
 	vwrq->value = le16_to_cpu(status_rid.currentXmitRate) * 500000;
 	/* If more than one rate, set auto */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/ipw2x00/ipw2200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/ipw2x00/ipw2200.c
@@ -3444,7 +3444,7 @@
 			dma_unmap_single(&priv->pci_dev->dev,
 					 rxq->pool[i].dma_addr,
 					 IPW_RX_BUF_SIZE, DMA_FROM_DEVICE);
-			dev_kfree_skb(rxq->pool[i].skb);
+			dev_kfree_skb_irq(rxq->pool[i].skb);
 			rxq->pool[i].skb = NULL;
 		}
 		list_add_tail(&rxq->pool[i].list, &rxq->rx_used);
@@ -11400,9 +11400,14 @@
 	set_wiphy_dev(wdev->wiphy, &priv->pci_dev->dev);
 
 	/* With that information in place, we can now register the wiphy... */
-	if (wiphy_register(wdev->wiphy))
-		rc = -EIO;
+	rc = wiphy_register(wdev->wiphy);
+	if (rc)
+		goto out;
+
+	return 0;
 out:
+	kfree(priv->ieee->a_band.channels);
+	kfree(priv->ieee->bg_band.channels);
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/ipw2x00/libipw_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/ipw2x00/libipw_rx.c
@@ -870,8 +870,8 @@
 	switch (ieee->iw_mode) {
 	case IW_MODE_ADHOC:
 		/* our BSS and not from/to DS */
-		if (ether_addr_equal(hdr->addr3, ieee->bssid))
-		if ((fc & (IEEE80211_FCTL_TODS+IEEE80211_FCTL_FROMDS)) == 0) {
+		if (ether_addr_equal(hdr->addr3, ieee->bssid) &&
+		    ((fc & (IEEE80211_FCTL_TODS + IEEE80211_FCTL_FROMDS)) == 0)) {
 			/* promisc: get all */
 			if (ieee->dev->flags & IFF_PROMISC)
 				is_packet_for_us = 1;
@@ -885,8 +885,8 @@
 		break;
 	case IW_MODE_INFRA:
 		/* our BSS (== from our AP) and from DS */
-		if (ether_addr_equal(hdr->addr2, ieee->bssid))
-		if ((fc & (IEEE80211_FCTL_TODS+IEEE80211_FCTL_FROMDS)) == IEEE80211_FCTL_FROMDS) {
+		if (ether_addr_equal(hdr->addr2, ieee->bssid) &&
+		    ((fc & (IEEE80211_FCTL_TODS + IEEE80211_FCTL_FROMDS)) == IEEE80211_FCTL_FROMDS)) {
 			/* promisc: get all */
 			if (ieee->dev->flags & IFF_PROMISC)
 				is_packet_for_us = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/ipw2x00/libipw_tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/ipw2x00/libipw_tx.c
@@ -383,7 +383,7 @@
 
 		/* Each fragment may need to have room for encryption
 		 * pre/postfix */
-		if (host_encrypt)
+		if (host_encrypt && crypt && crypt->ops)
 			bytes_per_frag -= crypt->ops->extra_mpdu_prefix_len +
 			    crypt->ops->extra_mpdu_postfix_len;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlegacy/3945-mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlegacy/3945-mac.c
@@ -3378,10 +3378,12 @@
  *
  *****************************************************************************/
 
-static void
+static int
 il3945_setup_deferred_work(struct il_priv *il)
 {
 	il->workqueue = create_singlethread_workqueue(DRV_NAME);
+	if (!il->workqueue)
+		return -ENOMEM;
 
 	init_waitqueue_head(&il->wait_command_queue);
 
@@ -3398,6 +3400,8 @@
 	timer_setup(&il->watchdog, il_bg_watchdog, 0);
 
 	tasklet_setup(&il->irq_tasklet, il3945_irq_tasklet);
+
+	return 0;
 }
 
 static void
@@ -3717,7 +3721,10 @@
 	}
 
 	il_set_rxon_channel(il, &il->bands[NL80211_BAND_2GHZ].channels[5]);
-	il3945_setup_deferred_work(il);
+	err = il3945_setup_deferred_work(il);
+	if (err)
+		goto out_remove_sysfs;
+
 	il3945_setup_handlers(il);
 	il_power_initialize(il);
 
@@ -3729,7 +3736,7 @@
 
 	err = il3945_setup_mac(il);
 	if (err)
-		goto out_remove_sysfs;
+		goto out_destroy_workqueue;
 
 	il_dbgfs_register(il, DRV_NAME);
 
@@ -3738,9 +3745,10 @@
 
 	return 0;
 
-out_remove_sysfs:
+out_destroy_workqueue:
 	destroy_workqueue(il->workqueue);
 	il->workqueue = NULL;
+out_remove_sysfs:
 	sysfs_remove_group(&pdev->dev.kobj, &il3945_attribute_group);
 out_release_irq:
 	free_irq(il->pci_dev->irq, il);
@@ -3819,7 +3827,6 @@
 	il3945_unset_hw_params(il);
 
 	/*netif_stop_queue(dev); */
-	flush_workqueue(il->workqueue);
 
 	/* ieee80211_unregister_hw calls il3945_mac_stop, which flushes
 	 * il->workqueue... so we can't take down the workqueue
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlegacy/4965-mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlegacy/4965-mac.c
@@ -6211,10 +6211,12 @@
 	mutex_unlock(&il->mutex);
 }
 
-static void
+static int
 il4965_setup_deferred_work(struct il_priv *il)
 {
 	il->workqueue = create_singlethread_workqueue(DRV_NAME);
+	if (!il->workqueue)
+		return -ENOMEM;
 
 	init_waitqueue_head(&il->wait_command_queue);
 
@@ -6233,6 +6235,8 @@
 	timer_setup(&il->watchdog, il_bg_watchdog, 0);
 
 	tasklet_setup(&il->irq_tasklet, il4965_irq_tasklet);
+
+	return 0;
 }
 
 static void
@@ -6617,7 +6621,10 @@
 		goto out_disable_msi;
 	}
 
-	il4965_setup_deferred_work(il);
+	err = il4965_setup_deferred_work(il);
+	if (err)
+		goto out_free_irq;
+
 	il4965_setup_handlers(il);
 
 	/*********************************************
@@ -6655,6 +6662,7 @@
 out_destroy_workqueue:
 	destroy_workqueue(il->workqueue);
 	il->workqueue = NULL;
+out_free_irq:
 	free_irq(il->pci_dev->irq, il);
 out_disable_msi:
 	pci_disable_msi(il->pci_dev);
@@ -6731,7 +6739,6 @@
 	il_eeprom_free(il);
 
 	/*netif_stop_queue(dev); */
-	flush_workqueue(il->workqueue);
 
 	/* ieee80211_unregister_hw calls il_mac_stop, which flushes
 	 * il->workqueue... so we can't take down the workqueue
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlegacy/4965-rs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlegacy/4965-rs.c
@@ -2403,7 +2403,7 @@
 		/* Repeat initial/next rate.
 		 * For legacy IL_NUMBER_TRY == 1, this loop will not execute.
 		 * For HT IL_HT_NUMBER_TRY == 3, this executes twice. */
-		while (repeat_rate > 0 && idx < LINK_QUAL_MAX_RETRY_NUM) {
+		while (repeat_rate > 0 && idx < (LINK_QUAL_MAX_RETRY_NUM - 1)) {
 			if (is_legacy(tbl_type.lq_type)) {
 				if (ant_toggle_cnt < NUM_TRY_BEFORE_ANT_TOGGLE)
 					ant_toggle_cnt++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlegacy/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlegacy/common.c
@@ -4960,6 +4960,8 @@
 	 */
 	pci_write_config_byte(pdev, PCI_CFG_RETRY_TIMEOUT, 0x00);
 
+	_il_wr(il, CSR_INT, 0xffffffff);
+	_il_wr(il, CSR_FH_INT_STATUS, 0xffffffff);
 	il_enable_interrupts(il);
 
 	if (!(_il_rd(il, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW))
@@ -5173,7 +5175,7 @@
 	memset(&il->current_ht_config, 0, sizeof(struct il_ht_config));
 
 	/* new association get rid of ibss beacon skb */
-	dev_kfree_skb(il->beacon_skb);
+	dev_consume_skb_irq(il->beacon_skb);
 	il->beacon_skb = NULL;
 	il->timestamp = 0;
 
@@ -5292,7 +5294,7 @@
 	}
 
 	spin_lock_irqsave(&il->lock, flags);
-	dev_kfree_skb(il->beacon_skb);
+	dev_consume_skb_irq(il->beacon_skb);
 	il->beacon_skb = skb;
 
 	timestamp = ((struct ieee80211_mgmt *)skb->data)->u.beacon.timestamp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c
@@ -304,7 +304,7 @@
 
 	priv->is_open = 1;
 	IWL_DEBUG_MAC80211(priv, "leave\n");
-	return 0;
+	return ret;
 }
 
 static void iwlagn_mac_stop(struct ieee80211_hw *hw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/dvm/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/dvm/main.c
@@ -1525,7 +1525,6 @@
 	kfree(priv->nvm_data);
 
 	/*netif_stop_queue(dev); */
-	flush_workqueue(priv->workqueue);
 
 	/* ieee80211_unregister_hw calls iwlagn_mac_stop, which flushes
 	 * priv->workqueue... so we can't take down the workqueue
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/dvm/rs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/dvm/rs.c
@@ -130,7 +130,7 @@
 				return idx;
 	}
 
-	return -1;
+	return IWL_RATE_INVALID;
 }
 
 static void rs_rate_scale_perform(struct iwl_priv *priv,
@@ -3151,7 +3151,10 @@
 	for (i = 0; i < LINK_QUAL_MAX_RETRY_NUM; i++) {
 		index = iwl_hwrate_to_plcp_idx(
 			le32_to_cpu(lq_sta->lq.rs_table[i].rate_n_flags));
-		if (is_legacy(tbl->lq_type)) {
+		if (index == IWL_RATE_INVALID) {
+			desc += sprintf(buff + desc, " rate[%d] 0x%X invalid rate\n",
+				i, le32_to_cpu(lq_sta->lq.rs_table[i].rate_n_flags));
+		} else if (is_legacy(tbl->lq_type)) {
 			desc += sprintf(buff+desc, " rate[%d] 0x%X %smbps\n",
 				i, le32_to_cpu(lq_sta->lq.rs_table[i].rate_n_flags),
 				iwl_rate_mcs[index].mbps);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/dvm/sta.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/dvm/sta.c
@@ -1086,6 +1086,7 @@
 {
 	__le16 key_flags;
 	struct iwl_addsta_cmd sta_cmd;
+	size_t to_copy;
 	int i;
 
 	spin_lock_bh(&priv->sta_lock);
@@ -1105,7 +1106,9 @@
 		sta_cmd.key.tkip_rx_tsc_byte2 = tkip_iv32;
 		for (i = 0; i < 5; i++)
 			sta_cmd.key.tkip_rx_ttak[i] = cpu_to_le16(tkip_p1k[i]);
-		memcpy(sta_cmd.key.key, keyconf->key, keyconf->keylen);
+		/* keyconf may contain MIC rx/tx keys which iwl does not use */
+		to_copy = min_t(size_t, sizeof(sta_cmd.key.key), keyconf->keylen);
+		memcpy(sta_cmd.key.key, keyconf->key, to_copy);
 		break;
 	case WLAN_CIPHER_SUITE_WEP104:
 		key_flags |= STA_KEY_FLG_KEY_SIZE_MSK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/dvm/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/dvm/tx.c
@@ -3,6 +3,7 @@
  *
  * Copyright(c) 2008 - 2014 Intel Corporation. All rights reserved.
  * Copyright (C) 2019 Intel Corporation
+ * Copyright (C) 2023 Intel Corporation
  *
  * Contact Information:
  *  Intel Linux Wireless <linuxwifi@intel.com>
@@ -1174,7 +1175,7 @@
 			iwlagn_check_ratid_empty(priv, sta_id, tid);
 		}
 
-		iwl_trans_reclaim(priv->trans, txq_id, ssn, &skbs);
+		iwl_trans_reclaim(priv->trans, txq_id, ssn, &skbs, false);
 
 		freed = 0;
 
@@ -1320,7 +1321,7 @@
 	 * block-ack window (we assume that they've been successfully
 	 * transmitted ... if not, it's too late anyway). */
 	iwl_trans_reclaim(priv->trans, scd_flow, ba_resp_scd_ssn,
-			  &reclaimed_skbs);
+			  &reclaimed_skbs, false);
 
 	IWL_DEBUG_TX_REPLY(priv, "REPLY_COMPRESSED_BA [%d] Received from %pM, "
 			   "sta_id = %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/acpi.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
 /*
  * Copyright (C) 2017 Intel Deutschland GmbH
- * Copyright (C) 2019-2021 Intel Corporation
+ * Copyright (C) 2019-2022 Intel Corporation
  */
 #include <linux/uuid.h>
 #include "iwl-drv.h"
@@ -98,7 +98,7 @@
 				    size_t expected_size)
 {
 	union acpi_object *obj;
-	int ret = 0;
+	int ret;
 
 	obj = iwl_acpi_get_dsm_object(dev, rev, func, NULL, guid);
 	if (IS_ERR(obj)) {
@@ -113,8 +113,10 @@
 	} else if (obj->type == ACPI_TYPE_BUFFER) {
 		__le64 le_value = 0;
 
-		if (WARN_ON_ONCE(expected_size > sizeof(le_value)))
-			return -EINVAL;
+		if (WARN_ON_ONCE(expected_size > sizeof(le_value))) {
+			ret = -EINVAL;
+			goto out;
+		}
 
 		/* if the buffer size doesn't match the expected size */
 		if (obj->buffer.length != expected_size)
@@ -135,8 +137,9 @@
 	}
 
 	IWL_DEBUG_DEV_RADIO(dev,
-			    "ACPI: DSM method evaluated: func=%d, ret=%d\n",
-			    func, ret);
+			    "ACPI: DSM method evaluated: func=%d, value=%lld\n",
+			    func, *value);
+	ret = 0;
 out:
 	ACPI_FREE(obj);
 	return ret;
@@ -527,7 +530,7 @@
 					 &tbl_rev);
 	if (!IS_ERR(wifi_pkg)) {
 		if (tbl_rev != 2) {
-			ret = PTR_ERR(wifi_pkg);
+			ret = -EINVAL;
 			goto out_free;
 		}
 
@@ -543,7 +546,7 @@
 					 &tbl_rev);
 	if (!IS_ERR(wifi_pkg)) {
 		if (tbl_rev != 1) {
-			ret = PTR_ERR(wifi_pkg);
+			ret = -EINVAL;
 			goto out_free;
 		}
 
@@ -559,7 +562,7 @@
 					 &tbl_rev);
 	if (!IS_ERR(wifi_pkg)) {
 		if (tbl_rev != 0) {
-			ret = PTR_ERR(wifi_pkg);
+			ret = -EINVAL;
 			goto out_free;
 		}
 
@@ -614,7 +617,7 @@
 					 &tbl_rev);
 	if (!IS_ERR(wifi_pkg)) {
 		if (tbl_rev != 2) {
-			ret = PTR_ERR(wifi_pkg);
+			ret = -EINVAL;
 			goto out_free;
 		}
 
@@ -630,7 +633,7 @@
 					 &tbl_rev);
 	if (!IS_ERR(wifi_pkg)) {
 		if (tbl_rev != 1) {
-			ret = PTR_ERR(wifi_pkg);
+			ret = -EINVAL;
 			goto out_free;
 		}
 
@@ -646,7 +649,7 @@
 					 &tbl_rev);
 	if (!IS_ERR(wifi_pkg)) {
 		if (tbl_rev != 0) {
-			ret = PTR_ERR(wifi_pkg);
+			ret = -EINVAL;
 			goto out_free;
 		}
 
@@ -674,7 +677,7 @@
 	 * from index 1, so the maximum value allowed here is
 	 * ACPI_SAR_PROFILES_NUM - 1.
 	 */
-	if (n_profiles <= 0 || n_profiles >= ACPI_SAR_PROFILE_NUM) {
+	if (n_profiles >= ACPI_SAR_PROFILE_NUM) {
 		ret = -EINVAL;
 		goto out_free;
 	}
@@ -814,10 +817,11 @@
 	 * only one using version 36, so skip this version entirely.
 	 */
 	return IWL_UCODE_SERIAL(fwrt->fw->ucode_ver) >= 38 ||
-	       IWL_UCODE_SERIAL(fwrt->fw->ucode_ver) == 17 ||
-	       (IWL_UCODE_SERIAL(fwrt->fw->ucode_ver) == 29 &&
-		((fwrt->trans->hw_rev & CSR_HW_REV_TYPE_MSK) ==
-		 CSR_HW_REV_TYPE_7265D));
+		(IWL_UCODE_SERIAL(fwrt->fw->ucode_ver) == 17 &&
+		 fwrt->trans->hw_rev != CSR_HW_REV_TYPE_3160) ||
+		(IWL_UCODE_SERIAL(fwrt->fw->ucode_ver) == 29 &&
+		 ((fwrt->trans->hw_rev & CSR_HW_REV_TYPE_MSK) ==
+		  CSR_HW_REV_TYPE_7265D));
 }
 IWL_EXPORT_SYMBOL(iwl_sar_geo_support);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/dbg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/dbg.c
@@ -558,41 +558,71 @@
 }
 
 /*
- * alloc_sgtable - allocates scallerlist table in the given size,
- * fills it with pages and returns it
+ * alloc_sgtable - allocates (chained) scatterlist in the given size,
+ *	fills it with pages and returns it
  * @size: the size (in bytes) of the table
-*/
-static struct scatterlist *alloc_sgtable(int size)
+ */
+static struct scatterlist *alloc_sgtable(ssize_t size)
 {
-	int alloc_size, nents, i;
-	struct page *new_page;
-	struct scatterlist *iter;
-	struct scatterlist *table;
+	struct scatterlist *result = NULL, *prev;
+	int nents, i, n_prev;
 
 	nents = DIV_ROUND_UP(size, PAGE_SIZE);
-	table = kcalloc(nents, sizeof(*table), GFP_KERNEL);
-	if (!table)
-		return NULL;
-	sg_init_table(table, nents);
-	iter = table;
-	for_each_sg(table, iter, sg_nents(table), i) {
-		new_page = alloc_page(GFP_KERNEL);
-		if (!new_page) {
-			/* release all previous allocated pages in the table */
-			iter = table;
-			for_each_sg(table, iter, sg_nents(table), i) {
-				new_page = sg_page(iter);
-				if (new_page)
-					__free_page(new_page);
-			}
-			kfree(table);
+
+#define N_ENTRIES_PER_PAGE (PAGE_SIZE / sizeof(*result))
+	/*
+	 * We need an additional entry for table chaining,
+	 * this ensures the loop can finish i.e. we can
+	 * fit at least two entries per page (obviously,
+	 * many more really fit.)
+	 */
+	BUILD_BUG_ON(N_ENTRIES_PER_PAGE < 2);
+
+	while (nents > 0) {
+		struct scatterlist *new, *iter;
+		int n_fill, n_alloc;
+
+		if (nents <= N_ENTRIES_PER_PAGE) {
+			/* last needed table */
+			n_fill = nents;
+			n_alloc = nents;
+			nents = 0;
+		} else {
+			/* fill a page with entries */
+			n_alloc = N_ENTRIES_PER_PAGE;
+			/* reserve one for chaining */
+			n_fill = n_alloc - 1;
+			nents -= n_fill;
+		}
+
+		new = kcalloc(n_alloc, sizeof(*new), GFP_KERNEL);
+		if (!new) {
+			if (result)
+				_devcd_free_sgtable(result);
 			return NULL;
 		}
-		alloc_size = min_t(int, size, PAGE_SIZE);
-		size -= PAGE_SIZE;
-		sg_set_page(iter, new_page, alloc_size, 0);
+		sg_init_table(new, n_alloc);
+
+		if (!result)
+			result = new;
+		else
+			sg_chain(prev, n_prev, new);
+		prev = new;
+		n_prev = n_alloc;
+
+		for_each_sg(new, iter, n_fill, i) {
+			struct page *new_page = alloc_page(GFP_KERNEL);
+
+			if (!new_page) {
+				_devcd_free_sgtable(result);
+				return NULL;
+			}
+
+			sg_set_page(iter, new_page, PAGE_SIZE, 0);
+		}
 	}
-	return table;
+
+	return result;
 }
 
 static void iwl_fw_get_prph_len(struct iwl_fw_runtime *fwrt,
@@ -1022,7 +1052,7 @@
 	range->range_data_size = reg->dev_addr.size;
 	for (i = 0; i < le32_to_cpu(reg->dev_addr.size); i += 4) {
 		prph_val = iwl_read_prph(fwrt->trans, addr + i);
-		if (prph_val == 0x5a5a5a5a)
+		if ((prph_val & ~0xf) == 0xa5a5a5a0)
 			return -EBUSY;
 		*val++ = cpu_to_le32(prph_val);
 	}
@@ -1362,13 +1392,13 @@
 	if (!data)
 		return;
 
+	memset(data, 0, sizeof(*data));
+
 	/* make sure only one bit is set in only one fid */
 	if (WARN_ONCE(hweight_long(fid1) + hweight_long(fid2) != 1,
 		      "fid1=%x, fid2=%x\n", fid1, fid2))
 		return;
 
-	memset(data, 0, sizeof(*data));
-
 	if (fid1) {
 		fifo_idx = ffs(fid1) - 1;
 		if (WARN_ONCE(fifo_idx >= MAX_NUM_LMAC, "fifo_idx=%d\n",
@@ -1532,13 +1562,11 @@
 		return -EBUSY;
 
 	range->range_data_size = reg->dev_addr.size;
-	iwl_write_prph_no_grab(fwrt->trans, DBGI_SRAM_TARGET_ACCESS_CFG,
-			       DBGI_SRAM_TARGET_ACCESS_CFG_RESET_ADDRESS_MSK);
 	for (i = 0; i < (le32_to_cpu(reg->dev_addr.size) / 4); i++) {
 		prph_data = iwl_read_prph(fwrt->trans, (i % 2) ?
 					  DBGI_SRAM_TARGET_ACCESS_RDATA_MSB :
 					  DBGI_SRAM_TARGET_ACCESS_RDATA_LSB);
-		if (prph_data == 0x5a5a5a5a) {
+		if ((prph_data & ~0xf) == 0xa5a5a5a0) {
 			iwl_trans_release_nic_access(fwrt->trans);
 			return -EBUSY;
 		}
@@ -1962,7 +1990,7 @@
 	struct iwl_fw_ini_error_dump_header *header;
 	u32 type = le32_to_cpu(reg->type), id = le32_to_cpu(reg->id);
 	u32 num_of_ranges, i, size;
-	void *range;
+	u8 *range;
 
 	/*
 	 * The higher part of the ID in version 2 is irrelevant for
@@ -2864,7 +2892,7 @@
 {
 	int ret __maybe_unused = 0;
 
-	if (test_bit(STATUS_FW_ERROR, &fwrt->trans->status))
+	if (!iwl_trans_fw_running(fwrt->trans))
 		return;
 
 	if (fw_has_capa(&fwrt->fw->ucode_capa,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/debugfs.c
@@ -163,7 +163,11 @@
 
 	event_cfg.enabled_severities = cpu_to_le32(enabled_severities);
 
-	ret = iwl_trans_send_cmd(fwrt->trans, &hcmd);
+	if (fwrt->ops && fwrt->ops->send_hcmd)
+		ret = fwrt->ops->send_hcmd(fwrt->ops_ctx, &hcmd);
+	else
+		ret = -EPERM;
+
 	IWL_INFO(fwrt,
 		 "sent host event cfg with enabled_severities: %u, ret: %d\n",
 		 enabled_severities, ret);
@@ -248,8 +252,7 @@
 		.data = { NULL, },
 	};
 
-	if (fwrt->ops && fwrt->ops->fw_running &&
-	    !fwrt->ops->fw_running(fwrt->ops_ctx))
+	if (!iwl_trans_fw_running(fwrt->trans))
 		return -EIO;
 
 	if (count < header_size + 1 || count > 1024 * 4)
@@ -317,8 +320,10 @@
 	const struct iwl_fw *fw = priv->fwrt->fw;
 
 	*pos = ++state->pos;
-	if (*pos >= fw->ucode_capa.n_cmd_versions)
+	if (*pos >= fw->ucode_capa.n_cmd_versions) {
+		kfree(state);
 		return NULL;
+	}
 
 	return state;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/error-dump.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/error-dump.h
@@ -277,9 +277,9 @@
 struct iwl_fw_ini_error_dump_range {
 	__le32 range_data_size;
 	union {
-		__le32 internal_base_addr;
-		__le64 dram_base_addr;
-		__le32 page_num;
+		__le32 internal_base_addr __packed;
+		__le64 dram_base_addr __packed;
+		__le32 page_num __packed;
 		struct iwl_fw_ini_fifo_hdr fifo_hdr;
 		struct iwl_cmd_header fw_pkt_hdr;
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/init.c
@@ -35,10 +35,12 @@
 }
 IWL_EXPORT_SYMBOL(iwl_fw_runtime_init);
 
+/* Assumes the appropriate lock is held by the caller */
 void iwl_fw_runtime_suspend(struct iwl_fw_runtime *fwrt)
 {
 	iwl_fw_suspend_timestamp(fwrt);
-	iwl_dbg_tlv_time_point(fwrt, IWL_FW_INI_TIME_POINT_HOST_D3_START, NULL);
+	iwl_dbg_tlv_time_point_sync(fwrt, IWL_FW_INI_TIME_POINT_HOST_D3_START,
+				    NULL);
 }
 IWL_EXPORT_SYMBOL(iwl_fw_runtime_suspend);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/pnvm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/pnvm.c
@@ -284,16 +284,19 @@
 	/* First attempt to get the PNVM from BIOS */
 	package = iwl_uefi_get_pnvm(trans, &len);
 	if (!IS_ERR_OR_NULL(package)) {
-		data = kmemdup(package->data, len, GFP_KERNEL);
+		if (len >= sizeof(*package)) {
+			/* we need only the data */
+			len -= sizeof(*package);
+			data = kmemdup(package->data, len, GFP_KERNEL);
+		} else {
+			data = NULL;
+		}
 
 		/* free package regardless of whether kmemdup succeeded */
 		kfree(package);
 
-		if (data) {
-			/* we need only the data size */
-			len -= sizeof(*package);
+		if (data)
 			goto parse;
-		}
 	}
 
 	/* If it's not available, try from the filesystem */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/runtime.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/runtime.h
@@ -18,7 +18,6 @@
 struct iwl_fw_runtime_ops {
 	int (*dump_start)(void *ctx);
 	void (*dump_end)(void *ctx);
-	bool (*fw_running)(void *ctx);
 	int (*send_hcmd)(void *ctx, struct iwl_host_cmd *host_cmd);
 	bool (*d3_debug_enable)(void *ctx);
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/uefi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/uefi.c
@@ -86,6 +86,7 @@
 		if (len < tlv_len) {
 			IWL_ERR(trans, "invalid TLV len: %zd/%u\n",
 				len, tlv_len);
+			kfree(reduce_power_data);
 			reduce_power_data = ERR_PTR(-EINVAL);
 			goto out;
 		}
@@ -105,6 +106,7 @@
 				IWL_DEBUG_FW(trans,
 					     "Couldn't allocate (more) reduce_power_data\n");
 
+				kfree(reduce_power_data);
 				reduce_power_data = ERR_PTR(-ENOMEM);
 				goto out;
 			}
@@ -134,6 +136,10 @@
 done:
 	if (!size) {
 		IWL_DEBUG_FW(trans, "Empty REDUCE_POWER, skipping.\n");
+		/* Better safe than sorry, but 'reduce_power_data' should
+		 * always be NULL if !size.
+		 */
+		kfree(reduce_power_data);
 		reduce_power_data = ERR_PTR(-ENOENT);
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/fw/uefi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/fw/uefi.h
@@ -2,7 +2,8 @@
 /*
  * Copyright(c) 2021 Intel Corporation
  */
-
+#ifndef __iwl_fw_uefi__
+#define __iwl_fw_uefi__
 
 #define IWL_UEFI_OEM_PNVM_NAME		L"UefiCnvWlanOemSignedPnvm"
 #define IWL_UEFI_REDUCED_POWER_NAME	L"UefiCnvWlanReducedPower"
@@ -40,3 +41,5 @@
 	return ERR_PTR(-EOPNOTSUPP);
 }
 #endif /* CONFIG_EFI */
+
+#endif /* __iwl_fw_uefi__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-csr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-csr.h
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
- * Copyright (C) 2005-2014, 2018-2021 Intel Corporation
+ * Copyright (C) 2005-2014, 2018-2022 Intel Corporation
  * Copyright (C) 2013-2014 Intel Mobile Communications GmbH
  * Copyright (C) 2016 Intel Deutschland GmbH
  */
@@ -104,9 +104,10 @@
 /* GIO Chicken Bits (PCI Express bus link power management) */
 #define CSR_GIO_CHICKEN_BITS    (CSR_BASE+0x100)
 
-/* Doorbell NMI (since Bz) */
+/* Doorbell - since Bz
+ * connected to UREG_DOORBELL_TO_ISR6 (lower 16 bits only)
+ */
 #define CSR_DOORBELL_VECTOR	(CSR_BASE + 0x130)
-#define CSR_DOORBELL_VECTOR_NMI	BIT(1)
 
 /* host chicken bits */
 #define CSR_HOST_CHICKEN	(CSR_BASE + 0x204)
@@ -318,6 +319,7 @@
 #define CSR_HW_REV_TYPE_2x00		(0x0000100)
 #define CSR_HW_REV_TYPE_105		(0x0000110)
 #define CSR_HW_REV_TYPE_135		(0x0000120)
+#define CSR_HW_REV_TYPE_3160		(0x0000164)
 #define CSR_HW_REV_TYPE_7265D		(0x0000210)
 #define CSR_HW_REV_TYPE_NONE		(0x00001F0)
 #define CSR_HW_REV_TYPE_QNJ		(0x0000360)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-dbg-tlv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-dbg-tlv.c
@@ -99,6 +99,12 @@
 	if (le32_to_cpu(tlv->length) != sizeof(*debug_info))
 		return -EINVAL;
 
+	/* we use this as a string, ensure input was NUL terminated */
+	if (strnlen(debug_info->debug_cfg_name,
+		    sizeof(debug_info->debug_cfg_name)) ==
+			sizeof(debug_info->debug_cfg_name))
+		return -EINVAL;
+
 	IWL_DEBUG_FW(trans, "WRT: Loading debug cfg: %s\n",
 		     debug_info->debug_cfg_name);
 
@@ -134,6 +140,12 @@
 	    alloc_id != IWL_FW_INI_ALLOCATION_ID_DBGC1)
 		goto err;
 
+	if (buf_location == IWL_FW_INI_LOCATION_DRAM_PATH &&
+	    alloc->req_size == 0) {
+		IWL_ERR(trans, "WRT: Invalid DRAM buffer allocation requested size (0)\n");
+		return -EINVAL;
+	}
+
 	trans->dbg.fw_mon_cfg[alloc_id] = *alloc;
 
 	return 0;
@@ -322,7 +334,7 @@
 	struct iwl_dbg_tlv_timer_node *node, *tmp;
 
 	list_for_each_entry_safe(node, tmp, timer_list, list) {
-		del_timer(&node->timer);
+		del_timer_sync(&node->timer);
 		list_del(&node->list);
 		kfree(node);
 	}
@@ -830,7 +842,7 @@
 		node_trig = (void *)node_tlv->data;
 	}
 
-	memcpy(node_trig->data + offset, trig->data, trig_data_len);
+	memcpy((u8 *)node_trig->data + offset, trig->data, trig_data_len);
 	node_tlv->length = cpu_to_le32(size);
 
 	if (policy & IWL_FW_INI_APPLY_POLICY_OVERRIDE_CFG) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-drv.c
@@ -131,6 +131,9 @@
 
 	for (i = 0; i < IWL_UCODE_TYPE_MAX; i++)
 		iwl_free_fw_img(drv, drv->fw.img + i);
+
+	/* clear the data for the aborted load case */
+	memset(&drv->fw, 0, sizeof(drv->fw));
 }
 
 static int iwl_alloc_fw_desc(struct iwl_drv *drv, struct fw_desc *desc,
@@ -1068,7 +1071,7 @@
 
 			if (tlv_len != sizeof(*fseq_ver))
 				goto invalid_tlv_len;
-			IWL_INFO(drv, "TLV_FW_FSEQ_VERSION: %s\n",
+			IWL_INFO(drv, "TLV_FW_FSEQ_VERSION: %.32s\n",
 				 fseq_ver->version);
 			}
 			break;
@@ -1271,23 +1274,31 @@
 	const struct iwl_op_mode_ops *ops = op->ops;
 	struct dentry *dbgfs_dir = NULL;
 	struct iwl_op_mode *op_mode = NULL;
+	int retry, max_retry = !!iwlwifi_mod_params.fw_restart * IWL_MAX_INIT_RETRY;
+
+	for (retry = 0; retry <= max_retry; retry++) {
 
 #ifdef CONFIG_IWLWIFI_DEBUGFS
-	drv->dbgfs_op_mode = debugfs_create_dir(op->name,
-						drv->dbgfs_drv);
-	dbgfs_dir = drv->dbgfs_op_mode;
+		drv->dbgfs_op_mode = debugfs_create_dir(op->name,
+							drv->dbgfs_drv);
+		dbgfs_dir = drv->dbgfs_op_mode;
 #endif
 
-	op_mode = ops->start(drv->trans, drv->trans->cfg, &drv->fw, dbgfs_dir);
+		op_mode = ops->start(drv->trans, drv->trans->cfg,
+				     &drv->fw, dbgfs_dir);
+
+		if (op_mode)
+			return op_mode;
+
+		IWL_ERR(drv, "retry init count %d\n", retry);
 
 #ifdef CONFIG_IWLWIFI_DEBUGFS
-	if (!op_mode) {
 		debugfs_remove_recursive(drv->dbgfs_op_mode);
 		drv->dbgfs_op_mode = NULL;
-	}
 #endif
+	}
 
-	return op_mode;
+	return NULL;
 }
 
 static void _iwl_op_mode_stop(struct iwl_drv *drv)
@@ -1325,6 +1336,7 @@
 	int i;
 	bool load_module = false;
 	bool usniffer_images = false;
+	bool failure = true;
 
 	fw->ucode_capa.max_probe_length = IWL_DEFAULT_MAX_PROBE_LENGTH;
 	fw->ucode_capa.standard_phy_calibration_size =
@@ -1585,15 +1597,9 @@
 	 * else from proceeding if the module fails to load
 	 * or hangs loading.
 	 */
-	if (load_module) {
+	if (load_module)
 		request_module("%s", op->name);
-#ifdef CONFIG_IWLWIFI_OPMODE_MODULAR
-		if (err)
-			IWL_ERR(drv,
-				"failed to load module %s (error %d), is dynamic loading enabled?\n",
-				op->name, err);
-#endif
-	}
+	failure = false;
 	goto free;
 
  try_again:
@@ -1608,7 +1614,12 @@
  out_unbind:
 	complete(&drv->request_firmware_complete);
 	device_release_driver(drv->trans->dev);
+	/* drv has just been freed by the release */
+	failure = false;
  free:
+	if (failure)
+		iwl_dealloc_ucode(drv);
+
 	if (pieces) {
 		for (i = 0; i < ARRAY_SIZE(pieces->img); i++)
 			kfree(pieces->img[i].sec);
@@ -1656,8 +1667,8 @@
 err_fw:
 #ifdef CONFIG_IWLWIFI_DEBUGFS
 	debugfs_remove_recursive(drv->dbgfs_drv);
-	iwl_dbg_tlv_free(drv->trans);
 #endif
+	iwl_dbg_tlv_free(drv->trans);
 	kfree(drv);
 err:
 	return ERR_PTR(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-drv.h
@@ -90,4 +90,7 @@
 #define IWL_EXPORT_SYMBOL(sym)
 #endif
 
+/* max retry for init flow */
+#define IWL_MAX_INIT_RETRY 2
+
 #endif /* __iwl_drv_h__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-io.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-io.c
@@ -218,7 +218,7 @@
 				    UREG_DOORBELL_TO_ISR6_NMI_BIT);
 	else
 		iwl_write32(trans, CSR_DOORBELL_VECTOR,
-			    CSR_DOORBELL_VECTOR_NMI);
+			    UREG_DOORBELL_TO_ISR6_NMI_BIT);
 }
 IWL_EXPORT_SYMBOL(iwl_force_nmi);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
@@ -541,8 +541,7 @@
 			.has_he = true,
 			.he_cap_elem = {
 				.mac_cap_info[0] =
-					IEEE80211_HE_MAC_CAP0_HTC_HE |
-					IEEE80211_HE_MAC_CAP0_TWT_REQ,
+					IEEE80211_HE_MAC_CAP0_HTC_HE,
 				.mac_cap_info[1] =
 					IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US |
 					IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-prph.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-prph.h
@@ -350,8 +350,6 @@
 #define WFPM_GP2			0xA030B4
 
 /* DBGI SRAM Register details */
-#define DBGI_SRAM_TARGET_ACCESS_CFG			0x00A2E14C
-#define DBGI_SRAM_TARGET_ACCESS_CFG_RESET_ADDRESS_MSK	0x10000
 #define DBGI_SRAM_TARGET_ACCESS_RDATA_LSB		0x00A2E154
 #define DBGI_SRAM_TARGET_ACCESS_RDATA_MSB		0x00A2E158
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/iwl-trans.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/iwl-trans.h
@@ -539,7 +539,7 @@
 	int (*tx)(struct iwl_trans *trans, struct sk_buff *skb,
 		  struct iwl_device_tx_cmd *dev_cmd, int queue);
 	void (*reclaim)(struct iwl_trans *trans, int queue, int ssn,
-			struct sk_buff_head *skbs);
+			struct sk_buff_head *skbs, bool is_flush);
 
 	void (*set_q_ptrs)(struct iwl_trans *trans, int queue, int ptr);
 
@@ -1122,14 +1122,15 @@
 }
 
 static inline void iwl_trans_reclaim(struct iwl_trans *trans, int queue,
-				     int ssn, struct sk_buff_head *skbs)
+				     int ssn, struct sk_buff_head *skbs,
+				     bool is_flush)
 {
 	if (WARN_ON_ONCE(trans->state != IWL_TRANS_FW_ALIVE)) {
 		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
 		return;
 	}
 
-	trans->ops->reclaim(trans, queue, ssn, skbs);
+	trans->ops->reclaim(trans, queue, ssn, skbs, is_flush);
 }
 
 static inline void iwl_trans_set_q_ptrs(struct iwl_trans *trans, int queue,
@@ -1392,8 +1393,8 @@
 
 	/* prevent double restarts due to the same erroneous FW */
 	if (!test_and_set_bit(STATUS_FW_ERROR, &trans->status)) {
-		iwl_op_mode_nic_error(trans->op_mode, sync);
 		trans->state = IWL_TRANS_NO_FW;
+		iwl_op_mode_nic_error(trans->op_mode, sync);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/constants.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/constants.h
@@ -103,7 +103,7 @@
 #define IWL_MVM_FTM_INITIATOR_SECURE_LTF	false
 #define IWL_MVM_FTM_RESP_NDP_SUPPORT		true
 #define IWL_MVM_FTM_RESP_LMR_FEEDBACK_SUPPORT	true
-#define IWL_MVM_FTM_NON_TB_MIN_TIME_BETWEEN_MSR	5
+#define IWL_MVM_FTM_NON_TB_MIN_TIME_BETWEEN_MSR	7
 #define IWL_MVM_FTM_NON_TB_MAX_TIME_BETWEEN_MSR	1000
 #define IWL_MVM_D3_DEBUG			false
 #define IWL_MVM_USE_TWT				true
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/d3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/d3.c
@@ -462,12 +462,10 @@
 		struct wowlan_key_rsc_v5_data data = {};
 		int i;
 
-		data.rsc = kmalloc(sizeof(*data.rsc), GFP_KERNEL);
+		data.rsc = kzalloc(sizeof(*data.rsc), GFP_KERNEL);
 		if (!data.rsc)
 			return -ENOMEM;
 
-		memset(data.rsc, 0xff, sizeof(*data.rsc));
-
 		for (i = 0; i < ARRAY_SIZE(data.rsc->mcast_key_id_map); i++)
 			data.rsc->mcast_key_id_map[i] =
 				IWL_MCAST_KEY_MAP_INVALID;
@@ -564,6 +562,7 @@
 		}
 
 		for (i = 0; i < IWL_NUM_RSC; i++) {
+			ieee80211_get_key_rx_seq(key, i, &seq);
 			/* wrapping isn't allowed, AP must rekey */
 			if (seq.tkip.iv32 > cur_rx_iv32)
 				cur_rx_iv32 = seq.tkip.iv32;
@@ -596,16 +595,25 @@
 					 void *_data)
 {
 	struct wowlan_key_gtk_type_iter *data = _data;
+	__le32 *cipher = NULL;
+
+	if (key->keyidx == 4 || key->keyidx == 5)
+		cipher = &data->kek_kck_cmd->igtk_cipher;
+	if (key->keyidx == 6 || key->keyidx == 7)
+		cipher = &data->kek_kck_cmd->bigtk_cipher;
 
 	switch (key->cipher) {
 	default:
 		return;
 	case WLAN_CIPHER_SUITE_BIP_GMAC_256:
 	case WLAN_CIPHER_SUITE_BIP_GMAC_128:
-		data->kek_kck_cmd->igtk_cipher = cpu_to_le32(STA_KEY_FLG_GCMP);
+		if (cipher)
+			*cipher = cpu_to_le32(STA_KEY_FLG_GCMP);
 		return;
 	case WLAN_CIPHER_SUITE_AES_CMAC:
-		data->kek_kck_cmd->igtk_cipher = cpu_to_le32(STA_KEY_FLG_CCM);
+	case WLAN_CIPHER_SUITE_BIP_CMAC_256:
+		if (cipher)
+			*cipher = cpu_to_le32(STA_KEY_FLG_CCM);
 		return;
 	case WLAN_CIPHER_SUITE_CCMP:
 		if (!sta)
@@ -1089,7 +1097,7 @@
 					sizeof(struct iwl_wowlan_kek_kck_material_cmd_v2);
 			/* skip the sta_id at the beginning */
 			_kek_kck_cmd = (void *)
-				((u8 *)_kek_kck_cmd) + sizeof(kek_kck_cmd.sta_id);
+				((u8 *)_kek_kck_cmd + sizeof(kek_kck_cmd.sta_id));
 		}
 
 		IWL_DEBUG_WOWLAN(mvm, "setting akm %d\n",
@@ -1372,7 +1380,9 @@
 
 	iwl_mvm_pause_tcm(mvm, true);
 
+	mutex_lock(&mvm->mutex);
 	iwl_fw_runtime_suspend(&mvm->fwrt);
+	mutex_unlock(&mvm->mutex);
 
 	return __iwl_mvm_suspend(hw, wowlan, false);
 }
@@ -1797,7 +1807,8 @@
 
 out:
 	if (iwl_fw_lookup_notif_ver(mvm->fw, LONG_GROUP,
-				    WOWLAN_GET_STATUSES, 0) < 10) {
+				    WOWLAN_GET_STATUSES,
+				    IWL_FW_CMD_VER_UNKNOWN) < 10) {
 		mvmvif->seqno_valid = true;
 		/* +0x10 because the set API expects next-to-use, not last-used */
 		mvmvif->seqno = le16_to_cpu(status->non_qos_seq_ctr) + 0x10;
@@ -2336,7 +2347,6 @@
 		iwl_fw_dbg_collect_desc(&mvm->fwrt, &iwl_dump_desc_assert,
 					false, 0);
 		ret = 1;
-		mvm->trans->system_pm_mode = IWL_PLAT_PM_MODE_DISABLED;
 		goto err;
 	}
 
@@ -2385,6 +2395,7 @@
 		}
 	}
 
+	/* after the successful handshake, we're out of D3 */
 	mvm->trans->system_pm_mode = IWL_PLAT_PM_MODE_DISABLED;
 
 	/*
@@ -2455,6 +2466,9 @@
 	 */
 	set_bit(IWL_MVM_STATUS_HW_RESTART_REQUESTED, &mvm->status);
 
+	/* regardless of what happened, we're now out of D3 */
+	mvm->trans->system_pm_mode = IWL_PLAT_PM_MODE_DISABLED;
+
 	return 1;
 }
 
@@ -2496,7 +2510,9 @@
 
 	/* start pseudo D3 */
 	rtnl_lock();
+	wiphy_lock(mvm->hw->wiphy);
 	err = __iwl_mvm_suspend(mvm->hw, mvm->hw->wiphy->wowlan_config, true);
+	wiphy_unlock(mvm->hw->wiphy);
 	rtnl_unlock();
 	if (err > 0)
 		err = -EINVAL;
@@ -2552,7 +2568,9 @@
 	iwl_fw_dbg_read_d3_debug_data(&mvm->fwrt);
 
 	rtnl_lock();
+	wiphy_lock(mvm->hw->wiphy);
 	__iwl_mvm_resume(mvm, true);
+	wiphy_unlock(mvm->hw->wiphy);
 	rtnl_unlock();
 
 	iwl_mvm_resume_tcm(mvm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c
@@ -5,6 +5,7 @@
  * Copyright (C) 2016-2017 Intel Deutschland GmbH
  */
 #include <linux/vmalloc.h>
+#include <linux/err.h>
 #include <linux/ieee80211.h>
 #include <linux/netdevice.h>
 
@@ -1930,6 +1931,11 @@
 	if (ret < 0)
 		return ret;
 
+	if (iwl_rx_packet_payload_len(hcmd.resp_pkt) < sizeof(*rsp)) {
+		ret = -EIO;
+		goto out;
+	}
+
 	rsp = (void *)hcmd.resp_pkt->data;
 	if (le32_to_cpu(rsp->status) != DEBUG_MEM_STATUS_SUCCESS) {
 		ret = -ENXIO;
@@ -1944,7 +1950,7 @@
 		goto out;
 	}
 
-	ret = len - copy_to_user(user_buf, (void *)rsp->data + delta, len);
+	ret = len - copy_to_user(user_buf, (u8 *)rsp->data + delta, len);
 	*ppos += ret;
 
 out:
@@ -2007,6 +2013,11 @@
 	if (ret < 0)
 		return ret;
 
+	if (iwl_rx_packet_payload_len(hcmd.resp_pkt) < sizeof(*rsp)) {
+		ret = -EIO;
+		goto out;
+	}
+
 	rsp = (void *)hcmd.resp_pkt->data;
 	if (rsp->status != DEBUG_MEM_STATUS_SUCCESS) {
 		ret = -ENXIO;
@@ -2044,7 +2055,6 @@
 void iwl_mvm_dbgfs_register(struct iwl_mvm *mvm)
 {
 	struct dentry *bcast_dir __maybe_unused;
-	char buf[100];
 
 	spin_lock_init(&mvm->drv_stats_lock);
 
@@ -2140,6 +2150,11 @@
 	 * Create a symlink with mac80211. It will be removed when mac80211
 	 * exists (before the opmode exists which removes the target.)
 	 */
-	snprintf(buf, 100, "../../%pd2", mvm->debugfs_dir->d_parent);
-	debugfs_create_symlink("iwlwifi", mvm->hw->wiphy->debugfsdir, buf);
+	if (!IS_ERR(mvm->debugfs_dir)) {
+		char buf[100];
+
+		snprintf(buf, 100, "../../%pd2", mvm->debugfs_dir->d_parent);
+		debugfs_create_symlink("iwlwifi", mvm->hw->wiphy->debugfsdir,
+				       buf);
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c
@@ -48,6 +48,8 @@
 	if (!pasn)
 		return -ENOBUFS;
 
+	iwl_mvm_ftm_remove_pasn_sta(mvm, addr);
+
 	pasn->cipher = iwl_mvm_cipher_to_location_cipher(cipher);
 
 	switch (pasn->cipher) {
@@ -499,7 +501,7 @@
 		rcu_read_lock();
 
 		sta = rcu_dereference(mvm->fw_id_to_mac_id[mvmvif->ap_sta_id]);
-		if (sta->mfp)
+		if (sta->mfp && (peer->ftm.trigger_based || peer->ftm.non_trigger_based))
 			FTM_PUT_FLAG(PMF);
 
 		rcu_read_unlock();
@@ -1054,7 +1056,7 @@
 	overshoot = IWL_MVM_FTM_INITIATOR_SMOOTH_OVERSHOOT;
 	alpha = IWL_MVM_FTM_INITIATOR_SMOOTH_ALPHA;
 
-	rtt_avg = (alpha * rtt + (100 - alpha) * resp->rtt_avg) / 100;
+	rtt_avg = div_s64(alpha * rtt + (100 - alpha) * resp->rtt_avg, 100);
 
 	IWL_DEBUG_INFO(mvm,
 		       "%pM: prev rtt_avg=%lld, new rtt_avg=%lld, rtt=%lld\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/fw.c
@@ -95,20 +95,10 @@
 {
 	struct iwl_rx_packet *pkt = rxb_addr(rxb);
 	struct iwl_mfu_assert_dump_notif *mfu_dump_notif = (void *)pkt->data;
-	__le32 *dump_data = mfu_dump_notif->data;
-	int n_words = le32_to_cpu(mfu_dump_notif->data_size) / sizeof(__le32);
-	int i;
 
 	if (mfu_dump_notif->index_num == 0)
 		IWL_INFO(mvm, "MFUART assert id 0x%x occurred\n",
 			 le32_to_cpu(mfu_dump_notif->assert_id));
-
-	for (i = 0; i < n_words; i++)
-		IWL_DEBUG_INFO(mvm,
-			       "MFUART assert dump, dword %u: 0x%08x\n",
-			       le16_to_cpu(mfu_dump_notif->index_num) *
-			       n_words + i,
-			       le32_to_cpu(dump_data[i]));
 }
 
 static bool iwl_alive_fn(struct iwl_notif_wait_data *notif_wait,
@@ -686,7 +676,7 @@
 		mvm->nvm_data->bands[0].n_channels = 1;
 		mvm->nvm_data->bands[0].n_bitrates = 1;
 		mvm->nvm_data->bands[0].bitrates =
-			(void *)mvm->nvm_data->channels + 1;
+			(void *)(mvm->nvm_data->channels + 1);
 		mvm->nvm_data->bands[0].bitrates->hw_value = 10;
 	}
 
@@ -972,6 +962,11 @@
 	int i, j, ret, num_sub_bands, cmd_size;
 	s8 *gain;
 
+	/* many firmware images for JF lie about this */
+	if (CSR_HW_RFID_TYPE(mvm->trans->hw_rf_id) ==
+	    CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_JF))
+		return 0;
+
 	if (!fw_has_capa(&mvm->fw->ucode_capa, IWL_UCODE_TLV_CAPA_SET_PPAG)) {
 		IWL_DEBUG_RADIO(mvm,
 				"PPAG capability not supported by FW, command not sent.\n");
@@ -1029,7 +1024,7 @@
 		IWL_ERR(mvm, "failed to send PER_PLATFORM_ANT_GAIN_CMD (%d)\n",
 			ret);
 
-	return ret;
+	return 0;
 }
 
 static const struct dmi_system_id dmi_ppag_approved_list[] = {
@@ -1282,11 +1277,18 @@
 }
 #endif /* CONFIG_ACPI */
 
+static void iwl_mvm_disconnect_iterator(void *data, u8 *mac,
+					struct ieee80211_vif *vif)
+{
+	if (vif->type == NL80211_IFTYPE_STATION)
+		ieee80211_hw_restart_disconnect(vif);
+}
+
 void iwl_mvm_send_recovery_cmd(struct iwl_mvm *mvm, u32 flags)
 {
 	u32 error_log_size = mvm->fw->ucode_capa.error_log_size;
+	u32 status = 0;
 	int ret;
-	u32 resp;
 
 	struct iwl_fw_error_recovery_cmd recovery_cmd = {
 		.flags = cpu_to_le32(flags),
@@ -1294,7 +1296,6 @@
 	};
 	struct iwl_host_cmd host_cmd = {
 		.id = WIDE_ID(SYSTEM_GROUP, FW_ERROR_RECOVERY_CMD),
-		.flags = CMD_WANT_SKB,
 		.data = {&recovery_cmd, },
 		.len = {sizeof(recovery_cmd), },
 	};
@@ -1314,7 +1315,7 @@
 		recovery_cmd.buf_size = cpu_to_le32(error_log_size);
 	}
 
-	ret = iwl_mvm_send_cmd(mvm, &host_cmd);
+	ret = iwl_mvm_send_cmd_status(mvm, &host_cmd, &status);
 	kfree(mvm->error_recovery_buf);
 	mvm->error_recovery_buf = NULL;
 
@@ -1325,11 +1326,15 @@
 
 	/* skb respond is only relevant in ERROR_RECOVERY_UPDATE_DB */
 	if (flags & ERROR_RECOVERY_UPDATE_DB) {
-		resp = le32_to_cpu(*(__le32 *)host_cmd.resp_pkt->data);
-		if (resp)
+		if (status) {
 			IWL_ERR(mvm,
 				"Failed to send recovery cmd blob was invalid %d\n",
-				resp);
+				status);
+
+			ieee80211_iterate_interfaces(mvm->hw, 0,
+						     iwl_mvm_disconnect_iterator,
+						     mvm);
+		}
 	}
 }
 
@@ -1489,8 +1494,10 @@
 	while (!sband && i < NUM_NL80211_BANDS)
 		sband = mvm->hw->wiphy->bands[i++];
 
-	if (WARN_ON_ONCE(!sband))
+	if (WARN_ON_ONCE(!sband)) {
+		ret = -ENODEV;
 		goto error;
+	}
 
 	chan = &sband->channels[0];
 
@@ -1572,7 +1579,7 @@
 	ret = iwl_mvm_sar_init(mvm);
 	if (ret == 0)
 		ret = iwl_mvm_sar_geo_init(mvm);
-	else if (ret < 0)
+	if (ret < 0)
 		goto error;
 
 	iwl_mvm_tas_init(mvm);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
@@ -16,6 +16,7 @@
 #include <net/ieee80211_radiotap.h>
 #include <net/tcp.h>
 
+#include "iwl-drv.h"
 #include "iwl-op-mode.h"
 #include "iwl-io.h"
 #include "mvm.h"
@@ -294,7 +295,6 @@
 	 [0] = WLAN_EXT_CAPA1_EXT_CHANNEL_SWITCHING,
 	 [2] = WLAN_EXT_CAPA3_MULTI_BSSID_SUPPORT,
 	 [7] = WLAN_EXT_CAPA8_OPMODE_NOTIF,
-	 [9] = WLAN_EXT_CAPA10_TWT_REQUESTER_SUPPORT,
 };
 
 static const struct wiphy_iftype_ext_capab he_iftypes_ext_capa[] = {
@@ -820,7 +820,10 @@
 
 	rcu_read_lock();
 	do {
-		while (likely(!mvmtxq->stopped &&
+		while (likely(!test_bit(IWL_MVM_TXQ_STATE_STOP_FULL,
+					&mvmtxq->state) &&
+			      !test_bit(IWL_MVM_TXQ_STATE_STOP_REDIRECT,
+					&mvmtxq->state) &&
 			      !test_bit(IWL_MVM_STATUS_IN_D3, &mvm->status))) {
 			skb = ieee80211_tx_dequeue(hw, txq);
 
@@ -1116,9 +1119,30 @@
 {
 	struct iwl_mvm *mvm = IWL_MAC80211_GET_MVM(hw);
 	int ret;
+	int retry, max_retry = 0;
 
 	mutex_lock(&mvm->mutex);
-	ret = __iwl_mvm_mac_start(mvm);
+
+	/* we are starting the mac not in error flow, and restart is enabled */
+	if (!test_bit(IWL_MVM_STATUS_HW_RESTART_REQUESTED, &mvm->status) &&
+	    iwlwifi_mod_params.fw_restart) {
+		max_retry = IWL_MAX_INIT_RETRY;
+		/*
+		 * This will prevent mac80211 recovery flows to trigger during
+		 * init failures
+		 */
+		set_bit(IWL_MVM_STATUS_STARTING, &mvm->status);
+	}
+
+	for (retry = 0; retry <= max_retry; retry++) {
+		ret = __iwl_mvm_mac_start(mvm);
+		if (!ret)
+			break;
+
+		IWL_ERR(mvm, "mac start retry %d\n", retry);
+	}
+	clear_bit(IWL_MVM_STATUS_STARTING, &mvm->status);
+
 	mutex_unlock(&mvm->mutex);
 
 	return ret;
@@ -1665,6 +1689,7 @@
 	struct iwl_mvm_mc_iter_data iter_data = {
 		.mvm = mvm,
 	};
+	int ret;
 
 	lockdep_assert_held(&mvm->mutex);
 
@@ -1674,6 +1699,22 @@
 	ieee80211_iterate_active_interfaces_atomic(
 		mvm->hw, IEEE80211_IFACE_ITER_NORMAL,
 		iwl_mvm_mc_iface_iterator, &iter_data);
+
+	/*
+	 * Send a (synchronous) ech command so that we wait for the
+	 * multiple asynchronous MCAST_FILTER_CMD commands sent by
+	 * the interface iterator. Otherwise, we might get here over
+	 * and over again (by userspace just sending a lot of these)
+	 * and the CPU can send them faster than the firmware can
+	 * process them.
+	 * Note that the CPU is still faster - but with this we'll
+	 * actually send fewer commands overall because the CPU will
+	 * not schedule the work in mac80211 as frequently if it's
+	 * still running when rescheduled (possibly multiple times).
+	 */
+	ret = iwl_mvm_send_cmd_pdu(mvm, ECHO_CMD, 0, 0, NULL);
+	if (ret)
+		IWL_ERR(mvm, "Failed to synchronize multicast groups update\n");
 }
 
 static u64 iwl_mvm_prepare_multicast(struct ieee80211_hw *hw,
@@ -4735,6 +4776,10 @@
 	int i;
 
 	if (!iwl_mvm_has_new_tx_api(mvm)) {
+		/* we can't ask the firmware anything if it is dead */
+		if (test_bit(IWL_MVM_STATUS_HW_RESTART_REQUESTED,
+			     &mvm->status))
+			return;
 		if (drop) {
 			mutex_lock(&mvm->mutex);
 			iwl_mvm_flush_tx_path(mvm,
@@ -4816,8 +4861,11 @@
 
 	/* this can take a while, and we may need/want other operations
 	 * to succeed while doing this, so do it without the mutex held
+	 * If the firmware is dead, this can't work...
 	 */
-	if (!drop && !iwl_mvm_has_new_tx_api(mvm))
+	if (!drop && !iwl_mvm_has_new_tx_api(mvm) &&
+	    !test_bit(IWL_MVM_STATUS_HW_RESTART_REQUESTED,
+		      &mvm->status))
 		iwl_trans_wait_tx_queues_empty(mvm->trans, msk);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/mvm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/mvm.h
@@ -727,7 +727,9 @@
 	struct list_head list;
 	u16 txq_id;
 	atomic_t tx_request;
-	bool stopped;
+#define IWL_MVM_TXQ_STATE_STOP_FULL	0
+#define IWL_MVM_TXQ_STATE_STOP_REDIRECT	1
+	unsigned long state;
 };
 
 static inline struct iwl_mvm_txq *
@@ -1121,6 +1123,8 @@
  * @IWL_MVM_STATUS_FIRMWARE_RUNNING: firmware is running
  * @IWL_MVM_STATUS_NEED_FLUSH_P2P: need to flush P2P bcast STA
  * @IWL_MVM_STATUS_IN_D3: in D3 (or at least about to go into it)
+ * @IWL_MVM_STATUS_STARTING: starting mac,
+ *	used to disable restart flow while in STARTING state
  */
 enum iwl_mvm_status {
 	IWL_MVM_STATUS_HW_RFKILL,
@@ -1132,6 +1136,7 @@
 	IWL_MVM_STATUS_FIRMWARE_RUNNING,
 	IWL_MVM_STATUS_NEED_FLUSH_P2P,
 	IWL_MVM_STATUS_IN_D3,
+	IWL_MVM_STATUS_STARTING,
 };
 
 /* Keep track of completed init configuration */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/nvm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/nvm.c
@@ -445,6 +445,11 @@
 		struct iwl_mcc_update_resp *mcc_resp = (void *)pkt->data;
 
 		n_channels =  __le32_to_cpu(mcc_resp->n_channels);
+		if (iwl_rx_packet_payload_len(pkt) !=
+		    struct_size(mcc_resp, channels, n_channels)) {
+			resp_cp = ERR_PTR(-EINVAL);
+			goto exit;
+		}
 		resp_len = sizeof(struct iwl_mcc_update_resp) +
 			   n_channels * sizeof(__le32);
 		resp_cp = kmemdup(mcc_resp, resp_len, GFP_KERNEL);
@@ -456,6 +461,11 @@
 		struct iwl_mcc_update_resp_v3 *mcc_resp_v3 = (void *)pkt->data;
 
 		n_channels =  __le32_to_cpu(mcc_resp_v3->n_channels);
+		if (iwl_rx_packet_payload_len(pkt) !=
+		    struct_size(mcc_resp_v3, channels, n_channels)) {
+			resp_cp = ERR_PTR(-EINVAL);
+			goto exit;
+		}
 		resp_len = sizeof(struct iwl_mcc_update_resp) +
 			   n_channels * sizeof(__le32);
 		resp_cp = kzalloc(resp_len, GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/ops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/ops.c
@@ -238,7 +238,8 @@
 	 */
 	mvm->fw_static_smps_request =
 		req->event == cpu_to_le32(THERMAL_DUAL_CHAIN_REQ_DISABLE);
-	ieee80211_iterate_interfaces(mvm->hw, IEEE80211_IFACE_ITER_NORMAL,
+	ieee80211_iterate_interfaces(mvm->hw,
+				     IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER,
 				     iwl_mvm_intf_dual_chain_req, NULL);
 }
 
@@ -652,11 +653,6 @@
 	mutex_unlock(&mvm->mutex);
 }
 
-static bool iwl_mvm_fwrt_fw_running(void *ctx)
-{
-	return iwl_mvm_firmware_running(ctx);
-}
-
 static int iwl_mvm_fwrt_send_hcmd(void *ctx, struct iwl_host_cmd *host_cmd)
 {
 	struct iwl_mvm *mvm = (struct iwl_mvm *)ctx;
@@ -677,7 +673,6 @@
 static const struct iwl_fw_runtime_ops iwl_mvm_fwrt_ops = {
 	.dump_start = iwl_mvm_fwrt_dump_start,
 	.dump_end = iwl_mvm_fwrt_dump_end,
-	.fw_running = iwl_mvm_fwrt_fw_running,
 	.send_hcmd = iwl_mvm_fwrt_send_hcmd,
 	.d3_debug_enable = iwl_mvm_d3_debug_enable,
 };
@@ -687,6 +682,7 @@
 	int ret;
 
 	rtnl_lock();
+	wiphy_lock(mvm->hw->wiphy);
 	mutex_lock(&mvm->mutex);
 
 	ret = iwl_run_init_mvm_ucode(mvm);
@@ -702,6 +698,7 @@
 		iwl_mvm_stop_device(mvm);
 
 	mutex_unlock(&mvm->mutex);
+	wiphy_unlock(mvm->hw->wiphy);
 	rtnl_unlock();
 
 	if (ret < 0)
@@ -758,12 +755,12 @@
 	if (!hw)
 		return NULL;
 
-	hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
+	hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
 
 	if (cfg->max_tx_agg_size)
 		hw->max_tx_aggregation_subframes = cfg->max_tx_agg_size;
 	else
-		hw->max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
+		hw->max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
 
 	op_mode = hw->priv;
 
@@ -1021,6 +1018,8 @@
 
 	clear_bit(IWL_MVM_STATUS_FIRMWARE_RUNNING, &mvm->status);
 
+	iwl_mvm_pause_tcm(mvm, false);
+
 	iwl_fw_dbg_stop_sync(&mvm->fwrt);
 	iwl_trans_stop_device(mvm->trans);
 	iwl_free_fw_paging(&mvm->fwrt);
@@ -1301,10 +1300,16 @@
 
 		txq = sta->txq[tid];
 		mvmtxq = iwl_mvm_txq_from_mac80211(txq);
-		mvmtxq->stopped = !start;
+		if (start)
+			clear_bit(IWL_MVM_TXQ_STATE_STOP_FULL, &mvmtxq->state);
+		else
+			set_bit(IWL_MVM_TXQ_STATE_STOP_FULL, &mvmtxq->state);
 
-		if (start && mvmsta->sta_state != IEEE80211_STA_NOTEXIST)
+		if (start && mvmsta->sta_state != IEEE80211_STA_NOTEXIST) {
+			local_bh_disable();
 			iwl_mvm_mac_itxq_xmit(mvm->hw, txq);
+			local_bh_enable();
+		}
 	}
 
 out:
@@ -1424,6 +1429,9 @@
 	 */
 	if (!mvm->fw_restart && fw_error) {
 		iwl_fw_error_collect(&mvm->fwrt, false);
+	} else if (test_bit(IWL_MVM_STATUS_STARTING,
+			    &mvm->status)) {
+		IWL_ERR(mvm, "Starting mac, retry will be triggered anyway\n");
 	} else if (test_bit(IWL_MVM_STATUS_IN_HW_RESTART, &mvm->status)) {
 		struct iwl_mvm_reprobe *reprobe;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/phy-ctxt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/phy-ctxt.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
 /*
- * Copyright (C) 2012-2014, 2018-2021 Intel Corporation
+ * Copyright (C) 2012-2014, 2018-2022 Intel Corporation
  * Copyright (C) 2013-2014 Intel Mobile Communications GmbH
  * Copyright (C) 2017 Intel Deutschland GmbH
  */
@@ -99,17 +99,6 @@
 		active_cnt = 2;
 	}
 
-	/*
-	 * If the firmware requested it, then we know that it supports
-	 * getting zero for the values to indicate "use one, but pick
-	 * which one yourself", which means it can dynamically pick one
-	 * that e.g. has better RSSI.
-	 */
-	if (mvm->fw_static_smps_request && active_cnt == 1 && idle_cnt == 1) {
-		idle_cnt = 0;
-		active_cnt = 0;
-	}
-
 	*rxchain_info = cpu_to_le32(iwl_mvm_get_valid_rx_ant(mvm) <<
 					PHY_RX_CHAIN_VALID_POS);
 	*rxchain_info |= cpu_to_le32(idle_cnt << PHY_RX_CHAIN_CNT_POS);
@@ -295,19 +284,32 @@
 	 * otherwise we might not be able to reuse this phy.
 	 */
 	if (ctxt->ref == 0) {
-		struct ieee80211_channel *chan;
+		struct ieee80211_channel *chan = NULL;
 		struct cfg80211_chan_def chandef;
-		struct ieee80211_supported_band *sband = NULL;
-		enum nl80211_band band = NL80211_BAND_2GHZ;
-
-		while (!sband && band < NUM_NL80211_BANDS)
-			sband = mvm->hw->wiphy->bands[band++];
+		struct ieee80211_supported_band *sband;
+		enum nl80211_band band;
+		int channel;
+
+		for (band = NL80211_BAND_2GHZ; band < NUM_NL80211_BANDS; band++) {
+			sband = mvm->hw->wiphy->bands[band];
+
+			if (!sband)
+				continue;
+
+			for (channel = 0; channel < sband->n_channels; channel++)
+				if (!(sband->channels[channel].flags &
+						IEEE80211_CHAN_DISABLED)) {
+					chan = &sband->channels[channel];
+					break;
+				}
+
+			if (chan)
+				break;
+		}
 
-		if (WARN_ON(!sband))
+		if (WARN_ON(!chan))
 			return;
 
-		chan = &sband->channels[0];
-
 		cfg80211_chandef_create(&chandef, chan, NL80211_CHAN_NO_HT);
 		iwl_mvm_phy_ctxt_changed(mvm, ctxt, &chandef, 1, 1);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/power.c
@@ -563,6 +563,9 @@
 	struct iwl_power_vifs *power_iterator = _data;
 	bool active = mvmvif->phy_ctxt && mvmvif->phy_ctxt->id < NUM_PHY_CTX;
 
+	if (!mvmvif->uploaded)
+		return;
+
 	switch (ieee80211_vif_type_p2p(vif)) {
 	case NL80211_IFTYPE_P2P_DEVICE:
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/rfi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/rfi.c
@@ -104,15 +104,17 @@
 	if (ret)
 		return ERR_PTR(ret);
 
-	if (WARN_ON_ONCE(iwl_rx_packet_payload_len(cmd.resp_pkt) != resp_size))
+	if (WARN_ON_ONCE(iwl_rx_packet_payload_len(cmd.resp_pkt) !=
+			 resp_size)) {
+		iwl_free_resp(&cmd);
 		return ERR_PTR(-EIO);
+	}
+
+	resp = kmemdup(cmd.resp_pkt->data, resp_size, GFP_KERNEL);
+	iwl_free_resp(&cmd);
 
-	resp = kzalloc(resp_size, GFP_KERNEL);
 	if (!resp)
 		return ERR_PTR(-ENOMEM);
 
-	memcpy(resp, cmd.resp_pkt->data, resp_size);
-
-	iwl_free_resp(&cmd);
 	return resp;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
@@ -1119,10 +1119,13 @@
 
 		rate->bw = RATE_MCS_CHAN_WIDTH_20;
 
-		WARN_ON_ONCE(rate->index < IWL_RATE_MCS_0_INDEX ||
-			     rate->index > IWL_RATE_MCS_9_INDEX);
+		if (WARN_ON_ONCE(rate->index < IWL_RATE_MCS_0_INDEX))
+			rate->index = rs_ht_to_legacy[IWL_RATE_MCS_0_INDEX];
+		else if (WARN_ON_ONCE(rate->index > IWL_RATE_MCS_9_INDEX))
+			rate->index = rs_ht_to_legacy[IWL_RATE_MCS_9_INDEX];
+		else
+			rate->index = rs_ht_to_legacy[rate->index];
 
-		rate->index = rs_ht_to_legacy[rate->index];
 		rate->ldpc = false;
 	} else {
 		/* Downgrade to SISO with same MCS if in MIMO  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/rs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/rs.h
@@ -133,13 +133,8 @@
 
 #define LINK_QUAL_AGG_FRAME_LIMIT_DEF	(63)
 #define LINK_QUAL_AGG_FRAME_LIMIT_MAX	(63)
-/*
- * FIXME - various places in firmware API still use u8,
- * e.g. LQ command and SCD config command.
- * This should be 256 instead.
- */
-#define LINK_QUAL_AGG_FRAME_LIMIT_GEN2_DEF	(255)
-#define LINK_QUAL_AGG_FRAME_LIMIT_GEN2_MAX	(255)
+#define LINK_QUAL_AGG_FRAME_LIMIT_GEN2_DEF	(64)
+#define LINK_QUAL_AGG_FRAME_LIMIT_GEN2_MAX	(64)
 #define LINK_QUAL_AGG_FRAME_LIMIT_MIN	(0)
 
 #define LQ_SIZE		2	/* 2 mode tables:  "Active" and "Search" */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/rx.c
@@ -83,8 +83,8 @@
 	fraglen = len - hdrlen;
 
 	if (fraglen) {
-		int offset = (void *)hdr + hdrlen -
-			     rxb_addr(rxb) + rxb_offset(rxb);
+		int offset = (u8 *)hdr + hdrlen -
+			     (u8 *)rxb_addr(rxb) + rxb_offset(rxb);
 
 		skb_add_rx_frag(skb, 0, rxb_steal_page(rxb), offset,
 				fraglen, rxb->truesize);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c
@@ -121,12 +121,39 @@
 	struct iwl_rx_mpdu_desc *desc = (void *)pkt->data;
 	unsigned int headlen, fraglen, pad_len = 0;
 	unsigned int hdrlen = ieee80211_hdrlen(hdr->frame_control);
+	u8 mic_crc_len = u8_get_bits(desc->mac_flags1,
+				     IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK) << 1;
 
 	if (desc->mac_flags2 & IWL_RX_MPDU_MFLG2_PAD) {
 		len -= 2;
 		pad_len = 2;
 	}
 
+	/*
+	 * For non monitor interface strip the bytes the RADA might not have
+	 * removed. As monitor interface cannot exist with other interfaces
+	 * this removal is safe.
+	 */
+	if (mic_crc_len && !ieee80211_hw_check(mvm->hw, RX_INCLUDES_FCS)) {
+		u32 pkt_flags = le32_to_cpu(pkt->len_n_flags);
+
+		/*
+		 * If RADA was not enabled then decryption was not performed so
+		 * the MIC cannot be removed.
+		 */
+		if (!(pkt_flags & FH_RSCSR_RADA_EN)) {
+			if (WARN_ON(crypt_len > mic_crc_len))
+				return -EINVAL;
+
+			mic_crc_len -= crypt_len;
+		}
+
+		if (WARN_ON(mic_crc_len > len))
+			return -EINVAL;
+
+		len -= mic_crc_len;
+	}
+
 	/* If frame is small enough to fit in skb->head, pull it completely.
 	 * If not, only pull ieee80211_hdr (including crypto if present, and
 	 * an additional 8 bytes for SNAP/ethertype, see below) so that
@@ -193,8 +220,8 @@
 	fraglen = len - headlen;
 
 	if (fraglen) {
-		int offset = (void *)hdr + headlen + pad_len -
-			     rxb_addr(rxb) + rxb_offset(rxb);
+		int offset = (u8 *)hdr + headlen + pad_len -
+			     (u8 *)rxb_addr(rxb) + rxb_offset(rxb);
 
 		skb_add_rx_frag(skb, 0, rxb_steal_page(rxb), offset,
 				fraglen, rxb->truesize);
@@ -275,8 +302,10 @@
 static int iwl_mvm_rx_mgmt_prot(struct ieee80211_sta *sta,
 				struct ieee80211_hdr *hdr,
 				struct iwl_rx_mpdu_desc *desc,
-				u32 status)
+				u32 status,
+				struct ieee80211_rx_status *stats)
 {
+	struct wireless_dev *wdev;
 	struct iwl_mvm_sta *mvmsta;
 	struct iwl_mvm_vif *mvmvif;
 	u8 keyid;
@@ -298,21 +327,22 @@
 	if (!ieee80211_is_beacon(hdr->frame_control))
 		return 0;
 
+	if (!sta)
+		return -1;
+
+	mvmsta = iwl_mvm_sta_from_mac80211(sta);
+	mvmvif = iwl_mvm_vif_from_mac80211(mvmsta->vif);
+
 	/* key mismatch - will also report !MIC_OK but we shouldn't count it */
 	if (!(status & IWL_RX_MPDU_STATUS_KEY_VALID))
-		return -1;
+		goto report;
 
 	/* good cases */
 	if (likely(status & IWL_RX_MPDU_STATUS_MIC_OK &&
-		   !(status & IWL_RX_MPDU_STATUS_REPLAY_ERROR)))
+		   !(status & IWL_RX_MPDU_STATUS_REPLAY_ERROR))) {
+		stats->flag |= RX_FLAG_DECRYPTED;
 		return 0;
-
-	if (!sta)
-		return -1;
-
-	mvmsta = iwl_mvm_sta_from_mac80211(sta);
-
-	mvmvif = iwl_mvm_vif_from_mac80211(mvmsta->vif);
+	}
 
 	/*
 	 * both keys will have the same cipher and MIC length, use
@@ -322,11 +352,11 @@
 	if (!key) {
 		key = rcu_dereference(mvmvif->bcn_prot.keys[1]);
 		if (!key)
-			return -1;
+			goto report;
 	}
 
 	if (len < key->icv_len + IEEE80211_GMAC_PN_LEN + 2)
-		return -1;
+		goto report;
 
 	/* get the real key ID */
 	keyid = frame[len - key->icv_len - IEEE80211_GMAC_PN_LEN - 2];
@@ -340,7 +370,7 @@
 			return -1;
 		key = rcu_dereference(mvmvif->bcn_prot.keys[keyid - 6]);
 		if (!key)
-			return -1;
+			goto report;
 	}
 
 	/* Report status to mac80211 */
@@ -348,6 +378,10 @@
 		ieee80211_key_mic_failure(key);
 	else if (status & IWL_RX_MPDU_STATUS_REPLAY_ERROR)
 		ieee80211_key_replay(key);
+report:
+	wdev = ieee80211_vif_to_wdev(mvmsta->vif);
+	if (wdev->netdev)
+		cfg80211_rx_unprot_mlme_mgmt(wdev->netdev, (void *)hdr, len);
 
 	return -1;
 }
@@ -374,7 +408,7 @@
 
 	if (unlikely(ieee80211_is_mgmt(hdr->frame_control) &&
 		     !ieee80211_has_protected(hdr->frame_control)))
-		return iwl_mvm_rx_mgmt_prot(sta, hdr, desc, status);
+		return iwl_mvm_rx_mgmt_prot(sta, hdr, desc, status, stats);
 
 	if (!ieee80211_has_protected(hdr->frame_control) ||
 	    (status & IWL_RX_MPDU_STATUS_SEC_MASK) ==
@@ -1880,7 +1914,7 @@
 				RCU_INIT_POINTER(mvm->csa_tx_blocked_vif, NULL);
 				/* Unblock BCAST / MCAST station */
 				iwl_mvm_modify_all_sta_disable_tx(mvm, mvmvif, false);
-				cancel_delayed_work_sync(&mvm->cs_tx_unblock_dwork);
+				cancel_delayed_work(&mvm->cs_tx_unblock_dwork);
 			}
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/scan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/scan.c
@@ -834,8 +834,8 @@
 	return ((n_ssids <= PROBE_OPTION_MAX) &&
 		(n_channels <= mvm->fw->ucode_capa.n_scan_channels) &
 		(ies->common_ie_len +
-		 ies->len[NL80211_BAND_2GHZ] +
-		 ies->len[NL80211_BAND_5GHZ] <=
+		 ies->len[NL80211_BAND_2GHZ] + ies->len[NL80211_BAND_5GHZ] +
+		 ies->len[NL80211_BAND_6GHZ] <=
 		 iwl_mvm_max_scan_ie_fw_cmd_room(mvm)));
 }
 
@@ -1312,7 +1312,7 @@
 		if (IWL_MVM_ADWELL_MAX_BUDGET)
 			cmd->v7.adwell_max_budget =
 				cpu_to_le16(IWL_MVM_ADWELL_MAX_BUDGET);
-		else if (params->ssids && params->ssids[0].ssid_len)
+		else if (params->n_ssids && params->ssids[0].ssid_len)
 			cmd->v7.adwell_max_budget =
 				cpu_to_le16(IWL_SCAN_ADWELL_MAX_BUDGET_DIRECTED_SCAN);
 		else
@@ -1414,7 +1414,7 @@
 	if (IWL_MVM_ADWELL_MAX_BUDGET)
 		general_params->adwell_max_budget =
 			cpu_to_le16(IWL_MVM_ADWELL_MAX_BUDGET);
-	else if (params->ssids && params->ssids[0].ssid_len)
+	else if (params->n_ssids && params->ssids[0].ssid_len)
 		general_params->adwell_max_budget =
 			cpu_to_le16(IWL_SCAN_ADWELL_MAX_BUDGET_DIRECTED_SCAN);
 	else
@@ -1721,7 +1721,10 @@
 				break;
 		}
 
-		if (k == idex_b && idex_b < SCAN_BSSID_MAX_SIZE) {
+		if (k == idex_b && idex_b < SCAN_BSSID_MAX_SIZE &&
+		    !WARN_ONCE(!is_valid_ether_addr(scan_6ghz_params[j].bssid),
+			       "scan: invalid BSSID at index %u, index_b=%u\n",
+			       j, idex_b)) {
 			memcpy(&pp->bssid_array[idex_b++],
 			       scan_6ghz_params[j].bssid, ETH_ALEN);
 		}
@@ -1750,7 +1753,8 @@
 			&cp->channel_config[i];
 
 		u32 s_ssid_bitmap = 0, bssid_bitmap = 0, flags = 0;
-		u8 j, k, s_max = 0, b_max = 0, n_used_bssid_entries;
+		u8 k, s_max = 0, b_max = 0, n_used_bssid_entries;
+		u32 j;
 		bool force_passive, found = false, allow_passive = true,
 		     unsolicited_probe_on_chan = false, psc_no_listen = false;
 
@@ -1890,7 +1894,10 @@
 			IWL_SCAN_CHANNEL_FLAG_CACHE_ADD;
 
 	/* set fragmented ebs for fragmented scan on HB channels */
-	if (iwl_mvm_is_scan_fragmented(params->hb_type))
+	if ((!iwl_mvm_is_cdb_supported(mvm) &&
+	     iwl_mvm_is_scan_fragmented(params->type)) ||
+	    (iwl_mvm_is_cdb_supported(mvm) &&
+	     iwl_mvm_is_scan_fragmented(params->hb_type)))
 		flags |= IWL_SCAN_CHANNEL_FLAG_EBS_FRAG;
 
 	return flags;
@@ -1924,22 +1931,19 @@
 	}
 
 	/*
-	 * 6GHz passive scan is allowed while associated in a defined time
-	 * interval following HW reset or resume flow
+	 * 6GHz passive scan is allowed in a defined time interval following HW
+	 * reset or resume flow, or while not associated and a large interval
+	 * has passed since the last 6GHz passive scan.
 	 */
-	if (vif->bss_conf.assoc &&
+	if ((vif->bss_conf.assoc ||
+	     time_after(mvm->last_6ghz_passive_scan_jiffies +
+			(IWL_MVM_6GHZ_PASSIVE_SCAN_TIMEOUT * HZ), jiffies)) &&
 	    (time_before(mvm->last_reset_or_resume_time_jiffies +
 			 (IWL_MVM_6GHZ_PASSIVE_SCAN_ASSOC_TIMEOUT * HZ),
 			 jiffies))) {
-		IWL_DEBUG_SCAN(mvm, "6GHz passive scan: associated\n");
-		return;
-	}
-
-	/* No need for 6GHz passive scan if not enough time elapsed */
-	if (time_after(mvm->last_6ghz_passive_scan_jiffies +
-		       (IWL_MVM_6GHZ_PASSIVE_SCAN_TIMEOUT * HZ), jiffies)) {
-		IWL_DEBUG_SCAN(mvm,
-			       "6GHz passive scan: timeout did not expire\n");
+		IWL_DEBUG_SCAN(mvm, "6GHz passive scan: %s\n",
+			       vif->bss_conf.assoc ? "associated" :
+			       "timeout did not expire");
 		return;
 	}
 
@@ -2150,7 +2154,7 @@
 	struct iwl_scan_req_umac *cmd = mvm->scan_cmd;
 	struct iwl_scan_umac_chan_param *chan_param;
 	void *cmd_data = iwl_mvm_get_scan_req_umac_data(mvm);
-	void *sec_part = cmd_data + sizeof(struct iwl_scan_channel_cfg_umac) *
+	void *sec_part = (u8 *)cmd_data + sizeof(struct iwl_scan_channel_cfg_umac) *
 		mvm->fw->ucode_capa.n_scan_channels;
 	struct iwl_scan_req_umac_tail_v2 *tail_v2 =
 		(struct iwl_scan_req_umac_tail_v2 *)sec_part;
@@ -2490,7 +2494,7 @@
 	return -EIO;
 }
 
-#define SCAN_TIMEOUT 20000
+#define SCAN_TIMEOUT 30000
 
 void iwl_mvm_scan_timeout_wk(struct work_struct *work)
 {
@@ -2571,7 +2575,8 @@
 		if (ver_handler->version != scan_ver)
 			continue;
 
-		return ver_handler->handler(mvm, vif, params, type, uid);
+		err = ver_handler->handler(mvm, vif, params, type, uid);
+		return err ? : uid;
 	}
 
 	err = iwl_mvm_scan_umac(mvm, vif, params, type, uid);
@@ -2771,18 +2776,16 @@
 		params.n_channels = j;
 	}
 
-	if (non_psc_included &&
-	    !iwl_mvm_scan_fits(mvm, req->n_ssids, ies, params.n_channels)) {
-		kfree(params.channels);
-		return -ENOBUFS;
+	if (!iwl_mvm_scan_fits(mvm, req->n_ssids, ies, params.n_channels)) {
+		ret = -ENOBUFS;
+		goto out;
 	}
 
 	uid = iwl_mvm_build_scan_cmd(mvm, vif, &hcmd, &params, type);
-
-	if (non_psc_included)
-		kfree(params.channels);
-	if (uid < 0)
-		return uid;
+	if (uid < 0) {
+		ret = uid;
+		goto out;
+	}
 
 	ret = iwl_mvm_send_cmd(mvm, &hcmd);
 	if (!ret) {
@@ -2799,6 +2802,9 @@
 		mvm->sched_scan_pass_all = SCHED_SCAN_PASS_ALL_DISABLED;
 	}
 
+out:
+	if (non_psc_included)
+		kfree(params.channels);
 	return ret;
 }
 
@@ -3064,7 +3070,7 @@
 	if (!(mvm->scan_status & type))
 		return 0;
 
-	if (iwl_mvm_is_radio_killed(mvm)) {
+	if (!test_bit(STATUS_DEVICE_ENABLED, &mvm->trans->status)) {
 		ret = 0;
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/sta.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/sta.c
@@ -640,7 +640,7 @@
 			    queue, iwl_mvm_ac_to_tx_fifo[ac]);
 
 	/* Stop the queue and wait for it to empty */
-	txq->stopped = true;
+	set_bit(IWL_MVM_TXQ_STATE_STOP_REDIRECT, &txq->state);
 
 	ret = iwl_trans_wait_tx_queues_empty(mvm->trans, BIT(queue));
 	if (ret) {
@@ -683,7 +683,7 @@
 
 out:
 	/* Continue using the queue */
-	txq->stopped = false;
+	clear_bit(IWL_MVM_TXQ_STATE_STOP_REDIRECT, &txq->state);
 
 	return ret;
 }
@@ -1794,6 +1794,7 @@
 			iwl_mvm_txq_from_mac80211(sta->txq[i]);
 
 		mvmtxq->txq_id = IWL_MVM_INVALID_QUEUE;
+		list_del_init(&mvmtxq->list);
 	}
 }
 
@@ -2543,7 +2544,7 @@
 	}
 
 	if (iwl_mvm_has_new_rx_api(mvm) && start) {
-		u16 reorder_buf_size = buf_size * sizeof(baid_data->entries[0]);
+		u32 reorder_buf_size = buf_size * sizeof(baid_data->entries[0]);
 
 		/* sparse doesn't like the __align() so don't check */
 #ifndef __CHECKER__
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/time-event.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/time-event.c
@@ -49,14 +49,13 @@
 	struct iwl_mvm *mvm = container_of(wk, struct iwl_mvm, roc_done_wk);
 
 	/*
-	 * Clear the ROC_RUNNING /ROC_AUX_RUNNING status bit.
+	 * Clear the ROC_RUNNING status bit.
 	 * This will cause the TX path to drop offchannel transmissions.
 	 * That would also be done by mac80211, but it is racy, in particular
 	 * in the case that the time event actually completed in the firmware
 	 * (which is handled in iwl_mvm_te_handle_notif).
 	 */
 	clear_bit(IWL_MVM_STATUS_ROC_RUNNING, &mvm->status);
-	clear_bit(IWL_MVM_STATUS_ROC_AUX_RUNNING, &mvm->status);
 
 	synchronize_net();
 
@@ -82,9 +81,19 @@
 			mvmvif = iwl_mvm_vif_from_mac80211(mvm->p2p_device_vif);
 			iwl_mvm_flush_sta(mvm, &mvmvif->bcast_sta, true);
 		}
-	} else {
+	}
+
+	/*
+	 * Clear the ROC_AUX_RUNNING status bit.
+	 * This will cause the TX path to drop offchannel transmissions.
+	 * That would also be done by mac80211, but it is racy, in particular
+	 * in the case that the time event actually completed in the firmware
+	 * (which is handled in iwl_mvm_te_handle_notif).
+	 */
+	if (test_and_clear_bit(IWL_MVM_STATUS_ROC_AUX_RUNNING, &mvm->status)) {
 		/* do the same in case of hot spot 2.0 */
 		iwl_mvm_flush_sta(mvm, &mvm->aux_sta, true);
+
 		/* In newer version of this command an aux station is added only
 		 * in cases of dedicated tx queue and need to be removed in end
 		 * of use */
@@ -687,11 +696,14 @@
 	iwl_mvm_te_clear_data(mvm, te_data);
 	spin_unlock_bh(&mvm->time_event_lock);
 
-	/* When session protection is supported, the te_data->id field
+	/* When session protection is used, the te_data->id field
 	 * is reused to save session protection's configuration.
+	 * For AUX ROC, HOT_SPOT_CMD is used and the te_data->id field is set
+	 * to HOT_SPOT_CMD.
 	 */
 	if (fw_has_capa(&mvm->fw->ucode_capa,
-			IWL_UCODE_TLV_CAPA_SESSION_PROT_CMD)) {
+			IWL_UCODE_TLV_CAPA_SESSION_PROT_CMD) &&
+	    id != HOT_SPOT_CMD) {
 		if (mvmvif && id < SESSION_PROTECT_CONF_MAX_ID) {
 			/* Session protection is still ongoing. Cancel it */
 			iwl_mvm_cancel_session_protection(mvm, mvmvif, id);
@@ -1027,7 +1039,7 @@
 			iwl_mvm_p2p_roc_finished(mvm);
 		} else {
 			iwl_mvm_remove_aux_roc_te(mvm, mvmvif,
-						  &mvmvif->time_event_data);
+						  &mvmvif->hs_time_event_data);
 			iwl_mvm_roc_finished(mvm);
 		}
 
@@ -1158,15 +1170,10 @@
 			cpu_to_le32(FW_CMD_ID_AND_COLOR(mvmvif->id,
 							mvmvif->color)),
 		.action = cpu_to_le32(FW_CTXT_ACTION_ADD),
+		.conf_id = cpu_to_le32(SESSION_PROTECT_CONF_ASSOC),
 		.duration_tu = cpu_to_le32(MSEC_TO_TU(duration)),
 	};
 
-	/* The time_event_data.id field is reused to save session
-	 * protection's configuration.
-	 */
-	mvmvif->time_event_data.id = SESSION_PROTECT_CONF_ASSOC;
-	cmd.conf_id = cpu_to_le32(mvmvif->time_event_data.id);
-
 	lockdep_assert_held(&mvm->mutex);
 
 	spin_lock_bh(&mvm->time_event_lock);
@@ -1180,6 +1187,11 @@
 	}
 
 	iwl_mvm_te_clear_data(mvm, te_data);
+	/*
+	 * The time_event_data.id field is reused to save session
+	 * protection's configuration.
+	 */
+	te_data->id = le32_to_cpu(cmd.conf_id);
 	te_data->duration = le32_to_cpu(cmd.duration_tu);
 	te_data->vif = vif;
 	spin_unlock_bh(&mvm->time_event_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
@@ -268,7 +268,6 @@
 	int rate_idx = -1;
 	u8 rate_plcp;
 	u32 rate_flags = 0;
-	struct iwl_mvm_sta *mvmsta = iwl_mvm_sta_from_mac80211(sta);
 
 	/* info->control is only relevant for non HW rate control */
 	if (!ieee80211_hw_check(mvm->hw, HAS_RATE_CONTROL)) {
@@ -278,7 +277,8 @@
 			  "Got a HT rate (flags:0x%x/mcs:%d/fc:0x%x/state:%d) for a non data frame\n",
 			  info->control.rates[0].flags,
 			  info->control.rates[0].idx,
-			  le16_to_cpu(fc), mvmsta->sta_state);
+			  le16_to_cpu(fc),
+			  sta ? iwl_mvm_sta_from_mac80211(sta)->sta_state : -1);
 
 		rate_idx = info->control.rates[0].idx;
 	}
@@ -479,16 +479,20 @@
 			flags |= IWL_TX_FLAGS_ENCRYPT_DIS;
 
 		/*
-		 * For data packets rate info comes from the fw. Only
-		 * set rate/antenna during connection establishment or in case
-		 * no station is given.
+		 * For data and mgmt packets rate info comes from the fw. Only
+		 * set rate/antenna for injected frames with fixed rate, or
+		 * when no sta is given.
 		 */
-		if (!sta || !ieee80211_is_data(hdr->frame_control) ||
-		    mvmsta->sta_state < IEEE80211_STA_AUTHORIZED) {
+		if (unlikely(!sta ||
+			     info->control.flags & IEEE80211_TX_CTRL_RATE_INJECT)) {
 			flags |= IWL_TX_FLAGS_CMD_RATE;
 			rate_n_flags =
 				iwl_mvm_get_tx_rate_n_flags(mvm, info, sta,
 							    hdr->frame_control);
+		} else if (!ieee80211_is_data(hdr->frame_control) ||
+			   mvmsta->sta_state < IEEE80211_STA_AUTHORIZED) {
+			/* These are important frames */
+			flags |= IWL_TX_FLAGS_HIGH_PRI;
 		}
 
 		if (mvm->trans->trans_cfg->device_family >=
@@ -1150,6 +1154,7 @@
 	struct sk_buff_head mpdus_skbs;
 	unsigned int payload_len;
 	int ret;
+	struct sk_buff *orig_skb = skb;
 
 	if (WARN_ON_ONCE(!mvmsta))
 		return -1;
@@ -1182,8 +1187,17 @@
 
 		ret = iwl_mvm_tx_mpdu(mvm, skb, &info, sta);
 		if (ret) {
+			/* Free skbs created as part of TSO logic that have not yet been dequeued */
 			__skb_queue_purge(&mpdus_skbs);
-			return ret;
+			/* skb here is not necessarily same as skb that entered this method,
+			 * so free it explicitly.
+			 */
+			if (skb == orig_skb)
+				ieee80211_free_txskb(mvm->hw, skb);
+			else
+				kfree_skb(skb);
+			/* there was error, but we consumed skb one way or another, so return 0 */
+			return 0;
 		}
 	}
 
@@ -1422,7 +1436,7 @@
 	seq_ctl = le16_to_cpu(tx_resp->seq_ctl);
 
 	/* we can free until ssn % q.n_bd not inclusive */
-	iwl_trans_reclaim(mvm->trans, txq_id, ssn, &skbs);
+	iwl_trans_reclaim(mvm->trans, txq_id, ssn, &skbs, false);
 
 	while (!skb_queue_empty(&skbs)) {
 		struct sk_buff *skb = __skb_dequeue(&skbs);
@@ -1435,6 +1449,7 @@
 		iwl_trans_free_tx_cmd(mvm->trans, info->driver_data[1]);
 
 		memset(&info->status, 0, sizeof(info->status));
+		info->flags &= ~(IEEE80211_TX_STAT_ACK | IEEE80211_TX_STAT_TX_FILTERED);
 
 		/* inform mac80211 about what happened with the frame */
 		switch (status & TX_STATUS_MSK) {
@@ -1766,7 +1781,7 @@
 	 * block-ack window (we assume that they've been successfully
 	 * transmitted ... if not, it's too late anyway).
 	 */
-	iwl_trans_reclaim(mvm->trans, txq, index, &reclaimed_skbs);
+	iwl_trans_reclaim(mvm->trans, txq, index, &reclaimed_skbs, is_flush);
 
 	skb_queue_walk(&reclaimed_skbs, skb) {
 		struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
@@ -1780,6 +1795,8 @@
 		 */
 		if (!is_flush)
 			info->flags |= IEEE80211_TX_STAT_ACK;
+		else
+			info->flags &= ~IEEE80211_TX_STAT_ACK;
 	}
 
 	/*
@@ -2037,7 +2054,7 @@
 	WARN_ON(!iwl_mvm_has_new_tx_api(mvm));
 
 	if (iwl_fw_lookup_notif_ver(mvm->fw, LONG_GROUP, TXPATH_FLUSH, 0) > 0)
-		cmd.flags |= CMD_WANT_SKB;
+		cmd.flags |= CMD_WANT_SKB | CMD_SEND_IN_RFKILL;
 
 	IWL_DEBUG_TX_QUEUES(mvm, "flush for sta id %d tid mask 0x%x\n",
 			    sta_id, tids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/mvm/utils.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/mvm/utils.c
@@ -405,6 +405,9 @@
 
 	lockdep_assert_held(&mvm->mutex);
 
+	if (iwlmvm_mod_params.power_scheme != IWL_POWER_SCHEME_CAM)
+		return false;
+
 	if (num_of_ant(iwl_mvm_get_valid_rx_ant(mvm)) == 1)
 		return false;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
@@ -64,7 +64,8 @@
 		}
 		break;
 	default:
-		IWL_ERR(trans, "WRT: Invalid buffer destination\n");
+		IWL_DEBUG_FW(trans, "WRT: Invalid buffer destination (%d)\n",
+			     le32_to_cpu(fw_mon_cfg->buf_location));
 	}
 out:
 	if (dbg_flags)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/drv.c
@@ -210,6 +210,7 @@
 	{IWL_PCI_DEVICE(0x088E, 0x446A, iwl6035_2agn_sff_cfg)},
 	{IWL_PCI_DEVICE(0x088E, 0x4860, iwl6035_2agn_cfg)},
 	{IWL_PCI_DEVICE(0x088F, 0x5260, iwl6035_2agn_cfg)},
+	{IWL_PCI_DEVICE(0x088F, 0x526A, iwl6035_2agn_cfg)},
 
 /* 105 Series */
 	{IWL_PCI_DEVICE(0x0894, 0x0022, iwl105_bgn_cfg)},
@@ -931,9 +932,9 @@
 		      IWL_CFG_ANY, IWL_CFG_ANY, IWL_CFG_NO_CDB,
 		      iwl_qu_b0_hr1_b0, iwl_ax101_name),
 	_IWL_DEV_INFO(IWL_CFG_ANY, IWL_CFG_ANY,
-		      IWL_CFG_MAC_TYPE_QU, SILICON_C_STEP,
+		      IWL_CFG_MAC_TYPE_QU, SILICON_B_STEP,
 		      IWL_CFG_RF_TYPE_HR2, IWL_CFG_ANY,
-		      IWL_CFG_ANY, IWL_CFG_ANY, IWL_CFG_NO_CDB,
+		      IWL_CFG_NO_160, IWL_CFG_ANY, IWL_CFG_NO_CDB,
 		      iwl_qu_b0_hr_b0, iwl_ax203_name),
 
 	/* Qu C step */
@@ -945,7 +946,7 @@
 	_IWL_DEV_INFO(IWL_CFG_ANY, IWL_CFG_ANY,
 		      IWL_CFG_MAC_TYPE_QU, SILICON_C_STEP,
 		      IWL_CFG_RF_TYPE_HR2, IWL_CFG_ANY,
-		      IWL_CFG_ANY, IWL_CFG_ANY, IWL_CFG_NO_CDB,
+		      IWL_CFG_NO_160, IWL_CFG_ANY, IWL_CFG_NO_CDB,
 		      iwl_qu_c0_hr_b0, iwl_ax203_name),
 
 	/* QuZ */
@@ -1380,6 +1381,9 @@
 {
 	struct iwl_trans *trans = pci_get_drvdata(pdev);
 
+	if (!trans)
+		return;
+
 	iwl_drv_stop(trans->drv);
 
 	iwl_trans_pcie_free(trans);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/internal.h
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
- * Copyright (C) 2003-2015, 2018-2021 Intel Corporation
+ * Copyright (C) 2003-2015, 2018-2022 Intel Corporation
  * Copyright (C) 2013-2015 Intel Mobile Communications GmbH
  * Copyright (C) 2016-2017 Intel Deutschland GmbH
  */
@@ -104,6 +104,18 @@
 } __packed;
 
 /**
+ * struct iwl_rx_completion_desc_bz - Bz completion descriptor
+ * @rbid: unique tag of the received buffer
+ * @flags: flags (0: fragmented, all others: reserved)
+ * @reserved: reserved
+ */
+struct iwl_rx_completion_desc_bz {
+	__le16 rbid;
+	u8 flags;
+	u8 reserved[1];
+} __packed;
+
+/**
  * struct iwl_rxq - Rx queue
  * @id: queue index
  * @bd: driver's pointer to buffer of receive buffer descriptors (rbd).
@@ -133,11 +145,7 @@
 	int id;
 	void *bd;
 	dma_addr_t bd_dma;
-	union {
-		void *used_bd;
-		__le32 *bd_32;
-		struct iwl_rx_completion_desc *cd;
-	};
+	void *used_bd;
 	dma_addr_t used_bd_dma;
 	u32 read;
 	u32 write;
@@ -363,7 +371,7 @@
 
 	/* PCI bus related data */
 	struct pci_dev *pci_dev;
-	void __iomem *hw_base;
+	u8 __iomem *hw_base;
 
 	bool ucode_write_complete;
 	bool sx_complete;
@@ -472,6 +480,7 @@
 void iwl_pcie_rx_free(struct iwl_trans *trans);
 void iwl_pcie_free_rbs_pool(struct iwl_trans *trans);
 void iwl_pcie_rx_init_rxb_lists(struct iwl_rxq *rxq);
+void iwl_pcie_rx_napi_sync(struct iwl_trans *trans);
 void iwl_pcie_rxq_alloc_rbs(struct iwl_trans *trans, gfp_t priority,
 			    struct iwl_rxq *rxq);
 
@@ -719,7 +728,7 @@
 	}
 }
 
-void iwl_pcie_handle_rfkill_irq(struct iwl_trans *trans);
+void iwl_pcie_handle_rfkill_irq(struct iwl_trans *trans, bool from_irq);
 
 static inline bool iwl_is_rfkill_set(struct iwl_trans *trans)
 {
@@ -766,7 +775,7 @@
 	return (trans->dbg.dest_tlv || iwl_trans_dbg_ini_valid(trans));
 }
 
-void iwl_trans_pcie_rf_kill(struct iwl_trans *trans, bool state);
+void iwl_trans_pcie_rf_kill(struct iwl_trans *trans, bool state, bool from_irq);
 void iwl_trans_pcie_dump_regs(struct iwl_trans *trans);
 
 #ifdef CONFIG_IWLWIFI_DEBUGFS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/rx.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
 /*
- * Copyright (C) 2003-2014, 2018-2021 Intel Corporation
+ * Copyright (C) 2003-2014, 2018-2023 Intel Corporation
  * Copyright (C) 2013-2015 Intel Mobile Communications GmbH
  * Copyright (C) 2016-2017 Intel Deutschland GmbH
  */
@@ -652,23 +652,30 @@
 	iwl_pcie_rx_allocator(trans_pcie->trans);
 }
 
-static int iwl_pcie_free_bd_size(struct iwl_trans *trans, bool use_rx_td)
+static int iwl_pcie_free_bd_size(struct iwl_trans *trans)
 {
-	struct iwl_rx_transfer_desc *rx_td;
+	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210)
+		return sizeof(struct iwl_rx_transfer_desc);
 
-	if (use_rx_td)
-		return sizeof(*rx_td);
-	else
-		return trans->trans_cfg->mq_rx_supported ? sizeof(__le64) :
-			sizeof(__le32);
+	return trans->trans_cfg->mq_rx_supported ?
+			sizeof(__le64) : sizeof(__le32);
+}
+
+static int iwl_pcie_used_bd_size(struct iwl_trans *trans)
+{
+	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_BZ)
+		return sizeof(struct iwl_rx_completion_desc_bz);
+
+	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210)
+		return sizeof(struct iwl_rx_completion_desc);
+
+	return sizeof(__le32);
 }
 
 static void iwl_pcie_free_rxq_dma(struct iwl_trans *trans,
 				  struct iwl_rxq *rxq)
 {
-	bool use_rx_td = (trans->trans_cfg->device_family >=
-			  IWL_DEVICE_FAMILY_AX210);
-	int free_size = iwl_pcie_free_bd_size(trans, use_rx_td);
+	int free_size = iwl_pcie_free_bd_size(trans);
 
 	if (rxq->bd)
 		dma_free_coherent(trans->dev,
@@ -682,8 +689,8 @@
 
 	if (rxq->used_bd)
 		dma_free_coherent(trans->dev,
-				  (use_rx_td ? sizeof(*rxq->cd) :
-				   sizeof(__le32)) * rxq->queue_size,
+				  iwl_pcie_used_bd_size(trans) *
+					rxq->queue_size,
 				  rxq->used_bd, rxq->used_bd_dma);
 	rxq->used_bd_dma = 0;
 	rxq->used_bd = NULL;
@@ -707,7 +714,7 @@
 	else
 		rxq->queue_size = RX_QUEUE_SIZE;
 
-	free_size = iwl_pcie_free_bd_size(trans, use_rx_td);
+	free_size = iwl_pcie_free_bd_size(trans);
 
 	/*
 	 * Allocate the circular buffer of Read Buffer Descriptors
@@ -720,14 +727,15 @@
 
 	if (trans->trans_cfg->mq_rx_supported) {
 		rxq->used_bd = dma_alloc_coherent(dev,
-						  (use_rx_td ? sizeof(*rxq->cd) : sizeof(__le32)) * rxq->queue_size,
+						  iwl_pcie_used_bd_size(trans) *
+							rxq->queue_size,
 						  &rxq->used_bd_dma,
 						  GFP_KERNEL);
 		if (!rxq->used_bd)
 			goto err;
 	}
 
-	rxq->rb_stts = trans_pcie->base_rb_stts + rxq->id * rb_stts_size;
+	rxq->rb_stts = (u8 *)trans_pcie->base_rb_stts + rxq->id * rb_stts_size;
 	rxq->rb_stts_dma =
 		trans_pcie->base_rb_stts_dma + rxq->id * rb_stts_size;
 
@@ -1042,6 +1050,22 @@
 	return ret;
 }
 
+void iwl_pcie_rx_napi_sync(struct iwl_trans *trans)
+{
+	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+	int i;
+
+	if (unlikely(!trans_pcie->rxq))
+		return;
+
+	for (i = 0; i < trans->num_rx_queues; i++) {
+		struct iwl_rxq *rxq = &trans_pcie->rxq[i];
+
+		if (rxq && rxq->napi.poll)
+			napi_synchronize(&rxq->napi);
+	}
+}
+
 static int _iwl_pcie_rx_init(struct iwl_trans *trans)
 {
 	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
@@ -1356,7 +1380,7 @@
 		 * if it is true then one of the handlers took the page.
 		 */
 
-		if (reclaim) {
+		if (reclaim && txq) {
 			u16 sequence = le16_to_cpu(pkt->hdr.sequence);
 			int index = SEQ_TO_INDEX(sequence);
 			int cmd_index = iwl_txq_get_cmd_index(txq, index);
@@ -1419,6 +1443,7 @@
 	u16 vid;
 
 	BUILD_BUG_ON(sizeof(struct iwl_rx_completion_desc) != 32);
+	BUILD_BUG_ON(sizeof(struct iwl_rx_completion_desc_bz) != 4);
 
 	if (!trans->trans_cfg->mq_rx_supported) {
 		rxb = rxq->queue[i];
@@ -1426,11 +1451,20 @@
 		return rxb;
 	}
 
-	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210) {
-		vid = le16_to_cpu(rxq->cd[i].rbid);
-		*join = rxq->cd[i].flags & IWL_RX_CD_FLAGS_FRAGMENTED;
+	if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_BZ) {
+		struct iwl_rx_completion_desc_bz *cd = rxq->used_bd;
+
+		vid = le16_to_cpu(cd[i].rbid);
+		*join = cd[i].flags & IWL_RX_CD_FLAGS_FRAGMENTED;
+	} else if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210) {
+		struct iwl_rx_completion_desc *cd = rxq->used_bd;
+
+		vid = le16_to_cpu(cd[i].rbid);
+		*join = cd[i].flags & IWL_RX_CD_FLAGS_FRAGMENTED;
 	} else {
-		vid = le32_to_cpu(rxq->bd_32[i]) & 0x0FFF; /* 12-bit VID */
+		__le32 *cd = rxq->used_bd;
+
+		vid = le32_to_cpu(cd[i]) & 0x0FFF; /* 12-bit VID */
 	}
 
 	if (!vid || vid > RX_POOL_SIZE(trans_pcie->num_rx_bufs))
@@ -1601,18 +1635,22 @@
 	struct msix_entry *entry = dev_id;
 	struct iwl_trans_pcie *trans_pcie = iwl_pcie_get_trans_pcie(entry);
 	struct iwl_trans *trans = trans_pcie->trans;
-	struct iwl_rxq *rxq = &trans_pcie->rxq[entry->entry];
+	struct iwl_rxq *rxq;
 
 	trace_iwlwifi_dev_irq_msix(trans->dev, entry, false, 0, 0);
 
 	if (WARN_ON(entry->entry >= trans->num_rx_queues))
 		return IRQ_NONE;
 
-	if (WARN_ONCE(!rxq,
-		      "[%d] Got MSI-X interrupt before we have Rx queues",
-		      entry->entry))
+	if (!trans_pcie->rxq) {
+		if (net_ratelimit())
+			IWL_ERR(trans,
+				"[%d] Got MSI-X interrupt before we have Rx queues\n",
+				entry->entry);
 		return IRQ_NONE;
+	}
 
+	rxq = &trans_pcie->rxq[entry->entry];
 	lock_map_acquire(&trans->sync_cmd_lockdep_map);
 	IWL_DEBUG_ISR(trans, "[%d] Got interrupt\n", entry->entry);
 
@@ -1742,7 +1780,7 @@
 	return inta;
 }
 
-void iwl_pcie_handle_rfkill_irq(struct iwl_trans *trans)
+void iwl_pcie_handle_rfkill_irq(struct iwl_trans *trans, bool from_irq)
 {
 	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
 	struct isr_statistics *isr_stats = &trans_pcie->isr_stats;
@@ -1766,7 +1804,7 @@
 	isr_stats->rfkill++;
 
 	if (prev != report)
-		iwl_trans_pcie_rf_kill(trans, report);
+		iwl_trans_pcie_rf_kill(trans, report, from_irq);
 	mutex_unlock(&trans_pcie->mutex);
 
 	if (hw_rfkill) {
@@ -1906,7 +1944,7 @@
 
 	/* HW RF KILL switch toggled */
 	if (inta & CSR_INT_BIT_RF_KILL) {
-		iwl_pcie_handle_rfkill_irq(trans);
+		iwl_pcie_handle_rfkill_irq(trans, true);
 		handled |= CSR_INT_BIT_RF_KILL;
 	}
 
@@ -2261,7 +2299,12 @@
 		}
 	}
 
-	if (inta_hw & MSIX_HW_INT_CAUSES_REG_WAKEUP) {
+	/*
+	 * In some rare cases when the HW is in a bad state, we may
+	 * get this interrupt too early, when prph_info is still NULL.
+	 * So make sure that it's not NULL to prevent crashing.
+	 */
+	if (inta_hw & MSIX_HW_INT_CAUSES_REG_WAKEUP && trans_pcie->prph_info) {
 		u32 sleep_notif =
 			le32_to_cpu(trans_pcie->prph_info->sleep_notif);
 		if (sleep_notif == IWL_D3_SLEEP_STATUS_SUSPEND ||
@@ -2289,7 +2332,7 @@
 
 	/* HW RF KILL switch toggled */
 	if (inta_hw & MSIX_HW_INT_CAUSES_REG_RF_KILL)
-		iwl_pcie_handle_rfkill_irq(trans);
+		iwl_pcie_handle_rfkill_irq(trans, true);
 
 	if (inta_hw & MSIX_HW_INT_CAUSES_REG_HW_ERR) {
 		IWL_ERR(trans,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/trans-gen2.c
@@ -165,6 +165,8 @@
 	if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
 		IWL_DEBUG_INFO(trans,
 			       "DEVICE_ENABLED bit was set and is now cleared\n");
+		iwl_pcie_synchronize_irqs(trans);
+		iwl_pcie_rx_napi_sync(trans);
 		iwl_txq_gen2_tx_free(trans);
 		iwl_pcie_rx_stop(trans);
 	}
@@ -408,8 +410,7 @@
 	/* This may fail if AMT took ownership of the device */
 	if (iwl_pcie_prepare_card_hw(trans)) {
 		IWL_WARN(trans, "Exit HW not ready\n");
-		ret = -EIO;
-		goto out;
+		return -EIO;
 	}
 
 	iwl_enable_rfkill_int(trans);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/trans.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/trans.c
@@ -581,7 +581,6 @@
 int iwl_pcie_prepare_card_hw(struct iwl_trans *trans)
 {
 	int ret;
-	int t = 0;
 	int iter;
 
 	IWL_DEBUG_INFO(trans, "iwl_trans_prepare_card_hw enter\n");
@@ -596,6 +595,8 @@
 	usleep_range(1000, 2000);
 
 	for (iter = 0; iter < 10; iter++) {
+		int t = 0;
+
 		/* If HW is not ready, prepare the conditions to check again */
 		iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG,
 			    CSR_HW_IF_CONFIG_REG_PREPARE);
@@ -1045,7 +1046,7 @@
 	report = test_bit(STATUS_RFKILL_OPMODE, &trans->status);
 
 	if (prev != report)
-		iwl_trans_pcie_rf_kill(trans, report);
+		iwl_trans_pcie_rf_kill(trans, report, false);
 
 	return hw_rfkill;
 }
@@ -1169,7 +1170,7 @@
 	trans_pcie->hw_mask = trans_pcie->hw_init_mask;
 }
 
-static void _iwl_trans_pcie_stop_device(struct iwl_trans *trans)
+static void _iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool from_irq)
 {
 	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
 
@@ -1196,6 +1197,9 @@
 	if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
 		IWL_DEBUG_INFO(trans,
 			       "DEVICE_ENABLED bit was set and is now cleared\n");
+		if (!from_irq)
+			iwl_pcie_synchronize_irqs(trans);
+		iwl_pcie_rx_napi_sync(trans);
 		iwl_pcie_tx_stop(trans);
 		iwl_pcie_rx_stop(trans);
 
@@ -1273,8 +1277,7 @@
 	/* This may fail if AMT took ownership of the device */
 	if (iwl_pcie_prepare_card_hw(trans)) {
 		IWL_WARN(trans, "Exit HW not ready\n");
-		ret = -EIO;
-		goto out;
+		return -EIO;
 	}
 
 	iwl_enable_rfkill_int(trans);
@@ -1383,7 +1386,7 @@
 		clear_bit(STATUS_RFKILL_OPMODE, &trans->status);
 	}
 	if (hw_rfkill != was_in_rfkill)
-		iwl_trans_pcie_rf_kill(trans, hw_rfkill);
+		iwl_trans_pcie_rf_kill(trans, hw_rfkill, false);
 }
 
 static void iwl_trans_pcie_stop_device(struct iwl_trans *trans)
@@ -1398,12 +1401,12 @@
 	mutex_lock(&trans_pcie->mutex);
 	trans_pcie->opmode_down = true;
 	was_in_rfkill = test_bit(STATUS_RFKILL_OPMODE, &trans->status);
-	_iwl_trans_pcie_stop_device(trans);
+	_iwl_trans_pcie_stop_device(trans, false);
 	iwl_trans_pcie_handle_stop_rfkill(trans, was_in_rfkill);
 	mutex_unlock(&trans_pcie->mutex);
 }
 
-void iwl_trans_pcie_rf_kill(struct iwl_trans *trans, bool state)
+void iwl_trans_pcie_rf_kill(struct iwl_trans *trans, bool state, bool from_irq)
 {
 	struct iwl_trans_pcie __maybe_unused *trans_pcie =
 		IWL_TRANS_GET_PCIE_TRANS(trans);
@@ -1416,7 +1419,7 @@
 		if (trans->trans_cfg->gen2)
 			_iwl_trans_pcie_gen2_stop_device(trans);
 		else
-			_iwl_trans_pcie_stop_device(trans);
+			_iwl_trans_pcie_stop_device(trans, from_irq);
 	}
 }
 
@@ -1987,12 +1990,18 @@
 		container_of(wk, struct iwl_trans_pcie_removal, work);
 	struct pci_dev *pdev = removal->pdev;
 	static char *prop[] = {"EVENT=INACCESSIBLE", NULL};
+	struct pci_bus *bus = pdev->bus;
 
 	dev_err(&pdev->dev, "Device gone - attempting removal\n");
 	kobject_uevent_env(&pdev->dev.kobj, KOBJ_CHANGE, prop);
 	pci_lock_rescan_remove();
 	pci_dev_put(pdev);
 	pci_stop_and_remove_bus_device(pdev);
+	if (bus) {
+		if (bus->parent)
+			bus = bus->parent;
+		pci_rescan_bus(bus);
+	}
 	pci_unlock_rescan_remove();
 
 	kfree(removal);
@@ -2739,7 +2748,7 @@
 	IWL_WARN(trans, "changing debug rfkill %d->%d\n",
 		 trans_pcie->debug_rfkill, new_value);
 	trans_pcie->debug_rfkill = new_value;
-	iwl_pcie_handle_rfkill_irq(trans);
+	iwl_pcie_handle_rfkill_irq(trans, false);
 
 	return count;
 }
@@ -2778,7 +2787,7 @@
 				  void *buf, ssize_t *size,
 				  ssize_t *bytes_copied)
 {
-	int buf_size_left = count - *bytes_copied;
+	ssize_t buf_size_left = count - *bytes_copied;
 
 	buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
 	if (*size > buf_size_left)
@@ -2798,7 +2807,7 @@
 {
 	struct iwl_trans *trans = file->private_data;
 	struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
-	void *cpu_addr = (void *)trans->dbg.fw_mon.block, *curr_buf;
+	u8 *cpu_addr = (void *)trans->dbg.fw_mon.block, *curr_buf;
 	struct cont_rec *data = &trans_pcie->fw_mon_data;
 	u32 write_ptr_addr, wrap_cnt_addr, write_ptr, wrap_cnt;
 	ssize_t size, bytes_copied = 0;
@@ -2958,7 +2967,7 @@
 	struct iwl_rxq *rxq = &trans_pcie->rxq[0];
 	u32 i, r, j, rb_len = 0;
 
-	spin_lock(&rxq->lock);
+	spin_lock_bh(&rxq->lock);
 
 	r = le16_to_cpu(iwl_get_closed_rb_stts(trans, rxq)) & 0x0FFF;
 
@@ -2982,7 +2991,7 @@
 		*data = iwl_fw_error_next_data(*data);
 	}
 
-	spin_unlock(&rxq->lock);
+	spin_unlock_bh(&rxq->lock);
 
 	return rb_len;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/pcie/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/pcie/tx.c
@@ -154,7 +154,7 @@
 	void *tfd;
 	u32 num_tbs;
 
-	tfd = txq->tfds + trans->txqs.tfd.size * txq->write_ptr;
+	tfd = (u8 *)txq->tfds + trans->txqs.tfd.size * txq->write_ptr;
 
 	if (reset)
 		memset(tfd, 0, trans->txqs.tfd.size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/queue/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/queue/tx.c
@@ -189,7 +189,7 @@
 		return NULL;
 
 	/* set the chaining pointer to the previous page if there */
-	*(void **)(page_address(ret) + PAGE_SIZE - sizeof(void *)) = *page_ptr;
+	*(void **)((u8 *)page_address(ret) + PAGE_SIZE - sizeof(void *)) = *page_ptr;
 	*page_ptr = ret;
 
 	return ret;
@@ -314,7 +314,7 @@
 		return NULL;
 	p->pos = page_address(p->page);
 	/* set the chaining pointer to NULL */
-	*(void **)(page_address(p->page) + PAGE_SIZE - sizeof(void *)) = NULL;
+	*(void **)((u8 *)page_address(p->page) + PAGE_SIZE - sizeof(void *)) = NULL;
 out:
 	*page_ptr = p->page;
 	get_page(p->page);
@@ -963,7 +963,7 @@
 	while (next) {
 		struct page *tmp = next;
 
-		next = *(void **)(page_address(next) + PAGE_SIZE -
+		next = *(void **)((u8 *)page_address(next) + PAGE_SIZE -
 				  sizeof(void *));
 		__free_page(tmp);
 	}
@@ -1072,6 +1072,7 @@
 	return 0;
 err_free_tfds:
 	dma_free_coherent(trans->dev, tfd_sz, txq->tfds, txq->dma_addr);
+	txq->tfds = NULL;
 error:
 	if (txq->entries && cmd_queue)
 		for (i = 0; i < slots_num; i++)
@@ -1519,7 +1520,7 @@
 
 /* Frees buffers until index _not_ inclusive */
 void iwl_txq_reclaim(struct iwl_trans *trans, int txq_id, int ssn,
-		     struct sk_buff_head *skbs)
+		     struct sk_buff_head *skbs, bool is_flush)
 {
 	struct iwl_txq *txq = trans->txqs.txq[txq_id];
 	int tfd_num = iwl_txq_get_cmd_index(txq, ssn);
@@ -1590,9 +1591,11 @@
 	if (iwl_txq_space(trans, txq) > txq->low_mark &&
 	    test_bit(txq_id, trans->txqs.queue_stopped)) {
 		struct sk_buff_head overflow_skbs;
+		struct sk_buff *skb;
 
 		__skb_queue_head_init(&overflow_skbs);
-		skb_queue_splice_init(&txq->overflow_q, &overflow_skbs);
+		skb_queue_splice_init(&txq->overflow_q,
+				      is_flush ? skbs : &overflow_skbs);
 
 		/*
 		 * We are going to transmit from the overflow queue.
@@ -1612,8 +1615,7 @@
 		 */
 		spin_unlock_bh(&txq->lock);
 
-		while (!skb_queue_empty(&overflow_skbs)) {
-			struct sk_buff *skb = __skb_dequeue(&overflow_skbs);
+		while ((skb = __skb_dequeue(&overflow_skbs))) {
 			struct iwl_device_tx_cmd *dev_cmd_ptr;
 
 			dev_cmd_ptr = *(void **)((u8 *)skb->cb +
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intel/iwlwifi/queue/tx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intel/iwlwifi/queue/tx.h
@@ -41,7 +41,7 @@
 	if (trans->trans_cfg->use_tfh)
 		idx = iwl_txq_get_cmd_index(txq, idx);
 
-	return txq->tfds + trans->txqs.tfd.size * idx;
+	return (u8 *)txq->tfds + trans->txqs.tfd.size * idx;
 }
 
 int iwl_txq_alloc(struct iwl_trans *trans, struct iwl_txq *txq, int slots_num,
@@ -174,7 +174,7 @@
 				      struct iwl_txq *txq, u16 byte_cnt,
 				      int num_tbs);
 void iwl_txq_reclaim(struct iwl_trans *trans, int txq_id, int ssn,
-		     struct sk_buff_head *skbs);
+		     struct sk_buff_head *skbs, bool is_flush);
 void iwl_txq_set_q_ptrs(struct iwl_trans *trans, int txq_id, int ptr);
 void iwl_trans_txq_freeze_timer(struct iwl_trans *trans, unsigned long txqs,
 				bool freeze);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intersil/orinoco/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intersil/orinoco/hw.c
@@ -931,6 +931,8 @@
 			err = hermes_write_wordrec(hw, USER_BAP,
 					HERMES_RID_CNFAUTHENTICATION_AGERE,
 					auth_flag);
+			if (err)
+				return err;
 		}
 		err = hermes_write_wordrec(hw, USER_BAP,
 					   HERMES_RID_CNFWEPENABLED_AGERE,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intersil/orinoco/orinoco_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intersil/orinoco/orinoco_cs.c
@@ -96,6 +96,7 @@
 {
 	struct orinoco_private *priv;
 	struct orinoco_pccard *card;
+	int ret;
 
 	priv = alloc_orinocodev(sizeof(*card), &link->dev,
 				orinoco_cs_hard_reset, NULL);
@@ -107,8 +108,16 @@
 	card->p_dev = link;
 	link->priv = priv;
 
-	return orinoco_cs_config(link);
-}				/* orinoco_cs_attach */
+	ret = orinoco_cs_config(link);
+	if (ret)
+		goto err_free_orinocodev;
+
+	return 0;
+
+err_free_orinocodev:
+	free_orinocodev(priv);
+	return ret;
+}
 
 static void orinoco_cs_detach(struct pcmcia_device *link)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intersil/orinoco/spectrum_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intersil/orinoco/spectrum_cs.c
@@ -157,6 +157,7 @@
 {
 	struct orinoco_private *priv;
 	struct orinoco_pccard *card;
+	int ret;
 
 	priv = alloc_orinocodev(sizeof(*card), &link->dev,
 				spectrum_cs_hard_reset,
@@ -169,8 +170,16 @@
 	card->p_dev = link;
 	link->priv = priv;
 
-	return spectrum_cs_config(link);
-}				/* spectrum_cs_attach */
+	ret = spectrum_cs_config(link);
+	if (ret)
+		goto err_free_orinocodev;
+
+	return 0;
+
+err_free_orinocodev:
+	free_orinocodev(priv);
+	return ret;
+}
 
 static void spectrum_cs_detach(struct pcmcia_device *link)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intersil/p54/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intersil/p54/main.c
@@ -682,7 +682,7 @@
 	 * queues have already been stopped and no new frames can sneak
 	 * up from behind.
 	 */
-	while ((total = p54_flush_count(priv) && i--)) {
+	while ((total = p54_flush_count(priv)) && i--) {
 		/* waste time */
 		msleep(20);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/intersil/p54/p54spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/intersil/p54/p54spi.c
@@ -164,7 +164,7 @@
 
 	ret = p54_parse_firmware(dev, priv->firmware);
 	if (ret) {
-		release_firmware(priv->firmware);
+		/* the firmware is released by the caller */
 		return ret;
 	}
 
@@ -623,7 +623,7 @@
 	gpio_direction_input(p54spi_gpio_irq);
 
 	ret = request_irq(gpio_to_irq(p54spi_gpio_irq),
-			  p54spi_interrupt, 0, "p54spi",
+			  p54spi_interrupt, IRQF_NO_AUTOEN, "p54spi",
 			  priv->spi);
 	if (ret < 0) {
 		dev_err(&priv->spi->dev, "request_irq() failed");
@@ -632,8 +632,6 @@
 
 	irq_set_irq_type(gpio_to_irq(p54spi_gpio_irq), IRQ_TYPE_EDGE_RISING);
 
-	disable_irq(gpio_to_irq(p54spi_gpio_irq));
-
 	INIT_WORK(&priv->work, p54spi_work);
 	init_completion(&priv->fw_comp);
 	INIT_LIST_HEAD(&priv->tx_pending);
@@ -659,6 +657,7 @@
 	return 0;
 
 err_free_common:
+	release_firmware(priv->firmware);
 	free_irq(gpio_to_irq(p54spi_gpio_irq), spi);
 err_free_gpio_irq:
 	gpio_free(p54spi_gpio_irq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mac80211_hwsim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mac80211_hwsim.c
@@ -663,7 +663,7 @@
 	bool ps_poll_pending;
 	struct dentry *debugfs;
 
-	uintptr_t pending_cookie;
+	atomic_t pending_cookie;
 	struct sk_buff_head pending;	/* packets pending */
 	/*
 	 * Only radios in the same group can communicate together (the
@@ -845,6 +845,7 @@
 	struct hwsim_vif_priv *vp = (void *)vif->drv_priv;
 	struct sk_buff *skb;
 	struct ieee80211_hdr *hdr;
+	struct ieee80211_tx_info *cb;
 
 	if (!vp->assoc)
 		return;
@@ -866,6 +867,10 @@
 	memcpy(hdr->addr2, mac, ETH_ALEN);
 	memcpy(hdr->addr3, vp->bssid, ETH_ALEN);
 
+	cb = IEEE80211_SKB_CB(skb);
+	cb->control.rates[0].count = 1;
+	cb->control.rates[1].idx = -1;
+
 	rcu_read_lock();
 	mac80211_hwsim_tx_frame(data->hw, skb,
 				rcu_dereference(vif->chanctx_conf)->def.chan);
@@ -1339,8 +1344,7 @@
 		goto nla_put_failure;
 
 	/* We create a cookie to identify this skb */
-	data->pending_cookie++;
-	cookie = data->pending_cookie;
+	cookie = atomic_inc_return(&data->pending_cookie);
 	info->rate_driver_data[0] = (void *)cookie;
 	if (nla_put_u64_64bit(skb, HWSIM_ATTR_COOKIE, cookie, HWSIM_ATTR_PAD))
 		goto nla_put_failure;
@@ -2336,9 +2340,21 @@
 			if (req->ie_len)
 				skb_put_data(probe, req->ie, req->ie_len);
 
+			rcu_read_lock();
+			if (!ieee80211_tx_prepare_skb(hwsim->hw,
+						      hwsim->hw_scan_vif,
+						      probe,
+						      hwsim->tmp_chan->band,
+						      NULL)) {
+				rcu_read_unlock();
+				kfree_skb(probe);
+				continue;
+			}
+
 			local_bh_disable();
 			mac80211_hwsim_tx_frame(hwsim->hw, probe,
 						hwsim->tmp_chan);
+			rcu_read_unlock();
 			local_bh_enable();
 		}
 	}
@@ -2599,7 +2615,7 @@
 					  u32 sset, u8 *data)
 {
 	if (sset == ETH_SS_STATS)
-		memcpy(data, *mac80211_hwsim_gstrings_stats,
+		memcpy(data, mac80211_hwsim_gstrings_stats,
 		       sizeof(mac80211_hwsim_gstrings_stats));
 }
 
@@ -3570,6 +3586,7 @@
 	const u8 *src;
 	unsigned int hwsim_flags;
 	int i;
+	unsigned long flags;
 	bool found = false;
 
 	if (!info->attrs[HWSIM_ATTR_ADDR_TRANSMITTER] ||
@@ -3597,18 +3614,20 @@
 	}
 
 	/* look for the skb matching the cookie passed back from user */
+	spin_lock_irqsave(&data2->pending.lock, flags);
 	skb_queue_walk_safe(&data2->pending, skb, tmp) {
-		u64 skb_cookie;
+		uintptr_t skb_cookie;
 
 		txi = IEEE80211_SKB_CB(skb);
-		skb_cookie = (u64)(uintptr_t)txi->rate_driver_data[0];
+		skb_cookie = (uintptr_t)txi->rate_driver_data[0];
 
 		if (skb_cookie == ret_skb_cookie) {
-			skb_unlink(skb, &data2->pending);
+			__skb_unlink(skb, &data2->pending);
 			found = true;
 			break;
 		}
 	}
+	spin_unlock_irqrestore(&data2->pending.lock, flags);
 
 	/* not found */
 	if (!found)
@@ -3641,6 +3660,10 @@
 		}
 		txi->flags |= IEEE80211_TX_STAT_ACK;
 	}
+
+	if (hwsim_flags & HWSIM_TX_CTL_NO_ACK)
+		txi->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
+
 	ieee80211_tx_status_irqsafe(data2->hw, skb);
 	return 0;
 out:
@@ -3670,14 +3693,15 @@
 	frame_data_len = nla_len(info->attrs[HWSIM_ATTR_FRAME]);
 	frame_data = (void *)nla_data(info->attrs[HWSIM_ATTR_FRAME]);
 
+	if (frame_data_len < sizeof(struct ieee80211_hdr_3addr) ||
+	    frame_data_len > IEEE80211_MAX_DATA_LEN)
+		goto err;
+
 	/* Allocate new skb here */
 	skb = alloc_skb(frame_data_len, GFP_KERNEL);
 	if (skb == NULL)
 		goto err;
 
-	if (frame_data_len > IEEE80211_MAX_DATA_LEN)
-		goto err;
-
 	/* Copy the data */
 	skb_put_data(skb, frame_data, frame_data_len);
 
@@ -3731,6 +3755,8 @@
 
 	rx_status.band = channel->band;
 	rx_status.rate_idx = nla_get_u32(info->attrs[HWSIM_ATTR_RX_RATE]);
+	if (rx_status.rate_idx >= data2->hw->wiphy->bands[rx_status.band]->n_bitrates)
+		goto out;
 	rx_status.signal = nla_get_u32(info->attrs[HWSIM_ATTR_SIGNAL]);
 
 	hdr = (void *)skb->data;
@@ -4260,6 +4286,10 @@
 
 	nlh = nlmsg_hdr(skb);
 	gnlh = nlmsg_data(nlh);
+
+	if (skb->len < nlh->nlmsg_len)
+		return -EINVAL;
+
 	err = genlmsg_parse(nlh, &hwsim_genl_family, tb, HWSIM_ATTR_MAX,
 			    hwsim_genl_policy, NULL);
 	if (err) {
@@ -4302,7 +4332,8 @@
 	spin_unlock_irqrestore(&hwsim_virtio_lock, flags);
 
 	skb->data = skb->head;
-	skb_set_tail_pointer(skb, len);
+	skb_reset_tail_pointer(skb);
+	skb_put(skb, len);
 	hwsim_virtio_handle_cmd(skb);
 
 	spin_lock_irqsave(&hwsim_virtio_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/libertas/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/libertas/Kconfig
@@ -2,8 +2,6 @@
 config LIBERTAS
 	tristate "Marvell 8xxx Libertas WLAN driver support"
 	depends on CFG80211
-	select WIRELESS_EXT
-	select WEXT_SPY
 	select LIB80211
 	select FW_LOADER
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/libertas/cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/libertas/cmd.c
@@ -1133,7 +1133,7 @@
 		if (!cmdarray[i].cmdbuf) {
 			lbs_deb_host("ALLOC_CMD_BUF: ptempvirtualaddr is NULL\n");
 			ret = -1;
-			goto done;
+			goto free_cmd_array;
 		}
 	}
 
@@ -1141,8 +1141,17 @@
 		init_waitqueue_head(&cmdarray[i].cmdwait_q);
 		lbs_cleanup_and_insert_cmd(priv, &cmdarray[i]);
 	}
-	ret = 0;
+	return 0;
 
+free_cmd_array:
+	for (i = 0; i < LBS_NUM_CMD_BUFFERS; i++) {
+		if (cmdarray[i].cmdbuf) {
+			kfree(cmdarray[i].cmdbuf);
+			cmdarray[i].cmdbuf = NULL;
+		}
+	}
+	kfree(priv->cmd_array);
+	priv->cmd_array = NULL;
 done:
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/libertas/cmdresp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/libertas/cmdresp.c
@@ -48,7 +48,7 @@
 
 	/* Free Tx and Rx packets */
 	spin_lock_irqsave(&priv->driver_lock, flags);
-	kfree_skb(priv->currenttxskb);
+	dev_kfree_skb_irq(priv->currenttxskb);
 	priv->currenttxskb = NULL;
 	priv->tx_pending_len = 0;
 	spin_unlock_irqrestore(&priv->driver_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/libertas/if_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/libertas/if_usb.c
@@ -287,11 +287,13 @@
 	return 0;
 
 err_get_fw:
+	usb_put_dev(udev);
 	lbs_remove_card(priv);
 err_add_card:
 	if_usb_reset_device(cardp);
 dealloc:
 	if_usb_free(cardp);
+	kfree(cardp);
 
 error:
 	return r;
@@ -316,6 +318,7 @@
 
 	/* Unlink and free urb */
 	if_usb_free(cardp);
+	kfree(cardp);
 
 	usb_set_intfdata(intf, NULL);
 	usb_put_dev(interface_to_usbdev(intf));
@@ -634,7 +637,7 @@
 	priv->resp_len[i] = (recvlength - MESSAGE_HEADER_LEN);
 	memcpy(priv->resp_buf[i], recvbuff + MESSAGE_HEADER_LEN,
 		priv->resp_len[i]);
-	kfree_skb(skb);
+	dev_kfree_skb_irq(skb);
 	lbs_notify_command_response(priv, i);
 
 	spin_unlock_irqrestore(&priv->driver_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/libertas/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/libertas/main.c
@@ -217,7 +217,7 @@
 
 	spin_lock_irqsave(&priv->driver_lock, flags);
 	priv->iface_running = false;
-	kfree_skb(priv->currenttxskb);
+	dev_kfree_skb_irq(priv->currenttxskb);
 	priv->currenttxskb = NULL;
 	priv->tx_pending_len = 0;
 	spin_unlock_irqrestore(&priv->driver_lock, flags);
@@ -870,6 +870,7 @@
 	ret = kfifo_alloc(&priv->event_fifo, sizeof(u32) * 16, GFP_KERNEL);
 	if (ret) {
 		pr_err("Out of memory allocating event FIFO buffer\n");
+		lbs_free_cmd_buffer(priv);
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/libertas_tf/if_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/libertas_tf/if_usb.c
@@ -230,6 +230,7 @@
 
 dealloc:
 	if_usb_free(cardp);
+	kfree(cardp);
 error:
 lbtf_deb_leave(LBTF_DEB_MAIN);
 	return -ENOMEM;
@@ -254,6 +255,7 @@
 
 	/* Unlink and free urb */
 	if_usb_free(cardp);
+	kfree(cardp);
 
 	usb_set_intfdata(intf, NULL);
 	usb_put_dev(interface_to_usbdev(intf));
@@ -611,7 +613,7 @@
 	spin_lock_irqsave(&priv->driver_lock, flags);
 	memcpy(priv->cmd_resp_buff, recvbuff + MESSAGE_HEADER_LEN,
 	       recvlength - MESSAGE_HEADER_LEN);
-	kfree_skb(skb);
+	dev_kfree_skb_irq(skb);
 	lbtf_cmd_response_rx(priv);
 	spin_unlock_irqrestore(&priv->driver_lock, flags);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/11h.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/11h.c
@@ -303,5 +303,7 @@
 
 	mwifiex_dbg(priv->adapter, MSG,
 		    "indicating channel switch completion to kernel\n");
+	mutex_lock(&priv->wdev.mtx);
 	cfg80211_ch_switch_notify(priv->netdev, &priv->dfs_chandef);
+	mutex_unlock(&priv->wdev.mtx);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/11n.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/11n.c
@@ -657,14 +657,15 @@
 	uint16_t del_ba_param_set;
 
 	memset(&delba, 0, sizeof(delba));
-	delba.del_ba_param_set = cpu_to_le16(tid << DELBA_TID_POS);
 
-	del_ba_param_set = le16_to_cpu(delba.del_ba_param_set);
+	del_ba_param_set = tid << DELBA_TID_POS;
+
 	if (initiator)
 		del_ba_param_set |= IEEE80211_DELBA_PARAM_INITIATOR_MASK;
 	else
 		del_ba_param_set &= ~IEEE80211_DELBA_PARAM_INITIATOR_MASK;
 
+	delba.del_ba_param_set = cpu_to_le16(del_ba_param_set);
 	memcpy(&delba.peer_mac_addr, peer_mac, ETH_ALEN);
 
 	/* We don't wait for the response of this command */
@@ -889,7 +890,7 @@
  */
 void mwifiex_update_ampdu_txwinsize(struct mwifiex_adapter *adapter)
 {
-	u8 i;
+	u8 i, j;
 	u32 tx_win_size;
 	struct mwifiex_private *priv;
 
@@ -920,8 +921,8 @@
 		if (tx_win_size != priv->add_ba_param.tx_win_size) {
 			if (!priv->media_connected)
 				continue;
-			for (i = 0; i < MAX_NUM_TID; i++)
-				mwifiex_send_delba_txbastream_tbl(priv, i);
+			for (j = 0; j < MAX_NUM_TID; j++)
+				mwifiex_send_delba_txbastream_tbl(priv, j);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/11n_rxreorder.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/11n_rxreorder.c
@@ -933,6 +933,14 @@
 	while (tlv_buf_left >= sizeof(*tlv_rxba)) {
 		tlv_type = le16_to_cpu(tlv_rxba->header.type);
 		tlv_len  = le16_to_cpu(tlv_rxba->header.len);
+		if (size_add(sizeof(tlv_rxba->header), tlv_len) > tlv_buf_left) {
+			mwifiex_dbg(priv->adapter, WARN,
+				    "TLV size (%zu) overflows event_buf buf_left=%d\n",
+				    size_add(sizeof(tlv_rxba->header), tlv_len),
+				    tlv_buf_left);
+			return;
+		}
+
 		if (tlv_type != TLV_TYPE_RXBA_SYNC) {
 			mwifiex_dbg(priv->adapter, ERROR,
 				    "Wrong TLV id=0x%x\n", tlv_type);
@@ -941,6 +949,14 @@
 
 		tlv_seq_num = le16_to_cpu(tlv_rxba->seq_num);
 		tlv_bitmap_len = le16_to_cpu(tlv_rxba->bitmap_len);
+		if (size_add(sizeof(*tlv_rxba), tlv_bitmap_len) > tlv_buf_left) {
+			mwifiex_dbg(priv->adapter, WARN,
+				    "TLV size (%zu) overflows event_buf buf_left=%d\n",
+				    size_add(sizeof(*tlv_rxba), tlv_bitmap_len),
+				    tlv_buf_left);
+			return;
+		}
+
 		mwifiex_dbg(priv->adapter, INFO,
 			    "%pM tid=%d seq_num=%d bitmap_len=%d\n",
 			    tlv_rxba->mac, tlv_rxba->tid, tlv_seq_num,
@@ -977,8 +993,8 @@
 			}
 		}
 
-		tlv_buf_left -= (sizeof(*tlv_rxba) + tlv_len);
-		tmp = (u8 *)tlv_rxba + tlv_len + sizeof(*tlv_rxba);
+		tlv_buf_left -= (sizeof(tlv_rxba->header) + tlv_len);
+		tmp = (u8 *)tlv_rxba  + sizeof(tlv_rxba->header) + tlv_len;
 		tlv_rxba = (struct mwifiex_ie_types_rxba_sync *)tmp;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/cfg80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/cfg80211.c
@@ -908,16 +908,20 @@
 	switch (type) {
 	case NL80211_IFTYPE_STATION:
 	case NL80211_IFTYPE_ADHOC:
-		priv->bss_role =  MWIFIEX_BSS_ROLE_STA;
+		priv->bss_role = MWIFIEX_BSS_ROLE_STA;
+		priv->bss_type = MWIFIEX_BSS_TYPE_STA;
 		break;
 	case NL80211_IFTYPE_P2P_CLIENT:
-		priv->bss_role =  MWIFIEX_BSS_ROLE_STA;
+		priv->bss_role = MWIFIEX_BSS_ROLE_STA;
+		priv->bss_type = MWIFIEX_BSS_TYPE_P2P;
 		break;
 	case NL80211_IFTYPE_P2P_GO:
-		priv->bss_role =  MWIFIEX_BSS_ROLE_UAP;
+		priv->bss_role = MWIFIEX_BSS_ROLE_UAP;
+		priv->bss_type = MWIFIEX_BSS_TYPE_P2P;
 		break;
 	case NL80211_IFTYPE_AP:
 		priv->bss_role = MWIFIEX_BSS_ROLE_UAP;
+		priv->bss_type = MWIFIEX_BSS_TYPE_UAP;
 		break;
 	default:
 		mwifiex_dbg(adapter, ERROR,
@@ -926,6 +930,8 @@
 		return -EOPNOTSUPP;
 	}
 
+	priv->bss_num = mwifiex_get_unused_bss_num(adapter, priv->bss_type);
+
 	spin_lock_irqsave(&adapter->main_proc_lock, flags);
 	adapter->main_locked = false;
 	spin_unlock_irqrestore(&adapter->main_proc_lock, flags);
@@ -1229,29 +1235,15 @@
 		break;
 	case NL80211_IFTYPE_P2P_CLIENT:
 	case NL80211_IFTYPE_P2P_GO:
+		if (mwifiex_cfg80211_deinit_p2p(priv))
+			return -EFAULT;
+
 		switch (type) {
-		case NL80211_IFTYPE_STATION:
-			if (mwifiex_cfg80211_deinit_p2p(priv))
-				return -EFAULT;
-			priv->adapter->curr_iface_comb.p2p_intf--;
-			priv->adapter->curr_iface_comb.sta_intf++;
-			dev->ieee80211_ptr->iftype = type;
-			if (mwifiex_deinit_priv_params(priv))
-				return -1;
-			if (mwifiex_init_new_priv_params(priv, dev, type))
-				return -1;
-			if (mwifiex_sta_init_cmd(priv, false, false))
-				return -1;
-			break;
 		case NL80211_IFTYPE_ADHOC:
-			if (mwifiex_cfg80211_deinit_p2p(priv))
-				return -EFAULT;
+		case NL80211_IFTYPE_STATION:
 			return mwifiex_change_vif_to_sta_adhoc(dev, curr_iftype,
 							       type, params);
-			break;
 		case NL80211_IFTYPE_AP:
-			if (mwifiex_cfg80211_deinit_p2p(priv))
-				return -EFAULT;
 			return mwifiex_change_vif_to_ap(dev, curr_iftype, type,
 							params);
 		case NL80211_IFTYPE_UNSPECIFIED:
@@ -1990,6 +1982,8 @@
 
 	mwifiex_set_sys_config_invalid_data(bss_cfg);
 
+	memcpy(bss_cfg->mac_addr, priv->curr_addr, ETH_ALEN);
+
 	if (params->beacon_interval)
 		bss_cfg->beacon_period = params->beacon_interval;
 	if (params->dtim_period)
@@ -3177,13 +3171,11 @@
 		cfg80211_unregister_netdevice(wdev->netdev);
 
 	if (priv->dfs_cac_workqueue) {
-		flush_workqueue(priv->dfs_cac_workqueue);
 		destroy_workqueue(priv->dfs_cac_workqueue);
 		priv->dfs_cac_workqueue = NULL;
 	}
 
 	if (priv->dfs_chan_sw_workqueue) {
-		flush_workqueue(priv->dfs_chan_sw_workqueue);
 		destroy_workqueue(priv->dfs_chan_sw_workqueue);
 		priv->dfs_chan_sw_workqueue = NULL;
 	}
@@ -4336,11 +4328,27 @@
 	if (ISSUPP_ADHOC_ENABLED(adapter->fw_cap_info))
 		wiphy->interface_modes |= BIT(NL80211_IFTYPE_ADHOC);
 
-	wiphy->bands[NL80211_BAND_2GHZ] = &mwifiex_band_2ghz;
-	if (adapter->config_bands & BAND_A)
-		wiphy->bands[NL80211_BAND_5GHZ] = &mwifiex_band_5ghz;
-	else
+	wiphy->bands[NL80211_BAND_2GHZ] = devm_kmemdup(adapter->dev,
+						       &mwifiex_band_2ghz,
+						       sizeof(mwifiex_band_2ghz),
+						       GFP_KERNEL);
+	if (!wiphy->bands[NL80211_BAND_2GHZ]) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	if (adapter->config_bands & BAND_A) {
+		wiphy->bands[NL80211_BAND_5GHZ] = devm_kmemdup(adapter->dev,
+							       &mwifiex_band_5ghz,
+							       sizeof(mwifiex_band_5ghz),
+							       GFP_KERNEL);
+		if (!wiphy->bands[NL80211_BAND_5GHZ]) {
+			ret = -ENOMEM;
+			goto err;
+		}
+	} else {
 		wiphy->bands[NL80211_BAND_5GHZ] = NULL;
+	}
 
 	if (adapter->drcs_enabled && ISSUPP_DRCS_ENABLED(adapter->fw_cap_info))
 		wiphy->iface_combinations = &mwifiex_iface_comb_ap_sta_drcs;
@@ -4433,8 +4441,7 @@
 	if (ret < 0) {
 		mwifiex_dbg(adapter, ERROR,
 			    "%s: wiphy_register failed: %d\n", __func__, ret);
-		wiphy_free(wiphy);
-		return ret;
+		goto err;
 	}
 
 	if (!adapter->regd) {
@@ -4476,4 +4483,9 @@
 
 	adapter->wiphy = wiphy;
 	return ret;
+
+err:
+	wiphy_free(wiphy);
+
+	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/debugfs.c
@@ -265,8 +265,11 @@
 	if (!p)
 		return -ENOMEM;
 
-	if (!priv || !priv->hist_data)
-		return -EFAULT;
+	if (!priv || !priv->hist_data) {
+		ret = -EFAULT;
+		goto free_and_exit;
+	}
+
 	phist_data = priv->hist_data;
 
 	p += sprintf(p, "\n"
@@ -321,6 +324,8 @@
 	ret = simple_read_from_buffer(ubuf, count, ppos, (char *)page,
 				      (unsigned long)p - page);
 
+free_and_exit:
+	free_page(page);
 	return ret;
 }
 
@@ -971,9 +976,6 @@
 	priv->dfs_dev_dir = debugfs_create_dir(priv->netdev->name,
 					       mwifiex_dfs_dir);
 
-	if (!priv->dfs_dev_dir)
-		return;
-
 	MWIFIEX_DFS_ADD_FILE(info);
 	MWIFIEX_DFS_ADD_FILE(debug);
 	MWIFIEX_DFS_ADD_FILE(getlog);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/fw.h
@@ -177,6 +177,7 @@
 #define TLV_TYPE_STA_MAC_ADDR       (PROPRIETARY_TLV_BASE_ID + 32)
 #define TLV_TYPE_BSSID              (PROPRIETARY_TLV_BASE_ID + 35)
 #define TLV_TYPE_CHANNELBANDLIST    (PROPRIETARY_TLV_BASE_ID + 42)
+#define TLV_TYPE_UAP_MAC_ADDRESS    (PROPRIETARY_TLV_BASE_ID + 43)
 #define TLV_TYPE_UAP_BEACON_PERIOD  (PROPRIETARY_TLV_BASE_ID + 44)
 #define TLV_TYPE_UAP_DTIM_PERIOD    (PROPRIETARY_TLV_BASE_ID + 45)
 #define TLV_TYPE_UAP_BCAST_SSID     (PROPRIETARY_TLV_BASE_ID + 48)
@@ -217,6 +218,7 @@
 #define TLV_TYPE_CHANNEL_STATS      (PROPRIETARY_TLV_BASE_ID + 198)
 #define TLV_BTCOEX_WL_AGGR_WINSIZE  (PROPRIETARY_TLV_BASE_ID + 202)
 #define TLV_BTCOEX_WL_SCANTIME      (PROPRIETARY_TLV_BASE_ID + 203)
+#define TLV_TYPE_LED_CONTROL        (PROPRIETARY_TLV_BASE_ID + 205)
 #define TLV_TYPE_BSS_MODE           (PROPRIETARY_TLV_BASE_ID + 206)
 #define TLV_TYPE_RANDOM_MAC         (PROPRIETARY_TLV_BASE_ID + 236)
 #define TLV_TYPE_CHAN_ATTR_CFG      (PROPRIETARY_TLV_BASE_ID + 237)
@@ -364,6 +366,7 @@
 #define HostCmd_CMD_802_11_AD_HOC_JOIN                0x002c
 #define HostCmd_CMD_802_11_AD_HOC_STOP                0x0040
 #define HostCmd_CMD_802_11_MAC_ADDRESS                0x004D
+#define HostCmd_CMD_802_11_LED_CONTROL                0X004E
 #define HostCmd_CMD_802_11D_DOMAIN_INFO               0x005b
 #define HostCmd_CMD_802_11_KEY_MATERIAL               0x005e
 #define HostCmd_CMD_802_11_BG_SCAN_CONFIG             0x006b
@@ -853,7 +856,7 @@
 struct mwifiex_ie_types_wildcard_ssid_params {
 	struct mwifiex_ie_types_header header;
 	u8 max_ssid_length;
-	u8 ssid[1];
+	u8 ssid[];
 } __packed;
 
 #define TSF_DATA_SIZE            8
@@ -1201,6 +1204,16 @@
 	u8 oper_mode;
 } __packed;
 
+struct mwifiex_led_param {
+	__le16 mode;
+	__le16 on;
+} __packed;
+
+struct mwifiex_ie_types_led_param {
+	struct mwifiex_ie_types_header header;
+	struct mwifiex_led_param led_cfg;
+} __packed;
+
 struct host_cmd_ds_802_11_ad_hoc_start {
 	u8 ssid[IEEE80211_MAX_SSID_LEN];
 	u8 bss_mode;
@@ -1324,6 +1337,11 @@
 	} params;
 } __packed;
 
+struct host_cmd_ds_802_11_led_control {
+	__le16 action;
+	__le16 num_led;
+} __packed;
+
 enum SNMP_MIB_INDEX {
 	OP_RATE_SET_I = 1,
 	DTIM_PERIOD_I = 3,
@@ -1597,7 +1615,7 @@
 
 struct host_cmd_ds_802_11_scan_ext {
 	u32   reserved;
-	u8    tlv_buffer[1];
+	u8    tlv_buffer[];
 } __packed;
 
 struct mwifiex_ie_types_bss_mode {
@@ -2379,6 +2397,7 @@
 		struct host_cmd_sdio_sp_rx_aggr_cfg sdio_rx_aggr_cfg;
 		struct host_cmd_ds_multi_chan_policy mc_policy;
 		struct host_cmd_ds_robust_coex coex;
+		struct host_cmd_ds_802_11_led_control led_cfg;
 		struct host_cmd_ds_wakeup_reason hs_wakeup_reason;
 		struct host_cmd_ds_gtk_rekey_params rekey;
 		struct host_cmd_ds_chan_region_cfg reg_cfg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/ioctl.h
@@ -119,6 +119,7 @@
 	u8 qos_info;
 	u8 power_constraint;
 	struct mwifiex_types_wmm_info wmm_info;
+	u8 mac_addr[ETH_ALEN];
 };
 
 enum {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/main.c
@@ -498,13 +498,11 @@
 static void mwifiex_terminate_workqueue(struct mwifiex_adapter *adapter)
 {
 	if (adapter->workqueue) {
-		flush_workqueue(adapter->workqueue);
 		destroy_workqueue(adapter->workqueue);
 		adapter->workqueue = NULL;
 	}
 
 	if (adapter->rx_workqueue) {
-		flush_workqueue(adapter->rx_workqueue);
 		destroy_workqueue(adapter->rx_workqueue);
 		adapter->rx_workqueue = NULL;
 	}
@@ -735,8 +733,10 @@
 static int
 mwifiex_open(struct net_device *dev)
 {
-	netif_carrier_off(dev);
+	struct mwifiex_private *priv = mwifiex_netdev_get_priv(dev);
 
+	netif_carrier_off(dev);
+	mwifiex_set_led(priv->adapter, MWIFIEX_LED_ON);
 	return 0;
 }
 
@@ -767,6 +767,7 @@
 		cfg80211_sched_scan_stopped(priv->wdev.wiphy, 0);
 	}
 
+	mwifiex_set_led(priv->adapter, MWIFIEX_LED_OFF);
 	return 0;
 }
 
@@ -1616,7 +1617,8 @@
 	}
 
 	ret = devm_request_irq(dev, adapter->irq_wakeup,
-			       mwifiex_irq_wakeup_handler, IRQF_TRIGGER_LOW,
+			       mwifiex_irq_wakeup_handler,
+			       IRQF_TRIGGER_LOW | IRQF_NO_AUTOEN,
 			       "wifi_wake", adapter);
 	if (ret) {
 		dev_err(dev, "Failed to request irq_wakeup %d (%d)\n",
@@ -1624,7 +1626,6 @@
 		goto err_exit;
 	}
 
-	disable_irq(adapter->irq_wakeup);
 	if (device_init_wakeup(dev, true)) {
 		dev_err(dev, "fail to init wakeup for mwifiex\n");
 		goto err_exit;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/main.h
@@ -132,6 +132,10 @@
 
 #define PKT_TYPE_MGMT	0xE5
 
+#define MWIFIEX_LED_ON		1
+#define MWIFIEX_LED_OFF		0
+#define MWIFIEX_LED_MAX		3
+
 /*
  * Do not check for data_received for USB, as data_received
  * is handled in mwifiex_usb_recv for USB
@@ -700,6 +704,7 @@
 	struct mwifiex_user_scan_chan hidden_chan[MWIFIEX_USER_SCAN_CHAN_MAX];
 	u8 assoc_resp_ht_param;
 	bool ht_param_present;
+	bool is_edge_gateway;
 };
 
 
@@ -1054,6 +1059,8 @@
 	void *devdump_data;
 	int devdump_len;
 	struct timer_list devdump_timer;
+
+	bool ignore_btcoex_events;
 };
 
 void mwifiex_process_tx_queue(struct mwifiex_adapter *adapter);
@@ -1308,6 +1315,9 @@
 
 	for (i = 0; i < adapter->priv_num; i++) {
 		if (adapter->priv[i]) {
+			if (adapter->priv[i]->bss_mode == NL80211_IFTYPE_UNSPECIFIED)
+				continue;
+
 			if ((adapter->priv[i]->bss_num == bss_num) &&
 			    (adapter->priv[i]->bss_type == bss_type))
 				break;
@@ -1495,6 +1505,7 @@
 				struct cmd_ctrl_node *cmd_queued);
 int mwifiex_bss_start(struct mwifiex_private *priv, struct cfg80211_bss *bss,
 		      struct cfg80211_ssid *req_ssid);
+int mwifiex_set_led(struct mwifiex_adapter *adapter, int on);
 int mwifiex_cancel_hs(struct mwifiex_private *priv, int cmd_type);
 int mwifiex_enable_hs(struct mwifiex_adapter *adapter);
 int mwifiex_disable_auto_ds(struct mwifiex_private *priv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/pcie.c
@@ -17,6 +17,7 @@
  * this warranty disclaimer.
  */
 
+#include <linux/iopoll.h>
 #include <linux/firmware.h>
 
 #include "decl.h"
@@ -183,7 +184,7 @@
 	.can_ext_scan = true,
 };
 
-static const struct of_device_id mwifiex_pcie_of_match_table[] = {
+static const struct of_device_id mwifiex_pcie_of_match_table[] __maybe_unused = {
 	{ .compatible = "pci11ab,2b42" },
 	{ .compatible = "pci1b4b,2b42" },
 	{ }
@@ -200,6 +201,8 @@
 }
 
 static void mwifiex_pcie_work(struct work_struct *work);
+static int mwifiex_pcie_delete_rxbd_ring(struct mwifiex_adapter *adapter);
+static int mwifiex_pcie_delete_evtbd_ring(struct mwifiex_adapter *adapter);
 
 static int
 mwifiex_map_pci_memory(struct mwifiex_adapter *adapter, struct sk_buff *skb,
@@ -379,6 +382,8 @@
 					const struct pci_device_id *ent)
 {
 	struct pcie_service_card *card;
+	struct mwifiex_private *priv;
+	struct pci_dev *pdev_host;
 	int ret;
 
 	pr_debug("info: vendor=0x%4.04X device=0x%4.04X rev=%d\n",
@@ -420,6 +425,14 @@
 		return -1;
 	}
 
+	priv = mwifiex_get_priv(card->adapter, MWIFIEX_BSS_ROLE_STA);
+	pdev_host = pci_get_subsys(PCI_ANY_ID, PCI_ANY_ID, 0x1028, 0x0720, NULL);
+	if (!pdev_host)
+		pdev_host = pci_get_subsys(PCI_ANY_ID, PCI_ANY_ID, 0x1028, 0x0733, NULL);
+	if (pdev_host) {
+		priv->is_edge_gateway = true;
+		pci_dev_put(pdev_host);
+	}
 	return 0;
 }
 
@@ -647,11 +660,15 @@
 			    "max count reached while accessing sleep cookie\n");
 }
 
+#define N_WAKEUP_TRIES_SHORT_INTERVAL 15
+#define N_WAKEUP_TRIES_LONG_INTERVAL 35
+
 /* This function wakes up the card by reading fw_status register. */
 static int mwifiex_pm_wakeup_card(struct mwifiex_adapter *adapter)
 {
 	struct pcie_service_card *card = adapter->card;
 	const struct mwifiex_pcie_card_reg *reg = card->pcie.reg;
+	int retval;
 
 	mwifiex_dbg(adapter, EVENT,
 		    "event: Wakeup device...\n");
@@ -659,11 +676,24 @@
 	if (reg->sleep_cookie)
 		mwifiex_pcie_dev_wakeup_delay(adapter);
 
-	/* Accessing fw_status register will wakeup device */
-	if (mwifiex_write_reg(adapter, reg->fw_status, FIRMWARE_READY_PCIE)) {
-		mwifiex_dbg(adapter, ERROR,
-			    "Writing fw_status register failed\n");
-		return -1;
+	/* The 88W8897 PCIe+USB firmware (latest version 15.68.19.p21) sometimes
+	 * appears to ignore or miss our wakeup request, so we continue trying
+	 * until we receive an interrupt from the card.
+	 */
+	if (read_poll_timeout(mwifiex_write_reg, retval,
+			      READ_ONCE(adapter->int_status) != 0,
+			      500, 500 * N_WAKEUP_TRIES_SHORT_INTERVAL,
+			      false,
+			      adapter, reg->fw_status, FIRMWARE_READY_PCIE)) {
+		if (read_poll_timeout(mwifiex_write_reg, retval,
+				      READ_ONCE(adapter->int_status) != 0,
+				      10000, 10000 * N_WAKEUP_TRIES_LONG_INTERVAL,
+				      false,
+				      adapter, reg->fw_status, FIRMWARE_READY_PCIE)) {
+			mwifiex_dbg(adapter, ERROR,
+				    "Firmware didn't wake up\n");
+			return -EIO;
+		}
 	}
 
 	if (reg->sleep_cookie) {
@@ -786,14 +816,15 @@
 		if (!skb) {
 			mwifiex_dbg(adapter, ERROR,
 				    "Unable to allocate skb for RX ring.\n");
-			kfree(card->rxbd_ring_vbase);
 			return -ENOMEM;
 		}
 
 		if (mwifiex_map_pci_memory(adapter, skb,
 					   MWIFIEX_RX_DATA_BUF_SIZE,
-					   DMA_FROM_DEVICE))
-			return -1;
+					   DMA_FROM_DEVICE)) {
+			kfree_skb(skb);
+			return -ENOMEM;
+		}
 
 		buf_pa = MWIFIEX_SKB_DMA_ADDR(skb);
 
@@ -843,7 +874,6 @@
 		if (!skb) {
 			mwifiex_dbg(adapter, ERROR,
 				    "Unable to allocate skb for EVENT buf.\n");
-			kfree(card->evtbd_ring_vbase);
 			return -ENOMEM;
 		}
 		skb_put(skb, MAX_EVENT_SIZE);
@@ -851,8 +881,7 @@
 		if (mwifiex_map_pci_memory(adapter, skb, MAX_EVENT_SIZE,
 					   DMA_FROM_DEVICE)) {
 			kfree_skb(skb);
-			kfree(card->evtbd_ring_vbase);
-			return -1;
+			return -ENOMEM;
 		}
 
 		buf_pa = MWIFIEX_SKB_DMA_ADDR(skb);
@@ -1052,6 +1081,7 @@
  */
 static int mwifiex_pcie_create_rxbd_ring(struct mwifiex_adapter *adapter)
 {
+	int ret;
 	struct pcie_service_card *card = adapter->card;
 	const struct mwifiex_pcie_card_reg *reg = card->pcie.reg;
 
@@ -1090,7 +1120,10 @@
 		    (u32)((u64)card->rxbd_ring_pbase >> 32),
 		    card->rxbd_ring_size);
 
-	return mwifiex_init_rxq_ring(adapter);
+	ret = mwifiex_init_rxq_ring(adapter);
+	if (ret)
+		mwifiex_pcie_delete_rxbd_ring(adapter);
+	return ret;
 }
 
 /*
@@ -1121,6 +1154,7 @@
  */
 static int mwifiex_pcie_create_evtbd_ring(struct mwifiex_adapter *adapter)
 {
+	int ret;
 	struct pcie_service_card *card = adapter->card;
 	const struct mwifiex_pcie_card_reg *reg = card->pcie.reg;
 
@@ -1155,7 +1189,10 @@
 		    (u32)((u64)card->evtbd_ring_pbase >> 32),
 		    card->evtbd_ring_size);
 
-	return mwifiex_pcie_init_evt_ring(adapter);
+	ret = mwifiex_pcie_init_evt_ring(adapter);
+	if (ret)
+		mwifiex_pcie_delete_evtbd_ring(adapter);
+	return ret;
 }
 
 /*
@@ -1490,6 +1527,14 @@
 			ret = -1;
 			goto done_unmap;
 		}
+
+		/* The firmware (latest version 15.68.19.p21) of the 88W8897 PCIe+USB card
+		 * seems to crash randomly after setting the TX ring write pointer when
+		 * ASPM powersaving is enabled. A workaround seems to be keeping the bus
+		 * busy by reading a random register afterwards.
+		 */
+		mwifiex_read_reg(adapter, PCI_VENDOR_ID, &rx_val);
+
 		if ((mwifiex_pcie_txbd_not_full(card)) &&
 		    tx_param->next_pkt_len) {
 			/* have more packets and TxBD still can hold more */
@@ -3126,6 +3171,9 @@
 	if (ret)
 		goto err_alloc_buffers;
 
+	if (pdev->device == PCIE_DEVICE_ID_MARVELL_88W8897)
+		adapter->ignore_btcoex_events = true;
+
 	return 0;
 
 err_alloc_buffers:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/scan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/scan.c
@@ -2199,9 +2199,9 @@
 
 	if (nd_config) {
 		adapter->nd_info =
-			kzalloc(sizeof(struct cfg80211_wowlan_nd_match) +
-				sizeof(struct cfg80211_wowlan_nd_match *) *
-				scan_rsp->number_of_sets, GFP_ATOMIC);
+			kzalloc(struct_size(adapter->nd_info, matches,
+					    scan_rsp->number_of_sets),
+				GFP_ATOMIC);
 
 		if (adapter->nd_info)
 			adapter->nd_info->n_matches = scan_rsp->number_of_sets;
@@ -2560,8 +2560,7 @@
 	ext_scan_resp = &resp->params.ext_scan;
 
 	tlv = (void *)ext_scan_resp->tlv_buffer;
-	buf_left = le16_to_cpu(resp->size) - (sizeof(*ext_scan_resp) + S_DS_GEN
-					      - 1);
+	buf_left = le16_to_cpu(resp->size) - (sizeof(*ext_scan_resp) + S_DS_GEN);
 
 	while (buf_left >= sizeof(struct mwifiex_ie_types_header)) {
 		type = le16_to_cpu(tlv->type);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/sdio.c
@@ -484,7 +484,8 @@
 	{"EXTLAST", NULL, 0, 0xFE},
 };
 
-static const struct of_device_id mwifiex_sdio_of_match_table[] = {
+static const struct of_device_id mwifiex_sdio_of_match_table[] __maybe_unused = {
+	{ .compatible = "marvell,sd8787" },
 	{ .compatible = "marvell,sd8897" },
 	{ .compatible = "marvell,sd8997" },
 	{ }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/sta_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/sta_cmd.c
@@ -424,6 +424,31 @@
 	return 0;
 }
 
+static int mwifiex_cmd_802_11_led_cfg(struct mwifiex_private *priv,
+				      struct host_cmd_ds_command *cmd,
+				      u16 cmd_action,
+				      struct mwifiex_led_param *ledcfg_param)
+{
+	struct host_cmd_ds_802_11_led_control *led_cfg = &cmd->params.led_cfg;
+	struct mwifiex_ie_types_led_param *led_tlv;
+	u8 *pos;
+
+	cmd->command = cpu_to_le16(HostCmd_CMD_802_11_LED_CONTROL);
+	cmd->size = cpu_to_le16(S_DS_GEN);
+	le16_add_cpu(&cmd->size, sizeof(struct host_cmd_ds_802_11_led_control));
+
+	led_cfg->action = cpu_to_le16(cmd_action);
+	led_cfg->num_led = cpu_to_le16(MWIFIEX_LED_MAX);
+
+	pos = (u8 *)led_cfg + sizeof(struct host_cmd_ds_802_11_led_control);
+	led_tlv = (void *)pos;
+	led_tlv->header.type = cpu_to_le16(TLV_TYPE_LED_CONTROL);
+	led_tlv->header.len = cpu_to_le16(sizeof(struct mwifiex_led_param));
+	memcpy(&led_tlv->led_cfg, ledcfg_param, sizeof(struct mwifiex_led_param));
+	le16_add_cpu(&cmd->size, sizeof(struct mwifiex_ie_types_led_param));
+	return 0;
+}
+
 /*
  * This function prepares command to set/get MAC address.
  *
@@ -1993,6 +2018,10 @@
 		ret = mwifiex_cmd_802_11_hs_cfg(priv, cmd_ptr, cmd_action,
 				(struct mwifiex_hs_config_param *) data_buf);
 		break;
+	case HostCmd_CMD_802_11_LED_CONTROL:
+		ret = mwifiex_cmd_802_11_led_cfg(priv, cmd_ptr, cmd_action,
+						 data_buf);
+		break;
 	case HostCmd_CMD_802_11_SCAN:
 		ret = mwifiex_cmd_802_11_scan(cmd_ptr, data_buf);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/sta_cmdresp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/sta_cmdresp.c
@@ -1410,6 +1410,8 @@
 	case HostCmd_CMD_ROBUST_COEX:
 		ret = mwifiex_ret_robust_coex(priv, resp, data_buf);
 		break;
+	case HostCmd_CMD_802_11_LED_CONTROL:
+		break;
 	case HostCmd_CMD_GTK_REKEY_OFFLOAD_CFG:
 		break;
 	case HostCmd_CMD_CHAN_REGION_CFG:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/sta_event.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/sta_event.c
@@ -365,10 +365,12 @@
 		sta_ptr = mwifiex_get_sta_entry(priv, tp->peermac);
 		if (sta_ptr && sta_ptr->tx_pause != tp->tx_pause) {
 			sta_ptr->tx_pause = tp->tx_pause;
+			spin_unlock_bh(&priv->sta_list_spinlock);
 			mwifiex_update_ralist_tx_pause(priv, tp->peermac,
 						       tp->tx_pause);
+		} else {
+			spin_unlock_bh(&priv->sta_list_spinlock);
 		}
-		spin_unlock_bh(&priv->sta_list_spinlock);
 	}
 }
 
@@ -400,11 +402,13 @@
 			sta_ptr = mwifiex_get_sta_entry(priv, tp->peermac);
 			if (sta_ptr && sta_ptr->tx_pause != tp->tx_pause) {
 				sta_ptr->tx_pause = tp->tx_pause;
+				spin_unlock_bh(&priv->sta_list_spinlock);
 				mwifiex_update_ralist_tx_pause(priv,
 							       tp->peermac,
 							       tp->tx_pause);
+			} else {
+				spin_unlock_bh(&priv->sta_list_spinlock);
 			}
-			spin_unlock_bh(&priv->sta_list_spinlock);
 		}
 	}
 }
@@ -1058,6 +1062,9 @@
 		break;
 	case EVENT_BT_COEX_WLAN_PARA_CHANGE:
 		dev_dbg(adapter->dev, "EVENT: BT coex wlan param update\n");
+		if (adapter->ignore_btcoex_events)
+			break;
+
 		mwifiex_bt_coex_wlan_param_update_event(priv,
 							adapter->event_skb);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/sta_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/sta_ioctl.c
@@ -570,6 +570,24 @@
 }
 EXPORT_SYMBOL_GPL(mwifiex_enable_hs);
 
+int mwifiex_set_led(struct mwifiex_adapter *adapter, int on)
+{
+	struct mwifiex_private *priv;
+	struct mwifiex_led_param ledcfg;
+
+	priv = mwifiex_get_priv(adapter, MWIFIEX_BSS_ROLE_STA);
+	if (!priv->is_edge_gateway)
+		return -ENODEV;
+
+	memset(&ledcfg, 0, sizeof(struct mwifiex_led_param));
+	ledcfg.on = cpu_to_le16(on);
+
+	return mwifiex_send_cmd(priv,
+				HostCmd_CMD_802_11_LED_CONTROL,
+				HostCmd_ACT_GEN_SET, 0,
+				&ledcfg, true);
+}
+
 /*
  * IOCTL request handler to get BSS information.
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/sta_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/sta_rx.c
@@ -98,12 +98,23 @@
 	rx_pkt_len = le16_to_cpu(local_rx_pd->rx_pkt_length);
 	rx_pkt_hdr = (void *)local_rx_pd + rx_pkt_off;
 
-	if ((!memcmp(&rx_pkt_hdr->rfc1042_hdr, bridge_tunnel_header,
-		     sizeof(bridge_tunnel_header))) ||
-	    (!memcmp(&rx_pkt_hdr->rfc1042_hdr, rfc1042_header,
-		     sizeof(rfc1042_header)) &&
-	     ntohs(rx_pkt_hdr->rfc1042_hdr.snap_type) != ETH_P_AARP &&
-	     ntohs(rx_pkt_hdr->rfc1042_hdr.snap_type) != ETH_P_IPX)) {
+	if (sizeof(rx_pkt_hdr->eth803_hdr) + sizeof(rfc1042_header) +
+	    rx_pkt_off > skb->len) {
+		mwifiex_dbg(priv->adapter, ERROR,
+			    "wrong rx packet offset: len=%d, rx_pkt_off=%d\n",
+			    skb->len, rx_pkt_off);
+		priv->stats.rx_dropped++;
+		dev_kfree_skb_any(skb);
+		return -1;
+	}
+
+	if (sizeof(*rx_pkt_hdr) + rx_pkt_off <= skb->len &&
+	    ((!memcmp(&rx_pkt_hdr->rfc1042_hdr, bridge_tunnel_header,
+		      sizeof(bridge_tunnel_header))) ||
+	     (!memcmp(&rx_pkt_hdr->rfc1042_hdr, rfc1042_header,
+		      sizeof(rfc1042_header)) &&
+	      ntohs(rx_pkt_hdr->rfc1042_hdr.snap_type) != ETH_P_AARP &&
+	      ntohs(rx_pkt_hdr->rfc1042_hdr.snap_type) != ETH_P_IPX))) {
 		/*
 		 *  Replace the 803 header and rfc1042 header (llc/snap) with an
 		 *    EthernetII header, keep the src/dst and snap_type
@@ -206,7 +217,8 @@
 
 	rx_pkt_hdr = (void *)local_rx_pd + rx_pkt_offset;
 
-	if ((rx_pkt_offset + rx_pkt_length) > (u16) skb->len) {
+	if ((rx_pkt_offset + rx_pkt_length) > skb->len ||
+	    sizeof(rx_pkt_hdr->eth803_hdr) + rx_pkt_offset > skb->len) {
 		mwifiex_dbg(adapter, ERROR,
 			    "wrong rx packet: len=%d, rx_pkt_offset=%d, rx_pkt_length=%d\n",
 			    skb->len, rx_pkt_offset, rx_pkt_length);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/tdls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/tdls.c
@@ -735,6 +735,7 @@
 	int ret;
 	u16 capab;
 	struct ieee80211_ht_cap *ht_cap;
+	unsigned int extra;
 	u8 radio, *pos;
 
 	capab = priv->curr_bss_params.bss_descriptor.cap_info_bitmap;
@@ -753,7 +754,10 @@
 
 	switch (action_code) {
 	case WLAN_PUB_ACTION_TDLS_DISCOVER_RES:
-		skb_put(skb, sizeof(mgmt->u.action.u.tdls_discover_resp) + 1);
+		/* See the layout of 'struct ieee80211_mgmt'. */
+		extra = sizeof(mgmt->u.action.u.tdls_discover_resp) +
+			sizeof(mgmt->u.action.category);
+		skb_put(skb, extra);
 		mgmt->u.action.category = WLAN_CATEGORY_PUBLIC;
 		mgmt->u.action.u.tdls_discover_resp.action_code =
 					      WLAN_PUB_ACTION_TDLS_DISCOVER_RES;
@@ -762,8 +766,7 @@
 		mgmt->u.action.u.tdls_discover_resp.capability =
 							     cpu_to_le16(capab);
 		/* move back for addr4 */
-		memmove(pos + ETH_ALEN, &mgmt->u.action.category,
-			sizeof(mgmt->u.action.u.tdls_discover_resp));
+		memmove(pos + ETH_ALEN, &mgmt->u.action, extra);
 		/* init address 4 */
 		eth_broadcast_addr(pos);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/uap_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/uap_cmd.c
@@ -480,6 +480,7 @@
 static int
 mwifiex_uap_bss_param_prepare(u8 *tlv, void *cmd_buf, u16 *param_size)
 {
+	struct host_cmd_tlv_mac_addr *mac_tlv;
 	struct host_cmd_tlv_dtim_period *dtim_period;
 	struct host_cmd_tlv_beacon_period *beacon_period;
 	struct host_cmd_tlv_ssid *ssid;
@@ -499,6 +500,13 @@
 	int i;
 	u16 cmd_size = *param_size;
 
+	mac_tlv = (struct host_cmd_tlv_mac_addr *)tlv;
+	mac_tlv->header.type = cpu_to_le16(TLV_TYPE_UAP_MAC_ADDRESS);
+	mac_tlv->header.len = cpu_to_le16(ETH_ALEN);
+	memcpy(mac_tlv->mac_addr, bss_cfg->mac_addr, ETH_ALEN);
+	cmd_size += sizeof(struct host_cmd_tlv_mac_addr);
+	tlv += sizeof(struct host_cmd_tlv_mac_addr);
+
 	if (bss_cfg->ssid.ssid_len) {
 		ssid = (struct host_cmd_tlv_ssid *)tlv;
 		ssid->header.type = cpu_to_le16(TLV_TYPE_UAP_SSID);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/uap_txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/uap_txrx.c
@@ -115,6 +115,16 @@
 		return;
 	}
 
+	if (sizeof(*rx_pkt_hdr) +
+	    le16_to_cpu(uap_rx_pd->rx_pkt_offset) > skb->len) {
+		mwifiex_dbg(adapter, ERROR,
+			    "wrong rx packet offset: len=%d,rx_pkt_offset=%d\n",
+			    skb->len, le16_to_cpu(uap_rx_pd->rx_pkt_offset));
+		priv->stats.rx_dropped++;
+		dev_kfree_skb_any(skb);
+		return;
+	}
+
 	if ((!memcmp(&rx_pkt_hdr->rfc1042_hdr, bridge_tunnel_header,
 		     sizeof(bridge_tunnel_header))) ||
 	    (!memcmp(&rx_pkt_hdr->rfc1042_hdr, rfc1042_header,
@@ -255,7 +265,15 @@
 
 	if (is_multicast_ether_addr(ra)) {
 		skb_uap = skb_copy(skb, GFP_ATOMIC);
-		mwifiex_uap_queue_bridged_pkt(priv, skb_uap);
+		if (likely(skb_uap)) {
+			mwifiex_uap_queue_bridged_pkt(priv, skb_uap);
+		} else {
+			mwifiex_dbg(adapter, ERROR,
+				    "failed to copy skb for uAP\n");
+			priv->stats.rx_dropped++;
+			dev_kfree_skb_any(skb);
+			return -1;
+		}
 	} else {
 		if (mwifiex_get_sta_entry(priv, ra)) {
 			/* Requeue Intra-BSS packet */
@@ -379,6 +397,16 @@
 	rx_pkt_type = le16_to_cpu(uap_rx_pd->rx_pkt_type);
 	rx_pkt_hdr = (void *)uap_rx_pd + le16_to_cpu(uap_rx_pd->rx_pkt_offset);
 
+	if (le16_to_cpu(uap_rx_pd->rx_pkt_offset) +
+	    sizeof(rx_pkt_hdr->eth803_hdr) > skb->len) {
+		mwifiex_dbg(adapter, ERROR,
+			    "wrong rx packet for struct ethhdr: len=%d, offset=%d\n",
+			    skb->len, le16_to_cpu(uap_rx_pd->rx_pkt_offset));
+		priv->stats.rx_dropped++;
+		dev_kfree_skb_any(skb);
+		return 0;
+	}
+
 	ether_addr_copy(ta, rx_pkt_hdr->eth803_hdr.h_source);
 
 	if ((le16_to_cpu(uap_rx_pd->rx_pkt_offset) +
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/usb.c
@@ -130,7 +130,8 @@
 		default:
 			mwifiex_dbg(adapter, ERROR,
 				    "unknown recv_type %#x\n", recv_type);
-			return -1;
+			ret = -1;
+			goto exit_restore_skb;
 		}
 		break;
 	case MWIFIEX_USB_EP_DATA:
@@ -505,6 +506,22 @@
 		}
 	}
 
+	switch (card->usb_boot_state) {
+	case USB8XXX_FW_DNLD:
+		/* Reject broken descriptors. */
+		if (!card->rx_cmd_ep || !card->tx_cmd_ep)
+			return -ENODEV;
+		if (card->bulk_out_maxpktsize == 0)
+			return -ENODEV;
+		break;
+	case USB8XXX_FW_READY:
+		/* Assume the driver can handle missing endpoints for now. */
+		break;
+	default:
+		WARN_ON(1);
+		return -ENODEV;
+	}
+
 	usb_set_intfdata(intf, card);
 
 	ret = mwifiex_add_card(card, &card->fw_done, &usb_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwifiex/util.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwifiex/util.c
@@ -405,11 +405,15 @@
 	}
 
 	rx_pd = (struct rxpd *)skb->data;
+	pkt_len = le16_to_cpu(rx_pd->rx_pkt_length);
+	if (pkt_len < sizeof(struct ieee80211_hdr) + sizeof(pkt_len)) {
+		mwifiex_dbg(priv->adapter, ERROR, "invalid rx_pkt_length");
+		return -1;
+	}
 
 	skb_pull(skb, le16_to_cpu(rx_pd->rx_pkt_offset));
 	skb_pull(skb, sizeof(pkt_len));
-
-	pkt_len = le16_to_cpu(rx_pd->rx_pkt_length);
+	pkt_len -= sizeof(pkt_len);
 
 	ieee_hdr = (void *)skb->data;
 	if (ieee80211_is_mgmt(ieee_hdr->frame_control)) {
@@ -422,7 +426,7 @@
 		skb->data + sizeof(struct ieee80211_hdr),
 		pkt_len - sizeof(struct ieee80211_hdr));
 
-	pkt_len -= ETH_ALEN + sizeof(pkt_len);
+	pkt_len -= ETH_ALEN;
 	rx_pd->rx_pkt_length = cpu_to_le16(pkt_len);
 
 	cfg80211_rx_mgmt(&priv->wdev, priv->roc_cfg.chan.center_freq,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/marvell/mwl8k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/marvell/mwl8k.c
@@ -2718,7 +2718,7 @@
 		cmd->action |= cpu_to_le16(MWL8K_ENABLE_RX_MULTICAST);
 		cmd->numaddr = cpu_to_le16(mc_count);
 		netdev_hw_addr_list_for_each(ha, mc_list) {
-			memcpy(cmd->addr[i], ha->addr, ETH_ALEN);
+			memcpy(cmd->addr[i++], ha->addr, ETH_ALEN);
 		}
 	}
 
@@ -5800,8 +5800,8 @@
 fail:
 	priv->fw_state = FW_STATE_ERROR;
 	complete(&priv->firmware_loading_complete);
-	device_release_driver(&priv->pdev->dev);
 	mwl8k_release_firmware(priv);
+	device_release_driver(&priv->pdev->dev);
 }
 
 #define MAX_RESTART_ATTEMPTS 1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/agg-rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/agg-rx.c
@@ -162,8 +162,9 @@
 	if (!sta)
 		return;
 
-	if (!status->aggr && !(status->flag & RX_FLAG_8023)) {
-		mt76_rx_aggr_check_ctl(skb, frames);
+	if (!status->aggr) {
+		if (!(status->flag & RX_FLAG_8023))
+			mt76_rx_aggr_check_ctl(skb, frames);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/debugfs.c
@@ -116,8 +116,11 @@
 	return 0;
 }
 
-struct dentry *mt76_register_debugfs(struct mt76_dev *dev)
+struct dentry *
+mt76_register_debugfs_fops(struct mt76_dev *dev,
+			   const struct file_operations *ops)
 {
+	const struct file_operations *fops = ops ? ops : &fops_regval;
 	struct dentry *dir;
 
 	dir = debugfs_create_dir("mt76", dev->hw->wiphy->debugfsdir);
@@ -126,8 +129,7 @@
 
 	debugfs_create_u8("led_pin", 0600, dir, &dev->led_pin);
 	debugfs_create_u32("regidx", 0600, dir, &dev->debugfs_reg);
-	debugfs_create_file_unsafe("regval", 0600, dir, dev,
-				   &fops_regval);
+	debugfs_create_file_unsafe("regval", 0600, dir, dev, fops);
 	debugfs_create_file_unsafe("napi_threaded", 0600, dir, dev,
 				   &fops_napi_threaded);
 	debugfs_create_blob("eeprom", 0400, dir, &dev->eeprom);
@@ -140,4 +142,4 @@
 
 	return dir;
 }
-EXPORT_SYMBOL_GPL(mt76_register_debugfs);
+EXPORT_SYMBOL_GPL(mt76_register_debugfs_fops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/dma.c
@@ -16,11 +16,11 @@
 	int size;
 
 	size = L1_CACHE_ALIGN(dev->drv->txwi_size + sizeof(*t));
-	txwi = devm_kzalloc(dev->dev, size, GFP_ATOMIC);
+	txwi = kzalloc(size, GFP_ATOMIC);
 	if (!txwi)
 		return NULL;
 
-	addr = dma_map_single(dev->dev, txwi, dev->drv->txwi_size,
+	addr = dma_map_single(dev->dma_dev, txwi, dev->drv->txwi_size,
 			      DMA_TO_DEVICE);
 	t = (struct mt76_txwi_cache *)(txwi + dev->drv->txwi_size);
 	t->dma_addr = addr;
@@ -73,9 +73,11 @@
 	struct mt76_txwi_cache *t;
 
 	local_bh_disable();
-	while ((t = __mt76_get_txwi(dev)) != NULL)
-		dma_unmap_single(dev->dev, t->dma_addr, dev->drv->txwi_size,
+	while ((t = __mt76_get_txwi(dev)) != NULL) {
+		dma_unmap_single(dev->dma_dev, t->dma_addr, dev->drv->txwi_size,
 				 DMA_TO_DEVICE);
+		kfree(mt76_get_txwi_ptr(dev, t));
+	}
 	local_bh_enable();
 }
 
@@ -121,7 +123,7 @@
 	q->hw_idx = idx;
 
 	size = q->ndesc * sizeof(struct mt76_desc);
-	q->desc = dmam_alloc_coherent(dev->dev, size, &q->desc_dma, GFP_KERNEL);
+	q->desc = dmam_alloc_coherent(dev->dma_dev, size, &q->desc_dma, GFP_KERNEL);
 	if (!q->desc)
 		return -ENOMEM;
 
@@ -203,11 +205,11 @@
 	struct mt76_queue_entry *e = &q->entry[idx];
 
 	if (!e->skip_buf0)
-		dma_unmap_single(dev->dev, e->dma_addr[0], e->dma_len[0],
+		dma_unmap_single(dev->dma_dev, e->dma_addr[0], e->dma_len[0],
 				 DMA_TO_DEVICE);
 
 	if (!e->skip_buf1)
-		dma_unmap_single(dev->dev, e->dma_addr[1], e->dma_len[1],
+		dma_unmap_single(dev->dma_dev, e->dma_addr[1], e->dma_len[1],
 				 DMA_TO_DEVICE);
 
 	if (e->txwi == DMA_DUMMY_DATA)
@@ -288,7 +290,7 @@
 	if (info)
 		*info = le32_to_cpu(desc->info);
 
-	dma_unmap_single(dev->dev, buf_addr, buf_len, DMA_FROM_DEVICE);
+	dma_unmap_single(dev->dma_dev, buf_addr, buf_len, DMA_FROM_DEVICE);
 	e->buf = NULL;
 
 	return buf;
@@ -325,9 +327,9 @@
 	if (q->queued + 1 >= q->ndesc - 1)
 		goto error;
 
-	addr = dma_map_single(dev->dev, skb->data, skb->len,
+	addr = dma_map_single(dev->dma_dev, skb->data, skb->len,
 			      DMA_TO_DEVICE);
-	if (unlikely(dma_mapping_error(dev->dev, addr)))
+	if (unlikely(dma_mapping_error(dev->dma_dev, addr)))
 		goto error;
 
 	buf.addr = addr;
@@ -347,8 +349,8 @@
 
 static int
 mt76_dma_tx_queue_skb(struct mt76_dev *dev, struct mt76_queue *q,
-		      struct sk_buff *skb, struct mt76_wcid *wcid,
-		      struct ieee80211_sta *sta)
+		      enum mt76_txq_id qid, struct sk_buff *skb,
+		      struct mt76_wcid *wcid, struct ieee80211_sta *sta)
 {
 	struct ieee80211_tx_status status = {
 		.sta = sta,
@@ -374,8 +376,8 @@
 		mt76_insert_hdr_pad(skb);
 
 	len = skb_headlen(skb);
-	addr = dma_map_single(dev->dev, skb->data, len, DMA_TO_DEVICE);
-	if (unlikely(dma_mapping_error(dev->dev, addr)))
+	addr = dma_map_single(dev->dma_dev, skb->data, len, DMA_TO_DEVICE);
+	if (unlikely(dma_mapping_error(dev->dma_dev, addr)))
 		goto free;
 
 	tx_info.buf[n].addr = t->dma_addr;
@@ -387,9 +389,9 @@
 		if (n == ARRAY_SIZE(tx_info.buf))
 			goto unmap;
 
-		addr = dma_map_single(dev->dev, iter->data, iter->len,
+		addr = dma_map_single(dev->dma_dev, iter->data, iter->len,
 				      DMA_TO_DEVICE);
-		if (unlikely(dma_mapping_error(dev->dev, addr)))
+		if (unlikely(dma_mapping_error(dev->dma_dev, addr)))
 			goto unmap;
 
 		tx_info.buf[n].addr = addr;
@@ -402,10 +404,10 @@
 		goto unmap;
 	}
 
-	dma_sync_single_for_cpu(dev->dev, t->dma_addr, dev->drv->txwi_size,
+	dma_sync_single_for_cpu(dev->dma_dev, t->dma_addr, dev->drv->txwi_size,
 				DMA_TO_DEVICE);
-	ret = dev->drv->tx_prepare_skb(dev, txwi, q->qid, wcid, sta, &tx_info);
-	dma_sync_single_for_device(dev->dev, t->dma_addr, dev->drv->txwi_size,
+	ret = dev->drv->tx_prepare_skb(dev, txwi, qid, wcid, sta, &tx_info);
+	dma_sync_single_for_device(dev->dma_dev, t->dma_addr, dev->drv->txwi_size,
 				   DMA_TO_DEVICE);
 	if (ret < 0)
 		goto unmap;
@@ -415,7 +417,7 @@
 
 unmap:
 	for (n--; n > 0; n--)
-		dma_unmap_single(dev->dev, tx_info.buf[n].addr,
+		dma_unmap_single(dev->dma_dev, tx_info.buf[n].addr,
 				 tx_info.buf[n].len, DMA_TO_DEVICE);
 
 free:
@@ -434,7 +436,9 @@
 free_skb:
 	status.skb = tx_info.skb;
 	hw = mt76_tx_status_get_hw(dev, tx_info.skb);
+	spin_lock_bh(&dev->rx_lock);
 	ieee80211_tx_status_ext(hw, &status);
+	spin_unlock_bh(&dev->rx_lock);
 
 	return ret;
 }
@@ -457,14 +461,15 @@
 		if (!buf)
 			break;
 
-		addr = dma_map_single(dev->dev, buf, len, DMA_FROM_DEVICE);
-		if (unlikely(dma_mapping_error(dev->dev, addr))) {
+		addr = dma_map_single(dev->dma_dev, buf, len, DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(dev->dma_dev, addr))) {
 			skb_free_frag(buf);
 			break;
 		}
 
 		qbuf.addr = addr + offset;
 		qbuf.len = len - offset;
+		qbuf.skip_unmap = false;
 		mt76_dma_add_buf(dev, q, &qbuf, 1, 0, buf, NULL);
 		frames++;
 	}
@@ -485,6 +490,7 @@
 	bool more;
 
 	spin_lock_bh(&q->lock);
+
 	do {
 		buf = mt76_dma_dequeue(dev, q, true, NULL, NULL, &more);
 		if (!buf)
@@ -492,6 +498,12 @@
 
 		skb_free_frag(buf);
 	} while (1);
+
+	if (q->rx_head) {
+		dev_kfree_skb(q->rx_head);
+		q->rx_head = NULL;
+	}
+
 	spin_unlock_bh(&q->lock);
 
 	if (!q->rx_page.va)
@@ -514,12 +526,6 @@
 	mt76_dma_rx_cleanup(dev, q);
 	mt76_dma_sync_idx(dev, q);
 	mt76_dma_rx_fill(dev, q);
-
-	if (!q->rx_head)
-		return;
-
-	dev_kfree_skb(q->rx_head);
-	q->rx_head = NULL;
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/eeprom.c
@@ -51,7 +51,7 @@
 		goto out_put_node;
 	}
 
-	offset = be32_to_cpup(list);
+	offset += be32_to_cpup(list);
 	ret = mtd_read(mtd, offset, len, &retlen, eep);
 	put_mtd_device(mtd);
 	if (ret)
@@ -146,10 +146,13 @@
 		}
 
 		if (mt76_string_prop_find(country, dev->alpha2) ||
-		    mt76_string_prop_find(regd, region_name))
+		    mt76_string_prop_find(regd, region_name)) {
+			of_node_put(np);
 			return cur;
+		}
 	}
 
+	of_node_put(np);
 	return fallback;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mac80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mac80211.c
@@ -99,6 +99,27 @@
 };
 EXPORT_SYMBOL_GPL(mt76_rates);
 
+static const struct cfg80211_sar_freq_ranges mt76_sar_freq_ranges[] = {
+	{ .start_freq = 2402, .end_freq = 2494, },
+	{ .start_freq = 5150, .end_freq = 5350, },
+	{ .start_freq = 5350, .end_freq = 5470, },
+	{ .start_freq = 5470, .end_freq = 5725, },
+	{ .start_freq = 5725, .end_freq = 5950, },
+	{ .start_freq = 5945, .end_freq = 6165, },
+	{ .start_freq = 6165, .end_freq = 6405, },
+	{ .start_freq = 6405, .end_freq = 6525, },
+	{ .start_freq = 6525, .end_freq = 6705, },
+	{ .start_freq = 6705, .end_freq = 6865, },
+	{ .start_freq = 6865, .end_freq = 7125, },
+};
+
+const struct cfg80211_sar_capa mt76_sar_capa = {
+	.type = NL80211_SAR_TYPE_POWER,
+	.num_freq_ranges = ARRAY_SIZE(mt76_sar_freq_ranges),
+	.freq_ranges = &mt76_sar_freq_ranges[0],
+};
+EXPORT_SYMBOL_GPL(mt76_sar_capa);
+
 static int mt76_led_init(struct mt76_dev *dev)
 {
 	struct device_node *np = dev->dev->of_node;
@@ -123,6 +144,7 @@
 		if (!of_property_read_u32(np, "led-sources", &led_pin))
 			dev->led_pin = led_pin;
 		dev->led_al = of_property_read_bool(np, "led-active-low");
+		of_node_put(np);
 	}
 
 	return led_classdev_register(dev->dev, &dev->led_cdev);
@@ -427,6 +449,7 @@
 	dev->hw = hw;
 	dev->dev = pdev;
 	dev->drv = drv_ops;
+	dev->dma_dev = pdev;
 
 	phy = &dev->phy;
 	phy->dev = dev;
@@ -1100,7 +1123,7 @@
 			continue;
 
 		mtxq = (struct mt76_txq *)sta->txq[i]->drv_priv;
-		mtxq->wcid = wcid;
+		mtxq->wcid = wcid->idx;
 	}
 
 	ewma_signal_init(&wcid->rssi);
@@ -1194,6 +1217,59 @@
 }
 EXPORT_SYMBOL_GPL(mt76_get_txpower);
 
+int mt76_init_sar_power(struct ieee80211_hw *hw,
+			const struct cfg80211_sar_specs *sar)
+{
+	struct mt76_phy *phy = hw->priv;
+	const struct cfg80211_sar_capa *capa = hw->wiphy->sar_capa;
+	int i;
+
+	if (sar->type != NL80211_SAR_TYPE_POWER || !sar->num_sub_specs)
+		return -EINVAL;
+
+	for (i = 0; i < sar->num_sub_specs; i++) {
+		u32 index = sar->sub_specs[i].freq_range_index;
+		/* SAR specifies power limitaton in 0.25dbm */
+		s32 power = sar->sub_specs[i].power >> 1;
+
+		if (power > 127 || power < -127)
+			power = 127;
+
+		phy->frp[index].range = &capa->freq_ranges[index];
+		phy->frp[index].power = power;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(mt76_init_sar_power);
+
+int mt76_get_sar_power(struct mt76_phy *phy,
+		       struct ieee80211_channel *chan,
+		       int power)
+{
+	const struct cfg80211_sar_capa *capa = phy->hw->wiphy->sar_capa;
+	int freq, i;
+
+	if (!capa || !phy->frp)
+		return power;
+
+	if (power > 127 || power < -127)
+		power = 127;
+
+	freq = ieee80211_channel_to_frequency(chan->hw_value, chan->band);
+	for (i = 0 ; i < capa->num_freq_ranges; i++) {
+		if (phy->frp[i].range &&
+		    freq >= phy->frp[i].range->start_freq &&
+		    freq < phy->frp[i].range->end_freq) {
+			power = min_t(int, phy->frp[i].power, power);
+			break;
+		}
+	}
+
+	return power;
+}
+EXPORT_SYMBOL_GPL(mt76_get_sar_power);
+
 static void
 __mt76_csa_finish(void *priv, u8 *mac, struct ieee80211_vif *vif)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76.h
@@ -19,7 +19,7 @@
 
 #define MT_MCU_RING_SIZE	32
 #define MT_RX_BUF_SIZE		2048
-#define MT_SKB_HEAD_LEN		128
+#define MT_SKB_HEAD_LEN		256
 
 #define MT_MAX_NON_AQL_PKT	16
 #define MT_TXQ_FREE_THR		32
@@ -195,8 +195,8 @@
 		     u32 ring_base);
 
 	int (*tx_queue_skb)(struct mt76_dev *dev, struct mt76_queue *q,
-			    struct sk_buff *skb, struct mt76_wcid *wcid,
-			    struct ieee80211_sta *sta);
+			    enum mt76_txq_id qid, struct sk_buff *skb,
+			    struct mt76_wcid *wcid, struct ieee80211_sta *sta);
 
 	int (*tx_queue_skb_raw)(struct mt76_dev *dev, struct mt76_queue *q,
 				struct sk_buff *skb, u32 tx_info);
@@ -263,7 +263,7 @@
 };
 
 struct mt76_txq {
-	struct mt76_wcid *wcid;
+	u16 wcid;
 
 	u16 agg_ssn;
 	bool send_bar;
@@ -545,6 +545,11 @@
 	s8 chain_signal[IEEE80211_MAX_CHAINS];
 };
 
+struct mt76_freq_range_power {
+	const struct cfg80211_sar_freq_ranges *range;
+	s8 power;
+};
+
 struct mt76_testmode_ops {
 	int (*set_state)(struct mt76_phy *phy, enum mt76_testmode_state state);
 	int (*set_params)(struct mt76_phy *phy, struct nlattr **tb,
@@ -636,6 +641,8 @@
 		struct sk_buff **tail;
 		u16 seqno;
 	} rx_amsdu[__MT_RXQ_MAX];
+
+	struct mt76_freq_range_power *frp;
 };
 
 struct mt76_dev {
@@ -660,6 +667,7 @@
 	const struct mt76_driver_ops *drv;
 	const struct mt76_mcu_ops *mcu_ops;
 	struct device *dev;
+	struct device *dma_dev;
 
 	struct mt76_mcu mcu;
 
@@ -769,6 +777,7 @@
 }
 
 extern struct ieee80211_rate mt76_rates[12];
+extern const struct cfg80211_sar_capa mt76_sar_capa;
 
 #define __mt76_rr(dev, ...)	(dev)->bus->rr((dev), __VA_ARGS__)
 #define __mt76_wr(dev, ...)	(dev)->bus->wr((dev), __VA_ARGS__)
@@ -820,10 +829,11 @@
 
 #define mt76_poll(dev, ...) __mt76_poll(&((dev)->mt76), __VA_ARGS__)
 
-bool __mt76_poll_msec(struct mt76_dev *dev, u32 offset, u32 mask, u32 val,
-		      int timeout);
-
-#define mt76_poll_msec(dev, ...) __mt76_poll_msec(&((dev)->mt76), __VA_ARGS__)
+bool ____mt76_poll_msec(struct mt76_dev *dev, u32 offset, u32 mask, u32 val,
+			int timeout, int kick);
+#define __mt76_poll_msec(...)         ____mt76_poll_msec(__VA_ARGS__, 10)
+#define mt76_poll_msec(dev, ...)      ____mt76_poll_msec(&((dev)->mt76), __VA_ARGS__, 10)
+#define mt76_poll_msec_tick(dev, ...) ____mt76_poll_msec(&((dev)->mt76), __VA_ARGS__)
 
 void mt76_mmio_init(struct mt76_dev *dev, void __iomem *regs);
 void mt76_pci_disable_aspm(struct pci_dev *pdev);
@@ -869,7 +879,13 @@
 int mt76_register_phy(struct mt76_phy *phy, bool vht,
 		      struct ieee80211_rate *rates, int n_rates);
 
-struct dentry *mt76_register_debugfs(struct mt76_dev *dev);
+struct dentry *mt76_register_debugfs_fops(struct mt76_dev *dev,
+					  const struct file_operations *ops);
+static inline struct dentry *mt76_register_debugfs(struct mt76_dev *dev)
+{
+	return mt76_register_debugfs_fops(dev, NULL);
+}
+
 int mt76_queues_read(struct seq_file *s, void *data);
 void mt76_seq_puts_array(struct seq_file *file, const char *str,
 			 s8 *val, int len);
@@ -1015,8 +1031,9 @@
 static inline u8 mt76_tx_power_nss_delta(u8 nss)
 {
 	static const u8 nss_delta[4] = { 0, 6, 9, 12 };
+	u8 idx = nss - 1;
 
-	return nss_delta[nss - 1];
+	return (idx < ARRAY_SIZE(nss_delta)) ? nss_delta[idx] : 0;
 }
 
 static inline bool mt76_testmode_enabled(struct mt76_phy *phy)
@@ -1111,6 +1128,11 @@
 
 int mt76_get_txpower(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 		     int *dbm);
+int mt76_init_sar_power(struct ieee80211_hw *hw,
+			const struct cfg80211_sar_specs *sar);
+int mt76_get_sar_power(struct mt76_phy *phy,
+		       struct ieee80211_channel *chan,
+		       int power);
 
 void mt76_csa_check(struct mt76_dev *dev);
 void mt76_csa_finish(struct mt76_dev *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7603/beacon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7603/beacon.c
@@ -10,12 +10,31 @@
 };
 
 static void
+mt7603_mac_stuck_beacon_recovery(struct mt7603_dev *dev)
+{
+	if (dev->beacon_check % 5 != 4)
+		return;
+
+	mt76_clear(dev, MT_WPDMA_GLO_CFG, MT_WPDMA_GLO_CFG_TX_DMA_EN);
+	mt76_set(dev, MT_SCH_4, MT_SCH_4_RESET);
+	mt76_clear(dev, MT_SCH_4, MT_SCH_4_RESET);
+	mt76_set(dev, MT_WPDMA_GLO_CFG, MT_WPDMA_GLO_CFG_TX_DMA_EN);
+
+	mt76_set(dev, MT_WF_CFG_OFF_WOCCR, MT_WF_CFG_OFF_WOCCR_TMAC_GC_DIS);
+	mt76_set(dev, MT_ARB_SCR, MT_ARB_SCR_TX_DISABLE);
+	mt76_clear(dev, MT_ARB_SCR, MT_ARB_SCR_TX_DISABLE);
+	mt76_clear(dev, MT_WF_CFG_OFF_WOCCR, MT_WF_CFG_OFF_WOCCR_TMAC_GC_DIS);
+}
+
+static void
 mt7603_update_beacon_iter(void *priv, u8 *mac, struct ieee80211_vif *vif)
 {
 	struct mt7603_dev *dev = (struct mt7603_dev *)priv;
 	struct mt76_dev *mdev = &dev->mt76;
 	struct mt7603_vif *mvif = (struct mt7603_vif *)vif->drv_priv;
 	struct sk_buff *skb = NULL;
+	u32 om_idx = mvif->idx;
+	u32 val;
 
 	if (!(mdev->beacon_mask & BIT(mvif->idx)))
 		return;
@@ -24,20 +43,33 @@
 	if (!skb)
 		return;
 
-	mt76_tx_queue_skb(dev, dev->mphy.q_tx[MT_TXQ_BEACON], skb,
-			  &mvif->sta.wcid, NULL);
+	if (om_idx)
+		om_idx |= 0x10;
+	val = MT_DMA_FQCR0_BUSY | MT_DMA_FQCR0_MODE |
+		FIELD_PREP(MT_DMA_FQCR0_TARGET_BSS, om_idx) |
+		FIELD_PREP(MT_DMA_FQCR0_DEST_PORT_ID, 3) |
+		FIELD_PREP(MT_DMA_FQCR0_DEST_QUEUE_ID, 8);
 
 	spin_lock_bh(&dev->ps_lock);
-	mt76_wr(dev, MT_DMA_FQCR0, MT_DMA_FQCR0_BUSY |
-		FIELD_PREP(MT_DMA_FQCR0_TARGET_WCID, mvif->sta.wcid.idx) |
-		FIELD_PREP(MT_DMA_FQCR0_TARGET_QID,
-			   dev->mphy.q_tx[MT_TXQ_CAB]->hw_idx) |
-		FIELD_PREP(MT_DMA_FQCR0_DEST_PORT_ID, 3) |
-		FIELD_PREP(MT_DMA_FQCR0_DEST_QUEUE_ID, 8));
 
-	if (!mt76_poll(dev, MT_DMA_FQCR0, MT_DMA_FQCR0_BUSY, 0, 5000))
+	mt76_wr(dev, MT_DMA_FQCR0, val |
+		FIELD_PREP(MT_DMA_FQCR0_TARGET_QID, MT_TX_HW_QUEUE_BCN));
+	if (!mt76_poll(dev, MT_DMA_FQCR0, MT_DMA_FQCR0_BUSY, 0, 5000)) {
+		dev->beacon_check = MT7603_WATCHDOG_TIMEOUT;
+		goto out;
+	}
+
+	mt76_wr(dev, MT_DMA_FQCR0, val |
+		FIELD_PREP(MT_DMA_FQCR0_TARGET_QID, MT_TX_HW_QUEUE_BMC));
+	if (!mt76_poll(dev, MT_DMA_FQCR0, MT_DMA_FQCR0_BUSY, 0, 5000)) {
 		dev->beacon_check = MT7603_WATCHDOG_TIMEOUT;
+		goto out;
+	}
 
+	mt76_tx_queue_skb(dev, dev->mphy.q_tx[MT_TXQ_BEACON],
+			  MT_TXQ_BEACON, skb, &mvif->sta.wcid, NULL);
+
+out:
 	spin_unlock_bh(&dev->ps_lock);
 }
 
@@ -81,6 +113,18 @@
 	data.dev = dev;
 	__skb_queue_head_init(&data.q);
 
+	/* Flush all previous CAB queue packets and beacons */
+	mt76_wr(dev, MT_WF_ARB_CAB_FLUSH, GENMASK(30, 16) | BIT(0));
+
+	mt76_queue_tx_cleanup(dev, dev->mphy.q_tx[MT_TXQ_CAB], false);
+	mt76_queue_tx_cleanup(dev, dev->mphy.q_tx[MT_TXQ_BEACON], false);
+
+	if (dev->mphy.q_tx[MT_TXQ_BEACON]->queued > 0)
+		dev->beacon_check++;
+	else
+		dev->beacon_check = 0;
+	mt7603_mac_stuck_beacon_recovery(dev);
+
 	q = dev->mphy.q_tx[MT_TXQ_BEACON];
 	spin_lock_bh(&q->lock);
 	ieee80211_iterate_active_interfaces_atomic(mt76_hw(dev),
@@ -89,14 +133,9 @@
 	mt76_queue_kick(dev, q);
 	spin_unlock_bh(&q->lock);
 
-	/* Flush all previous CAB queue packets */
-	mt76_wr(dev, MT_WF_ARB_CAB_FLUSH, GENMASK(30, 16) | BIT(0));
-
-	mt76_queue_tx_cleanup(dev, dev->mphy.q_tx[MT_TXQ_CAB], false);
-
 	mt76_csa_check(mdev);
 	if (mdev->csa_complete)
-		goto out;
+		return;
 
 	q = dev->mphy.q_tx[MT_TXQ_CAB];
 	do {
@@ -108,7 +147,7 @@
 		 skb_queue_len(&data.q) < 8);
 
 	if (skb_queue_empty(&data.q))
-		goto out;
+		return;
 
 	for (i = 0; i < ARRAY_SIZE(data.tail); i++) {
 		if (!data.tail[i])
@@ -123,7 +162,7 @@
 		struct ieee80211_vif *vif = info->control.vif;
 		struct mt7603_vif *mvif = (struct mt7603_vif *)vif->drv_priv;
 
-		mt76_tx_queue_skb(dev, q, skb, &mvif->sta.wcid, NULL);
+		mt76_tx_queue_skb(dev, q, MT_TXQ_CAB, skb, &mvif->sta.wcid, NULL);
 	}
 	mt76_queue_kick(dev, q);
 	spin_unlock_bh(&q->lock);
@@ -136,11 +175,6 @@
 		MT_WF_ARB_CAB_START_BSSn(0) |
 		(MT_WF_ARB_CAB_START_BSS0n(1) *
 		 ((1 << (MT7603_MAX_INTERFACES - 1)) - 1)));
-
-out:
-	mt76_queue_tx_cleanup(dev, dev->mphy.q_tx[MT_TXQ_BEACON], false);
-	if (dev->mphy.q_tx[MT_TXQ_BEACON]->queued > hweight8(mdev->beacon_mask))
-		dev->beacon_check++;
 }
 
 void mt7603_beacon_set_timer(struct mt7603_dev *dev, int idx, int intval)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7603/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7603/core.c
@@ -42,11 +42,13 @@
 	}
 
 	if (intr & MT_INT_RX_DONE(0)) {
+		dev->rx_pse_check = 0;
 		mt7603_irq_disable(dev, MT_INT_RX_DONE(0));
 		napi_schedule(&dev->mt76.napi[0]);
 	}
 
 	if (intr & MT_INT_RX_DONE(1)) {
+		dev->rx_pse_check = 0;
 		mt7603_irq_disable(dev, MT_INT_RX_DONE(1));
 		napi_schedule(&dev->mt76.napi[1]);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
@@ -525,6 +525,10 @@
 	if (rxd2 & MT_RXD2_NORMAL_TKIP_MIC_ERR)
 		status->flag |= RX_FLAG_MMIC_ERROR;
 
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd2 & MT_RXD2_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	if (FIELD_GET(MT_RXD2_NORMAL_SEC_MODE, rxd2) != 0 &&
 	    !(rxd2 & (MT_RXD2_NORMAL_CLM | MT_RXD2_NORMAL_CM))) {
 		status->flag |= RX_FLAG_DECRYPTED;
@@ -1280,8 +1284,11 @@
 	if (wcidx >= MT7603_WTBL_STA || !sta)
 		goto out;
 
-	if (mt7603_fill_txs(dev, msta, &info, txs_data))
+	if (mt7603_fill_txs(dev, msta, &info, txs_data)) {
+		spin_lock_bh(&dev->mt76.rx_lock);
 		ieee80211_tx_status_noskb(mt76_hw(dev), sta, &info);
+		spin_unlock_bh(&dev->mt76.rx_lock);
+	}
 
 out:
 	rcu_read_unlock();
@@ -1554,20 +1561,29 @@
 {
 	u32 addr, val;
 
-	if (mt76_rr(dev, MT_MCU_DEBUG_RESET) & MT_MCU_DEBUG_RESET_QUEUES)
-		return true;
-
 	if (mt7603_rx_fifo_busy(dev))
-		return false;
+		goto out;
 
 	addr = mt7603_reg_map(dev, MT_CLIENT_BASE_PHYS_ADDR + MT_CLIENT_STATUS);
 	mt76_wr(dev, addr, 3);
 	val = mt76_rr(dev, addr) >> 16;
 
-	if (is_mt7628(dev) && (val & 0x4001) == 0x4001)
-		return true;
+	if (!(val & BIT(0)))
+		return false;
+
+	if (is_mt7628(dev))
+		val &= 0xa000;
+	else
+		val &= 0x8000;
+	if (!val)
+		return false;
 
-	return (val & 0x8001) == 0x8001 || (val & 0xe001) == 0xe001;
+out:
+	if (mt76_rr(dev, MT_INT_SOURCE_CSR) &
+	    (MT_INT_RX_DONE(0) | MT_INT_RX_DONE(1)))
+		return false;
+
+	return true;
 }
 
 static bool
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7603/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7603/main.c
@@ -74,7 +74,7 @@
 	mt7603_wtbl_init(dev, idx, mvif->idx, bc_addr);
 
 	mtxq = (struct mt76_txq *)vif->txq->drv_priv;
-	mtxq->wcid = &mvif->sta.wcid;
+	mtxq->wcid = idx;
 	rcu_assign_pointer(dev->mt76.wcid[idx], &mvif->sta.wcid);
 
 out:
@@ -620,6 +620,9 @@
 	struct ieee80211_sta_rates *sta_rates = rcu_dereference(sta->rates);
 	int i;
 
+	if (!sta_rates)
+		return;
+
 	spin_lock_bh(&dev->mt76.lock);
 	for (i = 0; i < ARRAY_SIZE(msta->rates); i++) {
 		msta->rates[i].idx = sta_rates->rate[i].idx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7603/regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7603/regs.h
@@ -462,6 +462,11 @@
 #define MT_WF_SEC_BASE			0x21a00
 #define MT_WF_SEC(ofs)			(MT_WF_SEC_BASE + (ofs))
 
+#define MT_WF_CFG_OFF_BASE		0x21e00
+#define MT_WF_CFG_OFF(ofs)		(MT_WF_CFG_OFF_BASE + (ofs))
+#define MT_WF_CFG_OFF_WOCCR		MT_WF_CFG_OFF(0x004)
+#define MT_WF_CFG_OFF_WOCCR_TMAC_GC_DIS	BIT(4)
+
 #define MT_SEC_SCR			MT_WF_SEC(0x004)
 #define MT_SEC_SCR_MASK_ORDER		GENMASK(1, 0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/debugfs.c
@@ -3,6 +3,33 @@
 #include "mt7615.h"
 
 static int
+mt7615_reg_set(void *data, u64 val)
+{
+	struct mt7615_dev *dev = data;
+
+	mt7615_mutex_acquire(dev);
+	mt76_wr(dev, dev->mt76.debugfs_reg, val);
+	mt7615_mutex_release(dev);
+
+	return 0;
+}
+
+static int
+mt7615_reg_get(void *data, u64 *val)
+{
+	struct mt7615_dev *dev = data;
+
+	mt7615_mutex_acquire(dev);
+	*val = mt76_rr(dev, dev->mt76.debugfs_reg);
+	mt7615_mutex_release(dev);
+
+	return 0;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(fops_regval, mt7615_reg_get, mt7615_reg_set,
+			 "0x%08llx\n");
+
+static int
 mt7615_radar_pattern_set(void *data, u64 val)
 {
 	struct mt7615_dev *dev = data;
@@ -506,7 +533,7 @@
 {
 	struct dentry *dir;
 
-	dir = mt76_register_debugfs(&dev->mt76);
+	dir = mt76_register_debugfs_fops(&dev->mt76, &fops_regval);
 	if (!dir)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
@@ -123,12 +123,12 @@
 	case MT_EE_5GHZ:
 		dev->mphy.cap.has_5ghz = true;
 		break;
-	case MT_EE_2GHZ:
-		dev->mphy.cap.has_2ghz = true;
-		break;
 	case MT_EE_DBDC:
 		dev->dbdc_support = true;
 		fallthrough;
+	case MT_EE_2GHZ:
+		dev->mphy.cap.has_2ghz = true;
+		break;
 	default:
 		dev->mphy.cap.has_2ghz = true;
 		dev->mphy.cap.has_5ghz = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/init.c
@@ -49,12 +49,17 @@
 {
 	struct wiphy *wiphy = mt76_hw(dev)->wiphy;
 	struct device *hwmon;
+	const char *name;
 
 	if (!IS_REACHABLE(CONFIG_HWMON))
 		return 0;
 
-	hwmon = devm_hwmon_device_register_with_groups(&wiphy->dev,
-						       wiphy_name(wiphy), dev,
+	name = devm_kasprintf(&wiphy->dev, GFP_KERNEL, "mt7615_%s",
+			      wiphy_name(wiphy));
+	if (!name)
+		return -ENOMEM;
+
+	hwmon = devm_hwmon_device_register_with_groups(&wiphy->dev, name, dev,
 						       mt7615_hwmon_groups);
 	if (IS_ERR(hwmon))
 		return PTR_ERR(hwmon);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -286,9 +286,16 @@
 	if (rxd2 & MT_RXD2_NORMAL_AMSDU_ERR)
 		return -EINVAL;
 
+	hdr_trans = rxd1 & MT_RXD1_NORMAL_HDR_TRANS;
+	if (hdr_trans && (rxd2 & MT_RXD2_NORMAL_CM))
+		return -EINVAL;
+
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd2 & MT_RXD2_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	unicast = (rxd1 & MT_RXD1_NORMAL_ADDR_TYPE) == MT_RXD1_NORMAL_U2M;
 	idx = FIELD_GET(MT_RXD2_NORMAL_WLAN_IDX, rxd2);
-	hdr_trans = rxd1 & MT_RXD1_NORMAL_HDR_TRANS;
 	status->wcid = mt7615_rx_get_wcid(dev, idx, unicast);
 
 	if (status->wcid) {
@@ -755,12 +762,15 @@
 	if (info->flags & IEEE80211_TX_CTL_NO_ACK)
 		txwi[3] |= cpu_to_le32(MT_TXD3_NO_ACK);
 
-	txwi[7] = FIELD_PREP(MT_TXD7_TYPE, fc_type) |
-		  FIELD_PREP(MT_TXD7_SUB_TYPE, fc_stype) |
-		  FIELD_PREP(MT_TXD7_SPE_IDX, 0x18);
-	if (!is_mmio)
-		txwi[8] = FIELD_PREP(MT_TXD8_L_TYPE, fc_type) |
-			  FIELD_PREP(MT_TXD8_L_SUB_TYPE, fc_stype);
+	val = FIELD_PREP(MT_TXD7_TYPE, fc_type) |
+	      FIELD_PREP(MT_TXD7_SUB_TYPE, fc_stype) |
+	      FIELD_PREP(MT_TXD7_SPE_IDX, 0x18);
+	txwi[7] = cpu_to_le32(val);
+	if (!is_mmio) {
+		val = FIELD_PREP(MT_TXD8_L_TYPE, fc_type) |
+		      FIELD_PREP(MT_TXD8_L_SUB_TYPE, fc_stype);
+		txwi[8] = cpu_to_le32(val);
+	}
 
 	return 0;
 }
@@ -859,7 +869,10 @@
 
 		msta = list_first_entry(&sta_poll_list, struct mt7615_sta,
 					poll_list);
+
+		spin_lock_bh(&dev->sta_poll_lock);
 		list_del_init(&msta->poll_list);
+		spin_unlock_bh(&dev->sta_poll_lock);
 
 		addr = mt7615_mac_wtbl_addr(dev, msta->wcid.idx) + 19 * 4;
 
@@ -1028,7 +1041,7 @@
 	offset %= 32;
 
 	val = mt76_rr(dev, addr);
-	val >>= (tid % 32);
+	val >>= offset;
 
 	if (offset > 20) {
 		addr += 4;
@@ -1486,40 +1499,52 @@
 	if (wcid->ext_phy && dev->mt76.phy2)
 		mphy = dev->mt76.phy2;
 
-	if (mt7615_fill_txs(dev, msta, &info, txs_data))
+	if (mt7615_fill_txs(dev, msta, &info, txs_data)) {
+		spin_lock_bh(&dev->mt76.rx_lock);
 		ieee80211_tx_status_noskb(mphy->hw, sta, &info);
+		spin_unlock_bh(&dev->mt76.rx_lock);
+	}
 
 out:
 	rcu_read_unlock();
 }
 
 static void
-mt7615_mac_tx_free_token(struct mt7615_dev *dev, u16 token)
+mt7615_txwi_free(struct mt7615_dev *dev, struct mt76_txwi_cache *txwi)
 {
 	struct mt76_dev *mdev = &dev->mt76;
-	struct mt76_txwi_cache *txwi;
 	__le32 *txwi_data;
 	u32 val;
 	u8 wcid;
 
-	trace_mac_tx_free(dev, token);
-	txwi = mt76_token_put(mdev, token);
-	if (!txwi)
-		return;
+	mt7615_txp_skb_unmap(mdev, txwi);
+	if (!txwi->skb)
+		goto out;
 
 	txwi_data = (__le32 *)mt76_get_txwi_ptr(mdev, txwi);
 	val = le32_to_cpu(txwi_data[1]);
 	wcid = FIELD_GET(MT_TXD1_WLAN_IDX, val);
+	mt76_tx_complete_skb(mdev, wcid, txwi->skb);
 
-	mt7615_txp_skb_unmap(mdev, txwi);
-	if (txwi->skb) {
-		mt76_tx_complete_skb(mdev, wcid, txwi->skb);
-		txwi->skb = NULL;
-	}
-
+out:
+	txwi->skb = NULL;
 	mt76_put_txwi(mdev, txwi);
 }
 
+static void
+mt7615_mac_tx_free_token(struct mt7615_dev *dev, u16 token)
+{
+	struct mt76_dev *mdev = &dev->mt76;
+	struct mt76_txwi_cache *txwi;
+
+	trace_mac_tx_free(dev, token);
+	txwi = mt76_token_put(mdev, token);
+	if (!txwi)
+		return;
+
+	mt7615_txwi_free(dev, txwi);
+}
+
 static void mt7615_mac_tx_free(struct mt7615_dev *dev, struct sk_buff *skb)
 {
 	struct mt7615_tx_free *free = (struct mt7615_tx_free *)skb->data;
@@ -1713,7 +1738,7 @@
 	struct mt7615_dev *dev = phy->dev;
 	int false_cca = ofdm ? phy->false_cca_ofdm : phy->false_cca_cck;
 	bool ext_phy = phy != &dev->phy;
-	u16 def_th = ofdm ? -98 : -110;
+	s16 def_th = ofdm ? -98 : -110;
 	bool update = false;
 	s8 *sensitivity;
 	int signal;
@@ -1981,6 +2006,14 @@
 	    test_bit(MT76_HW_SCHED_SCANNING, &dev->mphy.state))
 		goto out;
 
+	if (mutex_is_locked(&dev->mt76.mutex))
+		/* if mt76 mutex is held we should not put the device
+		 * to sleep since we are currently accessing device
+		 * register map. We need to wait for the next power_save
+		 * trigger.
+		 */
+		goto out;
+
 	if (time_is_after_jiffies(dev->pm.last_activity + delta)) {
 		delta = dev->pm.last_activity + delta - jiffies;
 		goto out;
@@ -2026,16 +2059,8 @@
 	int id;
 
 	spin_lock_bh(&dev->mt76.token_lock);
-	idr_for_each_entry(&dev->mt76.token, txwi, id) {
-		mt7615_txp_skb_unmap(&dev->mt76, txwi);
-		if (txwi->skb) {
-			struct ieee80211_hw *hw;
-
-			hw = mt76_tx_status_get_hw(&dev->mt76, txwi->skb);
-			ieee80211_free_txskb(hw, txwi->skb);
-		}
-		mt76_put_txwi(&dev->mt76, txwi);
-	}
+	idr_for_each_entry(&dev->mt76.token, txwi, id)
+		mt7615_txwi_free(dev, txwi);
 	spin_unlock_bh(&dev->mt76.token_lock);
 	idr_destroy(&dev->mt76.token);
 }
@@ -2251,7 +2276,7 @@
 			break;
 
 		skb_pull(skb, sizeof(struct mt7615_mcu_rxd));
-		if (data + skb->len - dump > MT76_CONNAC_COREDUMP_SZ) {
+		if (!dump || data + skb->len - dump > MT76_CONNAC_COREDUMP_SZ) {
 			dev_kfree_skb(skb);
 			continue;
 		}
@@ -2261,6 +2286,8 @@
 
 		dev_kfree_skb(skb);
 	}
-	dev_coredumpv(dev->mt76.dev, dump, MT76_CONNAC_COREDUMP_SZ,
-		      GFP_KERNEL);
+
+	if (dump)
+		dev_coredumpv(dev->mt76.dev, dump, MT76_CONNAC_COREDUMP_SZ,
+			      GFP_KERNEL);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/main.c
@@ -135,8 +135,6 @@
 	int i;
 
 	switch (type) {
-	case NL80211_IFTYPE_MESH_POINT:
-	case NL80211_IFTYPE_ADHOC:
 	case NL80211_IFTYPE_STATION:
 		/* prefer hw bssid slot 1-3 */
 		i = get_free_idx(mask, HW_BSSID_1, HW_BSSID_3);
@@ -160,6 +158,8 @@
 			return HW_BSSID_0;
 
 		break;
+	case NL80211_IFTYPE_ADHOC:
+	case NL80211_IFTYPE_MESH_POINT:
 	case NL80211_IFTYPE_MONITOR:
 	case NL80211_IFTYPE_AP:
 		/* ap uses hw bssid 0 and ext bssid */
@@ -211,11 +211,9 @@
 	mvif->mt76.omac_idx = idx;
 
 	mvif->mt76.band_idx = ext_phy;
-	if (mt7615_ext_phy(dev))
-		mvif->mt76.wmm_idx = ext_phy * (MT7615_MAX_WMM_SETS / 2) +
-				mvif->mt76.idx % (MT7615_MAX_WMM_SETS / 2);
-	else
-		mvif->mt76.wmm_idx = mvif->mt76.idx % MT7615_MAX_WMM_SETS;
+	mvif->mt76.wmm_idx = vif->type != NL80211_IFTYPE_AP;
+	if (ext_phy)
+		mvif->mt76.wmm_idx += 2;
 
 	dev->mt76.vif_mask |= BIT(mvif->mt76.idx);
 	dev->omac_mask |= BIT_ULL(mvif->mt76.omac_idx);
@@ -237,7 +235,7 @@
 	rcu_assign_pointer(dev->mt76.wcid[idx], &mvif->sta.wcid);
 	if (vif->txq) {
 		mtxq = (struct mt76_txq *)vif->txq->drv_priv;
-		mtxq->wcid = &mvif->sta.wcid;
+		mtxq->wcid = idx;
 	}
 
 	ret = mt7615_mcu_add_dev_info(phy, vif, true);
@@ -292,7 +290,8 @@
 	if (hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
 		return;
 
-	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR))
+	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR) &&
+	    !(mphy->chandef.chan->flags & IEEE80211_CHAN_RADAR))
 		return;
 
 	if (mphy->chandef.chan->center_freq == chandef->chan->center_freq &&
@@ -684,6 +683,9 @@
 	struct ieee80211_sta_rates *sta_rates = rcu_dereference(sta->rates);
 	int i;
 
+	if (!sta_rates)
+		return;
+
 	spin_lock_bh(&dev->mt76.lock);
 	for (i = 0; i < ARRAY_SIZE(msta->rates); i++) {
 		msta->rates[i].idx = sta_rates->rate[i].idx;
@@ -1185,12 +1187,16 @@
 	struct mt7615_dev *dev = mt7615_hw_dev(hw);
 	struct mt7615_sta *msta = (struct mt7615_sta *)sta->drv_priv;
 
+	mt7615_mutex_acquire(dev);
+
 	if (enabled)
 		set_bit(MT_WCID_FLAG_HDR_TRANS, &msta->wcid.flags);
 	else
 		clear_bit(MT_WCID_FLAG_HDR_TRANS, &msta->wcid.flags);
 
 	mt7615_mcu_set_sta_decap_offload(dev, vif, sta);
+
+	mt7615_mutex_release(dev);
 }
 
 #ifdef CONFIG_PM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
@@ -385,10 +385,11 @@
 	}
 
 	mt7622_trigger_hif_int(dev, false);
-
-	pm->stats.last_doze_event = jiffies;
-	pm->stats.awake_time += pm->stats.last_doze_event -
-				pm->stats.last_wake_event;
+	if (!err) {
+		pm->stats.last_doze_event = jiffies;
+		pm->stats.awake_time += pm->stats.last_doze_event -
+					pm->stats.last_wake_event;
+	}
 out:
 	mutex_unlock(&pm->mutex);
 
@@ -808,7 +809,8 @@
 
 static int
 mt7615_mcu_bss_basic_tlv(struct sk_buff *skb, struct ieee80211_vif *vif,
-			 struct ieee80211_sta *sta, bool enable)
+			 struct ieee80211_sta *sta, struct mt7615_phy *phy,
+			 bool enable)
 {
 	struct mt7615_vif *mvif = (struct mt7615_vif *)vif->drv_priv;
 	u32 type = vif->p2p ? NETWORK_P2P : NETWORK_INFRA;
@@ -821,6 +823,7 @@
 	switch (vif->type) {
 	case NL80211_IFTYPE_MESH_POINT:
 	case NL80211_IFTYPE_AP:
+	case NL80211_IFTYPE_MONITOR:
 		break;
 	case NL80211_IFTYPE_STATION:
 		/* TODO: enable BSS_INFO_UAPSD & BSS_INFO_PM */
@@ -840,14 +843,19 @@
 	}
 
 	bss = (struct bss_info_basic *)tlv;
-	memcpy(bss->bssid, vif->bss_conf.bssid, ETH_ALEN);
-	bss->bcn_interval = cpu_to_le16(vif->bss_conf.beacon_int);
 	bss->network_type = cpu_to_le32(type);
-	bss->dtim_period = vif->bss_conf.dtim_period;
 	bss->bmc_tx_wlan_idx = wlan_idx;
 	bss->wmm_idx = mvif->mt76.wmm_idx;
 	bss->active = enable;
 
+	if (vif->type != NL80211_IFTYPE_MONITOR) {
+		memcpy(bss->bssid, vif->bss_conf.bssid, ETH_ALEN);
+		bss->bcn_interval = cpu_to_le16(vif->bss_conf.beacon_int);
+		bss->dtim_period = vif->bss_conf.dtim_period;
+	} else {
+		memcpy(bss->bssid, phy->mt76->macaddr, ETH_ALEN);
+	}
+
 	return 0;
 }
 
@@ -863,6 +871,7 @@
 	tlv = mt76_connac_mcu_add_tlv(skb, BSS_INFO_OMAC, sizeof(*omac));
 
 	switch (vif->type) {
+	case NL80211_IFTYPE_MONITOR:
 	case NL80211_IFTYPE_MESH_POINT:
 	case NL80211_IFTYPE_AP:
 		if (vif->p2p)
@@ -929,7 +938,7 @@
 	if (enable)
 		mt7615_mcu_bss_omac_tlv(skb, vif);
 
-	mt7615_mcu_bss_basic_tlv(skb, vif, sta, enable);
+	mt7615_mcu_bss_basic_tlv(skb, vif, sta, phy, enable);
 
 	if (enable && mvif->mt76.omac_idx >= EXT_BSSID_START &&
 	    mvif->mt76.omac_idx < REPEATER_BSSID_START)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c
@@ -28,8 +28,6 @@
 		return;
 
 	mt7615_init_work(dev);
-	if (dev->dbdc_support)
-		mt7615_register_ext_phy(dev);
 }
 
 static int mt7615_init_hardware(struct mt7615_dev *dev)
@@ -160,6 +158,12 @@
 	mt7615_init_txpower(dev, &dev->mphy.sband_2g.sband);
 	mt7615_init_txpower(dev, &dev->mphy.sband_5g.sband);
 
+	if (dev->dbdc_support) {
+		ret = mt7615_register_ext_phy(dev);
+		if (ret)
+			return ret;
+	}
+
 	return mt7615_init_debugfs(dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76_connac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76_connac.h
@@ -85,9 +85,14 @@
 
 extern const struct wiphy_wowlan_support mt76_connac_wowlan_support;
 
+static inline bool is_mt7922(struct mt76_dev *dev)
+{
+	return mt76_chip(dev) == 0x7922;
+}
+
 static inline bool is_mt7921(struct mt76_dev *dev)
 {
-	return mt76_chip(dev) == 0x7961;
+	return mt76_chip(dev) == 0x7961 || is_mt7922(dev);
 }
 
 static inline bool is_mt7663(struct mt76_dev *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76_connac_mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76_connac_mac.c
@@ -7,9 +7,6 @@
 {
 	struct mt76_dev *dev = phy->dev;
 
-	if (!pm->enable)
-		return 0;
-
 	if (mt76_is_usb(dev))
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76_connac_mcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76_connac_mcu.c
@@ -234,7 +234,7 @@
 	};
 	u16 ntlv;
 
-	ptlv = skb_put(skb, len);
+	ptlv = skb_put_zero(skb, len);
 	memcpy(ptlv, &tlv, sizeof(tlv));
 
 	ntlv = le16_to_cpu(ntlv_hdr->tlv_num);
@@ -295,7 +295,7 @@
 	}
 
 	if (sta_hdr)
-		sta_hdr->len = cpu_to_le16(sizeof(hdr));
+		le16_add_cpu(&sta_hdr->len, sizeof(hdr));
 
 	return skb_put_data(nskb, &hdr, sizeof(hdr));
 }
@@ -689,7 +689,7 @@
 		if (ht_cap->ht_supported)
 			mode |= PHY_TYPE_BIT_HT;
 
-		if (he_cap->has_he)
+		if (he_cap && he_cap->has_he)
 			mode |= PHY_TYPE_BIT_HE;
 	} else if (band == NL80211_BAND_5GHZ) {
 		mode |= PHY_TYPE_BIT_OFDM;
@@ -700,7 +700,7 @@
 		if (vht_cap->vht_supported)
 			mode |= PHY_TYPE_BIT_VHT;
 
-		if (he_cap->has_he)
+		if (he_cap && he_cap->has_he)
 			mode |= PHY_TYPE_BIT_HE;
 	}
 
@@ -719,6 +719,7 @@
 	struct sta_rec_state *state;
 	struct sta_rec_phy *phy;
 	struct tlv *tlv;
+	u16 supp_rates;
 
 	/* starec ht */
 	if (sta->ht_cap.ht_supported) {
@@ -767,7 +768,15 @@
 
 	tlv = mt76_connac_mcu_add_tlv(skb, STA_REC_RA, sizeof(*ra_info));
 	ra_info = (struct sta_rec_ra_info *)tlv;
-	ra_info->legacy = cpu_to_le16((u16)sta->supp_rates[band]);
+
+	supp_rates = sta->supp_rates[band];
+	if (band == NL80211_BAND_2GHZ)
+		supp_rates = FIELD_PREP(RA_LEGACY_OFDM, supp_rates >> 4) |
+			     FIELD_PREP(RA_LEGACY_CCK, supp_rates & 0xf);
+	else
+		supp_rates = FIELD_PREP(RA_LEGACY_OFDM, supp_rates);
+
+	ra_info->legacy = cpu_to_le16(supp_rates);
 
 	if (sta->ht_cap.ht_supported)
 		memcpy(ra_info->rx_mcs_bitmask, sta->ht_cap.mcs.rx_mask,
@@ -1284,6 +1293,8 @@
 		else
 			conn_type = CONNECTION_INFRA_AP;
 		basic_req.basic.conn_type = cpu_to_le32(conn_type);
+		/* Fully active/deactivate BSS network in AP mode only */
+		basic_req.basic.active = enable;
 		break;
 	case NL80211_IFTYPE_STATION:
 		if (vif->p2p)
@@ -1408,7 +1419,7 @@
 	set_bit(MT76_HW_SCANNING, &phy->state);
 	mvif->scan_seq_num = (mvif->scan_seq_num + 1) & 0x7f;
 
-	req = (struct mt76_connac_hw_scan_req *)skb_put(skb, sizeof(*req));
+	req = (struct mt76_connac_hw_scan_req *)skb_put_zero(skb, sizeof(*req));
 
 	req->seq_num = mvif->scan_seq_num | ext_phy << 7;
 	req->bss_idx = mvif->idx;
@@ -1437,8 +1448,16 @@
 	req->channel_min_dwell_time = cpu_to_le16(duration);
 	req->channel_dwell_time = cpu_to_le16(duration);
 
-	req->channels_num = min_t(u8, sreq->n_channels, 32);
-	req->ext_channels_num = min_t(u8, ext_channels_num, 32);
+	if (sreq->n_channels == 0 || sreq->n_channels > 64) {
+		req->channel_type = 0;
+		req->channels_num = 0;
+		req->ext_channels_num = 0;
+	} else {
+		req->channel_type = 4;
+		req->channels_num = min_t(u8, sreq->n_channels, 32);
+		req->ext_channels_num = min_t(u8, ext_channels_num, 32);
+	}
+
 	for (i = 0; i < req->channels_num + req->ext_channels_num; i++) {
 		if (i >= 32)
 			chan = &req->ext_channels[i - 32];
@@ -1448,7 +1467,6 @@
 		chan->band = scan_list[i]->band == NL80211_BAND_2GHZ ? 1 : 2;
 		chan->channel_num = scan_list[i]->hw_value;
 	}
-	req->channel_type = sreq->n_channels ? 4 : 0;
 
 	if (sreq->ie_len > 0) {
 		memcpy(req->ies, sreq->ie, sreq->ie_len);
@@ -1519,7 +1537,7 @@
 
 	mvif->scan_seq_num = (mvif->scan_seq_num + 1) & 0x7f;
 
-	req = (struct mt76_connac_sched_scan_req *)skb_put(skb, sizeof(*req));
+	req = (struct mt76_connac_sched_scan_req *)skb_put_zero(skb, sizeof(*req));
 	req->version = 1;
 	req->seq_num = mvif->scan_seq_num | ext_phy << 7;
 
@@ -1749,6 +1767,43 @@
 	}
 }
 
+static s8 mt76_connac_get_ch_power(struct mt76_phy *phy,
+				   struct ieee80211_channel *chan,
+				   s8 target_power)
+{
+	struct mt76_dev *dev = phy->dev;
+	struct ieee80211_supported_band *sband;
+	int i;
+
+	switch (chan->band) {
+	case NL80211_BAND_2GHZ:
+		sband = &phy->sband_2g.sband;
+		break;
+	case NL80211_BAND_5GHZ:
+		sband = &phy->sband_5g.sband;
+		break;
+	default:
+		return target_power;
+	}
+
+	for (i = 0; i < sband->n_channels; i++) {
+		struct ieee80211_channel *ch = &sband->channels[i];
+
+		if (ch->hw_value == chan->hw_value) {
+			if (!(ch->flags & IEEE80211_CHAN_DISABLED)) {
+				int power = 2 * ch->max_reg_power;
+
+				if (is_mt7663(dev) && (power > 63 || power < -64))
+					power = 63;
+				target_power = min_t(s8, power, target_power);
+			}
+			break;
+		}
+	}
+
+	return target_power;
+}
+
 static int
 mt76_connac_mcu_rate_txpower_band(struct mt76_phy *phy,
 				  enum nl80211_band band)
@@ -1816,9 +1871,14 @@
 				.hw_value = ch_list[idx],
 				.band = band,
 			};
+			s8 reg_power, sar_power;
+
+			reg_power = mt76_connac_get_ch_power(phy, &chan,
+							     tx_power);
+			sar_power = mt76_get_sar_power(phy, &chan, reg_power);
 
 			mt76_get_rate_power_limits(phy, &chan, &limits,
-						   tx_power);
+						   sar_power);
 
 			tx_power_tlv.last_msg = ch_list[idx] == last_ch;
 			sku_tlbv.channel = ch_list[idx];
@@ -1929,19 +1989,22 @@
 	    key->cipher != WLAN_CIPHER_SUITE_TKIP)
 		return;
 
-	if (key->cipher == WLAN_CIPHER_SUITE_TKIP) {
-		gtk_tlv->proto = cpu_to_le32(NL80211_WPA_VERSION_1);
+	if (key->cipher == WLAN_CIPHER_SUITE_TKIP)
 		cipher = BIT(3);
-	} else {
-		gtk_tlv->proto = cpu_to_le32(NL80211_WPA_VERSION_2);
+	else
 		cipher = BIT(4);
-	}
 
 	/* we are assuming here to have a single pairwise key */
 	if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) {
+		if (key->cipher == WLAN_CIPHER_SUITE_TKIP)
+			gtk_tlv->proto = cpu_to_le32(NL80211_WPA_VERSION_1);
+		else
+			gtk_tlv->proto = cpu_to_le32(NL80211_WPA_VERSION_2);
+
 		gtk_tlv->pairwise_cipher = cpu_to_le32(cipher);
-		gtk_tlv->group_cipher = cpu_to_le32(cipher);
 		gtk_tlv->keyid = key->keyidx;
+	} else {
+		gtk_tlv->group_cipher = cpu_to_le32(cipher);
 	}
 }
 
@@ -1966,7 +2029,7 @@
 		return -ENOMEM;
 
 	skb_put_data(skb, &hdr, sizeof(hdr));
-	gtk_tlv = (struct mt76_connac_gtk_rekey_tlv *)skb_put(skb,
+	gtk_tlv = (struct mt76_connac_gtk_rekey_tlv *)skb_put_zero(skb,
 							 sizeof(*gtk_tlv));
 	gtk_tlv->tag = cpu_to_le16(UNI_OFFLOAD_OFFLOAD_GTK_REKEY);
 	gtk_tlv->len = cpu_to_le16(sizeof(*gtk_tlv));
@@ -2088,7 +2151,7 @@
 		return -ENOMEM;
 
 	skb_put_data(skb, &hdr, sizeof(hdr));
-	ptlv = (struct mt76_connac_wow_pattern_tlv *)skb_put(skb, sizeof(*ptlv));
+	ptlv = (struct mt76_connac_wow_pattern_tlv *)skb_put_zero(skb, sizeof(*ptlv));
 	ptlv->tag = cpu_to_le16(UNI_SUSPEND_WOW_PATTERN);
 	ptlv->len = cpu_to_le16(sizeof(*ptlv));
 	ptlv->data_len = pattern->pattern_len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76_connac_mcu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76_connac_mcu.h
@@ -124,6 +124,8 @@
 	u8 rsv[1];
 } __packed;
 
+#define RA_LEGACY_OFDM GENMASK(13, 6)
+#define RA_LEGACY_CCK  GENMASK(3, 0)
 #define HT_MCS_MASK_NUM 10
 struct sta_rec_ra_info {
 	__le16 tag;
@@ -554,7 +556,7 @@
 	MCU_CMD_SET_BSS_CONNECTED = MCU_CE_PREFIX | 0x16,
 	MCU_CMD_SET_BSS_ABORT = MCU_CE_PREFIX | 0x17,
 	MCU_CMD_CANCEL_HW_SCAN = MCU_CE_PREFIX | 0x1b,
-	MCU_CMD_SET_ROC = MCU_CE_PREFIX | 0x1d,
+	MCU_CMD_SET_ROC = MCU_CE_PREFIX | 0x1c,
 	MCU_CMD_SET_P2P_OPPPS = MCU_CE_PREFIX | 0x33,
 	MCU_CMD_SET_RATE_TX_POWER = MCU_CE_PREFIX | 0x5d,
 	MCU_CMD_SCHED_SCAN_ENABLE = MCU_CE_PREFIX | 0x61,
@@ -844,14 +846,14 @@
 			* 2: rekey update
 			*/
 	u8 keyid;
-	u8 pad[2];
+	u8 option; /* 1: rekey data update without enabling offload */
+	u8 pad[1];
 	__le32 proto; /* WPA-RSN-WAPI-OPSN */
 	__le32 pairwise_cipher;
 	__le32 group_cipher;
 	__le32 key_mgmt; /* NONE-PSK-IEEE802.1X */
 	__le32 mgmt_group_cipher;
-	u8 option; /* 1: rekey data update without enabling offload */
-	u8 reserverd[3];
+	u8 reserverd[4];
 } __packed;
 
 #define MT76_CONNAC_WOW_MASK_MAX_LEN			16
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x02_eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x02_eeprom.c
@@ -131,15 +131,8 @@
 			s8 *lna_2g, s8 *lna_5g,
 			struct ieee80211_channel *chan)
 {
-	u16 val;
 	u8 lna;
 
-	val = mt76x02_eeprom_get(dev, MT_EE_NIC_CONF_1);
-	if (val & MT_EE_NIC_CONF_1_LNA_EXT_2G)
-		*lna_2g = 0;
-	if (val & MT_EE_NIC_CONF_1_LNA_EXT_5G)
-		memset(lna_5g, 0, sizeof(s8) * 3);
-
 	if (chan->band == NL80211_BAND_2GHZ)
 		lna = *lna_2g;
 	else if (chan->hw_value <= 64)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
@@ -176,7 +176,7 @@
 		mt76_wr(dev, MT_WCID_DROP(idx), (val & ~bit) | (bit * drop));
 }
 
-static __le16
+static u16
 mt76x02_mac_tx_rate_val(struct mt76x02_dev *dev,
 			const struct ieee80211_tx_rate *rate, u8 *nss_val)
 {
@@ -222,14 +222,14 @@
 		rateval |= MT_RXWI_RATE_SGI;
 
 	*nss_val = nss;
-	return cpu_to_le16(rateval);
+	return rateval;
 }
 
 void mt76x02_mac_wcid_set_rate(struct mt76x02_dev *dev, struct mt76_wcid *wcid,
 			       const struct ieee80211_tx_rate *rate)
 {
 	s8 max_txpwr_adj = mt76x02_tx_get_max_txpwr_adj(dev, rate);
-	__le16 rateval;
+	u16 rateval;
 	u32 tx_info;
 	s8 nss;
 
@@ -342,7 +342,7 @@
 	struct ieee80211_key_conf *key = info->control.hw_key;
 	u32 wcid_tx_info;
 	u16 rate_ht_mask = FIELD_PREP(MT_RXWI_RATE_PHY, BIT(1) | BIT(2));
-	u16 txwi_flags = 0;
+	u16 txwi_flags = 0, rateval;
 	u8 nss;
 	s8 txpwr_adj, max_txpwr_adj;
 	u8 ccmp_pn[8], nstreams = dev->mphy.chainmask & 0xf;
@@ -380,14 +380,15 @@
 
 	if (wcid && (rate->idx < 0 || !rate->count)) {
 		wcid_tx_info = wcid->tx_info;
-		txwi->rate = FIELD_GET(MT_WCID_TX_INFO_RATE, wcid_tx_info);
+		rateval = FIELD_GET(MT_WCID_TX_INFO_RATE, wcid_tx_info);
 		max_txpwr_adj = FIELD_GET(MT_WCID_TX_INFO_TXPWR_ADJ,
 					  wcid_tx_info);
 		nss = FIELD_GET(MT_WCID_TX_INFO_NSS, wcid_tx_info);
 	} else {
-		txwi->rate = mt76x02_mac_tx_rate_val(dev, rate, &nss);
+		rateval = mt76x02_mac_tx_rate_val(dev, rate, &nss);
 		max_txpwr_adj = mt76x02_tx_get_max_txpwr_adj(dev, rate);
 	}
+	txwi->rate = cpu_to_le16(rateval);
 
 	txpwr_adj = mt76x02_tx_get_txpwr_adj(dev, dev->txpower_conf,
 					     max_txpwr_adj);
@@ -630,8 +631,11 @@
 
 	mt76_tx_status_unlock(mdev, &list);
 
-	if (!status.skb)
+	if (!status.skb) {
+		spin_lock_bh(&dev->mt76.rx_lock);
 		ieee80211_tx_status_ext(mt76_hw(dev), &status);
+		spin_unlock_bh(&dev->mt76.rx_lock);
+	}
 
 	if (!len)
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
@@ -59,7 +59,8 @@
 		struct ieee80211_vif *vif = info->control.vif;
 		struct mt76x02_vif *mvif = (struct mt76x02_vif *)vif->drv_priv;
 
-		mt76_tx_queue_skb(dev, q, skb, &mvif->group_wcid, NULL);
+		mt76_tx_queue_skb(dev, q, MT_TXQ_PSD, skb, &mvif->group_wcid,
+				  NULL);
 	}
 	spin_unlock_bh(&q->lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x02_usb_mcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x02_usb_mcu.c
@@ -108,7 +108,7 @@
 	ret = mt76u_bulk_msg(dev, skb->data, skb->len, NULL, 500,
 			     MT_EP_OUT_INBAND_CMD);
 	if (ret)
-		return ret;
+		goto out;
 
 	if (wait_resp)
 		ret = mt76x02u_mcu_wait_resp(dev, seq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
@@ -288,7 +288,8 @@
 	mvif->group_wcid.idx = MT_VIF_WCID(idx);
 	mvif->group_wcid.hw_key_idx = -1;
 	mtxq = (struct mt76_txq *)vif->txq->drv_priv;
-	mtxq->wcid = &mvif->group_wcid;
+	rcu_assign_pointer(dev->mt76.wcid[MT_VIF_WCID(idx)], &mvif->group_wcid);
+	mtxq->wcid = MT_VIF_WCID(idx);
 }
 
 int
@@ -341,6 +342,7 @@
 	struct mt76x02_vif *mvif = (struct mt76x02_vif *)vif->drv_priv;
 
 	dev->mt76.vif_mask &= ~BIT(mvif->idx);
+	rcu_assign_pointer(dev->mt76.wcid[mvif->group_wcid.idx], NULL);
 }
 EXPORT_SYMBOL_GPL(mt76x02_remove_interface);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x2/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x2/eeprom.c
@@ -256,7 +256,8 @@
 	struct ieee80211_channel *chan = dev->mphy.chandef.chan;
 	int channel = chan->hw_value;
 	s8 lna_5g[3], lna_2g;
-	u8 lna;
+	bool use_lna;
+	u8 lna = 0;
 	u16 val;
 
 	if (chan->band == NL80211_BAND_2GHZ)
@@ -275,7 +276,15 @@
 	dev->cal.rx.mcu_gain |= (lna_5g[1] & 0xff) << 16;
 	dev->cal.rx.mcu_gain |= (lna_5g[2] & 0xff) << 24;
 
-	lna = mt76x02_get_lna_gain(dev, &lna_2g, lna_5g, chan);
+	val = mt76x02_eeprom_get(dev, MT_EE_NIC_CONF_1);
+	if (chan->band == NL80211_BAND_2GHZ)
+		use_lna = !(val & MT_EE_NIC_CONF_1_LNA_EXT_2G);
+	else
+		use_lna = !(val & MT_EE_NIC_CONF_1_LNA_EXT_5G);
+
+	if (use_lna)
+		lna = mt76x02_get_lna_gain(dev, &lna_2g, lna_5g, chan);
+
 	dev->cal.rx.lna_gain = mt76x02_sign_extend(lna, 8);
 }
 EXPORT_SYMBOL_GPL(mt76x2_read_rx_gain);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
@@ -80,7 +80,7 @@
 	mt76_rmw_field(dev, 0x15a10, 0x1f << 16, 0x9);
 
 	/* RG_SSUSB_G1_CDR_BIC_LTR = 0xf */
-	mt76_rmw_field(dev, 0x15a0c, 0xf << 28, 0xf);
+	mt76_rmw_field(dev, 0x15a0c, 0xfU << 28, 0xf);
 
 	/* RG_SSUSB_CDR_BR_PE1D = 0x3 */
 	mt76_rmw_field(dev, 0x15c58, 0x3 << 6, 0x3);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c
@@ -12,9 +12,9 @@
 {
 	struct mt7915_dev *dev = data;
 
-	if (test_bit(MT76_STATE_RUNNING, &dev->mphy.state))
-		return -EBUSY;
-
+	/* The existing connected stations shall reconnect to apply
+	 * new implicit txbf configuration.
+	 */
 	dev->ibf = !!val;
 
 	return mt7915_mcu_set_txbf(dev, MT_BF_TYPE_UPDATE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/init.c
@@ -130,9 +130,12 @@
 	struct wiphy *wiphy = phy->mt76->hw->wiphy;
 	struct thermal_cooling_device *cdev;
 	struct device *hwmon;
+	const char *name;
 
-	cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
-					       &mt7915_thermal_ops);
+	name = devm_kasprintf(&wiphy->dev, GFP_KERNEL, "mt7915_%s",
+			      wiphy_name(wiphy));
+
+	cdev = thermal_cooling_device_register(name, phy, &mt7915_thermal_ops);
 	if (!IS_ERR(cdev)) {
 		if (sysfs_create_link(&wiphy->dev.kobj, &cdev->device.kobj,
 				      "cooling_device") < 0)
@@ -144,8 +147,7 @@
 	if (!IS_REACHABLE(CONFIG_HWMON))
 		return 0;
 
-	hwmon = devm_hwmon_device_register_with_groups(&wiphy->dev,
-						       wiphy_name(wiphy), phy,
+	hwmon = devm_hwmon_device_register_with_groups(&wiphy->dev, name, phy,
 						       mt7915_hwmon_groups);
 	if (IS_ERR(hwmon))
 		return PTR_ERR(hwmon);
@@ -215,8 +217,8 @@
 	struct wiphy *wiphy = hw->wiphy;
 
 	hw->queues = 4;
-	hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
-	hw->max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
+	hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
+	hw->max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
 	hw->netdev_features = NETIF_F_RXCSUM;
 
 	hw->radiotap_timestamp.units_pos =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
@@ -349,9 +349,16 @@
 	if (rxd2 & MT_RXD2_NORMAL_AMSDU_ERR)
 		return -EINVAL;
 
+	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
+	if (hdr_trans && (rxd1 & MT_RXD1_NORMAL_CM))
+		return -EINVAL;
+
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd1 & MT_RXD1_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	unicast = FIELD_GET(MT_RXD3_NORMAL_ADDR_TYPE, rxd3) == MT_RXD3_NORMAL_U2M;
 	idx = FIELD_GET(MT_RXD1_NORMAL_WLAN_IDX, rxd1);
-	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
 	status->wcid = mt7915_rx_get_wcid(dev, idx, unicast);
 
 	if (status->wcid) {
@@ -792,6 +799,7 @@
 
 	u8 tid = skb->priority & IEEE80211_QOS_CTL_TID_MASK;
 	u8 fc_type, fc_stype;
+	u16 ethertype;
 	bool wmm = false;
 	u32 val;
 
@@ -805,7 +813,8 @@
 	val = FIELD_PREP(MT_TXD1_HDR_FORMAT, MT_HDR_FORMAT_802_3) |
 	      FIELD_PREP(MT_TXD1_TID, tid);
 
-	if (be16_to_cpu(skb->protocol) >= ETH_P_802_3_MIN)
+	ethertype = get_unaligned_be16(&skb->data[12]);
+	if (ethertype >= ETH_P_802_3_MIN)
 		val |= MT_TXD1_ETH_802_3;
 
 	txwi[1] |= cpu_to_le32(val);
@@ -892,6 +901,7 @@
 		val = MT_TXD3_SN_VALID |
 		      FIELD_PREP(MT_TXD3_SEQ, IEEE80211_SEQ_TO_SN(seqno));
 		txwi[3] |= cpu_to_le32(val);
+		txwi[7] &= ~cpu_to_le32(MT_TXD7_HW_AMSDU);
 	}
 
 	val = FIELD_PREP(MT_TXD7_TYPE, fc_type) |
@@ -1232,7 +1242,7 @@
 		goto out;
 
 	info = IEEE80211_SKB_CB(skb);
-	if (!(txs_data[0] & le32_to_cpu(MT_TXS0_ACK_ERROR_MASK)))
+	if (!(txs_data[0] & cpu_to_le32(MT_TXS0_ACK_ERROR_MASK)))
 		info->flags |= IEEE80211_TX_STAT_ACK;
 
 	info->status.ampdu_len = 1;
@@ -1643,13 +1653,15 @@
 		set_bit(MT76_RESET, &phy2->mt76->state);
 		cancel_delayed_work_sync(&phy2->mt76->mac_work);
 	}
+
+	mutex_lock(&dev->mt76.mutex);
+
 	mt76_worker_disable(&dev->mt76.tx_worker);
 	napi_disable(&dev->mt76.napi[0]);
 	napi_disable(&dev->mt76.napi[1]);
 	napi_disable(&dev->mt76.napi[2]);
 	napi_disable(&dev->mt76.tx_napi);
 
-	mutex_lock(&dev->mt76.mutex);
 
 	mt76_wr(dev, MT_MCU_INT_EVENT, MT_MCU_INT_EVENT_DMA_STOPPED);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/mac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/mac.h
@@ -272,7 +272,8 @@
 #define MT_TX_RATE_MODE			GENMASK(9, 6)
 #define MT_TX_RATE_SU_EXT_TONE		BIT(5)
 #define MT_TX_RATE_DCM			BIT(4)
-#define MT_TX_RATE_IDX			GENMASK(3, 0)
+/* VHT/HE only use bits 0-3 */
+#define MT_TX_RATE_IDX			GENMASK(5, 0)
 
 #define MT_TXP_MAX_BUF_NUM		6
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/main.c
@@ -243,7 +243,7 @@
 	rcu_assign_pointer(dev->mt76.wcid[idx], &mvif->sta.wcid);
 	if (vif->txq) {
 		mtxq = (struct mt76_txq *)vif->txq->drv_priv;
-		mtxq->wcid = &mvif->sta.wcid;
+		mtxq->wcid = idx;
 	}
 
 	if (vif->type != NL80211_IFTYPE_AP &&
@@ -302,7 +302,8 @@
 	if (hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
 		return;
 
-	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR))
+	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR) &&
+	    !(mphy->chandef.chan->flags & IEEE80211_CHAN_RADAR))
 		return;
 
 	if (mphy->chandef.chan->center_freq == chandef->chan->center_freq &&
@@ -440,7 +441,8 @@
 		ieee80211_wake_queues(hw);
 	}
 
-	if (changed & IEEE80211_CONF_CHANGE_POWER) {
+	if (changed & (IEEE80211_CONF_CHANGE_POWER |
+		       IEEE80211_CONF_CHANGE_CHANNEL)) {
 		ret = mt7915_mcu_set_txpower_sku(phy);
 		if (ret)
 			return ret;
@@ -524,8 +526,7 @@
 
 	MT76_FILTER(CONTROL, MT_WF_RFCR_DROP_CTS |
 			     MT_WF_RFCR_DROP_RTS |
-			     MT_WF_RFCR_DROP_CTL_RSV |
-			     MT_WF_RFCR_DROP_NDPA);
+			     MT_WF_RFCR_DROP_CTL_RSV);
 
 	*total_flags = flags;
 	mt76_wr(dev, MT_WF_RFCR(band), phy->rxfilter);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
@@ -176,7 +176,7 @@
 		if (ht_cap->ht_supported)
 			mode |= PHY_MODE_GN;
 
-		if (he_cap->has_he)
+		if (he_cap && he_cap->has_he)
 			mode |= PHY_MODE_AX_24G;
 	} else if (band == NL80211_BAND_5GHZ) {
 		mode |= PHY_MODE_A;
@@ -187,7 +187,7 @@
 		if (vht_cap->vht_supported)
 			mode |= PHY_MODE_AC;
 
-		if (he_cap->has_he)
+		if (he_cap && he_cap->has_he)
 			mode |= PHY_MODE_AX_5G;
 	}
 
@@ -721,7 +721,7 @@
 		.bss_idx = mvif->idx,
 		.wlan_idx_lo = msta ? to_wcid_lo(msta->wcid.idx) : 0,
 		.wlan_idx_hi = msta ? to_wcid_hi(msta->wcid.idx) : 0,
-		.muar_idx = msta ? mvif->omac_idx : 0,
+		.muar_idx = msta && msta->wcid.sta ? mvif->omac_idx : 0xe,
 		.is_tlv_append = 1,
 	};
 	struct sk_buff *skb;
@@ -757,7 +757,7 @@
 	}
 
 	if (sta_hdr)
-		sta_hdr->len = cpu_to_le16(sizeof(hdr));
+		le16_add_cpu(&sta_hdr->len, sizeof(hdr));
 
 	return skb_put_data(nskb, &hdr, sizeof(hdr));
 }
@@ -804,7 +804,7 @@
 		.len = cpu_to_le16(sub_len),
 	};
 
-	ptlv = skb_put(skb, sub_len);
+	ptlv = skb_put_zero(skb, sub_len);
 	memcpy(ptlv, &tlv, sizeof(tlv));
 
 	le16_add_cpu(sub_ntlv, 1);
@@ -925,7 +925,7 @@
 
 	elem = ieee80211_bss_get_elem(bss, WLAN_EID_EXT_CAPABILITY);
 
-	if (!elem || elem->datalen < 10 ||
+	if (!elem || elem->datalen <= 10 ||
 	    !(elem->data[10] &
 	      WLAN_EXT_CAPA10_OBSS_NARROW_BW_RU_TOLERANCE_SUPPORT))
 		data->tolerated = false;
@@ -1201,7 +1201,7 @@
 		u8 cipher;
 
 		cipher = mt7915_mcu_get_cipher(key->cipher);
-		if (cipher == MT_CIPHER_NONE)
+		if (cipher == MCU_CIPHER_NONE)
 			return -EOPNOTSUPP;
 
 		sec_key = &sec->key[0];
@@ -1396,8 +1396,11 @@
 	generic = (struct wtbl_generic *)tlv;
 
 	if (sta) {
+		if (vif->type == NL80211_IFTYPE_STATION)
+			generic->partial_aid = cpu_to_le16(vif->bss_conf.aid);
+		else
+			generic->partial_aid = cpu_to_le16(sta->aid);
 		memcpy(generic->peer_addr, sta->addr, ETH_ALEN);
-		generic->partial_aid = cpu_to_le16(sta->aid);
 		generic->muar_idx = mvif->omac_idx;
 		generic->qos = sta->wme;
 	} else {
@@ -1451,12 +1454,15 @@
 	case NL80211_IFTYPE_MESH_POINT:
 	case NL80211_IFTYPE_AP:
 		basic->conn_type = cpu_to_le32(CONNECTION_INFRA_STA);
+		basic->aid = cpu_to_le16(sta->aid);
 		break;
 	case NL80211_IFTYPE_STATION:
 		basic->conn_type = cpu_to_le32(CONNECTION_INFRA_AP);
+		basic->aid = cpu_to_le16(vif->bss_conf.aid);
 		break;
 	case NL80211_IFTYPE_ADHOC:
 		basic->conn_type = cpu_to_le32(CONNECTION_IBSS_ADHOC);
+		basic->aid = cpu_to_le16(sta->aid);
 		break;
 	default:
 		WARN_ON(1);
@@ -1464,7 +1470,6 @@
 	}
 
 	memcpy(basic->peer_addr, sta->addr, ETH_ALEN);
-	basic->aid = cpu_to_le16(sta->aid);
 	basic->qos = sta->wme;
 }
 
@@ -2684,7 +2689,7 @@
 {
 	mt76_wr(dev, MT_TOP_LPCR_HOST_BAND0, MT_TOP_LPCR_HOST_DRV_OWN);
 	if (!mt76_poll_msec(dev, MT_TOP_LPCR_HOST_BAND0,
-			    MT_TOP_LPCR_HOST_FW_OWN, 0, 500)) {
+			    MT_TOP_LPCR_HOST_FW_OWN_STAT, 0, 500)) {
 		dev_err(dev->mt76.dev, "Timeout for driver own\n");
 		return -EIO;
 	}
@@ -2790,7 +2795,7 @@
 	default:
 		ret = -EAGAIN;
 		dev_err(dev->mt76.dev, "Failed to release patch semaphore\n");
-		goto out;
+		break;
 	}
 	release_firmware(fw);
 
@@ -3391,20 +3396,20 @@
 
 static int mt7915_mcu_set_eeprom_flash(struct mt7915_dev *dev)
 {
-#define TOTAL_PAGE_MASK		GENMASK(7, 5)
+#define MAX_PAGE_IDX_MASK	GENMASK(7, 5)
 #define PAGE_IDX_MASK		GENMASK(4, 2)
 #define PER_PAGE_SIZE		0x400
 	struct mt7915_mcu_eeprom req = { .buffer_mode = EE_MODE_BUFFER };
-	u8 total = MT7915_EEPROM_SIZE / PER_PAGE_SIZE;
+	u8 total = DIV_ROUND_UP(MT7915_EEPROM_SIZE, PER_PAGE_SIZE);
 	u8 *eep = (u8 *)dev->mt76.eeprom.data;
 	int eep_len;
 	int i;
 
-	for (i = 0; i <= total; i++, eep += eep_len) {
+	for (i = 0; i < total; i++, eep += eep_len) {
 		struct sk_buff *skb;
 		int ret;
 
-		if (i == total)
+		if (i == total - 1 && !!(MT7915_EEPROM_SIZE % PER_PAGE_SIZE))
 			eep_len = MT7915_EEPROM_SIZE % PER_PAGE_SIZE;
 		else
 			eep_len = PER_PAGE_SIZE;
@@ -3414,7 +3419,7 @@
 		if (!skb)
 			return -ENOMEM;
 
-		req.format = FIELD_PREP(TOTAL_PAGE_MASK, total) |
+		req.format = FIELD_PREP(MAX_PAGE_IDX_MASK, total - 1) |
 			     FIELD_PREP(PAGE_IDX_MASK, i) | EE_FORMAT_WHOLE;
 		req.len = cpu_to_le16(eep_len);
 
@@ -3481,7 +3486,7 @@
 		u8 idx;
 		u8 rsv[4];
 		__le32 len;
-	} req;
+	} req = {};
 	struct sk_buff *skb;
 
 	skb = mt76_mcu_msg_alloc(&dev->mt76, NULL, sizeof(req) + len);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7915/regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7915/regs.h
@@ -426,6 +426,7 @@
 #define MT_TOP_LPCR_HOST_BAND0		MT_TOP(0x10)
 #define MT_TOP_LPCR_HOST_FW_OWN		BIT(0)
 #define MT_TOP_LPCR_HOST_DRV_OWN	BIT(1)
+#define MT_TOP_LPCR_HOST_FW_OWN_STAT	BIT(2)
 
 #define MT_TOP_MISC			MT_TOP(0xf0)
 #define MT_TOP_MISC_FW_STATE		GENMASK(2, 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/Makefile
@@ -5,3 +5,4 @@
 CFLAGS_trace.o := -I$(src)
 
 mt7921e-y := pci.o mac.o mcu.o dma.o eeprom.o main.o init.o debugfs.o trace.o
+mt7921e-$(CONFIG_ACPI) += acpi_sar.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: ISC
+/* Copyright (C) 2022 MediaTek Inc. */
+
+#include <linux/acpi.h>
+#include "mt7921.h"
+
+static int
+mt7921_acpi_read(struct mt7921_dev *dev, u8 *method, u8 **tbl, u32 *len)
+{
+	struct acpi_buffer buf = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *sar_root, *sar_unit;
+	struct mt76_dev *mdev = &dev->mt76;
+	acpi_handle root, handle;
+	acpi_status status;
+	u32 i = 0;
+	int ret;
+
+	root = ACPI_HANDLE(mdev->dev);
+	if (!root)
+		return -EOPNOTSUPP;
+
+	status = acpi_get_handle(root, method, &handle);
+	if (ACPI_FAILURE(status))
+		return -EIO;
+
+	status = acpi_evaluate_object(handle, NULL, NULL, &buf);
+	if (ACPI_FAILURE(status))
+		return -EIO;
+
+	sar_root = buf.pointer;
+	if (sar_root->type != ACPI_TYPE_PACKAGE ||
+	    sar_root->package.count < 4 ||
+	    sar_root->package.elements[0].type != ACPI_TYPE_INTEGER) {
+		dev_err(mdev->dev, "sar cnt = %d\n",
+			sar_root->package.count);
+		ret = -EINVAL;
+		goto free;
+	}
+
+	if (!*tbl) {
+		*tbl = devm_kzalloc(mdev->dev, sar_root->package.count,
+				    GFP_KERNEL);
+		if (!*tbl) {
+			ret = -ENOMEM;
+			goto free;
+		}
+	}
+	if (len)
+		*len = sar_root->package.count;
+
+	for (i = 0; i < sar_root->package.count; i++) {
+		sar_unit = &sar_root->package.elements[i];
+
+		if (sar_unit->type != ACPI_TYPE_INTEGER)
+			break;
+		*(*tbl + i) = (u8)sar_unit->integer.value;
+	}
+	ret = (i == sar_root->package.count) ? 0 : -EINVAL;
+
+free:
+	kfree(sar_root);
+
+	return ret;
+}
+
+/* MTCL : Country List Table for 6G band */
+static int
+mt7921_asar_acpi_read_mtcl(struct mt7921_dev *dev, u8 **table, u8 *version)
+{
+	*version = (mt7921_acpi_read(dev, MT7921_ACPI_MTCL, table, NULL) < 0)
+		   ? 1 : 2;
+	return 0;
+}
+
+/* MTDS : Dynamic SAR Power Table */
+static int
+mt7921_asar_acpi_read_mtds(struct mt7921_dev *dev, u8 **table, u8 version)
+{
+	int len, ret, sarlen, prelen, tblcnt;
+	bool enable;
+
+	ret = mt7921_acpi_read(dev, MT7921_ACPI_MTDS, table, &len);
+	if (ret)
+		return ret;
+
+	/* Table content validation */
+	switch (version) {
+	case 1:
+		enable = ((struct mt7921_asar_dyn *)*table)->enable;
+		sarlen = sizeof(struct mt7921_asar_dyn_limit);
+		prelen = sizeof(struct mt7921_asar_dyn);
+		break;
+	case 2:
+		enable = ((struct mt7921_asar_dyn_v2 *)*table)->enable;
+		sarlen = sizeof(struct mt7921_asar_dyn_limit_v2);
+		prelen = sizeof(struct mt7921_asar_dyn_v2);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	tblcnt = (len - prelen) / sarlen;
+	if (!enable ||
+	    tblcnt > MT7921_ASAR_MAX_DYN || tblcnt < MT7921_ASAR_MIN_DYN)
+		ret = -EINVAL;
+
+	return ret;
+}
+
+/* MTGS : Geo SAR Power Table */
+static int
+mt7921_asar_acpi_read_mtgs(struct mt7921_dev *dev, u8 **table, u8 version)
+{
+	int len, ret = 0, sarlen, prelen, tblcnt;
+
+	ret = mt7921_acpi_read(dev, MT7921_ACPI_MTGS, table, &len);
+	if (ret)
+		return ret;
+
+	/* Table content validation */
+	switch (version) {
+	case 1:
+		sarlen = sizeof(struct mt7921_asar_geo_limit);
+		prelen = sizeof(struct mt7921_asar_geo);
+		break;
+	case 2:
+		sarlen = sizeof(struct mt7921_asar_geo_limit_v2);
+		prelen = sizeof(struct mt7921_asar_geo_v2);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	tblcnt = (len - prelen) / sarlen;
+	if (tblcnt > MT7921_ASAR_MAX_GEO || tblcnt < MT7921_ASAR_MIN_GEO)
+		ret = -EINVAL;
+
+	return ret;
+}
+
+int mt7921_init_acpi_sar(struct mt7921_dev *dev)
+{
+	struct mt7921_acpi_sar *asar;
+	int ret;
+
+	asar = devm_kzalloc(dev->mt76.dev, sizeof(*asar), GFP_KERNEL);
+	if (!asar)
+		return -ENOMEM;
+
+	mt7921_asar_acpi_read_mtcl(dev, (u8 **)&asar->countrylist, &asar->ver);
+
+	/* MTDS is mandatory. Return error if table is invalid */
+	ret = mt7921_asar_acpi_read_mtds(dev, (u8 **)&asar->dyn, asar->ver);
+	if (ret) {
+		devm_kfree(dev->mt76.dev, asar->dyn);
+		devm_kfree(dev->mt76.dev, asar->countrylist);
+		devm_kfree(dev->mt76.dev, asar);
+		return ret;
+	}
+
+	/* MTGS is optional */
+	ret = mt7921_asar_acpi_read_mtgs(dev, (u8 **)&asar->geo, asar->ver);
+	if (ret) {
+		devm_kfree(dev->mt76.dev, asar->geo);
+		asar->geo = NULL;
+	}
+
+	dev->phy.acpisar = asar;
+
+	return 0;
+}
+
+static s8
+mt7921_asar_get_geo_pwr(struct mt7921_phy *phy,
+			enum nl80211_band band, s8 dyn_power)
+{
+	struct mt7921_acpi_sar *asar = phy->acpisar;
+	struct mt7921_asar_geo_band *band_pwr;
+	s8 geo_power;
+	u8 idx, max;
+
+	if (!asar->geo)
+		return dyn_power;
+
+	switch (phy->mt76->dev->region) {
+	case NL80211_DFS_FCC:
+		idx = 0;
+		break;
+	case NL80211_DFS_ETSI:
+		idx = 1;
+		break;
+	default: /* WW */
+		idx = 2;
+		break;
+	}
+
+	if (asar->ver == 1) {
+		band_pwr = &asar->geo->tbl[idx].band[0];
+		max = ARRAY_SIZE(asar->geo->tbl[idx].band);
+	} else {
+		band_pwr = &asar->geo_v2->tbl[idx].band[0];
+		max = ARRAY_SIZE(asar->geo_v2->tbl[idx].band);
+	}
+
+	switch (band) {
+	case NL80211_BAND_2GHZ:
+		idx = 0;
+		break;
+	case NL80211_BAND_5GHZ:
+		idx = 1;
+		break;
+	case NL80211_BAND_6GHZ:
+		idx = 2;
+		break;
+	default:
+		return dyn_power;
+	}
+
+	if (idx >= max)
+		return dyn_power;
+
+	geo_power = (band_pwr + idx)->pwr;
+	dyn_power += (band_pwr + idx)->offset;
+
+	return min(geo_power, dyn_power);
+}
+
+static s8
+mt7921_asar_range_pwr(struct mt7921_phy *phy,
+		      const struct cfg80211_sar_freq_ranges *range,
+		      u8 idx)
+{
+	const struct cfg80211_sar_capa *capa = phy->mt76->hw->wiphy->sar_capa;
+	struct mt7921_acpi_sar *asar = phy->acpisar;
+	u8 *limit, band, max;
+
+	if (!capa)
+		return 127;
+
+	if (asar->ver == 1) {
+		limit = &asar->dyn->tbl[0].frp[0];
+		max = ARRAY_SIZE(asar->dyn->tbl[0].frp);
+	} else {
+		limit = &asar->dyn_v2->tbl[0].frp[0];
+		max = ARRAY_SIZE(asar->dyn_v2->tbl[0].frp);
+	}
+
+	if (idx >= max)
+		return 127;
+
+	if (range->start_freq >= 5945)
+		band = NL80211_BAND_6GHZ;
+	else if (range->start_freq >= 5150)
+		band = NL80211_BAND_5GHZ;
+	else
+		band = NL80211_BAND_2GHZ;
+
+	return mt7921_asar_get_geo_pwr(phy, band, limit[idx]);
+}
+
+int mt7921_init_acpi_sar_power(struct mt7921_phy *phy, bool set_default)
+{
+	const struct cfg80211_sar_capa *capa = phy->mt76->hw->wiphy->sar_capa;
+	int i;
+
+	if (!phy->acpisar)
+		return 0;
+
+	/* When ACPI SAR enabled in HW, we should apply rules for .frp
+	 * 1. w/o .sar_specs : set ACPI SAR power as the defatul value
+	 * 2. w/  .sar_specs : set power with min(.sar_specs, ACPI_SAR)
+	 */
+	for (i = 0; i < capa->num_freq_ranges; i++) {
+		struct mt76_freq_range_power *frp = &phy->mt76->frp[i];
+
+		frp->range = set_default ? &capa->freq_ranges[i] : frp->range;
+		if (!frp->range)
+			continue;
+
+		frp->power = min_t(s8, set_default ? 127 : frp->power,
+				   mt7921_asar_range_pwr(phy, frp->range, i));
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.h
@@ -0,0 +1,93 @@
+/* SPDX-License-Identifier: ISC */
+/* Copyright (C) 2022 MediaTek Inc. */
+
+#ifndef __MT7921_ACPI_SAR_H
+#define __MT7921_ACPI_SAR_H
+
+#define MT7921_ASAR_MIN_DYN		1
+#define MT7921_ASAR_MAX_DYN		8
+#define MT7921_ASAR_MIN_GEO		3
+#define MT7921_ASAR_MAX_GEO		8
+
+#define MT7921_ACPI_MTCL		"MTCL"
+#define MT7921_ACPI_MTDS		"MTDS"
+#define MT7921_ACPI_MTGS		"MTGS"
+
+struct mt7921_asar_dyn_limit {
+	u8 idx;
+	u8 frp[5];
+} __packed;
+
+struct mt7921_asar_dyn {
+	u8 names[4];
+	u8 enable;
+	u8 nr_tbl;
+	struct mt7921_asar_dyn_limit tbl[0];
+} __packed;
+
+struct mt7921_asar_dyn_limit_v2 {
+	u8 idx;
+	u8 frp[11];
+} __packed;
+
+struct mt7921_asar_dyn_v2 {
+	u8 names[4];
+	u8 enable;
+	u8 rsvd;
+	u8 nr_tbl;
+	struct mt7921_asar_dyn_limit_v2 tbl[0];
+} __packed;
+
+struct mt7921_asar_geo_band {
+	u8 pwr;
+	u8 offset;
+} __packed;
+
+struct mt7921_asar_geo_limit {
+	u8 idx;
+	/* 0:2G, 1:5G */
+	struct mt7921_asar_geo_band band[2];
+} __packed;
+
+struct mt7921_asar_geo {
+	u8 names[4];
+	u8 version;
+	u8 nr_tbl;
+	struct mt7921_asar_geo_limit tbl[0];
+} __packed;
+
+struct mt7921_asar_geo_limit_v2 {
+	u8 idx;
+	/* 0:2G, 1:5G, 2:6G */
+	struct mt7921_asar_geo_band band[3];
+} __packed;
+
+struct mt7921_asar_geo_v2 {
+	u8 names[4];
+	u8 version;
+	u8 rsvd;
+	u8 nr_tbl;
+	struct mt7921_asar_geo_limit_v2 tbl[0];
+} __packed;
+
+struct mt7921_asar_cl {
+	u8 names[4];
+	u8 version;
+	u8 mode_6g;
+	u8 cl6g[6];
+} __packed;
+
+struct mt7921_acpi_sar {
+	u8 ver;
+	union {
+		struct mt7921_asar_dyn *dyn;
+		struct mt7921_asar_dyn_v2 *dyn_v2;
+	};
+	union {
+		struct mt7921_asar_geo *geo;
+		struct mt7921_asar_geo_v2 *geo_v2;
+	};
+	struct mt7921_asar_cl *countrylist;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/debugfs.c
@@ -5,6 +5,32 @@
 #include "eeprom.h"
 
 static int
+mt7921_reg_set(void *data, u64 val)
+{
+	struct mt7921_dev *dev = data;
+
+	mt7921_mutex_acquire(dev);
+	mt76_wr(dev, dev->mt76.debugfs_reg, val);
+	mt7921_mutex_release(dev);
+
+	return 0;
+}
+
+static int
+mt7921_reg_get(void *data, u64 *val)
+{
+	struct mt7921_dev *dev = data;
+
+	mt7921_mutex_acquire(dev);
+	*val = mt76_rr(dev, dev->mt76.debugfs_reg);
+	mt7921_mutex_release(dev);
+
+	return 0;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(fops_regval, mt7921_reg_get, mt7921_reg_set,
+			 "0x%08llx\n");
+static int
 mt7921_fw_debug_set(void *data, u64 val)
 {
 	struct mt7921_dev *dev = data;
@@ -69,6 +95,8 @@
 	struct mt7921_dev *dev = file->private;
 	int stat[8], i, n;
 
+	mt7921_mutex_acquire(dev);
+
 	mt7921_ampdu_stat_read_phy(&dev->phy, file);
 
 	/* Tx amsdu info */
@@ -78,6 +106,8 @@
 		n += stat[i];
 	}
 
+	mt7921_mutex_release(dev);
+
 	for (i = 0; i < ARRAY_SIZE(stat); i++) {
 		seq_printf(file, "AMSDU pack count of %d MSDU in TXD: 0x%x ",
 			   i + 1, stat[i]);
@@ -98,25 +128,28 @@
 	struct mt7921_dev *dev = dev_get_drvdata(s->private);
 	int i;
 
-	for (i = 0; i < 16; i++) {
-		int j, acs = i / 4, index = i % 4;
+	mt7921_mutex_acquire(dev);
+
+	for (i = 0; i < 4; i++) {
 		u32 ctrl, val, qlen = 0;
+		int j;
 
-		val = mt76_rr(dev, MT_PLE_AC_QEMPTY(acs, index));
-		ctrl = BIT(31) | BIT(15) | (acs << 8);
+		val = mt76_rr(dev, MT_PLE_AC_QEMPTY(i));
+		ctrl = BIT(31) | BIT(11) | (i << 24);
 
 		for (j = 0; j < 32; j++) {
 			if (val & BIT(j))
 				continue;
 
-			mt76_wr(dev, MT_PLE_FL_Q0_CTRL,
-				ctrl | (j + (index << 5)));
+			mt76_wr(dev, MT_PLE_FL_Q0_CTRL, ctrl | j);
 			qlen += mt76_get_field(dev, MT_PLE_FL_Q3_CTRL,
 					       GENMASK(11, 0));
 		}
-		seq_printf(s, "AC%d%d: queued=%d\n", acs, index, qlen);
+		seq_printf(s, "AC%d: queued=%d\n", i, qlen);
 	}
 
+	mt7921_mutex_release(dev);
+
 	return 0;
 }
 
@@ -229,31 +262,44 @@
 	return 0;
 }
 
+static void
+mt7921_pm_interface_iter(void *priv, u8 *mac, struct ieee80211_vif *vif)
+{
+	struct mt7921_dev *dev = priv;
+
+	mt7921_mcu_set_beacon_filter(dev, vif, dev->pm.enable);
+}
+
 static int
 mt7921_pm_set(void *data, u64 val)
 {
 	struct mt7921_dev *dev = data;
 	struct mt76_connac_pm *pm = &dev->pm;
-	struct mt76_phy *mphy = dev->phy.mt76;
 
-	if (val == pm->enable)
-		return 0;
+	mutex_lock(&dev->mt76.mutex);
 
-	mt7921_mutex_acquire(dev);
+	if (val == pm->enable)
+		goto out;
 
 	if (!pm->enable) {
 		pm->stats.last_wake_event = jiffies;
 		pm->stats.last_doze_event = jiffies;
 	}
-	pm->enable = val;
+	/* make sure the chip is awake here and ps_work is scheduled
+	 * just at end of the this routine.
+	 */
+	pm->enable = false;
+	mt76_connac_pm_wake(&dev->mphy, pm);
 
-	ieee80211_iterate_active_interfaces(mphy->hw,
+	pm->enable = val;
+	ieee80211_iterate_active_interfaces(mt76_hw(dev),
 					    IEEE80211_IFACE_ITER_RESUME_ALL,
-					    mt7921_pm_interface_iter, mphy->priv);
+					    mt7921_pm_interface_iter, dev);
 
 	mt76_connac_mcu_set_deep_sleep(&dev->mt76, pm->ds_enable);
-
-	mt7921_mutex_release(dev);
+	mt76_connac_power_save_sched(&dev->mphy, pm);
+out:
+	mutex_unlock(&dev->mt76.mutex);
 
 	return 0;
 }
@@ -373,7 +419,7 @@
 {
 	struct dentry *dir;
 
-	dir = mt76_register_debugfs(&dev->mt76);
+	dir = mt76_register_debugfs_fops(&dev->mt76, &fops_regval);
 	if (!dir)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/dma.c
@@ -118,111 +118,26 @@
 	mt76_wr(dev, MT_WFDMA0_TX_RING17_EXT_CTRL, PREFETCH(0x380, 0x4));
 }
 
-static u32 __mt7921_reg_addr(struct mt7921_dev *dev, u32 addr)
-{
-	static const struct {
-		u32 phys;
-		u32 mapped;
-		u32 size;
-	} fixed_map[] = {
-		{ 0x00400000, 0x80000, 0x10000}, /* WF_MCU_SYSRAM */
-		{ 0x00410000, 0x90000, 0x10000}, /* WF_MCU_SYSRAM (configure register) */
-		{ 0x40000000, 0x70000, 0x10000}, /* WF_UMAC_SYSRAM */
-		{ 0x54000000, 0x02000, 0x1000 }, /* WFDMA PCIE0 MCU DMA0 */
-		{ 0x55000000, 0x03000, 0x1000 }, /* WFDMA PCIE0 MCU DMA1 */
-		{ 0x58000000, 0x06000, 0x1000 }, /* WFDMA PCIE1 MCU DMA0 (MEM_DMA) */
-		{ 0x59000000, 0x07000, 0x1000 }, /* WFDMA PCIE1 MCU DMA1 */
-		{ 0x7c000000, 0xf0000, 0x10000 }, /* CONN_INFRA */
-		{ 0x7c020000, 0xd0000, 0x10000 }, /* CONN_INFRA, WFDMA */
-		{ 0x7c060000, 0xe0000, 0x10000}, /* CONN_INFRA, conn_host_csr_top */
-		{ 0x80020000, 0xb0000, 0x10000 }, /* WF_TOP_MISC_OFF */
-		{ 0x81020000, 0xc0000, 0x10000 }, /* WF_TOP_MISC_ON */
-		{ 0x820c0000, 0x08000, 0x4000 }, /* WF_UMAC_TOP (PLE) */
-		{ 0x820c8000, 0x0c000, 0x2000 }, /* WF_UMAC_TOP (PSE) */
-		{ 0x820cc000, 0x0e000, 0x2000 }, /* WF_UMAC_TOP (PP) */
-		{ 0x820ce000, 0x21c00, 0x0200 }, /* WF_LMAC_TOP (WF_SEC) */
-		{ 0x820cf000, 0x22000, 0x1000 }, /* WF_LMAC_TOP (WF_PF) */
-		{ 0x820d0000, 0x30000, 0x10000 }, /* WF_LMAC_TOP (WF_WTBLON) */
-		{ 0x820e0000, 0x20000, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_CFG) */
-		{ 0x820e1000, 0x20400, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_TRB) */
-		{ 0x820e2000, 0x20800, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_AGG) */
-		{ 0x820e3000, 0x20c00, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_ARB) */
-		{ 0x820e4000, 0x21000, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_TMAC) */
-		{ 0x820e5000, 0x21400, 0x0800 }, /* WF_LMAC_TOP BN0 (WF_RMAC) */
-		{ 0x820e7000, 0x21e00, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_DMA) */
-		{ 0x820e9000, 0x23400, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_WTBLOFF) */
-		{ 0x820ea000, 0x24000, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_ETBF) */
-		{ 0x820eb000, 0x24200, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_LPON) */
-		{ 0x820ec000, 0x24600, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_INT) */
-		{ 0x820ed000, 0x24800, 0x0800 }, /* WF_LMAC_TOP BN0 (WF_MIB) */
-		{ 0x820f0000, 0xa0000, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_CFG) */
-		{ 0x820f1000, 0xa0600, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_TRB) */
-		{ 0x820f2000, 0xa0800, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_AGG) */
-		{ 0x820f3000, 0xa0c00, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_ARB) */
-		{ 0x820f4000, 0xa1000, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_TMAC) */
-		{ 0x820f5000, 0xa1400, 0x0800 }, /* WF_LMAC_TOP BN1 (WF_RMAC) */
-		{ 0x820f7000, 0xa1e00, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_DMA) */
-		{ 0x820f9000, 0xa3400, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_WTBLOFF) */
-		{ 0x820fa000, 0xa4000, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_ETBF) */
-		{ 0x820fb000, 0xa4200, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_LPON) */
-		{ 0x820fc000, 0xa4600, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_INT) */
-		{ 0x820fd000, 0xa4800, 0x0800 }, /* WF_LMAC_TOP BN1 (WF_MIB) */
-	};
-	int i;
-
-	if (addr < 0x100000)
-		return addr;
-
-	for (i = 0; i < ARRAY_SIZE(fixed_map); i++) {
-		u32 ofs;
-
-		if (addr < fixed_map[i].phys)
-			continue;
-
-		ofs = addr - fixed_map[i].phys;
-		if (ofs > fixed_map[i].size)
-			continue;
-
-		return fixed_map[i].mapped + ofs;
-	}
-
-	if ((addr >= 0x18000000 && addr < 0x18c00000) ||
-	    (addr >= 0x70000000 && addr < 0x78000000) ||
-	    (addr >= 0x7c000000 && addr < 0x7c400000))
-		return mt7921_reg_map_l1(dev, addr);
-
-	dev_err(dev->mt76.dev, "Access currently unsupported address %08x\n",
-		addr);
-
-	return 0;
-}
-
-static u32 mt7921_rr(struct mt76_dev *mdev, u32 offset)
-{
-	struct mt7921_dev *dev = container_of(mdev, struct mt7921_dev, mt76);
-	u32 addr = __mt7921_reg_addr(dev, offset);
-
-	return dev->bus_ops->rr(mdev, addr);
-}
-
-static void mt7921_wr(struct mt76_dev *mdev, u32 offset, u32 val)
+static int mt7921_dma_disable(struct mt7921_dev *dev, bool force)
 {
-	struct mt7921_dev *dev = container_of(mdev, struct mt7921_dev, mt76);
-	u32 addr = __mt7921_reg_addr(dev, offset);
-
-	dev->bus_ops->wr(mdev, addr, val);
-}
+	/* disable WFDMA0 */
+	mt76_clear(dev, MT_WFDMA0_GLO_CFG,
+		   MT_WFDMA0_GLO_CFG_TX_DMA_EN | MT_WFDMA0_GLO_CFG_RX_DMA_EN |
+		   MT_WFDMA0_GLO_CFG_CSR_DISP_BASE_PTR_CHAIN_EN |
+		   MT_WFDMA0_GLO_CFG_OMIT_TX_INFO |
+		   MT_WFDMA0_GLO_CFG_OMIT_RX_INFO |
+		   MT_WFDMA0_GLO_CFG_OMIT_RX_INFO_PFET2);
 
-static u32 mt7921_rmw(struct mt76_dev *mdev, u32 offset, u32 mask, u32 val)
-{
-	struct mt7921_dev *dev = container_of(mdev, struct mt7921_dev, mt76);
-	u32 addr = __mt7921_reg_addr(dev, offset);
+	if (!mt76_poll_msec_tick(dev, MT_WFDMA0_GLO_CFG,
+				 MT_WFDMA0_GLO_CFG_TX_DMA_BUSY |
+				 MT_WFDMA0_GLO_CFG_RX_DMA_BUSY, 0, 100, 1))
+		return -ETIMEDOUT;
 
-	return dev->bus_ops->rmw(mdev, addr, mask, val);
-}
+	/* disable dmashdl */
+	mt76_clear(dev, MT_WFDMA0_GLO_CFG_EXT0,
+		   MT_WFDMA0_CSR_TX_DMASHDL_ENABLE);
+	mt76_set(dev, MT_DMASHDL_SW_CONTROL, MT_DMASHDL_DMASHDL_BYPASS);
 
-static int mt7921_dma_disable(struct mt7921_dev *dev, bool force)
-{
 	if (force) {
 		/* reset */
 		mt76_clear(dev, MT_WFDMA0_RST,
@@ -234,24 +149,6 @@
 			 MT_WFDMA0_RST_LOGIC_RST);
 	}
 
-	/* disable dmashdl */
-	mt76_clear(dev, MT_WFDMA0_GLO_CFG_EXT0,
-		   MT_WFDMA0_CSR_TX_DMASHDL_ENABLE);
-	mt76_set(dev, MT_DMASHDL_SW_CONTROL, MT_DMASHDL_DMASHDL_BYPASS);
-
-	/* disable WFDMA0 */
-	mt76_clear(dev, MT_WFDMA0_GLO_CFG,
-		   MT_WFDMA0_GLO_CFG_TX_DMA_EN | MT_WFDMA0_GLO_CFG_RX_DMA_EN |
-		   MT_WFDMA0_GLO_CFG_CSR_DISP_BASE_PTR_CHAIN_EN |
-		   MT_WFDMA0_GLO_CFG_OMIT_TX_INFO |
-		   MT_WFDMA0_GLO_CFG_OMIT_RX_INFO |
-		   MT_WFDMA0_GLO_CFG_OMIT_RX_INFO_PFET2);
-
-	if (!mt76_poll(dev, MT_WFDMA0_GLO_CFG,
-		       MT_WFDMA0_GLO_CFG_TX_DMA_BUSY |
-		       MT_WFDMA0_GLO_CFG_RX_DMA_BUSY, 0, 1000))
-		return -ETIMEDOUT;
-
 	return 0;
 }
 
@@ -380,20 +277,8 @@
 
 int mt7921_dma_init(struct mt7921_dev *dev)
 {
-	struct mt76_bus_ops *bus_ops;
 	int ret;
 
-	dev->bus_ops = dev->mt76.bus;
-	bus_ops = devm_kmemdup(dev->mt76.dev, dev->bus_ops, sizeof(*bus_ops),
-			       GFP_KERNEL);
-	if (!bus_ops)
-		return -ENOMEM;
-
-	bus_ops->rr = mt7921_rr;
-	bus_ops->wr = mt7921_wr;
-	bus_ops->rmw = mt7921_rmw;
-	dev->mt76.bus = bus_ops;
-
 	mt76_dma_attach(&dev->mt76);
 
 	ret = mt7921_dma_disable(dev, true);
@@ -469,6 +354,10 @@
 		   MT_WFDMA0_GLO_CFG_OMIT_RX_INFO |
 		   MT_WFDMA0_GLO_CFG_OMIT_RX_INFO_PFET2);
 
+	mt76_poll_msec_tick(dev, MT_WFDMA0_GLO_CFG,
+			    MT_WFDMA0_GLO_CFG_TX_DMA_BUSY |
+			    MT_WFDMA0_GLO_CFG_RX_DMA_BUSY, 0, 100, 1);
+
 	/* reset */
 	mt76_clear(dev, MT_WFDMA0_RST,
 		   MT_WFDMA0_RST_DMASHDL_ALL_RST |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/eeprom.c
@@ -36,6 +36,7 @@
 	val = get_unaligned_le16(eeprom);
 
 	switch (val) {
+	case 0x7922:
 	case 0x7961:
 		return 0;
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/init.c
@@ -11,6 +11,10 @@
 	{
 		.max = MT7921_MAX_INTERFACES,
 		.types = BIT(NL80211_IFTYPE_STATION)
+	},
+	{
+		.max = 1,
+		.types = BIT(NL80211_IFTYPE_AP)
 	}
 };
 
@@ -30,18 +34,17 @@
 {
 	struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
 	struct mt7921_dev *dev = mt7921_hw_dev(hw);
-	struct mt7921_phy *phy = mt7921_hw_phy(hw);
 
 	memcpy(dev->mt76.alpha2, request->alpha2, sizeof(dev->mt76.alpha2));
 	dev->mt76.region = request->dfs_region;
 
 	mt7921_mutex_acquire(dev);
 	mt76_connac_mcu_set_channel_domain(hw->priv);
-	mt76_connac_mcu_set_rate_txpower(phy->mt76);
+	mt7921_set_tx_sar_pwr(hw, NULL);
 	mt7921_mutex_release(dev);
 }
 
-static void
+static int
 mt7921_init_wiphy(struct ieee80211_hw *hw)
 {
 	struct mt7921_phy *phy = mt7921_hw_phy(hw);
@@ -49,8 +52,8 @@
 	struct wiphy *wiphy = hw->wiphy;
 
 	hw->queues = 4;
-	hw->max_rx_aggregation_subframes = 64;
-	hw->max_tx_aggregation_subframes = 128;
+	hw->max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
+	hw->max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HE;
 	hw->netdev_features = NETIF_F_RXCSUM;
 
 	hw->radiotap_timestamp.units_pos =
@@ -63,7 +66,8 @@
 
 	wiphy->iface_combinations = if_comb;
 	wiphy->flags &= ~WIPHY_FLAG_IBSS_RSN;
-	wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
+	wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
+				 BIT(NL80211_IFTYPE_AP);
 	wiphy->n_iface_combinations = ARRAY_SIZE(if_comb);
 	wiphy->max_scan_ie_len = MT76_CONNAC_SCAN_IE_LEN;
 	wiphy->max_scan_ssids = 4;
@@ -75,10 +79,22 @@
 	wiphy->max_sched_scan_reqs = 1;
 	wiphy->flags |= WIPHY_FLAG_HAS_CHANNEL_SWITCH;
 	wiphy->reg_notifier = mt7921_regd_notifier;
+	wiphy->sar_capa = &mt76_sar_capa;
+
+	phy->mt76->frp = devm_kcalloc(dev->mt76.dev,
+				      wiphy->sar_capa->num_freq_ranges,
+				      sizeof(struct mt76_freq_range_power),
+				      GFP_KERNEL);
+	if (!phy->mt76->frp)
+		return -ENOMEM;
 
 	wiphy->features |= NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR |
 			   NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR;
 	wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_SET_SCAN_DWELL);
+	wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_BEACON_RATE_LEGACY);
+	wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_BEACON_RATE_HT);
+	wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_BEACON_RATE_VHT);
+	wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_BEACON_RATE_HE);
 
 	ieee80211_hw_set(hw, SINGLE_SCAN_ON_ALL_BANDS);
 	ieee80211_hw_set(hw, HAS_RATE_CONTROL);
@@ -92,6 +108,8 @@
 		ieee80211_hw_set(hw, CONNECTION_MONITOR);
 
 	hw->max_tx_fragments = 4;
+
+	return 0;
 }
 
 static void
@@ -106,6 +124,10 @@
 	mt76_set(dev, MT_WF_RMAC_MIB_TIME0(band), MT_WF_RMAC_MIB_RXTIME_EN);
 	mt76_set(dev, MT_WF_RMAC_MIB_AIRTIME0(band), MT_WF_RMAC_MIB_RXTIME_EN);
 
+	/* enable MIB tx-rx time reporting */
+	mt76_set(dev, MT_MIB_SCR1(band), MT_MIB_TXDUR_EN);
+	mt76_set(dev, MT_MIB_SCR1(band), MT_MIB_RXDUR_EN);
+
 	mt76_rmw_field(dev, MT_DMA_DCR0(band), MT_DMA_DCR0_MAX_RX_LEN, 1536);
 	/* disable rx rate report by default due to hw issues */
 	mt76_clear(dev, MT_DMA_DCR0(band), MT_DMA_DCR0_RXD_G5_EN);
@@ -204,10 +226,16 @@
 	dev->pm.ds_enable = true;
 
 	ret = mt7921_init_hardware(dev);
+
+	mt7921_init_acpi_sar(dev);
+
+	if (ret)
+		return ret;
+
+	ret = mt7921_init_wiphy(hw);
 	if (ret)
 		return ret;
 
-	mt7921_init_wiphy(hw);
 	dev->mphy.sband_2g.sband.ht_cap.cap |=
 			IEEE80211_HT_CAP_LDPC_CODING |
 			IEEE80211_HT_CAP_MAX_AMSDU;
@@ -215,11 +243,15 @@
 			IEEE80211_HT_CAP_LDPC_CODING |
 			IEEE80211_HT_CAP_MAX_AMSDU;
 	dev->mphy.sband_5g.sband.vht_cap.cap |=
-			IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 |
+			IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454 |
 			IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK |
 			IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE |
 			IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE |
 			(3 << IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT);
+	if (is_mt7922(&dev->mt76))
+		dev->mphy.sband_5g.sband.vht_cap.cap |=
+			IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ |
+			IEEE80211_VHT_CAP_SHORT_GI_160;
 
 	dev->mphy.hw->wiphy->available_antennas_rx = dev->mphy.chainmask;
 	dev->mphy.hw->wiphy->available_antennas_tx = dev->mphy.chainmask;
@@ -247,8 +279,17 @@
 
 void mt7921_unregister_device(struct mt7921_dev *dev)
 {
+	int i;
+	struct mt76_connac_pm *pm = &dev->pm;
+
 	mt76_unregister_device(&dev->mt76);
+	mt76_for_each_q_rx(&dev->mt76, i)
+		napi_disable(&dev->mt76.napi[i]);
+	cancel_delayed_work_sync(&pm->ps_work);
+	cancel_work_sync(&pm->wake_work);
+
 	mt7921_tx_token_put(dev);
+	mt7921_mcu_drv_pmctrl(dev);
 	mt7921_dma_cleanup(dev);
 	mt7921_mcu_exit(dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/mac.c
@@ -181,11 +181,55 @@
 }
 
 static void
+mt7921_mac_decode_he_mu_radiotap(struct sk_buff *skb,
+				 struct mt76_rx_status *status,
+				 __le32 *rxv)
+{
+	static const struct ieee80211_radiotap_he_mu mu_known = {
+		.flags1 = HE_BITS(MU_FLAGS1_SIG_B_MCS_KNOWN) |
+			  HE_BITS(MU_FLAGS1_SIG_B_DCM_KNOWN) |
+			  HE_BITS(MU_FLAGS1_CH1_RU_KNOWN) |
+			  HE_BITS(MU_FLAGS1_SIG_B_SYMS_USERS_KNOWN) |
+			  HE_BITS(MU_FLAGS1_SIG_B_COMP_KNOWN),
+		.flags2 = HE_BITS(MU_FLAGS2_BW_FROM_SIG_A_BW_KNOWN) |
+			  HE_BITS(MU_FLAGS2_PUNC_FROM_SIG_A_BW_KNOWN),
+	};
+	struct ieee80211_radiotap_he_mu *he_mu = NULL;
+
+	he_mu = skb_push(skb, sizeof(mu_known));
+	memcpy(he_mu, &mu_known, sizeof(mu_known));
+
+#define MU_PREP(f, v)	le16_encode_bits(v, IEEE80211_RADIOTAP_HE_MU_##f)
+
+	he_mu->flags1 |= MU_PREP(FLAGS1_SIG_B_MCS, status->rate_idx);
+	if (status->he_dcm)
+		he_mu->flags1 |= MU_PREP(FLAGS1_SIG_B_DCM, status->he_dcm);
+
+	he_mu->flags2 |= MU_PREP(FLAGS2_BW_FROM_SIG_A_BW, status->bw) |
+			 MU_PREP(FLAGS2_SIG_B_SYMS_USERS,
+				 le32_get_bits(rxv[2], MT_CRXV_HE_NUM_USER));
+
+	he_mu->ru_ch1[0] = FIELD_GET(MT_CRXV_HE_RU0, cpu_to_le32(rxv[3]));
+
+	if (status->bw >= RATE_INFO_BW_40) {
+		he_mu->flags1 |= HE_BITS(MU_FLAGS1_CH2_RU_KNOWN);
+		he_mu->ru_ch2[0] =
+			FIELD_GET(MT_CRXV_HE_RU1, cpu_to_le32(rxv[3]));
+	}
+
+	if (status->bw >= RATE_INFO_BW_80) {
+		he_mu->ru_ch1[1] =
+			FIELD_GET(MT_CRXV_HE_RU2, cpu_to_le32(rxv[3]));
+		he_mu->ru_ch2[1] =
+			FIELD_GET(MT_CRXV_HE_RU3, cpu_to_le32(rxv[3]));
+	}
+}
+
+static void
 mt7921_mac_decode_he_radiotap(struct sk_buff *skb,
 			      struct mt76_rx_status *status,
 			      __le32 *rxv, u32 phy)
 {
-	/* TODO: struct ieee80211_radiotap_he_mu */
 	static const struct ieee80211_radiotap_he known = {
 		.data1 = HE_BITS(DATA1_DATA_MCS_KNOWN) |
 			 HE_BITS(DATA1_DATA_DCM_KNOWN) |
@@ -193,6 +237,7 @@
 			 HE_BITS(DATA1_CODING_KNOWN) |
 			 HE_BITS(DATA1_LDPC_XSYMSEG_KNOWN) |
 			 HE_BITS(DATA1_DOPPLER_KNOWN) |
+			 HE_BITS(DATA1_SPTL_REUSE_KNOWN) |
 			 HE_BITS(DATA1_BSS_COLOR_KNOWN),
 		.data2 = HE_BITS(DATA2_GI_KNOWN) |
 			 HE_BITS(DATA2_TXBF_KNOWN) |
@@ -207,9 +252,12 @@
 
 	he->data3 = HE_PREP(DATA3_BSS_COLOR, BSS_COLOR, rxv[14]) |
 		    HE_PREP(DATA3_LDPC_XSYMSEG, LDPC_EXT_SYM, rxv[2]);
+	he->data4 = HE_PREP(DATA4_SU_MU_SPTL_REUSE, SR_MASK, rxv[11]);
 	he->data5 = HE_PREP(DATA5_PE_DISAMBIG, PE_DISAMBIG, rxv[2]) |
 		    le16_encode_bits(ltf_size,
 				     IEEE80211_RADIOTAP_HE_DATA5_LTF_SIZE);
+	if (cpu_to_le32(rxv[0]) & MT_PRXV_TXBF)
+		he->data5 |= HE_BITS(DATA5_TXBF);
 	he->data6 = HE_PREP(DATA6_TXOP, TXOP_DUR, rxv[14]) |
 		    HE_PREP(DATA6_DOPPLER, DOPPLER, rxv[14]);
 
@@ -217,8 +265,7 @@
 	case MT_PHY_TYPE_HE_SU:
 		he->data1 |= HE_BITS(DATA1_FORMAT_SU) |
 			     HE_BITS(DATA1_UL_DL_KNOWN) |
-			     HE_BITS(DATA1_BEAM_CHANGE_KNOWN) |
-			     HE_BITS(DATA1_SPTL_REUSE_KNOWN);
+			     HE_BITS(DATA1_BEAM_CHANGE_KNOWN);
 
 		he->data3 |= HE_PREP(DATA3_BEAM_CHANGE, BEAM_CHNG, rxv[14]) |
 			     HE_PREP(DATA3_UL_DL, UPLINK, rxv[2]);
@@ -232,17 +279,15 @@
 		break;
 	case MT_PHY_TYPE_HE_MU:
 		he->data1 |= HE_BITS(DATA1_FORMAT_MU) |
-			     HE_BITS(DATA1_UL_DL_KNOWN) |
-			     HE_BITS(DATA1_SPTL_REUSE_KNOWN);
+			     HE_BITS(DATA1_UL_DL_KNOWN);
 
 		he->data3 |= HE_PREP(DATA3_UL_DL, UPLINK, rxv[2]);
-		he->data4 |= HE_PREP(DATA4_SU_MU_SPTL_REUSE, SR_MASK, rxv[11]);
+		he->data4 |= HE_PREP(DATA4_MU_STA_ID, MU_AID, rxv[7]);
 
 		mt7921_mac_decode_he_radiotap_ru(status, he, rxv);
 		break;
 	case MT_PHY_TYPE_HE_TB:
 		he->data1 |= HE_BITS(DATA1_FORMAT_TRIG) |
-			     HE_BITS(DATA1_SPTL_REUSE_KNOWN) |
 			     HE_BITS(DATA1_SPTL_REUSE2_KNOWN) |
 			     HE_BITS(DATA1_SPTL_REUSE3_KNOWN) |
 			     HE_BITS(DATA1_SPTL_REUSE4_KNOWN);
@@ -338,10 +383,17 @@
 	if (rxd2 & MT_RXD2_NORMAL_AMSDU_ERR)
 		return -EINVAL;
 
+	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
+	if (hdr_trans && (rxd1 & MT_RXD1_NORMAL_CM))
+		return -EINVAL;
+
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd1 & MT_RXD1_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	chfreq = FIELD_GET(MT_RXD3_NORMAL_CH_FREQ, rxd3);
 	unicast = FIELD_GET(MT_RXD3_NORMAL_ADDR_TYPE, rxd3) == MT_RXD3_NORMAL_U2M;
 	idx = FIELD_GET(MT_RXD1_NORMAL_WLAN_IDX, rxd1);
-	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
 	status->wcid = mt7921_rx_get_wcid(dev, idx, unicast);
 
 	if (status->wcid) {
@@ -511,7 +563,7 @@
 			status->nss =
 				FIELD_GET(MT_PRXV_NSTS, v0) + 1;
 			status->encoding = RX_ENC_VHT;
-			if (i > 9)
+			if (i > 11)
 				return -EINVAL;
 			break;
 		case MT_PHY_TYPE_HE_MU:
@@ -606,9 +658,13 @@
 
 	mt7921_mac_assoc_rssi(dev, skb);
 
-	if (rxv && status->flag & RX_FLAG_RADIOTAP_HE)
+	if (rxv && status->flag & RX_FLAG_RADIOTAP_HE) {
 		mt7921_mac_decode_he_radiotap(skb, status, rxv, mode);
 
+		if (status->flag & RX_FLAG_RADIOTAP_HE_MU)
+			mt7921_mac_decode_he_mu_radiotap(skb, status, rxv);
+	}
+
 	if (!status->wcid || !ieee80211_is_data_qos(fc))
 		return 0;
 
@@ -625,6 +681,7 @@
 {
 	u8 tid = skb->priority & IEEE80211_QOS_CTL_TID_MASK;
 	u8 fc_type, fc_stype;
+	u16 ethertype;
 	bool wmm = false;
 	u32 val;
 
@@ -638,7 +695,8 @@
 	val = FIELD_PREP(MT_TXD1_HDR_FORMAT, MT_HDR_FORMAT_802_3) |
 	      FIELD_PREP(MT_TXD1_TID, tid);
 
-	if (be16_to_cpu(skb->protocol) >= ETH_P_802_3_MIN)
+	ethertype = get_unaligned_be16(&skb->data[12]);
+	if (ethertype >= ETH_P_802_3_MIN)
 		val |= MT_TXD1_ETH_802_3;
 
 	txwi[1] |= cpu_to_le32(val);
@@ -735,8 +793,9 @@
 static void mt7921_update_txs(struct mt76_wcid *wcid, __le32 *txwi)
 {
 	struct mt7921_sta *msta = container_of(wcid, struct mt7921_sta, wcid);
-	u32 pid, frame_type = FIELD_GET(MT_TXD2_FRAME_TYPE, txwi[2]);
+	u32 pid, frame_type;
 
+	frame_type = FIELD_GET(MT_TXD2_FRAME_TYPE, le32_to_cpu(txwi[2]));
 	if (!(frame_type & (IEEE80211_FTYPE_DATA >> 2)))
 		return;
 
@@ -1270,12 +1329,21 @@
 {
 	struct mt7921_vif *mvif = (struct mt7921_vif *)vif->drv_priv;
 	struct mt7921_dev *dev = mvif->phy->dev;
+	struct ieee80211_hw *hw = mt76_hw(dev);
 
 	if (vif->type == NL80211_IFTYPE_STATION)
 		ieee80211_disconnect(vif, true);
 
 	mt76_connac_mcu_uni_add_dev(&dev->mphy, vif, &mvif->sta.wcid, true);
 	mt7921_mcu_set_tx(dev, vif);
+
+	if (vif->type == NL80211_IFTYPE_AP) {
+		mt76_connac_mcu_uni_add_bss(dev->phy.mt76, vif, &mvif->sta.wcid,
+					    true);
+		mt7921_mcu_sta_update(dev, NULL, vif, true,
+				      MT76_STA_INFO_STATE_NONE);
+		mt7921_mcu_uni_add_beacon_offload(dev, hw, vif, true);
+	}
 }
 
 static int
@@ -1417,7 +1485,7 @@
 	mib->rts_retries_cnt += mt76_get_field(dev, MT_MIB_MB_BSDR1(0),
 					       MT_MIB_RTS_FAIL_COUNT_MASK);
 
-	for (i = 0, aggr1 = aggr0 + 4; i < 4; i++) {
+	for (i = 0, aggr1 = aggr0 + 8; i < 4; i++) {
 		u32 val, val2;
 
 		val = mt76_rr(dev, MT_TX_AGG_CNT(0, i));
@@ -1493,6 +1561,14 @@
 	    test_bit(MT76_HW_SCHED_SCANNING, &mphy->state))
 		goto out;
 
+	if (mutex_is_locked(&dev->mt76.mutex))
+		/* if mt76 mutex is held we should not put the device
+		 * to sleep since we are currently accessing device
+		 * register map. We need to wait for the next power_save
+		 * trigger.
+		 */
+		goto out;
+
 	if (time_is_after_jiffies(dev->pm.last_activity + delta)) {
 		delta = dev->pm.last_activity + delta - jiffies;
 		goto out;
@@ -1506,34 +1582,6 @@
 	queue_delayed_work(dev->mt76.wq, &dev->pm.ps_work, delta);
 }
 
-int mt7921_mac_set_beacon_filter(struct mt7921_phy *phy,
-				 struct ieee80211_vif *vif,
-				 bool enable)
-{
-	struct mt7921_dev *dev = phy->dev;
-	bool ext_phy = phy != &dev->phy;
-	int err;
-
-	if (!dev->pm.enable)
-		return -EOPNOTSUPP;
-
-	err = mt7921_mcu_set_bss_pm(dev, vif, enable);
-	if (err)
-		return err;
-
-	if (enable) {
-		vif->driver_flags |= IEEE80211_VIF_BEACON_FILTER;
-		mt76_set(dev, MT_WF_RFCR(ext_phy),
-			 MT_WF_RFCR_DROP_OTHER_BEACON);
-	} else {
-		vif->driver_flags &= ~IEEE80211_VIF_BEACON_FILTER;
-		mt76_clear(dev, MT_WF_RFCR(ext_phy),
-			   MT_WF_RFCR_DROP_OTHER_BEACON);
-	}
-
-	return 0;
-}
-
 void mt7921_coredump_work(struct work_struct *work)
 {
 	struct mt7921_dev *dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/mac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/mac.h
@@ -116,6 +116,7 @@
 #define MT_PRXV_TX_DCM			BIT(4)
 #define MT_PRXV_TX_ER_SU_106T		BIT(5)
 #define MT_PRXV_NSTS			GENMASK(9, 7)
+#define MT_PRXV_TXBF			BIT(10)
 #define MT_PRXV_HT_AD_CODE		BIT(11)
 #define MT_PRXV_FRAME_MODE		GENMASK(14, 12)
 #define MT_PRXV_SGI			GENMASK(16, 15)
@@ -138,8 +139,15 @@
 #define MT_CRXV_HE_LTF_SIZE		GENMASK(18, 17)
 #define MT_CRXV_HE_LDPC_EXT_SYM		BIT(20)
 #define MT_CRXV_HE_PE_DISAMBIG		BIT(23)
+#define MT_CRXV_HE_NUM_USER		GENMASK(30, 24)
 #define MT_CRXV_HE_UPLINK		BIT(31)
 
+#define MT_CRXV_HE_RU0			GENMASK(7, 0)
+#define MT_CRXV_HE_RU1			GENMASK(15, 8)
+#define MT_CRXV_HE_RU2			GENMASK(23, 16)
+#define MT_CRXV_HE_RU3			GENMASK(31, 24)
+#define MT_CRXV_HE_MU_AID		GENMASK(30, 20)
+
 #define MT_CRXV_HE_SR_MASK		GENMASK(11, 8)
 #define MT_CRXV_HE_SR1_MASK		GENMASK(16, 12)
 #define MT_CRXV_HE_SR2_MASK             GENMASK(20, 17)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/main.c
@@ -53,6 +53,7 @@
 
 		switch (i) {
 		case NL80211_IFTYPE_STATION:
+		case NL80211_IFTYPE_AP:
 			break;
 		default:
 			continue;
@@ -86,6 +87,23 @@
 			IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO;
 
 		switch (i) {
+		case NL80211_IFTYPE_AP:
+			he_cap_elem->mac_cap_info[2] |=
+				IEEE80211_HE_MAC_CAP2_BSR;
+			he_cap_elem->mac_cap_info[4] |=
+				IEEE80211_HE_MAC_CAP4_BQR;
+			he_cap_elem->mac_cap_info[5] |=
+				IEEE80211_HE_MAC_CAP5_OM_CTRL_UL_MU_DATA_DIS_RX;
+			he_cap_elem->phy_cap_info[3] |=
+				IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_QPSK |
+				IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_QPSK;
+			he_cap_elem->phy_cap_info[6] |=
+				IEEE80211_HE_PHY_CAP6_PARTIAL_BW_EXT_RANGE |
+				IEEE80211_HE_PHY_CAP6_PPE_THRESHOLD_PRESENT;
+			he_cap_elem->phy_cap_info[9] |=
+				IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU |
+				IEEE80211_HE_PHY_CAP9_RX_1024_QAM_LESS_THAN_242_TONE_RU;
+			break;
 		case NL80211_IFTYPE_STATION:
 			he_cap_elem->mac_cap_info[1] |=
 				IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US;
@@ -128,11 +146,23 @@
 				IEEE80211_HE_PHY_CAP9_RX_1024_QAM_LESS_THAN_242_TONE_RU |
 				IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_COMP_SIGB |
 				IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_NON_COMP_SIGB;
+
+			if (is_mt7922(phy->mt76->dev)) {
+				he_cap_elem->phy_cap_info[0] |=
+					IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G;
+				he_cap_elem->phy_cap_info[8] |=
+					IEEE80211_HE_PHY_CAP8_20MHZ_IN_160MHZ_HE_PPDU |
+					IEEE80211_HE_PHY_CAP8_80MHZ_IN_160MHZ_HE_PPDU;
+			}
 			break;
 		}
 
 		he_mcs->rx_mcs_80 = cpu_to_le16(mcs_map);
 		he_mcs->tx_mcs_80 = cpu_to_le16(mcs_map);
+		if (is_mt7922(phy->mt76->dev)) {
+			he_mcs->rx_mcs_160 = cpu_to_le16(mcs_map);
+			he_mcs->tx_mcs_160 = cpu_to_le16(mcs_map);
+		}
 
 		memset(he_cap->ppe_thres, 0, sizeof(he_cap->ppe_thres));
 		if (he_cap_elem->phy_cap_info[6] &
@@ -190,7 +220,7 @@
 	if (err)
 		return err;
 
-	err = mt76_connac_mcu_set_rate_txpower(phy->mt76);
+	err = mt7921_set_tx_sar_pwr(mphy->hw, NULL);
 	if (err)
 		return err;
 
@@ -224,6 +254,7 @@
 
 	cancel_delayed_work_sync(&dev->pm.ps_work);
 	cancel_work_sync(&dev->pm.wake_work);
+	cancel_work_sync(&dev->reset_work);
 	mt76_connac_free_pending_tx_skbs(&dev->pm, NULL);
 
 	mt7921_mutex_acquire(dev);
@@ -282,15 +313,9 @@
 	rcu_assign_pointer(dev->mt76.wcid[idx], &mvif->sta.wcid);
 	if (vif->txq) {
 		mtxq = (struct mt76_txq *)vif->txq->drv_priv;
-		mtxq->wcid = &mvif->sta.wcid;
+		mtxq->wcid = idx;
 	}
 
-	if (vif->type != NL80211_IFTYPE_AP &&
-	    (!mvif->mt76.omac_idx || mvif->mt76.omac_idx > 3))
-		vif->offload_flags = 0;
-
-	vif->offload_flags |= IEEE80211_OFFLOAD_ENCAP_4ADDR;
-
 out:
 	mt7921_mutex_release(dev);
 
@@ -430,7 +455,7 @@
 {
 	struct mt7921_dev *dev = mt7921_hw_dev(hw);
 	struct mt7921_phy *phy = mt7921_hw_phy(hw);
-	int ret;
+	int ret = 0;
 
 	if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
 		ieee80211_stop_queues(hw);
@@ -442,8 +467,11 @@
 
 	mt7921_mutex_acquire(dev);
 
-	if (changed & IEEE80211_CONF_CHANGE_POWER)
-		mt76_connac_mcu_set_rate_txpower(phy->mt76);
+	if (changed & IEEE80211_CONF_CHANGE_POWER) {
+		ret = mt7921_set_tx_sar_pwr(hw, NULL);
+		if (ret)
+			goto out;
+	}
 
 	if (changed & IEEE80211_CONF_CHANGE_MONITOR) {
 		bool enabled = !!(hw->conf.flags & IEEE80211_CONF_MONITOR);
@@ -458,9 +486,10 @@
 		mt76_wr(dev, MT_WF_RFCR(0), phy->rxfilter);
 	}
 
+out:
 	mt7921_mutex_release(dev);
 
-	return 0;
+	return ret;
 }
 
 static int
@@ -533,36 +562,6 @@
 	mt7921_mutex_release(dev);
 }
 
-static int
-mt7921_bss_bcnft_apply(struct mt7921_dev *dev, struct ieee80211_vif *vif,
-		       bool assoc)
-{
-	int ret;
-
-	if (!dev->pm.enable)
-		return 0;
-
-	if (assoc) {
-		ret = mt7921_mcu_uni_bss_bcnft(dev, vif, true);
-		if (ret)
-			return ret;
-
-		vif->driver_flags |= IEEE80211_VIF_BEACON_FILTER;
-		mt76_set(dev, MT_WF_RFCR(0), MT_WF_RFCR_DROP_OTHER_BEACON);
-
-		return 0;
-	}
-
-	ret = mt7921_mcu_set_bss_pm(dev, vif, false);
-	if (ret)
-		return ret;
-
-	vif->driver_flags &= ~IEEE80211_VIF_BEACON_FILTER;
-	mt76_clear(dev, MT_WF_RFCR(0), MT_WF_RFCR_DROP_OTHER_BEACON);
-
-	return 0;
-}
-
 static void mt7921_bss_info_changed(struct ieee80211_hw *hw,
 				    struct ieee80211_vif *vif,
 				    struct ieee80211_bss_conf *info,
@@ -582,6 +581,11 @@
 		}
 	}
 
+	if (changed & (BSS_CHANGED_BEACON |
+		       BSS_CHANGED_BEACON_ENABLED))
+		mt7921_mcu_uni_add_beacon_offload(dev, hw, vif,
+						  info->enable_beacon);
+
 	/* ensure that enable txcmd_mode after bss_info */
 	if (changed & (BSS_CHANGED_QOS | BSS_CHANGED_BEACON_ENABLED))
 		mt7921_mcu_set_tx(dev, vif);
@@ -592,7 +596,8 @@
 	if (changed & BSS_CHANGED_ASSOC) {
 		mt7921_mcu_sta_update(dev, NULL, vif, true,
 				      MT76_STA_INFO_STATE_ASSOC);
-		mt7921_bss_bcnft_apply(dev, vif, info->assoc);
+		if (dev->pm.enable)
+			mt7921_mcu_set_beacon_filter(dev, vif, info->assoc);
 	}
 
 	if (changed & BSS_CHANGED_ARP_FILTER) {
@@ -661,6 +666,7 @@
 
 	mt7921_mac_wtbl_update(dev, msta->wcid.idx,
 			       MT_WTBL_UPDATE_ADM_COUNT_CLEAR);
+	memset(msta->airtime_ac, 0, sizeof(msta->airtime_ac));
 
 	mt7921_mcu_sta_update(dev, sta, vif, true, MT76_STA_INFO_STATE_ASSOC);
 
@@ -1027,7 +1033,7 @@
 		return -EINVAL;
 
 	if ((BIT(hweight8(tx_ant)) - 1) != tx_ant)
-		tx_ant = BIT(ffs(tx_ant) - 1) - 1;
+		return -EINVAL;
 
 	mt7921_mutex_acquire(dev);
 
@@ -1172,6 +1178,88 @@
 					     MCU_UNI_CMD_STA_REC_UPDATE);
 }
 
+int mt7921_set_tx_sar_pwr(struct ieee80211_hw *hw,
+			  const struct cfg80211_sar_specs *sar)
+{
+	struct mt76_phy *mphy = hw->priv;
+	int err;
+
+	if (sar) {
+		err = mt76_init_sar_power(hw, sar);
+		if (err)
+			return err;
+	}
+
+	mt7921_init_acpi_sar_power(mt7921_hw_phy(hw), !sar);
+
+	err = mt76_connac_mcu_set_rate_txpower(mphy);
+
+	return err;
+}
+
+static int mt7921_set_sar_specs(struct ieee80211_hw *hw,
+				const struct cfg80211_sar_specs *sar)
+{
+	struct mt7921_dev *dev = mt7921_hw_dev(hw);
+	int err;
+
+	mt7921_mutex_acquire(dev);
+	err = mt7921_set_tx_sar_pwr(hw, sar);
+	mt7921_mutex_release(dev);
+
+	return err;
+}
+
+static void
+mt7921_channel_switch_beacon(struct ieee80211_hw *hw,
+			     struct ieee80211_vif *vif,
+			     struct cfg80211_chan_def *chandef)
+{
+	struct mt7921_dev *dev = mt7921_hw_dev(hw);
+
+	mt7921_mutex_acquire(dev);
+	mt7921_mcu_uni_add_beacon_offload(dev, hw, vif, true);
+	mt7921_mutex_release(dev);
+}
+
+static int
+mt7921_start_ap(struct ieee80211_hw *hw,
+		struct ieee80211_vif *vif)
+{
+	struct mt7921_vif *mvif = (struct mt7921_vif *)vif->drv_priv;
+	struct mt7921_phy *phy = mt7921_hw_phy(hw);
+	struct mt7921_dev *dev = mt7921_hw_dev(hw);
+	int err;
+
+	err = mt76_connac_mcu_uni_add_bss(phy->mt76, vif, &mvif->sta.wcid,
+					  true);
+	if (err)
+		return err;
+
+	err = mt7921_mcu_set_bss_pm(dev, vif, true);
+	if (err)
+		return err;
+
+	return mt7921_mcu_sta_update(dev, NULL, vif, true,
+				     MT76_STA_INFO_STATE_NONE);
+}
+
+static void
+mt7921_stop_ap(struct ieee80211_hw *hw,
+	       struct ieee80211_vif *vif)
+{
+	struct mt7921_vif *mvif = (struct mt7921_vif *)vif->drv_priv;
+	struct mt7921_phy *phy = mt7921_hw_phy(hw);
+	struct mt7921_dev *dev = mt7921_hw_dev(hw);
+	int err;
+
+	err = mt7921_mcu_set_bss_pm(dev, vif, false);
+	if (err)
+		return;
+
+	mt76_connac_mcu_uni_add_bss(phy->mt76, vif, &mvif->sta.wcid, false);
+}
+
 const struct ieee80211_ops mt7921_ops = {
 	.tx = mt7921_tx,
 	.start = mt7921_start,
@@ -1182,6 +1270,8 @@
 	.conf_tx = mt7921_conf_tx,
 	.configure_filter = mt7921_configure_filter,
 	.bss_info_changed = mt7921_bss_info_changed,
+	.start_ap = mt7921_start_ap,
+	.stop_ap = mt7921_stop_ap,
 	.sta_state = mt7921_sta_state,
 	.sta_pre_rcu_remove = mt76_sta_pre_rcu_remove,
 	.set_key = mt7921_set_key,
@@ -1190,6 +1280,7 @@
 	.set_rts_threshold = mt7921_set_rts_threshold,
 	.wake_tx_queue = mt76_wake_tx_queue,
 	.release_buffered_frames = mt76_release_buffered_frames,
+	.channel_switch_beacon = mt7921_channel_switch_beacon,
 	.get_txpower = mt76_get_txpower,
 	.get_stats = mt7921_get_stats,
 	.get_tsf = mt7921_get_tsf,
@@ -1210,4 +1301,5 @@
 	.set_rekey_data = mt7921_set_rekey_data,
 #endif /* CONFIG_PM */
 	.flush = mt7921_flush,
+	.set_sar_specs = mt7921_set_sar_specs,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c
@@ -82,9 +82,17 @@
 #define FW_START_OVERRIDE		BIT(0)
 #define FW_START_WORKING_PDA_CR4	BIT(2)
 
+#define PATCH_SEC_NOT_SUPPORT		GENMASK(31, 0)
 #define PATCH_SEC_TYPE_MASK		GENMASK(15, 0)
 #define PATCH_SEC_TYPE_INFO		0x2
 
+#define PATCH_SEC_ENC_TYPE_MASK		GENMASK(31, 24)
+#define PATCH_SEC_ENC_TYPE_PLAIN		0x00
+#define PATCH_SEC_ENC_TYPE_AES			0x01
+#define PATCH_SEC_ENC_TYPE_SCRAMBLE		0x02
+#define PATCH_SEC_ENC_SCRAMBLE_INFO_MASK	GENMASK(15, 0)
+#define PATCH_SEC_ENC_AES_KEY_MASK		GENMASK(7, 0)
+
 #define to_wcid_lo(id)			FIELD_GET(GENMASK(7, 0), (u16)id)
 #define to_wcid_hi(id)			FIELD_GET(GENMASK(9, 8), (u16)id)
 
@@ -157,6 +165,7 @@
 			  struct sk_buff *skb, int seq)
 {
 	struct mt7921_mcu_rxd *rxd;
+	int mcu_cmd = cmd & MCU_CMD_MASK;
 	int ret = 0;
 
 	if (!skb) {
@@ -194,6 +203,9 @@
 		skb_pull(skb, sizeof(*rxd));
 		event = (struct mt7921_mcu_uni_event *)skb->data;
 		ret = le32_to_cpu(event->status);
+		/* skip invalid event */
+		if (mcu_cmd != event->cid)
+			ret = -EAGAIN;
 		break;
 	}
 	case MCU_CMD_REG_READ: {
@@ -316,11 +328,13 @@
 			 struct rate_info *rate, u16 r)
 {
 	struct ieee80211_supported_band *sband;
-	u16 flags = 0;
+	u16 flags = 0, rate_idx;
 	u8 txmode = FIELD_GET(MT_WTBL_RATE_TX_MODE, r);
 	u8 gi = 0;
 	u8 bw = 0;
+	bool cck = false;
 
+	memset(rate, 0, sizeof(*rate));
 	rate->mcs = FIELD_GET(MT_WTBL_RATE_MCS, r);
 	rate->nss = FIELD_GET(MT_WTBL_RATE_NSS, r) + 1;
 
@@ -345,13 +359,18 @@
 
 	switch (txmode) {
 	case MT_PHY_TYPE_CCK:
+		cck = true;
+		fallthrough;
 	case MT_PHY_TYPE_OFDM:
 		if (mphy->chandef.chan->band == NL80211_BAND_5GHZ)
 			sband = &mphy->sband_5g.sband;
 		else
 			sband = &mphy->sband_2g.sband;
 
-		rate->legacy = sband->bitrates[rate->mcs].bitrate;
+		rate_idx = FIELD_GET(MT_TX_RATE_IDX, r);
+		rate_idx = mt76_get_rate(mphy->dev, sband, rate_idx,
+					 cck);
+		rate->legacy = sband->bitrates[rate_idx].bitrate;
 		break;
 	case MT_PHY_TYPE_HT:
 	case MT_PHY_TYPE_HT_GF:
@@ -422,7 +441,8 @@
 	if (mvif->idx != event->bss_idx)
 		return;
 
-	if (!(vif->driver_flags & IEEE80211_VIF_BEACON_FILTER))
+	if (!(vif->driver_flags & IEEE80211_VIF_BEACON_FILTER) ||
+	    vif->type != NL80211_IFTYPE_STATION)
 		return;
 
 	ieee80211_connection_loss(vif);
@@ -532,7 +552,8 @@
 		peer.g8 = !!(sta->vht_cap.cap & IEEE80211_VHT_CAP_SHORT_GI_80);
 		peer.g16 = !!(sta->vht_cap.cap & IEEE80211_VHT_CAP_SHORT_GI_160);
 		mt7921_mcu_tx_rate_parse(mphy->mt76, &peer,
-					 &msta->stats.tx_rate, event->tx_rate);
+					 &msta->stats.tx_rate,
+					 le16_to_cpu(event->tx_rate));
 
 		spin_lock_bh(&dev->sta_poll_lock);
 		break;
@@ -619,7 +640,7 @@
 		u8 cipher;
 
 		cipher = mt7921_mcu_get_cipher(key->cipher);
-		if (cipher == MT_CIPHER_NONE)
+		if (cipher == MCU_CIPHER_NONE)
 			return -EOPNOTSUPP;
 
 		sec_key = &sec->key[0];
@@ -739,6 +760,46 @@
 	return 0;
 }
 
+static u32 mt7921_get_data_mode(struct mt7921_dev *dev, u32 info)
+{
+	u32 mode = DL_MODE_NEED_RSP;
+
+	if (info == PATCH_SEC_NOT_SUPPORT)
+		return mode;
+
+	switch (FIELD_GET(PATCH_SEC_ENC_TYPE_MASK, info)) {
+	case PATCH_SEC_ENC_TYPE_PLAIN:
+		break;
+	case PATCH_SEC_ENC_TYPE_AES:
+		mode |= DL_MODE_ENCRYPT;
+		mode |= FIELD_PREP(DL_MODE_KEY_IDX,
+				(info & PATCH_SEC_ENC_AES_KEY_MASK)) & DL_MODE_KEY_IDX;
+		mode |= DL_MODE_RESET_SEC_IV;
+		break;
+	case PATCH_SEC_ENC_TYPE_SCRAMBLE:
+		mode |= DL_MODE_ENCRYPT;
+		mode |= DL_CONFIG_ENCRY_MODE_SEL;
+		mode |= DL_MODE_RESET_SEC_IV;
+		break;
+	default:
+		dev_err(dev->mt76.dev, "Encryption type not support!\n");
+	}
+
+	return mode;
+}
+
+static char *mt7921_patch_name(struct mt7921_dev *dev)
+{
+	char *ret;
+
+	if (is_mt7922(&dev->mt76))
+		ret = MT7922_ROM_PATCH;
+	else
+		ret = MT7921_ROM_PATCH;
+
+	return ret;
+}
+
 static int mt7921_load_patch(struct mt7921_dev *dev)
 {
 	const struct mt7921_patch_hdr *hdr;
@@ -756,7 +817,7 @@
 		return -EAGAIN;
 	}
 
-	ret = request_firmware(&fw, MT7921_ROM_PATCH, dev->mt76.dev);
+	ret = request_firmware(&fw, mt7921_patch_name(dev), dev->mt76.dev);
 	if (ret)
 		goto out;
 
@@ -774,7 +835,8 @@
 	for (i = 0; i < be32_to_cpu(hdr->desc.n_region); i++) {
 		struct mt7921_patch_sec *sec;
 		const u8 *dl;
-		u32 len, addr;
+		u32 len, addr, mode;
+		u32 sec_info = 0;
 
 		sec = (struct mt7921_patch_sec *)(fw->data + sizeof(*hdr) +
 						  i * sizeof(*sec));
@@ -787,9 +849,11 @@
 		addr = be32_to_cpu(sec->info.addr);
 		len = be32_to_cpu(sec->info.len);
 		dl = fw->data + be32_to_cpu(sec->offs);
+		sec_info = be32_to_cpu(sec->info.sec_key_idx);
+		mode = mt7921_get_data_mode(dev, sec_info);
 
 		ret = mt76_connac_mcu_init_download(&dev->mt76, addr, len,
-						    DL_MODE_NEED_RSP);
+						    mode);
 		if (ret) {
 			dev_err(dev->mt76.dev, "Download request failed\n");
 			goto out;
@@ -815,7 +879,7 @@
 	default:
 		ret = -EAGAIN;
 		dev_err(dev->mt76.dev, "Failed to release patch semaphore\n");
-		goto out;
+		break;
 	}
 	release_firmware(fw);
 
@@ -886,13 +950,25 @@
 	return mt76_connac_mcu_start_firmware(&dev->mt76, override, option);
 }
 
+static char *mt7921_ram_name(struct mt7921_dev *dev)
+{
+	char *ret;
+
+	if (is_mt7922(&dev->mt76))
+		ret = MT7922_FIRMWARE_WM;
+	else
+		ret = MT7921_FIRMWARE_WM;
+
+	return ret;
+}
+
 static int mt7921_load_ram(struct mt7921_dev *dev)
 {
 	const struct mt7921_fw_trailer *hdr;
 	const struct firmware *fw;
 	int ret;
 
-	ret = request_firmware(&fw, MT7921_FIRMWARE_WM, dev->mt76.dev);
+	ret = request_firmware(&fw, mt7921_ram_name(dev), dev->mt76.dev);
 	if (ret)
 		return ret;
 
@@ -1193,8 +1269,9 @@
 				 &ps_req, sizeof(ps_req), true);
 }
 
-int mt7921_mcu_uni_bss_bcnft(struct mt7921_dev *dev, struct ieee80211_vif *vif,
-			     bool enable)
+static int
+mt7921_mcu_uni_bss_bcnft(struct mt7921_dev *dev, struct ieee80211_vif *vif,
+			 bool enable)
 {
 	struct mt7921_vif *mvif = (struct mt7921_vif *)vif->drv_priv;
 	struct {
@@ -1228,8 +1305,9 @@
 				 &bcnft_req, sizeof(bcnft_req), true);
 }
 
-int mt7921_mcu_set_bss_pm(struct mt7921_dev *dev, struct ieee80211_vif *vif,
-			  bool enable)
+int
+mt7921_mcu_set_bss_pm(struct mt7921_dev *dev, struct ieee80211_vif *vif,
+		      bool enable)
 {
 	struct mt7921_vif *mvif = (struct mt7921_vif *)vif->drv_priv;
 	struct {
@@ -1256,9 +1334,6 @@
 	};
 	int err;
 
-	if (vif->type != NL80211_IFTYPE_STATION)
-		return 0;
-
 	err = mt76_mcu_send_msg(&dev->mt76, MCU_CMD_SET_BSS_ABORT, &req_hdr,
 				sizeof(req_hdr), false);
 	if (err < 0 || !enable)
@@ -1292,10 +1367,7 @@
 	return mt76_connac_mcu_sta_cmd(&dev->mphy, &info);
 }
 
-int __mt7921_mcu_drv_pmctrl(struct mt7921_dev *dev)
-{
-	struct mt76_phy *mphy = &dev->mt76.phy;
-	struct mt76_connac_pm *pm = &dev->pm;
+int __mt7921_mcu_drv_check_pmctrl(struct mt7921_dev *dev){
 	int i, err = 0;
 
 	for (i = 0; i < MT7921_DRV_OWN_RETRY_COUNT; i++) {
@@ -1308,9 +1380,21 @@
 	if (i == MT7921_DRV_OWN_RETRY_COUNT) {
 		dev_err(dev->mt76.dev, "driver own failed\n");
 		err = -EIO;
-		goto out;
 	}
 
+	return err;
+}
+
+int __mt7921_mcu_drv_pmctrl(struct mt7921_dev *dev)
+{
+	struct mt76_phy *mphy = &dev->mt76.phy;
+	struct mt76_connac_pm *pm = &dev->pm;
+	int err = 0;
+
+	err = __mt7921_mcu_drv_check_pmctrl(dev);
+	if(err < 0)
+		goto out;
+
 	mt7921_wpdma_reinit_cond(dev);
 	clear_bit(MT76_STATE_PM, &mphy->state);
 
@@ -1378,31 +1462,34 @@
 	return err;
 }
 
-void
-mt7921_pm_interface_iter(void *priv, u8 *mac, struct ieee80211_vif *vif)
+int mt7921_mcu_set_beacon_filter(struct mt7921_dev *dev,
+				 struct ieee80211_vif *vif,
+				 bool enable)
 {
-	struct mt7921_phy *phy = priv;
-	struct mt7921_dev *dev = phy->dev;
 	struct ieee80211_hw *hw = mt76_hw(dev);
-	int ret;
-
-	if (dev->pm.enable)
-		ret = mt7921_mcu_uni_bss_bcnft(dev, vif, true);
-	else
-		ret = mt7921_mcu_set_bss_pm(dev, vif, false);
+	int err;
 
-	if (ret)
-		return;
+	if (enable) {
+		err = mt7921_mcu_uni_bss_bcnft(dev, vif, true);
+		if (err)
+			return err;
 
-	if (dev->pm.enable) {
 		vif->driver_flags |= IEEE80211_VIF_BEACON_FILTER;
 		ieee80211_hw_set(hw, CONNECTION_MONITOR);
 		mt76_set(dev, MT_WF_RFCR(0), MT_WF_RFCR_DROP_OTHER_BEACON);
-	} else {
-		vif->driver_flags &= ~IEEE80211_VIF_BEACON_FILTER;
-		__clear_bit(IEEE80211_HW_CONNECTION_MONITOR, hw->flags);
-		mt76_clear(dev, MT_WF_RFCR(0), MT_WF_RFCR_DROP_OTHER_BEACON);
+
+		return 0;
 	}
+
+	err = mt7921_mcu_set_bss_pm(dev, vif, false);
+	if (err)
+		return err;
+
+	vif->driver_flags &= ~IEEE80211_VIF_BEACON_FILTER;
+	__clear_bit(IEEE80211_HW_CONNECTION_MONITOR, hw->flags);
+	mt76_clear(dev, MT_WF_RFCR(0), MT_WF_RFCR_DROP_OTHER_BEACON);
+
+	return 0;
 }
 
 int mt7921_get_txpwr_info(struct mt7921_dev *dev, struct mt7921_txpwr *txpwr)
@@ -1427,3 +1514,81 @@
 
 	return 0;
 }
+
+int
+mt7921_mcu_uni_add_beacon_offload(struct mt7921_dev *dev,
+				  struct ieee80211_hw *hw,
+				  struct ieee80211_vif *vif,
+				  bool enable)
+{
+	struct mt7921_vif *mvif = (struct mt7921_vif *)vif->drv_priv;
+	struct mt76_wcid *wcid = &dev->mt76.global_wcid;
+	struct ieee80211_mutable_offsets offs;
+	struct {
+		struct req_hdr {
+			u8 bss_idx;
+			u8 pad[3];
+		} __packed hdr;
+		struct bcn_content_tlv {
+			__le16 tag;
+			__le16 len;
+			__le16 tim_ie_pos;
+			__le16 csa_ie_pos;
+			__le16 bcc_ie_pos;
+			/* 0: disable beacon offload
+			 * 1: enable beacon offload
+			 * 2: update probe respond offload
+			 */
+			u8 enable;
+			/* 0: legacy format (TXD + payload)
+			 * 1: only cap field IE
+			 */
+			u8 type;
+			__le16 pkt_len;
+			u8 pkt[512];
+		} __packed beacon_tlv;
+	} req = {
+		.hdr = {
+			.bss_idx = mvif->mt76.idx,
+		},
+		.beacon_tlv = {
+			.tag = cpu_to_le16(UNI_BSS_INFO_BCN_CONTENT),
+			.len = cpu_to_le16(sizeof(struct bcn_content_tlv)),
+			.enable = enable,
+		},
+	};
+	struct sk_buff *skb;
+
+	/* support enable/update process only
+	 * disable flow would be handled in bss stop handler automatically
+	 */
+	if (!enable)
+		return -EOPNOTSUPP;
+
+	skb = ieee80211_beacon_get_template(mt76_hw(dev), vif, &offs);
+	if (!skb)
+		return -EINVAL;
+
+	if (skb->len > 512 - MT_TXD_SIZE) {
+		dev_err(dev->mt76.dev, "beacon size limit exceed\n");
+		dev_kfree_skb(skb);
+		return -EINVAL;
+	}
+
+	mt7921_mac_write_txwi(dev, (__le32 *)(req.beacon_tlv.pkt), skb,
+			      wcid, NULL, true);
+	memcpy(req.beacon_tlv.pkt + MT_TXD_SIZE, skb->data, skb->len);
+	req.beacon_tlv.pkt_len = cpu_to_le16(MT_TXD_SIZE + skb->len);
+	req.beacon_tlv.tim_ie_pos = cpu_to_le16(MT_TXD_SIZE + offs.tim_offset);
+
+	if (offs.cntdwn_counter_offs[0]) {
+		u16 csa_offs;
+
+		csa_offs = MT_TXD_SIZE + offs.cntdwn_counter_offs[0] - 4;
+		req.beacon_tlv.csa_ie_pos = cpu_to_le16(csa_offs);
+	}
+	dev_kfree_skb(skb);
+
+	return mt76_mcu_send_msg(&dev->mt76, MCU_UNI_CMD_BSS_INFO_UPDATE,
+				 &req, sizeof(req), true);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/mcu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/mcu.h
@@ -296,11 +296,11 @@
 struct mt7921_mcu_tx_done_event {
 	u8 pid;
 	u8 status;
-	u16 seq;
+	__le16 seq;
 
 	u8 wlan_idx;
 	u8 tx_cnt;
-	u16 tx_rate;
+	__le16 tx_rate;
 
 	u8 flag;
 	u8 tid;
@@ -312,9 +312,9 @@
 	u8 reason;
 	u8 rsv0[1];
 
-	u32 delay;
-	u32 timestamp;
-	u32 applied_flag;
+	__le32 delay;
+	__le32 timestamp;
+	__le32 applied_flag;
 
 	u8 txs[28];
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/mt7921.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/mt7921.h
@@ -8,6 +8,7 @@
 #include <linux/ktime.h>
 #include "../mt76_connac_mcu.h"
 #include "regs.h"
+#include "acpi_sar.h"
 
 #define MT7921_MAX_INTERFACES		4
 #define MT7921_MAX_WMM_SETS		4
@@ -33,6 +34,9 @@
 #define MT7921_FIRMWARE_WM		"mediatek/WIFI_RAM_CODE_MT7961_1.bin"
 #define MT7921_ROM_PATCH		"mediatek/WIFI_MT7961_patch_mcu_1_2_hdr.bin"
 
+#define MT7922_FIRMWARE_WM		"mediatek/WIFI_RAM_CODE_MT7922_1.bin"
+#define MT7922_ROM_PATCH		"mediatek/WIFI_MT7922_patch_mcu_1_1_hdr.bin"
+
 #define MT7921_EEPROM_SIZE		3584
 #define MT7921_TOKEN_SIZE		8192
 
@@ -145,6 +149,9 @@
 
 	struct sk_buff_head scan_event_list;
 	struct delayed_work scan_work;
+#ifdef CONFIG_ACPI
+	struct mt7921_acpi_sar *acpisar;
+#endif
 };
 
 struct mt7921_dev {
@@ -258,6 +265,8 @@
 int mt7921_wpdma_reinit_cond(struct mt7921_dev *dev);
 void mt7921_dma_cleanup(struct mt7921_dev *dev);
 int mt7921_run_firmware(struct mt7921_dev *dev);
+int mt7921_mcu_set_bss_pm(struct mt7921_dev *dev, struct ieee80211_vif *vif,
+			 bool enable);
 int mt7921_mcu_init(struct mt7921_dev *dev);
 int mt7921_mcu_add_key(struct mt7921_dev *dev, struct ieee80211_vif *vif,
 		       struct mt7921_sta *msta, struct ieee80211_key_conf *key,
@@ -363,6 +372,9 @@
 void mt7921_update_channel(struct mt76_phy *mphy);
 int mt7921_init_debugfs(struct mt7921_dev *dev);
 
+int mt7921_mcu_set_beacon_filter(struct mt7921_dev *dev,
+				 struct ieee80211_vif *vif,
+				 bool enable);
 int mt7921_mcu_uni_tx_ba(struct mt7921_dev *dev,
 			 struct ieee80211_ampdu_params *params,
 			 bool enable);
@@ -371,21 +383,36 @@
 			 bool enable);
 void mt7921_scan_work(struct work_struct *work);
 int mt7921_mcu_uni_bss_ps(struct mt7921_dev *dev, struct ieee80211_vif *vif);
-int mt7921_mcu_uni_bss_bcnft(struct mt7921_dev *dev, struct ieee80211_vif *vif,
-			     bool enable);
-int mt7921_mcu_set_bss_pm(struct mt7921_dev *dev, struct ieee80211_vif *vif,
-			  bool enable);
+int __mt7921_mcu_drv_check_pmctrl(struct mt7921_dev *dev);			  
 int __mt7921_mcu_drv_pmctrl(struct mt7921_dev *dev);
 int mt7921_mcu_drv_pmctrl(struct mt7921_dev *dev);
 int mt7921_mcu_fw_pmctrl(struct mt7921_dev *dev);
 void mt7921_pm_wake_work(struct work_struct *work);
 void mt7921_pm_power_save_work(struct work_struct *work);
 bool mt7921_wait_for_mcu_init(struct mt7921_dev *dev);
-int mt7921_mac_set_beacon_filter(struct mt7921_phy *phy,
-				 struct ieee80211_vif *vif,
-				 bool enable);
-void mt7921_pm_interface_iter(void *priv, u8 *mac, struct ieee80211_vif *vif);
 void mt7921_coredump_work(struct work_struct *work);
 int mt7921_wfsys_reset(struct mt7921_dev *dev);
 int mt7921_get_txpwr_info(struct mt7921_dev *dev, struct mt7921_txpwr *txpwr);
+int mt7921_mcu_uni_add_beacon_offload(struct mt7921_dev *dev,
+				      struct ieee80211_hw *hw,
+				      struct ieee80211_vif *vif,
+				      bool enable);
+#ifdef CONFIG_ACPI
+int mt7921_init_acpi_sar(struct mt7921_dev *dev);
+int mt7921_init_acpi_sar_power(struct mt7921_phy *phy, bool set_default);
+#else
+static inline int
+mt7921_init_acpi_sar(struct mt7921_dev *dev)
+{
+	return 0;
+}
+
+static inline int
+mt7921_init_acpi_sar_power(struct mt7921_phy *phy, bool set_default)
+{
+	return 0;
+}
+#endif
+int mt7921_set_tx_sar_pwr(struct ieee80211_hw *hw,
+			  const struct cfg80211_sar_specs *sar);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/pci.c
@@ -14,9 +14,16 @@
 
 static const struct pci_device_id mt7921_pci_device_table[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_MEDIATEK, 0x7961) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_MEDIATEK, 0x7922) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_MEDIATEK, 0x0608) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_MEDIATEK, 0x0616) },
 	{ },
 };
 
+static bool mt7921_disable_aspm;
+module_param_named(disable_aspm, mt7921_disable_aspm, bool, 0644);
+MODULE_PARM_DESC(disable_aspm, "disable PCI ASPM support");
+
 static void
 mt7921_rx_poll_complete(struct mt76_dev *mdev, enum mt76_rxq_id q)
 {
@@ -88,6 +95,109 @@
 		napi_schedule(&dev->mt76.napi[MT_RXQ_MAIN]);
 }
 
+static u32 __mt7921_reg_addr(struct mt7921_dev *dev, u32 addr)
+{
+	static const struct {
+		u32 phys;
+		u32 mapped;
+		u32 size;
+	} fixed_map[] = {
+		{ 0x00400000, 0x80000, 0x10000}, /* WF_MCU_SYSRAM */
+		{ 0x00410000, 0x90000, 0x10000}, /* WF_MCU_SYSRAM (configure register) */
+		{ 0x40000000, 0x70000, 0x10000}, /* WF_UMAC_SYSRAM */
+		{ 0x54000000, 0x02000, 0x1000 }, /* WFDMA PCIE0 MCU DMA0 */
+		{ 0x55000000, 0x03000, 0x1000 }, /* WFDMA PCIE0 MCU DMA1 */
+		{ 0x58000000, 0x06000, 0x1000 }, /* WFDMA PCIE1 MCU DMA0 (MEM_DMA) */
+		{ 0x59000000, 0x07000, 0x1000 }, /* WFDMA PCIE1 MCU DMA1 */
+		{ 0x7c000000, 0xf0000, 0x10000 }, /* CONN_INFRA */
+		{ 0x7c020000, 0xd0000, 0x10000 }, /* CONN_INFRA, WFDMA */
+		{ 0x7c060000, 0xe0000, 0x10000}, /* CONN_INFRA, conn_host_csr_top */
+		{ 0x80020000, 0xb0000, 0x10000 }, /* WF_TOP_MISC_OFF */
+		{ 0x81020000, 0xc0000, 0x10000 }, /* WF_TOP_MISC_ON */
+		{ 0x820c0000, 0x08000, 0x4000 }, /* WF_UMAC_TOP (PLE) */
+		{ 0x820c8000, 0x0c000, 0x2000 }, /* WF_UMAC_TOP (PSE) */
+		{ 0x820cc000, 0x0e000, 0x2000 }, /* WF_UMAC_TOP (PP) */
+		{ 0x820ce000, 0x21c00, 0x0200 }, /* WF_LMAC_TOP (WF_SEC) */
+		{ 0x820cf000, 0x22000, 0x1000 }, /* WF_LMAC_TOP (WF_PF) */
+		{ 0x820d0000, 0x30000, 0x10000 }, /* WF_LMAC_TOP (WF_WTBLON) */
+		{ 0x820e0000, 0x20000, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_CFG) */
+		{ 0x820e1000, 0x20400, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_TRB) */
+		{ 0x820e2000, 0x20800, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_AGG) */
+		{ 0x820e3000, 0x20c00, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_ARB) */
+		{ 0x820e4000, 0x21000, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_TMAC) */
+		{ 0x820e5000, 0x21400, 0x0800 }, /* WF_LMAC_TOP BN0 (WF_RMAC) */
+		{ 0x820e7000, 0x21e00, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_DMA) */
+		{ 0x820e9000, 0x23400, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_WTBLOFF) */
+		{ 0x820ea000, 0x24000, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_ETBF) */
+		{ 0x820eb000, 0x24200, 0x0400 }, /* WF_LMAC_TOP BN0 (WF_LPON) */
+		{ 0x820ec000, 0x24600, 0x0200 }, /* WF_LMAC_TOP BN0 (WF_INT) */
+		{ 0x820ed000, 0x24800, 0x0800 }, /* WF_LMAC_TOP BN0 (WF_MIB) */
+		{ 0x820f0000, 0xa0000, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_CFG) */
+		{ 0x820f1000, 0xa0600, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_TRB) */
+		{ 0x820f2000, 0xa0800, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_AGG) */
+		{ 0x820f3000, 0xa0c00, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_ARB) */
+		{ 0x820f4000, 0xa1000, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_TMAC) */
+		{ 0x820f5000, 0xa1400, 0x0800 }, /* WF_LMAC_TOP BN1 (WF_RMAC) */
+		{ 0x820f7000, 0xa1e00, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_DMA) */
+		{ 0x820f9000, 0xa3400, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_WTBLOFF) */
+		{ 0x820fa000, 0xa4000, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_ETBF) */
+		{ 0x820fb000, 0xa4200, 0x0400 }, /* WF_LMAC_TOP BN1 (WF_LPON) */
+		{ 0x820fc000, 0xa4600, 0x0200 }, /* WF_LMAC_TOP BN1 (WF_INT) */
+		{ 0x820fd000, 0xa4800, 0x0800 }, /* WF_LMAC_TOP BN1 (WF_MIB) */
+	};
+	int i;
+
+	if (addr < 0x100000)
+		return addr;
+
+	for (i = 0; i < ARRAY_SIZE(fixed_map); i++) {
+		u32 ofs;
+
+		if (addr < fixed_map[i].phys)
+			continue;
+
+		ofs = addr - fixed_map[i].phys;
+		if (ofs > fixed_map[i].size)
+			continue;
+
+		return fixed_map[i].mapped + ofs;
+	}
+
+	if ((addr >= 0x18000000 && addr < 0x18c00000) ||
+	    (addr >= 0x70000000 && addr < 0x78000000) ||
+	    (addr >= 0x7c000000 && addr < 0x7c400000))
+		return mt7921_reg_map_l1(dev, addr);
+
+	dev_err(dev->mt76.dev, "Access currently unsupported address %08x\n",
+		addr);
+
+	return 0;
+}
+
+static u32 mt7921_rr(struct mt76_dev *mdev, u32 offset)
+{
+	struct mt7921_dev *dev = container_of(mdev, struct mt7921_dev, mt76);
+	u32 addr = __mt7921_reg_addr(dev, offset);
+
+	return dev->bus_ops->rr(mdev, addr);
+}
+
+static void mt7921_wr(struct mt76_dev *mdev, u32 offset, u32 val)
+{
+	struct mt7921_dev *dev = container_of(mdev, struct mt7921_dev, mt76);
+	u32 addr = __mt7921_reg_addr(dev, offset);
+
+	dev->bus_ops->wr(mdev, addr, val);
+}
+
+static u32 mt7921_rmw(struct mt76_dev *mdev, u32 offset, u32 mask, u32 val)
+{
+	struct mt7921_dev *dev = container_of(mdev, struct mt7921_dev, mt76);
+	u32 addr = __mt7921_reg_addr(dev, offset);
+
+	return dev->bus_ops->rmw(mdev, addr, mask, val);
+}
+
 static int mt7921_pci_probe(struct pci_dev *pdev,
 			    const struct pci_device_id *id)
 {
@@ -112,7 +222,9 @@
 	};
 	struct mt7921_dev *dev;
 	struct mt76_dev *mdev;
+	struct mt76_bus_ops *bus_ops;
 	int ret;
+	u16 cmd;
 
 	ret = pcim_enable_device(pdev);
 	if (ret)
@@ -122,6 +234,11 @@
 	if (ret)
 		return ret;
 
+	pci_read_config_word(pdev, PCI_COMMAND, &cmd);
+	if (!(cmd & PCI_COMMAND_MEMORY)) {
+		cmd |= PCI_COMMAND_MEMORY;
+		pci_write_config_word(pdev, PCI_COMMAND, cmd);
+	}
 	pci_set_master(pdev);
 
 	ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
@@ -132,7 +249,8 @@
 	if (ret)
 		goto err_free_pci_vec;
 
-	mt76_pci_disable_aspm(pdev);
+	if (mt7921_disable_aspm)
+		mt76_pci_disable_aspm(pdev);
 
 	mdev = mt76_alloc_device(&pdev->dev, sizeof(*dev), &mt7921_ops,
 				 &drv_ops);
@@ -145,6 +263,24 @@
 
 	mt76_mmio_init(&dev->mt76, pcim_iomap_table(pdev)[0]);
 	tasklet_init(&dev->irq_tasklet, mt7921_irq_tasklet, (unsigned long)dev);
+
+	dev->bus_ops = dev->mt76.bus;
+	bus_ops = devm_kmemdup(dev->mt76.dev, dev->bus_ops, sizeof(*bus_ops),
+			       GFP_KERNEL);
+	if (!bus_ops) {
+		ret = -ENOMEM;
+		goto err_free_dev;
+	}
+
+	bus_ops->rr = mt7921_rr;
+	bus_ops->wr = mt7921_wr;
+	bus_ops->rmw = mt7921_rmw;
+	dev->mt76.bus = bus_ops;
+
+	ret = __mt7921_mcu_drv_check_pmctrl(dev);
+	if(ret)
+		goto err_free_dev;
+
 	mdev->rev = (mt7921_l1_rr(dev, MT_HW_CHIPID) << 16) |
 		    (mt7921_l1_rr(dev, MT_HW_REV) & 0xff);
 	dev_err(mdev->dev, "ASIC revision: %04x\n", mdev->rev);
@@ -331,6 +467,8 @@
 MODULE_DEVICE_TABLE(pci, mt7921_pci_device_table);
 MODULE_FIRMWARE(MT7921_FIRMWARE_WM);
 MODULE_FIRMWARE(MT7921_ROM_PATCH);
+MODULE_FIRMWARE(MT7922_FIRMWARE_WM);
+MODULE_FIRMWARE(MT7922_ROM_PATCH);
 MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
 MODULE_AUTHOR("Lorenzo Bianconi <lorenzo@kernel.org>");
 MODULE_LICENSE("Dual BSD/GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/mt7921/regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/mt7921/regs.h
@@ -17,13 +17,12 @@
 #define MT_PLE_BASE			0x8000
 #define MT_PLE(ofs)			(MT_PLE_BASE + (ofs))
 
-#define MT_PLE_FL_Q0_CTRL		MT_PLE(0x1b0)
-#define MT_PLE_FL_Q1_CTRL		MT_PLE(0x1b4)
-#define MT_PLE_FL_Q2_CTRL		MT_PLE(0x1b8)
-#define MT_PLE_FL_Q3_CTRL		MT_PLE(0x1bc)
+#define MT_PLE_FL_Q0_CTRL		MT_PLE(0x3e0)
+#define MT_PLE_FL_Q1_CTRL		MT_PLE(0x3e4)
+#define MT_PLE_FL_Q2_CTRL		MT_PLE(0x3e8)
+#define MT_PLE_FL_Q3_CTRL		MT_PLE(0x3ec)
 
-#define MT_PLE_AC_QEMPTY(ac, n)		MT_PLE(0x300 + 0x10 * (ac) + \
-					       ((n) << 2))
+#define MT_PLE_AC_QEMPTY(_n)		MT_PLE(0x500 + 0x40 * (_n))
 #define MT_PLE_AMSDU_PACK_MSDU_CNT(n)	MT_PLE(0x10e0 + ((n) << 2))
 
 #define MT_MDP_BASE			0xf000
@@ -96,6 +95,10 @@
 #define MT_WF_MIB_BASE(_band)		((_band) ? 0xa4800 : 0x24800)
 #define MT_WF_MIB(_band, ofs)		(MT_WF_MIB_BASE(_band) + (ofs))
 
+#define MT_MIB_SCR1(_band)		MT_WF_MIB(_band, 0x004)
+#define MT_MIB_TXDUR_EN			BIT(8)
+#define MT_MIB_RXDUR_EN			BIT(9)
+
 #define MT_MIB_SDR3(_band)		MT_WF_MIB(_band, 0x698)
 #define MT_MIB_SDR3_FCS_ERR_MASK	GENMASK(31, 16)
 
@@ -108,9 +111,9 @@
 #define MT_MIB_SDR34(_band)		MT_WF_MIB(_band, 0x090)
 #define MT_MIB_MU_BF_TX_CNT		GENMASK(15, 0)
 
-#define MT_MIB_SDR36(_band)		MT_WF_MIB(_band, 0x098)
+#define MT_MIB_SDR36(_band)		MT_WF_MIB(_band, 0x054)
 #define MT_MIB_SDR36_TXTIME_MASK	GENMASK(23, 0)
-#define MT_MIB_SDR37(_band)		MT_WF_MIB(_band, 0x09c)
+#define MT_MIB_SDR37(_band)		MT_WF_MIB(_band, 0x058)
 #define MT_MIB_SDR37_RXTIME_MASK	GENMASK(23, 0)
 
 #define MT_MIB_DR8(_band)		MT_WF_MIB(_band, 0x0c0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/sdio.c
@@ -213,7 +213,7 @@
 	} while (nframes > 0);
 
 	if (resched)
-		mt76_worker_schedule(&dev->sdio.txrx_worker);
+		mt76_worker_schedule(&dev->tx_worker);
 }
 
 static void mt76s_tx_status_data(struct work_struct *work)
@@ -243,8 +243,8 @@
 
 static int
 mt76s_tx_queue_skb(struct mt76_dev *dev, struct mt76_queue *q,
-		   struct sk_buff *skb, struct mt76_wcid *wcid,
-		   struct ieee80211_sta *sta)
+		   enum mt76_txq_id qid, struct sk_buff *skb,
+		   struct mt76_wcid *wcid, struct ieee80211_sta *sta)
 {
 	struct mt76_tx_info tx_info = {
 		.skb = skb,
@@ -256,7 +256,7 @@
 		return -ENOSPC;
 
 	skb->prev = skb->next = NULL;
-	err = dev->drv->tx_prepare_skb(dev, NULL, q->qid, wcid, sta, &tx_info);
+	err = dev->drv->tx_prepare_skb(dev, NULL, qid, wcid, sta, &tx_info);
 	if (err < 0)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/testmode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/testmode.c
@@ -6,6 +6,7 @@
 	[MT76_TM_ATTR_RESET] = { .type = NLA_FLAG },
 	[MT76_TM_ATTR_STATE] = { .type = NLA_U8 },
 	[MT76_TM_ATTR_TX_COUNT] = { .type = NLA_U32 },
+	[MT76_TM_ATTR_TX_LENGTH] = { .type = NLA_U32 },
 	[MT76_TM_ATTR_TX_RATE_MODE] = { .type = NLA_U8 },
 	[MT76_TM_ATTR_TX_RATE_NSS] = { .type = NLA_U8 },
 	[MT76_TM_ATTR_TX_RATE_IDX] = { .type = NLA_U8 },
@@ -48,8 +49,8 @@
 	       q->queued < q->ndesc / 2) {
 		int ret;
 
-		ret = dev->queue_ops->tx_queue_skb(dev, q, skb_get(skb), wcid,
-						   NULL);
+		ret = dev->queue_ops->tx_queue_skb(dev, q, qid, skb_get(skb),
+						   wcid, NULL);
 		if (ret < 0)
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/tx.c
@@ -68,7 +68,9 @@
 			status.sta = wcid_to_sta(wcid);
 
 		hw = mt76_tx_status_get_hw(dev, skb);
+		spin_lock_bh(&dev->rx_lock);
 		ieee80211_tx_status_ext(hw, &status);
+		spin_unlock_bh(&dev->rx_lock);
 	}
 	rcu_read_unlock();
 }
@@ -229,7 +231,9 @@
 	if (!skb->prev) {
 		hw = mt76_tx_status_get_hw(dev, skb);
 		status.sta = wcid_to_sta(wcid);
+		spin_lock_bh(&dev->rx_lock);
 		ieee80211_tx_status_ext(hw, &status);
+		spin_unlock_bh(&dev->rx_lock);
 		goto out;
 	}
 
@@ -255,7 +259,7 @@
 	int idx;
 
 	non_aql = !info->tx_time_est;
-	idx = dev->queue_ops->tx_queue_skb(dev, q, skb, wcid, sta);
+	idx = dev->queue_ops->tx_queue_skb(dev, q, qid, skb, wcid, sta);
 	if (idx < 0 || !sta)
 		return idx;
 
@@ -406,12 +410,11 @@
 
 static int
 mt76_txq_send_burst(struct mt76_phy *phy, struct mt76_queue *q,
-		    struct mt76_txq *mtxq)
+		    struct mt76_txq *mtxq, struct mt76_wcid *wcid)
 {
 	struct mt76_dev *dev = phy->dev;
 	struct ieee80211_txq *txq = mtxq_to_txq(mtxq);
 	enum mt76_txq_id qid = mt76_txq_get_qid(txq);
-	struct mt76_wcid *wcid = mtxq->wcid;
 	struct ieee80211_tx_info *info;
 	struct sk_buff *skb;
 	int n_frames = 1;
@@ -491,8 +494,8 @@
 			break;
 
 		mtxq = (struct mt76_txq *)txq->drv_priv;
-		wcid = mtxq->wcid;
-		if (wcid && test_bit(MT_WCID_FLAG_PS, &wcid->flags))
+		wcid = rcu_dereference(dev->wcid[mtxq->wcid]);
+		if (!wcid || test_bit(MT_WCID_FLAG_PS, &wcid->flags))
 			continue;
 
 		spin_lock_bh(&q->lock);
@@ -511,7 +514,7 @@
 		}
 
 		if (!mt76_txq_stopped(q))
-			n_frames = mt76_txq_send_burst(phy, q, mtxq);
+			n_frames = mt76_txq_send_burst(phy, q, mtxq, wcid);
 
 		spin_unlock_bh(&q->lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/usb.c
@@ -34,9 +34,9 @@
 
 		ret = usb_control_msg(udev, pipe, req, req_type, val,
 				      offset, buf, len, MT_VEND_REQ_TOUT_MS);
-		if (ret == -ENODEV)
+		if (ret == -ENODEV || ret == -EPROTO)
 			set_bit(MT76_REMOVED, &dev->phy.state);
-		if (ret >= 0 || ret == -ENODEV)
+		if (ret >= 0 || ret == -ENODEV || ret == -EPROTO)
 			return ret;
 		usleep_range(5000, 10000);
 	}
@@ -814,6 +814,9 @@
 	struct mt76_queue *q;
 	int i;
 
+	if (!test_bit(MT76_STATE_RUNNING, &dev->phy.state))
+		return;
+
 	for (i = 0; i < IEEE80211_NUM_ACS; i++) {
 		q = dev->phy.q_tx[i];
 		if (!q)
@@ -833,11 +836,11 @@
 			wake_up(&dev->tx_wait);
 
 		mt76_worker_schedule(&dev->tx_worker);
-
-		if (dev->drv->tx_status_data &&
-		    !test_and_set_bit(MT76_READING_STATS, &dev->phy.state))
-			queue_work(dev->wq, &dev->usb.stat_work);
 	}
+
+	if (dev->drv->tx_status_data &&
+	    !test_and_set_bit(MT76_READING_STATS, &dev->phy.state))
+		queue_work(dev->wq, &dev->usb.stat_work);
 }
 
 static void mt76u_tx_status_data(struct work_struct *work)
@@ -898,8 +901,8 @@
 
 static int
 mt76u_tx_queue_skb(struct mt76_dev *dev, struct mt76_queue *q,
-		   struct sk_buff *skb, struct mt76_wcid *wcid,
-		   struct ieee80211_sta *sta)
+		   enum mt76_txq_id qid, struct sk_buff *skb,
+		   struct mt76_wcid *wcid, struct ieee80211_sta *sta)
 {
 	struct mt76_tx_info tx_info = {
 		.skb = skb,
@@ -911,7 +914,7 @@
 		return -ENOSPC;
 
 	skb->prev = skb->next = NULL;
-	err = dev->drv->tx_prepare_skb(dev, NULL, q->qid, wcid, sta, &tx_info);
+	err = dev->drv->tx_prepare_skb(dev, NULL, qid, wcid, sta, &tx_info);
 	if (err < 0)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt76/util.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt76/util.c
@@ -24,23 +24,23 @@
 }
 EXPORT_SYMBOL_GPL(__mt76_poll);
 
-bool __mt76_poll_msec(struct mt76_dev *dev, u32 offset, u32 mask, u32 val,
-		      int timeout)
+bool ____mt76_poll_msec(struct mt76_dev *dev, u32 offset, u32 mask, u32 val,
+			int timeout, int tick)
 {
 	u32 cur;
 
-	timeout /= 10;
+	timeout /= tick;
 	do {
 		cur = __mt76_rr(dev, offset) & mask;
 		if (cur == val)
 			return true;
 
-		usleep_range(10000, 20000);
+		usleep_range(1000 * tick, 2000 * tick);
 	} while (timeout-- > 0);
 
 	return false;
 }
-EXPORT_SYMBOL_GPL(__mt76_poll_msec);
+EXPORT_SYMBOL_GPL(____mt76_poll_msec);
 
 int mt76_wcid_alloc(u32 *mask, int size)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -123,7 +123,8 @@
 	if (data_len < min_seg_len ||
 	    WARN_ON_ONCE(!dma_len) ||
 	    WARN_ON_ONCE(dma_len + MT_DMA_HDRS > data_len) ||
-	    WARN_ON_ONCE(dma_len & 0x3))
+	    WARN_ON_ONCE(dma_len & 0x3) ||
+	    WARN_ON_ONCE(dma_len < min_seg_len))
 		return 0;
 
 	return MT_DMA_HDRS + dma_len;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/cfg80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/cfg80211.c
@@ -129,8 +129,7 @@
 						info->frame_len,
 						(s32)info->rssi * 100,
 						GFP_KERNEL);
-		if (!bss)
-			cfg80211_put_bss(wiphy, bss);
+		cfg80211_put_bss(wiphy, bss);
 	} else if (scan_event == SCAN_EVENT_DONE) {
 		mutex_lock(&priv->scan_req_lock);
 
@@ -940,30 +939,52 @@
 		return;
 
 	while (index + sizeof(*e) <= len) {
+		u16 attr_size;
+
 		e = (struct wilc_attr_entry *)&buf[index];
-		if (e->attr_type == IEEE80211_P2P_ATTR_CHANNEL_LIST)
+		attr_size = le16_to_cpu(e->attr_len);
+
+		if (index + sizeof(*e) + attr_size > len)
+			return;
+
+		if (e->attr_type == IEEE80211_P2P_ATTR_CHANNEL_LIST &&
+		    attr_size >= (sizeof(struct wilc_attr_ch_list) - sizeof(*e)))
 			ch_list_idx = index;
-		else if (e->attr_type == IEEE80211_P2P_ATTR_OPER_CHANNEL)
+		else if (e->attr_type == IEEE80211_P2P_ATTR_OPER_CHANNEL &&
+			 attr_size == (sizeof(struct wilc_attr_oper_ch) - sizeof(*e)))
 			op_ch_idx = index;
+
 		if (ch_list_idx && op_ch_idx)
 			break;
-		index += le16_to_cpu(e->attr_len) + sizeof(*e);
+
+		index += sizeof(*e) + attr_size;
 	}
 
 	if (ch_list_idx) {
-		u16 attr_size;
-		struct wilc_ch_list_elem *e;
-		int i;
+		unsigned int i;
+		u16 elem_size;
 
 		ch_list = (struct wilc_attr_ch_list *)&buf[ch_list_idx];
-		attr_size = le16_to_cpu(ch_list->attr_len);
-		for (i = 0; i < attr_size;) {
+		/* the number of bytes following the final 'elem' member */
+		elem_size = le16_to_cpu(ch_list->attr_len) -
+			(sizeof(*ch_list) - sizeof(struct wilc_attr_entry));
+		for (i = 0; i < elem_size;) {
+			struct wilc_ch_list_elem *e;
+
 			e = (struct wilc_ch_list_elem *)(ch_list->elem + i);
+
+			i += sizeof(*e);
+			if (i > elem_size)
+				break;
+
+			i += e->no_of_channels;
+			if (i > elem_size)
+				break;
+
 			if (e->op_class == WILC_WLAN_OPERATING_CLASS_2_4GHZ) {
 				memset(e->ch_list, sta_ch, e->no_of_channels);
 				break;
 			}
-			i += e->no_of_channels;
 		}
 	}
 
@@ -1541,7 +1562,6 @@
 	cfg80211_unregister_netdevice(vif->ndev);
 	vif->monitor_flag = 0;
 
-	wilc_set_operation_mode(vif, 0, 0, 0);
 	mutex_lock(&wl->vif_mutex);
 	list_del_rcu(&vif->list);
 	wl->vif_num--;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/hif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/hif.c
@@ -359,38 +359,52 @@
 void *wilc_parse_join_bss_param(struct cfg80211_bss *bss,
 				struct cfg80211_crypto_settings *crypto)
 {
-	struct wilc_join_bss_param *param;
+	const u8 *ies_data, *tim_elm, *ssid_elm, *rates_ie, *supp_rates_ie;
+	const u8 *ht_ie, *wpa_ie, *wmm_ie, *rsn_ie;
 	struct ieee80211_p2p_noa_attr noa_attr;
+	const struct cfg80211_bss_ies *ies;
+	struct wilc_join_bss_param *param;
 	u8 rates_len = 0;
-	const u8 *tim_elm, *ssid_elm, *rates_ie, *supp_rates_ie;
-	const u8 *ht_ie, *wpa_ie, *wmm_ie, *rsn_ie;
+	int ies_len;
+	u64 ies_tsf;
 	int ret;
-	const struct cfg80211_bss_ies *ies = rcu_dereference(bss->ies);
 
 	param = kzalloc(sizeof(*param), GFP_KERNEL);
 	if (!param)
 		return NULL;
 
+	rcu_read_lock();
+	ies = rcu_dereference(bss->ies);
+	ies_data = kmemdup(ies->data, ies->len, GFP_ATOMIC);
+	if (!ies_data) {
+		rcu_read_unlock();
+		kfree(param);
+		return NULL;
+	}
+	ies_len = ies->len;
+	ies_tsf = ies->tsf;
+	rcu_read_unlock();
+
 	param->beacon_period = cpu_to_le16(bss->beacon_interval);
 	param->cap_info = cpu_to_le16(bss->capability);
 	param->bss_type = WILC_FW_BSS_TYPE_INFRA;
 	param->ch = ieee80211_frequency_to_channel(bss->channel->center_freq);
 	ether_addr_copy(param->bssid, bss->bssid);
 
-	ssid_elm = cfg80211_find_ie(WLAN_EID_SSID, ies->data, ies->len);
+	ssid_elm = cfg80211_find_ie(WLAN_EID_SSID, ies_data, ies_len);
 	if (ssid_elm) {
 		if (ssid_elm[1] <= IEEE80211_MAX_SSID_LEN)
 			memcpy(param->ssid, ssid_elm + 2, ssid_elm[1]);
 	}
 
-	tim_elm = cfg80211_find_ie(WLAN_EID_TIM, ies->data, ies->len);
+	tim_elm = cfg80211_find_ie(WLAN_EID_TIM, ies_data, ies_len);
 	if (tim_elm && tim_elm[1] >= 2)
 		param->dtim_period = tim_elm[3];
 
 	memset(param->p_suites, 0xFF, 3);
 	memset(param->akm_suites, 0xFF, 3);
 
-	rates_ie = cfg80211_find_ie(WLAN_EID_SUPP_RATES, ies->data, ies->len);
+	rates_ie = cfg80211_find_ie(WLAN_EID_SUPP_RATES, ies_data, ies_len);
 	if (rates_ie) {
 		rates_len = rates_ie[1];
 		if (rates_len > WILC_MAX_RATES_SUPPORTED)
@@ -401,7 +415,7 @@
 
 	if (rates_len < WILC_MAX_RATES_SUPPORTED) {
 		supp_rates_ie = cfg80211_find_ie(WLAN_EID_EXT_SUPP_RATES,
-						 ies->data, ies->len);
+						 ies_data, ies_len);
 		if (supp_rates_ie) {
 			u8 ext_rates = supp_rates_ie[1];
 
@@ -416,15 +430,15 @@
 		}
 	}
 
-	ht_ie = cfg80211_find_ie(WLAN_EID_HT_CAPABILITY, ies->data, ies->len);
+	ht_ie = cfg80211_find_ie(WLAN_EID_HT_CAPABILITY, ies_data, ies_len);
 	if (ht_ie)
 		param->ht_capable = true;
 
-	ret = cfg80211_get_p2p_attr(ies->data, ies->len,
+	ret = cfg80211_get_p2p_attr(ies_data, ies_len,
 				    IEEE80211_P2P_ATTR_ABSENCE_NOTICE,
 				    (u8 *)&noa_attr, sizeof(noa_attr));
 	if (ret > 0) {
-		param->tsf_lo = cpu_to_le32(ies->tsf);
+		param->tsf_lo = cpu_to_le32(ies_tsf);
 		param->noa_enabled = 1;
 		param->idx = noa_attr.index;
 		if (noa_attr.oppps_ctwindow & IEEE80211_P2P_OPPPS_ENABLE_BIT) {
@@ -444,7 +458,7 @@
 	}
 	wmm_ie = cfg80211_find_vendor_ie(WLAN_OUI_MICROSOFT,
 					 WLAN_OUI_TYPE_MICROSOFT_WMM,
-					 ies->data, ies->len);
+					 ies_data, ies_len);
 	if (wmm_ie) {
 		struct ieee80211_wmm_param_ie *ie;
 
@@ -459,22 +473,33 @@
 
 	wpa_ie = cfg80211_find_vendor_ie(WLAN_OUI_MICROSOFT,
 					 WLAN_OUI_TYPE_MICROSOFT_WPA,
-					 ies->data, ies->len);
+					 ies_data, ies_len);
 	if (wpa_ie) {
 		param->mode_802_11i = 1;
 		param->rsn_found = true;
 	}
 
-	rsn_ie = cfg80211_find_ie(WLAN_EID_RSN, ies->data, ies->len);
+	rsn_ie = cfg80211_find_ie(WLAN_EID_RSN, ies_data, ies_len);
 	if (rsn_ie) {
+		int rsn_ie_len = sizeof(struct element) + rsn_ie[1];
 		int offset = 8;
 
 		param->mode_802_11i = 2;
 		param->rsn_found = true;
+
 		/* extract RSN capabilities */
-		offset += (rsn_ie[offset] * 4) + 2;
-		offset += (rsn_ie[offset] * 4) + 2;
-		memcpy(param->rsn_cap, &rsn_ie[offset], 2);
+		if (offset < rsn_ie_len) {
+			/* skip over pairwise suites */
+			offset += (rsn_ie[offset] * 4) + 2;
+
+			if (offset < rsn_ie_len) {
+				/* skip over authentication suites */
+				offset += (rsn_ie[offset] * 4) + 2;
+
+				if (offset + 1 < rsn_ie_len)
+					memcpy(param->rsn_cap, &rsn_ie[offset], 2);
+			}
+		}
 	}
 
 	if (param->rsn_found) {
@@ -488,6 +513,7 @@
 			param->akm_suites[i] = crypto->akm_suites[i] & 0xFF;
 	}
 
+	kfree(ies_data);
 	return (void *)param;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/mon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/mon.c
@@ -233,7 +233,7 @@
 	wl->monitor_dev->netdev_ops = &wilc_wfi_netdev_ops;
 	wl->monitor_dev->needs_free_netdev = true;
 
-	if (cfg80211_register_netdevice(wl->monitor_dev)) {
+	if (register_netdevice(wl->monitor_dev)) {
 		netdev_err(real_dev, "register_netdevice failed\n");
 		free_netdev(wl->monitor_dev);
 		return NULL;
@@ -251,7 +251,7 @@
 		return;
 
 	if (rtnl_locked)
-		cfg80211_unregister_netdevice(wl->monitor_dev);
+		unregister_netdevice(wl->monitor_dev);
 	else
 		unregister_netdev(wl->monitor_dev);
 	wl->monitor_dev = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/netdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/netdev.c
@@ -724,6 +724,7 @@
 
 	if (skb->dev != ndev) {
 		netdev_err(ndev, "Packet not destined to this device\n");
+		dev_kfree_skb(skb);
 		return NETDEV_TX_OK;
 	}
 
@@ -861,8 +862,7 @@
 
 void wilc_netdev_cleanup(struct wilc *wilc)
 {
-	struct wilc_vif *vif;
-	int srcu_idx, ifc_cnt = 0;
+	struct wilc_vif *vif, *vif_tmp;
 
 	if (!wilc)
 		return;
@@ -872,36 +872,21 @@
 		wilc->firmware = NULL;
 	}
 
-	srcu_idx = srcu_read_lock(&wilc->srcu);
-	list_for_each_entry_rcu(vif, &wilc->vif_list, list) {
+	list_for_each_entry_safe(vif, vif_tmp, &wilc->vif_list, list) {
+		mutex_lock(&wilc->vif_mutex);
+		list_del_rcu(&vif->list);
+		wilc->vif_num--;
+		mutex_unlock(&wilc->vif_mutex);
+		synchronize_srcu(&wilc->srcu);
 		if (vif->ndev)
 			unregister_netdev(vif->ndev);
 	}
-	srcu_read_unlock(&wilc->srcu, srcu_idx);
 
 	wilc_wfi_deinit_mon_interface(wilc, false);
-	flush_workqueue(wilc->hif_workqueue);
 	destroy_workqueue(wilc->hif_workqueue);
 
-	while (ifc_cnt < WILC_NUM_CONCURRENT_IFC) {
-		mutex_lock(&wilc->vif_mutex);
-		if (wilc->vif_num <= 0) {
-			mutex_unlock(&wilc->vif_mutex);
-			break;
-		}
-		vif = wilc_get_wl_to_vif(wilc);
-		if (!IS_ERR(vif))
-			list_del_rcu(&vif->list);
-
-		wilc->vif_num--;
-		mutex_unlock(&wilc->vif_mutex);
-		synchronize_srcu(&wilc->srcu);
-		ifc_cnt++;
-	}
-
 	wilc_wlan_cfg_deinit(wilc);
 	wlan_deinit_locks(wilc);
-	kfree(wilc->bus_data);
 	wiphy_unregister(wilc->wiphy);
 	wiphy_free(wilc->wiphy);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/netdev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/netdev.h
@@ -252,6 +252,7 @@
 	u8 *rx_buffer;
 	u32 rx_buffer_offset;
 	u8 *tx_buffer;
+	u32 *vmm_table;
 
 	struct txq_handle txq[NQUEUES];
 	int txq_entries;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/sdio.c
@@ -20,6 +20,7 @@
 	{ SDIO_DEVICE(SDIO_VENDOR_ID_MICROCHIP_WILC, SDIO_DEVICE_ID_MICROCHIP_WILC1000) },
 	{ },
 };
+MODULE_DEVICE_TABLE(sdio, wilc_sdio_ids);
 
 #define WILC_SDIO_BLOCK_SIZE 512
 
@@ -27,6 +28,7 @@
 	bool irq_gpio;
 	u32 block_size;
 	int has_thrpt_enh3;
+	u8 *cmd53_buf;
 };
 
 struct sdio_cmd52 {
@@ -46,6 +48,7 @@
 	u32 count:		9;
 	u8 *buffer;
 	u32 block_size;
+	bool use_global_buf;
 };
 
 static const struct wilc_hif_func wilc_hif_sdio;
@@ -90,6 +93,8 @@
 {
 	struct sdio_func *func = container_of(wilc->dev, struct sdio_func, dev);
 	int size, ret;
+	struct wilc_sdio *sdio_priv = wilc->bus_data;
+	u8 *buf = cmd->buffer;
 
 	sdio_claim_host(func);
 
@@ -100,12 +105,23 @@
 	else
 		size = cmd->count;
 
+	if (cmd->use_global_buf) {
+		if (size > sizeof(u32))
+			return -EINVAL;
+
+		buf = sdio_priv->cmd53_buf;
+	}
+
 	if (cmd->read_write) {  /* write */
-		ret = sdio_memcpy_toio(func, cmd->address,
-				       (void *)cmd->buffer, size);
+		if (cmd->use_global_buf)
+			memcpy(buf, cmd->buffer, size);
+
+		ret = sdio_memcpy_toio(func, cmd->address, buf, size);
 	} else {        /* read */
-		ret = sdio_memcpy_fromio(func, (void *)cmd->buffer,
-					 cmd->address,  size);
+		ret = sdio_memcpy_fromio(func, buf, cmd->address, size);
+
+		if (cmd->use_global_buf)
+			memcpy(cmd->buffer, buf, size);
 	}
 
 	sdio_release_host(func);
@@ -127,6 +143,12 @@
 	if (!sdio_priv)
 		return -ENOMEM;
 
+	sdio_priv->cmd53_buf = kzalloc(sizeof(u32), GFP_KERNEL);
+	if (!sdio_priv->cmd53_buf) {
+		ret = -ENOMEM;
+		goto free;
+	}
+
 	ret = wilc_cfg80211_init(&wilc, &func->dev, WILC_HIF_SDIO,
 				 &wilc_hif_sdio);
 	if (ret)
@@ -160,6 +182,7 @@
 	irq_dispose_mapping(wilc->dev_irq_num);
 	wilc_netdev_cleanup(wilc);
 free:
+	kfree(sdio_priv->cmd53_buf);
 	kfree(sdio_priv);
 	return ret;
 }
@@ -167,9 +190,12 @@
 static void wilc_sdio_remove(struct sdio_func *func)
 {
 	struct wilc *wilc = sdio_get_drvdata(func);
+	struct wilc_sdio *sdio_priv = wilc->bus_data;
 
 	clk_disable_unprepare(wilc->rtc_clk);
 	wilc_netdev_cleanup(wilc);
+	kfree(sdio_priv->cmd53_buf);
+	kfree(sdio_priv);
 }
 
 static int wilc_sdio_reset(struct wilc *wilc)
@@ -365,8 +391,9 @@
 		cmd.address = WILC_SDIO_FBR_DATA_REG;
 		cmd.block_mode = 0;
 		cmd.increment = 1;
-		cmd.count = 4;
+		cmd.count = sizeof(u32);
 		cmd.buffer = (u8 *)&data;
+		cmd.use_global_buf = true;
 		cmd.block_size = sdio_priv->block_size;
 		ret = wilc_sdio_cmd53(wilc, &cmd);
 		if (ret)
@@ -404,6 +431,7 @@
 	nblk = size / block_size;
 	nleft = size % block_size;
 
+	cmd.use_global_buf = false;
 	if (nblk > 0) {
 		cmd.block_mode = 1;
 		cmd.increment = 1;
@@ -482,8 +510,9 @@
 		cmd.address = WILC_SDIO_FBR_DATA_REG;
 		cmd.block_mode = 0;
 		cmd.increment = 1;
-		cmd.count = 4;
+		cmd.count = sizeof(u32);
 		cmd.buffer = (u8 *)data;
+		cmd.use_global_buf = true;
 
 		cmd.block_size = sdio_priv->block_size;
 		ret = wilc_sdio_cmd53(wilc, &cmd);
@@ -525,6 +554,7 @@
 	nblk = size / block_size;
 	nleft = size % block_size;
 
+	cmd.use_global_buf = false;
 	if (nblk > 0) {
 		cmd.block_mode = 1;
 		cmd.increment = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/spi.c
@@ -182,9 +182,11 @@
 static int wilc_bus_remove(struct spi_device *spi)
 {
 	struct wilc *wilc = spi_get_drvdata(spi);
+	struct wilc_spi *spi_priv = wilc->bus_data;
 
 	clk_disable_unprepare(wilc->rtc_clk);
 	wilc_netdev_cleanup(wilc);
+	kfree(spi_priv);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/microchip/wilc1000/wlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/microchip/wilc1000/wlan.c
@@ -701,7 +701,7 @@
 	int ret = 0;
 	int counter;
 	int timeout;
-	u32 vmm_table[WILC_VMM_TBL_SIZE];
+	u32 *vmm_table = wilc->vmm_table;
 	u8 ac_pkt_num_to_chip[NQUEUES] = {0, 0, 0, 0};
 	const struct wilc_hif_func *func;
 	int srcu_idx;
@@ -1220,6 +1220,8 @@
 	while ((rqe = wilc_wlan_rxq_remove(wilc)))
 		kfree(rqe);
 
+	kfree(wilc->vmm_table);
+	wilc->vmm_table = NULL;
 	kfree(wilc->rx_buffer);
 	wilc->rx_buffer = NULL;
 	kfree(wilc->tx_buffer);
@@ -1455,6 +1457,14 @@
 		goto fail;
 	}
 
+	if (!wilc->vmm_table)
+		wilc->vmm_table = kcalloc(WILC_VMM_TBL_SIZE, sizeof(u32), GFP_KERNEL);
+
+	if (!wilc->vmm_table) {
+		ret = -ENOBUFS;
+		goto fail;
+	}
+
 	if (!wilc->tx_buffer)
 		wilc->tx_buffer = kmalloc(WILC_TX_BUFF_SIZE, GFP_KERNEL);
 
@@ -1479,7 +1489,8 @@
 	return 0;
 
 fail:
-
+	kfree(wilc->vmm_table);
+	wilc->vmm_table = NULL;
 	kfree(wilc->rx_buffer);
 	wilc->rx_buffer = NULL;
 	kfree(wilc->tx_buffer);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/quantenna/qtnfmac/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/quantenna/qtnfmac/core.c
@@ -811,13 +811,11 @@
 	bus->fw_state = QTNF_FW_STATE_DETACHED;
 
 	if (bus->workqueue) {
-		flush_workqueue(bus->workqueue);
 		destroy_workqueue(bus->workqueue);
 		bus->workqueue = NULL;
 	}
 
 	if (bus->hprio_workqueue) {
-		flush_workqueue(bus->hprio_workqueue);
 		destroy_workqueue(bus->hprio_workqueue);
 		bus->hprio_workqueue = NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/quantenna/qtnfmac/pcie/pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/quantenna/qtnfmac/pcie/pcie.c
@@ -387,7 +387,6 @@
 	return 0;
 
 error:
-	flush_workqueue(pcie_priv->workqueue);
 	destroy_workqueue(pcie_priv->workqueue);
 	pci_set_drvdata(pdev, NULL);
 	return ret;
@@ -416,7 +415,6 @@
 		qtnf_core_detach(bus);
 
 	netif_napi_del(&bus->mux_napi);
-	flush_workqueue(priv->workqueue);
 	destroy_workqueue(priv->workqueue);
 	tasklet_kill(&priv->reclaim_tq);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2400pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2400pci.c
@@ -1023,9 +1023,9 @@
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
-	char bbp_state;
-	char rf_state;
+	bool put_to_sleep;
+	u8 bbp_state;
+	u8 rf_state;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -1561,7 +1561,7 @@
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2400pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2400pci.h
@@ -939,7 +939,7 @@
 #define DEFAULT_TXPOWER	39
 
 #define __CLAMP_TX(__txpower) \
-	clamp_t(char, (__txpower), MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, (__txpower), MIN_TXPOWER, MAX_TXPOWER)
 
 #define TXPOWER_FROM_DEV(__txpower) \
 	((__CLAMP_TX(__txpower) - MAX_TXPOWER) + MIN_TXPOWER)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2500pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2500pci.c
@@ -1176,9 +1176,9 @@
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
-	char bbp_state;
-	char rf_state;
+	bool put_to_sleep;
+	u8 bbp_state;
+	u8 rf_state;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -1856,7 +1856,7 @@
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2500pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2500pci.h
@@ -1219,6 +1219,6 @@
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT2500PCI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2500usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2500usb.c
@@ -984,9 +984,9 @@
 	u16 reg;
 	u16 reg2;
 	unsigned int i;
-	char put_to_sleep;
-	char bbp_state;
-	char rf_state;
+	bool put_to_sleep;
+	u8 bbp_state;
+	u8 rf_state;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -1663,7 +1663,7 @@
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2500usb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2500usb.h
@@ -839,6 +839,6 @@
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT2500USB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
@@ -3310,10 +3310,10 @@
 	if (rt2x00_has_cap_bt_coexist(rt2x00dev)) {
 		if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F)) {
 			/* r55/r59 value array of channel 1~14 */
-			static const char r55_bt_rev[] = {0x83, 0x83,
+			static const u8 r55_bt_rev[] = {0x83, 0x83,
 				0x83, 0x73, 0x73, 0x63, 0x53, 0x53,
 				0x53, 0x43, 0x43, 0x43, 0x43, 0x43};
-			static const char r59_bt_rev[] = {0x0e, 0x0e,
+			static const u8 r59_bt_rev[] = {0x0e, 0x0e,
 				0x0e, 0x0e, 0x0e, 0x0b, 0x0a, 0x09,
 				0x07, 0x07, 0x07, 0x07, 0x07, 0x07};
 
@@ -3322,7 +3322,7 @@
 			rt2800_rfcsr_write(rt2x00dev, 59,
 					   r59_bt_rev[idx]);
 		} else {
-			static const char r59_bt[] = {0x8b, 0x8b, 0x8b,
+			static const u8 r59_bt[] = {0x8b, 0x8b, 0x8b,
 				0x8b, 0x8b, 0x8b, 0x8b, 0x8a, 0x89,
 				0x88, 0x88, 0x86, 0x85, 0x84};
 
@@ -3330,10 +3330,10 @@
 		}
 	} else {
 		if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F)) {
-			static const char r55_nonbt_rev[] = {0x23, 0x23,
+			static const u8 r55_nonbt_rev[] = {0x23, 0x23,
 				0x23, 0x23, 0x13, 0x13, 0x03, 0x03,
 				0x03, 0x03, 0x03, 0x03, 0x03, 0x03};
-			static const char r59_nonbt_rev[] = {0x07, 0x07,
+			static const u8 r59_nonbt_rev[] = {0x07, 0x07,
 				0x07, 0x07, 0x07, 0x07, 0x07, 0x07,
 				0x07, 0x07, 0x06, 0x05, 0x04, 0x04};
 
@@ -3344,14 +3344,14 @@
 		} else if (rt2x00_rt(rt2x00dev, RT5390) ||
 			   rt2x00_rt(rt2x00dev, RT5392) ||
 			   rt2x00_rt(rt2x00dev, RT6352)) {
-			static const char r59_non_bt[] = {0x8f, 0x8f,
+			static const u8 r59_non_bt[] = {0x8f, 0x8f,
 				0x8f, 0x8f, 0x8f, 0x8f, 0x8f, 0x8d,
 				0x8a, 0x88, 0x88, 0x87, 0x87, 0x86};
 
 			rt2800_rfcsr_write(rt2x00dev, 59,
 					   r59_non_bt[idx]);
 		} else if (rt2x00_rt(rt2x00dev, RT5350)) {
-			static const char r59_non_bt[] = {0x0b, 0x0b,
+			static const u8 r59_non_bt[] = {0x0b, 0x0b,
 				0x0b, 0x0b, 0x0b, 0x0b, 0x0b, 0x0a,
 				0x0a, 0x09, 0x08, 0x07, 0x07, 0x06};
 
@@ -3974,23 +3974,23 @@
 	rt2800_bbp_write(rt2x00dev, 159, cal != 0xff ? cal : 0);
 }
 
-static char rt2800_txpower_to_dev(struct rt2x00_dev *rt2x00dev,
+static s8 rt2800_txpower_to_dev(struct rt2x00_dev *rt2x00dev,
 				  unsigned int channel,
-				  char txpower)
+				  s8 txpower)
 {
 	if (rt2x00_rt(rt2x00dev, RT3593) ||
 	    rt2x00_rt(rt2x00dev, RT3883))
 		txpower = rt2x00_get_field8(txpower, EEPROM_TXPOWER_ALC);
 
 	if (channel <= 14)
-		return clamp_t(char, txpower, MIN_G_TXPOWER, MAX_G_TXPOWER);
+		return clamp_t(s8, txpower, MIN_G_TXPOWER, MAX_G_TXPOWER);
 
 	if (rt2x00_rt(rt2x00dev, RT3593) ||
 	    rt2x00_rt(rt2x00dev, RT3883))
-		return clamp_t(char, txpower, MIN_A_TXPOWER_3593,
+		return clamp_t(s8, txpower, MIN_A_TXPOWER_3593,
 			       MAX_A_TXPOWER_3593);
 	else
-		return clamp_t(char, txpower, MIN_A_TXPOWER, MAX_A_TXPOWER);
+		return clamp_t(s8, txpower, MIN_A_TXPOWER, MAX_A_TXPOWER);
 }
 
 static void rt3883_bbp_adjust(struct rt2x00_dev *rt2x00dev,
@@ -4164,7 +4164,10 @@
 		rt2800_bbp_write(rt2x00dev, 62, 0x37 - rt2x00dev->lna_gain);
 		rt2800_bbp_write(rt2x00dev, 63, 0x37 - rt2x00dev->lna_gain);
 		rt2800_bbp_write(rt2x00dev, 64, 0x37 - rt2x00dev->lna_gain);
-		rt2800_bbp_write(rt2x00dev, 86, 0);
+		if (rt2x00_rt(rt2x00dev, RT6352))
+			rt2800_bbp_write(rt2x00dev, 86, 0x38);
+		else
+			rt2800_bbp_write(rt2x00dev, 86, 0);
 	}
 
 	if (rf->channel <= 14) {
@@ -4365,7 +4368,8 @@
 		reg = (rf->channel <= 14 ? 0x1c : 0x24) + 2*rt2x00dev->lna_gain;
 		rt2800_bbp_write_with_rx_chain(rt2x00dev, 66, reg);
 
-		rt2800_iq_calibrate(rt2x00dev, rf->channel);
+		if (rt2x00_rt(rt2x00dev, RT5592))
+			rt2800_iq_calibrate(rt2x00dev, rf->channel);
 	}
 
 	bbp = rt2800_bbp_read(rt2x00dev, 4);
@@ -5644,7 +5648,8 @@
 	if (qual->vgc_level != vgc_level) {
 		if (rt2x00_rt(rt2x00dev, RT3572) ||
 		    rt2x00_rt(rt2x00dev, RT3593) ||
-		    rt2x00_rt(rt2x00dev, RT3883)) {
+		    rt2x00_rt(rt2x00dev, RT3883) ||
+		    rt2x00_rt(rt2x00dev, RT6352)) {
 			rt2800_bbp_write_with_rx_chain(rt2x00dev, 66,
 						       vgc_level);
 		} else if (rt2x00_rt(rt2x00dev, RT5592)) {
@@ -5867,7 +5872,7 @@
 		rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000404);
 	} else if (rt2x00_rt(rt2x00dev, RT6352)) {
 		rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000401);
-		rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x000C0000);
+		rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x000C0001);
 		rt2800_register_write(rt2x00dev, TX_SW_CFG2, 0x00000000);
 		rt2800_register_write(rt2x00dev, TX_ALC_VGA3, 0x00000000);
 		rt2800_register_write(rt2x00dev, TX0_BB_GAIN_ATTEN, 0x0);
@@ -6129,6 +6134,27 @@
 		reg = rt2800_register_read(rt2x00dev, US_CYC_CNT);
 		rt2x00_set_field32(&reg, US_CYC_CNT_CLOCK_CYCLE, 125);
 		rt2800_register_write(rt2x00dev, US_CYC_CNT, reg);
+	} else if (rt2x00_is_soc(rt2x00dev)) {
+		struct clk *clk = clk_get_sys("bus", NULL);
+		int rate;
+
+		if (IS_ERR(clk)) {
+			clk = clk_get_sys("cpu", NULL);
+
+			if (IS_ERR(clk)) {
+				rate = 125;
+			} else {
+				rate = clk_get_rate(clk) / 3000000;
+				clk_put(clk);
+			}
+		} else {
+			rate = clk_get_rate(clk) / 1000000;
+			clk_put(clk);
+		}
+
+		reg = rt2800_register_read(rt2x00dev, US_CYC_CNT);
+		rt2x00_set_field32(&reg, US_CYC_CNT_CLOCK_CYCLE, rate);
+		rt2800_register_write(rt2x00dev, US_CYC_CNT, reg);
 	}
 
 	reg = rt2800_register_read(rt2x00dev, HT_FBK_CFG0);
@@ -8466,11 +8492,11 @@
 	return 0;
 }
 
-static char rt2800_lp_tx_filter_bw_cal(struct rt2x00_dev *rt2x00dev)
+static s8 rt2800_lp_tx_filter_bw_cal(struct rt2x00_dev *rt2x00dev)
 {
 	unsigned int cnt;
 	u8 bbp_val;
-	char cal_val;
+	s8 cal_val;
 
 	rt2800_bbp_dcoc_write(rt2x00dev, 0, 0x82);
 
@@ -8502,7 +8528,7 @@
 	u8 rx_filter_target_20m = 0x27, rx_filter_target_40m = 0x31;
 	int loop = 0, is_ht40, cnt;
 	u8 bbp_val, rf_val;
-	char cal_r32_init, cal_r32_val, cal_diff;
+	s8 cal_r32_init, cal_r32_val, cal_diff;
 	u8 saverfb5r00, saverfb5r01, saverfb5r03, saverfb5r04, saverfb5r05;
 	u8 saverfb5r06, saverfb5r07;
 	u8 saverfb5r08, saverfb5r17, saverfb5r18, saverfb5r19, saverfb5r20;
@@ -9953,9 +9979,9 @@
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *default_power1;
-	char *default_power2;
-	char *default_power3;
+	s8 *default_power1;
+	s8 *default_power2;
+	s8 *default_power3;
 	unsigned int i, tx_chains, rx_chains;
 	u32 reg;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2800lib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2800lib.h
@@ -22,10 +22,10 @@
 struct rt2800_drv_data {
 	u8 calibration_bw20;
 	u8 calibration_bw40;
-	char rx_calibration_bw20;
-	char rx_calibration_bw40;
-	char tx_calibration_bw20;
-	char tx_calibration_bw40;
+	s8 rx_calibration_bw20;
+	s8 rx_calibration_bw40;
+	s8 tx_calibration_bw20;
+	s8 tx_calibration_bw40;
 	u8 bbp25;
 	u8 bbp26;
 	u8 txmixer_gain_24g;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
@@ -101,6 +101,7 @@
 	rt2x00link_stop_tuner(rt2x00dev);
 	rt2x00queue_stop_queues(rt2x00dev);
 	rt2x00queue_flush_queues(rt2x00dev, true);
+	rt2x00queue_stop_queue(rt2x00dev->bcn);
 
 	/*
 	 * Disable radio.
@@ -1091,6 +1092,7 @@
 	}
 
 	kfree(rt2x00dev->spec.channels_info);
+	kfree(rt2x00dev->chan_survey);
 }
 
 static int rt2x00lib_probe_hw(struct rt2x00_dev *rt2x00dev)
@@ -1267,6 +1269,7 @@
 	rt2x00dev->intf_ap_count = 0;
 	rt2x00dev->intf_sta_count = 0;
 	rt2x00dev->intf_associated = 0;
+	rt2x00dev->intf_beaconing = 0;
 
 	/* Enable the radio */
 	retval = rt2x00lib_enable_radio(rt2x00dev);
@@ -1293,6 +1296,7 @@
 	rt2x00dev->intf_ap_count = 0;
 	rt2x00dev->intf_sta_count = 0;
 	rt2x00dev->intf_associated = 0;
+	rt2x00dev->intf_beaconing = 0;
 }
 
 static inline void rt2x00lib_set_if_combinations(struct rt2x00_dev *rt2x00dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
@@ -598,6 +598,17 @@
 	 */
 	if (changes & BSS_CHANGED_BEACON_ENABLED) {
 		mutex_lock(&intf->beacon_skb_mutex);
+
+		/*
+		 * Clear the 'enable_beacon' flag and clear beacon because
+		 * the beacon queue has been stopped after hardware reset.
+		 */
+		if (test_bit(DEVICE_STATE_RESET, &rt2x00dev->flags) &&
+		    intf->enable_beacon) {
+			intf->enable_beacon = false;
+			rt2x00queue_clear_beacon(rt2x00dev, vif);
+		}
+
 		if (!bss_conf->enable_beacon && intf->enable_beacon) {
 			rt2x00dev->intf_beaconing--;
 			intf->enable_beacon = false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt2x00usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt2x00usb.c
@@ -25,6 +25,9 @@
 	if (status == -ENODEV || status == -ENOENT)
 		return true;
 
+	if (!test_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags))
+		return false;
+
 	if (status == -EPROTO || status == -ETIMEDOUT)
 		rt2x00dev->num_proto_errs++;
 	else
@@ -114,12 +117,12 @@
 				  const u16 buffer_length)
 {
 	int status = 0;
-	unsigned char *tb;
+	u8 *tb;
 	u16 off, len, bsize;
 
 	mutex_lock(&rt2x00dev->csr_mutex);
 
-	tb  = (char *)buffer;
+	tb  = (u8 *)buffer;
 	off = offset;
 	len = buffer_length;
 	while (len && !status) {
@@ -212,7 +215,7 @@
 	rd->cr.wLength = cpu_to_le16(sizeof(u32));
 
 	usb_fill_control_urb(urb, usb_dev, usb_rcvctrlpipe(usb_dev, 0),
-			     (unsigned char *)(&rd->cr), &rd->reg, sizeof(rd->reg),
+			     (u8 *)(&rd->cr), &rd->reg, sizeof(rd->reg),
 			     rt2x00usb_register_read_async_cb, rd);
 	usb_anchor_urb(urb, rt2x00dev->anchor);
 	if (usb_submit_urb(urb, GFP_ATOMIC) < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt61pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt61pci.c
@@ -1709,7 +1709,7 @@
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
+	bool put_to_sleep;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -2656,7 +2656,7 @@
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt61pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt61pci.h
@@ -1484,6 +1484,6 @@
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT61PCI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt73usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt73usb.c
@@ -1378,7 +1378,7 @@
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
+	bool put_to_sleep;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -2090,7 +2090,7 @@
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ralink/rt2x00/rt73usb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ralink/rt2x00/rt73usb.h
@@ -1063,6 +1063,6 @@
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT73USB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ray_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ray_cs.c
@@ -270,13 +270,14 @@
 {
 	ray_dev_t *local;
 	struct net_device *dev;
+	int ret;
 
 	dev_dbg(&p_dev->dev, "ray_attach()\n");
 
 	/* Allocate space for private device-specific data */
 	dev = alloc_etherdev(sizeof(ray_dev_t));
 	if (!dev)
-		goto fail_alloc_dev;
+		return -ENOMEM;
 
 	local = netdev_priv(dev);
 	local->finder = p_dev;
@@ -313,11 +314,16 @@
 	timer_setup(&local->timer, NULL, 0);
 
 	this_device = p_dev;
-	return ray_config(p_dev);
+	ret = ray_config(p_dev);
+	if (ret)
+		goto err_free_dev;
+
+	return 0;
 
-fail_alloc_dev:
-	return -ENOMEM;
-} /* ray_attach */
+err_free_dev:
+	free_netdev(dev);
+	return ret;
+}
 
 static void ray_detach(struct pcmcia_device *link)
 {
@@ -382,6 +388,8 @@
 		goto failed;
 	local->sram = ioremap(link->resource[2]->start,
 			resource_size(link->resource[2]));
+	if (!local->sram)
+		goto failed;
 
 /*** Set up 16k window for shared memory (receive buffer) ***************/
 	link->resource[3]->flags |=
@@ -396,6 +404,8 @@
 		goto failed;
 	local->rmem = ioremap(link->resource[3]->start,
 			resource_size(link->resource[3]));
+	if (!local->rmem)
+		goto failed;
 
 /*** Set up window for attribute memory ***********************************/
 	link->resource[4]->flags |=
@@ -410,6 +420,8 @@
 		goto failed;
 	local->amem = ioremap(link->resource[4]->start,
 			resource_size(link->resource[4]));
+	if (!local->amem)
+		goto failed;
 
 	dev_dbg(&link->dev, "ray_config sram=%p\n", local->sram);
 	dev_dbg(&link->dev, "ray_config rmem=%p\n", local->rmem);
@@ -1637,38 +1649,34 @@
 /*===========================================================================*/
 static int parse_addr(char *in_str, UCHAR *out)
 {
+	int i, k;
 	int len;
-	int i, j, k;
-	int status;
 
 	if (in_str == NULL)
 		return 0;
-	if ((len = strlen(in_str)) < 2)
+	len = strnlen(in_str, ADDRLEN * 2 + 1) - 1;
+	if (len < 1)
 		return 0;
 	memset(out, 0, ADDRLEN);
 
-	status = 1;
-	j = len - 1;
-	if (j > 12)
-		j = 12;
 	i = 5;
 
-	while (j > 0) {
-		if ((k = hex_to_bin(in_str[j--])) != -1)
+	while (len > 0) {
+		if ((k = hex_to_bin(in_str[len--])) != -1)
 			out[i] = k;
 		else
 			return 0;
 
-		if (j == 0)
+		if (len == 0)
 			break;
-		if ((k = hex_to_bin(in_str[j--])) != -1)
+		if ((k = hex_to_bin(in_str[len--])) != -1)
 			out[i] += k << 4;
 		else
 			return 0;
 		if (!i--)
 			break;
 	}
-	return status;
+	return 1;
 }
 
 /*===========================================================================*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/Kconfig
@@ -16,5 +16,6 @@
 source "drivers/net/wireless/realtek/rtlwifi/Kconfig"
 source "drivers/net/wireless/realtek/rtl8xxxu/Kconfig"
 source "drivers/net/wireless/realtek/rtw88/Kconfig"
+source "drivers/net/wireless/realtek/rtw89/Kconfig"
 
 endif # WLAN_VENDOR_REALTEK
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/Makefile
@@ -8,4 +8,5 @@
 obj-$(CONFIG_RTLWIFI)		+= rtlwifi/
 obj-$(CONFIG_RTL8XXXU)		+= rtl8xxxu/
 obj-$(CONFIG_RTW88)		+= rtw88/
+obj-$(CONFIG_RTW89)		+= rtw89/
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c
@@ -460,8 +460,10 @@
 	struct rtl8180_priv *priv = dev->priv;
 	struct rtl8180_tx_ring *ring;
 	struct rtl8180_tx_desc *entry;
+	unsigned int prio = 0;
 	unsigned long flags;
-	unsigned int idx, prio, hw_prio;
+	unsigned int idx, hw_prio;
+
 	dma_addr_t mapping;
 	u32 tx_flags;
 	u8 rc_flags;
@@ -470,7 +472,9 @@
 	/* do arithmetic and then convert to le16 */
 	u16 frame_duration = 0;
 
-	prio = skb_get_queue_mapping(skb);
+	/* rtl8180/rtl8185 only has one useable tx queue */
+	if (dev->queues > IEEE80211_AC_BK)
+		prio = skb_get_queue_mapping(skb);
 	ring = &priv->tx_ring[prio];
 
 	mapping = dma_map_single(&priv->pdev->dev, skb->data, skb->len,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtl818x/rtl8187/rtl8225.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtl818x/rtl8187/rtl8225.c
@@ -28,7 +28,7 @@
 	usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0),
 			RTL8187_REQ_GET_REG, RTL8187_REQT_READ,
 			(unsigned long)addr, idx & 0x03,
-			&priv->io_dmabuf->bits8, sizeof(val), HZ / 2);
+			&priv->io_dmabuf->bits8, sizeof(val), 500);
 
 	val = priv->io_dmabuf->bits8;
 	mutex_unlock(&priv->io_mutex);
@@ -45,7 +45,7 @@
 	usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0),
 			RTL8187_REQ_GET_REG, RTL8187_REQT_READ,
 			(unsigned long)addr, idx & 0x03,
-			&priv->io_dmabuf->bits16, sizeof(val), HZ / 2);
+			&priv->io_dmabuf->bits16, sizeof(val), 500);
 
 	val = priv->io_dmabuf->bits16;
 	mutex_unlock(&priv->io_mutex);
@@ -62,7 +62,7 @@
 	usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0),
 			RTL8187_REQ_GET_REG, RTL8187_REQT_READ,
 			(unsigned long)addr, idx & 0x03,
-			&priv->io_dmabuf->bits32, sizeof(val), HZ / 2);
+			&priv->io_dmabuf->bits32, sizeof(val), 500);
 
 	val = priv->io_dmabuf->bits32;
 	mutex_unlock(&priv->io_mutex);
@@ -79,7 +79,7 @@
 	usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
 			RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
 			(unsigned long)addr, idx & 0x03,
-			&priv->io_dmabuf->bits8, sizeof(val), HZ / 2);
+			&priv->io_dmabuf->bits8, sizeof(val), 500);
 
 	mutex_unlock(&priv->io_mutex);
 }
@@ -93,7 +93,7 @@
 	usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
 			RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
 			(unsigned long)addr, idx & 0x03,
-			&priv->io_dmabuf->bits16, sizeof(val), HZ / 2);
+			&priv->io_dmabuf->bits16, sizeof(val), 500);
 
 	mutex_unlock(&priv->io_mutex);
 }
@@ -107,7 +107,7 @@
 	usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
 			RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
 			(unsigned long)addr, idx & 0x03,
-			&priv->io_dmabuf->bits32, sizeof(val), HZ / 2);
+			&priv->io_dmabuf->bits32, sizeof(val), 500);
 
 	mutex_unlock(&priv->io_mutex);
 }
@@ -183,7 +183,7 @@
 	usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
 			RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
 			addr, 0x8225, &priv->io_dmabuf->bits16, sizeof(data),
-			HZ / 2);
+			500);
 
 	mutex_unlock(&priv->io_mutex);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h
@@ -1190,7 +1190,7 @@
 			u8 bw;
 		} __packed ra_report;
 	};
-};
+} __packed;
 
 struct rtl8xxxu_fileops;
 
@@ -1346,6 +1346,7 @@
 	u32 rege9c;
 	u32 regeb4;
 	u32 regebc;
+	u32 regrcr;
 	int next_mbox;
 	int nr_out_eps;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c
@@ -1669,6 +1669,11 @@
 	val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
 	val8 &= ~BIT(0);
 	rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
+
+	/*
+	 * Fix transmission failure of rtl8192e.
+	 */
+	rtl8xxxu_write8(priv, REG_TXPAUSE, 0x00);
 }
 
 struct rtl8xxxu_fileops rtl8192eu_fops = {
@@ -1695,6 +1700,7 @@
 	.rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24),
 	.has_s0s1 = 0,
 	.gen2_thermal_meter = 1,
+	.needs_full_init = 1,
 	.adda_1t_init = 0x0fc01616,
 	.adda_1t_path_on = 0x0fc01616,
 	.adda_2t_path_on_a = 0x0fc01616,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
@@ -28,6 +28,7 @@
 #include <linux/wireless.h>
 #include <linux/firmware.h>
 #include <linux/moduleparam.h>
+#include <linux/bitfield.h>
 #include <net/mac80211.h>
 #include "rtl8xxxu.h"
 #include "rtl8xxxu_regs.h"
@@ -1389,13 +1390,13 @@
 	u8 cck[RTL8723A_MAX_RF_PATHS], ofdm[RTL8723A_MAX_RF_PATHS];
 	u8 ofdmbase[RTL8723A_MAX_RF_PATHS], mcsbase[RTL8723A_MAX_RF_PATHS];
 	u32 val32, ofdm_a, ofdm_b, mcs_a, mcs_b;
-	u8 val8;
+	u8 val8, base;
 	int group, i;
 
 	group = rtl8xxxu_gen1_channel_to_group(channel);
 
-	cck[0] = priv->cck_tx_power_index_A[group] - 1;
-	cck[1] = priv->cck_tx_power_index_B[group] - 1;
+	cck[0] = priv->cck_tx_power_index_A[group];
+	cck[1] = priv->cck_tx_power_index_B[group];
 
 	if (priv->hi_pa) {
 		if (cck[0] > 0x20)
@@ -1406,10 +1407,6 @@
 
 	ofdm[0] = priv->ht40_1s_tx_power_index_A[group];
 	ofdm[1] = priv->ht40_1s_tx_power_index_B[group];
-	if (ofdm[0])
-		ofdm[0] -= 1;
-	if (ofdm[1])
-		ofdm[1] -= 1;
 
 	ofdmbase[0] = ofdm[0] +	priv->ofdm_tx_power_index_diff[group].a;
 	ofdmbase[1] = ofdm[1] +	priv->ofdm_tx_power_index_diff[group].b;
@@ -1498,20 +1495,19 @@
 
 	rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS15_MCS12,
 			 mcs_a + power_base->reg_0e1c);
+	val8 = u32_get_bits(mcs_a + power_base->reg_0e1c, 0xff000000);
 	for (i = 0; i < 3; i++) {
-		if (i != 2)
-			val8 = (mcsbase[0] > 8) ? (mcsbase[0] - 8) : 0;
-		else
-			val8 = (mcsbase[0] > 6) ? (mcsbase[0] - 6) : 0;
+		base = i != 2 ? 8 : 6;
+		val8 = max_t(int, val8 - base, 0);
 		rtl8xxxu_write8(priv, REG_OFDM0_XC_TX_IQ_IMBALANCE + i, val8);
 	}
+
 	rtl8xxxu_write32(priv, REG_TX_AGC_B_MCS15_MCS12,
 			 mcs_b + power_base->reg_0868);
+	val8 = u32_get_bits(mcs_b + power_base->reg_0868, 0xff000000);
 	for (i = 0; i < 3; i++) {
-		if (i != 2)
-			val8 = (mcsbase[1] > 8) ? (mcsbase[1] - 8) : 0;
-		else
-			val8 = (mcsbase[1] > 6) ? (mcsbase[1] - 6) : 0;
+		base = i != 2 ? 8 : 6;
+		val8 = max_t(int, val8 - base, 0);
 		rtl8xxxu_write8(priv, REG_OFDM0_XD_TX_IQ_IMBALANCE + i, val8);
 	}
 }
@@ -1607,18 +1603,18 @@
 static int rtl8xxxu_identify_chip(struct rtl8xxxu_priv *priv)
 {
 	struct device *dev = &priv->udev->dev;
-	u32 val32, bonding;
+	u32 val32, bonding, sys_cfg;
 	u16 val16;
 
-	val32 = rtl8xxxu_read32(priv, REG_SYS_CFG);
-	priv->chip_cut = (val32 & SYS_CFG_CHIP_VERSION_MASK) >>
+	sys_cfg = rtl8xxxu_read32(priv, REG_SYS_CFG);
+	priv->chip_cut = (sys_cfg & SYS_CFG_CHIP_VERSION_MASK) >>
 		SYS_CFG_CHIP_VERSION_SHIFT;
-	if (val32 & SYS_CFG_TRP_VAUX_EN) {
+	if (sys_cfg & SYS_CFG_TRP_VAUX_EN) {
 		dev_info(dev, "Unsupported test chip\n");
 		return -ENOTSUPP;
 	}
 
-	if (val32 & SYS_CFG_BT_FUNC) {
+	if (sys_cfg & SYS_CFG_BT_FUNC) {
 		if (priv->chip_cut >= 3) {
 			sprintf(priv->chip_name, "8723BU");
 			priv->rtl_chip = RTL8723B;
@@ -1640,7 +1636,7 @@
 		if (val32 & MULTI_GPS_FUNC_EN)
 			priv->has_gps = 1;
 		priv->is_multi_func = 1;
-	} else if (val32 & SYS_CFG_TYPE_ID) {
+	} else if (sys_cfg & SYS_CFG_TYPE_ID) {
 		bonding = rtl8xxxu_read32(priv, REG_HPON_FSM);
 		bonding &= HPON_FSM_BONDING_MASK;
 		if (priv->fops->tx_desc_size ==
@@ -1688,7 +1684,7 @@
 	case RTL8188E:
 	case RTL8192E:
 	case RTL8723B:
-		switch (val32 & SYS_CFG_VENDOR_EXT_MASK) {
+		switch (sys_cfg & SYS_CFG_VENDOR_EXT_MASK) {
 		case SYS_CFG_VENDOR_ID_TSMC:
 			sprintf(priv->chip_vendor, "TSMC");
 			break;
@@ -1705,7 +1701,7 @@
 		}
 		break;
 	default:
-		if (val32 & SYS_CFG_VENDOR_ID) {
+		if (sys_cfg & SYS_CFG_VENDOR_ID) {
 			sprintf(priv->chip_vendor, "UMC");
 			priv->vendor_umc = 1;
 		} else {
@@ -1874,13 +1870,6 @@
 
 		/* We have 8 bits to indicate validity */
 		map_addr = offset * 8;
-		if (map_addr >= EFUSE_MAP_LEN) {
-			dev_warn(dev, "%s: Illegal map_addr (%04x), "
-				 "efuse corrupt!\n",
-				 __func__, map_addr);
-			ret = -EINVAL;
-			goto exit;
-		}
 		for (i = 0; i < EFUSE_MAX_WORD_UNIT; i++) {
 			/* Check word enable condition in the section */
 			if (word_mask & BIT(i)) {
@@ -1891,6 +1880,13 @@
 			ret = rtl8xxxu_read_efuse8(priv, efuse_addr++, &val8);
 			if (ret)
 				goto exit;
+			if (map_addr >= EFUSE_MAP_LEN - 1) {
+				dev_warn(dev, "%s: Illegal map_addr (%04x), "
+					 "efuse corrupt!\n",
+					 __func__, map_addr);
+				ret = -EINVAL;
+				goto exit;
+			}
 			priv->efuse_wifi.raw[map_addr++] = val8;
 
 			ret = rtl8xxxu_read_efuse8(priv, efuse_addr++, &val8);
@@ -2925,12 +2921,12 @@
 		}
 
 		if (!(simubitmap & 0x30) && priv->tx_paths > 1) {
-			/* path B RX OK */
+			/* path B TX OK */
 			for (i = 4; i < 6; i++)
 				result[3][i] = result[c1][i];
 		}
 
-		if (!(simubitmap & 0x30) && priv->tx_paths > 1) {
+		if (!(simubitmap & 0xc0) && priv->tx_paths > 1) {
 			/* path B RX OK */
 			for (i = 6; i < 8; i++)
 				result[3][i] = result[c1][i];
@@ -4045,6 +4041,7 @@
 		RCR_ACCEPT_MGMT_FRAME | RCR_HTC_LOC_CTRL |
 		RCR_APPEND_PHYSTAT | RCR_APPEND_ICV | RCR_APPEND_MIC;
 	rtl8xxxu_write32(priv, REG_RCR, val32);
+	priv->regrcr = val32;
 
 	/*
 	 * Accept all multicast
@@ -4338,15 +4335,14 @@
 	h2c.b_macid_cfg.ramask2 = (ramask >> 16) & 0xff;
 	h2c.b_macid_cfg.ramask3 = (ramask >> 24) & 0xff;
 
-	h2c.ramask.arg = 0x80;
 	h2c.b_macid_cfg.data1 = rateid;
 	if (sgi)
 		h2c.b_macid_cfg.data1 |= BIT(7);
 
 	h2c.b_macid_cfg.data2 = bw;
 
-	dev_dbg(&priv->udev->dev, "%s: rate mask %08x, arg %02x, size %zi\n",
-		__func__, ramask, h2c.ramask.arg, sizeof(h2c.b_macid_cfg));
+	dev_dbg(&priv->udev->dev, "%s: rate mask %08x, rateid %02x, sgi %d, size %zi\n",
+		__func__, ramask, rateid, sgi, sizeof(h2c.b_macid_cfg));
 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.b_macid_cfg));
 }
 
@@ -4370,12 +4366,9 @@
 void rtl8xxxu_gen2_report_connect(struct rtl8xxxu_priv *priv,
 				  u8 macid, bool connect)
 {
-#ifdef RTL8XXXU_GEN2_REPORT_CONNECT
 	/*
-	 * Barry Day reports this causes issues with 8192eu and 8723bu
-	 * devices reconnecting. The reason for this is unclear, but
-	 * until it is better understood, leave the code in place but
-	 * disabled, so it is not lost.
+	 * The firmware turns on the rate control when it knows it's
+	 * connected to a network.
 	 */
 	struct h2c_cmd h2c;
 
@@ -4388,7 +4381,6 @@
 		h2c.media_status_rpt.parm &= ~BIT(0);
 
 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.media_status_rpt));
-#endif
 }
 
 void rtl8xxxu_gen1_init_aggregation(struct rtl8xxxu_priv *priv)
@@ -4508,6 +4500,53 @@
 	return network_type;
 }
 
+static void rtl8xxxu_set_aifs(struct rtl8xxxu_priv *priv, u8 slot_time)
+{
+	u32 reg_edca_param[IEEE80211_NUM_ACS] = {
+		[IEEE80211_AC_VO] = REG_EDCA_VO_PARAM,
+		[IEEE80211_AC_VI] = REG_EDCA_VI_PARAM,
+		[IEEE80211_AC_BE] = REG_EDCA_BE_PARAM,
+		[IEEE80211_AC_BK] = REG_EDCA_BK_PARAM,
+	};
+	u32 val32;
+	u16 wireless_mode = 0;
+	u8 aifs, aifsn, sifs;
+	int i;
+
+	if (priv->vif) {
+		struct ieee80211_sta *sta;
+
+		rcu_read_lock();
+		sta = ieee80211_find_sta(priv->vif, priv->vif->bss_conf.bssid);
+		if (sta)
+			wireless_mode = rtl8xxxu_wireless_mode(priv->hw, sta);
+		rcu_read_unlock();
+	}
+
+	if (priv->hw->conf.chandef.chan->band == NL80211_BAND_5GHZ ||
+	    (wireless_mode & WIRELESS_MODE_N_24G))
+		sifs = 16;
+	else
+		sifs = 10;
+
+	for (i = 0; i < IEEE80211_NUM_ACS; i++) {
+		val32 = rtl8xxxu_read32(priv, reg_edca_param[i]);
+
+		/* It was set in conf_tx. */
+		aifsn = val32 & 0xff;
+
+		/* aifsn not set yet or already fixed */
+		if (aifsn < 2 || aifsn > 15)
+			continue;
+
+		aifs = aifsn * slot_time + sifs;
+
+		val32 &= ~0xff;
+		val32 |= aifs;
+		rtl8xxxu_write32(priv, reg_edca_param[i], val32);
+	}
+}
+
 static void
 rtl8xxxu_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 			  struct ieee80211_bss_conf *bss_conf, u32 changed)
@@ -4593,6 +4632,8 @@
 		else
 			val8 = 20;
 		rtl8xxxu_write8(priv, REG_SLOT, val8);
+
+		rtl8xxxu_set_aifs(priv, val8);
 	}
 
 	if (changed & BSS_CHANGED_BSSID) {
@@ -4984,6 +5025,8 @@
 	if (control && control->sta)
 		sta = control->sta;
 
+	queue = rtl8xxxu_queue_select(hw, skb);
+
 	tx_desc = skb_push(skb, tx_desc_size);
 
 	memset(tx_desc, 0, tx_desc_size);
@@ -4996,7 +5039,6 @@
 	    is_broadcast_ether_addr(ieee80211_get_DA(hdr)))
 		tx_desc->txdw0 |= TXDESC_BROADMULTICAST;
 
-	queue = rtl8xxxu_queue_select(hw, skb);
 	tx_desc->txdw1 = cpu_to_le32(queue << TXDESC_QUEUE_SHIFT);
 
 	if (tx_info->control.hw_key) {
@@ -5139,7 +5181,7 @@
 		pending = priv->rx_urb_pending_count;
 	} else {
 		skb = (struct sk_buff *)rx_urb->urb.context;
-		dev_kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 		usb_free_urb(&rx_urb->urb);
 	}
 
@@ -5445,9 +5487,6 @@
 	btcoex = &priv->bt_coex;
 	rarpt = &priv->ra_report;
 
-	if (priv->rf_paths > 1)
-		goto out;
-
 	while (!skb_queue_empty(&priv->c2hcmd_queue)) {
 		skb = skb_dequeue(&priv->c2hcmd_queue);
 
@@ -5468,7 +5507,6 @@
 			rarpt->txrate.flags = 0;
 			rate = c2h->ra_report.rate;
 			sgi = c2h->ra_report.sgi;
-			bw = c2h->ra_report.bw;
 
 			if (rate < DESC_RATE_MCS0) {
 				rarpt->txrate.legacy =
@@ -5485,8 +5523,13 @@
 						RATE_INFO_FLAGS_SHORT_GI;
 				}
 
-				if (bw == RATE_INFO_BW_20)
-					rarpt->txrate.bw |= RATE_INFO_BW_20;
+				if (skb->len >= offsetofend(typeof(*c2h), ra_report.bw)) {
+					if (c2h->ra_report.bw == RTL8XXXU_CHANNEL_WIDTH_40)
+						bw = RATE_INFO_BW_40;
+					else
+						bw = RATE_INFO_BW_20;
+					rarpt->txrate.bw = bw;
+				}
 			}
 			bit_rate = cfg80211_calculate_bitrate(&rarpt->txrate);
 			rarpt->bit_rate = bit_rate;
@@ -5495,10 +5538,9 @@
 		default:
 			break;
 		}
-	}
 
-out:
-	dev_kfree_skb(skb);
+		dev_kfree_skb(skb);
+	}
 }
 
 static void rtl8723bu_handle_c2h(struct rtl8xxxu_priv *priv,
@@ -5864,7 +5906,6 @@
 {
 	struct rtl8xxxu_priv *priv = hw->priv;
 	struct device *dev = &priv->udev->dev;
-	u16 val16;
 	int ret = 0, channel;
 	bool ht40;
 
@@ -5874,14 +5915,6 @@
 			 __func__, hw->conf.chandef.chan->hw_value,
 			 changed, hw->conf.chandef.width);
 
-	if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS) {
-		val16 = ((hw->conf.long_frame_max_tx_count <<
-			  RETRY_LIMIT_LONG_SHIFT) & RETRY_LIMIT_LONG_MASK) |
-			((hw->conf.short_frame_max_tx_count <<
-			  RETRY_LIMIT_SHORT_SHIFT) & RETRY_LIMIT_SHORT_MASK);
-		rtl8xxxu_write16(priv, REG_RETRY_LIMIT, val16);
-	}
-
 	if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
 		switch (hw->conf.chandef.width) {
 		case NL80211_CHAN_WIDTH_20_NOHT:
@@ -5964,7 +5997,7 @@
 				      unsigned int *total_flags, u64 multicast)
 {
 	struct rtl8xxxu_priv *priv = hw->priv;
-	u32 rcr = rtl8xxxu_read32(priv, REG_RCR);
+	u32 rcr = priv->regrcr;
 
 	dev_dbg(&priv->udev->dev, "%s: changed_flags %08x, total_flags %08x\n",
 		__func__, changed_flags, *total_flags);
@@ -6010,6 +6043,7 @@
 	 */
 
 	rtl8xxxu_write32(priv, REG_RCR, rcr);
+	priv->regrcr = rcr;
 
 	*total_flags &= (FIF_ALLMULTI | FIF_FCSFAIL | FIF_BCN_PRBRESP_PROMISC |
 			 FIF_CONTROL | FIF_OTHER_BSS | FIF_PSPOLL |
@@ -6446,6 +6480,7 @@
 	if (priv->usb_interrupts)
 		rtl8xxxu_write32(priv, REG_USB_HIMR, 0);
 
+	cancel_work_sync(&priv->c2hcmd_work);
 	cancel_delayed_work_sync(&priv->ra_watchdog);
 
 	rtl8xxxu_free_rx_resources(priv);
@@ -6935,6 +6970,18 @@
 	.driver_info = (unsigned long)&rtl8192eu_fops},
 {USB_DEVICE_AND_INTERFACE_INFO(USB_VENDOR_ID_REALTEK, 0x818c, 0xff, 0xff, 0xff),
 	.driver_info = (unsigned long)&rtl8192eu_fops},
+/* D-Link DWA-131 rev C1 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x3312, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8192eu_fops},
+/* TP-Link TL-WN8200ND V2 */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2357, 0x0126, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8192eu_fops},
+/* Mercusys MW300UM */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2c4e, 0x0100, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8192eu_fops},
+/* Mercusys MW300UH */
+{USB_DEVICE_AND_INTERFACE_INFO(0x2c4e, 0x0104, 0xff, 0xff, 0xff),
+	.driver_info = (unsigned long)&rtl8192eu_fops},
 #endif
 { }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/base.c
@@ -452,8 +452,7 @@
 	/* <1> timer */
 	timer_setup(&rtlpriv->works.watchdog_timer,
 		    rtl_watch_dog_timer_callback, 0);
-	timer_setup(&rtlpriv->works.dualmac_easyconcurrent_retrytimer,
-		    rtl_easy_concurrent_retrytimer_callback, 0);
+
 	/* <2> work queue */
 	rtlpriv->works.hw = hw;
 	rtlpriv->works.rtl_wq = wq;
@@ -576,9 +575,15 @@
 
 void rtl_deinit_core(struct ieee80211_hw *hw)
 {
+	struct rtl_priv *rtlpriv = rtl_priv(hw);
+
 	rtl_c2hcmd_launcher(hw, 0);
 	rtl_free_entries_from_scan_list(hw);
 	rtl_free_entries_from_ack_queue(hw, false);
+	if (rtlpriv->works.rtl_wq) {
+		destroy_workqueue(rtlpriv->works.rtl_wq);
+		rtlpriv->works.rtl_wq = NULL;
+	}
 }
 EXPORT_SYMBOL_GPL(rtl_deinit_core);
 
@@ -1994,8 +1999,7 @@
 	struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
 	unsigned long flags;
 
-	struct rtl_bssid_entry *entry;
-	bool entry_found = false;
+	struct rtl_bssid_entry *entry = NULL, *iter;
 
 	/* check if it is scanning */
 	if (!mac->act_scanning)
@@ -2008,10 +2012,10 @@
 
 	spin_lock_irqsave(&rtlpriv->locks.scan_list_lock, flags);
 
-	list_for_each_entry(entry, &rtlpriv->scan_list.list, list) {
-		if (memcmp(entry->bssid, hdr->addr3, ETH_ALEN) == 0) {
-			list_del_init(&entry->list);
-			entry_found = true;
+	list_for_each_entry(iter, &rtlpriv->scan_list.list, list) {
+		if (memcmp(iter->bssid, hdr->addr3, ETH_ALEN) == 0) {
+			list_del_init(&iter->list);
+			entry = iter;
 			rtl_dbg(rtlpriv, COMP_SCAN, DBG_LOUD,
 				"Update BSSID=%pM to scan list (total=%d)\n",
 				hdr->addr3, rtlpriv->scan_list.num);
@@ -2019,7 +2023,7 @@
 		}
 	}
 
-	if (!entry_found) {
+	if (!entry) {
 		entry = kmalloc(sizeof(*entry), GFP_ATOMIC);
 
 		if (!entry)
@@ -2366,19 +2370,6 @@
 	rtl_c2hcmd_launcher(hw, 1);
 }
 
-void rtl_easy_concurrent_retrytimer_callback(struct timer_list *t)
-{
-	struct rtl_priv *rtlpriv =
-		from_timer(rtlpriv, t, works.dualmac_easyconcurrent_retrytimer);
-	struct ieee80211_hw *hw = rtlpriv->hw;
-	struct rtl_priv *buddy_priv = rtlpriv->buddy_priv;
-
-	if (buddy_priv == NULL)
-		return;
-
-	rtlpriv->cfg->ops->dualmac_easy_concurrent(hw);
-}
-
 /*********************************************************
  *
  * frame process functions
@@ -2724,9 +2715,6 @@
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Realtek 802.11n PCI wireless core");
 
-struct rtl_global_var rtl_global_var = {};
-EXPORT_SYMBOL_GPL(rtl_global_var);
-
 static int __init rtl_core_module_init(void)
 {
 	BUILD_BUG_ON(TX_PWR_BY_RATE_NUM_RATE < TX_PWR_BY_RATE_NUM_SECTION);
@@ -2740,10 +2728,6 @@
 	/* add debugfs */
 	rtl_debugfs_add_topdir();
 
-	/* init some global vars */
-	INIT_LIST_HEAD(&rtl_global_var.glb_priv_list);
-	spin_lock_init(&rtl_global_var.glb_list_lock);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/base.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/base.h
@@ -124,8 +124,6 @@
 u8 *rtl_find_ie(u8 *data, unsigned int len, u8 ie);
 void rtl_recognize_peer(struct ieee80211_hw *hw, u8 *data, unsigned int len);
 u8 rtl_tid_to_ac(u8 tid);
-void rtl_easy_concurrent_retrytimer_callback(struct timer_list *t);
-extern struct rtl_global_var rtl_global_var;
 void rtl_phy_scan_operation_backup(struct ieee80211_hw *hw, u8 operation);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/debug.c
@@ -278,8 +278,8 @@
 
 	tmp_len = (count > sizeof(tmp) - 1 ? sizeof(tmp) - 1 : count);
 
-	if (!buffer || copy_from_user(tmp, buffer, tmp_len))
-		return count;
+	if (copy_from_user(tmp, buffer, tmp_len))
+		return -EFAULT;
 
 	tmp[tmp_len] = '\0';
 
@@ -287,7 +287,7 @@
 	num = sscanf(tmp, "%x %x %x", &addr, &val, &len);
 
 	if (num !=  3)
-		return count;
+		return -EINVAL;
 
 	switch (len) {
 	case 1:
@@ -329,8 +329,8 @@
 
 	tmp_len = (count > sizeof(tmp) - 1 ? sizeof(tmp) - 1 : count);
 
-	if (!buffer || copy_from_user(tmp, buffer, tmp_len))
-		return count;
+	if (copy_from_user(tmp, buffer, tmp_len))
+		return -EFAULT;
 
 	tmp[tmp_len] = '\0';
 
@@ -340,8 +340,8 @@
 			 &h2c_data[4], &h2c_data[5],
 			 &h2c_data[6], &h2c_data[7]);
 
-	if (h2c_len <= 0)
-		return count;
+	if (h2c_len == 0)
+		return -EINVAL;
 
 	for (i = 0; i < h2c_len; i++)
 		h2c_data_packed[i] = (u8)h2c_data[i];
@@ -375,8 +375,8 @@
 
 	tmp_len = (count > sizeof(tmp) - 1 ? sizeof(tmp) - 1 : count);
 
-	if (!buffer || copy_from_user(tmp, buffer, tmp_len))
-		return count;
+	if (copy_from_user(tmp, buffer, tmp_len))
+		return -EFAULT;
 
 	tmp[tmp_len] = '\0';
 
@@ -386,7 +386,7 @@
 	if (num != 4) {
 		rtl_dbg(rtlpriv, COMP_ERR, DBG_DMESG,
 			"Format is <path> <addr> <mask> <data>\n");
-		return count;
+		return -EINVAL;
 	}
 
 	rtl_set_rfreg(hw, path, addr, bitmask, data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/pci.c
@@ -164,21 +164,29 @@
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
 
+	value &= PCI_EXP_LNKCTL_ASPMC;
+
 	if (rtlhal->hw_type != HARDWARE_TYPE_RTL8192SE)
-		value |= 0x40;
+		value |= PCI_EXP_LNKCTL_CCC;
 
-	pci_write_config_byte(rtlpci->pdev, 0x80, value);
+	pcie_capability_clear_and_set_word(rtlpci->pdev, PCI_EXP_LNKCTL,
+					   PCI_EXP_LNKCTL_ASPMC | value,
+					   value);
 
 	return false;
 }
 
-/*When we set 0x01 to enable clk request. Set 0x0 to disable clk req.*/
-static void _rtl_pci_switch_clk_req(struct ieee80211_hw *hw, u8 value)
+/* @value is PCI_EXP_LNKCTL_CLKREQ_EN or 0 to enable/disable clk request. */
+static void _rtl_pci_switch_clk_req(struct ieee80211_hw *hw, u16 value)
 {
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
 
-	pci_write_config_byte(rtlpci->pdev, 0x81, value);
+	value &= PCI_EXP_LNKCTL_CLKREQ_EN;
+
+	pcie_capability_clear_and_set_word(rtlpci->pdev, PCI_EXP_LNKCTL,
+					   PCI_EXP_LNKCTL_CLKREQ_EN,
+					   value);
 
 	if (rtlhal->hw_type == HARDWARE_TYPE_RTL8192SE)
 		udelay(100);
@@ -192,11 +200,8 @@
 	struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	u8 pcibridge_vendor = pcipriv->ndis_adapter.pcibridge_vendor;
-	u8 num4bytes = pcipriv->ndis_adapter.num4bytes;
 	/*Retrieve original configuration settings. */
 	u8 linkctrl_reg = pcipriv->ndis_adapter.linkctrl_reg;
-	u16 pcibridge_linkctrlreg = pcipriv->ndis_adapter.
-				pcibridge_linkctrlreg;
 	u16 aspmlevel = 0;
 	u8 tmp_u1b = 0;
 
@@ -221,16 +226,8 @@
 	/*Set corresponding value. */
 	aspmlevel |= BIT(0) | BIT(1);
 	linkctrl_reg &= ~aspmlevel;
-	pcibridge_linkctrlreg &= ~(BIT(0) | BIT(1));
 
 	_rtl_pci_platform_switch_device_pci_aspm(hw, linkctrl_reg);
-	udelay(50);
-
-	/*4 Disable Pci Bridge ASPM */
-	pci_write_config_byte(rtlpci->pdev, (num4bytes << 2),
-			      pcibridge_linkctrlreg);
-
-	udelay(50);
 }
 
 /*Enable RTL8192SE ASPM & Enable Pci Bridge ASPM for
@@ -245,9 +242,7 @@
 	struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	u8 pcibridge_vendor = pcipriv->ndis_adapter.pcibridge_vendor;
-	u8 num4bytes = pcipriv->ndis_adapter.num4bytes;
 	u16 aspmlevel;
-	u8 u_pcibridge_aspmsetting;
 	u8 u_device_aspmsetting;
 
 	if (!ppsc->support_aspm)
@@ -259,25 +254,6 @@
 		return;
 	}
 
-	/*4 Enable Pci Bridge ASPM */
-
-	u_pcibridge_aspmsetting =
-	    pcipriv->ndis_adapter.pcibridge_linkctrlreg |
-	    rtlpci->const_hostpci_aspm_setting;
-
-	if (pcibridge_vendor == PCI_BRIDGE_VENDOR_INTEL)
-		u_pcibridge_aspmsetting &= ~BIT(0);
-
-	pci_write_config_byte(rtlpci->pdev, (num4bytes << 2),
-			      u_pcibridge_aspmsetting);
-
-	rtl_dbg(rtlpriv, COMP_INIT, DBG_LOUD,
-		"PlatformEnableASPM(): Write reg[%x] = %x\n",
-		(pcipriv->ndis_adapter.pcibridge_pciehdr_offset + 0x10),
-		u_pcibridge_aspmsetting);
-
-	udelay(50);
-
 	/*Get ASPM level (with/without Clock Req) */
 	aspmlevel = rtlpci->const_devicepci_aspm_setting;
 	u_device_aspmsetting = pcipriv->ndis_adapter.linkctrl_reg;
@@ -291,7 +267,8 @@
 
 	if (ppsc->reg_rfps_level & RT_RF_OFF_LEVL_CLK_REQ) {
 		_rtl_pci_switch_clk_req(hw, (ppsc->reg_rfps_level &
-					     RT_RF_OFF_LEVL_CLK_REQ) ? 1 : 0);
+					     RT_RF_OFF_LEVL_CLK_REQ) ?
+					     PCI_EXP_LNKCTL_CLKREQ_EN : 0);
 		RT_SET_PS_LEVEL(ppsc, RT_RF_OFF_LEVL_CLK_REQ);
 	}
 	udelay(100);
@@ -318,63 +295,6 @@
 	return status;
 }
 
-static bool rtl_pci_check_buddy_priv(struct ieee80211_hw *hw,
-				     struct rtl_priv **buddy_priv)
-{
-	struct rtl_priv *rtlpriv = rtl_priv(hw);
-	struct rtl_pci_priv *pcipriv = rtl_pcipriv(hw);
-	bool find_buddy_priv = false;
-	struct rtl_priv *tpriv;
-	struct rtl_pci_priv *tpcipriv = NULL;
-
-	if (!list_empty(&rtlpriv->glb_var->glb_priv_list)) {
-		list_for_each_entry(tpriv, &rtlpriv->glb_var->glb_priv_list,
-				    list) {
-			tpcipriv = (struct rtl_pci_priv *)tpriv->priv;
-			rtl_dbg(rtlpriv, COMP_INIT, DBG_LOUD,
-				"pcipriv->ndis_adapter.funcnumber %x\n",
-				pcipriv->ndis_adapter.funcnumber);
-			rtl_dbg(rtlpriv, COMP_INIT, DBG_LOUD,
-				"tpcipriv->ndis_adapter.funcnumber %x\n",
-				tpcipriv->ndis_adapter.funcnumber);
-
-			if (pcipriv->ndis_adapter.busnumber ==
-			    tpcipriv->ndis_adapter.busnumber &&
-			    pcipriv->ndis_adapter.devnumber ==
-			    tpcipriv->ndis_adapter.devnumber &&
-			    pcipriv->ndis_adapter.funcnumber !=
-			    tpcipriv->ndis_adapter.funcnumber) {
-				find_buddy_priv = true;
-				break;
-			}
-		}
-	}
-
-	rtl_dbg(rtlpriv, COMP_INIT, DBG_LOUD,
-		"find_buddy_priv %d\n", find_buddy_priv);
-
-	if (find_buddy_priv)
-		*buddy_priv = tpriv;
-
-	return find_buddy_priv;
-}
-
-static void rtl_pci_get_linkcontrol_field(struct ieee80211_hw *hw)
-{
-	struct rtl_pci_priv *pcipriv = rtl_pcipriv(hw);
-	struct rtl_pci *rtlpci = rtl_pcidev(pcipriv);
-	u8 capabilityoffset = pcipriv->ndis_adapter.pcibridge_pciehdr_offset;
-	u8 linkctrl_reg;
-	u8 num4bbytes;
-
-	num4bbytes = (capabilityoffset + 0x10) / 4;
-
-	/*Read  Link Control Register */
-	pci_read_config_byte(rtlpci->pdev, (num4bbytes << 2), &linkctrl_reg);
-
-	pcipriv->ndis_adapter.pcibridge_linkctrlreg = linkctrl_reg;
-}
-
 static void rtl_pci_parse_configuration(struct pci_dev *pdev,
 					struct ieee80211_hw *hw)
 {
@@ -483,11 +403,6 @@
 	if (!rtlpriv->rtlhal.earlymode_enable)
 		return;
 
-	if (rtlpriv->dm.supp_phymode_switch &&
-	    (rtlpriv->easy_concurrent_ctl.switch_in_process ||
-	    (rtlpriv->buddy_priv &&
-	    rtlpriv->buddy_priv->easy_concurrent_ctl.switch_in_process)))
-		return;
 	/* we just use em for BE/BK/VI/VO */
 	for (tid = 7; tid >= 0; tid--) {
 		u8 hw_queue = ac_to_hwq[rtl_tid_to_ac(tid)];
@@ -1742,9 +1657,6 @@
 	synchronize_irq(rtlpci->pdev->irq);
 	tasklet_kill(&rtlpriv->works.irq_tasklet);
 	cancel_work_sync(&rtlpriv->works.lps_change_work);
-
-	flush_workqueue(rtlpriv->works.rtl_wq);
-	destroy_workqueue(rtlpriv->works.rtl_wq);
 }
 
 static int rtl_pci_init(struct ieee80211_hw *hw, struct pci_dev *pdev)
@@ -2035,12 +1947,6 @@
 		    PCI_SLOT(bridge_pdev->devfn);
 		pcipriv->ndis_adapter.pcibridge_funcnum =
 		    PCI_FUNC(bridge_pdev->devfn);
-		pcipriv->ndis_adapter.pcibridge_pciehdr_offset =
-		    pci_pcie_cap(bridge_pdev);
-		pcipriv->ndis_adapter.num4bytes =
-		    (pcipriv->ndis_adapter.pcibridge_pciehdr_offset + 0x10) / 4;
-
-		rtl_pci_get_linkcontrol_field(hw);
 
 		if (pcipriv->ndis_adapter.pcibridge_vendor ==
 		    PCI_BRIDGE_VENDOR_AMD) {
@@ -2057,17 +1963,14 @@
 		pdev->vendor, pcipriv->ndis_adapter.linkctrl_reg);
 
 	rtl_dbg(rtlpriv, COMP_INIT, DBG_DMESG,
-		"pci_bridge busnumber:devnumber:funcnumber:vendor:pcie_cap:link_ctl_reg:amd %d:%d:%d:%x:%x:%x:%x\n",
+		"pci_bridge busnumber:devnumber:funcnumber:vendor:amd %d:%d:%d:%x:%x\n",
 		pcipriv->ndis_adapter.pcibridge_busnum,
 		pcipriv->ndis_adapter.pcibridge_devnum,
 		pcipriv->ndis_adapter.pcibridge_funcnum,
 		pcibridge_vendors[pcipriv->ndis_adapter.pcibridge_vendor],
-		pcipriv->ndis_adapter.pcibridge_pciehdr_offset,
-		pcipriv->ndis_adapter.pcibridge_linkctrlreg,
 		pcipriv->ndis_adapter.amd_l1_patch);
 
 	rtl_pci_parse_configuration(pdev, hw);
-	list_add_tail(&rtlpriv->list, &rtlpriv->glb_var->glb_priv_list);
 
 	return true;
 }
@@ -2214,7 +2117,6 @@
 	rtlpriv->rtlhal.interface = INTF_PCI;
 	rtlpriv->cfg = (struct rtl_hal_cfg *)(id->driver_data);
 	rtlpriv->intf_ops = &rtl_pci_ops;
-	rtlpriv->glb_var = &rtl_global_var;
 	rtl_efuse_ops_init(hw);
 
 	/* MEM map */
@@ -2265,7 +2167,7 @@
 	if (rtlpriv->cfg->ops->init_sw_vars(hw)) {
 		pr_err("Can't init_sw_vars\n");
 		err = -ENODEV;
-		goto fail3;
+		goto fail2;
 	}
 	rtlpriv->cfg->ops->init_sw_leds(hw);
 
@@ -2283,14 +2185,14 @@
 	err = rtl_pci_init(hw, pdev);
 	if (err) {
 		pr_err("Failed to init PCI\n");
-		goto fail3;
+		goto fail4;
 	}
 
 	err = ieee80211_register_hw(hw);
 	if (err) {
 		pr_err("Can't register mac80211 hw.\n");
 		err = -ENODEV;
-		goto fail3;
+		goto fail5;
 	}
 	rtlpriv->mac80211.mac80211_registered = 1;
 
@@ -2313,16 +2215,19 @@
 	set_bit(RTL_STATUS_INTERFACE_START, &rtlpriv->status);
 	return 0;
 
-fail3:
-	pci_set_drvdata(pdev, NULL);
+fail5:
+	rtl_pci_deinit(hw);
+fail4:
 	rtl_deinit_core(hw);
+fail3:
+	wait_for_completion(&rtlpriv->firmware_loading_complete);
+	rtlpriv->cfg->ops->deinit_sw_vars(hw);
 
 fail2:
 	if (rtlpriv->io.pci_mem_start != 0)
 		pci_iounmap(pdev, (void __iomem *)rtlpriv->io.pci_mem_start);
 
 	pci_release_regions(pdev);
-	complete(&rtlpriv->firmware_loading_complete);
 
 fail1:
 	if (hw)
@@ -2373,7 +2278,6 @@
 	if (rtlpci->using_msi)
 		pci_disable_msi(rtlpci->pdev);
 
-	list_del(&rtlpriv->list);
 	if (rtlpriv->io.pci_mem_start != 0) {
 		pci_iounmap(pdev, (void __iomem *)rtlpriv->io.pci_mem_start);
 		pci_release_regions(pdev);
@@ -2433,7 +2337,6 @@
 	.read_efuse_byte = read_efuse_byte,
 	.adapter_start = rtl_pci_start,
 	.adapter_stop = rtl_pci_stop,
-	.check_buddy_priv = rtl_pci_check_buddy_priv,
 	.adapter_tx = rtl_pci_tx,
 	.flush = rtl_pci_flush,
 	.reset_trx_ring = rtl_pci_reset_trx_ring,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/pci.h
@@ -236,11 +236,6 @@
 	u16 pcibridge_vendorid;
 	u16 pcibridge_deviceid;
 
-	u8 num4bytes;
-
-	u8 pcibridge_pciehdr_offset;
-	u8 pcibridge_linkctrlreg;
-
 	bool amd_l1_patch;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c
@@ -799,7 +799,7 @@
 	}
 
 	if (rtlpriv->btcoexist.bt_edca_dl != 0) {
-		edca_be_ul = rtlpriv->btcoexist.bt_edca_dl;
+		edca_be_dl = rtlpriv->btcoexist.bt_edca_dl;
 		bt_change_edca = true;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c
@@ -68,8 +68,10 @@
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	struct rtl8192_tx_ring *ring = &rtlpci->tx_ring[BEACON_QUEUE];
+	struct sk_buff_head free_list;
 	unsigned long flags;
 
+	skb_queue_head_init(&free_list);
 	spin_lock_irqsave(&rtlpriv->locks.irq_th_lock, flags);
 	while (skb_queue_len(&ring->queue)) {
 		struct rtl_tx_desc *entry = &ring->desc[ring->idx];
@@ -79,10 +81,12 @@
 				 rtlpriv->cfg->ops->get_desc(hw, (u8 *)entry,
 						true, HW_DESC_TXBUFF_ADDR),
 				 skb->len, DMA_TO_DEVICE);
-		kfree_skb(skb);
+		__skb_queue_tail(&free_list, skb);
 		ring->idx = (ring->idx + 1) % ring->entries;
 	}
 	spin_unlock_irqrestore(&rtlpriv->locks.irq_th_lock, flags);
+
+	__skb_queue_purge(&free_list);
 }
 
 static void _rtl88ee_disable_bcn_sub_func(struct ieee80211_hw *hw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c
@@ -16,12 +16,6 @@
 static void _rtl88e_phy_rf_serial_write(struct ieee80211_hw *hw,
 					enum radio_path rfpath, u32 offset,
 					u32 data);
-static u32 _rtl88e_phy_calculate_bit_shift(u32 bitmask)
-{
-	u32 i = ffs(bitmask);
-
-	return i ? i - 1 : 32;
-}
 static bool _rtl88e_phy_bb8188e_config_parafile(struct ieee80211_hw *hw);
 static bool _rtl88e_phy_config_mac_with_headerfile(struct ieee80211_hw *hw);
 static bool phy_config_bb_with_headerfile(struct ieee80211_hw *hw,
@@ -51,7 +45,7 @@
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
 		"regaddr(%#x), bitmask(%#x)\n", regaddr, bitmask);
 	originalvalue = rtl_read_dword(rtlpriv, regaddr);
-	bitshift = _rtl88e_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	returnvalue = (originalvalue & bitmask) >> bitshift;
 
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
@@ -74,7 +68,7 @@
 
 	if (bitmask != MASKDWORD) {
 		originalvalue = rtl_read_dword(rtlpriv, regaddr);
-		bitshift = _rtl88e_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = ((originalvalue & (~bitmask)) | (data << bitshift));
 	}
 
@@ -99,7 +93,7 @@
 
 
 	original_value = _rtl88e_phy_rf_serial_read(hw, rfpath, regaddr);
-	bitshift = _rtl88e_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 
 	spin_unlock(&rtlpriv->locks.rf_lock);
@@ -127,7 +121,7 @@
 			original_value = _rtl88e_phy_rf_serial_read(hw,
 								    rfpath,
 								    regaddr);
-			bitshift = _rtl88e_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c
@@ -640,7 +640,7 @@
 	}
 
 	if (rtlpriv->btcoexist.bt_edca_dl != 0) {
-		edca_be_ul = rtlpriv->btcoexist.bt_edca_dl;
+		edca_be_dl = rtlpriv->btcoexist.bt_edca_dl;
 		bt_change_edca = true;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c
@@ -17,7 +17,7 @@
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE, "regaddr(%#x), bitmask(%#x)\n",
 		regaddr, bitmask);
 	originalvalue = rtl_read_dword(rtlpriv, regaddr);
-	bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	returnvalue = (originalvalue & bitmask) >> bitshift;
 
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
@@ -40,7 +40,7 @@
 
 	if (bitmask != MASKDWORD) {
 		originalvalue = rtl_read_dword(rtlpriv, regaddr);
-		bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = ((originalvalue & (~bitmask)) | (data << bitshift));
 	}
 
@@ -143,14 +143,6 @@
 }
 EXPORT_SYMBOL(_rtl92c_phy_rf_serial_write);
 
-u32 _rtl92c_phy_calculate_bit_shift(u32 bitmask)
-{
-	u32 i = ffs(bitmask);
-
-	return i ? i - 1 : 32;
-}
-EXPORT_SYMBOL(_rtl92c_phy_calculate_bit_shift);
-
 static void _rtl92c_phy_bb_config_1t(struct ieee80211_hw *hw)
 {
 	rtl_set_bbreg(hw, RFPGA0_TXINFO, 0x3, 0x2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.h
@@ -196,7 +196,6 @@
 void rtl92ce_phy_set_rf_on(struct ieee80211_hw *hw);
 void rtl92c_phy_set_io(struct ieee80211_hw *hw);
 void rtl92c_bb_block_on(struct ieee80211_hw *hw);
-u32 _rtl92c_phy_calculate_bit_shift(u32 bitmask);
 long _rtl92c_phy_txpwr_idx_to_dbm(struct ieee80211_hw *hw,
 				  enum wireless_mode wirelessmode,
 				  u8 txpwridx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/phy.c
@@ -39,7 +39,7 @@
 							       rfpath, regaddr);
 	}
 
-	bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 
 	spin_unlock(&rtlpriv->locks.rf_lock);
@@ -110,7 +110,7 @@
 			original_value = _rtl92c_phy_rf_serial_read(hw,
 								    rfpath,
 								    regaddr);
-			bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
@@ -122,7 +122,7 @@
 			original_value = _rtl92c_phy_fw_rf_serial_read(hw,
 								       rfpath,
 								       regaddr);
-			bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/phy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/phy.h
@@ -94,7 +94,6 @@
 			       u32 offset);
 u32 _rtl92c_phy_fw_rf_serial_read(struct ieee80211_hw *hw,
 				  enum radio_path rfpath, u32 offset);
-u32 _rtl92c_phy_calculate_bit_shift(u32 bitmask);
 void _rtl92c_phy_rf_serial_write(struct ieee80211_hw *hw,
 				 enum radio_path rfpath, u32 offset, u32 data);
 void _rtl92c_phy_fw_rf_serial_write(struct ieee80211_hw *hw,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c
@@ -1000,6 +1000,7 @@
 	_initpabias(hw);
 	rtl92c_dm_init(hw);
 exit:
+	local_irq_disable();
 	local_irq_restore(flags);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/phy.c
@@ -32,7 +32,7 @@
 		original_value = _rtl92c_phy_fw_rf_serial_read(hw,
 							       rfpath, regaddr);
 	}
-	bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
 		"regaddr(%#x), rfpath(%#x), bitmask(%#x), original_value(%#x)\n",
@@ -56,7 +56,7 @@
 			original_value = _rtl92c_phy_rf_serial_read(hw,
 								    rfpath,
 								    regaddr);
-			bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
@@ -67,7 +67,7 @@
 			original_value = _rtl92c_phy_fw_rf_serial_read(hw,
 								       rfpath,
 								       regaddr);
-			bitshift = _rtl92c_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192de/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192de/phy.c
@@ -169,13 +169,6 @@
 	157, 159, 161, 163, 165
 };
 
-static u32 _rtl92d_phy_calculate_bit_shift(u32 bitmask)
-{
-	u32 i = ffs(bitmask);
-
-	return i ? i - 1 : 32;
-}
-
 u32 rtl92d_phy_query_bb_reg(struct ieee80211_hw *hw, u32 regaddr, u32 bitmask)
 {
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
@@ -198,7 +191,7 @@
 	} else {
 		originalvalue = rtl_read_dword(rtlpriv, regaddr);
 	}
-	bitshift = _rtl92d_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	returnvalue = (originalvalue & bitmask) >> bitshift;
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
 		"BBR MASK=0x%x Addr[0x%x]=0x%x\n",
@@ -230,7 +223,7 @@
 					dbi_direct);
 		else
 			originalvalue = rtl_read_dword(rtlpriv, regaddr);
-		bitshift = _rtl92d_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = ((originalvalue & (~bitmask)) | (data << bitshift));
 	}
 	if (rtlhal->during_mac1init_radioa || rtlhal->during_mac0init_radiob)
@@ -317,7 +310,7 @@
 		regaddr, rfpath, bitmask);
 	spin_lock(&rtlpriv->locks.rf_lock);
 	original_value = _rtl92d_phy_rf_serial_read(hw, rfpath, regaddr);
-	bitshift = _rtl92d_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 	spin_unlock(&rtlpriv->locks.rf_lock);
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
@@ -343,7 +336,7 @@
 		if (bitmask != RFREG_OFFSET_MASK) {
 			original_value = _rtl92d_phy_rf_serial_read(hw,
 				rfpath, regaddr);
-			bitshift = _rtl92d_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data = ((original_value & (~bitmask)) |
 				(data << bitshift));
 		}
@@ -899,8 +892,8 @@
 	u8 place = chnl;
 
 	if (chnl > 14) {
-		for (place = 14; place < sizeof(channel5g); place++) {
-			if (channel5g[place] == chnl) {
+		for (place = 14; place < ARRAY_SIZE(channel_all); place++) {
+			if (channel_all[place] == chnl) {
 				place++;
 				break;
 			}
@@ -1366,7 +1359,7 @@
 	u8 place;
 
 	if (chnl > 14) {
-		for (place = 14; place < sizeof(channel_all); place++) {
+		for (place = 14; place < ARRAY_SIZE(channel_all); place++) {
 			if (channel_all[place] == chnl)
 				return place - 13;
 		}
@@ -2386,14 +2379,10 @@
 			rtl_dbg(rtlpriv, COMP_SCAN, DBG_LOUD,
 				"Just Read IQK Matrix reg for channel:%d....\n",
 				channel);
-			if ((rtlphy->iqk_matrix[indexforchannel].
-			     value[0] != NULL)
-				/*&&(regea4 != 0) */)
+			if (rtlphy->iqk_matrix[indexforchannel].value[0][0] != 0)
 				_rtl92d_phy_patha_fill_iqk_matrix(hw, true,
-					rtlphy->iqk_matrix[
-					indexforchannel].value,	0,
-					(rtlphy->iqk_matrix[
-					indexforchannel].value[0][2] == 0));
+					rtlphy->iqk_matrix[indexforchannel].value, 0,
+					rtlphy->iqk_matrix[indexforchannel].value[0][2] == 0);
 			if (IS_92D_SINGLEPHY(rtlhal->version)) {
 				if ((rtlphy->iqk_matrix[
 					indexforchannel].value[0][4] != 0)
@@ -2428,7 +2417,7 @@
 
 	int i;
 
-	for (i = 0; i < sizeof(channel5g); i++)
+	for (i = 0; i < ARRAY_SIZE(channel5g); i++)
 		if (channel == channel5g[i])
 			return true;
 	return false;
@@ -2692,9 +2681,8 @@
 	u8 i;
 
 	rtl_dbg(rtlpriv, COMP_INIT, DBG_LOUD,
-		"settings regs %d default regs %d\n",
-		(int)(sizeof(rtlphy->iqk_matrix) /
-		      sizeof(struct iqk_matrix_regs)),
+		"settings regs %zu default regs %d\n",
+		ARRAY_SIZE(rtlphy->iqk_matrix),
 		IQK_MATRIX_REG_NUM);
 	/* 0xe94, 0xe9c, 0xea4, 0xeac, 0xeb4, 0xebc, 0xec4, 0xecc */
 	for (i = 0; i < IQK_MATRIX_SETTINGS_NUM; i++) {
@@ -2861,16 +2849,14 @@
 	case BAND_ON_5G:
 		/* Get first channel error when change between
 		 * 5G and 2.4G band. */
-		if (channel <= 14)
+		if (WARN_ONCE(channel <= 14, "rtl8192de: 5G but channel<=14\n"))
 			return 0;
-		WARN_ONCE((channel <= 14), "rtl8192de: 5G but channel<=14\n");
 		break;
 	case BAND_ON_2_4G:
 		/* Get first channel error when change between
 		 * 5G and 2.4G band. */
-		if (channel > 14)
+		if (WARN_ONCE(channel > 14, "rtl8192de: 2G but channel>14\n"))
 			return 0;
-		WARN_ONCE((channel > 14), "rtl8192de: 2G but channel>14\n");
 		break;
 	default:
 		WARN_ONCE(true, "rtl8192de: Invalid WirelessMode(%#x)!!\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c
@@ -35,7 +35,7 @@
 
 static void _rtl92de_query_rxphystatus(struct ieee80211_hw *hw,
 				       struct rtl_stats *pstats,
-				       struct rx_desc_92d *pdesc,
+				       __le32 *pdesc,
 				       struct rx_fwinfo_92d *p_drvinfo,
 				       bool packet_match_bssid,
 				       bool packet_toself,
@@ -49,8 +49,10 @@
 	u8 i, max_spatial_stream;
 	u32 rssi, total_rssi = 0;
 	bool is_cck_rate;
+	u8 rxmcs;
 
-	is_cck_rate = RX_HAL_IS_CCK_RATE(pdesc->rxmcs);
+	rxmcs = get_rx_desc_rxmcs(pdesc);
+	is_cck_rate = rxmcs <= DESC_RATE11M;
 	pstats->packet_matchbssid = packet_match_bssid;
 	pstats->packet_toself = packet_toself;
 	pstats->packet_beacon = packet_beacon;
@@ -158,8 +160,8 @@
 		pstats->rx_pwdb_all = pwdb_all;
 		pstats->rxpower = rx_pwr_all;
 		pstats->recvsignalpower = rx_pwr_all;
-		if (pdesc->rxht && pdesc->rxmcs >= DESC_RATEMCS8 &&
-		    pdesc->rxmcs <= DESC_RATEMCS15)
+		if (get_rx_desc_rxht(pdesc) && rxmcs >= DESC_RATEMCS8 &&
+		    rxmcs <= DESC_RATEMCS15)
 			max_spatial_stream = 2;
 		else
 			max_spatial_stream = 1;
@@ -365,7 +367,7 @@
 static void _rtl92de_translate_rx_signal_stuff(struct ieee80211_hw *hw,
 					       struct sk_buff *skb,
 					       struct rtl_stats *pstats,
-					       struct rx_desc_92d *pdesc,
+					       __le32 *pdesc,
 					       struct rx_fwinfo_92d *p_drvinfo)
 {
 	struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
@@ -414,7 +416,8 @@
 	stats->icv = (u16)get_rx_desc_icv(pdesc);
 	stats->crc = (u16)get_rx_desc_crc32(pdesc);
 	stats->hwerror = (stats->crc | stats->icv);
-	stats->decrypted = !get_rx_desc_swdec(pdesc);
+	stats->decrypted = !get_rx_desc_swdec(pdesc) &&
+			   get_rx_desc_enc_type(pdesc) != RX_DESC_ENC_NONE;
 	stats->rate = (u8)get_rx_desc_rxmcs(pdesc);
 	stats->shortpreamble = (u16)get_rx_desc_splcp(pdesc);
 	stats->isampdu = (bool)(get_rx_desc_paggr(pdesc) == 1);
@@ -427,8 +430,6 @@
 	rx_status->band = hw->conf.chandef.chan->band;
 	if (get_rx_desc_crc32(pdesc))
 		rx_status->flag |= RX_FLAG_FAILED_FCS_CRC;
-	if (!get_rx_desc_swdec(pdesc))
-		rx_status->flag |= RX_FLAG_DECRYPTED;
 	if (get_rx_desc_bw(pdesc))
 		rx_status->bw = RATE_INFO_BW_40;
 	if (get_rx_desc_rxht(pdesc))
@@ -442,9 +443,7 @@
 	if (phystatus) {
 		p_drvinfo = (struct rx_fwinfo_92d *)(skb->data +
 						     stats->rx_bufshift);
-		_rtl92de_translate_rx_signal_stuff(hw,
-						   skb, stats,
-						   (struct rx_desc_92d *)pdesc,
+		_rtl92de_translate_rx_signal_stuff(hw, skb, stats, pdesc,
 						   p_drvinfo);
 	}
 	/*rx_status->qual = stats->signal; */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.h
@@ -14,6 +14,15 @@
 #define USB_HWDESC_HEADER_LEN			32
 #define CRCLENGTH				4
 
+enum rtl92d_rx_desc_enc {
+	RX_DESC_ENC_NONE	= 0,
+	RX_DESC_ENC_WEP40	= 1,
+	RX_DESC_ENC_TKIP_WO_MIC	= 2,
+	RX_DESC_ENC_TKIP_MIC	= 3,
+	RX_DESC_ENC_AES		= 4,
+	RX_DESC_ENC_WEP104	= 5,
+};
+
 /* macros to read/write various fields in RX or TX descriptors */
 
 static inline void set_tx_desc_pkt_size(__le32 *__pdesc, u32 __val)
@@ -246,6 +255,11 @@
 	return le32_get_bits(*__pdesc, GENMASK(19, 16));
 }
 
+static inline u32 get_rx_desc_enc_type(__le32 *__pdesc)
+{
+	return le32_get_bits(*__pdesc, GENMASK(22, 20));
+}
+
 static inline u32 get_rx_desc_shift(__le32 *__pdesc)
 {
 	return le32_get_bits(*__pdesc, GENMASK(25, 24));
@@ -380,10 +394,17 @@
 	u8 csi_target[2];
 	u8 sigevm;
 	u8 max_ex_pwr;
+#ifdef __LITTLE_ENDIAN
 	u8 ex_intf_flag:1;
 	u8 sgi_en:1;
 	u8 rxsc:2;
 	u8 reserve:4;
+#else
+	u8 reserve:4;
+	u8 rxsc:2;
+	u8 sgi_en:1;
+	u8 ex_intf_flag:1;
+#endif
 } __packed;
 
 struct tx_desc_92d {
@@ -488,64 +509,6 @@
 	u32 reserve_pass_pcie_mm_limit[4];
 } __packed;
 
-struct rx_desc_92d {
-	u32 length:14;
-	u32 crc32:1;
-	u32 icverror:1;
-	u32 drv_infosize:4;
-	u32 security:3;
-	u32 qos:1;
-	u32 shift:2;
-	u32 phystatus:1;
-	u32 swdec:1;
-	u32 lastseg:1;
-	u32 firstseg:1;
-	u32 eor:1;
-	u32 own:1;
-
-	u32 macid:5;
-	u32 tid:4;
-	u32 hwrsvd:5;
-	u32 paggr:1;
-	u32 faggr:1;
-	u32 a1_fit:4;
-	u32 a2_fit:4;
-	u32 pam:1;
-	u32 pwr:1;
-	u32 moredata:1;
-	u32 morefrag:1;
-	u32 type:2;
-	u32 mc:1;
-	u32 bc:1;
-
-	u32 seq:12;
-	u32 frag:4;
-	u32 nextpktlen:14;
-	u32 nextind:1;
-	u32 rsvd:1;
-
-	u32 rxmcs:6;
-	u32 rxht:1;
-	u32 amsdu:1;
-	u32 splcp:1;
-	u32 bandwidth:1;
-	u32 htc:1;
-	u32 tcpchk_rpt:1;
-	u32 ipcchk_rpt:1;
-	u32 tcpchk_valid:1;
-	u32 hwpcerr:1;
-	u32 hwpcind:1;
-	u32 iv0:16;
-
-	u32 iv1;
-
-	u32 tsfl;
-
-	u32 bufferaddress;
-	u32 bufferaddress64;
-
-} __packed;
-
 void rtl92de_tx_fill_desc(struct ieee80211_hw *hw,
 			  struct ieee80211_hdr *hdr, u8 *pdesc,
 			  u8 *pbd_desc_tx, struct ieee80211_tx_info *info,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c
@@ -16,7 +16,6 @@
 static void _rtl92ee_phy_rf_serial_write(struct ieee80211_hw *hw,
 					 enum radio_path rfpath, u32 offset,
 					 u32 data);
-static u32 _rtl92ee_phy_calculate_bit_shift(u32 bitmask);
 static bool _rtl92ee_phy_bb8192ee_config_parafile(struct ieee80211_hw *hw);
 static bool _rtl92ee_phy_config_mac_with_headerfile(struct ieee80211_hw *hw);
 static bool phy_config_bb_with_hdr_file(struct ieee80211_hw *hw,
@@ -46,7 +45,7 @@
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
 		"regaddr(%#x), bitmask(%#x)\n", regaddr, bitmask);
 	originalvalue = rtl_read_dword(rtlpriv, regaddr);
-	bitshift = _rtl92ee_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	returnvalue = (originalvalue & bitmask) >> bitshift;
 
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE,
@@ -68,7 +67,7 @@
 
 	if (bitmask != MASKDWORD) {
 		originalvalue = rtl_read_dword(rtlpriv, regaddr);
-		bitshift = _rtl92ee_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = ((originalvalue & (~bitmask)) | (data << bitshift));
 	}
 
@@ -92,7 +91,7 @@
 	spin_lock(&rtlpriv->locks.rf_lock);
 
 	original_value = _rtl92ee_phy_rf_serial_read(hw , rfpath, regaddr);
-	bitshift = _rtl92ee_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 
 	spin_unlock(&rtlpriv->locks.rf_lock);
@@ -119,7 +118,7 @@
 
 	if (bitmask != RFREG_OFFSET_MASK) {
 		original_value = _rtl92ee_phy_rf_serial_read(hw, rfpath, addr);
-		bitshift = _rtl92ee_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = (original_value & (~bitmask)) | (data << bitshift);
 	}
 
@@ -201,13 +200,6 @@
 		pphyreg->rf3wire_offset, data_and_addr);
 }
 
-static u32 _rtl92ee_phy_calculate_bit_shift(u32 bitmask)
-{
-	u32 i = ffs(bitmask);
-
-	return i ? i - 1 : 32;
-}
-
 bool rtl92ee_phy_mac_config(struct ieee80211_hw *hw)
 {
 	return _rtl92ee_phy_config_mac_with_headerfile(hw);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c
@@ -14,13 +14,6 @@
 #include "hw.h"
 #include "table.h"
 
-static u32 _rtl92s_phy_calculate_bit_shift(u32 bitmask)
-{
-	u32 i = ffs(bitmask);
-
-	return i ? i - 1 : 32;
-}
-
 u32 rtl92s_phy_query_bb_reg(struct ieee80211_hw *hw, u32 regaddr, u32 bitmask)
 {
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
@@ -30,7 +23,7 @@
 		regaddr, bitmask);
 
 	originalvalue = rtl_read_dword(rtlpriv, regaddr);
-	bitshift = _rtl92s_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	returnvalue = (originalvalue & bitmask) >> bitshift;
 
 	rtl_dbg(rtlpriv, COMP_RF, DBG_TRACE, "BBR MASK=0x%x Addr[0x%x]=0x%x\n",
@@ -52,7 +45,7 @@
 
 	if (bitmask != MASKDWORD) {
 		originalvalue = rtl_read_dword(rtlpriv, regaddr);
-		bitshift = _rtl92s_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = ((originalvalue & (~bitmask)) | (data << bitshift));
 	}
 
@@ -160,7 +153,7 @@
 
 	original_value = _rtl92s_phy_rf_serial_read(hw, rfpath, regaddr);
 
-	bitshift = _rtl92s_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 
 	spin_unlock(&rtlpriv->locks.rf_lock);
@@ -191,7 +184,7 @@
 	if (bitmask != RFREG_OFFSET_MASK) {
 		original_value = _rtl92s_phy_rf_serial_read(hw, rfpath,
 							    regaddr);
-		bitshift = _rtl92s_phy_calculate_bit_shift(bitmask);
+		bitshift = calculate_bit_shift(bitmask);
 		data = ((original_value & (~bitmask)) | (data << bitshift));
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8192se/sw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8192se/sw.c
@@ -67,22 +67,23 @@
 
 	rtl_dbg(rtlpriv, COMP_ERR, DBG_LOUD,
 		"Firmware callback routine entered!\n");
-	complete(&rtlpriv->firmware_loading_complete);
 	if (!firmware) {
 		pr_err("Firmware %s not available\n", fw_name);
 		rtlpriv->max_fw_size = 0;
-		return;
+		goto exit;
 	}
 	if (firmware->size > rtlpriv->max_fw_size) {
 		pr_err("Firmware is too big!\n");
 		rtlpriv->max_fw_size = 0;
 		release_firmware(firmware);
-		return;
+		goto exit;
 	}
 	pfirmware = (struct rt_firmware *)rtlpriv->rtlhal.pfirmware;
 	memcpy(pfirmware->sz_fw_tmpbuffer, firmware->data, firmware->size);
 	pfirmware->sz_fw_tmpbufferlen = firmware->size;
 	release_firmware(firmware);
+exit:
+	complete(&rtlpriv->firmware_loading_complete);
 }
 
 static int rtl92s_init_sw_vars(struct ieee80211_hw *hw)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c
@@ -466,7 +466,7 @@
 	}
 
 	if (rtlpriv->btcoexist.bt_edca_dl != 0) {
-		edca_be_ul = rtlpriv->btcoexist.bt_edca_dl;
+		edca_be_dl = rtlpriv->btcoexist.bt_edca_dl;
 		bt_change_edca = true;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c
@@ -49,7 +49,7 @@
 							    rfpath, regaddr);
 	}
 
-	bitshift = rtl8723_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 
 	spin_unlock(&rtlpriv->locks.rf_lock);
@@ -80,7 +80,7 @@
 			original_value = rtl8723_phy_rf_serial_read(hw,
 								    rfpath,
 								    regaddr);
-			bitshift = rtl8723_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
@@ -89,7 +89,7 @@
 		rtl8723_phy_rf_serial_write(hw, rfpath, regaddr, data);
 	} else {
 		if (bitmask != RFREG_OFFSET_MASK) {
-			bitshift = rtl8723_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data =
 			    ((original_value & (~bitmask)) |
 			     (data << bitshift));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8723be/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8723be/hw.c
@@ -30,8 +30,10 @@
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	struct rtl8192_tx_ring *ring = &rtlpci->tx_ring[BEACON_QUEUE];
+	struct sk_buff_head free_list;
 	unsigned long flags;
 
+	skb_queue_head_init(&free_list);
 	spin_lock_irqsave(&rtlpriv->locks.irq_th_lock, flags);
 	while (skb_queue_len(&ring->queue)) {
 		struct rtl_tx_desc *entry = &ring->desc[ring->idx];
@@ -41,10 +43,12 @@
 				 rtlpriv->cfg->ops->get_desc(hw, (u8 *)entry,
 						true, HW_DESC_TXBUFF_ADDR),
 				 skb->len, DMA_TO_DEVICE);
-		kfree_skb(skb);
+		__skb_queue_tail(&free_list, skb);
 		ring->idx = (ring->idx + 1) % ring->entries;
 	}
 	spin_unlock_irqrestore(&rtlpriv->locks.irq_th_lock, flags);
+
+	__skb_queue_purge(&free_list);
 }
 
 static void _rtl8723be_set_bcn_ctrl_reg(struct ieee80211_hw *hw,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c
@@ -41,7 +41,7 @@
 	spin_lock(&rtlpriv->locks.rf_lock);
 
 	original_value = rtl8723_phy_rf_serial_read(hw, rfpath, regaddr);
-	bitshift = rtl8723_phy_calculate_bit_shift(bitmask);
+	bitshift = calculate_bit_shift(bitmask);
 	readback_value = (original_value & bitmask) >> bitshift;
 
 	spin_unlock(&rtlpriv->locks.rf_lock);
@@ -68,7 +68,7 @@
 	if (bitmask != RFREG_OFFSET_MASK) {
 			original_value = rtl8723_phy_rf_serial_read(hw, path,
 								    regaddr);
-			bitshift = rtl8723_phy_calculate_bit_shift(bitmask);
+			bitshift = calculate_bit_shift(bitmask);
 			data = ((original_value & (~bitmask)) |
 				(data << bitshift));
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.h
@@ -197,9 +197,9 @@
 
 /* _MEDIA_STATUS_RPT_PARM_CMD1 */
 #define SET_H2CCMD_MSRRPT_PARM_OPMODE(__cmd, __value)	\
-	u8p_replace_bits(__cmd + 1, __value, BIT(0))
+	u8p_replace_bits(__cmd, __value, BIT(0))
 #define SET_H2CCMD_MSRRPT_PARM_MACID_IND(__cmd, __value)	\
-	u8p_replace_bits(__cmd + 1, __value, BIT(1))
+	u8p_replace_bits(__cmd, __value, BIT(1))
 
 /* AP_OFFLOAD */
 #define SET_H2CCMD_AP_OFFLOAD_ON(__cmd, __value)	\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c
@@ -26,8 +26,10 @@
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	struct rtl8192_tx_ring *ring = &rtlpci->tx_ring[BEACON_QUEUE];
+	struct sk_buff_head free_list;
 	unsigned long flags;
 
+	skb_queue_head_init(&free_list);
 	spin_lock_irqsave(&rtlpriv->locks.irq_th_lock, flags);
 	while (skb_queue_len(&ring->queue)) {
 		struct rtl_tx_desc *entry = &ring->desc[ring->idx];
@@ -37,10 +39,12 @@
 				 rtlpriv->cfg->ops->get_desc(hw, (u8 *)entry,
 						true, HW_DESC_TXBUFF_ADDR),
 				 skb->len, DMA_TO_DEVICE);
-		kfree_skb(skb);
+		__skb_queue_tail(&free_list, skb);
 		ring->idx = (ring->idx + 1) % ring->entries;
 	}
 	spin_unlock_irqrestore(&rtlpriv->locks.irq_th_lock, flags);
+
+	__skb_queue_purge(&free_list);
 }
 
 static void _rtl8821ae_set_bcn_ctrl_reg(struct ieee80211_hw *hw,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c
@@ -29,9 +29,10 @@
 					   u32 data);
 static u32 _rtl8821ae_phy_calculate_bit_shift(u32 bitmask)
 {
-	u32 i = ffs(bitmask);
+	if (WARN_ON_ONCE(!bitmask))
+		return 0;
 
-	return i ? i - 1 : 32;
+	return __ffs(bitmask);
 }
 static bool _rtl8821ae_phy_bb8821a_config_parafile(struct ieee80211_hw *hw);
 /*static bool _rtl8812ae_phy_config_mac_with_headerfile(struct ieee80211_hw *hw);*/
@@ -1598,18 +1599,6 @@
 	return true;
 }
 
-static bool _rtl8812ae_eq_n_byte(const char *str1, const char *str2, u32 num)
-{
-	if (num == 0)
-		return false;
-	while (num > 0) {
-		num--;
-		if (str1[num] != str2[num])
-			return false;
-	}
-	return true;
-}
-
 static s8 _rtl8812ae_phy_get_chnl_idx_of_txpwr_lmt(struct ieee80211_hw *hw,
 					      u8 band, u8 channel)
 {
@@ -1659,42 +1648,42 @@
 	power_limit = power_limit > MAX_POWER_INDEX ?
 		      MAX_POWER_INDEX : power_limit;
 
-	if (_rtl8812ae_eq_n_byte(pregulation, "FCC", 3))
+	if (strcmp(pregulation, "FCC") == 0)
 		regulation = 0;
-	else if (_rtl8812ae_eq_n_byte(pregulation, "MKK", 3))
+	else if (strcmp(pregulation, "MKK") == 0)
 		regulation = 1;
-	else if (_rtl8812ae_eq_n_byte(pregulation, "ETSI", 4))
+	else if (strcmp(pregulation, "ETSI") == 0)
 		regulation = 2;
-	else if (_rtl8812ae_eq_n_byte(pregulation, "WW13", 4))
+	else if (strcmp(pregulation, "WW13") == 0)
 		regulation = 3;
 
-	if (_rtl8812ae_eq_n_byte(prate_section, "CCK", 3))
+	if (strcmp(prate_section, "CCK") == 0)
 		rate_section = 0;
-	else if (_rtl8812ae_eq_n_byte(prate_section, "OFDM", 4))
+	else if (strcmp(prate_section, "OFDM") == 0)
 		rate_section = 1;
-	else if (_rtl8812ae_eq_n_byte(prate_section, "HT", 2) &&
-		 _rtl8812ae_eq_n_byte(prf_path, "1T", 2))
+	else if (strcmp(prate_section, "HT") == 0 &&
+		 strcmp(prf_path, "1T") == 0)
 		rate_section = 2;
-	else if (_rtl8812ae_eq_n_byte(prate_section, "HT", 2) &&
-		 _rtl8812ae_eq_n_byte(prf_path, "2T", 2))
+	else if (strcmp(prate_section, "HT") == 0 &&
+		 strcmp(prf_path, "2T") == 0)
 		rate_section = 3;
-	else if (_rtl8812ae_eq_n_byte(prate_section, "VHT", 3) &&
-		 _rtl8812ae_eq_n_byte(prf_path, "1T", 2))
+	else if (strcmp(prate_section, "VHT") == 0 &&
+		 strcmp(prf_path, "1T") == 0)
 		rate_section = 4;
-	else if (_rtl8812ae_eq_n_byte(prate_section, "VHT", 3) &&
-		 _rtl8812ae_eq_n_byte(prf_path, "2T", 2))
+	else if (strcmp(prate_section, "VHT") == 0 &&
+		 strcmp(prf_path, "2T") == 0)
 		rate_section = 5;
 
-	if (_rtl8812ae_eq_n_byte(pbandwidth, "20M", 3))
+	if (strcmp(pbandwidth, "20M") == 0)
 		bandwidth = 0;
-	else if (_rtl8812ae_eq_n_byte(pbandwidth, "40M", 3))
+	else if (strcmp(pbandwidth, "40M") == 0)
 		bandwidth = 1;
-	else if (_rtl8812ae_eq_n_byte(pbandwidth, "80M", 3))
+	else if (strcmp(pbandwidth, "80M") == 0)
 		bandwidth = 2;
-	else if (_rtl8812ae_eq_n_byte(pbandwidth, "160M", 4))
+	else if (strcmp(pbandwidth, "160M") == 0)
 		bandwidth = 3;
 
-	if (_rtl8812ae_eq_n_byte(pband, "2.4G", 4)) {
+	if (strcmp(pband, "2.4G") == 0) {
 		ret = _rtl8812ae_phy_get_chnl_idx_of_txpwr_lmt(hw,
 							       BAND_ON_2_4G,
 							       channel);
@@ -1718,7 +1707,7 @@
 			regulation, bandwidth, rate_section, channel_index,
 			rtlphy->txpwr_limit_2_4g[regulation][bandwidth]
 				[rate_section][channel_index][RF90_PATH_A]);
-	} else if (_rtl8812ae_eq_n_byte(pband, "5G", 2)) {
+	} else if (strcmp(pband, "5G") == 0) {
 		ret = _rtl8812ae_phy_get_chnl_idx_of_txpwr_lmt(hw,
 							       BAND_ON_5G,
 							       channel);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/usb.c
@@ -679,11 +679,6 @@
 	tasklet_kill(&rtlusb->rx_work_tasklet);
 	cancel_work_sync(&rtlpriv->works.lps_change_work);
 
-	if (rtlpriv->works.rtl_wq) {
-		destroy_workqueue(rtlpriv->works.rtl_wq);
-		rtlpriv->works.rtl_wq = NULL;
-	}
-
 	skb_queue_purge(&rtlusb->rx_queue);
 
 	while ((urb = usb_get_from_anchor(&rtlusb->rx_cleanup_urbs))) {
@@ -1014,7 +1009,7 @@
 	hw = ieee80211_alloc_hw(sizeof(struct rtl_priv) +
 				sizeof(struct rtl_usb_priv), &rtl_ops);
 	if (!hw) {
-		WARN_ONCE(true, "rtl_usb: ieee80211 alloc failed\n");
+		pr_warn("rtl_usb: ieee80211 alloc failed\n");
 		return -ENOMEM;
 	}
 	rtlpriv = hw->priv;
@@ -1073,19 +1068,22 @@
 	err = ieee80211_register_hw(hw);
 	if (err) {
 		pr_err("Can't register mac80211 hw.\n");
-		goto error_out;
+		goto error_init_vars;
 	}
 	rtlpriv->mac80211.mac80211_registered = 1;
 
 	set_bit(RTL_STATUS_INTERFACE_START, &rtlpriv->status);
 	return 0;
 
+error_init_vars:
+	wait_for_completion(&rtlpriv->firmware_loading_complete);
+	rtlpriv->cfg->ops->deinit_sw_vars(hw);
 error_out:
+	rtl_usb_deinit(hw);
 	rtl_deinit_core(hw);
 error_out2:
 	_rtl_usb_io_handler_release(hw);
 	usb_put_dev(udev);
-	complete(&rtlpriv->firmware_loading_complete);
 	kfree(rtlpriv->usb_data);
 	ieee80211_free_hw(hw);
 	return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtlwifi/wifi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtlwifi/wifi.h
@@ -108,7 +108,6 @@
 #define	CHANNEL_GROUP_IDX_5GM		6
 #define	CHANNEL_GROUP_IDX_5GH		9
 #define	CHANNEL_GROUP_MAX_5G		9
-#define CHANNEL_MAX_NUMBER_2G		14
 #define AVG_THERMAL_NUM			8
 #define AVG_THERMAL_NUM_88E		4
 #define AVG_THERMAL_NUM_8723BE		4
@@ -2301,7 +2300,6 @@
 			  u32 regaddr, u32 bitmask, u32 data);
 	void (*linked_set_reg)(struct ieee80211_hw *hw);
 	void (*chk_switch_dmdp)(struct ieee80211_hw *hw);
-	void (*dualmac_easy_concurrent)(struct ieee80211_hw *hw);
 	void (*dualmac_switch_to_dmdp)(struct ieee80211_hw *hw);
 	bool (*phy_rf6052_config)(struct ieee80211_hw *hw);
 	void (*phy_rf6052_set_cck_txpower)(struct ieee80211_hw *hw,
@@ -2337,8 +2335,6 @@
 	void (*read_efuse_byte)(struct ieee80211_hw *hw, u16 _offset, u8 *pbuf);
 	int (*adapter_start)(struct ieee80211_hw *hw);
 	void (*adapter_stop)(struct ieee80211_hw *hw);
-	bool (*check_buddy_priv)(struct ieee80211_hw *hw,
-				 struct rtl_priv **buddy_priv);
 
 	int (*adapter_tx)(struct ieee80211_hw *hw,
 			  struct ieee80211_sta *sta,
@@ -2466,7 +2462,6 @@
 
 	/*timer */
 	struct timer_list watchdog_timer;
-	struct timer_list dualmac_easyconcurrent_retrytimer;
 	struct timer_list fw_clockoff_timer;
 	struct timer_list fast_antenna_training_timer;
 	/*task */
@@ -2499,14 +2494,6 @@
 #define MIMO_PS_DYNAMIC			1
 #define MIMO_PS_NOLIMIT			3
 
-struct rtl_dualmac_easy_concurrent_ctl {
-	enum band_type currentbandtype_backfordmdp;
-	bool close_bbandrf_for_dmsp;
-	bool change_to_dmdp;
-	bool change_to_dmsp;
-	bool switch_in_process;
-};
-
 struct rtl_dmsp_ctl {
 	bool activescan_for_slaveofdmsp;
 	bool scan_for_anothermac_fordmsp;
@@ -2591,14 +2578,6 @@
 	u32 rssi_max;
 };
 
-struct rtl_global_var {
-	/* from this list we can get
-	 * other adapter's rtl_priv
-	 */
-	struct list_head glb_priv_list;
-	spinlock_t glb_list_lock;
-};
-
 #define IN_4WAY_TIMEOUT_TIME	(30 * MSEC_PER_SEC)	/* 30 seconds */
 
 struct rtl_btc_info {
@@ -2744,10 +2723,7 @@
 struct rtl_priv {
 	struct ieee80211_hw *hw;
 	struct completion firmware_loading_complete;
-	struct list_head list;
 	struct rtl_priv *buddy_priv;
-	struct rtl_global_var *glb_var;
-	struct rtl_dualmac_easy_concurrent_ctl easy_concurrent_ctl;
 	struct rtl_dmsp_ctl dmsp_ctl;
 	struct rtl_locks locks;
 	struct rtl_works works;
@@ -3106,4 +3082,11 @@
 	return ieee80211_find_sta(mac->vif, mac_addr);
 }
 
+static inline u32 calculate_bit_shift(u32 bitmask)
+{
+	if (WARN_ON_ONCE(!bitmask))
+		return 0;
+
+	return __ffs(bitmask);
+}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/Kconfig
@@ -12,6 +12,7 @@
 
 config RTW88_CORE
 	tristate
+	select WANT_DEV_COREDUMP
 
 config RTW88_PCI
 	tristate
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/coex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/coex.c
@@ -2103,7 +2103,6 @@
 	struct rtw_efuse *efuse = &rtwdev->efuse;
 	struct rtw_chip_info *chip = rtwdev->chip;
 	u8 table_case, tdma_case;
-	bool wl_cpt_test = false, bt_cpt_test = false;
 
 	rtw_dbg(rtwdev, RTW_DBG_COEX, "[BTCoex], %s()\n", __func__);
 
@@ -2111,29 +2110,16 @@
 	rtw_coex_set_rf_para(rtwdev, chip->wl_rf_para_rx[0]);
 	if (efuse->share_ant) {
 		/* Shared-Ant */
-		if (wl_cpt_test) {
-			if (coex_stat->wl_gl_busy) {
-				table_case = 20;
-				tdma_case = 17;
-			} else {
-				table_case = 10;
-				tdma_case = 15;
-			}
-		} else if (bt_cpt_test) {
-			table_case = 26;
-			tdma_case = 26;
-		} else {
-			if (coex_stat->wl_gl_busy &&
-			    coex_stat->wl_noisy_level == 0)
-				table_case = 14;
-			else
-				table_case = 10;
+		if (coex_stat->wl_gl_busy &&
+		    coex_stat->wl_noisy_level == 0)
+			table_case = 14;
+		else
+			table_case = 10;
 
-			if (coex_stat->wl_gl_busy)
-				tdma_case = 15;
-			else
-				tdma_case = 20;
-		}
+		if (coex_stat->wl_gl_busy)
+			tdma_case = 15;
+		else
+			tdma_case = 20;
 	} else {
 		/* Non-Shared-Ant */
 		table_case = 112;
@@ -2144,11 +2130,7 @@
 			tdma_case = 120;
 	}
 
-	if (wl_cpt_test)
-		rtw_coex_set_rf_para(rtwdev, chip->wl_rf_para_rx[1]);
-	else
-		rtw_coex_set_rf_para(rtwdev, chip->wl_rf_para_rx[0]);
-
+	rtw_coex_set_rf_para(rtwdev, chip->wl_rf_para_rx[0]);
 	rtw_coex_table(rtwdev, false, table_case);
 	rtw_coex_tdma(rtwdev, false, tdma_case);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/debug.c
@@ -1061,9 +1061,9 @@
 #define rtw_debugfs_add_core(name, mode, fopname, parent)		\
 	do {								\
 		rtw_debug_priv_ ##name.rtwdev = rtwdev;			\
-		if (!debugfs_create_file(#name, mode,			\
+		if (IS_ERR(debugfs_create_file(#name, mode,		\
 					 parent, &rtw_debug_priv_ ##name,\
-					 &file_ops_ ##fopname))		\
+					 &file_ops_ ##fopname)))	\
 			pr_debug("Unable to initialize debugfs:%s\n",	\
 			       #name);					\
 	} while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/fw.c
@@ -541,7 +541,6 @@
 void rtw_fw_send_ra_info(struct rtw_dev *rtwdev, struct rtw_sta_info *si)
 {
 	u8 h2c_pkt[H2C_PKT_SIZE] = {0};
-	bool no_update = si->updated;
 	bool disable_pt = true;
 
 	SET_H2C_CMD_ID_CLASS(h2c_pkt, H2C_CMD_RA_INFO);
@@ -552,7 +551,7 @@
 	SET_RA_INFO_SGI_EN(h2c_pkt, si->sgi_enable);
 	SET_RA_INFO_BW_MODE(h2c_pkt, si->bw_mode);
 	SET_RA_INFO_LDPC(h2c_pkt, !!si->ldpc_en);
-	SET_RA_INFO_NO_UPDATE(h2c_pkt, no_update);
+	SET_RA_INFO_NO_UPDATE(h2c_pkt, si->no_update);
 	SET_RA_INFO_VHT_EN(h2c_pkt, si->vht_enable);
 	SET_RA_INFO_DIS_PT(h2c_pkt, disable_pt);
 	SET_RA_INFO_RA_MASK0(h2c_pkt, (si->ra_mask & 0xff));
@@ -561,7 +560,6 @@
 	SET_RA_INFO_RA_MASK3(h2c_pkt, (si->ra_mask & 0xff000000) >> 24);
 
 	si->init_ra_lv = 0;
-	si->updated = true;
 
 	rtw_fw_send_h2c_command(rtwdev, h2c_pkt);
 }
@@ -1001,6 +999,7 @@
 	struct rtw_vif *rtwvif;
 	struct sk_buff *skb_new;
 	struct cfg80211_ssid *ssid;
+	u16 tim_offset;
 
 	if (rsvd_pkt->type == RSVD_DUMMY) {
 		skb_new = alloc_skb(1, GFP_KERNEL);
@@ -1019,7 +1018,8 @@
 
 	switch (rsvd_pkt->type) {
 	case RSVD_BEACON:
-		skb_new = ieee80211_beacon_get(hw, vif);
+		skb_new = ieee80211_beacon_get_tim(hw, vif, &tim_offset, NULL);
+		rsvd_pkt->tim_offset = tim_offset;
 		break;
 	case RSVD_PS_POLL:
 		skb_new = ieee80211_pspoll_get(hw, vif);
@@ -1556,12 +1556,10 @@
 	u32 i;
 	u16 idx = 0;
 	u16 ctl;
-	u8 rcr;
 
-	rcr = rtw_read8(rtwdev, REG_RCR + 2);
 	ctl = rtw_read16(rtwdev, REG_PKTBUF_DBG_CTRL) & 0xf000;
 	/* disable rx clock gate */
-	rtw_write8(rtwdev, REG_RCR, rcr | BIT(3));
+	rtw_write32_set(rtwdev, REG_RCR, BIT_DISGCLK);
 
 	do {
 		rtw_write16(rtwdev, REG_PKTBUF_DBG_CTRL, start_pg | ctl);
@@ -1580,7 +1578,8 @@
 
 out:
 	rtw_write16(rtwdev, REG_PKTBUF_DBG_CTRL, ctl);
-	rtw_write8(rtwdev, REG_RCR + 2, rcr);
+	/* restore rx clock gate */
+	rtw_write32_clr(rtwdev, REG_RCR, BIT_DISGCLK);
 }
 
 static void rtw_fw_read_fifo(struct rtw_dev *rtwdev, enum rtw_fw_fifo_sel sel,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/fw.h
@@ -145,6 +145,7 @@
 	struct sk_buff *skb;
 	enum rtw_rsvd_packet_type type;
 	u8 page;
+	u16 tim_offset;
 	bool add_txdesc;
 	struct cfg80211_ssid *ssid;
 	u16 probe_req_size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/mac.c
@@ -233,7 +233,7 @@
 
 		ret = rtw_sub_pwr_seq_parser(rtwdev, intf_mask, cut_mask, cmd);
 		if (ret)
-			return -EBUSY;
+			return ret;
 
 		idx++;
 	} while (1);
@@ -247,6 +247,7 @@
 	const struct rtw_pwr_seq_cmd **pwr_seq;
 	u8 rpwm;
 	bool cur_pwr;
+	int ret;
 
 	if (rtw_chip_wcpu_11ac(rtwdev)) {
 		rpwm = rtw_read8(rtwdev, rtwdev->hci.rpwm_addr);
@@ -270,8 +271,9 @@
 		return -EALREADY;
 
 	pwr_seq = pwr_on ? chip->pwr_on_seq : chip->pwr_off_seq;
-	if (rtw_pwr_seq_parser(rtwdev, pwr_seq))
-		return -EINVAL;
+	ret = rtw_pwr_seq_parser(rtwdev, pwr_seq);
+	if (ret)
+		return ret;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/mac80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/mac80211.c
@@ -267,9 +267,9 @@
 
 	if (changed_flags & FIF_ALLMULTI) {
 		if (*new_flags & FIF_ALLMULTI)
-			rtwdev->hal.rcr |= BIT_AM | BIT_AB;
+			rtwdev->hal.rcr |= BIT_AM;
 		else
-			rtwdev->hal.rcr &= ~(BIT_AM | BIT_AB);
+			rtwdev->hal.rcr &= ~(BIT_AM);
 	}
 	if (changed_flags & FIF_FCSFAIL) {
 		if (*new_flags & FIF_FCSFAIL)
@@ -391,8 +391,10 @@
 			coex_stat->wl_beacon_interval = conf->beacon_int;
 	}
 
-	if (changed & BSS_CHANGED_BEACON)
+	if (changed & BSS_CHANGED_BEACON) {
+		rtw_set_dtim_period(rtwdev, conf->dtim_period);
 		rtw_fw_download_rsvd_page(rtwdev);
+	}
 
 	if (changed & BSS_CHANGED_BEACON_ENABLED) {
 		if (conf->enable_beacon)
@@ -416,6 +418,18 @@
 	mutex_unlock(&rtwdev->mutex);
 }
 
+static int rtw_ops_start_ap(struct ieee80211_hw *hw, struct ieee80211_vif *vif)
+{
+	struct rtw_dev *rtwdev = hw->priv;
+	struct rtw_chip_info *chip = rtwdev->chip;
+
+	mutex_lock(&rtwdev->mutex);
+	chip->ops->phy_calibration(rtwdev);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
 static int rtw_ops_conf_tx(struct ieee80211_hw *hw,
 			   struct ieee80211_vif *vif, u16 ac,
 			   const struct ieee80211_tx_queue_params *params)
@@ -463,6 +477,18 @@
 	return 0;
 }
 
+static int rtw_ops_set_tim(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
+			   bool set)
+{
+	struct rtw_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw_fw_download_rsvd_page(rtwdev);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
 static int rtw_ops_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 			   struct ieee80211_vif *vif, struct ieee80211_sta *sta,
 			   struct ieee80211_key_conf *key)
@@ -709,7 +735,7 @@
 	}
 
 	si->use_cfg_mask = true;
-	rtw_update_sta_info(br_data->rtwdev, si);
+	rtw_update_sta_info(br_data->rtwdev, si, true);
 }
 
 static void rtw_ra_mask_info_update(struct rtw_dev *rtwdev,
@@ -815,6 +841,17 @@
 	mutex_unlock(&rtwdev->mutex);
 }
 
+static void rtw_ops_sta_rc_update(struct ieee80211_hw *hw,
+				  struct ieee80211_vif *vif,
+				  struct ieee80211_sta *sta, u32 changed)
+{
+	struct rtw_dev *rtwdev = hw->priv;
+	struct rtw_sta_info *si = (struct rtw_sta_info *)sta->drv_priv;
+
+	if (changed & IEEE80211_RC_BW_CHANGED)
+		rtw_update_sta_info(rtwdev, si, true);
+}
+
 const struct ieee80211_ops rtw_ops = {
 	.tx			= rtw_ops_tx,
 	.wake_tx_queue		= rtw_ops_wake_tx_queue,
@@ -826,9 +863,11 @@
 	.change_interface	= rtw_ops_change_interface,
 	.configure_filter	= rtw_ops_configure_filter,
 	.bss_info_changed	= rtw_ops_bss_info_changed,
+	.start_ap		= rtw_ops_start_ap,
 	.conf_tx		= rtw_ops_conf_tx,
 	.sta_add		= rtw_ops_sta_add,
 	.sta_remove		= rtw_ops_sta_remove,
+	.set_tim		= rtw_ops_set_tim,
 	.set_key		= rtw_ops_set_key,
 	.ampdu_action		= rtw_ops_ampdu_action,
 	.can_aggregate_in_amsdu	= rtw_ops_can_aggregate_in_amsdu,
@@ -842,6 +881,7 @@
 	.set_antenna		= rtw_ops_set_antenna,
 	.get_antenna		= rtw_ops_get_antenna,
 	.reconfig_complete	= rtw_reconfig_complete,
+	.sta_rc_update		= rtw_ops_sta_rc_update,
 #ifdef CONFIG_PM
 	.suspend		= rtw_ops_suspend,
 	.resume			= rtw_ops_resume,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/main.c
@@ -291,7 +291,7 @@
 	for (i = 0; i < ARRAY_SIZE(sta->txq); i++)
 		rtw_txq_init(rtwdev, sta->txq[i]);
 
-	rtw_update_sta_info(rtwdev, si);
+	rtw_update_sta_info(rtwdev, si, true);
 	rtw_fw_media_status_report(rtwdev, si->mac_id, true);
 
 	rtwdev->sta_cnt++;
@@ -628,6 +628,12 @@
 	rtw_iterate_stas_atomic(rtwdev, rtw_txq_ba_iter, &data);
 }
 
+void rtw_set_dtim_period(struct rtw_dev *rtwdev, int dtim_period)
+{
+	rtw_write32_set(rtwdev, REG_TCR, BIT_TCR_UPDATE_TIMIE);
+	rtw_write8(rtwdev, REG_DTIM_COUNTER_ROOT, dtim_period - 1);
+}
+
 void rtw_get_channel_params(struct cfg80211_chan_def *chandef,
 			    struct rtw_channel_params *chan_params)
 {
@@ -1034,7 +1040,8 @@
 	return ra_mask;
 }
 
-void rtw_update_sta_info(struct rtw_dev *rtwdev, struct rtw_sta_info *si)
+void rtw_update_sta_info(struct rtw_dev *rtwdev, struct rtw_sta_info *si,
+			 bool update)
 {
 	struct rtw_dm_info *dm_info = &rtwdev->dm_info;
 	struct ieee80211_sta *sta = si->sta;
@@ -1136,6 +1143,7 @@
 	ra_mask = rtw_update_rate_mask(rtwdev, si, ra_mask, is_vht_enable,
 				       wireless_set);
 
+	si->no_update = !update;
 	si->bw_mode = bw_mode;
 	si->stbc_en = stbc_en;
 	si->ldpc_en = ldpc_en;
@@ -1153,20 +1161,21 @@
 {
 	struct rtw_chip_info *chip = rtwdev->chip;
 	struct rtw_fw_state *fw;
+	int ret = 0;
 
 	fw = &rtwdev->fw;
 	wait_for_completion(&fw->completion);
 	if (!fw->firmware)
-		return -EINVAL;
+		ret = -EINVAL;
 
 	if (chip->wow_fw_name) {
 		fw = &rtwdev->wow_fw;
 		wait_for_completion(&fw->completion);
 		if (!fw->firmware)
-			return -EINVAL;
+			ret = -EINVAL;
 	}
 
-	return 0;
+	return ret;
 }
 
 static enum rtw_lps_deep_mode rtw_update_lps_deep_mode(struct rtw_dev *rtwdev,
@@ -1819,6 +1828,10 @@
 	timer_setup(&rtwdev->tx_report.purge_timer,
 		    rtw_tx_report_purge_timer, 0);
 	rtwdev->tx_wq = alloc_workqueue("rtw_tx_wq", WQ_UNBOUND | WQ_HIGHPRI, 0);
+	if (!rtwdev->tx_wq) {
+		rtw_warn(rtwdev, "alloc_workqueue rtw_tx_wq failed\n");
+		return -ENOMEM;
+	}
 
 	INIT_DELAYED_WORK(&rtwdev->watch_dog_work, rtw_watch_dog_work);
 	INIT_DELAYED_WORK(&coex->bt_relink_work, rtw_coex_bt_relink_work);
@@ -1859,13 +1872,13 @@
 
 	/* default rx filter setting */
 	rtwdev->hal.rcr = BIT_APP_FCS | BIT_APP_MIC | BIT_APP_ICV |
-			  BIT_HTC_LOC_CTRL | BIT_APP_PHYSTS |
+			  BIT_PKTCTL_DLEN | BIT_HTC_LOC_CTRL | BIT_APP_PHYSTS |
 			  BIT_AB | BIT_AM | BIT_APM;
 
 	ret = rtw_load_firmware(rtwdev, RTW_NORMAL_FW);
 	if (ret) {
 		rtw_warn(rtwdev, "no firmware loaded\n");
-		return ret;
+		goto out;
 	}
 
 	if (chip->wow_fw_name) {
@@ -1875,11 +1888,15 @@
 			wait_for_completion(&rtwdev->fw.completion);
 			if (rtwdev->fw.firmware)
 				release_firmware(rtwdev->fw.firmware);
-			return ret;
+			goto out;
 		}
 	}
 
 	return 0;
+
+out:
+	destroy_workqueue(rtwdev->tx_wq);
+	return ret;
 }
 EXPORT_SYMBOL(rtw_core_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/main.h
@@ -571,6 +571,7 @@
 	u32 tx_pkt_size;
 	u8 offset;
 	u8 pkt_offset;
+	u8 tim_offset;
 	u8 mac_id;
 	u8 rate_id;
 	u8 rate;
@@ -742,7 +743,7 @@
 	u8 ldpc_en:2;
 	bool sgi_enable;
 	bool vht_enable;
-	bool updated;
+	bool no_update;
 	u8 init_ra_lv;
 	u64 ra_mask;
 
@@ -1981,6 +1982,7 @@
 void rtw_get_channel_params(struct cfg80211_chan_def *chandef,
 			    struct rtw_channel_params *ch_param);
 bool check_hw_ready(struct rtw_dev *rtwdev, u32 addr, u32 mask, u32 target);
+void rtw_set_dtim_period(struct rtw_dev *rtwdev, int dtim_period);
 bool ltecoex_read_reg(struct rtw_dev *rtwdev, u16 offset, u32 *val);
 bool ltecoex_reg_write(struct rtw_dev *rtwdev, u16 offset, u32 value);
 void rtw_restore_reg(struct rtw_dev *rtwdev,
@@ -1991,7 +1993,8 @@
 void rtw_vif_port_config(struct rtw_dev *rtwdev, struct rtw_vif *rtwvif,
 			 u32 config);
 void rtw_tx_report_purge_timer(struct timer_list *t);
-void rtw_update_sta_info(struct rtw_dev *rtwdev, struct rtw_sta_info *si);
+void rtw_update_sta_info(struct rtw_dev *rtwdev, struct rtw_sta_info *si,
+			 bool update);
 int rtw_core_start(struct rtw_dev *rtwdev);
 void rtw_core_stop(struct rtw_dev *rtwdev);
 int rtw_chip_info_setup(struct rtw_dev *rtwdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/pci.c
@@ -2,7 +2,6 @@
 /* Copyright(c) 2018-2019  Realtek Corporation
  */
 
-#include <linux/dmi.h>
 #include <linux/module.h>
 #include <linux/pci.h>
 #include "main.h"
@@ -687,6 +686,9 @@
 		queue = RTW_TX_QUEUE_BCN;
 	else if (unlikely(ieee80211_is_mgmt(fc) || ieee80211_is_ctl(fc)))
 		queue = RTW_TX_QUEUE_MGMT;
+	else if (is_broadcast_ether_addr(hdr->addr1) ||
+		 is_multicast_ether_addr(hdr->addr1))
+		queue = RTW_TX_QUEUE_HI0;
 	else if (WARN_ON_ONCE(q_mapping >= ARRAY_SIZE(ac_to_hwq)))
 		queue = ac_to_hwq[IEEE80211_AC_BE];
 	else
@@ -1409,7 +1411,11 @@
 	 * throughput. This is probably because the ASPM behavior slightly
 	 * varies from different SOC.
 	 */
-	if (rtwpci->link_ctrl & PCI_EXP_LNKCTL_ASPM_L1)
+	if (!(rtwpci->link_ctrl & PCI_EXP_LNKCTL_ASPM_L1))
+		return;
+
+	if ((enter && atomic_dec_if_positive(&rtwpci->link_usage) == 0) ||
+	    (!enter && atomic_inc_return(&rtwpci->link_usage) == 1))
 		rtw_pci_aspm_set(rtwdev, enter);
 }
 
@@ -1472,12 +1478,15 @@
 
 static void rtw_pci_phy_cfg(struct rtw_dev *rtwdev)
 {
+	struct rtw_pci *rtwpci = (struct rtw_pci *)rtwdev->priv;
 	struct rtw_chip_info *chip = rtwdev->chip;
+	struct pci_dev *pdev = rtwpci->pdev;
 	const struct rtw_intf_phy_para *para;
 	u16 cut;
 	u16 value;
 	u16 offset;
 	int i;
+	int ret;
 
 	cut = BIT(0) << rtwdev->hal.cut_version;
 
@@ -1510,6 +1519,15 @@
 	}
 
 	rtw_pci_link_cfg(rtwdev);
+
+	/* Disable 8821ce completion timeout by default */
+	if (chip->id == RTW_CHIP_TYPE_8821C) {
+		ret = pcie_capability_set_word(pdev, PCI_EXP_DEVCTL2,
+					       PCI_EXP_DEVCTL2_COMP_TMOUT_DIS);
+		if (ret)
+			rtw_err(rtwdev, "failed to set PCI cap, ret = %d\n",
+				ret);
+	}
 }
 
 static int __maybe_unused rtw_pci_suspend(struct device *dev)
@@ -1658,6 +1676,9 @@
 					      priv);
 	int work_done = 0;
 
+	if (rtwpci->rx_no_aspm)
+		rtw_pci_link_ps(rtwdev, false);
+
 	while (work_done < budget) {
 		u32 work_done_once;
 
@@ -1681,6 +1702,8 @@
 		if (rtw_pci_get_hw_rx_ring_nr(rtwdev, rtwpci))
 			napi_schedule(napi);
 	}
+	if (rtwpci->rx_no_aspm)
+		rtw_pci_link_ps(rtwdev, true);
 
 	return work_done;
 }
@@ -1702,50 +1725,13 @@
 	netif_napi_del(&rtwpci->napi);
 }
 
-enum rtw88_quirk_dis_pci_caps {
-	QUIRK_DIS_PCI_CAP_MSI,
-	QUIRK_DIS_PCI_CAP_ASPM,
-};
-
-static int disable_pci_caps(const struct dmi_system_id *dmi)
-{
-	uintptr_t dis_caps = (uintptr_t)dmi->driver_data;
-
-	if (dis_caps & BIT(QUIRK_DIS_PCI_CAP_MSI))
-		rtw_disable_msi = true;
-	if (dis_caps & BIT(QUIRK_DIS_PCI_CAP_ASPM))
-		rtw_pci_disable_aspm = true;
-
-	return 1;
-}
-
-static const struct dmi_system_id rtw88_pci_quirks[] = {
-	{
-		.callback = disable_pci_caps,
-		.ident = "Protempo Ltd L116HTN6SPW",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "Protempo Ltd"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "L116HTN6SPW"),
-		},
-		.driver_data = (void *)BIT(QUIRK_DIS_PCI_CAP_ASPM),
-	},
-	{
-		.callback = disable_pci_caps,
-		.ident = "HP HP Pavilion Laptop 14-ce0xxx",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "HP"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion Laptop 14-ce0xxx"),
-		},
-		.driver_data = (void *)BIT(QUIRK_DIS_PCI_CAP_ASPM),
-	},
-	{}
-};
-
 int rtw_pci_probe(struct pci_dev *pdev,
 		  const struct pci_device_id *id)
 {
+	struct pci_dev *bridge = pci_upstream_bridge(pdev);
 	struct ieee80211_hw *hw;
 	struct rtw_dev *rtwdev;
+	struct rtw_pci *rtwpci;
 	int drv_data_size;
 	int ret;
 
@@ -1763,6 +1749,9 @@
 	rtwdev->hci.ops = &rtw_pci_ops;
 	rtwdev->hci.type = RTW_HCI_TYPE_PCIE;
 
+	rtwpci = (struct rtw_pci *)rtwdev->priv;
+	atomic_set(&rtwpci->link_usage, 1);
+
 	ret = rtw_core_init(rtwdev);
 	if (ret)
 		goto err_release_hw;
@@ -1791,7 +1780,10 @@
 		goto err_destroy_pci;
 	}
 
-	dmi_check_system(rtw88_pci_quirks);
+	/* Disable PCIe ASPM L1 while doing NAPI poll for 8821CE */
+	if (pdev->device == 0xc821 && bridge->vendor == PCI_VENDOR_ID_INTEL)
+		rtwpci->rx_no_aspm = true;
+
 	rtw_pci_phy_cfg(rtwdev);
 
 	ret = rtw_register_hw(rtwdev, hw);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/pci.h
@@ -223,6 +223,8 @@
 	struct rtw_pci_tx_ring tx_rings[RTK_MAX_TX_QUEUE_NUM];
 	struct rtw_pci_rx_ring rx_rings[RTK_MAX_RX_QUEUE_NUM];
 	u16 link_ctrl;
+	atomic_t link_usage;
+	bool rx_no_aspm;
 	DECLARE_BITMAP(flags, NUM_OF_RTW_PCI_FLAGS);
 
 	void __iomem *mmap;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/phy.c
@@ -476,7 +476,7 @@
 	struct rtw_dev *rtwdev = data;
 	struct rtw_sta_info *si = (struct rtw_sta_info *)sta->drv_priv;
 
-	rtw_update_sta_info(rtwdev, si);
+	rtw_update_sta_info(rtwdev, si, false);
 }
 
 static void rtw_phy_ra_info_update(struct rtw_dev *rtwdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/reg.h
@@ -387,12 +387,14 @@
 #define BIT_EN_FREE_CNT		BIT(3)
 #define BIT_DIS_SECOND_CCA	(BIT(0) | BIT(1))
 #define REG_HIQ_NO_LMT_EN	0x5A7
+#define REG_DTIM_COUNTER_ROOT	0x5A8
 #define BIT_HIQ_NO_LMT_EN_ROOT	BIT(0)
 #define REG_TIMER0_SRC_SEL	0x05B4
 #define BIT_TSFT_SEL_TIMER0	(BIT(4) | BIT(5) | BIT(6))
 
 #define REG_TCR			0x0604
 #define BIT_PWRMGT_HWDATA_EN	BIT(7)
+#define BIT_TCR_UPDATE_TIMIE	BIT(5)
 #define REG_RCR			0x0608
 #define BIT_APP_FCS		BIT(31)
 #define BIT_APP_MIC		BIT(30)
@@ -406,6 +408,7 @@
 #define BIT_MFBEN		BIT(22)
 #define BIT_DISCHKPPDLLEN	BIT(21)
 #define BIT_PKTCTL_DLEN		BIT(20)
+#define BIT_DISGCLK		BIT(19)
 #define BIT_TIM_PARSER_EN	BIT(18)
 #define BIT_BC_MD_EN		BIT(17)
 #define BIT_UC_MD_EN		BIT(16)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/rtw8821c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/rtw8821c.c
@@ -40,7 +40,7 @@
 
 	map = (struct rtw8821c_efuse *)log_map;
 
-	efuse->rfe_option = map->rfe_option;
+	efuse->rfe_option = map->rfe_option & 0x1f;
 	efuse->rf_board_option = map->rf_board_option;
 	efuse->crystal_cap = map->xtal_k;
 	efuse->pa_type_2g = map->pa_type;
@@ -304,7 +304,8 @@
 	if (channel <= 14) {
 		if (rtwdev->efuse.rfe_option == 0)
 			rtw8821c_switch_rf_set(rtwdev, SWITCH_TO_WLG);
-		else if (rtwdev->efuse.rfe_option == 2)
+		else if (rtwdev->efuse.rfe_option == 2 ||
+			 rtwdev->efuse.rfe_option == 4)
 			rtw8821c_switch_rf_set(rtwdev, SWITCH_TO_BTG);
 		rtw_write_rf(rtwdev, RF_PATH_A, RF_LUTDBG, BIT(6), 0x1);
 		rtw_write_rf(rtwdev, RF_PATH_A, 0x64, 0xf, 0xf);
@@ -506,6 +507,7 @@
 static void query_phy_status_page0(struct rtw_dev *rtwdev, u8 *phy_status,
 				   struct rtw_rx_pkt_stat *pkt_stat)
 {
+	struct rtw_dm_info *dm_info = &rtwdev->dm_info;
 	s8 rx_power;
 	u8 lna_idx = 0;
 	u8 vga_idx = 0;
@@ -517,6 +519,7 @@
 
 	pkt_stat->rx_power[RF_PATH_A] = rx_power;
 	pkt_stat->rssi = rtw_phy_rf_power_2_rssi(pkt_stat->rx_power, 1);
+	dm_info->rssi[RF_PATH_A] = pkt_stat->rssi;
 	pkt_stat->bw = RTW_CHANNEL_WIDTH_20;
 	pkt_stat->signal_power = rx_power;
 }
@@ -524,6 +527,7 @@
 static void query_phy_status_page1(struct rtw_dev *rtwdev, u8 *phy_status,
 				   struct rtw_rx_pkt_stat *pkt_stat)
 {
+	struct rtw_dm_info *dm_info = &rtwdev->dm_info;
 	u8 rxsc, bw;
 	s8 min_rx_power = -120;
 
@@ -543,6 +547,7 @@
 
 	pkt_stat->rx_power[RF_PATH_A] = GET_PHY_STAT_P1_PWDB_A(phy_status) - 110;
 	pkt_stat->rssi = rtw_phy_rf_power_2_rssi(pkt_stat->rx_power, 1);
+	dm_info->rssi[RF_PATH_A] = pkt_stat->rssi;
 	pkt_stat->bw = bw;
 	pkt_stat->signal_power = max(pkt_stat->rx_power[RF_PATH_A],
 				     min_rx_power);
@@ -662,9 +667,9 @@
 
 	dm_info->cck_fa_cnt = cck_fa_cnt;
 	dm_info->ofdm_fa_cnt = ofdm_fa_cnt;
+	dm_info->total_fa_cnt = ofdm_fa_cnt;
 	if (cck_enable)
 		dm_info->total_fa_cnt += cck_fa_cnt;
-	dm_info->total_fa_cnt = ofdm_fa_cnt;
 
 	crc32_cnt = rtw_read32(rtwdev, REG_CRC_CCK);
 	dm_info->cck_ok_cnt = FIELD_GET(GENMASK(15, 0), crc32_cnt);
@@ -773,6 +778,15 @@
 	if (switch_status == coex_dm->cur_switch_status)
 		return;
 
+	if (coex_rfe->wlg_at_btg) {
+		ctrl_type = COEX_SWITCH_CTRL_BY_BBSW;
+
+		if (coex_rfe->ant_switch_polarity)
+			pos_type = COEX_SWITCH_TO_WLA;
+		else
+			pos_type = COEX_SWITCH_TO_WLG_BT;
+	}
+
 	coex_dm->cur_switch_status = switch_status;
 
 	if (coex_rfe->ant_switch_diversity &&
@@ -1498,6 +1512,8 @@
 static const struct rtw_rfe_def rtw8821c_rfe_defs[] = {
 	[0] = RTW_DEF_RFE(8821c, 0, 0),
 	[2] = RTW_DEF_RFE_EXT(8821c, 0, 0, 2),
+	[4] = RTW_DEF_RFE_EXT(8821c, 0, 0, 2),
+	[6] = RTW_DEF_RFE(8821c, 0, 0),
 };
 
 static struct rtw_hw_reg rtw8821c_dig[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/rtw8821c.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/rtw8821c.h
@@ -131,7 +131,7 @@
 #define WLAN_TX_FUNC_CFG2		0x30
 #define WLAN_MAC_OPT_NORM_FUNC1		0x98
 #define WLAN_MAC_OPT_LB_FUNC1		0x80
-#define WLAN_MAC_OPT_FUNC2		0x30810041
+#define WLAN_MAC_OPT_FUNC2		0xb0810041
 
 #define WLAN_SIFS_CFG	(WLAN_SIFS_CCK_CONT_TX | \
 			(WLAN_SIFS_OFDM_CONT_TX << BIT_SHIFT_SIFS_OFDM_CTX) | \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/rtw8821c_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/rtw8821c_table.c
@@ -13,7 +13,7 @@
 	0x04F, 0x00000001,
 	0x029, 0x000000F9,
 	0x420, 0x00000080,
-	0x421, 0x0000000F,
+	0x421, 0x0000001F,
 	0x428, 0x0000000A,
 	0x429, 0x00000010,
 	0x430, 0x00000000,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/rtw8822b.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/rtw8822b.c
@@ -204,7 +204,7 @@
 #define WLAN_TX_FUNC_CFG2		0x30
 #define WLAN_MAC_OPT_NORM_FUNC1		0x98
 #define WLAN_MAC_OPT_LB_FUNC1		0x80
-#define WLAN_MAC_OPT_FUNC2		0x30810041
+#define WLAN_MAC_OPT_FUNC2		0xb0810041
 
 #define WLAN_SIFS_CFG	(WLAN_SIFS_CCK_CONT_TX | \
 			(WLAN_SIFS_OFDM_CONT_TX << BIT_SHIFT_SIFS_OFDM_CTX) | \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/rtw8822c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/rtw8822c.c
@@ -1962,7 +1962,7 @@
 #define WLAN_TX_FUNC_CFG2		0x30
 #define WLAN_MAC_OPT_NORM_FUNC1		0x98
 #define WLAN_MAC_OPT_LB_FUNC1		0x80
-#define WLAN_MAC_OPT_FUNC2		0x30810041
+#define WLAN_MAC_OPT_FUNC2		0xb0810041
 #define WLAN_MAC_INT_MIG_CFG		0x33330000
 
 #define WLAN_SIFS_CFG	(WLAN_SIFS_CCK_CONT_TX | \
@@ -2584,12 +2584,14 @@
 	else
 		rxsc = GET_PHY_STAT_P1_HT_RXSC(phy_status);
 
-	if (rxsc >= 9 && rxsc <= 12)
+	if (rxsc == 0)
+		bw = rtwdev->hal.current_band_width;
+	else if (rxsc >= 1 && rxsc <= 8)
+		bw = RTW_CHANNEL_WIDTH_20;
+	else if (rxsc >= 9 && rxsc <= 12)
 		bw = RTW_CHANNEL_WIDTH_40;
-	else if (rxsc >= 13)
-		bw = RTW_CHANNEL_WIDTH_80;
 	else
-		bw = RTW_CHANNEL_WIDTH_20;
+		bw = RTW_CHANNEL_WIDTH_80;
 
 	pkt_stat->rx_power[RF_PATH_A] = GET_PHY_STAT_P1_PWDB_A(phy_status) - 110;
 	pkt_stat->rx_power[RF_PATH_B] = GET_PHY_STAT_P1_PWDB_B(phy_status) - 110;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/tx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/tx.c
@@ -67,6 +67,10 @@
 	SET_TX_DESC_HW_SSN_SEL(txdesc, pkt_info->hw_ssn_sel);
 	SET_TX_DESC_NAVUSEHDR(txdesc, pkt_info->nav_use_hdr);
 	SET_TX_DESC_BT_NULL(txdesc, pkt_info->bt_null);
+	if (pkt_info->tim_offset) {
+		SET_TX_DESC_TIM_EN(txdesc, 1);
+		SET_TX_DESC_TIM_OFFSET(txdesc, pkt_info->tim_offset);
+	}
 }
 EXPORT_SYMBOL(rtw_tx_fill_tx_desc);
 
@@ -422,6 +426,19 @@
 	if (type == RSVD_QOS_NULL)
 		pkt_info->bt_null = true;
 
+	if (type == RSVD_BEACON) {
+		struct rtw_rsvd_page *rsvd_pkt;
+		int hdr_len;
+
+		rsvd_pkt = list_first_entry_or_null(&rtwdev->rsvd_page_list,
+						    struct rtw_rsvd_page,
+						    build_list);
+		if (rsvd_pkt && rsvd_pkt->tim_offset != 0) {
+			hdr_len = sizeof(struct ieee80211_hdr_3addr);
+			pkt_info->tim_offset = rsvd_pkt->tim_offset - hdr_len;
+		}
+	}
+
 	rtw_tx_pkt_info_update_sec(rtwdev, pkt_info, skb);
 
 	/* TODO: need to change hw port and hw ssn sel for multiple vifs */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw88/tx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw88/tx.h
@@ -33,6 +33,10 @@
 	le32p_replace_bits((__le32 *)(txdesc) + 0x05, value, GENMASK(6, 5))
 #define SET_TX_DESC_SW_SEQ(txdesc, value)                                      \
 	le32p_replace_bits((__le32 *)(txdesc) + 0x09, value, GENMASK(23, 12))
+#define SET_TX_DESC_TIM_EN(txdesc, value)                                      \
+	le32p_replace_bits((__le32 *)(txdesc) + 0x09, value, BIT(7))
+#define SET_TX_DESC_TIM_OFFSET(txdesc, value)                                  \
+	le32p_replace_bits((__le32 *)(txdesc) + 0x09, value, GENMASK(6, 0))
 #define SET_TX_DESC_MAX_AGG_NUM(txdesc, value)                                 \
 	le32p_replace_bits((__le32 *)(txdesc) + 0x03, value, GENMASK(21, 17))
 #define SET_TX_DESC_USE_RTS(tx_desc, value)                                    \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/Kconfig
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+menuconfig RTW89
+	tristate "Realtek 802.11ax wireless chips support"
+	depends on MAC80211
+	help
+	  This module adds support for mac80211-based wireless drivers that
+	  enables Realtek IEEE 802.11ax wireless chipsets.
+
+	  If you choose to build a module, it'll be called rtw89.
+
+if RTW89
+
+config RTW89_CORE
+	tristate
+
+config RTW89_PCI
+	tristate
+
+config RTW89_8852AE
+	tristate "Realtek 8852AE PCI wireless network adapter"
+	depends on PCI
+	select RTW89_CORE
+	select RTW89_PCI
+	help
+	  Select this option will enable support for 8852AE chipset
+
+	  802.11ax PCIe wireless network adapter
+
+config RTW89_DEBUG
+	bool
+
+config RTW89_DEBUGMSG
+	bool "Realtek rtw89 debug message support"
+	depends on RTW89_CORE
+	select RTW89_DEBUG
+	help
+	  Enable debug message support
+
+	  If unsure, say Y to simplify debug problems
+
+config RTW89_DEBUGFS
+	bool "Realtek rtw89 debugfs support"
+	depends on RTW89_CORE
+	select RTW89_DEBUG
+	help
+	  Enable debugfs support
+
+	  If unsure, say Y to simplify debug problems
+
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/Makefile
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+
+obj-$(CONFIG_RTW89_CORE) += rtw89_core.o
+rtw89_core-y += core.o \
+		mac80211.o \
+		mac.o \
+		phy.o \
+		fw.o \
+		rtw8852a.o \
+		rtw8852a_table.o \
+		rtw8852a_rfk.o \
+		rtw8852a_rfk_table.o \
+		cam.o \
+		efuse.o \
+		regd.o \
+		sar.o \
+		coex.o \
+		ps.o \
+		ser.o
+
+rtw89_core-$(CONFIG_RTW89_DEBUG) += debug.o
+
+obj-$(CONFIG_RTW89_PCI) += rtw89_pci.o
+rtw89_pci-y := pci.o
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/cam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/cam.c
@@ -0,0 +1,695 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "cam.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+
+static struct sk_buff *
+rtw89_cam_get_sec_key_cmd(struct rtw89_dev *rtwdev,
+			  struct rtw89_sec_cam_entry *sec_cam,
+			  bool ext_key)
+{
+	struct sk_buff *skb;
+	u32 cmd_len = H2C_SEC_CAM_LEN;
+	u32 key32[4];
+	u8 *cmd;
+	int i, j;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(cmd_len);
+	if (!skb)
+		return NULL;
+
+	skb_put_zero(skb, cmd_len);
+
+	for (i = 0; i < 4; i++) {
+		j = i * 4;
+		j += ext_key ? 16 : 0;
+		key32[i] = FIELD_PREP(GENMASK(7, 0), sec_cam->key[j + 0]) |
+			   FIELD_PREP(GENMASK(15, 8), sec_cam->key[j + 1]) |
+			   FIELD_PREP(GENMASK(23, 16), sec_cam->key[j + 2]) |
+			   FIELD_PREP(GENMASK(31, 24), sec_cam->key[j + 3]);
+	}
+
+	cmd = skb->data;
+	RTW89_SET_FWCMD_SEC_IDX(cmd, sec_cam->sec_cam_idx + (ext_key ? 1 : 0));
+	RTW89_SET_FWCMD_SEC_OFFSET(cmd, sec_cam->offset);
+	RTW89_SET_FWCMD_SEC_LEN(cmd, sec_cam->len);
+	RTW89_SET_FWCMD_SEC_TYPE(cmd, sec_cam->type);
+	RTW89_SET_FWCMD_SEC_EXT_KEY(cmd, ext_key);
+	RTW89_SET_FWCMD_SEC_SPP_MODE(cmd, sec_cam->spp_mode);
+	RTW89_SET_FWCMD_SEC_KEY0(cmd, key32[0]);
+	RTW89_SET_FWCMD_SEC_KEY1(cmd, key32[1]);
+	RTW89_SET_FWCMD_SEC_KEY2(cmd, key32[2]);
+	RTW89_SET_FWCMD_SEC_KEY3(cmd, key32[3]);
+
+	return skb;
+}
+
+static int rtw89_cam_send_sec_key_cmd(struct rtw89_dev *rtwdev,
+				      struct rtw89_sec_cam_entry *sec_cam)
+{
+	struct sk_buff *skb, *ext_skb;
+	int ret;
+
+	skb = rtw89_cam_get_sec_key_cmd(rtwdev, sec_cam, false);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to get sec key command\n");
+		return -ENOMEM;
+	}
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb,
+			      FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_MAC_SEC_CAM,
+			      H2C_FUNC_MAC_SEC_UPD, 1, 0,
+			      H2C_SEC_CAM_LEN);
+	ret = rtw89_h2c_tx(rtwdev, skb, false);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to send sec key h2c: %d\n", ret);
+		dev_kfree_skb(skb);
+		return ret;
+	}
+
+	if (!sec_cam->ext_key)
+		return 0;
+
+	ext_skb = rtw89_cam_get_sec_key_cmd(rtwdev, sec_cam, true);
+	if (!ext_skb) {
+		rtw89_err(rtwdev, "failed to get ext sec key command\n");
+		return -ENOMEM;
+	}
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, ext_skb,
+			      FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_MAC_SEC_CAM,
+			      H2C_FUNC_MAC_SEC_UPD,
+			      1, 0, H2C_SEC_CAM_LEN);
+	ret = rtw89_h2c_tx(rtwdev, ext_skb, false);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to send ext sec key h2c: %d\n", ret);
+		dev_kfree_skb(ext_skb);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rtw89_cam_get_avail_sec_cam(struct rtw89_dev *rtwdev,
+				       u8 *sec_cam_idx, bool ext_key)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_cam_info *cam_info = &rtwdev->cam_info;
+	u8 sec_cam_num = chip->scam_num;
+	u8 idx = 0;
+
+	if (!ext_key) {
+		idx = find_first_zero_bit(cam_info->sec_cam_map, sec_cam_num);
+		if (idx >= sec_cam_num)
+			return -EBUSY;
+
+		set_bit(idx, cam_info->sec_cam_map);
+		*sec_cam_idx = idx;
+
+		return 0;
+	}
+
+again:
+	idx = find_next_zero_bit(cam_info->sec_cam_map, sec_cam_num, idx);
+	if (idx >= sec_cam_num - 1)
+		return -EBUSY;
+	/* ext keys need two cam entries for 256-bit key */
+	if (test_bit(idx + 1, cam_info->sec_cam_map)) {
+		idx++;
+		goto again;
+	}
+
+	set_bit(idx, cam_info->sec_cam_map);
+	set_bit(idx + 1, cam_info->sec_cam_map);
+	*sec_cam_idx = idx;
+
+	return 0;
+}
+
+static int rtw89_cam_get_addr_cam_key_idx(struct rtw89_addr_cam_entry *addr_cam,
+					  struct rtw89_sec_cam_entry *sec_cam,
+					  struct ieee80211_key_conf *key,
+					  u8 *key_idx)
+{
+	u8 idx;
+
+	/* RTW89_ADDR_CAM_SEC_NONE	: not enabled
+	 * RTW89_ADDR_CAM_SEC_ALL_UNI	: 0 - 6 unicast
+	 * RTW89_ADDR_CAM_SEC_NORMAL	: 0 - 1 unicast, 2 - 4 group, 5 - 6 BIP
+	 * RTW89_ADDR_CAM_SEC_4GROUP	: 0 - 1 unicast, 2 - 5 group, 6 BIP
+	 */
+	switch (addr_cam->sec_ent_mode) {
+	case RTW89_ADDR_CAM_SEC_NONE:
+		return -EINVAL;
+	case RTW89_ADDR_CAM_SEC_ALL_UNI:
+		if (!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
+			return -EINVAL;
+		idx = find_first_zero_bit(addr_cam->sec_cam_map,
+					  RTW89_SEC_CAM_IN_ADDR_CAM);
+		if (idx >= RTW89_SEC_CAM_IN_ADDR_CAM)
+			return -EBUSY;
+		*key_idx = idx;
+		break;
+	case RTW89_ADDR_CAM_SEC_NORMAL:
+		if (sec_cam->type == RTW89_SEC_KEY_TYPE_BIP_CCMP128) {
+			idx = find_next_zero_bit(addr_cam->sec_cam_map,
+						 RTW89_SEC_CAM_IN_ADDR_CAM, 5);
+			if (idx > 6)
+				return -EBUSY;
+			*key_idx = idx;
+			break;
+		}
+
+		if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) {
+			idx = find_next_zero_bit(addr_cam->sec_cam_map,
+						 RTW89_SEC_CAM_IN_ADDR_CAM, 0);
+			if (idx > 1)
+				return -EBUSY;
+			*key_idx = idx;
+			break;
+		}
+
+		/* Group keys */
+		idx = find_next_zero_bit(addr_cam->sec_cam_map,
+					 RTW89_SEC_CAM_IN_ADDR_CAM, 2);
+		if (idx > 4)
+			return -EBUSY;
+		*key_idx = idx;
+		break;
+	case RTW89_ADDR_CAM_SEC_4GROUP:
+		if (sec_cam->type == RTW89_SEC_KEY_TYPE_BIP_CCMP128) {
+			if (test_bit(6, addr_cam->sec_cam_map))
+				return -EINVAL;
+			*key_idx = 6;
+			break;
+		}
+
+		if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) {
+			idx = find_next_zero_bit(addr_cam->sec_cam_map,
+						 RTW89_SEC_CAM_IN_ADDR_CAM, 0);
+			if (idx > 1)
+				return -EBUSY;
+			*key_idx = idx;
+			break;
+		}
+
+		/* Group keys */
+		idx = find_next_zero_bit(addr_cam->sec_cam_map,
+					 RTW89_SEC_CAM_IN_ADDR_CAM, 2);
+		if (idx > 5)
+			return -EBUSY;
+		*key_idx = idx;
+		break;
+	}
+
+	return 0;
+}
+
+static int rtw89_cam_attach_sec_cam(struct rtw89_dev *rtwdev,
+				    struct ieee80211_vif *vif,
+				    struct ieee80211_sta *sta,
+				    struct ieee80211_key_conf *key,
+				    struct rtw89_sec_cam_entry *sec_cam)
+{
+	struct rtw89_vif *rtwvif;
+	struct rtw89_addr_cam_entry *addr_cam;
+	u8 key_idx = 0;
+	int ret;
+
+	if (!vif) {
+		rtw89_err(rtwdev, "No iface for adding sec cam\n");
+		return -EINVAL;
+	}
+
+	rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	addr_cam = &rtwvif->addr_cam;
+	ret = rtw89_cam_get_addr_cam_key_idx(addr_cam, sec_cam, key, &key_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get addr cam key idx %d, %d\n",
+			  addr_cam->sec_ent_mode, sec_cam->type);
+		return ret;
+	}
+
+	key->hw_key_idx = key_idx;
+	addr_cam->sec_ent_keyid[key_idx] = key->keyidx;
+	addr_cam->sec_ent[key_idx] = sec_cam->sec_cam_idx;
+	addr_cam->sec_entries[key_idx] = sec_cam;
+	set_bit(key_idx, addr_cam->sec_cam_map);
+	ret = rtw89_fw_h2c_cam(rtwdev, rtwvif);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to update addr cam sec entry: %d\n",
+			  ret);
+		clear_bit(key_idx, addr_cam->sec_cam_map);
+		addr_cam->sec_entries[key_idx] = NULL;
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rtw89_cam_sec_key_install(struct rtw89_dev *rtwdev,
+				     struct ieee80211_vif *vif,
+				     struct ieee80211_sta *sta,
+				     struct ieee80211_key_conf *key,
+				     u8 hw_key_type, bool ext_key)
+{
+	struct rtw89_sec_cam_entry *sec_cam = NULL;
+	struct rtw89_cam_info *cam_info = &rtwdev->cam_info;
+	u8 sec_cam_idx;
+	int ret;
+
+	/* maximum key length 256-bit */
+	if (key->keylen > 32) {
+		rtw89_err(rtwdev, "invalid sec key length %d\n", key->keylen);
+		return -EINVAL;
+	}
+
+	ret = rtw89_cam_get_avail_sec_cam(rtwdev, &sec_cam_idx, ext_key);
+	if (ret) {
+		rtw89_warn(rtwdev, "no available sec cam: %d ext: %d\n",
+			   ret, ext_key);
+		return ret;
+	}
+
+	sec_cam = kzalloc(sizeof(*sec_cam), GFP_KERNEL);
+	if (!sec_cam) {
+		ret = -ENOMEM;
+		goto err_release_cam;
+	}
+
+	sec_cam->sec_cam_idx = sec_cam_idx;
+	sec_cam->type = hw_key_type;
+	sec_cam->len = RTW89_SEC_CAM_LEN;
+	sec_cam->ext_key = ext_key;
+	memcpy(sec_cam->key, key->key, key->keylen);
+	ret = rtw89_cam_send_sec_key_cmd(rtwdev, sec_cam);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to send sec key cmd: %d\n", ret);
+		goto err_release_cam;
+	}
+
+	/* associate with addr cam */
+	ret = rtw89_cam_attach_sec_cam(rtwdev, vif, sta, key, sec_cam);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to attach sec cam: %d\n", ret);
+		goto err_release_cam;
+	}
+
+	return 0;
+
+err_release_cam:
+	kfree(sec_cam);
+	clear_bit(sec_cam_idx, cam_info->sec_cam_map);
+	if (ext_key)
+		clear_bit(sec_cam_idx + 1, cam_info->sec_cam_map);
+
+	return ret;
+}
+
+int rtw89_cam_sec_key_add(struct rtw89_dev *rtwdev,
+			  struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta,
+			  struct ieee80211_key_conf *key)
+{
+	u8 hw_key_type;
+	bool ext_key = false;
+	int ret;
+
+	switch (key->cipher) {
+	case WLAN_CIPHER_SUITE_WEP40:
+		hw_key_type = RTW89_SEC_KEY_TYPE_WEP40;
+		break;
+	case WLAN_CIPHER_SUITE_WEP104:
+		hw_key_type = RTW89_SEC_KEY_TYPE_WEP104;
+		break;
+	case WLAN_CIPHER_SUITE_CCMP:
+		hw_key_type = RTW89_SEC_KEY_TYPE_CCMP128;
+		key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX;
+		break;
+	case WLAN_CIPHER_SUITE_CCMP_256:
+		hw_key_type = RTW89_SEC_KEY_TYPE_CCMP256;
+		key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX;
+		ext_key = true;
+		break;
+	case WLAN_CIPHER_SUITE_GCMP:
+		hw_key_type = RTW89_SEC_KEY_TYPE_GCMP128;
+		key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX;
+		break;
+	case WLAN_CIPHER_SUITE_GCMP_256:
+		hw_key_type = RTW89_SEC_KEY_TYPE_GCMP256;
+		key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX;
+		ext_key = true;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+
+	ret = rtw89_cam_sec_key_install(rtwdev, vif, sta, key, hw_key_type,
+					ext_key);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to install key type %d ext %d: %d\n",
+			  hw_key_type, ext_key, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+int rtw89_cam_sec_key_del(struct rtw89_dev *rtwdev,
+			  struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta,
+			  struct ieee80211_key_conf *key,
+			  bool inform_fw)
+{
+	struct rtw89_cam_info *cam_info = &rtwdev->cam_info;
+	struct rtw89_vif *rtwvif;
+	struct rtw89_addr_cam_entry *addr_cam;
+	struct rtw89_sec_cam_entry *sec_cam;
+	u8 key_idx = key->hw_key_idx;
+	u8 sec_cam_idx;
+	int ret = 0;
+
+	if (!vif) {
+		rtw89_err(rtwdev, "No iface for deleting sec cam\n");
+		return -EINVAL;
+	}
+
+	rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	addr_cam = &rtwvif->addr_cam;
+	sec_cam = addr_cam->sec_entries[key_idx];
+	if (!sec_cam)
+		return -EINVAL;
+
+	/* detach sec cam from addr cam */
+	clear_bit(key_idx, addr_cam->sec_cam_map);
+	addr_cam->sec_entries[key_idx] = NULL;
+	if (inform_fw) {
+		ret = rtw89_fw_h2c_cam(rtwdev, rtwvif);
+		if (ret)
+			rtw89_err(rtwdev, "failed to update cam del key: %d\n", ret);
+	}
+
+	/* clear valid bit in addr cam will disable sec cam,
+	 * so we don't need to send H2C command again
+	 */
+	sec_cam_idx = sec_cam->sec_cam_idx;
+	clear_bit(sec_cam_idx, cam_info->sec_cam_map);
+	if (sec_cam->ext_key)
+		clear_bit(sec_cam_idx + 1, cam_info->sec_cam_map);
+
+	kfree(sec_cam);
+
+	return ret;
+}
+
+static void rtw89_cam_reset_key_iter(struct ieee80211_hw *hw,
+				     struct ieee80211_vif *vif,
+				     struct ieee80211_sta *sta,
+				     struct ieee80211_key_conf *key,
+				     void *data)
+{
+	struct rtw89_dev *rtwdev = (struct rtw89_dev *)data;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	rtw89_cam_sec_key_del(rtwdev, vif, sta, key, false);
+	rtw89_cam_deinit(rtwdev, rtwvif);
+}
+
+void rtw89_cam_deinit(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	struct rtw89_cam_info *cam_info = &rtwdev->cam_info;
+	struct rtw89_addr_cam_entry *addr_cam = &rtwvif->addr_cam;
+	struct rtw89_bssid_cam_entry *bssid_cam = &rtwvif->bssid_cam;
+
+	addr_cam->valid = false;
+	bssid_cam->valid = false;
+	clear_bit(addr_cam->addr_cam_idx, cam_info->addr_cam_map);
+	clear_bit(bssid_cam->bssid_cam_idx, cam_info->bssid_cam_map);
+}
+
+void rtw89_cam_reset_keys(struct rtw89_dev *rtwdev)
+{
+	rcu_read_lock();
+	ieee80211_iter_keys_rcu(rtwdev->hw, NULL, rtw89_cam_reset_key_iter, rtwdev);
+	rcu_read_unlock();
+}
+
+static int rtw89_cam_get_avail_addr_cam(struct rtw89_dev *rtwdev,
+					u8 *addr_cam_idx)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_cam_info *cam_info = &rtwdev->cam_info;
+	u8 addr_cam_num = chip->acam_num;
+	u8 idx;
+
+	idx = find_first_zero_bit(cam_info->addr_cam_map, addr_cam_num);
+	if (idx >= addr_cam_num)
+		return -EBUSY;
+
+	set_bit(idx, cam_info->addr_cam_map);
+	*addr_cam_idx = idx;
+
+	return 0;
+}
+
+static int rtw89_cam_init_addr_cam(struct rtw89_dev *rtwdev,
+				   struct rtw89_vif *rtwvif)
+{
+	struct rtw89_addr_cam_entry *addr_cam = &rtwvif->addr_cam;
+	u8 addr_cam_idx;
+	int i;
+	int ret;
+
+	ret = rtw89_cam_get_avail_addr_cam(rtwdev, &addr_cam_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get available addr cam\n");
+		return ret;
+	}
+
+	addr_cam->addr_cam_idx = addr_cam_idx;
+	addr_cam->len = ADDR_CAM_ENT_SIZE;
+	addr_cam->offset = 0;
+	addr_cam->valid = true;
+	addr_cam->addr_mask = 0;
+	addr_cam->mask_sel = RTW89_NO_MSK;
+	bitmap_zero(addr_cam->sec_cam_map, RTW89_SEC_CAM_IN_ADDR_CAM);
+	ether_addr_copy(addr_cam->sma, rtwvif->mac_addr);
+
+	for (i = 0; i < RTW89_SEC_CAM_IN_ADDR_CAM; i++) {
+		addr_cam->sec_ent_keyid[i] = 0;
+		addr_cam->sec_ent[i] = 0;
+	}
+
+	return 0;
+}
+
+static int rtw89_cam_get_avail_bssid_cam(struct rtw89_dev *rtwdev,
+					 u8 *bssid_cam_idx)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_cam_info *cam_info = &rtwdev->cam_info;
+	u8 bssid_cam_num = chip->bcam_num;
+	u8 idx;
+
+	idx = find_first_zero_bit(cam_info->bssid_cam_map, bssid_cam_num);
+	if (idx >= bssid_cam_num)
+		return -EBUSY;
+
+	set_bit(idx, cam_info->bssid_cam_map);
+	*bssid_cam_idx = idx;
+
+	return 0;
+}
+
+static int rtw89_cam_init_bssid_cam(struct rtw89_dev *rtwdev,
+				    struct rtw89_vif *rtwvif)
+{
+	struct rtw89_bssid_cam_entry *bssid_cam = &rtwvif->bssid_cam;
+	u8 bssid_cam_idx;
+	int ret;
+
+	ret = rtw89_cam_get_avail_bssid_cam(rtwdev, &bssid_cam_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get available bssid cam\n");
+		return ret;
+	}
+
+	bssid_cam->bssid_cam_idx = bssid_cam_idx;
+	bssid_cam->phy_idx = rtwvif->phy_idx;
+	bssid_cam->len = BSSID_CAM_ENT_SIZE;
+	bssid_cam->offset = 0;
+	bssid_cam->valid = true;
+	ether_addr_copy(bssid_cam->bssid, rtwvif->bssid);
+
+	return 0;
+}
+
+void rtw89_cam_bssid_changed(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	struct rtw89_addr_cam_entry *addr_cam = &rtwvif->addr_cam;
+	struct rtw89_bssid_cam_entry *bssid_cam = &rtwvif->bssid_cam;
+
+	if (vif->type == NL80211_IFTYPE_STATION)
+		ether_addr_copy(addr_cam->tma, rtwvif->bssid);
+	ether_addr_copy(bssid_cam->bssid, rtwvif->bssid);
+}
+
+int rtw89_cam_init(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	struct rtw89_addr_cam_entry *addr_cam = &rtwvif->addr_cam;
+	struct rtw89_bssid_cam_entry *bssid_cam = &rtwvif->bssid_cam;
+	int ret;
+
+	ret = rtw89_cam_init_addr_cam(rtwdev, rtwvif);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to init addr cam\n");
+		return ret;
+	}
+
+	ret = rtw89_cam_init_bssid_cam(rtwdev, rtwvif);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to init bssid cam\n");
+		return ret;
+	}
+
+	/* associate addr cam with bssid cam */
+	addr_cam->bssid_cam_idx = bssid_cam->bssid_cam_idx;
+
+	return 0;
+}
+
+int rtw89_cam_fill_bssid_cam_info(struct rtw89_dev *rtwdev,
+				  struct rtw89_vif *rtwvif, u8 *cmd)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	struct rtw89_bssid_cam_entry *bssid_cam = &rtwvif->bssid_cam;
+	u8 bss_color = vif->bss_conf.he_bss_color.color;
+
+	FWCMD_SET_ADDR_BSSID_IDX(cmd, bssid_cam->bssid_cam_idx);
+	FWCMD_SET_ADDR_BSSID_OFFSET(cmd, bssid_cam->offset);
+	FWCMD_SET_ADDR_BSSID_LEN(cmd, bssid_cam->len);
+	FWCMD_SET_ADDR_BSSID_VALID(cmd, bssid_cam->valid);
+	FWCMD_SET_ADDR_BSSID_BB_SEL(cmd, bssid_cam->phy_idx);
+	FWCMD_SET_ADDR_BSSID_BSS_COLOR(cmd, bss_color);
+
+	FWCMD_SET_ADDR_BSSID_BSSID0(cmd, bssid_cam->bssid[0]);
+	FWCMD_SET_ADDR_BSSID_BSSID1(cmd, bssid_cam->bssid[1]);
+	FWCMD_SET_ADDR_BSSID_BSSID2(cmd, bssid_cam->bssid[2]);
+	FWCMD_SET_ADDR_BSSID_BSSID3(cmd, bssid_cam->bssid[3]);
+	FWCMD_SET_ADDR_BSSID_BSSID4(cmd, bssid_cam->bssid[4]);
+	FWCMD_SET_ADDR_BSSID_BSSID5(cmd, bssid_cam->bssid[5]);
+
+	return 0;
+}
+
+static u8 rtw89_cam_addr_hash(u8 start, u8 *addr)
+{
+	u8 hash = 0;
+	u8 i;
+
+	for (i = start; i < ETH_ALEN; i++)
+		hash ^= addr[i];
+
+	return hash;
+}
+
+void rtw89_cam_fill_addr_cam_info(struct rtw89_dev *rtwdev,
+				  struct rtw89_vif *rtwvif,
+				  u8 *cmd)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	struct ieee80211_sta *sta;
+	struct rtw89_sta *rtwsta;
+	struct rtw89_addr_cam_entry *addr_cam = &rtwvif->addr_cam;
+	u8 sma_hash, tma_hash, addr_msk_start;
+	u8 sma_start = 0;
+	u8 tma_start = 0;
+
+	if (addr_cam->addr_mask != 0) {
+		addr_msk_start = __ffs(addr_cam->addr_mask);
+		if (addr_cam->mask_sel == RTW89_SMA)
+			sma_start = addr_msk_start;
+		else if (addr_cam->mask_sel == RTW89_TMA)
+			tma_start = addr_msk_start;
+	}
+	sma_hash = rtw89_cam_addr_hash(sma_start, rtwvif->mac_addr);
+	tma_hash = rtw89_cam_addr_hash(tma_start, addr_cam->tma);
+
+	FWCMD_SET_ADDR_IDX(cmd, addr_cam->addr_cam_idx);
+	FWCMD_SET_ADDR_OFFSET(cmd, addr_cam->offset);
+	FWCMD_SET_ADDR_LEN(cmd, addr_cam->len);
+
+	FWCMD_SET_ADDR_VALID(cmd, addr_cam->valid);
+	FWCMD_SET_ADDR_NET_TYPE(cmd, rtwvif->net_type);
+	FWCMD_SET_ADDR_BCN_HIT_COND(cmd, rtwvif->bcn_hit_cond);
+	FWCMD_SET_ADDR_HIT_RULE(cmd, rtwvif->hit_rule);
+	FWCMD_SET_ADDR_BB_SEL(cmd, rtwvif->phy_idx);
+	FWCMD_SET_ADDR_ADDR_MASK(cmd, addr_cam->addr_mask);
+	FWCMD_SET_ADDR_MASK_SEL(cmd, addr_cam->mask_sel);
+	FWCMD_SET_ADDR_SMA_HASH(cmd, sma_hash);
+	FWCMD_SET_ADDR_TMA_HASH(cmd, tma_hash);
+
+	FWCMD_SET_ADDR_BSSID_CAM_IDX(cmd, addr_cam->bssid_cam_idx);
+
+	FWCMD_SET_ADDR_SMA0(cmd, rtwvif->mac_addr[0]);
+	FWCMD_SET_ADDR_SMA1(cmd, rtwvif->mac_addr[1]);
+	FWCMD_SET_ADDR_SMA2(cmd, rtwvif->mac_addr[2]);
+	FWCMD_SET_ADDR_SMA3(cmd, rtwvif->mac_addr[3]);
+	FWCMD_SET_ADDR_SMA4(cmd, rtwvif->mac_addr[4]);
+	FWCMD_SET_ADDR_SMA5(cmd, rtwvif->mac_addr[5]);
+
+	FWCMD_SET_ADDR_TMA0(cmd, addr_cam->tma[0]);
+	FWCMD_SET_ADDR_TMA1(cmd, addr_cam->tma[1]);
+	FWCMD_SET_ADDR_TMA2(cmd, addr_cam->tma[2]);
+	FWCMD_SET_ADDR_TMA3(cmd, addr_cam->tma[3]);
+	FWCMD_SET_ADDR_TMA4(cmd, addr_cam->tma[4]);
+	FWCMD_SET_ADDR_TMA5(cmd, addr_cam->tma[5]);
+
+	FWCMD_SET_ADDR_PORT_INT(cmd, rtwvif->port);
+	FWCMD_SET_ADDR_TSF_SYNC(cmd, rtwvif->port);
+	FWCMD_SET_ADDR_TF_TRS(cmd, rtwvif->trigger);
+	FWCMD_SET_ADDR_LSIG_TXOP(cmd, rtwvif->lsig_txop);
+	FWCMD_SET_ADDR_TGT_IND(cmd, rtwvif->tgt_ind);
+	FWCMD_SET_ADDR_FRM_TGT_IND(cmd, rtwvif->frm_tgt_ind);
+
+	if (vif->type == NL80211_IFTYPE_STATION) {
+		sta = rtwvif->mgd.ap;
+		if (sta) {
+			rtwsta = (struct rtw89_sta *)sta->drv_priv;
+			FWCMD_SET_ADDR_MACID(cmd, rtwsta->mac_id);
+			FWCMD_SET_ADDR_AID12(cmd, vif->bss_conf.aid & 0xfff);
+		}
+	}
+	FWCMD_SET_ADDR_WOL_PATTERN(cmd, rtwvif->wowlan_pattern);
+	FWCMD_SET_ADDR_WOL_UC(cmd, rtwvif->wowlan_uc);
+	FWCMD_SET_ADDR_WOL_MAGIC(cmd, rtwvif->wowlan_magic);
+	FWCMD_SET_ADDR_WAPI(cmd, addr_cam->wapi);
+	FWCMD_SET_ADDR_SEC_ENT_MODE(cmd, addr_cam->sec_ent_mode);
+	FWCMD_SET_ADDR_SEC_ENT0_KEYID(cmd, addr_cam->sec_ent_keyid[0]);
+	FWCMD_SET_ADDR_SEC_ENT1_KEYID(cmd, addr_cam->sec_ent_keyid[1]);
+	FWCMD_SET_ADDR_SEC_ENT2_KEYID(cmd, addr_cam->sec_ent_keyid[2]);
+	FWCMD_SET_ADDR_SEC_ENT3_KEYID(cmd, addr_cam->sec_ent_keyid[3]);
+	FWCMD_SET_ADDR_SEC_ENT4_KEYID(cmd, addr_cam->sec_ent_keyid[4]);
+	FWCMD_SET_ADDR_SEC_ENT5_KEYID(cmd, addr_cam->sec_ent_keyid[5]);
+	FWCMD_SET_ADDR_SEC_ENT6_KEYID(cmd, addr_cam->sec_ent_keyid[6]);
+
+	FWCMD_SET_ADDR_SEC_ENT_VALID(cmd, addr_cam->sec_cam_map[0] & 0xff);
+	FWCMD_SET_ADDR_SEC_ENT0(cmd, addr_cam->sec_ent[0]);
+	FWCMD_SET_ADDR_SEC_ENT1(cmd, addr_cam->sec_ent[1]);
+	FWCMD_SET_ADDR_SEC_ENT2(cmd, addr_cam->sec_ent[2]);
+	FWCMD_SET_ADDR_SEC_ENT3(cmd, addr_cam->sec_ent[3]);
+	FWCMD_SET_ADDR_SEC_ENT4(cmd, addr_cam->sec_ent[4]);
+	FWCMD_SET_ADDR_SEC_ENT5(cmd, addr_cam->sec_ent[5]);
+	FWCMD_SET_ADDR_SEC_ENT6(cmd, addr_cam->sec_ent[6]);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/cam.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/cam.h
@@ -0,0 +1,165 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_CAM_H__
+#define __RTW89_CAM_H__
+
+#include "core.h"
+
+#define RTW89_SEC_CAM_LEN	20
+
+#define FWCMD_SET_ADDR_IDX(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 1, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_OFFSET(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 1, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_LEN(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 1, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_VALID(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, BIT(0))
+#define FWCMD_SET_ADDR_NET_TYPE(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(2, 1))
+#define FWCMD_SET_ADDR_BCN_HIT_COND(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(4, 3))
+#define FWCMD_SET_ADDR_HIT_RULE(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(6, 5))
+#define FWCMD_SET_ADDR_BB_SEL(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, BIT(7))
+#define FWCMD_SET_ADDR_ADDR_MASK(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(13, 8))
+#define FWCMD_SET_ADDR_MASK_SEL(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(15, 14))
+#define FWCMD_SET_ADDR_SMA_HASH(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_TMA_HASH(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 2, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_BSSID_CAM_IDX(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 3, value, GENMASK(5, 0))
+#define FWCMD_SET_ADDR_SMA0(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 4, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_SMA1(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 4, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_SMA2(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 4, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_SMA3(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 4, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_SMA4(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 5, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_SMA5(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 5, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_TMA0(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 5, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_TMA1(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 5, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_TMA2(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 6, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_TMA3(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 6, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_TMA4(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 6, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_TMA5(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 6, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_MACID(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_PORT_INT(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, GENMASK(10, 8))
+#define FWCMD_SET_ADDR_TSF_SYNC(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, GENMASK(13, 11))
+#define FWCMD_SET_ADDR_TF_TRS(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, BIT(14))
+#define FWCMD_SET_ADDR_LSIG_TXOP(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, BIT(15))
+#define FWCMD_SET_ADDR_TGT_IND(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, GENMASK(26, 24))
+#define FWCMD_SET_ADDR_FRM_TGT_IND(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 8, value, GENMASK(29, 27))
+#define FWCMD_SET_ADDR_AID12(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(11, 0))
+#define FWCMD_SET_ADDR_AID12_0(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_AID12_1(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(11, 8))
+#define FWCMD_SET_ADDR_WOL_PATTERN(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, BIT(12))
+#define FWCMD_SET_ADDR_WOL_UC(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, BIT(13))
+#define FWCMD_SET_ADDR_WOL_MAGIC(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, BIT(14))
+#define FWCMD_SET_ADDR_WAPI(cmd, value)					\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, BIT(15))
+#define FWCMD_SET_ADDR_SEC_ENT_MODE(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(17, 16))
+#define FWCMD_SET_ADDR_SEC_ENT0_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(19, 18))
+#define FWCMD_SET_ADDR_SEC_ENT1_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(21, 20))
+#define FWCMD_SET_ADDR_SEC_ENT2_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(23, 22))
+#define FWCMD_SET_ADDR_SEC_ENT3_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(25, 24))
+#define FWCMD_SET_ADDR_SEC_ENT4_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(27, 26))
+#define FWCMD_SET_ADDR_SEC_ENT5_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(29, 28))
+#define FWCMD_SET_ADDR_SEC_ENT6_KEYID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 9, value, GENMASK(31, 30))
+#define FWCMD_SET_ADDR_SEC_ENT_VALID(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 10, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_SEC_ENT0(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 10, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_SEC_ENT1(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 10, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_SEC_ENT2(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 10, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_SEC_ENT3(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 11, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_SEC_ENT4(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 11, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_SEC_ENT5(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 11, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_SEC_ENT6(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 11, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_BSSID_IDX(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 12, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_BSSID_OFFSET(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 12, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_BSSID_LEN(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 12, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_BSSID_VALID(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 13, value, BIT(0))
+#define FWCMD_SET_ADDR_BSSID_BB_SEL(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 13, value, BIT(1))
+#define FWCMD_SET_ADDR_BSSID_BSS_COLOR(cmd, value)			\
+	le32p_replace_bits((__le32 *)(cmd) + 13, value, GENMASK(13, 8))
+#define FWCMD_SET_ADDR_BSSID_BSSID0(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 13, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_BSSID_BSSID1(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 13, value, GENMASK(31, 24))
+#define FWCMD_SET_ADDR_BSSID_BSSID2(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 14, value, GENMASK(7, 0))
+#define FWCMD_SET_ADDR_BSSID_BSSID3(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 14, value, GENMASK(15, 8))
+#define FWCMD_SET_ADDR_BSSID_BSSID4(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 14, value, GENMASK(23, 16))
+#define FWCMD_SET_ADDR_BSSID_BSSID5(cmd, value)				\
+	le32p_replace_bits((__le32 *)(cmd) + 14, value, GENMASK(31, 24))
+
+int rtw89_cam_init(struct rtw89_dev *rtwdev, struct rtw89_vif *vif);
+void rtw89_cam_deinit(struct rtw89_dev *rtwdev, struct rtw89_vif *vif);
+void rtw89_cam_fill_addr_cam_info(struct rtw89_dev *rtwdev,
+				  struct rtw89_vif *vif, u8 *cmd);
+int rtw89_cam_fill_bssid_cam_info(struct rtw89_dev *rtwdev,
+				  struct rtw89_vif *vif, u8 *cmd);
+int rtw89_cam_sec_key_add(struct rtw89_dev *rtwdev,
+			  struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta,
+			  struct ieee80211_key_conf *key);
+int rtw89_cam_sec_key_del(struct rtw89_dev *rtwdev,
+			  struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta,
+			  struct ieee80211_key_conf *key,
+			  bool inform_fw);
+void rtw89_cam_bssid_changed(struct rtw89_dev *rtwdev,
+			     struct rtw89_vif *rtwvif);
+void rtw89_cam_reset_keys(struct rtw89_dev *rtwdev);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/coex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/coex.c
@@ -0,0 +1,5716 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "coex.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+#include "ps.h"
+#include "reg.h"
+
+#define FCXDEF_STEP 50 /* MUST <= FCXMAX_STEP and match with wl fw*/
+
+enum btc_fbtc_tdma_template {
+	CXTD_OFF = 0x0,
+	CXTD_OFF_B2,
+	CXTD_OFF_EXT,
+	CXTD_FIX,
+	CXTD_PFIX,
+	CXTD_AUTO,
+	CXTD_PAUTO,
+	CXTD_AUTO2,
+	CXTD_PAUTO2,
+	CXTD_MAX,
+};
+
+enum btc_fbtc_tdma_type {
+	CXTDMA_OFF = 0x0,
+	CXTDMA_FIX = 0x1,
+	CXTDMA_AUTO = 0x2,
+	CXTDMA_AUTO2 = 0x3,
+	CXTDMA_MAX
+};
+
+enum btc_fbtc_tdma_rx_flow_ctrl {
+	CXFLC_OFF = 0x0,
+	CXFLC_NULLP = 0x1,
+	CXFLC_QOSNULL = 0x2,
+	CXFLC_CTS = 0x3,
+	CXFLC_MAX
+};
+
+enum btc_fbtc_tdma_wlan_tx_pause {
+	CXTPS_OFF = 0x0,  /* no wl tx pause*/
+	CXTPS_ON = 0x1,
+	CXTPS_MAX
+};
+
+enum btc_mlme_state {
+	MLME_NO_LINK,
+	MLME_LINKING,
+	MLME_LINKED,
+};
+
+#define FCXONESLOT_VER 1
+struct btc_fbtc_1slot {
+	u8 fver;
+	u8 sid; /* slot id */
+	struct rtw89_btc_fbtc_slot slot;
+} __packed;
+
+static const struct rtw89_btc_fbtc_tdma t_def[] = {
+	[CXTD_OFF]	= { CXTDMA_OFF,    CXFLC_OFF, CXTPS_OFF, 0, 0, 0, 0, 0},
+	[CXTD_OFF_B2]	= { CXTDMA_OFF,    CXFLC_OFF, CXTPS_OFF, 0, 0, 1, 0, 0},
+	[CXTD_OFF_EXT]	= { CXTDMA_OFF,    CXFLC_OFF, CXTPS_OFF, 0, 0, 3, 0, 0},
+	[CXTD_FIX]	= { CXTDMA_FIX,    CXFLC_OFF, CXTPS_OFF, 0, 0, 0, 0, 0},
+	[CXTD_PFIX]	= { CXTDMA_FIX,  CXFLC_NULLP,  CXTPS_ON, 0, 5, 0, 0, 0},
+	[CXTD_AUTO]	= { CXTDMA_AUTO,   CXFLC_OFF, CXTPS_OFF, 0, 0, 0, 0, 0},
+	[CXTD_PAUTO]	= { CXTDMA_AUTO, CXFLC_NULLP,  CXTPS_ON, 0, 5, 0, 0, 0},
+	[CXTD_AUTO2]	= {CXTDMA_AUTO2,   CXFLC_OFF, CXTPS_OFF, 0, 0, 0, 0, 0},
+	[CXTD_PAUTO2]	= {CXTDMA_AUTO2, CXFLC_NULLP,  CXTPS_ON, 0, 5, 0, 0, 0}
+};
+
+#define __DEF_FBTC_SLOT(__dur, __cxtbl, __cxtype) \
+	{ .dur = cpu_to_le16(__dur), .cxtbl = cpu_to_le32(__cxtbl), \
+	  .cxtype = cpu_to_le16(__cxtype),}
+
+static const struct rtw89_btc_fbtc_slot s_def[] = {
+	[CXST_OFF]	= __DEF_FBTC_SLOT(100, 0x55555555, SLOT_MIX),
+	[CXST_B2W]	= __DEF_FBTC_SLOT(5,   0x5a5a5a5a, SLOT_ISO),
+	[CXST_W1]	= __DEF_FBTC_SLOT(70,  0x5a5a5a5a, SLOT_ISO),
+	[CXST_W2]	= __DEF_FBTC_SLOT(70,  0x5a5a5aaa, SLOT_ISO),
+	[CXST_W2B]	= __DEF_FBTC_SLOT(15,  0x5a5a5a5a, SLOT_ISO),
+	[CXST_B1]	= __DEF_FBTC_SLOT(100, 0x55555555, SLOT_MIX),
+	[CXST_B2]	= __DEF_FBTC_SLOT(7,   0x6a5a5a5a, SLOT_MIX),
+	[CXST_B3]	= __DEF_FBTC_SLOT(5,   0x55555555, SLOT_MIX),
+	[CXST_B4]	= __DEF_FBTC_SLOT(50,  0x55555555, SLOT_MIX),
+	[CXST_LK]	= __DEF_FBTC_SLOT(20,  0x5a5a5a5a, SLOT_ISO),
+	[CXST_BLK]	= __DEF_FBTC_SLOT(250, 0x55555555, SLOT_MIX),
+	[CXST_E2G]	= __DEF_FBTC_SLOT(20,  0x6a5a5a5a, SLOT_MIX),
+	[CXST_E5G]	= __DEF_FBTC_SLOT(20,  0xffffffff, SLOT_MIX),
+	[CXST_EBT]	= __DEF_FBTC_SLOT(20,  0x55555555, SLOT_MIX),
+	[CXST_ENULL]	= __DEF_FBTC_SLOT(7,   0xaaaaaaaa, SLOT_ISO),
+	[CXST_WLK]	= __DEF_FBTC_SLOT(250, 0x6a5a6a5a, SLOT_MIX),
+	[CXST_W1FDD]	= __DEF_FBTC_SLOT(35,  0xfafafafa, SLOT_ISO),
+	[CXST_B1FDD]	= __DEF_FBTC_SLOT(100, 0xffffffff, SLOT_MIX),
+};
+
+static const u32 cxtbl[] = {
+	0xffffffff, /* 0 */
+	0xaaaaaaaa, /* 1 */
+	0x55555555, /* 2 */
+	0x66555555, /* 3 */
+	0x66556655, /* 4 */
+	0x5a5a5a5a, /* 5 */
+	0x5a5a5aaa, /* 6 */
+	0xaa5a5a5a, /* 7 */
+	0x6a5a5a5a, /* 8 */
+	0x6a5a5aaa, /* 9 */
+	0x6a5a6a5a, /* 10 */
+	0x6a5a6aaa, /* 11 */
+	0x6afa5afa, /* 12 */
+	0xaaaa5aaa, /* 13 */
+	0xaaffffaa, /* 14 */
+	0xaa5555aa, /* 15 */
+	0xfafafafa, /* 16 */
+	0xffffddff, /* 17 */
+	0xdaffdaff, /* 18 */
+	0xfafadafa  /* 19 */
+};
+
+struct rtw89_btc_btf_tlv {
+	u8 type;
+	u8 len;
+	u8 val[1];
+} __packed;
+
+enum btc_btf_set_report_en {
+	RPT_EN_TDMA = BIT(0),
+	RPT_EN_CYCLE = BIT(1),
+	RPT_EN_MREG = BIT(2),
+	RPT_EN_BT_VER_INFO = BIT(3),
+	RPT_EN_BT_SCAN_INFO = BIT(4),
+	RPT_EN_BT_AFH_MAP = BIT(5),
+	RPT_EN_BT_DEVICE_INFO = BIT(6),
+	RPT_EN_WL_ALL = GENMASK(2, 0),
+	RPT_EN_BT_ALL = GENMASK(6, 3),
+	RPT_EN_ALL = GENMASK(6, 0),
+};
+
+#define BTF_SET_REPORT_VER 1
+struct rtw89_btc_btf_set_report {
+	u8 fver;
+	__le32 enable;
+	__le32 para;
+} __packed;
+
+#define BTF_SET_SLOT_TABLE_VER 1
+struct rtw89_btc_btf_set_slot_table {
+	u8 fver;
+	u8 tbl_num;
+	u8 buf[];
+} __packed;
+
+#define BTF_SET_MON_REG_VER 1
+struct rtw89_btc_btf_set_mon_reg {
+	u8 fver;
+	u8 reg_num;
+	u8 buf[];
+} __packed;
+
+enum btc_btf_set_cx_policy {
+	CXPOLICY_TDMA = 0x0,
+	CXPOLICY_SLOT = 0x1,
+	CXPOLICY_TYPE = 0x2,
+	CXPOLICY_MAX,
+};
+
+enum btc_b2w_scoreboard {
+	BTC_BSCB_ACT = BIT(0),
+	BTC_BSCB_ON = BIT(1),
+	BTC_BSCB_WHQL = BIT(2),
+	BTC_BSCB_BT_S1 = BIT(3),
+	BTC_BSCB_A2DP_ACT = BIT(4),
+	BTC_BSCB_RFK_RUN = BIT(5),
+	BTC_BSCB_RFK_REQ = BIT(6),
+	BTC_BSCB_LPS = BIT(7),
+	BTC_BSCB_WLRFK = BIT(11),
+	BTC_BSCB_BT_HILNA = BIT(13),
+	BTC_BSCB_BT_CONNECT = BIT(16),
+	BTC_BSCB_PATCH_CODE = BIT(30),
+	BTC_BSCB_ALL = GENMASK(30, 0),
+};
+
+enum btc_phymap {
+	BTC_PHY_0 = BIT(0),
+	BTC_PHY_1 = BIT(1),
+	BTC_PHY_ALL = BIT(0) | BIT(1),
+};
+
+enum btc_cx_state_map {
+	BTC_WIDLE = 0,
+	BTC_WBUSY_BNOSCAN,
+	BTC_WBUSY_BSCAN,
+	BTC_WSCAN_BNOSCAN,
+	BTC_WSCAN_BSCAN,
+	BTC_WLINKING
+};
+
+enum btc_ant_phase {
+	BTC_ANT_WPOWERON = 0,
+	BTC_ANT_WINIT,
+	BTC_ANT_WONLY,
+	BTC_ANT_WOFF,
+	BTC_ANT_W2G,
+	BTC_ANT_W5G,
+	BTC_ANT_W25G,
+	BTC_ANT_FREERUN,
+	BTC_ANT_WRFK,
+	BTC_ANT_BRFK,
+	BTC_ANT_MAX
+};
+
+enum btc_plt {
+	BTC_PLT_NONE = 0,
+	BTC_PLT_LTE_RX = BIT(0),
+	BTC_PLT_GNT_BT_TX = BIT(1),
+	BTC_PLT_GNT_BT_RX = BIT(2),
+	BTC_PLT_GNT_WL = BIT(3),
+	BTC_PLT_BT = BIT(1) | BIT(2),
+	BTC_PLT_ALL = 0xf
+};
+
+enum btc_cx_poicy_main_type {
+	BTC_CXP_OFF = 0,
+	BTC_CXP_OFFB,
+	BTC_CXP_OFFE,
+	BTC_CXP_FIX,
+	BTC_CXP_PFIX,
+	BTC_CXP_AUTO,
+	BTC_CXP_PAUTO,
+	BTC_CXP_AUTO2,
+	BTC_CXP_PAUTO2,
+	BTC_CXP_MANUAL,
+	BTC_CXP_USERDEF0,
+	BTC_CXP_MAIN_MAX
+};
+
+enum btc_cx_poicy_type {
+	/* TDMA off + pri: BT > WL */
+	BTC_CXP_OFF_BT = (BTC_CXP_OFF << 8) | 0,
+
+	/* TDMA off + pri: WL > BT */
+	BTC_CXP_OFF_WL = (BTC_CXP_OFF << 8) | 1,
+
+	/* TDMA off + pri: BT = WL */
+	BTC_CXP_OFF_EQ0 = (BTC_CXP_OFF << 8) | 2,
+
+	/* TDMA off + pri: BT = WL > BT_Lo */
+	BTC_CXP_OFF_EQ1 = (BTC_CXP_OFF << 8) | 3,
+
+	/* TDMA off + pri: WL = BT, BT_Rx > WL_Lo_Tx */
+	BTC_CXP_OFF_EQ2 = (BTC_CXP_OFF << 8) | 4,
+
+	/* TDMA off + pri: WL_Rx = BT, BT_HI > WL_Tx > BT_Lo */
+	BTC_CXP_OFF_EQ3 = (BTC_CXP_OFF << 8) | 5,
+
+	/* TDMA off + pri: BT_Hi > WL > BT_Lo */
+	BTC_CXP_OFF_BWB0 = (BTC_CXP_OFF << 8) | 6,
+
+	/* TDMA off + pri: WL_Hi-Tx > BT_Hi_Rx, BT_Hi > WL > BT_Lo */
+	BTC_CXP_OFF_BWB1 = (BTC_CXP_OFF << 8) | 7,
+
+	/* TDMA off+Bcn-Protect + pri: WL_Hi-Tx > BT_Hi_Rx, BT_Hi > WL > BT_Lo*/
+	BTC_CXP_OFFB_BWB0 = (BTC_CXP_OFFB << 8) | 0,
+
+	/* TDMA off + Ext-Ctrl + pri: default */
+	BTC_CXP_OFFE_DEF = (BTC_CXP_OFFE << 8) | 0,
+
+	/* TDMA off + Ext-Ctrl + pri: E2G-slot block all BT */
+	BTC_CXP_OFFE_DEF2 = (BTC_CXP_OFFE << 8) | 1,
+
+	/* TDMA Fix slot-0: W1:B1 = 30:30 */
+	BTC_CXP_FIX_TD3030 = (BTC_CXP_FIX << 8) | 0,
+
+	/* TDMA Fix slot-1: W1:B1 = 50:50 */
+	BTC_CXP_FIX_TD5050 = (BTC_CXP_FIX << 8) | 1,
+
+	/* TDMA Fix slot-2: W1:B1 = 20:30 */
+	BTC_CXP_FIX_TD2030 = (BTC_CXP_FIX << 8) | 2,
+
+	/* TDMA Fix slot-3: W1:B1 = 40:10 */
+	BTC_CXP_FIX_TD4010 = (BTC_CXP_FIX << 8) | 3,
+
+	/* TDMA Fix slot-4: W1:B1 = 70:10 */
+	BTC_CXP_FIX_TD7010 = (BTC_CXP_FIX << 8) | 4,
+
+	/* TDMA Fix slot-5: W1:B1 = 20:60 */
+	BTC_CXP_FIX_TD2060 = (BTC_CXP_FIX << 8) | 5,
+
+	/* TDMA Fix slot-6: W1:B1 = 30:60 */
+	BTC_CXP_FIX_TD3060 = (BTC_CXP_FIX << 8) | 6,
+
+	/* TDMA Fix slot-7: W1:B1 = 20:80 */
+	BTC_CXP_FIX_TD2080 = (BTC_CXP_FIX << 8) | 7,
+
+	/* TDMA Fix slot-8: W1:B1 = user-define */
+	BTC_CXP_FIX_TDW1B1 = (BTC_CXP_FIX << 8) | 8,
+
+	/* TDMA Fix slot-9: W1:B1 = 40:20 */
+	BTC_CXP_FIX_TD4020 = (BTC_CXP_FIX << 8) | 9,
+
+	/* PS-TDMA Fix slot-0: W1:B1 = 30:30 */
+	BTC_CXP_PFIX_TD3030 = (BTC_CXP_PFIX << 8) | 0,
+
+	/* PS-TDMA Fix slot-1: W1:B1 = 50:50 */
+	BTC_CXP_PFIX_TD5050 = (BTC_CXP_PFIX << 8) | 1,
+
+	/* PS-TDMA Fix slot-2: W1:B1 = 20:30 */
+	BTC_CXP_PFIX_TD2030 = (BTC_CXP_PFIX << 8) | 2,
+
+	/* PS-TDMA Fix slot-3: W1:B1 = 20:60 */
+	BTC_CXP_PFIX_TD2060 = (BTC_CXP_PFIX << 8) | 3,
+
+	/* PS-TDMA Fix slot-4: W1:B1 = 30:70 */
+	BTC_CXP_PFIX_TD3070 = (BTC_CXP_PFIX << 8) | 4,
+
+	/* PS-TDMA Fix slot-5: W1:B1 = 20:80 */
+	BTC_CXP_PFIX_TD2080 = (BTC_CXP_PFIX << 8) | 5,
+
+	/* PS-TDMA Fix slot-6: W1:B1 = user-define */
+	BTC_CXP_PFIX_TDW1B1 = (BTC_CXP_PFIX << 8) | 6,
+
+	/* TDMA Auto slot-0: W1:B1 = 50:200 */
+	BTC_CXP_AUTO_TD50200 = (BTC_CXP_AUTO << 8) | 0,
+
+	/* TDMA Auto slot-1: W1:B1 = 60:200 */
+	BTC_CXP_AUTO_TD60200 = (BTC_CXP_AUTO << 8) | 1,
+
+	/* TDMA Auto slot-2: W1:B1 = 20:200 */
+	BTC_CXP_AUTO_TD20200 = (BTC_CXP_AUTO << 8) | 2,
+
+	/* TDMA Auto slot-3: W1:B1 = user-define */
+	BTC_CXP_AUTO_TDW1B1 = (BTC_CXP_AUTO << 8) | 3,
+
+	/* PS-TDMA Auto slot-0: W1:B1 = 50:200 */
+	BTC_CXP_PAUTO_TD50200 = (BTC_CXP_PAUTO << 8) | 0,
+
+	/* PS-TDMA Auto slot-1: W1:B1 = 60:200 */
+	BTC_CXP_PAUTO_TD60200 = (BTC_CXP_PAUTO << 8) | 1,
+
+	/* PS-TDMA Auto slot-2: W1:B1 = 20:200 */
+	BTC_CXP_PAUTO_TD20200 = (BTC_CXP_PAUTO << 8) | 2,
+
+	/* PS-TDMA Auto slot-3: W1:B1 = user-define */
+	BTC_CXP_PAUTO_TDW1B1 = (BTC_CXP_PAUTO << 8) | 3,
+
+	/* TDMA Auto slot2-0: W1:B4 = 30:50 */
+	BTC_CXP_AUTO2_TD3050 = (BTC_CXP_AUTO2 << 8) | 0,
+
+	/* TDMA Auto slot2-1: W1:B4 = 30:70 */
+	BTC_CXP_AUTO2_TD3070 = (BTC_CXP_AUTO2 << 8) | 1,
+
+	/* TDMA Auto slot2-2: W1:B4 = 50:50 */
+	BTC_CXP_AUTO2_TD5050 = (BTC_CXP_AUTO2 << 8) | 2,
+
+	/* TDMA Auto slot2-3: W1:B4 = 60:60 */
+	BTC_CXP_AUTO2_TD6060 = (BTC_CXP_AUTO2 << 8) | 3,
+
+	/* TDMA Auto slot2-4: W1:B4 = 20:80 */
+	BTC_CXP_AUTO2_TD2080 = (BTC_CXP_AUTO2 << 8) | 4,
+
+	/* TDMA Auto slot2-5: W1:B4 = user-define */
+	BTC_CXP_AUTO2_TDW1B4 = (BTC_CXP_AUTO2 << 8) | 5,
+
+	/* PS-TDMA Auto slot2-0: W1:B4 = 30:50 */
+	BTC_CXP_PAUTO2_TD3050 = (BTC_CXP_PAUTO2 << 8) | 0,
+
+	/* PS-TDMA Auto slot2-1: W1:B4 = 30:70 */
+	BTC_CXP_PAUTO2_TD3070 = (BTC_CXP_PAUTO2 << 8) | 1,
+
+	/* PS-TDMA Auto slot2-2: W1:B4 = 50:50 */
+	BTC_CXP_PAUTO2_TD5050 = (BTC_CXP_PAUTO2 << 8) | 2,
+
+	/* PS-TDMA Auto slot2-3: W1:B4 = 60:60 */
+	BTC_CXP_PAUTO2_TD6060 = (BTC_CXP_PAUTO2 << 8) | 3,
+
+	/* PS-TDMA Auto slot2-4: W1:B4 = 20:80 */
+	BTC_CXP_PAUTO2_TD2080 = (BTC_CXP_PAUTO2 << 8) | 4,
+
+	/* PS-TDMA Auto slot2-5: W1:B4 = user-define */
+	BTC_CXP_PAUTO2_TDW1B4 = (BTC_CXP_PAUTO2 << 8) | 5,
+
+	BTC_CXP_MAX = 0xffff
+};
+
+enum btc_wl_rfk_result {
+	BTC_WRFK_REJECT = 0,
+	BTC_WRFK_ALLOW = 1,
+};
+
+enum btc_coex_info_map_en {
+	BTC_COEX_INFO_CX = BIT(0),
+	BTC_COEX_INFO_WL = BIT(1),
+	BTC_COEX_INFO_BT = BIT(2),
+	BTC_COEX_INFO_DM = BIT(3),
+	BTC_COEX_INFO_MREG = BIT(4),
+	BTC_COEX_INFO_SUMMARY = BIT(5),
+	BTC_COEX_INFO_ALL = GENMASK(7, 0),
+};
+
+#define BTC_CXP_MASK GENMASK(15, 8)
+
+enum btc_w2b_scoreboard {
+	BTC_WSCB_ACTIVE = BIT(0),
+	BTC_WSCB_ON = BIT(1),
+	BTC_WSCB_SCAN = BIT(2),
+	BTC_WSCB_UNDERTEST = BIT(3),
+	BTC_WSCB_RXGAIN = BIT(4),
+	BTC_WSCB_WLBUSY = BIT(7),
+	BTC_WSCB_EXTFEM = BIT(8),
+	BTC_WSCB_TDMA = BIT(9),
+	BTC_WSCB_FIX2M = BIT(10),
+	BTC_WSCB_WLRFK = BIT(11),
+	BTC_WSCB_BTRFK_GNT = BIT(12), /* not used, use mailbox to inform BT */
+	BTC_WSCB_BT_HILNA = BIT(13),
+	BTC_WSCB_BTLOG = BIT(14),
+	BTC_WSCB_ALL = GENMASK(23, 0),
+};
+
+enum btc_wl_link_mode {
+	BTC_WLINK_NOLINK = 0x0,
+	BTC_WLINK_2G_STA,
+	BTC_WLINK_2G_AP,
+	BTC_WLINK_2G_GO,
+	BTC_WLINK_2G_GC,
+	BTC_WLINK_2G_SCC,
+	BTC_WLINK_2G_MCC,
+	BTC_WLINK_25G_MCC,
+	BTC_WLINK_25G_DBCC,
+	BTC_WLINK_5G,
+	BTC_WLINK_2G_NAN,
+	BTC_WLINK_OTHER,
+	BTC_WLINK_MAX
+};
+
+enum btc_bt_hid_type {
+	BTC_HID_218 = BIT(0),
+	BTC_HID_418 = BIT(1),
+	BTC_HID_BLE = BIT(2),
+	BTC_HID_RCU = BIT(3),
+	BTC_HID_RCU_VOICE = BIT(4),
+	BTC_HID_OTHER_LEGACY = BIT(5)
+};
+
+enum btc_reset_module {
+	BTC_RESET_CX = BIT(0),
+	BTC_RESET_DM = BIT(1),
+	BTC_RESET_CTRL = BIT(2),
+	BTC_RESET_CXDM = BIT(0) | BIT(1),
+	BTC_RESET_BTINFO = BIT(3),
+	BTC_RESET_MDINFO = BIT(4),
+	BTC_RESET_ALL =  GENMASK(7, 0),
+};
+
+enum btc_gnt_state {
+	BTC_GNT_HW	= 0,
+	BTC_GNT_SW_LO,
+	BTC_GNT_SW_HI,
+	BTC_GNT_MAX
+};
+
+enum btc_wl_max_tx_time {
+	BTC_MAX_TX_TIME_L1 = 500,
+	BTC_MAX_TX_TIME_L2 = 1000,
+	BTC_MAX_TX_TIME_L3 = 2000,
+	BTC_MAX_TX_TIME_DEF = 5280
+};
+
+enum btc_wl_max_tx_retry {
+	BTC_MAX_TX_RETRY_L1 = 7,
+	BTC_MAX_TX_RETRY_L2 = 15,
+	BTC_MAX_TX_RETRY_DEF = 31,
+};
+
+enum btc_reason_and_action {
+	BTC_RSN_NONE,
+	BTC_RSN_NTFY_INIT,
+	BTC_RSN_NTFY_SWBAND,
+	BTC_RSN_NTFY_WL_STA,
+	BTC_RSN_NTFY_RADIO_STATE,
+	BTC_RSN_UPDATE_BT_SCBD,
+	BTC_RSN_NTFY_WL_RFK,
+	BTC_RSN_UPDATE_BT_INFO,
+	BTC_RSN_NTFY_SCAN_START,
+	BTC_RSN_NTFY_SCAN_FINISH,
+	BTC_RSN_NTFY_SPECIFIC_PACKET,
+	BTC_RSN_NTFY_POWEROFF,
+	BTC_RSN_NTFY_ROLE_INFO,
+	BTC_RSN_CMD_SET_COEX,
+	BTC_RSN_ACT1_WORK,
+	BTC_RSN_BT_DEVINFO_WORK,
+	BTC_RSN_RFK_CHK_WORK,
+	BTC_RSN_NUM,
+	BTC_ACT_NONE = 100,
+	BTC_ACT_WL_ONLY,
+	BTC_ACT_WL_5G,
+	BTC_ACT_WL_OTHER,
+	BTC_ACT_WL_IDLE,
+	BTC_ACT_WL_NC,
+	BTC_ACT_WL_RFK,
+	BTC_ACT_WL_INIT,
+	BTC_ACT_WL_OFF,
+	BTC_ACT_FREERUN,
+	BTC_ACT_BT_WHQL,
+	BTC_ACT_BT_RFK,
+	BTC_ACT_BT_OFF,
+	BTC_ACT_BT_IDLE,
+	BTC_ACT_BT_HFP,
+	BTC_ACT_BT_HID,
+	BTC_ACT_BT_A2DP,
+	BTC_ACT_BT_A2DPSINK,
+	BTC_ACT_BT_PAN,
+	BTC_ACT_BT_A2DP_HID,
+	BTC_ACT_BT_A2DP_PAN,
+	BTC_ACT_BT_PAN_HID,
+	BTC_ACT_BT_A2DP_PAN_HID,
+	BTC_ACT_WL_25G_MCC,
+	BTC_ACT_WL_2G_MCC,
+	BTC_ACT_WL_2G_SCC,
+	BTC_ACT_WL_2G_AP,
+	BTC_ACT_WL_2G_GO,
+	BTC_ACT_WL_2G_GC,
+	BTC_ACT_WL_2G_NAN,
+	BTC_ACT_LAST,
+	BTC_ACT_NUM = BTC_ACT_LAST - BTC_ACT_NONE,
+	BTC_ACT_EXT_BIT = BIT(14),
+	BTC_POLICY_EXT_BIT = BIT(15),
+};
+
+#define BTC_FREERUN_ANTISO_MIN 30
+#define BTC_TDMA_BTHID_MAX 2
+#define BTC_BLINK_NOCONNECT 0
+
+static void _run_coex(struct rtw89_dev *rtwdev,
+		      enum btc_reason_and_action reason);
+static void _write_scbd(struct rtw89_dev *rtwdev, u32 val, bool state);
+static void _update_bt_scbd(struct rtw89_dev *rtwdev, bool only_update);
+
+static void _send_fw_cmd(struct rtw89_dev *rtwdev, u8 h2c_class, u8 h2c_func,
+			 void *param, u16 len)
+{
+	rtw89_fw_h2c_raw_with_hdr(rtwdev, h2c_class, h2c_func, param, len,
+				  false, true);
+}
+
+static void _reset_btc_var(struct rtw89_dev *rtwdev, u8 type)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_bt_link_info *bt_linfo = &bt->link_info;
+	struct rtw89_btc_wl_link_info *wl_linfo = wl->link_info;
+	u8 i;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s\n", __func__);
+
+	if (type & BTC_RESET_CX)
+		memset(cx, 0, sizeof(*cx));
+	else if (type & BTC_RESET_BTINFO) /* only for BT enable */
+		memset(bt, 0, sizeof(*bt));
+
+	if (type & BTC_RESET_CTRL) {
+		memset(&btc->ctrl, 0, sizeof(btc->ctrl));
+		btc->ctrl.trace_step = FCXDEF_STEP;
+	}
+
+	/* Init Coex variables that are not zero */
+	if (type & BTC_RESET_DM) {
+		memset(&btc->dm, 0, sizeof(btc->dm));
+		memset(bt_linfo->rssi_state, 0, sizeof(bt_linfo->rssi_state));
+
+		for (i = 0; i < RTW89_MAX_HW_PORT_NUM; i++)
+			memset(wl_linfo[i].rssi_state, 0,
+			       sizeof(wl_linfo[i].rssi_state));
+
+		/* set the slot_now table to original */
+		btc->dm.tdma_now = t_def[CXTD_OFF];
+		btc->dm.tdma = t_def[CXTD_OFF];
+		memcpy(&btc->dm.slot_now, s_def, sizeof(btc->dm.slot_now));
+		memcpy(&btc->dm.slot, s_def, sizeof(btc->dm.slot));
+
+		btc->policy_len = 0;
+		btc->bt_req_len = 0;
+
+		btc->dm.coex_info_map = BTC_COEX_INFO_ALL;
+		btc->dm.wl_tx_limit.tx_time = BTC_MAX_TX_TIME_DEF;
+		btc->dm.wl_tx_limit.tx_retry = BTC_MAX_TX_RETRY_DEF;
+	}
+
+	if (type & BTC_RESET_MDINFO)
+		memset(&btc->mdinfo, 0, sizeof(btc->mdinfo));
+}
+
+#define BTC_FWINFO_BUF 1024
+
+#define BTC_RPT_HDR_SIZE 3
+#define BTC_CHK_WLSLOT_DRIFT_MAX 15
+#define BTC_CHK_HANG_MAX 3
+
+static void _chk_btc_err(struct rtw89_dev *rtwdev, u8 type, u32 cnt)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): type:%d cnt:%d\n",
+		    __func__, type, cnt);
+
+	switch (type) {
+	case BTC_DCNT_RPT_FREEZE:
+		if (dm->cnt_dm[BTC_DCNT_RPT] == cnt && btc->fwinfo.rpt_en_map)
+			dm->cnt_dm[BTC_DCNT_RPT_FREEZE]++;
+		else
+			dm->cnt_dm[BTC_DCNT_RPT_FREEZE] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_RPT_FREEZE] >= BTC_CHK_HANG_MAX)
+			dm->error.map.wl_fw_hang = true;
+		else
+			dm->error.map.wl_fw_hang = false;
+
+		dm->cnt_dm[BTC_DCNT_RPT] = cnt;
+		break;
+	case BTC_DCNT_CYCLE_FREEZE:
+		if (dm->cnt_dm[BTC_DCNT_CYCLE] == cnt &&
+		    (dm->tdma_now.type != CXTDMA_OFF ||
+		     dm->tdma_now.ext_ctrl == CXECTL_EXT))
+			dm->cnt_dm[BTC_DCNT_CYCLE_FREEZE]++;
+		else
+			dm->cnt_dm[BTC_DCNT_CYCLE_FREEZE] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_CYCLE_FREEZE] >= BTC_CHK_HANG_MAX)
+			dm->error.map.cycle_hang = true;
+		else
+			dm->error.map.cycle_hang = false;
+
+		dm->cnt_dm[BTC_DCNT_CYCLE] = cnt;
+		break;
+	case BTC_DCNT_W1_FREEZE:
+		if (dm->cnt_dm[BTC_DCNT_W1] == cnt &&
+		    dm->tdma_now.type != CXTDMA_OFF)
+			dm->cnt_dm[BTC_DCNT_W1_FREEZE]++;
+		else
+			dm->cnt_dm[BTC_DCNT_W1_FREEZE] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_W1_FREEZE] >= BTC_CHK_HANG_MAX)
+			dm->error.map.w1_hang = true;
+		else
+			dm->error.map.w1_hang = false;
+
+		dm->cnt_dm[BTC_DCNT_W1] = cnt;
+		break;
+	case BTC_DCNT_B1_FREEZE:
+		if (dm->cnt_dm[BTC_DCNT_B1] == cnt &&
+		    dm->tdma_now.type != CXTDMA_OFF)
+			dm->cnt_dm[BTC_DCNT_B1_FREEZE]++;
+		else
+			dm->cnt_dm[BTC_DCNT_B1_FREEZE] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_B1_FREEZE] >= BTC_CHK_HANG_MAX)
+			dm->error.map.b1_hang = true;
+		else
+			dm->error.map.b1_hang = false;
+
+		dm->cnt_dm[BTC_DCNT_B1] = cnt;
+		break;
+	case BTC_DCNT_TDMA_NONSYNC:
+		if (cnt != 0) /* if tdma not sync between drv/fw  */
+			dm->cnt_dm[BTC_DCNT_TDMA_NONSYNC]++;
+		else
+			dm->cnt_dm[BTC_DCNT_TDMA_NONSYNC] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_TDMA_NONSYNC] >= BTC_CHK_HANG_MAX)
+			dm->error.map.tdma_no_sync = true;
+		else
+			dm->error.map.tdma_no_sync = false;
+		break;
+	case BTC_DCNT_SLOT_NONSYNC:
+		if (cnt != 0) /* if slot not sync between drv/fw  */
+			dm->cnt_dm[BTC_DCNT_SLOT_NONSYNC]++;
+		else
+			dm->cnt_dm[BTC_DCNT_SLOT_NONSYNC] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_SLOT_NONSYNC] >= BTC_CHK_HANG_MAX)
+			dm->error.map.tdma_no_sync = true;
+		else
+			dm->error.map.tdma_no_sync = false;
+		break;
+	case BTC_DCNT_BTCNT_FREEZE:
+		cnt = cx->cnt_bt[BTC_BCNT_HIPRI_RX] +
+		      cx->cnt_bt[BTC_BCNT_HIPRI_TX] +
+		      cx->cnt_bt[BTC_BCNT_LOPRI_RX] +
+		      cx->cnt_bt[BTC_BCNT_LOPRI_TX];
+
+		if (cnt == 0)
+			dm->cnt_dm[BTC_DCNT_BTCNT_FREEZE]++;
+		else
+			dm->cnt_dm[BTC_DCNT_BTCNT_FREEZE] = 0;
+
+		if ((dm->cnt_dm[BTC_DCNT_BTCNT_FREEZE] >= BTC_CHK_HANG_MAX &&
+		     bt->enable.now) || (!dm->cnt_dm[BTC_DCNT_BTCNT_FREEZE] &&
+		     !bt->enable.now))
+			_update_bt_scbd(rtwdev, false);
+		break;
+	case BTC_DCNT_WL_SLOT_DRIFT:
+		if (cnt >= BTC_CHK_WLSLOT_DRIFT_MAX)
+			dm->cnt_dm[BTC_DCNT_WL_SLOT_DRIFT]++;
+		else
+			dm->cnt_dm[BTC_DCNT_WL_SLOT_DRIFT] = 0;
+
+		if (dm->cnt_dm[BTC_DCNT_WL_SLOT_DRIFT] >= BTC_CHK_HANG_MAX)
+			dm->error.map.wl_slot_drift = true;
+		else
+			dm->error.map.wl_slot_drift = false;
+		break;
+	}
+}
+
+static void _update_bt_report(struct rtw89_dev *rtwdev, u8 rpt_type, u8 *pfinfo)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_bt_link_info *bt_linfo = &bt->link_info;
+	struct rtw89_btc_bt_a2dp_desc *a2dp = &bt_linfo->a2dp_desc;
+	struct rtw89_btc_fbtc_btver *pver = NULL;
+	struct rtw89_btc_fbtc_btscan *pscan = NULL;
+	struct rtw89_btc_fbtc_btafh *pafh = NULL;
+	struct rtw89_btc_fbtc_btdevinfo *pdev = NULL;
+
+	pver = (struct rtw89_btc_fbtc_btver *)pfinfo;
+	pscan = (struct rtw89_btc_fbtc_btscan *)pfinfo;
+	pafh = (struct rtw89_btc_fbtc_btafh *)pfinfo;
+	pdev = (struct rtw89_btc_fbtc_btdevinfo *)pfinfo;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): rpt_type:%d\n",
+		    __func__, rpt_type);
+
+	switch (rpt_type) {
+	case BTC_RPT_TYPE_BT_VER:
+		bt->ver_info.fw = le32_to_cpu(pver->fw_ver);
+		bt->ver_info.fw_coex = le32_get_bits(pver->coex_ver, GENMASK(7, 0));
+		bt->feature = le32_to_cpu(pver->feature);
+		break;
+	case BTC_RPT_TYPE_BT_SCAN:
+		memcpy(bt->scan_info, pscan->scan, BTC_SCAN_MAX1);
+		break;
+	case BTC_RPT_TYPE_BT_AFH:
+		memcpy(&bt_linfo->afh_map[0], pafh->afh_l, 4);
+		memcpy(&bt_linfo->afh_map[4], pafh->afh_m, 4);
+		memcpy(&bt_linfo->afh_map[8], pafh->afh_h, 2);
+		break;
+	case BTC_RPT_TYPE_BT_DEVICE:
+		a2dp->device_name = le32_to_cpu(pdev->dev_name);
+		a2dp->vendor_id = le16_to_cpu(pdev->vendor_id);
+		a2dp->flush_time = le32_to_cpu(pdev->flush_time);
+		break;
+	default:
+		break;
+	}
+}
+
+struct rtw89_btc_fbtc_cysta_cpu {
+	u8 fver;
+	u8 rsvd;
+	u16 cycles;
+	u16 cycles_a2dp[CXT_FLCTRL_MAX];
+	u16 a2dpept;
+	u16 a2dpeptto;
+	u16 tavg_cycle[CXT_MAX];
+	u16 tmax_cycle[CXT_MAX];
+	u16 tmaxdiff_cycle[CXT_MAX];
+	u16 tavg_a2dp[CXT_FLCTRL_MAX];
+	u16 tmax_a2dp[CXT_FLCTRL_MAX];
+	u16 tavg_a2dpept;
+	u16 tmax_a2dpept;
+	u16 tavg_lk;
+	u16 tmax_lk;
+	u32 slot_cnt[CXST_MAX];
+	u32 bcn_cnt[CXBCN_MAX];
+	u32 leakrx_cnt;
+	u32 collision_cnt;
+	u32 skip_cnt;
+	u32 exception;
+	u32 except_cnt;
+	u16 tslot_cycle[BTC_CYCLE_SLOT_MAX];
+};
+
+static void rtw89_btc_fbtc_cysta_to_cpu(const struct rtw89_btc_fbtc_cysta *src,
+					struct rtw89_btc_fbtc_cysta_cpu *dst)
+{
+	static_assert(sizeof(*src) == sizeof(*dst));
+
+#define __CPY_U8(_x)	({dst->_x = src->_x; })
+#define __CPY_LE16(_x)	({dst->_x = le16_to_cpu(src->_x); })
+#define __CPY_LE16S(_x)	({int _i; for (_i = 0; _i < ARRAY_SIZE(dst->_x); _i++) \
+				   dst->_x[_i] = le16_to_cpu(src->_x[_i]); })
+#define __CPY_LE32(_x)	({dst->_x = le32_to_cpu(src->_x); })
+#define __CPY_LE32S(_x)	({int _i; for (_i = 0; _i < ARRAY_SIZE(dst->_x); _i++) \
+				   dst->_x[_i] = le32_to_cpu(src->_x[_i]); })
+
+	__CPY_U8(fver);
+	__CPY_U8(rsvd);
+	__CPY_LE16(cycles);
+	__CPY_LE16S(cycles_a2dp);
+	__CPY_LE16(a2dpept);
+	__CPY_LE16(a2dpeptto);
+	__CPY_LE16S(tavg_cycle);
+	__CPY_LE16S(tmax_cycle);
+	__CPY_LE16S(tmaxdiff_cycle);
+	__CPY_LE16S(tavg_a2dp);
+	__CPY_LE16S(tmax_a2dp);
+	__CPY_LE16(tavg_a2dpept);
+	__CPY_LE16(tmax_a2dpept);
+	__CPY_LE16(tavg_lk);
+	__CPY_LE16(tmax_lk);
+	__CPY_LE32S(slot_cnt);
+	__CPY_LE32S(bcn_cnt);
+	__CPY_LE32(leakrx_cnt);
+	__CPY_LE32(collision_cnt);
+	__CPY_LE32(skip_cnt);
+	__CPY_LE32(exception);
+	__CPY_LE32(except_cnt);
+	__CPY_LE16S(tslot_cycle);
+
+#undef __CPY_U8
+#undef __CPY_LE16
+#undef __CPY_LE16S
+#undef __CPY_LE32
+#undef __CPY_LE32S
+}
+
+#define BTC_LEAK_AP_TH 10
+#define BTC_CYSTA_CHK_PERIOD 100
+
+struct rtw89_btc_prpt {
+	u8 type;
+	__le16 len;
+	u8 content[];
+} __packed;
+
+static u32 _chk_btc_report(struct rtw89_dev *rtwdev,
+			   struct rtw89_btc_btf_fwinfo *pfwinfo,
+			   u8 *prptbuf, u32 index)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_fbtc_rpt_ctrl *prpt = NULL;
+	struct rtw89_btc_fbtc_cysta *pcysta_le32 = NULL;
+	struct rtw89_btc_fbtc_cysta_cpu pcysta[1];
+	struct rtw89_btc_prpt *btc_prpt = NULL;
+	struct rtw89_btc_fbtc_slot *rtp_slot = NULL;
+	u8 rpt_type = 0, *rpt_content = NULL, *pfinfo = NULL;
+	u16 wl_slot_set = 0;
+	u32 trace_step = btc->ctrl.trace_step, rpt_len = 0, diff_t;
+	u8 i;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): index:%d\n",
+		    __func__, index);
+
+	if (!prptbuf) {
+		pfwinfo->err[BTFRE_INVALID_INPUT]++;
+		return 0;
+	}
+
+	btc_prpt = (struct rtw89_btc_prpt *)&prptbuf[index];
+	rpt_type = btc_prpt->type;
+	rpt_len = le16_to_cpu(btc_prpt->len);
+	rpt_content = btc_prpt->content;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): rpt_type:%d\n",
+		    __func__, rpt_type);
+
+	switch (rpt_type) {
+	case BTC_RPT_TYPE_CTRL:
+		pcinfo = &pfwinfo->rpt_ctrl.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_ctrl.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_ctrl.finfo);
+		pcinfo->req_fver = BTCRPT_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_TDMA:
+		pcinfo = &pfwinfo->rpt_fbtc_tdma.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_tdma.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_tdma.finfo);
+		pcinfo->req_fver = FCXTDMA_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_SLOT:
+		pcinfo = &pfwinfo->rpt_fbtc_slots.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_slots.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_slots.finfo);
+		pcinfo->req_fver = FCXSLOTS_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_CYSTA:
+		pcinfo = &pfwinfo->rpt_fbtc_cysta.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_cysta.finfo);
+		pcysta_le32 = &pfwinfo->rpt_fbtc_cysta.finfo;
+		rtw89_btc_fbtc_cysta_to_cpu(pcysta_le32, pcysta);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_cysta.finfo);
+		pcinfo->req_fver = FCXCYSTA_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_STEP:
+		pcinfo = &pfwinfo->rpt_fbtc_step.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_step.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_step.finfo.step[0]) *
+				  trace_step + 8;
+		pcinfo->req_fver = FCXSTEP_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_NULLSTA:
+		pcinfo = &pfwinfo->rpt_fbtc_nullsta.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_nullsta.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_nullsta.finfo);
+		pcinfo->req_fver = FCXNULLSTA_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_MREG:
+		pcinfo = &pfwinfo->rpt_fbtc_mregval.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_mregval.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_mregval.finfo);
+		pcinfo->req_fver = FCXMREG_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_GPIO_DBG:
+		pcinfo = &pfwinfo->rpt_fbtc_gpio_dbg.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_gpio_dbg.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_gpio_dbg.finfo);
+		pcinfo->req_fver = FCXGPIODBG_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_BT_VER:
+		pcinfo = &pfwinfo->rpt_fbtc_btver.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_btver.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_btver.finfo);
+		pcinfo->req_fver = FCX_BTVER_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_BT_SCAN:
+		pcinfo = &pfwinfo->rpt_fbtc_btscan.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_btscan.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_btscan.finfo);
+		pcinfo->req_fver = FCX_BTSCAN_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_BT_AFH:
+		pcinfo = &pfwinfo->rpt_fbtc_btafh.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_btafh.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_btafh.finfo);
+		pcinfo->req_fver = FCX_BTAFH_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	case BTC_RPT_TYPE_BT_DEVICE:
+		pcinfo = &pfwinfo->rpt_fbtc_btdev.cinfo;
+		pfinfo = (u8 *)(&pfwinfo->rpt_fbtc_btdev.finfo);
+		pcinfo->req_len = sizeof(pfwinfo->rpt_fbtc_btdev.finfo);
+		pcinfo->req_fver = FCX_BTDEVINFO_VER;
+		pcinfo->rx_len = rpt_len;
+		pcinfo->rx_cnt++;
+		break;
+	default:
+		pfwinfo->err[BTFRE_UNDEF_TYPE]++;
+		return 0;
+	}
+
+	if (rpt_len != pcinfo->req_len) {
+		if (rpt_type < BTC_RPT_TYPE_MAX)
+			pfwinfo->len_mismch |= (0x1 << rpt_type);
+		else
+			pfwinfo->len_mismch |= BIT(31);
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): %d rpt_len:%d!=req_len:%d\n",
+			    __func__, rpt_type, rpt_len, pcinfo->req_len);
+
+		pcinfo->valid = 0;
+		return 0;
+	} else if (!pfinfo || !rpt_content || !pcinfo->req_len) {
+		pfwinfo->err[BTFRE_EXCEPTION]++;
+		pcinfo->valid = 0;
+		return 0;
+	}
+
+	memcpy(pfinfo, rpt_content, pcinfo->req_len);
+	pcinfo->valid = 1;
+
+	if (rpt_type == BTC_RPT_TYPE_TDMA) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): check %d %zu\n", __func__,
+			    BTC_DCNT_TDMA_NONSYNC, sizeof(dm->tdma_now));
+
+		if (memcmp(&dm->tdma_now, &pfwinfo->rpt_fbtc_tdma.finfo,
+			   sizeof(dm->tdma_now)) != 0) {
+			rtw89_debug(rtwdev, RTW89_DBG_BTC,
+				    "[BTC], %s(): %d tdma_now %x %x %x %x %x %x %x %x\n",
+				    __func__, BTC_DCNT_TDMA_NONSYNC,
+				    dm->tdma_now.type, dm->tdma_now.rxflctrl,
+				    dm->tdma_now.txpause, dm->tdma_now.wtgle_n,
+				    dm->tdma_now.leak_n, dm->tdma_now.ext_ctrl,
+				    dm->tdma_now.rsvd0, dm->tdma_now.rsvd1);
+
+			rtw89_debug(rtwdev, RTW89_DBG_BTC,
+				    "[BTC], %s(): %d rpt_fbtc_tdma %x %x %x %x %x %x %x %x\n",
+				    __func__, BTC_DCNT_TDMA_NONSYNC,
+				    pfwinfo->rpt_fbtc_tdma.finfo.type,
+				    pfwinfo->rpt_fbtc_tdma.finfo.rxflctrl,
+				    pfwinfo->rpt_fbtc_tdma.finfo.txpause,
+				    pfwinfo->rpt_fbtc_tdma.finfo.wtgle_n,
+				    pfwinfo->rpt_fbtc_tdma.finfo.leak_n,
+				    pfwinfo->rpt_fbtc_tdma.finfo.ext_ctrl,
+				    pfwinfo->rpt_fbtc_tdma.finfo.rsvd0,
+				    pfwinfo->rpt_fbtc_tdma.finfo.rsvd1);
+		}
+
+		_chk_btc_err(rtwdev, BTC_DCNT_TDMA_NONSYNC,
+			     memcmp(&dm->tdma_now,
+				    &pfwinfo->rpt_fbtc_tdma.finfo,
+				    sizeof(dm->tdma_now)));
+	}
+
+	if (rpt_type == BTC_RPT_TYPE_SLOT) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): check %d %zu\n",
+			    __func__, BTC_DCNT_SLOT_NONSYNC,
+			    sizeof(dm->slot_now));
+
+		if (memcmp(dm->slot_now, pfwinfo->rpt_fbtc_slots.finfo.slot,
+			   sizeof(dm->slot_now)) != 0) {
+			for (i = 0; i < CXST_MAX; i++) {
+				rtp_slot =
+				&pfwinfo->rpt_fbtc_slots.finfo.slot[i];
+				if (memcmp(&dm->slot_now[i], rtp_slot,
+					   sizeof(dm->slot_now[i])) != 0) {
+					rtw89_debug(rtwdev, RTW89_DBG_BTC,
+						    "[BTC], %s(): %d slot_now[%d] dur=0x%04x tbl=%08x type=0x%04x\n",
+						    __func__,
+						    BTC_DCNT_SLOT_NONSYNC, i,
+						    dm->slot_now[i].dur,
+						    dm->slot_now[i].cxtbl,
+						    dm->slot_now[i].cxtype);
+
+					rtw89_debug(rtwdev, RTW89_DBG_BTC,
+						    "[BTC], %s(): %d rpt_fbtc_slots[%d] dur=0x%04x tbl=%08x type=0x%04x\n",
+						    __func__,
+						    BTC_DCNT_SLOT_NONSYNC, i,
+						    rtp_slot->dur,
+						    rtp_slot->cxtbl,
+						    rtp_slot->cxtype);
+				}
+			}
+		}
+		_chk_btc_err(rtwdev, BTC_DCNT_SLOT_NONSYNC,
+			     memcmp(dm->slot_now,
+				    pfwinfo->rpt_fbtc_slots.finfo.slot,
+				    sizeof(dm->slot_now)));
+	}
+
+	if (rpt_type == BTC_RPT_TYPE_CYSTA &&
+	    pcysta->cycles >= BTC_CYSTA_CHK_PERIOD) {
+		/* Check Leak-AP */
+		if (pcysta->slot_cnt[CXST_LK] != 0 &&
+		    pcysta->leakrx_cnt != 0 && dm->tdma_now.rxflctrl) {
+			if (pcysta->slot_cnt[CXST_LK] <
+			    BTC_LEAK_AP_TH * pcysta->leakrx_cnt)
+				dm->leak_ap = 1;
+		}
+
+		/* Check diff time between WL slot and W1/E2G slot */
+		if (dm->tdma_now.type == CXTDMA_OFF &&
+		    dm->tdma_now.ext_ctrl == CXECTL_EXT)
+			wl_slot_set = le16_to_cpu(dm->slot_now[CXST_E2G].dur);
+		else
+			wl_slot_set = le16_to_cpu(dm->slot_now[CXST_W1].dur);
+
+		if (pcysta->tavg_cycle[CXT_WL] > wl_slot_set) {
+			diff_t = pcysta->tavg_cycle[CXT_WL] - wl_slot_set;
+			_chk_btc_err(rtwdev, BTC_DCNT_WL_SLOT_DRIFT, diff_t);
+		}
+	}
+
+	if (rpt_type == BTC_RPT_TYPE_CTRL) {
+		prpt = &pfwinfo->rpt_ctrl.finfo;
+		btc->fwinfo.rpt_en_map = prpt->rpt_enable;
+		wl->ver_info.fw_coex = prpt->wl_fw_coex_ver;
+		wl->ver_info.fw = prpt->wl_fw_ver;
+		dm->wl_fw_cx_offload = !!(prpt->wl_fw_cx_offload);
+	}
+
+	if (rpt_type >= BTC_RPT_TYPE_BT_VER &&
+	    rpt_type <= BTC_RPT_TYPE_BT_DEVICE)
+		_update_bt_report(rtwdev, rpt_type, pfinfo);
+
+	return (rpt_len + BTC_RPT_HDR_SIZE);
+}
+
+static void _parse_btc_report(struct rtw89_dev *rtwdev,
+			      struct rtw89_btc_btf_fwinfo *pfwinfo,
+			      u8 *pbuf, u32 buf_len)
+{
+	struct rtw89_btc_prpt *btc_prpt = NULL;
+	u32 index = 0, rpt_len = 0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): buf_len:%d\n",
+		    __func__, buf_len);
+
+	while (pbuf) {
+		btc_prpt = (struct rtw89_btc_prpt *)&pbuf[index];
+		if (index + 2 >= BTC_FWINFO_BUF)
+			break;
+		/* At least 3 bytes: type(1) & len(2) */
+		rpt_len = le16_to_cpu(btc_prpt->len);
+		if ((index + rpt_len + BTC_RPT_HDR_SIZE) > buf_len)
+			break;
+
+		rpt_len = _chk_btc_report(rtwdev, pfwinfo, pbuf, index);
+		if (!rpt_len)
+			break;
+		index += rpt_len;
+	}
+}
+
+#define BTC_TLV_HDR_LEN 2
+
+static void _append_tdma(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_btf_tlv *tlv = NULL;
+	struct rtw89_btc_fbtc_tdma *v = NULL;
+	u16 len = btc->policy_len;
+
+	if (!btc->update_policy_force &&
+	    !memcmp(&dm->tdma, &dm->tdma_now, sizeof(dm->tdma))) {
+		rtw89_debug(rtwdev,
+			    RTW89_DBG_BTC, "[BTC], %s(): tdma no change!\n",
+			    __func__);
+		return;
+	}
+
+	tlv = (struct rtw89_btc_btf_tlv *)&btc->policy[len];
+	v = (struct rtw89_btc_fbtc_tdma *)&tlv->val[0];
+	tlv->type = CXPOLICY_TDMA;
+	tlv->len = sizeof(*v);
+
+	memcpy(v, &dm->tdma, sizeof(*v));
+	btc->policy_len += BTC_TLV_HDR_LEN  + sizeof(*v);
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): type:%d, rxflctrl=%d, txpause=%d, wtgle_n=%d, leak_n=%d, ext_ctrl=%d\n",
+		    __func__, dm->tdma.type, dm->tdma.rxflctrl,
+		    dm->tdma.txpause, dm->tdma.wtgle_n, dm->tdma.leak_n,
+		    dm->tdma.ext_ctrl);
+}
+
+static void _append_slot(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_btf_tlv *tlv = NULL;
+	struct btc_fbtc_1slot *v = NULL;
+	u16 len = 0;
+	u8 i, cnt = 0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): A:btc->policy_len = %d\n",
+		    __func__, btc->policy_len);
+
+	for (i = 0; i < CXST_MAX; i++) {
+		if (!btc->update_policy_force &&
+		    !memcmp(&dm->slot[i], &dm->slot_now[i],
+			    sizeof(dm->slot[i])))
+			continue;
+
+		len = btc->policy_len;
+
+		tlv = (struct rtw89_btc_btf_tlv *)&btc->policy[len];
+		v = (struct btc_fbtc_1slot *)&tlv->val[0];
+		tlv->type = CXPOLICY_SLOT;
+		tlv->len = sizeof(*v);
+
+		v->fver = FCXONESLOT_VER;
+		v->sid = i;
+		v->slot = dm->slot[i];
+
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): slot-%d: dur=%d, table=0x%08x, type=%d\n",
+			    __func__, i, dm->slot[i].dur, dm->slot[i].cxtbl,
+			    dm->slot[i].cxtype);
+		cnt++;
+
+		btc->policy_len += BTC_TLV_HDR_LEN  + sizeof(*v);
+	}
+
+	if (cnt > 0)
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): slot update (cnt=%d)!!\n",
+			    __func__, cnt);
+}
+
+static void rtw89_btc_fw_en_rpt(struct rtw89_dev *rtwdev,
+				u32 rpt_map, bool rpt_state)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *fwinfo = &btc->fwinfo;
+	struct rtw89_btc_btf_set_report r = {0};
+	u32 val = 0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): rpt_map=%x, rpt_state=%x\n",
+		    __func__, rpt_map, rpt_state);
+
+	if (rpt_state)
+		val = fwinfo->rpt_en_map | rpt_map;
+	else
+		val = fwinfo->rpt_en_map & ~rpt_map;
+
+	if (val == fwinfo->rpt_en_map)
+		return;
+
+	fwinfo->rpt_en_map = val;
+
+	r.fver = BTF_SET_REPORT_VER;
+	r.enable = cpu_to_le32(val);
+	r.para = cpu_to_le32(rpt_state);
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_REPORT_EN, &r, sizeof(r));
+}
+
+static void rtw89_btc_fw_set_slots(struct rtw89_dev *rtwdev, u8 num,
+				   struct rtw89_btc_fbtc_slot *s)
+{
+	struct rtw89_btc_btf_set_slot_table *tbl = NULL;
+	u8 *ptr = NULL;
+	u16 n = 0;
+
+	n = sizeof(*s) * num + sizeof(*tbl);
+	tbl = kmalloc(n, GFP_KERNEL);
+	if (!tbl)
+		return;
+
+	tbl->fver = BTF_SET_SLOT_TABLE_VER;
+	tbl->tbl_num = num;
+	ptr = &tbl->buf[0];
+	memcpy(ptr, s, num * sizeof(*s));
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_SLOT_TABLE, tbl, n);
+
+	kfree(tbl);
+}
+
+static void btc_fw_set_monreg(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc_btf_set_mon_reg *monreg = NULL;
+	u8 n, *ptr = NULL, ulen;
+	u16 sz = 0;
+
+	n = chip->mon_reg_num;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): mon_reg_num=%d\n", __func__, n);
+	if (n > CXMREG_MAX) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): mon reg count %d > %d\n",
+			    __func__, n, CXMREG_MAX);
+		return;
+	}
+
+	ulen = sizeof(struct rtw89_btc_fbtc_mreg);
+	sz = (ulen * n) + sizeof(*monreg);
+	monreg = kmalloc(sz, GFP_KERNEL);
+	if (!monreg)
+		return;
+
+	monreg->fver = BTF_SET_MON_REG_VER;
+	monreg->reg_num = n;
+	ptr = &monreg->buf[0];
+	memcpy(ptr, chip->mon_reg, n * ulen);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): sz=%d ulen=%d n=%d\n",
+		    __func__, sz, ulen, n);
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_MREG_TABLE, (u8 *)monreg, sz);
+	kfree(monreg);
+	rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_MREG, 1);
+}
+
+static void _update_dm_step(struct rtw89_dev *rtwdev,
+			    enum btc_reason_and_action reason_or_action)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+
+	/* use ring-structure to store dm step */
+	dm->dm_step.step[dm->dm_step.step_pos] = reason_or_action;
+	dm->dm_step.step_pos++;
+
+	if (dm->dm_step.step_pos >= ARRAY_SIZE(dm->dm_step.step)) {
+		dm->dm_step.step_pos = 0;
+		dm->dm_step.step_ov = true;
+	}
+}
+
+static void _fw_set_policy(struct rtw89_dev *rtwdev, u16 policy_type,
+			   enum btc_reason_and_action action)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+
+	dm->run_action = action;
+
+	_update_dm_step(rtwdev, action | BTC_ACT_EXT_BIT);
+	_update_dm_step(rtwdev, policy_type | BTC_POLICY_EXT_BIT);
+
+	btc->policy_len = 0;
+	btc->policy_type = policy_type;
+
+	_append_tdma(rtwdev);
+	_append_slot(rtwdev);
+
+	if (btc->policy_len == 0 || btc->policy_len > RTW89_BTC_POLICY_MAXLEN)
+		return;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): action = %d -> policy type/len: 0x%04x/%d\n",
+		    __func__, action, policy_type, btc->policy_len);
+
+	if (dm->tdma.rxflctrl == CXFLC_NULLP ||
+	    dm->tdma.rxflctrl == CXFLC_QOSNULL)
+		btc->lps = 1;
+	else
+		btc->lps = 0;
+
+	if (btc->lps == 1)
+		rtw89_set_coex_ctrl_lps(rtwdev, btc->lps);
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_CX_POLICY,
+		     btc->policy, btc->policy_len);
+
+	memcpy(&dm->tdma_now, &dm->tdma, sizeof(dm->tdma_now));
+	memcpy(&dm->slot_now, &dm->slot, sizeof(dm->slot_now));
+
+	if (btc->update_policy_force)
+		btc->update_policy_force = false;
+
+	if (btc->lps == 0)
+		rtw89_set_coex_ctrl_lps(rtwdev, btc->lps);
+}
+
+static void _fw_set_drv_info(struct rtw89_dev *rtwdev, u8 type)
+{
+	switch (type) {
+	case CXDRVINFO_INIT:
+		rtw89_fw_h2c_cxdrv_init(rtwdev);
+		break;
+	case CXDRVINFO_ROLE:
+		rtw89_fw_h2c_cxdrv_role(rtwdev);
+		break;
+	case CXDRVINFO_CTRL:
+		rtw89_fw_h2c_cxdrv_ctrl(rtwdev);
+		break;
+	case CXDRVINFO_RFK:
+		rtw89_fw_h2c_cxdrv_rfk(rtwdev);
+		break;
+	default:
+		break;
+	}
+}
+
+static
+void btc_fw_event(struct rtw89_dev *rtwdev, u8 evt_id, void *data, u32 len)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): evt_id:%d len:%d\n",
+		    __func__, evt_id, len);
+
+	if (!len || !data)
+		return;
+
+	switch (evt_id) {
+	case BTF_EVNT_RPT:
+		_parse_btc_report(rtwdev, pfwinfo, data, len);
+		break;
+	default:
+		break;
+	}
+}
+
+static void _set_gnt_wl(struct rtw89_dev *rtwdev, u8 phy_map, u8 state)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_mac_ax_gnt *g = dm->gnt.band;
+	u8 i;
+
+	if (phy_map > BTC_PHY_ALL)
+		return;
+
+	for (i = 0; i < RTW89_PHY_MAX; i++) {
+		if (!(phy_map & BIT(i)))
+			continue;
+
+		switch (state) {
+		case BTC_GNT_HW:
+			g[i].gnt_wl_sw_en = 0;
+			g[i].gnt_wl = 0;
+			break;
+		case BTC_GNT_SW_LO:
+			g[i].gnt_wl_sw_en = 1;
+			g[i].gnt_wl = 0;
+			break;
+		case BTC_GNT_SW_HI:
+			g[i].gnt_wl_sw_en = 1;
+			g[i].gnt_wl = 1;
+			break;
+		}
+	}
+
+	rtw89_mac_cfg_gnt(rtwdev, &dm->gnt);
+}
+
+#define BTC_TDMA_WLROLE_MAX 2
+
+static void _set_bt_ignore_wlan_act(struct rtw89_dev *rtwdev, u8 enable)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): set bt %s wlan_act\n", __func__,
+		    enable ? "ignore" : "do not ignore");
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_BT_IGNORE_WLAN_ACT, &enable, 1);
+}
+
+#define WL_TX_POWER_NO_BTC_CTRL	GENMASK(31, 0)
+#define WL_TX_POWER_ALL_TIME GENMASK(15, 0)
+#define WL_TX_POWER_WITH_BT GENMASK(31, 16)
+#define WL_TX_POWER_INT_PART GENMASK(8, 2)
+#define WL_TX_POWER_FRA_PART GENMASK(1, 0)
+#define B_BTC_WL_TX_POWER_SIGN BIT(7)
+#define B_TSSI_WL_TX_POWER_SIGN BIT(8)
+
+static void _set_wl_tx_power(struct rtw89_dev *rtwdev, u32 level)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	u32 pwr_val;
+
+	if (wl->rf_para.tx_pwr_freerun == level)
+		return;
+
+	wl->rf_para.tx_pwr_freerun = level;
+	btc->dm.rf_trx_para.wl_tx_power = level;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): level = %d\n",
+		    __func__, level);
+
+	if (level == RTW89_BTC_WL_DEF_TX_PWR) {
+		pwr_val = WL_TX_POWER_NO_BTC_CTRL;
+	} else { /* only apply "force tx power" */
+		pwr_val = FIELD_PREP(WL_TX_POWER_INT_PART, level);
+		if (pwr_val > RTW89_BTC_WL_DEF_TX_PWR)
+			pwr_val = RTW89_BTC_WL_DEF_TX_PWR;
+
+		if (level & B_BTC_WL_TX_POWER_SIGN)
+			pwr_val |= B_TSSI_WL_TX_POWER_SIGN;
+		pwr_val |= WL_TX_POWER_WITH_BT;
+	}
+
+	chip->ops->btc_set_wl_txpwr_ctrl(rtwdev, pwr_val);
+}
+
+static void _set_wl_rx_gain(struct rtw89_dev *rtwdev, u32 level)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	if (wl->rf_para.rx_gain_freerun == level)
+		return;
+
+	wl->rf_para.rx_gain_freerun = level;
+	btc->dm.rf_trx_para.wl_rx_gain = level;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): level = %d\n",
+		    __func__, level);
+}
+
+static void _set_bt_tx_power(struct rtw89_dev *rtwdev, u8 level)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	u8 buf;
+
+	if (bt->rf_para.tx_pwr_freerun == level)
+		return;
+
+	bt->rf_para.tx_pwr_freerun = level;
+	btc->dm.rf_trx_para.bt_tx_power = level;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): level = %d\n",
+		    __func__, level);
+
+	buf = (s8)(-level);
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_BT_TX_PWR, &buf, 1);
+}
+
+#define BTC_BT_RX_NORMAL_LVL 7
+
+static void _set_bt_rx_gain(struct rtw89_dev *rtwdev, u8 level)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+
+	if (bt->rf_para.rx_gain_freerun == level ||
+	    level > BTC_BT_RX_NORMAL_LVL)
+		return;
+
+	bt->rf_para.rx_gain_freerun = level;
+	btc->dm.rf_trx_para.bt_rx_gain = level;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): level = %d\n",
+		    __func__, level);
+
+	if (level == BTC_BT_RX_NORMAL_LVL)
+		_write_scbd(rtwdev, BTC_WSCB_RXGAIN, false);
+	else
+		_write_scbd(rtwdev, BTC_WSCB_RXGAIN, true);
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_BT_LNA_CONSTRAIN, &level, 1);
+}
+
+static void _set_rf_trx_para(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_rf_trx_para para;
+	u32 wl_stb_chg = 0;
+	u8 level_id = 0;
+
+	if (!dm->freerun) {
+		dm->trx_para_level = 0;
+		chip->ops->btc_bt_aci_imp(rtwdev);
+	}
+
+	level_id = (u8)dm->trx_para_level;
+
+	if (level_id >= chip->rf_para_dlink_num ||
+	    level_id >= chip->rf_para_ulink_num) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): invalid level_id: %d\n",
+			    __func__, level_id);
+		return;
+	}
+
+	if (wl->status.map.traffic_dir & BIT(RTW89_TFC_UL))
+		para = chip->rf_para_ulink[level_id];
+	else
+		para = chip->rf_para_dlink[level_id];
+
+	if (para.wl_tx_power != RTW89_BTC_WL_DEF_TX_PWR)
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): wl_tx_power=%d\n",
+			    __func__, para.wl_tx_power);
+	_set_wl_tx_power(rtwdev, para.wl_tx_power);
+	_set_wl_rx_gain(rtwdev, para.wl_rx_gain);
+	_set_bt_tx_power(rtwdev, para.bt_tx_power);
+	_set_bt_rx_gain(rtwdev, para.bt_rx_gain);
+
+	if (bt->enable.now == 0 || wl->status.map.rf_off == 1 ||
+	    wl->status.map.lps == 1)
+		wl_stb_chg = 0;
+	else
+		wl_stb_chg = 1;
+
+	if (wl_stb_chg != dm->wl_stb_chg) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): wl_stb_chg=%d\n",
+			    __func__, wl_stb_chg);
+		dm->wl_stb_chg = wl_stb_chg;
+		chip->ops->btc_wl_s1_standby(rtwdev, dm->wl_stb_chg);
+	}
+}
+
+static void _update_btc_state_map(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+	struct rtw89_btc_bt_link_info *bt_linfo = &bt->link_info;
+
+	if (wl->status.map.connecting || wl->status.map._4way ||
+	    wl->status.map.roaming) {
+		cx->state_map = BTC_WLINKING;
+	} else if (wl->status.map.scan) { /* wl scan */
+		if (bt_linfo->status.map.inq_pag)
+			cx->state_map = BTC_WSCAN_BSCAN;
+		else
+			cx->state_map = BTC_WSCAN_BNOSCAN;
+	} else if (wl->status.map.busy) { /* only busy */
+		if (bt_linfo->status.map.inq_pag)
+			cx->state_map = BTC_WBUSY_BSCAN;
+		else
+			cx->state_map = BTC_WBUSY_BNOSCAN;
+	} else { /* wl idle */
+		cx->state_map = BTC_WIDLE;
+	}
+}
+
+static void _set_bt_afh_info(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_bt_link_info *b = &bt->link_info;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	u8 en = 0, i, ch = 0, bw = 0;
+
+	if (btc->ctrl.manual || wl->status.map.scan)
+		return;
+
+	/* TODO if include module->ant.type == BTC_ANT_SHARED */
+	if (wl->status.map.rf_off || bt->whql_test ||
+	    wl_rinfo->link_mode == BTC_WLINK_NOLINK ||
+	    wl_rinfo->link_mode == BTC_WLINK_5G ||
+	    wl_rinfo->connect_cnt > BTC_TDMA_WLROLE_MAX) {
+		en = false;
+	} else if (wl_rinfo->link_mode == BTC_WLINK_2G_MCC ||
+		   wl_rinfo->link_mode == BTC_WLINK_2G_SCC) {
+		en = true;
+		/* get p2p channel */
+		for (i = 0; i < RTW89_MAX_HW_PORT_NUM; i++) {
+			if (wl_rinfo->active_role[i].role ==
+			    RTW89_WIFI_ROLE_P2P_GO ||
+			    wl_rinfo->active_role[i].role ==
+			    RTW89_WIFI_ROLE_P2P_CLIENT) {
+				ch = wl_rinfo->active_role[i].ch;
+				bw = wl_rinfo->active_role[i].bw;
+				break;
+			}
+		}
+	} else {
+		en = true;
+		/* get 2g channel  */
+		for (i = 0; i < RTW89_MAX_HW_PORT_NUM; i++) {
+			if (wl_rinfo->active_role[i].connected &&
+			    wl_rinfo->active_role[i].band == RTW89_BAND_2G) {
+				ch = wl_rinfo->active_role[i].ch;
+				bw = wl_rinfo->active_role[i].bw;
+				break;
+			}
+		}
+	}
+
+	switch (bw) {
+	case RTW89_CHANNEL_WIDTH_20:
+		bw = 20 + chip->afh_guard_ch * 2;
+		break;
+	case RTW89_CHANNEL_WIDTH_40:
+		bw = 40 + chip->afh_guard_ch * 2;
+		break;
+	case RTW89_CHANNEL_WIDTH_5:
+		bw = 5 + chip->afh_guard_ch * 2;
+		break;
+	case RTW89_CHANNEL_WIDTH_10:
+		bw = 10 + chip->afh_guard_ch * 2;
+		break;
+	default:
+		bw = 0;
+		en = false; /* turn off AFH info if BW > 40 */
+		break;
+	}
+
+	if (wl->afh_info.en == en &&
+	    wl->afh_info.ch == ch &&
+	    wl->afh_info.bw == bw &&
+	    b->profile_cnt.last == b->profile_cnt.now) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return because no change!\n",
+			    __func__);
+		return;
+	}
+
+	wl->afh_info.en = en;
+	wl->afh_info.ch = ch;
+	wl->afh_info.bw = bw;
+
+	_send_fw_cmd(rtwdev, BTFC_SET, SET_BT_WL_CH_INFO, &wl->afh_info, 3);
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): en=%d, ch=%d, bw=%d\n",
+		    __func__, en, ch, bw);
+	btc->cx.cnt_wl[BTC_WCNT_CH_UPDATE]++;
+}
+
+static bool _check_freerun(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	struct rtw89_btc_bt_link_info *bt_linfo = &bt->link_info;
+	struct rtw89_btc_bt_hid_desc *hid = &bt_linfo->hid_desc;
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) {
+		btc->dm.trx_para_level = 0;
+		return false;
+	}
+
+	/* The below is dedicated antenna case */
+	if (wl_rinfo->connect_cnt > BTC_TDMA_WLROLE_MAX) {
+		btc->dm.trx_para_level = 5;
+		return true;
+	}
+
+	if (bt_linfo->profile_cnt.now == 0) {
+		btc->dm.trx_para_level = 5;
+		return true;
+	}
+
+	if (hid->pair_cnt > BTC_TDMA_BTHID_MAX) {
+		btc->dm.trx_para_level = 5;
+		return true;
+	}
+
+	/* TODO get isolation by BT psd */
+	if (btc->mdinfo.ant.isolation >= BTC_FREERUN_ANTISO_MIN) {
+		btc->dm.trx_para_level = 5;
+		return true;
+	}
+
+	if (!wl->status.map.busy) {/* wl idle -> freerun */
+		btc->dm.trx_para_level = 5;
+		return true;
+	} else if (wl->rssi_level > 1) {/* WL rssi < 50% (-60dBm) */
+		btc->dm.trx_para_level = 0;
+		return false;
+	} else if (wl->status.map.traffic_dir & BIT(RTW89_TFC_UL)) {
+		if (wl->rssi_level == 0 && bt_linfo->rssi > 31) {
+			btc->dm.trx_para_level = 6;
+			return true;
+		} else if (wl->rssi_level == 1 && bt_linfo->rssi > 36) {
+			btc->dm.trx_para_level = 7;
+			return true;
+		}
+		btc->dm.trx_para_level = 0;
+		return false;
+	} else if (wl->status.map.traffic_dir & BIT(RTW89_TFC_DL)) {
+		if (bt_linfo->rssi > 28) {
+			btc->dm.trx_para_level = 6;
+			return true;
+		}
+	}
+
+	btc->dm.trx_para_level = 0;
+	return false;
+}
+
+#define _tdma_set_flctrl(btc, flc) ({(btc)->dm.tdma.rxflctrl = flc; })
+#define _tdma_set_tog(btc, wtg) ({(btc)->dm.tdma.wtgle_n = wtg; })
+#define _tdma_set_lek(btc, lek) ({(btc)->dm.tdma.leak_n = lek; })
+
+#define _slot_set(btc, sid, dura, tbl, type) \
+	do { \
+		typeof(sid) _sid = (sid); \
+		typeof(btc) _btc = (btc); \
+		_btc->dm.slot[_sid].dur = cpu_to_le16(dura);\
+		_btc->dm.slot[_sid].cxtbl = cpu_to_le32(tbl); \
+		_btc->dm.slot[_sid].cxtype = cpu_to_le16(type); \
+	} while (0)
+
+#define _slot_set_dur(btc, sid, dura) (btc)->dm.slot[sid].dur = cpu_to_le16(dura)
+#define _slot_set_tbl(btc, sid, tbl) (btc)->dm.slot[sid].cxtbl = cpu_to_le32(tbl)
+#define _slot_set_type(btc, sid, type) (btc)->dm.slot[sid].cxtype = cpu_to_le16(type)
+
+struct btc_btinfo_lb2 {
+	u8 connect: 1;
+	u8 sco_busy: 1;
+	u8 inq_pag: 1;
+	u8 acl_busy: 1;
+	u8 hfp: 1;
+	u8 hid: 1;
+	u8 a2dp: 1;
+	u8 pan: 1;
+};
+
+struct btc_btinfo_lb3 {
+	u8 retry: 4;
+	u8 cqddr: 1;
+	u8 inq: 1;
+	u8 mesh_busy: 1;
+	u8 pag: 1;
+};
+
+struct btc_btinfo_hb0 {
+	s8 rssi;
+};
+
+struct btc_btinfo_hb1 {
+	u8 ble_connect: 1;
+	u8 reinit: 1;
+	u8 relink: 1;
+	u8 igno_wl: 1;
+	u8 voice: 1;
+	u8 ble_scan: 1;
+	u8 role_sw: 1;
+	u8 multi_link: 1;
+};
+
+struct btc_btinfo_hb2 {
+	u8 pan_active: 1;
+	u8 afh_update: 1;
+	u8 a2dp_active: 1;
+	u8 slave: 1;
+	u8 hid_slot: 2;
+	u8 hid_cnt: 2;
+};
+
+struct btc_btinfo_hb3 {
+	u8 a2dp_bitpool: 6;
+	u8 tx_3m: 1;
+	u8 a2dp_sink: 1;
+};
+
+union btc_btinfo {
+	u8 val;
+	struct btc_btinfo_lb2 lb2;
+	struct btc_btinfo_lb3 lb3;
+	struct btc_btinfo_hb0 hb0;
+	struct btc_btinfo_hb1 hb1;
+	struct btc_btinfo_hb2 hb2;
+	struct btc_btinfo_hb3 hb3;
+};
+
+static void _set_policy(struct rtw89_dev *rtwdev, u16 policy_type,
+			enum btc_reason_and_action action)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_fbtc_tdma *t = &dm->tdma;
+	struct rtw89_btc_fbtc_slot *s = dm->slot;
+	u8 type;
+	u32 tbl_w1, tbl_b1, tbl_b4;
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) {
+		if (btc->cx.wl.status.map._4way)
+			tbl_w1 = cxtbl[1];
+		else
+			tbl_w1 = cxtbl[8];
+		tbl_b1 = cxtbl[3];
+		tbl_b4 = cxtbl[3];
+	} else {
+		tbl_w1 = cxtbl[16];
+		tbl_b1 = cxtbl[17];
+		tbl_b4 = cxtbl[17];
+	}
+
+	type = (u8)((policy_type & BTC_CXP_MASK) >> 8);
+	btc->bt_req_en = false;
+
+	switch (type) {
+	case BTC_CXP_USERDEF0:
+		*t = t_def[CXTD_OFF];
+		s[CXST_OFF] = s_def[CXST_OFF];
+		_slot_set_tbl(btc, CXST_OFF, cxtbl[2]);
+		btc->update_policy_force = true;
+		break;
+	case BTC_CXP_OFF: /* TDMA off */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, false);
+		*t = t_def[CXTD_OFF];
+		s[CXST_OFF] = s_def[CXST_OFF];
+
+		switch (policy_type) {
+		case BTC_CXP_OFF_BT:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[2]);
+			break;
+		case BTC_CXP_OFF_WL:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[1]);
+			break;
+		case BTC_CXP_OFF_EQ0:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[0]);
+			break;
+		case BTC_CXP_OFF_EQ1:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[16]);
+			break;
+		case BTC_CXP_OFF_EQ2:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[17]);
+			break;
+		case BTC_CXP_OFF_EQ3:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[18]);
+			break;
+		case BTC_CXP_OFF_BWB0:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[5]);
+			break;
+		case BTC_CXP_OFF_BWB1:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[8]);
+			break;
+		}
+		break;
+	case BTC_CXP_OFFB: /* TDMA off + beacon protect */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, false);
+		*t = t_def[CXTD_OFF_B2];
+		s[CXST_OFF] = s_def[CXST_OFF];
+		switch (policy_type) {
+		case BTC_CXP_OFFB_BWB0:
+			_slot_set_tbl(btc, CXST_OFF, cxtbl[8]);
+			break;
+		}
+		break;
+	case BTC_CXP_OFFE: /* TDMA off + beacon protect + Ext_control */
+		btc->bt_req_en = true;
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_OFF_EXT];
+		switch (policy_type) {
+		case BTC_CXP_OFFE_DEF:
+			s[CXST_E2G] = s_def[CXST_E2G];
+			s[CXST_E5G] = s_def[CXST_E5G];
+			s[CXST_EBT] = s_def[CXST_EBT];
+			s[CXST_ENULL] = s_def[CXST_ENULL];
+			break;
+		case BTC_CXP_OFFE_DEF2:
+			_slot_set(btc, CXST_E2G, 20, cxtbl[1], SLOT_ISO);
+			s[CXST_E5G] = s_def[CXST_E5G];
+			s[CXST_EBT] = s_def[CXST_EBT];
+			s[CXST_ENULL] = s_def[CXST_ENULL];
+			break;
+		}
+		break;
+	case BTC_CXP_FIX: /* TDMA Fix-Slot */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_FIX];
+		switch (policy_type) {
+		case BTC_CXP_FIX_TD3030:
+			_slot_set(btc, CXST_W1, 30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 30, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD5050:
+			_slot_set(btc, CXST_W1, 50, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 50, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD2030:
+			_slot_set(btc, CXST_W1, 20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 30, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD4010:
+			_slot_set(btc, CXST_W1, 40, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 10, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD4020:
+			_slot_set(btc, CXST_W1, 40, cxtbl[1], SLOT_MIX);
+			_slot_set(btc, CXST_B1, 20, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD7010:
+			_slot_set(btc, CXST_W1, 70, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 10, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD2060:
+			_slot_set(btc, CXST_W1, 20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 60, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD3060:
+			_slot_set(btc, CXST_W1, 30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 60, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TD2080:
+			_slot_set(btc, CXST_W1, 20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 80, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_FIX_TDW1B1: /* W1:B1 = user-define */
+			_slot_set(btc, CXST_W1, dm->slot_dur[CXST_W1],
+				  tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, dm->slot_dur[CXST_B1],
+				  tbl_b1, SLOT_MIX);
+			break;
+		}
+		break;
+	case BTC_CXP_PFIX: /* PS-TDMA Fix-Slot */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_PFIX];
+		if (btc->cx.wl.role_info.role_map.role.ap)
+			_tdma_set_flctrl(btc, CXFLC_QOSNULL);
+
+		switch (policy_type) {
+		case BTC_CXP_PFIX_TD3030:
+			_slot_set(btc, CXST_W1, 30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 30, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PFIX_TD5050:
+			_slot_set(btc, CXST_W1, 50, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 50, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PFIX_TD2030:
+			_slot_set(btc, CXST_W1, 20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 30, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PFIX_TD2060:
+			_slot_set(btc, CXST_W1, 20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 60, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PFIX_TD3070:
+			_slot_set(btc, CXST_W1, 30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 60, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PFIX_TD2080:
+			_slot_set(btc, CXST_W1, 20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 80, tbl_b1, SLOT_MIX);
+			break;
+		}
+		break;
+	case BTC_CXP_AUTO: /* TDMA Auto-Slot */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_AUTO];
+		switch (policy_type) {
+		case BTC_CXP_AUTO_TD50200:
+			_slot_set(btc, CXST_W1,  50, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO_TD60200:
+			_slot_set(btc, CXST_W1,  60, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO_TD20200:
+			_slot_set(btc, CXST_W1,  20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO_TDW1B1: /* W1:B1 = user-define */
+			_slot_set(btc, CXST_W1, dm->slot_dur[CXST_W1],
+				  tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, dm->slot_dur[CXST_B1],
+				  tbl_b1, SLOT_MIX);
+			break;
+		}
+		break;
+	case BTC_CXP_PAUTO: /* PS-TDMA Auto-Slot */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_PAUTO];
+		switch (policy_type) {
+		case BTC_CXP_PAUTO_TD50200:
+			_slot_set(btc, CXST_W1,  50, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO_TD60200:
+			_slot_set(btc, CXST_W1,  60, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO_TD20200:
+			_slot_set(btc, CXST_W1,  20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO_TDW1B1:
+			_slot_set(btc, CXST_W1, dm->slot_dur[CXST_W1],
+				  tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, dm->slot_dur[CXST_B1],
+				  tbl_b1, SLOT_MIX);
+			break;
+		}
+		break;
+	case BTC_CXP_AUTO2: /* TDMA Auto-Slot2 */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_AUTO2];
+		switch (policy_type) {
+		case BTC_CXP_AUTO2_TD3050:
+			_slot_set(btc, CXST_W1,  30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  50, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO2_TD3070:
+			_slot_set(btc, CXST_W1,  30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  70, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO2_TD5050:
+			_slot_set(btc, CXST_W1,  50, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  50, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO2_TD6060:
+			_slot_set(btc, CXST_W1,  60, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  60, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO2_TD2080:
+			_slot_set(btc, CXST_W1,  20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  80, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_AUTO2_TDW1B4: /* W1:B1 = user-define */
+			_slot_set(btc, CXST_W1, dm->slot_dur[CXST_W1],
+				  tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B4, dm->slot_dur[CXST_B4],
+				  tbl_b4, SLOT_MIX);
+			break;
+		}
+		break;
+	case BTC_CXP_PAUTO2: /* PS-TDMA Auto-Slot2 */
+		_write_scbd(rtwdev, BTC_WSCB_TDMA, true);
+		*t = t_def[CXTD_PAUTO2];
+		switch (policy_type) {
+		case BTC_CXP_PAUTO2_TD3050:
+			_slot_set(btc, CXST_W1,  30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  50, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO2_TD3070:
+			_slot_set(btc, CXST_W1,  30, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  70, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO2_TD5050:
+			_slot_set(btc, CXST_W1,  50, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  50, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO2_TD6060:
+			_slot_set(btc, CXST_W1,  60, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  60, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO2_TD2080:
+			_slot_set(btc, CXST_W1,  20, tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B1, 200, tbl_b1, SLOT_MIX);
+			_slot_set(btc, CXST_B4,  80, tbl_b4, SLOT_MIX);
+			break;
+		case BTC_CXP_PAUTO2_TDW1B4: /* W1:B1 = user-define */
+			_slot_set(btc, CXST_W1, dm->slot_dur[CXST_W1],
+				  tbl_w1, SLOT_ISO);
+			_slot_set(btc, CXST_B4, dm->slot_dur[CXST_B4],
+				  tbl_b4, SLOT_MIX);
+			break;
+		}
+		break;
+	}
+
+	_fw_set_policy(rtwdev, policy_type, action);
+}
+
+static void _set_gnt_bt(struct rtw89_dev *rtwdev, u8 phy_map, u8 state)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_mac_ax_gnt *g = dm->gnt.band;
+	u8 i;
+
+	if (phy_map > BTC_PHY_ALL)
+		return;
+
+	for (i = 0; i < RTW89_PHY_MAX; i++) {
+		if (!(phy_map & BIT(i)))
+			continue;
+
+		switch (state) {
+		case BTC_GNT_HW:
+			g[i].gnt_bt_sw_en = 0;
+			g[i].gnt_bt = 0;
+			break;
+		case BTC_GNT_SW_LO:
+			g[i].gnt_bt_sw_en = 1;
+			g[i].gnt_bt = 0;
+			break;
+		case BTC_GNT_SW_HI:
+			g[i].gnt_bt_sw_en = 1;
+			g[i].gnt_bt = 1;
+			break;
+		}
+	}
+
+	rtw89_mac_cfg_gnt(rtwdev, &dm->gnt);
+}
+
+static void _set_bt_plut(struct rtw89_dev *rtwdev, u8 phy_map,
+			 u8 tx_val, u8 rx_val)
+{
+	struct rtw89_mac_ax_plt plt;
+
+	plt.band = RTW89_MAC_0;
+	plt.tx = tx_val;
+	plt.rx = rx_val;
+
+	if (phy_map & BTC_PHY_0)
+		rtw89_mac_cfg_plt(rtwdev, &plt);
+
+	if (!rtwdev->dbcc_en)
+		return;
+
+	plt.band = RTW89_MAC_1;
+	if (phy_map & BTC_PHY_1)
+		rtw89_mac_cfg_plt(rtwdev, &plt);
+}
+
+static void _set_ant(struct rtw89_dev *rtwdev, bool force_exec,
+		     u8 phy_map, u8 type)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+	struct rtw89_btc_wl_dbcc_info *wl_dinfo = &wl->dbcc_info;
+	u8 gnt_wl_ctrl, gnt_bt_ctrl, plt_ctrl, i, b2g = 0;
+	u32 ant_path_type;
+
+	ant_path_type = ((phy_map << 8) + type);
+
+	if (btc->dm.run_reason == BTC_RSN_NTFY_POWEROFF ||
+	    btc->dm.run_reason == BTC_RSN_NTFY_RADIO_STATE ||
+	    btc->dm.run_reason == BTC_RSN_CMD_SET_COEX)
+		force_exec = FC_EXEC;
+
+	if (!force_exec && ant_path_type == dm->set_ant_path) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return by no change!!\n",
+			     __func__);
+		return;
+	} else if (bt->rfk_info.map.run) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return by bt rfk!!\n", __func__);
+		return;
+	} else if (btc->dm.run_reason != BTC_RSN_NTFY_WL_RFK &&
+		   wl->rfk_info.state != BTC_WRFK_STOP) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return by wl rfk!!\n", __func__);
+		return;
+	}
+
+	dm->set_ant_path = ant_path_type;
+
+	rtw89_debug(rtwdev,
+		    RTW89_DBG_BTC,
+		    "[BTC], %s(): path=0x%x, set_type=0x%x\n",
+		    __func__, phy_map, dm->set_ant_path & 0xff);
+
+	switch (type) {
+	case BTC_ANT_WPOWERON:
+		rtw89_mac_cfg_ctrl_path(rtwdev, false);
+		break;
+	case BTC_ANT_WINIT:
+		if (bt->enable.now) {
+			_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_LO);
+			_set_gnt_bt(rtwdev, phy_map, BTC_GNT_SW_HI);
+		} else {
+			_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_HI);
+			_set_gnt_bt(rtwdev, phy_map, BTC_GNT_SW_LO);
+		}
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		_set_bt_plut(rtwdev, BTC_PHY_ALL, BTC_PLT_BT, BTC_PLT_BT);
+		break;
+	case BTC_ANT_WONLY:
+		_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_HI);
+		_set_gnt_bt(rtwdev, phy_map, BTC_GNT_SW_LO);
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		_set_bt_plut(rtwdev, BTC_PHY_ALL, BTC_PLT_NONE, BTC_PLT_NONE);
+		break;
+	case BTC_ANT_WOFF:
+		rtw89_mac_cfg_ctrl_path(rtwdev, false);
+		_set_bt_plut(rtwdev, BTC_PHY_ALL, BTC_PLT_NONE, BTC_PLT_NONE);
+		break;
+	case BTC_ANT_W2G:
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		if (rtwdev->dbcc_en) {
+			for (i = 0; i < RTW89_PHY_MAX; i++) {
+				b2g = (wl_dinfo->real_band[i] == RTW89_BAND_2G);
+
+				gnt_wl_ctrl = b2g ? BTC_GNT_HW : BTC_GNT_SW_HI;
+				_set_gnt_wl(rtwdev, BIT(i), gnt_wl_ctrl);
+
+				gnt_bt_ctrl = b2g ? BTC_GNT_HW : BTC_GNT_SW_HI;
+				/* BT should control by GNT_BT if WL_2G at S0 */
+				if (i == 1 &&
+				    wl_dinfo->real_band[0] == RTW89_BAND_2G &&
+				    wl_dinfo->real_band[1] == RTW89_BAND_5G)
+					gnt_bt_ctrl = BTC_GNT_HW;
+				_set_gnt_bt(rtwdev, BIT(i), gnt_bt_ctrl);
+
+				plt_ctrl = b2g ? BTC_PLT_BT : BTC_PLT_NONE;
+				_set_bt_plut(rtwdev, BIT(i),
+					     plt_ctrl, plt_ctrl);
+			}
+		} else {
+			_set_gnt_wl(rtwdev, phy_map, BTC_GNT_HW);
+			_set_gnt_bt(rtwdev, phy_map, BTC_GNT_HW);
+			_set_bt_plut(rtwdev, BTC_PHY_ALL,
+				     BTC_PLT_BT, BTC_PLT_BT);
+		}
+		break;
+	case BTC_ANT_W5G:
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_HI);
+		_set_gnt_bt(rtwdev, phy_map, BTC_GNT_HW);
+		_set_bt_plut(rtwdev, BTC_PHY_ALL, BTC_PLT_NONE, BTC_PLT_NONE);
+		break;
+	case BTC_ANT_W25G:
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		_set_gnt_wl(rtwdev, phy_map, BTC_GNT_HW);
+		_set_gnt_bt(rtwdev, phy_map, BTC_GNT_HW);
+		_set_bt_plut(rtwdev, BTC_PHY_ALL,
+			     BTC_PLT_GNT_WL, BTC_PLT_GNT_WL);
+		break;
+	case BTC_ANT_FREERUN:
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_HI);
+		_set_gnt_bt(rtwdev, phy_map, BTC_GNT_SW_HI);
+		_set_bt_plut(rtwdev, BTC_PHY_ALL, BTC_PLT_NONE, BTC_PLT_NONE);
+		break;
+	case BTC_ANT_WRFK:
+		rtw89_mac_cfg_ctrl_path(rtwdev, true);
+		_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_HI);
+		_set_gnt_bt(rtwdev, phy_map, BTC_GNT_SW_LO);
+		_set_bt_plut(rtwdev, phy_map, BTC_PLT_NONE, BTC_PLT_NONE);
+		break;
+	case BTC_ANT_BRFK:
+		rtw89_mac_cfg_ctrl_path(rtwdev, false);
+		_set_gnt_wl(rtwdev, phy_map, BTC_GNT_SW_LO);
+		_set_gnt_bt(rtwdev, phy_map, BTC_GNT_SW_HI);
+		_set_bt_plut(rtwdev, phy_map, BTC_PLT_NONE, BTC_PLT_NONE);
+		break;
+	default:
+		break;
+	}
+}
+
+static void _action_wl_only(struct rtw89_dev *rtwdev)
+{
+	_set_ant(rtwdev, FC_EXEC, BTC_PHY_ALL, BTC_ANT_WONLY);
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_WL_ONLY);
+}
+
+static void _action_wl_init(struct rtw89_dev *rtwdev)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+
+	_set_ant(rtwdev, FC_EXEC, BTC_PHY_ALL, BTC_ANT_WINIT);
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_WL_INIT);
+}
+
+static void _action_wl_off(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+
+	if (wl->status.map.rf_off || btc->dm.bt_only)
+		_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_WOFF);
+
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_WL_OFF);
+}
+
+static void _action_freerun(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+
+	_set_ant(rtwdev, FC_EXEC, BTC_PHY_ALL, BTC_ANT_FREERUN);
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_FREERUN);
+
+	btc->dm.freerun = true;
+}
+
+static void _action_bt_whql(struct rtw89_dev *rtwdev)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+
+	_set_ant(rtwdev, FC_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_BT_WHQL);
+}
+
+static void _action_bt_off(struct rtw89_dev *rtwdev)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+
+	_set_ant(rtwdev, FC_EXEC, BTC_PHY_ALL, BTC_ANT_WONLY);
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_BT_OFF);
+}
+
+static void _action_bt_idle(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_link_info *b = &btc->cx.bt.link_info;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) { /* shared-antenna */
+		switch (btc->cx.state_map) {
+		case BTC_WBUSY_BNOSCAN: /*wl-busy + bt idle*/
+			if (b->profile_cnt.now > 0)
+				_set_policy(rtwdev, BTC_CXP_FIX_TD4010,
+					    BTC_ACT_BT_IDLE);
+			else
+				_set_policy(rtwdev, BTC_CXP_FIX_TD4020,
+					    BTC_ACT_BT_IDLE);
+			break;
+		case BTC_WBUSY_BSCAN: /*wl-busy + bt-inq */
+			_set_policy(rtwdev, BTC_CXP_PFIX_TD5050,
+				    BTC_ACT_BT_IDLE);
+			break;
+		case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-idle */
+			if (b->profile_cnt.now > 0)
+				_set_policy(rtwdev, BTC_CXP_FIX_TD4010,
+					    BTC_ACT_BT_IDLE);
+			else
+				_set_policy(rtwdev, BTC_CXP_FIX_TD4020,
+					    BTC_ACT_BT_IDLE);
+			break;
+		case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq */
+			_set_policy(rtwdev, BTC_CXP_FIX_TD5050,
+				    BTC_ACT_BT_IDLE);
+			break;
+		case BTC_WLINKING: /* wl-connecting + bt-inq or bt-idle */
+			_set_policy(rtwdev, BTC_CXP_FIX_TD7010,
+				    BTC_ACT_BT_IDLE);
+			break;
+		case BTC_WIDLE:  /* wl-idle + bt-idle */
+			_set_policy(rtwdev, BTC_CXP_OFF_BWB1, BTC_ACT_BT_IDLE);
+			break;
+		}
+	} else { /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_BT_IDLE);
+	}
+}
+
+static void _action_bt_hfp(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) {
+		if (btc->cx.wl.status.map._4way)
+			_set_policy(rtwdev, BTC_CXP_OFF_WL, BTC_ACT_BT_HFP);
+		else
+			_set_policy(rtwdev, BTC_CXP_OFF_BWB0, BTC_ACT_BT_HFP);
+	} else {
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ2, BTC_ACT_BT_HFP);
+	}
+}
+
+static void _action_bt_hid(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) /* shared-antenna */
+		if (btc->cx.wl.status.map._4way)
+			_set_policy(rtwdev, BTC_CXP_OFF_WL, BTC_ACT_BT_HID);
+		else
+			_set_policy(rtwdev, BTC_CXP_OFF_BWB0, BTC_ACT_BT_HID);
+	else /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ3, BTC_ACT_BT_HID);
+}
+
+static void _action_bt_a2dp(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_link_info *bt_linfo = &btc->cx.bt.link_info;
+	struct rtw89_btc_bt_a2dp_desc a2dp = bt_linfo->a2dp_desc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-A2DP */
+		if (a2dp.vendor_id == 0x4c || dm->leak_ap) {
+			dm->slot_dur[CXST_W1] = 40;
+			dm->slot_dur[CXST_B1] = 200;
+			_set_policy(rtwdev,
+				    BTC_CXP_PAUTO_TDW1B1, BTC_ACT_BT_A2DP);
+		} else {
+			_set_policy(rtwdev,
+				    BTC_CXP_PAUTO_TD50200, BTC_ACT_BT_A2DP);
+		}
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-A2DP */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD3050, BTC_ACT_BT_A2DP);
+		break;
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-A2DP */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD3050, BTC_ACT_BT_A2DP);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-A2DP */
+	case BTC_WLINKING: /* wl-connecting + bt-A2DP */
+		if (a2dp.vendor_id == 0x4c || dm->leak_ap) {
+			dm->slot_dur[CXST_W1] = 40;
+			dm->slot_dur[CXST_B1] = 200;
+			_set_policy(rtwdev, BTC_CXP_AUTO_TDW1B1,
+				    BTC_ACT_BT_A2DP);
+		} else {
+			_set_policy(rtwdev, BTC_CXP_AUTO_TD50200,
+				    BTC_ACT_BT_A2DP);
+		}
+		break;
+	case BTC_WIDLE:  /* wl-idle + bt-A2DP */
+		_set_policy(rtwdev, BTC_CXP_AUTO_TD20200, BTC_ACT_BT_A2DP);
+		break;
+	}
+}
+
+static void _action_bt_a2dpsink(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-A2dp_Sink */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD2030, BTC_ACT_BT_A2DPSINK);
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-A2dp_Sink */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD2060, BTC_ACT_BT_A2DPSINK);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-A2dp_Sink */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD2030, BTC_ACT_BT_A2DPSINK);
+		break;
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-A2dp_Sink */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD2060, BTC_ACT_BT_A2DPSINK);
+		break;
+	case BTC_WLINKING: /* wl-connecting + bt-A2dp_Sink */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD3030, BTC_ACT_BT_A2DPSINK);
+		break;
+	case BTC_WIDLE: /* wl-idle + bt-A2dp_Sink */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD2080, BTC_ACT_BT_A2DPSINK);
+		break;
+	}
+}
+
+static void _action_bt_pan(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-PAN */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD5050, BTC_ACT_BT_PAN);
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-PAN */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD3070, BTC_ACT_BT_PAN);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-PAN */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD3030, BTC_ACT_BT_PAN);
+		break;
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-PAN */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD3060, BTC_ACT_BT_PAN);
+		break;
+	case BTC_WLINKING: /* wl-connecting + bt-PAN */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD4020, BTC_ACT_BT_PAN);
+		break;
+	case BTC_WIDLE: /* wl-idle + bt-pan */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD2080, BTC_ACT_BT_PAN);
+		break;
+	}
+}
+
+static void _action_bt_a2dp_hid(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_link_info *bt_linfo = &btc->cx.bt.link_info;
+	struct rtw89_btc_bt_a2dp_desc a2dp = bt_linfo->a2dp_desc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-A2DP+HID */
+	case BTC_WIDLE:  /* wl-idle + bt-A2DP */
+		if (a2dp.vendor_id == 0x4c || dm->leak_ap) {
+			dm->slot_dur[CXST_W1] = 40;
+			dm->slot_dur[CXST_B1] = 200;
+			_set_policy(rtwdev,
+				    BTC_CXP_PAUTO_TDW1B1, BTC_ACT_BT_A2DP_HID);
+		} else {
+			_set_policy(rtwdev,
+				    BTC_CXP_PAUTO_TD50200, BTC_ACT_BT_A2DP_HID);
+		}
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-A2DP+HID */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD3050, BTC_ACT_BT_A2DP_HID);
+		break;
+
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-A2DP+HID */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD3050, BTC_ACT_BT_A2DP_HID);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-A2DP+HID */
+	case BTC_WLINKING: /* wl-connecting + bt-A2DP+HID */
+		if (a2dp.vendor_id == 0x4c || dm->leak_ap) {
+			dm->slot_dur[CXST_W1] = 40;
+			dm->slot_dur[CXST_B1] = 200;
+			_set_policy(rtwdev, BTC_CXP_AUTO_TDW1B1,
+				    BTC_ACT_BT_A2DP_HID);
+		} else {
+			_set_policy(rtwdev, BTC_CXP_AUTO_TD50200,
+				    BTC_ACT_BT_A2DP_HID);
+		}
+		break;
+	}
+}
+
+static void _action_bt_a2dp_pan(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-A2DP+PAN */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD3070, BTC_ACT_BT_A2DP_PAN);
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-A2DP+PAN */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD3070, BTC_ACT_BT_A2DP_PAN);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-A2DP+PAN */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD5050, BTC_ACT_BT_A2DP_PAN);
+		break;
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-A2DP+PAN */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD3070, BTC_ACT_BT_A2DP_PAN);
+		break;
+	case BTC_WLINKING: /* wl-connecting + bt-A2DP+PAN */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD3050, BTC_ACT_BT_A2DP_PAN);
+		break;
+	case BTC_WIDLE:  /* wl-idle + bt-A2DP+PAN */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD2080, BTC_ACT_BT_A2DP_PAN);
+		break;
+	}
+}
+
+static void _action_bt_pan_hid(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD3030, BTC_ACT_BT_PAN_HID);
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD3070, BTC_ACT_BT_PAN_HID);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD3030, BTC_ACT_BT_PAN_HID);
+		break;
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD3060, BTC_ACT_BT_PAN_HID);
+		break;
+	case BTC_WLINKING: /* wl-connecting + bt-PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_FIX_TD4010, BTC_ACT_BT_PAN_HID);
+		break;
+	case BTC_WIDLE: /* wl-idle + bt-PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_PFIX_TD2080, BTC_ACT_BT_PAN_HID);
+		break;
+	}
+}
+
+static void _action_bt_a2dp_pan_hid(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	switch (btc->cx.state_map) {
+	case BTC_WBUSY_BNOSCAN: /* wl-busy + bt-A2DP+PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD3070,
+			    BTC_ACT_BT_A2DP_PAN_HID);
+		break;
+	case BTC_WBUSY_BSCAN: /* wl-busy + bt-inq + bt-A2DP+PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD3070,
+			    BTC_ACT_BT_A2DP_PAN_HID);
+		break;
+	case BTC_WSCAN_BSCAN: /* wl-scan + bt-inq + bt-A2DP+PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD3070,
+			    BTC_ACT_BT_A2DP_PAN_HID);
+		break;
+	case BTC_WSCAN_BNOSCAN: /* wl-scan + bt-A2DP+PAN+HID */
+	case BTC_WLINKING: /* wl-connecting + bt-A2DP+PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_AUTO2_TD3050,
+			    BTC_ACT_BT_A2DP_PAN_HID);
+		break;
+	case BTC_WIDLE:  /* wl-idle + bt-A2DP+PAN+HID */
+		_set_policy(rtwdev, BTC_CXP_PAUTO2_TD2080,
+			    BTC_ACT_BT_A2DP_PAN_HID);
+		break;
+	}
+}
+
+static void _action_wl_5g(struct rtw89_dev *rtwdev)
+{
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W5G);
+	_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_5G);
+}
+
+static void _action_wl_other(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED)
+		_set_policy(rtwdev, BTC_CXP_OFFB_BWB0, BTC_ACT_WL_OTHER);
+	else
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_OTHER);
+}
+
+static void _action_wl_nc(struct rtw89_dev *rtwdev)
+{
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+	_set_policy(rtwdev, BTC_CXP_OFF_BT, BTC_ACT_WL_NC);
+}
+
+static void _action_wl_rfk(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_rfk_info rfk = btc->cx.wl.rfk_info;
+
+	if (rfk.state != BTC_WRFK_START)
+		return;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): band = %d\n",
+		    __func__, rfk.band);
+
+	_set_ant(rtwdev, FC_EXEC, BTC_PHY_ALL, BTC_ANT_WRFK);
+	_set_policy(rtwdev, BTC_CXP_OFF_WL, BTC_ACT_WL_RFK);
+}
+
+static void _set_btg_ctrl(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	struct rtw89_btc_wl_dbcc_info *wl_dinfo = &wl->dbcc_info;
+	bool is_btg = false;
+
+	if (btc->ctrl.manual)
+		return;
+
+	/* notify halbb ignore GNT_BT or not for WL BB Rx-AGC control */
+	if (wl_rinfo->link_mode == BTC_WLINK_5G) /* always 0 if 5G */
+		is_btg = false;
+	else if (wl_rinfo->link_mode == BTC_WLINK_25G_DBCC &&
+		 wl_dinfo->real_band[RTW89_PHY_1] != RTW89_BAND_2G)
+		is_btg = false;
+	else
+		is_btg = true;
+
+	if (btc->dm.run_reason != BTC_RSN_NTFY_INIT &&
+	    is_btg == btc->dm.wl_btg_rx)
+		return;
+
+	btc->dm.wl_btg_rx = is_btg;
+
+	if (wl_rinfo->link_mode == BTC_WLINK_25G_MCC)
+		return;
+
+	rtw89_ctrl_btg(rtwdev, is_btg);
+}
+
+struct rtw89_txtime_data {
+	struct rtw89_dev *rtwdev;
+	int type;
+	u32 tx_time;
+	u8 tx_retry;
+	u16 enable;
+	bool reenable;
+};
+
+static void rtw89_tx_time_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_txtime_data *iter_data =
+				(struct rtw89_txtime_data *)data;
+	struct rtw89_dev *rtwdev = iter_data->rtwdev;
+	struct rtw89_vif *rtwvif = rtwsta->rtwvif;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_wl_link_info *plink = NULL;
+	u8 port = rtwvif->port;
+	u32 tx_time = iter_data->tx_time;
+	u8 tx_retry = iter_data->tx_retry;
+	u16 enable = iter_data->enable;
+	bool reenable = iter_data->reenable;
+
+	plink = &wl->link_info[port];
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): port = %d\n", __func__, port);
+
+	if (!plink->connected) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): connected = %d\n",
+			    __func__, plink->connected);
+		return;
+	}
+
+	/* backup the original tx time before tx-limit on */
+	if (reenable) {
+		rtw89_mac_get_tx_time(rtwdev, rtwsta, &plink->tx_time);
+		rtw89_mac_get_tx_retry_limit(rtwdev, rtwsta, &plink->tx_retry);
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): reenable, tx_time=%d tx_retry= %d\n",
+			    __func__, plink->tx_time, plink->tx_retry);
+	}
+
+	/* restore the original tx time if no tx-limit */
+	if (!enable) {
+		rtw89_mac_set_tx_time(rtwdev, rtwsta, true, plink->tx_time);
+		rtw89_mac_set_tx_retry_limit(rtwdev, rtwsta, true,
+					     plink->tx_retry);
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): restore, tx_time=%d tx_retry= %d\n",
+			    __func__, plink->tx_time, plink->tx_retry);
+
+	} else {
+		rtw89_mac_set_tx_time(rtwdev, rtwsta, false, tx_time);
+		rtw89_mac_set_tx_retry_limit(rtwdev, rtwsta, false, tx_retry);
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): set, tx_time=%d tx_retry= %d\n",
+			    __func__, tx_time, tx_retry);
+	}
+}
+
+static void _set_wl_tx_limit(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+	struct rtw89_btc_bt_link_info *b = &bt->link_info;
+	struct rtw89_btc_bt_hfp_desc *hfp = &b->hfp_desc;
+	struct rtw89_btc_bt_hid_desc *hid = &b->hid_desc;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	struct rtw89_txtime_data data = {.rtwdev = rtwdev};
+	u8 mode = wl_rinfo->link_mode;
+	u8 tx_retry = 0;
+	u32 tx_time = 0;
+	u16 enable = 0;
+	bool reenable = false;
+
+	if (btc->ctrl.manual)
+		return;
+
+	if (btc->dm.freerun || btc->ctrl.igno_bt || b->profile_cnt.now == 0 ||
+	    mode == BTC_WLINK_5G || mode == BTC_WLINK_NOLINK) {
+		enable = 0;
+		tx_time = BTC_MAX_TX_TIME_DEF;
+		tx_retry = BTC_MAX_TX_RETRY_DEF;
+	} else if ((hfp->exist && hid->exist) || hid->pair_cnt > 1) {
+		enable = 1;
+		tx_time = BTC_MAX_TX_TIME_L2;
+		tx_retry = BTC_MAX_TX_RETRY_L1;
+	} else if (hfp->exist || hid->exist) {
+		enable = 1;
+		tx_time = BTC_MAX_TX_TIME_L3;
+		tx_retry = BTC_MAX_TX_RETRY_L1;
+	} else {
+		enable = 0;
+		tx_time = BTC_MAX_TX_TIME_DEF;
+		tx_retry = BTC_MAX_TX_RETRY_DEF;
+	}
+
+	if (dm->wl_tx_limit.enable == enable &&
+	    dm->wl_tx_limit.tx_time == tx_time &&
+	    dm->wl_tx_limit.tx_retry == tx_retry)
+		return;
+
+	if (!dm->wl_tx_limit.enable && enable)
+		reenable = true;
+
+	dm->wl_tx_limit.enable = enable;
+	dm->wl_tx_limit.tx_time = tx_time;
+	dm->wl_tx_limit.tx_retry = tx_retry;
+
+	data.enable = enable;
+	data.tx_time = tx_time;
+	data.tx_retry = tx_retry;
+	data.reenable = reenable;
+
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_tx_time_iter,
+					  &data);
+}
+
+static void _set_bt_rx_agc(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	bool bt_hi_lna_rx = false;
+
+	if (wl_rinfo->link_mode != BTC_WLINK_NOLINK && btc->dm.wl_btg_rx)
+		bt_hi_lna_rx = true;
+
+	if (bt_hi_lna_rx == bt->hi_lna_rx)
+		return;
+
+	_write_scbd(rtwdev, BTC_WSCB_BT_HILNA, bt_hi_lna_rx);
+}
+
+/* TODO add these functions */
+static void _action_common(struct rtw89_dev *rtwdev)
+{
+	_set_btg_ctrl(rtwdev);
+	_set_wl_tx_limit(rtwdev);
+	_set_bt_afh_info(rtwdev);
+	_set_bt_rx_agc(rtwdev);
+	_set_rf_trx_para(rtwdev);
+}
+
+static void _action_by_bt(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_bt_link_info *bt_linfo = &bt->link_info;
+	struct rtw89_btc_bt_hid_desc hid = bt_linfo->hid_desc;
+	struct rtw89_btc_bt_a2dp_desc a2dp = bt_linfo->a2dp_desc;
+	struct rtw89_btc_bt_pan_desc pan = bt_linfo->pan_desc;
+	u8 profile_map = 0;
+
+	if (bt_linfo->hfp_desc.exist)
+		profile_map |= BTC_BT_HFP;
+
+	if (bt_linfo->hid_desc.exist)
+		profile_map |= BTC_BT_HID;
+
+	if (bt_linfo->a2dp_desc.exist)
+		profile_map |= BTC_BT_A2DP;
+
+	if (bt_linfo->pan_desc.exist)
+		profile_map |= BTC_BT_PAN;
+
+	switch (profile_map) {
+	case BTC_BT_NOPROFILE:
+		if (_check_freerun(rtwdev))
+			_action_freerun(rtwdev);
+		else if (a2dp.active || pan.active)
+			_action_bt_pan(rtwdev);
+		else
+			_action_bt_idle(rtwdev);
+		break;
+	case BTC_BT_HFP:
+		if (_check_freerun(rtwdev))
+			_action_freerun(rtwdev);
+		else
+			_action_bt_hfp(rtwdev);
+		break;
+	case BTC_BT_HFP | BTC_BT_HID:
+	case BTC_BT_HID:
+		if (_check_freerun(rtwdev))
+			_action_freerun(rtwdev);
+		else
+			_action_bt_hid(rtwdev);
+		break;
+	case BTC_BT_A2DP:
+		if (_check_freerun(rtwdev))
+			_action_freerun(rtwdev);
+		else if (a2dp.sink)
+			_action_bt_a2dpsink(rtwdev);
+		else if (bt_linfo->multi_link.now && !hid.pair_cnt)
+			_action_bt_a2dp_pan(rtwdev);
+		else
+			_action_bt_a2dp(rtwdev);
+		break;
+	case BTC_BT_PAN:
+		_action_bt_pan(rtwdev);
+		break;
+	case BTC_BT_A2DP | BTC_BT_HFP:
+	case BTC_BT_A2DP | BTC_BT_HID:
+	case BTC_BT_A2DP | BTC_BT_HFP | BTC_BT_HID:
+		if (_check_freerun(rtwdev))
+			_action_freerun(rtwdev);
+		else
+			_action_bt_a2dp_hid(rtwdev);
+		break;
+	case BTC_BT_A2DP | BTC_BT_PAN:
+		_action_bt_a2dp_pan(rtwdev);
+		break;
+	case BTC_BT_PAN | BTC_BT_HFP:
+	case BTC_BT_PAN | BTC_BT_HID:
+	case BTC_BT_PAN | BTC_BT_HFP | BTC_BT_HID:
+		_action_bt_pan_hid(rtwdev);
+		break;
+	case BTC_BT_A2DP | BTC_BT_PAN | BTC_BT_HID:
+	case BTC_BT_A2DP | BTC_BT_PAN | BTC_BT_HFP:
+	default:
+		_action_bt_a2dp_pan_hid(rtwdev);
+		break;
+	}
+}
+
+static void _action_wl_2g_sta(struct rtw89_dev *rtwdev)
+{
+	_action_by_bt(rtwdev);
+}
+
+static void _action_wl_scan(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_dbcc_info *wl_dinfo = &wl->dbcc_info;
+
+	if (rtwdev->dbcc_en) {
+		if (wl_dinfo->real_band[RTW89_PHY_0] != RTW89_BAND_2G &&
+		    wl_dinfo->real_band[RTW89_PHY_1] != RTW89_BAND_2G)
+			_action_wl_5g(rtwdev);
+		else
+			_action_by_bt(rtwdev);
+	} else {
+		if (wl->scan_info.band[RTW89_PHY_0] != RTW89_BAND_2G)
+			_action_wl_5g(rtwdev);
+		else
+			_action_by_bt(rtwdev);
+	}
+}
+
+static void _action_wl_25g_mcc(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W25G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) {
+		if (btc->cx.bt.link_info.profile_cnt.now == 0)
+			_set_policy(rtwdev, BTC_CXP_OFFE_DEF2,
+				    BTC_ACT_WL_25G_MCC);
+		else
+			_set_policy(rtwdev, BTC_CXP_OFFE_DEF,
+				    BTC_ACT_WL_25G_MCC);
+	} else { /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_25G_MCC);
+	}
+}
+
+static void _action_wl_2g_mcc(struct rtw89_dev *rtwdev)
+{	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) { /* shared-antenna */
+		if (btc->cx.bt.link_info.profile_cnt.now == 0)
+			_set_policy(rtwdev, BTC_CXP_OFFE_DEF2,
+				    BTC_ACT_WL_2G_MCC);
+		else
+			_set_policy(rtwdev, BTC_CXP_OFFE_DEF,
+				    BTC_ACT_WL_2G_MCC);
+	} else { /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_2G_MCC);
+	}
+}
+
+static void _action_wl_2g_scc(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) { /* shared-antenna */
+		if (btc->cx.bt.link_info.profile_cnt.now == 0)
+			_set_policy(rtwdev,
+				    BTC_CXP_OFFE_DEF2, BTC_ACT_WL_2G_SCC);
+		else
+			_set_policy(rtwdev,
+				    BTC_CXP_OFFE_DEF, BTC_ACT_WL_2G_SCC);
+	} else { /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_2G_SCC);
+	}
+}
+
+static void _action_wl_2g_ap(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) {
+		if (btc->cx.bt.link_info.profile_cnt.now == 0)
+			_set_policy(rtwdev, BTC_CXP_OFFE_DEF2,
+				    BTC_ACT_WL_2G_AP);
+		else
+			_set_policy(rtwdev, BTC_CXP_OFFE_DEF, BTC_ACT_WL_2G_AP);
+	} else {/* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_2G_AP);
+	}
+}
+
+static void _action_wl_2g_go(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) { /* shared-antenna */
+		if (btc->cx.bt.link_info.profile_cnt.now == 0)
+			_set_policy(rtwdev,
+				    BTC_CXP_OFFE_DEF2, BTC_ACT_WL_2G_GO);
+		else
+			_set_policy(rtwdev,
+				    BTC_CXP_OFFE_DEF, BTC_ACT_WL_2G_GO);
+	} else { /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_2G_GO);
+	}
+}
+
+static void _action_wl_2g_gc(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) { /* shared-antenna */
+		_action_by_bt(rtwdev);
+	} else {/* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_2G_GC);
+	}
+}
+
+static void _action_wl_2g_nan(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	_set_ant(rtwdev, NM_EXEC, BTC_PHY_ALL, BTC_ANT_W2G);
+
+	if (btc->mdinfo.ant.type == BTC_ANT_SHARED) { /* shared-antenna */
+		if (btc->cx.bt.link_info.profile_cnt.now == 0)
+			_set_policy(rtwdev,
+				    BTC_CXP_OFFE_DEF2, BTC_ACT_WL_2G_NAN);
+		else
+			_set_policy(rtwdev,
+				    BTC_CXP_OFFE_DEF, BTC_ACT_WL_2G_NAN);
+	} else { /* dedicated-antenna */
+		_set_policy(rtwdev, BTC_CXP_OFF_EQ0, BTC_ACT_WL_2G_NAN);
+	}
+}
+
+static u32 _read_scbd(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	u32 scbd_val = 0;
+
+	if (!chip->scbd)
+		return 0;
+
+	scbd_val = rtw89_mac_get_sb(rtwdev);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], read scbd: 0x%08x\n",
+		    scbd_val);
+
+	btc->cx.cnt_bt[BTC_BCNT_SCBDREAD]++;
+	return scbd_val;
+}
+
+static void _write_scbd(struct rtw89_dev *rtwdev, u32 val, bool state)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	u32 scbd_val = 0;
+
+	if (!chip->scbd)
+		return;
+
+	scbd_val = state ? wl->scbd | val : wl->scbd & ~val;
+
+	if (scbd_val == wl->scbd)
+		return;
+	rtw89_mac_cfg_sb(rtwdev, scbd_val);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], write scbd: 0x%08x\n",
+		    scbd_val);
+	wl->scbd = scbd_val;
+
+	btc->cx.cnt_wl[BTC_WCNT_SCBDUPDATE]++;
+}
+
+static u8
+_update_rssi_state(struct rtw89_dev *rtwdev, u8 pre_state, u8 rssi, u8 thresh)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	u8 next_state, tol = chip->rssi_tol;
+
+	if (pre_state == BTC_RSSI_ST_LOW ||
+	    pre_state == BTC_RSSI_ST_STAY_LOW) {
+		if (rssi >= (thresh + tol))
+			next_state = BTC_RSSI_ST_HIGH;
+		else
+			next_state = BTC_RSSI_ST_STAY_LOW;
+	} else {
+		if (rssi < thresh)
+			next_state = BTC_RSSI_ST_LOW;
+		else
+			next_state = BTC_RSSI_ST_STAY_HIGH;
+	}
+
+	return next_state;
+}
+
+static
+void _update_dbcc_band(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	btc->cx.wl.dbcc_info.real_band[phy_idx] =
+		btc->cx.wl.scan_info.phy_map & BIT(phy_idx) ?
+		btc->cx.wl.dbcc_info.scan_band[phy_idx] :
+		btc->cx.wl.dbcc_info.op_band[phy_idx];
+}
+
+static void _update_wl_info(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_link_info *wl_linfo = wl->link_info;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	struct rtw89_btc_wl_dbcc_info *wl_dinfo = &wl->dbcc_info;
+	u8 i, cnt_connect = 0, cnt_connecting = 0, cnt_active = 0;
+	u8 cnt_2g = 0, cnt_5g = 0, phy;
+	u32 wl_2g_ch[2] = {0}, wl_5g_ch[2] = {0};
+	bool b2g = false, b5g = false, client_joined = false;
+
+	memset(wl_rinfo, 0, sizeof(*wl_rinfo));
+
+	for (i = 0; i < RTW89_MAX_HW_PORT_NUM; i++) {
+		/* check if role active? */
+		if (!wl_linfo[i].active)
+			continue;
+
+		cnt_active++;
+		wl_rinfo->active_role[cnt_active - 1].role = wl_linfo[i].role;
+		wl_rinfo->active_role[cnt_active - 1].pid = wl_linfo[i].pid;
+		wl_rinfo->active_role[cnt_active - 1].phy = wl_linfo[i].phy;
+		wl_rinfo->active_role[cnt_active - 1].band = wl_linfo[i].band;
+		wl_rinfo->active_role[cnt_active - 1].noa = (u8)wl_linfo[i].noa;
+		wl_rinfo->active_role[cnt_active - 1].connected = 0;
+
+		wl->port_id[wl_linfo[i].role] = wl_linfo[i].pid;
+
+		phy = wl_linfo[i].phy;
+
+		/* check dbcc role */
+		if (rtwdev->dbcc_en && phy < RTW89_PHY_MAX) {
+			wl_dinfo->role[phy] = wl_linfo[i].role;
+			wl_dinfo->op_band[phy] = wl_linfo[i].band;
+			_update_dbcc_band(rtwdev, phy);
+			_fw_set_drv_info(rtwdev, CXDRVINFO_DBCC);
+		}
+
+		if (wl_linfo[i].connected == MLME_NO_LINK) {
+			continue;
+		} else if (wl_linfo[i].connected == MLME_LINKING) {
+			cnt_connecting++;
+		} else {
+			cnt_connect++;
+			if ((wl_linfo[i].role == RTW89_WIFI_ROLE_P2P_GO ||
+			     wl_linfo[i].role == RTW89_WIFI_ROLE_AP) &&
+			     wl_linfo[i].client_cnt > 1)
+				client_joined = true;
+		}
+
+		wl_rinfo->role_map.val |= BIT(wl_linfo[i].role);
+		wl_rinfo->active_role[cnt_active - 1].ch = wl_linfo[i].ch;
+		wl_rinfo->active_role[cnt_active - 1].bw = wl_linfo[i].bw;
+		wl_rinfo->active_role[cnt_active - 1].connected = 1;
+
+		/* only care 2 roles + BT coex */
+		if (wl_linfo[i].band != RTW89_BAND_2G) {
+			if (cnt_5g <= ARRAY_SIZE(wl_5g_ch) - 1)
+				wl_5g_ch[cnt_5g] = wl_linfo[i].ch;
+			cnt_5g++;
+			b5g = true;
+		} else {
+			if (cnt_2g <= ARRAY_SIZE(wl_2g_ch) - 1)
+				wl_2g_ch[cnt_2g] = wl_linfo[i].ch;
+			cnt_2g++;
+			b2g = true;
+		}
+	}
+
+	wl_rinfo->connect_cnt = cnt_connect;
+
+	/* Be careful to change the following sequence!! */
+	if (cnt_connect == 0) {
+		wl_rinfo->link_mode = BTC_WLINK_NOLINK;
+		wl_rinfo->role_map.role.none = 1;
+	} else if (!b2g && b5g) {
+		wl_rinfo->link_mode = BTC_WLINK_5G;
+	} else if (wl_rinfo->role_map.role.nan) {
+		wl_rinfo->link_mode = BTC_WLINK_2G_NAN;
+	} else if (cnt_connect > BTC_TDMA_WLROLE_MAX) {
+		wl_rinfo->link_mode = BTC_WLINK_OTHER;
+	} else  if (b2g && b5g && cnt_connect == 2) {
+		if (rtwdev->dbcc_en) {
+			switch (wl_dinfo->role[RTW89_PHY_0]) {
+			case RTW89_WIFI_ROLE_STATION:
+				wl_rinfo->link_mode = BTC_WLINK_2G_STA;
+				break;
+			case RTW89_WIFI_ROLE_P2P_GO:
+				wl_rinfo->link_mode = BTC_WLINK_2G_GO;
+				break;
+			case RTW89_WIFI_ROLE_P2P_CLIENT:
+				wl_rinfo->link_mode = BTC_WLINK_2G_GC;
+				break;
+			case RTW89_WIFI_ROLE_AP:
+				wl_rinfo->link_mode = BTC_WLINK_2G_AP;
+				break;
+			default:
+				wl_rinfo->link_mode = BTC_WLINK_OTHER;
+				break;
+			}
+		} else {
+			wl_rinfo->link_mode = BTC_WLINK_25G_MCC;
+		}
+	} else if (!b5g && cnt_connect == 2) {
+		if (wl_rinfo->role_map.role.station &&
+		    (wl_rinfo->role_map.role.p2p_go ||
+		    wl_rinfo->role_map.role.p2p_gc ||
+		    wl_rinfo->role_map.role.ap)) {
+			if (wl_2g_ch[0] == wl_2g_ch[1])
+				wl_rinfo->link_mode = BTC_WLINK_2G_SCC;
+			else
+				wl_rinfo->link_mode = BTC_WLINK_2G_MCC;
+		} else {
+			wl_rinfo->link_mode = BTC_WLINK_2G_MCC;
+		}
+	} else if (!b5g && cnt_connect == 1) {
+		if (wl_rinfo->role_map.role.station)
+			wl_rinfo->link_mode = BTC_WLINK_2G_STA;
+		else if (wl_rinfo->role_map.role.ap)
+			wl_rinfo->link_mode = BTC_WLINK_2G_AP;
+		else if (wl_rinfo->role_map.role.p2p_go)
+			wl_rinfo->link_mode = BTC_WLINK_2G_GO;
+		else if (wl_rinfo->role_map.role.p2p_gc)
+			wl_rinfo->link_mode = BTC_WLINK_2G_GC;
+		else
+			wl_rinfo->link_mode = BTC_WLINK_OTHER;
+	}
+
+	/* if no client_joined, don't care P2P-GO/AP role */
+	if (wl_rinfo->role_map.role.p2p_go || wl_rinfo->role_map.role.ap) {
+		if (!client_joined) {
+			if (wl_rinfo->link_mode == BTC_WLINK_2G_SCC ||
+			    wl_rinfo->link_mode == BTC_WLINK_2G_MCC) {
+				wl_rinfo->link_mode = BTC_WLINK_2G_STA;
+				wl_rinfo->connect_cnt = 1;
+			} else if (wl_rinfo->link_mode == BTC_WLINK_2G_GO ||
+				 wl_rinfo->link_mode == BTC_WLINK_2G_AP) {
+				wl_rinfo->link_mode = BTC_WLINK_NOLINK;
+				wl_rinfo->connect_cnt = 0;
+			}
+		}
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], cnt_connect = %d, link_mode = %d\n",
+		    cnt_connect, wl_rinfo->link_mode);
+
+	_fw_set_drv_info(rtwdev, CXDRVINFO_ROLE);
+}
+
+#define BTC_CHK_HANG_MAX 3
+#define BTC_SCB_INV_VALUE GENMASK(31, 0)
+
+void rtw89_coex_act1_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						coex_act1_work.work);
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &rtwdev->btc.dm;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): enter\n", __func__);
+	dm->cnt_notify[BTC_NCNT_TIMER]++;
+	if (wl->status.map._4way)
+		wl->status.map._4way = false;
+	if (wl->status.map.connecting)
+		wl->status.map.connecting = false;
+
+	_run_coex(rtwdev, BTC_RSN_ACT1_WORK);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+void rtw89_coex_bt_devinfo_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						coex_bt_devinfo_work.work);
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &rtwdev->btc.dm;
+	struct rtw89_btc_bt_a2dp_desc *a2dp = &btc->cx.bt.link_info.a2dp_desc;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): enter\n", __func__);
+	dm->cnt_notify[BTC_NCNT_TIMER]++;
+	a2dp->play_latency = 0;
+	_run_coex(rtwdev, BTC_RSN_BT_DEVINFO_WORK);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+void rtw89_coex_rfk_chk_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						coex_rfk_chk_work.work);
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &rtwdev->btc.dm;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): enter\n", __func__);
+	dm->cnt_notify[BTC_NCNT_TIMER]++;
+	if (wl->rfk_info.state != BTC_WRFK_STOP) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): RFK timeout\n", __func__);
+		cx->cnt_wl[BTC_WCNT_RFK_TIMEOUT]++;
+		dm->error.map.wl_rfk_timeout = true;
+		wl->rfk_info.state = BTC_WRFK_STOP;
+		_write_scbd(rtwdev, BTC_WSCB_WLRFK, false);
+		_run_coex(rtwdev, BTC_RSN_RFK_CHK_WORK);
+	}
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static void _update_bt_scbd(struct rtw89_dev *rtwdev, bool only_update)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	u32 val;
+	bool status_change = false;
+
+	if (!chip->scbd)
+		return;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s\n", __func__);
+
+	val = _read_scbd(rtwdev);
+	if (val == BTC_SCB_INV_VALUE) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return by invalid scbd value\n",
+			    __func__);
+		return;
+	}
+
+	if (!(val & BTC_BSCB_ON) ||
+	    btc->dm.cnt_dm[BTC_DCNT_BTCNT_FREEZE] >= BTC_CHK_HANG_MAX)
+		bt->enable.now = 0;
+	else
+		bt->enable.now = 1;
+
+	if (bt->enable.now != bt->enable.last)
+		status_change = true;
+
+	/* reset bt info if bt re-enable */
+	if (bt->enable.now && !bt->enable.last) {
+		_reset_btc_var(rtwdev, BTC_RESET_BTINFO);
+		cx->cnt_bt[BTC_BCNT_REENABLE]++;
+		bt->enable.now = 1;
+	}
+
+	bt->enable.last = bt->enable.now;
+	bt->scbd = val;
+	bt->mbx_avl = !!(val & BTC_BSCB_ACT);
+
+	if (bt->whql_test != !!(val & BTC_BSCB_WHQL))
+		status_change = true;
+
+	bt->whql_test = !!(val & BTC_BSCB_WHQL);
+	bt->btg_type = val & BTC_BSCB_BT_S1 ? BTC_BT_BTG : BTC_BT_ALONE;
+	bt->link_info.a2dp_desc.active = !!(val & BTC_BSCB_A2DP_ACT);
+
+	/* if rfk run 1->0 */
+	if (bt->rfk_info.map.run && !(val & BTC_BSCB_RFK_RUN))
+		status_change = true;
+
+	bt->rfk_info.map.run  = !!(val & BTC_BSCB_RFK_RUN);
+	bt->rfk_info.map.req = !!(val & BTC_BSCB_RFK_REQ);
+	bt->hi_lna_rx = !!(val & BTC_BSCB_BT_HILNA);
+	bt->link_info.status.map.connect = !!(val & BTC_BSCB_BT_CONNECT);
+	bt->run_patch_code = !!(val & BTC_BSCB_PATCH_CODE);
+
+	if (!only_update && status_change)
+		_run_coex(rtwdev, BTC_RSN_UPDATE_BT_SCBD);
+}
+
+static bool _chk_wl_rfk_request(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+
+	_update_bt_scbd(rtwdev, true);
+
+	cx->cnt_wl[BTC_WCNT_RFK_REQ]++;
+
+	if ((bt->rfk_info.map.run || bt->rfk_info.map.req) &&
+	    !bt->rfk_info.map.timeout) {
+		cx->cnt_wl[BTC_WCNT_RFK_REJECT]++;
+	} else {
+		cx->cnt_wl[BTC_WCNT_RFK_GO]++;
+		return true;
+	}
+	return false;
+}
+
+static
+void _run_coex(struct rtw89_dev *rtwdev, enum btc_reason_and_action reason)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &rtwdev->btc.dm;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+	u8 mode = wl_rinfo->link_mode;
+
+	lockdep_assert_held(&rtwdev->mutex);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): reason=%d, mode=%d\n",
+		    __func__, reason, mode);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): wl_only=%d, bt_only=%d\n",
+		    __func__, dm->wl_only, dm->bt_only);
+
+	dm->run_reason = reason;
+	_update_dm_step(rtwdev, reason);
+	_update_btc_state_map(rtwdev);
+
+	/* Be careful to change the following function sequence!! */
+	if (btc->ctrl.manual) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return for Manual CTRL!!\n",
+			    __func__);
+		return;
+	}
+
+	if (btc->ctrl.igno_bt &&
+	    (reason == BTC_RSN_UPDATE_BT_INFO ||
+	     reason == BTC_RSN_UPDATE_BT_SCBD)) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return for Stop Coex DM!!\n",
+			    __func__);
+		return;
+	}
+
+	if (!wl->status.map.init_ok) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return for WL init fail!!\n",
+			    __func__);
+		return;
+	}
+
+	if (wl->status.map.rf_off_pre == wl->status.map.rf_off &&
+	    wl->status.map.lps_pre == wl->status.map.lps &&
+	    (reason == BTC_RSN_NTFY_POWEROFF ||
+	    reason == BTC_RSN_NTFY_RADIO_STATE)) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return for WL rf off state no change!!\n",
+			    __func__);
+		return;
+	}
+
+	dm->cnt_dm[BTC_DCNT_RUN]++;
+
+	if (btc->ctrl.always_freerun) {
+		_action_freerun(rtwdev);
+		btc->ctrl.igno_bt = true;
+		goto exit;
+	}
+
+	if (dm->wl_only) {
+		_action_wl_only(rtwdev);
+		btc->ctrl.igno_bt = true;
+		goto exit;
+	}
+
+	if (wl->status.map.rf_off || wl->status.map.lps || dm->bt_only) {
+		_action_wl_off(rtwdev);
+		btc->ctrl.igno_bt = true;
+		goto exit;
+	}
+
+	btc->ctrl.igno_bt = false;
+	dm->freerun = false;
+
+	if (reason == BTC_RSN_NTFY_INIT) {
+		_action_wl_init(rtwdev);
+		goto exit;
+	}
+
+	if (!cx->bt.enable.now && !cx->other.type) {
+		_action_bt_off(rtwdev);
+		goto exit;
+	}
+
+	if (cx->bt.whql_test) {
+		_action_bt_whql(rtwdev);
+		goto exit;
+	}
+
+	if (wl->rfk_info.state != BTC_WRFK_STOP) {
+		_action_wl_rfk(rtwdev);
+		goto exit;
+	}
+
+	if (cx->state_map == BTC_WLINKING) {
+		if (mode == BTC_WLINK_NOLINK || mode == BTC_WLINK_2G_STA ||
+		    mode == BTC_WLINK_5G) {
+			_action_wl_scan(rtwdev);
+			goto exit;
+		}
+	}
+
+	if (wl->status.map.scan) {
+		_action_wl_scan(rtwdev);
+		goto exit;
+	}
+
+	switch (mode) {
+	case BTC_WLINK_NOLINK:
+		_action_wl_nc(rtwdev);
+		break;
+	case BTC_WLINK_2G_STA:
+		_action_wl_2g_sta(rtwdev);
+		break;
+	case BTC_WLINK_2G_AP:
+		_action_wl_2g_ap(rtwdev);
+		break;
+	case BTC_WLINK_2G_GO:
+		_action_wl_2g_go(rtwdev);
+		break;
+	case BTC_WLINK_2G_GC:
+		_action_wl_2g_gc(rtwdev);
+		break;
+	case BTC_WLINK_2G_SCC:
+		_action_wl_2g_scc(rtwdev);
+		break;
+	case BTC_WLINK_2G_MCC:
+		_action_wl_2g_mcc(rtwdev);
+		break;
+	case BTC_WLINK_25G_MCC:
+		_action_wl_25g_mcc(rtwdev);
+		break;
+	case BTC_WLINK_5G:
+		_action_wl_5g(rtwdev);
+		break;
+	case BTC_WLINK_2G_NAN:
+		_action_wl_2g_nan(rtwdev);
+		break;
+	default:
+		_action_wl_other(rtwdev);
+		break;
+	}
+
+exit:
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): exit\n", __func__);
+	_action_common(rtwdev);
+}
+
+void rtw89_btc_ntfy_poweron(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+	btc->dm.cnt_notify[BTC_NCNT_POWER_ON]++;
+}
+
+void rtw89_btc_ntfy_poweroff(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): !!\n", __func__);
+	btc->dm.cnt_notify[BTC_NCNT_POWER_OFF]++;
+
+	btc->cx.wl.status.map.rf_off = 1;
+
+	_write_scbd(rtwdev, BTC_WSCB_ALL, false);
+	_run_coex(rtwdev, BTC_RSN_NTFY_POWEROFF);
+
+	rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_ALL, 0);
+
+	btc->cx.wl.status.map.rf_off_pre = btc->cx.wl.status.map.rf_off;
+}
+
+static void _set_init_info(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	dm->init_info.wl_only = (u8)dm->wl_only;
+	dm->init_info.bt_only = (u8)dm->bt_only;
+	dm->init_info.wl_init_ok = (u8)wl->status.map.init_ok;
+	dm->init_info.dbcc_en = rtwdev->dbcc_en;
+	dm->init_info.cx_other = btc->cx.other.type;
+	dm->init_info.wl_guard_ch = chip->afh_guard_ch;
+	dm->init_info.module = btc->mdinfo;
+}
+
+void rtw89_btc_ntfy_init(struct rtw89_dev *rtwdev, u8 mode)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &rtwdev->btc.dm;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	_reset_btc_var(rtwdev, BTC_RESET_ALL);
+	btc->dm.run_reason = BTC_RSN_NONE;
+	btc->dm.run_action = BTC_ACT_NONE;
+	btc->ctrl.igno_bt = true;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): mode=%d\n", __func__, mode);
+
+	dm->cnt_notify[BTC_NCNT_INIT_COEX]++;
+	dm->wl_only = mode == BTC_MODE_WL ? 1 : 0;
+	dm->bt_only = mode == BTC_MODE_BT ? 1 : 0;
+	wl->status.map.rf_off = mode == BTC_MODE_WLOFF ? 1 : 0;
+
+	chip->ops->btc_set_rfe(rtwdev);
+	chip->ops->btc_init_cfg(rtwdev);
+
+	if (!wl->status.map.init_ok) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return for WL init fail!!\n",
+			    __func__);
+		dm->error.map.init = true;
+		return;
+	}
+
+	_write_scbd(rtwdev,
+		    BTC_WSCB_ACTIVE | BTC_WSCB_ON | BTC_WSCB_BTLOG, true);
+	_update_bt_scbd(rtwdev, true);
+	if (rtw89_mac_get_ctrl_path(rtwdev)) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): PTA owner warning!!\n",
+			    __func__);
+		dm->error.map.pta_owner = true;
+	}
+
+	_set_init_info(rtwdev);
+	_set_wl_tx_power(rtwdev, RTW89_BTC_WL_DEF_TX_PWR);
+	rtw89_btc_fw_set_slots(rtwdev, CXST_MAX, dm->slot);
+	btc_fw_set_monreg(rtwdev);
+	_fw_set_drv_info(rtwdev, CXDRVINFO_INIT);
+	_fw_set_drv_info(rtwdev, CXDRVINFO_CTRL);
+
+	_run_coex(rtwdev, BTC_RSN_NTFY_INIT);
+}
+
+void rtw89_btc_ntfy_scan_start(struct rtw89_dev *rtwdev, u8 phy_idx, u8 band)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): phy_idx=%d, band=%d\n",
+		    __func__, phy_idx, band);
+	btc->dm.cnt_notify[BTC_NCNT_SCAN_START]++;
+	wl->status.map.scan = true;
+	wl->scan_info.band[phy_idx] = band;
+	wl->scan_info.phy_map |= BIT(phy_idx);
+	_fw_set_drv_info(rtwdev, CXDRVINFO_SCAN);
+
+	if (rtwdev->dbcc_en) {
+		wl->dbcc_info.scan_band[phy_idx] = band;
+		_update_dbcc_band(rtwdev, phy_idx);
+		_fw_set_drv_info(rtwdev, CXDRVINFO_DBCC);
+	}
+
+	_run_coex(rtwdev, BTC_RSN_NTFY_SCAN_START);
+}
+
+void rtw89_btc_ntfy_scan_finish(struct rtw89_dev *rtwdev, u8 phy_idx)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): phy_idx=%d\n", __func__, phy_idx);
+	btc->dm.cnt_notify[BTC_NCNT_SCAN_FINISH]++;
+
+	wl->status.map.scan = false;
+	wl->scan_info.phy_map &= ~BIT(phy_idx);
+	_fw_set_drv_info(rtwdev, CXDRVINFO_SCAN);
+
+	if (rtwdev->dbcc_en) {
+		_update_dbcc_band(rtwdev, phy_idx);
+		_fw_set_drv_info(rtwdev, CXDRVINFO_DBCC);
+	}
+
+	_run_coex(rtwdev, BTC_RSN_NTFY_SCAN_FINISH);
+}
+
+void rtw89_btc_ntfy_switch_band(struct rtw89_dev *rtwdev, u8 phy_idx, u8 band)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): phy_idx=%d, band=%d\n",
+		    __func__, phy_idx, band);
+	btc->dm.cnt_notify[BTC_NCNT_SWITCH_BAND]++;
+
+	wl->scan_info.band[phy_idx] = band;
+	wl->scan_info.phy_map |= BIT(phy_idx);
+	_fw_set_drv_info(rtwdev, CXDRVINFO_SCAN);
+
+	if (rtwdev->dbcc_en) {
+		wl->dbcc_info.scan_band[phy_idx] = band;
+		_update_dbcc_band(rtwdev, phy_idx);
+		_fw_set_drv_info(rtwdev, CXDRVINFO_DBCC);
+	}
+	_run_coex(rtwdev, BTC_RSN_NTFY_SWBAND);
+}
+
+void rtw89_btc_ntfy_specific_packet(struct rtw89_dev *rtwdev,
+				    enum btc_pkt_type pkt_type)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_bt_link_info *b = &cx->bt.link_info;
+	struct rtw89_btc_bt_hfp_desc *hfp = &b->hfp_desc;
+	struct rtw89_btc_bt_hid_desc *hid = &b->hid_desc;
+	u32 cnt;
+	u32 delay = RTW89_COEX_ACT1_WORK_PERIOD;
+	bool delay_work = false;
+
+	switch (pkt_type) {
+	case PACKET_DHCP:
+		cnt = ++cx->cnt_wl[BTC_WCNT_DHCP];
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): DHCP cnt=%d\n", __func__, cnt);
+		wl->status.map.connecting = true;
+		delay_work = true;
+		break;
+	case PACKET_EAPOL:
+		cnt = ++cx->cnt_wl[BTC_WCNT_EAPOL];
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): EAPOL cnt=%d\n", __func__, cnt);
+		wl->status.map._4way = true;
+		delay_work = true;
+		if (hfp->exist || hid->exist)
+			delay /= 2;
+		break;
+	case PACKET_EAPOL_END:
+		cnt = ++cx->cnt_wl[BTC_WCNT_EAPOL];
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): EAPOL_End cnt=%d\n",
+			    __func__, cnt);
+		wl->status.map._4way = false;
+		cancel_delayed_work(&rtwdev->coex_act1_work);
+		break;
+	case PACKET_ARP:
+		cnt = ++cx->cnt_wl[BTC_WCNT_ARP];
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): ARP cnt=%d\n", __func__, cnt);
+		return;
+	case PACKET_ICMP:
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): ICMP pkt\n", __func__);
+		return;
+	default:
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): unknown packet type %d\n",
+			    __func__, pkt_type);
+		return;
+	}
+
+	if (delay_work) {
+		cancel_delayed_work(&rtwdev->coex_act1_work);
+		ieee80211_queue_delayed_work(rtwdev->hw,
+					     &rtwdev->coex_act1_work, delay);
+	}
+
+	btc->dm.cnt_notify[BTC_NCNT_SPECIAL_PACKET]++;
+	_run_coex(rtwdev, BTC_RSN_NTFY_SPECIFIC_PACKET);
+}
+
+void rtw89_btc_ntfy_eapol_packet_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						btc.eapol_notify_work);
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	rtw89_btc_ntfy_specific_packet(rtwdev, PACKET_EAPOL);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+void rtw89_btc_ntfy_arp_packet_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						btc.arp_notify_work);
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_btc_ntfy_specific_packet(rtwdev, PACKET_ARP);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+void rtw89_btc_ntfy_dhcp_packet_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						btc.dhcp_notify_work);
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	rtw89_btc_ntfy_specific_packet(rtwdev, PACKET_DHCP);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+void rtw89_btc_ntfy_icmp_packet_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						btc.icmp_notify_work);
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	rtw89_btc_ntfy_specific_packet(rtwdev, PACKET_ICMP);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static void _update_bt_info(struct rtw89_dev *rtwdev, u8 *buf, u32 len)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+	struct rtw89_btc_bt_link_info *b = &bt->link_info;
+	struct rtw89_btc_bt_hfp_desc *hfp = &b->hfp_desc;
+	struct rtw89_btc_bt_hid_desc *hid = &b->hid_desc;
+	struct rtw89_btc_bt_a2dp_desc *a2dp = &b->a2dp_desc;
+	struct rtw89_btc_bt_pan_desc *pan = &b->pan_desc;
+	union btc_btinfo btinfo;
+
+	if (buf[BTC_BTINFO_L1] != 6)
+		return;
+
+	if (!memcmp(bt->raw_info, buf, BTC_BTINFO_MAX)) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): return by bt-info duplicate!!\n",
+			    __func__);
+		cx->cnt_bt[BTC_BCNT_INFOSAME]++;
+		return;
+	}
+
+	memcpy(bt->raw_info, buf, BTC_BTINFO_MAX);
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): bt_info[2]=0x%02x\n",
+		    __func__, bt->raw_info[2]);
+
+	/* reset to mo-connect before update */
+	b->status.val = BTC_BLINK_NOCONNECT;
+	b->profile_cnt.last = b->profile_cnt.now;
+	b->relink.last = b->relink.now;
+	a2dp->exist_last = a2dp->exist;
+	b->multi_link.last = b->multi_link.now;
+	bt->inq_pag.last = bt->inq_pag.now;
+	b->profile_cnt.now = 0;
+	hid->type = 0;
+
+	/* parse raw info low-Byte2 */
+	btinfo.val = bt->raw_info[BTC_BTINFO_L2];
+	b->status.map.connect = btinfo.lb2.connect;
+	b->status.map.sco_busy = btinfo.lb2.sco_busy;
+	b->status.map.acl_busy = btinfo.lb2.acl_busy;
+	b->status.map.inq_pag = btinfo.lb2.inq_pag;
+	bt->inq_pag.now = btinfo.lb2.inq_pag;
+	cx->cnt_bt[BTC_BCNT_INQPAG] += !!(bt->inq_pag.now && !bt->inq_pag.last);
+
+	hfp->exist = btinfo.lb2.hfp;
+	b->profile_cnt.now += (u8)hfp->exist;
+	hid->exist = btinfo.lb2.hid;
+	b->profile_cnt.now += (u8)hid->exist;
+	a2dp->exist = btinfo.lb2.a2dp;
+	b->profile_cnt.now += (u8)a2dp->exist;
+	pan->active = btinfo.lb2.pan;
+
+	/* parse raw info low-Byte3 */
+	btinfo.val = bt->raw_info[BTC_BTINFO_L3];
+	if (btinfo.lb3.retry != 0)
+		cx->cnt_bt[BTC_BCNT_RETRY]++;
+	b->cqddr = btinfo.lb3.cqddr;
+	cx->cnt_bt[BTC_BCNT_INQ] += !!(btinfo.lb3.inq && !bt->inq);
+	bt->inq = btinfo.lb3.inq;
+	cx->cnt_bt[BTC_BCNT_PAGE] += !!(btinfo.lb3.pag && !bt->pag);
+	bt->pag = btinfo.lb3.pag;
+
+	b->status.map.mesh_busy = btinfo.lb3.mesh_busy;
+	/* parse raw info high-Byte0 */
+	btinfo.val = bt->raw_info[BTC_BTINFO_H0];
+	/* raw val is dBm unit, translate from -100~ 0dBm to 0~100%*/
+	b->rssi = chip->ops->btc_get_bt_rssi(rtwdev, btinfo.hb0.rssi);
+
+	/* parse raw info high-Byte1 */
+	btinfo.val = bt->raw_info[BTC_BTINFO_H1];
+	b->status.map.ble_connect = btinfo.hb1.ble_connect;
+	if (btinfo.hb1.ble_connect)
+		hid->type |= (hid->exist ? BTC_HID_BLE : BTC_HID_RCU);
+
+	cx->cnt_bt[BTC_BCNT_REINIT] += !!(btinfo.hb1.reinit && !bt->reinit);
+	bt->reinit = btinfo.hb1.reinit;
+	cx->cnt_bt[BTC_BCNT_RELINK] += !!(btinfo.hb1.relink && !b->relink.now);
+	b->relink.now = btinfo.hb1.relink;
+	cx->cnt_bt[BTC_BCNT_IGNOWL] += !!(btinfo.hb1.igno_wl && !bt->igno_wl);
+	bt->igno_wl = btinfo.hb1.igno_wl;
+
+	if (bt->igno_wl && !cx->wl.status.map.rf_off)
+		_set_bt_ignore_wlan_act(rtwdev, false);
+
+	hid->type |= (btinfo.hb1.voice ? BTC_HID_RCU_VOICE : 0);
+	bt->ble_scan_en = btinfo.hb1.ble_scan;
+
+	cx->cnt_bt[BTC_BCNT_ROLESW] += !!(btinfo.hb1.role_sw && !b->role_sw);
+	b->role_sw = btinfo.hb1.role_sw;
+
+	b->multi_link.now = btinfo.hb1.multi_link;
+
+	/* parse raw info high-Byte2 */
+	btinfo.val = bt->raw_info[BTC_BTINFO_H2];
+	pan->exist = btinfo.hb2.pan_active;
+	b->profile_cnt.now += (u8)pan->exist;
+
+	cx->cnt_bt[BTC_BCNT_AFH] += !!(btinfo.hb2.afh_update && !b->afh_update);
+	b->afh_update = btinfo.hb2.afh_update;
+	a2dp->active = btinfo.hb2.a2dp_active;
+	b->slave_role = btinfo.hb2.slave;
+	hid->slot_info = btinfo.hb2.hid_slot;
+	hid->pair_cnt = btinfo.hb2.hid_cnt;
+	hid->type |= (hid->slot_info == BTC_HID_218 ?
+		      BTC_HID_218 : BTC_HID_418);
+	/* parse raw info high-Byte3 */
+	btinfo.val = bt->raw_info[BTC_BTINFO_H3];
+	a2dp->bitpool = btinfo.hb3.a2dp_bitpool;
+
+	if (b->tx_3m != (u32)btinfo.hb3.tx_3m)
+		cx->cnt_bt[BTC_BCNT_RATECHG]++;
+	b->tx_3m = (u32)btinfo.hb3.tx_3m;
+
+	a2dp->sink = btinfo.hb3.a2dp_sink;
+
+	if (b->profile_cnt.now || b->status.map.ble_connect)
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_BT_AFH_MAP, 1);
+	else
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_BT_AFH_MAP, 0);
+
+	if (!a2dp->exist_last && a2dp->exist) {
+		a2dp->vendor_id = 0;
+		a2dp->flush_time = 0;
+		a2dp->play_latency = 1;
+		ieee80211_queue_delayed_work(rtwdev->hw,
+					     &rtwdev->coex_bt_devinfo_work,
+					     RTW89_COEX_BT_DEVINFO_WORK_PERIOD);
+	}
+
+	if (a2dp->exist && (a2dp->flush_time == 0 || a2dp->vendor_id == 0 ||
+			    a2dp->play_latency == 1))
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_BT_DEVICE_INFO, 1);
+	else
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_BT_DEVICE_INFO, 0);
+
+	_run_coex(rtwdev, BTC_RSN_UPDATE_BT_INFO);
+}
+
+enum btc_wl_mode {
+	BTC_WL_MODE_HT = 0,
+	BTC_WL_MODE_VHT = 1,
+	BTC_WL_MODE_HE = 2,
+	BTC_WL_MODE_NUM,
+};
+
+void rtw89_btc_ntfy_role_info(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			      struct rtw89_sta *rtwsta, enum btc_role_state state)
+{
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	struct ieee80211_sta *sta = rtwsta_to_sta(rtwsta);
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_link_info r = {0};
+	struct rtw89_btc_wl_link_info *wlinfo = NULL;
+	u8 mode = 0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], state=%d\n", state);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], role is STA=%d\n",
+		    vif->type == NL80211_IFTYPE_STATION);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], port=%d\n", rtwvif->port);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], band=%d ch=%d bw=%d\n",
+		    hal->current_band_type, hal->current_channel,
+		    hal->current_band_width);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], associated=%d\n",
+		    state == BTC_ROLE_MSTS_STA_CONN_END);
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], bcn_period=%d dtim_period=%d\n",
+		    vif->bss_conf.beacon_int, vif->bss_conf.dtim_period);
+
+	if (rtwsta) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], STA mac_id=%d\n",
+			    rtwsta->mac_id);
+
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], STA support HE=%d VHT=%d HT=%d\n",
+			    sta->he_cap.has_he,
+			    sta->vht_cap.vht_supported,
+			    sta->ht_cap.ht_supported);
+		if (sta->he_cap.has_he)
+			mode |= BIT(BTC_WL_MODE_HE);
+		if (sta->vht_cap.vht_supported)
+			mode |= BIT(BTC_WL_MODE_VHT);
+		if (sta->ht_cap.ht_supported)
+			mode |= BIT(BTC_WL_MODE_HT);
+
+		r.mode = mode;
+	}
+
+	if (rtwvif->wifi_role >= RTW89_WIFI_ROLE_MLME_MAX)
+		return;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], wifi_role=%d\n", rtwvif->wifi_role);
+
+	r.role = rtwvif->wifi_role;
+	r.phy = rtwvif->phy_idx;
+	r.pid = rtwvif->port;
+	r.active = true;
+	r.connected = MLME_LINKED;
+	r.bcn_period = vif->bss_conf.beacon_int;
+	r.dtim_period = vif->bss_conf.dtim_period;
+	r.band = hal->current_band_type;
+	r.ch = hal->current_channel;
+	r.bw = hal->current_band_width;
+	ether_addr_copy(r.mac_addr, rtwvif->mac_addr);
+
+	if (rtwsta && vif->type == NL80211_IFTYPE_STATION)
+		r.mac_id = rtwsta->mac_id;
+
+	btc->dm.cnt_notify[BTC_NCNT_ROLE_INFO]++;
+
+	wlinfo = &wl->link_info[r.pid];
+
+	memcpy(wlinfo, &r, sizeof(*wlinfo));
+	_update_wl_info(rtwdev);
+
+	if (wlinfo->role == RTW89_WIFI_ROLE_STATION &&
+	    wlinfo->connected == MLME_NO_LINK)
+		btc->dm.leak_ap = 0;
+
+	if (state == BTC_ROLE_MSTS_STA_CONN_START)
+		wl->status.map.connecting = 1;
+	else
+		wl->status.map.connecting = 0;
+
+	if (state == BTC_ROLE_MSTS_STA_DIS_CONN)
+		wl->status.map._4way = false;
+
+	_run_coex(rtwdev, BTC_RSN_NTFY_ROLE_INFO);
+}
+
+void rtw89_btc_ntfy_radio_state(struct rtw89_dev *rtwdev, enum btc_rfctrl rf_state)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): rf_state = %d\n",
+		    __func__, rf_state);
+	btc->dm.cnt_notify[BTC_NCNT_RADIO_STATE]++;
+
+	switch (rf_state) {
+	case BTC_RFCTRL_WL_OFF:
+		wl->status.map.rf_off = 1;
+		wl->status.map.lps = 0;
+		break;
+	case BTC_RFCTRL_FW_CTRL:
+		wl->status.map.rf_off = 0;
+		wl->status.map.lps = 1;
+		break;
+	case BTC_RFCTRL_WL_ON:
+	default:
+		wl->status.map.rf_off = 0;
+		wl->status.map.lps = 0;
+		break;
+	}
+
+	if (rf_state == BTC_RFCTRL_WL_ON) {
+		rtw89_btc_fw_en_rpt(rtwdev,
+				    RPT_EN_MREG | RPT_EN_BT_VER_INFO, true);
+		_write_scbd(rtwdev, BTC_WSCB_ACTIVE, true);
+		_update_bt_scbd(rtwdev, true);
+		chip->ops->btc_init_cfg(rtwdev);
+	} else {
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_ALL, false);
+		_write_scbd(rtwdev, BTC_WSCB_ACTIVE | BTC_WSCB_WLBUSY, false);
+	}
+
+	_run_coex(rtwdev, BTC_RSN_NTFY_RADIO_STATE);
+
+	wl->status.map.rf_off_pre = wl->status.map.rf_off;
+	wl->status.map.lps_pre = wl->status.map.lps;
+}
+
+static bool _ntfy_wl_rfk(struct rtw89_dev *rtwdev, u8 phy_path,
+			 enum btc_wl_rfk_type type,
+			 enum btc_wl_rfk_state state)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	bool result = BTC_WRFK_REJECT;
+
+	wl->rfk_info.type = type;
+	wl->rfk_info.path_map = FIELD_GET(BTC_RFK_PATH_MAP, phy_path);
+	wl->rfk_info.phy_map = FIELD_GET(BTC_RFK_PHY_MAP, phy_path);
+	wl->rfk_info.band = FIELD_GET(BTC_RFK_BAND_MAP, phy_path);
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s()_start: phy=0x%x, path=0x%x, type=%d, state=%d\n",
+		    __func__, wl->rfk_info.phy_map, wl->rfk_info.path_map,
+		    type, state);
+
+	switch (state) {
+	case BTC_WRFK_START:
+		result = _chk_wl_rfk_request(rtwdev);
+		wl->rfk_info.state = result ? BTC_WRFK_START : BTC_WRFK_STOP;
+
+		_write_scbd(rtwdev, BTC_WSCB_WLRFK, result);
+
+		btc->dm.cnt_notify[BTC_NCNT_WL_RFK]++;
+		break;
+	case BTC_WRFK_ONESHOT_START:
+	case BTC_WRFK_ONESHOT_STOP:
+		if (wl->rfk_info.state == BTC_WRFK_STOP) {
+			result = BTC_WRFK_REJECT;
+		} else {
+			result = BTC_WRFK_ALLOW;
+			wl->rfk_info.state = state;
+		}
+		break;
+	case BTC_WRFK_STOP:
+		result = BTC_WRFK_ALLOW;
+		wl->rfk_info.state = BTC_WRFK_STOP;
+
+		_write_scbd(rtwdev, BTC_WSCB_WLRFK, false);
+		cancel_delayed_work(&rtwdev->coex_rfk_chk_work);
+		break;
+	default:
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s() warning state=%d\n", __func__, state);
+		break;
+	}
+
+	if (result == BTC_WRFK_ALLOW) {
+		if (wl->rfk_info.state == BTC_WRFK_START ||
+		    wl->rfk_info.state == BTC_WRFK_STOP)
+			_run_coex(rtwdev, BTC_RSN_NTFY_WL_RFK);
+
+		if (wl->rfk_info.state == BTC_WRFK_START)
+			ieee80211_queue_delayed_work(rtwdev->hw,
+						     &rtwdev->coex_rfk_chk_work,
+						     RTW89_COEX_RFK_CHK_WORK_PERIOD);
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s()_finish: rfk_cnt=%d, result=%d\n",
+		    __func__, btc->dm.cnt_notify[BTC_NCNT_WL_RFK], result);
+
+	return result == BTC_WRFK_ALLOW;
+}
+
+void rtw89_btc_ntfy_wl_rfk(struct rtw89_dev *rtwdev, u8 phy_map,
+			   enum btc_wl_rfk_type type,
+			   enum btc_wl_rfk_state state)
+{
+	u8 band;
+	bool allow;
+	int ret;
+
+	band = FIELD_GET(BTC_RFK_BAND_MAP, phy_map);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[RFK] RFK notify (%s / PHY%u / K_type = %u / path_idx = %lu / process = %s)\n",
+		    band == RTW89_BAND_2G ? "2G" :
+		    band == RTW89_BAND_5G ? "5G" : "6G",
+		    !!(FIELD_GET(BTC_RFK_PHY_MAP, phy_map) & BIT(RTW89_PHY_1)),
+		    type,
+		    FIELD_GET(BTC_RFK_PATH_MAP, phy_map),
+		    state == BTC_WRFK_STOP ? "RFK_STOP" :
+		    state == BTC_WRFK_START ? "RFK_START" :
+		    state == BTC_WRFK_ONESHOT_START ? "ONE-SHOT_START" :
+		    "ONE-SHOT_STOP");
+
+	if (state != BTC_WRFK_START || rtwdev->is_bt_iqk_timeout) {
+		_ntfy_wl_rfk(rtwdev, phy_map, type, state);
+		return;
+	}
+
+	ret = read_poll_timeout(_ntfy_wl_rfk, allow, allow, 40, 100000, false,
+				rtwdev, phy_map, type, state);
+	if (ret) {
+		rtw89_warn(rtwdev, "RFK notify timeout\n");
+		rtwdev->is_bt_iqk_timeout = true;
+	}
+}
+
+struct rtw89_btc_wl_sta_iter_data {
+	struct rtw89_dev *rtwdev;
+	u8 busy_all;
+	u8 dir_all;
+	u8 rssi_map_all;
+	bool is_sta_change;
+	bool is_traffic_change;
+};
+
+static void rtw89_btc_ntfy_wl_sta_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_btc_wl_sta_iter_data *iter_data =
+				(struct rtw89_btc_wl_sta_iter_data *)data;
+	struct rtw89_dev *rtwdev = iter_data->rtwdev;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_link_info *link_info = NULL;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_traffic_stats *link_info_t = NULL;
+	struct rtw89_vif *rtwvif = rtwsta->rtwvif;
+	struct rtw89_traffic_stats *stats = &rtwvif->stats;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	u32 last_tx_rate, last_rx_rate;
+	u16 last_tx_lvl, last_rx_lvl;
+	u8 port = rtwvif->port;
+	u8 rssi;
+	u8 busy = 0;
+	u8 dir = 0;
+	u8 rssi_map = 0;
+	u8 i = 0;
+	bool is_sta_change = false, is_traffic_change = false;
+
+	rssi = ewma_rssi_read(&rtwsta->avg_rssi) >> RSSI_FACTOR;
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], rssi=%d\n", rssi);
+
+	link_info = &wl->link_info[port];
+	link_info->stat.traffic = rtwvif->stats;
+	link_info_t = &link_info->stat.traffic;
+
+	if (link_info->connected == MLME_NO_LINK) {
+		link_info->rx_rate_drop_cnt = 0;
+		return;
+	}
+
+	link_info->stat.rssi = rssi;
+	for (i = 0; i < BTC_WL_RSSI_THMAX; i++) {
+		link_info->rssi_state[i] =
+			_update_rssi_state(rtwdev,
+					   link_info->rssi_state[i],
+					   link_info->stat.rssi,
+					   chip->wl_rssi_thres[i]);
+		if (BTC_RSSI_LOW(link_info->rssi_state[i]))
+			rssi_map |= BIT(i);
+
+		if (btc->mdinfo.ant.type == BTC_ANT_DEDICATED &&
+		    BTC_RSSI_CHANGE(link_info->rssi_state[i]))
+			is_sta_change = true;
+	}
+	iter_data->rssi_map_all |= rssi_map;
+
+	last_tx_rate = link_info_t->tx_rate;
+	last_rx_rate = link_info_t->rx_rate;
+	last_tx_lvl = (u16)link_info_t->tx_tfc_lv;
+	last_rx_lvl = (u16)link_info_t->rx_tfc_lv;
+
+	if (stats->tx_tfc_lv != RTW89_TFC_IDLE ||
+	    stats->rx_tfc_lv != RTW89_TFC_IDLE)
+		busy = 1;
+
+	if (stats->tx_tfc_lv > stats->rx_tfc_lv)
+		dir = RTW89_TFC_UL;
+	else
+		dir = RTW89_TFC_DL;
+
+	link_info = &wl->link_info[port];
+	if (link_info->busy != busy || link_info->dir != dir) {
+		is_sta_change = true;
+		link_info->busy = busy;
+		link_info->dir = dir;
+	}
+
+	iter_data->busy_all |= busy;
+	iter_data->dir_all |= BIT(dir);
+
+	if (rtwsta->rx_hw_rate <= RTW89_HW_RATE_CCK2 &&
+	    last_rx_rate > RTW89_HW_RATE_CCK2 &&
+	    link_info_t->rx_tfc_lv > RTW89_TFC_IDLE)
+		link_info->rx_rate_drop_cnt++;
+
+	if (last_tx_rate != rtwsta->ra_report.hw_rate ||
+	    last_rx_rate != rtwsta->rx_hw_rate ||
+	    last_tx_lvl != link_info_t->tx_tfc_lv ||
+	    last_rx_lvl != link_info_t->rx_tfc_lv)
+		is_traffic_change = true;
+
+	link_info_t->tx_rate = rtwsta->ra_report.hw_rate;
+	link_info_t->rx_rate = rtwsta->rx_hw_rate;
+
+	wl->role_info.active_role[port].tx_lvl = (u16)stats->tx_tfc_lv;
+	wl->role_info.active_role[port].rx_lvl = (u16)stats->rx_tfc_lv;
+	wl->role_info.active_role[port].tx_rate = rtwsta->ra_report.hw_rate;
+	wl->role_info.active_role[port].rx_rate = rtwsta->rx_hw_rate;
+
+	if (is_sta_change)
+		iter_data->is_sta_change = true;
+
+	if (is_traffic_change)
+		iter_data->is_traffic_change = true;
+}
+
+#define BTC_NHM_CHK_INTVL 20
+
+void rtw89_btc_ntfy_wl_sta(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_sta_iter_data data = {.rtwdev = rtwdev};
+	u8 i;
+
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_btc_ntfy_wl_sta_iter,
+					  &data);
+
+	wl->rssi_level = 0;
+	btc->dm.cnt_notify[BTC_NCNT_WL_STA]++;
+	for (i = BTC_WL_RSSI_THMAX; i > 0; i--) {
+		/* set RSSI level 4 ~ 0 if rssi bit map match */
+		if (data.rssi_map_all & BIT(i - 1)) {
+			wl->rssi_level = i;
+			break;
+		}
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC, "[BTC], %s(): busy=%d\n",
+		    __func__, !!wl->status.map.busy);
+
+	_write_scbd(rtwdev, BTC_WSCB_WLBUSY, (!!wl->status.map.busy));
+
+	if (data.is_traffic_change)
+		_fw_set_drv_info(rtwdev, CXDRVINFO_ROLE);
+	if (data.is_sta_change) {
+		wl->status.map.busy = data.busy_all;
+		wl->status.map.traffic_dir = data.dir_all;
+		_run_coex(rtwdev, BTC_RSN_NTFY_WL_STA);
+	} else if (btc->dm.cnt_notify[BTC_NCNT_WL_STA] >=
+		   btc->dm.cnt_dm[BTC_DCNT_WL_STA_LAST] + BTC_NHM_CHK_INTVL) {
+		btc->dm.cnt_dm[BTC_DCNT_WL_STA_LAST] =
+			btc->dm.cnt_notify[BTC_NCNT_WL_STA];
+	} else if (btc->dm.cnt_notify[BTC_NCNT_WL_STA] <
+		   btc->dm.cnt_dm[BTC_DCNT_WL_STA_LAST]) {
+		btc->dm.cnt_dm[BTC_DCNT_WL_STA_LAST] =
+		btc->dm.cnt_notify[BTC_NCNT_WL_STA];
+	}
+}
+
+void rtw89_btc_c2h_handle(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			  u32 len, u8 class, u8 func)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	u8 *buf = &skb->data[RTW89_C2H_HEADER_LEN];
+
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): C2H BT len:%d class:%d fun:%d\n",
+		    __func__, len, class, func);
+
+	if (class != BTFC_FW_EVENT)
+		return;
+
+	switch (func) {
+	case BTF_EVNT_RPT:
+	case BTF_EVNT_BUF_OVERFLOW:
+		pfwinfo->event[func]++;
+		/* Don't need rtw89_leave_ps_mode() */
+		btc_fw_event(rtwdev, func, buf, len);
+		break;
+	case BTF_EVNT_BT_INFO:
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], handle C2H BT INFO with data %8ph\n", buf);
+		btc->cx.cnt_bt[BTC_BCNT_INFOUPDATE]++;
+		rtw89_leave_ps_mode(rtwdev);
+		_update_bt_info(rtwdev, buf, len);
+		break;
+	case BTF_EVNT_BT_SCBD:
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], handle C2H BT SCBD with data %8ph\n", buf);
+		btc->cx.cnt_bt[BTC_BCNT_SCBDUPDATE]++;
+		rtw89_leave_ps_mode(rtwdev);
+		_update_bt_scbd(rtwdev, false);
+		break;
+	case BTF_EVNT_BT_PSD:
+		break;
+	case BTF_EVNT_BT_REG:
+		btc->dbg.rb_done = true;
+		btc->dbg.rb_val = le32_to_cpu(*((__le32 *)buf));
+
+		break;
+	case BTF_EVNT_C2H_LOOPBACK:
+		btc->dbg.rb_done = true;
+		btc->dbg.rb_val = buf[0];
+		break;
+	case BTF_EVNT_CX_RUNINFO:
+		btc->dm.cnt_dm[BTC_DCNT_CX_RUNINFO]++;
+		break;
+	}
+}
+
+#define BTC_CX_FW_OFFLOAD 0
+
+static void _show_cx_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	u32 ver_main = 0, ver_sub = 0, ver_hotfix = 0, id_branch = 0;
+
+	if (!(dm->coex_info_map & BTC_COEX_INFO_CX))
+		return;
+
+	dm->cnt_notify[BTC_NCNT_SHOW_COEX_INFO]++;
+
+	seq_printf(m, "========== [BTC COEX INFO (%d)] ==========\n",
+		   chip->chip_id);
+
+	ver_main = FIELD_GET(GENMASK(31, 24), chip->para_ver);
+	ver_sub = FIELD_GET(GENMASK(23, 16), chip->para_ver);
+	ver_hotfix = FIELD_GET(GENMASK(15, 8), chip->para_ver);
+	id_branch = FIELD_GET(GENMASK(7, 0), chip->para_ver);
+	seq_printf(m, " %-15s : Coex:%d.%d.%d(branch:%d), ",
+		   "[coex_version]", ver_main, ver_sub, ver_hotfix, id_branch);
+
+	if (dm->wl_fw_cx_offload != BTC_CX_FW_OFFLOAD)
+		dm->error.map.offload_mismatch = true;
+	else
+		dm->error.map.offload_mismatch = false;
+
+	ver_main = FIELD_GET(GENMASK(31, 24), wl->ver_info.fw_coex);
+	ver_sub = FIELD_GET(GENMASK(23, 16), wl->ver_info.fw_coex);
+	ver_hotfix = FIELD_GET(GENMASK(15, 8), wl->ver_info.fw_coex);
+	id_branch = FIELD_GET(GENMASK(7, 0), wl->ver_info.fw_coex);
+	seq_printf(m, "WL_FW_coex:%d.%d.%d(branch:%d)",
+		   ver_main, ver_sub, ver_hotfix, id_branch);
+
+	ver_main = FIELD_GET(GENMASK(31, 24), chip->wlcx_desired);
+	ver_sub = FIELD_GET(GENMASK(23, 16), chip->wlcx_desired);
+	ver_hotfix = FIELD_GET(GENMASK(15, 8), chip->wlcx_desired);
+	seq_printf(m, "(%s, desired:%d.%d.%d), ",
+		   (wl->ver_info.fw_coex >= chip->wlcx_desired ?
+		   "Match" : "Mis-Match"), ver_main, ver_sub, ver_hotfix);
+
+	seq_printf(m, "BT_FW_coex:%d(%s, desired:%d)\n",
+		   bt->ver_info.fw_coex,
+		   (bt->ver_info.fw_coex >= chip->btcx_desired ?
+		   "Match" : "Mis-Match"), chip->btcx_desired);
+
+	if (bt->enable.now && bt->ver_info.fw == 0)
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_BT_VER_INFO, true);
+	else
+		rtw89_btc_fw_en_rpt(rtwdev, RPT_EN_BT_VER_INFO, false);
+
+	ver_main = FIELD_GET(GENMASK(31, 24), wl->ver_info.fw);
+	ver_sub = FIELD_GET(GENMASK(23, 16), wl->ver_info.fw);
+	ver_hotfix = FIELD_GET(GENMASK(15, 8), wl->ver_info.fw);
+	id_branch = FIELD_GET(GENMASK(7, 0), wl->ver_info.fw);
+	seq_printf(m, " %-15s : WL_FW:%d.%d.%d.%d, BT_FW:0x%x(%s)\n",
+		   "[sub_module]",
+		   ver_main, ver_sub, ver_hotfix, id_branch,
+		   bt->ver_info.fw, bt->run_patch_code ? "patch" : "ROM");
+
+	seq_printf(m, " %-15s : cv:%x, rfe_type:0x%x, ant_iso:%d, ant_pg:%d, %s",
+		   "[hw_info]", btc->mdinfo.cv, btc->mdinfo.rfe_type,
+		   btc->mdinfo.ant.isolation, btc->mdinfo.ant.num,
+		   (btc->mdinfo.ant.num > 1 ? "" : (btc->mdinfo.ant.single_pos ?
+		   "1Ant_Pos:S1, " : "1Ant_Pos:S0, ")));
+
+	seq_printf(m, "3rd_coex:%d, dbcc:%d, tx_num:%d, rx_num:%d\n",
+		   btc->cx.other.type, rtwdev->dbcc_en, hal->tx_nss,
+		   hal->rx_nss);
+}
+
+static void _show_wl_role_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_link_info *plink = NULL;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_dbcc_info *wl_dinfo = &wl->dbcc_info;
+	struct rtw89_traffic_stats *t;
+	u8 i;
+
+	if (rtwdev->dbcc_en) {
+		seq_printf(m,
+			   " %-15s : PHY0_band(op:%d/scan:%d/real:%d), ",
+			   "[dbcc_info]", wl_dinfo->op_band[RTW89_PHY_0],
+			   wl_dinfo->scan_band[RTW89_PHY_0],
+			   wl_dinfo->real_band[RTW89_PHY_0]);
+		seq_printf(m,
+			   "PHY1_band(op:%d/scan:%d/real:%d)\n",
+			   wl_dinfo->op_band[RTW89_PHY_1],
+			   wl_dinfo->scan_band[RTW89_PHY_1],
+			   wl_dinfo->real_band[RTW89_PHY_1]);
+	}
+
+	for (i = 0; i < RTW89_MAX_HW_PORT_NUM; i++) {
+		plink = &btc->cx.wl.link_info[i];
+
+		if (!plink->active)
+			continue;
+
+		seq_printf(m,
+			   " [port_%d]        : role=%d(phy-%d), connect=%d(client_cnt=%d), mode=%d, center_ch=%d, bw=%d",
+			   plink->pid, (u32)plink->role, plink->phy,
+			   (u32)plink->connected, plink->client_cnt - 1,
+			   (u32)plink->mode, plink->ch, (u32)plink->bw);
+
+		if (plink->connected == MLME_NO_LINK)
+			continue;
+
+		seq_printf(m,
+			   ", mac_id=%d, max_tx_time=%dus, max_tx_retry=%d\n",
+			   plink->mac_id, plink->tx_time, plink->tx_retry);
+
+		seq_printf(m,
+			   " [port_%d]        : rssi=-%ddBm(%d), busy=%d, dir=%s, ",
+			   plink->pid, 110 - plink->stat.rssi,
+			   plink->stat.rssi, plink->busy,
+			   plink->dir == RTW89_TFC_UL ? "UL" : "DL");
+
+		t = &plink->stat.traffic;
+
+		seq_printf(m,
+			   "tx[rate:%d/busy_level:%d], ",
+			   (u32)t->tx_rate, t->tx_tfc_lv);
+
+		seq_printf(m, "rx[rate:%d/busy_level:%d/drop:%d]\n",
+			   (u32)t->rx_rate,
+			   t->rx_tfc_lv, plink->rx_rate_drop_cnt);
+	}
+}
+
+static void _show_wl_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_wl_role_info *wl_rinfo = &wl->role_info;
+
+	if (!(btc->dm.coex_info_map & BTC_COEX_INFO_WL))
+		return;
+
+	seq_puts(m, "========== [WL Status] ==========\n");
+
+	seq_printf(m, " %-15s : link_mode:%d, ",
+		   "[status]", (u32)wl_rinfo->link_mode);
+
+	seq_printf(m,
+		   "rf_off:%s, power_save:%s, scan:%s(band:%d/phy_map:0x%x), ",
+		   wl->status.map.rf_off ? "Y" : "N",
+		   wl->status.map.lps ? "Y" : "N",
+		   wl->status.map.scan ? "Y" : "N",
+		   wl->scan_info.band[RTW89_PHY_0], wl->scan_info.phy_map);
+
+	seq_printf(m,
+		   "connecting:%s, roam:%s, 4way:%s, init_ok:%s\n",
+		   wl->status.map.connecting ? "Y" : "N",
+		   wl->status.map.roaming ?  "Y" : "N",
+		   wl->status.map._4way ? "Y" : "N",
+		   wl->status.map.init_ok ? "Y" : "N");
+
+	_show_wl_role_info(rtwdev, m);
+}
+
+enum btc_bt_a2dp_type {
+	BTC_A2DP_LEGACY = 0,
+	BTC_A2DP_TWS_SNIFF = 1,
+	BTC_A2DP_TWS_RELAY = 2,
+};
+
+static void _show_bt_profile_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_bt_link_info *bt_linfo = &btc->cx.bt.link_info;
+	struct rtw89_btc_bt_hfp_desc hfp = bt_linfo->hfp_desc;
+	struct rtw89_btc_bt_hid_desc hid = bt_linfo->hid_desc;
+	struct rtw89_btc_bt_a2dp_desc a2dp = bt_linfo->a2dp_desc;
+	struct rtw89_btc_bt_pan_desc pan = bt_linfo->pan_desc;
+
+	if (hfp.exist) {
+		seq_printf(m, " %-15s : type:%s, sut_pwr:%d, golden-rx:%d",
+			   "[HFP]", (hfp.type == 0 ? "SCO" : "eSCO"),
+			   bt_linfo->sut_pwr_level[0],
+			   bt_linfo->golden_rx_shift[0]);
+	}
+
+	if (hid.exist) {
+		seq_printf(m,
+			   "\n\r %-15s : type:%s%s%s%s%s pair-cnt:%d, sut_pwr:%d, golden-rx:%d\n",
+			   "[HID]",
+			   hid.type & BTC_HID_218 ? "2/18," : "",
+			   hid.type & BTC_HID_418 ? "4/18," : "",
+			   hid.type & BTC_HID_BLE ? "BLE," : "",
+			   hid.type & BTC_HID_RCU ? "RCU," : "",
+			   hid.type & BTC_HID_RCU_VOICE ? "RCU-Voice," : "",
+			   hid.pair_cnt, bt_linfo->sut_pwr_level[1],
+			   bt_linfo->golden_rx_shift[1]);
+	}
+
+	if (a2dp.exist) {
+		seq_printf(m,
+			   " %-15s : type:%s, bit-pool:%d, flush-time:%d, ",
+			   "[A2DP]",
+			   a2dp.type == BTC_A2DP_LEGACY ? "Legacy" : "TWS",
+			    a2dp.bitpool, a2dp.flush_time);
+
+		seq_printf(m,
+			   "vid:0x%x, Dev-name:0x%x, sut_pwr:%d, golden-rx:%d\n",
+			   a2dp.vendor_id, a2dp.device_name,
+			   bt_linfo->sut_pwr_level[2],
+			   bt_linfo->golden_rx_shift[2]);
+	}
+
+	if (pan.exist) {
+		seq_printf(m, " %-15s : sut_pwr:%d, golden-rx:%d\n",
+			   "[PAN]",
+			   bt_linfo->sut_pwr_level[3],
+			   bt_linfo->golden_rx_shift[3]);
+	}
+}
+
+static void _show_bt_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_module *module = &btc->mdinfo;
+	struct rtw89_btc_bt_link_info *bt_linfo = &bt->link_info;
+	u8 *afh = bt_linfo->afh_map;
+	u16 polt_cnt = 0;
+
+	if (!(btc->dm.coex_info_map & BTC_COEX_INFO_BT))
+		return;
+
+	seq_puts(m, "========== [BT Status] ==========\n");
+
+	seq_printf(m, " %-15s : enable:%s, btg:%s%s, connect:%s, ",
+		   "[status]", bt->enable.now ? "Y" : "N",
+		   bt->btg_type ? "Y" : "N",
+		   (bt->enable.now && (bt->btg_type != module->bt_pos) ?
+		   "(efuse-mismatch!!)" : ""),
+		   (bt_linfo->status.map.connect ? "Y" : "N"));
+
+	seq_printf(m, "igno_wl:%s, mailbox_avl:%s, rfk_state:0x%x\n",
+		   bt->igno_wl ? "Y" : "N",
+		   bt->mbx_avl ? "Y" : "N", bt->rfk_info.val);
+
+	seq_printf(m, " %-15s : profile:%s%s%s%s%s ",
+		   "[profile]",
+		   (bt_linfo->profile_cnt.now == 0) ? "None," : "",
+		   bt_linfo->hfp_desc.exist ? "HFP," : "",
+		   bt_linfo->hid_desc.exist ? "HID," : "",
+		   bt_linfo->a2dp_desc.exist ?
+		   (bt_linfo->a2dp_desc.sink ? "A2DP_sink," : "A2DP,") : "",
+		   bt_linfo->pan_desc.exist ? "PAN," : "");
+
+	seq_printf(m,
+		   "multi-link:%s, role:%s, ble-connect:%s, CQDDR:%s, A2DP_active:%s, PAN_active:%s\n",
+		   bt_linfo->multi_link.now ? "Y" : "N",
+		   bt_linfo->slave_role ? "Slave" : "Master",
+		   bt_linfo->status.map.ble_connect ? "Y" : "N",
+		   bt_linfo->cqddr ? "Y" : "N",
+		   bt_linfo->a2dp_desc.active ? "Y" : "N",
+		   bt_linfo->pan_desc.active ? "Y" : "N");
+
+	seq_printf(m,
+		   " %-15s : rssi:%ddBm, tx_rate:%dM, %s%s%s",
+		   "[link]", bt_linfo->rssi - 100,
+		   bt_linfo->tx_3m ? 3 : 2,
+		   bt_linfo->status.map.inq_pag ? " inq-page!!" : "",
+		   bt_linfo->status.map.acl_busy ? " acl_busy!!" : "",
+		   bt_linfo->status.map.mesh_busy ? " mesh_busy!!" : "");
+
+	seq_printf(m,
+		   "%s afh_map[%02x%02x_%02x%02x_%02x%02x_%02x%02x_%02x%02x], ",
+		   bt_linfo->relink.now ? " ReLink!!" : "",
+		   afh[0], afh[1], afh[2], afh[3], afh[4],
+		   afh[5], afh[6], afh[7], afh[8], afh[9]);
+
+	seq_printf(m, "wl_ch_map[en:%d/ch:%d/bw:%d]\n",
+		   wl->afh_info.en, wl->afh_info.ch, wl->afh_info.bw);
+
+	seq_printf(m,
+		   " %-15s : retry:%d, relink:%d, rate_chg:%d, reinit:%d, reenable:%d, ",
+		   "[stat_cnt]", cx->cnt_bt[BTC_BCNT_RETRY],
+		   cx->cnt_bt[BTC_BCNT_RELINK], cx->cnt_bt[BTC_BCNT_RATECHG],
+		   cx->cnt_bt[BTC_BCNT_REINIT], cx->cnt_bt[BTC_BCNT_REENABLE]);
+
+	seq_printf(m,
+		   "role-switch:%d, afh:%d, inq_page:%d(inq:%d/page:%d), igno_wl:%d\n",
+		   cx->cnt_bt[BTC_BCNT_ROLESW], cx->cnt_bt[BTC_BCNT_AFH],
+		   cx->cnt_bt[BTC_BCNT_INQPAG], cx->cnt_bt[BTC_BCNT_INQ],
+		   cx->cnt_bt[BTC_BCNT_PAGE], cx->cnt_bt[BTC_BCNT_IGNOWL]);
+
+	_show_bt_profile_info(rtwdev, m);
+
+	seq_printf(m,
+		   " %-15s : raw_data[%02x %02x %02x %02x %02x %02x] (type:%s/cnt:%d/same:%d)\n",
+		   "[bt_info]", bt->raw_info[2], bt->raw_info[3],
+		   bt->raw_info[4], bt->raw_info[5], bt->raw_info[6],
+		   bt->raw_info[7],
+		   bt->raw_info[0] == BTC_BTINFO_AUTO ? "auto" : "reply",
+		   cx->cnt_bt[BTC_BCNT_INFOUPDATE],
+		   cx->cnt_bt[BTC_BCNT_INFOSAME]);
+
+	if (wl->status.map.lps || wl->status.map.rf_off)
+		return;
+
+	chip->ops->btc_update_bt_cnt(rtwdev);
+	_chk_btc_err(rtwdev, BTC_DCNT_BTCNT_FREEZE, 0);
+
+	seq_printf(m,
+		   " %-15s : Hi-rx = %d, Hi-tx = %d, Lo-rx = %d, Lo-tx = %d (bt_polut_wl_tx = %d)\n",
+		   "[trx_req_cnt]", cx->cnt_bt[BTC_BCNT_HIPRI_RX],
+		   cx->cnt_bt[BTC_BCNT_HIPRI_TX], cx->cnt_bt[BTC_BCNT_LOPRI_RX],
+		   cx->cnt_bt[BTC_BCNT_LOPRI_TX], polt_cnt);
+}
+
+#define CASE_BTC_RSN_STR(e) case BTC_RSN_ ## e: return #e
+#define CASE_BTC_ACT_STR(e) case BTC_ACT_ ## e | BTC_ACT_EXT_BIT: return #e
+#define CASE_BTC_POLICY_STR(e) \
+	case BTC_CXP_ ## e | BTC_POLICY_EXT_BIT: return #e
+
+static const char *steps_to_str(u16 step)
+{
+	switch (step) {
+	CASE_BTC_RSN_STR(NONE);
+	CASE_BTC_RSN_STR(NTFY_INIT);
+	CASE_BTC_RSN_STR(NTFY_SWBAND);
+	CASE_BTC_RSN_STR(NTFY_WL_STA);
+	CASE_BTC_RSN_STR(NTFY_RADIO_STATE);
+	CASE_BTC_RSN_STR(UPDATE_BT_SCBD);
+	CASE_BTC_RSN_STR(NTFY_WL_RFK);
+	CASE_BTC_RSN_STR(UPDATE_BT_INFO);
+	CASE_BTC_RSN_STR(NTFY_SCAN_START);
+	CASE_BTC_RSN_STR(NTFY_SCAN_FINISH);
+	CASE_BTC_RSN_STR(NTFY_SPECIFIC_PACKET);
+	CASE_BTC_RSN_STR(NTFY_POWEROFF);
+	CASE_BTC_RSN_STR(NTFY_ROLE_INFO);
+	CASE_BTC_RSN_STR(CMD_SET_COEX);
+	CASE_BTC_RSN_STR(ACT1_WORK);
+	CASE_BTC_RSN_STR(BT_DEVINFO_WORK);
+	CASE_BTC_RSN_STR(RFK_CHK_WORK);
+
+	CASE_BTC_ACT_STR(NONE);
+	CASE_BTC_ACT_STR(WL_ONLY);
+	CASE_BTC_ACT_STR(WL_5G);
+	CASE_BTC_ACT_STR(WL_OTHER);
+	CASE_BTC_ACT_STR(WL_IDLE);
+	CASE_BTC_ACT_STR(WL_NC);
+	CASE_BTC_ACT_STR(WL_RFK);
+	CASE_BTC_ACT_STR(WL_INIT);
+	CASE_BTC_ACT_STR(WL_OFF);
+	CASE_BTC_ACT_STR(FREERUN);
+	CASE_BTC_ACT_STR(BT_WHQL);
+	CASE_BTC_ACT_STR(BT_RFK);
+	CASE_BTC_ACT_STR(BT_OFF);
+	CASE_BTC_ACT_STR(BT_IDLE);
+	CASE_BTC_ACT_STR(BT_HFP);
+	CASE_BTC_ACT_STR(BT_HID);
+	CASE_BTC_ACT_STR(BT_A2DP);
+	CASE_BTC_ACT_STR(BT_A2DPSINK);
+	CASE_BTC_ACT_STR(BT_PAN);
+	CASE_BTC_ACT_STR(BT_A2DP_HID);
+	CASE_BTC_ACT_STR(BT_A2DP_PAN);
+	CASE_BTC_ACT_STR(BT_PAN_HID);
+	CASE_BTC_ACT_STR(BT_A2DP_PAN_HID);
+	CASE_BTC_ACT_STR(WL_25G_MCC);
+	CASE_BTC_ACT_STR(WL_2G_MCC);
+	CASE_BTC_ACT_STR(WL_2G_SCC);
+	CASE_BTC_ACT_STR(WL_2G_AP);
+	CASE_BTC_ACT_STR(WL_2G_GO);
+	CASE_BTC_ACT_STR(WL_2G_GC);
+	CASE_BTC_ACT_STR(WL_2G_NAN);
+
+	CASE_BTC_POLICY_STR(OFF_BT);
+	CASE_BTC_POLICY_STR(OFF_WL);
+	CASE_BTC_POLICY_STR(OFF_EQ0);
+	CASE_BTC_POLICY_STR(OFF_EQ1);
+	CASE_BTC_POLICY_STR(OFF_EQ2);
+	CASE_BTC_POLICY_STR(OFF_EQ3);
+	CASE_BTC_POLICY_STR(OFF_BWB0);
+	CASE_BTC_POLICY_STR(OFF_BWB1);
+	CASE_BTC_POLICY_STR(OFFB_BWB0);
+	CASE_BTC_POLICY_STR(OFFE_DEF);
+	CASE_BTC_POLICY_STR(OFFE_DEF2);
+	CASE_BTC_POLICY_STR(FIX_TD3030);
+	CASE_BTC_POLICY_STR(FIX_TD5050);
+	CASE_BTC_POLICY_STR(FIX_TD2030);
+	CASE_BTC_POLICY_STR(FIX_TD4010);
+	CASE_BTC_POLICY_STR(FIX_TD7010);
+	CASE_BTC_POLICY_STR(FIX_TD2060);
+	CASE_BTC_POLICY_STR(FIX_TD3060);
+	CASE_BTC_POLICY_STR(FIX_TD2080);
+	CASE_BTC_POLICY_STR(FIX_TDW1B1);
+	CASE_BTC_POLICY_STR(FIX_TD4020);
+	CASE_BTC_POLICY_STR(PFIX_TD3030);
+	CASE_BTC_POLICY_STR(PFIX_TD5050);
+	CASE_BTC_POLICY_STR(PFIX_TD2030);
+	CASE_BTC_POLICY_STR(PFIX_TD2060);
+	CASE_BTC_POLICY_STR(PFIX_TD3070);
+	CASE_BTC_POLICY_STR(PFIX_TD2080);
+	CASE_BTC_POLICY_STR(PFIX_TDW1B1);
+	CASE_BTC_POLICY_STR(AUTO_TD50200);
+	CASE_BTC_POLICY_STR(AUTO_TD60200);
+	CASE_BTC_POLICY_STR(AUTO_TD20200);
+	CASE_BTC_POLICY_STR(AUTO_TDW1B1);
+	CASE_BTC_POLICY_STR(PAUTO_TD50200);
+	CASE_BTC_POLICY_STR(PAUTO_TD60200);
+	CASE_BTC_POLICY_STR(PAUTO_TD20200);
+	CASE_BTC_POLICY_STR(PAUTO_TDW1B1);
+	CASE_BTC_POLICY_STR(AUTO2_TD3050);
+	CASE_BTC_POLICY_STR(AUTO2_TD3070);
+	CASE_BTC_POLICY_STR(AUTO2_TD5050);
+	CASE_BTC_POLICY_STR(AUTO2_TD6060);
+	CASE_BTC_POLICY_STR(AUTO2_TD2080);
+	CASE_BTC_POLICY_STR(AUTO2_TDW1B4);
+	CASE_BTC_POLICY_STR(PAUTO2_TD3050);
+	CASE_BTC_POLICY_STR(PAUTO2_TD3070);
+	CASE_BTC_POLICY_STR(PAUTO2_TD5050);
+	CASE_BTC_POLICY_STR(PAUTO2_TD6060);
+	CASE_BTC_POLICY_STR(PAUTO2_TD2080);
+	CASE_BTC_POLICY_STR(PAUTO2_TDW1B4);
+	default:
+		return "unknown step";
+	}
+}
+
+static
+void seq_print_segment(struct seq_file *m, const char *prefix, u16 *data,
+		       u8 len, u8 seg_len, u8 start_idx, u8 ring_len)
+{
+	u8 i;
+	u8 cur_index;
+
+	for (i = 0; i < len ; i++) {
+		if ((i % seg_len) == 0)
+			seq_printf(m, " %-15s : ", prefix);
+		cur_index = (start_idx + i) % ring_len;
+		if (i % 3 == 0)
+			seq_printf(m, "-> %-20s",
+				   steps_to_str(*(data + cur_index)));
+		else if (i % 3 == 1)
+			seq_printf(m, "-> %-15s",
+				   steps_to_str(*(data + cur_index)));
+		else
+			seq_printf(m, "-> %-13s",
+				   steps_to_str(*(data + cur_index)));
+		if (i == (len - 1) || (i % seg_len) == (seg_len - 1))
+			seq_puts(m, "\n");
+	}
+}
+
+static void _show_dm_step(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	u8 start_idx;
+	u8 len;
+
+	len = dm->dm_step.step_ov ? RTW89_BTC_DM_MAXSTEP : dm->dm_step.step_pos;
+	start_idx = dm->dm_step.step_ov ? dm->dm_step.step_pos : 0;
+
+	seq_print_segment(m, "[dm_steps]", dm->dm_step.step, len, 6, start_idx,
+			  ARRAY_SIZE(dm->dm_step.step));
+}
+
+static void _show_dm_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_module *module = &btc->mdinfo;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+
+	if (!(dm->coex_info_map & BTC_COEX_INFO_DM))
+		return;
+
+	seq_printf(m, "========== [Mechanism Status %s] ==========\n",
+		   (btc->ctrl.manual ? "(Manual)" : "(Auto)"));
+
+	seq_printf(m,
+		   " %-15s : type:%s, reason:%s(), action:%s(), ant_path:%ld, run_cnt:%d\n",
+		   "[status]",
+		   module->ant.type == BTC_ANT_SHARED ? "shared" : "dedicated",
+		   steps_to_str(dm->run_reason),
+		   steps_to_str(dm->run_action | BTC_ACT_EXT_BIT),
+		   FIELD_GET(GENMASK(7, 0), dm->set_ant_path),
+		   dm->cnt_dm[BTC_DCNT_RUN]);
+
+	_show_dm_step(rtwdev, m);
+
+	seq_printf(m, " %-15s : wl_only:%d, bt_only:%d, igno_bt:%d, free_run:%d, wl_ps_ctrl:%d, wl_mimo_ps:%d, ",
+		   "[dm_flag]", dm->wl_only, dm->bt_only, btc->ctrl.igno_bt,
+		   dm->freerun, btc->lps, dm->wl_mimo_ps);
+
+	seq_printf(m, "leak_ap:%d, fw_offload:%s%s\n", dm->leak_ap,
+		   (BTC_CX_FW_OFFLOAD ? "Y" : "N"),
+		   (dm->wl_fw_cx_offload == BTC_CX_FW_OFFLOAD ?
+		    "" : "(Mis-Match!!)"));
+
+	if (dm->rf_trx_para.wl_tx_power == 0xff)
+		seq_printf(m,
+			   " %-15s : wl_rssi_lvl:%d, para_lvl:%d, wl_tx_pwr:orig, ",
+			   "[trx_ctrl]", wl->rssi_level, dm->trx_para_level);
+
+	else
+		seq_printf(m,
+			   " %-15s : wl_rssi_lvl:%d, para_lvl:%d, wl_tx_pwr:%d, ",
+			   "[trx_ctrl]", wl->rssi_level, dm->trx_para_level,
+			   dm->rf_trx_para.wl_tx_power);
+
+	seq_printf(m,
+		   "wl_rx_lvl:%d, bt_tx_pwr_dec:%d, bt_rx_lna:%d(%s-tbl), wl_btg_rx:%d\n",
+		   dm->rf_trx_para.wl_rx_gain, dm->rf_trx_para.bt_tx_power,
+		   dm->rf_trx_para.bt_rx_gain,
+		   (bt->hi_lna_rx ? "Hi" : "Ori"), dm->wl_btg_rx);
+
+	seq_printf(m,
+		   " %-15s : wl_tx_limit[en:%d/max_t:%dus/max_retry:%d], bt_slot_reg:%d-TU\n",
+		   "[dm_ctrl]", dm->wl_tx_limit.enable, dm->wl_tx_limit.tx_time,
+		   dm->wl_tx_limit.tx_retry, btc->bt_req_len);
+}
+
+static void _show_error(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_fbtc_cysta *pcysta = NULL;
+
+	pcysta = &pfwinfo->rpt_fbtc_cysta.finfo;
+
+	if (pfwinfo->event[BTF_EVNT_BUF_OVERFLOW] == 0 &&
+	    pcysta->except_cnt == 0 &&
+	    !pfwinfo->len_mismch && !pfwinfo->fver_mismch)
+		return;
+
+	seq_printf(m, " %-15s : ", "[error]");
+
+	if (pfwinfo->event[BTF_EVNT_BUF_OVERFLOW]) {
+		seq_printf(m,
+			   "overflow-cnt: %d, ",
+			   pfwinfo->event[BTF_EVNT_BUF_OVERFLOW]);
+	}
+
+	if (pfwinfo->len_mismch) {
+		seq_printf(m,
+			   "len-mismatch: 0x%x, ",
+			   pfwinfo->len_mismch);
+	}
+
+	if (pfwinfo->fver_mismch) {
+		seq_printf(m,
+			   "fver-mismatch: 0x%x, ",
+			   pfwinfo->fver_mismch);
+	}
+
+	/* cycle statistics exceptions */
+	if (pcysta->exception || pcysta->except_cnt) {
+		seq_printf(m,
+			   "exception-type: 0x%x, exception-cnt = %d",
+			   pcysta->exception, pcysta->except_cnt);
+	}
+	seq_puts(m, "\n");
+}
+
+static void _show_fbtc_tdma(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_tdma *t = NULL;
+	struct rtw89_btc_fbtc_slot *s = NULL;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	u8 i, cnt = 0;
+
+	pcinfo = &pfwinfo->rpt_fbtc_tdma.cinfo;
+	if (!pcinfo->valid)
+		return;
+
+	t = &pfwinfo->rpt_fbtc_tdma.finfo;
+
+	seq_printf(m,
+		   " %-15s : ", "[tdma_policy]");
+	seq_printf(m,
+		   "type:%d, rx_flow_ctrl:%d, tx_pause:%d, ",
+		   (u32)t->type,
+		   t->rxflctrl, t->txpause);
+
+	seq_printf(m,
+		   "wl_toggle_n:%d, leak_n:%d, ext_ctrl:%d, ",
+		   t->wtgle_n, t->leak_n, t->ext_ctrl);
+
+	seq_printf(m,
+		   "policy_type:%d",
+		   (u32)btc->policy_type);
+
+	s = pfwinfo->rpt_fbtc_slots.finfo.slot;
+
+	for (i = 0; i < CXST_MAX; i++) {
+		if (dm->update_slot_map == BIT(CXST_MAX) - 1)
+			break;
+
+		if (!(dm->update_slot_map & BIT(i)))
+			continue;
+
+		if (cnt % 6 == 0)
+			seq_printf(m,
+				   " %-15s : %d[%d/0x%x/%d]",
+				   "[slot_policy]",
+				   (u32)i,
+				   s[i].dur, s[i].cxtbl, s[i].cxtype);
+		else
+			seq_printf(m,
+				   ", %d[%d/0x%x/%d]",
+				   (u32)i,
+				   s[i].dur, s[i].cxtbl, s[i].cxtype);
+		if (cnt % 6 == 5)
+			seq_puts(m, "\n");
+		cnt++;
+	}
+	seq_puts(m, "\n");
+}
+
+static void _show_fbtc_slots(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_slots *pslots = NULL;
+	struct rtw89_btc_fbtc_slot s;
+	u8 i = 0;
+
+	pcinfo = &pfwinfo->rpt_fbtc_slots.cinfo;
+	if (!pcinfo->valid)
+		return;
+
+	pslots = &pfwinfo->rpt_fbtc_slots.finfo;
+
+	for (i = 0; i < CXST_MAX; i++) {
+		s = pslots->slot[i];
+		if (i % 6 == 0)
+			seq_printf(m,
+				   " %-15s : %02d[%03d/0x%x/%d]",
+				   "[slot_list]",
+				   (u32)i,
+				   s.dur, s.cxtbl, s.cxtype);
+		else
+			seq_printf(m,
+				   ", %02d[%03d/0x%x/%d]",
+				   (u32)i,
+				   s.dur, s.cxtbl, s.cxtype);
+		if (i % 6 == 5)
+			seq_puts(m, "\n");
+	}
+}
+
+static void _show_fbtc_cysta(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_bt_a2dp_desc *a2dp = &btc->cx.bt.link_info.a2dp_desc;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_cysta *pcysta_le32 = NULL;
+	struct rtw89_btc_fbtc_cysta_cpu pcysta[1];
+	union rtw89_btc_fbtc_rxflct r;
+	u8 i, cnt = 0, slot_pair;
+	u16 cycle, c_begin, c_end, store_index;
+
+	pcinfo = &pfwinfo->rpt_fbtc_cysta.cinfo;
+	if (!pcinfo->valid)
+		return;
+
+	pcysta_le32 = &pfwinfo->rpt_fbtc_cysta.finfo;
+	rtw89_btc_fbtc_cysta_to_cpu(pcysta_le32, pcysta);
+	seq_printf(m,
+		   " %-15s : cycle:%d, bcn[all:%d/all_ok:%d/bt:%d/bt_ok:%d]",
+		   "[cycle_cnt]", pcysta->cycles, pcysta->bcn_cnt[CXBCN_ALL],
+		   pcysta->bcn_cnt[CXBCN_ALL_OK],
+		   pcysta->bcn_cnt[CXBCN_BT_SLOT],
+		   pcysta->bcn_cnt[CXBCN_BT_OK]);
+
+	_chk_btc_err(rtwdev, BTC_DCNT_CYCLE_FREEZE, (u32)pcysta->cycles);
+
+	for (i = 0; i < CXST_MAX; i++) {
+		if (!pcysta->slot_cnt[i])
+			continue;
+		seq_printf(m,
+			   ", %d:%d", (u32)i, pcysta->slot_cnt[i]);
+	}
+
+	if (dm->tdma_now.rxflctrl) {
+		seq_printf(m,
+			   ", leak_rx:%d", pcysta->leakrx_cnt);
+	}
+
+	if (pcysta->collision_cnt) {
+		seq_printf(m,
+			   ", collision:%d", pcysta->collision_cnt);
+	}
+
+	if (pcysta->skip_cnt) {
+		seq_printf(m,
+			   ", skip:%d", pcysta->skip_cnt);
+	}
+	seq_puts(m, "\n");
+
+	_chk_btc_err(rtwdev, BTC_DCNT_W1_FREEZE, pcysta->slot_cnt[CXST_W1]);
+	_chk_btc_err(rtwdev, BTC_DCNT_B1_FREEZE, pcysta->slot_cnt[CXST_B1]);
+
+	seq_printf(m, " %-15s : avg_t[wl:%d/bt:%d/lk:%d.%03d]",
+		   "[cycle_time]",
+		   pcysta->tavg_cycle[CXT_WL],
+		   pcysta->tavg_cycle[CXT_BT],
+		   pcysta->tavg_lk / 1000, pcysta->tavg_lk % 1000);
+	seq_printf(m,
+		   ", max_t[wl:%d/bt:%d/lk:%d.%03d]",
+		   pcysta->tmax_cycle[CXT_WL],
+		   pcysta->tmax_cycle[CXT_BT],
+		   pcysta->tmax_lk / 1000, pcysta->tmax_lk % 1000);
+	seq_printf(m,
+		   ", maxdiff_t[wl:%d/bt:%d]\n",
+		   pcysta->tmaxdiff_cycle[CXT_WL],
+		   pcysta->tmaxdiff_cycle[CXT_BT]);
+
+	if (pcysta->cycles == 0)
+		return;
+
+	/* 1 cycle record 1 wl-slot and 1 bt-slot */
+	slot_pair = BTC_CYCLE_SLOT_MAX / 2;
+
+	if (pcysta->cycles <= slot_pair)
+		c_begin = 1;
+	else
+		c_begin = pcysta->cycles - slot_pair + 1;
+
+	c_end = pcysta->cycles;
+
+	for (cycle = c_begin; cycle <= c_end; cycle++) {
+		cnt++;
+		store_index = ((cycle - 1) % slot_pair) * 2;
+
+		if (cnt % (BTC_CYCLE_SLOT_MAX / 4) == 1)
+			seq_printf(m,
+				   " %-15s : ->b%02d->w%02d", "[cycle_step]",
+				   pcysta->tslot_cycle[store_index],
+				   pcysta->tslot_cycle[store_index + 1]);
+		else
+			seq_printf(m,
+				   "->b%02d->w%02d",
+				   pcysta->tslot_cycle[store_index],
+				   pcysta->tslot_cycle[store_index + 1]);
+		if (cnt % (BTC_CYCLE_SLOT_MAX / 4) == 0 || cnt == c_end)
+			seq_puts(m, "\n");
+	}
+
+	if (a2dp->exist) {
+		seq_printf(m,
+			   " %-15s : a2dp_ept:%d, a2dp_late:%d",
+			   "[a2dp_t_sta]",
+			   pcysta->a2dpept, pcysta->a2dpeptto);
+
+		seq_printf(m,
+			   ", avg_t:%d, max_t:%d",
+			   pcysta->tavg_a2dpept, pcysta->tmax_a2dpept);
+		r.val = dm->tdma_now.rxflctrl;
+
+		if (r.type && r.tgln_n) {
+			seq_printf(m,
+				   ", cycle[PSTDMA:%d/TDMA:%d], ",
+				   pcysta->cycles_a2dp[CXT_FLCTRL_ON],
+				   pcysta->cycles_a2dp[CXT_FLCTRL_OFF]);
+
+			seq_printf(m,
+				   "avg_t[PSTDMA:%d/TDMA:%d], ",
+				   pcysta->tavg_a2dp[CXT_FLCTRL_ON],
+				   pcysta->tavg_a2dp[CXT_FLCTRL_OFF]);
+
+			seq_printf(m,
+				   "max_t[PSTDMA:%d/TDMA:%d]",
+				   pcysta->tmax_a2dp[CXT_FLCTRL_ON],
+				   pcysta->tmax_a2dp[CXT_FLCTRL_OFF]);
+		}
+		seq_puts(m, "\n");
+	}
+}
+
+static void _show_fbtc_nullsta(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_cynullsta *ns = NULL;
+	u8 i = 0;
+
+	if (!btc->dm.tdma_now.rxflctrl)
+		return;
+
+	pcinfo = &pfwinfo->rpt_fbtc_nullsta.cinfo;
+	if (!pcinfo->valid)
+		return;
+
+	ns = &pfwinfo->rpt_fbtc_nullsta.finfo;
+
+	seq_printf(m, " %-15s : ", "[null_sta]");
+
+	for (i = 0; i < 2; i++) {
+		if (i != 0)
+			seq_printf(m, ", null-%d", i);
+		else
+			seq_printf(m, "null-%d", i);
+		seq_printf(m, "[ok:%d/", le32_to_cpu(ns->result[i][1]));
+		seq_printf(m, "fail:%d/", le32_to_cpu(ns->result[i][0]));
+		seq_printf(m, "on_time:%d/", le32_to_cpu(ns->result[i][2]));
+		seq_printf(m, "retry:%d/", le32_to_cpu(ns->result[i][3]));
+		seq_printf(m, "avg_t:%d.%03d/",
+			   le32_to_cpu(ns->avg_t[i]) / 1000,
+			   le32_to_cpu(ns->avg_t[i]) % 1000);
+		seq_printf(m, "max_t:%d.%03d]",
+			   le32_to_cpu(ns->max_t[i]) / 1000,
+			   le32_to_cpu(ns->max_t[i]) % 1000);
+	}
+	seq_puts(m, "\n");
+}
+
+static void _show_fbtc_step(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_steps *pstep = NULL;
+	u8 type, val, cnt = 0, state = 0;
+	bool outloop = false;
+	u16 i, diff_t, n_start = 0, n_stop = 0;
+	u16 pos_old, pos_new;
+
+	pcinfo = &pfwinfo->rpt_fbtc_step.cinfo;
+	if (!pcinfo->valid)
+		return;
+
+	pstep = &pfwinfo->rpt_fbtc_step.finfo;
+	pos_old = le16_to_cpu(pstep->pos_old);
+	pos_new = le16_to_cpu(pstep->pos_new);
+
+	if (pcinfo->req_fver != pstep->fver)
+		return;
+
+	/* store step info by using ring instead of FIFO*/
+	do {
+		switch (state) {
+		case 0:
+			n_start = pos_old;
+			if (pos_new >=  pos_old)
+				n_stop = pos_new;
+			else
+				n_stop = btc->ctrl.trace_step - 1;
+
+			state = 1;
+			break;
+		case 1:
+			for (i = n_start; i <= n_stop; i++) {
+				type = pstep->step[i].type;
+				val = pstep->step[i].val;
+				diff_t = le16_to_cpu(pstep->step[i].difft);
+
+				if (type == CXSTEP_NONE || type >= CXSTEP_MAX)
+					continue;
+
+				if (cnt % 10 == 0)
+					seq_printf(m, " %-15s : ", "[steps]");
+
+				seq_printf(m, "-> %s(%02d)(%02d)",
+					   (type == CXSTEP_SLOT ? "SLT" :
+					    "EVT"), (u32)val, diff_t);
+				if (cnt % 10 == 9)
+					seq_puts(m, "\n");
+				cnt++;
+			}
+
+			state = 2;
+			break;
+		case 2:
+			if (pos_new <  pos_old && n_start != 0) {
+				n_start = 0;
+				n_stop = pos_new;
+				state = 1;
+			} else {
+				outloop = true;
+			}
+			break;
+		}
+	} while (!outloop);
+}
+
+static void _show_fw_dm_msg(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	if (!(btc->dm.coex_info_map & BTC_COEX_INFO_DM))
+		return;
+
+	_show_error(rtwdev, m);
+	_show_fbtc_tdma(rtwdev, m);
+	_show_fbtc_slots(rtwdev, m);
+	_show_fbtc_cysta(rtwdev, m);
+	_show_fbtc_nullsta(rtwdev, m);
+	_show_fbtc_step(rtwdev, m);
+}
+
+static void _show_mreg(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_mreg_val *pmreg = NULL;
+	struct rtw89_btc_fbtc_gpio_dbg *gdbg = NULL;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_mac_ax_gnt gnt[2] = {0};
+	u8 i = 0, type = 0, cnt = 0;
+	u32 val, offset;
+
+	if (!(btc->dm.coex_info_map & BTC_COEX_INFO_MREG))
+		return;
+
+	seq_puts(m, "========== [HW Status] ==========\n");
+
+	seq_printf(m,
+		   " %-15s : WL->BT:0x%08x(cnt:%d), BT->WL:0x%08x(total:%d, bt_update:%d)\n",
+		   "[scoreboard]", wl->scbd, cx->cnt_wl[BTC_WCNT_SCBDUPDATE],
+		   bt->scbd, cx->cnt_bt[BTC_BCNT_SCBDREAD],
+		   cx->cnt_bt[BTC_BCNT_SCBDUPDATE]);
+
+	/* To avoid I/O if WL LPS or power-off  */
+	if (!wl->status.map.lps && !wl->status.map.rf_off) {
+		rtw89_mac_read_lte(rtwdev, R_AX_LTE_SW_CFG_1, &val);
+		if (val & (B_AX_GNT_BT_RFC_S0_SW_VAL |
+		    B_AX_GNT_BT_BB_S0_SW_VAL))
+			gnt[0].gnt_bt = true;
+		if (val & (B_AX_GNT_BT_RFC_S0_SW_CTRL |
+		    B_AX_GNT_BT_BB_S0_SW_CTRL))
+			gnt[0].gnt_bt_sw_en = true;
+		if (val & (B_AX_GNT_WL_RFC_S0_SW_VAL |
+		    B_AX_GNT_WL_BB_S0_SW_VAL))
+			gnt[0].gnt_wl = true;
+		if (val & (B_AX_GNT_WL_RFC_S0_SW_CTRL |
+		    B_AX_GNT_WL_BB_S0_SW_CTRL))
+			gnt[0].gnt_wl_sw_en = true;
+
+		if (val & (B_AX_GNT_BT_RFC_S1_SW_VAL |
+		    B_AX_GNT_BT_BB_S1_SW_VAL))
+			gnt[1].gnt_bt = true;
+		if (val & (B_AX_GNT_BT_RFC_S1_SW_CTRL |
+		    B_AX_GNT_BT_BB_S1_SW_CTRL))
+			gnt[1].gnt_bt_sw_en = true;
+		if (val & (B_AX_GNT_WL_RFC_S1_SW_VAL |
+		    B_AX_GNT_WL_BB_S1_SW_VAL))
+			gnt[1].gnt_wl = true;
+		if (val & (B_AX_GNT_WL_RFC_S1_SW_CTRL |
+		    B_AX_GNT_WL_BB_S1_SW_CTRL))
+			gnt[1].gnt_wl_sw_en = true;
+
+		seq_printf(m,
+			   " %-15s : pta_owner:%s, phy-0[gnt_wl:%s-%d/gnt_bt:%s-%d], ",
+			   "[gnt_status]",
+			   (rtw89_mac_get_ctrl_path(rtwdev) ? "WL" : "BT"),
+			   (gnt[0].gnt_wl_sw_en ? "SW" : "HW"), gnt[0].gnt_wl,
+			   (gnt[0].gnt_bt_sw_en ? "SW" : "HW"), gnt[0].gnt_bt);
+
+		seq_printf(m, "phy-1[gnt_wl:%s-%d/gnt_bt:%s-%d]\n",
+			   (gnt[1].gnt_wl_sw_en ? "SW" : "HW"), gnt[1].gnt_wl,
+			   (gnt[1].gnt_bt_sw_en ? "SW" : "HW"), gnt[1].gnt_bt);
+	}
+
+	pcinfo = &pfwinfo->rpt_fbtc_mregval.cinfo;
+	if (!pcinfo->valid) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): stop due rpt_fbtc_mregval.cinfo\n",
+			    __func__);
+		return;
+	}
+
+	pmreg = &pfwinfo->rpt_fbtc_mregval.finfo;
+	rtw89_debug(rtwdev, RTW89_DBG_BTC,
+		    "[BTC], %s(): rpt_fbtc_mregval reg_num = %d\n",
+		    __func__, pmreg->reg_num);
+
+	for (i = 0; i < pmreg->reg_num; i++) {
+		type = (u8)le16_to_cpu(chip->mon_reg[i].type);
+		offset = le32_to_cpu(chip->mon_reg[i].offset);
+		val = le32_to_cpu(pmreg->mreg_val[i]);
+
+		if (cnt % 6 == 0)
+			seq_printf(m, " %-15s : %d_0x%04x=0x%08x",
+				   "[reg]", (u32)type, offset, val);
+		else
+			seq_printf(m, ", %d_0x%04x=0x%08x", (u32)type,
+				   offset, val);
+		if (cnt % 6 == 5)
+			seq_puts(m, "\n");
+		cnt++;
+	}
+
+	pcinfo = &pfwinfo->rpt_fbtc_gpio_dbg.cinfo;
+	if (!pcinfo->valid) {
+		rtw89_debug(rtwdev, RTW89_DBG_BTC,
+			    "[BTC], %s(): stop due rpt_fbtc_gpio_dbg.cinfo\n",
+			    __func__);
+		return;
+	}
+
+	gdbg = &pfwinfo->rpt_fbtc_gpio_dbg.finfo;
+	if (!gdbg->en_map)
+		return;
+
+	seq_printf(m, " %-15s : enable_map:0x%08x",
+		   "[gpio_dbg]", gdbg->en_map);
+
+	for (i = 0; i < BTC_DBG_MAX1; i++) {
+		if (!(gdbg->en_map & BIT(i)))
+			continue;
+		seq_printf(m, ", %d->GPIO%d", (u32)i, gdbg->gpio_map[i]);
+	}
+	seq_puts(m, "\n");
+}
+
+static void _show_summary(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_btf_fwinfo *pfwinfo = &btc->fwinfo;
+	struct rtw89_btc_rpt_cmn_info *pcinfo = NULL;
+	struct rtw89_btc_fbtc_rpt_ctrl *prptctrl = NULL;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_wl_info *wl = &cx->wl;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+	u32 cnt_sum = 0, *cnt = btc->dm.cnt_notify;
+	u8 i;
+
+	if (!(dm->coex_info_map & BTC_COEX_INFO_SUMMARY))
+		return;
+
+	seq_puts(m, "========== [Statistics] ==========\n");
+
+	pcinfo = &pfwinfo->rpt_ctrl.cinfo;
+	if (pcinfo->valid && !wl->status.map.lps && !wl->status.map.rf_off) {
+		prptctrl = &pfwinfo->rpt_ctrl.finfo;
+
+		seq_printf(m,
+			   " %-15s : h2c_cnt=%d(fail:%d, fw_recv:%d), c2h_cnt=%d(fw_send:%d), ",
+			   "[summary]", pfwinfo->cnt_h2c,
+			   pfwinfo->cnt_h2c_fail, prptctrl->h2c_cnt,
+			   pfwinfo->cnt_c2h, prptctrl->c2h_cnt);
+
+		seq_printf(m,
+			   "rpt_cnt=%d(fw_send:%d), rpt_map=0x%x, dm_error_map:0x%x",
+			   pfwinfo->event[BTF_EVNT_RPT], prptctrl->rpt_cnt,
+			   prptctrl->rpt_enable, dm->error.val);
+
+		_chk_btc_err(rtwdev, BTC_DCNT_RPT_FREEZE,
+			     pfwinfo->event[BTF_EVNT_RPT]);
+
+		if (dm->error.map.wl_fw_hang)
+			seq_puts(m, " (WL FW Hang!!)");
+		seq_puts(m, "\n");
+		seq_printf(m,
+			   " %-15s : send_ok:%d, send_fail:%d, recv:%d",
+			   "[mailbox]", prptctrl->mb_send_ok_cnt,
+			   prptctrl->mb_send_fail_cnt, prptctrl->mb_recv_cnt);
+
+		seq_printf(m,
+			   "(A2DP_empty:%d, A2DP_flowstop:%d, A2DP_full:%d)\n",
+			   prptctrl->mb_a2dp_empty_cnt,
+			   prptctrl->mb_a2dp_flct_cnt,
+			   prptctrl->mb_a2dp_full_cnt);
+
+		seq_printf(m,
+			   " %-15s : wl_rfk[req:%d/go:%d/reject:%d/timeout:%d]",
+			   "[RFK]", cx->cnt_wl[BTC_WCNT_RFK_REQ],
+			   cx->cnt_wl[BTC_WCNT_RFK_GO],
+			   cx->cnt_wl[BTC_WCNT_RFK_REJECT],
+			   cx->cnt_wl[BTC_WCNT_RFK_TIMEOUT]);
+
+		seq_printf(m,
+			   ", bt_rfk[req:%d/go:%d/reject:%d/timeout:%d/fail:%d]\n",
+			   prptctrl->bt_rfk_cnt[BTC_BCNT_RFK_REQ],
+			   prptctrl->bt_rfk_cnt[BTC_BCNT_RFK_GO],
+			   prptctrl->bt_rfk_cnt[BTC_BCNT_RFK_REJECT],
+			   prptctrl->bt_rfk_cnt[BTC_BCNT_RFK_TIMEOUT],
+			   prptctrl->bt_rfk_cnt[BTC_BCNT_RFK_FAIL]);
+
+		if (prptctrl->bt_rfk_cnt[BTC_BCNT_RFK_TIMEOUT] > 0)
+			bt->rfk_info.map.timeout = 1;
+		else
+			bt->rfk_info.map.timeout = 0;
+
+		dm->error.map.wl_rfk_timeout = bt->rfk_info.map.timeout;
+	} else {
+		seq_printf(m,
+			   " %-15s : h2c_cnt=%d(fail:%d), c2h_cnt=%d, rpt_cnt=%d, rpt_map=0x%x",
+			   "[summary]", pfwinfo->cnt_h2c,
+			   pfwinfo->cnt_h2c_fail, pfwinfo->cnt_c2h,
+			   pfwinfo->event[BTF_EVNT_RPT],
+			   btc->fwinfo.rpt_en_map);
+		seq_puts(m, " (WL FW report invalid!!)\n");
+	}
+
+	for (i = 0; i < BTC_NCNT_NUM; i++)
+		cnt_sum += dm->cnt_notify[i];
+
+	seq_printf(m,
+		   " %-15s : total=%d, show_coex_info=%d, power_on=%d, init_coex=%d, ",
+		   "[notify_cnt]", cnt_sum, cnt[BTC_NCNT_SHOW_COEX_INFO],
+		   cnt[BTC_NCNT_POWER_ON], cnt[BTC_NCNT_INIT_COEX]);
+
+	seq_printf(m,
+		   "power_off=%d, radio_state=%d, role_info=%d, wl_rfk=%d, wl_sta=%d\n",
+		   cnt[BTC_NCNT_POWER_OFF], cnt[BTC_NCNT_RADIO_STATE],
+		   cnt[BTC_NCNT_ROLE_INFO], cnt[BTC_NCNT_WL_RFK],
+		   cnt[BTC_NCNT_WL_STA]);
+
+	seq_printf(m,
+		   " %-15s : scan_start=%d, scan_finish=%d, switch_band=%d, special_pkt=%d, ",
+		   "[notify_cnt]", cnt[BTC_NCNT_SCAN_START],
+		   cnt[BTC_NCNT_SCAN_FINISH], cnt[BTC_NCNT_SWITCH_BAND],
+		   cnt[BTC_NCNT_SPECIAL_PACKET]);
+
+	seq_printf(m,
+		   "timer=%d, control=%d, customerize=%d\n",
+		   cnt[BTC_NCNT_TIMER], cnt[BTC_NCNT_CONTROL],
+		   cnt[BTC_NCNT_CUSTOMERIZE]);
+}
+
+void rtw89_btc_dump_info(struct rtw89_dev *rtwdev, struct seq_file *m)
+{
+	struct rtw89_fw_suit *fw_suit = &rtwdev->fw.normal;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	struct rtw89_btc_bt_info *bt = &cx->bt;
+
+	seq_puts(m, "=========================================\n");
+	seq_printf(m, "WL FW / BT FW		%d.%d.%d.%d / NA\n",
+		   fw_suit->major_ver, fw_suit->minor_ver,
+		   fw_suit->sub_ver, fw_suit->sub_idex);
+	seq_printf(m, "manual			%d\n", btc->ctrl.manual);
+
+	seq_puts(m, "=========================================\n");
+
+	seq_printf(m, "\n\r %-15s : raw_data[%02x %02x %02x %02x %02x %02x] (type:%s/cnt:%d/same:%d)",
+		   "[bt_info]",
+		   bt->raw_info[2], bt->raw_info[3],
+		   bt->raw_info[4], bt->raw_info[5],
+		   bt->raw_info[6], bt->raw_info[7],
+		   bt->raw_info[0] == BTC_BTINFO_AUTO ? "auto" : "reply",
+		   cx->cnt_bt[BTC_BCNT_INFOUPDATE],
+		   cx->cnt_bt[BTC_BCNT_INFOSAME]);
+
+	seq_puts(m, "\n=========================================\n");
+
+	_show_cx_info(rtwdev, m);
+	_show_wl_info(rtwdev, m);
+	_show_bt_info(rtwdev, m);
+	_show_dm_info(rtwdev, m);
+	_show_fw_dm_msg(rtwdev, m);
+	_show_mreg(rtwdev, m);
+	_show_summary(rtwdev, m);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/coex.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/coex.h
@@ -0,0 +1,181 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_COEX_H__
+#define __RTW89_COEX_H__
+
+#include "core.h"
+
+enum btc_mode {
+	BTC_MODE_NORMAL,
+	BTC_MODE_WL,
+	BTC_MODE_BT,
+	BTC_MODE_WLOFF,
+	BTC_MODE_MAX
+};
+
+enum btc_wl_rfk_type {
+	BTC_WRFKT_IQK = 0,
+	BTC_WRFKT_LCK = 1,
+	BTC_WRFKT_DPK = 2,
+	BTC_WRFKT_TXGAPK = 3,
+	BTC_WRFKT_DACK = 4,
+	BTC_WRFKT_RXDCK = 5,
+	BTC_WRFKT_TSSI = 6,
+};
+
+#define NM_EXEC false
+#define FC_EXEC true
+
+#define RTW89_COEX_ACT1_WORK_PERIOD	round_jiffies_relative(HZ * 4)
+#define RTW89_COEX_BT_DEVINFO_WORK_PERIOD	round_jiffies_relative(HZ * 16)
+#define RTW89_COEX_RFK_CHK_WORK_PERIOD	msecs_to_jiffies(300)
+#define BTC_RFK_PATH_MAP GENMASK(3, 0)
+#define BTC_RFK_PHY_MAP GENMASK(5, 4)
+#define BTC_RFK_BAND_MAP GENMASK(7, 6)
+
+enum btc_wl_rfk_state {
+	BTC_WRFK_STOP = 0,
+	BTC_WRFK_START = 1,
+	BTC_WRFK_ONESHOT_START = 2,
+	BTC_WRFK_ONESHOT_STOP = 3,
+};
+
+enum btc_pri {
+	BTC_PRI_MASK_RX_RESP = 0,
+	BTC_PRI_MASK_TX_RESP,
+	BTC_PRI_MASK_BEACON,
+	BTC_PRI_MASK_RX_CCK,
+	BTC_PRI_MASK_TX_MNGQ,
+	BTC_PRI_MASK_MAX,
+};
+
+enum btc_bt_trs {
+	BTC_BT_SS_GROUP = 0x0,
+	BTC_BT_TX_GROUP = 0x2,
+	BTC_BT_RX_GROUP = 0x3,
+	BTC_BT_MAX_GROUP,
+};
+
+enum btc_rssi_st {
+	BTC_RSSI_ST_LOW = 0x0,
+	BTC_RSSI_ST_HIGH,
+	BTC_RSSI_ST_STAY_LOW,
+	BTC_RSSI_ST_STAY_HIGH,
+	BTC_RSSI_ST_MAX
+};
+
+#define	BTC_RSSI_HIGH(_rssi_) \
+	({typeof(_rssi_) __rssi = (_rssi_); \
+	  ((__rssi == BTC_RSSI_ST_HIGH || \
+	    __rssi == BTC_RSSI_ST_STAY_HIGH) ? 1 : 0); })
+
+#define	BTC_RSSI_LOW(_rssi_) \
+	({typeof(_rssi_) __rssi = (_rssi_); \
+	  ((__rssi == BTC_RSSI_ST_LOW || \
+	    __rssi == BTC_RSSI_ST_STAY_LOW) ? 1 : 0); })
+
+#define BTC_RSSI_CHANGE(_rssi_) \
+	({typeof(_rssi_) __rssi = (_rssi_); \
+	  ((__rssi == BTC_RSSI_ST_LOW || \
+	    __rssi == BTC_RSSI_ST_HIGH) ? 1 : 0); })
+
+enum btc_ant {
+	BTC_ANT_SHARED = 0,
+	BTC_ANT_DEDICATED,
+	BTC_ANTTYPE_MAX
+};
+
+enum btc_bt_btg {
+	BTC_BT_ALONE = 0,
+	BTC_BT_BTG
+};
+
+enum btc_switch {
+	BTC_SWITCH_INTERNAL = 0,
+	BTC_SWITCH_EXTERNAL
+};
+
+enum btc_pkt_type {
+	PACKET_DHCP,
+	PACKET_ARP,
+	PACKET_EAPOL,
+	PACKET_EAPOL_END,
+	PACKET_ICMP,
+	PACKET_MAX
+};
+
+enum btc_bt_mailbox_id {
+	BTC_BTINFO_REPLY = 0x23,
+	BTC_BTINFO_AUTO = 0x27
+};
+
+enum btc_role_state {
+	BTC_ROLE_START,
+	BTC_ROLE_STOP,
+	BTC_ROLE_CHG_TYPE,
+	BTC_ROLE_MSTS_STA_CONN_START,
+	BTC_ROLE_MSTS_STA_CONN_END,
+	BTC_ROLE_MSTS_STA_DIS_CONN,
+	BTC_ROLE_MSTS_AP_START,
+	BTC_ROLE_MSTS_AP_STOP,
+	BTC_ROLE_STATE_UNKNOWN
+};
+
+enum btc_rfctrl {
+	BTC_RFCTRL_WL_OFF,
+	BTC_RFCTRL_WL_ON,
+	BTC_RFCTRL_FW_CTRL,
+	BTC_RFCTRL_MAX
+};
+
+void rtw89_btc_ntfy_poweron(struct rtw89_dev *rtwdev);
+void rtw89_btc_ntfy_poweroff(struct rtw89_dev *rtwdev);
+void rtw89_btc_ntfy_init(struct rtw89_dev *rtwdev, u8 mode);
+void rtw89_btc_ntfy_scan_start(struct rtw89_dev *rtwdev, u8 phy_idx, u8 band);
+void rtw89_btc_ntfy_scan_finish(struct rtw89_dev *rtwdev, u8 phy_idx);
+void rtw89_btc_ntfy_switch_band(struct rtw89_dev *rtwdev, u8 phy_idx, u8 band);
+void rtw89_btc_ntfy_specific_packet(struct rtw89_dev *rtwdev,
+				    enum btc_pkt_type pkt_type);
+void rtw89_btc_ntfy_eapol_packet_work(struct work_struct *work);
+void rtw89_btc_ntfy_arp_packet_work(struct work_struct *work);
+void rtw89_btc_ntfy_dhcp_packet_work(struct work_struct *work);
+void rtw89_btc_ntfy_icmp_packet_work(struct work_struct *work);
+void rtw89_btc_ntfy_role_info(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			      struct rtw89_sta *rtwsta, enum btc_role_state state);
+void rtw89_btc_ntfy_radio_state(struct rtw89_dev *rtwdev, enum btc_rfctrl rf_state);
+void rtw89_btc_ntfy_wl_rfk(struct rtw89_dev *rtwdev, u8 phy_map,
+			   enum btc_wl_rfk_type type,
+			   enum btc_wl_rfk_state state);
+void rtw89_btc_ntfy_wl_sta(struct rtw89_dev *rtwdev);
+void rtw89_btc_c2h_handle(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			  u32 len, u8 class, u8 func);
+void rtw89_btc_dump_info(struct rtw89_dev *rtwdev, struct seq_file *m);
+void rtw89_coex_act1_work(struct work_struct *work);
+void rtw89_coex_bt_devinfo_work(struct work_struct *work);
+void rtw89_coex_rfk_chk_work(struct work_struct *work);
+void rtw89_coex_power_on(struct rtw89_dev *rtwdev);
+
+static inline u8 rtw89_btc_phymap(struct rtw89_dev *rtwdev,
+				  enum rtw89_phy_idx phy_idx,
+				  enum rtw89_rf_path_bit paths)
+{
+	struct rtw89_hal *hal = &rtwdev->hal;
+	u8 phy_map;
+
+	phy_map = FIELD_PREP(BTC_RFK_PATH_MAP, paths) |
+		  FIELD_PREP(BTC_RFK_PHY_MAP, BIT(phy_idx)) |
+		  FIELD_PREP(BTC_RFK_BAND_MAP, hal->current_band_type);
+
+	return phy_map;
+}
+
+static inline u8 rtw89_btc_path_phymap(struct rtw89_dev *rtwdev,
+				       enum rtw89_phy_idx phy_idx,
+				       enum rtw89_rf_path path)
+{
+	return rtw89_btc_phymap(rtwdev, phy_idx, BIT(path));
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/core.c
@@ -0,0 +1,2502 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "coex.h"
+#include "core.h"
+#include "efuse.h"
+#include "fw.h"
+#include "mac.h"
+#include "phy.h"
+#include "ps.h"
+#include "reg.h"
+#include "sar.h"
+#include "ser.h"
+#include "txrx.h"
+#include "util.h"
+
+static bool rtw89_disable_ps_mode;
+module_param_named(disable_ps_mode, rtw89_disable_ps_mode, bool, 0644);
+MODULE_PARM_DESC(disable_ps_mode, "Set Y to disable low power mode");
+
+static struct ieee80211_channel rtw89_channels_2ghz[] = {
+	{ .center_freq = 2412, .hw_value = 1, },
+	{ .center_freq = 2417, .hw_value = 2, },
+	{ .center_freq = 2422, .hw_value = 3, },
+	{ .center_freq = 2427, .hw_value = 4, },
+	{ .center_freq = 2432, .hw_value = 5, },
+	{ .center_freq = 2437, .hw_value = 6, },
+	{ .center_freq = 2442, .hw_value = 7, },
+	{ .center_freq = 2447, .hw_value = 8, },
+	{ .center_freq = 2452, .hw_value = 9, },
+	{ .center_freq = 2457, .hw_value = 10, },
+	{ .center_freq = 2462, .hw_value = 11, },
+	{ .center_freq = 2467, .hw_value = 12, },
+	{ .center_freq = 2472, .hw_value = 13, },
+	{ .center_freq = 2484, .hw_value = 14, },
+};
+
+static struct ieee80211_channel rtw89_channels_5ghz[] = {
+	{.center_freq = 5180, .hw_value = 36,},
+	{.center_freq = 5200, .hw_value = 40,},
+	{.center_freq = 5220, .hw_value = 44,},
+	{.center_freq = 5240, .hw_value = 48,},
+	{.center_freq = 5260, .hw_value = 52,},
+	{.center_freq = 5280, .hw_value = 56,},
+	{.center_freq = 5300, .hw_value = 60,},
+	{.center_freq = 5320, .hw_value = 64,},
+	{.center_freq = 5500, .hw_value = 100,},
+	{.center_freq = 5520, .hw_value = 104,},
+	{.center_freq = 5540, .hw_value = 108,},
+	{.center_freq = 5560, .hw_value = 112,},
+	{.center_freq = 5580, .hw_value = 116,},
+	{.center_freq = 5600, .hw_value = 120,},
+	{.center_freq = 5620, .hw_value = 124,},
+	{.center_freq = 5640, .hw_value = 128,},
+	{.center_freq = 5660, .hw_value = 132,},
+	{.center_freq = 5680, .hw_value = 136,},
+	{.center_freq = 5700, .hw_value = 140,},
+	{.center_freq = 5720, .hw_value = 144,},
+	{.center_freq = 5745, .hw_value = 149,},
+	{.center_freq = 5765, .hw_value = 153,},
+	{.center_freq = 5785, .hw_value = 157,},
+	{.center_freq = 5805, .hw_value = 161,},
+	{.center_freq = 5825, .hw_value = 165,
+	 .flags = IEEE80211_CHAN_NO_HT40MINUS},
+};
+
+static struct ieee80211_rate rtw89_bitrates[] = {
+	{ .bitrate = 10,  .hw_value = 0x00, },
+	{ .bitrate = 20,  .hw_value = 0x01, },
+	{ .bitrate = 55,  .hw_value = 0x02, },
+	{ .bitrate = 110, .hw_value = 0x03, },
+	{ .bitrate = 60,  .hw_value = 0x04, },
+	{ .bitrate = 90,  .hw_value = 0x05, },
+	{ .bitrate = 120, .hw_value = 0x06, },
+	{ .bitrate = 180, .hw_value = 0x07, },
+	{ .bitrate = 240, .hw_value = 0x08, },
+	{ .bitrate = 360, .hw_value = 0x09, },
+	{ .bitrate = 480, .hw_value = 0x0a, },
+	{ .bitrate = 540, .hw_value = 0x0b, },
+};
+
+u16 rtw89_ra_report_to_bitrate(struct rtw89_dev *rtwdev, u8 rpt_rate)
+{
+	struct ieee80211_rate rate;
+
+	if (unlikely(rpt_rate >= ARRAY_SIZE(rtw89_bitrates))) {
+		rtw89_info(rtwdev, "invalid rpt rate %d\n", rpt_rate);
+		return 0;
+	}
+
+	rate = rtw89_bitrates[rpt_rate];
+
+	return rate.bitrate;
+}
+
+static struct ieee80211_supported_band rtw89_sband_2ghz = {
+	.band		= NL80211_BAND_2GHZ,
+	.channels	= rtw89_channels_2ghz,
+	.n_channels	= ARRAY_SIZE(rtw89_channels_2ghz),
+	.bitrates	= rtw89_bitrates,
+	.n_bitrates	= ARRAY_SIZE(rtw89_bitrates),
+	.ht_cap		= {0},
+	.vht_cap	= {0},
+};
+
+static struct ieee80211_supported_band rtw89_sband_5ghz = {
+	.band		= NL80211_BAND_5GHZ,
+	.channels	= rtw89_channels_5ghz,
+	.n_channels	= ARRAY_SIZE(rtw89_channels_5ghz),
+
+	/* 5G has no CCK rates, 1M/2M/5.5M/11M */
+	.bitrates	= rtw89_bitrates + 4,
+	.n_bitrates	= ARRAY_SIZE(rtw89_bitrates) - 4,
+	.ht_cap		= {0},
+	.vht_cap	= {0},
+};
+
+static void rtw89_traffic_stats_accu(struct rtw89_dev *rtwdev,
+				     struct rtw89_traffic_stats *stats,
+				     struct sk_buff *skb, bool tx)
+{
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+
+	if (!ieee80211_is_data(hdr->frame_control))
+		return;
+
+	if (is_broadcast_ether_addr(hdr->addr1) ||
+	    is_multicast_ether_addr(hdr->addr1))
+		return;
+
+	if (tx) {
+		stats->tx_cnt++;
+		stats->tx_unicast += skb->len;
+	} else {
+		stats->rx_cnt++;
+		stats->rx_unicast += skb->len;
+	}
+}
+
+static void rtw89_get_channel_params(struct cfg80211_chan_def *chandef,
+				     struct rtw89_channel_params *chan_param)
+{
+	struct ieee80211_channel *channel = chandef->chan;
+	enum nl80211_chan_width width = chandef->width;
+	u8 *cch_by_bw = chan_param->cch_by_bw;
+	u32 primary_freq, center_freq;
+	u8 center_chan;
+	u8 bandwidth = RTW89_CHANNEL_WIDTH_20;
+	u8 primary_chan_idx = 0;
+	u8 i;
+
+	center_chan = channel->hw_value;
+	primary_freq = channel->center_freq;
+	center_freq = chandef->center_freq1;
+
+	/* assign the center channel used while 20M bw is selected */
+	cch_by_bw[RTW89_CHANNEL_WIDTH_20] = channel->hw_value;
+
+	switch (width) {
+	case NL80211_CHAN_WIDTH_20_NOHT:
+	case NL80211_CHAN_WIDTH_20:
+		bandwidth = RTW89_CHANNEL_WIDTH_20;
+		primary_chan_idx = RTW89_SC_DONT_CARE;
+		break;
+	case NL80211_CHAN_WIDTH_40:
+		bandwidth = RTW89_CHANNEL_WIDTH_40;
+		if (primary_freq > center_freq) {
+			primary_chan_idx = RTW89_SC_20_UPPER;
+			center_chan -= 2;
+		} else {
+			primary_chan_idx = RTW89_SC_20_LOWER;
+			center_chan += 2;
+		}
+		break;
+	case NL80211_CHAN_WIDTH_80:
+		bandwidth = RTW89_CHANNEL_WIDTH_80;
+		if (primary_freq > center_freq) {
+			if (primary_freq - center_freq == 10) {
+				primary_chan_idx = RTW89_SC_20_UPPER;
+				center_chan -= 2;
+			} else {
+				primary_chan_idx = RTW89_SC_20_UPMOST;
+				center_chan -= 6;
+			}
+			/* assign the center channel used
+			 * while 40M bw is selected
+			 */
+			cch_by_bw[RTW89_CHANNEL_WIDTH_40] = center_chan + 4;
+		} else {
+			if (center_freq - primary_freq == 10) {
+				primary_chan_idx = RTW89_SC_20_LOWER;
+				center_chan += 2;
+			} else {
+				primary_chan_idx = RTW89_SC_20_LOWEST;
+				center_chan += 6;
+			}
+			/* assign the center channel used
+			 * while 40M bw is selected
+			 */
+			cch_by_bw[RTW89_CHANNEL_WIDTH_40] = center_chan - 4;
+		}
+		break;
+	default:
+		center_chan = 0;
+		break;
+	}
+
+	chan_param->center_chan = center_chan;
+	chan_param->primary_chan = channel->hw_value;
+	chan_param->bandwidth = bandwidth;
+	chan_param->pri_ch_idx = primary_chan_idx;
+
+	/* assign the center channel used while current bw is selected */
+	cch_by_bw[bandwidth] = center_chan;
+
+	for (i = bandwidth + 1; i <= RTW89_MAX_CHANNEL_WIDTH; i++)
+		cch_by_bw[i] = 0;
+}
+
+void rtw89_set_channel(struct rtw89_dev *rtwdev)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct rtw89_channel_params ch_param;
+	struct rtw89_channel_help_params bak;
+	u8 center_chan, bandwidth;
+	u8 band_type;
+	bool band_changed;
+	u8 i;
+
+	rtw89_get_channel_params(&hw->conf.chandef, &ch_param);
+	if (WARN(ch_param.center_chan == 0, "Invalid channel\n"))
+		return;
+
+	center_chan = ch_param.center_chan;
+	bandwidth = ch_param.bandwidth;
+	band_type = center_chan > 14 ? RTW89_BAND_5G : RTW89_BAND_2G;
+	band_changed = hal->current_band_type != band_type ||
+		       hal->current_channel == 0;
+
+	hal->current_band_width = bandwidth;
+	hal->current_channel = center_chan;
+	hal->current_primary_channel = ch_param.primary_chan;
+	hal->current_band_type = band_type;
+
+	switch (center_chan) {
+	case 1 ... 14:
+		hal->current_subband = RTW89_CH_2G;
+		break;
+	case 36 ... 64:
+		hal->current_subband = RTW89_CH_5G_BAND_1;
+		break;
+	case 100 ... 144:
+		hal->current_subband = RTW89_CH_5G_BAND_3;
+		break;
+	case 149 ... 177:
+		hal->current_subband = RTW89_CH_5G_BAND_4;
+		break;
+	}
+
+	for (i = RTW89_CHANNEL_WIDTH_20; i <= RTW89_MAX_CHANNEL_WIDTH; i++)
+		hal->cch_by_bw[i] = ch_param.cch_by_bw[i];
+
+	rtw89_chip_set_channel_prepare(rtwdev, &bak);
+
+	chip->ops->set_channel(rtwdev, &ch_param);
+
+	rtw89_chip_set_txpwr(rtwdev);
+
+	rtw89_chip_set_channel_done(rtwdev, &bak);
+
+	if (band_changed) {
+		rtw89_btc_ntfy_switch_band(rtwdev, RTW89_PHY_0, hal->current_band_type);
+		rtw89_chip_rfk_band_changed(rtwdev);
+	}
+}
+
+static enum rtw89_core_tx_type
+rtw89_core_get_tx_type(struct rtw89_dev *rtwdev,
+		       struct sk_buff *skb)
+{
+	struct ieee80211_hdr *hdr = (void *)skb->data;
+	__le16 fc = hdr->frame_control;
+
+	if (ieee80211_is_mgmt(fc) || ieee80211_is_nullfunc(fc))
+		return RTW89_CORE_TX_TYPE_MGMT;
+
+	return RTW89_CORE_TX_TYPE_DATA;
+}
+
+static void
+rtw89_core_tx_update_ampdu_info(struct rtw89_dev *rtwdev,
+				struct rtw89_core_tx_request *tx_req, u8 tid)
+{
+	struct ieee80211_sta *sta = tx_req->sta;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct rtw89_sta *rtwsta;
+	u8 ampdu_num;
+
+	if (!sta) {
+		rtw89_warn(rtwdev, "cannot set ampdu info without sta\n");
+		return;
+	}
+
+	rtwsta = (struct rtw89_sta *)sta->drv_priv;
+
+	ampdu_num = (u8)((rtwsta->ampdu_params[tid].agg_num ?
+			  rtwsta->ampdu_params[tid].agg_num :
+			  4 << sta->ht_cap.ampdu_factor) - 1);
+
+	desc_info->agg_en = true;
+	desc_info->ampdu_density = sta->ht_cap.ampdu_density;
+	desc_info->ampdu_num = ampdu_num;
+}
+
+static void
+rtw89_core_tx_update_sec_key(struct rtw89_dev *rtwdev,
+			     struct rtw89_core_tx_request *tx_req)
+{
+	struct ieee80211_vif *vif = tx_req->vif;
+	struct ieee80211_tx_info *info;
+	struct ieee80211_key_conf *key;
+	struct rtw89_vif *rtwvif;
+	struct rtw89_addr_cam_entry *addr_cam;
+	struct rtw89_sec_cam_entry *sec_cam;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct sk_buff *skb = tx_req->skb;
+	u8 sec_type = RTW89_SEC_KEY_TYPE_NONE;
+
+	if (!vif) {
+		rtw89_warn(rtwdev, "cannot set sec key without vif\n");
+		return;
+	}
+
+	rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	addr_cam = &rtwvif->addr_cam;
+
+	info = IEEE80211_SKB_CB(skb);
+	key = info->control.hw_key;
+	sec_cam = addr_cam->sec_entries[key->hw_key_idx];
+	if (!sec_cam) {
+		rtw89_warn(rtwdev, "sec cam entry is empty\n");
+		return;
+	}
+
+	switch (key->cipher) {
+	case WLAN_CIPHER_SUITE_WEP40:
+		sec_type = RTW89_SEC_KEY_TYPE_WEP40;
+		break;
+	case WLAN_CIPHER_SUITE_WEP104:
+		sec_type = RTW89_SEC_KEY_TYPE_WEP104;
+		break;
+	case WLAN_CIPHER_SUITE_TKIP:
+		sec_type = RTW89_SEC_KEY_TYPE_TKIP;
+		break;
+	case WLAN_CIPHER_SUITE_CCMP:
+		sec_type = RTW89_SEC_KEY_TYPE_CCMP128;
+		break;
+	case WLAN_CIPHER_SUITE_CCMP_256:
+		sec_type = RTW89_SEC_KEY_TYPE_CCMP256;
+		break;
+	case WLAN_CIPHER_SUITE_GCMP:
+		sec_type = RTW89_SEC_KEY_TYPE_GCMP128;
+		break;
+	case WLAN_CIPHER_SUITE_GCMP_256:
+		sec_type = RTW89_SEC_KEY_TYPE_GCMP256;
+		break;
+	default:
+		rtw89_warn(rtwdev, "key cipher not supported %d\n", key->cipher);
+		return;
+	}
+
+	desc_info->sec_en = true;
+	desc_info->sec_type = sec_type;
+	desc_info->sec_cam_idx = sec_cam->sec_cam_idx;
+}
+
+static u16 rtw89_core_get_mgmt_rate(struct rtw89_dev *rtwdev,
+				    struct rtw89_core_tx_request *tx_req)
+{
+	struct sk_buff *skb = tx_req->skb;
+	struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+	struct ieee80211_vif *vif = tx_info->control.vif;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	u16 lowest_rate = hal->current_band_type == RTW89_BAND_2G ?
+			  RTW89_HW_RATE_CCK1 : RTW89_HW_RATE_OFDM6;
+
+	if (!vif || !vif->bss_conf.basic_rates || !tx_req->sta)
+		return lowest_rate;
+
+	return __ffs(vif->bss_conf.basic_rates) + lowest_rate;
+}
+
+static void
+rtw89_core_tx_update_mgmt_info(struct rtw89_dev *rtwdev,
+			       struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	u8 qsel, ch_dma;
+
+	qsel = RTW89_TX_QSEL_B0_MGMT;
+	ch_dma = rtw89_core_get_ch_dma(rtwdev, qsel);
+
+	desc_info->qsel = RTW89_TX_QSEL_B0_MGMT;
+	desc_info->ch_dma = ch_dma;
+
+	/* fixed data rate for mgmt frames */
+	desc_info->en_wd_info = true;
+	desc_info->use_rate = true;
+	desc_info->dis_data_fb = true;
+	desc_info->data_rate = rtw89_core_get_mgmt_rate(rtwdev, tx_req);
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+		    "tx mgmt frame with rate 0x%x on channel %d (bw %d)\n",
+		    desc_info->data_rate, rtwdev->hal.current_channel,
+		    rtwdev->hal.current_band_width);
+}
+
+static void
+rtw89_core_tx_update_h2c_info(struct rtw89_dev *rtwdev,
+			      struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+
+	desc_info->is_bmc = false;
+	desc_info->wd_page = false;
+	desc_info->ch_dma = RTW89_DMA_H2C;
+}
+
+static void rtw89_core_get_no_ul_ofdma_htc(struct rtw89_dev *rtwdev, __le32 *htc)
+{
+	static const u8 rtw89_bandwidth_to_om[] = {
+		[RTW89_CHANNEL_WIDTH_20] = HTC_OM_CHANNEL_WIDTH_20,
+		[RTW89_CHANNEL_WIDTH_40] = HTC_OM_CHANNEL_WIDTH_40,
+		[RTW89_CHANNEL_WIDTH_80] = HTC_OM_CHANNEL_WIDTH_80,
+		[RTW89_CHANNEL_WIDTH_160] = HTC_OM_CHANNEL_WIDTH_160_OR_80_80,
+		[RTW89_CHANNEL_WIDTH_80_80] = HTC_OM_CHANNEL_WIDTH_160_OR_80_80,
+	};
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	u8 om_bandwidth;
+
+	if (!chip->dis_2g_40m_ul_ofdma ||
+	    hal->current_band_type != RTW89_BAND_2G ||
+	    hal->current_band_width != RTW89_CHANNEL_WIDTH_40)
+		return;
+
+	om_bandwidth = hal->current_band_width < ARRAY_SIZE(rtw89_bandwidth_to_om) ?
+		       rtw89_bandwidth_to_om[hal->current_band_width] : 0;
+	*htc = le32_encode_bits(RTW89_HTC_VARIANT_HE, RTW89_HTC_MASK_VARIANT) |
+	       le32_encode_bits(RTW89_HTC_VARIANT_HE_CID_OM, RTW89_HTC_MASK_CTL_ID) |
+	       le32_encode_bits(hal->rx_nss - 1, RTW89_HTC_MASK_HTC_OM_RX_NSS) |
+	       le32_encode_bits(om_bandwidth, RTW89_HTC_MASK_HTC_OM_CH_WIDTH) |
+	       le32_encode_bits(1, RTW89_HTC_MASK_HTC_OM_UL_MU_DIS) |
+	       le32_encode_bits(hal->tx_nss - 1, RTW89_HTC_MASK_HTC_OM_TX_NSTS) |
+	       le32_encode_bits(0, RTW89_HTC_MASK_HTC_OM_ER_SU_DIS) |
+	       le32_encode_bits(0, RTW89_HTC_MASK_HTC_OM_DL_MU_MIMO_RR) |
+	       le32_encode_bits(0, RTW89_HTC_MASK_HTC_OM_UL_MU_DATA_DIS);
+}
+
+static bool
+__rtw89_core_tx_check_he_qos_htc(struct rtw89_dev *rtwdev,
+				 struct rtw89_core_tx_request *tx_req,
+				 enum btc_pkt_type pkt_type)
+{
+	struct ieee80211_sta *sta = tx_req->sta;
+	struct sk_buff *skb = tx_req->skb;
+	struct ieee80211_hdr *hdr = (void *)skb->data;
+	__le16 fc = hdr->frame_control;
+
+	/* AP IOT issue with EAPoL, ARP and DHCP */
+	if (pkt_type < PACKET_MAX)
+		return false;
+
+	if (!sta || !sta->he_cap.has_he)
+		return false;
+
+	if (!ieee80211_is_data_qos(fc))
+		return false;
+
+	if (skb_headroom(skb) < IEEE80211_HT_CTL_LEN)
+		return false;
+
+	return true;
+}
+
+static void
+__rtw89_core_tx_adjust_he_qos_htc(struct rtw89_dev *rtwdev,
+				  struct rtw89_core_tx_request *tx_req)
+{
+	struct ieee80211_sta *sta = tx_req->sta;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct sk_buff *skb = tx_req->skb;
+	struct ieee80211_hdr *hdr = (void *)skb->data;
+	__le16 fc = hdr->frame_control;
+	void *data;
+	__le32 *htc;
+	u8 *qc;
+	int hdr_len;
+
+	hdr_len = ieee80211_has_a4(fc) ? 32 : 26;
+	data = skb_push(skb, IEEE80211_HT_CTL_LEN);
+	memmove(data, data + IEEE80211_HT_CTL_LEN, hdr_len);
+
+	hdr = data;
+	htc = data + hdr_len;
+	hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_ORDER);
+	*htc = rtwsta->htc_template ? rtwsta->htc_template :
+	       le32_encode_bits(RTW89_HTC_VARIANT_HE, RTW89_HTC_MASK_VARIANT) |
+	       le32_encode_bits(RTW89_HTC_VARIANT_HE_CID_CAS, RTW89_HTC_MASK_CTL_ID);
+
+	qc = data + hdr_len - IEEE80211_QOS_CTL_LEN;
+	qc[0] |= IEEE80211_QOS_CTL_EOSP;
+}
+
+static void
+rtw89_core_tx_update_he_qos_htc(struct rtw89_dev *rtwdev,
+				struct rtw89_core_tx_request *tx_req,
+				enum btc_pkt_type pkt_type)
+{
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct ieee80211_vif *vif = tx_req->vif;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	if (!__rtw89_core_tx_check_he_qos_htc(rtwdev, tx_req, pkt_type))
+		goto desc_bk;
+
+	__rtw89_core_tx_adjust_he_qos_htc(rtwdev, tx_req);
+
+	desc_info->pkt_size += IEEE80211_HT_CTL_LEN;
+	desc_info->a_ctrl_bsr = true;
+
+desc_bk:
+	if (!rtwvif || rtwvif->last_a_ctrl == desc_info->a_ctrl_bsr)
+		return;
+
+	rtwvif->last_a_ctrl = desc_info->a_ctrl_bsr;
+	desc_info->bk = true;
+}
+
+static void
+rtw89_core_tx_update_data_info(struct rtw89_dev *rtwdev,
+			       struct rtw89_core_tx_request *tx_req)
+{
+	struct ieee80211_vif *vif = tx_req->vif;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct rtw89_phy_rate_pattern *rate_pattern = &rtwvif->rate_pattern;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct sk_buff *skb = tx_req->skb;
+	u8 tid, tid_indicate;
+	u8 qsel, ch_dma;
+
+	tid = skb->priority & IEEE80211_QOS_CTL_TAG1D_MASK;
+	tid_indicate = rtw89_core_get_tid_indicate(rtwdev, tid);
+	qsel = rtw89_core_get_qsel(rtwdev, tid);
+	ch_dma = rtw89_core_get_ch_dma(rtwdev, qsel);
+
+	desc_info->ch_dma = ch_dma;
+	desc_info->tid_indicate = tid_indicate;
+	desc_info->qsel = qsel;
+
+	/* enable wd_info for AMPDU */
+	desc_info->en_wd_info = true;
+
+	if (IEEE80211_SKB_CB(skb)->flags & IEEE80211_TX_CTL_AMPDU)
+		rtw89_core_tx_update_ampdu_info(rtwdev, tx_req, tid);
+	if (IEEE80211_SKB_CB(skb)->control.hw_key)
+		rtw89_core_tx_update_sec_key(rtwdev, tx_req);
+
+	if (rate_pattern->enable)
+		desc_info->data_retry_lowest_rate = rate_pattern->rate;
+	else if (hal->current_band_type == RTW89_BAND_2G)
+		desc_info->data_retry_lowest_rate = RTW89_HW_RATE_CCK1;
+	else
+		desc_info->data_retry_lowest_rate = RTW89_HW_RATE_OFDM6;
+}
+
+static enum btc_pkt_type
+rtw89_core_tx_btc_spec_pkt_notify(struct rtw89_dev *rtwdev,
+				  struct rtw89_core_tx_request *tx_req)
+{
+	struct sk_buff *skb = tx_req->skb;
+	struct udphdr *udphdr;
+
+	if (IEEE80211_SKB_CB(skb)->control.flags & IEEE80211_TX_CTRL_PORT_CTRL_PROTO) {
+		ieee80211_queue_work(rtwdev->hw, &rtwdev->btc.eapol_notify_work);
+		return PACKET_EAPOL;
+	}
+
+	if (skb->protocol == htons(ETH_P_ARP)) {
+		ieee80211_queue_work(rtwdev->hw, &rtwdev->btc.arp_notify_work);
+		return PACKET_ARP;
+	}
+
+	if (skb->protocol == htons(ETH_P_IP) &&
+	    ip_hdr(skb)->protocol == IPPROTO_UDP) {
+		udphdr = udp_hdr(skb);
+		if (((udphdr->source == htons(67) && udphdr->dest == htons(68)) ||
+		     (udphdr->source == htons(68) && udphdr->dest == htons(67))) &&
+		    skb->len > 282) {
+			ieee80211_queue_work(rtwdev->hw, &rtwdev->btc.dhcp_notify_work);
+			return PACKET_DHCP;
+		}
+	}
+
+	if (skb->protocol == htons(ETH_P_IP) &&
+	    ip_hdr(skb)->protocol == IPPROTO_ICMP) {
+		ieee80211_queue_work(rtwdev->hw, &rtwdev->btc.icmp_notify_work);
+		return PACKET_ICMP;
+	}
+
+	return PACKET_MAX;
+}
+
+static void
+rtw89_core_tx_update_desc_info(struct rtw89_dev *rtwdev,
+			       struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct sk_buff *skb = tx_req->skb;
+	struct ieee80211_hdr *hdr = (void *)skb->data;
+	enum rtw89_core_tx_type tx_type;
+	enum btc_pkt_type pkt_type;
+	bool is_bmc;
+	u16 seq;
+
+	seq = (le16_to_cpu(hdr->seq_ctrl) & IEEE80211_SCTL_SEQ) >> 4;
+	if (tx_req->tx_type != RTW89_CORE_TX_TYPE_FWCMD) {
+		tx_type = rtw89_core_get_tx_type(rtwdev, skb);
+		tx_req->tx_type = tx_type;
+	}
+	is_bmc = (is_broadcast_ether_addr(hdr->addr1) ||
+		  is_multicast_ether_addr(hdr->addr1));
+
+	desc_info->seq = seq;
+	desc_info->pkt_size = skb->len;
+	desc_info->is_bmc = is_bmc;
+	desc_info->wd_page = true;
+
+	switch (tx_req->tx_type) {
+	case RTW89_CORE_TX_TYPE_MGMT:
+		rtw89_core_tx_update_mgmt_info(rtwdev, tx_req);
+		break;
+	case RTW89_CORE_TX_TYPE_DATA:
+		rtw89_core_tx_update_data_info(rtwdev, tx_req);
+		pkt_type = rtw89_core_tx_btc_spec_pkt_notify(rtwdev, tx_req);
+		rtw89_core_tx_update_he_qos_htc(rtwdev, tx_req, pkt_type);
+		break;
+	case RTW89_CORE_TX_TYPE_FWCMD:
+		rtw89_core_tx_update_h2c_info(rtwdev, tx_req);
+		break;
+	}
+}
+
+void rtw89_core_tx_kick_off(struct rtw89_dev *rtwdev, u8 qsel)
+{
+	u8 ch_dma;
+
+	ch_dma = rtw89_core_get_ch_dma(rtwdev, qsel);
+
+	rtw89_hci_tx_kick_off(rtwdev, ch_dma);
+}
+
+int rtw89_h2c_tx(struct rtw89_dev *rtwdev,
+		 struct sk_buff *skb, bool fwdl)
+{
+	struct rtw89_core_tx_request tx_req = {0};
+	u32 cnt;
+	int ret;
+
+	tx_req.skb = skb;
+	tx_req.tx_type = RTW89_CORE_TX_TYPE_FWCMD;
+	if (fwdl)
+		tx_req.desc_info.fw_dl = true;
+
+	rtw89_core_tx_update_desc_info(rtwdev, &tx_req);
+
+	if (!fwdl)
+		rtw89_hex_dump(rtwdev, RTW89_DBG_FW, "H2C: ", skb->data, skb->len);
+
+	cnt = rtw89_hci_check_and_reclaim_tx_resource(rtwdev, RTW89_TXCH_CH12);
+	if (cnt == 0) {
+		rtw89_err(rtwdev, "no tx fwcmd resource\n");
+		return -ENOSPC;
+	}
+
+	ret = rtw89_hci_tx_write(rtwdev, &tx_req);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to transmit skb to HCI\n");
+		return ret;
+	}
+	rtw89_hci_tx_kick_off(rtwdev, RTW89_TXCH_CH12);
+
+	return 0;
+}
+
+int rtw89_core_tx_write(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+			struct ieee80211_sta *sta, struct sk_buff *skb, int *qsel)
+{
+	struct rtw89_core_tx_request tx_req = {0};
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	int ret;
+
+	tx_req.skb = skb;
+	tx_req.sta = sta;
+	tx_req.vif = vif;
+
+	rtw89_traffic_stats_accu(rtwdev, &rtwdev->stats, skb, true);
+	rtw89_traffic_stats_accu(rtwdev, &rtwvif->stats, skb, true);
+	rtw89_core_tx_update_desc_info(rtwdev, &tx_req);
+	ret = rtw89_hci_tx_write(rtwdev, &tx_req);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to transmit skb to HCI\n");
+		return ret;
+	}
+
+	if (qsel)
+		*qsel = tx_req.desc_info.qsel;
+
+	return 0;
+}
+
+static __le32 rtw89_build_txwd_body0(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_BODY0_WP_OFFSET, desc_info->wp_offset) |
+		    FIELD_PREP(RTW89_TXWD_BODY0_WD_INFO_EN, desc_info->en_wd_info) |
+		    FIELD_PREP(RTW89_TXWD_BODY0_CHANNEL_DMA, desc_info->ch_dma) |
+		    FIELD_PREP(RTW89_TXWD_BODY0_HDR_LLC_LEN, desc_info->hdr_llc_len) |
+		    FIELD_PREP(RTW89_TXWD_BODY0_WD_PAGE, desc_info->wd_page) |
+		    FIELD_PREP(RTW89_TXWD_BODY0_FW_DL, desc_info->fw_dl);
+
+	return cpu_to_le32(dword);
+}
+
+static __le32 rtw89_build_txwd_body2(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_BODY2_TID_INDICATE, desc_info->tid_indicate) |
+		    FIELD_PREP(RTW89_TXWD_BODY2_QSEL, desc_info->qsel) |
+		    FIELD_PREP(RTW89_TXWD_BODY2_TXPKT_SIZE, desc_info->pkt_size);
+
+	return cpu_to_le32(dword);
+}
+
+static __le32 rtw89_build_txwd_body3(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_BODY3_SW_SEQ, desc_info->seq) |
+		    FIELD_PREP(RTW89_TXWD_BODY3_AGG_EN, desc_info->agg_en) |
+		    FIELD_PREP(RTW89_TXWD_BODY3_BK, desc_info->bk);
+
+	return cpu_to_le32(dword);
+}
+
+static __le32 rtw89_build_txwd_info0(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_INFO0_USE_RATE, desc_info->use_rate) |
+		    FIELD_PREP(RTW89_TXWD_INFO0_DATA_RATE, desc_info->data_rate) |
+		    FIELD_PREP(RTW89_TXWD_INFO0_DISDATAFB, desc_info->dis_data_fb);
+
+	return cpu_to_le32(dword);
+}
+
+static __le32 rtw89_build_txwd_info1(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_INFO1_MAX_AGGNUM, desc_info->ampdu_num) |
+		    FIELD_PREP(RTW89_TXWD_INFO1_A_CTRL_BSR, desc_info->a_ctrl_bsr) |
+		    FIELD_PREP(RTW89_TXWD_INFO1_DATA_RTY_LOWEST_RATE,
+			       desc_info->data_retry_lowest_rate);
+
+	return cpu_to_le32(dword);
+}
+
+static __le32 rtw89_build_txwd_info2(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_INFO2_AMPDU_DENSITY, desc_info->ampdu_density) |
+		    FIELD_PREP(RTW89_TXWD_INFO2_SEC_TYPE, desc_info->sec_type) |
+		    FIELD_PREP(RTW89_TXWD_INFO2_SEC_HW_ENC, desc_info->sec_en) |
+		    FIELD_PREP(RTW89_TXWD_INFO2_SEC_CAM_IDX, desc_info->sec_cam_idx);
+
+	return cpu_to_le32(dword);
+}
+
+static __le32 rtw89_build_txwd_info4(struct rtw89_tx_desc_info *desc_info)
+{
+	u32 dword = FIELD_PREP(RTW89_TXWD_INFO4_RTS_EN, 1) |
+		    FIELD_PREP(RTW89_TXWD_INFO4_HW_RTS_EN, 1);
+
+	return cpu_to_le32(dword);
+}
+
+void rtw89_core_fill_txdesc(struct rtw89_dev *rtwdev,
+			    struct rtw89_tx_desc_info *desc_info,
+			    void *txdesc)
+{
+	struct rtw89_txwd_body *txwd_body = (struct rtw89_txwd_body *)txdesc;
+	struct rtw89_txwd_info *txwd_info;
+
+	txwd_body->dword0 = rtw89_build_txwd_body0(desc_info);
+	txwd_body->dword2 = rtw89_build_txwd_body2(desc_info);
+	txwd_body->dword3 = rtw89_build_txwd_body3(desc_info);
+
+	if (!desc_info->en_wd_info)
+		return;
+
+	txwd_info = (struct rtw89_txwd_info *)(txwd_body + 1);
+	txwd_info->dword0 = rtw89_build_txwd_info0(desc_info);
+	txwd_info->dword1 = rtw89_build_txwd_info1(desc_info);
+	txwd_info->dword2 = rtw89_build_txwd_info2(desc_info);
+	txwd_info->dword4 = rtw89_build_txwd_info4(desc_info);
+
+}
+EXPORT_SYMBOL(rtw89_core_fill_txdesc);
+
+static int rtw89_core_rx_process_mac_ppdu(struct rtw89_dev *rtwdev,
+					  struct sk_buff *skb,
+					  struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	bool rx_cnt_valid = false;
+	u8 plcp_size = 0;
+	u8 usr_num = 0;
+	u8 *phy_sts;
+
+	rx_cnt_valid = RTW89_GET_RXINFO_RX_CNT_VLD(skb->data);
+	plcp_size = RTW89_GET_RXINFO_PLCP_LEN(skb->data) << 3;
+	usr_num = RTW89_GET_RXINFO_USR_NUM(skb->data);
+	if (usr_num > RTW89_PPDU_MAX_USR) {
+		rtw89_warn(rtwdev, "Invalid user number in mac info\n");
+		return -EINVAL;
+	}
+
+	phy_sts = skb->data + RTW89_PPDU_MAC_INFO_SIZE;
+	phy_sts += usr_num * RTW89_PPDU_MAC_INFO_USR_SIZE;
+	/* 8-byte alignment */
+	if (usr_num & BIT(0))
+		phy_sts += RTW89_PPDU_MAC_INFO_USR_SIZE;
+	if (rx_cnt_valid)
+		phy_sts += RTW89_PPDU_MAC_RX_CNT_SIZE;
+	phy_sts += plcp_size;
+
+	phy_ppdu->buf = phy_sts;
+	phy_ppdu->len = skb->data + skb->len - phy_sts;
+
+	return 0;
+}
+
+static void rtw89_core_rx_process_phy_ppdu_iter(void *data,
+						struct ieee80211_sta *sta)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_rx_phy_ppdu *phy_ppdu = (struct rtw89_rx_phy_ppdu *)data;
+
+	if (rtwsta->mac_id == phy_ppdu->mac_id && phy_ppdu->to_self)
+		ewma_rssi_add(&rtwsta->avg_rssi, phy_ppdu->rssi_avg);
+}
+
+#define VAR_LEN 0xff
+#define VAR_LEN_UNIT 8
+static u16 rtw89_core_get_phy_status_ie_len(struct rtw89_dev *rtwdev, u8 *addr)
+{
+	static const u8 physts_ie_len_tab[32] = {
+		16, 32, 24, 24, 8, 8, 8, 8, VAR_LEN, 8, VAR_LEN, 176, VAR_LEN,
+		VAR_LEN, VAR_LEN, VAR_LEN, VAR_LEN, VAR_LEN, 16, 24, VAR_LEN,
+		VAR_LEN, VAR_LEN, 0, 24, 24, 24, 24, 32, 32, 32, 32
+	};
+	u16 ie_len;
+	u8 ie;
+
+	ie = RTW89_GET_PHY_STS_IE_TYPE(addr);
+	if (physts_ie_len_tab[ie] != VAR_LEN)
+		ie_len = physts_ie_len_tab[ie];
+	else
+		ie_len = RTW89_GET_PHY_STS_IE_LEN(addr) * VAR_LEN_UNIT;
+
+	return ie_len;
+}
+
+static void rtw89_core_parse_phy_status_ie01(struct rtw89_dev *rtwdev, u8 *addr,
+					     struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	s16 cfo;
+
+	/* sign conversion for S(12,2) */
+	cfo = sign_extend32(RTW89_GET_PHY_STS_IE0_CFO(addr), 11);
+	rtw89_phy_cfo_parse(rtwdev, cfo, phy_ppdu);
+}
+
+static int rtw89_core_process_phy_status_ie(struct rtw89_dev *rtwdev, u8 *addr,
+					    struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	u8 ie;
+
+	ie = RTW89_GET_PHY_STS_IE_TYPE(addr);
+	switch (ie) {
+	case RTW89_PHYSTS_IE01_CMN_OFDM:
+		rtw89_core_parse_phy_status_ie01(rtwdev, addr, phy_ppdu);
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+static void rtw89_core_update_phy_ppdu(struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	s8 *rssi = phy_ppdu->rssi;
+	u8 *buf = phy_ppdu->buf;
+
+	phy_ppdu->rssi_avg = RTW89_GET_PHY_STS_RSSI_AVG(buf);
+	rssi[RF_PATH_A] = RTW89_RSSI_RAW_TO_DBM(RTW89_GET_PHY_STS_RSSI_A(buf));
+	rssi[RF_PATH_B] = RTW89_RSSI_RAW_TO_DBM(RTW89_GET_PHY_STS_RSSI_B(buf));
+	rssi[RF_PATH_C] = RTW89_RSSI_RAW_TO_DBM(RTW89_GET_PHY_STS_RSSI_C(buf));
+	rssi[RF_PATH_D] = RTW89_RSSI_RAW_TO_DBM(RTW89_GET_PHY_STS_RSSI_D(buf));
+}
+
+static int rtw89_core_rx_process_phy_ppdu(struct rtw89_dev *rtwdev,
+					  struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	if (RTW89_GET_PHY_STS_LEN(phy_ppdu->buf) << 3 != phy_ppdu->len) {
+		rtw89_warn(rtwdev, "phy ppdu len mismatch\n");
+		return -EINVAL;
+	}
+	rtw89_core_update_phy_ppdu(phy_ppdu);
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_core_rx_process_phy_ppdu_iter,
+					  phy_ppdu);
+
+	return 0;
+}
+
+static int rtw89_core_rx_parse_phy_sts(struct rtw89_dev *rtwdev,
+				       struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	u16 ie_len;
+	u8 *pos, *end;
+
+	if (!phy_ppdu->to_self)
+		return 0;
+
+	pos = (u8 *)phy_ppdu->buf + PHY_STS_HDR_LEN;
+	end = (u8 *)phy_ppdu->buf + phy_ppdu->len;
+	while (pos < end) {
+		ie_len = rtw89_core_get_phy_status_ie_len(rtwdev, pos);
+		rtw89_core_process_phy_status_ie(rtwdev, pos, phy_ppdu);
+		pos += ie_len;
+		if (pos > end || ie_len == 0) {
+			rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+				    "phy status parse failed\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static void rtw89_core_rx_process_phy_sts(struct rtw89_dev *rtwdev,
+					  struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	int ret;
+
+	ret = rtw89_core_rx_parse_phy_sts(rtwdev, phy_ppdu);
+	if (ret)
+		rtw89_debug(rtwdev, RTW89_DBG_TXRX, "parse phy sts failed\n");
+	else
+		phy_ppdu->valid = true;
+}
+
+static u8 rtw89_rxdesc_to_nl_he_gi(struct rtw89_dev *rtwdev,
+				   const struct rtw89_rx_desc_info *desc_info,
+				   bool rx_status)
+{
+	switch (desc_info->gi_ltf) {
+	case RTW89_GILTF_SGI_4XHE08:
+	case RTW89_GILTF_2XHE08:
+	case RTW89_GILTF_1XHE08:
+		return NL80211_RATE_INFO_HE_GI_0_8;
+	case RTW89_GILTF_2XHE16:
+	case RTW89_GILTF_1XHE16:
+		return NL80211_RATE_INFO_HE_GI_1_6;
+	case RTW89_GILTF_LGI_4XHE32:
+		return NL80211_RATE_INFO_HE_GI_3_2;
+	default:
+		rtw89_warn(rtwdev, "invalid gi_ltf=%d", desc_info->gi_ltf);
+		return rx_status ? NL80211_RATE_INFO_HE_GI_3_2 : U8_MAX;
+	}
+}
+
+static bool rtw89_core_rx_ppdu_match(struct rtw89_dev *rtwdev,
+				     struct rtw89_rx_desc_info *desc_info,
+				     struct ieee80211_rx_status *status)
+{
+	u8 band = desc_info->bb_sel ? RTW89_PHY_1 : RTW89_PHY_0;
+	u8 data_rate_mode, bw, rate_idx = MASKBYTE0, gi_ltf;
+	u16 data_rate;
+	bool ret;
+
+	data_rate = desc_info->data_rate;
+	data_rate_mode = GET_DATA_RATE_MODE(data_rate);
+	if (data_rate_mode == DATA_RATE_MODE_NON_HT) {
+		rate_idx = GET_DATA_RATE_NOT_HT_IDX(data_rate);
+		/* No 4 CCK rates for 5G */
+		if (status->band == NL80211_BAND_5GHZ)
+			rate_idx -= 4;
+	} else if (data_rate_mode == DATA_RATE_MODE_HT) {
+		rate_idx = GET_DATA_RATE_HT_IDX(data_rate);
+	} else if (data_rate_mode == DATA_RATE_MODE_VHT) {
+		rate_idx = GET_DATA_RATE_VHT_HE_IDX(data_rate);
+	} else if (data_rate_mode == DATA_RATE_MODE_HE) {
+		rate_idx = GET_DATA_RATE_VHT_HE_IDX(data_rate);
+	} else {
+		rtw89_warn(rtwdev, "invalid RX rate mode %d\n", data_rate_mode);
+	}
+
+	if (desc_info->bw == RTW89_CHANNEL_WIDTH_80)
+		bw = RATE_INFO_BW_80;
+	else if (desc_info->bw == RTW89_CHANNEL_WIDTH_40)
+		bw = RATE_INFO_BW_40;
+	else
+		bw = RATE_INFO_BW_20;
+
+	gi_ltf = rtw89_rxdesc_to_nl_he_gi(rtwdev, desc_info, false);
+	ret = rtwdev->ppdu_sts.curr_rx_ppdu_cnt[band] == desc_info->ppdu_cnt &&
+	      status->rate_idx == rate_idx &&
+	      status->he_gi == gi_ltf &&
+	      status->bw == bw;
+
+	return ret;
+}
+
+struct rtw89_vif_rx_stats_iter_data {
+	struct rtw89_dev *rtwdev;
+	struct rtw89_rx_phy_ppdu *phy_ppdu;
+	struct rtw89_rx_desc_info *desc_info;
+	struct sk_buff *skb;
+	const u8 *bssid;
+};
+
+static void rtw89_vif_rx_stats_iter(void *data, u8 *mac,
+				    struct ieee80211_vif *vif)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct rtw89_vif_rx_stats_iter_data *iter_data = data;
+	struct rtw89_dev *rtwdev = iter_data->rtwdev;
+	struct rtw89_pkt_stat *pkt_stat = &rtwdev->phystat.cur_pkt_stat;
+	struct rtw89_rx_desc_info *desc_info = iter_data->desc_info;
+	struct sk_buff *skb = iter_data->skb;
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+	const u8 *bssid = iter_data->bssid;
+
+	if (!ether_addr_equal(vif->bss_conf.bssid, bssid))
+		return;
+
+	if (ieee80211_is_beacon(hdr->frame_control))
+		pkt_stat->beacon_nr++;
+
+	if (!ether_addr_equal(vif->addr, hdr->addr1))
+		return;
+
+	if (desc_info->data_rate < RTW89_HW_RATE_NR)
+		pkt_stat->rx_rate_cnt[desc_info->data_rate]++;
+
+	rtw89_traffic_stats_accu(rtwdev, &rtwvif->stats, skb, false);
+}
+
+static void rtw89_core_rx_stats(struct rtw89_dev *rtwdev,
+				struct rtw89_rx_phy_ppdu *phy_ppdu,
+				struct rtw89_rx_desc_info *desc_info,
+				struct sk_buff *skb)
+{
+	struct rtw89_vif_rx_stats_iter_data iter_data;
+
+	rtw89_traffic_stats_accu(rtwdev, &rtwdev->stats, skb, false);
+
+	iter_data.rtwdev = rtwdev;
+	iter_data.phy_ppdu = phy_ppdu;
+	iter_data.desc_info = desc_info;
+	iter_data.skb = skb;
+	iter_data.bssid = get_hdr_bssid((struct ieee80211_hdr *)skb->data);
+	rtw89_iterate_vifs_bh(rtwdev, rtw89_vif_rx_stats_iter, &iter_data);
+}
+
+static void rtw89_core_rx_pending_skb(struct rtw89_dev *rtwdev,
+				      struct rtw89_rx_phy_ppdu *phy_ppdu,
+				      struct rtw89_rx_desc_info *desc_info,
+				      struct sk_buff *skb)
+{
+	u8 band = desc_info->bb_sel ? RTW89_PHY_1 : RTW89_PHY_0;
+	int curr = rtwdev->ppdu_sts.curr_rx_ppdu_cnt[band];
+	struct sk_buff *skb_ppdu = NULL, *tmp;
+	struct ieee80211_rx_status *rx_status;
+
+	if (curr > RTW89_MAX_PPDU_CNT)
+		return;
+
+	skb_queue_walk_safe(&rtwdev->ppdu_sts.rx_queue[band], skb_ppdu, tmp) {
+		skb_unlink(skb_ppdu, &rtwdev->ppdu_sts.rx_queue[band]);
+		rx_status = IEEE80211_SKB_RXCB(skb_ppdu);
+		if (rtw89_core_rx_ppdu_match(rtwdev, desc_info, rx_status))
+			rtw89_chip_query_ppdu(rtwdev, phy_ppdu, rx_status);
+		rtw89_core_rx_stats(rtwdev, phy_ppdu, desc_info, skb_ppdu);
+		ieee80211_rx_napi(rtwdev->hw, NULL, skb_ppdu, &rtwdev->napi);
+		rtwdev->napi_budget_countdown--;
+	}
+}
+
+static void rtw89_core_rx_process_ppdu_sts(struct rtw89_dev *rtwdev,
+					   struct rtw89_rx_desc_info *desc_info,
+					   struct sk_buff *skb)
+{
+	struct rtw89_rx_phy_ppdu phy_ppdu = {.buf = skb->data, .valid = false,
+					     .len = skb->len,
+					     .to_self = desc_info->addr1_match,
+					     .mac_id = desc_info->mac_id};
+	int ret;
+
+	if (desc_info->mac_info_valid)
+		rtw89_core_rx_process_mac_ppdu(rtwdev, skb, &phy_ppdu);
+	ret = rtw89_core_rx_process_phy_ppdu(rtwdev, &phy_ppdu);
+	if (ret)
+		rtw89_debug(rtwdev, RTW89_DBG_TXRX, "process ppdu failed\n");
+
+	rtw89_core_rx_process_phy_sts(rtwdev, &phy_ppdu);
+	rtw89_core_rx_pending_skb(rtwdev, &phy_ppdu, desc_info, skb);
+	dev_kfree_skb_any(skb);
+}
+
+static void rtw89_core_rx_process_report(struct rtw89_dev *rtwdev,
+					 struct rtw89_rx_desc_info *desc_info,
+					 struct sk_buff *skb)
+{
+	switch (desc_info->pkt_type) {
+	case RTW89_CORE_RX_TYPE_C2H:
+		rtw89_fw_c2h_irqsafe(rtwdev, skb);
+		break;
+	case RTW89_CORE_RX_TYPE_PPDU_STAT:
+		rtw89_core_rx_process_ppdu_sts(rtwdev, desc_info, skb);
+		break;
+	default:
+		rtw89_debug(rtwdev, RTW89_DBG_TXRX, "unhandled pkt_type=%d\n",
+			    desc_info->pkt_type);
+		dev_kfree_skb_any(skb);
+		break;
+	}
+}
+
+void rtw89_core_query_rxdesc(struct rtw89_dev *rtwdev,
+			     struct rtw89_rx_desc_info *desc_info,
+			     u8 *data, u32 data_offset)
+{
+	struct rtw89_rxdesc_short *rxd_s;
+	struct rtw89_rxdesc_long *rxd_l;
+	u8 shift_len, drv_info_len;
+
+	rxd_s = (struct rtw89_rxdesc_short *)(data + data_offset);
+	desc_info->pkt_size = RTW89_GET_RXWD_PKT_SIZE(rxd_s);
+	desc_info->drv_info_size = RTW89_GET_RXWD_DRV_INFO_SIZE(rxd_s);
+	desc_info->long_rxdesc = RTW89_GET_RXWD_LONG_RXD(rxd_s);
+	desc_info->pkt_type = RTW89_GET_RXWD_RPKT_TYPE(rxd_s);
+	desc_info->mac_info_valid = RTW89_GET_RXWD_MAC_INFO_VALID(rxd_s);
+	desc_info->bw = RTW89_GET_RXWD_BW(rxd_s);
+	desc_info->data_rate = RTW89_GET_RXWD_DATA_RATE(rxd_s);
+	desc_info->gi_ltf = RTW89_GET_RXWD_GI_LTF(rxd_s);
+	desc_info->user_id = RTW89_GET_RXWD_USER_ID(rxd_s);
+	desc_info->sr_en = RTW89_GET_RXWD_SR_EN(rxd_s);
+	desc_info->ppdu_cnt = RTW89_GET_RXWD_PPDU_CNT(rxd_s);
+	desc_info->ppdu_type = RTW89_GET_RXWD_PPDU_TYPE(rxd_s);
+	desc_info->free_run_cnt = RTW89_GET_RXWD_FREE_RUN_CNT(rxd_s);
+	desc_info->icv_err = RTW89_GET_RXWD_ICV_ERR(rxd_s);
+	desc_info->crc32_err = RTW89_GET_RXWD_CRC32_ERR(rxd_s);
+	desc_info->hw_dec = RTW89_GET_RXWD_HW_DEC(rxd_s);
+	desc_info->sw_dec = RTW89_GET_RXWD_SW_DEC(rxd_s);
+	desc_info->addr1_match = RTW89_GET_RXWD_A1_MATCH(rxd_s);
+
+	shift_len = desc_info->shift << 1; /* 2-byte unit */
+	drv_info_len = desc_info->drv_info_size << 3; /* 8-byte unit */
+	desc_info->offset = data_offset + shift_len + drv_info_len;
+	desc_info->ready = true;
+
+	if (!desc_info->long_rxdesc)
+		return;
+
+	rxd_l = (struct rtw89_rxdesc_long *)(data + data_offset);
+	desc_info->frame_type = RTW89_GET_RXWD_TYPE(rxd_l);
+	desc_info->addr_cam_valid = RTW89_GET_RXWD_ADDR_CAM_VLD(rxd_l);
+	desc_info->addr_cam_id = RTW89_GET_RXWD_ADDR_CAM_ID(rxd_l);
+	desc_info->sec_cam_id = RTW89_GET_RXWD_SEC_CAM_ID(rxd_l);
+	desc_info->mac_id = RTW89_GET_RXWD_MAC_ID(rxd_l);
+	desc_info->rx_pl_id = RTW89_GET_RXWD_RX_PL_ID(rxd_l);
+}
+EXPORT_SYMBOL(rtw89_core_query_rxdesc);
+
+struct rtw89_core_iter_rx_status {
+	struct rtw89_dev *rtwdev;
+	struct ieee80211_rx_status *rx_status;
+	struct rtw89_rx_desc_info *desc_info;
+	u8 mac_id;
+};
+
+static
+void rtw89_core_stats_sta_rx_status_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_core_iter_rx_status *iter_data =
+				(struct rtw89_core_iter_rx_status *)data;
+	struct ieee80211_rx_status *rx_status = iter_data->rx_status;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_rx_desc_info *desc_info = iter_data->desc_info;
+	u8 mac_id = iter_data->mac_id;
+
+	if (mac_id != rtwsta->mac_id)
+		return;
+
+	rtwsta->rx_status = *rx_status;
+	rtwsta->rx_hw_rate = desc_info->data_rate;
+}
+
+static void rtw89_core_stats_sta_rx_status(struct rtw89_dev *rtwdev,
+					   struct rtw89_rx_desc_info *desc_info,
+					   struct ieee80211_rx_status *rx_status)
+{
+	struct rtw89_core_iter_rx_status iter_data;
+
+	if (!desc_info->addr1_match || !desc_info->long_rxdesc)
+		return;
+
+	if (desc_info->frame_type != RTW89_RX_TYPE_DATA)
+		return;
+
+	iter_data.rtwdev = rtwdev;
+	iter_data.rx_status = rx_status;
+	iter_data.desc_info = desc_info;
+	iter_data.mac_id = desc_info->mac_id;
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_core_stats_sta_rx_status_iter,
+					  &iter_data);
+}
+
+static void rtw89_core_update_rx_status(struct rtw89_dev *rtwdev,
+					struct rtw89_rx_desc_info *desc_info,
+					struct ieee80211_rx_status *rx_status)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+	u16 data_rate;
+	u8 data_rate_mode;
+
+	/* currently using single PHY */
+	rx_status->freq = hw->conf.chandef.chan->center_freq;
+	rx_status->band = hw->conf.chandef.chan->band;
+
+	if (desc_info->icv_err || desc_info->crc32_err)
+		rx_status->flag |= RX_FLAG_FAILED_FCS_CRC;
+
+	if (desc_info->hw_dec &&
+	    !(desc_info->sw_dec || desc_info->icv_err))
+		rx_status->flag |= RX_FLAG_DECRYPTED;
+
+	if (desc_info->bw == RTW89_CHANNEL_WIDTH_80)
+		rx_status->bw = RATE_INFO_BW_80;
+	else if (desc_info->bw == RTW89_CHANNEL_WIDTH_40)
+		rx_status->bw = RATE_INFO_BW_40;
+	else
+		rx_status->bw = RATE_INFO_BW_20;
+
+	data_rate = desc_info->data_rate;
+	data_rate_mode = GET_DATA_RATE_MODE(data_rate);
+	if (data_rate_mode == DATA_RATE_MODE_NON_HT) {
+		rx_status->encoding = RX_ENC_LEGACY;
+		rx_status->rate_idx = GET_DATA_RATE_NOT_HT_IDX(data_rate);
+		/* No 4 CCK rates for 5G */
+		if (rx_status->band == NL80211_BAND_5GHZ)
+			rx_status->rate_idx -= 4;
+		if (rtwdev->scanning)
+			rx_status->rate_idx = min_t(u8, rx_status->rate_idx,
+						    ARRAY_SIZE(rtw89_bitrates) - 5);
+	} else if (data_rate_mode == DATA_RATE_MODE_HT) {
+		rx_status->encoding = RX_ENC_HT;
+		rx_status->rate_idx = GET_DATA_RATE_HT_IDX(data_rate);
+		if (desc_info->gi_ltf)
+			rx_status->enc_flags |= RX_ENC_FLAG_SHORT_GI;
+	} else if (data_rate_mode == DATA_RATE_MODE_VHT) {
+		rx_status->encoding = RX_ENC_VHT;
+		rx_status->rate_idx = GET_DATA_RATE_VHT_HE_IDX(data_rate);
+		rx_status->nss = GET_DATA_RATE_NSS(data_rate) + 1;
+		if (desc_info->gi_ltf)
+			rx_status->enc_flags |= RX_ENC_FLAG_SHORT_GI;
+	} else if (data_rate_mode == DATA_RATE_MODE_HE) {
+		rx_status->encoding = RX_ENC_HE;
+		rx_status->rate_idx = GET_DATA_RATE_VHT_HE_IDX(data_rate);
+		rx_status->nss = GET_DATA_RATE_NSS(data_rate) + 1;
+	} else {
+		rtw89_warn(rtwdev, "invalid RX rate mode %d\n", data_rate_mode);
+	}
+
+	/* he_gi is used to match ppdu, so we always fill it. */
+	rx_status->he_gi = rtw89_rxdesc_to_nl_he_gi(rtwdev, desc_info, true);
+	rx_status->flag |= RX_FLAG_MACTIME_START;
+	rx_status->mactime = desc_info->free_run_cnt;
+
+	rtw89_core_stats_sta_rx_status(rtwdev, desc_info, rx_status);
+}
+
+static enum rtw89_ps_mode rtw89_update_ps_mode(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (rtw89_disable_ps_mode || !chip->ps_mode_supported)
+		return RTW89_PS_MODE_NONE;
+
+	if (chip->ps_mode_supported & BIT(RTW89_PS_MODE_PWR_GATED))
+		return RTW89_PS_MODE_PWR_GATED;
+
+	if (chip->ps_mode_supported & BIT(RTW89_PS_MODE_CLK_GATED))
+		return RTW89_PS_MODE_CLK_GATED;
+
+	if (chip->ps_mode_supported & BIT(RTW89_PS_MODE_RFOFF))
+		return RTW89_PS_MODE_RFOFF;
+
+	return RTW89_PS_MODE_NONE;
+}
+
+static void rtw89_core_flush_ppdu_rx_queue(struct rtw89_dev *rtwdev,
+					   struct rtw89_rx_desc_info *desc_info)
+{
+	struct rtw89_ppdu_sts_info *ppdu_sts = &rtwdev->ppdu_sts;
+	u8 band = desc_info->bb_sel ? RTW89_PHY_1 : RTW89_PHY_0;
+	struct sk_buff *skb_ppdu, *tmp;
+
+	skb_queue_walk_safe(&ppdu_sts->rx_queue[band], skb_ppdu, tmp) {
+		skb_unlink(skb_ppdu, &ppdu_sts->rx_queue[band]);
+		rtw89_core_rx_stats(rtwdev, NULL, desc_info, skb_ppdu);
+		ieee80211_rx_napi(rtwdev->hw, NULL, skb_ppdu, &rtwdev->napi);
+		rtwdev->napi_budget_countdown--;
+	}
+}
+
+void rtw89_core_rx(struct rtw89_dev *rtwdev,
+		   struct rtw89_rx_desc_info *desc_info,
+		   struct sk_buff *skb)
+{
+	struct ieee80211_rx_status *rx_status;
+	struct rtw89_ppdu_sts_info *ppdu_sts = &rtwdev->ppdu_sts;
+	u8 ppdu_cnt = desc_info->ppdu_cnt;
+	u8 band = desc_info->bb_sel ? RTW89_PHY_1 : RTW89_PHY_0;
+
+	if (desc_info->pkt_type != RTW89_CORE_RX_TYPE_WIFI) {
+		rtw89_core_rx_process_report(rtwdev, desc_info, skb);
+		return;
+	}
+
+	if (ppdu_sts->curr_rx_ppdu_cnt[band] != ppdu_cnt) {
+		rtw89_core_flush_ppdu_rx_queue(rtwdev, desc_info);
+		ppdu_sts->curr_rx_ppdu_cnt[band] = ppdu_cnt;
+	}
+
+	rx_status = IEEE80211_SKB_RXCB(skb);
+	memset(rx_status, 0, sizeof(*rx_status));
+	rtw89_core_update_rx_status(rtwdev, desc_info, rx_status);
+	if (desc_info->long_rxdesc &&
+	    BIT(desc_info->frame_type) & PPDU_FILTER_BITMAP) {
+		skb_queue_tail(&ppdu_sts->rx_queue[band], skb);
+	} else {
+		rtw89_core_rx_stats(rtwdev, NULL, desc_info, skb);
+		ieee80211_rx_napi(rtwdev->hw, NULL, skb, &rtwdev->napi);
+		rtwdev->napi_budget_countdown--;
+	}
+}
+EXPORT_SYMBOL(rtw89_core_rx);
+
+void rtw89_core_napi_start(struct rtw89_dev *rtwdev)
+{
+	if (test_and_set_bit(RTW89_FLAG_NAPI_RUNNING, rtwdev->flags))
+		return;
+
+	napi_enable(&rtwdev->napi);
+}
+EXPORT_SYMBOL(rtw89_core_napi_start);
+
+void rtw89_core_napi_stop(struct rtw89_dev *rtwdev)
+{
+	if (!test_and_clear_bit(RTW89_FLAG_NAPI_RUNNING, rtwdev->flags))
+		return;
+
+	napi_synchronize(&rtwdev->napi);
+	napi_disable(&rtwdev->napi);
+}
+EXPORT_SYMBOL(rtw89_core_napi_stop);
+
+void rtw89_core_napi_init(struct rtw89_dev *rtwdev)
+{
+	init_dummy_netdev(&rtwdev->netdev);
+	netif_napi_add(&rtwdev->netdev, &rtwdev->napi,
+		       rtwdev->hci.ops->napi_poll, NAPI_POLL_WEIGHT);
+}
+EXPORT_SYMBOL(rtw89_core_napi_init);
+
+void rtw89_core_napi_deinit(struct rtw89_dev *rtwdev)
+{
+	rtw89_core_napi_stop(rtwdev);
+	netif_napi_del(&rtwdev->napi);
+}
+EXPORT_SYMBOL(rtw89_core_napi_deinit);
+
+static void rtw89_core_ba_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev =
+		container_of(work, struct rtw89_dev, ba_work);
+	struct rtw89_txq *rtwtxq, *tmp;
+	int ret;
+
+	spin_lock_bh(&rtwdev->ba_lock);
+	list_for_each_entry_safe(rtwtxq, tmp, &rtwdev->ba_list, list) {
+		struct ieee80211_txq *txq = rtw89_txq_to_txq(rtwtxq);
+		struct ieee80211_sta *sta = txq->sta;
+		struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+		u8 tid = txq->tid;
+
+		if (!sta) {
+			rtw89_warn(rtwdev, "cannot start BA without sta\n");
+			goto skip_ba_work;
+		}
+
+		if (rtwsta->disassoc) {
+			rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+				    "cannot start BA with disassoc sta\n");
+			goto skip_ba_work;
+		}
+
+		ret = ieee80211_start_tx_ba_session(sta, tid, 0);
+		if (ret) {
+			rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+				    "failed to setup BA session for %pM:%2d: %d\n",
+				    sta->addr, tid, ret);
+			if (ret == -EINVAL)
+				set_bit(RTW89_TXQ_F_BLOCK_BA, &rtwtxq->flags);
+		}
+skip_ba_work:
+		list_del_init(&rtwtxq->list);
+	}
+	spin_unlock_bh(&rtwdev->ba_lock);
+}
+
+static void rtw89_core_free_sta_pending_ba(struct rtw89_dev *rtwdev,
+					   struct ieee80211_sta *sta)
+{
+	struct rtw89_txq *rtwtxq, *tmp;
+
+	spin_lock_bh(&rtwdev->ba_lock);
+	list_for_each_entry_safe(rtwtxq, tmp, &rtwdev->ba_list, list) {
+		struct ieee80211_txq *txq = rtw89_txq_to_txq(rtwtxq);
+
+		if (sta == txq->sta)
+			list_del_init(&rtwtxq->list);
+	}
+	spin_unlock_bh(&rtwdev->ba_lock);
+}
+
+static void rtw89_core_txq_check_agg(struct rtw89_dev *rtwdev,
+				     struct rtw89_txq *rtwtxq,
+				     struct sk_buff *skb)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+	struct ieee80211_txq *txq = rtw89_txq_to_txq(rtwtxq);
+	struct ieee80211_sta *sta = txq->sta;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+
+	if (unlikely(skb_get_queue_mapping(skb) == IEEE80211_AC_VO))
+		return;
+
+	if (unlikely(skb->protocol == cpu_to_be16(ETH_P_PAE)))
+		return;
+
+	if (unlikely(!sta))
+		return;
+
+	if (unlikely(test_bit(RTW89_TXQ_F_BLOCK_BA, &rtwtxq->flags)))
+		return;
+
+	if (test_bit(RTW89_TXQ_F_AMPDU, &rtwtxq->flags)) {
+		IEEE80211_SKB_CB(skb)->flags |= IEEE80211_TX_CTL_AMPDU;
+		return;
+	}
+
+	spin_lock_bh(&rtwdev->ba_lock);
+	if (!rtwsta->disassoc && list_empty(&rtwtxq->list)) {
+		list_add_tail(&rtwtxq->list, &rtwdev->ba_list);
+		ieee80211_queue_work(hw, &rtwdev->ba_work);
+	}
+	spin_unlock_bh(&rtwdev->ba_lock);
+}
+
+static void rtw89_core_txq_push(struct rtw89_dev *rtwdev,
+				struct rtw89_txq *rtwtxq,
+				unsigned long frame_cnt,
+				unsigned long byte_cnt)
+{
+	struct ieee80211_txq *txq = rtw89_txq_to_txq(rtwtxq);
+	struct ieee80211_vif *vif = txq->vif;
+	struct ieee80211_sta *sta = txq->sta;
+	struct sk_buff *skb;
+	unsigned long i;
+	int ret;
+
+	for (i = 0; i < frame_cnt; i++) {
+		skb = ieee80211_tx_dequeue_ni(rtwdev->hw, txq);
+		if (!skb) {
+			rtw89_debug(rtwdev, RTW89_DBG_TXRX, "dequeue a NULL skb\n");
+			return;
+		}
+		rtw89_core_txq_check_agg(rtwdev, rtwtxq, skb);
+		ret = rtw89_core_tx_write(rtwdev, vif, sta, skb, NULL);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to push txq: %d\n", ret);
+			ieee80211_free_txskb(rtwdev->hw, skb);
+			break;
+		}
+	}
+}
+
+static u32 rtw89_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev, u8 tid)
+{
+	u8 qsel, ch_dma;
+
+	qsel = rtw89_core_get_qsel(rtwdev, tid);
+	ch_dma = rtw89_core_get_ch_dma(rtwdev, qsel);
+
+	return rtw89_hci_check_and_reclaim_tx_resource(rtwdev, ch_dma);
+}
+
+static bool rtw89_core_txq_agg_wait(struct rtw89_dev *rtwdev,
+				    struct ieee80211_txq *txq,
+				    unsigned long *frame_cnt,
+				    bool *sched_txq, bool *reinvoke)
+{
+	struct rtw89_txq *rtwtxq = (struct rtw89_txq *)txq->drv_priv;
+	struct ieee80211_sta *sta = txq->sta;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+
+	if (!sta || rtwsta->max_agg_wait <= 0)
+		return false;
+
+	if (rtwdev->stats.tx_tfc_lv <= RTW89_TFC_MID)
+		return false;
+
+	if (*frame_cnt > 1) {
+		*frame_cnt -= 1;
+		*sched_txq = true;
+		*reinvoke = true;
+		rtwtxq->wait_cnt = 1;
+		return false;
+	}
+
+	if (*frame_cnt == 1 && rtwtxq->wait_cnt < rtwsta->max_agg_wait) {
+		*reinvoke = true;
+		rtwtxq->wait_cnt++;
+		return true;
+	}
+
+	rtwtxq->wait_cnt = 0;
+	return false;
+}
+
+static void rtw89_core_txq_schedule(struct rtw89_dev *rtwdev, u8 ac, bool *reinvoke)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+	struct ieee80211_txq *txq;
+	struct rtw89_txq *rtwtxq;
+	unsigned long frame_cnt;
+	unsigned long byte_cnt;
+	u32 tx_resource;
+	bool sched_txq;
+
+	ieee80211_txq_schedule_start(hw, ac);
+	while ((txq = ieee80211_next_txq(hw, ac))) {
+		rtwtxq = (struct rtw89_txq *)txq->drv_priv;
+		tx_resource = rtw89_check_and_reclaim_tx_resource(rtwdev, txq->tid);
+		sched_txq = false;
+
+		ieee80211_txq_get_depth(txq, &frame_cnt, &byte_cnt);
+		if (rtw89_core_txq_agg_wait(rtwdev, txq, &frame_cnt, &sched_txq, reinvoke)) {
+			ieee80211_return_txq(hw, txq, true);
+			continue;
+		}
+		frame_cnt = min_t(unsigned long, frame_cnt, tx_resource);
+		rtw89_core_txq_push(rtwdev, rtwtxq, frame_cnt, byte_cnt);
+		ieee80211_return_txq(hw, txq, sched_txq);
+		if (frame_cnt != 0)
+			rtw89_core_tx_kick_off(rtwdev, rtw89_core_get_qsel(rtwdev, txq->tid));
+	}
+	ieee80211_txq_schedule_end(hw, ac);
+}
+
+static void rtw89_core_txq_work(struct work_struct *w)
+{
+	struct rtw89_dev *rtwdev = container_of(w, struct rtw89_dev, txq_work);
+	bool reinvoke = false;
+	u8 ac;
+
+	for (ac = 0; ac < IEEE80211_NUM_ACS; ac++)
+		rtw89_core_txq_schedule(rtwdev, ac, &reinvoke);
+
+	if (reinvoke) {
+		/* reinvoke to process the last frame */
+		mod_delayed_work(rtwdev->txq_wq, &rtwdev->txq_reinvoke_work, 1);
+	}
+}
+
+static void rtw89_core_txq_reinvoke_work(struct work_struct *w)
+{
+	struct rtw89_dev *rtwdev = container_of(w, struct rtw89_dev,
+						txq_reinvoke_work.work);
+
+	queue_work(rtwdev->txq_wq, &rtwdev->txq_work);
+}
+
+static enum rtw89_tfc_lv rtw89_get_traffic_level(struct rtw89_dev *rtwdev,
+						 u32 throughput, u64 cnt)
+{
+	if (cnt < 100)
+		return RTW89_TFC_IDLE;
+	if (throughput > 50)
+		return RTW89_TFC_HIGH;
+	if (throughput > 10)
+		return RTW89_TFC_MID;
+	if (throughput > 2)
+		return RTW89_TFC_LOW;
+	return RTW89_TFC_ULTRA_LOW;
+}
+
+static bool rtw89_traffic_stats_calc(struct rtw89_dev *rtwdev,
+				     struct rtw89_traffic_stats *stats)
+{
+	enum rtw89_tfc_lv tx_tfc_lv = stats->tx_tfc_lv;
+	enum rtw89_tfc_lv rx_tfc_lv = stats->rx_tfc_lv;
+
+	stats->tx_throughput_raw = (u32)(stats->tx_unicast >> RTW89_TP_SHIFT);
+	stats->rx_throughput_raw = (u32)(stats->rx_unicast >> RTW89_TP_SHIFT);
+
+	ewma_tp_add(&stats->tx_ewma_tp, stats->tx_throughput_raw);
+	ewma_tp_add(&stats->rx_ewma_tp, stats->rx_throughput_raw);
+
+	stats->tx_throughput = ewma_tp_read(&stats->tx_ewma_tp);
+	stats->rx_throughput = ewma_tp_read(&stats->rx_ewma_tp);
+	stats->tx_tfc_lv = rtw89_get_traffic_level(rtwdev, stats->tx_throughput,
+						   stats->tx_cnt);
+	stats->rx_tfc_lv = rtw89_get_traffic_level(rtwdev, stats->rx_throughput,
+						   stats->rx_cnt);
+	stats->tx_avg_len = stats->tx_cnt ?
+			    DIV_ROUND_DOWN_ULL(stats->tx_unicast, stats->tx_cnt) : 0;
+	stats->rx_avg_len = stats->rx_cnt ?
+			    DIV_ROUND_DOWN_ULL(stats->rx_unicast, stats->rx_cnt) : 0;
+
+	stats->tx_unicast = 0;
+	stats->rx_unicast = 0;
+	stats->tx_cnt = 0;
+	stats->rx_cnt = 0;
+
+	if (tx_tfc_lv != stats->tx_tfc_lv || rx_tfc_lv != stats->rx_tfc_lv)
+		return true;
+
+	return false;
+}
+
+static bool rtw89_traffic_stats_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_vif *rtwvif;
+	bool tfc_changed;
+
+	tfc_changed = rtw89_traffic_stats_calc(rtwdev, &rtwdev->stats);
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		rtw89_traffic_stats_calc(rtwdev, &rtwvif->stats);
+
+	return tfc_changed;
+}
+
+static void rtw89_vif_enter_lps(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	if (rtwvif->wifi_role != RTW89_WIFI_ROLE_STATION)
+		return;
+
+	if (rtwvif->stats.tx_tfc_lv == RTW89_TFC_IDLE &&
+	    rtwvif->stats.rx_tfc_lv == RTW89_TFC_IDLE)
+		rtw89_enter_lps(rtwdev, rtwvif->mac_id);
+}
+
+static void rtw89_enter_lps_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_vif *rtwvif;
+
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		rtw89_vif_enter_lps(rtwdev, rtwvif);
+}
+
+void rtw89_traffic_stats_init(struct rtw89_dev *rtwdev,
+			      struct rtw89_traffic_stats *stats)
+{
+	stats->tx_unicast = 0;
+	stats->rx_unicast = 0;
+	stats->tx_cnt = 0;
+	stats->rx_cnt = 0;
+	ewma_tp_init(&stats->tx_ewma_tp);
+	ewma_tp_init(&stats->rx_ewma_tp);
+}
+
+static void rtw89_track_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						track_work.work);
+	bool tfc_changed;
+
+	mutex_lock(&rtwdev->mutex);
+
+	if (!test_bit(RTW89_FLAG_RUNNING, rtwdev->flags))
+		goto out;
+
+	ieee80211_queue_delayed_work(rtwdev->hw, &rtwdev->track_work,
+				     RTW89_TRACK_WORK_PERIOD);
+
+	tfc_changed = rtw89_traffic_stats_track(rtwdev);
+	if (rtwdev->scanning)
+		goto out;
+
+	rtw89_leave_lps(rtwdev);
+
+	if (tfc_changed) {
+		rtw89_hci_recalc_int_mit(rtwdev);
+		rtw89_btc_ntfy_wl_sta(rtwdev);
+	}
+	rtw89_mac_bf_monitor_track(rtwdev);
+	rtw89_phy_stat_track(rtwdev);
+	rtw89_phy_env_monitor_track(rtwdev);
+	rtw89_phy_dig(rtwdev);
+	rtw89_chip_rfk_track(rtwdev);
+	rtw89_phy_ra_update(rtwdev);
+	rtw89_phy_cfo_track(rtwdev);
+
+	if (rtwdev->lps_enabled && !rtwdev->btc.lps)
+		rtw89_enter_lps_track(rtwdev);
+
+out:
+	mutex_unlock(&rtwdev->mutex);
+}
+
+u8 rtw89_core_acquire_bit_map(unsigned long *addr, unsigned long size)
+{
+	unsigned long bit;
+
+	bit = find_first_zero_bit(addr, size);
+	if (bit < size)
+		set_bit(bit, addr);
+
+	return bit;
+}
+
+void rtw89_core_release_bit_map(unsigned long *addr, u8 bit)
+{
+	clear_bit(bit, addr);
+}
+
+void rtw89_core_release_all_bits_map(unsigned long *addr, unsigned int nbits)
+{
+	bitmap_zero(addr, nbits);
+}
+
+#define RTW89_TYPE_MAPPING(_type)	\
+	case NL80211_IFTYPE_ ## _type:	\
+		rtwvif->wifi_role = RTW89_WIFI_ROLE_ ## _type;	\
+		break
+void rtw89_vif_type_mapping(struct ieee80211_vif *vif, bool assoc)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	switch (vif->type) {
+	RTW89_TYPE_MAPPING(ADHOC);
+	RTW89_TYPE_MAPPING(STATION);
+	RTW89_TYPE_MAPPING(AP);
+	RTW89_TYPE_MAPPING(MONITOR);
+	RTW89_TYPE_MAPPING(MESH_POINT);
+	default:
+		WARN_ON(1);
+		break;
+	}
+
+	switch (vif->type) {
+	case NL80211_IFTYPE_AP:
+	case NL80211_IFTYPE_MESH_POINT:
+		rtwvif->net_type = RTW89_NET_TYPE_AP_MODE;
+		rtwvif->self_role = RTW89_SELF_ROLE_AP;
+		break;
+	case NL80211_IFTYPE_ADHOC:
+		rtwvif->net_type = RTW89_NET_TYPE_AD_HOC;
+		rtwvif->self_role = RTW89_SELF_ROLE_CLIENT;
+		break;
+	case NL80211_IFTYPE_STATION:
+		if (assoc) {
+			rtwvif->net_type = RTW89_NET_TYPE_INFRA;
+			rtwvif->trigger = vif->bss_conf.he_support;
+		} else {
+			rtwvif->net_type = RTW89_NET_TYPE_NO_LINK;
+			rtwvif->trigger = false;
+		}
+		rtwvif->self_role = RTW89_SELF_ROLE_CLIENT;
+		rtwvif->addr_cam.sec_ent_mode = RTW89_ADDR_CAM_SEC_NORMAL;
+		break;
+	default:
+		WARN_ON(1);
+		break;
+	}
+}
+
+int rtw89_core_sta_add(struct rtw89_dev *rtwdev,
+		       struct ieee80211_vif *vif,
+		       struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	int i;
+
+	rtwsta->rtwvif = rtwvif;
+	rtwsta->prev_rssi = 0;
+
+	for (i = 0; i < ARRAY_SIZE(sta->txq); i++)
+		rtw89_core_txq_init(rtwdev, sta->txq[i]);
+
+	ewma_rssi_init(&rtwsta->avg_rssi);
+
+	if (vif->type == NL80211_IFTYPE_STATION) {
+		rtwvif->mgd.ap = sta;
+		rtw89_btc_ntfy_role_info(rtwdev, rtwvif, rtwsta,
+					 BTC_ROLE_MSTS_STA_CONN_START);
+		rtw89_chip_rfk_channel(rtwdev);
+	}
+
+	return 0;
+}
+
+int rtw89_core_sta_disassoc(struct rtw89_dev *rtwdev,
+			    struct ieee80211_vif *vif,
+			    struct ieee80211_sta *sta)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+
+	rtwdev->total_sta_assoc--;
+	rtwsta->disassoc = true;
+
+	return 0;
+}
+
+int rtw89_core_sta_disconnect(struct rtw89_dev *rtwdev,
+			      struct ieee80211_vif *vif,
+			      struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	int ret;
+
+	rtw89_mac_bf_monitor_calc(rtwdev, sta, true);
+	rtw89_mac_bf_disassoc(rtwdev, vif, sta);
+	rtw89_core_free_sta_pending_ba(rtwdev, sta);
+
+	rtw89_vif_type_mapping(vif, false);
+
+	ret = rtw89_fw_h2c_assoc_cmac_tbl(rtwdev, vif, sta);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c cmac table\n");
+		return ret;
+	}
+
+	ret = rtw89_fw_h2c_join_info(rtwdev, rtwvif, 1);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c join info\n");
+		return ret;
+	}
+
+	/* update cam aid mac_id net_type */
+	rtw89_fw_h2c_cam(rtwdev, rtwvif);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c cam\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+int rtw89_core_sta_assoc(struct rtw89_dev *rtwdev,
+			 struct ieee80211_vif *vif,
+			 struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	int ret;
+
+	rtw89_vif_type_mapping(vif, true);
+
+	ret = rtw89_fw_h2c_assoc_cmac_tbl(rtwdev, vif, sta);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c cmac table\n");
+		return ret;
+	}
+
+	/* for station mode, assign the mac_id from itself */
+	if (vif->type == NL80211_IFTYPE_STATION)
+		rtwsta->mac_id = rtwvif->mac_id;
+
+	ret = rtw89_fw_h2c_join_info(rtwdev, rtwvif, 0);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c join info\n");
+		return ret;
+	}
+
+	/* update cam aid mac_id net_type */
+	rtw89_fw_h2c_cam(rtwdev, rtwvif);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c cam\n");
+		return ret;
+	}
+
+	ret = rtw89_fw_h2c_general_pkt(rtwdev, rtwsta->mac_id);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to send h2c general packet\n");
+		return ret;
+	}
+
+	rtwdev->total_sta_assoc++;
+	rtw89_phy_ra_assoc(rtwdev, sta);
+	rtw89_mac_bf_assoc(rtwdev, vif, sta);
+	rtw89_mac_bf_monitor_calc(rtwdev, sta, false);
+
+	if (vif->type == NL80211_IFTYPE_STATION) {
+		rtw89_btc_ntfy_role_info(rtwdev, rtwvif, rtwsta,
+					 BTC_ROLE_MSTS_STA_CONN_END);
+		rtw89_core_get_no_ul_ofdma_htc(rtwdev, &rtwsta->htc_template);
+	}
+
+	return ret;
+}
+
+int rtw89_core_sta_remove(struct rtw89_dev *rtwdev,
+			  struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+
+	if (vif->type == NL80211_IFTYPE_STATION)
+		rtw89_btc_ntfy_role_info(rtwdev, rtwvif, rtwsta,
+					 BTC_ROLE_MSTS_STA_DIS_CONN);
+
+	return 0;
+}
+
+static void rtw89_init_ht_cap(struct rtw89_dev *rtwdev,
+			      struct ieee80211_sta_ht_cap *ht_cap)
+{
+	static const __le16 highest[RF_PATH_MAX] = {
+		cpu_to_le16(150), cpu_to_le16(300), cpu_to_le16(450), cpu_to_le16(600),
+	};
+	struct rtw89_hal *hal = &rtwdev->hal;
+	u8 nss = hal->rx_nss;
+	int i;
+
+	ht_cap->ht_supported = true;
+	ht_cap->cap = 0;
+	ht_cap->cap |= IEEE80211_HT_CAP_SGI_20 |
+		       IEEE80211_HT_CAP_MAX_AMSDU |
+		       IEEE80211_HT_CAP_TX_STBC |
+		       (1 << IEEE80211_HT_CAP_RX_STBC_SHIFT);
+	ht_cap->cap |= IEEE80211_HT_CAP_LDPC_CODING;
+	ht_cap->cap |= IEEE80211_HT_CAP_SUP_WIDTH_20_40 |
+		       IEEE80211_HT_CAP_DSSSCCK40 |
+		       IEEE80211_HT_CAP_SGI_40;
+	ht_cap->ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K;
+	ht_cap->ampdu_density = IEEE80211_HT_MPDU_DENSITY_NONE;
+	ht_cap->mcs.tx_params = IEEE80211_HT_MCS_TX_DEFINED;
+	for (i = 0; i < nss; i++)
+		ht_cap->mcs.rx_mask[i] = 0xFF;
+	ht_cap->mcs.rx_mask[4] = 0x01;
+	ht_cap->mcs.rx_highest = highest[nss - 1];
+}
+
+static void rtw89_init_vht_cap(struct rtw89_dev *rtwdev,
+			       struct ieee80211_sta_vht_cap *vht_cap)
+{
+	static const __le16 highest[RF_PATH_MAX] = {
+		cpu_to_le16(433), cpu_to_le16(867), cpu_to_le16(1300), cpu_to_le16(1733),
+	};
+	struct rtw89_hal *hal = &rtwdev->hal;
+	u16 tx_mcs_map = 0, rx_mcs_map = 0;
+	u8 sts_cap = 3;
+	int i;
+
+	for (i = 0; i < 8; i++) {
+		if (i < hal->tx_nss)
+			tx_mcs_map |= IEEE80211_VHT_MCS_SUPPORT_0_9 << (i * 2);
+		else
+			tx_mcs_map |= IEEE80211_VHT_MCS_NOT_SUPPORTED << (i * 2);
+		if (i < hal->rx_nss)
+			rx_mcs_map |= IEEE80211_VHT_MCS_SUPPORT_0_9 << (i * 2);
+		else
+			rx_mcs_map |= IEEE80211_VHT_MCS_NOT_SUPPORTED << (i * 2);
+	}
+
+	vht_cap->vht_supported = true;
+	vht_cap->cap = IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454 |
+		       IEEE80211_VHT_CAP_SHORT_GI_80 |
+		       IEEE80211_VHT_CAP_RXSTBC_1 |
+		       IEEE80211_VHT_CAP_HTC_VHT |
+		       IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK |
+		       0;
+	vht_cap->cap |= IEEE80211_VHT_CAP_TXSTBC;
+	vht_cap->cap |= IEEE80211_VHT_CAP_RXLDPC;
+	vht_cap->cap |= IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE |
+			IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE;
+	vht_cap->cap |= sts_cap << IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT;
+	vht_cap->vht_mcs.rx_mcs_map = cpu_to_le16(rx_mcs_map);
+	vht_cap->vht_mcs.tx_mcs_map = cpu_to_le16(tx_mcs_map);
+	vht_cap->vht_mcs.rx_highest = highest[hal->rx_nss - 1];
+	vht_cap->vht_mcs.tx_highest = highest[hal->tx_nss - 1];
+}
+
+#define RTW89_SBAND_IFTYPES_NR 2
+
+static void rtw89_init_he_cap(struct rtw89_dev *rtwdev,
+			      enum nl80211_band band,
+			      struct ieee80211_supported_band *sband)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct ieee80211_sband_iftype_data *iftype_data;
+	bool no_ng16 = (chip->chip_id == RTL8852A && hal->cv == CHIP_CBV) ||
+		       (chip->chip_id == RTL8852B && hal->cv == CHIP_CAV);
+	u16 mcs_map = 0;
+	int i;
+	int nss = hal->rx_nss;
+	int idx = 0;
+
+	iftype_data = kcalloc(RTW89_SBAND_IFTYPES_NR, sizeof(*iftype_data), GFP_KERNEL);
+	if (!iftype_data)
+		return;
+
+	for (i = 0; i < 8; i++) {
+		if (i < nss)
+			mcs_map |= IEEE80211_HE_MCS_SUPPORT_0_11 << (i * 2);
+		else
+			mcs_map |= IEEE80211_HE_MCS_NOT_SUPPORTED << (i * 2);
+	}
+
+	for (i = 0; i < NUM_NL80211_IFTYPES; i++) {
+		struct ieee80211_sta_he_cap *he_cap;
+		u8 *mac_cap_info;
+		u8 *phy_cap_info;
+
+		switch (i) {
+		case NL80211_IFTYPE_STATION:
+		case NL80211_IFTYPE_AP:
+			break;
+		default:
+			continue;
+		}
+
+		if (idx >= RTW89_SBAND_IFTYPES_NR) {
+			rtw89_warn(rtwdev, "run out of iftype_data\n");
+			break;
+		}
+
+		iftype_data[idx].types_mask = BIT(i);
+		he_cap = &iftype_data[idx].he_cap;
+		mac_cap_info = he_cap->he_cap_elem.mac_cap_info;
+		phy_cap_info = he_cap->he_cap_elem.phy_cap_info;
+
+		he_cap->has_he = true;
+		if (i == NL80211_IFTYPE_AP)
+			mac_cap_info[0] = IEEE80211_HE_MAC_CAP0_HTC_HE;
+		if (i == NL80211_IFTYPE_STATION)
+			mac_cap_info[1] = IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US;
+		mac_cap_info[2] = IEEE80211_HE_MAC_CAP2_ALL_ACK |
+				  IEEE80211_HE_MAC_CAP2_BSR;
+		mac_cap_info[3] = IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_EXT_2;
+		if (i == NL80211_IFTYPE_AP)
+			mac_cap_info[3] |= IEEE80211_HE_MAC_CAP3_OMI_CONTROL;
+		mac_cap_info[4] = IEEE80211_HE_MAC_CAP4_OPS |
+				  IEEE80211_HE_MAC_CAP4_AMSDU_IN_AMPDU;
+		if (i == NL80211_IFTYPE_STATION)
+			mac_cap_info[5] = IEEE80211_HE_MAC_CAP5_HT_VHT_TRIG_FRAME_RX;
+		phy_cap_info[0] = IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G |
+				  IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G;
+		phy_cap_info[1] = IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A |
+				  IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD |
+				  IEEE80211_HE_PHY_CAP1_HE_LTF_AND_GI_FOR_HE_PPDUS_0_8US;
+		phy_cap_info[2] = IEEE80211_HE_PHY_CAP2_NDP_4x_LTF_AND_3_2US |
+				  IEEE80211_HE_PHY_CAP2_STBC_TX_UNDER_80MHZ |
+				  IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ |
+				  IEEE80211_HE_PHY_CAP2_DOPPLER_TX;
+		phy_cap_info[3] = IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_16_QAM;
+		if (i == NL80211_IFTYPE_STATION)
+			phy_cap_info[3] |= IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_16_QAM |
+					   IEEE80211_HE_PHY_CAP3_DCM_MAX_TX_NSS_2;
+		if (i == NL80211_IFTYPE_AP)
+			phy_cap_info[3] |= IEEE80211_HE_PHY_CAP3_RX_PARTIAL_BW_SU_IN_20MHZ_MU;
+		phy_cap_info[4] = IEEE80211_HE_PHY_CAP4_SU_BEAMFORMEE |
+				  IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_4;
+		phy_cap_info[5] = no_ng16 ? 0 :
+				  IEEE80211_HE_PHY_CAP5_NG16_SU_FEEDBACK |
+				  IEEE80211_HE_PHY_CAP5_NG16_MU_FEEDBACK;
+		phy_cap_info[6] = IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_42_SU |
+				  IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_75_MU |
+				  IEEE80211_HE_PHY_CAP6_TRIG_SU_BEAMFORMING_FB |
+				  IEEE80211_HE_PHY_CAP6_PARTIAL_BW_EXT_RANGE;
+		phy_cap_info[7] = IEEE80211_HE_PHY_CAP7_POWER_BOOST_FACTOR_SUPP |
+				  IEEE80211_HE_PHY_CAP7_HE_SU_MU_PPDU_4XLTF_AND_08_US_GI |
+				  IEEE80211_HE_PHY_CAP7_MAX_NC_1;
+		phy_cap_info[8] = IEEE80211_HE_PHY_CAP8_HE_ER_SU_PPDU_4XLTF_AND_08_US_GI |
+				  IEEE80211_HE_PHY_CAP8_HE_ER_SU_1XLTF_AND_08_US_GI |
+				  IEEE80211_HE_PHY_CAP8_DCM_MAX_RU_996;
+		phy_cap_info[9] = IEEE80211_HE_PHY_CAP9_LONGER_THAN_16_SIGB_OFDM_SYM |
+				  IEEE80211_HE_PHY_CAP9_RX_1024_QAM_LESS_THAN_242_TONE_RU |
+				  IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_COMP_SIGB |
+				  IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_NON_COMP_SIGB |
+				  IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_16US;
+		if (i == NL80211_IFTYPE_STATION)
+			phy_cap_info[9] |= IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU;
+		he_cap->he_mcs_nss_supp.rx_mcs_80 = cpu_to_le16(mcs_map);
+		he_cap->he_mcs_nss_supp.tx_mcs_80 = cpu_to_le16(mcs_map);
+
+		idx++;
+	}
+
+	sband->iftype_data = iftype_data;
+	sband->n_iftype_data = idx;
+}
+
+static int rtw89_core_set_supported_band(struct rtw89_dev *rtwdev)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+	struct ieee80211_supported_band *sband_2ghz = NULL, *sband_5ghz = NULL;
+	u32 size = sizeof(struct ieee80211_supported_band);
+
+	sband_2ghz = kmemdup(&rtw89_sband_2ghz, size, GFP_KERNEL);
+	if (!sband_2ghz)
+		goto err;
+	rtw89_init_ht_cap(rtwdev, &sband_2ghz->ht_cap);
+	rtw89_init_he_cap(rtwdev, NL80211_BAND_2GHZ, sband_2ghz);
+	hw->wiphy->bands[NL80211_BAND_2GHZ] = sband_2ghz;
+
+	sband_5ghz = kmemdup(&rtw89_sband_5ghz, size, GFP_KERNEL);
+	if (!sband_5ghz)
+		goto err;
+	rtw89_init_ht_cap(rtwdev, &sband_5ghz->ht_cap);
+	rtw89_init_vht_cap(rtwdev, &sband_5ghz->vht_cap);
+	rtw89_init_he_cap(rtwdev, NL80211_BAND_5GHZ, sband_5ghz);
+	hw->wiphy->bands[NL80211_BAND_5GHZ] = sband_5ghz;
+
+	return 0;
+
+err:
+	hw->wiphy->bands[NL80211_BAND_2GHZ] = NULL;
+	hw->wiphy->bands[NL80211_BAND_5GHZ] = NULL;
+	if (sband_2ghz)
+		kfree(sband_2ghz->iftype_data);
+	if (sband_5ghz)
+		kfree(sband_5ghz->iftype_data);
+	kfree(sband_2ghz);
+	kfree(sband_5ghz);
+	return -ENOMEM;
+}
+
+static void rtw89_core_clr_supported_band(struct rtw89_dev *rtwdev)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+
+	kfree(hw->wiphy->bands[NL80211_BAND_2GHZ]->iftype_data);
+	kfree(hw->wiphy->bands[NL80211_BAND_5GHZ]->iftype_data);
+	kfree(hw->wiphy->bands[NL80211_BAND_2GHZ]);
+	kfree(hw->wiphy->bands[NL80211_BAND_5GHZ]);
+	hw->wiphy->bands[NL80211_BAND_2GHZ] = NULL;
+	hw->wiphy->bands[NL80211_BAND_5GHZ] = NULL;
+}
+
+static void rtw89_core_ppdu_sts_init(struct rtw89_dev *rtwdev)
+{
+	int i;
+
+	for (i = 0; i < RTW89_PHY_MAX; i++)
+		skb_queue_head_init(&rtwdev->ppdu_sts.rx_queue[i]);
+	for (i = 0; i < RTW89_PHY_MAX; i++)
+		rtwdev->ppdu_sts.curr_rx_ppdu_cnt[i] = U8_MAX;
+}
+
+int rtw89_core_start(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	rtwdev->mac.qta_mode = RTW89_QTA_SCC;
+	ret = rtw89_mac_init(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "mac init fail, ret:%d\n", ret);
+		return ret;
+	}
+
+	rtw89_btc_ntfy_poweron(rtwdev);
+
+	/* efuse process */
+
+	/* pre-config BB/RF, BB reset/RFC reset */
+	rtw89_mac_disable_bb_rf(rtwdev);
+	rtw89_mac_enable_bb_rf(rtwdev);
+	rtw89_phy_init_bb_reg(rtwdev);
+	rtw89_phy_init_rf_reg(rtwdev);
+
+	rtw89_btc_ntfy_init(rtwdev, BTC_MODE_NORMAL);
+
+	rtw89_phy_dm_init(rtwdev);
+
+	rtw89_mac_cfg_ppdu_status(rtwdev, RTW89_MAC_0, true);
+	rtw89_mac_update_rts_threshold(rtwdev, RTW89_MAC_0);
+
+	ret = rtw89_hci_start(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to start hci\n");
+		return ret;
+	}
+
+	ieee80211_queue_delayed_work(rtwdev->hw, &rtwdev->track_work,
+				     RTW89_TRACK_WORK_PERIOD);
+
+	set_bit(RTW89_FLAG_RUNNING, rtwdev->flags);
+
+	rtw89_btc_ntfy_radio_state(rtwdev, BTC_RFCTRL_WL_ON);
+	rtw89_fw_h2c_fw_log(rtwdev, rtwdev->fw.fw_log_enable);
+
+	return 0;
+}
+
+void rtw89_core_stop(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+
+	/* Prvent to stop twice; enter_ips and ops_stop */
+	if (!test_bit(RTW89_FLAG_RUNNING, rtwdev->flags))
+		return;
+
+	rtw89_btc_ntfy_radio_state(rtwdev, BTC_RFCTRL_WL_OFF);
+
+	clear_bit(RTW89_FLAG_RUNNING, rtwdev->flags);
+
+	mutex_unlock(&rtwdev->mutex);
+
+	cancel_work_sync(&rtwdev->c2h_work);
+	cancel_work_sync(&btc->eapol_notify_work);
+	cancel_work_sync(&btc->arp_notify_work);
+	cancel_work_sync(&btc->dhcp_notify_work);
+	cancel_work_sync(&btc->icmp_notify_work);
+	cancel_delayed_work_sync(&rtwdev->txq_reinvoke_work);
+	cancel_delayed_work_sync(&rtwdev->track_work);
+	cancel_delayed_work_sync(&rtwdev->coex_act1_work);
+	cancel_delayed_work_sync(&rtwdev->coex_bt_devinfo_work);
+	cancel_delayed_work_sync(&rtwdev->coex_rfk_chk_work);
+	cancel_delayed_work_sync(&rtwdev->cfo_track_work);
+
+	mutex_lock(&rtwdev->mutex);
+
+	rtw89_btc_ntfy_poweroff(rtwdev);
+	rtw89_hci_flush_queues(rtwdev, BIT(rtwdev->hw->queues) - 1, true);
+	rtw89_mac_flush_txq(rtwdev, BIT(rtwdev->hw->queues) - 1, true);
+	rtw89_hci_stop(rtwdev);
+	rtw89_hci_deinit(rtwdev);
+	rtw89_mac_pwr_off(rtwdev);
+	rtw89_hci_reset(rtwdev);
+}
+
+int rtw89_core_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	int ret;
+
+	INIT_LIST_HEAD(&rtwdev->ba_list);
+	INIT_LIST_HEAD(&rtwdev->rtwvifs_list);
+	INIT_LIST_HEAD(&rtwdev->early_h2c_list);
+	INIT_WORK(&rtwdev->ba_work, rtw89_core_ba_work);
+	INIT_WORK(&rtwdev->txq_work, rtw89_core_txq_work);
+	INIT_DELAYED_WORK(&rtwdev->txq_reinvoke_work, rtw89_core_txq_reinvoke_work);
+	INIT_DELAYED_WORK(&rtwdev->track_work, rtw89_track_work);
+	INIT_DELAYED_WORK(&rtwdev->coex_act1_work, rtw89_coex_act1_work);
+	INIT_DELAYED_WORK(&rtwdev->coex_bt_devinfo_work, rtw89_coex_bt_devinfo_work);
+	INIT_DELAYED_WORK(&rtwdev->coex_rfk_chk_work, rtw89_coex_rfk_chk_work);
+	INIT_DELAYED_WORK(&rtwdev->cfo_track_work, rtw89_phy_cfo_track_work);
+	rtwdev->txq_wq = alloc_workqueue("rtw89_tx_wq", WQ_UNBOUND | WQ_HIGHPRI, 0);
+	spin_lock_init(&rtwdev->ba_lock);
+	mutex_init(&rtwdev->mutex);
+	mutex_init(&rtwdev->rf_mutex);
+	rtwdev->total_sta_assoc = 0;
+
+	INIT_WORK(&rtwdev->c2h_work, rtw89_fw_c2h_work);
+	skb_queue_head_init(&rtwdev->c2h_queue);
+	rtw89_core_ppdu_sts_init(rtwdev);
+	rtw89_traffic_stats_init(rtwdev, &rtwdev->stats);
+
+	rtwdev->ps_mode = rtw89_update_ps_mode(rtwdev);
+	rtwdev->hal.rx_fltr = DEFAULT_AX_RX_FLTR;
+
+	INIT_WORK(&btc->eapol_notify_work, rtw89_btc_ntfy_eapol_packet_work);
+	INIT_WORK(&btc->arp_notify_work, rtw89_btc_ntfy_arp_packet_work);
+	INIT_WORK(&btc->dhcp_notify_work, rtw89_btc_ntfy_dhcp_packet_work);
+	INIT_WORK(&btc->icmp_notify_work, rtw89_btc_ntfy_icmp_packet_work);
+
+	ret = rtw89_load_firmware(rtwdev);
+	if (ret) {
+		rtw89_warn(rtwdev, "no firmware loaded\n");
+		return ret;
+	}
+	rtw89_ser_init(rtwdev);
+
+	return 0;
+}
+EXPORT_SYMBOL(rtw89_core_init);
+
+void rtw89_core_deinit(struct rtw89_dev *rtwdev)
+{
+	rtw89_ser_deinit(rtwdev);
+	rtw89_unload_firmware(rtwdev);
+	rtw89_fw_free_all_early_h2c(rtwdev);
+
+	destroy_workqueue(rtwdev->txq_wq);
+	mutex_destroy(&rtwdev->rf_mutex);
+	mutex_destroy(&rtwdev->mutex);
+}
+EXPORT_SYMBOL(rtw89_core_deinit);
+
+static void rtw89_read_chip_ver(struct rtw89_dev *rtwdev)
+{
+	u8 cv;
+
+	cv = rtw89_read32_mask(rtwdev, R_AX_SYS_CFG1, B_AX_CHIP_VER_MASK);
+	if (cv <= CHIP_CBV) {
+		if (rtw89_read32(rtwdev, R_AX_GPIO0_7_FUNC_SEL) == RTW89_R32_DEAD)
+			cv = CHIP_CAV;
+		else
+			cv = CHIP_CBV;
+	}
+
+	rtwdev->hal.cv = cv;
+}
+
+static int rtw89_chip_efuse_info_setup(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_mac_partial_init(rtwdev);
+	if (ret)
+		return ret;
+
+	ret = rtw89_parse_efuse_map(rtwdev);
+	if (ret)
+		return ret;
+
+	ret = rtw89_parse_phycap_map(rtwdev);
+	if (ret)
+		return ret;
+
+	ret = rtw89_mac_setup_phycap(rtwdev);
+	if (ret)
+		return ret;
+
+	rtw89_mac_pwr_off(rtwdev);
+
+	return 0;
+}
+
+static int rtw89_chip_board_info_setup(struct rtw89_dev *rtwdev)
+{
+	rtw89_chip_fem_setup(rtwdev);
+
+	return 0;
+}
+
+int rtw89_chip_info_setup(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	rtw89_read_chip_ver(rtwdev);
+
+	ret = rtw89_wait_firmware_completion(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to wait firmware completion\n");
+		return ret;
+	}
+
+	ret = rtw89_fw_recognize(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to recognize firmware\n");
+		return ret;
+	}
+
+	ret = rtw89_chip_efuse_info_setup(rtwdev);
+	if (ret)
+		return ret;
+
+	ret = rtw89_chip_board_info_setup(rtwdev);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+EXPORT_SYMBOL(rtw89_chip_info_setup);
+
+static int rtw89_core_register_hw(struct rtw89_dev *rtwdev)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+	struct rtw89_efuse *efuse = &rtwdev->efuse;
+	int ret;
+	int tx_headroom = IEEE80211_HT_CTL_LEN;
+
+	hw->vif_data_size = sizeof(struct rtw89_vif);
+	hw->sta_data_size = sizeof(struct rtw89_sta);
+	hw->txq_data_size = sizeof(struct rtw89_txq);
+
+	SET_IEEE80211_PERM_ADDR(hw, efuse->addr);
+
+	hw->extra_tx_headroom = tx_headroom;
+	hw->queues = IEEE80211_NUM_ACS;
+	hw->max_rx_aggregation_subframes = RTW89_MAX_RX_AGG_NUM;
+	hw->max_tx_aggregation_subframes = RTW89_MAX_TX_AGG_NUM;
+
+	ieee80211_hw_set(hw, SIGNAL_DBM);
+	ieee80211_hw_set(hw, HAS_RATE_CONTROL);
+	ieee80211_hw_set(hw, MFP_CAPABLE);
+	ieee80211_hw_set(hw, REPORTS_TX_ACK_STATUS);
+	ieee80211_hw_set(hw, AMPDU_AGGREGATION);
+	ieee80211_hw_set(hw, RX_INCLUDES_FCS);
+	ieee80211_hw_set(hw, TX_AMSDU);
+	ieee80211_hw_set(hw, SUPPORT_FAST_XMIT);
+	ieee80211_hw_set(hw, SUPPORTS_AMSDU_IN_AMPDU);
+	ieee80211_hw_set(hw, SUPPORTS_PS);
+	ieee80211_hw_set(hw, SUPPORTS_DYNAMIC_PS);
+
+	hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
+	hw->wiphy->available_antennas_tx = BIT(rtwdev->chip->rf_path_num) - 1;
+	hw->wiphy->available_antennas_rx = BIT(rtwdev->chip->rf_path_num) - 1;
+
+	hw->wiphy->features |= NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR;
+
+	wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CAN_REPLACE_PTK0);
+
+	ret = rtw89_core_set_supported_band(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to set supported band\n");
+		return ret;
+	}
+
+	hw->wiphy->reg_notifier = rtw89_regd_notifier;
+	hw->wiphy->sar_capa = &rtw89_sar_capa;
+
+	ret = ieee80211_register_hw(hw);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to register hw\n");
+		goto err;
+	}
+
+	ret = rtw89_regd_init(rtwdev, rtw89_regd_notifier);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to init regd\n");
+		goto err;
+	}
+
+	return 0;
+
+err:
+	return ret;
+}
+
+static void rtw89_core_unregister_hw(struct rtw89_dev *rtwdev)
+{
+	struct ieee80211_hw *hw = rtwdev->hw;
+
+	ieee80211_unregister_hw(hw);
+	rtw89_core_clr_supported_band(rtwdev);
+}
+
+int rtw89_core_register(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_core_register_hw(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to register core hw\n");
+		return ret;
+	}
+
+	rtw89_debugfs_init(rtwdev);
+
+	return 0;
+}
+EXPORT_SYMBOL(rtw89_core_register);
+
+void rtw89_core_unregister(struct rtw89_dev *rtwdev)
+{
+	rtw89_core_unregister_hw(rtwdev);
+}
+EXPORT_SYMBOL(rtw89_core_unregister);
+
+MODULE_AUTHOR("Realtek Corporation");
+MODULE_DESCRIPTION("Realtek 802.11ax wireless core module");
+MODULE_LICENSE("Dual BSD/GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/core.h
@@ -0,0 +1,3384 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_CORE_H__
+#define __RTW89_CORE_H__
+
+#include <linux/average.h>
+#include <linux/bitfield.h>
+#include <linux/firmware.h>
+#include <linux/iopoll.h>
+#include <linux/workqueue.h>
+#include <net/mac80211.h>
+
+struct rtw89_dev;
+
+extern const struct ieee80211_ops rtw89_ops;
+extern const struct rtw89_chip_info rtw8852a_chip_info;
+
+#define MASKBYTE0 0xff
+#define MASKBYTE1 0xff00
+#define MASKBYTE2 0xff0000
+#define MASKBYTE3 0xff000000
+#define MASKBYTE4 0xff00000000ULL
+#define MASKHWORD 0xffff0000
+#define MASKLWORD 0x0000ffff
+#define MASKDWORD 0xffffffff
+#define RFREG_MASK 0xfffff
+#define INV_RF_DATA 0xffffffff
+
+#define RTW89_TRACK_WORK_PERIOD	round_jiffies_relative(HZ * 2)
+#define CFO_TRACK_MAX_USER 64
+#define MAX_RSSI 110
+#define RSSI_FACTOR 1
+#define RTW89_RSSI_RAW_TO_DBM(rssi) ((s8)((rssi) >> RSSI_FACTOR) - MAX_RSSI)
+#define RTW89_MAX_HW_PORT_NUM 5
+
+#define RTW89_HTC_MASK_VARIANT GENMASK(1, 0)
+#define RTW89_HTC_VARIANT_HE 3
+#define RTW89_HTC_MASK_CTL_ID GENMASK(5, 2)
+#define RTW89_HTC_VARIANT_HE_CID_OM 1
+#define RTW89_HTC_VARIANT_HE_CID_CAS 6
+#define RTW89_HTC_MASK_CTL_INFO GENMASK(31, 6)
+
+#define RTW89_HTC_MASK_HTC_OM_RX_NSS GENMASK(8, 6)
+enum htc_om_channel_width {
+	HTC_OM_CHANNEL_WIDTH_20 = 0,
+	HTC_OM_CHANNEL_WIDTH_40 = 1,
+	HTC_OM_CHANNEL_WIDTH_80 = 2,
+	HTC_OM_CHANNEL_WIDTH_160_OR_80_80 = 3,
+};
+#define RTW89_HTC_MASK_HTC_OM_CH_WIDTH GENMASK(10, 9)
+#define RTW89_HTC_MASK_HTC_OM_UL_MU_DIS BIT(11)
+#define RTW89_HTC_MASK_HTC_OM_TX_NSTS GENMASK(14, 12)
+#define RTW89_HTC_MASK_HTC_OM_ER_SU_DIS BIT(15)
+#define RTW89_HTC_MASK_HTC_OM_DL_MU_MIMO_RR BIT(16)
+#define RTW89_HTC_MASK_HTC_OM_UL_MU_DATA_DIS BIT(17)
+
+enum rtw89_subband {
+	RTW89_CH_2G = 0,
+	RTW89_CH_5G_BAND_1 = 1,
+	/* RTW89_CH_5G_BAND_2 = 2, unused */
+	RTW89_CH_5G_BAND_3 = 3,
+	RTW89_CH_5G_BAND_4 = 4,
+
+	RTW89_SUBBAND_NR,
+};
+
+enum rtw89_hci_type {
+	RTW89_HCI_TYPE_PCIE,
+	RTW89_HCI_TYPE_USB,
+	RTW89_HCI_TYPE_SDIO,
+};
+
+enum rtw89_core_chip_id {
+	RTL8852A,
+	RTL8852B,
+	RTL8852C,
+};
+
+enum rtw89_cv {
+	CHIP_CAV,
+	CHIP_CBV,
+	CHIP_CCV,
+	CHIP_CDV,
+	CHIP_CEV,
+	CHIP_CFV,
+	CHIP_CV_MAX,
+	CHIP_CV_INVALID = CHIP_CV_MAX,
+};
+
+enum rtw89_core_tx_type {
+	RTW89_CORE_TX_TYPE_DATA,
+	RTW89_CORE_TX_TYPE_MGMT,
+	RTW89_CORE_TX_TYPE_FWCMD,
+};
+
+enum rtw89_core_rx_type {
+	RTW89_CORE_RX_TYPE_WIFI		= 0,
+	RTW89_CORE_RX_TYPE_PPDU_STAT	= 1,
+	RTW89_CORE_RX_TYPE_CHAN_INFO	= 2,
+	RTW89_CORE_RX_TYPE_BB_SCOPE	= 3,
+	RTW89_CORE_RX_TYPE_F2P_TXCMD	= 4,
+	RTW89_CORE_RX_TYPE_SS2FW	= 5,
+	RTW89_CORE_RX_TYPE_TX_REPORT	= 6,
+	RTW89_CORE_RX_TYPE_TX_REL_HOST	= 7,
+	RTW89_CORE_RX_TYPE_DFS_REPORT	= 8,
+	RTW89_CORE_RX_TYPE_TX_REL_CPU	= 9,
+	RTW89_CORE_RX_TYPE_C2H		= 10,
+	RTW89_CORE_RX_TYPE_CSI		= 11,
+	RTW89_CORE_RX_TYPE_CQI		= 12,
+};
+
+enum rtw89_txq_flags {
+	RTW89_TXQ_F_AMPDU		= 0,
+	RTW89_TXQ_F_BLOCK_BA		= 1,
+};
+
+enum rtw89_net_type {
+	RTW89_NET_TYPE_NO_LINK		= 0,
+	RTW89_NET_TYPE_AD_HOC		= 1,
+	RTW89_NET_TYPE_INFRA		= 2,
+	RTW89_NET_TYPE_AP_MODE		= 3,
+};
+
+enum rtw89_wifi_role {
+	RTW89_WIFI_ROLE_NONE,
+	RTW89_WIFI_ROLE_STATION,
+	RTW89_WIFI_ROLE_AP,
+	RTW89_WIFI_ROLE_AP_VLAN,
+	RTW89_WIFI_ROLE_ADHOC,
+	RTW89_WIFI_ROLE_ADHOC_MASTER,
+	RTW89_WIFI_ROLE_MESH_POINT,
+	RTW89_WIFI_ROLE_MONITOR,
+	RTW89_WIFI_ROLE_P2P_DEVICE,
+	RTW89_WIFI_ROLE_P2P_CLIENT,
+	RTW89_WIFI_ROLE_P2P_GO,
+	RTW89_WIFI_ROLE_NAN,
+	RTW89_WIFI_ROLE_MLME_MAX
+};
+
+enum rtw89_upd_mode {
+	RTW89_VIF_CREATE,
+	RTW89_VIF_REMOVE,
+	RTW89_VIF_TYPE_CHANGE,
+	RTW89_VIF_INFO_CHANGE,
+	RTW89_VIF_CON_DISCONN
+};
+
+enum rtw89_self_role {
+	RTW89_SELF_ROLE_CLIENT,
+	RTW89_SELF_ROLE_AP,
+	RTW89_SELF_ROLE_AP_CLIENT
+};
+
+enum rtw89_msk_sO_el {
+	RTW89_NO_MSK,
+	RTW89_SMA,
+	RTW89_TMA,
+	RTW89_BSSID
+};
+
+enum rtw89_sch_tx_sel {
+	RTW89_SCH_TX_SEL_ALL,
+	RTW89_SCH_TX_SEL_HIQ,
+	RTW89_SCH_TX_SEL_MG0,
+	RTW89_SCH_TX_SEL_MACID,
+};
+
+/* RTW89_ADDR_CAM_SEC_NONE	: not enabled
+ * RTW89_ADDR_CAM_SEC_ALL_UNI	: 0 - 6 unicast
+ * RTW89_ADDR_CAM_SEC_NORMAL	: 0 - 1 unicast, 2 - 4 group, 5 - 6 BIP
+ * RTW89_ADDR_CAM_SEC_4GROUP	: 0 - 1 unicast, 2 - 5 group, 6 BIP
+ */
+enum rtw89_add_cam_sec_mode {
+	RTW89_ADDR_CAM_SEC_NONE		= 0,
+	RTW89_ADDR_CAM_SEC_ALL_UNI	= 1,
+	RTW89_ADDR_CAM_SEC_NORMAL	= 2,
+	RTW89_ADDR_CAM_SEC_4GROUP	= 3,
+};
+
+enum rtw89_sec_key_type {
+	RTW89_SEC_KEY_TYPE_NONE		= 0,
+	RTW89_SEC_KEY_TYPE_WEP40	= 1,
+	RTW89_SEC_KEY_TYPE_WEP104	= 2,
+	RTW89_SEC_KEY_TYPE_TKIP		= 3,
+	RTW89_SEC_KEY_TYPE_WAPI		= 4,
+	RTW89_SEC_KEY_TYPE_GCMSMS4	= 5,
+	RTW89_SEC_KEY_TYPE_CCMP128	= 6,
+	RTW89_SEC_KEY_TYPE_CCMP256	= 7,
+	RTW89_SEC_KEY_TYPE_GCMP128	= 8,
+	RTW89_SEC_KEY_TYPE_GCMP256	= 9,
+	RTW89_SEC_KEY_TYPE_BIP_CCMP128	= 10,
+};
+
+enum rtw89_port {
+	RTW89_PORT_0 = 0,
+	RTW89_PORT_1 = 1,
+	RTW89_PORT_2 = 2,
+	RTW89_PORT_3 = 3,
+	RTW89_PORT_4 = 4,
+	RTW89_PORT_NUM
+};
+
+enum rtw89_band {
+	RTW89_BAND_2G = 0,
+	RTW89_BAND_5G = 1,
+	RTW89_BAND_MAX,
+};
+
+enum rtw89_hw_rate {
+	RTW89_HW_RATE_CCK1	= 0x0,
+	RTW89_HW_RATE_CCK2	= 0x1,
+	RTW89_HW_RATE_CCK5_5	= 0x2,
+	RTW89_HW_RATE_CCK11	= 0x3,
+	RTW89_HW_RATE_OFDM6	= 0x4,
+	RTW89_HW_RATE_OFDM9	= 0x5,
+	RTW89_HW_RATE_OFDM12	= 0x6,
+	RTW89_HW_RATE_OFDM18	= 0x7,
+	RTW89_HW_RATE_OFDM24	= 0x8,
+	RTW89_HW_RATE_OFDM36	= 0x9,
+	RTW89_HW_RATE_OFDM48	= 0xA,
+	RTW89_HW_RATE_OFDM54	= 0xB,
+	RTW89_HW_RATE_MCS0	= 0x80,
+	RTW89_HW_RATE_MCS1	= 0x81,
+	RTW89_HW_RATE_MCS2	= 0x82,
+	RTW89_HW_RATE_MCS3	= 0x83,
+	RTW89_HW_RATE_MCS4	= 0x84,
+	RTW89_HW_RATE_MCS5	= 0x85,
+	RTW89_HW_RATE_MCS6	= 0x86,
+	RTW89_HW_RATE_MCS7	= 0x87,
+	RTW89_HW_RATE_MCS8	= 0x88,
+	RTW89_HW_RATE_MCS9	= 0x89,
+	RTW89_HW_RATE_MCS10	= 0x8A,
+	RTW89_HW_RATE_MCS11	= 0x8B,
+	RTW89_HW_RATE_MCS12	= 0x8C,
+	RTW89_HW_RATE_MCS13	= 0x8D,
+	RTW89_HW_RATE_MCS14	= 0x8E,
+	RTW89_HW_RATE_MCS15	= 0x8F,
+	RTW89_HW_RATE_MCS16	= 0x90,
+	RTW89_HW_RATE_MCS17	= 0x91,
+	RTW89_HW_RATE_MCS18	= 0x92,
+	RTW89_HW_RATE_MCS19	= 0x93,
+	RTW89_HW_RATE_MCS20	= 0x94,
+	RTW89_HW_RATE_MCS21	= 0x95,
+	RTW89_HW_RATE_MCS22	= 0x96,
+	RTW89_HW_RATE_MCS23	= 0x97,
+	RTW89_HW_RATE_MCS24	= 0x98,
+	RTW89_HW_RATE_MCS25	= 0x99,
+	RTW89_HW_RATE_MCS26	= 0x9A,
+	RTW89_HW_RATE_MCS27	= 0x9B,
+	RTW89_HW_RATE_MCS28	= 0x9C,
+	RTW89_HW_RATE_MCS29	= 0x9D,
+	RTW89_HW_RATE_MCS30	= 0x9E,
+	RTW89_HW_RATE_MCS31	= 0x9F,
+	RTW89_HW_RATE_VHT_NSS1_MCS0	= 0x100,
+	RTW89_HW_RATE_VHT_NSS1_MCS1	= 0x101,
+	RTW89_HW_RATE_VHT_NSS1_MCS2	= 0x102,
+	RTW89_HW_RATE_VHT_NSS1_MCS3	= 0x103,
+	RTW89_HW_RATE_VHT_NSS1_MCS4	= 0x104,
+	RTW89_HW_RATE_VHT_NSS1_MCS5	= 0x105,
+	RTW89_HW_RATE_VHT_NSS1_MCS6	= 0x106,
+	RTW89_HW_RATE_VHT_NSS1_MCS7	= 0x107,
+	RTW89_HW_RATE_VHT_NSS1_MCS8	= 0x108,
+	RTW89_HW_RATE_VHT_NSS1_MCS9	= 0x109,
+	RTW89_HW_RATE_VHT_NSS2_MCS0	= 0x110,
+	RTW89_HW_RATE_VHT_NSS2_MCS1	= 0x111,
+	RTW89_HW_RATE_VHT_NSS2_MCS2	= 0x112,
+	RTW89_HW_RATE_VHT_NSS2_MCS3	= 0x113,
+	RTW89_HW_RATE_VHT_NSS2_MCS4	= 0x114,
+	RTW89_HW_RATE_VHT_NSS2_MCS5	= 0x115,
+	RTW89_HW_RATE_VHT_NSS2_MCS6	= 0x116,
+	RTW89_HW_RATE_VHT_NSS2_MCS7	= 0x117,
+	RTW89_HW_RATE_VHT_NSS2_MCS8	= 0x118,
+	RTW89_HW_RATE_VHT_NSS2_MCS9	= 0x119,
+	RTW89_HW_RATE_VHT_NSS3_MCS0	= 0x120,
+	RTW89_HW_RATE_VHT_NSS3_MCS1	= 0x121,
+	RTW89_HW_RATE_VHT_NSS3_MCS2	= 0x122,
+	RTW89_HW_RATE_VHT_NSS3_MCS3	= 0x123,
+	RTW89_HW_RATE_VHT_NSS3_MCS4	= 0x124,
+	RTW89_HW_RATE_VHT_NSS3_MCS5	= 0x125,
+	RTW89_HW_RATE_VHT_NSS3_MCS6	= 0x126,
+	RTW89_HW_RATE_VHT_NSS3_MCS7	= 0x127,
+	RTW89_HW_RATE_VHT_NSS3_MCS8	= 0x128,
+	RTW89_HW_RATE_VHT_NSS3_MCS9	= 0x129,
+	RTW89_HW_RATE_VHT_NSS4_MCS0	= 0x130,
+	RTW89_HW_RATE_VHT_NSS4_MCS1	= 0x131,
+	RTW89_HW_RATE_VHT_NSS4_MCS2	= 0x132,
+	RTW89_HW_RATE_VHT_NSS4_MCS3	= 0x133,
+	RTW89_HW_RATE_VHT_NSS4_MCS4	= 0x134,
+	RTW89_HW_RATE_VHT_NSS4_MCS5	= 0x135,
+	RTW89_HW_RATE_VHT_NSS4_MCS6	= 0x136,
+	RTW89_HW_RATE_VHT_NSS4_MCS7	= 0x137,
+	RTW89_HW_RATE_VHT_NSS4_MCS8	= 0x138,
+	RTW89_HW_RATE_VHT_NSS4_MCS9	= 0x139,
+	RTW89_HW_RATE_HE_NSS1_MCS0	= 0x180,
+	RTW89_HW_RATE_HE_NSS1_MCS1	= 0x181,
+	RTW89_HW_RATE_HE_NSS1_MCS2	= 0x182,
+	RTW89_HW_RATE_HE_NSS1_MCS3	= 0x183,
+	RTW89_HW_RATE_HE_NSS1_MCS4	= 0x184,
+	RTW89_HW_RATE_HE_NSS1_MCS5	= 0x185,
+	RTW89_HW_RATE_HE_NSS1_MCS6	= 0x186,
+	RTW89_HW_RATE_HE_NSS1_MCS7	= 0x187,
+	RTW89_HW_RATE_HE_NSS1_MCS8	= 0x188,
+	RTW89_HW_RATE_HE_NSS1_MCS9	= 0x189,
+	RTW89_HW_RATE_HE_NSS1_MCS10	= 0x18A,
+	RTW89_HW_RATE_HE_NSS1_MCS11	= 0x18B,
+	RTW89_HW_RATE_HE_NSS2_MCS0	= 0x190,
+	RTW89_HW_RATE_HE_NSS2_MCS1	= 0x191,
+	RTW89_HW_RATE_HE_NSS2_MCS2	= 0x192,
+	RTW89_HW_RATE_HE_NSS2_MCS3	= 0x193,
+	RTW89_HW_RATE_HE_NSS2_MCS4	= 0x194,
+	RTW89_HW_RATE_HE_NSS2_MCS5	= 0x195,
+	RTW89_HW_RATE_HE_NSS2_MCS6	= 0x196,
+	RTW89_HW_RATE_HE_NSS2_MCS7	= 0x197,
+	RTW89_HW_RATE_HE_NSS2_MCS8	= 0x198,
+	RTW89_HW_RATE_HE_NSS2_MCS9	= 0x199,
+	RTW89_HW_RATE_HE_NSS2_MCS10	= 0x19A,
+	RTW89_HW_RATE_HE_NSS2_MCS11	= 0x19B,
+	RTW89_HW_RATE_HE_NSS3_MCS0	= 0x1A0,
+	RTW89_HW_RATE_HE_NSS3_MCS1	= 0x1A1,
+	RTW89_HW_RATE_HE_NSS3_MCS2	= 0x1A2,
+	RTW89_HW_RATE_HE_NSS3_MCS3	= 0x1A3,
+	RTW89_HW_RATE_HE_NSS3_MCS4	= 0x1A4,
+	RTW89_HW_RATE_HE_NSS3_MCS5	= 0x1A5,
+	RTW89_HW_RATE_HE_NSS3_MCS6	= 0x1A6,
+	RTW89_HW_RATE_HE_NSS3_MCS7	= 0x1A7,
+	RTW89_HW_RATE_HE_NSS3_MCS8	= 0x1A8,
+	RTW89_HW_RATE_HE_NSS3_MCS9	= 0x1A9,
+	RTW89_HW_RATE_HE_NSS3_MCS10	= 0x1AA,
+	RTW89_HW_RATE_HE_NSS3_MCS11	= 0x1AB,
+	RTW89_HW_RATE_HE_NSS4_MCS0	= 0x1B0,
+	RTW89_HW_RATE_HE_NSS4_MCS1	= 0x1B1,
+	RTW89_HW_RATE_HE_NSS4_MCS2	= 0x1B2,
+	RTW89_HW_RATE_HE_NSS4_MCS3	= 0x1B3,
+	RTW89_HW_RATE_HE_NSS4_MCS4	= 0x1B4,
+	RTW89_HW_RATE_HE_NSS4_MCS5	= 0x1B5,
+	RTW89_HW_RATE_HE_NSS4_MCS6	= 0x1B6,
+	RTW89_HW_RATE_HE_NSS4_MCS7	= 0x1B7,
+	RTW89_HW_RATE_HE_NSS4_MCS8	= 0x1B8,
+	RTW89_HW_RATE_HE_NSS4_MCS9	= 0x1B9,
+	RTW89_HW_RATE_HE_NSS4_MCS10	= 0x1BA,
+	RTW89_HW_RATE_HE_NSS4_MCS11	= 0x1BB,
+	RTW89_HW_RATE_NR,
+
+	RTW89_HW_RATE_MASK_MOD = GENMASK(8, 7),
+	RTW89_HW_RATE_MASK_VAL = GENMASK(6, 0),
+};
+
+/* 2G channels,
+ * 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
+ */
+#define RTW89_2G_CH_NUM 14
+
+/* 5G channels,
+ * 36, 38, 40, 42, 44, 46, 48, 50,
+ * 52, 54, 56, 58, 60, 62, 64,
+ * 100, 102, 104, 106, 108, 110, 112, 114,
+ * 116, 118, 120, 122, 124, 126, 128, 130,
+ * 132, 134, 136, 138, 140, 142, 144,
+ * 149, 151, 153, 155, 157, 159, 161, 163,
+ * 165, 167, 169, 171, 173, 175, 177
+ */
+#define RTW89_5G_CH_NUM 53
+
+enum rtw89_rate_section {
+	RTW89_RS_CCK,
+	RTW89_RS_OFDM,
+	RTW89_RS_MCS, /* for HT/VHT/HE */
+	RTW89_RS_HEDCM,
+	RTW89_RS_OFFSET,
+	RTW89_RS_MAX,
+	RTW89_RS_LMT_NUM = RTW89_RS_MCS + 1,
+};
+
+enum rtw89_rate_max {
+	RTW89_RATE_CCK_MAX	= 4,
+	RTW89_RATE_OFDM_MAX	= 8,
+	RTW89_RATE_MCS_MAX	= 12,
+	RTW89_RATE_HEDCM_MAX	= 4, /* for HEDCM MCS0/1/3/4 */
+	RTW89_RATE_OFFSET_MAX	= 5, /* for HE(HEDCM)/VHT/HT/OFDM/CCK offset */
+};
+
+enum rtw89_nss {
+	RTW89_NSS_1		= 0,
+	RTW89_NSS_2		= 1,
+	/* HE DCM only support 1ss and 2ss */
+	RTW89_NSS_HEDCM_MAX	= RTW89_NSS_2 + 1,
+	RTW89_NSS_3		= 2,
+	RTW89_NSS_4		= 3,
+	RTW89_NSS_MAX,
+};
+
+enum rtw89_ntx {
+	RTW89_1TX	= 0,
+	RTW89_2TX	= 1,
+	RTW89_NTX_NUM,
+};
+
+enum rtw89_beamforming_type {
+	RTW89_NONBF	= 0,
+	RTW89_BF	= 1,
+	RTW89_BF_NUM,
+};
+
+enum rtw89_regulation_type {
+	RTW89_WW	= 0,
+	RTW89_ETSI	= 1,
+	RTW89_FCC	= 2,
+	RTW89_MKK	= 3,
+	RTW89_NA	= 4,
+	RTW89_IC	= 5,
+	RTW89_KCC	= 6,
+	RTW89_NCC	= 7,
+	RTW89_CHILE	= 8,
+	RTW89_ACMA	= 9,
+	RTW89_MEXICO	= 10,
+	RTW89_UKRAINE	= 11,
+	RTW89_CN	= 12,
+	RTW89_REGD_NUM,
+};
+
+extern const u8 rtw89_rs_idx_max[RTW89_RS_MAX];
+extern const u8 rtw89_rs_nss_max[RTW89_RS_MAX];
+
+struct rtw89_txpwr_byrate {
+	s8 cck[RTW89_RATE_CCK_MAX];
+	s8 ofdm[RTW89_RATE_OFDM_MAX];
+	s8 mcs[RTW89_NSS_MAX][RTW89_RATE_MCS_MAX];
+	s8 hedcm[RTW89_NSS_HEDCM_MAX][RTW89_RATE_HEDCM_MAX];
+	s8 offset[RTW89_RATE_OFFSET_MAX];
+};
+
+enum rtw89_bandwidth_section_num {
+	RTW89_BW20_SEC_NUM = 8,
+	RTW89_BW40_SEC_NUM = 4,
+	RTW89_BW80_SEC_NUM = 2,
+};
+
+struct rtw89_txpwr_limit {
+	s8 cck_20m[RTW89_BF_NUM];
+	s8 cck_40m[RTW89_BF_NUM];
+	s8 ofdm[RTW89_BF_NUM];
+	s8 mcs_20m[RTW89_BW20_SEC_NUM][RTW89_BF_NUM];
+	s8 mcs_40m[RTW89_BW40_SEC_NUM][RTW89_BF_NUM];
+	s8 mcs_80m[RTW89_BW80_SEC_NUM][RTW89_BF_NUM];
+	s8 mcs_160m[RTW89_BF_NUM];
+	s8 mcs_40m_0p5[RTW89_BF_NUM];
+	s8 mcs_40m_2p5[RTW89_BF_NUM];
+};
+
+#define RTW89_RU_SEC_NUM 8
+
+struct rtw89_txpwr_limit_ru {
+	s8 ru26[RTW89_RU_SEC_NUM];
+	s8 ru52[RTW89_RU_SEC_NUM];
+	s8 ru106[RTW89_RU_SEC_NUM];
+};
+
+struct rtw89_rate_desc {
+	enum rtw89_nss nss;
+	enum rtw89_rate_section rs;
+	u8 idx;
+};
+
+#define PHY_STS_HDR_LEN 8
+#define RF_PATH_MAX 4
+#define RTW89_MAX_PPDU_CNT 8
+struct rtw89_rx_phy_ppdu {
+	u8 *buf;
+	u32 len;
+	u8 rssi_avg;
+	s8 rssi[RF_PATH_MAX];
+	u8 mac_id;
+	bool to_self;
+	bool valid;
+};
+
+enum rtw89_mac_idx {
+	RTW89_MAC_0 = 0,
+	RTW89_MAC_1 = 1,
+};
+
+enum rtw89_phy_idx {
+	RTW89_PHY_0 = 0,
+	RTW89_PHY_1 = 1,
+	RTW89_PHY_MAX
+};
+
+enum rtw89_rf_path {
+	RF_PATH_A = 0,
+	RF_PATH_B = 1,
+	RF_PATH_C = 2,
+	RF_PATH_D = 3,
+	RF_PATH_AB,
+	RF_PATH_AC,
+	RF_PATH_AD,
+	RF_PATH_BC,
+	RF_PATH_BD,
+	RF_PATH_CD,
+	RF_PATH_ABC,
+	RF_PATH_ABD,
+	RF_PATH_ACD,
+	RF_PATH_BCD,
+	RF_PATH_ABCD,
+};
+
+enum rtw89_rf_path_bit {
+	RF_A	= BIT(0),
+	RF_B	= BIT(1),
+	RF_C	= BIT(2),
+	RF_D	= BIT(3),
+
+	RF_AB	= (RF_A | RF_B),
+	RF_AC	= (RF_A | RF_C),
+	RF_AD	= (RF_A | RF_D),
+	RF_BC	= (RF_B | RF_C),
+	RF_BD	= (RF_B | RF_D),
+	RF_CD	= (RF_C | RF_D),
+
+	RF_ABC	= (RF_A | RF_B | RF_C),
+	RF_ABD	= (RF_A | RF_B | RF_D),
+	RF_ACD	= (RF_A | RF_C | RF_D),
+	RF_BCD	= (RF_B | RF_C | RF_D),
+
+	RF_ABCD	= (RF_A | RF_B | RF_C | RF_D),
+};
+
+enum rtw89_bandwidth {
+	RTW89_CHANNEL_WIDTH_20	= 0,
+	RTW89_CHANNEL_WIDTH_40	= 1,
+	RTW89_CHANNEL_WIDTH_80	= 2,
+	RTW89_CHANNEL_WIDTH_160	= 3,
+	RTW89_CHANNEL_WIDTH_80_80	= 4,
+	RTW89_CHANNEL_WIDTH_5	= 5,
+	RTW89_CHANNEL_WIDTH_10	= 6,
+};
+
+enum rtw89_ps_mode {
+	RTW89_PS_MODE_NONE	= 0,
+	RTW89_PS_MODE_RFOFF	= 1,
+	RTW89_PS_MODE_CLK_GATED	= 2,
+	RTW89_PS_MODE_PWR_GATED	= 3,
+};
+
+#define RTW89_MAX_CHANNEL_WIDTH RTW89_CHANNEL_WIDTH_80
+#define RTW89_2G_BW_NUM (RTW89_CHANNEL_WIDTH_40 + 1)
+#define RTW89_5G_BW_NUM (RTW89_CHANNEL_WIDTH_80 + 1)
+#define RTW89_PPE_BW_NUM (RTW89_CHANNEL_WIDTH_80 + 1)
+
+enum rtw89_ru_bandwidth {
+	RTW89_RU26 = 0,
+	RTW89_RU52 = 1,
+	RTW89_RU106 = 2,
+	RTW89_RU_NUM,
+};
+
+enum rtw89_sc_offset {
+	RTW89_SC_DONT_CARE	= 0,
+	RTW89_SC_20_UPPER	= 1,
+	RTW89_SC_20_LOWER	= 2,
+	RTW89_SC_20_UPMOST	= 3,
+	RTW89_SC_20_LOWEST	= 4,
+	RTW89_SC_40_UPPER	= 9,
+	RTW89_SC_40_LOWER	= 10,
+};
+
+struct rtw89_channel_params {
+	u8 center_chan;
+	u8 primary_chan;
+	u8 bandwidth;
+	u8 pri_ch_idx;
+	u8 cch_by_bw[RTW89_MAX_CHANNEL_WIDTH + 1];
+};
+
+struct rtw89_channel_help_params {
+	u16 tx_en;
+};
+
+struct rtw89_port_reg {
+	u32 port_cfg;
+	u32 tbtt_prohib;
+	u32 bcn_area;
+	u32 bcn_early;
+	u32 tbtt_early;
+	u32 tbtt_agg;
+	u32 bcn_space;
+	u32 bcn_forcetx;
+	u32 bcn_err_cnt;
+	u32 bcn_err_flag;
+	u32 dtim_ctrl;
+	u32 tbtt_shift;
+	u32 bcn_cnt_tmr;
+	u32 tsftr_l;
+	u32 tsftr_h;
+};
+
+struct rtw89_txwd_body {
+	__le32 dword0;
+	__le32 dword1;
+	__le32 dword2;
+	__le32 dword3;
+	__le32 dword4;
+	__le32 dword5;
+} __packed;
+
+struct rtw89_txwd_info {
+	__le32 dword0;
+	__le32 dword1;
+	__le32 dword2;
+	__le32 dword3;
+	__le32 dword4;
+	__le32 dword5;
+} __packed;
+
+struct rtw89_rx_desc_info {
+	u16 pkt_size;
+	u8 pkt_type;
+	u8 drv_info_size;
+	u8 shift;
+	u8 wl_hd_iv_len;
+	bool long_rxdesc;
+	bool bb_sel;
+	bool mac_info_valid;
+	u16 data_rate;
+	u8 gi_ltf;
+	u8 bw;
+	u32 free_run_cnt;
+	u8 user_id;
+	bool sr_en;
+	u8 ppdu_cnt;
+	u8 ppdu_type;
+	bool icv_err;
+	bool crc32_err;
+	bool hw_dec;
+	bool sw_dec;
+	bool addr1_match;
+	u8 frag;
+	u16 seq;
+	u8 frame_type;
+	u8 rx_pl_id;
+	bool addr_cam_valid;
+	u8 addr_cam_id;
+	u8 sec_cam_id;
+	u8 mac_id;
+	u16 offset;
+	bool ready;
+};
+
+struct rtw89_rxdesc_short {
+	__le32 dword0;
+	__le32 dword1;
+	__le32 dword2;
+	__le32 dword3;
+} __packed;
+
+struct rtw89_rxdesc_long {
+	__le32 dword0;
+	__le32 dword1;
+	__le32 dword2;
+	__le32 dword3;
+	__le32 dword4;
+	__le32 dword5;
+	__le32 dword6;
+	__le32 dword7;
+} __packed;
+
+struct rtw89_tx_desc_info {
+	u16 pkt_size;
+	u8 wp_offset;
+	u8 qsel;
+	u8 ch_dma;
+	u8 hdr_llc_len;
+	bool is_bmc;
+	bool en_wd_info;
+	bool wd_page;
+	bool use_rate;
+	bool dis_data_fb;
+	bool tid_indicate;
+	bool agg_en;
+	bool bk;
+	u8 ampdu_density;
+	u8 ampdu_num;
+	bool sec_en;
+	u8 sec_type;
+	u8 sec_cam_idx;
+	u16 data_rate;
+	u16 data_retry_lowest_rate;
+	bool fw_dl;
+	u16 seq;
+	bool a_ctrl_bsr;
+};
+
+struct rtw89_core_tx_request {
+	enum rtw89_core_tx_type tx_type;
+
+	struct sk_buff *skb;
+	struct ieee80211_vif *vif;
+	struct ieee80211_sta *sta;
+	struct rtw89_tx_desc_info desc_info;
+};
+
+struct rtw89_txq {
+	struct list_head list;
+	unsigned long flags;
+	int wait_cnt;
+};
+
+struct rtw89_mac_ax_gnt {
+	u8 gnt_bt_sw_en;
+	u8 gnt_bt;
+	u8 gnt_wl_sw_en;
+	u8 gnt_wl;
+};
+
+#define RTW89_MAC_AX_COEX_GNT_NR 2
+struct rtw89_mac_ax_coex_gnt {
+	struct rtw89_mac_ax_gnt band[RTW89_MAC_AX_COEX_GNT_NR];
+};
+
+enum rtw89_btc_ncnt {
+	BTC_NCNT_POWER_ON = 0x0,
+	BTC_NCNT_POWER_OFF,
+	BTC_NCNT_INIT_COEX,
+	BTC_NCNT_SCAN_START,
+	BTC_NCNT_SCAN_FINISH,
+	BTC_NCNT_SPECIAL_PACKET,
+	BTC_NCNT_SWITCH_BAND,
+	BTC_NCNT_RFK_TIMEOUT,
+	BTC_NCNT_SHOW_COEX_INFO,
+	BTC_NCNT_ROLE_INFO,
+	BTC_NCNT_CONTROL,
+	BTC_NCNT_RADIO_STATE,
+	BTC_NCNT_CUSTOMERIZE,
+	BTC_NCNT_WL_RFK,
+	BTC_NCNT_WL_STA,
+	BTC_NCNT_FWINFO,
+	BTC_NCNT_TIMER,
+	BTC_NCNT_NUM
+};
+
+enum rtw89_btc_btinfo {
+	BTC_BTINFO_L0 = 0,
+	BTC_BTINFO_L1,
+	BTC_BTINFO_L2,
+	BTC_BTINFO_L3,
+	BTC_BTINFO_H0,
+	BTC_BTINFO_H1,
+	BTC_BTINFO_H2,
+	BTC_BTINFO_H3,
+	BTC_BTINFO_MAX
+};
+
+enum rtw89_btc_dcnt {
+	BTC_DCNT_RUN = 0x0,
+	BTC_DCNT_CX_RUNINFO,
+	BTC_DCNT_RPT,
+	BTC_DCNT_RPT_FREEZE,
+	BTC_DCNT_CYCLE,
+	BTC_DCNT_CYCLE_FREEZE,
+	BTC_DCNT_W1,
+	BTC_DCNT_W1_FREEZE,
+	BTC_DCNT_B1,
+	BTC_DCNT_B1_FREEZE,
+	BTC_DCNT_TDMA_NONSYNC,
+	BTC_DCNT_SLOT_NONSYNC,
+	BTC_DCNT_BTCNT_FREEZE,
+	BTC_DCNT_WL_SLOT_DRIFT,
+	BTC_DCNT_WL_STA_LAST,
+	BTC_DCNT_NUM,
+};
+
+enum rtw89_btc_wl_state_cnt {
+	BTC_WCNT_SCANAP = 0x0,
+	BTC_WCNT_DHCP,
+	BTC_WCNT_EAPOL,
+	BTC_WCNT_ARP,
+	BTC_WCNT_SCBDUPDATE,
+	BTC_WCNT_RFK_REQ,
+	BTC_WCNT_RFK_GO,
+	BTC_WCNT_RFK_REJECT,
+	BTC_WCNT_RFK_TIMEOUT,
+	BTC_WCNT_CH_UPDATE,
+	BTC_WCNT_NUM
+};
+
+enum rtw89_btc_bt_state_cnt {
+	BTC_BCNT_RETRY = 0x0,
+	BTC_BCNT_REINIT,
+	BTC_BCNT_REENABLE,
+	BTC_BCNT_SCBDREAD,
+	BTC_BCNT_RELINK,
+	BTC_BCNT_IGNOWL,
+	BTC_BCNT_INQPAG,
+	BTC_BCNT_INQ,
+	BTC_BCNT_PAGE,
+	BTC_BCNT_ROLESW,
+	BTC_BCNT_AFH,
+	BTC_BCNT_INFOUPDATE,
+	BTC_BCNT_INFOSAME,
+	BTC_BCNT_SCBDUPDATE,
+	BTC_BCNT_HIPRI_TX,
+	BTC_BCNT_HIPRI_RX,
+	BTC_BCNT_LOPRI_TX,
+	BTC_BCNT_LOPRI_RX,
+	BTC_BCNT_RATECHG,
+	BTC_BCNT_NUM
+};
+
+enum rtw89_btc_bt_profile {
+	BTC_BT_NOPROFILE = 0,
+	BTC_BT_HFP = BIT(0),
+	BTC_BT_HID = BIT(1),
+	BTC_BT_A2DP = BIT(2),
+	BTC_BT_PAN = BIT(3),
+	BTC_PROFILE_MAX = 4,
+};
+
+struct rtw89_btc_ant_info {
+	u8 type;  /* shared, dedicated */
+	u8 num;
+	u8 isolation;
+
+	u8 single_pos: 1;/* Single antenna at S0 or S1 */
+	u8 diversity: 1;
+};
+
+enum rtw89_tfc_dir {
+	RTW89_TFC_UL,
+	RTW89_TFC_DL,
+};
+
+struct rtw89_btc_wl_smap {
+	u32 busy: 1;
+	u32 scan: 1;
+	u32 connecting: 1;
+	u32 roaming: 1;
+	u32 _4way: 1;
+	u32 rf_off: 1;
+	u32 lps: 1;
+	u32 ips: 1;
+	u32 init_ok: 1;
+	u32 traffic_dir : 2;
+	u32 rf_off_pre: 1;
+	u32 lps_pre: 1;
+};
+
+enum rtw89_tfc_lv {
+	RTW89_TFC_IDLE,
+	RTW89_TFC_ULTRA_LOW,
+	RTW89_TFC_LOW,
+	RTW89_TFC_MID,
+	RTW89_TFC_HIGH,
+};
+
+#define RTW89_TP_SHIFT 18 /* bytes/2s --> Mbps */
+DECLARE_EWMA(tp, 10, 2);
+
+struct rtw89_traffic_stats {
+	/* units in bytes */
+	u64 tx_unicast;
+	u64 rx_unicast;
+	u32 tx_avg_len;
+	u32 rx_avg_len;
+
+	/* count for packets */
+	u64 tx_cnt;
+	u64 rx_cnt;
+
+	/* units in Mbps */
+	u32 tx_throughput;
+	u32 rx_throughput;
+	u32 tx_throughput_raw;
+	u32 rx_throughput_raw;
+	enum rtw89_tfc_lv tx_tfc_lv;
+	enum rtw89_tfc_lv rx_tfc_lv;
+	struct ewma_tp tx_ewma_tp;
+	struct ewma_tp rx_ewma_tp;
+
+	u16 tx_rate;
+	u16 rx_rate;
+};
+
+struct rtw89_btc_statistic {
+	u8 rssi; /* 0%~110% (dBm = rssi -110) */
+	struct rtw89_traffic_stats traffic;
+};
+
+#define BTC_WL_RSSI_THMAX 4
+
+struct rtw89_btc_wl_link_info {
+	struct rtw89_btc_statistic stat;
+	enum rtw89_tfc_dir dir;
+	u8 rssi_state[BTC_WL_RSSI_THMAX];
+	u8 mac_addr[ETH_ALEN];
+	u8 busy;
+	u8 ch;
+	u8 bw;
+	u8 band;
+	u8 role;
+	u8 pid;
+	u8 phy;
+	u8 dtim_period;
+	u8 mode;
+
+	u8 mac_id;
+	u8 tx_retry;
+
+	u32 bcn_period;
+	u32 busy_t;
+	u32 tx_time;
+	u32 client_cnt;
+	u32 rx_rate_drop_cnt;
+
+	u32 active: 1;
+	u32 noa: 1;
+	u32 client_ps: 1;
+	u32 connected: 2;
+};
+
+union rtw89_btc_wl_state_map {
+	u32 val;
+	struct rtw89_btc_wl_smap map;
+};
+
+struct rtw89_btc_bt_hfp_desc {
+	u32 exist: 1;
+	u32 type: 2;
+	u32 rsvd: 29;
+};
+
+struct rtw89_btc_bt_hid_desc {
+	u32 exist: 1;
+	u32 slot_info: 2;
+	u32 pair_cnt: 2;
+	u32 type: 8;
+	u32 rsvd: 19;
+};
+
+struct rtw89_btc_bt_a2dp_desc {
+	u8 exist: 1;
+	u8 exist_last: 1;
+	u8 play_latency: 1;
+	u8 type: 3;
+	u8 active: 1;
+	u8 sink: 1;
+
+	u8 bitpool;
+	u16 vendor_id;
+	u32 device_name;
+	u32 flush_time;
+};
+
+struct rtw89_btc_bt_pan_desc {
+	u32 exist: 1;
+	u32 type: 1;
+	u32 active: 1;
+	u32 rsvd: 29;
+};
+
+struct rtw89_btc_bt_rfk_info {
+	u32 run: 1;
+	u32 req: 1;
+	u32 timeout: 1;
+	u32 rsvd: 29;
+};
+
+union rtw89_btc_bt_rfk_info_map {
+	u32 val;
+	struct rtw89_btc_bt_rfk_info map;
+};
+
+struct rtw89_btc_bt_ver_info {
+	u32 fw_coex; /* match with which coex_ver */
+	u32 fw;
+};
+
+struct rtw89_btc_bool_sta_chg {
+	u32 now: 1;
+	u32 last: 1;
+	u32 remain: 1;
+	u32 srvd: 29;
+};
+
+struct rtw89_btc_u8_sta_chg {
+	u8 now;
+	u8 last;
+	u8 remain;
+	u8 rsvd;
+};
+
+struct rtw89_btc_wl_scan_info {
+	u8 band[RTW89_PHY_MAX];
+	u8 phy_map;
+	u8 rsvd;
+};
+
+struct rtw89_btc_wl_dbcc_info {
+	u8 op_band[RTW89_PHY_MAX]; /* op band in each phy */
+	u8 scan_band[RTW89_PHY_MAX]; /* scan band in  each phy */
+	u8 real_band[RTW89_PHY_MAX];
+	u8 role[RTW89_PHY_MAX]; /* role in each phy */
+};
+
+struct rtw89_btc_wl_active_role {
+	u8 connected: 1;
+	u8 pid: 3;
+	u8 phy: 1;
+	u8 noa: 1;
+	u8 band: 2;
+
+	u8 client_ps: 1;
+	u8 bw: 7;
+
+	u8 role;
+	u8 ch;
+
+	u16 tx_lvl;
+	u16 rx_lvl;
+	u16 tx_rate;
+	u16 rx_rate;
+};
+
+struct rtw89_btc_wl_role_info_bpos {
+	u16 none: 1;
+	u16 station: 1;
+	u16 ap: 1;
+	u16 vap: 1;
+	u16 adhoc: 1;
+	u16 adhoc_master: 1;
+	u16 mesh: 1;
+	u16 moniter: 1;
+	u16 p2p_device: 1;
+	u16 p2p_gc: 1;
+	u16 p2p_go: 1;
+	u16 nan: 1;
+};
+
+union rtw89_btc_wl_role_info_map {
+	u16 val;
+	struct rtw89_btc_wl_role_info_bpos role;
+};
+
+struct rtw89_btc_wl_role_info { /* struct size must be n*4 bytes */
+	u8 connect_cnt;
+	u8 link_mode;
+	union rtw89_btc_wl_role_info_map role_map;
+	struct rtw89_btc_wl_active_role active_role[RTW89_MAX_HW_PORT_NUM];
+};
+
+struct rtw89_btc_wl_ver_info {
+	u32 fw_coex; /* match with which coex_ver */
+	u32 fw;
+	u32 mac;
+	u32 bb;
+	u32 rf;
+};
+
+struct rtw89_btc_wl_afh_info {
+	u8 en;
+	u8 ch;
+	u8 bw;
+	u8 rsvd;
+} __packed;
+
+struct rtw89_btc_wl_rfk_info {
+	u32 state: 2;
+	u32 path_map: 4;
+	u32 phy_map: 2;
+	u32 band: 2;
+	u32 type: 8;
+	u32 rsvd: 14;
+};
+
+struct rtw89_btc_bt_smap {
+	u32 connect: 1;
+	u32 ble_connect: 1;
+	u32 acl_busy: 1;
+	u32 sco_busy: 1;
+	u32 mesh_busy: 1;
+	u32 inq_pag: 1;
+};
+
+union rtw89_btc_bt_state_map {
+	u32 val;
+	struct rtw89_btc_bt_smap map;
+};
+
+#define BTC_BT_RSSI_THMAX 4
+#define BTC_BT_AFH_GROUP 12
+
+struct rtw89_btc_bt_link_info {
+	struct rtw89_btc_u8_sta_chg profile_cnt;
+	struct rtw89_btc_bool_sta_chg multi_link;
+	struct rtw89_btc_bool_sta_chg relink;
+	struct rtw89_btc_bt_hfp_desc hfp_desc;
+	struct rtw89_btc_bt_hid_desc hid_desc;
+	struct rtw89_btc_bt_a2dp_desc a2dp_desc;
+	struct rtw89_btc_bt_pan_desc pan_desc;
+	union rtw89_btc_bt_state_map status;
+
+	u8 sut_pwr_level[BTC_PROFILE_MAX];
+	u8 golden_rx_shift[BTC_PROFILE_MAX];
+	u8 rssi_state[BTC_BT_RSSI_THMAX];
+	u8 afh_map[BTC_BT_AFH_GROUP];
+
+	u32 role_sw: 1;
+	u32 slave_role: 1;
+	u32 afh_update: 1;
+	u32 cqddr: 1;
+	u32 rssi: 8;
+	u32 tx_3m: 1;
+	u32 rsvd: 19;
+};
+
+struct rtw89_btc_3rdcx_info {
+	u8 type;   /* 0: none, 1:zigbee, 2:LTE  */
+	u8 hw_coex;
+	u16 rsvd;
+};
+
+struct rtw89_btc_dm_emap {
+	u32 init: 1;
+	u32 pta_owner: 1;
+	u32 wl_rfk_timeout: 1;
+	u32 bt_rfk_timeout: 1;
+
+	u32 wl_fw_hang: 1;
+	u32 offload_mismatch: 1;
+	u32 cycle_hang: 1;
+	u32 w1_hang: 1;
+
+	u32 b1_hang: 1;
+	u32 tdma_no_sync: 1;
+	u32 wl_slot_drift: 1;
+};
+
+union rtw89_btc_dm_error_map {
+	u32 val;
+	struct rtw89_btc_dm_emap map;
+};
+
+struct rtw89_btc_rf_para {
+	u32 tx_pwr_freerun;
+	u32 rx_gain_freerun;
+	u32 tx_pwr_perpkt;
+	u32 rx_gain_perpkt;
+};
+
+struct rtw89_btc_wl_info {
+	struct rtw89_btc_wl_link_info link_info[RTW89_MAX_HW_PORT_NUM];
+	struct rtw89_btc_wl_rfk_info rfk_info;
+	struct rtw89_btc_wl_ver_info  ver_info;
+	struct rtw89_btc_wl_afh_info afh_info;
+	struct rtw89_btc_wl_role_info role_info;
+	struct rtw89_btc_wl_scan_info scan_info;
+	struct rtw89_btc_wl_dbcc_info dbcc_info;
+	struct rtw89_btc_rf_para rf_para;
+	union rtw89_btc_wl_state_map status;
+
+	u8 port_id[RTW89_WIFI_ROLE_MLME_MAX];
+	u8 rssi_level;
+
+	u32 scbd;
+};
+
+struct rtw89_btc_module {
+	struct rtw89_btc_ant_info ant;
+	u8 rfe_type;
+	u8 cv;
+
+	u8 bt_solo: 1;
+	u8 bt_pos: 1;
+	u8 switch_type: 1;
+
+	u8 rsvd;
+};
+
+#define RTW89_BTC_DM_MAXSTEP 30
+#define RTW89_BTC_DM_CNT_MAX (RTW89_BTC_DM_MAXSTEP * 8)
+
+struct rtw89_btc_dm_step {
+	u16 step[RTW89_BTC_DM_MAXSTEP];
+	u8 step_pos;
+	bool step_ov;
+};
+
+struct rtw89_btc_init_info {
+	struct rtw89_btc_module module;
+	u8 wl_guard_ch;
+
+	u8 wl_only: 1;
+	u8 wl_init_ok: 1;
+	u8 dbcc_en: 1;
+	u8 cx_other: 1;
+	u8 bt_only: 1;
+
+	u16 rsvd;
+};
+
+struct rtw89_btc_wl_tx_limit_para {
+	u16 enable;
+	u32 tx_time;	/* unit: us */
+	u16 tx_retry;
+};
+
+struct rtw89_btc_bt_scan_info {
+	u16 win;
+	u16 intvl;
+	u32 enable: 1;
+	u32 interlace: 1;
+	u32 rsvd: 30;
+};
+
+enum rtw89_btc_bt_scan_type {
+	BTC_SCAN_INQ	= 0,
+	BTC_SCAN_PAGE,
+	BTC_SCAN_BLE,
+	BTC_SCAN_INIT,
+	BTC_SCAN_TV,
+	BTC_SCAN_ADV,
+	BTC_SCAN_MAX1,
+};
+
+struct rtw89_btc_bt_info {
+	struct rtw89_btc_bt_link_info link_info;
+	struct rtw89_btc_bt_scan_info scan_info[BTC_SCAN_MAX1];
+	struct rtw89_btc_bt_ver_info ver_info;
+	struct rtw89_btc_bool_sta_chg enable;
+	struct rtw89_btc_bool_sta_chg inq_pag;
+	struct rtw89_btc_rf_para rf_para;
+	union rtw89_btc_bt_rfk_info_map rfk_info;
+
+	u8 raw_info[BTC_BTINFO_MAX]; /* raw bt info from mailbox */
+
+	u32 scbd;
+	u32 feature;
+
+	u32 mbx_avl: 1;
+	u32 whql_test: 1;
+	u32 igno_wl: 1;
+	u32 reinit: 1;
+	u32 ble_scan_en: 1;
+	u32 btg_type: 1;
+	u32 inq: 1;
+	u32 pag: 1;
+	u32 run_patch_code: 1;
+	u32 hi_lna_rx: 1;
+	u32 rsvd: 22;
+};
+
+struct rtw89_btc_cx {
+	struct rtw89_btc_wl_info wl;
+	struct rtw89_btc_bt_info bt;
+	struct rtw89_btc_3rdcx_info other;
+	u32 state_map;
+	u32 cnt_bt[BTC_BCNT_NUM];
+	u32 cnt_wl[BTC_WCNT_NUM];
+};
+
+struct rtw89_btc_fbtc_tdma {
+	u8 type;
+	u8 rxflctrl;
+	u8 txpause;
+	u8 wtgle_n;
+	u8 leak_n;
+	u8 ext_ctrl;
+	u8 rsvd0;
+	u8 rsvd1;
+} __packed;
+
+#define CXMREG_MAX 30
+#define FCXMAX_STEP 255 /*STEP trace record cnt, Max:65535, default:255*/
+#define BTCRPT_VER 1
+#define BTC_CYCLE_SLOT_MAX 48 /* must be even number, non-zero */
+
+enum rtw89_btc_bt_rfk_counter {
+	BTC_BCNT_RFK_REQ = 0,
+	BTC_BCNT_RFK_GO = 1,
+	BTC_BCNT_RFK_REJECT = 2,
+	BTC_BCNT_RFK_FAIL = 3,
+	BTC_BCNT_RFK_TIMEOUT = 4,
+	BTC_BCNT_RFK_MAX
+};
+
+struct rtw89_btc_fbtc_rpt_ctrl {
+	u16 fver;
+	u16 rpt_cnt; /* tmr counters */
+	u32 wl_fw_coex_ver; /* match which driver's coex version */
+	u32 wl_fw_cx_offload;
+	u32 wl_fw_ver;
+	u32 rpt_enable;
+	u32 rpt_para; /* ms */
+	u32 mb_send_fail_cnt; /* fw send mailbox fail counter */
+	u32 mb_send_ok_cnt; /* fw send mailbox ok counter */
+	u32 mb_recv_cnt; /* fw recv mailbox counter */
+	u32 mb_a2dp_empty_cnt; /* a2dp empty count */
+	u32 mb_a2dp_flct_cnt; /* a2dp empty flow control counter */
+	u32 mb_a2dp_full_cnt; /* a2dp empty full counter */
+	u32 bt_rfk_cnt[BTC_BCNT_RFK_MAX];
+	u32 c2h_cnt; /* fw send c2h counter  */
+	u32 h2c_cnt; /* fw recv h2c counter */
+} __packed;
+
+enum rtw89_fbtc_ext_ctrl_type {
+	CXECTL_OFF = 0x0, /* tdma off */
+	CXECTL_B2 = 0x1, /* allow B2 (beacon-early) */
+	CXECTL_EXT = 0x2,
+	CXECTL_MAX
+};
+
+union rtw89_btc_fbtc_rxflct {
+	u8 val;
+	u8 type: 3;
+	u8 tgln_n: 5;
+};
+
+enum rtw89_btc_cxst_state {
+	CXST_OFF = 0x0,
+	CXST_B2W = 0x1,
+	CXST_W1 = 0x2,
+	CXST_W2 = 0x3,
+	CXST_W2B = 0x4,
+	CXST_B1 = 0x5,
+	CXST_B2 = 0x6,
+	CXST_B3 = 0x7,
+	CXST_B4 = 0x8,
+	CXST_LK = 0x9,
+	CXST_BLK = 0xa,
+	CXST_E2G = 0xb,
+	CXST_E5G = 0xc,
+	CXST_EBT = 0xd,
+	CXST_ENULL = 0xe,
+	CXST_WLK = 0xf,
+	CXST_W1FDD = 0x10,
+	CXST_B1FDD = 0x11,
+	CXST_MAX = 0x12,
+};
+
+enum {
+	CXBCN_ALL = 0x0,
+	CXBCN_ALL_OK,
+	CXBCN_BT_SLOT,
+	CXBCN_BT_OK,
+	CXBCN_MAX
+};
+
+enum btc_slot_type {
+	SLOT_MIX = 0x0, /* accept BT Lower-Pri Tx/Rx request 0x778 = 1 */
+	SLOT_ISO = 0x1, /* no accept BT Lower-Pri Tx/Rx request 0x778 = d*/
+	CXSTYPE_NUM,
+};
+
+enum { /* TIME */
+	CXT_BT = 0x0,
+	CXT_WL = 0x1,
+	CXT_MAX
+};
+
+enum { /* TIME-A2DP */
+	CXT_FLCTRL_OFF = 0x0,
+	CXT_FLCTRL_ON = 0x1,
+	CXT_FLCTRL_MAX
+};
+
+enum { /* STEP TYPE */
+	CXSTEP_NONE = 0x0,
+	CXSTEP_EVNT = 0x1,
+	CXSTEP_SLOT = 0x2,
+	CXSTEP_MAX,
+};
+
+#define FCXGPIODBG_VER 1
+#define BTC_DBG_MAX1  32
+struct rtw89_btc_fbtc_gpio_dbg {
+	u8 fver;
+	u8 rsvd;
+	u16 rsvd2;
+	u32 en_map; /* which debug signal (see btc_wl_gpio_debug) is enable */
+	u32 pre_state; /* the debug signal is 1 or 0  */
+	u8 gpio_map[BTC_DBG_MAX1]; /*the debug signals to GPIO-Position */
+} __packed;
+
+#define FCXMREG_VER 1
+struct rtw89_btc_fbtc_mreg_val {
+	u8 fver;
+	u8 reg_num;
+	__le16 rsvd;
+	__le32 mreg_val[CXMREG_MAX];
+} __packed;
+
+#define RTW89_DEF_FBTC_MREG(__type, __bytes, __offset) \
+	{ .type = cpu_to_le16(__type), .bytes = cpu_to_le16(__bytes), \
+	  .offset = cpu_to_le32(__offset), }
+
+struct rtw89_btc_fbtc_mreg {
+	__le16 type;
+	__le16 bytes;
+	__le32 offset;
+} __packed;
+
+struct rtw89_btc_fbtc_slot {
+	__le16 dur;
+	__le32 cxtbl;
+	__le16 cxtype;
+} __packed;
+
+#define FCXSLOTS_VER 1
+struct rtw89_btc_fbtc_slots {
+	u8 fver;
+	u8 tbl_num;
+	__le16 rsvd;
+	__le32 update_map;
+	struct rtw89_btc_fbtc_slot slot[CXST_MAX];
+} __packed;
+
+#define FCXSTEP_VER 2
+struct rtw89_btc_fbtc_step {
+	u8 type;
+	u8 val;
+	__le16 difft;
+} __packed;
+
+struct rtw89_btc_fbtc_steps {
+	u8 fver;
+	u8 rsvd;
+	__le16 cnt;
+	__le16 pos_old;
+	__le16 pos_new;
+	struct rtw89_btc_fbtc_step step[FCXMAX_STEP];
+} __packed;
+
+#define FCXCYSTA_VER 2
+struct rtw89_btc_fbtc_cysta { /* statistics for cycles */
+	u8 fver;
+	u8 rsvd;
+	__le16 cycles; /* total cycle number */
+	__le16 cycles_a2dp[CXT_FLCTRL_MAX];
+	__le16 a2dpept; /* a2dp empty cnt */
+	__le16 a2dpeptto; /* a2dp empty timeout cnt*/
+	__le16 tavg_cycle[CXT_MAX]; /* avg wl/bt cycle time */
+	__le16 tmax_cycle[CXT_MAX]; /* max wl/bt cycle time */
+	__le16 tmaxdiff_cycle[CXT_MAX]; /* max wl-wl bt-bt cycle diff time */
+	__le16 tavg_a2dp[CXT_FLCTRL_MAX]; /* avg a2dp PSTDMA/TDMA time */
+	__le16 tmax_a2dp[CXT_FLCTRL_MAX]; /* max a2dp PSTDMA/TDMA time */
+	__le16 tavg_a2dpept; /* avg a2dp empty time */
+	__le16 tmax_a2dpept; /* max a2dp empty time */
+	__le16 tavg_lk; /* avg leak-slot time */
+	__le16 tmax_lk; /* max leak-slot time */
+	__le32 slot_cnt[CXST_MAX]; /* slot count */
+	__le32 bcn_cnt[CXBCN_MAX];
+	__le32 leakrx_cnt; /* the rximr occur at leak slot  */
+	__le32 collision_cnt; /* counter for event/timer occur at same time */
+	__le32 skip_cnt;
+	__le32 exception;
+	__le32 except_cnt;
+	__le16 tslot_cycle[BTC_CYCLE_SLOT_MAX];
+} __packed;
+
+#define FCXNULLSTA_VER 1
+struct rtw89_btc_fbtc_cynullsta { /* cycle null statistics */
+	u8 fver;
+	u8 rsvd;
+	__le16 rsvd2;
+	__le32 max_t[2]; /* max_t for 0:null0/1:null1 */
+	__le32 avg_t[2]; /* avg_t for 0:null0/1:null1 */
+	__le32 result[2][4]; /* 0:fail, 1:ok, 2:on_time, 3:retry */
+} __packed;
+
+#define FCX_BTVER_VER 1
+struct rtw89_btc_fbtc_btver {
+	u8 fver;
+	u8 rsvd;
+	__le16 rsvd2;
+	__le32 coex_ver; /*bit[15:8]->shared, bit[7:0]->non-shared */
+	__le32 fw_ver;
+	__le32 feature;
+} __packed;
+
+#define FCX_BTSCAN_VER 1
+struct rtw89_btc_fbtc_btscan {
+	u8 fver;
+	u8 rsvd;
+	__le16 rsvd2;
+	u8 scan[6];
+} __packed;
+
+#define FCX_BTAFH_VER 1
+struct rtw89_btc_fbtc_btafh {
+	u8 fver;
+	u8 rsvd;
+	__le16 rsvd2;
+	u8 afh_l[4]; /*bit0:2402, bit1: 2403.... bit31:2433 */
+	u8 afh_m[4]; /*bit0:2434, bit1: 2435.... bit31:2465 */
+	u8 afh_h[4]; /*bit0:2466, bit1:2467......bit14:2480 */
+} __packed;
+
+#define FCX_BTDEVINFO_VER 1
+struct rtw89_btc_fbtc_btdevinfo {
+	u8 fver;
+	u8 rsvd;
+	__le16 vendor_id;
+	__le32 dev_name; /* only 24 bits valid */
+	__le32 flush_time;
+} __packed;
+
+#define RTW89_BTC_WL_DEF_TX_PWR GENMASK(7, 0)
+struct rtw89_btc_rf_trx_para {
+	u32 wl_tx_power; /* absolute Tx power (dBm), 0xff-> no BTC control */
+	u32 wl_rx_gain;  /* rx gain table index (TBD.) */
+	u8 bt_tx_power; /* decrease Tx power (dB) */
+	u8 bt_rx_gain;  /* LNA constrain level */
+};
+
+struct rtw89_btc_dm {
+	struct rtw89_btc_fbtc_slot slot[CXST_MAX];
+	struct rtw89_btc_fbtc_slot slot_now[CXST_MAX];
+	struct rtw89_btc_fbtc_tdma tdma;
+	struct rtw89_btc_fbtc_tdma tdma_now;
+	struct rtw89_mac_ax_coex_gnt gnt;
+	struct rtw89_btc_init_info init_info; /* pass to wl_fw if offload */
+	struct rtw89_btc_rf_trx_para rf_trx_para;
+	struct rtw89_btc_wl_tx_limit_para wl_tx_limit;
+	struct rtw89_btc_dm_step dm_step;
+	union rtw89_btc_dm_error_map error;
+	u32 cnt_dm[BTC_DCNT_NUM];
+	u32 cnt_notify[BTC_NCNT_NUM];
+
+	u32 update_slot_map;
+	u32 set_ant_path;
+
+	u32 wl_only: 1;
+	u32 wl_fw_cx_offload: 1;
+	u32 freerun: 1;
+	u32 wl_ps_ctrl: 2;
+	u32 wl_mimo_ps: 1;
+	u32 leak_ap: 1;
+	u32 noisy_level: 3;
+	u32 coex_info_map: 8;
+	u32 bt_only: 1;
+	u32 wl_btg_rx: 1;
+	u32 trx_para_level: 8;
+	u32 wl_stb_chg: 1;
+	u32 rsvd: 3;
+
+	u16 slot_dur[CXST_MAX];
+
+	u8 run_reason;
+	u8 run_action;
+};
+
+struct rtw89_btc_ctrl {
+	u32 manual: 1;
+	u32 igno_bt: 1;
+	u32 always_freerun: 1;
+	u32 trace_step: 16;
+	u32 rsvd: 12;
+};
+
+struct rtw89_btc_dbg {
+	/* cmd "rb" */
+	bool rb_done;
+	u32 rb_val;
+};
+
+#define FCXTDMA_VER 1
+
+enum rtw89_btc_btf_fw_event {
+	BTF_EVNT_RPT = 0,
+	BTF_EVNT_BT_INFO = 1,
+	BTF_EVNT_BT_SCBD = 2,
+	BTF_EVNT_BT_REG = 3,
+	BTF_EVNT_CX_RUNINFO = 4,
+	BTF_EVNT_BT_PSD = 5,
+	BTF_EVNT_BUF_OVERFLOW,
+	BTF_EVNT_C2H_LOOPBACK,
+	BTF_EVNT_MAX,
+};
+
+enum btf_fw_event_report {
+	BTC_RPT_TYPE_CTRL = 0x0,
+	BTC_RPT_TYPE_TDMA,
+	BTC_RPT_TYPE_SLOT,
+	BTC_RPT_TYPE_CYSTA,
+	BTC_RPT_TYPE_STEP,
+	BTC_RPT_TYPE_NULLSTA,
+	BTC_RPT_TYPE_MREG,
+	BTC_RPT_TYPE_GPIO_DBG,
+	BTC_RPT_TYPE_BT_VER,
+	BTC_RPT_TYPE_BT_SCAN,
+	BTC_RPT_TYPE_BT_AFH,
+	BTC_RPT_TYPE_BT_DEVICE,
+	BTC_RPT_TYPE_TEST,
+	BTC_RPT_TYPE_MAX = 31
+};
+
+enum rtw_btc_btf_reg_type {
+	REG_MAC = 0x0,
+	REG_BB = 0x1,
+	REG_RF = 0x2,
+	REG_BT_RF = 0x3,
+	REG_BT_MODEM = 0x4,
+	REG_BT_BLUEWIZE = 0x5,
+	REG_BT_VENDOR = 0x6,
+	REG_BT_LE = 0x7,
+	REG_MAX_TYPE,
+};
+
+struct rtw89_btc_rpt_cmn_info {
+	u32 rx_cnt;
+	u32 rx_len;
+	u32 req_len; /* expected rsp len */
+	u8 req_fver; /* expected rsp fver */
+	u8 rsp_fver; /* fver from fw */
+	u8 valid;
+} __packed;
+
+struct rtw89_btc_report_ctrl_state {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_rpt_ctrl finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_tdma {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_tdma finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_slots {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_slots finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_cysta {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_cysta finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_step {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_steps finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_nullsta {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_cynullsta finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_mreg {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_mreg_val finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_gpio_dbg {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_gpio_dbg finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_btver {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_btver finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_btscan {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_btscan finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_btafh {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_btafh finfo; /* info from fw */
+};
+
+struct rtw89_btc_rpt_fbtc_btdev {
+	struct rtw89_btc_rpt_cmn_info cinfo; /* common info, by driver */
+	struct rtw89_btc_fbtc_btdevinfo finfo; /* info from fw */
+};
+
+enum rtw89_btc_btfre_type {
+	BTFRE_INVALID_INPUT = 0x0, /* invalid input parameters */
+	BTFRE_UNDEF_TYPE,
+	BTFRE_EXCEPTION,
+	BTFRE_MAX,
+};
+
+struct rtw89_btc_btf_fwinfo {
+	u32 cnt_c2h;
+	u32 cnt_h2c;
+	u32 cnt_h2c_fail;
+	u32 event[BTF_EVNT_MAX];
+
+	u32 err[BTFRE_MAX];
+	u32 len_mismch;
+	u32 fver_mismch;
+	u32 rpt_en_map;
+
+	struct rtw89_btc_report_ctrl_state rpt_ctrl;
+	struct rtw89_btc_rpt_fbtc_tdma rpt_fbtc_tdma;
+	struct rtw89_btc_rpt_fbtc_slots rpt_fbtc_slots;
+	struct rtw89_btc_rpt_fbtc_cysta rpt_fbtc_cysta;
+	struct rtw89_btc_rpt_fbtc_step rpt_fbtc_step;
+	struct rtw89_btc_rpt_fbtc_nullsta rpt_fbtc_nullsta;
+	struct rtw89_btc_rpt_fbtc_mreg rpt_fbtc_mregval;
+	struct rtw89_btc_rpt_fbtc_gpio_dbg rpt_fbtc_gpio_dbg;
+	struct rtw89_btc_rpt_fbtc_btver rpt_fbtc_btver;
+	struct rtw89_btc_rpt_fbtc_btscan rpt_fbtc_btscan;
+	struct rtw89_btc_rpt_fbtc_btafh rpt_fbtc_btafh;
+	struct rtw89_btc_rpt_fbtc_btdev rpt_fbtc_btdev;
+};
+
+#define RTW89_BTC_POLICY_MAXLEN 512
+
+struct rtw89_btc {
+	struct rtw89_btc_cx cx;
+	struct rtw89_btc_dm dm;
+	struct rtw89_btc_ctrl ctrl;
+	struct rtw89_btc_module mdinfo;
+	struct rtw89_btc_btf_fwinfo fwinfo;
+	struct rtw89_btc_dbg dbg;
+
+	struct work_struct eapol_notify_work;
+	struct work_struct arp_notify_work;
+	struct work_struct dhcp_notify_work;
+	struct work_struct icmp_notify_work;
+
+	u32 bt_req_len;
+
+	u8 policy[RTW89_BTC_POLICY_MAXLEN];
+	u16 policy_len;
+	u16 policy_type;
+	bool bt_req_en;
+	bool update_policy_force;
+	bool lps;
+};
+
+enum rtw89_ra_mode {
+	RTW89_RA_MODE_CCK = BIT(0),
+	RTW89_RA_MODE_OFDM = BIT(1),
+	RTW89_RA_MODE_HT = BIT(2),
+	RTW89_RA_MODE_VHT = BIT(3),
+	RTW89_RA_MODE_HE = BIT(4),
+};
+
+enum rtw89_ra_report_mode {
+	RTW89_RA_RPT_MODE_LEGACY,
+	RTW89_RA_RPT_MODE_HT,
+	RTW89_RA_RPT_MODE_VHT,
+	RTW89_RA_RPT_MODE_HE,
+};
+
+enum rtw89_dig_noisy_level {
+	RTW89_DIG_NOISY_LEVEL0 = -1,
+	RTW89_DIG_NOISY_LEVEL1 = 0,
+	RTW89_DIG_NOISY_LEVEL2 = 1,
+	RTW89_DIG_NOISY_LEVEL3 = 2,
+	RTW89_DIG_NOISY_LEVEL_MAX = 3,
+};
+
+enum rtw89_gi_ltf {
+	RTW89_GILTF_LGI_4XHE32 = 0,
+	RTW89_GILTF_SGI_4XHE08 = 1,
+	RTW89_GILTF_2XHE16 = 2,
+	RTW89_GILTF_2XHE08 = 3,
+	RTW89_GILTF_1XHE16 = 4,
+	RTW89_GILTF_1XHE08 = 5,
+	RTW89_GILTF_MAX
+};
+
+enum rtw89_rx_frame_type {
+	RTW89_RX_TYPE_MGNT = 0,
+	RTW89_RX_TYPE_CTRL = 1,
+	RTW89_RX_TYPE_DATA = 2,
+	RTW89_RX_TYPE_RSVD = 3,
+};
+
+struct rtw89_ra_info {
+	u8 is_dis_ra:1;
+	/* Bit0 : CCK
+	 * Bit1 : OFDM
+	 * Bit2 : HT
+	 * Bit3 : VHT
+	 * Bit4 : HE
+	 */
+	u8 mode_ctrl:5;
+	u8 bw_cap:2;
+	u8 macid;
+	u8 dcm_cap:1;
+	u8 er_cap:1;
+	u8 init_rate_lv:2;
+	u8 upd_all:1;
+	u8 en_sgi:1;
+	u8 ldpc_cap:1;
+	u8 stbc_cap:1;
+	u8 ss_num:3;
+	u8 giltf:3;
+	u8 upd_bw_nss_mask:1;
+	u8 upd_mask:1;
+	u64 ra_mask; /* 63 bits ra_mask + 1 bit CSI ctrl */
+	/* BFee CSI */
+	u8 band_num;
+	u8 ra_csi_rate_en:1;
+	u8 fixed_csi_rate_en:1;
+	u8 cr_tbl_sel:1;
+	u8 rsvd2:5;
+	u8 csi_mcs_ss_idx;
+	u8 csi_mode:2;
+	u8 csi_gi_ltf:3;
+	u8 csi_bw:3;
+};
+
+#define RTW89_PPDU_MAX_USR 4
+#define RTW89_PPDU_MAC_INFO_USR_SIZE 4
+#define RTW89_PPDU_MAC_INFO_SIZE 8
+#define RTW89_PPDU_MAC_RX_CNT_SIZE 96
+
+#define RTW89_MAX_RX_AGG_NUM 64
+#define RTW89_MAX_TX_AGG_NUM 128
+
+struct rtw89_ampdu_params {
+	u16 agg_num;
+	bool amsdu;
+};
+
+struct rtw89_ra_report {
+	struct rate_info txrate;
+	u32 bit_rate;
+	u16 hw_rate;
+};
+
+DECLARE_EWMA(rssi, 10, 16);
+
+struct rtw89_sta {
+	u8 mac_id;
+	bool disassoc;
+	struct rtw89_vif *rtwvif;
+	struct rtw89_ra_info ra;
+	struct rtw89_ra_report ra_report;
+	int max_agg_wait;
+	u8 prev_rssi;
+	struct ewma_rssi avg_rssi;
+	struct rtw89_ampdu_params ampdu_params[IEEE80211_NUM_TIDS];
+	struct ieee80211_rx_status rx_status;
+	u16 rx_hw_rate;
+	__le32 htc_template;
+
+	bool use_cfg_mask;
+	struct cfg80211_bitrate_mask mask;
+
+	bool cctl_tx_time;
+	u32 ampdu_max_time:4;
+	bool cctl_tx_retry_limit;
+	u32 data_tx_cnt_lmt:6;
+};
+
+#define RTW89_MAX_ADDR_CAM_NUM		128
+#define RTW89_MAX_BSSID_CAM_NUM		20
+#define RTW89_MAX_SEC_CAM_NUM		128
+#define RTW89_SEC_CAM_IN_ADDR_CAM	7
+
+struct rtw89_addr_cam_entry {
+	u8 addr_cam_idx;
+	u8 offset;
+	u8 len;
+	u8 valid	: 1;
+	u8 addr_mask	: 6;
+	u8 wapi		: 1;
+	u8 mask_sel	: 2;
+	u8 bssid_cam_idx: 6;
+	u8 tma[ETH_ALEN];
+	u8 sma[ETH_ALEN];
+
+	u8 sec_ent_mode;
+	DECLARE_BITMAP(sec_cam_map, RTW89_SEC_CAM_IN_ADDR_CAM);
+	u8 sec_ent_keyid[RTW89_SEC_CAM_IN_ADDR_CAM];
+	u8 sec_ent[RTW89_SEC_CAM_IN_ADDR_CAM];
+	struct rtw89_sec_cam_entry *sec_entries[RTW89_SEC_CAM_IN_ADDR_CAM];
+};
+
+struct rtw89_bssid_cam_entry {
+	u8 bssid[ETH_ALEN];
+	u8 phy_idx;
+	u8 bssid_cam_idx;
+	u8 offset;
+	u8 len;
+	u8 valid : 1;
+	u8 num;
+};
+
+struct rtw89_sec_cam_entry {
+	u8 sec_cam_idx;
+	u8 offset;
+	u8 len;
+	u8 type : 4;
+	u8 ext_key : 1;
+	u8 spp_mode : 1;
+	/* 256 bits */
+	u8 key[32];
+};
+
+struct rtw89_efuse {
+	bool valid;
+	u8 xtal_cap;
+	u8 addr[ETH_ALEN];
+	u8 rfe_type;
+	char country_code[2];
+};
+
+struct rtw89_phy_rate_pattern {
+	u64 ra_mask;
+	u16 rate;
+	u8 ra_mode;
+	bool enable;
+};
+
+struct rtw89_vif {
+	struct list_head list;
+	u8 mac_id;
+	u8 port;
+	u8 mac_addr[ETH_ALEN];
+	u8 bssid[ETH_ALEN];
+	u8 phy_idx;
+	u8 mac_idx;
+	u8 net_type;
+	u8 wifi_role;
+	u8 self_role;
+	u8 wmm;
+	u8 bcn_hit_cond;
+	u8 hit_rule;
+	bool trigger;
+	bool lsig_txop;
+	u8 tgt_ind;
+	u8 frm_tgt_ind;
+	bool wowlan_pattern;
+	bool wowlan_uc;
+	bool wowlan_magic;
+	bool is_hesta;
+	bool last_a_ctrl;
+	union {
+		struct {
+			struct ieee80211_sta *ap;
+		} mgd;
+		struct {
+			struct list_head sta_list;
+		} ap;
+	};
+	struct rtw89_addr_cam_entry addr_cam;
+	struct rtw89_bssid_cam_entry bssid_cam;
+	struct ieee80211_tx_queue_params tx_params[IEEE80211_NUM_ACS];
+	struct rtw89_traffic_stats stats;
+	struct rtw89_phy_rate_pattern rate_pattern;
+};
+
+enum rtw89_lv1_rcvy_step {
+	RTW89_LV1_RCVY_STEP_1,
+	RTW89_LV1_RCVY_STEP_2,
+};
+
+struct rtw89_hci_ops {
+	int (*tx_write)(struct rtw89_dev *rtwdev, struct rtw89_core_tx_request *tx_req);
+	void (*tx_kick_off)(struct rtw89_dev *rtwdev, u8 txch);
+	void (*flush_queues)(struct rtw89_dev *rtwdev, u32 queues, bool drop);
+	void (*reset)(struct rtw89_dev *rtwdev);
+	int (*start)(struct rtw89_dev *rtwdev);
+	void (*stop)(struct rtw89_dev *rtwdev);
+	void (*recalc_int_mit)(struct rtw89_dev *rtwdev);
+
+	u8 (*read8)(struct rtw89_dev *rtwdev, u32 addr);
+	u16 (*read16)(struct rtw89_dev *rtwdev, u32 addr);
+	u32 (*read32)(struct rtw89_dev *rtwdev, u32 addr);
+	void (*write8)(struct rtw89_dev *rtwdev, u32 addr, u8 data);
+	void (*write16)(struct rtw89_dev *rtwdev, u32 addr, u16 data);
+	void (*write32)(struct rtw89_dev *rtwdev, u32 addr, u32 data);
+
+	int (*mac_pre_init)(struct rtw89_dev *rtwdev);
+	int (*mac_post_init)(struct rtw89_dev *rtwdev);
+	int (*deinit)(struct rtw89_dev *rtwdev);
+
+	u32 (*check_and_reclaim_tx_resource)(struct rtw89_dev *rtwdev, u8 txch);
+	int (*mac_lv1_rcvy)(struct rtw89_dev *rtwdev, enum rtw89_lv1_rcvy_step step);
+	void (*dump_err_status)(struct rtw89_dev *rtwdev);
+	int (*napi_poll)(struct napi_struct *napi, int budget);
+};
+
+struct rtw89_hci_info {
+	const struct rtw89_hci_ops *ops;
+	enum rtw89_hci_type type;
+	u32 rpwm_addr;
+	u32 cpwm_addr;
+};
+
+struct rtw89_chip_ops {
+	void (*bb_reset)(struct rtw89_dev *rtwdev,
+			 enum rtw89_phy_idx phy_idx);
+	void (*bb_sethw)(struct rtw89_dev *rtwdev);
+	u32 (*read_rf)(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+		       u32 addr, u32 mask);
+	bool (*write_rf)(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+			 u32 addr, u32 mask, u32 data);
+	void (*set_channel)(struct rtw89_dev *rtwdev,
+			    struct rtw89_channel_params *param);
+	void (*set_channel_help)(struct rtw89_dev *rtwdev, bool enter,
+				 struct rtw89_channel_help_params *p);
+	int (*read_efuse)(struct rtw89_dev *rtwdev, u8 *log_map);
+	int (*read_phycap)(struct rtw89_dev *rtwdev, u8 *phycap_map);
+	void (*fem_setup)(struct rtw89_dev *rtwdev);
+	void (*rfk_init)(struct rtw89_dev *rtwdev);
+	void (*rfk_channel)(struct rtw89_dev *rtwdev);
+	void (*rfk_band_changed)(struct rtw89_dev *rtwdev);
+	void (*rfk_scan)(struct rtw89_dev *rtwdev, bool start);
+	void (*rfk_track)(struct rtw89_dev *rtwdev);
+	void (*power_trim)(struct rtw89_dev *rtwdev);
+	void (*set_txpwr)(struct rtw89_dev *rtwdev);
+	void (*set_txpwr_ctrl)(struct rtw89_dev *rtwdev);
+	int (*init_txpwr_unit)(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx);
+	u8 (*get_thermal)(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path);
+	void (*ctrl_btg)(struct rtw89_dev *rtwdev, bool btg);
+	void (*query_ppdu)(struct rtw89_dev *rtwdev,
+			   struct rtw89_rx_phy_ppdu *phy_ppdu,
+			   struct ieee80211_rx_status *status);
+	void (*bb_ctrl_btc_preagc)(struct rtw89_dev *rtwdev, bool bt_en);
+	void (*set_txpwr_ul_tb_offset)(struct rtw89_dev *rtwdev,
+				       s16 pw_ofst, enum rtw89_mac_idx mac_idx);
+
+	void (*btc_set_rfe)(struct rtw89_dev *rtwdev);
+	void (*btc_init_cfg)(struct rtw89_dev *rtwdev);
+	void (*btc_set_wl_pri)(struct rtw89_dev *rtwdev, u8 map, bool state);
+	void (*btc_set_wl_txpwr_ctrl)(struct rtw89_dev *rtwdev, u32 txpwr_val);
+	s8 (*btc_get_bt_rssi)(struct rtw89_dev *rtwdev, s8 val);
+	void (*btc_bt_aci_imp)(struct rtw89_dev *rtwdev);
+	void (*btc_update_bt_cnt)(struct rtw89_dev *rtwdev);
+	void (*btc_wl_s1_standby)(struct rtw89_dev *rtwdev, bool state);
+};
+
+enum rtw89_dma_ch {
+	RTW89_DMA_ACH0 = 0,
+	RTW89_DMA_ACH1 = 1,
+	RTW89_DMA_ACH2 = 2,
+	RTW89_DMA_ACH3 = 3,
+	RTW89_DMA_ACH4 = 4,
+	RTW89_DMA_ACH5 = 5,
+	RTW89_DMA_ACH6 = 6,
+	RTW89_DMA_ACH7 = 7,
+	RTW89_DMA_B0MG = 8,
+	RTW89_DMA_B0HI = 9,
+	RTW89_DMA_B1MG = 10,
+	RTW89_DMA_B1HI = 11,
+	RTW89_DMA_H2C = 12,
+	RTW89_DMA_CH_NUM = 13
+};
+
+enum rtw89_qta_mode {
+	RTW89_QTA_SCC,
+	RTW89_QTA_DLFW,
+
+	/* keep last */
+	RTW89_QTA_INVALID,
+};
+
+struct rtw89_hfc_ch_cfg {
+	u16 min;
+	u16 max;
+#define grp_0 0
+#define grp_1 1
+#define grp_num 2
+	u8 grp;
+};
+
+struct rtw89_hfc_ch_info {
+	u16 aval;
+	u16 used;
+};
+
+struct rtw89_hfc_pub_cfg {
+	u16 grp0;
+	u16 grp1;
+	u16 pub_max;
+	u16 wp_thrd;
+};
+
+struct rtw89_hfc_pub_info {
+	u16 g0_used;
+	u16 g1_used;
+	u16 g0_aval;
+	u16 g1_aval;
+	u16 pub_aval;
+	u16 wp_aval;
+};
+
+struct rtw89_hfc_prec_cfg {
+	u16 ch011_prec;
+	u16 h2c_prec;
+	u16 wp_ch07_prec;
+	u16 wp_ch811_prec;
+	u8 ch011_full_cond;
+	u8 h2c_full_cond;
+	u8 wp_ch07_full_cond;
+	u8 wp_ch811_full_cond;
+};
+
+struct rtw89_hfc_param {
+	bool en;
+	bool h2c_en;
+	u8 mode;
+	const struct rtw89_hfc_ch_cfg *ch_cfg;
+	struct rtw89_hfc_ch_info ch_info[RTW89_DMA_CH_NUM];
+	struct rtw89_hfc_pub_cfg pub_cfg;
+	struct rtw89_hfc_pub_info pub_info;
+	struct rtw89_hfc_prec_cfg prec_cfg;
+};
+
+struct rtw89_hfc_param_ini {
+	const struct rtw89_hfc_ch_cfg *ch_cfg;
+	const struct rtw89_hfc_pub_cfg *pub_cfg;
+	const struct rtw89_hfc_prec_cfg *prec_cfg;
+	u8 mode;
+};
+
+struct rtw89_dle_size {
+	u16 pge_size;
+	u16 lnk_pge_num;
+	u16 unlnk_pge_num;
+};
+
+struct rtw89_wde_quota {
+	u16 hif;
+	u16 wcpu;
+	u16 pkt_in;
+	u16 cpu_io;
+};
+
+struct rtw89_ple_quota {
+	u16 cma0_tx;
+	u16 cma1_tx;
+	u16 c2h;
+	u16 h2c;
+	u16 wcpu;
+	u16 mpdu_proc;
+	u16 cma0_dma;
+	u16 cma1_dma;
+	u16 bb_rpt;
+	u16 wd_rel;
+	u16 cpu_io;
+};
+
+struct rtw89_dle_mem {
+	enum rtw89_qta_mode mode;
+	const struct rtw89_dle_size *wde_size;
+	const struct rtw89_dle_size *ple_size;
+	const struct rtw89_wde_quota *wde_min_qt;
+	const struct rtw89_wde_quota *wde_max_qt;
+	const struct rtw89_ple_quota *ple_min_qt;
+	const struct rtw89_ple_quota *ple_max_qt;
+};
+
+struct rtw89_reg_def {
+	u32 addr;
+	u32 mask;
+};
+
+struct rtw89_reg2_def {
+	u32 addr;
+	u32 data;
+};
+
+struct rtw89_reg3_def {
+	u32 addr;
+	u32 mask;
+	u32 data;
+};
+
+struct rtw89_reg5_def {
+	u8 flag; /* recognized by parsers */
+	u8 path;
+	u32 addr;
+	u32 mask;
+	u32 data;
+};
+
+struct rtw89_phy_table {
+	const struct rtw89_reg2_def *regs;
+	u32 n_regs;
+	enum rtw89_rf_path rf_path;
+};
+
+struct rtw89_txpwr_table {
+	const void *data;
+	u32 size;
+	void (*load)(struct rtw89_dev *rtwdev,
+		     const struct rtw89_txpwr_table *tbl);
+};
+
+struct rtw89_chip_info {
+	enum rtw89_core_chip_id chip_id;
+	const struct rtw89_chip_ops *ops;
+	const char *fw_name;
+	u32 fifo_size;
+	u16 max_amsdu_limit;
+	bool dis_2g_40m_ul_ofdma;
+	const struct rtw89_hfc_param_ini *hfc_param_ini;
+	const struct rtw89_dle_mem *dle_mem;
+	u32 rf_base_addr[2];
+	u8 rf_path_num;
+	u8 tx_nss;
+	u8 rx_nss;
+	u8 acam_num;
+	u8 bcam_num;
+	u8 scam_num;
+
+	u8 sec_ctrl_efuse_size;
+	u32 physical_efuse_size;
+	u32 logical_efuse_size;
+	u32 limit_efuse_size;
+	u32 phycap_addr;
+	u32 phycap_size;
+
+	const struct rtw89_pwr_cfg * const *pwr_on_seq;
+	const struct rtw89_pwr_cfg * const *pwr_off_seq;
+	const struct rtw89_phy_table *bb_table;
+	const struct rtw89_phy_table *rf_table[RF_PATH_MAX];
+	const struct rtw89_phy_table *nctl_table;
+	const struct rtw89_txpwr_table *byr_table;
+	const struct rtw89_phy_dig_gain_table *dig_table;
+	const s8 (*txpwr_lmt_2g)[RTW89_2G_BW_NUM][RTW89_NTX_NUM]
+				[RTW89_RS_LMT_NUM][RTW89_BF_NUM]
+				[RTW89_REGD_NUM][RTW89_2G_CH_NUM];
+	const s8 (*txpwr_lmt_5g)[RTW89_5G_BW_NUM][RTW89_NTX_NUM]
+				[RTW89_RS_LMT_NUM][RTW89_BF_NUM]
+				[RTW89_REGD_NUM][RTW89_5G_CH_NUM];
+	const s8 (*txpwr_lmt_ru_2g)[RTW89_RU_NUM][RTW89_NTX_NUM]
+				   [RTW89_REGD_NUM][RTW89_2G_CH_NUM];
+	const s8 (*txpwr_lmt_ru_5g)[RTW89_RU_NUM][RTW89_NTX_NUM]
+				   [RTW89_REGD_NUM][RTW89_5G_CH_NUM];
+
+	u8 txpwr_factor_rf;
+	u8 txpwr_factor_mac;
+
+	u32 para_ver;
+	u32 wlcx_desired;
+	u8 btcx_desired;
+	u8 scbd;
+	u8 mailbox;
+
+	u8 afh_guard_ch;
+	const u8 *wl_rssi_thres;
+	const u8 *bt_rssi_thres;
+	u8 rssi_tol;
+
+	u8 mon_reg_num;
+	const struct rtw89_btc_fbtc_mreg *mon_reg;
+	u8 rf_para_ulink_num;
+	const struct rtw89_btc_rf_trx_para *rf_para_ulink;
+	u8 rf_para_dlink_num;
+	const struct rtw89_btc_rf_trx_para *rf_para_dlink;
+	u8 ps_mode_supported;
+};
+
+enum rtw89_hcifc_mode {
+	RTW89_HCIFC_POH = 0,
+	RTW89_HCIFC_STF = 1,
+	RTW89_HCIFC_SDIO = 2,
+
+	/* keep last */
+	RTW89_HCIFC_MODE_INVALID,
+};
+
+struct rtw89_dle_info {
+	enum rtw89_qta_mode qta_mode;
+	u16 wde_pg_size;
+	u16 ple_pg_size;
+	u16 c0_rx_qta;
+	u16 c1_rx_qta;
+};
+
+enum rtw89_host_rpr_mode {
+	RTW89_RPR_MODE_POH = 0,
+	RTW89_RPR_MODE_STF
+};
+
+struct rtw89_mac_info {
+	struct rtw89_dle_info dle_info;
+	struct rtw89_hfc_param hfc_param;
+	enum rtw89_qta_mode qta_mode;
+	u8 rpwm_seq_num;
+	u8 cpwm_seq_num;
+};
+
+enum rtw89_fw_type {
+	RTW89_FW_NORMAL = 1,
+	RTW89_FW_WOWLAN = 3,
+};
+
+struct rtw89_fw_suit {
+	const u8 *data;
+	u32 size;
+	u8 major_ver;
+	u8 minor_ver;
+	u8 sub_ver;
+	u8 sub_idex;
+	u16 build_year;
+	u16 build_mon;
+	u16 build_date;
+	u16 build_hour;
+	u16 build_min;
+	u8 cmd_ver;
+};
+
+#define RTW89_FW_VER_CODE(major, minor, sub, idx)	\
+	(((major) << 24) | ((minor) << 16) | ((sub) << 8) | (idx))
+#define RTW89_FW_SUIT_VER_CODE(s)	\
+	RTW89_FW_VER_CODE((s)->major_ver, (s)->minor_ver, (s)->sub_ver, (s)->sub_idex)
+
+struct rtw89_fw_info {
+	const struct firmware *firmware;
+	struct rtw89_dev *rtwdev;
+	struct completion completion;
+	u8 h2c_seq;
+	u8 rec_seq;
+	struct rtw89_fw_suit normal;
+	struct rtw89_fw_suit wowlan;
+	bool fw_log_enable;
+	bool old_ht_ra_format;
+};
+
+struct rtw89_cam_info {
+	DECLARE_BITMAP(addr_cam_map, RTW89_MAX_ADDR_CAM_NUM);
+	DECLARE_BITMAP(bssid_cam_map, RTW89_MAX_BSSID_CAM_NUM);
+	DECLARE_BITMAP(sec_cam_map, RTW89_MAX_SEC_CAM_NUM);
+};
+
+enum rtw89_sar_sources {
+	RTW89_SAR_SOURCE_NONE,
+	RTW89_SAR_SOURCE_COMMON,
+
+	RTW89_SAR_SOURCE_NR,
+};
+
+struct rtw89_sar_cfg_common {
+	bool set[RTW89_SUBBAND_NR];
+	s32 cfg[RTW89_SUBBAND_NR];
+};
+
+struct rtw89_sar_info {
+	/* used to decide how to acces SAR cfg union */
+	enum rtw89_sar_sources src;
+
+	/* reserved for different knids of SAR cfg struct.
+	 * supposed that a single cfg struct cannot handle various SAR sources.
+	 */
+	union {
+		struct rtw89_sar_cfg_common cfg_common;
+	};
+};
+
+struct rtw89_hal {
+	u32 rx_fltr;
+	u8 cv;
+	u8 current_channel;
+	u8 current_primary_channel;
+	enum rtw89_subband current_subband;
+	u8 current_band_width;
+	u8 current_band_type;
+	/* center channel for different available bandwidth,
+	 * val of (bw > current_band_width) is invalid
+	 */
+	u8 cch_by_bw[RTW89_MAX_CHANNEL_WIDTH + 1];
+	u32 sw_amsdu_max_size;
+	u32 antenna_tx;
+	u32 antenna_rx;
+	u8 tx_nss;
+	u8 rx_nss;
+};
+
+#define RTW89_MAX_MAC_ID_NUM 128
+
+enum rtw89_flags {
+	RTW89_FLAG_POWERON,
+	RTW89_FLAG_FW_RDY,
+	RTW89_FLAG_RUNNING,
+	RTW89_FLAG_BFEE_MON,
+	RTW89_FLAG_BFEE_EN,
+	RTW89_FLAG_NAPI_RUNNING,
+	RTW89_FLAG_LEISURE_PS,
+	RTW89_FLAG_LOW_POWER_MODE,
+	RTW89_FLAG_INACTIVE_PS,
+
+	NUM_OF_RTW89_FLAGS,
+};
+
+struct rtw89_pkt_stat {
+	u16 beacon_nr;
+	u32 rx_rate_cnt[RTW89_HW_RATE_NR];
+};
+
+DECLARE_EWMA(thermal, 4, 4);
+
+struct rtw89_phy_stat {
+	struct ewma_thermal avg_thermal[RF_PATH_MAX];
+	struct rtw89_pkt_stat cur_pkt_stat;
+	struct rtw89_pkt_stat last_pkt_stat;
+};
+
+#define RTW89_DACK_PATH_NR 2
+#define RTW89_DACK_IDX_NR 2
+#define RTW89_DACK_MSBK_NR 16
+struct rtw89_dack_info {
+	bool dack_done;
+	u8 msbk_d[RTW89_DACK_PATH_NR][RTW89_DACK_IDX_NR][RTW89_DACK_MSBK_NR];
+	u8 dadck_d[RTW89_DACK_PATH_NR][RTW89_DACK_IDX_NR];
+	u16 addck_d[RTW89_DACK_PATH_NR][RTW89_DACK_IDX_NR];
+	u16 biask_d[RTW89_DACK_PATH_NR][RTW89_DACK_IDX_NR];
+	u32 dack_cnt;
+	bool addck_timeout[RTW89_DACK_PATH_NR];
+	bool dadck_timeout[RTW89_DACK_PATH_NR];
+	bool msbk_timeout[RTW89_DACK_PATH_NR];
+};
+
+#define RTW89_IQK_CHS_NR 2
+#define RTW89_IQK_PATH_NR 4
+struct rtw89_iqk_info {
+	bool lok_cor_fail[RTW89_IQK_CHS_NR][RTW89_IQK_PATH_NR];
+	bool lok_fin_fail[RTW89_IQK_CHS_NR][RTW89_IQK_PATH_NR];
+	bool iqk_tx_fail[RTW89_IQK_CHS_NR][RTW89_IQK_PATH_NR];
+	bool iqk_rx_fail[RTW89_IQK_CHS_NR][RTW89_IQK_PATH_NR];
+	u32 iqk_fail_cnt;
+	bool is_iqk_init;
+	u32 iqk_channel[RTW89_IQK_CHS_NR];
+	u8 iqk_band[RTW89_IQK_PATH_NR];
+	u8 iqk_ch[RTW89_IQK_PATH_NR];
+	u8 iqk_bw[RTW89_IQK_PATH_NR];
+	u8 kcount;
+	u8 iqk_times;
+	u8 version;
+	u32 nb_txcfir[RTW89_IQK_PATH_NR];
+	u32 nb_rxcfir[RTW89_IQK_PATH_NR];
+	u32 bp_txkresult[RTW89_IQK_PATH_NR];
+	u32 bp_rxkresult[RTW89_IQK_PATH_NR];
+	u32 bp_iqkenable[RTW89_IQK_PATH_NR];
+	bool is_wb_txiqk[RTW89_IQK_PATH_NR];
+	bool is_wb_rxiqk[RTW89_IQK_PATH_NR];
+	bool is_nbiqk;
+	bool iqk_fft_en;
+	bool iqk_xym_en;
+	bool iqk_sram_en;
+	bool iqk_cfir_en;
+	u8 thermal[RTW89_IQK_PATH_NR];
+	bool thermal_rek_en;
+	u32 syn1to2;
+	u8 iqk_mcc_ch[RTW89_IQK_CHS_NR][RTW89_IQK_PATH_NR];
+	u8 iqk_table_idx[RTW89_IQK_PATH_NR];
+};
+
+#define RTW89_DPK_RF_PATH 2
+#define RTW89_DPK_AVG_THERMAL_NUM 8
+#define RTW89_DPK_BKUP_NUM 2
+struct rtw89_dpk_bkup_para {
+	enum rtw89_band band;
+	enum rtw89_bandwidth bw;
+	u8 ch;
+	bool path_ok;
+	u8 txagc_dpk;
+	u8 ther_dpk;
+	u8 gs;
+	u16 pwsf;
+};
+
+struct rtw89_dpk_info {
+	bool is_dpk_enable;
+	bool is_dpk_reload_en;
+	u16 dc_i[RTW89_DPK_RF_PATH];
+	u16 dc_q[RTW89_DPK_RF_PATH];
+	u8 corr_val[RTW89_DPK_RF_PATH];
+	u8 corr_idx[RTW89_DPK_RF_PATH];
+	u8 cur_idx[RTW89_DPK_RF_PATH];
+	struct rtw89_dpk_bkup_para bp[RTW89_DPK_RF_PATH][RTW89_DPK_BKUP_NUM];
+};
+
+struct rtw89_fem_info {
+	bool elna_2g;
+	bool elna_5g;
+	bool epa_2g;
+	bool epa_5g;
+};
+
+struct rtw89_phy_ch_info {
+	u8 rssi_min;
+	u16 rssi_min_macid;
+	u8 pre_rssi_min;
+	u8 rssi_max;
+	u16 rssi_max_macid;
+	u8 rxsc_160;
+	u8 rxsc_80;
+	u8 rxsc_40;
+	u8 rxsc_20;
+	u8 rxsc_l;
+	u8 is_noisy;
+};
+
+struct rtw89_agc_gaincode_set {
+	u8 lna_idx;
+	u8 tia_idx;
+	u8 rxb_idx;
+};
+
+#define IGI_RSSI_TH_NUM 5
+#define FA_TH_NUM 4
+#define LNA_GAIN_NUM 7
+#define TIA_GAIN_NUM 2
+struct rtw89_dig_info {
+	struct rtw89_agc_gaincode_set cur_gaincode;
+	bool force_gaincode_idx_en;
+	struct rtw89_agc_gaincode_set force_gaincode;
+	u8 igi_rssi_th[IGI_RSSI_TH_NUM];
+	u16 fa_th[FA_TH_NUM];
+	u8 igi_rssi;
+	u8 igi_fa_rssi;
+	u8 fa_rssi_ofst;
+	u8 dyn_igi_max;
+	u8 dyn_igi_min;
+	bool dyn_pd_th_en;
+	u8 dyn_pd_th_max;
+	u8 pd_low_th_ofst;
+	u8 ib_pbk;
+	s8 ib_pkpwr;
+	s8 lna_gain_a[LNA_GAIN_NUM];
+	s8 lna_gain_g[LNA_GAIN_NUM];
+	s8 *lna_gain;
+	s8 tia_gain_a[TIA_GAIN_NUM];
+	s8 tia_gain_g[TIA_GAIN_NUM];
+	s8 *tia_gain;
+	bool is_linked_pre;
+	bool bypass_dig;
+};
+
+enum rtw89_multi_cfo_mode {
+	RTW89_PKT_BASED_AVG_MODE = 0,
+	RTW89_ENTRY_BASED_AVG_MODE = 1,
+	RTW89_TP_BASED_AVG_MODE = 2,
+};
+
+enum rtw89_phy_cfo_status {
+	RTW89_PHY_DCFO_STATE_NORMAL = 0,
+	RTW89_PHY_DCFO_STATE_ENHANCE = 1,
+	RTW89_PHY_DCFO_STATE_MAX
+};
+
+struct rtw89_cfo_tracking_info {
+	u16 cfo_timer_ms;
+	bool cfo_trig_by_timer_en;
+	enum rtw89_phy_cfo_status phy_cfo_status;
+	u8 phy_cfo_trk_cnt;
+	bool is_adjust;
+	enum rtw89_multi_cfo_mode rtw89_multi_cfo_mode;
+	bool apply_compensation;
+	u8 crystal_cap;
+	u8 crystal_cap_default;
+	u8 def_x_cap;
+	s8 x_cap_ofst;
+	u32 sta_cfo_tolerance;
+	s32 cfo_tail[CFO_TRACK_MAX_USER];
+	u16 cfo_cnt[CFO_TRACK_MAX_USER];
+	s32 cfo_avg_pre;
+	s32 cfo_avg[CFO_TRACK_MAX_USER];
+	s32 pre_cfo_avg[CFO_TRACK_MAX_USER];
+	u32 packet_count;
+	u32 packet_count_pre;
+	s32 residual_cfo_acc;
+	u8 phy_cfotrk_state;
+	u8 phy_cfotrk_cnt;
+};
+
+/* 2GL, 2GH, 5GL1, 5GH1, 5GM1, 5GM2, 5GH1, 5GH2 */
+#define TSSI_TRIM_CH_GROUP_NUM 8
+
+#define TSSI_CCK_CH_GROUP_NUM 6
+#define TSSI_MCS_2G_CH_GROUP_NUM 5
+#define TSSI_MCS_5G_CH_GROUP_NUM 14
+#define TSSI_MCS_CH_GROUP_NUM \
+	(TSSI_MCS_2G_CH_GROUP_NUM + TSSI_MCS_5G_CH_GROUP_NUM)
+
+struct rtw89_tssi_info {
+	u8 thermal[RF_PATH_MAX];
+	s8 tssi_trim[RF_PATH_MAX][TSSI_TRIM_CH_GROUP_NUM];
+	s8 tssi_cck[RF_PATH_MAX][TSSI_CCK_CH_GROUP_NUM];
+	s8 tssi_mcs[RF_PATH_MAX][TSSI_MCS_CH_GROUP_NUM];
+	s8 extra_ofst[RF_PATH_MAX];
+	bool tssi_tracking_check[RF_PATH_MAX];
+	u8 default_txagc_offset[RF_PATH_MAX];
+	u32 base_thermal[RF_PATH_MAX];
+};
+
+struct rtw89_power_trim_info {
+	bool pg_thermal_trim;
+	bool pg_pa_bias_trim;
+	u8 thermal_trim[RF_PATH_MAX];
+	u8 pa_bias_trim[RF_PATH_MAX];
+};
+
+struct rtw89_regulatory {
+	char alpha2[3];
+	u8 txpwr_regd[RTW89_BAND_MAX];
+};
+
+enum rtw89_ifs_clm_application {
+	RTW89_IFS_CLM_INIT = 0,
+	RTW89_IFS_CLM_BACKGROUND = 1,
+	RTW89_IFS_CLM_ACS = 2,
+	RTW89_IFS_CLM_DIG = 3,
+	RTW89_IFS_CLM_TDMA_DIG = 4,
+	RTW89_IFS_CLM_DBG = 5,
+	RTW89_IFS_CLM_DBG_MANUAL = 6
+};
+
+enum rtw89_env_racing_lv {
+	RTW89_RAC_RELEASE = 0,
+	RTW89_RAC_LV_1 = 1,
+	RTW89_RAC_LV_2 = 2,
+	RTW89_RAC_LV_3 = 3,
+	RTW89_RAC_LV_4 = 4,
+	RTW89_RAC_MAX_NUM = 5
+};
+
+struct rtw89_ccx_para_info {
+	enum rtw89_env_racing_lv rac_lv;
+	u16 mntr_time;
+	u8 nhm_manual_th_ofst;
+	u8 nhm_manual_th0;
+	enum rtw89_ifs_clm_application ifs_clm_app;
+	u32 ifs_clm_manual_th_times;
+	u32 ifs_clm_manual_th0;
+	u8 fahm_manual_th_ofst;
+	u8 fahm_manual_th0;
+	u8 fahm_numer_opt;
+	u8 fahm_denom_opt;
+};
+
+enum rtw89_ccx_edcca_opt_sc_idx {
+	RTW89_CCX_EDCCA_SEG0_P0 = 0,
+	RTW89_CCX_EDCCA_SEG0_S1 = 1,
+	RTW89_CCX_EDCCA_SEG0_S2 = 2,
+	RTW89_CCX_EDCCA_SEG0_S3 = 3,
+	RTW89_CCX_EDCCA_SEG1_P0 = 4,
+	RTW89_CCX_EDCCA_SEG1_S1 = 5,
+	RTW89_CCX_EDCCA_SEG1_S2 = 6,
+	RTW89_CCX_EDCCA_SEG1_S3 = 7
+};
+
+enum rtw89_ccx_edcca_opt_bw_idx {
+	RTW89_CCX_EDCCA_BW20_0 = 0,
+	RTW89_CCX_EDCCA_BW20_1 = 1,
+	RTW89_CCX_EDCCA_BW20_2 = 2,
+	RTW89_CCX_EDCCA_BW20_3 = 3,
+	RTW89_CCX_EDCCA_BW20_4 = 4,
+	RTW89_CCX_EDCCA_BW20_5 = 5,
+	RTW89_CCX_EDCCA_BW20_6 = 6,
+	RTW89_CCX_EDCCA_BW20_7 = 7
+};
+
+#define RTW89_NHM_TH_NUM 11
+#define RTW89_FAHM_TH_NUM 11
+#define RTW89_NHM_RPT_NUM 12
+#define RTW89_FAHM_RPT_NUM 12
+#define RTW89_IFS_CLM_NUM 4
+struct rtw89_env_monitor_info {
+	u32 ccx_trigger_time;
+	u64 start_time;
+	u8 ccx_rpt_stamp;
+	u8 ccx_watchdog_result;
+	bool ccx_ongoing;
+	u8 ccx_rac_lv;
+	bool ccx_manual_ctrl;
+	u8 ccx_pre_rssi;
+	u16 clm_mntr_time;
+	u16 nhm_mntr_time;
+	u16 ifs_clm_mntr_time;
+	enum rtw89_ifs_clm_application ifs_clm_app;
+	u16 fahm_mntr_time;
+	u16 edcca_clm_mntr_time;
+	u16 ccx_period;
+	u8 ccx_unit_idx;
+	enum rtw89_ccx_edcca_opt_bw_idx ccx_edcca_opt_bw_idx;
+	u8 nhm_th[RTW89_NHM_TH_NUM];
+	u16 ifs_clm_th_l[RTW89_IFS_CLM_NUM];
+	u16 ifs_clm_th_h[RTW89_IFS_CLM_NUM];
+	u8 fahm_numer_opt;
+	u8 fahm_denom_opt;
+	u8 fahm_th[RTW89_FAHM_TH_NUM];
+	u16 clm_result;
+	u16 nhm_result[RTW89_NHM_RPT_NUM];
+	u8 nhm_wgt[RTW89_NHM_RPT_NUM];
+	u16 nhm_tx_cnt;
+	u16 nhm_cca_cnt;
+	u16 nhm_idle_cnt;
+	u16 ifs_clm_tx;
+	u16 ifs_clm_edcca_excl_cca;
+	u16 ifs_clm_ofdmfa;
+	u16 ifs_clm_ofdmcca_excl_fa;
+	u16 ifs_clm_cckfa;
+	u16 ifs_clm_cckcca_excl_fa;
+	u16 ifs_clm_total_ifs;
+	u8 ifs_clm_his[RTW89_IFS_CLM_NUM];
+	u16 ifs_clm_avg[RTW89_IFS_CLM_NUM];
+	u16 ifs_clm_cca[RTW89_IFS_CLM_NUM];
+	u16 fahm_result[RTW89_FAHM_RPT_NUM];
+	u16 fahm_denom_result;
+	u16 edcca_clm_result;
+	u8 clm_ratio;
+	u8 nhm_rpt[RTW89_NHM_RPT_NUM];
+	u8 nhm_tx_ratio;
+	u8 nhm_cca_ratio;
+	u8 nhm_idle_ratio;
+	u8 nhm_ratio;
+	u16 nhm_result_sum;
+	u8 nhm_pwr;
+	u8 ifs_clm_tx_ratio;
+	u8 ifs_clm_edcca_excl_cca_ratio;
+	u8 ifs_clm_cck_fa_ratio;
+	u8 ifs_clm_ofdm_fa_ratio;
+	u8 ifs_clm_cck_cca_excl_fa_ratio;
+	u8 ifs_clm_ofdm_cca_excl_fa_ratio;
+	u16 ifs_clm_cck_fa_permil;
+	u16 ifs_clm_ofdm_fa_permil;
+	u32 ifs_clm_ifs_avg[RTW89_IFS_CLM_NUM];
+	u32 ifs_clm_cca_avg[RTW89_IFS_CLM_NUM];
+	u8 fahm_rpt[RTW89_FAHM_RPT_NUM];
+	u16 fahm_result_sum;
+	u8 fahm_ratio;
+	u8 fahm_denom_ratio;
+	u8 fahm_pwr;
+	u8 edcca_clm_ratio;
+};
+
+enum rtw89_ser_rcvy_step {
+	RTW89_SER_DRV_STOP_TX,
+	RTW89_SER_DRV_STOP_RX,
+	RTW89_SER_DRV_STOP_RUN,
+	RTW89_SER_HAL_STOP_DMA,
+	RTW89_NUM_OF_SER_FLAGS
+};
+
+struct rtw89_ser {
+	u8 state;
+	u8 alarm_event;
+
+	struct work_struct ser_hdl_work;
+	struct delayed_work ser_alarm_work;
+	struct state_ent *st_tbl;
+	struct event_ent *ev_tbl;
+	struct list_head msg_q;
+	spinlock_t msg_q_lock; /* lock when read/write ser msg */
+	DECLARE_BITMAP(flags, RTW89_NUM_OF_SER_FLAGS);
+};
+
+enum rtw89_mac_ax_ps_mode {
+	RTW89_MAC_AX_PS_MODE_ACTIVE = 0,
+	RTW89_MAC_AX_PS_MODE_LEGACY = 1,
+	RTW89_MAC_AX_PS_MODE_WMMPS  = 2,
+	RTW89_MAC_AX_PS_MODE_MAX    = 3,
+};
+
+enum rtw89_last_rpwm_mode {
+	RTW89_LAST_RPWM_PS        = 0x0,
+	RTW89_LAST_RPWM_ACTIVE    = 0x6,
+};
+
+struct rtw89_lps_parm {
+	u8 macid;
+	u8 psmode; /* enum rtw89_mac_ax_ps_mode */
+	u8 lastrpwm; /* enum rtw89_last_rpwm_mode */
+};
+
+struct rtw89_ppdu_sts_info {
+	struct sk_buff_head rx_queue[RTW89_PHY_MAX];
+	u8 curr_rx_ppdu_cnt[RTW89_PHY_MAX];
+};
+
+struct rtw89_early_h2c {
+	struct list_head list;
+	u8 *h2c;
+	u16 h2c_len;
+};
+
+struct rtw89_dev {
+	struct ieee80211_hw *hw;
+	struct device *dev;
+
+	bool dbcc_en;
+	const struct rtw89_chip_info *chip;
+	struct rtw89_hal hal;
+	struct rtw89_mac_info mac;
+	struct rtw89_fw_info fw;
+	struct rtw89_hci_info hci;
+	struct rtw89_efuse efuse;
+	struct rtw89_traffic_stats stats;
+
+	/* ensures exclusive access from mac80211 callbacks */
+	struct mutex mutex;
+	struct list_head rtwvifs_list;
+	/* used to protect rf read write */
+	struct mutex rf_mutex;
+	struct workqueue_struct *txq_wq;
+	struct work_struct txq_work;
+	struct delayed_work txq_reinvoke_work;
+	/* used to protect ba_list */
+	spinlock_t ba_lock;
+	/* txqs to setup ba session */
+	struct list_head ba_list;
+	struct work_struct ba_work;
+
+	struct rtw89_cam_info cam_info;
+
+	struct sk_buff_head c2h_queue;
+	struct work_struct c2h_work;
+
+	struct list_head early_h2c_list;
+
+	struct rtw89_ser ser;
+
+	DECLARE_BITMAP(hw_port, RTW89_MAX_HW_PORT_NUM);
+	DECLARE_BITMAP(mac_id_map, RTW89_MAX_MAC_ID_NUM);
+	DECLARE_BITMAP(flags, NUM_OF_RTW89_FLAGS);
+
+	struct rtw89_phy_stat phystat;
+	struct rtw89_dack_info dack;
+	struct rtw89_iqk_info iqk;
+	struct rtw89_dpk_info dpk;
+	bool is_tssi_mode[RF_PATH_MAX];
+	bool is_bt_iqk_timeout;
+
+	struct rtw89_fem_info fem;
+	struct rtw89_txpwr_byrate byr[RTW89_BAND_MAX];
+	struct rtw89_tssi_info tssi;
+	struct rtw89_power_trim_info pwr_trim;
+
+	struct rtw89_cfo_tracking_info cfo_tracking;
+	struct rtw89_env_monitor_info env_monitor;
+	struct rtw89_dig_info dig;
+	struct rtw89_phy_ch_info ch_info;
+	struct delayed_work track_work;
+	struct delayed_work coex_act1_work;
+	struct delayed_work coex_bt_devinfo_work;
+	struct delayed_work coex_rfk_chk_work;
+	struct delayed_work cfo_track_work;
+	struct rtw89_ppdu_sts_info ppdu_sts;
+	u8 total_sta_assoc;
+	bool scanning;
+
+	const struct rtw89_regulatory *regd;
+	struct rtw89_sar_info sar;
+
+	struct rtw89_btc btc;
+	enum rtw89_ps_mode ps_mode;
+	bool lps_enabled;
+
+	/* napi structure */
+	struct net_device netdev;
+	struct napi_struct napi;
+	int napi_budget_countdown;
+
+	/* HCI related data, keep last */
+	u8 priv[0] __aligned(sizeof(void *));
+};
+
+static inline int rtw89_hci_tx_write(struct rtw89_dev *rtwdev,
+				     struct rtw89_core_tx_request *tx_req)
+{
+	return rtwdev->hci.ops->tx_write(rtwdev, tx_req);
+}
+
+static inline void rtw89_hci_reset(struct rtw89_dev *rtwdev)
+{
+	rtwdev->hci.ops->reset(rtwdev);
+}
+
+static inline int rtw89_hci_start(struct rtw89_dev *rtwdev)
+{
+	return rtwdev->hci.ops->start(rtwdev);
+}
+
+static inline void rtw89_hci_stop(struct rtw89_dev *rtwdev)
+{
+	rtwdev->hci.ops->stop(rtwdev);
+}
+
+static inline int rtw89_hci_deinit(struct rtw89_dev *rtwdev)
+{
+	return rtwdev->hci.ops->deinit(rtwdev);
+}
+
+static inline void rtw89_hci_recalc_int_mit(struct rtw89_dev *rtwdev)
+{
+	rtwdev->hci.ops->recalc_int_mit(rtwdev);
+}
+
+static inline u32 rtw89_hci_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev, u8 txch)
+{
+	return rtwdev->hci.ops->check_and_reclaim_tx_resource(rtwdev, txch);
+}
+
+static inline void rtw89_hci_tx_kick_off(struct rtw89_dev *rtwdev, u8 txch)
+{
+	return rtwdev->hci.ops->tx_kick_off(rtwdev, txch);
+}
+
+static inline void rtw89_hci_flush_queues(struct rtw89_dev *rtwdev, u32 queues,
+					  bool drop)
+{
+	if (rtwdev->hci.ops->flush_queues)
+		return rtwdev->hci.ops->flush_queues(rtwdev, queues, drop);
+}
+
+static inline u8 rtw89_read8(struct rtw89_dev *rtwdev, u32 addr)
+{
+	return rtwdev->hci.ops->read8(rtwdev, addr);
+}
+
+static inline u16 rtw89_read16(struct rtw89_dev *rtwdev, u32 addr)
+{
+	return rtwdev->hci.ops->read16(rtwdev, addr);
+}
+
+static inline u32 rtw89_read32(struct rtw89_dev *rtwdev, u32 addr)
+{
+	return rtwdev->hci.ops->read32(rtwdev, addr);
+}
+
+static inline void rtw89_write8(struct rtw89_dev *rtwdev, u32 addr, u8 data)
+{
+	rtwdev->hci.ops->write8(rtwdev, addr, data);
+}
+
+static inline void rtw89_write16(struct rtw89_dev *rtwdev, u32 addr, u16 data)
+{
+	rtwdev->hci.ops->write16(rtwdev, addr, data);
+}
+
+static inline void rtw89_write32(struct rtw89_dev *rtwdev, u32 addr, u32 data)
+{
+	rtwdev->hci.ops->write32(rtwdev, addr, data);
+}
+
+static inline void
+rtw89_write8_set(struct rtw89_dev *rtwdev, u32 addr, u8 bit)
+{
+	u8 val;
+
+	val = rtw89_read8(rtwdev, addr);
+	rtw89_write8(rtwdev, addr, val | bit);
+}
+
+static inline void
+rtw89_write16_set(struct rtw89_dev *rtwdev, u32 addr, u16 bit)
+{
+	u16 val;
+
+	val = rtw89_read16(rtwdev, addr);
+	rtw89_write16(rtwdev, addr, val | bit);
+}
+
+static inline void
+rtw89_write32_set(struct rtw89_dev *rtwdev, u32 addr, u32 bit)
+{
+	u32 val;
+
+	val = rtw89_read32(rtwdev, addr);
+	rtw89_write32(rtwdev, addr, val | bit);
+}
+
+static inline void
+rtw89_write8_clr(struct rtw89_dev *rtwdev, u32 addr, u8 bit)
+{
+	u8 val;
+
+	val = rtw89_read8(rtwdev, addr);
+	rtw89_write8(rtwdev, addr, val & ~bit);
+}
+
+static inline void
+rtw89_write16_clr(struct rtw89_dev *rtwdev, u32 addr, u16 bit)
+{
+	u16 val;
+
+	val = rtw89_read16(rtwdev, addr);
+	rtw89_write16(rtwdev, addr, val & ~bit);
+}
+
+static inline void
+rtw89_write32_clr(struct rtw89_dev *rtwdev, u32 addr, u32 bit)
+{
+	u32 val;
+
+	val = rtw89_read32(rtwdev, addr);
+	rtw89_write32(rtwdev, addr, val & ~bit);
+}
+
+static inline u32
+rtw89_read32_mask(struct rtw89_dev *rtwdev, u32 addr, u32 mask)
+{
+	u32 shift = __ffs(mask);
+	u32 orig;
+	u32 ret;
+
+	orig = rtw89_read32(rtwdev, addr);
+	ret = (orig & mask) >> shift;
+
+	return ret;
+}
+
+static inline u16
+rtw89_read16_mask(struct rtw89_dev *rtwdev, u32 addr, u32 mask)
+{
+	u32 shift = __ffs(mask);
+	u32 orig;
+	u32 ret;
+
+	orig = rtw89_read16(rtwdev, addr);
+	ret = (orig & mask) >> shift;
+
+	return ret;
+}
+
+static inline u8
+rtw89_read8_mask(struct rtw89_dev *rtwdev, u32 addr, u32 mask)
+{
+	u32 shift = __ffs(mask);
+	u32 orig;
+	u32 ret;
+
+	orig = rtw89_read8(rtwdev, addr);
+	ret = (orig & mask) >> shift;
+
+	return ret;
+}
+
+static inline void
+rtw89_write32_mask(struct rtw89_dev *rtwdev, u32 addr, u32 mask, u32 data)
+{
+	u32 shift = __ffs(mask);
+	u32 orig;
+	u32 set;
+
+	WARN(addr & 0x3, "should be 4-byte aligned, addr = 0x%08x\n", addr);
+
+	orig = rtw89_read32(rtwdev, addr);
+	set = (orig & ~mask) | ((data << shift) & mask);
+	rtw89_write32(rtwdev, addr, set);
+}
+
+static inline void
+rtw89_write16_mask(struct rtw89_dev *rtwdev, u32 addr, u32 mask, u16 data)
+{
+	u32 shift;
+	u16 orig, set;
+
+	mask &= 0xffff;
+	shift = __ffs(mask);
+
+	orig = rtw89_read16(rtwdev, addr);
+	set = (orig & ~mask) | ((data << shift) & mask);
+	rtw89_write16(rtwdev, addr, set);
+}
+
+static inline void
+rtw89_write8_mask(struct rtw89_dev *rtwdev, u32 addr, u32 mask, u8 data)
+{
+	u32 shift;
+	u8 orig, set;
+
+	mask &= 0xff;
+	shift = __ffs(mask);
+
+	orig = rtw89_read8(rtwdev, addr);
+	set = (orig & ~mask) | ((data << shift) & mask);
+	rtw89_write8(rtwdev, addr, set);
+}
+
+static inline u32
+rtw89_read_rf(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+	      u32 addr, u32 mask)
+{
+	u32 val;
+
+	mutex_lock(&rtwdev->rf_mutex);
+	val = rtwdev->chip->ops->read_rf(rtwdev, rf_path, addr, mask);
+	mutex_unlock(&rtwdev->rf_mutex);
+
+	return val;
+}
+
+static inline void
+rtw89_write_rf(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+	       u32 addr, u32 mask, u32 data)
+{
+	mutex_lock(&rtwdev->rf_mutex);
+	rtwdev->chip->ops->write_rf(rtwdev, rf_path, addr, mask, data);
+	mutex_unlock(&rtwdev->rf_mutex);
+}
+
+static inline struct ieee80211_txq *rtw89_txq_to_txq(struct rtw89_txq *rtwtxq)
+{
+	void *p = rtwtxq;
+
+	return container_of(p, struct ieee80211_txq, drv_priv);
+}
+
+static inline void rtw89_core_txq_init(struct rtw89_dev *rtwdev,
+				       struct ieee80211_txq *txq)
+{
+	struct rtw89_txq *rtwtxq;
+
+	if (!txq)
+		return;
+
+	rtwtxq = (struct rtw89_txq *)txq->drv_priv;
+	INIT_LIST_HEAD(&rtwtxq->list);
+}
+
+static inline struct ieee80211_vif *rtwvif_to_vif(struct rtw89_vif *rtwvif)
+{
+	void *p = rtwvif;
+
+	return container_of(p, struct ieee80211_vif, drv_priv);
+}
+
+static inline struct ieee80211_sta *rtwsta_to_sta(struct rtw89_sta *rtwsta)
+{
+	void *p = rtwsta;
+
+	return container_of(p, struct ieee80211_sta, drv_priv);
+}
+
+static inline
+void rtw89_chip_set_channel_prepare(struct rtw89_dev *rtwdev,
+				    struct rtw89_channel_help_params *p)
+{
+	rtwdev->chip->ops->set_channel_help(rtwdev, true, p);
+}
+
+static inline
+void rtw89_chip_set_channel_done(struct rtw89_dev *rtwdev,
+				 struct rtw89_channel_help_params *p)
+{
+	rtwdev->chip->ops->set_channel_help(rtwdev, false, p);
+}
+
+static inline void rtw89_chip_fem_setup(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->fem_setup)
+		chip->ops->fem_setup(rtwdev);
+}
+
+static inline void rtw89_chip_bb_sethw(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->bb_sethw)
+		chip->ops->bb_sethw(rtwdev);
+}
+
+static inline void rtw89_chip_rfk_init(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->rfk_init)
+		chip->ops->rfk_init(rtwdev);
+}
+
+static inline void rtw89_chip_rfk_channel(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->rfk_channel)
+		chip->ops->rfk_channel(rtwdev);
+}
+
+static inline void rtw89_chip_rfk_band_changed(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->rfk_band_changed)
+		chip->ops->rfk_band_changed(rtwdev);
+}
+
+static inline void rtw89_chip_rfk_scan(struct rtw89_dev *rtwdev, bool start)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->rfk_scan)
+		chip->ops->rfk_scan(rtwdev, start);
+}
+
+static inline void rtw89_chip_rfk_track(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->rfk_track)
+		chip->ops->rfk_track(rtwdev);
+}
+
+static inline void rtw89_chip_set_txpwr_ctrl(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->set_txpwr_ctrl)
+		chip->ops->set_txpwr_ctrl(rtwdev);
+}
+
+static inline void rtw89_chip_set_txpwr(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	u8 ch = rtwdev->hal.current_channel;
+
+	if (!ch)
+		return;
+
+	if (chip->ops->set_txpwr)
+		chip->ops->set_txpwr(rtwdev);
+}
+
+static inline void rtw89_chip_power_trim(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->power_trim)
+		chip->ops->power_trim(rtwdev);
+}
+
+static inline void rtw89_chip_init_txpwr_unit(struct rtw89_dev *rtwdev,
+					      enum rtw89_phy_idx phy_idx)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->init_txpwr_unit)
+		chip->ops->init_txpwr_unit(rtwdev, phy_idx);
+}
+
+static inline u8 rtw89_chip_get_thermal(struct rtw89_dev *rtwdev,
+					enum rtw89_rf_path rf_path)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (!chip->ops->get_thermal)
+		return 0x10;
+
+	return chip->ops->get_thermal(rtwdev, rf_path);
+}
+
+static inline void rtw89_chip_query_ppdu(struct rtw89_dev *rtwdev,
+					 struct rtw89_rx_phy_ppdu *phy_ppdu,
+					 struct ieee80211_rx_status *status)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->query_ppdu)
+		chip->ops->query_ppdu(rtwdev, phy_ppdu, status);
+}
+
+static inline void rtw89_chip_bb_ctrl_btc_preagc(struct rtw89_dev *rtwdev,
+						 bool bt_en)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->bb_ctrl_btc_preagc)
+		chip->ops->bb_ctrl_btc_preagc(rtwdev, bt_en);
+}
+
+static inline
+void rtw89_chip_cfg_txpwr_ul_tb_offset(struct rtw89_dev *rtwdev,
+				       struct ieee80211_vif *vif)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (!vif->bss_conf.he_support || !vif->bss_conf.assoc)
+		return;
+
+	if (chip->ops->set_txpwr_ul_tb_offset)
+		chip->ops->set_txpwr_ul_tb_offset(rtwdev, 0, rtwvif->mac_idx);
+}
+
+static inline void rtw89_load_txpwr_table(struct rtw89_dev *rtwdev,
+					  const struct rtw89_txpwr_table *tbl)
+{
+	tbl->load(rtwdev, tbl);
+}
+
+static inline u8 rtw89_regd_get(struct rtw89_dev *rtwdev, u8 band)
+{
+	return rtwdev->regd->txpwr_regd[band];
+}
+
+static inline void rtw89_ctrl_btg(struct rtw89_dev *rtwdev, bool btg)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	if (chip->ops->ctrl_btg)
+		chip->ops->ctrl_btg(rtwdev, btg);
+}
+
+static inline u8 *get_hdr_bssid(struct ieee80211_hdr *hdr)
+{
+	__le16 fc = hdr->frame_control;
+
+	if (ieee80211_has_tods(fc))
+		return hdr->addr1;
+	else if (ieee80211_has_fromds(fc))
+		return hdr->addr2;
+	else
+		return hdr->addr3;
+}
+
+static inline bool rtw89_sta_has_beamformer_cap(struct ieee80211_sta *sta)
+{
+	if ((sta->vht_cap.cap & IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE) ||
+	    (sta->vht_cap.cap & IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE) ||
+	    (sta->he_cap.he_cap_elem.phy_cap_info[3] & IEEE80211_HE_PHY_CAP3_SU_BEAMFORMER) ||
+	    (sta->he_cap.he_cap_elem.phy_cap_info[4] & IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER))
+		return true;
+	return false;
+}
+
+static inline struct rtw89_fw_suit *rtw89_fw_suit_get(struct rtw89_dev *rtwdev,
+						      enum rtw89_fw_type type)
+{
+	struct rtw89_fw_info *fw_info = &rtwdev->fw;
+
+	if (type == RTW89_FW_WOWLAN)
+		return &fw_info->wowlan;
+	return &fw_info->normal;
+}
+
+int rtw89_core_tx_write(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+			struct ieee80211_sta *sta, struct sk_buff *skb, int *qsel);
+int rtw89_h2c_tx(struct rtw89_dev *rtwdev,
+		 struct sk_buff *skb, bool fwdl);
+void rtw89_core_tx_kick_off(struct rtw89_dev *rtwdev, u8 qsel);
+void rtw89_core_fill_txdesc(struct rtw89_dev *rtwdev,
+			    struct rtw89_tx_desc_info *desc_info,
+			    void *txdesc);
+void rtw89_core_rx(struct rtw89_dev *rtwdev,
+		   struct rtw89_rx_desc_info *desc_info,
+		   struct sk_buff *skb);
+void rtw89_core_query_rxdesc(struct rtw89_dev *rtwdev,
+			     struct rtw89_rx_desc_info *desc_info,
+			     u8 *data, u32 data_offset);
+void rtw89_core_napi_start(struct rtw89_dev *rtwdev);
+void rtw89_core_napi_stop(struct rtw89_dev *rtwdev);
+void rtw89_core_napi_init(struct rtw89_dev *rtwdev);
+void rtw89_core_napi_deinit(struct rtw89_dev *rtwdev);
+int rtw89_core_sta_add(struct rtw89_dev *rtwdev,
+		       struct ieee80211_vif *vif,
+		       struct ieee80211_sta *sta);
+int rtw89_core_sta_assoc(struct rtw89_dev *rtwdev,
+			 struct ieee80211_vif *vif,
+			 struct ieee80211_sta *sta);
+int rtw89_core_sta_disassoc(struct rtw89_dev *rtwdev,
+			    struct ieee80211_vif *vif,
+			    struct ieee80211_sta *sta);
+int rtw89_core_sta_disconnect(struct rtw89_dev *rtwdev,
+			      struct ieee80211_vif *vif,
+			      struct ieee80211_sta *sta);
+int rtw89_core_sta_remove(struct rtw89_dev *rtwdev,
+			  struct ieee80211_vif *vif,
+			  struct ieee80211_sta *sta);
+int rtw89_core_init(struct rtw89_dev *rtwdev);
+void rtw89_core_deinit(struct rtw89_dev *rtwdev);
+int rtw89_core_register(struct rtw89_dev *rtwdev);
+void rtw89_core_unregister(struct rtw89_dev *rtwdev);
+void rtw89_set_channel(struct rtw89_dev *rtwdev);
+u8 rtw89_core_acquire_bit_map(unsigned long *addr, unsigned long size);
+void rtw89_core_release_bit_map(unsigned long *addr, u8 bit);
+void rtw89_core_release_all_bits_map(unsigned long *addr, unsigned int nbits);
+void rtw89_vif_type_mapping(struct ieee80211_vif *vif, bool assoc);
+int rtw89_chip_info_setup(struct rtw89_dev *rtwdev);
+u16 rtw89_ra_report_to_bitrate(struct rtw89_dev *rtwdev, u8 rpt_rate);
+int rtw89_regd_init(struct rtw89_dev *rtwdev,
+		    void (*reg_notifier)(struct wiphy *wiphy, struct regulatory_request *request));
+void rtw89_regd_notifier(struct wiphy *wiphy, struct regulatory_request *request);
+void rtw89_traffic_stats_init(struct rtw89_dev *rtwdev,
+			      struct rtw89_traffic_stats *stats);
+int rtw89_core_start(struct rtw89_dev *rtwdev);
+void rtw89_core_stop(struct rtw89_dev *rtwdev);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/debug.c
@@ -0,0 +1,2489 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "coex.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+#include "ps.h"
+#include "reg.h"
+#include "sar.h"
+
+#ifdef CONFIG_RTW89_DEBUGMSG
+unsigned int rtw89_debug_mask;
+EXPORT_SYMBOL(rtw89_debug_mask);
+module_param_named(debug_mask, rtw89_debug_mask, uint, 0644);
+MODULE_PARM_DESC(debug_mask, "Debugging mask");
+#endif
+
+#ifdef CONFIG_RTW89_DEBUGFS
+struct rtw89_debugfs_priv {
+	struct rtw89_dev *rtwdev;
+	int (*cb_read)(struct seq_file *m, void *v);
+	ssize_t (*cb_write)(struct file *filp, const char __user *buffer,
+			    size_t count, loff_t *loff);
+	union {
+		u32 cb_data;
+		struct {
+			u32 addr;
+			u8 len;
+		} read_reg;
+		struct {
+			u32 addr;
+			u32 mask;
+			u8 path;
+		} read_rf;
+		struct {
+			u8 ss_dbg:1;
+			u8 dle_dbg:1;
+			u8 dmac_dbg:1;
+			u8 cmac_dbg:1;
+			u8 dbg_port:1;
+		} dbgpkg_en;
+		struct {
+			u32 start;
+			u32 len;
+			u8 sel;
+		} mac_mem;
+	};
+};
+
+static int rtw89_debugfs_single_show(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+
+	return debugfs_priv->cb_read(m, v);
+}
+
+static ssize_t rtw89_debugfs_single_write(struct file *filp,
+					  const char __user *buffer,
+					  size_t count, loff_t *loff)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = filp->private_data;
+
+	return debugfs_priv->cb_write(filp, buffer, count, loff);
+}
+
+static ssize_t rtw89_debugfs_seq_file_write(struct file *filp,
+					    const char __user *buffer,
+					    size_t count, loff_t *loff)
+{
+	struct seq_file *seqpriv = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = seqpriv->private;
+
+	return debugfs_priv->cb_write(filp, buffer, count, loff);
+}
+
+static int rtw89_debugfs_single_open(struct inode *inode, struct file *filp)
+{
+	return single_open(filp, rtw89_debugfs_single_show, inode->i_private);
+}
+
+static int rtw89_debugfs_close(struct inode *inode, struct file *filp)
+{
+	return 0;
+}
+
+static const struct file_operations file_ops_single_r = {
+	.owner = THIS_MODULE,
+	.open = rtw89_debugfs_single_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+
+static const struct file_operations file_ops_common_rw = {
+	.owner = THIS_MODULE,
+	.open = rtw89_debugfs_single_open,
+	.release = single_release,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.write = rtw89_debugfs_seq_file_write,
+};
+
+static const struct file_operations file_ops_single_w = {
+	.owner = THIS_MODULE,
+	.write = rtw89_debugfs_single_write,
+	.open = simple_open,
+	.release = rtw89_debugfs_close,
+};
+
+static ssize_t
+rtw89_debug_priv_read_reg_select(struct file *filp,
+				 const char __user *user_buf,
+				 size_t count, loff_t *loff)
+{
+	struct seq_file *m = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	u32 addr, len;
+	int num;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	num = sscanf(buf, "%x %x", &addr, &len);
+	if (num != 2) {
+		rtw89_info(rtwdev, "invalid format: <addr> <len>\n");
+		return -EINVAL;
+	}
+
+	debugfs_priv->read_reg.addr = addr;
+	debugfs_priv->read_reg.len = len;
+
+	rtw89_info(rtwdev, "select read %d bytes from 0x%08x\n", len, addr);
+
+	return count;
+}
+
+static int rtw89_debug_priv_read_reg_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	u32 addr, data;
+	u8 len;
+
+	len = debugfs_priv->read_reg.len;
+	addr = debugfs_priv->read_reg.addr;
+
+	switch (len) {
+	case 1:
+		data = rtw89_read8(rtwdev, addr);
+		break;
+	case 2:
+		data = rtw89_read16(rtwdev, addr);
+		break;
+	case 4:
+		data = rtw89_read32(rtwdev, addr);
+		break;
+	default:
+		rtw89_info(rtwdev, "invalid read reg len %d\n", len);
+		return -EINVAL;
+	}
+
+	seq_printf(m, "get %d bytes at 0x%08x=0x%08x\n", len, addr, data);
+
+	return 0;
+}
+
+static ssize_t rtw89_debug_priv_write_reg_set(struct file *filp,
+					      const char __user *user_buf,
+					      size_t count, loff_t *loff)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = filp->private_data;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	u32 addr, val, len;
+	int num;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	num = sscanf(buf, "%x %x %x", &addr, &val, &len);
+	if (num !=  3) {
+		rtw89_info(rtwdev, "invalid format: <addr> <val> <len>\n");
+		return -EINVAL;
+	}
+
+	switch (len) {
+	case 1:
+		rtw89_info(rtwdev, "reg write8 0x%08x: 0x%02x\n", addr, val);
+		rtw89_write8(rtwdev, addr, (u8)val);
+		break;
+	case 2:
+		rtw89_info(rtwdev, "reg write16 0x%08x: 0x%04x\n", addr, val);
+		rtw89_write16(rtwdev, addr, (u16)val);
+		break;
+	case 4:
+		rtw89_info(rtwdev, "reg write32 0x%08x: 0x%08x\n", addr, val);
+		rtw89_write32(rtwdev, addr, (u32)val);
+		break;
+	default:
+		rtw89_info(rtwdev, "invalid read write len %d\n", len);
+		break;
+	}
+
+	return count;
+}
+
+static ssize_t
+rtw89_debug_priv_read_rf_select(struct file *filp,
+				const char __user *user_buf,
+				size_t count, loff_t *loff)
+{
+	struct seq_file *m = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	u32 addr, mask;
+	u8 path;
+	int num;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	num = sscanf(buf, "%hhd %x %x", &path, &addr, &mask);
+	if (num != 3) {
+		rtw89_info(rtwdev, "invalid format: <path> <addr> <mask>\n");
+		return -EINVAL;
+	}
+
+	if (path >= rtwdev->chip->rf_path_num) {
+		rtw89_info(rtwdev, "wrong rf path\n");
+		return -EINVAL;
+	}
+	debugfs_priv->read_rf.addr = addr;
+	debugfs_priv->read_rf.mask = mask;
+	debugfs_priv->read_rf.path = path;
+
+	rtw89_info(rtwdev, "select read rf path %d from 0x%08x\n", path, addr);
+
+	return count;
+}
+
+static int rtw89_debug_priv_read_rf_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	u32 addr, data, mask;
+	u8 path;
+
+	addr = debugfs_priv->read_rf.addr;
+	mask = debugfs_priv->read_rf.mask;
+	path = debugfs_priv->read_rf.path;
+
+	data = rtw89_read_rf(rtwdev, path, addr, mask);
+
+	seq_printf(m, "path %d, rf register 0x%08x=0x%08x\n", path, addr, data);
+
+	return 0;
+}
+
+static ssize_t rtw89_debug_priv_write_rf_set(struct file *filp,
+					     const char __user *user_buf,
+					     size_t count, loff_t *loff)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = filp->private_data;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	u32 addr, val, mask;
+	u8 path;
+	int num;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	num = sscanf(buf, "%hhd %x %x %x", &path, &addr, &mask, &val);
+	if (num != 4) {
+		rtw89_info(rtwdev, "invalid format: <path> <addr> <mask> <val>\n");
+		return -EINVAL;
+	}
+
+	if (path >= rtwdev->chip->rf_path_num) {
+		rtw89_info(rtwdev, "wrong rf path\n");
+		return -EINVAL;
+	}
+
+	rtw89_info(rtwdev, "path %d, rf register write 0x%08x=0x%08x (mask = 0x%08x)\n",
+		   path, addr, val, mask);
+	rtw89_write_rf(rtwdev, path, addr, mask, val);
+
+	return count;
+}
+
+static int rtw89_debug_priv_rf_reg_dump_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	u32 addr, offset, data;
+	u8 path;
+
+	for (path = 0; path < chip->rf_path_num; path++) {
+		seq_printf(m, "RF path %d:\n\n", path);
+		for (addr = 0; addr < 0x100; addr += 4) {
+			seq_printf(m, "0x%08x: ", addr);
+			for (offset = 0; offset < 4; offset++) {
+				data = rtw89_read_rf(rtwdev, path,
+						     addr + offset, RFREG_MASK);
+				seq_printf(m, "0x%05x  ", data);
+			}
+			seq_puts(m, "\n");
+		}
+		seq_puts(m, "\n");
+	}
+
+	return 0;
+}
+
+struct txpwr_ent {
+	const char *txt;
+	u8 len;
+};
+
+struct txpwr_map {
+	const struct txpwr_ent *ent;
+	u8 size;
+	u32 addr_from;
+	u32 addr_to;
+};
+
+#define __GEN_TXPWR_ENT2(_t, _e0, _e1) \
+	{ .len = 2, .txt = _t "\t-  " _e0 "  " _e1 }
+
+#define __GEN_TXPWR_ENT4(_t, _e0, _e1, _e2, _e3) \
+	{ .len = 4, .txt = _t "\t-  " _e0 "  " _e1 "  " _e2 "  " _e3 }
+
+#define __GEN_TXPWR_ENT8(_t, _e0, _e1, _e2, _e3, _e4, _e5, _e6, _e7) \
+	{ .len = 8, .txt = _t "\t-  " \
+	  _e0 "  " _e1 "  " _e2 "  " _e3 "  " \
+	  _e4 "  " _e5 "  " _e6 "  " _e7 }
+
+static const struct txpwr_ent __txpwr_ent_byr[] = {
+	__GEN_TXPWR_ENT4("CCK       ", "1M   ", "2M   ", "5.5M ", "11M  "),
+	__GEN_TXPWR_ENT4("LEGACY    ", "6M   ", "9M   ", "12M  ", "18M  "),
+	__GEN_TXPWR_ENT4("LEGACY    ", "24M  ", "36M  ", "48M  ", "54M  "),
+	/* 1NSS */
+	__GEN_TXPWR_ENT4("MCS_1NSS  ", "MCS0 ", "MCS1 ", "MCS2 ", "MCS3 "),
+	__GEN_TXPWR_ENT4("MCS_1NSS  ", "MCS4 ", "MCS5 ", "MCS6 ", "MCS7 "),
+	__GEN_TXPWR_ENT4("MCS_1NSS  ", "MCS8 ", "MCS9 ", "MCS10", "MCS11"),
+	__GEN_TXPWR_ENT4("HEDCM_1NSS", "MCS0 ", "MCS1 ", "MCS3 ", "MCS4 "),
+	/* 2NSS */
+	__GEN_TXPWR_ENT4("MCS_2NSS  ", "MCS0 ", "MCS1 ", "MCS2 ", "MCS3 "),
+	__GEN_TXPWR_ENT4("MCS_2NSS  ", "MCS4 ", "MCS5 ", "MCS6 ", "MCS7 "),
+	__GEN_TXPWR_ENT4("MCS_2NSS  ", "MCS8 ", "MCS9 ", "MCS10", "MCS11"),
+	__GEN_TXPWR_ENT4("HEDCM_2NSS", "MCS0 ", "MCS1 ", "MCS3 ", "MCS4 "),
+};
+
+static_assert((ARRAY_SIZE(__txpwr_ent_byr) * 4) ==
+	(R_AX_PWR_BY_RATE_MAX - R_AX_PWR_BY_RATE + 4));
+
+static const struct txpwr_map __txpwr_map_byr = {
+	.ent = __txpwr_ent_byr,
+	.size = ARRAY_SIZE(__txpwr_ent_byr),
+	.addr_from = R_AX_PWR_BY_RATE,
+	.addr_to = R_AX_PWR_BY_RATE_MAX,
+};
+
+static const struct txpwr_ent __txpwr_ent_lmt[] = {
+	/* 1TX */
+	__GEN_TXPWR_ENT2("CCK_1TX_20M    ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("CCK_1TX_40M    ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("OFDM_1TX       ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_0  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_1  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_2  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_3  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_4  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_5  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_6  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_20M_7  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_40M_0  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_40M_1  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_40M_2  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_40M_3  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_80M_0  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_80M_1  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_160M   ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_40M_0p5", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_1TX_40M_2p5", "NON_BF", "BF"),
+	/* 2TX */
+	__GEN_TXPWR_ENT2("CCK_2TX_20M    ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("CCK_2TX_40M    ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("OFDM_2TX       ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_0  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_1  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_2  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_3  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_4  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_5  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_6  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_20M_7  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_40M_0  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_40M_1  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_40M_2  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_40M_3  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_80M_0  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_80M_1  ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_160M   ", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_40M_0p5", "NON_BF", "BF"),
+	__GEN_TXPWR_ENT2("MCS_2TX_40M_2p5", "NON_BF", "BF"),
+};
+
+static_assert((ARRAY_SIZE(__txpwr_ent_lmt) * 2) ==
+	(R_AX_PWR_LMT_MAX - R_AX_PWR_LMT + 4));
+
+static const struct txpwr_map __txpwr_map_lmt = {
+	.ent = __txpwr_ent_lmt,
+	.size = ARRAY_SIZE(__txpwr_ent_lmt),
+	.addr_from = R_AX_PWR_LMT,
+	.addr_to = R_AX_PWR_LMT_MAX,
+};
+
+static const struct txpwr_ent __txpwr_ent_lmt_ru[] = {
+	/* 1TX */
+	__GEN_TXPWR_ENT8("1TX", "RU26__0", "RU26__1", "RU26__2", "RU26__3",
+			 "RU26__4", "RU26__5", "RU26__6", "RU26__7"),
+	__GEN_TXPWR_ENT8("1TX", "RU52__0", "RU52__1", "RU52__2", "RU52__3",
+			 "RU52__4", "RU52__5", "RU52__6", "RU52__7"),
+	__GEN_TXPWR_ENT8("1TX", "RU106_0", "RU106_1", "RU106_2", "RU106_3",
+			 "RU106_4", "RU106_5", "RU106_6", "RU106_7"),
+	/* 2TX */
+	__GEN_TXPWR_ENT8("2TX", "RU26__0", "RU26__1", "RU26__2", "RU26__3",
+			 "RU26__4", "RU26__5", "RU26__6", "RU26__7"),
+	__GEN_TXPWR_ENT8("2TX", "RU52__0", "RU52__1", "RU52__2", "RU52__3",
+			 "RU52__4", "RU52__5", "RU52__6", "RU52__7"),
+	__GEN_TXPWR_ENT8("2TX", "RU106_0", "RU106_1", "RU106_2", "RU106_3",
+			 "RU106_4", "RU106_5", "RU106_6", "RU106_7"),
+};
+
+static_assert((ARRAY_SIZE(__txpwr_ent_lmt_ru) * 8) ==
+	(R_AX_PWR_RU_LMT_MAX - R_AX_PWR_RU_LMT + 4));
+
+static const struct txpwr_map __txpwr_map_lmt_ru = {
+	.ent = __txpwr_ent_lmt_ru,
+	.size = ARRAY_SIZE(__txpwr_ent_lmt_ru),
+	.addr_from = R_AX_PWR_RU_LMT,
+	.addr_to = R_AX_PWR_RU_LMT_MAX,
+};
+
+static u8 __print_txpwr_ent(struct seq_file *m, const struct txpwr_ent *ent,
+			    const u8 *buf, const u8 cur)
+{
+	char *fmt;
+
+	switch (ent->len) {
+	case 2:
+		fmt = "%s\t| %3d, %3d,\tdBm\n";
+		seq_printf(m, fmt, ent->txt, buf[cur], buf[cur + 1]);
+		return 2;
+	case 4:
+		fmt = "%s\t| %3d, %3d, %3d, %3d,\tdBm\n";
+		seq_printf(m, fmt, ent->txt, buf[cur], buf[cur + 1],
+			   buf[cur + 2], buf[cur + 3]);
+		return 4;
+	case 8:
+		fmt = "%s\t| %3d, %3d, %3d, %3d, %3d, %3d, %3d, %3d,\tdBm\n";
+		seq_printf(m, fmt, ent->txt, buf[cur], buf[cur + 1],
+			   buf[cur + 2], buf[cur + 3], buf[cur + 4],
+			   buf[cur + 5], buf[cur + 6], buf[cur + 7]);
+		return 8;
+	default:
+		return 0;
+	}
+}
+
+static int __print_txpwr_map(struct seq_file *m, struct rtw89_dev *rtwdev,
+			     const struct txpwr_map *map)
+{
+	u8 fct = rtwdev->chip->txpwr_factor_mac;
+	u8 *buf, cur, i;
+	u32 val, addr;
+	int ret;
+
+	buf = vzalloc(map->addr_to - map->addr_from + 4);
+	if (!buf)
+		return -ENOMEM;
+
+	for (addr = map->addr_from; addr <= map->addr_to; addr += 4) {
+		ret = rtw89_mac_txpwr_read32(rtwdev, RTW89_PHY_0, addr, &val);
+		if (ret)
+			val = MASKDWORD;
+
+		cur = addr - map->addr_from;
+		for (i = 0; i < 4; i++, val >>= 8)
+			buf[cur + i] = FIELD_GET(MASKBYTE0, val) >> fct;
+	}
+
+	for (cur = 0, i = 0; i < map->size; i++)
+		cur += __print_txpwr_ent(m, &map->ent[i], buf, cur);
+
+	vfree(buf);
+	return 0;
+}
+
+#define case_REGD(_regd) \
+	case RTW89_ ## _regd: \
+		seq_puts(m, #_regd "\n"); \
+		break
+
+static void __print_regd(struct seq_file *m, struct rtw89_dev *rtwdev)
+{
+	u8 band = rtwdev->hal.current_band_type;
+	u8 regd = rtw89_regd_get(rtwdev, band);
+
+	switch (regd) {
+	default:
+		seq_printf(m, "UNKNOWN: %d\n", regd);
+		break;
+	case_REGD(WW);
+	case_REGD(ETSI);
+	case_REGD(FCC);
+	case_REGD(MKK);
+	case_REGD(NA);
+	case_REGD(IC);
+	case_REGD(KCC);
+	case_REGD(NCC);
+	case_REGD(CHILE);
+	case_REGD(ACMA);
+	case_REGD(MEXICO);
+	case_REGD(UKRAINE);
+	case_REGD(CN);
+	}
+}
+
+#undef case_REGD
+
+static int rtw89_debug_priv_txpwr_table_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	int ret = 0;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+
+	seq_puts(m, "[Regulatory] ");
+	__print_regd(m, rtwdev);
+
+	seq_puts(m, "[SAR]\n");
+	rtw89_print_sar(m, rtwdev);
+
+	seq_puts(m, "\n[TX power byrate]\n");
+	ret = __print_txpwr_map(m, rtwdev, &__txpwr_map_byr);
+	if (ret)
+		goto err;
+
+	seq_puts(m, "\n[TX power limit]\n");
+	ret = __print_txpwr_map(m, rtwdev, &__txpwr_map_lmt);
+	if (ret)
+		goto err;
+
+	seq_puts(m, "\n[TX power limit_ru]\n");
+	ret = __print_txpwr_map(m, rtwdev, &__txpwr_map_lmt_ru);
+	if (ret)
+		goto err;
+
+err:
+	mutex_unlock(&rtwdev->mutex);
+	return ret;
+}
+
+static ssize_t
+rtw89_debug_priv_mac_reg_dump_select(struct file *filp,
+				     const char __user *user_buf,
+				     size_t count, loff_t *loff)
+{
+	struct seq_file *m = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	int sel;
+	int ret;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	ret = kstrtoint(buf, 0, &sel);
+	if (ret)
+		return ret;
+
+	if (sel < RTW89_DBG_SEL_MAC_00 || sel > RTW89_DBG_SEL_RFC) {
+		rtw89_info(rtwdev, "invalid args: %d\n", sel);
+		return -EINVAL;
+	}
+
+	debugfs_priv->cb_data = sel;
+	rtw89_info(rtwdev, "select mac page dump %d\n", debugfs_priv->cb_data);
+
+	return count;
+}
+
+#define RTW89_MAC_PAGE_SIZE		0x100
+
+static int rtw89_debug_priv_mac_reg_dump_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	enum rtw89_debug_mac_reg_sel reg_sel = debugfs_priv->cb_data;
+	u32 start, end;
+	u32 i, j, k, page;
+	u32 val;
+
+	switch (reg_sel) {
+	case RTW89_DBG_SEL_MAC_00:
+		seq_puts(m, "Debug selected MAC page 0x00\n");
+		start = 0x000;
+		end = 0x014;
+		break;
+	case RTW89_DBG_SEL_MAC_40:
+		seq_puts(m, "Debug selected MAC page 0x40\n");
+		start = 0x040;
+		end = 0x07f;
+		break;
+	case RTW89_DBG_SEL_MAC_80:
+		seq_puts(m, "Debug selected MAC page 0x80\n");
+		start = 0x080;
+		end = 0x09f;
+		break;
+	case RTW89_DBG_SEL_MAC_C0:
+		seq_puts(m, "Debug selected MAC page 0xc0\n");
+		start = 0x0c0;
+		end = 0x0df;
+		break;
+	case RTW89_DBG_SEL_MAC_E0:
+		seq_puts(m, "Debug selected MAC page 0xe0\n");
+		start = 0x0e0;
+		end = 0x0ff;
+		break;
+	case RTW89_DBG_SEL_BB:
+		seq_puts(m, "Debug selected BB register\n");
+		start = 0x100;
+		end = 0x17f;
+		break;
+	case RTW89_DBG_SEL_IQK:
+		seq_puts(m, "Debug selected IQK register\n");
+		start = 0x180;
+		end = 0x1bf;
+		break;
+	case RTW89_DBG_SEL_RFC:
+		seq_puts(m, "Debug selected RFC register\n");
+		start = 0x1c0;
+		end = 0x1ff;
+		break;
+	default:
+		seq_puts(m, "Selected invalid register page\n");
+		return -EINVAL;
+	}
+
+	for (i = start; i <= end; i++) {
+		page = i << 8;
+		for (j = page; j < page + RTW89_MAC_PAGE_SIZE; j += 16) {
+			seq_printf(m, "%08xh : ", 0x18600000 + j);
+			for (k = 0; k < 4; k++) {
+				val = rtw89_read32(rtwdev, j + (k << 2));
+				seq_printf(m, "%08x ", val);
+			}
+			seq_puts(m, "\n");
+		}
+	}
+
+	return 0;
+}
+
+static ssize_t
+rtw89_debug_priv_mac_mem_dump_select(struct file *filp,
+				     const char __user *user_buf,
+				     size_t count, loff_t *loff)
+{
+	struct seq_file *m = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	u32 sel, start_addr, len;
+	int num;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	num = sscanf(buf, "%x %x %x", &sel, &start_addr, &len);
+	if (num != 3) {
+		rtw89_info(rtwdev, "invalid format: <sel> <start> <len>\n");
+		return -EINVAL;
+	}
+
+	debugfs_priv->mac_mem.sel = sel;
+	debugfs_priv->mac_mem.start = start_addr;
+	debugfs_priv->mac_mem.len = len;
+
+	rtw89_info(rtwdev, "select mem %d start %d len %d\n",
+		   sel, start_addr, len);
+
+	return count;
+}
+
+static const u32 mac_mem_base_addr_table[RTW89_MAC_MEM_MAX] = {
+	[RTW89_MAC_MEM_SHARED_BUF]	= SHARED_BUF_BASE_ADDR,
+	[RTW89_MAC_MEM_DMAC_TBL]	= DMAC_TBL_BASE_ADDR,
+	[RTW89_MAC_MEM_SHCUT_MACHDR]	= SHCUT_MACHDR_BASE_ADDR,
+	[RTW89_MAC_MEM_STA_SCHED]	= STA_SCHED_BASE_ADDR,
+	[RTW89_MAC_MEM_RXPLD_FLTR_CAM]	= RXPLD_FLTR_CAM_BASE_ADDR,
+	[RTW89_MAC_MEM_SECURITY_CAM]	= SECURITY_CAM_BASE_ADDR,
+	[RTW89_MAC_MEM_WOW_CAM]		= WOW_CAM_BASE_ADDR,
+	[RTW89_MAC_MEM_CMAC_TBL]	= CMAC_TBL_BASE_ADDR,
+	[RTW89_MAC_MEM_ADDR_CAM]	= ADDR_CAM_BASE_ADDR,
+	[RTW89_MAC_MEM_BA_CAM]		= BA_CAM_BASE_ADDR,
+	[RTW89_MAC_MEM_BCN_IE_CAM0]	= BCN_IE_CAM0_BASE_ADDR,
+	[RTW89_MAC_MEM_BCN_IE_CAM1]	= BCN_IE_CAM1_BASE_ADDR,
+};
+
+static void rtw89_debug_dump_mac_mem(struct seq_file *m,
+				     struct rtw89_dev *rtwdev,
+				     u8 sel, u32 start_addr, u32 len)
+{
+	u32 base_addr, start_page, residue;
+	u32 i, j, p, pages;
+	u32 dump_len, remain;
+	u32 val;
+
+	remain = len;
+	pages = len / MAC_MEM_DUMP_PAGE_SIZE + 1;
+	start_page = start_addr / MAC_MEM_DUMP_PAGE_SIZE;
+	residue = start_addr % MAC_MEM_DUMP_PAGE_SIZE;
+	base_addr = mac_mem_base_addr_table[sel];
+	base_addr += start_page * MAC_MEM_DUMP_PAGE_SIZE;
+
+	for (p = 0; p < pages; p++) {
+		dump_len = min_t(u32, remain, MAC_MEM_DUMP_PAGE_SIZE);
+		rtw89_write32(rtwdev, R_AX_FILTER_MODEL_ADDR, base_addr);
+		for (i = R_AX_INDIR_ACCESS_ENTRY + residue;
+		     i < R_AX_INDIR_ACCESS_ENTRY + dump_len;) {
+			seq_printf(m, "%08xh:", i);
+			for (j = 0;
+			     j < 4 && i < R_AX_INDIR_ACCESS_ENTRY + dump_len;
+			     j++, i += 4) {
+				val = rtw89_read32(rtwdev, i);
+				seq_printf(m, "  %08x", val);
+				remain -= 4;
+			}
+			seq_puts(m, "\n");
+		}
+		base_addr += MAC_MEM_DUMP_PAGE_SIZE;
+	}
+}
+
+static int
+rtw89_debug_priv_mac_mem_dump_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	rtw89_debug_dump_mac_mem(m, rtwdev,
+				 debugfs_priv->mac_mem.sel,
+				 debugfs_priv->mac_mem.start,
+				 debugfs_priv->mac_mem.len);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static ssize_t
+rtw89_debug_priv_mac_dbg_port_dump_select(struct file *filp,
+					  const char __user *user_buf,
+					  size_t count, loff_t *loff)
+{
+	struct seq_file *m = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	char buf[32];
+	size_t buf_size;
+	int sel, set;
+	int num;
+	bool enable;
+
+	buf_size = min(count, sizeof(buf) - 1);
+	if (copy_from_user(buf, user_buf, buf_size))
+		return -EFAULT;
+
+	buf[buf_size] = '\0';
+	num = sscanf(buf, "%d %d", &sel, &set);
+	if (num != 2) {
+		rtw89_info(rtwdev, "invalid format: <sel> <set>\n");
+		return -EINVAL;
+	}
+
+	enable = set == 0 ? false : true;
+	switch (sel) {
+	case 0:
+		debugfs_priv->dbgpkg_en.ss_dbg = enable;
+		break;
+	case 1:
+		debugfs_priv->dbgpkg_en.dle_dbg = enable;
+		break;
+	case 2:
+		debugfs_priv->dbgpkg_en.dmac_dbg = enable;
+		break;
+	case 3:
+		debugfs_priv->dbgpkg_en.cmac_dbg = enable;
+		break;
+	case 4:
+		debugfs_priv->dbgpkg_en.dbg_port = enable;
+		break;
+	default:
+		rtw89_info(rtwdev, "invalid args: sel %d set %d\n", sel, set);
+		return -EINVAL;
+	}
+
+	rtw89_info(rtwdev, "%s debug port dump %d\n",
+		   enable ? "Enable" : "Disable", sel);
+
+	return count;
+}
+
+static int rtw89_debug_mac_dump_ss_dbg(struct rtw89_dev *rtwdev,
+				       struct seq_file *m)
+{
+	return 0;
+}
+
+static int rtw89_debug_mac_dump_dle_dbg(struct rtw89_dev *rtwdev,
+					struct seq_file *m)
+{
+#define DLE_DFI_DUMP(__type, __target, __sel)				\
+({									\
+	u32 __ctrl;							\
+	u32 __reg_ctrl = R_AX_##__type##_DBG_FUN_INTF_CTL;		\
+	u32 __reg_data = R_AX_##__type##_DBG_FUN_INTF_DATA;		\
+	u32 __data, __val32;						\
+	int __ret;							\
+									\
+	__ctrl = FIELD_PREP(B_AX_##__type##_DFI_TRGSEL_MASK,		\
+			    DLE_DFI_TYPE_##__target) |			\
+		 FIELD_PREP(B_AX_##__type##_DFI_ADDR_MASK, __sel) |	\
+		 B_AX_WDE_DFI_ACTIVE;					\
+	rtw89_write32(rtwdev, __reg_ctrl, __ctrl);			\
+	__ret = read_poll_timeout(rtw89_read32, __val32,		\
+			!(__val32 & B_AX_##__type##_DFI_ACTIVE),	\
+			1000, 50000, false,				\
+			rtwdev, __reg_ctrl);				\
+	if (__ret) {							\
+		rtw89_err(rtwdev, "failed to dump DLE %s %s %d\n",	\
+			  #__type, #__target, __sel);			\
+		return __ret;						\
+	}								\
+									\
+	__data = rtw89_read32(rtwdev, __reg_data);			\
+	__data;								\
+})
+
+#define DLE_DFI_FREE_PAGE_DUMP(__m, __type)				\
+({									\
+	u32 __freepg, __pubpg;						\
+	u32 __freepg_head, __freepg_tail, __pubpg_num;			\
+									\
+	__freepg = DLE_DFI_DUMP(__type, FREEPG, 0);			\
+	__pubpg = DLE_DFI_DUMP(__type, FREEPG, 1);			\
+	__freepg_head = FIELD_GET(B_AX_DLE_FREE_HEADPG, __freepg);	\
+	__freepg_tail = FIELD_GET(B_AX_DLE_FREE_TAILPG, __freepg);	\
+	__pubpg_num = FIELD_GET(B_AX_DLE_PUB_PGNUM, __pubpg);		\
+	seq_printf(__m, "[%s] freepg head: %d\n",			\
+		   #__type, __freepg_head);				\
+	seq_printf(__m, "[%s] freepg tail: %d\n",			\
+		   #__type, __freepg_tail);				\
+	seq_printf(__m, "[%s] pubpg num  : %d\n",			\
+		  #__type, __pubpg_num);				\
+})
+
+#define case_QUOTA(__m, __type, __id)					\
+	case __type##_QTAID_##__id:					\
+		val32 = DLE_DFI_DUMP(__type, QUOTA, __type##_QTAID_##__id);	\
+		rsv_pgnum = FIELD_GET(B_AX_DLE_RSV_PGNUM, val32);	\
+		use_pgnum = FIELD_GET(B_AX_DLE_USE_PGNUM, val32);	\
+		seq_printf(__m, "[%s][%s] rsv_pgnum: %d\n",		\
+			   #__type, #__id, rsv_pgnum);			\
+		seq_printf(__m, "[%s][%s] use_pgnum: %d\n",		\
+			   #__type, #__id, use_pgnum);			\
+		break
+	u32 quota_id;
+	u32 val32;
+	u16 rsv_pgnum, use_pgnum;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, 0, RTW89_DMAC_SEL);
+	if (ret) {
+		seq_puts(m, "[DLE]  : DMAC not enabled\n");
+		return ret;
+	}
+
+	DLE_DFI_FREE_PAGE_DUMP(m, WDE);
+	DLE_DFI_FREE_PAGE_DUMP(m, PLE);
+	for (quota_id = 0; quota_id <= WDE_QTAID_CPUIO; quota_id++) {
+		switch (quota_id) {
+		case_QUOTA(m, WDE, HOST_IF);
+		case_QUOTA(m, WDE, WLAN_CPU);
+		case_QUOTA(m, WDE, DATA_CPU);
+		case_QUOTA(m, WDE, PKTIN);
+		case_QUOTA(m, WDE, CPUIO);
+		}
+	}
+	for (quota_id = 0; quota_id <= PLE_QTAID_CPUIO; quota_id++) {
+		switch (quota_id) {
+		case_QUOTA(m, PLE, B0_TXPL);
+		case_QUOTA(m, PLE, B1_TXPL);
+		case_QUOTA(m, PLE, C2H);
+		case_QUOTA(m, PLE, H2C);
+		case_QUOTA(m, PLE, WLAN_CPU);
+		case_QUOTA(m, PLE, MPDU);
+		case_QUOTA(m, PLE, CMAC0_RX);
+		case_QUOTA(m, PLE, CMAC1_RX);
+		case_QUOTA(m, PLE, CMAC1_BBRPT);
+		case_QUOTA(m, PLE, WDRLS);
+		case_QUOTA(m, PLE, CPUIO);
+		}
+	}
+
+	return 0;
+
+#undef case_QUOTA
+#undef DLE_DFI_DUMP
+#undef DLE_DFI_FREE_PAGE_DUMP
+}
+
+static int rtw89_debug_mac_dump_dmac_dbg(struct rtw89_dev *rtwdev,
+					 struct seq_file *m)
+{
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, 0, RTW89_DMAC_SEL);
+	if (ret) {
+		seq_puts(m, "[DMAC] : DMAC not enabled\n");
+		return ret;
+	}
+
+	seq_printf(m, "R_AX_DMAC_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_DMAC_ERR_ISR));
+	seq_printf(m, "[0]R_AX_WDRLS_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_WDRLS_ERR_ISR));
+	seq_printf(m, "[1]R_AX_SEC_ERR_IMR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_SEC_ERR_IMR_ISR));
+	seq_printf(m, "[2.1]R_AX_MPDU_TX_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_MPDU_TX_ERR_ISR));
+	seq_printf(m, "[2.2]R_AX_MPDU_RX_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_MPDU_RX_ERR_ISR));
+	seq_printf(m, "[3]R_AX_STA_SCHEDULER_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_STA_SCHEDULER_ERR_ISR));
+	seq_printf(m, "[4]R_AX_WDE_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_WDE_ERR_ISR));
+	seq_printf(m, "[5.1]R_AX_TXPKTCTL_ERR_IMR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR));
+	seq_printf(m, "[5.2]R_AX_TXPKTCTL_ERR_IMR_ISR_B1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR_B1));
+	seq_printf(m, "[6]R_AX_PLE_ERR_FLAG_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_PLE_ERR_FLAG_ISR));
+	seq_printf(m, "[7]R_AX_PKTIN_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_PKTIN_ERR_ISR));
+	seq_printf(m, "[8.1]R_AX_OTHER_DISPATCHER_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_OTHER_DISPATCHER_ERR_ISR));
+	seq_printf(m, "[8.2]R_AX_HOST_DISPATCHER_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_HOST_DISPATCHER_ERR_ISR));
+	seq_printf(m, "[8.3]R_AX_CPU_DISPATCHER_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_CPU_DISPATCHER_ERR_ISR));
+	seq_printf(m, "[10]R_AX_CPUIO_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_CPUIO_ERR_ISR));
+	seq_printf(m, "[11.1]R_AX_BBRPT_COM_ERR_IMR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_BBRPT_COM_ERR_IMR_ISR));
+	seq_printf(m, "[11.2]R_AX_BBRPT_CHINFO_ERR_IMR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_BBRPT_CHINFO_ERR_IMR_ISR));
+	seq_printf(m, "[11.3]R_AX_BBRPT_DFS_ERR_IMR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_BBRPT_DFS_ERR_IMR_ISR));
+	seq_printf(m, "[11.4]R_AX_LA_ERRFLAG=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_LA_ERRFLAG));
+
+	return 0;
+}
+
+static int rtw89_debug_mac_dump_cmac_dbg(struct rtw89_dev *rtwdev,
+					 struct seq_file *m)
+{
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, 0, RTW89_CMAC_SEL);
+	if (ret) {
+		seq_puts(m, "[CMAC] : CMAC 0 not enabled\n");
+		return ret;
+	}
+
+	seq_printf(m, "R_AX_CMAC_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_CMAC_ERR_ISR));
+	seq_printf(m, "[0]R_AX_SCHEDULE_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_SCHEDULE_ERR_ISR));
+	seq_printf(m, "[1]R_AX_PTCL_ISR0=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_PTCL_ISR0));
+	seq_printf(m, "[3]R_AX_DLE_CTRL=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_DLE_CTRL));
+	seq_printf(m, "[4]R_AX_PHYINFO_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_PHYINFO_ERR_ISR));
+	seq_printf(m, "[5]R_AX_TXPWR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_TXPWR_ISR));
+	seq_printf(m, "[6]R_AX_RMAC_ERR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_RMAC_ERR_ISR));
+	seq_printf(m, "[7]R_AX_TMAC_ERR_IMR_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_TMAC_ERR_IMR_ISR));
+
+	ret = rtw89_mac_check_mac_en(rtwdev, 1, RTW89_CMAC_SEL);
+	if (ret) {
+		seq_puts(m, "[CMAC] : CMAC 1 not enabled\n");
+		return ret;
+	}
+
+	seq_printf(m, "R_AX_CMAC_ERR_ISR_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_CMAC_ERR_ISR_C1));
+	seq_printf(m, "[0]R_AX_SCHEDULE_ERR_ISR_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_SCHEDULE_ERR_ISR_C1));
+	seq_printf(m, "[1]R_AX_PTCL_ISR0_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_PTCL_ISR0_C1));
+	seq_printf(m, "[3]R_AX_DLE_CTRL_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_DLE_CTRL_C1));
+	seq_printf(m, "[4]R_AX_PHYINFO_ERR_ISR_C1=0x%02x\n",
+		   rtw89_read32(rtwdev, R_AX_PHYINFO_ERR_ISR_C1));
+	seq_printf(m, "[5]R_AX_TXPWR_ISR_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_TXPWR_ISR_C1));
+	seq_printf(m, "[6]R_AX_RMAC_ERR_ISR_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_RMAC_ERR_ISR_C1));
+	seq_printf(m, "[7]R_AX_TMAC_ERR_IMR_ISR_C1=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_TMAC_ERR_IMR_ISR_C1));
+
+	return 0;
+}
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ptcl_c0 = {
+	.sel_addr = R_AX_PTCL_DBG,
+	.sel_byte = 1,
+	.sel_msk = B_AX_PTCL_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x3F,
+	.rd_addr = R_AX_PTCL_DBG_INFO,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PTCL_DBG_INFO_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ptcl_c1 = {
+	.sel_addr = R_AX_PTCL_DBG_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_PTCL_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x3F,
+	.rd_addr = R_AX_PTCL_DBG_INFO_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PTCL_DBG_INFO_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_sch_c0 = {
+	.sel_addr = R_AX_SCH_DBG_SEL,
+	.sel_byte = 1,
+	.sel_msk = B_AX_SCH_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x2F,
+	.rd_addr = R_AX_SCH_DBG,
+	.rd_byte = 4,
+	.rd_msk = B_AX_SCHEDULER_DBG_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_sch_c1 = {
+	.sel_addr = R_AX_SCH_DBG_SEL_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_SCH_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x2F,
+	.rd_addr = R_AX_SCH_DBG_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_SCHEDULER_DBG_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_tmac_c0 = {
+	.sel_addr = R_AX_MACTX_DBG_SEL_CNT,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DBGSEL_MACTX_MASK,
+	.srt = 0x00,
+	.end = 0x19,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_tmac_c1 = {
+	.sel_addr = R_AX_MACTX_DBG_SEL_CNT_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DBGSEL_MACTX_MASK,
+	.srt = 0x00,
+	.end = 0x19,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_rmac_c0 = {
+	.sel_addr = R_AX_RX_DEBUG_SELECT,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DEBUG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x58,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_rmac_c1 = {
+	.sel_addr = R_AX_RX_DEBUG_SELECT_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DEBUG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x58,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_rmacst_c0 = {
+	.sel_addr = R_AX_RX_STATE_MONITOR,
+	.sel_byte = 1,
+	.sel_msk = B_AX_STATE_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x17,
+	.rd_addr = R_AX_RX_STATE_MONITOR,
+	.rd_byte = 4,
+	.rd_msk = B_AX_RX_STATE_MONITOR_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_rmacst_c1 = {
+	.sel_addr = R_AX_RX_STATE_MONITOR_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_STATE_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x17,
+	.rd_addr = R_AX_RX_STATE_MONITOR_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_RX_STATE_MONITOR_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_rmac_plcp_c0 = {
+	.sel_addr = R_AX_RMAC_PLCP_MON,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PCLP_MON_SEL_MASK,
+	.srt = 0x0,
+	.end = 0xF,
+	.rd_addr = R_AX_RMAC_PLCP_MON,
+	.rd_byte = 4,
+	.rd_msk = B_AX_RMAC_PLCP_MON_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_rmac_plcp_c1 = {
+	.sel_addr = R_AX_RMAC_PLCP_MON_C1,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PCLP_MON_SEL_MASK,
+	.srt = 0x0,
+	.end = 0xF,
+	.rd_addr = R_AX_RMAC_PLCP_MON_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_RMAC_PLCP_MON_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_trxptcl_c0 = {
+	.sel_addr = R_AX_DBGSEL_TRXPTCL,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DBGSEL_TRXPTCL_MASK,
+	.srt = 0x08,
+	.end = 0x10,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_trxptcl_c1 = {
+	.sel_addr = R_AX_DBGSEL_TRXPTCL_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DBGSEL_TRXPTCL_MASK,
+	.srt = 0x08,
+	.end = 0x10,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_tx_infol_c0 = {
+	.sel_addr = R_AX_WMAC_TX_CTRL_DEBUG,
+	.sel_byte = 1,
+	.sel_msk = B_AX_TX_CTRL_DEBUG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x07,
+	.rd_addr = R_AX_WMAC_TX_INFO0_DEBUG,
+	.rd_byte = 4,
+	.rd_msk = B_AX_TX_CTRL_INFO_P0_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_tx_infoh_c0 = {
+	.sel_addr = R_AX_WMAC_TX_CTRL_DEBUG,
+	.sel_byte = 1,
+	.sel_msk = B_AX_TX_CTRL_DEBUG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x07,
+	.rd_addr = R_AX_WMAC_TX_INFO1_DEBUG,
+	.rd_byte = 4,
+	.rd_msk = B_AX_TX_CTRL_INFO_P1_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_tx_infol_c1 = {
+	.sel_addr = R_AX_WMAC_TX_CTRL_DEBUG_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_TX_CTRL_DEBUG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x07,
+	.rd_addr = R_AX_WMAC_TX_INFO0_DEBUG_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_TX_CTRL_INFO_P0_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_tx_infoh_c1 = {
+	.sel_addr = R_AX_WMAC_TX_CTRL_DEBUG_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_TX_CTRL_DEBUG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x07,
+	.rd_addr = R_AX_WMAC_TX_INFO1_DEBUG_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_TX_CTRL_INFO_P1_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_txtf_infol_c0 = {
+	.sel_addr = R_AX_WMAC_TX_TF_INFO_0,
+	.sel_byte = 1,
+	.sel_msk = B_AX_WMAC_TX_TF_INFO_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x04,
+	.rd_addr = R_AX_WMAC_TX_TF_INFO_1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WMAC_TX_TF_INFO_P0_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_txtf_infoh_c0 = {
+	.sel_addr = R_AX_WMAC_TX_TF_INFO_0,
+	.sel_byte = 1,
+	.sel_msk = B_AX_WMAC_TX_TF_INFO_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x04,
+	.rd_addr = R_AX_WMAC_TX_TF_INFO_2,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WMAC_TX_TF_INFO_P1_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_txtf_infol_c1 = {
+	.sel_addr = R_AX_WMAC_TX_TF_INFO_0_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_WMAC_TX_TF_INFO_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x04,
+	.rd_addr = R_AX_WMAC_TX_TF_INFO_1_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WMAC_TX_TF_INFO_P0_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_txtf_infoh_c1 = {
+	.sel_addr = R_AX_WMAC_TX_TF_INFO_0_C1,
+	.sel_byte = 1,
+	.sel_msk = B_AX_WMAC_TX_TF_INFO_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x04,
+	.rd_addr = R_AX_WMAC_TX_TF_INFO_2_C1,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WMAC_TX_TF_INFO_P1_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_bufmgn_freepg = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80000000,
+	.end = 0x80000001,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_bufmgn_quota = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80010000,
+	.end = 0x80010004,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_bufmgn_pagellt = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80020000,
+	.end = 0x80020FFF,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_bufmgn_pktinfo = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80030000,
+	.end = 0x80030FFF,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_quemgn_prepkt = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80040000,
+	.end = 0x80040FFF,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_quemgn_nxtpkt = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80050000,
+	.end = 0x80050FFF,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_quemgn_qlnktbl = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80060000,
+	.end = 0x80060453,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_wde_quemgn_qempty = {
+	.sel_addr = R_AX_WDE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_WDE_DFI_DATA_MASK,
+	.srt = 0x80070000,
+	.end = 0x80070011,
+	.rd_addr = R_AX_WDE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_WDE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_bufmgn_freepg = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80000000,
+	.end = 0x80000001,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_bufmgn_quota = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80010000,
+	.end = 0x8001000A,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_bufmgn_pagellt = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80020000,
+	.end = 0x80020DBF,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_bufmgn_pktinfo = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80030000,
+	.end = 0x80030DBF,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_quemgn_prepkt = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80040000,
+	.end = 0x80040DBF,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_quemgn_nxtpkt = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80050000,
+	.end = 0x80050DBF,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_quemgn_qlnktbl = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80060000,
+	.end = 0x80060041,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_ple_quemgn_qempty = {
+	.sel_addr = R_AX_PLE_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_PLE_DFI_DATA_MASK,
+	.srt = 0x80070000,
+	.end = 0x80070001,
+	.rd_addr = R_AX_PLE_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_PLE_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pktinfo = {
+	.sel_addr = R_AX_DBG_FUN_INTF_CTL,
+	.sel_byte = 4,
+	.sel_msk = B_AX_DFI_DATA_MASK,
+	.srt = 0x80000000,
+	.end = 0x8000017f,
+	.rd_addr = R_AX_DBG_FUN_INTF_DATA,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DFI_DATA_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_txdma = {
+	.sel_addr = R_AX_PCIE_DBG_CTRL,
+	.sel_byte = 2,
+	.sel_msk = B_AX_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x03,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_rxdma = {
+	.sel_addr = R_AX_PCIE_DBG_CTRL,
+	.sel_byte = 2,
+	.sel_msk = B_AX_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x04,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_cvt = {
+	.sel_addr = R_AX_PCIE_DBG_CTRL,
+	.sel_byte = 2,
+	.sel_msk = B_AX_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x01,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_cxpl = {
+	.sel_addr = R_AX_PCIE_DBG_CTRL,
+	.sel_byte = 2,
+	.sel_msk = B_AX_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x05,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_io = {
+	.sel_addr = R_AX_PCIE_DBG_CTRL,
+	.sel_byte = 2,
+	.sel_msk = B_AX_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x05,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_misc = {
+	.sel_addr = R_AX_PCIE_DBG_CTRL,
+	.sel_byte = 2,
+	.sel_msk = B_AX_DBG_SEL_MASK,
+	.srt = 0x00,
+	.end = 0x06,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info dbg_port_pcie_misc2 = {
+	.sel_addr = R_AX_DBG_CTRL,
+	.sel_byte = 1,
+	.sel_msk = B_AX_DBG_SEL0,
+	.srt = 0x34,
+	.end = 0x3C,
+	.rd_addr = R_AX_DBG_PORT_SEL,
+	.rd_byte = 4,
+	.rd_msk = B_AX_DEBUG_ST_MASK
+};
+
+static const struct rtw89_mac_dbg_port_info *
+rtw89_debug_mac_dbg_port_sel(struct seq_file *m,
+			     struct rtw89_dev *rtwdev, u32 sel)
+{
+	const struct rtw89_mac_dbg_port_info *info;
+	u32 val32;
+	u16 val16;
+	u8 val8;
+
+	switch (sel) {
+	case RTW89_DBG_PORT_SEL_PTCL_C0:
+		info = &dbg_port_ptcl_c0;
+		val16 = rtw89_read16(rtwdev, R_AX_PTCL_DBG);
+		val16 |= B_AX_PTCL_DBG_EN;
+		rtw89_write16(rtwdev, R_AX_PTCL_DBG, val16);
+		seq_puts(m, "Enable PTCL C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PTCL_C1:
+		info = &dbg_port_ptcl_c1;
+		val16 = rtw89_read16(rtwdev, R_AX_PTCL_DBG_C1);
+		val16 |= B_AX_PTCL_DBG_EN;
+		rtw89_write16(rtwdev, R_AX_PTCL_DBG_C1, val16);
+		seq_puts(m, "Enable PTCL C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_SCH_C0:
+		info = &dbg_port_sch_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_SCH_DBG_SEL);
+		val32 |= B_AX_SCH_DBG_EN;
+		rtw89_write32(rtwdev, R_AX_SCH_DBG_SEL, val32);
+		seq_puts(m, "Enable SCH C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_SCH_C1:
+		info = &dbg_port_sch_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_SCH_DBG_SEL_C1);
+		val32 |= B_AX_SCH_DBG_EN;
+		rtw89_write32(rtwdev, R_AX_SCH_DBG_SEL_C1, val32);
+		seq_puts(m, "Enable SCH C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TMAC_C0:
+		info = &dbg_port_tmac_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_DBGSEL_TRXPTCL);
+		val32 = u32_replace_bits(val32, TRXPTRL_DBG_SEL_TMAC,
+					 B_AX_DBGSEL_TRXPTCL_MASK);
+		rtw89_write32(rtwdev, R_AX_DBGSEL_TRXPTCL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, TMAC_DBG_SEL_C0, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, TMAC_DBG_SEL_C0, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_SYS_STATUS1);
+		val32 = u32_replace_bits(val32, MAC_DBG_SEL, B_AX_SEL_0XC0_MASK);
+		rtw89_write32(rtwdev, R_AX_SYS_STATUS1, val32);
+		seq_puts(m, "Enable TMAC C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TMAC_C1:
+		info = &dbg_port_tmac_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_DBGSEL_TRXPTCL_C1);
+		val32 = u32_replace_bits(val32, TRXPTRL_DBG_SEL_TMAC,
+					 B_AX_DBGSEL_TRXPTCL_MASK);
+		rtw89_write32(rtwdev, R_AX_DBGSEL_TRXPTCL_C1, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, TMAC_DBG_SEL_C1, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, TMAC_DBG_SEL_C1, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_SYS_STATUS1);
+		val32 = u32_replace_bits(val32, MAC_DBG_SEL, B_AX_SEL_0XC0_MASK);
+		rtw89_write32(rtwdev, R_AX_SYS_STATUS1, val32);
+		seq_puts(m, "Enable TMAC C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_RMAC_C0:
+		info = &dbg_port_rmac_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_DBGSEL_TRXPTCL);
+		val32 = u32_replace_bits(val32, TRXPTRL_DBG_SEL_RMAC,
+					 B_AX_DBGSEL_TRXPTCL_MASK);
+		rtw89_write32(rtwdev, R_AX_DBGSEL_TRXPTCL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, RMAC_DBG_SEL_C0, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, RMAC_DBG_SEL_C0, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_SYS_STATUS1);
+		val32 = u32_replace_bits(val32, MAC_DBG_SEL, B_AX_SEL_0XC0_MASK);
+		rtw89_write32(rtwdev, R_AX_SYS_STATUS1, val32);
+
+		val8 = rtw89_read8(rtwdev, R_AX_DBGSEL_TRXPTCL);
+		val8 = u8_replace_bits(val8, RMAC_CMAC_DBG_SEL,
+				       B_AX_DBGSEL_TRXPTCL_MASK);
+		rtw89_write8(rtwdev, R_AX_DBGSEL_TRXPTCL, val8);
+		seq_puts(m, "Enable RMAC C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_RMAC_C1:
+		info = &dbg_port_rmac_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_DBGSEL_TRXPTCL_C1);
+		val32 = u32_replace_bits(val32, TRXPTRL_DBG_SEL_RMAC,
+					 B_AX_DBGSEL_TRXPTCL_MASK);
+		rtw89_write32(rtwdev, R_AX_DBGSEL_TRXPTCL_C1, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, RMAC_DBG_SEL_C1, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, RMAC_DBG_SEL_C1, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_SYS_STATUS1);
+		val32 = u32_replace_bits(val32, MAC_DBG_SEL, B_AX_SEL_0XC0_MASK);
+		rtw89_write32(rtwdev, R_AX_SYS_STATUS1, val32);
+
+		val8 = rtw89_read8(rtwdev, R_AX_DBGSEL_TRXPTCL_C1);
+		val8 = u8_replace_bits(val8, RMAC_CMAC_DBG_SEL,
+				       B_AX_DBGSEL_TRXPTCL_MASK);
+		rtw89_write8(rtwdev, R_AX_DBGSEL_TRXPTCL_C1, val8);
+		seq_puts(m, "Enable RMAC C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_RMACST_C0:
+		info = &dbg_port_rmacst_c0;
+		seq_puts(m, "Enable RMAC state C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_RMACST_C1:
+		info = &dbg_port_rmacst_c1;
+		seq_puts(m, "Enable RMAC state C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_RMAC_PLCP_C0:
+		info = &dbg_port_rmac_plcp_c0;
+		seq_puts(m, "Enable RMAC PLCP C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_RMAC_PLCP_C1:
+		info = &dbg_port_rmac_plcp_c1;
+		seq_puts(m, "Enable RMAC PLCP C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TRXPTCL_C0:
+		info = &dbg_port_trxptcl_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, TRXPTCL_DBG_SEL_C0, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, TRXPTCL_DBG_SEL_C0, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_SYS_STATUS1);
+		val32 = u32_replace_bits(val32, MAC_DBG_SEL, B_AX_SEL_0XC0_MASK);
+		rtw89_write32(rtwdev, R_AX_SYS_STATUS1, val32);
+		seq_puts(m, "Enable TRXPTCL C0 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TRXPTCL_C1:
+		info = &dbg_port_trxptcl_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, TRXPTCL_DBG_SEL_C1, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, TRXPTCL_DBG_SEL_C1, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+
+		val32 = rtw89_read32(rtwdev, R_AX_SYS_STATUS1);
+		val32 = u32_replace_bits(val32, MAC_DBG_SEL, B_AX_SEL_0XC0_MASK);
+		rtw89_write32(rtwdev, R_AX_SYS_STATUS1, val32);
+		seq_puts(m, "Enable TRXPTCL C1 dbgport.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TX_INFOL_C0:
+		info = &dbg_port_tx_infol_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1, val32);
+		seq_puts(m, "Enable tx infol dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TX_INFOH_C0:
+		info = &dbg_port_tx_infoh_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1, val32);
+		seq_puts(m, "Enable tx infoh dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TX_INFOL_C1:
+		info = &dbg_port_tx_infol_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1_C1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1_C1, val32);
+		seq_puts(m, "Enable tx infol dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TX_INFOH_C1:
+		info = &dbg_port_tx_infoh_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1_C1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1_C1, val32);
+		seq_puts(m, "Enable tx infoh dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TXTF_INFOL_C0:
+		info = &dbg_port_txtf_infol_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1, val32);
+		seq_puts(m, "Enable tx tf infol dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TXTF_INFOH_C0:
+		info = &dbg_port_txtf_infoh_c0;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1, val32);
+		seq_puts(m, "Enable tx tf infoh dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TXTF_INFOL_C1:
+		info = &dbg_port_txtf_infol_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1_C1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1_C1, val32);
+		seq_puts(m, "Enable tx tf infol dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_TXTF_INFOH_C1:
+		info = &dbg_port_txtf_infoh_c1;
+		val32 = rtw89_read32(rtwdev, R_AX_TCR1_C1);
+		val32 |= B_AX_TCR_FORCE_READ_TXDFIFO;
+		rtw89_write32(rtwdev, R_AX_TCR1_C1, val32);
+		seq_puts(m, "Enable tx tf infoh dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_BUFMGN_FREEPG:
+		info = &dbg_port_wde_bufmgn_freepg;
+		seq_puts(m, "Enable wde bufmgn freepg dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_BUFMGN_QUOTA:
+		info = &dbg_port_wde_bufmgn_quota;
+		seq_puts(m, "Enable wde bufmgn quota dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_BUFMGN_PAGELLT:
+		info = &dbg_port_wde_bufmgn_pagellt;
+		seq_puts(m, "Enable wde bufmgn pagellt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_BUFMGN_PKTINFO:
+		info = &dbg_port_wde_bufmgn_pktinfo;
+		seq_puts(m, "Enable wde bufmgn pktinfo dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_QUEMGN_PREPKT:
+		info = &dbg_port_wde_quemgn_prepkt;
+		seq_puts(m, "Enable wde quemgn prepkt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_QUEMGN_NXTPKT:
+		info = &dbg_port_wde_quemgn_nxtpkt;
+		seq_puts(m, "Enable wde quemgn nxtpkt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_QUEMGN_QLNKTBL:
+		info = &dbg_port_wde_quemgn_qlnktbl;
+		seq_puts(m, "Enable wde quemgn qlnktbl dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_WDE_QUEMGN_QEMPTY:
+		info = &dbg_port_wde_quemgn_qempty;
+		seq_puts(m, "Enable wde quemgn qempty dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_BUFMGN_FREEPG:
+		info = &dbg_port_ple_bufmgn_freepg;
+		seq_puts(m, "Enable ple bufmgn freepg dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_BUFMGN_QUOTA:
+		info = &dbg_port_ple_bufmgn_quota;
+		seq_puts(m, "Enable ple bufmgn quota dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_BUFMGN_PAGELLT:
+		info = &dbg_port_ple_bufmgn_pagellt;
+		seq_puts(m, "Enable ple bufmgn pagellt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_BUFMGN_PKTINFO:
+		info = &dbg_port_ple_bufmgn_pktinfo;
+		seq_puts(m, "Enable ple bufmgn pktinfo dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_QUEMGN_PREPKT:
+		info = &dbg_port_ple_quemgn_prepkt;
+		seq_puts(m, "Enable ple quemgn prepkt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_QUEMGN_NXTPKT:
+		info = &dbg_port_ple_quemgn_nxtpkt;
+		seq_puts(m, "Enable ple quemgn nxtpkt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_QUEMGN_QLNKTBL:
+		info = &dbg_port_ple_quemgn_qlnktbl;
+		seq_puts(m, "Enable ple quemgn qlnktbl dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PLE_QUEMGN_QEMPTY:
+		info = &dbg_port_ple_quemgn_qempty;
+		seq_puts(m, "Enable ple quemgn qempty dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PKTINFO:
+		info = &dbg_port_pktinfo;
+		seq_puts(m, "Enable pktinfo dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_TXDMA:
+		info = &dbg_port_pcie_txdma;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, PCIE_TXDMA_DBG_SEL, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, PCIE_TXDMA_DBG_SEL, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+		seq_puts(m, "Enable pcie txdma dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_RXDMA:
+		info = &dbg_port_pcie_rxdma;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, PCIE_RXDMA_DBG_SEL, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, PCIE_RXDMA_DBG_SEL, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+		seq_puts(m, "Enable pcie rxdma dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_CVT:
+		info = &dbg_port_pcie_cvt;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, PCIE_CVT_DBG_SEL, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, PCIE_CVT_DBG_SEL, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+		seq_puts(m, "Enable pcie cvt dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_CXPL:
+		info = &dbg_port_pcie_cxpl;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, PCIE_CXPL_DBG_SEL, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, PCIE_CXPL_DBG_SEL, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+		seq_puts(m, "Enable pcie cxpl dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_IO:
+		info = &dbg_port_pcie_io;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, PCIE_IO_DBG_SEL, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, PCIE_IO_DBG_SEL, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+		seq_puts(m, "Enable pcie io dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_MISC:
+		info = &dbg_port_pcie_misc;
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_CTRL);
+		val32 = u32_replace_bits(val32, PCIE_MISC_DBG_SEL, B_AX_DBG_SEL0);
+		val32 = u32_replace_bits(val32, PCIE_MISC_DBG_SEL, B_AX_DBG_SEL1);
+		rtw89_write32(rtwdev, R_AX_DBG_CTRL, val32);
+		seq_puts(m, "Enable pcie misc dump.\n");
+		break;
+	case RTW89_DBG_PORT_SEL_PCIE_MISC2:
+		info = &dbg_port_pcie_misc2;
+		val16 = rtw89_read16(rtwdev, R_AX_PCIE_DBG_CTRL);
+		val16 = u16_replace_bits(val16, PCIE_MISC2_DBG_SEL,
+					 B_AX_DBG_SEL_MASK);
+		rtw89_write16(rtwdev, R_AX_PCIE_DBG_CTRL, val16);
+		seq_puts(m, "Enable pcie misc2 dump.\n");
+		break;
+	default:
+		seq_puts(m, "Dbg port select err\n");
+		return NULL;
+	}
+
+	return info;
+}
+
+static bool is_dbg_port_valid(struct rtw89_dev *rtwdev, u32 sel)
+{
+	if (rtwdev->hci.type != RTW89_HCI_TYPE_PCIE &&
+	    sel >= RTW89_DBG_PORT_SEL_PCIE_TXDMA &&
+	    sel <= RTW89_DBG_PORT_SEL_PCIE_MISC2)
+		return false;
+	if (rtwdev->chip->chip_id == RTL8852B &&
+	    sel >= RTW89_DBG_PORT_SEL_PTCL_C1 &&
+	    sel <= RTW89_DBG_PORT_SEL_TXTF_INFOH_C1)
+		return false;
+	if (rtw89_mac_check_mac_en(rtwdev, 0, RTW89_DMAC_SEL) &&
+	    sel >= RTW89_DBG_PORT_SEL_WDE_BUFMGN_FREEPG &&
+	    sel <= RTW89_DBG_PORT_SEL_PKTINFO)
+		return false;
+	if (rtw89_mac_check_mac_en(rtwdev, 0, RTW89_CMAC_SEL) &&
+	    sel >= RTW89_DBG_PORT_SEL_PTCL_C0 &&
+	    sel <= RTW89_DBG_PORT_SEL_TXTF_INFOH_C0)
+		return false;
+	if (rtw89_mac_check_mac_en(rtwdev, 1, RTW89_CMAC_SEL) &&
+	    sel >= RTW89_DBG_PORT_SEL_PTCL_C1 &&
+	    sel <= RTW89_DBG_PORT_SEL_TXTF_INFOH_C1)
+		return false;
+
+	return true;
+}
+
+static int rtw89_debug_mac_dbg_port_dump(struct rtw89_dev *rtwdev,
+					 struct seq_file *m, u32 sel)
+{
+	const struct rtw89_mac_dbg_port_info *info;
+	u8 val8;
+	u16 val16;
+	u32 val32;
+	u32 i;
+
+	info = rtw89_debug_mac_dbg_port_sel(m, rtwdev, sel);
+	if (!info) {
+		rtw89_err(rtwdev, "failed to select debug port %d\n", sel);
+		return -EINVAL;
+	}
+
+#define case_DBG_SEL(__sel) \
+	case RTW89_DBG_PORT_SEL_##__sel: \
+		seq_puts(m, "Dump debug port " #__sel ":\n"); \
+		break
+
+	switch (sel) {
+	case_DBG_SEL(PTCL_C0);
+	case_DBG_SEL(PTCL_C1);
+	case_DBG_SEL(SCH_C0);
+	case_DBG_SEL(SCH_C1);
+	case_DBG_SEL(TMAC_C0);
+	case_DBG_SEL(TMAC_C1);
+	case_DBG_SEL(RMAC_C0);
+	case_DBG_SEL(RMAC_C1);
+	case_DBG_SEL(RMACST_C0);
+	case_DBG_SEL(RMACST_C1);
+	case_DBG_SEL(TRXPTCL_C0);
+	case_DBG_SEL(TRXPTCL_C1);
+	case_DBG_SEL(TX_INFOL_C0);
+	case_DBG_SEL(TX_INFOH_C0);
+	case_DBG_SEL(TX_INFOL_C1);
+	case_DBG_SEL(TX_INFOH_C1);
+	case_DBG_SEL(TXTF_INFOL_C0);
+	case_DBG_SEL(TXTF_INFOH_C0);
+	case_DBG_SEL(TXTF_INFOL_C1);
+	case_DBG_SEL(TXTF_INFOH_C1);
+	case_DBG_SEL(WDE_BUFMGN_FREEPG);
+	case_DBG_SEL(WDE_BUFMGN_QUOTA);
+	case_DBG_SEL(WDE_BUFMGN_PAGELLT);
+	case_DBG_SEL(WDE_BUFMGN_PKTINFO);
+	case_DBG_SEL(WDE_QUEMGN_PREPKT);
+	case_DBG_SEL(WDE_QUEMGN_NXTPKT);
+	case_DBG_SEL(WDE_QUEMGN_QLNKTBL);
+	case_DBG_SEL(WDE_QUEMGN_QEMPTY);
+	case_DBG_SEL(PLE_BUFMGN_FREEPG);
+	case_DBG_SEL(PLE_BUFMGN_QUOTA);
+	case_DBG_SEL(PLE_BUFMGN_PAGELLT);
+	case_DBG_SEL(PLE_BUFMGN_PKTINFO);
+	case_DBG_SEL(PLE_QUEMGN_PREPKT);
+	case_DBG_SEL(PLE_QUEMGN_NXTPKT);
+	case_DBG_SEL(PLE_QUEMGN_QLNKTBL);
+	case_DBG_SEL(PLE_QUEMGN_QEMPTY);
+	case_DBG_SEL(PKTINFO);
+	case_DBG_SEL(PCIE_TXDMA);
+	case_DBG_SEL(PCIE_RXDMA);
+	case_DBG_SEL(PCIE_CVT);
+	case_DBG_SEL(PCIE_CXPL);
+	case_DBG_SEL(PCIE_IO);
+	case_DBG_SEL(PCIE_MISC);
+	case_DBG_SEL(PCIE_MISC2);
+	}
+
+#undef case_DBG_SEL
+
+	seq_printf(m, "Sel addr = 0x%X\n", info->sel_addr);
+	seq_printf(m, "Read addr = 0x%X\n", info->rd_addr);
+
+	for (i = info->srt; i <= info->end; i++) {
+		switch (info->sel_byte) {
+		case 1:
+		default:
+			rtw89_write8_mask(rtwdev, info->sel_addr,
+					  info->sel_msk, i);
+			seq_printf(m, "0x%02X: ", i);
+			break;
+		case 2:
+			rtw89_write16_mask(rtwdev, info->sel_addr,
+					   info->sel_msk, i);
+			seq_printf(m, "0x%04X: ", i);
+			break;
+		case 4:
+			rtw89_write32_mask(rtwdev, info->sel_addr,
+					   info->sel_msk, i);
+			seq_printf(m, "0x%04X: ", i);
+			break;
+		}
+
+		udelay(10);
+
+		switch (info->rd_byte) {
+		case 1:
+		default:
+			val8 = rtw89_read8_mask(rtwdev,
+						info->rd_addr, info->rd_msk);
+			seq_printf(m, "0x%02X\n", val8);
+			break;
+		case 2:
+			val16 = rtw89_read16_mask(rtwdev,
+						  info->rd_addr, info->rd_msk);
+			seq_printf(m, "0x%04X\n", val16);
+			break;
+		case 4:
+			val32 = rtw89_read32_mask(rtwdev,
+						  info->rd_addr, info->rd_msk);
+			seq_printf(m, "0x%08X\n", val32);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int rtw89_debug_mac_dump_dbg_port(struct rtw89_dev *rtwdev,
+					 struct seq_file *m)
+{
+	u32 sel;
+	int ret = 0;
+
+	for (sel = RTW89_DBG_PORT_SEL_PTCL_C0;
+	     sel < RTW89_DBG_PORT_SEL_LAST; sel++) {
+		if (!is_dbg_port_valid(rtwdev, sel))
+			continue;
+		ret = rtw89_debug_mac_dbg_port_dump(rtwdev, m, sel);
+		if (ret) {
+			rtw89_err(rtwdev,
+				  "failed to dump debug port %d\n", sel);
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int
+rtw89_debug_priv_mac_dbg_port_dump_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+
+	if (debugfs_priv->dbgpkg_en.ss_dbg)
+		rtw89_debug_mac_dump_ss_dbg(rtwdev, m);
+	if (debugfs_priv->dbgpkg_en.dle_dbg)
+		rtw89_debug_mac_dump_dle_dbg(rtwdev, m);
+	if (debugfs_priv->dbgpkg_en.dmac_dbg)
+		rtw89_debug_mac_dump_dmac_dbg(rtwdev, m);
+	if (debugfs_priv->dbgpkg_en.cmac_dbg)
+		rtw89_debug_mac_dump_cmac_dbg(rtwdev, m);
+	if (debugfs_priv->dbgpkg_en.dbg_port)
+		rtw89_debug_mac_dump_dbg_port(rtwdev, m);
+
+	return 0;
+};
+
+static u8 *rtw89_hex2bin_user(struct rtw89_dev *rtwdev,
+			      const char __user *user_buf, size_t count)
+{
+	char *buf;
+	u8 *bin;
+	int num;
+	int err = 0;
+
+	buf = memdup_user(user_buf, count);
+	if (IS_ERR(buf))
+		return buf;
+
+	num = count / 2;
+	bin = kmalloc(num, GFP_KERNEL);
+	if (!bin) {
+		err = -EFAULT;
+		goto out;
+	}
+
+	if (hex2bin(bin, buf, num)) {
+		rtw89_info(rtwdev, "valid format: H1H2H3...\n");
+		kfree(bin);
+		err = -EINVAL;
+	}
+
+out:
+	kfree(buf);
+
+	return err ? ERR_PTR(err) : bin;
+}
+
+static ssize_t rtw89_debug_priv_send_h2c_set(struct file *filp,
+					     const char __user *user_buf,
+					     size_t count, loff_t *loff)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = filp->private_data;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	u8 *h2c;
+	u16 h2c_len = count / 2;
+
+	h2c = rtw89_hex2bin_user(rtwdev, user_buf, count);
+	if (IS_ERR(h2c))
+		return -EFAULT;
+
+	rtw89_fw_h2c_raw(rtwdev, h2c, h2c_len);
+
+	kfree(h2c);
+
+	return count;
+}
+
+static int
+rtw89_debug_priv_early_h2c_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	struct rtw89_early_h2c *early_h2c;
+	int seq = 0;
+
+	mutex_lock(&rtwdev->mutex);
+	list_for_each_entry(early_h2c, &rtwdev->early_h2c_list, list)
+		seq_printf(m, "%d: %*ph\n", ++seq, early_h2c->h2c_len, early_h2c->h2c);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static ssize_t
+rtw89_debug_priv_early_h2c_set(struct file *filp, const char __user *user_buf,
+			       size_t count, loff_t *loff)
+{
+	struct seq_file *m = (struct seq_file *)filp->private_data;
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	struct rtw89_early_h2c *early_h2c;
+	u8 *h2c;
+	u16 h2c_len = count / 2;
+
+	h2c = rtw89_hex2bin_user(rtwdev, user_buf, count);
+	if (IS_ERR(h2c))
+		return -EFAULT;
+
+	if (h2c_len >= 2 && h2c[0] == 0x00 && h2c[1] == 0x00) {
+		kfree(h2c);
+		rtw89_fw_free_all_early_h2c(rtwdev);
+		goto out;
+	}
+
+	early_h2c = kmalloc(sizeof(*early_h2c), GFP_KERNEL);
+	if (!early_h2c) {
+		kfree(h2c);
+		return -EFAULT;
+	}
+
+	early_h2c->h2c = h2c;
+	early_h2c->h2c_len = h2c_len;
+
+	mutex_lock(&rtwdev->mutex);
+	list_add_tail(&early_h2c->list, &rtwdev->early_h2c_list);
+	mutex_unlock(&rtwdev->mutex);
+
+out:
+	return count;
+}
+
+static int rtw89_debug_priv_btc_info_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+
+	rtw89_btc_dump_info(rtwdev, m);
+
+	return 0;
+}
+
+static ssize_t rtw89_debug_priv_btc_manual_set(struct file *filp,
+					       const char __user *user_buf,
+					       size_t count, loff_t *loff)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = filp->private_data;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	struct rtw89_btc *btc = &rtwdev->btc;
+	bool btc_manual;
+
+	if (kstrtobool_from_user(user_buf, count, &btc_manual))
+		goto out;
+
+	btc->ctrl.manual = btc_manual;
+out:
+	return count;
+}
+
+static ssize_t rtw89_debug_fw_log_btc_manual_set(struct file *filp,
+						 const char __user *user_buf,
+						 size_t count, loff_t *loff)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = filp->private_data;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	struct rtw89_fw_info *fw_info = &rtwdev->fw;
+	bool fw_log_manual;
+
+	if (kstrtobool_from_user(user_buf, count, &fw_log_manual))
+		goto out;
+
+	mutex_lock(&rtwdev->mutex);
+	fw_info->fw_log_enable = fw_log_manual;
+	rtw89_fw_h2c_fw_log(rtwdev, fw_log_manual);
+	mutex_unlock(&rtwdev->mutex);
+out:
+	return count;
+}
+
+static void rtw89_sta_info_get_iter(void *data, struct ieee80211_sta *sta)
+{
+	static const char * const he_gi_str[] = {
+		[NL80211_RATE_INFO_HE_GI_0_8] = "0.8",
+		[NL80211_RATE_INFO_HE_GI_1_6] = "1.6",
+		[NL80211_RATE_INFO_HE_GI_3_2] = "3.2",
+	};
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rate_info *rate = &rtwsta->ra_report.txrate;
+	struct ieee80211_rx_status *status = &rtwsta->rx_status;
+	struct seq_file *m = (struct seq_file *)data;
+	u8 rssi;
+
+	seq_printf(m, "TX rate [%d]: ", rtwsta->mac_id);
+
+	if (rate->flags & RATE_INFO_FLAGS_MCS)
+		seq_printf(m, "HT MCS-%d%s", rate->mcs,
+			   rate->flags & RATE_INFO_FLAGS_SHORT_GI ? " SGI" : "");
+	else if (rate->flags & RATE_INFO_FLAGS_VHT_MCS)
+		seq_printf(m, "VHT %dSS MCS-%d%s", rate->nss, rate->mcs,
+			   rate->flags & RATE_INFO_FLAGS_SHORT_GI ? " SGI" : "");
+	else if (rate->flags & RATE_INFO_FLAGS_HE_MCS)
+		seq_printf(m, "HE %dSS MCS-%d GI:%s", rate->nss, rate->mcs,
+			   rate->he_gi <= NL80211_RATE_INFO_HE_GI_3_2 ?
+			   he_gi_str[rate->he_gi] : "N/A");
+	else
+		seq_printf(m, "Legacy %d", rate->legacy);
+	seq_printf(m, "\t(hw_rate=0x%x)", rtwsta->ra_report.hw_rate);
+	seq_printf(m, "\t==> agg_wait=%d (%d)\n", rtwsta->max_agg_wait,
+		   sta->max_rc_amsdu_len);
+
+	seq_printf(m, "RX rate [%d]: ", rtwsta->mac_id);
+
+	switch (status->encoding) {
+	case RX_ENC_LEGACY:
+		seq_printf(m, "Legacy %d", status->rate_idx +
+			   (status->band == NL80211_BAND_5GHZ ? 4 : 0));
+		break;
+	case RX_ENC_HT:
+		seq_printf(m, "HT MCS-%d%s", status->rate_idx,
+			   status->enc_flags & RX_ENC_FLAG_SHORT_GI ? " SGI" : "");
+		break;
+	case RX_ENC_VHT:
+		seq_printf(m, "VHT %dSS MCS-%d%s", status->nss, status->rate_idx,
+			   status->enc_flags & RX_ENC_FLAG_SHORT_GI ? " SGI" : "");
+		break;
+	case RX_ENC_HE:
+		seq_printf(m, "HE %dSS MCS-%d GI:%s", status->nss, status->rate_idx,
+			   status->he_gi <= NL80211_RATE_INFO_HE_GI_3_2 ?
+			   he_gi_str[rate->he_gi] : "N/A");
+		break;
+	}
+	seq_printf(m, "\t(hw_rate=0x%x)\n", rtwsta->rx_hw_rate);
+
+	rssi = ewma_rssi_read(&rtwsta->avg_rssi);
+	seq_printf(m, "RSSI: %d dBm (raw=%d, prev=%d)\n",
+		   RTW89_RSSI_RAW_TO_DBM(rssi), rssi, rtwsta->prev_rssi);
+}
+
+static void
+rtw89_debug_append_rx_rate(struct seq_file *m, struct rtw89_pkt_stat *pkt_stat,
+			   enum rtw89_hw_rate first_rate, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		seq_printf(m, "%s%u", i == 0 ? "" : ", ",
+			   pkt_stat->rx_rate_cnt[first_rate + i]);
+}
+
+static const struct rtw89_rx_rate_cnt_info {
+	enum rtw89_hw_rate first_rate;
+	int len;
+	const char *rate_mode;
+} rtw89_rx_rate_cnt_infos[] = {
+	{RTW89_HW_RATE_CCK1, 4, "Legacy:"},
+	{RTW89_HW_RATE_OFDM6, 8, "OFDM:"},
+	{RTW89_HW_RATE_MCS0, 8, "HT 0:"},
+	{RTW89_HW_RATE_MCS8, 8, "HT 1:"},
+	{RTW89_HW_RATE_VHT_NSS1_MCS0, 10, "VHT 1SS:"},
+	{RTW89_HW_RATE_VHT_NSS2_MCS0, 10, "VHT 2SS:"},
+	{RTW89_HW_RATE_HE_NSS1_MCS0, 12, "HE 1SS:"},
+	{RTW89_HW_RATE_HE_NSS2_MCS0, 12, "HE 2ss:"},
+};
+
+static int rtw89_debug_priv_phy_info_get(struct seq_file *m, void *v)
+{
+	struct rtw89_debugfs_priv *debugfs_priv = m->private;
+	struct rtw89_dev *rtwdev = debugfs_priv->rtwdev;
+	struct rtw89_traffic_stats *stats = &rtwdev->stats;
+	struct rtw89_pkt_stat *pkt_stat = &rtwdev->phystat.last_pkt_stat;
+	const struct rtw89_rx_rate_cnt_info *info;
+	int i;
+
+	seq_printf(m, "TP TX: %u [%u] Mbps (lv: %d), RX: %u [%u] Mbps (lv: %d)\n",
+		   stats->tx_throughput, stats->tx_throughput_raw, stats->tx_tfc_lv,
+		   stats->rx_throughput, stats->rx_throughput_raw, stats->rx_tfc_lv);
+	seq_printf(m, "Beacon: %u\n", pkt_stat->beacon_nr);
+	seq_printf(m, "Avg packet length: TX=%u, RX=%u\n", stats->tx_avg_len,
+		   stats->rx_avg_len);
+
+	seq_puts(m, "RX count:\n");
+	for (i = 0; i < ARRAY_SIZE(rtw89_rx_rate_cnt_infos); i++) {
+		info = &rtw89_rx_rate_cnt_infos[i];
+		seq_printf(m, "%10s [", info->rate_mode);
+		rtw89_debug_append_rx_rate(m, pkt_stat,
+					   info->first_rate, info->len);
+		seq_puts(m, "]\n");
+	}
+
+	ieee80211_iterate_stations_atomic(rtwdev->hw, rtw89_sta_info_get_iter, m);
+
+	return 0;
+}
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_read_reg = {
+	.cb_read = rtw89_debug_priv_read_reg_get,
+	.cb_write = rtw89_debug_priv_read_reg_select,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_write_reg = {
+	.cb_write = rtw89_debug_priv_write_reg_set,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_read_rf = {
+	.cb_read = rtw89_debug_priv_read_rf_get,
+	.cb_write = rtw89_debug_priv_read_rf_select,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_write_rf = {
+	.cb_write = rtw89_debug_priv_write_rf_set,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_rf_reg_dump = {
+	.cb_read = rtw89_debug_priv_rf_reg_dump_get,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_txpwr_table = {
+	.cb_read = rtw89_debug_priv_txpwr_table_get,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_mac_reg_dump = {
+	.cb_read = rtw89_debug_priv_mac_reg_dump_get,
+	.cb_write = rtw89_debug_priv_mac_reg_dump_select,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_mac_mem_dump = {
+	.cb_read = rtw89_debug_priv_mac_mem_dump_get,
+	.cb_write = rtw89_debug_priv_mac_mem_dump_select,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_mac_dbg_port_dump = {
+	.cb_read = rtw89_debug_priv_mac_dbg_port_dump_get,
+	.cb_write = rtw89_debug_priv_mac_dbg_port_dump_select,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_send_h2c = {
+	.cb_write = rtw89_debug_priv_send_h2c_set,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_early_h2c = {
+	.cb_read = rtw89_debug_priv_early_h2c_get,
+	.cb_write = rtw89_debug_priv_early_h2c_set,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_btc_info = {
+	.cb_read = rtw89_debug_priv_btc_info_get,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_btc_manual = {
+	.cb_write = rtw89_debug_priv_btc_manual_set,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_fw_log_manual = {
+	.cb_write = rtw89_debug_fw_log_btc_manual_set,
+};
+
+static struct rtw89_debugfs_priv rtw89_debug_priv_phy_info = {
+	.cb_read = rtw89_debug_priv_phy_info_get,
+};
+
+#define rtw89_debugfs_add(name, mode, fopname, parent)				\
+	do {									\
+		rtw89_debug_priv_ ##name.rtwdev = rtwdev;			\
+		if (!debugfs_create_file(#name, mode,				\
+					 parent, &rtw89_debug_priv_ ##name,	\
+					 &file_ops_ ##fopname))			\
+			pr_debug("Unable to initialize debugfs:%s\n", #name);	\
+	} while (0)
+
+#define rtw89_debugfs_add_w(name)						\
+	rtw89_debugfs_add(name, S_IFREG | 0222, single_w, debugfs_topdir)
+#define rtw89_debugfs_add_rw(name)						\
+	rtw89_debugfs_add(name, S_IFREG | 0666, common_rw, debugfs_topdir)
+#define rtw89_debugfs_add_r(name)						\
+	rtw89_debugfs_add(name, S_IFREG | 0444, single_r, debugfs_topdir)
+
+void rtw89_debugfs_init(struct rtw89_dev *rtwdev)
+{
+	struct dentry *debugfs_topdir;
+
+	debugfs_topdir = debugfs_create_dir("rtw89",
+					    rtwdev->hw->wiphy->debugfsdir);
+
+	rtw89_debugfs_add_rw(read_reg);
+	rtw89_debugfs_add_w(write_reg);
+	rtw89_debugfs_add_rw(read_rf);
+	rtw89_debugfs_add_w(write_rf);
+	rtw89_debugfs_add_r(rf_reg_dump);
+	rtw89_debugfs_add_r(txpwr_table);
+	rtw89_debugfs_add_rw(mac_reg_dump);
+	rtw89_debugfs_add_rw(mac_mem_dump);
+	rtw89_debugfs_add_rw(mac_dbg_port_dump);
+	rtw89_debugfs_add_w(send_h2c);
+	rtw89_debugfs_add_rw(early_h2c);
+	rtw89_debugfs_add_r(btc_info);
+	rtw89_debugfs_add_w(btc_manual);
+	rtw89_debugfs_add_w(fw_log_manual);
+	rtw89_debugfs_add_r(phy_info);
+}
+#endif
+
+#ifdef CONFIG_RTW89_DEBUGMSG
+void __rtw89_debug(struct rtw89_dev *rtwdev,
+		   enum rtw89_debug_mask mask,
+		   const char *fmt, ...)
+{
+	struct va_format vaf = {
+	.fmt = fmt,
+	};
+
+	va_list args;
+
+	va_start(args, fmt);
+	vaf.va = &args;
+
+	if (rtw89_debug_mask & mask)
+		dev_printk(KERN_DEBUG, rtwdev->dev, "%pV", &vaf);
+
+	va_end(args);
+}
+EXPORT_SYMBOL(__rtw89_debug);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/debug.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_DEBUG_H__
+#define __RTW89_DEBUG_H__
+
+#include "core.h"
+
+enum rtw89_debug_mask {
+	RTW89_DBG_TXRX = BIT(0),
+	RTW89_DBG_RFK = BIT(1),
+	RTW89_DBG_RFK_TRACK = BIT(2),
+	RTW89_DBG_CFO = BIT(3),
+	RTW89_DBG_TSSI = BIT(4),
+	RTW89_DBG_TXPWR = BIT(5),
+	RTW89_DBG_HCI = BIT(6),
+	RTW89_DBG_RA = BIT(7),
+	RTW89_DBG_REGD = BIT(8),
+	RTW89_DBG_PHY_TRACK = BIT(9),
+	RTW89_DBG_DIG = BIT(10),
+	RTW89_DBG_SER = BIT(11),
+	RTW89_DBG_FW = BIT(12),
+	RTW89_DBG_BTC = BIT(13),
+	RTW89_DBG_BF = BIT(14),
+};
+
+enum rtw89_debug_mac_reg_sel {
+	RTW89_DBG_SEL_MAC_00,
+	RTW89_DBG_SEL_MAC_40,
+	RTW89_DBG_SEL_MAC_80,
+	RTW89_DBG_SEL_MAC_C0,
+	RTW89_DBG_SEL_MAC_E0,
+	RTW89_DBG_SEL_BB,
+	RTW89_DBG_SEL_IQK,
+	RTW89_DBG_SEL_RFC,
+};
+
+#ifdef CONFIG_RTW89_DEBUGFS
+void rtw89_debugfs_init(struct rtw89_dev *rtwdev);
+#else
+static inline void rtw89_debugfs_init(struct rtw89_dev *rtwdev) {}
+#endif
+
+#define rtw89_info(rtwdev, a...) dev_info((rtwdev)->dev, ##a)
+#define rtw89_warn(rtwdev, a...) dev_warn((rtwdev)->dev, ##a)
+#define rtw89_err(rtwdev, a...) dev_err((rtwdev)->dev, ##a)
+
+#ifdef CONFIG_RTW89_DEBUGMSG
+extern unsigned int rtw89_debug_mask;
+#define rtw89_debug(rtwdev, a...) __rtw89_debug(rtwdev, ##a)
+
+__printf(3, 4)
+void __rtw89_debug(struct rtw89_dev *rtwdev,
+		   enum rtw89_debug_mask mask,
+		   const char *fmt, ...);
+static inline void rtw89_hex_dump(struct rtw89_dev *rtwdev,
+				  enum rtw89_debug_mask mask,
+				  const char *prefix_str,
+				  const void *buf, size_t len)
+{
+	if (!(rtw89_debug_mask & mask))
+		return;
+
+	print_hex_dump_bytes(prefix_str, DUMP_PREFIX_OFFSET, buf, len);
+}
+#else
+static inline void rtw89_debug(struct rtw89_dev *rtwdev,
+			       enum rtw89_debug_mask mask,
+			       const char *fmt, ...) {}
+static inline void rtw89_hex_dump(struct rtw89_dev *rtwdev,
+				  enum rtw89_debug_mask mask,
+				  const char *prefix_str,
+				  const void *buf, size_t len) {}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/efuse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/efuse.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "debug.h"
+#include "efuse.h"
+#include "reg.h"
+
+enum rtw89_efuse_bank {
+	RTW89_EFUSE_BANK_WIFI,
+	RTW89_EFUSE_BANK_BT,
+};
+
+static int rtw89_switch_efuse_bank(struct rtw89_dev *rtwdev,
+				   enum rtw89_efuse_bank bank)
+{
+	u8 val;
+
+	val = rtw89_read32_mask(rtwdev, R_AX_EFUSE_CTRL_1,
+				B_AX_EF_CELL_SEL_MASK);
+	if (bank == val)
+		return 0;
+
+	rtw89_write32_mask(rtwdev, R_AX_EFUSE_CTRL_1, B_AX_EF_CELL_SEL_MASK,
+			   bank);
+
+	val = rtw89_read32_mask(rtwdev, R_AX_EFUSE_CTRL_1,
+				B_AX_EF_CELL_SEL_MASK);
+	if (bank == val)
+		return 0;
+
+	return -EBUSY;
+}
+
+static int rtw89_dump_physical_efuse_map(struct rtw89_dev *rtwdev, u8 *map,
+					 u32 dump_addr, u32 dump_size)
+{
+	u32 efuse_ctl;
+	u32 addr;
+	int ret;
+
+	rtw89_switch_efuse_bank(rtwdev, RTW89_EFUSE_BANK_WIFI);
+
+	for (addr = dump_addr; addr < dump_addr + dump_size; addr++) {
+		efuse_ctl = u32_encode_bits(addr, B_AX_EF_ADDR_MASK);
+		rtw89_write32(rtwdev, R_AX_EFUSE_CTRL, efuse_ctl & ~B_AX_EF_RDY);
+
+		ret = read_poll_timeout_atomic(rtw89_read32, efuse_ctl,
+					       efuse_ctl & B_AX_EF_RDY, 1, 1000000,
+					       true, rtwdev, R_AX_EFUSE_CTRL);
+		if (ret)
+			return -EBUSY;
+
+		*map++ = (u8)(efuse_ctl & 0xff);
+	}
+
+	return 0;
+}
+
+#define invalid_efuse_header(hdr1, hdr2) \
+	((hdr1) == 0xff || (hdr2) == 0xff)
+#define invalid_efuse_content(word_en, i) \
+	(((word_en) & BIT(i)) != 0x0)
+#define get_efuse_blk_idx(hdr1, hdr2) \
+	((((hdr2) & 0xf0) >> 4) | (((hdr1) & 0x0f) << 4))
+#define block_idx_to_logical_idx(blk_idx, i) \
+	(((blk_idx) << 3) + ((i) << 1))
+static int rtw89_dump_logical_efuse_map(struct rtw89_dev *rtwdev, u8 *phy_map,
+					u8 *log_map)
+{
+	u32 physical_size = rtwdev->chip->physical_efuse_size;
+	u32 logical_size = rtwdev->chip->logical_efuse_size;
+	u8 sec_ctrl_size = rtwdev->chip->sec_ctrl_efuse_size;
+	u32 phy_idx = sec_ctrl_size;
+	u32 log_idx;
+	u8 hdr1, hdr2;
+	u8 blk_idx;
+	u8 word_en;
+	int i;
+
+	while (phy_idx < physical_size - sec_ctrl_size) {
+		hdr1 = phy_map[phy_idx];
+		hdr2 = phy_map[phy_idx + 1];
+		if (invalid_efuse_header(hdr1, hdr2))
+			break;
+
+		blk_idx = get_efuse_blk_idx(hdr1, hdr2);
+		word_en = hdr2 & 0xf;
+		phy_idx += 2;
+
+		for (i = 0; i < 4; i++) {
+			if (invalid_efuse_content(word_en, i))
+				continue;
+
+			log_idx = block_idx_to_logical_idx(blk_idx, i);
+			if (phy_idx + 1 > physical_size - sec_ctrl_size - 1 ||
+			    log_idx + 1 > logical_size)
+				return -EINVAL;
+
+			log_map[log_idx] = phy_map[phy_idx];
+			log_map[log_idx + 1] = phy_map[phy_idx + 1];
+			phy_idx += 2;
+		}
+	}
+	return 0;
+}
+
+int rtw89_parse_efuse_map(struct rtw89_dev *rtwdev)
+{
+	u32 phy_size = rtwdev->chip->physical_efuse_size;
+	u32 log_size = rtwdev->chip->logical_efuse_size;
+	u8 *phy_map = NULL;
+	u8 *log_map = NULL;
+	int ret;
+
+	if (rtw89_read16(rtwdev, R_AX_SYS_WL_EFUSE_CTRL) & B_AX_AUTOLOAD_SUS)
+		rtwdev->efuse.valid = true;
+	else
+		rtw89_warn(rtwdev, "failed to check efuse autoload\n");
+
+	phy_map = kmalloc(phy_size, GFP_KERNEL);
+	log_map = kmalloc(log_size, GFP_KERNEL);
+
+	if (!phy_map || !log_map) {
+		ret = -ENOMEM;
+		goto out_free;
+	}
+
+	ret = rtw89_dump_physical_efuse_map(rtwdev, phy_map, 0, phy_size);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to dump efuse physical map\n");
+		goto out_free;
+	}
+
+	memset(log_map, 0xff, log_size);
+	ret = rtw89_dump_logical_efuse_map(rtwdev, phy_map, log_map);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to dump efuse logical map\n");
+		goto out_free;
+	}
+
+	rtw89_hex_dump(rtwdev, RTW89_DBG_FW, "log_map: ", log_map, log_size);
+
+	ret = rtwdev->chip->ops->read_efuse(rtwdev, log_map);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to read efuse map\n");
+		goto out_free;
+	}
+
+out_free:
+	kfree(log_map);
+	kfree(phy_map);
+
+	return ret;
+}
+
+int rtw89_parse_phycap_map(struct rtw89_dev *rtwdev)
+{
+	u32 phycap_addr = rtwdev->chip->phycap_addr;
+	u32 phycap_size = rtwdev->chip->phycap_size;
+	u8 *phycap_map = NULL;
+	int ret = 0;
+
+	if (!phycap_size)
+		return 0;
+
+	phycap_map = kmalloc(phycap_size, GFP_KERNEL);
+	if (!phycap_map)
+		return -ENOMEM;
+
+	ret = rtw89_dump_physical_efuse_map(rtwdev, phycap_map,
+					    phycap_addr, phycap_size);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to dump phycap map\n");
+		goto out_free;
+	}
+
+	ret = rtwdev->chip->ops->read_phycap(rtwdev, phycap_map);
+	if (ret) {
+		rtw89_warn(rtwdev, "failed to read phycap map\n");
+		goto out_free;
+	}
+
+out_free:
+	kfree(phycap_map);
+
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/efuse.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/efuse.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_EFUSE_H__
+#define __RTW89_EFUSE_H__
+
+#include "core.h"
+
+int rtw89_parse_efuse_map(struct rtw89_dev *rtwdev);
+int rtw89_parse_phycap_map(struct rtw89_dev *rtwdev);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/fw.c
@@ -0,0 +1,1655 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "cam.h"
+#include "coex.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+#include "phy.h"
+#include "reg.h"
+
+static struct sk_buff *rtw89_fw_h2c_alloc_skb(u32 len, bool header)
+{
+	struct sk_buff *skb;
+	u32 header_len = 0;
+
+	if (header)
+		header_len = H2C_HEADER_LEN;
+
+	skb = dev_alloc_skb(len + header_len + 24);
+	if (!skb)
+		return NULL;
+	skb_reserve(skb, header_len + 24);
+	memset(skb->data, 0, len);
+
+	return skb;
+}
+
+struct sk_buff *rtw89_fw_h2c_alloc_skb_with_hdr(u32 len)
+{
+	return rtw89_fw_h2c_alloc_skb(len, true);
+}
+
+struct sk_buff *rtw89_fw_h2c_alloc_skb_no_hdr(u32 len)
+{
+	return rtw89_fw_h2c_alloc_skb(len, false);
+}
+
+static u8 _fw_get_rdy(struct rtw89_dev *rtwdev)
+{
+	u8 val = rtw89_read8(rtwdev, R_AX_WCPU_FW_CTRL);
+
+	return FIELD_GET(B_AX_WCPU_FWDL_STS_MASK, val);
+}
+
+#define FWDL_WAIT_CNT 400000
+int rtw89_fw_check_rdy(struct rtw89_dev *rtwdev)
+{
+	u8 val;
+	int ret;
+
+	ret = read_poll_timeout_atomic(_fw_get_rdy, val,
+				       val == RTW89_FWDL_WCPU_FW_INIT_RDY,
+				       1, FWDL_WAIT_CNT, false, rtwdev);
+	if (ret) {
+		switch (val) {
+		case RTW89_FWDL_CHECKSUM_FAIL:
+			rtw89_err(rtwdev, "fw checksum fail\n");
+			return -EINVAL;
+
+		case RTW89_FWDL_SECURITY_FAIL:
+			rtw89_err(rtwdev, "fw security fail\n");
+			return -EINVAL;
+
+		case RTW89_FWDL_CV_NOT_MATCH:
+			rtw89_err(rtwdev, "fw cv not match\n");
+			return -EINVAL;
+
+		default:
+			return -EBUSY;
+		}
+	}
+
+	set_bit(RTW89_FLAG_FW_RDY, rtwdev->flags);
+
+	return 0;
+}
+
+static int rtw89_fw_hdr_parser(struct rtw89_dev *rtwdev, const u8 *fw, u32 len,
+			       struct rtw89_fw_bin_info *info)
+{
+	struct rtw89_fw_hdr_section_info *section_info;
+	const u8 *fw_end = fw + len;
+	const u8 *bin;
+	u32 i;
+
+	if (!info)
+		return -EINVAL;
+
+	info->section_num = GET_FW_HDR_SEC_NUM(fw);
+	info->hdr_len = RTW89_FW_HDR_SIZE +
+			info->section_num * RTW89_FW_SECTION_HDR_SIZE;
+	SET_FW_HDR_PART_SIZE(fw, FWDL_SECTION_PER_PKT_LEN);
+
+	bin = fw + info->hdr_len;
+
+	/* jump to section header */
+	fw += RTW89_FW_HDR_SIZE;
+	section_info = info->section_info;
+	for (i = 0; i < info->section_num; i++) {
+		section_info->len = GET_FWSECTION_HDR_SEC_SIZE(fw);
+		if (GET_FWSECTION_HDR_CHECKSUM(fw))
+			section_info->len += FWDL_SECTION_CHKSUM_LEN;
+		section_info->redl = GET_FWSECTION_HDR_REDL(fw);
+		section_info->dladdr =
+				GET_FWSECTION_HDR_DL_ADDR(fw) & 0x1fffffff;
+		section_info->addr = bin;
+		bin += section_info->len;
+		fw += RTW89_FW_SECTION_HDR_SIZE;
+		section_info++;
+	}
+
+	if (fw_end != bin) {
+		rtw89_err(rtwdev, "[ERR]fw bin size\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static
+int rtw89_mfw_recognize(struct rtw89_dev *rtwdev, enum rtw89_fw_type type,
+			struct rtw89_fw_suit *fw_suit)
+{
+	struct rtw89_fw_info *fw_info = &rtwdev->fw;
+	const u8 *mfw = fw_info->firmware->data;
+	u32 mfw_len = fw_info->firmware->size;
+	const struct rtw89_mfw_hdr *mfw_hdr = (const struct rtw89_mfw_hdr *)mfw;
+	const struct rtw89_mfw_info *mfw_info;
+	int i;
+
+	if (mfw_hdr->sig != RTW89_MFW_SIG) {
+		rtw89_debug(rtwdev, RTW89_DBG_FW, "use legacy firmware\n");
+		/* legacy firmware support normal type only */
+		if (type != RTW89_FW_NORMAL)
+			return -EINVAL;
+		fw_suit->data = mfw;
+		fw_suit->size = mfw_len;
+		return 0;
+	}
+
+	for (i = 0; i < mfw_hdr->fw_nr; i++) {
+		mfw_info = &mfw_hdr->info[i];
+		if (mfw_info->cv != rtwdev->hal.cv ||
+		    mfw_info->type != type ||
+		    mfw_info->mp)
+			continue;
+
+		fw_suit->data = mfw + le32_to_cpu(mfw_info->shift);
+		fw_suit->size = le32_to_cpu(mfw_info->size);
+		return 0;
+	}
+
+	rtw89_err(rtwdev, "no suitable firmware found\n");
+	return -ENOENT;
+}
+
+static void rtw89_fw_update_ver(struct rtw89_dev *rtwdev,
+				enum rtw89_fw_type type,
+				struct rtw89_fw_suit *fw_suit)
+{
+	const u8 *hdr = fw_suit->data;
+
+	fw_suit->major_ver = GET_FW_HDR_MAJOR_VERSION(hdr);
+	fw_suit->minor_ver = GET_FW_HDR_MINOR_VERSION(hdr);
+	fw_suit->sub_ver = GET_FW_HDR_SUBVERSION(hdr);
+	fw_suit->sub_idex = GET_FW_HDR_SUBINDEX(hdr);
+	fw_suit->build_year = GET_FW_HDR_YEAR(hdr);
+	fw_suit->build_mon = GET_FW_HDR_MONTH(hdr);
+	fw_suit->build_date = GET_FW_HDR_DATE(hdr);
+	fw_suit->build_hour = GET_FW_HDR_HOUR(hdr);
+	fw_suit->build_min = GET_FW_HDR_MIN(hdr);
+	fw_suit->cmd_ver = GET_FW_HDR_CMD_VERSERION(hdr);
+
+	rtw89_info(rtwdev,
+		   "Firmware version %u.%u.%u.%u, cmd version %u, type %u\n",
+		   fw_suit->major_ver, fw_suit->minor_ver, fw_suit->sub_ver,
+		   fw_suit->sub_idex, fw_suit->cmd_ver, type);
+}
+
+static
+int __rtw89_fw_recognize(struct rtw89_dev *rtwdev, enum rtw89_fw_type type)
+{
+	struct rtw89_fw_suit *fw_suit = rtw89_fw_suit_get(rtwdev, type);
+	int ret;
+
+	ret = rtw89_mfw_recognize(rtwdev, type, fw_suit);
+	if (ret)
+		return ret;
+
+	rtw89_fw_update_ver(rtwdev, type, fw_suit);
+
+	return 0;
+}
+
+static void rtw89_fw_recognize_features(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_fw_suit *fw_suit = rtw89_fw_suit_get(rtwdev, RTW89_FW_NORMAL);
+
+	if (chip->chip_id == RTL8852A &&
+	    RTW89_FW_SUIT_VER_CODE(fw_suit) <= RTW89_FW_VER_CODE(0, 13, 29, 0))
+		rtwdev->fw.old_ht_ra_format = true;
+}
+
+int rtw89_fw_recognize(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = __rtw89_fw_recognize(rtwdev, RTW89_FW_NORMAL);
+	if (ret)
+		return ret;
+
+	/* It still works if wowlan firmware isn't existing. */
+	__rtw89_fw_recognize(rtwdev, RTW89_FW_WOWLAN);
+
+	rtw89_fw_recognize_features(rtwdev);
+
+	return 0;
+}
+
+void rtw89_h2c_pkt_set_hdr(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			   u8 type, u8 cat, u8 class, u8 func,
+			   bool rack, bool dack, u32 len)
+{
+	struct fwcmd_hdr *hdr;
+
+	hdr = (struct fwcmd_hdr *)skb_push(skb, 8);
+
+	if (!(rtwdev->fw.h2c_seq % 4))
+		rack = true;
+	hdr->hdr0 = cpu_to_le32(FIELD_PREP(H2C_HDR_DEL_TYPE, type) |
+				FIELD_PREP(H2C_HDR_CAT, cat) |
+				FIELD_PREP(H2C_HDR_CLASS, class) |
+				FIELD_PREP(H2C_HDR_FUNC, func) |
+				FIELD_PREP(H2C_HDR_H2C_SEQ, rtwdev->fw.h2c_seq));
+
+	hdr->hdr1 = cpu_to_le32(FIELD_PREP(H2C_HDR_TOTAL_LEN,
+					   len + H2C_HEADER_LEN) |
+				(rack ? H2C_HDR_REC_ACK : 0) |
+				(dack ? H2C_HDR_DONE_ACK : 0));
+
+	rtwdev->fw.h2c_seq++;
+}
+
+static void rtw89_h2c_pkt_set_hdr_fwdl(struct rtw89_dev *rtwdev,
+				       struct sk_buff *skb,
+				       u8 type, u8 cat, u8 class, u8 func,
+				       u32 len)
+{
+	struct fwcmd_hdr *hdr;
+
+	hdr = (struct fwcmd_hdr *)skb_push(skb, 8);
+
+	hdr->hdr0 = cpu_to_le32(FIELD_PREP(H2C_HDR_DEL_TYPE, type) |
+				FIELD_PREP(H2C_HDR_CAT, cat) |
+				FIELD_PREP(H2C_HDR_CLASS, class) |
+				FIELD_PREP(H2C_HDR_FUNC, func) |
+				FIELD_PREP(H2C_HDR_H2C_SEQ, rtwdev->fw.h2c_seq));
+
+	hdr->hdr1 = cpu_to_le32(FIELD_PREP(H2C_HDR_TOTAL_LEN,
+					   len + H2C_HEADER_LEN));
+}
+
+static int __rtw89_fw_download_hdr(struct rtw89_dev *rtwdev, const u8 *fw, u32 len)
+{
+	struct sk_buff *skb;
+	u32 ret = 0;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(len);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw hdr dl\n");
+		return -ENOMEM;
+	}
+
+	skb_put_data(skb, fw, len);
+	rtw89_h2c_pkt_set_hdr_fwdl(rtwdev, skb, FWCMD_TYPE_H2C,
+				   H2C_CAT_MAC, H2C_CL_MAC_FWDL,
+				   H2C_FUNC_MAC_FWHDR_DL, len);
+
+	ret = rtw89_h2c_tx(rtwdev, skb, false);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		ret = -1;
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return ret;
+}
+
+static int rtw89_fw_download_hdr(struct rtw89_dev *rtwdev, const u8 *fw, u32 len)
+{
+	u8 val;
+	int ret;
+
+	ret = __rtw89_fw_download_hdr(rtwdev, fw, len);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]FW header download\n");
+		return ret;
+	}
+
+	ret = read_poll_timeout_atomic(rtw89_read8, val, val & B_AX_FWDL_PATH_RDY,
+				       1, FWDL_WAIT_CNT, false,
+				       rtwdev, R_AX_WCPU_FW_CTRL);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]FWDL path ready\n");
+		return ret;
+	}
+
+	rtw89_write32(rtwdev, R_AX_HALT_H2C_CTRL, 0);
+	rtw89_write32(rtwdev, R_AX_HALT_C2H_CTRL, 0);
+
+	return 0;
+}
+
+static int __rtw89_fw_download_main(struct rtw89_dev *rtwdev,
+				    struct rtw89_fw_hdr_section_info *info)
+{
+	struct sk_buff *skb;
+	const u8 *section = info->addr;
+	u32 residue_len = info->len;
+	u32 pkt_len;
+	int ret;
+
+	while (residue_len) {
+		if (residue_len >= FWDL_SECTION_PER_PKT_LEN)
+			pkt_len = FWDL_SECTION_PER_PKT_LEN;
+		else
+			pkt_len = residue_len;
+
+		skb = rtw89_fw_h2c_alloc_skb_no_hdr(pkt_len);
+		if (!skb) {
+			rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+			return -ENOMEM;
+		}
+		skb_put_data(skb, section, pkt_len);
+
+		ret = rtw89_h2c_tx(rtwdev, skb, true);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to send h2c\n");
+			ret = -1;
+			goto fail;
+		}
+
+		section += pkt_len;
+		residue_len -= pkt_len;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return ret;
+}
+
+static int rtw89_fw_download_main(struct rtw89_dev *rtwdev, const u8 *fw,
+				  struct rtw89_fw_bin_info *info)
+{
+	struct rtw89_fw_hdr_section_info *section_info = info->section_info;
+	u8 section_num = info->section_num;
+	int ret;
+
+	while (section_num--) {
+		ret = __rtw89_fw_download_main(rtwdev, section_info);
+		if (ret)
+			return ret;
+		section_info++;
+	}
+
+	mdelay(5);
+
+	ret = rtw89_fw_check_rdy(rtwdev);
+	if (ret) {
+		rtw89_warn(rtwdev, "download firmware fail\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void rtw89_fw_prog_cnt_dump(struct rtw89_dev *rtwdev)
+{
+	u32 val32;
+	u16 index;
+
+	rtw89_write32(rtwdev, R_AX_DBG_CTRL,
+		      FIELD_PREP(B_AX_DBG_SEL0, FW_PROG_CNTR_DBG_SEL) |
+		      FIELD_PREP(B_AX_DBG_SEL1, FW_PROG_CNTR_DBG_SEL));
+	rtw89_write32_mask(rtwdev, R_AX_SYS_STATUS1, B_AX_SEL_0XC0_MASK, MAC_DBG_SEL);
+
+	for (index = 0; index < 15; index++) {
+		val32 = rtw89_read32(rtwdev, R_AX_DBG_PORT_SEL);
+		rtw89_err(rtwdev, "[ERR]fw PC = 0x%x\n", val32);
+		fsleep(10);
+	}
+}
+
+static void rtw89_fw_dl_fail_dump(struct rtw89_dev *rtwdev)
+{
+	u32 val32;
+
+	val32 = rtw89_read32(rtwdev, R_AX_WCPU_FW_CTRL);
+	rtw89_err(rtwdev, "[ERR]fwdl 0x1E0 = 0x%x\n", val32);
+
+	val32 = rtw89_read32(rtwdev, R_AX_BOOT_DBG);
+	rtw89_err(rtwdev, "[ERR]fwdl 0x83F0 = 0x%x\n", val32);
+
+	rtw89_fw_prog_cnt_dump(rtwdev);
+}
+
+static
+int __rtw89_fw_download(struct rtw89_dev *rtwdev, enum rtw89_fw_type type)
+{
+	struct rtw89_fw_info *fw_info = &rtwdev->fw;
+	struct rtw89_fw_suit *fw_suit = rtw89_fw_suit_get(rtwdev, type);
+	struct rtw89_fw_bin_info info;
+	const u8 *fw = fw_suit->data;
+	u32 len = fw_suit->size;
+	u8 val;
+	int ret;
+
+	if (!fw || !len) {
+		rtw89_err(rtwdev, "fw type %d isn't recognized\n", type);
+		return -ENOENT;
+	}
+
+	ret = rtw89_fw_hdr_parser(rtwdev, fw, len, &info);
+	if (ret) {
+		rtw89_err(rtwdev, "parse fw header fail\n");
+		goto fwdl_err;
+	}
+
+	ret = read_poll_timeout_atomic(rtw89_read8, val, val & B_AX_H2C_PATH_RDY,
+				       1, FWDL_WAIT_CNT, false,
+				       rtwdev, R_AX_WCPU_FW_CTRL);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]H2C path ready\n");
+		goto fwdl_err;
+	}
+
+	ret = rtw89_fw_download_hdr(rtwdev, fw, info.hdr_len);
+	if (ret) {
+		ret = -EBUSY;
+		goto fwdl_err;
+	}
+
+	ret = rtw89_fw_download_main(rtwdev, fw, &info);
+	if (ret) {
+		ret = -EBUSY;
+		goto fwdl_err;
+	}
+
+	fw_info->h2c_seq = 0;
+	fw_info->rec_seq = 0;
+	rtwdev->mac.rpwm_seq_num = RPWM_SEQ_NUM_MAX;
+	rtwdev->mac.cpwm_seq_num = CPWM_SEQ_NUM_MAX;
+
+	return ret;
+
+fwdl_err:
+	rtw89_fw_dl_fail_dump(rtwdev);
+	return ret;
+}
+
+int rtw89_fw_download(struct rtw89_dev *rtwdev, enum rtw89_fw_type type)
+{
+	int retry;
+	int ret;
+
+	for (retry = 0; retry < 5; retry++) {
+		ret = __rtw89_fw_download(rtwdev, type);
+		if (!ret)
+			return 0;
+	}
+
+	return ret;
+}
+
+int rtw89_wait_firmware_completion(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_fw_info *fw = &rtwdev->fw;
+
+	wait_for_completion(&fw->completion);
+	if (!fw->firmware)
+		return -EINVAL;
+
+	return 0;
+}
+
+static void rtw89_load_firmware_cb(const struct firmware *firmware, void *context)
+{
+	struct rtw89_fw_info *fw = context;
+	struct rtw89_dev *rtwdev = fw->rtwdev;
+
+	if (!firmware || !firmware->data) {
+		rtw89_err(rtwdev, "failed to request firmware\n");
+		complete_all(&fw->completion);
+		return;
+	}
+
+	fw->firmware = firmware;
+	complete_all(&fw->completion);
+}
+
+int rtw89_load_firmware(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_fw_info *fw = &rtwdev->fw;
+	const char *fw_name = rtwdev->chip->fw_name;
+	int ret;
+
+	fw->rtwdev = rtwdev;
+	init_completion(&fw->completion);
+
+	ret = request_firmware_nowait(THIS_MODULE, true, fw_name, rtwdev->dev,
+				      GFP_KERNEL, fw, rtw89_load_firmware_cb);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to async firmware request\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+void rtw89_unload_firmware(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_fw_info *fw = &rtwdev->fw;
+
+	rtw89_wait_firmware_completion(rtwdev);
+
+	if (fw->firmware)
+		release_firmware(fw->firmware);
+}
+
+#define H2C_CAM_LEN 60
+int rtw89_fw_h2c_cam(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_CAM_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_CAM_LEN);
+	rtw89_cam_fill_addr_cam_info(rtwdev, rtwvif, skb->data);
+	rtw89_cam_fill_bssid_cam_info(rtwdev, rtwvif, skb->data);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_MAC_ADDR_CAM_UPDATE,
+			      H2C_FUNC_MAC_ADDR_CAM_UPD, 0, 1,
+			      H2C_CAM_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_BA_CAM_LEN 4
+int rtw89_fw_h2c_ba_cam(struct rtw89_dev *rtwdev, bool valid, u8 macid,
+			struct ieee80211_ampdu_params *params)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_BA_CAM_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c ba cam\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_BA_CAM_LEN);
+	SET_BA_CAM_MACID(skb->data, macid);
+	if (!valid)
+		goto end;
+	SET_BA_CAM_VALID(skb->data, valid);
+	SET_BA_CAM_TID(skb->data, params->tid);
+	if (params->buf_size > 64)
+		SET_BA_CAM_BMAP_SIZE(skb->data, 4);
+	else
+		SET_BA_CAM_BMAP_SIZE(skb->data, 0);
+	/* If init req is set, hw will set the ssn */
+	SET_BA_CAM_INIT_REQ(skb->data, 0);
+	SET_BA_CAM_SSN(skb->data, params->ssn);
+
+end:
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_BA_CAM,
+			      H2C_FUNC_MAC_BA_CAM, 0, 1,
+			      H2C_BA_CAM_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_LOG_CFG_LEN 12
+int rtw89_fw_h2c_fw_log(struct rtw89_dev *rtwdev, bool enable)
+{
+	struct sk_buff *skb;
+	u32 comp = enable ? BIT(RTW89_FW_LOG_COMP_INIT) | BIT(RTW89_FW_LOG_COMP_TASK) |
+			    BIT(RTW89_FW_LOG_COMP_PS) | BIT(RTW89_FW_LOG_COMP_ERROR) : 0;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_LOG_CFG_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw log cfg\n");
+		return -ENOMEM;
+	}
+
+	skb_put(skb, H2C_LOG_CFG_LEN);
+	SET_LOG_CFG_LEVEL(skb->data, RTW89_FW_LOG_LEVEL_SER);
+	SET_LOG_CFG_PATH(skb->data, BIT(RTW89_FW_LOG_LEVEL_C2H));
+	SET_LOG_CFG_COMP(skb->data, comp);
+	SET_LOG_CFG_COMP_EXT(skb->data, 0);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_FW_INFO,
+			      H2C_FUNC_LOG_CFG, 0, 0,
+			      H2C_LOG_CFG_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_GENERAL_PKT_LEN 6
+#define H2C_GENERAL_PKT_ID_UND 0xff
+int rtw89_fw_h2c_general_pkt(struct rtw89_dev *rtwdev, u8 macid)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_GENERAL_PKT_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_GENERAL_PKT_LEN);
+	SET_GENERAL_PKT_MACID(skb->data, macid);
+	SET_GENERAL_PKT_PROBRSP_ID(skb->data, H2C_GENERAL_PKT_ID_UND);
+	SET_GENERAL_PKT_PSPOLL_ID(skb->data, H2C_GENERAL_PKT_ID_UND);
+	SET_GENERAL_PKT_NULL_ID(skb->data, H2C_GENERAL_PKT_ID_UND);
+	SET_GENERAL_PKT_QOS_NULL_ID(skb->data, H2C_GENERAL_PKT_ID_UND);
+	SET_GENERAL_PKT_CTS2SELF_ID(skb->data, H2C_GENERAL_PKT_ID_UND);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_FW_INFO,
+			      H2C_FUNC_MAC_GENERAL_PKT, 0, 1,
+			      H2C_GENERAL_PKT_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_LPS_PARM_LEN 8
+int rtw89_fw_h2c_lps_parm(struct rtw89_dev *rtwdev,
+			  struct rtw89_lps_parm *lps_param)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_LPS_PARM_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_LPS_PARM_LEN);
+
+	SET_LPS_PARM_MACID(skb->data, lps_param->macid);
+	SET_LPS_PARM_PSMODE(skb->data, lps_param->psmode);
+	SET_LPS_PARM_LASTRPWM(skb->data, lps_param->lastrpwm);
+	SET_LPS_PARM_RLBM(skb->data, 1);
+	SET_LPS_PARM_SMARTPS(skb->data, 1);
+	SET_LPS_PARM_AWAKEINTERVAL(skb->data, 1);
+	SET_LPS_PARM_VOUAPSD(skb->data, 0);
+	SET_LPS_PARM_VIUAPSD(skb->data, 0);
+	SET_LPS_PARM_BEUAPSD(skb->data, 0);
+	SET_LPS_PARM_BKUAPSD(skb->data, 0);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC,
+			      H2C_CL_MAC_PS,
+			      H2C_FUNC_MAC_LPS_PARM, 0, 1,
+			      H2C_LPS_PARM_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_CMC_TBL_LEN 68
+int rtw89_fw_h2c_default_cmac_tbl(struct rtw89_dev *rtwdev, u8 macid)
+{
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct sk_buff *skb;
+	u8 ntx_path = hal->antenna_tx ? hal->antenna_tx : RF_B;
+	u8 map_b = hal->antenna_tx == RF_AB ? 1 : 0;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_CMC_TBL_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_CMC_TBL_LEN);
+	SET_CTRL_INFO_MACID(skb->data, macid);
+	SET_CTRL_INFO_OPERATION(skb->data, 1);
+	SET_CMC_TBL_TXPWR_MODE(skb->data, 0);
+	SET_CMC_TBL_NTX_PATH_EN(skb->data, ntx_path);
+	SET_CMC_TBL_PATH_MAP_A(skb->data, 0);
+	SET_CMC_TBL_PATH_MAP_B(skb->data, map_b);
+	SET_CMC_TBL_PATH_MAP_C(skb->data, 0);
+	SET_CMC_TBL_PATH_MAP_D(skb->data, 0);
+	SET_CMC_TBL_ANTSEL_A(skb->data, 0);
+	SET_CMC_TBL_ANTSEL_B(skb->data, 0);
+	SET_CMC_TBL_ANTSEL_C(skb->data, 0);
+	SET_CMC_TBL_ANTSEL_D(skb->data, 0);
+	SET_CMC_TBL_DOPPLER_CTRL(skb->data, 0);
+	SET_CMC_TBL_TXPWR_TOLERENCE(skb->data, 0);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_FR_EXCHG,
+			      H2C_FUNC_MAC_CCTLINFO_UD, 0, 1,
+			      H2C_CMC_TBL_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+static void __get_sta_he_pkt_padding(struct rtw89_dev *rtwdev,
+				     struct ieee80211_sta *sta, u8 *pads)
+{
+	bool ppe_th;
+	u8 ppe16, ppe8;
+	u8 nss = min(sta->rx_nss, rtwdev->hal.tx_nss) - 1;
+	u8 ppe_thres_hdr = sta->he_cap.ppe_thres[0];
+	u8 ru_bitmap;
+	u8 n, idx, sh;
+	u16 ppe;
+	int i;
+
+	if (!sta->he_cap.has_he)
+		return;
+
+	ppe_th = FIELD_GET(IEEE80211_HE_PHY_CAP6_PPE_THRESHOLD_PRESENT,
+			   sta->he_cap.he_cap_elem.phy_cap_info[6]);
+	if (!ppe_th) {
+		u8 pad;
+
+		pad = FIELD_GET(IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_MASK,
+				sta->he_cap.he_cap_elem.phy_cap_info[9]);
+
+		for (i = 0; i < RTW89_PPE_BW_NUM; i++)
+			pads[i] = pad;
+	}
+
+	ru_bitmap = FIELD_GET(IEEE80211_PPE_THRES_RU_INDEX_BITMASK_MASK, ppe_thres_hdr);
+	n = hweight8(ru_bitmap);
+	n = 7 + (n * IEEE80211_PPE_THRES_INFO_PPET_SIZE * 2) * nss;
+
+	for (i = 0; i < RTW89_PPE_BW_NUM; i++) {
+		if (!(ru_bitmap & BIT(i))) {
+			pads[i] = 1;
+			continue;
+		}
+
+		idx = n >> 3;
+		sh = n & 7;
+		n += IEEE80211_PPE_THRES_INFO_PPET_SIZE * 2;
+
+		ppe = le16_to_cpu(*((__le16 *)&sta->he_cap.ppe_thres[idx]));
+		ppe16 = (ppe >> sh) & IEEE80211_PPE_THRES_NSS_MASK;
+		sh += IEEE80211_PPE_THRES_INFO_PPET_SIZE;
+		ppe8 = (ppe >> sh) & IEEE80211_PPE_THRES_NSS_MASK;
+
+		if (ppe16 != 7 && ppe8 == 7)
+			pads[i] = 2;
+		else if (ppe8 != 7)
+			pads[i] = 1;
+		else
+			pads[i] = 0;
+	}
+}
+
+int rtw89_fw_h2c_assoc_cmac_tbl(struct rtw89_dev *rtwdev,
+				struct ieee80211_vif *vif,
+				struct ieee80211_sta *sta)
+{
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct sk_buff *skb;
+	u8 pads[RTW89_PPE_BW_NUM];
+
+	memset(pads, 0, sizeof(pads));
+	__get_sta_he_pkt_padding(rtwdev, sta, pads);
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_CMC_TBL_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_CMC_TBL_LEN);
+	SET_CTRL_INFO_MACID(skb->data, rtwsta->mac_id);
+	SET_CTRL_INFO_OPERATION(skb->data, 1);
+	SET_CMC_TBL_DISRTSFB(skb->data, 1);
+	SET_CMC_TBL_DISDATAFB(skb->data, 1);
+	if (hal->current_band_type == RTW89_BAND_2G)
+		SET_CMC_TBL_RTS_RTY_LOWEST_RATE(skb->data, RTW89_HW_RATE_CCK1);
+	else
+		SET_CMC_TBL_RTS_RTY_LOWEST_RATE(skb->data, RTW89_HW_RATE_OFDM6);
+	SET_CMC_TBL_RTS_TXCNT_LMT_SEL(skb->data, 0);
+	SET_CMC_TBL_DATA_TXCNT_LMT_SEL(skb->data, 0);
+	if (vif->type == NL80211_IFTYPE_STATION)
+		SET_CMC_TBL_ULDL(skb->data, 1);
+	else
+		SET_CMC_TBL_ULDL(skb->data, 0);
+	SET_CMC_TBL_MULTI_PORT_ID(skb->data, rtwvif->port);
+	SET_CMC_TBL_NOMINAL_PKT_PADDING(skb->data, pads[RTW89_CHANNEL_WIDTH_20]);
+	SET_CMC_TBL_NOMINAL_PKT_PADDING40(skb->data, pads[RTW89_CHANNEL_WIDTH_40]);
+	SET_CMC_TBL_NOMINAL_PKT_PADDING80(skb->data, pads[RTW89_CHANNEL_WIDTH_80]);
+	SET_CMC_TBL_BSR_QUEUE_SIZE_FORMAT(skb->data, sta->he_cap.has_he);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_FR_EXCHG,
+			      H2C_FUNC_MAC_CCTLINFO_UD, 0, 1,
+			      H2C_CMC_TBL_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+int rtw89_fw_h2c_txtime_cmac_tbl(struct rtw89_dev *rtwdev,
+				 struct rtw89_sta *rtwsta)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_CMC_TBL_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for fw dl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_CMC_TBL_LEN);
+	SET_CTRL_INFO_MACID(skb->data, rtwsta->mac_id);
+	SET_CTRL_INFO_OPERATION(skb->data, 1);
+	if (rtwsta->cctl_tx_time) {
+		SET_CMC_TBL_AMPDU_TIME_SEL(skb->data, 1);
+		SET_CMC_TBL_AMPDU_MAX_TIME(skb->data, rtwsta->ampdu_max_time);
+	}
+	if (rtwsta->cctl_tx_retry_limit) {
+		SET_CMC_TBL_DATA_TXCNT_LMT_SEL(skb->data, 1);
+		SET_CMC_TBL_DATA_TX_CNT_LMT(skb->data, rtwsta->data_tx_cnt_lmt);
+	}
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_FR_EXCHG,
+			      H2C_FUNC_MAC_CCTLINFO_UD, 0, 1,
+			      H2C_CMC_TBL_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_VIF_MAINTAIN_LEN 4
+int rtw89_fw_h2c_vif_maintain(struct rtw89_dev *rtwdev,
+			      struct rtw89_vif *rtwvif,
+			      enum rtw89_upd_mode upd_mode)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_VIF_MAINTAIN_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c join\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_VIF_MAINTAIN_LEN);
+	SET_FWROLE_MAINTAIN_MACID(skb->data, rtwvif->mac_id);
+	SET_FWROLE_MAINTAIN_SELF_ROLE(skb->data, rtwvif->self_role);
+	SET_FWROLE_MAINTAIN_UPD_MODE(skb->data, upd_mode);
+	SET_FWROLE_MAINTAIN_WIFI_ROLE(skb->data, rtwvif->wifi_role);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_MEDIA_RPT,
+			      H2C_FUNC_MAC_FWROLE_MAINTAIN, 0, 1,
+			      H2C_VIF_MAINTAIN_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_JOIN_INFO_LEN 4
+int rtw89_fw_h2c_join_info(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			   u8 dis_conn)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_JOIN_INFO_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c join\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_JOIN_INFO_LEN);
+	SET_JOININFO_MACID(skb->data, rtwvif->mac_id);
+	SET_JOININFO_OP(skb->data, dis_conn);
+	SET_JOININFO_BAND(skb->data, rtwvif->mac_idx);
+	SET_JOININFO_WMM(skb->data, rtwvif->wmm);
+	SET_JOININFO_TGR(skb->data, rtwvif->trigger);
+	SET_JOININFO_ISHESTA(skb->data, 0);
+	SET_JOININFO_DLBW(skb->data, 0);
+	SET_JOININFO_TF_MAC_PAD(skb->data, 0);
+	SET_JOININFO_DL_T_PE(skb->data, 0);
+	SET_JOININFO_PORT_ID(skb->data, rtwvif->port);
+	SET_JOININFO_NET_TYPE(skb->data, rtwvif->net_type);
+	SET_JOININFO_WIFI_ROLE(skb->data, rtwvif->wifi_role);
+	SET_JOININFO_SELF_ROLE(skb->data, rtwvif->self_role);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_MEDIA_RPT,
+			      H2C_FUNC_MAC_JOININFO, 0, 1,
+			      H2C_JOIN_INFO_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+int rtw89_fw_h2c_macid_pause(struct rtw89_dev *rtwdev, u8 sh, u8 grp,
+			     bool pause)
+{
+	struct rtw89_fw_macid_pause_grp h2c = {{0}};
+	u8 len = sizeof(struct rtw89_fw_macid_pause_grp);
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_JOIN_INFO_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c join\n");
+		return -ENOMEM;
+	}
+	h2c.mask_grp[grp] = cpu_to_le32(BIT(sh));
+	if (pause)
+		h2c.pause_grp[grp] = cpu_to_le32(BIT(sh));
+	skb_put_data(skb, &h2c, len);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_FW_OFLD,
+			      H2C_FUNC_MAC_MACID_PAUSE, 1, 0,
+			      len);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_EDCA_LEN 12
+int rtw89_fw_h2c_set_edca(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			  u8 ac, u32 val)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_EDCA_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c edca\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_EDCA_LEN);
+	RTW89_SET_EDCA_SEL(skb->data, 0);
+	RTW89_SET_EDCA_BAND(skb->data, rtwvif->mac_idx);
+	RTW89_SET_EDCA_WMM(skb->data, 0);
+	RTW89_SET_EDCA_AC(skb->data, ac);
+	RTW89_SET_EDCA_PARAM(skb->data, val);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_FW_OFLD,
+			      H2C_FUNC_USR_EDCA, 0, 1,
+			      H2C_EDCA_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_OFLD_CFG_LEN 8
+int rtw89_fw_h2c_set_ofld_cfg(struct rtw89_dev *rtwdev)
+{
+	static const u8 cfg[] = {0x09, 0x00, 0x00, 0x00, 0x5e, 0x00, 0x00, 0x00};
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_OFLD_CFG_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c ofld\n");
+		return -ENOMEM;
+	}
+	skb_put_data(skb, cfg, H2C_OFLD_CFG_LEN);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_MAC, H2C_CL_MAC_FW_OFLD,
+			      H2C_FUNC_OFLD_CFG, 0, 1,
+			      H2C_OFLD_CFG_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_RA_LEN 16
+int rtw89_fw_h2c_ra(struct rtw89_dev *rtwdev, struct rtw89_ra_info *ra, bool csi)
+{
+	struct sk_buff *skb;
+	u8 *cmd;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_RA_LEN);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c join\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_RA_LEN);
+	cmd = skb->data;
+	rtw89_debug(rtwdev, RTW89_DBG_RA,
+		    "ra cmd msk: %llx ", ra->ra_mask);
+
+	RTW89_SET_FWCMD_RA_MODE(cmd, ra->mode_ctrl);
+	RTW89_SET_FWCMD_RA_BW_CAP(cmd, ra->bw_cap);
+	RTW89_SET_FWCMD_RA_MACID(cmd, ra->macid);
+	RTW89_SET_FWCMD_RA_DCM(cmd, ra->dcm_cap);
+	RTW89_SET_FWCMD_RA_ER(cmd, ra->er_cap);
+	RTW89_SET_FWCMD_RA_INIT_RATE_LV(cmd, ra->init_rate_lv);
+	RTW89_SET_FWCMD_RA_UPD_ALL(cmd, ra->upd_all);
+	RTW89_SET_FWCMD_RA_SGI(cmd, ra->en_sgi);
+	RTW89_SET_FWCMD_RA_LDPC(cmd, ra->ldpc_cap);
+	RTW89_SET_FWCMD_RA_STBC(cmd, ra->stbc_cap);
+	RTW89_SET_FWCMD_RA_SS_NUM(cmd, ra->ss_num);
+	RTW89_SET_FWCMD_RA_GILTF(cmd, ra->giltf);
+	RTW89_SET_FWCMD_RA_UPD_BW_NSS_MASK(cmd, ra->upd_bw_nss_mask);
+	RTW89_SET_FWCMD_RA_UPD_MASK(cmd, ra->upd_mask);
+	RTW89_SET_FWCMD_RA_MASK_0(cmd, FIELD_GET(MASKBYTE0, ra->ra_mask));
+	RTW89_SET_FWCMD_RA_MASK_1(cmd, FIELD_GET(MASKBYTE1, ra->ra_mask));
+	RTW89_SET_FWCMD_RA_MASK_2(cmd, FIELD_GET(MASKBYTE2, ra->ra_mask));
+	RTW89_SET_FWCMD_RA_MASK_3(cmd, FIELD_GET(MASKBYTE3, ra->ra_mask));
+	RTW89_SET_FWCMD_RA_MASK_4(cmd, FIELD_GET(MASKBYTE4, ra->ra_mask));
+
+	if (csi) {
+		RTW89_SET_FWCMD_RA_BFEE_CSI_CTL(cmd, 1);
+		RTW89_SET_FWCMD_RA_BAND_NUM(cmd, ra->band_num);
+		RTW89_SET_FWCMD_RA_CR_TBL_SEL(cmd, ra->cr_tbl_sel);
+		RTW89_SET_FWCMD_RA_FIXED_CSI_RATE_EN(cmd, ra->fixed_csi_rate_en);
+		RTW89_SET_FWCMD_RA_RA_CSI_RATE_EN(cmd, ra->ra_csi_rate_en);
+		RTW89_SET_FWCMD_RA_FIXED_CSI_MCS_SS_IDX(cmd, ra->csi_mcs_ss_idx);
+		RTW89_SET_FWCMD_RA_FIXED_CSI_MODE(cmd, ra->csi_mode);
+		RTW89_SET_FWCMD_RA_FIXED_CSI_GI_LTF(cmd, ra->csi_gi_ltf);
+		RTW89_SET_FWCMD_RA_FIXED_CSI_BW(cmd, ra->csi_bw);
+	}
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, H2C_CL_OUTSRC_RA,
+			      H2C_FUNC_OUTSRC_RA_MACIDCFG, 0, 0,
+			      H2C_RA_LEN);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_LEN_CXDRVHDR 2
+#define H2C_LEN_CXDRVINFO_INIT (12 + H2C_LEN_CXDRVHDR)
+int rtw89_fw_h2c_cxdrv_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_init_info *init_info = &dm->init_info;
+	struct rtw89_btc_module *module = &init_info->module;
+	struct rtw89_btc_ant_info *ant = &module->ant;
+	struct sk_buff *skb;
+	u8 *cmd;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_LEN_CXDRVINFO_INIT);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c cxdrv_init\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_LEN_CXDRVINFO_INIT);
+	cmd = skb->data;
+
+	RTW89_SET_FWCMD_CXHDR_TYPE(cmd, CXDRVINFO_INIT);
+	RTW89_SET_FWCMD_CXHDR_LEN(cmd, H2C_LEN_CXDRVINFO_INIT - H2C_LEN_CXDRVHDR);
+
+	RTW89_SET_FWCMD_CXINIT_ANT_TYPE(cmd, ant->type);
+	RTW89_SET_FWCMD_CXINIT_ANT_NUM(cmd, ant->num);
+	RTW89_SET_FWCMD_CXINIT_ANT_ISO(cmd, ant->isolation);
+	RTW89_SET_FWCMD_CXINIT_ANT_POS(cmd, ant->single_pos);
+	RTW89_SET_FWCMD_CXINIT_ANT_DIVERSITY(cmd, ant->diversity);
+
+	RTW89_SET_FWCMD_CXINIT_MOD_RFE(cmd, module->rfe_type);
+	RTW89_SET_FWCMD_CXINIT_MOD_CV(cmd, module->cv);
+	RTW89_SET_FWCMD_CXINIT_MOD_BT_SOLO(cmd, module->bt_solo);
+	RTW89_SET_FWCMD_CXINIT_MOD_BT_POS(cmd, module->bt_pos);
+	RTW89_SET_FWCMD_CXINIT_MOD_SW_TYPE(cmd, module->switch_type);
+
+	RTW89_SET_FWCMD_CXINIT_WL_GCH(cmd, init_info->wl_guard_ch);
+	RTW89_SET_FWCMD_CXINIT_WL_ONLY(cmd, init_info->wl_only);
+	RTW89_SET_FWCMD_CXINIT_WL_INITOK(cmd, init_info->wl_init_ok);
+	RTW89_SET_FWCMD_CXINIT_DBCC_EN(cmd, init_info->dbcc_en);
+	RTW89_SET_FWCMD_CXINIT_CX_OTHER(cmd, init_info->cx_other);
+	RTW89_SET_FWCMD_CXINIT_BT_ONLY(cmd, init_info->bt_only);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, BTFC_SET,
+			      SET_DRV_INFO, 0, 0,
+			      H2C_LEN_CXDRVINFO_INIT);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_LEN_CXDRVINFO_ROLE (4 + 12 * RTW89_MAX_HW_PORT_NUM + H2C_LEN_CXDRVHDR)
+int rtw89_fw_h2c_cxdrv_role(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_role_info *role_info = &wl->role_info;
+	struct rtw89_btc_wl_role_info_bpos *bpos = &role_info->role_map.role;
+	struct rtw89_btc_wl_active_role *active = role_info->active_role;
+	struct sk_buff *skb;
+	u8 *cmd;
+	int i;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_LEN_CXDRVINFO_ROLE);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c cxdrv_role\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_LEN_CXDRVINFO_ROLE);
+	cmd = skb->data;
+
+	RTW89_SET_FWCMD_CXHDR_TYPE(cmd, CXDRVINFO_ROLE);
+	RTW89_SET_FWCMD_CXHDR_LEN(cmd, H2C_LEN_CXDRVINFO_ROLE - H2C_LEN_CXDRVHDR);
+
+	RTW89_SET_FWCMD_CXROLE_CONNECT_CNT(cmd, role_info->connect_cnt);
+	RTW89_SET_FWCMD_CXROLE_LINK_MODE(cmd, role_info->link_mode);
+
+	RTW89_SET_FWCMD_CXROLE_ROLE_NONE(cmd, bpos->none);
+	RTW89_SET_FWCMD_CXROLE_ROLE_STA(cmd, bpos->station);
+	RTW89_SET_FWCMD_CXROLE_ROLE_AP(cmd, bpos->ap);
+	RTW89_SET_FWCMD_CXROLE_ROLE_VAP(cmd, bpos->vap);
+	RTW89_SET_FWCMD_CXROLE_ROLE_ADHOC(cmd, bpos->adhoc);
+	RTW89_SET_FWCMD_CXROLE_ROLE_ADHOC_MASTER(cmd, bpos->adhoc_master);
+	RTW89_SET_FWCMD_CXROLE_ROLE_MESH(cmd, bpos->mesh);
+	RTW89_SET_FWCMD_CXROLE_ROLE_MONITOR(cmd, bpos->moniter);
+	RTW89_SET_FWCMD_CXROLE_ROLE_P2P_DEV(cmd, bpos->p2p_device);
+	RTW89_SET_FWCMD_CXROLE_ROLE_P2P_GC(cmd, bpos->p2p_gc);
+	RTW89_SET_FWCMD_CXROLE_ROLE_P2P_GO(cmd, bpos->p2p_go);
+	RTW89_SET_FWCMD_CXROLE_ROLE_NAN(cmd, bpos->nan);
+
+	for (i = 0; i < RTW89_MAX_HW_PORT_NUM; i++, active++) {
+		RTW89_SET_FWCMD_CXROLE_ACT_CONNECTED(cmd, active->connected, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_PID(cmd, active->pid, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_PHY(cmd, active->phy, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_NOA(cmd, active->noa, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_BAND(cmd, active->band, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_CLIENT_PS(cmd, active->client_ps, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_BW(cmd, active->bw, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_ROLE(cmd, active->role, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_CH(cmd, active->ch, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_TX_LVL(cmd, active->tx_lvl, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_RX_LVL(cmd, active->rx_lvl, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_TX_RATE(cmd, active->tx_rate, i);
+		RTW89_SET_FWCMD_CXROLE_ACT_RX_RATE(cmd, active->rx_rate, i);
+	}
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, BTFC_SET,
+			      SET_DRV_INFO, 0, 0,
+			      H2C_LEN_CXDRVINFO_ROLE);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_LEN_CXDRVINFO_CTRL (4 + H2C_LEN_CXDRVHDR)
+int rtw89_fw_h2c_cxdrv_ctrl(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_ctrl *ctrl = &btc->ctrl;
+	struct sk_buff *skb;
+	u8 *cmd;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_LEN_CXDRVINFO_CTRL);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c cxdrv_ctrl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_LEN_CXDRVINFO_CTRL);
+	cmd = skb->data;
+
+	RTW89_SET_FWCMD_CXHDR_TYPE(cmd, CXDRVINFO_CTRL);
+	RTW89_SET_FWCMD_CXHDR_LEN(cmd, H2C_LEN_CXDRVINFO_CTRL - H2C_LEN_CXDRVHDR);
+
+	RTW89_SET_FWCMD_CXCTRL_MANUAL(cmd, ctrl->manual);
+	RTW89_SET_FWCMD_CXCTRL_IGNORE_BT(cmd, ctrl->igno_bt);
+	RTW89_SET_FWCMD_CXCTRL_ALWAYS_FREERUN(cmd, ctrl->always_freerun);
+	RTW89_SET_FWCMD_CXCTRL_TRACE_STEP(cmd, ctrl->trace_step);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, BTFC_SET,
+			      SET_DRV_INFO, 0, 0,
+			      H2C_LEN_CXDRVINFO_CTRL);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+#define H2C_LEN_CXDRVINFO_RFK (4 + H2C_LEN_CXDRVHDR)
+int rtw89_fw_h2c_cxdrv_rfk(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_wl_info *wl = &btc->cx.wl;
+	struct rtw89_btc_wl_rfk_info *rfk_info = &wl->rfk_info;
+	struct sk_buff *skb;
+	u8 *cmd;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(H2C_LEN_CXDRVINFO_RFK);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c cxdrv_ctrl\n");
+		return -ENOMEM;
+	}
+	skb_put(skb, H2C_LEN_CXDRVINFO_RFK);
+	cmd = skb->data;
+
+	RTW89_SET_FWCMD_CXHDR_TYPE(cmd, CXDRVINFO_RFK);
+	RTW89_SET_FWCMD_CXHDR_LEN(cmd, H2C_LEN_CXDRVINFO_RFK - H2C_LEN_CXDRVHDR);
+
+	RTW89_SET_FWCMD_CXRFK_STATE(cmd, rfk_info->state);
+	RTW89_SET_FWCMD_CXRFK_PATH_MAP(cmd, rfk_info->path_map);
+	RTW89_SET_FWCMD_CXRFK_PHY_MAP(cmd, rfk_info->phy_map);
+	RTW89_SET_FWCMD_CXRFK_BAND(cmd, rfk_info->band);
+	RTW89_SET_FWCMD_CXRFK_TYPE(cmd, rfk_info->type);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, BTFC_SET,
+			      SET_DRV_INFO, 0, 0,
+			      H2C_LEN_CXDRVINFO_RFK);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+int rtw89_fw_h2c_rf_reg(struct rtw89_dev *rtwdev,
+			struct rtw89_fw_h2c_rf_reg_info *info,
+			u16 len, u8 page)
+{
+	struct sk_buff *skb;
+	u8 class = info->rf_path == RF_PATH_A ?
+		   H2C_CL_OUTSRC_RF_REG_A : H2C_CL_OUTSRC_RF_REG_B;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(len);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c rf reg\n");
+		return -ENOMEM;
+	}
+	skb_put_data(skb, info->rtw89_phy_config_rf_h2c[page], len);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, class, page, 0, 0,
+			      len);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+int rtw89_fw_h2c_raw_with_hdr(struct rtw89_dev *rtwdev,
+			      u8 h2c_class, u8 h2c_func, u8 *buf, u16 len,
+			      bool rack, bool dack)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_with_hdr(len);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for raw with hdr\n");
+		return -ENOMEM;
+	}
+	skb_put_data(skb, buf, len);
+
+	rtw89_h2c_pkt_set_hdr(rtwdev, skb, FWCMD_TYPE_H2C,
+			      H2C_CAT_OUTSRC, h2c_class, h2c_func, rack, dack,
+			      len);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+int rtw89_fw_h2c_raw(struct rtw89_dev *rtwdev, const u8 *buf, u16 len)
+{
+	struct sk_buff *skb;
+
+	skb = rtw89_fw_h2c_alloc_skb_no_hdr(len);
+	if (!skb) {
+		rtw89_err(rtwdev, "failed to alloc skb for h2c raw\n");
+		return -ENOMEM;
+	}
+	skb_put_data(skb, buf, len);
+
+	if (rtw89_h2c_tx(rtwdev, skb, false)) {
+		rtw89_err(rtwdev, "failed to send h2c\n");
+		goto fail;
+	}
+
+	return 0;
+fail:
+	dev_kfree_skb_any(skb);
+
+	return -EBUSY;
+}
+
+void rtw89_fw_send_all_early_h2c(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_early_h2c *early_h2c;
+
+	lockdep_assert_held(&rtwdev->mutex);
+
+	list_for_each_entry(early_h2c, &rtwdev->early_h2c_list, list) {
+		rtw89_fw_h2c_raw(rtwdev, early_h2c->h2c, early_h2c->h2c_len);
+	}
+}
+
+void rtw89_fw_free_all_early_h2c(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_early_h2c *early_h2c, *tmp;
+
+	mutex_lock(&rtwdev->mutex);
+	list_for_each_entry_safe(early_h2c, tmp, &rtwdev->early_h2c_list, list) {
+		list_del(&early_h2c->list);
+		kfree(early_h2c->h2c);
+		kfree(early_h2c);
+	}
+	mutex_unlock(&rtwdev->mutex);
+}
+
+void rtw89_fw_c2h_irqsafe(struct rtw89_dev *rtwdev, struct sk_buff *c2h)
+{
+	skb_queue_tail(&rtwdev->c2h_queue, c2h);
+	ieee80211_queue_work(rtwdev->hw, &rtwdev->c2h_work);
+}
+
+static void rtw89_fw_c2h_cmd_handle(struct rtw89_dev *rtwdev,
+				    struct sk_buff *skb)
+{
+	u8 category = RTW89_GET_C2H_CATEGORY(skb->data);
+	u8 class = RTW89_GET_C2H_CLASS(skb->data);
+	u8 func = RTW89_GET_C2H_FUNC(skb->data);
+	u16 len = RTW89_GET_C2H_LEN(skb->data);
+	bool dump = true;
+
+	if (!test_bit(RTW89_FLAG_RUNNING, rtwdev->flags))
+		return;
+
+	switch (category) {
+	case RTW89_C2H_CAT_TEST:
+		break;
+	case RTW89_C2H_CAT_MAC:
+		rtw89_mac_c2h_handle(rtwdev, skb, len, class, func);
+		if (class == RTW89_MAC_C2H_CLASS_INFO &&
+		    func == RTW89_MAC_C2H_FUNC_C2H_LOG)
+			dump = false;
+		break;
+	case RTW89_C2H_CAT_OUTSRC:
+		if (class >= RTW89_PHY_C2H_CLASS_BTC_MIN &&
+		    class <= RTW89_PHY_C2H_CLASS_BTC_MAX)
+			rtw89_btc_c2h_handle(rtwdev, skb, len, class, func);
+		else
+			rtw89_phy_c2h_handle(rtwdev, skb, len, class, func);
+		break;
+	}
+
+	if (dump)
+		rtw89_hex_dump(rtwdev, RTW89_DBG_FW, "C2H: ", skb->data, skb->len);
+}
+
+void rtw89_fw_c2h_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						c2h_work);
+	struct sk_buff *skb, *tmp;
+
+	skb_queue_walk_safe(&rtwdev->c2h_queue, skb, tmp) {
+		skb_unlink(skb, &rtwdev->c2h_queue);
+		mutex_lock(&rtwdev->mutex);
+		rtw89_fw_c2h_cmd_handle(rtwdev, skb);
+		mutex_unlock(&rtwdev->mutex);
+		dev_kfree_skb_any(skb);
+	}
+}
+
+static int rtw89_fw_write_h2c_reg(struct rtw89_dev *rtwdev,
+				  struct rtw89_mac_h2c_info *info)
+{
+	static const u32 h2c_reg[RTW89_H2CREG_MAX] = {
+		R_AX_H2CREG_DATA0, R_AX_H2CREG_DATA1,
+		R_AX_H2CREG_DATA2, R_AX_H2CREG_DATA3
+	};
+	u8 i, val, len;
+	int ret;
+
+	ret = read_poll_timeout(rtw89_read8, val, val == 0, 1000, 5000, false,
+				rtwdev, R_AX_H2CREG_CTRL);
+	if (ret) {
+		rtw89_warn(rtwdev, "FW does not process h2c registers\n");
+		return ret;
+	}
+
+	len = DIV_ROUND_UP(info->content_len + RTW89_H2CREG_HDR_LEN,
+			   sizeof(info->h2creg[0]));
+
+	RTW89_SET_H2CREG_HDR_FUNC(&info->h2creg[0], info->id);
+	RTW89_SET_H2CREG_HDR_LEN(&info->h2creg[0], len);
+	for (i = 0; i < RTW89_H2CREG_MAX; i++)
+		rtw89_write32(rtwdev, h2c_reg[i], info->h2creg[i]);
+
+	rtw89_write8(rtwdev, R_AX_H2CREG_CTRL, B_AX_H2CREG_TRIGGER);
+
+	return 0;
+}
+
+static int rtw89_fw_read_c2h_reg(struct rtw89_dev *rtwdev,
+				 struct rtw89_mac_c2h_info *info)
+{
+	static const u32 c2h_reg[RTW89_C2HREG_MAX] = {
+		R_AX_C2HREG_DATA0, R_AX_C2HREG_DATA1,
+		R_AX_C2HREG_DATA2, R_AX_C2HREG_DATA3
+	};
+	u32 ret;
+	u8 i, val;
+
+	info->id = RTW89_FWCMD_C2HREG_FUNC_NULL;
+
+	ret = read_poll_timeout_atomic(rtw89_read8, val, val, 1,
+				       RTW89_C2H_TIMEOUT, false, rtwdev,
+				       R_AX_C2HREG_CTRL);
+	if (ret) {
+		rtw89_warn(rtwdev, "c2h reg timeout\n");
+		return ret;
+	}
+
+	for (i = 0; i < RTW89_C2HREG_MAX; i++)
+		info->c2hreg[i] = rtw89_read32(rtwdev, c2h_reg[i]);
+
+	rtw89_write8(rtwdev, R_AX_C2HREG_CTRL, 0);
+
+	info->id = RTW89_GET_C2H_HDR_FUNC(*info->c2hreg);
+	info->content_len = (RTW89_GET_C2H_HDR_LEN(*info->c2hreg) << 2) -
+				RTW89_C2HREG_HDR_LEN;
+
+	return 0;
+}
+
+int rtw89_fw_msg_reg(struct rtw89_dev *rtwdev,
+		     struct rtw89_mac_h2c_info *h2c_info,
+		     struct rtw89_mac_c2h_info *c2h_info)
+{
+	u32 ret;
+
+	if (h2c_info && h2c_info->id != RTW89_FWCMD_H2CREG_FUNC_GET_FEATURE)
+		lockdep_assert_held(&rtwdev->mutex);
+
+	if (!h2c_info && !c2h_info)
+		return -EINVAL;
+
+	if (!h2c_info)
+		goto recv_c2h;
+
+	ret = rtw89_fw_write_h2c_reg(rtwdev, h2c_info);
+	if (ret)
+		return ret;
+
+recv_c2h:
+	if (!c2h_info)
+		return 0;
+
+	ret = rtw89_fw_read_c2h_reg(rtwdev, c2h_info);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+void rtw89_fw_st_dbg_dump(struct rtw89_dev *rtwdev)
+{
+	if (!test_bit(RTW89_FLAG_POWERON, rtwdev->flags)) {
+		rtw89_err(rtwdev, "[ERR]pwr is off\n");
+		return;
+	}
+
+	rtw89_info(rtwdev, "FW status = 0x%x\n", rtw89_read32(rtwdev, R_AX_UDM0));
+	rtw89_info(rtwdev, "FW BADADDR = 0x%x\n", rtw89_read32(rtwdev, R_AX_UDM1));
+	rtw89_info(rtwdev, "FW EPC/RA = 0x%x\n", rtw89_read32(rtwdev, R_AX_UDM2));
+	rtw89_info(rtwdev, "FW MISC = 0x%x\n", rtw89_read32(rtwdev, R_AX_UDM3));
+	rtw89_info(rtwdev, "R_AX_HALT_C2H = 0x%x\n",
+		   rtw89_read32(rtwdev, R_AX_HALT_C2H));
+	rtw89_info(rtwdev, "R_AX_SER_DBG_INFO = 0x%x\n",
+		   rtw89_read32(rtwdev, R_AX_SER_DBG_INFO));
+
+	rtw89_fw_prog_cnt_dump(rtwdev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/fw.h
@@ -0,0 +1,1378 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_FW_H__
+#define __RTW89_FW_H__
+
+#include "core.h"
+
+enum rtw89_fw_dl_status {
+	RTW89_FWDL_INITIAL_STATE = 0,
+	RTW89_FWDL_FWDL_ONGOING = 1,
+	RTW89_FWDL_CHECKSUM_FAIL = 2,
+	RTW89_FWDL_SECURITY_FAIL = 3,
+	RTW89_FWDL_CV_NOT_MATCH = 4,
+	RTW89_FWDL_RSVD0 = 5,
+	RTW89_FWDL_WCPU_FWDL_RDY = 6,
+	RTW89_FWDL_WCPU_FW_INIT_RDY = 7
+};
+
+#define RTW89_GET_C2H_HDR_FUNC(info) \
+	u32_get_bits(info, GENMASK(6, 0))
+#define RTW89_GET_C2H_HDR_LEN(info) \
+	u32_get_bits(info, GENMASK(11, 8))
+
+#define RTW89_SET_H2CREG_HDR_FUNC(info, val) \
+	u32p_replace_bits(info, val, GENMASK(6, 0))
+#define RTW89_SET_H2CREG_HDR_LEN(info, val) \
+	u32p_replace_bits(info, val, GENMASK(11, 8))
+
+#define RTW89_H2CREG_MAX 4
+#define RTW89_C2HREG_MAX 4
+#define RTW89_C2HREG_HDR_LEN 2
+#define RTW89_H2CREG_HDR_LEN 2
+#define RTW89_C2H_TIMEOUT 1000000
+struct rtw89_mac_c2h_info {
+	u8 id;
+	u8 content_len;
+	u32 c2hreg[RTW89_C2HREG_MAX];
+};
+
+struct rtw89_mac_h2c_info {
+	u8 id;
+	u8 content_len;
+	u32 h2creg[RTW89_H2CREG_MAX];
+};
+
+enum rtw89_mac_h2c_type {
+	RTW89_FWCMD_H2CREG_FUNC_H2CREG_LB = 0,
+	RTW89_FWCMD_H2CREG_FUNC_CNSL_CMD,
+	RTW89_FWCMD_H2CREG_FUNC_FWERR,
+	RTW89_FWCMD_H2CREG_FUNC_GET_FEATURE,
+	RTW89_FWCMD_H2CREG_FUNC_GETPKT_INFORM,
+	RTW89_FWCMD_H2CREG_FUNC_SCH_TX_EN
+};
+
+enum rtw89_mac_c2h_type {
+	RTW89_FWCMD_C2HREG_FUNC_C2HREG_LB = 0,
+	RTW89_FWCMD_C2HREG_FUNC_ERR_RPT,
+	RTW89_FWCMD_C2HREG_FUNC_ERR_MSG,
+	RTW89_FWCMD_C2HREG_FUNC_PHY_CAP,
+	RTW89_FWCMD_C2HREG_FUNC_TX_PAUSE_RPT,
+	RTW89_FWCMD_C2HREG_FUNC_NULL = 0xFF
+};
+
+struct rtw89_c2h_phy_cap {
+	u32 func:7;
+	u32 ack:1;
+	u32 len:4;
+	u32 seq:4;
+	u32 rx_nss:8;
+	u32 bw:8;
+
+	u32 tx_nss:8;
+	u32 prot:8;
+	u32 nic:8;
+	u32 wl_func:8;
+
+	u32 hw_type:8;
+} __packed;
+
+enum rtw89_fw_c2h_category {
+	RTW89_C2H_CAT_TEST,
+	RTW89_C2H_CAT_MAC,
+	RTW89_C2H_CAT_OUTSRC,
+};
+
+enum rtw89_fw_log_level {
+	RTW89_FW_LOG_LEVEL_OFF,
+	RTW89_FW_LOG_LEVEL_CRT,
+	RTW89_FW_LOG_LEVEL_SER,
+	RTW89_FW_LOG_LEVEL_WARN,
+	RTW89_FW_LOG_LEVEL_LOUD,
+	RTW89_FW_LOG_LEVEL_TR,
+};
+
+enum rtw89_fw_log_path {
+	RTW89_FW_LOG_LEVEL_UART,
+	RTW89_FW_LOG_LEVEL_C2H,
+	RTW89_FW_LOG_LEVEL_SNI,
+};
+
+enum rtw89_fw_log_comp {
+	RTW89_FW_LOG_COMP_VER,
+	RTW89_FW_LOG_COMP_INIT,
+	RTW89_FW_LOG_COMP_TASK,
+	RTW89_FW_LOG_COMP_CNS,
+	RTW89_FW_LOG_COMP_H2C,
+	RTW89_FW_LOG_COMP_C2H,
+	RTW89_FW_LOG_COMP_TX,
+	RTW89_FW_LOG_COMP_RX,
+	RTW89_FW_LOG_COMP_IPSEC,
+	RTW89_FW_LOG_COMP_TIMER,
+	RTW89_FW_LOG_COMP_DBGPKT,
+	RTW89_FW_LOG_COMP_PS,
+	RTW89_FW_LOG_COMP_ERROR,
+	RTW89_FW_LOG_COMP_WOWLAN,
+	RTW89_FW_LOG_COMP_SECURE_BOOT,
+	RTW89_FW_LOG_COMP_BTC,
+	RTW89_FW_LOG_COMP_BB,
+	RTW89_FW_LOG_COMP_TWT,
+	RTW89_FW_LOG_COMP_RF,
+	RTW89_FW_LOG_COMP_MCC = 20,
+};
+
+#define FWDL_SECTION_MAX_NUM 10
+#define FWDL_SECTION_CHKSUM_LEN	8
+#define FWDL_SECTION_PER_PKT_LEN 2020
+
+struct rtw89_fw_hdr_section_info {
+	u8 redl;
+	const u8 *addr;
+	u32 len;
+	u32 dladdr;
+};
+
+struct rtw89_fw_bin_info {
+	u8 section_num;
+	u32 hdr_len;
+	struct rtw89_fw_hdr_section_info section_info[FWDL_SECTION_MAX_NUM];
+};
+
+struct rtw89_fw_macid_pause_grp {
+	__le32 pause_grp[4];
+	__le32 mask_grp[4];
+} __packed;
+
+struct rtw89_h2creg_sch_tx_en {
+	u8 func:7;
+	u8 ack:1;
+	u8 total_len:4;
+	u8 seq_num:4;
+	u16 tx_en:16;
+	u16 mask:16;
+	u8 band:1;
+	u16 rsvd:15;
+} __packed;
+
+#define RTW89_SET_FWCMD_RA_IS_DIS(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(0))
+#define RTW89_SET_FWCMD_RA_MODE(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(5, 1))
+#define RTW89_SET_FWCMD_RA_BW_CAP(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(7, 6))
+#define RTW89_SET_FWCMD_RA_MACID(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(15, 8))
+#define RTW89_SET_FWCMD_RA_DCM(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(16))
+#define RTW89_SET_FWCMD_RA_ER(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(17))
+#define RTW89_SET_FWCMD_RA_INIT_RATE_LV(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(19, 18))
+#define RTW89_SET_FWCMD_RA_UPD_ALL(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(20))
+#define RTW89_SET_FWCMD_RA_SGI(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(21))
+#define RTW89_SET_FWCMD_RA_LDPC(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(22))
+#define RTW89_SET_FWCMD_RA_STBC(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(23))
+#define RTW89_SET_FWCMD_RA_SS_NUM(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(26, 24))
+#define RTW89_SET_FWCMD_RA_GILTF(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(29, 27))
+#define RTW89_SET_FWCMD_RA_UPD_BW_NSS_MASK(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(30))
+#define RTW89_SET_FWCMD_RA_UPD_MASK(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(31))
+#define RTW89_SET_FWCMD_RA_MASK_0(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_RA_MASK_1(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, GENMASK(15, 8))
+#define RTW89_SET_FWCMD_RA_MASK_2(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, GENMASK(23, 16))
+#define RTW89_SET_FWCMD_RA_MASK_3(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, GENMASK(31, 24))
+#define RTW89_SET_FWCMD_RA_MASK_4(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x02, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_RA_BFEE_CSI_CTL(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x02, val, BIT(31))
+#define RTW89_SET_FWCMD_RA_BAND_NUM(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_RA_RA_CSI_RATE_EN(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, BIT(8))
+#define RTW89_SET_FWCMD_RA_FIXED_CSI_RATE_EN(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, BIT(9))
+#define RTW89_SET_FWCMD_RA_CR_TBL_SEL(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, BIT(10))
+#define RTW89_SET_FWCMD_RA_FIXED_CSI_MCS_SS_IDX(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, GENMASK(23, 16))
+#define RTW89_SET_FWCMD_RA_FIXED_CSI_MODE(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, GENMASK(25, 24))
+#define RTW89_SET_FWCMD_RA_FIXED_CSI_GI_LTF(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, GENMASK(28, 26))
+#define RTW89_SET_FWCMD_RA_FIXED_CSI_BW(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, GENMASK(31, 29))
+
+#define RTW89_SET_FWCMD_SEC_IDX(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_SEC_OFFSET(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(15, 8))
+#define RTW89_SET_FWCMD_SEC_LEN(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(23, 16))
+#define RTW89_SET_FWCMD_SEC_TYPE(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, GENMASK(3, 0))
+#define RTW89_SET_FWCMD_SEC_EXT_KEY(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, BIT(4))
+#define RTW89_SET_FWCMD_SEC_SPP_MODE(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, BIT(5))
+#define RTW89_SET_FWCMD_SEC_KEY0(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x02, val, GENMASK(31, 0))
+#define RTW89_SET_FWCMD_SEC_KEY1(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x03, val, GENMASK(31, 0))
+#define RTW89_SET_FWCMD_SEC_KEY2(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x04, val, GENMASK(31, 0))
+#define RTW89_SET_FWCMD_SEC_KEY3(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x05, val, GENMASK(31, 0))
+
+#define RTW89_SET_EDCA_SEL(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(1, 0))
+#define RTW89_SET_EDCA_BAND(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(3))
+#define RTW89_SET_EDCA_WMM(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, BIT(4))
+#define RTW89_SET_EDCA_AC(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x00, val, GENMASK(6, 5))
+#define RTW89_SET_EDCA_PARAM(cmd, val) \
+	le32p_replace_bits((__le32 *)(cmd) + 0x01, val, GENMASK(31, 0))
+#define FW_EDCA_PARAM_TXOPLMT_MSK GENMASK(26, 16)
+#define FW_EDCA_PARAM_CWMAX_MSK GENMASK(15, 12)
+#define FW_EDCA_PARAM_CWMIN_MSK GENMASK(11, 8)
+#define FW_EDCA_PARAM_AIFS_MSK GENMASK(7, 0)
+
+#define GET_FWSECTION_HDR_SEC_SIZE(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), GENMASK(23, 0))
+#define GET_FWSECTION_HDR_CHECKSUM(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), BIT(28))
+#define GET_FWSECTION_HDR_REDL(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), BIT(29))
+#define GET_FWSECTION_HDR_DL_ADDR(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr)), GENMASK(31, 0))
+
+#define GET_FW_HDR_MAJOR_VERSION(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), GENMASK(7, 0))
+#define GET_FW_HDR_MINOR_VERSION(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), GENMASK(15, 8))
+#define GET_FW_HDR_SUBVERSION(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), GENMASK(23, 16))
+#define GET_FW_HDR_SUBINDEX(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 1), GENMASK(31, 24))
+#define GET_FW_HDR_MONTH(fwhdr)		\
+	le32_get_bits(*((__le32 *)(fwhdr) + 4), GENMASK(7, 0))
+#define GET_FW_HDR_DATE(fwhdr)		\
+	le32_get_bits(*((__le32 *)(fwhdr) + 4), GENMASK(15, 8))
+#define GET_FW_HDR_HOUR(fwhdr)		\
+	le32_get_bits(*((__le32 *)(fwhdr) + 4), GENMASK(23, 16))
+#define GET_FW_HDR_MIN(fwhdr)		\
+	le32_get_bits(*((__le32 *)(fwhdr) + 4), GENMASK(31, 24))
+#define GET_FW_HDR_YEAR(fwhdr)		\
+	le32_get_bits(*((__le32 *)(fwhdr) + 5), GENMASK(31, 0))
+#define GET_FW_HDR_SEC_NUM(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 6), GENMASK(15, 8))
+#define GET_FW_HDR_CMD_VERSERION(fwhdr)	\
+	le32_get_bits(*((__le32 *)(fwhdr) + 7), GENMASK(31, 24))
+#define SET_FW_HDR_PART_SIZE(fwhdr, val)	\
+	le32p_replace_bits((__le32 *)(fwhdr) + 7, val, GENMASK(15, 0))
+
+#define SET_CTRL_INFO_MACID(table, val) \
+	le32p_replace_bits((__le32 *)(table) + 0, val, GENMASK(6, 0))
+#define SET_CTRL_INFO_OPERATION(table, val) \
+	le32p_replace_bits((__le32 *)(table) + 0, val, BIT(7))
+#define SET_CMC_TBL_MASK_DATARATE GENMASK(8, 0)
+#define SET_CMC_TBL_DATARATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, GENMASK(8, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_DATARATE, \
+			   GENMASK(8, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_FORCE_TXOP BIT(0)
+#define SET_CMC_TBL_FORCE_TXOP(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(9)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_FORCE_TXOP, \
+			   BIT(9)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_BW GENMASK(1, 0)
+#define SET_CMC_TBL_DATA_BW(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, GENMASK(11, 10)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_DATA_BW, \
+			   GENMASK(11, 10)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_GI_LTF GENMASK(2, 0)
+#define SET_CMC_TBL_DATA_GI_LTF(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, GENMASK(14, 12)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_DATA_GI_LTF, \
+			   GENMASK(14, 12)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DARF_TC_INDEX BIT(0)
+#define SET_CMC_TBL_DARF_TC_INDEX(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(15)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_DARF_TC_INDEX, \
+			   BIT(15)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ARFR_CTRL GENMASK(3, 0)
+#define SET_CMC_TBL_ARFR_CTRL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, GENMASK(19, 16)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_ARFR_CTRL, \
+			   GENMASK(19, 16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ACQ_RPT_EN BIT(0)
+#define SET_CMC_TBL_ACQ_RPT_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(20)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_ACQ_RPT_EN, \
+			   BIT(20)); \
+} while (0)
+#define SET_CMC_TBL_MASK_MGQ_RPT_EN BIT(0)
+#define SET_CMC_TBL_MGQ_RPT_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(21)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_MGQ_RPT_EN, \
+			   BIT(21)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ULQ_RPT_EN BIT(0)
+#define SET_CMC_TBL_ULQ_RPT_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(22)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_ULQ_RPT_EN, \
+			   BIT(22)); \
+} while (0)
+#define SET_CMC_TBL_MASK_TWTQ_RPT_EN BIT(0)
+#define SET_CMC_TBL_TWTQ_RPT_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(23)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_TWTQ_RPT_EN, \
+			   BIT(23)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DISRTSFB BIT(0)
+#define SET_CMC_TBL_DISRTSFB(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(25)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_DISRTSFB, \
+			   BIT(25)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DISDATAFB BIT(0)
+#define SET_CMC_TBL_DISDATAFB(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(26)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_DISDATAFB, \
+			   BIT(26)); \
+} while (0)
+#define SET_CMC_TBL_MASK_TRYRATE BIT(0)
+#define SET_CMC_TBL_TRYRATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, BIT(27)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_TRYRATE, \
+			   BIT(27)); \
+} while (0)
+#define SET_CMC_TBL_MASK_AMPDU_DENSITY GENMASK(3, 0)
+#define SET_CMC_TBL_AMPDU_DENSITY(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 1, val, GENMASK(31, 28)); \
+	le32p_replace_bits((__le32 *)(table) + 9, SET_CMC_TBL_MASK_AMPDU_DENSITY, \
+			   GENMASK(31, 28)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_RTY_LOWEST_RATE GENMASK(8, 0)
+#define SET_CMC_TBL_DATA_RTY_LOWEST_RATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, GENMASK(8, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_DATA_RTY_LOWEST_RATE, \
+			   GENMASK(8, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_AMPDU_TIME_SEL BIT(0)
+#define SET_CMC_TBL_AMPDU_TIME_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, BIT(9)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_AMPDU_TIME_SEL, \
+			   BIT(9)); \
+} while (0)
+#define SET_CMC_TBL_MASK_AMPDU_LEN_SEL BIT(0)
+#define SET_CMC_TBL_AMPDU_LEN_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, BIT(10)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_AMPDU_LEN_SEL, \
+			   BIT(10)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RTS_TXCNT_LMT_SEL BIT(0)
+#define SET_CMC_TBL_RTS_TXCNT_LMT_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, BIT(11)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_RTS_TXCNT_LMT_SEL, \
+			   BIT(11)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RTS_TXCNT_LMT GENMASK(3, 0)
+#define SET_CMC_TBL_RTS_TXCNT_LMT(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, GENMASK(15, 12)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_RTS_TXCNT_LMT, \
+			   GENMASK(15, 12)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RTSRATE GENMASK(8, 0)
+#define SET_CMC_TBL_RTSRATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, GENMASK(24, 16)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_RTSRATE, \
+			   GENMASK(24, 16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_VCS_STBC BIT(0)
+#define SET_CMC_TBL_VCS_STBC(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, BIT(27)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_VCS_STBC, \
+			   BIT(27)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RTS_RTY_LOWEST_RATE GENMASK(3, 0)
+#define SET_CMC_TBL_RTS_RTY_LOWEST_RATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 2, val, GENMASK(31, 28)); \
+	le32p_replace_bits((__le32 *)(table) + 10, SET_CMC_TBL_MASK_RTS_RTY_LOWEST_RATE, \
+			   GENMASK(31, 28)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_TX_CNT_LMT GENMASK(5, 0)
+#define SET_CMC_TBL_DATA_TX_CNT_LMT(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, GENMASK(5, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_DATA_TX_CNT_LMT, \
+			   GENMASK(5, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_TXCNT_LMT_SEL BIT(0)
+#define SET_CMC_TBL_DATA_TXCNT_LMT_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, BIT(6)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_DATA_TXCNT_LMT_SEL, \
+			   BIT(6)); \
+} while (0)
+#define SET_CMC_TBL_MASK_MAX_AGG_NUM_SEL BIT(0)
+#define SET_CMC_TBL_MAX_AGG_NUM_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, BIT(7)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_MAX_AGG_NUM_SEL, \
+			   BIT(7)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RTS_EN BIT(0)
+#define SET_CMC_TBL_RTS_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, BIT(8)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_RTS_EN, \
+			   BIT(8)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CTS2SELF_EN BIT(0)
+#define SET_CMC_TBL_CTS2SELF_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, BIT(9)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_CTS2SELF_EN, \
+			   BIT(9)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CCA_RTS GENMASK(1, 0)
+#define SET_CMC_TBL_CCA_RTS(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, GENMASK(11, 10)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_CCA_RTS, \
+			   GENMASK(11, 10)); \
+} while (0)
+#define SET_CMC_TBL_MASK_HW_RTS_EN BIT(0)
+#define SET_CMC_TBL_HW_RTS_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, BIT(12)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_HW_RTS_EN, \
+			   BIT(12)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RTS_DROP_DATA_MODE GENMASK(1, 0)
+#define SET_CMC_TBL_RTS_DROP_DATA_MODE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, GENMASK(14, 13)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_RTS_DROP_DATA_MODE, \
+			   GENMASK(14, 13)); \
+} while (0)
+#define SET_CMC_TBL_MASK_AMPDU_MAX_LEN GENMASK(10, 0)
+#define SET_CMC_TBL_AMPDU_MAX_LEN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, GENMASK(26, 16)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_AMPDU_MAX_LEN, \
+			   GENMASK(26, 16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_UL_MU_DIS BIT(0)
+#define SET_CMC_TBL_UL_MU_DIS(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, BIT(27)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_UL_MU_DIS, \
+			   BIT(27)); \
+} while (0)
+#define SET_CMC_TBL_MASK_AMPDU_MAX_TIME GENMASK(3, 0)
+#define SET_CMC_TBL_AMPDU_MAX_TIME(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 3, val, GENMASK(31, 28)); \
+	le32p_replace_bits((__le32 *)(table) + 11, SET_CMC_TBL_MASK_AMPDU_MAX_TIME, \
+			   GENMASK(31, 28)); \
+} while (0)
+#define SET_CMC_TBL_MASK_MAX_AGG_NUM GENMASK(7, 0)
+#define SET_CMC_TBL_MAX_AGG_NUM(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(7, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_MAX_AGG_NUM, \
+			   GENMASK(7, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_BA_BMAP GENMASK(1, 0)
+#define SET_CMC_TBL_BA_BMAP(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(9, 8)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_BA_BMAP, \
+			   GENMASK(9, 8)); \
+} while (0)
+#define SET_CMC_TBL_MASK_VO_LFTIME_SEL GENMASK(2, 0)
+#define SET_CMC_TBL_VO_LFTIME_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(18, 16)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_VO_LFTIME_SEL, \
+			   GENMASK(18, 16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_VI_LFTIME_SEL GENMASK(2, 0)
+#define SET_CMC_TBL_VI_LFTIME_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(21, 19)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_VI_LFTIME_SEL, \
+			   GENMASK(21, 19)); \
+} while (0)
+#define SET_CMC_TBL_MASK_BE_LFTIME_SEL GENMASK(2, 0)
+#define SET_CMC_TBL_BE_LFTIME_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(24, 22)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_BE_LFTIME_SEL, \
+			   GENMASK(24, 22)); \
+} while (0)
+#define SET_CMC_TBL_MASK_BK_LFTIME_SEL GENMASK(2, 0)
+#define SET_CMC_TBL_BK_LFTIME_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(27, 25)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_BK_LFTIME_SEL, \
+			   GENMASK(27, 25)); \
+} while (0)
+#define SET_CMC_TBL_MASK_SECTYPE GENMASK(3, 0)
+#define SET_CMC_TBL_SECTYPE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 4, val, GENMASK(31, 28)); \
+	le32p_replace_bits((__le32 *)(table) + 12, SET_CMC_TBL_MASK_SECTYPE, \
+			   GENMASK(31, 28)); \
+} while (0)
+#define SET_CMC_TBL_MASK_MULTI_PORT_ID GENMASK(2, 0)
+#define SET_CMC_TBL_MULTI_PORT_ID(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, GENMASK(2, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_MULTI_PORT_ID, \
+			   GENMASK(2, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_BMC BIT(0)
+#define SET_CMC_TBL_BMC(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(3)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_BMC, \
+			   BIT(3)); \
+} while (0)
+#define SET_CMC_TBL_MASK_MBSSID GENMASK(3, 0)
+#define SET_CMC_TBL_MBSSID(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, GENMASK(7, 4)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_MBSSID, \
+			   GENMASK(7, 4)); \
+} while (0)
+#define SET_CMC_TBL_MASK_NAVUSEHDR BIT(0)
+#define SET_CMC_TBL_NAVUSEHDR(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(8)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_NAVUSEHDR, \
+			   BIT(8)); \
+} while (0)
+#define SET_CMC_TBL_MASK_TXPWR_MODE GENMASK(2, 0)
+#define SET_CMC_TBL_TXPWR_MODE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, GENMASK(11, 9)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_TXPWR_MODE, \
+			   GENMASK(11, 9)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_DCM BIT(0)
+#define SET_CMC_TBL_DATA_DCM(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(12)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_DATA_DCM, \
+			   BIT(12)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_ER BIT(0)
+#define SET_CMC_TBL_DATA_ER(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(13)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_DATA_ER, \
+			   BIT(13)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_LDPC BIT(0)
+#define SET_CMC_TBL_DATA_LDPC(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(14)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_DATA_LDPC, \
+			   BIT(14)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_STBC BIT(0)
+#define SET_CMC_TBL_DATA_STBC(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(15)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_DATA_STBC, \
+			   BIT(15)); \
+} while (0)
+#define SET_CMC_TBL_MASK_A_CTRL_BQR BIT(0)
+#define SET_CMC_TBL_A_CTRL_BQR(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(16)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_A_CTRL_BQR, \
+			   BIT(16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_A_CTRL_UPH BIT(0)
+#define SET_CMC_TBL_A_CTRL_UPH(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(17)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_A_CTRL_UPH, \
+			   BIT(17)); \
+} while (0)
+#define SET_CMC_TBL_MASK_A_CTRL_BSR BIT(0)
+#define SET_CMC_TBL_A_CTRL_BSR(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(18)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_A_CTRL_BSR, \
+			   BIT(18)); \
+} while (0)
+#define SET_CMC_TBL_MASK_A_CTRL_CAS BIT(0)
+#define SET_CMC_TBL_A_CTRL_CAS(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(19)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_A_CTRL_CAS, \
+			   BIT(19)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DATA_BW_ER BIT(0)
+#define SET_CMC_TBL_DATA_BW_ER(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(20)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_DATA_BW_ER, \
+			   BIT(20)); \
+} while (0)
+#define SET_CMC_TBL_MASK_LSIG_TXOP_EN BIT(0)
+#define SET_CMC_TBL_LSIG_TXOP_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(21)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_LSIG_TXOP_EN, \
+			   BIT(21)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CTRL_CNT_VLD BIT(0)
+#define SET_CMC_TBL_CTRL_CNT_VLD(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, BIT(27)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_CTRL_CNT_VLD, \
+			   BIT(27)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CTRL_CNT GENMASK(3, 0)
+#define SET_CMC_TBL_CTRL_CNT(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 5, val, GENMASK(31, 28)); \
+	le32p_replace_bits((__le32 *)(table) + 13, SET_CMC_TBL_MASK_CTRL_CNT, \
+			   GENMASK(31, 28)); \
+} while (0)
+#define SET_CMC_TBL_MASK_RESP_REF_RATE GENMASK(8, 0)
+#define SET_CMC_TBL_RESP_REF_RATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, GENMASK(8, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_RESP_REF_RATE, \
+			   GENMASK(8, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ALL_ACK_SUPPORT BIT(0)
+#define SET_CMC_TBL_ALL_ACK_SUPPORT(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, BIT(12)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_ALL_ACK_SUPPORT, \
+			   BIT(12)); \
+} while (0)
+#define SET_CMC_TBL_MASK_BSR_QUEUE_SIZE_FORMAT BIT(0)
+#define SET_CMC_TBL_BSR_QUEUE_SIZE_FORMAT(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, BIT(13)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_BSR_QUEUE_SIZE_FORMAT, \
+			   BIT(13)); \
+} while (0)
+#define SET_CMC_TBL_MASK_NTX_PATH_EN GENMASK(3, 0)
+#define SET_CMC_TBL_NTX_PATH_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, GENMASK(19, 16)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_NTX_PATH_EN, \
+			   GENMASK(19, 16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_PATH_MAP_A GENMASK(1, 0)
+#define SET_CMC_TBL_PATH_MAP_A(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, GENMASK(21, 20)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_PATH_MAP_A, \
+			   GENMASK(21, 20)); \
+} while (0)
+#define SET_CMC_TBL_MASK_PATH_MAP_B GENMASK(1, 0)
+#define SET_CMC_TBL_PATH_MAP_B(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, GENMASK(23, 22)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_PATH_MAP_B, \
+			   GENMASK(23, 22)); \
+} while (0)
+#define SET_CMC_TBL_MASK_PATH_MAP_C GENMASK(1, 0)
+#define SET_CMC_TBL_PATH_MAP_C(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, GENMASK(25, 24)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_PATH_MAP_C, \
+			   GENMASK(25, 24)); \
+} while (0)
+#define SET_CMC_TBL_MASK_PATH_MAP_D GENMASK(1, 0)
+#define SET_CMC_TBL_PATH_MAP_D(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, GENMASK(27, 26)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_PATH_MAP_D, \
+			   GENMASK(27, 26)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ANTSEL_A BIT(0)
+#define SET_CMC_TBL_ANTSEL_A(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, BIT(28)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_ANTSEL_A, \
+			   BIT(28)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ANTSEL_B BIT(0)
+#define SET_CMC_TBL_ANTSEL_B(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, BIT(29)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_ANTSEL_B, \
+			   BIT(29)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ANTSEL_C BIT(0)
+#define SET_CMC_TBL_ANTSEL_C(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, BIT(30)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_ANTSEL_C, \
+			   BIT(30)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ANTSEL_D BIT(0)
+#define SET_CMC_TBL_ANTSEL_D(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 6, val, BIT(31)); \
+	le32p_replace_bits((__le32 *)(table) + 14, SET_CMC_TBL_MASK_ANTSEL_D, \
+			   BIT(31)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ADDR_CAM_INDEX GENMASK(7, 0)
+#define SET_CMC_TBL_ADDR_CAM_INDEX(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(7, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_ADDR_CAM_INDEX, \
+			   GENMASK(7, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_PAID GENMASK(8, 0)
+#define SET_CMC_TBL_PAID(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(16, 8)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_PAID, \
+			   GENMASK(16, 8)); \
+} while (0)
+#define SET_CMC_TBL_MASK_ULDL BIT(0)
+#define SET_CMC_TBL_ULDL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, BIT(17)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_ULDL, \
+			   BIT(17)); \
+} while (0)
+#define SET_CMC_TBL_MASK_DOPPLER_CTRL GENMASK(1, 0)
+#define SET_CMC_TBL_DOPPLER_CTRL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(19, 18)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_DOPPLER_CTRL, \
+			   GENMASK(19, 18)); \
+} while (0)
+#define SET_CMC_TBL_MASK_NOMINAL_PKT_PADDING GENMASK(1, 0)
+#define SET_CMC_TBL_NOMINAL_PKT_PADDING(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(21, 20)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_NOMINAL_PKT_PADDING, \
+			   GENMASK(21, 20)); \
+} while (0)
+#define SET_CMC_TBL_NOMINAL_PKT_PADDING40(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(23, 22)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_NOMINAL_PKT_PADDING, \
+			   GENMASK(23, 22)); \
+} while (0)
+#define SET_CMC_TBL_MASK_TXPWR_TOLERENCE GENMASK(3, 0)
+#define SET_CMC_TBL_TXPWR_TOLERENCE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(27, 24)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_TXPWR_TOLERENCE, \
+			   GENMASK(27, 24)); \
+} while (0)
+#define SET_CMC_TBL_NOMINAL_PKT_PADDING80(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 7, val, GENMASK(31, 30)); \
+	le32p_replace_bits((__le32 *)(table) + 15, SET_CMC_TBL_MASK_NOMINAL_PKT_PADDING, \
+			   GENMASK(31, 30)); \
+} while (0)
+#define SET_CMC_TBL_MASK_NC GENMASK(2, 0)
+#define SET_CMC_TBL_NC(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(2, 0)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_NC, \
+			   GENMASK(2, 0)); \
+} while (0)
+#define SET_CMC_TBL_MASK_NR GENMASK(2, 0)
+#define SET_CMC_TBL_NR(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(5, 3)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_NR, \
+			   GENMASK(5, 3)); \
+} while (0)
+#define SET_CMC_TBL_MASK_NG GENMASK(1, 0)
+#define SET_CMC_TBL_NG(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(7, 6)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_NG, \
+			   GENMASK(7, 6)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CB GENMASK(1, 0)
+#define SET_CMC_TBL_CB(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(9, 8)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CB, \
+			   GENMASK(9, 8)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CS GENMASK(1, 0)
+#define SET_CMC_TBL_CS(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(11, 10)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CS, \
+			   GENMASK(11, 10)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_TXBF_EN BIT(0)
+#define SET_CMC_TBL_CSI_TXBF_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, BIT(12)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_TXBF_EN, \
+			   BIT(12)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_STBC_EN BIT(0)
+#define SET_CMC_TBL_CSI_STBC_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, BIT(13)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_STBC_EN, \
+			   BIT(13)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_LDPC_EN BIT(0)
+#define SET_CMC_TBL_CSI_LDPC_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, BIT(14)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_LDPC_EN, \
+			   BIT(14)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_PARA_EN BIT(0)
+#define SET_CMC_TBL_CSI_PARA_EN(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, BIT(15)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_PARA_EN, \
+			   BIT(15)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_FIX_RATE GENMASK(8, 0)
+#define SET_CMC_TBL_CSI_FIX_RATE(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(24, 16)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_FIX_RATE, \
+			   GENMASK(24, 16)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_GI_LTF GENMASK(2, 0)
+#define SET_CMC_TBL_CSI_GI_LTF(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(27, 25)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_GI_LTF, \
+			   GENMASK(27, 25)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_GID_SEL BIT(0)
+#define SET_CMC_TBL_CSI_GID_SEL(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, BIT(29)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_GID_SEL, \
+			   BIT(29)); \
+} while (0)
+#define SET_CMC_TBL_MASK_CSI_BW GENMASK(1, 0)
+#define SET_CMC_TBL_CSI_BW(table, val) \
+do { \
+	le32p_replace_bits((__le32 *)(table) + 8, val, GENMASK(31, 30)); \
+	le32p_replace_bits((__le32 *)(table) + 16, SET_CMC_TBL_MASK_CSI_BW, \
+			   GENMASK(31, 30)); \
+} while (0)
+
+#define SET_FWROLE_MAINTAIN_MACID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(7, 0))
+#define SET_FWROLE_MAINTAIN_SELF_ROLE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(9, 8))
+#define SET_FWROLE_MAINTAIN_UPD_MODE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(12, 10))
+#define SET_FWROLE_MAINTAIN_WIFI_ROLE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(16, 13))
+
+#define SET_JOININFO_MACID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(7, 0))
+#define SET_JOININFO_OP(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, BIT(8))
+#define SET_JOININFO_BAND(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, BIT(9))
+#define SET_JOININFO_WMM(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(11, 10))
+#define SET_JOININFO_TGR(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, BIT(12))
+#define SET_JOININFO_ISHESTA(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, BIT(13))
+#define SET_JOININFO_DLBW(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(15, 14))
+#define SET_JOININFO_TF_MAC_PAD(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(17, 16))
+#define SET_JOININFO_DL_T_PE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(20, 18))
+#define SET_JOININFO_PORT_ID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(23, 21))
+#define SET_JOININFO_NET_TYPE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(25, 24))
+#define SET_JOININFO_WIFI_ROLE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(29, 26))
+#define SET_JOININFO_SELF_ROLE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(31, 30))
+
+#define SET_GENERAL_PKT_MACID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(7, 0))
+#define SET_GENERAL_PKT_PROBRSP_ID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(15, 8))
+#define SET_GENERAL_PKT_PSPOLL_ID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(23, 16))
+#define SET_GENERAL_PKT_NULL_ID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(31, 24))
+#define SET_GENERAL_PKT_QOS_NULL_ID(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, GENMASK(7, 0))
+#define SET_GENERAL_PKT_CTS2SELF_ID(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, GENMASK(15, 8))
+
+#define SET_LOG_CFG_LEVEL(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(7, 0))
+#define SET_LOG_CFG_PATH(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(15, 8))
+#define SET_LOG_CFG_COMP(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, GENMASK(31, 0))
+#define SET_LOG_CFG_COMP_EXT(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 2, val, GENMASK(31, 0))
+
+#define SET_BA_CAM_VALID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, BIT(0))
+#define SET_BA_CAM_INIT_REQ(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, BIT(1))
+#define SET_BA_CAM_ENTRY_IDX(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(3, 2))
+#define SET_BA_CAM_TID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(7, 4))
+#define SET_BA_CAM_MACID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(15, 8))
+#define SET_BA_CAM_BMAP_SIZE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(19, 16))
+#define SET_BA_CAM_SSN(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(31, 20))
+
+#define SET_LPS_PARM_MACID(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(7, 0))
+#define SET_LPS_PARM_PSMODE(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(15, 8))
+#define SET_LPS_PARM_RLBM(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(19, 16))
+#define SET_LPS_PARM_SMARTPS(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(23, 20))
+#define SET_LPS_PARM_AWAKEINTERVAL(h2c, val) \
+	le32p_replace_bits((__le32 *)h2c, val, GENMASK(31, 24))
+#define SET_LPS_PARM_VOUAPSD(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, BIT(0))
+#define SET_LPS_PARM_VIUAPSD(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, BIT(1))
+#define SET_LPS_PARM_BEUAPSD(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, BIT(2))
+#define SET_LPS_PARM_BKUAPSD(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, BIT(3))
+#define SET_LPS_PARM_LASTRPWM(h2c, val) \
+	le32p_replace_bits((__le32 *)(h2c) + 1, val, GENMASK(15, 8))
+
+enum rtw89_btc_btf_h2c_class {
+	BTFC_SET = 0x10,
+	BTFC_GET = 0x11,
+	BTFC_FW_EVENT = 0x12,
+};
+
+enum rtw89_btc_btf_set {
+	SET_REPORT_EN = 0x0,
+	SET_SLOT_TABLE,
+	SET_MREG_TABLE,
+	SET_CX_POLICY,
+	SET_GPIO_DBG,
+	SET_DRV_INFO,
+	SET_DRV_EVENT,
+	SET_BT_WREG_ADDR,
+	SET_BT_WREG_VAL,
+	SET_BT_RREG_ADDR,
+	SET_BT_WL_CH_INFO,
+	SET_BT_INFO_REPORT,
+	SET_BT_IGNORE_WLAN_ACT,
+	SET_BT_TX_PWR,
+	SET_BT_LNA_CONSTRAIN,
+	SET_BT_GOLDEN_RX_RANGE,
+	SET_BT_PSD_REPORT,
+	SET_H2C_TEST,
+	SET_MAX1,
+};
+
+enum rtw89_btc_cxdrvinfo {
+	CXDRVINFO_INIT = 0,
+	CXDRVINFO_ROLE,
+	CXDRVINFO_DBCC,
+	CXDRVINFO_SMAP,
+	CXDRVINFO_RFK,
+	CXDRVINFO_RUN,
+	CXDRVINFO_CTRL,
+	CXDRVINFO_SCAN,
+	CXDRVINFO_MAX,
+};
+
+#define RTW89_SET_FWCMD_CXHDR_TYPE(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 0, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXHDR_LEN(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 1, val, GENMASK(7, 0))
+
+#define RTW89_SET_FWCMD_CXINIT_ANT_TYPE(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 2, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXINIT_ANT_NUM(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 3, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXINIT_ANT_ISO(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 4, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXINIT_ANT_POS(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 5, val, BIT(0))
+#define RTW89_SET_FWCMD_CXINIT_ANT_DIVERSITY(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 5, val, BIT(1))
+#define RTW89_SET_FWCMD_CXINIT_MOD_RFE(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 6, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXINIT_MOD_CV(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 7, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXINIT_MOD_BT_SOLO(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 8, val, BIT(0))
+#define RTW89_SET_FWCMD_CXINIT_MOD_BT_POS(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 8, val, BIT(1))
+#define RTW89_SET_FWCMD_CXINIT_MOD_SW_TYPE(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 8, val, BIT(2))
+#define RTW89_SET_FWCMD_CXINIT_WL_GCH(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 10, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXINIT_WL_ONLY(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 11, val, BIT(0))
+#define RTW89_SET_FWCMD_CXINIT_WL_INITOK(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 11, val, BIT(1))
+#define RTW89_SET_FWCMD_CXINIT_DBCC_EN(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 11, val, BIT(2))
+#define RTW89_SET_FWCMD_CXINIT_CX_OTHER(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 11, val, BIT(3))
+#define RTW89_SET_FWCMD_CXINIT_BT_ONLY(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 11, val, BIT(4))
+
+#define RTW89_SET_FWCMD_CXROLE_CONNECT_CNT(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 2, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXROLE_LINK_MODE(cmd, val) \
+	u8p_replace_bits((u8 *)(cmd) + 3, val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_NONE(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(0))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_STA(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(1))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_AP(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(2))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_VAP(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(3))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_ADHOC(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(4))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_ADHOC_MASTER(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(5))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_MESH(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(6))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_MONITOR(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(7))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_P2P_DEV(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(8))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_P2P_GC(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(9))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_P2P_GO(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(10))
+#define RTW89_SET_FWCMD_CXROLE_ROLE_NAN(cmd, val) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + 4), val, BIT(11))
+#define RTW89_SET_FWCMD_CXROLE_ACT_CONNECTED(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (6 + 12 * (n)), val, BIT(0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_PID(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (6 + 12 * (n)), val, GENMASK(3, 1))
+#define RTW89_SET_FWCMD_CXROLE_ACT_PHY(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (6 + 12 * (n)), val, BIT(4))
+#define RTW89_SET_FWCMD_CXROLE_ACT_NOA(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (6 + 12 * (n)), val, BIT(5))
+#define RTW89_SET_FWCMD_CXROLE_ACT_BAND(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (6 + 12 * (n)), val, GENMASK(7, 6))
+#define RTW89_SET_FWCMD_CXROLE_ACT_CLIENT_PS(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (7 + 12 * (n)), val, BIT(0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_BW(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (7 + 12 * (n)), val, GENMASK(7, 1))
+#define RTW89_SET_FWCMD_CXROLE_ACT_ROLE(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (8 + 12 * (n)), val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_CH(cmd, val, n) \
+	u8p_replace_bits((u8 *)(cmd) + (9 + 12 * (n)), val, GENMASK(7, 0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_TX_LVL(cmd, val, n) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + (10 + 12 * (n))), val, GENMASK(15, 0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_RX_LVL(cmd, val, n) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + (12 + 12 * (n))), val, GENMASK(15, 0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_TX_RATE(cmd, val, n) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + (14 + 12 * (n))), val, GENMASK(15, 0))
+#define RTW89_SET_FWCMD_CXROLE_ACT_RX_RATE(cmd, val, n) \
+	le16p_replace_bits((__le16 *)((u8 *)(cmd) + (16 + 12 * (n))), val, GENMASK(15, 0))
+
+#define RTW89_SET_FWCMD_CXCTRL_MANUAL(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, BIT(0))
+#define RTW89_SET_FWCMD_CXCTRL_IGNORE_BT(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, BIT(1))
+#define RTW89_SET_FWCMD_CXCTRL_ALWAYS_FREERUN(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, BIT(2))
+#define RTW89_SET_FWCMD_CXCTRL_TRACE_STEP(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, GENMASK(18, 3))
+
+#define RTW89_SET_FWCMD_CXRFK_STATE(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, GENMASK(1, 0))
+#define RTW89_SET_FWCMD_CXRFK_PATH_MAP(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, GENMASK(5, 2))
+#define RTW89_SET_FWCMD_CXRFK_PHY_MAP(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, GENMASK(7, 6))
+#define RTW89_SET_FWCMD_CXRFK_BAND(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, GENMASK(9, 8))
+#define RTW89_SET_FWCMD_CXRFK_TYPE(cmd, val) \
+	le32p_replace_bits((__le32 *)((u8 *)(cmd) + 2), val, GENMASK(17, 10))
+
+#define RTW89_C2H_HEADER_LEN 8
+
+#define RTW89_GET_C2H_CATEGORY(c2h) \
+	le32_get_bits(*((__le32 *)c2h), GENMASK(1, 0))
+#define RTW89_GET_C2H_CLASS(c2h) \
+	le32_get_bits(*((__le32 *)c2h), GENMASK(7, 2))
+#define RTW89_GET_C2H_FUNC(c2h) \
+	le32_get_bits(*((__le32 *)c2h), GENMASK(15, 8))
+#define RTW89_GET_C2H_LEN(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 1), GENMASK(13, 0))
+
+#define RTW89_GET_C2H_LOG_SRT_PRT(c2h) (char *)((__le32 *)(c2h) + 2)
+#define RTW89_GET_C2H_LOG_LEN(len) ((len) - RTW89_C2H_HEADER_LEN)
+
+#define RTW89_GET_MAC_C2H_DONE_ACK_CAT(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(1, 0))
+#define RTW89_GET_MAC_C2H_DONE_ACK_CLASS(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(7, 2))
+#define RTW89_GET_MAC_C2H_DONE_ACK_FUNC(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(15, 8))
+#define RTW89_GET_MAC_C2H_DONE_ACK_H2C_RETURN(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(23, 16))
+#define RTW89_GET_MAC_C2H_DONE_ACK_H2C_SEQ(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(31, 24))
+
+#define RTW89_GET_MAC_C2H_REV_ACK_CAT(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(1, 0))
+#define RTW89_GET_MAC_C2H_REV_ACK_CLASS(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(7, 2))
+#define RTW89_GET_MAC_C2H_REV_ACK_FUNC(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(15, 8))
+#define RTW89_GET_MAC_C2H_REV_ACK_H2C_SEQ(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(23, 16))
+
+#define RTW89_GET_PHY_C2H_RA_RPT_MACID(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(15, 0))
+#define RTW89_GET_PHY_C2H_RA_RPT_RETRY_RATIO(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 2), GENMASK(23, 16))
+#define RTW89_GET_PHY_C2H_RA_RPT_MCSNSS(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 3), GENMASK(6, 0))
+#define RTW89_GET_PHY_C2H_RA_RPT_MD_SEL(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 3), GENMASK(9, 8))
+#define RTW89_GET_PHY_C2H_RA_RPT_GILTF(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 3), GENMASK(12, 10))
+#define RTW89_GET_PHY_C2H_RA_RPT_BW(c2h) \
+	le32_get_bits(*((__le32 *)(c2h) + 3), GENMASK(14, 13))
+
+/* VHT, HE, HT-old: [6:4]: NSS, [3:0]: MCS
+ * HT-new: [6:5]: NA, [4:0]: MCS
+ */
+#define RTW89_RA_RATE_MASK_NSS GENMASK(6, 4)
+#define RTW89_RA_RATE_MASK_MCS GENMASK(3, 0)
+#define RTW89_RA_RATE_MASK_HT_MCS GENMASK(4, 0)
+#define RTW89_MK_HT_RATE(nss, mcs) (FIELD_PREP(GENMASK(4, 3), nss) | \
+				    FIELD_PREP(GENMASK(2, 0), mcs))
+
+#define RTW89_FW_HDR_SIZE 32
+#define RTW89_FW_SECTION_HDR_SIZE 16
+
+#define RTW89_MFW_SIG	0xFF
+
+struct rtw89_mfw_info {
+	u8 cv;
+	u8 type; /* enum rtw89_fw_type */
+	u8 mp;
+	u8 rsvd;
+	__le32 shift;
+	__le32 size;
+	u8 rsvd2[4];
+} __packed;
+
+struct rtw89_mfw_hdr {
+	u8 sig;	/* RTW89_MFW_SIG */
+	u8 fw_nr;
+	u8 rsvd[14];
+	struct rtw89_mfw_info info[];
+} __packed;
+
+struct fwcmd_hdr {
+	__le32 hdr0;
+	__le32 hdr1;
+};
+
+#define RTW89_H2C_RF_PAGE_SIZE 500
+#define RTW89_H2C_RF_PAGE_NUM 3
+struct rtw89_fw_h2c_rf_reg_info {
+	enum rtw89_rf_path rf_path;
+	__le32 rtw89_phy_config_rf_h2c[RTW89_H2C_RF_PAGE_NUM][RTW89_H2C_RF_PAGE_SIZE];
+	u16 curr_idx;
+};
+
+#define H2C_SEC_CAM_LEN			24
+
+#define H2C_HEADER_LEN			8
+#define H2C_HDR_CAT			GENMASK(1, 0)
+#define H2C_HDR_CLASS			GENMASK(7, 2)
+#define H2C_HDR_FUNC			GENMASK(15, 8)
+#define H2C_HDR_DEL_TYPE		GENMASK(19, 16)
+#define H2C_HDR_H2C_SEQ			GENMASK(31, 24)
+#define H2C_HDR_TOTAL_LEN		GENMASK(13, 0)
+#define H2C_HDR_REC_ACK			BIT(14)
+#define H2C_HDR_DONE_ACK		BIT(15)
+
+#define FWCMD_TYPE_H2C			0
+
+#define H2C_CAT_MAC		0x1
+
+/* CLASS 0 - FW INFO */
+#define H2C_CL_FW_INFO			0x0
+#define H2C_FUNC_LOG_CFG		0x0
+#define H2C_FUNC_MAC_GENERAL_PKT	0x1
+
+/* CLASS 2 - PS */
+#define H2C_CL_MAC_PS			0x2
+#define H2C_FUNC_MAC_LPS_PARM		0x0
+
+/* CLASS 3 - FW download */
+#define H2C_CL_MAC_FWDL		0x3
+#define H2C_FUNC_MAC_FWHDR_DL		0x0
+
+/* CLASS 5 - Frame Exchange */
+#define H2C_CL_MAC_FR_EXCHG		0x5
+#define H2C_FUNC_MAC_CCTLINFO_UD	0x2
+
+/* CLASS 6 - Address CAM */
+#define H2C_CL_MAC_ADDR_CAM_UPDATE	0x6
+#define H2C_FUNC_MAC_ADDR_CAM_UPD	0x0
+
+/* CLASS 8 - Media Status Report */
+#define H2C_CL_MAC_MEDIA_RPT		0x8
+#define H2C_FUNC_MAC_JOININFO		0x0
+#define H2C_FUNC_MAC_FWROLE_MAINTAIN	0x4
+
+/* CLASS 9 - FW offload */
+#define H2C_CL_MAC_FW_OFLD		0x9
+#define H2C_FUNC_MAC_MACID_PAUSE	0x8
+#define H2C_FUNC_USR_EDCA		0xF
+#define H2C_FUNC_OFLD_CFG		0x14
+
+/* CLASS 10 - Security CAM */
+#define H2C_CL_MAC_SEC_CAM		0xa
+#define H2C_FUNC_MAC_SEC_UPD		0x1
+
+/* CLASS 12 - BA CAM */
+#define H2C_CL_BA_CAM			0xc
+#define H2C_FUNC_MAC_BA_CAM		0x0
+
+#define H2C_CAT_OUTSRC			0x2
+
+#define H2C_CL_OUTSRC_RA		0x1
+#define H2C_FUNC_OUTSRC_RA_MACIDCFG	0x0
+
+#define H2C_CL_OUTSRC_RF_REG_A		0x8
+#define H2C_CL_OUTSRC_RF_REG_B		0x9
+
+int rtw89_fw_check_rdy(struct rtw89_dev *rtwdev);
+int rtw89_fw_recognize(struct rtw89_dev *rtwdev);
+int rtw89_fw_download(struct rtw89_dev *rtwdev, enum rtw89_fw_type type);
+int rtw89_load_firmware(struct rtw89_dev *rtwdev);
+void rtw89_unload_firmware(struct rtw89_dev *rtwdev);
+int rtw89_wait_firmware_completion(struct rtw89_dev *rtwdev);
+void rtw89_h2c_pkt_set_hdr(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			   u8 type, u8 cat, u8 class, u8 func,
+			   bool rack, bool dack, u32 len);
+int rtw89_fw_h2c_default_cmac_tbl(struct rtw89_dev *rtwdev, u8 macid);
+int rtw89_fw_h2c_assoc_cmac_tbl(struct rtw89_dev *rtwdev,
+				struct ieee80211_vif *vif,
+				struct ieee80211_sta *sta);
+int rtw89_fw_h2c_txtime_cmac_tbl(struct rtw89_dev *rtwdev,
+				 struct rtw89_sta *rtwsta);
+int rtw89_fw_h2c_cam(struct rtw89_dev *rtwdev, struct rtw89_vif *vif);
+void rtw89_fw_c2h_irqsafe(struct rtw89_dev *rtwdev, struct sk_buff *c2h);
+void rtw89_fw_c2h_work(struct work_struct *work);
+int rtw89_fw_h2c_vif_maintain(struct rtw89_dev *rtwdev,
+			      struct rtw89_vif *rtwvif,
+			      enum rtw89_upd_mode upd_mode);
+int rtw89_fw_h2c_join_info(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			   u8 dis_conn);
+int rtw89_fw_h2c_macid_pause(struct rtw89_dev *rtwdev, u8 sh, u8 grp,
+			     bool pause);
+int rtw89_fw_h2c_set_edca(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			  u8 ac, u32 val);
+int rtw89_fw_h2c_set_ofld_cfg(struct rtw89_dev *rtwdev);
+int rtw89_fw_h2c_ra(struct rtw89_dev *rtwdev, struct rtw89_ra_info *ra, bool csi);
+int rtw89_fw_h2c_cxdrv_init(struct rtw89_dev *rtwdev);
+int rtw89_fw_h2c_cxdrv_role(struct rtw89_dev *rtwdev);
+int rtw89_fw_h2c_cxdrv_ctrl(struct rtw89_dev *rtwdev);
+int rtw89_fw_h2c_cxdrv_rfk(struct rtw89_dev *rtwdev);
+int rtw89_fw_h2c_rf_reg(struct rtw89_dev *rtwdev,
+			struct rtw89_fw_h2c_rf_reg_info *info,
+			u16 len, u8 page);
+int rtw89_fw_h2c_raw_with_hdr(struct rtw89_dev *rtwdev,
+			      u8 h2c_class, u8 h2c_func, u8 *buf, u16 len,
+			      bool rack, bool dack);
+int rtw89_fw_h2c_raw(struct rtw89_dev *rtwdev, const u8 *buf, u16 len);
+void rtw89_fw_send_all_early_h2c(struct rtw89_dev *rtwdev);
+void rtw89_fw_free_all_early_h2c(struct rtw89_dev *rtwdev);
+int rtw89_fw_h2c_general_pkt(struct rtw89_dev *rtwdev, u8 macid);
+int rtw89_fw_h2c_ba_cam(struct rtw89_dev *rtwdev, bool valid, u8 macid,
+			struct ieee80211_ampdu_params *params);
+int rtw89_fw_h2c_lps_parm(struct rtw89_dev *rtwdev,
+			  struct rtw89_lps_parm *lps_param);
+struct sk_buff *rtw89_fw_h2c_alloc_skb_with_hdr(u32 len);
+struct sk_buff *rtw89_fw_h2c_alloc_skb_no_hdr(u32 len);
+int rtw89_fw_msg_reg(struct rtw89_dev *rtwdev,
+		     struct rtw89_mac_h2c_info *h2c_info,
+		     struct rtw89_mac_c2h_info *c2h_info);
+int rtw89_fw_h2c_fw_log(struct rtw89_dev *rtwdev, bool enable);
+void rtw89_fw_st_dbg_dump(struct rtw89_dev *rtwdev);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/mac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/mac.c
@@ -0,0 +1,3836 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "cam.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+#include "ps.h"
+#include "reg.h"
+#include "util.h"
+
+int rtw89_mac_check_mac_en(struct rtw89_dev *rtwdev, u8 mac_idx,
+			   enum rtw89_mac_hwmod_sel sel)
+{
+	u32 val, r_val;
+
+	if (sel == RTW89_DMAC_SEL) {
+		r_val = rtw89_read32(rtwdev, R_AX_DMAC_FUNC_EN);
+		val = (B_AX_MAC_FUNC_EN | B_AX_DMAC_FUNC_EN);
+	} else if (sel == RTW89_CMAC_SEL && mac_idx == 0) {
+		r_val = rtw89_read32(rtwdev, R_AX_CMAC_FUNC_EN);
+		val = B_AX_CMAC_EN;
+	} else if (sel == RTW89_CMAC_SEL && mac_idx == 1) {
+		r_val = rtw89_read32(rtwdev, R_AX_SYS_ISO_CTRL_EXTEND);
+		val = B_AX_CMAC1_FEN;
+	} else {
+		return -EINVAL;
+	}
+	if (r_val == RTW89_R32_EA || r_val == RTW89_R32_DEAD ||
+	    (val & r_val) != val)
+		return -EFAULT;
+
+	return 0;
+}
+
+int rtw89_mac_write_lte(struct rtw89_dev *rtwdev, const u32 offset, u32 val)
+{
+	u8 lte_ctrl;
+	int ret;
+
+	ret = read_poll_timeout(rtw89_read8, lte_ctrl, (lte_ctrl & BIT(5)) != 0,
+				50, 50000, false, rtwdev, R_AX_LTE_CTRL + 3);
+	if (ret)
+		rtw89_err(rtwdev, "[ERR]lte not ready(W)\n");
+
+	rtw89_write32(rtwdev, R_AX_LTE_WDATA, val);
+	rtw89_write32(rtwdev, R_AX_LTE_CTRL, 0xC00F0000 | offset);
+
+	return ret;
+}
+
+int rtw89_mac_read_lte(struct rtw89_dev *rtwdev, const u32 offset, u32 *val)
+{
+	u8 lte_ctrl;
+	int ret;
+
+	ret = read_poll_timeout(rtw89_read8, lte_ctrl, (lte_ctrl & BIT(5)) != 0,
+				50, 50000, false, rtwdev, R_AX_LTE_CTRL + 3);
+	if (ret)
+		rtw89_err(rtwdev, "[ERR]lte not ready(W)\n");
+
+	rtw89_write32(rtwdev, R_AX_LTE_CTRL, 0x800F0000 | offset);
+	*val = rtw89_read32(rtwdev, R_AX_LTE_RDATA);
+
+	return ret;
+}
+
+static
+int dle_dfi_ctrl(struct rtw89_dev *rtwdev, struct rtw89_mac_dle_dfi_ctrl *ctrl)
+{
+	u32 ctrl_reg, data_reg, ctrl_data;
+	u32 val;
+	int ret;
+
+	switch (ctrl->type) {
+	case DLE_CTRL_TYPE_WDE:
+		ctrl_reg = R_AX_WDE_DBG_FUN_INTF_CTL;
+		data_reg = R_AX_WDE_DBG_FUN_INTF_DATA;
+		ctrl_data = FIELD_PREP(B_AX_WDE_DFI_TRGSEL_MASK, ctrl->target) |
+			    FIELD_PREP(B_AX_WDE_DFI_ADDR_MASK, ctrl->addr) |
+			    B_AX_WDE_DFI_ACTIVE;
+		break;
+	case DLE_CTRL_TYPE_PLE:
+		ctrl_reg = R_AX_PLE_DBG_FUN_INTF_CTL;
+		data_reg = R_AX_PLE_DBG_FUN_INTF_DATA;
+		ctrl_data = FIELD_PREP(B_AX_PLE_DFI_TRGSEL_MASK, ctrl->target) |
+			    FIELD_PREP(B_AX_PLE_DFI_ADDR_MASK, ctrl->addr) |
+			    B_AX_PLE_DFI_ACTIVE;
+		break;
+	default:
+		rtw89_warn(rtwdev, "[ERR] dfi ctrl type %d\n", ctrl->type);
+		return -EINVAL;
+	}
+
+	rtw89_write32(rtwdev, ctrl_reg, ctrl_data);
+
+	ret = read_poll_timeout_atomic(rtw89_read32, val, !(val & B_AX_WDE_DFI_ACTIVE),
+				       1, 1000, false, rtwdev, ctrl_reg);
+	if (ret) {
+		rtw89_warn(rtwdev, "[ERR] dle dfi ctrl 0x%X set 0x%X timeout\n",
+			   ctrl_reg, ctrl_data);
+		return ret;
+	}
+
+	ctrl->out_data = rtw89_read32(rtwdev, data_reg);
+	return 0;
+}
+
+static int dle_dfi_quota(struct rtw89_dev *rtwdev,
+			 struct rtw89_mac_dle_dfi_quota *quota)
+{
+	struct rtw89_mac_dle_dfi_ctrl ctrl;
+	int ret;
+
+	ctrl.type = quota->dle_type;
+	ctrl.target = DLE_DFI_TYPE_QUOTA;
+	ctrl.addr = quota->qtaid;
+	ret = dle_dfi_ctrl(rtwdev, &ctrl);
+	if (ret) {
+		rtw89_warn(rtwdev, "[ERR]dle_dfi_ctrl %d\n", ret);
+		return ret;
+	}
+
+	quota->rsv_pgnum = FIELD_GET(B_AX_DLE_RSV_PGNUM, ctrl.out_data);
+	quota->use_pgnum = FIELD_GET(B_AX_DLE_USE_PGNUM, ctrl.out_data);
+	return 0;
+}
+
+static int dle_dfi_qempty(struct rtw89_dev *rtwdev,
+			  struct rtw89_mac_dle_dfi_qempty *qempty)
+{
+	struct rtw89_mac_dle_dfi_ctrl ctrl;
+	u32 ret;
+
+	ctrl.type = qempty->dle_type;
+	ctrl.target = DLE_DFI_TYPE_QEMPTY;
+	ctrl.addr = qempty->grpsel;
+	ret = dle_dfi_ctrl(rtwdev, &ctrl);
+	if (ret) {
+		rtw89_warn(rtwdev, "[ERR]dle_dfi_ctrl %d\n", ret);
+		return ret;
+	}
+
+	qempty->qempty = FIELD_GET(B_AX_DLE_QEMPTY_GRP, ctrl.out_data);
+	return 0;
+}
+
+static void dump_err_status_dispatcher(struct rtw89_dev *rtwdev)
+{
+	rtw89_info(rtwdev, "R_AX_HOST_DISPATCHER_ALWAYS_IMR=0x%08x ",
+		   rtw89_read32(rtwdev, R_AX_HOST_DISPATCHER_ERR_IMR));
+	rtw89_info(rtwdev, "R_AX_HOST_DISPATCHER_ALWAYS_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_HOST_DISPATCHER_ERR_ISR));
+	rtw89_info(rtwdev, "R_AX_CPU_DISPATCHER_ALWAYS_IMR=0x%08x ",
+		   rtw89_read32(rtwdev, R_AX_CPU_DISPATCHER_ERR_IMR));
+	rtw89_info(rtwdev, "R_AX_CPU_DISPATCHER_ALWAYS_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_CPU_DISPATCHER_ERR_ISR));
+	rtw89_info(rtwdev, "R_AX_OTHER_DISPATCHER_ALWAYS_IMR=0x%08x ",
+		   rtw89_read32(rtwdev, R_AX_OTHER_DISPATCHER_ERR_IMR));
+	rtw89_info(rtwdev, "R_AX_OTHER_DISPATCHER_ALWAYS_ISR=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_OTHER_DISPATCHER_ERR_ISR));
+}
+
+static void rtw89_mac_dump_qta_lost(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_mac_dle_dfi_qempty qempty;
+	struct rtw89_mac_dle_dfi_quota quota;
+	struct rtw89_mac_dle_dfi_ctrl ctrl;
+	u32 val, not_empty, i;
+	int ret;
+
+	qempty.dle_type = DLE_CTRL_TYPE_PLE;
+	qempty.grpsel = 0;
+	ret = dle_dfi_qempty(rtwdev, &qempty);
+	if (ret)
+		rtw89_warn(rtwdev, "%s: query DLE fail\n", __func__);
+	else
+		rtw89_info(rtwdev, "DLE group0 empty: 0x%x\n", qempty.qempty);
+
+	for (not_empty = ~qempty.qempty, i = 0; not_empty != 0; not_empty >>= 1, i++) {
+		if (!(not_empty & BIT(0)))
+			continue;
+		ctrl.type = DLE_CTRL_TYPE_PLE;
+		ctrl.target = DLE_DFI_TYPE_QLNKTBL;
+		ctrl.addr = (QLNKTBL_ADDR_INFO_SEL_0 ? QLNKTBL_ADDR_INFO_SEL : 0) |
+			    FIELD_PREP(QLNKTBL_ADDR_TBL_IDX_MASK, i);
+		ret = dle_dfi_ctrl(rtwdev, &ctrl);
+		if (ret)
+			rtw89_warn(rtwdev, "%s: query DLE fail\n", __func__);
+		else
+			rtw89_info(rtwdev, "qidx%d pktcnt = %ld\n", i,
+				   FIELD_GET(QLNKTBL_DATA_SEL1_PKT_CNT_MASK,
+					     ctrl.out_data));
+	}
+
+	quota.dle_type = DLE_CTRL_TYPE_PLE;
+	quota.qtaid = 6;
+	ret = dle_dfi_quota(rtwdev, &quota);
+	if (ret)
+		rtw89_warn(rtwdev, "%s: query DLE fail\n", __func__);
+	else
+		rtw89_info(rtwdev, "quota6 rsv/use: 0x%x/0x%x\n",
+			   quota.rsv_pgnum, quota.use_pgnum);
+
+	val = rtw89_read32(rtwdev, R_AX_PLE_QTA6_CFG);
+	rtw89_info(rtwdev, "[PLE][CMAC0_RX]min_pgnum=0x%lx\n",
+		   FIELD_GET(B_AX_PLE_Q6_MIN_SIZE_MASK, val));
+	rtw89_info(rtwdev, "[PLE][CMAC0_RX]max_pgnum=0x%lx\n",
+		   FIELD_GET(B_AX_PLE_Q6_MAX_SIZE_MASK, val));
+
+	dump_err_status_dispatcher(rtwdev);
+}
+
+static void rtw89_mac_dump_l0_to_l1(struct rtw89_dev *rtwdev,
+				    enum mac_ax_err_info err)
+{
+	u32 dbg, event;
+
+	dbg = rtw89_read32(rtwdev, R_AX_SER_DBG_INFO);
+	event = FIELD_GET(B_AX_L0_TO_L1_EVENT_MASK, dbg);
+
+	switch (event) {
+	case MAC_AX_L0_TO_L1_RX_QTA_LOST:
+		rtw89_info(rtwdev, "quota lost!\n");
+		rtw89_mac_dump_qta_lost(rtwdev);
+		break;
+	default:
+		break;
+	}
+}
+
+static void rtw89_mac_dump_err_status(struct rtw89_dev *rtwdev,
+				      enum mac_ax_err_info err)
+{
+	u32 dmac_err, cmac_err;
+
+	if (err != MAC_AX_ERR_L1_ERR_DMAC &&
+	    err != MAC_AX_ERR_L0_PROMOTE_TO_L1)
+		return;
+
+	rtw89_info(rtwdev, "--->\nerr=0x%x\n", err);
+	rtw89_info(rtwdev, "R_AX_SER_DBG_INFO =0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_SER_DBG_INFO));
+
+	cmac_err = rtw89_read32(rtwdev, R_AX_CMAC_ERR_ISR);
+	rtw89_info(rtwdev, "R_AX_CMAC_ERR_ISR =0x%08x\n", cmac_err);
+	dmac_err = rtw89_read32(rtwdev, R_AX_DMAC_ERR_ISR);
+	rtw89_info(rtwdev, "R_AX_DMAC_ERR_ISR =0x%08x\n", dmac_err);
+
+	if (dmac_err) {
+		rtw89_info(rtwdev, "R_AX_WDE_ERR_FLAG_CFG =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_WDE_ERR_FLAG_CFG));
+		rtw89_info(rtwdev, "R_AX_PLE_ERR_FLAG_CFG =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PLE_ERR_FLAG_CFG));
+	}
+
+	if (dmac_err & B_AX_WDRLS_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_WDRLS_ERR_IMR =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_WDRLS_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_WDRLS_ERR_ISR =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WDRLS_ERR_ISR));
+	}
+
+	if (dmac_err & B_AX_WSEC_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_SEC_ERR_IMR_ISR =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_DEBUG));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D00 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_ENG_CTRL));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D04 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_MPDU_PROC));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D10 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_CAM_ACCESS));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D14 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_CAM_RDATA));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D18 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_CAM_WDATA));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D20 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_TX_DEBUG));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D24 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_RX_DEBUG));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D28 =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_TRX_PKT_CNT));
+		rtw89_info(rtwdev, "SEC_local_Register 0x9D2C =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_SEC_TRX_BLK_CNT));
+	}
+
+	if (dmac_err & B_AX_MPDU_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_MPDU_TX_ERR_IMR =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_MPDU_TX_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_MPDU_TX_ERR_ISR =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_MPDU_TX_ERR_ISR));
+		rtw89_info(rtwdev, "R_AX_MPDU_RX_ERR_IMR =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_MPDU_RX_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_MPDU_RX_ERR_ISR =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_MPDU_RX_ERR_ISR));
+	}
+
+	if (dmac_err & B_AX_STA_SCHEDULER_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_STA_SCHEDULER_ERR_IMR =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_STA_SCHEDULER_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_STA_SCHEDULER_ERR_ISR= 0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_STA_SCHEDULER_ERR_ISR));
+	}
+
+	if (dmac_err & B_AX_WDE_DLE_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_WDE_ERR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_WDE_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_WDE_ERR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WDE_ERR_ISR));
+		rtw89_info(rtwdev, "R_AX_PLE_ERR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_PLE_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_PLE_ERR_FLAG_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PLE_ERR_FLAG_ISR));
+		dump_err_status_dispatcher(rtwdev);
+	}
+
+	if (dmac_err & B_AX_TXPKTCTRL_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_TXPKTCTL_ERR_IMR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR));
+		rtw89_info(rtwdev, "R_AX_TXPKTCTL_ERR_IMR_ISR_B1=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR_B1));
+	}
+
+	if (dmac_err & B_AX_PLE_DLE_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_WDE_ERR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_WDE_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_WDE_ERR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WDE_ERR_ISR));
+		rtw89_info(rtwdev, "R_AX_PLE_ERR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_PLE_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_PLE_ERR_FLAG_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PLE_ERR_FLAG_ISR));
+		rtw89_info(rtwdev, "R_AX_WD_CPUQ_OP_0=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WD_CPUQ_OP_0));
+		rtw89_info(rtwdev, "R_AX_WD_CPUQ_OP_1=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WD_CPUQ_OP_1));
+		rtw89_info(rtwdev, "R_AX_WD_CPUQ_OP_2=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WD_CPUQ_OP_2));
+		rtw89_info(rtwdev, "R_AX_WD_CPUQ_OP_STATUS=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_WD_CPUQ_OP_STATUS));
+		rtw89_info(rtwdev, "R_AX_PL_CPUQ_OP_0=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PL_CPUQ_OP_0));
+		rtw89_info(rtwdev, "R_AX_PL_CPUQ_OP_1=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PL_CPUQ_OP_1));
+		rtw89_info(rtwdev, "R_AX_PL_CPUQ_OP_2=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PL_CPUQ_OP_2));
+		rtw89_info(rtwdev, "R_AX_PL_CPUQ_OP_STATUS=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PL_CPUQ_OP_STATUS));
+		rtw89_info(rtwdev, "R_AX_RXDMA_PKT_INFO_0=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_RXDMA_PKT_INFO_0));
+		rtw89_info(rtwdev, "R_AX_RXDMA_PKT_INFO_1=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_RXDMA_PKT_INFO_1));
+		rtw89_info(rtwdev, "R_AX_RXDMA_PKT_INFO_2=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_RXDMA_PKT_INFO_2));
+		dump_err_status_dispatcher(rtwdev);
+	}
+
+	if (dmac_err & B_AX_PKTIN_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_PKTIN_ERR_IMR =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_PKTIN_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_PKTIN_ERR_ISR =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PKTIN_ERR_ISR));
+		rtw89_info(rtwdev, "R_AX_PKTIN_ERR_IMR =0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_PKTIN_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_PKTIN_ERR_ISR =0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PKTIN_ERR_ISR));
+	}
+
+	if (dmac_err & B_AX_DISPATCH_ERR_FLAG)
+		dump_err_status_dispatcher(rtwdev);
+
+	if (dmac_err & B_AX_DLE_CPUIO_ERR_FLAG) {
+		rtw89_info(rtwdev, "R_AX_CPUIO_ERR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_CPUIO_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_CPUIO_ERR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_CPUIO_ERR_ISR));
+	}
+
+	if (dmac_err & BIT(11)) {
+		rtw89_info(rtwdev, "R_AX_BBRPT_COM_ERR_IMR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_BBRPT_COM_ERR_IMR_ISR));
+	}
+
+	if (cmac_err & B_AX_SCHEDULE_TOP_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_SCHEDULE_ERR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_SCHEDULE_ERR_IMR));
+		rtw89_info(rtwdev, "R_AX_SCHEDULE_ERR_ISR=0x%04x\n",
+			   rtw89_read16(rtwdev, R_AX_SCHEDULE_ERR_ISR));
+	}
+
+	if (cmac_err & B_AX_PTCL_TOP_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_PTCL_IMR0=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_PTCL_IMR0));
+		rtw89_info(rtwdev, "R_AX_PTCL_ISR0=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PTCL_ISR0));
+	}
+
+	if (cmac_err & B_AX_DMA_TOP_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_DLE_CTRL=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_DLE_CTRL));
+	}
+
+	if (cmac_err & B_AX_PHYINTF_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_PHYINFO_ERR_IMR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PHYINFO_ERR_IMR));
+	}
+
+	if (cmac_err & B_AX_TXPWR_CTRL_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_TXPWR_IMR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_TXPWR_IMR));
+		rtw89_info(rtwdev, "R_AX_TXPWR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_TXPWR_ISR));
+	}
+
+	if (cmac_err & B_AX_WMAC_RX_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_DBGSEL_TRXPTCL=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_DBGSEL_TRXPTCL));
+		rtw89_info(rtwdev, "R_AX_PHYINFO_ERR_ISR=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_PHYINFO_ERR_ISR));
+	}
+
+	if (cmac_err & B_AX_WMAC_TX_ERR_IND) {
+		rtw89_info(rtwdev, "R_AX_TMAC_ERR_IMR_ISR=0x%08x ",
+			   rtw89_read32(rtwdev, R_AX_TMAC_ERR_IMR_ISR));
+		rtw89_info(rtwdev, "R_AX_DBGSEL_TRXPTCL=0x%08x\n",
+			   rtw89_read32(rtwdev, R_AX_DBGSEL_TRXPTCL));
+	}
+
+	rtwdev->hci.ops->dump_err_status(rtwdev);
+
+	if (err == MAC_AX_ERR_L0_PROMOTE_TO_L1)
+		rtw89_mac_dump_l0_to_l1(rtwdev, err);
+
+	rtw89_info(rtwdev, "<---\n");
+}
+
+u32 rtw89_mac_get_err_status(struct rtw89_dev *rtwdev)
+{
+	u32 err;
+	int ret;
+
+	ret = read_poll_timeout(rtw89_read32, err, (err != 0), 1000, 100000,
+				false, rtwdev, R_AX_HALT_C2H_CTRL);
+	if (ret) {
+		rtw89_warn(rtwdev, "Polling FW err status fail\n");
+		return ret;
+	}
+
+	err = rtw89_read32(rtwdev, R_AX_HALT_C2H);
+	rtw89_write32(rtwdev, R_AX_HALT_C2H_CTRL, 0);
+
+	rtw89_fw_st_dbg_dump(rtwdev);
+	rtw89_mac_dump_err_status(rtwdev, err);
+
+	return err;
+}
+EXPORT_SYMBOL(rtw89_mac_get_err_status);
+
+int rtw89_mac_set_err_status(struct rtw89_dev *rtwdev, u32 err)
+{
+	u32 halt;
+	int ret = 0;
+
+	if (err > MAC_AX_SET_ERR_MAX) {
+		rtw89_err(rtwdev, "Bad set-err-status value 0x%08x\n", err);
+		return -EINVAL;
+	}
+
+	ret = read_poll_timeout(rtw89_read32, halt, (halt == 0x0), 1000,
+				100000, false, rtwdev, R_AX_HALT_H2C_CTRL);
+	if (ret) {
+		rtw89_err(rtwdev, "FW doesn't receive previous msg\n");
+		return -EFAULT;
+	}
+
+	rtw89_write32(rtwdev, R_AX_HALT_H2C, err);
+	rtw89_write32(rtwdev, R_AX_HALT_H2C_CTRL, B_AX_HALT_H2C_TRIGGER);
+
+	return 0;
+}
+EXPORT_SYMBOL(rtw89_mac_set_err_status);
+
+const struct rtw89_hfc_prec_cfg rtw_hfc_preccfg_pcie = {
+	2, 40, 0, 0, 1, 0, 0, 0
+};
+
+static int hfc_reset_param(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	struct rtw89_hfc_param_ini param_ini = {NULL};
+	u8 qta_mode = rtwdev->mac.dle_info.qta_mode;
+
+	switch (rtwdev->hci.type) {
+	case RTW89_HCI_TYPE_PCIE:
+		param_ini = rtwdev->chip->hfc_param_ini[qta_mode];
+		param->en = 0;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (param_ini.pub_cfg)
+		param->pub_cfg = *param_ini.pub_cfg;
+
+	if (param_ini.prec_cfg) {
+		param->prec_cfg = *param_ini.prec_cfg;
+		rtwdev->hal.sw_amsdu_max_size =
+				param->prec_cfg.wp_ch07_prec * HFC_PAGE_UNIT;
+	}
+
+	if (param_ini.ch_cfg)
+		param->ch_cfg = param_ini.ch_cfg;
+
+	memset(&param->ch_info, 0, sizeof(param->ch_info));
+	memset(&param->pub_info, 0, sizeof(param->pub_info));
+	param->mode = param_ini.mode;
+
+	return 0;
+}
+
+static int hfc_ch_cfg_chk(struct rtw89_dev *rtwdev, u8 ch)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	const struct rtw89_hfc_ch_cfg *ch_cfg = param->ch_cfg;
+	const struct rtw89_hfc_pub_cfg *pub_cfg = &param->pub_cfg;
+	const struct rtw89_hfc_prec_cfg *prec_cfg = &param->prec_cfg;
+
+	if (ch >= RTW89_DMA_CH_NUM)
+		return -EINVAL;
+
+	if ((ch_cfg[ch].min && ch_cfg[ch].min < prec_cfg->ch011_prec) ||
+	    ch_cfg[ch].max > pub_cfg->pub_max)
+		return -EINVAL;
+	if (ch_cfg[ch].grp >= grp_num)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int hfc_pub_info_chk(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	const struct rtw89_hfc_pub_cfg *cfg = &param->pub_cfg;
+	struct rtw89_hfc_pub_info *info = &param->pub_info;
+
+	if (info->g0_used + info->g1_used + info->pub_aval != cfg->pub_max) {
+		if (rtwdev->chip->chip_id == RTL8852A)
+			return 0;
+		else
+			return -EFAULT;
+	}
+
+	return 0;
+}
+
+static int hfc_pub_cfg_chk(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	const struct rtw89_hfc_pub_cfg *pub_cfg = &param->pub_cfg;
+
+	if (pub_cfg->grp0 + pub_cfg->grp1 != pub_cfg->pub_max)
+		return 0;
+
+	return 0;
+}
+
+static int hfc_ch_ctrl(struct rtw89_dev *rtwdev, u8 ch)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	const struct rtw89_hfc_ch_cfg *cfg = param->ch_cfg;
+	int ret = 0;
+	u32 val = 0;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	ret = hfc_ch_cfg_chk(rtwdev, ch);
+	if (ret)
+		return ret;
+
+	if (ch > RTW89_DMA_B1HI)
+		return -EINVAL;
+
+	val = u32_encode_bits(cfg[ch].min, B_AX_MIN_PG_MASK) |
+	      u32_encode_bits(cfg[ch].max, B_AX_MAX_PG_MASK) |
+	      (cfg[ch].grp ? B_AX_GRP : 0);
+	rtw89_write32(rtwdev, R_AX_ACH0_PAGE_CTRL + ch * 4, val);
+
+	return 0;
+}
+
+static int hfc_upd_ch_info(struct rtw89_dev *rtwdev, u8 ch)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	struct rtw89_hfc_ch_info *info = param->ch_info;
+	const struct rtw89_hfc_ch_cfg *cfg = param->ch_cfg;
+	u32 val;
+	u32 ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	if (ch > RTW89_DMA_H2C)
+		return -EINVAL;
+
+	val = rtw89_read32(rtwdev, R_AX_ACH0_PAGE_INFO + ch * 4);
+	info[ch].aval = u32_get_bits(val, B_AX_AVAL_PG_MASK);
+	if (ch < RTW89_DMA_H2C)
+		info[ch].used = u32_get_bits(val, B_AX_USE_PG_MASK);
+	else
+		info[ch].used = cfg[ch].min - info[ch].aval;
+
+	return 0;
+}
+
+static int hfc_pub_ctrl(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_hfc_pub_cfg *cfg = &rtwdev->mac.hfc_param.pub_cfg;
+	u32 val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	ret = hfc_pub_cfg_chk(rtwdev);
+	if (ret)
+		return ret;
+
+	val = u32_encode_bits(cfg->grp0, B_AX_PUBPG_G0_MASK) |
+	      u32_encode_bits(cfg->grp1, B_AX_PUBPG_G1_MASK);
+	rtw89_write32(rtwdev, R_AX_PUB_PAGE_CTRL1, val);
+
+	val = u32_encode_bits(cfg->wp_thrd, B_AX_WP_THRD_MASK);
+	rtw89_write32(rtwdev, R_AX_WP_PAGE_CTRL2, val);
+
+	return 0;
+}
+
+static int hfc_upd_mix_info(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	struct rtw89_hfc_pub_cfg *pub_cfg = &param->pub_cfg;
+	struct rtw89_hfc_prec_cfg *prec_cfg = &param->prec_cfg;
+	struct rtw89_hfc_pub_info *info = &param->pub_info;
+	u32 val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	val = rtw89_read32(rtwdev, R_AX_PUB_PAGE_INFO1);
+	info->g0_used = u32_get_bits(val, B_AX_G0_USE_PG_MASK);
+	info->g1_used = u32_get_bits(val, B_AX_G1_USE_PG_MASK);
+	val = rtw89_read32(rtwdev, R_AX_PUB_PAGE_INFO3);
+	info->g0_aval = u32_get_bits(val, B_AX_G0_AVAL_PG_MASK);
+	info->g1_aval = u32_get_bits(val, B_AX_G1_AVAL_PG_MASK);
+	info->pub_aval =
+		u32_get_bits(rtw89_read32(rtwdev, R_AX_PUB_PAGE_INFO2),
+			     B_AX_PUB_AVAL_PG_MASK);
+	info->wp_aval =
+		u32_get_bits(rtw89_read32(rtwdev, R_AX_WP_PAGE_INFO1),
+			     B_AX_WP_AVAL_PG_MASK);
+
+	val = rtw89_read32(rtwdev, R_AX_HCI_FC_CTRL);
+	param->en = val & B_AX_HCI_FC_EN ? 1 : 0;
+	param->h2c_en = val & B_AX_HCI_FC_CH12_EN ? 1 : 0;
+	param->mode = u32_get_bits(val, B_AX_HCI_FC_MODE_MASK);
+	prec_cfg->ch011_full_cond =
+		u32_get_bits(val, B_AX_HCI_FC_WD_FULL_COND_MASK);
+	prec_cfg->h2c_full_cond =
+		u32_get_bits(val, B_AX_HCI_FC_CH12_FULL_COND_MASK);
+	prec_cfg->wp_ch07_full_cond =
+		u32_get_bits(val, B_AX_HCI_FC_WP_CH07_FULL_COND_MASK);
+	prec_cfg->wp_ch811_full_cond =
+		u32_get_bits(val, B_AX_HCI_FC_WP_CH811_FULL_COND_MASK);
+
+	val = rtw89_read32(rtwdev, R_AX_CH_PAGE_CTRL);
+	prec_cfg->ch011_prec = u32_get_bits(val, B_AX_PREC_PAGE_CH011_MASK);
+	prec_cfg->h2c_prec = u32_get_bits(val, B_AX_PREC_PAGE_CH12_MASK);
+
+	val = rtw89_read32(rtwdev, R_AX_PUB_PAGE_CTRL2);
+	pub_cfg->pub_max = u32_get_bits(val, B_AX_PUBPG_ALL_MASK);
+
+	val = rtw89_read32(rtwdev, R_AX_WP_PAGE_CTRL1);
+	prec_cfg->wp_ch07_prec = u32_get_bits(val, B_AX_PREC_PAGE_WP_CH07_MASK);
+	prec_cfg->wp_ch811_prec = u32_get_bits(val, B_AX_PREC_PAGE_WP_CH811_MASK);
+
+	val = rtw89_read32(rtwdev, R_AX_WP_PAGE_CTRL2);
+	pub_cfg->wp_thrd = u32_get_bits(val, B_AX_WP_THRD_MASK);
+
+	val = rtw89_read32(rtwdev, R_AX_PUB_PAGE_CTRL1);
+	pub_cfg->grp0 = u32_get_bits(val, B_AX_PUBPG_G0_MASK);
+	pub_cfg->grp1 = u32_get_bits(val, B_AX_PUBPG_G1_MASK);
+
+	ret = hfc_pub_info_chk(rtwdev);
+	if (param->en && ret)
+		return ret;
+
+	return 0;
+}
+
+static void hfc_h2c_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	const struct rtw89_hfc_prec_cfg *prec_cfg = &param->prec_cfg;
+	u32 val;
+
+	val = u32_encode_bits(prec_cfg->h2c_prec, B_AX_PREC_PAGE_CH12_MASK);
+	rtw89_write32(rtwdev, R_AX_CH_PAGE_CTRL, val);
+
+	rtw89_write32_mask(rtwdev, R_AX_HCI_FC_CTRL,
+			   B_AX_HCI_FC_CH12_FULL_COND_MASK,
+			   prec_cfg->h2c_full_cond);
+}
+
+static void hfc_mix_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	const struct rtw89_hfc_pub_cfg *pub_cfg = &param->pub_cfg;
+	const struct rtw89_hfc_prec_cfg *prec_cfg = &param->prec_cfg;
+	u32 val;
+
+	val = u32_encode_bits(prec_cfg->ch011_prec, B_AX_PREC_PAGE_CH011_MASK) |
+	      u32_encode_bits(prec_cfg->h2c_prec, B_AX_PREC_PAGE_CH12_MASK);
+	rtw89_write32(rtwdev, R_AX_CH_PAGE_CTRL, val);
+
+	val = u32_encode_bits(pub_cfg->pub_max, B_AX_PUBPG_ALL_MASK);
+	rtw89_write32(rtwdev, R_AX_PUB_PAGE_CTRL2, val);
+
+	val = u32_encode_bits(prec_cfg->wp_ch07_prec,
+			      B_AX_PREC_PAGE_WP_CH07_MASK) |
+	      u32_encode_bits(prec_cfg->wp_ch811_prec,
+			      B_AX_PREC_PAGE_WP_CH811_MASK);
+	rtw89_write32(rtwdev, R_AX_WP_PAGE_CTRL1, val);
+
+	val = u32_replace_bits(rtw89_read32(rtwdev, R_AX_HCI_FC_CTRL),
+			       param->mode, B_AX_HCI_FC_MODE_MASK);
+	val = u32_replace_bits(val, prec_cfg->ch011_full_cond,
+			       B_AX_HCI_FC_WD_FULL_COND_MASK);
+	val = u32_replace_bits(val, prec_cfg->h2c_full_cond,
+			       B_AX_HCI_FC_CH12_FULL_COND_MASK);
+	val = u32_replace_bits(val, prec_cfg->wp_ch07_full_cond,
+			       B_AX_HCI_FC_WP_CH07_FULL_COND_MASK);
+	val = u32_replace_bits(val, prec_cfg->wp_ch811_full_cond,
+			       B_AX_HCI_FC_WP_CH811_FULL_COND_MASK);
+	rtw89_write32(rtwdev, R_AX_HCI_FC_CTRL, val);
+}
+
+static void hfc_func_en(struct rtw89_dev *rtwdev, bool en, bool h2c_en)
+{
+	struct rtw89_hfc_param *param = &rtwdev->mac.hfc_param;
+	u32 val;
+
+	val = rtw89_read32(rtwdev, R_AX_HCI_FC_CTRL);
+	param->en = en;
+	param->h2c_en = h2c_en;
+	val = en ? (val | B_AX_HCI_FC_EN) : (val & ~B_AX_HCI_FC_EN);
+	val = h2c_en ? (val | B_AX_HCI_FC_CH12_EN) :
+			 (val & ~B_AX_HCI_FC_CH12_EN);
+	rtw89_write32(rtwdev, R_AX_HCI_FC_CTRL, val);
+}
+
+static int hfc_init(struct rtw89_dev *rtwdev, bool reset, bool en, bool h2c_en)
+{
+	u8 ch;
+	u32 ret = 0;
+
+	if (reset)
+		ret = hfc_reset_param(rtwdev);
+	if (ret)
+		return ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	hfc_func_en(rtwdev, false, false);
+
+	if (!en && h2c_en) {
+		hfc_h2c_cfg(rtwdev);
+		hfc_func_en(rtwdev, en, h2c_en);
+		return ret;
+	}
+
+	for (ch = RTW89_DMA_ACH0; ch < RTW89_DMA_H2C; ch++) {
+		ret = hfc_ch_ctrl(rtwdev, ch);
+		if (ret)
+			return ret;
+	}
+
+	ret = hfc_pub_ctrl(rtwdev);
+	if (ret)
+		return ret;
+
+	hfc_mix_cfg(rtwdev);
+	if (en || h2c_en) {
+		hfc_func_en(rtwdev, en, h2c_en);
+		udelay(10);
+	}
+	for (ch = RTW89_DMA_ACH0; ch < RTW89_DMA_H2C; ch++) {
+		ret = hfc_upd_ch_info(rtwdev, ch);
+		if (ret)
+			return ret;
+	}
+	ret = hfc_upd_mix_info(rtwdev);
+
+	return ret;
+}
+
+#define PWR_POLL_CNT	2000
+static int pwr_cmd_poll(struct rtw89_dev *rtwdev,
+			const struct rtw89_pwr_cfg *cfg)
+{
+	u8 val = 0;
+	int ret;
+	u32 addr = cfg->base == PWR_INTF_MSK_SDIO ?
+		   cfg->addr | SDIO_LOCAL_BASE_ADDR : cfg->addr;
+
+	ret = read_poll_timeout(rtw89_read8, val, !((val ^ cfg->val) & cfg->msk),
+				1000, 1000 * PWR_POLL_CNT, false, rtwdev, addr);
+
+	if (!ret)
+		return 0;
+
+	rtw89_warn(rtwdev, "[ERR] Polling timeout\n");
+	rtw89_warn(rtwdev, "[ERR] addr: %X, %X\n", addr, cfg->addr);
+	rtw89_warn(rtwdev, "[ERR] val: %X, %X\n", val, cfg->val);
+
+	return -EBUSY;
+}
+
+static int rtw89_mac_sub_pwr_seq(struct rtw89_dev *rtwdev, u8 cv_msk,
+				 u8 intf_msk, const struct rtw89_pwr_cfg *cfg)
+{
+	const struct rtw89_pwr_cfg *cur_cfg;
+	u32 addr;
+	u8 val;
+
+	for (cur_cfg = cfg; cur_cfg->cmd != PWR_CMD_END; cur_cfg++) {
+		if (!(cur_cfg->intf_msk & intf_msk) ||
+		    !(cur_cfg->cv_msk & cv_msk))
+			continue;
+
+		switch (cur_cfg->cmd) {
+		case PWR_CMD_WRITE:
+			addr = cur_cfg->addr;
+
+			if (cur_cfg->base == PWR_BASE_SDIO)
+				addr |= SDIO_LOCAL_BASE_ADDR;
+
+			val = rtw89_read8(rtwdev, addr);
+			val &= ~(cur_cfg->msk);
+			val |= (cur_cfg->val & cur_cfg->msk);
+
+			rtw89_write8(rtwdev, addr, val);
+			break;
+		case PWR_CMD_POLL:
+			if (pwr_cmd_poll(rtwdev, cur_cfg))
+				return -EBUSY;
+			break;
+		case PWR_CMD_DELAY:
+			if (cur_cfg->val == PWR_DELAY_US)
+				udelay(cur_cfg->addr);
+			else
+				fsleep(cur_cfg->addr * 1000);
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int rtw89_mac_pwr_seq(struct rtw89_dev *rtwdev,
+			     const struct rtw89_pwr_cfg * const *cfg_seq)
+{
+	int ret;
+
+	for (; *cfg_seq; cfg_seq++) {
+		ret = rtw89_mac_sub_pwr_seq(rtwdev, BIT(rtwdev->hal.cv),
+					    PWR_INTF_MSK_PCIE, *cfg_seq);
+		if (ret)
+			return -EBUSY;
+	}
+
+	return 0;
+}
+
+static enum rtw89_rpwm_req_pwr_state
+rtw89_mac_get_req_pwr_state(struct rtw89_dev *rtwdev)
+{
+	enum rtw89_rpwm_req_pwr_state state;
+
+	switch (rtwdev->ps_mode) {
+	case RTW89_PS_MODE_RFOFF:
+		state = RTW89_MAC_RPWM_REQ_PWR_STATE_BAND0_RFOFF;
+		break;
+	case RTW89_PS_MODE_CLK_GATED:
+		state = RTW89_MAC_RPWM_REQ_PWR_STATE_CLK_GATED;
+		break;
+	case RTW89_PS_MODE_PWR_GATED:
+		state = RTW89_MAC_RPWM_REQ_PWR_STATE_PWR_GATED;
+		break;
+	default:
+		state = RTW89_MAC_RPWM_REQ_PWR_STATE_ACTIVE;
+		break;
+	}
+	return state;
+}
+
+static void rtw89_mac_send_rpwm(struct rtw89_dev *rtwdev,
+				enum rtw89_rpwm_req_pwr_state req_pwr_state)
+{
+	u16 request;
+
+	request = rtw89_read16(rtwdev, R_AX_RPWM);
+	request ^= request | PS_RPWM_TOGGLE;
+
+	rtwdev->mac.rpwm_seq_num = (rtwdev->mac.rpwm_seq_num + 1) &
+				   RPWM_SEQ_NUM_MAX;
+	request |= FIELD_PREP(PS_RPWM_SEQ_NUM, rtwdev->mac.rpwm_seq_num);
+
+	request |= req_pwr_state;
+
+	if (req_pwr_state < RTW89_MAC_RPWM_REQ_PWR_STATE_CLK_GATED)
+		request |= PS_RPWM_ACK;
+
+	rtw89_write16(rtwdev, rtwdev->hci.rpwm_addr, request);
+}
+
+static int rtw89_mac_check_cpwm_state(struct rtw89_dev *rtwdev,
+				      enum rtw89_rpwm_req_pwr_state req_pwr_state)
+{
+	bool request_deep_mode;
+	bool in_deep_mode;
+	u8 rpwm_req_num;
+	u8 cpwm_rsp_seq;
+	u8 cpwm_seq;
+	u8 cpwm_status;
+
+	if (req_pwr_state >= RTW89_MAC_RPWM_REQ_PWR_STATE_CLK_GATED)
+		request_deep_mode = true;
+	else
+		request_deep_mode = false;
+
+	if (rtw89_read32_mask(rtwdev, R_AX_LDM, B_AX_EN_32K))
+		in_deep_mode = true;
+	else
+		in_deep_mode = false;
+
+	if (request_deep_mode != in_deep_mode)
+		return -EPERM;
+
+	if (request_deep_mode)
+		return 0;
+
+	rpwm_req_num = rtwdev->mac.rpwm_seq_num;
+	cpwm_rsp_seq = rtw89_read16_mask(rtwdev, R_AX_CPWM,
+					 PS_CPWM_RSP_SEQ_NUM);
+
+	if (rpwm_req_num != cpwm_rsp_seq)
+		return -EPERM;
+
+	rtwdev->mac.cpwm_seq_num = (rtwdev->mac.cpwm_seq_num + 1) &
+				    CPWM_SEQ_NUM_MAX;
+
+	cpwm_seq = rtw89_read16_mask(rtwdev, R_AX_CPWM, PS_CPWM_SEQ_NUM);
+	if (cpwm_seq != rtwdev->mac.cpwm_seq_num)
+		return -EPERM;
+
+	cpwm_status = rtw89_read16_mask(rtwdev, R_AX_CPWM, PS_CPWM_STATE);
+	if (cpwm_status != req_pwr_state)
+		return -EPERM;
+
+	return 0;
+}
+
+void rtw89_mac_power_mode_change(struct rtw89_dev *rtwdev, bool enter)
+{
+	enum rtw89_rpwm_req_pwr_state state;
+	int ret;
+
+	if (enter)
+		state = rtw89_mac_get_req_pwr_state(rtwdev);
+	else
+		state = RTW89_MAC_RPWM_REQ_PWR_STATE_ACTIVE;
+
+	rtw89_mac_send_rpwm(rtwdev, state);
+	ret = read_poll_timeout_atomic(rtw89_mac_check_cpwm_state, ret, !ret,
+				       1000, 15000, false, rtwdev, state);
+	if (ret)
+		rtw89_err(rtwdev, "firmware failed to ack for %s ps mode\n",
+			  enter ? "entering" : "leaving");
+}
+
+static int rtw89_mac_power_switch(struct rtw89_dev *rtwdev, bool on)
+{
+#define PWR_ACT 1
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const struct rtw89_pwr_cfg * const *cfg_seq;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	int ret;
+	u8 val;
+
+	if (on)
+		cfg_seq = chip->pwr_on_seq;
+	else
+		cfg_seq = chip->pwr_off_seq;
+
+	if (test_bit(RTW89_FLAG_FW_RDY, rtwdev->flags))
+		__rtw89_leave_ps_mode(rtwdev);
+
+	val = rtw89_read32_mask(rtwdev, R_AX_IC_PWR_STATE, B_AX_WLMAC_PWR_STE_MASK);
+	if (on && val == PWR_ACT) {
+		rtw89_err(rtwdev, "MAC has already powered on\n");
+		return -EBUSY;
+	}
+
+	ret = rtw89_mac_pwr_seq(rtwdev, cfg_seq);
+	if (ret)
+		return ret;
+
+	if (on) {
+		set_bit(RTW89_FLAG_POWERON, rtwdev->flags);
+		rtw89_write8(rtwdev, R_AX_SCOREBOARD + 3, MAC_AX_NOTIFY_TP_MAJOR);
+	} else {
+		clear_bit(RTW89_FLAG_POWERON, rtwdev->flags);
+		clear_bit(RTW89_FLAG_FW_RDY, rtwdev->flags);
+		rtw89_write8(rtwdev, R_AX_SCOREBOARD + 3, MAC_AX_NOTIFY_PWR_MAJOR);
+		hal->current_channel = 0;
+	}
+
+	return 0;
+#undef PWR_ACT
+}
+
+void rtw89_mac_pwr_off(struct rtw89_dev *rtwdev)
+{
+	rtw89_mac_power_switch(rtwdev, false);
+}
+
+static int cmac_func_en(struct rtw89_dev *rtwdev, u8 mac_idx, bool en)
+{
+	u32 func_en = 0;
+	u32 ck_en = 0;
+	u32 c1pc_en = 0;
+	u32 addrl_func_en[] = {R_AX_CMAC_FUNC_EN, R_AX_CMAC_FUNC_EN_C1};
+	u32 addrl_ck_en[] = {R_AX_CK_EN, R_AX_CK_EN_C1};
+
+	func_en = B_AX_CMAC_EN | B_AX_CMAC_TXEN | B_AX_CMAC_RXEN |
+			B_AX_PHYINTF_EN | B_AX_CMAC_DMA_EN | B_AX_PTCLTOP_EN |
+			B_AX_SCHEDULER_EN | B_AX_TMAC_EN | B_AX_RMAC_EN;
+	ck_en = B_AX_CMAC_CKEN | B_AX_PHYINTF_CKEN | B_AX_CMAC_DMA_CKEN |
+		      B_AX_PTCLTOP_CKEN | B_AX_SCHEDULER_CKEN | B_AX_TMAC_CKEN |
+		      B_AX_RMAC_CKEN;
+	c1pc_en = B_AX_R_SYM_WLCMAC1_PC_EN |
+			B_AX_R_SYM_WLCMAC1_P1_PC_EN |
+			B_AX_R_SYM_WLCMAC1_P2_PC_EN |
+			B_AX_R_SYM_WLCMAC1_P3_PC_EN |
+			B_AX_R_SYM_WLCMAC1_P4_PC_EN;
+
+	if (en) {
+		if (mac_idx == RTW89_MAC_1) {
+			rtw89_write32_set(rtwdev, R_AX_AFE_CTRL1, c1pc_en);
+			rtw89_write32_clr(rtwdev, R_AX_SYS_ISO_CTRL_EXTEND,
+					  B_AX_R_SYM_ISO_CMAC12PP);
+			rtw89_write32_set(rtwdev, R_AX_SYS_ISO_CTRL_EXTEND,
+					  B_AX_CMAC1_FEN);
+		}
+		rtw89_write32_set(rtwdev, addrl_ck_en[mac_idx], ck_en);
+		rtw89_write32_set(rtwdev, addrl_func_en[mac_idx], func_en);
+	} else {
+		rtw89_write32_clr(rtwdev, addrl_func_en[mac_idx], func_en);
+		rtw89_write32_clr(rtwdev, addrl_ck_en[mac_idx], ck_en);
+		if (mac_idx == RTW89_MAC_1) {
+			rtw89_write32_clr(rtwdev, R_AX_SYS_ISO_CTRL_EXTEND,
+					  B_AX_CMAC1_FEN);
+			rtw89_write32_set(rtwdev, R_AX_SYS_ISO_CTRL_EXTEND,
+					  B_AX_R_SYM_ISO_CMAC12PP);
+			rtw89_write32_clr(rtwdev, R_AX_AFE_CTRL1, c1pc_en);
+		}
+	}
+
+	return 0;
+}
+
+static int dmac_func_en(struct rtw89_dev *rtwdev)
+{
+	u32 val32;
+	u32 ret = 0;
+
+	val32 = (B_AX_MAC_FUNC_EN | B_AX_DMAC_FUNC_EN | B_AX_MAC_SEC_EN |
+		 B_AX_DISPATCHER_EN | B_AX_DLE_CPUIO_EN | B_AX_PKT_IN_EN |
+		 B_AX_DMAC_TBL_EN | B_AX_PKT_BUF_EN | B_AX_STA_SCH_EN |
+		 B_AX_TXPKT_CTRL_EN | B_AX_WD_RLS_EN | B_AX_MPDU_PROC_EN);
+	rtw89_write32(rtwdev, R_AX_DMAC_FUNC_EN, val32);
+
+	val32 = (B_AX_MAC_SEC_CLK_EN | B_AX_DISPATCHER_CLK_EN |
+		 B_AX_DLE_CPUIO_CLK_EN | B_AX_PKT_IN_CLK_EN |
+		 B_AX_STA_SCH_CLK_EN | B_AX_TXPKT_CTRL_CLK_EN |
+		 B_AX_WD_RLS_CLK_EN);
+	rtw89_write32(rtwdev, R_AX_DMAC_CLK_EN, val32);
+
+	return ret;
+}
+
+static int chip_func_en(struct rtw89_dev *rtwdev)
+{
+	rtw89_write32_set(rtwdev, R_AX_SPSLDO_ON_CTRL0, B_AX_OCP_L1_MASK);
+
+	return 0;
+}
+
+static int rtw89_mac_sys_init(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = dmac_func_en(rtwdev);
+	if (ret)
+		return ret;
+
+	ret = cmac_func_en(rtwdev, 0, true);
+	if (ret)
+		return ret;
+
+	ret = chip_func_en(rtwdev);
+	if (ret)
+		return ret;
+
+	return ret;
+}
+
+/* PCIE 64 */
+const struct rtw89_dle_size wde_size0 = {
+	RTW89_WDE_PG_64, 4095, 1,
+};
+
+/* DLFW */
+const struct rtw89_dle_size wde_size4 = {
+	RTW89_WDE_PG_64, 0, 4096,
+};
+
+/* PCIE */
+const struct rtw89_dle_size ple_size0 = {
+	RTW89_PLE_PG_128, 1520, 16,
+};
+
+/* DLFW */
+const struct rtw89_dle_size ple_size4 = {
+	RTW89_PLE_PG_128, 64, 1472,
+};
+
+/* PCIE 64 */
+const struct rtw89_wde_quota wde_qt0 = {
+	3792, 196, 0, 107,
+};
+
+/* DLFW */
+const struct rtw89_wde_quota wde_qt4 = {
+	0, 0, 0, 0,
+};
+
+/* PCIE SCC */
+const struct rtw89_ple_quota ple_qt4 = {
+	264, 0, 16, 20, 26, 13, 356, 0, 32, 40, 8,
+};
+
+/* PCIE SCC */
+const struct rtw89_ple_quota ple_qt5 = {
+	264, 0, 32, 20, 64, 13, 1101, 0, 64, 128, 120,
+};
+
+/* DLFW */
+const struct rtw89_ple_quota ple_qt13 = {
+	0, 0, 16, 48, 0, 0, 0, 0, 0, 0, 0
+};
+
+static const struct rtw89_dle_mem *get_dle_mem_cfg(struct rtw89_dev *rtwdev,
+						   enum rtw89_qta_mode mode)
+{
+	struct rtw89_mac_info *mac = &rtwdev->mac;
+	const struct rtw89_dle_mem *cfg;
+
+	cfg = &rtwdev->chip->dle_mem[mode];
+	if (!cfg)
+		return NULL;
+
+	if (cfg->mode != mode) {
+		rtw89_warn(rtwdev, "qta mode unmatch!\n");
+		return NULL;
+	}
+
+	mac->dle_info.wde_pg_size = cfg->wde_size->pge_size;
+	mac->dle_info.ple_pg_size = cfg->ple_size->pge_size;
+	mac->dle_info.qta_mode = mode;
+	mac->dle_info.c0_rx_qta = cfg->ple_min_qt->cma0_dma;
+	mac->dle_info.c1_rx_qta = cfg->ple_min_qt->cma1_dma;
+
+	return cfg;
+}
+
+static inline u32 dle_used_size(const struct rtw89_dle_size *wde,
+				const struct rtw89_dle_size *ple)
+{
+	return wde->pge_size * (wde->lnk_pge_num + wde->unlnk_pge_num) +
+	       ple->pge_size * (ple->lnk_pge_num + ple->unlnk_pge_num);
+}
+
+static void dle_func_en(struct rtw89_dev *rtwdev, bool enable)
+{
+	if (enable)
+		rtw89_write32_set(rtwdev, R_AX_DMAC_FUNC_EN,
+				  B_AX_DLE_WDE_EN | B_AX_DLE_PLE_EN);
+	else
+		rtw89_write32_clr(rtwdev, R_AX_DMAC_FUNC_EN,
+				  B_AX_DLE_WDE_EN | B_AX_DLE_PLE_EN);
+}
+
+static void dle_clk_en(struct rtw89_dev *rtwdev, bool enable)
+{
+	if (enable)
+		rtw89_write32_set(rtwdev, R_AX_DMAC_CLK_EN,
+				  B_AX_DLE_WDE_CLK_EN | B_AX_DLE_PLE_CLK_EN);
+	else
+		rtw89_write32_clr(rtwdev, R_AX_DMAC_CLK_EN,
+				  B_AX_DLE_WDE_CLK_EN | B_AX_DLE_PLE_CLK_EN);
+}
+
+static int dle_mix_cfg(struct rtw89_dev *rtwdev, const struct rtw89_dle_mem *cfg)
+{
+	const struct rtw89_dle_size *size_cfg;
+	u32 val;
+	u8 bound = 0;
+
+	val = rtw89_read32(rtwdev, R_AX_WDE_PKTBUF_CFG);
+	size_cfg = cfg->wde_size;
+
+	switch (size_cfg->pge_size) {
+	default:
+	case RTW89_WDE_PG_64:
+		val = u32_replace_bits(val, S_AX_WDE_PAGE_SEL_64,
+				       B_AX_WDE_PAGE_SEL_MASK);
+		break;
+	case RTW89_WDE_PG_128:
+		val = u32_replace_bits(val, S_AX_WDE_PAGE_SEL_128,
+				       B_AX_WDE_PAGE_SEL_MASK);
+		break;
+	case RTW89_WDE_PG_256:
+		rtw89_err(rtwdev, "[ERR]WDE DLE doesn't support 256 byte!\n");
+		return -EINVAL;
+	}
+
+	val = u32_replace_bits(val, bound, B_AX_WDE_START_BOUND_MASK);
+	val = u32_replace_bits(val, size_cfg->lnk_pge_num,
+			       B_AX_WDE_FREE_PAGE_NUM_MASK);
+	rtw89_write32(rtwdev, R_AX_WDE_PKTBUF_CFG, val);
+
+	val = rtw89_read32(rtwdev, R_AX_PLE_PKTBUF_CFG);
+	bound = (size_cfg->lnk_pge_num + size_cfg->unlnk_pge_num)
+				* size_cfg->pge_size / DLE_BOUND_UNIT;
+	size_cfg = cfg->ple_size;
+
+	switch (size_cfg->pge_size) {
+	default:
+	case RTW89_PLE_PG_64:
+		rtw89_err(rtwdev, "[ERR]PLE DLE doesn't support 64 byte!\n");
+		return -EINVAL;
+	case RTW89_PLE_PG_128:
+		val = u32_replace_bits(val, S_AX_PLE_PAGE_SEL_128,
+				       B_AX_PLE_PAGE_SEL_MASK);
+		break;
+	case RTW89_PLE_PG_256:
+		val = u32_replace_bits(val, S_AX_PLE_PAGE_SEL_256,
+				       B_AX_PLE_PAGE_SEL_MASK);
+		break;
+	}
+
+	val = u32_replace_bits(val, bound, B_AX_PLE_START_BOUND_MASK);
+	val = u32_replace_bits(val, size_cfg->lnk_pge_num,
+			       B_AX_PLE_FREE_PAGE_NUM_MASK);
+	rtw89_write32(rtwdev, R_AX_PLE_PKTBUF_CFG, val);
+
+	return 0;
+}
+
+#define INVALID_QT_WCPU U16_MAX
+#define SET_QUOTA_VAL(_min_x, _max_x, _module, _idx)			\
+	do {								\
+		val = ((_min_x) &					\
+		       B_AX_ ## _module ## _MIN_SIZE_MASK) |		\
+		      (((_max_x) << 16) &				\
+		       B_AX_ ## _module ## _MAX_SIZE_MASK);		\
+		rtw89_write32(rtwdev,					\
+			      R_AX_ ## _module ## _QTA ## _idx ## _CFG,	\
+			      val);					\
+	} while (0)
+#define SET_QUOTA(_x, _module, _idx)					\
+	SET_QUOTA_VAL(min_cfg->_x, max_cfg->_x, _module, _idx)
+
+static void wde_quota_cfg(struct rtw89_dev *rtwdev,
+			  const struct rtw89_wde_quota *min_cfg,
+			  const struct rtw89_wde_quota *max_cfg,
+			  u16 ext_wde_min_qt_wcpu)
+{
+	u16 min_qt_wcpu = ext_wde_min_qt_wcpu != INVALID_QT_WCPU ?
+			  ext_wde_min_qt_wcpu : min_cfg->wcpu;
+	u32 val;
+
+	SET_QUOTA(hif, WDE, 0);
+	SET_QUOTA_VAL(min_qt_wcpu, max_cfg->wcpu, WDE, 1);
+	SET_QUOTA(pkt_in, WDE, 3);
+	SET_QUOTA(cpu_io, WDE, 4);
+}
+
+static void ple_quota_cfg(struct rtw89_dev *rtwdev,
+			  const struct rtw89_ple_quota *min_cfg,
+			  const struct rtw89_ple_quota *max_cfg)
+{
+	u32 val;
+
+	SET_QUOTA(cma0_tx, PLE, 0);
+	SET_QUOTA(cma1_tx, PLE, 1);
+	SET_QUOTA(c2h, PLE, 2);
+	SET_QUOTA(h2c, PLE, 3);
+	SET_QUOTA(wcpu, PLE, 4);
+	SET_QUOTA(mpdu_proc, PLE, 5);
+	SET_QUOTA(cma0_dma, PLE, 6);
+	SET_QUOTA(cma1_dma, PLE, 7);
+	SET_QUOTA(bb_rpt, PLE, 8);
+	SET_QUOTA(wd_rel, PLE, 9);
+	SET_QUOTA(cpu_io, PLE, 10);
+}
+
+#undef SET_QUOTA
+
+static void dle_quota_cfg(struct rtw89_dev *rtwdev,
+			  const struct rtw89_dle_mem *cfg,
+			  u16 ext_wde_min_qt_wcpu)
+{
+	wde_quota_cfg(rtwdev, cfg->wde_min_qt, cfg->wde_max_qt, ext_wde_min_qt_wcpu);
+	ple_quota_cfg(rtwdev, cfg->ple_min_qt, cfg->ple_max_qt);
+}
+
+static int dle_init(struct rtw89_dev *rtwdev, enum rtw89_qta_mode mode,
+		    enum rtw89_qta_mode ext_mode)
+{
+	const struct rtw89_dle_mem *cfg, *ext_cfg;
+	u16 ext_wde_min_qt_wcpu = INVALID_QT_WCPU;
+	int ret = 0;
+	u32 ini;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	cfg = get_dle_mem_cfg(rtwdev, mode);
+	if (!cfg) {
+		rtw89_err(rtwdev, "[ERR]get_dle_mem_cfg\n");
+		ret = -EINVAL;
+		goto error;
+	}
+
+	if (mode == RTW89_QTA_DLFW) {
+		ext_cfg = get_dle_mem_cfg(rtwdev, ext_mode);
+		if (!ext_cfg) {
+			rtw89_err(rtwdev, "[ERR]get_dle_ext_mem_cfg %d\n",
+				  ext_mode);
+			ret = -EINVAL;
+			goto error;
+		}
+		ext_wde_min_qt_wcpu = ext_cfg->wde_min_qt->wcpu;
+	}
+
+	if (dle_used_size(cfg->wde_size, cfg->ple_size) != rtwdev->chip->fifo_size) {
+		rtw89_err(rtwdev, "[ERR]wd/dle mem cfg\n");
+		ret = -EINVAL;
+		goto error;
+	}
+
+	dle_func_en(rtwdev, false);
+	dle_clk_en(rtwdev, true);
+
+	ret = dle_mix_cfg(rtwdev, cfg);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] dle mix cfg\n");
+		goto error;
+	}
+	dle_quota_cfg(rtwdev, cfg, ext_wde_min_qt_wcpu);
+
+	dle_func_en(rtwdev, true);
+
+	ret = read_poll_timeout(rtw89_read32, ini,
+				(ini & WDE_MGN_INI_RDY) == WDE_MGN_INI_RDY, 1,
+				2000, false, rtwdev, R_AX_WDE_INI_STATUS);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]WDE cfg ready\n");
+		return ret;
+	}
+
+	ret = read_poll_timeout(rtw89_read32, ini,
+				(ini & WDE_MGN_INI_RDY) == WDE_MGN_INI_RDY, 1,
+				2000, false, rtwdev, R_AX_PLE_INI_STATUS);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]PLE cfg ready\n");
+		return ret;
+	}
+
+	return 0;
+error:
+	dle_func_en(rtwdev, false);
+	rtw89_err(rtwdev, "[ERR]trxcfg wde 0x8900 = %x\n",
+		  rtw89_read32(rtwdev, R_AX_WDE_INI_STATUS));
+	rtw89_err(rtwdev, "[ERR]trxcfg ple 0x8D00 = %x\n",
+		  rtw89_read32(rtwdev, R_AX_PLE_INI_STATUS));
+
+	return ret;
+}
+
+static bool dle_is_txq_empty(struct rtw89_dev *rtwdev)
+{
+	u32 msk32;
+	u32 val32;
+
+	msk32 = B_AX_WDE_EMPTY_QUE_CMAC0_ALL_AC | B_AX_WDE_EMPTY_QUE_CMAC0_MBH |
+		B_AX_WDE_EMPTY_QUE_CMAC1_MBH | B_AX_WDE_EMPTY_QUE_CMAC0_WMM0 |
+		B_AX_WDE_EMPTY_QUE_CMAC0_WMM1 | B_AX_WDE_EMPTY_QUE_OTHERS |
+		B_AX_PLE_EMPTY_QUE_DMAC_MPDU_TX | B_AX_PLE_EMPTY_QTA_DMAC_H2C |
+		B_AX_PLE_EMPTY_QUE_DMAC_SEC_TX | B_AX_WDE_EMPTY_QUE_DMAC_PKTIN |
+		B_AX_WDE_EMPTY_QTA_DMAC_HIF | B_AX_WDE_EMPTY_QTA_DMAC_WLAN_CPU |
+		B_AX_WDE_EMPTY_QTA_DMAC_PKTIN | B_AX_WDE_EMPTY_QTA_DMAC_CPUIO |
+		B_AX_PLE_EMPTY_QTA_DMAC_B0_TXPL |
+		B_AX_PLE_EMPTY_QTA_DMAC_B1_TXPL |
+		B_AX_PLE_EMPTY_QTA_DMAC_MPDU_TX |
+		B_AX_PLE_EMPTY_QTA_DMAC_CPUIO |
+		B_AX_WDE_EMPTY_QTA_DMAC_DATA_CPU |
+		B_AX_PLE_EMPTY_QTA_DMAC_WLAN_CPU;
+	val32 = rtw89_read32(rtwdev, R_AX_DLE_EMPTY0);
+
+	if ((val32 & msk32) == msk32)
+		return true;
+
+	return false;
+}
+
+static int sta_sch_init(struct rtw89_dev *rtwdev)
+{
+	u32 p_val;
+	u8 val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	val = rtw89_read8(rtwdev, R_AX_SS_CTRL);
+	val |= B_AX_SS_EN;
+	rtw89_write8(rtwdev, R_AX_SS_CTRL, val);
+
+	ret = read_poll_timeout(rtw89_read32, p_val, p_val & B_AX_SS_INIT_DONE_1,
+				1, TRXCFG_WAIT_CNT, false, rtwdev, R_AX_SS_CTRL);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]STA scheduler init\n");
+		return ret;
+	}
+
+	rtw89_write32_set(rtwdev, R_AX_SS_CTRL, B_AX_SS_WARM_INIT_FLG);
+
+	return 0;
+}
+
+static int mpdu_proc_init(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	rtw89_write32(rtwdev, R_AX_ACTION_FWD0, TRXCFG_MPDU_PROC_ACT_FRWD);
+	rtw89_write32(rtwdev, R_AX_TF_FWD, TRXCFG_MPDU_PROC_TF_FRWD);
+	rtw89_write32_set(rtwdev, R_AX_MPDU_PROC,
+			  B_AX_APPEND_FCS | B_AX_A_ICV_ERR);
+	rtw89_write32(rtwdev, R_AX_CUT_AMSDU_CTRL, TRXCFG_MPDU_PROC_CUT_CTRL);
+
+	return 0;
+}
+
+static int sec_eng_init(struct rtw89_dev *rtwdev)
+{
+	u32 val = 0;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret)
+		return ret;
+
+	val = rtw89_read32(rtwdev, R_AX_SEC_ENG_CTRL);
+	/* init clock */
+	val |= (B_AX_CLK_EN_CGCMP | B_AX_CLK_EN_WAPI | B_AX_CLK_EN_WEP_TKIP);
+	/* init TX encryption */
+	val |= (B_AX_SEC_TX_ENC | B_AX_SEC_RX_DEC);
+	val |= (B_AX_MC_DEC | B_AX_BC_DEC);
+	val &= ~B_AX_TX_PARTIAL_MODE;
+	rtw89_write32(rtwdev, R_AX_SEC_ENG_CTRL, val);
+
+	/* init MIC ICV append */
+	val = rtw89_read32(rtwdev, R_AX_SEC_MPDU_PROC);
+	val |= (B_AX_APPEND_ICV | B_AX_APPEND_MIC);
+
+	/* option init */
+	rtw89_write32(rtwdev, R_AX_SEC_MPDU_PROC, val);
+
+	return 0;
+}
+
+static int dmac_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	int ret;
+
+	ret = dle_init(rtwdev, rtwdev->mac.qta_mode, RTW89_QTA_INVALID);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]DLE init %d\n", ret);
+		return ret;
+	}
+
+	ret = hfc_init(rtwdev, true, true, true);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]HCI FC init %d\n", ret);
+		return ret;
+	}
+
+	ret = sta_sch_init(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]STA SCH init %d\n", ret);
+		return ret;
+	}
+
+	ret = mpdu_proc_init(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]MPDU Proc init %d\n", ret);
+		return ret;
+	}
+
+	ret = sec_eng_init(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]Security Engine init %d\n", ret);
+		return ret;
+	}
+
+	return ret;
+}
+
+static int addr_cam_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 val, reg;
+	u16 p_val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_ADDR_CAM_CTRL, mac_idx);
+
+	val = rtw89_read32(rtwdev, reg);
+	val |= u32_encode_bits(0x7f, B_AX_ADDR_CAM_RANGE_MASK) |
+	       B_AX_ADDR_CAM_CLR | B_AX_ADDR_CAM_EN;
+	rtw89_write32(rtwdev, reg, val);
+
+	ret = read_poll_timeout(rtw89_read16, p_val, !(p_val & B_AX_ADDR_CAM_CLR),
+				1, TRXCFG_WAIT_CNT, false, rtwdev, B_AX_ADDR_CAM_CLR);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]ADDR_CAM reset\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int scheduler_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 ret;
+	u32 reg;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_PREBKF_CFG_0, mac_idx);
+	rtw89_write32_mask(rtwdev, reg, B_AX_PREBKF_TIME_MASK, SCH_PREBKF_24US);
+
+	return 0;
+}
+
+static int rtw89_mac_typ_fltr_opt(struct rtw89_dev *rtwdev,
+				  enum rtw89_machdr_frame_type type,
+				  enum rtw89_mac_fwd_target fwd_target,
+				  u8 mac_idx)
+{
+	u32 reg;
+	u32 val;
+
+	switch (fwd_target) {
+	case RTW89_FWD_DONT_CARE:
+		val = RX_FLTR_FRAME_DROP;
+		break;
+	case RTW89_FWD_TO_HOST:
+		val = RX_FLTR_FRAME_TO_HOST;
+		break;
+	case RTW89_FWD_TO_WLAN_CPU:
+		val = RX_FLTR_FRAME_TO_WLCPU;
+		break;
+	default:
+		rtw89_err(rtwdev, "[ERR]set rx filter fwd target err\n");
+		return -EINVAL;
+	}
+
+	switch (type) {
+	case RTW89_MGNT:
+		reg = rtw89_mac_reg_by_idx(R_AX_MGNT_FLTR, mac_idx);
+		break;
+	case RTW89_CTRL:
+		reg = rtw89_mac_reg_by_idx(R_AX_CTRL_FLTR, mac_idx);
+		break;
+	case RTW89_DATA:
+		reg = rtw89_mac_reg_by_idx(R_AX_DATA_FLTR, mac_idx);
+		break;
+	default:
+		rtw89_err(rtwdev, "[ERR]set rx filter type err\n");
+		return -EINVAL;
+	}
+	rtw89_write32(rtwdev, reg, val);
+
+	return 0;
+}
+
+static int rx_fltr_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	int ret, i;
+	u32 mac_ftlr, plcp_ftlr;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	for (i = RTW89_MGNT; i <= RTW89_DATA; i++) {
+		ret = rtw89_mac_typ_fltr_opt(rtwdev, i, RTW89_FWD_TO_HOST,
+					     mac_idx);
+		if (ret)
+			return ret;
+	}
+	mac_ftlr = rtwdev->hal.rx_fltr;
+	plcp_ftlr = B_AX_CCK_CRC_CHK | B_AX_CCK_SIG_CHK |
+		    B_AX_LSIG_PARITY_CHK_EN | B_AX_SIGA_CRC_CHK |
+		    B_AX_VHT_SU_SIGB_CRC_CHK | B_AX_VHT_MU_SIGB_CRC_CHK |
+		    B_AX_HE_SIGB_CRC_CHK;
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_RX_FLTR_OPT, mac_idx),
+		      mac_ftlr);
+	rtw89_write16(rtwdev, rtw89_mac_reg_by_idx(R_AX_PLCP_HDR_FLTR, mac_idx),
+		      plcp_ftlr);
+
+	return 0;
+}
+
+static void _patch_dis_resp_chk(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 reg, val32;
+	u32 b_rsp_chk_nav, b_rsp_chk_cca;
+
+	b_rsp_chk_nav = B_AX_RSP_CHK_TXNAV | B_AX_RSP_CHK_INTRA_NAV |
+			B_AX_RSP_CHK_BASIC_NAV;
+	b_rsp_chk_cca = B_AX_RSP_CHK_SEC_CCA_80 | B_AX_RSP_CHK_SEC_CCA_40 |
+			B_AX_RSP_CHK_SEC_CCA_20 | B_AX_RSP_CHK_BTCCA |
+			B_AX_RSP_CHK_EDCCA | B_AX_RSP_CHK_CCA;
+
+	switch (rtwdev->chip->chip_id) {
+	case RTL8852A:
+	case RTL8852B:
+		reg = rtw89_mac_reg_by_idx(R_AX_RSP_CHK_SIG, mac_idx);
+		val32 = rtw89_read32(rtwdev, reg) & ~b_rsp_chk_nav;
+		rtw89_write32(rtwdev, reg, val32);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_0, mac_idx);
+		val32 = rtw89_read32(rtwdev, reg) & ~b_rsp_chk_cca;
+		rtw89_write32(rtwdev, reg, val32);
+		break;
+	default:
+		reg = rtw89_mac_reg_by_idx(R_AX_RSP_CHK_SIG, mac_idx);
+		val32 = rtw89_read32(rtwdev, reg) | b_rsp_chk_nav;
+		rtw89_write32(rtwdev, reg, val32);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_0, mac_idx);
+		val32 = rtw89_read32(rtwdev, reg) | b_rsp_chk_cca;
+		rtw89_write32(rtwdev, reg, val32);
+		break;
+	}
+}
+
+static int cca_ctrl_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_CCA_CONTROL, mac_idx);
+	val = rtw89_read32(rtwdev, reg);
+	val |= (B_AX_TB_CHK_BASIC_NAV | B_AX_TB_CHK_BTCCA |
+		B_AX_TB_CHK_EDCCA | B_AX_TB_CHK_CCA_P20 |
+		B_AX_SIFS_CHK_BTCCA | B_AX_SIFS_CHK_CCA_P20 |
+		B_AX_CTN_CHK_INTRA_NAV |
+		B_AX_CTN_CHK_BASIC_NAV | B_AX_CTN_CHK_BTCCA |
+		B_AX_CTN_CHK_EDCCA | B_AX_CTN_CHK_CCA_S80 |
+		B_AX_CTN_CHK_CCA_S40 | B_AX_CTN_CHK_CCA_S20 |
+		B_AX_CTN_CHK_CCA_P20 | B_AX_SIFS_CHK_EDCCA);
+	val &= ~(B_AX_TB_CHK_TX_NAV | B_AX_TB_CHK_CCA_S80 |
+		 B_AX_TB_CHK_CCA_S40 | B_AX_TB_CHK_CCA_S20 |
+		 B_AX_SIFS_CHK_CCA_S80 | B_AX_SIFS_CHK_CCA_S40 |
+		 B_AX_SIFS_CHK_CCA_S20 | B_AX_CTN_CHK_TXNAV);
+
+	rtw89_write32(rtwdev, reg, val);
+
+	_patch_dis_resp_chk(rtwdev, mac_idx);
+
+	return 0;
+}
+
+static int spatial_reuse_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 reg;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+	reg = rtw89_mac_reg_by_idx(R_AX_RX_SR_CTRL, mac_idx);
+	rtw89_write8_clr(rtwdev, reg, B_AX_SR_EN);
+
+	return 0;
+}
+
+static int tmac_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 reg;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_MAC_LOOPBACK, mac_idx);
+	rtw89_write32_clr(rtwdev, reg, B_AX_MACLBK_EN);
+
+	return 0;
+}
+
+static int trxptcl_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 reg, val, sifs;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_0, mac_idx);
+	val = rtw89_read32(rtwdev, reg);
+	val &= ~B_AX_WMAC_SPEC_SIFS_CCK_MASK;
+	val |= FIELD_PREP(B_AX_WMAC_SPEC_SIFS_CCK_MASK, WMAC_SPEC_SIFS_CCK);
+
+	switch (rtwdev->chip->chip_id) {
+	case RTL8852A:
+		sifs = WMAC_SPEC_SIFS_OFDM_52A;
+		break;
+	case RTL8852B:
+		sifs = WMAC_SPEC_SIFS_OFDM_52B;
+		break;
+	default:
+		sifs = WMAC_SPEC_SIFS_OFDM_52C;
+		break;
+	}
+	val &= ~B_AX_WMAC_SPEC_SIFS_OFDM_MASK;
+	val |= FIELD_PREP(B_AX_WMAC_SPEC_SIFS_OFDM_MASK, sifs);
+	rtw89_write32(rtwdev, reg, val);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_RXTRIG_TEST_USER_2, mac_idx);
+	rtw89_write32_set(rtwdev, reg, B_AX_RXTRIG_FCSCHK_EN);
+
+	return 0;
+}
+
+static int rmac_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+#define TRXCFG_RMAC_CCA_TO	32
+#define TRXCFG_RMAC_DATA_TO	15
+#define RX_MAX_LEN_UNIT 512
+#define PLD_RLS_MAX_PG 127
+	int ret;
+	u32 reg, rx_max_len, rx_qta;
+	u16 val;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_RESPBA_CAM_CTRL, mac_idx);
+	rtw89_write8_set(rtwdev, reg, B_AX_SSN_SEL);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_DLK_PROTECT_CTL, mac_idx);
+	val = rtw89_read16(rtwdev, reg);
+	val = u16_replace_bits(val, TRXCFG_RMAC_DATA_TO,
+			       B_AX_RX_DLK_DATA_TIME_MASK);
+	val = u16_replace_bits(val, TRXCFG_RMAC_CCA_TO,
+			       B_AX_RX_DLK_CCA_TIME_MASK);
+	rtw89_write16(rtwdev, reg, val);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_RCR, mac_idx);
+	rtw89_write8_mask(rtwdev, reg, B_AX_CH_EN_MASK, 0x1);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_RX_FLTR_OPT, mac_idx);
+	if (mac_idx == RTW89_MAC_0)
+		rx_qta = rtwdev->mac.dle_info.c0_rx_qta;
+	else
+		rx_qta = rtwdev->mac.dle_info.c1_rx_qta;
+	rx_qta = rx_qta > PLD_RLS_MAX_PG ? PLD_RLS_MAX_PG : rx_qta;
+	rx_max_len = (rx_qta - 1) * rtwdev->mac.dle_info.ple_pg_size /
+		     RX_MAX_LEN_UNIT;
+	rx_max_len = rx_max_len > B_AX_RX_MPDU_MAX_LEN_SIZE ?
+		     B_AX_RX_MPDU_MAX_LEN_SIZE : rx_max_len;
+	rtw89_write32_mask(rtwdev, reg, B_AX_RX_MPDU_MAX_LEN_MASK, rx_max_len);
+
+	if (rtwdev->chip->chip_id == RTL8852A &&
+	    rtwdev->hal.cv == CHIP_CBV) {
+		rtw89_write16_mask(rtwdev,
+				   rtw89_mac_reg_by_idx(R_AX_DLK_PROTECT_CTL, mac_idx),
+				   B_AX_RX_DLK_CCA_TIME_MASK, 0);
+		rtw89_write16_set(rtwdev, rtw89_mac_reg_by_idx(R_AX_RCR, mac_idx),
+				  BIT(12));
+	}
+
+	reg = rtw89_mac_reg_by_idx(R_AX_PLCP_HDR_FLTR, mac_idx);
+	rtw89_write8_clr(rtwdev, reg, B_AX_VHT_SU_SIGB_CRC_CHK);
+
+	return ret;
+}
+
+static int cmac_com_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_TX_SUB_CARRIER_VALUE, mac_idx);
+	val = rtw89_read32(rtwdev, reg);
+	val = u32_replace_bits(val, 0, B_AX_TXSC_20M_MASK);
+	val = u32_replace_bits(val, 0, B_AX_TXSC_40M_MASK);
+	val = u32_replace_bits(val, 0, B_AX_TXSC_80M_MASK);
+	rtw89_write32(rtwdev, reg, val);
+
+	return 0;
+}
+
+static bool is_qta_dbcc(struct rtw89_dev *rtwdev, enum rtw89_qta_mode mode)
+{
+	const struct rtw89_dle_mem *cfg;
+
+	cfg = get_dle_mem_cfg(rtwdev, mode);
+	if (!cfg) {
+		rtw89_err(rtwdev, "[ERR]get_dle_mem_cfg\n");
+		return false;
+	}
+
+	return (cfg->ple_min_qt->cma1_dma && cfg->ple_max_qt->cma1_dma);
+}
+
+static int ptcl_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	if (rtwdev->hci.type == RTW89_HCI_TYPE_PCIE) {
+		reg = rtw89_mac_reg_by_idx(R_AX_SIFS_SETTING, mac_idx);
+		val = rtw89_read32(rtwdev, reg);
+		val = u32_replace_bits(val, S_AX_CTS2S_TH_1K,
+				       B_AX_HW_CTS2SELF_PKT_LEN_TH_MASK);
+		val |= B_AX_HW_CTS2SELF_EN;
+		rtw89_write32(rtwdev, reg, val);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_PTCL_FSM_MON, mac_idx);
+		val = rtw89_read32(rtwdev, reg);
+		val = u32_replace_bits(val, S_AX_PTCL_TO_2MS, B_AX_PTCL_TX_ARB_TO_THR_MASK);
+		val &= ~B_AX_PTCL_TX_ARB_TO_MODE;
+		rtw89_write32(rtwdev, reg, val);
+	}
+
+	reg = rtw89_mac_reg_by_idx(R_AX_SIFS_SETTING, mac_idx);
+	val = rtw89_read32(rtwdev, reg);
+	val = u32_replace_bits(val, S_AX_CTS2S_TH_SEC_256B, B_AX_HW_CTS2SELF_PKT_LEN_TH_TWW_MASK);
+	val |= B_AX_HW_CTS2SELF_EN;
+	rtw89_write32(rtwdev, reg, val);
+
+	return 0;
+}
+
+static int cmac_init(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	int ret;
+
+	ret = scheduler_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d SCH init %d\n", mac_idx, ret);
+		return ret;
+	}
+
+	ret = addr_cam_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d ADDR_CAM reset %d\n", mac_idx,
+			  ret);
+		return ret;
+	}
+
+	ret = rx_fltr_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d RX filter init %d\n", mac_idx,
+			  ret);
+		return ret;
+	}
+
+	ret = cca_ctrl_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d CCA CTRL init %d\n", mac_idx,
+			  ret);
+		return ret;
+	}
+
+	ret = spatial_reuse_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d Spatial Reuse init %d\n",
+			  mac_idx, ret);
+		return ret;
+	}
+
+	ret = tmac_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d TMAC init %d\n", mac_idx, ret);
+		return ret;
+	}
+
+	ret = trxptcl_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d TRXPTCL init %d\n", mac_idx, ret);
+		return ret;
+	}
+
+	ret = rmac_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d RMAC init %d\n", mac_idx, ret);
+		return ret;
+	}
+
+	ret = cmac_com_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d Com init %d\n", mac_idx, ret);
+		return ret;
+	}
+
+	ret = ptcl_init(rtwdev, mac_idx);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d PTCL init %d\n", mac_idx, ret);
+		return ret;
+	}
+
+	return ret;
+}
+
+static int rtw89_mac_read_phycap(struct rtw89_dev *rtwdev,
+				 struct rtw89_mac_c2h_info *c2h_info)
+{
+	struct rtw89_mac_h2c_info h2c_info = {0};
+	u32 ret;
+
+	h2c_info.id = RTW89_FWCMD_H2CREG_FUNC_GET_FEATURE;
+	h2c_info.content_len = 0;
+
+	ret = rtw89_fw_msg_reg(rtwdev, &h2c_info, c2h_info);
+	if (ret)
+		return ret;
+
+	if (c2h_info->id != RTW89_FWCMD_C2HREG_FUNC_PHY_CAP)
+		return -EINVAL;
+
+	return 0;
+}
+
+int rtw89_mac_setup_phycap(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_hal *hal = &rtwdev->hal;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_mac_c2h_info c2h_info = {0};
+	struct rtw89_c2h_phy_cap *cap =
+		(struct rtw89_c2h_phy_cap *)&c2h_info.c2hreg[0];
+	u32 ret;
+
+	ret = rtw89_mac_read_phycap(rtwdev, &c2h_info);
+	if (ret)
+		return ret;
+
+	hal->tx_nss = cap->tx_nss ?
+		      min_t(u8, cap->tx_nss, chip->tx_nss) : chip->tx_nss;
+	hal->rx_nss = cap->rx_nss ?
+		      min_t(u8, cap->rx_nss, chip->rx_nss) : chip->rx_nss;
+
+	rtw89_debug(rtwdev, RTW89_DBG_FW,
+		    "phycap hal/phy/chip: tx_nss=0x%x/0x%x/0x%x rx_nss=0x%x/0x%x/0x%x\n",
+		    hal->tx_nss, cap->tx_nss, chip->tx_nss,
+		    hal->rx_nss, cap->rx_nss, chip->rx_nss);
+
+	return 0;
+}
+
+static int rtw89_hw_sch_tx_en_h2c(struct rtw89_dev *rtwdev, u8 band,
+				  u16 tx_en_u16, u16 mask_u16)
+{
+	u32 ret;
+	struct rtw89_mac_c2h_info c2h_info = {0};
+	struct rtw89_mac_h2c_info h2c_info = {0};
+	struct rtw89_h2creg_sch_tx_en *h2creg =
+		(struct rtw89_h2creg_sch_tx_en *)h2c_info.h2creg;
+
+	h2c_info.id = RTW89_FWCMD_H2CREG_FUNC_SCH_TX_EN;
+	h2c_info.content_len = sizeof(*h2creg) - RTW89_H2CREG_HDR_LEN;
+	h2creg->tx_en = tx_en_u16;
+	h2creg->mask = mask_u16;
+	h2creg->band = band;
+
+	ret = rtw89_fw_msg_reg(rtwdev, &h2c_info, &c2h_info);
+	if (ret)
+		return ret;
+
+	if (c2h_info.id != RTW89_FWCMD_C2HREG_FUNC_TX_PAUSE_RPT)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int rtw89_set_hw_sch_tx_en(struct rtw89_dev *rtwdev, u8 mac_idx,
+				  u16 tx_en, u16 tx_en_mask)
+{
+	u32 reg = rtw89_mac_reg_by_idx(R_AX_CTN_TXEN, mac_idx);
+	u16 val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	if (test_bit(RTW89_FLAG_FW_RDY, rtwdev->flags))
+		return rtw89_hw_sch_tx_en_h2c(rtwdev, mac_idx,
+					      tx_en, tx_en_mask);
+
+	val = rtw89_read16(rtwdev, reg);
+	val = (val & ~tx_en_mask) | (tx_en & tx_en_mask);
+	rtw89_write16(rtwdev, reg, val);
+
+	return 0;
+}
+
+int rtw89_mac_stop_sch_tx(struct rtw89_dev *rtwdev, u8 mac_idx,
+			  u16 *tx_en, enum rtw89_sch_tx_sel sel)
+{
+	int ret;
+
+	*tx_en = rtw89_read16(rtwdev,
+			      rtw89_mac_reg_by_idx(R_AX_CTN_TXEN, mac_idx));
+
+	switch (sel) {
+	case RTW89_SCH_TX_SEL_ALL:
+		ret = rtw89_set_hw_sch_tx_en(rtwdev, mac_idx, 0, 0xffff);
+		if (ret)
+			return ret;
+		break;
+	case RTW89_SCH_TX_SEL_HIQ:
+		ret = rtw89_set_hw_sch_tx_en(rtwdev, mac_idx,
+					     0, B_AX_CTN_TXEN_HGQ);
+		if (ret)
+			return ret;
+		break;
+	case RTW89_SCH_TX_SEL_MG0:
+		ret = rtw89_set_hw_sch_tx_en(rtwdev, mac_idx,
+					     0, B_AX_CTN_TXEN_MGQ);
+		if (ret)
+			return ret;
+		break;
+	case RTW89_SCH_TX_SEL_MACID:
+		ret = rtw89_set_hw_sch_tx_en(rtwdev, mac_idx, 0, 0xffff);
+		if (ret)
+			return ret;
+		break;
+	default:
+		return 0;
+	}
+
+	return 0;
+}
+
+int rtw89_mac_resume_sch_tx(struct rtw89_dev *rtwdev, u8 mac_idx, u16 tx_en)
+{
+	int ret;
+
+	ret = rtw89_set_hw_sch_tx_en(rtwdev, mac_idx, tx_en, 0xffff);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static u16 rtw89_mac_dle_buf_req(struct rtw89_dev *rtwdev, u16 buf_len,
+				 bool wd)
+{
+	u32 val, reg;
+	int ret;
+
+	reg = wd ? R_AX_WD_BUF_REQ : R_AX_PL_BUF_REQ;
+	val = buf_len;
+	val |= B_AX_WD_BUF_REQ_EXEC;
+	rtw89_write32(rtwdev, reg, val);
+
+	reg = wd ? R_AX_WD_BUF_STATUS : R_AX_PL_BUF_STATUS;
+
+	ret = read_poll_timeout(rtw89_read32, val, val & B_AX_WD_BUF_STAT_DONE,
+				1, 2000, false, rtwdev, reg);
+	if (ret)
+		return 0xffff;
+
+	return FIELD_GET(B_AX_WD_BUF_STAT_PKTID_MASK, val);
+}
+
+static int rtw89_mac_set_cpuio(struct rtw89_dev *rtwdev,
+			       struct rtw89_cpuio_ctrl *ctrl_para,
+			       bool wd)
+{
+	u32 val, cmd_type, reg;
+	int ret;
+
+	cmd_type = ctrl_para->cmd_type;
+
+	reg = wd ? R_AX_WD_CPUQ_OP_2 : R_AX_PL_CPUQ_OP_2;
+	val = 0;
+	val = u32_replace_bits(val, ctrl_para->start_pktid,
+			       B_AX_WD_CPUQ_OP_STRT_PKTID_MASK);
+	val = u32_replace_bits(val, ctrl_para->end_pktid,
+			       B_AX_WD_CPUQ_OP_END_PKTID_MASK);
+	rtw89_write32(rtwdev, reg, val);
+
+	reg = wd ? R_AX_WD_CPUQ_OP_1 : R_AX_PL_CPUQ_OP_1;
+	val = 0;
+	val = u32_replace_bits(val, ctrl_para->src_pid,
+			       B_AX_CPUQ_OP_SRC_PID_MASK);
+	val = u32_replace_bits(val, ctrl_para->src_qid,
+			       B_AX_CPUQ_OP_SRC_QID_MASK);
+	val = u32_replace_bits(val, ctrl_para->dst_pid,
+			       B_AX_CPUQ_OP_DST_PID_MASK);
+	val = u32_replace_bits(val, ctrl_para->dst_qid,
+			       B_AX_CPUQ_OP_DST_QID_MASK);
+	rtw89_write32(rtwdev, reg, val);
+
+	reg = wd ? R_AX_WD_CPUQ_OP_0 : R_AX_PL_CPUQ_OP_0;
+	val = 0;
+	val = u32_replace_bits(val, cmd_type,
+			       B_AX_CPUQ_OP_CMD_TYPE_MASK);
+	val = u32_replace_bits(val, ctrl_para->macid,
+			       B_AX_CPUQ_OP_MACID_MASK);
+	val = u32_replace_bits(val, ctrl_para->pkt_num,
+			       B_AX_CPUQ_OP_PKTNUM_MASK);
+	val |= B_AX_WD_CPUQ_OP_EXEC;
+	rtw89_write32(rtwdev, reg, val);
+
+	reg = wd ? R_AX_WD_CPUQ_OP_STATUS : R_AX_PL_CPUQ_OP_STATUS;
+
+	ret = read_poll_timeout(rtw89_read32, val, val & B_AX_WD_CPUQ_OP_STAT_DONE,
+				1, 2000, false, rtwdev, reg);
+	if (ret)
+		return ret;
+
+	if (cmd_type == CPUIO_OP_CMD_GET_1ST_PID ||
+	    cmd_type == CPUIO_OP_CMD_GET_NEXT_PID)
+		ctrl_para->pktid = FIELD_GET(B_AX_WD_CPUQ_OP_PKTID_MASK, val);
+
+	return 0;
+}
+
+static int dle_quota_change(struct rtw89_dev *rtwdev, enum rtw89_qta_mode mode)
+{
+	const struct rtw89_dle_mem *cfg;
+	struct rtw89_cpuio_ctrl ctrl_para = {0};
+	u16 pkt_id;
+	int ret;
+
+	cfg = get_dle_mem_cfg(rtwdev, mode);
+	if (!cfg) {
+		rtw89_err(rtwdev, "[ERR]wd/dle mem cfg\n");
+		return -EINVAL;
+	}
+
+	if (dle_used_size(cfg->wde_size, cfg->ple_size) != rtwdev->chip->fifo_size) {
+		rtw89_err(rtwdev, "[ERR]wd/dle mem cfg\n");
+		return -EINVAL;
+	}
+
+	dle_quota_cfg(rtwdev, cfg, INVALID_QT_WCPU);
+
+	pkt_id = rtw89_mac_dle_buf_req(rtwdev, 0x20, true);
+	if (pkt_id == 0xffff) {
+		rtw89_err(rtwdev, "[ERR]WDE DLE buf req\n");
+		return -ENOMEM;
+	}
+
+	ctrl_para.cmd_type = CPUIO_OP_CMD_ENQ_TO_HEAD;
+	ctrl_para.start_pktid = pkt_id;
+	ctrl_para.end_pktid = pkt_id;
+	ctrl_para.pkt_num = 0;
+	ctrl_para.dst_pid = WDE_DLE_PORT_ID_WDRLS;
+	ctrl_para.dst_qid = WDE_DLE_QUEID_NO_REPORT;
+	ret = rtw89_mac_set_cpuio(rtwdev, &ctrl_para, true);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]WDE DLE enqueue to head\n");
+		return -EFAULT;
+	}
+
+	pkt_id = rtw89_mac_dle_buf_req(rtwdev, 0x20, false);
+	if (pkt_id == 0xffff) {
+		rtw89_err(rtwdev, "[ERR]PLE DLE buf req\n");
+		return -ENOMEM;
+	}
+
+	ctrl_para.cmd_type = CPUIO_OP_CMD_ENQ_TO_HEAD;
+	ctrl_para.start_pktid = pkt_id;
+	ctrl_para.end_pktid = pkt_id;
+	ctrl_para.pkt_num = 0;
+	ctrl_para.dst_pid = PLE_DLE_PORT_ID_PLRLS;
+	ctrl_para.dst_qid = PLE_DLE_QUEID_NO_REPORT;
+	ret = rtw89_mac_set_cpuio(rtwdev, &ctrl_para, false);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]PLE DLE enqueue to head\n");
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+static int band_idle_ck_b(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	int ret;
+	u32 reg;
+	u8 val;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_PTCL_TX_CTN_SEL, mac_idx);
+
+	ret = read_poll_timeout(rtw89_read8, val,
+				(val & B_AX_PTCL_TX_ON_STAT) == 0,
+				SW_CVR_DUR_US,
+				SW_CVR_DUR_US * PTCL_IDLE_POLL_CNT,
+				false, rtwdev, reg);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int band1_enable(struct rtw89_dev *rtwdev)
+{
+	int ret, i;
+	u32 sleep_bak[4] = {0};
+	u32 pause_bak[4] = {0};
+	u16 tx_en;
+
+	ret = rtw89_mac_stop_sch_tx(rtwdev, 0, &tx_en, RTW89_SCH_TX_SEL_ALL);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]stop sch tx %d\n", ret);
+		return ret;
+	}
+
+	for (i = 0; i < 4; i++) {
+		sleep_bak[i] = rtw89_read32(rtwdev, R_AX_MACID_SLEEP_0 + i * 4);
+		pause_bak[i] = rtw89_read32(rtwdev, R_AX_SS_MACID_PAUSE_0 + i * 4);
+		rtw89_write32(rtwdev, R_AX_MACID_SLEEP_0 + i * 4, U32_MAX);
+		rtw89_write32(rtwdev, R_AX_SS_MACID_PAUSE_0 + i * 4, U32_MAX);
+	}
+
+	ret = band_idle_ck_b(rtwdev, 0);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]tx idle poll %d\n", ret);
+		return ret;
+	}
+
+	ret = dle_quota_change(rtwdev, rtwdev->mac.qta_mode);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]DLE quota change %d\n", ret);
+		return ret;
+	}
+
+	for (i = 0; i < 4; i++) {
+		rtw89_write32(rtwdev, R_AX_MACID_SLEEP_0 + i * 4, sleep_bak[i]);
+		rtw89_write32(rtwdev, R_AX_SS_MACID_PAUSE_0 + i * 4, pause_bak[i]);
+	}
+
+	ret = rtw89_mac_resume_sch_tx(rtwdev, 0, tx_en);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC1 resume sch tx %d\n", ret);
+		return ret;
+	}
+
+	ret = cmac_func_en(rtwdev, 1, true);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC1 func en %d\n", ret);
+		return ret;
+	}
+
+	ret = cmac_init(rtwdev, 1);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC1 init %d\n", ret);
+		return ret;
+	}
+
+	rtw89_write32_set(rtwdev, R_AX_SYS_ISO_CTRL_EXTEND,
+			  B_AX_R_SYM_FEN_WLBBFUN_1 | B_AX_R_SYM_FEN_WLBBGLB_1);
+
+	return 0;
+}
+
+static int rtw89_mac_enable_imr(struct rtw89_dev *rtwdev, u8 mac_idx,
+				enum rtw89_mac_hwmod_sel sel)
+{
+	u32 reg, val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, sel);
+	if (ret) {
+		rtw89_err(rtwdev, "MAC%d mac_idx%d is not ready\n",
+			  sel, mac_idx);
+		return ret;
+	}
+
+	if (sel == RTW89_DMAC_SEL) {
+		rtw89_write32_clr(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR,
+				  B_AX_TXPKTCTL_USRCTL_RLSBMPLEN_ERR_INT_EN |
+				  B_AX_TXPKTCTL_USRCTL_RDNRLSCMD_ERR_INT_EN |
+				  B_AX_TXPKTCTL_CMDPSR_FRZTO_ERR_INT_EN);
+		rtw89_write32_clr(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR_B1,
+				  B_AX_TXPKTCTL_USRCTL_RLSBMPLEN_ERR_INT_EN |
+				  B_AX_TXPKTCTL_USRCTL_RDNRLSCMD_ERR_INT_EN);
+		rtw89_write32_clr(rtwdev, R_AX_HOST_DISPATCHER_ERR_IMR,
+				  B_AX_HDT_PKT_FAIL_DBG_INT_EN |
+				  B_AX_HDT_OFFSET_UNMATCH_INT_EN);
+		rtw89_write32_clr(rtwdev, R_AX_CPU_DISPATCHER_ERR_IMR,
+				  B_AX_CPU_SHIFT_EN_ERR_INT_EN);
+		rtw89_write32_clr(rtwdev, R_AX_PLE_ERR_IMR,
+				  B_AX_PLE_GETNPG_STRPG_ERR_INT_EN);
+		rtw89_write32_clr(rtwdev, R_AX_WDRLS_ERR_IMR,
+				  B_AX_WDRLS_PLEBREQ_TO_ERR_INT_EN);
+		rtw89_write32_set(rtwdev, R_AX_HD0IMR, B_AX_WDT_PTFM_INT_EN);
+		rtw89_write32_clr(rtwdev, R_AX_TXPKTCTL_ERR_IMR_ISR,
+				  B_AX_TXPKTCTL_USRCTL_NOINIT_ERR_INT_EN);
+	} else if (sel == RTW89_CMAC_SEL) {
+		reg = rtw89_mac_reg_by_idx(R_AX_SCHEDULE_ERR_IMR, mac_idx);
+		rtw89_write32_clr(rtwdev, reg,
+				  B_AX_SORT_NON_IDLE_ERR_INT_EN);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_DLE_CTRL, mac_idx);
+		rtw89_write32_clr(rtwdev, reg,
+				  B_AX_NO_RESERVE_PAGE_ERR_IMR |
+				  B_AX_RXDATA_FSM_HANG_ERROR_IMR);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_PTCL_IMR0, mac_idx);
+		val = B_AX_F2PCMD_USER_ALLC_ERR_INT_EN |
+		      B_AX_TX_RECORD_PKTID_ERR_INT_EN |
+		      B_AX_FSM_TIMEOUT_ERR_INT_EN;
+		rtw89_write32(rtwdev, reg, val);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_PHYINFO_ERR_IMR, mac_idx);
+		rtw89_write32_set(rtwdev, reg,
+				  B_AX_PHY_TXON_TIMEOUT_INT_EN |
+				  B_AX_CCK_CCA_TIMEOUT_INT_EN |
+				  B_AX_OFDM_CCA_TIMEOUT_INT_EN |
+				  B_AX_DATA_ON_TIMEOUT_INT_EN |
+				  B_AX_STS_ON_TIMEOUT_INT_EN |
+				  B_AX_CSI_ON_TIMEOUT_INT_EN);
+
+		reg = rtw89_mac_reg_by_idx(R_AX_RMAC_ERR_ISR, mac_idx);
+		val = rtw89_read32(rtwdev, reg);
+		val |= (B_AX_RMAC_RX_CSI_TIMEOUT_INT_EN |
+			B_AX_RMAC_RX_TIMEOUT_INT_EN |
+			B_AX_RMAC_CSI_TIMEOUT_INT_EN);
+		val &= ~(B_AX_RMAC_CCA_TO_IDLE_TIMEOUT_INT_EN |
+			 B_AX_RMAC_DATA_ON_TO_IDLE_TIMEOUT_INT_EN |
+			 B_AX_RMAC_CCA_TIMEOUT_INT_EN |
+			 B_AX_RMAC_DATA_ON_TIMEOUT_INT_EN);
+		rtw89_write32(rtwdev, reg, val);
+	} else {
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int rtw89_mac_dbcc_enable(struct rtw89_dev *rtwdev, bool enable)
+{
+	int ret = 0;
+
+	if (enable) {
+		ret = band1_enable(rtwdev);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR] band1_enable %d\n", ret);
+			return ret;
+		}
+
+		ret = rtw89_mac_enable_imr(rtwdev, RTW89_MAC_1, RTW89_CMAC_SEL);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR] enable CMAC1 IMR %d\n", ret);
+			return ret;
+		}
+	} else {
+		rtw89_err(rtwdev, "[ERR] disable dbcc is not implemented not\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int set_host_rpr(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->hci.type == RTW89_HCI_TYPE_PCIE) {
+		rtw89_write32_mask(rtwdev, R_AX_WDRLS_CFG,
+				   B_AX_WDRLS_MODE_MASK, RTW89_RPR_MODE_POH);
+		rtw89_write32_set(rtwdev, R_AX_RLSRPT0_CFG0,
+				  B_AX_RLSRPT0_FLTR_MAP_MASK);
+	} else {
+		rtw89_write32_mask(rtwdev, R_AX_WDRLS_CFG,
+				   B_AX_WDRLS_MODE_MASK, RTW89_RPR_MODE_STF);
+		rtw89_write32_clr(rtwdev, R_AX_RLSRPT0_CFG0,
+				  B_AX_RLSRPT0_FLTR_MAP_MASK);
+	}
+
+	rtw89_write32_mask(rtwdev, R_AX_RLSRPT0_CFG1, B_AX_RLSRPT0_AGGNUM_MASK, 30);
+	rtw89_write32_mask(rtwdev, R_AX_RLSRPT0_CFG1, B_AX_RLSRPT0_TO_MASK, 255);
+
+	return 0;
+}
+
+static int rtw89_mac_trx_init(struct rtw89_dev *rtwdev)
+{
+	enum rtw89_qta_mode qta_mode = rtwdev->mac.qta_mode;
+	int ret;
+
+	ret = dmac_init(rtwdev, 0);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]DMAC init %d\n", ret);
+		return ret;
+	}
+
+	ret = cmac_init(rtwdev, 0);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]CMAC%d init %d\n", 0, ret);
+		return ret;
+	}
+
+	if (is_qta_dbcc(rtwdev, qta_mode)) {
+		ret = rtw89_mac_dbcc_enable(rtwdev, true);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]dbcc_enable init %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = rtw89_mac_enable_imr(rtwdev, RTW89_MAC_0, RTW89_DMAC_SEL);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] enable DMAC IMR %d\n", ret);
+		return ret;
+	}
+
+	ret = rtw89_mac_enable_imr(rtwdev, RTW89_MAC_0, RTW89_CMAC_SEL);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] to enable CMAC0 IMR %d\n", ret);
+		return ret;
+	}
+
+	ret = set_host_rpr(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] set host rpr %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void rtw89_mac_disable_cpu(struct rtw89_dev *rtwdev)
+{
+	clear_bit(RTW89_FLAG_FW_RDY, rtwdev->flags);
+
+	rtw89_write32_clr(rtwdev, R_AX_PLATFORM_ENABLE, B_AX_WCPU_EN);
+	rtw89_write32_clr(rtwdev, R_AX_SYS_CLK_CTRL, B_AX_CPU_CLK_EN);
+}
+
+static int rtw89_mac_enable_cpu(struct rtw89_dev *rtwdev, u8 boot_reason,
+				bool dlfw)
+{
+	u32 val;
+	int ret;
+
+	if (rtw89_read32(rtwdev, R_AX_PLATFORM_ENABLE) & B_AX_WCPU_EN)
+		return -EFAULT;
+
+	rtw89_write32(rtwdev, R_AX_HALT_H2C_CTRL, 0);
+	rtw89_write32(rtwdev, R_AX_HALT_C2H_CTRL, 0);
+
+	rtw89_write32_set(rtwdev, R_AX_SYS_CLK_CTRL, B_AX_CPU_CLK_EN);
+
+	val = rtw89_read32(rtwdev, R_AX_WCPU_FW_CTRL);
+	val &= ~(B_AX_WCPU_FWDL_EN | B_AX_H2C_PATH_RDY | B_AX_FWDL_PATH_RDY);
+	val = u32_replace_bits(val, RTW89_FWDL_INITIAL_STATE,
+			       B_AX_WCPU_FWDL_STS_MASK);
+
+	if (dlfw)
+		val |= B_AX_WCPU_FWDL_EN;
+
+	rtw89_write32(rtwdev, R_AX_WCPU_FW_CTRL, val);
+	rtw89_write16_mask(rtwdev, R_AX_BOOT_REASON, B_AX_BOOT_REASON_MASK,
+			   boot_reason);
+	rtw89_write32_set(rtwdev, R_AX_PLATFORM_ENABLE, B_AX_WCPU_EN);
+
+	if (!dlfw) {
+		mdelay(5);
+
+		ret = rtw89_fw_check_rdy(rtwdev);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int rtw89_mac_fw_dl_pre_init(struct rtw89_dev *rtwdev)
+{
+	u32 val;
+	int ret;
+
+	val = B_AX_MAC_FUNC_EN | B_AX_DMAC_FUNC_EN | B_AX_DISPATCHER_EN |
+	      B_AX_PKT_BUF_EN;
+	rtw89_write32(rtwdev, R_AX_DMAC_FUNC_EN, val);
+
+	val = B_AX_DISPATCHER_CLK_EN;
+	rtw89_write32(rtwdev, R_AX_DMAC_CLK_EN, val);
+
+	ret = dle_init(rtwdev, RTW89_QTA_DLFW, rtwdev->mac.qta_mode);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]DLE pre init %d\n", ret);
+		return ret;
+	}
+
+	ret = hfc_init(rtwdev, true, false, true);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]HCI FC pre init %d\n", ret);
+		return ret;
+	}
+
+	return ret;
+}
+
+static void rtw89_mac_hci_func_en(struct rtw89_dev *rtwdev)
+{
+	rtw89_write32_set(rtwdev, R_AX_HCI_FUNC_EN,
+			  B_AX_HCI_TXDMA_EN | B_AX_HCI_RXDMA_EN);
+}
+
+void rtw89_mac_enable_bb_rf(struct rtw89_dev *rtwdev)
+{
+	rtw89_write8_set(rtwdev, R_AX_SYS_FUNC_EN,
+			 B_AX_FEN_BBRSTB | B_AX_FEN_BB_GLB_RSTN);
+	rtw89_write32_set(rtwdev, R_AX_WLRF_CTRL,
+			  B_AX_WLRF1_CTRL_7 | B_AX_WLRF1_CTRL_1 |
+			  B_AX_WLRF_CTRL_7 | B_AX_WLRF_CTRL_1);
+	rtw89_write8_set(rtwdev, R_AX_PHYREG_SET, PHYREG_SET_ALL_CYCLE);
+}
+
+void rtw89_mac_disable_bb_rf(struct rtw89_dev *rtwdev)
+{
+	rtw89_write8_clr(rtwdev, R_AX_SYS_FUNC_EN,
+			 B_AX_FEN_BBRSTB | B_AX_FEN_BB_GLB_RSTN);
+	rtw89_write32_clr(rtwdev, R_AX_WLRF_CTRL,
+			  B_AX_WLRF1_CTRL_7 | B_AX_WLRF1_CTRL_1 |
+			  B_AX_WLRF_CTRL_7 | B_AX_WLRF_CTRL_1);
+	rtw89_write8_clr(rtwdev, R_AX_PHYREG_SET, PHYREG_SET_ALL_CYCLE);
+}
+
+int rtw89_mac_partial_init(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_mac_power_switch(rtwdev, true);
+	if (ret) {
+		rtw89_mac_power_switch(rtwdev, false);
+		ret = rtw89_mac_power_switch(rtwdev, true);
+		if (ret)
+			return ret;
+	}
+
+	rtw89_mac_hci_func_en(rtwdev);
+
+	if (rtwdev->hci.ops->mac_pre_init) {
+		ret = rtwdev->hci.ops->mac_pre_init(rtwdev);
+		if (ret)
+			return ret;
+	}
+
+	ret = rtw89_mac_fw_dl_pre_init(rtwdev);
+	if (ret)
+		return ret;
+
+	rtw89_mac_disable_cpu(rtwdev);
+	ret = rtw89_mac_enable_cpu(rtwdev, 0, true);
+	if (ret)
+		return ret;
+
+	ret = rtw89_fw_download(rtwdev, RTW89_FW_NORMAL);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+int rtw89_mac_init(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_mac_partial_init(rtwdev);
+	if (ret)
+		goto fail;
+
+	rtw89_mac_enable_bb_rf(rtwdev);
+
+	ret = rtw89_mac_sys_init(rtwdev);
+	if (ret)
+		goto fail;
+
+	ret = rtw89_mac_trx_init(rtwdev);
+	if (ret)
+		goto fail;
+
+	if (rtwdev->hci.ops->mac_post_init) {
+		ret = rtwdev->hci.ops->mac_post_init(rtwdev);
+		if (ret)
+			goto fail;
+	}
+
+	rtw89_fw_send_all_early_h2c(rtwdev);
+	rtw89_fw_h2c_set_ofld_cfg(rtwdev);
+
+	return ret;
+fail:
+	rtw89_mac_power_switch(rtwdev, false);
+
+	return ret;
+}
+
+static void rtw89_mac_dmac_tbl_init(struct rtw89_dev *rtwdev, u8 macid)
+{
+	u8 i;
+
+	for (i = 0; i < 4; i++) {
+		rtw89_write32(rtwdev, R_AX_FILTER_MODEL_ADDR,
+			      DMAC_TBL_BASE_ADDR + (macid << 4) + (i << 2));
+		rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY, 0);
+	}
+}
+
+static void rtw89_mac_cmac_tbl_init(struct rtw89_dev *rtwdev, u8 macid)
+{
+	rtw89_write32(rtwdev, R_AX_FILTER_MODEL_ADDR,
+		      CMAC_TBL_BASE_ADDR + macid * CCTL_INFO_SIZE);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY, 0x4);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 4, 0x400A0004);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 8, 0);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 12, 0);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 16, 0);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 20, 0xE43000B);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 24, 0);
+	rtw89_write32(rtwdev, R_AX_INDIR_ACCESS_ENTRY + 28, 0xB8109);
+}
+
+static int rtw89_set_macid_pause(struct rtw89_dev *rtwdev, u8 macid, bool pause)
+{
+	u8 sh =  FIELD_GET(GENMASK(4, 0), macid);
+	u8 grp = macid >> 5;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, RTW89_MAC_0, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	rtw89_fw_h2c_macid_pause(rtwdev, sh, grp, pause);
+
+	return 0;
+}
+
+static const struct rtw89_port_reg rtw_port_base = {
+	.port_cfg = R_AX_PORT_CFG_P0,
+	.tbtt_prohib = R_AX_TBTT_PROHIB_P0,
+	.bcn_area = R_AX_BCN_AREA_P0,
+	.bcn_early = R_AX_BCNERLYINT_CFG_P0,
+	.tbtt_early = R_AX_TBTTERLYINT_CFG_P0,
+	.tbtt_agg = R_AX_TBTT_AGG_P0,
+	.bcn_space = R_AX_BCN_SPACE_CFG_P0,
+	.bcn_forcetx = R_AX_BCN_FORCETX_P0,
+	.bcn_err_cnt = R_AX_BCN_ERR_CNT_P0,
+	.bcn_err_flag = R_AX_BCN_ERR_FLAG_P0,
+	.dtim_ctrl = R_AX_DTIM_CTRL_P0,
+	.tbtt_shift = R_AX_TBTT_SHIFT_P0,
+	.bcn_cnt_tmr = R_AX_BCN_CNT_TMR_P0,
+	.tsftr_l = R_AX_TSFTR_LOW_P0,
+	.tsftr_h = R_AX_TSFTR_HIGH_P0
+};
+
+#define BCN_INTERVAL 100
+#define BCN_ERLY_DEF 160
+#define BCN_SETUP_DEF 2
+#define BCN_HOLD_DEF 200
+#define BCN_MASK_DEF 0
+#define TBTT_ERLY_DEF 5
+#define BCN_SET_UNIT 32
+#define BCN_ERLY_SET_DLY (10 * 2)
+
+static void rtw89_mac_port_cfg_func_sw(struct rtw89_dev *rtwdev,
+				       struct rtw89_vif *rtwvif)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	if (!rtw89_read32_port_mask(rtwdev, rtwvif, p->port_cfg, B_AX_PORT_FUNC_EN))
+		return;
+
+	rtw89_write32_port_clr(rtwdev, rtwvif, p->tbtt_prohib, B_AX_TBTT_SETUP_MASK);
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->tbtt_prohib, B_AX_TBTT_HOLD_MASK, 1);
+	rtw89_write16_port_clr(rtwdev, rtwvif, p->tbtt_early, B_AX_TBTTERLY_MASK);
+	rtw89_write16_port_clr(rtwdev, rtwvif, p->bcn_early, B_AX_BCNERLY_MASK);
+
+	msleep(vif->bss_conf.beacon_int + 1);
+
+	rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, B_AX_PORT_FUNC_EN |
+							    B_AX_BRK_SETUP);
+	rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, B_AX_TSFTR_RST);
+	rtw89_write32_port(rtwdev, rtwvif, p->bcn_cnt_tmr, 0);
+}
+
+static void rtw89_mac_port_cfg_tx_rpt(struct rtw89_dev *rtwdev,
+				      struct rtw89_vif *rtwvif, bool en)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	if (en)
+		rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, B_AX_TXBCN_RPT_EN);
+	else
+		rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, B_AX_TXBCN_RPT_EN);
+}
+
+static void rtw89_mac_port_cfg_rx_rpt(struct rtw89_dev *rtwdev,
+				      struct rtw89_vif *rtwvif, bool en)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	if (en)
+		rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, B_AX_RXBCN_RPT_EN);
+	else
+		rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, B_AX_RXBCN_RPT_EN);
+}
+
+static void rtw89_mac_port_cfg_net_type(struct rtw89_dev *rtwdev,
+					struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->port_cfg, B_AX_NET_TYPE_MASK,
+				rtwvif->net_type);
+}
+
+static void rtw89_mac_port_cfg_bcn_prct(struct rtw89_dev *rtwdev,
+					struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+	bool en = rtwvif->net_type != RTW89_NET_TYPE_NO_LINK;
+	u32 bits = B_AX_TBTT_PROHIB_EN | B_AX_BRK_SETUP;
+
+	if (en)
+		rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, bits);
+	else
+		rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, bits);
+}
+
+static void rtw89_mac_port_cfg_rx_sw(struct rtw89_dev *rtwdev,
+				     struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+	bool en = rtwvif->net_type == RTW89_NET_TYPE_INFRA ||
+		  rtwvif->net_type == RTW89_NET_TYPE_AD_HOC;
+	u32 bit = B_AX_RX_BSSID_FIT_EN;
+
+	if (en)
+		rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, bit);
+	else
+		rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, bit);
+}
+
+static void rtw89_mac_port_cfg_rx_sync(struct rtw89_dev *rtwdev,
+				       struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+	bool en = rtwvif->net_type == RTW89_NET_TYPE_INFRA ||
+		  rtwvif->net_type == RTW89_NET_TYPE_AD_HOC;
+
+	if (en)
+		rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, B_AX_TSF_UDT_EN);
+	else
+		rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, B_AX_TSF_UDT_EN);
+}
+
+static void rtw89_mac_port_cfg_tx_sw(struct rtw89_dev *rtwdev,
+				     struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+	bool en = rtwvif->net_type == RTW89_NET_TYPE_AP_MODE ||
+		  rtwvif->net_type == RTW89_NET_TYPE_AD_HOC;
+
+	if (en)
+		rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, B_AX_BCNTX_EN);
+	else
+		rtw89_write32_port_clr(rtwdev, rtwvif, p->port_cfg, B_AX_BCNTX_EN);
+}
+
+static void rtw89_mac_port_cfg_bcn_intv(struct rtw89_dev *rtwdev,
+					struct rtw89_vif *rtwvif)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	const struct rtw89_port_reg *p = &rtw_port_base;
+	u16 bcn_int = vif->bss_conf.beacon_int ? vif->bss_conf.beacon_int : BCN_INTERVAL;
+
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->bcn_space, B_AX_BCN_SPACE_MASK,
+				bcn_int);
+}
+
+static void rtw89_mac_port_cfg_bcn_setup_time(struct rtw89_dev *rtwdev,
+					      struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->tbtt_prohib,
+				B_AX_TBTT_SETUP_MASK, BCN_SETUP_DEF);
+}
+
+static void rtw89_mac_port_cfg_bcn_hold_time(struct rtw89_dev *rtwdev,
+					     struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->tbtt_prohib,
+				B_AX_TBTT_HOLD_MASK, BCN_HOLD_DEF);
+}
+
+static void rtw89_mac_port_cfg_bcn_mask_area(struct rtw89_dev *rtwdev,
+					     struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->bcn_area,
+				B_AX_BCN_MSK_AREA_MASK, BCN_MASK_DEF);
+}
+
+static void rtw89_mac_port_cfg_tbtt_early(struct rtw89_dev *rtwdev,
+					  struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write16_port_mask(rtwdev, rtwvif, p->tbtt_early,
+				B_AX_TBTTERLY_MASK, TBTT_ERLY_DEF);
+}
+
+static void rtw89_mac_port_cfg_bss_color(struct rtw89_dev *rtwdev,
+					 struct rtw89_vif *rtwvif)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	static const u32 masks[RTW89_PORT_NUM] = {
+		B_AX_BSS_COLOB_AX_PORT_0_MASK, B_AX_BSS_COLOB_AX_PORT_1_MASK,
+		B_AX_BSS_COLOB_AX_PORT_2_MASK, B_AX_BSS_COLOB_AX_PORT_3_MASK,
+		B_AX_BSS_COLOB_AX_PORT_4_MASK,
+	};
+	u8 port = rtwvif->port;
+	u32 reg_base;
+	u32 reg;
+	u8 bss_color;
+
+	bss_color = vif->bss_conf.he_bss_color.color;
+	reg_base = port >= 4 ? R_AX_PTCL_BSS_COLOR_1 : R_AX_PTCL_BSS_COLOR_0;
+	reg = rtw89_mac_reg_by_idx(reg_base, rtwvif->mac_idx);
+	rtw89_write32_mask(rtwdev, reg, masks[port], bss_color);
+}
+
+static void rtw89_mac_port_cfg_mbssid(struct rtw89_dev *rtwdev,
+				      struct rtw89_vif *rtwvif)
+{
+	u8 port = rtwvif->port;
+	u32 reg;
+
+	if (rtwvif->net_type == RTW89_NET_TYPE_AP_MODE)
+		return;
+
+	if (port == 0) {
+		reg = rtw89_mac_reg_by_idx(R_AX_MBSSID_CTRL, rtwvif->mac_idx);
+		rtw89_write32_clr(rtwdev, reg, B_AX_P0MB_ALL_MASK);
+	}
+}
+
+static void rtw89_mac_port_cfg_hiq_drop(struct rtw89_dev *rtwdev,
+					struct rtw89_vif *rtwvif)
+{
+	u8 port = rtwvif->port;
+	u32 reg;
+	u32 val;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_MBSSID_DROP_0, rtwvif->mac_idx);
+	val = rtw89_read32(rtwdev, reg);
+	val &= ~FIELD_PREP(B_AX_PORT_DROP_4_0_MASK, BIT(port));
+	if (port == 0)
+		val &= ~BIT(0);
+	rtw89_write32(rtwdev, reg, val);
+}
+
+static void rtw89_mac_port_cfg_func_en(struct rtw89_dev *rtwdev,
+				       struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write32_port_set(rtwdev, rtwvif, p->port_cfg, B_AX_PORT_FUNC_EN);
+}
+
+static void rtw89_mac_port_cfg_bcn_early(struct rtw89_dev *rtwdev,
+					 struct rtw89_vif *rtwvif)
+{
+	const struct rtw89_port_reg *p = &rtw_port_base;
+
+	rtw89_write32_port_mask(rtwdev, rtwvif, p->bcn_early, B_AX_BCNERLY_MASK,
+				BCN_ERLY_DEF);
+}
+
+int rtw89_mac_vif_init(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	int ret;
+
+	ret = rtw89_mac_port_update(rtwdev, rtwvif);
+	if (ret)
+		return ret;
+
+	rtw89_mac_dmac_tbl_init(rtwdev, rtwvif->mac_id);
+	rtw89_mac_cmac_tbl_init(rtwdev, rtwvif->mac_id);
+
+	ret = rtw89_set_macid_pause(rtwdev, rtwvif->mac_id, false);
+	if (ret)
+		return ret;
+
+	ret = rtw89_fw_h2c_vif_maintain(rtwdev, rtwvif, RTW89_VIF_CREATE);
+	if (ret)
+		return ret;
+
+	ret = rtw89_cam_init(rtwdev, rtwvif);
+	if (ret)
+		return ret;
+
+	ret = rtw89_fw_h2c_cam(rtwdev, rtwvif);
+	if (ret)
+		return ret;
+
+	ret = rtw89_fw_h2c_default_cmac_tbl(rtwdev, rtwvif->mac_id);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+int rtw89_mac_vif_deinit(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	int ret;
+
+	ret = rtw89_fw_h2c_vif_maintain(rtwdev, rtwvif, RTW89_VIF_REMOVE);
+	if (ret)
+		return ret;
+
+	rtw89_cam_deinit(rtwdev, rtwvif);
+
+	ret = rtw89_fw_h2c_cam(rtwdev, rtwvif);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+int rtw89_mac_port_update(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	u8 port = rtwvif->port;
+
+	if (port >= RTW89_PORT_NUM)
+		return -EINVAL;
+
+	rtw89_mac_port_cfg_func_sw(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_tx_rpt(rtwdev, rtwvif, false);
+	rtw89_mac_port_cfg_rx_rpt(rtwdev, rtwvif, false);
+	rtw89_mac_port_cfg_net_type(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_bcn_prct(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_rx_sw(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_rx_sync(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_tx_sw(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_bcn_intv(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_bcn_setup_time(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_bcn_hold_time(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_bcn_mask_area(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_tbtt_early(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_bss_color(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_mbssid(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_hiq_drop(rtwdev, rtwvif);
+	rtw89_mac_port_cfg_func_en(rtwdev, rtwvif);
+	fsleep(BCN_ERLY_SET_DLY);
+	rtw89_mac_port_cfg_bcn_early(rtwdev, rtwvif);
+
+	return 0;
+}
+
+int rtw89_mac_add_vif(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	int ret;
+
+	rtwvif->mac_id = rtw89_core_acquire_bit_map(rtwdev->mac_id_map,
+						    RTW89_MAX_MAC_ID_NUM);
+	if (rtwvif->mac_id == RTW89_MAX_MAC_ID_NUM)
+		return -ENOSPC;
+
+	ret = rtw89_mac_vif_init(rtwdev, rtwvif);
+	if (ret)
+		goto release_mac_id;
+
+	return 0;
+
+release_mac_id:
+	rtw89_core_release_bit_map(rtwdev->mac_id_map, rtwvif->mac_id);
+
+	return ret;
+}
+
+int rtw89_mac_remove_vif(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	int ret;
+
+	ret = rtw89_mac_vif_deinit(rtwdev, rtwvif);
+	rtw89_core_release_bit_map(rtwdev->mac_id_map, rtwvif->mac_id);
+
+	return ret;
+}
+
+static void
+rtw89_mac_c2h_macid_pause(struct rtw89_dev *rtwdev, struct sk_buff *c2h, u32 len)
+{
+}
+
+static void
+rtw89_mac_c2h_rec_ack(struct rtw89_dev *rtwdev, struct sk_buff *c2h, u32 len)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_FW,
+		    "C2H rev ack recv, cat: %d, class: %d, func: %d, seq : %d\n",
+		    RTW89_GET_MAC_C2H_REV_ACK_CAT(c2h->data),
+		    RTW89_GET_MAC_C2H_REV_ACK_CLASS(c2h->data),
+		    RTW89_GET_MAC_C2H_REV_ACK_FUNC(c2h->data),
+		    RTW89_GET_MAC_C2H_REV_ACK_H2C_SEQ(c2h->data));
+}
+
+static void
+rtw89_mac_c2h_done_ack(struct rtw89_dev *rtwdev, struct sk_buff *c2h, u32 len)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_FW,
+		    "C2H done ack recv, cat: %d, class: %d, func: %d, ret: %d, seq : %d\n",
+		    RTW89_GET_MAC_C2H_DONE_ACK_CAT(c2h->data),
+		    RTW89_GET_MAC_C2H_DONE_ACK_CLASS(c2h->data),
+		    RTW89_GET_MAC_C2H_DONE_ACK_FUNC(c2h->data),
+		    RTW89_GET_MAC_C2H_DONE_ACK_H2C_RETURN(c2h->data),
+		    RTW89_GET_MAC_C2H_DONE_ACK_H2C_SEQ(c2h->data));
+}
+
+static void
+rtw89_mac_c2h_log(struct rtw89_dev *rtwdev, struct sk_buff *c2h, u32 len)
+{
+	rtw89_info(rtwdev, "%*s", RTW89_GET_C2H_LOG_LEN(len),
+		   RTW89_GET_C2H_LOG_SRT_PRT(c2h->data));
+}
+
+static
+void (* const rtw89_mac_c2h_ofld_handler[])(struct rtw89_dev *rtwdev,
+					    struct sk_buff *c2h, u32 len) = {
+	[RTW89_MAC_C2H_FUNC_EFUSE_DUMP] = NULL,
+	[RTW89_MAC_C2H_FUNC_READ_RSP] = NULL,
+	[RTW89_MAC_C2H_FUNC_PKT_OFLD_RSP] = NULL,
+	[RTW89_MAC_C2H_FUNC_BCN_RESEND] = NULL,
+	[RTW89_MAC_C2H_FUNC_MACID_PAUSE] = rtw89_mac_c2h_macid_pause,
+};
+
+static
+void (* const rtw89_mac_c2h_info_handler[])(struct rtw89_dev *rtwdev,
+					    struct sk_buff *c2h, u32 len) = {
+	[RTW89_MAC_C2H_FUNC_REC_ACK] = rtw89_mac_c2h_rec_ack,
+	[RTW89_MAC_C2H_FUNC_DONE_ACK] = rtw89_mac_c2h_done_ack,
+	[RTW89_MAC_C2H_FUNC_C2H_LOG] = rtw89_mac_c2h_log,
+};
+
+void rtw89_mac_c2h_handle(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			  u32 len, u8 class, u8 func)
+{
+	void (*handler)(struct rtw89_dev *rtwdev,
+			struct sk_buff *c2h, u32 len) = NULL;
+
+	switch (class) {
+	case RTW89_MAC_C2H_CLASS_INFO:
+		if (func < RTW89_MAC_C2H_FUNC_INFO_MAX)
+			handler = rtw89_mac_c2h_info_handler[func];
+		break;
+	case RTW89_MAC_C2H_CLASS_OFLD:
+		if (func < RTW89_MAC_C2H_FUNC_OFLD_MAX)
+			handler = rtw89_mac_c2h_ofld_handler[func];
+		break;
+	case RTW89_MAC_C2H_CLASS_FWDBG:
+		return;
+	default:
+		rtw89_info(rtwdev, "c2h class %d not support\n", class);
+		return;
+	}
+	if (!handler) {
+		rtw89_info(rtwdev, "c2h class %d func %d not support\n", class,
+			   func);
+		return;
+	}
+	handler(rtwdev, skb, len);
+}
+
+bool rtw89_mac_get_txpwr_cr(struct rtw89_dev *rtwdev,
+			    enum rtw89_phy_idx phy_idx,
+			    u32 reg_base, u32 *cr)
+{
+	const struct rtw89_dle_mem *dle_mem = rtwdev->chip->dle_mem;
+	enum rtw89_qta_mode mode = dle_mem->mode;
+	u32 addr = rtw89_mac_reg_by_idx(reg_base, phy_idx);
+
+	if (addr < R_AX_PWR_RATE_CTRL || addr > CMAC1_END_ADDR) {
+		rtw89_err(rtwdev, "[TXPWR] addr=0x%x exceed txpwr cr\n",
+			  addr);
+		goto error;
+	}
+
+	if (addr >= CMAC1_START_ADDR && addr <= CMAC1_END_ADDR)
+		if (mode == RTW89_QTA_SCC) {
+			rtw89_err(rtwdev,
+				  "[TXPWR] addr=0x%x but hw not enable\n",
+				  addr);
+			goto error;
+		}
+
+	*cr = addr;
+	return true;
+
+error:
+	rtw89_err(rtwdev, "[TXPWR] check txpwr cr 0x%x(phy%d) fail\n",
+		  addr, phy_idx);
+
+	return false;
+}
+
+int rtw89_mac_cfg_ppdu_status(struct rtw89_dev *rtwdev, u8 mac_idx, bool enable)
+{
+	u32 reg = rtw89_mac_reg_by_idx(R_AX_PPDU_STAT, mac_idx);
+	int ret = 0;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	if (!enable) {
+		rtw89_write32_clr(rtwdev, reg, B_AX_PPDU_STAT_RPT_EN);
+		return ret;
+	}
+
+	rtw89_write32(rtwdev, reg, B_AX_PPDU_STAT_RPT_EN |
+				   B_AX_APP_MAC_INFO_RPT |
+				   B_AX_APP_RX_CNT_RPT | B_AX_APP_PLCP_HDR_RPT |
+				   B_AX_PPDU_STAT_RPT_CRC32);
+	rtw89_write32_mask(rtwdev, R_AX_HW_RPT_FWD, B_AX_FWD_PPDU_STAT_MASK,
+			   RTW89_PRPT_DEST_HOST);
+
+	return ret;
+}
+
+void rtw89_mac_update_rts_threshold(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+#define MAC_AX_TIME_TH_SH  5
+#define MAC_AX_LEN_TH_SH   4
+#define MAC_AX_TIME_TH_MAX 255
+#define MAC_AX_LEN_TH_MAX  255
+#define MAC_AX_TIME_TH_DEF 88
+#define MAC_AX_LEN_TH_DEF  4080
+	struct ieee80211_hw *hw = rtwdev->hw;
+	u32 rts_threshold = hw->wiphy->rts_threshold;
+	u32 time_th, len_th;
+	u32 reg;
+
+	if (rts_threshold == (u32)-1) {
+		time_th = MAC_AX_TIME_TH_DEF;
+		len_th = MAC_AX_LEN_TH_DEF;
+	} else {
+		time_th = MAC_AX_TIME_TH_MAX << MAC_AX_TIME_TH_SH;
+		len_th = rts_threshold;
+	}
+
+	time_th = min_t(u32, time_th >> MAC_AX_TIME_TH_SH, MAC_AX_TIME_TH_MAX);
+	len_th = min_t(u32, len_th >> MAC_AX_LEN_TH_SH, MAC_AX_LEN_TH_MAX);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_AGG_LEN_HT_0, mac_idx);
+	rtw89_write16_mask(rtwdev, reg, B_AX_RTS_TXTIME_TH_MASK, time_th);
+	rtw89_write16_mask(rtwdev, reg, B_AX_RTS_LEN_TH_MASK, len_th);
+}
+
+void rtw89_mac_flush_txq(struct rtw89_dev *rtwdev, u32 queues, bool drop)
+{
+	bool empty;
+	int ret;
+
+	if (!test_bit(RTW89_FLAG_POWERON, rtwdev->flags))
+		return;
+
+	ret = read_poll_timeout(dle_is_txq_empty, empty, empty,
+				10000, 200000, false, rtwdev);
+	if (ret && !drop && (rtwdev->total_sta_assoc || rtwdev->scanning))
+		rtw89_info(rtwdev, "timed out to flush queues\n");
+}
+
+int rtw89_mac_coex_init(struct rtw89_dev *rtwdev, const struct rtw89_mac_ax_coex *coex)
+{
+	u8 val;
+	u16 val16;
+	u32 val32;
+	int ret;
+
+	rtw89_write8_set(rtwdev, R_AX_GPIO_MUXCFG, B_AX_ENBT);
+	rtw89_write8_set(rtwdev, R_AX_BTC_FUNC_EN, B_AX_PTA_WL_TX_EN);
+	rtw89_write8_set(rtwdev, R_AX_BT_COEX_CFG_2 + 1, B_AX_GNT_BT_POLARITY >> 8);
+	rtw89_write8_set(rtwdev, R_AX_CSR_MODE, B_AX_STATIS_BT_EN | B_AX_WL_ACT_MSK);
+	rtw89_write8_set(rtwdev, R_AX_CSR_MODE + 2, B_AX_BT_CNT_RST >> 16);
+	rtw89_write8_clr(rtwdev, R_AX_TRXPTCL_RESP_0 + 3, B_AX_RSP_CHK_BTCCA >> 24);
+
+	val16 = rtw89_read16(rtwdev, R_AX_CCA_CFG_0);
+	val16 = (val16 | B_AX_BTCCA_EN) & ~B_AX_BTCCA_BRK_TXOP_EN;
+	rtw89_write16(rtwdev, R_AX_CCA_CFG_0, val16);
+
+	ret = rtw89_mac_read_lte(rtwdev, R_AX_LTE_SW_CFG_2, &val32);
+	if (ret) {
+		rtw89_err(rtwdev, "Read R_AX_LTE_SW_CFG_2 fail!\n");
+		return ret;
+	}
+	val32 = val32 & B_AX_WL_RX_CTRL;
+	ret = rtw89_mac_write_lte(rtwdev, R_AX_LTE_SW_CFG_2, val32);
+	if (ret) {
+		rtw89_err(rtwdev, "Write R_AX_LTE_SW_CFG_2 fail!\n");
+		return ret;
+	}
+
+	switch (coex->pta_mode) {
+	case RTW89_MAC_AX_COEX_RTK_MODE:
+		val = rtw89_read8(rtwdev, R_AX_GPIO_MUXCFG);
+		val &= ~B_AX_BTMODE_MASK;
+		val |= FIELD_PREP(B_AX_BTMODE_MASK, MAC_AX_BT_MODE_0_3);
+		rtw89_write8(rtwdev, R_AX_GPIO_MUXCFG, val);
+
+		val = rtw89_read8(rtwdev, R_AX_TDMA_MODE);
+		rtw89_write8(rtwdev, R_AX_TDMA_MODE, val | B_AX_RTK_BT_ENABLE);
+
+		val = rtw89_read8(rtwdev, R_AX_BT_COEX_CFG_5);
+		val &= ~B_AX_BT_RPT_SAMPLE_RATE_MASK;
+		val |= FIELD_PREP(B_AX_BT_RPT_SAMPLE_RATE_MASK, MAC_AX_RTK_RATE);
+		rtw89_write8(rtwdev, R_AX_BT_COEX_CFG_5, val);
+		break;
+	case RTW89_MAC_AX_COEX_CSR_MODE:
+		val = rtw89_read8(rtwdev, R_AX_GPIO_MUXCFG);
+		val &= ~B_AX_BTMODE_MASK;
+		val |= FIELD_PREP(B_AX_BTMODE_MASK, MAC_AX_BT_MODE_2);
+		rtw89_write8(rtwdev, R_AX_GPIO_MUXCFG, val);
+
+		val16 = rtw89_read16(rtwdev, R_AX_CSR_MODE);
+		val16 &= ~B_AX_BT_PRI_DETECT_TO_MASK;
+		val16 |= FIELD_PREP(B_AX_BT_PRI_DETECT_TO_MASK, MAC_AX_CSR_PRI_TO);
+		val16 &= ~B_AX_BT_TRX_INIT_DETECT_MASK;
+		val16 |= FIELD_PREP(B_AX_BT_TRX_INIT_DETECT_MASK, MAC_AX_CSR_TRX_TO);
+		val16 &= ~B_AX_BT_STAT_DELAY_MASK;
+		val16 |= FIELD_PREP(B_AX_BT_STAT_DELAY_MASK, MAC_AX_CSR_DELAY);
+		val16 |= B_AX_ENHANCED_BT;
+		rtw89_write16(rtwdev, R_AX_CSR_MODE, val16);
+
+		rtw89_write8(rtwdev, R_AX_BT_COEX_CFG_2, MAC_AX_CSR_RATE);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (coex->direction) {
+	case RTW89_MAC_AX_COEX_INNER:
+		val = rtw89_read8(rtwdev, R_AX_GPIO_MUXCFG + 1);
+		val = (val & ~BIT(2)) | BIT(1);
+		rtw89_write8(rtwdev, R_AX_GPIO_MUXCFG + 1, val);
+		break;
+	case RTW89_MAC_AX_COEX_OUTPUT:
+		val = rtw89_read8(rtwdev, R_AX_GPIO_MUXCFG + 1);
+		val = val | BIT(1) | BIT(0);
+		rtw89_write8(rtwdev, R_AX_GPIO_MUXCFG + 1, val);
+		break;
+	case RTW89_MAC_AX_COEX_INPUT:
+		val = rtw89_read8(rtwdev, R_AX_GPIO_MUXCFG + 1);
+		val = val & ~(BIT(2) | BIT(1));
+		rtw89_write8(rtwdev, R_AX_GPIO_MUXCFG + 1, val);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+int rtw89_mac_cfg_gnt(struct rtw89_dev *rtwdev,
+		      const struct rtw89_mac_ax_coex_gnt *gnt_cfg)
+{
+	u32 val, ret;
+
+	ret = rtw89_mac_read_lte(rtwdev, R_AX_LTE_SW_CFG_1, &val);
+	if (ret) {
+		rtw89_err(rtwdev, "Read LTE fail!\n");
+		return ret;
+	}
+	val = (gnt_cfg->band[0].gnt_bt ?
+	       B_AX_GNT_BT_RFC_S0_SW_VAL | B_AX_GNT_BT_BB_S0_SW_VAL : 0) |
+	      (gnt_cfg->band[0].gnt_bt_sw_en ?
+	       B_AX_GNT_BT_RFC_S0_SW_CTRL | B_AX_GNT_BT_BB_S0_SW_CTRL : 0) |
+	      (gnt_cfg->band[0].gnt_wl ?
+	       B_AX_GNT_WL_RFC_S0_SW_VAL | B_AX_GNT_WL_BB_S0_SW_VAL : 0) |
+	      (gnt_cfg->band[0].gnt_wl_sw_en ?
+	       B_AX_GNT_WL_RFC_S0_SW_CTRL | B_AX_GNT_WL_BB_S0_SW_CTRL : 0) |
+	      (gnt_cfg->band[1].gnt_bt ?
+	       B_AX_GNT_BT_RFC_S1_SW_VAL | B_AX_GNT_BT_BB_S1_SW_VAL : 0) |
+	      (gnt_cfg->band[1].gnt_bt_sw_en ?
+	       B_AX_GNT_BT_RFC_S1_SW_CTRL | B_AX_GNT_BT_BB_S1_SW_CTRL : 0) |
+	      (gnt_cfg->band[1].gnt_wl ?
+	       B_AX_GNT_WL_RFC_S1_SW_VAL | B_AX_GNT_WL_BB_S1_SW_VAL : 0) |
+	      (gnt_cfg->band[1].gnt_wl_sw_en ?
+	       B_AX_GNT_WL_RFC_S1_SW_CTRL | B_AX_GNT_WL_BB_S1_SW_CTRL : 0);
+	ret = rtw89_mac_write_lte(rtwdev, R_AX_LTE_SW_CFG_1, val);
+	if (ret) {
+		rtw89_err(rtwdev, "Write LTE fail!\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+int rtw89_mac_cfg_plt(struct rtw89_dev *rtwdev, struct rtw89_mac_ax_plt *plt)
+{
+	u32 reg;
+	u8 val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, plt->band, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_BT_PLT, plt->band);
+	val = (plt->tx & RTW89_MAC_AX_PLT_LTE_RX ? B_AX_TX_PLT_GNT_LTE_RX : 0) |
+	      (plt->tx & RTW89_MAC_AX_PLT_GNT_BT_TX ? B_AX_TX_PLT_GNT_BT_TX : 0) |
+	      (plt->tx & RTW89_MAC_AX_PLT_GNT_BT_RX ? B_AX_TX_PLT_GNT_BT_RX : 0) |
+	      (plt->tx & RTW89_MAC_AX_PLT_GNT_WL ? B_AX_TX_PLT_GNT_WL : 0) |
+	      (plt->rx & RTW89_MAC_AX_PLT_LTE_RX ? B_AX_RX_PLT_GNT_LTE_RX : 0) |
+	      (plt->rx & RTW89_MAC_AX_PLT_GNT_BT_TX ? B_AX_RX_PLT_GNT_BT_TX : 0) |
+	      (plt->rx & RTW89_MAC_AX_PLT_GNT_BT_RX ? B_AX_RX_PLT_GNT_BT_RX : 0) |
+	      (plt->rx & RTW89_MAC_AX_PLT_GNT_WL ? B_AX_RX_PLT_GNT_WL : 0);
+	rtw89_write8(rtwdev, reg, val);
+
+	return 0;
+}
+
+void rtw89_mac_cfg_sb(struct rtw89_dev *rtwdev, u32 val)
+{
+	u32 fw_sb;
+
+	fw_sb = rtw89_read32(rtwdev, R_AX_SCOREBOARD);
+	fw_sb = FIELD_GET(B_MAC_AX_SB_FW_MASK, fw_sb);
+	fw_sb = fw_sb & ~B_MAC_AX_BTGS1_NOTIFY;
+	if (!test_bit(RTW89_FLAG_POWERON, rtwdev->flags))
+		fw_sb = fw_sb | MAC_AX_NOTIFY_PWR_MAJOR;
+	else
+		fw_sb = fw_sb | MAC_AX_NOTIFY_TP_MAJOR;
+	val = FIELD_GET(B_MAC_AX_SB_DRV_MASK, val);
+	val = B_AX_TOGGLE |
+	      FIELD_PREP(B_MAC_AX_SB_DRV_MASK, val) |
+	      FIELD_PREP(B_MAC_AX_SB_FW_MASK, fw_sb);
+	rtw89_write32(rtwdev, R_AX_SCOREBOARD, val);
+	fsleep(1000); /* avoid BT FW loss information */
+}
+
+u32 rtw89_mac_get_sb(struct rtw89_dev *rtwdev)
+{
+	return rtw89_read32(rtwdev, R_AX_SCOREBOARD);
+}
+
+int rtw89_mac_cfg_ctrl_path(struct rtw89_dev *rtwdev, bool wl)
+{
+	u8 val = rtw89_read8(rtwdev, R_AX_SYS_SDIO_CTRL + 3);
+
+	val = wl ? val | BIT(2) : val & ~BIT(2);
+	rtw89_write8(rtwdev, R_AX_SYS_SDIO_CTRL + 3, val);
+
+	return 0;
+}
+
+bool rtw89_mac_get_ctrl_path(struct rtw89_dev *rtwdev)
+{
+	u8 val = rtw89_read8(rtwdev, R_AX_SYS_SDIO_CTRL + 3);
+
+	return FIELD_GET(B_AX_LTE_MUX_CTRL_PATH >> 24, val);
+}
+
+static void rtw89_mac_bfee_ctrl(struct rtw89_dev *rtwdev, u8 mac_idx, bool en)
+{
+	u32 reg;
+	u32 mask = B_AX_BFMEE_HT_NDPA_EN | B_AX_BFMEE_VHT_NDPA_EN |
+		   B_AX_BFMEE_HE_NDPA_EN;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BF, "set bfee ndpa_en to %d\n", en);
+	reg = rtw89_mac_reg_by_idx(R_AX_BFMEE_RESP_OPTION, mac_idx);
+	if (en) {
+		set_bit(RTW89_FLAG_BFEE_EN, rtwdev->flags);
+		rtw89_write32_set(rtwdev, reg, mask);
+	} else {
+		clear_bit(RTW89_FLAG_BFEE_EN, rtwdev->flags);
+		rtw89_write32_clr(rtwdev, reg, mask);
+	}
+}
+
+static int rtw89_mac_init_bfee(struct rtw89_dev *rtwdev, u8 mac_idx)
+{
+	u32 reg;
+	u32 val32;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	/* AP mode set tx gid to 63 */
+	/* STA mode set tx gid to 0(default) */
+	reg = rtw89_mac_reg_by_idx(R_AX_BFMER_CTRL_0, mac_idx);
+	rtw89_write32_set(rtwdev, reg, B_AX_BFMER_NDP_BFEN);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_RRSC, mac_idx);
+	rtw89_write32(rtwdev, reg, CSI_RRSC_BMAP);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_BFMEE_RESP_OPTION, mac_idx);
+	val32 = FIELD_PREP(B_AX_BFMEE_BFRP_RX_STANDBY_TIMER_MASK, BFRP_RX_STANDBY_TIMER);
+	val32 |= FIELD_PREP(B_AX_BFMEE_NDP_RX_STANDBY_TIMER_MASK, NDP_RX_STANDBY_TIMER);
+	rtw89_write32(rtwdev, reg, val32);
+	rtw89_mac_bfee_ctrl(rtwdev, mac_idx, true);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_CTRL_0, mac_idx);
+	rtw89_write32_set(rtwdev, reg, B_AX_BFMEE_BFPARAM_SEL |
+				       B_AX_BFMEE_USE_NSTS |
+				       B_AX_BFMEE_CSI_GID_SEL |
+				       B_AX_BFMEE_CSI_FORCE_RETE_EN);
+	reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_RATE, mac_idx);
+	rtw89_write32(rtwdev, reg,
+		      u32_encode_bits(CSI_INIT_RATE_HT, B_AX_BFMEE_HT_CSI_RATE_MASK) |
+		      u32_encode_bits(CSI_INIT_RATE_VHT, B_AX_BFMEE_VHT_CSI_RATE_MASK) |
+		      u32_encode_bits(CSI_INIT_RATE_HE, B_AX_BFMEE_HE_CSI_RATE_MASK));
+
+	return 0;
+}
+
+static int rtw89_mac_set_csi_para_reg(struct rtw89_dev *rtwdev,
+				      struct ieee80211_vif *vif,
+				      struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	u8 mac_idx = rtwvif->mac_idx;
+	u8 nc = 1, nr = 3, ng = 0, cb = 1, cs = 1, ldpc_en = 1, stbc_en = 1;
+	u8 port_sel = rtwvif->port;
+	u8 sound_dim = 3, t;
+	u8 *phy_cap = sta->he_cap.he_cap_elem.phy_cap_info;
+	u32 reg;
+	u16 val;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	if ((phy_cap[3] & IEEE80211_HE_PHY_CAP3_SU_BEAMFORMER) ||
+	    (phy_cap[4] & IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER)) {
+		ldpc_en &= !!(phy_cap[1] & IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD);
+		stbc_en &= !!(phy_cap[2] & IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ);
+		t = FIELD_GET(IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_MASK,
+			      phy_cap[5]);
+		sound_dim = min(sound_dim, t);
+	}
+	if ((sta->vht_cap.cap & IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE) ||
+	    (sta->vht_cap.cap & IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE)) {
+		ldpc_en &= !!(sta->vht_cap.cap & IEEE80211_VHT_CAP_RXLDPC);
+		stbc_en &= !!(sta->vht_cap.cap & IEEE80211_VHT_CAP_RXSTBC_MASK);
+		t = FIELD_GET(IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK,
+			      sta->vht_cap.cap);
+		sound_dim = min(sound_dim, t);
+	}
+	nc = min(nc, sound_dim);
+	nr = min(nr, sound_dim);
+
+	reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_CTRL_0, mac_idx);
+	rtw89_write32_set(rtwdev, reg, B_AX_BFMEE_BFPARAM_SEL);
+
+	val = FIELD_PREP(B_AX_BFMEE_CSIINFO0_NC_MASK, nc) |
+	      FIELD_PREP(B_AX_BFMEE_CSIINFO0_NR_MASK, nr) |
+	      FIELD_PREP(B_AX_BFMEE_CSIINFO0_NG_MASK, ng) |
+	      FIELD_PREP(B_AX_BFMEE_CSIINFO0_CB_MASK, cb) |
+	      FIELD_PREP(B_AX_BFMEE_CSIINFO0_CS_MASK, cs) |
+	      FIELD_PREP(B_AX_BFMEE_CSIINFO0_LDPC_EN, ldpc_en) |
+	      FIELD_PREP(B_AX_BFMEE_CSIINFO0_STBC_EN, stbc_en);
+
+	if (port_sel == 0)
+		reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_CTRL_0, mac_idx);
+	else
+		reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_CTRL_1, mac_idx);
+
+	rtw89_write16(rtwdev, reg, val);
+
+	return 0;
+}
+
+static int rtw89_mac_csi_rrsc(struct rtw89_dev *rtwdev,
+			      struct ieee80211_vif *vif,
+			      struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	u32 rrsc = BIT(RTW89_MAC_BF_RRSC_6M) | BIT(RTW89_MAC_BF_RRSC_24M);
+	u32 reg;
+	u8 mac_idx = rtwvif->mac_idx;
+	int ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	if (sta->he_cap.has_he) {
+		rrsc |= (BIT(RTW89_MAC_BF_RRSC_HE_MSC0) |
+			 BIT(RTW89_MAC_BF_RRSC_HE_MSC3) |
+			 BIT(RTW89_MAC_BF_RRSC_HE_MSC5));
+	}
+	if (sta->vht_cap.vht_supported) {
+		rrsc |= (BIT(RTW89_MAC_BF_RRSC_VHT_MSC0) |
+			 BIT(RTW89_MAC_BF_RRSC_VHT_MSC3) |
+			 BIT(RTW89_MAC_BF_RRSC_VHT_MSC5));
+	}
+	if (sta->ht_cap.ht_supported) {
+		rrsc |= (BIT(RTW89_MAC_BF_RRSC_HT_MSC0) |
+			 BIT(RTW89_MAC_BF_RRSC_HT_MSC3) |
+			 BIT(RTW89_MAC_BF_RRSC_HT_MSC5));
+	}
+	reg = rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_CTRL_0, mac_idx);
+	rtw89_write32_set(rtwdev, reg, B_AX_BFMEE_BFPARAM_SEL);
+	rtw89_write32_clr(rtwdev, reg, B_AX_BFMEE_CSI_FORCE_RETE_EN);
+	rtw89_write32(rtwdev,
+		      rtw89_mac_reg_by_idx(R_AX_TRXPTCL_RESP_CSI_RRSC, mac_idx),
+		      rrsc);
+
+	return 0;
+}
+
+void rtw89_mac_bf_assoc(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+			struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	if (rtw89_sta_has_beamformer_cap(sta)) {
+		rtw89_debug(rtwdev, RTW89_DBG_BF,
+			    "initialize bfee for new association\n");
+		rtw89_mac_init_bfee(rtwdev, rtwvif->mac_idx);
+		rtw89_mac_set_csi_para_reg(rtwdev, vif, sta);
+		rtw89_mac_csi_rrsc(rtwdev, vif, sta);
+	}
+}
+
+void rtw89_mac_bf_disassoc(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+			   struct ieee80211_sta *sta)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	rtw89_mac_bfee_ctrl(rtwdev, rtwvif->mac_idx, false);
+}
+
+void rtw89_mac_bf_set_gid_table(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+				struct ieee80211_bss_conf *conf)
+{
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	u8 mac_idx = rtwvif->mac_idx;
+	__le32 *p;
+
+	rtw89_debug(rtwdev, RTW89_DBG_BF, "update bf GID table\n");
+
+	p = (__le32 *)conf->mu_group.membership;
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_GID_POSITION_EN0, mac_idx),
+		      le32_to_cpu(p[0]));
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_GID_POSITION_EN1, mac_idx),
+		      le32_to_cpu(p[1]));
+
+	p = (__le32 *)conf->mu_group.position;
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_GID_POSITION0, mac_idx),
+		      le32_to_cpu(p[0]));
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_GID_POSITION1, mac_idx),
+		      le32_to_cpu(p[1]));
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_GID_POSITION2, mac_idx),
+		      le32_to_cpu(p[2]));
+	rtw89_write32(rtwdev, rtw89_mac_reg_by_idx(R_AX_GID_POSITION3, mac_idx),
+		      le32_to_cpu(p[3]));
+}
+
+struct rtw89_mac_bf_monitor_iter_data {
+	struct rtw89_dev *rtwdev;
+	struct ieee80211_sta *down_sta;
+	int count;
+};
+
+static
+void rtw89_mac_bf_monitor_calc_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_mac_bf_monitor_iter_data *iter_data =
+				(struct rtw89_mac_bf_monitor_iter_data *)data;
+	struct ieee80211_sta *down_sta = iter_data->down_sta;
+	int *count = &iter_data->count;
+
+	if (down_sta == sta)
+		return;
+
+	if (rtw89_sta_has_beamformer_cap(sta))
+		(*count)++;
+}
+
+void rtw89_mac_bf_monitor_calc(struct rtw89_dev *rtwdev,
+			       struct ieee80211_sta *sta, bool disconnect)
+{
+	struct rtw89_mac_bf_monitor_iter_data data;
+
+	data.rtwdev = rtwdev;
+	data.down_sta = disconnect ? sta : NULL;
+	data.count = 0;
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_mac_bf_monitor_calc_iter,
+					  &data);
+
+	rtw89_debug(rtwdev, RTW89_DBG_BF, "bfee STA count=%d\n", data.count);
+	if (data.count)
+		set_bit(RTW89_FLAG_BFEE_MON, rtwdev->flags);
+	else
+		clear_bit(RTW89_FLAG_BFEE_MON, rtwdev->flags);
+}
+
+void _rtw89_mac_bf_monitor_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_traffic_stats *stats = &rtwdev->stats;
+	struct rtw89_vif *rtwvif;
+	bool en = stats->tx_tfc_lv > stats->rx_tfc_lv ? false : true;
+	bool old = test_bit(RTW89_FLAG_BFEE_EN, rtwdev->flags);
+
+	if (en == old)
+		return;
+
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		rtw89_mac_bfee_ctrl(rtwdev, rtwvif->mac_idx, en);
+}
+
+static int
+__rtw89_mac_set_tx_time(struct rtw89_dev *rtwdev, struct rtw89_sta *rtwsta,
+			u32 tx_time)
+{
+#define MAC_AX_DFLT_TX_TIME 5280
+	u8 mac_idx = rtwsta->rtwvif->mac_idx;
+	u32 max_tx_time = tx_time == 0 ? MAC_AX_DFLT_TX_TIME : tx_time;
+	u32 reg;
+	int ret = 0;
+
+	if (rtwsta->cctl_tx_time) {
+		rtwsta->ampdu_max_time = (max_tx_time - 512) >> 9;
+		ret = rtw89_fw_h2c_txtime_cmac_tbl(rtwdev, rtwsta);
+	} else {
+		ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+		if (ret) {
+			rtw89_warn(rtwdev, "failed to check cmac in set txtime\n");
+			return ret;
+		}
+
+		reg = rtw89_mac_reg_by_idx(R_AX_AMPDU_AGG_LIMIT, mac_idx);
+		rtw89_write32_mask(rtwdev, reg, B_AX_AMPDU_MAX_TIME_MASK,
+				   max_tx_time >> 5);
+	}
+
+	return ret;
+}
+
+int rtw89_mac_set_tx_time(struct rtw89_dev *rtwdev, struct rtw89_sta *rtwsta,
+			  bool resume, u32 tx_time)
+{
+	int ret = 0;
+
+	if (!resume) {
+		rtwsta->cctl_tx_time = true;
+		ret = __rtw89_mac_set_tx_time(rtwdev, rtwsta, tx_time);
+	} else {
+		ret = __rtw89_mac_set_tx_time(rtwdev, rtwsta, tx_time);
+		rtwsta->cctl_tx_time = false;
+	}
+
+	return ret;
+}
+
+int rtw89_mac_get_tx_time(struct rtw89_dev *rtwdev, struct rtw89_sta *rtwsta,
+			  u32 *tx_time)
+{
+	u8 mac_idx = rtwsta->rtwvif->mac_idx;
+	u32 reg;
+	int ret = 0;
+
+	if (rtwsta->cctl_tx_time) {
+		*tx_time = (rtwsta->ampdu_max_time + 1) << 9;
+	} else {
+		ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+		if (ret) {
+			rtw89_warn(rtwdev, "failed to check cmac in tx_time\n");
+			return ret;
+		}
+
+		reg = rtw89_mac_reg_by_idx(R_AX_AMPDU_AGG_LIMIT, mac_idx);
+		*tx_time = rtw89_read32_mask(rtwdev, reg, B_AX_AMPDU_MAX_TIME_MASK) << 5;
+	}
+
+	return ret;
+}
+
+int rtw89_mac_set_tx_retry_limit(struct rtw89_dev *rtwdev,
+				 struct rtw89_sta *rtwsta,
+				 bool resume, u8 tx_retry)
+{
+	int ret = 0;
+
+	rtwsta->data_tx_cnt_lmt = tx_retry;
+
+	if (!resume) {
+		rtwsta->cctl_tx_retry_limit = true;
+		ret = rtw89_fw_h2c_txtime_cmac_tbl(rtwdev, rtwsta);
+	} else {
+		ret = rtw89_fw_h2c_txtime_cmac_tbl(rtwdev, rtwsta);
+		rtwsta->cctl_tx_retry_limit = false;
+	}
+
+	return ret;
+}
+
+int rtw89_mac_get_tx_retry_limit(struct rtw89_dev *rtwdev,
+				 struct rtw89_sta *rtwsta, u8 *tx_retry)
+{
+	u8 mac_idx = rtwsta->rtwvif->mac_idx;
+	u32 reg;
+	int ret = 0;
+
+	if (rtwsta->cctl_tx_retry_limit) {
+		*tx_retry = rtwsta->data_tx_cnt_lmt;
+	} else {
+		ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+		if (ret) {
+			rtw89_warn(rtwdev, "failed to check cmac in rty_lmt\n");
+			return ret;
+		}
+
+		reg = rtw89_mac_reg_by_idx(R_AX_TXCNT, mac_idx);
+		*tx_retry = rtw89_read32_mask(rtwdev, reg, B_AX_L_TXCNT_LMT_MASK);
+	}
+
+	return ret;
+}
+
+int rtw89_mac_set_hw_muedca_ctrl(struct rtw89_dev *rtwdev,
+				 struct rtw89_vif *rtwvif, bool en)
+{
+	u8 mac_idx = rtwvif->mac_idx;
+	u16 set = B_AX_MUEDCA_EN_0 | B_AX_SET_MUEDCATIMER_TF_0;
+	u32 reg;
+	u32 ret;
+
+	ret = rtw89_mac_check_mac_en(rtwdev, mac_idx, RTW89_CMAC_SEL);
+	if (ret)
+		return ret;
+
+	reg = rtw89_mac_reg_by_idx(R_AX_MUEDCA_EN, mac_idx);
+	if (en)
+		rtw89_write16_set(rtwdev, reg, set);
+	else
+		rtw89_write16_clr(rtwdev, reg, set);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/mac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/mac.h
@@ -0,0 +1,860 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_MAC_H__
+#define __RTW89_MAC_H__
+
+#include "core.h"
+
+#define MAC_MEM_DUMP_PAGE_SIZE 0x40000
+#define ADDR_CAM_ENT_SIZE  0x40
+#define BSSID_CAM_ENT_SIZE 0x08
+#define HFC_PAGE_UNIT 64
+
+enum rtw89_mac_hwmod_sel {
+	RTW89_DMAC_SEL = 0,
+	RTW89_CMAC_SEL = 1,
+
+	RTW89_MAC_INVALID,
+};
+
+enum rtw89_mac_fwd_target {
+	RTW89_FWD_DONT_CARE    = 0,
+	RTW89_FWD_TO_HOST      = 1,
+	RTW89_FWD_TO_WLAN_CPU  = 2
+};
+
+enum rtw89_mac_wd_dma_intvl {
+	RTW89_MAC_WD_DMA_INTVL_0S,
+	RTW89_MAC_WD_DMA_INTVL_256NS,
+	RTW89_MAC_WD_DMA_INTVL_512NS,
+	RTW89_MAC_WD_DMA_INTVL_768NS,
+	RTW89_MAC_WD_DMA_INTVL_1US,
+	RTW89_MAC_WD_DMA_INTVL_1_5US,
+	RTW89_MAC_WD_DMA_INTVL_2US,
+	RTW89_MAC_WD_DMA_INTVL_4US,
+	RTW89_MAC_WD_DMA_INTVL_8US,
+	RTW89_MAC_WD_DMA_INTVL_16US,
+	RTW89_MAC_WD_DMA_INTVL_DEF = 0xFE
+};
+
+enum rtw89_mac_multi_tag_num {
+	RTW89_MAC_TAG_NUM_1,
+	RTW89_MAC_TAG_NUM_2,
+	RTW89_MAC_TAG_NUM_3,
+	RTW89_MAC_TAG_NUM_4,
+	RTW89_MAC_TAG_NUM_5,
+	RTW89_MAC_TAG_NUM_6,
+	RTW89_MAC_TAG_NUM_7,
+	RTW89_MAC_TAG_NUM_8,
+	RTW89_MAC_TAG_NUM_DEF = 0xFE
+};
+
+enum rtw89_mac_lbc_tmr {
+	RTW89_MAC_LBC_TMR_8US = 0,
+	RTW89_MAC_LBC_TMR_16US,
+	RTW89_MAC_LBC_TMR_32US,
+	RTW89_MAC_LBC_TMR_64US,
+	RTW89_MAC_LBC_TMR_128US,
+	RTW89_MAC_LBC_TMR_256US,
+	RTW89_MAC_LBC_TMR_512US,
+	RTW89_MAC_LBC_TMR_1MS,
+	RTW89_MAC_LBC_TMR_2MS,
+	RTW89_MAC_LBC_TMR_4MS,
+	RTW89_MAC_LBC_TMR_8MS,
+	RTW89_MAC_LBC_TMR_DEF = 0xFE
+};
+
+enum rtw89_mac_cpuio_op_cmd_type {
+	CPUIO_OP_CMD_GET_1ST_PID = 0,
+	CPUIO_OP_CMD_GET_NEXT_PID = 1,
+	CPUIO_OP_CMD_ENQ_TO_TAIL = 4,
+	CPUIO_OP_CMD_ENQ_TO_HEAD = 5,
+	CPUIO_OP_CMD_DEQ = 8,
+	CPUIO_OP_CMD_DEQ_ENQ_ALL = 9,
+	CPUIO_OP_CMD_DEQ_ENQ_TO_TAIL = 12
+};
+
+enum rtw89_mac_wde_dle_port_id {
+	WDE_DLE_PORT_ID_DISPATCH = 0,
+	WDE_DLE_PORT_ID_PKTIN = 1,
+	WDE_DLE_PORT_ID_CMAC0 = 3,
+	WDE_DLE_PORT_ID_CMAC1 = 4,
+	WDE_DLE_PORT_ID_CPU_IO = 6,
+	WDE_DLE_PORT_ID_WDRLS = 7,
+	WDE_DLE_PORT_ID_END = 8
+};
+
+enum rtw89_mac_wde_dle_queid_wdrls {
+	WDE_DLE_QUEID_TXOK = 0,
+	WDE_DLE_QUEID_DROP_RETRY_LIMIT = 1,
+	WDE_DLE_QUEID_DROP_LIFETIME_TO = 2,
+	WDE_DLE_QUEID_DROP_MACID_DROP = 3,
+	WDE_DLE_QUEID_NO_REPORT = 4
+};
+
+enum rtw89_mac_ple_dle_port_id {
+	PLE_DLE_PORT_ID_DISPATCH = 0,
+	PLE_DLE_PORT_ID_MPDU = 1,
+	PLE_DLE_PORT_ID_SEC = 2,
+	PLE_DLE_PORT_ID_CMAC0 = 3,
+	PLE_DLE_PORT_ID_CMAC1 = 4,
+	PLE_DLE_PORT_ID_WDRLS = 5,
+	PLE_DLE_PORT_ID_CPU_IO = 6,
+	PLE_DLE_PORT_ID_PLRLS = 7,
+	PLE_DLE_PORT_ID_END = 8
+};
+
+enum rtw89_mac_ple_dle_queid_plrls {
+	PLE_DLE_QUEID_NO_REPORT = 0x0
+};
+
+enum rtw89_machdr_frame_type {
+	RTW89_MGNT = 0,
+	RTW89_CTRL = 1,
+	RTW89_DATA = 2,
+};
+
+enum rtw89_mac_dle_dfi_type {
+	DLE_DFI_TYPE_FREEPG	= 0,
+	DLE_DFI_TYPE_QUOTA	= 1,
+	DLE_DFI_TYPE_PAGELLT	= 2,
+	DLE_DFI_TYPE_PKTINFO	= 3,
+	DLE_DFI_TYPE_PREPKTLLT	= 4,
+	DLE_DFI_TYPE_NXTPKTLLT	= 5,
+	DLE_DFI_TYPE_QLNKTBL	= 6,
+	DLE_DFI_TYPE_QEMPTY	= 7,
+};
+
+enum rtw89_mac_dle_wde_quota_id {
+	WDE_QTAID_HOST_IF = 0,
+	WDE_QTAID_WLAN_CPU = 1,
+	WDE_QTAID_DATA_CPU = 2,
+	WDE_QTAID_PKTIN = 3,
+	WDE_QTAID_CPUIO = 4,
+};
+
+enum rtw89_mac_dle_ple_quota_id {
+	PLE_QTAID_B0_TXPL = 0,
+	PLE_QTAID_B1_TXPL = 1,
+	PLE_QTAID_C2H = 2,
+	PLE_QTAID_H2C = 3,
+	PLE_QTAID_WLAN_CPU = 4,
+	PLE_QTAID_MPDU = 5,
+	PLE_QTAID_CMAC0_RX = 6,
+	PLE_QTAID_CMAC1_RX = 7,
+	PLE_QTAID_CMAC1_BBRPT = 8,
+	PLE_QTAID_WDRLS = 9,
+	PLE_QTAID_CPUIO = 10,
+};
+
+enum rtw89_mac_dle_ctrl_type {
+	DLE_CTRL_TYPE_WDE = 0,
+	DLE_CTRL_TYPE_PLE = 1,
+	DLE_CTRL_TYPE_NUM = 2,
+};
+
+enum rtw89_mac_ax_l0_to_l1_event {
+	MAC_AX_L0_TO_L1_CHIF_IDLE = 0,
+	MAC_AX_L0_TO_L1_CMAC_DMA_IDLE = 1,
+	MAC_AX_L0_TO_L1_RLS_PKID = 2,
+	MAC_AX_L0_TO_L1_PTCL_IDLE = 3,
+	MAC_AX_L0_TO_L1_RX_QTA_LOST = 4,
+	MAC_AX_L0_TO_L1_DLE_STAT_HANG = 5,
+	MAC_AX_L0_TO_L1_PCIE_STUCK = 6,
+	MAC_AX_L0_TO_L1_EVENT_MAX = 15,
+};
+
+enum rtw89_mac_dbg_port_sel {
+	/* CMAC 0 related */
+	RTW89_DBG_PORT_SEL_PTCL_C0 = 0,
+	RTW89_DBG_PORT_SEL_SCH_C0,
+	RTW89_DBG_PORT_SEL_TMAC_C0,
+	RTW89_DBG_PORT_SEL_RMAC_C0,
+	RTW89_DBG_PORT_SEL_RMACST_C0,
+	RTW89_DBG_PORT_SEL_RMAC_PLCP_C0,
+	RTW89_DBG_PORT_SEL_TRXPTCL_C0,
+	RTW89_DBG_PORT_SEL_TX_INFOL_C0,
+	RTW89_DBG_PORT_SEL_TX_INFOH_C0,
+	RTW89_DBG_PORT_SEL_TXTF_INFOL_C0,
+	RTW89_DBG_PORT_SEL_TXTF_INFOH_C0,
+	/* CMAC 1 related */
+	RTW89_DBG_PORT_SEL_PTCL_C1,
+	RTW89_DBG_PORT_SEL_SCH_C1,
+	RTW89_DBG_PORT_SEL_TMAC_C1,
+	RTW89_DBG_PORT_SEL_RMAC_C1,
+	RTW89_DBG_PORT_SEL_RMACST_C1,
+	RTW89_DBG_PORT_SEL_RMAC_PLCP_C1,
+	RTW89_DBG_PORT_SEL_TRXPTCL_C1,
+	RTW89_DBG_PORT_SEL_TX_INFOL_C1,
+	RTW89_DBG_PORT_SEL_TX_INFOH_C1,
+	RTW89_DBG_PORT_SEL_TXTF_INFOL_C1,
+	RTW89_DBG_PORT_SEL_TXTF_INFOH_C1,
+	/* DLE related */
+	RTW89_DBG_PORT_SEL_WDE_BUFMGN_FREEPG,
+	RTW89_DBG_PORT_SEL_WDE_BUFMGN_QUOTA,
+	RTW89_DBG_PORT_SEL_WDE_BUFMGN_PAGELLT,
+	RTW89_DBG_PORT_SEL_WDE_BUFMGN_PKTINFO,
+	RTW89_DBG_PORT_SEL_WDE_QUEMGN_PREPKT,
+	RTW89_DBG_PORT_SEL_WDE_QUEMGN_NXTPKT,
+	RTW89_DBG_PORT_SEL_WDE_QUEMGN_QLNKTBL,
+	RTW89_DBG_PORT_SEL_WDE_QUEMGN_QEMPTY,
+	RTW89_DBG_PORT_SEL_PLE_BUFMGN_FREEPG,
+	RTW89_DBG_PORT_SEL_PLE_BUFMGN_QUOTA,
+	RTW89_DBG_PORT_SEL_PLE_BUFMGN_PAGELLT,
+	RTW89_DBG_PORT_SEL_PLE_BUFMGN_PKTINFO,
+	RTW89_DBG_PORT_SEL_PLE_QUEMGN_PREPKT,
+	RTW89_DBG_PORT_SEL_PLE_QUEMGN_NXTPKT,
+	RTW89_DBG_PORT_SEL_PLE_QUEMGN_QLNKTBL,
+	RTW89_DBG_PORT_SEL_PLE_QUEMGN_QEMPTY,
+	RTW89_DBG_PORT_SEL_PKTINFO,
+	/* PCIE related */
+	RTW89_DBG_PORT_SEL_PCIE_TXDMA,
+	RTW89_DBG_PORT_SEL_PCIE_RXDMA,
+	RTW89_DBG_PORT_SEL_PCIE_CVT,
+	RTW89_DBG_PORT_SEL_PCIE_CXPL,
+	RTW89_DBG_PORT_SEL_PCIE_IO,
+	RTW89_DBG_PORT_SEL_PCIE_MISC,
+	RTW89_DBG_PORT_SEL_PCIE_MISC2,
+
+	/* keep last */
+	RTW89_DBG_PORT_SEL_LAST,
+	RTW89_DBG_PORT_SEL_MAX = RTW89_DBG_PORT_SEL_LAST,
+	RTW89_DBG_PORT_SEL_INVALID = RTW89_DBG_PORT_SEL_LAST,
+};
+
+/* SRAM mem dump */
+#define R_AX_INDIR_ACCESS_ENTRY 0x40000
+
+#define	STA_SCHED_BASE_ADDR		0x18808000
+#define	RXPLD_FLTR_CAM_BASE_ADDR	0x18813000
+#define	SECURITY_CAM_BASE_ADDR		0x18814000
+#define	WOW_CAM_BASE_ADDR		0x18815000
+#define	CMAC_TBL_BASE_ADDR		0x18840000
+#define	ADDR_CAM_BASE_ADDR		0x18850000
+#define	BSSID_CAM_BASE_ADDR		0x18853000
+#define	BA_CAM_BASE_ADDR		0x18854000
+#define	BCN_IE_CAM0_BASE_ADDR		0x18855000
+#define	SHARED_BUF_BASE_ADDR		0x18700000
+#define	DMAC_TBL_BASE_ADDR		0x18800000
+#define	SHCUT_MACHDR_BASE_ADDR		0x18800800
+#define	BCN_IE_CAM1_BASE_ADDR		0x188A0000
+
+#define CCTL_INFO_SIZE		32
+
+enum rtw89_mac_mem_sel {
+	RTW89_MAC_MEM_SHARED_BUF,
+	RTW89_MAC_MEM_DMAC_TBL,
+	RTW89_MAC_MEM_SHCUT_MACHDR,
+	RTW89_MAC_MEM_STA_SCHED,
+	RTW89_MAC_MEM_RXPLD_FLTR_CAM,
+	RTW89_MAC_MEM_SECURITY_CAM,
+	RTW89_MAC_MEM_WOW_CAM,
+	RTW89_MAC_MEM_CMAC_TBL,
+	RTW89_MAC_MEM_ADDR_CAM,
+	RTW89_MAC_MEM_BA_CAM,
+	RTW89_MAC_MEM_BCN_IE_CAM0,
+	RTW89_MAC_MEM_BCN_IE_CAM1,
+
+	/* keep last */
+	RTW89_MAC_MEM_LAST,
+	RTW89_MAC_MEM_MAX = RTW89_MAC_MEM_LAST,
+	RTW89_MAC_MEM_INVALID = RTW89_MAC_MEM_LAST,
+};
+
+enum rtw89_rpwm_req_pwr_state {
+	RTW89_MAC_RPWM_REQ_PWR_STATE_ACTIVE = 0,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_BAND0_RFON = 1,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_BAND1_RFON = 2,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_BAND0_RFOFF = 3,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_BAND1_RFOFF = 4,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_CLK_GATED = 5,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_PWR_GATED = 6,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_HIOE_PWR_GATED = 7,
+	RTW89_MAC_RPWM_REQ_PWR_STATE_MAX,
+};
+
+struct rtw89_pwr_cfg {
+	u16 addr;
+	u8 cv_msk;
+	u8 intf_msk;
+	u8 base:4;
+	u8 cmd:4;
+	u8 msk;
+	u8 val;
+};
+
+enum rtw89_mac_c2h_ofld_func {
+	RTW89_MAC_C2H_FUNC_EFUSE_DUMP,
+	RTW89_MAC_C2H_FUNC_READ_RSP,
+	RTW89_MAC_C2H_FUNC_PKT_OFLD_RSP,
+	RTW89_MAC_C2H_FUNC_BCN_RESEND,
+	RTW89_MAC_C2H_FUNC_MACID_PAUSE,
+	RTW89_MAC_C2H_FUNC_OFLD_MAX,
+};
+
+enum rtw89_mac_c2h_info_func {
+	RTW89_MAC_C2H_FUNC_REC_ACK,
+	RTW89_MAC_C2H_FUNC_DONE_ACK,
+	RTW89_MAC_C2H_FUNC_C2H_LOG,
+	RTW89_MAC_C2H_FUNC_INFO_MAX,
+};
+
+enum rtw89_mac_c2h_class {
+	RTW89_MAC_C2H_CLASS_INFO,
+	RTW89_MAC_C2H_CLASS_OFLD,
+	RTW89_MAC_C2H_CLASS_TWT,
+	RTW89_MAC_C2H_CLASS_WOW,
+	RTW89_MAC_C2H_CLASS_MCC,
+	RTW89_MAC_C2H_CLASS_FWDBG,
+	RTW89_MAC_C2H_CLASS_MAX,
+};
+
+struct rtw89_mac_ax_coex {
+#define RTW89_MAC_AX_COEX_RTK_MODE 0
+#define RTW89_MAC_AX_COEX_CSR_MODE 1
+	u8 pta_mode;
+#define RTW89_MAC_AX_COEX_INNER 0
+#define RTW89_MAC_AX_COEX_OUTPUT 1
+#define RTW89_MAC_AX_COEX_INPUT 2
+	u8 direction;
+};
+
+struct rtw89_mac_ax_plt {
+#define RTW89_MAC_AX_PLT_LTE_RX BIT(0)
+#define RTW89_MAC_AX_PLT_GNT_BT_TX BIT(1)
+#define RTW89_MAC_AX_PLT_GNT_BT_RX BIT(2)
+#define RTW89_MAC_AX_PLT_GNT_WL BIT(3)
+	u8 band;
+	u8 tx;
+	u8 rx;
+};
+
+enum rtw89_mac_bf_rrsc_rate {
+	RTW89_MAC_BF_RRSC_6M = 0,
+	RTW89_MAC_BF_RRSC_9M = 1,
+	RTW89_MAC_BF_RRSC_12M,
+	RTW89_MAC_BF_RRSC_18M,
+	RTW89_MAC_BF_RRSC_24M,
+	RTW89_MAC_BF_RRSC_36M,
+	RTW89_MAC_BF_RRSC_48M,
+	RTW89_MAC_BF_RRSC_54M,
+	RTW89_MAC_BF_RRSC_HT_MSC0,
+	RTW89_MAC_BF_RRSC_HT_MSC1,
+	RTW89_MAC_BF_RRSC_HT_MSC2,
+	RTW89_MAC_BF_RRSC_HT_MSC3,
+	RTW89_MAC_BF_RRSC_HT_MSC4,
+	RTW89_MAC_BF_RRSC_HT_MSC5,
+	RTW89_MAC_BF_RRSC_HT_MSC6,
+	RTW89_MAC_BF_RRSC_HT_MSC7,
+	RTW89_MAC_BF_RRSC_VHT_MSC0,
+	RTW89_MAC_BF_RRSC_VHT_MSC1,
+	RTW89_MAC_BF_RRSC_VHT_MSC2,
+	RTW89_MAC_BF_RRSC_VHT_MSC3,
+	RTW89_MAC_BF_RRSC_VHT_MSC4,
+	RTW89_MAC_BF_RRSC_VHT_MSC5,
+	RTW89_MAC_BF_RRSC_VHT_MSC6,
+	RTW89_MAC_BF_RRSC_VHT_MSC7,
+	RTW89_MAC_BF_RRSC_HE_MSC0,
+	RTW89_MAC_BF_RRSC_HE_MSC1,
+	RTW89_MAC_BF_RRSC_HE_MSC2,
+	RTW89_MAC_BF_RRSC_HE_MSC3,
+	RTW89_MAC_BF_RRSC_HE_MSC4,
+	RTW89_MAC_BF_RRSC_HE_MSC5,
+	RTW89_MAC_BF_RRSC_HE_MSC6,
+	RTW89_MAC_BF_RRSC_HE_MSC7 = 31,
+	RTW89_MAC_BF_RRSC_MAX = 32
+};
+
+#define RTW89_R32_EA		0xEAEAEAEA
+#define RTW89_R32_DEAD		0xDEADBEEF
+#define MAC_REG_POOL_COUNT	10
+#define ACCESS_CMAC(_addr) \
+	({typeof(_addr) __addr = (_addr); \
+	  __addr >= R_AX_CMAC_REG_START && __addr <= R_AX_CMAC_REG_END; })
+
+#define PTCL_IDLE_POLL_CNT	10000
+#define SW_CVR_DUR_US	8
+#define SW_CVR_CNT	8
+
+#define DLE_BOUND_UNIT (8 * 1024)
+#define DLE_WAIT_CNT 2000
+#define TRXCFG_WAIT_CNT	2000
+
+#define RTW89_WDE_PG_64		64
+#define RTW89_WDE_PG_128	128
+#define RTW89_WDE_PG_256	256
+
+#define S_AX_WDE_PAGE_SEL_64	0
+#define S_AX_WDE_PAGE_SEL_128	1
+#define S_AX_WDE_PAGE_SEL_256	2
+
+#define RTW89_PLE_PG_64		64
+#define RTW89_PLE_PG_128	128
+#define RTW89_PLE_PG_256	256
+
+#define S_AX_PLE_PAGE_SEL_64	0
+#define S_AX_PLE_PAGE_SEL_128	1
+#define S_AX_PLE_PAGE_SEL_256	2
+
+#define SDIO_LOCAL_BASE_ADDR    0x80000000
+
+#define	PWR_CMD_WRITE		0
+#define	PWR_CMD_POLL		1
+#define	PWR_CMD_DELAY		2
+#define	PWR_CMD_END		3
+
+#define	PWR_INTF_MSK_SDIO	BIT(0)
+#define	PWR_INTF_MSK_USB	BIT(1)
+#define	PWR_INTF_MSK_PCIE	BIT(2)
+#define	PWR_INTF_MSK_ALL	0x7
+
+#define PWR_BASE_MAC		0
+#define PWR_BASE_USB		1
+#define PWR_BASE_PCIE		2
+#define PWR_BASE_SDIO		3
+
+#define	PWR_CV_MSK_A		BIT(0)
+#define	PWR_CV_MSK_B		BIT(1)
+#define	PWR_CV_MSK_C		BIT(2)
+#define	PWR_CV_MSK_D		BIT(3)
+#define	PWR_CV_MSK_E		BIT(4)
+#define	PWR_CV_MSK_F		BIT(5)
+#define	PWR_CV_MSK_G		BIT(6)
+#define	PWR_CV_MSK_TEST		BIT(7)
+#define	PWR_CV_MSK_ALL		0xFF
+
+#define	PWR_DELAY_US		0
+#define	PWR_DELAY_MS		1
+
+/* STA scheduler */
+#define SS_MACID_SH		8
+#define SS_TX_LEN_MSK		0x1FFFFF
+#define SS_CTRL1_R_TX_LEN	5
+#define SS_CTRL1_R_NEXT_LINK	20
+#define SS_LINK_SIZE		256
+
+/* MAC debug port */
+#define TMAC_DBG_SEL_C0 0xA5
+#define RMAC_DBG_SEL_C0 0xA6
+#define TRXPTCL_DBG_SEL_C0 0xA7
+#define TMAC_DBG_SEL_C1 0xB5
+#define RMAC_DBG_SEL_C1 0xB6
+#define TRXPTCL_DBG_SEL_C1 0xB7
+#define FW_PROG_CNTR_DBG_SEL 0xF2
+#define PCIE_TXDMA_DBG_SEL 0x30
+#define PCIE_RXDMA_DBG_SEL 0x31
+#define PCIE_CVT_DBG_SEL 0x32
+#define PCIE_CXPL_DBG_SEL 0x33
+#define PCIE_IO_DBG_SEL 0x37
+#define PCIE_MISC_DBG_SEL 0x38
+#define PCIE_MISC2_DBG_SEL 0x00
+#define MAC_DBG_SEL 1
+#define RMAC_CMAC_DBG_SEL 1
+
+/* TRXPTCL dbg port sel */
+#define TRXPTRL_DBG_SEL_TMAC 0
+#define TRXPTRL_DBG_SEL_RMAC 1
+
+struct rtw89_cpuio_ctrl {
+	u16 pkt_num;
+	u16 start_pktid;
+	u16 end_pktid;
+	u8 cmd_type;
+	u8 macid;
+	u8 src_pid;
+	u8 src_qid;
+	u8 dst_pid;
+	u8 dst_qid;
+	u16 pktid;
+};
+
+struct rtw89_mac_dbg_port_info {
+	u32 sel_addr;
+	u8 sel_byte;
+	u32 sel_msk;
+	u32 srt;
+	u32 end;
+	u32 rd_addr;
+	u8 rd_byte;
+	u32 rd_msk;
+};
+
+#define QLNKTBL_ADDR_INFO_SEL BIT(0)
+#define QLNKTBL_ADDR_INFO_SEL_0 0
+#define QLNKTBL_ADDR_INFO_SEL_1 1
+#define QLNKTBL_ADDR_TBL_IDX_MASK GENMASK(10, 1)
+#define QLNKTBL_DATA_SEL1_PKT_CNT_MASK GENMASK(11, 0)
+
+struct rtw89_mac_dle_dfi_ctrl {
+	enum rtw89_mac_dle_ctrl_type type;
+	u32 target;
+	u32 addr;
+	u32 out_data;
+};
+
+struct rtw89_mac_dle_dfi_quota {
+	enum rtw89_mac_dle_ctrl_type dle_type;
+	u32 qtaid;
+	u16 rsv_pgnum;
+	u16 use_pgnum;
+};
+
+struct rtw89_mac_dle_dfi_qempty {
+	enum rtw89_mac_dle_ctrl_type dle_type;
+	u32 grpsel;
+	u32 qempty;
+};
+
+/* Define DBG and recovery enum */
+enum mac_ax_err_info {
+	/* Get error info */
+
+	/* L0 */
+	MAC_AX_ERR_L0_ERR_CMAC0 = 0x0001,
+	MAC_AX_ERR_L0_ERR_CMAC1 = 0x0002,
+	MAC_AX_ERR_L0_RESET_DONE = 0x0003,
+	MAC_AX_ERR_L0_PROMOTE_TO_L1 = 0x0010,
+
+	/* L1 */
+	MAC_AX_ERR_L1_ERR_DMAC = 0x1000,
+	MAC_AX_ERR_L1_RESET_DISABLE_DMAC_DONE = 0x1001,
+	MAC_AX_ERR_L1_RESET_RECOVERY_DONE = 0x1002,
+	MAC_AX_ERR_L1_PROMOTE_TO_L2 = 0x1010,
+	MAC_AX_ERR_L1_RCVY_STOP_DONE = 0x1011,
+
+	/* L2 */
+	/* address hole (master) */
+	MAC_AX_ERR_L2_ERR_AH_DMA = 0x2000,
+	MAC_AX_ERR_L2_ERR_AH_HCI = 0x2010,
+	MAC_AX_ERR_L2_ERR_AH_RLX4081 = 0x2020,
+	MAC_AX_ERR_L2_ERR_AH_IDDMA = 0x2030,
+	MAC_AX_ERR_L2_ERR_AH_HIOE = 0x2040,
+	MAC_AX_ERR_L2_ERR_AH_IPSEC = 0x2050,
+	MAC_AX_ERR_L2_ERR_AH_RX4281 = 0x2060,
+	MAC_AX_ERR_L2_ERR_AH_OTHERS = 0x2070,
+
+	/* AHB bridge timeout (master) */
+	MAC_AX_ERR_L2_ERR_AHB_TO_DMA = 0x2100,
+	MAC_AX_ERR_L2_ERR_AHB_TO_HCI = 0x2110,
+	MAC_AX_ERR_L2_ERR_AHB_TO_RLX4081 = 0x2120,
+	MAC_AX_ERR_L2_ERR_AHB_TO_IDDMA = 0x2130,
+	MAC_AX_ERR_L2_ERR_AHB_TO_HIOE = 0x2140,
+	MAC_AX_ERR_L2_ERR_AHB_TO_IPSEC = 0x2150,
+	MAC_AX_ERR_L2_ERR_AHB_TO_RX4281 = 0x2160,
+	MAC_AX_ERR_L2_ERR_AHB_TO_OTHERS = 0x2170,
+
+	/* APB_SA bridge timeout (master + slave) */
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_WVA = 0x2200,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_UART = 0x2201,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_CPULOCAL = 0x2202,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_AXIDMA = 0x2203,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_HIOE = 0x2204,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_IDDMA = 0x2205,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_IPSEC = 0x2206,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_WON = 0x2207,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_WDMAC = 0x2208,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_WCMAC = 0x2209,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_DMA_OTHERS = 0x220A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_WVA = 0x2210,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_UART = 0x2211,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_CPULOCAL = 0x2212,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_AXIDMA = 0x2213,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_HIOE = 0x2214,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_IDDMA = 0x2215,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_IPSEC = 0x2216,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_WDMAC = 0x2218,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_WCMAC = 0x2219,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HCI_OTHERS = 0x221A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_WVA = 0x2220,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_UART = 0x2221,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_CPULOCAL = 0x2222,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_AXIDMA = 0x2223,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_HIOE = 0x2224,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_IDDMA = 0x2225,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_IPSEC = 0x2226,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_WON = 0x2227,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_WDMAC = 0x2228,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_WCMAC = 0x2229,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RLX4081_OTHERS = 0x222A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_WVA = 0x2230,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_UART = 0x2231,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_CPULOCAL = 0x2232,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_AXIDMA = 0x2233,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_HIOE = 0x2234,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_IDDMA = 0x2235,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_IPSEC = 0x2236,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_WON = 0x2237,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_WDMAC = 0x2238,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_WCMAC = 0x2239,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IDDMA_OTHERS = 0x223A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_WVA = 0x2240,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_UART = 0x2241,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_CPULOCAL = 0x2242,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_AXIDMA = 0x2243,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_HIOE = 0x2244,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_IDDMA = 0x2245,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_IPSEC = 0x2246,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_WON = 0x2247,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_WDMAC = 0x2248,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_WCMAC = 0x2249,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_HIOE_OTHERS = 0x224A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_WVA = 0x2250,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_UART = 0x2251,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_CPULOCAL = 0x2252,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_AXIDMA = 0x2253,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_HIOE = 0x2254,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_IDDMA = 0x2255,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_IPSEC = 0x2256,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_WON = 0x2257,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_WDMAC = 0x2258,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_WCMAC = 0x2259,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_IPSEC_OTHERS = 0x225A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_WVA = 0x2260,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_UART = 0x2261,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_CPULOCAL = 0x2262,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_AXIDMA = 0x2263,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_HIOE = 0x2264,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_IDDMA = 0x2265,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_IPSEC = 0x2266,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_WON = 0x2267,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_WDMAC = 0x2268,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_WCMAC = 0x2269,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_RX4281_OTHERS = 0x226A,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_WVA = 0x2270,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_UART = 0x2271,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_CPULOCAL = 0x2272,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_AXIDMA = 0x2273,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_HIOE = 0x2274,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_IDDMA = 0x2275,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_IPSEC = 0x2276,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_WON = 0x2277,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_WDMAC = 0x2278,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_WCMAC = 0x2279,
+	MAC_AX_ERR_L2_ERR_APB_SA_TO_OTHERS_OTHERS = 0x227A,
+
+	/* APB_BBRF bridge timeout (master) */
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_DMA = 0x2300,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_HCI = 0x2310,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_RLX4081 = 0x2320,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_IDDMA = 0x2330,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_HIOE = 0x2340,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_IPSEC = 0x2350,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_RX4281 = 0x2360,
+	MAC_AX_ERR_L2_ERR_APB_BBRF_TO_OTHERS = 0x2370,
+	MAC_AX_ERR_L2_RESET_DONE = 0x2400,
+	MAC_AX_ERR_CPU_EXCEPTION = 0x3000,
+	MAC_AX_GET_ERR_MAX,
+	MAC_AX_DUMP_SHAREBUFF_INDICATOR = 0x80000000,
+
+	/* set error info */
+	MAC_AX_ERR_L1_DISABLE_EN = 0x0001,
+	MAC_AX_ERR_L1_RCVY_EN = 0x0002,
+	MAC_AX_ERR_L1_RCVY_STOP_REQ = 0x0003,
+	MAC_AX_ERR_L1_RCVY_START_REQ = 0x0004,
+	MAC_AX_ERR_L0_CFG_NOTIFY = 0x0010,
+	MAC_AX_ERR_L0_CFG_DIS_NOTIFY = 0x0011,
+	MAC_AX_ERR_L0_CFG_HANDSHAKE = 0x0012,
+	MAC_AX_ERR_L0_RCVY_EN = 0x0013,
+	MAC_AX_SET_ERR_MAX,
+};
+
+extern const struct rtw89_hfc_prec_cfg rtw_hfc_preccfg_pcie;
+extern const struct rtw89_dle_size wde_size0;
+extern const struct rtw89_dle_size wde_size4;
+extern const struct rtw89_dle_size ple_size0;
+extern const struct rtw89_dle_size ple_size4;
+extern const struct rtw89_wde_quota wde_qt0;
+extern const struct rtw89_wde_quota wde_qt4;
+extern const struct rtw89_ple_quota ple_qt4;
+extern const struct rtw89_ple_quota ple_qt5;
+extern const struct rtw89_ple_quota ple_qt13;
+
+static inline u32 rtw89_mac_reg_by_idx(u32 reg_base, u8 band)
+{
+	return band == 0 ? reg_base : (reg_base + 0x2000);
+}
+
+static inline u32 rtw89_mac_reg_by_port(u32 base, u8 port, u8 mac_idx)
+{
+	return rtw89_mac_reg_by_idx(base + port * 0x40, mac_idx);
+}
+
+static inline u32
+rtw89_read32_port_mask(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+		       u32 base, u32 mask)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	return rtw89_read32_mask(rtwdev, reg, mask);
+}
+
+static inline void
+rtw89_write32_port(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif, u32 base,
+		   u32 data)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	rtw89_write32(rtwdev, reg, data);
+}
+
+static inline void
+rtw89_write32_port_mask(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			u32 base, u32 mask, u32 data)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	rtw89_write32_mask(rtwdev, reg, mask, data);
+}
+
+static inline void
+rtw89_write16_port_mask(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+			u32 base, u32 mask, u16 data)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	rtw89_write16_mask(rtwdev, reg, mask, data);
+}
+
+static inline void
+rtw89_write32_port_clr(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+		       u32 base, u32 bit)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	rtw89_write32_clr(rtwdev, reg, bit);
+}
+
+static inline void
+rtw89_write16_port_clr(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+		       u32 base, u16 bit)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	rtw89_write16_clr(rtwdev, reg, bit);
+}
+
+static inline void
+rtw89_write32_port_set(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif,
+		       u32 base, u32 bit)
+{
+	u32 reg;
+
+	reg = rtw89_mac_reg_by_port(base, rtwvif->port, rtwvif->mac_idx);
+	rtw89_write32_set(rtwdev, reg, bit);
+}
+
+void rtw89_mac_pwr_off(struct rtw89_dev *rtwdev);
+int rtw89_mac_partial_init(struct rtw89_dev *rtwdev);
+int rtw89_mac_init(struct rtw89_dev *rtwdev);
+int rtw89_mac_check_mac_en(struct rtw89_dev *rtwdev, u8 band,
+			   enum rtw89_mac_hwmod_sel sel);
+int rtw89_mac_write_lte(struct rtw89_dev *rtwdev, const u32 offset, u32 val);
+int rtw89_mac_read_lte(struct rtw89_dev *rtwdev, const u32 offset, u32 *val);
+int rtw89_mac_add_vif(struct rtw89_dev *rtwdev, struct rtw89_vif *vif);
+int rtw89_mac_port_update(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif);
+int rtw89_mac_remove_vif(struct rtw89_dev *rtwdev, struct rtw89_vif *vif);
+void rtw89_mac_enable_bb_rf(struct rtw89_dev *rtwdev);
+void rtw89_mac_disable_bb_rf(struct rtw89_dev *rtwdev);
+u32 rtw89_mac_get_err_status(struct rtw89_dev *rtwdev);
+int rtw89_mac_set_err_status(struct rtw89_dev *rtwdev, u32 err);
+void rtw89_mac_c2h_handle(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			  u32 len, u8 class, u8 func);
+int rtw89_mac_setup_phycap(struct rtw89_dev *rtwdev);
+int rtw89_mac_stop_sch_tx(struct rtw89_dev *rtwdev, u8 mac_idx,
+			  u16 *tx_en, enum rtw89_sch_tx_sel sel);
+int rtw89_mac_resume_sch_tx(struct rtw89_dev *rtwdev, u8 mac_idx, u16 tx_en);
+int rtw89_mac_cfg_ppdu_status(struct rtw89_dev *rtwdev, u8 mac_ids, bool enable);
+void rtw89_mac_update_rts_threshold(struct rtw89_dev *rtwdev, u8 mac_idx);
+void rtw89_mac_flush_txq(struct rtw89_dev *rtwdev, u32 queues, bool drop);
+int rtw89_mac_coex_init(struct rtw89_dev *rtwdev, const struct rtw89_mac_ax_coex *coex);
+int rtw89_mac_cfg_gnt(struct rtw89_dev *rtwdev,
+		      const struct rtw89_mac_ax_coex_gnt *gnt_cfg);
+int rtw89_mac_cfg_plt(struct rtw89_dev *rtwdev, struct rtw89_mac_ax_plt *plt);
+void rtw89_mac_cfg_sb(struct rtw89_dev *rtwdev, u32 val);
+u32 rtw89_mac_get_sb(struct rtw89_dev *rtwdev);
+bool rtw89_mac_get_ctrl_path(struct rtw89_dev *rtwdev);
+int rtw89_mac_cfg_ctrl_path(struct rtw89_dev *rtwdev, bool wl);
+bool rtw89_mac_get_txpwr_cr(struct rtw89_dev *rtwdev,
+			    enum rtw89_phy_idx phy_idx,
+			    u32 reg_base, u32 *cr);
+void rtw89_mac_power_mode_change(struct rtw89_dev *rtwdev, bool enter);
+void rtw89_mac_bf_assoc(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+			struct ieee80211_sta *sta);
+void rtw89_mac_bf_disassoc(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+			   struct ieee80211_sta *sta);
+void rtw89_mac_bf_set_gid_table(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif,
+				struct ieee80211_bss_conf *conf);
+void rtw89_mac_bf_monitor_calc(struct rtw89_dev *rtwdev,
+			       struct ieee80211_sta *sta, bool disconnect);
+void _rtw89_mac_bf_monitor_track(struct rtw89_dev *rtwdev);
+int rtw89_mac_vif_init(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif);
+int rtw89_mac_vif_deinit(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif);
+int rtw89_mac_set_hw_muedca_ctrl(struct rtw89_dev *rtwdev,
+				 struct rtw89_vif *rtwvif, bool en);
+
+static inline void rtw89_mac_bf_monitor_track(struct rtw89_dev *rtwdev)
+{
+	if (!test_bit(RTW89_FLAG_BFEE_MON, rtwdev->flags))
+		return;
+
+	_rtw89_mac_bf_monitor_track(rtwdev);
+}
+
+static inline int rtw89_mac_txpwr_read32(struct rtw89_dev *rtwdev,
+					 enum rtw89_phy_idx phy_idx,
+					 u32 reg_base, u32 *val)
+{
+	u32 cr;
+
+	if (!rtw89_mac_get_txpwr_cr(rtwdev, phy_idx, reg_base, &cr))
+		return -EINVAL;
+
+	*val = rtw89_read32(rtwdev, cr);
+	return 0;
+}
+
+static inline int rtw89_mac_txpwr_write32(struct rtw89_dev *rtwdev,
+					  enum rtw89_phy_idx phy_idx,
+					  u32 reg_base, u32 val)
+{
+	u32 cr;
+
+	if (!rtw89_mac_get_txpwr_cr(rtwdev, phy_idx, reg_base, &cr))
+		return -EINVAL;
+
+	rtw89_write32(rtwdev, cr, val);
+	return 0;
+}
+
+static inline int rtw89_mac_txpwr_write32_mask(struct rtw89_dev *rtwdev,
+					       enum rtw89_phy_idx phy_idx,
+					       u32 reg_base, u32 mask, u32 val)
+{
+	u32 cr;
+
+	if (!rtw89_mac_get_txpwr_cr(rtwdev, phy_idx, reg_base, &cr))
+		return -EINVAL;
+
+	rtw89_write32_mask(rtwdev, cr, mask, val);
+	return 0;
+}
+
+int rtw89_mac_set_tx_time(struct rtw89_dev *rtwdev, struct rtw89_sta *rtwsta,
+			  bool resume, u32 tx_time);
+int rtw89_mac_get_tx_time(struct rtw89_dev *rtwdev, struct rtw89_sta *rtwsta,
+			  u32 *tx_time);
+int rtw89_mac_set_tx_retry_limit(struct rtw89_dev *rtwdev,
+				 struct rtw89_sta *rtwsta,
+				 bool resume, u8 tx_retry);
+int rtw89_mac_get_tx_retry_limit(struct rtw89_dev *rtwdev,
+				 struct rtw89_sta *rtwsta, u8 *tx_retry);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/mac80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/mac80211.c
@@ -0,0 +1,676 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "cam.h"
+#include "coex.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+#include "phy.h"
+#include "ps.h"
+#include "reg.h"
+#include "sar.h"
+#include "ser.h"
+
+static void rtw89_ops_tx(struct ieee80211_hw *hw,
+			 struct ieee80211_tx_control *control,
+			 struct sk_buff *skb)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+	struct ieee80211_vif *vif = info->control.vif;
+	struct ieee80211_sta *sta = control->sta;
+	int ret, qsel;
+
+	ret = rtw89_core_tx_write(rtwdev, vif, sta, skb, &qsel);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to transmit skb: %d\n", ret);
+		ieee80211_free_txskb(hw, skb);
+	}
+	rtw89_core_tx_kick_off(rtwdev, qsel);
+}
+
+static void rtw89_ops_wake_tx_queue(struct ieee80211_hw *hw,
+				    struct ieee80211_txq *txq)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	ieee80211_schedule_txq(hw, txq);
+	queue_work(rtwdev->txq_wq, &rtwdev->txq_work);
+}
+
+static int rtw89_ops_start(struct ieee80211_hw *hw)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	int ret;
+
+	mutex_lock(&rtwdev->mutex);
+	ret = rtw89_core_start(rtwdev);
+	mutex_unlock(&rtwdev->mutex);
+
+	return ret;
+}
+
+static void rtw89_ops_stop(struct ieee80211_hw *hw)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_core_stop(rtwdev);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static int rtw89_ops_config(struct ieee80211_hw *hw, u32 changed)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+
+	if ((changed & IEEE80211_CONF_CHANGE_IDLE) &&
+	    !(hw->conf.flags & IEEE80211_CONF_IDLE))
+		rtw89_leave_ips(rtwdev);
+
+	if (changed & IEEE80211_CONF_CHANGE_PS) {
+		if (hw->conf.flags & IEEE80211_CONF_PS) {
+			rtwdev->lps_enabled = true;
+		} else {
+			rtw89_leave_lps(rtwdev);
+			rtwdev->lps_enabled = false;
+		}
+	}
+
+	if (changed & IEEE80211_CONF_CHANGE_CHANNEL)
+		rtw89_set_channel(rtwdev);
+
+	if ((changed & IEEE80211_CONF_CHANGE_IDLE) &&
+	    (hw->conf.flags & IEEE80211_CONF_IDLE))
+		rtw89_enter_ips(rtwdev);
+
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static int rtw89_ops_add_interface(struct ieee80211_hw *hw,
+				   struct ieee80211_vif *vif)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	int ret = 0;
+
+	mutex_lock(&rtwdev->mutex);
+	list_add_tail(&rtwvif->list, &rtwdev->rtwvifs_list);
+	rtw89_leave_ps_mode(rtwdev);
+
+	rtw89_traffic_stats_init(rtwdev, &rtwvif->stats);
+	rtw89_vif_type_mapping(vif, false);
+	rtwvif->port = rtw89_core_acquire_bit_map(rtwdev->hw_port,
+						  RTW89_MAX_HW_PORT_NUM);
+	if (rtwvif->port == RTW89_MAX_HW_PORT_NUM) {
+		ret = -ENOSPC;
+		goto out;
+	}
+
+	rtwvif->bcn_hit_cond = 0;
+	rtwvif->mac_idx = RTW89_MAC_0;
+	rtwvif->phy_idx = RTW89_PHY_0;
+	rtwvif->hit_rule = 0;
+	ether_addr_copy(rtwvif->mac_addr, vif->addr);
+
+	ret = rtw89_mac_add_vif(rtwdev, rtwvif);
+	if (ret) {
+		rtw89_core_release_bit_map(rtwdev->hw_port, rtwvif->port);
+		goto out;
+	}
+
+	rtw89_core_txq_init(rtwdev, vif->txq);
+
+	rtw89_btc_ntfy_role_info(rtwdev, rtwvif, NULL, BTC_ROLE_START);
+out:
+	mutex_unlock(&rtwdev->mutex);
+
+	return ret;
+}
+
+static void rtw89_ops_remove_interface(struct ieee80211_hw *hw,
+				       struct ieee80211_vif *vif)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	rtw89_btc_ntfy_role_info(rtwdev, rtwvif, NULL, BTC_ROLE_STOP);
+	rtw89_mac_remove_vif(rtwdev, rtwvif);
+	rtw89_core_release_bit_map(rtwdev->hw_port, rtwvif->port);
+	list_del_init(&rtwvif->list);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static void rtw89_ops_configure_filter(struct ieee80211_hw *hw,
+				       unsigned int changed_flags,
+				       unsigned int *new_flags,
+				       u64 multicast)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+
+	*new_flags &= FIF_ALLMULTI | FIF_OTHER_BSS | FIF_FCSFAIL |
+		      FIF_BCN_PRBRESP_PROMISC;
+
+	if (changed_flags & FIF_ALLMULTI) {
+		if (*new_flags & FIF_ALLMULTI)
+			rtwdev->hal.rx_fltr &= ~B_AX_A_MC;
+		else
+			rtwdev->hal.rx_fltr |= B_AX_A_MC;
+	}
+	if (changed_flags & FIF_FCSFAIL) {
+		if (*new_flags & FIF_FCSFAIL)
+			rtwdev->hal.rx_fltr |= B_AX_A_CRC32_ERR;
+		else
+			rtwdev->hal.rx_fltr &= ~B_AX_A_CRC32_ERR;
+	}
+	if (changed_flags & FIF_OTHER_BSS) {
+		if (*new_flags & FIF_OTHER_BSS)
+			rtwdev->hal.rx_fltr &= ~B_AX_A_A1_MATCH;
+		else
+			rtwdev->hal.rx_fltr |= B_AX_A_A1_MATCH;
+	}
+	if (changed_flags & FIF_BCN_PRBRESP_PROMISC) {
+		if (*new_flags & FIF_BCN_PRBRESP_PROMISC) {
+			rtwdev->hal.rx_fltr &= ~B_AX_A_BCN_CHK_EN;
+			rtwdev->hal.rx_fltr &= ~B_AX_A_BC;
+			rtwdev->hal.rx_fltr &= ~B_AX_A_A1_MATCH;
+		} else {
+			rtwdev->hal.rx_fltr |= B_AX_A_BCN_CHK_EN;
+			rtwdev->hal.rx_fltr |= B_AX_A_BC;
+			rtwdev->hal.rx_fltr |= B_AX_A_A1_MATCH;
+		}
+	}
+
+	rtw89_write32_mask(rtwdev,
+			   rtw89_mac_reg_by_idx(R_AX_RX_FLTR_OPT, RTW89_MAC_0),
+			   B_AX_RX_FLTR_CFG_MASK,
+			   rtwdev->hal.rx_fltr);
+	if (!rtwdev->dbcc_en)
+		goto out;
+	rtw89_write32_mask(rtwdev,
+			   rtw89_mac_reg_by_idx(R_AX_RX_FLTR_OPT, RTW89_MAC_1),
+			   B_AX_RX_FLTR_CFG_MASK,
+			   rtwdev->hal.rx_fltr);
+
+out:
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static const u8 ac_to_fw_idx[IEEE80211_NUM_ACS] = {
+	[IEEE80211_AC_VO] = 3,
+	[IEEE80211_AC_VI] = 2,
+	[IEEE80211_AC_BE] = 0,
+	[IEEE80211_AC_BK] = 1,
+};
+
+static u8 rtw89_aifsn_to_aifs(struct rtw89_dev *rtwdev,
+			      struct rtw89_vif *rtwvif, u8 aifsn)
+{
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwvif);
+	u8 slot_time;
+	u8 sifs;
+
+	slot_time = vif->bss_conf.use_short_slot ? 9 : 20;
+	sifs = rtwdev->hal.current_band_type == RTW89_BAND_5G ? 16 : 10;
+
+	return aifsn * slot_time + sifs;
+}
+
+static void ____rtw89_conf_tx_edca(struct rtw89_dev *rtwdev,
+				   struct rtw89_vif *rtwvif, u16 ac)
+{
+	struct ieee80211_tx_queue_params *params = &rtwvif->tx_params[ac];
+	u32 val;
+	u8 ecw_max, ecw_min;
+	u8 aifs;
+
+	/* 2^ecw - 1 = cw; ecw = log2(cw + 1) */
+	ecw_max = ilog2(params->cw_max + 1);
+	ecw_min = ilog2(params->cw_min + 1);
+	aifs = rtw89_aifsn_to_aifs(rtwdev, rtwvif, params->aifs);
+	val = FIELD_PREP(FW_EDCA_PARAM_TXOPLMT_MSK, params->txop) |
+	      FIELD_PREP(FW_EDCA_PARAM_CWMAX_MSK, ecw_max) |
+	      FIELD_PREP(FW_EDCA_PARAM_CWMIN_MSK, ecw_min) |
+	      FIELD_PREP(FW_EDCA_PARAM_AIFS_MSK, aifs);
+	rtw89_fw_h2c_set_edca(rtwdev, rtwvif, ac_to_fw_idx[ac], val);
+}
+
+static const u32 ac_to_mu_edca_param[IEEE80211_NUM_ACS] = {
+	[IEEE80211_AC_VO] = R_AX_MUEDCA_VO_PARAM_0,
+	[IEEE80211_AC_VI] = R_AX_MUEDCA_VI_PARAM_0,
+	[IEEE80211_AC_BE] = R_AX_MUEDCA_BE_PARAM_0,
+	[IEEE80211_AC_BK] = R_AX_MUEDCA_BK_PARAM_0,
+};
+
+static void ____rtw89_conf_tx_mu_edca(struct rtw89_dev *rtwdev,
+				      struct rtw89_vif *rtwvif, u16 ac)
+{
+	struct ieee80211_tx_queue_params *params = &rtwvif->tx_params[ac];
+	struct ieee80211_he_mu_edca_param_ac_rec *mu_edca;
+	u8 aifs, aifsn;
+	u16 timer_32us;
+	u32 reg;
+	u32 val;
+
+	if (!params->mu_edca)
+		return;
+
+	mu_edca = &params->mu_edca_param_rec;
+	aifsn = FIELD_GET(GENMASK(3, 0), mu_edca->aifsn);
+	aifs = aifsn ? rtw89_aifsn_to_aifs(rtwdev, rtwvif, aifsn) : 0;
+	timer_32us = mu_edca->mu_edca_timer << 8;
+
+	val = FIELD_PREP(B_AX_MUEDCA_BE_PARAM_0_TIMER_MASK, timer_32us) |
+	      FIELD_PREP(B_AX_MUEDCA_BE_PARAM_0_CW_MASK, mu_edca->ecw_min_max) |
+	      FIELD_PREP(B_AX_MUEDCA_BE_PARAM_0_AIFS_MASK, aifs);
+	reg = rtw89_mac_reg_by_idx(ac_to_mu_edca_param[ac], rtwvif->mac_idx);
+	rtw89_write32(rtwdev, reg, val);
+
+	rtw89_mac_set_hw_muedca_ctrl(rtwdev, rtwvif, true);
+}
+
+static void __rtw89_conf_tx(struct rtw89_dev *rtwdev,
+			    struct rtw89_vif *rtwvif, u16 ac)
+{
+	____rtw89_conf_tx_edca(rtwdev, rtwvif, ac);
+	____rtw89_conf_tx_mu_edca(rtwdev, rtwvif, ac);
+}
+
+static void rtw89_conf_tx(struct rtw89_dev *rtwdev,
+			  struct rtw89_vif *rtwvif)
+{
+	u16 ac;
+
+	for (ac = 0; ac < IEEE80211_NUM_ACS; ac++)
+		__rtw89_conf_tx(rtwdev, rtwvif, ac);
+}
+
+static void rtw89_station_mode_sta_assoc(struct rtw89_dev *rtwdev,
+					 struct ieee80211_vif *vif,
+					 struct ieee80211_bss_conf *conf)
+{
+	struct ieee80211_sta *sta;
+
+	if (vif->type != NL80211_IFTYPE_STATION)
+		return;
+
+	sta = ieee80211_find_sta(vif, conf->bssid);
+	if (!sta) {
+		rtw89_err(rtwdev, "can't find sta to set sta_assoc state\n");
+		return;
+	}
+	rtw89_core_sta_assoc(rtwdev, vif, sta);
+}
+
+static void rtw89_ops_bss_info_changed(struct ieee80211_hw *hw,
+				       struct ieee80211_vif *vif,
+				       struct ieee80211_bss_conf *conf,
+				       u32 changed)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+
+	if (changed & BSS_CHANGED_ASSOC) {
+		if (conf->assoc) {
+			rtw89_station_mode_sta_assoc(rtwdev, vif, conf);
+			rtw89_phy_set_bss_color(rtwdev, vif);
+			rtw89_chip_cfg_txpwr_ul_tb_offset(rtwdev, vif);
+			rtw89_mac_port_update(rtwdev, rtwvif);
+		}
+	}
+
+	if (changed & BSS_CHANGED_BSSID) {
+		ether_addr_copy(rtwvif->bssid, conf->bssid);
+		rtw89_cam_bssid_changed(rtwdev, rtwvif);
+		rtw89_fw_h2c_cam(rtwdev, rtwvif);
+	}
+
+	if (changed & BSS_CHANGED_ERP_SLOT)
+		rtw89_conf_tx(rtwdev, rtwvif);
+
+	if (changed & BSS_CHANGED_HE_BSS_COLOR)
+		rtw89_phy_set_bss_color(rtwdev, vif);
+
+	if (changed & BSS_CHANGED_MU_GROUPS)
+		rtw89_mac_bf_set_gid_table(rtwdev, vif, conf);
+
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static int rtw89_ops_conf_tx(struct ieee80211_hw *hw,
+			     struct ieee80211_vif *vif, u16 ac,
+			     const struct ieee80211_tx_queue_params *params)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	rtwvif->tx_params[ac] = *params;
+	__rtw89_conf_tx(rtwdev, rtwvif, ac);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static int __rtw89_ops_sta_state(struct ieee80211_hw *hw,
+				 struct ieee80211_vif *vif,
+				 struct ieee80211_sta *sta,
+				 enum ieee80211_sta_state old_state,
+				 enum ieee80211_sta_state new_state)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	if (old_state == IEEE80211_STA_NOTEXIST &&
+	    new_state == IEEE80211_STA_NONE)
+		return rtw89_core_sta_add(rtwdev, vif, sta);
+
+	if (old_state == IEEE80211_STA_AUTH &&
+	    new_state == IEEE80211_STA_ASSOC) {
+		if (vif->type == NL80211_IFTYPE_STATION)
+			return 0; /* defer to bss_info_changed to have vif info */
+		return rtw89_core_sta_assoc(rtwdev, vif, sta);
+	}
+
+	if (old_state == IEEE80211_STA_ASSOC &&
+	    new_state == IEEE80211_STA_AUTH)
+		return rtw89_core_sta_disassoc(rtwdev, vif, sta);
+
+	if (old_state == IEEE80211_STA_AUTH &&
+	    new_state == IEEE80211_STA_NONE)
+		return rtw89_core_sta_disconnect(rtwdev, vif, sta);
+
+	if (old_state == IEEE80211_STA_NONE &&
+	    new_state == IEEE80211_STA_NOTEXIST)
+		return rtw89_core_sta_remove(rtwdev, vif, sta);
+
+	return 0;
+}
+
+static int rtw89_ops_sta_state(struct ieee80211_hw *hw,
+			       struct ieee80211_vif *vif,
+			       struct ieee80211_sta *sta,
+			       enum ieee80211_sta_state old_state,
+			       enum ieee80211_sta_state new_state)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	int ret;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	ret = __rtw89_ops_sta_state(hw, vif, sta, old_state, new_state);
+	mutex_unlock(&rtwdev->mutex);
+
+	return ret;
+}
+
+static int rtw89_ops_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
+			     struct ieee80211_vif *vif,
+			     struct ieee80211_sta *sta,
+			     struct ieee80211_key_conf *key)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	int ret = 0;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+
+	switch (cmd) {
+	case SET_KEY:
+		rtw89_btc_ntfy_specific_packet(rtwdev, PACKET_EAPOL_END);
+		ret = rtw89_cam_sec_key_add(rtwdev, vif, sta, key);
+		if (ret && ret != -EOPNOTSUPP) {
+			rtw89_err(rtwdev, "failed to add key to sec cam\n");
+			goto out;
+		}
+		break;
+	case DISABLE_KEY:
+		rtw89_hci_flush_queues(rtwdev, BIT(rtwdev->hw->queues) - 1,
+				       false);
+		rtw89_mac_flush_txq(rtwdev, BIT(rtwdev->hw->queues) - 1, false);
+		ret = rtw89_cam_sec_key_del(rtwdev, vif, sta, key, true);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to remove key from sec cam\n");
+			goto out;
+		}
+		break;
+	}
+
+out:
+	mutex_unlock(&rtwdev->mutex);
+
+	return ret;
+}
+
+static int rtw89_ops_ampdu_action(struct ieee80211_hw *hw,
+				  struct ieee80211_vif *vif,
+				  struct ieee80211_ampdu_params *params)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct ieee80211_sta *sta = params->sta;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	u16 tid = params->tid;
+	struct ieee80211_txq *txq = sta->txq[tid];
+	struct rtw89_txq *rtwtxq = (struct rtw89_txq *)txq->drv_priv;
+
+	switch (params->action) {
+	case IEEE80211_AMPDU_TX_START:
+		return IEEE80211_AMPDU_TX_START_IMMEDIATE;
+	case IEEE80211_AMPDU_TX_STOP_CONT:
+	case IEEE80211_AMPDU_TX_STOP_FLUSH:
+	case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT:
+		mutex_lock(&rtwdev->mutex);
+		clear_bit(RTW89_TXQ_F_AMPDU, &rtwtxq->flags);
+		rtw89_fw_h2c_ba_cam(rtwdev, false, rtwsta->mac_id, params);
+		mutex_unlock(&rtwdev->mutex);
+		ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
+		break;
+	case IEEE80211_AMPDU_TX_OPERATIONAL:
+		mutex_lock(&rtwdev->mutex);
+		set_bit(RTW89_TXQ_F_AMPDU, &rtwtxq->flags);
+		rtwsta->ampdu_params[tid].agg_num = params->buf_size;
+		rtwsta->ampdu_params[tid].amsdu = params->amsdu;
+		rtw89_leave_ps_mode(rtwdev);
+		rtw89_fw_h2c_ba_cam(rtwdev, true, rtwsta->mac_id, params);
+		mutex_unlock(&rtwdev->mutex);
+		break;
+	case IEEE80211_AMPDU_RX_START:
+	case IEEE80211_AMPDU_RX_STOP:
+		break;
+	default:
+		WARN_ON(1);
+		return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
+static int rtw89_ops_set_rts_threshold(struct ieee80211_hw *hw, u32 value)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+	if (test_bit(RTW89_FLAG_POWERON, rtwdev->flags))
+		rtw89_mac_update_rts_threshold(rtwdev, RTW89_MAC_0);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static void rtw89_ops_sta_statistics(struct ieee80211_hw *hw,
+				     struct ieee80211_vif *vif,
+				     struct ieee80211_sta *sta,
+				     struct station_info *sinfo)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+
+	sinfo->txrate = rtwsta->ra_report.txrate;
+	sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_BITRATE);
+}
+
+static void rtw89_ops_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			    u32 queues, bool drop)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_lps(rtwdev);
+	rtw89_hci_flush_queues(rtwdev, queues, drop);
+	rtw89_mac_flush_txq(rtwdev, queues, drop);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+struct rtw89_iter_bitrate_mask_data {
+	struct rtw89_dev *rtwdev;
+	struct ieee80211_vif *vif;
+	const struct cfg80211_bitrate_mask *mask;
+};
+
+static void rtw89_ra_mask_info_update_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_iter_bitrate_mask_data *br_data = data;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct ieee80211_vif *vif = rtwvif_to_vif(rtwsta->rtwvif);
+
+	if (vif != br_data->vif)
+		return;
+
+	rtwsta->use_cfg_mask = true;
+	rtwsta->mask = *br_data->mask;
+	rtw89_phy_ra_updata_sta(br_data->rtwdev, sta);
+}
+
+static void rtw89_ra_mask_info_update(struct rtw89_dev *rtwdev,
+				      struct ieee80211_vif *vif,
+				      const struct cfg80211_bitrate_mask *mask)
+{
+	struct rtw89_iter_bitrate_mask_data br_data = { .rtwdev = rtwdev,
+							.vif = vif,
+							.mask = mask};
+
+	ieee80211_iterate_stations_atomic(rtwdev->hw, rtw89_ra_mask_info_update_iter,
+					  &br_data);
+}
+
+static int rtw89_ops_set_bitrate_mask(struct ieee80211_hw *hw,
+				      struct ieee80211_vif *vif,
+				      const struct cfg80211_bitrate_mask *mask)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_phy_rate_pattern_vif(rtwdev, vif, mask);
+	rtw89_ra_mask_info_update(rtwdev, vif, mask);
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static
+int rtw89_ops_set_antenna(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_hal *hal = &rtwdev->hal;
+
+	if (rx_ant != hw->wiphy->available_antennas_rx)
+		return -EINVAL;
+
+	mutex_lock(&rtwdev->mutex);
+	hal->antenna_tx = tx_ant;
+	hal->antenna_rx = rx_ant;
+	mutex_unlock(&rtwdev->mutex);
+
+	return 0;
+}
+
+static
+int rtw89_ops_get_antenna(struct ieee80211_hw *hw,  u32 *tx_ant, u32 *rx_ant)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_hal *hal = &rtwdev->hal;
+
+	*tx_ant = hal->antenna_tx;
+	*rx_ant = hal->antenna_rx;
+
+	return 0;
+}
+
+static void rtw89_ops_sw_scan_start(struct ieee80211_hw *hw,
+				    struct ieee80211_vif *vif,
+				    const u8 *mac_addr)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_hal *hal = &rtwdev->hal;
+
+	mutex_lock(&rtwdev->mutex);
+	rtwdev->scanning = true;
+	rtw89_leave_lps(rtwdev);
+	rtw89_btc_ntfy_scan_start(rtwdev, RTW89_PHY_0, hal->current_band_type);
+	rtw89_chip_rfk_scan(rtwdev, true);
+	rtw89_hci_recalc_int_mit(rtwdev);
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static void rtw89_ops_sw_scan_complete(struct ieee80211_hw *hw,
+				       struct ieee80211_vif *vif)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_chip_rfk_scan(rtwdev, false);
+	rtw89_btc_ntfy_scan_finish(rtwdev, RTW89_PHY_0);
+	rtwdev->scanning = false;
+	rtwdev->dig.bypass_dig = true;
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static void rtw89_ops_reconfig_complete(struct ieee80211_hw *hw,
+					enum ieee80211_reconfig_type reconfig_type)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	if (reconfig_type == IEEE80211_RECONFIG_TYPE_RESTART)
+		rtw89_ser_recfg_done(rtwdev);
+}
+
+const struct ieee80211_ops rtw89_ops = {
+	.tx			= rtw89_ops_tx,
+	.wake_tx_queue		= rtw89_ops_wake_tx_queue,
+	.start			= rtw89_ops_start,
+	.stop			= rtw89_ops_stop,
+	.config			= rtw89_ops_config,
+	.add_interface		= rtw89_ops_add_interface,
+	.remove_interface	= rtw89_ops_remove_interface,
+	.configure_filter	= rtw89_ops_configure_filter,
+	.bss_info_changed	= rtw89_ops_bss_info_changed,
+	.conf_tx		= rtw89_ops_conf_tx,
+	.sta_state		= rtw89_ops_sta_state,
+	.set_key		= rtw89_ops_set_key,
+	.ampdu_action		= rtw89_ops_ampdu_action,
+	.set_rts_threshold	= rtw89_ops_set_rts_threshold,
+	.sta_statistics		= rtw89_ops_sta_statistics,
+	.flush			= rtw89_ops_flush,
+	.set_bitrate_mask	= rtw89_ops_set_bitrate_mask,
+	.set_antenna		= rtw89_ops_set_antenna,
+	.get_antenna		= rtw89_ops_get_antenna,
+	.sw_scan_start		= rtw89_ops_sw_scan_start,
+	.sw_scan_complete	= rtw89_ops_sw_scan_complete,
+	.reconfig_complete	= rtw89_ops_reconfig_complete,
+	.set_sar_specs		= rtw89_ops_set_sar_specs,
+};
+EXPORT_SYMBOL(rtw89_ops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/pci.c
@@ -0,0 +1,3060 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2020  Realtek Corporation
+ */
+
+#include <linux/pci.h>
+
+#include "mac.h"
+#include "pci.h"
+#include "reg.h"
+#include "ser.h"
+
+static bool rtw89_pci_disable_clkreq;
+static bool rtw89_pci_disable_aspm_l1;
+static bool rtw89_pci_disable_l1ss;
+module_param_named(disable_clkreq, rtw89_pci_disable_clkreq, bool, 0644);
+module_param_named(disable_aspm_l1, rtw89_pci_disable_aspm_l1, bool, 0644);
+module_param_named(disable_aspm_l1ss, rtw89_pci_disable_l1ss, bool, 0644);
+MODULE_PARM_DESC(disable_clkreq, "Set Y to disable PCI clkreq support");
+MODULE_PARM_DESC(disable_aspm_l1, "Set Y to disable PCI ASPM L1 support");
+MODULE_PARM_DESC(disable_aspm_l1ss, "Set Y to disable PCI L1SS support");
+
+static int rtw89_pci_rst_bdram_pcie(struct rtw89_dev *rtwdev)
+{
+	u32 val;
+	int ret;
+
+	rtw89_write32(rtwdev, R_AX_PCIE_INIT_CFG1,
+		      rtw89_read32(rtwdev, R_AX_PCIE_INIT_CFG1) | B_AX_RST_BDRAM);
+
+	ret = read_poll_timeout_atomic(rtw89_read32, val, !(val & B_AX_RST_BDRAM),
+				       1, RTW89_PCI_POLL_BDRAM_RST_CNT, false,
+				       rtwdev, R_AX_PCIE_INIT_CFG1);
+
+	if (ret)
+		return -EBUSY;
+
+	return 0;
+}
+
+static u32 rtw89_pci_dma_recalc(struct rtw89_dev *rtwdev,
+				struct rtw89_pci_dma_ring *bd_ring,
+				u32 cur_idx, bool tx)
+{
+	u32 cnt, cur_rp, wp, rp, len;
+
+	rp = bd_ring->rp;
+	wp = bd_ring->wp;
+	len = bd_ring->len;
+
+	cur_rp = FIELD_GET(TXBD_HW_IDX_MASK, cur_idx);
+	if (tx)
+		cnt = cur_rp >= rp ? cur_rp - rp : len - (rp - cur_rp);
+	else
+		cnt = cur_rp >= wp ? cur_rp - wp : len - (wp - cur_rp);
+
+	bd_ring->rp = cur_rp;
+
+	return cnt;
+}
+
+static u32 rtw89_pci_txbd_recalc(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 addr_idx = bd_ring->addr_idx;
+	u32 cnt, idx;
+
+	idx = rtw89_read32(rtwdev, addr_idx);
+	cnt = rtw89_pci_dma_recalc(rtwdev, bd_ring, idx, true);
+
+	return cnt;
+}
+
+static void rtw89_pci_release_fwcmd(struct rtw89_dev *rtwdev,
+				    struct rtw89_pci *rtwpci,
+				    u32 cnt, bool release_all)
+{
+	struct rtw89_pci_tx_data *tx_data;
+	struct sk_buff *skb;
+	u32 qlen;
+
+	while (cnt--) {
+		skb = skb_dequeue(&rtwpci->h2c_queue);
+		if (!skb) {
+			rtw89_err(rtwdev, "failed to pre-release fwcmd\n");
+			return;
+		}
+		skb_queue_tail(&rtwpci->h2c_release_queue, skb);
+	}
+
+	qlen = skb_queue_len(&rtwpci->h2c_release_queue);
+	if (!release_all)
+	       qlen = qlen > RTW89_PCI_MULTITAG ? qlen - RTW89_PCI_MULTITAG : 0;
+
+	while (qlen--) {
+		skb = skb_dequeue(&rtwpci->h2c_release_queue);
+		if (!skb) {
+			rtw89_err(rtwdev, "failed to release fwcmd\n");
+			return;
+		}
+		tx_data = RTW89_PCI_TX_SKB_CB(skb);
+		dma_unmap_single(&rtwpci->pdev->dev, tx_data->dma, skb->len,
+				 DMA_TO_DEVICE);
+		dev_kfree_skb_any(skb);
+	}
+}
+
+static void rtw89_pci_reclaim_tx_fwcmd(struct rtw89_dev *rtwdev,
+				       struct rtw89_pci *rtwpci)
+{
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[RTW89_TXCH_CH12];
+	u32 cnt;
+
+	cnt = rtw89_pci_txbd_recalc(rtwdev, tx_ring);
+	if (!cnt)
+		return;
+	rtw89_pci_release_fwcmd(rtwdev, rtwpci, cnt, false);
+}
+
+static u32 rtw89_pci_rxbd_recalc(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_rx_ring *rx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u32 addr_idx = bd_ring->addr_idx;
+	u32 cnt, idx;
+
+	idx = rtw89_read32(rtwdev, addr_idx);
+	cnt = rtw89_pci_dma_recalc(rtwdev, bd_ring, idx, false);
+
+	return cnt;
+}
+
+static void rtw89_pci_sync_skb_for_cpu(struct rtw89_dev *rtwdev,
+				       struct sk_buff *skb)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	dma_addr_t dma;
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	dma = rx_info->dma;
+	dma_sync_single_for_cpu(rtwdev->dev, dma, RTW89_PCI_RX_BUF_SIZE,
+				DMA_FROM_DEVICE);
+}
+
+static void rtw89_pci_sync_skb_for_device(struct rtw89_dev *rtwdev,
+					  struct sk_buff *skb)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	dma_addr_t dma;
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	dma = rx_info->dma;
+	dma_sync_single_for_device(rtwdev->dev, dma, RTW89_PCI_RX_BUF_SIZE,
+				   DMA_FROM_DEVICE);
+}
+
+static int rtw89_pci_rxbd_info_update(struct rtw89_dev *rtwdev,
+				      struct sk_buff *skb)
+{
+	struct rtw89_pci_rxbd_info *rxbd_info;
+	struct rtw89_pci_rx_info *rx_info = RTW89_PCI_RX_SKB_CB(skb);
+
+	rxbd_info = (struct rtw89_pci_rxbd_info *)skb->data;
+	rx_info->fs = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_FS);
+	rx_info->ls = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_LS);
+	rx_info->len = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_WRITE_SIZE);
+	rx_info->tag = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_TAG);
+
+	return 0;
+}
+
+static bool
+rtw89_skb_put_rx_data(struct rtw89_dev *rtwdev, bool fs, bool ls,
+		      struct sk_buff *new,
+		      const struct sk_buff *skb, u32 offset,
+		      const struct rtw89_pci_rx_info *rx_info,
+		      const struct rtw89_rx_desc_info *desc_info)
+{
+	u32 copy_len = rx_info->len - offset;
+
+	if (unlikely(skb_tailroom(new) < copy_len)) {
+		rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+			    "invalid rx data length bd_len=%d desc_len=%d offset=%d (fs=%d ls=%d)\n",
+			    rx_info->len, desc_info->pkt_size, offset, fs, ls);
+		rtw89_hex_dump(rtwdev, RTW89_DBG_TXRX, "rx_data: ",
+			       skb->data, rx_info->len);
+		/* length of a single segment skb is desc_info->pkt_size */
+		if (fs && ls) {
+			copy_len = desc_info->pkt_size;
+		} else {
+			rtw89_info(rtwdev, "drop rx data due to invalid length\n");
+			return false;
+		}
+	}
+
+	skb_put_data(new, skb->data + offset, copy_len);
+
+	return true;
+}
+
+static u32 rtw89_pci_rxbd_deliver_skbs(struct rtw89_dev *rtwdev,
+				       struct rtw89_pci_rx_ring *rx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	struct rtw89_pci_rx_info *rx_info;
+	struct rtw89_rx_desc_info *desc_info = &rx_ring->diliver_desc;
+	struct sk_buff *new = rx_ring->diliver_skb;
+	struct sk_buff *skb;
+	u32 rxinfo_size = sizeof(struct rtw89_pci_rxbd_info);
+	u32 offset;
+	u32 cnt = 1;
+	bool fs, ls;
+	int ret;
+
+	skb = rx_ring->buf[bd_ring->wp];
+	rtw89_pci_sync_skb_for_cpu(rtwdev, skb);
+
+	ret = rtw89_pci_rxbd_info_update(rtwdev, skb);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to update %d RXBD info: %d\n",
+			  bd_ring->wp, ret);
+		goto err_sync_device;
+	}
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	fs = rx_info->fs;
+	ls = rx_info->ls;
+
+	if (fs) {
+		if (new) {
+			rtw89_err(rtwdev, "skb should not be ready before first segment start\n");
+			goto err_sync_device;
+		}
+		if (desc_info->ready) {
+			rtw89_warn(rtwdev, "desc info should not be ready before first segment start\n");
+			goto err_sync_device;
+		}
+
+		rtw89_core_query_rxdesc(rtwdev, desc_info, skb->data, rxinfo_size);
+
+		new = dev_alloc_skb(desc_info->pkt_size);
+		if (!new)
+			goto err_sync_device;
+
+		rx_ring->diliver_skb = new;
+
+		/* first segment has RX desc */
+		offset = desc_info->offset;
+		offset += desc_info->long_rxdesc ? sizeof(struct rtw89_rxdesc_long) :
+			  sizeof(struct rtw89_rxdesc_short);
+	} else {
+		offset = sizeof(struct rtw89_pci_rxbd_info);
+		if (!new) {
+			rtw89_warn(rtwdev, "no last skb\n");
+			goto err_sync_device;
+		}
+	}
+	if (!rtw89_skb_put_rx_data(rtwdev, fs, ls, new, skb, offset, rx_info, desc_info))
+		goto err_sync_device;
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	rtw89_pci_rxbd_increase(rx_ring, 1);
+
+	if (!desc_info->ready) {
+		rtw89_warn(rtwdev, "no rx desc information\n");
+		goto err_free_resource;
+	}
+	if (ls) {
+		rtw89_core_rx(rtwdev, desc_info, new);
+		rx_ring->diliver_skb = NULL;
+		desc_info->ready = false;
+	}
+
+	return cnt;
+
+err_sync_device:
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	rtw89_pci_rxbd_increase(rx_ring, 1);
+err_free_resource:
+	if (new)
+		dev_kfree_skb_any(new);
+	rx_ring->diliver_skb = NULL;
+	desc_info->ready = false;
+
+	return cnt;
+}
+
+static void rtw89_pci_rxbd_deliver(struct rtw89_dev *rtwdev,
+				   struct rtw89_pci_rx_ring *rx_ring,
+				   u32 cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u32 rx_cnt;
+
+	while (cnt && rtwdev->napi_budget_countdown > 0) {
+		rx_cnt = rtw89_pci_rxbd_deliver_skbs(rtwdev, rx_ring);
+		if (!rx_cnt) {
+			rtw89_err(rtwdev, "failed to deliver RXBD skb\n");
+
+			/* skip the rest RXBD bufs */
+			rtw89_pci_rxbd_increase(rx_ring, cnt);
+			break;
+		}
+
+		cnt -= rx_cnt;
+	}
+
+	rtw89_write16(rtwdev, bd_ring->addr_idx, bd_ring->wp);
+}
+
+static int rtw89_pci_poll_rxq_dma(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci, int budget)
+{
+	struct rtw89_pci_rx_ring *rx_ring;
+	int countdown = rtwdev->napi_budget_countdown;
+	u32 cnt;
+
+	rx_ring = &rtwpci->rx_rings[RTW89_RXCH_RXQ];
+
+	cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
+	if (!cnt)
+		return 0;
+
+	cnt = min_t(u32, budget, cnt);
+
+	rtw89_pci_rxbd_deliver(rtwdev, rx_ring, cnt);
+
+	/* In case of flushing pending SKBs, the countdown may exceed. */
+	if (rtwdev->napi_budget_countdown <= 0)
+		return budget;
+
+	return budget - countdown;
+}
+
+static void rtw89_pci_tx_status(struct rtw89_dev *rtwdev,
+				struct rtw89_pci_tx_ring *tx_ring,
+				struct sk_buff *skb, u8 tx_status)
+{
+	struct ieee80211_tx_info *info;
+
+	info = IEEE80211_SKB_CB(skb);
+	ieee80211_tx_info_clear_status(info);
+
+	if (info->flags & IEEE80211_TX_CTL_NO_ACK)
+		info->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
+	if (tx_status == RTW89_TX_DONE) {
+		info->flags |= IEEE80211_TX_STAT_ACK;
+		tx_ring->tx_acked++;
+	} else {
+		if (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)
+			rtw89_debug(rtwdev, RTW89_DBG_FW,
+				    "failed to TX of status %x\n", tx_status);
+		switch (tx_status) {
+		case RTW89_TX_RETRY_LIMIT:
+			tx_ring->tx_retry_lmt++;
+			break;
+		case RTW89_TX_LIFE_TIME:
+			tx_ring->tx_life_time++;
+			break;
+		case RTW89_TX_MACID_DROP:
+			tx_ring->tx_mac_id_drop++;
+			break;
+		default:
+			rtw89_warn(rtwdev, "invalid TX status %x\n", tx_status);
+			break;
+		}
+	}
+
+	ieee80211_tx_status_ni(rtwdev->hw, skb);
+}
+
+static void rtw89_pci_reclaim_txbd(struct rtw89_dev *rtwdev, struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd *txwd;
+	u32 cnt;
+
+	cnt = rtw89_pci_txbd_recalc(rtwdev, tx_ring);
+	while (cnt--) {
+		txwd = list_first_entry_or_null(&tx_ring->busy_pages, struct rtw89_pci_tx_wd, list);
+		if (!txwd) {
+			rtw89_warn(rtwdev, "No busy txwd pages available\n");
+			break;
+		}
+
+		list_del_init(&txwd->list);
+	}
+}
+
+static void rtw89_pci_release_busy_txwd(struct rtw89_dev *rtwdev,
+					struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	int i;
+
+	for (i = 0; i < wd_ring->page_num; i++) {
+		txwd = list_first_entry_or_null(&tx_ring->busy_pages, struct rtw89_pci_tx_wd, list);
+		if (!txwd)
+			break;
+
+		list_del_init(&txwd->list);
+	}
+}
+
+static void rtw89_pci_release_txwd_skb(struct rtw89_dev *rtwdev,
+				       struct rtw89_pci_tx_ring *tx_ring,
+				       struct rtw89_pci_tx_wd *txwd, u16 seq,
+				       u8 tx_status)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_data *tx_data;
+	struct sk_buff *skb, *tmp;
+	u8 txch = tx_ring->txch;
+
+	if (!list_empty(&txwd->list)) {
+		rtw89_warn(rtwdev, "queue %d txwd %d is not idle\n",
+			   txch, seq);
+		return;
+	}
+
+	/* currently, support for only one frame */
+	if (skb_queue_len(&txwd->queue) != 1) {
+		rtw89_warn(rtwdev, "empty pending queue %d page %d\n",
+			   txch, seq);
+		return;
+	}
+
+	skb_queue_walk_safe(&txwd->queue, skb, tmp) {
+		skb_unlink(skb, &txwd->queue);
+
+		tx_data = RTW89_PCI_TX_SKB_CB(skb);
+		dma_unmap_single(&rtwpci->pdev->dev, tx_data->dma, skb->len,
+				 DMA_TO_DEVICE);
+
+		rtw89_pci_tx_status(rtwdev, tx_ring, skb, tx_status);
+	}
+
+	rtw89_pci_enqueue_txwd(tx_ring, txwd);
+}
+
+static void rtw89_pci_release_rpp(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci_rpp_fmt *rpp)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	struct rtw89_pci_tx_wd_ring *wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	u16 seq;
+	u8 qsel, tx_status, txch;
+
+	seq = le32_get_bits(rpp->dword, RTW89_PCI_RPP_SEQ);
+	qsel = le32_get_bits(rpp->dword, RTW89_PCI_RPP_QSEL);
+	tx_status = le32_get_bits(rpp->dword, RTW89_PCI_RPP_TX_STATUS);
+	txch = rtw89_core_get_ch_dma(rtwdev, qsel);
+
+	if (txch == RTW89_TXCH_CH12) {
+		rtw89_warn(rtwdev, "should no fwcmd release report\n");
+		return;
+	}
+
+	tx_ring = &rtwpci->tx_rings[txch];
+	rtw89_pci_reclaim_txbd(rtwdev, tx_ring);
+	wd_ring = &tx_ring->wd_ring;
+	txwd = &wd_ring->pages[seq];
+
+	rtw89_pci_release_txwd_skb(rtwdev, tx_ring, txwd, seq, tx_status);
+}
+
+static void rtw89_pci_release_pending_txwd_skb(struct rtw89_dev *rtwdev,
+					       struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	int i;
+
+	for (i = 0; i < wd_ring->page_num; i++) {
+		txwd = &wd_ring->pages[i];
+
+		if (!list_empty(&txwd->list))
+			continue;
+
+		rtw89_pci_release_txwd_skb(rtwdev, tx_ring, txwd, i, RTW89_TX_MACID_DROP);
+	}
+}
+
+static u32 rtw89_pci_release_tx_skbs(struct rtw89_dev *rtwdev,
+				     struct rtw89_pci_rx_ring *rx_ring,
+				     u32 max_cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	struct rtw89_pci_rx_info *rx_info;
+	struct rtw89_pci_rpp_fmt *rpp;
+	struct rtw89_rx_desc_info desc_info = {};
+	struct sk_buff *skb;
+	u32 cnt = 0;
+	u32 rpp_size = sizeof(struct rtw89_pci_rpp_fmt);
+	u32 rxinfo_size = sizeof(struct rtw89_pci_rxbd_info);
+	u32 offset;
+	int ret;
+
+	skb = rx_ring->buf[bd_ring->wp];
+	rtw89_pci_sync_skb_for_cpu(rtwdev, skb);
+
+	ret = rtw89_pci_rxbd_info_update(rtwdev, skb);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to update %d RXBD info: %d\n",
+			  bd_ring->wp, ret);
+		goto err_sync_device;
+	}
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	if (!rx_info->fs || !rx_info->ls) {
+		rtw89_err(rtwdev, "cannot process RP frame not set FS/LS\n");
+		return cnt;
+	}
+
+	rtw89_core_query_rxdesc(rtwdev, &desc_info, skb->data, rxinfo_size);
+
+	/* first segment has RX desc */
+	offset = desc_info.offset;
+	offset += desc_info.long_rxdesc ? sizeof(struct rtw89_rxdesc_long) :
+					  sizeof(struct rtw89_rxdesc_short);
+	for (; offset + rpp_size <= rx_info->len; offset += rpp_size) {
+		rpp = (struct rtw89_pci_rpp_fmt *)(skb->data + offset);
+		rtw89_pci_release_rpp(rtwdev, rpp);
+	}
+
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	rtw89_pci_rxbd_increase(rx_ring, 1);
+	cnt++;
+
+	return cnt;
+
+err_sync_device:
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	return 0;
+}
+
+static void rtw89_pci_release_tx(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_rx_ring *rx_ring,
+				 u32 cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u32 release_cnt;
+
+	while (cnt) {
+		release_cnt = rtw89_pci_release_tx_skbs(rtwdev, rx_ring, cnt);
+		if (!release_cnt) {
+			rtw89_err(rtwdev, "failed to release TX skbs\n");
+
+			/* skip the rest RXBD bufs */
+			rtw89_pci_rxbd_increase(rx_ring, cnt);
+			break;
+		}
+
+		cnt -= release_cnt;
+	}
+
+	rtw89_write16(rtwdev, bd_ring->addr_idx, bd_ring->wp);
+}
+
+static int rtw89_pci_poll_rpq_dma(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci, int budget)
+{
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 cnt;
+	int work_done;
+
+	rx_ring = &rtwpci->rx_rings[RTW89_RXCH_RPQ];
+
+	spin_lock_bh(&rtwpci->trx_lock);
+
+	cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
+	if (cnt == 0)
+		goto out_unlock;
+
+	rtw89_pci_release_tx(rtwdev, rx_ring, cnt);
+
+out_unlock:
+	spin_unlock_bh(&rtwpci->trx_lock);
+
+	/* always release all RPQ */
+	work_done = min_t(int, cnt, budget);
+	rtwdev->napi_budget_countdown -= work_done;
+
+	return work_done;
+}
+
+static void rtw89_pci_isr_rxd_unavail(struct rtw89_dev *rtwdev,
+				      struct rtw89_pci *rtwpci)
+{
+	struct rtw89_pci_rx_ring *rx_ring;
+	struct rtw89_pci_dma_ring *bd_ring;
+	u32 reg_idx;
+	u16 hw_idx, hw_idx_next, host_idx;
+	int i;
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		bd_ring = &rx_ring->bd_ring;
+
+		reg_idx = rtw89_read32(rtwdev, bd_ring->addr_idx);
+		hw_idx = FIELD_GET(TXBD_HW_IDX_MASK, reg_idx);
+		host_idx = FIELD_GET(TXBD_HOST_IDX_MASK, reg_idx);
+		hw_idx_next = (hw_idx + 1) % bd_ring->len;
+
+		if (hw_idx_next == host_idx)
+			rtw89_warn(rtwdev, "%d RXD unavailable\n", i);
+
+		rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+			    "%d RXD unavailable, idx=0x%08x, len=%d\n",
+			    i, reg_idx, bd_ring->len);
+	}
+}
+
+static void rtw89_pci_recognize_intrs(struct rtw89_dev *rtwdev,
+				      struct rtw89_pci *rtwpci,
+				      struct rtw89_pci_isrs *isrs)
+{
+	isrs->halt_c2h_isrs = rtw89_read32(rtwdev, R_AX_HISR0) & rtwpci->halt_c2h_intrs;
+	isrs->isrs[0] = rtw89_read32(rtwdev, R_AX_PCIE_HISR00) & rtwpci->intrs[0];
+	isrs->isrs[1] = rtw89_read32(rtwdev, R_AX_PCIE_HISR10) & rtwpci->intrs[1];
+
+	rtw89_write32(rtwdev, R_AX_HISR0, isrs->halt_c2h_isrs);
+	rtw89_write32(rtwdev, R_AX_PCIE_HISR00, isrs->isrs[0]);
+	rtw89_write32(rtwdev, R_AX_PCIE_HISR10, isrs->isrs[1]);
+}
+
+static void rtw89_pci_clear_isr0(struct rtw89_dev *rtwdev, u32 isr00)
+{
+	/* write 1 clear */
+	rtw89_write32(rtwdev, R_AX_PCIE_HISR00, isr00);
+}
+
+static void rtw89_pci_enable_intr(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci)
+{
+	rtw89_write32(rtwdev, R_AX_HIMR0, rtwpci->halt_c2h_intrs);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, rtwpci->intrs[0]);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, rtwpci->intrs[1]);
+}
+
+static void rtw89_pci_disable_intr(struct rtw89_dev *rtwdev,
+				   struct rtw89_pci *rtwpci)
+{
+	rtw89_write32(rtwdev, R_AX_HIMR0, 0);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, 0);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, 0);
+}
+
+static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)
+{
+	struct rtw89_dev *rtwdev = dev;
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_isrs isrs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtw89_pci_recognize_intrs(rtwdev, rtwpci, &isrs);
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	if (unlikely(isrs.isrs[0] & B_AX_RDU_INT))
+		rtw89_pci_isr_rxd_unavail(rtwdev, rtwpci);
+
+	if (unlikely(isrs.halt_c2h_isrs & B_AX_HALT_C2H_INT_EN))
+		rtw89_ser_notify(rtwdev, rtw89_mac_get_err_status(rtwdev));
+
+	if (likely(rtwpci->running)) {
+		local_bh_disable();
+		napi_schedule(&rtwdev->napi);
+		local_bh_enable();
+	}
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t rtw89_pci_interrupt_handler(int irq, void *dev)
+{
+	struct rtw89_dev *rtwdev = dev;
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long flags;
+	irqreturn_t irqret = IRQ_WAKE_THREAD;
+
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+
+	/* If interrupt event is on the road, it is still trigger interrupt
+	 * even we have done pci_stop() to turn off IMR.
+	 */
+	if (unlikely(!rtwpci->running)) {
+		irqret = IRQ_HANDLED;
+		goto exit;
+	}
+
+	rtw89_pci_disable_intr(rtwdev, rtwpci);
+exit:
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	return irqret;
+}
+
+#define case_TXCHADDRS(txch) \
+	case RTW89_TXCH_##txch: \
+		*addr_num = R_AX_##txch##_TXBD_NUM; \
+		*addr_idx = R_AX_##txch##_TXBD_IDX; \
+		*addr_bdram = R_AX_##txch##_BDRAM_CTRL; \
+		*addr_desa_l = R_AX_##txch##_TXBD_DESA_L; \
+		*addr_desa_h = R_AX_##txch##_TXBD_DESA_H; \
+		break
+
+static int rtw89_pci_get_txch_addrs(enum rtw89_tx_channel txch,
+				    u32 *addr_num,
+				    u32 *addr_idx,
+				    u32 *addr_bdram,
+				    u32 *addr_desa_l,
+				    u32 *addr_desa_h)
+{
+	switch (txch) {
+	case_TXCHADDRS(ACH0);
+	case_TXCHADDRS(ACH1);
+	case_TXCHADDRS(ACH2);
+	case_TXCHADDRS(ACH3);
+	case_TXCHADDRS(ACH4);
+	case_TXCHADDRS(ACH5);
+	case_TXCHADDRS(ACH6);
+	case_TXCHADDRS(ACH7);
+	case_TXCHADDRS(CH8);
+	case_TXCHADDRS(CH9);
+	case_TXCHADDRS(CH10);
+	case_TXCHADDRS(CH11);
+	case_TXCHADDRS(CH12);
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+#undef case_TXCHADDRS
+
+#define case_RXCHADDRS(rxch) \
+	case RTW89_RXCH_##rxch: \
+		*addr_num = R_AX_##rxch##_RXBD_NUM; \
+		*addr_idx = R_AX_##rxch##_RXBD_IDX; \
+		*addr_desa_l = R_AX_##rxch##_RXBD_DESA_L; \
+		*addr_desa_h = R_AX_##rxch##_RXBD_DESA_H; \
+		break
+
+static int rtw89_pci_get_rxch_addrs(enum rtw89_rx_channel rxch,
+				    u32 *addr_num,
+				    u32 *addr_idx,
+				    u32 *addr_desa_l,
+				    u32 *addr_desa_h)
+{
+	switch (rxch) {
+	case_RXCHADDRS(RXQ);
+	case_RXCHADDRS(RPQ);
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+#undef case_RXCHADDRS
+
+static u32 rtw89_pci_get_avail_txbd_num(struct rtw89_pci_tx_ring *ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &ring->bd_ring;
+
+	/* reserved 1 desc check ring is full or not */
+	if (bd_ring->rp > bd_ring->wp)
+		return bd_ring->rp - bd_ring->wp - 1;
+
+	return bd_ring->len - (bd_ring->wp - bd_ring->rp) - 1;
+}
+
+static
+u32 __rtw89_pci_check_and_reclaim_tx_fwcmd_resource(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[RTW89_TXCH_CH12];
+	u32 cnt;
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	rtw89_pci_reclaim_tx_fwcmd(rtwdev, rtwpci);
+	cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
+	spin_unlock_bh(&rtwpci->trx_lock);
+
+	return cnt;
+}
+
+static u32 __rtw89_pci_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev,
+						     u8 txch)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	u32 bd_cnt, wd_cnt, min_cnt = 0;
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 cnt;
+
+	rx_ring = &rtwpci->rx_rings[RTW89_RXCH_RPQ];
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	bd_cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
+	wd_cnt = wd_ring->curr_num;
+
+	if (wd_cnt == 0 || bd_cnt == 0) {
+		cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
+		if (!cnt)
+			goto out_unlock;
+		rtw89_pci_release_tx(rtwdev, rx_ring, cnt);
+	}
+
+	bd_cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
+	wd_cnt = wd_ring->curr_num;
+	min_cnt = min(bd_cnt, wd_cnt);
+	if (min_cnt == 0)
+		rtw89_warn(rtwdev, "still no tx resource after reclaim\n");
+
+out_unlock:
+	spin_unlock_bh(&rtwpci->trx_lock);
+
+	return min_cnt;
+}
+
+static u32 rtw89_pci_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev,
+						   u8 txch)
+{
+	if (txch == RTW89_TXCH_CH12)
+		return __rtw89_pci_check_and_reclaim_tx_fwcmd_resource(rtwdev);
+
+	return __rtw89_pci_check_and_reclaim_tx_resource(rtwdev, txch);
+}
+
+static void __rtw89_pci_tx_kick_off(struct rtw89_dev *rtwdev, struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 host_idx, addr;
+
+	addr = bd_ring->addr_idx;
+	host_idx = bd_ring->wp;
+	rtw89_write16(rtwdev, addr, host_idx);
+}
+
+static void rtw89_pci_tx_bd_ring_update(struct rtw89_dev *rtwdev, struct rtw89_pci_tx_ring *tx_ring,
+					int n_txbd)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 host_idx, len;
+
+	len = bd_ring->len;
+	host_idx = bd_ring->wp + n_txbd;
+	host_idx = host_idx < len ? host_idx : host_idx - len;
+
+	bd_ring->wp = host_idx;
+}
+
+static void rtw89_pci_ops_tx_kick_off(struct rtw89_dev *rtwdev, u8 txch)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	__rtw89_pci_tx_kick_off(rtwdev, tx_ring);
+	spin_unlock_bh(&rtwpci->trx_lock);
+}
+
+static void __pci_flush_txch(struct rtw89_dev *rtwdev, u8 txch, bool drop)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 cur_idx, cur_rp;
+	u8 i;
+
+	/* Because the time taked by the I/O is a bit dynamic, it's hard to
+	 * define a reasonable fixed total timeout to use read_poll_timeout*
+	 * helper. Instead, we can ensure a reasonable polling times, so we
+	 * just use for loop with udelay here.
+	 */
+	for (i = 0; i < 60; i++) {
+		cur_idx = rtw89_read32(rtwdev, bd_ring->addr_idx);
+		cur_rp = FIELD_GET(TXBD_HW_IDX_MASK, cur_idx);
+		if (cur_rp == bd_ring->wp)
+			return;
+
+		udelay(1);
+	}
+
+	if (!drop)
+		rtw89_info(rtwdev, "timed out to flush pci txch: %d\n", txch);
+}
+
+static void __rtw89_pci_ops_flush_txchs(struct rtw89_dev *rtwdev, u32 txchs,
+					bool drop)
+{
+	u8 i;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		/* It may be unnecessary to flush FWCMD queue. */
+		if (i == RTW89_TXCH_CH12)
+			continue;
+
+		if (txchs & BIT(i))
+			__pci_flush_txch(rtwdev, i, drop);
+	}
+}
+
+static void rtw89_pci_ops_flush_queues(struct rtw89_dev *rtwdev, u32 queues,
+				       bool drop)
+{
+	__rtw89_pci_ops_flush_txchs(rtwdev, BIT(RTW89_TXCH_NUM) - 1, drop);
+}
+
+static int rtw89_pci_txwd_submit(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_tx_ring *tx_ring,
+				 struct rtw89_pci_tx_wd *txwd,
+				 struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct rtw89_txwd_body *txwd_body;
+	struct rtw89_txwd_info *txwd_info;
+	struct rtw89_pci_tx_wp_info *txwp_info;
+	struct rtw89_pci_tx_addr_info_32 *txaddr_info;
+	struct pci_dev *pdev = rtwpci->pdev;
+	struct sk_buff *skb = tx_req->skb;
+	struct rtw89_pci_tx_data *tx_data = RTW89_PCI_TX_SKB_CB(skb);
+	bool en_wd_info = desc_info->en_wd_info;
+	u32 txwd_len;
+	u32 txwp_len;
+	u32 txaddr_info_len;
+	dma_addr_t dma;
+	int ret;
+
+	rtw89_core_fill_txdesc(rtwdev, desc_info, txwd->vaddr);
+
+	dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(&pdev->dev, dma)) {
+		rtw89_err(rtwdev, "failed to map skb dma data\n");
+		ret = -EBUSY;
+		goto err;
+	}
+
+	tx_data->dma = dma;
+
+	txaddr_info_len = sizeof(*txaddr_info);
+	txwp_len = sizeof(*txwp_info);
+	txwd_len = sizeof(*txwd_body);
+	txwd_len += en_wd_info ? sizeof(*txwd_info) : 0;
+
+	txwp_info = txwd->vaddr + txwd_len;
+	txwp_info->seq0 = cpu_to_le16(txwd->seq | RTW89_PCI_TXWP_VALID);
+	txwp_info->seq1 = 0;
+	txwp_info->seq2 = 0;
+	txwp_info->seq3 = 0;
+
+	tx_ring->tx_cnt++;
+	txaddr_info = txwd->vaddr + txwd_len + txwp_len;
+	txaddr_info->length = cpu_to_le16(skb->len);
+	txaddr_info->option = cpu_to_le16(RTW89_PCI_ADDR_MSDU_LS |
+					  RTW89_PCI_ADDR_NUM(1));
+	txaddr_info->dma = cpu_to_le32(dma);
+
+	txwd->len = txwd_len + txwp_len + txaddr_info_len;
+
+	skb_queue_tail(&txwd->queue, skb);
+
+	return 0;
+
+err:
+	return ret;
+}
+
+static int rtw89_pci_fwcmd_submit(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci_tx_ring *tx_ring,
+				  struct rtw89_pci_tx_bd_32 *txbd,
+				  struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct rtw89_txwd_body *txwd_body;
+	struct pci_dev *pdev = rtwpci->pdev;
+	struct sk_buff *skb = tx_req->skb;
+	struct rtw89_pci_tx_data *tx_data = RTW89_PCI_TX_SKB_CB(skb);
+	dma_addr_t dma;
+
+	txwd_body = (struct rtw89_txwd_body *)skb_push(skb, sizeof(*txwd_body));
+	memset(txwd_body, 0, sizeof(*txwd_body));
+	rtw89_core_fill_txdesc(rtwdev, desc_info, txwd_body);
+
+	dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(&pdev->dev, dma)) {
+		rtw89_err(rtwdev, "failed to map fwcmd dma data\n");
+		return -EBUSY;
+	}
+
+	tx_data->dma = dma;
+	txbd->option = cpu_to_le16(RTW89_PCI_TXBD_OPTION_LS);
+	txbd->length = cpu_to_le16(skb->len);
+	txbd->dma = cpu_to_le32(tx_data->dma);
+	skb_queue_tail(&rtwpci->h2c_queue, skb);
+
+	rtw89_pci_tx_bd_ring_update(rtwdev, tx_ring, 1);
+
+	return 0;
+}
+
+static int rtw89_pci_txbd_submit(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_tx_ring *tx_ring,
+				 struct rtw89_pci_tx_bd_32 *txbd,
+				 struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_pci_tx_wd *txwd;
+	int ret;
+
+	/* FWCMD queue doesn't have wd pages. Instead, it submits the CMD
+	 * buffer with WD BODY only. So here we don't need to check the free
+	 * pages of the wd ring.
+	 */
+	if (tx_ring->txch == RTW89_TXCH_CH12)
+		return rtw89_pci_fwcmd_submit(rtwdev, tx_ring, txbd, tx_req);
+
+	txwd = rtw89_pci_dequeue_txwd(tx_ring);
+	if (!txwd) {
+		rtw89_err(rtwdev, "no available TXWD\n");
+		ret = -ENOSPC;
+		goto err;
+	}
+
+	ret = rtw89_pci_txwd_submit(rtwdev, tx_ring, txwd, tx_req);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to submit TXWD %d\n", txwd->seq);
+		goto err_enqueue_wd;
+	}
+
+	list_add_tail(&txwd->list, &tx_ring->busy_pages);
+
+	txbd->option = cpu_to_le16(RTW89_PCI_TXBD_OPTION_LS);
+	txbd->length = cpu_to_le16(txwd->len);
+	txbd->dma = cpu_to_le32(txwd->paddr);
+
+	rtw89_pci_tx_bd_ring_update(rtwdev, tx_ring, 1);
+
+	return 0;
+
+err_enqueue_wd:
+	rtw89_pci_enqueue_txwd(tx_ring, txwd);
+err:
+	return ret;
+}
+
+static int rtw89_pci_tx_write(struct rtw89_dev *rtwdev, struct rtw89_core_tx_request *tx_req,
+			      u8 txch)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	struct rtw89_pci_tx_bd_32 *txbd;
+	u32 n_avail_txbd;
+	int ret = 0;
+
+	/* check the tx type and dma channel for fw cmd queue */
+	if ((txch == RTW89_TXCH_CH12 ||
+	     tx_req->tx_type == RTW89_CORE_TX_TYPE_FWCMD) &&
+	    (txch != RTW89_TXCH_CH12 ||
+	     tx_req->tx_type != RTW89_CORE_TX_TYPE_FWCMD)) {
+		rtw89_err(rtwdev, "only fw cmd uses dma channel 12\n");
+		return -EINVAL;
+	}
+
+	tx_ring = &rtwpci->tx_rings[txch];
+	spin_lock_bh(&rtwpci->trx_lock);
+
+	n_avail_txbd = rtw89_pci_get_avail_txbd_num(tx_ring);
+	if (n_avail_txbd == 0) {
+		rtw89_err(rtwdev, "no available TXBD\n");
+		ret = -ENOSPC;
+		goto err_unlock;
+	}
+
+	txbd = rtw89_pci_get_next_txbd(tx_ring);
+	ret = rtw89_pci_txbd_submit(rtwdev, tx_ring, txbd, tx_req);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to submit TXBD\n");
+		goto err_unlock;
+	}
+
+	spin_unlock_bh(&rtwpci->trx_lock);
+	return 0;
+
+err_unlock:
+	spin_unlock_bh(&rtwpci->trx_lock);
+	return ret;
+}
+
+static int rtw89_pci_ops_tx_write(struct rtw89_dev *rtwdev, struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	int ret;
+
+	ret = rtw89_pci_tx_write(rtwdev, tx_req, desc_info->ch_dma);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to TX Queue %d\n", desc_info->ch_dma);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct rtw89_pci_bd_ram bd_ram_table[RTW89_TXCH_NUM] = {
+	[RTW89_TXCH_ACH0] = {.start_idx = 0,  .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH1] = {.start_idx = 5,  .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH2] = {.start_idx = 10, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH3] = {.start_idx = 15, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH4] = {.start_idx = 20, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH5] = {.start_idx = 25, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH6] = {.start_idx = 30, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH7] = {.start_idx = 35, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_CH8]  = {.start_idx = 40, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH9]  = {.start_idx = 45, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH10] = {.start_idx = 50, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH11] = {.start_idx = 55, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH12] = {.start_idx = 60, .max_num = 4, .min_num = 1},
+};
+
+static void rtw89_pci_reset_trx_rings(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	struct rtw89_pci_rx_ring *rx_ring;
+	struct rtw89_pci_dma_ring *bd_ring;
+	const struct rtw89_pci_bd_ram *bd_ram;
+	u32 addr_num;
+	u32 addr_bdram;
+	u32 addr_desa_l;
+	u32 val32;
+	int i;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		bd_ring = &tx_ring->bd_ring;
+		bd_ram = &bd_ram_table[i];
+		addr_num = bd_ring->addr_num;
+		addr_bdram = bd_ring->addr_bdram;
+		addr_desa_l = bd_ring->addr_desa_l;
+		bd_ring->wp = 0;
+		bd_ring->rp = 0;
+
+		val32 = FIELD_PREP(BDRAM_SIDX_MASK, bd_ram->start_idx) |
+			FIELD_PREP(BDRAM_MAX_MASK, bd_ram->max_num) |
+			FIELD_PREP(BDRAM_MIN_MASK, bd_ram->min_num);
+
+		rtw89_write16(rtwdev, addr_num, bd_ring->len);
+		rtw89_write32(rtwdev, addr_bdram, val32);
+		rtw89_write32(rtwdev, addr_desa_l, bd_ring->dma);
+	}
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		bd_ring = &rx_ring->bd_ring;
+		addr_num = bd_ring->addr_num;
+		addr_desa_l = bd_ring->addr_desa_l;
+		bd_ring->wp = 0;
+		bd_ring->rp = 0;
+		rx_ring->diliver_skb = NULL;
+		rx_ring->diliver_desc.ready = false;
+
+		rtw89_write16(rtwdev, addr_num, bd_ring->len);
+		rtw89_write32(rtwdev, addr_desa_l, bd_ring->dma);
+	}
+}
+
+static void rtw89_pci_release_tx_ring(struct rtw89_dev *rtwdev,
+				      struct rtw89_pci_tx_ring *tx_ring)
+{
+	rtw89_pci_release_busy_txwd(rtwdev, tx_ring);
+	rtw89_pci_release_pending_txwd_skb(rtwdev, tx_ring);
+}
+
+static void rtw89_pci_ops_reset(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	int txch;
+
+	rtw89_pci_reset_trx_rings(rtwdev);
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	for (txch = 0; txch < RTW89_TXCH_NUM; txch++) {
+		if (txch == RTW89_TXCH_CH12) {
+			rtw89_pci_release_fwcmd(rtwdev, rtwpci,
+						skb_queue_len(&rtwpci->h2c_queue), true);
+			continue;
+		}
+		rtw89_pci_release_tx_ring(rtwdev, &rtwpci->tx_rings[txch]);
+	}
+	spin_unlock_bh(&rtwpci->trx_lock);
+}
+
+static int rtw89_pci_ops_start(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long flags;
+
+	rtw89_core_napi_start(rtwdev);
+
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtwpci->running = true;
+	rtw89_pci_enable_intr(rtwdev, rtwpci);
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	return 0;
+}
+
+static void rtw89_pci_ops_stop(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct pci_dev *pdev = rtwpci->pdev;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtwpci->running = false;
+	rtw89_pci_disable_intr(rtwdev, rtwpci);
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	synchronize_irq(pdev->irq);
+	rtw89_core_napi_stop(rtwdev);
+}
+
+static void rtw89_pci_ops_write32(struct rtw89_dev *rtwdev, u32 addr, u32 data);
+
+static u32 rtw89_pci_ops_read32_cmac(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 val = readl(rtwpci->mmap + addr);
+	int count;
+
+	for (count = 0; ; count++) {
+		if (val != RTW89_R32_DEAD)
+			return val;
+		if (count >= MAC_REG_POOL_COUNT) {
+			rtw89_warn(rtwdev, "addr %#x = %#x\n", addr, val);
+			return RTW89_R32_DEAD;
+		}
+		rtw89_pci_ops_write32(rtwdev, R_AX_CK_EN, B_AX_CMAC_ALLCKEN);
+		val = readl(rtwpci->mmap + addr);
+	}
+
+	return val;
+}
+
+static u8 rtw89_pci_ops_read8(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 addr32, val32, shift;
+
+	if (!ACCESS_CMAC(addr))
+		return readb(rtwpci->mmap + addr);
+
+	addr32 = addr & ~0x3;
+	shift = (addr & 0x3) * 8;
+	val32 = rtw89_pci_ops_read32_cmac(rtwdev, addr32);
+	return val32 >> shift;
+}
+
+static u16 rtw89_pci_ops_read16(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 addr32, val32, shift;
+
+	if (!ACCESS_CMAC(addr))
+		return readw(rtwpci->mmap + addr);
+
+	addr32 = addr & ~0x3;
+	shift = (addr & 0x3) * 8;
+	val32 = rtw89_pci_ops_read32_cmac(rtwdev, addr32);
+	return val32 >> shift;
+}
+
+static u32 rtw89_pci_ops_read32(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	if (!ACCESS_CMAC(addr))
+		return readl(rtwpci->mmap + addr);
+
+	return rtw89_pci_ops_read32_cmac(rtwdev, addr);
+}
+
+static void rtw89_pci_ops_write8(struct rtw89_dev *rtwdev, u32 addr, u8 data)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	writeb(data, rtwpci->mmap + addr);
+}
+
+static void rtw89_pci_ops_write16(struct rtw89_dev *rtwdev, u32 addr, u16 data)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	writew(data, rtwpci->mmap + addr);
+}
+
+static void rtw89_pci_ops_write32(struct rtw89_dev *rtwdev, u32 addr, u32 data)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	writel(data, rtwpci->mmap + addr);
+}
+
+static void rtw89_pci_ctrl_dma_all(struct rtw89_dev *rtwdev, bool enable)
+{
+	if (enable) {
+		rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1,
+				  B_AX_TXHCI_EN | B_AX_RXHCI_EN);
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1,
+				  B_AX_STOP_PCIEIO);
+	} else {
+		rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1,
+				  B_AX_STOP_PCIEIO);
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1,
+				  B_AX_TXHCI_EN | B_AX_RXHCI_EN);
+	}
+}
+
+static int rtw89_pci_check_mdio(struct rtw89_dev *rtwdev, u8 addr, u8 speed, u16 rw_bit)
+{
+	u16 val;
+
+	rtw89_write8(rtwdev, R_AX_MDIO_CFG, addr & 0x1F);
+
+	val = rtw89_read16(rtwdev, R_AX_MDIO_CFG);
+	switch (speed) {
+	case PCIE_PHY_GEN1:
+		if (addr < 0x20)
+			val = u16_replace_bits(val, MDIO_PG0_G1, B_AX_MDIO_PHY_ADDR_MASK);
+		else
+			val = u16_replace_bits(val, MDIO_PG1_G1, B_AX_MDIO_PHY_ADDR_MASK);
+		break;
+	case PCIE_PHY_GEN2:
+		if (addr < 0x20)
+			val = u16_replace_bits(val, MDIO_PG0_G2, B_AX_MDIO_PHY_ADDR_MASK);
+		else
+			val = u16_replace_bits(val, MDIO_PG1_G2, B_AX_MDIO_PHY_ADDR_MASK);
+		break;
+	default:
+		rtw89_err(rtwdev, "[ERR]Error Speed %d!\n", speed);
+		return -EINVAL;
+	}
+	rtw89_write16(rtwdev, R_AX_MDIO_CFG, val);
+	rtw89_write16_set(rtwdev, R_AX_MDIO_CFG, rw_bit);
+
+	return read_poll_timeout(rtw89_read16, val, !(val & rw_bit), 10, 2000,
+				 false, rtwdev, R_AX_MDIO_CFG);
+}
+
+static int
+rtw89_read16_mdio(struct rtw89_dev *rtwdev, u8 addr, u8 speed, u16 *val)
+{
+	int ret;
+
+	ret = rtw89_pci_check_mdio(rtwdev, addr, speed, B_AX_MDIO_RFLAG);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]MDIO R16 0x%X fail ret=%d!\n", addr, ret);
+		return ret;
+	}
+	*val = rtw89_read16(rtwdev, R_AX_MDIO_RDATA);
+
+	return 0;
+}
+
+static int
+rtw89_write16_mdio(struct rtw89_dev *rtwdev, u8 addr, u16 data, u8 speed)
+{
+	int ret;
+
+	rtw89_write16(rtwdev, R_AX_MDIO_WDATA, data);
+	ret = rtw89_pci_check_mdio(rtwdev, addr, speed, B_AX_MDIO_WFLAG);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]MDIO W16 0x%X = %x fail ret=%d!\n", addr, data, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rtw89_write16_mdio_set(struct rtw89_dev *rtwdev, u8 addr, u16 mask, u8 speed)
+{
+	int ret;
+	u16 val;
+
+	ret = rtw89_read16_mdio(rtwdev, addr, speed, &val);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, addr, val | mask, speed);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int rtw89_write16_mdio_clr(struct rtw89_dev *rtwdev, u8 addr, u16 mask, u8 speed)
+{
+	int ret;
+	u16 val;
+
+	ret = rtw89_read16_mdio(rtwdev, addr, speed, &val);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, addr, val & ~mask, speed);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int rtw89_dbi_write8(struct rtw89_dev *rtwdev, u16 addr, u8 data)
+{
+	u16 write_addr;
+	u16 remainder = addr & ~(B_AX_DBI_ADDR_MSK | B_AX_DBI_WREN_MSK);
+	u8 flag;
+	int ret;
+
+	write_addr = addr & B_AX_DBI_ADDR_MSK;
+	write_addr |= u16_encode_bits(BIT(remainder), B_AX_DBI_WREN_MSK);
+	rtw89_write8(rtwdev, R_AX_DBI_WDATA + remainder, data);
+	rtw89_write16(rtwdev, R_AX_DBI_FLAG, write_addr);
+	rtw89_write8(rtwdev, R_AX_DBI_FLAG + 2, B_AX_DBI_WFLAG >> 16);
+
+	ret = read_poll_timeout_atomic(rtw89_read8, flag, !flag, 10,
+				       10 * RTW89_PCI_WR_RETRY_CNT, false,
+				       rtwdev, R_AX_DBI_FLAG + 2);
+	if (ret)
+		WARN(flag, "failed to write to DBI register, addr=0x%04x\n",
+		     addr);
+
+	return ret;
+}
+
+static int rtw89_dbi_read8(struct rtw89_dev *rtwdev, u16 addr, u8 *value)
+{
+	u16 read_addr = addr & B_AX_DBI_ADDR_MSK;
+	u8 flag;
+	int ret;
+
+	rtw89_write16(rtwdev, R_AX_DBI_FLAG, read_addr);
+	rtw89_write8(rtwdev, R_AX_DBI_FLAG + 2, B_AX_DBI_RFLAG >> 16);
+
+	ret = read_poll_timeout_atomic(rtw89_read8, flag, !flag, 10,
+				       10 * RTW89_PCI_WR_RETRY_CNT, false,
+				       rtwdev, R_AX_DBI_FLAG + 2);
+
+	if (!ret) {
+		read_addr = R_AX_DBI_RDATA + (addr & 3);
+		*value = rtw89_read8(rtwdev, read_addr);
+	} else {
+		WARN(1, "failed to read DBI register, addr=0x%04x\n", addr);
+		ret = -EIO;
+	}
+
+	return ret;
+}
+
+static int rtw89_dbi_write8_set(struct rtw89_dev *rtwdev, u16 addr, u8 bit)
+{
+	u8 value;
+	int ret;
+
+	ret = rtw89_dbi_read8(rtwdev, addr, &value);
+	if (ret)
+		return ret;
+
+	value |= bit;
+	ret = rtw89_dbi_write8(rtwdev, addr, value);
+
+	return ret;
+}
+
+static int rtw89_dbi_write8_clr(struct rtw89_dev *rtwdev, u16 addr, u8 bit)
+{
+	u8 value;
+	int ret;
+
+	ret = rtw89_dbi_read8(rtwdev, addr, &value);
+	if (ret)
+		return ret;
+
+	value &= ~bit;
+	ret = rtw89_dbi_write8(rtwdev, addr, value);
+
+	return ret;
+}
+
+static int
+__get_target(struct rtw89_dev *rtwdev, u16 *target, enum rtw89_pcie_phy phy_rate)
+{
+	u16 val, tar;
+	int ret;
+
+	/* Enable counter */
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val & ~B_AX_CLK_CALIB_EN,
+				 phy_rate);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val | B_AX_CLK_CALIB_EN,
+				 phy_rate);
+	if (ret)
+		return ret;
+
+	fsleep(300);
+
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &tar);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val & ~B_AX_CLK_CALIB_EN,
+				 phy_rate);
+	if (ret)
+		return ret;
+
+	tar = tar & 0x0FFF;
+	if (tar == 0 || tar == 0x0FFF) {
+		rtw89_err(rtwdev, "[ERR]Get target failed.\n");
+		return -EINVAL;
+	}
+
+	*target = tar;
+
+	return 0;
+}
+
+static int rtw89_pci_auto_refclk_cal(struct rtw89_dev *rtwdev, bool autook_en)
+{
+	enum rtw89_pcie_phy phy_rate;
+	u16 val16, mgn_set, div_set, tar;
+	u8 val8, bdr_ori;
+	bool l1_flag = false;
+	int ret = 0;
+
+	if ((rtwdev->chip->chip_id == RTL8852A && rtwdev->hal.cv == CHIP_CBV) ||
+	    rtwdev->chip->chip_id == RTL8852C)
+		return 0;
+
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_PHY_RATE, &val8);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]dbi_r8_pcie %X\n", RTW89_PCIE_PHY_RATE);
+		return ret;
+	}
+
+	if (FIELD_GET(RTW89_PCIE_PHY_RATE_MASK, val8) == 0x1) {
+		phy_rate = PCIE_PHY_GEN1;
+	} else if (FIELD_GET(RTW89_PCIE_PHY_RATE_MASK, val8) == 0x2) {
+		phy_rate = PCIE_PHY_GEN2;
+	} else {
+		rtw89_err(rtwdev, "[ERR]PCIe PHY rate %#x not support\n", val8);
+		return -EOPNOTSUPP;
+	}
+	/* Disable L1BD */
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_L1_CTRL, &bdr_ori);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]dbi_r8_pcie %X\n", RTW89_PCIE_L1_CTRL);
+		return ret;
+	}
+
+	if (bdr_ori & RTW89_PCIE_BIT_L1) {
+		ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_L1_CTRL,
+				       bdr_ori & ~RTW89_PCIE_BIT_L1);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]dbi_w8_pcie %X\n", RTW89_PCIE_L1_CTRL);
+			return ret;
+		}
+		l1_flag = true;
+	}
+
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val16);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_r16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	if (val16 & B_AX_CALIB_EN) {
+		ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1,
+					 val16 & ~B_AX_CALIB_EN, phy_rate);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+			goto end;
+		}
+	}
+
+	if (!autook_en)
+		goto end;
+	/* Set div */
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_CTRL_PPR_V1, B_AX_DIV, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	/* Obtain div and margin */
+	ret = __get_target(rtwdev, &tar, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]1st get target fail %d\n", ret);
+		goto end;
+	}
+
+	mgn_set = tar * INTF_INTGRA_HOSTREF_V1 / INTF_INTGRA_MINREF_V1 - tar;
+
+	if (mgn_set >= 128) {
+		div_set = 0x0003;
+		mgn_set = 0x000F;
+	} else if (mgn_set >= 64) {
+		div_set = 0x0003;
+		mgn_set >>= 3;
+	} else if (mgn_set >= 32) {
+		div_set = 0x0002;
+		mgn_set >>= 2;
+	} else if (mgn_set >= 16) {
+		div_set = 0x0001;
+		mgn_set >>= 1;
+	} else if (mgn_set == 0) {
+		rtw89_err(rtwdev, "[ERR]cal mgn is 0,tar = %d\n", tar);
+		goto end;
+	} else {
+		div_set = 0x0000;
+	}
+
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val16);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_r16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	val16 |= u16_encode_bits(div_set, B_AX_DIV);
+
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val16, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	ret = __get_target(rtwdev, &tar, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]2nd get target fail %d\n", ret);
+		goto end;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_HCI, "[TRACE]target = 0x%X, div = 0x%X, margin = 0x%X\n",
+		    tar, div_set, mgn_set);
+	ret = rtw89_write16_mdio(rtwdev, RAC_SET_PPR_V1,
+				 (tar & 0x0FFF) | (mgn_set << 12), phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_SET_PPR_V1);
+		goto end;
+	}
+
+	/* Enable function */
+	ret = rtw89_write16_mdio_set(rtwdev, RAC_CTRL_PPR_V1, B_AX_CALIB_EN, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	/* CLK delay = 0 */
+	ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_CLK_CTRL, PCIE_CLKDLY_HW_0);
+
+end:
+	/* Set L1BD to ori */
+	if (l1_flag) {
+		ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_L1_CTRL, bdr_ori);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]dbi_w8_pcie %X\n", RTW89_PCIE_L1_CTRL);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_deglitch_setting(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	if (rtwdev->chip->chip_id != RTL8852A)
+		return 0;
+
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA24, B_AX_DEGLITCH,
+				     PCIE_PHY_GEN1);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA24, B_AX_DEGLITCH,
+				     PCIE_PHY_GEN2);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void rtw89_pci_rxdma_prefth(struct rtw89_dev *rtwdev)
+{
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_DIS_RXDMA_PRE);
+}
+
+static void rtw89_pci_l1off_pwroff(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_PS_CTRL, B_AX_L1OFF_PWR_OFF_EN);
+}
+
+static u32 rtw89_pci_l2_rxen_lat(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return 0;
+
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA26, B_AX_RXEN,
+				     PCIE_PHY_GEN1);
+	if (ret)
+		return ret;
+
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA26, B_AX_RXEN,
+				     PCIE_PHY_GEN2);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void rtw89_pci_aphy_pwrcut(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id != RTL8852A)
+		return;
+
+	rtw89_write32_clr(rtwdev, R_AX_SYS_PW_CTRL, B_AX_PSUS_OFF_CAPC_EN);
+}
+
+static void rtw89_pci_hci_ldo(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id != RTL8852A)
+		return;
+
+	rtw89_write32_set(rtwdev, R_AX_SYS_SDIO_CTRL,
+			  B_AX_PCIE_DIS_L2_CTRL_LDO_HCI);
+	rtw89_write32_clr(rtwdev, R_AX_SYS_SDIO_CTRL,
+			  B_AX_PCIE_DIS_WLSUS_AFT_PDN);
+}
+
+static void rtw89_pci_set_sic(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_EXP_CTRL,
+			  B_AX_SIC_EN_FORCE_CLKREQ);
+}
+
+static void rtw89_pci_set_dbg(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DBG_CTRL,
+			  B_AX_ASFF_FULL_NO_STK | B_AX_EN_STUCK_DBG);
+
+	if (rtwdev->chip->chip_id == RTL8852A)
+		rtw89_write32_set(rtwdev, R_AX_PCIE_EXP_CTRL,
+				  B_AX_EN_CHKDSC_NO_RX_STUCK);
+}
+
+static void rtw89_pci_clr_idx_all(struct rtw89_dev *rtwdev)
+{
+	u32 val = B_AX_CLR_ACH0_IDX | B_AX_CLR_ACH1_IDX | B_AX_CLR_ACH2_IDX |
+		  B_AX_CLR_ACH3_IDX | B_AX_CLR_CH8_IDX | B_AX_CLR_CH9_IDX |
+		  B_AX_CLR_CH12_IDX;
+
+	if (rtwdev->chip->chip_id == RTL8852A)
+		val |= B_AX_CLR_ACH4_IDX | B_AX_CLR_ACH5_IDX |
+		       B_AX_CLR_ACH6_IDX | B_AX_CLR_ACH7_IDX;
+	/* clear DMA indexes */
+	rtw89_write32_set(rtwdev, R_AX_TXBD_RWPTR_CLR1, val);
+	if (rtwdev->chip->chip_id == RTL8852A)
+		rtw89_write32_set(rtwdev, R_AX_TXBD_RWPTR_CLR2,
+				  B_AX_CLR_CH10_IDX | B_AX_CLR_CH11_IDX);
+	rtw89_write32_set(rtwdev, R_AX_RXBD_RWPTR_CLR,
+			  B_AX_CLR_RXQ_IDX | B_AX_CLR_RPQ_IDX);
+}
+
+static int rtw89_pci_ops_deinit(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852A) {
+		/* ltr sw trigger */
+		rtw89_write32_set(rtwdev, R_AX_LTR_CTRL_0, B_AX_APP_LTR_IDLE);
+	}
+	rtw89_pci_ctrl_dma_all(rtwdev, false);
+	rtw89_pci_clr_idx_all(rtwdev);
+
+	return 0;
+}
+
+static int rtw89_pci_ops_mac_pre_init(struct rtw89_dev *rtwdev)
+{
+	u32 dma_busy;
+	u32 check;
+	u32 lbc;
+	int ret;
+
+	rtw89_pci_rxdma_prefth(rtwdev);
+	rtw89_pci_l1off_pwroff(rtwdev);
+	rtw89_pci_deglitch_setting(rtwdev);
+	ret = rtw89_pci_l2_rxen_lat(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] pcie l2 rxen lat %d\n", ret);
+		return ret;
+	}
+
+	rtw89_pci_aphy_pwrcut(rtwdev);
+	rtw89_pci_hci_ldo(rtwdev);
+
+	ret = rtw89_pci_auto_refclk_cal(rtwdev, false);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] pcie autok fail %d\n", ret);
+		return ret;
+	}
+
+	rtw89_pci_set_sic(rtwdev);
+	rtw89_pci_set_dbg(rtwdev);
+
+	if (rtwdev->chip->chip_id == RTL8852A)
+		rtw89_write32_clr(rtwdev, R_AX_SYS_SDIO_CTRL,
+				  B_AX_PCIE_AUXCLK_GATE);
+
+	lbc = rtw89_read32(rtwdev, R_AX_LBC_WATCHDOG);
+	lbc = u32_replace_bits(lbc, RTW89_MAC_LBC_TMR_128US, B_AX_LBC_TIMER);
+	lbc |= B_AX_LBC_FLAG | B_AX_LBC_EN;
+	rtw89_write32(rtwdev, R_AX_LBC_WATCHDOG, lbc);
+
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1,
+			  B_AX_PCIE_TXRST_KEEP_REG | B_AX_PCIE_RXRST_KEEP_REG);
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_STOP_WPDMA);
+
+	/* stop DMA activities */
+	rtw89_pci_ctrl_dma_all(rtwdev, false);
+
+	/* check PCI at idle state */
+	check = B_AX_PCIEIO_BUSY | B_AX_PCIEIO_TX_BUSY | B_AX_PCIEIO_RX_BUSY;
+	ret = read_poll_timeout(rtw89_read32, dma_busy, (dma_busy & check) == 0,
+				100, 3000, false, rtwdev, R_AX_PCIE_DMA_BUSY1);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to poll io busy\n");
+		return ret;
+	}
+
+	rtw89_pci_clr_idx_all(rtwdev);
+
+	/* configure TX/RX op modes */
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_TX_TRUNC_MODE |
+						       B_AX_RX_TRUNC_MODE);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_RXBD_MODE);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_PCIE_MAX_TXDMA_MASK, 7);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_PCIE_MAX_RXDMA_MASK, 3);
+	/* multi-tag mode */
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_LATENCY_CONTROL);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_EXP_CTRL, B_AX_MAX_TAG_NUM,
+			   RTW89_MAC_TAG_NUM_8);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG2, B_AX_WD_ITVL_IDLE,
+			   RTW89_MAC_WD_DMA_INTVL_256NS);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG2, B_AX_WD_ITVL_ACT,
+			   RTW89_MAC_WD_DMA_INTVL_256NS);
+
+	/* fill TRX BD indexes */
+	rtw89_pci_ops_reset(rtwdev);
+
+	ret = rtw89_pci_rst_bdram_pcie(rtwdev);
+	if (ret) {
+		rtw89_warn(rtwdev, "reset bdram busy\n");
+		return ret;
+	}
+
+	/* enable FW CMD queue to download firmware */
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_TX_STOP1_ALL);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_STOP_CH12);
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP2, B_AX_TX_STOP2_ALL);
+
+	/* start DMA activities */
+	rtw89_pci_ctrl_dma_all(rtwdev, true);
+
+	return 0;
+}
+
+static int rtw89_pci_ltr_set(struct rtw89_dev *rtwdev)
+{
+	u32 val;
+
+	val = rtw89_read32(rtwdev, R_AX_LTR_CTRL_0);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+	val = rtw89_read32(rtwdev, R_AX_LTR_CTRL_1);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+	val = rtw89_read32(rtwdev, R_AX_LTR_IDLE_LATENCY);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+	val = rtw89_read32(rtwdev, R_AX_LTR_ACTIVE_LATENCY);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+
+	rtw89_write32_clr(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_HW_EN);
+	rtw89_write32_set(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_EN);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_SPACE_IDX_MASK,
+			   PCI_LTR_SPC_500US);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_IDLE_TIMER_IDX_MASK,
+			   PCI_LTR_IDLE_TIMER_800US);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_1, B_AX_LTR_RX0_TH_MASK, 0x28);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_1, B_AX_LTR_RX1_TH_MASK, 0x28);
+	rtw89_write32(rtwdev, R_AX_LTR_IDLE_LATENCY, 0x88e088e0);
+	rtw89_write32(rtwdev, R_AX_LTR_ACTIVE_LATENCY, 0x880b880b);
+
+	return 0;
+}
+
+static int rtw89_pci_ops_mac_post_init(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_pci_ltr_set(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "pci ltr set fail\n");
+		return ret;
+	}
+	if (rtwdev->chip->chip_id == RTL8852A) {
+		/* ltr sw trigger */
+		rtw89_write32_set(rtwdev, R_AX_LTR_CTRL_0, B_AX_APP_LTR_ACT);
+	}
+	/* ADDR info 8-byte mode */
+	rtw89_write32_set(rtwdev, R_AX_TX_ADDRESS_INFO_MODE_SETTING,
+			  B_AX_HOST_ADDR_INFO_8B_SEL);
+	rtw89_write32_clr(rtwdev, R_AX_PKTIN_SETTING, B_AX_WD_ADDR_INFO_LENGTH);
+
+	/* enable DMA for all queues */
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_TX_STOP1_ALL);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP2, B_AX_TX_STOP2_ALL);
+
+	/* Release PCI IO */
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1,
+			  B_AX_STOP_WPDMA | B_AX_STOP_PCIEIO);
+
+	return 0;
+}
+
+static int rtw89_pci_claim_device(struct rtw89_dev *rtwdev,
+				  struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	int ret;
+
+	ret = pci_enable_device(pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to enable pci device\n");
+		return ret;
+	}
+
+	pci_set_master(pdev);
+	pci_set_drvdata(pdev, rtwdev->hw);
+
+	rtwpci->pdev = pdev;
+
+	return 0;
+}
+
+static void rtw89_pci_declaim_device(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	pci_clear_master(pdev);
+	pci_disable_device(pdev);
+}
+
+static int rtw89_pci_setup_mapping(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long resource_len;
+	u8 bar_id = 2;
+	int ret;
+
+	ret = pci_request_regions(pdev, KBUILD_MODNAME);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to request pci regions\n");
+		goto err;
+	}
+
+	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		rtw89_err(rtwdev, "failed to set dma mask to 32-bit\n");
+		goto err_release_regions;
+	}
+
+	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		rtw89_err(rtwdev, "failed to set consistent dma mask to 32-bit\n");
+		goto err_release_regions;
+	}
+
+	resource_len = pci_resource_len(pdev, bar_id);
+	rtwpci->mmap = pci_iomap(pdev, bar_id, resource_len);
+	if (!rtwpci->mmap) {
+		rtw89_err(rtwdev, "failed to map pci io\n");
+		ret = -EIO;
+		goto err_release_regions;
+	}
+
+	return 0;
+
+err_release_regions:
+	pci_release_regions(pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_clear_mapping(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	if (rtwpci->mmap) {
+		pci_iounmap(pdev, rtwpci->mmap);
+		pci_release_regions(pdev);
+	}
+}
+
+static void rtw89_pci_free_tx_wd_ring(struct rtw89_dev *rtwdev,
+				      struct pci_dev *pdev,
+				      struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	u8 *head = wd_ring->head;
+	dma_addr_t dma = wd_ring->dma;
+	u32 page_size = wd_ring->page_size;
+	u32 page_num = wd_ring->page_num;
+	u32 ring_sz = page_size * page_num;
+
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+	wd_ring->head = NULL;
+}
+
+static void rtw89_pci_free_tx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_tx_ring *tx_ring)
+{
+	int ring_sz;
+	u8 *head;
+	dma_addr_t dma;
+
+	head = tx_ring->bd_ring.head;
+	dma = tx_ring->bd_ring.dma;
+	ring_sz = tx_ring->bd_ring.desc_size * tx_ring->bd_ring.len;
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+
+	tx_ring->bd_ring.head = NULL;
+}
+
+static void rtw89_pci_free_tx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	int i;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		rtw89_pci_free_tx_wd_ring(rtwdev, pdev, tx_ring);
+		rtw89_pci_free_tx_ring(rtwdev, pdev, tx_ring);
+	}
+}
+
+static void rtw89_pci_free_rx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_rx_ring *rx_ring)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	struct sk_buff *skb;
+	dma_addr_t dma;
+	u32 buf_sz;
+	u8 *head;
+	int ring_sz = rx_ring->bd_ring.desc_size * rx_ring->bd_ring.len;
+	int i;
+
+	buf_sz = rx_ring->buf_sz;
+	for (i = 0; i < rx_ring->bd_ring.len; i++) {
+		skb = rx_ring->buf[i];
+		if (!skb)
+			continue;
+
+		rx_info = RTW89_PCI_RX_SKB_CB(skb);
+		dma = rx_info->dma;
+		dma_unmap_single(&pdev->dev, dma, buf_sz, DMA_FROM_DEVICE);
+		dev_kfree_skb(skb);
+		rx_ring->buf[i] = NULL;
+	}
+
+	head = rx_ring->bd_ring.head;
+	dma = rx_ring->bd_ring.dma;
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+
+	rx_ring->bd_ring.head = NULL;
+}
+
+static void rtw89_pci_free_rx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_rx_ring *rx_ring;
+	int i;
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		rtw89_pci_free_rx_ring(rtwdev, pdev, rx_ring);
+	}
+}
+
+static void rtw89_pci_free_trx_rings(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	rtw89_pci_free_rx_rings(rtwdev, pdev);
+	rtw89_pci_free_tx_rings(rtwdev, pdev);
+}
+
+static int rtw89_pci_init_rx_bd(struct rtw89_dev *rtwdev, struct pci_dev *pdev,
+				struct rtw89_pci_rx_ring *rx_ring,
+				struct sk_buff *skb, int buf_sz, u32 idx)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	struct rtw89_pci_rx_bd_32 *rx_bd;
+	dma_addr_t dma;
+
+	if (!skb)
+		return -EINVAL;
+
+	dma = dma_map_single(&pdev->dev, skb->data, buf_sz, DMA_FROM_DEVICE);
+	if (dma_mapping_error(&pdev->dev, dma))
+		return -EBUSY;
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	rx_bd = RTW89_PCI_RX_BD(rx_ring, idx);
+
+	memset(rx_bd, 0, sizeof(*rx_bd));
+	rx_bd->buf_size = cpu_to_le16(buf_sz);
+	rx_bd->dma = cpu_to_le32(dma);
+	rx_info->dma = dma;
+
+	return 0;
+}
+
+static int rtw89_pci_alloc_tx_wd_ring(struct rtw89_dev *rtwdev,
+				      struct pci_dev *pdev,
+				      struct rtw89_pci_tx_ring *tx_ring,
+				      enum rtw89_tx_channel txch)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	dma_addr_t dma;
+	dma_addr_t cur_paddr;
+	u8 *head;
+	u8 *cur_vaddr;
+	u32 page_size = RTW89_PCI_TXWD_PAGE_SIZE;
+	u32 page_num = RTW89_PCI_TXWD_NUM_MAX;
+	u32 ring_sz = page_size * page_num;
+	u32 page_offset;
+	int i;
+
+	/* FWCMD queue doesn't use txwd as pages */
+	if (txch == RTW89_TXCH_CH12)
+		return 0;
+
+	head = dma_alloc_coherent(&pdev->dev, ring_sz, &dma, GFP_KERNEL);
+	if (!head)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&wd_ring->free_pages);
+	wd_ring->head = head;
+	wd_ring->dma = dma;
+	wd_ring->page_size = page_size;
+	wd_ring->page_num = page_num;
+
+	page_offset = 0;
+	for (i = 0; i < page_num; i++) {
+		txwd = &wd_ring->pages[i];
+		cur_paddr = dma + page_offset;
+		cur_vaddr = head + page_offset;
+
+		skb_queue_head_init(&txwd->queue);
+		INIT_LIST_HEAD(&txwd->list);
+		txwd->paddr = cur_paddr;
+		txwd->vaddr = cur_vaddr;
+		txwd->len = page_size;
+		txwd->seq = i;
+		rtw89_pci_enqueue_txwd(tx_ring, txwd);
+
+		page_offset += page_size;
+	}
+
+	return 0;
+}
+
+static int rtw89_pci_alloc_tx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_tx_ring *tx_ring,
+				   u32 desc_size, u32 len,
+				   enum rtw89_tx_channel txch)
+{
+	int ring_sz = desc_size * len;
+	u8 *head;
+	dma_addr_t dma;
+	u32 addr_num;
+	u32 addr_idx;
+	u32 addr_bdram;
+	u32 addr_desa_l;
+	u32 addr_desa_h;
+	int ret;
+
+	ret = rtw89_pci_alloc_tx_wd_ring(rtwdev, pdev, tx_ring, txch);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc txwd ring of txch %d\n", txch);
+		goto err;
+	}
+
+	ret = rtw89_pci_get_txch_addrs(txch, &addr_num, &addr_idx, &addr_bdram,
+				       &addr_desa_l, &addr_desa_h);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get address of txch %d", txch);
+		goto err_free_wd_ring;
+	}
+
+	head = dma_alloc_coherent(&pdev->dev, ring_sz, &dma, GFP_KERNEL);
+	if (!head) {
+		ret = -ENOMEM;
+		goto err_free_wd_ring;
+	}
+
+	INIT_LIST_HEAD(&tx_ring->busy_pages);
+	tx_ring->bd_ring.head = head;
+	tx_ring->bd_ring.dma = dma;
+	tx_ring->bd_ring.len = len;
+	tx_ring->bd_ring.desc_size = desc_size;
+	tx_ring->bd_ring.addr_num = addr_num;
+	tx_ring->bd_ring.addr_idx = addr_idx;
+	tx_ring->bd_ring.addr_bdram = addr_bdram;
+	tx_ring->bd_ring.addr_desa_l = addr_desa_l;
+	tx_ring->bd_ring.addr_desa_h = addr_desa_h;
+	tx_ring->bd_ring.wp = 0;
+	tx_ring->bd_ring.rp = 0;
+	tx_ring->txch = txch;
+
+	return 0;
+
+err_free_wd_ring:
+	rtw89_pci_free_tx_wd_ring(rtwdev, pdev, tx_ring);
+err:
+	return ret;
+}
+
+static int rtw89_pci_alloc_tx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	u32 desc_size;
+	u32 len;
+	u32 i, tx_allocated;
+	int ret;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		desc_size = sizeof(struct rtw89_pci_tx_bd_32);
+		len = RTW89_PCI_TXBD_NUM_MAX;
+		ret = rtw89_pci_alloc_tx_ring(rtwdev, pdev, tx_ring,
+					      desc_size, len, i);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to alloc tx ring %d\n", i);
+			goto err_free;
+		}
+	}
+
+	return 0;
+
+err_free:
+	tx_allocated = i;
+	for (i = 0; i < tx_allocated; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		rtw89_pci_free_tx_ring(rtwdev, pdev, tx_ring);
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_alloc_rx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_rx_ring *rx_ring,
+				   u32 desc_size, u32 len, u32 rxch)
+{
+	struct sk_buff *skb;
+	u8 *head;
+	dma_addr_t dma;
+	u32 addr_num;
+	u32 addr_idx;
+	u32 addr_desa_l;
+	u32 addr_desa_h;
+	int ring_sz = desc_size * len;
+	int buf_sz = RTW89_PCI_RX_BUF_SIZE;
+	int i, allocated;
+	int ret;
+
+	ret = rtw89_pci_get_rxch_addrs(rxch, &addr_num, &addr_idx,
+				       &addr_desa_l, &addr_desa_h);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get address of rxch %d", rxch);
+		return ret;
+	}
+
+	head = dma_alloc_coherent(&pdev->dev, ring_sz, &dma, GFP_KERNEL);
+	if (!head) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	rx_ring->bd_ring.head = head;
+	rx_ring->bd_ring.dma = dma;
+	rx_ring->bd_ring.len = len;
+	rx_ring->bd_ring.desc_size = desc_size;
+	rx_ring->bd_ring.addr_num = addr_num;
+	rx_ring->bd_ring.addr_idx = addr_idx;
+	rx_ring->bd_ring.addr_desa_l = addr_desa_l;
+	rx_ring->bd_ring.addr_desa_h = addr_desa_h;
+	rx_ring->bd_ring.wp = 0;
+	rx_ring->bd_ring.rp = 0;
+	rx_ring->buf_sz = buf_sz;
+	rx_ring->diliver_skb = NULL;
+	rx_ring->diliver_desc.ready = false;
+
+	for (i = 0; i < len; i++) {
+		skb = dev_alloc_skb(buf_sz);
+		if (!skb) {
+			ret = -ENOMEM;
+			goto err_free;
+		}
+
+		memset(skb->data, 0, buf_sz);
+		rx_ring->buf[i] = skb;
+		ret = rtw89_pci_init_rx_bd(rtwdev, pdev, rx_ring, skb,
+					   buf_sz, i);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to init rx buf %d\n", i);
+			dev_kfree_skb_any(skb);
+			rx_ring->buf[i] = NULL;
+			goto err_free;
+		}
+	}
+
+	return 0;
+
+err_free:
+	allocated = i;
+	for (i = 0; i < allocated; i++) {
+		skb = rx_ring->buf[i];
+		if (!skb)
+			continue;
+		dma = *((dma_addr_t *)skb->cb);
+		dma_unmap_single(&pdev->dev, dma, buf_sz, DMA_FROM_DEVICE);
+		dev_kfree_skb(skb);
+		rx_ring->buf[i] = NULL;
+	}
+
+	head = rx_ring->bd_ring.head;
+	dma = rx_ring->bd_ring.dma;
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+
+	rx_ring->bd_ring.head = NULL;
+err:
+	return ret;
+}
+
+static int rtw89_pci_alloc_rx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 desc_size;
+	u32 len;
+	int i, rx_allocated;
+	int ret;
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		desc_size = sizeof(struct rtw89_pci_rx_bd_32);
+		len = RTW89_PCI_RXBD_NUM_MAX;
+		ret = rtw89_pci_alloc_rx_ring(rtwdev, pdev, rx_ring,
+					      desc_size, len, i);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to alloc rx ring %d\n", i);
+			goto err_free;
+		}
+	}
+
+	return 0;
+
+err_free:
+	rx_allocated = i;
+	for (i = 0; i < rx_allocated; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		rtw89_pci_free_rx_ring(rtwdev, pdev, rx_ring);
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_alloc_trx_rings(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	int ret;
+
+	ret = rtw89_pci_alloc_tx_rings(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc dma tx rings\n");
+		goto err;
+	}
+
+	ret = rtw89_pci_alloc_rx_rings(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc dma rx rings\n");
+		goto err_free_tx_rings;
+	}
+
+	return 0;
+
+err_free_tx_rings:
+	rtw89_pci_free_tx_rings(rtwdev, pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_h2c_init(struct rtw89_dev *rtwdev,
+			       struct rtw89_pci *rtwpci)
+{
+	skb_queue_head_init(&rtwpci->h2c_queue);
+	skb_queue_head_init(&rtwpci->h2c_release_queue);
+}
+
+static int rtw89_pci_setup_resource(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	int ret;
+
+	ret = rtw89_pci_setup_mapping(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to setup pci mapping\n");
+		goto err;
+	}
+
+	ret = rtw89_pci_alloc_trx_rings(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc pci trx rings\n");
+		goto err_pci_unmap;
+	}
+
+	rtw89_pci_h2c_init(rtwdev, rtwpci);
+
+	spin_lock_init(&rtwpci->irq_lock);
+	spin_lock_init(&rtwpci->trx_lock);
+
+	return 0;
+
+err_pci_unmap:
+	rtw89_pci_clear_mapping(rtwdev, pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_clear_resource(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	rtw89_pci_free_trx_rings(rtwdev, pdev);
+	rtw89_pci_clear_mapping(rtwdev, pdev);
+	rtw89_pci_release_fwcmd(rtwdev, rtwpci,
+				skb_queue_len(&rtwpci->h2c_queue), true);
+}
+
+static void rtw89_pci_default_intr_mask(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	rtwpci->halt_c2h_intrs = B_AX_HALT_C2H_INT_EN | 0;
+	rtwpci->intrs[0] = B_AX_TXDMA_STUCK_INT_EN |
+			   B_AX_RXDMA_INT_EN |
+			   B_AX_RXP1DMA_INT_EN |
+			   B_AX_RPQDMA_INT_EN |
+			   B_AX_RXDMA_STUCK_INT_EN |
+			   B_AX_RDU_INT_EN |
+			   B_AX_RPQBD_FULL_INT_EN |
+			   B_AX_HS0ISR_IND_INT_EN;
+
+	rtwpci->intrs[1] = B_AX_HC10ISR_IND_INT_EN;
+}
+
+static int rtw89_pci_request_irq(struct rtw89_dev *rtwdev,
+				 struct pci_dev *pdev)
+{
+	unsigned long flags = 0;
+	int ret;
+
+	flags |= PCI_IRQ_LEGACY | PCI_IRQ_MSI;
+	ret = pci_alloc_irq_vectors(pdev, 1, 1, flags);
+	if (ret < 0) {
+		rtw89_err(rtwdev, "failed to alloc irq vectors, ret %d\n", ret);
+		goto err;
+	}
+
+	ret = devm_request_threaded_irq(rtwdev->dev, pdev->irq,
+					rtw89_pci_interrupt_handler,
+					rtw89_pci_interrupt_threadfn,
+					IRQF_SHARED, KBUILD_MODNAME, rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to request threaded irq\n");
+		goto err_free_vector;
+	}
+
+	rtw89_pci_default_intr_mask(rtwdev);
+
+	return 0;
+
+err_free_vector:
+	pci_free_irq_vectors(pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_free_irq(struct rtw89_dev *rtwdev,
+			       struct pci_dev *pdev)
+{
+	devm_free_irq(rtwdev->dev, pdev->irq, rtwdev);
+	pci_free_irq_vectors(pdev);
+}
+
+static void rtw89_pci_clkreq_set(struct rtw89_dev *rtwdev, bool enable)
+{
+	int ret;
+
+	if (rtw89_pci_disable_clkreq)
+		return;
+
+	ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_CLK_CTRL,
+			       PCIE_CLKDLY_HW_30US);
+	if (ret)
+		rtw89_err(rtwdev, "failed to set CLKREQ Delay\n");
+
+	if (enable)
+		ret = rtw89_dbi_write8_set(rtwdev, RTW89_PCIE_L1_CTRL,
+					   RTW89_PCIE_BIT_CLK);
+	else
+		ret = rtw89_dbi_write8_clr(rtwdev, RTW89_PCIE_L1_CTRL,
+					   RTW89_PCIE_BIT_CLK);
+	if (ret)
+		rtw89_err(rtwdev, "failed to %s CLKREQ_L1, ret=%d",
+			  enable ? "set" : "unset", ret);
+}
+
+static void rtw89_pci_aspm_set(struct rtw89_dev *rtwdev, bool enable)
+{
+	u8 value = 0;
+	int ret;
+
+	if (rtw89_pci_disable_aspm_l1)
+		return;
+
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_ASPM_CTRL, &value);
+	if (ret)
+		rtw89_err(rtwdev, "failed to read ASPM Delay\n");
+
+	value &= ~(RTW89_L1DLY_MASK | RTW89_L0DLY_MASK);
+	value |= FIELD_PREP(RTW89_L1DLY_MASK, PCIE_L1DLY_16US) |
+		 FIELD_PREP(RTW89_L0DLY_MASK, PCIE_L0SDLY_4US);
+
+	ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_ASPM_CTRL, value);
+	if (ret)
+		rtw89_err(rtwdev, "failed to read ASPM Delay\n");
+
+	if (enable)
+		ret = rtw89_dbi_write8_set(rtwdev, RTW89_PCIE_L1_CTRL,
+					   RTW89_PCIE_BIT_L1);
+	else
+		ret = rtw89_dbi_write8_clr(rtwdev, RTW89_PCIE_L1_CTRL,
+					   RTW89_PCIE_BIT_L1);
+	if (ret)
+		rtw89_err(rtwdev, "failed to %s ASPM L1, ret=%d",
+			  enable ? "set" : "unset", ret);
+}
+
+static void rtw89_pci_recalc_int_mit(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_traffic_stats *stats = &rtwdev->stats;
+	enum rtw89_tfc_lv tx_tfc_lv = stats->tx_tfc_lv;
+	enum rtw89_tfc_lv rx_tfc_lv = stats->rx_tfc_lv;
+	u32 val = 0;
+
+	if (!rtwdev->scanning &&
+	    (tx_tfc_lv >= RTW89_TFC_HIGH || rx_tfc_lv >= RTW89_TFC_HIGH))
+		val = B_AX_RXMIT_RXP2_SEL | B_AX_RXMIT_RXP1_SEL |
+		      FIELD_PREP(B_AX_RXCOUNTER_MATCH_MASK, RTW89_PCI_RXBD_NUM_MAX / 2) |
+		      FIELD_PREP(B_AX_RXTIMER_UNIT_MASK, AX_RXTIMER_UNIT_64US) |
+		      FIELD_PREP(B_AX_RXTIMER_MATCH_MASK, 2048 / 64);
+
+	rtw89_write32(rtwdev, R_AX_INT_MIT_RX, val);
+}
+
+static void rtw89_pci_link_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct pci_dev *pdev = rtwpci->pdev;
+	u16 link_ctrl;
+	int ret;
+
+	/* Though there is standard PCIE configuration space to set the
+	 * link control register, but by Realtek's design, driver should
+	 * check if host supports CLKREQ/ASPM to enable the HW module.
+	 *
+	 * These functions are implemented by two HW modules associated,
+	 * one is responsible to access PCIE configuration space to
+	 * follow the host settings, and another is in charge of doing
+	 * CLKREQ/ASPM mechanisms, it is default disabled. Because sometimes
+	 * the host does not support it, and due to some reasons or wrong
+	 * settings (ex. CLKREQ# not Bi-Direction), it could lead to device
+	 * loss if HW misbehaves on the link.
+	 *
+	 * Hence it's designed that driver should first check the PCIE
+	 * configuration space is sync'ed and enabled, then driver can turn
+	 * on the other module that is actually working on the mechanism.
+	 */
+	ret = pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &link_ctrl);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to read PCI cap, ret=%d\n", ret);
+		return;
+	}
+
+	if (link_ctrl & PCI_EXP_LNKCTL_CLKREQ_EN)
+		rtw89_pci_clkreq_set(rtwdev, true);
+
+	if (link_ctrl & PCI_EXP_LNKCTL_ASPM_L1)
+		rtw89_pci_aspm_set(rtwdev, true);
+}
+
+static void rtw89_pci_l1ss_set(struct rtw89_dev *rtwdev, bool enable)
+{
+	int ret;
+
+	if (enable)
+		ret = rtw89_dbi_write8_set(rtwdev, RTW89_PCIE_TIMER_CTRL,
+					   RTW89_PCIE_BIT_L1SUB);
+	else
+		ret = rtw89_dbi_write8_clr(rtwdev, RTW89_PCIE_TIMER_CTRL,
+					   RTW89_PCIE_BIT_L1SUB);
+	if (ret)
+		rtw89_err(rtwdev, "failed to %s L1SS, ret=%d",
+			  enable ? "set" : "unset", ret);
+}
+
+static void rtw89_pci_l1ss_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct pci_dev *pdev = rtwpci->pdev;
+	u32 l1ss_cap_ptr, l1ss_ctrl;
+
+	if (rtw89_pci_disable_l1ss)
+		return;
+
+	l1ss_cap_ptr = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
+	if (!l1ss_cap_ptr)
+		return;
+
+	pci_read_config_dword(pdev, l1ss_cap_ptr + PCI_L1SS_CTL1, &l1ss_ctrl);
+
+	if (l1ss_ctrl & PCI_L1SS_CTL1_L1SS_MASK)
+		rtw89_pci_l1ss_set(rtwdev, true);
+}
+
+static void rtw89_pci_ctrl_dma_all_pcie(struct rtw89_dev *rtwdev, u8 en)
+{
+	u32 val32;
+
+	if (en == MAC_AX_FUNC_EN) {
+		val32 = B_AX_STOP_PCIEIO;
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1, val32);
+
+		val32 = B_AX_TXHCI_EN | B_AX_RXHCI_EN;
+		rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, val32);
+	} else {
+		val32 = B_AX_STOP_PCIEIO;
+		rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1, val32);
+
+		val32 = B_AX_TXHCI_EN | B_AX_RXHCI_EN;
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1, val32);
+	}
+}
+
+static int rtw89_pci_poll_io_idle(struct rtw89_dev *rtwdev)
+{
+	int ret = 0;
+	u32 sts;
+	u32 busy = B_AX_PCIEIO_BUSY | B_AX_PCIEIO_TX_BUSY | B_AX_PCIEIO_RX_BUSY;
+
+	ret = read_poll_timeout_atomic(rtw89_read32, sts, (sts & busy) == 0x0,
+				       10, 1000, false, rtwdev,
+				       R_AX_PCIE_DMA_BUSY1);
+	if (ret) {
+		rtw89_err(rtwdev, "pci dmach busy1 0x%X\n",
+			  rtw89_read32(rtwdev, R_AX_PCIE_DMA_BUSY1));
+		return -EINVAL;
+	}
+	return ret;
+}
+
+static int rtw89_pci_lv1rst_stop_dma(struct rtw89_dev *rtwdev)
+{
+	u32 val, dma_rst = 0;
+	int ret;
+
+	rtw89_pci_ctrl_dma_all_pcie(rtwdev, MAC_AX_FUNC_DIS);
+	ret = rtw89_pci_poll_io_idle(rtwdev);
+	if (ret) {
+		val = rtw89_read32(rtwdev, R_AX_DBG_ERR_FLAG);
+		rtw89_debug(rtwdev, RTW89_DBG_HCI,
+			    "[PCIe] poll_io_idle fail, before 0x%08x: 0x%08x\n",
+			    R_AX_DBG_ERR_FLAG, val);
+		if (val & B_AX_TX_STUCK || val & B_AX_PCIE_TXBD_LEN0)
+			dma_rst |= B_AX_HCI_TXDMA_EN;
+		if (val & B_AX_RX_STUCK)
+			dma_rst |= B_AX_HCI_RXDMA_EN;
+		val = rtw89_read32(rtwdev, R_AX_HCI_FUNC_EN);
+		rtw89_write32(rtwdev, R_AX_HCI_FUNC_EN, val & ~dma_rst);
+		rtw89_write32(rtwdev, R_AX_HCI_FUNC_EN, val | dma_rst);
+		ret = rtw89_pci_poll_io_idle(rtwdev);
+		val = rtw89_read32(rtwdev, R_AX_DBG_ERR_FLAG);
+		rtw89_debug(rtwdev, RTW89_DBG_HCI,
+			    "[PCIe] poll_io_idle fail, after 0x%08x: 0x%08x\n",
+			    R_AX_DBG_ERR_FLAG, val);
+	}
+
+	return ret;
+}
+
+static void rtw89_pci_ctrl_hci_dma_en(struct rtw89_dev *rtwdev, u8 en)
+{
+	u32 val32;
+
+	if (en == MAC_AX_FUNC_EN) {
+		val32 = B_AX_HCI_TXDMA_EN | B_AX_HCI_RXDMA_EN;
+		rtw89_write32_set(rtwdev, R_AX_HCI_FUNC_EN, val32);
+	} else {
+		val32 = B_AX_HCI_TXDMA_EN | B_AX_HCI_RXDMA_EN;
+		rtw89_write32_clr(rtwdev, R_AX_HCI_FUNC_EN, val32);
+	}
+}
+
+static int rtw89_pci_rst_bdram(struct rtw89_dev *rtwdev)
+{
+	int ret = 0;
+	u32 val32, sts;
+
+	val32 = B_AX_RST_BDRAM;
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, val32);
+
+	ret = read_poll_timeout_atomic(rtw89_read32, sts,
+				       (sts & B_AX_RST_BDRAM) == 0x0, 1, 100,
+				       true, rtwdev, R_AX_PCIE_INIT_CFG1);
+	return ret;
+}
+
+static int rtw89_pci_lv1rst_start_dma(struct rtw89_dev *rtwdev)
+{
+	u32 ret;
+
+	rtw89_pci_ctrl_hci_dma_en(rtwdev, MAC_AX_FUNC_DIS);
+	rtw89_pci_ctrl_hci_dma_en(rtwdev, MAC_AX_FUNC_EN);
+	rtw89_pci_clr_idx_all(rtwdev);
+
+	ret = rtw89_pci_rst_bdram(rtwdev);
+	if (ret)
+		return ret;
+
+	rtw89_pci_ctrl_dma_all_pcie(rtwdev, MAC_AX_FUNC_EN);
+	return ret;
+}
+
+static int rtw89_pci_ops_mac_lv1_recovery(struct rtw89_dev *rtwdev,
+					  enum rtw89_lv1_rcvy_step step)
+{
+	int ret;
+
+	switch (step) {
+	case RTW89_LV1_RCVY_STEP_1:
+		ret = rtw89_pci_lv1rst_stop_dma(rtwdev);
+		if (ret)
+			rtw89_err(rtwdev, "lv1 rcvy pci stop dma fail\n");
+
+		break;
+
+	case RTW89_LV1_RCVY_STEP_2:
+		ret = rtw89_pci_lv1rst_start_dma(rtwdev);
+		if (ret)
+			rtw89_err(rtwdev, "lv1 rcvy pci start dma fail\n");
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static void rtw89_pci_ops_dump_err_status(struct rtw89_dev *rtwdev)
+{
+	rtw89_info(rtwdev, "R_AX_RPQ_RXBD_IDX =0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_RPQ_RXBD_IDX));
+	rtw89_info(rtwdev, "R_AX_DBG_ERR_FLAG=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_DBG_ERR_FLAG));
+	rtw89_info(rtwdev, "R_AX_LBC_WATCHDOG=0x%08x\n",
+		   rtw89_read32(rtwdev, R_AX_LBC_WATCHDOG));
+}
+
+static int rtw89_pci_napi_poll(struct napi_struct *napi, int budget)
+{
+	struct rtw89_dev *rtwdev = container_of(napi, struct rtw89_dev, napi);
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long flags;
+	int work_done;
+
+	rtwdev->napi_budget_countdown = budget;
+
+	rtw89_pci_clear_isr0(rtwdev, B_AX_RPQDMA_INT | B_AX_RPQBD_FULL_INT);
+	work_done = rtw89_pci_poll_rpq_dma(rtwdev, rtwpci, rtwdev->napi_budget_countdown);
+	if (work_done == budget)
+		return budget;
+
+	rtw89_pci_clear_isr0(rtwdev, B_AX_RXP1DMA_INT | B_AX_RXDMA_INT | B_AX_RDU_INT);
+	work_done += rtw89_pci_poll_rxq_dma(rtwdev, rtwpci, rtwdev->napi_budget_countdown);
+	if (work_done < budget && napi_complete_done(napi, work_done)) {
+		spin_lock_irqsave(&rtwpci->irq_lock, flags);
+		if (likely(rtwpci->running))
+			rtw89_pci_enable_intr(rtwdev, rtwpci);
+		spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+	}
+
+	return work_done;
+}
+
+static int __maybe_unused rtw89_pci_suspend(struct device *dev)
+{
+	struct ieee80211_hw *hw = dev_get_drvdata(dev);
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	rtw89_write32_clr(rtwdev, R_AX_SYS_SDIO_CTRL,
+			  B_AX_PCIE_DIS_L2_CTRL_LDO_HCI);
+	rtw89_write32_set(rtwdev, R_AX_RSV_CTRL, B_AX_WLOCK_1C_BIT6);
+	rtw89_write32_set(rtwdev, R_AX_RSV_CTRL, B_AX_R_DIS_PRST);
+	rtw89_write32_clr(rtwdev, R_AX_RSV_CTRL, B_AX_WLOCK_1C_BIT6);
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1,
+			  B_AX_PCIE_PERST_KEEP_REG | B_AX_PCIE_TRAIN_KEEP_REG);
+
+	return 0;
+}
+
+static void rtw89_pci_l2_hci_ldo(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	/* Hardware need write the reg twice to ensure the setting work */
+	rtw89_dbi_write8_set(rtwdev, RTW89_PCIE_RST_MSTATE,
+			     RTW89_PCIE_BIT_CFG_RST_MSTATE);
+	rtw89_dbi_write8_set(rtwdev, RTW89_PCIE_RST_MSTATE,
+			     RTW89_PCIE_BIT_CFG_RST_MSTATE);
+}
+
+static int __maybe_unused rtw89_pci_resume(struct device *dev)
+{
+	struct ieee80211_hw *hw = dev_get_drvdata(dev);
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	rtw89_write32_set(rtwdev, R_AX_SYS_SDIO_CTRL,
+			  B_AX_PCIE_DIS_L2_CTRL_LDO_HCI);
+	rtw89_write32_set(rtwdev, R_AX_RSV_CTRL, B_AX_WLOCK_1C_BIT6);
+	rtw89_write32_clr(rtwdev, R_AX_RSV_CTRL, B_AX_R_DIS_PRST);
+	rtw89_write32_clr(rtwdev, R_AX_RSV_CTRL, B_AX_WLOCK_1C_BIT6);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1,
+			  B_AX_PCIE_PERST_KEEP_REG | B_AX_PCIE_TRAIN_KEEP_REG);
+	rtw89_pci_l2_hci_ldo(rtwdev);
+	rtw89_pci_link_cfg(rtwdev);
+	rtw89_pci_l1ss_cfg(rtwdev);
+
+	return 0;
+}
+
+SIMPLE_DEV_PM_OPS(rtw89_pm_ops, rtw89_pci_suspend, rtw89_pci_resume);
+EXPORT_SYMBOL(rtw89_pm_ops);
+
+static const struct rtw89_hci_ops rtw89_pci_ops = {
+	.tx_write	= rtw89_pci_ops_tx_write,
+	.tx_kick_off	= rtw89_pci_ops_tx_kick_off,
+	.flush_queues	= rtw89_pci_ops_flush_queues,
+	.reset		= rtw89_pci_ops_reset,
+	.start		= rtw89_pci_ops_start,
+	.stop		= rtw89_pci_ops_stop,
+	.recalc_int_mit = rtw89_pci_recalc_int_mit,
+
+	.read8		= rtw89_pci_ops_read8,
+	.read16		= rtw89_pci_ops_read16,
+	.read32		= rtw89_pci_ops_read32,
+	.write8		= rtw89_pci_ops_write8,
+	.write16	= rtw89_pci_ops_write16,
+	.write32	= rtw89_pci_ops_write32,
+
+	.mac_pre_init	= rtw89_pci_ops_mac_pre_init,
+	.mac_post_init	= rtw89_pci_ops_mac_post_init,
+	.deinit		= rtw89_pci_ops_deinit,
+
+	.check_and_reclaim_tx_resource = rtw89_pci_check_and_reclaim_tx_resource,
+	.mac_lv1_rcvy	= rtw89_pci_ops_mac_lv1_recovery,
+	.dump_err_status = rtw89_pci_ops_dump_err_status,
+	.napi_poll	= rtw89_pci_napi_poll,
+};
+
+static int rtw89_pci_probe(struct pci_dev *pdev,
+			   const struct pci_device_id *id)
+{
+	struct ieee80211_hw *hw;
+	struct rtw89_dev *rtwdev;
+	int driver_data_size;
+	int ret;
+
+	driver_data_size = sizeof(struct rtw89_dev) + sizeof(struct rtw89_pci);
+	hw = ieee80211_alloc_hw(driver_data_size, &rtw89_ops);
+	if (!hw) {
+		dev_err(&pdev->dev, "failed to allocate hw\n");
+		return -ENOMEM;
+	}
+
+	rtwdev = hw->priv;
+	rtwdev->hw = hw;
+	rtwdev->dev = &pdev->dev;
+	rtwdev->hci.ops = &rtw89_pci_ops;
+	rtwdev->hci.type = RTW89_HCI_TYPE_PCIE;
+	rtwdev->hci.rpwm_addr = R_AX_PCIE_HRPWM;
+	rtwdev->hci.cpwm_addr = R_AX_CPWM;
+
+	SET_IEEE80211_DEV(rtwdev->hw, &pdev->dev);
+
+	switch (id->driver_data) {
+	case RTL8852A:
+		rtwdev->chip = &rtw8852a_chip_info;
+		break;
+	default:
+		return -ENOENT;
+	}
+
+	ret = rtw89_core_init(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to initialise core\n");
+		goto err_release_hw;
+	}
+
+	ret = rtw89_pci_claim_device(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to claim pci device\n");
+		goto err_core_deinit;
+	}
+
+	ret = rtw89_pci_setup_resource(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to setup pci resource\n");
+		goto err_declaim_pci;
+	}
+
+	ret = rtw89_chip_info_setup(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to setup chip information\n");
+		goto err_clear_resource;
+	}
+
+	rtw89_pci_link_cfg(rtwdev);
+	rtw89_pci_l1ss_cfg(rtwdev);
+
+	ret = rtw89_core_register(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to register core\n");
+		goto err_clear_resource;
+	}
+
+	rtw89_core_napi_init(rtwdev);
+
+	ret = rtw89_pci_request_irq(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to request pci irq\n");
+		goto err_unregister;
+	}
+
+	return 0;
+
+err_unregister:
+	rtw89_core_napi_deinit(rtwdev);
+	rtw89_core_unregister(rtwdev);
+err_clear_resource:
+	rtw89_pci_clear_resource(rtwdev, pdev);
+err_declaim_pci:
+	rtw89_pci_declaim_device(rtwdev, pdev);
+err_core_deinit:
+	rtw89_core_deinit(rtwdev);
+err_release_hw:
+	ieee80211_free_hw(hw);
+
+	return ret;
+}
+
+static void rtw89_pci_remove(struct pci_dev *pdev)
+{
+	struct ieee80211_hw *hw = pci_get_drvdata(pdev);
+	struct rtw89_dev *rtwdev;
+
+	rtwdev = hw->priv;
+
+	rtw89_pci_free_irq(rtwdev, pdev);
+	rtw89_core_napi_deinit(rtwdev);
+	rtw89_core_unregister(rtwdev);
+	rtw89_pci_clear_resource(rtwdev, pdev);
+	rtw89_pci_declaim_device(rtwdev, pdev);
+	rtw89_core_deinit(rtwdev);
+	ieee80211_free_hw(hw);
+}
+
+static const struct pci_device_id rtw89_pci_id_table[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8852), .driver_data = RTL8852A },
+	{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0xa85a), .driver_data = RTL8852A },
+	{},
+};
+MODULE_DEVICE_TABLE(pci, rtw89_pci_id_table);
+
+static struct pci_driver rtw89_pci_driver = {
+	.name		= "rtw89_pci",
+	.id_table	= rtw89_pci_id_table,
+	.probe		= rtw89_pci_probe,
+	.remove		= rtw89_pci_remove,
+	.driver.pm	= &rtw89_pm_ops,
+};
+module_pci_driver(rtw89_pci_driver);
+
+MODULE_AUTHOR("Realtek Corporation");
+MODULE_DESCRIPTION("Realtek 802.11ax wireless PCI driver");
+MODULE_LICENSE("Dual BSD/GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/pci.h
@@ -0,0 +1,635 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_PCI_H__
+#define __RTW89_PCI_H__
+
+#include "txrx.h"
+
+#define MDIO_PG0_G1 0
+#define MDIO_PG1_G1 1
+#define MDIO_PG0_G2 2
+#define MDIO_PG1_G2 3
+#define RAC_ANA10			0x10
+#define RAC_ANA19			0x19
+#define RAC_ANA1F			0x1F
+#define RAC_ANA24			0x24
+#define B_AX_DEGLITCH			GENMASK(11, 8)
+#define RAC_ANA26			0x26
+#define B_AX_RXEN			GENMASK(15, 14)
+#define RAC_CTRL_PPR_V1			0x30
+#define B_AX_CLK_CALIB_EN		BIT(12)
+#define B_AX_CALIB_EN			BIT(13)
+#define B_AX_DIV			GENMASK(15, 14)
+#define RAC_SET_PPR_V1			0x31
+
+#define R_AX_DBI_FLAG			0x1090
+#define B_AX_DBI_RFLAG			BIT(17)
+#define B_AX_DBI_WFLAG			BIT(16)
+#define B_AX_DBI_WREN_MSK		GENMASK(15, 12)
+#define B_AX_DBI_ADDR_MSK		GENMASK(11, 2)
+#define R_AX_DBI_WDATA			0x1094
+#define R_AX_DBI_RDATA			0x1098
+
+#define R_AX_MDIO_WDATA			0x10A4
+#define R_AX_MDIO_RDATA			0x10A6
+
+#define RTW89_PCI_WR_RETRY_CNT		20
+
+/* Interrupts */
+#define R_AX_HIMR0 0x01A0
+#define B_AX_HALT_C2H_INT_EN BIT(21)
+#define R_AX_HISR0 0x01A4
+
+#define R_AX_MDIO_CFG			0x10A0
+#define B_AX_MDIO_PHY_ADDR_MASK		GENMASK(13, 12)
+#define B_AX_MDIO_RFLAG			BIT(9)
+#define B_AX_MDIO_WFLAG			BIT(8)
+#define B_AX_MDIO_ADDR_MASK		GENMASK(4, 0)
+
+#define R_AX_PCIE_HIMR00	0x10B0
+#define B_AX_HC00ISR_IND_INT_EN		BIT(27)
+#define B_AX_HD1ISR_IND_INT_EN		BIT(26)
+#define B_AX_HD0ISR_IND_INT_EN		BIT(25)
+#define B_AX_HS0ISR_IND_INT_EN		BIT(24)
+#define B_AX_RETRAIN_INT_EN		BIT(21)
+#define B_AX_RPQBD_FULL_INT_EN		BIT(20)
+#define B_AX_RDU_INT_EN			BIT(19)
+#define B_AX_RXDMA_STUCK_INT_EN		BIT(18)
+#define B_AX_TXDMA_STUCK_INT_EN		BIT(17)
+#define B_AX_PCIE_HOTRST_INT_EN		BIT(16)
+#define B_AX_PCIE_FLR_INT_EN		BIT(15)
+#define B_AX_PCIE_PERST_INT_EN		BIT(14)
+#define B_AX_TXDMA_CH12_INT_EN		BIT(13)
+#define B_AX_TXDMA_CH9_INT_EN		BIT(12)
+#define B_AX_TXDMA_CH8_INT_EN		BIT(11)
+#define B_AX_TXDMA_ACH7_INT_EN		BIT(10)
+#define B_AX_TXDMA_ACH6_INT_EN		BIT(9)
+#define B_AX_TXDMA_ACH5_INT_EN		BIT(8)
+#define B_AX_TXDMA_ACH4_INT_EN		BIT(7)
+#define B_AX_TXDMA_ACH3_INT_EN		BIT(6)
+#define B_AX_TXDMA_ACH2_INT_EN		BIT(5)
+#define B_AX_TXDMA_ACH1_INT_EN		BIT(4)
+#define B_AX_TXDMA_ACH0_INT_EN		BIT(3)
+#define B_AX_RPQDMA_INT_EN		BIT(2)
+#define B_AX_RXP1DMA_INT_EN		BIT(1)
+#define B_AX_RXDMA_INT_EN		BIT(0)
+
+#define R_AX_PCIE_HISR00	0x10B4
+#define B_AX_HC00ISR_IND_INT		BIT(27)
+#define B_AX_HD1ISR_IND_INT		BIT(26)
+#define B_AX_HD0ISR_IND_INT		BIT(25)
+#define B_AX_HS0ISR_IND_INT		BIT(24)
+#define B_AX_RETRAIN_INT		BIT(21)
+#define B_AX_RPQBD_FULL_INT		BIT(20)
+#define B_AX_RDU_INT			BIT(19)
+#define B_AX_RXDMA_STUCK_INT		BIT(18)
+#define B_AX_TXDMA_STUCK_INT		BIT(17)
+#define B_AX_PCIE_HOTRST_INT		BIT(16)
+#define B_AX_PCIE_FLR_INT		BIT(15)
+#define B_AX_PCIE_PERST_INT		BIT(14)
+#define B_AX_TXDMA_CH12_INT		BIT(13)
+#define B_AX_TXDMA_CH9_INT		BIT(12)
+#define B_AX_TXDMA_CH8_INT		BIT(11)
+#define B_AX_TXDMA_ACH7_INT		BIT(10)
+#define B_AX_TXDMA_ACH6_INT		BIT(9)
+#define B_AX_TXDMA_ACH5_INT		BIT(8)
+#define B_AX_TXDMA_ACH4_INT		BIT(7)
+#define B_AX_TXDMA_ACH3_INT		BIT(6)
+#define B_AX_TXDMA_ACH2_INT		BIT(5)
+#define B_AX_TXDMA_ACH1_INT		BIT(4)
+#define B_AX_TXDMA_ACH0_INT		BIT(3)
+#define B_AX_RPQDMA_INT			BIT(2)
+#define B_AX_RXP1DMA_INT		BIT(1)
+#define B_AX_RXDMA_INT			BIT(0)
+
+#define R_AX_PCIE_HIMR10	0x13B0
+#define B_AX_HC10ISR_IND_INT_EN		BIT(28)
+#define B_AX_TXDMA_CH11_INT_EN		BIT(12)
+#define B_AX_TXDMA_CH10_INT_EN		BIT(11)
+
+#define R_AX_PCIE_HISR10	0x13B4
+#define B_AX_HC10ISR_IND_INT		BIT(28)
+#define B_AX_TXDMA_CH11_INT		BIT(12)
+#define B_AX_TXDMA_CH10_INT		BIT(11)
+
+/* TX/RX */
+#define R_AX_RXQ_RXBD_IDX	0x1050
+#define R_AX_RPQ_RXBD_IDX	0x1054
+#define R_AX_ACH0_TXBD_IDX	0x1058
+#define R_AX_ACH1_TXBD_IDX	0x105C
+#define R_AX_ACH2_TXBD_IDX	0x1060
+#define R_AX_ACH3_TXBD_IDX	0x1064
+#define R_AX_ACH4_TXBD_IDX	0x1068
+#define R_AX_ACH5_TXBD_IDX	0x106C
+#define R_AX_ACH6_TXBD_IDX	0x1070
+#define R_AX_ACH7_TXBD_IDX	0x1074
+#define R_AX_CH8_TXBD_IDX	0x1078 /* Management Queue band 0 */
+#define R_AX_CH9_TXBD_IDX	0x107C /* HI Queue band 0 */
+#define R_AX_CH10_TXBD_IDX	0x137C /* Management Queue band 1 */
+#define R_AX_CH11_TXBD_IDX	0x1380 /* HI Queue band 1 */
+#define R_AX_CH12_TXBD_IDX	0x1080 /* FWCMD Queue */
+#define TXBD_HW_IDX_MASK	GENMASK(27, 16)
+#define TXBD_HOST_IDX_MASK	GENMASK(11, 0)
+
+#define R_AX_ACH0_TXBD_DESA_L	0x1110
+#define R_AX_ACH0_TXBD_DESA_H	0x1114
+#define R_AX_ACH1_TXBD_DESA_L	0x1118
+#define R_AX_ACH1_TXBD_DESA_H	0x111C
+#define R_AX_ACH2_TXBD_DESA_L	0x1120
+#define R_AX_ACH2_TXBD_DESA_H	0x1124
+#define R_AX_ACH3_TXBD_DESA_L	0x1128
+#define R_AX_ACH3_TXBD_DESA_H	0x112C
+#define R_AX_ACH4_TXBD_DESA_L	0x1130
+#define R_AX_ACH4_TXBD_DESA_H	0x1134
+#define R_AX_ACH5_TXBD_DESA_L	0x1138
+#define R_AX_ACH5_TXBD_DESA_H	0x113C
+#define R_AX_ACH6_TXBD_DESA_L	0x1140
+#define R_AX_ACH6_TXBD_DESA_H	0x1144
+#define R_AX_ACH7_TXBD_DESA_L	0x1148
+#define R_AX_ACH7_TXBD_DESA_H	0x114C
+#define R_AX_CH8_TXBD_DESA_L	0x1150
+#define R_AX_CH8_TXBD_DESA_H	0x1154
+#define R_AX_CH9_TXBD_DESA_L	0x1158
+#define R_AX_CH9_TXBD_DESA_H	0x115C
+#define R_AX_CH10_TXBD_DESA_L	0x1358
+#define R_AX_CH10_TXBD_DESA_H	0x135C
+#define R_AX_CH11_TXBD_DESA_L	0x1360
+#define R_AX_CH11_TXBD_DESA_H	0x1364
+#define R_AX_CH12_TXBD_DESA_L	0x1160
+#define R_AX_CH12_TXBD_DESA_H	0x1164
+#define R_AX_RXQ_RXBD_DESA_L	0x1100
+#define R_AX_RXQ_RXBD_DESA_H	0x1104
+#define R_AX_RPQ_RXBD_DESA_L	0x1108
+#define R_AX_RPQ_RXBD_DESA_H	0x110C
+#define B_AX_DESC_NUM_MSK		GENMASK(11, 0)
+
+#define R_AX_RXQ_RXBD_NUM	0x1020
+#define R_AX_RPQ_RXBD_NUM	0x1022
+#define R_AX_ACH0_TXBD_NUM	0x1024
+#define R_AX_ACH1_TXBD_NUM	0x1026
+#define R_AX_ACH2_TXBD_NUM	0x1028
+#define R_AX_ACH3_TXBD_NUM	0x102A
+#define R_AX_ACH4_TXBD_NUM	0x102C
+#define R_AX_ACH5_TXBD_NUM	0x102E
+#define R_AX_ACH6_TXBD_NUM	0x1030
+#define R_AX_ACH7_TXBD_NUM	0x1032
+#define R_AX_CH8_TXBD_NUM	0x1034
+#define R_AX_CH9_TXBD_NUM	0x1036
+#define R_AX_CH10_TXBD_NUM	0x1338
+#define R_AX_CH11_TXBD_NUM	0x133A
+#define R_AX_CH12_TXBD_NUM	0x1038
+
+#define R_AX_ACH0_BDRAM_CTRL	0x1200
+#define R_AX_ACH1_BDRAM_CTRL	0x1204
+#define R_AX_ACH2_BDRAM_CTRL	0x1208
+#define R_AX_ACH3_BDRAM_CTRL	0x120C
+#define R_AX_ACH4_BDRAM_CTRL	0x1210
+#define R_AX_ACH5_BDRAM_CTRL	0x1214
+#define R_AX_ACH6_BDRAM_CTRL	0x1218
+#define R_AX_ACH7_BDRAM_CTRL	0x121C
+#define R_AX_CH8_BDRAM_CTRL	0x1220
+#define R_AX_CH9_BDRAM_CTRL	0x1224
+#define R_AX_CH10_BDRAM_CTRL	0x1320
+#define R_AX_CH11_BDRAM_CTRL	0x1324
+#define R_AX_CH12_BDRAM_CTRL	0x1228
+#define BDRAM_SIDX_MASK		GENMASK(7, 0)
+#define BDRAM_MAX_MASK		GENMASK(15, 8)
+#define BDRAM_MIN_MASK		GENMASK(23, 16)
+
+#define R_AX_PCIE_INIT_CFG1	0x1000
+#define B_AX_PCIE_RXRST_KEEP_REG	BIT(23)
+#define B_AX_PCIE_TXRST_KEEP_REG	BIT(22)
+#define B_AX_PCIE_PERST_KEEP_REG	BIT(21)
+#define B_AX_PCIE_FLR_KEEP_REG		BIT(20)
+#define B_AX_PCIE_TRAIN_KEEP_REG	BIT(19)
+#define B_AX_RXBD_MODE			BIT(18)
+#define B_AX_PCIE_MAX_RXDMA_MASK	GENMASK(16, 14)
+#define B_AX_RXHCI_EN			BIT(13)
+#define B_AX_LATENCY_CONTROL		BIT(12)
+#define B_AX_TXHCI_EN			BIT(11)
+#define B_AX_PCIE_MAX_TXDMA_MASK	GENMASK(10, 8)
+#define B_AX_TX_TRUNC_MODE		BIT(5)
+#define B_AX_RX_TRUNC_MODE		BIT(4)
+#define B_AX_RST_BDRAM			BIT(3)
+#define B_AX_DIS_RXDMA_PRE		BIT(2)
+
+#define R_AX_TXDMA_ADDR_H	0x10F0
+#define R_AX_RXDMA_ADDR_H	0x10F4
+
+#define R_AX_PCIE_DMA_STOP1	0x1010
+#define B_AX_STOP_PCIEIO		BIT(20)
+#define B_AX_STOP_WPDMA			BIT(19)
+#define B_AX_STOP_CH12			BIT(18)
+#define B_AX_STOP_CH9			BIT(17)
+#define B_AX_STOP_CH8			BIT(16)
+#define B_AX_STOP_ACH7			BIT(15)
+#define B_AX_STOP_ACH6			BIT(14)
+#define B_AX_STOP_ACH5			BIT(13)
+#define B_AX_STOP_ACH4			BIT(12)
+#define B_AX_STOP_ACH3			BIT(11)
+#define B_AX_STOP_ACH2			BIT(10)
+#define B_AX_STOP_ACH1			BIT(9)
+#define B_AX_STOP_ACH0			BIT(8)
+#define B_AX_STOP_RPQ			BIT(1)
+#define B_AX_STOP_RXQ			BIT(0)
+#define B_AX_TX_STOP1_ALL		GENMASK(18, 8)
+
+#define R_AX_PCIE_DMA_STOP2	0x1310
+#define B_AX_STOP_CH11			BIT(1)
+#define B_AX_STOP_CH10			BIT(0)
+#define B_AX_TX_STOP2_ALL		GENMASK(1, 0)
+
+#define R_AX_TXBD_RWPTR_CLR1	0x1014
+#define B_AX_CLR_CH12_IDX		BIT(10)
+#define B_AX_CLR_CH9_IDX		BIT(9)
+#define B_AX_CLR_CH8_IDX		BIT(8)
+#define B_AX_CLR_ACH7_IDX		BIT(7)
+#define B_AX_CLR_ACH6_IDX		BIT(6)
+#define B_AX_CLR_ACH5_IDX		BIT(5)
+#define B_AX_CLR_ACH4_IDX		BIT(4)
+#define B_AX_CLR_ACH3_IDX		BIT(3)
+#define B_AX_CLR_ACH2_IDX		BIT(2)
+#define B_AX_CLR_ACH1_IDX		BIT(1)
+#define B_AX_CLR_ACH0_IDX		BIT(0)
+#define B_AX_TXBD_CLR1_ALL		GENMASK(10, 0)
+
+#define R_AX_RXBD_RWPTR_CLR	0x1018
+#define B_AX_CLR_RPQ_IDX		BIT(1)
+#define B_AX_CLR_RXQ_IDX		BIT(0)
+#define B_AX_RXBD_CLR_ALL		GENMASK(1, 0)
+
+#define R_AX_TXBD_RWPTR_CLR2	0x1314
+#define B_AX_CLR_CH11_IDX		BIT(1)
+#define B_AX_CLR_CH10_IDX		BIT(0)
+#define B_AX_TXBD_CLR2_ALL		GENMASK(1, 0)
+
+#define R_AX_PCIE_DMA_BUSY1	0x101C
+#define B_AX_PCIEIO_RX_BUSY		BIT(22)
+#define B_AX_PCIEIO_TX_BUSY		BIT(21)
+#define B_AX_PCIEIO_BUSY		BIT(20)
+#define B_AX_WPDMA_BUSY			BIT(19)
+
+#define R_AX_PCIE_DMA_BUSY2	0x131C
+#define B_AX_CH11_BUSY			BIT(1)
+#define B_AX_CH10_BUSY			BIT(0)
+
+/* Configure */
+#define R_AX_PCIE_INIT_CFG1	0x1000
+#define B_AX_PCIE_RXRST_KEEP_REG	BIT(23)
+#define B_AX_PCIE_TXRST_KEEP_REG	BIT(22)
+#define B_AX_DIS_RXDMA_PRE		BIT(2)
+
+#define R_AX_PCIE_INIT_CFG2		0x1004
+#define B_AX_WD_ITVL_IDLE		GENMASK(27, 24)
+#define B_AX_WD_ITVL_ACT		GENMASK(19, 16)
+
+#define R_AX_PCIE_PS_CTRL		0x1008
+#define B_AX_L1OFF_PWR_OFF_EN		BIT(5)
+
+#define R_AX_INT_MIT_RX			0x10D4
+#define B_AX_RXMIT_RXP2_SEL		BIT(19)
+#define B_AX_RXMIT_RXP1_SEL		BIT(18)
+#define B_AX_RXTIMER_UNIT_MASK		GENMASK(17, 16)
+#define AX_RXTIMER_UNIT_64US		0
+#define AX_RXTIMER_UNIT_128US		1
+#define AX_RXTIMER_UNIT_256US		2
+#define AX_RXTIMER_UNIT_512US		3
+#define B_AX_RXCOUNTER_MATCH_MASK	GENMASK(15, 8)
+#define B_AX_RXTIMER_MATCH_MASK		GENMASK(7, 0)
+
+#define R_AX_DBG_ERR_FLAG		0x11C4
+#define B_AX_PCIE_RPQ_FULL		BIT(29)
+#define B_AX_PCIE_RXQ_FULL		BIT(28)
+#define B_AX_CPL_STATUS_MASK		GENMASK(27, 25)
+#define B_AX_RX_STUCK			BIT(22)
+#define B_AX_TX_STUCK			BIT(21)
+#define B_AX_PCIEDBG_TXERR0		BIT(16)
+#define B_AX_PCIE_RXP1_ERR0		BIT(4)
+#define B_AX_PCIE_TXBD_LEN0		BIT(1)
+#define B_AX_PCIE_TXBD_4KBOUD_LENERR	BIT(0)
+
+#define R_AX_LBC_WATCHDOG		0x11D8
+#define B_AX_LBC_TIMER			GENMASK(7, 4)
+#define B_AX_LBC_FLAG			BIT(1)
+#define B_AX_LBC_EN			BIT(0)
+
+#define R_AX_PCIE_EXP_CTRL		0x13F0
+#define B_AX_EN_CHKDSC_NO_RX_STUCK	BIT(20)
+#define B_AX_MAX_TAG_NUM		GENMASK(18, 16)
+#define B_AX_SIC_EN_FORCE_CLKREQ	BIT(4)
+
+#define R_AX_PCIE_RX_PREF_ADV		0x13F4
+#define B_AX_RXDMA_PREF_ADV_EN		BIT(0)
+
+#define RTW89_PCI_TXBD_NUM_MAX		256
+#define RTW89_PCI_RXBD_NUM_MAX		256
+#define RTW89_PCI_TXWD_NUM_MAX		512
+#define RTW89_PCI_TXWD_PAGE_SIZE	128
+#define RTW89_PCI_ADDRINFO_MAX		4
+#define RTW89_PCI_RX_BUF_SIZE		11460
+
+#define RTW89_PCI_POLL_BDRAM_RST_CNT	100
+#define RTW89_PCI_MULTITAG		8
+
+/* PCIE CFG register */
+#define RTW89_PCIE_ASPM_CTRL		0x070F
+#define RTW89_L1DLY_MASK		GENMASK(5, 3)
+#define RTW89_L0DLY_MASK		GENMASK(2, 0)
+#define RTW89_PCIE_TIMER_CTRL		0x0718
+#define RTW89_PCIE_BIT_L1SUB		BIT(5)
+#define RTW89_PCIE_L1_CTRL		0x0719
+#define RTW89_PCIE_BIT_CLK		BIT(4)
+#define RTW89_PCIE_BIT_L1		BIT(3)
+#define RTW89_PCIE_CLK_CTRL		0x0725
+#define RTW89_PCIE_RST_MSTATE		0x0B48
+#define RTW89_PCIE_BIT_CFG_RST_MSTATE	BIT(0)
+#define RTW89_PCIE_PHY_RATE		0x82
+#define RTW89_PCIE_PHY_RATE_MASK	GENMASK(1, 0)
+#define INTF_INTGRA_MINREF_V1	90
+#define INTF_INTGRA_HOSTREF_V1	100
+
+enum rtw89_pcie_phy {
+	PCIE_PHY_GEN1,
+	PCIE_PHY_GEN2,
+	PCIE_PHY_GEN1_UNDEFINE = 0x7F,
+};
+
+enum mac_ax_func_sw {
+	MAC_AX_FUNC_DIS,
+	MAC_AX_FUNC_EN,
+};
+
+enum rtw89_pcie_l0sdly {
+	PCIE_L0SDLY_1US = 0,
+	PCIE_L0SDLY_2US = 1,
+	PCIE_L0SDLY_3US = 2,
+	PCIE_L0SDLY_4US = 3,
+	PCIE_L0SDLY_5US = 4,
+	PCIE_L0SDLY_6US = 5,
+	PCIE_L0SDLY_7US = 6,
+};
+
+enum rtw89_pcie_l1dly {
+	PCIE_L1DLY_16US = 4,
+	PCIE_L1DLY_32US = 5,
+	PCIE_L1DLY_64US = 6,
+	PCIE_L1DLY_HW_INFI = 7,
+};
+
+enum rtw89_pcie_clkdly_hw {
+	PCIE_CLKDLY_HW_0 = 0,
+	PCIE_CLKDLY_HW_30US = 0x1,
+	PCIE_CLKDLY_HW_50US = 0x2,
+	PCIE_CLKDLY_HW_100US = 0x3,
+	PCIE_CLKDLY_HW_150US = 0x4,
+	PCIE_CLKDLY_HW_200US = 0x5,
+};
+
+struct rtw89_pci_bd_ram {
+	u8 start_idx;
+	u8 max_num;
+	u8 min_num;
+};
+
+struct rtw89_pci_tx_data {
+	dma_addr_t dma;
+};
+
+struct rtw89_pci_rx_info {
+	dma_addr_t dma;
+	u32 fs:1, ls:1, tag:11, len:14;
+};
+
+#define RTW89_PCI_TXBD_OPTION_LS	BIT(14)
+
+struct rtw89_pci_tx_bd_32 {
+	__le16 length;
+	__le16 option;
+	__le32 dma;
+} __packed;
+
+#define RTW89_PCI_TXWP_VALID		BIT(15)
+
+struct rtw89_pci_tx_wp_info {
+	__le16 seq0;
+	__le16 seq1;
+	__le16 seq2;
+	__le16 seq3;
+} __packed;
+
+#define RTW89_PCI_ADDR_MSDU_LS		BIT(15)
+#define RTW89_PCI_ADDR_LS		BIT(14)
+#define RTW89_PCI_ADDR_HIGH(a)		(((a) << 6) & GENMASK(13, 6))
+#define RTW89_PCI_ADDR_NUM(x)		((x) & GENMASK(5, 0))
+
+struct rtw89_pci_tx_addr_info_32 {
+	__le16 length;
+	__le16 option;
+	__le32 dma;
+} __packed;
+
+#define RTW89_PCI_RPP_POLLUTED		BIT(31)
+#define RTW89_PCI_RPP_SEQ		GENMASK(30, 16)
+#define RTW89_PCI_RPP_TX_STATUS		GENMASK(15, 13)
+#define RTW89_TX_DONE			0x0
+#define RTW89_TX_RETRY_LIMIT		0x1
+#define RTW89_TX_LIFE_TIME		0x2
+#define RTW89_TX_MACID_DROP		0x3
+#define RTW89_PCI_RPP_QSEL		GENMASK(12, 8)
+#define RTW89_PCI_RPP_MACID		GENMASK(7, 0)
+
+struct rtw89_pci_rpp_fmt {
+	__le32 dword;
+} __packed;
+
+struct rtw89_pci_rx_bd_32 {
+	__le16 buf_size;
+	__le16 rsvd;
+	__le32 dma;
+} __packed;
+
+#define RTW89_PCI_RXBD_FS		BIT(15)
+#define RTW89_PCI_RXBD_LS		BIT(14)
+#define RTW89_PCI_RXBD_WRITE_SIZE	GENMASK(13, 0)
+#define RTW89_PCI_RXBD_TAG		GENMASK(28, 16)
+
+struct rtw89_pci_rxbd_info {
+	__le32 dword;
+};
+
+struct rtw89_pci_tx_wd {
+	struct list_head list;
+	struct sk_buff_head queue;
+
+	void *vaddr;
+	dma_addr_t paddr;
+	u32 len;
+	u32 seq;
+};
+
+struct rtw89_pci_dma_ring {
+	void *head;
+	u8 desc_size;
+	dma_addr_t dma;
+
+	u32 addr_num;
+	u32 addr_idx;
+	u32 addr_bdram;
+	u32 addr_desa_l;
+	u32 addr_desa_h;
+
+	u32 len;
+	u32 wp; /* host idx */
+	u32 rp; /* hw idx */
+};
+
+struct rtw89_pci_tx_wd_ring {
+	void *head;
+	dma_addr_t dma;
+
+	struct rtw89_pci_tx_wd pages[RTW89_PCI_TXWD_NUM_MAX];
+	struct list_head free_pages;
+
+	u32 page_size;
+	u32 page_num;
+	u32 curr_num;
+};
+
+#define RTW89_RX_TAG_MAX		0x1fff
+
+struct rtw89_pci_tx_ring {
+	struct rtw89_pci_tx_wd_ring wd_ring;
+	struct rtw89_pci_dma_ring bd_ring;
+	struct list_head busy_pages;
+	u8 txch;
+	bool dma_enabled;
+	u16 tag; /* range from 0x0001 ~ 0x1fff */
+
+	u64 tx_cnt;
+	u64 tx_acked;
+	u64 tx_retry_lmt;
+	u64 tx_life_time;
+	u64 tx_mac_id_drop;
+};
+
+struct rtw89_pci_rx_ring {
+	struct rtw89_pci_dma_ring bd_ring;
+	struct sk_buff *buf[RTW89_PCI_RXBD_NUM_MAX];
+	u32 buf_sz;
+	struct sk_buff *diliver_skb;
+	struct rtw89_rx_desc_info diliver_desc;
+};
+
+struct rtw89_pci_isrs {
+	u32 halt_c2h_isrs;
+	u32 isrs[2];
+};
+
+struct rtw89_pci {
+	struct pci_dev *pdev;
+
+	/* protect HW irq related registers */
+	spinlock_t irq_lock;
+	/* protect TRX resources (exclude RXQ) */
+	spinlock_t trx_lock;
+	bool running;
+	struct rtw89_pci_tx_ring tx_rings[RTW89_TXCH_NUM];
+	struct rtw89_pci_rx_ring rx_rings[RTW89_RXCH_NUM];
+	struct sk_buff_head h2c_queue;
+	struct sk_buff_head h2c_release_queue;
+
+	u32 halt_c2h_intrs;
+	u32 intrs[2];
+	void __iomem *mmap;
+};
+
+static inline struct rtw89_pci_rx_info *RTW89_PCI_RX_SKB_CB(struct sk_buff *skb)
+{
+	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+
+	BUILD_BUG_ON(sizeof(struct rtw89_pci_tx_data) >
+		     sizeof(info->status.status_driver_data));
+
+	return (struct rtw89_pci_rx_info *)skb->cb;
+}
+
+static inline struct rtw89_pci_rx_bd_32 *
+RTW89_PCI_RX_BD(struct rtw89_pci_rx_ring *rx_ring, u32 idx)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u8 *head = bd_ring->head;
+	u32 desc_size = bd_ring->desc_size;
+	u32 offset = idx * desc_size;
+
+	return (struct rtw89_pci_rx_bd_32 *)(head + offset);
+}
+
+static inline void
+rtw89_pci_rxbd_increase(struct rtw89_pci_rx_ring *rx_ring, u32 cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+
+	bd_ring->wp += cnt;
+
+	if (bd_ring->wp >= bd_ring->len)
+		bd_ring->wp -= bd_ring->len;
+}
+
+static inline struct rtw89_pci_tx_data *RTW89_PCI_TX_SKB_CB(struct sk_buff *skb)
+{
+	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+
+	return (struct rtw89_pci_tx_data *)info->status.status_driver_data;
+}
+
+static inline struct rtw89_pci_tx_bd_32 *
+rtw89_pci_get_next_txbd(struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	struct rtw89_pci_tx_bd_32 *tx_bd, *head;
+
+	head = bd_ring->head;
+	tx_bd = head + bd_ring->wp;
+
+	return tx_bd;
+}
+
+static inline struct rtw89_pci_tx_wd *
+rtw89_pci_dequeue_txwd(struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+
+	txwd = list_first_entry_or_null(&wd_ring->free_pages,
+					struct rtw89_pci_tx_wd, list);
+	if (!txwd)
+		return NULL;
+
+	list_del_init(&txwd->list);
+	txwd->len = 0;
+	wd_ring->curr_num--;
+
+	return txwd;
+}
+
+static inline void
+rtw89_pci_enqueue_txwd(struct rtw89_pci_tx_ring *tx_ring,
+		       struct rtw89_pci_tx_wd *txwd)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+
+	memset(txwd->vaddr, 0, wd_ring->page_size);
+	list_add_tail(&txwd->list, &wd_ring->free_pages);
+	wd_ring->curr_num++;
+}
+
+static inline bool rtw89_pci_ltr_is_err_reg_val(u32 val)
+{
+	return val == 0xffffffff || val == 0xeaeaeaea;
+}
+
+extern const struct dev_pm_ops rtw89_pm_ops;
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/phy.c
@@ -0,0 +1,2868 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "debug.h"
+#include "fw.h"
+#include "phy.h"
+#include "ps.h"
+#include "reg.h"
+#include "sar.h"
+#include "coex.h"
+
+static u16 get_max_amsdu_len(struct rtw89_dev *rtwdev,
+			     const struct rtw89_ra_report *report)
+{
+	const struct rate_info *txrate = &report->txrate;
+	u32 bit_rate = report->bit_rate;
+	u8 mcs;
+
+	/* lower than ofdm, do not aggregate */
+	if (bit_rate < 550)
+		return 1;
+
+	/* prevent hardware rate fallback to G mode rate */
+	if (txrate->flags & RATE_INFO_FLAGS_MCS)
+		mcs = txrate->mcs & 0x07;
+	else if (txrate->flags & (RATE_INFO_FLAGS_VHT_MCS | RATE_INFO_FLAGS_HE_MCS))
+		mcs = txrate->mcs;
+	else
+		mcs = 0;
+
+	if (mcs <= 2)
+		return 1;
+
+	/* lower than 20M vht 2ss mcs8, make it small */
+	if (bit_rate < 1800)
+		return 1200;
+
+	/* lower than 40M vht 2ss mcs9, make it medium */
+	if (bit_rate < 4000)
+		return 2600;
+
+	/* not yet 80M vht 2ss mcs8/9, make it twice regular packet size */
+	if (bit_rate < 7000)
+		return 3500;
+
+	return rtwdev->chip->max_amsdu_limit;
+}
+
+static u64 get_mcs_ra_mask(u16 mcs_map, u8 highest_mcs, u8 gap)
+{
+	u64 ra_mask = 0;
+	u8 mcs_cap;
+	int i, nss;
+
+	for (i = 0, nss = 12; i < 4; i++, mcs_map >>= 2, nss += 12) {
+		mcs_cap = mcs_map & 0x3;
+		switch (mcs_cap) {
+		case 2:
+			ra_mask |= GENMASK_ULL(highest_mcs, 0) << nss;
+			break;
+		case 1:
+			ra_mask |= GENMASK_ULL(highest_mcs - gap, 0) << nss;
+			break;
+		case 0:
+			ra_mask |= GENMASK_ULL(highest_mcs - gap * 2, 0) << nss;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return ra_mask;
+}
+
+static u64 get_he_ra_mask(struct ieee80211_sta *sta)
+{
+	struct ieee80211_sta_he_cap cap = sta->he_cap;
+	u16 mcs_map;
+
+	switch (sta->bandwidth) {
+	case IEEE80211_STA_RX_BW_160:
+		if (cap.he_cap_elem.phy_cap_info[0] &
+		    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)
+			mcs_map = le16_to_cpu(cap.he_mcs_nss_supp.rx_mcs_80p80);
+		else
+			mcs_map = le16_to_cpu(cap.he_mcs_nss_supp.rx_mcs_160);
+		break;
+	default:
+		mcs_map = le16_to_cpu(cap.he_mcs_nss_supp.rx_mcs_80);
+	}
+
+	/* MCS11, MCS9, MCS7 */
+	return get_mcs_ra_mask(mcs_map, 11, 2);
+}
+
+#define RA_FLOOR_TABLE_SIZE	7
+#define RA_FLOOR_UP_GAP		3
+static u64 rtw89_phy_ra_mask_rssi(struct rtw89_dev *rtwdev, u8 rssi,
+				  u8 ratr_state)
+{
+	u8 rssi_lv_t[RA_FLOOR_TABLE_SIZE] = {30, 44, 48, 52, 56, 60, 100};
+	u8 rssi_lv = 0;
+	u8 i;
+
+	rssi >>= 1;
+	for (i = 0; i < RA_FLOOR_TABLE_SIZE; i++) {
+		if (i >= ratr_state)
+			rssi_lv_t[i] += RA_FLOOR_UP_GAP;
+		if (rssi < rssi_lv_t[i]) {
+			rssi_lv = i;
+			break;
+		}
+	}
+	if (rssi_lv == 0)
+		return 0xffffffffffffffffULL;
+	else if (rssi_lv == 1)
+		return 0xfffffffffffffff0ULL;
+	else if (rssi_lv == 2)
+		return 0xffffffffffffffe0ULL;
+	else if (rssi_lv == 3)
+		return 0xffffffffffffffc0ULL;
+	else if (rssi_lv == 4)
+		return 0xffffffffffffff80ULL;
+	else if (rssi_lv >= 5)
+		return 0xffffffffffffff00ULL;
+
+	return 0xffffffffffffffffULL;
+}
+
+static u64 rtw89_phy_ra_mask_cfg(struct rtw89_dev *rtwdev, struct rtw89_sta *rtwsta)
+{
+	struct rtw89_hal *hal = &rtwdev->hal;
+	struct ieee80211_sta *sta = rtwsta_to_sta(rtwsta);
+	struct cfg80211_bitrate_mask *mask = &rtwsta->mask;
+	enum nl80211_band band;
+	u64 cfg_mask;
+
+	if (!rtwsta->use_cfg_mask)
+		return -1;
+
+	switch (hal->current_band_type) {
+	case RTW89_BAND_2G:
+		band = NL80211_BAND_2GHZ;
+		cfg_mask = u64_encode_bits(mask->control[NL80211_BAND_2GHZ].legacy,
+					   RA_MASK_CCK_RATES | RA_MASK_OFDM_RATES);
+		break;
+	case RTW89_BAND_5G:
+		band = NL80211_BAND_5GHZ;
+		cfg_mask = u64_encode_bits(mask->control[NL80211_BAND_5GHZ].legacy,
+					   RA_MASK_OFDM_RATES);
+		break;
+	default:
+		rtw89_warn(rtwdev, "unhandled band type %d\n", hal->current_band_type);
+		return -1;
+	}
+
+	if (sta->he_cap.has_he) {
+		cfg_mask |= u64_encode_bits(mask->control[band].he_mcs[0],
+					    RA_MASK_HE_1SS_RATES);
+		cfg_mask |= u64_encode_bits(mask->control[band].he_mcs[1],
+					    RA_MASK_HE_2SS_RATES);
+	} else if (sta->vht_cap.vht_supported) {
+		cfg_mask |= u64_encode_bits(mask->control[band].vht_mcs[0],
+					    RA_MASK_VHT_1SS_RATES);
+		cfg_mask |= u64_encode_bits(mask->control[band].vht_mcs[1],
+					    RA_MASK_VHT_2SS_RATES);
+	} else if (sta->ht_cap.ht_supported) {
+		cfg_mask |= u64_encode_bits(mask->control[band].ht_mcs[0],
+					    RA_MASK_HT_1SS_RATES);
+		cfg_mask |= u64_encode_bits(mask->control[band].ht_mcs[1],
+					    RA_MASK_HT_2SS_RATES);
+	}
+
+	return cfg_mask;
+}
+
+static const u64
+rtw89_ra_mask_ht_rates[4] = {RA_MASK_HT_1SS_RATES, RA_MASK_HT_2SS_RATES,
+			     RA_MASK_HT_3SS_RATES, RA_MASK_HT_4SS_RATES};
+static const u64
+rtw89_ra_mask_vht_rates[4] = {RA_MASK_VHT_1SS_RATES, RA_MASK_VHT_2SS_RATES,
+			      RA_MASK_VHT_3SS_RATES, RA_MASK_VHT_4SS_RATES};
+static const u64
+rtw89_ra_mask_he_rates[4] = {RA_MASK_HE_1SS_RATES, RA_MASK_HE_2SS_RATES,
+			     RA_MASK_HE_3SS_RATES, RA_MASK_HE_4SS_RATES};
+
+static void rtw89_phy_ra_sta_update(struct rtw89_dev *rtwdev,
+				    struct ieee80211_sta *sta, bool csi)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_vif *rtwvif = rtwsta->rtwvif;
+	struct rtw89_phy_rate_pattern *rate_pattern = &rtwvif->rate_pattern;
+	struct rtw89_ra_info *ra = &rtwsta->ra;
+	const u64 *high_rate_masks = rtw89_ra_mask_ht_rates;
+	u8 rssi = ewma_rssi_read(&rtwsta->avg_rssi);
+	u64 high_rate_mask = 0;
+	u64 ra_mask = 0;
+	u8 mode = 0;
+	u8 csi_mode = RTW89_RA_RPT_MODE_LEGACY;
+	u8 bw_mode = 0;
+	u8 stbc_en = 0;
+	u8 ldpc_en = 0;
+	u8 i;
+	bool sgi = false;
+
+	memset(ra, 0, sizeof(*ra));
+	/* Set the ra mask from sta's capability */
+	if (sta->he_cap.has_he) {
+		mode |= RTW89_RA_MODE_HE;
+		csi_mode = RTW89_RA_RPT_MODE_HE;
+		ra_mask |= get_he_ra_mask(sta);
+		high_rate_masks = rtw89_ra_mask_he_rates;
+		if (sta->he_cap.he_cap_elem.phy_cap_info[2] &
+		    IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ)
+			stbc_en = 1;
+		if (sta->he_cap.he_cap_elem.phy_cap_info[1] &
+		    IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD)
+			ldpc_en = 1;
+	} else if (sta->vht_cap.vht_supported) {
+		u16 mcs_map = le16_to_cpu(sta->vht_cap.vht_mcs.rx_mcs_map);
+
+		mode |= RTW89_RA_MODE_VHT;
+		csi_mode = RTW89_RA_RPT_MODE_VHT;
+		/* MCS9, MCS8, MCS7 */
+		ra_mask |= get_mcs_ra_mask(mcs_map, 9, 1);
+		high_rate_masks = rtw89_ra_mask_vht_rates;
+		if (sta->vht_cap.cap & IEEE80211_VHT_CAP_RXSTBC_MASK)
+			stbc_en = 1;
+		if (sta->vht_cap.cap & IEEE80211_VHT_CAP_RXLDPC)
+			ldpc_en = 1;
+	} else if (sta->ht_cap.ht_supported) {
+		mode |= RTW89_RA_MODE_HT;
+		csi_mode = RTW89_RA_RPT_MODE_HT;
+		ra_mask |= ((u64)sta->ht_cap.mcs.rx_mask[3] << 48) |
+			   ((u64)sta->ht_cap.mcs.rx_mask[2] << 36) |
+			   (sta->ht_cap.mcs.rx_mask[1] << 24) |
+			   (sta->ht_cap.mcs.rx_mask[0] << 12);
+		high_rate_masks = rtw89_ra_mask_ht_rates;
+		if (sta->ht_cap.cap & IEEE80211_HT_CAP_RX_STBC)
+			stbc_en = 1;
+		if (sta->ht_cap.cap & IEEE80211_HT_CAP_LDPC_CODING)
+			ldpc_en = 1;
+	}
+
+	if (rtwdev->hal.current_band_type == RTW89_BAND_2G) {
+		if (sta->supp_rates[NL80211_BAND_2GHZ] <= 0xf)
+			mode |= RTW89_RA_MODE_CCK;
+		else
+			mode |= RTW89_RA_MODE_CCK | RTW89_RA_MODE_OFDM;
+	} else {
+		mode |= RTW89_RA_MODE_OFDM;
+	}
+
+	if (mode >= RTW89_RA_MODE_HT) {
+		for (i = 0; i < rtwdev->hal.tx_nss; i++)
+			high_rate_mask |= high_rate_masks[i];
+		ra_mask &= high_rate_mask;
+		if (mode & RTW89_RA_MODE_OFDM)
+			ra_mask |= RA_MASK_SUBOFDM_RATES;
+		if (mode & RTW89_RA_MODE_CCK)
+			ra_mask |= RA_MASK_SUBCCK_RATES;
+	} else if (mode & RTW89_RA_MODE_OFDM) {
+		if (mode & RTW89_RA_MODE_CCK)
+			ra_mask |= RA_MASK_SUBCCK_RATES;
+		ra_mask |= RA_MASK_OFDM_RATES;
+	} else {
+		ra_mask = RA_MASK_CCK_RATES;
+	}
+
+	if (mode != RTW89_RA_MODE_CCK) {
+		ra_mask &= rtw89_phy_ra_mask_rssi(rtwdev, rssi, 0);
+		ra_mask &= rtw89_phy_ra_mask_cfg(rtwdev, rtwsta);
+	}
+
+	switch (sta->bandwidth) {
+	case IEEE80211_STA_RX_BW_80:
+		bw_mode = RTW89_CHANNEL_WIDTH_80;
+		sgi = sta->vht_cap.vht_supported &&
+		      (sta->vht_cap.cap & IEEE80211_VHT_CAP_SHORT_GI_80);
+		break;
+	case IEEE80211_STA_RX_BW_40:
+		bw_mode = RTW89_CHANNEL_WIDTH_40;
+		sgi = sta->ht_cap.ht_supported &&
+		      (sta->ht_cap.cap & IEEE80211_HT_CAP_SGI_40);
+		break;
+	default:
+		bw_mode = RTW89_CHANNEL_WIDTH_20;
+		sgi = sta->ht_cap.ht_supported &&
+		      (sta->ht_cap.cap & IEEE80211_HT_CAP_SGI_20);
+		break;
+	}
+
+	if (sta->he_cap.he_cap_elem.phy_cap_info[3] &
+	    IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_16_QAM)
+		ra->dcm_cap = 1;
+
+	if (rate_pattern->enable) {
+		ra_mask = rtw89_phy_ra_mask_cfg(rtwdev, rtwsta);
+		ra_mask &= rate_pattern->ra_mask;
+		mode = rate_pattern->ra_mode;
+	}
+
+	ra->bw_cap = bw_mode;
+	ra->mode_ctrl = mode;
+	ra->macid = rtwsta->mac_id;
+	ra->stbc_cap = stbc_en;
+	ra->ldpc_cap = ldpc_en;
+	ra->ss_num = min(sta->rx_nss, rtwdev->hal.tx_nss) - 1;
+	ra->en_sgi = sgi;
+	ra->ra_mask = ra_mask;
+
+	if (!csi)
+		return;
+
+	ra->fixed_csi_rate_en = false;
+	ra->ra_csi_rate_en = true;
+	ra->cr_tbl_sel = false;
+	ra->band_num = rtwvif->phy_idx;
+	ra->csi_bw = bw_mode;
+	ra->csi_gi_ltf = RTW89_GILTF_LGI_4XHE32;
+	ra->csi_mcs_ss_idx = 5;
+	ra->csi_mode = csi_mode;
+}
+
+void rtw89_phy_ra_updata_sta(struct rtw89_dev *rtwdev, struct ieee80211_sta *sta)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_ra_info *ra = &rtwsta->ra;
+
+	rtw89_phy_ra_sta_update(rtwdev, sta, false);
+	ra->upd_mask = 1;
+	rtw89_debug(rtwdev, RTW89_DBG_RA,
+		    "ra updat: macid = %d, bw = %d, nss = %d, gi = %d %d",
+		    ra->macid,
+		    ra->bw_cap,
+		    ra->ss_num,
+		    ra->en_sgi,
+		    ra->giltf);
+
+	rtw89_fw_h2c_ra(rtwdev, ra, false);
+}
+
+static bool __check_rate_pattern(struct rtw89_phy_rate_pattern *next,
+				 u16 rate_base, u64 ra_mask, u8 ra_mode,
+				 u32 rate_ctrl, u32 ctrl_skip, bool force)
+{
+	u8 n, c;
+
+	if (rate_ctrl == ctrl_skip)
+		return true;
+
+	n = hweight32(rate_ctrl);
+	if (n == 0)
+		return true;
+
+	if (force && n != 1)
+		return false;
+
+	if (next->enable)
+		return false;
+
+	c = __fls(rate_ctrl);
+	next->rate = rate_base + c;
+	next->ra_mode = ra_mode;
+	next->ra_mask = ra_mask;
+	next->enable = true;
+
+	return true;
+}
+
+void rtw89_phy_rate_pattern_vif(struct rtw89_dev *rtwdev,
+				struct ieee80211_vif *vif,
+				const struct cfg80211_bitrate_mask *mask)
+{
+	struct ieee80211_supported_band *sband;
+	struct rtw89_vif *rtwvif = (struct rtw89_vif *)vif->drv_priv;
+	struct rtw89_phy_rate_pattern next_pattern = {0};
+	static const u16 hw_rate_he[] = {RTW89_HW_RATE_HE_NSS1_MCS0,
+					 RTW89_HW_RATE_HE_NSS2_MCS0,
+					 RTW89_HW_RATE_HE_NSS3_MCS0,
+					 RTW89_HW_RATE_HE_NSS4_MCS0};
+	static const u16 hw_rate_vht[] = {RTW89_HW_RATE_VHT_NSS1_MCS0,
+					  RTW89_HW_RATE_VHT_NSS2_MCS0,
+					  RTW89_HW_RATE_VHT_NSS3_MCS0,
+					  RTW89_HW_RATE_VHT_NSS4_MCS0};
+	static const u16 hw_rate_ht[] = {RTW89_HW_RATE_MCS0,
+					 RTW89_HW_RATE_MCS8,
+					 RTW89_HW_RATE_MCS16,
+					 RTW89_HW_RATE_MCS24};
+	u8 band = rtwdev->hal.current_band_type;
+	u8 tx_nss = rtwdev->hal.tx_nss;
+	u8 i;
+
+	for (i = 0; i < tx_nss; i++)
+		if (!__check_rate_pattern(&next_pattern, hw_rate_he[i],
+					  RA_MASK_HE_RATES, RTW89_RA_MODE_HE,
+					  mask->control[band].he_mcs[i],
+					  0, true))
+			goto out;
+
+	for (i = 0; i < tx_nss; i++)
+		if (!__check_rate_pattern(&next_pattern, hw_rate_vht[i],
+					  RA_MASK_VHT_RATES, RTW89_RA_MODE_VHT,
+					  mask->control[band].vht_mcs[i],
+					  0, true))
+			goto out;
+
+	for (i = 0; i < tx_nss; i++)
+		if (!__check_rate_pattern(&next_pattern, hw_rate_ht[i],
+					  RA_MASK_HT_RATES, RTW89_RA_MODE_HT,
+					  mask->control[band].ht_mcs[i],
+					  0, true))
+			goto out;
+
+	/* lagacy cannot be empty for nl80211_parse_tx_bitrate_mask, and
+	 * require at least one basic rate for ieee80211_set_bitrate_mask,
+	 * so the decision just depends on if all bitrates are set or not.
+	 */
+	sband = rtwdev->hw->wiphy->bands[band];
+	if (band == RTW89_BAND_2G) {
+		if (!__check_rate_pattern(&next_pattern, RTW89_HW_RATE_CCK1,
+					  RA_MASK_CCK_RATES | RA_MASK_OFDM_RATES,
+					  RTW89_RA_MODE_CCK | RTW89_RA_MODE_OFDM,
+					  mask->control[band].legacy,
+					  BIT(sband->n_bitrates) - 1, false))
+			goto out;
+	} else {
+		if (!__check_rate_pattern(&next_pattern, RTW89_HW_RATE_OFDM6,
+					  RA_MASK_OFDM_RATES, RTW89_RA_MODE_OFDM,
+					  mask->control[band].legacy,
+					  BIT(sband->n_bitrates) - 1, false))
+			goto out;
+	}
+
+	if (!next_pattern.enable)
+		goto out;
+
+	rtwvif->rate_pattern = next_pattern;
+	rtw89_debug(rtwdev, RTW89_DBG_RA,
+		    "configure pattern: rate 0x%x, mask 0x%llx, mode 0x%x\n",
+		    next_pattern.rate,
+		    next_pattern.ra_mask,
+		    next_pattern.ra_mode);
+	return;
+
+out:
+	rtwvif->rate_pattern.enable = false;
+	rtw89_debug(rtwdev, RTW89_DBG_RA, "unset rate pattern\n");
+}
+
+static void rtw89_phy_ra_updata_sta_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_dev *rtwdev = (struct rtw89_dev *)data;
+
+	rtw89_phy_ra_updata_sta(rtwdev, sta);
+}
+
+void rtw89_phy_ra_update(struct rtw89_dev *rtwdev)
+{
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_phy_ra_updata_sta_iter,
+					  rtwdev);
+}
+
+void rtw89_phy_ra_assoc(struct rtw89_dev *rtwdev, struct ieee80211_sta *sta)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_ra_info *ra = &rtwsta->ra;
+	u8 rssi = ewma_rssi_read(&rtwsta->avg_rssi) >> RSSI_FACTOR;
+	bool csi = rtw89_sta_has_beamformer_cap(sta);
+
+	rtw89_phy_ra_sta_update(rtwdev, sta, csi);
+
+	if (rssi > 40)
+		ra->init_rate_lv = 1;
+	else if (rssi > 20)
+		ra->init_rate_lv = 2;
+	else if (rssi > 1)
+		ra->init_rate_lv = 3;
+	else
+		ra->init_rate_lv = 0;
+	ra->upd_all = 1;
+	rtw89_debug(rtwdev, RTW89_DBG_RA,
+		    "ra assoc: macid = %d, mode = %d, bw = %d, nss = %d, lv = %d",
+		    ra->macid,
+		    ra->mode_ctrl,
+		    ra->bw_cap,
+		    ra->ss_num,
+		    ra->init_rate_lv);
+	rtw89_debug(rtwdev, RTW89_DBG_RA,
+		    "ra assoc: dcm = %d, er = %d, ldpc = %d, stbc = %d, gi = %d %d",
+		    ra->dcm_cap,
+		    ra->er_cap,
+		    ra->ldpc_cap,
+		    ra->stbc_cap,
+		    ra->en_sgi,
+		    ra->giltf);
+
+	rtw89_fw_h2c_ra(rtwdev, ra, csi);
+}
+
+u8 rtw89_phy_get_txsc(struct rtw89_dev *rtwdev,
+		      struct rtw89_channel_params *param,
+		      enum rtw89_bandwidth dbw)
+{
+	enum rtw89_bandwidth cbw = param->bandwidth;
+	u8 pri_ch = param->primary_chan;
+	u8 central_ch = param->center_chan;
+	u8 txsc_idx = 0;
+	u8 tmp = 0;
+
+	if (cbw == dbw || cbw == RTW89_CHANNEL_WIDTH_20)
+		return txsc_idx;
+
+	switch (cbw) {
+	case RTW89_CHANNEL_WIDTH_40:
+		txsc_idx = pri_ch > central_ch ? 1 : 2;
+		break;
+	case RTW89_CHANNEL_WIDTH_80:
+		if (dbw == RTW89_CHANNEL_WIDTH_20) {
+			if (pri_ch > central_ch)
+				txsc_idx = (pri_ch - central_ch) >> 1;
+			else
+				txsc_idx = ((central_ch - pri_ch) >> 1) + 1;
+		} else {
+			txsc_idx = pri_ch > central_ch ? 9 : 10;
+		}
+		break;
+	case RTW89_CHANNEL_WIDTH_160:
+		if (pri_ch > central_ch)
+			tmp = (pri_ch - central_ch) >> 1;
+		else
+			tmp = ((central_ch - pri_ch) >> 1) + 1;
+
+		if (dbw == RTW89_CHANNEL_WIDTH_20) {
+			txsc_idx = tmp;
+		} else if (dbw == RTW89_CHANNEL_WIDTH_40) {
+			if (tmp == 1 || tmp == 3)
+				txsc_idx = 9;
+			else if (tmp == 5 || tmp == 7)
+				txsc_idx = 11;
+			else if (tmp == 2 || tmp == 4)
+				txsc_idx = 10;
+			else if (tmp == 6 || tmp == 8)
+				txsc_idx = 12;
+			else
+				return 0xff;
+		} else {
+			txsc_idx = pri_ch > central_ch ? 13 : 14;
+		}
+		break;
+	case RTW89_CHANNEL_WIDTH_80_80:
+		if (dbw == RTW89_CHANNEL_WIDTH_20) {
+			if (pri_ch > central_ch)
+				txsc_idx = (10 - (pri_ch - central_ch)) >> 1;
+			else
+				txsc_idx = ((central_ch - pri_ch) >> 1) + 5;
+		} else if (dbw == RTW89_CHANNEL_WIDTH_40) {
+			txsc_idx = pri_ch > central_ch ? 10 : 12;
+		} else {
+			txsc_idx = 14;
+		}
+		break;
+	default:
+		break;
+	}
+
+	return txsc_idx;
+}
+
+u32 rtw89_phy_read_rf(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+		      u32 addr, u32 mask)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const u32 *base_addr = chip->rf_base_addr;
+	u32 val, direct_addr;
+
+	if (rf_path >= rtwdev->chip->rf_path_num) {
+		rtw89_err(rtwdev, "unsupported rf path (%d)\n", rf_path);
+		return INV_RF_DATA;
+	}
+
+	addr &= 0xff;
+	direct_addr = base_addr[rf_path] + (addr << 2);
+	mask &= RFREG_MASK;
+
+	val = rtw89_phy_read32_mask(rtwdev, direct_addr, mask);
+
+	return val;
+}
+EXPORT_SYMBOL(rtw89_phy_read_rf);
+
+bool rtw89_phy_write_rf(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+			u32 addr, u32 mask, u32 data)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const u32 *base_addr = chip->rf_base_addr;
+	u32 direct_addr;
+
+	if (rf_path >= rtwdev->chip->rf_path_num) {
+		rtw89_err(rtwdev, "unsupported rf path (%d)\n", rf_path);
+		return false;
+	}
+
+	addr &= 0xff;
+	direct_addr = base_addr[rf_path] + (addr << 2);
+	mask &= RFREG_MASK;
+
+	rtw89_phy_write32_mask(rtwdev, direct_addr, mask, data);
+
+	/* delay to ensure writing properly */
+	udelay(1);
+
+	return true;
+}
+EXPORT_SYMBOL(rtw89_phy_write_rf);
+
+static void rtw89_phy_bb_reset(struct rtw89_dev *rtwdev,
+			       enum rtw89_phy_idx phy_idx)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	chip->ops->bb_reset(rtwdev, phy_idx);
+}
+
+static void rtw89_phy_config_bb_reg(struct rtw89_dev *rtwdev,
+				    const struct rtw89_reg2_def *reg,
+				    enum rtw89_rf_path rf_path,
+				    void *extra_data)
+{
+	if (reg->addr == 0xfe)
+		mdelay(50);
+	else if (reg->addr == 0xfd)
+		mdelay(5);
+	else if (reg->addr == 0xfc)
+		mdelay(1);
+	else if (reg->addr == 0xfb)
+		udelay(50);
+	else if (reg->addr == 0xfa)
+		udelay(5);
+	else if (reg->addr == 0xf9)
+		udelay(1);
+	else
+		rtw89_phy_write32(rtwdev, reg->addr, reg->data);
+}
+
+static void
+rtw89_phy_cofig_rf_reg_store(struct rtw89_dev *rtwdev,
+			     const struct rtw89_reg2_def *reg,
+			     enum rtw89_rf_path rf_path,
+			     struct rtw89_fw_h2c_rf_reg_info *info)
+{
+	u16 idx = info->curr_idx % RTW89_H2C_RF_PAGE_SIZE;
+	u8 page = info->curr_idx / RTW89_H2C_RF_PAGE_SIZE;
+
+	info->rtw89_phy_config_rf_h2c[page][idx] =
+		cpu_to_le32((reg->addr << 20) | reg->data);
+	info->curr_idx++;
+}
+
+static int rtw89_phy_config_rf_reg_fw(struct rtw89_dev *rtwdev,
+				      struct rtw89_fw_h2c_rf_reg_info *info)
+{
+	u16 page = info->curr_idx / RTW89_H2C_RF_PAGE_SIZE;
+	u16 len = (info->curr_idx % RTW89_H2C_RF_PAGE_SIZE) * 4;
+	u8 i;
+	int ret = 0;
+
+	if (page > RTW89_H2C_RF_PAGE_NUM) {
+		rtw89_warn(rtwdev,
+			   "rf reg h2c total page num %d larger than %d (RTW89_H2C_RF_PAGE_NUM)\n",
+			   page, RTW89_H2C_RF_PAGE_NUM);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < page; i++) {
+		ret = rtw89_fw_h2c_rf_reg(rtwdev, info,
+					  RTW89_H2C_RF_PAGE_SIZE * 4, i);
+		if (ret)
+			return ret;
+	}
+	ret = rtw89_fw_h2c_rf_reg(rtwdev, info, len, i);
+	if (ret)
+		return ret;
+	info->curr_idx = 0;
+
+	return 0;
+}
+
+static void rtw89_phy_config_rf_reg(struct rtw89_dev *rtwdev,
+				    const struct rtw89_reg2_def *reg,
+				    enum rtw89_rf_path rf_path,
+				    void *extra_data)
+{
+	if (reg->addr == 0xfe) {
+		mdelay(50);
+	} else if (reg->addr == 0xfd) {
+		mdelay(5);
+	} else if (reg->addr == 0xfc) {
+		mdelay(1);
+	} else if (reg->addr == 0xfb) {
+		udelay(50);
+	} else if (reg->addr == 0xfa) {
+		udelay(5);
+	} else if (reg->addr == 0xf9) {
+		udelay(1);
+	} else {
+		rtw89_write_rf(rtwdev, rf_path, reg->addr, 0xfffff, reg->data);
+		rtw89_phy_cofig_rf_reg_store(rtwdev, reg, rf_path,
+					     (struct rtw89_fw_h2c_rf_reg_info *)extra_data);
+	}
+}
+
+static int rtw89_phy_sel_headline(struct rtw89_dev *rtwdev,
+				  const struct rtw89_phy_table *table,
+				  u32 *headline_size, u32 *headline_idx,
+				  u8 rfe, u8 cv)
+{
+	const struct rtw89_reg2_def *reg;
+	u32 headline;
+	u32 compare, target;
+	u8 rfe_para, cv_para;
+	u8 cv_max = 0;
+	bool case_matched = false;
+	u32 i;
+
+	for (i = 0; i < table->n_regs; i++) {
+		reg = &table->regs[i];
+		headline = get_phy_headline(reg->addr);
+		if (headline != PHY_HEADLINE_VALID)
+			break;
+	}
+	*headline_size = i;
+	if (*headline_size == 0)
+		return 0;
+
+	/* case 1: RFE match, CV match */
+	compare = get_phy_compare(rfe, cv);
+	for (i = 0; i < *headline_size; i++) {
+		reg = &table->regs[i];
+		target = get_phy_target(reg->addr);
+		if (target == compare) {
+			*headline_idx = i;
+			return 0;
+		}
+	}
+
+	/* case 2: RFE match, CV don't care */
+	compare = get_phy_compare(rfe, PHY_COND_DONT_CARE);
+	for (i = 0; i < *headline_size; i++) {
+		reg = &table->regs[i];
+		target = get_phy_target(reg->addr);
+		if (target == compare) {
+			*headline_idx = i;
+			return 0;
+		}
+	}
+
+	/* case 3: RFE match, CV max in table */
+	for (i = 0; i < *headline_size; i++) {
+		reg = &table->regs[i];
+		rfe_para = get_phy_cond_rfe(reg->addr);
+		cv_para = get_phy_cond_cv(reg->addr);
+		if (rfe_para == rfe) {
+			if (cv_para >= cv_max) {
+				cv_max = cv_para;
+				*headline_idx = i;
+				case_matched = true;
+			}
+		}
+	}
+
+	if (case_matched)
+		return 0;
+
+	/* case 4: RFE don't care, CV max in table */
+	for (i = 0; i < *headline_size; i++) {
+		reg = &table->regs[i];
+		rfe_para = get_phy_cond_rfe(reg->addr);
+		cv_para = get_phy_cond_cv(reg->addr);
+		if (rfe_para == PHY_COND_DONT_CARE) {
+			if (cv_para >= cv_max) {
+				cv_max = cv_para;
+				*headline_idx = i;
+				case_matched = true;
+			}
+		}
+	}
+
+	if (case_matched)
+		return 0;
+
+	return -EINVAL;
+}
+
+static void rtw89_phy_init_reg(struct rtw89_dev *rtwdev,
+			       const struct rtw89_phy_table *table,
+			       void (*config)(struct rtw89_dev *rtwdev,
+					      const struct rtw89_reg2_def *reg,
+					      enum rtw89_rf_path rf_path,
+					      void *data),
+			       void *extra_data)
+{
+	const struct rtw89_reg2_def *reg;
+	enum rtw89_rf_path rf_path = table->rf_path;
+	u8 rfe = rtwdev->efuse.rfe_type;
+	u8 cv = rtwdev->hal.cv;
+	u32 i;
+	u32 headline_size = 0, headline_idx = 0;
+	u32 target = 0, cfg_target;
+	u8 cond;
+	bool is_matched = true;
+	bool target_found = false;
+	int ret;
+
+	ret = rtw89_phy_sel_headline(rtwdev, table, &headline_size,
+				     &headline_idx, rfe, cv);
+	if (ret) {
+		rtw89_err(rtwdev, "invalid PHY package: %d/%d\n", rfe, cv);
+		return;
+	}
+
+	cfg_target = get_phy_target(table->regs[headline_idx].addr);
+	for (i = headline_size; i < table->n_regs; i++) {
+		reg = &table->regs[i];
+		cond = get_phy_cond(reg->addr);
+		switch (cond) {
+		case PHY_COND_BRANCH_IF:
+		case PHY_COND_BRANCH_ELIF:
+			target = get_phy_target(reg->addr);
+			break;
+		case PHY_COND_BRANCH_ELSE:
+			is_matched = false;
+			if (!target_found) {
+				rtw89_warn(rtwdev, "failed to load CR %x/%x\n",
+					   reg->addr, reg->data);
+				return;
+			}
+			break;
+		case PHY_COND_BRANCH_END:
+			is_matched = true;
+			target_found = false;
+			break;
+		case PHY_COND_CHECK:
+			if (target_found) {
+				is_matched = false;
+				break;
+			}
+
+			if (target == cfg_target) {
+				is_matched = true;
+				target_found = true;
+			} else {
+				is_matched = false;
+				target_found = false;
+			}
+			break;
+		default:
+			if (is_matched)
+				config(rtwdev, reg, rf_path, extra_data);
+			break;
+		}
+	}
+}
+
+void rtw89_phy_init_bb_reg(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const struct rtw89_phy_table *bb_table = chip->bb_table;
+
+	rtw89_phy_init_reg(rtwdev, bb_table, rtw89_phy_config_bb_reg, NULL);
+	rtw89_chip_init_txpwr_unit(rtwdev, RTW89_PHY_0);
+	rtw89_phy_bb_reset(rtwdev, RTW89_PHY_0);
+}
+
+static u32 rtw89_phy_nctl_poll(struct rtw89_dev *rtwdev)
+{
+	rtw89_phy_write32(rtwdev, 0x8080, 0x4);
+	udelay(1);
+	return rtw89_phy_read32(rtwdev, 0x8080);
+}
+
+void rtw89_phy_init_rf_reg(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const struct rtw89_phy_table *rf_table;
+	struct rtw89_fw_h2c_rf_reg_info *rf_reg_info;
+	u8 path;
+
+	rf_reg_info = kzalloc(sizeof(*rf_reg_info), GFP_KERNEL);
+	if (!rf_reg_info)
+		return;
+
+	for (path = RF_PATH_A; path < chip->rf_path_num; path++) {
+		rf_reg_info->rf_path = path;
+		rf_table = chip->rf_table[path];
+		rtw89_phy_init_reg(rtwdev, rf_table, rtw89_phy_config_rf_reg,
+				   (void *)rf_reg_info);
+		if (rtw89_phy_config_rf_reg_fw(rtwdev, rf_reg_info))
+			rtw89_warn(rtwdev, "rf path %d reg h2c config failed\n",
+				   path);
+	}
+	kfree(rf_reg_info);
+}
+
+static void rtw89_phy_init_rf_nctl(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const struct rtw89_phy_table *nctl_table;
+	u32 val;
+	int ret;
+
+	/* IQK/DPK clock & reset */
+	rtw89_phy_write32_set(rtwdev, 0x0c60, 0x3);
+	rtw89_phy_write32_set(rtwdev, 0x0c6c, 0x1);
+	rtw89_phy_write32_set(rtwdev, 0x58ac, 0x8000000);
+	rtw89_phy_write32_set(rtwdev, 0x78ac, 0x8000000);
+
+	/* check 0x8080 */
+	rtw89_phy_write32(rtwdev, 0x8000, 0x8);
+
+	ret = read_poll_timeout(rtw89_phy_nctl_poll, val, val == 0x4, 10,
+				1000, false, rtwdev);
+	if (ret)
+		rtw89_err(rtwdev, "failed to poll nctl block\n");
+
+	nctl_table = chip->nctl_table;
+	rtw89_phy_init_reg(rtwdev, nctl_table, rtw89_phy_config_bb_reg, NULL);
+}
+
+static u32 rtw89_phy0_phy1_offset(struct rtw89_dev *rtwdev, u32 addr)
+{
+	u32 phy_page = addr >> 8;
+	u32 ofst = 0;
+
+	switch (phy_page) {
+	case 0x6:
+	case 0x7:
+	case 0x8:
+	case 0x9:
+	case 0xa:
+	case 0xb:
+	case 0xc:
+	case 0xd:
+	case 0x19:
+	case 0x1a:
+	case 0x1b:
+		ofst = 0x2000;
+		break;
+	default:
+		/* warning case */
+		ofst = 0;
+		break;
+	}
+
+	if (phy_page >= 0x40 && phy_page <= 0x4f)
+		ofst = 0x2000;
+
+	return ofst;
+}
+
+void rtw89_phy_write32_idx(struct rtw89_dev *rtwdev, u32 addr, u32 mask,
+			   u32 data, enum rtw89_phy_idx phy_idx)
+{
+	if (rtwdev->dbcc_en && phy_idx == RTW89_PHY_1)
+		addr += rtw89_phy0_phy1_offset(rtwdev, addr);
+	rtw89_phy_write32_mask(rtwdev, addr, mask, data);
+}
+
+void rtw89_phy_set_phy_regs(struct rtw89_dev *rtwdev, u32 addr, u32 mask,
+			    u32 val)
+{
+	rtw89_phy_write32_idx(rtwdev, addr, mask, val, RTW89_PHY_0);
+
+	if (!rtwdev->dbcc_en)
+		return;
+
+	rtw89_phy_write32_idx(rtwdev, addr, mask, val, RTW89_PHY_1);
+}
+
+void rtw89_phy_write_reg3_tbl(struct rtw89_dev *rtwdev,
+			      const struct rtw89_phy_reg3_tbl *tbl)
+{
+	const struct rtw89_reg3_def *reg3;
+	int i;
+
+	for (i = 0; i < tbl->size; i++) {
+		reg3 = &tbl->reg3[i];
+		rtw89_phy_write32_mask(rtwdev, reg3->addr, reg3->mask, reg3->data);
+	}
+}
+
+const u8 rtw89_rs_idx_max[] = {
+	[RTW89_RS_CCK] = RTW89_RATE_CCK_MAX,
+	[RTW89_RS_OFDM] = RTW89_RATE_OFDM_MAX,
+	[RTW89_RS_MCS] = RTW89_RATE_MCS_MAX,
+	[RTW89_RS_HEDCM] = RTW89_RATE_HEDCM_MAX,
+	[RTW89_RS_OFFSET] = RTW89_RATE_OFFSET_MAX,
+};
+
+const u8 rtw89_rs_nss_max[] = {
+	[RTW89_RS_CCK] = 1,
+	[RTW89_RS_OFDM] = 1,
+	[RTW89_RS_MCS] = RTW89_NSS_MAX,
+	[RTW89_RS_HEDCM] = RTW89_NSS_HEDCM_MAX,
+	[RTW89_RS_OFFSET] = 1,
+};
+
+static const u8 _byr_of_rs[] = {
+	[RTW89_RS_CCK] = offsetof(struct rtw89_txpwr_byrate, cck),
+	[RTW89_RS_OFDM] = offsetof(struct rtw89_txpwr_byrate, ofdm),
+	[RTW89_RS_MCS] = offsetof(struct rtw89_txpwr_byrate, mcs),
+	[RTW89_RS_HEDCM] = offsetof(struct rtw89_txpwr_byrate, hedcm),
+	[RTW89_RS_OFFSET] = offsetof(struct rtw89_txpwr_byrate, offset),
+};
+
+#define _byr_seek(rs, raw) ((s8 *)(raw) + _byr_of_rs[rs])
+#define _byr_idx(rs, nss, idx) ((nss) * rtw89_rs_idx_max[rs] + (idx))
+#define _byr_chk(rs, nss, idx) \
+	((nss) < rtw89_rs_nss_max[rs] && (idx) < rtw89_rs_idx_max[rs])
+
+void rtw89_phy_load_txpwr_byrate(struct rtw89_dev *rtwdev,
+				 const struct rtw89_txpwr_table *tbl)
+{
+	const struct rtw89_txpwr_byrate_cfg *cfg = tbl->data;
+	const struct rtw89_txpwr_byrate_cfg *end = cfg + tbl->size;
+	s8 *byr;
+	u32 data;
+	u8 i, idx;
+
+	for (; cfg < end; cfg++) {
+		byr = _byr_seek(cfg->rs, &rtwdev->byr[cfg->band]);
+		data = cfg->data;
+
+		for (i = 0; i < cfg->len; i++, data >>= 8) {
+			idx = _byr_idx(cfg->rs, cfg->nss, (cfg->shf + i));
+			byr[idx] = (s8)(data & 0xff);
+		}
+	}
+}
+
+#define _phy_txpwr_rf_to_mac(rtwdev, txpwr_rf)				\
+({									\
+	const struct rtw89_chip_info *__c = (rtwdev)->chip;		\
+	(txpwr_rf) >> (__c->txpwr_factor_rf - __c->txpwr_factor_mac);	\
+})
+
+s8 rtw89_phy_read_txpwr_byrate(struct rtw89_dev *rtwdev,
+			       const struct rtw89_rate_desc *rate_desc)
+{
+	enum rtw89_band band = rtwdev->hal.current_band_type;
+	s8 *byr;
+	u8 idx;
+
+	if (rate_desc->rs == RTW89_RS_CCK)
+		band = RTW89_BAND_2G;
+
+	if (!_byr_chk(rate_desc->rs, rate_desc->nss, rate_desc->idx)) {
+		rtw89_debug(rtwdev, RTW89_DBG_TXPWR,
+			    "[TXPWR] unknown byrate desc rs=%d nss=%d idx=%d\n",
+			    rate_desc->rs, rate_desc->nss, rate_desc->idx);
+
+		return 0;
+	}
+
+	byr = _byr_seek(rate_desc->rs, &rtwdev->byr[band]);
+	idx = _byr_idx(rate_desc->rs, rate_desc->nss, rate_desc->idx);
+
+	return _phy_txpwr_rf_to_mac(rtwdev, byr[idx]);
+}
+
+static u8 rtw89_channel_to_idx(struct rtw89_dev *rtwdev, u8 channel)
+{
+	switch (channel) {
+	case 1 ... 14:
+		return channel - 1;
+	case 36 ... 64:
+		return (channel - 36) / 2;
+	case 100 ... 144:
+		return ((channel - 100) / 2) + 15;
+	case 149 ... 177:
+		return ((channel - 149) / 2) + 38;
+	default:
+		rtw89_warn(rtwdev, "unknown channel: %d\n", channel);
+		return 0;
+	}
+}
+
+s8 rtw89_phy_read_txpwr_limit(struct rtw89_dev *rtwdev,
+			      u8 bw, u8 ntx, u8 rs, u8 bf, u8 ch)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	u8 ch_idx = rtw89_channel_to_idx(rtwdev, ch);
+	u8 band = rtwdev->hal.current_band_type;
+	u8 regd = rtw89_regd_get(rtwdev, band);
+	s8 lmt = 0, sar;
+
+	switch (band) {
+	case RTW89_BAND_2G:
+		lmt = (*chip->txpwr_lmt_2g)[bw][ntx][rs][bf][regd][ch_idx];
+		break;
+	case RTW89_BAND_5G:
+		lmt = (*chip->txpwr_lmt_5g)[bw][ntx][rs][bf][regd][ch_idx];
+		break;
+	default:
+		rtw89_warn(rtwdev, "unknown band type: %d\n", band);
+		return 0;
+	}
+
+	lmt = _phy_txpwr_rf_to_mac(rtwdev, lmt);
+	sar = rtw89_query_sar(rtwdev);
+
+	return min(lmt, sar);
+}
+
+#define __fill_txpwr_limit_nonbf_bf(ptr, bw, ntx, rs, ch)		\
+	do {								\
+		u8 __i;							\
+		for (__i = 0; __i < RTW89_BF_NUM; __i++)		\
+			ptr[__i] = rtw89_phy_read_txpwr_limit(rtwdev,	\
+							      bw, ntx,	\
+							      rs, __i,	\
+							      (ch));	\
+	} while (0)
+
+static void rtw89_phy_fill_txpwr_limit_20m(struct rtw89_dev *rtwdev,
+					   struct rtw89_txpwr_limit *lmt,
+					   u8 ntx, u8 ch)
+{
+	__fill_txpwr_limit_nonbf_bf(lmt->cck_20m, RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_CCK, ch);
+	__fill_txpwr_limit_nonbf_bf(lmt->cck_40m, RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_CCK, ch);
+	__fill_txpwr_limit_nonbf_bf(lmt->ofdm, RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_OFDM, ch);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[0], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch);
+}
+
+static void rtw89_phy_fill_txpwr_limit_40m(struct rtw89_dev *rtwdev,
+					   struct rtw89_txpwr_limit *lmt,
+					   u8 ntx, u8 ch)
+{
+	__fill_txpwr_limit_nonbf_bf(lmt->cck_20m, RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_CCK, ch - 2);
+	__fill_txpwr_limit_nonbf_bf(lmt->cck_40m, RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_CCK, ch);
+	__fill_txpwr_limit_nonbf_bf(lmt->ofdm, RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_OFDM, ch - 2);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[0], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch - 2);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[1], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch + 2);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_40m[0], RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_MCS, ch);
+}
+
+static void rtw89_phy_fill_txpwr_limit_80m(struct rtw89_dev *rtwdev,
+					   struct rtw89_txpwr_limit *lmt,
+					   u8 ntx, u8 ch)
+{
+	s8 val_0p5_n[RTW89_BF_NUM];
+	s8 val_0p5_p[RTW89_BF_NUM];
+	u8 i;
+
+	__fill_txpwr_limit_nonbf_bf(lmt->ofdm, RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_OFDM, ch - 6);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[0], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch - 6);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[1], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch - 2);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[2], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch + 2);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_20m[3], RTW89_CHANNEL_WIDTH_20,
+				    ntx, RTW89_RS_MCS, ch + 6);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_40m[0], RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_MCS, ch - 4);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_40m[1], RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_MCS, ch + 4);
+	__fill_txpwr_limit_nonbf_bf(lmt->mcs_80m[0], RTW89_CHANNEL_WIDTH_80,
+				    ntx, RTW89_RS_MCS, ch);
+
+	__fill_txpwr_limit_nonbf_bf(val_0p5_n, RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_MCS, ch - 4);
+	__fill_txpwr_limit_nonbf_bf(val_0p5_p, RTW89_CHANNEL_WIDTH_40,
+				    ntx, RTW89_RS_MCS, ch + 4);
+
+	for (i = 0; i < RTW89_BF_NUM; i++)
+		lmt->mcs_40m_0p5[i] = min_t(s8, val_0p5_n[i], val_0p5_p[i]);
+}
+
+void rtw89_phy_fill_txpwr_limit(struct rtw89_dev *rtwdev,
+				struct rtw89_txpwr_limit *lmt,
+				u8 ntx)
+{
+	u8 ch = rtwdev->hal.current_channel;
+	u8 bw = rtwdev->hal.current_band_width;
+
+	memset(lmt, 0, sizeof(*lmt));
+
+	switch (bw) {
+	case RTW89_CHANNEL_WIDTH_20:
+		rtw89_phy_fill_txpwr_limit_20m(rtwdev, lmt, ntx, ch);
+		break;
+	case RTW89_CHANNEL_WIDTH_40:
+		rtw89_phy_fill_txpwr_limit_40m(rtwdev, lmt, ntx, ch);
+		break;
+	case RTW89_CHANNEL_WIDTH_80:
+		rtw89_phy_fill_txpwr_limit_80m(rtwdev, lmt, ntx, ch);
+		break;
+	}
+}
+
+static s8 rtw89_phy_read_txpwr_limit_ru(struct rtw89_dev *rtwdev,
+					u8 ru, u8 ntx, u8 ch)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	u8 ch_idx = rtw89_channel_to_idx(rtwdev, ch);
+	u8 band = rtwdev->hal.current_band_type;
+	u8 regd = rtw89_regd_get(rtwdev, band);
+	s8 lmt_ru = 0, sar;
+
+	switch (band) {
+	case RTW89_BAND_2G:
+		lmt_ru = (*chip->txpwr_lmt_ru_2g)[ru][ntx][regd][ch_idx];
+		break;
+	case RTW89_BAND_5G:
+		lmt_ru = (*chip->txpwr_lmt_ru_5g)[ru][ntx][regd][ch_idx];
+		break;
+	default:
+		rtw89_warn(rtwdev, "unknown band type: %d\n", band);
+		return 0;
+	}
+
+	lmt_ru = _phy_txpwr_rf_to_mac(rtwdev, lmt_ru);
+	sar = rtw89_query_sar(rtwdev);
+
+	return min(lmt_ru, sar);
+}
+
+static void
+rtw89_phy_fill_txpwr_limit_ru_20m(struct rtw89_dev *rtwdev,
+				  struct rtw89_txpwr_limit_ru *lmt_ru,
+				  u8 ntx, u8 ch)
+{
+	lmt_ru->ru26[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch);
+	lmt_ru->ru52[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch);
+	lmt_ru->ru106[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch);
+}
+
+static void
+rtw89_phy_fill_txpwr_limit_ru_40m(struct rtw89_dev *rtwdev,
+				  struct rtw89_txpwr_limit_ru *lmt_ru,
+				  u8 ntx, u8 ch)
+{
+	lmt_ru->ru26[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch - 2);
+	lmt_ru->ru26[1] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch + 2);
+	lmt_ru->ru52[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch - 2);
+	lmt_ru->ru52[1] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch + 2);
+	lmt_ru->ru106[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch - 2);
+	lmt_ru->ru106[1] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch + 2);
+}
+
+static void
+rtw89_phy_fill_txpwr_limit_ru_80m(struct rtw89_dev *rtwdev,
+				  struct rtw89_txpwr_limit_ru *lmt_ru,
+				  u8 ntx, u8 ch)
+{
+	lmt_ru->ru26[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch - 6);
+	lmt_ru->ru26[1] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch - 2);
+	lmt_ru->ru26[2] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch + 2);
+	lmt_ru->ru26[3] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU26,
+							ntx, ch + 6);
+	lmt_ru->ru52[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch - 6);
+	lmt_ru->ru52[1] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch - 2);
+	lmt_ru->ru52[2] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch + 2);
+	lmt_ru->ru52[3] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU52,
+							ntx, ch + 6);
+	lmt_ru->ru106[0] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch - 6);
+	lmt_ru->ru106[1] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch - 2);
+	lmt_ru->ru106[2] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch + 2);
+	lmt_ru->ru106[3] = rtw89_phy_read_txpwr_limit_ru(rtwdev, RTW89_RU106,
+							 ntx, ch + 6);
+}
+
+void rtw89_phy_fill_txpwr_limit_ru(struct rtw89_dev *rtwdev,
+				   struct rtw89_txpwr_limit_ru *lmt_ru,
+				   u8 ntx)
+{
+	u8 ch = rtwdev->hal.current_channel;
+	u8 bw = rtwdev->hal.current_band_width;
+
+	memset(lmt_ru, 0, sizeof(*lmt_ru));
+
+	switch (bw) {
+	case RTW89_CHANNEL_WIDTH_20:
+		rtw89_phy_fill_txpwr_limit_ru_20m(rtwdev, lmt_ru, ntx, ch);
+		break;
+	case RTW89_CHANNEL_WIDTH_40:
+		rtw89_phy_fill_txpwr_limit_ru_40m(rtwdev, lmt_ru, ntx, ch);
+		break;
+	case RTW89_CHANNEL_WIDTH_80:
+		rtw89_phy_fill_txpwr_limit_ru_80m(rtwdev, lmt_ru, ntx, ch);
+		break;
+	}
+}
+
+struct rtw89_phy_iter_ra_data {
+	struct rtw89_dev *rtwdev;
+	struct sk_buff *c2h;
+};
+
+static void rtw89_phy_c2h_ra_rpt_iter(void *data, struct ieee80211_sta *sta)
+{
+	struct rtw89_phy_iter_ra_data *ra_data = (struct rtw89_phy_iter_ra_data *)data;
+	struct rtw89_dev *rtwdev = ra_data->rtwdev;
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_ra_report *ra_report = &rtwsta->ra_report;
+	struct sk_buff *c2h = ra_data->c2h;
+	u8 mode, rate, bw, giltf, mac_id;
+
+	mac_id = RTW89_GET_PHY_C2H_RA_RPT_MACID(c2h->data);
+	if (mac_id != rtwsta->mac_id)
+		return;
+
+	memset(ra_report, 0, sizeof(*ra_report));
+
+	rate = RTW89_GET_PHY_C2H_RA_RPT_MCSNSS(c2h->data);
+	bw = RTW89_GET_PHY_C2H_RA_RPT_BW(c2h->data);
+	giltf = RTW89_GET_PHY_C2H_RA_RPT_GILTF(c2h->data);
+	mode = RTW89_GET_PHY_C2H_RA_RPT_MD_SEL(c2h->data);
+
+	switch (mode) {
+	case RTW89_RA_RPT_MODE_LEGACY:
+		ra_report->txrate.legacy = rtw89_ra_report_to_bitrate(rtwdev, rate);
+		break;
+	case RTW89_RA_RPT_MODE_HT:
+		ra_report->txrate.flags |= RATE_INFO_FLAGS_MCS;
+		if (rtwdev->fw.old_ht_ra_format)
+			rate = RTW89_MK_HT_RATE(FIELD_GET(RTW89_RA_RATE_MASK_NSS, rate),
+						FIELD_GET(RTW89_RA_RATE_MASK_MCS, rate));
+		else
+			rate = FIELD_GET(RTW89_RA_RATE_MASK_HT_MCS, rate);
+		ra_report->txrate.mcs = rate;
+		if (giltf)
+			ra_report->txrate.flags |= RATE_INFO_FLAGS_SHORT_GI;
+		break;
+	case RTW89_RA_RPT_MODE_VHT:
+		ra_report->txrate.flags |= RATE_INFO_FLAGS_VHT_MCS;
+		ra_report->txrate.mcs = FIELD_GET(RTW89_RA_RATE_MASK_MCS, rate);
+		ra_report->txrate.nss = FIELD_GET(RTW89_RA_RATE_MASK_NSS, rate) + 1;
+		if (giltf)
+			ra_report->txrate.flags |= RATE_INFO_FLAGS_SHORT_GI;
+		break;
+	case RTW89_RA_RPT_MODE_HE:
+		ra_report->txrate.flags |= RATE_INFO_FLAGS_HE_MCS;
+		ra_report->txrate.mcs = FIELD_GET(RTW89_RA_RATE_MASK_MCS, rate);
+		ra_report->txrate.nss = FIELD_GET(RTW89_RA_RATE_MASK_NSS, rate) + 1;
+		if (giltf == RTW89_GILTF_2XHE08 || giltf == RTW89_GILTF_1XHE08)
+			ra_report->txrate.he_gi = NL80211_RATE_INFO_HE_GI_0_8;
+		else if (giltf == RTW89_GILTF_2XHE16 || giltf == RTW89_GILTF_1XHE16)
+			ra_report->txrate.he_gi = NL80211_RATE_INFO_HE_GI_1_6;
+		else
+			ra_report->txrate.he_gi = NL80211_RATE_INFO_HE_GI_3_2;
+		break;
+	}
+
+	if (bw == RTW89_CHANNEL_WIDTH_80)
+		ra_report->txrate.bw = RATE_INFO_BW_80;
+	else if (bw == RTW89_CHANNEL_WIDTH_40)
+		ra_report->txrate.bw = RATE_INFO_BW_40;
+	else
+		ra_report->txrate.bw = RATE_INFO_BW_20;
+
+	ra_report->bit_rate = cfg80211_calculate_bitrate(&ra_report->txrate);
+	ra_report->hw_rate = FIELD_PREP(RTW89_HW_RATE_MASK_MOD, mode) |
+			     FIELD_PREP(RTW89_HW_RATE_MASK_VAL, rate);
+	sta->max_rc_amsdu_len = get_max_amsdu_len(rtwdev, ra_report);
+	rtwsta->max_agg_wait = sta->max_rc_amsdu_len / 1500 - 1;
+}
+
+static void
+rtw89_phy_c2h_ra_rpt(struct rtw89_dev *rtwdev, struct sk_buff *c2h, u32 len)
+{
+	struct rtw89_phy_iter_ra_data ra_data;
+
+	ra_data.rtwdev = rtwdev;
+	ra_data.c2h = c2h;
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_phy_c2h_ra_rpt_iter,
+					  &ra_data);
+}
+
+static
+void (* const rtw89_phy_c2h_ra_handler[])(struct rtw89_dev *rtwdev,
+					  struct sk_buff *c2h, u32 len) = {
+	[RTW89_PHY_C2H_FUNC_STS_RPT] = rtw89_phy_c2h_ra_rpt,
+	[RTW89_PHY_C2H_FUNC_MU_GPTBL_RPT] = NULL,
+	[RTW89_PHY_C2H_FUNC_TXSTS] = NULL,
+};
+
+void rtw89_phy_c2h_handle(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			  u32 len, u8 class, u8 func)
+{
+	void (*handler)(struct rtw89_dev *rtwdev,
+			struct sk_buff *c2h, u32 len) = NULL;
+
+	switch (class) {
+	case RTW89_PHY_C2H_CLASS_RA:
+		if (func < RTW89_PHY_C2H_FUNC_RA_MAX)
+			handler = rtw89_phy_c2h_ra_handler[func];
+		break;
+	default:
+		rtw89_info(rtwdev, "c2h class %d not support\n", class);
+		return;
+	}
+	if (!handler) {
+		rtw89_info(rtwdev, "c2h class %d func %d not support\n", class,
+			   func);
+		return;
+	}
+	handler(rtwdev, skb, len);
+}
+
+static u8 rtw89_phy_cfo_get_xcap_reg(struct rtw89_dev *rtwdev, bool sc_xo)
+{
+	u32 reg_mask;
+
+	if (sc_xo)
+		reg_mask = B_AX_XTAL_SC_XO_MASK;
+	else
+		reg_mask = B_AX_XTAL_SC_XI_MASK;
+
+	return (u8)rtw89_read32_mask(rtwdev, R_AX_XTAL_ON_CTRL0, reg_mask);
+}
+
+static void rtw89_phy_cfo_set_xcap_reg(struct rtw89_dev *rtwdev, bool sc_xo,
+				       u8 val)
+{
+	u32 reg_mask;
+
+	if (sc_xo)
+		reg_mask = B_AX_XTAL_SC_XO_MASK;
+	else
+		reg_mask = B_AX_XTAL_SC_XI_MASK;
+
+	rtw89_write32_mask(rtwdev, R_AX_XTAL_ON_CTRL0, reg_mask, val);
+}
+
+static void rtw89_phy_cfo_set_crystal_cap(struct rtw89_dev *rtwdev,
+					  u8 crystal_cap, bool force)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	u8 sc_xi_val, sc_xo_val;
+
+	if (!force && cfo->crystal_cap == crystal_cap)
+		return;
+	crystal_cap = clamp_t(u8, crystal_cap, 0, 127);
+	rtw89_phy_cfo_set_xcap_reg(rtwdev, true, crystal_cap);
+	rtw89_phy_cfo_set_xcap_reg(rtwdev, false, crystal_cap);
+	sc_xo_val = rtw89_phy_cfo_get_xcap_reg(rtwdev, true);
+	sc_xi_val = rtw89_phy_cfo_get_xcap_reg(rtwdev, false);
+	cfo->crystal_cap = sc_xi_val;
+	cfo->x_cap_ofst = (s8)((int)cfo->crystal_cap - cfo->def_x_cap);
+
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Set sc_xi=0x%x\n", sc_xi_val);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Set sc_xo=0x%x\n", sc_xo_val);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Get xcap_ofst=%d\n",
+		    cfo->x_cap_ofst);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Set xcap OK\n");
+}
+
+static void rtw89_phy_cfo_reset(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	u8 cap;
+
+	cfo->def_x_cap = cfo->crystal_cap_default & B_AX_XTAL_SC_MASK;
+	cfo->is_adjust = false;
+	if (cfo->crystal_cap == cfo->def_x_cap)
+		return;
+	cap = cfo->crystal_cap;
+	cap += (cap > cfo->def_x_cap ? -1 : 1);
+	rtw89_phy_cfo_set_crystal_cap(rtwdev, cap, false);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO,
+		    "(0x%x) approach to dflt_val=(0x%x)\n", cfo->crystal_cap,
+		    cfo->def_x_cap);
+}
+
+static void rtw89_dcfo_comp(struct rtw89_dev *rtwdev, s32 curr_cfo)
+{
+	bool is_linked = rtwdev->total_sta_assoc > 0;
+	s32 cfo_avg_312;
+	s32 dcfo_comp;
+	int sign;
+
+	if (!is_linked) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "DCFO: is_linked=%d\n",
+			    is_linked);
+		return;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "DCFO: curr_cfo=%d\n", curr_cfo);
+	if (curr_cfo == 0)
+		return;
+	dcfo_comp = rtw89_phy_read32_mask(rtwdev, R_DCFO, B_DCFO);
+	sign = curr_cfo > 0 ? 1 : -1;
+	cfo_avg_312 = (curr_cfo << 3) / 5 + sign * dcfo_comp;
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "DCFO: avg_cfo=%d\n", cfo_avg_312);
+	if (rtwdev->chip->chip_id == RTL8852A && rtwdev->hal.cv == CHIP_CBV)
+		cfo_avg_312 = -cfo_avg_312;
+	rtw89_phy_set_phy_regs(rtwdev, R_DCFO_COMP_S0, B_DCFO_COMP_S0_MSK,
+			       cfo_avg_312);
+}
+
+static void rtw89_dcfo_comp_init(struct rtw89_dev *rtwdev)
+{
+	rtw89_phy_set_phy_regs(rtwdev, R_DCFO_OPT, B_DCFO_OPT_EN, 1);
+	rtw89_phy_set_phy_regs(rtwdev, R_DCFO_WEIGHT, B_DCFO_WEIGHT_MSK, 8);
+	rtw89_write32_clr(rtwdev, R_AX_PWR_UL_CTRL2, B_AX_PWR_UL_CFO_MASK);
+}
+
+static void rtw89_phy_cfo_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	struct rtw89_efuse *efuse = &rtwdev->efuse;
+
+	cfo->crystal_cap_default = efuse->xtal_cap & B_AX_XTAL_SC_MASK;
+	cfo->crystal_cap = cfo->crystal_cap_default;
+	cfo->def_x_cap = cfo->crystal_cap;
+	cfo->is_adjust = false;
+	cfo->x_cap_ofst = 0;
+	cfo->rtw89_multi_cfo_mode = RTW89_TP_BASED_AVG_MODE;
+	cfo->apply_compensation = false;
+	cfo->residual_cfo_acc = 0;
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Default xcap=%0x\n",
+		    cfo->crystal_cap_default);
+	rtw89_phy_cfo_set_crystal_cap(rtwdev, cfo->crystal_cap_default, true);
+	rtw89_phy_set_phy_regs(rtwdev, R_DCFO, B_DCFO, 1);
+	rtw89_dcfo_comp_init(rtwdev);
+	cfo->cfo_timer_ms = 2000;
+	cfo->cfo_trig_by_timer_en = false;
+	cfo->phy_cfo_trk_cnt = 0;
+	cfo->phy_cfo_status = RTW89_PHY_DCFO_STATE_NORMAL;
+}
+
+static void rtw89_phy_cfo_crystal_cap_adjust(struct rtw89_dev *rtwdev,
+					     s32 curr_cfo)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	s8 crystal_cap = cfo->crystal_cap;
+	s32 cfo_abs = abs(curr_cfo);
+	int sign;
+
+	if (!cfo->is_adjust) {
+		if (cfo_abs > CFO_TRK_ENABLE_TH)
+			cfo->is_adjust = true;
+	} else {
+		if (cfo_abs < CFO_TRK_STOP_TH)
+			cfo->is_adjust = false;
+	}
+	if (!cfo->is_adjust) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Stop CFO tracking\n");
+		return;
+	}
+	sign = curr_cfo > 0 ? 1 : -1;
+	if (cfo_abs > CFO_TRK_STOP_TH_4)
+		crystal_cap += 7 * sign;
+	else if (cfo_abs > CFO_TRK_STOP_TH_3)
+		crystal_cap += 5 * sign;
+	else if (cfo_abs > CFO_TRK_STOP_TH_2)
+		crystal_cap += 3 * sign;
+	else if (cfo_abs > CFO_TRK_STOP_TH_1)
+		crystal_cap += 1 * sign;
+	else
+		return;
+	rtw89_phy_cfo_set_crystal_cap(rtwdev, (u8)crystal_cap, false);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO,
+		    "X_cap{Curr,Default}={0x%x,0x%x}\n",
+		    cfo->crystal_cap, cfo->def_x_cap);
+}
+
+static s32 rtw89_phy_average_cfo_calc(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	s32 cfo_khz_all = 0;
+	s32 cfo_cnt_all = 0;
+	s32 cfo_all_avg = 0;
+	u8 i;
+
+	if (rtwdev->total_sta_assoc != 1)
+		return 0;
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "one_entry_only\n");
+	for (i = 0; i < CFO_TRACK_MAX_USER; i++) {
+		if (cfo->cfo_cnt[i] == 0)
+			continue;
+		cfo_khz_all += cfo->cfo_tail[i];
+		cfo_cnt_all += cfo->cfo_cnt[i];
+		cfo_all_avg = phy_div(cfo_khz_all, cfo_cnt_all);
+		cfo->pre_cfo_avg[i] = cfo->cfo_avg[i];
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_CFO,
+		    "CFO track for macid = %d\n", i);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO,
+		    "Total cfo=%dK, pkt_cnt=%d, avg_cfo=%dK\n",
+		    cfo_khz_all, cfo_cnt_all, cfo_all_avg);
+	return cfo_all_avg;
+}
+
+static s32 rtw89_phy_multi_sta_cfo_calc(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	struct rtw89_traffic_stats *stats = &rtwdev->stats;
+	s32 target_cfo = 0;
+	s32 cfo_khz_all = 0;
+	s32 cfo_khz_all_tp_wgt = 0;
+	s32 cfo_avg = 0;
+	s32 max_cfo_lb = BIT(31);
+	s32 min_cfo_ub = GENMASK(30, 0);
+	u16 cfo_cnt_all = 0;
+	u8 active_entry_cnt = 0;
+	u8 sta_cnt = 0;
+	u32 tp_all = 0;
+	u8 i;
+	u8 cfo_tol = 0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Multi entry cfo_trk\n");
+	if (cfo->rtw89_multi_cfo_mode == RTW89_PKT_BASED_AVG_MODE) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Pkt based avg mode\n");
+		for (i = 0; i < CFO_TRACK_MAX_USER; i++) {
+			if (cfo->cfo_cnt[i] == 0)
+				continue;
+			cfo_khz_all += cfo->cfo_tail[i];
+			cfo_cnt_all += cfo->cfo_cnt[i];
+			cfo_avg = phy_div(cfo_khz_all, (s32)cfo_cnt_all);
+			rtw89_debug(rtwdev, RTW89_DBG_CFO,
+				    "Msta cfo=%d, pkt_cnt=%d, avg_cfo=%d\n",
+				    cfo_khz_all, cfo_cnt_all, cfo_avg);
+			target_cfo = cfo_avg;
+		}
+	} else if (cfo->rtw89_multi_cfo_mode == RTW89_ENTRY_BASED_AVG_MODE) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Entry based avg mode\n");
+		for (i = 0; i < CFO_TRACK_MAX_USER; i++) {
+			if (cfo->cfo_cnt[i] == 0)
+				continue;
+			cfo->cfo_avg[i] = phy_div(cfo->cfo_tail[i],
+						  (s32)cfo->cfo_cnt[i]);
+			cfo_khz_all += cfo->cfo_avg[i];
+			rtw89_debug(rtwdev, RTW89_DBG_CFO,
+				    "Macid=%d, cfo_avg=%d\n", i,
+				    cfo->cfo_avg[i]);
+		}
+		sta_cnt = rtwdev->total_sta_assoc;
+		cfo_avg = phy_div(cfo_khz_all, (s32)sta_cnt);
+		rtw89_debug(rtwdev, RTW89_DBG_CFO,
+			    "Msta cfo_acc=%d, ent_cnt=%d, avg_cfo=%d\n",
+			    cfo_khz_all, sta_cnt, cfo_avg);
+		target_cfo = cfo_avg;
+	} else if (cfo->rtw89_multi_cfo_mode == RTW89_TP_BASED_AVG_MODE) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "TP based avg mode\n");
+		cfo_tol = cfo->sta_cfo_tolerance;
+		for (i = 0; i < CFO_TRACK_MAX_USER; i++) {
+			sta_cnt++;
+			if (cfo->cfo_cnt[i] != 0) {
+				cfo->cfo_avg[i] = phy_div(cfo->cfo_tail[i],
+							  (s32)cfo->cfo_cnt[i]);
+				active_entry_cnt++;
+			} else {
+				cfo->cfo_avg[i] = cfo->pre_cfo_avg[i];
+			}
+			max_cfo_lb = max(cfo->cfo_avg[i] - cfo_tol, max_cfo_lb);
+			min_cfo_ub = min(cfo->cfo_avg[i] + cfo_tol, min_cfo_ub);
+			cfo_khz_all += cfo->cfo_avg[i];
+			/* need tp for each entry */
+			rtw89_debug(rtwdev, RTW89_DBG_CFO,
+				    "[%d] cfo_avg=%d, tp=tbd\n",
+				    i, cfo->cfo_avg[i]);
+			if (sta_cnt >= rtwdev->total_sta_assoc)
+				break;
+		}
+		tp_all = stats->rx_throughput; /* need tp for each entry */
+		cfo_avg =  phy_div(cfo_khz_all_tp_wgt, (s32)tp_all);
+
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Assoc sta cnt=%d\n",
+			    sta_cnt);
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Active sta cnt=%d\n",
+			    active_entry_cnt);
+		rtw89_debug(rtwdev, RTW89_DBG_CFO,
+			    "Msta cfo with tp_wgt=%d, avg_cfo=%d\n",
+			    cfo_khz_all_tp_wgt, cfo_avg);
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "cfo_lb=%d,cfo_ub=%d\n",
+			    max_cfo_lb, min_cfo_ub);
+		if (max_cfo_lb <= min_cfo_ub) {
+			rtw89_debug(rtwdev, RTW89_DBG_CFO,
+				    "cfo win_size=%d\n",
+				    min_cfo_ub - max_cfo_lb);
+			target_cfo = clamp(cfo_avg, max_cfo_lb, min_cfo_ub);
+		} else {
+			rtw89_debug(rtwdev, RTW89_DBG_CFO,
+				    "No intersection of cfo torlence windows\n");
+			target_cfo = phy_div(cfo_khz_all, (s32)sta_cnt);
+		}
+		for (i = 0; i < CFO_TRACK_MAX_USER; i++)
+			cfo->pre_cfo_avg[i] = cfo->cfo_avg[i];
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Target cfo=%d\n", target_cfo);
+	return target_cfo;
+}
+
+static void rtw89_phy_cfo_statistics_reset(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+
+	memset(&cfo->cfo_tail, 0, sizeof(cfo->cfo_tail));
+	memset(&cfo->cfo_cnt, 0, sizeof(cfo->cfo_cnt));
+	cfo->packet_count = 0;
+	cfo->packet_count_pre = 0;
+	cfo->cfo_avg_pre = 0;
+}
+
+static void rtw89_phy_cfo_dm(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	s32 new_cfo = 0;
+	bool x_cap_update = false;
+	u8 pre_x_cap = cfo->crystal_cap;
+
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "CFO:total_sta_assoc=%d\n",
+		    rtwdev->total_sta_assoc);
+	if (rtwdev->total_sta_assoc == 0) {
+		rtw89_phy_cfo_reset(rtwdev);
+		return;
+	}
+	if (cfo->packet_count == 0) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Pkt cnt = 0\n");
+		return;
+	}
+	if (cfo->packet_count == cfo->packet_count_pre) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "Pkt cnt doesn't change\n");
+		return;
+	}
+	if (rtwdev->total_sta_assoc == 1)
+		new_cfo = rtw89_phy_average_cfo_calc(rtwdev);
+	else
+		new_cfo = rtw89_phy_multi_sta_cfo_calc(rtwdev);
+	if (new_cfo == 0) {
+		rtw89_debug(rtwdev, RTW89_DBG_CFO, "curr_cfo=0\n");
+		return;
+	}
+	rtw89_phy_cfo_crystal_cap_adjust(rtwdev, new_cfo);
+	cfo->cfo_avg_pre = new_cfo;
+	x_cap_update =  cfo->crystal_cap == pre_x_cap ? false : true;
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Xcap_up=%d\n", x_cap_update);
+	rtw89_debug(rtwdev, RTW89_DBG_CFO, "Xcap: D:%x C:%x->%x, ofst=%d\n",
+		    cfo->def_x_cap, pre_x_cap, cfo->crystal_cap,
+		    cfo->x_cap_ofst);
+	if (x_cap_update) {
+		if (new_cfo > 0)
+			new_cfo -= CFO_SW_COMP_FINE_TUNE;
+		else
+			new_cfo += CFO_SW_COMP_FINE_TUNE;
+	}
+	rtw89_dcfo_comp(rtwdev, new_cfo);
+	rtw89_phy_cfo_statistics_reset(rtwdev);
+}
+
+void rtw89_phy_cfo_track_work(struct work_struct *work)
+{
+	struct rtw89_dev *rtwdev = container_of(work, struct rtw89_dev,
+						cfo_track_work.work);
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+
+	mutex_lock(&rtwdev->mutex);
+	if (!cfo->cfo_trig_by_timer_en)
+		goto out;
+	rtw89_leave_ps_mode(rtwdev);
+	rtw89_phy_cfo_dm(rtwdev);
+	ieee80211_queue_delayed_work(rtwdev->hw, &rtwdev->cfo_track_work,
+				     msecs_to_jiffies(cfo->cfo_timer_ms));
+out:
+	mutex_unlock(&rtwdev->mutex);
+}
+
+static void rtw89_phy_cfo_start_work(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+
+	ieee80211_queue_delayed_work(rtwdev->hw, &rtwdev->cfo_track_work,
+				     msecs_to_jiffies(cfo->cfo_timer_ms));
+}
+
+void rtw89_phy_cfo_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	struct rtw89_traffic_stats *stats = &rtwdev->stats;
+
+	switch (cfo->phy_cfo_status) {
+	case RTW89_PHY_DCFO_STATE_NORMAL:
+		if (stats->tx_throughput >= CFO_TP_UPPER) {
+			cfo->phy_cfo_status = RTW89_PHY_DCFO_STATE_ENHANCE;
+			cfo->cfo_trig_by_timer_en = true;
+			cfo->cfo_timer_ms = CFO_COMP_PERIOD;
+			rtw89_phy_cfo_start_work(rtwdev);
+		}
+		break;
+	case RTW89_PHY_DCFO_STATE_ENHANCE:
+		if (cfo->phy_cfo_trk_cnt >= CFO_PERIOD_CNT) {
+			cfo->phy_cfo_trk_cnt = 0;
+			cfo->cfo_trig_by_timer_en = false;
+		}
+		if (cfo->cfo_trig_by_timer_en == 1)
+			cfo->phy_cfo_trk_cnt++;
+		if (stats->tx_throughput <= CFO_TP_LOWER) {
+			cfo->phy_cfo_status = RTW89_PHY_DCFO_STATE_NORMAL;
+			cfo->phy_cfo_trk_cnt = 0;
+			cfo->cfo_trig_by_timer_en = false;
+		}
+		break;
+	default:
+		cfo->phy_cfo_status = RTW89_PHY_DCFO_STATE_NORMAL;
+		cfo->phy_cfo_trk_cnt = 0;
+		break;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_CFO,
+		    "[CFO]WatchDog tp=%d,state=%d,timer_en=%d,trk_cnt=%d,thermal=%ld\n",
+		    stats->tx_throughput, cfo->phy_cfo_status,
+		    cfo->cfo_trig_by_timer_en, cfo->phy_cfo_trk_cnt,
+		    ewma_thermal_read(&rtwdev->phystat.avg_thermal[0]));
+	if (cfo->cfo_trig_by_timer_en)
+		return;
+	rtw89_phy_cfo_dm(rtwdev);
+}
+
+void rtw89_phy_cfo_parse(struct rtw89_dev *rtwdev, s16 cfo_val,
+			 struct rtw89_rx_phy_ppdu *phy_ppdu)
+{
+	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
+	u8 macid = phy_ppdu->mac_id;
+
+	cfo->cfo_tail[macid] += cfo_val;
+	cfo->cfo_cnt[macid]++;
+	cfo->packet_count++;
+}
+
+static void rtw89_phy_stat_thermal_update(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_phy_stat *phystat = &rtwdev->phystat;
+	int i;
+	u8 th;
+
+	for (i = 0; i < rtwdev->chip->rf_path_num; i++) {
+		th = rtw89_chip_get_thermal(rtwdev, i);
+		if (th)
+			ewma_thermal_add(&phystat->avg_thermal[i], th);
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+			    "path(%d) thermal cur=%u avg=%ld", i, th,
+			    ewma_thermal_read(&phystat->avg_thermal[i]));
+	}
+}
+
+struct rtw89_phy_iter_rssi_data {
+	struct rtw89_dev *rtwdev;
+	struct rtw89_phy_ch_info *ch_info;
+	bool rssi_changed;
+};
+
+static void rtw89_phy_stat_rssi_update_iter(void *data,
+					    struct ieee80211_sta *sta)
+{
+	struct rtw89_sta *rtwsta = (struct rtw89_sta *)sta->drv_priv;
+	struct rtw89_phy_iter_rssi_data *rssi_data =
+					(struct rtw89_phy_iter_rssi_data *)data;
+	struct rtw89_phy_ch_info *ch_info = rssi_data->ch_info;
+	unsigned long rssi_curr;
+
+	rssi_curr = ewma_rssi_read(&rtwsta->avg_rssi);
+
+	if (rssi_curr < ch_info->rssi_min) {
+		ch_info->rssi_min = rssi_curr;
+		ch_info->rssi_min_macid = rtwsta->mac_id;
+	}
+
+	if (rtwsta->prev_rssi == 0) {
+		rtwsta->prev_rssi = rssi_curr;
+	} else if (abs((int)rtwsta->prev_rssi - (int)rssi_curr) > (3 << RSSI_FACTOR)) {
+		rtwsta->prev_rssi = rssi_curr;
+		rssi_data->rssi_changed = true;
+	}
+}
+
+static void rtw89_phy_stat_rssi_update(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_phy_iter_rssi_data rssi_data = {0};
+
+	rssi_data.rtwdev = rtwdev;
+	rssi_data.ch_info = &rtwdev->ch_info;
+	rssi_data.ch_info->rssi_min = U8_MAX;
+	ieee80211_iterate_stations_atomic(rtwdev->hw,
+					  rtw89_phy_stat_rssi_update_iter,
+					  &rssi_data);
+	if (rssi_data.rssi_changed)
+		rtw89_btc_ntfy_wl_sta(rtwdev);
+}
+
+static void rtw89_phy_stat_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_phy_stat *phystat = &rtwdev->phystat;
+	int i;
+
+	for (i = 0; i < rtwdev->chip->rf_path_num; i++)
+		ewma_thermal_init(&phystat->avg_thermal[i]);
+
+	rtw89_phy_stat_thermal_update(rtwdev);
+
+	memset(&phystat->cur_pkt_stat, 0, sizeof(phystat->cur_pkt_stat));
+	memset(&phystat->last_pkt_stat, 0, sizeof(phystat->last_pkt_stat));
+}
+
+void rtw89_phy_stat_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_phy_stat *phystat = &rtwdev->phystat;
+
+	rtw89_phy_stat_thermal_update(rtwdev);
+	rtw89_phy_stat_rssi_update(rtwdev);
+
+	phystat->last_pkt_stat = phystat->cur_pkt_stat;
+	memset(&phystat->cur_pkt_stat, 0, sizeof(phystat->cur_pkt_stat));
+}
+
+static u16 rtw89_phy_ccx_us_to_idx(struct rtw89_dev *rtwdev, u32 time_us)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+
+	return time_us >> (ilog2(CCX_US_BASE_RATIO) + env->ccx_unit_idx);
+}
+
+static u32 rtw89_phy_ccx_idx_to_us(struct rtw89_dev *rtwdev, u16 idx)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+
+	return idx << (ilog2(CCX_US_BASE_RATIO) + env->ccx_unit_idx);
+}
+
+static void rtw89_phy_ccx_top_setting_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+
+	env->ccx_manual_ctrl = false;
+	env->ccx_ongoing = false;
+	env->ccx_rac_lv = RTW89_RAC_RELEASE;
+	env->ccx_rpt_stamp = 0;
+	env->ccx_period = 0;
+	env->ccx_unit_idx = RTW89_CCX_32_US;
+	env->ccx_trigger_time = 0;
+	env->ccx_edcca_opt_bw_idx = RTW89_CCX_EDCCA_BW20_0;
+
+	rtw89_phy_set_phy_regs(rtwdev, R_CCX, B_CCX_EN_MSK, 1);
+	rtw89_phy_set_phy_regs(rtwdev, R_CCX, B_CCX_TRIG_OPT_MSK, 1);
+	rtw89_phy_set_phy_regs(rtwdev, R_CCX, B_MEASUREMENT_TRIG_MSK, 1);
+	rtw89_phy_set_phy_regs(rtwdev, R_CCX, B_CCX_EDCCA_OPT_MSK,
+			       RTW89_CCX_EDCCA_BW20_0);
+}
+
+static u16 rtw89_phy_ccx_get_report(struct rtw89_dev *rtwdev, u16 report,
+				    u16 score)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	u32 numer = 0;
+	u16 ret = 0;
+
+	numer = report * score + (env->ccx_period >> 1);
+	if (env->ccx_period)
+		ret = numer / env->ccx_period;
+
+	return ret >= score ? score - 1 : ret;
+}
+
+static void rtw89_phy_ccx_ms_to_period_unit(struct rtw89_dev *rtwdev,
+					    u16 time_ms, u32 *period,
+					    u32 *unit_idx)
+{
+	u32 idx;
+	u8 quotient;
+
+	if (time_ms >= CCX_MAX_PERIOD)
+		time_ms = CCX_MAX_PERIOD;
+
+	quotient = CCX_MAX_PERIOD_UNIT * time_ms / CCX_MAX_PERIOD;
+
+	if (quotient < 4)
+		idx = RTW89_CCX_4_US;
+	else if (quotient < 8)
+		idx = RTW89_CCX_8_US;
+	else if (quotient < 16)
+		idx = RTW89_CCX_16_US;
+	else
+		idx = RTW89_CCX_32_US;
+
+	*unit_idx = idx;
+	*period = (time_ms * MS_TO_4US_RATIO) >> idx;
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "[Trigger Time] period:%d, unit_idx:%d\n",
+		    *period, *unit_idx);
+}
+
+static void rtw89_phy_ccx_racing_release(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "lv:(%d)->(0)\n", env->ccx_rac_lv);
+
+	env->ccx_ongoing = false;
+	env->ccx_rac_lv = RTW89_RAC_RELEASE;
+	env->ifs_clm_app = RTW89_IFS_CLM_BACKGROUND;
+}
+
+static bool rtw89_phy_ifs_clm_th_update_check(struct rtw89_dev *rtwdev,
+					      struct rtw89_ccx_para_info *para)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	bool is_update = env->ifs_clm_app != para->ifs_clm_app;
+	u8 i = 0;
+	u16 *ifs_th_l = env->ifs_clm_th_l;
+	u16 *ifs_th_h = env->ifs_clm_th_h;
+	u32 ifs_th0_us = 0, ifs_th_times = 0;
+	u32 ifs_th_h_us[RTW89_IFS_CLM_NUM] = {0};
+
+	if (!is_update)
+		goto ifs_update_finished;
+
+	switch (para->ifs_clm_app) {
+	case RTW89_IFS_CLM_INIT:
+	case RTW89_IFS_CLM_BACKGROUND:
+	case RTW89_IFS_CLM_ACS:
+	case RTW89_IFS_CLM_DBG:
+	case RTW89_IFS_CLM_DIG:
+	case RTW89_IFS_CLM_TDMA_DIG:
+		ifs_th0_us = IFS_CLM_TH0_UPPER;
+		ifs_th_times = IFS_CLM_TH_MUL;
+		break;
+	case RTW89_IFS_CLM_DBG_MANUAL:
+		ifs_th0_us = para->ifs_clm_manual_th0;
+		ifs_th_times = para->ifs_clm_manual_th_times;
+		break;
+	default:
+		break;
+	}
+
+	/* Set sampling threshold for 4 different regions, unit in idx_cnt.
+	 * low[i] = high[i-1] + 1
+	 * high[i] = high[i-1] * ifs_th_times
+	 */
+	ifs_th_l[IFS_CLM_TH_START_IDX] = 0;
+	ifs_th_h_us[IFS_CLM_TH_START_IDX] = ifs_th0_us;
+	ifs_th_h[IFS_CLM_TH_START_IDX] = rtw89_phy_ccx_us_to_idx(rtwdev,
+								 ifs_th0_us);
+	for (i = 1; i < RTW89_IFS_CLM_NUM; i++) {
+		ifs_th_l[i] = ifs_th_h[i - 1] + 1;
+		ifs_th_h_us[i] = ifs_th_h_us[i - 1] * ifs_th_times;
+		ifs_th_h[i] = rtw89_phy_ccx_us_to_idx(rtwdev, ifs_th_h_us[i]);
+	}
+
+ifs_update_finished:
+	if (!is_update)
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "No need to update IFS_TH\n");
+
+	return is_update;
+}
+
+static void rtw89_phy_ifs_clm_set_th_reg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	u8 i = 0;
+
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T1, B_IFS_T1_TH_LOW_MSK,
+			       env->ifs_clm_th_l[0]);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T2, B_IFS_T2_TH_LOW_MSK,
+			       env->ifs_clm_th_l[1]);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T3, B_IFS_T3_TH_LOW_MSK,
+			       env->ifs_clm_th_l[2]);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T4, B_IFS_T4_TH_LOW_MSK,
+			       env->ifs_clm_th_l[3]);
+
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T1, B_IFS_T1_TH_HIGH_MSK,
+			       env->ifs_clm_th_h[0]);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T2, B_IFS_T2_TH_HIGH_MSK,
+			       env->ifs_clm_th_h[1]);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T3, B_IFS_T3_TH_HIGH_MSK,
+			       env->ifs_clm_th_h[2]);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T4, B_IFS_T4_TH_HIGH_MSK,
+			       env->ifs_clm_th_h[3]);
+
+	for (i = 0; i < RTW89_IFS_CLM_NUM; i++)
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "Update IFS_T%d_th{low, high} : {%d, %d}\n",
+			    i + 1, env->ifs_clm_th_l[i], env->ifs_clm_th_h[i]);
+}
+
+static void rtw89_phy_ifs_clm_setting_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	struct rtw89_ccx_para_info para = {0};
+
+	env->ifs_clm_app = RTW89_IFS_CLM_BACKGROUND;
+	env->ifs_clm_mntr_time = 0;
+
+	para.ifs_clm_app = RTW89_IFS_CLM_INIT;
+	if (rtw89_phy_ifs_clm_th_update_check(rtwdev, &para))
+		rtw89_phy_ifs_clm_set_th_reg(rtwdev);
+
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_COUNTER, B_IFS_COLLECT_EN,
+			       true);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T1, B_IFS_T1_EN_MSK, true);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T2, B_IFS_T2_EN_MSK, true);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T3, B_IFS_T3_EN_MSK, true);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_T4, B_IFS_T4_EN_MSK, true);
+}
+
+static int rtw89_phy_ccx_racing_ctrl(struct rtw89_dev *rtwdev,
+				     enum rtw89_env_racing_lv level)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	int ret = 0;
+
+	if (level >= RTW89_RAC_MAX_NUM) {
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "[WARNING] Wrong LV=%d\n", level);
+		return -EINVAL;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "ccx_ongoing=%d, level:(%d)->(%d)\n", env->ccx_ongoing,
+		    env->ccx_rac_lv, level);
+
+	if (env->ccx_ongoing) {
+		if (level <= env->ccx_rac_lv)
+			ret = -EINVAL;
+		else
+			env->ccx_ongoing = false;
+	}
+
+	if (ret == 0)
+		env->ccx_rac_lv = level;
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK, "ccx racing success=%d\n",
+		    !ret);
+
+	return ret;
+}
+
+static void rtw89_phy_ccx_trigger(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_COUNTER, B_IFS_COUNTER_CLR_MSK, 0);
+	rtw89_phy_set_phy_regs(rtwdev, R_CCX, B_MEASUREMENT_TRIG_MSK, 0);
+	rtw89_phy_set_phy_regs(rtwdev, R_IFS_COUNTER, B_IFS_COUNTER_CLR_MSK, 1);
+	rtw89_phy_set_phy_regs(rtwdev, R_CCX, B_MEASUREMENT_TRIG_MSK, 1);
+
+	env->ccx_rpt_stamp++;
+	env->ccx_ongoing = true;
+}
+
+static void rtw89_phy_ifs_clm_get_utility(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	u8 i = 0;
+	u32 res = 0;
+
+	env->ifs_clm_tx_ratio =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_tx, PERCENT);
+	env->ifs_clm_edcca_excl_cca_ratio =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_edcca_excl_cca,
+					 PERCENT);
+	env->ifs_clm_cck_fa_ratio =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_cckfa, PERCENT);
+	env->ifs_clm_ofdm_fa_ratio =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_ofdmfa, PERCENT);
+	env->ifs_clm_cck_cca_excl_fa_ratio =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_cckcca_excl_fa,
+					 PERCENT);
+	env->ifs_clm_ofdm_cca_excl_fa_ratio =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_ofdmcca_excl_fa,
+					 PERCENT);
+	env->ifs_clm_cck_fa_permil =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_cckfa, PERMIL);
+	env->ifs_clm_ofdm_fa_permil =
+		rtw89_phy_ccx_get_report(rtwdev, env->ifs_clm_ofdmfa, PERMIL);
+
+	for (i = 0; i < RTW89_IFS_CLM_NUM; i++) {
+		if (env->ifs_clm_his[i] > ENV_MNTR_IFSCLM_HIS_MAX) {
+			env->ifs_clm_ifs_avg[i] = ENV_MNTR_FAIL_DWORD;
+		} else {
+			env->ifs_clm_ifs_avg[i] =
+				rtw89_phy_ccx_idx_to_us(rtwdev,
+							env->ifs_clm_avg[i]);
+		}
+
+		res = rtw89_phy_ccx_idx_to_us(rtwdev, env->ifs_clm_cca[i]);
+		res += env->ifs_clm_his[i] >> 1;
+		if (env->ifs_clm_his[i])
+			res /= env->ifs_clm_his[i];
+		else
+			res = 0;
+		env->ifs_clm_cca_avg[i] = res;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "IFS-CLM ratio {Tx, EDCCA_exclu_cca} = {%d, %d}\n",
+		    env->ifs_clm_tx_ratio, env->ifs_clm_edcca_excl_cca_ratio);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "IFS-CLM FA ratio {CCK, OFDM} = {%d, %d}\n",
+		    env->ifs_clm_cck_fa_ratio, env->ifs_clm_ofdm_fa_ratio);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "IFS-CLM FA permil {CCK, OFDM} = {%d, %d}\n",
+		    env->ifs_clm_cck_fa_permil, env->ifs_clm_ofdm_fa_permil);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "IFS-CLM CCA_exclu_FA ratio {CCK, OFDM} = {%d, %d}\n",
+		    env->ifs_clm_cck_cca_excl_fa_ratio,
+		    env->ifs_clm_ofdm_cca_excl_fa_ratio);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "Time:[his, ifs_avg(us), cca_avg(us)]\n");
+	for (i = 0; i < RTW89_IFS_CLM_NUM; i++)
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK, "T%d:[%d, %d, %d]\n",
+			    i + 1, env->ifs_clm_his[i], env->ifs_clm_ifs_avg[i],
+			    env->ifs_clm_cca_avg[i]);
+}
+
+static bool rtw89_phy_ifs_clm_get_result(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	u8 i = 0;
+
+	if (rtw89_phy_read32_mask(rtwdev, R_IFSCNT, B_IFSCNT_DONE_MSK) == 0) {
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "Get IFS_CLM report Fail\n");
+		return false;
+	}
+
+	env->ifs_clm_tx =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CLM_TX_CNT,
+				      B_IFS_CLM_TX_CNT_MSK);
+	env->ifs_clm_edcca_excl_cca =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CLM_TX_CNT,
+				      B_IFS_CLM_EDCCA_EXCLUDE_CCA_FA_MSK);
+	env->ifs_clm_cckcca_excl_fa =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CLM_CCA,
+				      B_IFS_CLM_CCKCCA_EXCLUDE_FA_MSK);
+	env->ifs_clm_ofdmcca_excl_fa =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CLM_CCA,
+				      B_IFS_CLM_OFDMCCA_EXCLUDE_FA_MSK);
+	env->ifs_clm_cckfa =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CLM_FA,
+				      B_IFS_CLM_CCK_FA_MSK);
+	env->ifs_clm_ofdmfa =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CLM_FA,
+				      B_IFS_CLM_OFDM_FA_MSK);
+
+	env->ifs_clm_his[0] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_HIS, B_IFS_T1_HIS_MSK);
+	env->ifs_clm_his[1] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_HIS, B_IFS_T2_HIS_MSK);
+	env->ifs_clm_his[2] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_HIS, B_IFS_T3_HIS_MSK);
+	env->ifs_clm_his[3] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_HIS, B_IFS_T4_HIS_MSK);
+
+	env->ifs_clm_avg[0] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_AVG_L, B_IFS_T1_AVG_MSK);
+	env->ifs_clm_avg[1] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_AVG_L, B_IFS_T2_AVG_MSK);
+	env->ifs_clm_avg[2] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_AVG_H, B_IFS_T3_AVG_MSK);
+	env->ifs_clm_avg[3] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_AVG_H, B_IFS_T4_AVG_MSK);
+
+	env->ifs_clm_cca[0] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CCA_L, B_IFS_T1_CCA_MSK);
+	env->ifs_clm_cca[1] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CCA_L, B_IFS_T2_CCA_MSK);
+	env->ifs_clm_cca[2] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CCA_H, B_IFS_T3_CCA_MSK);
+	env->ifs_clm_cca[3] =
+		rtw89_phy_read32_mask(rtwdev, R_IFS_CCA_H, B_IFS_T4_CCA_MSK);
+
+	env->ifs_clm_total_ifs =
+		rtw89_phy_read32_mask(rtwdev, R_IFSCNT, B_IFSCNT_TOTAL_CNT_MSK);
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK, "IFS-CLM total_ifs = %d\n",
+		    env->ifs_clm_total_ifs);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "{Tx, EDCCA_exclu_cca} = {%d, %d}\n",
+		    env->ifs_clm_tx, env->ifs_clm_edcca_excl_cca);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "IFS-CLM FA{CCK, OFDM} = {%d, %d}\n",
+		    env->ifs_clm_cckfa, env->ifs_clm_ofdmfa);
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "IFS-CLM CCA_exclu_FA{CCK, OFDM} = {%d, %d}\n",
+		    env->ifs_clm_cckcca_excl_fa, env->ifs_clm_ofdmcca_excl_fa);
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK, "Time:[his, avg, cca]\n");
+	for (i = 0; i < RTW89_IFS_CLM_NUM; i++)
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "T%d:[%d, %d, %d]\n", i + 1, env->ifs_clm_his[i],
+			    env->ifs_clm_avg[i], env->ifs_clm_cca[i]);
+
+	rtw89_phy_ifs_clm_get_utility(rtwdev);
+
+	return true;
+}
+
+static int rtw89_phy_ifs_clm_set(struct rtw89_dev *rtwdev,
+				 struct rtw89_ccx_para_info *para)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	u32 period = 0;
+	u32 unit_idx = 0;
+
+	if (para->mntr_time == 0) {
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "[WARN] MNTR_TIME is 0\n");
+		return -EINVAL;
+	}
+
+	if (rtw89_phy_ccx_racing_ctrl(rtwdev, para->rac_lv))
+		return -EINVAL;
+
+	if (para->mntr_time != env->ifs_clm_mntr_time) {
+		rtw89_phy_ccx_ms_to_period_unit(rtwdev, para->mntr_time,
+						&period, &unit_idx);
+		rtw89_phy_set_phy_regs(rtwdev, R_IFS_COUNTER,
+				       B_IFS_CLM_PERIOD_MSK, period);
+		rtw89_phy_set_phy_regs(rtwdev, R_IFS_COUNTER,
+				       B_IFS_CLM_COUNTER_UNIT_MSK, unit_idx);
+
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "Update IFS-CLM time ((%d)) -> ((%d))\n",
+			    env->ifs_clm_mntr_time, para->mntr_time);
+
+		env->ifs_clm_mntr_time = para->mntr_time;
+		env->ccx_period = (u16)period;
+		env->ccx_unit_idx = (u8)unit_idx;
+	}
+
+	if (rtw89_phy_ifs_clm_th_update_check(rtwdev, para)) {
+		env->ifs_clm_app = para->ifs_clm_app;
+		rtw89_phy_ifs_clm_set_th_reg(rtwdev);
+	}
+
+	return 0;
+}
+
+void rtw89_phy_env_monitor_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	struct rtw89_ccx_para_info para = {0};
+	u8 chk_result = RTW89_PHY_ENV_MON_CCX_FAIL;
+
+	env->ccx_watchdog_result = RTW89_PHY_ENV_MON_CCX_FAIL;
+	if (env->ccx_manual_ctrl) {
+		rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+			    "CCX in manual ctrl\n");
+		return;
+	}
+
+	/* only ifs_clm for now */
+	if (rtw89_phy_ifs_clm_get_result(rtwdev))
+		env->ccx_watchdog_result |= RTW89_PHY_ENV_MON_IFS_CLM;
+
+	rtw89_phy_ccx_racing_release(rtwdev);
+	para.mntr_time = 1900;
+	para.rac_lv = RTW89_RAC_LV_1;
+	para.ifs_clm_app = RTW89_IFS_CLM_BACKGROUND;
+
+	if (rtw89_phy_ifs_clm_set(rtwdev, &para) == 0)
+		chk_result |= RTW89_PHY_ENV_MON_IFS_CLM;
+	if (chk_result)
+		rtw89_phy_ccx_trigger(rtwdev);
+
+	rtw89_debug(rtwdev, RTW89_DBG_PHY_TRACK,
+		    "get_result=0x%x, chk_result:0x%x\n",
+		    env->ccx_watchdog_result, chk_result);
+}
+
+static void rtw89_phy_dig_read_gain_table(struct rtw89_dev *rtwdev, int type)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	const struct rtw89_phy_dig_gain_cfg *cfg;
+	const char *msg;
+	u8 i;
+	s8 gain_base;
+	s8 *gain_arr;
+	u32 tmp;
+
+	switch (type) {
+	case RTW89_DIG_GAIN_LNA_G:
+		gain_arr = dig->lna_gain_g;
+		gain_base = LNA0_GAIN;
+		cfg = chip->dig_table->cfg_lna_g;
+		msg = "lna_gain_g";
+		break;
+	case RTW89_DIG_GAIN_TIA_G:
+		gain_arr = dig->tia_gain_g;
+		gain_base = TIA0_GAIN_G;
+		cfg = chip->dig_table->cfg_tia_g;
+		msg = "tia_gain_g";
+		break;
+	case RTW89_DIG_GAIN_LNA_A:
+		gain_arr = dig->lna_gain_a;
+		gain_base = LNA0_GAIN;
+		cfg = chip->dig_table->cfg_lna_a;
+		msg = "lna_gain_a";
+		break;
+	case RTW89_DIG_GAIN_TIA_A:
+		gain_arr = dig->tia_gain_a;
+		gain_base = TIA0_GAIN_A;
+		cfg = chip->dig_table->cfg_tia_a;
+		msg = "tia_gain_a";
+		break;
+	default:
+		return;
+	}
+
+	for (i = 0; i < cfg->size; i++) {
+		tmp = rtw89_phy_read32_mask(rtwdev, cfg->table[i].addr,
+					    cfg->table[i].mask);
+		tmp >>= DIG_GAIN_SHIFT;
+		gain_arr[i] = sign_extend32(tmp, U4_MAX_BIT) + gain_base;
+		gain_base += DIG_GAIN;
+
+		rtw89_debug(rtwdev, RTW89_DBG_DIG, "%s[%d]=%d\n",
+			    msg, i, gain_arr[i]);
+	}
+}
+
+static void rtw89_phy_dig_update_gain_para(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	u32 tmp;
+	u8 i;
+
+	tmp = rtw89_phy_read32_mask(rtwdev, R_PATH0_IB_PKPW,
+				    B_PATH0_IB_PKPW_MSK);
+	dig->ib_pkpwr = sign_extend32(tmp >> DIG_GAIN_SHIFT, U8_MAX_BIT);
+	dig->ib_pbk = rtw89_phy_read32_mask(rtwdev, R_PATH0_IB_PBK,
+					    B_PATH0_IB_PBK_MSK);
+	rtw89_debug(rtwdev, RTW89_DBG_DIG, "ib_pkpwr=%d, ib_pbk=%d\n",
+		    dig->ib_pkpwr, dig->ib_pbk);
+
+	for (i = RTW89_DIG_GAIN_LNA_G; i < RTW89_DIG_GAIN_MAX; i++)
+		rtw89_phy_dig_read_gain_table(rtwdev, i);
+}
+
+static const u8 rssi_nolink = 22;
+static const u8 igi_rssi_th[IGI_RSSI_TH_NUM] = {68, 84, 90, 98, 104};
+static const u16 fa_th_2g[FA_TH_NUM] = {22, 44, 66, 88};
+static const u16 fa_th_5g[FA_TH_NUM] = {4, 8, 12, 16};
+static const u16 fa_th_nolink[FA_TH_NUM] = {196, 352, 440, 528};
+
+static void rtw89_phy_dig_update_rssi_info(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_phy_ch_info *ch_info = &rtwdev->ch_info;
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	bool is_linked = rtwdev->total_sta_assoc > 0;
+
+	if (is_linked) {
+		dig->igi_rssi = ch_info->rssi_min >> 1;
+	} else {
+		rtw89_debug(rtwdev, RTW89_DBG_DIG, "RSSI update : NO Link\n");
+		dig->igi_rssi = rssi_nolink;
+	}
+}
+
+static void rtw89_phy_dig_update_para(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	bool is_linked = rtwdev->total_sta_assoc > 0;
+	const u16 *fa_th_src = NULL;
+
+	switch (rtwdev->hal.current_band_type) {
+	case RTW89_BAND_2G:
+		dig->lna_gain = dig->lna_gain_g;
+		dig->tia_gain = dig->tia_gain_g;
+		fa_th_src = is_linked ? fa_th_2g : fa_th_nolink;
+		dig->force_gaincode_idx_en = false;
+		dig->dyn_pd_th_en = true;
+		break;
+	case RTW89_BAND_5G:
+	default:
+		dig->lna_gain = dig->lna_gain_a;
+		dig->tia_gain = dig->tia_gain_a;
+		fa_th_src = is_linked ? fa_th_5g : fa_th_nolink;
+		dig->force_gaincode_idx_en = true;
+		dig->dyn_pd_th_en = true;
+		break;
+	}
+	memcpy(dig->fa_th, fa_th_src, sizeof(dig->fa_th));
+	memcpy(dig->igi_rssi_th, igi_rssi_th, sizeof(dig->igi_rssi_th));
+}
+
+static const u8 pd_low_th_offset = 20, dynamic_igi_min = 0x20;
+static const u8 igi_max_performance_mode = 0x5a;
+static const u8 dynamic_pd_threshold_max;
+
+static void rtw89_phy_dig_para_reset(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+
+	dig->cur_gaincode.lna_idx = LNA_IDX_MAX;
+	dig->cur_gaincode.tia_idx = TIA_IDX_MAX;
+	dig->cur_gaincode.rxb_idx = RXB_IDX_MAX;
+	dig->force_gaincode.lna_idx = LNA_IDX_MAX;
+	dig->force_gaincode.tia_idx = TIA_IDX_MAX;
+	dig->force_gaincode.rxb_idx = RXB_IDX_MAX;
+
+	dig->dyn_igi_max = igi_max_performance_mode;
+	dig->dyn_igi_min = dynamic_igi_min;
+	dig->dyn_pd_th_max = dynamic_pd_threshold_max;
+	dig->pd_low_th_ofst = pd_low_th_offset;
+	dig->is_linked_pre = false;
+}
+
+static void rtw89_phy_dig_init(struct rtw89_dev *rtwdev)
+{
+	rtw89_phy_dig_update_gain_para(rtwdev);
+	rtw89_phy_dig_reset(rtwdev);
+}
+
+static u8 rtw89_phy_dig_lna_idx_by_rssi(struct rtw89_dev *rtwdev, u8 rssi)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	u8 lna_idx;
+
+	if (rssi < dig->igi_rssi_th[0])
+		lna_idx = RTW89_DIG_GAIN_LNA_IDX6;
+	else if (rssi < dig->igi_rssi_th[1])
+		lna_idx = RTW89_DIG_GAIN_LNA_IDX5;
+	else if (rssi < dig->igi_rssi_th[2])
+		lna_idx = RTW89_DIG_GAIN_LNA_IDX4;
+	else if (rssi < dig->igi_rssi_th[3])
+		lna_idx = RTW89_DIG_GAIN_LNA_IDX3;
+	else if (rssi < dig->igi_rssi_th[4])
+		lna_idx = RTW89_DIG_GAIN_LNA_IDX2;
+	else
+		lna_idx = RTW89_DIG_GAIN_LNA_IDX1;
+
+	return lna_idx;
+}
+
+static u8 rtw89_phy_dig_tia_idx_by_rssi(struct rtw89_dev *rtwdev, u8 rssi)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	u8 tia_idx;
+
+	if (rssi < dig->igi_rssi_th[0])
+		tia_idx = RTW89_DIG_GAIN_TIA_IDX1;
+	else
+		tia_idx = RTW89_DIG_GAIN_TIA_IDX0;
+
+	return tia_idx;
+}
+
+#define IB_PBK_BASE 110
+#define WB_RSSI_BASE 10
+static u8 rtw89_phy_dig_rxb_idx_by_rssi(struct rtw89_dev *rtwdev, u8 rssi,
+					struct rtw89_agc_gaincode_set *set)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	s8 lna_gain = dig->lna_gain[set->lna_idx];
+	s8 tia_gain = dig->tia_gain[set->tia_idx];
+	s32 wb_rssi = rssi + lna_gain + tia_gain;
+	s32 rxb_idx_tmp = IB_PBK_BASE + WB_RSSI_BASE;
+	u8 rxb_idx;
+
+	rxb_idx_tmp += dig->ib_pkpwr - dig->ib_pbk - wb_rssi;
+	rxb_idx = clamp_t(s32, rxb_idx_tmp, RXB_IDX_MIN, RXB_IDX_MAX);
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG, "wb_rssi=%03d, rxb_idx_tmp=%03d\n",
+		    wb_rssi, rxb_idx_tmp);
+
+	return rxb_idx;
+}
+
+static void rtw89_phy_dig_gaincode_by_rssi(struct rtw89_dev *rtwdev, u8 rssi,
+					   struct rtw89_agc_gaincode_set *set)
+{
+	set->lna_idx = rtw89_phy_dig_lna_idx_by_rssi(rtwdev, rssi);
+	set->tia_idx = rtw89_phy_dig_tia_idx_by_rssi(rtwdev, rssi);
+	set->rxb_idx = rtw89_phy_dig_rxb_idx_by_rssi(rtwdev, rssi, set);
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG,
+		    "final_rssi=%03d, (lna,tia,rab)=(%d,%d,%02d)\n",
+		    rssi, set->lna_idx, set->tia_idx, set->rxb_idx);
+}
+
+#define IGI_OFFSET_MAX 25
+#define IGI_OFFSET_MUL 2
+static void rtw89_phy_dig_igi_offset_by_env(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	struct rtw89_env_monitor_info *env = &rtwdev->env_monitor;
+	enum rtw89_dig_noisy_level noisy_lv;
+	u8 igi_offset = dig->fa_rssi_ofst;
+	u16 fa_ratio = 0;
+
+	fa_ratio = env->ifs_clm_cck_fa_permil + env->ifs_clm_ofdm_fa_permil;
+
+	if (fa_ratio < dig->fa_th[0])
+		noisy_lv = RTW89_DIG_NOISY_LEVEL0;
+	else if (fa_ratio < dig->fa_th[1])
+		noisy_lv = RTW89_DIG_NOISY_LEVEL1;
+	else if (fa_ratio < dig->fa_th[2])
+		noisy_lv = RTW89_DIG_NOISY_LEVEL2;
+	else if (fa_ratio < dig->fa_th[3])
+		noisy_lv = RTW89_DIG_NOISY_LEVEL3;
+	else
+		noisy_lv = RTW89_DIG_NOISY_LEVEL_MAX;
+
+	if (noisy_lv == RTW89_DIG_NOISY_LEVEL0 && igi_offset < 2)
+		igi_offset = 0;
+	else
+		igi_offset += noisy_lv * IGI_OFFSET_MUL;
+
+	igi_offset = min_t(u8, igi_offset, IGI_OFFSET_MAX);
+	dig->fa_rssi_ofst = igi_offset;
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG,
+		    "fa_th: [+6 (%d) +4 (%d) +2 (%d) 0 (%d) -2 ]\n",
+		    dig->fa_th[3], dig->fa_th[2], dig->fa_th[1], dig->fa_th[0]);
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG,
+		    "fa(CCK,OFDM,ALL)=(%d,%d,%d)%%, noisy_lv=%d, ofst=%d\n",
+		    env->ifs_clm_cck_fa_permil, env->ifs_clm_ofdm_fa_permil,
+		    env->ifs_clm_cck_fa_permil + env->ifs_clm_ofdm_fa_permil,
+		    noisy_lv, igi_offset);
+}
+
+static void rtw89_phy_dig_set_lna_idx(struct rtw89_dev *rtwdev, u8 lna_idx)
+{
+	rtw89_phy_write32_mask(rtwdev, R_PATH0_LNA_INIT,
+			       B_PATH0_LNA_INIT_IDX_MSK, lna_idx);
+	rtw89_phy_write32_mask(rtwdev, R_PATH1_LNA_INIT,
+			       B_PATH1_LNA_INIT_IDX_MSK, lna_idx);
+}
+
+static void rtw89_phy_dig_set_tia_idx(struct rtw89_dev *rtwdev, u8 tia_idx)
+{
+	rtw89_phy_write32_mask(rtwdev, R_PATH0_TIA_INIT,
+			       B_PATH0_TIA_INIT_IDX_MSK, tia_idx);
+	rtw89_phy_write32_mask(rtwdev, R_PATH1_TIA_INIT,
+			       B_PATH1_TIA_INIT_IDX_MSK, tia_idx);
+}
+
+static void rtw89_phy_dig_set_rxb_idx(struct rtw89_dev *rtwdev, u8 rxb_idx)
+{
+	rtw89_phy_write32_mask(rtwdev, R_PATH0_RXB_INIT,
+			       B_PATH0_RXB_INIT_IDX_MSK, rxb_idx);
+	rtw89_phy_write32_mask(rtwdev, R_PATH1_RXB_INIT,
+			       B_PATH1_RXB_INIT_IDX_MSK, rxb_idx);
+}
+
+static void rtw89_phy_dig_set_igi_cr(struct rtw89_dev *rtwdev,
+				     const struct rtw89_agc_gaincode_set set)
+{
+	rtw89_phy_dig_set_lna_idx(rtwdev, set.lna_idx);
+	rtw89_phy_dig_set_tia_idx(rtwdev, set.tia_idx);
+	rtw89_phy_dig_set_rxb_idx(rtwdev, set.rxb_idx);
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG, "Set (lna,tia,rxb)=((%d,%d,%02d))\n",
+		    set.lna_idx, set.tia_idx, set.rxb_idx);
+}
+
+static const struct rtw89_reg_def sdagc_config[4] = {
+	{R_PATH0_P20_FOLLOW_BY_PAGCUGC, B_PATH0_P20_FOLLOW_BY_PAGCUGC_EN_MSK},
+	{R_PATH0_S20_FOLLOW_BY_PAGCUGC, B_PATH0_S20_FOLLOW_BY_PAGCUGC_EN_MSK},
+	{R_PATH1_P20_FOLLOW_BY_PAGCUGC, B_PATH1_P20_FOLLOW_BY_PAGCUGC_EN_MSK},
+	{R_PATH1_S20_FOLLOW_BY_PAGCUGC, B_PATH1_S20_FOLLOW_BY_PAGCUGC_EN_MSK},
+};
+
+static void rtw89_phy_dig_sdagc_follow_pagc_config(struct rtw89_dev *rtwdev,
+						   bool enable)
+{
+	u8 i = 0;
+
+	for (i = 0; i < ARRAY_SIZE(sdagc_config); i++)
+		rtw89_phy_write32_mask(rtwdev, sdagc_config[i].addr,
+				       sdagc_config[i].mask, enable);
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG, "sdagc_follow_pagc=%d\n", enable);
+}
+
+static void rtw89_phy_dig_dyn_pd_th(struct rtw89_dev *rtwdev, u8 rssi,
+				    bool enable)
+{
+	enum rtw89_bandwidth cbw = rtwdev->hal.current_band_width;
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	u8 final_rssi = 0, under_region = dig->pd_low_th_ofst;
+	u32 val = 0;
+
+	under_region += PD_TH_SB_FLTR_CMP_VAL;
+
+	switch (cbw) {
+	case RTW89_CHANNEL_WIDTH_40:
+		under_region += PD_TH_BW40_CMP_VAL;
+		break;
+	case RTW89_CHANNEL_WIDTH_80:
+		under_region += PD_TH_BW80_CMP_VAL;
+		break;
+	case RTW89_CHANNEL_WIDTH_20:
+		fallthrough;
+	default:
+		under_region += PD_TH_BW20_CMP_VAL;
+		break;
+	}
+
+	dig->dyn_pd_th_max = dig->igi_rssi;
+
+	final_rssi = min_t(u8, rssi, dig->igi_rssi);
+	final_rssi = clamp_t(u8, final_rssi, PD_TH_MIN_RSSI + under_region,
+			     PD_TH_MAX_RSSI + under_region);
+
+	if (enable) {
+		val = (final_rssi - under_region - PD_TH_MIN_RSSI) >> 1;
+		rtw89_debug(rtwdev, RTW89_DBG_DIG,
+			    "dyn_max=%d, final_rssi=%d, total=%d, PD_low=%d\n",
+			    dig->igi_rssi, final_rssi, under_region, val);
+	} else {
+		rtw89_debug(rtwdev, RTW89_DBG_DIG,
+			    "Dynamic PD th dsiabled, Set PD_low_bd=0\n");
+	}
+
+	rtw89_phy_write32_mask(rtwdev, R_SEG0R_PD, B_SEG0R_PD_LOWER_BOUND_MSK,
+			       val);
+	rtw89_phy_write32_mask(rtwdev, R_SEG0R_PD,
+			       B_SEG0R_PD_SPATIAL_REUSE_EN_MSK, enable);
+}
+
+void rtw89_phy_dig_reset(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+
+	dig->bypass_dig = false;
+	rtw89_phy_dig_para_reset(rtwdev);
+	rtw89_phy_dig_set_igi_cr(rtwdev, dig->force_gaincode);
+	rtw89_phy_dig_dyn_pd_th(rtwdev, rssi_nolink, false);
+	rtw89_phy_dig_sdagc_follow_pagc_config(rtwdev, false);
+	rtw89_phy_dig_update_para(rtwdev);
+}
+
+#define IGI_RSSI_MIN 10
+void rtw89_phy_dig(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dig_info *dig = &rtwdev->dig;
+	bool is_linked = rtwdev->total_sta_assoc > 0;
+
+	if (unlikely(dig->bypass_dig)) {
+		dig->bypass_dig = false;
+		return;
+	}
+
+	if (!dig->is_linked_pre && is_linked) {
+		rtw89_debug(rtwdev, RTW89_DBG_DIG, "First connected\n");
+		rtw89_phy_dig_update_para(rtwdev);
+	} else if (dig->is_linked_pre && !is_linked) {
+		rtw89_debug(rtwdev, RTW89_DBG_DIG, "First disconnected\n");
+		rtw89_phy_dig_update_para(rtwdev);
+	}
+	dig->is_linked_pre = is_linked;
+
+	rtw89_phy_dig_igi_offset_by_env(rtwdev);
+	rtw89_phy_dig_update_rssi_info(rtwdev);
+
+	dig->dyn_igi_min = (dig->igi_rssi > IGI_RSSI_MIN) ?
+			    dig->igi_rssi - IGI_RSSI_MIN : 0;
+	dig->dyn_igi_max = dig->dyn_igi_min + IGI_OFFSET_MAX;
+	dig->igi_fa_rssi = dig->dyn_igi_min + dig->fa_rssi_ofst;
+
+	dig->igi_fa_rssi = clamp(dig->igi_fa_rssi, dig->dyn_igi_min,
+				 dig->dyn_igi_max);
+
+	rtw89_debug(rtwdev, RTW89_DBG_DIG,
+		    "rssi=%03d, dyn(max,min)=(%d,%d), final_rssi=%d\n",
+		    dig->igi_rssi, dig->dyn_igi_max, dig->dyn_igi_min,
+		    dig->igi_fa_rssi);
+
+	if (dig->force_gaincode_idx_en) {
+		rtw89_phy_dig_set_igi_cr(rtwdev, dig->force_gaincode);
+		rtw89_debug(rtwdev, RTW89_DBG_DIG,
+			    "Force gaincode index enabled.\n");
+	} else {
+		rtw89_phy_dig_gaincode_by_rssi(rtwdev, dig->igi_fa_rssi,
+					       &dig->cur_gaincode);
+		rtw89_phy_dig_set_igi_cr(rtwdev, dig->cur_gaincode);
+	}
+
+	rtw89_phy_dig_dyn_pd_th(rtwdev, dig->igi_fa_rssi, dig->dyn_pd_th_en);
+
+	if (dig->dyn_pd_th_en && dig->igi_fa_rssi > dig->dyn_pd_th_max)
+		rtw89_phy_dig_sdagc_follow_pagc_config(rtwdev, true);
+	else
+		rtw89_phy_dig_sdagc_follow_pagc_config(rtwdev, false);
+}
+
+static void rtw89_phy_env_monitor_init(struct rtw89_dev *rtwdev)
+{
+	rtw89_phy_ccx_top_setting_init(rtwdev);
+	rtw89_phy_ifs_clm_setting_init(rtwdev);
+}
+
+void rtw89_phy_dm_init(struct rtw89_dev *rtwdev)
+{
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+
+	rtw89_phy_stat_init(rtwdev);
+
+	rtw89_chip_bb_sethw(rtwdev);
+
+	rtw89_phy_env_monitor_init(rtwdev);
+	rtw89_phy_dig_init(rtwdev);
+	rtw89_phy_cfo_init(rtwdev);
+
+	rtw89_phy_init_rf_nctl(rtwdev);
+	rtw89_chip_rfk_init(rtwdev);
+	rtw89_load_txpwr_table(rtwdev, chip->byr_table);
+	rtw89_chip_set_txpwr_ctrl(rtwdev);
+	rtw89_chip_power_trim(rtwdev);
+}
+
+void rtw89_phy_set_bss_color(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif)
+{
+	enum rtw89_phy_idx phy_idx = RTW89_PHY_0;
+	u8 bss_color;
+
+	if (!vif->bss_conf.he_support || !vif->bss_conf.assoc)
+		return;
+
+	bss_color = vif->bss_conf.he_bss_color.color;
+
+	rtw89_phy_write32_idx(rtwdev, R_BSS_CLR_MAP, B_BSS_CLR_MAP_VLD0, 0x1,
+			      phy_idx);
+	rtw89_phy_write32_idx(rtwdev, R_BSS_CLR_MAP, B_BSS_CLR_MAP_TGT, bss_color,
+			      phy_idx);
+	rtw89_phy_write32_idx(rtwdev, R_BSS_CLR_MAP, B_BSS_CLR_MAP_STAID,
+			      vif->bss_conf.aid, phy_idx);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/phy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/phy.h
@@ -0,0 +1,311 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_PHY_H__
+#define __RTW89_PHY_H__
+
+#include "core.h"
+
+#define RTW89_PHY_ADDR_OFFSET	0x10000
+
+#define get_phy_headline(addr)		FIELD_GET(GENMASK(31, 28), addr)
+#define PHY_HEADLINE_VALID	0xf
+#define get_phy_target(addr)		FIELD_GET(GENMASK(27, 0), addr)
+#define get_phy_compare(rfe, cv)	(FIELD_PREP(GENMASK(23, 16), rfe) | \
+					 FIELD_PREP(GENMASK(7, 0), cv))
+
+#define get_phy_cond(addr)		FIELD_GET(GENMASK(31, 28), addr)
+#define get_phy_cond_rfe(addr)		FIELD_GET(GENMASK(23, 16), addr)
+#define get_phy_cond_pkg(addr)		FIELD_GET(GENMASK(15, 8), addr)
+#define get_phy_cond_cv(addr)		FIELD_GET(GENMASK(7, 0), addr)
+#define phy_div(a, b) ({typeof(b) _b = (b); (_b) ? ((a) / (_b)) : 0; })
+#define PHY_COND_BRANCH_IF	0x8
+#define PHY_COND_BRANCH_ELIF	0x9
+#define PHY_COND_BRANCH_ELSE	0xa
+#define PHY_COND_BRANCH_END	0xb
+#define PHY_COND_CHECK		0x4
+#define PHY_COND_DONT_CARE	0xff
+
+#define RA_MASK_CCK_RATES	GENMASK_ULL(3, 0)
+#define RA_MASK_OFDM_RATES	GENMASK_ULL(11, 4)
+#define RA_MASK_SUBCCK_RATES	0x5ULL
+#define RA_MASK_SUBOFDM_RATES	0x10ULL
+#define RA_MASK_HT_1SS_RATES	GENMASK_ULL(19, 12)
+#define RA_MASK_HT_2SS_RATES	GENMASK_ULL(31, 24)
+#define RA_MASK_HT_3SS_RATES	GENMASK_ULL(43, 36)
+#define RA_MASK_HT_4SS_RATES	GENMASK_ULL(55, 48)
+#define RA_MASK_HT_RATES	GENMASK_ULL(55, 12)
+#define RA_MASK_VHT_1SS_RATES	GENMASK_ULL(21, 12)
+#define RA_MASK_VHT_2SS_RATES	GENMASK_ULL(33, 24)
+#define RA_MASK_VHT_3SS_RATES	GENMASK_ULL(45, 36)
+#define RA_MASK_VHT_4SS_RATES	GENMASK_ULL(57, 48)
+#define RA_MASK_VHT_RATES	GENMASK_ULL(57, 12)
+#define RA_MASK_HE_1SS_RATES	GENMASK_ULL(23, 12)
+#define RA_MASK_HE_2SS_RATES	GENMASK_ULL(35, 24)
+#define RA_MASK_HE_3SS_RATES	GENMASK_ULL(47, 36)
+#define RA_MASK_HE_4SS_RATES	GENMASK_ULL(59, 48)
+#define RA_MASK_HE_RATES	GENMASK_ULL(59, 12)
+
+#define CFO_TRK_ENABLE_TH (2 << 2)
+#define CFO_TRK_STOP_TH_4 (30 << 2)
+#define CFO_TRK_STOP_TH_3 (20 << 2)
+#define CFO_TRK_STOP_TH_2 (10 << 2)
+#define CFO_TRK_STOP_TH_1 (00 << 2)
+#define CFO_TRK_STOP_TH (2 << 2)
+#define CFO_SW_COMP_FINE_TUNE (2 << 2)
+#define CFO_PERIOD_CNT 15
+#define CFO_TP_UPPER 100
+#define CFO_TP_LOWER 50
+#define CFO_COMP_PERIOD 250
+#define CFO_COMP_WEIGHT 8
+#define MAX_CFO_TOLERANCE 30
+
+#define CCX_MAX_PERIOD 2097
+#define CCX_MAX_PERIOD_UNIT 32
+#define MS_TO_4US_RATIO 250
+#define ENV_MNTR_FAIL_DWORD 0xffffffff
+#define ENV_MNTR_IFSCLM_HIS_MAX 127
+#define PERMIL 1000
+#define PERCENT 100
+#define IFS_CLM_TH0_UPPER 64
+#define IFS_CLM_TH_MUL 4
+#define IFS_CLM_TH_START_IDX 0
+
+#define TIA0_GAIN_A 12
+#define TIA0_GAIN_G 16
+#define LNA0_GAIN (-24)
+#define U4_MAX_BIT 3
+#define U8_MAX_BIT 7
+#define DIG_GAIN_SHIFT 2
+#define DIG_GAIN 8
+
+#define LNA_IDX_MAX 6
+#define LNA_IDX_MIN 0
+#define TIA_IDX_MAX 1
+#define TIA_IDX_MIN 0
+#define RXB_IDX_MAX 31
+#define RXB_IDX_MIN 0
+
+#define PD_TH_MAX_RSSI 70
+#define PD_TH_MIN_RSSI 8
+#define PD_TH_BW80_CMP_VAL 6
+#define PD_TH_BW40_CMP_VAL 3
+#define PD_TH_BW20_CMP_VAL 0
+#define PD_TH_CMP_VAL 3
+#define PD_TH_SB_FLTR_CMP_VAL 7
+
+#define PHYSTS_MGNT BIT(RTW89_RX_TYPE_MGNT)
+#define PHYSTS_CTRL BIT(RTW89_RX_TYPE_CTRL)
+#define PHYSTS_DATA BIT(RTW89_RX_TYPE_DATA)
+#define PHYSTS_RSVD BIT(RTW89_RX_TYPE_RSVD)
+#define PPDU_FILTER_BITMAP (PHYSTS_MGNT | PHYSTS_DATA)
+
+enum rtw89_phy_c2h_ra_func {
+	RTW89_PHY_C2H_FUNC_STS_RPT,
+	RTW89_PHY_C2H_FUNC_MU_GPTBL_RPT,
+	RTW89_PHY_C2H_FUNC_TXSTS,
+	RTW89_PHY_C2H_FUNC_RA_MAX,
+};
+
+enum rtw89_phy_c2h_class {
+	RTW89_PHY_C2H_CLASS_RUA,
+	RTW89_PHY_C2H_CLASS_RA,
+	RTW89_PHY_C2H_CLASS_DM,
+	RTW89_PHY_C2H_CLASS_BTC_MIN = 0x10,
+	RTW89_PHY_C2H_CLASS_BTC_MAX = 0x17,
+	RTW89_PHY_C2H_CLASS_MAX,
+};
+
+enum rtw89_env_monitor_result_level {
+	RTW89_PHY_ENV_MON_CCX_FAIL = 0,
+	RTW89_PHY_ENV_MON_NHM = BIT(0),
+	RTW89_PHY_ENV_MON_CLM = BIT(1),
+	RTW89_PHY_ENV_MON_FAHM = BIT(2),
+	RTW89_PHY_ENV_MON_IFS_CLM = BIT(3),
+	RTW89_PHY_ENV_MON_EDCCA_CLM = BIT(4),
+};
+
+#define CCX_US_BASE_RATIO 4
+enum rtw89_ccx_unit {
+	RTW89_CCX_4_US = 0,
+	RTW89_CCX_8_US = 1,
+	RTW89_CCX_16_US = 2,
+	RTW89_CCX_32_US = 3
+};
+
+enum rtw89_dig_gain_type {
+	RTW89_DIG_GAIN_LNA_G = 0,
+	RTW89_DIG_GAIN_TIA_G = 1,
+	RTW89_DIG_GAIN_LNA_A = 2,
+	RTW89_DIG_GAIN_TIA_A = 3,
+	RTW89_DIG_GAIN_MAX = 4
+};
+
+enum rtw89_dig_gain_lna_idx {
+	RTW89_DIG_GAIN_LNA_IDX1 = 1,
+	RTW89_DIG_GAIN_LNA_IDX2 = 2,
+	RTW89_DIG_GAIN_LNA_IDX3 = 3,
+	RTW89_DIG_GAIN_LNA_IDX4 = 4,
+	RTW89_DIG_GAIN_LNA_IDX5 = 5,
+	RTW89_DIG_GAIN_LNA_IDX6 = 6
+};
+
+enum rtw89_dig_gain_tia_idx {
+	RTW89_DIG_GAIN_TIA_IDX0 = 0,
+	RTW89_DIG_GAIN_TIA_IDX1 = 1
+};
+
+struct rtw89_txpwr_byrate_cfg {
+	enum rtw89_band band;
+	enum rtw89_nss nss;
+	enum rtw89_rate_section rs;
+	u8 shf;
+	u8 len;
+	u32 data;
+};
+
+#define DELTA_SWINGIDX_SIZE 30
+
+struct rtw89_txpwr_track_cfg {
+	const u8 (*delta_swingidx_5gb_n)[DELTA_SWINGIDX_SIZE];
+	const u8 (*delta_swingidx_5gb_p)[DELTA_SWINGIDX_SIZE];
+	const u8 (*delta_swingidx_5ga_n)[DELTA_SWINGIDX_SIZE];
+	const u8 (*delta_swingidx_5ga_p)[DELTA_SWINGIDX_SIZE];
+	const u8 *delta_swingidx_2gb_n;
+	const u8 *delta_swingidx_2gb_p;
+	const u8 *delta_swingidx_2ga_n;
+	const u8 *delta_swingidx_2ga_p;
+	const u8 *delta_swingidx_2g_cck_b_n;
+	const u8 *delta_swingidx_2g_cck_b_p;
+	const u8 *delta_swingidx_2g_cck_a_n;
+	const u8 *delta_swingidx_2g_cck_a_p;
+};
+
+struct rtw89_phy_dig_gain_cfg {
+	const struct rtw89_reg_def *table;
+	u8 size;
+};
+
+struct rtw89_phy_dig_gain_table {
+	const struct rtw89_phy_dig_gain_cfg *cfg_lna_g;
+	const struct rtw89_phy_dig_gain_cfg *cfg_tia_g;
+	const struct rtw89_phy_dig_gain_cfg *cfg_lna_a;
+	const struct rtw89_phy_dig_gain_cfg *cfg_tia_a;
+};
+
+struct rtw89_phy_reg3_tbl {
+	const struct rtw89_reg3_def *reg3;
+	int size;
+};
+
+#define DECLARE_PHY_REG3_TBL(_name)			\
+const struct rtw89_phy_reg3_tbl _name ## _tbl = {	\
+	.reg3 = _name,					\
+	.size = ARRAY_SIZE(_name),			\
+}
+
+static inline void rtw89_phy_write8(struct rtw89_dev *rtwdev,
+				    u32 addr, u8 data)
+{
+	rtw89_write8(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, data);
+}
+
+static inline void rtw89_phy_write16(struct rtw89_dev *rtwdev,
+				     u32 addr, u16 data)
+{
+	rtw89_write16(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, data);
+}
+
+static inline void rtw89_phy_write32(struct rtw89_dev *rtwdev,
+				     u32 addr, u32 data)
+{
+	rtw89_write32(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, data);
+}
+
+static inline void rtw89_phy_write32_set(struct rtw89_dev *rtwdev,
+					 u32 addr, u32 bits)
+{
+	rtw89_write32_set(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, bits);
+}
+
+static inline void rtw89_phy_write32_clr(struct rtw89_dev *rtwdev,
+					 u32 addr, u32 bits)
+{
+	rtw89_write32_clr(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, bits);
+}
+
+static inline void rtw89_phy_write32_mask(struct rtw89_dev *rtwdev,
+					  u32 addr, u32 mask, u32 data)
+{
+	rtw89_write32_mask(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, mask, data);
+}
+
+static inline u8 rtw89_phy_read8(struct rtw89_dev *rtwdev, u32 addr)
+{
+	return rtw89_read8(rtwdev, addr | RTW89_PHY_ADDR_OFFSET);
+}
+
+static inline u16 rtw89_phy_read16(struct rtw89_dev *rtwdev, u32 addr)
+{
+	return rtw89_read16(rtwdev, addr | RTW89_PHY_ADDR_OFFSET);
+}
+
+static inline u32 rtw89_phy_read32(struct rtw89_dev *rtwdev, u32 addr)
+{
+	return rtw89_read32(rtwdev, addr | RTW89_PHY_ADDR_OFFSET);
+}
+
+static inline u32 rtw89_phy_read32_mask(struct rtw89_dev *rtwdev,
+					u32 addr, u32 mask)
+{
+	return rtw89_read32_mask(rtwdev, addr | RTW89_PHY_ADDR_OFFSET, mask);
+}
+
+void rtw89_phy_write_reg3_tbl(struct rtw89_dev *rtwdev,
+			      const struct rtw89_phy_reg3_tbl *tbl);
+u8 rtw89_phy_get_txsc(struct rtw89_dev *rtwdev,
+		      struct rtw89_channel_params *param,
+		      enum rtw89_bandwidth dbw);
+u32 rtw89_phy_read_rf(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+		      u32 addr, u32 mask);
+bool rtw89_phy_write_rf(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path,
+			u32 addr, u32 mask, u32 data);
+void rtw89_phy_init_bb_reg(struct rtw89_dev *rtwdev);
+void rtw89_phy_init_rf_reg(struct rtw89_dev *rtwdev);
+void rtw89_phy_dm_init(struct rtw89_dev *rtwdev);
+void rtw89_phy_write32_idx(struct rtw89_dev *rtwdev, u32 addr, u32 mask,
+			   u32 data, enum rtw89_phy_idx phy_idx);
+void rtw89_phy_load_txpwr_byrate(struct rtw89_dev *rtwdev,
+				 const struct rtw89_txpwr_table *tbl);
+s8 rtw89_phy_read_txpwr_byrate(struct rtw89_dev *rtwdev,
+			       const struct rtw89_rate_desc *rate_desc);
+void rtw89_phy_fill_txpwr_limit(struct rtw89_dev *rtwdev,
+				struct rtw89_txpwr_limit *lmt,
+				u8 ntx);
+void rtw89_phy_fill_txpwr_limit_ru(struct rtw89_dev *rtwdev,
+				   struct rtw89_txpwr_limit_ru *lmt_ru,
+				   u8 ntx);
+s8 rtw89_phy_read_txpwr_limit(struct rtw89_dev *rtwdev,
+			      u8 bw, u8 ntx, u8 rs, u8 bf, u8 ch);
+void rtw89_phy_ra_assoc(struct rtw89_dev *rtwdev, struct ieee80211_sta *sta);
+void rtw89_phy_ra_update(struct rtw89_dev *rtwdev);
+void rtw89_phy_ra_updata_sta(struct rtw89_dev *rtwdev, struct ieee80211_sta *sta);
+void rtw89_phy_rate_pattern_vif(struct rtw89_dev *rtwdev,
+				struct ieee80211_vif *vif,
+				const struct cfg80211_bitrate_mask *mask);
+void rtw89_phy_c2h_handle(struct rtw89_dev *rtwdev, struct sk_buff *skb,
+			  u32 len, u8 class, u8 func);
+void rtw89_phy_cfo_track(struct rtw89_dev *rtwdev);
+void rtw89_phy_cfo_track_work(struct work_struct *work);
+void rtw89_phy_cfo_parse(struct rtw89_dev *rtwdev, s16 cfo_val,
+			 struct rtw89_rx_phy_ppdu *phy_ppdu);
+void rtw89_phy_stat_track(struct rtw89_dev *rtwdev);
+void rtw89_phy_env_monitor_track(struct rtw89_dev *rtwdev);
+void rtw89_phy_set_phy_regs(struct rtw89_dev *rtwdev, u32 addr, u32 mask,
+			    u32 val);
+void rtw89_phy_dig_reset(struct rtw89_dev *rtwdev);
+void rtw89_phy_dig(struct rtw89_dev *rtwdev);
+void rtw89_phy_set_bss_color(struct rtw89_dev *rtwdev, struct ieee80211_vif *vif);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/ps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/ps.c
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "coex.h"
+#include "core.h"
+#include "debug.h"
+#include "fw.h"
+#include "mac.h"
+#include "ps.h"
+#include "reg.h"
+#include "util.h"
+
+static int rtw89_fw_leave_lps_check(struct rtw89_dev *rtwdev, u8 macid)
+{
+	u32 pwr_en_bit = 0xE;
+	u32 chk_msk = pwr_en_bit << (4 * macid);
+	u32 polling;
+	int ret;
+
+	ret = read_poll_timeout_atomic(rtw89_read32_mask, polling, !polling,
+				       1000, 50000, false, rtwdev,
+				       R_AX_PPWRBIT_SETTING, chk_msk);
+	if (ret) {
+		rtw89_info(rtwdev, "rtw89: failed to leave lps state\n");
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void __rtw89_enter_ps_mode(struct rtw89_dev *rtwdev)
+{
+	if (!rtwdev->ps_mode)
+		return;
+
+	if (test_and_set_bit(RTW89_FLAG_LOW_POWER_MODE, rtwdev->flags))
+		return;
+
+	rtw89_mac_power_mode_change(rtwdev, true);
+}
+
+void __rtw89_leave_ps_mode(struct rtw89_dev *rtwdev)
+{
+	if (!rtwdev->ps_mode)
+		return;
+
+	if (test_and_clear_bit(RTW89_FLAG_LOW_POWER_MODE, rtwdev->flags))
+		rtw89_mac_power_mode_change(rtwdev, false);
+}
+
+static void __rtw89_enter_lps(struct rtw89_dev *rtwdev, u8 mac_id)
+{
+	struct rtw89_lps_parm lps_param = {
+		.macid = mac_id,
+		.psmode = RTW89_MAC_AX_PS_MODE_LEGACY,
+		.lastrpwm = RTW89_LAST_RPWM_PS,
+	};
+
+	rtw89_btc_ntfy_radio_state(rtwdev, BTC_RFCTRL_FW_CTRL);
+	rtw89_fw_h2c_lps_parm(rtwdev, &lps_param);
+}
+
+static void __rtw89_leave_lps(struct rtw89_dev *rtwdev, u8 mac_id)
+{
+	struct rtw89_lps_parm lps_param = {
+		.macid = mac_id,
+		.psmode = RTW89_MAC_AX_PS_MODE_ACTIVE,
+		.lastrpwm = RTW89_LAST_RPWM_ACTIVE,
+	};
+
+	rtw89_fw_h2c_lps_parm(rtwdev, &lps_param);
+	rtw89_fw_leave_lps_check(rtwdev, 0);
+	rtw89_btc_ntfy_radio_state(rtwdev, BTC_RFCTRL_WL_ON);
+}
+
+void rtw89_leave_ps_mode(struct rtw89_dev *rtwdev)
+{
+	lockdep_assert_held(&rtwdev->mutex);
+
+	__rtw89_leave_ps_mode(rtwdev);
+}
+
+void rtw89_enter_lps(struct rtw89_dev *rtwdev, u8 mac_id)
+{
+	lockdep_assert_held(&rtwdev->mutex);
+
+	if (test_and_set_bit(RTW89_FLAG_LEISURE_PS, rtwdev->flags))
+		return;
+
+	__rtw89_enter_lps(rtwdev, mac_id);
+	__rtw89_enter_ps_mode(rtwdev);
+}
+
+static void rtw89_leave_lps_vif(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	if (rtwvif->wifi_role != RTW89_WIFI_ROLE_STATION)
+		return;
+
+	__rtw89_leave_ps_mode(rtwdev);
+	__rtw89_leave_lps(rtwdev, rtwvif->mac_id);
+}
+
+void rtw89_leave_lps(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_vif *rtwvif;
+
+	lockdep_assert_held(&rtwdev->mutex);
+
+	if (!test_and_clear_bit(RTW89_FLAG_LEISURE_PS, rtwdev->flags))
+		return;
+
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		rtw89_leave_lps_vif(rtwdev, rtwvif);
+}
+
+void rtw89_enter_ips(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_vif *rtwvif;
+
+	set_bit(RTW89_FLAG_INACTIVE_PS, rtwdev->flags);
+
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		rtw89_mac_vif_deinit(rtwdev, rtwvif);
+
+	rtw89_core_stop(rtwdev);
+}
+
+void rtw89_leave_ips(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_vif *rtwvif;
+	int ret;
+
+	ret = rtw89_core_start(rtwdev);
+	if (ret)
+		rtw89_err(rtwdev, "failed to leave idle state\n");
+
+	rtw89_set_channel(rtwdev);
+
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		rtw89_mac_vif_init(rtwdev, rtwvif);
+
+	clear_bit(RTW89_FLAG_INACTIVE_PS, rtwdev->flags);
+}
+
+void rtw89_set_coex_ctrl_lps(struct rtw89_dev *rtwdev, bool btc_ctrl)
+{
+	if (btc_ctrl)
+		rtw89_leave_lps(rtwdev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/ps.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/ps.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_PS_H_
+#define __RTW89_PS_H_
+
+void rtw89_enter_lps(struct rtw89_dev *rtwdev, u8 mac_id);
+void rtw89_leave_lps(struct rtw89_dev *rtwdev);
+void __rtw89_leave_ps_mode(struct rtw89_dev *rtwdev);
+void rtw89_leave_ps_mode(struct rtw89_dev *rtwdev);
+void rtw89_enter_ips(struct rtw89_dev *rtwdev);
+void rtw89_leave_ips(struct rtw89_dev *rtwdev);
+void rtw89_set_coex_ctrl_lps(struct rtw89_dev *rtwdev, bool btc_ctrl);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/reg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/reg.h
@@ -0,0 +1,2159 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_REG_H__
+#define __RTW89_REG_H__
+
+#define R_AX_SYS_WL_EFUSE_CTRL 0x000A
+#define B_AX_AUTOLOAD_SUS BIT(5)
+
+#define R_AX_SYS_FUNC_EN 0x0002
+#define B_AX_FEN_BB_GLB_RSTN BIT(1)
+#define B_AX_FEN_BBRSTB BIT(0)
+
+#define R_AX_SYS_PW_CTRL 0x0004
+#define B_AX_PSUS_OFF_CAPC_EN BIT(14)
+
+#define R_AX_SYS_CLK_CTRL 0x0008
+#define B_AX_CPU_CLK_EN BIT(14)
+
+#define R_AX_RSV_CTRL 0x001C
+#define B_AX_R_DIS_PRST BIT(6)
+#define B_AX_WLOCK_1C_BIT6 BIT(5)
+
+#define R_AX_EFUSE_CTRL_1 0x0038
+#define B_AX_EF_PGPD_MASK GENMASK(30, 28)
+#define B_AX_EF_RDT BIT(27)
+#define B_AX_EF_VDDQST_MASK GENMASK(26, 24)
+#define B_AX_EF_PGTS_MASK GENMASK(23, 20)
+#define B_AX_EF_PD_DIS BIT(11)
+#define B_AX_EF_POR BIT(10)
+#define B_AX_EF_CELL_SEL_MASK GENMASK(9, 8)
+
+#define R_AX_SPSLDO_ON_CTRL0 0x0200
+#define B_AX_OCP_L1_MASK GENMASK(15, 13)
+
+#define R_AX_EFUSE_CTRL 0x0030
+#define B_AX_EF_MODE_SEL_MASK GENMASK(31, 30)
+#define B_AX_EF_RDY BIT(29)
+#define B_AX_EF_COMP_RESULT BIT(28)
+#define B_AX_EF_ADDR_MASK GENMASK(26, 16)
+#define B_AX_EF_DATA_MASK GENMASK(15, 0)
+
+#define R_AX_GPIO_MUXCFG 0x0040
+#define B_AX_BOOT_MODE BIT(19)
+#define B_AX_WL_EECS_EXT_32K_SEL BIT(18)
+#define B_AX_WL_SEC_BONDING_OPT_STS BIT(17)
+#define B_AX_SECSIC_SEL BIT(16)
+#define B_AX_ENHTP BIT(14)
+#define B_AX_BT_AOD_GPIO3 BIT(13)
+#define B_AX_ENSIC BIT(12)
+#define B_AX_SIC_SWRST BIT(11)
+#define B_AX_PO_WIFI_PTA_PINS BIT(10)
+#define B_AX_PO_BT_PTA_PINS BIT(9)
+#define B_AX_ENUARTTX BIT(8)
+#define B_AX_BTMODE_MASK GENMASK(7, 6)
+#define MAC_AX_BT_MODE_0_3 0
+#define MAC_AX_BT_MODE_2 2
+#define B_AX_ENBT BIT(5)
+#define B_AX_EROM_EN BIT(4)
+#define B_AX_ENUARTRX BIT(2)
+#define B_AX_GPIOSEL_MASK GENMASK(1, 0)
+
+#define R_AX_DBG_CTRL 0x0058
+#define B_AX_DBG_SEL1_4BIT GENMASK(31, 30)
+#define B_AX_DBG_SEL1_16BIT BIT(27)
+#define B_AX_DBG_SEL1 GENMASK(23, 16)
+#define B_AX_DBG_SEL0_4BIT GENMASK(15, 14)
+#define B_AX_DBG_SEL0_16BIT BIT(11)
+#define B_AX_DBG_SEL0 GENMASK(7, 0)
+
+#define R_AX_SYS_SDIO_CTRL 0x0070
+#define B_AX_PCIE_DIS_L2_CTRL_LDO_HCI BIT(15)
+#define B_AX_PCIE_DIS_WLSUS_AFT_PDN BIT(14)
+#define B_AX_PCIE_AUXCLK_GATE BIT(11)
+#define B_AX_LTE_MUX_CTRL_PATH BIT(26)
+
+#define R_AX_PLATFORM_ENABLE 0x0088
+#define B_AX_WCPU_EN BIT(1)
+
+#define R_AX_SCOREBOARD  0x00AC
+#define B_AX_TOGGLE BIT(31)
+#define B_MAC_AX_SB_FW_MASK GENMASK(30, 24)
+#define B_MAC_AX_SB_DRV_MASK GENMASK(23, 0)
+#define B_MAC_AX_BTGS1_NOTIFY BIT(0)
+#define MAC_AX_NOTIFY_TP_MAJOR 0x81
+#define MAC_AX_NOTIFY_PWR_MAJOR 0x80
+
+#define R_AX_DBG_PORT_SEL 0x00C0
+#define B_AX_DEBUG_ST_MASK GENMASK(31, 0)
+
+#define R_AX_SYS_CFG1 0x00F0
+#define B_AX_CHIP_VER_MASK GENMASK(15, 12)
+
+#define R_AX_SYS_STATUS1 0x00F4
+#define B_AX_SEL_0XC0_MASK GENMASK(17, 16)
+
+#define R_AX_HALT_H2C_CTRL 0x0160
+#define R_AX_HALT_H2C 0x0168
+#define B_AX_HALT_H2C_TRIGGER BIT(0)
+#define R_AX_HALT_C2H_CTRL 0x0164
+#define R_AX_HALT_C2H 0x016C
+
+#define R_AX_WCPU_FW_CTRL 0x01E0
+#define B_AX_WCPU_FWDL_STS_MASK GENMASK(7, 5)
+#define B_AX_FWDL_PATH_RDY BIT(2)
+#define B_AX_H2C_PATH_RDY BIT(1)
+#define B_AX_WCPU_FWDL_EN BIT(0)
+
+#define R_AX_RPWM 0x01E4
+#define R_AX_PCIE_HRPWM 0x10C0
+#define PS_RPWM_TOGGLE BIT(15)
+#define PS_RPWM_ACK BIT(14)
+#define PS_RPWM_SEQ_NUM GENMASK(13, 12)
+#define PS_RPWM_STATE 0x7
+#define RPWM_SEQ_NUM_MAX 3
+#define PS_CPWM_SEQ_NUM GENMASK(13, 12)
+#define PS_CPWM_RSP_SEQ_NUM GENMASK(9, 8)
+#define PS_CPWM_STATE GENMASK(2, 0)
+#define CPWM_SEQ_NUM_MAX 3
+
+#define R_AX_BOOT_REASON 0x01E6
+#define B_AX_BOOT_REASON_MASK GENMASK(2, 0)
+
+#define R_AX_LDM 0x01E8
+#define B_AX_EN_32K BIT(31)
+
+#define R_AX_UDM0 0x01F0
+#define R_AX_UDM1 0x01F4
+#define R_AX_UDM2 0x01F8
+#define R_AX_UDM3 0x01FC
+
+#define R_AX_XTAL_ON_CTRL0 0x0280
+#define B_AX_XTAL_SC_LPS BIT(31)
+#define B_AX_XTAL_SC_XO_MASK GENMASK(23, 17)
+#define B_AX_XTAL_SC_XI_MASK GENMASK(16, 10)
+#define B_AX_XTAL_SC_MASK GENMASK(6, 0)
+
+#define R_AX_GPIO0_7_FUNC_SEL 0x02D0
+
+#define R_AX_WLRF_CTRL 0x02F0
+#define B_AX_WLRF1_CTRL_7 BIT(15)
+#define B_AX_WLRF1_CTRL_1 BIT(9)
+#define B_AX_WLRF_CTRL_7 BIT(7)
+#define B_AX_WLRF_CTRL_1 BIT(1)
+
+#define R_AX_IC_PWR_STATE 0x03F0
+#define B_AX_WHOLE_SYS_PWR_STE_MASK GENMASK(25, 16)
+#define B_AX_WLMAC_PWR_STE_MASK GENMASK(9, 8)
+#define B_AX_UART_HCISYS_PWR_STE_MASK GENMASK(7, 6)
+#define B_AX_SDIO_HCISYS_PWR_STE_MASK GENMASK(5, 4)
+#define B_AX_USB_HCISYS_PWR_STE_MASK GENMASK(3, 2)
+#define B_AX_PCIE_HCISYS_PWR_STE_MASK GENMASK(1, 0)
+
+#define R_AX_FILTER_MODEL_ADDR 0x0C04
+
+#define R_AX_PCIE_DBG_CTRL 0x11C0
+#define B_AX_DBG_DUMMY_MASK GENMASK(23, 16)
+#define B_AX_DBG_SEL_MASK GENMASK(15, 13)
+#define B_AX_PCIE_DBG_SEL BIT(12)
+#define B_AX_MRD_TIMEOUT_EN BIT(10)
+#define B_AX_ASFF_FULL_NO_STK BIT(1)
+#define B_AX_EN_STUCK_DBG BIT(0)
+
+#define R_AX_PHYREG_SET 0x8040
+#define PHYREG_SET_ALL_CYCLE 0x8
+
+#define R_AX_HD0IMR 0x8110
+#define B_AX_WDT_PTFM_INT_EN BIT(5)
+#define B_AX_CPWM_INT_EN BIT(2)
+#define B_AX_GT3_INT_EN BIT(1)
+#define B_AX_C2H_INT_EN BIT(0)
+#define R_AX_HD0ISR 0x8114
+#define B_AX_C2H_INT BIT(0)
+
+#define R_AX_H2CREG_DATA0 0x8140
+#define R_AX_H2CREG_DATA1 0x8144
+#define R_AX_H2CREG_DATA2 0x8148
+#define R_AX_H2CREG_DATA3 0x814C
+#define R_AX_C2HREG_DATA0 0x8150
+#define R_AX_C2HREG_DATA1 0x8154
+#define R_AX_C2HREG_DATA2 0x8158
+#define R_AX_C2HREG_DATA3 0x815C
+#define R_AX_H2CREG_CTRL 0x8160
+#define B_AX_H2CREG_TRIGGER BIT(0)
+#define R_AX_C2HREG_CTRL 0x8164
+#define B_AX_C2HREG_TRIGGER BIT(0)
+#define R_AX_CPWM 0x8170
+
+#define R_AX_HCI_FUNC_EN 0x8380
+#define B_AX_HCI_RXDMA_EN BIT(1)
+#define B_AX_HCI_TXDMA_EN BIT(0)
+
+#define R_AX_BOOT_DBG 0x83F0
+
+#define R_AX_DMAC_FUNC_EN 0x8400
+#define B_AX_MAC_FUNC_EN BIT(30)
+#define B_AX_DMAC_FUNC_EN BIT(29)
+#define B_AX_MPDU_PROC_EN BIT(28)
+#define B_AX_WD_RLS_EN BIT(27)
+#define B_AX_DLE_WDE_EN BIT(26)
+#define B_AX_TXPKT_CTRL_EN BIT(25)
+#define B_AX_STA_SCH_EN BIT(24)
+#define B_AX_DLE_PLE_EN BIT(23)
+#define B_AX_PKT_BUF_EN BIT(22)
+#define B_AX_DMAC_TBL_EN BIT(21)
+#define B_AX_PKT_IN_EN BIT(20)
+#define B_AX_DLE_CPUIO_EN BIT(19)
+#define B_AX_DISPATCHER_EN BIT(18)
+#define B_AX_MAC_SEC_EN BIT(16)
+
+#define R_AX_DMAC_CLK_EN 0x8404
+#define B_AX_WD_RLS_CLK_EN BIT(27)
+#define B_AX_DLE_WDE_CLK_EN BIT(26)
+#define B_AX_TXPKT_CTRL_CLK_EN BIT(25)
+#define B_AX_STA_SCH_CLK_EN BIT(24)
+#define B_AX_DLE_PLE_CLK_EN BIT(23)
+#define B_AX_PKT_IN_CLK_EN BIT(20)
+#define B_AX_DLE_CPUIO_CLK_EN BIT(19)
+#define B_AX_DISPATCHER_CLK_EN BIT(18)
+#define B_AX_MAC_SEC_CLK_EN BIT(16)
+
+#define PCI_LTR_IDLE_TIMER_1US 0
+#define PCI_LTR_IDLE_TIMER_10US 1
+#define PCI_LTR_IDLE_TIMER_100US 2
+#define PCI_LTR_IDLE_TIMER_200US 3
+#define PCI_LTR_IDLE_TIMER_400US 4
+#define PCI_LTR_IDLE_TIMER_800US 5
+#define PCI_LTR_IDLE_TIMER_1_6MS 6
+#define PCI_LTR_IDLE_TIMER_3_2MS 7
+#define PCI_LTR_IDLE_TIMER_R_ERR 0xFD
+#define PCI_LTR_IDLE_TIMER_DEF 0xFE
+#define PCI_LTR_IDLE_TIMER_IGNORE 0xFF
+
+#define PCI_LTR_SPC_10US 0
+#define PCI_LTR_SPC_100US 1
+#define PCI_LTR_SPC_500US 2
+#define PCI_LTR_SPC_1MS 3
+#define PCI_LTR_SPC_R_ERR 0xFD
+#define PCI_LTR_SPC_DEF 0xFE
+#define PCI_LTR_SPC_IGNORE 0xFF
+
+#define R_AX_LTR_CTRL_0 0x8410
+#define B_AX_LTR_SPACE_IDX_MASK GENMASK(13, 12)
+#define B_AX_LTR_IDLE_TIMER_IDX_MASK GENMASK(10, 8)
+#define B_AX_APP_LTR_ACT BIT(5)
+#define B_AX_APP_LTR_IDLE BIT(4)
+#define B_AX_LTR_EN BIT(1)
+#define B_AX_LTR_HW_EN BIT(0)
+
+#define R_AX_LTR_CTRL_1 0x8414
+#define B_AX_LTR_RX1_TH_MASK GENMASK(27, 16)
+#define B_AX_LTR_RX0_TH_MASK GENMASK(11, 0)
+
+#define R_AX_LTR_IDLE_LATENCY 0x8418
+
+#define R_AX_LTR_ACTIVE_LATENCY 0x841C
+
+#define R_AX_SER_DBG_INFO 0x8424
+#define B_AX_L0_TO_L1_EVENT_MASK GENMASK(31, 28)
+
+#define R_AX_DLE_EMPTY0 0x8430
+#define B_AX_PLE_EMPTY_QTA_DMAC_CPUIO BIT(26)
+#define B_AX_PLE_EMPTY_QTA_DMAC_MPDU_TX BIT(25)
+#define B_AX_PLE_EMPTY_QTA_DMAC_WLAN_CPU BIT(24)
+#define B_AX_PLE_EMPTY_QTA_DMAC_H2C BIT(23)
+#define B_AX_PLE_EMPTY_QTA_DMAC_B1_TXPL BIT(22)
+#define B_AX_PLE_EMPTY_QTA_DMAC_B0_TXPL BIT(21)
+#define B_AX_WDE_EMPTY_QTA_DMAC_CPUIO BIT(20)
+#define B_AX_WDE_EMPTY_QTA_DMAC_PKTIN BIT(19)
+#define B_AX_WDE_EMPTY_QTA_DMAC_DATA_CPU BIT(18)
+#define B_AX_WDE_EMPTY_QTA_DMAC_WLAN_CPU BIT(17)
+#define B_AX_WDE_EMPTY_QTA_DMAC_HIF BIT(16)
+#define B_AX_WDE_EMPTY_QUE_DMAC_PKTIN BIT(10)
+#define B_AX_PLE_EMPTY_QUE_DMAC_SEC_TX BIT(9)
+#define B_AX_PLE_EMPTY_QUE_DMAC_MPDU_TX BIT(8)
+#define B_AX_WDE_EMPTY_QUE_OTHERS BIT(7)
+#define B_AX_WDE_EMPTY_QUE_CMAC0_WMM1 BIT(4)
+#define B_AX_WDE_EMPTY_QUE_CMAC0_WMM0 BIT(3)
+#define B_AX_WDE_EMPTY_QUE_CMAC1_MBH BIT(2)
+#define B_AX_WDE_EMPTY_QUE_CMAC0_MBH BIT(1)
+#define B_AX_WDE_EMPTY_QUE_CMAC0_ALL_AC BIT(0)
+
+#define R_AX_DMAC_ERR_ISR 0x8524
+#define B_AX_DLE_CPUIO_ERR_FLAG BIT(10)
+#define B_AX_APB_BRIDGE_ERR_FLAG BIT(9)
+#define B_AX_DISPATCH_ERR_FLAG BIT(8)
+#define B_AX_PKTIN_ERR_FLAG BIT(7)
+#define B_AX_PLE_DLE_ERR_FLAG BIT(6)
+#define B_AX_TXPKTCTRL_ERR_FLAG BIT(5)
+#define B_AX_WDE_DLE_ERR_FLAG BIT(4)
+#define B_AX_STA_SCHEDULER_ERR_FLAG BIT(3)
+#define B_AX_MPDU_ERR_FLAG BIT(2)
+#define B_AX_WSEC_ERR_FLAG BIT(1)
+#define B_AX_WDRLS_ERR_FLAG BIT(0)
+
+#define R_AX_DISPATCHER_GLOBAL_SETTING_0 0x8800
+#define B_AX_PL_PAGE_128B_SEL BIT(9)
+#define B_AX_WD_PAGE_64B_SEL BIT(8)
+#define R_AX_OTHER_DISPATCHER_ERR_ISR 0x8804
+#define R_AX_HOST_DISPATCHER_ERR_ISR 0x8808
+#define R_AX_CPU_DISPATCHER_ERR_ISR 0x880C
+#define R_AX_TX_ADDRESS_INFO_MODE_SETTING 0x8810
+#define B_AX_HOST_ADDR_INFO_8B_SEL BIT(0)
+
+#define R_AX_HOST_DISPATCHER_ERR_IMR 0x8850
+#define B_AX_HDT_OFFSET_UNMATCH_INT_EN BIT(7)
+#define B_AX_HDT_PKT_FAIL_DBG_INT_EN BIT(2)
+
+#define R_AX_CPU_DISPATCHER_ERR_IMR 0x8854
+#define B_AX_CPU_SHIFT_EN_ERR_INT_EN BIT(25)
+
+#define R_AX_OTHER_DISPATCHER_ERR_IMR 0x8858
+
+#define R_AX_HCI_FC_CTRL 0x8A00
+#define B_AX_HCI_FC_CH12_FULL_COND_MASK GENMASK(11, 10)
+#define B_AX_HCI_FC_WP_CH811_FULL_COND_MASK GENMASK(9, 8)
+#define B_AX_HCI_FC_WP_CH07_FULL_COND_MASK GENMASK(7, 6)
+#define B_AX_HCI_FC_WD_FULL_COND_MASK GENMASK(5, 4)
+#define B_AX_HCI_FC_CH12_EN BIT(3)
+#define B_AX_HCI_FC_MODE_MASK GENMASK(2, 1)
+#define B_AX_HCI_FC_EN BIT(0)
+
+#define R_AX_CH_PAGE_CTRL 0x8A04
+#define B_AX_PREC_PAGE_CH12_MASK GENMASK(24, 16)
+#define B_AX_PREC_PAGE_CH011_MASK GENMASK(8, 0)
+
+#define B_AX_MAX_PG_MASK GENMASK(28, 16)
+#define B_AX_MIN_PG_MASK GENMASK(12, 0)
+#define B_AX_GRP BIT(31)
+#define R_AX_ACH0_PAGE_CTRL 0x8A10
+#define R_AX_ACH1_PAGE_CTRL 0x8A14
+#define R_AX_ACH2_PAGE_CTRL 0x8A18
+#define R_AX_ACH3_PAGE_CTRL 0x8A1C
+#define R_AX_ACH4_PAGE_CTRL 0x8A20
+#define R_AX_ACH5_PAGE_CTRL 0x8A24
+#define R_AX_ACH6_PAGE_CTRL 0x8A28
+#define R_AX_ACH7_PAGE_CTRL 0x8A2C
+#define R_AX_CH8_PAGE_CTRL 0x8A30
+#define R_AX_CH9_PAGE_CTRL 0x8A34
+#define R_AX_CH10_PAGE_CTRL 0x8A38
+#define R_AX_CH11_PAGE_CTRL 0x8A3C
+
+#define B_AX_AVAL_PG_MASK GENMASK(27, 16)
+#define B_AX_USE_PG_MASK GENMASK(12, 0)
+#define R_AX_ACH0_PAGE_INFO 0x8A50
+#define R_AX_ACH1_PAGE_INFO 0x8A54
+#define R_AX_ACH2_PAGE_INFO 0x8A58
+#define R_AX_ACH3_PAGE_INFO 0x8A5C
+#define R_AX_ACH4_PAGE_INFO 0x8A60
+#define R_AX_ACH5_PAGE_INFO 0x8A64
+#define R_AX_ACH6_PAGE_INFO 0x8A68
+#define R_AX_ACH7_PAGE_INFO 0x8A6C
+#define R_AX_CH8_PAGE_INFO 0x8A70
+#define R_AX_CH9_PAGE_INFO 0x8A74
+#define R_AX_CH10_PAGE_INFO 0x8A78
+#define R_AX_CH11_PAGE_INFO 0x8A7C
+#define R_AX_CH12_PAGE_INFO 0x8A80
+
+#define R_AX_PUB_PAGE_INFO3 0x8A8C
+#define B_AX_G1_AVAL_PG_MASK GENMASK(28, 16)
+#define B_AX_G0_AVAL_PG_MASK GENMASK(12, 0)
+
+#define R_AX_PUB_PAGE_CTRL1 0x8A90
+#define B_AX_PUBPG_G1_MASK GENMASK(28, 16)
+#define B_AX_PUBPG_G0_MASK GENMASK(12, 0)
+
+#define R_AX_PUB_PAGE_CTRL2 0x8A94
+#define B_AX_PUBPG_ALL_MASK GENMASK(12, 0)
+
+#define R_AX_PUB_PAGE_INFO1 0x8A98
+#define B_AX_G1_USE_PG_MASK GENMASK(28, 16)
+#define B_AX_G0_USE_PG_MASK GENMASK(12, 0)
+
+#define R_AX_PUB_PAGE_INFO2 0x8A9C
+#define B_AX_PUB_AVAL_PG_MASK GENMASK(12, 0)
+
+#define R_AX_WP_PAGE_CTRL1 0x8AA0
+#define B_AX_PREC_PAGE_WP_CH811_MASK GENMASK(24, 16)
+#define B_AX_PREC_PAGE_WP_CH07_MASK GENMASK(8, 0)
+
+#define R_AX_WP_PAGE_CTRL2 0x8AA4
+#define B_AX_WP_THRD_MASK GENMASK(12, 0)
+
+#define R_AX_WP_PAGE_INFO1 0x8AA8
+#define B_AX_WP_AVAL_PG_MASK GENMASK(28, 16)
+
+#define R_AX_WDE_PKTBUF_CFG 0x8C08
+#define B_AX_WDE_START_BOUND_MASK GENMASK(13, 8)
+#define B_AX_WDE_PAGE_SEL_MASK GENMASK(1, 0)
+#define B_AX_WDE_FREE_PAGE_NUM_MASK GENMASK(28, 16)
+#define R_AX_WDE_ERR_FLAG_CFG 0x8C34
+#define R_AX_WDE_ERR_IMR 0x8C38
+#define R_AX_WDE_ERR_ISR 0x8C3C
+
+#define B_AX_WDE_MAX_SIZE_MASK GENMASK(27, 16)
+#define B_AX_WDE_MIN_SIZE_MASK GENMASK(11, 0)
+#define R_AX_WDE_QTA0_CFG 0x8C40
+#define R_AX_WDE_QTA1_CFG 0x8C44
+#define R_AX_WDE_QTA2_CFG 0x8C48
+#define R_AX_WDE_QTA3_CFG 0x8C4C
+#define R_AX_WDE_QTA4_CFG 0x8C50
+
+#define B_AX_DLE_PUB_PGNUM GENMASK(12, 0)
+#define B_AX_DLE_FREE_HEADPG GENMASK(11, 0)
+#define B_AX_DLE_FREE_TAILPG GENMASK(27, 16)
+#define B_AX_DLE_USE_PGNUM GENMASK(27, 16)
+#define B_AX_DLE_RSV_PGNUM GENMASK(11, 0)
+#define B_AX_DLE_QEMPTY_GRP GENMASK(31, 0)
+
+#define R_AX_WDE_INI_STATUS 0x8D00
+#define B_AX_WDE_Q_MGN_INI_RDY BIT(1)
+#define B_AX_WDE_BUF_MGN_INI_RDY BIT(0)
+#define WDE_MGN_INI_RDY (B_AX_WDE_Q_MGN_INI_RDY | B_AX_WDE_BUF_MGN_INI_RDY)
+#define R_AX_WDE_DBG_FUN_INTF_CTL 0x8D10
+#define B_AX_WDE_DFI_ACTIVE BIT(31)
+#define B_AX_WDE_DFI_TRGSEL_MASK GENMASK(19, 16)
+#define B_AX_WDE_DFI_ADDR_MASK GENMASK(15, 0)
+#define R_AX_WDE_DBG_FUN_INTF_DATA 0x8D14
+#define B_AX_WDE_DFI_DATA_MASK GENMASK(31, 0)
+
+#define R_AX_PLE_PKTBUF_CFG 0x9008
+#define B_AX_PLE_START_BOUND_MASK GENMASK(13, 8)
+#define B_AX_PLE_PAGE_SEL_MASK GENMASK(1, 0)
+#define B_AX_PLE_FREE_PAGE_NUM_MASK GENMASK(28, 16)
+#define R_AX_PLE_ERR_FLAG_CFG 0x9034
+
+#define R_AX_PLE_ERR_IMR 0x9038
+#define B_AX_PLE_GETNPG_STRPG_ERR_INT_EN BIT(5)
+
+#define R_AX_PLE_ERR_FLAG_ISR 0x903C
+#define B_AX_PLE_MAX_SIZE_MASK GENMASK(27, 16)
+#define B_AX_PLE_MIN_SIZE_MASK GENMASK(11, 0)
+#define R_AX_PLE_QTA0_CFG 0x9040
+#define R_AX_PLE_QTA1_CFG 0x9044
+#define R_AX_PLE_QTA2_CFG 0x9048
+#define R_AX_PLE_QTA3_CFG 0x904C
+#define R_AX_PLE_QTA4_CFG 0x9050
+#define R_AX_PLE_QTA5_CFG 0x9054
+#define R_AX_PLE_QTA6_CFG 0x9058
+#define B_AX_PLE_Q6_MAX_SIZE_MASK GENMASK(27, 16)
+#define B_AX_PLE_Q6_MIN_SIZE_MASK GENMASK(11, 0)
+#define R_AX_PLE_QTA7_CFG 0x905C
+#define R_AX_PLE_QTA8_CFG 0x9060
+#define R_AX_PLE_QTA9_CFG 0x9064
+#define R_AX_PLE_QTA10_CFG 0x9068
+
+#define R_AX_PLE_INI_STATUS 0x9100
+#define B_AX_PLE_Q_MGN_INI_RDY BIT(1)
+#define B_AX_PLE_BUF_MGN_INI_RDY BIT(0)
+#define PLE_MGN_INI_RDY (B_AX_PLE_Q_MGN_INI_RDY | B_AX_PLE_BUF_MGN_INI_RDY)
+#define R_AX_PLE_DBG_FUN_INTF_CTL 0x9110
+#define B_AX_PLE_DFI_ACTIVE BIT(31)
+#define B_AX_PLE_DFI_TRGSEL_MASK GENMASK(19, 16)
+#define B_AX_PLE_DFI_ADDR_MASK GENMASK(15, 0)
+#define R_AX_PLE_DBG_FUN_INTF_DATA 0x9114
+#define B_AX_PLE_DFI_DATA_MASK GENMASK(31, 0)
+
+#define R_AX_WDRLS_CFG 0x9408
+#define B_AX_RLSRPT_BUFREQ_TO_MASK GENMASK(15, 8)
+#define B_AX_WDRLS_MODE_MASK GENMASK(1, 0)
+
+#define R_AX_RLSRPT0_CFG0 0x9410
+#define B_AX_RLSRPT0_FLTR_MAP_MASK GENMASK(27, 24)
+#define B_AX_RLSRPT0_PKTTYPE_MASK GENMASK(19, 16)
+#define B_AX_RLSRPT0_PID_MASK GENMASK(10, 8)
+#define B_AX_RLSRPT0_QID_MASK GENMASK(5, 0)
+
+#define R_AX_RLSRPT0_CFG1 0x9414
+#define B_AX_RLSRPT0_TO_MASK GENMASK(23, 16)
+#define B_AX_RLSRPT0_AGGNUM_MASK GENMASK(7, 0)
+
+#define R_AX_WDRLS_ERR_IMR 0x9430
+#define B_AX_WDRLS_RPT1_FRZTO_ERR_INT_EN BIT(13)
+#define B_AX_WDRLS_RPT1_AGGNUM0_ERR_INT_EN BIT(12)
+#define B_AX_WDRLS_RPT0_FRZTO_ERR_INT_EN BIT(9)
+#define B_AX_WDRLS_RPT0_AGGNUM0_ERR_INT_EN BIT(8)
+#define B_AX_WDRLS_PLEBREQ_PKTID_ISNULL_ERR_INT_EN BIT(5)
+#define B_AX_WDRLS_PLEBREQ_TO_ERR_INT_EN BIT(4)
+#define B_AX_WDRLS_CTL_FRZTO_ERR_INT_EN BIT(2)
+#define B_AX_WDRLS_CTL_PLPKTID_ISNULL_ERR_INT_EN BIT(1)
+#define B_AX_WDRLS_CTL_WDPKTID_ISNULL_ERR_INT_EN BIT(0)
+#define R_AX_WDRLS_ERR_ISR 0x9434
+
+#define R_AX_BBRPT_COM_ERR_IMR_ISR 0x960C
+#define R_AX_BBRPT_CHINFO_ERR_IMR_ISR 0x962C
+#define R_AX_BBRPT_DFS_ERR_IMR_ISR 0x963C
+#define R_AX_LA_ERRFLAG 0x966C
+
+#define R_AX_WD_BUF_REQ 0x9800
+#define R_AX_PL_BUF_REQ 0x9820
+#define B_AX_WD_BUF_REQ_EXEC BIT(31)
+#define B_AX_WD_BUF_REQ_QUOTA_ID_MASK GENMASK(23, 16)
+#define B_AX_WD_BUF_REQ_LEN_MASK GENMASK(15, 0)
+
+#define R_AX_WD_BUF_STATUS 0x9804
+#define R_AX_PL_BUF_STATUS 0x9824
+#define B_AX_WD_BUF_STAT_DONE BIT(31)
+#define B_AX_WD_BUF_STAT_PKTID_MASK GENMASK(11, 0)
+
+#define R_AX_WD_CPUQ_OP_0 0x9810
+#define R_AX_PL_CPUQ_OP_0 0x9830
+#define B_AX_WD_CPUQ_OP_EXEC BIT(31)
+#define B_AX_CPUQ_OP_CMD_TYPE_MASK GENMASK(27, 24)
+#define B_AX_CPUQ_OP_MACID_MASK GENMASK(23, 16)
+#define B_AX_CPUQ_OP_PKTNUM_MASK GENMASK(7, 0)
+
+#define R_AX_WD_CPUQ_OP_1 0x9814
+#define R_AX_PL_CPUQ_OP_1 0x9834
+#define B_AX_CPUQ_OP_SRC_PID_MASK GENMASK(24, 22)
+#define B_AX_CPUQ_OP_SRC_QID_MASK GENMASK(21, 16)
+#define B_AX_CPUQ_OP_DST_PID_MASK GENMASK(8, 6)
+#define B_AX_CPUQ_OP_DST_QID_MASK GENMASK(5, 0)
+
+#define R_AX_WD_CPUQ_OP_2 0x9818
+#define R_AX_PL_CPUQ_OP_2 0x9838
+#define B_AX_WD_CPUQ_OP_STRT_PKTID_MASK GENMASK(27, 16)
+#define B_AX_WD_CPUQ_OP_END_PKTID_MASK GENMASK(11, 0)
+
+#define R_AX_WD_CPUQ_OP_STATUS 0x981C
+#define R_AX_PL_CPUQ_OP_STATUS 0x983C
+#define B_AX_WD_CPUQ_OP_STAT_DONE BIT(31)
+#define B_AX_WD_CPUQ_OP_PKTID_MASK GENMASK(11, 0)
+#define R_AX_CPUIO_ERR_IMR 0x9840
+#define R_AX_CPUIO_ERR_ISR 0x9844
+
+#define R_AX_SEC_ERR_IMR_ISR 0x991C
+
+#define R_AX_PKTIN_SETTING 0x9A00
+#define B_AX_WD_ADDR_INFO_LENGTH BIT(1)
+#define R_AX_PKTIN_ERR_IMR 0x9A20
+#define R_AX_PKTIN_ERR_ISR 0x9A24
+
+#define R_AX_MPDU_TX_ERR_ISR 0x9BF0
+#define R_AX_MPDU_TX_ERR_IMR 0x9BF4
+
+#define R_AX_MPDU_PROC 0x9C00
+#define B_AX_A_ICV_ERR BIT(1)
+#define B_AX_APPEND_FCS BIT(0)
+
+#define R_AX_ACTION_FWD0 0x9C04
+#define TRXCFG_MPDU_PROC_ACT_FRWD 0x02A95A95
+
+#define R_AX_TF_FWD 0x9C14
+#define TRXCFG_MPDU_PROC_TF_FRWD 0x0000AA55
+
+#define R_AX_HW_RPT_FWD 0x9C18
+#define B_AX_FWD_PPDU_STAT_MASK GENMASK(1, 0)
+#define RTW89_PRPT_DEST_HOST 1
+#define RTW89_PRPT_DEST_WLCPU 2
+
+#define R_AX_CUT_AMSDU_CTRL 0x9C40
+#define TRXCFG_MPDU_PROC_CUT_CTRL	0x010E05F0
+
+#define R_AX_MPDU_RX_ERR_ISR 0x9CF0
+#define R_AX_MPDU_RX_ERR_IMR 0x9CF4
+
+#define R_AX_SEC_ENG_CTRL 0x9D00
+#define B_AX_TX_PARTIAL_MODE BIT(11)
+#define B_AX_CLK_EN_CGCMP BIT(10)
+#define B_AX_CLK_EN_WAPI BIT(9)
+#define B_AX_CLK_EN_WEP_TKIP BIT(8)
+#define B_AX_BMC_MGNT_DEC BIT(5)
+#define B_AX_UC_MGNT_DEC BIT(4)
+#define B_AX_MC_DEC BIT(3)
+#define B_AX_BC_DEC BIT(2)
+#define B_AX_SEC_RX_DEC BIT(1)
+#define B_AX_SEC_TX_ENC BIT(0)
+
+#define R_AX_SEC_MPDU_PROC 0x9D04
+#define B_AX_APPEND_ICV BIT(1)
+#define B_AX_APPEND_MIC BIT(0)
+
+#define R_AX_SEC_CAM_ACCESS 0x9D10
+#define R_AX_SEC_CAM_RDATA 0x9D14
+#define R_AX_SEC_CAM_WDATA 0x9D18
+#define R_AX_SEC_DEBUG 0x9D1C
+#define R_AX_SEC_TX_DEBUG 0x9D20
+#define R_AX_SEC_RX_DEBUG 0x9D24
+#define R_AX_SEC_TRX_PKT_CNT 0x9D28
+#define R_AX_SEC_TRX_BLK_CNT 0x9D2C
+
+#define R_AX_SS_CTRL 0x9E10
+#define B_AX_SS_INIT_DONE_1 BIT(31)
+#define B_AX_SS_WARM_INIT_FLG BIT(29)
+#define B_AX_SS_EN BIT(0)
+
+#define R_AX_SS_MACID_PAUSE_0 0x9EB0
+#define B_AX_SS_MACID31_0_PAUSE_SH 0
+#define B_AX_SS_MACID31_0_PAUSE_MASK GENMASK(31, 0)
+
+#define R_AX_SS_MACID_PAUSE_1 0x9EB4
+#define B_AX_SS_MACID63_32_PAUSE_SH 0
+#define B_AX_SS_MACID63_32_PAUSE_MASK GENMASK(31, 0)
+
+#define R_AX_SS_MACID_PAUSE_2 0x9EB8
+#define B_AX_SS_MACID95_64_PAUSE_SH 0
+#define B_AX_SS_MACID95_64_PAUSE_MASK GENMASK(31, 0)
+
+#define R_AX_SS_MACID_PAUSE_3 0x9EBC
+#define B_AX_SS_MACID127_96_PAUSE_SH 0
+#define B_AX_SS_MACID127_96_PAUSE_MASK GENMASK(31, 0)
+
+#define R_AX_STA_SCHEDULER_ERR_IMR 0x9EF0
+#define R_AX_STA_SCHEDULER_ERR_ISR 0x9EF4
+
+#define R_AX_TXPKTCTL_ERR_IMR_ISR 0x9F1C
+#define R_AX_TXPKTCTL_ERR_IMR_ISR_B1 0x9F2C
+#define B_AX_TXPKTCTL_CMDPSR_FRZTO_ERR_INT_EN BIT(9)
+#define B_AX_TXPKTCTL_USRCTL_RLSBMPLEN_ERR_INT_EN BIT(3)
+#define B_AX_TXPKTCTL_USRCTL_RDNRLSCMD_ERR_INT_EN BIT(2)
+#define B_AX_TXPKTCTL_USRCTL_NOINIT_ERR_INT_EN BIT(1)
+
+#define R_AX_DBG_FUN_INTF_CTL 0x9F30
+#define B_AX_DFI_ACTIVE BIT(31)
+#define B_AX_DFI_TRGSEL_MASK GENMASK(19, 16)
+#define B_AX_DFI_ADDR_MASK GENMASK(15, 0)
+#define R_AX_DBG_FUN_INTF_DATA 0x9F34
+#define B_AX_DFI_DATA_MASK GENMASK(31, 0)
+
+#define R_AX_AFE_CTRL1 0x0024
+
+#define B_AX_R_SYM_WLCMAC1_P4_PC_EN BIT(4)
+#define B_AX_R_SYM_WLCMAC1_P3_PC_EN BIT(3)
+#define B_AX_R_SYM_WLCMAC1_P2_PC_EN BIT(2)
+#define B_AX_R_SYM_WLCMAC1_P1_PC_EN BIT(1)
+#define B_AX_R_SYM_WLCMAC1_PC_EN BIT(0)
+
+#define R_AX_SYS_ISO_CTRL_EXTEND 0x0080
+#define B_AX_CMAC1_FEN BIT(30)
+#define B_AX_R_SYM_FEN_WLBBGLB_1 BIT(17)
+#define B_AX_R_SYM_FEN_WLBBFUN_1 BIT(16)
+#define B_AX_R_SYM_ISO_CMAC12PP BIT(5)
+
+#define R_AX_CMAC_REG_START 0xC000
+
+#define R_AX_CMAC_FUNC_EN 0xC000
+#define R_AX_CMAC_FUNC_EN_C1 0xE000
+#define B_AX_CMAC_CRPRT BIT(31)
+#define B_AX_CMAC_EN BIT(30)
+#define B_AX_CMAC_TXEN BIT(29)
+#define B_AX_CMAC_RXEN BIT(28)
+#define B_AX_FORCE_CMACREG_GCKEN BIT(15)
+#define B_AX_PHYINTF_EN BIT(5)
+#define B_AX_CMAC_DMA_EN BIT(4)
+#define B_AX_PTCLTOP_EN BIT(3)
+#define B_AX_SCHEDULER_EN BIT(2)
+#define B_AX_TMAC_EN BIT(1)
+#define B_AX_RMAC_EN BIT(0)
+
+#define R_AX_CK_EN 0xC004
+#define R_AX_CK_EN_C1 0xE004
+#define B_AX_CMAC_ALLCKEN GENMASK(31, 0)
+#define B_AX_CMAC_CKEN BIT(30)
+#define B_AX_PHYINTF_CKEN BIT(5)
+#define B_AX_CMAC_DMA_CKEN BIT(4)
+#define B_AX_PTCLTOP_CKEN BIT(3)
+#define B_AX_SCHEDULER_CKEN BIT(2)
+#define B_AX_TMAC_CKEN BIT(1)
+#define B_AX_RMAC_CKEN BIT(0)
+
+#define R_AX_WMAC_RFMOD 0xC010
+#define R_AX_WMAC_RFMOD_C1 0xE010
+#define B_AX_WMAC_RFMOD_MASK GENMASK(1, 0)
+
+#define R_AX_GID_POSITION0 0xC070
+#define R_AX_GID_POSITION0_C1 0xE070
+#define R_AX_GID_POSITION1 0xC074
+#define R_AX_GID_POSITION1_C1 0xE074
+#define R_AX_GID_POSITION2 0xC078
+#define R_AX_GID_POSITION2_C1 0xE078
+#define R_AX_GID_POSITION3 0xC07C
+#define R_AX_GID_POSITION3_C1 0xE07C
+#define R_AX_GID_POSITION_EN0 0xC080
+#define R_AX_GID_POSITION_EN0_C1 0xE080
+#define R_AX_GID_POSITION_EN1 0xC084
+#define R_AX_GID_POSITION_EN1_C1 0xE084
+
+#define R_AX_TX_SUB_CARRIER_VALUE 0xC088
+#define R_AX_TX_SUB_CARRIER_VALUE_C1 0xE088
+#define B_AX_TXSC_80M_MASK GENMASK(11, 8)
+#define B_AX_TXSC_40M_MASK GENMASK(7, 4)
+#define B_AX_TXSC_20M_MASK GENMASK(3, 0)
+
+#define R_AX_CMAC_ERR_ISR 0xC164
+#define R_AX_CMAC_ERR_ISR_C1 0xE164
+#define B_AX_WMAC_TX_ERR_IND BIT(7)
+#define B_AX_WMAC_RX_ERR_IND BIT(6)
+#define B_AX_TXPWR_CTRL_ERR_IND BIT(5)
+#define B_AX_PHYINTF_ERR_IND BIT(4)
+#define B_AX_DMA_TOP_ERR_IND BIT(3)
+#define B_AX_PTCL_TOP_ERR_IND BIT(1)
+#define B_AX_SCHEDULE_TOP_ERR_IND BIT(0)
+
+#define R_AX_MACID_SLEEP_0 0xC2C0
+#define R_AX_MACID_SLEEP_0_C1 0xE2C0
+#define B_AX_MACID31_0_SLEEP_SH 0
+#define B_AX_MACID31_0_SLEEP_MASK GENMASK(31, 0)
+
+#define R_AX_MACID_SLEEP_1 0xC2C4
+#define R_AX_MACID_SLEEP_1_C1 0xE2C4
+#define B_AX_MACID63_32_SLEEP_SH 0
+#define B_AX_MACID63_32_SLEEP_MASK GENMASK(31, 0)
+
+#define R_AX_MACID_SLEEP_2 0xC2C8
+#define R_AX_MACID_SLEEP_2_C1 0xE2C8
+#define B_AX_MACID95_64_SLEEP_SH 0
+#define B_AX_MACID95_64_SLEEP_MASK GENMASK(31, 0)
+
+#define R_AX_MACID_SLEEP_3 0xC2CC
+#define R_AX_MACID_SLEEP_3_C1 0xE2CC
+#define B_AX_MACID127_96_SLEEP_SH 0
+#define B_AX_MACID127_96_SLEEP_MASK GENMASK(31, 0)
+
+#define SCH_PREBKF_24US 0x18
+#define R_AX_PREBKF_CFG_0 0xC338
+#define R_AX_PREBKF_CFG_0_C1 0xE338
+#define B_AX_PREBKF_TIME_MASK GENMASK(4, 0)
+
+#define R_AX_CCA_CFG_0 0xC340
+#define R_AX_CCA_CFG_0_C1 0xE340
+#define B_AX_BTCCA_BRK_TXOP_EN BIT(9)
+#define B_AX_BTCCA_EN BIT(5)
+#define B_AX_EDCCA_EN BIT(4)
+#define B_AX_SEC80_EN BIT(3)
+#define B_AX_SEC40_EN BIT(2)
+#define B_AX_SEC20_EN BIT(1)
+#define B_AX_CCA_EN BIT(0)
+
+#define R_AX_CTN_TXEN 0xC348
+#define R_AX_CTN_TXEN_C1 0xE348
+#define B_AX_CTN_TXEN_TWT_1 BIT(15)
+#define B_AX_CTN_TXEN_TWT_0 BIT(14)
+#define B_AX_CTN_TXEN_ULQ BIT(13)
+#define B_AX_CTN_TXEN_BCNQ BIT(12)
+#define B_AX_CTN_TXEN_HGQ BIT(11)
+#define B_AX_CTN_TXEN_CPUMGQ BIT(10)
+#define B_AX_CTN_TXEN_MGQ1 BIT(9)
+#define B_AX_CTN_TXEN_MGQ BIT(8)
+#define B_AX_CTN_TXEN_VO_1 BIT(7)
+#define B_AX_CTN_TXEN_VI_1 BIT(6)
+#define B_AX_CTN_TXEN_BK_1 BIT(5)
+#define B_AX_CTN_TXEN_BE_1 BIT(4)
+#define B_AX_CTN_TXEN_VO_0 BIT(3)
+#define B_AX_CTN_TXEN_VI_0 BIT(2)
+#define B_AX_CTN_TXEN_BK_0 BIT(1)
+#define B_AX_CTN_TXEN_BE_0 BIT(0)
+
+#define R_AX_MUEDCA_BE_PARAM_0 0xC350
+#define R_AX_MUEDCA_BE_PARAM_0_C1 0xE350
+#define B_AX_MUEDCA_BE_PARAM_0_TIMER_MASK GENMASK(31, 16)
+#define B_AX_MUEDCA_BE_PARAM_0_CW_MASK GENMASK(15, 8)
+#define B_AX_MUEDCA_BE_PARAM_0_AIFS_MASK GENMASK(7, 0)
+
+#define R_AX_MUEDCA_BK_PARAM_0 0xC354
+#define R_AX_MUEDCA_BK_PARAM_0_C1 0xE354
+#define R_AX_MUEDCA_VI_PARAM_0 0xC358
+#define R_AX_MUEDCA_VI_PARAM_0_C1 0xE358
+#define R_AX_MUEDCA_VO_PARAM_0 0xC35C
+#define R_AX_MUEDCA_VO_PARAM_0_C1 0xE35C
+
+#define R_AX_MUEDCA_EN 0xC370
+#define R_AX_MUEDCA_EN_C1 0xE370
+#define B_AX_MUEDCA_WMM_SEL BIT(8)
+#define B_AX_SET_MUEDCATIMER_TF_0 BIT(4)
+#define B_AX_MUEDCA_EN_0 BIT(0)
+
+#define R_AX_CCA_CONTROL 0xC390
+#define R_AX_CCA_CONTROL_C1 0xE390
+#define B_AX_TB_CHK_TX_NAV BIT(31)
+#define B_AX_TB_CHK_BASIC_NAV BIT(30)
+#define B_AX_TB_CHK_BTCCA BIT(29)
+#define B_AX_TB_CHK_EDCCA BIT(28)
+#define B_AX_TB_CHK_CCA_S80 BIT(27)
+#define B_AX_TB_CHK_CCA_S40 BIT(26)
+#define B_AX_TB_CHK_CCA_S20 BIT(25)
+#define B_AX_TB_CHK_CCA_P20 BIT(24)
+#define B_AX_SIFS_CHK_BTCCA BIT(21)
+#define B_AX_SIFS_CHK_EDCCA BIT(20)
+#define B_AX_SIFS_CHK_CCA_S80 BIT(19)
+#define B_AX_SIFS_CHK_CCA_S40 BIT(18)
+#define B_AX_SIFS_CHK_CCA_S20 BIT(17)
+#define B_AX_SIFS_CHK_CCA_P20 BIT(16)
+#define B_AX_CTN_CHK_TXNAV BIT(8)
+#define B_AX_CTN_CHK_INTRA_NAV BIT(7)
+#define B_AX_CTN_CHK_BASIC_NAV BIT(6)
+#define B_AX_CTN_CHK_BTCCA BIT(5)
+#define B_AX_CTN_CHK_EDCCA BIT(4)
+#define B_AX_CTN_CHK_CCA_S80 BIT(3)
+#define B_AX_CTN_CHK_CCA_S40 BIT(2)
+#define B_AX_CTN_CHK_CCA_S20 BIT(1)
+#define B_AX_CTN_CHK_CCA_P20 BIT(0)
+
+#define R_AX_SCHEDULE_ERR_IMR 0xC3E8
+#define R_AX_SCHEDULE_ERR_IMR_C1 0xE3E8
+#define B_AX_SORT_NON_IDLE_ERR_INT_EN BIT(1)
+#define B_AX_FSM_TIMEOUT_ERR_INT_EN BIT(0)
+
+#define R_AX_SCHEDULE_ERR_ISR 0xC3EC
+#define R_AX_SCHEDULE_ERR_ISR_C1 0xE3EC
+
+#define R_AX_SCH_DBG_SEL 0xC3F4
+#define R_AX_SCH_DBG_SEL_C1 0xE3F4
+#define B_AX_SCH_DBG_EN BIT(16)
+#define B_AX_SCH_CFG_CMD_SEL GENMASK(15, 8)
+#define B_AX_SCH_DBG_SEL_MASK GENMASK(7, 0)
+
+#define R_AX_SCH_DBG 0xC3F8
+#define R_AX_SCH_DBG_C1 0xE3F8
+#define B_AX_SCHEDULER_DBG_MASK GENMASK(31, 0)
+
+#define R_AX_PORT_CFG_P0 0xC400
+#define R_AX_PORT_CFG_P1 0xC440
+#define R_AX_PORT_CFG_P2 0xC480
+#define R_AX_PORT_CFG_P3 0xC4C0
+#define R_AX_PORT_CFG_P4 0xC500
+#define B_AX_BRK_SETUP BIT(16)
+#define B_AX_TBTT_UPD_SHIFT_SEL BIT(15)
+#define B_AX_BCN_DROP_ALLOW BIT(14)
+#define B_AX_TBTT_PROHIB_EN BIT(13)
+#define B_AX_BCNTX_EN BIT(12)
+#define B_AX_NET_TYPE_MASK GENMASK(11, 10)
+#define B_AX_BCN_FORCETX_EN BIT(9)
+#define B_AX_TXBCN_BTCCA_EN BIT(8)
+#define B_AX_BCNERR_CNT_EN BIT(7)
+#define B_AX_BCN_AGRES BIT(6)
+#define B_AX_TSFTR_RST BIT(5)
+#define B_AX_RX_BSSID_FIT_EN BIT(4)
+#define B_AX_TSF_UDT_EN BIT(3)
+#define B_AX_PORT_FUNC_EN BIT(2)
+#define B_AX_TXBCN_RPT_EN BIT(1)
+#define B_AX_RXBCN_RPT_EN BIT(0)
+
+#define R_AX_TBTT_PROHIB_P0 0xC404
+#define R_AX_TBTT_PROHIB_P1 0xC444
+#define R_AX_TBTT_PROHIB_P2 0xC484
+#define R_AX_TBTT_PROHIB_P3 0xC4C4
+#define R_AX_TBTT_PROHIB_P4 0xC504
+#define B_AX_TBTT_HOLD_MASK GENMASK(27, 16)
+#define B_AX_TBTT_SETUP_MASK GENMASK(7, 0)
+
+#define R_AX_BCN_AREA_P0 0xC408
+#define R_AX_BCN_AREA_P1 0xC448
+#define R_AX_BCN_AREA_P2 0xC488
+#define R_AX_BCN_AREA_P3 0xC4C8
+#define R_AX_BCN_AREA_P4 0xC508
+#define B_AX_BCN_MSK_AREA_MASK GENMASK(27, 16)
+#define B_AX_BCN_CTN_AREA_MASK GENMASK(11, 0)
+
+#define R_AX_BCNERLYINT_CFG_P0 0xC40C
+#define R_AX_BCNERLYINT_CFG_P1 0xC44C
+#define R_AX_BCNERLYINT_CFG_P2 0xC48C
+#define R_AX_BCNERLYINT_CFG_P3 0xC4CC
+#define R_AX_BCNERLYINT_CFG_P4 0xC50C
+#define B_AX_BCNERLY_MASK GENMASK(11, 0)
+
+#define R_AX_TBTTERLYINT_CFG_P0 0xC40E
+#define R_AX_TBTTERLYINT_CFG_P1 0xC44E
+#define R_AX_TBTTERLYINT_CFG_P2 0xC48E
+#define R_AX_TBTTERLYINT_CFG_P3 0xC4CE
+#define R_AX_TBTTERLYINT_CFG_P4 0xC50E
+#define B_AX_TBTTERLY_MASK GENMASK(11, 0)
+
+#define R_AX_TBTT_AGG_P0 0xC412
+#define R_AX_TBTT_AGG_P1 0xC452
+#define R_AX_TBTT_AGG_P2 0xC492
+#define R_AX_TBTT_AGG_P3 0xC4D2
+#define R_AX_TBTT_AGG_P4 0xC512
+#define B_AX_TBTT_AGG_NUM_MASK GENMASK(15, 8)
+
+#define R_AX_BCN_SPACE_CFG_P0 0xC414
+#define R_AX_BCN_SPACE_CFG_P1 0xC454
+#define R_AX_BCN_SPACE_CFG_P2 0xC494
+#define R_AX_BCN_SPACE_CFG_P3 0xC4D4
+#define R_AX_BCN_SPACE_CFG_P4 0xC514
+#define B_AX_SUB_BCN_SPACE_MASK GENMASK(23, 16)
+#define B_AX_BCN_SPACE_MASK GENMASK(15, 0)
+
+#define R_AX_BCN_FORCETX_P0 0xC418
+#define R_AX_BCN_FORCETX_P1 0xC458
+#define R_AX_BCN_FORCETX_P2 0xC498
+#define R_AX_BCN_FORCETX_P3 0xC4D8
+#define R_AX_BCN_FORCETX_P4 0xC518
+#define B_AX_FORCE_BCN_CURRCNT_MASK GENMASK(23, 16)
+#define B_AX_FORCE_BCN_NUM_MASK GENMASK(15, 0)
+#define B_AX_BCN_MAX_ERR_MASK GENMASK(7, 0)
+
+#define R_AX_BCN_ERR_CNT_P0 0xC420
+#define R_AX_BCN_ERR_CNT_P1 0xC460
+#define R_AX_BCN_ERR_CNT_P2 0xC4A0
+#define R_AX_BCN_ERR_CNT_P3 0xC4E0
+#define R_AX_BCN_ERR_CNT_P4 0xC520
+#define B_AX_BCN_ERR_CNT_SUM_MASK GENMASK(31, 24)
+#define B_AX_BCN_ERR_CNT_NAV_MASK GENMASK(23, 16)
+#define B_AX_BCN_ERR_CNT_EDCCA_MASK GENMASK(15, 0)
+#define B_AX_BCN_ERR_CNT_CCA_MASK GENMASK(7, 0)
+
+#define R_AX_BCN_ERR_FLAG_P0 0xC424
+#define R_AX_BCN_ERR_FLAG_P1 0xC464
+#define R_AX_BCN_ERR_FLAG_P2 0xC4A4
+#define R_AX_BCN_ERR_FLAG_P3 0xC4E4
+#define R_AX_BCN_ERR_FLAG_P4 0xC524
+#define B_AX_BCN_ERR_FLAG_OTHERS BIT(6)
+#define B_AX_BCN_ERR_FLAG_MAC BIT(5)
+#define B_AX_BCN_ERR_FLAG_TXON BIT(4)
+#define B_AX_BCN_ERR_FLAG_SRCHEND BIT(3)
+#define B_AX_BCN_ERR_FLAG_INVALID BIT(2)
+#define B_AX_BCN_ERR_FLAG_CMP BIT(1)
+#define B_AX_BCN_ERR_FLAG_LOCK BIT(0)
+
+#define R_AX_DTIM_CTRL_P0 0xC426
+#define R_AX_DTIM_CTRL_P1 0xC466
+#define R_AX_DTIM_CTRL_P2 0xC4A6
+#define R_AX_DTIM_CTRL_P3 0xC4E6
+#define R_AX_DTIM_CTRL_P4 0xC526
+#define B_AX_DTIM_NUM_MASK GENMASK(15, 0)
+#define B_AX_DTIM_CURRCNT_MASK GENMASK(7, 0)
+
+#define R_AX_TBTT_SHIFT_P0 0xC428
+#define R_AX_TBTT_SHIFT_P1 0xC468
+#define R_AX_TBTT_SHIFT_P2 0xC4A8
+#define R_AX_TBTT_SHIFT_P3 0xC4E8
+#define R_AX_TBTT_SHIFT_P4 0xC528
+#define B_AX_TBTT_SHIFT_OFST_MASK GENMASK(11, 0)
+
+#define R_AX_BCN_CNT_TMR_P0 0xC434
+#define R_AX_BCN_CNT_TMR_P1 0xC474
+#define R_AX_BCN_CNT_TMR_P2 0xC4B4
+#define R_AX_BCN_CNT_TMR_P3 0xC4F4
+#define R_AX_BCN_CNT_TMR_P4 0xC534
+#define B_AX_BCN_CNT_TMR_MASK GENMASK(31, 0)
+
+#define R_AX_TSFTR_LOW_P0 0xC438
+#define R_AX_TSFTR_LOW_P1 0xC478
+#define R_AX_TSFTR_LOW_P2 0xC4B8
+#define R_AX_TSFTR_LOW_P3 0xC4F8
+#define R_AX_TSFTR_LOW_P4 0xC538
+#define B_AX_TSFTR_LOW_MASK GENMASK(31, 0)
+
+#define R_AX_TSFTR_HIGH_P0 0xC43C
+#define R_AX_TSFTR_HIGH_P1 0xC47C
+#define R_AX_TSFTR_HIGH_P2 0xC4BC
+#define R_AX_TSFTR_HIGH_P3 0xC4FC
+#define R_AX_TSFTR_HIGH_P4 0xC53C
+#define B_AX_TSFTR_HIGH_MASK GENMASK(31, 0)
+
+#define R_AX_MBSSID_CTRL 0xC568
+#define R_AX_MBSSID_CTRL_C1 0xE568
+#define B_AX_P0MB_ALL_MASK GENMASK(23, 1)
+#define B_AX_P0MB_NUM_MASK GENMASK(19, 16)
+#define B_AX_P0MB15_EN BIT(15)
+#define B_AX_P0MB14_EN BIT(14)
+#define B_AX_P0MB13_EN BIT(13)
+#define B_AX_P0MB12_EN BIT(12)
+#define B_AX_P0MB11_EN BIT(11)
+#define B_AX_P0MB10_EN BIT(10)
+#define B_AX_P0MB9_EN BIT(9)
+#define B_AX_P0MB8_EN BIT(8)
+#define B_AX_P0MB7_EN BIT(7)
+#define B_AX_P0MB6_EN BIT(6)
+#define B_AX_P0MB5_EN BIT(5)
+#define B_AX_P0MB4_EN BIT(4)
+#define B_AX_P0MB3_EN BIT(3)
+#define B_AX_P0MB2_EN BIT(2)
+#define B_AX_P0MB1_EN BIT(1)
+
+#define R_AX_AMPDU_AGG_LIMIT 0xC610
+#define B_AX_AMPDU_MAX_TIME_MASK GENMASK(31, 24)
+#define B_AX_RA_TRY_RATE_AGG_LMT_MASK GENMASK(23, 16)
+#define B_AX_RTS_MAX_AGG_NUM_MASK GENMASK(15, 8)
+#define B_AX_MAX_AGG_NUM_MASK GENMASK(7, 0)
+
+#define R_AX_AGG_LEN_HT_0 0xC614
+#define R_AX_AGG_LEN_HT_0_C1 0xE614
+#define B_AX_AMPDU_MAX_LEN_HT_MASK GENMASK(31, 16)
+#define B_AX_RTS_TXTIME_TH_MASK GENMASK(15, 8)
+#define B_AX_RTS_LEN_TH_MASK GENMASK(7, 0)
+
+#define S_AX_CTS2S_TH_SEC_256B 1
+#define R_AX_SIFS_SETTING 0xC624
+#define R_AX_SIFS_SETTING_C1 0xE624
+#define B_AX_HW_CTS2SELF_PKT_LEN_TH_MASK GENMASK(31, 24)
+#define B_AX_HW_CTS2SELF_PKT_LEN_TH_TWW_MASK GENMASK(23, 18)
+#define B_AX_HW_CTS2SELF_EN BIT(16)
+#define B_AX_SPEC_SIFS_OFDM_PTCL_SH 8
+#define B_AX_SPEC_SIFS_OFDM_PTCL_MASK GENMASK(15, 8)
+#define B_AX_SPEC_SIFS_CCK_PTCL_MASK GENMASK(7, 0)
+#define S_AX_CTS2S_TH_1K 4
+
+#define R_AX_TXRATE_CHK 0xC628
+#define R_AX_TXRATE_CHK_C1 0xE628
+#define B_AX_DEFT_RATE_MASK GENMASK(15, 7)
+#define B_AX_BAND_MODE BIT(4)
+#define B_AX_MAX_TXNSS_MASK GENMASK(3, 2)
+#define B_AX_RTS_LIMIT_IN_OFDM6 BIT(1)
+#define B_AX_CHECK_CCK_EN BIT(0)
+
+#define R_AX_TXCNT 0xC62C
+#define R_AX_TXCNT_C1 0xE62C
+#define B_AX_ADD_TXCNT_BY BIT(31)
+#define B_AX_S_TXCNT_LMT_MASK GENMASK(29, 24)
+#define B_AX_L_TXCNT_LMT_MASK GENMASK(21, 16)
+
+#define R_AX_MBSSID_DROP_0 0xC63C
+#define R_AX_MBSSID_DROP_0_C1 0xE63C
+#define B_AX_GI_LTF_FB_SEL BIT(30)
+#define B_AX_RATE_SEL_MASK GENMASK(29, 24)
+#define B_AX_PORT_DROP_4_0_MASK GENMASK(20, 16)
+#define B_AX_MBSSID_DROP_15_0_MASK GENMASK(15, 0)
+
+#define R_AX_BT_PLT 0xC67C
+#define R_AX_BT_PLT_C1 0xE67C
+#define B_AX_BT_PLT_PKT_CNT_MASK GENMASK(31, 16)
+#define B_AX_BT_PLT_RST BIT(9)
+#define B_AX_PLT_EN BIT(8)
+#define B_AX_RX_PLT_GNT_LTE_RX BIT(7)
+#define B_AX_RX_PLT_GNT_BT_RX BIT(6)
+#define B_AX_RX_PLT_GNT_BT_TX BIT(5)
+#define B_AX_RX_PLT_GNT_WL BIT(4)
+#define B_AX_TX_PLT_GNT_LTE_RX BIT(3)
+#define B_AX_TX_PLT_GNT_BT_RX BIT(2)
+#define B_AX_TX_PLT_GNT_BT_TX BIT(1)
+#define B_AX_TX_PLT_GNT_WL BIT(0)
+
+#define R_AX_PTCL_BSS_COLOR_0 0xC6A0
+#define R_AX_PTCL_BSS_COLOR_0_C1 0xE6A0
+#define B_AX_BSS_COLOB_AX_PORT_3_MASK GENMASK(29, 24)
+#define B_AX_BSS_COLOB_AX_PORT_2_MASK GENMASK(21, 16)
+#define B_AX_BSS_COLOB_AX_PORT_1_MASK GENMASK(13, 8)
+#define B_AX_BSS_COLOB_AX_PORT_0_MASK GENMASK(5, 0)
+
+#define R_AX_PTCL_BSS_COLOR_1 0xC6A4
+#define R_AX_PTCL_BSS_COLOR_1_C1 0xE6A4
+#define B_AX_BSS_COLOB_AX_PORT_4_MASK GENMASK(5, 0)
+
+#define R_AX_PTCL_IMR0 0xC6C0
+#define R_AX_PTCL_IMR0_C1 0xE6C0
+#define B_AX_F2PCMD_USER_ALLC_ERR_INT_EN BIT(28)
+#define B_AX_TX_RECORD_PKTID_ERR_INT_EN BIT(23)
+
+#define R_AX_PTCL_ISR0 0xC6C4
+#define R_AX_PTCL_ISR0_C1 0xE6C4
+
+#define S_AX_PTCL_TO_2MS 0x3F
+#define R_AX_PTCL_FSM_MON 0xC6E8
+#define R_AX_PTCL_FSM_MON_C1 0xE6E8
+#define B_AX_PTCL_TX_ARB_TO_MODE BIT(6)
+#define B_AX_PTCL_TX_ARB_TO_THR_MASK GENMASK(5, 0)
+
+#define R_AX_PTCL_TX_CTN_SEL 0xC6EC
+#define R_AX_PTCL_TX_CTN_SEL_C1 0xE6EC
+#define B_AX_PTCL_TX_ON_STAT BIT(7)
+
+#define R_AX_PTCL_DBG_INFO 0xC6F0
+#define R_AX_PTCL_DBG_INFO_C1 0xE6F0
+#define B_AX_PTCL_DBG_INFO_MASK GENMASK(31, 0)
+#define R_AX_PTCL_DBG 0xC6F4
+#define R_AX_PTCL_DBG_C1 0xE6F4
+#define B_AX_PTCL_DBG_EN BIT(8)
+#define B_AX_PTCL_DBG_SEL_MASK GENMASK(7, 0)
+
+#define R_AX_DLE_CTRL 0xC800
+#define R_AX_DLE_CTRL_C1 0xE800
+#define B_AX_NO_RESERVE_PAGE_ERR_IMR BIT(23)
+#define B_AX_RXDATA_FSM_HANG_ERROR_IMR BIT(15)
+#define R_AX_RXDMA_PKT_INFO_0 0xC814
+#define R_AX_RXDMA_PKT_INFO_1 0xC818
+#define R_AX_RXDMA_PKT_INFO_2 0xC81C
+
+#define R_AX_TCR1 0xCA04
+#define R_AX_TCR1_C1 0xEA04
+#define B_AX_TXDFIFO_THRESHOLD GENMASK(31, 28)
+#define B_AX_TCR_CCK_LOCK_CLK BIT(27)
+#define B_AX_TCR_FORCE_READ_TXDFIFO BIT(26)
+#define B_AX_TCR_USTIME GENMASK(23, 16)
+#define B_AX_TCR_SMOOTH_VAL BIT(15)
+#define B_AX_TCR_SMOOTH_CTRL BIT(14)
+#define B_AX_CS_REQ_VAL BIT(13)
+#define B_AX_CS_REQ_SEL BIT(12)
+#define B_AX_TCR_ZLD_USTIME_AFTERPHYTXON GENMASK(11, 8)
+#define B_AX_TCR_TXTIMEOUT GENMASK(7, 0)
+
+#define R_AX_PPWRBIT_SETTING 0xCA0C
+#define R_AX_PPWRBIT_SETTING_C1 0xEA0C
+
+#define R_AX_MACTX_DBG_SEL_CNT 0xCA20
+#define R_AX_MACTX_DBG_SEL_CNT_C1 0xEA20
+#define B_AX_MACTX_MPDU_CNT GENMASK(31, 24)
+#define B_AX_MACTX_DMA_CNT GENMASK(23, 16)
+#define B_AX_LENGTH_ERR_FLAG_U3 BIT(11)
+#define B_AX_LENGTH_ERR_FLAG_U2 BIT(10)
+#define B_AX_LENGTH_ERR_FLAG_U1 BIT(9)
+#define B_AX_LENGTH_ERR_FLAG_U0 BIT(8)
+#define B_AX_DBGSEL_MACTX_MASK GENMASK(5, 0)
+
+#define R_AX_WMAC_TX_CTRL_DEBUG 0xCAE4
+#define R_AX_WMAC_TX_CTRL_DEBUG_C1 0xEAE4
+#define B_AX_TX_CTRL_DEBUG_SEL_MASK GENMASK(3, 0)
+
+#define R_AX_WMAC_TX_INFO0_DEBUG 0xCAE8
+#define R_AX_WMAC_TX_INFO0_DEBUG_C1 0xEAE8
+#define B_AX_TX_CTRL_INFO_P0_MASK GENMASK(31, 0)
+
+#define R_AX_WMAC_TX_INFO1_DEBUG 0xCAEC
+#define R_AX_WMAC_TX_INFO1_DEBUG_C1 0xEAEC
+#define B_AX_TX_CTRL_INFO_P1_MASK GENMASK(31, 0)
+
+#define R_AX_RSP_CHK_SIG 0xCC00
+#define R_AX_RSP_CHK_SIG_C1 0xEC00
+#define B_AX_RSP_STATIC_RTS_CHK_SERV_BW_EN BIT(30)
+#define B_AX_RSP_TBPPDU_CHK_PWR BIT(29)
+#define B_AX_RSP_CHK_BASIC_NAV BIT(21)
+#define B_AX_RSP_CHK_INTRA_NAV BIT(20)
+#define B_AX_RSP_CHK_TXNAV BIT(19)
+#define B_AX_TXDATA_END_PS_OPT BIT(18)
+#define B_AX_CHECK_SOUNDING_SEQ BIT(17)
+#define B_AX_RXBA_IGNOREA2 BIT(16)
+#define B_AX_ACKTO_CCK_MASK GENMASK(15, 8)
+#define B_AX_ACKTO_MASK GENMASK(7, 0)
+
+#define R_AX_TRXPTCL_RESP_0 0xCC04
+#define R_AX_TRXPTCL_RESP_0_C1 0xEC04
+#define B_AX_WMAC_RESP_STBC_EN BIT(31)
+#define B_AX_WMAC_RXFTM_TXACK_SC BIT(30)
+#define B_AX_WMAC_RXFTM_TXACKBWEQ BIT(29)
+#define B_AX_RSP_CHK_SEC_CCA_80 BIT(28)
+#define B_AX_RSP_CHK_SEC_CCA_40 BIT(27)
+#define B_AX_RSP_CHK_SEC_CCA_20 BIT(26)
+#define B_AX_RSP_CHK_BTCCA BIT(25)
+#define B_AX_RSP_CHK_EDCCA BIT(24)
+#define B_AX_RSP_CHK_CCA BIT(23)
+#define B_AX_WMAC_LDPC_EN BIT(22)
+#define B_AX_WMAC_SGIEN BIT(21)
+#define B_AX_WMAC_SPLCPEN BIT(20)
+#define B_AX_WMAC_BESP_EARLY_TXBA BIT(17)
+#define B_AX_WMAC_SPEC_SIFS_OFDM_MASK GENMASK(15, 8)
+#define B_AX_WMAC_SPEC_SIFS_CCK_MASK GENMASK(7, 0)
+#define WMAC_SPEC_SIFS_OFDM_52A 0x15
+#define WMAC_SPEC_SIFS_OFDM_52B 0x11
+#define WMAC_SPEC_SIFS_OFDM_52C 0x11
+#define WMAC_SPEC_SIFS_CCK	 0xA
+
+#define R_AX_MAC_LOOPBACK 0xCC20
+#define R_AX_MAC_LOOPBACK_C1 0xEC20
+#define B_AX_MACLBK_EN BIT(0)
+
+#define R_AX_RXTRIG_TEST_USER_2 0xCCB0
+#define R_AX_RXTRIG_TEST_USER_2_C1 0xECB0
+#define B_AX_RXTRIG_MACID_MASK GENMASK(31, 24)
+#define B_AX_RXTRIG_RU26_DIS BIT(21)
+#define B_AX_RXTRIG_FCSCHK_EN BIT(20)
+#define B_AX_RXTRIG_PORT_SEL_MASK GENMASK(19, 17)
+#define B_AX_RXTRIG_EN BIT(16)
+#define B_AX_RXTRIG_USERINFO_2_MASK GENMASK(15, 0)
+
+#define R_AX_WMAC_TX_TF_INFO_0 0xCCD0
+#define R_AX_WMAC_TX_TF_INFO_0_C1 0xECD0
+#define B_AX_WMAC_TX_TF_INFO_SEL_MASK GENMASK(2, 0)
+
+#define R_AX_WMAC_TX_TF_INFO_1 0xCCD4
+#define R_AX_WMAC_TX_TF_INFO_1_C1 0xECD4
+#define B_AX_WMAC_TX_TF_INFO_P0_MASK GENMASK(31, 0)
+
+#define R_AX_WMAC_TX_TF_INFO_2 0xCCD8
+#define R_AX_WMAC_TX_TF_INFO_2_C1 0xECD8
+#define B_AX_WMAC_TX_TF_INFO_P1_MASK GENMASK(31, 0)
+
+#define R_AX_TMAC_ERR_IMR_ISR 0xCCEC
+#define R_AX_TMAC_ERR_IMR_ISR_C1 0xECEC
+
+#define R_AX_DBGSEL_TRXPTCL 0xCCF4
+#define R_AX_DBGSEL_TRXPTCL_C1 0xECF4
+#define B_AX_DBGSEL_TRXPTCL_MASK GENMASK(7, 0)
+
+#define R_AX_PHYINFO_ERR_IMR 0xCCFC
+#define R_AX_PHYINFO_ERR_IMR_C1 0xECFC
+#define B_AX_CSI_ON_TIMEOUT BIT(29)
+#define B_AX_STS_ON_TIMEOUT BIT(28)
+#define B_AX_DATA_ON_TIMEOUT BIT(27)
+#define B_AX_OFDM_CCA_TIMEOUT BIT(26)
+#define B_AX_CCK_CCA_TIMEOUT BIT(25)
+#define B_AXC_PHY_TXON_TIMEOUT BIT(24)
+#define B_AX_CSI_ON_TIMEOUT_INT_EN BIT(21)
+#define B_AX_STS_ON_TIMEOUT_INT_EN BIT(20)
+#define B_AX_DATA_ON_TIMEOUT_INT_EN BIT(19)
+#define B_AX_OFDM_CCA_TIMEOUT_INT_EN BIT(18)
+#define B_AX_CCK_CCA_TIMEOUT_INT_EN BIT(17)
+#define B_AX_PHY_TXON_TIMEOUT_INT_EN BIT(16)
+#define B_AX_PHYINTF_TIMEOUT_THR_MSAK GENMASK(5, 0)
+
+#define R_AX_PHYINFO_ERR_ISR 0xCCFC
+#define R_AX_PHYINFO_ERR_ISR_C1 0xECFC
+
+#define R_AX_BFMER_CTRL_0 0xCD78
+#define R_AX_BFMER_CTRL_0_C1 0xED78
+#define B_AX_BFMER_HE_CSI_OFFSET_MASK GENMASK(31, 24)
+#define B_AX_BFMER_VHT_CSI_OFFSET_MASK GENMASK(23, 16)
+#define B_AX_BFMER_HT_CSI_OFFSET_MASK GENMASK(15, 8)
+#define B_AX_BFMER_NDP_BFEN BIT(2)
+#define B_AX_BFMER_VHT_BFPRT_CHK BIT(0)
+
+#define R_AX_BFMEE_RESP_OPTION 0xCD80
+#define R_AX_BFMEE_RESP_OPTION_C1 0xED80
+#define B_AX_BFMEE_NDP_RX_STANDBY_TIMER_MASK GENMASK(31, 24)
+#define B_AX_BFMEE_BFRP_RX_STANDBY_TIMER_MASK GENMASK(23, 20)
+#define B_AX_MU_BFRPTSEG_SEL_MASK GENMASK(18, 17)
+#define B_AX_BFMEE_NDP_RXSTDBY_SEL BIT(16)
+#define BFRP_RX_STANDBY_TIMER		0x0
+#define NDP_RX_STANDBY_TIMER		0xFF
+#define B_AX_BFMEE_HE_NDPA_EN BIT(2)
+#define B_AX_BFMEE_VHT_NDPA_EN BIT(1)
+#define B_AX_BFMEE_HT_NDPA_EN BIT(0)
+
+#define R_AX_TRXPTCL_RESP_CSI_CTRL_0 0xCD88
+#define R_AX_TRXPTCL_RESP_CSI_CTRL_0_C1 0xED88
+#define R_AX_TRXPTCL_RESP_CSI_CTRL_1 0xCD94
+#define R_AX_TRXPTCL_RESP_CSI_CTRL_1_C1 0xED94
+#define B_AX_BFMEE_CSISEQ_SEL BIT(29)
+#define B_AX_BFMEE_BFPARAM_SEL BIT(28)
+#define B_AX_BFMEE_OFDM_LEN_TH_MASK GENMASK(27, 24)
+#define B_AX_BFMEE_BF_PORT_SEL BIT(23)
+#define B_AX_BFMEE_USE_NSTS BIT(22)
+#define B_AX_BFMEE_CSI_RATE_FB_EN BIT(21)
+#define B_AX_BFMEE_CSI_GID_SEL BIT(20)
+#define B_AX_BFMEE_CSI_RSC_MASK GENMASK(19, 18)
+#define B_AX_BFMEE_CSI_FORCE_RETE_EN BIT(17)
+#define B_AX_BFMEE_CSI_USE_NDPARATE BIT(16)
+#define B_AX_BFMEE_CSI_WITHHTC_EN BIT(15)
+#define B_AX_BFMEE_CSIINFO0_BF_EN BIT(14)
+#define B_AX_BFMEE_CSIINFO0_STBC_EN BIT(13)
+#define B_AX_BFMEE_CSIINFO0_LDPC_EN BIT(12)
+#define B_AX_BFMEE_CSIINFO0_CS_MASK GENMASK(11, 10)
+#define B_AX_BFMEE_CSIINFO0_CB_MASK GENMASK(9, 8)
+#define B_AX_BFMEE_CSIINFO0_NG_MASK GENMASK(7, 6)
+#define B_AX_BFMEE_CSIINFO0_NR_MASK GENMASK(5, 3)
+#define B_AX_BFMEE_CSIINFO0_NC_MASK GENMASK(2, 0)
+
+#define R_AX_TRXPTCL_RESP_CSI_RRSC 0xCD8C
+#define R_AX_TRXPTCL_RESP_CSI_RRSC_C1 0xED8C
+#define CSI_RRSC_BMAP 0x29292911
+
+#define R_AX_TRXPTCL_RESP_CSI_RATE 0xCD90
+#define R_AX_TRXPTCL_RESP_CSI_RATE_C1 0xED90
+#define B_AX_BFMEE_HE_CSI_RATE_MASK GENMASK(22, 16)
+#define B_AX_BFMEE_VHT_CSI_RATE_MASK GENMASK(14, 8)
+#define B_AX_BFMEE_HT_CSI_RATE_MASK GENMASK(6, 0)
+#define CSI_INIT_RATE_HE		0x3
+#define CSI_INIT_RATE_VHT		0x3
+#define CSI_INIT_RATE_HT		0x3
+
+#define R_AX_RCR 0xCE00
+#define R_AX_RCR_C1 0xEE00
+#define B_AX_STOP_RX_IN BIT(11)
+#define B_AX_DRV_INFO_SIZE_MASK GENMASK(10, 8)
+#define B_AX_CH_EN_MASK GENMASK(3, 0)
+
+#define R_AX_DLK_PROTECT_CTL 0xCE02
+#define R_AX_DLK_PROTECT_CTL_C1 0xEE02
+#define B_AX_RX_DLK_CCA_TIME_MASK GENMASK(15, 8)
+#define B_AX_RX_DLK_DATA_TIME_MASK GENMASK(7, 4)
+
+#define R_AX_PLCP_HDR_FLTR 0xCE04
+#define R_AX_PLCP_HDR_FLTR_C1 0xEE04
+#define B_AX_DIS_CHK_MIN_LEN BIT(8)
+#define B_AX_HE_SIGB_CRC_CHK BIT(6)
+#define B_AX_VHT_MU_SIGB_CRC_CHK BIT(5)
+#define B_AX_VHT_SU_SIGB_CRC_CHK BIT(4)
+#define B_AX_SIGA_CRC_CHK BIT(3)
+#define B_AX_LSIG_PARITY_CHK_EN BIT(2)
+#define B_AX_CCK_SIG_CHK BIT(1)
+#define B_AX_CCK_CRC_CHK BIT(0)
+
+#define R_AX_RX_FLTR_OPT 0xCE20
+#define R_AX_RX_FLTR_OPT_C1 0xEE20
+#define B_AX_UID_FILTER_MASK GENMASK(31, 24)
+#define B_AX_UNSPT_FILTER_SH 22
+#define B_AX_UNSPT_FILTER_MASK GENMASK(23, 22)
+#define B_AX_RX_MPDU_MAX_LEN_MASK GENMASK(21, 16)
+#define B_AX_RX_MPDU_MAX_LEN_SIZE 0x3f
+#define B_AX_A_FTM_REQ BIT(14)
+#define B_AX_A_ERR_PKT BIT(13)
+#define B_AX_A_UNSUP_PKT BIT(12)
+#define B_AX_A_CRC32_ERR BIT(11)
+#define B_AX_A_PWR_MGNT BIT(10)
+#define B_AX_A_BCN_CHK_RULE_MASK GENMASK(9, 8)
+#define B_AX_A_BCN_CHK_EN BIT(7)
+#define B_AX_A_MC_LIST_CAM_MATCH BIT(6)
+#define B_AX_A_BC_CAM_MATCH BIT(5)
+#define B_AX_A_UC_CAM_MATCH BIT(4)
+#define B_AX_A_MC BIT(3)
+#define B_AX_A_BC BIT(2)
+#define B_AX_A_A1_MATCH BIT(1)
+#define B_AX_SNIFFER_MODE BIT(0)
+#define DEFAULT_AX_RX_FLTR (B_AX_A_A1_MATCH | B_AX_A_BC | B_AX_A_MC |	       \
+			    B_AX_A_UC_CAM_MATCH | B_AX_A_BC_CAM_MATCH |	       \
+			    B_AX_A_PWR_MGNT | B_AX_A_FTM_REQ |		       \
+			    u32_encode_bits(3, B_AX_UID_FILTER_MASK) |	       \
+			    B_AX_A_BCN_CHK_EN)
+#define B_AX_RX_FLTR_CFG_MASK ((u32)~B_AX_RX_MPDU_MAX_LEN_MASK)
+
+#define R_AX_CTRL_FLTR 0xCE24
+#define R_AX_CTRL_FLTR_C1 0xEE24
+#define R_AX_MGNT_FLTR 0xCE28
+#define R_AX_MGNT_FLTR_C1 0xEE28
+#define R_AX_DATA_FLTR 0xCE2C
+#define R_AX_DATA_FLTR_C1 0xEE2C
+#define RX_FLTR_FRAME_DROP	0x00000000
+#define RX_FLTR_FRAME_TO_HOST	0x55555555
+#define RX_FLTR_FRAME_TO_WLCPU	0xAAAAAAAA
+
+#define R_AX_ADDR_CAM_CTRL 0xCE34
+#define R_AX_ADDR_CAM_CTRL_C1 0xEE34
+#define B_AX_ADDR_CAM_RANGE_MASK GENMASK(23, 16)
+#define B_AX_ADDR_CAM_CMPLIMT_MASK GENMASK(15, 12)
+#define B_AX_ADDR_CAM_CLR BIT(8)
+#define B_AX_ADDR_CAM_A2_B0_CHK BIT(2)
+#define B_AX_ADDR_CAM_SRCH_PERPKT BIT(1)
+#define B_AX_ADDR_CAM_EN BIT(0)
+
+#define R_AX_RESPBA_CAM_CTRL 0xCE3C
+#define R_AX_RESPBA_CAM_CTRL_C1 0xEE3C
+#define B_AX_SSN_SEL BIT(2)
+
+#define R_AX_PPDU_STAT 0xCE40
+#define R_AX_PPDU_STAT_C1 0xEE40
+#define B_AX_PPDU_STAT_RPT_TRIG BIT(8)
+#define B_AX_PPDU_STAT_RPT_CRC32 BIT(5)
+#define B_AX_PPDU_STAT_RPT_A1M BIT(4)
+#define B_AX_APP_PLCP_HDR_RPT BIT(3)
+#define B_AX_APP_RX_CNT_RPT BIT(2)
+#define B_AX_APP_MAC_INFO_RPT BIT(1)
+#define B_AX_PPDU_STAT_RPT_EN BIT(0)
+
+#define R_AX_RX_SR_CTRL 0xCE4A
+#define R_AX_RX_SR_CTRL_C1 0xEE4A
+#define B_AX_SR_EN BIT(0)
+
+#define R_AX_RX_STATE_MONITOR 0xCEF0
+#define R_AX_RX_STATE_MONITOR_C1 0xEEF0
+#define B_AX_RX_STATE_MONITOR_MASK GENMASK(31, 0)
+#define B_AX_STATE_CUR_MASK GENMASK(31, 16)
+#define B_AX_STATE_NXT_MASK GENMASK(13, 8)
+#define B_AX_STATE_UPD BIT(7)
+#define B_AX_STATE_SEL_MASK GENMASK(4, 0)
+
+#define R_AX_RMAC_ERR_ISR 0xCEF4
+#define R_AX_RMAC_ERR_ISR_C1 0xEEF4
+#define B_AX_RXERR_INTPS_EN BIT(31)
+#define B_AX_RMAC_RX_CSI_TIMEOUT_INT_EN BIT(19)
+#define B_AX_RMAC_RX_TIMEOUT_INT_EN BIT(18)
+#define B_AX_RMAC_CSI_TIMEOUT_INT_EN BIT(17)
+#define B_AX_RMAC_DATA_ON_TIMEOUT_INT_EN BIT(16)
+#define B_AX_RMAC_CCA_TIMEOUT_INT_EN BIT(15)
+#define B_AX_RMAC_DMA_TIMEOUT_INT_EN BIT(14)
+#define B_AX_RMAC_DATA_ON_TO_IDLE_TIMEOUT_INT_EN BIT(13)
+#define B_AX_RMAC_CCA_TO_IDLE_TIMEOUT_INT_EN BIT(12)
+#define B_AX_RMAC_RX_CSI_TIMEOUT_FLAG BIT(7)
+#define B_AX_RMAC_RX_TIMEOUT_FLAG BIT(6)
+#define B_AX_BMAC_CSI_TIMEOUT_FLAG BIT(5)
+#define B_AX_BMAC_DATA_ON_TIMEOUT_FLAG BIT(4)
+#define B_AX_BMAC_CCA_TIMEOUT_FLAG BIT(3)
+#define B_AX_BMAC_DMA_TIMEOUT_FLAG BIT(2)
+#define B_AX_BMAC_DATA_ON_TO_IDLE_TIMEOUT_FLAG BIT(1)
+#define B_AX_BMAC_CCA_TO_IDLE_TIMEOUT_FLAG BIT(0)
+
+#define R_AX_RMAC_PLCP_MON 0xCEF8
+#define R_AX_RMAC_PLCP_MON_C1 0xEEF8
+#define B_AX_RMAC_PLCP_MON_MASK GENMASK(31, 0)
+#define B_AX_PCLP_MON_SEL_MASK GENMASK(31, 28)
+#define B_AX_PCLP_MON_CONT_MASK GENMASK(27, 0)
+
+#define R_AX_RX_DEBUG_SELECT 0xCEFC
+#define R_AX_RX_DEBUG_SELECT_C1 0xEEFC
+#define B_AX_DEBUG_SEL_MASK GENMASK(7, 0)
+
+#define R_AX_PWR_RATE_CTRL 0xD200
+#define R_AX_PWR_RATE_CTRL_C1 0xF200
+#define B_AX_FORCE_PWR_BY_RATE_EN BIT(9)
+#define B_AX_FORCE_PWR_BY_RATE_VALUE_MASK GENMASK(8, 0)
+
+#define R_AX_PWR_RATE_OFST_CTRL 0xD204
+#define R_AX_PWR_COEXT_CTRL 0xD220
+#define B_AX_TXAGC_BT_EN BIT(1)
+#define B_AX_TXAGC_BT_MASK GENMASK(11, 3)
+
+#define R_AX_PWR_UL_CTRL0 0xD240
+#define R_AX_PWR_UL_CTRL2 0xD248
+#define B_AX_PWR_UL_CFO_MASK GENMASK(2, 0)
+#define B_AX_PWR_UL_CTRL2_MASK 0x07700007
+#define R_AX_PWR_UL_TB_CTRL 0xD288
+#define B_AX_PWR_UL_TB_CTRL_EN BIT(31)
+#define R_AX_PWR_UL_TB_1T 0xD28C
+#define B_AX_PWR_UL_TB_1T_MASK GENMASK(4, 0)
+#define R_AX_PWR_UL_TB_2T 0xD290
+#define B_AX_PWR_UL_TB_2T_MASK GENMASK(4, 0)
+#define R_AX_PWR_BY_RATE_TABLE0 0xD2C0
+#define R_AX_PWR_BY_RATE_TABLE10 0xD2E8
+#define R_AX_PWR_BY_RATE R_AX_PWR_BY_RATE_TABLE0
+#define R_AX_PWR_BY_RATE_MAX R_AX_PWR_BY_RATE_TABLE10
+#define R_AX_PWR_LMT_TABLE0 0xD2EC
+#define R_AX_PWR_LMT_TABLE19 0xD338
+#define R_AX_PWR_LMT R_AX_PWR_LMT_TABLE0
+#define R_AX_PWR_LMT_MAX R_AX_PWR_LMT_TABLE19
+#define R_AX_PWR_RU_LMT_TABLE0 0xD33C
+#define R_AX_PWR_RU_LMT_TABLE11 0xD368
+#define R_AX_PWR_RU_LMT R_AX_PWR_RU_LMT_TABLE0
+#define R_AX_PWR_RU_LMT_MAX R_AX_PWR_RU_LMT_TABLE11
+#define R_AX_PWR_MACID_LMT_TABLE0 0xD36C
+#define R_AX_PWR_MACID_LMT_TABLE127 0xD568
+
+#define R_AX_TXPWR_IMR 0xD9E0
+#define R_AX_TXPWR_IMR_C1 0xF9E0
+#define R_AX_TXPWR_ISR 0xD9E4
+#define R_AX_TXPWR_ISR_C1 0xF9E4
+
+#define R_AX_BTC_CFG 0xDA00
+#define B_AX_DIS_BTC_CLK_G BIT(2)
+
+#define R_AX_WL_PRI_MSK 0xDA10
+#define B_AX_PTA_WL_PRI_MASK_BCNQ BIT(8)
+
+#define R_AX_BTC_FUNC_EN 0xDA20
+#define R_AX_BTC_FUNC_EN_C1 0xFA20
+#define B_AX_PTA_WL_TX_EN BIT(1)
+#define B_AX_PTA_EDCCA_EN BIT(0)
+
+#define R_BTC_BREAK_TABLE 0xDA2C
+#define BTC_BREAK_PARAM 0xf0ffffff
+
+#define R_BTC_BT_COEX_MSK_TABLE 0xDA30
+#define B_BTC_PRI_MASK_TX_RESP_V1 BIT(3)
+
+#define R_AX_BT_COEX_CFG_2 0xDA34
+#define R_AX_BT_COEX_CFG_2_C1 0xFA34
+#define B_AX_GNT_BT_BYPASS_PRIORITY BIT(12)
+#define B_AX_GNT_BT_POLARITY BIT(8)
+#define B_AX_TIMER_MASK GENMASK(7, 0)
+#define MAC_AX_CSR_RATE 80
+
+#define R_AX_CSR_MODE 0xDA40
+#define R_AX_CSR_MODE_C1 0xFA40
+#define B_AX_BT_CNT_RST BIT(16)
+#define B_AX_BT_STAT_DELAY_MASK GENMASK(15, 12)
+#define MAC_AX_CSR_DELAY 0
+#define B_AX_BT_TRX_INIT_DETECT_MASK GENMASK(11, 8)
+#define MAC_AX_CSR_TRX_TO 4
+#define B_AX_BT_PRI_DETECT_TO_MASK GENMASK(7, 4)
+#define MAC_AX_CSR_PRI_TO 5
+#define B_AX_WL_ACT_MSK BIT(3)
+#define B_AX_STATIS_BT_EN BIT(2)
+#define B_AX_WL_ACT_MASK_ENABLE BIT(1)
+#define B_AX_ENHANCED_BT BIT(0)
+
+#define R_AX_BT_STAST_HIGH 0xDA44
+#define B_AX_STATIS_BT_HI_RX_MASK GENMASK(31, 16)
+#define B_AX_STATIS_BT_HI_TX_MASK GENMASK(15, 0)
+#define R_AX_BT_STAST_LOW 0xDA48
+#define B_AX_STATIS_BT_LO_TX_1_MASK GENMASK(15, 0)
+#define B_AX_STATIS_BT_LO_RX_1_MASK GENMASK(31, 16)
+
+#define R_AX_TDMA_MODE 0xDA4C
+#define R_AX_TDMA_MODE_C1 0xFA4C
+#define B_AX_R_BT_CMD_RPT_MASK GENMASK(31, 16)
+#define B_AX_R_RPT_FROM_BT_MASK GENMASK(15, 8)
+#define B_AX_BT_HID_ISR_SET_MASK GENMASK(7, 6)
+#define B_AX_TDMA_BT_START_NOTIFY BIT(5)
+#define B_AX_ENABLE_TDMA_FW_MODE BIT(4)
+#define B_AX_ENABLE_PTA_TDMA_MODE BIT(3)
+#define B_AX_ENABLE_COEXIST_TAB_IN_TDMA BIT(2)
+#define B_AX_GPIO2_GPIO3_EXANGE_OR_NO_BT_CCA BIT(1)
+#define B_AX_RTK_BT_ENABLE BIT(0)
+
+#define R_AX_BT_COEX_CFG_5 0xDA6C
+#define R_AX_BT_COEX_CFG_5_C1 0xFA6C
+#define B_AX_BT_TIME_MASK GENMASK(31, 6)
+#define B_AX_BT_RPT_SAMPLE_RATE_MASK GENMASK(5, 0)
+#define MAC_AX_RTK_RATE 5
+
+#define R_AX_LTE_CTRL 0xDAF0
+#define R_AX_LTE_WDATA 0xDAF4
+#define R_AX_LTE_RDATA 0xDAF8
+
+#define CMAC1_START_ADDR 0xE000
+#define CMAC1_END_ADDR 0xFFFF
+#define R_AX_CMAC_REG_END 0xFFFF
+
+#define R_AX_LTE_SW_CFG_1 0x0038
+#define R_AX_LTE_SW_CFG_1_C1 0x2038
+#define B_AX_GNT_BT_RFC_S1_SW_VAL BIT(31)
+#define B_AX_GNT_BT_RFC_S1_SW_CTRL BIT(30)
+#define B_AX_GNT_WL_RFC_S1_SW_VAL BIT(29)
+#define B_AX_GNT_WL_RFC_S1_SW_CTRL BIT(28)
+#define B_AX_GNT_BT_BB_S1_SW_VAL BIT(27)
+#define B_AX_GNT_BT_BB_S1_SW_CTRL BIT(26)
+#define B_AX_GNT_WL_BB_S1_SW_VAL BIT(25)
+#define B_AX_GNT_WL_BB_S1_SW_CTRL BIT(24)
+#define B_AX_BT_SW_CTRL_WL_PRIORITY BIT(19)
+#define B_AX_WL_SW_CTRL_WL_PRIORITY BIT(18)
+#define B_AX_LTE_PATTERN_2_EN BIT(17)
+#define B_AX_LTE_PATTERN_1_EN BIT(16)
+#define B_AX_GNT_BT_RFC_S0_SW_VAL BIT(15)
+#define B_AX_GNT_BT_RFC_S0_SW_CTRL BIT(14)
+#define B_AX_GNT_WL_RFC_S0_SW_VAL BIT(13)
+#define B_AX_GNT_WL_RFC_S0_SW_CTRL BIT(12)
+#define B_AX_GNT_BT_BB_S0_SW_VAL BIT(11)
+#define B_AX_GNT_BT_BB_S0_SW_CTRL BIT(10)
+#define B_AX_GNT_WL_BB_S0_SW_VAL BIT(9)
+#define B_AX_GNT_WL_BB_S0_SW_CTRL BIT(8)
+#define B_AX_LTECOEX_FUN_EN BIT(7)
+#define B_AX_LTECOEX_3WIRE_CTRL_MUX BIT(6)
+#define B_AX_LTECOEX_OP_MODE_SEL_MASK GENMASK(5, 4)
+#define B_AX_LTECOEX_UART_MUX BIT(3)
+#define B_AX_LTECOEX_UART_MODE_SEL_MASK GENMASK(2, 0)
+
+#define R_AX_LTE_SW_CFG_2 0x003C
+#define R_AX_LTE_SW_CFG_2_C1 0x203C
+#define B_AX_WL_RX_CTRL BIT(8)
+#define B_AX_GNT_WL_RX_SW_VAL BIT(7)
+#define B_AX_GNT_WL_RX_SW_CTRL BIT(6)
+#define B_AX_GNT_WL_TX_SW_VAL BIT(5)
+#define B_AX_GNT_WL_TX_SW_CTRL BIT(4)
+#define B_AX_GNT_BT_RX_SW_VAL BIT(3)
+#define B_AX_GNT_BT_RX_SW_CTRL BIT(2)
+#define B_AX_GNT_BT_TX_SW_VAL BIT(1)
+#define B_AX_GNT_BT_TX_SW_CTRL BIT(0)
+
+#define RR_MOD 0x00
+#define RR_MOD_IQK GENMASK(19, 4)
+#define RR_MOD_DPK GENMASK(19, 5)
+#define RR_MOD_MASK GENMASK(19, 16)
+#define RR_MOD_V_DOWN 0x0
+#define RR_MOD_V_STANDBY 0x1
+#define RR_MOD_V_TX 0x2
+#define RR_MOD_V_RX 0x3
+#define RR_MOD_V_TXIQK 0x4
+#define RR_MOD_V_DPK 0x5
+#define RR_MOD_V_RXK1 0x6
+#define RR_MOD_V_RXK2 0x7
+#define RR_MOD_M_RXG GENMASK(13, 4)
+#define RR_MOD_M_RXBB GENMASK(9, 5)
+#define RR_MODOPT 0x01
+#define RR_MODOPT_M_TXPWR GENMASK(5, 0)
+#define RR_WLSEL 0x02
+#define RR_WLSEL_AG GENMASK(18, 16)
+#define RR_RSV1 0x05
+#define RR_RSV1_RST BIT(0)
+#define RR_DTXLOK 0x08
+#define RR_RSV2 0x09
+#define RR_CFGCH 0x18
+#define RR_BTC 0x1a
+#define RR_BTC_TXBB GENMASK(14, 12)
+#define RR_BTC_RXBB GENMASK(11, 10)
+#define RR_RCKC 0x1b
+#define RR_RCKC_CA GENMASK(14, 10)
+#define RR_RCKS 0x1c
+#define RR_RCKO 0x1d
+#define RR_RCKO_OFF GENMASK(13, 9)
+#define RR_RXKPLL 0x1e
+#define RR_RXKPLL_OFF GENMASK(5, 0)
+#define RR_RXKPLL_POW BIT(19)
+#define RR_RSV4 0x1f
+#define RR_RXK 0x20
+#define RR_RXK_PLLEN BIT(5)
+#define RR_RXK_SEL5G BIT(7)
+#define RR_RXK_SEL2G BIT(8)
+#define RR_LUTWA 0x33
+#define RR_LUTWA_MASK GENMASK(9, 0)
+#define RR_LUTWD1 0x3e
+#define RR_LUTWD0 0x3f
+#define RR_TM 0x42
+#define RR_TM_TRI BIT(19)
+#define RR_TM_VAL GENMASK(6, 1)
+#define RR_TM2 0x43
+#define RR_TM2_OFF GENMASK(19, 16)
+#define RR_TXG1 0x51
+#define RR_TXG1_ATT2 BIT(19)
+#define RR_TXG1_ATT1 BIT(11)
+#define RR_TXG2 0x52
+#define RR_TXG2_ATT0 BIT(11)
+#define RR_BSPAD 0x54
+#define RR_TXGA 0x55
+#define RR_TXGA_LOK_EN BIT(0)
+#define RR_TXGA_TRK_EN BIT(7)
+#define RR_GAINTX 0x56
+#define RR_GAINTX_ALL GENMASK(15, 0)
+#define RR_GAINTX_PAD GENMASK(9, 5)
+#define RR_GAINTX_BB GENMASK(4, 0)
+#define RR_TXMO 0x58
+#define RR_TXMO_COI GENMASK(19, 15)
+#define RR_TXMO_COQ GENMASK(14, 10)
+#define RR_TXMO_FII GENMASK(9, 6)
+#define RR_TXMO_FIQ GENMASK(5, 2)
+#define RR_TXA 0x5d
+#define RR_TXA_TRK GENMASK(19, 14)
+#define RR_TXRSV 0x5c
+#define RR_TXRSV_GAPK BIT(19)
+#define RR_BIAS 0x5e
+#define RR_BIAS_GAPK BIT(19)
+#define RR_BIASA 0x60
+#define RR_BIASA_TXG GENMASK(15, 12)
+#define RR_BIASA_TXA GENMASK(19, 16)
+#define RR_BIASA_A GENMASK(2, 0)
+#define RR_BIASA2 0x63
+#define RR_BIASA2_LB GENMASK(4, 2)
+#define RR_TXATANK 0x64
+#define RR_TXATANK_LBSW GENMASK(16, 15)
+#define RR_TRXIQ 0x66
+#define RR_RSV6 0x6d
+#define RR_TXPOW 0x7f
+#define RR_TXPOW_TXG BIT(1)
+#define RR_TXPOW_TXA BIT(8)
+#define RR_RXPOW 0x80
+#define RR_RXPOW_IQK GENMASK(17, 16)
+#define RR_RXBB 0x83
+#define RR_RXBB_C2G GENMASK(16, 10)
+#define RR_RXBB_C1G GENMASK(9, 8)
+#define RR_RXBB_ATTR GENMASK(7, 4)
+#define RR_RXBB_ATTC GENMASK(2, 0)
+#define RR_XGLNA2 0x85
+#define RR_XGLNA2_SW GENMASK(1, 0)
+#define RR_RXA 0x8a
+#define RR_RXA_DPK GENMASK(9, 8)
+#define RR_RXA2 0x8c
+#define RR_RXA2_C2 GENMASK(9, 3)
+#define RR_RXA2_C1 GENMASK(12, 10)
+#define RR_RXIQGEN 0x8d
+#define RR_RXIQGEN_ATTL GENMASK(12, 8)
+#define RR_RXIQGEN_ATTH GENMASK(14, 13)
+#define RR_RXBB2 0x8f
+#define RR_EN_TIA_IDA GENMASK(11, 10)
+#define RR_RXBB2_DAC_EN BIT(13)
+#define RR_XALNA2 0x90
+#define RR_XALNA2_SW GENMASK(1, 0)
+#define RR_DCK 0x92
+#define RR_DCK_FINE BIT(1)
+#define RR_DCK_LV BIT(0)
+#define RR_DCK1 0x93
+#define RR_DCK1_SEL BIT(3)
+#define RR_DCK2 0x94
+#define RR_DCK2_CYCLE GENMASK(7, 2)
+#define RR_MIXER 0x9f
+#define RR_MIXER_GN GENMASK(4, 3)
+#define RR_XTALX2 0xb8
+#define RR_MALSEL 0xbe
+#define RR_RCKD 0xde
+#define RR_RCKD_POW GENMASK(19, 13)
+#define RR_RCKD_BW BIT(2)
+#define RR_TXADBG 0xde
+#define RR_LUTDBG 0xdf
+#define RR_LUTDBG_LOK BIT(2)
+#define RR_LUTWE2 0xee
+#define RR_LUTWE 0xef
+#define RR_LUTWE_LOK BIT(2)
+#define RR_RFC 0xf0
+#define RR_RFC_CKEN BIT(1)
+
+#define R_UPD_P0 0x0000
+#define R_RSTB_WATCH_DOG 0x000C
+#define B_P0_RSTB_WATCH_DOG BIT(0)
+#define B_P1_RSTB_WATCH_DOG BIT(1)
+#define B_UPD_P0_EN BIT(30)
+#define R_ANAPAR_PW15 0x030C
+#define B_ANAPAR_PW15 GENMASK(31, 24)
+#define B_ANAPAR_PW15_H GENMASK(27, 24)
+#define B_ANAPAR_PW15_H2 GENMASK(27, 26)
+#define R_ANAPAR 0x032C
+#define B_ANAPAR_15 GENMASK(31, 16)
+#define B_ANAPAR_ADCCLK BIT(30)
+#define B_ANAPAR_FLTRST BIT(22)
+#define B_ANAPAR_CRXBB GENMASK(18, 16)
+#define B_ANAPAR_14 GENMASK(15, 0)
+#define R_UPD_CLK_ADC 0x0700
+#define B_UPD_CLK_ADC_ON BIT(24)
+#define B_UPD_CLK_ADC_VAL GENMASK(26, 25)
+#define R_RSTB_ASYNC 0x0704
+#define B_RSTB_ASYNC_ALL BIT(1)
+#define R_PMAC_GNT 0x0980
+#define B_PMAC_GNT_TXEN BIT(0)
+#define B_PMAC_GNT_RXEN BIT(16)
+#define B_PMAC_GNT_P1 GENMASK(20, 17)
+#define B_PMAC_GNT_P2 GENMASK(29, 26)
+#define R_PMAC_RX_CFG1 0x0988
+#define B_PMAC_OPT1_MSK GENMASK(11, 0)
+#define R_PMAC_RXMOD 0x0994
+#define B_PMAC_RXMOD_MSK GENMASK(7, 4)
+#define R_MAC_SEL 0x09A4
+#define B_MAC_SEL_MOD GENMASK(4, 2)
+#define B_MAC_SEL_DPD_EN BIT(10)
+#define B_MAC_SEL_PWR_EN BIT(16)
+#define R_PMAC_TX_CTRL 0x09C0
+#define B_PMAC_TXEN_DIS BIT(0)
+#define R_PMAC_TX_PRD 0x09C4
+#define B_PMAC_TX_PRD_MSK GENMASK(31, 8)
+#define B_PMAC_CTX_EN BIT(0)
+#define B_PMAC_PTX_EN BIT(4)
+#define R_PMAC_TX_CNT 0x09C8
+#define B_PMAC_TX_CNT_MSK GENMASK(31, 0)
+#define R_CCX 0x0C00
+#define B_CCX_EDCCA_OPT_MSK GENMASK(6, 4)
+#define B_MEASUREMENT_TRIG_MSK BIT(2)
+#define B_CCX_TRIG_OPT_MSK BIT(1)
+#define B_CCX_EN_MSK BIT(0)
+#define R_IFS_COUNTER 0x0C28
+#define B_IFS_CLM_PERIOD_MSK GENMASK(31, 16)
+#define B_IFS_CLM_COUNTER_UNIT_MSK GENMASK(15, 14)
+#define B_IFS_COUNTER_CLR_MSK BIT(13)
+#define B_IFS_COLLECT_EN BIT(12)
+#define R_IFS_T1 0x0C2C
+#define B_IFS_T1_TH_HIGH_MSK GENMASK(31, 16)
+#define B_IFS_T1_EN_MSK BIT(15)
+#define B_IFS_T1_TH_LOW_MSK GENMASK(14, 0)
+#define R_IFS_T2 0x0C30
+#define B_IFS_T2_TH_HIGH_MSK GENMASK(31, 16)
+#define B_IFS_T2_EN_MSK BIT(15)
+#define B_IFS_T2_TH_LOW_MSK GENMASK(14, 0)
+#define R_IFS_T3 0x0C34
+#define B_IFS_T3_TH_HIGH_MSK GENMASK(31, 16)
+#define B_IFS_T3_EN_MSK BIT(15)
+#define B_IFS_T3_TH_LOW_MSK GENMASK(14, 0)
+#define R_IFS_T4 0x0C38
+#define B_IFS_T4_TH_HIGH_MSK GENMASK(31, 16)
+#define B_IFS_T4_EN_MSK BIT(15)
+#define B_IFS_T4_TH_LOW_MSK GENMASK(14, 0)
+#define R_PD_CTRL 0x0C3C
+#define B_PD_HIT_DIS BIT(9)
+#define R_IOQ_IQK_DPK 0x0C60
+#define B_IOQ_IQK_DPK_EN BIT(1)
+#define R_P0_EN_SOUND_WO_NDP 0x0D7C
+#define B_P0_EN_SOUND_WO_NDP BIT(1)
+#define R_SPOOF_ASYNC_RST 0x0D84
+#define B_SPOOF_ASYNC_RST BIT(15)
+#define R_NDP_BRK0 0xDA0
+#define R_NDP_BRK1 0xDA4
+#define B_NDP_RU_BRK BIT(0)
+#define R_BRK_ASYNC_RST_EN_1 0x0DC0
+#define R_BRK_ASYNC_RST_EN_2 0x0DC4
+#define R_BRK_ASYNC_RST_EN_3 0x0DC8
+#define R_P0_RXCK 0x12A0
+#define B_P0_RXCK_VAL GENMASK(18, 16)
+#define B_P0_RXCK_ON BIT(19)
+#define B_P0_RXCK_BW3 BIT(30)
+#define R_P0_NRBW 0x12B8
+#define B_P0_NRBW_DBG BIT(30)
+#define R_S0_RXDC 0x12D4
+#define B_S0_RXDC_I GENMASK(25, 16)
+#define B_S0_RXDC_Q GENMASK(31, 26)
+#define R_S0_RXDC2 0x12D8
+#define B_S0_RXDC2_SEL GENMASK(9, 8)
+#define B_S0_RXDC2_AVG GENMASK(7, 6)
+#define B_S0_RXDC2_MEN GENMASK(5, 4)
+#define B_S0_RXDC2_Q2 GENMASK(3, 0)
+#define R_CFO_COMP_SEG0_L 0x1384
+#define R_CFO_COMP_SEG0_H 0x1388
+#define R_CFO_COMP_SEG0_CTRL 0x138C
+#define R_DBG32_D 0x1730
+#define R_TX_COUNTER 0x1A40
+#define R_IFS_CLM_TX_CNT 0x1ACC
+#define B_IFS_CLM_EDCCA_EXCLUDE_CCA_FA_MSK GENMASK(31, 16)
+#define B_IFS_CLM_TX_CNT_MSK GENMASK(15, 0)
+#define R_IFS_CLM_CCA 0x1AD0
+#define B_IFS_CLM_OFDMCCA_EXCLUDE_FA_MSK GENMASK(31, 16)
+#define B_IFS_CLM_CCKCCA_EXCLUDE_FA_MSK GENMASK(15, 0)
+#define R_IFS_CLM_FA 0x1AD4
+#define B_IFS_CLM_OFDM_FA_MSK GENMASK(31, 16)
+#define B_IFS_CLM_CCK_FA_MSK GENMASK(15, 0)
+#define R_IFS_HIS 0x1AD8
+#define B_IFS_T4_HIS_MSK GENMASK(31, 24)
+#define B_IFS_T3_HIS_MSK GENMASK(23, 16)
+#define B_IFS_T2_HIS_MSK GENMASK(15, 8)
+#define B_IFS_T1_HIS_MSK GENMASK(7, 0)
+#define R_IFS_AVG_L 0x1ADC
+#define B_IFS_T2_AVG_MSK GENMASK(31, 16)
+#define B_IFS_T1_AVG_MSK GENMASK(15, 0)
+#define R_IFS_AVG_H 0x1AE0
+#define B_IFS_T4_AVG_MSK GENMASK(31, 16)
+#define B_IFS_T3_AVG_MSK GENMASK(15, 0)
+#define R_IFS_CCA_L 0x1AE4
+#define B_IFS_T2_CCA_MSK GENMASK(31, 16)
+#define B_IFS_T1_CCA_MSK GENMASK(15, 0)
+#define R_IFS_CCA_H 0x1AE8
+#define B_IFS_T4_CCA_MSK GENMASK(31, 16)
+#define B_IFS_T3_CCA_MSK GENMASK(15, 0)
+#define R_IFSCNT 0x1AEC
+#define B_IFSCNT_DONE_MSK BIT(16)
+#define B_IFSCNT_TOTAL_CNT_MSK GENMASK(15, 0)
+#define R_TXAGC_TP 0x1C04
+#define B_TXAGC_TP GENMASK(2, 0)
+#define R_TSSI_THER 0x1C10
+#define B_TSSI_THER GENMASK(29, 24)
+#define R_TXAGC_BB 0x1C60
+#define B_TXAGC_BB_OFT GENMASK(31, 16)
+#define B_TXAGC_BB GENMASK(31, 24)
+#define R_S0_ADDCK 0x1E00
+#define B_S0_ADDCK_I GENMASK(9, 0)
+#define B_S0_ADDCK_Q GENMASK(19, 10)
+#define R_ADC_FIFO 0x20fc
+#define B_ADC_FIFO_RST GENMASK(31, 24)
+#define R_TXFIR0 0x2300
+#define B_TXFIR_C01 GENMASK(23, 0)
+#define R_TXFIR2 0x2304
+#define B_TXFIR_C23 GENMASK(23, 0)
+#define R_TXFIR4 0x2308
+#define B_TXFIR_C45 GENMASK(23, 0)
+#define R_TXFIR6 0x230c
+#define B_TXFIR_C67 GENMASK(23, 0)
+#define R_TXFIR8 0x2310
+#define B_TXFIR_C89 GENMASK(23, 0)
+#define R_TXFIRA 0x2314
+#define B_TXFIR_CAB GENMASK(23, 0)
+#define R_TXFIRC 0x2318
+#define B_TXFIR_CCD GENMASK(23, 0)
+#define R_TXFIRE 0x231c
+#define B_TXFIR_CEF GENMASK(23, 0)
+#define R_RXCCA 0x2344
+#define B_RXCCA_DIS BIT(31)
+#define R_RXSC 0x237C
+#define B_RXSC_EN BIT(0)
+#define R_RXSCOBC 0x23B0
+#define B_RXSCOBC_TH GENMASK(18, 0)
+#define R_RXSCOCCK 0x23B4
+#define B_RXSCOCCK_TH GENMASK(18, 0)
+#define R_P1_EN_SOUND_WO_NDP 0x2D7C
+#define B_P1_EN_SOUND_WO_NDP BIT(1)
+#define R_P1_DBGMOD 0x32B8
+#define B_P1_DBGMOD_ON BIT(30)
+#define R_S1_RXDC 0x32D4
+#define B_S1_RXDC_I GENMASK(25, 16)
+#define B_S1_RXDC_Q GENMASK(31, 26)
+#define R_S1_RXDC2 0x32D8
+#define B_S1_RXDC2_EN GENMASK(5, 4)
+#define B_S1_RXDC2_SEL GENMASK(9, 8)
+#define B_S1_RXDC2_Q2 GENMASK(3, 0)
+#define R_TXAGC_BB_S1 0x3C60
+#define B_TXAGC_BB_S1_OFT GENMASK(31, 16)
+#define B_TXAGC_BB_S1 GENMASK(31, 24)
+#define R_S1_ADDCK 0x3E00
+#define B_S1_ADDCK_I GENMASK(9, 0)
+#define B_S1_ADDCK_Q GENMASK(19, 10)
+#define R_DCFO 0x4264
+#define B_DCFO GENMASK(1, 0)
+#define R_SEG0CSI 0x42AC
+#define B_SEG0CSI_IDX GENMASK(10, 0)
+#define R_SEG0CSI_EN 0x42C4
+#define B_SEG0CSI_EN BIT(23)
+#define R_BSS_CLR_MAP 0x43ac
+#define B_BSS_CLR_MAP_VLD0 BIT(28)
+#define B_BSS_CLR_MAP_TGT GENMASK(27, 22)
+#define B_BSS_CLR_MAP_STAID GENMASK(21, 11)
+#define R_CFO_TRK0 0x4404
+#define R_CFO_TRK1 0x440C
+#define B_CFO_TRK_MSK GENMASK(14, 10)
+#define R_DCFO_COMP_S0 0x448C
+#define B_DCFO_COMP_S0_MSK GENMASK(11, 0)
+#define R_DCFO_WEIGHT 0x4490
+#define B_DCFO_WEIGHT_MSK GENMASK(27, 24)
+#define R_DCFO_OPT 0x4494
+#define B_DCFO_OPT_EN BIT(29)
+#define R_BANDEDGE 0x4498
+#define B_BANDEDGE_EN BIT(30)
+#define R_TXPATH_SEL 0x458C
+#define B_TXPATH_SEL_MSK GENMASK(31, 28)
+#define R_TXPWR 0x4594
+#define B_TXPWR_MSK GENMASK(30, 22)
+#define R_TXNSS_MAP 0x45B4
+#define B_TXNSS_MAP_MSK GENMASK(20, 17)
+#define R_PATH0_IB_PKPW 0x4628
+#define B_PATH0_IB_PKPW_MSK GENMASK(11, 6)
+#define R_PATH0_LNA_ERR1 0x462C
+#define B_PATH0_LNA_ERR_G1_A_MSK GENMASK(29, 24)
+#define B_PATH0_LNA_ERR_G0_G_MSK GENMASK(17, 12)
+#define B_PATH0_LNA_ERR_G0_A_MSK GENMASK(11, 6)
+#define R_PATH0_LNA_ERR2 0x4630
+#define B_PATH0_LNA_ERR_G2_G_MSK GENMASK(23, 18)
+#define B_PATH0_LNA_ERR_G2_A_MSK GENMASK(17, 12)
+#define B_PATH0_LNA_ERR_G1_G_MSK GENMASK(5, 0)
+#define R_PATH0_LNA_ERR3 0x4634
+#define B_PATH0_LNA_ERR_G4_G_MSK GENMASK(29, 24)
+#define B_PATH0_LNA_ERR_G4_A_MSK GENMASK(23, 18)
+#define B_PATH0_LNA_ERR_G3_G_MSK GENMASK(11, 6)
+#define B_PATH0_LNA_ERR_G3_A_MSK GENMASK(5, 0)
+#define R_PATH0_LNA_ERR4 0x4638
+#define B_PATH0_LNA_ERR_G6_A_MSK GENMASK(29, 24)
+#define B_PATH0_LNA_ERR_G5_G_MSK GENMASK(17, 12)
+#define B_PATH0_LNA_ERR_G5_A_MSK GENMASK(11, 6)
+#define R_PATH0_LNA_ERR5 0x463C
+#define B_PATH0_LNA_ERR_G6_G_MSK GENMASK(5, 0)
+#define R_PATH0_TIA_ERR_G0 0x4640
+#define B_PATH0_TIA_ERR_G0_G_MSK GENMASK(23, 18)
+#define B_PATH0_TIA_ERR_G0_A_MSK GENMASK(17, 12)
+#define R_PATH0_TIA_ERR_G1 0x4644
+#define B_PATH0_TIA_ERR_G1_SEL GENMASK(31, 30)
+#define B_PATH0_TIA_ERR_G1_G_MSK GENMASK(11, 6)
+#define B_PATH0_TIA_ERR_G1_A_MSK GENMASK(5, 0)
+#define R_PATH0_IB_PBK 0x4650
+#define B_PATH0_IB_PBK_MSK GENMASK(14, 10)
+#define R_PATH0_RXB_INIT 0x4658
+#define B_PATH0_RXB_INIT_IDX_MSK GENMASK(9, 5)
+#define R_PATH0_LNA_INIT 0x4668
+#define B_PATH0_LNA_INIT_IDX_MSK GENMASK(26, 24)
+#define R_PATH0_BTG 0x466C
+#define B_PATH0_BTG_SHEN GENMASK(18, 17)
+#define R_PATH0_TIA_INIT 0x4674
+#define B_PATH0_TIA_INIT_IDX_MSK BIT(17)
+#define R_PATH0_P20_FOLLOW_BY_PAGCUGC 0x46A0
+#define B_PATH0_P20_FOLLOW_BY_PAGCUGC_EN_MSK BIT(5)
+#define R_PATH0_S20_FOLLOW_BY_PAGCUGC 0x46A4
+#define B_PATH0_S20_FOLLOW_BY_PAGCUGC_EN_MSK BIT(5)
+#define R_P0_NBIIDX 0x469C
+#define B_P0_NBIIDX_VAL GENMASK(11, 0)
+#define B_P0_NBIIDX_NOTCH_EN BIT(12)
+#define R_P1_MODE 0x4718
+#define B_P1_MODE_SEL GENMASK(31, 30)
+#define R_PATH1_LNA_INIT 0x473C
+#define B_PATH1_LNA_INIT_IDX_MSK GENMASK(26, 24)
+#define R_PATH1_TIA_INIT 0x4748
+#define B_PATH1_TIA_INIT_IDX_MSK BIT(17)
+#define R_PATH1_BTG 0x4740
+#define B_PATH1_BTG_SHEN GENMASK(18, 17)
+#define R_PATH1_RXB_INIT 0x472C
+#define B_PATH1_RXB_INIT_IDX_MSK GENMASK(9, 5)
+#define R_PATH1_P20_FOLLOW_BY_PAGCUGC 0x4774
+#define B_PATH1_P20_FOLLOW_BY_PAGCUGC_EN_MSK BIT(5)
+#define R_PATH1_S20_FOLLOW_BY_PAGCUGC 0x4778
+#define B_PATH1_S20_FOLLOW_BY_PAGCUGC_EN_MSK BIT(5)
+#define R_P1_NBIIDX 0x4770
+#define B_P1_NBIIDX_VAL GENMASK(11, 0)
+#define B_P1_NBIIDX_NOTCH_EN BIT(12)
+#define R_SEG0R_PD 0x481C
+#define B_SEG0R_PD_SPATIAL_REUSE_EN_MSK BIT(29)
+#define B_SEG0R_PD_LOWER_BOUND_MSK GENMASK(10, 6)
+#define R_2P4G_BAND 0x4970
+#define B_2P4G_BAND_SEL BIT(1)
+#define R_FC0_BW 0x4974
+#define B_FC0_BW_INV GENMASK(6, 0)
+#define B_FC0_BW_SET GENMASK(31, 30)
+#define R_CHBW_MOD 0x4978
+#define B_CHBW_MOD_PRICH GENMASK(11, 8)
+#define B_CHBW_MOD_SBW GENMASK(13, 12)
+#define R_CFO_COMP_SEG1_L 0x5384
+#define R_CFO_COMP_SEG1_H 0x5388
+#define R_CFO_COMP_SEG1_CTRL 0x538C
+#define B_CFO_COMP_VALID_BIT BIT(29)
+#define B_CFO_COMP_WEIGHT_MSK GENMASK(27, 24)
+#define B_CFO_COMP_VAL_MSK GENMASK(11, 0)
+#define R_DPD_OFT_EN 0x5800
+#define B_DPD_OFT_EN BIT(28)
+#define R_DPD_OFT_ADDR 0x5804
+#define B_DPD_OFT_ADDR GENMASK(31, 27)
+#define R_P0_TMETER 0x5810
+#define B_P0_TMETER GENMASK(15, 10)
+#define B_P0_TMETER_DIS BIT(16)
+#define B_P0_TMETER_TRK BIT(24)
+#define R_P0_TSSI_TRK 0x5818
+#define B_P0_TSSI_TRK_EN BIT(30)
+#define B_P0_TSSI_OFT_EN BIT(28)
+#define B_P0_TSSI_OFT GENMASK(7, 0)
+#define R_P0_TSSI_AVG 0x5820
+#define B_P0_TSSI_AVG GENMASK(15, 12)
+#define R_P0_RFCTM 0x5864
+#define B_P0_RFCTM_VAL GENMASK(25, 20)
+#define R_P0_RFCTM_RDY BIT(26)
+#define R_P0_TXDPD 0x58D4
+#define B_P0_TXDPD GENMASK(31, 28)
+#define R_P0_TXPW_RSTB 0x58DC
+#define B_P0_TXPW_RSTB_MANON BIT(30)
+#define B_P0_TXPW_RSTB_TSSI BIT(31)
+#define R_P0_TSSI_MV_AVG 0x58E4
+#define B_P0_TSSI_MV_AVG GENMASK(13, 11)
+#define R_TXGAIN_SCALE 0x58F0
+#define B_TXGAIN_SCALE_EN BIT(19)
+#define B_TXGAIN_SCALE_OFT GENMASK(31, 24)
+#define R_P0_TSSI_BASE 0x5C00
+#define R_S0_DACKI 0x5E00
+#define B_S0_DACKI_AR GENMASK(31, 28)
+#define B_S0_DACKI_EN BIT(3)
+#define R_S0_DACKI2 0x5E30
+#define B_S0_DACKI2_K GENMASK(21, 12)
+#define R_S0_DACKI7 0x5E44
+#define B_S0_DACKI7_K GENMASK(15, 8)
+#define R_S0_DACKI8 0x5E48
+#define B_S0_DACKI8_K GENMASK(15, 8)
+#define R_S0_DACKQ 0x5E50
+#define B_S0_DACKQ_AR GENMASK(31, 28)
+#define B_S0_DACKQ_EN BIT(3)
+#define R_S0_DACKQ2 0x5E80
+#define B_S0_DACKQ2_K GENMASK(21, 12)
+#define R_S0_DACKQ7 0x5E94
+#define B_S0_DACKQ7_K GENMASK(15, 8)
+#define R_S0_DACKQ8 0x5E98
+#define B_S0_DACKQ8_K GENMASK(15, 8)
+#define R_P1_TMETER 0x7810
+#define B_P1_TMETER GENMASK(15, 10)
+#define B_P1_TMETER_DIS BIT(16)
+#define B_P1_TMETER_TRK BIT(24)
+#define R_P1_TSSI_TRK 0x7818
+#define B_P1_TSSI_TRK_EN BIT(30)
+#define B_P1_TSSI_OFT_EN BIT(28)
+#define B_P1_TSSI_OFT GENMASK(7, 0)
+#define R_P1_TSSI_AVG 0x7820
+#define B_P1_TSSI_AVG GENMASK(15, 12)
+#define R_P1_RFCTM 0x7864
+#define R_P1_RFCTM_RDY BIT(26)
+#define B_P1_RFCTM_VAL GENMASK(25, 20)
+#define R_P1_TXPW_RSTB 0x78DC
+#define B_P1_TXPW_RSTB_MANON BIT(30)
+#define B_P1_TXPW_RSTB_TSSI BIT(31)
+#define R_P1_TSSI_MV_AVG 0x78E4
+#define B_P1_TSSI_MV_AVG GENMASK(13, 11)
+#define R_TSSI_THOF 0x7C00
+#define R_S1_DACKI 0x7E00
+#define B_S1_DACKI_AR GENMASK(31, 28)
+#define B_S1_DACKI_EN BIT(3)
+#define R_S1_DACKI2 0x7E30
+#define B_S1_DACKI2_K GENMASK(21, 12)
+#define R_S1_DACKI7 0x7E44
+#define B_S1_DACKI_K GENMASK(15, 8)
+#define R_S1_DACKI8 0x7E48
+#define B_S1_DACKI8_K GENMASK(15, 8)
+#define R_S1_DACKQ 0x7E50
+#define B_S1_DACKQ_AR GENMASK(31, 28)
+#define B_S1_DACKQ_EN BIT(3)
+#define R_S1_DACKQ2 0x7E80
+#define B_S1_DACKQ2_K GENMASK(21, 12)
+#define R_S1_DACKQ7 0x7E94
+#define B_S1_DACKQ7_K GENMASK(15, 8)
+#define R_S1_DACKQ8 0x7E98
+#define B_S1_DACKQ8_K GENMASK(15, 8)
+#define R_NCTL_CFG 0x8000
+#define B_NCTL_CFG_SPAGE GENMASK(2, 1)
+#define R_NCTL_RPT 0x8008
+#define B_NCTL_RPT_FLG BIT(26)
+#define R_NCTL_N1 0x8010
+#define B_NCTL_N1_CIP GENMASK(7, 0)
+#define R_NCTL_N2 0x8014
+#define R_IQK_COM 0x8018
+#define R_IQK_DIF 0x801C
+#define B_IQK_DIF_TRX GENMASK(1, 0)
+#define R_IQK_DIF1 0x8020
+#define B_IQK_DIF1_TXPI GENMASK(19, 0)
+#define R_IQK_DIF2 0x8024
+#define B_IQK_DIF2_RXPI GENMASK(19, 0)
+#define R_IQK_DIF4 0x802C
+#define B_IQK_DIF4_TXT GENMASK(11, 0)
+#define B_IQK_DIF4_RXT GENMASK(27, 16)
+#define R_IQK_CFG 0x8034
+#define B_IQK_CFG_SET GENMASK(5, 4)
+#define R_TPG_MOD 0x806C
+#define B_TPG_MOD_F GENMASK(2, 1)
+#define R_MDPK_SYNC 0x8070
+#define B_MDPK_SYNC_SEL BIT(31)
+#define B_MDPK_SYNC_MAN GENMASK(31, 28)
+#define R_MDPK_RX_DCK 0x8074
+#define R_NCTL_RW 0x8080
+#define R_KIP_SYSCFG 0x8088
+#define R_KIP_CLK 0x808C
+#define R_LDL_NORM 0x80A0
+#define B_LDL_NORM_PN GENMASK(12, 8)
+#define B_LDL_NORM_OP GENMASK(1, 0)
+#define R_DPK_CTL 0x80B0
+#define B_DPK_CTL_EN BIT(28)
+#define R_DPK_CFG 0x80B8
+#define B_DPK_CFG_IDX GENMASK(14, 12)
+#define R_DPK_CFG2 0x80BC
+#define B_DPK_CFG2_ST BIT(14)
+#define R_DPK_CFG3 0x80C0
+#define R_KPATH_CFG 0x80D0
+#define R_KIP_RPT1 0x80D4
+#define B_KIP_RPT1_SEL GENMASK(21, 16)
+#define R_SRAM_IQRX 0x80D8
+#define R_GAPK 0x80E0
+#define B_GAPK_ADR BIT(0)
+#define R_SRAM_IQRX2 0x80E8
+#define R_DPK_TRK 0x80f0
+#define B_DPK_TRK_DIS BIT(31)
+#define R_RPT_COM 0x80FC
+#define B_PRT_COM_SYNERR BIT(30)
+#define B_PRT_COM_DCI GENMASK(27, 16)
+#define B_PRT_COM_CORV GENMASK(15, 8)
+#define B_PRT_COM_DCQ GENMASK(11, 0)
+#define B_PRT_COM_GL GENMASK(7, 4)
+#define B_PRT_COM_CORI GENMASK(7, 0)
+#define R_COEF_SEL 0x8104
+#define B_COEF_SEL_IQC BIT(0)
+#define B_COEF_SEL_MDPD BIT(8)
+#define R_CFIR_SYS 0x8120
+#define R_IQK_RES 0x8124
+#define B_IQK_RES_TXCFIR GENMASK(11, 8)
+#define B_IQK_RES_RXCFIR GENMASK(3, 0)
+#define R_TXIQC 0x8138
+#define R_RXIQC 0x813c
+#define B_RXIQC_BYPASS BIT(0)
+#define B_RXIQC_BYPASS2 BIT(2)
+#define B_RXIQC_NEWP GENMASK(19, 8)
+#define B_RXIQC_NEWX GENMASK(31, 20)
+#define R_KIP 0x8140
+#define B_KIP_DBCC BIT(0)
+#define B_KIP_RFGAIN BIT(8)
+#define R_RFGAIN 0x8144
+#define B_RFGAIN_PAD GENMASK(4, 0)
+#define B_RFGAIN_TXBB GENMASK(12, 8)
+#define R_RFGAIN_BND 0x8148
+#define B_RFGAIN_BND GENMASK(4, 0)
+#define R_CFIR_MAP 0x8150
+#define R_CFIR_LUT 0x8154
+#define B_CFIR_LUT_SEL BIT(8)
+#define B_CFIR_LUT_G3 BIT(3)
+#define B_CFIR_LUT_G2 BIT(2)
+#define B_CFIR_LUT_GP GENMASK(1, 0)
+#define R_DPD_V1 0x81a0
+#define R_DPD_CH0 0x81AC
+#define R_DPD_BND 0x81B4
+#define R_DPD_CH0A 0x81BC
+#define R_TXAGC_RFK 0x81C4
+#define B_TXAGC_RFK_CH0 GENMASK(5, 0)
+#define R_DPD_COM 0x81C8
+#define R_KIP_IQP 0x81CC
+#define B_KIP_IQP_IQSW GENMASK(5, 0)
+#define R_KIP_RPT 0x81D4
+#define B_KIP_RPT_SEL GENMASK(21, 16)
+#define R_W_COEF 0x81D8
+#define R_LOAD_COEF 0x81DC
+#define B_LOAD_COEF_MDPD BIT(16)
+#define B_LOAD_COEF_CFIR GENMASK(1, 0)
+#define B_LOAD_COEF_AUTO BIT(0)
+#define R_RPT_PER 0x81FC
+#define R_RXCFIR_P0C0 0x8D40
+#define R_RXCFIR_P0C1 0x8D84
+#define R_RXCFIR_P0C2 0x8DC8
+#define R_RXCFIR_P0C3 0x8E0C
+#define R_TXCFIR_P0C0 0x8F50
+#define R_TXCFIR_P0C1 0x8F84
+#define R_TXCFIR_P0C2 0x8FB8
+#define R_TXCFIR_P0C3 0x8FEC
+#define R_RXCFIR_P1C0 0x9140
+#define R_RXCFIR_P1C1 0x9184
+#define R_RXCFIR_P1C2 0x91C8
+#define R_RXCFIR_P1C3 0x920C
+#define R_TXCFIR_P1C0 0x9350
+#define R_TXCFIR_P1C1 0x9384
+#define R_TXCFIR_P1C2 0x93B8
+#define R_TXCFIR_P1C3 0x93EC
+#define R_IQKINF 0x9FE0
+#define B_IQKINF_VER GENMASK(31, 24)
+#define B_IQKINF_FAIL_RXGRP GENMASK(23, 16)
+#define B_IQKINF_FAIL_TXGRP GENMASK(15, 8)
+#define B_IQKINF_FAIL GENMASK(3, 0)
+#define B_IQKINF_F_RX BIT(3)
+#define B_IQKINF_FTX BIT(2)
+#define B_IQKINF_FFIN BIT(1)
+#define B_IQKINF_FCOR BIT(0)
+#define R_IQKCH 0x9FE4
+#define B_IQKCH_CH GENMASK(15, 8)
+#define B_IQKCH_BW GENMASK(7, 4)
+#define B_IQKCH_BAND GENMASK(3, 0)
+#define R_IQKINF2 0x9FE8
+#define B_IQKINF2_FCNT GENMASK(23, 16)
+#define B_IQKINF2_KCNT GENMASK(15, 8)
+#define B_IQKINF2_NCTLV GENMAKS(7, 0)
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/regd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/regd.c
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "debug.h"
+#include "ps.h"
+
+#define COUNTRY_REGD(_alpha2, _txpwr_regd_2g, _txpwr_regd_5g) \
+	{.alpha2 = (_alpha2), \
+	 .txpwr_regd[RTW89_BAND_2G] = (_txpwr_regd_2g), \
+	 .txpwr_regd[RTW89_BAND_5G] = (_txpwr_regd_5g) \
+	}
+
+static const struct rtw89_regulatory rtw89_ww_regd =
+	COUNTRY_REGD("00", RTW89_WW, RTW89_WW);
+
+static const struct rtw89_regulatory rtw89_regd_map[] = {
+	COUNTRY_REGD("AR", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BO", RTW89_WW, RTW89_FCC),
+	COUNTRY_REGD("BR", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("CL", RTW89_WW, RTW89_CHILE),
+	COUNTRY_REGD("CO", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("CR", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("EC", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("SV", RTW89_WW, RTW89_FCC),
+	COUNTRY_REGD("GT", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("HN", RTW89_WW, RTW89_FCC),
+	COUNTRY_REGD("MX", RTW89_FCC, RTW89_MEXICO),
+	COUNTRY_REGD("NI", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("PA", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("PY", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("PE", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("US", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("UY", RTW89_WW, RTW89_FCC),
+	COUNTRY_REGD("VE", RTW89_WW, RTW89_FCC),
+	COUNTRY_REGD("PR", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("DO", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("AT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CY", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("DK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("EE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("FI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("FR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("DE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("HU", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IS", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LV", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LU", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MC", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NL", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("PL", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("PT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ES", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GB", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AL", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("HR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("EG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IQ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IL", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("JO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KW", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LB", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LS", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("OM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("QA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("RO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("RU", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("RS", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ME", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ZA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("UA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("YE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ZW", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BD", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("HK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ID", RTW89_ETSI, RTW89_ETSI),
+	COUNTRY_REGD("KR", RTW89_KCC, RTW89_KCC),
+	COUNTRY_REGD("MY", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("PK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("PH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TW", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("TH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("VN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AU", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("NZ", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("PG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CA", RTW89_IC, RTW89_IC),
+	COUNTRY_REGD("JP", RTW89_MKK, RTW89_MKK),
+	COUNTRY_REGD("JM", RTW89_WW, RTW89_FCC),
+	COUNTRY_REGD("AN", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("TT", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("TN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AF", RTW89_ETSI, RTW89_ETSI),
+	COUNTRY_REGD("DZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AS", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("AD", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AQ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AG", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("AM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("AW", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BS", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BB", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BY", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BZ", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BJ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BM", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BW", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BV", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("VG", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("BN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BF", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("BI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CV", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KY", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("CF", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TD", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CX", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("CC", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CD", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("CI", RTW89_ETSI, RTW89_ETSI),
+	COUNTRY_REGD("DJ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("DM", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("GQ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ER", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ET", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("FK", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("FO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("FJ", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("GF", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("PF", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TF", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GL", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GD", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("GP", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GU", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("GG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GW", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GY", RTW89_FCC, RTW89_NCC),
+	COUNTRY_REGD("HT", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("HM", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("VA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("JE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KI", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LA", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("LY", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MW", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MV", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ML", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MH", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("MQ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MU", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("YT", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("FM", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("MD", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MN", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("MS", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NR", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NP", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NC", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("NU", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("NF", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("MP", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("PW", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("RE", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("RW", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("KN", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("LC", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("MF", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("SX", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("PM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("VC", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("WS", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("SM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ST", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("SC", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("SL", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SB", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("GS", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SR", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("SJ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("SZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TJ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TK", RTW89_WW, RTW89_ACMA),
+	COUNTRY_REGD("TO", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TC", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("TV", RTW89_ETSI, RTW89_NA),
+	COUNTRY_REGD("UG", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("VI", RTW89_FCC, RTW89_FCC),
+	COUNTRY_REGD("UZ", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("VU", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("WF", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("EH", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("ZM", RTW89_WW, RTW89_ETSI),
+	COUNTRY_REGD("IR", RTW89_WW, RTW89_ETSI),
+};
+
+static const struct rtw89_regulatory *rtw89_regd_find_reg_by_name(char *alpha2)
+{
+	u32 i;
+
+	for (i = 0; i < ARRAY_SIZE(rtw89_regd_map); i++) {
+		if (!memcmp(rtw89_regd_map[i].alpha2, alpha2, 2))
+			return &rtw89_regd_map[i];
+	}
+
+	return &rtw89_ww_regd;
+}
+
+static bool rtw89_regd_is_ww(const struct rtw89_regulatory *regd)
+{
+	return regd == &rtw89_ww_regd;
+}
+
+int rtw89_regd_init(struct rtw89_dev *rtwdev,
+		    void (*reg_notifier)(struct wiphy *wiphy,
+					 struct regulatory_request *request))
+{
+	const struct rtw89_regulatory *chip_regd;
+	struct wiphy *wiphy = rtwdev->hw->wiphy;
+	int ret;
+
+	if (!wiphy)
+		return -EINVAL;
+
+	chip_regd = rtw89_regd_find_reg_by_name(rtwdev->efuse.country_code);
+	if (!rtw89_regd_is_ww(chip_regd)) {
+		rtwdev->regd = chip_regd;
+		/* Ignore country ie if there is a country domain programmed in chip */
+		wiphy->regulatory_flags |= REGULATORY_COUNTRY_IE_IGNORE;
+		wiphy->regulatory_flags |= REGULATORY_STRICT_REG;
+
+		ret = regulatory_hint(rtwdev->hw->wiphy, rtwdev->regd->alpha2);
+		if (ret)
+			rtw89_warn(rtwdev, "failed to hint regulatory:%d\n", ret);
+
+		rtw89_debug(rtwdev, RTW89_DBG_REGD,
+			    "efuse country code %c%c, mapping to 2g txregd %d, 5g txregd %d\n",
+			    rtwdev->efuse.country_code[0], rtwdev->efuse.country_code[1],
+			    rtwdev->regd->txpwr_regd[RTW89_BAND_2G],
+			    rtwdev->regd->txpwr_regd[RTW89_BAND_5G]);
+
+		return 0;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_REGD,
+		    "worldwide roaming chip, follow the setting of stack(%c%c), mapping to 2g txregd %d, 5g txregd %d\n",
+		     rtwdev->regd->alpha2[0], rtwdev->regd->alpha2[1],
+		     rtwdev->regd->txpwr_regd[RTW89_BAND_2G],
+		     rtwdev->regd->txpwr_regd[RTW89_BAND_5G]);
+
+	return 0;
+}
+
+static void rtw89_regd_notifier_apply(struct rtw89_dev *rtwdev,
+				      struct wiphy *wiphy,
+				      struct regulatory_request *request)
+{
+	rtwdev->regd = rtw89_regd_find_reg_by_name(request->alpha2);
+	/* This notification might be set from the system of distros,
+	 * and it does not expect the regulatory will be modified by
+	 * connecting to an AP (i.e. country ie).
+	 */
+	if (request->initiator == NL80211_REGDOM_SET_BY_USER &&
+	    !rtw89_regd_is_ww(rtwdev->regd))
+		wiphy->regulatory_flags |= REGULATORY_COUNTRY_IE_IGNORE;
+	else
+		wiphy->regulatory_flags &= ~REGULATORY_COUNTRY_IE_IGNORE;
+}
+
+void rtw89_regd_notifier(struct wiphy *wiphy, struct regulatory_request *request)
+{
+	struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
+	struct rtw89_dev *rtwdev = hw->priv;
+
+	mutex_lock(&rtwdev->mutex);
+	rtw89_leave_ps_mode(rtwdev);
+
+	if (wiphy->regd) {
+		rtw89_debug(rtwdev, RTW89_DBG_REGD,
+			    "There is a country domain programmed in chip, ignore notifications\n");
+		goto exit;
+	}
+	rtw89_regd_notifier_apply(rtwdev, wiphy, request);
+	rtw89_debug(rtwdev, RTW89_DBG_REGD,
+		    "get alpha2 %c%c from initiator %d, mapping to 2g txregd %d, 5g txregd %d\n",
+		    request->alpha2[0], request->alpha2[1], request->initiator,
+		    rtwdev->regd->txpwr_regd[RTW89_BAND_2G],
+		    rtwdev->regd->txpwr_regd[RTW89_BAND_5G]);
+
+	rtw89_chip_set_txpwr(rtwdev);
+
+exit:
+	mutex_unlock(&rtwdev->mutex);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a.c
@@ -0,0 +1,2036 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "coex.h"
+#include "mac.h"
+#include "phy.h"
+#include "reg.h"
+#include "rtw8852a.h"
+#include "rtw8852a_rfk.h"
+#include "rtw8852a_table.h"
+#include "txrx.h"
+
+static const struct rtw89_hfc_ch_cfg rtw8852a_hfc_chcfg_pcie[] = {
+	{128, 1896, grp_0}, /* ACH 0 */
+	{128, 1896, grp_0}, /* ACH 1 */
+	{128, 1896, grp_0}, /* ACH 2 */
+	{128, 1896, grp_0}, /* ACH 3 */
+	{128, 1896, grp_1}, /* ACH 4 */
+	{128, 1896, grp_1}, /* ACH 5 */
+	{128, 1896, grp_1}, /* ACH 6 */
+	{128, 1896, grp_1}, /* ACH 7 */
+	{32, 1896, grp_0}, /* B0MGQ */
+	{128, 1896, grp_0}, /* B0HIQ */
+	{32, 1896, grp_1}, /* B1MGQ */
+	{128, 1896, grp_1}, /* B1HIQ */
+	{40, 0, 0} /* FWCMDQ */
+};
+
+static const struct rtw89_hfc_pub_cfg rtw8852a_hfc_pubcfg_pcie = {
+	1896, /* Group 0 */
+	1896, /* Group 1 */
+	3792, /* Public Max */
+	0 /* WP threshold */
+};
+
+static const struct rtw89_hfc_param_ini rtw8852a_hfc_param_ini_pcie[] = {
+	[RTW89_QTA_SCC] = {rtw8852a_hfc_chcfg_pcie, &rtw8852a_hfc_pubcfg_pcie,
+			   &rtw_hfc_preccfg_pcie, RTW89_HCIFC_POH},
+	[RTW89_QTA_DLFW] = {NULL, NULL, &rtw_hfc_preccfg_pcie, RTW89_HCIFC_POH},
+	[RTW89_QTA_INVALID] = {NULL},
+};
+
+static const struct rtw89_dle_mem rtw8852a_dle_mem_pcie[] = {
+	[RTW89_QTA_SCC] = {RTW89_QTA_SCC, &wde_size0, &ple_size0, &wde_qt0,
+			    &wde_qt0, &ple_qt4, &ple_qt5},
+	[RTW89_QTA_DLFW] = {RTW89_QTA_DLFW, &wde_size4, &ple_size4,
+			    &wde_qt4, &wde_qt4, &ple_qt13, &ple_qt13},
+	[RTW89_QTA_INVALID] = {RTW89_QTA_INVALID, NULL, NULL, NULL, NULL, NULL,
+			       NULL},
+};
+
+static const struct rtw89_reg2_def  rtw8852a_pmac_ht20_mcs7_tbl[] = {
+	{0x44AC, 0x00000000},
+	{0x44B0, 0x00000000},
+	{0x44B4, 0x00000000},
+	{0x44B8, 0x00000000},
+	{0x44BC, 0x00000000},
+	{0x44C0, 0x00000000},
+	{0x44C4, 0x00000000},
+	{0x44C8, 0x00000000},
+	{0x44CC, 0x00000000},
+	{0x44D0, 0x00000000},
+	{0x44D4, 0x00000000},
+	{0x44D8, 0x00000000},
+	{0x44DC, 0x00000000},
+	{0x44E0, 0x00000000},
+	{0x44E4, 0x00000000},
+	{0x44E8, 0x00000000},
+	{0x44EC, 0x00000000},
+	{0x44F0, 0x00000000},
+	{0x44F4, 0x00000000},
+	{0x44F8, 0x00000000},
+	{0x44FC, 0x00000000},
+	{0x4500, 0x00000000},
+	{0x4504, 0x00000000},
+	{0x4508, 0x00000000},
+	{0x450C, 0x00000000},
+	{0x4510, 0x00000000},
+	{0x4514, 0x00000000},
+	{0x4518, 0x00000000},
+	{0x451C, 0x00000000},
+	{0x4520, 0x00000000},
+	{0x4524, 0x00000000},
+	{0x4528, 0x00000000},
+	{0x452C, 0x00000000},
+	{0x4530, 0x4E1F3E81},
+	{0x4534, 0x00000000},
+	{0x4538, 0x0000005A},
+	{0x453C, 0x00000000},
+	{0x4540, 0x00000000},
+	{0x4544, 0x00000000},
+	{0x4548, 0x00000000},
+	{0x454C, 0x00000000},
+	{0x4550, 0x00000000},
+	{0x4554, 0x00000000},
+	{0x4558, 0x00000000},
+	{0x455C, 0x00000000},
+	{0x4560, 0x4060001A},
+	{0x4564, 0x40000000},
+	{0x4568, 0x00000000},
+	{0x456C, 0x00000000},
+	{0x4570, 0x04000007},
+	{0x4574, 0x0000DC87},
+	{0x4578, 0x00000BAB},
+	{0x457C, 0x03E00000},
+	{0x4580, 0x00000048},
+	{0x4584, 0x00000000},
+	{0x4588, 0x000003E8},
+	{0x458C, 0x30000000},
+	{0x4590, 0x00000000},
+	{0x4594, 0x10000000},
+	{0x4598, 0x00000001},
+	{0x459C, 0x00030000},
+	{0x45A0, 0x01000000},
+	{0x45A4, 0x03000200},
+	{0x45A8, 0xC00001C0},
+	{0x45AC, 0x78018000},
+	{0x45B0, 0x80000000},
+	{0x45B4, 0x01C80600},
+	{0x45B8, 0x00000002},
+	{0x4594, 0x10000000}
+};
+
+static const struct rtw89_reg3_def rtw8852a_btc_preagc_en_defs[] = {
+	{0x4624, GENMASK(20, 14), 0x40},
+	{0x46f8, GENMASK(20, 14), 0x40},
+	{0x4674, GENMASK(20, 19), 0x2},
+	{0x4748, GENMASK(20, 19), 0x2},
+	{0x4650, GENMASK(14, 10), 0x18},
+	{0x4724, GENMASK(14, 10), 0x18},
+	{0x4688, GENMASK(1, 0), 0x3},
+	{0x475c, GENMASK(1, 0), 0x3},
+};
+
+static DECLARE_PHY_REG3_TBL(rtw8852a_btc_preagc_en_defs);
+
+static const struct rtw89_reg3_def rtw8852a_btc_preagc_dis_defs[] = {
+	{0x4624, GENMASK(20, 14), 0x1a},
+	{0x46f8, GENMASK(20, 14), 0x1a},
+	{0x4674, GENMASK(20, 19), 0x1},
+	{0x4748, GENMASK(20, 19), 0x1},
+	{0x4650, GENMASK(14, 10), 0x12},
+	{0x4724, GENMASK(14, 10), 0x12},
+	{0x4688, GENMASK(1, 0), 0x0},
+	{0x475c, GENMASK(1, 0), 0x0},
+};
+
+static DECLARE_PHY_REG3_TBL(rtw8852a_btc_preagc_dis_defs);
+
+static const struct rtw89_pwr_cfg rtw8852a_pwron[] = {
+	{0x00C6,
+	 PWR_CV_MSK_B,
+	 PWR_INTF_MSK_PCIE,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(6), BIT(6)},
+	{0x1086,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_SDIO,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), 0},
+	{0x1086,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_SDIO,
+	 PWR_BASE_MAC,
+	 PWR_CMD_POLL, BIT(1), BIT(1)},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(4) | BIT(3), 0},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(7), 0},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(2), 0},
+	{0x0006,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_POLL, BIT(1), BIT(1)},
+	{0x0006,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_POLL, BIT(0), 0},
+	{0x106D,
+	 PWR_CV_MSK_B | PWR_CV_MSK_C,
+	 PWR_INTF_MSK_USB,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(6), 0},
+	{0x0088,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x0088,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), 0},
+	{0x0088,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x0088,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), 0},
+	{0x0088,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x0083,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(6), 0},
+	{0x0080,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(5), BIT(5)},
+	{0x0024,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(4) | BIT(3) | BIT(2) | BIT(1) | BIT(0), 0},
+	{0x02A0,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(1), BIT(1)},
+	{0x02A2,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(7) | BIT(6) | BIT(5), 0},
+	{0x0071,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_PCIE,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(4), 0},
+	{0x0010,
+	 PWR_CV_MSK_A,
+	 PWR_INTF_MSK_PCIE,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(2), BIT(2)},
+	{0x02A0,
+	 PWR_CV_MSK_A,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(7) | BIT(6), 0},
+	{0xFFFF,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 0,
+	 PWR_CMD_END, 0, 0},
+};
+
+static const struct rtw89_pwr_cfg rtw8852a_pwroff[] = {
+	{0x02F0,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, 0xFF, 0},
+	{0x02F1,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, 0xFF, 0},
+	{0x0006,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x0002,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(1) | BIT(0), 0},
+	{0x0082,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(1) | BIT(0), 0},
+	{0x106D,
+	 PWR_CV_MSK_B | PWR_CV_MSK_C,
+	 PWR_INTF_MSK_USB,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(6), BIT(6)},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(1), BIT(1)},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 PWR_BASE_MAC,
+	 PWR_CMD_POLL, BIT(1), 0},
+	{0x0091,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_PCIE,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), 0},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_PCIE,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(2), BIT(2)},
+	{0x0007,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_USB,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(4), 0},
+	{0x0007,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_SDIO,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(6) | BIT(4), 0},
+	{0x0005,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_SDIO,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(4) | BIT(3), BIT(3)},
+	{0x0005,
+	 PWR_CV_MSK_C | PWR_CV_MSK_D | PWR_CV_MSK_E | PWR_CV_MSK_F |
+	 PWR_CV_MSK_G,
+	 PWR_INTF_MSK_USB,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(4) | BIT(3), BIT(3)},
+	{0x1086,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_SDIO,
+	 PWR_BASE_MAC,
+	 PWR_CMD_WRITE, BIT(0), BIT(0)},
+	{0x1086,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_SDIO,
+	 PWR_BASE_MAC,
+	 PWR_CMD_POLL, BIT(1), 0},
+	{0xFFFF,
+	 PWR_CV_MSK_ALL,
+	 PWR_INTF_MSK_ALL,
+	 0,
+	 PWR_CMD_END, 0, 0},
+};
+
+static const struct rtw89_pwr_cfg * const pwr_on_seq_8852a[] = {
+	rtw8852a_pwron, NULL
+};
+
+static const struct rtw89_pwr_cfg * const pwr_off_seq_8852a[] = {
+	rtw8852a_pwroff, NULL
+};
+
+static void rtw8852ae_efuse_parsing(struct rtw89_efuse *efuse,
+				    struct rtw8852a_efuse *map)
+{
+	ether_addr_copy(efuse->addr, map->e.mac_addr);
+	efuse->rfe_type = map->rfe_type;
+	efuse->xtal_cap = map->xtal_k;
+}
+
+static void rtw8852a_efuse_parsing_tssi(struct rtw89_dev *rtwdev,
+					struct rtw8852a_efuse *map)
+{
+	struct rtw89_tssi_info *tssi = &rtwdev->tssi;
+	struct rtw8852a_tssi_offset *ofst[] = {&map->path_a_tssi, &map->path_b_tssi};
+	u8 i, j;
+
+	tssi->thermal[RF_PATH_A] = map->path_a_therm;
+	tssi->thermal[RF_PATH_B] = map->path_b_therm;
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		memcpy(tssi->tssi_cck[i], ofst[i]->cck_tssi,
+		       sizeof(ofst[i]->cck_tssi));
+
+		for (j = 0; j < TSSI_CCK_CH_GROUP_NUM; j++)
+			rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+				    "[TSSI][EFUSE] path=%d cck[%d]=0x%x\n",
+				    i, j, tssi->tssi_cck[i][j]);
+
+		memcpy(tssi->tssi_mcs[i], ofst[i]->bw40_tssi,
+		       sizeof(ofst[i]->bw40_tssi));
+		memcpy(tssi->tssi_mcs[i] + TSSI_MCS_2G_CH_GROUP_NUM,
+		       ofst[i]->bw40_1s_tssi_5g, sizeof(ofst[i]->bw40_1s_tssi_5g));
+
+		for (j = 0; j < TSSI_MCS_CH_GROUP_NUM; j++)
+			rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+				    "[TSSI][EFUSE] path=%d mcs[%d]=0x%x\n",
+				    i, j, tssi->tssi_mcs[i][j]);
+	}
+}
+
+static int rtw8852a_read_efuse(struct rtw89_dev *rtwdev, u8 *log_map)
+{
+	struct rtw89_efuse *efuse = &rtwdev->efuse;
+	struct rtw8852a_efuse *map;
+
+	map = (struct rtw8852a_efuse *)log_map;
+
+	efuse->country_code[0] = map->country_code[0];
+	efuse->country_code[1] = map->country_code[1];
+	rtw8852a_efuse_parsing_tssi(rtwdev, map);
+
+	switch (rtwdev->hci.type) {
+	case RTW89_HCI_TYPE_PCIE:
+		rtw8852ae_efuse_parsing(efuse, map);
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	rtw89_info(rtwdev, "chip rfe_type is %d\n", efuse->rfe_type);
+
+	return 0;
+}
+
+static void rtw8852a_phycap_parsing_tssi(struct rtw89_dev *rtwdev, u8 *phycap_map)
+{
+	struct rtw89_tssi_info *tssi = &rtwdev->tssi;
+	static const u32 tssi_trim_addr[RF_PATH_NUM_8852A] = {0x5D6, 0x5AB};
+	u32 addr = rtwdev->chip->phycap_addr;
+	bool pg = false;
+	u32 ofst;
+	u8 i, j;
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		for (j = 0; j < TSSI_TRIM_CH_GROUP_NUM; j++) {
+			/* addrs are in decreasing order */
+			ofst = tssi_trim_addr[i] - addr - j;
+			tssi->tssi_trim[i][j] = phycap_map[ofst];
+
+			if (phycap_map[ofst] != 0xff)
+				pg = true;
+		}
+	}
+
+	if (!pg) {
+		memset(tssi->tssi_trim, 0, sizeof(tssi->tssi_trim));
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM] no PG, set all trim info to 0\n");
+	}
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++)
+		for (j = 0; j < TSSI_TRIM_CH_GROUP_NUM; j++)
+			rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+				    "[TSSI] path=%d idx=%d trim=0x%x addr=0x%x\n",
+				    i, j, tssi->tssi_trim[i][j],
+				    tssi_trim_addr[i] - j);
+}
+
+static void rtw8852a_phycap_parsing_thermal_trim(struct rtw89_dev *rtwdev,
+						 u8 *phycap_map)
+{
+	struct rtw89_power_trim_info *info = &rtwdev->pwr_trim;
+	static const u32 thm_trim_addr[RF_PATH_NUM_8852A] = {0x5DF, 0x5DC};
+	u32 addr = rtwdev->chip->phycap_addr;
+	u8 i;
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		info->thermal_trim[i] = phycap_map[thm_trim_addr[i] - addr];
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[THERMAL][TRIM] path=%d thermal_trim=0x%x\n",
+			    i, info->thermal_trim[i]);
+
+		if (info->thermal_trim[i] != 0xff)
+			info->pg_thermal_trim = true;
+	}
+}
+
+static void rtw8852a_thermal_trim(struct rtw89_dev *rtwdev)
+{
+#define __thm_setting(raw)				\
+({							\
+	u8 __v = (raw);					\
+	((__v & 0x1) << 3) | ((__v & 0x1f) >> 1);	\
+})
+	struct rtw89_power_trim_info *info = &rtwdev->pwr_trim;
+	u8 i, val;
+
+	if (!info->pg_thermal_trim) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[THERMAL][TRIM] no PG, do nothing\n");
+
+		return;
+	}
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		val = __thm_setting(info->thermal_trim[i]);
+		rtw89_write_rf(rtwdev, i, RR_TM2, RR_TM2_OFF, val);
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[THERMAL][TRIM] path=%d thermal_setting=0x%x\n",
+			    i, val);
+	}
+#undef __thm_setting
+}
+
+static void rtw8852a_phycap_parsing_pa_bias_trim(struct rtw89_dev *rtwdev,
+						 u8 *phycap_map)
+{
+	struct rtw89_power_trim_info *info = &rtwdev->pwr_trim;
+	static const u32 pabias_trim_addr[RF_PATH_NUM_8852A] = {0x5DE, 0x5DB};
+	u32 addr = rtwdev->chip->phycap_addr;
+	u8 i;
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		info->pa_bias_trim[i] = phycap_map[pabias_trim_addr[i] - addr];
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[PA_BIAS][TRIM] path=%d pa_bias_trim=0x%x\n",
+			    i, info->pa_bias_trim[i]);
+
+		if (info->pa_bias_trim[i] != 0xff)
+			info->pg_pa_bias_trim = true;
+	}
+}
+
+static void rtw8852a_pa_bias_trim(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_power_trim_info *info = &rtwdev->pwr_trim;
+	u8 pabias_2g, pabias_5g;
+	u8 i;
+
+	if (!info->pg_pa_bias_trim) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[PA_BIAS][TRIM] no PG, do nothing\n");
+
+		return;
+	}
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		pabias_2g = FIELD_GET(GENMASK(3, 0), info->pa_bias_trim[i]);
+		pabias_5g = FIELD_GET(GENMASK(7, 4), info->pa_bias_trim[i]);
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[PA_BIAS][TRIM] path=%d 2G=0x%x 5G=0x%x\n",
+			    i, pabias_2g, pabias_5g);
+
+		rtw89_write_rf(rtwdev, i, RR_BIASA, RR_BIASA_TXG, pabias_2g);
+		rtw89_write_rf(rtwdev, i, RR_BIASA, RR_BIASA_TXA, pabias_5g);
+	}
+}
+
+static int rtw8852a_read_phycap(struct rtw89_dev *rtwdev, u8 *phycap_map)
+{
+	rtw8852a_phycap_parsing_tssi(rtwdev, phycap_map);
+	rtw8852a_phycap_parsing_thermal_trim(rtwdev, phycap_map);
+	rtw8852a_phycap_parsing_pa_bias_trim(rtwdev, phycap_map);
+
+	return 0;
+}
+
+static void rtw8852a_power_trim(struct rtw89_dev *rtwdev)
+{
+	rtw8852a_thermal_trim(rtwdev);
+	rtw8852a_pa_bias_trim(rtwdev);
+}
+
+static void rtw8852a_set_channel_mac(struct rtw89_dev *rtwdev,
+				     struct rtw89_channel_params *param,
+				     u8 mac_idx)
+{
+	u32 rf_mod = rtw89_mac_reg_by_idx(R_AX_WMAC_RFMOD, mac_idx);
+	u32 sub_carr = rtw89_mac_reg_by_idx(R_AX_TX_SUB_CARRIER_VALUE,
+					     mac_idx);
+	u32 chk_rate = rtw89_mac_reg_by_idx(R_AX_TXRATE_CHK, mac_idx);
+	u8 txsc20 = 0, txsc40 = 0;
+
+	switch (param->bandwidth) {
+	case RTW89_CHANNEL_WIDTH_80:
+		txsc40 = rtw89_phy_get_txsc(rtwdev, param,
+					    RTW89_CHANNEL_WIDTH_40);
+		fallthrough;
+	case RTW89_CHANNEL_WIDTH_40:
+		txsc20 = rtw89_phy_get_txsc(rtwdev, param,
+					    RTW89_CHANNEL_WIDTH_20);
+		break;
+	default:
+		break;
+	}
+
+	switch (param->bandwidth) {
+	case RTW89_CHANNEL_WIDTH_80:
+		rtw89_write8_mask(rtwdev, rf_mod, B_AX_WMAC_RFMOD_MASK, BIT(1));
+		rtw89_write32(rtwdev, sub_carr, txsc20 | (txsc40 << 4));
+		break;
+	case RTW89_CHANNEL_WIDTH_40:
+		rtw89_write8_mask(rtwdev, rf_mod, B_AX_WMAC_RFMOD_MASK, BIT(0));
+		rtw89_write32(rtwdev, sub_carr, txsc20);
+		break;
+	case RTW89_CHANNEL_WIDTH_20:
+		rtw89_write8_clr(rtwdev, rf_mod, B_AX_WMAC_RFMOD_MASK);
+		rtw89_write32(rtwdev, sub_carr, 0);
+		break;
+	default:
+		break;
+	}
+
+	if (param->center_chan > 14)
+		rtw89_write8_set(rtwdev, chk_rate,
+				 B_AX_CHECK_CCK_EN | B_AX_RTS_LIMIT_IN_OFDM6);
+	else
+		rtw89_write8_clr(rtwdev, chk_rate,
+				 B_AX_CHECK_CCK_EN | B_AX_RTS_LIMIT_IN_OFDM6);
+}
+
+static const u32 rtw8852a_sco_barker_threshold[14] = {
+	0x1cfea, 0x1d0e1, 0x1d1d7, 0x1d2cd, 0x1d3c3, 0x1d4b9, 0x1d5b0, 0x1d6a6,
+	0x1d79c, 0x1d892, 0x1d988, 0x1da7f, 0x1db75, 0x1ddc4
+};
+
+static const u32 rtw8852a_sco_cck_threshold[14] = {
+	0x27de3, 0x27f35, 0x28088, 0x281da, 0x2832d, 0x2847f, 0x285d2, 0x28724,
+	0x28877, 0x289c9, 0x28b1c, 0x28c6e, 0x28dc1, 0x290ed
+};
+
+static int rtw8852a_ctrl_sco_cck(struct rtw89_dev *rtwdev, u8 central_ch,
+				 u8 primary_ch, enum rtw89_bandwidth bw)
+{
+	u8 ch_element;
+
+	if (bw == RTW89_CHANNEL_WIDTH_20) {
+		ch_element = central_ch - 1;
+	} else if (bw == RTW89_CHANNEL_WIDTH_40) {
+		if (primary_ch == 1)
+			ch_element = central_ch - 1 + 2;
+		else
+			ch_element = central_ch - 1 - 2;
+	} else {
+		rtw89_warn(rtwdev, "Invalid BW:%d for CCK\n", bw);
+		return -EINVAL;
+	}
+	rtw89_phy_write32_mask(rtwdev, R_RXSCOBC, B_RXSCOBC_TH,
+			       rtw8852a_sco_barker_threshold[ch_element]);
+	rtw89_phy_write32_mask(rtwdev, R_RXSCOCCK, B_RXSCOCCK_TH,
+			       rtw8852a_sco_cck_threshold[ch_element]);
+
+	return 0;
+}
+
+static void rtw8852a_ch_setting(struct rtw89_dev *rtwdev, u8 central_ch,
+				u8 path)
+{
+	u32 val;
+
+	val = rtw89_read_rf(rtwdev, path, RR_CFGCH, RFREG_MASK);
+	if (val == INV_RF_DATA) {
+		rtw89_warn(rtwdev, "Invalid RF_0x18 for Path-%d\n", path);
+		return;
+	}
+	val &= ~0x303ff;
+	val |= central_ch;
+	if (central_ch > 14)
+		val |= (BIT(16) | BIT(8));
+	rtw89_write_rf(rtwdev, path, RR_CFGCH, RFREG_MASK, val);
+}
+
+static u8 rtw8852a_sco_mapping(u8 central_ch)
+{
+	if (central_ch == 1)
+		return 109;
+	else if (central_ch >= 2 && central_ch <= 6)
+		return 108;
+	else if (central_ch >= 7 && central_ch <= 10)
+		return 107;
+	else if (central_ch >= 11 && central_ch <= 14)
+		return 106;
+	else if (central_ch == 36 || central_ch == 38)
+		return 51;
+	else if (central_ch >= 40 && central_ch <= 58)
+		return 50;
+	else if (central_ch >= 60 && central_ch <= 64)
+		return 49;
+	else if (central_ch == 100 || central_ch == 102)
+		return 48;
+	else if (central_ch >= 104 && central_ch <= 126)
+		return 47;
+	else if (central_ch >= 128 && central_ch <= 151)
+		return 46;
+	else if (central_ch >= 153 && central_ch <= 177)
+		return 45;
+	else
+		return 0;
+}
+
+static void rtw8852a_ctrl_ch(struct rtw89_dev *rtwdev, u8 central_ch,
+			     enum rtw89_phy_idx phy_idx)
+{
+	u8 sco_comp;
+	bool is_2g = central_ch <= 14;
+
+	if (phy_idx == RTW89_PHY_0) {
+		/* Path A */
+		rtw8852a_ch_setting(rtwdev, central_ch, RF_PATH_A);
+		if (is_2g)
+			rtw89_phy_write32_idx(rtwdev, R_PATH0_TIA_ERR_G1,
+					      B_PATH0_TIA_ERR_G1_SEL, 1,
+					      phy_idx);
+		else
+			rtw89_phy_write32_idx(rtwdev, R_PATH0_TIA_ERR_G1,
+					      B_PATH0_TIA_ERR_G1_SEL, 0,
+					      phy_idx);
+
+		/* Path B */
+		if (!rtwdev->dbcc_en) {
+			rtw8852a_ch_setting(rtwdev, central_ch, RF_PATH_B);
+			if (is_2g)
+				rtw89_phy_write32_idx(rtwdev, R_P1_MODE,
+						      B_P1_MODE_SEL,
+						      1, phy_idx);
+			else
+				rtw89_phy_write32_idx(rtwdev, R_P1_MODE,
+						      B_P1_MODE_SEL,
+						      0, phy_idx);
+		} else {
+			if (is_2g)
+				rtw89_phy_write32_clr(rtwdev, R_2P4G_BAND,
+						      B_2P4G_BAND_SEL);
+			else
+				rtw89_phy_write32_set(rtwdev, R_2P4G_BAND,
+						      B_2P4G_BAND_SEL);
+		}
+		/* SCO compensate FC setting */
+		sco_comp = rtw8852a_sco_mapping(central_ch);
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_INV,
+				      sco_comp, phy_idx);
+	} else {
+		/* Path B */
+		rtw8852a_ch_setting(rtwdev, central_ch, RF_PATH_B);
+		if (is_2g)
+			rtw89_phy_write32_idx(rtwdev, R_P1_MODE,
+					      B_P1_MODE_SEL,
+					      1, phy_idx);
+		else
+			rtw89_phy_write32_idx(rtwdev, R_P1_MODE,
+					      B_P1_MODE_SEL,
+					      1, phy_idx);
+		/* SCO compensate FC setting */
+		sco_comp = rtw8852a_sco_mapping(central_ch);
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_INV,
+				      sco_comp, phy_idx);
+	}
+
+	/* Band edge */
+	if (is_2g)
+		rtw89_phy_write32_idx(rtwdev, R_BANDEDGE, B_BANDEDGE_EN, 1,
+				      phy_idx);
+	else
+		rtw89_phy_write32_idx(rtwdev, R_BANDEDGE, B_BANDEDGE_EN, 0,
+				      phy_idx);
+
+	/* CCK parameters */
+	if (central_ch == 14) {
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR0, B_TXFIR_C01,
+				       0x3b13ff);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR2, B_TXFIR_C23,
+				       0x1c42de);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR4, B_TXFIR_C45,
+				       0xfdb0ad);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR6, B_TXFIR_C67,
+				       0xf60f6e);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR8, B_TXFIR_C89,
+				       0xfd8f92);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIRA, B_TXFIR_CAB, 0x2d011);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIRC, B_TXFIR_CCD, 0x1c02c);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIRE, B_TXFIR_CEF,
+				       0xfff00a);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR0, B_TXFIR_C01,
+				       0x3d23ff);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR2, B_TXFIR_C23,
+				       0x29b354);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR4, B_TXFIR_C45, 0xfc1c8);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR6, B_TXFIR_C67,
+				       0xfdb053);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIR8, B_TXFIR_C89,
+				       0xf86f9a);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIRA, B_TXFIR_CAB,
+				       0xfaef92);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIRC, B_TXFIR_CCD,
+				       0xfe5fcc);
+		rtw89_phy_write32_mask(rtwdev, R_TXFIRE, B_TXFIR_CEF,
+				       0xffdff5);
+	}
+}
+
+static void rtw8852a_bw_setting(struct rtw89_dev *rtwdev, u8 bw, u8 path)
+{
+	u32 val = 0;
+	u32 adc_sel[2] = {0x12d0, 0x32d0};
+	u32 wbadc_sel[2] = {0x12ec, 0x32ec};
+
+	val = rtw89_read_rf(rtwdev, path, RR_CFGCH, RFREG_MASK);
+	if (val == INV_RF_DATA) {
+		rtw89_warn(rtwdev, "Invalid RF_0x18 for Path-%d\n", path);
+		return;
+	}
+	val &= ~(BIT(11) | BIT(10));
+	switch (bw) {
+	case RTW89_CHANNEL_WIDTH_5:
+		rtw89_phy_write32_mask(rtwdev, adc_sel[path], 0x6000, 0x1);
+		rtw89_phy_write32_mask(rtwdev, wbadc_sel[path], 0x30, 0x0);
+		val |= (BIT(11) | BIT(10));
+		break;
+	case RTW89_CHANNEL_WIDTH_10:
+		rtw89_phy_write32_mask(rtwdev, adc_sel[path], 0x6000, 0x2);
+		rtw89_phy_write32_mask(rtwdev, wbadc_sel[path], 0x30, 0x1);
+		val |= (BIT(11) | BIT(10));
+		break;
+	case RTW89_CHANNEL_WIDTH_20:
+		rtw89_phy_write32_mask(rtwdev, adc_sel[path], 0x6000, 0x0);
+		rtw89_phy_write32_mask(rtwdev, wbadc_sel[path], 0x30, 0x2);
+		val |= (BIT(11) | BIT(10));
+		break;
+	case RTW89_CHANNEL_WIDTH_40:
+		rtw89_phy_write32_mask(rtwdev, adc_sel[path], 0x6000, 0x0);
+		rtw89_phy_write32_mask(rtwdev, wbadc_sel[path], 0x30, 0x2);
+		val |= BIT(11);
+		break;
+	case RTW89_CHANNEL_WIDTH_80:
+		rtw89_phy_write32_mask(rtwdev, adc_sel[path], 0x6000, 0x0);
+		rtw89_phy_write32_mask(rtwdev, wbadc_sel[path], 0x30, 0x2);
+		val |= BIT(10);
+		break;
+	default:
+		rtw89_warn(rtwdev, "Fail to set ADC\n");
+	}
+
+	rtw89_write_rf(rtwdev, path, RR_CFGCH, RFREG_MASK, val);
+}
+
+static void
+rtw8852a_ctrl_bw(struct rtw89_dev *rtwdev, u8 pri_ch, u8 bw,
+		 enum rtw89_phy_idx phy_idx)
+{
+	/* Switch bandwidth */
+	switch (bw) {
+	case RTW89_CHANNEL_WIDTH_5:
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_SET, 0x0,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_SBW, 0x1,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_PRICH,
+				      0x0, phy_idx);
+		break;
+	case RTW89_CHANNEL_WIDTH_10:
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_SET, 0x0,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_SBW, 0x2,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_PRICH,
+				      0x0, phy_idx);
+		break;
+	case RTW89_CHANNEL_WIDTH_20:
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_SET, 0x0,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_SBW, 0x0,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_PRICH,
+				      0x0, phy_idx);
+		break;
+	case RTW89_CHANNEL_WIDTH_40:
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_SET, 0x1,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_SBW, 0x0,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_PRICH,
+				      pri_ch,
+				      phy_idx);
+		if (pri_ch == RTW89_SC_20_UPPER)
+			rtw89_phy_write32_mask(rtwdev, R_RXSC, B_RXSC_EN, 1);
+		else
+			rtw89_phy_write32_mask(rtwdev, R_RXSC, B_RXSC_EN, 0);
+		break;
+	case RTW89_CHANNEL_WIDTH_80:
+		rtw89_phy_write32_idx(rtwdev, R_FC0_BW, B_FC0_BW_SET, 0x2,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_SBW, 0x0,
+				      phy_idx);
+		rtw89_phy_write32_idx(rtwdev, R_CHBW_MOD, B_CHBW_MOD_PRICH,
+				      pri_ch,
+				      phy_idx);
+		break;
+	default:
+		rtw89_warn(rtwdev, "Fail to switch bw (bw:%d, pri ch:%d)\n", bw,
+			   pri_ch);
+	}
+
+	if (phy_idx == RTW89_PHY_0) {
+		rtw8852a_bw_setting(rtwdev, bw, RF_PATH_A);
+		if (!rtwdev->dbcc_en)
+			rtw8852a_bw_setting(rtwdev, bw, RF_PATH_B);
+	} else {
+		rtw8852a_bw_setting(rtwdev, bw, RF_PATH_B);
+	}
+}
+
+static void rtw8852a_spur_elimination(struct rtw89_dev *rtwdev, u8 central_ch)
+{
+	if (central_ch == 153) {
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX, B_P0_NBIIDX_VAL,
+				       0x210);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX, B_P1_NBIIDX_VAL,
+				       0x210);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI, 0xfff, 0x7c0);
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX,
+				       B_P0_NBIIDX_NOTCH_EN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX,
+				       B_P1_NBIIDX_NOTCH_EN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI_EN, B_SEG0CSI_EN,
+				       0x1);
+	} else if (central_ch == 151) {
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX, B_P0_NBIIDX_VAL,
+				       0x210);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX, B_P1_NBIIDX_VAL,
+				       0x210);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI, 0xfff, 0x40);
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX,
+				       B_P0_NBIIDX_NOTCH_EN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX,
+				       B_P1_NBIIDX_NOTCH_EN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI_EN, B_SEG0CSI_EN,
+				       0x1);
+	} else if (central_ch == 155) {
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX, B_P0_NBIIDX_VAL,
+				       0x2d0);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX, B_P1_NBIIDX_VAL,
+				       0x2d0);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI, 0xfff, 0x740);
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX,
+				       B_P0_NBIIDX_NOTCH_EN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX,
+				       B_P1_NBIIDX_NOTCH_EN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI_EN, B_SEG0CSI_EN,
+				       0x1);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_P0_NBIIDX,
+				       B_P0_NBIIDX_NOTCH_EN, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_P1_NBIIDX,
+				       B_P1_NBIIDX_NOTCH_EN, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_SEG0CSI_EN, B_SEG0CSI_EN,
+				       0x0);
+	}
+}
+
+static void rtw8852a_bb_reset_all(struct rtw89_dev *rtwdev,
+				  enum rtw89_phy_idx phy_idx)
+{
+	rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL, 1,
+			      phy_idx);
+	rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL, 0,
+			      phy_idx);
+	rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL, 1,
+			      phy_idx);
+}
+
+static void rtw8852a_bb_reset_en(struct rtw89_dev *rtwdev,
+				 enum rtw89_phy_idx phy_idx, bool en)
+{
+	if (en)
+		rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL,
+				      1,
+				      phy_idx);
+	else
+		rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL,
+				      0,
+				      phy_idx);
+}
+
+static void rtw8852a_bb_reset(struct rtw89_dev *rtwdev,
+			      enum rtw89_phy_idx phy_idx)
+{
+	rtw89_phy_write32_set(rtwdev, R_P0_TXPW_RSTB, B_P0_TXPW_RSTB_MANON);
+	rtw89_phy_write32_set(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_TRK_EN);
+	rtw89_phy_write32_set(rtwdev, R_P1_TXPW_RSTB, B_P1_TXPW_RSTB_MANON);
+	rtw89_phy_write32_set(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_TRK_EN);
+	rtw8852a_bb_reset_all(rtwdev, phy_idx);
+	rtw89_phy_write32_clr(rtwdev, R_P0_TXPW_RSTB, B_P0_TXPW_RSTB_MANON);
+	rtw89_phy_write32_clr(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_TRK_EN);
+	rtw89_phy_write32_clr(rtwdev, R_P1_TXPW_RSTB, B_P1_TXPW_RSTB_MANON);
+	rtw89_phy_write32_clr(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_TRK_EN);
+}
+
+static void rtw8852a_bb_macid_ctrl_init(struct rtw89_dev *rtwdev,
+					enum rtw89_phy_idx phy_idx)
+{
+	u32 addr;
+
+	for (addr = R_AX_PWR_MACID_LMT_TABLE0;
+	     addr <= R_AX_PWR_MACID_LMT_TABLE127; addr += 4)
+		rtw89_mac_txpwr_write32(rtwdev, phy_idx, addr, 0);
+}
+
+static void rtw8852a_bb_sethw(struct rtw89_dev *rtwdev)
+{
+	rtw89_phy_write32_clr(rtwdev, R_P0_EN_SOUND_WO_NDP, B_P0_EN_SOUND_WO_NDP);
+	rtw89_phy_write32_clr(rtwdev, R_P1_EN_SOUND_WO_NDP, B_P1_EN_SOUND_WO_NDP);
+
+	if (rtwdev->hal.cv <= CHIP_CCV) {
+		rtw89_phy_write32_set(rtwdev, R_RSTB_WATCH_DOG, B_P0_RSTB_WATCH_DOG);
+		rtw89_phy_write32(rtwdev, R_BRK_ASYNC_RST_EN_1, 0x864FA000);
+		rtw89_phy_write32(rtwdev, R_BRK_ASYNC_RST_EN_2, 0x3F);
+		rtw89_phy_write32(rtwdev, R_BRK_ASYNC_RST_EN_3, 0x7FFF);
+		rtw89_phy_write32_set(rtwdev, R_SPOOF_ASYNC_RST, B_SPOOF_ASYNC_RST);
+		rtw89_phy_write32_set(rtwdev, R_P0_TXPW_RSTB, B_P0_TXPW_RSTB_MANON);
+		rtw89_phy_write32_set(rtwdev, R_P1_TXPW_RSTB, B_P1_TXPW_RSTB_MANON);
+	}
+	rtw89_phy_write32_mask(rtwdev, R_CFO_TRK0, B_CFO_TRK_MSK, 0x1f);
+	rtw89_phy_write32_mask(rtwdev, R_CFO_TRK1, B_CFO_TRK_MSK, 0x0c);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_MOD, 0x0, RTW89_PHY_0);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_MOD, 0x0, RTW89_PHY_1);
+	rtw89_phy_write32_clr(rtwdev, R_NDP_BRK0, B_NDP_RU_BRK);
+	rtw89_phy_write32_set(rtwdev, R_NDP_BRK1, B_NDP_RU_BRK);
+
+	rtw8852a_bb_macid_ctrl_init(rtwdev, RTW89_PHY_0);
+}
+
+static void rtw8852a_bbrst_for_rfk(struct rtw89_dev *rtwdev,
+				   enum rtw89_phy_idx phy_idx)
+{
+	rtw89_phy_write32_set(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_TRK_EN);
+	rtw89_phy_write32_set(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_TRK_EN);
+	rtw8852a_bb_reset_all(rtwdev, phy_idx);
+	rtw89_phy_write32_clr(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_TRK_EN);
+	rtw89_phy_write32_clr(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_TRK_EN);
+	udelay(1);
+}
+
+static void rtw8852a_set_channel_bb(struct rtw89_dev *rtwdev,
+				    struct rtw89_channel_params *param,
+				    enum rtw89_phy_idx phy_idx)
+{
+	bool cck_en = param->center_chan > 14 ? false : true;
+	u8 pri_ch_idx = param->pri_ch_idx;
+
+	if (param->center_chan <= 14)
+		rtw8852a_ctrl_sco_cck(rtwdev, param->center_chan,
+				      param->primary_chan, param->bandwidth);
+
+	rtw8852a_ctrl_ch(rtwdev, param->center_chan, phy_idx);
+	rtw8852a_ctrl_bw(rtwdev, pri_ch_idx, param->bandwidth, phy_idx);
+	if (cck_en) {
+		rtw89_phy_write32_mask(rtwdev, R_RXCCA, B_RXCCA_DIS, 0);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_RXCCA, B_RXCCA_DIS, 1);
+		rtw8852a_bbrst_for_rfk(rtwdev, phy_idx);
+	}
+	rtw8852a_spur_elimination(rtwdev, param->center_chan);
+	rtw8852a_bb_reset_all(rtwdev, phy_idx);
+}
+
+static void rtw8852a_set_channel(struct rtw89_dev *rtwdev,
+				 struct rtw89_channel_params *params)
+{
+	rtw8852a_set_channel_mac(rtwdev, params, RTW89_MAC_0);
+	rtw8852a_set_channel_bb(rtwdev, params, RTW89_PHY_0);
+}
+
+static void rtw8852a_dfs_en(struct rtw89_dev *rtwdev, bool en)
+{
+	if (en)
+		rtw89_phy_write32_mask(rtwdev, R_UPD_P0, B_UPD_P0_EN, 1);
+	else
+		rtw89_phy_write32_mask(rtwdev, R_UPD_P0, B_UPD_P0_EN, 0);
+}
+
+static void rtw8852a_tssi_cont_en(struct rtw89_dev *rtwdev, bool en,
+				  enum rtw89_rf_path path)
+{
+	static const u32 tssi_trk[2] = {0x5818, 0x7818};
+	static const u32 ctrl_bbrst[2] = {0x58dc, 0x78dc};
+
+	if (en) {
+		rtw89_phy_write32_mask(rtwdev, ctrl_bbrst[path], BIT(30), 0x0);
+		rtw89_phy_write32_mask(rtwdev, tssi_trk[path], BIT(30), 0x0);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, ctrl_bbrst[path], BIT(30), 0x1);
+		rtw89_phy_write32_mask(rtwdev, tssi_trk[path], BIT(30), 0x1);
+	}
+}
+
+static void rtw8852a_tssi_cont_en_phyidx(struct rtw89_dev *rtwdev, bool en,
+					 u8 phy_idx)
+{
+	if (!rtwdev->dbcc_en) {
+		rtw8852a_tssi_cont_en(rtwdev, en, RF_PATH_A);
+		rtw8852a_tssi_cont_en(rtwdev, en, RF_PATH_B);
+	} else {
+		if (phy_idx == RTW89_PHY_0)
+			rtw8852a_tssi_cont_en(rtwdev, en, RF_PATH_A);
+		else
+			rtw8852a_tssi_cont_en(rtwdev, en, RF_PATH_B);
+	}
+}
+
+static void rtw8852a_adc_en(struct rtw89_dev *rtwdev, bool en)
+{
+	if (en)
+		rtw89_phy_write32_mask(rtwdev, R_ADC_FIFO, B_ADC_FIFO_RST,
+				       0x0);
+	else
+		rtw89_phy_write32_mask(rtwdev, R_ADC_FIFO, B_ADC_FIFO_RST,
+				       0xf);
+}
+
+static void rtw8852a_set_channel_help(struct rtw89_dev *rtwdev, bool enter,
+				      struct rtw89_channel_help_params *p)
+{
+	u8 phy_idx = RTW89_PHY_0;
+
+	if (enter) {
+		rtw89_mac_stop_sch_tx(rtwdev, RTW89_MAC_0, &p->tx_en, RTW89_SCH_TX_SEL_ALL);
+		rtw89_mac_cfg_ppdu_status(rtwdev, RTW89_MAC_0, false);
+		rtw8852a_dfs_en(rtwdev, false);
+		rtw8852a_tssi_cont_en_phyidx(rtwdev, false, RTW89_PHY_0);
+		rtw8852a_adc_en(rtwdev, false);
+		fsleep(40);
+		rtw8852a_bb_reset_en(rtwdev, phy_idx, false);
+	} else {
+		rtw89_mac_cfg_ppdu_status(rtwdev, RTW89_MAC_0, true);
+		rtw8852a_adc_en(rtwdev, true);
+		rtw8852a_dfs_en(rtwdev, true);
+		rtw8852a_tssi_cont_en_phyidx(rtwdev, true, RTW89_PHY_0);
+		rtw8852a_bb_reset_en(rtwdev, phy_idx, true);
+		rtw89_mac_resume_sch_tx(rtwdev, RTW89_MAC_0, p->tx_en);
+	}
+}
+
+static void rtw8852a_fem_setup(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_efuse *efuse = &rtwdev->efuse;
+
+	switch (efuse->rfe_type) {
+	case 11:
+	case 12:
+	case 17:
+	case 18:
+	case 51:
+	case 53:
+		rtwdev->fem.epa_2g = true;
+		rtwdev->fem.elna_2g = true;
+		fallthrough;
+	case 9:
+	case 10:
+	case 15:
+	case 16:
+		rtwdev->fem.epa_5g = true;
+		rtwdev->fem.elna_5g = true;
+		break;
+	default:
+		break;
+	}
+}
+
+static void rtw8852a_rfk_init(struct rtw89_dev *rtwdev)
+{
+	rtwdev->is_tssi_mode[RF_PATH_A] = false;
+	rtwdev->is_tssi_mode[RF_PATH_B] = false;
+
+	rtw8852a_rck(rtwdev);
+	rtw8852a_dack(rtwdev);
+	rtw8852a_rx_dck(rtwdev, RTW89_PHY_0, true);
+}
+
+static void rtw8852a_rfk_channel(struct rtw89_dev *rtwdev)
+{
+	enum rtw89_phy_idx phy_idx = RTW89_PHY_0;
+
+	rtw8852a_rx_dck(rtwdev, phy_idx, true);
+	rtw8852a_iqk(rtwdev, phy_idx);
+	rtw8852a_tssi(rtwdev, phy_idx);
+	rtw8852a_dpk(rtwdev, phy_idx);
+}
+
+static void rtw8852a_rfk_band_changed(struct rtw89_dev *rtwdev)
+{
+	rtw8852a_tssi_scan(rtwdev, RTW89_PHY_0);
+}
+
+static void rtw8852a_rfk_scan(struct rtw89_dev *rtwdev, bool start)
+{
+	rtw8852a_wifi_scan_notify(rtwdev, start, RTW89_PHY_0);
+}
+
+static void rtw8852a_rfk_track(struct rtw89_dev *rtwdev)
+{
+	rtw8852a_dpk_track(rtwdev);
+	rtw8852a_iqk_track(rtwdev);
+	rtw8852a_tssi_track(rtwdev);
+}
+
+static u32 rtw8852a_bb_cal_txpwr_ref(struct rtw89_dev *rtwdev,
+				     enum rtw89_phy_idx phy_idx, s16 ref)
+{
+	s8 ofst_int = 0;
+	u8 base_cw_0db = 0x27;
+	u16 tssi_16dbm_cw = 0x12c;
+	s16 pwr_s10_3 = 0;
+	s16 rf_pwr_cw = 0;
+	u16 bb_pwr_cw = 0;
+	u32 pwr_cw = 0;
+	u32 tssi_ofst_cw = 0;
+
+	pwr_s10_3 = (ref << 1) + (s16)(ofst_int) + (s16)(base_cw_0db << 3);
+	bb_pwr_cw = FIELD_GET(GENMASK(2, 0), pwr_s10_3);
+	rf_pwr_cw = FIELD_GET(GENMASK(8, 3), pwr_s10_3);
+	rf_pwr_cw = clamp_t(s16, rf_pwr_cw, 15, 63);
+	pwr_cw = (rf_pwr_cw << 3) | bb_pwr_cw;
+
+	tssi_ofst_cw = (u32)((s16)tssi_16dbm_cw + (ref << 1) - (16 << 3));
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR,
+		    "[TXPWR] tssi_ofst_cw=%d rf_cw=0x%x bb_cw=0x%x\n",
+		    tssi_ofst_cw, rf_pwr_cw, bb_pwr_cw);
+
+	return (tssi_ofst_cw << 18) | (pwr_cw << 9) | (ref & GENMASK(8, 0));
+}
+
+static
+void rtw8852a_set_txpwr_ul_tb_offset(struct rtw89_dev *rtwdev,
+				     s16 pw_ofst, enum rtw89_mac_idx mac_idx)
+{
+	s32 val_1t = 0;
+	s32 val_2t = 0;
+	u32 reg;
+
+	if (pw_ofst < -16 || pw_ofst > 15) {
+		rtw89_debug(rtwdev, RTW89_DBG_TXPWR, "[ULTB] Err pwr_offset=%d\n",
+			    pw_ofst);
+		return;
+	}
+	reg = rtw89_mac_reg_by_idx(R_AX_PWR_UL_TB_CTRL, mac_idx);
+	rtw89_write32_set(rtwdev, reg, B_AX_PWR_UL_TB_CTRL_EN);
+	val_1t = (s32)pw_ofst;
+	reg = rtw89_mac_reg_by_idx(R_AX_PWR_UL_TB_1T, mac_idx);
+	rtw89_write32_mask(rtwdev, reg, B_AX_PWR_UL_TB_1T_MASK, val_1t);
+	val_2t = max(val_1t - 3, -16);
+	reg = rtw89_mac_reg_by_idx(R_AX_PWR_UL_TB_2T, mac_idx);
+	rtw89_write32_mask(rtwdev, reg, B_AX_PWR_UL_TB_2T_MASK, val_2t);
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR, "[ULTB] Set TB pwr_offset=(%d, %d)\n",
+		    val_1t, val_2t);
+}
+
+static void rtw8852a_set_txpwr_ref(struct rtw89_dev *rtwdev,
+				   enum rtw89_phy_idx phy_idx)
+{
+	static const u32 addr[RF_PATH_NUM_8852A] = {0x5800, 0x7800};
+	const u32 mask = 0x7FFFFFF;
+	const u8 ofst_ofdm = 0x4;
+	const u8 ofst_cck = 0x8;
+	s16 ref_ofdm = 0;
+	s16 ref_cck = 0;
+	u32 val;
+	u8 i;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR, "[TXPWR] set txpwr reference\n");
+
+	rtw89_mac_txpwr_write32_mask(rtwdev, phy_idx, R_AX_PWR_RATE_CTRL,
+				     GENMASK(27, 10), 0x0);
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR, "[TXPWR] set bb ofdm txpwr ref\n");
+	val = rtw8852a_bb_cal_txpwr_ref(rtwdev, phy_idx, ref_ofdm);
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++)
+		rtw89_phy_write32_idx(rtwdev, addr[i] + ofst_ofdm, mask, val,
+				      phy_idx);
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR, "[TXPWR] set bb cck txpwr ref\n");
+	val = rtw8852a_bb_cal_txpwr_ref(rtwdev, phy_idx, ref_cck);
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++)
+		rtw89_phy_write32_idx(rtwdev, addr[i] + ofst_cck, mask, val,
+				      phy_idx);
+}
+
+static void rtw8852a_set_txpwr_byrate(struct rtw89_dev *rtwdev,
+				      enum rtw89_phy_idx phy_idx)
+{
+	u8 ch = rtwdev->hal.current_channel;
+	static const u8 rs[] = {
+		RTW89_RS_CCK,
+		RTW89_RS_OFDM,
+		RTW89_RS_MCS,
+		RTW89_RS_HEDCM,
+	};
+	s8 tmp;
+	u8 i, j;
+	u32 val, shf, addr = R_AX_PWR_BY_RATE;
+	struct rtw89_rate_desc cur;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR,
+		    "[TXPWR] set txpwr byrate with ch=%d\n", ch);
+
+	for (cur.nss = 0; cur.nss <= RTW89_NSS_2; cur.nss++) {
+		for (i = 0; i < ARRAY_SIZE(rs); i++) {
+			if (cur.nss >= rtw89_rs_nss_max[rs[i]])
+				continue;
+
+			val = 0;
+			cur.rs = rs[i];
+
+			for (j = 0; j < rtw89_rs_idx_max[rs[i]]; j++) {
+				cur.idx = j;
+				shf = (j % 4) * 8;
+				tmp = rtw89_phy_read_txpwr_byrate(rtwdev, &cur);
+				val |= (tmp << shf);
+
+				if ((j + 1) % 4)
+					continue;
+
+				rtw89_mac_txpwr_write32(rtwdev, phy_idx, addr, val);
+				val = 0;
+				addr += 4;
+			}
+		}
+	}
+}
+
+static void rtw8852a_set_txpwr_offset(struct rtw89_dev *rtwdev,
+				      enum rtw89_phy_idx phy_idx)
+{
+	struct rtw89_rate_desc desc = {
+		.nss = RTW89_NSS_1,
+		.rs = RTW89_RS_OFFSET,
+	};
+	u32 val = 0;
+	s8 v;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR, "[TXPWR] set txpwr offset\n");
+
+	for (desc.idx = 0; desc.idx < RTW89_RATE_OFFSET_MAX; desc.idx++) {
+		v = rtw89_phy_read_txpwr_byrate(rtwdev, &desc);
+		val |= ((v & 0xf) << (4 * desc.idx));
+	}
+
+	rtw89_mac_txpwr_write32_mask(rtwdev, phy_idx, R_AX_PWR_RATE_OFST_CTRL,
+				     GENMASK(19, 0), val);
+}
+
+static void rtw8852a_set_txpwr_limit(struct rtw89_dev *rtwdev,
+				     enum rtw89_phy_idx phy_idx)
+{
+#define __MAC_TXPWR_LMT_PAGE_SIZE 40
+	u8 ch = rtwdev->hal.current_channel;
+	u8 bw = rtwdev->hal.current_band_width;
+	struct rtw89_txpwr_limit lmt[NTX_NUM_8852A];
+	u32 addr, val;
+	const s8 *ptr;
+	u8 i, j, k;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR,
+		    "[TXPWR] set txpwr limit with ch=%d bw=%d\n", ch, bw);
+
+	for (i = 0; i < NTX_NUM_8852A; i++) {
+		rtw89_phy_fill_txpwr_limit(rtwdev, &lmt[i], i);
+
+		for (j = 0; j < __MAC_TXPWR_LMT_PAGE_SIZE; j += 4) {
+			addr = R_AX_PWR_LMT + j + __MAC_TXPWR_LMT_PAGE_SIZE * i;
+			ptr = (s8 *)&lmt[i] + j;
+			val = 0;
+
+			for (k = 0; k < 4; k++)
+				val |= (ptr[k] << (8 * k));
+
+			rtw89_mac_txpwr_write32(rtwdev, phy_idx, addr, val);
+		}
+	}
+#undef __MAC_TXPWR_LMT_PAGE_SIZE
+}
+
+static void rtw8852a_set_txpwr_limit_ru(struct rtw89_dev *rtwdev,
+					enum rtw89_phy_idx phy_idx)
+{
+#define __MAC_TXPWR_LMT_RU_PAGE_SIZE 24
+	u8 ch = rtwdev->hal.current_channel;
+	u8 bw = rtwdev->hal.current_band_width;
+	struct rtw89_txpwr_limit_ru lmt_ru[NTX_NUM_8852A];
+	u32 addr, val;
+	const s8 *ptr;
+	u8 i, j, k;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TXPWR,
+		    "[TXPWR] set txpwr limit ru with ch=%d bw=%d\n", ch, bw);
+
+	for (i = 0; i < NTX_NUM_8852A; i++) {
+		rtw89_phy_fill_txpwr_limit_ru(rtwdev, &lmt_ru[i], i);
+
+		for (j = 0; j < __MAC_TXPWR_LMT_RU_PAGE_SIZE; j += 4) {
+			addr = R_AX_PWR_RU_LMT + j +
+			       __MAC_TXPWR_LMT_RU_PAGE_SIZE * i;
+			ptr = (s8 *)&lmt_ru[i] + j;
+			val = 0;
+
+			for (k = 0; k < 4; k++)
+				val |= (ptr[k] << (8 * k));
+
+			rtw89_mac_txpwr_write32(rtwdev, phy_idx, addr, val);
+		}
+	}
+
+#undef __MAC_TXPWR_LMT_RU_PAGE_SIZE
+}
+
+static void rtw8852a_set_txpwr(struct rtw89_dev *rtwdev)
+{
+	rtw8852a_set_txpwr_byrate(rtwdev, RTW89_PHY_0);
+	rtw8852a_set_txpwr_limit(rtwdev, RTW89_PHY_0);
+	rtw8852a_set_txpwr_limit_ru(rtwdev, RTW89_PHY_0);
+}
+
+static void rtw8852a_set_txpwr_ctrl(struct rtw89_dev *rtwdev)
+{
+	rtw8852a_set_txpwr_ref(rtwdev, RTW89_PHY_0);
+	rtw8852a_set_txpwr_offset(rtwdev, RTW89_PHY_0);
+}
+
+static int
+rtw8852a_init_txpwr_unit(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx)
+{
+	int ret;
+
+	ret = rtw89_mac_txpwr_write32(rtwdev, phy_idx, R_AX_PWR_UL_CTRL2, 0x07763333);
+	if (ret)
+		return ret;
+
+	ret = rtw89_mac_txpwr_write32(rtwdev, phy_idx, R_AX_PWR_COEXT_CTRL, 0x01ebf004);
+	if (ret)
+		return ret;
+
+	ret = rtw89_mac_txpwr_write32(rtwdev, phy_idx, R_AX_PWR_UL_CTRL0, 0x0002f8ff);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+void rtw8852a_bb_set_plcp_tx(struct rtw89_dev *rtwdev)
+{
+	u8 i = 0;
+	u32 addr, val;
+
+	for (i = 0; i < ARRAY_SIZE(rtw8852a_pmac_ht20_mcs7_tbl); i++) {
+		addr = rtw8852a_pmac_ht20_mcs7_tbl[i].addr;
+		val = rtw8852a_pmac_ht20_mcs7_tbl[i].data;
+		rtw89_phy_write32(rtwdev, addr, val);
+	}
+}
+
+static void rtw8852a_stop_pmac_tx(struct rtw89_dev *rtwdev,
+				  struct rtw8852a_bb_pmac_info *tx_info,
+				  enum rtw89_phy_idx idx)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "PMAC Stop Tx");
+	if (tx_info->mode == CONT_TX)
+		rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_PRD, B_PMAC_CTX_EN, 0,
+				      idx);
+	else if (tx_info->mode == PKTS_TX)
+		rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_PRD, B_PMAC_PTX_EN, 0,
+				      idx);
+}
+
+static void rtw8852a_start_pmac_tx(struct rtw89_dev *rtwdev,
+				   struct rtw8852a_bb_pmac_info *tx_info,
+				   enum rtw89_phy_idx idx)
+{
+	enum rtw8852a_pmac_mode mode = tx_info->mode;
+	u32 pkt_cnt = tx_info->tx_cnt;
+	u16 period = tx_info->period;
+
+	if (mode == CONT_TX && !tx_info->is_cck) {
+		rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_PRD, B_PMAC_CTX_EN, 1,
+				      idx);
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI, "PMAC CTx Start");
+	} else if (mode == PKTS_TX) {
+		rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_PRD, B_PMAC_PTX_EN, 1,
+				      idx);
+		rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_PRD,
+				      B_PMAC_TX_PRD_MSK, period, idx);
+		rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_CNT, B_PMAC_TX_CNT_MSK,
+				      pkt_cnt, idx);
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI, "PMAC PTx Start");
+	}
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_CTRL, B_PMAC_TXEN_DIS, 1, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_TX_CTRL, B_PMAC_TXEN_DIS, 0, idx);
+}
+
+void rtw8852a_bb_set_pmac_tx(struct rtw89_dev *rtwdev,
+			     struct rtw8852a_bb_pmac_info *tx_info,
+			     enum rtw89_phy_idx idx)
+{
+	if (!tx_info->en_pmac_tx) {
+		rtw8852a_stop_pmac_tx(rtwdev, tx_info, idx);
+		rtw89_phy_write32_idx(rtwdev, R_PD_CTRL, B_PD_HIT_DIS, 0, idx);
+		if (rtwdev->hal.current_band_type == RTW89_BAND_2G)
+			rtw89_phy_write32_clr(rtwdev, R_RXCCA, B_RXCCA_DIS);
+		return;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "PMAC Tx Enable");
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_GNT, B_PMAC_GNT_TXEN, 1, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_GNT, B_PMAC_GNT_RXEN, 1, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_RX_CFG1, B_PMAC_OPT1_MSK, 0x3f,
+			      idx);
+	rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PD_CTRL, B_PD_HIT_DIS, 1, idx);
+	rtw89_phy_write32_set(rtwdev, R_RXCCA, B_RXCCA_DIS);
+	rtw89_phy_write32_idx(rtwdev, R_RSTB_ASYNC, B_RSTB_ASYNC_ALL, 1, idx);
+	rtw8852a_start_pmac_tx(rtwdev, tx_info, idx);
+}
+
+void rtw8852a_bb_set_pmac_pkt_tx(struct rtw89_dev *rtwdev, u8 enable,
+				 u16 tx_cnt, u16 period, u16 tx_time,
+				 enum rtw89_phy_idx idx)
+{
+	struct rtw8852a_bb_pmac_info tx_info = {0};
+
+	tx_info.en_pmac_tx = enable;
+	tx_info.is_cck = 0;
+	tx_info.mode = PKTS_TX;
+	tx_info.tx_cnt = tx_cnt;
+	tx_info.period = period;
+	tx_info.tx_time = tx_time;
+	rtw8852a_bb_set_pmac_tx(rtwdev, &tx_info, idx);
+}
+
+void rtw8852a_bb_set_power(struct rtw89_dev *rtwdev, s16 pwr_dbm,
+			   enum rtw89_phy_idx idx)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "PMAC CFG Tx PWR = %d", pwr_dbm);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_PWR_EN, 1, idx);
+	rtw89_phy_write32_idx(rtwdev, R_TXPWR, B_TXPWR_MSK, pwr_dbm, idx);
+}
+
+void rtw8852a_bb_cfg_tx_path(struct rtw89_dev *rtwdev, u8 tx_path)
+{
+	u32 rst_mask0 = 0;
+	u32 rst_mask1 = 0;
+
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_MOD, 7, RTW89_PHY_0);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_MOD, 7, RTW89_PHY_1);
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "PMAC CFG Tx Path = %d", tx_path);
+	if (!rtwdev->dbcc_en) {
+		if (tx_path == RF_PATH_A) {
+			rtw89_phy_write32_mask(rtwdev, R_TXPATH_SEL,
+					       B_TXPATH_SEL_MSK, 1);
+			rtw89_phy_write32_mask(rtwdev, R_TXNSS_MAP,
+					       B_TXNSS_MAP_MSK, 0);
+		} else if (tx_path == RF_PATH_B) {
+			rtw89_phy_write32_mask(rtwdev, R_TXPATH_SEL,
+					       B_TXPATH_SEL_MSK, 2);
+			rtw89_phy_write32_mask(rtwdev, R_TXNSS_MAP,
+					       B_TXNSS_MAP_MSK, 0);
+		} else if (tx_path == RF_PATH_AB) {
+			rtw89_phy_write32_mask(rtwdev, R_TXPATH_SEL,
+					       B_TXPATH_SEL_MSK, 3);
+			rtw89_phy_write32_mask(rtwdev, R_TXNSS_MAP,
+					       B_TXNSS_MAP_MSK, 4);
+		} else {
+			rtw89_debug(rtwdev, RTW89_DBG_TSSI, "Error Tx Path");
+		}
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_TXPATH_SEL, B_TXPATH_SEL_MSK,
+				       1);
+		rtw89_phy_write32_idx(rtwdev, R_TXPATH_SEL, B_TXPATH_SEL_MSK, 2,
+				      RTW89_PHY_1);
+		rtw89_phy_write32_mask(rtwdev, R_TXNSS_MAP, B_TXNSS_MAP_MSK,
+				       0);
+		rtw89_phy_write32_idx(rtwdev, R_TXNSS_MAP, B_TXNSS_MAP_MSK, 4,
+				      RTW89_PHY_1);
+	}
+	rst_mask0 = B_P0_TXPW_RSTB_MANON | B_P0_TXPW_RSTB_TSSI;
+	rst_mask1 = B_P1_TXPW_RSTB_MANON | B_P1_TXPW_RSTB_TSSI;
+	if (tx_path == RF_PATH_A) {
+		rtw89_phy_write32_mask(rtwdev, R_P0_TXPW_RSTB, rst_mask0, 1);
+		rtw89_phy_write32_mask(rtwdev, R_P0_TXPW_RSTB, rst_mask0, 3);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_P1_TXPW_RSTB, rst_mask1, 1);
+		rtw89_phy_write32_mask(rtwdev, R_P1_TXPW_RSTB, rst_mask1, 3);
+	}
+}
+
+void rtw8852a_bb_tx_mode_switch(struct rtw89_dev *rtwdev,
+				enum rtw89_phy_idx idx, u8 mode)
+{
+	if (mode != 0)
+		return;
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "Tx mode switch");
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_GNT, B_PMAC_GNT_TXEN, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_GNT, B_PMAC_GNT_RXEN, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_RX_CFG1, B_PMAC_OPT1_MSK, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_PMAC_RXMOD, B_PMAC_RXMOD_MSK, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_DPD_EN, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_MOD, 0, idx);
+	rtw89_phy_write32_idx(rtwdev, R_MAC_SEL, B_MAC_SEL_PWR_EN, 0, idx);
+}
+
+static void rtw8852a_bb_ctrl_btc_preagc(struct rtw89_dev *rtwdev, bool bt_en)
+{
+	rtw89_phy_write_reg3_tbl(rtwdev, bt_en ? &rtw8852a_btc_preagc_en_defs_tbl :
+						 &rtw8852a_btc_preagc_dis_defs_tbl);
+}
+
+static u8 rtw8852a_get_thermal(struct rtw89_dev *rtwdev, enum rtw89_rf_path rf_path)
+{
+	if (rtwdev->is_tssi_mode[rf_path]) {
+		u32 addr = 0x1c10 + (rf_path << 13);
+
+		return (u8)rtw89_phy_read32_mask(rtwdev, addr, 0x3F000000);
+	}
+
+	rtw89_write_rf(rtwdev, rf_path, RR_TM, RR_TM_TRI, 0x1);
+	rtw89_write_rf(rtwdev, rf_path, RR_TM, RR_TM_TRI, 0x0);
+	rtw89_write_rf(rtwdev, rf_path, RR_TM, RR_TM_TRI, 0x1);
+
+	fsleep(200);
+
+	return (u8)rtw89_read_rf(rtwdev, rf_path, RR_TM, RR_TM_VAL);
+}
+
+static void rtw8852a_btc_set_rfe(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_module *module = &btc->mdinfo;
+
+	module->rfe_type = rtwdev->efuse.rfe_type;
+	module->cv = rtwdev->hal.cv;
+	module->bt_solo = 0;
+	module->switch_type = BTC_SWITCH_INTERNAL;
+
+	if (module->rfe_type > 0)
+		module->ant.num = (module->rfe_type % 2 ? 2 : 3);
+	else
+		module->ant.num = 2;
+
+	module->ant.diversity = 0;
+	module->ant.isolation = 10;
+
+	if (module->ant.num == 3) {
+		module->ant.type = BTC_ANT_DEDICATED;
+		module->bt_pos = BTC_BT_ALONE;
+	} else {
+		module->ant.type = BTC_ANT_SHARED;
+		module->bt_pos = BTC_BT_BTG;
+	}
+}
+
+static
+void rtw8852a_set_trx_mask(struct rtw89_dev *rtwdev, u8 path, u8 group, u32 val)
+{
+	rtw89_write_rf(rtwdev, path, RR_LUTWE, 0xfffff, 0x20000);
+	rtw89_write_rf(rtwdev, path, RR_LUTWA, 0xfffff, group);
+	rtw89_write_rf(rtwdev, path, RR_LUTWD0, 0xfffff, val);
+	rtw89_write_rf(rtwdev, path, RR_LUTWE, 0xfffff, 0x0);
+}
+
+static void rtw8852a_ctrl_btg(struct rtw89_dev *rtwdev, bool btg)
+{
+	if (btg) {
+		rtw89_phy_write32_mask(rtwdev, R_PATH0_BTG, B_PATH0_BTG_SHEN, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_PATH1_BTG, B_PATH1_BTG_SHEN, 0x3);
+		rtw89_phy_write32_mask(rtwdev, R_PMAC_GNT, B_PMAC_GNT_P1, 0x0);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_PATH0_BTG, B_PATH0_BTG_SHEN, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_PATH1_BTG, B_PATH1_BTG_SHEN, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_PMAC_GNT, B_PMAC_GNT_P1, 0xf);
+		rtw89_phy_write32_mask(rtwdev, R_PMAC_GNT, B_PMAC_GNT_P2, 0x4);
+	}
+}
+
+static void rtw8852a_btc_init_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_module *module = &btc->mdinfo;
+	const struct rtw89_chip_info *chip = rtwdev->chip;
+	const struct rtw89_mac_ax_coex coex_params = {
+		.pta_mode = RTW89_MAC_AX_COEX_RTK_MODE,
+		.direction = RTW89_MAC_AX_COEX_INNER,
+	};
+
+	/* PTA init  */
+	rtw89_mac_coex_init(rtwdev, &coex_params);
+
+	/* set WL Tx response = Hi-Pri */
+	chip->ops->btc_set_wl_pri(rtwdev, BTC_PRI_MASK_TX_RESP, true);
+	chip->ops->btc_set_wl_pri(rtwdev, BTC_PRI_MASK_BEACON, true);
+
+	/* set rf gnt debug off */
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_WLSEL, 0xfffff, 0x0);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_WLSEL, 0xfffff, 0x0);
+
+	/* set WL Tx thru in TRX mask table if GNT_WL = 0 && BT_S1 = ss group */
+	if (module->ant.type == BTC_ANT_SHARED) {
+		rtw8852a_set_trx_mask(rtwdev,
+				      RF_PATH_A, BTC_BT_SS_GROUP, 0x5ff);
+		rtw8852a_set_trx_mask(rtwdev,
+				      RF_PATH_B, BTC_BT_SS_GROUP, 0x5ff);
+	} else { /* set WL Tx stb if GNT_WL = 0 && BT_S1 = ss group for 3-ant */
+		rtw8852a_set_trx_mask(rtwdev,
+				      RF_PATH_A, BTC_BT_SS_GROUP, 0x5df);
+		rtw8852a_set_trx_mask(rtwdev,
+				      RF_PATH_B, BTC_BT_SS_GROUP, 0x5df);
+	}
+
+	/* set PTA break table */
+	rtw89_write32(rtwdev, R_BTC_BREAK_TABLE, BTC_BREAK_PARAM);
+
+	 /* enable BT counter 0xda40[16,2] = 2b'11 */
+	rtw89_write32_set(rtwdev,
+			  R_AX_CSR_MODE, B_AX_BT_CNT_RST | B_AX_STATIS_BT_EN);
+	btc->cx.wl.status.map.init_ok = true;
+}
+
+static
+void rtw8852a_btc_set_wl_pri(struct rtw89_dev *rtwdev, u8 map, bool state)
+{
+	u32 bitmap = 0;
+	u32 reg = 0;
+
+	switch (map) {
+	case BTC_PRI_MASK_TX_RESP:
+		reg = R_BTC_BT_COEX_MSK_TABLE;
+		bitmap = B_BTC_PRI_MASK_TX_RESP_V1;
+		break;
+	case BTC_PRI_MASK_BEACON:
+		reg = R_AX_WL_PRI_MSK;
+		bitmap = B_AX_PTA_WL_PRI_MASK_BCNQ;
+		break;
+	default:
+		return;
+	}
+
+	if (state)
+		rtw89_write32_set(rtwdev, reg, bitmap);
+	else
+		rtw89_write32_clr(rtwdev, reg, bitmap);
+}
+
+static inline u32 __btc_ctrl_val_all_time(u32 ctrl)
+{
+	return FIELD_GET(GENMASK(15, 0), ctrl);
+}
+
+static inline u32 __btc_ctrl_rst_all_time(u32 cur)
+{
+	return cur & ~B_AX_FORCE_PWR_BY_RATE_EN;
+}
+
+static inline u32 __btc_ctrl_gen_all_time(u32 cur, u32 val)
+{
+	u32 hv = cur & ~B_AX_FORCE_PWR_BY_RATE_VALUE_MASK;
+	u32 lv = val & B_AX_FORCE_PWR_BY_RATE_VALUE_MASK;
+
+	return hv | lv | B_AX_FORCE_PWR_BY_RATE_EN;
+}
+
+static inline u32 __btc_ctrl_val_gnt_bt(u32 ctrl)
+{
+	return FIELD_GET(GENMASK(31, 16), ctrl);
+}
+
+static inline u32 __btc_ctrl_rst_gnt_bt(u32 cur)
+{
+	return cur & ~B_AX_TXAGC_BT_EN;
+}
+
+static inline u32 __btc_ctrl_gen_gnt_bt(u32 cur, u32 val)
+{
+	u32 ov = cur & ~B_AX_TXAGC_BT_MASK;
+	u32 iv = FIELD_PREP(B_AX_TXAGC_BT_MASK, val);
+
+	return ov | iv | B_AX_TXAGC_BT_EN;
+}
+
+static void
+rtw8852a_btc_set_wl_txpwr_ctrl(struct rtw89_dev *rtwdev, u32 txpwr_val)
+{
+	const u32 __btc_cr_all_time = R_AX_PWR_RATE_CTRL;
+	const u32 __btc_cr_gnt_bt = R_AX_PWR_COEXT_CTRL;
+
+#define __do_clr(_chk) ((_chk) == GENMASK(15, 0))
+#define __handle(_case)							\
+	do {								\
+		const u32 _reg = __btc_cr_ ## _case;			\
+		u32 _val = __btc_ctrl_val_ ## _case(txpwr_val);		\
+		u32 _cur, _wrt;						\
+		rtw89_debug(rtwdev, RTW89_DBG_TXPWR,			\
+			    "btc ctrl %s: 0x%x\n", #_case, _val);	\
+		rtw89_mac_txpwr_read32(rtwdev, RTW89_PHY_0, _reg, &_cur);\
+		rtw89_debug(rtwdev, RTW89_DBG_TXPWR,			\
+			    "btc ctrl ori 0x%x: 0x%x\n", _reg, _cur);	\
+		_wrt = __do_clr(_val) ?					\
+			__btc_ctrl_rst_ ## _case(_cur) :		\
+			__btc_ctrl_gen_ ## _case(_cur, _val);		\
+		rtw89_mac_txpwr_write32(rtwdev, RTW89_PHY_0, _reg, _wrt);\
+		rtw89_debug(rtwdev, RTW89_DBG_TXPWR,			\
+			    "btc ctrl set 0x%x: 0x%x\n", _reg, _wrt);	\
+	} while (0)
+
+	__handle(all_time);
+	__handle(gnt_bt);
+
+#undef __handle
+#undef __do_clr
+}
+
+static
+s8 rtw8852a_btc_get_bt_rssi(struct rtw89_dev *rtwdev, s8 val)
+{
+	return clamp_t(s8, val, -100, 0) + 100;
+}
+
+static struct rtw89_btc_rf_trx_para rtw89_btc_8852a_rf_ul[] = {
+	{255, 0, 0, 7}, /* 0 -> original */
+	{255, 2, 0, 7}, /* 1 -> for BT-connected ACI issue && BTG co-rx */
+	{255, 0, 0, 7}, /* 2 ->reserved for shared-antenna */
+	{255, 0, 0, 7}, /* 3- >reserved for shared-antenna */
+	{255, 0, 0, 7}, /* 4 ->reserved for shared-antenna */
+	{255, 0, 0, 7}, /* the below id is for non-shared-antenna free-run */
+	{6, 1, 0, 7},
+	{13, 1, 0, 7},
+	{13, 1, 0, 7}
+};
+
+static struct rtw89_btc_rf_trx_para rtw89_btc_8852a_rf_dl[] = {
+	{255, 0, 0, 7}, /* 0 -> original */
+	{255, 2, 0, 7}, /* 1 -> reserved for shared-antenna */
+	{255, 0, 0, 7}, /* 2 ->reserved for shared-antenna */
+	{255, 0, 0, 7}, /* 3- >reserved for shared-antenna */
+	{255, 0, 0, 7}, /* 4 ->reserved for shared-antenna */
+	{255, 0, 0, 7}, /* the below id is for non-shared-antenna free-run */
+	{255, 1, 0, 7},
+	{255, 1, 0, 7},
+	{255, 1, 0, 7}
+};
+
+static const
+u8 rtw89_btc_8852a_wl_rssi_thres[BTC_WL_RSSI_THMAX] = {60, 50, 40, 30};
+static const
+u8 rtw89_btc_8852a_bt_rssi_thres[BTC_BT_RSSI_THMAX] = {40, 36, 31, 28};
+
+static struct rtw89_btc_fbtc_mreg rtw89_btc_8852a_mon_reg[] = {
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda24),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda28),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda2c),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda30),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda4c),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda10),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda20),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xda34),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0xcef4),
+	RTW89_DEF_FBTC_MREG(REG_MAC, 4, 0x8424),
+	RTW89_DEF_FBTC_MREG(REG_BB, 4, 0x980),
+	RTW89_DEF_FBTC_MREG(REG_BT_MODEM, 4, 0x178),
+};
+
+static
+void rtw8852a_btc_bt_aci_imp(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_dm *dm = &btc->dm;
+	struct rtw89_btc_bt_info *bt = &btc->cx.bt;
+	struct rtw89_btc_bt_link_info *b = &bt->link_info;
+
+	/* fix LNA2 = level-5 for BT ACI issue at BTG */
+	if (btc->dm.wl_btg_rx && b->profile_cnt.now != 0)
+		dm->trx_para_level = 1;
+}
+
+static
+void rtw8852a_btc_update_bt_cnt(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_btc *btc = &rtwdev->btc;
+	struct rtw89_btc_cx *cx = &btc->cx;
+	u32 val;
+
+	val = rtw89_read32(rtwdev, R_AX_BT_STAST_HIGH);
+	cx->cnt_bt[BTC_BCNT_HIPRI_TX] = FIELD_GET(B_AX_STATIS_BT_HI_TX_MASK, val);
+	cx->cnt_bt[BTC_BCNT_HIPRI_RX] = FIELD_GET(B_AX_STATIS_BT_HI_RX_MASK, val);
+
+	val = rtw89_read32(rtwdev, R_AX_BT_STAST_LOW);
+	cx->cnt_bt[BTC_BCNT_LOPRI_TX] = FIELD_GET(B_AX_STATIS_BT_LO_TX_1_MASK, val);
+	cx->cnt_bt[BTC_BCNT_LOPRI_RX] = FIELD_GET(B_AX_STATIS_BT_LO_RX_1_MASK, val);
+
+	/* clock-gate off before reset counter*/
+	rtw89_write32_set(rtwdev, R_AX_BTC_CFG, B_AX_DIS_BTC_CLK_G);
+	rtw89_write32_clr(rtwdev, R_AX_CSR_MODE, B_AX_BT_CNT_RST);
+	rtw89_write32_set(rtwdev, R_AX_CSR_MODE, B_AX_BT_CNT_RST);
+	rtw89_write32_clr(rtwdev, R_AX_BTC_CFG, B_AX_DIS_BTC_CLK_G);
+}
+
+static
+void rtw8852a_btc_wl_s1_standby(struct rtw89_dev *rtwdev, bool state)
+{
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_LUTWE, RFREG_MASK, 0x80000);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_LUTWA, RFREG_MASK, 0x1);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_LUTWD1, RFREG_MASK, 0x1);
+
+	/* set WL standby = Rx for GNT_BT_Tx = 1->0 settle issue */
+	if (state)
+		rtw89_write_rf(rtwdev, RF_PATH_B, RR_LUTWD0,
+			       RFREG_MASK, 0xa2d7c);
+	else
+		rtw89_write_rf(rtwdev, RF_PATH_B, RR_LUTWD0,
+			       RFREG_MASK, 0xa2020);
+
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_LUTWE, RFREG_MASK, 0x0);
+}
+
+static void rtw8852a_query_ppdu(struct rtw89_dev *rtwdev,
+				struct rtw89_rx_phy_ppdu *phy_ppdu,
+				struct ieee80211_rx_status *status)
+{
+	u8 path;
+	s8 *rx_power = phy_ppdu->rssi;
+
+	status->signal = max_t(s8, rx_power[RF_PATH_A], rx_power[RF_PATH_B]);
+	for (path = 0; path < rtwdev->chip->rf_path_num; path++) {
+		status->chains |= BIT(path);
+		status->chain_signal[path] = rx_power[path];
+	}
+}
+
+static const struct rtw89_chip_ops rtw8852a_chip_ops = {
+	.bb_reset		= rtw8852a_bb_reset,
+	.bb_sethw		= rtw8852a_bb_sethw,
+	.read_rf		= rtw89_phy_read_rf,
+	.write_rf		= rtw89_phy_write_rf,
+	.set_channel		= rtw8852a_set_channel,
+	.set_channel_help	= rtw8852a_set_channel_help,
+	.read_efuse		= rtw8852a_read_efuse,
+	.read_phycap		= rtw8852a_read_phycap,
+	.fem_setup		= rtw8852a_fem_setup,
+	.rfk_init		= rtw8852a_rfk_init,
+	.rfk_channel		= rtw8852a_rfk_channel,
+	.rfk_band_changed	= rtw8852a_rfk_band_changed,
+	.rfk_scan		= rtw8852a_rfk_scan,
+	.rfk_track		= rtw8852a_rfk_track,
+	.power_trim		= rtw8852a_power_trim,
+	.set_txpwr		= rtw8852a_set_txpwr,
+	.set_txpwr_ctrl		= rtw8852a_set_txpwr_ctrl,
+	.init_txpwr_unit	= rtw8852a_init_txpwr_unit,
+	.get_thermal		= rtw8852a_get_thermal,
+	.ctrl_btg		= rtw8852a_ctrl_btg,
+	.query_ppdu		= rtw8852a_query_ppdu,
+	.bb_ctrl_btc_preagc	= rtw8852a_bb_ctrl_btc_preagc,
+	.set_txpwr_ul_tb_offset	= rtw8852a_set_txpwr_ul_tb_offset,
+
+	.btc_set_rfe		= rtw8852a_btc_set_rfe,
+	.btc_init_cfg		= rtw8852a_btc_init_cfg,
+	.btc_set_wl_pri		= rtw8852a_btc_set_wl_pri,
+	.btc_set_wl_txpwr_ctrl	= rtw8852a_btc_set_wl_txpwr_ctrl,
+	.btc_get_bt_rssi	= rtw8852a_btc_get_bt_rssi,
+	.btc_bt_aci_imp		= rtw8852a_btc_bt_aci_imp,
+	.btc_update_bt_cnt	= rtw8852a_btc_update_bt_cnt,
+	.btc_wl_s1_standby	= rtw8852a_btc_wl_s1_standby,
+};
+
+const struct rtw89_chip_info rtw8852a_chip_info = {
+	.chip_id		= RTL8852A,
+	.ops			= &rtw8852a_chip_ops,
+	.fw_name		= "rtw89/rtw8852a_fw.bin",
+	.fifo_size		= 458752,
+	.max_amsdu_limit	= 3500,
+	.dis_2g_40m_ul_ofdma	= true,
+	.hfc_param_ini		= rtw8852a_hfc_param_ini_pcie,
+	.dle_mem		= rtw8852a_dle_mem_pcie,
+	.rf_base_addr		= {0xc000, 0xd000},
+	.pwr_on_seq		= pwr_on_seq_8852a,
+	.pwr_off_seq		= pwr_off_seq_8852a,
+	.bb_table		= &rtw89_8852a_phy_bb_table,
+	.rf_table		= {&rtw89_8852a_phy_radioa_table,
+				   &rtw89_8852a_phy_radiob_table,},
+	.nctl_table		= &rtw89_8852a_phy_nctl_table,
+	.byr_table		= &rtw89_8852a_byr_table,
+	.txpwr_lmt_2g		= &rtw89_8852a_txpwr_lmt_2g,
+	.txpwr_lmt_5g		= &rtw89_8852a_txpwr_lmt_5g,
+	.txpwr_lmt_ru_2g	= &rtw89_8852a_txpwr_lmt_ru_2g,
+	.txpwr_lmt_ru_5g	= &rtw89_8852a_txpwr_lmt_ru_5g,
+	.txpwr_factor_rf	= 2,
+	.txpwr_factor_mac	= 1,
+	.dig_table		= &rtw89_8852a_phy_dig_table,
+	.rf_path_num		= 2,
+	.tx_nss			= 2,
+	.rx_nss			= 2,
+	.acam_num		= 128,
+	.bcam_num		= 10,
+	.scam_num		= 128,
+	.sec_ctrl_efuse_size	= 4,
+	.physical_efuse_size	= 1216,
+	.logical_efuse_size	= 1536,
+	.limit_efuse_size	= 1152,
+	.phycap_addr		= 0x580,
+	.phycap_size		= 128,
+	.para_ver		= 0x05050764,
+	.wlcx_desired		= 0x05050000,
+	.btcx_desired		= 0x5,
+	.scbd			= 0x1,
+	.mailbox		= 0x1,
+	.afh_guard_ch		= 6,
+	.wl_rssi_thres		= rtw89_btc_8852a_wl_rssi_thres,
+	.bt_rssi_thres		= rtw89_btc_8852a_bt_rssi_thres,
+	.rssi_tol		= 2,
+	.mon_reg_num		= ARRAY_SIZE(rtw89_btc_8852a_mon_reg),
+	.mon_reg		= rtw89_btc_8852a_mon_reg,
+	.rf_para_ulink_num	= ARRAY_SIZE(rtw89_btc_8852a_rf_ul),
+	.rf_para_ulink		= rtw89_btc_8852a_rf_ul,
+	.rf_para_dlink_num	= ARRAY_SIZE(rtw89_btc_8852a_rf_dl),
+	.rf_para_dlink		= rtw89_btc_8852a_rf_dl,
+	.ps_mode_supported	= BIT(RTW89_PS_MODE_RFOFF) |
+				  BIT(RTW89_PS_MODE_CLK_GATED) |
+				  BIT(RTW89_PS_MODE_PWR_GATED),
+};
+EXPORT_SYMBOL(rtw8852a_chip_info);
+
+MODULE_FIRMWARE("rtw89/rtw8852a_fw.bin");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a.h
@@ -0,0 +1,109 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_8852A_H__
+#define __RTW89_8852A_H__
+
+#include "core.h"
+
+#define RF_PATH_NUM_8852A 2
+#define NTX_NUM_8852A 2
+
+enum rtw8852a_pmac_mode {
+	NONE_TEST,
+	PKTS_TX,
+	PKTS_RX,
+	CONT_TX
+};
+
+struct rtw8852au_efuse {
+	u8 rsvd[0x38];
+	u8 mac_addr[ETH_ALEN];
+};
+
+struct rtw8852ae_efuse {
+	u8 mac_addr[ETH_ALEN];
+};
+
+struct rtw8852a_tssi_offset {
+	u8 cck_tssi[TSSI_CCK_CH_GROUP_NUM];
+	u8 bw40_tssi[TSSI_MCS_2G_CH_GROUP_NUM];
+	u8 rsvd[7];
+	u8 bw40_1s_tssi_5g[TSSI_MCS_5G_CH_GROUP_NUM];
+} __packed;
+
+struct rtw8852a_efuse {
+	u8 rsvd[0x210];
+	struct rtw8852a_tssi_offset path_a_tssi;
+	u8 rsvd1[10];
+	struct rtw8852a_tssi_offset path_b_tssi;
+	u8 rsvd2[94];
+	u8 channel_plan;
+	u8 xtal_k;
+	u8 rsvd3;
+	u8 iqk_lck;
+	u8 rsvd4[5];
+	u8 reg_setting:2;
+	u8 tx_diversity:1;
+	u8 rx_diversity:2;
+	u8 ac_mode:1;
+	u8 module_type:2;
+	u8 rsvd5;
+	u8 shared_ant:1;
+	u8 coex_type:3;
+	u8 ant_iso:1;
+	u8 radio_on_off:1;
+	u8 rsvd6:2;
+	u8 eeprom_version;
+	u8 customer_id;
+	u8 tx_bb_swing_2g;
+	u8 tx_bb_swing_5g;
+	u8 tx_cali_pwr_trk_mode;
+	u8 trx_path_selection;
+	u8 rfe_type;
+	u8 country_code[2];
+	u8 rsvd7[3];
+	u8 path_a_therm;
+	u8 path_b_therm;
+	u8 rsvd8[46];
+	u8 path_a_cck_pwr_idx[6];
+	u8 path_a_bw40_1tx_pwr_idx[5];
+	u8 path_a_ofdm_1tx_pwr_idx_diff:4;
+	u8 path_a_bw20_1tx_pwr_idx_diff:4;
+	u8 path_a_bw20_2tx_pwr_idx_diff:4;
+	u8 path_a_bw40_2tx_pwr_idx_diff:4;
+	u8 path_a_cck_2tx_pwr_idx_diff:4;
+	u8 path_a_ofdm_2tx_pwr_idx_diff:4;
+	u8 rsvd9[0xf2];
+	union {
+		struct rtw8852au_efuse u;
+		struct rtw8852ae_efuse e;
+	};
+} __packed;
+
+struct rtw8852a_bb_pmac_info {
+	u8 en_pmac_tx:1;
+	u8 is_cck:1;
+	u8 mode:3;
+	u8 rsvd:3;
+	u16 tx_cnt;
+	u16 period;
+	u16 tx_time;
+	u8 duty_cycle;
+};
+
+void rtw8852a_bb_set_plcp_tx(struct rtw89_dev *rtwdev);
+void rtw8852a_bb_set_pmac_tx(struct rtw89_dev *rtwdev,
+			     struct rtw8852a_bb_pmac_info *tx_info,
+			     enum rtw89_phy_idx idx);
+void rtw8852a_bb_set_pmac_pkt_tx(struct rtw89_dev *rtwdev, u8 enable,
+				 u16 tx_cnt, u16 period, u16 tx_time,
+				 enum rtw89_phy_idx idx);
+void rtw8852a_bb_set_power(struct rtw89_dev *rtwdev, s16 pwr_dbm,
+			   enum rtw89_phy_idx idx);
+void rtw8852a_bb_cfg_tx_path(struct rtw89_dev *rtwdev, u8 tx_path);
+void rtw8852a_bb_tx_mode_switch(struct rtw89_dev *rtwdev,
+				enum rtw89_phy_idx idx, u8 mode);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk.c
@@ -0,0 +1,3911 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "coex.h"
+#include "debug.h"
+#include "mac.h"
+#include "phy.h"
+#include "reg.h"
+#include "rtw8852a.h"
+#include "rtw8852a_rfk.h"
+#include "rtw8852a_rfk_table.h"
+#include "rtw8852a_table.h"
+
+static void
+_rfk_write_rf(struct rtw89_dev *rtwdev, const struct rtw89_reg5_def *def)
+{
+	rtw89_write_rf(rtwdev, def->path, def->addr, def->mask, def->data);
+}
+
+static void
+_rfk_write32_mask(struct rtw89_dev *rtwdev, const struct rtw89_reg5_def *def)
+{
+	rtw89_phy_write32_mask(rtwdev, def->addr, def->mask, def->data);
+}
+
+static void
+_rfk_write32_set(struct rtw89_dev *rtwdev, const struct rtw89_reg5_def *def)
+{
+	rtw89_phy_write32_set(rtwdev, def->addr, def->mask);
+}
+
+static void
+_rfk_write32_clr(struct rtw89_dev *rtwdev, const struct rtw89_reg5_def *def)
+{
+	rtw89_phy_write32_clr(rtwdev, def->addr, def->mask);
+}
+
+static void
+_rfk_delay(struct rtw89_dev *rtwdev, const struct rtw89_reg5_def *def)
+{
+	udelay(def->data);
+}
+
+static void
+(*_rfk_handler[])(struct rtw89_dev *rtwdev, const struct rtw89_reg5_def *def) = {
+	[RTW89_RFK_F_WRF] = _rfk_write_rf,
+	[RTW89_RFK_F_WM] = _rfk_write32_mask,
+	[RTW89_RFK_F_WS] = _rfk_write32_set,
+	[RTW89_RFK_F_WC] = _rfk_write32_clr,
+	[RTW89_RFK_F_DELAY] = _rfk_delay,
+};
+
+static_assert(ARRAY_SIZE(_rfk_handler) == RTW89_RFK_F_NUM);
+
+static void
+rtw89_rfk_parser(struct rtw89_dev *rtwdev, const struct rtw89_rfk_tbl *tbl)
+{
+	const struct rtw89_reg5_def *p = tbl->defs;
+	const struct rtw89_reg5_def *end = tbl->defs + tbl->size;
+
+	for (; p < end; p++)
+		_rfk_handler[p->flag](rtwdev, p);
+}
+
+#define rtw89_rfk_parser_by_cond(rtwdev, cond, tbl_t, tbl_f)	\
+	do {							\
+		typeof(rtwdev) _dev = (rtwdev);			\
+		if (cond)					\
+			rtw89_rfk_parser(_dev, (tbl_t));	\
+		else						\
+			rtw89_rfk_parser(_dev, (tbl_f));	\
+	} while (0)
+
+static u8 _kpath(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[RFK]dbcc_en: %x,  PHY%d\n",
+		    rtwdev->dbcc_en, phy_idx);
+
+	if (!rtwdev->dbcc_en)
+		return RF_AB;
+
+	if (phy_idx == RTW89_PHY_0)
+		return RF_A;
+	else
+		return RF_B;
+}
+
+static const u32 rtw8852a_backup_bb_regs[] = {0x2344, 0x58f0, 0x78f0};
+static const u32 rtw8852a_backup_rf_regs[] = {0xef, 0xde, 0x0, 0x1e, 0x2, 0x85, 0x90, 0x5};
+#define BACKUP_BB_REGS_NR ARRAY_SIZE(rtw8852a_backup_bb_regs)
+#define BACKUP_RF_REGS_NR ARRAY_SIZE(rtw8852a_backup_rf_regs)
+
+static void _rfk_backup_bb_reg(struct rtw89_dev *rtwdev, u32 backup_bb_reg_val[])
+{
+	u32 i;
+
+	for (i = 0; i < BACKUP_BB_REGS_NR; i++) {
+		backup_bb_reg_val[i] =
+			rtw89_phy_read32_mask(rtwdev, rtw8852a_backup_bb_regs[i],
+					      MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[IQK]backup bb reg : %x, value =%x\n",
+			    rtw8852a_backup_bb_regs[i], backup_bb_reg_val[i]);
+	}
+}
+
+static void _rfk_backup_rf_reg(struct rtw89_dev *rtwdev, u32 backup_rf_reg_val[],
+			       u8 rf_path)
+{
+	u32 i;
+
+	for (i = 0; i < BACKUP_RF_REGS_NR; i++) {
+		backup_rf_reg_val[i] =
+			rtw89_read_rf(rtwdev, rf_path,
+				      rtw8852a_backup_rf_regs[i], RFREG_MASK);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[IQK]backup rf S%d reg : %x, value =%x\n", rf_path,
+			    rtw8852a_backup_rf_regs[i], backup_rf_reg_val[i]);
+	}
+}
+
+static void _rfk_restore_bb_reg(struct rtw89_dev *rtwdev,
+				u32 backup_bb_reg_val[])
+{
+	u32 i;
+
+	for (i = 0; i < BACKUP_BB_REGS_NR; i++) {
+		rtw89_phy_write32_mask(rtwdev, rtw8852a_backup_bb_regs[i],
+				       MASKDWORD, backup_bb_reg_val[i]);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[IQK]restore bb reg : %x, value =%x\n",
+			    rtw8852a_backup_bb_regs[i], backup_bb_reg_val[i]);
+	}
+}
+
+static void _rfk_restore_rf_reg(struct rtw89_dev *rtwdev,
+				u32 backup_rf_reg_val[], u8 rf_path)
+{
+	u32 i;
+
+	for (i = 0; i < BACKUP_RF_REGS_NR; i++) {
+		rtw89_write_rf(rtwdev, rf_path, rtw8852a_backup_rf_regs[i],
+			       RFREG_MASK, backup_rf_reg_val[i]);
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[IQK]restore rf S%d reg: %x, value =%x\n", rf_path,
+			    rtw8852a_backup_rf_regs[i], backup_rf_reg_val[i]);
+	}
+}
+
+static void _wait_rx_mode(struct rtw89_dev *rtwdev, u8 kpath)
+{
+	u8 path;
+	u32 rf_mode;
+	int ret;
+
+	for (path = 0; path < RF_PATH_MAX; path++) {
+		if (!(kpath & BIT(path)))
+			continue;
+
+		ret = read_poll_timeout_atomic(rtw89_read_rf, rf_mode, rf_mode != 2,
+					       2, 5000, false, rtwdev, path, 0x00,
+					       RR_MOD_MASK);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[RFK] Wait S%d to Rx mode!! (ret = %d)\n",
+			    path, ret);
+	}
+}
+
+static void _dack_dump(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u8 i;
+	u8 t;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S0 ADC_DCK ic = 0x%x, qc = 0x%x\n",
+		    dack->addck_d[0][0], dack->addck_d[0][1]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S1 ADC_DCK ic = 0x%x, qc = 0x%x\n",
+		    dack->addck_d[1][0], dack->addck_d[1][1]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S0 DAC_DCK ic = 0x%x, qc = 0x%x\n",
+		    dack->dadck_d[0][0], dack->dadck_d[0][1]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S1 DAC_DCK ic = 0x%x, qc = 0x%x\n",
+		    dack->dadck_d[1][0], dack->dadck_d[1][1]);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S0 biask ic = 0x%x, qc = 0x%x\n",
+		    dack->biask_d[0][0], dack->biask_d[0][1]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S1 biask ic = 0x%x, qc = 0x%x\n",
+		    dack->biask_d[1][0], dack->biask_d[1][1]);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S0 MSBK ic:\n");
+	for (i = 0; i < RTW89_DACK_MSBK_NR; i++) {
+		t = dack->msbk_d[0][0][i];
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x\n", t);
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S0 MSBK qc:\n");
+	for (i = 0; i < RTW89_DACK_MSBK_NR; i++) {
+		t = dack->msbk_d[0][1][i];
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x\n", t);
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S1 MSBK ic:\n");
+	for (i = 0; i < RTW89_DACK_MSBK_NR; i++) {
+		t = dack->msbk_d[1][0][i];
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x\n", t);
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S1 MSBK qc:\n");
+	for (i = 0; i < RTW89_DACK_MSBK_NR; i++) {
+		t = dack->msbk_d[1][1][i];
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x\n", t);
+	}
+}
+
+static void _afe_init(struct rtw89_dev *rtwdev)
+{
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_afe_init_defs_tbl);
+}
+
+static void _addck_backup(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+
+	rtw89_phy_write32_clr(rtwdev, R_S0_RXDC2, B_S0_RXDC2_SEL);
+	dack->addck_d[0][0] = (u16)rtw89_phy_read32_mask(rtwdev, R_S0_ADDCK,
+							 B_S0_ADDCK_Q);
+	dack->addck_d[0][1] = (u16)rtw89_phy_read32_mask(rtwdev, R_S0_ADDCK,
+							 B_S0_ADDCK_I);
+
+	rtw89_phy_write32_clr(rtwdev, R_S1_RXDC2, B_S1_RXDC2_SEL);
+	dack->addck_d[1][0] = (u16)rtw89_phy_read32_mask(rtwdev, R_S1_ADDCK,
+							 B_S1_ADDCK_Q);
+	dack->addck_d[1][1] = (u16)rtw89_phy_read32_mask(rtwdev, R_S1_ADDCK,
+							 B_S1_ADDCK_I);
+}
+
+static void _addck_reload(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+
+	rtw89_phy_write32_mask(rtwdev, R_S0_RXDC, B_S0_RXDC_I, dack->addck_d[0][0]);
+	rtw89_phy_write32_mask(rtwdev, R_S0_RXDC2, B_S0_RXDC2_Q2,
+			       (dack->addck_d[0][1] >> 6));
+	rtw89_phy_write32_mask(rtwdev, R_S0_RXDC, B_S0_RXDC_Q,
+			       (dack->addck_d[0][1] & 0x3f));
+	rtw89_phy_write32_set(rtwdev, R_S0_RXDC2, B_S0_RXDC2_MEN);
+	rtw89_phy_write32_mask(rtwdev, R_S1_RXDC, B_S1_RXDC_I, dack->addck_d[1][0]);
+	rtw89_phy_write32_mask(rtwdev, R_S1_RXDC2, B_S1_RXDC2_Q2,
+			       (dack->addck_d[1][1] >> 6));
+	rtw89_phy_write32_mask(rtwdev, R_S1_RXDC, B_S1_RXDC_Q,
+			       (dack->addck_d[1][1] & 0x3f));
+	rtw89_phy_write32_set(rtwdev, R_S1_RXDC2, B_S1_RXDC2_EN);
+}
+
+static void _dack_backup_s0(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u8 i;
+
+	rtw89_phy_write32_set(rtwdev, R_S0_DACKI, B_S0_DACKI_EN);
+	rtw89_phy_write32_set(rtwdev, R_S0_DACKQ, B_S0_DACKQ_EN);
+	rtw89_phy_write32_set(rtwdev, R_P0_NRBW, B_P0_NRBW_DBG);
+
+	for (i = 0; i < RTW89_DACK_MSBK_NR; i++) {
+		rtw89_phy_write32_mask(rtwdev, R_S0_DACKI, B_S0_DACKI_AR, i);
+		dack->msbk_d[0][0][i] =
+			(u8)rtw89_phy_read32_mask(rtwdev, R_S0_DACKI7, B_S0_DACKI7_K);
+		rtw89_phy_write32_mask(rtwdev, R_S0_DACKQ, B_S0_DACKQ_AR, i);
+		dack->msbk_d[0][1][i] =
+			(u8)rtw89_phy_read32_mask(rtwdev, R_S0_DACKQ7, B_S0_DACKQ7_K);
+	}
+	dack->biask_d[0][0] = (u16)rtw89_phy_read32_mask(rtwdev, R_S0_DACKI2,
+							 B_S0_DACKI2_K);
+	dack->biask_d[0][1] = (u16)rtw89_phy_read32_mask(rtwdev, R_S0_DACKQ2,
+							 B_S0_DACKQ2_K);
+	dack->dadck_d[0][0] = (u8)rtw89_phy_read32_mask(rtwdev, R_S0_DACKI8,
+							B_S0_DACKI8_K) - 8;
+	dack->dadck_d[0][1] = (u8)rtw89_phy_read32_mask(rtwdev, R_S0_DACKQ8,
+							B_S0_DACKQ8_K) - 8;
+}
+
+static void _dack_backup_s1(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u8 i;
+
+	rtw89_phy_write32_set(rtwdev, R_S1_DACKI, B_S1_DACKI_EN);
+	rtw89_phy_write32_set(rtwdev, R_S1_DACKQ, B_S1_DACKQ_EN);
+	rtw89_phy_write32_set(rtwdev, R_P1_DBGMOD, B_P1_DBGMOD_ON);
+
+	for (i = 0; i < RTW89_DACK_MSBK_NR; i++) {
+		rtw89_phy_write32_mask(rtwdev, R_S1_DACKI, B_S1_DACKI_AR, i);
+		dack->msbk_d[1][0][i] =
+			(u8)rtw89_phy_read32_mask(rtwdev, R_S1_DACKI7, B_S1_DACKI_K);
+		rtw89_phy_write32_mask(rtwdev, R_S1_DACKQ, B_S1_DACKQ_AR, i);
+		dack->msbk_d[1][1][i] =
+			(u8)rtw89_phy_read32_mask(rtwdev, R_S1_DACKQ7, B_S1_DACKQ7_K);
+	}
+	dack->biask_d[1][0] =
+		(u16)rtw89_phy_read32_mask(rtwdev, R_S1_DACKI2, B_S1_DACKI2_K);
+	dack->biask_d[1][1] =
+		(u16)rtw89_phy_read32_mask(rtwdev, R_S1_DACKQ2, B_S1_DACKQ2_K);
+	dack->dadck_d[1][0] =
+		(u8)rtw89_phy_read32_mask(rtwdev, R_S1_DACKI8, B_S1_DACKI8_K) - 8;
+	dack->dadck_d[1][1] =
+		(u8)rtw89_phy_read32_mask(rtwdev, R_S1_DACKQ8, B_S1_DACKQ8_K) - 8;
+}
+
+static void _dack_reload_by_path(struct rtw89_dev *rtwdev,
+				 enum rtw89_rf_path path, u8 index)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u32 tmp = 0, tmp_offset, tmp_reg;
+	u8 i;
+	u32 idx_offset, path_offset;
+
+	if (index == 0)
+		idx_offset = 0;
+	else
+		idx_offset = 0x50;
+
+	if (path == RF_PATH_A)
+		path_offset = 0;
+	else
+		path_offset = 0x2000;
+
+	tmp_offset = idx_offset + path_offset;
+	/* msbk_d: 15/14/13/12 */
+	tmp = 0x0;
+	for (i = 0; i < RTW89_DACK_MSBK_NR / 4; i++)
+		tmp |= dack->msbk_d[path][index][i + 12] << (i * 8);
+	tmp_reg = 0x5e14 + tmp_offset;
+	rtw89_phy_write32(rtwdev, tmp_reg, tmp);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x=0x%x\n", tmp_reg,
+		    rtw89_phy_read32_mask(rtwdev, tmp_reg, MASKDWORD));
+	/* msbk_d: 11/10/9/8 */
+	tmp = 0x0;
+	for (i = 0; i < RTW89_DACK_MSBK_NR / 4; i++)
+		tmp |= dack->msbk_d[path][index][i + 8] << (i * 8);
+	tmp_reg = 0x5e18 + tmp_offset;
+	rtw89_phy_write32(rtwdev, tmp_reg, tmp);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x=0x%x\n", tmp_reg,
+		    rtw89_phy_read32_mask(rtwdev, tmp_reg, MASKDWORD));
+	/* msbk_d: 7/6/5/4 */
+	tmp = 0x0;
+	for (i = 0; i < RTW89_DACK_MSBK_NR / 4; i++)
+		tmp |= dack->msbk_d[path][index][i + 4] << (i * 8);
+	tmp_reg = 0x5e1c + tmp_offset;
+	rtw89_phy_write32(rtwdev, tmp_reg, tmp);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x=0x%x\n", tmp_reg,
+		    rtw89_phy_read32_mask(rtwdev, tmp_reg, MASKDWORD));
+	/* msbk_d: 3/2/1/0 */
+	tmp = 0x0;
+	for (i = 0; i < RTW89_DACK_MSBK_NR / 4; i++)
+		tmp |= dack->msbk_d[path][index][i] << (i * 8);
+	tmp_reg = 0x5e20 + tmp_offset;
+	rtw89_phy_write32(rtwdev, tmp_reg, tmp);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]0x%x=0x%x\n", tmp_reg,
+		    rtw89_phy_read32_mask(rtwdev, tmp_reg, MASKDWORD));
+	/* dadak_d/biask_d */
+	tmp = 0x0;
+	tmp = (dack->biask_d[path][index] << 22) |
+	       (dack->dadck_d[path][index] << 14);
+	tmp_reg = 0x5e24 + tmp_offset;
+	rtw89_phy_write32(rtwdev, tmp_reg, tmp);
+}
+
+static void _dack_reload(struct rtw89_dev *rtwdev, enum rtw89_rf_path path)
+{
+	u8 i;
+
+	for (i = 0; i < 2; i++)
+		_dack_reload_by_path(rtwdev, path, i);
+
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_rfk_dack_reload_defs_a_tbl,
+				 &rtw8852a_rfk_dack_reload_defs_b_tbl);
+}
+
+#define ADDC_T_AVG 100
+static void _check_addc(struct rtw89_dev *rtwdev, enum rtw89_rf_path path)
+{
+	s32 dc_re = 0, dc_im = 0;
+	u32 tmp;
+	u32 i;
+
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_rfk_check_addc_defs_a_tbl,
+				 &rtw8852a_rfk_check_addc_defs_b_tbl);
+
+	for (i = 0; i < ADDC_T_AVG; i++) {
+		tmp = rtw89_phy_read32_mask(rtwdev, R_DBG32_D, MASKDWORD);
+		dc_re += sign_extend32(FIELD_GET(0xfff000, tmp), 11);
+		dc_im += sign_extend32(FIELD_GET(0xfff, tmp), 11);
+	}
+
+	dc_re /= ADDC_T_AVG;
+	dc_im /= ADDC_T_AVG;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DACK]S%d,dc_re = 0x%x,dc_im =0x%x\n", path, dc_re, dc_im);
+}
+
+static void _addck(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u32 val;
+	int ret;
+
+	/* S0 */
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_addck_reset_defs_a_tbl);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]before S0 ADDCK\n");
+	_check_addc(rtwdev, RF_PATH_A);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_addck_trigger_defs_a_tbl);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+				       false, rtwdev, 0x1e00, BIT(0));
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S0 ADDCK timeout\n");
+		dack->addck_timeout[0] = true;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]ADDCK ret = %d\n", ret);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]after S0 ADDCK\n");
+	_check_addc(rtwdev, RF_PATH_A);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_addck_restore_defs_a_tbl);
+
+	/* S1 */
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_addck_reset_defs_b_tbl);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]before S1 ADDCK\n");
+	_check_addc(rtwdev, RF_PATH_B);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_addck_trigger_defs_b_tbl);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+				       false, rtwdev, 0x3e00, BIT(0));
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S1 ADDCK timeout\n");
+		dack->addck_timeout[1] = true;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]ADDCK ret = %d\n", ret);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]after S1 ADDCK\n");
+	_check_addc(rtwdev, RF_PATH_B);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_addck_restore_defs_b_tbl);
+}
+
+static void _check_dadc(struct rtw89_dev *rtwdev, enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_rfk_check_dadc_defs_f_a_tbl,
+				 &rtw8852a_rfk_check_dadc_defs_f_b_tbl);
+
+	_check_addc(rtwdev, path);
+
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_rfk_check_dadc_defs_r_a_tbl,
+				 &rtw8852a_rfk_check_dadc_defs_r_b_tbl);
+}
+
+static void _dack_s0(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u32 val;
+	int ret;
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dack_defs_f_a_tbl);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+				       false, rtwdev, 0x5e28, BIT(15));
+	ret |= read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+					false, rtwdev, 0x5e78, BIT(15));
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S0 MSBK timeout\n");
+		dack->msbk_timeout[0] = true;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK ret = %d\n", ret);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dack_defs_m_a_tbl);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+				       false, rtwdev, 0x5e48, BIT(17));
+	ret |= read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+					false, rtwdev, 0x5e98, BIT(17));
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S0 DADACK timeout\n");
+		dack->dadck_timeout[0] = true;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK ret = %d\n", ret);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dack_defs_r_a_tbl);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]after S0 DADCK\n");
+	_check_dadc(rtwdev, RF_PATH_A);
+
+	_dack_backup_s0(rtwdev);
+	_dack_reload(rtwdev, RF_PATH_A);
+
+	rtw89_phy_write32_clr(rtwdev, R_P0_NRBW, B_P0_NRBW_DBG);
+}
+
+static void _dack_s1(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u32 val;
+	int ret;
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dack_defs_f_b_tbl);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+				       false, rtwdev, 0x7e28, BIT(15));
+	ret |= read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+					false, rtwdev, 0x7e78, BIT(15));
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S1 MSBK timeout\n");
+		dack->msbk_timeout[1] = true;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK ret = %d\n", ret);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dack_defs_m_b_tbl);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+				       false, rtwdev, 0x7e48, BIT(17));
+	ret |= read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val, 1, 10000,
+					false, rtwdev, 0x7e98, BIT(17));
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]S1 DADCK timeout\n");
+		dack->dadck_timeout[1] = true;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK ret = %d\n", ret);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dack_defs_r_b_tbl);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]after S1 DADCK\n");
+	_check_dadc(rtwdev, RF_PATH_B);
+
+	_dack_backup_s1(rtwdev);
+	_dack_reload(rtwdev, RF_PATH_B);
+
+	rtw89_phy_write32_clr(rtwdev, R_P1_DBGMOD, B_P1_DBGMOD_ON);
+}
+
+static void _dack(struct rtw89_dev *rtwdev)
+{
+	_dack_s0(rtwdev);
+	_dack_s1(rtwdev);
+}
+
+static void _dac_cal(struct rtw89_dev *rtwdev, bool force)
+{
+	struct rtw89_dack_info *dack = &rtwdev->dack;
+	u32 rf0_0, rf1_0;
+	u8 phy_map = rtw89_btc_phymap(rtwdev, RTW89_PHY_0, RF_AB);
+
+	dack->dack_done = false;
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK b\n");
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK start!!!\n");
+	rf0_0 = rtw89_read_rf(rtwdev, RF_PATH_A, RR_MOD, RFREG_MASK);
+	rf1_0 = rtw89_read_rf(rtwdev, RF_PATH_B, RR_MOD, RFREG_MASK);
+	_afe_init(rtwdev);
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_RSV1, RR_RSV1_RST, 0x0);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_RSV1, RR_RSV1_RST, 0x0);
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_MOD, RFREG_MASK, 0x30001);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_MOD, RFREG_MASK, 0x30001);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DACK, BTC_WRFK_ONESHOT_START);
+	_addck(rtwdev);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DACK, BTC_WRFK_ONESHOT_STOP);
+	_addck_backup(rtwdev);
+	_addck_reload(rtwdev);
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_MOD, RFREG_MASK, 0x40001);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_MOD, RFREG_MASK, 0x40001);
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_MODOPT, RFREG_MASK, 0x0);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_MODOPT, RFREG_MASK, 0x0);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DACK, BTC_WRFK_ONESHOT_START);
+	_dack(rtwdev);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DACK, BTC_WRFK_ONESHOT_STOP);
+	_dack_dump(rtwdev);
+	dack->dack_done = true;
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_MOD, RFREG_MASK, rf0_0);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_MOD, RFREG_MASK, rf1_0);
+	rtw89_write_rf(rtwdev, RF_PATH_A, RR_RSV1, RR_RSV1_RST, 0x1);
+	rtw89_write_rf(rtwdev, RF_PATH_B, RR_RSV1, RR_RSV1_RST, 0x1);
+	dack->dack_cnt++;
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DACK]DACK finish!!!\n");
+}
+
+#define RTW8852A_NCTL_VER 0xd
+#define RTW8852A_IQK_VER 0x2a
+#define RTW8852A_IQK_SS 2
+#define RTW8852A_IQK_THR_REK 8
+#define RTW8852A_IQK_CFIR_GROUP_NR 4
+
+enum rtw8852a_iqk_type {
+	ID_TXAGC,
+	ID_FLOK_COARSE,
+	ID_FLOK_FINE,
+	ID_TXK,
+	ID_RXAGC,
+	ID_RXK,
+	ID_NBTXK,
+	ID_NBRXK,
+};
+
+static void _iqk_read_fft_dbcc0(struct rtw89_dev *rtwdev, u8 path)
+{
+	u8 i = 0x0;
+	u32 fft[6] = {0x0};
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x00160000);
+	fft[0] = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x00170000);
+	fft[1] = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x00180000);
+	fft[2] = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x00190000);
+	fft[3] = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x001a0000);
+	fft[4] = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x001b0000);
+	fft[5] = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD);
+	for (i = 0; i < 6; i++)
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x,fft[%x]= %x\n",
+			    path, i, fft[i]);
+}
+
+static void _iqk_read_xym_dbcc0(struct rtw89_dev *rtwdev, u8 path)
+{
+	u8 i = 0x0;
+	u32 tmp = 0x0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_CFG, B_NCTL_CFG_SPAGE, path);
+	rtw89_phy_write32_mask(rtwdev, R_IQK_DIF, B_IQK_DIF_TRX, 0x1);
+
+	for (i = 0x0; i < 0x18; i++) {
+		rtw89_phy_write32_mask(rtwdev, R_NCTL_N2, MASKDWORD, 0x000000c0 + i);
+		rtw89_phy_write32_clr(rtwdev, R_NCTL_N2, MASKDWORD);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, 0x8%lx38 = %x\n",
+			    path, BIT(path), tmp);
+		udelay(1);
+	}
+	rtw89_phy_write32_clr(rtwdev, R_IQK_DIF, B_IQK_DIF_TRX);
+	rtw89_phy_write32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD, 0x40000000);
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_N2, MASKDWORD, 0x80010100);
+	udelay(1);
+}
+
+static void _iqk_read_txcfir_dbcc0(struct rtw89_dev *rtwdev, u8 path,
+				   u8 group)
+{
+	static const u32 base_addrs[RTW8852A_IQK_SS][RTW8852A_IQK_CFIR_GROUP_NR] = {
+		{0x8f20, 0x8f54, 0x8f88, 0x8fbc},
+		{0x9320, 0x9354, 0x9388, 0x93bc},
+	};
+	u8 idx = 0x0;
+	u32 tmp = 0x0;
+	u32 base_addr;
+
+	if (path >= RTW8852A_IQK_SS) {
+		rtw89_warn(rtwdev, "cfir path %d out of range\n", path);
+		return;
+	}
+	if (group >= RTW8852A_IQK_CFIR_GROUP_NR) {
+		rtw89_warn(rtwdev, "cfir group %d out of range\n", group);
+		return;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	rtw89_phy_write32_mask(rtwdev, R_W_COEF + (path << 8), MASKDWORD, 0x00000001);
+
+	base_addr = base_addrs[path][group];
+
+	for (idx = 0; idx < 0x0d; idx++) {
+		tmp = rtw89_phy_read32_mask(rtwdev, base_addr + (idx << 2), MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[IQK] %x = %x\n",
+			    base_addr + (idx << 2), tmp);
+	}
+
+	if (path == 0x0) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]\n");
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P0C0, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8f50 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P0C1, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8f84 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P0C2, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8fb8 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P0C3, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8fec = %x\n", tmp);
+	} else {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]\n");
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P1C0, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x9350 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P1C1, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x9384 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P1C2, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x93b8 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXCFIR_P1C3, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x93ec = %x\n", tmp);
+	}
+	rtw89_phy_write32_clr(rtwdev, R_W_COEF + (path << 8), MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT + (path << 8), B_KIP_RPT_SEL, 0xc);
+	udelay(1);
+	tmp = rtw89_phy_read32_mask(rtwdev, R_RPT_PER + (path << 8), MASKDWORD);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, 0x8%lxfc = %x\n", path,
+		    BIT(path), tmp);
+}
+
+static void _iqk_read_rxcfir_dbcc0(struct rtw89_dev *rtwdev, u8 path,
+				   u8 group)
+{
+	static const u32 base_addrs[RTW8852A_IQK_SS][RTW8852A_IQK_CFIR_GROUP_NR] = {
+		{0x8d00, 0x8d44, 0x8d88, 0x8dcc},
+		{0x9100, 0x9144, 0x9188, 0x91cc},
+	};
+	u8 idx = 0x0;
+	u32 tmp = 0x0;
+	u32 base_addr;
+
+	if (path >= RTW8852A_IQK_SS) {
+		rtw89_warn(rtwdev, "cfir path %d out of range\n", path);
+		return;
+	}
+	if (group >= RTW8852A_IQK_CFIR_GROUP_NR) {
+		rtw89_warn(rtwdev, "cfir group %d out of range\n", group);
+		return;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	rtw89_phy_write32_mask(rtwdev, R_W_COEF + (path << 8), MASKDWORD, 0x00000001);
+
+	base_addr = base_addrs[path][group];
+	for (idx = 0; idx < 0x10; idx++) {
+		tmp = rtw89_phy_read32_mask(rtwdev, base_addr + (idx << 2), MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[IQK]%x = %x\n",
+			    base_addr + (idx << 2), tmp);
+	}
+
+	if (path == 0x0) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]\n");
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P0C0, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8d40 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P0C1, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8d84 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P0C2, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8dc8 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P0C3, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x8e0c = %x\n", tmp);
+	} else {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]\n");
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P1C0, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x9140 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P1C1, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x9184 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P1C2, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x91c8 = %x\n", tmp);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXCFIR_P1C3, MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK] 0x920c = %x\n", tmp);
+	}
+	rtw89_phy_write32_clr(rtwdev, R_W_COEF + (path << 8), MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT + (path << 8), B_KIP_RPT_SEL, 0xd);
+	tmp = rtw89_phy_read32_mask(rtwdev, R_RPT_PER + (path << 8), MASKDWORD);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, 0x8%lxfc = %x\n", path,
+		    BIT(path), tmp);
+}
+
+static void _iqk_sram(struct rtw89_dev *rtwdev, u8 path)
+{
+	u32 tmp = 0x0;
+	u32 i = 0x0;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, MASKDWORD, 0x00020000);
+	rtw89_phy_write32_mask(rtwdev, R_SRAM_IQRX2, MASKDWORD, 0x00000080);
+	rtw89_phy_write32_mask(rtwdev, R_SRAM_IQRX, MASKDWORD, 0x00010000);
+	rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_TXT, 0x009);
+
+	for (i = 0; i <= 0x9f; i++) {
+		rtw89_phy_write32_mask(rtwdev, R_SRAM_IQRX, MASKDWORD, 0x00010000 + i);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_DCI);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]0x%x\n", tmp);
+	}
+
+	for (i = 0; i <= 0x9f; i++) {
+		rtw89_phy_write32_mask(rtwdev, R_SRAM_IQRX, MASKDWORD, 0x00010000 + i);
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_DCQ);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]0x%x\n", tmp);
+	}
+	rtw89_phy_write32_clr(rtwdev, R_SRAM_IQRX2, MASKDWORD);
+	rtw89_phy_write32_clr(rtwdev, R_SRAM_IQRX, MASKDWORD);
+}
+
+static void _iqk_rxk_setting(struct rtw89_dev *rtwdev, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u32 tmp = 0x0;
+
+	rtw89_phy_write32_set(rtwdev, R_P0_NRBW + (path << 13), B_P0_NRBW_DBG);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR_PW15, B_ANAPAR_PW15, 0x3);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR, B_ANAPAR_15, 0xa041);
+	udelay(1);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR_PW15, B_ANAPAR_PW15_H2, 0x3);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR, B_ANAPAR_FLTRST, 0x0);
+	udelay(1);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR, B_ANAPAR_FLTRST, 0x1);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR_PW15, B_ANAPAR_PW15_H2, 0x0);
+	udelay(1);
+	rtw89_phy_write32_mask(rtwdev, R_ADC_FIFO, B_ADC_FIFO_RST, 0x0303);
+	rtw89_phy_write32_mask(rtwdev, R_ADC_FIFO, B_ADC_FIFO_RST, 0x0000);
+
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_RXK2);
+		rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_SEL2G, 0x1);
+		break;
+	case RTW89_BAND_5G:
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_RXK2);
+		rtw89_write_rf(rtwdev, path, RR_WLSEL, RR_WLSEL_AG, 0x5);
+		rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_SEL5G, 0x1);
+		break;
+	default:
+		break;
+	}
+	tmp = rtw89_read_rf(rtwdev, path, RR_CFGCH, RFREG_MASK);
+	rtw89_write_rf(rtwdev, path, RR_RSV4, RFREG_MASK, tmp);
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_OFF, 0x13);
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x1);
+	fsleep(128);
+}
+
+static bool _iqk_check_cal(struct rtw89_dev *rtwdev, u8 path, u8 ktype)
+{
+	u32 tmp;
+	u32 val;
+	int ret;
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val == 0x55, 1, 8200,
+				       false, rtwdev, 0xbff8, MASKBYTE0);
+	if (ret)
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]IQK timeout!!!\n");
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, MASKBYTE0);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, ret=%d\n", path, ret);
+	tmp = rtw89_phy_read32_mask(rtwdev, R_NCTL_RPT, MASKDWORD);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[IQK]S%x, type= %x, 0x8008 = 0x%x\n", path, ktype, tmp);
+
+	return false;
+}
+
+static bool _iqk_one_shot(struct rtw89_dev *rtwdev,
+			  enum rtw89_phy_idx phy_idx, u8 path, u8 ktype)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	bool fail = false;
+	u32 iqk_cmd = 0x0;
+	u8 phy_map = rtw89_btc_path_phymap(rtwdev, phy_idx, path);
+	u32 addr_rfc_ctl = 0x0;
+
+	if (path == RF_PATH_A)
+		addr_rfc_ctl = 0x5864;
+	else
+		addr_rfc_ctl = 0x7864;
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_IQK, BTC_WRFK_ONESHOT_START);
+	switch (ktype) {
+	case ID_TXAGC:
+		iqk_cmd = 0x008 | (1 << (4 + path)) | (path << 1);
+		break;
+	case ID_FLOK_COARSE:
+		rtw89_phy_write32_set(rtwdev, addr_rfc_ctl, 0x20000000);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_TXT, 0x009);
+		iqk_cmd = 0x108 | (1 << (4 + path));
+		break;
+	case ID_FLOK_FINE:
+		rtw89_phy_write32_set(rtwdev, addr_rfc_ctl, 0x20000000);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_TXT, 0x009);
+		iqk_cmd = 0x208 | (1 << (4 + path));
+		break;
+	case ID_TXK:
+		rtw89_phy_write32_clr(rtwdev, addr_rfc_ctl, 0x20000000);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_TXT, 0x025);
+		iqk_cmd = 0x008 | (1 << (path + 4)) |
+			  (((0x8 + iqk_info->iqk_bw[path]) & 0xf) << 8);
+		break;
+	case ID_RXAGC:
+		iqk_cmd = 0x508 | (1 << (4 + path)) | (path << 1);
+		break;
+	case ID_RXK:
+		rtw89_phy_write32_set(rtwdev, addr_rfc_ctl, 0x20000000);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_RXT, 0x011);
+		iqk_cmd = 0x008 | (1 << (path + 4)) |
+			  (((0xb + iqk_info->iqk_bw[path]) & 0xf) << 8);
+		break;
+	case ID_NBTXK:
+		rtw89_phy_write32_clr(rtwdev, addr_rfc_ctl, 0x20000000);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_TXT, 0x025);
+		iqk_cmd = 0x308 | (1 << (4 + path));
+		break;
+	case ID_NBRXK:
+		rtw89_phy_write32_set(rtwdev, addr_rfc_ctl, 0x20000000);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_RXT, 0x011);
+		iqk_cmd = 0x608 | (1 << (4 + path));
+		break;
+	default:
+		return false;
+	}
+
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_CFG, MASKDWORD, iqk_cmd + 1);
+	rtw89_phy_write32_set(rtwdev, R_DPK_CTL, B_DPK_CTL_EN);
+	udelay(1);
+	fail = _iqk_check_cal(rtwdev, path, ktype);
+	if (iqk_info->iqk_xym_en)
+		_iqk_read_xym_dbcc0(rtwdev, path);
+	if (iqk_info->iqk_fft_en)
+		_iqk_read_fft_dbcc0(rtwdev, path);
+	if (iqk_info->iqk_sram_en)
+		_iqk_sram(rtwdev, path);
+	if (iqk_info->iqk_cfir_en) {
+		if (ktype == ID_TXK) {
+			_iqk_read_txcfir_dbcc0(rtwdev, path, 0x0);
+			_iqk_read_txcfir_dbcc0(rtwdev, path, 0x1);
+			_iqk_read_txcfir_dbcc0(rtwdev, path, 0x2);
+			_iqk_read_txcfir_dbcc0(rtwdev, path, 0x3);
+		} else {
+			_iqk_read_rxcfir_dbcc0(rtwdev, path, 0x0);
+			_iqk_read_rxcfir_dbcc0(rtwdev, path, 0x1);
+			_iqk_read_rxcfir_dbcc0(rtwdev, path, 0x2);
+			_iqk_read_rxcfir_dbcc0(rtwdev, path, 0x3);
+		}
+	}
+
+	rtw89_phy_write32_clr(rtwdev, addr_rfc_ctl, 0x20000000);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_IQK, BTC_WRFK_ONESHOT_STOP);
+
+	return fail;
+}
+
+static bool _rxk_group_sel(struct rtw89_dev *rtwdev,
+			   enum rtw89_phy_idx phy_idx, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	static const u32 rxgn_a[4] = {0x18C, 0x1A0, 0x28C, 0x2A0};
+	static const u32 attc2_a[4] = {0x0, 0x0, 0x07, 0x30};
+	static const u32 attc1_a[4] = {0x7, 0x5, 0x1, 0x1};
+	static const u32 rxgn_g[4] = {0x1CC, 0x1E0, 0x2CC, 0x2E0};
+	static const u32 attc2_g[4] = {0x0, 0x15, 0x3, 0x1a};
+	static const u32 attc1_g[4] = {0x1, 0x0, 0x1, 0x0};
+	u8 gp = 0x0;
+	bool fail = false;
+	u32 rf0 = 0x0;
+
+	for (gp = 0; gp < 0x4; gp++) {
+		switch (iqk_info->iqk_band[path]) {
+		case RTW89_BAND_2G:
+			rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXG, rxgn_g[gp]);
+			rtw89_write_rf(rtwdev, path, RR_RXBB, RR_RXBB_C2G, attc2_g[gp]);
+			rtw89_write_rf(rtwdev, path, RR_RXBB, RR_RXBB_C1G, attc1_g[gp]);
+			break;
+		case RTW89_BAND_5G:
+			rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXG, rxgn_a[gp]);
+			rtw89_write_rf(rtwdev, path, RR_RXA2, RR_RXA2_C2, attc2_a[gp]);
+			rtw89_write_rf(rtwdev, path, RR_RXA2, RR_RXA2_C1, attc1_a[gp]);
+			break;
+		default:
+			break;
+		}
+		rtw89_phy_write32_set(rtwdev, R_IQK_CFG, B_IQK_CFG_SET);
+		rf0 = rtw89_read_rf(rtwdev, path, RR_MOD, RFREG_MASK);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_DIF2, B_IQK_DIF2_RXPI,
+				       rf0 | iqk_info->syn1to2);
+		rtw89_phy_write32_mask(rtwdev, R_IQK_COM, MASKDWORD, 0x40010100);
+		rtw89_phy_write32_clr(rtwdev, R_IQK_RES + (path << 8), B_IQK_RES_RXCFIR);
+		rtw89_phy_write32_set(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_SEL);
+		rtw89_phy_write32_clr(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_G3);
+		rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_GP, gp);
+		rtw89_phy_write32_mask(rtwdev, R_IOQ_IQK_DPK, B_IOQ_IQK_DPK_EN, 0x1);
+		rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, B_NCTL_N1_CIP);
+		fail = _iqk_one_shot(rtwdev, phy_idx, path, ID_RXK);
+		rtw89_phy_write32_mask(rtwdev, R_IQKINF, BIT(16 + gp + path * 4), fail);
+	}
+
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_SEL2G, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0);
+		break;
+	case RTW89_BAND_5G:
+		rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_SEL5G, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_WLSEL, RR_WLSEL_AG, 0x0);
+		break;
+	default:
+		break;
+	}
+	iqk_info->nb_rxcfir[path] = 0x40000000;
+	rtw89_phy_write32_mask(rtwdev, R_IQK_RES + (path << 8),
+			       B_IQK_RES_RXCFIR, 0x5);
+	iqk_info->is_wb_rxiqk[path] = true;
+	return false;
+}
+
+static bool _iqk_nbrxk(struct rtw89_dev *rtwdev,
+		       enum rtw89_phy_idx phy_idx, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u8 group = 0x0;
+	u32 rf0 = 0x0, tmp = 0x0;
+	u32 idxrxgain_a = 0x1a0;
+	u32 idxattc2_a = 0x00;
+	u32 idxattc1_a = 0x5;
+	u32 idxrxgain_g = 0x1E0;
+	u32 idxattc2_g = 0x15;
+	u32 idxattc1_g = 0x0;
+	bool fail = false;
+
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXG, idxrxgain_g);
+		rtw89_write_rf(rtwdev, path, RR_RXBB, RR_RXBB_C2G, idxattc2_g);
+		rtw89_write_rf(rtwdev, path, RR_RXBB, RR_RXBB_C1G, idxattc1_g);
+		break;
+	case RTW89_BAND_5G:
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXG, idxrxgain_a);
+		rtw89_write_rf(rtwdev, path, RR_RXA2, RR_RXA2_C2, idxattc2_a);
+		rtw89_write_rf(rtwdev, path, RR_RXA2, RR_RXA2_C1, idxattc1_a);
+		break;
+	default:
+		break;
+	}
+	rtw89_phy_write32_set(rtwdev, R_IQK_CFG, B_IQK_CFG_SET);
+	rf0 = rtw89_read_rf(rtwdev, path, RR_MOD, RFREG_MASK);
+	rtw89_phy_write32_mask(rtwdev, R_IQK_DIF2, B_IQK_DIF2_RXPI,
+			       rf0 | iqk_info->syn1to2);
+	rtw89_phy_write32_mask(rtwdev, R_IQK_COM, MASKDWORD, 0x40010100);
+	rtw89_phy_write32_clr(rtwdev, R_IQK_RES + (path << 8), B_IQK_RES_RXCFIR);
+	rtw89_phy_write32_set(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_SEL);
+	rtw89_phy_write32_clr(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_G3);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8),
+			       B_CFIR_LUT_GP, group);
+	rtw89_phy_write32_set(rtwdev, R_IOQ_IQK_DPK, B_IOQ_IQK_DPK_EN);
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, B_NCTL_N1_CIP);
+	fail = _iqk_one_shot(rtwdev, phy_idx, path, ID_NBRXK);
+
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_SEL2G, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0);
+		break;
+	case RTW89_BAND_5G:
+		rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_SEL5G, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_WLSEL, RR_WLSEL_AG, 0x0);
+		break;
+	default:
+		break;
+	}
+	if (!fail) {
+		tmp = rtw89_phy_read32_mask(rtwdev, R_RXIQC + (path << 8), MASKDWORD);
+		iqk_info->nb_rxcfir[path] = tmp | 0x2;
+	} else {
+		iqk_info->nb_rxcfir[path] = 0x40000002;
+	}
+	return fail;
+}
+
+static void _iqk_rxclk_setting(struct rtw89_dev *rtwdev, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+
+	if (iqk_info->iqk_bw[path] == RTW89_CHANNEL_WIDTH_80) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+		rtw89_phy_write32_mask(rtwdev, R_CFIR_SYS + (path << 8),
+				       MASKDWORD, 0x4d000a08);
+		rtw89_phy_write32_mask(rtwdev, R_P0_RXCK + (path << 13),
+				       B_P0_RXCK_VAL, 0x2);
+		rtw89_phy_write32_set(rtwdev, R_P0_RXCK + (path << 13), B_P0_RXCK_ON);
+		rtw89_phy_write32_set(rtwdev, R_UPD_CLK_ADC, B_UPD_CLK_ADC_ON);
+		rtw89_phy_write32_mask(rtwdev, R_UPD_CLK_ADC, B_UPD_CLK_ADC_VAL, 0x1);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_CFIR_SYS + (path << 8),
+				       MASKDWORD, 0x44000a08);
+		rtw89_phy_write32_mask(rtwdev, R_P0_RXCK + (path << 13),
+				       B_P0_RXCK_VAL, 0x1);
+		rtw89_phy_write32_set(rtwdev, R_P0_RXCK + (path << 13), B_P0_RXCK_ON);
+		rtw89_phy_write32_set(rtwdev, R_UPD_CLK_ADC, B_UPD_CLK_ADC_ON);
+		rtw89_phy_write32_clr(rtwdev, R_UPD_CLK_ADC, B_UPD_CLK_ADC_VAL);
+	}
+}
+
+static bool _txk_group_sel(struct rtw89_dev *rtwdev,
+			   enum rtw89_phy_idx phy_idx, u8 path)
+{
+	static const u32 a_txgain[4] = {0xE466, 0x646D, 0xE4E2, 0x64ED};
+	static const u32 g_txgain[4] = {0x60e8, 0x60f0, 0x61e8, 0x61ED};
+	static const u32 a_itqt[4] = {0x12, 0x12, 0x12, 0x1b};
+	static const u32 g_itqt[4] = {0x09, 0x12, 0x12, 0x12};
+	static const u32 g_attsmxr[4] = {0x0, 0x1, 0x1, 0x1};
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	bool fail = false;
+	u8 gp = 0x0;
+	u32 tmp = 0x0;
+
+	for (gp = 0x0; gp < 0x4; gp++) {
+		switch (iqk_info->iqk_band[path]) {
+		case RTW89_BAND_2G:
+			rtw89_phy_write32_mask(rtwdev, R_RFGAIN_BND + (path << 8),
+					       B_RFGAIN_BND, 0x08);
+			rtw89_write_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_ALL,
+				       g_txgain[gp]);
+			rtw89_write_rf(rtwdev, path, RR_TXG1, RR_TXG1_ATT1,
+				       g_attsmxr[gp]);
+			rtw89_write_rf(rtwdev, path, RR_TXG2, RR_TXG2_ATT0,
+				       g_attsmxr[gp]);
+			rtw89_phy_write32_mask(rtwdev, R_KIP_IQP + (path << 8),
+					       MASKDWORD, g_itqt[gp]);
+			break;
+		case RTW89_BAND_5G:
+			rtw89_phy_write32_mask(rtwdev, R_RFGAIN_BND + (path << 8),
+					       B_RFGAIN_BND, 0x04);
+			rtw89_write_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_ALL,
+				       a_txgain[gp]);
+			rtw89_phy_write32_mask(rtwdev, R_KIP_IQP + (path << 8),
+					       MASKDWORD, a_itqt[gp]);
+			break;
+		default:
+			break;
+		}
+		rtw89_phy_write32_clr(rtwdev, R_IQK_RES + (path << 8), B_IQK_RES_TXCFIR);
+		rtw89_phy_write32_set(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_SEL);
+		rtw89_phy_write32_set(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_G3);
+		rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8),
+				       B_CFIR_LUT_GP, gp);
+		rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, B_NCTL_N1_CIP);
+		fail = _iqk_one_shot(rtwdev, phy_idx, path, ID_TXK);
+		rtw89_phy_write32_mask(rtwdev, R_IQKINF, BIT(8 + gp + path * 4), fail);
+	}
+
+	iqk_info->nb_txcfir[path] = 0x40000000;
+	rtw89_phy_write32_mask(rtwdev, R_IQK_RES + (path << 8),
+			       B_IQK_RES_TXCFIR, 0x5);
+	iqk_info->is_wb_txiqk[path] = true;
+	tmp = rtw89_phy_read32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, 0x8%lx38 = 0x%x\n", path,
+		    BIT(path), tmp);
+	return false;
+}
+
+static bool _iqk_nbtxk(struct rtw89_dev *rtwdev,
+		       enum rtw89_phy_idx phy_idx, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u8 group = 0x2;
+	u32 a_mode_txgain = 0x64e2;
+	u32 g_mode_txgain = 0x61e8;
+	u32 attsmxr = 0x1;
+	u32 itqt = 0x12;
+	u32 tmp = 0x0;
+	bool fail = false;
+
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_phy_write32_mask(rtwdev, R_RFGAIN_BND + (path << 8),
+				       B_RFGAIN_BND, 0x08);
+		rtw89_write_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_ALL, g_mode_txgain);
+		rtw89_write_rf(rtwdev, path, RR_TXG1, RR_TXG1_ATT1, attsmxr);
+		rtw89_write_rf(rtwdev, path, RR_TXG2, RR_TXG2_ATT0, attsmxr);
+		break;
+	case RTW89_BAND_5G:
+		rtw89_phy_write32_mask(rtwdev, R_RFGAIN_BND + (path << 8),
+				       B_RFGAIN_BND, 0x04);
+		rtw89_write_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_ALL, a_mode_txgain);
+		break;
+	default:
+		break;
+	}
+	rtw89_phy_write32_clr(rtwdev, R_IQK_RES + (path << 8), B_IQK_RES_TXCFIR);
+	rtw89_phy_write32_set(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_SEL);
+	rtw89_phy_write32_set(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_G3);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_GP, group);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_IQP + (path << 8), MASKDWORD, itqt);
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, B_NCTL_N1_CIP);
+	fail = _iqk_one_shot(rtwdev, phy_idx, path, ID_NBTXK);
+	if (!fail) {
+		tmp = rtw89_phy_read32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD);
+		iqk_info->nb_txcfir[path] = tmp | 0x2;
+	} else {
+		iqk_info->nb_txcfir[path] = 0x40000002;
+	}
+	tmp = rtw89_phy_read32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, 0x8%lx38 = 0x%x\n", path,
+		    BIT(path), tmp);
+	return fail;
+}
+
+static void _lok_res_table(struct rtw89_dev *rtwdev, u8 path, u8 ibias)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, ibias = %x\n", path, ibias);
+	rtw89_write_rf(rtwdev, path, RR_LUTWE, RFREG_MASK, 0x2);
+	if (iqk_info->iqk_band[path] == RTW89_BAND_2G)
+		rtw89_write_rf(rtwdev, path, RR_LUTWA, RFREG_MASK, 0x0);
+	else
+		rtw89_write_rf(rtwdev, path, RR_LUTWA, RFREG_MASK, 0x1);
+	rtw89_write_rf(rtwdev, path, RR_LUTWD0, RFREG_MASK, ibias);
+	rtw89_write_rf(rtwdev, path, RR_LUTWE, RFREG_MASK, 0x0);
+}
+
+static bool _lok_finetune_check(struct rtw89_dev *rtwdev, u8 path)
+{
+	bool is_fail = false;
+	u32 tmp = 0x0;
+	u32 core_i = 0x0;
+	u32 core_q = 0x0;
+
+	tmp = rtw89_read_rf(rtwdev, path, RR_TXMO, RFREG_MASK);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK][FineLOK] S%x, 0x58 = 0x%x\n",
+		    path, tmp);
+	core_i = FIELD_GET(RR_TXMO_COI, tmp);
+	core_q = FIELD_GET(RR_TXMO_COQ, tmp);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, i = 0x%x\n", path, core_i);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%x, q = 0x%x\n", path, core_q);
+
+	if (core_i < 0x2 || core_i > 0x1d || core_q < 0x2 || core_q > 0x1d)
+		is_fail = true;
+	return is_fail;
+}
+
+static bool _iqk_lok(struct rtw89_dev *rtwdev,
+		     enum rtw89_phy_idx phy_idx, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u32 rf0 = 0x0;
+	u8 itqt = 0x12;
+	bool fail = false;
+	bool tmp = false;
+
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_write_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_ALL, 0xe5e0);
+		itqt = 0x09;
+		break;
+	case RTW89_BAND_5G:
+		rtw89_write_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_ALL, 0xe4e0);
+		itqt = 0x12;
+		break;
+	default:
+		break;
+	}
+	rtw89_phy_write32_set(rtwdev, R_IQK_CFG, B_IQK_CFG_SET);
+	rf0 = rtw89_read_rf(rtwdev, path, RR_MOD, RFREG_MASK);
+	rtw89_phy_write32_mask(rtwdev, R_IQK_DIF1, B_IQK_DIF1_TXPI,
+			       rf0 | iqk_info->syn1to2);
+	rtw89_phy_write32_clr(rtwdev, R_IQK_RES + (path << 8), B_IQK_RES_TXCFIR);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_SEL, 0x1);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_G3, 0x1);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_GP, 0x0);
+	rtw89_phy_write32_set(rtwdev, R_IOQ_IQK_DPK, B_IOQ_IQK_DPK_EN);
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, B_NCTL_N1_CIP);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_IQP + (path << 8), MASKDWORD, itqt);
+	tmp = _iqk_one_shot(rtwdev, phy_idx, path, ID_FLOK_COARSE);
+	iqk_info->lok_cor_fail[0][path] = tmp;
+	fsleep(10);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_IQP + (path << 8), MASKDWORD, itqt);
+	tmp = _iqk_one_shot(rtwdev, phy_idx, path, ID_FLOK_FINE);
+	iqk_info->lok_fin_fail[0][path] = tmp;
+	fail = _lok_finetune_check(rtwdev, path);
+	return fail;
+}
+
+static void _iqk_txk_setting(struct rtw89_dev *rtwdev, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+
+	rtw89_phy_write32_set(rtwdev, R_P0_NRBW + (path << 13), B_P0_NRBW_DBG);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR_PW15, B_ANAPAR_PW15, 0x1f);
+	udelay(1);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR_PW15, B_ANAPAR_PW15, 0x13);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR, B_ANAPAR_15, 0x0001);
+	udelay(1);
+	rtw89_phy_write32_mask(rtwdev, R_ANAPAR, B_ANAPAR_15, 0x0041);
+	udelay(1);
+	rtw89_phy_write32_mask(rtwdev, R_ADC_FIFO, B_ADC_FIFO_RST, 0x0303);
+	rtw89_phy_write32_mask(rtwdev, R_ADC_FIFO, B_ADC_FIFO_RST, 0x0000);
+	switch (iqk_info->iqk_band[path]) {
+	case RTW89_BAND_2G:
+		rtw89_write_rf(rtwdev, path, RR_XALNA2, RR_XALNA2_SW, 0x00);
+		rtw89_write_rf(rtwdev, path, RR_RCKD, RR_RCKD_POW, 0x3f);
+		rtw89_write_rf(rtwdev, path, RR_TXG1, RR_TXG1_ATT2, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_TXG1, RR_TXG1_ATT1, 0x1);
+		rtw89_write_rf(rtwdev, path, RR_TXG2, RR_TXG2_ATT0, 0x1);
+		rtw89_write_rf(rtwdev, path, RR_TXGA, RR_TXGA_LOK_EN, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_LUTWE, RR_LUTWE_LOK, 0x1);
+		rtw89_write_rf(rtwdev, path, RR_LUTDBG, RR_LUTDBG_LOK, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_LUTWA, RR_LUTWA_MASK, 0x000);
+		rtw89_write_rf(rtwdev, path, RR_RSV2, RFREG_MASK, 0x80200);
+		rtw89_write_rf(rtwdev, path, RR_DTXLOK, RFREG_MASK, 0x80200);
+		rtw89_write_rf(rtwdev, path, RR_MOD, RFREG_MASK,
+			       0x403e0 | iqk_info->syn1to2);
+		udelay(1);
+		break;
+	case RTW89_BAND_5G:
+		rtw89_write_rf(rtwdev, path, RR_XGLNA2, RR_XGLNA2_SW, 0x00);
+		rtw89_write_rf(rtwdev, path, RR_RCKD, RR_RCKD_POW, 0x3f);
+		rtw89_write_rf(rtwdev, path, RR_BIASA, RR_BIASA_A, 0x7);
+		rtw89_write_rf(rtwdev, path, RR_TXGA, RR_TXGA_LOK_EN, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_LUTWE, RR_LUTWE_LOK, 0x1);
+		rtw89_write_rf(rtwdev, path, RR_LUTDBG, RR_LUTDBG_LOK, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_LUTWA, RR_LUTWA_MASK, 0x100);
+		rtw89_write_rf(rtwdev, path, RR_RSV2, RFREG_MASK, 0x80200);
+		rtw89_write_rf(rtwdev, path, RR_DTXLOK, RFREG_MASK, 0x80200);
+		rtw89_write_rf(rtwdev, path, RR_LUTWD0, RFREG_MASK, 0x1);
+		rtw89_write_rf(rtwdev, path, RR_LUTWD0, RFREG_MASK, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_MOD, RFREG_MASK,
+			       0x403e0 | iqk_info->syn1to2);
+		udelay(1);
+		break;
+	default:
+		break;
+	}
+}
+
+static void _iqk_txclk_setting(struct rtw89_dev *rtwdev, u8 path)
+{
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_SYS + (path << 8), MASKDWORD, 0xce000a08);
+}
+
+static void _iqk_info_iqk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx,
+			  u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u32 tmp = 0x0;
+	bool flag = 0x0;
+
+	iqk_info->thermal[path] =
+		ewma_thermal_read(&rtwdev->phystat.avg_thermal[path]);
+	iqk_info->thermal_rek_en = false;
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%d_thermal = %d\n", path,
+		    iqk_info->thermal[path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%d_LOK_COR_fail= %d\n", path,
+		    iqk_info->lok_cor_fail[0][path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%d_LOK_FIN_fail= %d\n", path,
+		    iqk_info->lok_fin_fail[0][path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%d_TXIQK_fail = %d\n", path,
+		    iqk_info->iqk_tx_fail[0][path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]S%d_RXIQK_fail= %d,\n", path,
+		    iqk_info->iqk_rx_fail[0][path]);
+	flag = iqk_info->lok_cor_fail[0][path];
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF, BIT(0) << (path * 4), flag);
+	flag = iqk_info->lok_fin_fail[0][path];
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF, BIT(1) << (path * 4), flag);
+	flag = iqk_info->iqk_tx_fail[0][path];
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF, BIT(2) << (path * 4), flag);
+	flag = iqk_info->iqk_rx_fail[0][path];
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF, BIT(3) << (path * 4), flag);
+
+	tmp = rtw89_phy_read32_mask(rtwdev, R_IQK_RES + (path << 8), MASKDWORD);
+	iqk_info->bp_iqkenable[path] = tmp;
+	tmp = rtw89_phy_read32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD);
+	iqk_info->bp_txkresult[path] = tmp;
+	tmp = rtw89_phy_read32_mask(rtwdev, R_RXIQC + (path << 8), MASKDWORD);
+	iqk_info->bp_rxkresult[path] = tmp;
+
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF2, B_IQKINF2_KCNT,
+			       (u8)iqk_info->iqk_times);
+
+	tmp = rtw89_phy_read32_mask(rtwdev, R_IQKINF, 0x0000000f << (path * 4));
+	if (tmp != 0x0)
+		iqk_info->iqk_fail_cnt++;
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF2, 0x00ff0000 << (path * 4),
+			       iqk_info->iqk_fail_cnt);
+}
+
+static
+void _iqk_by_path(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	bool lok_is_fail = false;
+	u8 ibias = 0x1;
+	u8 i = 0;
+
+	_iqk_txclk_setting(rtwdev, path);
+
+	for (i = 0; i < 3; i++) {
+		_lok_res_table(rtwdev, path, ibias++);
+		_iqk_txk_setting(rtwdev, path);
+		lok_is_fail = _iqk_lok(rtwdev, phy_idx, path);
+		if (!lok_is_fail)
+			break;
+	}
+	if (iqk_info->is_nbiqk)
+		iqk_info->iqk_tx_fail[0][path] = _iqk_nbtxk(rtwdev, phy_idx, path);
+	else
+		iqk_info->iqk_tx_fail[0][path] = _txk_group_sel(rtwdev, phy_idx, path);
+
+	_iqk_rxclk_setting(rtwdev, path);
+	_iqk_rxk_setting(rtwdev, path);
+	if (iqk_info->is_nbiqk || rtwdev->dbcc_en || iqk_info->iqk_band[path] == RTW89_BAND_2G)
+		iqk_info->iqk_rx_fail[0][path] = _iqk_nbrxk(rtwdev, phy_idx, path);
+	else
+		iqk_info->iqk_rx_fail[0][path] = _rxk_group_sel(rtwdev, phy_idx, path);
+
+	_iqk_info_iqk(rtwdev, phy_idx, path);
+}
+
+static void _iqk_get_ch_info(struct rtw89_dev *rtwdev,
+			     enum rtw89_phy_idx phy, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	struct rtw89_hal *hal = &rtwdev->hal;
+	u32 reg_rf18 = 0x0, reg_35c = 0x0;
+	u8 idx = 0;
+	u8 get_empty_table = false;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	for  (idx = 0; idx < RTW89_IQK_CHS_NR; idx++) {
+		if (iqk_info->iqk_mcc_ch[idx][path] == 0) {
+			get_empty_table = true;
+			break;
+		}
+	}
+	if (!get_empty_table) {
+		idx = iqk_info->iqk_table_idx[path] + 1;
+		if (idx > RTW89_IQK_CHS_NR - 1)
+			idx = 0;
+	}
+	reg_rf18 = rtw89_read_rf(rtwdev, path, RR_CFGCH, RFREG_MASK);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]cfg ch = %d\n", reg_rf18);
+	reg_35c = rtw89_phy_read32_mask(rtwdev, 0x35c, 0x00000c00);
+
+	iqk_info->iqk_band[path] = hal->current_band_type;
+	iqk_info->iqk_bw[path] = hal->current_band_width;
+	iqk_info->iqk_ch[path] = hal->current_channel;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[IQK]iqk_info->iqk_band[%x] = 0x%x\n", path,
+		    iqk_info->iqk_band[path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]iqk_info->iqk_bw[%x] = 0x%x\n",
+		    path, iqk_info->iqk_bw[path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]iqk_info->iqk_ch[%x] = 0x%x\n",
+		    path, iqk_info->iqk_ch[path]);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[IQK]S%d (PHY%d): / DBCC %s/ %s/ CH%d/ %s\n", path, phy,
+		    rtwdev->dbcc_en ? "on" : "off",
+		    iqk_info->iqk_band[path] == 0 ? "2G" :
+		    iqk_info->iqk_band[path] == 1 ? "5G" : "6G",
+		    iqk_info->iqk_ch[path],
+		    iqk_info->iqk_bw[path] == 0 ? "20M" :
+		    iqk_info->iqk_bw[path] == 1 ? "40M" : "80M");
+	if (reg_35c == 0x01)
+		iqk_info->syn1to2 = 0x1;
+	else
+		iqk_info->syn1to2 = 0x0;
+
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF, B_IQKINF_VER, RTW8852A_IQK_VER);
+	rtw89_phy_write32_mask(rtwdev, R_IQKCH, 0x000f << (path * 16),
+			       (u8)iqk_info->iqk_band[path]);
+	rtw89_phy_write32_mask(rtwdev, R_IQKCH, 0x00f0 << (path * 16),
+			       (u8)iqk_info->iqk_bw[path]);
+	rtw89_phy_write32_mask(rtwdev, R_IQKCH, 0xff00 << (path * 16),
+			       (u8)iqk_info->iqk_ch[path]);
+
+	rtw89_phy_write32_mask(rtwdev, R_IQKINF2, 0x000000ff, RTW8852A_NCTL_VER);
+}
+
+static void _iqk_start_iqk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx,
+			   u8 path)
+{
+	_iqk_by_path(rtwdev, phy_idx, path);
+}
+
+static void _iqk_restore(struct rtw89_dev *rtwdev, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+
+	rtw89_phy_write32_mask(rtwdev, R_TXIQC + (path << 8), MASKDWORD,
+			       iqk_info->nb_txcfir[path]);
+	rtw89_phy_write32_mask(rtwdev, R_RXIQC + (path << 8), MASKDWORD,
+			       iqk_info->nb_rxcfir[path]);
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_RPT, MASKDWORD);
+	rtw89_phy_write32_clr(rtwdev, R_MDPK_RX_DCK, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_SYSCFG, MASKDWORD, 0x80000000);
+	rtw89_phy_write32_clr(rtwdev, R_KPATH_CFG, MASKDWORD);
+	rtw89_phy_write32_clr(rtwdev, R_GAPK, B_GAPK_ADR);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_SYS + (path << 8), MASKDWORD, 0x10010000);
+	rtw89_phy_write32_clr(rtwdev, R_KIP + (path << 8), B_KIP_RFGAIN);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_MAP + (path << 8), MASKDWORD, 0xe4e4e4e4);
+	rtw89_phy_write32_clr(rtwdev, R_CFIR_LUT + (path << 8), B_CFIR_LUT_SEL);
+	rtw89_phy_write32_clr(rtwdev, R_KIP_IQP + (path << 8), B_KIP_IQP_IQSW);
+	rtw89_phy_write32_mask(rtwdev, R_LOAD_COEF + (path << 8), MASKDWORD, 0x00000002);
+	rtw89_write_rf(rtwdev, path, RR_LUTWE, RR_LUTWE_LOK, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_RCKD, RR_RCKD_POW, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_LUTWE, RR_LUTWE_LOK, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_RX);
+	rtw89_write_rf(rtwdev, path, RR_TXRSV, RR_TXRSV_GAPK, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_BIAS, RR_BIAS_GAPK, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_RSV1, RR_RSV1_RST, 0x1);
+}
+
+static void _iqk_afebb_restore(struct rtw89_dev *rtwdev,
+			       enum rtw89_phy_idx phy_idx, u8 path)
+{
+	const struct rtw89_rfk_tbl *tbl;
+
+	switch (_kpath(rtwdev, phy_idx)) {
+	case RF_A:
+		tbl = &rtw8852a_rfk_iqk_restore_defs_dbcc_path0_tbl;
+		break;
+	case RF_B:
+		tbl = &rtw8852a_rfk_iqk_restore_defs_dbcc_path1_tbl;
+		break;
+	default:
+		tbl = &rtw8852a_rfk_iqk_restore_defs_nondbcc_path01_tbl;
+		break;
+	}
+
+	rtw89_rfk_parser(rtwdev, tbl);
+}
+
+static void _iqk_preset(struct rtw89_dev *rtwdev, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u8 idx = iqk_info->iqk_table_idx[path];
+
+	if (rtwdev->dbcc_en) {
+		rtw89_phy_write32_mask(rtwdev, R_COEF_SEL + (path << 8),
+				       B_COEF_SEL_IQC, path & 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8),
+				       B_CFIR_LUT_G2, path & 0x1);
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_COEF_SEL + (path << 8),
+				       B_COEF_SEL_IQC, idx);
+		rtw89_phy_write32_mask(rtwdev, R_CFIR_LUT + (path << 8),
+				       B_CFIR_LUT_G2, idx);
+	}
+	rtw89_write_rf(rtwdev, path, RR_RSV1, RR_RSV1_RST, 0x0);
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_RPT, MASKDWORD, 0x00000080);
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_RW, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_SYSCFG, MASKDWORD, 0x81ff010a);
+	rtw89_phy_write32_mask(rtwdev, R_KPATH_CFG, MASKDWORD, 0x00200000);
+	rtw89_phy_write32_mask(rtwdev, R_MDPK_RX_DCK, MASKDWORD, 0x80000000);
+	rtw89_phy_write32_clr(rtwdev, R_LOAD_COEF + (path << 8), MASKDWORD);
+}
+
+static void _iqk_macbb_setting(struct rtw89_dev *rtwdev,
+			       enum rtw89_phy_idx phy_idx, u8 path)
+{
+	const struct rtw89_rfk_tbl *tbl;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===> %s\n", __func__);
+
+	switch (_kpath(rtwdev, phy_idx)) {
+	case RF_A:
+		tbl = &rtw8852a_rfk_iqk_set_defs_dbcc_path0_tbl;
+		break;
+	case RF_B:
+		tbl = &rtw8852a_rfk_iqk_set_defs_dbcc_path1_tbl;
+		break;
+	default:
+		tbl = &rtw8852a_rfk_iqk_set_defs_nondbcc_path01_tbl;
+		break;
+	}
+
+	rtw89_rfk_parser(rtwdev, tbl);
+}
+
+static void _iqk_dbcc(struct rtw89_dev *rtwdev, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u8 phy_idx = 0x0;
+
+	iqk_info->iqk_times++;
+
+	if (path == 0x0)
+		phy_idx = RTW89_PHY_0;
+	else
+		phy_idx = RTW89_PHY_1;
+
+	_iqk_get_ch_info(rtwdev, phy_idx, path);
+	_iqk_macbb_setting(rtwdev, phy_idx, path);
+	_iqk_preset(rtwdev, path);
+	_iqk_start_iqk(rtwdev, phy_idx, path);
+	_iqk_restore(rtwdev, path);
+	_iqk_afebb_restore(rtwdev, phy_idx, path);
+}
+
+static void _iqk_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_iqk_info *iqk = &rtwdev->iqk;
+	u8 path = 0x0;
+	u8 cur_ther;
+
+	if (iqk->iqk_band[0] == RTW89_BAND_2G)
+		return;
+	if (iqk->iqk_bw[0] < RTW89_CHANNEL_WIDTH_80)
+		return;
+
+	/* only check path 0 */
+	for (path = 0; path < 1; path++) {
+		cur_ther = ewma_thermal_read(&rtwdev->phystat.avg_thermal[path]);
+
+		if (abs(cur_ther - iqk->thermal[path]) > RTW8852A_IQK_THR_REK)
+			iqk->thermal_rek_en = true;
+		else
+			iqk->thermal_rek_en = false;
+	}
+}
+
+static void _rck(struct rtw89_dev *rtwdev, enum rtw89_rf_path path)
+{
+	u32 rf_reg5, rck_val = 0;
+	u32 val;
+	int ret;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[RCK] ====== S%d RCK ======\n", path);
+
+	rf_reg5 = rtw89_read_rf(rtwdev, path, RR_RSV1, RFREG_MASK);
+
+	rtw89_write_rf(rtwdev, path, RR_RSV1, RR_RSV1_RST, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_RX);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[RCK] RF0x00 = 0x%x\n",
+		    rtw89_read_rf(rtwdev, path, RR_MOD, RFREG_MASK));
+
+	/* RCK trigger */
+	rtw89_write_rf(rtwdev, path, RR_RCKC, RFREG_MASK, 0x00240);
+
+	ret = read_poll_timeout_atomic(rtw89_read_rf, val, val, 2, 20,
+				       false, rtwdev, path, 0x1c, BIT(3));
+	if (ret)
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[RCK] RCK timeout\n");
+
+	rck_val = rtw89_read_rf(rtwdev, path, RR_RCKC, RR_RCKC_CA);
+	rtw89_write_rf(rtwdev, path, RR_RCKC, RFREG_MASK, rck_val);
+
+	/* RCK_ADC_OFFSET */
+	rtw89_write_rf(rtwdev, path, RR_RCKO, RR_RCKO_OFF, 0x4);
+
+	rtw89_write_rf(rtwdev, path, RR_RFC, RR_RFC_CKEN, 0x1);
+	rtw89_write_rf(rtwdev, path, RR_RFC, RR_RFC_CKEN, 0x0);
+
+	rtw89_write_rf(rtwdev, path, RR_RSV1, RFREG_MASK, rf_reg5);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[RCK] RF 0x1b / 0x1c / 0x1d = 0x%x / 0x%x / 0x%x\n",
+		    rtw89_read_rf(rtwdev, path, RR_RCKC, RFREG_MASK),
+		    rtw89_read_rf(rtwdev, path, RR_RCKS, RFREG_MASK),
+		    rtw89_read_rf(rtwdev, path, RR_RCKO, RFREG_MASK));
+}
+
+static void _iqk_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u8 ch, path;
+
+	rtw89_phy_write32_clr(rtwdev, R_IQKINF, MASKDWORD);
+	if (iqk_info->is_iqk_init)
+		return;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]===>%s\n", __func__);
+	iqk_info->is_iqk_init = true;
+	iqk_info->is_nbiqk = false;
+	iqk_info->iqk_fft_en = false;
+	iqk_info->iqk_sram_en = false;
+	iqk_info->iqk_cfir_en = false;
+	iqk_info->iqk_xym_en = false;
+	iqk_info->thermal_rek_en = false;
+	iqk_info->iqk_times = 0x0;
+
+	for (ch = 0; ch < RTW89_IQK_CHS_NR; ch++) {
+		iqk_info->iqk_channel[ch] = 0x0;
+		for (path = 0; path < RTW8852A_IQK_SS; path++) {
+			iqk_info->lok_cor_fail[ch][path] = false;
+			iqk_info->lok_fin_fail[ch][path] = false;
+			iqk_info->iqk_tx_fail[ch][path] = false;
+			iqk_info->iqk_rx_fail[ch][path] = false;
+			iqk_info->iqk_mcc_ch[ch][path] = 0x0;
+			iqk_info->iqk_table_idx[path] = 0x0;
+		}
+	}
+}
+
+static void _doiqk(struct rtw89_dev *rtwdev, bool force,
+		   enum rtw89_phy_idx phy_idx, u8 path)
+{
+	struct rtw89_iqk_info *iqk_info = &rtwdev->iqk;
+	u32 backup_bb_val[BACKUP_BB_REGS_NR];
+	u32 backup_rf_val[RTW8852A_IQK_SS][BACKUP_RF_REGS_NR];
+	u8 phy_map = rtw89_btc_phymap(rtwdev, phy_idx, RF_AB);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_IQK, BTC_WRFK_ONESHOT_START);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[IQK]==========IQK strat!!!!!==========\n");
+	iqk_info->iqk_times++;
+	iqk_info->kcount = 0;
+	iqk_info->version = RTW8852A_IQK_VER;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[IQK]Test Ver 0x%x\n", iqk_info->version);
+	_iqk_get_ch_info(rtwdev, phy_idx, path);
+	_rfk_backup_bb_reg(rtwdev, &backup_bb_val[0]);
+	_rfk_backup_rf_reg(rtwdev, &backup_rf_val[path][0], path);
+	_iqk_macbb_setting(rtwdev, phy_idx, path);
+	_iqk_preset(rtwdev, path);
+	_iqk_start_iqk(rtwdev, phy_idx, path);
+	_iqk_restore(rtwdev, path);
+	_iqk_afebb_restore(rtwdev, phy_idx, path);
+	_rfk_restore_bb_reg(rtwdev, &backup_bb_val[0]);
+	_rfk_restore_rf_reg(rtwdev, &backup_rf_val[path][0], path);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_IQK, BTC_WRFK_ONESHOT_STOP);
+}
+
+static void _iqk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx, bool force)
+{
+	switch (_kpath(rtwdev, phy_idx)) {
+	case RF_A:
+		_doiqk(rtwdev, force, phy_idx, RF_PATH_A);
+		break;
+	case RF_B:
+		_doiqk(rtwdev, force, phy_idx, RF_PATH_B);
+		break;
+	case RF_AB:
+		_doiqk(rtwdev, force, phy_idx, RF_PATH_A);
+		_doiqk(rtwdev, force, phy_idx, RF_PATH_B);
+		break;
+	default:
+		break;
+	}
+}
+
+#define RXDCK_VER_8852A 0xe
+
+static void _set_rx_dck(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			enum rtw89_rf_path path, bool is_afe)
+{
+	u8 phy_map = rtw89_btc_path_phymap(rtwdev, phy, path);
+	u32 ori_val;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[RX_DCK] ==== S%d RX DCK (by %s)====\n",
+		    path, is_afe ? "AFE" : "RFC");
+
+	ori_val = rtw89_phy_read32_mask(rtwdev, R_P0_RXCK + (path << 13), MASKDWORD);
+
+	if (is_afe) {
+		rtw89_phy_write32_set(rtwdev, R_P0_NRBW + (path << 13), B_P0_NRBW_DBG);
+		rtw89_phy_write32_set(rtwdev, R_P0_RXCK + (path << 13), B_P0_RXCK_ON);
+		rtw89_phy_write32_mask(rtwdev, R_P0_RXCK + (path << 13),
+				       B_P0_RXCK_VAL, 0x3);
+		rtw89_phy_write32_set(rtwdev, R_S0_RXDC2 + (path << 13), B_S0_RXDC2_MEN);
+		rtw89_phy_write32_mask(rtwdev, R_S0_RXDC2 + (path << 13),
+				       B_S0_RXDC2_AVG, 0x3);
+		rtw89_phy_write32_mask(rtwdev, R_ANAPAR_PW15, B_ANAPAR_PW15_H, 0x3);
+		rtw89_phy_write32_clr(rtwdev, R_ANAPAR, B_ANAPAR_ADCCLK);
+		rtw89_phy_write32_clr(rtwdev, R_ANAPAR, B_ANAPAR_FLTRST);
+		rtw89_phy_write32_set(rtwdev, R_ANAPAR, B_ANAPAR_FLTRST);
+		rtw89_phy_write32_mask(rtwdev, R_ANAPAR, B_ANAPAR_CRXBB, 0x1);
+	}
+
+	rtw89_write_rf(rtwdev, path, RR_DCK2, RR_DCK2_CYCLE, 0x3f);
+	rtw89_write_rf(rtwdev, path, RR_DCK1, RR_DCK1_SEL, is_afe);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_RXDCK, BTC_WRFK_ONESHOT_START);
+
+	rtw89_write_rf(rtwdev, path, RR_DCK, RR_DCK_LV, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_DCK, RR_DCK_LV, 0x1);
+
+	fsleep(600);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_RXDCK, BTC_WRFK_ONESHOT_STOP);
+
+	rtw89_write_rf(rtwdev, path, RR_DCK, RR_DCK_LV, 0x0);
+
+	if (is_afe) {
+		rtw89_phy_write32_clr(rtwdev, R_P0_NRBW + (path << 13), B_P0_NRBW_DBG);
+		rtw89_phy_write32_mask(rtwdev, R_P0_RXCK + (path << 13),
+				       MASKDWORD, ori_val);
+	}
+}
+
+static void _rx_dck(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+		    bool is_afe)
+{
+	u8 path, kpath, dck_tune;
+	u32 rf_reg5;
+	u32 addr;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[RX_DCK] ****** RXDCK Start (Ver: 0x%x, Cv: %d) ******\n",
+		    RXDCK_VER_8852A, rtwdev->hal.cv);
+
+	kpath = _kpath(rtwdev, phy);
+
+	for (path = 0; path < 2; path++) {
+		if (!(kpath & BIT(path)))
+			continue;
+
+		rf_reg5 = rtw89_read_rf(rtwdev, path, RR_RSV1, RFREG_MASK);
+		dck_tune = (u8)rtw89_read_rf(rtwdev, path, RR_DCK, RR_DCK_FINE);
+
+		if (rtwdev->is_tssi_mode[path]) {
+			addr = 0x5818 + (path << 13);
+			/* TSSI pause */
+			rtw89_phy_write32_set(rtwdev, addr, BIT(30));
+		}
+
+		rtw89_write_rf(rtwdev, path, RR_RSV1, RR_RSV1_RST, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_DCK, RR_DCK_FINE, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_RX);
+		_set_rx_dck(rtwdev, phy, path, is_afe);
+		rtw89_write_rf(rtwdev, path, RR_DCK, RR_DCK_FINE, dck_tune);
+		rtw89_write_rf(rtwdev, path, RR_RSV1, RFREG_MASK, rf_reg5);
+
+		if (rtwdev->is_tssi_mode[path]) {
+			addr = 0x5818 + (path << 13);
+			/* TSSI resume */
+			rtw89_phy_write32_clr(rtwdev, addr, BIT(30));
+		}
+	}
+}
+
+#define RTW8852A_RF_REL_VERSION 34
+#define RTW8852A_DPK_VER 0x10
+#define RTW8852A_DPK_TH_AVG_NUM 4
+#define RTW8852A_DPK_RF_PATH 2
+#define RTW8852A_DPK_KIP_REG_NUM 2
+
+enum rtw8852a_dpk_id {
+	LBK_RXIQK	= 0x06,
+	SYNC		= 0x10,
+	MDPK_IDL	= 0x11,
+	MDPK_MPA	= 0x12,
+	GAIN_LOSS	= 0x13,
+	GAIN_CAL	= 0x14,
+};
+
+static void _rf_direct_cntrl(struct rtw89_dev *rtwdev,
+			     enum rtw89_rf_path path, bool is_bybb)
+{
+	if (is_bybb)
+		rtw89_write_rf(rtwdev, path, RR_RSV1, RR_RSV1_RST, 0x1);
+	else
+		rtw89_write_rf(rtwdev, path, RR_RSV1, RR_RSV1_RST, 0x0);
+}
+
+static void _dpk_onoff(struct rtw89_dev *rtwdev,
+		       enum rtw89_rf_path path, bool off);
+
+static void _dpk_bkup_kip(struct rtw89_dev *rtwdev, u32 *reg,
+			  u32 reg_bkup[][RTW8852A_DPK_KIP_REG_NUM],
+			  u8 path)
+{
+	u8 i;
+
+	for (i = 0; i < RTW8852A_DPK_KIP_REG_NUM; i++) {
+		reg_bkup[path][i] = rtw89_phy_read32_mask(rtwdev,
+							  reg[i] + (path << 8),
+							  MASKDWORD);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] Backup 0x%x = %x\n",
+			    reg[i] + (path << 8), reg_bkup[path][i]);
+	}
+}
+
+static void _dpk_reload_kip(struct rtw89_dev *rtwdev, u32 *reg,
+			    u32 reg_bkup[][RTW8852A_DPK_KIP_REG_NUM], u8 path)
+{
+	u8 i;
+
+	for (i = 0; i < RTW8852A_DPK_KIP_REG_NUM; i++) {
+		rtw89_phy_write32_mask(rtwdev, reg[i] + (path << 8),
+				       MASKDWORD, reg_bkup[path][i]);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] Reload 0x%x = %x\n",
+			    reg[i] + (path << 8), reg_bkup[path][i]);
+	}
+}
+
+static u8 _dpk_one_shot(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			enum rtw89_rf_path path, enum rtw8852a_dpk_id id)
+{
+	u8 phy_map  = rtw89_btc_path_phymap(rtwdev, phy, path);
+	u16 dpk_cmd = 0x0;
+	u32 val;
+	int ret;
+
+	dpk_cmd = (u16)((id << 8) | (0x19 + (path << 4)));
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DPK, BTC_WRFK_ONESHOT_START);
+
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_CFG, MASKDWORD, dpk_cmd);
+	rtw89_phy_write32_set(rtwdev, R_DPK_CTL, B_DPK_CTL_EN);
+
+	ret = read_poll_timeout_atomic(rtw89_phy_read32_mask, val, val == 0x55,
+				       10, 20000, false, rtwdev, 0xbff8, MASKBYTE0);
+
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_N1, MASKBYTE0);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DPK, BTC_WRFK_ONESHOT_STOP);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] one-shot for %s = 0x%x (ret=%d)\n",
+		    id == 0x06 ? "LBK_RXIQK" :
+		    id == 0x10 ? "SYNC" :
+		    id == 0x11 ? "MDPK_IDL" :
+		    id == 0x12 ? "MDPK_MPA" :
+		    id == 0x13 ? "GAIN_LOSS" : "PWR_CAL",
+		    dpk_cmd, ret);
+
+	if (ret) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] one-shot over 20ms!!!!\n");
+		return 1;
+	}
+
+	return 0;
+}
+
+static void _dpk_rx_dck(struct rtw89_dev *rtwdev,
+			enum rtw89_phy_idx phy,
+			enum rtw89_rf_path path)
+{
+	rtw89_write_rf(rtwdev, path, RR_RXBB2, RR_EN_TIA_IDA, 0x3);
+	_set_rx_dck(rtwdev, phy, path, false);
+}
+
+static void _dpk_information(struct rtw89_dev *rtwdev,
+			     enum rtw89_phy_idx phy,
+			     enum rtw89_rf_path path)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	struct rtw89_hal *hal = &rtwdev->hal;
+
+	u8 kidx = dpk->cur_idx[path];
+
+	dpk->bp[path][kidx].band = hal->current_band_type;
+	dpk->bp[path][kidx].ch = hal->current_channel;
+	dpk->bp[path][kidx].bw = hal->current_band_width;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] S%d[%d] (PHY%d): TSSI %s/ DBCC %s/ %s/ CH%d/ %s\n",
+		    path, dpk->cur_idx[path], phy,
+		    rtwdev->is_tssi_mode[path] ? "on" : "off",
+		    rtwdev->dbcc_en ? "on" : "off",
+		    dpk->bp[path][kidx].band == 0 ? "2G" :
+		    dpk->bp[path][kidx].band == 1 ? "5G" : "6G",
+		    dpk->bp[path][kidx].ch,
+		    dpk->bp[path][kidx].bw == 0 ? "20M" :
+		    dpk->bp[path][kidx].bw == 1 ? "40M" : "80M");
+}
+
+static void _dpk_bb_afe_setting(struct rtw89_dev *rtwdev,
+				enum rtw89_phy_idx phy,
+				enum rtw89_rf_path path, u8 kpath)
+{
+	switch (kpath) {
+	case RF_A:
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_sf_defs_a_tbl);
+
+		if (rtw89_phy_read32_mask(rtwdev, R_2P4G_BAND, B_2P4G_BAND_SEL) == 0x0)
+			rtw89_phy_write32_set(rtwdev, R_RXCCA, B_RXCCA_DIS);
+
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_sr_defs_a_tbl);
+		break;
+	case RF_B:
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_sf_defs_b_tbl);
+
+		if (rtw89_phy_read32_mask(rtwdev, R_2P4G_BAND, B_2P4G_BAND_SEL) == 0x1)
+			rtw89_phy_write32_set(rtwdev, R_RXCCA, B_RXCCA_DIS);
+
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_sr_defs_b_tbl);
+		break;
+	case RF_AB:
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_s_defs_ab_tbl);
+		break;
+	default:
+		break;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] Set BB/AFE for PHY%d (kpath=%d)\n", phy, kpath);
+}
+
+static void _dpk_bb_afe_restore(struct rtw89_dev *rtwdev,
+				enum rtw89_phy_idx phy,
+				enum rtw89_rf_path path, u8 kpath)
+{
+	switch (kpath) {
+	case RF_A:
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_r_defs_a_tbl);
+		break;
+	case RF_B:
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_r_defs_b_tbl);
+		break;
+	case RF_AB:
+		rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_bb_afe_r_defs_ab_tbl);
+		break;
+	default:
+		break;
+	}
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] Restore BB/AFE for PHY%d (kpath=%d)\n", phy, kpath);
+}
+
+static void _dpk_tssi_pause(struct rtw89_dev *rtwdev,
+			    enum rtw89_rf_path path, bool is_pause)
+{
+	rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_TRK + (path << 13),
+			       B_P0_TSSI_TRK_EN, is_pause);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] S%d TSSI %s\n", path,
+		    is_pause ? "pause" : "resume");
+}
+
+static void _dpk_kip_setting(struct rtw89_dev *rtwdev,
+			     enum rtw89_rf_path path, u8 kidx)
+{
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_RPT, MASKDWORD, 0x00000080);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_CLK, MASKDWORD, 0x00093f3f);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_SYSCFG, MASKDWORD, 0x807f030a);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_SYS + (path << 8), MASKDWORD, 0xce000a08);
+	rtw89_phy_write32_mask(rtwdev, R_DPK_CFG, B_DPK_CFG_IDX, 0x2);
+	rtw89_phy_write32_mask(rtwdev, R_NCTL_CFG, B_NCTL_CFG_SPAGE, path); /*subpage_id*/
+	rtw89_phy_write32_mask(rtwdev, R_DPD_CH0 + (path << 8) + (kidx << 2),
+			       MASKDWORD, 0x003f2e2e);
+	rtw89_phy_write32_mask(rtwdev, R_DPD_CH0A + (path << 8) + (kidx << 2),
+			       MASKDWORD, 0x005b5b5b);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] KIP setting for S%d[%d]!!\n",
+		    path, kidx);
+}
+
+static void _dpk_kip_restore(struct rtw89_dev *rtwdev,
+			     enum rtw89_rf_path path)
+{
+	rtw89_phy_write32_clr(rtwdev, R_NCTL_RPT, MASKDWORD);
+	rtw89_phy_write32_mask(rtwdev, R_KIP_SYSCFG, MASKDWORD, 0x80000000);
+	rtw89_phy_write32_mask(rtwdev, R_CFIR_SYS + (path << 8), MASKDWORD, 0x10010000);
+	rtw89_phy_write32_clr(rtwdev, R_KIP_CLK, MASKDWORD);
+
+	if (rtwdev->hal.cv > CHIP_CBV)
+		rtw89_phy_write32_mask(rtwdev, R_DPD_COM + (path << 8), BIT(15), 0x1);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] S%d restore KIP\n", path);
+}
+
+static void _dpk_lbk_rxiqk(struct rtw89_dev *rtwdev,
+			   enum rtw89_phy_idx phy,
+			   enum rtw89_rf_path path)
+{
+	u8 cur_rxbb;
+
+	cur_rxbb = (u8)rtw89_read_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXBB);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_lbk_rxiqk_defs_f_tbl);
+
+	rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, 0xc);
+	rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_PLLEN, 0x1);
+	rtw89_write_rf(rtwdev, path, RR_RXPOW, RR_RXPOW_IQK, 0x2);
+	rtw89_write_rf(rtwdev, path, RR_RSV4, RFREG_MASK,
+		       rtw89_read_rf(rtwdev, path, RR_CFGCH, RFREG_MASK));
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_OFF, 0x13);
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x1);
+
+	fsleep(70);
+
+	rtw89_write_rf(rtwdev, path, RR_RXIQGEN, RR_RXIQGEN_ATTL, 0x1f);
+
+	if (cur_rxbb <= 0xa)
+		rtw89_write_rf(rtwdev, path, RR_RXIQGEN, RR_RXIQGEN_ATTH, 0x3);
+	else if (cur_rxbb <= 0x10 && cur_rxbb >= 0xb)
+		rtw89_write_rf(rtwdev, path, RR_RXIQGEN, RR_RXIQGEN_ATTH, 0x1);
+	else
+		rtw89_write_rf(rtwdev, path, RR_RXIQGEN, RR_RXIQGEN_ATTH, 0x0);
+
+	rtw89_phy_write32_mask(rtwdev, R_IQK_DIF4, B_IQK_DIF4_RXT, 0x11);
+
+	_dpk_one_shot(rtwdev, phy, path, LBK_RXIQK);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] S%d LBK RXIQC = 0x%x\n", path,
+		    rtw89_phy_read32_mask(rtwdev, R_RXIQC, MASKDWORD));
+
+	rtw89_write_rf(rtwdev, path, RR_RXK, RR_RXK_PLLEN, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_RXPOW, RR_RXPOW_IQK, 0x0);
+	rtw89_write_rf(rtwdev, path, RR_RXKPLL, RR_RXKPLL_POW, 0x0); /*POW IQKPLL*/
+	rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_DPK);
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_lbk_rxiqk_defs_r_tbl);
+}
+
+static void _dpk_get_thermal(struct rtw89_dev *rtwdev, u8 kidx,
+			     enum rtw89_rf_path path)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+
+	dpk->bp[path][kidx].ther_dpk =
+		ewma_thermal_read(&rtwdev->phystat.avg_thermal[path]);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] thermal at DPK = 0x%x\n",
+		    dpk->bp[path][kidx].ther_dpk);
+}
+
+static u8 _dpk_set_tx_pwr(struct rtw89_dev *rtwdev, u8 gain,
+			  enum rtw89_rf_path path)
+{
+	u8 txagc_ori = 0x38;
+
+	rtw89_write_rf(rtwdev, path, RR_MODOPT, RFREG_MASK, txagc_ori);
+
+	return txagc_ori;
+}
+
+static void _dpk_rf_setting(struct rtw89_dev *rtwdev, u8 gain,
+			    enum rtw89_rf_path path, u8 kidx)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+
+	if (dpk->bp[path][kidx].band == RTW89_BAND_2G) {
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_DPK, 0x280b);
+		rtw89_write_rf(rtwdev, path, RR_RXBB, RR_RXBB_ATTC, 0x0);
+		rtw89_write_rf(rtwdev, path, RR_RXBB, RR_RXBB_ATTR, 0x4);
+		rtw89_write_rf(rtwdev, path, RR_MIXER, RR_MIXER_GN, 0x0);
+	} else {
+		rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_DPK, 0x282e);
+		rtw89_write_rf(rtwdev, path, RR_BIASA2, RR_BIASA2_LB, 0x7);
+		rtw89_write_rf(rtwdev, path, RR_TXATANK, RR_TXATANK_LBSW, 0x3);
+		rtw89_write_rf(rtwdev, path, RR_RXA, RR_RXA_DPK, 0x3);
+	}
+	rtw89_write_rf(rtwdev, path, RR_RCKD, RR_RCKD_BW, 0x1);
+	rtw89_write_rf(rtwdev, path, RR_BTC, RR_BTC_TXBB, dpk->bp[path][kidx].bw + 1);
+	rtw89_write_rf(rtwdev, path, RR_BTC, RR_BTC_RXBB, 0x0);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] RF 0x0/0x1/0x1a = 0x%x/ 0x%x/ 0x%x\n",
+		    rtw89_read_rf(rtwdev, path, RR_MOD, RFREG_MASK),
+		    rtw89_read_rf(rtwdev, path, RR_MODOPT, RFREG_MASK),
+		    rtw89_read_rf(rtwdev, path, RR_BTC, RFREG_MASK));
+}
+
+static void _dpk_manual_txcfir(struct rtw89_dev *rtwdev,
+			       enum rtw89_rf_path path, bool is_manual)
+{
+	u8 tmp_pad, tmp_txbb;
+
+	if (is_manual) {
+		rtw89_phy_write32_mask(rtwdev, R_KIP + (path << 8), B_KIP_RFGAIN, 0x1);
+		tmp_pad = (u8)rtw89_read_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_PAD);
+		rtw89_phy_write32_mask(rtwdev, R_RFGAIN + (path << 8),
+				       B_RFGAIN_PAD, tmp_pad);
+
+		tmp_txbb = (u8)rtw89_read_rf(rtwdev, path, RR_GAINTX, RR_GAINTX_BB);
+		rtw89_phy_write32_mask(rtwdev, R_RFGAIN + (path << 8),
+				       B_RFGAIN_TXBB, tmp_txbb);
+
+		rtw89_phy_write32_mask(rtwdev, R_LOAD_COEF + (path << 8),
+				       B_LOAD_COEF_CFIR, 0x1);
+		rtw89_phy_write32_clr(rtwdev, R_LOAD_COEF + (path << 8),
+				      B_LOAD_COEF_CFIR);
+
+		rtw89_phy_write32_mask(rtwdev, R_LOAD_COEF + (path << 8), BIT(1), 0x1);
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] PAD_man / TXBB_man = 0x%x / 0x%x\n", tmp_pad,
+			    tmp_txbb);
+	} else {
+		rtw89_phy_write32_clr(rtwdev, R_KIP + (path << 8), B_KIP_RFGAIN);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] disable manual switch TXCFIR\n");
+	}
+}
+
+static void _dpk_bypass_rxcfir(struct rtw89_dev *rtwdev,
+			       enum rtw89_rf_path path, bool is_bypass)
+{
+	if (is_bypass) {
+		rtw89_phy_write32_mask(rtwdev, R_RXIQC + (path << 8),
+				       B_RXIQC_BYPASS2, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_RXIQC + (path << 8),
+				       B_RXIQC_BYPASS, 0x1);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] Bypass RXIQC (0x8%d3c = 0x%x)\n", 1 + path,
+			    rtw89_phy_read32_mask(rtwdev, R_RXIQC + (path << 8),
+						  MASKDWORD));
+	} else {
+		rtw89_phy_write32_clr(rtwdev, R_RXIQC + (path << 8), B_RXIQC_BYPASS2);
+		rtw89_phy_write32_clr(rtwdev, R_RXIQC + (path << 8), B_RXIQC_BYPASS);
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] restore 0x8%d3c = 0x%x\n", 1 + path,
+			    rtw89_phy_read32_mask(rtwdev, R_RXIQC + (path << 8),
+						  MASKDWORD));
+	}
+}
+
+static
+void _dpk_tpg_sel(struct rtw89_dev *rtwdev, enum rtw89_rf_path path, u8 kidx)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+
+	if (dpk->bp[path][kidx].bw == RTW89_CHANNEL_WIDTH_80)
+		rtw89_phy_write32_clr(rtwdev, R_TPG_MOD, B_TPG_MOD_F);
+	else if (dpk->bp[path][kidx].bw == RTW89_CHANNEL_WIDTH_40)
+		rtw89_phy_write32_mask(rtwdev, R_TPG_MOD, B_TPG_MOD_F, 0x2);
+	else
+		rtw89_phy_write32_mask(rtwdev, R_TPG_MOD, B_TPG_MOD_F, 0x1);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] TPG_Select for %s\n",
+		    dpk->bp[path][kidx].bw == RTW89_CHANNEL_WIDTH_80 ? "80M" :
+		    dpk->bp[path][kidx].bw == RTW89_CHANNEL_WIDTH_40 ? "40M" : "20M");
+}
+
+static void _dpk_table_select(struct rtw89_dev *rtwdev,
+			      enum rtw89_rf_path path, u8 kidx, u8 gain)
+{
+	u8 val;
+
+	val = 0x80 + kidx * 0x20 + gain * 0x10;
+	rtw89_phy_write32_mask(rtwdev, R_DPD_CH0 + (path << 8), MASKBYTE3, val);
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] table select for Kidx[%d], Gain[%d] (0x%x)\n", kidx,
+		    gain, val);
+}
+
+static bool _dpk_sync_check(struct rtw89_dev *rtwdev,
+			    enum rtw89_rf_path path)
+{
+#define DPK_SYNC_TH_DC_I 200
+#define DPK_SYNC_TH_DC_Q 200
+#define DPK_SYNC_TH_CORR 170
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	u16 dc_i, dc_q;
+	u8 corr_val, corr_idx;
+
+	rtw89_phy_write32_clr(rtwdev, R_KIP_RPT1, B_KIP_RPT1_SEL);
+
+	corr_idx = (u8)rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_CORI);
+	corr_val = (u8)rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_CORV);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] S%d Corr_idx / Corr_val = %d / %d\n", path, corr_idx,
+		    corr_val);
+
+	dpk->corr_idx[path] = corr_idx;
+	dpk->corr_val[path] = corr_val;
+
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, B_KIP_RPT1_SEL, 0x9);
+
+	dc_i = (u16)rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_DCI);
+	dc_q = (u16)rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_DCQ);
+
+	dc_i = abs(sign_extend32(dc_i, 11));
+	dc_q = abs(sign_extend32(dc_q, 11));
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] S%d DC I/Q, = %d / %d\n",
+		    path, dc_i, dc_q);
+
+	dpk->dc_i[path] = dc_i;
+	dpk->dc_q[path] = dc_q;
+
+	if (dc_i > DPK_SYNC_TH_DC_I || dc_q > DPK_SYNC_TH_DC_Q ||
+	    corr_val < DPK_SYNC_TH_CORR)
+		return true;
+	else
+		return false;
+}
+
+static bool _dpk_sync(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+		      enum rtw89_rf_path path, u8 kidx)
+{
+	_dpk_tpg_sel(rtwdev, path, kidx);
+	_dpk_one_shot(rtwdev, phy, path, SYNC);
+	return _dpk_sync_check(rtwdev, path); /*1= fail*/
+}
+
+static u16 _dpk_dgain_read(struct rtw89_dev *rtwdev)
+{
+	u16 dgain = 0x0;
+
+	rtw89_phy_write32_clr(rtwdev, R_KIP_RPT1, B_KIP_RPT1_SEL);
+
+	rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_SYNERR);
+
+	dgain = (u16)rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_DCI);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] DGain = 0x%x (%d)\n", dgain,
+		    dgain);
+
+	return dgain;
+}
+
+static s8 _dpk_dgain_mapping(struct rtw89_dev *rtwdev, u16 dgain)
+{
+	s8 offset;
+
+	if (dgain >= 0x783)
+		offset = 0x6;
+	else if (dgain <= 0x782 && dgain >= 0x551)
+		offset = 0x3;
+	else if (dgain <= 0x550 && dgain >= 0x3c4)
+		offset = 0x0;
+	else if (dgain <= 0x3c3 && dgain >= 0x2aa)
+		offset = -3;
+	else if (dgain <= 0x2a9 && dgain >= 0x1e3)
+		offset = -6;
+	else if (dgain <= 0x1e2 && dgain >= 0x156)
+		offset = -9;
+	else if (dgain <= 0x155)
+		offset = -12;
+	else
+		offset = 0x0;
+
+	return offset;
+}
+
+static u8 _dpk_gainloss_read(struct rtw89_dev *rtwdev)
+{
+	rtw89_phy_write32_mask(rtwdev, R_KIP_RPT1, B_KIP_RPT1_SEL, 0x6);
+	rtw89_phy_write32_mask(rtwdev, R_DPK_CFG2, B_DPK_CFG2_ST, 0x1);
+	return rtw89_phy_read32_mask(rtwdev, R_RPT_COM, B_PRT_COM_GL);
+}
+
+static void _dpk_gainloss(struct rtw89_dev *rtwdev,
+			  enum rtw89_phy_idx phy, enum rtw89_rf_path path,
+			  u8 kidx)
+{
+	_dpk_table_select(rtwdev, path, kidx, 1);
+	_dpk_one_shot(rtwdev, phy, path, GAIN_LOSS);
+}
+
+#define DPK_TXAGC_LOWER 0x2e
+#define DPK_TXAGC_UPPER 0x3f
+#define DPK_TXAGC_INVAL 0xff
+
+static u8 _dpk_set_offset(struct rtw89_dev *rtwdev,
+			  enum rtw89_rf_path path, s8 gain_offset)
+{
+	u8 txagc;
+
+	txagc = (u8)rtw89_read_rf(rtwdev, path, RR_MODOPT, RFREG_MASK);
+
+	if (txagc - gain_offset < DPK_TXAGC_LOWER)
+		txagc = DPK_TXAGC_LOWER;
+	else if (txagc - gain_offset > DPK_TXAGC_UPPER)
+		txagc = DPK_TXAGC_UPPER;
+	else
+		txagc = txagc - gain_offset;
+
+	rtw89_write_rf(rtwdev, path, RR_MODOPT, RFREG_MASK, txagc);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] tmp_txagc (GL=%d) = 0x%x\n",
+		    gain_offset, txagc);
+	return txagc;
+}
+
+enum dpk_agc_step {
+	DPK_AGC_STEP_SYNC_DGAIN,
+	DPK_AGC_STEP_GAIN_ADJ,
+	DPK_AGC_STEP_GAIN_LOSS_IDX,
+	DPK_AGC_STEP_GL_GT_CRITERION,
+	DPK_AGC_STEP_GL_LT_CRITERION,
+	DPK_AGC_STEP_SET_TX_GAIN,
+};
+
+static u8 _dpk_pas_read(struct rtw89_dev *rtwdev, bool is_check)
+{
+	u32 val1_i = 0, val1_q = 0, val2_i = 0, val2_q = 0;
+	u8 i;
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_rfk_dpk_pas_read_defs_tbl);
+
+	if (is_check) {
+		rtw89_phy_write32_mask(rtwdev, R_DPK_CFG3, MASKBYTE3, 0x00);
+		val1_i = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKHWORD);
+		val1_i = abs(sign_extend32(val1_i, 11));
+		val1_q = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKLWORD);
+		val1_q = abs(sign_extend32(val1_q, 11));
+		rtw89_phy_write32_mask(rtwdev, R_DPK_CFG3, MASKBYTE3, 0x1f);
+		val2_i = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKHWORD);
+		val2_i = abs(sign_extend32(val2_i, 11));
+		val2_q = rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKLWORD);
+		val2_q = abs(sign_extend32(val2_q, 11));
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] PAS_delta = 0x%x\n",
+			    (val1_i * val1_i + val1_q * val1_q) /
+			    (val2_i * val2_i + val2_q * val2_q));
+
+	} else {
+		for (i = 0; i < 32; i++) {
+			rtw89_phy_write32_mask(rtwdev, R_DPK_CFG3, MASKBYTE3, i);
+			rtw89_debug(rtwdev, RTW89_DBG_RFK,
+				    "[DPK] PAS_Read[%02d]= 0x%08x\n", i,
+				    rtw89_phy_read32_mask(rtwdev, R_RPT_COM, MASKDWORD));
+		}
+	}
+	if ((val1_i * val1_i + val1_q * val1_q) >=
+	    ((val2_i * val2_i + val2_q * val2_q) * 8 / 5))
+		return 1;
+	else
+		return 0;
+}
+
+static u8 _dpk_agc(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+		   enum rtw89_rf_path path, u8 kidx, u8 init_txagc,
+		   bool loss_only)
+{
+#define DPK_AGC_ADJ_LMT 6
+#define DPK_DGAIN_UPPER 1922
+#define DPK_DGAIN_LOWER 342
+#define DPK_RXBB_UPPER 0x1f
+#define DPK_RXBB_LOWER 0
+#define DPK_GL_CRIT 7
+	u8 tmp_txagc, tmp_rxbb = 0, tmp_gl_idx = 0;
+	u8 agc_cnt = 0;
+	bool limited_rxbb = false;
+	s8 offset = 0;
+	u16 dgain = 0;
+	u8 step = DPK_AGC_STEP_SYNC_DGAIN;
+	bool goout = false;
+
+	tmp_txagc = init_txagc;
+
+	do {
+		switch (step) {
+		case DPK_AGC_STEP_SYNC_DGAIN:
+			if (_dpk_sync(rtwdev, phy, path, kidx)) {
+				tmp_txagc = DPK_TXAGC_INVAL;
+				goout = true;
+				break;
+			}
+
+			dgain = _dpk_dgain_read(rtwdev);
+
+			if (loss_only || limited_rxbb)
+				step = DPK_AGC_STEP_GAIN_LOSS_IDX;
+			else
+				step = DPK_AGC_STEP_GAIN_ADJ;
+			break;
+
+		case DPK_AGC_STEP_GAIN_ADJ:
+			tmp_rxbb = (u8)rtw89_read_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXBB);
+			offset = _dpk_dgain_mapping(rtwdev, dgain);
+
+			if (tmp_rxbb + offset > DPK_RXBB_UPPER) {
+				tmp_rxbb = DPK_RXBB_UPPER;
+				limited_rxbb = true;
+			} else if (tmp_rxbb + offset < DPK_RXBB_LOWER) {
+				tmp_rxbb = DPK_RXBB_LOWER;
+				limited_rxbb = true;
+			} else {
+				tmp_rxbb = tmp_rxbb + offset;
+			}
+
+			rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_M_RXBB, tmp_rxbb);
+			rtw89_debug(rtwdev, RTW89_DBG_RFK,
+				    "[DPK] Adjust RXBB (%d) = 0x%x\n", offset,
+				    tmp_rxbb);
+			if (offset != 0 || agc_cnt == 0) {
+				if (rtwdev->hal.current_band_width < RTW89_CHANNEL_WIDTH_80)
+					_dpk_bypass_rxcfir(rtwdev, path, true);
+				else
+					_dpk_lbk_rxiqk(rtwdev, phy, path);
+			}
+			if (dgain > DPK_DGAIN_UPPER || dgain < DPK_DGAIN_LOWER)
+				step = DPK_AGC_STEP_SYNC_DGAIN;
+			else
+				step = DPK_AGC_STEP_GAIN_LOSS_IDX;
+
+			agc_cnt++;
+			break;
+
+		case DPK_AGC_STEP_GAIN_LOSS_IDX:
+			_dpk_gainloss(rtwdev, phy, path, kidx);
+			tmp_gl_idx = _dpk_gainloss_read(rtwdev);
+
+			if ((tmp_gl_idx == 0 && _dpk_pas_read(rtwdev, true)) ||
+			    tmp_gl_idx > DPK_GL_CRIT)
+				step = DPK_AGC_STEP_GL_GT_CRITERION;
+			else if (tmp_gl_idx == 0)
+				step = DPK_AGC_STEP_GL_LT_CRITERION;
+			else
+				step = DPK_AGC_STEP_SET_TX_GAIN;
+			break;
+
+		case DPK_AGC_STEP_GL_GT_CRITERION:
+			if (tmp_txagc == DPK_TXAGC_LOWER) {
+				goout = true;
+				rtw89_debug(rtwdev, RTW89_DBG_RFK,
+					    "[DPK] Txagc at lower bound!!\n");
+			} else {
+				tmp_txagc = _dpk_set_offset(rtwdev, path, 3);
+			}
+			step = DPK_AGC_STEP_GAIN_LOSS_IDX;
+			agc_cnt++;
+			break;
+
+		case DPK_AGC_STEP_GL_LT_CRITERION:
+			if (tmp_txagc == DPK_TXAGC_UPPER) {
+				goout = true;
+				rtw89_debug(rtwdev, RTW89_DBG_RFK,
+					    "[DPK] Txagc at upper bound!!\n");
+			} else {
+				tmp_txagc = _dpk_set_offset(rtwdev, path, -2);
+			}
+			step = DPK_AGC_STEP_GAIN_LOSS_IDX;
+			agc_cnt++;
+			break;
+
+		case DPK_AGC_STEP_SET_TX_GAIN:
+			tmp_txagc = _dpk_set_offset(rtwdev, path, tmp_gl_idx);
+			goout = true;
+			agc_cnt++;
+			break;
+
+		default:
+			goout = true;
+			break;
+		}
+	} while (!goout && (agc_cnt < DPK_AGC_ADJ_LMT));
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] Txagc / RXBB for DPK = 0x%x / 0x%x\n", tmp_txagc,
+		    tmp_rxbb);
+
+	return tmp_txagc;
+}
+
+static void _dpk_set_mdpd_para(struct rtw89_dev *rtwdev, u8 order)
+{
+	switch (order) {
+	case 0:
+		rtw89_phy_write32_mask(rtwdev, R_LDL_NORM, B_LDL_NORM_OP, order);
+		rtw89_phy_write32_mask(rtwdev, R_LDL_NORM, B_LDL_NORM_PN, 0x3);
+		rtw89_phy_write32_mask(rtwdev, R_MDPK_SYNC, B_MDPK_SYNC_MAN, 0x1);
+		break;
+	case 1:
+		rtw89_phy_write32_mask(rtwdev, R_LDL_NORM, B_LDL_NORM_OP, order);
+		rtw89_phy_write32_clr(rtwdev, R_LDL_NORM, B_LDL_NORM_PN);
+		rtw89_phy_write32_clr(rtwdev, R_MDPK_SYNC, B_MDPK_SYNC_MAN);
+		break;
+	case 2:
+		rtw89_phy_write32_mask(rtwdev, R_LDL_NORM, B_LDL_NORM_OP, order);
+		rtw89_phy_write32_clr(rtwdev, R_LDL_NORM, B_LDL_NORM_PN);
+		rtw89_phy_write32_clr(rtwdev, R_MDPK_SYNC, B_MDPK_SYNC_MAN);
+		break;
+	default:
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] Wrong MDPD order!!(0x%x)\n", order);
+		break;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] Set MDPD order to 0x%x for IDL\n", order);
+}
+
+static void _dpk_idl_mpa(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			 enum rtw89_rf_path path, u8 kidx, u8 gain)
+{
+	_dpk_set_mdpd_para(rtwdev, 0x0);
+	_dpk_table_select(rtwdev, path, kidx, 1);
+	_dpk_one_shot(rtwdev, phy, path, MDPK_IDL);
+}
+
+static void _dpk_fill_result(struct rtw89_dev *rtwdev,
+			     enum rtw89_rf_path path, u8 kidx, u8 gain,
+			     u8 txagc)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+
+	u16 pwsf = 0x78;
+	u8 gs = 0x5b;
+
+	rtw89_phy_write32_mask(rtwdev, R_COEF_SEL + (path << 8), B_COEF_SEL_MDPD, kidx);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] Fill txagc/ pwsf/ gs = 0x%x/ 0x%x/ 0x%x\n", txagc,
+		    pwsf, gs);
+
+	dpk->bp[path][kidx].txagc_dpk = txagc;
+	rtw89_phy_write32_mask(rtwdev, R_TXAGC_RFK + (path << 8),
+			       0x3F << ((gain << 3) + (kidx << 4)), txagc);
+
+	dpk->bp[path][kidx].pwsf = pwsf;
+	rtw89_phy_write32_mask(rtwdev, R_DPD_BND + (path << 8) + (kidx << 2),
+			       0x1FF << (gain << 4), pwsf);
+
+	rtw89_phy_write32_mask(rtwdev, R_LOAD_COEF + (path << 8), B_LOAD_COEF_MDPD, 0x1);
+	rtw89_phy_write32_clr(rtwdev, R_LOAD_COEF + (path << 8), B_LOAD_COEF_MDPD);
+
+	dpk->bp[path][kidx].gs = gs;
+	rtw89_phy_write32_mask(rtwdev, R_DPD_CH0A + (path << 8) + (kidx << 2),
+			       MASKDWORD, 0x065b5b5b);
+
+	rtw89_phy_write32_clr(rtwdev, R_DPD_V1 + (path << 8), MASKDWORD);
+
+	rtw89_phy_write32_clr(rtwdev, R_MDPK_SYNC, B_MDPK_SYNC_SEL);
+}
+
+static bool _dpk_reload_check(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			      enum rtw89_rf_path path)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	bool is_reload = false;
+	u8 idx, cur_band, cur_ch;
+
+	cur_band = rtwdev->hal.current_band_type;
+	cur_ch = rtwdev->hal.current_channel;
+
+	for (idx = 0; idx < RTW89_DPK_BKUP_NUM; idx++) {
+		if (cur_band != dpk->bp[path][idx].band ||
+		    cur_ch != dpk->bp[path][idx].ch)
+			continue;
+
+		rtw89_phy_write32_mask(rtwdev, R_COEF_SEL + (path << 8),
+				       B_COEF_SEL_MDPD, idx);
+		dpk->cur_idx[path] = idx;
+		is_reload = true;
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] reload S%d[%d] success\n", path, idx);
+	}
+
+	return is_reload;
+}
+
+static bool _dpk_main(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+		      enum rtw89_rf_path path, u8 gain)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	u8 txagc = 0, kidx = dpk->cur_idx[path];
+	bool is_fail = false;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] ========= S%d[%d] DPK Start =========\n", path,
+		    kidx);
+
+	_rf_direct_cntrl(rtwdev, path, false);
+	txagc = _dpk_set_tx_pwr(rtwdev, gain, path);
+	_dpk_rf_setting(rtwdev, gain, path, kidx);
+	_dpk_rx_dck(rtwdev, phy, path);
+
+	_dpk_kip_setting(rtwdev, path, kidx);
+	_dpk_manual_txcfir(rtwdev, path, true);
+	txagc = _dpk_agc(rtwdev, phy, path, kidx, txagc, false);
+	if (txagc == DPK_TXAGC_INVAL)
+		is_fail = true;
+	_dpk_get_thermal(rtwdev, kidx, path);
+
+	_dpk_idl_mpa(rtwdev, phy, path, kidx, gain);
+	rtw89_write_rf(rtwdev, path, RR_MOD, RR_MOD_MASK, RR_MOD_V_RX);
+	_dpk_fill_result(rtwdev, path, kidx, gain, txagc);
+	_dpk_manual_txcfir(rtwdev, path, false);
+
+	if (!is_fail)
+		dpk->bp[path][kidx].path_ok = true;
+	else
+		dpk->bp[path][kidx].path_ok = false;
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] S%d[%d] DPK %s\n", path, kidx,
+		    is_fail ? "Check" : "Success");
+
+	return is_fail;
+}
+
+static void _dpk_cal_select(struct rtw89_dev *rtwdev, bool force,
+			    enum rtw89_phy_idx phy, u8 kpath)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	u32 backup_bb_val[BACKUP_BB_REGS_NR];
+	u32 backup_rf_val[RTW8852A_DPK_RF_PATH][BACKUP_RF_REGS_NR];
+	u32 kip_bkup[RTW8852A_DPK_RF_PATH][RTW8852A_DPK_KIP_REG_NUM] = {{0}};
+	u32 kip_reg[] = {R_RXIQC, R_IQK_RES};
+	u8 path;
+	bool is_fail = true, reloaded[RTW8852A_DPK_RF_PATH] = {false};
+
+	if (dpk->is_dpk_reload_en) {
+		for (path = 0; path < RTW8852A_DPK_RF_PATH; path++) {
+			if (!(kpath & BIT(path)))
+				continue;
+
+			reloaded[path] = _dpk_reload_check(rtwdev, phy, path);
+			if (!reloaded[path] && dpk->bp[path][0].ch != 0)
+				dpk->cur_idx[path] = !dpk->cur_idx[path];
+			else
+				_dpk_onoff(rtwdev, path, false);
+		}
+	} else {
+		for (path = 0; path < RTW8852A_DPK_RF_PATH; path++)
+			dpk->cur_idx[path] = 0;
+	}
+
+	if ((kpath == RF_A && reloaded[RF_PATH_A]) ||
+	    (kpath == RF_B && reloaded[RF_PATH_B]) ||
+	    (kpath == RF_AB && reloaded[RF_PATH_A] && reloaded[RF_PATH_B]))
+		return;
+
+	_rfk_backup_bb_reg(rtwdev, &backup_bb_val[0]);
+
+	for (path = 0; path < RTW8852A_DPK_RF_PATH; path++) {
+		if (!(kpath & BIT(path)) || reloaded[path])
+			continue;
+		if (rtwdev->is_tssi_mode[path])
+			_dpk_tssi_pause(rtwdev, path, true);
+		_dpk_bkup_kip(rtwdev, kip_reg, kip_bkup, path);
+		_rfk_backup_rf_reg(rtwdev, &backup_rf_val[path][0], path);
+		_dpk_information(rtwdev, phy, path);
+	}
+
+	_dpk_bb_afe_setting(rtwdev, phy, path, kpath);
+
+	for (path = 0; path < RTW8852A_DPK_RF_PATH; path++) {
+		if (!(kpath & BIT(path)) || reloaded[path])
+			continue;
+
+		is_fail = _dpk_main(rtwdev, phy, path, 1);
+		_dpk_onoff(rtwdev, path, is_fail);
+	}
+
+	_dpk_bb_afe_restore(rtwdev, phy, path, kpath);
+	_rfk_restore_bb_reg(rtwdev, &backup_bb_val[0]);
+
+	for (path = 0; path < RTW8852A_DPK_RF_PATH; path++) {
+		if (!(kpath & BIT(path)) || reloaded[path])
+			continue;
+
+		_dpk_kip_restore(rtwdev, path);
+		_dpk_reload_kip(rtwdev, kip_reg, kip_bkup, path);
+		_rfk_restore_rf_reg(rtwdev, &backup_rf_val[path][0], path);
+		if (rtwdev->is_tssi_mode[path])
+			_dpk_tssi_pause(rtwdev, path, false);
+	}
+}
+
+static bool _dpk_bypass_check(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	struct rtw89_fem_info *fem = &rtwdev->fem;
+
+	if (fem->epa_2g && rtwdev->hal.current_band_type == RTW89_BAND_2G) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] Skip DPK due to 2G_ext_PA exist!!\n");
+		return true;
+	} else if (fem->epa_5g && rtwdev->hal.current_band_type == RTW89_BAND_5G) {
+		rtw89_debug(rtwdev, RTW89_DBG_RFK,
+			    "[DPK] Skip DPK due to 5G_ext_PA exist!!\n");
+		return true;
+	}
+
+	return false;
+}
+
+static void _dpk_force_bypass(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	u8 path, kpath;
+
+	kpath = _kpath(rtwdev, phy);
+
+	for (path = 0; path < RTW8852A_DPK_RF_PATH; path++) {
+		if (kpath & BIT(path))
+			_dpk_onoff(rtwdev, path, true);
+	}
+}
+
+static void _dpk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy, bool force)
+{
+	rtw89_debug(rtwdev, RTW89_DBG_RFK,
+		    "[DPK] ****** DPK Start (Ver: 0x%x, Cv: %d, RF_para: %d) ******\n",
+		    RTW8852A_DPK_VER, rtwdev->hal.cv,
+		    RTW8852A_RF_REL_VERSION);
+
+	if (_dpk_bypass_check(rtwdev, phy))
+		_dpk_force_bypass(rtwdev, phy);
+	else
+		_dpk_cal_select(rtwdev, force, phy, _kpath(rtwdev, phy));
+}
+
+static void _dpk_onoff(struct rtw89_dev *rtwdev,
+		       enum rtw89_rf_path path, bool off)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	u8 val, kidx = dpk->cur_idx[path];
+
+	val = dpk->is_dpk_enable && !off && dpk->bp[path][kidx].path_ok;
+
+	rtw89_phy_write32_mask(rtwdev, R_DPD_CH0A + (path << 8) + (kidx << 2),
+			       MASKBYTE3, 0x6 | val);
+
+	rtw89_debug(rtwdev, RTW89_DBG_RFK, "[DPK] S%d[%d] DPK %s !!!\n", path,
+		    kidx, dpk->is_dpk_enable && !off ? "enable" : "disable");
+}
+
+static void _dpk_track(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_dpk_info *dpk = &rtwdev->dpk;
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 path, kidx;
+	u8 trk_idx = 0, txagc_rf = 0;
+	s8 txagc_bb = 0, txagc_bb_tp = 0, ini_diff = 0, txagc_ofst = 0;
+	u16 pwsf[2];
+	u8 cur_ther;
+	s8 delta_ther[2] = {0};
+
+	for (path = 0; path < RTW8852A_DPK_RF_PATH; path++) {
+		kidx = dpk->cur_idx[path];
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+			    "[DPK_TRK] ================[S%d[%d] (CH %d)]================\n",
+			    path, kidx, dpk->bp[path][kidx].ch);
+
+		cur_ther = ewma_thermal_read(&rtwdev->phystat.avg_thermal[path]);
+
+		rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+			    "[DPK_TRK] thermal now = %d\n", cur_ther);
+
+		if (dpk->bp[path][kidx].ch != 0 && cur_ther != 0)
+			delta_ther[path] = dpk->bp[path][kidx].ther_dpk - cur_ther;
+
+		if (dpk->bp[path][kidx].band == RTW89_BAND_2G)
+			delta_ther[path] = delta_ther[path] * 3 / 2;
+		else
+			delta_ther[path] = delta_ther[path] * 5 / 2;
+
+		txagc_rf = (u8)rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB  + (path << 13),
+						     RR_MODOPT_M_TXPWR);
+
+		if (rtwdev->is_tssi_mode[path]) {
+			trk_idx = (u8)rtw89_read_rf(rtwdev, path, RR_TXA, RR_TXA_TRK);
+
+			rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+				    "[DPK_TRK] txagc_RF / track_idx = 0x%x / %d\n",
+				    txagc_rf, trk_idx);
+
+			txagc_bb =
+				(s8)rtw89_phy_read32_mask(rtwdev,
+							  R_TXAGC_BB + (path << 13),
+							  MASKBYTE2);
+			txagc_bb_tp =
+				(u8)rtw89_phy_read32_mask(rtwdev,
+							  R_TXAGC_TP + (path << 13),
+							  B_TXAGC_TP);
+
+			rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+				    "[DPK_TRK] txagc_bb_tp / txagc_bb = 0x%x / 0x%x\n",
+				    txagc_bb_tp, txagc_bb);
+
+			txagc_ofst =
+				(s8)rtw89_phy_read32_mask(rtwdev,
+							  R_TXAGC_BB + (path << 13),
+							  MASKBYTE3);
+
+			rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+				    "[DPK_TRK] txagc_offset / delta_ther = %d / %d\n",
+				    txagc_ofst, delta_ther[path]);
+
+			if (rtw89_phy_read32_mask(rtwdev, R_DPD_COM + (path << 8),
+						  BIT(15)) == 0x1)
+				txagc_ofst = 0;
+
+			if (txagc_rf != 0 && cur_ther != 0)
+				ini_diff = txagc_ofst + delta_ther[path];
+
+			if (rtw89_phy_read32_mask(rtwdev, R_P0_TXDPD + (path << 13),
+						  B_P0_TXDPD) == 0x0) {
+				pwsf[0] = dpk->bp[path][kidx].pwsf + txagc_bb_tp -
+					  txagc_bb + ini_diff +
+					  tssi_info->extra_ofst[path];
+				pwsf[1] = dpk->bp[path][kidx].pwsf + txagc_bb_tp -
+					  txagc_bb + ini_diff +
+					  tssi_info->extra_ofst[path];
+			} else {
+				pwsf[0] = dpk->bp[path][kidx].pwsf + ini_diff +
+					  tssi_info->extra_ofst[path];
+				pwsf[1] = dpk->bp[path][kidx].pwsf + ini_diff +
+					  tssi_info->extra_ofst[path];
+			}
+
+		} else {
+			pwsf[0] = (dpk->bp[path][kidx].pwsf + delta_ther[path]) & 0x1ff;
+			pwsf[1] = (dpk->bp[path][kidx].pwsf + delta_ther[path]) & 0x1ff;
+		}
+
+		if (rtw89_phy_read32_mask(rtwdev, R_DPK_TRK, B_DPK_TRK_DIS) == 0x0 &&
+		    txagc_rf != 0) {
+			rtw89_debug(rtwdev, RTW89_DBG_RFK_TRACK,
+				    "[DPK_TRK] New pwsf[0] / pwsf[1] = 0x%x / 0x%x\n",
+				    pwsf[0], pwsf[1]);
+
+			rtw89_phy_write32_mask(rtwdev, R_DPD_BND + (path << 8) + (kidx << 2),
+					       0x000001FF, pwsf[0]);
+			rtw89_phy_write32_mask(rtwdev, R_DPD_BND + (path << 8) + (kidx << 2),
+					       0x01FF0000, pwsf[1]);
+		}
+	}
+}
+
+static void _tssi_rf_setting(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			     enum rtw89_rf_path path)
+{
+	enum rtw89_band band = rtwdev->hal.current_band_type;
+
+	if (band == RTW89_BAND_2G)
+		rtw89_write_rf(rtwdev, path, RR_TXPOW, RR_TXPOW_TXG, 0x1);
+	else
+		rtw89_write_rf(rtwdev, path, RR_TXPOW, RR_TXPOW_TXA, 0x1);
+}
+
+static void _tssi_set_sys(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	enum rtw89_band band = rtwdev->hal.current_band_type;
+
+	rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_sys_defs_tbl);
+	rtw89_rfk_parser_by_cond(rtwdev, band == RTW89_BAND_2G,
+				 &rtw8852a_tssi_sys_defs_2g_tbl,
+				 &rtw8852a_tssi_sys_defs_5g_tbl);
+}
+
+static void _tssi_ini_txpwr_ctrl_bb(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+				    enum rtw89_rf_path path)
+{
+	enum rtw89_band band = rtwdev->hal.current_band_type;
+
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_txpwr_ctrl_bb_defs_a_tbl,
+				 &rtw8852a_tssi_txpwr_ctrl_bb_defs_b_tbl);
+	rtw89_rfk_parser_by_cond(rtwdev, band == RTW89_BAND_2G,
+				 &rtw8852a_tssi_txpwr_ctrl_bb_defs_2g_tbl,
+				 &rtw8852a_tssi_txpwr_ctrl_bb_defs_5g_tbl);
+}
+
+static void _tssi_ini_txpwr_ctrl_bb_he_tb(struct rtw89_dev *rtwdev,
+					  enum rtw89_phy_idx phy,
+					  enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_a_tbl,
+				 &rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_b_tbl);
+}
+
+static void _tssi_set_dck(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			  enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_dck_defs_a_tbl,
+				 &rtw8852a_tssi_dck_defs_b_tbl);
+}
+
+static void _tssi_set_tmeter_tbl(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+				 enum rtw89_rf_path path)
+{
+#define __get_val(ptr, idx)				\
+({							\
+	s8 *__ptr = (ptr);				\
+	u8 __idx = (idx), __i, __v;			\
+	u32 __val = 0;					\
+	for (__i = 0; __i < 4; __i++) {			\
+		__v = (__ptr[__idx + __i]);		\
+		__val |= (__v << (8 * __i));		\
+	}						\
+	__val;						\
+})
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 ch = rtwdev->hal.current_channel;
+	u8 subband = rtwdev->hal.current_subband;
+	const u8 *thm_up_a = NULL;
+	const u8 *thm_down_a = NULL;
+	const u8 *thm_up_b = NULL;
+	const u8 *thm_down_b = NULL;
+	u8 thermal = 0xff;
+	s8 thm_ofst[64] = {0};
+	u32 tmp = 0;
+	u8 i, j;
+
+	switch (subband) {
+	case RTW89_CH_2G:
+		thm_up_a = rtw89_8852a_trk_cfg.delta_swingidx_2ga_p;
+		thm_down_a = rtw89_8852a_trk_cfg.delta_swingidx_2ga_n;
+		thm_up_b = rtw89_8852a_trk_cfg.delta_swingidx_2gb_p;
+		thm_down_b = rtw89_8852a_trk_cfg.delta_swingidx_2gb_n;
+		break;
+	case RTW89_CH_5G_BAND_1:
+		thm_up_a = rtw89_8852a_trk_cfg.delta_swingidx_5ga_p[0];
+		thm_down_a = rtw89_8852a_trk_cfg.delta_swingidx_5ga_n[0];
+		thm_up_b = rtw89_8852a_trk_cfg.delta_swingidx_5gb_p[0];
+		thm_down_b = rtw89_8852a_trk_cfg.delta_swingidx_5gb_n[0];
+		break;
+	case RTW89_CH_5G_BAND_3:
+		thm_up_a = rtw89_8852a_trk_cfg.delta_swingidx_5ga_p[1];
+		thm_down_a = rtw89_8852a_trk_cfg.delta_swingidx_5ga_n[1];
+		thm_up_b = rtw89_8852a_trk_cfg.delta_swingidx_5gb_p[1];
+		thm_down_b = rtw89_8852a_trk_cfg.delta_swingidx_5gb_n[1];
+		break;
+	case RTW89_CH_5G_BAND_4:
+		thm_up_a = rtw89_8852a_trk_cfg.delta_swingidx_5ga_p[2];
+		thm_down_a = rtw89_8852a_trk_cfg.delta_swingidx_5ga_n[2];
+		thm_up_b = rtw89_8852a_trk_cfg.delta_swingidx_5gb_p[2];
+		thm_down_b = rtw89_8852a_trk_cfg.delta_swingidx_5gb_n[2];
+		break;
+	}
+
+	if (path == RF_PATH_A) {
+		thermal = tssi_info->thermal[RF_PATH_A];
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI] ch=%d thermal_pathA=0x%x\n", ch, thermal);
+
+		rtw89_phy_write32_mask(rtwdev, R_P0_TMETER, B_P0_TMETER_DIS, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_P0_TMETER, B_P0_TMETER_TRK, 0x1);
+
+		if (thermal == 0xff) {
+			rtw89_phy_write32_mask(rtwdev, R_P0_TMETER, B_P0_TMETER, 32);
+			rtw89_phy_write32_mask(rtwdev, R_P0_RFCTM, B_P0_RFCTM_VAL, 32);
+
+			for (i = 0; i < 64; i += 4) {
+				rtw89_phy_write32(rtwdev, R_P0_TSSI_BASE + i, 0x0);
+
+				rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+					    "[TSSI] write 0x%x val=0x%08x\n",
+					    0x5c00 + i, 0x0);
+			}
+
+		} else {
+			rtw89_phy_write32_mask(rtwdev, R_P0_TMETER, B_P0_TMETER, thermal);
+			rtw89_phy_write32_mask(rtwdev, R_P0_RFCTM, B_P0_RFCTM_VAL,
+					       thermal);
+
+			i = 0;
+			for (j = 0; j < 32; j++)
+				thm_ofst[j] = i < DELTA_SWINGIDX_SIZE ?
+					      -thm_down_a[i++] :
+					      -thm_down_a[DELTA_SWINGIDX_SIZE - 1];
+
+			i = 1;
+			for (j = 63; j >= 32; j--)
+				thm_ofst[j] = i < DELTA_SWINGIDX_SIZE ?
+					      thm_up_a[i++] :
+					      thm_up_a[DELTA_SWINGIDX_SIZE - 1];
+
+			for (i = 0; i < 64; i += 4) {
+				tmp = __get_val(thm_ofst, i);
+				rtw89_phy_write32(rtwdev, R_P0_TSSI_BASE + i, tmp);
+
+				rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+					    "[TSSI] write 0x%x val=0x%08x\n",
+					    0x5c00 + i, tmp);
+			}
+		}
+		rtw89_phy_write32_mask(rtwdev, R_P0_RFCTM, R_P0_RFCTM_RDY, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_P0_RFCTM, R_P0_RFCTM_RDY, 0x0);
+
+	} else {
+		thermal = tssi_info->thermal[RF_PATH_B];
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI] ch=%d thermal_pathB=0x%x\n", ch, thermal);
+
+		rtw89_phy_write32_mask(rtwdev, R_P1_TMETER, B_P1_TMETER_DIS, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_P1_TMETER, B_P1_TMETER_TRK, 0x1);
+
+		if (thermal == 0xff) {
+			rtw89_phy_write32_mask(rtwdev, R_P1_TMETER, B_P1_TMETER, 32);
+			rtw89_phy_write32_mask(rtwdev, R_P1_RFCTM, B_P1_RFCTM_VAL, 32);
+
+			for (i = 0; i < 64; i += 4) {
+				rtw89_phy_write32(rtwdev, R_TSSI_THOF + i, 0x0);
+
+				rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+					    "[TSSI] write 0x%x val=0x%08x\n",
+					    0x7c00 + i, 0x0);
+			}
+
+		} else {
+			rtw89_phy_write32_mask(rtwdev, R_P1_TMETER, B_P1_TMETER, thermal);
+			rtw89_phy_write32_mask(rtwdev, R_P1_RFCTM, B_P1_RFCTM_VAL,
+					       thermal);
+
+			i = 0;
+			for (j = 0; j < 32; j++)
+				thm_ofst[j] = i < DELTA_SWINGIDX_SIZE ?
+					      -thm_down_b[i++] :
+					      -thm_down_b[DELTA_SWINGIDX_SIZE - 1];
+
+			i = 1;
+			for (j = 63; j >= 32; j--)
+				thm_ofst[j] = i < DELTA_SWINGIDX_SIZE ?
+					      thm_up_b[i++] :
+					      thm_up_b[DELTA_SWINGIDX_SIZE - 1];
+
+			for (i = 0; i < 64; i += 4) {
+				tmp = __get_val(thm_ofst, i);
+				rtw89_phy_write32(rtwdev, R_TSSI_THOF + i, tmp);
+
+				rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+					    "[TSSI] write 0x%x val=0x%08x\n",
+					    0x7c00 + i, tmp);
+			}
+		}
+		rtw89_phy_write32_mask(rtwdev, R_P1_RFCTM, R_P1_RFCTM_RDY, 0x1);
+		rtw89_phy_write32_mask(rtwdev, R_P1_RFCTM, R_P1_RFCTM_RDY, 0x0);
+	}
+#undef __get_val
+}
+
+static void _tssi_set_dac_gain_tbl(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+				   enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_dac_gain_tbl_defs_a_tbl,
+				 &rtw8852a_tssi_dac_gain_tbl_defs_b_tbl);
+}
+
+static void _tssi_slope_cal_org(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+				enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_slope_cal_org_defs_a_tbl,
+				 &rtw8852a_tssi_slope_cal_org_defs_b_tbl);
+}
+
+static void _tssi_set_rf_gap_tbl(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+				 enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_rf_gap_tbl_defs_a_tbl,
+				 &rtw8852a_tssi_rf_gap_tbl_defs_b_tbl);
+}
+
+static void _tssi_set_slope(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			    enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_slope_defs_a_tbl,
+				 &rtw8852a_tssi_slope_defs_b_tbl);
+}
+
+static void _tssi_set_track(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			    enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_track_defs_a_tbl,
+				 &rtw8852a_tssi_track_defs_b_tbl);
+}
+
+static void _tssi_set_txagc_offset_mv_avg(struct rtw89_dev *rtwdev,
+					  enum rtw89_phy_idx phy,
+					  enum rtw89_rf_path path)
+{
+	rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+				 &rtw8852a_tssi_txagc_ofst_mv_avg_defs_a_tbl,
+				 &rtw8852a_tssi_txagc_ofst_mv_avg_defs_b_tbl);
+}
+
+static void _tssi_pak(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+		      enum rtw89_rf_path path)
+{
+	u8 subband = rtwdev->hal.current_subband;
+
+	switch (subband) {
+	case RTW89_CH_2G:
+		rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+					 &rtw8852a_tssi_pak_defs_a_2g_tbl,
+					 &rtw8852a_tssi_pak_defs_b_2g_tbl);
+		break;
+	case RTW89_CH_5G_BAND_1:
+		rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+					 &rtw8852a_tssi_pak_defs_a_5g_1_tbl,
+					 &rtw8852a_tssi_pak_defs_b_5g_1_tbl);
+		break;
+	case RTW89_CH_5G_BAND_3:
+		rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+					 &rtw8852a_tssi_pak_defs_a_5g_3_tbl,
+					 &rtw8852a_tssi_pak_defs_b_5g_3_tbl);
+		break;
+	case RTW89_CH_5G_BAND_4:
+		rtw89_rfk_parser_by_cond(rtwdev, path == RF_PATH_A,
+					 &rtw8852a_tssi_pak_defs_a_5g_4_tbl,
+					 &rtw8852a_tssi_pak_defs_b_5g_4_tbl);
+		break;
+	}
+}
+
+static void _tssi_enable(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 i;
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		_tssi_set_track(rtwdev, phy, i);
+		_tssi_set_txagc_offset_mv_avg(rtwdev, phy, i);
+
+		rtw89_rfk_parser_by_cond(rtwdev, i == RF_PATH_A,
+					 &rtw8852a_tssi_enable_defs_a_tbl,
+					 &rtw8852a_tssi_enable_defs_b_tbl);
+
+		tssi_info->base_thermal[i] =
+			ewma_thermal_read(&rtwdev->phystat.avg_thermal[i]);
+		rtwdev->is_tssi_mode[i] = true;
+	}
+}
+
+static void _tssi_disable(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_disable_defs_tbl);
+
+	rtwdev->is_tssi_mode[RF_PATH_A] = false;
+	rtwdev->is_tssi_mode[RF_PATH_B] = false;
+}
+
+static u32 _tssi_get_cck_group(struct rtw89_dev *rtwdev, u8 ch)
+{
+	switch (ch) {
+	case 1 ... 2:
+		return 0;
+	case 3 ... 5:
+		return 1;
+	case 6 ... 8:
+		return 2;
+	case 9 ... 11:
+		return 3;
+	case 12 ... 13:
+		return 4;
+	case 14:
+		return 5;
+	}
+
+	return 0;
+}
+
+#define TSSI_EXTRA_GROUP_BIT (BIT(31))
+#define TSSI_EXTRA_GROUP(idx) (TSSI_EXTRA_GROUP_BIT | (idx))
+#define IS_TSSI_EXTRA_GROUP(group) ((group) & TSSI_EXTRA_GROUP_BIT)
+#define TSSI_EXTRA_GET_GROUP_IDX1(group) ((group) & ~TSSI_EXTRA_GROUP_BIT)
+#define TSSI_EXTRA_GET_GROUP_IDX2(group) (TSSI_EXTRA_GET_GROUP_IDX1(group) + 1)
+
+static u32 _tssi_get_ofdm_group(struct rtw89_dev *rtwdev, u8 ch)
+{
+	switch (ch) {
+	case 1 ... 2:
+		return 0;
+	case 3 ... 5:
+		return 1;
+	case 6 ... 8:
+		return 2;
+	case 9 ... 11:
+		return 3;
+	case 12 ... 14:
+		return 4;
+	case 36 ... 40:
+		return 5;
+	case 41 ... 43:
+		return TSSI_EXTRA_GROUP(5);
+	case 44 ... 48:
+		return 6;
+	case 49 ... 51:
+		return TSSI_EXTRA_GROUP(6);
+	case 52 ... 56:
+		return 7;
+	case 57 ... 59:
+		return TSSI_EXTRA_GROUP(7);
+	case 60 ... 64:
+		return 8;
+	case 100 ... 104:
+		return 9;
+	case 105 ... 107:
+		return TSSI_EXTRA_GROUP(9);
+	case 108 ... 112:
+		return 10;
+	case 113 ... 115:
+		return TSSI_EXTRA_GROUP(10);
+	case 116 ... 120:
+		return 11;
+	case 121 ... 123:
+		return TSSI_EXTRA_GROUP(11);
+	case 124 ... 128:
+		return 12;
+	case 129 ... 131:
+		return TSSI_EXTRA_GROUP(12);
+	case 132 ... 136:
+		return 13;
+	case 137 ... 139:
+		return TSSI_EXTRA_GROUP(13);
+	case 140 ... 144:
+		return 14;
+	case 149 ... 153:
+		return 15;
+	case 154 ... 156:
+		return TSSI_EXTRA_GROUP(15);
+	case 157 ... 161:
+		return 16;
+	case 162 ... 164:
+		return TSSI_EXTRA_GROUP(16);
+	case 165 ... 169:
+		return 17;
+	case 170 ... 172:
+		return TSSI_EXTRA_GROUP(17);
+	case 173 ... 177:
+		return 18;
+	}
+
+	return 0;
+}
+
+static u32 _tssi_get_trim_group(struct rtw89_dev *rtwdev, u8 ch)
+{
+	switch (ch) {
+	case 1 ... 8:
+		return 0;
+	case 9 ... 14:
+		return 1;
+	case 36 ... 48:
+		return 2;
+	case 52 ... 64:
+		return 3;
+	case 100 ... 112:
+		return 4;
+	case 116 ... 128:
+		return 5;
+	case 132 ... 144:
+		return 6;
+	case 149 ... 177:
+		return 7;
+	}
+
+	return 0;
+}
+
+static s8 _tssi_get_ofdm_de(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			    enum rtw89_rf_path path)
+{
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 ch = rtwdev->hal.current_channel;
+	u32 gidx, gidx_1st, gidx_2nd;
+	s8 de_1st = 0;
+	s8 de_2nd = 0;
+	s8 val;
+
+	gidx = _tssi_get_ofdm_group(rtwdev, ch);
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+		    "[TSSI][TRIM]: path=%d mcs group_idx=0x%x\n",
+		    path, gidx);
+
+	if (IS_TSSI_EXTRA_GROUP(gidx)) {
+		gidx_1st = TSSI_EXTRA_GET_GROUP_IDX1(gidx);
+		gidx_2nd = TSSI_EXTRA_GET_GROUP_IDX2(gidx);
+		de_1st = tssi_info->tssi_mcs[path][gidx_1st];
+		de_2nd = tssi_info->tssi_mcs[path][gidx_2nd];
+		val = (de_1st + de_2nd) / 2;
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM]: path=%d mcs de=%d 1st=%d 2nd=%d\n",
+			    path, val, de_1st, de_2nd);
+	} else {
+		val = tssi_info->tssi_mcs[path][gidx];
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM]: path=%d mcs de=%d\n", path, val);
+	}
+
+	return val;
+}
+
+static s8 _tssi_get_ofdm_trim_de(struct rtw89_dev *rtwdev,
+				 enum rtw89_phy_idx phy,
+				 enum rtw89_rf_path path)
+{
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 ch = rtwdev->hal.current_channel;
+	u32 tgidx, tgidx_1st, tgidx_2nd;
+	s8 tde_1st = 0;
+	s8 tde_2nd = 0;
+	s8 val;
+
+	tgidx = _tssi_get_trim_group(rtwdev, ch);
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+		    "[TSSI][TRIM]: path=%d mcs trim_group_idx=0x%x\n",
+		    path, tgidx);
+
+	if (IS_TSSI_EXTRA_GROUP(tgidx)) {
+		tgidx_1st = TSSI_EXTRA_GET_GROUP_IDX1(tgidx);
+		tgidx_2nd = TSSI_EXTRA_GET_GROUP_IDX2(tgidx);
+		tde_1st = tssi_info->tssi_trim[path][tgidx_1st];
+		tde_2nd = tssi_info->tssi_trim[path][tgidx_2nd];
+		val = (tde_1st + tde_2nd) / 2;
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM]: path=%d mcs trim_de=%d 1st=%d 2nd=%d\n",
+			    path, val, tde_1st, tde_2nd);
+	} else {
+		val = tssi_info->tssi_trim[path][tgidx];
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM]: path=%d mcs trim_de=%d\n",
+			    path, val);
+	}
+
+	return val;
+}
+
+static void _tssi_set_efuse_to_de(struct rtw89_dev *rtwdev,
+				  enum rtw89_phy_idx phy)
+{
+#define __DE_MASK 0x003ff000
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	static const u32 r_cck_long[RF_PATH_NUM_8852A] = {0x5858, 0x7858};
+	static const u32 r_cck_short[RF_PATH_NUM_8852A] = {0x5860, 0x7860};
+	static const u32 r_mcs_20m[RF_PATH_NUM_8852A] = {0x5838, 0x7838};
+	static const u32 r_mcs_40m[RF_PATH_NUM_8852A] = {0x5840, 0x7840};
+	static const u32 r_mcs_80m[RF_PATH_NUM_8852A] = {0x5848, 0x7848};
+	static const u32 r_mcs_80m_80m[RF_PATH_NUM_8852A] = {0x5850, 0x7850};
+	static const u32 r_mcs_5m[RF_PATH_NUM_8852A] = {0x5828, 0x7828};
+	static const u32 r_mcs_10m[RF_PATH_NUM_8852A] = {0x5830, 0x7830};
+	u8 ch = rtwdev->hal.current_channel;
+	u8 i, gidx;
+	s8 ofdm_de;
+	s8 trim_de;
+	s32 val;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "[TSSI][TRIM]: phy=%d ch=%d\n",
+		    phy, ch);
+
+	for (i = 0; i < RF_PATH_NUM_8852A; i++) {
+		gidx = _tssi_get_cck_group(rtwdev, ch);
+		trim_de = _tssi_get_ofdm_trim_de(rtwdev, phy, i);
+		val = tssi_info->tssi_cck[i][gidx] + trim_de;
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM]: path=%d cck[%d]=0x%x trim=0x%x\n",
+			    i, gidx, tssi_info->tssi_cck[i][gidx], trim_de);
+
+		rtw89_phy_write32_mask(rtwdev, r_cck_long[i], __DE_MASK, val);
+		rtw89_phy_write32_mask(rtwdev, r_cck_short[i], __DE_MASK, val);
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI] Set TSSI CCK DE 0x%x[21:12]=0x%x\n",
+			    r_cck_long[i],
+			    rtw89_phy_read32_mask(rtwdev, r_cck_long[i],
+						  __DE_MASK));
+
+		ofdm_de = _tssi_get_ofdm_de(rtwdev, phy, i);
+		trim_de = _tssi_get_ofdm_trim_de(rtwdev, phy, i);
+		val = ofdm_de + trim_de;
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRIM]: path=%d mcs=0x%x trim=0x%x\n",
+			    i, ofdm_de, trim_de);
+
+		rtw89_phy_write32_mask(rtwdev, r_mcs_20m[i], __DE_MASK, val);
+		rtw89_phy_write32_mask(rtwdev, r_mcs_40m[i], __DE_MASK, val);
+		rtw89_phy_write32_mask(rtwdev, r_mcs_80m[i], __DE_MASK, val);
+		rtw89_phy_write32_mask(rtwdev, r_mcs_80m_80m[i], __DE_MASK, val);
+		rtw89_phy_write32_mask(rtwdev, r_mcs_5m[i], __DE_MASK, val);
+		rtw89_phy_write32_mask(rtwdev, r_mcs_10m[i], __DE_MASK, val);
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI] Set TSSI MCS DE 0x%x[21:12]=0x%x\n",
+			    r_mcs_20m[i],
+			    rtw89_phy_read32_mask(rtwdev, r_mcs_20m[i],
+						  __DE_MASK));
+	}
+#undef __DE_MASK
+}
+
+static void _tssi_track(struct rtw89_dev *rtwdev)
+{
+	static const u32 tx_gain_scale_table[] = {
+		0x400, 0x40e, 0x41d, 0x427, 0x43c, 0x44c, 0x45c, 0x46c,
+		0x400, 0x39d, 0x3ab, 0x3b8, 0x3c6, 0x3d4, 0x3e2, 0x3f1
+	};
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 path;
+	u8 cur_ther;
+	s32 delta_ther = 0, gain_offset_int, gain_offset_float;
+	s8 gain_offset;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "[TSSI][TRK] %s:\n",
+		    __func__);
+
+	if (!rtwdev->is_tssi_mode[RF_PATH_A])
+		return;
+	if (!rtwdev->is_tssi_mode[RF_PATH_B])
+		return;
+
+	for (path = RF_PATH_A; path < RF_PATH_NUM_8852A; path++) {
+		if (!tssi_info->tssi_tracking_check[path]) {
+			rtw89_debug(rtwdev, RTW89_DBG_TSSI, "[TSSI][TRK] return!!!\n");
+			continue;
+		}
+
+		cur_ther = (u8)rtw89_phy_read32_mask(rtwdev,
+						  R_TSSI_THER + (path << 13),
+						  B_TSSI_THER);
+
+		if (cur_ther == 0 || tssi_info->base_thermal[path] == 0)
+			continue;
+
+		delta_ther = cur_ther - tssi_info->base_thermal[path];
+
+		gain_offset = (s8)delta_ther * 15 / 10;
+
+		tssi_info->extra_ofst[path] = gain_offset;
+
+		rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+			    "[TSSI][TRK] base_thermal=%d gain_offset=0x%x path=%d\n",
+			    tssi_info->base_thermal[path], gain_offset, path);
+
+		gain_offset_int = gain_offset >> 3;
+		gain_offset_float = gain_offset & 7;
+
+		if (gain_offset_int > 15)
+			gain_offset_int = 15;
+		else if (gain_offset_int < -16)
+			gain_offset_int = -16;
+
+		rtw89_phy_write32_mask(rtwdev, R_DPD_OFT_EN + (path << 13),
+				       B_DPD_OFT_EN, 0x1);
+
+		rtw89_phy_write32_mask(rtwdev, R_TXGAIN_SCALE + (path << 13),
+				       B_TXGAIN_SCALE_EN, 0x1);
+
+		rtw89_phy_write32_mask(rtwdev, R_DPD_OFT_ADDR + (path << 13),
+				       B_DPD_OFT_ADDR, gain_offset_int);
+
+		rtw89_phy_write32_mask(rtwdev, R_TXGAIN_SCALE + (path << 13),
+				       B_TXGAIN_SCALE_OFT,
+				       tx_gain_scale_table[gain_offset_float]);
+	}
+}
+
+static void _tssi_high_power(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 ch = rtwdev->hal.current_channel, ch_tmp;
+	u8 bw = rtwdev->hal.current_band_width;
+	u8 subband = rtwdev->hal.current_subband;
+	s8 power;
+	s32 xdbm;
+
+	if (bw == RTW89_CHANNEL_WIDTH_40)
+		ch_tmp = ch - 2;
+	else if (bw == RTW89_CHANNEL_WIDTH_80)
+		ch_tmp = ch - 6;
+	else
+		ch_tmp = ch;
+
+	power = rtw89_phy_read_txpwr_limit(rtwdev, bw, RTW89_1TX,
+					   RTW89_RS_MCS, RTW89_NONBF, ch_tmp);
+
+	xdbm = power * 100 / 4;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "[TSSI] %s: phy=%d xdbm=%d\n",
+		    __func__, phy, xdbm);
+
+	if (xdbm > 1800 && subband == RTW89_CH_2G) {
+		tssi_info->tssi_tracking_check[RF_PATH_A] = true;
+		tssi_info->tssi_tracking_check[RF_PATH_B] = true;
+	} else {
+		rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_tracking_defs_tbl);
+		tssi_info->extra_ofst[RF_PATH_A] = 0;
+		tssi_info->extra_ofst[RF_PATH_B] = 0;
+		tssi_info->tssi_tracking_check[RF_PATH_A] = false;
+		tssi_info->tssi_tracking_check[RF_PATH_B] = false;
+	}
+}
+
+static void _tssi_hw_tx(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy,
+			u8 path, s16 pwr_dbm, u8 enable)
+{
+	rtw8852a_bb_set_plcp_tx(rtwdev);
+	rtw8852a_bb_cfg_tx_path(rtwdev, path);
+	rtw8852a_bb_set_power(rtwdev, pwr_dbm, phy);
+	rtw8852a_bb_set_pmac_pkt_tx(rtwdev, enable, 20, 5000, 0, phy);
+}
+
+static void _tssi_pre_tx(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	const struct rtw89_chip_info *mac_reg = rtwdev->chip;
+	u8 ch = rtwdev->hal.current_channel, ch_tmp;
+	u8 bw = rtwdev->hal.current_band_width;
+	u16 tx_en;
+	u8 phy_map = rtw89_btc_phymap(rtwdev, phy, 0);
+	s8 power;
+	s16 xdbm;
+	u32 i, tx_counter = 0;
+
+	if (bw == RTW89_CHANNEL_WIDTH_40)
+		ch_tmp = ch - 2;
+	else if (bw == RTW89_CHANNEL_WIDTH_80)
+		ch_tmp = ch - 6;
+	else
+		ch_tmp = ch;
+
+	power = rtw89_phy_read_txpwr_limit(rtwdev, RTW89_CHANNEL_WIDTH_20, RTW89_1TX,
+					   RTW89_RS_OFDM, RTW89_NONBF, ch_tmp);
+
+	xdbm = (power * 100) >> mac_reg->txpwr_factor_mac;
+
+	if (xdbm > 1800)
+		xdbm = 68;
+	else
+		xdbm = power * 2;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+		    "[TSSI] %s: phy=%d org_power=%d xdbm=%d\n",
+		    __func__, phy, power, xdbm);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DPK, BTC_WRFK_START);
+	rtw89_mac_stop_sch_tx(rtwdev, phy, &tx_en, RTW89_SCH_TX_SEL_ALL);
+	_wait_rx_mode(rtwdev, _kpath(rtwdev, phy));
+	tx_counter = rtw89_phy_read32_mask(rtwdev, R_TX_COUNTER, MASKLWORD);
+
+	_tssi_hw_tx(rtwdev, phy, RF_PATH_AB, xdbm, true);
+	mdelay(15);
+	_tssi_hw_tx(rtwdev, phy, RF_PATH_AB, xdbm, false);
+
+	tx_counter = rtw89_phy_read32_mask(rtwdev, R_TX_COUNTER, MASKLWORD) -
+		    tx_counter;
+
+	if (rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB, MASKHWORD) != 0xc000 &&
+	    rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB, MASKHWORD) != 0x0) {
+		for (i = 0; i < 6; i++) {
+			tssi_info->default_txagc_offset[RF_PATH_A] =
+				rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB,
+						      MASKBYTE3);
+
+			if (tssi_info->default_txagc_offset[RF_PATH_A] != 0x0)
+				break;
+		}
+	}
+
+	if (rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB_S1, MASKHWORD) != 0xc000 &&
+	    rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB_S1, MASKHWORD) != 0x0) {
+		for (i = 0; i < 6; i++) {
+			tssi_info->default_txagc_offset[RF_PATH_B] =
+				rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB_S1,
+						      MASKBYTE3);
+
+			if (tssi_info->default_txagc_offset[RF_PATH_B] != 0x0)
+				break;
+		}
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+		    "[TSSI] %s: tx counter=%d\n",
+		    __func__, tx_counter);
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI,
+		    "[TSSI] Backup R_TXAGC_BB=0x%x R_TXAGC_BB_S1=0x%x\n",
+		    tssi_info->default_txagc_offset[RF_PATH_A],
+		    tssi_info->default_txagc_offset[RF_PATH_B]);
+
+	rtw8852a_bb_tx_mode_switch(rtwdev, phy, 0);
+
+	rtw89_mac_resume_sch_tx(rtwdev, phy, tx_en);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DPK, BTC_WRFK_STOP);
+}
+
+void rtw8852a_rck(struct rtw89_dev *rtwdev)
+{
+	u8 path;
+
+	for (path = 0; path < 2; path++)
+		_rck(rtwdev, path);
+}
+
+void rtw8852a_dack(struct rtw89_dev *rtwdev)
+{
+	u8 phy_map = rtw89_btc_phymap(rtwdev, RTW89_PHY_0, 0);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DACK, BTC_WRFK_START);
+	_dac_cal(rtwdev, false);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DACK, BTC_WRFK_STOP);
+}
+
+void rtw8852a_iqk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx)
+{
+	u16 tx_en;
+	u8 phy_map = rtw89_btc_phymap(rtwdev, phy_idx, 0);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_IQK, BTC_WRFK_START);
+	rtw89_mac_stop_sch_tx(rtwdev, phy_idx, &tx_en, RTW89_SCH_TX_SEL_ALL);
+	_wait_rx_mode(rtwdev, _kpath(rtwdev, phy_idx));
+
+	_iqk_init(rtwdev);
+	if (rtwdev->dbcc_en)
+		_iqk_dbcc(rtwdev, phy_idx);
+	else
+		_iqk(rtwdev, phy_idx, false);
+
+	rtw89_mac_resume_sch_tx(rtwdev, phy_idx, tx_en);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_IQK, BTC_WRFK_STOP);
+}
+
+void rtw8852a_iqk_track(struct rtw89_dev *rtwdev)
+{
+	_iqk_track(rtwdev);
+}
+
+void rtw8852a_rx_dck(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx,
+		     bool is_afe)
+{
+	u16 tx_en;
+	u8 phy_map = rtw89_btc_phymap(rtwdev, phy_idx, 0);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_RXDCK, BTC_WRFK_START);
+	rtw89_mac_stop_sch_tx(rtwdev, phy_idx, &tx_en, RTW89_SCH_TX_SEL_ALL);
+	_wait_rx_mode(rtwdev, _kpath(rtwdev, phy_idx));
+
+	_rx_dck(rtwdev, phy_idx, is_afe);
+
+	rtw89_mac_resume_sch_tx(rtwdev, phy_idx, tx_en);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_RXDCK, BTC_WRFK_STOP);
+}
+
+void rtw8852a_dpk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx)
+{
+	u16 tx_en;
+	u8 phy_map = rtw89_btc_phymap(rtwdev, phy_idx, 0);
+
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DPK, BTC_WRFK_START);
+	rtw89_mac_stop_sch_tx(rtwdev, phy_idx, &tx_en, RTW89_SCH_TX_SEL_ALL);
+	_wait_rx_mode(rtwdev, _kpath(rtwdev, phy_idx));
+
+	rtwdev->dpk.is_dpk_enable = true;
+	rtwdev->dpk.is_dpk_reload_en = false;
+	_dpk(rtwdev, phy_idx, false);
+
+	rtw89_mac_resume_sch_tx(rtwdev, phy_idx, tx_en);
+	rtw89_btc_ntfy_wl_rfk(rtwdev, phy_map, BTC_WRFKT_DPK, BTC_WRFK_STOP);
+}
+
+void rtw8852a_dpk_track(struct rtw89_dev *rtwdev)
+{
+	_dpk_track(rtwdev);
+}
+
+void rtw8852a_tssi(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	u8 i;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "[TSSI] %s: phy=%d\n",
+		    __func__, phy);
+
+	_tssi_disable(rtwdev, phy);
+
+	for (i = RF_PATH_A; i < RF_PATH_NUM_8852A; i++) {
+		_tssi_rf_setting(rtwdev, phy, i);
+		_tssi_set_sys(rtwdev, phy);
+		_tssi_ini_txpwr_ctrl_bb(rtwdev, phy, i);
+		_tssi_ini_txpwr_ctrl_bb_he_tb(rtwdev, phy, i);
+		_tssi_set_dck(rtwdev, phy, i);
+		_tssi_set_tmeter_tbl(rtwdev, phy, i);
+		_tssi_set_dac_gain_tbl(rtwdev, phy, i);
+		_tssi_slope_cal_org(rtwdev, phy, i);
+		_tssi_set_rf_gap_tbl(rtwdev, phy, i);
+		_tssi_set_slope(rtwdev, phy, i);
+		_tssi_pak(rtwdev, phy, i);
+	}
+
+	_tssi_enable(rtwdev, phy);
+	_tssi_set_efuse_to_de(rtwdev, phy);
+	_tssi_high_power(rtwdev, phy);
+	_tssi_pre_tx(rtwdev, phy);
+}
+
+void rtw8852a_tssi_scan(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	u8 i;
+
+	rtw89_debug(rtwdev, RTW89_DBG_TSSI, "[TSSI] %s: phy=%d\n",
+		    __func__, phy);
+
+	if (!rtwdev->is_tssi_mode[RF_PATH_A])
+		return;
+	if (!rtwdev->is_tssi_mode[RF_PATH_B])
+		return;
+
+	_tssi_disable(rtwdev, phy);
+
+	for (i = RF_PATH_A; i < RF_PATH_NUM_8852A; i++) {
+		_tssi_rf_setting(rtwdev, phy, i);
+		_tssi_set_sys(rtwdev, phy);
+		_tssi_set_tmeter_tbl(rtwdev, phy, i);
+		_tssi_pak(rtwdev, phy, i);
+	}
+
+	_tssi_enable(rtwdev, phy);
+	_tssi_set_efuse_to_de(rtwdev, phy);
+}
+
+void rtw8852a_tssi_track(struct rtw89_dev *rtwdev)
+{
+	_tssi_track(rtwdev);
+}
+
+static
+void _rtw8852a_tssi_avg_scan(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	if (!rtwdev->is_tssi_mode[RF_PATH_A] && !rtwdev->is_tssi_mode[RF_PATH_B])
+		return;
+
+	/* disable */
+	rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_disable_defs_tbl);
+
+	rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_AVG, B_P0_TSSI_AVG, 0x0);
+	rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_MV_AVG, B_P0_TSSI_MV_AVG, 0x0);
+
+	rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_AVG, B_P1_TSSI_AVG, 0x0);
+	rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_MV_AVG, B_P1_TSSI_MV_AVG, 0x0);
+
+	/* enable */
+	rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_enable_defs_ab_tbl);
+}
+
+static
+void _rtw8852a_tssi_set_avg(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy)
+{
+	if (!rtwdev->is_tssi_mode[RF_PATH_A] && !rtwdev->is_tssi_mode[RF_PATH_B])
+		return;
+
+	/* disable */
+	rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_disable_defs_tbl);
+
+	rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_AVG, B_P0_TSSI_AVG, 0x4);
+	rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_MV_AVG, B_P0_TSSI_MV_AVG, 0x2);
+
+	rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_AVG, B_P1_TSSI_AVG, 0x4);
+	rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_MV_AVG, B_P1_TSSI_MV_AVG, 0x2);
+
+	/* enable */
+	rtw89_rfk_parser(rtwdev, &rtw8852a_tssi_enable_defs_ab_tbl);
+}
+
+static void rtw8852a_tssi_set_avg(struct rtw89_dev *rtwdev,
+				  enum rtw89_phy_idx phy, bool enable)
+{
+	if (!rtwdev->is_tssi_mode[RF_PATH_A] && !rtwdev->is_tssi_mode[RF_PATH_B])
+		return;
+
+	if (enable) {
+		/* SCAN_START */
+		_rtw8852a_tssi_avg_scan(rtwdev, phy);
+	} else {
+		/* SCAN_END */
+		_rtw8852a_tssi_set_avg(rtwdev, phy);
+	}
+}
+
+static void rtw8852a_tssi_default_txagc(struct rtw89_dev *rtwdev,
+					enum rtw89_phy_idx phy, bool enable)
+{
+	struct rtw89_tssi_info *tssi_info = &rtwdev->tssi;
+	u8 i;
+
+	if (!rtwdev->is_tssi_mode[RF_PATH_A] && !rtwdev->is_tssi_mode[RF_PATH_B])
+		return;
+
+	if (enable) {
+		if (rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB, B_TXAGC_BB_OFT) != 0xc000 &&
+		    rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB, B_TXAGC_BB_OFT) != 0x0) {
+			for (i = 0; i < 6; i++) {
+				tssi_info->default_txagc_offset[RF_PATH_A] =
+					rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB,
+							      B_TXAGC_BB);
+				if (tssi_info->default_txagc_offset[RF_PATH_A])
+					break;
+			}
+		}
+
+		if (rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB_S1, B_TXAGC_BB_S1_OFT) != 0xc000 &&
+		    rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB_S1, B_TXAGC_BB_S1_OFT) != 0x0) {
+			for (i = 0; i < 6; i++) {
+				tssi_info->default_txagc_offset[RF_PATH_B] =
+					rtw89_phy_read32_mask(rtwdev, R_TXAGC_BB_S1,
+							      B_TXAGC_BB_S1);
+				if (tssi_info->default_txagc_offset[RF_PATH_B])
+					break;
+			}
+		}
+	} else {
+		rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_OFT,
+				       tssi_info->default_txagc_offset[RF_PATH_A]);
+		rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_OFT,
+				       tssi_info->default_txagc_offset[RF_PATH_B]);
+
+		rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_OFT_EN, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_P0_TSSI_TRK, B_P0_TSSI_OFT_EN, 0x1);
+
+		rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_OFT_EN, 0x0);
+		rtw89_phy_write32_mask(rtwdev, R_P1_TSSI_TRK, B_P1_TSSI_OFT_EN, 0x1);
+	}
+}
+
+void rtw8852a_wifi_scan_notify(struct rtw89_dev *rtwdev,
+			       bool scan_start, enum rtw89_phy_idx phy_idx)
+{
+	if (scan_start) {
+		rtw8852a_tssi_default_txagc(rtwdev, phy_idx, true);
+		rtw8852a_tssi_set_avg(rtwdev, phy_idx, true);
+	} else {
+		rtw8852a_tssi_default_txagc(rtwdev, phy_idx, false);
+		rtw8852a_tssi_set_avg(rtwdev, phy_idx, false);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk.h
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_8852A_RFK_H__
+#define __RTW89_8852A_RFK_H__
+
+#include "core.h"
+
+void rtw8852a_rck(struct rtw89_dev *rtwdev);
+void rtw8852a_dack(struct rtw89_dev *rtwdev);
+void rtw8852a_iqk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx);
+void rtw8852a_iqk_track(struct rtw89_dev *rtwdev);
+void rtw8852a_rx_dck(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy_idx,
+		     bool is_afe);
+void rtw8852a_dpk(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy);
+void rtw8852a_dpk_track(struct rtw89_dev *rtwdev);
+void rtw8852a_tssi(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy);
+void rtw8852a_tssi_scan(struct rtw89_dev *rtwdev, enum rtw89_phy_idx phy);
+void rtw8852a_tssi_track(struct rtw89_dev *rtwdev);
+void rtw8852a_wifi_scan_notify(struct rtw89_dev *rtwdev, bool scan_start,
+			       enum rtw89_phy_idx phy_idx);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk_table.c
@@ -0,0 +1,1607 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "rtw8852a_rfk_table.h"
+
+static const struct rtw89_reg5_def rtw8852a_tssi_sys_defs[] = {
+	DECL_RFK_WM(0x12a8, 0x00000001, 0x00000001),
+	DECL_RFK_WM(0x12a8, 0x0000000e, 0x00000002),
+	DECL_RFK_WM(0x32a8, 0x00000001, 0x00000001),
+	DECL_RFK_WM(0x32a8, 0x0000000e, 0x00000002),
+	DECL_RFK_WM(0x12bc, 0x000000f0, 0x00000005),
+	DECL_RFK_WM(0x12bc, 0x00000f00, 0x00000005),
+	DECL_RFK_WM(0x12bc, 0x000f0000, 0x00000005),
+	DECL_RFK_WM(0x12bc, 0x0000f000, 0x00000005),
+	DECL_RFK_WM(0x120c, 0x000000ff, 0x00000033),
+	DECL_RFK_WM(0x12c0, 0x0ff00000, 0x00000033),
+	DECL_RFK_WM(0x32bc, 0x000000f0, 0x00000005),
+	DECL_RFK_WM(0x32bc, 0x00000f00, 0x00000005),
+	DECL_RFK_WM(0x32bc, 0x000f0000, 0x00000005),
+	DECL_RFK_WM(0x32bc, 0x0000f000, 0x00000005),
+	DECL_RFK_WM(0x320c, 0x000000ff, 0x00000033),
+	DECL_RFK_WM(0x32c0, 0x0ff00000, 0x00000033),
+	DECL_RFK_WM(0x0300, 0xff000000, 0x00000019),
+	DECL_RFK_WM(0x0304, 0x000000ff, 0x00000019),
+	DECL_RFK_WM(0x0304, 0x0000ff00, 0x0000001d),
+	DECL_RFK_WM(0x0314, 0xffff0000, 0x00002044),
+	DECL_RFK_WM(0x0318, 0x0000ffff, 0x00002042),
+	DECL_RFK_WM(0x0318, 0xffff0000, 0x00002002),
+	DECL_RFK_WM(0x0020, 0x00006000, 0x00000003),
+	DECL_RFK_WM(0x0024, 0x00006000, 0x00000003),
+	DECL_RFK_WM(0x0704, 0xffff0000, 0x0000601e),
+	DECL_RFK_WM(0x2704, 0xffff0000, 0x0000601e),
+	DECL_RFK_WM(0x0700, 0xf0000000, 0x00000004),
+	DECL_RFK_WM(0x2700, 0xf0000000, 0x00000004),
+	DECL_RFK_WM(0x0650, 0x3c000000, 0x00000000),
+	DECL_RFK_WM(0x2650, 0x3c000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_sys_defs);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_sys_defs_2g[] = {
+	DECL_RFK_WM(0x120c, 0x000000ff, 0x00000033),
+	DECL_RFK_WM(0x12c0, 0x0ff00000, 0x00000033),
+	DECL_RFK_WM(0x32c0, 0x0ff00000, 0x00000033),
+	DECL_RFK_WM(0x320c, 0x000000ff, 0x00000033),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_sys_defs_2g);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_sys_defs_5g[] = {
+	DECL_RFK_WM(0x120c, 0x000000ff, 0x00000044),
+	DECL_RFK_WM(0x12c0, 0x0ff00000, 0x00000044),
+	DECL_RFK_WM(0x32c0, 0x0ff00000, 0x00000044),
+	DECL_RFK_WM(0x320c, 0x000000ff, 0x00000044),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_sys_defs_5g);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txpwr_ctrl_bb_defs_a[] = {
+	DECL_RFK_WM(0x5800, 0x000000ff, 0x0000007f),
+	DECL_RFK_WM(0x5800, 0x0000ff00, 0x00000080),
+	DECL_RFK_WM(0x5800, 0x003f0000, 0x0000003f),
+	DECL_RFK_WM(0x5800, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x5800, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x5800, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x5804, 0xf8000000, 0x00000000),
+	DECL_RFK_WM(0x580c, 0x0000007f, 0x00000040),
+	DECL_RFK_WM(0x580c, 0x00007f00, 0x00000040),
+	DECL_RFK_WM(0x580c, 0x00008000, 0x00000000),
+	DECL_RFK_WM(0x580c, 0x0fff0000, 0x00000000),
+	DECL_RFK_WM(0x5810, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x5810, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x5810, 0x0000fc00, 0x00000000),
+	DECL_RFK_WM(0x5810, 0x00010000, 0x00000001),
+	DECL_RFK_WM(0x5810, 0x00fe0000, 0x00000000),
+	DECL_RFK_WM(0x5810, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x5810, 0x06000000, 0x00000000),
+	DECL_RFK_WM(0x5810, 0x38000000, 0x00000003),
+	DECL_RFK_WM(0x5810, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x5810, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x00000c00, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x00001000, 0x00000001),
+	DECL_RFK_WM(0x5814, 0x00002000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x00004000, 0x00000001),
+	DECL_RFK_WM(0x5814, 0x00038000, 0x00000005),
+	DECL_RFK_WM(0x5814, 0x003c0000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x01c00000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x18000000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0xe0000000, 0x00000000),
+	DECL_RFK_WM(0x5818, 0x000000ff, 0x00000000),
+	DECL_RFK_WM(0x5818, 0x0001ff00, 0x00000018),
+	DECL_RFK_WM(0x5818, 0x03fe0000, 0x00000016),
+	DECL_RFK_WM(0x5818, 0xfc000000, 0x00000000),
+	DECL_RFK_WM(0x581c, 0x000003ff, 0x00000280),
+	DECL_RFK_WM(0x581c, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x581c, 0x00100000, 0x00000000),
+	DECL_RFK_WM(0x581c, 0x01e00000, 0x00000008),
+	DECL_RFK_WM(0x581c, 0x01e00000, 0x0000000e),
+	DECL_RFK_WM(0x581c, 0x1e000000, 0x00000008),
+	DECL_RFK_WM(0x581c, 0x1e000000, 0x0000000e),
+	DECL_RFK_WM(0x581c, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x5820, 0x00000fff, 0x00000080),
+	DECL_RFK_WM(0x5820, 0x0000f000, 0x0000000f),
+	DECL_RFK_WM(0x5820, 0x001f0000, 0x00000000),
+	DECL_RFK_WM(0x5820, 0xffe00000, 0x00000000),
+	DECL_RFK_WM(0x5824, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5824, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5828, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x582c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x582c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5830, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5834, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5834, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5838, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x583c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x583c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5840, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5844, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5844, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5848, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x584c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x584c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5850, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5854, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5854, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5858, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x585c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x585c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5860, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5828, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5828, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5830, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5830, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5838, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5838, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5840, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5840, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5848, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5848, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5850, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5850, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5858, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5858, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5860, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5860, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x5860, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x5864, 0x000003ff, 0x000001ff),
+	DECL_RFK_WM(0x5864, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x5864, 0x03f00000, 0x00000000),
+	DECL_RFK_WM(0x5864, 0x04000000, 0x00000000),
+	DECL_RFK_WM(0x5898, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x589c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x58a0, 0x000000ff, 0x000000fd),
+	DECL_RFK_WM(0x58a0, 0x0000ff00, 0x000000e5),
+	DECL_RFK_WM(0x58a0, 0x00ff0000, 0x000000cd),
+	DECL_RFK_WM(0x58a0, 0xff000000, 0x000000b5),
+	DECL_RFK_WM(0x58a4, 0x000000ff, 0x00000016),
+	DECL_RFK_WM(0x58a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x03fe0000, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58b0, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x0000001f, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x00000020, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x000001c0, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x0000f000, 0x00000002),
+	DECL_RFK_WM(0x58b4, 0x00ff0000, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x7f000000, 0x0000000a),
+	DECL_RFK_WM(0x58b8, 0x0000007f, 0x00000028),
+	DECL_RFK_WM(0x58b8, 0x00007f00, 0x00000076),
+	DECL_RFK_WM(0x58b8, 0x007f0000, 0x00000000),
+	DECL_RFK_WM(0x58b8, 0x7f000000, 0x00000000),
+	DECL_RFK_WM(0x58bc, 0x000000ff, 0x0000007f),
+	DECL_RFK_WM(0x58bc, 0x0000ff00, 0x00000080),
+	DECL_RFK_WM(0x58bc, 0x00030000, 0x00000003),
+	DECL_RFK_WM(0x58bc, 0x000c0000, 0x00000001),
+	DECL_RFK_WM(0x58bc, 0x00300000, 0x00000002),
+	DECL_RFK_WM(0x58bc, 0x00c00000, 0x00000002),
+	DECL_RFK_WM(0x58bc, 0x07000000, 0x00000007),
+	DECL_RFK_WM(0x58c0, 0x00fe0000, 0x0000003f),
+	DECL_RFK_WM(0x58c0, 0xff000000, 0x00000000),
+	DECL_RFK_WM(0x58c4, 0x0003ffff, 0x0003ffff),
+	DECL_RFK_WM(0x58c4, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x58c4, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x58c8, 0x00ffffff, 0x00000000),
+	DECL_RFK_WM(0x58c8, 0xf0000000, 0x00000000),
+	DECL_RFK_WM(0x58cc, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x58d0, 0x00001fff, 0x00000101),
+	DECL_RFK_WM(0x58d0, 0x0001e000, 0x00000004),
+	DECL_RFK_WM(0x58d0, 0x03fe0000, 0x00000100),
+	DECL_RFK_WM(0x58d0, 0x04000000, 0x00000000),
+	DECL_RFK_WM(0x58d4, 0x000000ff, 0x00000000),
+	DECL_RFK_WM(0x58d4, 0x0003fe00, 0x000000ff),
+	DECL_RFK_WM(0x58d4, 0x07fc0000, 0x00000100),
+	DECL_RFK_WM(0x58d8, 0x000001ff, 0x0000016c),
+	DECL_RFK_WM(0x58d8, 0x0003fe00, 0x0000005c),
+	DECL_RFK_WM(0x58d8, 0x000c0000, 0x00000002),
+	DECL_RFK_WM(0x58d8, 0xfff00000, 0x00000800),
+	DECL_RFK_WM(0x58dc, 0x000000ff, 0x0000007f),
+	DECL_RFK_WM(0x58dc, 0x0000ff00, 0x00000080),
+	DECL_RFK_WM(0x58dc, 0x00010000, 0x00000000),
+	DECL_RFK_WM(0x58dc, 0x3ff00000, 0x00000000),
+	DECL_RFK_WM(0x58dc, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x58f0, 0x000001ff, 0x000001ff),
+	DECL_RFK_WM(0x58f0, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txpwr_ctrl_bb_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txpwr_ctrl_bb_defs_b[] = {
+	DECL_RFK_WM(0x7800, 0x000000ff, 0x0000007f),
+	DECL_RFK_WM(0x7800, 0x0000ff00, 0x00000080),
+	DECL_RFK_WM(0x7800, 0x003f0000, 0x0000003f),
+	DECL_RFK_WM(0x7800, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x7800, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x7800, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x7804, 0xf8000000, 0x00000000),
+	DECL_RFK_WM(0x780c, 0x0000007f, 0x00000040),
+	DECL_RFK_WM(0x780c, 0x00007f00, 0x00000040),
+	DECL_RFK_WM(0x780c, 0x00008000, 0x00000000),
+	DECL_RFK_WM(0x780c, 0x0fff0000, 0x00000000),
+	DECL_RFK_WM(0x7810, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x7810, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x7810, 0x0000fc00, 0x00000000),
+	DECL_RFK_WM(0x7810, 0x00010000, 0x00000001),
+	DECL_RFK_WM(0x7810, 0x00fe0000, 0x00000000),
+	DECL_RFK_WM(0x7810, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x7810, 0x06000000, 0x00000000),
+	DECL_RFK_WM(0x7810, 0x38000000, 0x00000003),
+	DECL_RFK_WM(0x7810, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x7810, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x00000c00, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x00001000, 0x00000001),
+	DECL_RFK_WM(0x7814, 0x00002000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x00004000, 0x00000001),
+	DECL_RFK_WM(0x7814, 0x00038000, 0x00000005),
+	DECL_RFK_WM(0x7814, 0x003c0000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x01c00000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x18000000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0xe0000000, 0x00000000),
+	DECL_RFK_WM(0x7818, 0x000000ff, 0x00000000),
+	DECL_RFK_WM(0x7818, 0x0001ff00, 0x00000018),
+	DECL_RFK_WM(0x7818, 0x03fe0000, 0x00000016),
+	DECL_RFK_WM(0x7818, 0xfc000000, 0x00000000),
+	DECL_RFK_WM(0x781c, 0x000003ff, 0x00000280),
+	DECL_RFK_WM(0x781c, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x781c, 0x00100000, 0x00000000),
+	DECL_RFK_WM(0x781c, 0x01e00000, 0x00000008),
+	DECL_RFK_WM(0x781c, 0x01e00000, 0x0000000e),
+	DECL_RFK_WM(0x781c, 0x1e000000, 0x00000008),
+	DECL_RFK_WM(0x781c, 0x1e000000, 0x0000000e),
+	DECL_RFK_WM(0x781c, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x7820, 0x00000fff, 0x00000080),
+	DECL_RFK_WM(0x7820, 0x0000f000, 0x00000000),
+	DECL_RFK_WM(0x7820, 0x001f0000, 0x00000000),
+	DECL_RFK_WM(0x7820, 0xffe00000, 0x00000000),
+	DECL_RFK_WM(0x7824, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7824, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7828, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x782c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x782c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7830, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7834, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7834, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7838, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x783c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x783c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7840, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7844, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7844, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7848, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x784c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x784c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7850, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7854, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7854, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7858, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x785c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x785c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7860, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7828, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7828, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7830, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7830, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7838, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7838, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7840, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7840, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7848, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7848, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7850, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7850, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7858, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7858, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7860, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7860, 0x7fc00000, 0x00000000),
+	DECL_RFK_WM(0x7860, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x7864, 0x000003ff, 0x000001ff),
+	DECL_RFK_WM(0x7864, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x7864, 0x03f00000, 0x00000000),
+	DECL_RFK_WM(0x7864, 0x04000000, 0x00000000),
+	DECL_RFK_WM(0x7898, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x789c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x78a0, 0x000000ff, 0x000000fd),
+	DECL_RFK_WM(0x78a0, 0x0000ff00, 0x000000e5),
+	DECL_RFK_WM(0x78a0, 0x00ff0000, 0x000000cd),
+	DECL_RFK_WM(0x78a0, 0xff000000, 0x000000b5),
+	DECL_RFK_WM(0x78a4, 0x000000ff, 0x00000016),
+	DECL_RFK_WM(0x78a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x03fe0000, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78b0, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x0000001f, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x00000020, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x000001c0, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x0000f000, 0x00000002),
+	DECL_RFK_WM(0x78b4, 0x00ff0000, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x7f000000, 0x0000000a),
+	DECL_RFK_WM(0x78b8, 0x0000007f, 0x00000028),
+	DECL_RFK_WM(0x78b8, 0x00007f00, 0x00000076),
+	DECL_RFK_WM(0x78b8, 0x007f0000, 0x00000000),
+	DECL_RFK_WM(0x78b8, 0x7f000000, 0x00000000),
+	DECL_RFK_WM(0x78bc, 0x000000ff, 0x0000007f),
+	DECL_RFK_WM(0x78bc, 0x0000ff00, 0x00000080),
+	DECL_RFK_WM(0x78bc, 0x00030000, 0x00000003),
+	DECL_RFK_WM(0x78bc, 0x000c0000, 0x00000001),
+	DECL_RFK_WM(0x78bc, 0x00300000, 0x00000002),
+	DECL_RFK_WM(0x78bc, 0x00c00000, 0x00000002),
+	DECL_RFK_WM(0x78bc, 0x07000000, 0x00000007),
+	DECL_RFK_WM(0x78c0, 0x00fe0000, 0x0000003f),
+	DECL_RFK_WM(0x78c0, 0xff000000, 0x00000000),
+	DECL_RFK_WM(0x78c4, 0x0003ffff, 0x0003ffff),
+	DECL_RFK_WM(0x78c4, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x78c4, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x78c8, 0x00ffffff, 0x00000000),
+	DECL_RFK_WM(0x78c8, 0xf0000000, 0x00000000),
+	DECL_RFK_WM(0x78cc, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x78d0, 0x00001fff, 0x00000101),
+	DECL_RFK_WM(0x78d0, 0x0001e000, 0x00000004),
+	DECL_RFK_WM(0x78d0, 0x03fe0000, 0x00000100),
+	DECL_RFK_WM(0x78d0, 0x04000000, 0x00000000),
+	DECL_RFK_WM(0x78d4, 0x000000ff, 0x00000000),
+	DECL_RFK_WM(0x78d4, 0x0003fe00, 0x000000ff),
+	DECL_RFK_WM(0x78d4, 0x07fc0000, 0x00000100),
+	DECL_RFK_WM(0x78d8, 0x000001ff, 0x0000016c),
+	DECL_RFK_WM(0x78d8, 0x0003fe00, 0x0000005c),
+	DECL_RFK_WM(0x78d8, 0x000c0000, 0x00000002),
+	DECL_RFK_WM(0x78d8, 0xfff00000, 0x00000800),
+	DECL_RFK_WM(0x78dc, 0x000000ff, 0x0000007f),
+	DECL_RFK_WM(0x78dc, 0x0000ff00, 0x00000080),
+	DECL_RFK_WM(0x78dc, 0x00010000, 0x00000000),
+	DECL_RFK_WM(0x78dc, 0x3ff00000, 0x00000000),
+	DECL_RFK_WM(0x78dc, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x78f0, 0x000001ff, 0x000001ff),
+	DECL_RFK_WM(0x78f0, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txpwr_ctrl_bb_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txpwr_ctrl_bb_defs_2g[] = {
+	DECL_RFK_WM(0x58d8, 0x000001ff, 0x0000013c),
+	DECL_RFK_WM(0x78d8, 0x000001ff, 0x0000013c),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txpwr_ctrl_bb_defs_2g);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txpwr_ctrl_bb_defs_5g[] = {
+	DECL_RFK_WM(0x58d8, 0x000001ff, 0x0000016c),
+	DECL_RFK_WM(0x78d8, 0x000001ff, 0x0000016c),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txpwr_ctrl_bb_defs_5g);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_a[] = {
+	DECL_RFK_WM(0x58a0, 0xffffffff, 0x000000fc),
+	DECL_RFK_WM(0x58e4, 0x0000007f, 0x00000020),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_b[] = {
+	DECL_RFK_WM(0x78a0, 0xffffffff, 0x000000fc),
+	DECL_RFK_WM(0x78e4, 0x0000007f, 0x00000020),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_dck_defs_a[] = {
+	DECL_RFK_WM(0x580c, 0x0fff0000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x00001000, 0x00000001),
+	DECL_RFK_WM(0x5814, 0x00002000, 0x00000001),
+	DECL_RFK_WM(0x5814, 0x00004000, 0x00000001),
+	DECL_RFK_WM(0x5814, 0x00038000, 0x00000005),
+	DECL_RFK_WM(0x5814, 0x003c0000, 0x00000003),
+	DECL_RFK_WM(0x5814, 0x18000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_dck_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_dck_defs_b[] = {
+	DECL_RFK_WM(0x780c, 0x0fff0000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x00001000, 0x00000001),
+	DECL_RFK_WM(0x7814, 0x00002000, 0x00000001),
+	DECL_RFK_WM(0x7814, 0x00004000, 0x00000001),
+	DECL_RFK_WM(0x7814, 0x00038000, 0x00000005),
+	DECL_RFK_WM(0x7814, 0x003c0000, 0x00000003),
+	DECL_RFK_WM(0x7814, 0x18000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_dck_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_dac_gain_tbl_defs_a[] = {
+	DECL_RFK_WM(0x58b0, 0x00000fff, 0x00000000),
+	DECL_RFK_WM(0x58b0, 0x00000800, 0x00000001),
+	DECL_RFK_WM(0x5a00, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a04, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a08, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a0c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a10, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a14, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a18, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a1c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a20, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a24, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a28, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a2c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a30, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a34, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a38, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a3c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a40, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a44, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a48, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a4c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a50, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a54, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a58, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a5c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a60, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a64, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a68, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a6c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a70, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a74, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a78, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a7c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a80, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a84, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a88, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a8c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a90, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a94, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a98, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5a9c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5aa0, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5aa4, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5aa8, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5aac, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5ab0, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5ab4, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5ab8, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5abc, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x5ac0, 0xffffffff, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_dac_gain_tbl_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_dac_gain_tbl_defs_b[] = {
+	DECL_RFK_WM(0x78b0, 0x00000fff, 0x00000000),
+	DECL_RFK_WM(0x78b0, 0x00000800, 0x00000001),
+	DECL_RFK_WM(0x7a00, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a04, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a08, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a0c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a10, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a14, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a18, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a1c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a20, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a24, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a28, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a2c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a30, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a34, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a38, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a3c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a40, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a44, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a48, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a4c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a50, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a54, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a58, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a5c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a60, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a64, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a68, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a6c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a70, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a74, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a78, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a7c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a80, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a84, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a88, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a8c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a90, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a94, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a98, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7a9c, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7aa0, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7aa4, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7aa8, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7aac, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7ab0, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7ab4, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7ab8, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7abc, 0xffffffff, 0x00000000),
+	DECL_RFK_WM(0x7ac0, 0xffffffff, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_dac_gain_tbl_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_slope_cal_org_defs_a[] = {
+	DECL_RFK_WM(0x581c, 0x00100000, 0x00000000),
+	DECL_RFK_WM(0x58cc, 0x00001000, 0x00000001),
+	DECL_RFK_WM(0x58cc, 0x00000007, 0x00000000),
+	DECL_RFK_WM(0x58cc, 0x00000038, 0x00000001),
+	DECL_RFK_WM(0x58cc, 0x000001c0, 0x00000002),
+	DECL_RFK_WM(0x58cc, 0x00000e00, 0x00000003),
+	DECL_RFK_WM(0x5828, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x5898, 0x000000ff, 0x00000040),
+	DECL_RFK_WM(0x5830, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x5898, 0x0000ff00, 0x00000040),
+	DECL_RFK_WM(0x5838, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x5898, 0x00ff0000, 0x00000040),
+	DECL_RFK_WM(0x5840, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x5898, 0xff000000, 0x00000040),
+	DECL_RFK_WM(0x5848, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x589c, 0x000000ff, 0x00000040),
+	DECL_RFK_WM(0x5850, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x589c, 0x0000ff00, 0x00000040),
+	DECL_RFK_WM(0x5858, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x589c, 0x00ff0000, 0x00000040),
+	DECL_RFK_WM(0x5860, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x589c, 0xff000000, 0x00000040),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_slope_cal_org_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_slope_cal_org_defs_b[] = {
+	DECL_RFK_WM(0x781c, 0x00100000, 0x00000000),
+	DECL_RFK_WM(0x78cc, 0x00001000, 0x00000001),
+	DECL_RFK_WM(0x78cc, 0x00000007, 0x00000000),
+	DECL_RFK_WM(0x78cc, 0x00000038, 0x00000001),
+	DECL_RFK_WM(0x78cc, 0x000001c0, 0x00000002),
+	DECL_RFK_WM(0x78cc, 0x00000e00, 0x00000003),
+	DECL_RFK_WM(0x7828, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x7898, 0x000000ff, 0x00000040),
+	DECL_RFK_WM(0x7830, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x7898, 0x0000ff00, 0x00000040),
+	DECL_RFK_WM(0x7838, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x7898, 0x00ff0000, 0x00000040),
+	DECL_RFK_WM(0x7840, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x7898, 0xff000000, 0x00000040),
+	DECL_RFK_WM(0x7848, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x789c, 0x000000ff, 0x00000040),
+	DECL_RFK_WM(0x7850, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x789c, 0x0000ff00, 0x00000040),
+	DECL_RFK_WM(0x7878, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x789c, 0x00ff0000, 0x00000040),
+	DECL_RFK_WM(0x7860, 0x7fc00000, 0x00000040),
+	DECL_RFK_WM(0x789c, 0xff000000, 0x00000040),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_slope_cal_org_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_rf_gap_tbl_defs_a[] = {
+	DECL_RFK_WM(0x5814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x03fe0000, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x07fc0000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_rf_gap_tbl_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_rf_gap_tbl_defs_b[] = {
+	DECL_RFK_WM(0x7814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x03fe0000, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x07fc0000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_rf_gap_tbl_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_slope_defs_a[] = {
+	DECL_RFK_WM(0x5820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x5818, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x00000800, 0x00000001),
+	DECL_RFK_WM(0x581c, 0x20000000, 0x00000001),
+	DECL_RFK_WM(0x5820, 0x0000f000, 0x00000001),
+	DECL_RFK_WM(0x581c, 0x000003ff, 0x00000280),
+	DECL_RFK_WM(0x581c, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x58b8, 0x007f0000, 0x00000000),
+	DECL_RFK_WM(0x58b8, 0x7f000000, 0x00000000),
+	DECL_RFK_WM(0x58b4, 0x7f000000, 0x0000000a),
+	DECL_RFK_WM(0x58b8, 0x0000007f, 0x00000028),
+	DECL_RFK_WM(0x58b8, 0x00007f00, 0x00000076),
+	DECL_RFK_WM(0x5810, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x20000000, 0x00000001),
+	DECL_RFK_WM(0x580c, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x580c, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x5838, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5858, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5834, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5834, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5838, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5854, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5854, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5858, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5824, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5824, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5828, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x582c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x582c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5830, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x583c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x583c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5840, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5844, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x5844, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5848, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x584c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x584c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5850, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x585c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x585c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x5860, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x5828, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5830, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5840, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5848, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5850, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x5860, 0x003ff000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_slope_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_slope_defs_b[] = {
+	DECL_RFK_WM(0x7820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x7818, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x00000800, 0x00000001),
+	DECL_RFK_WM(0x781c, 0x20000000, 0x00000001),
+	DECL_RFK_WM(0x7820, 0x0000f000, 0x00000001),
+	DECL_RFK_WM(0x781c, 0x000003ff, 0x00000280),
+	DECL_RFK_WM(0x781c, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x78b8, 0x007f0000, 0x00000000),
+	DECL_RFK_WM(0x78b8, 0x7f000000, 0x00000000),
+	DECL_RFK_WM(0x78b4, 0x7f000000, 0x0000000a),
+	DECL_RFK_WM(0x78b8, 0x0000007f, 0x00000028),
+	DECL_RFK_WM(0x78b8, 0x00007f00, 0x00000076),
+	DECL_RFK_WM(0x7810, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x20000000, 0x00000001),
+	DECL_RFK_WM(0x780c, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x780c, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x7838, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7858, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7834, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7834, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7838, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7854, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7854, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7858, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7824, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7824, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7828, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x782c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x782c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7830, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x783c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x783c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7840, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7844, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x7844, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7848, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x784c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x784c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7850, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x785c, 0x0003ffff, 0x000115f2),
+	DECL_RFK_WM(0x785c, 0x3ffc0000, 0x00000000),
+	DECL_RFK_WM(0x7860, 0x00000fff, 0x00000121),
+	DECL_RFK_WM(0x7828, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7830, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7840, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7848, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7850, 0x003ff000, 0x00000000),
+	DECL_RFK_WM(0x7860, 0x003ff000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_slope_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_track_defs_a[] = {
+	DECL_RFK_WM(0x5820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x5818, 0x18000000, 0x00000000),
+	DECL_RFK_WM(0x5814, 0x00000800, 0x00000000),
+	DECL_RFK_WM(0x581c, 0x20000000, 0x00000001),
+	DECL_RFK_WM(0x5864, 0x000003ff, 0x000001ff),
+	DECL_RFK_WM(0x5864, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x5820, 0x00000fff, 0x00000080),
+	DECL_RFK_WM(0x5814, 0x01000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_track_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_track_defs_b[] = {
+	DECL_RFK_WM(0x7820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x7818, 0x18000000, 0x00000000),
+	DECL_RFK_WM(0x7814, 0x00000800, 0x00000000),
+	DECL_RFK_WM(0x781c, 0x20000000, 0x00000001),
+	DECL_RFK_WM(0x7864, 0x000003ff, 0x000001ff),
+	DECL_RFK_WM(0x7864, 0x000ffc00, 0x00000200),
+	DECL_RFK_WM(0x7820, 0x00000fff, 0x00000080),
+	DECL_RFK_WM(0x7814, 0x01000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_track_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txagc_ofst_mv_avg_defs_a[] = {
+	DECL_RFK_WM(0x58e4, 0x00004000, 0x00000000),
+	DECL_RFK_WM(0x58e4, 0x00004000, 0x00000001),
+	DECL_RFK_WM(0x58e4, 0x00004000, 0x00000000),
+	DECL_RFK_WM(0x58e4, 0x00008000, 0x00000000),
+	DECL_RFK_WM(0x58e4, 0x000f0000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txagc_ofst_mv_avg_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_txagc_ofst_mv_avg_defs_b[] = {
+	DECL_RFK_WM(0x78e4, 0x00004000, 0x00000000),
+	DECL_RFK_WM(0x78e4, 0x00004000, 0x00000001),
+	DECL_RFK_WM(0x78e4, 0x00004000, 0x00000000),
+	DECL_RFK_WM(0x78e4, 0x00008000, 0x00000000),
+	DECL_RFK_WM(0x78e4, 0x000f0000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_txagc_ofst_mv_avg_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_a_2g[] = {
+	DECL_RFK_WM(0x5814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x03fe0000, 0x000001d0),
+	DECL_RFK_WM(0x58a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x0003fe00, 0x000001e8),
+	DECL_RFK_WM(0x58a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x000001ff, 0x0000000b),
+	DECL_RFK_WM(0x58ac, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x07fc0000, 0x00000088),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_a_2g);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_a_5g_1[] = {
+	DECL_RFK_WM(0x5814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x03fe0000, 0x000001d7),
+	DECL_RFK_WM(0x58a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x0003fe00, 0x000001fb),
+	DECL_RFK_WM(0x58a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x0003fe00, 0x00000005),
+	DECL_RFK_WM(0x58ac, 0x07fc0000, 0x0000007c),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_a_5g_1);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_a_5g_3[] = {
+	DECL_RFK_WM(0x5814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x03fe0000, 0x000001d8),
+	DECL_RFK_WM(0x58a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x0003fe00, 0x000001fc),
+	DECL_RFK_WM(0x58a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x0003fe00, 0x00000006),
+	DECL_RFK_WM(0x58ac, 0x07fc0000, 0x00000078),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_a_5g_3);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_a_5g_4[] = {
+	DECL_RFK_WM(0x5814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x58f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x58a4, 0x03fe0000, 0x000001e5),
+	DECL_RFK_WM(0x58a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58a8, 0x0003fe00, 0x0000000a),
+	DECL_RFK_WM(0x58a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x58ac, 0x0003fe00, 0x00000011),
+	DECL_RFK_WM(0x58ac, 0x07fc0000, 0x00000075),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_a_5g_4);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_b_2g[] = {
+	DECL_RFK_WM(0x7814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x03fe0000, 0x000001cc),
+	DECL_RFK_WM(0x78a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x0003fe00, 0x000001e2),
+	DECL_RFK_WM(0x78a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x000001ff, 0x00000005),
+	DECL_RFK_WM(0x78ac, 0x0003fe00, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x07fc0000, 0x00000089),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_b_2g);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_b_5g_1[] = {
+	DECL_RFK_WM(0x7814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x03fe0000, 0x000001d5),
+	DECL_RFK_WM(0x78a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x0003fe00, 0x000001fc),
+	DECL_RFK_WM(0x78a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x0003fe00, 0x00000005),
+	DECL_RFK_WM(0x78ac, 0x07fc0000, 0x00000079),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_b_5g_1);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_b_5g_3[] = {
+	DECL_RFK_WM(0x7814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x03fe0000, 0x000001dc),
+	DECL_RFK_WM(0x78a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x0003fe00, 0x00000002),
+	DECL_RFK_WM(0x78a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x0003fe00, 0x0000000b),
+	DECL_RFK_WM(0x78ac, 0x07fc0000, 0x00000076),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_b_5g_3);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_pak_defs_b_5g_4[] = {
+	DECL_RFK_WM(0x7814, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f4, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000003ff, 0x00000000),
+	DECL_RFK_WM(0x78f8, 0x000ffc00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x0001ff00, 0x00000000),
+	DECL_RFK_WM(0x78a4, 0x03fe0000, 0x000001f0),
+	DECL_RFK_WM(0x78a8, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78a8, 0x0003fe00, 0x00000016),
+	DECL_RFK_WM(0x78a8, 0x07fc0000, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x000001ff, 0x00000000),
+	DECL_RFK_WM(0x78ac, 0x0003fe00, 0x0000001f),
+	DECL_RFK_WM(0x78ac, 0x07fc0000, 0x00000072),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_pak_defs_b_5g_4);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_enable_defs_a[] = {
+	DECL_RFK_WRF(0x0, 0x55, 0x00080, 0x00001),
+	DECL_RFK_WM(0x5818, 0x000000ff, 0x000000c0),
+	DECL_RFK_WM(0x5818, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x5818, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x5820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x5820, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x5818, 0x18000000, 0x00000003),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_enable_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_enable_defs_b[] = {
+	DECL_RFK_WRF(0x1, 0x55, 0x00080, 0x00001),
+	DECL_RFK_WM(0x7818, 0x000000ff, 0x000000c0),
+	DECL_RFK_WM(0x7818, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x7818, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x7820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x7820, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x7818, 0x18000000, 0x00000003),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_enable_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_disable_defs[] = {
+	DECL_RFK_WM(0x5820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x5818, 0x18000000, 0x00000001),
+	DECL_RFK_WM(0x7820, 0x80000000, 0x00000000),
+	DECL_RFK_WM(0x7818, 0x18000000, 0x00000001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_disable_defs);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_enable_defs_ab[] = {
+	DECL_RFK_WM(0x5820, 0x80000000, 0x0),
+	DECL_RFK_WM(0x5820, 0x80000000, 0x1),
+	DECL_RFK_WM(0x5818, 0x18000000, 0x3),
+	DECL_RFK_WM(0x7820, 0x80000000, 0x0),
+	DECL_RFK_WM(0x7820, 0x80000000, 0x1),
+	DECL_RFK_WM(0x7818, 0x18000000, 0x3),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_enable_defs_ab);
+
+static const struct rtw89_reg5_def rtw8852a_tssi_tracking_defs[] = {
+	DECL_RFK_WM(0x5800, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x58f0, 0x00080000, 0x00000000),
+	DECL_RFK_WM(0x5804, 0xf8000000, 0x00000000),
+	DECL_RFK_WM(0x58f0, 0xfff00000, 0x00000400),
+	DECL_RFK_WM(0x7800, 0x10000000, 0x00000000),
+	DECL_RFK_WM(0x78f0, 0x00080000, 0x00000000),
+	DECL_RFK_WM(0x7804, 0xf8000000, 0x00000000),
+	DECL_RFK_WM(0x78f0, 0xfff00000, 0x00000400),
+};
+
+DECLARE_RFK_TBL(rtw8852a_tssi_tracking_defs);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_afe_init_defs[] = {
+	DECL_RFK_WC(0x12ec, 0x00008000),
+	DECL_RFK_WS(0x12ec, 0x00008000),
+	DECL_RFK_WC(0x5e00, 0x00000001),
+	DECL_RFK_WS(0x5e00, 0x00000001),
+	DECL_RFK_WC(0x32ec, 0x00008000),
+	DECL_RFK_WS(0x32ec, 0x00008000),
+	DECL_RFK_WC(0x7e00, 0x00000001),
+	DECL_RFK_WS(0x7e00, 0x00000001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_afe_init_defs);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_reload_defs_a[] = {
+	DECL_RFK_WS(0x5e00, 0x00000008),
+	DECL_RFK_WS(0x5e50, 0x00000008),
+	DECL_RFK_WS(0x5e10, 0x80000000),
+	DECL_RFK_WS(0x5e60, 0x80000000),
+	DECL_RFK_WC(0x5e00, 0x00000008),
+	DECL_RFK_WC(0x5e50, 0x00000008),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_reload_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_reload_defs_b[] = {
+	DECL_RFK_WS(0x7e00, 0x00000008),
+	DECL_RFK_WS(0x7e50, 0x00000008),
+	DECL_RFK_WS(0x7e10, 0x80000000),
+	DECL_RFK_WS(0x7e60, 0x80000000),
+	DECL_RFK_WC(0x7e00, 0x00000008),
+	DECL_RFK_WC(0x7e50, 0x00000008),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_reload_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_check_addc_defs_a[] = {
+	DECL_RFK_WC(0x20f4, 0x01000000),
+	DECL_RFK_WS(0x20f8, 0x80000000),
+	DECL_RFK_WM(0x20f0, 0x00ff0000, 0x00000001),
+	DECL_RFK_WM(0x20f0, 0x00000f00, 0x00000002),
+	DECL_RFK_WC(0x20f0, 0x0000000f),
+	DECL_RFK_WM(0x20f0, 0x000000c0, 0x00000002),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_check_addc_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_check_addc_defs_b[] = {
+	DECL_RFK_WC(0x20f4, 0x01000000),
+	DECL_RFK_WS(0x20f8, 0x80000000),
+	DECL_RFK_WM(0x20f0, 0x00ff0000, 0x00000001),
+	DECL_RFK_WM(0x20f0, 0x00000f00, 0x00000002),
+	DECL_RFK_WC(0x20f0, 0x0000000f),
+	DECL_RFK_WM(0x20f0, 0x000000c0, 0x00000003),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_check_addc_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_addck_reset_defs_a[] = {
+	DECL_RFK_WC(0x12d8, 0x00000030),
+	DECL_RFK_WC(0x32d8, 0x00000030),
+	DECL_RFK_WS(0x12b8, 0x40000000),
+	DECL_RFK_WC(0x032c, 0x40000000),
+	DECL_RFK_WC(0x032c, 0x00400000),
+	DECL_RFK_WS(0x032c, 0x00400000),
+	DECL_RFK_WS(0x030c, 0x0f000000),
+	DECL_RFK_WC(0x032c, 0x00010000),
+	DECL_RFK_WS(0x12dc, 0x00000002),
+	DECL_RFK_WM(0x030c, 0x0f000000, 0x00000003),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_addck_reset_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_addck_trigger_defs_a[] = {
+	DECL_RFK_WS(0x12d8, 0x000000c0),
+	DECL_RFK_WS(0x12d8, 0x00000800),
+	DECL_RFK_WC(0x12d8, 0x00000800),
+	DECL_RFK_DELAY(1),
+	DECL_RFK_WM(0x12d8, 0x00000300, 0x00000001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_addck_trigger_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_addck_restore_defs_a[] = {
+	DECL_RFK_WC(0x12dc, 0x00000002),
+	DECL_RFK_WS(0x032c, 0x00010000),
+	DECL_RFK_WM(0x030c, 0x0f000000, 0x0000000c),
+	DECL_RFK_WS(0x032c, 0x40000000),
+	DECL_RFK_WC(0x12b8, 0x40000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_addck_restore_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_addck_reset_defs_b[] = {
+	DECL_RFK_WS(0x32b8, 0x40000000),
+	DECL_RFK_WC(0x032c, 0x40000000),
+	DECL_RFK_WC(0x032c, 0x00400000),
+	DECL_RFK_WS(0x032c, 0x00400000),
+	DECL_RFK_WS(0x030c, 0x0f000000),
+	DECL_RFK_WC(0x032c, 0x00010000),
+	DECL_RFK_WS(0x32dc, 0x00000002),
+	DECL_RFK_WM(0x030c, 0x0f000000, 0x00000003),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_addck_reset_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_addck_trigger_defs_b[] = {
+	DECL_RFK_WS(0x32d8, 0x000000c0),
+	DECL_RFK_WS(0x32d8, 0x00000800),
+	DECL_RFK_WC(0x32d8, 0x00000800),
+	DECL_RFK_DELAY(1),
+	DECL_RFK_WM(0x32d8, 0x00000300, 0x00000001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_addck_trigger_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_addck_restore_defs_b[] = {
+	DECL_RFK_WC(0x32dc, 0x00000002),
+	DECL_RFK_WS(0x032c, 0x00010000),
+	DECL_RFK_WM(0x030c, 0x0f000000, 0x0000000c),
+	DECL_RFK_WS(0x032c, 0x40000000),
+	DECL_RFK_WC(0x32b8, 0x40000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_addck_restore_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_check_dadc_defs_f_a[] = {
+	DECL_RFK_WC(0x032c, 0x40000000),
+	DECL_RFK_WS(0x030c, 0x0f000000),
+	DECL_RFK_WM(0x030c, 0x0f000000, 0x00000003),
+	DECL_RFK_WC(0x032c, 0x00010000),
+	DECL_RFK_WS(0x12dc, 0x00000001),
+	DECL_RFK_WS(0x12e8, 0x00000004),
+	DECL_RFK_WRF(0x0, 0x8f, 0x02000, 0x00001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_check_dadc_defs_f_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_check_dadc_defs_f_b[] = {
+	DECL_RFK_WC(0x032c, 0x40000000),
+	DECL_RFK_WS(0x030c, 0x0f000000),
+	DECL_RFK_WM(0x030c, 0x0f000000, 0x00000003),
+	DECL_RFK_WC(0x032c, 0x00010000),
+	DECL_RFK_WS(0x32dc, 0x00000001),
+	DECL_RFK_WS(0x32e8, 0x00000004),
+	DECL_RFK_WRF(0x1, 0x8f, 0x02000, 0x00001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_check_dadc_defs_f_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_check_dadc_defs_r_a[] = {
+	DECL_RFK_WC(0x12dc, 0x00000001),
+	DECL_RFK_WC(0x12e8, 0x00000004),
+	DECL_RFK_WRF(0x0, 0x8f, 0x02000, 0x00000),
+	DECL_RFK_WM(0x032c, 0x00010000, 0x00000001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_check_dadc_defs_r_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_check_dadc_defs_r_b[] = {
+	DECL_RFK_WC(0x32dc, 0x00000001),
+	DECL_RFK_WC(0x32e8, 0x00000004),
+	DECL_RFK_WRF(0x1, 0x8f, 0x02000, 0x00000),
+	DECL_RFK_WM(0x032c, 0x00010000, 0x00000001),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_check_dadc_defs_r_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_defs_f_a[] = {
+	DECL_RFK_WS(0x5e00, 0x00000008),
+	DECL_RFK_WC(0x5e10, 0x80000000),
+	DECL_RFK_WS(0x5e50, 0x00000008),
+	DECL_RFK_WC(0x5e60, 0x80000000),
+	DECL_RFK_WS(0x12a0, 0x00008000),
+	DECL_RFK_WM(0x12a0, 0x00007000, 0x00000003),
+	DECL_RFK_WS(0x12b8, 0x40000000),
+	DECL_RFK_WS(0x030c, 0x10000000),
+	DECL_RFK_WC(0x032c, 0x80000000),
+	DECL_RFK_WS(0x12e0, 0x00010000),
+	DECL_RFK_WS(0x12e4, 0x0c000000),
+	DECL_RFK_WM(0x5e00, 0x03ff0000, 0x00000030),
+	DECL_RFK_WM(0x5e50, 0x03ff0000, 0x00000030),
+	DECL_RFK_WC(0x5e00, 0x0c000000),
+	DECL_RFK_WC(0x5e50, 0x0c000000),
+	DECL_RFK_WC(0x5e0c, 0x00000008),
+	DECL_RFK_WC(0x5e5c, 0x00000008),
+	DECL_RFK_WS(0x5e0c, 0x00000001),
+	DECL_RFK_WS(0x5e5c, 0x00000001),
+	DECL_RFK_DELAY(1),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_defs_f_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_defs_m_a[] = {
+	DECL_RFK_WC(0x12e4, 0x0c000000),
+	DECL_RFK_WS(0x5e0c, 0x00000008),
+	DECL_RFK_WS(0x5e5c, 0x00000008),
+	DECL_RFK_DELAY(1),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_defs_m_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_defs_r_a[] = {
+	DECL_RFK_WC(0x5e0c, 0x00000001),
+	DECL_RFK_WC(0x5e5c, 0x00000001),
+	DECL_RFK_WC(0x12e0, 0x00010000),
+	DECL_RFK_WC(0x12a0, 0x00008000),
+	DECL_RFK_WS(0x12a0, 0x00007000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_defs_r_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_defs_f_b[] = {
+	DECL_RFK_WS(0x7e00, 0x00000008),
+	DECL_RFK_WC(0x7e10, 0x80000000),
+	DECL_RFK_WS(0x7e50, 0x00000008),
+	DECL_RFK_WC(0x7e60, 0x80000000),
+	DECL_RFK_WS(0x32a0, 0x00008000),
+	DECL_RFK_WM(0x32a0, 0x00007000, 0x00000003),
+	DECL_RFK_WS(0x32b8, 0x40000000),
+	DECL_RFK_WS(0x030c, 0x10000000),
+	DECL_RFK_WC(0x032c, 0x80000000),
+	DECL_RFK_WS(0x32e0, 0x00010000),
+	DECL_RFK_WS(0x32e4, 0x0c000000),
+	DECL_RFK_WM(0x7e00, 0x03ff0000, 0x00000030),
+	DECL_RFK_WM(0x7e50, 0x03ff0000, 0x00000030),
+	DECL_RFK_WC(0x7e00, 0x0c000000),
+	DECL_RFK_WC(0x7e50, 0x0c000000),
+	DECL_RFK_WC(0x7e0c, 0x00000008),
+	DECL_RFK_WC(0x7e5c, 0x00000008),
+	DECL_RFK_WS(0x7e0c, 0x00000001),
+	DECL_RFK_WS(0x7e5c, 0x00000001),
+	DECL_RFK_DELAY(1),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_defs_f_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_defs_m_b[] = {
+	DECL_RFK_WC(0x32e4, 0x0c000000),
+	DECL_RFK_WM(0x7e0c, 0x00000008, 0x00000001),
+	DECL_RFK_WM(0x7e5c, 0x00000008, 0x00000001),
+	DECL_RFK_DELAY(1),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_defs_m_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dack_defs_r_b[] = {
+	DECL_RFK_WC(0x7e0c, 0x00000001),
+	DECL_RFK_WC(0x7e5c, 0x00000001),
+	DECL_RFK_WC(0x32e0, 0x00010000),
+	DECL_RFK_WC(0x32a0, 0x00008000),
+	DECL_RFK_WS(0x32a0, 0x00007000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dack_defs_r_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_sf_defs_a[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000101),
+	DECL_RFK_WS(0x12b8, 0x40000000),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000041),
+	DECL_RFK_WS(0x12b8, 0x10000000),
+	DECL_RFK_WS(0x58c8, 0x01000000),
+	DECL_RFK_WS(0x5864, 0xc0000000),
+	DECL_RFK_WS(0x2008, 0x01ffffff),
+	DECL_RFK_WS(0x0c1c, 0x00000004),
+	DECL_RFK_WS(0x0700, 0x08000000),
+	DECL_RFK_WS(0x0c70, 0x000003ff),
+	DECL_RFK_WS(0x0c60, 0x00000003),
+	DECL_RFK_WS(0x0c6c, 0x00000001),
+	DECL_RFK_WS(0x58ac, 0x08000000),
+	DECL_RFK_WS(0x0c3c, 0x00000200),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_sf_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_sr_defs_a[] = {
+	DECL_RFK_WS(0x4490, 0x80000000),
+	DECL_RFK_WS(0x12a0, 0x00007000),
+	DECL_RFK_WS(0x12a0, 0x00008000),
+	DECL_RFK_WM(0x12a0, 0x00070000, 0x00000003),
+	DECL_RFK_WS(0x12a0, 0x00080000),
+	DECL_RFK_WS(0x0700, 0x01000000),
+	DECL_RFK_WM(0x0700, 0x06000000, 0x00000002),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00001111),
+	DECL_RFK_WM(0x58f0, 0x00080000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_sr_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_sf_defs_b[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000202),
+	DECL_RFK_WS(0x32b8, 0x40000000),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000041),
+	DECL_RFK_WS(0x32b8, 0x10000000),
+	DECL_RFK_WS(0x78c8, 0x01000000),
+	DECL_RFK_WS(0x7864, 0xc0000000),
+	DECL_RFK_WS(0x2008, 0x01ffffff),
+	DECL_RFK_WS(0x2c1c, 0x00000004),
+	DECL_RFK_WS(0x2700, 0x08000000),
+	DECL_RFK_WS(0x0c70, 0x000003ff),
+	DECL_RFK_WS(0x0c60, 0x00000003),
+	DECL_RFK_WS(0x0c6c, 0x00000001),
+	DECL_RFK_WS(0x78ac, 0x08000000),
+	DECL_RFK_WS(0x2c3c, 0x00000200),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_sf_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_sr_defs_b[] = {
+	DECL_RFK_WS(0x6490, 0x80000000),
+	DECL_RFK_WS(0x32a0, 0x00007000),
+	DECL_RFK_WS(0x32a0, 0x00008000),
+	DECL_RFK_WM(0x32a0, 0x00070000, 0x00000003),
+	DECL_RFK_WS(0x32a0, 0x00080000),
+	DECL_RFK_WS(0x2700, 0x01000000),
+	DECL_RFK_WM(0x2700, 0x06000000, 0x00000002),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00002222),
+	DECL_RFK_WM(0x78f0, 0x00080000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_sr_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_s_defs_ab[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000303),
+	DECL_RFK_WS(0x12b8, 0x40000000),
+	DECL_RFK_WS(0x32b8, 0x40000000),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000041),
+	DECL_RFK_WS(0x12b8, 0x10000000),
+	DECL_RFK_WS(0x58c8, 0x01000000),
+	DECL_RFK_WS(0x78c8, 0x01000000),
+	DECL_RFK_WS(0x5864, 0xc0000000),
+	DECL_RFK_WS(0x7864, 0xc0000000),
+	DECL_RFK_WS(0x2008, 0x01ffffff),
+	DECL_RFK_WS(0x0c1c, 0x00000004),
+	DECL_RFK_WS(0x0700, 0x08000000),
+	DECL_RFK_WS(0x0c70, 0x000003ff),
+	DECL_RFK_WS(0x0c60, 0x00000003),
+	DECL_RFK_WS(0x0c6c, 0x00000001),
+	DECL_RFK_WS(0x58ac, 0x08000000),
+	DECL_RFK_WS(0x78ac, 0x08000000),
+	DECL_RFK_WS(0x0c3c, 0x00000200),
+	DECL_RFK_WS(0x2344, 0x80000000),
+	DECL_RFK_WS(0x4490, 0x80000000),
+	DECL_RFK_WS(0x12a0, 0x00007000),
+	DECL_RFK_WS(0x12a0, 0x00008000),
+	DECL_RFK_WM(0x12a0, 0x00070000, 0x00000003),
+	DECL_RFK_WS(0x12a0, 0x00080000),
+	DECL_RFK_WM(0x32a0, 0x00070000, 0x00000003),
+	DECL_RFK_WS(0x32a0, 0x00080000),
+	DECL_RFK_WS(0x0700, 0x01000000),
+	DECL_RFK_WM(0x0700, 0x06000000, 0x00000002),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00003333),
+	DECL_RFK_WM(0x58f0, 0x00080000, 0x00000000),
+	DECL_RFK_WM(0x78f0, 0x00080000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_s_defs_ab);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_r_defs_a[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000101),
+	DECL_RFK_WC(0x12b8, 0x40000000),
+	DECL_RFK_WC(0x5864, 0xc0000000),
+	DECL_RFK_WC(0x2008, 0x01ffffff),
+	DECL_RFK_WC(0x0c1c, 0x00000004),
+	DECL_RFK_WC(0x0700, 0x08000000),
+	DECL_RFK_WM(0x0c70, 0x0000001f, 0x00000003),
+	DECL_RFK_WM(0x0c70, 0x000003e0, 0x00000003),
+	DECL_RFK_WC(0x12a0, 0x000ff000),
+	DECL_RFK_WC(0x0700, 0x07000000),
+	DECL_RFK_WC(0x5864, 0x20000000),
+	DECL_RFK_WC(0x0c3c, 0x00000200),
+	DECL_RFK_WC(0x20fc, 0xffff0000),
+	DECL_RFK_WC(0x58c8, 0x01000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_r_defs_a);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_r_defs_b[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000202),
+	DECL_RFK_WC(0x32b8, 0x40000000),
+	DECL_RFK_WC(0x7864, 0xc0000000),
+	DECL_RFK_WC(0x2008, 0x01ffffff),
+	DECL_RFK_WC(0x2c1c, 0x00000004),
+	DECL_RFK_WC(0x2700, 0x08000000),
+	DECL_RFK_WM(0x0c70, 0x0000001f, 0x00000003),
+	DECL_RFK_WM(0x0c70, 0x000003e0, 0x00000003),
+	DECL_RFK_WC(0x32a0, 0x000ff000),
+	DECL_RFK_WC(0x2700, 0x07000000),
+	DECL_RFK_WC(0x7864, 0x20000000),
+	DECL_RFK_WC(0x2c3c, 0x00000200),
+	DECL_RFK_WC(0x20fc, 0xffff0000),
+	DECL_RFK_WC(0x78c8, 0x01000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_r_defs_b);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_bb_afe_r_defs_ab[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000303),
+	DECL_RFK_WC(0x12b8, 0x40000000),
+	DECL_RFK_WC(0x32b8, 0x40000000),
+	DECL_RFK_WC(0x5864, 0xc0000000),
+	DECL_RFK_WC(0x7864, 0xc0000000),
+	DECL_RFK_WC(0x2008, 0x01ffffff),
+	DECL_RFK_WC(0x0c1c, 0x00000004),
+	DECL_RFK_WC(0x0700, 0x08000000),
+	DECL_RFK_WM(0x0c70, 0x0000001f, 0x00000003),
+	DECL_RFK_WM(0x0c70, 0x000003e0, 0x00000003),
+	DECL_RFK_WC(0x12a0, 0x000ff000),
+	DECL_RFK_WC(0x32a0, 0x000ff000),
+	DECL_RFK_WC(0x0700, 0x07000000),
+	DECL_RFK_WC(0x5864, 0x20000000),
+	DECL_RFK_WC(0x7864, 0x20000000),
+	DECL_RFK_WC(0x0c3c, 0x00000200),
+	DECL_RFK_WC(0x20fc, 0xffff0000),
+	DECL_RFK_WC(0x58c8, 0x01000000),
+	DECL_RFK_WC(0x78c8, 0x01000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_bb_afe_r_defs_ab);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_lbk_rxiqk_defs_f[] = {
+	DECL_RFK_WM(0x030c, 0xff000000, 0x0000000f),
+	DECL_RFK_DELAY(1),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000003),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x0000a001),
+	DECL_RFK_DELAY(1),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x0000a041),
+	DECL_RFK_WS(0x8074, 0x80000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_lbk_rxiqk_defs_f);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_lbk_rxiqk_defs_r[] = {
+	DECL_RFK_WC(0x8074, 0x80000000),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x0000001f),
+	DECL_RFK_DELAY(1),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000001),
+	DECL_RFK_DELAY(1),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000041),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000303),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00003333),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_lbk_rxiqk_defs_r);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_dpk_pas_read_defs[] = {
+	DECL_RFK_WM(0x80d4, 0x00ff0000, 0x00000006),
+	DECL_RFK_WC(0x80bc, 0x00004000),
+	DECL_RFK_WM(0x80c0, 0x00ff0000, 0x00000008),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_dpk_pas_read_defs);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_iqk_set_defs_nondbcc_path01[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000303),
+	DECL_RFK_WM(0x5864, 0x18000000, 0x00000003),
+	DECL_RFK_WM(0x7864, 0x18000000, 0x00000003),
+	DECL_RFK_WM(0x12b8, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x32b8, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000001),
+	DECL_RFK_WM(0x12b8, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x58c8, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x78c8, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x5864, 0xc0000000, 0x00000003),
+	DECL_RFK_WM(0x7864, 0xc0000000, 0x00000003),
+	DECL_RFK_WM(0x2008, 0x01ffffff, 0x01ffffff),
+	DECL_RFK_WM(0x0c1c, 0x00000004, 0x00000001),
+	DECL_RFK_WM(0x0700, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x0c70, 0x000003ff, 0x000003ff),
+	DECL_RFK_WM(0x0c60, 0x00000003, 0x00000003),
+	DECL_RFK_WM(0x0c6c, 0x00000001, 0x00000001),
+	DECL_RFK_WM(0x58ac, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x78ac, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x0c3c, 0x00000200, 0x00000001),
+	DECL_RFK_WM(0x2344, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x4490, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x12a0, 0x00007000, 0x00000007),
+	DECL_RFK_WM(0x12a0, 0x00008000, 0x00000001),
+	DECL_RFK_WM(0x12a0, 0x00070000, 0x00000003),
+	DECL_RFK_WM(0x12a0, 0x00080000, 0x00000001),
+	DECL_RFK_WM(0x32a0, 0x00070000, 0x00000003),
+	DECL_RFK_WM(0x32a0, 0x00080000, 0x00000001),
+	DECL_RFK_WM(0x0700, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x0700, 0x06000000, 0x00000002),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00003333),
+	DECL_RFK_WM(0x58f0, 0x00080000, 0x00000000),
+	DECL_RFK_WM(0x78f0, 0x00080000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_iqk_set_defs_nondbcc_path01);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_iqk_set_defs_dbcc_path0[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000101),
+	DECL_RFK_WM(0x5864, 0x18000000, 0x00000003),
+	DECL_RFK_WM(0x7864, 0x18000000, 0x00000003),
+	DECL_RFK_WM(0x12b8, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000001),
+	DECL_RFK_WM(0x12b8, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x58c8, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x5864, 0xc0000000, 0x00000003),
+	DECL_RFK_WM(0x2008, 0x01ffffff, 0x01ffffff),
+	DECL_RFK_WM(0x0c1c, 0x00000004, 0x00000001),
+	DECL_RFK_WM(0x0700, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x0c70, 0x000003ff, 0x000003ff),
+	DECL_RFK_WM(0x0c60, 0x00000003, 0x00000003),
+	DECL_RFK_WM(0x0c6c, 0x00000001, 0x00000001),
+	DECL_RFK_WM(0x58ac, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x0c3c, 0x00000200, 0x00000001),
+	DECL_RFK_WM(0x2320, 0x00000001, 0x00000001),
+	DECL_RFK_WM(0x4490, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x12a0, 0x00007000, 0x00000007),
+	DECL_RFK_WM(0x12a0, 0x00008000, 0x00000001),
+	DECL_RFK_WM(0x12a0, 0x00070000, 0x00000003),
+	DECL_RFK_WM(0x12a0, 0x00080000, 0x00000001),
+	DECL_RFK_WM(0x0700, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x0700, 0x06000000, 0x00000002),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00001111),
+	DECL_RFK_WM(0x58f0, 0x00080000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_iqk_set_defs_dbcc_path0);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_iqk_set_defs_dbcc_path1[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000202),
+	DECL_RFK_WM(0x7864, 0x18000000, 0x00000003),
+	DECL_RFK_WM(0x32b8, 0x40000000, 0x00000001),
+	DECL_RFK_WM(0x030c, 0xff000000, 0x00000013),
+	DECL_RFK_WM(0x032c, 0xffff0000, 0x00000001),
+	DECL_RFK_WM(0x32b8, 0x10000000, 0x00000001),
+	DECL_RFK_WM(0x78c8, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x7864, 0xc0000000, 0x00000003),
+	DECL_RFK_WM(0x2008, 0x01ffffff, 0x01ffffff),
+	DECL_RFK_WM(0x2c1c, 0x00000004, 0x00000001),
+	DECL_RFK_WM(0x2700, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x0c70, 0x000003ff, 0x000003ff),
+	DECL_RFK_WM(0x0c60, 0x00000003, 0x00000003),
+	DECL_RFK_WM(0x0c6c, 0x00000001, 0x00000001),
+	DECL_RFK_WM(0x78ac, 0x08000000, 0x00000001),
+	DECL_RFK_WM(0x2c3c, 0x00000200, 0x00000001),
+	DECL_RFK_WM(0x6490, 0x80000000, 0x00000001),
+	DECL_RFK_WM(0x32a0, 0x00007000, 0x00000007),
+	DECL_RFK_WM(0x32a0, 0x00008000, 0x00000001),
+	DECL_RFK_WM(0x32a0, 0x00070000, 0x00000003),
+	DECL_RFK_WM(0x32a0, 0x00080000, 0x00000001),
+	DECL_RFK_WM(0x2700, 0x01000000, 0x00000001),
+	DECL_RFK_WM(0x2700, 0x06000000, 0x00000002),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00002222),
+	DECL_RFK_WM(0x78f0, 0x00080000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_iqk_set_defs_dbcc_path1);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_iqk_restore_defs_nondbcc_path01[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000303),
+	DECL_RFK_WM(0x12b8, 0x40000000, 0x00000000),
+	DECL_RFK_WM(0x32b8, 0x40000000, 0x00000000),
+	DECL_RFK_WM(0x5864, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x7864, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x2008, 0x01ffffff, 0x00000000),
+	DECL_RFK_WM(0x0c1c, 0x00000004, 0x00000000),
+	DECL_RFK_WM(0x0700, 0x08000000, 0x00000000),
+	DECL_RFK_WM(0x0c70, 0x0000001f, 0x00000003),
+	DECL_RFK_WM(0x0c70, 0x000003e0, 0x00000003),
+	DECL_RFK_WM(0x12a0, 0x000ff000, 0x00000000),
+	DECL_RFK_WM(0x32a0, 0x000ff000, 0x00000000),
+	DECL_RFK_WM(0x0700, 0x07000000, 0x00000000),
+	DECL_RFK_WM(0x5864, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x7864, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x0c3c, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x2320, 0x00000001, 0x00000000),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000000),
+	DECL_RFK_WM(0x58c8, 0x01000000, 0x00000000),
+	DECL_RFK_WM(0x78c8, 0x01000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_iqk_restore_defs_nondbcc_path01);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_iqk_restore_defs_dbcc_path0[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000101),
+	DECL_RFK_WM(0x12b8, 0x40000000, 0x00000000),
+	DECL_RFK_WM(0x5864, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x2008, 0x01ffffff, 0x00000000),
+	DECL_RFK_WM(0x0c1c, 0x00000004, 0x00000000),
+	DECL_RFK_WM(0x0700, 0x08000000, 0x00000000),
+	DECL_RFK_WM(0x0c70, 0x0000001f, 0x00000003),
+	DECL_RFK_WM(0x0c70, 0x000003e0, 0x00000003),
+	DECL_RFK_WM(0x12a0, 0x000ff000, 0x00000000),
+	DECL_RFK_WM(0x0700, 0x07000000, 0x00000000),
+	DECL_RFK_WM(0x5864, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x0c3c, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000000),
+	DECL_RFK_WM(0x58c8, 0x01000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_iqk_restore_defs_dbcc_path0);
+
+static const struct rtw89_reg5_def rtw8852a_rfk_iqk_restore_defs_dbcc_path1[] = {
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000202),
+	DECL_RFK_WM(0x32b8, 0x40000000, 0x00000000),
+	DECL_RFK_WM(0x7864, 0xc0000000, 0x00000000),
+	DECL_RFK_WM(0x2008, 0x01ffffff, 0x00000000),
+	DECL_RFK_WM(0x2c1c, 0x00000004, 0x00000000),
+	DECL_RFK_WM(0x2700, 0x08000000, 0x00000000),
+	DECL_RFK_WM(0x0c70, 0x0000001f, 0x00000003),
+	DECL_RFK_WM(0x0c70, 0x000003e0, 0x00000003),
+	DECL_RFK_WM(0x32a0, 0x000ff000, 0x00000000),
+	DECL_RFK_WM(0x2700, 0x07000000, 0x00000000),
+	DECL_RFK_WM(0x7864, 0x20000000, 0x00000000),
+	DECL_RFK_WM(0x2c3c, 0x00000200, 0x00000000),
+	DECL_RFK_WM(0x20fc, 0xffff0000, 0x00000000),
+	DECL_RFK_WM(0x78c8, 0x01000000, 0x00000000),
+};
+
+DECLARE_RFK_TBL(rtw8852a_rfk_iqk_restore_defs_dbcc_path1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk_table.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a_rfk_table.h
@@ -0,0 +1,133 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_8852A_RFK_TABLE_H__
+#define __RTW89_8852A_RFK_TABLE_H__
+
+#include "core.h"
+
+enum rtw89_rfk_flag {
+	RTW89_RFK_F_WRF = 0,
+	RTW89_RFK_F_WM = 1,
+	RTW89_RFK_F_WS = 2,
+	RTW89_RFK_F_WC = 3,
+	RTW89_RFK_F_DELAY = 4,
+	RTW89_RFK_F_NUM,
+};
+
+struct rtw89_rfk_tbl {
+	const struct rtw89_reg5_def *defs;
+	u32 size;
+};
+
+#define DECLARE_RFK_TBL(_name)			\
+const struct rtw89_rfk_tbl _name ## _tbl = {	\
+	.defs = _name,				\
+	.size = ARRAY_SIZE(_name),		\
+}
+
+#define DECL_RFK_WRF(_path, _addr, _mask, _data)	\
+	{.flag = RTW89_RFK_F_WRF,			\
+	 .path = _path,					\
+	 .addr = _addr,					\
+	 .mask = _mask,					\
+	 .data = _data,}
+
+#define DECL_RFK_WM(_addr, _mask, _data)	\
+	{.flag = RTW89_RFK_F_WM,		\
+	 .addr = _addr,				\
+	 .mask = _mask,				\
+	 .data = _data,}
+
+#define DECL_RFK_WS(_addr, _mask)	\
+	{.flag = RTW89_RFK_F_WS,	\
+	 .addr = _addr,			\
+	 .mask = _mask,}
+
+#define DECL_RFK_WC(_addr, _mask)	\
+	{.flag = RTW89_RFK_F_WC,	\
+	 .addr = _addr,			\
+	 .mask = _mask,}
+
+#define DECL_RFK_DELAY(_data)		\
+	{.flag = RTW89_RFK_F_DELAY,	\
+	 .data = _data,}
+
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_sys_defs_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_sys_defs_2g_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_sys_defs_5g_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txpwr_ctrl_bb_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txpwr_ctrl_bb_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txpwr_ctrl_bb_defs_2g_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txpwr_ctrl_bb_defs_5g_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txpwr_ctrl_bb_he_tb_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_dck_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_dck_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_dac_gain_tbl_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_dac_gain_tbl_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_slope_cal_org_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_slope_cal_org_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_rf_gap_tbl_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_rf_gap_tbl_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_slope_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_slope_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_track_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_track_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txagc_ofst_mv_avg_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_txagc_ofst_mv_avg_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_a_2g_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_a_5g_1_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_a_5g_3_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_a_5g_4_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_b_2g_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_b_5g_1_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_b_5g_3_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_pak_defs_b_5g_4_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_enable_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_enable_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_enable_defs_ab_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_disable_defs_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_tssi_tracking_defs_tbl;
+
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_afe_init_defs_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_reload_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_reload_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_check_addc_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_check_addc_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_addck_reset_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_addck_trigger_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_addck_restore_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_addck_reset_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_addck_trigger_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_addck_restore_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_check_dadc_defs_f_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_check_dadc_defs_f_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_check_dadc_defs_r_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_check_dadc_defs_r_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_defs_f_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_defs_m_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_defs_r_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_defs_f_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_defs_m_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dack_defs_r_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_sf_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_sr_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_sf_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_sr_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_s_defs_ab_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_r_defs_a_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_r_defs_b_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_bb_afe_r_defs_ab_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_lbk_rxiqk_defs_f_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_lbk_rxiqk_defs_r_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_dpk_pas_read_defs_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_iqk_set_defs_nondbcc_path01_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_iqk_set_defs_dbcc_path0_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_iqk_set_defs_dbcc_path1_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_iqk_restore_defs_nondbcc_path01_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_iqk_restore_defs_dbcc_path0_tbl;
+extern const struct rtw89_rfk_tbl rtw8852a_rfk_iqk_restore_defs_dbcc_path1_tbl;
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a_table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a_table.c
@@ -0,0 +1,48725 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "phy.h"
+#include "reg.h"
+#include "rtw8852a_table.h"
+
+static const struct rtw89_reg2_def rtw89_8852a_phy_bb_regs[] = {
+	{0xF0FF0001, 0x00000000},
+	{0xF03300FF, 0x00000001},
+	{0xF03500FF, 0x00000002},
+	{0xF03200FF, 0x00000003},
+	{0xF03400FF, 0x00000004},
+	{0xF03600FF, 0x00000005},
+	{0x704, 0x601E0100},
+	{0x714, 0x00000000},
+	{0x718, 0x13332333},
+	{0x714, 0x00010000},
+	{0x720, 0x20000000},
+	{0x980, 0x10002250},
+	{0x994, 0x00000010},
+	{0x644, 0x2314283C},
+	{0x644, 0x3426283C},
+	{0x994, 0x00000010},
+	{0xC3C, 0x2840E1BF},
+	{0xC40, 0x00000000},
+	{0xC44, 0x00000007},
+	{0xC48, 0x410E4000},
+	{0xC54, 0x1001436E},
+	{0xC58, 0x41000000},
+	{0x730, 0x00000002},
+	{0xC60, 0x017FFFF2},
+	{0xC64, 0x0010A130},
+	{0xC64, 0x0010A130},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0xC68, 0x10000068},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0xC68, 0x90000068},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0xC68, 0x90000068},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0xC68, 0x10000068},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0xC68, 0x90000068},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0xC68, 0x90000068},
+	{0xA0000000, 0x00000000},
+	{0xC68, 0x10000068},
+	{0xB0000000, 0x00000000},
+	{0xC64, 0x0010A130},
+	{0xC54, 0x1EE1436E},
+	{0xC6C, 0x00000020},
+	{0x708, 0x00000000},
+	{0xC6C, 0x00000020},
+	{0x804, 0x0043F01D},
+	{0x12D0, 0x00000000},
+	{0x12EC, 0x888CA72B},
+	{0x32D0, 0x00000000},
+	{0x32EC, 0x888CA72B},
+	{0xD40, 0xF64FA0F7},
+	{0xD44, 0x0400063F},
+	{0xD48, 0x0003FF7F},
+	{0xD4C, 0x00000000},
+	{0xD50, 0xF64FA0F7},
+	{0xD54, 0x04100437},
+	{0xD58, 0x0000FF7F},
+	{0xD5C, 0x00000000},
+	{0xD60, 0x00000000},
+	{0xD64, 0x00000000},
+	{0xD70, 0x0000001D},
+	{0xD90, 0x000003FF},
+	{0xD94, 0x00000000},
+	{0xD98, 0x0000003F},
+	{0xD9C, 0x00000000},
+	{0xDA0, 0x000003FF},
+	{0xDA4, 0x00000000},
+	{0xDA8, 0x0000003F},
+	{0xDAC, 0x00000000},
+	{0xD00, 0x77777777},
+	{0xD04, 0xBBBBBBBB},
+	{0xD08, 0xBBBBBBBB},
+	{0xD0C, 0x00000070},
+	{0xD10, 0x20110900},
+	{0xD10, 0x20110FFF},
+	{0xD7C, 0x001D050C},
+	{0xD84, 0x00006207},
+	{0xD18, 0x50209900},
+	{0xD80, 0x00804100},
+	{0x714, 0x00010000},
+	{0x704, 0x601E00FD},
+	{0x710, 0xF3810000},
+	{0x000, 0x0580801F},
+	{0x000, 0x8580801F},
+	{0x334, 0xFFFFFFFF},
+	{0x33C, 0x55000000},
+	{0x340, 0x00005555},
+	{0x724, 0x00111200},
+	{0x5868, 0xA9550000},
+	{0x5870, 0x33221100},
+	{0x5874, 0x77665544},
+	{0x5878, 0xBBAA9988},
+	{0x587C, 0xFFEEDDCC},
+	{0x5880, 0x76543210},
+	{0x5884, 0xFEDCBA98},
+	{0x5888, 0x00000000},
+	{0x588C, 0x00000000},
+	{0x5894, 0x00000008},
+	{0x7868, 0xA9550000},
+	{0x7870, 0x33221100},
+	{0x7874, 0x77665544},
+	{0x7878, 0xBBAA9988},
+	{0x787C, 0xFFEEDDCC},
+	{0x7880, 0x76543210},
+	{0x7884, 0xFEDCBA98},
+	{0x7888, 0x00000000},
+	{0x788C, 0x00000000},
+	{0x7894, 0x00000008},
+	{0x240C, 0x00000000},
+	{0xC70, 0x00000400},
+	{0x700, 0x00000030},
+	{0x704, 0x601E00FF},
+	{0x704, 0x601E00FD},
+	{0x704, 0x601E00FF},
+	{0x586C, 0x000000F0},
+	{0x586C, 0x000000E0},
+	{0x586C, 0x000000D0},
+	{0x586C, 0x000000C0},
+	{0x586C, 0x000000B0},
+	{0x586C, 0x000000A0},
+	{0x586C, 0x00000090},
+	{0x586C, 0x00000080},
+	{0x586C, 0x00000070},
+	{0x586C, 0x00000060},
+	{0x586C, 0x00000050},
+	{0x586C, 0x00000040},
+	{0x586C, 0x00000030},
+	{0x586C, 0x00000020},
+	{0x586C, 0x00000010},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x586C, 0x00000000},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x586C, 0x03E00000},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x586C, 0x03E00000},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x586C, 0x00000000},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x586C, 0x03E00000},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x586C, 0x03E00000},
+	{0xA0000000, 0x00000000},
+	{0x586C, 0x00000000},
+	{0xB0000000, 0x00000000},
+	{0x786C, 0x000000F0},
+	{0x786C, 0x000000E0},
+	{0x786C, 0x000000D0},
+	{0x786C, 0x000000C0},
+	{0x786C, 0x000000B0},
+	{0x786C, 0x000000A0},
+	{0x786C, 0x00000090},
+	{0x786C, 0x00000080},
+	{0x786C, 0x00000070},
+	{0x786C, 0x00000060},
+	{0x786C, 0x00000050},
+	{0x786C, 0x00000040},
+	{0x786C, 0x00000030},
+	{0x786C, 0x00000020},
+	{0x786C, 0x00000010},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x786C, 0x00000000},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x786C, 0x03E00000},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x786C, 0x03E00000},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x786C, 0x00000000},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x786C, 0x03E00000},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x786C, 0x03E00000},
+	{0xA0000000, 0x00000000},
+	{0x786C, 0x00000000},
+	{0xB0000000, 0x00000000},
+	{0x5864, 0x080801FF},
+	{0x7864, 0x080801FF},
+	{0xC60, 0x017FFFF3},
+	{0xC6C, 0x00000021},
+	{0x58AC, 0x08000000},
+	{0x78AC, 0x08000000},
+	{0x5864, 0x180801FF},
+	{0x7864, 0x180801FF},
+	{0xC60, 0x017FFFF3},
+	{0xC60, 0x017FFFF3},
+	{0x2C60, 0x013FFF0A},
+	{0xC70, 0x00000600},
+	{0xC70, 0x00000660},
+	{0xC6C, 0x10001021},
+	{0x58AC, 0x08000000},
+	{0x78AC, 0x08000000},
+	{0x5864, 0x100801FF},
+	{0x7864, 0x100801FF},
+	{0x5864, 0x180801FF},
+	{0x7864, 0x180801FF},
+	{0x704, 0x601C01FF},
+	{0x58D4, 0x0401FE00},
+	{0x78D4, 0x0401FE00},
+	{0x58F0, 0x000401FF},
+	{0x78F0, 0x000401FF},
+	{0x58F0, 0x400401FF},
+	{0x78F0, 0x400401FF},
+	{0x12A8, 0x333378A5},
+	{0x32A8, 0x333378A5},
+	{0x2300, 0x02748790},
+	{0x2304, 0x00558670},
+	{0x2308, 0x002883F0},
+	{0x230C, 0x00090120},
+	{0x2310, 0x00000000},
+	{0x2314, 0x06000000},
+	{0x2318, 0x00000000},
+	{0x231C, 0x00000000},
+	{0x2320, 0x03020100},
+	{0x2324, 0x07060504},
+	{0x2328, 0x0B0A0908},
+	{0x232C, 0x0F0E0D0C},
+	{0x2330, 0x13121110},
+	{0x2334, 0x17161514},
+	{0x2338, 0x0C700022},
+	{0x233C, 0x0A05298F},
+	{0x2340, 0x0005298E},
+	{0x2344, 0x0006318A},
+	{0x2348, 0xB7E6318A},
+	{0x234C, 0x80039CE7},
+	{0x2350, 0x80039CE7},
+	{0x2354, 0x0005298F},
+	{0x2358, 0x0015296E},
+	{0x235C, 0x0C07FC31},
+	{0x2360, 0x0219A6AE},
+	{0x2364, 0xE4F624C3},
+	{0x2368, 0x53626F15},
+	{0x236C, 0x48000000},
+	{0x2370, 0x48000000},
+	{0x2374, 0x074C0000},
+	{0x2378, 0x202401B5},
+	{0x237C, 0x00F7000E},
+	{0x2380, 0x0F0A1111},
+	{0x2384, 0x30D9000F},
+	{0x2388, 0x0400EA02},
+	{0x238C, 0x003CB061},
+	{0x2390, 0x69C00000},
+	{0x2394, 0x00000000},
+	{0x2398, 0x000000F0},
+	{0x239C, 0x0001FFFF},
+	{0x23A0, 0x00C80064},
+	{0x23A4, 0x0190012C},
+	{0x23A8, 0x001917BE},
+	{0x23AC, 0x0B308800},
+	{0x23B0, 0x0001D5B0},
+	{0x23B4, 0x000285D2},
+	{0x23B8, 0x00000000},
+	{0x23BC, 0x00000000},
+	{0x23C0, 0x00000000},
+	{0x23C4, 0x00000000},
+	{0x23C8, 0x00000000},
+	{0x23CC, 0x00000000},
+	{0x23D0, 0x00000000},
+	{0x23D4, 0x00000000},
+	{0x23D8, 0x00000000},
+	{0x23DC, 0x00000000},
+	{0x23E0, 0x00000000},
+	{0x23E4, 0x00000000},
+	{0x23E8, 0x00000000},
+	{0x23EC, 0x00000000},
+	{0x23F0, 0x00000000},
+	{0x23F4, 0x00000000},
+	{0x23F8, 0x00000000},
+	{0x23FC, 0x00000000},
+	{0x804, 0x0043F01D},
+	{0x300, 0xF30CE31C},
+	{0x304, 0x13EF1F19},
+	{0x308, 0x0C0CF3F3},
+	{0x30C, 0x0C0C0C0C},
+	{0x310, 0x80416000},
+	{0x314, 0x0041E000},
+	{0x318, 0x20022042},
+	{0x31C, 0x20448001},
+	{0x320, 0x00410040},
+	{0x324, 0xE000E000},
+	{0x328, 0xE000E000},
+	{0x32C, 0xE000E000},
+	{0x12BC, 0x10104041},
+	{0x12C0, 0x14411111},
+	{0x32BC, 0x10104041},
+	{0x32C0, 0x14411111},
+	{0x010, 0x0005FFFF},
+	{0x604, 0x1E1E1E28},
+	{0x650, 0x00200888},
+	{0x620, 0x00141230},
+	{0x35C, 0x000004C4},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5804, 0x04237040},
+	{0x7804, 0x04237040},
+	{0x5808, 0x04237040},
+	{0x7808, 0x04237040},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5804, 0x04231040},
+	{0x7804, 0x04231040},
+	{0x5808, 0x04231040},
+	{0x7808, 0x04231040},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5804, 0x04231040},
+	{0x7804, 0x04231040},
+	{0x5808, 0x04231040},
+	{0x7808, 0x04231040},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5804, 0x04237040},
+	{0x7804, 0x04237040},
+	{0x5808, 0x04237040},
+	{0x7808, 0x04237040},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5804, 0x04231040},
+	{0x7804, 0x04231040},
+	{0x5808, 0x04231040},
+	{0x7808, 0x04231040},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5804, 0x04231040},
+	{0x7804, 0x04231040},
+	{0x5808, 0x04231040},
+	{0x7808, 0x04231040},
+	{0xA0000000, 0x00000000},
+	{0x5804, 0x04237040},
+	{0x7804, 0x04237040},
+	{0x5808, 0x04237040},
+	{0x7808, 0x04237040},
+	{0xB0000000, 0x00000000},
+	{0x12A0, 0x24903156},
+	{0x32A0, 0x24903156},
+	{0x640, 0x1414141E},
+	{0x12B8, 0x30020000},
+	{0x12AC, 0x02333121},
+	{0x9A4, 0x0000001C},
+	{0x624, 0x01010301},
+	{0x628, 0x00010101},
+	{0x5800, 0x03FF807F},
+	{0x7800, 0x03FF807F},
+	{0x4000, 0x00000000},
+	{0x4004, 0xCA014000},
+	{0x4008, 0xC751D4F0},
+	{0x400C, 0x44511475},
+	{0x4010, 0x00000000},
+	{0x4014, 0x00000000},
+	{0x4018, 0x4F4C084B},
+	{0x401C, 0x084A4E52},
+	{0x4020, 0x4D504E4B},
+	{0x4024, 0x4F4C0849},
+	{0x4028, 0x08484C50},
+	{0x402C, 0x4C50504C},
+	{0x4030, 0x5454084A},
+	{0x4034, 0x084B5654},
+	{0x4038, 0x6A6C605A},
+	{0x403C, 0x4C4C084C},
+	{0x4040, 0x084B4E4D},
+	{0x4044, 0x4E4C4B4B},
+	{0x4048, 0x4B4B084A},
+	{0x404C, 0x084A4E4C},
+	{0x4050, 0x514F4C4A},
+	{0x4054, 0x524E084A},
+	{0x4058, 0x084A5154},
+	{0x405C, 0x53555554},
+	{0x4060, 0x45450845},
+	{0x4064, 0x08454144},
+	{0x4068, 0x40434445},
+	{0x406C, 0x44450845},
+	{0x4070, 0x08444043},
+	{0x4074, 0x42434444},
+	{0x4078, 0x46450844},
+	{0x407C, 0x08444843},
+	{0x4080, 0x4B4E4A47},
+	{0x4084, 0x4F4C084B},
+	{0x4088, 0x084A4E52},
+	{0x408C, 0x4D504E4B},
+	{0x4090, 0x4F4C0849},
+	{0x4094, 0x08484C50},
+	{0x4098, 0x4C50504C},
+	{0x409C, 0x5454084A},
+	{0x40A0, 0x084B5654},
+	{0x40A4, 0x6A6C605A},
+	{0x40A8, 0x4C4C084C},
+	{0x40AC, 0x084B4E4D},
+	{0x40B0, 0x4E4C4B4B},
+	{0x40B4, 0x4B4B084A},
+	{0x40B8, 0x084A4E4C},
+	{0x40BC, 0x514F4C4A},
+	{0x40C0, 0x524E084A},
+	{0x40C4, 0x084A5154},
+	{0x40C8, 0x53555554},
+	{0x40CC, 0x45450845},
+	{0x40D0, 0x08454144},
+	{0x40D4, 0x40434445},
+	{0x40D8, 0x44450845},
+	{0x40DC, 0x08444043},
+	{0x40E0, 0x42434444},
+	{0x40E4, 0x46450844},
+	{0x40E8, 0x08444843},
+	{0x40EC, 0x4B4E4A47},
+	{0x40F0, 0x00000000},
+	{0x40F4, 0x00000006},
+	{0x40F8, 0x00000001},
+	{0x40FC, 0x8C30C30C},
+	{0x4100, 0x4C30C30C},
+	{0x4104, 0x0C30C30C},
+	{0x4108, 0x0C30C30C},
+	{0x410C, 0x0C30C30C},
+	{0x4110, 0x0C30C30C},
+	{0x4114, 0x28A28A28},
+	{0x4118, 0x28A28A28},
+	{0x411C, 0x28A28A28},
+	{0x4120, 0x28A28A28},
+	{0x4124, 0x28A28A28},
+	{0x4128, 0x28A28A28},
+	{0x412C, 0x06666666},
+	{0x4130, 0x33333333},
+	{0x4134, 0x33333333},
+	{0x4138, 0x33333333},
+	{0x413C, 0x00000031},
+	{0x4140, 0x5100600A},
+	{0x4144, 0x18363113},
+	{0x4148, 0x1D976DDC},
+	{0x414C, 0x1C072DD7},
+	{0x4150, 0x1127CDF4},
+	{0x4154, 0x1E37BDF1},
+	{0x4158, 0x1FB7F1D6},
+	{0x415C, 0x1EA7DDF9},
+	{0x4160, 0x1FE445DD},
+	{0x4164, 0x1F97F1FE},
+	{0x4168, 0x1FF781ED},
+	{0x416C, 0x1FA7F5FE},
+	{0x4170, 0x1E07B913},
+	{0x4174, 0x1FD7FDFF},
+	{0x4178, 0x1E17B9FA},
+	{0x417C, 0x19A66914},
+	{0x4180, 0x10F65598},
+	{0x4184, 0x14A5A111},
+	{0x4188, 0x1D3765DB},
+	{0x418C, 0x17C685CA},
+	{0x4190, 0x1107C5F3},
+	{0x4194, 0x1B5785EB},
+	{0x4198, 0x1F97ED8F},
+	{0x419C, 0x1BC7A5F3},
+	{0x41A0, 0x1FE43595},
+	{0x41A4, 0x1EB7D9FC},
+	{0x41A8, 0x1FE65DBE},
+	{0x41AC, 0x1EC7D9FC},
+	{0x41B0, 0x1976FCFF},
+	{0x41B4, 0x1F77F5FF},
+	{0x41B8, 0x1976FDEC},
+	{0x41BC, 0x198664EF},
+	{0x41C0, 0x11062D93},
+	{0x41C4, 0x10C4E910},
+	{0x41C8, 0x1CA759DB},
+	{0x41CC, 0x1335A9B5},
+	{0x41D0, 0x1097B9F3},
+	{0x41D4, 0x17B72DE1},
+	{0x41D8, 0x1F67ED42},
+	{0x41DC, 0x18074DE9},
+	{0x41E0, 0x1FD40547},
+	{0x41E4, 0x1D57ADF9},
+	{0x41E8, 0x1FE52182},
+	{0x41EC, 0x1D67B1F9},
+	{0x41F0, 0x14860CE1},
+	{0x41F4, 0x1EC7E9FE},
+	{0x41F8, 0x14860DD6},
+	{0x41FC, 0x195664C7},
+	{0x4200, 0x0005E58A},
+	{0x4204, 0x00000000},
+	{0x4208, 0x00000000},
+	{0x420C, 0x7A000000},
+	{0x4210, 0x0F9F3D7A},
+	{0x4214, 0x0040817C},
+	{0x4218, 0x00E10204},
+	{0x421C, 0x227D94CD},
+	{0x4220, 0x080238E3},
+	{0x4224, 0x00000210},
+	{0x4228, 0x04688000},
+	{0x422C, 0x0060B002},
+	{0x4230, 0x9A8249A8},
+	{0x4234, 0x26A1469E},
+	{0x4238, 0x2099A824},
+	{0x423C, 0x2359461C},
+	{0x4240, 0x1631A675},
+	{0x4244, 0x2C6B1D63},
+	{0x4248, 0x0000000E},
+	{0x424C, 0x00000001},
+	{0x4250, 0x00000001},
+	{0x4254, 0x00000000},
+	{0x4258, 0x00000000},
+	{0x425C, 0x00000000},
+	{0x4260, 0x0020000C},
+	{0x4264, 0x00000000},
+	{0x4268, 0x00000000},
+	{0x426C, 0x0418317C},
+	{0x4270, 0x00D6135C},
+	{0x4274, 0x00000000},
+	{0x4278, 0x00000000},
+	{0x427C, 0x00000000},
+	{0x4280, 0x00000000},
+	{0x4284, 0x00000000},
+	{0x4288, 0x00000000},
+	{0x428C, 0x00000000},
+	{0x4290, 0x00000000},
+	{0x4294, 0x00000000},
+	{0x4298, 0x84026000},
+	{0x429C, 0x0051AC20},
+	{0x42A0, 0x02024008},
+	{0x42A4, 0x00000000},
+	{0x42A8, 0x00000000},
+	{0x42AC, 0x22CE803C},
+	{0x42B0, 0x80000000},
+	{0x42B4, 0x00E7D03D},
+	{0x42B8, 0x3D67D67D},
+	{0x42BC, 0x7D67D65B},
+	{0x42C0, 0x2802AF59},
+	{0x42C4, 0x00280280},
+	{0x42C8, 0x00000000},
+	{0x42CC, 0x00000000},
+	{0x42D0, 0x00000003},
+	{0x42D4, 0x00000001},
+	{0x42D8, 0x61861800},
+	{0x42DC, 0x830C30C3},
+	{0x42E0, 0xC30C30C3},
+	{0x42E4, 0x830C30C3},
+	{0x42E8, 0x451450C3},
+	{0x42EC, 0x05145145},
+	{0x42F0, 0x05145145},
+	{0x42F4, 0x05145145},
+	{0x42F8, 0x0F0C3145},
+	{0x42FC, 0x030C30CF},
+	{0x4300, 0x030C30C3},
+	{0x4304, 0x030CF3C3},
+	{0x4308, 0x030C30C3},
+	{0x430C, 0x0F3CF3C3},
+	{0x4310, 0x0F3CF3CF},
+	{0x4314, 0x0F3CF3CF},
+	{0x4318, 0x0F3CF3CF},
+	{0x431C, 0x0F3CF3CF},
+	{0x4320, 0x030C10C3},
+	{0x4324, 0x051430C3},
+	{0x4328, 0x051490CB},
+	{0x432C, 0x030CD151},
+	{0x4330, 0x050C50C7},
+	{0x4334, 0x051492CB},
+	{0x4338, 0x05145145},
+	{0x433C, 0x05145145},
+	{0x4340, 0x05145145},
+	{0x4344, 0x05145145},
+	{0x4348, 0x090CD3CF},
+	{0x434C, 0x071491C5},
+	{0x4350, 0x073CF143},
+	{0x4354, 0x071431C3},
+	{0x4358, 0x0F3CF1C5},
+	{0x435C, 0x0F3CF3CF},
+	{0x4360, 0x0F3CF3CF},
+	{0x4364, 0x0F3CF3CF},
+	{0x4368, 0x0F3CF3CF},
+	{0x436C, 0x090C91CF},
+	{0x4370, 0x11243143},
+	{0x4374, 0x9777A777},
+	{0x4378, 0xBB7BAC95},
+	{0x437C, 0xB667B889},
+	{0x4380, 0x7B9B8899},
+	{0x4384, 0x7A5567C8},
+	{0x4388, 0x2278CCCC},
+	{0x438C, 0x7C222222},
+	{0x4390, 0x0000069B},
+	{0x4394, 0x001CCCCC},
+	{0x4398, 0x00000000},
+	{0x439C, 0x00000008},
+	{0x49A4, 0x00000000},
+	{0x43A0, 0x00000000},
+	{0x43A4, 0x00000000},
+	{0x43A8, 0x00000000},
+	{0x43AC, 0x10000800},
+	{0x43B0, 0x00401802},
+	{0x43B4, 0x00061004},
+	{0x43B8, 0x000024D8},
+	{0x43BC, 0x00000000},
+	{0x43C0, 0x10000020},
+	{0x43C4, 0x20000200},
+	{0x43C8, 0x00000000},
+	{0x43CC, 0x04000000},
+	{0x43D0, 0x44000100},
+	{0x43D4, 0x60804060},
+	{0x43D8, 0x44204210},
+	{0x43DC, 0x82108082},
+	{0x43E0, 0x82108402},
+	{0x43E4, 0xC8082108},
+	{0x43E8, 0xC8202084},
+	{0x43EC, 0x44208208},
+	{0x43F0, 0x84108204},
+	{0x43F4, 0xD0108104},
+	{0x43F8, 0xF8210108},
+	{0x43FC, 0x6431E930},
+	{0x4400, 0x02109468},
+	{0x4404, 0x10C61C22},
+	{0x4408, 0x02109469},
+	{0x440C, 0x10C61C22},
+	{0x4410, 0x00041049},
+	{0x4414, 0x00000000},
+	{0x4418, 0x00000000},
+	{0x441C, 0x6C000000},
+	{0x4420, 0xB0200020},
+	{0x4424, 0x00001FF0},
+	{0x4428, 0x00000000},
+	{0x442C, 0x00000000},
+	{0x4430, 0x00000000},
+	{0x4434, 0x00000000},
+	{0x4438, 0x65F962F8},
+	{0x443C, 0x280668A0},
+	{0x4440, 0x64100820},
+	{0x4444, 0x4A146304},
+	{0x4448, 0x0C59008F},
+	{0x444C, 0x6E30498A},
+	{0x4450, 0x656E371B},
+	{0x4454, 0x00000F52},
+	{0x4458, 0x00000000},
+	{0x445C, 0x4801442E},
+	{0x4460, 0x0041A0B8},
+	{0x4464, 0x00000000},
+	{0x4468, 0x00000000},
+	{0x446C, 0x00000000},
+	{0x4470, 0x00000000},
+	{0x4474, 0x00000000},
+	{0x4478, 0x00000000},
+	{0x447C, 0x00000000},
+	{0x4480, 0x2A0A6040},
+	{0x4484, 0x0A0A6829},
+	{0x4488, 0x00000004},
+	{0x448C, 0x00000000},
+	{0x4490, 0x80000000},
+	{0x4494, 0x10000000},
+	{0x4498, 0xA0000000},
+	{0x449C, 0x0000001E},
+	{0x44A0, 0x02B29397},
+	{0x44A4, 0x00000400},
+	{0x44A8, 0x00000001},
+	{0x44AC, 0x00000000},
+	{0x44B0, 0x00000000},
+	{0x44B4, 0x00000000},
+	{0x44B8, 0x00000000},
+	{0x44BC, 0x00000000},
+	{0x44C0, 0x00000000},
+	{0x44C4, 0x00000000},
+	{0x44C8, 0x00000000},
+	{0x44CC, 0x00000000},
+	{0x44D0, 0x00000000},
+	{0x44D4, 0x00000000},
+	{0x44D8, 0x00000000},
+	{0x44DC, 0x00000000},
+	{0x44E0, 0x00000000},
+	{0x44E4, 0x00000000},
+	{0x44E8, 0x00000000},
+	{0x44EC, 0x00000000},
+	{0x44F0, 0x00000000},
+	{0x44F4, 0x00000000},
+	{0x44F8, 0x00000000},
+	{0x44FC, 0x00000000},
+	{0x4500, 0x00000000},
+	{0x4504, 0x00000000},
+	{0x4508, 0x00000000},
+	{0x450C, 0x00000000},
+	{0x4510, 0x00000000},
+	{0x4514, 0x00000000},
+	{0x4518, 0x00000000},
+	{0x451C, 0x00000000},
+	{0x4520, 0x00000000},
+	{0x4524, 0x00000000},
+	{0x4528, 0x00000000},
+	{0x452C, 0x00000000},
+	{0x4530, 0x4EA20631},
+	{0x4534, 0x000005C8},
+	{0x4538, 0x000000FF},
+	{0x453C, 0x00000000},
+	{0x4540, 0x00000000},
+	{0x4544, 0x00000000},
+	{0x4548, 0x00000000},
+	{0x454C, 0x00000000},
+	{0x4550, 0x00000000},
+	{0x4554, 0x00000000},
+	{0x4558, 0x00000000},
+	{0x455C, 0x00000000},
+	{0x4560, 0x4060001A},
+	{0x4564, 0x40000000},
+	{0x4568, 0x00000000},
+	{0x456C, 0x20000000},
+	{0x4570, 0x04800406},
+	{0x4574, 0x00022270},
+	{0x4578, 0x0002024B},
+	{0x457C, 0x00200000},
+	{0x4580, 0x00009B40},
+	{0x4584, 0x00000000},
+	{0x4588, 0x00000063},
+	{0x458C, 0x30000000},
+	{0x4590, 0x00000000},
+	{0x4594, 0x05000000},
+	{0x4598, 0x00000001},
+	{0x459C, 0x0003FE00},
+	{0x45A0, 0x00000000},
+	{0x45A4, 0x00000000},
+	{0x45A8, 0xC00001C0},
+	{0x45AC, 0x78028000},
+	{0x45B0, 0x80000048},
+	{0x45B4, 0x01C90800},
+	{0x45B8, 0x00000002},
+	{0x45BC, 0x06748790},
+	{0x45C0, 0x80000000},
+	{0x45C4, 0x00000000},
+	{0x45C8, 0x00000000},
+	{0x45CC, 0x00558670},
+	{0x45D0, 0x002883F0},
+	{0x45D4, 0x00090120},
+	{0x45D8, 0x00000000},
+	{0x45DC, 0xA3A6D3C4},
+	{0x49A8, 0xAB27B126},
+	{0x49AC, 0x00006778},
+	{0x49FC, 0x000001B5},
+	{0x49B0, 0x11110F0A},
+	{0x49B4, 0x00000007},
+	{0x49B8, 0x0000000A},
+	{0x49BC, 0x0058BC3F},
+	{0x49C0, 0x00000003},
+	{0x49C4, 0x000003D9},
+	{0x49C8, 0x002B1CB0},
+	{0x4A00, 0x00000000},
+	{0x49CC, 0x00000001},
+	{0x49D0, 0x00000010},
+	{0x49D4, 0x00000001},
+	{0x49D8, 0x85298FBF},
+	{0x49DC, 0x18A5296E},
+	{0x49E0, 0x18C6298C},
+	{0x49E4, 0x0A739CA7},
+	{0x49E8, 0x001A50E7},
+	{0x49EC, 0x00000001},
+	{0x49F0, 0x00005924},
+	{0x49F4, 0x0003AAA6},
+	{0x49F8, 0x0000C4C3},
+	{0x45E0, 0x00000000},
+	{0x45E4, 0x00000000},
+	{0x45E8, 0x00E2E100},
+	{0x45EC, 0xCB00B6B6},
+	{0x45F0, 0x59100FCA},
+	{0x45F4, 0x08882550},
+	{0x45F8, 0x08CC2660},
+	{0x45FC, 0x09102660},
+	{0x4600, 0x00000154},
+	{0x4604, 0x00000800},
+	{0x4608, 0x31BF0400},
+	{0x460C, 0x00E0C0A0},
+	{0x4610, 0x30604020},
+	{0x4614, 0x2F346D50},
+	{0x4618, 0x2E36B6E2},
+	{0x461C, 0x3E7EF86B},
+	{0x4620, 0x001FC004},
+	{0x4624, 0xA8068010},
+	{0x4628, 0x4602CA80},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x462C, 0x76067E8C},
+	{0x4630, 0x8EA350E8},
+	{0x4634, 0xB3B8D8F5},
+	{0x4638, 0x6FFF0C06},
+	{0x463C, 0xB8FA4435},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x462C, 0x76078E8C},
+	{0x4630, 0x8EDB50F6},
+	{0x4634, 0xB5B8DD75},
+	{0x4638, 0x6FFF4C06},
+	{0x463C, 0xB8FA4434},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x462C, 0x76078E8C},
+	{0x4630, 0x8EDB50F6},
+	{0x4634, 0xB5B8DD75},
+	{0x4638, 0x6FFF4C06},
+	{0x463C, 0xB8FA4434},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x462C, 0x76067E8C},
+	{0x4630, 0x8EA350E8},
+	{0x4634, 0xB3B8D8F5},
+	{0x4638, 0x6FFF0C06},
+	{0x463C, 0xB8FA4435},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x462C, 0x76078E8C},
+	{0x4630, 0x8EDB50F6},
+	{0x4634, 0xB5B8DD75},
+	{0x4638, 0x6FFF4C06},
+	{0x463C, 0xB8FA4434},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x462C, 0x76078E8C},
+	{0x4630, 0x8EDB50F6},
+	{0x4634, 0xB5B8DD75},
+	{0x4638, 0x6FFF4C06},
+	{0x463C, 0xB8FA4434},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0xA0000000, 0x00000000},
+	{0x462C, 0x76067E8C},
+	{0x4630, 0x8EA350E8},
+	{0x4634, 0xB3B8D8F5},
+	{0x4638, 0x6FFF0C06},
+	{0x463C, 0xB8FA4435},
+	{0x4640, 0xB7C4FEF8},
+	{0x4644, 0x2A72AD07},
+	{0xB0000000, 0x00000000},
+	{0x4648, 0x64204FB2},
+	{0x464C, 0x4C823404},
+	{0x4650, 0x9084C800},
+	{0x4654, 0x9889314F},
+	{0x4658, 0x5ECC3FF4},
+	{0x465C, 0xFEECAECE},
+	{0x4660, 0x47806638},
+	{0x4664, 0x0F5AF843},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4668, 0x56452994},
+	{0x466C, 0x54D89ADB},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4668, 0x55452994},
+	{0x466C, 0x56D89ADB},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4668, 0x55452994},
+	{0x466C, 0x56D89ADB},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4668, 0x56452994},
+	{0x466C, 0x54D89ADB},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4668, 0x55452994},
+	{0x466C, 0x56D89ADB},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4668, 0x55452994},
+	{0x466C, 0x56D89ADB},
+	{0xA0000000, 0x00000000},
+	{0x4668, 0x56452994},
+	{0x466C, 0x54D89ADB},
+	{0xB0000000, 0x00000000},
+	{0x4670, 0xE8DF38D8},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4674, 0x002ACC30},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4674, 0x0028CC30},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4674, 0x0028CC30},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4674, 0x002ACC30},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4674, 0x0028CC30},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4674, 0x0028CC30},
+	{0xA0000000, 0x00000000},
+	{0x4674, 0x002ACC30},
+	{0xB0000000, 0x00000000},
+	{0x4678, 0x00000000},
+	{0x467C, 0x00000000},
+	{0x4680, 0x00000219},
+	{0x4684, 0x00000000},
+	{0x4688, 0x00000000},
+	{0x468C, 0x00000001},
+	{0x4690, 0x00000001},
+	{0x4694, 0x00000000},
+	{0x4698, 0x00000000},
+	{0x469C, 0x00000151},
+	{0x46A0, 0x00000498},
+	{0x46A4, 0x00000498},
+	{0x46A8, 0x00000000},
+	{0x46AC, 0x00000000},
+	{0x46B0, 0x00001146},
+	{0x46B4, 0x00000000},
+	{0x46B8, 0x00000000},
+	{0x46BC, 0x00E2E100},
+	{0x46C0, 0xCB00B6B6},
+	{0x46C4, 0x59100FCA},
+	{0x46C8, 0x08882550},
+	{0x46CC, 0x08CC2660},
+	{0x46D0, 0x09102660},
+	{0x46D4, 0x00000154},
+	{0x46D8, 0x00000800},
+	{0x46DC, 0x31BF0400},
+	{0x46E0, 0x00E0C0A0},
+	{0x46E4, 0x30604020},
+	{0x46E8, 0x4F346D50},
+	{0x46EC, 0x2E36B6E2},
+	{0x46F0, 0x3E7EF86B},
+	{0x46F4, 0x001FC004},
+	{0x46F8, 0xA8068010},
+	{0x46FC, 0x4602CA80},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4700, 0x7806FECC},
+	{0x4704, 0x8EC360F1},
+	{0x4708, 0xB4C4DA7A},
+	{0x470C, 0x72FF2CC6},
+	{0x4710, 0xB8FA4439},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4700, 0x78078ECC},
+	{0x4704, 0x8EDB60F6},
+	{0x4708, 0xB5C4DD7A},
+	{0x470C, 0x72FF4CC6},
+	{0x4710, 0xB8FA4434},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4700, 0x78078ECC},
+	{0x4704, 0x8EDB60F6},
+	{0x4708, 0xB5C4DD7A},
+	{0x470C, 0x72FF4CC6},
+	{0x4710, 0xB8FA4434},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4700, 0x7806FECC},
+	{0x4704, 0x8EC360F1},
+	{0x4708, 0xB4C4DA7A},
+	{0x470C, 0x72FF2CC6},
+	{0x4710, 0xB8FA4439},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4700, 0x78078ECC},
+	{0x4704, 0x8EDB60F6},
+	{0x4708, 0xB5C4DD7A},
+	{0x470C, 0x72FF4CC6},
+	{0x4710, 0xB8FA4434},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4700, 0x78078ECC},
+	{0x4704, 0x8EDB60F6},
+	{0x4708, 0xB5C4DD7A},
+	{0x470C, 0x72FF4CC6},
+	{0x4710, 0xB8FA4434},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0xA0000000, 0x00000000},
+	{0x4700, 0x7806FECC},
+	{0x4704, 0x8EC360F1},
+	{0x4708, 0xB4C4DA7A},
+	{0x470C, 0x72FF2CC6},
+	{0x4710, 0xB8FA4439},
+	{0x4714, 0xB7C4FEF8},
+	{0x4718, 0x2A72AD09},
+	{0xB0000000, 0x00000000},
+	{0x471C, 0x64204FB2},
+	{0x4720, 0x4C823404},
+	{0x4724, 0x9084C800},
+	{0x4728, 0x9889314F},
+	{0x472C, 0x5ECC3FF4},
+	{0x4730, 0xFEECAECE},
+	{0x4734, 0x47806638},
+	{0x4738, 0x0F4A7843},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x473C, 0x56452994},
+	{0x4740, 0x54D89ADB},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x473C, 0x55452994},
+	{0x4740, 0x56D89ADB},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x473C, 0x55452994},
+	{0x4740, 0x56D89ADB},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x473C, 0x56452994},
+	{0x4740, 0x54D89ADB},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x473C, 0x55452994},
+	{0x4740, 0x56D89ADB},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x473C, 0x55452994},
+	{0x4740, 0x56D89ADB},
+	{0xA0000000, 0x00000000},
+	{0x473C, 0x56452994},
+	{0x4740, 0x54D89ADB},
+	{0xB0000000, 0x00000000},
+	{0x4744, 0xE8DF38D8},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4748, 0x002ACC30},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4748, 0x0028CC30},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4748, 0x0028CC30},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4748, 0x002ACC30},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4748, 0x0028CC30},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x4748, 0x0028CC30},
+	{0xA0000000, 0x00000000},
+	{0x4748, 0x002ACC30},
+	{0xB0000000, 0x00000000},
+	{0x474C, 0x00000000},
+	{0x4750, 0x00000000},
+	{0x4754, 0x00000219},
+	{0x4758, 0x00000000},
+	{0x475C, 0x00000000},
+	{0x4760, 0x00000001},
+	{0x4764, 0x00000001},
+	{0x4768, 0x00000000},
+	{0x476C, 0x00000000},
+	{0x4770, 0x00000151},
+	{0x4774, 0x00000498},
+	{0x4778, 0x00000498},
+	{0x477C, 0x00000000},
+	{0x4780, 0x00000000},
+	{0x4784, 0x00001147},
+	{0x4788, 0x00000000},
+	{0x478C, 0xA32103FE},
+	{0x4790, 0x320A7B28},
+	{0x4794, 0xC6A7B14F},
+	{0x4798, 0x000006D7},
+	{0x479C, 0x009B902A},
+	{0x47A0, 0x009B902A},
+	{0x47A4, 0x98682C18},
+	{0x47A8, 0x6308C4C1},
+	{0x47AC, 0x6248C631},
+	{0x47B0, 0x922A8253},
+	{0x47B4, 0x00000005},
+	{0x47B8, 0x00001759},
+	{0x47BC, 0x4B802000},
+	{0x47C0, 0x831408BE},
+	{0x47C4, 0x9ABBCACB},
+	{0x47C8, 0x56767578},
+	{0x47CC, 0xBBCCBBB3},
+	{0x47D0, 0x57889989},
+	{0x47D4, 0x00000F45},
+	{0x47D8, 0x27039CE9},
+	{0x47DC, 0x31413432},
+	{0x47E0, 0x26058342},
+	{0x47E4, 0x00000006},
+	{0x47E8, 0x00000005},
+	{0x47EC, 0x00000005},
+	{0x47F0, 0xC7013016},
+	{0x47F4, 0x84413016},
+	{0x47F8, 0x84413016},
+	{0x47FC, 0x8C413016},
+	{0x4800, 0x8C40B028},
+	{0x4804, 0x3140B028},
+	{0x4808, 0x2940B028},
+	{0x480C, 0x8440B028},
+	{0x4810, 0x2318C610},
+	{0x4814, 0x45334753},
+	{0x4818, 0x236A6A88},
+	{0x481C, 0x576DF814},
+	{0x4820, 0xA08877AC},
+	{0x4824, 0x0000087A},
+	{0x4828, 0xBCEB4A14},
+	{0x482C, 0x000A3A4A},
+	{0x4830, 0xBCEB4A14},
+	{0x4834, 0x000A3A4A},
+	{0x4838, 0xBCBDBD85},
+	{0x483C, 0x0CABB99A},
+	{0x4840, 0x38384242},
+	{0x4844, 0x8086102E},
+	{0x4848, 0xCA24C82A},
+	{0x484C, 0x00008A62},
+	{0x4850, 0x00000008},
+	{0x4854, 0x009B902A},
+	{0x4858, 0x009B902A},
+	{0x485C, 0x98682C18},
+	{0x4860, 0x6308C4C1},
+	{0x4864, 0x6248C631},
+	{0x4868, 0x922A8253},
+	{0x486C, 0x00000005},
+	{0x4870, 0x00001759},
+	{0x4874, 0x4B802000},
+	{0x4878, 0x831408BE},
+	{0x487C, 0x9898A8BB},
+	{0x4880, 0x54535368},
+	{0x4884, 0x999999B3},
+	{0x4888, 0x35555589},
+	{0x488C, 0x00000745},
+	{0x4890, 0x27039CE9},
+	{0x4894, 0x31413432},
+	{0x4898, 0x26058342},
+	{0x489C, 0x00000006},
+	{0x48A0, 0x00000005},
+	{0x48A4, 0x00000005},
+	{0x48A8, 0xC7013016},
+	{0x48AC, 0x84413016},
+	{0x48B0, 0x84413016},
+	{0x48B4, 0x8C413016},
+	{0x48B8, 0x8C40B028},
+	{0x48BC, 0x3140B028},
+	{0x48C0, 0x2940B028},
+	{0x48C4, 0x8440B028},
+	{0x48C8, 0x2318C610},
+	{0x48CC, 0x45334753},
+	{0x48D0, 0x236A6A88},
+	{0x48D4, 0x576DF814},
+	{0x48D8, 0xA08877AC},
+	{0x48DC, 0x0000007A},
+	{0x48E0, 0xBCEB4A14},
+	{0x48E4, 0x000A3A4A},
+	{0x48E8, 0xBCEB4A14},
+	{0x48EC, 0x000A3A4A},
+	{0x48F0, 0x9A8A8A85},
+	{0x48F4, 0x0CA3B99A},
+	{0x48F8, 0x38384242},
+	{0x48FC, 0x8086102E},
+	{0x4900, 0xCA24C82A},
+	{0x4904, 0x00008A62},
+	{0x4908, 0x00000008},
+	{0x490C, 0x80040000},
+	{0x4910, 0x80040000},
+	{0x4914, 0xFE800000},
+	{0x4918, 0x834C0000},
+	{0x491C, 0x00000000},
+	{0x4920, 0x00000000},
+	{0x4924, 0x00000000},
+	{0x4928, 0x00000000},
+	{0x492C, 0x00000000},
+	{0x4930, 0x00000000},
+	{0x4934, 0x40000000},
+	{0x4938, 0x00000000},
+	{0x493C, 0x00000000},
+	{0x4940, 0x00000000},
+	{0x4944, 0x00000000},
+	{0x4948, 0x04065800},
+	{0x494C, 0x32004080},
+	{0x4950, 0x0E1E3E05},
+	{0x4954, 0x0A163068},
+	{0x4958, 0x00206040},
+	{0x495C, 0x02020202},
+	{0x4960, 0x00A16020},
+	{0x4964, 0x031F4284},
+	{0x4968, 0x00A10285},
+	{0x496C, 0x00000005},
+	{0x4970, 0x00000000},
+	{0x4974, 0x800CD62D},
+	{0x4978, 0x00000103},
+	{0x497C, 0x00000000},
+	{0x4980, 0x00000000},
+	{0x4984, 0x00000000},
+	{0x4988, 0x00000000},
+	{0x498C, 0x00000000},
+	{0x4990, 0x00000000},
+	{0x4994, 0x00000000},
+	{0x4998, 0x00000000},
+	{0x499C, 0x00000000},
+	{0x49A0, 0x00000000},
+	{0x2404, 0x00000001},
+	{0xC7C, 0x0000BFE0},
+	{0x020, 0x0000F381},
+	{0x024, 0x0000F381},
+	{0x028, 0x0000F381},
+	{0x02C, 0x0000F381},
+	{0xD78, 0x00000005},
+	{0x12CC, 0x00000CC1},
+	{0x12D0, 0x00000000},
+	{0x12D4, 0x00000000},
+	{0x12D8, 0x00000040},
+	{0x12DC, 0x4486888C},
+	{0x12E0, 0xC43A10E1},
+	{0x12E4, 0x30D52C68},
+	{0x12E8, 0x02024128},
+	{0x12EC, 0x888C272B},
+	{0x12EC, 0x888CA72B},
+	{0x32CC, 0x00000CC1},
+	{0x32D0, 0x00000000},
+	{0x32D4, 0x00000000},
+	{0x32D8, 0x00000040},
+	{0x32DC, 0x4486888C},
+	{0x32E0, 0xC43A10E1},
+	{0x32E4, 0x30D52C68},
+	{0x32E8, 0x02024128},
+	{0x32EC, 0x888C272B},
+	{0x32EC, 0x888CA72B},
+	{0x12AC, 0x12333121},
+	{0x32AC, 0x12333121},
+	{0x738, 0x004100CC},
+	{0x80ff0001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5820, 0x80001080},
+	{0x7820, 0x80001080},
+	{0x903300ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5820, 0xC0001080},
+	{0x7820, 0xC0001080},
+	{0x903500ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5820, 0xC0001080},
+	{0x7820, 0xC0001080},
+	{0x903200ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5820, 0x80001080},
+	{0x7820, 0x80001080},
+	{0x903400ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5820, 0x80001080},
+	{0x7820, 0x80001080},
+	{0x903600ff, 0x00000000}, {0x40000000, 0x00000000},
+	{0x5820, 0x80001080},
+	{0x7820, 0x80001080},
+	{0xA0000000, 0x00000000},
+	{0x5820, 0x80001080},
+	{0x7820, 0x80001080},
+	{0xB0000000, 0x00000000},
+	{0x2000, 0x18BBBF84},
+	{0x0F0, 0x00000002},
+	{0x0F4, 0x00000016},
+	{0x0F8, 0x20201013},
+};
+
+static const struct rtw89_reg2_def rtw89_8852a_phy_radioa_regs[] = {
+	{0xF0010000, 0x00000000},
+	{0xF0010001, 0x00000001},
+	{0xF0020001, 0x00000002},
+	{0xF0030001, 0x00000003},
+	{0xF0250001, 0x00000004},
+	{0xF0260001, 0x00000005},
+	{0xF0320001, 0x00000006},
+	{0xF0330001, 0x00000007},
+	{0xF0340001, 0x00000008},
+	{0xF0350001, 0x00000009},
+	{0xF0360001, 0x0000000A},
+	{0xF0010002, 0x0000000B},
+	{0xF0020002, 0x0000000C},
+	{0xF0030002, 0x0000000D},
+	{0xF0250002, 0x0000000E},
+	{0xF0260002, 0x0000000F},
+	{0xF0320002, 0x00000010},
+	{0xF0330002, 0x00000011},
+	{0xF0340002, 0x00000012},
+	{0xF0350002, 0x00000013},
+	{0xF0360002, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000001},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x005, 0x00000001},
+	{0xB0000000, 0x00000000},
+	{0x000, 0x00030000},
+	{0x018, 0x00011124},
+	{0x000, 0x00033C00},
+	{0x01A, 0x00040004},
+	{0x0FE, 0x00000000},
+	{0x055, 0x00080000},
+	{0x056, 0x0008FFF0},
+	{0x057, 0x0000C485},
+	{0x058, 0x000A4164},
+	{0x059, 0x00010000},
+	{0x05A, 0x00060000},
+	{0x05B, 0x0000A000},
+	{0x05C, 0x00000000},
+	{0x05D, 0x0001C013},
+	{0x05E, 0x00000000},
+	{0x05F, 0x00001FF0},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0xA0000000, 0x00000000},
+	{0x060, 0x00011000},
+	{0xB0000000, 0x00000000},
+	{0x061, 0x0009F338},
+	{0x062, 0x0009233A},
+	{0x063, 0x000D6002},
+	{0x064, 0x000A0CB0},
+	{0x065, 0x00030EFE},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0xA0000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0xB0000000, 0x00000000},
+	{0x068, 0x00000000},
+	{0x069, 0x00030F0A},
+	{0x06A, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000AD6A4},
+	{0x052, 0x00091345},
+	{0x053, 0x00080081},
+	{0x054, 0x0009BC24},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0xA0000000, 0x00000000},
+	{0x051, 0x000AD6A4},
+	{0x052, 0x00091345},
+	{0x053, 0x00080081},
+	{0x054, 0x0009BC24},
+	{0xB0000000, 0x00000000},
+	{0x0D3, 0x00000143},
+	{0x043, 0x00005000},
+	{0x0DD, 0x000003A0},
+	{0x0B0, 0x000E6700},
+	{0x0AF, 0x0001F82E},
+	{0x0B2, 0x000210A7},
+	{0x0B1, 0x00065FFF},
+	{0x0BB, 0x000F7A00},
+	{0x0B3, 0x00013F7A},
+	{0x0D4, 0x0000000E},
+	{0x0B7, 0x00001E0C},
+	{0x0A0, 0x0000004F},
+	{0x0B4, 0x0007C03E},
+	{0x0B5, 0x0007E301},
+	{0x0B6, 0x00080800},
+	{0x0CA, 0x00002000},
+	{0x0DD, 0x000003A0},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x00080000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0xA0000000, 0x00000000},
+	{0x0CC, 0x00080000},
+	{0xB0000000, 0x00000000},
+	{0x0A1, 0x0006F300},
+	{0x0A2, 0x00080500},
+	{0x0A3, 0x0008050B},
+	{0x0A4, 0x0006DB12},
+	{0x0A5, 0x00000000},
+	{0x0A6, 0x00000000},
+	{0x0A7, 0x00000000},
+	{0x0A8, 0x00000000},
+	{0x0A9, 0x00000000},
+	{0x0AA, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x000B0000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0A5, 0x000B0000},
+	{0xB0000000, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00008000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0ED, 0x00008000},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000000},
+	{0x03E, 0x00008000},
+	{0x03F, 0x000E1333},
+	{0x033, 0x00000001},
+	{0x03E, 0x00008000},
+	{0x03F, 0x000E7333},
+	{0x033, 0x00000002},
+	{0x03E, 0x00008000},
+	{0x03F, 0x000FA000},
+	{0x033, 0x00000003},
+	{0x03E, 0x00004000},
+	{0x03F, 0x000FA400},
+	{0x033, 0x00000004},
+	{0x03E, 0x00004000},
+	{0x03F, 0x000F5000},
+	{0x033, 0x00000005},
+	{0x03E, 0x00004001},
+	{0x03F, 0x00029400},
+	{0x033, 0x00000006},
+	{0x03E, 0x0000AAA1},
+	{0x03F, 0x00041999},
+	{0x033, 0x00000007},
+	{0x03E, 0x0000AAA1},
+	{0x03F, 0x00034444},
+	{0x033, 0x00000008},
+	{0x03E, 0x0000AAA1},
+	{0x03F, 0x0004D555},
+	{0x033, 0x00000009},
+	{0x03E, 0x00005551},
+	{0x03F, 0x00046AAA},
+	{0x033, 0x0000000A},
+	{0x03E, 0x00005551},
+	{0x03F, 0x00046AAA},
+	{0x033, 0x0000000B},
+	{0x03E, 0x00005551},
+	{0x03F, 0x0008C555},
+	{0x033, 0x0000000C},
+	{0x03E, 0x0000CCC1},
+	{0x03F, 0x00081EB8},
+	{0x033, 0x0000000D},
+	{0x03E, 0x0000CCC1},
+	{0x03F, 0x00071EB8},
+	{0x033, 0x0000000E},
+	{0x03E, 0x0000CCC1},
+	{0x03F, 0x00090000},
+	{0x033, 0x0000000F},
+	{0x03E, 0x00006661},
+	{0x03F, 0x00088000},
+	{0x033, 0x00000010},
+	{0x03E, 0x00006661},
+	{0x03F, 0x00088000},
+	{0x033, 0x00000011},
+	{0x03E, 0x00006661},
+	{0x03F, 0x000DB999},
+	{0x0ED, 0x00000000},
+	{0x0ED, 0x00002000},
+	{0x033, 0x00000002},
+	{0x03D, 0x0004A883},
+	{0x03E, 0x00000000},
+	{0x03F, 0x00000001},
+	{0x033, 0x00000006},
+	{0x03D, 0x0004A883},
+	{0x03E, 0x00000000},
+	{0x03F, 0x00000001},
+	{0x0ED, 0x00000000},
+	{0x018, 0x00001001},
+	{0x002, 0x0000000D},
+	{0x0EE, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0xA0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0xB0000000, 0x00000000},
+	{0x0EE, 0x00000000},
+	{0x08F, 0x000D0F7A},
+	{0x08C, 0x00084584},
+	{0x0EF, 0x00004000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000500},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000500},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00008B00},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00008B00},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00001000},
+	{0x033, 0x00000000},
+	{0x03F, 0x00000015},
+	{0x033, 0x00000001},
+	{0x03F, 0x00000017},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00008000},
+	{0x033, 0x00000000},
+	{0x03F, 0x000FECFC},
+	{0x033, 0x00000001},
+	{0x03F, 0x000BECFC},
+	{0x033, 0x00000002},
+	{0x03F, 0x0003E4FC},
+	{0x033, 0x00000003},
+	{0x03F, 0x0001D0FC},
+	{0x033, 0x00000004},
+	{0x03F, 0x0001C3FC},
+	{0x033, 0x00000005},
+	{0x03F, 0x000103FC},
+	{0x033, 0x00000006},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000007},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000008},
+	{0x03F, 0x000FECFC},
+	{0x033, 0x00000009},
+	{0x03F, 0x000BECFC},
+	{0x033, 0x0000000A},
+	{0x03F, 0x0003E4FC},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0001D0FC},
+	{0x033, 0x0000000C},
+	{0x03F, 0x0001C3FC},
+	{0x033, 0x0000000D},
+	{0x03F, 0x000103FC},
+	{0x033, 0x0000000E},
+	{0x03F, 0x0000007C},
+	{0x033, 0x0000000F},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000010},
+	{0x03F, 0x000FECFC},
+	{0x033, 0x00000011},
+	{0x03F, 0x000BECFC},
+	{0x033, 0x00000012},
+	{0x03F, 0x0003E4FC},
+	{0x033, 0x00000013},
+	{0x03F, 0x0001D0FC},
+	{0x033, 0x00000014},
+	{0x03F, 0x0001C3FC},
+	{0x033, 0x00000015},
+	{0x03F, 0x000103FC},
+	{0x033, 0x00000016},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000017},
+	{0x03F, 0x0000007C},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000100},
+	{0x033, 0x00000000},
+	{0x03F, 0x00003317},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x03F, 0x00003317},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x03F, 0x00003317},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001A},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001B},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001C},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001D},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001E},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001F},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000020},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000021},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000022},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000023},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000024},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000025},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000026},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000027},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000028},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000029},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002A},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002B},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002C},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002D},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002E},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002F},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000030},
+	{0x03F, 0x00003338},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000040},
+	{0x033, 0x00000001},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000002},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000003},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000004},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000005},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000006},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000007},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000008},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000009},
+	{0x03F, 0x000004BA},
+	{0x033, 0x0000000A},
+	{0x03F, 0x000004BA},
+	{0x033, 0x0000000B},
+	{0x03F, 0x000004BA},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000010},
+	{0x033, 0x00000001},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000002},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000003},
+	{0x03F, 0x00000870},
+	{0x033, 0x00000004},
+	{0x03F, 0x00000870},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000008},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000009},
+	{0x03F, 0x00000870},
+	{0x033, 0x0000000A},
+	{0x03F, 0x00000870},
+	{0x033, 0x0000000B},
+	{0x03F, 0x00000430},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000430},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x03F, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000080},
+	{0x033, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F358},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F358},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00023458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00023858},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x03E, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00023758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002E758},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000023},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000024},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000025},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000026},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000027},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002E658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00027758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C758},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000E},
+	{0x03F, 0x0002F658},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EE, 0x00002000},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000068},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000068},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000023},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000024},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000025},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000026},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000027},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000040},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000041},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000042},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000043},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000044},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000045},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000046},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000047},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000048},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000049},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000050},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000051},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000052},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000053},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000054},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000055},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000056},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000057},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000058},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000059},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000060},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000061},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000062},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000063},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000064},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000065},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000066},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000067},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000068},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000069},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000070},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000071},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000072},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000073},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000074},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000075},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000076},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000077},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000078},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000079},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000080},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000081},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000082},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000083},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000084},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000085},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000086},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000087},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x0EE, 0x00000000},
+	{0x0EE, 0x00004000},
+	{0x033, 0x00000000},
+	{0x03F, 0x00003BEF},
+	{0x033, 0x00000001},
+	{0x03F, 0x00003BE9},
+	{0x033, 0x00000002},
+	{0x03F, 0x00003BE3},
+	{0x033, 0x00000003},
+	{0x03F, 0x00003BDD},
+	{0x033, 0x00000004},
+	{0x03F, 0x00003BD7},
+	{0x033, 0x00000005},
+	{0x03F, 0x00003BD1},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00001BD9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000BD9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000859},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000859},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000819},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000819},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x03F, 0x000039EE},
+	{0x033, 0x00000013},
+	{0x03F, 0x000039E8},
+	{0x033, 0x00000014},
+	{0x03F, 0x000039E2},
+	{0x033, 0x00000015},
+	{0x03F, 0x000039DC},
+	{0x033, 0x00000016},
+	{0x03F, 0x000039D6},
+	{0x033, 0x00000017},
+	{0x03F, 0x000039D0},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x03F, 0x000019D2},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x03F, 0x000009D2},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x03F, 0x000008D3},
+	{0x033, 0x0000001E},
+	{0x03F, 0x000008CD},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000023},
+	{0x03F, 0x00000807},
+	{0x033, 0x00000024},
+	{0x03F, 0x000039EE},
+	{0x033, 0x00000025},
+	{0x03F, 0x000039E8},
+	{0x033, 0x00000026},
+	{0x03F, 0x000039E2},
+	{0x033, 0x00000027},
+	{0x03F, 0x000039DC},
+	{0x033, 0x00000028},
+	{0x03F, 0x000039D6},
+	{0x033, 0x00000029},
+	{0x03F, 0x000039D0},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x03F, 0x000019D2},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x03F, 0x000009D2},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000030},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000035},
+	{0x03F, 0x00000807},
+	{0x033, 0x00000036},
+	{0x03F, 0x000039EE},
+	{0x033, 0x00000037},
+	{0x03F, 0x000039E8},
+	{0x033, 0x00000038},
+	{0x03F, 0x000039E2},
+	{0x033, 0x00000039},
+	{0x03F, 0x000039DC},
+	{0x033, 0x0000003A},
+	{0x03F, 0x000039D6},
+	{0x033, 0x0000003B},
+	{0x03F, 0x000039D0},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x03F, 0x000019D2},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x03F, 0x000009D2},
+	{0x033, 0x00000040},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000041},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000042},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000043},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000044},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000045},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000046},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000047},
+	{0x03F, 0x00000807},
+	{0x033, 0x00000048},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000049},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000050},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000051},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000052},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000053},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000054},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000055},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000056},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000057},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000058},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000059},
+	{0x03F, 0x00000807},
+	{0x033, 0x0000005A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000060},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000061},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000062},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000063},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000064},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000065},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000066},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000067},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000068},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000069},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006A},
+	{0x03F, 0x0000080D},
+	{0x033, 0x0000006B},
+	{0x03F, 0x00000807},
+	{0x033, 0x0000006C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000070},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000071},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000072},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000073},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000074},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000075},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000076},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000077},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000078},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000079},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007A},
+	{0x03F, 0x0000084D},
+	{0x033, 0x0000007B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007C},
+	{0x03F, 0x0000080D},
+	{0x033, 0x0000007D},
+	{0x03F, 0x00000807},
+	{0x033, 0x0000007E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000080},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000081},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000082},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000083},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000084},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000085},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000086},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000087},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000088},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000089},
+	{0x03F, 0x000008D3},
+	{0x033, 0x0000008A},
+	{0x03F, 0x000008CD},
+	{0x033, 0x0000008B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000008C},
+	{0x03F, 0x0000084D},
+	{0x033, 0x0000008D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000008E},
+	{0x03F, 0x0000080D},
+	{0x033, 0x0000008F},
+	{0x03F, 0x00000807},
+	{0x0EE, 0x00000000},
+	{0x0EF, 0x00080000},
+	{0x033, 0x00000007},
+	{0x03E, 0x00000001},
+	{0x03F, 0x00020F3C},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00080000},
+	{0x033, 0x0000000C},
+	{0x03E, 0x00000001},
+	{0x03F, 0x000305BC},
+	{0x0EF, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000001},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0EC, 0x00000001},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x03C, 0x00000020},
+	{0x03D, 0x00000078},
+	{0x03E, 0x00080000},
+	{0x03F, 0x00001999},
+	{0x0EC, 0x00000000},
+	{0x02F, 0x0002260D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000001},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0DE, 0x00000001},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000002},
+	{0x033, 0x00000000},
+	{0x03F, 0x00000002},
+	{0x033, 0x00000001},
+	{0x03F, 0x00000002},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000400},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000023},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000024},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000025},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000026},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000027},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000200},
+	{0x033, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000001},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000002},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000003},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000004},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000005},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000006},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000007},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000008},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000009},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000A},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000B},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000C},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000D},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000E},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000F},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000010},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000011},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000012},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000013},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000014},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000015},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000016},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000017},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000018},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000019},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001A},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001B},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001C},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001D},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001E},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001F},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000020},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000021},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000022},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000023},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000024},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000025},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000026},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000027},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0xA0000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0xB0000000, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0xA0000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0xB0000000, 0x00000000},
+	{0x06D, 0x00000C31},
+	{0x0EF, 0x00020000},
+	{0x033, 0x00000000},
+	{0x03F, 0x000005FF},
+	{0x0EF, 0x00000000},
+	{0x005, 0x00000001},
+	{0x0EF, 0x00080000},
+	{0x033, 0x00000001},
+	{0x03E, 0x00000001},
+	{0x03F, 0x00022020},
+	{0x0EF, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0xA0000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0xB0000000, 0x00000000},
+	{0x002, 0x00000000},
+	{0x067, 0x00000052},
+
+};
+
+static const struct rtw89_reg2_def rtw89_8852a_phy_radiob_regs[] = {
+	{0xF0010000, 0x00000000},
+	{0xF0010001, 0x00000001},
+	{0xF0020001, 0x00000002},
+	{0xF0030001, 0x00000003},
+	{0xF0250001, 0x00000004},
+	{0xF0260001, 0x00000005},
+	{0xF0320001, 0x00000006},
+	{0xF0330001, 0x00000007},
+	{0xF0340001, 0x00000008},
+	{0xF0350001, 0x00000009},
+	{0xF0360001, 0x0000000A},
+	{0xF0010002, 0x0000000B},
+	{0xF0020002, 0x0000000C},
+	{0xF0030002, 0x0000000D},
+	{0xF0250002, 0x0000000E},
+	{0xF0260002, 0x0000000F},
+	{0xF0320002, 0x00000010},
+	{0xF0330002, 0x00000011},
+	{0xF0340002, 0x00000012},
+	{0xF0350002, 0x00000013},
+	{0xF0360002, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000001},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x005, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x005, 0x00000001},
+	{0xB0000000, 0x00000000},
+	{0x000, 0x00030000},
+	{0x018, 0x00011124},
+	{0x000, 0x00033C00},
+	{0x01A, 0x00040004},
+	{0x0FE, 0x00000000},
+	{0x055, 0x00080000},
+	{0x056, 0x0008FFF0},
+	{0x057, 0x0000C485},
+	{0x058, 0x000A4164},
+	{0x059, 0x00010000},
+	{0x05A, 0x00060000},
+	{0x05B, 0x0000A000},
+	{0x05C, 0x00000000},
+	{0x05D, 0x0001C013},
+	{0x05E, 0x00000000},
+	{0x05F, 0x00001FF0},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x060, 0x00011008},
+	{0xA0000000, 0x00000000},
+	{0x060, 0x00011000},
+	{0xB0000000, 0x00000000},
+	{0x061, 0x0009F338},
+	{0x062, 0x0009233A},
+	{0x063, 0x000D6002},
+	{0x064, 0x000A0CB0},
+	{0x065, 0x00030EFE},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x066, 0x00020000},
+	{0xA0000000, 0x00000000},
+	{0x066, 0x00010000},
+	{0xB0000000, 0x00000000},
+	{0x068, 0x00000000},
+	{0x069, 0x00030F0A},
+	{0x06A, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000AD6A4},
+	{0x052, 0x00091345},
+	{0x053, 0x00080081},
+	{0x054, 0x0007BC24},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x051, 0x000BD267},
+	{0x052, 0x00091345},
+	{0x053, 0x000B0081},
+	{0x054, 0x0007BCA4},
+	{0xA0000000, 0x00000000},
+	{0x051, 0x000AD6A4},
+	{0x052, 0x00091345},
+	{0x053, 0x00080081},
+	{0x054, 0x0007BC24},
+	{0xB0000000, 0x00000000},
+	{0x0D3, 0x00000143},
+	{0x043, 0x00005000},
+	{0x0DD, 0x000003A0},
+	{0x0B0, 0x000E6700},
+	{0x0AF, 0x0001F82E},
+	{0x0B2, 0x000210A7},
+	{0x0B1, 0x00065FFF},
+	{0x0BB, 0x000F7A00},
+	{0x0B3, 0x00013F7A},
+	{0x0D4, 0x0000000E},
+	{0x0B7, 0x00001E0C},
+	{0x0A0, 0x0000004F},
+	{0x0B4, 0x0007C03E},
+	{0x0B5, 0x0007E301},
+	{0x0B6, 0x00080800},
+	{0x0CA, 0x00002000},
+	{0x0DD, 0x000003A0},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x00080000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0CC, 0x000E0000},
+	{0xA0000000, 0x00000000},
+	{0x0CC, 0x00080000},
+	{0xB0000000, 0x00000000},
+	{0x0A1, 0x0006F300},
+	{0x0A2, 0x00080500},
+	{0x0A3, 0x0008050B},
+	{0x0A4, 0x0006DB12},
+	{0x0A5, 0x00000000},
+	{0x0A6, 0x00000000},
+	{0x0A7, 0x00000000},
+	{0x0A8, 0x00000000},
+	{0x0A9, 0x00000000},
+	{0x0AA, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x000B0000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0A5, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0A5, 0x000B0000},
+	{0xB0000000, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00008000},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0ED, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0ED, 0x00008000},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000000},
+	{0x03E, 0x00008000},
+	{0x03F, 0x000E1333},
+	{0x033, 0x00000001},
+	{0x03E, 0x00008000},
+	{0x03F, 0x000E7333},
+	{0x033, 0x00000002},
+	{0x03E, 0x00008000},
+	{0x03F, 0x000FA000},
+	{0x033, 0x00000003},
+	{0x03E, 0x00004000},
+	{0x03F, 0x000FA400},
+	{0x033, 0x00000004},
+	{0x03E, 0x00004000},
+	{0x03F, 0x000F5000},
+	{0x033, 0x00000005},
+	{0x03E, 0x00004001},
+	{0x03F, 0x00029400},
+	{0x033, 0x00000006},
+	{0x03E, 0x0000AAA1},
+	{0x03F, 0x00041999},
+	{0x033, 0x00000007},
+	{0x03E, 0x0000AAA1},
+	{0x03F, 0x00034444},
+	{0x033, 0x00000008},
+	{0x03E, 0x0000AAA1},
+	{0x03F, 0x0004D555},
+	{0x033, 0x00000009},
+	{0x03E, 0x00005551},
+	{0x03F, 0x00046AAA},
+	{0x033, 0x0000000A},
+	{0x03E, 0x00005551},
+	{0x03F, 0x00046AAA},
+	{0x033, 0x0000000B},
+	{0x03E, 0x00005551},
+	{0x03F, 0x0008C555},
+	{0x033, 0x0000000C},
+	{0x03E, 0x0000CCC1},
+	{0x03F, 0x00081EB8},
+	{0x033, 0x0000000D},
+	{0x03E, 0x0000CCC1},
+	{0x03F, 0x00071EB8},
+	{0x033, 0x0000000E},
+	{0x03E, 0x0000CCC1},
+	{0x03F, 0x00090000},
+	{0x033, 0x0000000F},
+	{0x03E, 0x00006661},
+	{0x03F, 0x00088000},
+	{0x033, 0x00000010},
+	{0x03E, 0x00006661},
+	{0x03F, 0x00088000},
+	{0x033, 0x00000011},
+	{0x03E, 0x00006661},
+	{0x03F, 0x000DB999},
+	{0x0ED, 0x00000000},
+	{0x0ED, 0x00002000},
+	{0x033, 0x00000002},
+	{0x03D, 0x0004A883},
+	{0x03E, 0x00000000},
+	{0x03F, 0x00000001},
+	{0x033, 0x00000006},
+	{0x03D, 0x0004A883},
+	{0x03E, 0x00000000},
+	{0x03F, 0x00000001},
+	{0x0ED, 0x00000000},
+	{0x018, 0x00001001},
+	{0x002, 0x0000000D},
+	{0x0EE, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000A},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000011},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000018},
+	{0xA0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0000000B},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000012},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000019},
+	{0xB0000000, 0x00000000},
+	{0x0EE, 0x00000000},
+	{0x08F, 0x000D0F7A},
+	{0x08C, 0x00084584},
+	{0x0EF, 0x00004000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004700},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000700},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000500},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000B0600},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00094600},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000500},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4500},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000400},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00008B00},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00038B00},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000D4400},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00008B00},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00014B00},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000B00},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004A00},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00001A00},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00004900},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00002900},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00001000},
+	{0x033, 0x00000000},
+	{0x03F, 0x00000015},
+	{0x033, 0x00000001},
+	{0x03F, 0x00000017},
+	{0x033, 0x00000002},
+	{0x03F, 0x00000015},
+	{0x033, 0x00000003},
+	{0x03F, 0x00000017},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00008000},
+	{0x033, 0x00000000},
+	{0x03F, 0x000FECFC},
+	{0x033, 0x00000001},
+	{0x03F, 0x000BECFC},
+	{0x033, 0x00000002},
+	{0x03F, 0x0003E4FC},
+	{0x033, 0x00000003},
+	{0x03F, 0x0001D0FC},
+	{0x033, 0x00000004},
+	{0x03F, 0x0001C3FC},
+	{0x033, 0x00000005},
+	{0x03F, 0x000103FC},
+	{0x033, 0x00000006},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000007},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000008},
+	{0x03F, 0x000FECFC},
+	{0x033, 0x00000009},
+	{0x03F, 0x000BECFC},
+	{0x033, 0x0000000A},
+	{0x03F, 0x0003E4FC},
+	{0x033, 0x0000000B},
+	{0x03F, 0x0001D0FC},
+	{0x033, 0x0000000C},
+	{0x03F, 0x0001C3FC},
+	{0x033, 0x0000000D},
+	{0x03F, 0x000103FC},
+	{0x033, 0x0000000E},
+	{0x03F, 0x0000007C},
+	{0x033, 0x0000000F},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000010},
+	{0x03F, 0x000FECFC},
+	{0x033, 0x00000011},
+	{0x03F, 0x000BECFC},
+	{0x033, 0x00000012},
+	{0x03F, 0x0003E4FC},
+	{0x033, 0x00000013},
+	{0x03F, 0x0001D0FC},
+	{0x033, 0x00000014},
+	{0x03F, 0x0001C3FC},
+	{0x033, 0x00000015},
+	{0x03F, 0x000103FC},
+	{0x033, 0x00000016},
+	{0x03F, 0x0000007C},
+	{0x033, 0x00000017},
+	{0x03F, 0x0000007C},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000100},
+	{0x033, 0x00000000},
+	{0x03F, 0x00003317},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x03F, 0x00003317},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x03F, 0x00003317},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003336},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003338},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003337},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00003356},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001A},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001B},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001C},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001D},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001E},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000001F},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000020},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000021},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000022},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000023},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000024},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000025},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000026},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000027},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000028},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000029},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002A},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002B},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002C},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002D},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002E},
+	{0x03F, 0x00003338},
+	{0x033, 0x0000002F},
+	{0x03F, 0x00003338},
+	{0x033, 0x00000030},
+	{0x03F, 0x00003338},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000040},
+	{0x033, 0x00000001},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000002},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000003},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000004},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000005},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000006},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000007},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000008},
+	{0x03F, 0x000004BA},
+	{0x033, 0x00000009},
+	{0x03F, 0x000004BA},
+	{0x033, 0x0000000A},
+	{0x03F, 0x000004BA},
+	{0x033, 0x0000000B},
+	{0x03F, 0x000004BA},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000010},
+	{0x033, 0x00000001},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000002},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000003},
+	{0x03F, 0x00000870},
+	{0x033, 0x00000004},
+	{0x03F, 0x00000870},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000730},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000430},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000008},
+	{0x03F, 0x00000CB0},
+	{0x033, 0x00000009},
+	{0x03F, 0x00000870},
+	{0x033, 0x0000000A},
+	{0x03F, 0x00000870},
+	{0x033, 0x0000000B},
+	{0x03F, 0x00000430},
+	{0x033, 0x0000000C},
+	{0x03F, 0x00000430},
+	{0x033, 0x0000000D},
+	{0x03F, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x03F, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000080},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F258},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F258},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00036458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0003C458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026658},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00026458},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00028558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C358},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0002C558},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000023},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000024},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000025},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000026},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000027},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F358},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002F358},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F258},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023758},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00023558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00025558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x00024558},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000C},
+	{0x03F, 0x0002C558},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xA0000000, 0x00000000},
+	{0x03E, 0x0000000B},
+	{0x03F, 0x0006F458},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EE, 0x00002000},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000166},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000163},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000068},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000068},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F5},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F2},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A5},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A2},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000053},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000023},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000024},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000025},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000026},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000027},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000070},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000067},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000064},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000061},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000058},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E5},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000055},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000E2},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000052},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000DF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000065},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000062},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000040},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000049},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000041},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000046},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000042},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000043},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000059},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000043},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000040},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000056},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000044},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000045},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000046},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000047},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000048},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000049},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000050},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000051},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000052},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000053},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000054},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000055},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000056},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000057},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000058},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000059},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000060},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000061},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000062},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000063},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000064},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000065},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000066},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000067},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000068},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000069},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000070},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000071},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000072},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000073},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000074},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000075},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000076},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000077},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000078},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000078},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000075},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000079},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000072},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F6},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001EA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001F0},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001E4},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001ED},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AC},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001AA},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000E0},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000080},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001A4},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000081},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000006C},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000082},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000069},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000083},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000066},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000084},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000063},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000085},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004E},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000057},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000060},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000086},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000004B},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000054},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005D},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000087},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000048},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000051},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000005A},
+	{0xB0000000, 0x00000000},
+	{0x0EE, 0x00000000},
+	{0x0EE, 0x00004000},
+	{0x033, 0x00000000},
+	{0x03F, 0x00003BEF},
+	{0x033, 0x00000001},
+	{0x03F, 0x00003BE9},
+	{0x033, 0x00000002},
+	{0x03F, 0x00003BE3},
+	{0x033, 0x00000003},
+	{0x03F, 0x00003BDD},
+	{0x033, 0x00000004},
+	{0x03F, 0x00003BD7},
+	{0x033, 0x00000005},
+	{0x03F, 0x00003BD1},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00003BCB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00001BD9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BD1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00001BD3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00001BCD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000BD9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BD1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000BD3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000BCD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000859},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000857},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000859},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000851},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000819},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000084D},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000817},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000819},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000811},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x03F, 0x000039EE},
+	{0x033, 0x00000013},
+	{0x03F, 0x000039E8},
+	{0x033, 0x00000014},
+	{0x03F, 0x000039E2},
+	{0x033, 0x00000015},
+	{0x03F, 0x000039DC},
+	{0x033, 0x00000016},
+	{0x03F, 0x000039D6},
+	{0x033, 0x00000017},
+	{0x03F, 0x000039D0},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x03F, 0x000019D2},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x03F, 0x000009D2},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x03F, 0x000008D3},
+	{0x033, 0x0000001E},
+	{0x03F, 0x000008CD},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000023},
+	{0x03F, 0x00000807},
+	{0x033, 0x00000024},
+	{0x03F, 0x000039EE},
+	{0x033, 0x00000025},
+	{0x03F, 0x000039E8},
+	{0x033, 0x00000026},
+	{0x03F, 0x000039E2},
+	{0x033, 0x00000027},
+	{0x03F, 0x000039DC},
+	{0x033, 0x00000028},
+	{0x03F, 0x000039D6},
+	{0x033, 0x00000029},
+	{0x03F, 0x000039D0},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x03F, 0x000019D2},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x03F, 0x000009D2},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000030},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000035},
+	{0x03F, 0x00000807},
+	{0x033, 0x00000036},
+	{0x03F, 0x000039EE},
+	{0x033, 0x00000037},
+	{0x03F, 0x000039E8},
+	{0x033, 0x00000038},
+	{0x03F, 0x000039E2},
+	{0x033, 0x00000039},
+	{0x03F, 0x000039DC},
+	{0x033, 0x0000003A},
+	{0x03F, 0x000039D6},
+	{0x033, 0x0000003B},
+	{0x03F, 0x000039D0},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x03F, 0x000019D2},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D8},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x03F, 0x000009D2},
+	{0x033, 0x00000040},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CC},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000008D9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000041},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000042},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000043},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000044},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000045},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000046},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000047},
+	{0x03F, 0x00000807},
+	{0x033, 0x00000048},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000049},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000004F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000050},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000051},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000052},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000053},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000054},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000055},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000056},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000057},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000058},
+	{0x03F, 0x0000080D},
+	{0x033, 0x00000059},
+	{0x03F, 0x00000807},
+	{0x033, 0x0000005A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000005F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000060},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000061},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000062},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000063},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000064},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000065},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000066},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000067},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000068},
+	{0x03F, 0x0000084D},
+	{0x033, 0x00000069},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006A},
+	{0x03F, 0x0000080D},
+	{0x033, 0x0000006B},
+	{0x03F, 0x00000807},
+	{0x033, 0x0000006C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000006F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000070},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000071},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000072},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000073},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000074},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000075},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000076},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000077},
+	{0x03F, 0x000008D3},
+	{0x033, 0x00000078},
+	{0x03F, 0x000008CD},
+	{0x033, 0x00000079},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007A},
+	{0x03F, 0x0000084D},
+	{0x033, 0x0000007B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007C},
+	{0x03F, 0x0000080D},
+	{0x033, 0x0000007D},
+	{0x03F, 0x00000807},
+	{0x033, 0x0000007E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EE},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039EF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000007F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E8},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E9},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000080},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039E3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000081},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039DD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000082},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D6},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D7},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000083},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D0},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039D1},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000084},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CA},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000039CB},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000085},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000086},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CC},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000019CD},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000087},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D2},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000009D3},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000088},
+	{0x03F, 0x000009CD},
+	{0x033, 0x00000089},
+	{0x03F, 0x000008D3},
+	{0x033, 0x0000008A},
+	{0x03F, 0x000008CD},
+	{0x033, 0x0000008B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000008C7},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000853},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000008C},
+	{0x03F, 0x0000084D},
+	{0x033, 0x0000008D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000847},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x00000813},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000008E},
+	{0x03F, 0x0000080D},
+	{0x033, 0x0000008F},
+	{0x03F, 0x00000807},
+	{0x0EE, 0x00000000},
+	{0x0EF, 0x00080000},
+	{0x033, 0x00000007},
+	{0x03E, 0x00000001},
+	{0x03F, 0x00020F3C},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00080000},
+	{0x033, 0x0000000C},
+	{0x03E, 0x00000001},
+	{0x03F, 0x000305BC},
+	{0x0EF, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000001},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0EC, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0EC, 0x00000001},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x03C, 0x00000020},
+	{0x03D, 0x00000078},
+	{0x03E, 0x00080000},
+	{0x03F, 0x00001999},
+	{0x0EC, 0x00000000},
+	{0x02F, 0x0002260D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000001},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x0DE, 0x00000000},
+	{0xA0000000, 0x00000000},
+	{0x0DE, 0x00000001},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000002},
+	{0x033, 0x00000000},
+	{0x03F, 0x00000002},
+	{0x033, 0x00000001},
+	{0x03F, 0x00000002},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000400},
+	{0x033, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000001},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000002},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000003},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000004},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000005},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000006},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000007},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000008},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000009},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000000F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000010},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000011},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000012},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000013},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000014},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000015},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000016},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000017},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000018},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000019},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000001F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000020},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000021},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000022},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000023},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000024},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000025},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000026},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000027},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000017F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000013F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FB},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FA},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x0EF, 0x00000200},
+	{0x033, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000001},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000002},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000003},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000004},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000005},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000006},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000007},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000008},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000009},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000A},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000B},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000C},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000D},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000E},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000000F},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000010},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000011},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000012},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000013},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000014},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000015},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000016},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000017},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000018},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000019},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001A},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001B},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001C},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001D},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001E},
+	{0x03F, 0x000001FF},
+	{0x033, 0x0000001F},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000020},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000021},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000022},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000023},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000024},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000025},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000026},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000027},
+	{0x03F, 0x000001FF},
+	{0x033, 0x00000028},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000029},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x000001FF},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x000000FF},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000002F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000030},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000031},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000032},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000033},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000034},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000035},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000036},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000037},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000038},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x00000039},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003A},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003B},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003C},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003D},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003E},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x033, 0x0000003F},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003B},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xA0000000, 0x00000000},
+	{0x03F, 0x0000003F},
+	{0xB0000000, 0x00000000},
+	{0x0EF, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06E, 0x00067A7C},
+	{0xA0000000, 0x00000000},
+	{0x06E, 0x00077A7C},
+	{0xB0000000, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x06F, 0x00067A7C},
+	{0xA0000000, 0x00000000},
+	{0x06F, 0x00077A7C},
+	{0xB0000000, 0x00000000},
+	{0x06D, 0x00000C31},
+	{0x0EF, 0x00020000},
+	{0x033, 0x00000000},
+	{0x03F, 0x000005FF},
+	{0x0EF, 0x00000000},
+	{0x0A0, 0x00000043},
+	{0x005, 0x00000001},
+	{0x0EF, 0x00080000},
+	{0x033, 0x00000001},
+	{0x03E, 0x00000001},
+	{0x03F, 0x00022020},
+	{0x0EF, 0x00000000},
+	{0x80010000, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90010001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90020001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90030001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90250001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90260001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90320001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90330001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90340001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90350001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90360001, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90010002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90020002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90030002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90250002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90260002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0x90320002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90330002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90340002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90350002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0x90360002, 0x00000000}, {0x40000000, 0x00000000},
+	{0x087, 0x0000042F},
+	{0xA0000000, 0x00000000},
+	{0x087, 0x00000427},
+	{0xB0000000, 0x00000000},
+	{0x002, 0x00000000},
+	{0x067, 0x00000052},
+
+};
+
+static const struct rtw89_reg2_def rtw89_8852a_phy_nctl_regs[] = {
+	{0x8000, 0x00000008},
+	{0x8008, 0x00000000},
+	{0x8004, 0xf0862966},
+	{0x800c, 0x78000000},
+	{0x8010, 0x88015000},
+	{0x8014, 0x80010100},
+	{0x8018, 0x10010100},
+	{0x801c, 0xa210bc00},
+	{0x8020, 0x000403e0},
+	{0x8024, 0x00072160},
+	{0x8028, 0x00180e00},
+	{0x8030, 0x400000c0},
+	{0x8034, 0x56000800},
+	{0x8038, 0x00000009},
+	{0x803c, 0x00000008},
+	{0x8040, 0x00000046},
+	{0x8044, 0x0010001f},
+	{0x8048, 0xf0000003},
+	{0x804c, 0x62ac6162},
+	{0x8050, 0xf2acf162},
+	{0x8054, 0x62ac6162},
+	{0x8058, 0xf2acf162},
+	{0x805c, 0x150c0b02},
+	{0x8060, 0x150c0b02},
+	{0x8064, 0x2aa00047},
+	{0x8074, 0x80000000},
+	{0x807c, 0x000000ee},
+	{0x8088, 0x80000000},
+	{0x8098, 0x0000ff00},
+	{0x809c, 0x0000001f},
+	{0x80a0, 0x00010300},
+	{0x80b0, 0x00000000},
+	{0x80d0, 0x00000000},
+	{0x8114, 0x00000000},
+	{0x8120, 0x10010000},
+	{0x8124, 0x00000000},
+	{0x812c, 0x0000c000},
+	{0x8138, 0x40000002},
+	{0x813c, 0x40000002},
+	{0x8140, 0x00000000},
+	{0x8144, 0x0b040b03},
+	{0x8148, 0x0b040b04},
+	{0x814c, 0x0b040b03},
+	{0x8150, 0x00000000},
+	{0x8158, 0xffffffff},
+	{0x815c, 0xffffffff},
+	{0x8160, 0xffffffff},
+	{0x8164, 0xffffffff},
+	{0x8168, 0xffffffff},
+	{0x816c, 0x1fffffff},
+	{0x81ac, 0x003f1a00},
+	{0x81b0, 0x003f1a00},
+	{0x81bc, 0x005b5b5b},
+	{0x81c0, 0x005b5b5b},
+	{0x81b4, 0x00600060},
+	{0x81b8, 0x00600060},
+	{0x81cc, 0x00000000},
+	{0x81dc, 0x00000002},
+	{0x8214, 0x00000000},
+	{0x8220, 0x10010000},
+	{0x8224, 0x00000000},
+	{0x822c, 0x0000d000},
+	{0x8238, 0x40000002},
+	{0x823c, 0x40000002},
+	{0x8240, 0x00000000},
+	{0x8244, 0x0b040b03},
+	{0x8248, 0x0b040b03},
+	{0x824c, 0x0b030b03},
+	{0x8250, 0x00000000},
+	{0x8258, 0xffffffff},
+	{0x825c, 0xffffffff},
+	{0x8260, 0xffffffff},
+	{0x8264, 0xffffffff},
+	{0x8268, 0xffffffff},
+	{0x826c, 0x1fffffff},
+	{0x82ac, 0x003f1a00},
+	{0x82b0, 0x003f1a00},
+	{0x82bc, 0x005b5b5b},
+	{0x82c0, 0x005b5b5b},
+	{0x82b4, 0x00600060},
+	{0x82b8, 0x00600060},
+	{0x82cc, 0x00000000},
+	{0x82dc, 0x00000002},
+	{0x81d8, 0x00000001},
+	{0x82d8, 0x00000001},
+	{0x8d00, 0x00000000},
+	{0x8d04, 0x00000000},
+	{0x8d08, 0x00000000},
+	{0x8d0c, 0x00000000},
+	{0x8d10, 0x00000000},
+	{0x8d14, 0x00000000},
+	{0x8d18, 0x00000000},
+	{0x8d1c, 0x00000000},
+	{0x8d20, 0x00000000},
+	{0x8d24, 0x00000000},
+	{0x8d28, 0x00000000},
+	{0x8d2c, 0x00000000},
+	{0x8d30, 0x00000000},
+	{0x8d34, 0x00000000},
+	{0x8d38, 0x00000000},
+	{0x8d3c, 0x00000000},
+	{0x8d40, 0x00000000},
+	{0x8d44, 0x00000000},
+	{0x8d48, 0x00000000},
+	{0x8d4c, 0x00000000},
+	{0x8d50, 0x00000000},
+	{0x8d54, 0x00000000},
+	{0x8d58, 0x00000000},
+	{0x8d5c, 0x00000000},
+	{0x8d60, 0x00000000},
+	{0x8d64, 0x00000000},
+	{0x8d68, 0x00000000},
+	{0x8d6c, 0x00000000},
+	{0x8d70, 0x00000000},
+	{0x8d74, 0x00000000},
+	{0x8d78, 0x00000000},
+	{0x8d7c, 0x00000000},
+	{0x8d80, 0x00000000},
+	{0x8d84, 0x00000000},
+	{0x8d88, 0x00000000},
+	{0x8d8c, 0x00000000},
+	{0x8d90, 0x00000000},
+	{0x8d94, 0x00000000},
+	{0x8d98, 0x00000000},
+	{0x8d9c, 0x00000000},
+	{0x8da0, 0x00000000},
+	{0x8da4, 0x00000000},
+	{0x8da8, 0x00000000},
+	{0x8dac, 0x00000000},
+	{0x8db0, 0x00000000},
+	{0x8db4, 0x00000000},
+	{0x8db8, 0x00000000},
+	{0x8dbc, 0x00000000},
+	{0x8dc0, 0x00000000},
+	{0x8dc4, 0x00000000},
+	{0x8dc8, 0x00000000},
+	{0x8dcc, 0x00000000},
+	{0x8dd0, 0x00000000},
+	{0x8dd4, 0x00000000},
+	{0x8dd8, 0x00000000},
+	{0x8ddc, 0x00000000},
+	{0x8de0, 0x00000000},
+	{0x8de4, 0x00000000},
+	{0x8de8, 0x00000000},
+	{0x8dec, 0x00000000},
+	{0x8df0, 0x00000000},
+	{0x8df4, 0x00000000},
+	{0x8df8, 0x00000000},
+	{0x8dfc, 0x00000000},
+	{0x8e00, 0x00000000},
+	{0x8e04, 0x00000000},
+	{0x8e08, 0x00000000},
+	{0x8e0c, 0x00000000},
+	{0x8e10, 0x00000000},
+	{0x8e14, 0x00000000},
+	{0x8e18, 0x00000000},
+	{0x8e1c, 0x00000000},
+	{0x8e20, 0x00000000},
+	{0x8e24, 0x00000000},
+	{0x8e28, 0x00000000},
+	{0x8e2c, 0x00000000},
+	{0x8e30, 0x00000000},
+	{0x8e34, 0x00000000},
+	{0x8e38, 0x00000000},
+	{0x8e3c, 0x00000000},
+	{0x8e40, 0x00000000},
+	{0x8e44, 0x00000000},
+	{0x8e48, 0x00000000},
+	{0x8e4c, 0x00000000},
+	{0x8e50, 0x00000000},
+	{0x8e54, 0x00000000},
+	{0x8e58, 0x00000000},
+	{0x8e5c, 0x00000000},
+	{0x8e60, 0x00000000},
+	{0x8e64, 0x00000000},
+	{0x8e68, 0x00000000},
+	{0x8e6c, 0x00000000},
+	{0x8e70, 0x00000000},
+	{0x8e74, 0x00000000},
+	{0x8e78, 0x00000000},
+	{0x8e7c, 0x00000000},
+	{0x8e80, 0x00000000},
+	{0x8e84, 0x00000000},
+	{0x8e88, 0x00000000},
+	{0x8e8c, 0x00000000},
+	{0x8e90, 0x00000000},
+	{0x8e94, 0x00000000},
+	{0x8e98, 0x00000000},
+	{0x8e9c, 0x00000000},
+	{0x8ea0, 0x00000000},
+	{0x8ea4, 0x00000000},
+	{0x8ea8, 0x00000000},
+	{0x8eac, 0x00000000},
+	{0x8eb0, 0x00000000},
+	{0x8eb4, 0x00000000},
+	{0x8eb8, 0x00000000},
+	{0x8ebc, 0x00000000},
+	{0x8ec0, 0x00000000},
+	{0x8ec4, 0x00000000},
+	{0x8ec8, 0x00000000},
+	{0x8ecc, 0x00000000},
+	{0x8ed0, 0x00000000},
+	{0x8ed4, 0x00000000},
+	{0x8ed8, 0x00000000},
+	{0x8edc, 0x00000000},
+	{0x8ee0, 0x00000000},
+	{0x8ee4, 0x00000000},
+	{0x8ee8, 0x00000000},
+	{0x8eec, 0x00000000},
+	{0x8ef0, 0x00000000},
+	{0x8ef4, 0x00000000},
+	{0x8ef8, 0x00000000},
+	{0x8efc, 0x00000000},
+	{0x8f00, 0x00000000},
+	{0x8f04, 0x00000000},
+	{0x8f08, 0x00000000},
+	{0x8f0c, 0x00000000},
+	{0x8f10, 0x00000000},
+	{0x8f14, 0x00000000},
+	{0x8f18, 0x00000000},
+	{0x8f1c, 0x00000000},
+	{0x8f20, 0x00000000},
+	{0x8f24, 0x00000000},
+	{0x8f28, 0x00000000},
+	{0x8f2c, 0x00000000},
+	{0x8f30, 0x00000000},
+	{0x8f34, 0x00000000},
+	{0x8f38, 0x00000000},
+	{0x8f3c, 0x00000000},
+	{0x8f40, 0x00000000},
+	{0x8f44, 0x00000000},
+	{0x8f48, 0x00000000},
+	{0x8f4c, 0x00000000},
+	{0x8f50, 0x00000000},
+	{0x8f54, 0x00000000},
+	{0x8f58, 0x00000000},
+	{0x8f5c, 0x00000000},
+	{0x8f60, 0x00000000},
+	{0x8f64, 0x00000000},
+	{0x8f68, 0x00000000},
+	{0x8f6c, 0x00000000},
+	{0x8f70, 0x00000000},
+	{0x8f74, 0x00000000},
+	{0x8f78, 0x00000000},
+	{0x8f7c, 0x00000000},
+	{0x8f80, 0x00000000},
+	{0x8f84, 0x00000000},
+	{0x8f88, 0x00000000},
+	{0x8f8c, 0x00000000},
+	{0x8f90, 0x00000000},
+	{0x8f94, 0x00000000},
+	{0x8f98, 0x00000000},
+	{0x8f9c, 0x00000000},
+	{0x8fa0, 0x00000000},
+	{0x8fa4, 0x00000000},
+	{0x8fa8, 0x00000000},
+	{0x8fac, 0x00000000},
+	{0x8fb0, 0x00000000},
+	{0x8fb4, 0x00000000},
+	{0x8fb8, 0x00000000},
+	{0x8fbc, 0x00000000},
+	{0x8fc0, 0x00000000},
+	{0x8fc4, 0x00000000},
+	{0x8fc8, 0x00000000},
+	{0x8fcc, 0x00000000},
+	{0x8fd0, 0x00000000},
+	{0x8fd4, 0x00000000},
+	{0x8fd8, 0x00000000},
+	{0x8fdc, 0x00000000},
+	{0x8fe0, 0x00000000},
+	{0x8fe4, 0x00000000},
+	{0x8fe8, 0x00000000},
+	{0x8fec, 0x00000000},
+	{0x8ff0, 0x00000000},
+	{0x8ff4, 0x00000000},
+	{0x8ff8, 0x00000000},
+	{0x8ffc, 0x00000000},
+	{0x9000, 0x00000000},
+	{0x9004, 0x00000000},
+	{0x9008, 0x00000000},
+	{0x900c, 0x00000000},
+	{0x9010, 0x00000000},
+	{0x9014, 0x00000000},
+	{0x9018, 0x00000000},
+	{0x901c, 0x00000000},
+	{0x9020, 0x00000000},
+	{0x9024, 0x00000000},
+	{0x9028, 0x00000000},
+	{0x902c, 0x00000000},
+	{0x9030, 0x00000000},
+	{0x9034, 0x00000000},
+	{0x9038, 0x00000000},
+	{0x903c, 0x00000000},
+	{0x9040, 0x00000000},
+	{0x9044, 0x00000000},
+	{0x9048, 0x00000000},
+	{0x904c, 0x00000000},
+	{0x9050, 0x00000000},
+	{0x9054, 0x00000000},
+	{0x9058, 0x00000000},
+	{0x905c, 0x00000000},
+	{0x9060, 0x00000000},
+	{0x9064, 0x00000000},
+	{0x9068, 0x00000000},
+	{0x906c, 0x00000000},
+	{0x9070, 0x00000000},
+	{0x9074, 0x00000000},
+	{0x9078, 0x00000000},
+	{0x907c, 0x00000000},
+	{0x9080, 0x00000000},
+	{0x9084, 0x00000000},
+	{0x9088, 0x00000000},
+	{0x908c, 0x00000000},
+	{0x9090, 0x00000000},
+	{0x9094, 0x00000000},
+	{0x9098, 0x00000000},
+	{0x909c, 0x00000000},
+	{0x90a0, 0x00000000},
+	{0x90a4, 0x00000000},
+	{0x90a8, 0x00000000},
+	{0x90ac, 0x00000000},
+	{0x90b0, 0x00000000},
+	{0x90b4, 0x00000000},
+	{0x90b8, 0x00000000},
+	{0x90bc, 0x00000000},
+	{0x9100, 0x00000000},
+	{0x9104, 0x00000000},
+	{0x9108, 0x00000000},
+	{0x910c, 0x00000000},
+	{0x9110, 0x00000000},
+	{0x9114, 0x00000000},
+	{0x9118, 0x00000000},
+	{0x911c, 0x00000000},
+	{0x9120, 0x00000000},
+	{0x9124, 0x00000000},
+	{0x9128, 0x00000000},
+	{0x912c, 0x00000000},
+	{0x9130, 0x00000000},
+	{0x9134, 0x00000000},
+	{0x9138, 0x00000000},
+	{0x913c, 0x00000000},
+	{0x9140, 0x00000000},
+	{0x9144, 0x00000000},
+	{0x9148, 0x00000000},
+	{0x914c, 0x00000000},
+	{0x9150, 0x00000000},
+	{0x9154, 0x00000000},
+	{0x9158, 0x00000000},
+	{0x915c, 0x00000000},
+	{0x9160, 0x00000000},
+	{0x9164, 0x00000000},
+	{0x9168, 0x00000000},
+	{0x916c, 0x00000000},
+	{0x9170, 0x00000000},
+	{0x9174, 0x00000000},
+	{0x9178, 0x00000000},
+	{0x917c, 0x00000000},
+	{0x9180, 0x00000000},
+	{0x9184, 0x00000000},
+	{0x9188, 0x00000000},
+	{0x918c, 0x00000000},
+	{0x9190, 0x00000000},
+	{0x9194, 0x00000000},
+	{0x9198, 0x00000000},
+	{0x919c, 0x00000000},
+	{0x91a0, 0x00000000},
+	{0x91a4, 0x00000000},
+	{0x91a8, 0x00000000},
+	{0x91ac, 0x00000000},
+	{0x91b0, 0x00000000},
+	{0x91b4, 0x00000000},
+	{0x91b8, 0x00000000},
+	{0x91bc, 0x00000000},
+	{0x91c0, 0x00000000},
+	{0x91c4, 0x00000000},
+	{0x91c8, 0x00000000},
+	{0x91cc, 0x00000000},
+	{0x91d0, 0x00000000},
+	{0x91d4, 0x00000000},
+	{0x91d8, 0x00000000},
+	{0x91dc, 0x00000000},
+	{0x91e0, 0x00000000},
+	{0x91e4, 0x00000000},
+	{0x91e8, 0x00000000},
+	{0x91ec, 0x00000000},
+	{0x91f0, 0x00000000},
+	{0x91f4, 0x00000000},
+	{0x91f8, 0x00000000},
+	{0x91fc, 0x00000000},
+	{0x9200, 0x00000000},
+	{0x9204, 0x00000000},
+	{0x9208, 0x00000000},
+	{0x920c, 0x00000000},
+	{0x9210, 0x00000000},
+	{0x9214, 0x00000000},
+	{0x9218, 0x00000000},
+	{0x921c, 0x00000000},
+	{0x9220, 0x00000000},
+	{0x9224, 0x00000000},
+	{0x9228, 0x00000000},
+	{0x922c, 0x00000000},
+	{0x9230, 0x00000000},
+	{0x9234, 0x00000000},
+	{0x9238, 0x00000000},
+	{0x923c, 0x00000000},
+	{0x9240, 0x00000000},
+	{0x9244, 0x00000000},
+	{0x9248, 0x00000000},
+	{0x924c, 0x00000000},
+	{0x9250, 0x00000000},
+	{0x9254, 0x00000000},
+	{0x9258, 0x00000000},
+	{0x925c, 0x00000000},
+	{0x9260, 0x00000000},
+	{0x9264, 0x00000000},
+	{0x9268, 0x00000000},
+	{0x926c, 0x00000000},
+	{0x9270, 0x00000000},
+	{0x9274, 0x00000000},
+	{0x9278, 0x00000000},
+	{0x927c, 0x00000000},
+	{0x9280, 0x00000000},
+	{0x9284, 0x00000000},
+	{0x9288, 0x00000000},
+	{0x928c, 0x00000000},
+	{0x9290, 0x00000000},
+	{0x9294, 0x00000000},
+	{0x9298, 0x00000000},
+	{0x929c, 0x00000000},
+	{0x92a0, 0x00000000},
+	{0x92a4, 0x00000000},
+	{0x92a8, 0x00000000},
+	{0x92ac, 0x00000000},
+	{0x92b0, 0x00000000},
+	{0x92b4, 0x00000000},
+	{0x92b8, 0x00000000},
+	{0x92bc, 0x00000000},
+	{0x92c0, 0x00000000},
+	{0x92c4, 0x00000000},
+	{0x92c8, 0x00000000},
+	{0x92cc, 0x00000000},
+	{0x92d0, 0x00000000},
+	{0x92d4, 0x00000000},
+	{0x92d8, 0x00000000},
+	{0x92dc, 0x00000000},
+	{0x92e0, 0x00000000},
+	{0x92e4, 0x00000000},
+	{0x92e8, 0x00000000},
+	{0x92ec, 0x00000000},
+	{0x92f0, 0x00000000},
+	{0x92f4, 0x00000000},
+	{0x92f8, 0x00000000},
+	{0x92fc, 0x00000000},
+	{0x9300, 0x00000000},
+	{0x9304, 0x00000000},
+	{0x9308, 0x00000000},
+	{0x930c, 0x00000000},
+	{0x9310, 0x00000000},
+	{0x9314, 0x00000000},
+	{0x9318, 0x00000000},
+	{0x931c, 0x00000000},
+	{0x9320, 0x00000000},
+	{0x9324, 0x00000000},
+	{0x9328, 0x00000000},
+	{0x932c, 0x00000000},
+	{0x9330, 0x00000000},
+	{0x9334, 0x00000000},
+	{0x9338, 0x00000000},
+	{0x933c, 0x00000000},
+	{0x9340, 0x00000000},
+	{0x9344, 0x00000000},
+	{0x9348, 0x00000000},
+	{0x934c, 0x00000000},
+	{0x9350, 0x00000000},
+	{0x9354, 0x00000000},
+	{0x9358, 0x00000000},
+	{0x935c, 0x00000000},
+	{0x9360, 0x00000000},
+	{0x9364, 0x00000000},
+	{0x9368, 0x00000000},
+	{0x936c, 0x00000000},
+	{0x9370, 0x00000000},
+	{0x9374, 0x00000000},
+	{0x9378, 0x00000000},
+	{0x937c, 0x00000000},
+	{0x9380, 0x00000000},
+	{0x9384, 0x00000000},
+	{0x9388, 0x00000000},
+	{0x938c, 0x00000000},
+	{0x9390, 0x00000000},
+	{0x9394, 0x00000000},
+	{0x9398, 0x00000000},
+	{0x939c, 0x00000000},
+	{0x93a0, 0x00000000},
+	{0x93a4, 0x00000000},
+	{0x93a8, 0x00000000},
+	{0x93ac, 0x00000000},
+	{0x93b0, 0x00000000},
+	{0x93b4, 0x00000000},
+	{0x93b8, 0x00000000},
+	{0x93bc, 0x00000000},
+	{0x93c0, 0x00000000},
+	{0x93c4, 0x00000000},
+	{0x93c8, 0x00000000},
+	{0x93cc, 0x00000000},
+	{0x93d0, 0x00000000},
+	{0x93d4, 0x00000000},
+	{0x93d8, 0x00000000},
+	{0x93dc, 0x00000000},
+	{0x93e0, 0x00000000},
+	{0x93e4, 0x00000000},
+	{0x93e8, 0x00000000},
+	{0x93ec, 0x00000000},
+	{0x93f0, 0x00000000},
+	{0x93f4, 0x00000000},
+	{0x93f8, 0x00000000},
+	{0x93fc, 0x00000000},
+	{0x9400, 0x00000000},
+	{0x9404, 0x00000000},
+	{0x9408, 0x00000000},
+	{0x940c, 0x00000000},
+	{0x9410, 0x00000000},
+	{0x9414, 0x00000000},
+	{0x9418, 0x00000000},
+	{0x941c, 0x00000000},
+	{0x9420, 0x00000000},
+	{0x9424, 0x00000000},
+	{0x9428, 0x00000000},
+	{0x942c, 0x00000000},
+	{0x9430, 0x00000000},
+	{0x9434, 0x00000000},
+	{0x9438, 0x00000000},
+	{0x943c, 0x00000000},
+	{0x9440, 0x00000000},
+	{0x9444, 0x00000000},
+	{0x9448, 0x00000000},
+	{0x944c, 0x00000000},
+	{0x9450, 0x00000000},
+	{0x9454, 0x00000000},
+	{0x9458, 0x00000000},
+	{0x945c, 0x00000000},
+	{0x9460, 0x00000000},
+	{0x9464, 0x00000000},
+	{0x9468, 0x00000000},
+	{0x946c, 0x00000000},
+	{0x9470, 0x00000000},
+	{0x9474, 0x00000000},
+	{0x9478, 0x00000000},
+	{0x947c, 0x00000000},
+	{0x9480, 0x00000000},
+	{0x9484, 0x00000000},
+	{0x9488, 0x00000000},
+	{0x948c, 0x00000000},
+	{0x9490, 0x00000000},
+	{0x9494, 0x00000000},
+	{0x9498, 0x00000000},
+	{0x949c, 0x00000000},
+	{0x94a0, 0x00000000},
+	{0x94a4, 0x00000000},
+	{0x94a8, 0x00000000},
+	{0x94ac, 0x00000000},
+	{0x94b0, 0x00000000},
+	{0x94b4, 0x00000000},
+	{0x94b8, 0x00000000},
+	{0x94bc, 0x00000000},
+	{0x81d8, 0x00000000},
+	{0x82d8, 0x00000000},
+	{0x9f04, 0x2b251f19},
+	{0x9f08, 0x433d3731},
+	{0x9f0c, 0x5b554f49},
+	{0x9f10, 0x736d6761},
+	{0x9f14, 0x7f7f7f79},
+	{0x9f18, 0x120f7f7f},
+	{0x9f1c, 0x1e1b1815},
+	{0x9f20, 0x2a272421},
+	{0x9f24, 0x3633302d},
+	{0x9f28, 0x3f3f3c39},
+	{0x9f2c, 0x3f3f3f3f},
+	{0x8088, 0x00000110},
+	{0x8000, 0x00000008},
+	{0x8080, 0x00000005},
+	{0x8500, 0x00060009},
+	{0x8504, 0x000418b0},
+	{0x8508, 0x00089c00},
+	{0x850c, 0x43000004},
+	{0x8510, 0x4b044a00},
+	{0x8514, 0x40098603},
+	{0x8518, 0x4b05e01f},
+	{0x851c, 0x400b8703},
+	{0x8520, 0x4b00e01f},
+	{0x8524, 0x43800004},
+	{0x8528, 0x4c000007},
+	{0x852c, 0x43000004},
+	{0x8530, 0x57007430},
+	{0x8534, 0x73000006},
+	{0x8538, 0x50550004},
+	{0x853c, 0xb4163000},
+	{0x8540, 0xe37ea510},
+	{0x8544, 0xf117f017},
+	{0x8548, 0xf317f217},
+	{0x854c, 0xf517f417},
+	{0x8550, 0xf717f617},
+	{0x8554, 0xf917f817},
+	{0x8558, 0xfb17fa17},
+	{0x855c, 0xfd17fc17},
+	{0x8560, 0xf117f017},
+	{0x8564, 0xf317f217},
+	{0x8568, 0xa503f417},
+	{0x856c, 0xf116f016},
+	{0x8570, 0x304e0001},
+	{0x8574, 0x30873053},
+	{0x8578, 0x30ab30a8},
+	{0x857c, 0x30b330ae},
+	{0x8580, 0x30ba30b6},
+	{0x8584, 0x30d430c7},
+	{0x8588, 0x310d3100},
+	{0x858c, 0x31ed3112},
+	{0x8590, 0x320a31f1},
+	{0x8594, 0x3243320b},
+	{0x8598, 0x31e631b1},
+	{0x859c, 0x5b00e283},
+	{0x85a0, 0xe2d15500},
+	{0x85a4, 0xe2830001},
+	{0x85a8, 0x5b10e2e3},
+	{0x85ac, 0x20987410},
+	{0x85b0, 0xe3750200},
+	{0x85b4, 0x00002080},
+	{0x85b8, 0x23f0e375},
+	{0x85bc, 0xe3750001},
+	{0x85c0, 0x000023f0},
+	{0x85c4, 0x5507e375},
+	{0x85c8, 0xe2d5e2d5},
+	{0x85cc, 0x20887410},
+	{0x85d0, 0xe3750200},
+	{0x85d4, 0x000123f0},
+	{0x85d8, 0x23f0e375},
+	{0x85dc, 0xe3750000},
+	{0x85e0, 0xe2d55517},
+	{0x85e4, 0x4e004f02},
+	{0x85e8, 0x52015302},
+	{0x85ec, 0x7508e2d9},
+	{0x85f0, 0x74207900},
+	{0x85f4, 0x57005710},
+	{0x85f8, 0x75fbe375},
+	{0x85fc, 0x23f07410},
+	{0x8600, 0xe3750001},
+	{0x8604, 0x000023f0},
+	{0x8608, 0x7430e375},
+	{0x860c, 0x5b100001},
+	{0x8610, 0x20907410},
+	{0x8614, 0xe3750000},
+	{0x8618, 0x000123f0},
+	{0x861c, 0x23f0e375},
+	{0x8620, 0xe3750000},
+	{0x8624, 0xe2d55507},
+	{0x8628, 0x7410e2d5},
+	{0x862c, 0x02002098},
+	{0x8630, 0x23f0e375},
+	{0x8634, 0xe3750001},
+	{0x8638, 0x000023f0},
+	{0x863c, 0x5517e375},
+	{0x8640, 0x4f02e2d5},
+	{0x8644, 0x53024e00},
+	{0x8648, 0xe2d95201},
+	{0x864c, 0x30787509},
+	{0x8650, 0xe2e3e283},
+	{0x8654, 0xe27b0001},
+	{0x8658, 0x0001e2e3},
+	{0x865c, 0x5b30e28f},
+	{0x8660, 0xe2d15500},
+	{0x8664, 0xe28f0001},
+	{0x8668, 0x0001e312},
+	{0x866c, 0x4380e287},
+	{0x8670, 0x0001e312},
+	{0x8674, 0x30e2e283},
+	{0x8678, 0xe3600023},
+	{0x867c, 0x54ed0002},
+	{0x8680, 0x00230baa},
+	{0x8684, 0x0002e360},
+	{0x8688, 0xe27be330},
+	{0x868c, 0xe2830001},
+	{0x8690, 0x002230dd},
+	{0x8694, 0x0002e360},
+	{0x8698, 0x0baa54ec},
+	{0x869c, 0xe3600022},
+	{0x86a0, 0xe3300002},
+	{0x86a4, 0x0001e27b},
+	{0x86a8, 0x0baae283},
+	{0x86ac, 0x6d0f6c67},
+	{0x86b0, 0xe360e2e3},
+	{0x86b4, 0xe2e36c8b},
+	{0x86b8, 0x0bace360},
+	{0x86bc, 0x6d0f6cb3},
+	{0x86c0, 0xe360e2e3},
+	{0x86c4, 0x6cdb0bad},
+	{0x86c8, 0xe2e36d0f},
+	{0x86cc, 0x6cf7e360},
+	{0x86d0, 0xe2e36d0f},
+	{0x86d4, 0x6c09e360},
+	{0x86d8, 0xe2e36d00},
+	{0x86dc, 0x6c25e360},
+	{0x86e0, 0xe360e2e3},
+	{0x86e4, 0x6c4df8ca},
+	{0x86e8, 0xe360e2e3},
+	{0x86ec, 0x6c75f9d3},
+	{0x86f0, 0xe360e2e3},
+	{0x86f4, 0xe2e36c99},
+	{0x86f8, 0xe330e360},
+	{0x86fc, 0x0001e27b},
+	{0x8700, 0x314de28f},
+	{0x8704, 0xe3650022},
+	{0x8708, 0x54ec0002},
+	{0x870c, 0x00220baa},
+	{0x8710, 0x0002e365},
+	{0x8714, 0xe287e330},
+	{0x8718, 0xe28f0001},
+	{0x871c, 0xe3303139},
+	{0x8720, 0x0001e287},
+	{0x8724, 0x0ba6e28f},
+	{0x8728, 0x21e07410},
+	{0x872c, 0x21e80009},
+	{0x8730, 0x6e670009},
+	{0x8734, 0xe32b6f0f},
+	{0x8738, 0xe365e312},
+	{0x873c, 0x21e07410},
+	{0x8740, 0x21e8000a},
+	{0x8744, 0x6e77000a},
+	{0x8748, 0xe312e32b},
+	{0x874c, 0x7410e365},
+	{0x8750, 0x000b21e0},
+	{0x8754, 0x000b21e8},
+	{0x8758, 0xe32b6e8b},
+	{0x875c, 0xe365e312},
+	{0x8760, 0x21e07410},
+	{0x8764, 0x21e8000c},
+	{0x8768, 0x6e9f000c},
+	{0x876c, 0xe312e32b},
+	{0x8770, 0x0baae365},
+	{0x8774, 0x21e07410},
+	{0x8778, 0x21e8000d},
+	{0x877c, 0x6eb3000d},
+	{0x8780, 0xe32b6f0f},
+	{0x8784, 0xe365e312},
+	{0x8788, 0x21e07410},
+	{0x878c, 0x21e8000e},
+	{0x8790, 0x6ec7000e},
+	{0x8794, 0xe312e32b},
+	{0x8798, 0x0bace365},
+	{0x879c, 0x21e07410},
+	{0x87a0, 0x21e8000f},
+	{0x87a4, 0x6edb000f},
+	{0x87a8, 0xe32b6f0f},
+	{0x87ac, 0xe365e312},
+	{0x87b0, 0x21e07410},
+	{0x87b4, 0x21e80010},
+	{0x87b8, 0x6eef0010},
+	{0x87bc, 0xe312e32b},
+	{0x87c0, 0xe365e365},
+	{0x87c4, 0x21e07410},
+	{0x87c8, 0x21e80013},
+	{0x87cc, 0x6e110013},
+	{0x87d0, 0xe32b6f00},
+	{0x87d4, 0xe365e312},
+	{0x87d8, 0x7410e365},
+	{0x87dc, 0x001421e0},
+	{0x87e0, 0x001421e8},
+	{0x87e4, 0xe32b6e25},
+	{0x87e8, 0xe365e312},
+	{0x87ec, 0x7410fb8c},
+	{0x87f0, 0x001521e0},
+	{0x87f4, 0x001521e8},
+	{0x87f8, 0xe32b6e39},
+	{0x87fc, 0xe365e312},
+	{0x8800, 0x21e07410},
+	{0x8804, 0x21e80016},
+	{0x8808, 0x6e4d0016},
+	{0x880c, 0xe312e32b},
+	{0x8810, 0xfc86e365},
+	{0x8814, 0x21e07410},
+	{0x8818, 0x21e80017},
+	{0x881c, 0x6e610017},
+	{0x8820, 0xe312e32b},
+	{0x8824, 0x7410e365},
+	{0x8828, 0x001821e0},
+	{0x882c, 0x001821e8},
+	{0x8830, 0xe32b6e75},
+	{0x8834, 0xe365e312},
+	{0x8838, 0x21e07410},
+	{0x883c, 0x21e80019},
+	{0x8840, 0x6e890019},
+	{0x8844, 0xe312e32b},
+	{0x8848, 0x7410e365},
+	{0x884c, 0x001a21e0},
+	{0x8850, 0x001a21e8},
+	{0x8854, 0xe32b6e99},
+	{0x8858, 0xe365e312},
+	{0x885c, 0xe287e330},
+	{0x8860, 0x00040001},
+	{0x8864, 0x0007775c},
+	{0x8868, 0x62006220},
+	{0x886c, 0x55010004},
+	{0x8870, 0xe2d15b00},
+	{0x8874, 0x66055b40},
+	{0x8878, 0x62000007},
+	{0x887c, 0xe3506300},
+	{0x8880, 0xe2d10004},
+	{0x8884, 0x0a010900},
+	{0x8888, 0x0d000b40},
+	{0x888c, 0x00320e01},
+	{0x8890, 0x95060004},
+	{0x8894, 0x00074380},
+	{0x8898, 0x00044d01},
+	{0x889c, 0x00074300},
+	{0x88a0, 0x05a30562},
+	{0x88a4, 0xe3509617},
+	{0x88a8, 0xe2d10004},
+	{0x88ac, 0x06a20007},
+	{0x88b0, 0xe35007a3},
+	{0x88b4, 0xe2d10004},
+	{0x88b8, 0x0002e340},
+	{0x88bc, 0x4380e348},
+	{0x88c0, 0x4d000007},
+	{0x88c4, 0x43000004},
+	{0x88c8, 0x00017900},
+	{0x88cc, 0x775e0004},
+	{0x88d0, 0x000731b3},
+	{0x88d4, 0x07a306a2},
+	{0x88d8, 0xe29331dd},
+	{0x88dc, 0x73000005},
+	{0x88e0, 0xe2930001},
+	{0x88e4, 0x5d000006},
+	{0x88e8, 0x42f70004},
+	{0x88ec, 0x6c000005},
+	{0x88f0, 0x42000004},
+	{0x88f4, 0x0004e2ab},
+	{0x88f8, 0x00074380},
+	{0x88fc, 0x4a004e00},
+	{0x8900, 0x00064c00},
+	{0x8904, 0x60007f00},
+	{0x8908, 0x00046f00},
+	{0x890c, 0x00054300},
+	{0x8910, 0x00017300},
+	{0x8914, 0xe2930001},
+	{0x8918, 0x5d010006},
+	{0x891c, 0x61006002},
+	{0x8920, 0x00055601},
+	{0x8924, 0xe2ab7710},
+	{0x8928, 0x73000005},
+	{0x892c, 0x43800004},
+	{0x8930, 0x5e010007},
+	{0x8934, 0x4d205e00},
+	{0x8938, 0x4a084e20},
+	{0x893c, 0x4c3f4960},
+	{0x8940, 0x00064301},
+	{0x8944, 0x63807f01},
+	{0x8948, 0x00046010},
+	{0x894c, 0x00064300},
+	{0x8950, 0x00077402},
+	{0x8954, 0x40004001},
+	{0x8958, 0x0006ab00},
+	{0x895c, 0x00077404},
+	{0x8960, 0x40004001},
+	{0x8964, 0x0004ab00},
+	{0x8968, 0x00074380},
+	{0x896c, 0x4e004d00},
+	{0x8970, 0x4c004a00},
+	{0x8974, 0x00064300},
+	{0x8978, 0x63007f00},
+	{0x897c, 0x6f006000},
+	{0x8980, 0x43000004},
+	{0x8984, 0x00040001},
+	{0x8988, 0x42bf4380},
+	{0x898c, 0x48400007},
+	{0x8990, 0x42ef0004},
+	{0x8994, 0x4d100007},
+	{0x8998, 0x42000004},
+	{0x899c, 0x5f800006},
+	{0x89a0, 0x5a010007},
+	{0x89a4, 0x00044a08},
+	{0x89a8, 0x00054300},
+	{0x89ac, 0x73807381},
+	{0x89b0, 0x003f9300},
+	{0x89b4, 0x00000000},
+	{0x89b8, 0x00000000},
+	{0x89bc, 0x00020000},
+	{0x89c0, 0x5f800006},
+	{0x89c4, 0x99005f00},
+	{0x89c8, 0x43800004},
+	{0x89cc, 0x00074280},
+	{0x89d0, 0x00044800},
+	{0x89d4, 0x000742ef},
+	{0x89d8, 0x00044d00},
+	{0x89dc, 0x00064200},
+	{0x89e0, 0x60005f00},
+	{0x89e4, 0x5a000007},
+	{0x89e8, 0x48004a00},
+	{0x89ec, 0x43000004},
+	{0x89f0, 0x73000005},
+	{0x89f4, 0x43800001},
+	{0x89f8, 0x78006505},
+	{0x89fc, 0x7a007900},
+	{0x8a00, 0x43007b00},
+	{0x8a04, 0x43800001},
+	{0x8a08, 0x43006500},
+	{0x8a0c, 0x43800001},
+	{0x8a10, 0x7c006405},
+	{0x8a14, 0x7e007d00},
+	{0x8a18, 0x43007f00},
+	{0x8a1c, 0x43800001},
+	{0x8a20, 0x43006400},
+	{0x8a24, 0x00060001},
+	{0x8a28, 0x55025601},
+	{0x8a2c, 0x00055400},
+	{0x8a30, 0x7e127f00},
+	{0x8a34, 0x76007710},
+	{0x8a38, 0x74007500},
+	{0x8a3c, 0x42700004},
+	{0x8a40, 0x73810005},
+	{0x8a44, 0x00047380},
+	{0x8a48, 0x93004200},
+	{0x8a4c, 0x77000005},
+	{0x8a50, 0x56000006},
+	{0x8a54, 0x00060001},
+	{0x8a58, 0x5f005f80},
+	{0x8a5c, 0x00059900},
+	{0x8a60, 0x00067300},
+	{0x8a64, 0x63006380},
+	{0x8a68, 0x00019800},
+	{0x8a6c, 0x7b484380},
+	{0x8a70, 0x79007a90},
+	{0x8a74, 0x43007802},
+	{0x8a78, 0x32cd5503},
+	{0x8a7c, 0x7b384380},
+	{0x8a80, 0x79007a80},
+	{0x8a84, 0x43007802},
+	{0x8a88, 0x32cd5513},
+	{0x8a8c, 0x7b404380},
+	{0x8a90, 0x79007a00},
+	{0x8a94, 0x43007802},
+	{0x8a98, 0x74315523},
+	{0x8a9c, 0x8e007430},
+	{0x8aa0, 0x74010001},
+	{0x8aa4, 0x8e007400},
+	{0x8aa8, 0x74310001},
+	{0x8aac, 0x8e007430},
+	{0x8ab0, 0x57020001},
+	{0x8ab4, 0x97005700},
+	{0x8ab8, 0x42ef0001},
+	{0x8abc, 0x56005610},
+	{0x8ac0, 0x8c004200},
+	{0x8ac4, 0x4f780001},
+	{0x8ac8, 0x53884e00},
+	{0x8acc, 0x5b205201},
+	{0x8ad0, 0x5480e2f2},
+	{0x8ad4, 0x54815400},
+	{0x8ad8, 0x54825400},
+	{0x8adc, 0xe2fd5400},
+	{0x8ae0, 0x3012bf1d},
+	{0x8ae4, 0xe2bee2b6},
+	{0x8ae8, 0xe2d9e2c6},
+	{0x8aec, 0x5523e359},
+	{0x8af0, 0x5525e2cd},
+	{0x8af4, 0xe359e2d9},
+	{0x8af8, 0x54bf0001},
+	{0x8afc, 0x54a354c0},
+	{0x8b00, 0x54a454c1},
+	{0x8b04, 0xbf074c18},
+	{0x8b08, 0x54a454c2},
+	{0x8b0c, 0x54c1bf04},
+	{0x8b10, 0xbf0154a3},
+	{0x8b14, 0x54dfe36a},
+	{0x8b18, 0x54bf0001},
+	{0x8b1c, 0x050a54e5},
+	{0x8b20, 0x000154df},
+	{0x8b24, 0x43807b80},
+	{0x8b28, 0x7e007f40},
+	{0x8b2c, 0x7c027d00},
+	{0x8b30, 0x5b404300},
+	{0x8b34, 0x5c015501},
+	{0x8b38, 0x5480e2dd},
+	{0x8b3c, 0x54815400},
+	{0x8b40, 0x54825400},
+	{0x8b44, 0x7b005400},
+	{0x8b48, 0xbfe8e2fd},
+	{0x8b4c, 0x56103012},
+	{0x8b50, 0x8c005600},
+	{0x8b54, 0xe36d0001},
+	{0x8b58, 0xe36de36d},
+	{0x8b5c, 0x0001e36d},
+	{0x8b60, 0x57005704},
+	{0x8b64, 0x57089700},
+	{0x8b68, 0x97005700},
+	{0x8b6c, 0x57805781},
+	{0x8b70, 0x43809700},
+	{0x8b74, 0x5c010007},
+	{0x8b78, 0x00045c00},
+	{0x8b7c, 0x00014300},
+	{0x8b80, 0x0007427f},
+	{0x8b84, 0x62006280},
+	{0x8b88, 0x00049200},
+	{0x8b8c, 0x00014200},
+	{0x8b90, 0x0007427f},
+	{0x8b94, 0x63146394},
+	{0x8b98, 0x00049100},
+	{0x8b9c, 0x00014200},
+	{0x8ba0, 0x79010004},
+	{0x8ba4, 0xe3757420},
+	{0x8ba8, 0x57005710},
+	{0x8bac, 0xe375e375},
+	{0x8bb0, 0x549f0001},
+	{0x8bb4, 0x5c015400},
+	{0x8bb8, 0x540054df},
+	{0x8bbc, 0x00015c02},
+	{0x8bc0, 0x07145c01},
+	{0x8bc4, 0x5c025400},
+	{0x8bc8, 0x5c020001},
+	{0x8bcc, 0x54000714},
+	{0x8bd0, 0x00015c01},
+	{0x8bd4, 0x4c184c98},
+	{0x8bd8, 0x003f0001},
+	{0x8bdc, 0x00000000},
+	{0x8be0, 0x00000000},
+	{0x8be4, 0x00020000},
+	{0x8be8, 0x00000001},
+	{0x8bec, 0x00000000},
+	{0x8bf0, 0x00000000},
+	{0x8bf4, 0x00000000},
+	{0x8bf8, 0x00010000},
+	{0x8bfc, 0x5c020004},
+	{0x8c00, 0x66076204},
+	{0x8c04, 0x743070c0},
+	{0x8c08, 0x0c010901},
+	{0x8c0c, 0x00010ba6},
+	{0x8080, 0x00000004},
+	{0x8080, 0x00000000},
+	{0x8088, 0x00000000},
+};
+
+static const struct rtw89_txpwr_byrate_cfg rtw89_8852a_txpwr_byrate[] = {
+	{ 0, 0, 0, 0, 4, 0x50505050, },
+	{ 0, 0, 1, 0, 4, 0x50505050, },
+	{ 0, 0, 1, 4, 4, 0x484c5050, },
+	{ 0, 0, 2, 0, 4, 0x50505050, },
+	{ 0, 0, 2, 4, 4, 0x44484c50, },
+	{ 0, 0, 2, 8, 4, 0x34383c40, },
+	{ 0, 0, 3, 0, 4, 0x50505050, },
+	{ 0, 1, 2, 0, 4, 0x50505050, },
+	{ 0, 1, 2, 4, 4, 0x44484c50, },
+	{ 0, 1, 2, 8, 4, 0x34383c40, },
+	{ 0, 1, 3, 0, 4, 0x50505050, },
+	{ 0, 0, 4, 1, 4, 0x00000000, },
+	{ 0, 0, 4, 0, 1, 0x00000000, },
+	{ 1, 0, 1, 0, 4, 0x50505050, },
+	{ 1, 0, 1, 4, 4, 0x484c5050, },
+	{ 1, 0, 2, 0, 4, 0x50505050, },
+	{ 1, 0, 2, 4, 4, 0x44484c50, },
+	{ 1, 0, 2, 8, 4, 0x34383c40, },
+	{ 1, 0, 3, 0, 4, 0x50505050, },
+	{ 1, 1, 2, 0, 4, 0x50505050, },
+	{ 1, 1, 2, 4, 4, 0x44484c50, },
+	{ 1, 1, 2, 8, 4, 0x34383c40, },
+	{ 1, 1, 3, 0, 4, 0x50505050, },
+	{ 1, 0, 4, 0, 4, 0x00000000, },
+};
+
+static const u8 _txpwr_track_delta_swingidx_5gb_n[][DELTA_SWINGIDX_SIZE] = {
+	{0, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 5, 5, 5, 6, 6, 7,
+	 7, 7, 8, 8, 9, 9, 9, 10, 10, 10, 11, 11, 11},
+	{0, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 4, 4, 4,
+	 5, 5, 5, 5, 6, 6, 6, 6, 7, 7, 7, 7, 8, 8},
+	{0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 4, 4, 5, 5,
+	 5, 6, 6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9, 9},
+};
+
+static const u8 _txpwr_track_delta_swingidx_5gb_p[][DELTA_SWINGIDX_SIZE] = {
+	{0, 1, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 6, 6,
+	 6, 7, 7, 7, 8, 8, 8, 9, 9, 10, 10, 10, 11, 11},
+	{0, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 4, 4, 4,
+	 5, 5, 5, 5, 6, 6, 6, 6, 7, 7, 7, 7, 8, 8},
+	{0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 4, 4, 5, 5,
+	 5, 6, 6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9, 9},
+};
+
+static const u8 _txpwr_track_delta_swingidx_5ga_n[][DELTA_SWINGIDX_SIZE] = {
+	{0, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 5, 5, 5, 6, 6, 7,
+	 7, 7, 8, 8, 9, 9, 9, 10, 10, 10, 11, 11, 11},
+	{0, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 4, 4, 4,
+	 5, 5, 5, 5, 6, 6, 6, 6, 7, 7, 7, 7, 8, 8},
+	{0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 4, 4, 5, 5,
+	 5, 6, 6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9, 9},
+};
+
+static const u8 _txpwr_track_delta_swingidx_5ga_p[][DELTA_SWINGIDX_SIZE] = {
+	{0, 1, 1, 1, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 6, 6,
+	 6, 7, 7, 7, 8, 8, 8, 9, 9, 10, 10, 10, 11, 11},
+	{0, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 4, 4, 4, 4,
+	 5, 5, 5, 5, 6, 6, 6, 6, 7, 7, 7, 7, 8, 8},
+	{0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 3, 4, 4, 4, 5, 5,
+	 5, 6, 6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9, 9},
+};
+
+static const u8 _txpwr_track_delta_swingidx_2gb_n[] = {
+	0, 1, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 3, 3, 4,
+	 4, 4, 4, 5, 5, 5, 5, 5, 6, 6, 6, 6, 7, 7};
+
+static const u8 _txpwr_track_delta_swingidx_2gb_p[] = {
+	0, 0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2,
+	 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3, 3};
+
+static const u8 _txpwr_track_delta_swingidx_2ga_n[] = {
+	0, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 3, 3, 3,
+	 3, 3, 3, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 5};
+
+static const u8 _txpwr_track_delta_swingidx_2ga_p[] = {
+	0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 5,
+	 6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9, 9, 10, 10};
+
+static const u8 _txpwr_track_delta_swingidx_2g_cck_b_n[] = {
+	0, 1, 1, 1, 1, 1, 2, 2, 2, 2, 3, 3, 3, 3, 3, 4,
+	 4, 4, 4, 5, 5, 5, 5, 5, 6, 6, 6, 6, 7, 7};
+
+static const u8 _txpwr_track_delta_swingidx_2g_cck_b_p[] = {
+	0, 0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2,
+	 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3, 3};
+
+static const u8 _txpwr_track_delta_swingidx_2g_cck_a_n[] = {
+	0, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 3, 3, 3,
+	 3, 3, 3, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 5};
+
+static const u8 _txpwr_track_delta_swingidx_2g_cck_a_p[] = {
+	0, 1, 1, 1, 2, 2, 2, 3, 3, 3, 4, 4, 4, 5, 5, 5,
+	 6, 6, 6, 7, 7, 7, 8, 8, 8, 9, 9, 9, 10, 10};
+
+const s8 rtw89_8852a_txpwr_lmt_2g[RTW89_2G_BW_NUM][RTW89_NTX_NUM]
+				 [RTW89_RS_LMT_NUM][RTW89_BF_NUM]
+				 [RTW89_REGD_NUM][RTW89_2G_CH_NUM] = {
+	[0][0][0][0][0][0] = 56,
+	[0][0][0][0][0][1] = 56,
+	[0][0][0][0][0][2] = 56,
+	[0][0][0][0][0][3] = 56,
+	[0][0][0][0][0][4] = 56,
+	[0][0][0][0][0][5] = 56,
+	[0][0][0][0][0][6] = 56,
+	[0][0][0][0][0][7] = 56,
+	[0][0][0][0][0][8] = 56,
+	[0][0][0][0][0][9] = 56,
+	[0][0][0][0][0][10] = 56,
+	[0][0][0][0][0][11] = 56,
+	[0][0][0][0][0][12] = 48,
+	[0][0][0][0][0][13] = 76,
+	[0][1][0][0][0][0] = 44,
+	[0][1][0][0][0][1] = 44,
+	[0][1][0][0][0][2] = 44,
+	[0][1][0][0][0][3] = 44,
+	[0][1][0][0][0][4] = 44,
+	[0][1][0][0][0][5] = 44,
+	[0][1][0][0][0][6] = 44,
+	[0][1][0][0][0][7] = 44,
+	[0][1][0][0][0][8] = 44,
+	[0][1][0][0][0][9] = 44,
+	[0][1][0][0][0][10] = 44,
+	[0][1][0][0][0][11] = 44,
+	[0][1][0][0][0][12] = 38,
+	[0][1][0][0][0][13] = 64,
+	[1][0][0][0][0][0] = 0,
+	[1][0][0][0][0][1] = 0,
+	[1][0][0][0][0][2] = 58,
+	[1][0][0][0][0][3] = 58,
+	[1][0][0][0][0][4] = 58,
+	[1][0][0][0][0][5] = 58,
+	[1][0][0][0][0][6] = 46,
+	[1][0][0][0][0][7] = 46,
+	[1][0][0][0][0][8] = 46,
+	[1][0][0][0][0][9] = 32,
+	[1][0][0][0][0][10] = 32,
+	[1][0][0][0][0][11] = 0,
+	[1][0][0][0][0][12] = 0,
+	[1][0][0][0][0][13] = 0,
+	[1][1][0][0][0][0] = 0,
+	[1][1][0][0][0][1] = 0,
+	[1][1][0][0][0][2] = 46,
+	[1][1][0][0][0][3] = 46,
+	[1][1][0][0][0][4] = 46,
+	[1][1][0][0][0][5] = 46,
+	[1][1][0][0][0][6] = 46,
+	[1][1][0][0][0][7] = 46,
+	[1][1][0][0][0][8] = 46,
+	[1][1][0][0][0][9] = 24,
+	[1][1][0][0][0][10] = 24,
+	[1][1][0][0][0][11] = 0,
+	[1][1][0][0][0][12] = 0,
+	[1][1][0][0][0][13] = 0,
+	[0][0][1][0][0][0] = 58,
+	[0][0][1][0][0][1] = 58,
+	[0][0][1][0][0][2] = 58,
+	[0][0][1][0][0][3] = 58,
+	[0][0][1][0][0][4] = 58,
+	[0][0][1][0][0][5] = 58,
+	[0][0][1][0][0][6] = 58,
+	[0][0][1][0][0][7] = 58,
+	[0][0][1][0][0][8] = 58,
+	[0][0][1][0][0][9] = 58,
+	[0][0][1][0][0][10] = 58,
+	[0][0][1][0][0][11] = 56,
+	[0][0][1][0][0][12] = 52,
+	[0][0][1][0][0][13] = 0,
+	[0][1][1][0][0][0] = 46,
+	[0][1][1][0][0][1] = 46,
+	[0][1][1][0][0][2] = 46,
+	[0][1][1][0][0][3] = 46,
+	[0][1][1][0][0][4] = 46,
+	[0][1][1][0][0][5] = 46,
+	[0][1][1][0][0][6] = 46,
+	[0][1][1][0][0][7] = 46,
+	[0][1][1][0][0][8] = 46,
+	[0][1][1][0][0][9] = 46,
+	[0][1][1][0][0][10] = 46,
+	[0][1][1][0][0][11] = 42,
+	[0][1][1][0][0][12] = 40,
+	[0][1][1][0][0][13] = 0,
+	[0][0][2][0][0][0] = 58,
+	[0][0][2][0][0][1] = 58,
+	[0][0][2][0][0][2] = 58,
+	[0][0][2][0][0][3] = 58,
+	[0][0][2][0][0][4] = 58,
+	[0][0][2][0][0][5] = 58,
+	[0][0][2][0][0][6] = 58,
+	[0][0][2][0][0][7] = 58,
+	[0][0][2][0][0][8] = 58,
+	[0][0][2][0][0][9] = 58,
+	[0][0][2][0][0][10] = 58,
+	[0][0][2][0][0][11] = 54,
+	[0][0][2][0][0][12] = 50,
+	[0][0][2][0][0][13] = 0,
+	[0][1][2][0][0][0] = 46,
+	[0][1][2][0][0][1] = 46,
+	[0][1][2][0][0][2] = 46,
+	[0][1][2][0][0][3] = 46,
+	[0][1][2][0][0][4] = 46,
+	[0][1][2][0][0][5] = 46,
+	[0][1][2][0][0][6] = 46,
+	[0][1][2][0][0][7] = 46,
+	[0][1][2][0][0][8] = 46,
+	[0][1][2][0][0][9] = 46,
+	[0][1][2][0][0][10] = 46,
+	[0][1][2][0][0][11] = 42,
+	[0][1][2][0][0][12] = 40,
+	[0][1][2][0][0][13] = 0,
+	[0][1][2][1][0][0] = 34,
+	[0][1][2][1][0][1] = 34,
+	[0][1][2][1][0][2] = 34,
+	[0][1][2][1][0][3] = 34,
+	[0][1][2][1][0][4] = 34,
+	[0][1][2][1][0][5] = 34,
+	[0][1][2][1][0][6] = 34,
+	[0][1][2][1][0][7] = 34,
+	[0][1][2][1][0][8] = 34,
+	[0][1][2][1][0][9] = 34,
+	[0][1][2][1][0][10] = 34,
+	[0][1][2][1][0][11] = 34,
+	[0][1][2][1][0][12] = 34,
+	[0][1][2][1][0][13] = 0,
+	[1][0][2][0][0][0] = 0,
+	[1][0][2][0][0][1] = 0,
+	[1][0][2][0][0][2] = 56,
+	[1][0][2][0][0][3] = 56,
+	[1][0][2][0][0][4] = 58,
+	[1][0][2][0][0][5] = 58,
+	[1][0][2][0][0][6] = 54,
+	[1][0][2][0][0][7] = 50,
+	[1][0][2][0][0][8] = 50,
+	[1][0][2][0][0][9] = 42,
+	[1][0][2][0][0][10] = 40,
+	[1][0][2][0][0][11] = 0,
+	[1][0][2][0][0][12] = 0,
+	[1][0][2][0][0][13] = 0,
+	[1][1][2][0][0][0] = 0,
+	[1][1][2][0][0][1] = 0,
+	[1][1][2][0][0][2] = 46,
+	[1][1][2][0][0][3] = 46,
+	[1][1][2][0][0][4] = 46,
+	[1][1][2][0][0][5] = 46,
+	[1][1][2][0][0][6] = 46,
+	[1][1][2][0][0][7] = 46,
+	[1][1][2][0][0][8] = 46,
+	[1][1][2][0][0][9] = 38,
+	[1][1][2][0][0][10] = 36,
+	[1][1][2][0][0][11] = 0,
+	[1][1][2][0][0][12] = 0,
+	[1][1][2][0][0][13] = 0,
+	[1][1][2][1][0][0] = 0,
+	[1][1][2][1][0][1] = 0,
+	[1][1][2][1][0][2] = 34,
+	[1][1][2][1][0][3] = 34,
+	[1][1][2][1][0][4] = 34,
+	[1][1][2][1][0][5] = 34,
+	[1][1][2][1][0][6] = 34,
+	[1][1][2][1][0][7] = 34,
+	[1][1][2][1][0][8] = 34,
+	[1][1][2][1][0][9] = 34,
+	[1][1][2][1][0][10] = 34,
+	[1][1][2][1][0][11] = 0,
+	[1][1][2][1][0][12] = 0,
+	[1][1][2][1][0][13] = 0,
+	[0][0][0][0][2][0] = 76,
+	[0][0][0][0][1][0] = 56,
+	[0][0][0][0][3][0] = 68,
+	[0][0][0][0][5][0] = 76,
+	[0][0][0][0][6][0] = 56,
+	[0][0][0][0][9][0] = 56,
+	[0][0][0][0][8][0] = 60,
+	[0][0][0][0][11][0] = 56,
+	[0][0][0][0][2][1] = 76,
+	[0][0][0][0][1][1] = 56,
+	[0][0][0][0][3][1] = 68,
+	[0][0][0][0][5][1] = 76,
+	[0][0][0][0][6][1] = 56,
+	[0][0][0][0][9][1] = 56,
+	[0][0][0][0][8][1] = 60,
+	[0][0][0][0][11][1] = 56,
+	[0][0][0][0][2][2] = 76,
+	[0][0][0][0][1][2] = 56,
+	[0][0][0][0][3][2] = 68,
+	[0][0][0][0][5][2] = 76,
+	[0][0][0][0][6][2] = 56,
+	[0][0][0][0][9][2] = 56,
+	[0][0][0][0][8][2] = 60,
+	[0][0][0][0][11][2] = 56,
+	[0][0][0][0][2][3] = 76,
+	[0][0][0][0][1][3] = 56,
+	[0][0][0][0][3][3] = 68,
+	[0][0][0][0][5][3] = 76,
+	[0][0][0][0][6][3] = 56,
+	[0][0][0][0][9][3] = 56,
+	[0][0][0][0][8][3] = 60,
+	[0][0][0][0][11][3] = 56,
+	[0][0][0][0][2][4] = 76,
+	[0][0][0][0][1][4] = 56,
+	[0][0][0][0][3][4] = 68,
+	[0][0][0][0][5][4] = 76,
+	[0][0][0][0][6][4] = 56,
+	[0][0][0][0][9][4] = 56,
+	[0][0][0][0][8][4] = 60,
+	[0][0][0][0][11][4] = 56,
+	[0][0][0][0][2][5] = 76,
+	[0][0][0][0][1][5] = 56,
+	[0][0][0][0][3][5] = 68,
+	[0][0][0][0][5][5] = 76,
+	[0][0][0][0][6][5] = 56,
+	[0][0][0][0][9][5] = 56,
+	[0][0][0][0][8][5] = 60,
+	[0][0][0][0][11][5] = 56,
+	[0][0][0][0][2][6] = 76,
+	[0][0][0][0][1][6] = 56,
+	[0][0][0][0][3][6] = 68,
+	[0][0][0][0][5][6] = 76,
+	[0][0][0][0][6][6] = 56,
+	[0][0][0][0][9][6] = 56,
+	[0][0][0][0][8][6] = 60,
+	[0][0][0][0][11][6] = 56,
+	[0][0][0][0][2][7] = 76,
+	[0][0][0][0][1][7] = 56,
+	[0][0][0][0][3][7] = 68,
+	[0][0][0][0][5][7] = 76,
+	[0][0][0][0][6][7] = 56,
+	[0][0][0][0][9][7] = 56,
+	[0][0][0][0][8][7] = 60,
+	[0][0][0][0][11][7] = 56,
+	[0][0][0][0][2][8] = 76,
+	[0][0][0][0][1][8] = 56,
+	[0][0][0][0][3][8] = 68,
+	[0][0][0][0][5][8] = 76,
+	[0][0][0][0][6][8] = 56,
+	[0][0][0][0][9][8] = 56,
+	[0][0][0][0][8][8] = 60,
+	[0][0][0][0][11][8] = 56,
+	[0][0][0][0][2][9] = 76,
+	[0][0][0][0][1][9] = 56,
+	[0][0][0][0][3][9] = 68,
+	[0][0][0][0][5][9] = 76,
+	[0][0][0][0][6][9] = 56,
+	[0][0][0][0][9][9] = 56,
+	[0][0][0][0][8][9] = 60,
+	[0][0][0][0][11][9] = 56,
+	[0][0][0][0][2][10] = 76,
+	[0][0][0][0][1][10] = 56,
+	[0][0][0][0][3][10] = 68,
+	[0][0][0][0][5][10] = 76,
+	[0][0][0][0][6][10] = 56,
+	[0][0][0][0][9][10] = 56,
+	[0][0][0][0][8][10] = 60,
+	[0][0][0][0][11][10] = 56,
+	[0][0][0][0][2][11] = 68,
+	[0][0][0][0][1][11] = 56,
+	[0][0][0][0][3][11] = 68,
+	[0][0][0][0][5][11] = 68,
+	[0][0][0][0][6][11] = 56,
+	[0][0][0][0][9][11] = 56,
+	[0][0][0][0][8][11] = 60,
+	[0][0][0][0][11][11] = 56,
+	[0][0][0][0][2][12] = 48,
+	[0][0][0][0][1][12] = 56,
+	[0][0][0][0][3][12] = 68,
+	[0][0][0][0][5][12] = 48,
+	[0][0][0][0][6][12] = 56,
+	[0][0][0][0][9][12] = 56,
+	[0][0][0][0][8][12] = 60,
+	[0][0][0][0][11][12] = 56,
+	[0][0][0][0][2][13] = 127,
+	[0][0][0][0][1][13] = 127,
+	[0][0][0][0][3][13] = 76,
+	[0][0][0][0][5][13] = 127,
+	[0][0][0][0][6][13] = 127,
+	[0][0][0][0][9][13] = 127,
+	[0][0][0][0][8][13] = 127,
+	[0][0][0][0][11][13] = 127,
+	[0][1][0][0][2][0] = 74,
+	[0][1][0][0][1][0] = 44,
+	[0][1][0][0][3][0] = 56,
+	[0][1][0][0][5][0] = 74,
+	[0][1][0][0][6][0] = 44,
+	[0][1][0][0][9][0] = 44,
+	[0][1][0][0][8][0] = 48,
+	[0][1][0][0][11][0] = 44,
+	[0][1][0][0][2][1] = 76,
+	[0][1][0][0][1][1] = 44,
+	[0][1][0][0][3][1] = 56,
+	[0][1][0][0][5][1] = 76,
+	[0][1][0][0][6][1] = 44,
+	[0][1][0][0][9][1] = 44,
+	[0][1][0][0][8][1] = 48,
+	[0][1][0][0][11][1] = 44,
+	[0][1][0][0][2][2] = 76,
+	[0][1][0][0][1][2] = 44,
+	[0][1][0][0][3][2] = 56,
+	[0][1][0][0][5][2] = 76,
+	[0][1][0][0][6][2] = 44,
+	[0][1][0][0][9][2] = 44,
+	[0][1][0][0][8][2] = 48,
+	[0][1][0][0][11][2] = 44,
+	[0][1][0][0][2][3] = 76,
+	[0][1][0][0][1][3] = 44,
+	[0][1][0][0][3][3] = 56,
+	[0][1][0][0][5][3] = 76,
+	[0][1][0][0][6][3] = 44,
+	[0][1][0][0][9][3] = 44,
+	[0][1][0][0][8][3] = 48,
+	[0][1][0][0][11][3] = 44,
+	[0][1][0][0][2][4] = 76,
+	[0][1][0][0][1][4] = 44,
+	[0][1][0][0][3][4] = 56,
+	[0][1][0][0][5][4] = 76,
+	[0][1][0][0][6][4] = 44,
+	[0][1][0][0][9][4] = 44,
+	[0][1][0][0][8][4] = 48,
+	[0][1][0][0][11][4] = 44,
+	[0][1][0][0][2][5] = 76,
+	[0][1][0][0][1][5] = 44,
+	[0][1][0][0][3][5] = 56,
+	[0][1][0][0][5][5] = 76,
+	[0][1][0][0][6][5] = 44,
+	[0][1][0][0][9][5] = 44,
+	[0][1][0][0][8][5] = 48,
+	[0][1][0][0][11][5] = 44,
+	[0][1][0][0][2][6] = 76,
+	[0][1][0][0][1][6] = 44,
+	[0][1][0][0][3][6] = 56,
+	[0][1][0][0][5][6] = 76,
+	[0][1][0][0][6][6] = 44,
+	[0][1][0][0][9][6] = 44,
+	[0][1][0][0][8][6] = 48,
+	[0][1][0][0][11][6] = 44,
+	[0][1][0][0][2][7] = 76,
+	[0][1][0][0][1][7] = 44,
+	[0][1][0][0][3][7] = 56,
+	[0][1][0][0][5][7] = 76,
+	[0][1][0][0][6][7] = 44,
+	[0][1][0][0][9][7] = 44,
+	[0][1][0][0][8][7] = 48,
+	[0][1][0][0][11][7] = 44,
+	[0][1][0][0][2][8] = 76,
+	[0][1][0][0][1][8] = 44,
+	[0][1][0][0][3][8] = 56,
+	[0][1][0][0][5][8] = 76,
+	[0][1][0][0][6][8] = 44,
+	[0][1][0][0][9][8] = 44,
+	[0][1][0][0][8][8] = 48,
+	[0][1][0][0][11][8] = 44,
+	[0][1][0][0][2][9] = 76,
+	[0][1][0][0][1][9] = 44,
+	[0][1][0][0][3][9] = 56,
+	[0][1][0][0][5][9] = 76,
+	[0][1][0][0][6][9] = 44,
+	[0][1][0][0][9][9] = 44,
+	[0][1][0][0][8][9] = 48,
+	[0][1][0][0][11][9] = 44,
+	[0][1][0][0][2][10] = 62,
+	[0][1][0][0][1][10] = 44,
+	[0][1][0][0][3][10] = 56,
+	[0][1][0][0][5][10] = 62,
+	[0][1][0][0][6][10] = 44,
+	[0][1][0][0][9][10] = 44,
+	[0][1][0][0][8][10] = 48,
+	[0][1][0][0][11][10] = 44,
+	[0][1][0][0][2][11] = 52,
+	[0][1][0][0][1][11] = 44,
+	[0][1][0][0][3][11] = 56,
+	[0][1][0][0][5][11] = 52,
+	[0][1][0][0][6][11] = 44,
+	[0][1][0][0][9][11] = 44,
+	[0][1][0][0][8][11] = 48,
+	[0][1][0][0][11][11] = 44,
+	[0][1][0][0][2][12] = 38,
+	[0][1][0][0][1][12] = 44,
+	[0][1][0][0][3][12] = 56,
+	[0][1][0][0][5][12] = 38,
+	[0][1][0][0][6][12] = 44,
+	[0][1][0][0][9][12] = 44,
+	[0][1][0][0][8][12] = 48,
+	[0][1][0][0][11][12] = 44,
+	[0][1][0][0][2][13] = 127,
+	[0][1][0][0][1][13] = 127,
+	[0][1][0][0][3][13] = 64,
+	[0][1][0][0][5][13] = 127,
+	[0][1][0][0][6][13] = 127,
+	[0][1][0][0][9][13] = 127,
+	[0][1][0][0][8][13] = 127,
+	[0][1][0][0][11][13] = 127,
+	[1][0][0][0][2][0] = 127,
+	[1][0][0][0][1][0] = 127,
+	[1][0][0][0][3][0] = 127,
+	[1][0][0][0][5][0] = 127,
+	[1][0][0][0][6][0] = 127,
+	[1][0][0][0][9][0] = 127,
+	[1][0][0][0][8][0] = 127,
+	[1][0][0][0][11][0] = 127,
+	[1][0][0][0][2][1] = 127,
+	[1][0][0][0][1][1] = 127,
+	[1][0][0][0][3][1] = 127,
+	[1][0][0][0][5][1] = 127,
+	[1][0][0][0][6][1] = 127,
+	[1][0][0][0][9][1] = 127,
+	[1][0][0][0][8][1] = 127,
+	[1][0][0][0][11][1] = 127,
+	[1][0][0][0][2][2] = 60,
+	[1][0][0][0][1][2] = 58,
+	[1][0][0][0][3][2] = 68,
+	[1][0][0][0][5][2] = 60,
+	[1][0][0][0][6][2] = 58,
+	[1][0][0][0][9][2] = 58,
+	[1][0][0][0][8][2] = 60,
+	[1][0][0][0][11][2] = 58,
+	[1][0][0][0][2][3] = 60,
+	[1][0][0][0][1][3] = 58,
+	[1][0][0][0][3][3] = 68,
+	[1][0][0][0][5][3] = 60,
+	[1][0][0][0][6][3] = 58,
+	[1][0][0][0][9][3] = 58,
+	[1][0][0][0][8][3] = 60,
+	[1][0][0][0][11][3] = 58,
+	[1][0][0][0][2][4] = 60,
+	[1][0][0][0][1][4] = 58,
+	[1][0][0][0][3][4] = 68,
+	[1][0][0][0][5][4] = 60,
+	[1][0][0][0][6][4] = 58,
+	[1][0][0][0][9][4] = 58,
+	[1][0][0][0][8][4] = 60,
+	[1][0][0][0][11][4] = 58,
+	[1][0][0][0][2][5] = 60,
+	[1][0][0][0][1][5] = 58,
+	[1][0][0][0][3][5] = 68,
+	[1][0][0][0][5][5] = 60,
+	[1][0][0][0][6][5] = 58,
+	[1][0][0][0][9][5] = 58,
+	[1][0][0][0][8][5] = 60,
+	[1][0][0][0][11][5] = 58,
+	[1][0][0][0][2][6] = 46,
+	[1][0][0][0][1][6] = 58,
+	[1][0][0][0][3][6] = 68,
+	[1][0][0][0][5][6] = 46,
+	[1][0][0][0][6][6] = 58,
+	[1][0][0][0][9][6] = 58,
+	[1][0][0][0][8][6] = 60,
+	[1][0][0][0][11][6] = 58,
+	[1][0][0][0][2][7] = 46,
+	[1][0][0][0][1][7] = 58,
+	[1][0][0][0][3][7] = 68,
+	[1][0][0][0][5][7] = 46,
+	[1][0][0][0][6][7] = 58,
+	[1][0][0][0][9][7] = 58,
+	[1][0][0][0][8][7] = 60,
+	[1][0][0][0][11][7] = 58,
+	[1][0][0][0][2][8] = 46,
+	[1][0][0][0][1][8] = 58,
+	[1][0][0][0][3][8] = 68,
+	[1][0][0][0][5][8] = 46,
+	[1][0][0][0][6][8] = 58,
+	[1][0][0][0][9][8] = 58,
+	[1][0][0][0][8][8] = 60,
+	[1][0][0][0][11][8] = 58,
+	[1][0][0][0][2][9] = 32,
+	[1][0][0][0][1][9] = 58,
+	[1][0][0][0][3][9] = 68,
+	[1][0][0][0][5][9] = 32,
+	[1][0][0][0][6][9] = 58,
+	[1][0][0][0][9][9] = 58,
+	[1][0][0][0][8][9] = 60,
+	[1][0][0][0][11][9] = 58,
+	[1][0][0][0][2][10] = 32,
+	[1][0][0][0][1][10] = 58,
+	[1][0][0][0][3][10] = 68,
+	[1][0][0][0][5][10] = 32,
+	[1][0][0][0][6][10] = 58,
+	[1][0][0][0][9][10] = 58,
+	[1][0][0][0][8][10] = 60,
+	[1][0][0][0][11][10] = 58,
+	[1][0][0][0][2][11] = 127,
+	[1][0][0][0][1][11] = 127,
+	[1][0][0][0][3][11] = 127,
+	[1][0][0][0][5][11] = 127,
+	[1][0][0][0][6][11] = 127,
+	[1][0][0][0][9][11] = 127,
+	[1][0][0][0][8][11] = 127,
+	[1][0][0][0][11][11] = 127,
+	[1][0][0][0][2][12] = 127,
+	[1][0][0][0][1][12] = 127,
+	[1][0][0][0][3][12] = 127,
+	[1][0][0][0][5][12] = 127,
+	[1][0][0][0][6][12] = 127,
+	[1][0][0][0][9][12] = 127,
+	[1][0][0][0][8][12] = 127,
+	[1][0][0][0][11][12] = 127,
+	[1][0][0][0][2][13] = 127,
+	[1][0][0][0][1][13] = 127,
+	[1][0][0][0][3][13] = 127,
+	[1][0][0][0][5][13] = 127,
+	[1][0][0][0][6][13] = 127,
+	[1][0][0][0][9][13] = 127,
+	[1][0][0][0][8][13] = 127,
+	[1][0][0][0][11][13] = 127,
+	[1][1][0][0][2][0] = 127,
+	[1][1][0][0][1][0] = 127,
+	[1][1][0][0][3][0] = 127,
+	[1][1][0][0][5][0] = 127,
+	[1][1][0][0][6][0] = 127,
+	[1][1][0][0][9][0] = 127,
+	[1][1][0][0][8][0] = 127,
+	[1][1][0][0][11][0] = 127,
+	[1][1][0][0][2][1] = 127,
+	[1][1][0][0][1][1] = 127,
+	[1][1][0][0][3][1] = 127,
+	[1][1][0][0][5][1] = 127,
+	[1][1][0][0][6][1] = 127,
+	[1][1][0][0][9][1] = 127,
+	[1][1][0][0][8][1] = 127,
+	[1][1][0][0][11][1] = 127,
+	[1][1][0][0][2][2] = 48,
+	[1][1][0][0][1][2] = 46,
+	[1][1][0][0][3][2] = 56,
+	[1][1][0][0][5][2] = 48,
+	[1][1][0][0][6][2] = 46,
+	[1][1][0][0][9][2] = 46,
+	[1][1][0][0][8][2] = 48,
+	[1][1][0][0][11][2] = 46,
+	[1][1][0][0][2][3] = 48,
+	[1][1][0][0][1][3] = 46,
+	[1][1][0][0][3][3] = 56,
+	[1][1][0][0][5][3] = 48,
+	[1][1][0][0][6][3] = 46,
+	[1][1][0][0][9][3] = 46,
+	[1][1][0][0][8][3] = 48,
+	[1][1][0][0][11][3] = 46,
+	[1][1][0][0][2][4] = 48,
+	[1][1][0][0][1][4] = 46,
+	[1][1][0][0][3][4] = 56,
+	[1][1][0][0][5][4] = 48,
+	[1][1][0][0][6][4] = 46,
+	[1][1][0][0][9][4] = 46,
+	[1][1][0][0][8][4] = 48,
+	[1][1][0][0][11][4] = 46,
+	[1][1][0][0][2][5] = 58,
+	[1][1][0][0][1][5] = 46,
+	[1][1][0][0][3][5] = 56,
+	[1][1][0][0][5][5] = 58,
+	[1][1][0][0][6][5] = 46,
+	[1][1][0][0][9][5] = 46,
+	[1][1][0][0][8][5] = 48,
+	[1][1][0][0][11][5] = 46,
+	[1][1][0][0][2][6] = 46,
+	[1][1][0][0][1][6] = 46,
+	[1][1][0][0][3][6] = 56,
+	[1][1][0][0][5][6] = 46,
+	[1][1][0][0][6][6] = 46,
+	[1][1][0][0][9][6] = 46,
+	[1][1][0][0][8][6] = 48,
+	[1][1][0][0][11][6] = 46,
+	[1][1][0][0][2][7] = 46,
+	[1][1][0][0][1][7] = 46,
+	[1][1][0][0][3][7] = 56,
+	[1][1][0][0][5][7] = 46,
+	[1][1][0][0][6][7] = 46,
+	[1][1][0][0][9][7] = 46,
+	[1][1][0][0][8][7] = 48,
+	[1][1][0][0][11][7] = 46,
+	[1][1][0][0][2][8] = 46,
+	[1][1][0][0][1][8] = 46,
+	[1][1][0][0][3][8] = 56,
+	[1][1][0][0][5][8] = 46,
+	[1][1][0][0][6][8] = 46,
+	[1][1][0][0][9][8] = 46,
+	[1][1][0][0][8][8] = 48,
+	[1][1][0][0][11][8] = 46,
+	[1][1][0][0][2][9] = 24,
+	[1][1][0][0][1][9] = 46,
+	[1][1][0][0][3][9] = 56,
+	[1][1][0][0][5][9] = 24,
+	[1][1][0][0][6][9] = 46,
+	[1][1][0][0][9][9] = 46,
+	[1][1][0][0][8][9] = 48,
+	[1][1][0][0][11][9] = 46,
+	[1][1][0][0][2][10] = 24,
+	[1][1][0][0][1][10] = 46,
+	[1][1][0][0][3][10] = 56,
+	[1][1][0][0][5][10] = 24,
+	[1][1][0][0][6][10] = 46,
+	[1][1][0][0][9][10] = 46,
+	[1][1][0][0][8][10] = 48,
+	[1][1][0][0][11][10] = 46,
+	[1][1][0][0][2][11] = 127,
+	[1][1][0][0][1][11] = 127,
+	[1][1][0][0][3][11] = 127,
+	[1][1][0][0][5][11] = 127,
+	[1][1][0][0][6][11] = 127,
+	[1][1][0][0][9][11] = 127,
+	[1][1][0][0][8][11] = 127,
+	[1][1][0][0][11][11] = 127,
+	[1][1][0][0][2][12] = 127,
+	[1][1][0][0][1][12] = 127,
+	[1][1][0][0][3][12] = 127,
+	[1][1][0][0][5][12] = 127,
+	[1][1][0][0][6][12] = 127,
+	[1][1][0][0][9][12] = 127,
+	[1][1][0][0][8][12] = 127,
+	[1][1][0][0][11][12] = 127,
+	[1][1][0][0][2][13] = 127,
+	[1][1][0][0][1][13] = 127,
+	[1][1][0][0][3][13] = 127,
+	[1][1][0][0][5][13] = 127,
+	[1][1][0][0][6][13] = 127,
+	[1][1][0][0][9][13] = 127,
+	[1][1][0][0][8][13] = 127,
+	[1][1][0][0][11][13] = 127,
+	[0][0][1][0][2][0] = 66,
+	[0][0][1][0][1][0] = 58,
+	[0][0][1][0][3][0] = 76,
+	[0][0][1][0][5][0] = 66,
+	[0][0][1][0][6][0] = 58,
+	[0][0][1][0][9][0] = 58,
+	[0][0][1][0][8][0] = 60,
+	[0][0][1][0][11][0] = 58,
+	[0][0][1][0][2][1] = 66,
+	[0][0][1][0][1][1] = 58,
+	[0][0][1][0][3][1] = 76,
+	[0][0][1][0][5][1] = 66,
+	[0][0][1][0][6][1] = 58,
+	[0][0][1][0][9][1] = 58,
+	[0][0][1][0][8][1] = 60,
+	[0][0][1][0][11][1] = 58,
+	[0][0][1][0][2][2] = 70,
+	[0][0][1][0][1][2] = 58,
+	[0][0][1][0][3][2] = 76,
+	[0][0][1][0][5][2] = 70,
+	[0][0][1][0][6][2] = 58,
+	[0][0][1][0][9][2] = 58,
+	[0][0][1][0][8][2] = 60,
+	[0][0][1][0][11][2] = 58,
+	[0][0][1][0][2][3] = 74,
+	[0][0][1][0][1][3] = 58,
+	[0][0][1][0][3][3] = 76,
+	[0][0][1][0][5][3] = 74,
+	[0][0][1][0][6][3] = 58,
+	[0][0][1][0][9][3] = 58,
+	[0][0][1][0][8][3] = 60,
+	[0][0][1][0][11][3] = 58,
+	[0][0][1][0][2][4] = 78,
+	[0][0][1][0][1][4] = 58,
+	[0][0][1][0][3][4] = 76,
+	[0][0][1][0][5][4] = 78,
+	[0][0][1][0][6][4] = 58,
+	[0][0][1][0][9][4] = 58,
+	[0][0][1][0][8][4] = 60,
+	[0][0][1][0][11][4] = 58,
+	[0][0][1][0][2][5] = 78,
+	[0][0][1][0][1][5] = 58,
+	[0][0][1][0][3][5] = 76,
+	[0][0][1][0][5][5] = 78,
+	[0][0][1][0][6][5] = 58,
+	[0][0][1][0][9][5] = 58,
+	[0][0][1][0][8][5] = 60,
+	[0][0][1][0][11][5] = 58,
+	[0][0][1][0][2][6] = 78,
+	[0][0][1][0][1][6] = 58,
+	[0][0][1][0][3][6] = 76,
+	[0][0][1][0][5][6] = 78,
+	[0][0][1][0][6][6] = 58,
+	[0][0][1][0][9][6] = 58,
+	[0][0][1][0][8][6] = 60,
+	[0][0][1][0][11][6] = 58,
+	[0][0][1][0][2][7] = 74,
+	[0][0][1][0][1][7] = 58,
+	[0][0][1][0][3][7] = 76,
+	[0][0][1][0][5][7] = 74,
+	[0][0][1][0][6][7] = 58,
+	[0][0][1][0][9][7] = 58,
+	[0][0][1][0][8][7] = 60,
+	[0][0][1][0][11][7] = 58,
+	[0][0][1][0][2][8] = 70,
+	[0][0][1][0][1][8] = 58,
+	[0][0][1][0][3][8] = 76,
+	[0][0][1][0][5][8] = 70,
+	[0][0][1][0][6][8] = 58,
+	[0][0][1][0][9][8] = 58,
+	[0][0][1][0][8][8] = 60,
+	[0][0][1][0][11][8] = 58,
+	[0][0][1][0][2][9] = 66,
+	[0][0][1][0][1][9] = 58,
+	[0][0][1][0][3][9] = 76,
+	[0][0][1][0][5][9] = 66,
+	[0][0][1][0][6][9] = 58,
+	[0][0][1][0][9][9] = 58,
+	[0][0][1][0][8][9] = 60,
+	[0][0][1][0][11][9] = 58,
+	[0][0][1][0][2][10] = 66,
+	[0][0][1][0][1][10] = 58,
+	[0][0][1][0][3][10] = 76,
+	[0][0][1][0][5][10] = 66,
+	[0][0][1][0][6][10] = 58,
+	[0][0][1][0][9][10] = 58,
+	[0][0][1][0][8][10] = 60,
+	[0][0][1][0][11][10] = 58,
+	[0][0][1][0][2][11] = 56,
+	[0][0][1][0][1][11] = 58,
+	[0][0][1][0][3][11] = 76,
+	[0][0][1][0][5][11] = 56,
+	[0][0][1][0][6][11] = 58,
+	[0][0][1][0][9][11] = 58,
+	[0][0][1][0][8][11] = 60,
+	[0][0][1][0][11][11] = 58,
+	[0][0][1][0][2][12] = 52,
+	[0][0][1][0][1][12] = 58,
+	[0][0][1][0][3][12] = 76,
+	[0][0][1][0][5][12] = 52,
+	[0][0][1][0][6][12] = 58,
+	[0][0][1][0][9][12] = 58,
+	[0][0][1][0][8][12] = 60,
+	[0][0][1][0][11][12] = 58,
+	[0][0][1][0][2][13] = 127,
+	[0][0][1][0][1][13] = 127,
+	[0][0][1][0][3][13] = 127,
+	[0][0][1][0][5][13] = 127,
+	[0][0][1][0][6][13] = 127,
+	[0][0][1][0][9][13] = 127,
+	[0][0][1][0][8][13] = 127,
+	[0][0][1][0][11][13] = 127,
+	[0][1][1][0][2][0] = 62,
+	[0][1][1][0][1][0] = 46,
+	[0][1][1][0][3][0] = 64,
+	[0][1][1][0][5][0] = 62,
+	[0][1][1][0][6][0] = 46,
+	[0][1][1][0][9][0] = 46,
+	[0][1][1][0][8][0] = 48,
+	[0][1][1][0][11][0] = 46,
+	[0][1][1][0][2][1] = 62,
+	[0][1][1][0][1][1] = 46,
+	[0][1][1][0][3][1] = 64,
+	[0][1][1][0][5][1] = 62,
+	[0][1][1][0][6][1] = 46,
+	[0][1][1][0][9][1] = 46,
+	[0][1][1][0][8][1] = 48,
+	[0][1][1][0][11][1] = 46,
+	[0][1][1][0][2][2] = 66,
+	[0][1][1][0][1][2] = 46,
+	[0][1][1][0][3][2] = 64,
+	[0][1][1][0][5][2] = 66,
+	[0][1][1][0][6][2] = 46,
+	[0][1][1][0][9][2] = 46,
+	[0][1][1][0][8][2] = 48,
+	[0][1][1][0][11][2] = 46,
+	[0][1][1][0][2][3] = 70,
+	[0][1][1][0][1][3] = 46,
+	[0][1][1][0][3][3] = 64,
+	[0][1][1][0][5][3] = 70,
+	[0][1][1][0][6][3] = 46,
+	[0][1][1][0][9][3] = 46,
+	[0][1][1][0][8][3] = 48,
+	[0][1][1][0][11][3] = 46,
+	[0][1][1][0][2][4] = 78,
+	[0][1][1][0][1][4] = 46,
+	[0][1][1][0][3][4] = 64,
+	[0][1][1][0][5][4] = 78,
+	[0][1][1][0][6][4] = 46,
+	[0][1][1][0][9][4] = 46,
+	[0][1][1][0][8][4] = 48,
+	[0][1][1][0][11][4] = 46,
+	[0][1][1][0][2][5] = 78,
+	[0][1][1][0][1][5] = 46,
+	[0][1][1][0][3][5] = 64,
+	[0][1][1][0][5][5] = 78,
+	[0][1][1][0][6][5] = 46,
+	[0][1][1][0][9][5] = 46,
+	[0][1][1][0][8][5] = 48,
+	[0][1][1][0][11][5] = 46,
+	[0][1][1][0][2][6] = 78,
+	[0][1][1][0][1][6] = 46,
+	[0][1][1][0][3][6] = 64,
+	[0][1][1][0][5][6] = 78,
+	[0][1][1][0][6][6] = 46,
+	[0][1][1][0][9][6] = 46,
+	[0][1][1][0][8][6] = 48,
+	[0][1][1][0][11][6] = 46,
+	[0][1][1][0][2][7] = 70,
+	[0][1][1][0][1][7] = 46,
+	[0][1][1][0][3][7] = 64,
+	[0][1][1][0][5][7] = 70,
+	[0][1][1][0][6][7] = 46,
+	[0][1][1][0][9][7] = 46,
+	[0][1][1][0][8][7] = 48,
+	[0][1][1][0][11][7] = 46,
+	[0][1][1][0][2][8] = 66,
+	[0][1][1][0][1][8] = 46,
+	[0][1][1][0][3][8] = 64,
+	[0][1][1][0][5][8] = 66,
+	[0][1][1][0][6][8] = 46,
+	[0][1][1][0][9][8] = 46,
+	[0][1][1][0][8][8] = 48,
+	[0][1][1][0][11][8] = 46,
+	[0][1][1][0][2][9] = 62,
+	[0][1][1][0][1][9] = 46,
+	[0][1][1][0][3][9] = 64,
+	[0][1][1][0][5][9] = 62,
+	[0][1][1][0][6][9] = 46,
+	[0][1][1][0][9][9] = 46,
+	[0][1][1][0][8][9] = 48,
+	[0][1][1][0][11][9] = 46,
+	[0][1][1][0][2][10] = 62,
+	[0][1][1][0][1][10] = 46,
+	[0][1][1][0][3][10] = 64,
+	[0][1][1][0][5][10] = 62,
+	[0][1][1][0][6][10] = 46,
+	[0][1][1][0][9][10] = 46,
+	[0][1][1][0][8][10] = 48,
+	[0][1][1][0][11][10] = 46,
+	[0][1][1][0][2][11] = 42,
+	[0][1][1][0][1][11] = 46,
+	[0][1][1][0][3][11] = 64,
+	[0][1][1][0][5][11] = 42,
+	[0][1][1][0][6][11] = 46,
+	[0][1][1][0][9][11] = 46,
+	[0][1][1][0][8][11] = 48,
+	[0][1][1][0][11][11] = 46,
+	[0][1][1][0][2][12] = 40,
+	[0][1][1][0][1][12] = 46,
+	[0][1][1][0][3][12] = 64,
+	[0][1][1][0][5][12] = 40,
+	[0][1][1][0][6][12] = 46,
+	[0][1][1][0][9][12] = 46,
+	[0][1][1][0][8][12] = 48,
+	[0][1][1][0][11][12] = 46,
+	[0][1][1][0][2][13] = 127,
+	[0][1][1][0][1][13] = 127,
+	[0][1][1][0][3][13] = 127,
+	[0][1][1][0][5][13] = 127,
+	[0][1][1][0][6][13] = 127,
+	[0][1][1][0][9][13] = 127,
+	[0][1][1][0][8][13] = 127,
+	[0][1][1][0][11][13] = 127,
+	[0][0][2][0][2][0] = 66,
+	[0][0][2][0][1][0] = 58,
+	[0][0][2][0][3][0] = 76,
+	[0][0][2][0][5][0] = 66,
+	[0][0][2][0][6][0] = 58,
+	[0][0][2][0][9][0] = 58,
+	[0][0][2][0][8][0] = 60,
+	[0][0][2][0][11][0] = 58,
+	[0][0][2][0][2][1] = 66,
+	[0][0][2][0][1][1] = 58,
+	[0][0][2][0][3][1] = 76,
+	[0][0][2][0][5][1] = 66,
+	[0][0][2][0][6][1] = 58,
+	[0][0][2][0][9][1] = 58,
+	[0][0][2][0][8][1] = 60,
+	[0][0][2][0][11][1] = 58,
+	[0][0][2][0][2][2] = 70,
+	[0][0][2][0][1][2] = 58,
+	[0][0][2][0][3][2] = 76,
+	[0][0][2][0][5][2] = 70,
+	[0][0][2][0][6][2] = 58,
+	[0][0][2][0][9][2] = 58,
+	[0][0][2][0][8][2] = 60,
+	[0][0][2][0][11][2] = 58,
+	[0][0][2][0][2][3] = 74,
+	[0][0][2][0][1][3] = 58,
+	[0][0][2][0][3][3] = 76,
+	[0][0][2][0][5][3] = 74,
+	[0][0][2][0][6][3] = 58,
+	[0][0][2][0][9][3] = 58,
+	[0][0][2][0][8][3] = 60,
+	[0][0][2][0][11][3] = 58,
+	[0][0][2][0][2][4] = 76,
+	[0][0][2][0][1][4] = 58,
+	[0][0][2][0][3][4] = 76,
+	[0][0][2][0][5][4] = 76,
+	[0][0][2][0][6][4] = 58,
+	[0][0][2][0][9][4] = 58,
+	[0][0][2][0][8][4] = 60,
+	[0][0][2][0][11][4] = 58,
+	[0][0][2][0][2][5] = 76,
+	[0][0][2][0][1][5] = 58,
+	[0][0][2][0][3][5] = 76,
+	[0][0][2][0][5][5] = 76,
+	[0][0][2][0][6][5] = 58,
+	[0][0][2][0][9][5] = 58,
+	[0][0][2][0][8][5] = 60,
+	[0][0][2][0][11][5] = 58,
+	[0][0][2][0][2][6] = 76,
+	[0][0][2][0][1][6] = 58,
+	[0][0][2][0][3][6] = 76,
+	[0][0][2][0][5][6] = 76,
+	[0][0][2][0][6][6] = 58,
+	[0][0][2][0][9][6] = 58,
+	[0][0][2][0][8][6] = 60,
+	[0][0][2][0][11][6] = 58,
+	[0][0][2][0][2][7] = 74,
+	[0][0][2][0][1][7] = 58,
+	[0][0][2][0][3][7] = 76,
+	[0][0][2][0][5][7] = 74,
+	[0][0][2][0][6][7] = 58,
+	[0][0][2][0][9][7] = 58,
+	[0][0][2][0][8][7] = 60,
+	[0][0][2][0][11][7] = 58,
+	[0][0][2][0][2][8] = 70,
+	[0][0][2][0][1][8] = 58,
+	[0][0][2][0][3][8] = 76,
+	[0][0][2][0][5][8] = 70,
+	[0][0][2][0][6][8] = 58,
+	[0][0][2][0][9][8] = 58,
+	[0][0][2][0][8][8] = 60,
+	[0][0][2][0][11][8] = 58,
+	[0][0][2][0][2][9] = 66,
+	[0][0][2][0][1][9] = 58,
+	[0][0][2][0][3][9] = 76,
+	[0][0][2][0][5][9] = 66,
+	[0][0][2][0][6][9] = 58,
+	[0][0][2][0][9][9] = 58,
+	[0][0][2][0][8][9] = 60,
+	[0][0][2][0][11][9] = 58,
+	[0][0][2][0][2][10] = 66,
+	[0][0][2][0][1][10] = 58,
+	[0][0][2][0][3][10] = 76,
+	[0][0][2][0][5][10] = 66,
+	[0][0][2][0][6][10] = 58,
+	[0][0][2][0][9][10] = 58,
+	[0][0][2][0][8][10] = 60,
+	[0][0][2][0][11][10] = 58,
+	[0][0][2][0][2][11] = 54,
+	[0][0][2][0][1][11] = 58,
+	[0][0][2][0][3][11] = 76,
+	[0][0][2][0][5][11] = 54,
+	[0][0][2][0][6][11] = 58,
+	[0][0][2][0][9][11] = 58,
+	[0][0][2][0][8][11] = 60,
+	[0][0][2][0][11][11] = 58,
+	[0][0][2][0][2][12] = 50,
+	[0][0][2][0][1][12] = 58,
+	[0][0][2][0][3][12] = 76,
+	[0][0][2][0][5][12] = 50,
+	[0][0][2][0][6][12] = 58,
+	[0][0][2][0][9][12] = 58,
+	[0][0][2][0][8][12] = 60,
+	[0][0][2][0][11][12] = 58,
+	[0][0][2][0][2][13] = 127,
+	[0][0][2][0][1][13] = 127,
+	[0][0][2][0][3][13] = 127,
+	[0][0][2][0][5][13] = 127,
+	[0][0][2][0][6][13] = 127,
+	[0][0][2][0][9][13] = 127,
+	[0][0][2][0][8][13] = 127,
+	[0][0][2][0][11][13] = 127,
+	[0][1][2][0][2][0] = 62,
+	[0][1][2][0][1][0] = 46,
+	[0][1][2][0][3][0] = 64,
+	[0][1][2][0][5][0] = 62,
+	[0][1][2][0][6][0] = 46,
+	[0][1][2][0][9][0] = 46,
+	[0][1][2][0][8][0] = 48,
+	[0][1][2][0][11][0] = 46,
+	[0][1][2][0][2][1] = 62,
+	[0][1][2][0][1][1] = 46,
+	[0][1][2][0][3][1] = 64,
+	[0][1][2][0][5][1] = 62,
+	[0][1][2][0][6][1] = 46,
+	[0][1][2][0][9][1] = 46,
+	[0][1][2][0][8][1] = 48,
+	[0][1][2][0][11][1] = 46,
+	[0][1][2][0][2][2] = 66,
+	[0][1][2][0][1][2] = 46,
+	[0][1][2][0][3][2] = 64,
+	[0][1][2][0][5][2] = 66,
+	[0][1][2][0][6][2] = 46,
+	[0][1][2][0][9][2] = 46,
+	[0][1][2][0][8][2] = 48,
+	[0][1][2][0][11][2] = 46,
+	[0][1][2][0][2][3] = 70,
+	[0][1][2][0][1][3] = 46,
+	[0][1][2][0][3][3] = 64,
+	[0][1][2][0][5][3] = 70,
+	[0][1][2][0][6][3] = 46,
+	[0][1][2][0][9][3] = 46,
+	[0][1][2][0][8][3] = 48,
+	[0][1][2][0][11][3] = 46,
+	[0][1][2][0][2][4] = 76,
+	[0][1][2][0][1][4] = 46,
+	[0][1][2][0][3][4] = 64,
+	[0][1][2][0][5][4] = 76,
+	[0][1][2][0][6][4] = 46,
+	[0][1][2][0][9][4] = 46,
+	[0][1][2][0][8][4] = 48,
+	[0][1][2][0][11][4] = 46,
+	[0][1][2][0][2][5] = 76,
+	[0][1][2][0][1][5] = 46,
+	[0][1][2][0][3][5] = 64,
+	[0][1][2][0][5][5] = 76,
+	[0][1][2][0][6][5] = 46,
+	[0][1][2][0][9][5] = 46,
+	[0][1][2][0][8][5] = 48,
+	[0][1][2][0][11][5] = 46,
+	[0][1][2][0][2][6] = 76,
+	[0][1][2][0][1][6] = 46,
+	[0][1][2][0][3][6] = 64,
+	[0][1][2][0][5][6] = 76,
+	[0][1][2][0][6][6] = 46,
+	[0][1][2][0][9][6] = 46,
+	[0][1][2][0][8][6] = 48,
+	[0][1][2][0][11][6] = 46,
+	[0][1][2][0][2][7] = 68,
+	[0][1][2][0][1][7] = 46,
+	[0][1][2][0][3][7] = 64,
+	[0][1][2][0][5][7] = 68,
+	[0][1][2][0][6][7] = 46,
+	[0][1][2][0][9][7] = 46,
+	[0][1][2][0][8][7] = 48,
+	[0][1][2][0][11][7] = 46,
+	[0][1][2][0][2][8] = 64,
+	[0][1][2][0][1][8] = 46,
+	[0][1][2][0][3][8] = 64,
+	[0][1][2][0][5][8] = 64,
+	[0][1][2][0][6][8] = 46,
+	[0][1][2][0][9][8] = 46,
+	[0][1][2][0][8][8] = 48,
+	[0][1][2][0][11][8] = 46,
+	[0][1][2][0][2][9] = 60,
+	[0][1][2][0][1][9] = 46,
+	[0][1][2][0][3][9] = 64,
+	[0][1][2][0][5][9] = 60,
+	[0][1][2][0][6][9] = 46,
+	[0][1][2][0][9][9] = 46,
+	[0][1][2][0][8][9] = 48,
+	[0][1][2][0][11][9] = 46,
+	[0][1][2][0][2][10] = 60,
+	[0][1][2][0][1][10] = 46,
+	[0][1][2][0][3][10] = 64,
+	[0][1][2][0][5][10] = 60,
+	[0][1][2][0][6][10] = 46,
+	[0][1][2][0][9][10] = 46,
+	[0][1][2][0][8][10] = 48,
+	[0][1][2][0][11][10] = 46,
+	[0][1][2][0][2][11] = 42,
+	[0][1][2][0][1][11] = 46,
+	[0][1][2][0][3][11] = 64,
+	[0][1][2][0][5][11] = 42,
+	[0][1][2][0][6][11] = 46,
+	[0][1][2][0][9][11] = 46,
+	[0][1][2][0][8][11] = 48,
+	[0][1][2][0][11][11] = 46,
+	[0][1][2][0][2][12] = 40,
+	[0][1][2][0][1][12] = 46,
+	[0][1][2][0][3][12] = 64,
+	[0][1][2][0][5][12] = 40,
+	[0][1][2][0][6][12] = 46,
+	[0][1][2][0][9][12] = 46,
+	[0][1][2][0][8][12] = 48,
+	[0][1][2][0][11][12] = 46,
+	[0][1][2][0][2][13] = 127,
+	[0][1][2][0][1][13] = 127,
+	[0][1][2][0][3][13] = 127,
+	[0][1][2][0][5][13] = 127,
+	[0][1][2][0][6][13] = 127,
+	[0][1][2][0][9][13] = 127,
+	[0][1][2][0][8][13] = 127,
+	[0][1][2][0][11][13] = 127,
+	[0][1][2][1][2][0] = 62,
+	[0][1][2][1][1][0] = 34,
+	[0][1][2][1][3][0] = 64,
+	[0][1][2][1][5][0] = 62,
+	[0][1][2][1][6][0] = 34,
+	[0][1][2][1][9][0] = 34,
+	[0][1][2][1][8][0] = 36,
+	[0][1][2][1][11][0] = 34,
+	[0][1][2][1][2][1] = 62,
+	[0][1][2][1][1][1] = 34,
+	[0][1][2][1][3][1] = 64,
+	[0][1][2][1][5][1] = 62,
+	[0][1][2][1][6][1] = 34,
+	[0][1][2][1][9][1] = 34,
+	[0][1][2][1][8][1] = 36,
+	[0][1][2][1][11][1] = 34,
+	[0][1][2][1][2][2] = 66,
+	[0][1][2][1][1][2] = 34,
+	[0][1][2][1][3][2] = 64,
+	[0][1][2][1][5][2] = 66,
+	[0][1][2][1][6][2] = 34,
+	[0][1][2][1][9][2] = 34,
+	[0][1][2][1][8][2] = 36,
+	[0][1][2][1][11][2] = 34,
+	[0][1][2][1][2][3] = 70,
+	[0][1][2][1][1][3] = 34,
+	[0][1][2][1][3][3] = 64,
+	[0][1][2][1][5][3] = 70,
+	[0][1][2][1][6][3] = 34,
+	[0][1][2][1][9][3] = 34,
+	[0][1][2][1][8][3] = 36,
+	[0][1][2][1][11][3] = 34,
+	[0][1][2][1][2][4] = 76,
+	[0][1][2][1][1][4] = 34,
+	[0][1][2][1][3][4] = 64,
+	[0][1][2][1][5][4] = 76,
+	[0][1][2][1][6][4] = 34,
+	[0][1][2][1][9][4] = 34,
+	[0][1][2][1][8][4] = 36,
+	[0][1][2][1][11][4] = 34,
+	[0][1][2][1][2][5] = 76,
+	[0][1][2][1][1][5] = 34,
+	[0][1][2][1][3][5] = 64,
+	[0][1][2][1][5][5] = 76,
+	[0][1][2][1][6][5] = 34,
+	[0][1][2][1][9][5] = 34,
+	[0][1][2][1][8][5] = 36,
+	[0][1][2][1][11][5] = 34,
+	[0][1][2][1][2][6] = 76,
+	[0][1][2][1][1][6] = 34,
+	[0][1][2][1][3][6] = 64,
+	[0][1][2][1][5][6] = 76,
+	[0][1][2][1][6][6] = 34,
+	[0][1][2][1][9][6] = 34,
+	[0][1][2][1][8][6] = 36,
+	[0][1][2][1][11][6] = 34,
+	[0][1][2][1][2][7] = 68,
+	[0][1][2][1][1][7] = 34,
+	[0][1][2][1][3][7] = 64,
+	[0][1][2][1][5][7] = 68,
+	[0][1][2][1][6][7] = 34,
+	[0][1][2][1][9][7] = 34,
+	[0][1][2][1][8][7] = 36,
+	[0][1][2][1][11][7] = 34,
+	[0][1][2][1][2][8] = 64,
+	[0][1][2][1][1][8] = 34,
+	[0][1][2][1][3][8] = 64,
+	[0][1][2][1][5][8] = 64,
+	[0][1][2][1][6][8] = 34,
+	[0][1][2][1][9][8] = 34,
+	[0][1][2][1][8][8] = 36,
+	[0][1][2][1][11][8] = 34,
+	[0][1][2][1][2][9] = 60,
+	[0][1][2][1][1][9] = 34,
+	[0][1][2][1][3][9] = 64,
+	[0][1][2][1][5][9] = 60,
+	[0][1][2][1][6][9] = 34,
+	[0][1][2][1][9][9] = 34,
+	[0][1][2][1][8][9] = 36,
+	[0][1][2][1][11][9] = 34,
+	[0][1][2][1][2][10] = 60,
+	[0][1][2][1][1][10] = 34,
+	[0][1][2][1][3][10] = 64,
+	[0][1][2][1][5][10] = 60,
+	[0][1][2][1][6][10] = 34,
+	[0][1][2][1][9][10] = 34,
+	[0][1][2][1][8][10] = 36,
+	[0][1][2][1][11][10] = 34,
+	[0][1][2][1][2][11] = 42,
+	[0][1][2][1][1][11] = 34,
+	[0][1][2][1][3][11] = 64,
+	[0][1][2][1][5][11] = 42,
+	[0][1][2][1][6][11] = 34,
+	[0][1][2][1][9][11] = 34,
+	[0][1][2][1][8][11] = 36,
+	[0][1][2][1][11][11] = 34,
+	[0][1][2][1][2][12] = 40,
+	[0][1][2][1][1][12] = 34,
+	[0][1][2][1][3][12] = 64,
+	[0][1][2][1][5][12] = 40,
+	[0][1][2][1][6][12] = 34,
+	[0][1][2][1][9][12] = 34,
+	[0][1][2][1][8][12] = 36,
+	[0][1][2][1][11][12] = 34,
+	[0][1][2][1][2][13] = 127,
+	[0][1][2][1][1][13] = 127,
+	[0][1][2][1][3][13] = 127,
+	[0][1][2][1][5][13] = 127,
+	[0][1][2][1][6][13] = 127,
+	[0][1][2][1][9][13] = 127,
+	[0][1][2][1][8][13] = 127,
+	[0][1][2][1][11][13] = 127,
+	[1][0][2][0][2][0] = 127,
+	[1][0][2][0][1][0] = 127,
+	[1][0][2][0][3][0] = 127,
+	[1][0][2][0][5][0] = 127,
+	[1][0][2][0][6][0] = 127,
+	[1][0][2][0][9][0] = 127,
+	[1][0][2][0][8][0] = 127,
+	[1][0][2][0][11][0] = 127,
+	[1][0][2][0][2][1] = 127,
+	[1][0][2][0][1][1] = 127,
+	[1][0][2][0][3][1] = 127,
+	[1][0][2][0][5][1] = 127,
+	[1][0][2][0][6][1] = 127,
+	[1][0][2][0][9][1] = 127,
+	[1][0][2][0][8][1] = 127,
+	[1][0][2][0][11][1] = 127,
+	[1][0][2][0][2][2] = 56,
+	[1][0][2][0][1][2] = 58,
+	[1][0][2][0][3][2] = 76,
+	[1][0][2][0][5][2] = 56,
+	[1][0][2][0][6][2] = 58,
+	[1][0][2][0][9][2] = 58,
+	[1][0][2][0][8][2] = 60,
+	[1][0][2][0][11][2] = 58,
+	[1][0][2][0][2][3] = 56,
+	[1][0][2][0][1][3] = 58,
+	[1][0][2][0][3][3] = 76,
+	[1][0][2][0][5][3] = 56,
+	[1][0][2][0][6][3] = 58,
+	[1][0][2][0][9][3] = 58,
+	[1][0][2][0][8][3] = 60,
+	[1][0][2][0][11][3] = 58,
+	[1][0][2][0][2][4] = 60,
+	[1][0][2][0][1][4] = 58,
+	[1][0][2][0][3][4] = 76,
+	[1][0][2][0][5][4] = 60,
+	[1][0][2][0][6][4] = 58,
+	[1][0][2][0][9][4] = 58,
+	[1][0][2][0][8][4] = 60,
+	[1][0][2][0][11][4] = 58,
+	[1][0][2][0][2][5] = 64,
+	[1][0][2][0][1][5] = 58,
+	[1][0][2][0][3][5] = 76,
+	[1][0][2][0][5][5] = 64,
+	[1][0][2][0][6][5] = 58,
+	[1][0][2][0][9][5] = 58,
+	[1][0][2][0][8][5] = 60,
+	[1][0][2][0][11][5] = 58,
+	[1][0][2][0][2][6] = 54,
+	[1][0][2][0][1][6] = 58,
+	[1][0][2][0][3][6] = 76,
+	[1][0][2][0][5][6] = 54,
+	[1][0][2][0][6][6] = 58,
+	[1][0][2][0][9][6] = 58,
+	[1][0][2][0][8][6] = 60,
+	[1][0][2][0][11][6] = 58,
+	[1][0][2][0][2][7] = 50,
+	[1][0][2][0][1][7] = 58,
+	[1][0][2][0][3][7] = 76,
+	[1][0][2][0][5][7] = 50,
+	[1][0][2][0][6][7] = 58,
+	[1][0][2][0][9][7] = 58,
+	[1][0][2][0][8][7] = 60,
+	[1][0][2][0][11][7] = 58,
+	[1][0][2][0][2][8] = 50,
+	[1][0][2][0][1][8] = 58,
+	[1][0][2][0][3][8] = 76,
+	[1][0][2][0][5][8] = 50,
+	[1][0][2][0][6][8] = 58,
+	[1][0][2][0][9][8] = 58,
+	[1][0][2][0][8][8] = 60,
+	[1][0][2][0][11][8] = 58,
+	[1][0][2][0][2][9] = 42,
+	[1][0][2][0][1][9] = 58,
+	[1][0][2][0][3][9] = 76,
+	[1][0][2][0][5][9] = 42,
+	[1][0][2][0][6][9] = 58,
+	[1][0][2][0][9][9] = 58,
+	[1][0][2][0][8][9] = 60,
+	[1][0][2][0][11][9] = 58,
+	[1][0][2][0][2][10] = 40,
+	[1][0][2][0][1][10] = 58,
+	[1][0][2][0][3][10] = 76,
+	[1][0][2][0][5][10] = 40,
+	[1][0][2][0][6][10] = 58,
+	[1][0][2][0][9][10] = 58,
+	[1][0][2][0][8][10] = 60,
+	[1][0][2][0][11][10] = 58,
+	[1][0][2][0][2][11] = 127,
+	[1][0][2][0][1][11] = 127,
+	[1][0][2][0][3][11] = 127,
+	[1][0][2][0][5][11] = 127,
+	[1][0][2][0][6][11] = 127,
+	[1][0][2][0][9][11] = 127,
+	[1][0][2][0][8][11] = 127,
+	[1][0][2][0][11][11] = 127,
+	[1][0][2][0][2][12] = 127,
+	[1][0][2][0][1][12] = 127,
+	[1][0][2][0][3][12] = 127,
+	[1][0][2][0][5][12] = 127,
+	[1][0][2][0][6][12] = 127,
+	[1][0][2][0][9][12] = 127,
+	[1][0][2][0][8][12] = 127,
+	[1][0][2][0][11][12] = 127,
+	[1][0][2][0][2][13] = 127,
+	[1][0][2][0][1][13] = 127,
+	[1][0][2][0][3][13] = 127,
+	[1][0][2][0][5][13] = 127,
+	[1][0][2][0][6][13] = 127,
+	[1][0][2][0][9][13] = 127,
+	[1][0][2][0][8][13] = 127,
+	[1][0][2][0][11][13] = 127,
+	[1][1][2][0][2][0] = 127,
+	[1][1][2][0][1][0] = 127,
+	[1][1][2][0][3][0] = 127,
+	[1][1][2][0][5][0] = 127,
+	[1][1][2][0][6][0] = 127,
+	[1][1][2][0][9][0] = 127,
+	[1][1][2][0][8][0] = 127,
+	[1][1][2][0][11][0] = 127,
+	[1][1][2][0][2][1] = 127,
+	[1][1][2][0][1][1] = 127,
+	[1][1][2][0][3][1] = 127,
+	[1][1][2][0][5][1] = 127,
+	[1][1][2][0][6][1] = 127,
+	[1][1][2][0][9][1] = 127,
+	[1][1][2][0][8][1] = 127,
+	[1][1][2][0][11][1] = 127,
+	[1][1][2][0][2][2] = 52,
+	[1][1][2][0][1][2] = 46,
+	[1][1][2][0][3][2] = 64,
+	[1][1][2][0][5][2] = 52,
+	[1][1][2][0][6][2] = 46,
+	[1][1][2][0][9][2] = 46,
+	[1][1][2][0][8][2] = 48,
+	[1][1][2][0][11][2] = 46,
+	[1][1][2][0][2][3] = 52,
+	[1][1][2][0][1][3] = 46,
+	[1][1][2][0][3][3] = 64,
+	[1][1][2][0][5][3] = 52,
+	[1][1][2][0][6][3] = 46,
+	[1][1][2][0][9][3] = 46,
+	[1][1][2][0][8][3] = 48,
+	[1][1][2][0][11][3] = 46,
+	[1][1][2][0][2][4] = 56,
+	[1][1][2][0][1][4] = 46,
+	[1][1][2][0][3][4] = 64,
+	[1][1][2][0][5][4] = 56,
+	[1][1][2][0][6][4] = 46,
+	[1][1][2][0][9][4] = 46,
+	[1][1][2][0][8][4] = 48,
+	[1][1][2][0][11][4] = 46,
+	[1][1][2][0][2][5] = 60,
+	[1][1][2][0][1][5] = 46,
+	[1][1][2][0][3][5] = 64,
+	[1][1][2][0][5][5] = 60,
+	[1][1][2][0][6][5] = 46,
+	[1][1][2][0][9][5] = 46,
+	[1][1][2][0][8][5] = 48,
+	[1][1][2][0][11][5] = 46,
+	[1][1][2][0][2][6] = 54,
+	[1][1][2][0][1][6] = 46,
+	[1][1][2][0][3][6] = 64,
+	[1][1][2][0][5][6] = 52,
+	[1][1][2][0][6][6] = 46,
+	[1][1][2][0][9][6] = 46,
+	[1][1][2][0][8][6] = 48,
+	[1][1][2][0][11][6] = 46,
+	[1][1][2][0][2][7] = 50,
+	[1][1][2][0][1][7] = 46,
+	[1][1][2][0][3][7] = 64,
+	[1][1][2][0][5][7] = 48,
+	[1][1][2][0][6][7] = 46,
+	[1][1][2][0][9][7] = 46,
+	[1][1][2][0][8][7] = 48,
+	[1][1][2][0][11][7] = 46,
+	[1][1][2][0][2][8] = 50,
+	[1][1][2][0][1][8] = 46,
+	[1][1][2][0][3][8] = 64,
+	[1][1][2][0][5][8] = 48,
+	[1][1][2][0][6][8] = 46,
+	[1][1][2][0][9][8] = 46,
+	[1][1][2][0][8][8] = 48,
+	[1][1][2][0][11][8] = 46,
+	[1][1][2][0][2][9] = 38,
+	[1][1][2][0][1][9] = 46,
+	[1][1][2][0][3][9] = 64,
+	[1][1][2][0][5][9] = 38,
+	[1][1][2][0][6][9] = 46,
+	[1][1][2][0][9][9] = 46,
+	[1][1][2][0][8][9] = 48,
+	[1][1][2][0][11][9] = 46,
+	[1][1][2][0][2][10] = 36,
+	[1][1][2][0][1][10] = 46,
+	[1][1][2][0][3][10] = 64,
+	[1][1][2][0][5][10] = 36,
+	[1][1][2][0][6][10] = 46,
+	[1][1][2][0][9][10] = 46,
+	[1][1][2][0][8][10] = 48,
+	[1][1][2][0][11][10] = 46,
+	[1][1][2][0][2][11] = 127,
+	[1][1][2][0][1][11] = 127,
+	[1][1][2][0][3][11] = 127,
+	[1][1][2][0][5][11] = 127,
+	[1][1][2][0][6][11] = 127,
+	[1][1][2][0][9][11] = 127,
+	[1][1][2][0][8][11] = 127,
+	[1][1][2][0][11][11] = 127,
+	[1][1][2][0][2][12] = 127,
+	[1][1][2][0][1][12] = 127,
+	[1][1][2][0][3][12] = 127,
+	[1][1][2][0][5][12] = 127,
+	[1][1][2][0][6][12] = 127,
+	[1][1][2][0][9][12] = 127,
+	[1][1][2][0][8][12] = 127,
+	[1][1][2][0][11][12] = 127,
+	[1][1][2][0][2][13] = 127,
+	[1][1][2][0][1][13] = 127,
+	[1][1][2][0][3][13] = 127,
+	[1][1][2][0][5][13] = 127,
+	[1][1][2][0][6][13] = 127,
+	[1][1][2][0][9][13] = 127,
+	[1][1][2][0][8][13] = 127,
+	[1][1][2][0][11][13] = 127,
+	[1][1][2][1][2][0] = 127,
+	[1][1][2][1][1][0] = 127,
+	[1][1][2][1][3][0] = 127,
+	[1][1][2][1][5][0] = 127,
+	[1][1][2][1][6][0] = 127,
+	[1][1][2][1][9][0] = 127,
+	[1][1][2][1][8][0] = 127,
+	[1][1][2][1][11][0] = 127,
+	[1][1][2][1][2][1] = 127,
+	[1][1][2][1][1][1] = 127,
+	[1][1][2][1][3][1] = 127,
+	[1][1][2][1][5][1] = 127,
+	[1][1][2][1][6][1] = 127,
+	[1][1][2][1][9][1] = 127,
+	[1][1][2][1][8][1] = 127,
+	[1][1][2][1][11][1] = 127,
+	[1][1][2][1][2][2] = 52,
+	[1][1][2][1][1][2] = 34,
+	[1][1][2][1][3][2] = 64,
+	[1][1][2][1][5][2] = 52,
+	[1][1][2][1][6][2] = 34,
+	[1][1][2][1][9][2] = 34,
+	[1][1][2][1][8][2] = 36,
+	[1][1][2][1][11][2] = 34,
+	[1][1][2][1][2][3] = 52,
+	[1][1][2][1][1][3] = 34,
+	[1][1][2][1][3][3] = 64,
+	[1][1][2][1][5][3] = 52,
+	[1][1][2][1][6][3] = 34,
+	[1][1][2][1][9][3] = 34,
+	[1][1][2][1][8][3] = 36,
+	[1][1][2][1][11][3] = 34,
+	[1][1][2][1][2][4] = 56,
+	[1][1][2][1][1][4] = 34,
+	[1][1][2][1][3][4] = 64,
+	[1][1][2][1][5][4] = 56,
+	[1][1][2][1][6][4] = 34,
+	[1][1][2][1][9][4] = 34,
+	[1][1][2][1][8][4] = 36,
+	[1][1][2][1][11][4] = 34,
+	[1][1][2][1][2][5] = 60,
+	[1][1][2][1][1][5] = 34,
+	[1][1][2][1][3][5] = 64,
+	[1][1][2][1][5][5] = 60,
+	[1][1][2][1][6][5] = 34,
+	[1][1][2][1][9][5] = 34,
+	[1][1][2][1][8][5] = 36,
+	[1][1][2][1][11][5] = 34,
+	[1][1][2][1][2][6] = 54,
+	[1][1][2][1][1][6] = 34,
+	[1][1][2][1][3][6] = 64,
+	[1][1][2][1][5][6] = 52,
+	[1][1][2][1][6][6] = 34,
+	[1][1][2][1][9][6] = 34,
+	[1][1][2][1][8][6] = 36,
+	[1][1][2][1][11][6] = 34,
+	[1][1][2][1][2][7] = 50,
+	[1][1][2][1][1][7] = 34,
+	[1][1][2][1][3][7] = 64,
+	[1][1][2][1][5][7] = 48,
+	[1][1][2][1][6][7] = 34,
+	[1][1][2][1][9][7] = 34,
+	[1][1][2][1][8][7] = 36,
+	[1][1][2][1][11][7] = 34,
+	[1][1][2][1][2][8] = 50,
+	[1][1][2][1][1][8] = 34,
+	[1][1][2][1][3][8] = 64,
+	[1][1][2][1][5][8] = 48,
+	[1][1][2][1][6][8] = 34,
+	[1][1][2][1][9][8] = 34,
+	[1][1][2][1][8][8] = 36,
+	[1][1][2][1][11][8] = 34,
+	[1][1][2][1][2][9] = 38,
+	[1][1][2][1][1][9] = 34,
+	[1][1][2][1][3][9] = 64,
+	[1][1][2][1][5][9] = 38,
+	[1][1][2][1][6][9] = 34,
+	[1][1][2][1][9][9] = 34,
+	[1][1][2][1][8][9] = 36,
+	[1][1][2][1][11][9] = 34,
+	[1][1][2][1][2][10] = 36,
+	[1][1][2][1][1][10] = 34,
+	[1][1][2][1][3][10] = 64,
+	[1][1][2][1][5][10] = 36,
+	[1][1][2][1][6][10] = 34,
+	[1][1][2][1][9][10] = 34,
+	[1][1][2][1][8][10] = 36,
+	[1][1][2][1][11][10] = 34,
+	[1][1][2][1][2][11] = 127,
+	[1][1][2][1][1][11] = 127,
+	[1][1][2][1][3][11] = 127,
+	[1][1][2][1][5][11] = 127,
+	[1][1][2][1][6][11] = 127,
+	[1][1][2][1][9][11] = 127,
+	[1][1][2][1][8][11] = 127,
+	[1][1][2][1][11][11] = 127,
+	[1][1][2][1][2][12] = 127,
+	[1][1][2][1][1][12] = 127,
+	[1][1][2][1][3][12] = 127,
+	[1][1][2][1][5][12] = 127,
+	[1][1][2][1][6][12] = 127,
+	[1][1][2][1][9][12] = 127,
+	[1][1][2][1][8][12] = 127,
+	[1][1][2][1][11][12] = 127,
+	[1][1][2][1][2][13] = 127,
+	[1][1][2][1][1][13] = 127,
+	[1][1][2][1][3][13] = 127,
+	[1][1][2][1][5][13] = 127,
+	[1][1][2][1][6][13] = 127,
+	[1][1][2][1][9][13] = 127,
+	[1][1][2][1][8][13] = 127,
+	[1][1][2][1][11][13] = 127,
+};
+
+const s8 rtw89_8852a_txpwr_lmt_5g[RTW89_5G_BW_NUM][RTW89_NTX_NUM]
+				 [RTW89_RS_LMT_NUM][RTW89_BF_NUM]
+				 [RTW89_REGD_NUM][RTW89_5G_CH_NUM] = {
+	[0][0][1][0][0][0] = 30,
+	[0][0][1][0][0][2] = 30,
+	[0][0][1][0][0][4] = 30,
+	[0][0][1][0][0][6] = 30,
+	[0][0][1][0][0][8] = 52,
+	[0][0][1][0][0][10] = 52,
+	[0][0][1][0][0][12] = 52,
+	[0][0][1][0][0][14] = 52,
+	[0][0][1][0][0][15] = 52,
+	[0][0][1][0][0][17] = 52,
+	[0][0][1][0][0][19] = 52,
+	[0][0][1][0][0][21] = 52,
+	[0][0][1][0][0][23] = 52,
+	[0][0][1][0][0][25] = 52,
+	[0][0][1][0][0][27] = 52,
+	[0][0][1][0][0][29] = 52,
+	[0][0][1][0][0][31] = 52,
+	[0][0][1][0][0][33] = 52,
+	[0][0][1][0][0][35] = 52,
+	[0][0][1][0][0][37] = 54,
+	[0][0][1][0][0][38] = 28,
+	[0][0][1][0][0][40] = 28,
+	[0][0][1][0][0][42] = 28,
+	[0][0][1][0][0][44] = 28,
+	[0][0][1][0][0][46] = 28,
+	[0][1][1][0][0][0] = 18,
+	[0][1][1][0][0][2] = 18,
+	[0][1][1][0][0][4] = 18,
+	[0][1][1][0][0][6] = 18,
+	[0][1][1][0][0][8] = 40,
+	[0][1][1][0][0][10] = 40,
+	[0][1][1][0][0][12] = 40,
+	[0][1][1][0][0][14] = 40,
+	[0][1][1][0][0][15] = 40,
+	[0][1][1][0][0][17] = 40,
+	[0][1][1][0][0][19] = 40,
+	[0][1][1][0][0][21] = 40,
+	[0][1][1][0][0][23] = 40,
+	[0][1][1][0][0][25] = 40,
+	[0][1][1][0][0][27] = 40,
+	[0][1][1][0][0][29] = 40,
+	[0][1][1][0][0][31] = 40,
+	[0][1][1][0][0][33] = 40,
+	[0][1][1][0][0][35] = 40,
+	[0][1][1][0][0][37] = 42,
+	[0][1][1][0][0][38] = 16,
+	[0][1][1][0][0][40] = 16,
+	[0][1][1][0][0][42] = 16,
+	[0][1][1][0][0][44] = 16,
+	[0][1][1][0][0][46] = 16,
+	[0][0][2][0][0][0] = 30,
+	[0][0][2][0][0][2] = 30,
+	[0][0][2][0][0][4] = 30,
+	[0][0][2][0][0][6] = 30,
+	[0][0][2][0][0][8] = 52,
+	[0][0][2][0][0][10] = 52,
+	[0][0][2][0][0][12] = 52,
+	[0][0][2][0][0][14] = 52,
+	[0][0][2][0][0][15] = 52,
+	[0][0][2][0][0][17] = 52,
+	[0][0][2][0][0][19] = 52,
+	[0][0][2][0][0][21] = 52,
+	[0][0][2][0][0][23] = 52,
+	[0][0][2][0][0][25] = 52,
+	[0][0][2][0][0][27] = 52,
+	[0][0][2][0][0][29] = 52,
+	[0][0][2][0][0][31] = 52,
+	[0][0][2][0][0][33] = 52,
+	[0][0][2][0][0][35] = 52,
+	[0][0][2][0][0][37] = 54,
+	[0][0][2][0][0][38] = 28,
+	[0][0][2][0][0][40] = 28,
+	[0][0][2][0][0][42] = 28,
+	[0][0][2][0][0][44] = 28,
+	[0][0][2][0][0][46] = 28,
+	[0][1][2][0][0][0] = 18,
+	[0][1][2][0][0][2] = 18,
+	[0][1][2][0][0][4] = 18,
+	[0][1][2][0][0][6] = 18,
+	[0][1][2][0][0][8] = 40,
+	[0][1][2][0][0][10] = 40,
+	[0][1][2][0][0][12] = 40,
+	[0][1][2][0][0][14] = 40,
+	[0][1][2][0][0][15] = 40,
+	[0][1][2][0][0][17] = 40,
+	[0][1][2][0][0][19] = 40,
+	[0][1][2][0][0][21] = 40,
+	[0][1][2][0][0][23] = 40,
+	[0][1][2][0][0][25] = 40,
+	[0][1][2][0][0][27] = 40,
+	[0][1][2][0][0][29] = 40,
+	[0][1][2][0][0][31] = 40,
+	[0][1][2][0][0][33] = 40,
+	[0][1][2][0][0][35] = 40,
+	[0][1][2][0][0][37] = 42,
+	[0][1][2][0][0][38] = 16,
+	[0][1][2][0][0][40] = 16,
+	[0][1][2][0][0][42] = 16,
+	[0][1][2][0][0][44] = 16,
+	[0][1][2][0][0][46] = 16,
+	[0][1][2][1][0][0] = 6,
+	[0][1][2][1][0][2] = 6,
+	[0][1][2][1][0][4] = 6,
+	[0][1][2][1][0][6] = 6,
+	[0][1][2][1][0][8] = 28,
+	[0][1][2][1][0][10] = 28,
+	[0][1][2][1][0][12] = 28,
+	[0][1][2][1][0][14] = 28,
+	[0][1][2][1][0][15] = 28,
+	[0][1][2][1][0][17] = 28,
+	[0][1][2][1][0][19] = 28,
+	[0][1][2][1][0][21] = 28,
+	[0][1][2][1][0][23] = 28,
+	[0][1][2][1][0][25] = 28,
+	[0][1][2][1][0][27] = 28,
+	[0][1][2][1][0][29] = 28,
+	[0][1][2][1][0][31] = 28,
+	[0][1][2][1][0][33] = 28,
+	[0][1][2][1][0][35] = 28,
+	[0][1][2][1][0][37] = 30,
+	[0][1][2][1][0][38] = 4,
+	[0][1][2][1][0][40] = 4,
+	[0][1][2][1][0][42] = 4,
+	[0][1][2][1][0][44] = 4,
+	[0][1][2][1][0][46] = 4,
+	[1][0][2][0][0][1] = 30,
+	[1][0][2][0][0][5] = 30,
+	[1][0][2][0][0][9] = 52,
+	[1][0][2][0][0][13] = 52,
+	[1][0][2][0][0][16] = 52,
+	[1][0][2][0][0][20] = 52,
+	[1][0][2][0][0][24] = 52,
+	[1][0][2][0][0][28] = 52,
+	[1][0][2][0][0][32] = 52,
+	[1][0][2][0][0][36] = 54,
+	[1][0][2][0][0][39] = 28,
+	[1][0][2][0][0][43] = 28,
+	[1][1][2][0][0][1] = 18,
+	[1][1][2][0][0][5] = 18,
+	[1][1][2][0][0][9] = 40,
+	[1][1][2][0][0][13] = 40,
+	[1][1][2][0][0][16] = 40,
+	[1][1][2][0][0][20] = 40,
+	[1][1][2][0][0][24] = 40,
+	[1][1][2][0][0][28] = 40,
+	[1][1][2][0][0][32] = 40,
+	[1][1][2][0][0][36] = 42,
+	[1][1][2][0][0][39] = 16,
+	[1][1][2][0][0][43] = 16,
+	[1][1][2][1][0][1] = 6,
+	[1][1][2][1][0][5] = 6,
+	[1][1][2][1][0][9] = 28,
+	[1][1][2][1][0][13] = 28,
+	[1][1][2][1][0][16] = 28,
+	[1][1][2][1][0][20] = 28,
+	[1][1][2][1][0][24] = 28,
+	[1][1][2][1][0][28] = 28,
+	[1][1][2][1][0][32] = 28,
+	[1][1][2][1][0][36] = 30,
+	[1][1][2][1][0][39] = 4,
+	[1][1][2][1][0][43] = 4,
+	[2][0][2][0][0][3] = 30,
+	[2][0][2][0][0][11] = 52,
+	[2][0][2][0][0][18] = 52,
+	[2][0][2][0][0][26] = 52,
+	[2][0][2][0][0][34] = 54,
+	[2][0][2][0][0][41] = 28,
+	[2][1][2][0][0][3] = 18,
+	[2][1][2][0][0][11] = 40,
+	[2][1][2][0][0][18] = 40,
+	[2][1][2][0][0][26] = 40,
+	[2][1][2][0][0][34] = 42,
+	[2][1][2][0][0][41] = 16,
+	[2][1][2][1][0][3] = 6,
+	[2][1][2][1][0][11] = 28,
+	[2][1][2][1][0][18] = 28,
+	[2][1][2][1][0][26] = 28,
+	[2][1][2][1][0][34] = 30,
+	[2][1][2][1][0][41] = 4,
+	[0][0][1][0][2][0] = 76,
+	[0][0][1][0][1][0] = 58,
+	[0][0][1][0][3][0] = 62,
+	[0][0][1][0][5][0] = 62,
+	[0][0][1][0][6][0] = 58,
+	[0][0][1][0][9][0] = 58,
+	[0][0][1][0][8][0] = 30,
+	[0][0][1][0][11][0] = 52,
+	[0][0][1][0][2][2] = 76,
+	[0][0][1][0][1][2] = 58,
+	[0][0][1][0][3][2] = 62,
+	[0][0][1][0][5][2] = 62,
+	[0][0][1][0][6][2] = 58,
+	[0][0][1][0][9][2] = 58,
+	[0][0][1][0][8][2] = 30,
+	[0][0][1][0][11][2] = 52,
+	[0][0][1][0][2][4] = 76,
+	[0][0][1][0][1][4] = 58,
+	[0][0][1][0][3][4] = 62,
+	[0][0][1][0][5][4] = 62,
+	[0][0][1][0][6][4] = 58,
+	[0][0][1][0][9][4] = 58,
+	[0][0][1][0][8][4] = 30,
+	[0][0][1][0][11][4] = 52,
+	[0][0][1][0][2][6] = 76,
+	[0][0][1][0][1][6] = 58,
+	[0][0][1][0][3][6] = 62,
+	[0][0][1][0][5][6] = 62,
+	[0][0][1][0][6][6] = 54,
+	[0][0][1][0][9][6] = 58,
+	[0][0][1][0][8][6] = 30,
+	[0][0][1][0][11][6] = 52,
+	[0][0][1][0][2][8] = 76,
+	[0][0][1][0][1][8] = 58,
+	[0][0][1][0][3][8] = 62,
+	[0][0][1][0][5][8] = 64,
+	[0][0][1][0][6][8] = 58,
+	[0][0][1][0][9][8] = 58,
+	[0][0][1][0][8][8] = 54,
+	[0][0][1][0][11][8] = 52,
+	[0][0][1][0][2][10] = 76,
+	[0][0][1][0][1][10] = 58,
+	[0][0][1][0][3][10] = 62,
+	[0][0][1][0][5][10] = 64,
+	[0][0][1][0][6][10] = 58,
+	[0][0][1][0][9][10] = 58,
+	[0][0][1][0][8][10] = 54,
+	[0][0][1][0][11][10] = 52,
+	[0][0][1][0][2][12] = 76,
+	[0][0][1][0][1][12] = 58,
+	[0][0][1][0][3][12] = 62,
+	[0][0][1][0][5][12] = 64,
+	[0][0][1][0][6][12] = 58,
+	[0][0][1][0][9][12] = 58,
+	[0][0][1][0][8][12] = 54,
+	[0][0][1][0][11][12] = 52,
+	[0][0][1][0][2][14] = 76,
+	[0][0][1][0][1][14] = 58,
+	[0][0][1][0][3][14] = 62,
+	[0][0][1][0][5][14] = 64,
+	[0][0][1][0][6][14] = 58,
+	[0][0][1][0][9][14] = 58,
+	[0][0][1][0][8][14] = 54,
+	[0][0][1][0][11][14] = 52,
+	[0][0][1][0][2][15] = 76,
+	[0][0][1][0][1][15] = 58,
+	[0][0][1][0][3][15] = 76,
+	[0][0][1][0][5][15] = 76,
+	[0][0][1][0][6][15] = 58,
+	[0][0][1][0][9][15] = 58,
+	[0][0][1][0][8][15] = 54,
+	[0][0][1][0][11][15] = 52,
+	[0][0][1][0][2][17] = 76,
+	[0][0][1][0][1][17] = 58,
+	[0][0][1][0][3][17] = 76,
+	[0][0][1][0][5][17] = 76,
+	[0][0][1][0][6][17] = 58,
+	[0][0][1][0][9][17] = 58,
+	[0][0][1][0][8][17] = 54,
+	[0][0][1][0][11][17] = 52,
+	[0][0][1][0][2][19] = 76,
+	[0][0][1][0][1][19] = 58,
+	[0][0][1][0][3][19] = 76,
+	[0][0][1][0][5][19] = 76,
+	[0][0][1][0][6][19] = 58,
+	[0][0][1][0][9][19] = 58,
+	[0][0][1][0][8][19] = 54,
+	[0][0][1][0][11][19] = 52,
+	[0][0][1][0][2][21] = 76,
+	[0][0][1][0][1][21] = 58,
+	[0][0][1][0][3][21] = 76,
+	[0][0][1][0][5][21] = 76,
+	[0][0][1][0][6][21] = 58,
+	[0][0][1][0][9][21] = 58,
+	[0][0][1][0][8][21] = 54,
+	[0][0][1][0][11][21] = 52,
+	[0][0][1][0][2][23] = 76,
+	[0][0][1][0][1][23] = 58,
+	[0][0][1][0][3][23] = 76,
+	[0][0][1][0][5][23] = 76,
+	[0][0][1][0][6][23] = 58,
+	[0][0][1][0][9][23] = 58,
+	[0][0][1][0][8][23] = 54,
+	[0][0][1][0][11][23] = 52,
+	[0][0][1][0][2][25] = 76,
+	[0][0][1][0][1][25] = 58,
+	[0][0][1][0][3][25] = 76,
+	[0][0][1][0][5][25] = 127,
+	[0][0][1][0][6][25] = 58,
+	[0][0][1][0][9][25] = 127,
+	[0][0][1][0][8][25] = 54,
+	[0][0][1][0][11][25] = 52,
+	[0][0][1][0][2][27] = 76,
+	[0][0][1][0][1][27] = 58,
+	[0][0][1][0][3][27] = 76,
+	[0][0][1][0][5][27] = 127,
+	[0][0][1][0][6][27] = 58,
+	[0][0][1][0][9][27] = 127,
+	[0][0][1][0][8][27] = 54,
+	[0][0][1][0][11][27] = 52,
+	[0][0][1][0][2][29] = 76,
+	[0][0][1][0][1][29] = 58,
+	[0][0][1][0][3][29] = 76,
+	[0][0][1][0][5][29] = 127,
+	[0][0][1][0][6][29] = 58,
+	[0][0][1][0][9][29] = 127,
+	[0][0][1][0][8][29] = 54,
+	[0][0][1][0][11][29] = 52,
+	[0][0][1][0][2][31] = 76,
+	[0][0][1][0][1][31] = 58,
+	[0][0][1][0][3][31] = 76,
+	[0][0][1][0][5][31] = 76,
+	[0][0][1][0][6][31] = 58,
+	[0][0][1][0][9][31] = 58,
+	[0][0][1][0][8][31] = 54,
+	[0][0][1][0][11][31] = 52,
+	[0][0][1][0][2][33] = 76,
+	[0][0][1][0][1][33] = 58,
+	[0][0][1][0][3][33] = 76,
+	[0][0][1][0][5][33] = 76,
+	[0][0][1][0][6][33] = 58,
+	[0][0][1][0][9][33] = 58,
+	[0][0][1][0][8][33] = 54,
+	[0][0][1][0][11][33] = 52,
+	[0][0][1][0][2][35] = 74,
+	[0][0][1][0][1][35] = 58,
+	[0][0][1][0][3][35] = 76,
+	[0][0][1][0][5][35] = 74,
+	[0][0][1][0][6][35] = 58,
+	[0][0][1][0][9][35] = 58,
+	[0][0][1][0][8][35] = 54,
+	[0][0][1][0][11][35] = 52,
+	[0][0][1][0][2][37] = 76,
+	[0][0][1][0][1][37] = 127,
+	[0][0][1][0][3][37] = 76,
+	[0][0][1][0][5][37] = 76,
+	[0][0][1][0][6][37] = 58,
+	[0][0][1][0][9][37] = 76,
+	[0][0][1][0][8][37] = 54,
+	[0][0][1][0][11][37] = 127,
+	[0][0][1][0][2][38] = 76,
+	[0][0][1][0][1][38] = 28,
+	[0][0][1][0][3][38] = 127,
+	[0][0][1][0][5][38] = 76,
+	[0][0][1][0][6][38] = 28,
+	[0][0][1][0][9][38] = 76,
+	[0][0][1][0][8][38] = 54,
+	[0][0][1][0][11][38] = 52,
+	[0][0][1][0][2][40] = 76,
+	[0][0][1][0][1][40] = 28,
+	[0][0][1][0][3][40] = 127,
+	[0][0][1][0][5][40] = 76,
+	[0][0][1][0][6][40] = 28,
+	[0][0][1][0][9][40] = 76,
+	[0][0][1][0][8][40] = 54,
+	[0][0][1][0][11][40] = 52,
+	[0][0][1][0][2][42] = 76,
+	[0][0][1][0][1][42] = 28,
+	[0][0][1][0][3][42] = 127,
+	[0][0][1][0][5][42] = 76,
+	[0][0][1][0][6][42] = 28,
+	[0][0][1][0][9][42] = 76,
+	[0][0][1][0][8][42] = 54,
+	[0][0][1][0][11][42] = 52,
+	[0][0][1][0][2][44] = 76,
+	[0][0][1][0][1][44] = 28,
+	[0][0][1][0][3][44] = 127,
+	[0][0][1][0][5][44] = 76,
+	[0][0][1][0][6][44] = 28,
+	[0][0][1][0][9][44] = 76,
+	[0][0][1][0][8][44] = 54,
+	[0][0][1][0][11][44] = 52,
+	[0][0][1][0][2][46] = 76,
+	[0][0][1][0][1][46] = 28,
+	[0][0][1][0][3][46] = 127,
+	[0][0][1][0][5][46] = 76,
+	[0][0][1][0][6][46] = 28,
+	[0][0][1][0][9][46] = 76,
+	[0][0][1][0][8][46] = 54,
+	[0][0][1][0][11][46] = 52,
+	[0][1][1][0][2][0] = 68,
+	[0][1][1][0][1][0] = 46,
+	[0][1][1][0][3][0] = 50,
+	[0][1][1][0][5][0] = 40,
+	[0][1][1][0][6][0] = 46,
+	[0][1][1][0][9][0] = 46,
+	[0][1][1][0][8][0] = 18,
+	[0][1][1][0][11][0] = 40,
+	[0][1][1][0][2][2] = 68,
+	[0][1][1][0][1][2] = 46,
+	[0][1][1][0][3][2] = 50,
+	[0][1][1][0][5][2] = 40,
+	[0][1][1][0][6][2] = 46,
+	[0][1][1][0][9][2] = 46,
+	[0][1][1][0][8][2] = 18,
+	[0][1][1][0][11][2] = 40,
+	[0][1][1][0][2][4] = 68,
+	[0][1][1][0][1][4] = 46,
+	[0][1][1][0][3][4] = 50,
+	[0][1][1][0][5][4] = 40,
+	[0][1][1][0][6][4] = 46,
+	[0][1][1][0][9][4] = 46,
+	[0][1][1][0][8][4] = 18,
+	[0][1][1][0][11][4] = 40,
+	[0][1][1][0][2][6] = 68,
+	[0][1][1][0][1][6] = 46,
+	[0][1][1][0][3][6] = 50,
+	[0][1][1][0][5][6] = 40,
+	[0][1][1][0][6][6] = 36,
+	[0][1][1][0][9][6] = 46,
+	[0][1][1][0][8][6] = 18,
+	[0][1][1][0][11][6] = 40,
+	[0][1][1][0][2][8] = 68,
+	[0][1][1][0][1][8] = 46,
+	[0][1][1][0][3][8] = 50,
+	[0][1][1][0][5][8] = 52,
+	[0][1][1][0][6][8] = 46,
+	[0][1][1][0][9][8] = 46,
+	[0][1][1][0][8][8] = 42,
+	[0][1][1][0][11][8] = 40,
+	[0][1][1][0][2][10] = 68,
+	[0][1][1][0][1][10] = 46,
+	[0][1][1][0][3][10] = 50,
+	[0][1][1][0][5][10] = 52,
+	[0][1][1][0][6][10] = 46,
+	[0][1][1][0][9][10] = 46,
+	[0][1][1][0][8][10] = 42,
+	[0][1][1][0][11][10] = 40,
+	[0][1][1][0][2][12] = 68,
+	[0][1][1][0][1][12] = 46,
+	[0][1][1][0][3][12] = 50,
+	[0][1][1][0][5][12] = 52,
+	[0][1][1][0][6][12] = 46,
+	[0][1][1][0][9][12] = 46,
+	[0][1][1][0][8][12] = 42,
+	[0][1][1][0][11][12] = 40,
+	[0][1][1][0][2][14] = 68,
+	[0][1][1][0][1][14] = 46,
+	[0][1][1][0][3][14] = 50,
+	[0][1][1][0][5][14] = 52,
+	[0][1][1][0][6][14] = 46,
+	[0][1][1][0][9][14] = 46,
+	[0][1][1][0][8][14] = 42,
+	[0][1][1][0][11][14] = 40,
+	[0][1][1][0][2][15] = 68,
+	[0][1][1][0][1][15] = 46,
+	[0][1][1][0][3][15] = 70,
+	[0][1][1][0][5][15] = 68,
+	[0][1][1][0][6][15] = 46,
+	[0][1][1][0][9][15] = 46,
+	[0][1][1][0][8][15] = 42,
+	[0][1][1][0][11][15] = 40,
+	[0][1][1][0][2][17] = 68,
+	[0][1][1][0][1][17] = 46,
+	[0][1][1][0][3][17] = 70,
+	[0][1][1][0][5][17] = 68,
+	[0][1][1][0][6][17] = 46,
+	[0][1][1][0][9][17] = 46,
+	[0][1][1][0][8][17] = 42,
+	[0][1][1][0][11][17] = 40,
+	[0][1][1][0][2][19] = 68,
+	[0][1][1][0][1][19] = 46,
+	[0][1][1][0][3][19] = 70,
+	[0][1][1][0][5][19] = 68,
+	[0][1][1][0][6][19] = 46,
+	[0][1][1][0][9][19] = 46,
+	[0][1][1][0][8][19] = 42,
+	[0][1][1][0][11][19] = 40,
+	[0][1][1][0][2][21] = 68,
+	[0][1][1][0][1][21] = 46,
+	[0][1][1][0][3][21] = 70,
+	[0][1][1][0][5][21] = 68,
+	[0][1][1][0][6][21] = 46,
+	[0][1][1][0][9][21] = 46,
+	[0][1][1][0][8][21] = 42,
+	[0][1][1][0][11][21] = 40,
+	[0][1][1][0][2][23] = 68,
+	[0][1][1][0][1][23] = 46,
+	[0][1][1][0][3][23] = 70,
+	[0][1][1][0][5][23] = 68,
+	[0][1][1][0][6][23] = 46,
+	[0][1][1][0][9][23] = 46,
+	[0][1][1][0][8][23] = 42,
+	[0][1][1][0][11][23] = 40,
+	[0][1][1][0][2][25] = 68,
+	[0][1][1][0][1][25] = 46,
+	[0][1][1][0][3][25] = 70,
+	[0][1][1][0][5][25] = 127,
+	[0][1][1][0][6][25] = 46,
+	[0][1][1][0][9][25] = 127,
+	[0][1][1][0][8][25] = 42,
+	[0][1][1][0][11][25] = 40,
+	[0][1][1][0][2][27] = 68,
+	[0][1][1][0][1][27] = 46,
+	[0][1][1][0][3][27] = 70,
+	[0][1][1][0][5][27] = 127,
+	[0][1][1][0][6][27] = 46,
+	[0][1][1][0][9][27] = 127,
+	[0][1][1][0][8][27] = 42,
+	[0][1][1][0][11][27] = 40,
+	[0][1][1][0][2][29] = 68,
+	[0][1][1][0][1][29] = 46,
+	[0][1][1][0][3][29] = 70,
+	[0][1][1][0][5][29] = 127,
+	[0][1][1][0][6][29] = 46,
+	[0][1][1][0][9][29] = 127,
+	[0][1][1][0][8][29] = 42,
+	[0][1][1][0][11][29] = 40,
+	[0][1][1][0][2][31] = 68,
+	[0][1][1][0][1][31] = 46,
+	[0][1][1][0][3][31] = 70,
+	[0][1][1][0][5][31] = 68,
+	[0][1][1][0][6][31] = 46,
+	[0][1][1][0][9][31] = 46,
+	[0][1][1][0][8][31] = 42,
+	[0][1][1][0][11][31] = 40,
+	[0][1][1][0][2][33] = 68,
+	[0][1][1][0][1][33] = 46,
+	[0][1][1][0][3][33] = 70,
+	[0][1][1][0][5][33] = 68,
+	[0][1][1][0][6][33] = 46,
+	[0][1][1][0][9][33] = 46,
+	[0][1][1][0][8][33] = 42,
+	[0][1][1][0][11][33] = 40,
+	[0][1][1][0][2][35] = 66,
+	[0][1][1][0][1][35] = 46,
+	[0][1][1][0][3][35] = 70,
+	[0][1][1][0][5][35] = 66,
+	[0][1][1][0][6][35] = 46,
+	[0][1][1][0][9][35] = 46,
+	[0][1][1][0][8][35] = 42,
+	[0][1][1][0][11][35] = 40,
+	[0][1][1][0][2][37] = 68,
+	[0][1][1][0][1][37] = 127,
+	[0][1][1][0][3][37] = 70,
+	[0][1][1][0][5][37] = 68,
+	[0][1][1][0][6][37] = 46,
+	[0][1][1][0][9][37] = 68,
+	[0][1][1][0][8][37] = 42,
+	[0][1][1][0][11][37] = 127,
+	[0][1][1][0][2][38] = 76,
+	[0][1][1][0][1][38] = 16,
+	[0][1][1][0][3][38] = 127,
+	[0][1][1][0][5][38] = 76,
+	[0][1][1][0][6][38] = 16,
+	[0][1][1][0][9][38] = 76,
+	[0][1][1][0][8][38] = 42,
+	[0][1][1][0][11][38] = 40,
+	[0][1][1][0][2][40] = 76,
+	[0][1][1][0][1][40] = 16,
+	[0][1][1][0][3][40] = 127,
+	[0][1][1][0][5][40] = 76,
+	[0][1][1][0][6][40] = 16,
+	[0][1][1][0][9][40] = 76,
+	[0][1][1][0][8][40] = 42,
+	[0][1][1][0][11][40] = 40,
+	[0][1][1][0][2][42] = 76,
+	[0][1][1][0][1][42] = 16,
+	[0][1][1][0][3][42] = 127,
+	[0][1][1][0][5][42] = 76,
+	[0][1][1][0][6][42] = 16,
+	[0][1][1][0][9][42] = 76,
+	[0][1][1][0][8][42] = 42,
+	[0][1][1][0][11][42] = 40,
+	[0][1][1][0][2][44] = 76,
+	[0][1][1][0][1][44] = 16,
+	[0][1][1][0][3][44] = 127,
+	[0][1][1][0][5][44] = 76,
+	[0][1][1][0][6][44] = 16,
+	[0][1][1][0][9][44] = 76,
+	[0][1][1][0][8][44] = 42,
+	[0][1][1][0][11][44] = 40,
+	[0][1][1][0][2][46] = 76,
+	[0][1][1][0][1][46] = 16,
+	[0][1][1][0][3][46] = 127,
+	[0][1][1][0][5][46] = 76,
+	[0][1][1][0][6][46] = 16,
+	[0][1][1][0][9][46] = 76,
+	[0][1][1][0][8][46] = 42,
+	[0][1][1][0][11][46] = 40,
+	[0][0][2][0][2][0] = 76,
+	[0][0][2][0][1][0] = 58,
+	[0][0][2][0][3][0] = 62,
+	[0][0][2][0][5][0] = 62,
+	[0][0][2][0][6][0] = 58,
+	[0][0][2][0][9][0] = 58,
+	[0][0][2][0][8][0] = 30,
+	[0][0][2][0][11][0] = 52,
+	[0][0][2][0][2][2] = 76,
+	[0][0][2][0][1][2] = 58,
+	[0][0][2][0][3][2] = 62,
+	[0][0][2][0][5][2] = 62,
+	[0][0][2][0][6][2] = 58,
+	[0][0][2][0][9][2] = 58,
+	[0][0][2][0][8][2] = 30,
+	[0][0][2][0][11][2] = 52,
+	[0][0][2][0][2][4] = 76,
+	[0][0][2][0][1][4] = 58,
+	[0][0][2][0][3][4] = 62,
+	[0][0][2][0][5][4] = 62,
+	[0][0][2][0][6][4] = 58,
+	[0][0][2][0][9][4] = 58,
+	[0][0][2][0][8][4] = 30,
+	[0][0][2][0][11][4] = 52,
+	[0][0][2][0][2][6] = 76,
+	[0][0][2][0][1][6] = 58,
+	[0][0][2][0][3][6] = 62,
+	[0][0][2][0][5][6] = 62,
+	[0][0][2][0][6][6] = 54,
+	[0][0][2][0][9][6] = 58,
+	[0][0][2][0][8][6] = 30,
+	[0][0][2][0][11][6] = 52,
+	[0][0][2][0][2][8] = 76,
+	[0][0][2][0][1][8] = 58,
+	[0][0][2][0][3][8] = 62,
+	[0][0][2][0][5][8] = 64,
+	[0][0][2][0][6][8] = 58,
+	[0][0][2][0][9][8] = 58,
+	[0][0][2][0][8][8] = 54,
+	[0][0][2][0][11][8] = 52,
+	[0][0][2][0][2][10] = 76,
+	[0][0][2][0][1][10] = 58,
+	[0][0][2][0][3][10] = 62,
+	[0][0][2][0][5][10] = 64,
+	[0][0][2][0][6][10] = 58,
+	[0][0][2][0][9][10] = 58,
+	[0][0][2][0][8][10] = 54,
+	[0][0][2][0][11][10] = 52,
+	[0][0][2][0][2][12] = 76,
+	[0][0][2][0][1][12] = 58,
+	[0][0][2][0][3][12] = 62,
+	[0][0][2][0][5][12] = 64,
+	[0][0][2][0][6][12] = 58,
+	[0][0][2][0][9][12] = 58,
+	[0][0][2][0][8][12] = 54,
+	[0][0][2][0][11][12] = 52,
+	[0][0][2][0][2][14] = 76,
+	[0][0][2][0][1][14] = 58,
+	[0][0][2][0][3][14] = 62,
+	[0][0][2][0][5][14] = 64,
+	[0][0][2][0][6][14] = 58,
+	[0][0][2][0][9][14] = 58,
+	[0][0][2][0][8][14] = 54,
+	[0][0][2][0][11][14] = 52,
+	[0][0][2][0][2][15] = 74,
+	[0][0][2][0][1][15] = 58,
+	[0][0][2][0][3][15] = 76,
+	[0][0][2][0][5][15] = 74,
+	[0][0][2][0][6][15] = 58,
+	[0][0][2][0][9][15] = 58,
+	[0][0][2][0][8][15] = 54,
+	[0][0][2][0][11][15] = 52,
+	[0][0][2][0][2][17] = 76,
+	[0][0][2][0][1][17] = 58,
+	[0][0][2][0][3][17] = 76,
+	[0][0][2][0][5][17] = 76,
+	[0][0][2][0][6][17] = 58,
+	[0][0][2][0][9][17] = 58,
+	[0][0][2][0][8][17] = 54,
+	[0][0][2][0][11][17] = 52,
+	[0][0][2][0][2][19] = 76,
+	[0][0][2][0][1][19] = 58,
+	[0][0][2][0][3][19] = 76,
+	[0][0][2][0][5][19] = 76,
+	[0][0][2][0][6][19] = 58,
+	[0][0][2][0][9][19] = 58,
+	[0][0][2][0][8][19] = 54,
+	[0][0][2][0][11][19] = 52,
+	[0][0][2][0][2][21] = 76,
+	[0][0][2][0][1][21] = 58,
+	[0][0][2][0][3][21] = 76,
+	[0][0][2][0][5][21] = 76,
+	[0][0][2][0][6][21] = 58,
+	[0][0][2][0][9][21] = 58,
+	[0][0][2][0][8][21] = 54,
+	[0][0][2][0][11][21] = 52,
+	[0][0][2][0][2][23] = 76,
+	[0][0][2][0][1][23] = 58,
+	[0][0][2][0][3][23] = 76,
+	[0][0][2][0][5][23] = 76,
+	[0][0][2][0][6][23] = 58,
+	[0][0][2][0][9][23] = 58,
+	[0][0][2][0][8][23] = 54,
+	[0][0][2][0][11][23] = 52,
+	[0][0][2][0][2][25] = 76,
+	[0][0][2][0][1][25] = 58,
+	[0][0][2][0][3][25] = 76,
+	[0][0][2][0][5][25] = 127,
+	[0][0][2][0][6][25] = 58,
+	[0][0][2][0][9][25] = 127,
+	[0][0][2][0][8][25] = 54,
+	[0][0][2][0][11][25] = 52,
+	[0][0][2][0][2][27] = 76,
+	[0][0][2][0][1][27] = 58,
+	[0][0][2][0][3][27] = 76,
+	[0][0][2][0][5][27] = 127,
+	[0][0][2][0][6][27] = 58,
+	[0][0][2][0][9][27] = 127,
+	[0][0][2][0][8][27] = 54,
+	[0][0][2][0][11][27] = 52,
+	[0][0][2][0][2][29] = 76,
+	[0][0][2][0][1][29] = 58,
+	[0][0][2][0][3][29] = 76,
+	[0][0][2][0][5][29] = 127,
+	[0][0][2][0][6][29] = 58,
+	[0][0][2][0][9][29] = 127,
+	[0][0][2][0][8][29] = 54,
+	[0][0][2][0][11][29] = 52,
+	[0][0][2][0][2][31] = 76,
+	[0][0][2][0][1][31] = 58,
+	[0][0][2][0][3][31] = 76,
+	[0][0][2][0][5][31] = 76,
+	[0][0][2][0][6][31] = 58,
+	[0][0][2][0][9][31] = 58,
+	[0][0][2][0][8][31] = 54,
+	[0][0][2][0][11][31] = 52,
+	[0][0][2][0][2][33] = 76,
+	[0][0][2][0][1][33] = 58,
+	[0][0][2][0][3][33] = 76,
+	[0][0][2][0][5][33] = 76,
+	[0][0][2][0][6][33] = 58,
+	[0][0][2][0][9][33] = 58,
+	[0][0][2][0][8][33] = 54,
+	[0][0][2][0][11][33] = 52,
+	[0][0][2][0][2][35] = 70,
+	[0][0][2][0][1][35] = 58,
+	[0][0][2][0][3][35] = 76,
+	[0][0][2][0][5][35] = 70,
+	[0][0][2][0][6][35] = 58,
+	[0][0][2][0][9][35] = 58,
+	[0][0][2][0][8][35] = 54,
+	[0][0][2][0][11][35] = 52,
+	[0][0][2][0][2][37] = 76,
+	[0][0][2][0][1][37] = 127,
+	[0][0][2][0][3][37] = 76,
+	[0][0][2][0][5][37] = 76,
+	[0][0][2][0][6][37] = 58,
+	[0][0][2][0][9][37] = 76,
+	[0][0][2][0][8][37] = 54,
+	[0][0][2][0][11][37] = 127,
+	[0][0][2][0][2][38] = 76,
+	[0][0][2][0][1][38] = 28,
+	[0][0][2][0][3][38] = 127,
+	[0][0][2][0][5][38] = 76,
+	[0][0][2][0][6][38] = 28,
+	[0][0][2][0][9][38] = 76,
+	[0][0][2][0][8][38] = 54,
+	[0][0][2][0][11][38] = 52,
+	[0][0][2][0][2][40] = 76,
+	[0][0][2][0][1][40] = 28,
+	[0][0][2][0][3][40] = 127,
+	[0][0][2][0][5][40] = 76,
+	[0][0][2][0][6][40] = 28,
+	[0][0][2][0][9][40] = 76,
+	[0][0][2][0][8][40] = 54,
+	[0][0][2][0][11][40] = 52,
+	[0][0][2][0][2][42] = 76,
+	[0][0][2][0][1][42] = 28,
+	[0][0][2][0][3][42] = 127,
+	[0][0][2][0][5][42] = 76,
+	[0][0][2][0][6][42] = 28,
+	[0][0][2][0][9][42] = 76,
+	[0][0][2][0][8][42] = 54,
+	[0][0][2][0][11][42] = 52,
+	[0][0][2][0][2][44] = 76,
+	[0][0][2][0][1][44] = 28,
+	[0][0][2][0][3][44] = 127,
+	[0][0][2][0][5][44] = 76,
+	[0][0][2][0][6][44] = 28,
+	[0][0][2][0][9][44] = 76,
+	[0][0][2][0][8][44] = 54,
+	[0][0][2][0][11][44] = 52,
+	[0][0][2][0][2][46] = 76,
+	[0][0][2][0][1][46] = 28,
+	[0][0][2][0][3][46] = 127,
+	[0][0][2][0][5][46] = 76,
+	[0][0][2][0][6][46] = 28,
+	[0][0][2][0][9][46] = 76,
+	[0][0][2][0][8][46] = 54,
+	[0][0][2][0][11][46] = 52,
+	[0][1][2][0][2][0] = 68,
+	[0][1][2][0][1][0] = 46,
+	[0][1][2][0][3][0] = 50,
+	[0][1][2][0][5][0] = 40,
+	[0][1][2][0][6][0] = 46,
+	[0][1][2][0][9][0] = 46,
+	[0][1][2][0][8][0] = 18,
+	[0][1][2][0][11][0] = 40,
+	[0][1][2][0][2][2] = 68,
+	[0][1][2][0][1][2] = 46,
+	[0][1][2][0][3][2] = 50,
+	[0][1][2][0][5][2] = 40,
+	[0][1][2][0][6][2] = 46,
+	[0][1][2][0][9][2] = 46,
+	[0][1][2][0][8][2] = 18,
+	[0][1][2][0][11][2] = 40,
+	[0][1][2][0][2][4] = 68,
+	[0][1][2][0][1][4] = 46,
+	[0][1][2][0][3][4] = 50,
+	[0][1][2][0][5][4] = 40,
+	[0][1][2][0][6][4] = 46,
+	[0][1][2][0][9][4] = 46,
+	[0][1][2][0][8][4] = 18,
+	[0][1][2][0][11][4] = 40,
+	[0][1][2][0][2][6] = 68,
+	[0][1][2][0][1][6] = 46,
+	[0][1][2][0][3][6] = 50,
+	[0][1][2][0][5][6] = 40,
+	[0][1][2][0][6][6] = 36,
+	[0][1][2][0][9][6] = 46,
+	[0][1][2][0][8][6] = 18,
+	[0][1][2][0][11][6] = 40,
+	[0][1][2][0][2][8] = 68,
+	[0][1][2][0][1][8] = 46,
+	[0][1][2][0][3][8] = 50,
+	[0][1][2][0][5][8] = 52,
+	[0][1][2][0][6][8] = 46,
+	[0][1][2][0][9][8] = 46,
+	[0][1][2][0][8][8] = 42,
+	[0][1][2][0][11][8] = 40,
+	[0][1][2][0][2][10] = 68,
+	[0][1][2][0][1][10] = 46,
+	[0][1][2][0][3][10] = 50,
+	[0][1][2][0][5][10] = 52,
+	[0][1][2][0][6][10] = 46,
+	[0][1][2][0][9][10] = 46,
+	[0][1][2][0][8][10] = 42,
+	[0][1][2][0][11][10] = 40,
+	[0][1][2][0][2][12] = 68,
+	[0][1][2][0][1][12] = 46,
+	[0][1][2][0][3][12] = 50,
+	[0][1][2][0][5][12] = 52,
+	[0][1][2][0][6][12] = 46,
+	[0][1][2][0][9][12] = 46,
+	[0][1][2][0][8][12] = 42,
+	[0][1][2][0][11][12] = 40,
+	[0][1][2][0][2][14] = 68,
+	[0][1][2][0][1][14] = 46,
+	[0][1][2][0][3][14] = 50,
+	[0][1][2][0][5][14] = 52,
+	[0][1][2][0][6][14] = 46,
+	[0][1][2][0][9][14] = 46,
+	[0][1][2][0][8][14] = 42,
+	[0][1][2][0][11][14] = 40,
+	[0][1][2][0][2][15] = 68,
+	[0][1][2][0][1][15] = 46,
+	[0][1][2][0][3][15] = 70,
+	[0][1][2][0][5][15] = 68,
+	[0][1][2][0][6][15] = 46,
+	[0][1][2][0][9][15] = 46,
+	[0][1][2][0][8][15] = 42,
+	[0][1][2][0][11][15] = 40,
+	[0][1][2][0][2][17] = 68,
+	[0][1][2][0][1][17] = 46,
+	[0][1][2][0][3][17] = 70,
+	[0][1][2][0][5][17] = 68,
+	[0][1][2][0][6][17] = 46,
+	[0][1][2][0][9][17] = 46,
+	[0][1][2][0][8][17] = 42,
+	[0][1][2][0][11][17] = 40,
+	[0][1][2][0][2][19] = 68,
+	[0][1][2][0][1][19] = 46,
+	[0][1][2][0][3][19] = 70,
+	[0][1][2][0][5][19] = 68,
+	[0][1][2][0][6][19] = 46,
+	[0][1][2][0][9][19] = 46,
+	[0][1][2][0][8][19] = 42,
+	[0][1][2][0][11][19] = 40,
+	[0][1][2][0][2][21] = 68,
+	[0][1][2][0][1][21] = 46,
+	[0][1][2][0][3][21] = 70,
+	[0][1][2][0][5][21] = 68,
+	[0][1][2][0][6][21] = 46,
+	[0][1][2][0][9][21] = 46,
+	[0][1][2][0][8][21] = 42,
+	[0][1][2][0][11][21] = 40,
+	[0][1][2][0][2][23] = 68,
+	[0][1][2][0][1][23] = 46,
+	[0][1][2][0][3][23] = 70,
+	[0][1][2][0][5][23] = 68,
+	[0][1][2][0][6][23] = 46,
+	[0][1][2][0][9][23] = 46,
+	[0][1][2][0][8][23] = 42,
+	[0][1][2][0][11][23] = 40,
+	[0][1][2][0][2][25] = 68,
+	[0][1][2][0][1][25] = 46,
+	[0][1][2][0][3][25] = 70,
+	[0][1][2][0][5][25] = 127,
+	[0][1][2][0][6][25] = 46,
+	[0][1][2][0][9][25] = 127,
+	[0][1][2][0][8][25] = 42,
+	[0][1][2][0][11][25] = 40,
+	[0][1][2][0][2][27] = 68,
+	[0][1][2][0][1][27] = 46,
+	[0][1][2][0][3][27] = 70,
+	[0][1][2][0][5][27] = 127,
+	[0][1][2][0][6][27] = 46,
+	[0][1][2][0][9][27] = 127,
+	[0][1][2][0][8][27] = 42,
+	[0][1][2][0][11][27] = 40,
+	[0][1][2][0][2][29] = 68,
+	[0][1][2][0][1][29] = 46,
+	[0][1][2][0][3][29] = 70,
+	[0][1][2][0][5][29] = 127,
+	[0][1][2][0][6][29] = 46,
+	[0][1][2][0][9][29] = 127,
+	[0][1][2][0][8][29] = 42,
+	[0][1][2][0][11][29] = 40,
+	[0][1][2][0][2][31] = 68,
+	[0][1][2][0][1][31] = 46,
+	[0][1][2][0][3][31] = 70,
+	[0][1][2][0][5][31] = 68,
+	[0][1][2][0][6][31] = 46,
+	[0][1][2][0][9][31] = 46,
+	[0][1][2][0][8][31] = 42,
+	[0][1][2][0][11][31] = 40,
+	[0][1][2][0][2][33] = 68,
+	[0][1][2][0][1][33] = 46,
+	[0][1][2][0][3][33] = 70,
+	[0][1][2][0][5][33] = 68,
+	[0][1][2][0][6][33] = 46,
+	[0][1][2][0][9][33] = 46,
+	[0][1][2][0][8][33] = 42,
+	[0][1][2][0][11][33] = 40,
+	[0][1][2][0][2][35] = 64,
+	[0][1][2][0][1][35] = 46,
+	[0][1][2][0][3][35] = 70,
+	[0][1][2][0][5][35] = 64,
+	[0][1][2][0][6][35] = 46,
+	[0][1][2][0][9][35] = 46,
+	[0][1][2][0][8][35] = 42,
+	[0][1][2][0][11][35] = 40,
+	[0][1][2][0][2][37] = 68,
+	[0][1][2][0][1][37] = 127,
+	[0][1][2][0][3][37] = 70,
+	[0][1][2][0][5][37] = 68,
+	[0][1][2][0][6][37] = 46,
+	[0][1][2][0][9][37] = 68,
+	[0][1][2][0][8][37] = 42,
+	[0][1][2][0][11][37] = 127,
+	[0][1][2][0][2][38] = 76,
+	[0][1][2][0][1][38] = 16,
+	[0][1][2][0][3][38] = 127,
+	[0][1][2][0][5][38] = 76,
+	[0][1][2][0][6][38] = 16,
+	[0][1][2][0][9][38] = 76,
+	[0][1][2][0][8][38] = 42,
+	[0][1][2][0][11][38] = 40,
+	[0][1][2][0][2][40] = 76,
+	[0][1][2][0][1][40] = 16,
+	[0][1][2][0][3][40] = 127,
+	[0][1][2][0][5][40] = 76,
+	[0][1][2][0][6][40] = 16,
+	[0][1][2][0][9][40] = 76,
+	[0][1][2][0][8][40] = 42,
+	[0][1][2][0][11][40] = 40,
+	[0][1][2][0][2][42] = 76,
+	[0][1][2][0][1][42] = 16,
+	[0][1][2][0][3][42] = 127,
+	[0][1][2][0][5][42] = 76,
+	[0][1][2][0][6][42] = 16,
+	[0][1][2][0][9][42] = 76,
+	[0][1][2][0][8][42] = 42,
+	[0][1][2][0][11][42] = 40,
+	[0][1][2][0][2][44] = 76,
+	[0][1][2][0][1][44] = 16,
+	[0][1][2][0][3][44] = 127,
+	[0][1][2][0][5][44] = 76,
+	[0][1][2][0][6][44] = 16,
+	[0][1][2][0][9][44] = 76,
+	[0][1][2][0][8][44] = 42,
+	[0][1][2][0][11][44] = 40,
+	[0][1][2][0][2][46] = 76,
+	[0][1][2][0][1][46] = 16,
+	[0][1][2][0][3][46] = 127,
+	[0][1][2][0][5][46] = 76,
+	[0][1][2][0][6][46] = 16,
+	[0][1][2][0][9][46] = 76,
+	[0][1][2][0][8][46] = 42,
+	[0][1][2][0][11][46] = 40,
+	[0][1][2][1][2][0] = 68,
+	[0][1][2][1][1][0] = 34,
+	[0][1][2][1][3][0] = 50,
+	[0][1][2][1][5][0] = 38,
+	[0][1][2][1][6][0] = 34,
+	[0][1][2][1][9][0] = 34,
+	[0][1][2][1][8][0] = 6,
+	[0][1][2][1][11][0] = 28,
+	[0][1][2][1][2][2] = 68,
+	[0][1][2][1][1][2] = 34,
+	[0][1][2][1][3][2] = 50,
+	[0][1][2][1][5][2] = 38,
+	[0][1][2][1][6][2] = 34,
+	[0][1][2][1][9][2] = 34,
+	[0][1][2][1][8][2] = 6,
+	[0][1][2][1][11][2] = 28,
+	[0][1][2][1][2][4] = 68,
+	[0][1][2][1][1][4] = 34,
+	[0][1][2][1][3][4] = 50,
+	[0][1][2][1][5][4] = 38,
+	[0][1][2][1][6][4] = 34,
+	[0][1][2][1][9][4] = 34,
+	[0][1][2][1][8][4] = 6,
+	[0][1][2][1][11][4] = 28,
+	[0][1][2][1][2][6] = 68,
+	[0][1][2][1][1][6] = 34,
+	[0][1][2][1][3][6] = 50,
+	[0][1][2][1][5][6] = 38,
+	[0][1][2][1][6][6] = 34,
+	[0][1][2][1][9][6] = 34,
+	[0][1][2][1][8][6] = 6,
+	[0][1][2][1][11][6] = 28,
+	[0][1][2][1][2][8] = 68,
+	[0][1][2][1][1][8] = 34,
+	[0][1][2][1][3][8] = 50,
+	[0][1][2][1][5][8] = 38,
+	[0][1][2][1][6][8] = 34,
+	[0][1][2][1][9][8] = 34,
+	[0][1][2][1][8][8] = 30,
+	[0][1][2][1][11][8] = 28,
+	[0][1][2][1][2][10] = 68,
+	[0][1][2][1][1][10] = 34,
+	[0][1][2][1][3][10] = 50,
+	[0][1][2][1][5][10] = 38,
+	[0][1][2][1][6][10] = 34,
+	[0][1][2][1][9][10] = 34,
+	[0][1][2][1][8][10] = 30,
+	[0][1][2][1][11][10] = 28,
+	[0][1][2][1][2][12] = 68,
+	[0][1][2][1][1][12] = 34,
+	[0][1][2][1][3][12] = 50,
+	[0][1][2][1][5][12] = 38,
+	[0][1][2][1][6][12] = 34,
+	[0][1][2][1][9][12] = 34,
+	[0][1][2][1][8][12] = 30,
+	[0][1][2][1][11][12] = 28,
+	[0][1][2][1][2][14] = 68,
+	[0][1][2][1][1][14] = 34,
+	[0][1][2][1][3][14] = 50,
+	[0][1][2][1][5][14] = 38,
+	[0][1][2][1][6][14] = 34,
+	[0][1][2][1][9][14] = 34,
+	[0][1][2][1][8][14] = 30,
+	[0][1][2][1][11][14] = 28,
+	[0][1][2][1][2][15] = 68,
+	[0][1][2][1][1][15] = 34,
+	[0][1][2][1][3][15] = 70,
+	[0][1][2][1][5][15] = 62,
+	[0][1][2][1][6][15] = 34,
+	[0][1][2][1][9][15] = 34,
+	[0][1][2][1][8][15] = 30,
+	[0][1][2][1][11][15] = 28,
+	[0][1][2][1][2][17] = 68,
+	[0][1][2][1][1][17] = 34,
+	[0][1][2][1][3][17] = 70,
+	[0][1][2][1][5][17] = 62,
+	[0][1][2][1][6][17] = 34,
+	[0][1][2][1][9][17] = 34,
+	[0][1][2][1][8][17] = 30,
+	[0][1][2][1][11][17] = 28,
+	[0][1][2][1][2][19] = 68,
+	[0][1][2][1][1][19] = 34,
+	[0][1][2][1][3][19] = 70,
+	[0][1][2][1][5][19] = 62,
+	[0][1][2][1][6][19] = 34,
+	[0][1][2][1][9][19] = 34,
+	[0][1][2][1][8][19] = 30,
+	[0][1][2][1][11][19] = 28,
+	[0][1][2][1][2][21] = 68,
+	[0][1][2][1][1][21] = 34,
+	[0][1][2][1][3][21] = 70,
+	[0][1][2][1][5][21] = 62,
+	[0][1][2][1][6][21] = 34,
+	[0][1][2][1][9][21] = 34,
+	[0][1][2][1][8][21] = 30,
+	[0][1][2][1][11][21] = 28,
+	[0][1][2][1][2][23] = 68,
+	[0][1][2][1][1][23] = 34,
+	[0][1][2][1][3][23] = 70,
+	[0][1][2][1][5][23] = 62,
+	[0][1][2][1][6][23] = 34,
+	[0][1][2][1][9][23] = 34,
+	[0][1][2][1][8][23] = 30,
+	[0][1][2][1][11][23] = 28,
+	[0][1][2][1][2][25] = 68,
+	[0][1][2][1][1][25] = 34,
+	[0][1][2][1][3][25] = 70,
+	[0][1][2][1][5][25] = 127,
+	[0][1][2][1][6][25] = 34,
+	[0][1][2][1][9][25] = 127,
+	[0][1][2][1][8][25] = 30,
+	[0][1][2][1][11][25] = 28,
+	[0][1][2][1][2][27] = 68,
+	[0][1][2][1][1][27] = 34,
+	[0][1][2][1][3][27] = 70,
+	[0][1][2][1][5][27] = 127,
+	[0][1][2][1][6][27] = 34,
+	[0][1][2][1][9][27] = 127,
+	[0][1][2][1][8][27] = 30,
+	[0][1][2][1][11][27] = 28,
+	[0][1][2][1][2][29] = 68,
+	[0][1][2][1][1][29] = 34,
+	[0][1][2][1][3][29] = 70,
+	[0][1][2][1][5][29] = 127,
+	[0][1][2][1][6][29] = 34,
+	[0][1][2][1][9][29] = 127,
+	[0][1][2][1][8][29] = 30,
+	[0][1][2][1][11][29] = 28,
+	[0][1][2][1][2][31] = 68,
+	[0][1][2][1][1][31] = 34,
+	[0][1][2][1][3][31] = 70,
+	[0][1][2][1][5][31] = 62,
+	[0][1][2][1][6][31] = 34,
+	[0][1][2][1][9][31] = 34,
+	[0][1][2][1][8][31] = 30,
+	[0][1][2][1][11][31] = 28,
+	[0][1][2][1][2][33] = 68,
+	[0][1][2][1][1][33] = 34,
+	[0][1][2][1][3][33] = 70,
+	[0][1][2][1][5][33] = 62,
+	[0][1][2][1][6][33] = 34,
+	[0][1][2][1][9][33] = 34,
+	[0][1][2][1][8][33] = 30,
+	[0][1][2][1][11][33] = 28,
+	[0][1][2][1][2][35] = 64,
+	[0][1][2][1][1][35] = 34,
+	[0][1][2][1][3][35] = 70,
+	[0][1][2][1][5][35] = 62,
+	[0][1][2][1][6][35] = 34,
+	[0][1][2][1][9][35] = 34,
+	[0][1][2][1][8][35] = 30,
+	[0][1][2][1][11][35] = 28,
+	[0][1][2][1][2][37] = 68,
+	[0][1][2][1][1][37] = 127,
+	[0][1][2][1][3][37] = 70,
+	[0][1][2][1][5][37] = 62,
+	[0][1][2][1][6][37] = 34,
+	[0][1][2][1][9][37] = 68,
+	[0][1][2][1][8][37] = 30,
+	[0][1][2][1][11][37] = 127,
+	[0][1][2][1][2][38] = 76,
+	[0][1][2][1][1][38] = 4,
+	[0][1][2][1][3][38] = 127,
+	[0][1][2][1][5][38] = 76,
+	[0][1][2][1][6][38] = 4,
+	[0][1][2][1][9][38] = 76,
+	[0][1][2][1][8][38] = 30,
+	[0][1][2][1][11][38] = 28,
+	[0][1][2][1][2][40] = 76,
+	[0][1][2][1][1][40] = 4,
+	[0][1][2][1][3][40] = 127,
+	[0][1][2][1][5][40] = 76,
+	[0][1][2][1][6][40] = 4,
+	[0][1][2][1][9][40] = 76,
+	[0][1][2][1][8][40] = 30,
+	[0][1][2][1][11][40] = 28,
+	[0][1][2][1][2][42] = 76,
+	[0][1][2][1][1][42] = 4,
+	[0][1][2][1][3][42] = 127,
+	[0][1][2][1][5][42] = 76,
+	[0][1][2][1][6][42] = 4,
+	[0][1][2][1][9][42] = 76,
+	[0][1][2][1][8][42] = 30,
+	[0][1][2][1][11][42] = 28,
+	[0][1][2][1][2][44] = 76,
+	[0][1][2][1][1][44] = 4,
+	[0][1][2][1][3][44] = 127,
+	[0][1][2][1][5][44] = 76,
+	[0][1][2][1][6][44] = 4,
+	[0][1][2][1][9][44] = 76,
+	[0][1][2][1][8][44] = 30,
+	[0][1][2][1][11][44] = 28,
+	[0][1][2][1][2][46] = 76,
+	[0][1][2][1][1][46] = 4,
+	[0][1][2][1][3][46] = 127,
+	[0][1][2][1][5][46] = 76,
+	[0][1][2][1][6][46] = 4,
+	[0][1][2][1][9][46] = 76,
+	[0][1][2][1][8][46] = 30,
+	[0][1][2][1][11][46] = 28,
+	[1][0][2][0][2][1] = 68,
+	[1][0][2][0][1][1] = 64,
+	[1][0][2][0][3][1] = 62,
+	[1][0][2][0][5][1] = 64,
+	[1][0][2][0][6][1] = 64,
+	[1][0][2][0][9][1] = 64,
+	[1][0][2][0][8][1] = 30,
+	[1][0][2][0][11][1] = 52,
+	[1][0][2][0][2][5] = 72,
+	[1][0][2][0][1][5] = 64,
+	[1][0][2][0][3][5] = 62,
+	[1][0][2][0][5][5] = 64,
+	[1][0][2][0][6][5] = 60,
+	[1][0][2][0][9][5] = 64,
+	[1][0][2][0][8][5] = 30,
+	[1][0][2][0][11][5] = 52,
+	[1][0][2][0][2][9] = 72,
+	[1][0][2][0][1][9] = 64,
+	[1][0][2][0][3][9] = 62,
+	[1][0][2][0][5][9] = 64,
+	[1][0][2][0][6][9] = 64,
+	[1][0][2][0][9][9] = 64,
+	[1][0][2][0][8][9] = 54,
+	[1][0][2][0][11][9] = 52,
+	[1][0][2][0][2][13] = 66,
+	[1][0][2][0][1][13] = 64,
+	[1][0][2][0][3][13] = 62,
+	[1][0][2][0][5][13] = 64,
+	[1][0][2][0][6][13] = 64,
+	[1][0][2][0][9][13] = 64,
+	[1][0][2][0][8][13] = 54,
+	[1][0][2][0][11][13] = 52,
+	[1][0][2][0][2][16] = 62,
+	[1][0][2][0][1][16] = 64,
+	[1][0][2][0][3][16] = 72,
+	[1][0][2][0][5][16] = 62,
+	[1][0][2][0][6][16] = 64,
+	[1][0][2][0][9][16] = 64,
+	[1][0][2][0][8][16] = 54,
+	[1][0][2][0][11][16] = 52,
+	[1][0][2][0][2][20] = 72,
+	[1][0][2][0][1][20] = 64,
+	[1][0][2][0][3][20] = 72,
+	[1][0][2][0][5][20] = 72,
+	[1][0][2][0][6][20] = 64,
+	[1][0][2][0][9][20] = 64,
+	[1][0][2][0][8][20] = 54,
+	[1][0][2][0][11][20] = 52,
+	[1][0][2][0][2][24] = 72,
+	[1][0][2][0][1][24] = 64,
+	[1][0][2][0][3][24] = 72,
+	[1][0][2][0][5][24] = 127,
+	[1][0][2][0][6][24] = 64,
+	[1][0][2][0][9][24] = 127,
+	[1][0][2][0][8][24] = 54,
+	[1][0][2][0][11][24] = 52,
+	[1][0][2][0][2][28] = 72,
+	[1][0][2][0][1][28] = 64,
+	[1][0][2][0][3][28] = 72,
+	[1][0][2][0][5][28] = 127,
+	[1][0][2][0][6][28] = 64,
+	[1][0][2][0][9][28] = 127,
+	[1][0][2][0][8][28] = 54,
+	[1][0][2][0][11][28] = 52,
+	[1][0][2][0][2][32] = 72,
+	[1][0][2][0][1][32] = 64,
+	[1][0][2][0][3][32] = 72,
+	[1][0][2][0][5][32] = 72,
+	[1][0][2][0][6][32] = 64,
+	[1][0][2][0][9][32] = 64,
+	[1][0][2][0][8][32] = 54,
+	[1][0][2][0][11][32] = 52,
+	[1][0][2][0][2][36] = 72,
+	[1][0][2][0][1][36] = 127,
+	[1][0][2][0][3][36] = 72,
+	[1][0][2][0][5][36] = 72,
+	[1][0][2][0][6][36] = 64,
+	[1][0][2][0][9][36] = 72,
+	[1][0][2][0][8][36] = 54,
+	[1][0][2][0][11][36] = 127,
+	[1][0][2][0][2][39] = 72,
+	[1][0][2][0][1][39] = 28,
+	[1][0][2][0][3][39] = 127,
+	[1][0][2][0][5][39] = 72,
+	[1][0][2][0][6][39] = 28,
+	[1][0][2][0][9][39] = 72,
+	[1][0][2][0][8][39] = 54,
+	[1][0][2][0][11][39] = 52,
+	[1][0][2][0][2][43] = 72,
+	[1][0][2][0][1][43] = 28,
+	[1][0][2][0][3][43] = 127,
+	[1][0][2][0][5][43] = 72,
+	[1][0][2][0][6][43] = 28,
+	[1][0][2][0][9][43] = 72,
+	[1][0][2][0][8][43] = 54,
+	[1][0][2][0][11][43] = 52,
+	[1][1][2][0][2][1] = 58,
+	[1][1][2][0][1][1] = 52,
+	[1][1][2][0][3][1] = 50,
+	[1][1][2][0][5][1] = 52,
+	[1][1][2][0][6][1] = 52,
+	[1][1][2][0][9][1] = 52,
+	[1][1][2][0][8][1] = 18,
+	[1][1][2][0][11][1] = 40,
+	[1][1][2][0][2][5] = 72,
+	[1][1][2][0][1][5] = 52,
+	[1][1][2][0][3][5] = 50,
+	[1][1][2][0][5][5] = 52,
+	[1][1][2][0][6][5] = 46,
+	[1][1][2][0][9][5] = 52,
+	[1][1][2][0][8][5] = 18,
+	[1][1][2][0][11][5] = 40,
+	[1][1][2][0][2][9] = 72,
+	[1][1][2][0][1][9] = 52,
+	[1][1][2][0][3][9] = 50,
+	[1][1][2][0][5][9] = 52,
+	[1][1][2][0][6][9] = 52,
+	[1][1][2][0][9][9] = 52,
+	[1][1][2][0][8][9] = 42,
+	[1][1][2][0][11][9] = 40,
+	[1][1][2][0][2][13] = 58,
+	[1][1][2][0][1][13] = 52,
+	[1][1][2][0][3][13] = 50,
+	[1][1][2][0][5][13] = 52,
+	[1][1][2][0][6][13] = 52,
+	[1][1][2][0][9][13] = 52,
+	[1][1][2][0][8][13] = 42,
+	[1][1][2][0][11][13] = 40,
+	[1][1][2][0][2][16] = 56,
+	[1][1][2][0][1][16] = 52,
+	[1][1][2][0][3][16] = 72,
+	[1][1][2][0][5][16] = 56,
+	[1][1][2][0][6][16] = 52,
+	[1][1][2][0][9][16] = 52,
+	[1][1][2][0][8][16] = 42,
+	[1][1][2][0][11][16] = 40,
+	[1][1][2][0][2][20] = 72,
+	[1][1][2][0][1][20] = 52,
+	[1][1][2][0][3][20] = 72,
+	[1][1][2][0][5][20] = 72,
+	[1][1][2][0][6][20] = 52,
+	[1][1][2][0][9][20] = 52,
+	[1][1][2][0][8][20] = 42,
+	[1][1][2][0][11][20] = 40,
+	[1][1][2][0][2][24] = 72,
+	[1][1][2][0][1][24] = 52,
+	[1][1][2][0][3][24] = 72,
+	[1][1][2][0][5][24] = 127,
+	[1][1][2][0][6][24] = 52,
+	[1][1][2][0][9][24] = 127,
+	[1][1][2][0][8][24] = 42,
+	[1][1][2][0][11][24] = 40,
+	[1][1][2][0][2][28] = 72,
+	[1][1][2][0][1][28] = 52,
+	[1][1][2][0][3][28] = 72,
+	[1][1][2][0][5][28] = 127,
+	[1][1][2][0][6][28] = 52,
+	[1][1][2][0][9][28] = 127,
+	[1][1][2][0][8][28] = 42,
+	[1][1][2][0][11][28] = 40,
+	[1][1][2][0][2][32] = 68,
+	[1][1][2][0][1][32] = 52,
+	[1][1][2][0][3][32] = 72,
+	[1][1][2][0][5][32] = 68,
+	[1][1][2][0][6][32] = 52,
+	[1][1][2][0][9][32] = 52,
+	[1][1][2][0][8][32] = 42,
+	[1][1][2][0][11][32] = 40,
+	[1][1][2][0][2][36] = 72,
+	[1][1][2][0][1][36] = 127,
+	[1][1][2][0][3][36] = 72,
+	[1][1][2][0][5][36] = 72,
+	[1][1][2][0][6][36] = 52,
+	[1][1][2][0][9][36] = 72,
+	[1][1][2][0][8][36] = 42,
+	[1][1][2][0][11][36] = 127,
+	[1][1][2][0][2][39] = 72,
+	[1][1][2][0][1][39] = 16,
+	[1][1][2][0][3][39] = 127,
+	[1][1][2][0][5][39] = 72,
+	[1][1][2][0][6][39] = 16,
+	[1][1][2][0][9][39] = 72,
+	[1][1][2][0][8][39] = 42,
+	[1][1][2][0][11][39] = 40,
+	[1][1][2][0][2][43] = 72,
+	[1][1][2][0][1][43] = 16,
+	[1][1][2][0][3][43] = 127,
+	[1][1][2][0][5][43] = 72,
+	[1][1][2][0][6][43] = 16,
+	[1][1][2][0][9][43] = 72,
+	[1][1][2][0][8][43] = 42,
+	[1][1][2][0][11][43] = 40,
+	[1][1][2][1][2][1] = 58,
+	[1][1][2][1][1][1] = 40,
+	[1][1][2][1][3][1] = 50,
+	[1][1][2][1][5][1] = 40,
+	[1][1][2][1][6][1] = 40,
+	[1][1][2][1][9][1] = 40,
+	[1][1][2][1][8][1] = 6,
+	[1][1][2][1][11][1] = 28,
+	[1][1][2][1][2][5] = 68,
+	[1][1][2][1][1][5] = 40,
+	[1][1][2][1][3][5] = 50,
+	[1][1][2][1][5][5] = 40,
+	[1][1][2][1][6][5] = 40,
+	[1][1][2][1][9][5] = 40,
+	[1][1][2][1][8][5] = 6,
+	[1][1][2][1][11][5] = 28,
+	[1][1][2][1][2][9] = 68,
+	[1][1][2][1][1][9] = 40,
+	[1][1][2][1][3][9] = 50,
+	[1][1][2][1][5][9] = 40,
+	[1][1][2][1][6][9] = 40,
+	[1][1][2][1][9][9] = 40,
+	[1][1][2][1][8][9] = 30,
+	[1][1][2][1][11][9] = 28,
+	[1][1][2][1][2][13] = 58,
+	[1][1][2][1][1][13] = 40,
+	[1][1][2][1][3][13] = 50,
+	[1][1][2][1][5][13] = 40,
+	[1][1][2][1][6][13] = 40,
+	[1][1][2][1][9][13] = 40,
+	[1][1][2][1][8][13] = 30,
+	[1][1][2][1][11][13] = 28,
+	[1][1][2][1][2][16] = 56,
+	[1][1][2][1][1][16] = 40,
+	[1][1][2][1][3][16] = 72,
+	[1][1][2][1][5][16] = 56,
+	[1][1][2][1][6][16] = 40,
+	[1][1][2][1][9][16] = 40,
+	[1][1][2][1][8][16] = 30,
+	[1][1][2][1][11][16] = 28,
+	[1][1][2][1][2][20] = 68,
+	[1][1][2][1][1][20] = 40,
+	[1][1][2][1][3][20] = 72,
+	[1][1][2][1][5][20] = 68,
+	[1][1][2][1][6][20] = 40,
+	[1][1][2][1][9][20] = 40,
+	[1][1][2][1][8][20] = 30,
+	[1][1][2][1][11][20] = 28,
+	[1][1][2][1][2][24] = 68,
+	[1][1][2][1][1][24] = 40,
+	[1][1][2][1][3][24] = 72,
+	[1][1][2][1][5][24] = 127,
+	[1][1][2][1][6][24] = 40,
+	[1][1][2][1][9][24] = 127,
+	[1][1][2][1][8][24] = 30,
+	[1][1][2][1][11][24] = 28,
+	[1][1][2][1][2][28] = 68,
+	[1][1][2][1][1][28] = 40,
+	[1][1][2][1][3][28] = 72,
+	[1][1][2][1][5][28] = 127,
+	[1][1][2][1][6][28] = 40,
+	[1][1][2][1][9][28] = 127,
+	[1][1][2][1][8][28] = 30,
+	[1][1][2][1][11][28] = 28,
+	[1][1][2][1][2][32] = 68,
+	[1][1][2][1][1][32] = 40,
+	[1][1][2][1][3][32] = 72,
+	[1][1][2][1][5][32] = 68,
+	[1][1][2][1][6][32] = 40,
+	[1][1][2][1][9][32] = 40,
+	[1][1][2][1][8][32] = 30,
+	[1][1][2][1][11][32] = 28,
+	[1][1][2][1][2][36] = 68,
+	[1][1][2][1][1][36] = 127,
+	[1][1][2][1][3][36] = 72,
+	[1][1][2][1][5][36] = 68,
+	[1][1][2][1][6][36] = 40,
+	[1][1][2][1][9][36] = 68,
+	[1][1][2][1][8][36] = 30,
+	[1][1][2][1][11][36] = 127,
+	[1][1][2][1][2][39] = 72,
+	[1][1][2][1][1][39] = 4,
+	[1][1][2][1][3][39] = 127,
+	[1][1][2][1][5][39] = 72,
+	[1][1][2][1][6][39] = 4,
+	[1][1][2][1][9][39] = 72,
+	[1][1][2][1][8][39] = 30,
+	[1][1][2][1][11][39] = 28,
+	[1][1][2][1][2][43] = 72,
+	[1][1][2][1][1][43] = 4,
+	[1][1][2][1][3][43] = 127,
+	[1][1][2][1][5][43] = 72,
+	[1][1][2][1][6][43] = 4,
+	[1][1][2][1][9][43] = 72,
+	[1][1][2][1][8][43] = 30,
+	[1][1][2][1][11][43] = 28,
+	[2][0][2][0][2][3] = 64,
+	[2][0][2][0][1][3] = 64,
+	[2][0][2][0][3][3] = 64,
+	[2][0][2][0][5][3] = 62,
+	[2][0][2][0][6][3] = 64,
+	[2][0][2][0][9][3] = 64,
+	[2][0][2][0][8][3] = 30,
+	[2][0][2][0][11][3] = 52,
+	[2][0][2][0][2][11] = 64,
+	[2][0][2][0][1][11] = 64,
+	[2][0][2][0][3][11] = 64,
+	[2][0][2][0][5][11] = 62,
+	[2][0][2][0][6][11] = 64,
+	[2][0][2][0][9][11] = 64,
+	[2][0][2][0][8][11] = 54,
+	[2][0][2][0][11][11] = 52,
+	[2][0][2][0][2][18] = 62,
+	[2][0][2][0][1][18] = 64,
+	[2][0][2][0][3][18] = 72,
+	[2][0][2][0][5][18] = 66,
+	[2][0][2][0][6][18] = 64,
+	[2][0][2][0][9][18] = 64,
+	[2][0][2][0][8][18] = 54,
+	[2][0][2][0][11][18] = 52,
+	[2][0][2][0][2][26] = 72,
+	[2][0][2][0][1][26] = 64,
+	[2][0][2][0][3][26] = 72,
+	[2][0][2][0][5][26] = 127,
+	[2][0][2][0][6][26] = 64,
+	[2][0][2][0][9][26] = 127,
+	[2][0][2][0][8][26] = 54,
+	[2][0][2][0][11][26] = 52,
+	[2][0][2][0][2][34] = 72,
+	[2][0][2][0][1][34] = 127,
+	[2][0][2][0][3][34] = 72,
+	[2][0][2][0][5][34] = 72,
+	[2][0][2][0][6][34] = 64,
+	[2][0][2][0][9][34] = 72,
+	[2][0][2][0][8][34] = 54,
+	[2][0][2][0][11][34] = 127,
+	[2][0][2][0][2][41] = 72,
+	[2][0][2][0][1][41] = 28,
+	[2][0][2][0][3][41] = 127,
+	[2][0][2][0][5][41] = 72,
+	[2][0][2][0][6][41] = 28,
+	[2][0][2][0][9][41] = 72,
+	[2][0][2][0][8][41] = 54,
+	[2][0][2][0][11][41] = 52,
+	[2][1][2][0][2][3] = 56,
+	[2][1][2][0][1][3] = 52,
+	[2][1][2][0][3][3] = 52,
+	[2][1][2][0][5][3] = 52,
+	[2][1][2][0][6][3] = 52,
+	[2][1][2][0][9][3] = 52,
+	[2][1][2][0][8][3] = 18,
+	[2][1][2][0][11][3] = 40,
+	[2][1][2][0][2][11] = 56,
+	[2][1][2][0][1][11] = 52,
+	[2][1][2][0][3][11] = 52,
+	[2][1][2][0][5][11] = 52,
+	[2][1][2][0][6][11] = 52,
+	[2][1][2][0][9][11] = 52,
+	[2][1][2][0][8][11] = 42,
+	[2][1][2][0][11][11] = 40,
+	[2][1][2][0][2][18] = 56,
+	[2][1][2][0][1][18] = 52,
+	[2][1][2][0][3][18] = 72,
+	[2][1][2][0][5][18] = 56,
+	[2][1][2][0][6][18] = 52,
+	[2][1][2][0][9][18] = 52,
+	[2][1][2][0][8][18] = 42,
+	[2][1][2][0][11][18] = 40,
+	[2][1][2][0][2][26] = 72,
+	[2][1][2][0][1][26] = 52,
+	[2][1][2][0][3][26] = 72,
+	[2][1][2][0][5][26] = 127,
+	[2][1][2][0][6][26] = 52,
+	[2][1][2][0][9][26] = 127,
+	[2][1][2][0][8][26] = 42,
+	[2][1][2][0][11][26] = 40,
+	[2][1][2][0][2][34] = 72,
+	[2][1][2][0][1][34] = 127,
+	[2][1][2][0][3][34] = 72,
+	[2][1][2][0][5][34] = 72,
+	[2][1][2][0][6][34] = 52,
+	[2][1][2][0][9][34] = 72,
+	[2][1][2][0][8][34] = 42,
+	[2][1][2][0][11][34] = 127,
+	[2][1][2][0][2][41] = 72,
+	[2][1][2][0][1][41] = 16,
+	[2][1][2][0][3][41] = 127,
+	[2][1][2][0][5][41] = 72,
+	[2][1][2][0][6][41] = 16,
+	[2][1][2][0][9][41] = 72,
+	[2][1][2][0][8][41] = 42,
+	[2][1][2][0][11][41] = 40,
+	[2][1][2][1][2][3] = 56,
+	[2][1][2][1][1][3] = 40,
+	[2][1][2][1][3][3] = 52,
+	[2][1][2][1][5][3] = 40,
+	[2][1][2][1][6][3] = 40,
+	[2][1][2][1][9][3] = 40,
+	[2][1][2][1][8][3] = 6,
+	[2][1][2][1][11][3] = 28,
+	[2][1][2][1][2][11] = 56,
+	[2][1][2][1][1][11] = 40,
+	[2][1][2][1][3][11] = 52,
+	[2][1][2][1][5][11] = 40,
+	[2][1][2][1][6][11] = 40,
+	[2][1][2][1][9][11] = 40,
+	[2][1][2][1][8][11] = 30,
+	[2][1][2][1][11][11] = 28,
+	[2][1][2][1][2][18] = 56,
+	[2][1][2][1][1][18] = 40,
+	[2][1][2][1][3][18] = 72,
+	[2][1][2][1][5][18] = 56,
+	[2][1][2][1][6][18] = 40,
+	[2][1][2][1][9][18] = 40,
+	[2][1][2][1][8][18] = 30,
+	[2][1][2][1][11][18] = 28,
+	[2][1][2][1][2][26] = 68,
+	[2][1][2][1][1][26] = 40,
+	[2][1][2][1][3][26] = 72,
+	[2][1][2][1][5][26] = 127,
+	[2][1][2][1][6][26] = 40,
+	[2][1][2][1][9][26] = 127,
+	[2][1][2][1][8][26] = 30,
+	[2][1][2][1][11][26] = 28,
+	[2][1][2][1][2][34] = 68,
+	[2][1][2][1][1][34] = 127,
+	[2][1][2][1][3][34] = 72,
+	[2][1][2][1][5][34] = 68,
+	[2][1][2][1][6][34] = 40,
+	[2][1][2][1][9][34] = 68,
+	[2][1][2][1][8][34] = 30,
+	[2][1][2][1][11][34] = 127,
+	[2][1][2][1][2][41] = 72,
+	[2][1][2][1][1][41] = 4,
+	[2][1][2][1][3][41] = 127,
+	[2][1][2][1][5][41] = 72,
+	[2][1][2][1][6][41] = 4,
+	[2][1][2][1][9][41] = 72,
+	[2][1][2][1][8][41] = 30,
+	[2][1][2][1][11][41] = 28,
+};
+
+const s8 rtw89_8852a_txpwr_lmt_ru_2g[RTW89_RU_NUM][RTW89_NTX_NUM]
+				    [RTW89_REGD_NUM][RTW89_2G_CH_NUM] = {
+	[0][0][0][0] = 32,
+	[0][0][0][1] = 32,
+	[0][0][0][2] = 32,
+	[0][0][0][3] = 32,
+	[0][0][0][4] = 32,
+	[0][0][0][5] = 32,
+	[0][0][0][6] = 32,
+	[0][0][0][7] = 32,
+	[0][0][0][8] = 32,
+	[0][0][0][9] = 32,
+	[0][0][0][10] = 32,
+	[0][0][0][11] = 32,
+	[0][0][0][12] = 32,
+	[0][0][0][13] = 0,
+	[0][1][0][0] = 20,
+	[0][1][0][1] = 20,
+	[0][1][0][2] = 20,
+	[0][1][0][3] = 20,
+	[0][1][0][4] = 20,
+	[0][1][0][5] = 20,
+	[0][1][0][6] = 20,
+	[0][1][0][7] = 20,
+	[0][1][0][8] = 20,
+	[0][1][0][9] = 20,
+	[0][1][0][10] = 20,
+	[0][1][0][11] = 20,
+	[0][1][0][12] = 20,
+	[0][1][0][13] = 0,
+	[1][0][0][0] = 42,
+	[1][0][0][1] = 42,
+	[1][0][0][2] = 42,
+	[1][0][0][3] = 42,
+	[1][0][0][4] = 42,
+	[1][0][0][5] = 42,
+	[1][0][0][6] = 42,
+	[1][0][0][7] = 42,
+	[1][0][0][8] = 42,
+	[1][0][0][9] = 42,
+	[1][0][0][10] = 42,
+	[1][0][0][11] = 42,
+	[1][0][0][12] = 36,
+	[1][0][0][13] = 0,
+	[1][1][0][0] = 30,
+	[1][1][0][1] = 30,
+	[1][1][0][2] = 30,
+	[1][1][0][3] = 30,
+	[1][1][0][4] = 30,
+	[1][1][0][5] = 30,
+	[1][1][0][6] = 30,
+	[1][1][0][7] = 30,
+	[1][1][0][8] = 30,
+	[1][1][0][9] = 30,
+	[1][1][0][10] = 30,
+	[1][1][0][11] = 30,
+	[1][1][0][12] = 30,
+	[1][1][0][13] = 0,
+	[2][0][0][0] = 52,
+	[2][0][0][1] = 52,
+	[2][0][0][2] = 52,
+	[2][0][0][3] = 52,
+	[2][0][0][4] = 52,
+	[2][0][0][5] = 52,
+	[2][0][0][6] = 52,
+	[2][0][0][7] = 52,
+	[2][0][0][8] = 52,
+	[2][0][0][9] = 52,
+	[2][0][0][10] = 52,
+	[2][0][0][11] = 52,
+	[2][0][0][12] = 40,
+	[2][0][0][13] = 0,
+	[2][1][0][0] = 40,
+	[2][1][0][1] = 40,
+	[2][1][0][2] = 40,
+	[2][1][0][3] = 40,
+	[2][1][0][4] = 40,
+	[2][1][0][5] = 40,
+	[2][1][0][6] = 40,
+	[2][1][0][7] = 40,
+	[2][1][0][8] = 40,
+	[2][1][0][9] = 40,
+	[2][1][0][10] = 40,
+	[2][1][0][11] = 40,
+	[2][1][0][12] = 26,
+	[2][1][0][13] = 0,
+	[0][0][2][0] = 70,
+	[0][0][1][0] = 32,
+	[0][0][3][0] = 40,
+	[0][0][5][0] = 70,
+	[0][0][6][0] = 32,
+	[0][0][9][0] = 32,
+	[0][0][8][0] = 60,
+	[0][0][11][0] = 32,
+	[0][0][2][1] = 70,
+	[0][0][1][1] = 32,
+	[0][0][3][1] = 40,
+	[0][0][5][1] = 70,
+	[0][0][6][1] = 32,
+	[0][0][9][1] = 32,
+	[0][0][8][1] = 60,
+	[0][0][11][1] = 32,
+	[0][0][2][2] = 74,
+	[0][0][1][2] = 32,
+	[0][0][3][2] = 40,
+	[0][0][5][2] = 74,
+	[0][0][6][2] = 32,
+	[0][0][9][2] = 32,
+	[0][0][8][2] = 60,
+	[0][0][11][2] = 32,
+	[0][0][2][3] = 78,
+	[0][0][1][3] = 32,
+	[0][0][3][3] = 40,
+	[0][0][5][3] = 78,
+	[0][0][6][3] = 32,
+	[0][0][9][3] = 32,
+	[0][0][8][3] = 60,
+	[0][0][11][3] = 32,
+	[0][0][2][4] = 78,
+	[0][0][1][4] = 32,
+	[0][0][3][4] = 40,
+	[0][0][5][4] = 78,
+	[0][0][6][4] = 32,
+	[0][0][9][4] = 32,
+	[0][0][8][4] = 60,
+	[0][0][11][4] = 32,
+	[0][0][2][5] = 78,
+	[0][0][1][5] = 32,
+	[0][0][3][5] = 40,
+	[0][0][5][5] = 78,
+	[0][0][6][5] = 32,
+	[0][0][9][5] = 32,
+	[0][0][8][5] = 60,
+	[0][0][11][5] = 32,
+	[0][0][2][6] = 78,
+	[0][0][1][6] = 32,
+	[0][0][3][6] = 40,
+	[0][0][5][6] = 78,
+	[0][0][6][6] = 32,
+	[0][0][9][6] = 32,
+	[0][0][8][6] = 60,
+	[0][0][11][6] = 32,
+	[0][0][2][7] = 78,
+	[0][0][1][7] = 32,
+	[0][0][3][7] = 40,
+	[0][0][5][7] = 78,
+	[0][0][6][7] = 32,
+	[0][0][9][7] = 32,
+	[0][0][8][7] = 60,
+	[0][0][11][7] = 32,
+	[0][0][2][8] = 74,
+	[0][0][1][8] = 32,
+	[0][0][3][8] = 40,
+	[0][0][5][8] = 74,
+	[0][0][6][8] = 32,
+	[0][0][9][8] = 32,
+	[0][0][8][8] = 60,
+	[0][0][11][8] = 32,
+	[0][0][2][9] = 70,
+	[0][0][1][9] = 32,
+	[0][0][3][9] = 40,
+	[0][0][5][9] = 70,
+	[0][0][6][9] = 32,
+	[0][0][9][9] = 32,
+	[0][0][8][9] = 60,
+	[0][0][11][9] = 32,
+	[0][0][2][10] = 70,
+	[0][0][1][10] = 32,
+	[0][0][3][10] = 40,
+	[0][0][5][10] = 70,
+	[0][0][6][10] = 32,
+	[0][0][9][10] = 32,
+	[0][0][8][10] = 60,
+	[0][0][11][10] = 32,
+	[0][0][2][11] = 58,
+	[0][0][1][11] = 32,
+	[0][0][3][11] = 40,
+	[0][0][5][11] = 58,
+	[0][0][6][11] = 32,
+	[0][0][9][11] = 32,
+	[0][0][8][11] = 60,
+	[0][0][11][11] = 32,
+	[0][0][2][12] = 34,
+	[0][0][1][12] = 32,
+	[0][0][3][12] = 40,
+	[0][0][5][12] = 34,
+	[0][0][6][12] = 32,
+	[0][0][9][12] = 32,
+	[0][0][8][12] = 60,
+	[0][0][11][12] = 32,
+	[0][0][2][13] = 127,
+	[0][0][1][13] = 127,
+	[0][0][3][13] = 127,
+	[0][0][5][13] = 127,
+	[0][0][6][13] = 127,
+	[0][0][9][13] = 127,
+	[0][0][8][13] = 127,
+	[0][0][11][13] = 127,
+	[0][1][2][0] = 64,
+	[0][1][1][0] = 20,
+	[0][1][3][0] = 28,
+	[0][1][5][0] = 64,
+	[0][1][6][0] = 20,
+	[0][1][9][0] = 20,
+	[0][1][8][0] = 48,
+	[0][1][11][0] = 20,
+	[0][1][2][1] = 64,
+	[0][1][1][1] = 20,
+	[0][1][3][1] = 28,
+	[0][1][5][1] = 64,
+	[0][1][6][1] = 20,
+	[0][1][9][1] = 20,
+	[0][1][8][1] = 48,
+	[0][1][11][1] = 20,
+	[0][1][2][2] = 68,
+	[0][1][1][2] = 20,
+	[0][1][3][2] = 28,
+	[0][1][5][2] = 68,
+	[0][1][6][2] = 20,
+	[0][1][9][2] = 20,
+	[0][1][8][2] = 48,
+	[0][1][11][2] = 20,
+	[0][1][2][3] = 72,
+	[0][1][1][3] = 20,
+	[0][1][3][3] = 28,
+	[0][1][5][3] = 72,
+	[0][1][6][3] = 20,
+	[0][1][9][3] = 20,
+	[0][1][8][3] = 48,
+	[0][1][11][3] = 20,
+	[0][1][2][4] = 76,
+	[0][1][1][4] = 20,
+	[0][1][3][4] = 28,
+	[0][1][5][4] = 76,
+	[0][1][6][4] = 20,
+	[0][1][9][4] = 20,
+	[0][1][8][4] = 48,
+	[0][1][11][4] = 20,
+	[0][1][2][5] = 78,
+	[0][1][1][5] = 20,
+	[0][1][3][5] = 28,
+	[0][1][5][5] = 78,
+	[0][1][6][5] = 20,
+	[0][1][9][5] = 20,
+	[0][1][8][5] = 48,
+	[0][1][11][5] = 20,
+	[0][1][2][6] = 76,
+	[0][1][1][6] = 20,
+	[0][1][3][6] = 28,
+	[0][1][5][6] = 76,
+	[0][1][6][6] = 20,
+	[0][1][9][6] = 20,
+	[0][1][8][6] = 48,
+	[0][1][11][6] = 20,
+	[0][1][2][7] = 72,
+	[0][1][1][7] = 20,
+	[0][1][3][7] = 28,
+	[0][1][5][7] = 72,
+	[0][1][6][7] = 20,
+	[0][1][9][7] = 20,
+	[0][1][8][7] = 48,
+	[0][1][11][7] = 20,
+	[0][1][2][8] = 68,
+	[0][1][1][8] = 20,
+	[0][1][3][8] = 28,
+	[0][1][5][8] = 68,
+	[0][1][6][8] = 20,
+	[0][1][9][8] = 20,
+	[0][1][8][8] = 48,
+	[0][1][11][8] = 20,
+	[0][1][2][9] = 64,
+	[0][1][1][9] = 20,
+	[0][1][3][9] = 28,
+	[0][1][5][9] = 64,
+	[0][1][6][9] = 20,
+	[0][1][9][9] = 20,
+	[0][1][8][9] = 48,
+	[0][1][11][9] = 20,
+	[0][1][2][10] = 64,
+	[0][1][1][10] = 20,
+	[0][1][3][10] = 28,
+	[0][1][5][10] = 64,
+	[0][1][6][10] = 20,
+	[0][1][9][10] = 20,
+	[0][1][8][10] = 48,
+	[0][1][11][10] = 20,
+	[0][1][2][11] = 54,
+	[0][1][1][11] = 20,
+	[0][1][3][11] = 28,
+	[0][1][5][11] = 54,
+	[0][1][6][11] = 20,
+	[0][1][9][11] = 20,
+	[0][1][8][11] = 48,
+	[0][1][11][11] = 20,
+	[0][1][2][12] = 32,
+	[0][1][1][12] = 20,
+	[0][1][3][12] = 28,
+	[0][1][5][12] = 32,
+	[0][1][6][12] = 20,
+	[0][1][9][12] = 20,
+	[0][1][8][12] = 48,
+	[0][1][11][12] = 20,
+	[0][1][2][13] = 127,
+	[0][1][1][13] = 127,
+	[0][1][3][13] = 127,
+	[0][1][5][13] = 127,
+	[0][1][6][13] = 127,
+	[0][1][9][13] = 127,
+	[0][1][8][13] = 127,
+	[0][1][11][13] = 127,
+	[1][0][2][0] = 72,
+	[1][0][1][0] = 42,
+	[1][0][3][0] = 50,
+	[1][0][5][0] = 72,
+	[1][0][6][0] = 42,
+	[1][0][9][0] = 42,
+	[1][0][8][0] = 60,
+	[1][0][11][0] = 42,
+	[1][0][2][1] = 72,
+	[1][0][1][1] = 42,
+	[1][0][3][1] = 50,
+	[1][0][5][1] = 72,
+	[1][0][6][1] = 42,
+	[1][0][9][1] = 42,
+	[1][0][8][1] = 60,
+	[1][0][11][1] = 42,
+	[1][0][2][2] = 76,
+	[1][0][1][2] = 42,
+	[1][0][3][2] = 50,
+	[1][0][5][2] = 76,
+	[1][0][6][2] = 42,
+	[1][0][9][2] = 42,
+	[1][0][8][2] = 60,
+	[1][0][11][2] = 42,
+	[1][0][2][3] = 78,
+	[1][0][1][3] = 42,
+	[1][0][3][3] = 50,
+	[1][0][5][3] = 78,
+	[1][0][6][3] = 42,
+	[1][0][9][3] = 42,
+	[1][0][8][3] = 60,
+	[1][0][11][3] = 42,
+	[1][0][2][4] = 78,
+	[1][0][1][4] = 42,
+	[1][0][3][4] = 50,
+	[1][0][5][4] = 78,
+	[1][0][6][4] = 42,
+	[1][0][9][4] = 42,
+	[1][0][8][4] = 60,
+	[1][0][11][4] = 42,
+	[1][0][2][5] = 78,
+	[1][0][1][5] = 42,
+	[1][0][3][5] = 50,
+	[1][0][5][5] = 78,
+	[1][0][6][5] = 42,
+	[1][0][9][5] = 42,
+	[1][0][8][5] = 60,
+	[1][0][11][5] = 42,
+	[1][0][2][6] = 78,
+	[1][0][1][6] = 42,
+	[1][0][3][6] = 50,
+	[1][0][5][6] = 78,
+	[1][0][6][6] = 42,
+	[1][0][9][6] = 42,
+	[1][0][8][6] = 60,
+	[1][0][11][6] = 42,
+	[1][0][2][7] = 78,
+	[1][0][1][7] = 42,
+	[1][0][3][7] = 50,
+	[1][0][5][7] = 78,
+	[1][0][6][7] = 42,
+	[1][0][9][7] = 42,
+	[1][0][8][7] = 60,
+	[1][0][11][7] = 42,
+	[1][0][2][8] = 78,
+	[1][0][1][8] = 42,
+	[1][0][3][8] = 50,
+	[1][0][5][8] = 78,
+	[1][0][6][8] = 42,
+	[1][0][9][8] = 42,
+	[1][0][8][8] = 60,
+	[1][0][11][8] = 42,
+	[1][0][2][9] = 74,
+	[1][0][1][9] = 42,
+	[1][0][3][9] = 50,
+	[1][0][5][9] = 74,
+	[1][0][6][9] = 42,
+	[1][0][9][9] = 42,
+	[1][0][8][9] = 60,
+	[1][0][11][9] = 42,
+	[1][0][2][10] = 74,
+	[1][0][1][10] = 42,
+	[1][0][3][10] = 50,
+	[1][0][5][10] = 74,
+	[1][0][6][10] = 42,
+	[1][0][9][10] = 42,
+	[1][0][8][10] = 60,
+	[1][0][11][10] = 42,
+	[1][0][2][11] = 64,
+	[1][0][1][11] = 42,
+	[1][0][3][11] = 50,
+	[1][0][5][11] = 64,
+	[1][0][6][11] = 42,
+	[1][0][9][11] = 42,
+	[1][0][8][11] = 60,
+	[1][0][11][11] = 42,
+	[1][0][2][12] = 36,
+	[1][0][1][12] = 42,
+	[1][0][3][12] = 50,
+	[1][0][5][12] = 36,
+	[1][0][6][12] = 42,
+	[1][0][9][12] = 42,
+	[1][0][8][12] = 60,
+	[1][0][11][12] = 42,
+	[1][0][2][13] = 127,
+	[1][0][1][13] = 127,
+	[1][0][3][13] = 127,
+	[1][0][5][13] = 127,
+	[1][0][6][13] = 127,
+	[1][0][9][13] = 127,
+	[1][0][8][13] = 127,
+	[1][0][11][13] = 127,
+	[1][1][2][0] = 66,
+	[1][1][1][0] = 30,
+	[1][1][3][0] = 38,
+	[1][1][5][0] = 66,
+	[1][1][6][0] = 30,
+	[1][1][9][0] = 30,
+	[1][1][8][0] = 48,
+	[1][1][11][0] = 30,
+	[1][1][2][1] = 66,
+	[1][1][1][1] = 30,
+	[1][1][3][1] = 38,
+	[1][1][5][1] = 66,
+	[1][1][6][1] = 30,
+	[1][1][9][1] = 30,
+	[1][1][8][1] = 48,
+	[1][1][11][1] = 30,
+	[1][1][2][2] = 70,
+	[1][1][1][2] = 30,
+	[1][1][3][2] = 38,
+	[1][1][5][2] = 70,
+	[1][1][6][2] = 30,
+	[1][1][9][2] = 30,
+	[1][1][8][2] = 48,
+	[1][1][11][2] = 30,
+	[1][1][2][3] = 74,
+	[1][1][1][3] = 30,
+	[1][1][3][3] = 38,
+	[1][1][5][3] = 74,
+	[1][1][6][3] = 30,
+	[1][1][9][3] = 30,
+	[1][1][8][3] = 48,
+	[1][1][11][3] = 30,
+	[1][1][2][4] = 78,
+	[1][1][1][4] = 30,
+	[1][1][3][4] = 38,
+	[1][1][5][4] = 78,
+	[1][1][6][4] = 30,
+	[1][1][9][4] = 30,
+	[1][1][8][4] = 48,
+	[1][1][11][4] = 30,
+	[1][1][2][5] = 78,
+	[1][1][1][5] = 30,
+	[1][1][3][5] = 38,
+	[1][1][5][5] = 78,
+	[1][1][6][5] = 30,
+	[1][1][9][5] = 30,
+	[1][1][8][5] = 48,
+	[1][1][11][5] = 30,
+	[1][1][2][6] = 78,
+	[1][1][1][6] = 30,
+	[1][1][3][6] = 38,
+	[1][1][5][6] = 78,
+	[1][1][6][6] = 30,
+	[1][1][9][6] = 30,
+	[1][1][8][6] = 48,
+	[1][1][11][6] = 30,
+	[1][1][2][7] = 74,
+	[1][1][1][7] = 30,
+	[1][1][3][7] = 38,
+	[1][1][5][7] = 74,
+	[1][1][6][7] = 30,
+	[1][1][9][7] = 30,
+	[1][1][8][7] = 48,
+	[1][1][11][7] = 30,
+	[1][1][2][8] = 70,
+	[1][1][1][8] = 30,
+	[1][1][3][8] = 38,
+	[1][1][5][8] = 70,
+	[1][1][6][8] = 30,
+	[1][1][9][8] = 30,
+	[1][1][8][8] = 48,
+	[1][1][11][8] = 30,
+	[1][1][2][9] = 66,
+	[1][1][1][9] = 30,
+	[1][1][3][9] = 38,
+	[1][1][5][9] = 66,
+	[1][1][6][9] = 30,
+	[1][1][9][9] = 30,
+	[1][1][8][9] = 48,
+	[1][1][11][9] = 30,
+	[1][1][2][10] = 66,
+	[1][1][1][10] = 30,
+	[1][1][3][10] = 38,
+	[1][1][5][10] = 66,
+	[1][1][6][10] = 30,
+	[1][1][9][10] = 30,
+	[1][1][8][10] = 48,
+	[1][1][11][10] = 30,
+	[1][1][2][11] = 60,
+	[1][1][1][11] = 30,
+	[1][1][3][11] = 38,
+	[1][1][5][11] = 60,
+	[1][1][6][11] = 30,
+	[1][1][9][11] = 30,
+	[1][1][8][11] = 48,
+	[1][1][11][11] = 30,
+	[1][1][2][12] = 32,
+	[1][1][1][12] = 30,
+	[1][1][3][12] = 38,
+	[1][1][5][12] = 32,
+	[1][1][6][12] = 30,
+	[1][1][9][12] = 30,
+	[1][1][8][12] = 48,
+	[1][1][11][12] = 30,
+	[1][1][2][13] = 127,
+	[1][1][1][13] = 127,
+	[1][1][3][13] = 127,
+	[1][1][5][13] = 127,
+	[1][1][6][13] = 127,
+	[1][1][9][13] = 127,
+	[1][1][8][13] = 127,
+	[1][1][11][13] = 127,
+	[2][0][2][0] = 76,
+	[2][0][1][0] = 52,
+	[2][0][3][0] = 64,
+	[2][0][5][0] = 76,
+	[2][0][6][0] = 52,
+	[2][0][9][0] = 52,
+	[2][0][8][0] = 60,
+	[2][0][11][0] = 52,
+	[2][0][2][1] = 76,
+	[2][0][1][1] = 52,
+	[2][0][3][1] = 64,
+	[2][0][5][1] = 76,
+	[2][0][6][1] = 52,
+	[2][0][9][1] = 52,
+	[2][0][8][1] = 60,
+	[2][0][11][1] = 52,
+	[2][0][2][2] = 78,
+	[2][0][1][2] = 52,
+	[2][0][3][2] = 64,
+	[2][0][5][2] = 78,
+	[2][0][6][2] = 52,
+	[2][0][9][2] = 52,
+	[2][0][8][2] = 60,
+	[2][0][11][2] = 52,
+	[2][0][2][3] = 78,
+	[2][0][1][3] = 52,
+	[2][0][3][3] = 64,
+	[2][0][5][3] = 78,
+	[2][0][6][3] = 52,
+	[2][0][9][3] = 52,
+	[2][0][8][3] = 60,
+	[2][0][11][3] = 52,
+	[2][0][2][4] = 78,
+	[2][0][1][4] = 52,
+	[2][0][3][4] = 64,
+	[2][0][5][4] = 78,
+	[2][0][6][4] = 52,
+	[2][0][9][4] = 52,
+	[2][0][8][4] = 60,
+	[2][0][11][4] = 52,
+	[2][0][2][5] = 78,
+	[2][0][1][5] = 52,
+	[2][0][3][5] = 64,
+	[2][0][5][5] = 78,
+	[2][0][6][5] = 52,
+	[2][0][9][5] = 52,
+	[2][0][8][5] = 60,
+	[2][0][11][5] = 52,
+	[2][0][2][6] = 78,
+	[2][0][1][6] = 52,
+	[2][0][3][6] = 64,
+	[2][0][5][6] = 78,
+	[2][0][6][6] = 52,
+	[2][0][9][6] = 52,
+	[2][0][8][6] = 60,
+	[2][0][11][6] = 52,
+	[2][0][2][7] = 78,
+	[2][0][1][7] = 52,
+	[2][0][3][7] = 64,
+	[2][0][5][7] = 78,
+	[2][0][6][7] = 52,
+	[2][0][9][7] = 52,
+	[2][0][8][7] = 60,
+	[2][0][11][7] = 52,
+	[2][0][2][8] = 78,
+	[2][0][1][8] = 52,
+	[2][0][3][8] = 64,
+	[2][0][5][8] = 78,
+	[2][0][6][8] = 52,
+	[2][0][9][8] = 52,
+	[2][0][8][8] = 60,
+	[2][0][11][8] = 52,
+	[2][0][2][9] = 76,
+	[2][0][1][9] = 52,
+	[2][0][3][9] = 64,
+	[2][0][5][9] = 76,
+	[2][0][6][9] = 52,
+	[2][0][9][9] = 52,
+	[2][0][8][9] = 60,
+	[2][0][11][9] = 52,
+	[2][0][2][10] = 76,
+	[2][0][1][10] = 52,
+	[2][0][3][10] = 64,
+	[2][0][5][10] = 76,
+	[2][0][6][10] = 52,
+	[2][0][9][10] = 52,
+	[2][0][8][10] = 60,
+	[2][0][11][10] = 52,
+	[2][0][2][11] = 68,
+	[2][0][1][11] = 52,
+	[2][0][3][11] = 64,
+	[2][0][5][11] = 68,
+	[2][0][6][11] = 52,
+	[2][0][9][11] = 52,
+	[2][0][8][11] = 60,
+	[2][0][11][11] = 52,
+	[2][0][2][12] = 40,
+	[2][0][1][12] = 52,
+	[2][0][3][12] = 64,
+	[2][0][5][12] = 40,
+	[2][0][6][12] = 52,
+	[2][0][9][12] = 52,
+	[2][0][8][12] = 60,
+	[2][0][11][12] = 52,
+	[2][0][2][13] = 127,
+	[2][0][1][13] = 127,
+	[2][0][3][13] = 127,
+	[2][0][5][13] = 127,
+	[2][0][6][13] = 127,
+	[2][0][9][13] = 127,
+	[2][0][8][13] = 127,
+	[2][0][11][13] = 127,
+	[2][1][2][0] = 68,
+	[2][1][1][0] = 40,
+	[2][1][3][0] = 52,
+	[2][1][5][0] = 68,
+	[2][1][6][0] = 40,
+	[2][1][9][0] = 40,
+	[2][1][8][0] = 48,
+	[2][1][11][0] = 40,
+	[2][1][2][1] = 68,
+	[2][1][1][1] = 40,
+	[2][1][3][1] = 52,
+	[2][1][5][1] = 68,
+	[2][1][6][1] = 40,
+	[2][1][9][1] = 40,
+	[2][1][8][1] = 48,
+	[2][1][11][1] = 40,
+	[2][1][2][2] = 72,
+	[2][1][1][2] = 40,
+	[2][1][3][2] = 52,
+	[2][1][5][2] = 72,
+	[2][1][6][2] = 40,
+	[2][1][9][2] = 40,
+	[2][1][8][2] = 48,
+	[2][1][11][2] = 40,
+	[2][1][2][3] = 76,
+	[2][1][1][3] = 40,
+	[2][1][3][3] = 52,
+	[2][1][5][3] = 76,
+	[2][1][6][3] = 40,
+	[2][1][9][3] = 40,
+	[2][1][8][3] = 48,
+	[2][1][11][3] = 40,
+	[2][1][2][4] = 78,
+	[2][1][1][4] = 40,
+	[2][1][3][4] = 52,
+	[2][1][5][4] = 78,
+	[2][1][6][4] = 40,
+	[2][1][9][4] = 40,
+	[2][1][8][4] = 48,
+	[2][1][11][4] = 40,
+	[2][1][2][5] = 78,
+	[2][1][1][5] = 40,
+	[2][1][3][5] = 52,
+	[2][1][5][5] = 78,
+	[2][1][6][5] = 40,
+	[2][1][9][5] = 40,
+	[2][1][8][5] = 48,
+	[2][1][11][5] = 40,
+	[2][1][2][6] = 78,
+	[2][1][1][6] = 40,
+	[2][1][3][6] = 52,
+	[2][1][5][6] = 78,
+	[2][1][6][6] = 40,
+	[2][1][9][6] = 40,
+	[2][1][8][6] = 48,
+	[2][1][11][6] = 40,
+	[2][1][2][7] = 78,
+	[2][1][1][7] = 40,
+	[2][1][3][7] = 52,
+	[2][1][5][7] = 78,
+	[2][1][6][7] = 40,
+	[2][1][9][7] = 40,
+	[2][1][8][7] = 48,
+	[2][1][11][7] = 40,
+	[2][1][2][8] = 74,
+	[2][1][1][8] = 40,
+	[2][1][3][8] = 52,
+	[2][1][5][8] = 74,
+	[2][1][6][8] = 40,
+	[2][1][9][8] = 40,
+	[2][1][8][8] = 48,
+	[2][1][11][8] = 40,
+	[2][1][2][9] = 70,
+	[2][1][1][9] = 40,
+	[2][1][3][9] = 52,
+	[2][1][5][9] = 70,
+	[2][1][6][9] = 40,
+	[2][1][9][9] = 40,
+	[2][1][8][9] = 48,
+	[2][1][11][9] = 40,
+	[2][1][2][10] = 70,
+	[2][1][1][10] = 40,
+	[2][1][3][10] = 52,
+	[2][1][5][10] = 70,
+	[2][1][6][10] = 40,
+	[2][1][9][10] = 40,
+	[2][1][8][10] = 48,
+	[2][1][11][10] = 40,
+	[2][1][2][11] = 48,
+	[2][1][1][11] = 40,
+	[2][1][3][11] = 52,
+	[2][1][5][11] = 48,
+	[2][1][6][11] = 40,
+	[2][1][9][11] = 40,
+	[2][1][8][11] = 48,
+	[2][1][11][11] = 40,
+	[2][1][2][12] = 26,
+	[2][1][1][12] = 40,
+	[2][1][3][12] = 52,
+	[2][1][5][12] = 26,
+	[2][1][6][12] = 40,
+	[2][1][9][12] = 40,
+	[2][1][8][12] = 48,
+	[2][1][11][12] = 40,
+	[2][1][2][13] = 127,
+	[2][1][1][13] = 127,
+	[2][1][3][13] = 127,
+	[2][1][5][13] = 127,
+	[2][1][6][13] = 127,
+	[2][1][9][13] = 127,
+	[2][1][8][13] = 127,
+	[2][1][11][13] = 127,
+};
+
+const s8 rtw89_8852a_txpwr_lmt_ru_5g[RTW89_RU_NUM][RTW89_NTX_NUM]
+				    [RTW89_REGD_NUM][RTW89_5G_CH_NUM] = {
+	[0][0][0][0] = 22,
+	[0][0][0][2] = 22,
+	[0][0][0][4] = 22,
+	[0][0][0][6] = 22,
+	[0][0][0][8] = 24,
+	[0][0][0][10] = 24,
+	[0][0][0][12] = 24,
+	[0][0][0][14] = 24,
+	[0][0][0][15] = 24,
+	[0][0][0][17] = 24,
+	[0][0][0][19] = 24,
+	[0][0][0][21] = 24,
+	[0][0][0][23] = 24,
+	[0][0][0][25] = 24,
+	[0][0][0][27] = 24,
+	[0][0][0][29] = 24,
+	[0][0][0][31] = 24,
+	[0][0][0][33] = 24,
+	[0][0][0][35] = 24,
+	[0][0][0][37] = 24,
+	[0][0][0][38] = 28,
+	[0][0][0][40] = 28,
+	[0][0][0][42] = 28,
+	[0][0][0][44] = 28,
+	[0][0][0][46] = 28,
+	[0][1][0][0] = 8,
+	[0][1][0][2] = 8,
+	[0][1][0][4] = 8,
+	[0][1][0][6] = 8,
+	[0][1][0][8] = 12,
+	[0][1][0][10] = 12,
+	[0][1][0][12] = 12,
+	[0][1][0][14] = 12,
+	[0][1][0][15] = 12,
+	[0][1][0][17] = 12,
+	[0][1][0][19] = 12,
+	[0][1][0][21] = 12,
+	[0][1][0][23] = 12,
+	[0][1][0][25] = 12,
+	[0][1][0][27] = 12,
+	[0][1][0][29] = 12,
+	[0][1][0][31] = 12,
+	[0][1][0][33] = 12,
+	[0][1][0][35] = 12,
+	[0][1][0][37] = 12,
+	[0][1][0][38] = 16,
+	[0][1][0][40] = 16,
+	[0][1][0][42] = 16,
+	[0][1][0][44] = 16,
+	[0][1][0][46] = 16,
+	[1][0][0][0] = 30,
+	[1][0][0][2] = 30,
+	[1][0][0][4] = 30,
+	[1][0][0][6] = 30,
+	[1][0][0][8] = 36,
+	[1][0][0][10] = 36,
+	[1][0][0][12] = 36,
+	[1][0][0][14] = 36,
+	[1][0][0][15] = 36,
+	[1][0][0][17] = 36,
+	[1][0][0][19] = 36,
+	[1][0][0][21] = 36,
+	[1][0][0][23] = 36,
+	[1][0][0][25] = 36,
+	[1][0][0][27] = 36,
+	[1][0][0][29] = 36,
+	[1][0][0][31] = 36,
+	[1][0][0][33] = 36,
+	[1][0][0][35] = 36,
+	[1][0][0][37] = 36,
+	[1][0][0][38] = 28,
+	[1][0][0][40] = 28,
+	[1][0][0][42] = 28,
+	[1][0][0][44] = 28,
+	[1][0][0][46] = 28,
+	[1][1][0][0] = 18,
+	[1][1][0][2] = 18,
+	[1][1][0][4] = 18,
+	[1][1][0][6] = 18,
+	[1][1][0][8] = 22,
+	[1][1][0][10] = 22,
+	[1][1][0][12] = 22,
+	[1][1][0][14] = 22,
+	[1][1][0][15] = 22,
+	[1][1][0][17] = 22,
+	[1][1][0][19] = 22,
+	[1][1][0][21] = 22,
+	[1][1][0][23] = 22,
+	[1][1][0][25] = 22,
+	[1][1][0][27] = 22,
+	[1][1][0][29] = 22,
+	[1][1][0][31] = 22,
+	[1][1][0][33] = 22,
+	[1][1][0][35] = 22,
+	[1][1][0][37] = 22,
+	[1][1][0][38] = 16,
+	[1][1][0][40] = 16,
+	[1][1][0][42] = 16,
+	[1][1][0][44] = 16,
+	[1][1][0][46] = 16,
+	[2][0][0][0] = 30,
+	[2][0][0][2] = 30,
+	[2][0][0][4] = 30,
+	[2][0][0][6] = 30,
+	[2][0][0][8] = 46,
+	[2][0][0][10] = 46,
+	[2][0][0][12] = 46,
+	[2][0][0][14] = 46,
+	[2][0][0][15] = 46,
+	[2][0][0][17] = 46,
+	[2][0][0][19] = 46,
+	[2][0][0][21] = 46,
+	[2][0][0][23] = 46,
+	[2][0][0][25] = 46,
+	[2][0][0][27] = 46,
+	[2][0][0][29] = 46,
+	[2][0][0][31] = 46,
+	[2][0][0][33] = 46,
+	[2][0][0][35] = 46,
+	[2][0][0][37] = 46,
+	[2][0][0][38] = 28,
+	[2][0][0][40] = 28,
+	[2][0][0][42] = 28,
+	[2][0][0][44] = 28,
+	[2][0][0][46] = 28,
+	[2][1][0][0] = 18,
+	[2][1][0][2] = 18,
+	[2][1][0][4] = 18,
+	[2][1][0][6] = 18,
+	[2][1][0][8] = 32,
+	[2][1][0][10] = 32,
+	[2][1][0][12] = 32,
+	[2][1][0][14] = 32,
+	[2][1][0][15] = 32,
+	[2][1][0][17] = 32,
+	[2][1][0][19] = 32,
+	[2][1][0][21] = 32,
+	[2][1][0][23] = 32,
+	[2][1][0][25] = 32,
+	[2][1][0][27] = 32,
+	[2][1][0][29] = 32,
+	[2][1][0][31] = 32,
+	[2][1][0][33] = 32,
+	[2][1][0][35] = 32,
+	[2][1][0][37] = 32,
+	[2][1][0][38] = 16,
+	[2][1][0][40] = 16,
+	[2][1][0][42] = 16,
+	[2][1][0][44] = 16,
+	[2][1][0][46] = 16,
+	[0][0][2][0] = 48,
+	[0][0][1][0] = 24,
+	[0][0][3][0] = 26,
+	[0][0][5][0] = 22,
+	[0][0][6][0] = 24,
+	[0][0][9][0] = 24,
+	[0][0][8][0] = 30,
+	[0][0][11][0] = 24,
+	[0][0][2][2] = 48,
+	[0][0][1][2] = 24,
+	[0][0][3][2] = 26,
+	[0][0][5][2] = 22,
+	[0][0][6][2] = 24,
+	[0][0][9][2] = 24,
+	[0][0][8][2] = 30,
+	[0][0][11][2] = 24,
+	[0][0][2][4] = 48,
+	[0][0][1][4] = 24,
+	[0][0][3][4] = 26,
+	[0][0][5][4] = 22,
+	[0][0][6][4] = 24,
+	[0][0][9][4] = 24,
+	[0][0][8][4] = 30,
+	[0][0][11][4] = 24,
+	[0][0][2][6] = 48,
+	[0][0][1][6] = 24,
+	[0][0][3][6] = 26,
+	[0][0][5][6] = 22,
+	[0][0][6][6] = 24,
+	[0][0][9][6] = 24,
+	[0][0][8][6] = 30,
+	[0][0][11][6] = 24,
+	[0][0][2][8] = 48,
+	[0][0][1][8] = 24,
+	[0][0][3][8] = 26,
+	[0][0][5][8] = 48,
+	[0][0][6][8] = 24,
+	[0][0][9][8] = 24,
+	[0][0][8][8] = 54,
+	[0][0][11][8] = 24,
+	[0][0][2][10] = 48,
+	[0][0][1][10] = 24,
+	[0][0][3][10] = 26,
+	[0][0][5][10] = 48,
+	[0][0][6][10] = 24,
+	[0][0][9][10] = 24,
+	[0][0][8][10] = 54,
+	[0][0][11][10] = 24,
+	[0][0][2][12] = 48,
+	[0][0][1][12] = 24,
+	[0][0][3][12] = 26,
+	[0][0][5][12] = 48,
+	[0][0][6][12] = 24,
+	[0][0][9][12] = 24,
+	[0][0][8][12] = 54,
+	[0][0][11][12] = 24,
+	[0][0][2][14] = 48,
+	[0][0][1][14] = 24,
+	[0][0][3][14] = 26,
+	[0][0][5][14] = 48,
+	[0][0][6][14] = 24,
+	[0][0][9][14] = 24,
+	[0][0][8][14] = 54,
+	[0][0][11][14] = 24,
+	[0][0][2][15] = 48,
+	[0][0][1][15] = 24,
+	[0][0][3][15] = 44,
+	[0][0][5][15] = 48,
+	[0][0][6][15] = 24,
+	[0][0][9][15] = 24,
+	[0][0][8][15] = 54,
+	[0][0][11][15] = 24,
+	[0][0][2][17] = 48,
+	[0][0][1][17] = 24,
+	[0][0][3][17] = 44,
+	[0][0][5][17] = 48,
+	[0][0][6][17] = 24,
+	[0][0][9][17] = 24,
+	[0][0][8][17] = 54,
+	[0][0][11][17] = 24,
+	[0][0][2][19] = 48,
+	[0][0][1][19] = 24,
+	[0][0][3][19] = 44,
+	[0][0][5][19] = 48,
+	[0][0][6][19] = 24,
+	[0][0][9][19] = 24,
+	[0][0][8][19] = 54,
+	[0][0][11][19] = 24,
+	[0][0][2][21] = 48,
+	[0][0][1][21] = 24,
+	[0][0][3][21] = 44,
+	[0][0][5][21] = 48,
+	[0][0][6][21] = 24,
+	[0][0][9][21] = 24,
+	[0][0][8][21] = 54,
+	[0][0][11][21] = 24,
+	[0][0][2][23] = 48,
+	[0][0][1][23] = 24,
+	[0][0][3][23] = 44,
+	[0][0][5][23] = 48,
+	[0][0][6][23] = 24,
+	[0][0][9][23] = 24,
+	[0][0][8][23] = 54,
+	[0][0][11][23] = 24,
+	[0][0][2][25] = 48,
+	[0][0][1][25] = 24,
+	[0][0][3][25] = 44,
+	[0][0][5][25] = 127,
+	[0][0][6][25] = 24,
+	[0][0][9][25] = 127,
+	[0][0][8][25] = 54,
+	[0][0][11][25] = 24,
+	[0][0][2][27] = 48,
+	[0][0][1][27] = 24,
+	[0][0][3][27] = 44,
+	[0][0][5][27] = 127,
+	[0][0][6][27] = 24,
+	[0][0][9][27] = 127,
+	[0][0][8][27] = 54,
+	[0][0][11][27] = 24,
+	[0][0][2][29] = 48,
+	[0][0][1][29] = 24,
+	[0][0][3][29] = 44,
+	[0][0][5][29] = 127,
+	[0][0][6][29] = 24,
+	[0][0][9][29] = 127,
+	[0][0][8][29] = 54,
+	[0][0][11][29] = 24,
+	[0][0][2][31] = 48,
+	[0][0][1][31] = 24,
+	[0][0][3][31] = 44,
+	[0][0][5][31] = 48,
+	[0][0][6][31] = 24,
+	[0][0][9][31] = 24,
+	[0][0][8][31] = 54,
+	[0][0][11][31] = 24,
+	[0][0][2][33] = 48,
+	[0][0][1][33] = 24,
+	[0][0][3][33] = 44,
+	[0][0][5][33] = 48,
+	[0][0][6][33] = 24,
+	[0][0][9][33] = 24,
+	[0][0][8][33] = 54,
+	[0][0][11][33] = 24,
+	[0][0][2][35] = 48,
+	[0][0][1][35] = 24,
+	[0][0][3][35] = 44,
+	[0][0][5][35] = 48,
+	[0][0][6][35] = 24,
+	[0][0][9][35] = 24,
+	[0][0][8][35] = 54,
+	[0][0][11][35] = 24,
+	[0][0][2][37] = 48,
+	[0][0][1][37] = 127,
+	[0][0][3][37] = 44,
+	[0][0][5][37] = 48,
+	[0][0][6][37] = 24,
+	[0][0][9][37] = 48,
+	[0][0][8][37] = 54,
+	[0][0][11][37] = 127,
+	[0][0][2][38] = 76,
+	[0][0][1][38] = 28,
+	[0][0][3][38] = 127,
+	[0][0][5][38] = 76,
+	[0][0][6][38] = 28,
+	[0][0][9][38] = 76,
+	[0][0][8][38] = 54,
+	[0][0][11][38] = 28,
+	[0][0][2][40] = 76,
+	[0][0][1][40] = 28,
+	[0][0][3][40] = 127,
+	[0][0][5][40] = 76,
+	[0][0][6][40] = 28,
+	[0][0][9][40] = 76,
+	[0][0][8][40] = 54,
+	[0][0][11][40] = 28,
+	[0][0][2][42] = 76,
+	[0][0][1][42] = 28,
+	[0][0][3][42] = 127,
+	[0][0][5][42] = 76,
+	[0][0][6][42] = 28,
+	[0][0][9][42] = 76,
+	[0][0][8][42] = 54,
+	[0][0][11][42] = 28,
+	[0][0][2][44] = 76,
+	[0][0][1][44] = 28,
+	[0][0][3][44] = 127,
+	[0][0][5][44] = 76,
+	[0][0][6][44] = 28,
+	[0][0][9][44] = 76,
+	[0][0][8][44] = 54,
+	[0][0][11][44] = 28,
+	[0][0][2][46] = 76,
+	[0][0][1][46] = 28,
+	[0][0][3][46] = 127,
+	[0][0][5][46] = 76,
+	[0][0][6][46] = 28,
+	[0][0][9][46] = 76,
+	[0][0][8][46] = 54,
+	[0][0][11][46] = 28,
+	[0][1][2][0] = 36,
+	[0][1][1][0] = 12,
+	[0][1][3][0] = 14,
+	[0][1][5][0] = 8,
+	[0][1][6][0] = 12,
+	[0][1][9][0] = 12,
+	[0][1][8][0] = 18,
+	[0][1][11][0] = 12,
+	[0][1][2][2] = 36,
+	[0][1][1][2] = 12,
+	[0][1][3][2] = 14,
+	[0][1][5][2] = 8,
+	[0][1][6][2] = 12,
+	[0][1][9][2] = 12,
+	[0][1][8][2] = 18,
+	[0][1][11][2] = 12,
+	[0][1][2][4] = 36,
+	[0][1][1][4] = 12,
+	[0][1][3][4] = 14,
+	[0][1][5][4] = 8,
+	[0][1][6][4] = 12,
+	[0][1][9][4] = 12,
+	[0][1][8][4] = 18,
+	[0][1][11][4] = 12,
+	[0][1][2][6] = 36,
+	[0][1][1][6] = 12,
+	[0][1][3][6] = 14,
+	[0][1][5][6] = 8,
+	[0][1][6][6] = 12,
+	[0][1][9][6] = 12,
+	[0][1][8][6] = 18,
+	[0][1][11][6] = 12,
+	[0][1][2][8] = 36,
+	[0][1][1][8] = 12,
+	[0][1][3][8] = 14,
+	[0][1][5][8] = 36,
+	[0][1][6][8] = 12,
+	[0][1][9][8] = 12,
+	[0][1][8][8] = 42,
+	[0][1][11][8] = 12,
+	[0][1][2][10] = 36,
+	[0][1][1][10] = 12,
+	[0][1][3][10] = 14,
+	[0][1][5][10] = 36,
+	[0][1][6][10] = 12,
+	[0][1][9][10] = 12,
+	[0][1][8][10] = 42,
+	[0][1][11][10] = 12,
+	[0][1][2][12] = 36,
+	[0][1][1][12] = 12,
+	[0][1][3][12] = 14,
+	[0][1][5][12] = 36,
+	[0][1][6][12] = 12,
+	[0][1][9][12] = 12,
+	[0][1][8][12] = 42,
+	[0][1][11][12] = 12,
+	[0][1][2][14] = 36,
+	[0][1][1][14] = 12,
+	[0][1][3][14] = 14,
+	[0][1][5][14] = 36,
+	[0][1][6][14] = 12,
+	[0][1][9][14] = 12,
+	[0][1][8][14] = 42,
+	[0][1][11][14] = 12,
+	[0][1][2][15] = 36,
+	[0][1][1][15] = 12,
+	[0][1][3][15] = 32,
+	[0][1][5][15] = 36,
+	[0][1][6][15] = 12,
+	[0][1][9][15] = 12,
+	[0][1][8][15] = 42,
+	[0][1][11][15] = 12,
+	[0][1][2][17] = 36,
+	[0][1][1][17] = 12,
+	[0][1][3][17] = 32,
+	[0][1][5][17] = 36,
+	[0][1][6][17] = 12,
+	[0][1][9][17] = 12,
+	[0][1][8][17] = 42,
+	[0][1][11][17] = 12,
+	[0][1][2][19] = 36,
+	[0][1][1][19] = 12,
+	[0][1][3][19] = 32,
+	[0][1][5][19] = 36,
+	[0][1][6][19] = 12,
+	[0][1][9][19] = 12,
+	[0][1][8][19] = 42,
+	[0][1][11][19] = 12,
+	[0][1][2][21] = 36,
+	[0][1][1][21] = 12,
+	[0][1][3][21] = 32,
+	[0][1][5][21] = 36,
+	[0][1][6][21] = 12,
+	[0][1][9][21] = 12,
+	[0][1][8][21] = 42,
+	[0][1][11][21] = 12,
+	[0][1][2][23] = 36,
+	[0][1][1][23] = 12,
+	[0][1][3][23] = 32,
+	[0][1][5][23] = 36,
+	[0][1][6][23] = 12,
+	[0][1][9][23] = 12,
+	[0][1][8][23] = 42,
+	[0][1][11][23] = 12,
+	[0][1][2][25] = 36,
+	[0][1][1][25] = 12,
+	[0][1][3][25] = 32,
+	[0][1][5][25] = 127,
+	[0][1][6][25] = 12,
+	[0][1][9][25] = 127,
+	[0][1][8][25] = 42,
+	[0][1][11][25] = 12,
+	[0][1][2][27] = 36,
+	[0][1][1][27] = 12,
+	[0][1][3][27] = 32,
+	[0][1][5][27] = 127,
+	[0][1][6][27] = 12,
+	[0][1][9][27] = 127,
+	[0][1][8][27] = 42,
+	[0][1][11][27] = 12,
+	[0][1][2][29] = 36,
+	[0][1][1][29] = 12,
+	[0][1][3][29] = 32,
+	[0][1][5][29] = 127,
+	[0][1][6][29] = 12,
+	[0][1][9][29] = 127,
+	[0][1][8][29] = 42,
+	[0][1][11][29] = 12,
+	[0][1][2][31] = 36,
+	[0][1][1][31] = 12,
+	[0][1][3][31] = 32,
+	[0][1][5][31] = 36,
+	[0][1][6][31] = 12,
+	[0][1][9][31] = 12,
+	[0][1][8][31] = 42,
+	[0][1][11][31] = 12,
+	[0][1][2][33] = 36,
+	[0][1][1][33] = 12,
+	[0][1][3][33] = 32,
+	[0][1][5][33] = 36,
+	[0][1][6][33] = 12,
+	[0][1][9][33] = 12,
+	[0][1][8][33] = 42,
+	[0][1][11][33] = 12,
+	[0][1][2][35] = 36,
+	[0][1][1][35] = 12,
+	[0][1][3][35] = 32,
+	[0][1][5][35] = 36,
+	[0][1][6][35] = 12,
+	[0][1][9][35] = 12,
+	[0][1][8][35] = 42,
+	[0][1][11][35] = 12,
+	[0][1][2][37] = 36,
+	[0][1][1][37] = 127,
+	[0][1][3][37] = 32,
+	[0][1][5][37] = 36,
+	[0][1][6][37] = 12,
+	[0][1][9][37] = 36,
+	[0][1][8][37] = 42,
+	[0][1][11][37] = 127,
+	[0][1][2][38] = 72,
+	[0][1][1][38] = 16,
+	[0][1][3][38] = 127,
+	[0][1][5][38] = 72,
+	[0][1][6][38] = 16,
+	[0][1][9][38] = 76,
+	[0][1][8][38] = 42,
+	[0][1][11][38] = 16,
+	[0][1][2][40] = 76,
+	[0][1][1][40] = 16,
+	[0][1][3][40] = 127,
+	[0][1][5][40] = 76,
+	[0][1][6][40] = 16,
+	[0][1][9][40] = 76,
+	[0][1][8][40] = 42,
+	[0][1][11][40] = 16,
+	[0][1][2][42] = 76,
+	[0][1][1][42] = 16,
+	[0][1][3][42] = 127,
+	[0][1][5][42] = 76,
+	[0][1][6][42] = 16,
+	[0][1][9][42] = 76,
+	[0][1][8][42] = 42,
+	[0][1][11][42] = 16,
+	[0][1][2][44] = 76,
+	[0][1][1][44] = 16,
+	[0][1][3][44] = 127,
+	[0][1][5][44] = 76,
+	[0][1][6][44] = 16,
+	[0][1][9][44] = 76,
+	[0][1][8][44] = 42,
+	[0][1][11][44] = 16,
+	[0][1][2][46] = 76,
+	[0][1][1][46] = 16,
+	[0][1][3][46] = 127,
+	[0][1][5][46] = 76,
+	[0][1][6][46] = 16,
+	[0][1][9][46] = 76,
+	[0][1][8][46] = 42,
+	[0][1][11][46] = 16,
+	[1][0][2][0] = 62,
+	[1][0][1][0] = 36,
+	[1][0][3][0] = 36,
+	[1][0][5][0] = 34,
+	[1][0][6][0] = 36,
+	[1][0][9][0] = 36,
+	[1][0][8][0] = 30,
+	[1][0][11][0] = 36,
+	[1][0][2][2] = 62,
+	[1][0][1][2] = 36,
+	[1][0][3][2] = 36,
+	[1][0][5][2] = 34,
+	[1][0][6][2] = 36,
+	[1][0][9][2] = 36,
+	[1][0][8][2] = 30,
+	[1][0][11][2] = 36,
+	[1][0][2][4] = 62,
+	[1][0][1][4] = 36,
+	[1][0][3][4] = 36,
+	[1][0][5][4] = 34,
+	[1][0][6][4] = 36,
+	[1][0][9][4] = 36,
+	[1][0][8][4] = 30,
+	[1][0][11][4] = 36,
+	[1][0][2][6] = 62,
+	[1][0][1][6] = 36,
+	[1][0][3][6] = 36,
+	[1][0][5][6] = 34,
+	[1][0][6][6] = 36,
+	[1][0][9][6] = 36,
+	[1][0][8][6] = 30,
+	[1][0][11][6] = 36,
+	[1][0][2][8] = 62,
+	[1][0][1][8] = 36,
+	[1][0][3][8] = 36,
+	[1][0][5][8] = 62,
+	[1][0][6][8] = 36,
+	[1][0][9][8] = 36,
+	[1][0][8][8] = 54,
+	[1][0][11][8] = 36,
+	[1][0][2][10] = 62,
+	[1][0][1][10] = 36,
+	[1][0][3][10] = 36,
+	[1][0][5][10] = 62,
+	[1][0][6][10] = 36,
+	[1][0][9][10] = 36,
+	[1][0][8][10] = 54,
+	[1][0][11][10] = 36,
+	[1][0][2][12] = 62,
+	[1][0][1][12] = 36,
+	[1][0][3][12] = 36,
+	[1][0][5][12] = 62,
+	[1][0][6][12] = 36,
+	[1][0][9][12] = 36,
+	[1][0][8][12] = 54,
+	[1][0][11][12] = 36,
+	[1][0][2][14] = 62,
+	[1][0][1][14] = 36,
+	[1][0][3][14] = 36,
+	[1][0][5][14] = 62,
+	[1][0][6][14] = 36,
+	[1][0][9][14] = 36,
+	[1][0][8][14] = 54,
+	[1][0][11][14] = 36,
+	[1][0][2][15] = 62,
+	[1][0][1][15] = 36,
+	[1][0][3][15] = 58,
+	[1][0][5][15] = 62,
+	[1][0][6][15] = 36,
+	[1][0][9][15] = 36,
+	[1][0][8][15] = 54,
+	[1][0][11][15] = 36,
+	[1][0][2][17] = 62,
+	[1][0][1][17] = 36,
+	[1][0][3][17] = 58,
+	[1][0][5][17] = 62,
+	[1][0][6][17] = 36,
+	[1][0][9][17] = 36,
+	[1][0][8][17] = 54,
+	[1][0][11][17] = 36,
+	[1][0][2][19] = 62,
+	[1][0][1][19] = 36,
+	[1][0][3][19] = 58,
+	[1][0][5][19] = 62,
+	[1][0][6][19] = 36,
+	[1][0][9][19] = 36,
+	[1][0][8][19] = 54,
+	[1][0][11][19] = 36,
+	[1][0][2][21] = 62,
+	[1][0][1][21] = 36,
+	[1][0][3][21] = 58,
+	[1][0][5][21] = 62,
+	[1][0][6][21] = 36,
+	[1][0][9][21] = 36,
+	[1][0][8][21] = 54,
+	[1][0][11][21] = 36,
+	[1][0][2][23] = 62,
+	[1][0][1][23] = 36,
+	[1][0][3][23] = 58,
+	[1][0][5][23] = 62,
+	[1][0][6][23] = 36,
+	[1][0][9][23] = 36,
+	[1][0][8][23] = 54,
+	[1][0][11][23] = 36,
+	[1][0][2][25] = 62,
+	[1][0][1][25] = 36,
+	[1][0][3][25] = 58,
+	[1][0][5][25] = 127,
+	[1][0][6][25] = 36,
+	[1][0][9][25] = 127,
+	[1][0][8][25] = 54,
+	[1][0][11][25] = 36,
+	[1][0][2][27] = 62,
+	[1][0][1][27] = 36,
+	[1][0][3][27] = 58,
+	[1][0][5][27] = 127,
+	[1][0][6][27] = 36,
+	[1][0][9][27] = 127,
+	[1][0][8][27] = 54,
+	[1][0][11][27] = 36,
+	[1][0][2][29] = 62,
+	[1][0][1][29] = 36,
+	[1][0][3][29] = 58,
+	[1][0][5][29] = 127,
+	[1][0][6][29] = 36,
+	[1][0][9][29] = 127,
+	[1][0][8][29] = 54,
+	[1][0][11][29] = 36,
+	[1][0][2][31] = 62,
+	[1][0][1][31] = 36,
+	[1][0][3][31] = 58,
+	[1][0][5][31] = 62,
+	[1][0][6][31] = 36,
+	[1][0][9][31] = 36,
+	[1][0][8][31] = 54,
+	[1][0][11][31] = 36,
+	[1][0][2][33] = 62,
+	[1][0][1][33] = 36,
+	[1][0][3][33] = 58,
+	[1][0][5][33] = 62,
+	[1][0][6][33] = 36,
+	[1][0][9][33] = 36,
+	[1][0][8][33] = 54,
+	[1][0][11][33] = 36,
+	[1][0][2][35] = 62,
+	[1][0][1][35] = 36,
+	[1][0][3][35] = 58,
+	[1][0][5][35] = 62,
+	[1][0][6][35] = 36,
+	[1][0][9][35] = 36,
+	[1][0][8][35] = 54,
+	[1][0][11][35] = 36,
+	[1][0][2][37] = 56,
+	[1][0][1][37] = 62,
+	[1][0][3][37] = 127,
+	[1][0][5][37] = 58,
+	[1][0][6][37] = 62,
+	[1][0][9][37] = 36,
+	[1][0][8][37] = 62,
+	[1][0][11][37] = 54,
+	[1][0][2][38] = 76,
+	[1][0][1][38] = 28,
+	[1][0][3][38] = 127,
+	[1][0][5][38] = 76,
+	[1][0][6][38] = 28,
+	[1][0][9][38] = 76,
+	[1][0][8][38] = 54,
+	[1][0][11][38] = 28,
+	[1][0][2][40] = 76,
+	[1][0][1][40] = 28,
+	[1][0][3][40] = 127,
+	[1][0][5][40] = 76,
+	[1][0][6][40] = 28,
+	[1][0][9][40] = 76,
+	[1][0][8][40] = 54,
+	[1][0][11][40] = 28,
+	[1][0][2][42] = 76,
+	[1][0][1][42] = 28,
+	[1][0][3][42] = 127,
+	[1][0][5][42] = 76,
+	[1][0][6][42] = 28,
+	[1][0][9][42] = 76,
+	[1][0][8][42] = 54,
+	[1][0][11][42] = 28,
+	[1][0][2][44] = 76,
+	[1][0][1][44] = 28,
+	[1][0][3][44] = 127,
+	[1][0][5][44] = 76,
+	[1][0][6][44] = 28,
+	[1][0][9][44] = 76,
+	[1][0][8][44] = 54,
+	[1][0][11][44] = 28,
+	[1][0][2][46] = 76,
+	[1][0][1][46] = 28,
+	[1][0][3][46] = 127,
+	[1][0][5][46] = 76,
+	[1][0][6][46] = 28,
+	[1][0][9][46] = 76,
+	[1][0][8][46] = 54,
+	[1][0][11][46] = 28,
+	[1][1][2][0] = 46,
+	[1][1][1][0] = 22,
+	[1][1][3][0] = 24,
+	[1][1][5][0] = 18,
+	[1][1][6][0] = 22,
+	[1][1][9][0] = 22,
+	[1][1][8][0] = 18,
+	[1][1][11][0] = 22,
+	[1][1][2][2] = 46,
+	[1][1][1][2] = 22,
+	[1][1][3][2] = 24,
+	[1][1][5][2] = 18,
+	[1][1][6][2] = 22,
+	[1][1][9][2] = 22,
+	[1][1][8][2] = 18,
+	[1][1][11][2] = 22,
+	[1][1][2][4] = 46,
+	[1][1][1][4] = 22,
+	[1][1][3][4] = 24,
+	[1][1][5][4] = 18,
+	[1][1][6][4] = 22,
+	[1][1][9][4] = 22,
+	[1][1][8][4] = 18,
+	[1][1][11][4] = 22,
+	[1][1][2][6] = 46,
+	[1][1][1][6] = 22,
+	[1][1][3][6] = 24,
+	[1][1][5][6] = 18,
+	[1][1][6][6] = 22,
+	[1][1][9][6] = 22,
+	[1][1][8][6] = 18,
+	[1][1][11][6] = 22,
+	[1][1][2][8] = 46,
+	[1][1][1][8] = 22,
+	[1][1][3][8] = 24,
+	[1][1][5][8] = 46,
+	[1][1][6][8] = 22,
+	[1][1][9][8] = 22,
+	[1][1][8][8] = 42,
+	[1][1][11][8] = 22,
+	[1][1][2][10] = 46,
+	[1][1][1][10] = 22,
+	[1][1][3][10] = 24,
+	[1][1][5][10] = 46,
+	[1][1][6][10] = 22,
+	[1][1][9][10] = 22,
+	[1][1][8][10] = 42,
+	[1][1][11][10] = 22,
+	[1][1][2][12] = 46,
+	[1][1][1][12] = 22,
+	[1][1][3][12] = 24,
+	[1][1][5][12] = 46,
+	[1][1][6][12] = 22,
+	[1][1][9][12] = 22,
+	[1][1][8][12] = 42,
+	[1][1][11][12] = 22,
+	[1][1][2][14] = 46,
+	[1][1][1][14] = 22,
+	[1][1][3][14] = 24,
+	[1][1][5][14] = 46,
+	[1][1][6][14] = 22,
+	[1][1][9][14] = 22,
+	[1][1][8][14] = 42,
+	[1][1][11][14] = 22,
+	[1][1][2][15] = 46,
+	[1][1][1][15] = 22,
+	[1][1][3][15] = 46,
+	[1][1][5][15] = 46,
+	[1][1][6][15] = 22,
+	[1][1][9][15] = 22,
+	[1][1][8][15] = 42,
+	[1][1][11][15] = 22,
+	[1][1][2][17] = 46,
+	[1][1][1][17] = 22,
+	[1][1][3][17] = 46,
+	[1][1][5][17] = 46,
+	[1][1][6][17] = 22,
+	[1][1][9][17] = 22,
+	[1][1][8][17] = 42,
+	[1][1][11][17] = 22,
+	[1][1][2][19] = 46,
+	[1][1][1][19] = 22,
+	[1][1][3][19] = 46,
+	[1][1][5][19] = 46,
+	[1][1][6][19] = 22,
+	[1][1][9][19] = 22,
+	[1][1][8][19] = 42,
+	[1][1][11][19] = 22,
+	[1][1][2][21] = 46,
+	[1][1][1][21] = 22,
+	[1][1][3][21] = 46,
+	[1][1][5][21] = 46,
+	[1][1][6][21] = 22,
+	[1][1][9][21] = 22,
+	[1][1][8][21] = 42,
+	[1][1][11][21] = 22,
+	[1][1][2][23] = 46,
+	[1][1][1][23] = 22,
+	[1][1][3][23] = 46,
+	[1][1][5][23] = 46,
+	[1][1][6][23] = 22,
+	[1][1][9][23] = 22,
+	[1][1][8][23] = 42,
+	[1][1][11][23] = 22,
+	[1][1][2][25] = 46,
+	[1][1][1][25] = 22,
+	[1][1][3][25] = 46,
+	[1][1][5][25] = 127,
+	[1][1][6][25] = 22,
+	[1][1][9][25] = 127,
+	[1][1][8][25] = 42,
+	[1][1][11][25] = 22,
+	[1][1][2][27] = 46,
+	[1][1][1][27] = 22,
+	[1][1][3][27] = 46,
+	[1][1][5][27] = 127,
+	[1][1][6][27] = 22,
+	[1][1][9][27] = 127,
+	[1][1][8][27] = 42,
+	[1][1][11][27] = 22,
+	[1][1][2][29] = 46,
+	[1][1][1][29] = 22,
+	[1][1][3][29] = 46,
+	[1][1][5][29] = 127,
+	[1][1][6][29] = 22,
+	[1][1][9][29] = 127,
+	[1][1][8][29] = 42,
+	[1][1][11][29] = 22,
+	[1][1][2][31] = 46,
+	[1][1][1][31] = 22,
+	[1][1][3][31] = 46,
+	[1][1][5][31] = 46,
+	[1][1][6][31] = 22,
+	[1][1][9][31] = 22,
+	[1][1][8][31] = 42,
+	[1][1][11][31] = 22,
+	[1][1][2][33] = 46,
+	[1][1][1][33] = 22,
+	[1][1][3][33] = 46,
+	[1][1][5][33] = 46,
+	[1][1][6][33] = 22,
+	[1][1][9][33] = 22,
+	[1][1][8][33] = 42,
+	[1][1][11][33] = 22,
+	[1][1][2][35] = 46,
+	[1][1][1][35] = 22,
+	[1][1][3][35] = 46,
+	[1][1][5][35] = 46,
+	[1][1][6][35] = 22,
+	[1][1][9][35] = 22,
+	[1][1][8][35] = 42,
+	[1][1][11][35] = 22,
+	[1][1][2][37] = 46,
+	[1][1][1][37] = 127,
+	[1][1][3][37] = 46,
+	[1][1][5][37] = 46,
+	[1][1][6][37] = 22,
+	[1][1][9][37] = 50,
+	[1][1][8][37] = 42,
+	[1][1][11][37] = 127,
+	[1][1][2][38] = 74,
+	[1][1][1][38] = 16,
+	[1][1][3][38] = 127,
+	[1][1][5][38] = 74,
+	[1][1][6][38] = 16,
+	[1][1][9][38] = 76,
+	[1][1][8][38] = 42,
+	[1][1][11][38] = 16,
+	[1][1][2][40] = 76,
+	[1][1][1][40] = 16,
+	[1][1][3][40] = 127,
+	[1][1][5][40] = 76,
+	[1][1][6][40] = 16,
+	[1][1][9][40] = 76,
+	[1][1][8][40] = 42,
+	[1][1][11][40] = 16,
+	[1][1][2][42] = 76,
+	[1][1][1][42] = 16,
+	[1][1][3][42] = 127,
+	[1][1][5][42] = 76,
+	[1][1][6][42] = 16,
+	[1][1][9][42] = 76,
+	[1][1][8][42] = 42,
+	[1][1][11][42] = 16,
+	[1][1][2][44] = 76,
+	[1][1][1][44] = 16,
+	[1][1][3][44] = 127,
+	[1][1][5][44] = 76,
+	[1][1][6][44] = 16,
+	[1][1][9][44] = 76,
+	[1][1][8][44] = 42,
+	[1][1][11][44] = 16,
+	[1][1][2][46] = 76,
+	[1][1][1][46] = 16,
+	[1][1][3][46] = 127,
+	[1][1][5][46] = 76,
+	[1][1][6][46] = 16,
+	[1][1][9][46] = 76,
+	[1][1][8][46] = 42,
+	[1][1][11][46] = 16,
+	[2][0][2][0] = 74,
+	[2][0][1][0] = 46,
+	[2][0][3][0] = 50,
+	[2][0][5][0] = 46,
+	[2][0][6][0] = 46,
+	[2][0][9][0] = 46,
+	[2][0][8][0] = 30,
+	[2][0][11][0] = 46,
+	[2][0][2][2] = 74,
+	[2][0][1][2] = 46,
+	[2][0][3][2] = 50,
+	[2][0][5][2] = 46,
+	[2][0][6][2] = 46,
+	[2][0][9][2] = 46,
+	[2][0][8][2] = 30,
+	[2][0][11][2] = 46,
+	[2][0][2][4] = 74,
+	[2][0][1][4] = 46,
+	[2][0][3][4] = 50,
+	[2][0][5][4] = 46,
+	[2][0][6][4] = 46,
+	[2][0][9][4] = 46,
+	[2][0][8][4] = 30,
+	[2][0][11][4] = 46,
+	[2][0][2][6] = 74,
+	[2][0][1][6] = 46,
+	[2][0][3][6] = 50,
+	[2][0][5][6] = 46,
+	[2][0][6][6] = 46,
+	[2][0][9][6] = 46,
+	[2][0][8][6] = 30,
+	[2][0][11][6] = 46,
+	[2][0][2][8] = 74,
+	[2][0][1][8] = 46,
+	[2][0][3][8] = 50,
+	[2][0][5][8] = 66,
+	[2][0][6][8] = 46,
+	[2][0][9][8] = 46,
+	[2][0][8][8] = 54,
+	[2][0][11][8] = 46,
+	[2][0][2][10] = 74,
+	[2][0][1][10] = 46,
+	[2][0][3][10] = 50,
+	[2][0][5][10] = 66,
+	[2][0][6][10] = 46,
+	[2][0][9][10] = 46,
+	[2][0][8][10] = 54,
+	[2][0][11][10] = 46,
+	[2][0][2][12] = 74,
+	[2][0][1][12] = 46,
+	[2][0][3][12] = 50,
+	[2][0][5][12] = 66,
+	[2][0][6][12] = 46,
+	[2][0][9][12] = 46,
+	[2][0][8][12] = 54,
+	[2][0][11][12] = 46,
+	[2][0][2][14] = 74,
+	[2][0][1][14] = 46,
+	[2][0][3][14] = 50,
+	[2][0][5][14] = 66,
+	[2][0][6][14] = 46,
+	[2][0][9][14] = 46,
+	[2][0][8][14] = 54,
+	[2][0][11][14] = 46,
+	[2][0][2][15] = 74,
+	[2][0][1][15] = 46,
+	[2][0][3][15] = 70,
+	[2][0][5][15] = 74,
+	[2][0][6][15] = 46,
+	[2][0][9][15] = 46,
+	[2][0][8][15] = 54,
+	[2][0][11][15] = 46,
+	[2][0][2][17] = 74,
+	[2][0][1][17] = 46,
+	[2][0][3][17] = 70,
+	[2][0][5][17] = 74,
+	[2][0][6][17] = 46,
+	[2][0][9][17] = 46,
+	[2][0][8][17] = 54,
+	[2][0][11][17] = 46,
+	[2][0][2][19] = 74,
+	[2][0][1][19] = 46,
+	[2][0][3][19] = 70,
+	[2][0][5][19] = 74,
+	[2][0][6][19] = 46,
+	[2][0][9][19] = 46,
+	[2][0][8][19] = 54,
+	[2][0][11][19] = 46,
+	[2][0][2][21] = 74,
+	[2][0][1][21] = 46,
+	[2][0][3][21] = 70,
+	[2][0][5][21] = 74,
+	[2][0][6][21] = 46,
+	[2][0][9][21] = 46,
+	[2][0][8][21] = 54,
+	[2][0][11][21] = 46,
+	[2][0][2][23] = 74,
+	[2][0][1][23] = 46,
+	[2][0][3][23] = 70,
+	[2][0][5][23] = 74,
+	[2][0][6][23] = 46,
+	[2][0][9][23] = 46,
+	[2][0][8][23] = 54,
+	[2][0][11][23] = 46,
+	[2][0][2][25] = 74,
+	[2][0][1][25] = 46,
+	[2][0][3][25] = 70,
+	[2][0][5][25] = 127,
+	[2][0][6][25] = 46,
+	[2][0][9][25] = 127,
+	[2][0][8][25] = 54,
+	[2][0][11][25] = 46,
+	[2][0][2][27] = 74,
+	[2][0][1][27] = 46,
+	[2][0][3][27] = 70,
+	[2][0][5][27] = 127,
+	[2][0][6][27] = 46,
+	[2][0][9][27] = 127,
+	[2][0][8][27] = 54,
+	[2][0][11][27] = 46,
+	[2][0][2][29] = 74,
+	[2][0][1][29] = 46,
+	[2][0][3][29] = 70,
+	[2][0][5][29] = 127,
+	[2][0][6][29] = 46,
+	[2][0][9][29] = 127,
+	[2][0][8][29] = 54,
+	[2][0][11][29] = 46,
+	[2][0][2][31] = 74,
+	[2][0][1][31] = 46,
+	[2][0][3][31] = 70,
+	[2][0][5][31] = 74,
+	[2][0][6][31] = 46,
+	[2][0][9][31] = 46,
+	[2][0][8][31] = 54,
+	[2][0][11][31] = 46,
+	[2][0][2][33] = 74,
+	[2][0][1][33] = 46,
+	[2][0][3][33] = 70,
+	[2][0][5][33] = 74,
+	[2][0][6][33] = 46,
+	[2][0][9][33] = 46,
+	[2][0][8][33] = 54,
+	[2][0][11][33] = 46,
+	[2][0][2][35] = 74,
+	[2][0][1][35] = 46,
+	[2][0][3][35] = 70,
+	[2][0][5][35] = 74,
+	[2][0][6][35] = 46,
+	[2][0][9][35] = 46,
+	[2][0][8][35] = 54,
+	[2][0][11][35] = 46,
+	[2][0][2][37] = 74,
+	[2][0][1][37] = 127,
+	[2][0][3][37] = 70,
+	[2][0][5][37] = 74,
+	[2][0][6][37] = 46,
+	[2][0][9][37] = 74,
+	[2][0][8][37] = 54,
+	[2][0][11][37] = 127,
+	[2][0][2][38] = 76,
+	[2][0][1][38] = 28,
+	[2][0][3][38] = 127,
+	[2][0][5][38] = 76,
+	[2][0][6][38] = 28,
+	[2][0][9][38] = 76,
+	[2][0][8][38] = 54,
+	[2][0][11][38] = 28,
+	[2][0][2][40] = 76,
+	[2][0][1][40] = 28,
+	[2][0][3][40] = 127,
+	[2][0][5][40] = 76,
+	[2][0][6][40] = 28,
+	[2][0][9][40] = 76,
+	[2][0][8][40] = 54,
+	[2][0][11][40] = 28,
+	[2][0][2][42] = 76,
+	[2][0][1][42] = 28,
+	[2][0][3][42] = 127,
+	[2][0][5][42] = 76,
+	[2][0][6][42] = 28,
+	[2][0][9][42] = 76,
+	[2][0][8][42] = 54,
+	[2][0][11][42] = 28,
+	[2][0][2][44] = 76,
+	[2][0][1][44] = 28,
+	[2][0][3][44] = 127,
+	[2][0][5][44] = 76,
+	[2][0][6][44] = 28,
+	[2][0][9][44] = 76,
+	[2][0][8][44] = 54,
+	[2][0][11][44] = 28,
+	[2][0][2][46] = 76,
+	[2][0][1][46] = 28,
+	[2][0][3][46] = 127,
+	[2][0][5][46] = 76,
+	[2][0][6][46] = 28,
+	[2][0][9][46] = 76,
+	[2][0][8][46] = 54,
+	[2][0][11][46] = 28,
+	[2][1][2][0] = 58,
+	[2][1][1][0] = 32,
+	[2][1][3][0] = 38,
+	[2][1][5][0] = 30,
+	[2][1][6][0] = 32,
+	[2][1][9][0] = 32,
+	[2][1][8][0] = 18,
+	[2][1][11][0] = 32,
+	[2][1][2][2] = 58,
+	[2][1][1][2] = 32,
+	[2][1][3][2] = 38,
+	[2][1][5][2] = 30,
+	[2][1][6][2] = 32,
+	[2][1][9][2] = 32,
+	[2][1][8][2] = 18,
+	[2][1][11][2] = 32,
+	[2][1][2][4] = 58,
+	[2][1][1][4] = 32,
+	[2][1][3][4] = 38,
+	[2][1][5][4] = 30,
+	[2][1][6][4] = 32,
+	[2][1][9][4] = 32,
+	[2][1][8][4] = 18,
+	[2][1][11][4] = 32,
+	[2][1][2][6] = 58,
+	[2][1][1][6] = 32,
+	[2][1][3][6] = 38,
+	[2][1][5][6] = 30,
+	[2][1][6][6] = 32,
+	[2][1][9][6] = 32,
+	[2][1][8][6] = 18,
+	[2][1][11][6] = 32,
+	[2][1][2][8] = 58,
+	[2][1][1][8] = 32,
+	[2][1][3][8] = 38,
+	[2][1][5][8] = 52,
+	[2][1][6][8] = 32,
+	[2][1][9][8] = 32,
+	[2][1][8][8] = 42,
+	[2][1][11][8] = 32,
+	[2][1][2][10] = 58,
+	[2][1][1][10] = 32,
+	[2][1][3][10] = 38,
+	[2][1][5][10] = 52,
+	[2][1][6][10] = 32,
+	[2][1][9][10] = 32,
+	[2][1][8][10] = 42,
+	[2][1][11][10] = 32,
+	[2][1][2][12] = 58,
+	[2][1][1][12] = 32,
+	[2][1][3][12] = 38,
+	[2][1][5][12] = 52,
+	[2][1][6][12] = 32,
+	[2][1][9][12] = 32,
+	[2][1][8][12] = 42,
+	[2][1][11][12] = 32,
+	[2][1][2][14] = 58,
+	[2][1][1][14] = 32,
+	[2][1][3][14] = 38,
+	[2][1][5][14] = 52,
+	[2][1][6][14] = 32,
+	[2][1][9][14] = 32,
+	[2][1][8][14] = 42,
+	[2][1][11][14] = 32,
+	[2][1][2][15] = 58,
+	[2][1][1][15] = 32,
+	[2][1][3][15] = 58,
+	[2][1][5][15] = 58,
+	[2][1][6][15] = 32,
+	[2][1][9][15] = 32,
+	[2][1][8][15] = 42,
+	[2][1][11][15] = 32,
+	[2][1][2][17] = 58,
+	[2][1][1][17] = 32,
+	[2][1][3][17] = 58,
+	[2][1][5][17] = 58,
+	[2][1][6][17] = 32,
+	[2][1][9][17] = 32,
+	[2][1][8][17] = 42,
+	[2][1][11][17] = 32,
+	[2][1][2][19] = 58,
+	[2][1][1][19] = 32,
+	[2][1][3][19] = 58,
+	[2][1][5][19] = 58,
+	[2][1][6][19] = 32,
+	[2][1][9][19] = 32,
+	[2][1][8][19] = 42,
+	[2][1][11][19] = 32,
+	[2][1][2][21] = 58,
+	[2][1][1][21] = 32,
+	[2][1][3][21] = 58,
+	[2][1][5][21] = 58,
+	[2][1][6][21] = 32,
+	[2][1][9][21] = 32,
+	[2][1][8][21] = 42,
+	[2][1][11][21] = 32,
+	[2][1][2][23] = 58,
+	[2][1][1][23] = 32,
+	[2][1][3][23] = 58,
+	[2][1][5][23] = 58,
+	[2][1][6][23] = 32,
+	[2][1][9][23] = 32,
+	[2][1][8][23] = 42,
+	[2][1][11][23] = 32,
+	[2][1][2][25] = 58,
+	[2][1][1][25] = 32,
+	[2][1][3][25] = 58,
+	[2][1][5][25] = 127,
+	[2][1][6][25] = 32,
+	[2][1][9][25] = 127,
+	[2][1][8][25] = 42,
+	[2][1][11][25] = 32,
+	[2][1][2][27] = 58,
+	[2][1][1][27] = 32,
+	[2][1][3][27] = 58,
+	[2][1][5][27] = 127,
+	[2][1][6][27] = 32,
+	[2][1][9][27] = 127,
+	[2][1][8][27] = 42,
+	[2][1][11][27] = 32,
+	[2][1][2][29] = 58,
+	[2][1][1][29] = 32,
+	[2][1][3][29] = 58,
+	[2][1][5][29] = 127,
+	[2][1][6][29] = 32,
+	[2][1][9][29] = 127,
+	[2][1][8][29] = 42,
+	[2][1][11][29] = 32,
+	[2][1][2][31] = 58,
+	[2][1][1][31] = 32,
+	[2][1][3][31] = 58,
+	[2][1][5][31] = 58,
+	[2][1][6][31] = 32,
+	[2][1][9][31] = 32,
+	[2][1][8][31] = 42,
+	[2][1][11][31] = 32,
+	[2][1][2][33] = 58,
+	[2][1][1][33] = 32,
+	[2][1][3][33] = 58,
+	[2][1][5][33] = 58,
+	[2][1][6][33] = 32,
+	[2][1][9][33] = 32,
+	[2][1][8][33] = 42,
+	[2][1][11][33] = 32,
+	[2][1][2][35] = 58,
+	[2][1][1][35] = 32,
+	[2][1][3][35] = 58,
+	[2][1][5][35] = 58,
+	[2][1][6][35] = 32,
+	[2][1][9][35] = 32,
+	[2][1][8][35] = 42,
+	[2][1][11][35] = 32,
+	[2][1][2][37] = 58,
+	[2][1][1][37] = 127,
+	[2][1][3][37] = 58,
+	[2][1][5][37] = 58,
+	[2][1][6][37] = 32,
+	[2][1][9][37] = 62,
+	[2][1][8][37] = 42,
+	[2][1][11][37] = 127,
+	[2][1][2][38] = 76,
+	[2][1][1][38] = 16,
+	[2][1][3][38] = 127,
+	[2][1][5][38] = 76,
+	[2][1][6][38] = 16,
+	[2][1][9][38] = 76,
+	[2][1][8][38] = 42,
+	[2][1][11][38] = 16,
+	[2][1][2][40] = 76,
+	[2][1][1][40] = 16,
+	[2][1][3][40] = 127,
+	[2][1][5][40] = 76,
+	[2][1][6][40] = 16,
+	[2][1][9][40] = 76,
+	[2][1][8][40] = 42,
+	[2][1][11][40] = 16,
+	[2][1][2][42] = 76,
+	[2][1][1][42] = 16,
+	[2][1][3][42] = 127,
+	[2][1][5][42] = 76,
+	[2][1][6][42] = 16,
+	[2][1][9][42] = 76,
+	[2][1][8][42] = 42,
+	[2][1][11][42] = 16,
+	[2][1][2][44] = 76,
+	[2][1][1][44] = 16,
+	[2][1][3][44] = 127,
+	[2][1][5][44] = 76,
+	[2][1][6][44] = 16,
+	[2][1][9][44] = 76,
+	[2][1][8][44] = 42,
+	[2][1][11][44] = 16,
+	[2][1][2][46] = 76,
+	[2][1][1][46] = 16,
+	[2][1][3][46] = 127,
+	[2][1][5][46] = 76,
+	[2][1][6][46] = 16,
+	[2][1][9][46] = 76,
+	[2][1][8][46] = 42,
+	[2][1][11][46] = 16,
+};
+
+#define DECLARE_DIG_TABLE(name) \
+static const struct rtw89_phy_dig_gain_cfg name##_table = { \
+	.table = name, \
+	.size = ARRAY_SIZE(name) \
+}
+
+static const struct rtw89_reg_def rtw89_8852a_lna_gain_g[] = {
+	{R_PATH0_LNA_ERR1, B_PATH0_LNA_ERR_G0_G_MSK},
+	{R_PATH0_LNA_ERR2, B_PATH0_LNA_ERR_G1_G_MSK},
+	{R_PATH0_LNA_ERR2, B_PATH0_LNA_ERR_G2_G_MSK},
+	{R_PATH0_LNA_ERR3, B_PATH0_LNA_ERR_G3_G_MSK},
+	{R_PATH0_LNA_ERR3, B_PATH0_LNA_ERR_G4_G_MSK},
+	{R_PATH0_LNA_ERR4, B_PATH0_LNA_ERR_G5_G_MSK},
+	{R_PATH0_LNA_ERR5, B_PATH0_LNA_ERR_G6_G_MSK},
+};
+
+DECLARE_DIG_TABLE(rtw89_8852a_lna_gain_g);
+
+static const struct rtw89_reg_def rtw89_8852a_tia_gain_g[] = {
+	{R_PATH0_TIA_ERR_G0, B_PATH0_TIA_ERR_G0_G_MSK},
+	{R_PATH0_TIA_ERR_G1, B_PATH0_TIA_ERR_G1_G_MSK},
+};
+
+DECLARE_DIG_TABLE(rtw89_8852a_tia_gain_g);
+
+static const struct rtw89_reg_def rtw89_8852a_lna_gain_a[] = {
+	{R_PATH0_LNA_ERR1, B_PATH0_LNA_ERR_G0_A_MSK},
+	{R_PATH0_LNA_ERR1, B_PATH0_LNA_ERR_G1_A_MSK},
+	{R_PATH0_LNA_ERR2, B_PATH0_LNA_ERR_G2_A_MSK},
+	{R_PATH0_LNA_ERR3, B_PATH0_LNA_ERR_G3_A_MSK},
+	{R_PATH0_LNA_ERR3, B_PATH0_LNA_ERR_G4_A_MSK},
+	{R_PATH0_LNA_ERR4, B_PATH0_LNA_ERR_G5_A_MSK},
+	{R_PATH0_LNA_ERR4, B_PATH0_LNA_ERR_G6_A_MSK},
+};
+
+DECLARE_DIG_TABLE(rtw89_8852a_lna_gain_a);
+
+static const struct rtw89_reg_def rtw89_8852a_tia_gain_a[] = {
+	{R_PATH0_TIA_ERR_G0, B_PATH0_TIA_ERR_G0_A_MSK},
+	{R_PATH0_TIA_ERR_G1, B_PATH0_TIA_ERR_G1_A_MSK},
+};
+
+DECLARE_DIG_TABLE(rtw89_8852a_tia_gain_a);
+
+const struct rtw89_phy_table rtw89_8852a_phy_bb_table = {
+	.regs		= rtw89_8852a_phy_bb_regs,
+	.n_regs		= ARRAY_SIZE(rtw89_8852a_phy_bb_regs),
+	.rf_path	= 0, /* don't care */
+};
+
+const struct rtw89_phy_table rtw89_8852a_phy_radioa_table = {
+	.regs		= rtw89_8852a_phy_radioa_regs,
+	.n_regs		= ARRAY_SIZE(rtw89_8852a_phy_radioa_regs),
+	.rf_path	= RF_PATH_A,
+};
+
+const struct rtw89_phy_table rtw89_8852a_phy_radiob_table = {
+	.regs		= rtw89_8852a_phy_radiob_regs,
+	.n_regs		= ARRAY_SIZE(rtw89_8852a_phy_radiob_regs),
+	.rf_path	= RF_PATH_B,
+};
+
+const struct rtw89_phy_table rtw89_8852a_phy_nctl_table = {
+	.regs		= rtw89_8852a_phy_nctl_regs,
+	.n_regs		= ARRAY_SIZE(rtw89_8852a_phy_nctl_regs),
+	.rf_path	= 0, /* don't care */
+};
+
+const struct rtw89_txpwr_table rtw89_8852a_byr_table = {
+	.data = rtw89_8852a_txpwr_byrate,
+	.size = ARRAY_SIZE(rtw89_8852a_txpwr_byrate),
+	.load = rtw89_phy_load_txpwr_byrate,
+};
+
+const struct rtw89_txpwr_track_cfg rtw89_8852a_trk_cfg = {
+	.delta_swingidx_5gb_n = _txpwr_track_delta_swingidx_5gb_n,
+	.delta_swingidx_5gb_p = _txpwr_track_delta_swingidx_5gb_p,
+	.delta_swingidx_5ga_n = _txpwr_track_delta_swingidx_5ga_n,
+	.delta_swingidx_5ga_p = _txpwr_track_delta_swingidx_5ga_p,
+	.delta_swingidx_2gb_n = _txpwr_track_delta_swingidx_2gb_n,
+	.delta_swingidx_2gb_p = _txpwr_track_delta_swingidx_2gb_p,
+	.delta_swingidx_2ga_n = _txpwr_track_delta_swingidx_2ga_n,
+	.delta_swingidx_2ga_p = _txpwr_track_delta_swingidx_2ga_p,
+	.delta_swingidx_2g_cck_b_n = _txpwr_track_delta_swingidx_2g_cck_b_n,
+	.delta_swingidx_2g_cck_b_p = _txpwr_track_delta_swingidx_2g_cck_b_p,
+	.delta_swingidx_2g_cck_a_n = _txpwr_track_delta_swingidx_2g_cck_a_n,
+	.delta_swingidx_2g_cck_a_p = _txpwr_track_delta_swingidx_2g_cck_a_p,
+};
+
+const struct rtw89_phy_dig_gain_table rtw89_8852a_phy_dig_table = {
+	.cfg_lna_g = &rtw89_8852a_lna_gain_g_table,
+	.cfg_tia_g = &rtw89_8852a_tia_gain_g_table,
+	.cfg_lna_a = &rtw89_8852a_lna_gain_a_table,
+	.cfg_tia_a = &rtw89_8852a_tia_gain_a_table
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/rtw8852a_table.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/rtw8852a_table.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_8852A_TABLE_H__
+#define __RTW89_8852A_TABLE_H__
+
+#include "core.h"
+
+extern const struct rtw89_phy_table rtw89_8852a_phy_bb_table;
+extern const struct rtw89_phy_table rtw89_8852a_phy_radioa_table;
+extern const struct rtw89_phy_table rtw89_8852a_phy_radiob_table;
+extern const struct rtw89_phy_table rtw89_8852a_phy_nctl_table;
+extern const struct rtw89_txpwr_table rtw89_8852a_byr_table;
+extern const struct rtw89_phy_dig_gain_table rtw89_8852a_phy_dig_table;
+extern const struct rtw89_txpwr_track_cfg rtw89_8852a_trk_cfg;
+extern const s8 rtw89_8852a_txpwr_lmt_2g[RTW89_2G_BW_NUM][RTW89_NTX_NUM]
+					[RTW89_RS_LMT_NUM][RTW89_BF_NUM]
+					[RTW89_REGD_NUM][RTW89_2G_CH_NUM];
+extern const s8 rtw89_8852a_txpwr_lmt_5g[RTW89_5G_BW_NUM][RTW89_NTX_NUM]
+					[RTW89_RS_LMT_NUM][RTW89_BF_NUM]
+					[RTW89_REGD_NUM][RTW89_5G_CH_NUM];
+extern const s8 rtw89_8852a_txpwr_lmt_ru_2g[RTW89_RU_NUM][RTW89_NTX_NUM]
+					   [RTW89_REGD_NUM][RTW89_2G_CH_NUM];
+extern const s8 rtw89_8852a_txpwr_lmt_ru_5g[RTW89_RU_NUM][RTW89_NTX_NUM]
+					   [RTW89_REGD_NUM][RTW89_5G_CH_NUM];
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/sar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/sar.c
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "debug.h"
+#include "sar.h"
+
+static int rtw89_query_sar_config_common(struct rtw89_dev *rtwdev, s32 *cfg)
+{
+	struct rtw89_sar_cfg_common *rtwsar = &rtwdev->sar.cfg_common;
+	enum rtw89_subband subband = rtwdev->hal.current_subband;
+
+	if (!rtwsar->set[subband])
+		return -ENODATA;
+
+	*cfg = rtwsar->cfg[subband];
+	return 0;
+}
+
+static const
+struct rtw89_sar_handler rtw89_sar_handlers[RTW89_SAR_SOURCE_NR] = {
+	[RTW89_SAR_SOURCE_COMMON] = {
+		.descr_sar_source = "RTW89_SAR_SOURCE_COMMON",
+		.txpwr_factor_sar = 2,
+		.query_sar_config = rtw89_query_sar_config_common,
+	},
+};
+
+#define rtw89_sar_set_src(_dev, _src, _cfg_name, _cfg_data)		\
+	do {								\
+		typeof(_src) _s = (_src);				\
+		typeof(_dev) _d = (_dev);				\
+		BUILD_BUG_ON(!rtw89_sar_handlers[_s].descr_sar_source);	\
+		BUILD_BUG_ON(!rtw89_sar_handlers[_s].query_sar_config);	\
+		lockdep_assert_held(&_d->mutex);			\
+		_d->sar._cfg_name = *(_cfg_data);			\
+		_d->sar.src = _s;					\
+	} while (0)
+
+static s8 rtw89_txpwr_sar_to_mac(struct rtw89_dev *rtwdev, u8 fct, s32 cfg)
+{
+	const u8 fct_mac = rtwdev->chip->txpwr_factor_mac;
+	s32 cfg_mac;
+
+	cfg_mac = fct > fct_mac ?
+		  cfg >> (fct - fct_mac) : cfg << (fct_mac - fct);
+
+	return (s8)clamp_t(s32, cfg_mac,
+			   RTW89_SAR_TXPWR_MAC_MIN,
+			   RTW89_SAR_TXPWR_MAC_MAX);
+}
+
+s8 rtw89_query_sar(struct rtw89_dev *rtwdev)
+{
+	const enum rtw89_sar_sources src = rtwdev->sar.src;
+	/* its members are protected by rtw89_sar_set_src() */
+	const struct rtw89_sar_handler *sar_hdl = &rtw89_sar_handlers[src];
+	int ret;
+	s32 cfg;
+	u8 fct;
+
+	lockdep_assert_held(&rtwdev->mutex);
+
+	if (src == RTW89_SAR_SOURCE_NONE)
+		return RTW89_SAR_TXPWR_MAC_MAX;
+
+	ret = sar_hdl->query_sar_config(rtwdev, &cfg);
+	if (ret)
+		return RTW89_SAR_TXPWR_MAC_MAX;
+
+	fct = sar_hdl->txpwr_factor_sar;
+
+	return rtw89_txpwr_sar_to_mac(rtwdev, fct, cfg);
+}
+
+void rtw89_print_sar(struct seq_file *m, struct rtw89_dev *rtwdev)
+{
+	const enum rtw89_sar_sources src = rtwdev->sar.src;
+	/* its members are protected by rtw89_sar_set_src() */
+	const struct rtw89_sar_handler *sar_hdl = &rtw89_sar_handlers[src];
+	const u8 fct_mac = rtwdev->chip->txpwr_factor_mac;
+	int ret;
+	s32 cfg;
+	u8 fct;
+
+	lockdep_assert_held(&rtwdev->mutex);
+
+	if (src == RTW89_SAR_SOURCE_NONE) {
+		seq_puts(m, "no SAR is applied\n");
+		return;
+	}
+
+	seq_printf(m, "source: %d (%s)\n", src, sar_hdl->descr_sar_source);
+
+	ret = sar_hdl->query_sar_config(rtwdev, &cfg);
+	if (ret) {
+		seq_printf(m, "config: return code: %d\n", ret);
+		seq_printf(m, "assign: max setting: %d (unit: 1/%lu dBm)\n",
+			   RTW89_SAR_TXPWR_MAC_MAX, BIT(fct_mac));
+		return;
+	}
+
+	fct = sar_hdl->txpwr_factor_sar;
+
+	seq_printf(m, "config: %d (unit: 1/%lu dBm)\n", cfg, BIT(fct));
+}
+
+static int rtw89_apply_sar_common(struct rtw89_dev *rtwdev,
+				  const struct rtw89_sar_cfg_common *sar)
+{
+	enum rtw89_sar_sources src;
+	int ret = 0;
+
+	mutex_lock(&rtwdev->mutex);
+
+	src = rtwdev->sar.src;
+	if (src != RTW89_SAR_SOURCE_NONE && src != RTW89_SAR_SOURCE_COMMON) {
+		rtw89_warn(rtwdev, "SAR source: %d is in use", src);
+		ret = -EBUSY;
+		goto exit;
+	}
+
+	rtw89_sar_set_src(rtwdev, RTW89_SAR_SOURCE_COMMON, cfg_common, sar);
+	rtw89_chip_set_txpwr(rtwdev);
+
+exit:
+	mutex_unlock(&rtwdev->mutex);
+	return ret;
+}
+
+static const u8 rtw89_common_sar_subband_map[] = {
+	RTW89_CH_2G,
+	RTW89_CH_5G_BAND_1,
+	RTW89_CH_5G_BAND_3,
+	RTW89_CH_5G_BAND_4,
+};
+
+static const struct cfg80211_sar_freq_ranges rtw89_common_sar_freq_ranges[] = {
+	{ .start_freq = 2412, .end_freq = 2484, },
+	{ .start_freq = 5180, .end_freq = 5320, },
+	{ .start_freq = 5500, .end_freq = 5720, },
+	{ .start_freq = 5745, .end_freq = 5825, },
+};
+
+static_assert(ARRAY_SIZE(rtw89_common_sar_subband_map) ==
+	      ARRAY_SIZE(rtw89_common_sar_freq_ranges));
+
+const struct cfg80211_sar_capa rtw89_sar_capa = {
+	.type = NL80211_SAR_TYPE_POWER,
+	.num_freq_ranges = ARRAY_SIZE(rtw89_common_sar_freq_ranges),
+	.freq_ranges = rtw89_common_sar_freq_ranges,
+};
+
+int rtw89_ops_set_sar_specs(struct ieee80211_hw *hw,
+			    const struct cfg80211_sar_specs *sar)
+{
+	struct rtw89_dev *rtwdev = hw->priv;
+	struct rtw89_sar_cfg_common sar_common = {0};
+	u8 fct;
+	u32 freq_start;
+	u32 freq_end;
+	u32 band;
+	s32 power;
+	u32 i, idx;
+
+	if (sar->type != NL80211_SAR_TYPE_POWER)
+		return -EINVAL;
+
+	fct = rtw89_sar_handlers[RTW89_SAR_SOURCE_COMMON].txpwr_factor_sar;
+
+	for (i = 0; i < sar->num_sub_specs; i++) {
+		idx = sar->sub_specs[i].freq_range_index;
+		if (idx >= ARRAY_SIZE(rtw89_common_sar_freq_ranges))
+			return -EINVAL;
+
+		freq_start = rtw89_common_sar_freq_ranges[idx].start_freq;
+		freq_end = rtw89_common_sar_freq_ranges[idx].end_freq;
+		band = rtw89_common_sar_subband_map[idx];
+		power = sar->sub_specs[i].power;
+
+		rtw89_info(rtwdev, "On freq %u to %u, ", freq_start, freq_end);
+		rtw89_info(rtwdev, "set SAR power limit %d (unit: 1/%lu dBm)\n",
+			   power, BIT(fct));
+
+		sar_common.set[band] = true;
+		sar_common.cfg[band] = power;
+	}
+
+	return rtw89_apply_sar_common(rtwdev, &sar_common);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/sar.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/sar.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_SAR_H__
+#define __RTW89_SAR_H__
+
+#include "core.h"
+
+#define RTW89_SAR_TXPWR_MAC_MAX S8_MAX
+#define RTW89_SAR_TXPWR_MAC_MIN S8_MIN
+
+struct rtw89_sar_handler {
+	const char *descr_sar_source;
+	u8 txpwr_factor_sar;
+	int (*query_sar_config)(struct rtw89_dev *rtwdev, s32 *cfg);
+};
+
+extern const struct cfg80211_sar_capa rtw89_sar_capa;
+
+s8 rtw89_query_sar(struct rtw89_dev *rtwdev);
+void rtw89_print_sar(struct seq_file *m, struct rtw89_dev *rtwdev);
+int rtw89_ops_set_sar_specs(struct ieee80211_hw *hw,
+			    const struct cfg80211_sar_specs *sar);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/ser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/ser.c
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2019-2020  Realtek Corporation
+ */
+
+#include "cam.h"
+#include "debug.h"
+#include "mac.h"
+#include "ps.h"
+#include "ser.h"
+#include "util.h"
+
+#define SER_RECFG_TIMEOUT 1000
+
+enum ser_evt {
+	SER_EV_NONE,
+	SER_EV_STATE_IN,
+	SER_EV_STATE_OUT,
+	SER_EV_L1_RESET, /* M1 */
+	SER_EV_DO_RECOVERY, /* M3 */
+	SER_EV_MAC_RESET_DONE, /* M5 */
+	SER_EV_L2_RESET,
+	SER_EV_L2_RECFG_DONE,
+	SER_EV_L2_RECFG_TIMEOUT,
+	SER_EV_M3_TIMEOUT,
+	SER_EV_FW_M5_TIMEOUT,
+	SER_EV_L0_RESET,
+	SER_EV_MAXX
+};
+
+enum ser_state {
+	SER_IDLE_ST,
+	SER_RESET_TRX_ST,
+	SER_DO_HCI_ST,
+	SER_L2_RESET_ST,
+	SER_ST_MAX_ST
+};
+
+struct ser_msg {
+	struct list_head list;
+	u8 event;
+};
+
+struct state_ent {
+	u8 state;
+	char *name;
+	void (*st_func)(struct rtw89_ser *ser, u8 event);
+};
+
+struct event_ent {
+	u8 event;
+	char *name;
+};
+
+static char *ser_ev_name(struct rtw89_ser *ser, u8 event)
+{
+	if (event < SER_EV_MAXX)
+		return ser->ev_tbl[event].name;
+
+	return "err_ev_name";
+}
+
+static char *ser_st_name(struct rtw89_ser *ser)
+{
+	if (ser->state < SER_ST_MAX_ST)
+		return ser->st_tbl[ser->state].name;
+
+	return "err_st_name";
+}
+
+static void ser_state_run(struct rtw89_ser *ser, u8 evt)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	rtw89_debug(rtwdev, RTW89_DBG_SER, "ser: %s receive %s\n",
+		    ser_st_name(ser), ser_ev_name(ser, evt));
+
+	rtw89_leave_lps(rtwdev);
+	ser->st_tbl[ser->state].st_func(ser, evt);
+}
+
+static void ser_state_goto(struct rtw89_ser *ser, u8 new_state)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	if (ser->state == new_state || new_state >= SER_ST_MAX_ST)
+		return;
+	ser_state_run(ser, SER_EV_STATE_OUT);
+
+	rtw89_debug(rtwdev, RTW89_DBG_SER, "ser: %s goto -> %s\n",
+		    ser_st_name(ser), ser->st_tbl[new_state].name);
+
+	ser->state = new_state;
+	ser_state_run(ser, SER_EV_STATE_IN);
+}
+
+static struct ser_msg *__rtw89_ser_dequeue_msg(struct rtw89_ser *ser)
+{
+	struct ser_msg *msg;
+
+	spin_lock_irq(&ser->msg_q_lock);
+	msg = list_first_entry_or_null(&ser->msg_q, struct ser_msg, list);
+	if (msg)
+		list_del(&msg->list);
+	spin_unlock_irq(&ser->msg_q_lock);
+
+	return msg;
+}
+
+static void rtw89_ser_hdl_work(struct work_struct *work)
+{
+	struct ser_msg *msg;
+	struct rtw89_ser *ser = container_of(work, struct rtw89_ser,
+					     ser_hdl_work);
+
+	while ((msg = __rtw89_ser_dequeue_msg(ser))) {
+		ser_state_run(ser, msg->event);
+		kfree(msg);
+	}
+}
+
+static int ser_send_msg(struct rtw89_ser *ser, u8 event)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+	struct ser_msg *msg = NULL;
+
+	if (test_bit(RTW89_SER_DRV_STOP_RUN, ser->flags))
+		return -EIO;
+
+	msg = kmalloc(sizeof(*msg), GFP_ATOMIC);
+	if (!msg)
+		return -ENOMEM;
+
+	msg->event = event;
+
+	spin_lock_irq(&ser->msg_q_lock);
+	list_add(&msg->list, &ser->msg_q);
+	spin_unlock_irq(&ser->msg_q_lock);
+
+	ieee80211_queue_work(rtwdev->hw, &ser->ser_hdl_work);
+	return 0;
+}
+
+static void rtw89_ser_alarm_work(struct work_struct *work)
+{
+	struct rtw89_ser *ser = container_of(work, struct rtw89_ser,
+					     ser_alarm_work.work);
+
+	ser_send_msg(ser, ser->alarm_event);
+	ser->alarm_event = SER_EV_NONE;
+}
+
+static void ser_set_alarm(struct rtw89_ser *ser, u32 ms, u8 event)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	if (test_bit(RTW89_SER_DRV_STOP_RUN, ser->flags))
+		return;
+
+	ser->alarm_event = event;
+	ieee80211_queue_delayed_work(rtwdev->hw, &ser->ser_alarm_work,
+				     msecs_to_jiffies(ms));
+}
+
+static void ser_del_alarm(struct rtw89_ser *ser)
+{
+	cancel_delayed_work(&ser->ser_alarm_work);
+	ser->alarm_event = SER_EV_NONE;
+}
+
+/* driver function */
+static void drv_stop_tx(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	ieee80211_stop_queues(rtwdev->hw);
+	set_bit(RTW89_SER_DRV_STOP_TX, ser->flags);
+}
+
+static void drv_stop_rx(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	clear_bit(RTW89_FLAG_RUNNING, rtwdev->flags);
+	set_bit(RTW89_SER_DRV_STOP_RX, ser->flags);
+}
+
+static void drv_trx_reset(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	rtw89_hci_reset(rtwdev);
+}
+
+static void drv_resume_tx(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	if (!test_bit(RTW89_SER_DRV_STOP_TX, ser->flags))
+		return;
+
+	ieee80211_wake_queues(rtwdev->hw);
+	clear_bit(RTW89_SER_DRV_STOP_TX, ser->flags);
+}
+
+static void drv_resume_rx(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	if (!test_bit(RTW89_SER_DRV_STOP_RX, ser->flags))
+		return;
+
+	set_bit(RTW89_FLAG_RUNNING, rtwdev->flags);
+	clear_bit(RTW89_SER_DRV_STOP_RX, ser->flags);
+}
+
+static void ser_reset_vif(struct rtw89_dev *rtwdev, struct rtw89_vif *rtwvif)
+{
+	rtw89_core_release_bit_map(rtwdev->hw_port, rtwvif->port);
+	rtwvif->net_type = RTW89_NET_TYPE_NO_LINK;
+	rtwvif->trigger = false;
+}
+
+static void ser_reset_mac_binding(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_vif *rtwvif;
+
+	rtw89_cam_reset_keys(rtwdev);
+	rtw89_core_release_all_bits_map(rtwdev->mac_id_map, RTW89_MAX_MAC_ID_NUM);
+	rtw89_for_each_rtwvif(rtwdev, rtwvif)
+		ser_reset_vif(rtwdev, rtwvif);
+}
+
+/* hal function */
+static int hal_enable_dma(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+	int ret;
+
+	if (!test_bit(RTW89_SER_HAL_STOP_DMA, ser->flags))
+		return 0;
+
+	if (!rtwdev->hci.ops->mac_lv1_rcvy)
+		return -EIO;
+
+	ret = rtwdev->hci.ops->mac_lv1_rcvy(rtwdev, RTW89_LV1_RCVY_STEP_2);
+	if (!ret)
+		clear_bit(RTW89_SER_HAL_STOP_DMA, ser->flags);
+
+	return ret;
+}
+
+static int hal_stop_dma(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+	int ret;
+
+	if (!rtwdev->hci.ops->mac_lv1_rcvy)
+		return -EIO;
+
+	ret = rtwdev->hci.ops->mac_lv1_rcvy(rtwdev, RTW89_LV1_RCVY_STEP_1);
+	if (!ret)
+		set_bit(RTW89_SER_HAL_STOP_DMA, ser->flags);
+
+	return ret;
+}
+
+static void hal_send_m2_event(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	rtw89_mac_set_err_status(rtwdev, MAC_AX_ERR_L1_DISABLE_EN);
+}
+
+static void hal_send_m4_event(struct rtw89_ser *ser)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	rtw89_mac_set_err_status(rtwdev, MAC_AX_ERR_L1_RCVY_EN);
+}
+
+/* state handler */
+static void ser_idle_st_hdl(struct rtw89_ser *ser, u8 evt)
+{
+	switch (evt) {
+	case SER_EV_STATE_IN:
+		break;
+	case SER_EV_L1_RESET:
+		ser_state_goto(ser, SER_RESET_TRX_ST);
+		break;
+	case SER_EV_L2_RESET:
+		ser_state_goto(ser, SER_L2_RESET_ST);
+		break;
+	case SER_EV_STATE_OUT:
+	default:
+		break;
+	}
+}
+
+static void ser_reset_trx_st_hdl(struct rtw89_ser *ser, u8 evt)
+{
+	switch (evt) {
+	case SER_EV_STATE_IN:
+		drv_stop_tx(ser);
+
+		if (hal_stop_dma(ser)) {
+			ser_state_goto(ser, SER_L2_RESET_ST);
+			break;
+		}
+
+		drv_stop_rx(ser);
+		drv_trx_reset(ser);
+
+		/* wait m3 */
+		hal_send_m2_event(ser);
+
+		/* set alarm to prevent FW response timeout */
+		ser_set_alarm(ser, 1000, SER_EV_M3_TIMEOUT);
+		break;
+
+	case SER_EV_DO_RECOVERY:
+		ser_state_goto(ser, SER_DO_HCI_ST);
+		break;
+
+	case SER_EV_M3_TIMEOUT:
+		ser_state_goto(ser, SER_L2_RESET_ST);
+		break;
+
+	case SER_EV_STATE_OUT:
+		ser_del_alarm(ser);
+		hal_enable_dma(ser);
+		drv_resume_rx(ser);
+		drv_resume_tx(ser);
+		break;
+
+	default:
+		break;
+	}
+}
+
+static void ser_do_hci_st_hdl(struct rtw89_ser *ser, u8 evt)
+{
+	switch (evt) {
+	case SER_EV_STATE_IN:
+		/* wait m5 */
+		hal_send_m4_event(ser);
+
+		/* prevent FW response timeout */
+		ser_set_alarm(ser, 1000, SER_EV_FW_M5_TIMEOUT);
+		break;
+
+	case SER_EV_FW_M5_TIMEOUT:
+		ser_state_goto(ser, SER_L2_RESET_ST);
+		break;
+
+	case SER_EV_MAC_RESET_DONE:
+		ser_state_goto(ser, SER_IDLE_ST);
+		break;
+
+	case SER_EV_STATE_OUT:
+		ser_del_alarm(ser);
+		break;
+
+	default:
+		break;
+	}
+}
+
+static void ser_l2_reset_st_hdl(struct rtw89_ser *ser, u8 evt)
+{
+	struct rtw89_dev *rtwdev = container_of(ser, struct rtw89_dev, ser);
+
+	switch (evt) {
+	case SER_EV_STATE_IN:
+		mutex_lock(&rtwdev->mutex);
+		ser_reset_mac_binding(rtwdev);
+		rtw89_core_stop(rtwdev);
+		mutex_unlock(&rtwdev->mutex);
+
+		ieee80211_restart_hw(rtwdev->hw);
+		ser_set_alarm(ser, SER_RECFG_TIMEOUT, SER_EV_L2_RECFG_TIMEOUT);
+		break;
+
+	case SER_EV_L2_RECFG_TIMEOUT:
+		rtw89_info(rtwdev, "Err: ser L2 re-config timeout\n");
+		fallthrough;
+	case SER_EV_L2_RECFG_DONE:
+		ser_state_goto(ser, SER_IDLE_ST);
+		break;
+
+	case SER_EV_STATE_OUT:
+		ser_del_alarm(ser);
+		break;
+
+	default:
+		break;
+	}
+}
+
+static struct event_ent ser_ev_tbl[] = {
+	{SER_EV_NONE, "SER_EV_NONE"},
+	{SER_EV_STATE_IN, "SER_EV_STATE_IN"},
+	{SER_EV_STATE_OUT, "SER_EV_STATE_OUT"},
+	{SER_EV_L1_RESET, "SER_EV_L1_RESET"},
+	{SER_EV_DO_RECOVERY, "SER_EV_DO_RECOVERY m3"},
+	{SER_EV_MAC_RESET_DONE, "SER_EV_MAC_RESET_DONE m5"},
+	{SER_EV_L2_RESET, "SER_EV_L2_RESET"},
+	{SER_EV_L2_RECFG_DONE, "SER_EV_L2_RECFG_DONE"},
+	{SER_EV_L2_RECFG_TIMEOUT, "SER_EV_L2_RECFG_TIMEOUT"},
+	{SER_EV_M3_TIMEOUT, "SER_EV_M3_TIMEOUT"},
+	{SER_EV_FW_M5_TIMEOUT, "SER_EV_FW_M5_TIMEOUT"},
+	{SER_EV_L0_RESET, "SER_EV_L0_RESET"},
+	{SER_EV_MAXX, "SER_EV_MAX"}
+};
+
+static struct state_ent ser_st_tbl[] = {
+	{SER_IDLE_ST, "SER_IDLE_ST", ser_idle_st_hdl},
+	{SER_RESET_TRX_ST, "SER_RESET_TRX_ST", ser_reset_trx_st_hdl},
+	{SER_DO_HCI_ST, "SER_DO_HCI_ST", ser_do_hci_st_hdl},
+	{SER_L2_RESET_ST, "SER_L2_RESET_ST", ser_l2_reset_st_hdl}
+};
+
+int rtw89_ser_init(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_ser *ser = &rtwdev->ser;
+
+	memset(ser, 0, sizeof(*ser));
+	INIT_LIST_HEAD(&ser->msg_q);
+	ser->state = SER_IDLE_ST;
+	ser->st_tbl = ser_st_tbl;
+	ser->ev_tbl = ser_ev_tbl;
+
+	bitmap_zero(ser->flags, RTW89_NUM_OF_SER_FLAGS);
+	spin_lock_init(&ser->msg_q_lock);
+	INIT_WORK(&ser->ser_hdl_work, rtw89_ser_hdl_work);
+	INIT_DELAYED_WORK(&ser->ser_alarm_work, rtw89_ser_alarm_work);
+	return 0;
+}
+
+int rtw89_ser_deinit(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_ser *ser = (struct rtw89_ser *)&rtwdev->ser;
+
+	set_bit(RTW89_SER_DRV_STOP_RUN, ser->flags);
+	cancel_delayed_work_sync(&ser->ser_alarm_work);
+	cancel_work_sync(&ser->ser_hdl_work);
+	clear_bit(RTW89_SER_DRV_STOP_RUN, ser->flags);
+	return 0;
+}
+
+void rtw89_ser_recfg_done(struct rtw89_dev *rtwdev)
+{
+	ser_send_msg(&rtwdev->ser, SER_EV_L2_RECFG_DONE);
+}
+
+int rtw89_ser_notify(struct rtw89_dev *rtwdev, u32 err)
+{
+	u8 event = SER_EV_NONE;
+
+	rtw89_info(rtwdev, "ser event = 0x%04x\n", err);
+
+	switch (err) {
+	case MAC_AX_ERR_L1_ERR_DMAC:
+	case MAC_AX_ERR_L0_PROMOTE_TO_L1:
+		event = SER_EV_L1_RESET; /* M1 */
+		break;
+	case MAC_AX_ERR_L1_RESET_DISABLE_DMAC_DONE:
+		event = SER_EV_DO_RECOVERY; /* M3 */
+		break;
+	case MAC_AX_ERR_L1_RESET_RECOVERY_DONE:
+		event = SER_EV_MAC_RESET_DONE; /* M5 */
+		break;
+	case MAC_AX_ERR_L0_ERR_CMAC0:
+	case MAC_AX_ERR_L0_ERR_CMAC1:
+	case MAC_AX_ERR_L0_RESET_DONE:
+		event = SER_EV_L0_RESET;
+		break;
+	default:
+		if (err == MAC_AX_ERR_L1_PROMOTE_TO_L2 ||
+		    (err >= MAC_AX_ERR_L2_ERR_AH_DMA &&
+		     err <= MAC_AX_GET_ERR_MAX))
+			event = SER_EV_L2_RESET;
+		break;
+	}
+
+	if (event == SER_EV_NONE)
+		return -EINVAL;
+
+	ser_send_msg(&rtwdev->ser, event);
+	return 0;
+}
+EXPORT_SYMBOL(rtw89_ser_notify);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/ser.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/ser.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+ * Copyright(c) 2019-2020  Realtek Corporation
+ */
+#ifndef __SER_H__
+#define __SER_H__
+
+#include "core.h"
+
+int rtw89_ser_init(struct rtw89_dev *rtwdev);
+int rtw89_ser_deinit(struct rtw89_dev *rtwdev);
+int rtw89_ser_notify(struct rtw89_dev *rtwdev, u32 err);
+void rtw89_ser_recfg_done(struct rtw89_dev *rtwdev);
+
+#endif /* __SER_H__*/
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/txrx.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/txrx.h
@@ -0,0 +1,358 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_TXRX_H__
+#define __RTW89_TXRX_H__
+
+#include "debug.h"
+
+#define DATA_RATE_MODE_CTRL_MASK	GENMASK(8, 7)
+#define DATA_RATE_NOT_HT_IDX_MASK	GENMASK(3, 0)
+#define DATA_RATE_MODE_NON_HT		0x0
+#define DATA_RATE_HT_IDX_MASK		GENMASK(4, 0)
+#define DATA_RATE_MODE_HT		0x1
+#define DATA_RATE_VHT_HE_NSS_MASK	GENMASK(6, 4)
+#define DATA_RATE_VHT_HE_IDX_MASK	GENMASK(3, 0)
+#define DATA_RATE_MODE_VHT		0x2
+#define DATA_RATE_MODE_HE		0x3
+#define GET_DATA_RATE_MODE(r)		FIELD_GET(DATA_RATE_MODE_CTRL_MASK, r)
+#define GET_DATA_RATE_NOT_HT_IDX(r)	FIELD_GET(DATA_RATE_NOT_HT_IDX_MASK, r)
+#define GET_DATA_RATE_HT_IDX(r)		FIELD_GET(DATA_RATE_HT_IDX_MASK, r)
+#define GET_DATA_RATE_VHT_HE_IDX(r)	FIELD_GET(DATA_RATE_VHT_HE_IDX_MASK, r)
+#define GET_DATA_RATE_NSS(r)		FIELD_GET(DATA_RATE_VHT_HE_NSS_MASK, r)
+
+/* TX WD BODY DWORD 0 */
+#define RTW89_TXWD_BODY0_WP_OFFSET GENMASK(31, 24)
+#define RTW89_TXWD_BODY0_MORE_DATA BIT(23)
+#define RTW89_TXWD_BODY0_WD_INFO_EN BIT(22)
+#define RTW89_TXWD_BODY0_FW_DL BIT(20)
+#define RTW89_TXWD_BODY0_CHANNEL_DMA GENMASK(19, 16)
+#define RTW89_TXWD_BODY0_HDR_LLC_LEN GENMASK(15, 11)
+#define RTW89_TXWD_BODY0_WD_PAGE BIT(7)
+#define RTW89_TXWD_BODY0_HW_AMSDU BIT(5)
+
+/* TX WD BODY DWORD 1 */
+#define RTW89_TXWD_BODY1_PAYLOAD_ID GENMASK(31, 16)
+
+/* TX WD BODY DWORD 2 */
+#define RTW89_TXWD_BODY2_MACID GENMASK(30, 24)
+#define RTW89_TXWD_BODY2_TID_INDICATE BIT(23)
+#define RTW89_TXWD_BODY2_QSEL GENMASK(22, 17)
+#define RTW89_TXWD_BODY2_TXPKT_SIZE GENMASK(13, 0)
+
+/* TX WD BODY DWORD 3 */
+#define RTW89_TXWD_BODY3_BK BIT(13)
+#define RTW89_TXWD_BODY3_AGG_EN BIT(12)
+#define RTW89_TXWD_BODY3_SW_SEQ GENMASK(11, 0)
+
+/* TX WD BODY DWORD 4 */
+
+/* TX WD BODY DWORD 5 */
+
+/* TX WD INFO DWORD 0 */
+#define RTW89_TXWD_INFO0_USE_RATE BIT(30)
+#define RTW89_TXWD_INFO0_DATA_BW GENMASK(29, 28)
+#define RTW89_TXWD_INFO0_GI_LTF GENMASK(27, 25)
+#define RTW89_TXWD_INFO0_DATA_RATE GENMASK(24, 16)
+#define RTW89_TXWD_INFO0_DISDATAFB BIT(10)
+
+/* TX WD INFO DWORD 1 */
+#define RTW89_TXWD_INFO1_DATA_RTY_LOWEST_RATE GENMASK(24, 16)
+#define RTW89_TXWD_INFO1_A_CTRL_BSR BIT(14)
+#define RTW89_TXWD_INFO1_MAX_AGGNUM GENMASK(7, 0)
+
+/* TX WD INFO DWORD 2 */
+#define RTW89_TXWD_INFO2_AMPDU_DENSITY GENMASK(20, 18)
+#define RTW89_TXWD_INFO2_SEC_TYPE GENMASK(12, 9)
+#define RTW89_TXWD_INFO2_SEC_HW_ENC BIT(8)
+#define RTW89_TXWD_INFO2_SEC_CAM_IDX GENMASK(7, 0)
+
+/* TX WD INFO DWORD 3 */
+
+/* TX WD INFO DWORD 4 */
+#define RTW89_TXWD_INFO4_RTS_EN BIT(27)
+#define RTW89_TXWD_INFO4_HW_RTS_EN BIT(31)
+
+/* TX WD INFO DWORD 5 */
+
+/* RX DESC helpers */
+/* Short Descriptor */
+#define RTW89_GET_RXWD_LONG_RXD(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, BIT(31))
+#define RTW89_GET_RXWD_DRV_INFO_SIZE(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, GENMASK(30, 28))
+#define RTW89_GET_RXWD_RPKT_TYPE(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, GENMASK(27, 24))
+#define RTW89_GET_RXWD_MAC_INFO_VALID(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, BIT(23))
+#define RTW89_GET_RXWD_BB_SEL(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, BIT(22))
+#define RTW89_GET_RXWD_HD_IV_LEN(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, GENMASK(21, 16))
+#define RTW89_GET_RXWD_SHIFT(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, GENMASK(15, 14))
+#define RTW89_GET_RXWD_PKT_SIZE(rxdesc) \
+	le32_get_bits((rxdesc)->dword0, GENMASK(13, 0))
+#define RTW89_GET_RXWD_BW(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, GENMASK(31, 30))
+#define RTW89_GET_RXWD_GI_LTF(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, GENMASK(27, 25))
+#define RTW89_GET_RXWD_DATA_RATE(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, GENMASK(24, 16))
+#define RTW89_GET_RXWD_USER_ID(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, GENMASK(15, 8))
+#define RTW89_GET_RXWD_SR_EN(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, BIT(7))
+#define RTW89_GET_RXWD_PPDU_CNT(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, GENMASK(6, 4))
+#define RTW89_GET_RXWD_PPDU_TYPE(rxdesc) \
+	le32_get_bits((rxdesc)->dword1, GENMASK(3, 0))
+#define RTW89_GET_RXWD_FREE_RUN_CNT(rxdesc) \
+	le32_get_bits((rxdesc)->dword2, GENMASK(31, 0))
+#define RTW89_GET_RXWD_ICV_ERR(rxdesc) \
+	le32_get_bits((rxdesc)->dword3, BIT(10))
+#define RTW89_GET_RXWD_CRC32_ERR(rxdesc) \
+	le32_get_bits((rxdesc)->dword3, BIT(9))
+#define RTW89_GET_RXWD_HW_DEC(rxdesc) \
+	le32_get_bits((rxdesc)->dword3, BIT(2))
+#define RTW89_GET_RXWD_SW_DEC(rxdesc) \
+	le32_get_bits((rxdesc)->dword3, BIT(1))
+#define RTW89_GET_RXWD_A1_MATCH(rxdesc) \
+	le32_get_bits((rxdesc)->dword3, BIT(0))
+
+/* Long Descriptor */
+#define RTW89_GET_RXWD_FRAG(rxdesc) \
+	le32_get_bits((rxdesc)->dword4, GENMASK(31, 28))
+#define RTW89_GET_RXWD_SEQ(rxdesc) \
+	le32_get_bits((rxdesc)->dword4, GENMASK(27, 16))
+#define RTW89_GET_RXWD_TYPE(rxdesc) \
+	le32_get_bits((rxdesc)->dword4, GENMASK(1, 0))
+#define RTW89_GET_RXWD_ADDR_CAM_VLD(rxdesc) \
+	le32_get_bits((rxdesc)->dword5, BIT(28))
+#define RTW89_GET_RXWD_RX_PL_ID(rxdesc) \
+	le32_get_bits((rxdesc)->dword5, GENMASK(27, 24))
+#define RTW89_GET_RXWD_MAC_ID(rxdesc) \
+	le32_get_bits((rxdesc)->dword5, GENMASK(23, 16))
+#define RTW89_GET_RXWD_ADDR_CAM_ID(rxdesc) \
+	le32_get_bits((rxdesc)->dword5, GENMASK(15, 8))
+#define RTW89_GET_RXWD_SEC_CAM_ID(rxdesc) \
+	le32_get_bits((rxdesc)->dword5, GENMASK(7, 0))
+
+#define RTW89_GET_RXINFO_USR_NUM(rpt) \
+	le32_get_bits(*((__le32 *)rpt), GENMASK(3, 0))
+#define RTW89_GET_RXINFO_FW_DEFINE(rpt) \
+	le32_get_bits(*((__le32 *)rpt), GENMASK(15, 8))
+#define RTW89_GET_RXINFO_LSIG_LEN(rpt) \
+	le32_get_bits(*((__le32 *)rpt), GENMASK(27, 16))
+#define RTW89_GET_RXINFO_IS_TO_SELF(rpt) \
+	le32_get_bits(*((__le32 *)rpt), BIT(28))
+#define RTW89_GET_RXINFO_RX_CNT_VLD(rpt) \
+	le32_get_bits(*((__le32 *)rpt), BIT(29))
+#define RTW89_GET_RXINFO_LONG_RXD(rpt) \
+	le32_get_bits(*((__le32 *)rpt), GENMASK(31, 30))
+#define RTW89_GET_RXINFO_SERVICE(rpt) \
+	le32_get_bits(*((__le32 *)(rpt) + 1), GENMASK(15, 0))
+#define RTW89_GET_RXINFO_PLCP_LEN(rpt) \
+	le32_get_bits(*((__le32 *)(rpt) + 1), GENMASK(23, 16))
+#define RTW89_GET_RXINFO_MAC_ID_VALID(rpt, usr) \
+	le32_get_bits(*((__le32 *)(rpt) + (usr) + 2), BIT(0))
+#define RTW89_GET_RXINFO_DATA(rpt, usr) \
+	le32_get_bits(*((__le32 *)(rpt) + (usr) + 2), BIT(1))
+#define RTW89_GET_RXINFO_CTRL(rpt, usr) \
+	le32_get_bits(*((__le32 *)(rpt) + (usr) + 2), BIT(2))
+#define RTW89_GET_RXINFO_MGMT(rpt, usr) \
+	le32_get_bits(*((__le32 *)(rpt) + (usr) + 2), BIT(3))
+#define RTW89_GET_RXINFO_BCM(rpt, usr) \
+	le32_get_bits(*((__le32 *)(rpt) + (usr) + 2), BIT(4))
+#define RTW89_GET_RXINFO_MACID(rpt, usr) \
+	le32_get_bits(*((__le32 *)(rpt) + (usr) + 2), GENMASK(15, 8))
+
+#define RTW89_GET_PHY_STS_RSSI_A(sts) \
+	le32_get_bits(*((__le32 *)(sts) + 1), GENMASK(7, 0))
+#define RTW89_GET_PHY_STS_RSSI_B(sts) \
+	le32_get_bits(*((__le32 *)(sts) + 1), GENMASK(15, 8))
+#define RTW89_GET_PHY_STS_RSSI_C(sts) \
+	le32_get_bits(*((__le32 *)(sts) + 1), GENMASK(23, 16))
+#define RTW89_GET_PHY_STS_RSSI_D(sts) \
+	le32_get_bits(*((__le32 *)(sts) + 1), GENMASK(31, 24))
+#define RTW89_GET_PHY_STS_LEN(sts) \
+	le32_get_bits(*((__le32 *)sts), GENMASK(15, 8))
+#define RTW89_GET_PHY_STS_RSSI_AVG(sts) \
+	le32_get_bits(*((__le32 *)sts), GENMASK(31, 24))
+#define RTW89_GET_PHY_STS_IE_TYPE(ie) \
+	le32_get_bits(*((__le32 *)ie), GENMASK(4, 0))
+#define RTW89_GET_PHY_STS_IE_LEN(ie) \
+	le32_get_bits(*((__le32 *)ie), GENMASK(11, 5))
+#define RTW89_GET_PHY_STS_IE0_CFO(ie) \
+	le32_get_bits(*((__le32 *)(ie) + 1), GENMASK(31, 20))
+
+enum rtw89_tx_channel {
+	RTW89_TXCH_ACH0	= 0,
+	RTW89_TXCH_ACH1	= 1,
+	RTW89_TXCH_ACH2	= 2,
+	RTW89_TXCH_ACH3	= 3,
+	RTW89_TXCH_ACH4	= 4,
+	RTW89_TXCH_ACH5	= 5,
+	RTW89_TXCH_ACH6	= 6,
+	RTW89_TXCH_ACH7	= 7,
+	RTW89_TXCH_CH8	= 8,  /* MGMT Band 0 */
+	RTW89_TXCH_CH9	= 9,  /* HI Band 0 */
+	RTW89_TXCH_CH10	= 10, /* MGMT Band 1 */
+	RTW89_TXCH_CH11	= 11, /* HI Band 1 */
+	RTW89_TXCH_CH12	= 12, /* FW CMD */
+
+	/* keep last */
+	RTW89_TXCH_NUM,
+	RTW89_TXCH_MAX = RTW89_TXCH_NUM - 1
+};
+
+enum rtw89_rx_channel {
+	RTW89_RXCH_RXQ	= 0,
+	RTW89_RXCH_RPQ	= 1,
+
+	/* keep last */
+	RTW89_RXCH_NUM,
+	RTW89_RXCH_MAX = RTW89_RXCH_NUM - 1
+};
+
+enum rtw89_tx_qsel {
+	RTW89_TX_QSEL_BE_0		= 0x00,
+	RTW89_TX_QSEL_BK_0		= 0x01,
+	RTW89_TX_QSEL_VI_0		= 0x02,
+	RTW89_TX_QSEL_VO_0		= 0x03,
+	RTW89_TX_QSEL_BE_1		= 0x04,
+	RTW89_TX_QSEL_BK_1		= 0x05,
+	RTW89_TX_QSEL_VI_1		= 0x06,
+	RTW89_TX_QSEL_VO_1		= 0x07,
+	RTW89_TX_QSEL_BE_2		= 0x08,
+	RTW89_TX_QSEL_BK_2		= 0x09,
+	RTW89_TX_QSEL_VI_2		= 0x0a,
+	RTW89_TX_QSEL_VO_2		= 0x0b,
+	RTW89_TX_QSEL_BE_3		= 0x0c,
+	RTW89_TX_QSEL_BK_3		= 0x0d,
+	RTW89_TX_QSEL_VI_3		= 0x0e,
+	RTW89_TX_QSEL_VO_3		= 0x0f,
+	RTW89_TX_QSEL_B0_BCN		= 0x10,
+	RTW89_TX_QSEL_B0_HI		= 0x11,
+	RTW89_TX_QSEL_B0_MGMT		= 0x12,
+	RTW89_TX_QSEL_B0_NOPS		= 0x13,
+	RTW89_TX_QSEL_B0_MGMT_FAST	= 0x14,
+	/* reserved */
+	/* reserved */
+	/* reserved */
+	RTW89_TX_QSEL_B1_BCN		= 0x18,
+	RTW89_TX_QSEL_B1_HI		= 0x19,
+	RTW89_TX_QSEL_B1_MGMT		= 0x1a,
+	RTW89_TX_QSEL_B1_NOPS		= 0x1b,
+	RTW89_TX_QSEL_B1_MGMT_FAST	= 0x1c,
+	/* reserved */
+	/* reserved */
+	/* reserved */
+};
+
+enum rtw89_phy_status_ie_type {
+	RTW89_PHYSTS_IE00_CMN_CCK			= 0,
+	RTW89_PHYSTS_IE01_CMN_OFDM			= 1,
+	RTW89_PHYSTS_IE02_CMN_EXT_AX			= 2,
+	RTW89_PHYSTS_IE03_CMN_EXT_SEG_1			= 3,
+	RTW89_PHYSTS_IE04_CMN_EXT_PATH_A		= 4,
+	RTW89_PHYSTS_IE05_CMN_EXT_PATH_B		= 5,
+	RTW89_PHYSTS_IE06_CMN_EXT_PATH_C		= 6,
+	RTW89_PHYSTS_IE07_CMN_EXT_PATH_D		= 7,
+	RTW89_PHYSTS_IE08_FTR_CH			= 8,
+	RTW89_PHYSTS_IE09_FTR_PLCP_0			= 9,
+	RTW89_PHYSTS_IE10_FTR_PLCP_EXT			= 10,
+	RTW89_PHYSTS_IE11_FTR_PLCP_HISTOGRAM		= 11,
+	RTW89_PHYSTS_IE12_MU_EIGEN_INFO			= 12,
+	RTW89_PHYSTS_IE13_DL_MU_DEF			= 13,
+	RTW89_PHYSTS_IE14_TB_UL_CQI			= 14,
+	RTW89_PHYSTS_IE15_TB_UL_DEF			= 15,
+	RTW89_PHYSTS_IE16_RSVD16			= 16,
+	RTW89_PHYSTS_IE17_TB_UL_CTRL			= 17,
+	RTW89_PHYSTS_IE18_DBG_OFDM_FD_CMN		= 18,
+	RTW89_PHYSTS_IE19_DBG_OFDM_TD_CMN		= 19,
+	RTW89_PHYSTS_IE20_DBG_OFDM_FD_USER_SEG_0	= 20,
+	RTW89_PHYSTS_IE21_DBG_OFDM_FD_USER_SEG_1	= 21,
+	RTW89_PHYSTS_IE22_DBG_OFDM_FD_USER_AGC		= 22,
+	RTW89_PHYSTS_IE23_RSVD23			= 23,
+	RTW89_PHYSTS_IE24_DBG_OFDM_TD_PATH_A		= 24,
+	RTW89_PHYSTS_IE25_DBG_OFDM_TD_PATH_B		= 25,
+	RTW89_PHYSTS_IE26_DBG_OFDM_TD_PATH_C		= 26,
+	RTW89_PHYSTS_IE27_DBG_OFDM_TD_PATH_D		= 27,
+	RTW89_PHYSTS_IE28_DBG_CCK_PATH_A		= 28,
+	RTW89_PHYSTS_IE29_DBG_CCK_PATH_B		= 29,
+	RTW89_PHYSTS_IE30_DBG_CCK_PATH_C		= 30,
+	RTW89_PHYSTS_IE31_DBG_CCK_PATH_D		= 31,
+
+	/* keep last */
+	RTW89_PHYSTS_IE_NUM,
+	RTW89_PHYSTS_IE_MAX = RTW89_PHYSTS_IE_NUM - 1
+};
+
+static inline u8 rtw89_core_get_qsel(struct rtw89_dev *rtwdev, u8 tid)
+{
+	switch (tid) {
+	default:
+		rtw89_warn(rtwdev, "Should use tag 1d: %d\n", tid);
+		fallthrough;
+	case 0:
+	case 3:
+		return RTW89_TX_QSEL_BE_0;
+	case 1:
+	case 2:
+		return RTW89_TX_QSEL_BK_0;
+	case 4:
+	case 5:
+		return RTW89_TX_QSEL_VI_0;
+	case 6:
+	case 7:
+		return RTW89_TX_QSEL_VO_0;
+	}
+}
+
+static inline u8 rtw89_core_get_ch_dma(struct rtw89_dev *rtwdev, u8 qsel)
+{
+	switch (qsel) {
+	default:
+		rtw89_warn(rtwdev, "Cannot map qsel to dma: %d\n", qsel);
+		fallthrough;
+	case RTW89_TX_QSEL_BE_0:
+		return RTW89_TXCH_ACH0;
+	case RTW89_TX_QSEL_BK_0:
+		return RTW89_TXCH_ACH1;
+	case RTW89_TX_QSEL_VI_0:
+		return RTW89_TXCH_ACH2;
+	case RTW89_TX_QSEL_VO_0:
+		return RTW89_TXCH_ACH3;
+	case RTW89_TX_QSEL_B0_MGMT:
+		return RTW89_TXCH_CH8;
+	case RTW89_TX_QSEL_B0_HI:
+		return RTW89_TXCH_CH9;
+	case RTW89_TX_QSEL_B1_MGMT:
+		return RTW89_TXCH_CH10;
+	case RTW89_TX_QSEL_B1_HI:
+		return RTW89_TXCH_CH11;
+	}
+}
+
+static inline u8 rtw89_core_get_tid_indicate(struct rtw89_dev *rtwdev, u8 tid)
+{
+	switch (tid) {
+	case 3:
+	case 2:
+	case 5:
+	case 7:
+		return 1;
+	default:
+		rtw89_warn(rtwdev, "Should use tag 1d: %d\n", tid);
+		fallthrough;
+	case 0:
+	case 1:
+	case 4:
+	case 6:
+		return 0;
+	}
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/realtek/rtw89/util.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/realtek/rtw89/util.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+ * Copyright(c) 2019-2020  Realtek Corporation
+ */
+#ifndef __RTW89_UTIL_H__
+#define __RTW89_UTIL_H__
+
+#include "core.h"
+
+#define rtw89_iterate_vifs_bh(rtwdev, iterator, data)                          \
+	ieee80211_iterate_active_interfaces_atomic((rtwdev)->hw,               \
+			IEEE80211_IFACE_ITER_NORMAL, iterator, data)
+
+/* call this function with rtwdev->mutex is held */
+#define rtw89_for_each_rtwvif(rtwdev, rtwvif)				       \
+	list_for_each_entry(rtwvif, &(rtwdev)->rtwvifs_list, list)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rndis_wlan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rndis_wlan.c
@@ -694,8 +694,8 @@
 		struct rndis_query	*get;
 		struct rndis_query_c	*get_c;
 	} u;
-	int ret, buflen;
-	int resplen, respoffs, copylen;
+	int ret;
+	size_t buflen, resplen, respoffs, copylen;
 
 	buflen = *len + sizeof(*u.get);
 	if (buflen < CONTROL_BUFFER_SIZE)
@@ -730,22 +730,15 @@
 
 		if (respoffs > buflen) {
 			/* Device returned data offset outside buffer, error. */
-			netdev_dbg(dev->net, "%s(%s): received invalid "
-				"data offset: %d > %d\n", __func__,
-				oid_to_string(oid), respoffs, buflen);
+			netdev_dbg(dev->net,
+				   "%s(%s): received invalid data offset: %zu > %zu\n",
+				   __func__, oid_to_string(oid), respoffs, buflen);
 
 			ret = -EINVAL;
 			goto exit_unlock;
 		}
 
-		if ((resplen + respoffs) > buflen) {
-			/* Device would have returned more data if buffer would
-			 * have been big enough. Copy just the bits that we got.
-			 */
-			copylen = buflen - respoffs;
-		} else {
-			copylen = resplen;
-		}
+		copylen = min(resplen, buflen - respoffs);
 
 		if (copylen > *len)
 			copylen = *len;
@@ -3501,7 +3494,6 @@
 	cancel_delayed_work_sync(&priv->dev_poller_work);
 	cancel_delayed_work_sync(&priv->scan_work);
 	cancel_work_sync(&priv->work);
-	flush_workqueue(priv->workqueue);
 	destroy_workqueue(priv->workqueue);
 
 	wiphy_free(wiphy);
@@ -3518,7 +3510,6 @@
 	cancel_delayed_work_sync(&priv->dev_poller_work);
 	cancel_delayed_work_sync(&priv->scan_work);
 	cancel_work_sync(&priv->work);
-	flush_workqueue(priv->workqueue);
 	destroy_workqueue(priv->workqueue);
 
 	rndis_unbind(usbdev, intf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_coex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_coex.c
@@ -160,6 +160,7 @@
 			       rsi_coex_scheduler_thread,
 			       "Coex-Tx-Thread")) {
 		rsi_dbg(ERR_ZONE, "%s: Unable to init tx thrd\n", __func__);
+		kfree(coex_cb);
 		return -EINVAL;
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_core.c
@@ -399,6 +399,8 @@
 
 	info = IEEE80211_SKB_CB(skb);
 	tx_params = (struct skb_info *)info->driver_data;
+	/* info->driver_data and info->control part of union so make copy */
+	tx_params->have_key = !!info->control.hw_key;
 	wh = (struct ieee80211_hdr *)&skb->data[0];
 	tx_params->sta_id = 0;
 
@@ -463,7 +465,9 @@
 							      tid, 0);
 			}
 		}
-		if (skb->protocol == cpu_to_be16(ETH_P_PAE)) {
+
+		if (IEEE80211_SKB_CB(skb)->control.flags &
+		    IEEE80211_TX_CTRL_PORT_CTRL_PROTO) {
 			q_num = MGMT_SOFT_Q;
 			skb->priority = q_num;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_hal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_hal.c
@@ -162,12 +162,16 @@
 	u8 header_size;
 	u8 vap_id = 0;
 	u8 dword_align_bytes;
+	bool tx_eapol;
 	u16 seq_num;
 
 	info = IEEE80211_SKB_CB(skb);
 	vif = info->control.vif;
 	tx_params = (struct skb_info *)info->driver_data;
 
+	tx_eapol = IEEE80211_SKB_CB(skb)->control.flags &
+		   IEEE80211_TX_CTRL_PORT_CTRL_PROTO;
+
 	header_size = FRAME_DESC_SZ + sizeof(struct rsi_xtended_desc);
 	if (header_size > skb_headroom(skb)) {
 		rsi_dbg(ERR_ZONE, "%s: Unable to send pkt\n", __func__);
@@ -203,7 +207,7 @@
 		wh->frame_control |= cpu_to_le16(RSI_SET_PS_ENABLE);
 
 	if ((!(info->flags & IEEE80211_TX_INTFL_DONT_ENCRYPT)) &&
-	    info->control.hw_key) {
+	    tx_params->have_key) {
 		if (rsi_is_cipher_wep(common))
 			ieee80211_size += 4;
 		else
@@ -214,22 +218,24 @@
 			RSI_WIFI_DATA_Q);
 	data_desc->header_len = ieee80211_size;
 
-	if (common->min_rate != RSI_RATE_AUTO) {
+	if (common->rate_config[common->band].fixed_enabled) {
 		/* Send fixed rate */
+		u16 fixed_rate = common->rate_config[common->band].fixed_hw_rate;
+
 		data_desc->frame_info = cpu_to_le16(RATE_INFO_ENABLE);
-		data_desc->rate_info = cpu_to_le16(common->min_rate);
+		data_desc->rate_info = cpu_to_le16(fixed_rate);
 
 		if (conf_is_ht40(&common->priv->hw->conf))
 			data_desc->bbp_info = cpu_to_le16(FULL40M_ENABLE);
 
-		if ((common->vif_info[0].sgi) && (common->min_rate & 0x100)) {
+		if (common->vif_info[0].sgi && (fixed_rate & 0x100)) {
 		       /* Only MCS rates */
 			data_desc->rate_info |=
 				cpu_to_le16(ENABLE_SHORTGI_RATE);
 		}
 	}
 
-	if (skb->protocol == cpu_to_be16(ETH_P_PAE)) {
+	if (tx_eapol) {
 		rsi_dbg(INFO_ZONE, "*** Tx EAPOL ***\n");
 
 		data_desc->frame_info = cpu_to_le16(RATE_INFO_ENABLE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_mac80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_mac80211.c
@@ -510,7 +510,6 @@
 	if ((vif->type == NL80211_IFTYPE_AP) ||
 	    (vif->type == NL80211_IFTYPE_P2P_GO)) {
 		rsi_send_rx_filter_frame(common, DISALLOW_BEACONS);
-		common->min_rate = RSI_RATE_AUTO;
 		for (i = 0; i < common->max_stations; i++)
 			common->stations[i].sta = NULL;
 	}
@@ -1228,20 +1227,32 @@
 				      struct ieee80211_vif *vif,
 				      const struct cfg80211_bitrate_mask *mask)
 {
+	const unsigned int mcs_offset = ARRAY_SIZE(rsi_rates);
 	struct rsi_hw *adapter = hw->priv;
 	struct rsi_common *common = adapter->priv;
-	enum nl80211_band band = hw->conf.chandef.chan->band;
+	int i;
 
 	mutex_lock(&common->mutex);
-	common->fixedrate_mask[band] = 0;
 
-	if (mask->control[band].legacy == 0xfff) {
-		common->fixedrate_mask[band] =
-			(mask->control[band].ht_mcs[0] << 12);
-	} else {
-		common->fixedrate_mask[band] =
-			mask->control[band].legacy;
+	for (i = 0; i < ARRAY_SIZE(common->rate_config); i++) {
+		struct rsi_rate_config *cfg = &common->rate_config[i];
+		u32 bm;
+
+		bm = mask->control[i].legacy | (mask->control[i].ht_mcs[0] << mcs_offset);
+		if (hweight32(bm) == 1) { /* single rate */
+			int rate_index = ffs(bm) - 1;
+
+			if (rate_index < mcs_offset)
+				cfg->fixed_hw_rate = rsi_rates[rate_index].hw_value;
+			else
+				cfg->fixed_hw_rate = rsi_mcsrates[rate_index - mcs_offset];
+			cfg->fixed_enabled = true;
+		} else {
+			cfg->configured_mask = bm;
+			cfg->fixed_enabled = false;
+		}
 	}
+
 	mutex_unlock(&common->mutex);
 
 	return 0;
@@ -1378,46 +1389,6 @@
 	ieee80211_rx_irqsafe(hw, skb);
 }
 
-static void rsi_set_min_rate(struct ieee80211_hw *hw,
-			     struct ieee80211_sta *sta,
-			     struct rsi_common *common)
-{
-	u8 band = hw->conf.chandef.chan->band;
-	u8 ii;
-	u32 rate_bitmap;
-	bool matched = false;
-
-	common->bitrate_mask[band] = sta->supp_rates[band];
-
-	rate_bitmap = (common->fixedrate_mask[band] & sta->supp_rates[band]);
-
-	if (rate_bitmap & 0xfff) {
-		/* Find out the min rate */
-		for (ii = 0; ii < ARRAY_SIZE(rsi_rates); ii++) {
-			if (rate_bitmap & BIT(ii)) {
-				common->min_rate = rsi_rates[ii].hw_value;
-				matched = true;
-				break;
-			}
-		}
-	}
-
-	common->vif_info[0].is_ht = sta->ht_cap.ht_supported;
-
-	if ((common->vif_info[0].is_ht) && (rate_bitmap >> 12)) {
-		for (ii = 0; ii < ARRAY_SIZE(rsi_mcsrates); ii++) {
-			if ((rate_bitmap >> 12) & BIT(ii)) {
-				common->min_rate = rsi_mcsrates[ii];
-				matched = true;
-				break;
-			}
-		}
-	}
-
-	if (!matched)
-		common->min_rate = 0xffff;
-}
-
 /**
  * rsi_mac80211_sta_add() - This function notifies driver about a peer getting
  *			    connected.
@@ -1516,9 +1487,9 @@
 
 	if ((vif->type == NL80211_IFTYPE_STATION) ||
 	    (vif->type == NL80211_IFTYPE_P2P_CLIENT)) {
-		rsi_set_min_rate(hw, sta, common);
+		common->bitrate_mask[common->band] = sta->supp_rates[common->band];
+		common->vif_info[0].is_ht = sta->ht_cap.ht_supported;
 		if (sta->ht_cap.ht_supported) {
-			common->vif_info[0].is_ht = true;
 			common->bitrate_mask[NL80211_BAND_2GHZ] =
 					sta->supp_rates[NL80211_BAND_2GHZ];
 			if ((sta->ht_cap.cap & IEEE80211_HT_CAP_SGI_20) ||
@@ -1592,7 +1563,6 @@
 		bss->qos = sta->wme;
 		common->bitrate_mask[NL80211_BAND_2GHZ] = 0;
 		common->bitrate_mask[NL80211_BAND_5GHZ] = 0;
-		common->min_rate = 0xffff;
 		common->vif_info[0].is_ht = false;
 		common->vif_info[0].sgi = false;
 		common->vif_info[0].seq_start = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_main.c
@@ -23,6 +23,7 @@
 #include "rsi_common.h"
 #include "rsi_coex.h"
 #include "rsi_hal.h"
+#include "rsi_usb.h"
 
 u32 rsi_zone_enabled = /* INFO_ZONE |
 			INIT_ZONE |
@@ -168,6 +169,9 @@
 		frame_desc = &rx_pkt[index];
 		actual_length = *(u16 *)&frame_desc[0];
 		offset = *(u16 *)&frame_desc[2];
+		if (!rcv_pkt_len && offset >
+			RSI_MAX_RX_USB_PKT_SIZE - FRAME_DESC_SZ)
+			goto fail;
 
 		queueno = rsi_get_queueno(frame_desc, offset);
 		length = rsi_get_length(frame_desc, offset);
@@ -211,9 +215,10 @@
 			bt_pkt_type = frame_desc[offset + BT_RX_PKT_TYPE_OFST];
 			if (bt_pkt_type == BT_CARD_READY_IND) {
 				rsi_dbg(INFO_ZONE, "BT Card ready recvd\n");
-				if (rsi_bt_ops.attach(common, &g_proto_ops))
-					rsi_dbg(ERR_ZONE,
-						"Failed to attach BT module\n");
+				if (common->fsm_state == FSM_MAC_INIT_DONE)
+					rsi_attach_bt(common);
+				else
+					common->bt_defer_attach = true;
 			} else {
 				if (common->bt_adapter)
 					rsi_bt_ops.recv_pkt(common->bt_adapter,
@@ -278,6 +283,15 @@
 }
 #endif
 
+void rsi_attach_bt(struct rsi_common *common)
+{
+#ifdef CONFIG_RSI_COEX
+	if (rsi_bt_ops.attach(common, &g_proto_ops))
+		rsi_dbg(ERR_ZONE,
+			"Failed to attach BT module\n");
+#endif
+}
+
 /**
  * rsi_91x_init() - This function initializes os interface operations.
  * @oper_mode: One of DEV_OPMODE_*.
@@ -359,6 +373,7 @@
 	if (common->coex_mode > 1) {
 		if (rsi_coex_attach(common)) {
 			rsi_dbg(ERR_ZONE, "Failed to init coex module\n");
+			rsi_kill_thread(&common->tx_thread);
 			goto err;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_mgmt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_mgmt.c
@@ -276,7 +276,7 @@
 	common->channel_width = BW_20MHZ;
 	common->rts_threshold = IEEE80211_MAX_RTS_THRESHOLD;
 	common->channel = 1;
-	common->min_rate = 0xffff;
+	memset(&common->rate_config, 0, sizeof(common->rate_config));
 	common->fsm_state = FSM_CARD_NOT_READY;
 	common->iface_down = true;
 	common->endpoint = EP_2GHZ_20MHZ;
@@ -1314,7 +1314,7 @@
 	u8 band = hw->conf.chandef.chan->band;
 	u8 num_supported_rates = 0;
 	u8 rate_table_offset, rate_offset = 0;
-	u32 rate_bitmap;
+	u32 rate_bitmap, configured_rates;
 	u16 *selected_rates, min_rate;
 	bool is_ht = false, is_sgi = false;
 	u16 frame_len = sizeof(struct rsi_auto_rate);
@@ -1364,6 +1364,10 @@
 			is_sgi = true;
 	}
 
+	/* Limit to any rates administratively configured by cfg80211 */
+	configured_rates = common->rate_config[band].configured_mask ?: 0xffffffff;
+	rate_bitmap &= configured_rates;
+
 	if (band == NL80211_BAND_2GHZ) {
 		if ((rate_bitmap == 0) && (is_ht))
 			min_rate = RSI_RATE_MCS0;
@@ -1389,10 +1393,13 @@
 	num_supported_rates = jj;
 
 	if (is_ht) {
-		for (ii = 0; ii < ARRAY_SIZE(mcs); ii++)
-			selected_rates[jj++] = mcs[ii];
-		num_supported_rates += ARRAY_SIZE(mcs);
-		rate_offset += ARRAY_SIZE(mcs);
+		for (ii = 0; ii < ARRAY_SIZE(mcs); ii++) {
+			if (configured_rates & BIT(ii + ARRAY_SIZE(rsi_rates))) {
+				selected_rates[jj++] = mcs[ii];
+				num_supported_rates++;
+				rate_offset++;
+			}
+		}
 	}
 
 	sort(selected_rates, jj, sizeof(u16), &rsi_compare, NULL);
@@ -1482,7 +1489,7 @@
 					      qos_enable,
 					      aid, sta_id,
 					      vif);
-		if (common->min_rate == 0xffff)
+		if (!common->rate_config[common->band].fixed_enabled)
 			rsi_send_auto_rate_request(common, sta, sta_id, vif);
 		if (opmode == RSI_OPMODE_STA &&
 		    !(assoc_cap & WLAN_CAPABILITY_PRIVACY) &&
@@ -2071,6 +2078,9 @@
 				if (common->reinit_hw) {
 					complete(&common->wlan_init_completion);
 				} else {
+					if (common->bt_defer_attach)
+						rsi_attach_bt(common);
+
 					return rsi_mac80211_attach(common);
 				}
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_sdio.c
@@ -24,10 +24,7 @@
 /* Default operating mode is wlan STA + BT */
 static u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL;
 module_param(dev_oper_mode, ushort, 0444);
-MODULE_PARM_DESC(dev_oper_mode,
-		 "1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n"
-		 "9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n"
-		 "6[AP + BT classic], 14[AP + BT classic + BT LE]");
+MODULE_PARM_DESC(dev_oper_mode, DEV_OPMODE_PARAM_DESC);
 
 /**
  * rsi_sdio_set_cmd52_arg() - This function prepares cmd 52 read/write arg.
@@ -1466,10 +1463,8 @@
 
 	rsi_dbg(ERR_ZONE, "SDIO Bus shutdown =====>\n");
 
-	if (hw) {
-		struct cfg80211_wowlan *wowlan = hw->wiphy->wowlan_config;
-
-		if (rsi_config_wowlan(adapter, wowlan))
+	if (hw && hw->wiphy && hw->wiphy->wowlan_config) {
+		if (rsi_config_wowlan(adapter, hw->wiphy->wowlan_config))
 			rsi_dbg(ERR_ZONE, "Failed to configure WoWLAN\n");
 	}
 
@@ -1484,9 +1479,6 @@
 	if (sdev->write_fail)
 		rsi_dbg(INFO_ZONE, "###### Device is not ready #######\n");
 
-	if (rsi_set_sdio_pm_caps(adapter))
-		rsi_dbg(INFO_ZONE, "Setting power management caps failed\n");
-
 	rsi_dbg(INFO_ZONE, "***** RSI module shut down *****\n");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_91x_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_91x_usb.c
@@ -25,10 +25,7 @@
 /* Default operating mode is wlan STA + BT */
 static u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL;
 module_param(dev_oper_mode, ushort, 0444);
-MODULE_PARM_DESC(dev_oper_mode,
-		 "1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n"
-		 "9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n"
-		 "6[AP + BT classic], 14[AP + BT classic + BT LE]");
+MODULE_PARM_DESC(dev_oper_mode, DEV_OPMODE_PARAM_DESC);
 
 static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num, gfp_t flags);
 
@@ -61,7 +58,7 @@
 			      (void *)seg,
 			      (int)len,
 			      &transfer,
-			      HZ * 5);
+			      USB_CTRL_SET_TIMEOUT);
 
 	if (status < 0) {
 		rsi_dbg(ERR_ZONE,
@@ -272,8 +269,12 @@
 	struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)rx_cb->data;
 	int status = -EINVAL;
 
+	if (!rx_cb->rx_skb)
+		return;
+
 	if (urb->status) {
 		dev_kfree_skb(rx_cb->rx_skb);
+		rx_cb->rx_skb = NULL;
 		return;
 	}
 
@@ -297,8 +298,10 @@
 	if (rsi_rx_urb_submit(dev->priv, rx_cb->ep_num, GFP_ATOMIC))
 		rsi_dbg(ERR_ZONE, "%s: Failed in urb submission", __func__);
 
-	if (status)
+	if (status) {
 		dev_kfree_skb(rx_cb->rx_skb);
+		rx_cb->rx_skb = NULL;
+	}
 }
 
 static void rsi_rx_urb_kill(struct rsi_hw *adapter, u8 ep_num)
@@ -327,7 +330,6 @@
 	struct sk_buff *skb;
 	u8 dword_align_bytes = 0;
 
-#define RSI_MAX_RX_USB_PKT_SIZE	3000
 	skb = dev_alloc_skb(RSI_MAX_RX_USB_PKT_SIZE);
 	if (!skb)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_hal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_hal.h
@@ -28,6 +28,17 @@
 #define DEV_OPMODE_AP_BT		6
 #define DEV_OPMODE_AP_BT_DUAL		14
 
+#define DEV_OPMODE_PARAM_DESC		\
+	__stringify(DEV_OPMODE_WIFI_ALONE)	"[Wi-Fi alone], "	\
+	__stringify(DEV_OPMODE_BT_ALONE)	"[BT classic alone], "	\
+	__stringify(DEV_OPMODE_BT_LE_ALONE)	"[BT LE alone], "	\
+	__stringify(DEV_OPMODE_BT_DUAL)		"[BT classic + BT LE alone], " \
+	__stringify(DEV_OPMODE_STA_BT)		"[Wi-Fi STA + BT classic], " \
+	__stringify(DEV_OPMODE_STA_BT_LE)	"[Wi-Fi STA + BT LE], "	\
+	__stringify(DEV_OPMODE_STA_BT_DUAL)	"[Wi-Fi STA + BT classic + BT LE], " \
+	__stringify(DEV_OPMODE_AP_BT)		"[Wi-Fi AP + BT classic], "	\
+	__stringify(DEV_OPMODE_AP_BT_DUAL)	"[Wi-Fi AP + BT classic + BT LE]"
+
 #define FLASH_WRITE_CHUNK_SIZE		(4 * 1024)
 #define FLASH_SECTOR_SIZE		(4 * 1024)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_main.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_main.h
@@ -61,6 +61,7 @@
 extern u32 rsi_zone_enabled;
 extern __printf(2, 3) void rsi_dbg(u32 zone, const char *fmt, ...);
 
+#define RSI_MAX_BANDS			2
 #define RSI_MAX_VIFS                    3
 #define NUM_EDCA_QUEUES                 4
 #define IEEE80211_ADDR_LEN              6
@@ -139,6 +140,7 @@
 	u8 internal_hdr_size;
 	struct ieee80211_vif *vif;
 	u8 vap_id;
+	bool have_key;
 };
 
 enum edca_queue {
@@ -229,6 +231,12 @@
 	u32 ps_options;
 };
 
+struct rsi_rate_config {
+	u32 configured_mask;	/* configured by mac80211 bits 0-11=legacy 12+ mcs */
+	u16 fixed_hw_rate;
+	bool fixed_enabled;
+};
+
 struct rsi_common {
 	struct rsi_hw *priv;
 	struct vif_priv vif_info[RSI_MAX_VIFS];
@@ -254,8 +262,8 @@
 	u8 channel_width;
 
 	u16 rts_threshold;
-	u16 bitrate_mask[2];
-	u32 fixedrate_mask[2];
+	u32 bitrate_mask[RSI_MAX_BANDS];
+	struct rsi_rate_config rate_config[RSI_MAX_BANDS];
 
 	u8 rf_reset;
 	struct transmit_q_stats tx_stats;
@@ -276,7 +284,6 @@
 	u8 mac_id;
 	u8 radio_id;
 	u16 rate_pwr[20];
-	u16 min_rate;
 
 	/* WMM algo related */
 	u8 selected_qnum;
@@ -320,6 +327,7 @@
 	struct ieee80211_vif *roc_vif;
 
 	bool eapol4_confirm;
+	bool bt_defer_attach;
 	void *bt_adapter;
 
 	struct cfg80211_scan_request *hwscan;
@@ -401,5 +409,6 @@
 
 enum rsi_host_intf rsi_get_host_intf(void *priv);
 void rsi_set_bt_context(void *priv, void *bt_context);
+void rsi_attach_bt(struct rsi_common *common);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/rsi/rsi_usb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/rsi/rsi_usb.h
@@ -44,6 +44,8 @@
 #define RSI_USB_BUF_SIZE	     4096
 #define RSI_USB_CTRL_BUF_SIZE	     0x04
 
+#define RSI_MAX_RX_USB_PKT_SIZE	3000
+
 struct rx_usb_ctrl_block {
 	u8 *data;
 	struct urb *rx_urb;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/st/cw1200/bh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/st/cw1200/bh.c
@@ -85,8 +85,6 @@
 	atomic_inc(&priv->bh_term);
 	wake_up(&priv->bh_wq);
 
-	flush_workqueue(priv->bh_workqueue);
-
 	destroy_workqueue(priv->bh_workqueue);
 	priv->bh_workqueue = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/st/cw1200/txrx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/st/cw1200/txrx.c
@@ -1170,7 +1170,7 @@
 		size_t ies_len = skb->len - (ies - (u8 *)(skb->data));
 
 		tim_ie = cfg80211_find_ie(WLAN_EID_TIM, ies, ies_len);
-		if (tim_ie) {
+		if (tim_ie && tim_ie[1] >= sizeof(struct ieee80211_tim_ie)) {
 			struct ieee80211_tim_ie *tim =
 				(struct ieee80211_tim_ie *)&tim_ie[2];
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/ti/wlcore/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/ti/wlcore/main.c
@@ -2552,24 +2552,24 @@
 	if (test_bit(WL1271_FLAG_RECOVERY_IN_PROGRESS, &wl->flags) ||
 	    test_bit(WLVIF_FLAG_INITIALIZED, &wlvif->flags)) {
 		ret = -EBUSY;
-		goto out;
+		goto out_unlock;
 	}
 
 
 	ret = wl12xx_init_vif_data(wl, vif);
 	if (ret < 0)
-		goto out;
+		goto out_unlock;
 
 	wlvif->wl = wl;
 	role_type = wl12xx_get_role_type(wl, wlvif);
 	if (role_type == WL12XX_INVALID_ROLE_TYPE) {
 		ret = -EINVAL;
-		goto out;
+		goto out_unlock;
 	}
 
 	ret = wlcore_allocate_hw_queue_base(wl, wlvif);
 	if (ret < 0)
-		goto out;
+		goto out_unlock;
 
 	/*
 	 * TODO: after the nvs issue will be solved, move this block
@@ -2584,7 +2584,7 @@
 
 		ret = wl12xx_init_fw(wl);
 		if (ret < 0)
-			goto out;
+			goto out_unlock;
 	}
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/virt_wifi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/virt_wifi.c
@@ -136,6 +136,9 @@
 /* Assigned at module init. Guaranteed locally-administered and unicast. */
 static u8 fake_router_bssid[ETH_ALEN] __ro_after_init = {};
 
+#define VIRT_WIFI_SSID "VirtWifi"
+#define VIRT_WIFI_SSID_LEN 8
+
 static void virt_wifi_inform_bss(struct wiphy *wiphy)
 {
 	u64 tsf = div_u64(ktime_get_boottime_ns(), 1000);
@@ -146,8 +149,8 @@
 		u8 ssid[8];
 	} __packed ssid = {
 		.tag = WLAN_EID_SSID,
-		.len = 8,
-		.ssid = "VirtWifi",
+		.len = VIRT_WIFI_SSID_LEN,
+		.ssid = VIRT_WIFI_SSID,
 	};
 
 	informed_bss = cfg80211_inform_bss(wiphy, &channel_5ghz,
@@ -213,6 +216,8 @@
 	struct net_device *upperdev;
 	u32 tx_packets;
 	u32 tx_failed;
+	u32 connect_requested_ssid_len;
+	u8 connect_requested_ssid[IEEE80211_MAX_SSID_LEN];
 	u8 connect_requested_bss[ETH_ALEN];
 	bool is_up;
 	bool is_connected;
@@ -229,6 +234,12 @@
 	if (priv->being_deleted || !priv->is_up)
 		return -EBUSY;
 
+	if (!sme->ssid)
+		return -EINVAL;
+
+	priv->connect_requested_ssid_len = sme->ssid_len;
+	memcpy(priv->connect_requested_ssid, sme->ssid, sme->ssid_len);
+
 	could_schedule = schedule_delayed_work(&priv->connect, HZ * 2);
 	if (!could_schedule)
 		return -EBUSY;
@@ -252,12 +263,15 @@
 		container_of(work, struct virt_wifi_netdev_priv, connect.work);
 	u8 *requested_bss = priv->connect_requested_bss;
 	bool right_addr = ether_addr_equal(requested_bss, fake_router_bssid);
+	bool right_ssid = priv->connect_requested_ssid_len == VIRT_WIFI_SSID_LEN &&
+			  !memcmp(priv->connect_requested_ssid, VIRT_WIFI_SSID,
+				  priv->connect_requested_ssid_len);
 	u16 status = WLAN_STATUS_SUCCESS;
 
 	if (is_zero_ether_addr(requested_bss))
 		requested_bss = NULL;
 
-	if (!priv->is_up || (requested_bss && !right_addr))
+	if (!priv->is_up || (requested_bss && !right_addr) || !right_ssid)
 		status = WLAN_STATUS_UNSPECIFIED_FAILURE;
 	else
 		priv->is_connected = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wireless/wl3501_cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wireless/wl3501_cs.c
@@ -1328,7 +1328,7 @@
 	} else {
 		++dev->stats.tx_packets;
 		dev->stats.tx_bytes += skb->len;
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 
 		if (this->tx_buffer_cnt < 2)
 			netif_stop_queue(dev);
@@ -1862,6 +1862,7 @@
 {
 	struct net_device *dev;
 	struct wl3501_card *this;
+	int ret;
 
 	/* The io structure describes IO port mapping */
 	p_dev->resource[0]->end	= 16;
@@ -1873,8 +1874,7 @@
 
 	dev = alloc_etherdev(sizeof(struct wl3501_card));
 	if (!dev)
-		goto out_link;
-
+		return -ENOMEM;
 
 	dev->netdev_ops		= &wl3501_netdev_ops;
 	dev->watchdog_timeo	= 5 * HZ;
@@ -1887,9 +1887,15 @@
 	netif_stop_queue(dev);
 	p_dev->priv = dev;
 
-	return wl3501_config(p_dev);
-out_link:
-	return -ENOMEM;
+	ret = wl3501_config(p_dev);
+	if (ret)
+		goto out_free_etherdev;
+
+	return 0;
+
+out_free_etherdev:
+	free_netdev(dev);
+	return ret;
 }
 
 static int wl3501_config(struct pcmcia_device *link)
@@ -1945,8 +1951,7 @@
 		goto failed;
 	}
 
-	for (i = 0; i < 6; i++)
-		dev->dev_addr[i] = ((char *)&this->mac_addr)[i];
+	eth_hw_addr_set(dev, this->mac_addr);
 
 	/* print probe information */
 	printk(KERN_INFO "%s: wl3501 @ 0x%3.3x, IRQ %d, "
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/Kconfig
@@ -70,7 +70,7 @@
 
 config IOSM
 	tristate "IOSM Driver for Intel M.2 WWAN Device"
-	depends on INTEL_IOMMU
+	depends on PCI
 	help
 	  This driver enables Intel M.2 WWAN Device communication.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/iosm/iosm_ipc_mmio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/iosm/iosm_ipc_mmio.c
@@ -102,7 +102,7 @@
 			break;
 
 		msleep(20);
-	} while (retries-- > 0);
+	} while (--retries > 0);
 
 	if (!retries) {
 		dev_err(ipc_mmio->dev, "invalid exec stage %X", stage);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/iosm/iosm_ipc_mux_codec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/iosm/iosm_ipc_mux_codec.c
@@ -830,8 +830,7 @@
 			ipc_mux->ul_data_pend_bytes);
 
 	/* Reset the skb settings. */
-	skb->tail = 0;
-	skb->len = 0;
+	skb_trim(skb, 0);
 
 	/* Add the consumed ADB to the free list. */
 	skb_queue_tail((&ipc_mux->ul_adb.free_list), skb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/iosm/iosm_ipc_pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/iosm/iosm_ipc_pcie.c
@@ -6,6 +6,7 @@
 #include <linux/acpi.h>
 #include <linux/bitfield.h>
 #include <linux/module.h>
+#include <linux/suspend.h>
 #include <net/rtnetlink.h>
 
 #include "iosm_ipc_imem.h"
@@ -18,6 +19,7 @@
 /* WWAN GUID */
 static guid_t wwan_acpi_guid = GUID_INIT(0xbad01b75, 0x22a8, 0x4f48, 0x87, 0x92,
 				       0xbd, 0xde, 0x94, 0x67, 0x74, 0x7d);
+static bool pci_registered;
 
 static void ipc_pcie_resources_release(struct iosm_pcie *ipc_pcie)
 {
@@ -232,6 +234,7 @@
  */
 static enum ipc_pcie_sleep_state ipc_pcie_read_bios_cfg(struct device *dev)
 {
+	enum ipc_pcie_sleep_state sleep_state = IPC_PCIE_D0L12;
 	union acpi_object *object;
 	acpi_handle handle_acpi;
 
@@ -242,18 +245,23 @@
 	}
 
 	object = acpi_evaluate_dsm(handle_acpi, &wwan_acpi_guid, 0, 3, NULL);
+	if (!object)
+		goto default_ret;
+
+	if (object->integer.value == 3)
+		sleep_state = IPC_PCIE_D3L2;
 
-	if (object && object->integer.value == 3)
-		return IPC_PCIE_D3L2;
+	ACPI_FREE(object);
 
 default_ret:
-	return IPC_PCIE_D0L12;
+	return sleep_state;
 }
 
 static int ipc_pcie_probe(struct pci_dev *pci,
 			  const struct pci_device_id *pci_id)
 {
 	struct iosm_pcie *ipc_pcie = kzalloc(sizeof(*ipc_pcie), GFP_KERNEL);
+	int ret;
 
 	pr_debug("Probing device 0x%X from the vendor 0x%X", pci_id->device,
 		 pci_id->vendor);
@@ -286,6 +294,12 @@
 		goto pci_enable_fail;
 	}
 
+	ret = dma_set_mask(ipc_pcie->dev, DMA_BIT_MASK(64));
+	if (ret) {
+		dev_err(ipc_pcie->dev, "Could not set PCI DMA mask: %d", ret);
+		return ret;
+	}
+
 	ipc_pcie_config_aspm(ipc_pcie);
 	dev_dbg(ipc_pcie->dev, "PCIe device enabled.");
 
@@ -340,6 +354,9 @@
 
 	ipc_imem_pm_s2idle_sleep(ipc_pcie->imem, true);
 
+	/* Let PCI core know this device should stay at D0 */
+	pci_save_state(ipc_pcie->pci);
+
 	return 0;
 }
 
@@ -479,7 +496,6 @@
 	},
 	.id_table = iosm_ipc_ids,
 };
-module_pci_driver(iosm_ipc_driver);
 
 int ipc_pcie_addr_map(struct iosm_pcie *ipc_pcie, unsigned char *data,
 		      size_t size, dma_addr_t *mapping, int direction)
@@ -561,3 +577,56 @@
 	IPC_CB(skb)->mapping = 0;
 	dev_kfree_skb(skb);
 }
+
+static int pm_notify(struct notifier_block *nb, unsigned long mode, void *_unused)
+{
+	if (mode == PM_HIBERNATION_PREPARE || mode == PM_RESTORE_PREPARE) {
+		if (pci_registered) {
+			pci_unregister_driver(&iosm_ipc_driver);
+			pci_registered = false;
+		}
+	} else if (mode == PM_POST_HIBERNATION || mode == PM_POST_RESTORE) {
+		if (!pci_registered) {
+			int ret;
+
+			ret = pci_register_driver(&iosm_ipc_driver);
+			if (ret) {
+				pr_err(KBUILD_MODNAME ": unable to re-register PCI driver: %d\n",
+				       ret);
+			} else {
+				pci_registered = true;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static struct notifier_block pm_notifier = {
+	.notifier_call = pm_notify,
+};
+
+static int __init iosm_ipc_driver_init(void)
+{
+	int ret;
+
+	ret = pci_register_driver(&iosm_ipc_driver);
+	if (ret)
+		return ret;
+
+	pci_registered = true;
+
+	register_pm_notifier(&pm_notifier);
+
+	return 0;
+}
+module_init(iosm_ipc_driver_init);
+
+static void __exit iosm_ipc_driver_exit(void)
+{
+	unregister_pm_notifier(&pm_notifier);
+
+	if (pci_registered)
+		pci_unregister_driver(&iosm_ipc_driver);
+}
+module_exit(iosm_ipc_driver_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/iosm/iosm_ipc_protocol.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/iosm/iosm_ipc_protocol.h
@@ -122,7 +122,7 @@
 	struct iosm_imem *imem;
 	struct ipc_rsp *rsp_ring[IPC_MEM_MSG_ENTRIES];
 	struct device *dev;
-	phys_addr_t phy_ap_shm;
+	dma_addr_t phy_ap_shm;
 	u32 old_msg_tail;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c
@@ -372,8 +372,6 @@
 struct sk_buff *ipc_protocol_dl_td_process(struct iosm_protocol *ipc_protocol,
 					   struct ipc_pipe *pipe)
 {
-	u32 tail =
-		le32_to_cpu(ipc_protocol->p_ap_shm->tail_array[pipe->pipe_nr]);
 	struct ipc_protocol_td *p_td;
 	struct sk_buff *skb;
 
@@ -401,14 +399,6 @@
 		ipc_pcie_kfree_skb(ipc_protocol->pcie, skb);
 		skb = NULL;
 		goto ret;
-	}
-
-	if (!IPC_CB(skb)) {
-		dev_err(ipc_protocol->dev, "pipe# %d, tail: %d skb_cb is NULL",
-			pipe->pipe_nr, tail);
-		ipc_pcie_kfree_skb(ipc_protocol->pcie, skb);
-		skb = NULL;
-		goto ret;
 	}
 
 	if (p_td->buffer.address != IPC_CB(skb)->mapping) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/iosm/iosm_ipc_wwan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/iosm/iosm_ipc_wwan.c
@@ -167,6 +167,7 @@
 	iosm_dev->max_mtu = ETH_MAX_MTU;
 
 	iosm_dev->flags = IFF_POINTOPOINT | IFF_NOARP;
+	iosm_dev->needs_free_netdev = true;
 
 	iosm_dev->netdev_ops = &ipc_inm_ops;
 }
@@ -322,15 +323,16 @@
 	ipc_wwan->dev = dev;
 	ipc_wwan->ipc_imem = ipc_imem;
 
+	mutex_init(&ipc_wwan->if_mutex);
+
 	/* WWAN core will create a netdev for the default IP MUX channel */
 	if (wwan_register_ops(ipc_wwan->dev, &iosm_wwan_ops, ipc_wwan,
 			      IP_MUX_SESSION_DEFAULT)) {
+		mutex_destroy(&ipc_wwan->if_mutex);
 		kfree(ipc_wwan);
 		return NULL;
 	}
 
-	mutex_init(&ipc_wwan->if_mutex);
-
 	return ipc_wwan;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/mhi_wwan_mbim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/mhi_wwan_mbim.c
@@ -209,7 +209,7 @@
 	if (mbim->rx_seq + 1 != le16_to_cpu(nth16->wSequence) &&
 	    (mbim->rx_seq || le16_to_cpu(nth16->wSequence)) &&
 	    !(mbim->rx_seq == 0xffff && !le16_to_cpu(nth16->wSequence))) {
-		net_err_ratelimited("sequence number glitch prev=%d curr=%d\n",
+		net_dbg_ratelimited("sequence number glitch prev=%d curr=%d\n",
 				    mbim->rx_seq, le16_to_cpu(nth16->wSequence));
 	}
 	mbim->rx_seq = le16_to_cpu(nth16->wSequence);
@@ -385,13 +385,13 @@
 	int err;
 
 	while (!mhi_queue_is_full(mdev, DMA_FROM_DEVICE)) {
-		struct sk_buff *skb = alloc_skb(MHI_DEFAULT_MRU, GFP_KERNEL);
+		struct sk_buff *skb = alloc_skb(mbim->mru, GFP_KERNEL);
 
 		if (unlikely(!skb))
 			break;
 
 		err = mhi_queue_skb(mdev, DMA_FROM_DEVICE, skb,
-				    MHI_DEFAULT_MRU, MHI_EOT);
+				    mbim->mru, MHI_EOT);
 		if (unlikely(err)) {
 			kfree_skb(skb);
 			break;
@@ -582,6 +582,7 @@
 	ndev->min_mtu = ETH_MIN_MTU;
 	ndev->max_mtu = MHI_MAX_BUF_SZ - ndev->needed_headroom;
 	ndev->tx_queue_len = 1000;
+	ndev->needs_free_netdev = true;
 }
 
 static const struct wwan_ops mhi_mbim_wwan_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/wwan_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/wwan_core.c
@@ -927,7 +927,7 @@
 
 static struct rtnl_link_ops wwan_rtnl_link_ops __read_mostly = {
 	.kind = "wwan",
-	.maxtype = __IFLA_WWAN_MAX,
+	.maxtype = IFLA_WWAN_MAX,
 	.alloc = wwan_rtnl_alloc,
 	.validate = wwan_rtnl_validate,
 	.newlink = wwan_rtnl_newlink,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/wwan/wwan_hwsim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/wwan/wwan_hwsim.c
@@ -310,7 +310,7 @@
 	return ERR_PTR(err);
 
 err_free_dev:
-	kfree(dev);
+	put_device(&dev->dev);
 
 	return ERR_PTR(err);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netback/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netback/common.h
@@ -48,7 +48,6 @@
 #include <linux/debugfs.h>
 
 typedef unsigned int pending_ring_idx_t;
-#define INVALID_PENDING_RING_IDX (~0U)
 
 struct pending_tx_info {
 	struct xen_netif_tx_request req; /* tx request */
@@ -82,8 +81,6 @@
 /* Discriminate from any valid pending_idx value. */
 #define INVALID_PENDING_IDX 0xFFFF
 
-#define MAX_BUFFER_OFFSET XEN_PAGE_SIZE
-
 #define MAX_PENDING_REQS XEN_NETIF_TX_RING_SIZE
 
 /* The maximum number of frags is derived from the size of a grant (same
@@ -169,7 +166,7 @@
 	struct pending_tx_info pending_tx_info[MAX_PENDING_REQS];
 	grant_handle_t grant_tx_handle[MAX_PENDING_REQS];
 
-	struct gnttab_copy tx_copy_ops[MAX_PENDING_REQS];
+	struct gnttab_copy tx_copy_ops[2 * MAX_PENDING_REQS];
 	struct gnttab_map_grant_ref tx_map_ops[MAX_PENDING_REQS];
 	struct gnttab_unmap_grant_ref tx_unmap_ops[MAX_PENDING_REQS];
 	/* passed to gnttab_[un]map_refs with pages under (un)mapping */
@@ -203,6 +200,7 @@
 	unsigned int rx_queue_max;
 	unsigned int rx_queue_len;
 	unsigned long last_rx_time;
+	unsigned int rx_slots_needed;
 	bool stalled;
 
 	struct xenvif_copy_state rx_copy;
@@ -366,11 +364,6 @@
 int xenvif_xenbus_init(void);
 void xenvif_xenbus_fini(void);
 
-int xenvif_schedulable(struct xenvif *vif);
-
-int xenvif_queue_stopped(struct xenvif_queue *queue);
-void xenvif_wake_queue(struct xenvif_queue *queue);
-
 /* (Un)Map communication rings. */
 void xenvif_unmap_frontend_data_rings(struct xenvif_queue *queue);
 int xenvif_map_frontend_data_rings(struct xenvif_queue *queue,
@@ -393,8 +386,7 @@
 irqreturn_t xenvif_ctrl_irq_fn(int irq, void *data);
 
 bool xenvif_have_rx_work(struct xenvif_queue *queue, bool test_kthread);
-void xenvif_rx_action(struct xenvif_queue *queue);
-void xenvif_rx_queue_tail(struct xenvif_queue *queue, struct sk_buff *skb);
+bool xenvif_rx_queue_tail(struct xenvif_queue *queue, struct sk_buff *skb);
 
 void xenvif_carrier_on(struct xenvif *vif);
 
@@ -402,9 +394,6 @@
 void xenvif_zerocopy_callback(struct sk_buff *skb, struct ubuf_info *ubuf,
 			      bool zerocopy_success);
 
-/* Unmap a pending page and release it back to the guest */
-void xenvif_idx_unmap(struct xenvif_queue *queue, u16 pending_idx);
-
 static inline pending_ring_idx_t nr_pending_reqs(struct xenvif_queue *queue)
 {
 	return MAX_PENDING_REQS -
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netback/hash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netback/hash.c
@@ -95,7 +95,7 @@
 
 static void xenvif_flush_hash(struct xenvif *vif)
 {
-	struct xenvif_hash_cache_entry *entry;
+	struct xenvif_hash_cache_entry *entry, *n;
 	unsigned long flags;
 
 	if (xenvif_hash_cache_size == 0)
@@ -103,8 +103,7 @@
 
 	spin_lock_irqsave(&vif->hash.cache.lock, flags);
 
-	list_for_each_entry_rcu(entry, &vif->hash.cache.list, link,
-				lockdep_is_held(&vif->hash.cache.lock)) {
+	list_for_each_entry_safe(entry, n, &vif->hash.cache.list, link) {
 		list_del_rcu(&entry->link);
 		vif->hash.cache.count--;
 		kfree_rcu(entry, rcu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netback/interface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netback/interface.c
@@ -41,9 +41,6 @@
 #include <asm/xen/hypercall.h>
 #include <xen/balloon.h>
 
-#define XENVIF_QUEUE_LENGTH 32
-#define XENVIF_NAPI_WEIGHT  64
-
 /* Number of bytes allowed on the internal guest Rx queue. */
 #define XENVIF_RX_QUEUE_BYTES (XEN_NETIF_RX_RING_SIZE/2 * PAGE_SIZE)
 
@@ -70,7 +67,7 @@
 	wake_up(&queue->dealloc_wq);
 }
 
-int xenvif_schedulable(struct xenvif *vif)
+static int xenvif_schedulable(struct xenvif *vif)
 {
 	return netif_running(vif->dev) &&
 		test_bit(VIF_STATUS_CONNECTED, &vif->status) &&
@@ -178,20 +175,6 @@
 	return IRQ_HANDLED;
 }
 
-int xenvif_queue_stopped(struct xenvif_queue *queue)
-{
-	struct net_device *dev = queue->vif->dev;
-	unsigned int id = queue->id;
-	return netif_tx_queue_stopped(netdev_get_tx_queue(dev, id));
-}
-
-void xenvif_wake_queue(struct xenvif_queue *queue)
-{
-	struct net_device *dev = queue->vif->dev;
-	unsigned int id = queue->id;
-	netif_tx_wake_queue(netdev_get_tx_queue(dev, id));
-}
-
 static u16 xenvif_select_queue(struct net_device *dev, struct sk_buff *skb,
 			       struct net_device *sb_dev)
 {
@@ -269,14 +252,16 @@
 	if (vif->hash.alg == XEN_NETIF_CTRL_HASH_ALGORITHM_NONE)
 		skb_clear_hash(skb);
 
-	xenvif_rx_queue_tail(queue, skb);
+	if (!xenvif_rx_queue_tail(queue, skb))
+		goto drop;
+
 	xenvif_kick_thread(queue);
 
 	return NETDEV_TX_OK;
 
  drop:
 	vif->dev->stats.tx_dropped++;
-	dev_kfree_skb(skb);
+	dev_kfree_skb_any(skb);
 	return NETDEV_TX_OK;
 }
 
@@ -540,8 +525,6 @@
 	dev->features = dev->hw_features | NETIF_F_RXCSUM;
 	dev->ethtool_ops = &xenvif_ethtool_ops;
 
-	dev->tx_queue_len = XENVIF_QUEUE_LENGTH;
-
 	dev->min_mtu = ETH_MIN_MTU;
 	dev->max_mtu = ETH_MAX_MTU - VLAN_ETH_HLEN;
 
@@ -737,7 +720,7 @@
 	atomic_set(&queue->inflight_packets, 0);
 
 	netif_napi_add(queue->vif->dev, &queue->napi, xenvif_poll,
-			XENVIF_NAPI_WEIGHT);
+			NAPI_POLL_WEIGHT);
 
 	queue->stalled = true;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netback/netback.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netback/netback.c
@@ -104,13 +104,14 @@
 module_param(provides_xdp_headroom, bool, 0644);
 
 static void xenvif_idx_release(struct xenvif_queue *queue, u16 pending_idx,
-			       u8 status);
+			       s8 status);
 
 static void make_tx_response(struct xenvif_queue *queue,
-			     struct xen_netif_tx_request *txp,
+			     const struct xen_netif_tx_request *txp,
 			     unsigned int extra_count,
-			     s8       st);
-static void push_tx_responses(struct xenvif_queue *queue);
+			     s8 status);
+
+static void xenvif_idx_unmap(struct xenvif_queue *queue, u16 pending_idx);
 
 static inline int tx_work_todo(struct xenvif_queue *queue);
 
@@ -206,13 +207,9 @@
 			  unsigned int extra_count, RING_IDX end)
 {
 	RING_IDX cons = queue->tx.req_cons;
-	unsigned long flags;
 
 	do {
-		spin_lock_irqsave(&queue->response_lock, flags);
 		make_tx_response(queue, txp, extra_count, XEN_NETIF_RSP_ERROR);
-		push_tx_responses(queue);
-		spin_unlock_irqrestore(&queue->response_lock, flags);
 		if (cons == end)
 			break;
 		RING_COPY_REQUEST(&queue->tx, cons++, txp);
@@ -330,10 +327,14 @@
 
 
 struct xenvif_tx_cb {
-	u16 pending_idx;
+	u16 copy_pending_idx[XEN_NETBK_LEGACY_SLOTS_MAX + 1];
+	u8 copy_count;
+	u32 split_mask;
 };
 
 #define XENVIF_TX_CB(skb) ((struct xenvif_tx_cb *)(skb)->cb)
+#define copy_pending_idx(skb, i) (XENVIF_TX_CB(skb)->copy_pending_idx[i])
+#define copy_count(skb) (XENVIF_TX_CB(skb)->copy_count)
 
 static inline void xenvif_tx_create_map_op(struct xenvif_queue *queue,
 					   u16 pending_idx,
@@ -356,6 +357,8 @@
 	struct sk_buff *skb =
 		alloc_skb(size + NET_SKB_PAD + NET_IP_ALIGN,
 			  GFP_ATOMIC | __GFP_NOWARN);
+
+	BUILD_BUG_ON(sizeof(*XENVIF_TX_CB(skb)) > sizeof(skb->cb));
 	if (unlikely(skb == NULL))
 		return NULL;
 
@@ -368,52 +371,152 @@
 	return skb;
 }
 
-static struct gnttab_map_grant_ref *xenvif_get_requests(struct xenvif_queue *queue,
-							struct sk_buff *skb,
-							struct xen_netif_tx_request *txp,
-							struct gnttab_map_grant_ref *gop,
-							unsigned int frag_overflow,
-							struct sk_buff *nskb)
+static void xenvif_get_requests(struct xenvif_queue *queue,
+				struct sk_buff *skb,
+				struct xen_netif_tx_request *first,
+				struct xen_netif_tx_request *txfrags,
+			        unsigned *copy_ops,
+			        unsigned *map_ops,
+				unsigned int frag_overflow,
+				struct sk_buff *nskb,
+				unsigned int extra_count,
+				unsigned int data_len)
 {
 	struct skb_shared_info *shinfo = skb_shinfo(skb);
 	skb_frag_t *frags = shinfo->frags;
-	u16 pending_idx = XENVIF_TX_CB(skb)->pending_idx;
-	int start;
+	u16 pending_idx;
 	pending_ring_idx_t index;
 	unsigned int nr_slots;
+	struct gnttab_copy *cop = queue->tx_copy_ops + *copy_ops;
+	struct gnttab_map_grant_ref *gop = queue->tx_map_ops + *map_ops;
+	struct xen_netif_tx_request *txp = first;
+
+	nr_slots = shinfo->nr_frags + frag_overflow + 1;
+
+	copy_count(skb) = 0;
+	XENVIF_TX_CB(skb)->split_mask = 0;
+
+	/* Create copy ops for exactly data_len bytes into the skb head. */
+	__skb_put(skb, data_len);
+	while (data_len > 0) {
+		int amount = data_len > txp->size ? txp->size : data_len;
+		bool split = false;
+
+		cop->source.u.ref = txp->gref;
+		cop->source.domid = queue->vif->domid;
+		cop->source.offset = txp->offset;
+
+		cop->dest.domid = DOMID_SELF;
+		cop->dest.offset = (offset_in_page(skb->data +
+						   skb_headlen(skb) -
+						   data_len)) & ~XEN_PAGE_MASK;
+		cop->dest.u.gmfn = virt_to_gfn(skb->data + skb_headlen(skb)
+				               - data_len);
+
+		/* Don't cross local page boundary! */
+		if (cop->dest.offset + amount > XEN_PAGE_SIZE) {
+			amount = XEN_PAGE_SIZE - cop->dest.offset;
+			XENVIF_TX_CB(skb)->split_mask |= 1U << copy_count(skb);
+			split = true;
+		}
+
+		cop->len = amount;
+		cop->flags = GNTCOPY_source_gref;
+
+		index = pending_index(queue->pending_cons);
+		pending_idx = queue->pending_ring[index];
+		callback_param(queue, pending_idx).ctx = NULL;
+		copy_pending_idx(skb, copy_count(skb)) = pending_idx;
+		if (!split)
+			copy_count(skb)++;
+
+		cop++;
+		data_len -= amount;
+
+		if (amount == txp->size) {
+			/* The copy op covered the full tx_request */
+
+			memcpy(&queue->pending_tx_info[pending_idx].req,
+			       txp, sizeof(*txp));
+			queue->pending_tx_info[pending_idx].extra_count =
+				(txp == first) ? extra_count : 0;
 
-	nr_slots = shinfo->nr_frags;
+			if (txp == first)
+				txp = txfrags;
+			else
+				txp++;
+			queue->pending_cons++;
+			nr_slots--;
+		} else {
+			/* The copy op partially covered the tx_request.
+			 * The remainder will be mapped or copied in the next
+			 * iteration.
+			 */
+			txp->offset += amount;
+			txp->size -= amount;
+		}
+	}
 
-	/* Skip first skb fragment if it is on same page as header fragment. */
-	start = (frag_get_pending_idx(&shinfo->frags[0]) == pending_idx);
+	for (shinfo->nr_frags = 0; nr_slots > 0 && shinfo->nr_frags < MAX_SKB_FRAGS;
+	     nr_slots--) {
+		if (unlikely(!txp->size)) {
+			make_tx_response(queue, txp, 0, XEN_NETIF_RSP_OKAY);
+			++txp;
+			continue;
+		}
 
-	for (shinfo->nr_frags = start; shinfo->nr_frags < nr_slots;
-	     shinfo->nr_frags++, txp++, gop++) {
 		index = pending_index(queue->pending_cons++);
 		pending_idx = queue->pending_ring[index];
-		xenvif_tx_create_map_op(queue, pending_idx, txp, 0, gop);
+		xenvif_tx_create_map_op(queue, pending_idx, txp,
+				        txp == first ? extra_count : 0, gop);
 		frag_set_pending_idx(&frags[shinfo->nr_frags], pending_idx);
+		++shinfo->nr_frags;
+		++gop;
+
+		if (txp == first)
+			txp = txfrags;
+		else
+			txp++;
 	}
 
-	if (frag_overflow) {
+	if (nr_slots > 0) {
 
 		shinfo = skb_shinfo(nskb);
 		frags = shinfo->frags;
 
-		for (shinfo->nr_frags = 0; shinfo->nr_frags < frag_overflow;
-		     shinfo->nr_frags++, txp++, gop++) {
+		for (shinfo->nr_frags = 0; shinfo->nr_frags < nr_slots; ++txp) {
+			if (unlikely(!txp->size)) {
+				make_tx_response(queue, txp, 0,
+						 XEN_NETIF_RSP_OKAY);
+				continue;
+			}
+
 			index = pending_index(queue->pending_cons++);
 			pending_idx = queue->pending_ring[index];
 			xenvif_tx_create_map_op(queue, pending_idx, txp, 0,
 						gop);
 			frag_set_pending_idx(&frags[shinfo->nr_frags],
 					     pending_idx);
+			++shinfo->nr_frags;
+			++gop;
+		}
+
+		if (shinfo->nr_frags) {
+			skb_shinfo(skb)->frag_list = nskb;
+			nskb = NULL;
 		}
+	}
 
-		skb_shinfo(skb)->frag_list = nskb;
+	if (nskb) {
+		/* A frag_list skb was allocated but it is no longer needed
+		 * because enough slots were converted to copy ops above or some
+		 * were empty.
+		 */
+		kfree_skb(nskb);
 	}
 
-	return gop;
+	(*copy_ops) = cop - queue->tx_copy_ops;
+	(*map_ops) = gop - queue->tx_map_ops;
 }
 
 static inline void xenvif_grant_handle_set(struct xenvif_queue *queue,
@@ -449,7 +552,7 @@
 			       struct gnttab_copy **gopp_copy)
 {
 	struct gnttab_map_grant_ref *gop_map = *gopp_map;
-	u16 pending_idx = XENVIF_TX_CB(skb)->pending_idx;
+	u16 pending_idx;
 	/* This always points to the shinfo of the skb being checked, which
 	 * could be either the first or the one on the frag_list
 	 */
@@ -460,24 +563,44 @@
 	struct skb_shared_info *first_shinfo = NULL;
 	int nr_frags = shinfo->nr_frags;
 	const bool sharedslot = nr_frags &&
-				frag_get_pending_idx(&shinfo->frags[0]) == pending_idx;
-	int i, err;
-
-	/* Check status of header. */
-	err = (*gopp_copy)->status;
-	if (unlikely(err)) {
-		if (net_ratelimit())
-			netdev_dbg(queue->vif->dev,
-				   "Grant copy of header failed! status: %d pending_idx: %u ref: %u\n",
-				   (*gopp_copy)->status,
-				   pending_idx,
-				   (*gopp_copy)->source.u.ref);
-		/* The first frag might still have this slot mapped */
-		if (!sharedslot)
-			xenvif_idx_release(queue, pending_idx,
-					   XEN_NETIF_RSP_ERROR);
+				frag_get_pending_idx(&shinfo->frags[0]) ==
+				    copy_pending_idx(skb, copy_count(skb) - 1);
+	int i, err = 0;
+
+	for (i = 0; i < copy_count(skb); i++) {
+		int newerr;
+
+		/* Check status of header. */
+		pending_idx = copy_pending_idx(skb, i);
+
+		newerr = (*gopp_copy)->status;
+
+		/* Split copies need to be handled together. */
+		if (XENVIF_TX_CB(skb)->split_mask & (1U << i)) {
+			(*gopp_copy)++;
+			if (!newerr)
+				newerr = (*gopp_copy)->status;
+		}
+		if (likely(!newerr)) {
+			/* The first frag might still have this slot mapped */
+			if (i < copy_count(skb) - 1 || !sharedslot)
+				xenvif_idx_release(queue, pending_idx,
+						   XEN_NETIF_RSP_OKAY);
+		} else {
+			err = newerr;
+			if (net_ratelimit())
+				netdev_dbg(queue->vif->dev,
+					   "Grant copy of header failed! status: %d pending_idx: %u ref: %u\n",
+					   (*gopp_copy)->status,
+					   pending_idx,
+					   (*gopp_copy)->source.u.ref);
+			/* The first frag might still have this slot mapped */
+			if (i < copy_count(skb) - 1 || !sharedslot)
+				xenvif_idx_release(queue, pending_idx,
+						   XEN_NETIF_RSP_ERROR);
+		}
+		(*gopp_copy)++;
 	}
-	(*gopp_copy)++;
 
 check_frags:
 	for (i = 0; i < nr_frags; i++, gop_map++) {
@@ -524,14 +647,6 @@
 		if (err)
 			continue;
 
-		/* First error: if the header haven't shared a slot with the
-		 * first frag, release it as well.
-		 */
-		if (!sharedslot)
-			xenvif_idx_release(queue,
-					   XENVIF_TX_CB(skb)->pending_idx,
-					   XEN_NETIF_RSP_OKAY);
-
 		/* Invalidate preceding fragments of this skb. */
 		for (j = 0; j < i; j++) {
 			pending_idx = frag_get_pending_idx(&shinfo->frags[j]);
@@ -801,7 +916,6 @@
 				     unsigned *copy_ops,
 				     unsigned *map_ops)
 {
-	struct gnttab_map_grant_ref *gop = queue->tx_map_ops;
 	struct sk_buff *skb, *nskb;
 	int ret;
 	unsigned int frag_overflow;
@@ -867,7 +981,6 @@
 					 (ret == 0) ?
 					 XEN_NETIF_RSP_OKAY :
 					 XEN_NETIF_RSP_ERROR);
-			push_tx_responses(queue);
 			continue;
 		}
 
@@ -879,12 +992,15 @@
 
 			make_tx_response(queue, &txreq, extra_count,
 					 XEN_NETIF_RSP_OKAY);
-			push_tx_responses(queue);
 			continue;
 		}
 
+		data_len = (txreq.size > XEN_NETBACK_TX_COPY_LEN) ?
+			XEN_NETBACK_TX_COPY_LEN : txreq.size;
+
 		ret = xenvif_count_requests(queue, &txreq, extra_count,
 					    txfrags, work_to_do);
+
 		if (unlikely(ret < 0))
 			break;
 
@@ -899,10 +1015,8 @@
 
 		/* No crossing a page as the payload mustn't fragment. */
 		if (unlikely((txreq.offset + txreq.size) > XEN_PAGE_SIZE)) {
-			netdev_err(queue->vif->dev,
-				   "txreq.offset: %u, size: %u, end: %lu\n",
-				   txreq.offset, txreq.size,
-				   (unsigned long)(txreq.offset&~XEN_PAGE_MASK) + txreq.size);
+			netdev_err(queue->vif->dev, "Cross page boundary, txreq.offset: %u, size: %u\n",
+				   txreq.offset, txreq.size);
 			xenvif_fatal_tx_err(queue->vif);
 			break;
 		}
@@ -910,9 +1024,8 @@
 		index = pending_index(queue->pending_cons);
 		pending_idx = queue->pending_ring[index];
 
-		data_len = (txreq.size > XEN_NETBACK_TX_COPY_LEN &&
-			    ret < XEN_NETBK_LEGACY_SLOTS_MAX) ?
-			XEN_NETBACK_TX_COPY_LEN : txreq.size;
+		if (ret >= XEN_NETBK_LEGACY_SLOTS_MAX - 1 && data_len < txreq.size)
+			data_len = txreq.size;
 
 		skb = xenvif_alloc_skb(data_len);
 		if (unlikely(skb == NULL)) {
@@ -923,8 +1036,6 @@
 		}
 
 		skb_shinfo(skb)->nr_frags = ret;
-		if (data_len < txreq.size)
-			skb_shinfo(skb)->nr_frags++;
 		/* At this point shinfo->nr_frags is in fact the number of
 		 * slots, which can be as large as XEN_NETBK_LEGACY_SLOTS_MAX.
 		 */
@@ -986,54 +1097,19 @@
 					     type);
 		}
 
-		XENVIF_TX_CB(skb)->pending_idx = pending_idx;
-
-		__skb_put(skb, data_len);
-		queue->tx_copy_ops[*copy_ops].source.u.ref = txreq.gref;
-		queue->tx_copy_ops[*copy_ops].source.domid = queue->vif->domid;
-		queue->tx_copy_ops[*copy_ops].source.offset = txreq.offset;
-
-		queue->tx_copy_ops[*copy_ops].dest.u.gmfn =
-			virt_to_gfn(skb->data);
-		queue->tx_copy_ops[*copy_ops].dest.domid = DOMID_SELF;
-		queue->tx_copy_ops[*copy_ops].dest.offset =
-			offset_in_page(skb->data) & ~XEN_PAGE_MASK;
-
-		queue->tx_copy_ops[*copy_ops].len = data_len;
-		queue->tx_copy_ops[*copy_ops].flags = GNTCOPY_source_gref;
-
-		(*copy_ops)++;
-
-		if (data_len < txreq.size) {
-			frag_set_pending_idx(&skb_shinfo(skb)->frags[0],
-					     pending_idx);
-			xenvif_tx_create_map_op(queue, pending_idx, &txreq,
-						extra_count, gop);
-			gop++;
-		} else {
-			frag_set_pending_idx(&skb_shinfo(skb)->frags[0],
-					     INVALID_PENDING_IDX);
-			memcpy(&queue->pending_tx_info[pending_idx].req,
-			       &txreq, sizeof(txreq));
-			queue->pending_tx_info[pending_idx].extra_count =
-				extra_count;
-		}
-
-		queue->pending_cons++;
-
-		gop = xenvif_get_requests(queue, skb, txfrags, gop,
-				          frag_overflow, nskb);
+		xenvif_get_requests(queue, skb, &txreq, txfrags, copy_ops,
+				    map_ops, frag_overflow, nskb, extra_count,
+				    data_len);
 
 		__skb_queue_tail(&queue->tx_queue, skb);
 
 		queue->tx.req_cons = idx;
 
-		if (((gop-queue->tx_map_ops) >= ARRAY_SIZE(queue->tx_map_ops)) ||
+		if ((*map_ops >= ARRAY_SIZE(queue->tx_map_ops)) ||
 		    (*copy_ops >= ARRAY_SIZE(queue->tx_copy_ops)))
 			break;
 	}
 
-	(*map_ops) = gop - queue->tx_map_ops;
 	return;
 }
 
@@ -1112,9 +1188,8 @@
 	while ((skb = __skb_dequeue(&queue->tx_queue)) != NULL) {
 		struct xen_netif_tx_request *txp;
 		u16 pending_idx;
-		unsigned data_len;
 
-		pending_idx = XENVIF_TX_CB(skb)->pending_idx;
+		pending_idx = copy_pending_idx(skb, 0);
 		txp = &queue->pending_tx_info[pending_idx].req;
 
 		/* Check the remap error code. */
@@ -1133,18 +1208,6 @@
 			continue;
 		}
 
-		data_len = skb->len;
-		callback_param(queue, pending_idx).ctx = NULL;
-		if (data_len < txp->size) {
-			/* Append the packet payload as a fragment. */
-			txp->offset += data_len;
-			txp->size -= data_len;
-		} else {
-			/* Schedule a response immediately. */
-			xenvif_idx_release(queue, pending_idx,
-					   XEN_NETIF_RSP_OKAY);
-		}
-
 		if (txp->flags & XEN_NETTXF_csum_blank)
 			skb->ip_summed = CHECKSUM_PARTIAL;
 		else if (txp->flags & XEN_NETTXF_data_validated)
@@ -1331,7 +1394,7 @@
 /* Called after netfront has transmitted */
 int xenvif_tx_action(struct xenvif_queue *queue, int budget)
 {
-	unsigned nr_mops, nr_cops = 0;
+	unsigned nr_mops = 0, nr_cops = 0;
 	int work_done, ret;
 
 	if (unlikely(!tx_work_todo(queue)))
@@ -1364,8 +1427,35 @@
 	return work_done;
 }
 
+static void _make_tx_response(struct xenvif_queue *queue,
+			     const struct xen_netif_tx_request *txp,
+			     unsigned int extra_count,
+			     s8 status)
+{
+	RING_IDX i = queue->tx.rsp_prod_pvt;
+	struct xen_netif_tx_response *resp;
+
+	resp = RING_GET_RESPONSE(&queue->tx, i);
+	resp->id     = txp->id;
+	resp->status = status;
+
+	while (extra_count-- != 0)
+		RING_GET_RESPONSE(&queue->tx, ++i)->status = XEN_NETIF_RSP_NULL;
+
+	queue->tx.rsp_prod_pvt = ++i;
+}
+
+static void push_tx_responses(struct xenvif_queue *queue)
+{
+	int notify;
+
+	RING_PUSH_RESPONSES_AND_CHECK_NOTIFY(&queue->tx, notify);
+	if (notify)
+		notify_remote_via_irq(queue->tx_irq);
+}
+
 static void xenvif_idx_release(struct xenvif_queue *queue, u16 pending_idx,
-			       u8 status)
+			       s8 status)
 {
 	struct pending_tx_info *pending_tx_info;
 	pending_ring_idx_t index;
@@ -1375,8 +1465,8 @@
 
 	spin_lock_irqsave(&queue->response_lock, flags);
 
-	make_tx_response(queue, &pending_tx_info->req,
-			 pending_tx_info->extra_count, status);
+	_make_tx_response(queue, &pending_tx_info->req,
+			  pending_tx_info->extra_count, status);
 
 	/* Release the pending index before pusing the Tx response so
 	 * its available before a new Tx request is pushed by the
@@ -1390,35 +1480,22 @@
 	spin_unlock_irqrestore(&queue->response_lock, flags);
 }
 
-
 static void make_tx_response(struct xenvif_queue *queue,
-			     struct xen_netif_tx_request *txp,
+			     const struct xen_netif_tx_request *txp,
 			     unsigned int extra_count,
-			     s8       st)
+			     s8 status)
 {
-	RING_IDX i = queue->tx.rsp_prod_pvt;
-	struct xen_netif_tx_response *resp;
-
-	resp = RING_GET_RESPONSE(&queue->tx, i);
-	resp->id     = txp->id;
-	resp->status = st;
-
-	while (extra_count-- != 0)
-		RING_GET_RESPONSE(&queue->tx, ++i)->status = XEN_NETIF_RSP_NULL;
+	unsigned long flags;
 
-	queue->tx.rsp_prod_pvt = ++i;
-}
+	spin_lock_irqsave(&queue->response_lock, flags);
 
-static void push_tx_responses(struct xenvif_queue *queue)
-{
-	int notify;
+	_make_tx_response(queue, txp, extra_count, status);
+	push_tx_responses(queue);
 
-	RING_PUSH_RESPONSES_AND_CHECK_NOTIFY(&queue->tx, notify);
-	if (notify)
-		notify_remote_via_irq(queue->tx_irq);
+	spin_unlock_irqrestore(&queue->response_lock, flags);
 }
 
-void xenvif_idx_unmap(struct xenvif_queue *queue, u16 pending_idx)
+static void xenvif_idx_unmap(struct xenvif_queue *queue, u16 pending_idx)
 {
 	int ret;
 	struct gnttab_unmap_grant_ref tx_unmap_op;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netback/rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netback/rx.c
@@ -33,28 +33,36 @@
 #include <xen/xen.h>
 #include <xen/events.h>
 
-static bool xenvif_rx_ring_slots_available(struct xenvif_queue *queue)
+/*
+ * Update the needed ring page slots for the first SKB queued.
+ * Note that any call sequence outside the RX thread calling this function
+ * needs to wake up the RX thread via a call of xenvif_kick_thread()
+ * afterwards in order to avoid a race with putting the thread to sleep.
+ */
+static void xenvif_update_needed_slots(struct xenvif_queue *queue,
+				       const struct sk_buff *skb)
 {
-	RING_IDX prod, cons;
-	struct sk_buff *skb;
-	int needed;
-	unsigned long flags;
+	unsigned int needed = 0;
 
-	spin_lock_irqsave(&queue->rx_queue.lock, flags);
-
-	skb = skb_peek(&queue->rx_queue);
-	if (!skb) {
-		spin_unlock_irqrestore(&queue->rx_queue.lock, flags);
-		return false;
+	if (skb) {
+		needed = DIV_ROUND_UP(skb->len, XEN_PAGE_SIZE);
+		if (skb_is_gso(skb))
+			needed++;
+		if (skb->sw_hash)
+			needed++;
 	}
 
-	needed = DIV_ROUND_UP(skb->len, XEN_PAGE_SIZE);
-	if (skb_is_gso(skb))
-		needed++;
-	if (skb->sw_hash)
-		needed++;
+	WRITE_ONCE(queue->rx_slots_needed, needed);
+}
 
-	spin_unlock_irqrestore(&queue->rx_queue.lock, flags);
+static bool xenvif_rx_ring_slots_available(struct xenvif_queue *queue)
+{
+	RING_IDX prod, cons;
+	unsigned int needed;
+
+	needed = READ_ONCE(queue->rx_slots_needed);
+	if (!needed)
+		return false;
 
 	do {
 		prod = queue->rx.sring->req_prod;
@@ -74,22 +82,30 @@
 	return false;
 }
 
-void xenvif_rx_queue_tail(struct xenvif_queue *queue, struct sk_buff *skb)
+bool xenvif_rx_queue_tail(struct xenvif_queue *queue, struct sk_buff *skb)
 {
 	unsigned long flags;
+	bool ret = true;
 
 	spin_lock_irqsave(&queue->rx_queue.lock, flags);
 
-	__skb_queue_tail(&queue->rx_queue, skb);
-
-	queue->rx_queue_len += skb->len;
-	if (queue->rx_queue_len > queue->rx_queue_max) {
+	if (queue->rx_queue_len >= queue->rx_queue_max) {
 		struct net_device *dev = queue->vif->dev;
 
 		netif_tx_stop_queue(netdev_get_tx_queue(dev, queue->id));
+		ret = false;
+	} else {
+		if (skb_queue_empty(&queue->rx_queue))
+			xenvif_update_needed_slots(queue, skb);
+
+		__skb_queue_tail(&queue->rx_queue, skb);
+
+		queue->rx_queue_len += skb->len;
 	}
 
 	spin_unlock_irqrestore(&queue->rx_queue.lock, flags);
+
+	return ret;
 }
 
 static struct sk_buff *xenvif_rx_dequeue(struct xenvif_queue *queue)
@@ -100,6 +116,8 @@
 
 	skb = __skb_dequeue(&queue->rx_queue);
 	if (skb) {
+		xenvif_update_needed_slots(queue, skb_peek(&queue->rx_queue));
+
 		queue->rx_queue_len -= skb->len;
 		if (queue->rx_queue_len < queue->rx_queue_max) {
 			struct netdev_queue *txq;
@@ -134,6 +152,7 @@
 			break;
 		xenvif_rx_dequeue(queue);
 		kfree_skb(skb);
+		queue->vif->dev->stats.rx_dropped++;
 	}
 }
 
@@ -469,7 +488,7 @@
 
 #define RX_BATCH_SIZE 64
 
-void xenvif_rx_action(struct xenvif_queue *queue)
+static void xenvif_rx_action(struct xenvif_queue *queue)
 {
 	struct sk_buff_head completed_skbs;
 	unsigned int work_done = 0;
@@ -478,6 +497,7 @@
 	queue->rx_copy.completed = &completed_skbs;
 
 	while (xenvif_rx_ring_slots_available(queue) &&
+	       !skb_queue_empty(&queue->rx_queue) &&
 	       work_done < RX_BATCH_SIZE) {
 		xenvif_rx_skb(queue);
 		work_done++;
@@ -487,27 +507,31 @@
 	xenvif_rx_copy_flush(queue);
 }
 
-static bool xenvif_rx_queue_stalled(struct xenvif_queue *queue)
+static RING_IDX xenvif_rx_queue_slots(const struct xenvif_queue *queue)
 {
 	RING_IDX prod, cons;
 
 	prod = queue->rx.sring->req_prod;
 	cons = queue->rx.req_cons;
 
+	return prod - cons;
+}
+
+static bool xenvif_rx_queue_stalled(const struct xenvif_queue *queue)
+{
+	unsigned int needed = READ_ONCE(queue->rx_slots_needed);
+
 	return !queue->stalled &&
-		prod - cons < 1 &&
+		xenvif_rx_queue_slots(queue) < needed &&
 		time_after(jiffies,
 			   queue->last_rx_time + queue->vif->stall_timeout);
 }
 
 static bool xenvif_rx_queue_ready(struct xenvif_queue *queue)
 {
-	RING_IDX prod, cons;
-
-	prod = queue->rx.sring->req_prod;
-	cons = queue->rx.req_cons;
+	unsigned int needed = READ_ONCE(queue->rx_slots_needed);
 
-	return queue->stalled && prod - cons >= 1;
+	return queue->stalled && xenvif_rx_queue_slots(queue) >= needed;
 }
 
 bool xenvif_have_rx_work(struct xenvif_queue *queue, bool test_kthread)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netback/xenbus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netback/xenbus.c
@@ -675,7 +675,6 @@
 
 		/* Not interested in this watch anymore. */
 		unregister_hotplug_status_watch(be);
-		xenbus_rm(XBT_NIL, be->dev->nodename, "hotplug-status");
 	}
 	kfree(str);
 }
@@ -824,15 +823,11 @@
 	xenvif_carrier_on(be->vif);
 
 	unregister_hotplug_status_watch(be);
-	if (xenbus_exists(XBT_NIL, dev->nodename, "hotplug-status")) {
-		err = xenbus_watch_pathfmt(dev, &be->hotplug_status_watch,
-					   NULL, hotplug_status_changed,
-					   "%s/%s", dev->nodename,
-					   "hotplug-status");
-		if (err)
-			goto err;
+	err = xenbus_watch_pathfmt(dev, &be->hotplug_status_watch, NULL,
+				   hotplug_status_changed,
+				   "%s/%s", dev->nodename, "hotplug-status");
+	if (!err)
 		be->have_hotplug_status_watch = 1;
-	}
 
 	netif_tx_wake_all_queues(be->vif->dev);
 
@@ -988,6 +983,7 @@
 	struct backend_info *be = dev_get_drvdata(&dev->dev);
 
 	unregister_hotplug_status_watch(be);
+	xenbus_rm(XBT_NIL, dev->nodename, "hotplug-status");
 	if (be->vif) {
 		kobject_uevent(&dev->dev.kobj, KOBJ_OFFLINE);
 		backend_disconnect(be);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/net/xen-netfront.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/net/xen-netfront.c
@@ -66,6 +66,10 @@
 MODULE_PARM_DESC(max_queues,
 		 "Maximum number of queues per virtual interface");
 
+static bool __read_mostly xennet_trusted = true;
+module_param_named(trusted, xennet_trusted, bool, 0644);
+MODULE_PARM_DESC(trusted, "Is the backend trusted");
+
 #define XENNET_TIMEOUT  (5 * HZ)
 
 static const struct ethtool_ops xennet_ethtool_ops;
@@ -148,6 +152,9 @@
 	grant_ref_t gref_rx_head;
 	grant_ref_t grant_rx_ref[NET_RX_RING_SIZE];
 
+	unsigned int rx_rsp_unconsumed;
+	spinlock_t rx_cons_lock;
+
 	struct page_pool *page_pool;
 	struct xdp_rxq_info xdp_rxq;
 };
@@ -172,6 +179,9 @@
 	/* Is device behaving sane? */
 	bool broken;
 
+	/* Should skbs be bounced into a zeroed buffer? */
+	bool bounce;
+
 	atomic_t rx_gso_checksum_fixup;
 };
 
@@ -270,12 +280,14 @@
 	if (unlikely(!skb))
 		return NULL;
 
-	page = page_pool_dev_alloc_pages(queue->page_pool);
+	page = page_pool_alloc_pages(queue->page_pool,
+				     GFP_ATOMIC | __GFP_NOWARN | __GFP_ZERO);
 	if (unlikely(!page)) {
 		kfree_skb(skb);
 		return NULL;
 	}
 	skb_add_rx_frag(skb, 0, page, 0, 0, PAGE_SIZE);
+	skb_mark_for_recycle(skb);
 
 	/* Align ip header to a 16 bytes boundary */
 	skb_reserve(skb, NET_IP_ALIGN);
@@ -376,12 +388,13 @@
 	return 0;
 }
 
-static void xennet_tx_buf_gc(struct netfront_queue *queue)
+static bool xennet_tx_buf_gc(struct netfront_queue *queue)
 {
 	RING_IDX cons, prod;
 	unsigned short id;
 	struct sk_buff *skb;
 	bool more_to_do;
+	bool work_done = false;
 	const struct device *dev = &queue->info->netdev->dev;
 
 	BUG_ON(!netif_carrier_ok(queue->info->netdev));
@@ -398,6 +411,8 @@
 		for (cons = queue->tx.rsp_cons; cons != prod; cons++) {
 			struct xen_netif_tx_response txrsp;
 
+			work_done = true;
+
 			RING_COPY_RESPONSE(&queue->tx, cons, &txrsp);
 			if (txrsp.status == XEN_NETIF_RSP_NULL)
 				continue;
@@ -418,14 +433,12 @@
 			queue->tx_link[id] = TX_LINK_NONE;
 			skb = queue->tx_skbs[id];
 			queue->tx_skbs[id] = NULL;
-			if (unlikely(gnttab_query_foreign_access(
-				queue->grant_tx_ref[id]) != 0)) {
+			if (unlikely(!gnttab_end_foreign_access_ref(
+				queue->grant_tx_ref[id], GNTMAP_readonly))) {
 				dev_alert(dev,
 					  "Grant still in use by backend domain\n");
 				goto err;
 			}
-			gnttab_end_foreign_access_ref(
-				queue->grant_tx_ref[id], GNTMAP_readonly);
 			gnttab_release_grant_reference(
 				&queue->gref_tx_head, queue->grant_tx_ref[id]);
 			queue->grant_tx_ref[id] = GRANT_INVALID_REF;
@@ -441,11 +454,13 @@
 
 	xennet_maybe_wake_tx(queue);
 
-	return;
+	return work_done;
 
  err:
 	queue->info->broken = true;
 	dev_alert(dev, "Disabled for further use\n");
+
+	return work_done;
 }
 
 struct xennet_gnttab_make_txreq {
@@ -661,6 +676,33 @@
 	return nxmit;
 }
 
+struct sk_buff *bounce_skb(const struct sk_buff *skb)
+{
+	unsigned int headerlen = skb_headroom(skb);
+	/* Align size to allocate full pages and avoid contiguous data leaks */
+	unsigned int size = ALIGN(skb_end_offset(skb) + skb->data_len,
+				  XEN_PAGE_SIZE);
+	struct sk_buff *n = alloc_skb(size, GFP_ATOMIC | __GFP_ZERO);
+
+	if (!n)
+		return NULL;
+
+	if (!IS_ALIGNED((uintptr_t)n->head, XEN_PAGE_SIZE)) {
+		WARN_ONCE(1, "misaligned skb allocated\n");
+		kfree_skb(n);
+		return NULL;
+	}
+
+	/* Set the data pointer */
+	skb_reserve(n, headerlen);
+	/* Set the tail pointer and length */
+	skb_put(n, skb->len);
+
+	BUG_ON(skb_copy_bits(skb, -headerlen, n->head, headerlen + skb->len));
+
+	skb_copy_header(n, skb);
+	return n;
+}
 
 #define MAX_XEN_SKB_FRAGS (65536 / XEN_PAGE_SIZE + 1)
 
@@ -714,9 +756,13 @@
 
 	/* The first req should be at least ETH_HLEN size or the packet will be
 	 * dropped by netback.
+	 *
+	 * If the backend is not trusted bounce all data to zeroed pages to
+	 * avoid exposing contiguous data on the granted page not belonging to
+	 * the skb.
 	 */
-	if (unlikely(PAGE_SIZE - offset < ETH_HLEN)) {
-		nskb = skb_copy(skb, GFP_ATOMIC);
+	if (np->bounce || unlikely(PAGE_SIZE - offset < ETH_HLEN)) {
+		nskb = bounce_skb(skb);
 		if (!nskb)
 			goto drop;
 		dev_consume_skb_any(skb);
@@ -823,7 +869,7 @@
 static int xennet_close(struct net_device *dev)
 {
 	struct netfront_info *np = netdev_priv(dev);
-	unsigned int num_queues = dev->real_num_tx_queues;
+	unsigned int num_queues = np->queues ? dev->real_num_tx_queues : 0;
 	unsigned int i;
 	struct netfront_queue *queue;
 	netif_tx_stop_all_queues(np->netdev);
@@ -834,6 +880,41 @@
 	return 0;
 }
 
+static void xennet_destroy_queues(struct netfront_info *info)
+{
+	unsigned int i;
+
+	if (!info->queues)
+		return;
+
+	for (i = 0; i < info->netdev->real_num_tx_queues; i++) {
+		struct netfront_queue *queue = &info->queues[i];
+
+		if (netif_running(info->netdev))
+			napi_disable(&queue->napi);
+		netif_napi_del(&queue->napi);
+	}
+
+	kfree(info->queues);
+	info->queues = NULL;
+}
+
+static void xennet_uninit(struct net_device *dev)
+{
+	struct netfront_info *np = netdev_priv(dev);
+	xennet_destroy_queues(np);
+}
+
+static void xennet_set_rx_rsp_cons(struct netfront_queue *queue, RING_IDX val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&queue->rx_cons_lock, flags);
+	queue->rx.rsp_cons = val;
+	queue->rx_rsp_unconsumed = RING_HAS_UNCONSUMED_RESPONSES(&queue->rx);
+	spin_unlock_irqrestore(&queue->rx_cons_lock, flags);
+}
+
 static void xennet_move_rx_slot(struct netfront_queue *queue, struct sk_buff *skb,
 				grant_ref_t ref)
 {
@@ -885,7 +966,7 @@
 		xennet_move_rx_slot(queue, skb, ref);
 	} while (extra.flags & XEN_NETIF_EXTRA_FLAG_MORE);
 
-	queue->rx.rsp_cons = cons;
+	xennet_set_rx_rsp_cons(queue, cons);
 	return err;
 }
 
@@ -950,7 +1031,6 @@
 	struct device *dev = &queue->info->netdev->dev;
 	struct bpf_prog *xdp_prog;
 	struct xdp_buff xdp;
-	unsigned long ret;
 	int slots = 1;
 	int err = 0;
 	u32 verdict;
@@ -992,8 +1072,13 @@
 			goto next;
 		}
 
-		ret = gnttab_end_foreign_access_ref(ref, 0);
-		BUG_ON(!ret);
+		if (!gnttab_end_foreign_access_ref(ref, 0)) {
+			dev_alert(dev,
+				  "Grant still in use by backend domain\n");
+			queue->info->broken = true;
+			dev_alert(dev, "Disabled for further use\n");
+			return -EINVAL;
+		}
 
 		gnttab_release_grant_reference(&queue->gref_rx_head, ref);
 
@@ -1013,8 +1098,10 @@
 			}
 		}
 		rcu_read_unlock();
-next:
+
 		__skb_queue_tail(list, skb);
+
+next:
 		if (!(rx->flags & XEN_NETRXF_more_data))
 			break;
 
@@ -1039,7 +1126,7 @@
 	}
 
 	if (unlikely(err))
-		queue->rx.rsp_cons = cons + slots;
+		xennet_set_rx_rsp_cons(queue, cons + slots);
 
 	return err;
 }
@@ -1093,7 +1180,8 @@
 			__pskb_pull_tail(skb, pull_to - skb_headlen(skb));
 		}
 		if (unlikely(skb_shinfo(skb)->nr_frags >= MAX_SKB_FRAGS)) {
-			queue->rx.rsp_cons = ++cons + skb_queue_len(list);
+			xennet_set_rx_rsp_cons(queue,
+					       ++cons + skb_queue_len(list));
 			kfree_skb(nskb);
 			return -ENOENT;
 		}
@@ -1106,7 +1194,7 @@
 		kfree_skb(nskb);
 	}
 
-	queue->rx.rsp_cons = cons;
+	xennet_set_rx_rsp_cons(queue, cons);
 
 	return 0;
 }
@@ -1213,6 +1301,10 @@
 					   &need_xdp_flush);
 
 		if (unlikely(err)) {
+			if (queue->info->broken) {
+				spin_unlock(&queue->rx_lock);
+				return 0;
+			}
 err:
 			while ((skb = __skb_dequeue(&tmpq)))
 				__skb_queue_tail(&errq, skb);
@@ -1229,7 +1321,9 @@
 
 			if (unlikely(xennet_set_skb_gso(skb, gso))) {
 				__skb_queue_head(&tmpq, skb);
-				queue->rx.rsp_cons += skb_queue_len(&tmpq);
+				xennet_set_rx_rsp_cons(queue,
+						       queue->rx.rsp_cons +
+						       skb_queue_len(&tmpq));
 				goto err;
 			}
 		}
@@ -1253,7 +1347,8 @@
 
 		__skb_queue_tail(&rxq, skb);
 
-		i = ++queue->rx.rsp_cons;
+		i = queue->rx.rsp_cons + 1;
+		xennet_set_rx_rsp_cons(queue, i);
 		work_done++;
 	}
 	if (need_xdp_flush)
@@ -1417,40 +1512,79 @@
 	return 0;
 }
 
-static irqreturn_t xennet_tx_interrupt(int irq, void *dev_id)
+static bool xennet_handle_tx(struct netfront_queue *queue, unsigned int *eoi)
 {
-	struct netfront_queue *queue = dev_id;
 	unsigned long flags;
 
-	if (queue->info->broken)
-		return IRQ_HANDLED;
+	if (unlikely(queue->info->broken))
+		return false;
 
 	spin_lock_irqsave(&queue->tx_lock, flags);
-	xennet_tx_buf_gc(queue);
+	if (xennet_tx_buf_gc(queue))
+		*eoi = 0;
 	spin_unlock_irqrestore(&queue->tx_lock, flags);
 
+	return true;
+}
+
+static irqreturn_t xennet_tx_interrupt(int irq, void *dev_id)
+{
+	unsigned int eoiflag = XEN_EOI_FLAG_SPURIOUS;
+
+	if (likely(xennet_handle_tx(dev_id, &eoiflag)))
+		xen_irq_lateeoi(irq, eoiflag);
+
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t xennet_rx_interrupt(int irq, void *dev_id)
+static bool xennet_handle_rx(struct netfront_queue *queue, unsigned int *eoi)
 {
-	struct netfront_queue *queue = dev_id;
-	struct net_device *dev = queue->info->netdev;
+	unsigned int work_queued;
+	unsigned long flags;
 
-	if (queue->info->broken)
-		return IRQ_HANDLED;
+	if (unlikely(queue->info->broken))
+		return false;
 
-	if (likely(netif_carrier_ok(dev) &&
-		   RING_HAS_UNCONSUMED_RESPONSES(&queue->rx)))
+	spin_lock_irqsave(&queue->rx_cons_lock, flags);
+	work_queued = RING_HAS_UNCONSUMED_RESPONSES(&queue->rx);
+	if (work_queued > queue->rx_rsp_unconsumed) {
+		queue->rx_rsp_unconsumed = work_queued;
+		*eoi = 0;
+	} else if (unlikely(work_queued < queue->rx_rsp_unconsumed)) {
+		const struct device *dev = &queue->info->netdev->dev;
+
+		spin_unlock_irqrestore(&queue->rx_cons_lock, flags);
+		dev_alert(dev, "RX producer index going backwards\n");
+		dev_alert(dev, "Disabled for further use\n");
+		queue->info->broken = true;
+		return false;
+	}
+	spin_unlock_irqrestore(&queue->rx_cons_lock, flags);
+
+	if (likely(netif_carrier_ok(queue->info->netdev) && work_queued))
 		napi_schedule(&queue->napi);
 
+	return true;
+}
+
+static irqreturn_t xennet_rx_interrupt(int irq, void *dev_id)
+{
+	unsigned int eoiflag = XEN_EOI_FLAG_SPURIOUS;
+
+	if (likely(xennet_handle_rx(dev_id, &eoiflag)))
+		xen_irq_lateeoi(irq, eoiflag);
+
 	return IRQ_HANDLED;
 }
 
 static irqreturn_t xennet_interrupt(int irq, void *dev_id)
 {
-	xennet_tx_interrupt(irq, dev_id);
-	xennet_rx_interrupt(irq, dev_id);
+	unsigned int eoiflag = XEN_EOI_FLAG_SPURIOUS;
+
+	if (xennet_handle_tx(dev_id, &eoiflag) &&
+	    xennet_handle_rx(dev_id, &eoiflag))
+		xen_irq_lateeoi(irq, eoiflag);
+
 	return IRQ_HANDLED;
 }
 
@@ -1550,6 +1684,7 @@
 }
 
 static const struct net_device_ops xennet_netdev_ops = {
+	.ndo_uninit          = xennet_uninit,
 	.ndo_open            = xennet_open,
 	.ndo_stop            = xennet_close,
 	.ndo_start_xmit      = xennet_start_xmit,
@@ -1735,6 +1870,12 @@
 	netif_tx_unlock_bh(info->netdev);
 
 	xennet_disconnect_backend(info);
+
+	rtnl_lock();
+	if (info->queues)
+		xennet_destroy_queues(info);
+	rtnl_unlock();
+
 	return 0;
 }
 
@@ -1768,9 +1909,10 @@
 	if (err < 0)
 		goto fail;
 
-	err = bind_evtchn_to_irqhandler(queue->tx_evtchn,
-					xennet_interrupt,
-					0, queue->info->netdev->name, queue);
+	err = bind_evtchn_to_irqhandler_lateeoi(queue->tx_evtchn,
+						xennet_interrupt, 0,
+						queue->info->netdev->name,
+						queue);
 	if (err < 0)
 		goto bind_fail;
 	queue->rx_evtchn = queue->tx_evtchn;
@@ -1798,18 +1940,18 @@
 
 	snprintf(queue->tx_irq_name, sizeof(queue->tx_irq_name),
 		 "%s-tx", queue->name);
-	err = bind_evtchn_to_irqhandler(queue->tx_evtchn,
-					xennet_tx_interrupt,
-					0, queue->tx_irq_name, queue);
+	err = bind_evtchn_to_irqhandler_lateeoi(queue->tx_evtchn,
+						xennet_tx_interrupt, 0,
+						queue->tx_irq_name, queue);
 	if (err < 0)
 		goto bind_tx_fail;
 	queue->tx_irq = err;
 
 	snprintf(queue->rx_irq_name, sizeof(queue->rx_irq_name),
 		 "%s-rx", queue->name);
-	err = bind_evtchn_to_irqhandler(queue->rx_evtchn,
-					xennet_rx_interrupt,
-					0, queue->rx_irq_name, queue);
+	err = bind_evtchn_to_irqhandler_lateeoi(queue->rx_evtchn,
+						xennet_rx_interrupt, 0,
+						queue->rx_irq_name, queue);
 	if (err < 0)
 		goto bind_rx_fail;
 	queue->rx_irq = err;
@@ -1833,7 +1975,7 @@
 			struct netfront_queue *queue, unsigned int feature_split_evtchn)
 {
 	struct xen_netif_tx_sring *txs;
-	struct xen_netif_rx_sring *rxs;
+	struct xen_netif_rx_sring *rxs = NULL;
 	grant_ref_t gref;
 	int err;
 
@@ -1853,21 +1995,21 @@
 
 	err = xenbus_grant_ring(dev, txs, 1, &gref);
 	if (err < 0)
-		goto grant_tx_ring_fail;
+		goto fail;
 	queue->tx_ring_ref = gref;
 
 	rxs = (struct xen_netif_rx_sring *)get_zeroed_page(GFP_NOIO | __GFP_HIGH);
 	if (!rxs) {
 		err = -ENOMEM;
 		xenbus_dev_fatal(dev, err, "allocating rx ring page");
-		goto alloc_rx_ring_fail;
+		goto fail;
 	}
 	SHARED_RING_INIT(rxs);
 	FRONT_RING_INIT(&queue->rx, rxs, XEN_PAGE_SIZE);
 
 	err = xenbus_grant_ring(dev, rxs, 1, &gref);
 	if (err < 0)
-		goto grant_rx_ring_fail;
+		goto fail;
 	queue->rx_ring_ref = gref;
 
 	if (feature_split_evtchn)
@@ -1880,22 +2022,28 @@
 		err = setup_netfront_single(queue);
 
 	if (err)
-		goto alloc_evtchn_fail;
+		goto fail;
 
 	return 0;
 
 	/* If we fail to setup netfront, it is safe to just revoke access to
 	 * granted pages because backend is not accessing it at this point.
 	 */
-alloc_evtchn_fail:
-	gnttab_end_foreign_access_ref(queue->rx_ring_ref, 0);
-grant_rx_ring_fail:
-	free_page((unsigned long)rxs);
-alloc_rx_ring_fail:
-	gnttab_end_foreign_access_ref(queue->tx_ring_ref, 0);
-grant_tx_ring_fail:
-	free_page((unsigned long)txs);
-fail:
+ fail:
+	if (queue->rx_ring_ref != GRANT_INVALID_REF) {
+		gnttab_end_foreign_access(queue->rx_ring_ref, 0,
+					  (unsigned long)rxs);
+		queue->rx_ring_ref = GRANT_INVALID_REF;
+	} else {
+		free_page((unsigned long)rxs);
+	}
+	if (queue->tx_ring_ref != GRANT_INVALID_REF) {
+		gnttab_end_foreign_access(queue->tx_ring_ref, 0,
+					  (unsigned long)txs);
+		queue->tx_ring_ref = GRANT_INVALID_REF;
+	} else {
+		free_page((unsigned long)txs);
+	}
 	return err;
 }
 
@@ -1911,6 +2059,7 @@
 
 	spin_lock_init(&queue->tx_lock);
 	spin_lock_init(&queue->rx_lock);
+	spin_lock_init(&queue->rx_cons_lock);
 
 	timer_setup(&queue->rx_refill_timer, rx_refill_timeout, 0);
 
@@ -2040,22 +2189,6 @@
 	return err;
 }
 
-static void xennet_destroy_queues(struct netfront_info *info)
-{
-	unsigned int i;
-
-	for (i = 0; i < info->netdev->real_num_tx_queues; i++) {
-		struct netfront_queue *queue = &info->queues[i];
-
-		if (netif_running(info->netdev))
-			napi_disable(&queue->napi);
-		netif_napi_del(&queue->napi);
-	}
-
-	kfree(info->queues);
-	info->queues = NULL;
-}
-
 
 
 static int xennet_create_page_pool(struct netfront_queue *queue)
@@ -2164,6 +2297,10 @@
 
 	info->netdev->irq = 0;
 
+	/* Check if backend is trusted. */
+	info->bounce = !xennet_trusted ||
+		       !xenbus_read_unsigned(dev->nodename, "trusted", 1);
+
 	/* Check if backend supports multiple queues */
 	max_queues = xenbus_read_unsigned(info->xbdev->otherend,
 					  "multi-queue-max-queues", 1);
@@ -2330,6 +2467,9 @@
 		return err;
 	if (np->netback_has_xdp_headroom)
 		pr_info("backend supports XDP headroom\n");
+	if (np->bounce)
+		dev_info(&np->xbdev->dev,
+			 "bouncing transmitted data to zeroed pages\n");
 
 	/* talk_to_netback() sets the correct number of queues */
 	num_queues = dev->real_num_tx_queues;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/fdp/fdp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/fdp/fdp.c
@@ -249,11 +249,19 @@
 static int fdp_nci_send(struct nci_dev *ndev, struct sk_buff *skb)
 {
 	struct fdp_nci_info *info = nci_get_drvdata(ndev);
+	int ret;
 
 	if (atomic_dec_and_test(&info->data_pkt_counter))
 		info->data_pkt_counter_cb(ndev);
 
-	return info->phy_ops->write(info->phy, skb);
+	ret = info->phy_ops->write(info->phy, skb);
+	if (ret < 0) {
+		kfree_skb(skb);
+		return ret;
+	}
+
+	consume_skb(skb);
+	return 0;
 }
 
 static int fdp_nci_request_firmware(struct nci_dev *ndev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/fdp/i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/fdp/i2c.c
@@ -249,6 +249,9 @@
 					   len, sizeof(**fw_vsc_cfg),
 					   GFP_KERNEL);
 
+		if (!*fw_vsc_cfg)
+			goto alloc_err;
+
 		r = device_property_read_u8_array(dev, FDP_DP_FW_VSC_CFG_NAME,
 						  *fw_vsc_cfg, len);
 
@@ -262,6 +265,7 @@
 		*fw_vsc_cfg = NULL;
 	}
 
+alloc_err:
 	dev_dbg(dev, "Clock type: %d, clock frequency: %d, VSC: %s",
 		*clock_type, *clock_freq, *fw_vsc_cfg != NULL ? "yes" : "no");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nfcmrvl/i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nfcmrvl/i2c.c
@@ -132,10 +132,15 @@
 			ret = -EREMOTEIO;
 		} else
 			ret = 0;
+	}
+
+	if (ret) {
 		kfree_skb(skb);
+		return ret;
 	}
 
-	return ret;
+	consume_skb(skb);
+	return 0;
 }
 
 static void nfcmrvl_i2c_nci_update_config(struct nfcmrvl_private *priv,
@@ -167,9 +172,9 @@
 		pdata->irq_polarity = IRQF_TRIGGER_RISING;
 
 	ret = irq_of_parse_and_map(node, 0);
-	if (ret < 0) {
-		pr_err("Unable to get irq, error: %d\n", ret);
-		return ret;
+	if (!ret) {
+		pr_err("Unable to get irq\n");
+		return -EINVAL;
 	}
 	pdata->irq = ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nfcmrvl/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nfcmrvl/main.c
@@ -183,6 +183,7 @@
 {
 	struct nci_dev *ndev = priv->ndev;
 
+	nci_unregister_device(ndev);
 	if (priv->ndev->nfc_dev->fw_download_in_progress)
 		nfcmrvl_fw_dnld_abort(priv);
 
@@ -191,7 +192,6 @@
 	if (gpio_is_valid(priv->config.reset_n_io))
 		gpio_free(priv->config.reset_n_io);
 
-	nci_unregister_device(ndev);
 	nci_free_device(ndev);
 	kfree(priv);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nfcmrvl/spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nfcmrvl/spi.c
@@ -115,9 +115,9 @@
 	}
 
 	ret = irq_of_parse_and_map(node, 0);
-	if (ret < 0) {
-		pr_err("Unable to get irq, error: %d\n", ret);
-		return ret;
+	if (!ret) {
+		pr_err("Unable to get irq\n");
+		return -EINVAL;
 	}
 	pdata->irq = ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nfcmrvl/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nfcmrvl/usb.c
@@ -388,13 +388,25 @@
 	int err;
 
 	while ((urb = usb_get_from_anchor(&drv_data->deferred))) {
+		usb_anchor_urb(urb, &drv_data->tx_anchor);
+
 		err = usb_submit_urb(urb, GFP_ATOMIC);
-		if (err)
+		if (err) {
+			kfree(urb->setup_packet);
+			usb_unanchor_urb(urb);
+			usb_free_urb(urb);
 			break;
+		}
 
 		drv_data->tx_in_flight++;
+		usb_free_urb(urb);
+	}
+
+	/* Cleanup the rest deferred urbs. */
+	while ((urb = usb_get_from_anchor(&drv_data->deferred))) {
+		kfree(urb->setup_packet);
+		usb_free_urb(urb);
 	}
-	usb_scuttle_anchored_urbs(&drv_data->deferred);
 }
 
 static int nfcmrvl_resume(struct usb_interface *intf)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nfcsim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nfcsim.c
@@ -336,10 +336,6 @@
 static void nfcsim_debugfs_init(void)
 {
 	nfcsim_debugfs_root = debugfs_create_dir("nfcsim", NULL);
-
-	if (!nfcsim_debugfs_root)
-		pr_err("Could not create debugfs entry\n");
-
 }
 
 static void nfcsim_debugfs_remove(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nxp-nci/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nxp-nci/core.c
@@ -77,10 +77,13 @@
 		return -EINVAL;
 
 	r = info->phy_ops->write(info->phy_id, skb);
-	if (r < 0)
+	if (r < 0) {
 		kfree_skb(skb);
+		return r;
+	}
 
-	return r;
+	consume_skb(skb);
+	return 0;
 }
 
 static const struct nci_ops nxp_nci_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/nxp-nci/i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/nxp-nci/i2c.c
@@ -122,7 +122,9 @@
 	skb_put_data(*skb, &header, NXP_NCI_FW_HDR_LEN);
 
 	r = i2c_master_recv(client, skb_put(*skb, frame_len), frame_len);
-	if (r != frame_len) {
+	if (r < 0) {
+		goto fw_read_exit_free_skb;
+	} else if (r != frame_len) {
 		nfc_err(&client->dev,
 			"Invalid frame length: %u (expected %zu)\n",
 			r, frame_len);
@@ -162,8 +164,13 @@
 
 	skb_put_data(*skb, (void *)&header, NCI_CTRL_HDR_SIZE);
 
+	if (!header.plen)
+		return 0;
+
 	r = i2c_master_recv(client, skb_put(*skb, header.plen), header.plen);
-	if (r != header.plen) {
+	if (r < 0) {
+		goto nci_read_exit_free_skb;
+	} else if (r != header.plen) {
 		nfc_err(&client->dev,
 			"Invalid frame payload length: %u (expected %u)\n",
 			r, header.plen);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/pn533/pn533.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/pn533/pn533.c
@@ -1297,6 +1297,8 @@
 	if (IS_ERR(resp))
 		return PTR_ERR(resp);
 
+	memset(&nfc_target, 0, sizeof(struct nfc_target));
+
 	rsp = (struct pn533_cmd_jump_dep_response *)resp->data;
 
 	rc = rsp->status & PN533_CMD_RET_MASK;
@@ -1723,6 +1725,11 @@
 	}
 
 	pn533_poll_create_mod_list(dev, im_protocols, tm_protocols);
+	if (!dev->poll_mod_count) {
+		nfc_err(dev->dev,
+			"Poll mod list is empty\n");
+		return -EINVAL;
+	}
 
 	/* Do not always start polling from the same modulation */
 	get_random_bytes(&rand_mod, sizeof(rand_mod));
@@ -1928,6 +1935,8 @@
 
 		dev_dbg(dev->dev, "Creating new target\n");
 
+		memset(&nfc_target, 0, sizeof(struct nfc_target));
+
 		nfc_target.supported_protocols = NFC_PROTO_NFC_DEP_MASK;
 		nfc_target.nfcid1_len = 10;
 		memcpy(nfc_target.nfcid1, rsp->nfcid3t, nfc_target.nfcid1_len);
@@ -2218,7 +2227,7 @@
 		frag = pn533_alloc_skb(dev, frag_size);
 		if (!frag) {
 			skb_queue_purge(&dev->fragment_skb);
-			break;
+			return -ENOMEM;
 		}
 
 		if (!dev->tgt_mode) {
@@ -2287,7 +2296,7 @@
 		/* jumbo frame ? */
 		if (skb->len > PN533_CMD_DATAEXCH_DATA_MAXLEN) {
 			rc = pn533_fill_fragment_skbs(dev, skb);
-			if (rc <= 0)
+			if (rc < 0)
 				goto error;
 
 			skb = skb_dequeue(&dev->fragment_skb);
@@ -2355,7 +2364,7 @@
 	/* let's split in multiple chunks if size's too big */
 	if (skb->len > PN533_CMD_DATAEXCH_DATA_MAXLEN) {
 		rc = pn533_fill_fragment_skbs(dev, skb);
-		if (rc <= 0)
+		if (rc < 0)
 			goto error;
 
 		/* get the first skb */
@@ -2789,13 +2798,14 @@
 {
 	struct pn533_cmd *cmd, *n;
 
+	/* delete the timer before cleanup the worker */
+	del_timer_sync(&priv->listen_timer);
+
 	flush_delayed_work(&priv->poll_work);
 	destroy_workqueue(priv->wq);
 
 	skb_queue_purge(&priv->resp_q);
 
-	del_timer(&priv->listen_timer);
-
 	list_for_each_entry_safe(cmd, n, &priv->cmd_queue, queue) {
 		list_del(&cmd->queue);
 		kfree(cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/pn533/uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/pn533/uart.c
@@ -310,6 +310,7 @@
 	pn53x_unregister_nfc(pn532->priv);
 	serdev_device_close(serdev);
 	pn53x_common_clean(pn532->priv);
+	del_timer_sync(&pn532->cmd_timeout);
 	kfree_skb(pn532->recv_skb);
 	kfree(pn532);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/pn533/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/pn533/usb.c
@@ -153,10 +153,17 @@
 	return usb_submit_urb(phy->ack_urb, flags);
 }
 
+struct pn533_out_arg {
+	struct pn533_usb_phy *phy;
+	struct completion done;
+};
+
 static int pn533_usb_send_frame(struct pn533 *dev,
 				struct sk_buff *out)
 {
 	struct pn533_usb_phy *phy = dev->phy;
+	struct pn533_out_arg arg;
+	void *cntx;
 	int rc;
 
 	if (phy->priv == NULL)
@@ -168,10 +175,18 @@
 	print_hex_dump_debug("PN533 TX: ", DUMP_PREFIX_NONE, 16, 1,
 			     out->data, out->len, false);
 
+	arg.phy = phy;
+	init_completion(&arg.done);
+	cntx = phy->out_urb->context;
+	phy->out_urb->context = &arg;
+
 	rc = usb_submit_urb(phy->out_urb, GFP_KERNEL);
 	if (rc)
 		return rc;
 
+	wait_for_completion(&arg.done);
+	phy->out_urb->context = cntx;
+
 	if (dev->protocol_type == PN533_PROTO_REQ_RESP) {
 		/* request for response for sent packet directly */
 		rc = pn533_submit_urb_for_response(phy, GFP_KERNEL);
@@ -408,7 +423,31 @@
 	return arg.rc;
 }
 
-static void pn533_send_complete(struct urb *urb)
+static void pn533_out_complete(struct urb *urb)
+{
+	struct pn533_out_arg *arg = urb->context;
+	struct pn533_usb_phy *phy = arg->phy;
+
+	switch (urb->status) {
+	case 0:
+		break; /* success */
+	case -ECONNRESET:
+	case -ENOENT:
+		dev_dbg(&phy->udev->dev,
+			"The urb has been stopped (status %d)\n",
+			urb->status);
+		break;
+	case -ESHUTDOWN:
+	default:
+		nfc_err(&phy->udev->dev,
+			"Urb failure (status %d)\n",
+			urb->status);
+	}
+
+	complete(&arg->done);
+}
+
+static void pn533_ack_complete(struct urb *urb)
 {
 	struct pn533_usb_phy *phy = urb->context;
 
@@ -496,10 +535,10 @@
 
 	usb_fill_bulk_urb(phy->out_urb, phy->udev,
 			  usb_sndbulkpipe(phy->udev, out_endpoint),
-			  NULL, 0, pn533_send_complete, phy);
+			  NULL, 0, pn533_out_complete, phy);
 	usb_fill_bulk_urb(phy->ack_urb, phy->udev,
 			  usb_sndbulkpipe(phy->udev, out_endpoint),
-			  NULL, 0, pn533_send_complete, phy);
+			  NULL, 0, pn533_ack_complete, phy);
 
 	switch (id->driver_info) {
 	case PN533_DEVICE_STD:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/port100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/port100.c
@@ -1612,7 +1612,9 @@
 	nfc_digital_free_device(dev->nfc_digital_dev);
 
 error:
+	usb_kill_urb(dev->in_urb);
 	usb_free_urb(dev->in_urb);
+	usb_kill_urb(dev->out_urb);
 	usb_free_urb(dev->out_urb);
 	usb_put_dev(dev->udev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/s3fwrn5/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/s3fwrn5/core.c
@@ -110,11 +110,15 @@
 	}
 
 	ret = s3fwrn5_write(info, skb);
-	if (ret < 0)
+	if (ret < 0) {
 		kfree_skb(skb);
+		mutex_unlock(&info->mutex);
+		return ret;
+	}
 
+	consume_skb(skb);
 	mutex_unlock(&info->mutex);
-	return ret;
+	return 0;
 }
 
 static int s3fwrn5_nci_post_setup(struct nci_dev *ndev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/st-nci/ndlc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/st-nci/ndlc.c
@@ -286,13 +286,15 @@
 
 void ndlc_remove(struct llt_ndlc *ndlc)
 {
-	st_nci_remove(ndlc->ndev);
-
 	/* cancel timers */
 	del_timer_sync(&ndlc->t1_timer);
 	del_timer_sync(&ndlc->t2_timer);
 	ndlc->t2_active = false;
 	ndlc->t1_active = false;
+	/* cancel work */
+	cancel_work_sync(&ndlc->sm_work);
+
+	st_nci_remove(ndlc->ndev);
 
 	skb_queue_purge(&ndlc->rcv_q);
 	skb_queue_purge(&ndlc->send_q);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/st-nci/se.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/st-nci/se.c
@@ -312,6 +312,8 @@
 	int r = 0;
 	struct device *dev = &ndev->nfc_dev->dev;
 	struct nfc_evt_transaction *transaction;
+	u32 aid_len;
+	u8 params_len;
 
 	pr_debug("connectivity gate event: %x\n", event);
 
@@ -325,26 +327,47 @@
 		 * Description  Tag     Length
 		 * AID          81      5 to 16
 		 * PARAMETERS   82      0 to 255
+		 *
+		 * The key differences are aid storage length is variably sized
+		 * in the packet, but fixed in nfc_evt_transaction, and that
+		 * the aid_len is u8 in the packet, but u32 in the structure,
+		 * and the tags in the packet are not included in
+		 * nfc_evt_transaction.
+		 *
+		 * size(b):  1          1       5-16 1             1           0-255
+		 * offset:   0          1       2    aid_len + 2   aid_len + 3 aid_len + 4
+		 * mem name: aid_tag(M) aid_len aid  params_tag(M) params_len  params
+		 * example:  0x81       5-16    X    0x82          0-255       X
 		 */
-		if (skb->len < NFC_MIN_AID_LENGTH + 2 &&
-		    skb->data[0] != NFC_EVT_TRANSACTION_AID_TAG)
+		if (skb->len < 2 || skb->data[0] != NFC_EVT_TRANSACTION_AID_TAG)
 			return -EPROTO;
 
-		transaction = devm_kzalloc(dev, skb->len - 2, GFP_KERNEL);
-		if (!transaction)
-			return -ENOMEM;
+		aid_len = skb->data[1];
 
-		transaction->aid_len = skb->data[1];
-		memcpy(transaction->aid, &skb->data[2], transaction->aid_len);
+		if (skb->len < aid_len + 4 ||
+		    aid_len > sizeof(transaction->aid))
+			return -EPROTO;
 
-		/* Check next byte is PARAMETERS tag (82) */
-		if (skb->data[transaction->aid_len + 2] !=
-		    NFC_EVT_TRANSACTION_PARAMS_TAG)
+		params_len = skb->data[aid_len + 3];
+
+		/* Verify PARAMETERS tag is (82), and final check that there is
+		 * enough space in the packet to read everything.
+		 */
+		if (skb->data[aid_len + 2] != NFC_EVT_TRANSACTION_PARAMS_TAG ||
+		    skb->len < aid_len + 4 + params_len)
 			return -EPROTO;
 
-		transaction->params_len = skb->data[transaction->aid_len + 3];
-		memcpy(transaction->params, skb->data +
-		       transaction->aid_len + 4, transaction->params_len);
+		transaction = devm_kzalloc(dev, sizeof(*transaction) +
+					   params_len, GFP_KERNEL);
+		if (!transaction)
+			return -ENOMEM;
+
+		transaction->aid_len = aid_len;
+		transaction->params_len = params_len;
+
+		memcpy(transaction->aid, &skb->data[2], aid_len);
+		memcpy(transaction->params, &skb->data[aid_len + 4],
+		       params_len);
 
 		r = nfc_se_transaction(ndev->nfc_dev, host, transaction);
 		break;
@@ -651,6 +674,12 @@
 					ST_NCI_EVT_TRANSMIT_DATA, apdu,
 					apdu_length);
 	default:
+		/* Need to free cb_context here as at the moment we can't
+		 * clearly indicate to the caller if the callback function
+		 * would be called (and free it) or not. In both cases a
+		 * negative value may be returned to the caller.
+		 */
+		kfree(cb_context);
 		return -ENODEV;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/st21nfca/i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/st21nfca/i2c.c
@@ -528,7 +528,8 @@
 	phy->gpiod_ena = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
 	if (IS_ERR(phy->gpiod_ena)) {
 		nfc_err(dev, "Unable to get ENABLE GPIO\n");
-		return PTR_ERR(phy->gpiod_ena);
+		r = PTR_ERR(phy->gpiod_ena);
+		goto out_free;
 	}
 
 	phy->se_status.is_ese_present =
@@ -539,7 +540,7 @@
 	r = st21nfca_hci_platform_init(phy);
 	if (r < 0) {
 		nfc_err(&client->dev, "Unable to reboot st21nfca\n");
-		return r;
+		goto out_free;
 	}
 
 	r = devm_request_threaded_irq(&client->dev, client->irq, NULL,
@@ -548,15 +549,23 @@
 				ST21NFCA_HCI_DRIVER_NAME, phy);
 	if (r < 0) {
 		nfc_err(&client->dev, "Unable to register IRQ handler\n");
-		return r;
+		goto out_free;
 	}
 
-	return st21nfca_hci_probe(phy, &i2c_phy_ops, LLC_SHDLC_NAME,
-					ST21NFCA_FRAME_HEADROOM,
-					ST21NFCA_FRAME_TAILROOM,
-					ST21NFCA_HCI_LLC_MAX_PAYLOAD,
-					&phy->hdev,
-					&phy->se_status);
+	r = st21nfca_hci_probe(phy, &i2c_phy_ops, LLC_SHDLC_NAME,
+			       ST21NFCA_FRAME_HEADROOM,
+			       ST21NFCA_FRAME_TAILROOM,
+			       ST21NFCA_HCI_LLC_MAX_PAYLOAD,
+			       &phy->hdev,
+			       &phy->se_status);
+	if (r)
+		goto out_free;
+
+	return 0;
+
+out_free:
+	kfree_skb(phy->pending_skb);
+	return r;
 }
 
 static int st21nfca_hci_i2c_remove(struct i2c_client *client)
@@ -567,6 +576,8 @@
 
 	if (phy->powered)
 		st21nfca_hci_i2c_disable(phy);
+	if (phy->pending_skb)
+		kfree_skb(phy->pending_skb);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/st21nfca/se.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/st21nfca/se.c
@@ -236,12 +236,18 @@
 					ST21NFCA_EVT_TRANSMIT_DATA,
 					apdu, apdu_length);
 	default:
+		/* Need to free cb_context here as at the moment we can't
+		 * clearly indicate to the caller if the callback function
+		 * would be called (and free it) or not. In both cases a
+		 * negative value may be returned to the caller.
+		 */
+		kfree(cb_context);
 		return -ENODEV;
 	}
 }
 EXPORT_SYMBOL(st21nfca_hci_se_io);
 
-static void st21nfca_se_wt_timeout(struct timer_list *t)
+static void st21nfca_se_wt_work(struct work_struct *work)
 {
 	/*
 	 * No answer from the secure element
@@ -254,8 +260,9 @@
 	 */
 	/* hardware reset managed through VCC_UICC_OUT power supply */
 	u8 param = 0x01;
-	struct st21nfca_hci_info *info = from_timer(info, t,
-						    se_info.bwi_timer);
+	struct st21nfca_hci_info *info = container_of(work,
+						struct st21nfca_hci_info,
+						se_info.timeout_work);
 
 	pr_debug("\n");
 
@@ -273,6 +280,13 @@
 	info->se_info.cb(info->se_info.cb_context, NULL, 0, -ETIME);
 }
 
+static void st21nfca_se_wt_timeout(struct timer_list *t)
+{
+	struct st21nfca_hci_info *info = from_timer(info, t, se_info.bwi_timer);
+
+	schedule_work(&info->se_info.timeout_work);
+}
+
 static void st21nfca_se_activation_timeout(struct timer_list *t)
 {
 	struct st21nfca_hci_info *info = from_timer(info, t,
@@ -296,6 +310,8 @@
 	int r = 0;
 	struct device *dev = &hdev->ndev->dev;
 	struct nfc_evt_transaction *transaction;
+	u32 aid_len;
+	u8 params_len;
 
 	pr_debug("connectivity gate event: %x\n", event);
 
@@ -304,33 +320,48 @@
 		r = nfc_se_connectivity(hdev->ndev, host);
 	break;
 	case ST21NFCA_EVT_TRANSACTION:
-		/*
-		 * According to specification etsi 102 622
+		/* According to specification etsi 102 622
 		 * 11.2.2.4 EVT_TRANSACTION Table 52
 		 * Description	Tag	Length
 		 * AID		81	5 to 16
 		 * PARAMETERS	82	0 to 255
+		 *
+		 * The key differences are aid storage length is variably sized
+		 * in the packet, but fixed in nfc_evt_transaction, and that the aid_len
+		 * is u8 in the packet, but u32 in the structure, and the tags in
+		 * the packet are not included in nfc_evt_transaction.
+		 *
+		 * size in bytes: 1          1       5-16 1             1           0-255
+		 * offset:        0          1       2    aid_len + 2   aid_len + 3 aid_len + 4
+		 * member name:   aid_tag(M) aid_len aid  params_tag(M) params_len  params
+		 * example:       0x81       5-16    X    0x82 0-255    X
 		 */
-		if (skb->len < NFC_MIN_AID_LENGTH + 2 &&
-		    skb->data[0] != NFC_EVT_TRANSACTION_AID_TAG)
+		if (skb->len < 2 || skb->data[0] != NFC_EVT_TRANSACTION_AID_TAG)
 			return -EPROTO;
 
-		transaction = devm_kzalloc(dev, skb->len - 2, GFP_KERNEL);
+		aid_len = skb->data[1];
+
+		if (skb->len < aid_len + 4 || aid_len > sizeof(transaction->aid))
+			return -EPROTO;
+
+		params_len = skb->data[aid_len + 3];
+
+		/* Verify PARAMETERS tag is (82), and final check that there is enough
+		 * space in the packet to read everything.
+		 */
+		if ((skb->data[aid_len + 2] != NFC_EVT_TRANSACTION_PARAMS_TAG) ||
+		    (skb->len < aid_len + 4 + params_len))
+			return -EPROTO;
+
+		transaction = devm_kzalloc(dev, sizeof(*transaction) + params_len, GFP_KERNEL);
 		if (!transaction)
 			return -ENOMEM;
 
-		transaction->aid_len = skb->data[1];
-		memcpy(transaction->aid, &skb->data[2],
-		       transaction->aid_len);
-
-		/* Check next byte is PARAMETERS tag (82) */
-		if (skb->data[transaction->aid_len + 2] !=
-		    NFC_EVT_TRANSACTION_PARAMS_TAG)
-			return -EPROTO;
+		transaction->aid_len = aid_len;
+		transaction->params_len = params_len;
 
-		transaction->params_len = skb->data[transaction->aid_len + 3];
-		memcpy(transaction->params, skb->data +
-		       transaction->aid_len + 4, transaction->params_len);
+		memcpy(transaction->aid, &skb->data[2], aid_len);
+		memcpy(transaction->params, &skb->data[aid_len + 4], params_len);
 
 		r = nfc_se_transaction(hdev->ndev, host, transaction);
 	break;
@@ -354,6 +385,7 @@
 	switch (event) {
 	case ST21NFCA_EVT_TRANSMIT_DATA:
 		del_timer_sync(&info->se_info.bwi_timer);
+		cancel_work_sync(&info->se_info.timeout_work);
 		info->se_info.bwi_active = false;
 		r = nfc_hci_send_event(hdev, ST21NFCA_DEVICE_MGNT_GATE,
 				ST21NFCA_EVT_SE_END_OF_APDU_TRANSFER, NULL, 0);
@@ -383,6 +415,7 @@
 	struct st21nfca_hci_info *info = nfc_hci_get_clientdata(hdev);
 
 	init_completion(&info->se_info.req_completion);
+	INIT_WORK(&info->se_info.timeout_work, st21nfca_se_wt_work);
 	/* initialize timers */
 	timer_setup(&info->se_info.bwi_timer, st21nfca_se_wt_timeout, 0);
 	info->se_info.bwi_active = false;
@@ -410,6 +443,7 @@
 	if (info->se_info.se_active)
 		del_timer_sync(&info->se_info.se_active_timer);
 
+	cancel_work_sync(&info->se_info.timeout_work);
 	info->se_info.bwi_active = false;
 	info->se_info.se_active = false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/st21nfca/st21nfca.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/st21nfca/st21nfca.h
@@ -141,6 +141,7 @@
 
 	se_io_cb_t cb;
 	void *cb_context;
+	struct work_struct timeout_work;
 };
 
 struct st21nfca_hci_info {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/trf7970a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/trf7970a.c
@@ -424,7 +424,8 @@
 	enum trf7970a_state		state;
 	struct device			*dev;
 	struct spi_device		*spi;
-	struct regulator		*regulator;
+	struct regulator		*vin_regulator;
+	struct regulator		*vddio_regulator;
 	struct nfc_digital_dev		*ddev;
 	u32				quirks;
 	bool				is_initiator;
@@ -1883,7 +1884,7 @@
 	if (trf->state != TRF7970A_ST_PWR_OFF)
 		return 0;
 
-	ret = regulator_enable(trf->regulator);
+	ret = regulator_enable(trf->vin_regulator);
 	if (ret) {
 		dev_err(trf->dev, "%s - Can't enable VIN: %d\n", __func__, ret);
 		return ret;
@@ -1926,7 +1927,7 @@
 	if (trf->en2_gpiod && !(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW))
 		gpiod_set_value_cansleep(trf->en2_gpiod, 0);
 
-	ret = regulator_disable(trf->regulator);
+	ret = regulator_disable(trf->vin_regulator);
 	if (ret)
 		dev_err(trf->dev, "%s - Can't disable VIN: %d\n", __func__,
 			ret);
@@ -2065,37 +2066,37 @@
 	mutex_init(&trf->lock);
 	INIT_DELAYED_WORK(&trf->timeout_work, trf7970a_timeout_work_handler);
 
-	trf->regulator = devm_regulator_get(&spi->dev, "vin");
-	if (IS_ERR(trf->regulator)) {
-		ret = PTR_ERR(trf->regulator);
+	trf->vin_regulator = devm_regulator_get(&spi->dev, "vin");
+	if (IS_ERR(trf->vin_regulator)) {
+		ret = PTR_ERR(trf->vin_regulator);
 		dev_err(trf->dev, "Can't get VIN regulator: %d\n", ret);
 		goto err_destroy_lock;
 	}
 
-	ret = regulator_enable(trf->regulator);
+	ret = regulator_enable(trf->vin_regulator);
 	if (ret) {
 		dev_err(trf->dev, "Can't enable VIN: %d\n", ret);
 		goto err_destroy_lock;
 	}
 
-	uvolts = regulator_get_voltage(trf->regulator);
+	uvolts = regulator_get_voltage(trf->vin_regulator);
 	if (uvolts > 4000000)
 		trf->chip_status_ctrl = TRF7970A_CHIP_STATUS_VRS5_3;
 
-	trf->regulator = devm_regulator_get(&spi->dev, "vdd-io");
-	if (IS_ERR(trf->regulator)) {
-		ret = PTR_ERR(trf->regulator);
+	trf->vddio_regulator = devm_regulator_get(&spi->dev, "vdd-io");
+	if (IS_ERR(trf->vddio_regulator)) {
+		ret = PTR_ERR(trf->vddio_regulator);
 		dev_err(trf->dev, "Can't get VDD_IO regulator: %d\n", ret);
-		goto err_destroy_lock;
+		goto err_disable_vin_regulator;
 	}
 
-	ret = regulator_enable(trf->regulator);
+	ret = regulator_enable(trf->vddio_regulator);
 	if (ret) {
 		dev_err(trf->dev, "Can't enable VDD_IO: %d\n", ret);
-		goto err_destroy_lock;
+		goto err_disable_vin_regulator;
 	}
 
-	if (regulator_get_voltage(trf->regulator) == 1800000) {
+	if (regulator_get_voltage(trf->vddio_regulator) == 1800000) {
 		trf->io_ctrl = TRF7970A_REG_IO_CTRL_IO_LOW;
 		dev_dbg(trf->dev, "trf7970a config vdd_io to 1.8V\n");
 	}
@@ -2108,7 +2109,7 @@
 	if (!trf->ddev) {
 		dev_err(trf->dev, "Can't allocate NFC digital device\n");
 		ret = -ENOMEM;
-		goto err_disable_regulator;
+		goto err_disable_vddio_regulator;
 	}
 
 	nfc_digital_set_parent_dev(trf->ddev, trf->dev);
@@ -2137,8 +2138,10 @@
 	trf7970a_shutdown(trf);
 err_free_ddev:
 	nfc_digital_free_device(trf->ddev);
-err_disable_regulator:
-	regulator_disable(trf->regulator);
+err_disable_vddio_regulator:
+	regulator_disable(trf->vddio_regulator);
+err_disable_vin_regulator:
+	regulator_disable(trf->vin_regulator);
 err_destroy_lock:
 	mutex_destroy(&trf->lock);
 	return ret;
@@ -2157,7 +2160,8 @@
 	nfc_digital_unregister_device(trf->ddev);
 	nfc_digital_free_device(trf->ddev);
 
-	regulator_disable(trf->regulator);
+	regulator_disable(trf->vddio_regulator);
+	regulator_disable(trf->vin_regulator);
 
 	mutex_destroy(&trf->lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nfc/virtual_ncidev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nfc/virtual_ncidev.c
@@ -54,16 +54,19 @@
 	mutex_lock(&nci_mutex);
 	if (state != virtual_ncidev_enabled) {
 		mutex_unlock(&nci_mutex);
+		kfree_skb(skb);
 		return 0;
 	}
 
 	if (send_buff) {
 		mutex_unlock(&nci_mutex);
+		kfree_skb(skb);
 		return -1;
 	}
 	send_buff = skb_copy(skb, GFP_KERNEL);
 	mutex_unlock(&nci_mutex);
 	wake_up_interruptible(&wq);
+	consume_skb(skb);
 
 	return 0;
 }
@@ -118,6 +121,10 @@
 		kfree_skb(skb);
 		return -EFAULT;
 	}
+	if (strnlen(skb->data, count) != count) {
+		kfree_skb(skb);
+		return -EINVAL;
+	}
 
 	nci_recv_frame(ndev, skb);
 	return count;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/core.c
@@ -100,6 +100,8 @@
 
 int ntb_register_device(struct ntb_dev *ntb)
 {
+	int ret;
+
 	if (!ntb)
 		return -EINVAL;
 	if (!ntb->pdev)
@@ -120,7 +122,11 @@
 	ntb->ctx_ops = NULL;
 	spin_lock_init(&ntb->ctx_lock);
 
-	return device_register(&ntb->dev);
+	ret = device_register(&ntb->dev);
+	if (ret)
+		put_device(&ntb->dev);
+
+	return ret;
 }
 EXPORT_SYMBOL(ntb_register_device);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/amd/ntb_hw_amd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/amd/ntb_hw_amd.c
@@ -1336,12 +1336,17 @@
 
 static int __init amd_ntb_pci_driver_init(void)
 {
+	int ret;
 	pr_info("%s %s\n", NTB_DESC, NTB_VER);
 
 	if (debugfs_initialized())
 		debugfs_dir = debugfs_create_dir(KBUILD_MODNAME, NULL);
 
-	return pci_register_driver(&amd_ntb_pci_driver);
+	ret = pci_register_driver(&amd_ntb_pci_driver);
+	if (ret)
+		debugfs_remove_recursive(debugfs_dir);
+
+	return ret;
 }
 module_init(amd_ntb_pci_driver_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/idt/ntb_hw_idt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/idt/ntb_hw_idt.c
@@ -2891,6 +2891,7 @@
 
 static int __init idt_pci_driver_init(void)
 {
+	int ret;
 	pr_info("%s %s\n", NTB_DESC, NTB_VER);
 
 	/* Create the top DebugFS directory if the FS is initialized */
@@ -2898,7 +2899,11 @@
 		dbgfs_topdir = debugfs_create_dir(KBUILD_MODNAME, NULL);
 
 	/* Register the NTB hardware driver to handle the PCI device */
-	return pci_register_driver(&idt_pci_driver);
+	ret = pci_register_driver(&idt_pci_driver);
+	if (ret)
+		debugfs_remove_recursive(dbgfs_topdir);
+
+	return ret;
 }
 module_init(idt_pci_driver_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/intel/ntb_hw_gen1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/intel/ntb_hw_gen1.c
@@ -778,7 +778,7 @@
 		ndev->debugfs_dir =
 			debugfs_create_dir(pci_name(ndev->ntb.pdev),
 					   debugfs_dir);
-		if (!ndev->debugfs_dir)
+		if (IS_ERR(ndev->debugfs_dir))
 			ndev->debugfs_info = NULL;
 		else
 			ndev->debugfs_info =
@@ -2060,12 +2060,17 @@
 
 static int __init intel_ntb_pci_driver_init(void)
 {
+	int ret;
 	pr_info("%s %s\n", NTB_DESC, NTB_VER);
 
 	if (debugfs_initialized())
 		debugfs_dir = debugfs_create_dir(KBUILD_MODNAME, NULL);
 
-	return pci_register_driver(&intel_ntb_pci_driver);
+	ret = pci_register_driver(&intel_ntb_pci_driver);
+	if (ret)
+		debugfs_remove_recursive(debugfs_dir);
+
+	return ret;
 }
 module_init(intel_ntb_pci_driver_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/intel/ntb_hw_gen3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/intel/ntb_hw_gen3.c
@@ -215,6 +215,9 @@
 	}
 
 	ndev->db_valid_mask = BIT_ULL(ndev->db_count) - 1;
+	/* Make sure we are not using DB's used for link status */
+	if (ndev->hwerr_flags & NTB_HWERR_MSIX_VECTOR32_BAD)
+		ndev->db_valid_mask &= ~ndev->db_link_mask;
 
 	ndev->reg->db_iowrite(ndev->db_valid_mask,
 			      ndev->self_mmio +
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/intel/ntb_hw_gen4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/intel/ntb_hw_gen4.c
@@ -168,6 +168,18 @@
 	return NTB_TOPO_NONE;
 }
 
+static enum ntb_topo spr_ppd_topo(struct intel_ntb_dev *ndev, u32 ppd)
+{
+	switch (ppd & SPR_PPD_TOPO_MASK) {
+	case SPR_PPD_TOPO_B2B_USD:
+		return NTB_TOPO_B2B_USD;
+	case SPR_PPD_TOPO_B2B_DSD:
+		return NTB_TOPO_B2B_DSD;
+	}
+
+	return NTB_TOPO_NONE;
+}
+
 int gen4_init_dev(struct intel_ntb_dev *ndev)
 {
 	struct pci_dev *pdev = ndev->ntb.pdev;
@@ -183,7 +195,10 @@
 	}
 
 	ppd1 = ioread32(ndev->self_mmio + GEN4_PPD1_OFFSET);
-	ndev->ntb.topo = gen4_ppd_topo(ndev, ppd1);
+	if (pdev_is_ICX(pdev))
+		ndev->ntb.topo = gen4_ppd_topo(ndev, ppd1);
+	else if (pdev_is_SPR(pdev))
+		ndev->ntb.topo = spr_ppd_topo(ndev, ppd1);
 	dev_dbg(&pdev->dev, "ppd %#x topo %s\n", ppd1,
 		ntb_topo_string(ndev->ntb.topo));
 	if (ndev->ntb.topo == NTB_TOPO_NONE)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/intel/ntb_hw_gen4.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/intel/ntb_hw_gen4.h
@@ -49,10 +49,14 @@
 #define GEN4_PPD_CLEAR_TRN		0x0001
 #define GEN4_PPD_LINKTRN		0x0008
 #define GEN4_PPD_CONN_MASK		0x0300
+#define SPR_PPD_CONN_MASK		0x0700
 #define GEN4_PPD_CONN_B2B		0x0200
 #define GEN4_PPD_DEV_MASK		0x1000
 #define GEN4_PPD_DEV_DSD		0x1000
 #define GEN4_PPD_DEV_USD		0x0000
+#define SPR_PPD_DEV_MASK		0x4000
+#define SPR_PPD_DEV_DSD 		0x4000
+#define SPR_PPD_DEV_USD 		0x0000
 #define GEN4_LINK_CTRL_LINK_DISABLE	0x0010
 
 #define GEN4_SLOTSTS			0xb05a
@@ -62,6 +66,10 @@
 #define GEN4_PPD_TOPO_B2B_USD	(GEN4_PPD_CONN_B2B | GEN4_PPD_DEV_USD)
 #define GEN4_PPD_TOPO_B2B_DSD	(GEN4_PPD_CONN_B2B | GEN4_PPD_DEV_DSD)
 
+#define SPR_PPD_TOPO_MASK	(SPR_PPD_CONN_MASK | SPR_PPD_DEV_MASK)
+#define SPR_PPD_TOPO_B2B_USD	(GEN4_PPD_CONN_B2B | SPR_PPD_DEV_USD)
+#define SPR_PPD_TOPO_B2B_DSD	(GEN4_PPD_CONN_B2B | SPR_PPD_DEV_DSD)
+
 #define GEN4_DB_COUNT			32
 #define GEN4_DB_LINK			32
 #define GEN4_DB_LINK_BIT		BIT_ULL(GEN4_DB_LINK)
@@ -111,5 +119,13 @@
 		return 1;
 	return 0;
 }
+
+static inline int pdev_is_SPR(struct pci_dev *pdev)
+{
+	if (pdev_is_gen4(pdev) &&
+	    pdev->revision > PCI_DEVICE_REVISION_ICX_MAX)
+		return 1;
+	return 0;
+}
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/hw/mscc/ntb_hw_switchtec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/hw/mscc/ntb_hw_switchtec.c
@@ -288,7 +288,7 @@
 	if (size != 0 && xlate_pos < 12)
 		return -EINVAL;
 
-	if (!IS_ALIGNED(addr, BIT_ULL(xlate_pos))) {
+	if (xlate_pos >= 0 && !IS_ALIGNED(addr, BIT_ULL(xlate_pos))) {
 		/*
 		 * In certain circumstances we can get a buffer that is
 		 * not aligned to its size. (Most of the time
@@ -419,8 +419,8 @@
 					  enum ntb_width *width)
 {
 	struct switchtec_dev *stdev = sndev->stdev;
-
-	u32 pff = ioread32(&stdev->mmio_part_cfg[partition].vep_pff_inst_id);
+	u32 pff =
+		ioread32(&stdev->mmio_part_cfg_all[partition].vep_pff_inst_id);
 	u32 linksta = ioread32(&stdev->mmio_pff_csr[pff].pci_cap_region[13]);
 
 	if (speed)
@@ -840,7 +840,6 @@
 	u64 tpart_vec;
 	int self;
 	u64 part_map;
-	int bit;
 
 	sndev->ntb.pdev = sndev->stdev->pdev;
 	sndev->ntb.topo = NTB_TOPO_SWITCH;
@@ -861,29 +860,28 @@
 	part_map = ioread64(&sndev->mmio_ntb->ep_map);
 	part_map &= ~(1 << sndev->self_partition);
 
-	if (!ffs(tpart_vec)) {
+	if (!tpart_vec) {
 		if (sndev->stdev->partition_count != 2) {
 			dev_err(&sndev->stdev->dev,
 				"ntb target partition not defined\n");
 			return -ENODEV;
 		}
 
-		bit = ffs(part_map);
-		if (!bit) {
+		if (!part_map) {
 			dev_err(&sndev->stdev->dev,
 				"peer partition is not NT partition\n");
 			return -ENODEV;
 		}
 
-		sndev->peer_partition = bit - 1;
+		sndev->peer_partition = __ffs64(part_map);
 	} else {
-		if (ffs(tpart_vec) != fls(tpart_vec)) {
+		if (__ffs64(tpart_vec) != (fls64(tpart_vec) - 1)) {
 			dev_err(&sndev->stdev->dev,
 				"ntb driver only supports 1 pair of 1-1 ntb mapping\n");
 			return -ENODEV;
 		}
 
-		sndev->peer_partition = ffs(tpart_vec) - 1;
+		sndev->peer_partition = __ffs64(tpart_vec);
 		if (!(part_map & (1ULL << sndev->peer_partition))) {
 			dev_err(&sndev->stdev->dev,
 				"ntb target partition is not NT partition\n");
@@ -1558,6 +1556,7 @@
 	switchtec_ntb_deinit_db_msg_irq(sndev);
 	switchtec_ntb_deinit_shared_mw(sndev);
 	switchtec_ntb_deinit_crosslink(sndev);
+	cancel_work_sync(&sndev->check_link_status_work);
 	kfree(sndev);
 	dev_info(dev, "ntb device unregistered\n");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/ntb_transport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/ntb_transport.c
@@ -410,7 +410,7 @@
 
 		rc = device_register(dev);
 		if (rc) {
-			kfree(client_dev);
+			put_device(dev);
 			goto err;
 		}
 
@@ -909,7 +909,7 @@
 	return 0;
 }
 
-static void ntb_qp_link_down_reset(struct ntb_transport_qp *qp)
+static void ntb_qp_link_context_reset(struct ntb_transport_qp *qp)
 {
 	qp->link_is_up = false;
 	qp->active = false;
@@ -932,6 +932,13 @@
 	qp->tx_async = 0;
 }
 
+static void ntb_qp_link_down_reset(struct ntb_transport_qp *qp)
+{
+	ntb_qp_link_context_reset(qp);
+	if (qp->remote_rx_info)
+		qp->remote_rx_info->entry = qp->rx_max_entry - 1;
+}
+
 static void ntb_qp_link_cleanup(struct ntb_transport_qp *qp)
 {
 	struct ntb_transport_ctx *nt = qp->transport;
@@ -1174,7 +1181,7 @@
 	qp->ndev = nt->ndev;
 	qp->client_ready = false;
 	qp->event_handler = NULL;
-	ntb_qp_link_down_reset(qp);
+	ntb_qp_link_context_reset(qp);
 
 	if (mw_num < qp_count % mw_count)
 		num_qps_mw = qp_count / mw_count + 1;
@@ -2276,9 +2283,13 @@
 	struct ntb_queue_entry *entry;
 	int rc;
 
-	if (!qp || !qp->link_is_up || !len)
+	if (!qp || !len)
 		return -EINVAL;
 
+	/* If the qp link is down already, just ignore. */
+	if (!qp->link_is_up)
+		return 0;
+
 	entry = ntb_list_rm(&qp->ntb_tx_free_q_lock, &qp->tx_free_q);
 	if (!entry) {
 		qp->tx_err_no_buf++;
@@ -2418,7 +2429,7 @@
 	unsigned int head = qp->tx_index;
 	unsigned int tail = qp->remote_rx_info->entry;
 
-	return tail > head ? tail - head : qp->tx_max_entry + tail - head;
+	return tail >= head ? tail - head : qp->tx_max_entry + tail - head;
 }
 EXPORT_SYMBOL_GPL(ntb_transport_tx_free_entry);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/test/ntb_perf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/test/ntb_perf.c
@@ -839,10 +839,8 @@
 	dma_set_unmap(tx, unmap);
 
 	ret = dma_submit_error(dmaengine_submit(tx));
-	if (ret) {
-		dmaengine_unmap_put(unmap);
+	if (ret)
 		goto err_free_resource;
-	}
 
 	dmaengine_unmap_put(unmap);
 
@@ -1227,7 +1225,7 @@
 			"\tOut buffer addr 0x%pK\n", peer->outbuf);
 
 		pos += scnprintf(buf + pos, buf_size - pos,
-			"\tOut buff phys addr %pa[p]\n", &peer->out_phys_addr);
+			"\tOut buff phys addr %pap\n", &peer->out_phys_addr);
 
 		pos += scnprintf(buf + pos, buf_size - pos,
 			"\tOut buffer size %pa\n", &peer->outbuf_size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ntb/test/ntb_tool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ntb/test/ntb_tool.c
@@ -367,14 +367,16 @@
 	u64 bits;
 	int n;
 
+	if (*offp)
+		return 0;
+
 	buf = kmalloc(size + 1, GFP_KERNEL);
 	if (!buf)
 		return -ENOMEM;
 
-	ret = simple_write_to_buffer(buf, size, offp, ubuf, size);
-	if (ret < 0) {
+	if (copy_from_user(buf, ubuf, size)) {
 		kfree(buf);
-		return ret;
+		return -EFAULT;
 	}
 
 	buf[size] = 0;
@@ -996,6 +998,8 @@
 		tc->peers[pidx].outmws =
 			devm_kcalloc(&tc->ntb->dev, tc->peers[pidx].outmw_cnt,
 				   sizeof(*tc->peers[pidx].outmws), GFP_KERNEL);
+		if (tc->peers[pidx].outmws == NULL)
+			return -ENOMEM;
 
 		for (widx = 0; widx < tc->peers[pidx].outmw_cnt; widx++) {
 			tc->peers[pidx].outmws[widx].pidx = pidx;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nubus/proc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nubus/proc.c
@@ -137,6 +137,18 @@
 	return 0;
 }
 
+static int nubus_rsrc_proc_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, nubus_proc_rsrc_show, inode);
+}
+
+static const struct proc_ops nubus_rsrc_proc_ops = {
+	.proc_open	= nubus_rsrc_proc_open,
+	.proc_read	= seq_read,
+	.proc_lseek	= seq_lseek,
+	.proc_release	= single_release,
+};
+
 void nubus_proc_add_rsrc_mem(struct proc_dir_entry *procdir,
 			     const struct nubus_dirent *ent,
 			     unsigned int size)
@@ -152,8 +164,8 @@
 		pde_data = nubus_proc_alloc_pde_data(nubus_dirptr(ent), size);
 	else
 		pde_data = NULL;
-	proc_create_single_data(name, S_IFREG | 0444, procdir,
-			nubus_proc_rsrc_show, pde_data);
+	proc_create_data(name, S_IFREG | 0444, procdir,
+			 &nubus_rsrc_proc_ops, pde_data);
 }
 
 void nubus_proc_add_rsrc(struct proc_dir_entry *procdir,
@@ -166,9 +178,9 @@
 		return;
 
 	snprintf(name, sizeof(name), "%x", ent->type);
-	proc_create_single_data(name, S_IFREG | 0444, procdir,
-			nubus_proc_rsrc_show,
-			nubus_proc_alloc_pde_data(data, 0));
+	proc_create_data(name, S_IFREG | 0444, procdir,
+			 &nubus_rsrc_proc_ops,
+			 nubus_proc_alloc_pde_data(data, 0));
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/btt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/btt.c
@@ -1538,7 +1538,6 @@
 		int rc = nd_integrity_init(btt->btt_disk, btt_meta_size(btt));
 
 		if (rc) {
-			del_gendisk(btt->btt_disk);
 			blk_cleanup_disk(btt->btt_disk);
 			return rc;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/bus.c
@@ -185,8 +185,8 @@
 	ndr_end = nd_region->ndr_start + nd_region->ndr_size - 1;
 
 	/* make sure we are in the region */
-	if (ctx->phys < nd_region->ndr_start
-			|| (ctx->phys + ctx->cleared) > ndr_end)
+	if (ctx->phys < nd_region->ndr_start ||
+	    (ctx->phys + ctx->cleared - 1) > ndr_end)
 		return 0;
 
 	sector = (ctx->phys - nd_region->ndr_start) / 512;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/core.c
@@ -399,9 +399,7 @@
 	if (!nd_desc->fw_ops)
 		return -EOPNOTSUPP;
 
-	nvdimm_bus_lock(dev);
 	cap = nd_desc->fw_ops->capability(nd_desc);
-	nvdimm_bus_unlock(dev);
 
 	switch (cap) {
 	case NVDIMM_FWA_CAP_QUIESCE:
@@ -426,10 +424,8 @@
 	if (!nd_desc->fw_ops)
 		return -EOPNOTSUPP;
 
-	nvdimm_bus_lock(dev);
 	cap = nd_desc->fw_ops->capability(nd_desc);
 	state = nd_desc->fw_ops->activate_state(nd_desc);
-	nvdimm_bus_unlock(dev);
 
 	if (cap < NVDIMM_FWA_CAP_QUIESCE)
 		return -EOPNOTSUPP;
@@ -474,7 +470,6 @@
 	else
 		return -EINVAL;
 
-	nvdimm_bus_lock(dev);
 	state = nd_desc->fw_ops->activate_state(nd_desc);
 
 	switch (state) {
@@ -492,7 +487,6 @@
 	default:
 		rc = -ENXIO;
 	}
-	nvdimm_bus_unlock(dev);
 
 	if (rc == 0)
 		rc = len;
@@ -515,10 +509,7 @@
 	if (!nd_desc->fw_ops)
 		return 0;
 
-	nvdimm_bus_lock(dev);
 	cap = nd_desc->fw_ops->capability(nd_desc);
-	nvdimm_bus_unlock(dev);
-
 	if (cap < NVDIMM_FWA_CAP_QUIESCE)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/dax_devs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/dax_devs.c
@@ -106,12 +106,12 @@
 
 	nvdimm_bus_lock(&ndns->dev);
 	nd_dax = nd_dax_alloc(nd_region);
-	nd_pfn = &nd_dax->nd_pfn;
-	dax_dev = nd_pfn_devinit(nd_pfn, ndns);
+	dax_dev = nd_dax_devinit(nd_dax, ndns);
 	nvdimm_bus_unlock(&ndns->dev);
 	if (!dax_dev)
 		return -ENOMEM;
 	pfn_sb = devm_kmalloc(dev, sizeof(*pfn_sb), GFP_KERNEL);
+	nd_pfn = &nd_dax->nd_pfn;
 	nd_pfn->pfn_sb = pfn_sb;
 	rc = nd_pfn_validate(nd_pfn, DAX_SIG);
 	dev_dbg(dev, "dax: %s\n", rc == 0 ? dev_name(dax_dev) : "<none>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/nd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/nd.h
@@ -485,6 +485,13 @@
 int nd_dax_probe(struct device *dev, struct nd_namespace_common *ndns);
 bool is_nd_dax(struct device *dev);
 struct device *nd_dax_create(struct nd_region *nd_region);
+static inline struct device *nd_dax_devinit(struct nd_dax *nd_dax,
+					    struct nd_namespace_common *ndns)
+{
+	if (!nd_dax)
+		return NULL;
+	return nd_pfn_devinit(&nd_dax->nd_pfn, ndns);
+}
 #else
 static inline int nd_dax_probe(struct device *dev,
 		struct nd_namespace_common *ndns)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/nd_virtio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/nd_virtio.c
@@ -44,6 +44,15 @@
 	unsigned long flags;
 	int err, err1;
 
+	/*
+	 * Don't bother to submit the request to the device if the device is
+	 * not activated.
+	 */
+	if (vdev->config->get_status(vdev) & VIRTIO_CONFIG_S_NEEDS_RESET) {
+		dev_info(&vdev->dev, "virtio pmem device needs a reset\n");
+		return -EIO;
+	}
+
 	might_sleep();
 	req_data = kmalloc(sizeof(*req_data), GFP_KERNEL);
 	if (!req_data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/of_pmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/of_pmem.c
@@ -30,7 +30,13 @@
 	if (!priv)
 		return -ENOMEM;
 
-	priv->bus_desc.provider_name = kstrdup(pdev->name, GFP_KERNEL);
+	priv->bus_desc.provider_name = devm_kstrdup(&pdev->dev, pdev->name,
+							GFP_KERNEL);
+	if (!priv->bus_desc.provider_name) {
+		kfree(priv);
+		return -ENOMEM;
+	}
+
 	priv->bus_desc.module = THIS_MODULE;
 	priv->bus_desc.of_node = np;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/pmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/pmem.c
@@ -429,8 +429,10 @@
 		bb_range.end = res->end;
 	}
 
-	if (IS_ERR(addr))
-		return PTR_ERR(addr);
+	if (IS_ERR(addr)) {
+		rc = PTR_ERR(addr);
+		goto out;
+	}
 	pmem->virt_addr = addr;
 
 	blk_queue_write_cache(q, true, fua);
@@ -455,7 +457,8 @@
 		flags = DAXDEV_F_SYNC;
 	dax_dev = alloc_dax(pmem, disk->disk_name, &pmem_dax_ops, flags);
 	if (IS_ERR(dax_dev)) {
-		return PTR_ERR(dax_dev);
+		rc = PTR_ERR(dax_dev);
+		goto out;
 	}
 	dax_write_cache(dax_dev, nvdimm_has_cache(nd_region));
 	pmem->dax_dev = dax_dev;
@@ -470,8 +473,10 @@
 					  "badblocks");
 	if (!pmem->bb_state)
 		dev_warn(dev, "'badblocks' notification disabled\n");
-
 	return 0;
+out:
+	blk_cleanup_disk(pmem->disk);
+	return rc;
 }
 
 static int nd_pmem_probe(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/region_devs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/region_devs.c
@@ -966,7 +966,8 @@
 {
 	unsigned int cpu, lane;
 
-	cpu = get_cpu();
+	migrate_disable();
+	cpu = smp_processor_id();
 	if (nd_region->num_lanes < nr_cpu_ids) {
 		struct nd_percpu_lane *ndl_lock, *ndl_count;
 
@@ -985,16 +986,15 @@
 void nd_region_release_lane(struct nd_region *nd_region, unsigned int lane)
 {
 	if (nd_region->num_lanes < nr_cpu_ids) {
-		unsigned int cpu = get_cpu();
+		unsigned int cpu = smp_processor_id();
 		struct nd_percpu_lane *ndl_lock, *ndl_count;
 
 		ndl_count = per_cpu_ptr(nd_region->lane, cpu);
 		ndl_lock = per_cpu_ptr(nd_region->lane, lane);
 		if (--ndl_count->count == 0)
 			spin_unlock(&ndl_lock->lock);
-		put_cpu();
 	}
-	put_cpu();
+	migrate_enable();
 }
 EXPORT_SYMBOL(nd_region_release_lane);
 
@@ -1025,6 +1025,9 @@
 		}
 	}
 
+	if (nd_region->ndr_size < MEMREMAP_COMPAT_ALIGN_MAX)
+		align = PAGE_SIZE;
+
 	mappings = max_t(u16, 1, nd_region->ndr_mappings);
 	div_u64_rem(align, mappings, &remainder);
 	if (remainder)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvdimm/security.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvdimm/security.c
@@ -379,11 +379,6 @@
 			|| !nvdimm->sec.flags)
 		return -EOPNOTSUPP;
 
-	if (dev->driver == NULL) {
-		dev_dbg(dev, "Unable to overwrite while DIMM active.\n");
-		return -EINVAL;
-	}
-
 	rc = check_security_state(nvdimm);
 	if (rc)
 		return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/core.c
@@ -131,7 +131,7 @@
 	if (test_and_set_bit(NVME_NS_DEAD, &ns->flags))
 		return;
 
-	blk_set_queue_dying(ns->queue);
+	blk_mark_disk_dead(ns->disk);
 	blk_mq_unquiesce_queue(ns->queue);
 
 	set_capacity_and_notify(ns->disk, 0);
@@ -444,8 +444,6 @@
 	switch (new_state) {
 	case NVME_CTRL_LIVE:
 		switch (old_state) {
-		case NVME_CTRL_NEW:
-		case NVME_CTRL_RESETTING:
 		case NVME_CTRL_CONNECTING:
 			changed = true;
 			fallthrough;
@@ -853,16 +851,26 @@
 		range = page_address(ns->ctrl->discard_page);
 	}
 
-	__rq_for_each_bio(bio, req) {
-		u64 slba = nvme_sect_to_lba(ns, bio->bi_iter.bi_sector);
-		u32 nlb = bio->bi_iter.bi_size >> ns->lba_shift;
-
-		if (n < segments) {
-			range[n].cattr = cpu_to_le32(0);
-			range[n].nlb = cpu_to_le32(nlb);
-			range[n].slba = cpu_to_le64(slba);
+	if (queue_max_discard_segments(req->q) == 1) {
+		u64 slba = nvme_sect_to_lba(ns, blk_rq_pos(req));
+		u32 nlb = blk_rq_sectors(req) >> (ns->lba_shift - 9);
+
+		range[0].cattr = cpu_to_le32(0);
+		range[0].nlb = cpu_to_le32(nlb);
+		range[0].slba = cpu_to_le64(slba);
+		n = 1;
+	} else {
+		__rq_for_each_bio(bio, req) {
+			u64 slba = nvme_sect_to_lba(ns, bio->bi_iter.bi_sector);
+			u32 nlb = bio->bi_iter.bi_size >> ns->lba_shift;
+
+			if (n < segments) {
+				range[n].cattr = cpu_to_le32(0);
+				range[n].nlb = cpu_to_le32(nlb);
+				range[n].slba = cpu_to_le64(slba);
+			}
+			n++;
 		}
-		n++;
 	}
 
 	if (WARN_ON_ONCE(n != segments)) {
@@ -971,6 +979,7 @@
 			clear_bit_unlock(0, &ctrl->discard_page_busy);
 		else
 			kfree(bvec_virt(&req->special_vec));
+		req->rq_flags &= ~RQF_SPECIAL_PAYLOAD;
 	}
 }
 EXPORT_SYMBOL_GPL(nvme_cleanup_cmd);
@@ -1113,6 +1122,18 @@
 	return 0;
 }
 
+static u32 nvme_known_nvm_effects(u8 opcode)
+{
+	switch (opcode) {
+	case nvme_cmd_write:
+	case nvme_cmd_write_zeroes:
+	case nvme_cmd_write_uncor:
+		 return NVME_CMD_EFFECTS_LBCC;
+	default:
+		return 0;
+	}
+}
+
 u32 nvme_command_effects(struct nvme_ctrl *ctrl, struct nvme_ns *ns, u8 opcode)
 {
 	u32 effects = 0;
@@ -1120,16 +1141,24 @@
 	if (ns) {
 		if (ns->head->effects)
 			effects = le32_to_cpu(ns->head->effects->iocs[opcode]);
+		if (ns->head->ids.csi == NVME_CSI_NVM)
+			effects |= nvme_known_nvm_effects(opcode);
 		if (effects & ~(NVME_CMD_EFFECTS_CSUPP | NVME_CMD_EFFECTS_LBCC))
 			dev_warn_once(ctrl->device,
-				"IO command:%02x has unhandled effects:%08x\n",
+				"IO command:%02x has unusual effects:%08x\n",
 				opcode, effects);
-		return 0;
-	}
 
-	if (ctrl->effects)
-		effects = le32_to_cpu(ctrl->effects->acs[opcode]);
-	effects |= nvme_known_admin_effects(opcode);
+		/*
+		 * NVME_CMD_EFFECTS_CSE_MASK causes a freeze all I/O queues,
+		 * which would deadlock when done on an I/O command.  Note that
+		 * We already warn about an unusual effect above.
+		 */
+		effects &= ~NVME_CMD_EFFECTS_CSE_MASK;
+	} else {
+		if (ctrl->effects)
+			effects = le32_to_cpu(ctrl->effects->acs[opcode]);
+		effects |= nvme_known_admin_effects(opcode);
+	}
 
 	return effects;
 }
@@ -1155,7 +1184,7 @@
 	return effects;
 }
 
-static void nvme_passthru_end(struct nvme_ctrl *ctrl, u32 effects,
+static void nvme_passthru_end(struct nvme_ctrl *ctrl, struct nvme_ns *ns, u32 effects,
 			      struct nvme_command *cmd, int status)
 {
 	if (effects & NVME_CMD_EFFECTS_CSE_MASK) {
@@ -1171,6 +1200,8 @@
 		nvme_queue_scan(ctrl);
 		flush_work(&ctrl->scan_work);
 	}
+	if (ns)
+		return;
 
 	switch (cmd->common.opcode) {
 	case nvme_admin_set_features:
@@ -1205,7 +1236,7 @@
 	effects = nvme_passthru_start(ctrl, ns, cmd->common.opcode);
 	ret = nvme_execute_rq(disk, rq, false);
 	if (effects) /* nothing to be done for zero cmd effects */
-		nvme_passthru_end(ctrl, effects, cmd, ret);
+		nvme_passthru_end(ctrl, ns, effects, cmd, ret);
 
 	return ret;
 }
@@ -1217,9 +1248,25 @@
  *   The host should send Keep Alive commands at half of the Keep Alive Timeout
  *   accounting for transport roundtrip times [..].
  */
+static unsigned long nvme_keep_alive_work_period(struct nvme_ctrl *ctrl)
+{
+	unsigned long delay = ctrl->kato * HZ / 2;
+
+	/*
+	 * When using Traffic Based Keep Alive, we need to run
+	 * nvme_keep_alive_work at twice the normal frequency, as one
+	 * command completion can postpone sending a keep alive command
+	 * by up to twice the delay between runs.
+	 */
+	if (ctrl->ctratt & NVME_CTRL_ATTR_TBKAS)
+		delay /= 2;
+	return delay;
+}
+
 static void nvme_queue_keep_alive_work(struct nvme_ctrl *ctrl)
 {
-	queue_delayed_work(nvme_wq, &ctrl->ka_work, ctrl->kato * HZ / 2);
+	queue_delayed_work(nvme_wq, &ctrl->ka_work,
+			   nvme_keep_alive_work_period(ctrl));
 }
 
 static void nvme_keep_alive_end_io(struct request *rq, blk_status_t status)
@@ -1354,6 +1401,8 @@
 				 warn_str, cur->nidl);
 			return -1;
 		}
+		if (ctrl->quirks & NVME_QUIRK_BOGUS_NID)
+			return NVME_NIDT_EUI64_LEN;
 		memcpy(ids->eui64, data + sizeof(*cur), NVME_NIDT_EUI64_LEN);
 		return NVME_NIDT_EUI64_LEN;
 	case NVME_NIDT_NGUID:
@@ -1362,6 +1411,8 @@
 				 warn_str, cur->nidl);
 			return -1;
 		}
+		if (ctrl->quirks & NVME_QUIRK_BOGUS_NID)
+			return NVME_NIDT_NGUID_LEN;
 		memcpy(ids->nguid, data + sizeof(*cur), NVME_NIDT_NGUID_LEN);
 		return NVME_NIDT_NGUID_LEN;
 	case NVME_NIDT_UUID:
@@ -1370,6 +1421,8 @@
 				 warn_str, cur->nidl);
 			return -1;
 		}
+		if (ctrl->quirks & NVME_QUIRK_BOGUS_NID)
+			return NVME_NIDT_UUID_LEN;
 		uuid_copy(&ids->uuid, data + sizeof(*cur));
 		return NVME_NIDT_UUID_LEN;
 	case NVME_NIDT_CSI:
@@ -1466,12 +1519,18 @@
 	if ((*id)->ncap == 0) /* namespace not allocated or attached */
 		goto out_free_id;
 
-	if (ctrl->vs >= NVME_VS(1, 1, 0) &&
-	    !memchr_inv(ids->eui64, 0, sizeof(ids->eui64)))
-		memcpy(ids->eui64, (*id)->eui64, sizeof(ids->eui64));
-	if (ctrl->vs >= NVME_VS(1, 2, 0) &&
-	    !memchr_inv(ids->nguid, 0, sizeof(ids->nguid)))
-		memcpy(ids->nguid, (*id)->nguid, sizeof(ids->nguid));
+
+	if (ctrl->quirks & NVME_QUIRK_BOGUS_NID) {
+		dev_info(ctrl->device,
+			 "Ignoring bogus Namespace Identifiers\n");
+	} else {
+		if (ctrl->vs >= NVME_VS(1, 1, 0) &&
+		    !memchr_inv(ids->eui64, 0, sizeof(ids->eui64)))
+			memcpy(ids->eui64, (*id)->eui64, sizeof(ids->eui64));
+		if (ctrl->vs >= NVME_VS(1, 2, 0) &&
+		    !memchr_inv(ids->nguid, 0, sizeof(ids->nguid)))
+			memcpy(ids->nguid, (*id)->nguid, sizeof(ids->nguid));
+	}
 
 	return 0;
 
@@ -1524,7 +1583,13 @@
 
 	status = nvme_set_features(ctrl, NVME_FEAT_NUM_QUEUES, q_count, NULL, 0,
 			&result);
-	if (status < 0)
+
+	/*
+	 * It's either a kernel error or the host observed a connection
+	 * lost. In either case it's not possible communicate with the
+	 * controller and thus enter the error code path.
+	 */
+	if (status < 0 || status == NVME_SC_HOST_PATH_ERROR)
 		return status;
 
 	/*
@@ -1674,13 +1739,6 @@
 		blk_queue_max_write_zeroes_sectors(queue, UINT_MAX);
 }
 
-static bool nvme_ns_ids_valid(struct nvme_ns_ids *ids)
-{
-	return !uuid_is_null(&ids->uuid) ||
-		memchr_inv(ids->nguid, 0, sizeof(ids->nguid)) ||
-		memchr_inv(ids->eui64, 0, sizeof(ids->eui64));
-}
-
 static bool nvme_ns_ids_equal(struct nvme_ns_ids *a, struct nvme_ns_ids *b)
 {
 	return uuid_equal(&a->uuid, &b->uuid) &&
@@ -1714,7 +1772,7 @@
 	return 0;
 }
 
-static int nvme_configure_metadata(struct nvme_ns *ns, struct nvme_id_ns *id)
+static void nvme_configure_metadata(struct nvme_ns *ns, struct nvme_id_ns *id)
 {
 	struct nvme_ctrl *ctrl = ns->ctrl;
 
@@ -1730,7 +1788,8 @@
 
 	ns->features &= ~(NVME_NS_METADATA_SUPPORTED | NVME_NS_EXT_LBAS);
 	if (!ns->ms || !(ctrl->ops->flags & NVME_F_METADATA_SUPPORTED))
-		return 0;
+		return;
+
 	if (ctrl->ops->flags & NVME_F_FABRICS) {
 		/*
 		 * The NVMe over Fabrics specification only supports metadata as
@@ -1738,10 +1797,21 @@
 		 * remap the separate metadata buffer from the block layer.
 		 */
 		if (WARN_ON_ONCE(!(id->flbas & NVME_NS_FLBAS_META_EXT)))
-			return -EINVAL;
-		if (ctrl->max_integrity_segments)
-			ns->features |=
-				(NVME_NS_METADATA_SUPPORTED | NVME_NS_EXT_LBAS);
+			return;
+
+		ns->features |= NVME_NS_EXT_LBAS;
+
+		/*
+		 * The current fabrics transport drivers support namespace
+		 * metadata formats only if nvme_ns_has_pi() returns true.
+		 * Suppress support for all other formats so the namespace will
+		 * have a 0 capacity and not be usable through the block stack.
+		 *
+		 * Note, this check will need to be modified if any drivers
+		 * gain the ability to use other metadata formats.
+		 */
+		if (ctrl->max_integrity_segments && nvme_ns_has_pi(ns))
+			ns->features |= NVME_NS_METADATA_SUPPORTED;
 	} else {
 		/*
 		 * For PCIe controllers, we can't easily remap the separate
@@ -1754,8 +1824,6 @@
 		else
 			ns->features |= NVME_NS_METADATA_SUPPORTED;
 	}
-
-	return 0;
 }
 
 static void nvme_set_queue_limits(struct nvme_ctrl *ctrl,
@@ -1772,7 +1840,7 @@
 		blk_queue_max_segments(q, min_t(u32, max_segments, USHRT_MAX));
 	}
 	blk_queue_virt_boundary(q, NVME_CTRL_PAGE_SIZE - 1);
-	blk_queue_dma_alignment(q, 7);
+	blk_queue_dma_alignment(q, 3);
 	blk_queue_write_cache(q, vwc, vwc);
 }
 
@@ -1785,9 +1853,10 @@
 
 	/*
 	 * The block layer can't support LBA sizes larger than the page size
-	 * yet, so catch this early and don't allow block I/O.
+	 * or smaller than a sector size yet, so catch this early and don't
+	 * allow block I/O.
 	 */
-	if (ns->lba_shift > PAGE_SHIFT) {
+	if (ns->lba_shift > PAGE_SHIFT || ns->lba_shift < SECTOR_SHIFT) {
 		capacity = 0;
 		bs = (1 << 9);
 	}
@@ -1845,9 +1914,6 @@
 	nvme_config_discard(disk, ns);
 	blk_queue_max_write_zeroes_sectors(disk->queue,
 					   ns->ctrl->max_zeroes_sectors);
-
-	set_disk_ro(disk, (id->nsattr & NVME_NS_ATTR_RO) ||
-		test_bit(NVME_NS_FORCE_RO, &ns->flags));
 }
 
 static inline bool nvme_first_scan(struct gendisk *disk)
@@ -1896,18 +1962,20 @@
 	ns->lba_shift = id->lbaf[lbaf].ds;
 	nvme_set_queue_limits(ns->ctrl, ns->queue);
 
-	ret = nvme_configure_metadata(ns, id);
-	if (ret)
-		goto out_unfreeze;
+	nvme_configure_metadata(ns, id);
 	nvme_set_chunk_sectors(ns, id);
 	nvme_update_disk_info(ns->disk, ns, id);
 
 	if (ns->head->ids.csi == NVME_CSI_ZNS) {
 		ret = nvme_update_zone_info(ns, lbaf);
-		if (ret)
-			goto out_unfreeze;
+		if (ret) {
+			blk_mq_unfreeze_queue(ns->disk->queue);
+			goto out;
+		}
 	}
 
+	set_disk_ro(ns->disk, (id->nsattr & NVME_NS_ATTR_RO) ||
+		test_bit(NVME_NS_FORCE_RO, &ns->flags));
 	set_bit(NVME_NS_READY, &ns->flags);
 	blk_mq_unfreeze_queue(ns->disk->queue);
 
@@ -1920,16 +1988,17 @@
 	if (nvme_ns_head_multipath(ns->head)) {
 		blk_mq_freeze_queue(ns->head->disk->queue);
 		nvme_update_disk_info(ns->head->disk, ns, id);
+		set_disk_ro(ns->head->disk,
+			    (id->nsattr & NVME_NS_ATTR_RO) ||
+				    test_bit(NVME_NS_FORCE_RO, &ns->flags));
 		nvme_mpath_revalidate_paths(ns);
 		blk_stack_limits(&ns->head->disk->queue->limits,
 				 &ns->queue->limits, 0);
 		disk_update_readahead(ns->head->disk);
 		blk_mq_unfreeze_queue(ns->head->disk->queue);
 	}
-	return 0;
 
-out_unfreeze:
-	blk_mq_unfreeze_queue(ns->disk->queue);
+	ret = 0;
 out:
 	/*
 	 * If probing fails due an unsupported feature, hide the block device,
@@ -1937,6 +2006,7 @@
 	 */
 	if (ret == -ENODEV) {
 		ns->disk->flags |= GENHD_FL_HIDDEN;
+		set_bit(NVME_NS_READY, &ns->flags);
 		ret = 0;
 	}
 	return ret;
@@ -2040,14 +2110,14 @@
 
 static int nvme_pr_clear(struct block_device *bdev, u64 key)
 {
-	u32 cdw10 = 1 | (key ? 1 << 3 : 0);
+	u32 cdw10 = 1 | (key ? 0 : 1 << 3);
 
-	return nvme_pr_command(bdev, cdw10, key, 0, nvme_cmd_resv_register);
+	return nvme_pr_command(bdev, cdw10, key, 0, nvme_cmd_resv_release);
 }
 
 static int nvme_pr_release(struct block_device *bdev, u64 key, enum pr_type type)
 {
-	u32 cdw10 = nvme_pr_type(type) << 8 | (key ? 1 << 3 : 0);
+	u32 cdw10 = nvme_pr_type(type) << 8 | (key ? 0 : 1 << 3);
 
 	return nvme_pr_command(bdev, cdw10, key, 0, nvme_cmd_resv_release);
 }
@@ -2095,6 +2165,7 @@
 static const struct block_device_operations nvme_bdev_ops = {
 	.owner		= THIS_MODULE,
 	.ioctl		= nvme_ioctl,
+	.compat_ioctl	= blkdev_compat_ptr_ioctl,
 	.open		= nvme_open,
 	.release	= nvme_release,
 	.getgeo		= nvme_getgeo,
@@ -2468,6 +2539,34 @@
 		.vid = 0x14a4,
 		.fr = "22301111",
 		.quirks = NVME_QUIRK_SIMPLE_SUSPEND,
+	},
+	{
+		/*
+		 * This Kioxia CD6-V Series / HPE PE8030 device times out and
+		 * aborts I/O during any load, but more easily reproducible
+		 * with discards (fstrim).
+		 *
+		 * The device is left in a state where it is also not possible
+		 * to use "nvme set-feature" to disable APST, but booting with
+		 * nvme_core.default_ps_max_latency=0 works.
+		 */
+		.vid = 0x1e0f,
+		.mn = "KCD6XVUL6T40",
+		.quirks = NVME_QUIRK_NO_APST,
+	},
+	{
+		/*
+		 * The external Samsung X5 SSD fails initialization without a
+		 * delay before checking if it is ready and has a whole set of
+		 * other problems.  To make this even more interesting, it
+		 * shares the PCI ID with internal Samsung 970 Evo Plus that
+		 * does not need or want these quirks.
+		 */
+		.vid = 0x144d,
+		.mn = "Samsung Portable SSD X5",
+		.quirks = NVME_QUIRK_DELAY_BEFORE_CHK_RDY |
+			  NVME_QUIRK_NO_DEEPEST_PS |
+			  NVME_QUIRK_IGNORE_DEV_SUBNQN,
 	}
 };
 
@@ -2687,7 +2786,6 @@
 	nvme_init_subnqn(subsys, ctrl, id);
 	memcpy(subsys->serial, id->sn, sizeof(subsys->serial));
 	memcpy(subsys->model, id->mn, sizeof(subsys->model));
-	memcpy(subsys->firmware_rev, id->fr, sizeof(subsys->firmware_rev));
 	subsys->vendor_id = le16_to_cpu(id->vid);
 	subsys->cmic = id->cmic;
 	subsys->awupf = le16_to_cpu(id->awupf);
@@ -2767,7 +2865,7 @@
 static int nvme_get_effects_log(struct nvme_ctrl *ctrl, u8 csi,
 				struct nvme_effects_log **log)
 {
-	struct nvme_effects_log	*cel = xa_load(&ctrl->cels, csi);
+	struct nvme_effects_log *old, *cel = xa_load(&ctrl->cels, csi);
 	int ret;
 
 	if (cel)
@@ -2784,7 +2882,11 @@
 		return ret;
 	}
 
-	xa_store(&ctrl->cels, csi, cel, GFP_KERNEL);
+	old = xa_store(&ctrl->cels, csi, cel, GFP_KERNEL);
+	if (xa_is_err(old)) {
+		kfree(cel);
+		return xa_err(old);
+	}
 out:
 	*log = cel;
 	return 0;
@@ -2830,7 +2932,7 @@
 
 	id = kzalloc(sizeof(*id), GFP_KERNEL);
 	if (!id)
-		return 0;
+		return -ENOMEM;
 
 	c.identify.opcode = nvme_admin_identify;
 	c.identify.cns = NVME_ID_CNS_CS_CTRL;
@@ -2877,10 +2979,6 @@
 	if (!ctrl->identified) {
 		unsigned int i;
 
-		ret = nvme_init_subsystem(ctrl, id);
-		if (ret)
-			goto out_free;
-
 		/*
 		 * Check for quirks.  Quirk can depend on firmware version,
 		 * so, in principle, the set of quirks present can change
@@ -2893,7 +2991,13 @@
 			if (quirk_matches(id, &core_quirks[i]))
 				ctrl->quirks |= core_quirks[i].quirks;
 		}
+
+		ret = nvme_init_subsystem(ctrl, id);
+		if (ret)
+			goto out_free;
 	}
+	memcpy(ctrl->subsys->firmware_rev, id->fr,
+	       sizeof(ctrl->subsys->firmware_rev));
 
 	if (force_apst && (ctrl->quirks & NVME_QUIRK_NO_DEEPEST_PS)) {
 		dev_warn(ctrl->device, "forcibly allowing all power states due to nvme_core.force_apst -- use at your own risk\n");
@@ -2926,6 +3030,9 @@
 	ctrl->max_namespaces = le32_to_cpu(id->mnan);
 	ctrl->ctratt = le32_to_cpu(id->ctratt);
 
+	ctrl->cntrltype = id->cntrltype;
+	ctrl->dctype = id->dctype;
+
 	if (id->rtd3e) {
 		/* us -> s */
 		u32 transition_time = le32_to_cpu(id->rtd3e) / USEC_PER_SEC;
@@ -3025,10 +3132,6 @@
 	if (ret)
 		return ret;
 
-	ret = nvme_init_non_mdts_limits(ctrl);
-	if (ret < 0)
-		return ret;
-
 	ret = nvme_configure_apst(ctrl);
 	if (ret < 0)
 		return ret;
@@ -3046,8 +3149,12 @@
 		return ret;
 
 	if (!ctrl->identified && !nvme_discovery_ctrl(ctrl)) {
+		/*
+		 * Do not return errors unless we are in a controller reset,
+		 * the controller works perfectly fine without hwmon.
+		 */
 		ret = nvme_hwmon_init(ctrl);
-		if (ret < 0)
+		if (ret == -EINTR)
 			return ret;
 	}
 
@@ -3179,8 +3286,8 @@
 	 * we have no UUID set
 	 */
 	if (uuid_is_null(&ids->uuid)) {
-		printk_ratelimited(KERN_WARNING
-				   "No UUID available providing old NGUID\n");
+		dev_warn_ratelimited(dev,
+			"No UUID available providing old NGUID\n");
 		return sysfs_emit(buf, "%pU\n", ids->nguid);
 	}
 	return sysfs_emit(buf, "%pU\n", &ids->uuid);
@@ -3459,6 +3566,40 @@
 static DEVICE_ATTR(fast_io_fail_tmo, S_IRUGO | S_IWUSR,
 	nvme_ctrl_fast_io_fail_tmo_show, nvme_ctrl_fast_io_fail_tmo_store);
 
+static ssize_t cntrltype_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	static const char * const type[] = {
+		[NVME_CTRL_IO] = "io\n",
+		[NVME_CTRL_DISC] = "discovery\n",
+		[NVME_CTRL_ADMIN] = "admin\n",
+	};
+	struct nvme_ctrl *ctrl = dev_get_drvdata(dev);
+
+	if (ctrl->cntrltype > NVME_CTRL_ADMIN || !type[ctrl->cntrltype])
+		return sysfs_emit(buf, "reserved\n");
+
+	return sysfs_emit(buf, type[ctrl->cntrltype]);
+}
+static DEVICE_ATTR_RO(cntrltype);
+
+static ssize_t dctype_show(struct device *dev,
+			   struct device_attribute *attr, char *buf)
+{
+	static const char * const type[] = {
+		[NVME_DCTYPE_NOT_REPORTED] = "none\n",
+		[NVME_DCTYPE_DDC] = "ddc\n",
+		[NVME_DCTYPE_CDC] = "cdc\n",
+	};
+	struct nvme_ctrl *ctrl = dev_get_drvdata(dev);
+
+	if (ctrl->dctype > NVME_DCTYPE_CDC || !type[ctrl->dctype])
+		return sysfs_emit(buf, "reserved\n");
+
+	return sysfs_emit(buf, type[ctrl->dctype]);
+}
+static DEVICE_ATTR_RO(dctype);
+
 static struct attribute *nvme_dev_attrs[] = {
 	&dev_attr_reset_controller.attr,
 	&dev_attr_rescan_controller.attr,
@@ -3480,6 +3621,8 @@
 	&dev_attr_reconnect_delay.attr,
 	&dev_attr_fast_io_fail_tmo.attr,
 	&dev_attr_kato.attr,
+	&dev_attr_cntrltype.attr,
+	&dev_attr_dctype.attr,
 	NULL
 };
 
@@ -3517,15 +3660,20 @@
 	NULL,
 };
 
-static struct nvme_ns_head *nvme_find_ns_head(struct nvme_subsystem *subsys,
+static struct nvme_ns_head *nvme_find_ns_head(struct nvme_ctrl *ctrl,
 		unsigned nsid)
 {
 	struct nvme_ns_head *h;
 
-	lockdep_assert_held(&subsys->lock);
+	lockdep_assert_held(&ctrl->subsys->lock);
 
-	list_for_each_entry(h, &subsys->nsheads, entry) {
-		if (h->ns_id != nsid)
+	list_for_each_entry(h, &ctrl->subsys->nsheads, entry) {
+		/*
+		 * Private namespaces can share NSIDs under some conditions.
+		 * In that case we can't use the same ns_head for namespaces
+		 * with the same NSID.
+		 */
+		if (h->ns_id != nsid || !nvme_is_unique_nsid(ctrl, h))
 			continue;
 		if (!list_empty(&h->list) && nvme_tryget_ns_head(h))
 			return h;
@@ -3534,16 +3682,24 @@
 	return NULL;
 }
 
-static int __nvme_check_ids(struct nvme_subsystem *subsys,
-		struct nvme_ns_head *new)
+static int nvme_subsys_check_duplicate_ids(struct nvme_subsystem *subsys,
+		struct nvme_ns_ids *ids)
 {
+	bool has_uuid = !uuid_is_null(&ids->uuid);
+	bool has_nguid = memchr_inv(ids->nguid, 0, sizeof(ids->nguid));
+	bool has_eui64 = memchr_inv(ids->eui64, 0, sizeof(ids->eui64));
 	struct nvme_ns_head *h;
 
 	lockdep_assert_held(&subsys->lock);
 
 	list_for_each_entry(h, &subsys->nsheads, entry) {
-		if (nvme_ns_ids_valid(&new->ids) &&
-		    nvme_ns_ids_equal(&new->ids, &h->ids))
+		if (has_uuid && uuid_equal(&ids->uuid, &h->ids.uuid))
+			return -EINVAL;
+		if (has_nguid &&
+		    memcmp(&ids->nguid, &h->ids.nguid, sizeof(ids->nguid)) == 0)
+			return -EINVAL;
+		if (has_eui64 &&
+		    memcmp(&ids->eui64, &h->ids.eui64, sizeof(ids->eui64)) == 0)
 			return -EINVAL;
 	}
 
@@ -3616,7 +3772,7 @@
 }
 
 static struct nvme_ns_head *nvme_alloc_ns_head(struct nvme_ctrl *ctrl,
-		unsigned nsid, struct nvme_ns_ids *ids)
+		unsigned nsid, struct nvme_ns_ids *ids, bool is_shared)
 {
 	struct nvme_ns_head *head;
 	size_t size = sizeof(*head);
@@ -3640,15 +3796,9 @@
 	head->subsys = ctrl->subsys;
 	head->ns_id = nsid;
 	head->ids = *ids;
+	head->shared = is_shared;
 	kref_init(&head->ref);
 
-	ret = __nvme_check_ids(ctrl->subsys, head);
-	if (ret) {
-		dev_err(ctrl->device,
-			"duplicate IDs for nsid %d\n", nsid);
-		goto out_cleanup_srcu;
-	}
-
 	if (head->ids.csi) {
 		ret = nvme_get_effects_log(ctrl, head->ids.csi, &head->effects);
 		if (ret)
@@ -3685,14 +3835,19 @@
 	int ret = 0;
 
 	mutex_lock(&ctrl->subsys->lock);
-	head = nvme_find_ns_head(ctrl->subsys, nsid);
+	head = nvme_find_ns_head(ctrl, nsid);
 	if (!head) {
-		head = nvme_alloc_ns_head(ctrl, nsid, ids);
+		ret = nvme_subsys_check_duplicate_ids(ctrl->subsys, ids);
+		if (ret) {
+			dev_err(ctrl->device,
+				"duplicate IDs for nsid %d\n", nsid);
+			goto out_unlock;
+		}
+		head = nvme_alloc_ns_head(ctrl, nsid, ids, is_shared);
 		if (IS_ERR(head)) {
 			ret = PTR_ERR(head);
 			goto out_unlock;
 		}
-		head->shared = is_shared;
 	} else {
 		ret = -EINVAL;
 		if (!is_shared || !head->shared) {
@@ -3862,7 +4017,7 @@
 	mutex_unlock(&ns->ctrl->subsys->lock);
 
 	/* guarantee not available in head->list */
-	synchronize_rcu();
+	synchronize_srcu(&ns->head->srcu);
 
 	/* wait for concurrent submissions */
 	if (nvme_mpath_clear_current_path(ns))
@@ -4076,11 +4231,26 @@
 {
 	struct nvme_ctrl *ctrl =
 		container_of(work, struct nvme_ctrl, scan_work);
+	int ret;
 
 	/* No tagset on a live ctrl means IO queues could not created */
 	if (ctrl->state != NVME_CTRL_LIVE || !ctrl->tagset)
 		return;
 
+	/*
+	 * Identify controller limits can change at controller reset due to
+	 * new firmware download, even though it is not common we cannot ignore
+	 * such scenario. Controller's non-mdts limits are reported in the unit
+	 * of logical blocks that is dependent on the format of attached
+	 * namespace. Hence re-read the limits at the time of ns allocation.
+	 */
+	ret = nvme_init_non_mdts_limits(ctrl);
+	if (ret < 0) {
+		dev_warn(ctrl->device,
+			"reading non-mdts-limits failed: %d\n", ret);
+		return;
+	}
+
 	if (test_and_clear_bit(NVME_AER_NOTICE_NS_CHANGED, &ctrl->events)) {
 		dev_info(ctrl->device, "rescanning namespaces.\n");
 		nvme_clear_changed_ns_log(ctrl);
@@ -4165,6 +4335,13 @@
 	return ret;
 }
 
+static void nvme_change_uevent(struct nvme_ctrl *ctrl, char *envdata)
+{
+	char *envp[2] = { envdata, NULL };
+
+	kobject_uevent_env(&ctrl->device->kobj, KOBJ_CHANGE, envp);
+}
+
 static void nvme_aen_uevent(struct nvme_ctrl *ctrl)
 {
 	char *envp[2] = { NULL, NULL };
@@ -4187,7 +4364,14 @@
 		container_of(work, struct nvme_ctrl, async_event_work);
 
 	nvme_aen_uevent(ctrl);
-	ctrl->ops->submit_async_event(ctrl);
+
+	/*
+	 * The transport drivers must guarantee AER submission here is safe by
+	 * flushing ctrl async_event_work after changing the controller state
+	 * from LIVE and before freeing the admin queue.
+	*/
+	if (ctrl->state == NVME_CTRL_LIVE)
+		ctrl->ops->submit_async_event(ctrl);
 }
 
 static bool nvme_ctrl_pp_status(struct nvme_ctrl *ctrl)
@@ -4250,11 +4434,19 @@
 	nvme_get_fw_slot_info(ctrl);
 }
 
-static void nvme_handle_aen_notice(struct nvme_ctrl *ctrl, u32 result)
+static u32 nvme_aer_type(u32 result)
 {
-	u32 aer_notice_type = (result & 0xff00) >> 8;
+	return result & 0x7;
+}
 
-	trace_nvme_async_event(ctrl, aer_notice_type);
+static u32 nvme_aer_subtype(u32 result)
+{
+	return (result & 0xff00) >> 8;
+}
+
+static void nvme_handle_aen_notice(struct nvme_ctrl *ctrl, u32 result)
+{
+	u32 aer_notice_type = nvme_aer_subtype(result);
 
 	switch (aer_notice_type) {
 	case NVME_AER_NOTICE_NS_CHANGED:
@@ -4285,24 +4477,40 @@
 	}
 }
 
+static void nvme_handle_aer_persistent_error(struct nvme_ctrl *ctrl)
+{
+	dev_warn(ctrl->device, "resetting controller due to AER\n");
+	nvme_reset_ctrl(ctrl);
+}
+
 void nvme_complete_async_event(struct nvme_ctrl *ctrl, __le16 status,
 		volatile union nvme_result *res)
 {
 	u32 result = le32_to_cpu(res->u32);
-	u32 aer_type = result & 0x07;
+	u32 aer_type = nvme_aer_type(result);
+	u32 aer_subtype = nvme_aer_subtype(result);
 
 	if (le16_to_cpu(status) >> 1 != NVME_SC_SUCCESS)
 		return;
 
+	trace_nvme_async_event(ctrl, result);
 	switch (aer_type) {
 	case NVME_AER_NOTICE:
 		nvme_handle_aen_notice(ctrl, result);
 		break;
 	case NVME_AER_ERROR:
+		/*
+		 * For a persistent internal error, don't run async_event_work
+		 * to submit a new AER. The controller reset will do it.
+		 */
+		if (aer_subtype == NVME_AER_ERROR_PERSIST_INT_ERR) {
+			nvme_handle_aer_persistent_error(ctrl);
+			return;
+		}
+		fallthrough;
 	case NVME_AER_SMART:
 	case NVME_AER_CSS:
 	case NVME_AER_VS:
-		trace_nvme_async_event(ctrl, aer_type);
 		ctrl->aen_result = result;
 		break;
 	default:
@@ -4319,6 +4527,8 @@
 	nvme_stop_failfast_work(ctrl);
 	flush_work(&ctrl->async_event_work);
 	cancel_work_sync(&ctrl->fw_act_work);
+	if (ctrl->ops->stop_ctrl)
+		ctrl->ops->stop_ctrl(ctrl);
 }
 EXPORT_SYMBOL_GPL(nvme_stop_ctrl);
 
@@ -4331,7 +4541,10 @@
 	if (ctrl->queue_count > 1) {
 		nvme_queue_scan(ctrl);
 		nvme_start_queues(ctrl);
+		nvme_mpath_update(ctrl);
 	}
+
+	nvme_change_uevent(ctrl, "NVME_EVENT=connected");
 }
 EXPORT_SYMBOL_GPL(nvme_start_ctrl);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/fabrics.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/fabrics.c
@@ -271,6 +271,12 @@
 {
 	int err_sctype = errval & ~NVME_SC_DNR;
 
+	if (errval < 0) {
+		dev_err(ctrl->device,
+			"Connect command failed, errno: %d\n", errval);
+		return;
+	}
+
 	switch (err_sctype) {
 	case (NVME_SC_CONNECT_INVALID_PARAM):
 		if (offset >> 16) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/fabrics.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/fabrics.h
@@ -169,6 +169,7 @@
 			struct nvmf_ctrl_options *opts)
 {
 	if (ctrl->state == NVME_CTRL_DELETING ||
+	    ctrl->state == NVME_CTRL_DELETING_NOIO ||
 	    ctrl->state == NVME_CTRL_DEAD ||
 	    strcmp(opts->subsysnqn, ctrl->opts->subsysnqn) ||
 	    strcmp(opts->host->nqn, ctrl->opts->host->nqn) ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/fc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/fc.c
@@ -220,11 +220,6 @@
 static DEFINE_IDA(nvme_fc_local_port_cnt);
 static DEFINE_IDA(nvme_fc_ctrl_cnt);
 
-static struct workqueue_struct *nvme_fc_wq;
-
-static bool nvme_fc_waiting_to_unload;
-static DECLARE_COMPLETION(nvme_fc_unload_proceed);
-
 /*
  * These items are short-term. They will eventually be moved into
  * a generic FC class. See comments in module init.
@@ -254,8 +249,6 @@
 	/* remove from transport list */
 	spin_lock_irqsave(&nvme_fc_lock, flags);
 	list_del(&lport->port_list);
-	if (nvme_fc_waiting_to_unload && list_empty(&nvme_fc_lport_list))
-		complete(&nvme_fc_unload_proceed);
 	spin_unlock_irqrestore(&nvme_fc_lock, flags);
 
 	ida_simple_remove(&nvme_fc_local_port_cnt, lport->localport.port_num);
@@ -3554,8 +3547,7 @@
 	list_add_tail(&ctrl->ctrl_list, &rport->ctrl_list);
 	spin_unlock_irqrestore(&rport->lock, flags);
 
-	if (!nvme_change_ctrl_state(&ctrl->ctrl, NVME_CTRL_RESETTING) ||
-	    !nvme_change_ctrl_state(&ctrl->ctrl, NVME_CTRL_CONNECTING)) {
+	if (!nvme_change_ctrl_state(&ctrl->ctrl, NVME_CTRL_CONNECTING)) {
 		dev_err(ctrl->ctrl.device,
 			"NVME-FC{%d}: failed to init ctrl state\n", ctrl->cnum);
 		goto fail_ctrl;
@@ -3904,10 +3896,6 @@
 {
 	int ret;
 
-	nvme_fc_wq = alloc_workqueue("nvme_fc_wq", WQ_MEM_RECLAIM, 0);
-	if (!nvme_fc_wq)
-		return -ENOMEM;
-
 	/*
 	 * NOTE:
 	 * It is expected that in the future the kernel will combine
@@ -3925,7 +3913,7 @@
 	ret = class_register(&fc_class);
 	if (ret) {
 		pr_err("couldn't register class fc\n");
-		goto out_destroy_wq;
+		return ret;
 	}
 
 	/*
@@ -3949,8 +3937,6 @@
 	device_destroy(&fc_class, MKDEV(0, 0));
 out_destroy_class:
 	class_unregister(&fc_class);
-out_destroy_wq:
-	destroy_workqueue(nvme_fc_wq);
 
 	return ret;
 }
@@ -3970,45 +3956,23 @@
 	spin_unlock(&rport->lock);
 }
 
-static void
-nvme_fc_cleanup_for_unload(void)
+static void __exit nvme_fc_exit_module(void)
 {
 	struct nvme_fc_lport *lport;
 	struct nvme_fc_rport *rport;
-
-	list_for_each_entry(lport, &nvme_fc_lport_list, port_list) {
-		list_for_each_entry(rport, &lport->endp_list, endp_list) {
-			nvme_fc_delete_controllers(rport);
-		}
-	}
-}
-
-static void __exit nvme_fc_exit_module(void)
-{
 	unsigned long flags;
-	bool need_cleanup = false;
 
 	spin_lock_irqsave(&nvme_fc_lock, flags);
-	nvme_fc_waiting_to_unload = true;
-	if (!list_empty(&nvme_fc_lport_list)) {
-		need_cleanup = true;
-		nvme_fc_cleanup_for_unload();
-	}
+	list_for_each_entry(lport, &nvme_fc_lport_list, port_list)
+		list_for_each_entry(rport, &lport->endp_list, endp_list)
+			nvme_fc_delete_controllers(rport);
 	spin_unlock_irqrestore(&nvme_fc_lock, flags);
-	if (need_cleanup) {
-		pr_info("%s: waiting for ctlr deletes\n", __func__);
-		wait_for_completion(&nvme_fc_unload_proceed);
-		pr_info("%s: ctrl deletes complete\n", __func__);
-	}
+	flush_workqueue(nvme_delete_wq);
 
 	nvmf_unregister_transport(&nvme_fc_transport);
 
-	ida_destroy(&nvme_fc_local_port_cnt);
-	ida_destroy(&nvme_fc_ctrl_cnt);
-
 	device_destroy(&fc_class, MKDEV(0, 0));
 	class_unregister(&fc_class);
-	destroy_workqueue(nvme_fc_wq);
 }
 
 module_init(nvme_fc_init_module);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/hwmon.c
@@ -12,7 +12,7 @@
 
 struct nvme_hwmon_data {
 	struct nvme_ctrl *ctrl;
-	struct nvme_smart_log log;
+	struct nvme_smart_log *log;
 	struct mutex read_lock;
 };
 
@@ -60,14 +60,14 @@
 static int nvme_hwmon_get_smart_log(struct nvme_hwmon_data *data)
 {
 	return nvme_get_log(data->ctrl, NVME_NSID_ALL, NVME_LOG_SMART, 0,
-			   NVME_CSI_NVM, &data->log, sizeof(data->log), 0);
+			   NVME_CSI_NVM, data->log, sizeof(*data->log), 0);
 }
 
 static int nvme_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
 			   u32 attr, int channel, long *val)
 {
 	struct nvme_hwmon_data *data = dev_get_drvdata(dev);
-	struct nvme_smart_log *log = &data->log;
+	struct nvme_smart_log *log = data->log;
 	int temp;
 	int err;
 
@@ -163,7 +163,9 @@
 	case hwmon_temp_max:
 	case hwmon_temp_min:
 		if ((!channel && data->ctrl->wctemp) ||
-		    (channel && data->log.temp_sensor[channel - 1])) {
+		    (channel && data->log->temp_sensor[channel - 1] &&
+		     !(data->ctrl->quirks &
+		       NVME_QUIRK_NO_SECONDARY_TEMP_THRESH))) {
 			if (data->ctrl->quirks &
 			    NVME_QUIRK_NO_TEMP_THRESH_CHANGE)
 				return 0444;
@@ -176,7 +178,7 @@
 		break;
 	case hwmon_temp_input:
 	case hwmon_temp_label:
-		if (!channel || data->log.temp_sensor[channel - 1])
+		if (!channel || data->log->temp_sensor[channel - 1])
 			return 0444;
 		break;
 	default:
@@ -230,7 +232,13 @@
 
 	data = kzalloc(sizeof(*data), GFP_KERNEL);
 	if (!data)
-		return 0;
+		return -ENOMEM;
+
+	data->log = kzalloc(sizeof(*data->log), GFP_KERNEL);
+	if (!data->log) {
+		err = -ENOMEM;
+		goto err_free_data;
+	}
 
 	data->ctrl = ctrl;
 	mutex_init(&data->read_lock);
@@ -238,8 +246,7 @@
 	err = nvme_hwmon_get_smart_log(data);
 	if (err) {
 		dev_warn(dev, "Failed to read smart log (error %d)\n", err);
-		kfree(data);
-		return err;
+		goto err_free_log;
 	}
 
 	hwmon = hwmon_device_register_with_info(dev, "nvme",
@@ -247,11 +254,17 @@
 						NULL);
 	if (IS_ERR(hwmon)) {
 		dev_warn(dev, "Failed to instantiate hwmon device\n");
-		kfree(data);
-		return PTR_ERR(hwmon);
+		err = PTR_ERR(hwmon);
+		goto err_free_log;
 	}
 	ctrl->hwmon_device = hwmon;
 	return 0;
+
+err_free_log:
+	kfree(data->log);
+err_free_data:
+	kfree(data);
+	return err;
 }
 
 void nvme_hwmon_exit(struct nvme_ctrl *ctrl)
@@ -262,6 +275,7 @@
 
 		hwmon_device_unregister(ctrl->hwmon_device);
 		ctrl->hwmon_device = NULL;
+		kfree(data->log);
 		kfree(data);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/ioctl.c
@@ -61,11 +61,16 @@
 	bool write = nvme_is_write(cmd);
 	struct nvme_ns *ns = q->queuedata;
 	struct block_device *bdev = ns ? ns->disk->part0 : NULL;
+	bool supports_metadata = bdev && blk_get_integrity(bdev->bd_disk);
+	bool has_metadata = meta_buffer && meta_len;
 	struct request *req;
 	struct bio *bio = NULL;
 	void *meta = NULL;
 	int ret;
 
+	if (has_metadata && !supports_metadata)
+			return -EINVAL;
+
 	req = nvme_alloc_request(q, cmd, 0);
 	if (IS_ERR(req))
 		return PTR_ERR(req);
@@ -82,7 +87,7 @@
 		bio = req->bio;
 		if (bdev)
 			bio_set_dev(bio, bdev);
-		if (bdev && meta_buffer && meta_len) {
+		if (has_metadata) {
 			meta = nvme_add_user_metadata(bio, meta_buffer, meta_len,
 					meta_seed, write);
 			if (IS_ERR(meta)) {
@@ -178,8 +183,7 @@
 {
 	if (ns && nsid != ns->head->ns_id) {
 		dev_err(ctrl->device,
-			"%s: nsid (%u) in cmd does not match nsid (%u)"
-			"of namespace\n",
+			"%s: nsid (%u) in cmd does not match nsid (%u) of namespace\n",
 			current->comm, nsid, ns->head->ns_id);
 		return false;
 	}
@@ -484,11 +488,17 @@
 	case NVME_IOCTL_IO_CMD:
 		return nvme_dev_user_cmd(ctrl, argp);
 	case NVME_IOCTL_RESET:
+		if (!capable(CAP_SYS_ADMIN))
+			return -EACCES;
 		dev_warn(ctrl->device, "resetting controller\n");
 		return nvme_reset_ctrl_sync(ctrl);
 	case NVME_IOCTL_SUBSYS_RESET:
+		if (!capable(CAP_SYS_ADMIN))
+			return -EACCES;
 		return nvme_reset_subsystem(ctrl);
 	case NVME_IOCTL_RESCAN:
+		if (!capable(CAP_SYS_ADMIN))
+			return -EACCES;
 		nvme_queue_scan(ctrl);
 		return 0;
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/multipath.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/multipath.c
@@ -138,13 +138,12 @@
 {
 	struct nvme_ns *ns;
 
-	mutex_lock(&ctrl->scan_lock);
 	down_read(&ctrl->namespaces_rwsem);
-	list_for_each_entry(ns, &ctrl->namespaces, list)
-		if (nvme_mpath_clear_current_path(ns))
-			kblockd_schedule_work(&ns->head->requeue_work);
+	list_for_each_entry(ns, &ctrl->namespaces, list) {
+		nvme_mpath_clear_current_path(ns);
+		kblockd_schedule_work(&ns->head->requeue_work);
+	}
 	up_read(&ctrl->namespaces_rwsem);
-	mutex_unlock(&ctrl->scan_lock);
 }
 
 void nvme_mpath_revalidate_paths(struct nvme_ns *ns)
@@ -152,14 +151,18 @@
 	struct nvme_ns_head *head = ns->head;
 	sector_t capacity = get_capacity(head->disk);
 	int node;
+	int srcu_idx;
 
+	srcu_idx = srcu_read_lock(&head->srcu);
 	list_for_each_entry_rcu(ns, &head->list, siblings) {
 		if (capacity != get_capacity(ns->disk))
 			clear_bit(NVME_NS_READY, &ns->flags);
 	}
+	srcu_read_unlock(&head->srcu, srcu_idx);
 
 	for_each_node(node)
 		rcu_assign_pointer(head->current_path[node], NULL);
+	kblockd_schedule_work(&head->requeue_work);
 }
 
 static bool nvme_path_is_disabled(struct nvme_ns *ns)
@@ -187,7 +190,8 @@
 		if (nvme_path_is_disabled(ns))
 			continue;
 
-		if (READ_ONCE(head->subsys->iopolicy) == NVME_IOPOLICY_NUMA)
+		if (ns->ctrl->numa_node != NUMA_NO_NODE &&
+		    READ_ONCE(head->subsys->iopolicy) == NVME_IOPOLICY_NUMA)
 			distance = node_distance(node, ns->ctrl->numa_node);
 		else
 			distance = LOCAL_DISTANCE;
@@ -326,6 +330,8 @@
 	 * pool from the original queue to allocate the bvecs from.
 	 */
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
 	srcu_idx = srcu_read_lock(&head->srcu);
 	ns = nvme_find_path(head);
@@ -389,6 +395,7 @@
 	.open		= nvme_ns_head_open,
 	.release	= nvme_ns_head_release,
 	.ioctl		= nvme_ns_head_ioctl,
+	.compat_ioctl	= blkdev_compat_ptr_ioctl,
 	.getgeo		= nvme_getgeo,
 	.report_zones	= nvme_ns_head_report_zones,
 	.pr_ops		= &nvme_pr_ops,
@@ -463,10 +470,11 @@
 
 	/*
 	 * Add a multipath node if the subsystems supports multiple controllers.
-	 * We also do this for private namespaces as the namespace sharing data could
-	 * change after a rescan.
+	 * We also do this for private namespaces as the namespace sharing flag
+	 * could change after a rescan.
 	 */
-	if (!(ctrl->subsys->cmic & NVME_CTRL_CMIC_MULTI_CTRL) || !multipath)
+	if (!(ctrl->subsys->cmic & NVME_CTRL_CMIC_MULTI_CTRL) ||
+	    !nvme_is_unique_nsid(ctrl, head) || !multipath)
 		return 0;
 
 	head->disk = blk_alloc_disk(ctrl->numa_node);
@@ -509,7 +517,7 @@
 		int node, srcu_idx;
 
 		srcu_idx = srcu_read_lock(&head->srcu);
-		for_each_node(node)
+		for_each_online_node(node)
 			__nvme_find_path(head, node);
 		srcu_read_unlock(&head->srcu, srcu_idx);
 	}
@@ -574,8 +582,17 @@
 	ns->ana_grpid = le32_to_cpu(desc->grpid);
 	ns->ana_state = desc->state;
 	clear_bit(NVME_NS_ANA_PENDING, &ns->flags);
-
-	if (nvme_state_is_live(ns->ana_state))
+	/*
+	 * nvme_mpath_set_live() will trigger I/O to the multipath path device
+	 * and in turn to this path device.  However we cannot accept this I/O
+	 * if the controller is not live.  This may deadlock if called from
+	 * nvme_mpath_init_identify() and the ctrl will never complete
+	 * initialization, preventing I/O from completing.  For this case we
+	 * will reprocess the ANA log page in nvme_mpath_update() once the
+	 * controller is ready.
+	 */
+	if (nvme_state_is_live(ns->ana_state) &&
+	    ns->ctrl->state == NVME_CTRL_LIVE)
 		nvme_mpath_set_live(ns);
 }
 
@@ -662,6 +679,18 @@
 	nvme_read_ana_log(ctrl);
 }
 
+void nvme_mpath_update(struct nvme_ctrl *ctrl)
+{
+	u32 nr_change_groups = 0;
+
+	if (!ctrl->ana_log_buf)
+		return;
+
+	mutex_lock(&ctrl->ana_lock);
+	nvme_parse_ana_log(ctrl, &nr_change_groups, nvme_update_ana_state);
+	mutex_unlock(&ctrl->ana_lock);
+}
+
 static void nvme_anatt_timeout(struct timer_list *t)
 {
 	struct nvme_ctrl *ctrl = from_timer(ctrl, t, anatt_timer);
@@ -793,7 +822,6 @@
 {
 	if (!head->disk)
 		return;
-	blk_set_queue_dying(head->disk->queue);
 	/* make sure all pending bios are cleaned up */
 	kblockd_schedule_work(&head->requeue_work);
 	flush_work(&head->requeue_work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/nvme.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/nvme.h
@@ -87,6 +87,11 @@
 	NVME_QUIRK_NO_DEEPEST_PS		= (1 << 5),
 
 	/*
+	 *  Problems seen with concurrent commands
+	 */
+	NVME_QUIRK_QDEPTH_ONE			= (1 << 6),
+
+	/*
 	 * Set MEDIUM priority on SQ creation
 	 */
 	NVME_QUIRK_MEDIUM_PRIO_SQ		= (1 << 7),
@@ -144,6 +149,21 @@
 	 * encoding the generation sequence number.
 	 */
 	NVME_QUIRK_SKIP_CID_GEN			= (1 << 17),
+
+	/*
+	 * Reports garbage in the namespace identifiers (eui64, nguid, uuid).
+	 */
+	NVME_QUIRK_BOGUS_NID			= (1 << 18),
+
+	/*
+	 * No temperature thresholds for channels other than 0 (Composite).
+	 */
+	NVME_QUIRK_NO_SECONDARY_TEMP_THRESH	= (1 << 19),
+
+	/*
+	 * Disables simple suspend/resume path.
+	 */
+	NVME_QUIRK_FORCE_NO_SIMPLE_SUSPEND	= (1 << 20),
 };
 
 /*
@@ -348,8 +368,16 @@
 	unsigned long discard_page_busy;
 
 	struct nvme_fault_inject fault_inject;
+
+	enum nvme_ctrl_type cntrltype;
+	enum nvme_dctype dctype;
 };
 
+static inline enum nvme_ctrl_state nvme_ctrl_state(struct nvme_ctrl *ctrl)
+{
+	return READ_ONCE(ctrl->state);
+}
+
 enum nvme_iopolicy {
 	NVME_IOPOLICY_NUMA,
 	NVME_IOPOLICY_RR,
@@ -490,6 +518,7 @@
 	void (*free_ctrl)(struct nvme_ctrl *ctrl);
 	void (*submit_async_event)(struct nvme_ctrl *ctrl);
 	void (*delete_ctrl)(struct nvme_ctrl *ctrl);
+	void (*stop_ctrl)(struct nvme_ctrl *ctrl);
 	int (*get_address)(struct nvme_ctrl *ctrl, char *buf, int size);
 };
 
@@ -552,11 +581,23 @@
 static inline void nvme_should_fail(struct request *req) {}
 #endif
 
+bool nvme_wait_reset(struct nvme_ctrl *ctrl);
+int nvme_try_sched_reset(struct nvme_ctrl *ctrl);
+
 static inline int nvme_reset_subsystem(struct nvme_ctrl *ctrl)
 {
+	int ret;
+
 	if (!ctrl->subsystem)
 		return -ENOTTY;
-	return ctrl->ops->reg_write32(ctrl, NVME_REG_NSSR, 0x4E564D65);
+	if (!nvme_wait_reset(ctrl))
+		return -EBUSY;
+
+	ret = ctrl->ops->reg_write32(ctrl, NVME_REG_NSSR, 0x4E564D65);
+	if (ret)
+		return ret;
+
+	return nvme_try_sched_reset(ctrl);
 }
 
 /*
@@ -644,7 +685,6 @@
 void nvme_cancel_admin_tagset(struct nvme_ctrl *ctrl);
 bool nvme_change_ctrl_state(struct nvme_ctrl *ctrl,
 		enum nvme_ctrl_state new_state);
-bool nvme_wait_reset(struct nvme_ctrl *ctrl);
 int nvme_disable_ctrl(struct nvme_ctrl *ctrl);
 int nvme_enable_ctrl(struct nvme_ctrl *ctrl);
 int nvme_shutdown_ctrl(struct nvme_ctrl *ctrl);
@@ -693,6 +733,25 @@
 		return true;
 	return __nvme_check_ready(ctrl, rq, queue_live);
 }
+
+/*
+ * NSID shall be unique for all shared namespaces, or if at least one of the
+ * following conditions is met:
+ *   1. Namespace Management is supported by the controller
+ *   2. ANA is supported by the controller
+ *   3. NVM Set are supported by the controller
+ *
+ * In other case, private namespace are not required to report a unique NSID.
+ */
+static inline bool nvme_is_unique_nsid(struct nvme_ctrl *ctrl,
+		struct nvme_ns_head *head)
+{
+	return head->shared ||
+		(ctrl->oacs & NVME_CTRL_OACS_NS_MNGT_SUPP) ||
+		(ctrl->subsys->cmic & NVME_CTRL_CMIC_ANA) ||
+		(ctrl->ctratt & NVME_CTRL_CTRATT_NVM_SETS);
+}
+
 int nvme_submit_sync_cmd(struct request_queue *q, struct nvme_command *cmd,
 		void *buf, unsigned bufflen);
 int __nvme_submit_sync_cmd(struct request_queue *q, struct nvme_command *cmd,
@@ -709,7 +768,6 @@
 void nvme_stop_keep_alive(struct nvme_ctrl *ctrl);
 int nvme_reset_ctrl(struct nvme_ctrl *ctrl);
 int nvme_reset_ctrl_sync(struct nvme_ctrl *ctrl);
-int nvme_try_sched_reset(struct nvme_ctrl *ctrl);
 int nvme_delete_ctrl(struct nvme_ctrl *ctrl);
 void nvme_queue_scan(struct nvme_ctrl *ctrl);
 int nvme_get_log(struct nvme_ctrl *ctrl, u32 nsid, u8 log_page, u8 lsp, u8 csi,
@@ -752,6 +810,7 @@
 void nvme_mpath_remove_disk(struct nvme_ns_head *head);
 int nvme_mpath_init_identify(struct nvme_ctrl *ctrl, struct nvme_id_ctrl *id);
 void nvme_mpath_init_ctrl(struct nvme_ctrl *ctrl);
+void nvme_mpath_update(struct nvme_ctrl *ctrl);
 void nvme_mpath_uninit(struct nvme_ctrl *ctrl);
 void nvme_mpath_stop(struct nvme_ctrl *ctrl);
 bool nvme_mpath_clear_current_path(struct nvme_ns *ns);
@@ -763,7 +822,7 @@
 {
 	struct nvme_ns *ns = req->q->queuedata;
 
-	if (req->cmd_flags & REQ_NVME_MPATH)
+	if ((req->cmd_flags & REQ_NVME_MPATH) && req->bio)
 		trace_block_bio_complete(ns->head->disk->queue, req->bio);
 }
 
@@ -826,6 +885,9 @@
 "Please enable CONFIG_NVME_MULTIPATH for full support of multi-port devices.\n");
 	return 0;
 }
+static inline void nvme_mpath_update(struct nvme_ctrl *ctrl)
+{
+}
 static inline void nvme_mpath_uninit(struct nvme_ctrl *ctrl)
 {
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/pci.c
@@ -33,7 +33,7 @@
 #define SQ_SIZE(q)	((q)->q_depth << (q)->sqes)
 #define CQ_SIZE(q)	((q)->q_depth * sizeof(struct nvme_completion))
 
-#define SGES_PER_PAGE	(PAGE_SIZE / sizeof(struct nvme_sgl_desc))
+#define SGES_PER_PAGE	(NVME_CTRL_PAGE_SIZE / sizeof(struct nvme_sgl_desc))
 
 /*
  * These can be higher, but we need to ensure that any command doesn't
@@ -142,14 +142,15 @@
 	mempool_t *iod_mempool;
 
 	/* shadow doorbell buffer support: */
-	u32 *dbbuf_dbs;
+	__le32 *dbbuf_dbs;
 	dma_addr_t dbbuf_dbs_dma_addr;
-	u32 *dbbuf_eis;
+	__le32 *dbbuf_eis;
 	dma_addr_t dbbuf_eis_dma_addr;
 
 	/* host memory buffer support: */
 	u64 host_mem_size;
 	u32 nr_host_mem_descs;
+	u32 host_mem_descs_size;
 	dma_addr_t host_mem_descs_dma;
 	struct nvme_host_mem_buf_desc *host_mem_descs;
 	void **host_mem_desc_bufs;
@@ -208,10 +209,10 @@
 #define NVMEQ_SQ_CMB		1
 #define NVMEQ_DELETE_ERROR	2
 #define NVMEQ_POLLED		3
-	u32 *dbbuf_sq_db;
-	u32 *dbbuf_cq_db;
-	u32 *dbbuf_sq_ei;
-	u32 *dbbuf_cq_ei;
+	__le32 *dbbuf_sq_db;
+	__le32 *dbbuf_cq_db;
+	__le32 *dbbuf_sq_ei;
+	__le32 *dbbuf_cq_ei;
 	struct completion delete_done;
 };
 
@@ -224,7 +225,6 @@
 struct nvme_iod {
 	struct nvme_request req;
 	struct nvme_command cmd;
-	struct nvme_queue *nvmeq;
 	bool use_sgl;
 	int aborted;
 	int npages;		/* In the PRP list. 0 means small pool in use */
@@ -332,11 +332,11 @@
 }
 
 /* Update dbbuf and return true if an MMIO is required */
-static bool nvme_dbbuf_update_and_check_event(u16 value, u32 *dbbuf_db,
-					      volatile u32 *dbbuf_ei)
+static bool nvme_dbbuf_update_and_check_event(u16 value, __le32 *dbbuf_db,
+					      volatile __le32 *dbbuf_ei)
 {
 	if (dbbuf_db) {
-		u16 old_value;
+		u16 old_value, event_idx;
 
 		/*
 		 * Ensure that the queue is written before updating
@@ -344,8 +344,8 @@
 		 */
 		wmb();
 
-		old_value = *dbbuf_db;
-		*dbbuf_db = value;
+		old_value = le32_to_cpu(*dbbuf_db);
+		*dbbuf_db = cpu_to_le32(value);
 
 		/*
 		 * Ensure that the doorbell is updated before reading the event
@@ -355,7 +355,8 @@
 		 */
 		mb();
 
-		if (!nvme_dbbuf_need_event(*dbbuf_ei, value, old_value))
+		event_idx = le32_to_cpu(*dbbuf_ei);
+		if (!nvme_dbbuf_need_event(event_idx, value, old_value))
 			return false;
 	}
 
@@ -369,9 +370,9 @@
  */
 static int nvme_pci_npages_prp(void)
 {
-	unsigned nprps = DIV_ROUND_UP(NVME_MAX_KB_SZ + NVME_CTRL_PAGE_SIZE,
-				      NVME_CTRL_PAGE_SIZE);
-	return DIV_ROUND_UP(8 * nprps, PAGE_SIZE - 8);
+	unsigned max_bytes = (NVME_MAX_KB_SZ * 1024) + NVME_CTRL_PAGE_SIZE;
+	unsigned nprps = DIV_ROUND_UP(max_bytes, NVME_CTRL_PAGE_SIZE);
+	return DIV_ROUND_UP(8 * nprps, NVME_CTRL_PAGE_SIZE - 8);
 }
 
 /*
@@ -381,15 +382,7 @@
 static int nvme_pci_npages_sgl(void)
 {
 	return DIV_ROUND_UP(NVME_MAX_SEGS * sizeof(struct nvme_sgl_desc),
-			PAGE_SIZE);
-}
-
-static size_t nvme_pci_iod_alloc_size(void)
-{
-	size_t npages = max(nvme_pci_npages_prp(), nvme_pci_npages_sgl());
-
-	return sizeof(__le64 *) * npages +
-		sizeof(struct scatterlist) * NVME_MAX_SEGS;
+			NVME_CTRL_PAGE_SIZE);
 }
 
 static int nvme_admin_init_hctx(struct blk_mq_hw_ctx *hctx, void *data,
@@ -421,11 +414,6 @@
 {
 	struct nvme_dev *dev = set->driver_data;
 	struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
-	int queue_idx = (set == &dev->tagset) ? hctx_idx + 1 : 0;
-	struct nvme_queue *nvmeq = &dev->queues[queue_idx];
-
-	BUG_ON(!nvmeq);
-	iod->nvmeq = nvmeq;
 
 	nvme_req(req)->ctrl = &dev->ctrl;
 	nvme_req(req)->cmd = &iod->cmd;
@@ -492,22 +480,13 @@
 	nvmeq->last_sq_tail = nvmeq->sq_tail;
 }
 
-/**
- * nvme_submit_cmd() - Copy a command into a queue and ring the doorbell
- * @nvmeq: The queue to use
- * @cmd: The command to send
- * @write_sq: whether to write to the SQ doorbell
- */
-static void nvme_submit_cmd(struct nvme_queue *nvmeq, struct nvme_command *cmd,
-			    bool write_sq)
+static inline void nvme_sq_copy_cmd(struct nvme_queue *nvmeq,
+				    struct nvme_command *cmd)
 {
-	spin_lock(&nvmeq->sq_lock);
 	memcpy(nvmeq->sq_cmds + (nvmeq->sq_tail << nvmeq->sqes),
-	       cmd, sizeof(*cmd));
+		absolute_pointer(cmd), sizeof(*cmd));
 	if (++nvmeq->sq_tail == nvmeq->q_depth)
 		nvmeq->sq_tail = 0;
-	nvme_write_sq_db(nvmeq, write_sq);
-	spin_unlock(&nvmeq->sq_lock);
 }
 
 static void nvme_commit_rqs(struct blk_mq_hw_ctx *hctx)
@@ -528,7 +507,7 @@
 
 static inline bool nvme_pci_use_sgls(struct nvme_dev *dev, struct request *req)
 {
-	struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
+	struct nvme_queue *nvmeq = req->mq_hctx->driver_data;
 	int nseg = blk_rq_nr_phys_segments(req);
 	unsigned int avg_seg_size;
 
@@ -536,7 +515,7 @@
 
 	if (!nvme_ctrl_sgl_supported(&dev->ctrl))
 		return false;
-	if (!iod->nvmeq->qid)
+	if (!nvmeq->qid)
 		return false;
 	if (!sgl_threshold || avg_seg_size < sgl_threshold)
 		return false;
@@ -731,7 +710,7 @@
 		sge->length = cpu_to_le32(entries * sizeof(*sge));
 		sge->type = NVME_SGL_FMT_LAST_SEG_DESC << 4;
 	} else {
-		sge->length = cpu_to_le32(PAGE_SIZE);
+		sge->length = cpu_to_le32(NVME_CTRL_PAGE_SIZE);
 		sge->type = NVME_SGL_FMT_SEG_DESC << 4;
 	}
 }
@@ -814,6 +793,8 @@
 	cmnd->dptr.prp1 = cpu_to_le64(iod->first_dma);
 	if (bv->bv_len > first_prp_len)
 		cmnd->dptr.prp2 = cpu_to_le64(iod->first_dma + first_prp_len);
+	else
+		cmnd->dptr.prp2 = 0;
 	return BLK_STS_OK;
 }
 
@@ -843,14 +824,16 @@
 	int nr_mapped;
 
 	if (blk_rq_nr_phys_segments(req) == 1) {
+		struct nvme_queue *nvmeq = req->mq_hctx->driver_data;
 		struct bio_vec bv = req_bvec(req);
 
 		if (!is_pci_p2pdma_page(bv.bv_page)) {
-			if (bv.bv_offset + bv.bv_len <= NVME_CTRL_PAGE_SIZE * 2)
+			if ((bv.bv_offset & (NVME_CTRL_PAGE_SIZE - 1)) +
+			     bv.bv_len <= NVME_CTRL_PAGE_SIZE * 2)
 				return nvme_setup_prp_simple(dev, req,
 							     &cmnd->rw, &bv);
 
-			if (iod->nvmeq->qid && sgl_threshold &&
+			if (nvmeq->qid && sgl_threshold &&
 			    nvme_ctrl_sgl_supported(&dev->ctrl))
 				return nvme_setup_sgl_simple(dev, req,
 							     &cmnd->rw, &bv);
@@ -904,68 +887,85 @@
 	return BLK_STS_OK;
 }
 
-/*
- * NOTE: ns is NULL when called on the admin queue.
- */
-static blk_status_t nvme_queue_rq(struct blk_mq_hw_ctx *hctx,
-			 const struct blk_mq_queue_data *bd)
+static blk_status_t nvme_prep_rq(struct nvme_dev *dev, struct request *req)
 {
-	struct nvme_ns *ns = hctx->queue->queuedata;
-	struct nvme_queue *nvmeq = hctx->driver_data;
-	struct nvme_dev *dev = nvmeq->dev;
-	struct request *req = bd->rq;
 	struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
-	struct nvme_command *cmnd = &iod->cmd;
 	blk_status_t ret;
 
 	iod->aborted = 0;
 	iod->npages = -1;
 	iod->nents = 0;
 
-	/*
-	 * We should not need to do this, but we're still using this to
-	 * ensure we can drain requests on a dying queue.
-	 */
-	if (unlikely(!test_bit(NVMEQ_ENABLED, &nvmeq->flags)))
-		return BLK_STS_IOERR;
-
-	if (!nvme_check_ready(&dev->ctrl, req, true))
-		return nvme_fail_nonready_command(&dev->ctrl, req);
-
-	ret = nvme_setup_cmd(ns, req);
+	ret = nvme_setup_cmd(req->q->queuedata, req);
 	if (ret)
 		return ret;
 
 	if (blk_rq_nr_phys_segments(req)) {
-		ret = nvme_map_data(dev, req, cmnd);
+		ret = nvme_map_data(dev, req, &iod->cmd);
 		if (ret)
 			goto out_free_cmd;
 	}
 
 	if (blk_integrity_rq(req)) {
-		ret = nvme_map_metadata(dev, req, cmnd);
+		ret = nvme_map_metadata(dev, req, &iod->cmd);
 		if (ret)
 			goto out_unmap_data;
 	}
 
 	blk_mq_start_request(req);
-	nvme_submit_cmd(nvmeq, cmnd, bd->last);
 	return BLK_STS_OK;
 out_unmap_data:
-	nvme_unmap_data(dev, req);
+	if (blk_rq_nr_phys_segments(req))
+		nvme_unmap_data(dev, req);
 out_free_cmd:
 	nvme_cleanup_cmd(req);
 	return ret;
 }
 
-static void nvme_pci_complete_rq(struct request *req)
+/*
+ * NOTE: ns is NULL when called on the admin queue.
+ */
+static blk_status_t nvme_queue_rq(struct blk_mq_hw_ctx *hctx,
+			 const struct blk_mq_queue_data *bd)
 {
+	struct nvme_queue *nvmeq = hctx->driver_data;
+	struct nvme_dev *dev = nvmeq->dev;
+	struct request *req = bd->rq;
 	struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
-	struct nvme_dev *dev = iod->nvmeq->dev;
+	blk_status_t ret;
+
+	/*
+	 * We should not need to do this, but we're still using this to
+	 * ensure we can drain requests on a dying queue.
+	 */
+	if (unlikely(!test_bit(NVMEQ_ENABLED, &nvmeq->flags)))
+		return BLK_STS_IOERR;
+
+	if (unlikely(!nvme_check_ready(&dev->ctrl, req, true)))
+		return nvme_fail_nonready_command(&dev->ctrl, req);
+
+	ret = nvme_prep_rq(dev, req);
+	if (unlikely(ret))
+		return ret;
+	spin_lock(&nvmeq->sq_lock);
+	nvme_sq_copy_cmd(nvmeq, &iod->cmd);
+	nvme_write_sq_db(nvmeq, bd->last);
+	spin_unlock(&nvmeq->sq_lock);
+	return BLK_STS_OK;
+}
+
+static void nvme_pci_complete_rq(struct request *req)
+{
+	struct nvme_queue *nvmeq = req->mq_hctx->driver_data;
+	struct nvme_dev *dev = nvmeq->dev;
+
+	if (blk_integrity_rq(req)) {
+	        struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
 
-	if (blk_integrity_rq(req))
 		dma_unmap_page(dev->dev, iod->meta_dma,
-			       rq_integrity_vec(req)->bv_len, rq_data_dir(req));
+			       rq_integrity_vec(req)->bv_len, rq_dma_dir(req));
+	}
+
 	if (blk_rq_nr_phys_segments(req))
 		nvme_unmap_data(dev, req);
 	nvme_complete_rq(req);
@@ -1114,7 +1114,11 @@
 
 	c.common.opcode = nvme_admin_async_event;
 	c.common.command_id = NVME_AQ_BLK_MQ_DEPTH;
-	nvme_submit_cmd(nvmeq, &c, true);
+
+	spin_lock(&nvmeq->sq_lock);
+	nvme_sq_copy_cmd(nvmeq, &c);
+	nvme_write_sq_db(nvmeq, true);
+	spin_unlock(&nvmeq->sq_lock);
 }
 
 static int adapter_delete_queue(struct nvme_dev *dev, u8 opcode, u16 id)
@@ -1191,8 +1195,7 @@
 
 static void abort_endio(struct request *req, blk_status_t error)
 {
-	struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
-	struct nvme_queue *nvmeq = iod->nvmeq;
+	struct nvme_queue *nvmeq = req->mq_hctx->driver_data;
 
 	dev_warn(nvmeq->dev->ctrl.device,
 		 "Abort status: 0x%x", nvme_req(req)->status);
@@ -1246,7 +1249,7 @@
 static enum blk_eh_timer_return nvme_timeout(struct request *req, bool reserved)
 {
 	struct nvme_iod *iod = blk_mq_rq_to_pdu(req);
-	struct nvme_queue *nvmeq = iod->nvmeq;
+	struct nvme_queue *nvmeq = req->mq_hctx->driver_data;
 	struct nvme_dev *dev = nvmeq->dev;
 	struct request *abort_req;
 	struct nvme_command cmd = { };
@@ -1277,7 +1280,7 @@
 	else
 		nvme_poll_irqdisable(nvmeq);
 
-	if (blk_mq_request_completed(req)) {
+	if (blk_mq_rq_state(req) != MQ_RQ_IN_FLIGHT) {
 		dev_warn(dev->ctrl.device,
 			 "I/O %d QID %d timeout, completion polled\n",
 			 req->tag, nvmeq->qid);
@@ -1680,6 +1683,7 @@
 		dev->ctrl.admin_q = blk_mq_init_queue(&dev->admin_tagset);
 		if (IS_ERR(dev->ctrl.admin_q)) {
 			blk_mq_free_tag_set(&dev->admin_tagset);
+			dev->ctrl.admin_q = NULL;
 			return -ENOMEM;
 		}
 		if (!blk_get_queue(dev->ctrl.admin_q)) {
@@ -1846,6 +1850,18 @@
 		return;
 
 	/*
+	 * Controllers may support a CMB size larger than their BAR, for
+	 * example, due to being behind a bridge. Reduce the CMB to the
+	 * reported size of the BAR
+	 */
+	size = min(size, bar_size - offset);
+
+	if (!IS_ALIGNED(size, memremap_compat_align()) ||
+	    !IS_ALIGNED(pci_resource_start(pdev, bar),
+			memremap_compat_align()))
+		return;
+
+	/*
 	 * Tell the controller about the host side address mapping the CMB,
 	 * and enable CMB decoding for the NVMe 1.4+ scheme:
 	 */
@@ -1855,17 +1871,10 @@
 			     dev->bar + NVME_REG_CMBMSC);
 	}
 
-	/*
-	 * Controllers may support a CMB size larger than their BAR,
-	 * for example, due to being behind a bridge. Reduce the CMB to
-	 * the reported size of the BAR
-	 */
-	if (size > bar_size - offset)
-		size = bar_size - offset;
-
 	if (pci_p2pdma_add_resource(pdev, bar, size, offset)) {
 		dev_warn(dev->ctrl.device,
 			 "failed to register the CMB\n");
+		hi_lo_writeq(0, dev->bar + NVME_REG_CMBMSC);
 		return;
 	}
 
@@ -1918,10 +1927,10 @@
 
 	kfree(dev->host_mem_desc_bufs);
 	dev->host_mem_desc_bufs = NULL;
-	dma_free_coherent(dev->dev,
-			dev->nr_host_mem_descs * sizeof(*dev->host_mem_descs),
+	dma_free_coherent(dev->dev, dev->host_mem_descs_size,
 			dev->host_mem_descs, dev->host_mem_descs_dma);
 	dev->host_mem_descs = NULL;
+	dev->host_mem_descs_size = 0;
 	dev->nr_host_mem_descs = 0;
 }
 
@@ -1929,7 +1938,7 @@
 		u32 chunk_size)
 {
 	struct nvme_host_mem_buf_desc *descs;
-	u32 max_entries, len;
+	u32 max_entries, len, descs_size;
 	dma_addr_t descs_dma;
 	int i = 0;
 	void **bufs;
@@ -1942,8 +1951,9 @@
 	if (dev->ctrl.hmmaxd && dev->ctrl.hmmaxd < max_entries)
 		max_entries = dev->ctrl.hmmaxd;
 
-	descs = dma_alloc_coherent(dev->dev, max_entries * sizeof(*descs),
-				   &descs_dma, GFP_KERNEL);
+	descs_size = max_entries * sizeof(*descs);
+	descs = dma_alloc_coherent(dev->dev, descs_size, &descs_dma,
+			GFP_KERNEL);
 	if (!descs)
 		goto out;
 
@@ -1972,6 +1982,7 @@
 	dev->host_mem_size = size;
 	dev->host_mem_descs = descs;
 	dev->host_mem_descs_dma = descs_dma;
+	dev->host_mem_descs_size = descs_size;
 	dev->host_mem_desc_bufs = bufs;
 	return 0;
 
@@ -1986,8 +1997,7 @@
 
 	kfree(bufs);
 out_free_descs:
-	dma_free_coherent(dev->dev, max_entries * sizeof(*descs), descs,
-			descs_dma);
+	dma_free_coherent(dev->dev, descs_size, descs, descs_dma);
 out:
 	dev->host_mem_descs = NULL;
 	return -ENOMEM;
@@ -2515,15 +2525,8 @@
 	else
 		dev->io_sqes = NVME_NVM_IOSQES;
 
-	/*
-	 * Temporary fix for the Apple controller found in the MacBook8,1 and
-	 * some MacBook7,1 to avoid controller resets and data loss.
-	 */
-	if (pdev->vendor == PCI_VENDOR_ID_APPLE && pdev->device == 0x2001) {
+	if (dev->ctrl.quirks & NVME_QUIRK_QDEPTH_ONE) {
 		dev->q_depth = 2;
-		dev_warn(dev->ctrl.device, "detected Apple NVMe controller, "
-			"set queue depth=%u to work around controller resets\n",
-			dev->q_depth);
 	} else if (pdev->vendor == PCI_VENDOR_ID_SAMSUNG &&
 		   (pdev->device == 0xa821 || pdev->device == 0xa822) &&
 		   NVME_CAP_MQES(dev->ctrl.cap) == 0) {
@@ -2660,6 +2663,22 @@
 	dma_pool_destroy(dev->prp_small_pool);
 }
 
+static int nvme_pci_alloc_iod_mempool(struct nvme_dev *dev)
+{
+	size_t npages = max(nvme_pci_npages_prp(), nvme_pci_npages_sgl());
+	size_t alloc_size = sizeof(__le64 *) * npages +
+			    sizeof(struct scatterlist) * NVME_MAX_SEGS;
+
+	WARN_ON_ONCE(alloc_size > PAGE_SIZE);
+	dev->iod_mempool = mempool_create_node(1,
+			mempool_kmalloc, mempool_kfree,
+			(void *)alloc_size, GFP_KERNEL,
+			dev_to_node(dev->dev));
+	if (!dev->iod_mempool)
+		return -ENOMEM;
+	return 0;
+}
+
 static void nvme_free_tagset(struct nvme_dev *dev)
 {
 	if (dev->tagset.tags)
@@ -2667,6 +2686,7 @@
 	dev->ctrl.tagset = NULL;
 }
 
+/* pairs with nvme_pci_alloc_dev */
 static void nvme_pci_free_ctrl(struct nvme_ctrl *ctrl)
 {
 	struct nvme_dev *dev = to_nvme_dev(ctrl);
@@ -2731,6 +2751,8 @@
 	if (result)
 		goto out_unlock;
 
+	dma_set_min_align_mask(dev->dev, NVME_CTRL_PAGE_SIZE - 1);
+
 	/*
 	 * Limit the max command size to prevent iod->sg allocations going
 	 * over a single page.
@@ -2743,7 +2765,6 @@
 	 * Don't limit the IOMMU merged segment size.
 	 */
 	dma_set_max_seg_size(dev->dev, 0xffffffff);
-	dma_set_min_align_mask(dev->dev, NVME_CTRL_PAGE_SIZE - 1);
 
 	mutex_unlock(&dev->shutdown_lock);
 
@@ -2941,8 +2962,40 @@
 		if ((dmi_match(DMI_BOARD_VENDOR, "LENOVO")) &&
 		     dmi_match(DMI_BOARD_NAME, "LNVNB161216"))
 			return NVME_QUIRK_SIMPLE_SUSPEND;
+	} else if (pdev->vendor == 0x2646 && (pdev->device == 0x2263 ||
+		   pdev->device == 0x500f)) {
+		/*
+		 * Exclude some Kingston NV1 and A2000 devices from
+		 * NVME_QUIRK_SIMPLE_SUSPEND. Do a full suspend to save a
+		 * lot fo energy with s2idle sleep on some TUXEDO platforms.
+		 */
+		if (dmi_match(DMI_BOARD_NAME, "NS5X_NS7XAU") ||
+		    dmi_match(DMI_BOARD_NAME, "NS5x_7xAU") ||
+		    dmi_match(DMI_BOARD_NAME, "NS5x_7xPU") ||
+		    dmi_match(DMI_BOARD_NAME, "PH4PRX1_PH6PRX1"))
+			return NVME_QUIRK_FORCE_NO_SIMPLE_SUSPEND;
+	} else if (pdev->vendor == 0x144d && pdev->device == 0xa80d) {
+		/*
+		 * Exclude Samsung 990 Evo from NVME_QUIRK_SIMPLE_SUSPEND
+		 * because of high power consumption (> 2 Watt) in s2idle
+		 * sleep. Only some boards with Intel CPU are affected.
+		 */
+		if (dmi_match(DMI_BOARD_NAME, "DN50Z-140HC-YD") ||
+		    dmi_match(DMI_BOARD_NAME, "GMxPXxx") ||
+		    dmi_match(DMI_BOARD_NAME, "GXxMRXx") ||
+		    dmi_match(DMI_BOARD_NAME, "PH4PG31") ||
+		    dmi_match(DMI_BOARD_NAME, "PH4PRX1_PH6PRX1") ||
+		    dmi_match(DMI_BOARD_NAME, "PH6PG01_PH6PG71"))
+			return NVME_QUIRK_FORCE_NO_SIMPLE_SUSPEND;
 	}
 
+	/*
+	 * NVMe SSD drops off the PCIe bus after system idle
+	 * for 10 hours on a Lenovo N60z board.
+	 */
+	if (dmi_match(DMI_BOARD_NAME, "LXKT-ZXEG-N6"))
+		return NVME_QUIRK_NO_APST;
+
 	return 0;
 }
 
@@ -2955,20 +3008,20 @@
 	nvme_put_ctrl(&dev->ctrl);
 }
 
-static int nvme_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+static struct nvme_dev *nvme_pci_alloc_dev(struct pci_dev *pdev,
+		const struct pci_device_id *id)
 {
-	int node, result = -ENOMEM;
-	struct nvme_dev *dev;
 	unsigned long quirks = id->driver_data;
-	size_t alloc_size;
-
-	node = dev_to_node(&pdev->dev);
-	if (node == NUMA_NO_NODE)
-		set_dev_node(&pdev->dev, first_memory_node);
+	int node = dev_to_node(&pdev->dev);
+	struct nvme_dev *dev;
+	int ret = -ENOMEM;
 
 	dev = kzalloc_node(sizeof(*dev), GFP_KERNEL, node);
 	if (!dev)
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
+	INIT_WORK(&dev->ctrl.reset_work, nvme_reset_work);
+	INIT_WORK(&dev->remove_work, nvme_remove_dead_ctrl_work);
+	mutex_init(&dev->shutdown_lock);
 
 	dev->nr_write_queues = write_queues;
 	dev->nr_poll_queues = poll_queues;
@@ -2976,26 +3029,14 @@
 	dev->queues = kcalloc_node(dev->nr_allocated_queues,
 			sizeof(struct nvme_queue), GFP_KERNEL, node);
 	if (!dev->queues)
-		goto free;
+		goto out_free_dev;
 
 	dev->dev = get_device(&pdev->dev);
-	pci_set_drvdata(pdev, dev);
-
-	result = nvme_dev_map(dev);
-	if (result)
-		goto put_pci;
-
-	INIT_WORK(&dev->ctrl.reset_work, nvme_reset_work);
-	INIT_WORK(&dev->remove_work, nvme_remove_dead_ctrl_work);
-	mutex_init(&dev->shutdown_lock);
-
-	result = nvme_setup_prp_pools(dev);
-	if (result)
-		goto unmap;
 
 	quirks |= check_vendor_combination_bug(pdev);
-
-	if (!noacpi && acpi_storage_d3(&pdev->dev)) {
+	if (!noacpi &&
+	    !(quirks & NVME_QUIRK_FORCE_NO_SIMPLE_SUSPEND) &&
+	    acpi_storage_d3(&pdev->dev)) {
 		/*
 		 * Some systems use a bios work around to ask for D3 on
 		 * platforms that support kernel managed suspend.
@@ -3004,46 +3045,54 @@
 			 "platform quirk: setting simple suspend\n");
 		quirks |= NVME_QUIRK_SIMPLE_SUSPEND;
 	}
+	ret = nvme_init_ctrl(&dev->ctrl, &pdev->dev, &nvme_pci_ctrl_ops,
+			     quirks);
+	if (ret)
+		goto out_put_device;
+	return dev;
 
-	/*
-	 * Double check that our mempool alloc size will cover the biggest
-	 * command we support.
-	 */
-	alloc_size = nvme_pci_iod_alloc_size();
-	WARN_ON_ONCE(alloc_size > PAGE_SIZE);
+out_put_device:
+	put_device(dev->dev);
+	kfree(dev->queues);
+out_free_dev:
+	kfree(dev);
+	return ERR_PTR(ret);
+}
 
-	dev->iod_mempool = mempool_create_node(1, mempool_kmalloc,
-						mempool_kfree,
-						(void *) alloc_size,
-						GFP_KERNEL, node);
-	if (!dev->iod_mempool) {
-		result = -ENOMEM;
-		goto release_pools;
-	}
+static int nvme_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct nvme_dev *dev;
+	int result = -ENOMEM;
+
+	dev = nvme_pci_alloc_dev(pdev, id);
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
 
-	result = nvme_init_ctrl(&dev->ctrl, &pdev->dev, &nvme_pci_ctrl_ops,
-			quirks);
+	result = nvme_dev_map(dev);
+	if (result)
+		goto out_uninit_ctrl;
+
+	result = nvme_setup_prp_pools(dev);
+	if (result)
+		goto out_dev_unmap;
+
+	result = nvme_pci_alloc_iod_mempool(dev);
 	if (result)
-		goto release_mempool;
+		goto out_release_prp_pools;
 
 	dev_info(dev->ctrl.device, "pci function %s\n", dev_name(&pdev->dev));
+	pci_set_drvdata(pdev, dev);
 
 	nvme_reset_ctrl(&dev->ctrl);
 	async_schedule(nvme_async_probe, dev);
-
 	return 0;
 
- release_mempool:
-	mempool_destroy(dev->iod_mempool);
- release_pools:
+out_release_prp_pools:
 	nvme_release_prp_pools(dev);
- unmap:
+out_dev_unmap:
 	nvme_dev_unmap(dev);
- put_pci:
-	put_device(dev->dev);
- free:
-	kfree(dev->queues);
-	kfree(dev);
+out_uninit_ctrl:
+	nvme_uninit_ctrl(&dev->ctrl);
 	return result;
 }
 
@@ -3300,7 +3349,9 @@
 				NVME_QUIRK_DEALLOCATE_ZEROES, },
 	{ PCI_VDEVICE(INTEL, 0x0a54),	/* Intel P4500/P4600 */
 		.driver_data = NVME_QUIRK_STRIPE_SIZE |
-				NVME_QUIRK_DEALLOCATE_ZEROES, },
+				NVME_QUIRK_DEALLOCATE_ZEROES |
+				NVME_QUIRK_IGNORE_DEV_SUBNQN |
+				NVME_QUIRK_BOGUS_NID, },
 	{ PCI_VDEVICE(INTEL, 0x0a55),	/* Dell Express Flash P4600 */
 		.driver_data = NVME_QUIRK_STRIPE_SIZE |
 				NVME_QUIRK_DEALLOCATE_ZEROES, },
@@ -3313,7 +3364,15 @@
 		.driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN, },
 	{ PCI_VDEVICE(INTEL, 0x5845),	/* Qemu emulated controller */
 		.driver_data = NVME_QUIRK_IDENTIFY_CNS |
-				NVME_QUIRK_DISABLE_WRITE_ZEROES, },
+				NVME_QUIRK_DISABLE_WRITE_ZEROES |
+				NVME_QUIRK_BOGUS_NID, },
+	{ PCI_VDEVICE(REDHAT, 0x0010),	/* Qemu emulated controller */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1217, 0x8760), /* O2 Micro 64GB Steam Deck */
+		.driver_data = NVME_QUIRK_QDEPTH_ONE },
+	{ PCI_DEVICE(0x126f, 0x2262),	/* Silicon Motion generic */
+		.driver_data = NVME_QUIRK_NO_DEEPEST_PS |
+				NVME_QUIRK_BOGUS_NID, },
 	{ PCI_DEVICE(0x126f, 0x2263),	/* Silicon Motion unidentified */
 		.driver_data = NVME_QUIRK_NO_NS_DESC_LIST, },
 	{ PCI_DEVICE(0x1bb1, 0x0100),   /* Seagate Nytro Flash Storage */
@@ -3332,15 +3391,23 @@
 				NVME_QUIRK_DISABLE_WRITE_ZEROES|
 				NVME_QUIRK_IGNORE_DEV_SUBNQN, },
 	{ PCI_DEVICE(0x1987, 0x5016),	/* Phison E16 */
-		.driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN, },
+		.driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN |
+				NVME_QUIRK_BOGUS_NID, },
 	{ PCI_DEVICE(0x1b4b, 0x1092),	/* Lexar 256 GB SSD */
 		.driver_data = NVME_QUIRK_NO_NS_DESC_LIST |
 				NVME_QUIRK_IGNORE_DEV_SUBNQN, },
+	{ PCI_DEVICE(0x1cc1, 0x33f8),   /* ADATA IM2P33F8ABR1 1 TB */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
 	{ PCI_DEVICE(0x10ec, 0x5762),   /* ADATA SX6000LNP */
-		.driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN, },
+		.driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN |
+				NVME_QUIRK_BOGUS_NID, },
 	{ PCI_DEVICE(0x1cc1, 0x8201),   /* ADATA SX8200PNP 512GB */
 		.driver_data = NVME_QUIRK_NO_DEEPEST_PS |
 				NVME_QUIRK_IGNORE_DEV_SUBNQN, },
+	 { PCI_DEVICE(0x1344, 0x5407), /* Micron Technology Inc NVMe SSD */
+		.driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN },
+	 { PCI_DEVICE(0x1344, 0x6001),   /* Micron Nitro NVMe */
+		 .driver_data = NVME_QUIRK_BOGUS_NID, },
 	{ PCI_DEVICE(0x1c5c, 0x1504),   /* SK Hynix PC400 */
 		.driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, },
 	{ PCI_DEVICE(0x15b7, 0x2001),   /*  Sandisk Skyhawk */
@@ -3351,6 +3418,49 @@
 		.driver_data = NVME_QUIRK_NO_DEEPEST_PS, },
 	{ PCI_DEVICE(0x2646, 0x2263),   /* KINGSTON A2000 NVMe SSD  */
 		.driver_data = NVME_QUIRK_NO_DEEPEST_PS, },
+	{ PCI_DEVICE(0x2646, 0x5013),   /* Kingston KC3000, Kingston FURY Renegade */
+		.driver_data = NVME_QUIRK_NO_SECONDARY_TEMP_THRESH, },
+	{ PCI_DEVICE(0x2646, 0x5018),   /* KINGSTON OM8SFP4xxxxP OS21012 NVMe SSD */
+		.driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, },
+	{ PCI_DEVICE(0x2646, 0x5016),   /* KINGSTON OM3PGP4xxxxP OS21011 NVMe SSD */
+		.driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, },
+	{ PCI_DEVICE(0x2646, 0x501A),   /* KINGSTON OM8PGP4xxxxP OS21005 NVMe SSD */
+		.driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, },
+	{ PCI_DEVICE(0x2646, 0x501B),   /* KINGSTON OM8PGP4xxxxQ OS21005 NVMe SSD */
+		.driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, },
+	{ PCI_DEVICE(0x2646, 0x501E),   /* KINGSTON OM3PGP4xxxxQ OS21011 NVMe SSD */
+		.driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, },
+	{ PCI_DEVICE(0x1f40, 0x1202),   /* Netac Technologies Co. NV3000 NVMe SSD */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1f40, 0x5236),   /* Netac Technologies Co. NV7000 NVMe SSD */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1e4B, 0x1001),   /* MAXIO MAP1001 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1e4B, 0x1002),   /* MAXIO MAP1002 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1e4B, 0x1202),   /* MAXIO MAP1202 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1e4B, 0x1602),   /* MAXIO MAP1602 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1cc1, 0x5350),   /* ADATA XPG GAMMIX S50 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1e49, 0x0021),   /* ZHITAI TiPro5000 NVMe SSD */
+		.driver_data = NVME_QUIRK_NO_DEEPEST_PS, },
+	{ PCI_DEVICE(0x1e49, 0x0041),   /* ZHITAI TiPro7000 NVMe SSD */
+		.driver_data = NVME_QUIRK_NO_DEEPEST_PS, },
+	{ PCI_DEVICE(0xc0a9, 0x540a),   /* Crucial P2 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1d97, 0x2263), /* Lexar NM610 */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1d97, 0x2269), /* Lexar NM760 */
+		.driver_data = NVME_QUIRK_BOGUS_NID |
+				NVME_QUIRK_IGNORE_DEV_SUBNQN, },
+	{ PCI_DEVICE(0x10ec, 0x5763), /* TEAMGROUP T-FORCE CARDEA ZERO Z330 SSD */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x1e4b, 0x1602), /* HS-SSD-FUTURE 2048G  */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
+	{ PCI_DEVICE(0x10ec, 0x5765), /* TEAMGROUP MP33 2TB SSD */
+		.driver_data = NVME_QUIRK_BOGUS_NID, },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMAZON, 0x0061),
 		.driver_data = NVME_QUIRK_DMA_ADDRESS_BITS_48, },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMAZON, 0x0065),
@@ -3364,14 +3474,18 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMAZON, 0xcd02),
 		.driver_data = NVME_QUIRK_DMA_ADDRESS_BITS_48, },
 	{ PCI_DEVICE(PCI_VENDOR_ID_APPLE, 0x2001),
-		.driver_data = NVME_QUIRK_SINGLE_VECTOR },
+		/*
+		 * Fix for the Apple controller found in the MacBook8,1 and
+		 * some MacBook7,1 to avoid controller resets and data loss.
+		 */
+		.driver_data = NVME_QUIRK_SINGLE_VECTOR |
+				NVME_QUIRK_QDEPTH_ONE },
 	{ PCI_DEVICE(PCI_VENDOR_ID_APPLE, 0x2003) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_APPLE, 0x2005),
 		.driver_data = NVME_QUIRK_SINGLE_VECTOR |
 				NVME_QUIRK_128_BYTES_SQES |
 				NVME_QUIRK_SHARED_TAGS |
 				NVME_QUIRK_SKIP_CID_GEN },
-
 	{ PCI_DEVICE_CLASS(PCI_CLASS_STORAGE_EXPRESS, 0xffffff) },
 	{ 0, }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/rdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/rdma.c
@@ -645,6 +645,9 @@
 
 static void nvme_rdma_stop_queue(struct nvme_rdma_queue *queue)
 {
+	if (!test_bit(NVME_RDMA_Q_ALLOCATED, &queue->flags))
+		return;
+
 	mutex_lock(&queue->queue_lock);
 	if (test_and_clear_bit(NVME_RDMA_Q_LIVE, &queue->flags))
 		__nvme_rdma_stop_queue(queue);
@@ -698,11 +701,12 @@
 	return ret;
 }
 
-static int nvme_rdma_start_io_queues(struct nvme_rdma_ctrl *ctrl)
+static int nvme_rdma_start_io_queues(struct nvme_rdma_ctrl *ctrl,
+				     int first, int last)
 {
 	int i, ret = 0;
 
-	for (i = 1; i < ctrl->ctrl.queue_count; i++) {
+	for (i = first; i < last; i++) {
 		ret = nvme_rdma_start_queue(ctrl, i);
 		if (ret)
 			goto out_stop_queues;
@@ -711,7 +715,7 @@
 	return 0;
 
 out_stop_queues:
-	for (i--; i >= 1; i--)
+	for (i--; i >= first; i--)
 		nvme_rdma_stop_queue(&ctrl->queues[i]);
 	return ret;
 }
@@ -964,7 +968,7 @@
 
 static int nvme_rdma_configure_io_queues(struct nvme_rdma_ctrl *ctrl, bool new)
 {
-	int ret;
+	int ret, nr_queues;
 
 	ret = nvme_rdma_alloc_io_queues(ctrl);
 	if (ret)
@@ -984,11 +988,18 @@
 		}
 	}
 
-	ret = nvme_rdma_start_io_queues(ctrl);
+	/*
+	 * Only start IO queues for which we have allocated the tagset
+	 * and limitted it to the available queues. On reconnects, the
+	 * queue number might have changed.
+	 */
+	nr_queues = min(ctrl->tag_set.nr_hw_queues + 1, ctrl->ctrl.queue_count);
+	ret = nvme_rdma_start_io_queues(ctrl, 1, nr_queues);
 	if (ret)
 		goto out_cleanup_connect_q;
 
 	if (!new) {
+		nvme_start_freeze(&ctrl->ctrl);
 		nvme_start_queues(&ctrl->ctrl);
 		if (!nvme_wait_freeze_timeout(&ctrl->ctrl, NVME_IO_TIMEOUT)) {
 			/*
@@ -997,6 +1008,7 @@
 			 * to be safe.
 			 */
 			ret = -ENODEV;
+			nvme_unfreeze(&ctrl->ctrl);
 			goto out_wait_freeze_timed_out;
 		}
 		blk_mq_update_nr_hw_queues(ctrl->ctrl.tagset,
@@ -1004,6 +1016,15 @@
 		nvme_unfreeze(&ctrl->ctrl);
 	}
 
+	/*
+	 * If the number of queues has increased (reconnect case)
+	 * start all new queues now.
+	 */
+	ret = nvme_rdma_start_io_queues(ctrl, nr_queues,
+					ctrl->tag_set.nr_hw_queues + 1);
+	if (ret)
+		goto out_wait_freeze_timed_out;
+
 	return 0;
 
 out_wait_freeze_timed_out:
@@ -1038,7 +1059,6 @@
 		bool remove)
 {
 	if (ctrl->ctrl.queue_count > 1) {
-		nvme_start_freeze(&ctrl->ctrl);
 		nvme_stop_queues(&ctrl->ctrl);
 		nvme_sync_io_queues(&ctrl->ctrl);
 		nvme_rdma_stop_io_queues(ctrl);
@@ -1049,6 +1069,14 @@
 	}
 }
 
+static void nvme_rdma_stop_ctrl(struct nvme_ctrl *nctrl)
+{
+	struct nvme_rdma_ctrl *ctrl = to_rdma_ctrl(nctrl);
+
+	cancel_work_sync(&ctrl->err_work);
+	cancel_delayed_work_sync(&ctrl->reconnect_work);
+}
+
 static void nvme_rdma_free_ctrl(struct nvme_ctrl *nctrl)
 {
 	struct nvme_rdma_ctrl *ctrl = to_rdma_ctrl(nctrl);
@@ -1095,11 +1123,13 @@
 		return ret;
 
 	if (ctrl->ctrl.icdoff) {
+		ret = -EOPNOTSUPP;
 		dev_err(ctrl->ctrl.device, "icdoff is not supported!\n");
 		goto destroy_admin;
 	}
 
 	if (!(ctrl->ctrl.sgls & (1 << 2))) {
+		ret = -EOPNOTSUPP;
 		dev_err(ctrl->ctrl.device,
 			"Mandatory keyed sgls are not supported!\n");
 		goto destroy_admin;
@@ -1190,6 +1220,7 @@
 			struct nvme_rdma_ctrl, err_work);
 
 	nvme_stop_keep_alive(&ctrl->ctrl);
+	flush_work(&ctrl->ctrl.async_event_work);
 	nvme_rdma_teardown_io_queues(ctrl, false);
 	nvme_start_queues(&ctrl->ctrl);
 	nvme_rdma_teardown_admin_queue(ctrl, false);
@@ -2227,9 +2258,6 @@
 
 static void nvme_rdma_shutdown_ctrl(struct nvme_rdma_ctrl *ctrl, bool shutdown)
 {
-	cancel_work_sync(&ctrl->err_work);
-	cancel_delayed_work_sync(&ctrl->reconnect_work);
-
 	nvme_rdma_teardown_io_queues(ctrl, shutdown);
 	blk_mq_quiesce_queue(ctrl->ctrl.admin_q);
 	if (shutdown)
@@ -2279,6 +2307,7 @@
 	.submit_async_event	= nvme_rdma_submit_async_event,
 	.delete_ctrl		= nvme_rdma_delete_ctrl,
 	.get_address		= nvmf_get_address,
+	.stop_ctrl		= nvme_rdma_stop_ctrl,
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/tcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/tcp.c
@@ -30,6 +30,44 @@
 module_param(so_priority, int, 0644);
 MODULE_PARM_DESC(so_priority, "nvme tcp socket optimize priority");
 
+#ifdef CONFIG_DEBUG_LOCK_ALLOC
+/* lockdep can detect a circular dependency of the form
+ *   sk_lock -> mmap_lock (page fault) -> fs locks -> sk_lock
+ * because dependencies are tracked for both nvme-tcp and user contexts. Using
+ * a separate class prevents lockdep from conflating nvme-tcp socket use with
+ * user-space socket API use.
+ */
+static struct lock_class_key nvme_tcp_sk_key[2];
+static struct lock_class_key nvme_tcp_slock_key[2];
+
+static void nvme_tcp_reclassify_socket(struct socket *sock)
+{
+	struct sock *sk = sock->sk;
+
+	if (WARN_ON_ONCE(!sock_allow_reclassification(sk)))
+		return;
+
+	switch (sk->sk_family) {
+	case AF_INET:
+		sock_lock_init_class_and_name(sk, "slock-AF_INET-NVME",
+					      &nvme_tcp_slock_key[0],
+					      "sk_lock-AF_INET-NVME",
+					      &nvme_tcp_sk_key[0]);
+		break;
+	case AF_INET6:
+		sock_lock_init_class_and_name(sk, "slock-AF_INET6-NVME",
+					      &nvme_tcp_slock_key[1],
+					      "sk_lock-AF_INET6-NVME",
+					      &nvme_tcp_sk_key[1]);
+		break;
+	default:
+		WARN_ON_ONCE(1);
+	}
+}
+#else
+static void nvme_tcp_reclassify_socket(struct socket *sock) { }
+#endif
+
 enum nvme_tcp_send_state {
 	NVME_TCP_SEND_CMD_PDU = 0,
 	NVME_TCP_SEND_H2C_PDU,
@@ -81,7 +119,6 @@
 	struct mutex		send_mutex;
 	struct llist_head	req_list;
 	struct list_head	send_list;
-	bool			more_requests;
 
 	/* recv state */
 	void			*pdu;
@@ -277,7 +314,7 @@
 static inline bool nvme_tcp_queue_more(struct nvme_tcp_queue *queue)
 {
 	return !list_empty(&queue->send_list) ||
-		!llist_empty(&queue->req_list) || queue->more_requests;
+		!llist_empty(&queue->req_list);
 }
 
 static inline void nvme_tcp_queue_request(struct nvme_tcp_request *req,
@@ -296,9 +333,7 @@
 	 */
 	if (queue->io_cpu == raw_smp_processor_id() &&
 	    sync && empty && mutex_trylock(&queue->send_mutex)) {
-		queue->more_requests = !last;
 		nvme_tcp_send_all(queue);
-		queue->more_requests = false;
 		mutex_unlock(&queue->send_mutex);
 	}
 
@@ -920,7 +955,15 @@
 
 static void nvme_tcp_fail_request(struct nvme_tcp_request *req)
 {
-	nvme_tcp_end_request(blk_mq_rq_from_pdu(req), NVME_SC_HOST_PATH_ERROR);
+	if (nvme_tcp_async_req(req)) {
+		union nvme_result res = {};
+
+		nvme_complete_async_event(&req->queue->ctrl->ctrl,
+				cpu_to_le16(NVME_SC_HOST_PATH_ERROR), &res);
+	} else {
+		nvme_tcp_end_request(blk_mq_rq_from_pdu(req),
+				NVME_SC_HOST_PATH_ERROR);
+	}
 }
 
 static int nvme_tcp_try_send_data(struct nvme_tcp_request *req)
@@ -1116,8 +1159,7 @@
 	} else if (ret < 0) {
 		dev_err(queue->ctrl->ctrl.device,
 			"failed to send request %d\n", ret);
-		if (ret != -EPIPE && ret != -ECONNRESET)
-			nvme_tcp_fail_request(queue->request);
+		nvme_tcp_fail_request(queue->request);
 		nvme_tcp_done_send_req(queue);
 	}
 	return ret;
@@ -1164,7 +1206,7 @@
 		else if (unlikely(result < 0))
 			return;
 
-		if (!pending)
+		if (!pending || !queue->rd_enabled)
 			return;
 
 	} while (!time_after(jiffies, deadline)); /* quota is exhausted */
@@ -1428,6 +1470,8 @@
 		goto err_destroy_mutex;
 	}
 
+	nvme_tcp_reclassify_socket(queue->sock);
+
 	/* Single syn retry */
 	tcp_sock_set_syncnt(queue->sock->sk, 1);
 
@@ -1519,22 +1563,7 @@
 	if (ret)
 		goto err_init_connect;
 
-	queue->rd_enabled = true;
 	set_bit(NVME_TCP_Q_ALLOCATED, &queue->flags);
-	nvme_tcp_init_recv_ctx(queue);
-
-	write_lock_bh(&queue->sock->sk->sk_callback_lock);
-	queue->sock->sk->sk_user_data = queue;
-	queue->state_change = queue->sock->sk->sk_state_change;
-	queue->data_ready = queue->sock->sk->sk_data_ready;
-	queue->write_space = queue->sock->sk->sk_write_space;
-	queue->sock->sk->sk_data_ready = nvme_tcp_data_ready;
-	queue->sock->sk->sk_state_change = nvme_tcp_state_change;
-	queue->sock->sk->sk_write_space = nvme_tcp_write_space;
-#ifdef CONFIG_NET_RX_BUSY_POLL
-	queue->sock->sk->sk_ll_usec = 1;
-#endif
-	write_unlock_bh(&queue->sock->sk->sk_callback_lock);
 
 	return 0;
 
@@ -1554,7 +1583,7 @@
 	return ret;
 }
 
-static void nvme_tcp_restore_sock_calls(struct nvme_tcp_queue *queue)
+static void nvme_tcp_restore_sock_ops(struct nvme_tcp_queue *queue)
 {
 	struct socket *sock = queue->sock;
 
@@ -1569,7 +1598,7 @@
 static void __nvme_tcp_stop_queue(struct nvme_tcp_queue *queue)
 {
 	kernel_sock_shutdown(queue->sock, SHUT_RDWR);
-	nvme_tcp_restore_sock_calls(queue);
+	nvme_tcp_restore_sock_ops(queue);
 	cancel_work_sync(&queue->io_work);
 }
 
@@ -1584,21 +1613,42 @@
 	mutex_unlock(&queue->queue_lock);
 }
 
+static void nvme_tcp_setup_sock_ops(struct nvme_tcp_queue *queue)
+{
+	write_lock_bh(&queue->sock->sk->sk_callback_lock);
+	queue->sock->sk->sk_user_data = queue;
+	queue->state_change = queue->sock->sk->sk_state_change;
+	queue->data_ready = queue->sock->sk->sk_data_ready;
+	queue->write_space = queue->sock->sk->sk_write_space;
+	queue->sock->sk->sk_data_ready = nvme_tcp_data_ready;
+	queue->sock->sk->sk_state_change = nvme_tcp_state_change;
+	queue->sock->sk->sk_write_space = nvme_tcp_write_space;
+#ifdef CONFIG_NET_RX_BUSY_POLL
+	queue->sock->sk->sk_ll_usec = 1;
+#endif
+	write_unlock_bh(&queue->sock->sk->sk_callback_lock);
+}
+
 static int nvme_tcp_start_queue(struct nvme_ctrl *nctrl, int idx)
 {
 	struct nvme_tcp_ctrl *ctrl = to_tcp_ctrl(nctrl);
+	struct nvme_tcp_queue *queue = &ctrl->queues[idx];
 	int ret;
 
+	queue->rd_enabled = true;
+	nvme_tcp_init_recv_ctx(queue);
+	nvme_tcp_setup_sock_ops(queue);
+
 	if (idx)
 		ret = nvmf_connect_io_queue(nctrl, idx);
 	else
 		ret = nvmf_connect_admin_queue(nctrl);
 
 	if (!ret) {
-		set_bit(NVME_TCP_Q_LIVE, &ctrl->queues[idx].flags);
+		set_bit(NVME_TCP_Q_LIVE, &queue->flags);
 	} else {
-		if (test_bit(NVME_TCP_Q_ALLOCATED, &ctrl->queues[idx].flags))
-			__nvme_tcp_stop_queue(&ctrl->queues[idx]);
+		if (test_bit(NVME_TCP_Q_ALLOCATED, &queue->flags))
+			__nvme_tcp_stop_queue(queue);
 		dev_err(nctrl->device,
 			"failed to connect queue: %d ret=%d\n", idx, ret);
 	}
@@ -1673,11 +1723,12 @@
 		nvme_tcp_stop_queue(ctrl, i);
 }
 
-static int nvme_tcp_start_io_queues(struct nvme_ctrl *ctrl)
+static int nvme_tcp_start_io_queues(struct nvme_ctrl *ctrl,
+				    int first, int last)
 {
 	int i, ret = 0;
 
-	for (i = 1; i < ctrl->queue_count; i++) {
+	for (i = first; i < last; i++) {
 		ret = nvme_tcp_start_queue(ctrl, i);
 		if (ret)
 			goto out_stop_queues;
@@ -1686,7 +1737,7 @@
 	return 0;
 
 out_stop_queues:
-	for (i--; i >= 1; i--)
+	for (i--; i >= first; i--)
 		nvme_tcp_stop_queue(ctrl, i);
 	return ret;
 }
@@ -1813,7 +1864,7 @@
 
 static int nvme_tcp_configure_io_queues(struct nvme_ctrl *ctrl, bool new)
 {
-	int ret;
+	int ret, nr_queues;
 
 	ret = nvme_tcp_alloc_io_queues(ctrl);
 	if (ret)
@@ -1833,11 +1884,18 @@
 		}
 	}
 
-	ret = nvme_tcp_start_io_queues(ctrl);
+	/*
+	 * Only start IO queues for which we have allocated the tagset
+	 * and limitted it to the available queues. On reconnects, the
+	 * queue number might have changed.
+	 */
+	nr_queues = min(ctrl->tagset->nr_hw_queues + 1, ctrl->queue_count);
+	ret = nvme_tcp_start_io_queues(ctrl, 1, nr_queues);
 	if (ret)
 		goto out_cleanup_connect_q;
 
 	if (!new) {
+		nvme_start_freeze(ctrl);
 		nvme_start_queues(ctrl);
 		if (!nvme_wait_freeze_timeout(ctrl, NVME_IO_TIMEOUT)) {
 			/*
@@ -1846,6 +1904,7 @@
 			 * to be safe.
 			 */
 			ret = -ENODEV;
+			nvme_unfreeze(ctrl);
 			goto out_wait_freeze_timed_out;
 		}
 		blk_mq_update_nr_hw_queues(ctrl->tagset,
@@ -1853,6 +1912,15 @@
 		nvme_unfreeze(ctrl);
 	}
 
+	/*
+	 * If the number of queues has increased (reconnect case)
+	 * start all new queues now.
+	 */
+	ret = nvme_tcp_start_io_queues(ctrl, nr_queues,
+				       ctrl->tagset->nr_hw_queues + 1);
+	if (ret)
+		goto out_wait_freeze_timed_out;
+
 	return 0;
 
 out_wait_freeze_timed_out:
@@ -1964,7 +2032,6 @@
 	if (ctrl->queue_count <= 1)
 		return;
 	blk_mq_quiesce_queue(ctrl->admin_q);
-	nvme_start_freeze(ctrl);
 	nvme_stop_queues(ctrl);
 	nvme_sync_io_queues(ctrl);
 	nvme_tcp_stop_io_queues(ctrl);
@@ -2097,6 +2164,7 @@
 	struct nvme_ctrl *ctrl = &tcp_ctrl->ctrl;
 
 	nvme_stop_keep_alive(ctrl);
+	flush_work(&ctrl->async_event_work);
 	nvme_tcp_teardown_io_queues(ctrl, false);
 	/* unquiesce to fail fast pending requests */
 	nvme_start_queues(ctrl);
@@ -2115,9 +2183,6 @@
 
 static void nvme_tcp_teardown_ctrl(struct nvme_ctrl *ctrl, bool shutdown)
 {
-	cancel_work_sync(&to_tcp_ctrl(ctrl)->err_work);
-	cancel_delayed_work_sync(&to_tcp_ctrl(ctrl)->connect_work);
-
 	nvme_tcp_teardown_io_queues(ctrl, shutdown);
 	blk_mq_quiesce_queue(ctrl->admin_q);
 	if (shutdown)
@@ -2157,6 +2222,12 @@
 	nvme_tcp_reconnect_or_remove(ctrl);
 }
 
+static void nvme_tcp_stop_ctrl(struct nvme_ctrl *ctrl)
+{
+	cancel_work_sync(&to_tcp_ctrl(ctrl)->err_work);
+	cancel_delayed_work_sync(&to_tcp_ctrl(ctrl)->connect_work);
+}
+
 static void nvme_tcp_free_ctrl(struct nvme_ctrl *nctrl)
 {
 	struct nvme_tcp_ctrl *ctrl = to_tcp_ctrl(nctrl);
@@ -2436,6 +2507,7 @@
 {
 	struct nvme_tcp_queue *queue = hctx->driver_data;
 	struct sock *sk = queue->sock->sk;
+	int ret;
 
 	if (!test_bit(NVME_TCP_Q_LIVE, &queue->flags))
 		return 0;
@@ -2443,9 +2515,9 @@
 	set_bit(NVME_TCP_Q_POLLING, &queue->flags);
 	if (sk_can_busy_loop(sk) && skb_queue_empty_lockless(&sk->sk_receive_queue))
 		sk_busy_loop(sk, true);
-	nvme_tcp_try_recv(queue);
+	ret = nvme_tcp_try_recv(queue);
 	clear_bit(NVME_TCP_Q_POLLING, &queue->flags);
-	return queue->nr_cqe;
+	return ret < 0 ? ret : queue->nr_cqe;
 }
 
 static const struct blk_mq_ops nvme_tcp_mq_ops = {
@@ -2480,6 +2552,7 @@
 	.submit_async_event	= nvme_tcp_submit_async_event,
 	.delete_ctrl		= nvme_tcp_delete_ctrl,
 	.get_address		= nvmf_get_address,
+	.stop_ctrl		= nvme_tcp_stop_ctrl,
 };
 
 static bool
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/host/trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/host/trace.h
@@ -98,7 +98,7 @@
 	    TP_fast_assign(
 		__entry->ctrl_id = nvme_req(req)->ctrl->instance;
 		__entry->qid = nvme_req_qid(req);
-		__entry->cid = req->tag;
+		__entry->cid = nvme_req(req)->cmd->common.command_id;
 		__entry->result = le64_to_cpu(nvme_req(req)->result.u64);
 		__entry->retries = nvme_req(req)->retries;
 		__entry->flags = nvme_req(req)->flags;
@@ -127,15 +127,12 @@
 	),
 	TP_printk("nvme%d: NVME_AEN=%#08x [%s]",
 		__entry->ctrl_id, __entry->result,
-		__print_symbolic(__entry->result,
-		aer_name(NVME_AER_NOTICE_NS_CHANGED),
-		aer_name(NVME_AER_NOTICE_ANA),
-		aer_name(NVME_AER_NOTICE_FW_ACT_STARTING),
-		aer_name(NVME_AER_NOTICE_DISC_CHANGED),
-		aer_name(NVME_AER_ERROR),
-		aer_name(NVME_AER_SMART),
-		aer_name(NVME_AER_CSS),
-		aer_name(NVME_AER_VS))
+		__print_symbolic(__entry->result & 0x7,
+			aer_name(NVME_AER_ERROR),
+			aer_name(NVME_AER_SMART),
+			aer_name(NVME_AER_NOTICE),
+			aer_name(NVME_AER_CSS),
+			aer_name(NVME_AER_VS))
 	)
 );
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/admin-cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/admin-cmd.c
@@ -164,26 +164,29 @@
 
 static void nvmet_get_cmd_effects_nvm(struct nvme_effects_log *log)
 {
-	log->acs[nvme_admin_get_log_page]	= cpu_to_le32(1 << 0);
-	log->acs[nvme_admin_identify]		= cpu_to_le32(1 << 0);
-	log->acs[nvme_admin_abort_cmd]		= cpu_to_le32(1 << 0);
-	log->acs[nvme_admin_set_features]	= cpu_to_le32(1 << 0);
-	log->acs[nvme_admin_get_features]	= cpu_to_le32(1 << 0);
-	log->acs[nvme_admin_async_event]	= cpu_to_le32(1 << 0);
-	log->acs[nvme_admin_keep_alive]		= cpu_to_le32(1 << 0);
-
-	log->iocs[nvme_cmd_read]		= cpu_to_le32(1 << 0);
-	log->iocs[nvme_cmd_write]		= cpu_to_le32(1 << 0);
-	log->iocs[nvme_cmd_flush]		= cpu_to_le32(1 << 0);
-	log->iocs[nvme_cmd_dsm]			= cpu_to_le32(1 << 0);
-	log->iocs[nvme_cmd_write_zeroes]	= cpu_to_le32(1 << 0);
+	log->acs[nvme_admin_get_log_page] =
+	log->acs[nvme_admin_identify] =
+	log->acs[nvme_admin_abort_cmd] =
+	log->acs[nvme_admin_set_features] =
+	log->acs[nvme_admin_get_features] =
+	log->acs[nvme_admin_async_event] =
+	log->acs[nvme_admin_keep_alive] =
+		cpu_to_le32(NVME_CMD_EFFECTS_CSUPP);
+
+	log->iocs[nvme_cmd_read] =
+	log->iocs[nvme_cmd_write] =
+	log->iocs[nvme_cmd_flush] =
+	log->iocs[nvme_cmd_dsm]	=
+	log->iocs[nvme_cmd_write_zeroes] =
+		cpu_to_le32(NVME_CMD_EFFECTS_CSUPP);
 }
 
 static void nvmet_get_cmd_effects_zns(struct nvme_effects_log *log)
 {
-	log->iocs[nvme_cmd_zone_append]		= cpu_to_le32(1 << 0);
-	log->iocs[nvme_cmd_zone_mgmt_send]	= cpu_to_le32(1 << 0);
-	log->iocs[nvme_cmd_zone_mgmt_recv]	= cpu_to_le32(1 << 0);
+	log->iocs[nvme_cmd_zone_append] =
+	log->iocs[nvme_cmd_zone_mgmt_send] =
+	log->iocs[nvme_cmd_zone_mgmt_recv] =
+		cpu_to_le32(NVME_CMD_EFFECTS_CSUPP);
 }
 
 static void nvmet_execute_get_log_cmd_effects_ns(struct nvmet_req *req)
@@ -505,7 +508,11 @@
 		goto done;
 	}
 
-	nvmet_ns_revalidate(req->ns);
+	if (nvmet_ns_revalidate(req->ns)) {
+		mutex_lock(&req->ns->subsys->lock);
+		nvmet_ns_changed(req->ns->subsys, req->ns->nsid);
+		mutex_unlock(&req->ns->subsys->lock);
+	}
 
 	/*
 	 * nuse = ncap = nsze isn't always true, but we have no way to find
@@ -673,6 +680,13 @@
 	}
 }
 
+static void nvmet_execute_identify_ctrl_nvm(struct nvmet_req *req)
+{
+	/* Not supported: return zeroes */
+	nvmet_req_complete(req,
+		   nvmet_zero_sgl(req, 0, sizeof(struct nvme_id_ctrl_nvm)));
+}
+
 static void nvmet_execute_identify(struct nvmet_req *req)
 {
 	if (!nvmet_check_transfer_len(req, NVME_IDENTIFY_DATA_SIZE))
@@ -680,13 +694,8 @@
 
 	switch (req->cmd->identify.cns) {
 	case NVME_ID_CNS_NS:
-		switch (req->cmd->identify.csi) {
-		case NVME_CSI_NVM:
-			return nvmet_execute_identify_ns(req);
-		default:
-			break;
-		}
-		break;
+		nvmet_execute_identify_ns(req);
+		return;
 	case NVME_ID_CNS_CS_NS:
 		if (IS_ENABLED(CONFIG_BLK_DEV_ZONED)) {
 			switch (req->cmd->identify.csi) {
@@ -698,29 +707,24 @@
 		}
 		break;
 	case NVME_ID_CNS_CTRL:
-		switch (req->cmd->identify.csi) {
-		case NVME_CSI_NVM:
-			return nvmet_execute_identify_ctrl(req);
-		}
-		break;
+		nvmet_execute_identify_ctrl(req);
+		return;
 	case NVME_ID_CNS_CS_CTRL:
-		if (IS_ENABLED(CONFIG_BLK_DEV_ZONED)) {
-			switch (req->cmd->identify.csi) {
-			case NVME_CSI_ZNS:
-				return nvmet_execute_identify_cns_cs_ctrl(req);
-			default:
-				break;
-			}
-		}
-		break;
-	case NVME_ID_CNS_NS_ACTIVE_LIST:
 		switch (req->cmd->identify.csi) {
 		case NVME_CSI_NVM:
-			return nvmet_execute_identify_nslist(req);
-		default:
+			nvmet_execute_identify_ctrl_nvm(req);
+			return;
+		case NVME_CSI_ZNS:
+			if (IS_ENABLED(CONFIG_BLK_DEV_ZONED)) {
+				nvmet_execute_identify_ctrl_zns(req);
+				return;
+			}
 			break;
 		}
 		break;
+	case NVME_ID_CNS_NS_ACTIVE_LIST:
+		nvmet_execute_identify_nslist(req);
+		return;
 	case NVME_ID_CNS_NS_DESC_LIST:
 		if (nvmet_handle_identify_desclist(req) == true)
 			return;
@@ -978,7 +982,7 @@
 	ctrl->async_event_cmds[ctrl->nr_async_event_cmds++] = req;
 	mutex_unlock(&ctrl->lock);
 
-	schedule_work(&ctrl->async_event_work);
+	queue_work(nvmet_wq, &ctrl->async_event_work);
 }
 
 void nvmet_execute_keep_alive(struct nvmet_req *req)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/configfs.c
@@ -530,10 +530,18 @@
 	if (strtobool(page, &enable))
 		return -EINVAL;
 
+	/*
+	 * take a global nvmet_config_sem because the disable routine has a
+	 * window where it releases the subsys-lock, giving a chance to
+	 * a parallel enable to concurrently execute causing the disable to
+	 * have a misaccounting of the ns percpu_ref.
+	 */
+	down_write(&nvmet_config_sem);
 	if (enable)
 		ret = nvmet_ns_enable(ns);
 	else
 		nvmet_ns_disable(ns);
+	up_write(&nvmet_config_sem);
 
 	return ret ? ret : count;
 }
@@ -586,7 +594,8 @@
 		mutex_unlock(&ns->subsys->lock);
 		return -EINVAL;
 	}
-	nvmet_ns_revalidate(ns);
+	if (nvmet_ns_revalidate(ns))
+		nvmet_ns_changed(ns->subsys, ns->nsid);
 	mutex_unlock(&ns->subsys->lock);
 	return count;
 }
@@ -1189,6 +1198,7 @@
 		const char *page, size_t count)
 {
 	int pos = 0, len;
+	char *val;
 
 	if (subsys->subsys_discovered) {
 		pr_err("Can't set model number. %s is already assigned\n",
@@ -1211,9 +1221,11 @@
 			return -EINVAL;
 	}
 
-	subsys->model_number = kmemdup_nul(page, len, GFP_KERNEL);
-	if (!subsys->model_number)
+	val = kmemdup_nul(page, len, GFP_KERNEL);
+	if (!val)
 		return -ENOMEM;
+	kfree(subsys->model_number);
+	subsys->model_number = val;
 	return count;
 }
 
@@ -1255,6 +1267,34 @@
 CONFIGFS_ATTR(nvmet_subsys_, attr_pi_enable);
 #endif
 
+static ssize_t nvmet_subsys_attr_qid_max_show(struct config_item *item,
+					      char *page)
+{
+	return snprintf(page, PAGE_SIZE, "%u\n", to_subsys(item)->max_qid);
+}
+
+static ssize_t nvmet_subsys_attr_qid_max_store(struct config_item *item,
+					       const char *page, size_t cnt)
+{
+	struct nvmet_port *port = to_nvmet_port(item);
+	u16 qid_max;
+
+	if (nvmet_is_port_enabled(port, __func__))
+		return -EACCES;
+
+	if (sscanf(page, "%hu\n", &qid_max) != 1)
+		return -EINVAL;
+
+	if (qid_max < 1 || qid_max > NVMET_NR_QUEUES)
+		return -EINVAL;
+
+	down_write(&nvmet_config_sem);
+	to_subsys(item)->max_qid = qid_max;
+	up_write(&nvmet_config_sem);
+	return cnt;
+}
+CONFIGFS_ATTR(nvmet_subsys_, attr_qid_max);
+
 static struct configfs_attribute *nvmet_subsys_attrs[] = {
 	&nvmet_subsys_attr_attr_allow_any_host,
 	&nvmet_subsys_attr_attr_version,
@@ -1262,6 +1302,7 @@
 	&nvmet_subsys_attr_attr_cntlid_min,
 	&nvmet_subsys_attr_attr_cntlid_max,
 	&nvmet_subsys_attr_attr_model,
+	&nvmet_subsys_attr_attr_qid_max,
 #ifdef CONFIG_BLK_DEV_INTEGRITY
 	&nvmet_subsys_attr_attr_pi_enable,
 #endif
@@ -1553,6 +1594,8 @@
 {
 	struct nvmet_port *port = to_nvmet_port(item);
 
+	/* Let inflight controllers teardown complete */
+	flush_workqueue(nvmet_wq);
 	list_del(&port->global_entry);
 
 	kfree(port->ana_state);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/core.c
@@ -15,11 +15,15 @@
 
 #include "nvmet.h"
 
+struct kmem_cache *nvmet_bvec_cache;
 struct workqueue_struct *buffered_io_wq;
 struct workqueue_struct *zbd_wq;
 static const struct nvmet_fabrics_ops *nvmet_transports[NVMF_TRTYPE_MAX];
 static DEFINE_IDA(cntlid_ida);
 
+struct workqueue_struct *nvmet_wq;
+EXPORT_SYMBOL_GPL(nvmet_wq);
+
 /*
  * This read/write semaphore is used to synchronize access to configuration
  * information on a target system that will result in discovery log page
@@ -205,7 +209,7 @@
 	list_add_tail(&aen->entry, &ctrl->async_events);
 	mutex_unlock(&ctrl->lock);
 
-	schedule_work(&ctrl->async_event_work);
+	queue_work(nvmet_wq, &ctrl->async_event_work);
 }
 
 static void nvmet_add_to_changed_ns_log(struct nvmet_ctrl *ctrl, __le32 nsid)
@@ -385,7 +389,7 @@
 	if (reset_tbkas) {
 		pr_debug("ctrl %d reschedule traffic based keep-alive timer\n",
 			ctrl->cntlid);
-		schedule_delayed_work(&ctrl->ka_work, ctrl->kato * HZ);
+		queue_delayed_work(nvmet_wq, &ctrl->ka_work, ctrl->kato * HZ);
 		return;
 	}
 
@@ -403,7 +407,7 @@
 	pr_debug("ctrl %d start keep-alive timer for %d secs\n",
 		ctrl->cntlid, ctrl->kato);
 
-	schedule_delayed_work(&ctrl->ka_work, ctrl->kato * HZ);
+	queue_delayed_work(nvmet_wq, &ctrl->ka_work, ctrl->kato * HZ);
 }
 
 void nvmet_stop_keep_alive_timer(struct nvmet_ctrl *ctrl)
@@ -531,7 +535,7 @@
 		ns->nsid);
 }
 
-void nvmet_ns_revalidate(struct nvmet_ns *ns)
+bool nvmet_ns_revalidate(struct nvmet_ns *ns)
 {
 	loff_t oldsize = ns->size;
 
@@ -540,8 +544,7 @@
 	else
 		nvmet_file_ns_revalidate(ns);
 
-	if (oldsize != ns->size)
-		nvmet_ns_changed(ns->subsys, ns->nsid);
+	return oldsize != ns->size;
 }
 
 int nvmet_ns_enable(struct nvmet_ns *ns)
@@ -733,6 +736,8 @@
 
 static void __nvmet_req_complete(struct nvmet_req *req, u16 status)
 {
+	struct nvmet_ns *ns = req->ns;
+
 	if (!req->sq->sqhd_disabled)
 		nvmet_update_sq_head(req);
 	req->cqe->sq_id = cpu_to_le16(req->sq->qid);
@@ -743,15 +748,17 @@
 
 	trace_nvmet_req_complete(req);
 
-	if (req->ns)
-		nvmet_put_namespace(req->ns);
 	req->ops->queue_response(req);
+	if (ns)
+		nvmet_put_namespace(ns);
 }
 
 void nvmet_req_complete(struct nvmet_req *req, u16 status)
 {
+	struct nvmet_sq *sq = req->sq;
+
 	__nvmet_req_complete(req, status);
-	percpu_ref_put(&req->sq->ref);
+	percpu_ref_put(&sq->ref);
 }
 EXPORT_SYMBOL_GPL(nvmet_req_complete);
 
@@ -794,6 +801,15 @@
 	wait_for_completion(&sq->free_done);
 	percpu_ref_exit(&sq->ref);
 
+	/*
+	 * we must reference the ctrl again after waiting for inflight IO
+	 * to complete. Because admin connect may have sneaked in after we
+	 * store sq->ctrl locally, but before we killed the percpu_ref. the
+	 * admin connect allocates and assigns sq->ctrl, which now needs a
+	 * final ref put, as this ctrl is going away.
+	 */
+	ctrl = sq->ctrl;
+
 	if (ctrl) {
 		/*
 		 * The teardown flow may take some time, and the host may not
@@ -1163,7 +1179,7 @@
 	 * reset the keep alive timer when the controller is enabled.
 	 */
 	if (ctrl->kato)
-		mod_delayed_work(system_wq, &ctrl->ka_work, ctrl->kato * HZ);
+		mod_delayed_work(nvmet_wq, &ctrl->ka_work, ctrl->kato * HZ);
 }
 
 static void nvmet_clear_ctrl(struct nvmet_ctrl *ctrl)
@@ -1477,7 +1493,7 @@
 	mutex_lock(&ctrl->lock);
 	if (!(ctrl->csts & NVME_CSTS_CFS)) {
 		ctrl->csts |= NVME_CSTS_CFS;
-		schedule_work(&ctrl->fatal_err_work);
+		queue_work(nvmet_wq, &ctrl->fatal_err_work);
 	}
 	mutex_unlock(&ctrl->lock);
 }
@@ -1602,24 +1618,32 @@
 
 static int __init nvmet_init(void)
 {
-	int error;
+	int error = -ENOMEM;
 
 	nvmet_ana_group_enabled[NVMET_DEFAULT_ANA_GRPID] = 1;
 
+	nvmet_bvec_cache = kmem_cache_create("nvmet-bvec",
+			NVMET_MAX_MPOOL_BVEC * sizeof(struct bio_vec), 0,
+			SLAB_HWCACHE_ALIGN, NULL);
+	if (!nvmet_bvec_cache)
+		return -ENOMEM;
+
 	zbd_wq = alloc_workqueue("nvmet-zbd-wq", WQ_MEM_RECLAIM, 0);
 	if (!zbd_wq)
-		return -ENOMEM;
+		goto out_destroy_bvec_cache;
 
 	buffered_io_wq = alloc_workqueue("nvmet-buffered-io-wq",
 			WQ_MEM_RECLAIM, 0);
-	if (!buffered_io_wq) {
-		error = -ENOMEM;
+	if (!buffered_io_wq)
 		goto out_free_zbd_work_queue;
-	}
+
+	nvmet_wq = alloc_workqueue("nvmet-wq", WQ_MEM_RECLAIM, 0);
+	if (!nvmet_wq)
+		goto out_free_buffered_work_queue;
 
 	error = nvmet_init_discovery();
 	if (error)
-		goto out_free_work_queue;
+		goto out_free_nvmet_work_queue;
 
 	error = nvmet_init_configfs();
 	if (error)
@@ -1628,10 +1652,14 @@
 
 out_exit_discovery:
 	nvmet_exit_discovery();
-out_free_work_queue:
+out_free_nvmet_work_queue:
+	destroy_workqueue(nvmet_wq);
+out_free_buffered_work_queue:
 	destroy_workqueue(buffered_io_wq);
 out_free_zbd_work_queue:
 	destroy_workqueue(zbd_wq);
+out_destroy_bvec_cache:
+	kmem_cache_destroy(nvmet_bvec_cache);
 	return error;
 }
 
@@ -1640,8 +1668,10 @@
 	nvmet_exit_configfs();
 	nvmet_exit_discovery();
 	ida_destroy(&cntlid_ida);
+	destroy_workqueue(nvmet_wq);
 	destroy_workqueue(buffered_io_wq);
 	destroy_workqueue(zbd_wq);
+	kmem_cache_destroy(nvmet_bvec_cache);
 
 	BUILD_BUG_ON(sizeof(struct nvmf_disc_rsp_page_entry) != 1024);
 	BUILD_BUG_ON(sizeof(struct nvmf_disc_rsp_page_hdr) != 1024);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/fabrics-cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/fabrics-cmd.c
@@ -206,6 +206,8 @@
 		goto out;
 	}
 
+	d->subsysnqn[NVMF_NQN_FIELD_LEN - 1] = '\0';
+	d->hostnqn[NVMF_NQN_FIELD_LEN - 1] = '\0';
 	status = nvmet_alloc_ctrl(d->subsysnqn, d->hostnqn, req,
 				  le32_to_cpu(c->kato), &ctrl);
 	if (status)
@@ -263,6 +265,8 @@
 		goto out;
 	}
 
+	d->subsysnqn[NVMF_NQN_FIELD_LEN - 1] = '\0';
+	d->hostnqn[NVMF_NQN_FIELD_LEN - 1] = '\0';
 	ctrl = nvmet_ctrl_find_get(d->subsysnqn, d->hostnqn,
 				   le16_to_cpu(d->cntlid), req);
 	if (!ctrl) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/fc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/fc.c
@@ -111,6 +111,8 @@
 	struct nvmet_fc_port_entry	*pe;
 	struct kref			ref;
 	u32				max_sg_cnt;
+
+	struct work_struct		put_work;
 };
 
 struct nvmet_fc_port_entry {
@@ -165,7 +167,7 @@
 	struct nvmet_fc_hostport	*hostport;
 	struct nvmet_fc_ls_iod		*rcv_disconn;
 	struct list_head		a_list;
-	struct nvmet_fc_tgt_queue __rcu	*queues[NVMET_NR_QUEUES + 1];
+	struct nvmet_fc_tgt_queue 	*queues[NVMET_NR_QUEUES + 1];
 	struct kref			ref;
 	struct work_struct		del_work;
 	struct rcu_head			rcu;
@@ -248,6 +250,13 @@
 static void nvmet_fc_tgt_q_put(struct nvmet_fc_tgt_queue *queue);
 static int nvmet_fc_tgt_q_get(struct nvmet_fc_tgt_queue *queue);
 static void nvmet_fc_tgtport_put(struct nvmet_fc_tgtport *tgtport);
+static void nvmet_fc_put_tgtport_work(struct work_struct *work)
+{
+	struct nvmet_fc_tgtport *tgtport =
+		container_of(work, struct nvmet_fc_tgtport, put_work);
+
+	nvmet_fc_tgtport_put(tgtport);
+}
 static int nvmet_fc_tgtport_get(struct nvmet_fc_tgtport *tgtport);
 static void nvmet_fc_handle_fcp_rqst(struct nvmet_fc_tgtport *tgtport,
 					struct nvmet_fc_fcp_iod *fod);
@@ -359,7 +368,7 @@
 
 	if (!lsop->req_queued) {
 		spin_unlock_irqrestore(&tgtport->lock, flags);
-		return;
+		goto out_putwork;
 	}
 
 	list_del(&lsop->lsreq_list);
@@ -372,7 +381,8 @@
 				  (lsreq->rqstlen + lsreq->rsplen),
 				  DMA_BIDIRECTIONAL);
 
-	nvmet_fc_tgtport_put(tgtport);
+out_putwork:
+	queue_work(nvmet_wq, &tgtport->put_work);
 }
 
 static int
@@ -801,14 +811,11 @@
 	if (!queue)
 		return NULL;
 
-	if (!nvmet_fc_tgt_a_get(assoc))
-		goto out_free_queue;
-
 	queue->work_q = alloc_workqueue("ntfc%d.%d.%d", 0, 0,
 				assoc->tgtport->fc_target_port.port_num,
 				assoc->a_id, qid);
 	if (!queue->work_q)
-		goto out_a_put;
+		goto out_free_queue;
 
 	queue->qid = qid;
 	queue->sqsize = sqsize;
@@ -830,15 +837,13 @@
 		goto out_fail_iodlist;
 
 	WARN_ON(assoc->queues[qid]);
-	rcu_assign_pointer(assoc->queues[qid], queue);
+	assoc->queues[qid] = queue;
 
 	return queue;
 
 out_fail_iodlist:
 	nvmet_fc_destroy_fcp_iodlist(assoc->tgtport, queue);
 	destroy_workqueue(queue->work_q);
-out_a_put:
-	nvmet_fc_tgt_a_put(assoc);
 out_free_queue:
 	kfree(queue);
 	return NULL;
@@ -851,12 +856,8 @@
 	struct nvmet_fc_tgt_queue *queue =
 		container_of(ref, struct nvmet_fc_tgt_queue, ref);
 
-	rcu_assign_pointer(queue->assoc->queues[queue->qid], NULL);
-
 	nvmet_fc_destroy_fcp_iodlist(queue->assoc->tgtport, queue);
 
-	nvmet_fc_tgt_a_put(queue->assoc);
-
 	destroy_workqueue(queue->work_q);
 
 	kfree_rcu(queue, rcu);
@@ -968,7 +969,7 @@
 	rcu_read_lock();
 	list_for_each_entry_rcu(assoc, &tgtport->assoc_list, a_list) {
 		if (association_id == assoc->association_id) {
-			queue = rcu_dereference(assoc->queues[qid]);
+			queue = assoc->queues[qid];
 			if (queue &&
 			    (!atomic_read(&queue->connected) ||
 			     !nvmet_fc_tgt_q_get(queue)))
@@ -1077,8 +1078,6 @@
 		/* new allocation not needed */
 		kfree(newhost);
 		newhost = match;
-		/* no new allocation - release reference */
-		nvmet_fc_tgtport_put(tgtport);
 	} else {
 		newhost->tgtport = tgtport;
 		newhost->hosthandle = hosthandle;
@@ -1093,13 +1092,28 @@
 }
 
 static void
-nvmet_fc_delete_assoc(struct work_struct *work)
+nvmet_fc_delete_assoc(struct nvmet_fc_tgt_assoc *assoc)
+{
+	nvmet_fc_delete_target_assoc(assoc);
+	nvmet_fc_tgt_a_put(assoc);
+}
+
+static void
+nvmet_fc_delete_assoc_work(struct work_struct *work)
 {
 	struct nvmet_fc_tgt_assoc *assoc =
 		container_of(work, struct nvmet_fc_tgt_assoc, del_work);
+	struct nvmet_fc_tgtport *tgtport = assoc->tgtport;
 
-	nvmet_fc_delete_target_assoc(assoc);
-	nvmet_fc_tgt_a_put(assoc);
+	nvmet_fc_delete_assoc(assoc);
+	nvmet_fc_tgtport_put(tgtport);
+}
+
+static void
+nvmet_fc_schedule_delete_assoc(struct nvmet_fc_tgt_assoc *assoc)
+{
+	nvmet_fc_tgtport_get(assoc->tgtport);
+	queue_work(nvmet_wq, &assoc->del_work);
 }
 
 static struct nvmet_fc_tgt_assoc *
@@ -1111,6 +1125,9 @@
 	int idx;
 	bool needrandom = true;
 
+	if (!tgtport->pe)
+		return NULL;
+
 	assoc = kzalloc(sizeof(*assoc), GFP_KERNEL);
 	if (!assoc)
 		return NULL;
@@ -1130,7 +1147,7 @@
 	assoc->a_id = idx;
 	INIT_LIST_HEAD(&assoc->a_list);
 	kref_init(&assoc->ref);
-	INIT_WORK(&assoc->del_work, nvmet_fc_delete_assoc);
+	INIT_WORK(&assoc->del_work, nvmet_fc_delete_assoc_work);
 	atomic_set(&assoc->terminating, 0);
 
 	while (needrandom) {
@@ -1171,13 +1188,18 @@
 	struct nvmet_fc_tgtport *tgtport = assoc->tgtport;
 	struct nvmet_fc_ls_iod	*oldls;
 	unsigned long flags;
+	int i;
+
+	for (i = NVMET_NR_QUEUES; i >= 0; i--) {
+		if (assoc->queues[i])
+			nvmet_fc_delete_target_queue(assoc->queues[i]);
+	}
 
 	/* Send Disconnect now that all i/o has completed */
 	nvmet_fc_xmt_disconnect_assoc(assoc);
 
 	nvmet_fc_free_hostport(assoc->hostport);
 	spin_lock_irqsave(&tgtport->lock, flags);
-	list_del_rcu(&assoc->a_list);
 	oldls = assoc->rcv_disconn;
 	spin_unlock_irqrestore(&tgtport->lock, flags);
 	/* if pending Rcv Disconnect Association LS, send rsp now */
@@ -1207,7 +1229,7 @@
 nvmet_fc_delete_target_assoc(struct nvmet_fc_tgt_assoc *assoc)
 {
 	struct nvmet_fc_tgtport *tgtport = assoc->tgtport;
-	struct nvmet_fc_tgt_queue *queue;
+	unsigned long flags;
 	int i, terminating;
 
 	terminating = atomic_xchg(&assoc->terminating, 1);
@@ -1216,29 +1238,21 @@
 	if (terminating)
 		return;
 
+	spin_lock_irqsave(&tgtport->lock, flags);
+	list_del_rcu(&assoc->a_list);
+	spin_unlock_irqrestore(&tgtport->lock, flags);
 
-	for (i = NVMET_NR_QUEUES; i >= 0; i--) {
-		rcu_read_lock();
-		queue = rcu_dereference(assoc->queues[i]);
-		if (!queue) {
-			rcu_read_unlock();
-			continue;
-		}
+	synchronize_rcu();
 
-		if (!nvmet_fc_tgt_q_get(queue)) {
-			rcu_read_unlock();
-			continue;
-		}
-		rcu_read_unlock();
-		nvmet_fc_delete_target_queue(queue);
-		nvmet_fc_tgt_q_put(queue);
+	/* ensure all in-flight I/Os have been processed */
+	for (i = NVMET_NR_QUEUES; i >= 0; i--) {
+		if (assoc->queues[i])
+			flush_workqueue(assoc->queues[i]->work_q);
 	}
 
 	dev_info(tgtport->dev,
 		"{%d:%d} Association deleted\n",
 		tgtport->fc_target_port.port_num, assoc->a_id);
-
-	nvmet_fc_tgt_a_put(assoc);
 }
 
 static struct nvmet_fc_tgt_assoc *
@@ -1414,6 +1428,7 @@
 	kref_init(&newrec->ref);
 	ida_init(&newrec->assoc_cnt);
 	newrec->max_sg_cnt = template->max_sgl_segments;
+	INIT_WORK(&newrec->put_work, nvmet_fc_put_tgtport_work);
 
 	ret = nvmet_fc_alloc_ls_iodlist(newrec);
 	if (ret) {
@@ -1491,9 +1506,8 @@
 	list_for_each_entry_rcu(assoc, &tgtport->assoc_list, a_list) {
 		if (!nvmet_fc_tgt_a_get(assoc))
 			continue;
-		if (!schedule_work(&assoc->del_work))
-			/* already deleting - release local reference */
-			nvmet_fc_tgt_a_put(assoc);
+		nvmet_fc_schedule_delete_assoc(assoc);
+		nvmet_fc_tgt_a_put(assoc);
 	}
 	rcu_read_unlock();
 }
@@ -1546,9 +1560,8 @@
 			continue;
 		assoc->hostport->invalid = 1;
 		noassoc = false;
-		if (!schedule_work(&assoc->del_work))
-			/* already deleting - release local reference */
-			nvmet_fc_tgt_a_put(assoc);
+		nvmet_fc_schedule_delete_assoc(assoc);
+		nvmet_fc_tgt_a_put(assoc);
 	}
 	spin_unlock_irqrestore(&tgtport->lock, flags);
 
@@ -1580,7 +1593,7 @@
 
 		rcu_read_lock();
 		list_for_each_entry_rcu(assoc, &tgtport->assoc_list, a_list) {
-			queue = rcu_dereference(assoc->queues[0]);
+			queue = assoc->queues[0];
 			if (queue && queue->nvme_sq.ctrl == ctrl) {
 				if (nvmet_fc_tgt_a_get(assoc))
 					found_ctrl = true;
@@ -1592,9 +1605,8 @@
 		nvmet_fc_tgtport_put(tgtport);
 
 		if (found_ctrl) {
-			if (!schedule_work(&assoc->del_work))
-				/* already deleting - release local reference */
-				nvmet_fc_tgt_a_put(assoc);
+			nvmet_fc_schedule_delete_assoc(assoc);
+			nvmet_fc_tgt_a_put(assoc);
 			return;
 		}
 
@@ -1624,6 +1636,8 @@
 	/* terminate any outstanding associations */
 	__nvmet_fc_free_assocs(tgtport);
 
+	flush_workqueue(nvmet_wq);
+
 	/*
 	 * should terminate LS's as well. However, LS's will be generated
 	 * at the tail end of association termination, so they likely don't
@@ -1685,8 +1699,10 @@
 		else {
 			queue = nvmet_fc_alloc_target_queue(iod->assoc, 0,
 					be16_to_cpu(rqst->assoc_cmd.sqsize));
-			if (!queue)
+			if (!queue) {
 				ret = VERR_QUEUE_ALLOC_FAIL;
+				nvmet_fc_tgt_a_put(iod->assoc);
+			}
 		}
 	}
 
@@ -1867,9 +1883,6 @@
 				sizeof(struct fcnvme_ls_disconnect_assoc_acc)),
 			FCNVME_LS_DISCONNECT_ASSOC);
 
-	/* release get taken in nvmet_fc_find_target_assoc */
-	nvmet_fc_tgt_a_put(assoc);
-
 	/*
 	 * The rules for LS response says the response cannot
 	 * go back until ABTS's have been sent for all outstanding
@@ -1884,8 +1897,6 @@
 	assoc->rcv_disconn = iod;
 	spin_unlock_irqrestore(&tgtport->lock, flags);
 
-	nvmet_fc_delete_target_assoc(assoc);
-
 	if (oldls) {
 		dev_info(tgtport->dev,
 			"{%d:%d} Multiple Disconnect Association LS's "
@@ -1901,6 +1912,9 @@
 		nvmet_fc_xmt_ls_rsp(tgtport, oldls);
 	}
 
+	nvmet_fc_schedule_delete_assoc(assoc);
+	nvmet_fc_tgt_a_put(assoc);
+
 	return false;
 }
 
@@ -2060,7 +2074,7 @@
 	iod->rqstdatalen = lsreqbuf_len;
 	iod->hosthandle = hosthandle;
 
-	schedule_work(&iod->work);
+	queue_work(nvmet_wq, &iod->work);
 
 	return 0;
 }
@@ -2537,8 +2551,9 @@
 
 	fod->req.cmd = &fod->cmdiubuf.sqe;
 	fod->req.cqe = &fod->rspiubuf.cqe;
-	if (tgtport->pe)
-		fod->req.port = tgtport->pe->port;
+	if (!tgtport->pe)
+		goto transport_error;
+	fod->req.port = tgtport->pe->port;
 
 	/* clear any response payload */
 	memset(&fod->rspiubuf, 0, sizeof(fod->rspiubuf));
@@ -2899,6 +2914,9 @@
 
 	nvmet_fc_portentry_unbind(pe);
 
+	/* terminate any outstanding associations */
+	__nvmet_fc_free_assocs(pe->tgtport);
+
 	kfree(pe);
 }
 
@@ -2930,6 +2948,9 @@
 
 static void __exit nvmet_fc_exit_module(void)
 {
+	/* ensure any shutdown operation, e.g. delete ctrls have finished */
+	flush_workqueue(nvmet_wq);
+
 	/* sanity check - all lports should be removed */
 	if (!list_empty(&nvmet_fc_target_list))
 		pr_warn("%s: targetport list not empty\n", __func__);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/fcloop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/fcloop.c
@@ -358,9 +358,9 @@
 	if (!rport->targetport) {
 		tls_req->status = -ECONNREFUSED;
 		spin_lock(&rport->lock);
-		list_add_tail(&rport->ls_list, &tls_req->ls_list);
+		list_add_tail(&tls_req->ls_list, &rport->ls_list);
 		spin_unlock(&rport->lock);
-		schedule_work(&rport->ls_work);
+		queue_work(nvmet_wq, &rport->ls_work);
 		return ret;
 	}
 
@@ -391,9 +391,9 @@
 	if (remoteport) {
 		rport = remoteport->private;
 		spin_lock(&rport->lock);
-		list_add_tail(&rport->ls_list, &tls_req->ls_list);
+		list_add_tail(&tls_req->ls_list, &rport->ls_list);
 		spin_unlock(&rport->lock);
-		schedule_work(&rport->ls_work);
+		queue_work(nvmet_wq, &rport->ls_work);
 	}
 
 	return 0;
@@ -446,9 +446,9 @@
 	if (!tport->remoteport) {
 		tls_req->status = -ECONNREFUSED;
 		spin_lock(&tport->lock);
-		list_add_tail(&tport->ls_list, &tls_req->ls_list);
+		list_add_tail(&tls_req->ls_list, &tport->ls_list);
 		spin_unlock(&tport->lock);
-		schedule_work(&tport->ls_work);
+		queue_work(nvmet_wq, &tport->ls_work);
 		return ret;
 	}
 
@@ -480,7 +480,7 @@
 		spin_lock(&tport->lock);
 		list_add_tail(&tport->ls_list, &tls_req->ls_list);
 		spin_unlock(&tport->lock);
-		schedule_work(&tport->ls_work);
+		queue_work(nvmet_wq, &tport->ls_work);
 	}
 
 	return 0;
@@ -520,7 +520,7 @@
 	tgt_rscn->tport = tgtport->private;
 	INIT_WORK(&tgt_rscn->work, fcloop_tgt_rscn_work);
 
-	schedule_work(&tgt_rscn->work);
+	queue_work(nvmet_wq, &tgt_rscn->work);
 }
 
 static void
@@ -614,10 +614,11 @@
 	struct fcloop_fcpreq *tfcp_req =
 		container_of(work, struct fcloop_fcpreq, fcp_rcv_work);
 	struct nvmefc_fcp_req *fcpreq = tfcp_req->fcpreq;
+	unsigned long flags;
 	int ret = 0;
 	bool aborted = false;
 
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	switch (tfcp_req->inistate) {
 	case INI_IO_START:
 		tfcp_req->inistate = INI_IO_ACTIVE;
@@ -626,11 +627,11 @@
 		aborted = true;
 		break;
 	default:
-		spin_unlock_irq(&tfcp_req->reqlock);
+		spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 		WARN_ON(1);
 		return;
 	}
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	if (unlikely(aborted))
 		ret = -ECANCELED;
@@ -655,8 +656,9 @@
 		container_of(work, struct fcloop_fcpreq, abort_rcv_work);
 	struct nvmefc_fcp_req *fcpreq;
 	bool completed = false;
+	unsigned long flags;
 
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	fcpreq = tfcp_req->fcpreq;
 	switch (tfcp_req->inistate) {
 	case INI_IO_ABORTED:
@@ -665,11 +667,11 @@
 		completed = true;
 		break;
 	default:
-		spin_unlock_irq(&tfcp_req->reqlock);
+		spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 		WARN_ON(1);
 		return;
 	}
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	if (unlikely(completed)) {
 		/* remove reference taken in original abort downcall */
@@ -681,9 +683,9 @@
 		nvmet_fc_rcv_fcp_abort(tfcp_req->tport->targetport,
 					&tfcp_req->tgt_fcp_req);
 
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	tfcp_req->fcpreq = NULL;
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	fcloop_call_host_done(fcpreq, tfcp_req, -ECANCELED);
 	/* call_host_done releases reference for abort downcall */
@@ -699,11 +701,12 @@
 	struct fcloop_fcpreq *tfcp_req =
 		container_of(work, struct fcloop_fcpreq, tio_done_work);
 	struct nvmefc_fcp_req *fcpreq;
+	unsigned long flags;
 
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	fcpreq = tfcp_req->fcpreq;
 	tfcp_req->inistate = INI_IO_COMPLETED;
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	fcloop_call_host_done(fcpreq, tfcp_req, tfcp_req->status);
 }
@@ -739,7 +742,7 @@
 	INIT_WORK(&tfcp_req->tio_done_work, fcloop_tgt_fcprqst_done_work);
 	kref_init(&tfcp_req->ref);
 
-	schedule_work(&tfcp_req->fcp_rcv_work);
+	queue_work(nvmet_wq, &tfcp_req->fcp_rcv_work);
 
 	return 0;
 }
@@ -807,13 +810,14 @@
 	u32 rsplen = 0, xfrlen = 0;
 	int fcp_err = 0, active, aborted;
 	u8 op = tgt_fcpreq->op;
+	unsigned long flags;
 
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	fcpreq = tfcp_req->fcpreq;
 	active = tfcp_req->active;
 	aborted = tfcp_req->aborted;
 	tfcp_req->active = true;
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	if (unlikely(active))
 		/* illegal - call while i/o active */
@@ -821,9 +825,9 @@
 
 	if (unlikely(aborted)) {
 		/* target transport has aborted i/o prior */
-		spin_lock_irq(&tfcp_req->reqlock);
+		spin_lock_irqsave(&tfcp_req->reqlock, flags);
 		tfcp_req->active = false;
-		spin_unlock_irq(&tfcp_req->reqlock);
+		spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 		tgt_fcpreq->transferred_length = 0;
 		tgt_fcpreq->fcp_error = -ECANCELED;
 		tgt_fcpreq->done(tgt_fcpreq);
@@ -880,9 +884,9 @@
 		break;
 	}
 
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	tfcp_req->active = false;
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	tgt_fcpreq->transferred_length = xfrlen;
 	tgt_fcpreq->fcp_error = fcp_err;
@@ -896,15 +900,16 @@
 			struct nvmefc_tgt_fcp_req *tgt_fcpreq)
 {
 	struct fcloop_fcpreq *tfcp_req = tgt_fcp_req_to_fcpreq(tgt_fcpreq);
+	unsigned long flags;
 
 	/*
 	 * mark aborted only in case there were 2 threads in transport
 	 * (one doing io, other doing abort) and only kills ops posted
 	 * after the abort request
 	 */
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	tfcp_req->aborted = true;
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	tfcp_req->status = NVME_SC_INTERNAL;
 
@@ -921,7 +926,7 @@
 {
 	struct fcloop_fcpreq *tfcp_req = tgt_fcp_req_to_fcpreq(tgt_fcpreq);
 
-	schedule_work(&tfcp_req->tio_done_work);
+	queue_work(nvmet_wq, &tfcp_req->tio_done_work);
 }
 
 static void
@@ -946,6 +951,7 @@
 	struct fcloop_ini_fcpreq *inireq = fcpreq->private;
 	struct fcloop_fcpreq *tfcp_req;
 	bool abortio = true;
+	unsigned long flags;
 
 	spin_lock(&inireq->inilock);
 	tfcp_req = inireq->tfcp_req;
@@ -958,7 +964,7 @@
 		return;
 
 	/* break initiator/target relationship for io */
-	spin_lock_irq(&tfcp_req->reqlock);
+	spin_lock_irqsave(&tfcp_req->reqlock, flags);
 	switch (tfcp_req->inistate) {
 	case INI_IO_START:
 	case INI_IO_ACTIVE:
@@ -968,15 +974,15 @@
 		abortio = false;
 		break;
 	default:
-		spin_unlock_irq(&tfcp_req->reqlock);
+		spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 		WARN_ON(1);
 		return;
 	}
-	spin_unlock_irq(&tfcp_req->reqlock);
+	spin_unlock_irqrestore(&tfcp_req->reqlock, flags);
 
 	if (abortio)
 		/* leave the reference while the work item is scheduled */
-		WARN_ON(!schedule_work(&tfcp_req->abort_rcv_work));
+		WARN_ON(!queue_work(nvmet_wq, &tfcp_req->abort_rcv_work));
 	else  {
 		/*
 		 * as the io has already had the done callback made,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/io-cmd-bdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/io-cmd-bdev.c
@@ -36,7 +36,7 @@
 	 */
 	id->nsfeat |= 1 << 4;
 	/* NPWG = Namespace Preferred Write Granularity. 0's based */
-	id->npwg = lpp0b;
+	id->npwg = to0based(bdev_io_min(bdev) / bdev_logical_block_size(bdev));
 	/* NPWA = Namespace Preferred Write Alignment. 0's based */
 	id->npwa = id->npwg;
 	/* NPDG = Namespace Preferred Deallocate Granularity. 0's based */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/io-cmd-file.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/io-cmd-file.c
@@ -8,21 +8,14 @@
 #include <linux/uio.h>
 #include <linux/falloc.h>
 #include <linux/file.h>
+#include <linux/fs.h>
 #include "nvmet.h"
 
-#define NVMET_MAX_MPOOL_BVEC		16
 #define NVMET_MIN_MPOOL_OBJ		16
 
-int nvmet_file_ns_revalidate(struct nvmet_ns *ns)
+void nvmet_file_ns_revalidate(struct nvmet_ns *ns)
 {
-	struct kstat stat;
-	int ret;
-
-	ret = vfs_getattr(&ns->file->f_path, &stat, STATX_SIZE,
-			  AT_STATX_FORCE_SYNC);
-	if (!ret)
-		ns->size = stat.size;
-	return ret;
+	ns->size = i_size_read(ns->file->f_mapping->host);
 }
 
 void nvmet_file_ns_disable(struct nvmet_ns *ns)
@@ -32,8 +25,6 @@
 			flush_workqueue(buffered_io_wq);
 		mempool_destroy(ns->bvec_pool);
 		ns->bvec_pool = NULL;
-		kmem_cache_destroy(ns->bvec_cache);
-		ns->bvec_cache = NULL;
 		fput(ns->file);
 		ns->file = NULL;
 	}
@@ -42,7 +33,7 @@
 int nvmet_file_ns_enable(struct nvmet_ns *ns)
 {
 	int flags = O_RDWR | O_LARGEFILE;
-	int ret;
+	int ret = 0;
 
 	if (!ns->buffered_io)
 		flags |= O_DIRECT;
@@ -56,9 +47,7 @@
 		return ret;
 	}
 
-	ret = nvmet_file_ns_revalidate(ns);
-	if (ret)
-		goto err;
+	nvmet_file_ns_revalidate(ns);
 
 	/*
 	 * i_blkbits can be greater than the universally accepted upper bound,
@@ -67,16 +56,8 @@
 	ns->blksize_shift = min_t(u8,
 			file_inode(ns->file)->i_blkbits, 12);
 
-	ns->bvec_cache = kmem_cache_create("nvmet-bvec",
-			NVMET_MAX_MPOOL_BVEC * sizeof(struct bio_vec),
-			0, SLAB_HWCACHE_ALIGN, NULL);
-	if (!ns->bvec_cache) {
-		ret = -ENOMEM;
-		goto err;
-	}
-
 	ns->bvec_pool = mempool_create(NVMET_MIN_MPOOL_OBJ, mempool_alloc_slab,
-			mempool_free_slab, ns->bvec_cache);
+			mempool_free_slab, nvmet_bvec_cache);
 
 	if (!ns->bvec_pool) {
 		ret = -ENOMEM;
@@ -85,9 +66,10 @@
 
 	return ret;
 err:
+	fput(ns->file);
+	ns->file = NULL;
 	ns->size = 0;
 	ns->blksize_shift = 0;
-	nvmet_file_ns_disable(ns);
 	return ret;
 }
 
@@ -266,7 +248,8 @@
 
 	if (req->ns->buffered_io) {
 		if (likely(!req->f.mpool_alloc) &&
-				nvmet_file_execute_io(req, IOCB_NOWAIT))
+		    (req->ns->file->f_mode & FMODE_NOWAIT) &&
+		    nvmet_file_execute_io(req, IOCB_NOWAIT))
 			return;
 		nvmet_file_submit_buffered_io(req);
 	} else
@@ -290,7 +273,7 @@
 	if (!nvmet_check_transfer_len(req, 0))
 		return;
 	INIT_WORK(&req->f.work, nvmet_file_flush_work);
-	schedule_work(&req->f.work);
+	queue_work(nvmet_wq, &req->f.work);
 }
 
 static void nvmet_file_execute_discard(struct nvmet_req *req)
@@ -350,7 +333,7 @@
 	if (!nvmet_check_data_len_lte(req, nvmet_dsm_len(req)))
 		return;
 	INIT_WORK(&req->f.work, nvmet_file_dsm_work);
-	schedule_work(&req->f.work);
+	queue_work(nvmet_wq, &req->f.work);
 }
 
 static void nvmet_file_write_zeroes_work(struct work_struct *w)
@@ -380,7 +363,7 @@
 	if (!nvmet_check_transfer_len(req, 0))
 		return;
 	INIT_WORK(&req->f.work, nvmet_file_write_zeroes_work);
-	schedule_work(&req->f.work);
+	queue_work(nvmet_wq, &req->f.work);
 }
 
 u16 nvmet_file_parse_io_cmd(struct nvmet_req *req)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/loop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/loop.c
@@ -166,7 +166,7 @@
 		iod->req.transfer_len = blk_rq_payload_bytes(req);
 	}
 
-	schedule_work(&iod->work);
+	queue_work(nvmet_wq, &iod->work);
 	return BLK_STS_OK;
 }
 
@@ -187,7 +187,7 @@
 		return;
 	}
 
-	schedule_work(&iod->work);
+	queue_work(nvmet_wq, &iod->work);
 }
 
 static int nvme_loop_init_iod(struct nvme_loop_ctrl *ctrl,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/nvmet.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/nvmet.h
@@ -77,7 +77,6 @@
 
 	struct completion	disable_done;
 	mempool_t		*bvec_pool;
-	struct kmem_cache	*bvec_cache;
 
 	int			use_p2pmem;
 	struct pci_dev		*p2p_dev;
@@ -363,8 +362,11 @@
 	u64			error_slba;
 };
 
+#define NVMET_MAX_MPOOL_BVEC		16
+extern struct kmem_cache *nvmet_bvec_cache;
 extern struct workqueue_struct *buffered_io_wq;
 extern struct workqueue_struct *zbd_wq;
+extern struct workqueue_struct *nvmet_wq;
 
 static inline void nvmet_set_result(struct nvmet_req *req, u32 result)
 {
@@ -540,12 +542,12 @@
 u16 nvmet_file_flush(struct nvmet_req *req);
 void nvmet_ns_changed(struct nvmet_subsys *subsys, u32 nsid);
 void nvmet_bdev_ns_revalidate(struct nvmet_ns *ns);
-int nvmet_file_ns_revalidate(struct nvmet_ns *ns);
-void nvmet_ns_revalidate(struct nvmet_ns *ns);
+void nvmet_file_ns_revalidate(struct nvmet_ns *ns);
+bool nvmet_ns_revalidate(struct nvmet_ns *ns);
 u16 blk_to_nvme_status(struct nvmet_req *req, blk_status_t blk_sts);
 
 bool nvmet_bdev_zns_enable(struct nvmet_ns *ns);
-void nvmet_execute_identify_cns_cs_ctrl(struct nvmet_req *req);
+void nvmet_execute_identify_ctrl_zns(struct nvmet_req *req);
 void nvmet_execute_identify_cns_cs_ns(struct nvmet_req *req);
 void nvmet_bdev_execute_zone_mgmt_recv(struct nvmet_req *req);
 void nvmet_bdev_execute_zone_mgmt_send(struct nvmet_req *req);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/passthru.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/passthru.c
@@ -271,17 +271,16 @@
 	}
 
 	/*
-	 * If there are effects for the command we are about to execute, or
-	 * an end_req function we need to use nvme_execute_passthru_rq()
-	 * synchronously in a work item seeing the end_req function and
-	 * nvme_passthru_end() can't be called in the request done callback
-	 * which is typically in interrupt context.
+	 * If a command needs post-execution fixups, or there are any
+	 * non-trivial effects, make sure to execute the command synchronously
+	 * in a workqueue so that nvme_passthru_end gets called.
 	 */
 	effects = nvme_command_effects(ctrl, ns, req->cmd->common.opcode);
-	if (req->p.use_workqueue || effects) {
+	if (req->p.use_workqueue ||
+	    (effects & ~(NVME_CMD_EFFECTS_CSUPP | NVME_CMD_EFFECTS_LBCC))) {
 		INIT_WORK(&req->p.work, nvmet_passthru_execute_cmd_work);
 		req->p.rq = rq;
-		schedule_work(&req->p.work);
+		queue_work(nvmet_wq, &req->p.work);
 	} else {
 		rq->end_io_data = req;
 		blk_execute_rq_nowait(ns ? ns->disk : NULL, rq, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/rdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/rdma.c
@@ -472,12 +472,8 @@
 	return 0;
 
 out_free:
-	while (--i >= 0) {
-		struct nvmet_rdma_rsp *rsp = &queue->rsps[i];
-
-		list_del(&rsp->free_list);
-		nvmet_rdma_free_rsp(ndev, rsp);
-	}
+	while (--i >= 0)
+		nvmet_rdma_free_rsp(ndev, &queue->rsps[i]);
 	kfree(queue->rsps);
 out:
 	return ret;
@@ -488,12 +484,8 @@
 	struct nvmet_rdma_device *ndev = queue->dev;
 	int i, nr_rsps = queue->recv_queue_size * 2;
 
-	for (i = 0; i < nr_rsps; i++) {
-		struct nvmet_rdma_rsp *rsp = &queue->rsps[i];
-
-		list_del(&rsp->free_list);
-		nvmet_rdma_free_rsp(ndev, rsp);
-	}
+	for (i = 0; i < nr_rsps; i++)
+		nvmet_rdma_free_rsp(ndev, &queue->rsps[i]);
 	kfree(queue->rsps);
 }
 
@@ -1004,6 +996,27 @@
 	nvmet_req_complete(&cmd->req, status);
 }
 
+static bool nvmet_rdma_recv_not_live(struct nvmet_rdma_queue *queue,
+		struct nvmet_rdma_rsp *rsp)
+{
+	unsigned long flags;
+	bool ret = true;
+
+	spin_lock_irqsave(&queue->state_lock, flags);
+	/*
+	 * recheck queue state is not live to prevent a race condition
+	 * with RDMA_CM_EVENT_ESTABLISHED handler.
+	 */
+	if (queue->state == NVMET_RDMA_Q_LIVE)
+		ret = false;
+	else if (queue->state == NVMET_RDMA_Q_CONNECTING)
+		list_add_tail(&rsp->wait_list, &queue->rsp_wait_list);
+	else
+		nvmet_rdma_put_rsp(rsp);
+	spin_unlock_irqrestore(&queue->state_lock, flags);
+	return ret;
+}
+
 static void nvmet_rdma_recv_done(struct ib_cq *cq, struct ib_wc *wc)
 {
 	struct nvmet_rdma_cmd *cmd =
@@ -1045,17 +1058,9 @@
 	rsp->req.port = queue->port;
 	rsp->n_rdma = 0;
 
-	if (unlikely(queue->state != NVMET_RDMA_Q_LIVE)) {
-		unsigned long flags;
-
-		spin_lock_irqsave(&queue->state_lock, flags);
-		if (queue->state == NVMET_RDMA_Q_CONNECTING)
-			list_add_tail(&rsp->wait_list, &queue->rsp_wait_list);
-		else
-			nvmet_rdma_put_rsp(rsp);
-		spin_unlock_irqrestore(&queue->state_lock, flags);
+	if (unlikely(queue->state != NVMET_RDMA_Q_LIVE) &&
+	    nvmet_rdma_recv_not_live(queue, rsp))
 		return;
-	}
 
 	nvmet_rdma_handle_command(queue, rsp);
 }
@@ -1583,7 +1588,7 @@
 
 	if (queue->host_qid == 0) {
 		/* Let inflight controller teardown complete */
-		flush_scheduled_work();
+		flush_workqueue(nvmet_wq);
 	}
 
 	ret = nvmet_rdma_cm_accept(cm_id, queue, &event->param.conn);
@@ -1668,7 +1673,7 @@
 
 	if (disconnect) {
 		rdma_disconnect(queue->cm_id);
-		schedule_work(&queue->release_work);
+		queue_work(nvmet_wq, &queue->release_work);
 	}
 }
 
@@ -1698,7 +1703,7 @@
 	mutex_unlock(&nvmet_rdma_queue_mutex);
 
 	pr_err("failed to connect queue %d\n", queue->idx);
-	schedule_work(&queue->release_work);
+	queue_work(nvmet_wq, &queue->release_work);
 }
 
 /**
@@ -1772,7 +1777,7 @@
 		if (!queue) {
 			struct nvmet_rdma_port *port = cm_id->context;
 
-			schedule_delayed_work(&port->repair_work, 0);
+			queue_delayed_work(nvmet_wq, &port->repair_work, 0);
 			break;
 		}
 		fallthrough;
@@ -1818,12 +1823,36 @@
 	mutex_unlock(&nvmet_rdma_queue_mutex);
 }
 
+static void nvmet_rdma_destroy_port_queues(struct nvmet_rdma_port *port)
+{
+	struct nvmet_rdma_queue *queue, *tmp;
+	struct nvmet_port *nport = port->nport;
+
+	mutex_lock(&nvmet_rdma_queue_mutex);
+	list_for_each_entry_safe(queue, tmp, &nvmet_rdma_queue_list,
+				 queue_list) {
+		if (queue->port != nport)
+			continue;
+
+		list_del_init(&queue->queue_list);
+		__nvmet_rdma_queue_disconnect(queue);
+	}
+	mutex_unlock(&nvmet_rdma_queue_mutex);
+}
+
 static void nvmet_rdma_disable_port(struct nvmet_rdma_port *port)
 {
 	struct rdma_cm_id *cm_id = xchg(&port->cm_id, NULL);
 
 	if (cm_id)
 		rdma_destroy_id(cm_id);
+
+	/*
+	 * Destroy the remaining queues, which are not belong to any
+	 * controller yet. Do it here after the RDMA-CM was destroyed
+	 * guarantees that no new queue will be created.
+	 */
+	nvmet_rdma_destroy_port_queues(port);
 }
 
 static int nvmet_rdma_enable_port(struct nvmet_rdma_port *port)
@@ -1878,7 +1907,7 @@
 	nvmet_rdma_disable_port(port);
 	ret = nvmet_rdma_enable_port(port);
 	if (ret)
-		schedule_delayed_work(&port->repair_work, 5 * HZ);
+		queue_delayed_work(nvmet_wq, &port->repair_work, 5 * HZ);
 }
 
 static int nvmet_rdma_add_port(struct nvmet_port *nport)
@@ -2022,7 +2051,7 @@
 	}
 	mutex_unlock(&nvmet_rdma_queue_mutex);
 
-	flush_scheduled_work();
+	flush_workqueue(nvmet_wq);
 }
 
 static struct ib_client nvmet_rdma_ib_client = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/tcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/tcp.c
@@ -18,6 +18,7 @@
 #include "nvmet.h"
 
 #define NVMET_TCP_DEF_INLINE_DATA_SIZE	(4 * PAGE_SIZE)
+#define NVMET_TCP_MAXH2CDATA		0x400000 /* 16M arbitrary limit */
 
 /* Define the socket priority to use for connections were it is desirable
  * that the NIC consider performing optimized packet processing or filtering.
@@ -348,6 +349,7 @@
 
 static void nvmet_tcp_socket_error(struct nvmet_tcp_queue *queue, int status)
 {
+	queue->rcv_state = NVMET_TCP_RECV_ERR;
 	if (status == -EPIPE || status == -ECONNRESET)
 		kernel_sock_shutdown(queue->sock, SHUT_RDWR);
 	else
@@ -537,10 +539,16 @@
 	struct nvmet_tcp_cmd *cmd =
 		container_of(req, struct nvmet_tcp_cmd, req);
 	struct nvmet_tcp_queue	*queue = cmd->queue;
+	enum nvmet_tcp_recv_state queue_state;
+	struct nvmet_tcp_cmd *queue_cmd;
 	struct nvme_sgl_desc *sgl;
 	u32 len;
 
-	if (unlikely(cmd == queue->cmd)) {
+	/* Pairs with store_release in nvmet_prepare_receive_pdu() */
+	queue_state = smp_load_acquire(&queue->rcv_state);
+	queue_cmd = READ_ONCE(queue->cmd);
+
+	if (unlikely(cmd == queue_cmd)) {
 		sgl = &cmd->req.cmd->common.dptr.sgl;
 		len = le32_to_cpu(sgl->length);
 
@@ -549,7 +557,7 @@
 		 * Avoid using helpers, this might happen before
 		 * nvmet_req_init is completed.
 		 */
-		if (queue->rcv_state == NVMET_TCP_RECV_PDU &&
+		if (queue_state == NVMET_TCP_RECV_PDU &&
 		    len && len <= cmd->req.port->inline_data_size &&
 		    nvme_is_write(cmd->req.cmd))
 			return;
@@ -700,10 +708,11 @@
 static int nvmet_try_send_ddgst(struct nvmet_tcp_cmd *cmd, bool last_in_batch)
 {
 	struct nvmet_tcp_queue *queue = cmd->queue;
+	int left = NVME_TCP_DIGEST_LENGTH - cmd->offset;
 	struct msghdr msg = { .msg_flags = MSG_DONTWAIT };
 	struct kvec iov = {
 		.iov_base = (u8 *)&cmd->exp_ddgst + cmd->offset,
-		.iov_len = NVME_TCP_DIGEST_LENGTH - cmd->offset
+		.iov_len = left
 	};
 	int ret;
 
@@ -717,6 +726,10 @@
 		return ret;
 
 	cmd->offset += ret;
+	left -= ret;
+
+	if (left)
+		return -EAGAIN;
 
 	if (queue->nvme_sq.sqhd_disabled) {
 		cmd->queue->snd_cmd = NULL;
@@ -799,8 +812,9 @@
 {
 	queue->offset = 0;
 	queue->left = sizeof(struct nvme_tcp_hdr);
-	queue->cmd = NULL;
-	queue->rcv_state = NVMET_TCP_RECV_PDU;
+	WRITE_ONCE(queue->cmd, NULL);
+	/* Ensure rcv_state is visible only after queue->cmd is set */
+	smp_store_release(&queue->rcv_state, NVMET_TCP_RECV_PDU);
 }
 
 static void nvmet_tcp_free_crypto(struct nvmet_tcp_queue *queue)
@@ -851,6 +865,7 @@
 		pr_err("bad nvme-tcp pdu length (%d)\n",
 			le32_to_cpu(icreq->hdr.plen));
 		nvmet_tcp_fatal_error(queue);
+		return -EPROTO;
 	}
 
 	if (icreq->pfv != NVME_TCP_PFV_1_0) {
@@ -878,7 +893,7 @@
 	icresp->hdr.pdo = 0;
 	icresp->hdr.plen = cpu_to_le32(icresp->hdr.hlen);
 	icresp->pfv = cpu_to_le16(NVME_TCP_PFV_1_0);
-	icresp->maxdata = cpu_to_le32(0x400000); /* 16M arbitrary limit */
+	icresp->maxdata = cpu_to_le32(NVMET_TCP_MAXH2CDATA);
 	icresp->cpda = 0;
 	if (queue->hdr_digest)
 		icresp->digest |= NVME_TCP_HDR_DIGEST_ENABLE;
@@ -889,15 +904,11 @@
 	iov.iov_len = sizeof(*icresp);
 	ret = kernel_sendmsg(queue->sock, &msg, &iov, 1, iov.iov_len);
 	if (ret < 0)
-		goto free_crypto;
+		return ret; /* queue removal will cleanup */
 
 	queue->state = NVMET_TCP_Q_LIVE;
 	nvmet_prepare_receive_pdu(queue);
 	return 0;
-free_crypto:
-	if (queue->hdr_digest || queue->data_digest)
-		nvmet_tcp_free_crypto(queue);
-	return ret;
 }
 
 static void nvmet_tcp_handle_req_failure(struct nvmet_tcp_queue *queue,
@@ -928,23 +939,43 @@
 {
 	struct nvme_tcp_data_pdu *data = &queue->pdu.data;
 	struct nvmet_tcp_cmd *cmd;
+	unsigned int exp_data_len;
 
-	if (likely(queue->nr_cmds))
+	if (likely(queue->nr_cmds)) {
+		if (unlikely(data->ttag >= queue->nr_cmds)) {
+			pr_err("queue %d: received out of bound ttag %u, nr_cmds %u\n",
+				queue->idx, data->ttag, queue->nr_cmds);
+			nvmet_tcp_fatal_error(queue);
+			return -EPROTO;
+		}
 		cmd = &queue->cmds[data->ttag];
-	else
+	} else {
 		cmd = &queue->connect;
+	}
 
 	if (le32_to_cpu(data->data_offset) != cmd->rbytes_done) {
 		pr_err("ttag %u unexpected data offset %u (expected %u)\n",
 			data->ttag, le32_to_cpu(data->data_offset),
 			cmd->rbytes_done);
 		/* FIXME: use path and transport errors */
-		nvmet_req_complete(&cmd->req,
-			NVME_SC_INVALID_FIELD | NVME_SC_DNR);
+		nvmet_tcp_fatal_error(queue);
 		return -EPROTO;
 	}
 
+	exp_data_len = le32_to_cpu(data->hdr.plen) -
+			nvmet_tcp_hdgst_len(queue) -
+			nvmet_tcp_ddgst_len(queue) -
+			sizeof(*data);
+
 	cmd->pdu_len = le32_to_cpu(data->data_length);
+	if (unlikely(cmd->pdu_len != exp_data_len ||
+		     cmd->pdu_len == 0 ||
+		     cmd->pdu_len > NVMET_TCP_MAXH2CDATA)) {
+		pr_err("H2CData PDU len %u is invalid\n", cmd->pdu_len);
+		/* FIXME: use proper transport errors */
+		nvmet_tcp_fatal_error(queue);
+		return -EPROTO;
+	}
 	cmd->pdu_recv = 0;
 	nvmet_tcp_map_pdu_iovec(cmd);
 	queue->cmd = cmd;
@@ -1246,7 +1277,7 @@
 	spin_lock(&queue->state_lock);
 	if (queue->state != NVMET_TCP_Q_DISCONNECTING) {
 		queue->state = NVMET_TCP_Q_DISCONNECTING;
-		schedule_work(&queue->release_work);
+		queue_work(nvmet_wq, &queue->release_work);
 	}
 	spin_unlock(&queue->state_lock);
 }
@@ -1496,6 +1527,9 @@
 		goto done;
 
 	switch (sk->sk_state) {
+	case TCP_FIN_WAIT2:
+	case TCP_LAST_ACK:
+		break;
 	case TCP_FIN_WAIT1:
 	case TCP_CLOSE_WAIT:
 	case TCP_CLOSE:
@@ -1657,7 +1691,7 @@
 		goto out;
 
 	if (sk->sk_state == TCP_LISTEN)
-		schedule_work(&port->accept_work);
+		queue_work(nvmet_wq, &port->accept_work);
 out:
 	read_unlock_bh(&sk->sk_callback_lock);
 }
@@ -1740,6 +1774,17 @@
 	return ret;
 }
 
+static void nvmet_tcp_destroy_port_queues(struct nvmet_tcp_port *port)
+{
+	struct nvmet_tcp_queue *queue;
+
+	mutex_lock(&nvmet_tcp_queue_mutex);
+	list_for_each_entry(queue, &nvmet_tcp_queue_list, queue_list)
+		if (queue->port == port)
+			kernel_sock_shutdown(queue->sock, SHUT_RDWR);
+	mutex_unlock(&nvmet_tcp_queue_mutex);
+}
+
 static void nvmet_tcp_remove_port(struct nvmet_port *nport)
 {
 	struct nvmet_tcp_port *port = nport->priv;
@@ -1749,6 +1794,11 @@
 	port->sock->sk->sk_user_data = NULL;
 	write_unlock_bh(&port->sock->sk->sk_callback_lock);
 	cancel_work_sync(&port->accept_work);
+	/*
+	 * Destroy the remaining queues, which are not belong to any
+	 * controller yet.
+	 */
+	nvmet_tcp_destroy_port_queues(port);
 
 	sock_release(port->sock);
 	kfree(port);
@@ -1772,12 +1822,14 @@
 
 	if (sq->qid == 0) {
 		/* Let inflight controller teardown complete */
-		flush_scheduled_work();
+		flush_workqueue(nvmet_wq);
 	}
 
 	queue->nr_cmds = sq->size * 2;
-	if (nvmet_tcp_alloc_cmds(queue))
+	if (nvmet_tcp_alloc_cmds(queue)) {
+		queue->nr_cmds = 0;
 		return NVME_SC_INTERNAL;
+	}
 	return 0;
 }
 
@@ -1813,7 +1865,8 @@
 {
 	int ret;
 
-	nvmet_tcp_wq = alloc_workqueue("nvmet_tcp_wq", WQ_HIGHPRI, 0);
+	nvmet_tcp_wq = alloc_workqueue("nvmet_tcp_wq",
+				WQ_MEM_RECLAIM | WQ_HIGHPRI, 0);
 	if (!nvmet_tcp_wq)
 		return -ENOMEM;
 
@@ -1833,14 +1886,15 @@
 
 	nvmet_unregister_transport(&nvmet_tcp_ops);
 
-	flush_scheduled_work();
+	flush_workqueue(nvmet_wq);
 	mutex_lock(&nvmet_tcp_queue_mutex);
 	list_for_each_entry(queue, &nvmet_tcp_queue_list, queue_list)
 		kernel_sock_shutdown(queue->sock, SHUT_RDWR);
 	mutex_unlock(&nvmet_tcp_queue_mutex);
-	flush_scheduled_work();
+	flush_workqueue(nvmet_wq);
 
 	destroy_workqueue(nvmet_tcp_wq);
+	ida_destroy(&nvmet_tcp_queue_ida);
 }
 
 module_init(nvmet_tcp_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/trace.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/trace.c
@@ -211,7 +211,7 @@
 	return ret;
 }
 
-const char *nvmet_trace_ctrl_name(struct trace_seq *p, struct nvmet_ctrl *ctrl)
+const char *nvmet_trace_ctrl_id(struct trace_seq *p, u16 ctrl_id)
 {
 	const char *ret = trace_seq_buffer_ptr(p);
 
@@ -224,8 +224,8 @@
 	 * If we can know the extra data of the connect command in this stage,
 	 * we can update this print statement later.
 	 */
-	if (ctrl)
-		trace_seq_printf(p, "%d", ctrl->cntlid);
+	if (ctrl_id)
+		trace_seq_printf(p, "%d", ctrl_id);
 	else
 		trace_seq_printf(p, "_");
 	trace_seq_putc(p, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/trace.h
@@ -32,18 +32,24 @@
 	 nvmet_trace_parse_nvm_cmd(p, opcode, cdw10) :			\
 	 nvmet_trace_parse_admin_cmd(p, opcode, cdw10)))
 
-const char *nvmet_trace_ctrl_name(struct trace_seq *p, struct nvmet_ctrl *ctrl);
-#define __print_ctrl_name(ctrl)				\
-	nvmet_trace_ctrl_name(p, ctrl)
+const char *nvmet_trace_ctrl_id(struct trace_seq *p, u16 ctrl_id);
+#define __print_ctrl_id(ctrl_id)			\
+	nvmet_trace_ctrl_id(p, ctrl_id)
 
 const char *nvmet_trace_disk_name(struct trace_seq *p, char *name);
 #define __print_disk_name(name)				\
 	nvmet_trace_disk_name(p, name)
 
 #ifndef TRACE_HEADER_MULTI_READ
-static inline struct nvmet_ctrl *nvmet_req_to_ctrl(struct nvmet_req *req)
+static inline u16 nvmet_req_to_ctrl_id(struct nvmet_req *req)
 {
-	return req->sq->ctrl;
+	/*
+	 * The queue and controller pointers are not valid until an association
+	 * has been established.
+	 */
+	if (!req->sq || !req->sq->ctrl)
+		return 0;
+	return req->sq->ctrl->cntlid;
 }
 
 static inline void __assign_req_name(char *name, struct nvmet_req *req)
@@ -53,8 +59,7 @@
 		return;
 	}
 
-	strncpy(name, req->ns->device_path,
-		min_t(size_t, DISK_NAME_LEN, strlen(req->ns->device_path)));
+	strscpy_pad(name, req->ns->device_path, DISK_NAME_LEN);
 }
 #endif
 
@@ -63,7 +68,7 @@
 	TP_ARGS(req, cmd),
 	TP_STRUCT__entry(
 		__field(struct nvme_command *, cmd)
-		__field(struct nvmet_ctrl *, ctrl)
+		__field(u16, ctrl_id)
 		__array(char, disk, DISK_NAME_LEN)
 		__field(int, qid)
 		__field(u16, cid)
@@ -76,7 +81,7 @@
 	),
 	TP_fast_assign(
 		__entry->cmd = cmd;
-		__entry->ctrl = nvmet_req_to_ctrl(req);
+		__entry->ctrl_id = nvmet_req_to_ctrl_id(req);
 		__assign_req_name(__entry->disk, req);
 		__entry->qid = req->sq->qid;
 		__entry->cid = cmd->common.command_id;
@@ -90,7 +95,7 @@
 	),
 	TP_printk("nvmet%s: %sqid=%d, cmdid=%u, nsid=%u, flags=%#x, "
 		  "meta=%#llx, cmd=(%s, %s)",
-		__print_ctrl_name(__entry->ctrl),
+		__print_ctrl_id(__entry->ctrl_id),
 		__print_disk_name(__entry->disk),
 		__entry->qid, __entry->cid, __entry->nsid,
 		__entry->flags, __entry->metadata,
@@ -104,7 +109,7 @@
 	TP_PROTO(struct nvmet_req *req),
 	TP_ARGS(req),
 	TP_STRUCT__entry(
-		__field(struct nvmet_ctrl *, ctrl)
+		__field(u16, ctrl_id)
 		__array(char, disk, DISK_NAME_LEN)
 		__field(int, qid)
 		__field(int, cid)
@@ -112,7 +117,7 @@
 		__field(u16, status)
 	),
 	TP_fast_assign(
-		__entry->ctrl = nvmet_req_to_ctrl(req);
+		__entry->ctrl_id = nvmet_req_to_ctrl_id(req);
 		__entry->qid = req->cq->qid;
 		__entry->cid = req->cqe->command_id;
 		__entry->result = le64_to_cpu(req->cqe->result.u64);
@@ -120,7 +125,7 @@
 		__assign_req_name(__entry->disk, req);
 	),
 	TP_printk("nvmet%s: %sqid=%d, cmdid=%u, res=%#llx, status=%#x",
-		__print_ctrl_name(__entry->ctrl),
+		__print_ctrl_id(__entry->ctrl_id),
 		__print_disk_name(__entry->disk),
 		__entry->qid, __entry->cid, __entry->result, __entry->status)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvme/target/zns.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvme/target/zns.c
@@ -34,8 +34,7 @@
 
 bool nvmet_bdev_zns_enable(struct nvmet_ns *ns)
 {
-	struct request_queue *q = ns->bdev->bd_disk->queue;
-	u8 zasl = nvmet_zasl(queue_max_zone_append_sectors(q));
+	u8 zasl = nvmet_zasl(bdev_max_zone_append_sectors(ns->bdev));
 	struct gendisk *bd_disk = ns->bdev->bd_disk;
 	int ret;
 
@@ -71,7 +70,7 @@
 	return true;
 }
 
-void nvmet_execute_identify_cns_cs_ctrl(struct nvmet_req *req)
+void nvmet_execute_identify_ctrl_zns(struct nvmet_req *req)
 {
 	u8 zasl = req->sq->ctrl->subsys->zasl;
 	struct nvmet_ctrl *ctrl = req->sq->ctrl;
@@ -98,9 +97,10 @@
 
 void nvmet_execute_identify_cns_cs_ns(struct nvmet_req *req)
 {
-	struct nvme_id_ns_zns *id_zns;
+	struct nvme_id_ns_zns *id_zns = NULL;
 	u64 zsze;
 	u16 status;
+	u32 mar, mor;
 
 	if (le32_to_cpu(req->cmd->identify.nsid) == NVME_NSID_ALL) {
 		req->error_loc = offsetof(struct nvme_identify, nsid);
@@ -118,22 +118,40 @@
 	if (status)
 		goto done;
 
+	if (nvmet_ns_revalidate(req->ns)) {
+		mutex_lock(&req->ns->subsys->lock);
+		nvmet_ns_changed(req->ns->subsys, req->ns->nsid);
+		mutex_unlock(&req->ns->subsys->lock);
+	}
+
 	if (!bdev_is_zoned(req->ns->bdev)) {
+		status = NVME_SC_INVALID_FIELD | NVME_SC_DNR;
 		req->error_loc = offsetof(struct nvme_identify, nsid);
-		goto done;
+		goto out;
 	}
 
-	nvmet_ns_revalidate(req->ns);
 	zsze = (bdev_zone_sectors(req->ns->bdev) << 9) >>
 					req->ns->blksize_shift;
 	id_zns->lbafe[0].zsze = cpu_to_le64(zsze);
-	id_zns->mor = cpu_to_le32(bdev_max_open_zones(req->ns->bdev));
-	id_zns->mar = cpu_to_le32(bdev_max_active_zones(req->ns->bdev));
+
+	mor = bdev_max_open_zones(req->ns->bdev);
+	if (!mor)
+		mor = U32_MAX;
+	else
+		mor--;
+	id_zns->mor = cpu_to_le32(mor);
+
+	mar = bdev_max_active_zones(req->ns->bdev);
+	if (!mar)
+		mar = U32_MAX;
+	else
+		mar--;
+	id_zns->mar = cpu_to_le32(mar);
 
 done:
 	status = nvmet_copy_to_sgl(req, 0, id_zns, sizeof(*id_zns));
-	kfree(id_zns);
 out:
+	kfree(id_zns);
 	nvmet_req_complete(req, status);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/Kconfig
@@ -271,6 +271,17 @@
 
 	  If sure, say yes. If unsure, say no.
 
+config XLNX_SEC_CFG
+	tristate "Xilinx Secure Configuration nvmem firmware support"
+	depends on ARCH_ZYNQMP
+	help
+	  This is a driver to support secure configuration for Versal.
+	  The supported features are programming and zeroization of BBRAM AES key,
+	  programming, reading user data in BBRAM and locking user data for write.
+	  It also supports of programming AES keys in volatile user keys.
+
+	  If sure, say yes. If unsure, say no.
+
 config SPRD_EFUSE
 	tristate "Spreadtrum SoC eFuse Support"
 	depends on ARCH_SPRD || COMPILE_TEST
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/Makefile
@@ -55,6 +55,8 @@
 nvmem-sc27xx-efuse-y		:= sc27xx-efuse.o
 obj-$(CONFIG_NVMEM_ZYNQMP)	+= nvmem_zynqmp_nvmem.o
 nvmem_zynqmp_nvmem-y		:= zynqmp_nvmem.o
+obj-$(CONFIG_XLNX_SEC_CFG)	+= nvmem_xlnx_secure_config.o
+nvmem_xlnx_secure_config-y	:= xlnx_secure_config.o
 obj-$(CONFIG_SPRD_EFUSE)	+= nvmem_sprd_efuse.o
 nvmem_sprd_efuse-y		:= sprd-efuse.o
 obj-$(CONFIG_NVMEM_RMEM) 	+= nvmem-rmem.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/core.c
@@ -307,6 +307,8 @@
 	struct device *dev = kobj_to_dev(kobj);
 	struct nvmem_device *nvmem = to_nvmem_device(dev);
 
+	attr->size = nvmem->size;
+
 	return nvmem_bin_attr_get_umode(nvmem);
 }
 
@@ -360,10 +362,9 @@
 	if (!config->base_dev)
 		return -EINVAL;
 
-	if (config->type == NVMEM_TYPE_FRAM)
-		bin_attr_nvmem_eeprom_compat.attr.name = "fram";
-
 	nvmem->eeprom = bin_attr_nvmem_eeprom_compat;
+	if (config->type == NVMEM_TYPE_FRAM)
+		nvmem->eeprom.attr.name = "fram";
 	nvmem->eeprom.attr.mode = nvmem_bin_attr_get_umode(nvmem);
 	nvmem->eeprom.size = nvmem->size;
 #ifdef CONFIG_DEBUG_LOCK_ALLOC
@@ -764,31 +765,32 @@
 		return ERR_PTR(rval);
 	}
 
-	if (config->wp_gpio)
-		nvmem->wp_gpio = config->wp_gpio;
-	else
+	nvmem->id = rval;
+
+	nvmem->dev.type = &nvmem_provider_type;
+	nvmem->dev.bus = &nvmem_bus_type;
+	nvmem->dev.parent = config->dev;
+
+	device_initialize(&nvmem->dev);
+
+	if (!config->ignore_wp)
 		nvmem->wp_gpio = gpiod_get_optional(config->dev, "wp",
 						    GPIOD_OUT_HIGH);
 	if (IS_ERR(nvmem->wp_gpio)) {
-		ida_free(&nvmem_ida, nvmem->id);
 		rval = PTR_ERR(nvmem->wp_gpio);
-		kfree(nvmem);
-		return ERR_PTR(rval);
+		nvmem->wp_gpio = NULL;
+		goto err_put_device;
 	}
 
 	kref_init(&nvmem->refcnt);
 	INIT_LIST_HEAD(&nvmem->cells);
 
-	nvmem->id = rval;
 	nvmem->owner = config->owner;
 	if (!nvmem->owner && config->dev->driver)
 		nvmem->owner = config->dev->driver->owner;
 	nvmem->stride = config->stride ?: 1;
 	nvmem->word_size = config->word_size ?: 1;
 	nvmem->size = config->size;
-	nvmem->dev.type = &nvmem_provider_type;
-	nvmem->dev.bus = &nvmem_bus_type;
-	nvmem->dev.parent = config->dev;
 	nvmem->root_only = config->root_only;
 	nvmem->priv = config->priv;
 	nvmem->type = config->type;
@@ -803,18 +805,21 @@
 
 	switch (config->id) {
 	case NVMEM_DEVID_NONE:
-		dev_set_name(&nvmem->dev, "%s", config->name);
+		rval = dev_set_name(&nvmem->dev, "%s", config->name);
 		break;
 	case NVMEM_DEVID_AUTO:
-		dev_set_name(&nvmem->dev, "%s%d", config->name, nvmem->id);
+		rval = dev_set_name(&nvmem->dev, "%s%d", config->name, nvmem->id);
 		break;
 	default:
-		dev_set_name(&nvmem->dev, "%s%d",
+		rval = dev_set_name(&nvmem->dev, "%s%d",
 			     config->name ? : "nvmem",
 			     config->name ? config->id : nvmem->id);
 		break;
 	}
 
+	if (rval)
+		goto err_put_device;
+
 	nvmem->read_only = device_property_present(config->dev, "read-only") ||
 			   config->read_only || !nvmem->reg_write;
 
@@ -824,29 +829,20 @@
 
 	if (nvmem->nkeepout) {
 		rval = nvmem_validate_keepouts(nvmem);
-		if (rval) {
-			ida_free(&nvmem_ida, nvmem->id);
-			kfree(nvmem);
-			return ERR_PTR(rval);
-		}
+		if (rval)
+			goto err_put_device;
 	}
 
-	dev_dbg(&nvmem->dev, "Registering nvmem device %s\n", config->name);
-
-	rval = device_register(&nvmem->dev);
-	if (rval)
-		goto err_put_device;
-
 	if (config->compat) {
 		rval = nvmem_sysfs_setup_compat(nvmem, config);
 		if (rval)
-			goto err_device_del;
+			goto err_put_device;
 	}
 
 	if (config->cells) {
 		rval = nvmem_add_cells(nvmem, config->cells, config->ncells);
 		if (rval)
-			goto err_teardown_compat;
+			goto err_remove_cells;
 	}
 
 	rval = nvmem_add_cells_from_table(nvmem);
@@ -857,17 +853,20 @@
 	if (rval)
 		goto err_remove_cells;
 
+	dev_dbg(&nvmem->dev, "Registering nvmem device %s\n", config->name);
+
+	rval = device_add(&nvmem->dev);
+	if (rval)
+		goto err_remove_cells;
+
 	blocking_notifier_call_chain(&nvmem_notifier, NVMEM_ADD, nvmem);
 
 	return nvmem;
 
 err_remove_cells:
 	nvmem_device_remove_all_cells(nvmem);
-err_teardown_compat:
 	if (config->compat)
 		nvmem_sysfs_remove_compat(nvmem, config);
-err_device_del:
-	device_del(&nvmem->dev);
 err_put_device:
 	put_device(&nvmem->dev);
 
@@ -1113,13 +1112,13 @@
 EXPORT_SYMBOL_GPL(nvmem_device_put);
 
 /**
- * devm_nvmem_device_get() - Get nvmem cell of device form a given id
+ * devm_nvmem_device_get() - Get nvmem device of device form a given id
  *
  * @dev: Device that requests the nvmem device.
  * @id: name id for the requested nvmem device.
  *
- * Return: ERR_PTR() on error or a valid pointer to a struct nvmem_cell
- * on success.  The nvmem_cell will be freed by the automatically once the
+ * Return: ERR_PTR() on error or a valid pointer to a struct nvmem_device
+ * on success.  The nvmem_device will be freed by the automatically once the
  * device is freed.
  */
 struct nvmem_device *devm_nvmem_device_get(struct device *dev, const char *id)
@@ -1513,6 +1512,8 @@
 		return -EINVAL;
 
 	if (cell->bit_offset || cell->nbits) {
+		if (len != BITS_TO_BYTES(cell->nbits) && len != cell->bytes)
+			return -EINVAL;
 		buf = nvmem_cell_prepare_write_buffer(cell, buf, len);
 		if (IS_ERR(buf))
 			return PTR_ERR(buf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/imx-ocotp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/imx-ocotp.c
@@ -485,7 +485,7 @@
 };
 
 static const struct ocotp_params imx6sll_params = {
-	.nregs = 128,
+	.nregs = 80,
 	.bank_address_words = 0,
 	.set_timing = imx_ocotp_set_imx6_timing,
 	.ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
@@ -499,14 +499,14 @@
 };
 
 static const struct ocotp_params imx6ul_params = {
-	.nregs = 128,
+	.nregs = 144,
 	.bank_address_words = 0,
 	.set_timing = imx_ocotp_set_imx6_timing,
 	.ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 };
 
 static const struct ocotp_params imx6ull_params = {
-	.nregs = 64,
+	.nregs = 80,
 	.bank_address_words = 0,
 	.set_timing = imx_ocotp_set_imx6_timing,
 	.ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/meson-efuse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/meson-efuse.c
@@ -18,18 +18,24 @@
 			    void *val, size_t bytes)
 {
 	struct meson_sm_firmware *fw = context;
+	int ret;
 
-	return meson_sm_call_read(fw, (u8 *)val, bytes, SM_EFUSE_READ, offset,
-				  bytes, 0, 0, 0);
+	ret = meson_sm_call_read(fw, (u8 *)val, bytes, SM_EFUSE_READ, offset,
+				 bytes, 0, 0, 0);
+
+	return ret < 0 ? ret : 0;
 }
 
 static int meson_efuse_write(void *context, unsigned int offset,
 			     void *val, size_t bytes)
 {
 	struct meson_sm_firmware *fw = context;
+	int ret;
+
+	ret = meson_sm_call_write(fw, (u8 *)val, bytes, SM_EFUSE_WRITE, offset,
+				  bytes, 0, 0, 0);
 
-	return meson_sm_call_write(fw, (u8 *)val, bytes, SM_EFUSE_WRITE, offset,
-				   bytes, 0, 0, 0);
+	return ret < 0 ? ret : 0;
 }
 
 static const struct of_device_id meson_efuse_match[] = {
@@ -47,7 +53,6 @@
 	struct nvmem_config *econfig;
 	struct clk *clk;
 	unsigned int size;
-	int ret;
 
 	sm_np = of_parse_phandle(pdev->dev.of_node, "secure-monitor", 0);
 	if (!sm_np) {
@@ -60,27 +65,9 @@
 	if (!fw)
 		return -EPROBE_DEFER;
 
-	clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(clk)) {
-		ret = PTR_ERR(clk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get efuse gate");
-		return ret;
-	}
-
-	ret = clk_prepare_enable(clk);
-	if (ret) {
-		dev_err(dev, "failed to enable gate");
-		return ret;
-	}
-
-	ret = devm_add_action_or_reset(dev,
-				       (void(*)(void *))clk_disable_unprepare,
-				       clk);
-	if (ret) {
-		dev_err(dev, "failed to add disable callback");
-		return ret;
-	}
+	clk = devm_clk_get_enabled(dev, NULL);
+	if (IS_ERR(clk))
+		return dev_err_probe(dev, PTR_ERR(clk), "failed to get efuse gate");
 
 	if (meson_sm_call(fw, SM_EFUSE_USER_MAX, &size, 0, 0, 0, 0, 0) < 0) {
 		dev_err(dev, "failed to get max user");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/qcom-spmi-sdam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/qcom-spmi-sdam.c
@@ -143,6 +143,7 @@
 	sdam->sdam_config.id = NVMEM_DEVID_AUTO;
 	sdam->sdam_config.owner = THIS_MODULE;
 	sdam->sdam_config.stride = 1;
+	sdam->sdam_config.size = sdam->size;
 	sdam->sdam_config.word_size = 1;
 	sdam->sdam_config.reg_read = sdam_read;
 	sdam->sdam_config.reg_write = sdam_write;
@@ -166,6 +167,7 @@
 	{ .compatible = "qcom,spmi-sdam" },
 	{},
 };
+MODULE_DEVICE_TABLE(of, sdam_match_table);
 
 static struct platform_driver sdam_driver = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/rmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/rmem.c
@@ -37,16 +37,19 @@
 	 * but as of Dec 2020 this isn't possible on arm64.
 	 */
 	addr = memremap(priv->mem->base, available, MEMREMAP_WB);
-	if (IS_ERR(addr)) {
+	if (!addr) {
 		dev_err(priv->dev, "Failed to remap memory region\n");
-		return PTR_ERR(addr);
+		return -ENOMEM;
 	}
 
 	count = memory_read_from_buffer(val, bytes, &off, addr, available);
 
 	memunmap(addr);
 
-	return count;
+	if (count < 0)
+		return count;
+
+	return count == bytes ? 0 : -EIO;
 }
 
 static int rmem_probe(struct platform_device *pdev)
@@ -71,6 +74,7 @@
 	config.dev = dev;
 	config.priv = priv;
 	config.name = "rmem";
+	config.id = NVMEM_DEVID_AUTO;
 	config.size = mem->size;
 	config.reg_read = rmem_read;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/xlnx_secure_config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/xlnx_secure_config.c
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+
+#define AES_KEY_STRING_256_BYTES	64
+#define AES_KEY_STRING_128_BYTES	32
+#define AES_KEY_SIZE_256_BYTES		32
+#define AES_KEY_SIZE_128_BYTES		16
+
+#define BBRAM_ZEROIZE_OFFSET		0x4
+#define BBRAM_KEY_OFFSET		0x10
+#define BBRAM_USER_DATA_OFFSET		0x30
+#define BBRAM_LOCK_DATA_OFFSET		0x48
+#define AES_USER_KEY_0_OFFSET		0x110
+#define AES_USER_KEY_1_OFFSET		0x130
+#define AES_USER_KEY_2_OFFSET		0x150
+#define AES_USER_KEY_3_OFFSET		0x170
+#define AES_USER_KEY_4_OFFSET		0x190
+#define AES_USER_KEY_5_OFFSET		0x1B0
+#define AES_USER_KEY_6_OFFSET		0x1D0
+#define AES_USER_KEY_7_OFFSET		0x1F0
+
+#define BBRAM_USER_DATA_SIZE		0x4
+#define BBRAM_LOCK_DATA_SIZE		0x4
+#define BBRAM_ZEROIZE_SIZE		0x4
+
+#define BBRAM_LOCK_DATA_VALUE		0x12345678
+#define BBRAM_ZEROIZE_VALUE		0x87654321
+
+#define NVMEM_SIZE			0x230
+
+enum aes_keysrc {
+	AES_USER_KEY_0 = 12,
+	AES_USER_KEY_1 = 13,
+	AES_USER_KEY_2 = 14,
+	AES_USER_KEY_3 = 15,
+	AES_USER_KEY_4 = 16,
+	AES_USER_KEY_5 = 17,
+	AES_USER_KEY_6 = 18,
+	AES_USER_KEY_7 = 19
+};
+
+enum aes_keysize {
+	AES_KEY_SIZE_128 = 0,
+	AES_KEY_SIZE_256 = 2
+};
+
+static u_int32_t convert_char_to_nibble(char in_char, unsigned char *num)
+{
+	if ((in_char >= '0') && (in_char <= '9'))
+		*num = in_char - '0';
+	else if ((in_char >= 'a') && (in_char <= 'f'))
+		*num = in_char - 'a' + 10;
+	else if ((in_char >= 'A') && (in_char <= 'F'))
+		*num = in_char - 'A' + 10;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static u_int32_t convert_string_to_hex_be(const char *str, unsigned char *buf, u_int32_t len)
+{
+	u32 converted_len;
+	unsigned char lower_nibble = 0;
+	unsigned char upper_nibble = 0;
+	u32 str_length = strnlen(str, 64);
+
+	if (!str || !buf)
+		return -EINVAL;
+
+	if (len == 0)
+		return -EINVAL;
+
+	if ((str_length / 2) > len)
+		return -EINVAL;
+
+	converted_len = 0;
+	while (converted_len < str_length) {
+		if (convert_char_to_nibble(str[converted_len], &upper_nibble) == 0) {
+			if (convert_char_to_nibble(str[converted_len + 1], &lower_nibble) == 0)
+				buf[converted_len / 2] = (upper_nibble << 4) | lower_nibble;
+			else
+				return -EINVAL;
+		} else {
+			return -EINVAL;
+		}
+
+		converted_len += 2;
+	}
+
+	return 0;
+}
+
+static u_int32_t convert_string_to_hex_le(const char *str, unsigned char *buf, u_int32_t len)
+{
+	u32 converted_len;
+	unsigned char lower_nibble = 0;
+	unsigned char upper_nibble = 0;
+	u32 str_index;
+	u32 str_length = strnlen(str, 64);
+
+	if (!str || !buf)
+		return -EINVAL;
+
+	if (len == 0)
+		return -EINVAL;
+
+	if (str_length != len)
+		return -EINVAL;
+
+	str_index = len / 2 - 1;
+	converted_len = 0;
+
+	while (converted_len < (len)) {
+		if (convert_char_to_nibble(str[converted_len], &upper_nibble) == 0) {
+			if (convert_char_to_nibble(str[converted_len + 1], &lower_nibble) == 0) {
+				buf[str_index] = (upper_nibble << 4) | lower_nibble;
+				str_index = str_index - 1;
+			} else {
+				return -EINVAL;
+			}
+		} else {
+			return -EINVAL;
+		}
+
+		converted_len += 2;
+	}
+
+	return 0;
+}
+
+static int sec_cfg_write(void *context, unsigned int offset, void *val, size_t bytes)
+{
+	int ret;
+	struct device *dev = context;
+	dma_addr_t dma_addr;
+	u8 *data;
+
+	data = dma_alloc_coherent(dev, bytes, &dma_addr, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	switch (offset) {
+	case AES_USER_KEY_0_OFFSET:
+	case AES_USER_KEY_1_OFFSET:
+	case AES_USER_KEY_2_OFFSET:
+	case AES_USER_KEY_3_OFFSET:
+	case AES_USER_KEY_4_OFFSET:
+	case AES_USER_KEY_5_OFFSET:
+	case AES_USER_KEY_6_OFFSET:
+	case AES_USER_KEY_7_OFFSET:
+		if (bytes != AES_KEY_STRING_128_BYTES && bytes != AES_KEY_STRING_256_BYTES) {
+			ret = -EINVAL;
+		} else {
+			ret = convert_string_to_hex_be((const char *)val, data, bytes);
+			if (!ret) {
+				u32 keylen, keysrc;
+
+				keylen = (bytes == AES_KEY_STRING_128_BYTES) ? AES_KEY_SIZE_128 : AES_KEY_SIZE_256;
+				keysrc = ((offset - AES_USER_KEY_0_OFFSET) / 0x20) + 12;
+				ret = zynqmp_pm_write_aes_key(keylen, keysrc, dma_addr);
+			}
+		}
+		break;
+	case BBRAM_KEY_OFFSET:
+		if (bytes != AES_KEY_STRING_256_BYTES) {
+			ret = -EINVAL;
+		} else {
+			ret = convert_string_to_hex_le((const char *)val, data, bytes);
+			if (!ret)
+				ret = zynqmp_pm_bbram_write_aeskey(bytes / 2, dma_addr);
+		}
+		break;
+	case BBRAM_USER_DATA_OFFSET:
+		if (bytes != BBRAM_USER_DATA_SIZE)
+			ret = -EINVAL;
+		else
+			ret = zynqmp_pm_bbram_write_usrdata(*(u32 *)val);
+		break;
+	case BBRAM_LOCK_DATA_OFFSET:
+		if (bytes != BBRAM_USER_DATA_SIZE || *(u32 *)val != BBRAM_LOCK_DATA_VALUE)
+			ret = -EINVAL;
+		else
+			ret = zynqmp_pm_bbram_lock_userdata();
+		break;
+	case BBRAM_ZEROIZE_OFFSET:
+		if (bytes != BBRAM_ZEROIZE_SIZE || *(u32 *)val != BBRAM_ZEROIZE_VALUE)
+			ret = -EINVAL;
+		else
+			ret = zynqmp_pm_bbram_zeroize();
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	dma_free_coherent(dev, bytes, data, dma_addr);
+
+	return ret;
+}
+
+static int sec_cfg_read(void *context, unsigned int offset, void *val, size_t bytes)
+{
+	struct device *dev = context;
+	dma_addr_t dma_addr;
+	int *data;
+	int ret = -EINVAL;
+
+	if (offset != BBRAM_USER_DATA_OFFSET && bytes != BBRAM_USER_DATA_SIZE)
+		return -EOPNOTSUPP;
+
+	data = dma_alloc_coherent(dev, bytes, &dma_addr, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	ret = zynqmp_pm_bbram_read_usrdata(dma_addr);
+	if (!ret)
+		memcpy(val, data, bytes);
+
+	dma_free_coherent(dev, bytes, data, dma_addr);
+
+	return ret;
+}
+
+static struct nvmem_config secureconfig = {
+	.name = "xilinx-secure-config",
+	.owner = THIS_MODULE,
+	.word_size = 1,
+	.size = NVMEM_SIZE,
+};
+
+static const struct of_device_id sec_cfg_match[] = {
+	{ .compatible = "xlnx,versal-sec-cfg", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, sec_cfg_match);
+
+static int sec_cfg_probe(struct platform_device *pdev)
+{
+	struct nvmem_device *nvmem;
+
+	secureconfig.dev = &pdev->dev;
+	secureconfig.priv = &pdev->dev;
+	secureconfig.reg_read = sec_cfg_read;
+	secureconfig.reg_write = sec_cfg_write;
+
+	nvmem = nvmem_register(&secureconfig);
+	if (IS_ERR(nvmem))
+		return PTR_ERR(nvmem);
+
+	dev_dbg(&pdev->dev, "Successfully registered driver to nvmem framework");
+
+	return 0;
+}
+
+static struct platform_driver secure_config_driver = {
+	.probe = sec_cfg_probe,
+	.driver = {
+		.name = "xilinx-secure-config",
+		.of_match_table = sec_cfg_match,
+	},
+};
+
+module_platform_driver(secure_config_driver);
+
+MODULE_AUTHOR("Harsha <harsha.harsha@xilinx.com>");
+MODULE_DESCRIPTION("Versal Secure Configuration driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/nvmem/zynqmp_nvmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/nvmem/zynqmp_nvmem.c
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2019 Xilinx, Inc.
+ * Copyright (C) 2017 - 2021 Xilinx, Inc.
  */
 
+#include <linux/dma-mapping.h>
 #include <linux/module.h>
 #include <linux/nvmem-provider.h>
 #include <linux/of.h>
@@ -10,35 +11,186 @@
 #include <linux/firmware/xlnx-zynqmp.h>
 
 #define SILICON_REVISION_MASK 0xF
-
-struct zynqmp_nvmem_data {
-	struct device *dev;
-	struct nvmem_device *nvmem;
+#define P_USER_0_64_UPPER_MASK	0x5FFF0000
+#define P_USER_127_LOWER_4_BIT_MASK 0xF
+#define WORD_INBYTES		(4)
+#define SOC_VER_SIZE		(0x4)
+#define EFUSE_MEMORY_SIZE	(0x177)
+#define UNUSED_SPACE		(0x8)
+#define ZYNQMP_NVMEM_SIZE	(SOC_VER_SIZE + UNUSED_SPACE + \
+				 EFUSE_MEMORY_SIZE)
+#define SOC_VERSION_OFFSET	(0x0)
+#define EFUSE_START_OFFSET	(0xC)
+#define EFUSE_END_OFFSET	(0xFC)
+#define EFUSE_PUF_START_OFFSET	(0x100)
+#define EFUSE_PUF_MID_OFFSET	(0x140)
+#define EFUSE_PUF_END_OFFSET	(0x17F)
+#define EFUSE_NOT_ENABLED	(29)
+#define EFUSE_READ		(0)
+#define EFUSE_WRITE		(1)
+
+/**
+ * struct xilinx_efuse - the basic structure
+ * @src:	address of the buffer to store the data to be write/read
+ * @size:	no of words to be read/write
+ * @offset:	offset to be read/write`
+ * @flag:	0 - represents efuse read and 1- represents efuse write
+ * @pufuserfuse:0 - represents non-puf efuses, offset is used for read/write
+ *		1 - represents puf user fuse row number.
+ *
+ * this structure stores all the required details to
+ * read/write efuse memory.
+ */
+struct xilinx_efuse {
+	u64 src;
+	u32 size;
+	u32 offset;
+	u32 flag;
+	u32 pufuserfuse;
 };
 
-static int zynqmp_nvmem_read(void *context, unsigned int offset,
-			     void *val, size_t bytes)
+static int zynqmp_efuse_access(void *context, unsigned int offset,
+			       void *val, size_t bytes, unsigned int flag,
+			       unsigned int pufflag)
+{
+	size_t words = bytes / WORD_INBYTES;
+	struct device *dev = context;
+	dma_addr_t dma_addr, dma_buf;
+	struct xilinx_efuse *efuse;
+	char *data;
+	int ret, value;
+
+	if (bytes % WORD_INBYTES != 0) {
+		dev_err(dev, "Bytes requested should be word aligned\n");
+		return -EOPNOTSUPP;
+	}
+
+	if (pufflag == 0 && offset % WORD_INBYTES) {
+		dev_err(dev, "Offset requested should be word aligned\n");
+		return -EOPNOTSUPP;
+	}
+
+	if (pufflag == 1 && flag == EFUSE_WRITE) {
+		memcpy(&value, val, bytes);
+		if ((offset == EFUSE_PUF_START_OFFSET ||
+		     offset == EFUSE_PUF_MID_OFFSET) &&
+		    value & P_USER_0_64_UPPER_MASK) {
+			dev_err(dev, "Only lower 4 bytes are allowed to be programmed in P_USER_0 & P_USER_64\n");
+			return -EOPNOTSUPP;
+		}
+
+		if (offset == EFUSE_PUF_END_OFFSET &&
+		    (value & P_USER_127_LOWER_4_BIT_MASK)) {
+			dev_err(dev, "Only MSB 28 bits are allowed to be programmed for P_USER_127\n");
+			return -EOPNOTSUPP;
+		}
+	}
+
+	efuse = dma_alloc_coherent(dev, sizeof(struct xilinx_efuse),
+				   &dma_addr, GFP_KERNEL);
+	if (!efuse)
+		return -ENOMEM;
+
+	data = dma_alloc_coherent(dev, sizeof(bytes),
+				  &dma_buf, GFP_KERNEL);
+	if (!data) {
+		dma_free_coherent(dev, sizeof(struct xilinx_efuse),
+				  efuse, dma_addr);
+		return -ENOMEM;
+	}
+
+	if (flag == EFUSE_WRITE) {
+		memcpy(data, val, bytes);
+		efuse->flag = EFUSE_WRITE;
+	} else {
+		efuse->flag = EFUSE_READ;
+	}
+
+	efuse->src = dma_buf;
+	efuse->size = words;
+	efuse->offset = offset;
+	efuse->pufuserfuse = pufflag;
+
+	zynqmp_pm_efuse_access(dma_addr, (u32 *)&ret);
+	if (ret != 0) {
+		if (ret == EFUSE_NOT_ENABLED) {
+			dev_err(dev, "efuse access is not enabled\n");
+			ret = -EOPNOTSUPP;
+			goto END;
+		}
+		dev_err(dev, "Error in efuse read %x\n", ret);
+		ret = -EPERM;
+		goto END;
+	}
+
+	if (flag == EFUSE_READ)
+		memcpy(val, data, bytes);
+END:
+
+	dma_free_coherent(dev, sizeof(struct xilinx_efuse),
+			  efuse, dma_addr);
+	dma_free_coherent(dev, sizeof(bytes),
+			  data, dma_buf);
+
+	return ret;
+}
+
+static int zynqmp_nvmem_read(void *context, unsigned int offset, void *val, size_t bytes)
 {
-	int ret;
+	int ret, pufflag = 0;
 	int idcode, version;
-	struct zynqmp_nvmem_data *priv = context;
 
-	ret = zynqmp_pm_get_chipid(&idcode, &version);
-	if (ret < 0)
-		return ret;
+	if (offset >= EFUSE_PUF_START_OFFSET && offset <= EFUSE_PUF_END_OFFSET)
+		pufflag = 1;
 
-	dev_dbg(priv->dev, "Read chipid val %x %x\n", idcode, version);
-	*(int *)val = version & SILICON_REVISION_MASK;
+	switch (offset) {
+	/* Soc version offset is zero */
+	case SOC_VERSION_OFFSET:
+		if (bytes != SOC_VER_SIZE)
+			return -EOPNOTSUPP;
+
+		ret = zynqmp_pm_get_chipid((u32 *)&idcode, (u32 *)&version);
+		if (ret < 0)
+			return ret;
+
+		pr_debug("Read chipid val %x %x\n", idcode, version);
+		*(int *)val = version & SILICON_REVISION_MASK;
+		break;
+	/* Efuse offset starts from 0xc */
+	case EFUSE_START_OFFSET ... EFUSE_END_OFFSET:
+	case EFUSE_PUF_START_OFFSET ... EFUSE_PUF_END_OFFSET:
+		ret = zynqmp_efuse_access(context, offset, val,
+					  bytes, EFUSE_READ, pufflag);
+		break;
+	default:
+		*(u32 *)val = 0xDEADBEEF;
+		ret = 0;
+		break;
+	}
 
-	return 0;
+	return ret;
+}
+
+static int zynqmp_nvmem_write(void *context,
+			      unsigned int offset, void *val, size_t bytes)
+{
+	int pufflag = 0;
+
+	if (offset < EFUSE_START_OFFSET || offset > EFUSE_PUF_END_OFFSET)
+		return -EOPNOTSUPP;
+
+	if (offset >= EFUSE_PUF_START_OFFSET && offset <= EFUSE_PUF_END_OFFSET)
+		pufflag = 1;
+
+	return zynqmp_efuse_access(context, offset,
+				   val, bytes, EFUSE_WRITE, pufflag);
 }
 
 static struct nvmem_config econfig = {
 	.name = "zynqmp-nvmem",
 	.owner = THIS_MODULE,
 	.word_size = 1,
-	.size = 1,
-	.read_only = true,
+	.size = ZYNQMP_NVMEM_SIZE,
 };
 
 static const struct of_device_id zynqmp_nvmem_match[] = {
@@ -49,21 +201,20 @@
 
 static int zynqmp_nvmem_probe(struct platform_device *pdev)
 {
-	struct device *dev = &pdev->dev;
-	struct zynqmp_nvmem_data *priv;
-
-	priv = devm_kzalloc(dev, sizeof(struct zynqmp_nvmem_data), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
+	struct nvmem_device *nvmem;
 
-	priv->dev = dev;
-	econfig.dev = dev;
+	econfig.dev = &pdev->dev;
+	econfig.priv = &pdev->dev;
 	econfig.reg_read = zynqmp_nvmem_read;
-	econfig.priv = priv;
+	econfig.reg_write = zynqmp_nvmem_write;
 
-	priv->nvmem = devm_nvmem_register(dev, &econfig);
+	nvmem = nvmem_register(&econfig);
+	if (IS_ERR(nvmem))
+		return PTR_ERR(nvmem);
 
-	return PTR_ERR_OR_ZERO(priv->nvmem);
+	platform_set_drvdata(pdev, nvmem);
+
+	return 0;
 }
 
 static struct platform_driver zynqmp_nvmem_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/Kconfig
@@ -70,10 +70,6 @@
 	def_bool y
 	depends on !SPARC && IRQ_DOMAIN
 
-config OF_NET
-	depends on NETDEVICES
-	def_bool y
-
 config OF_RESERVED_MEM
 	def_bool OF_EARLY_FLATTREE
 
@@ -98,4 +94,15 @@
 	# arches should select this if DMA is coherent by default for OF devices
 	bool
 
+config OF_CONFIGFS
+	bool "Device Tree Overlay ConfigFS interface"
+	select CONFIGFS_FS
+	depends on OF_OVERLAY
+	help
+	  Select this option to enable simple user-space driven DT overlay
+	  interface to support device tree manipulated at runtime.
+	  Say Y here to include this support.
+
+	  If unsure, say N.
+
 endif # OF
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/Makefile
@@ -1,13 +1,13 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-y = base.o device.o platform.o property.o
 obj-$(CONFIG_OF_KOBJ) += kobj.o
+obj-$(CONFIG_OF_CONFIGFS) += configfs.o
 obj-$(CONFIG_OF_DYNAMIC) += dynamic.o
 obj-$(CONFIG_OF_FLATTREE) += fdt.o
 obj-$(CONFIG_OF_EARLY_FLATTREE) += fdt_address.o
 obj-$(CONFIG_OF_PROMTREE) += pdt.o
 obj-$(CONFIG_OF_ADDRESS)  += address.o
 obj-$(CONFIG_OF_IRQ)    += irq.o
-obj-$(CONFIG_OF_NET)	+= of_net.o
 obj-$(CONFIG_OF_UNITTEST) += unittest.o
 obj-$(CONFIG_OF_RESERVED_MEM) += of_reserved_mem.o
 obj-$(CONFIG_OF_RESOLVE)  += resolver.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/address.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/address.c
@@ -50,7 +50,7 @@
 	u64		(*map)(__be32 *addr, const __be32 *range,
 				int na, int ns, int pna);
 	int		(*translate)(__be32 *addr, u64 offset, int na);
-	bool	has_flags;
+	int		flag_cells;
 	unsigned int	(*get_flags)(const __be32 *addr);
 };
 
@@ -95,11 +95,43 @@
 	return 0;
 }
 
+static unsigned int of_bus_default_flags_get_flags(const __be32 *addr)
+{
+	return of_read_number(addr, 1);
+}
+
 static unsigned int of_bus_default_get_flags(const __be32 *addr)
 {
 	return IORESOURCE_MEM;
 }
 
+static u64 of_bus_default_flags_map(__be32 *addr, const __be32 *range, int na,
+				    int ns, int pna)
+{
+	u64 cp, s, da;
+
+	/* Check that flags match */
+	if (*addr != *range)
+		return OF_BAD_ADDR;
+
+	/* Read address values, skipping high cell */
+	cp = of_read_number(range + 1, na - 1);
+	s  = of_read_number(range + na + pna, ns);
+	da = of_read_number(addr + 1, na - 1);
+
+	pr_debug("default flags map, cp=%llx, s=%llx, da=%llx\n", cp, s, da);
+
+	if (da < cp || da >= (cp + s))
+		return OF_BAD_ADDR;
+	return da - cp;
+}
+
+static int of_bus_default_flags_translate(__be32 *addr, u64 offset, int na)
+{
+	/* Keep "flags" part (high cell) in translated address */
+	return of_bus_default_translate(addr + 1, offset, na - 1);
+}
+
 #ifdef CONFIG_PCI
 static unsigned int of_bus_pci_get_flags(const __be32 *addr)
 {
@@ -189,10 +221,6 @@
 	return da - cp;
 }
 
-static int of_bus_pci_translate(__be32 *addr, u64 offset, int na)
-{
-	return of_bus_default_translate(addr + 1, offset, na - 1);
-}
 #endif /* CONFIG_PCI */
 
 int of_pci_address_to_resource(struct device_node *dev, int bar,
@@ -302,11 +330,6 @@
 	return da - cp;
 }
 
-static int of_bus_isa_translate(__be32 *addr, u64 offset, int na)
-{
-	return of_bus_default_translate(addr + 1, offset, na - 1);
-}
-
 static unsigned int of_bus_isa_get_flags(const __be32 *addr)
 {
 	unsigned int flags = 0;
@@ -319,6 +342,11 @@
 	return flags;
 }
 
+static int of_bus_default_flags_match(struct device_node *np)
+{
+	return of_bus_n_addr_cells(np) == 3;
+}
+
 /*
  * Array of bus specific translators
  */
@@ -332,8 +360,8 @@
 		.match = of_bus_pci_match,
 		.count_cells = of_bus_pci_count_cells,
 		.map = of_bus_pci_map,
-		.translate = of_bus_pci_translate,
-		.has_flags = true,
+		.translate = of_bus_default_flags_translate,
+		.flag_cells = 1,
 		.get_flags = of_bus_pci_get_flags,
 	},
 #endif /* CONFIG_PCI */
@@ -344,10 +372,21 @@
 		.match = of_bus_isa_match,
 		.count_cells = of_bus_isa_count_cells,
 		.map = of_bus_isa_map,
-		.translate = of_bus_isa_translate,
-		.has_flags = true,
+		.translate = of_bus_default_flags_translate,
+		.flag_cells = 1,
 		.get_flags = of_bus_isa_get_flags,
 	},
+	/* Default with flags cell */
+	{
+		.name = "default-flags",
+		.addresses = "reg",
+		.match = of_bus_default_flags_match,
+		.count_cells = of_bus_default_count_cells,
+		.map = of_bus_default_flags_map,
+		.translate = of_bus_default_flags_translate,
+		.flag_cells = 1,
+		.get_flags = of_bus_default_flags_get_flags,
+	},
 	/* Default */
 	{
 		.name = "default",
@@ -427,7 +466,8 @@
 	}
 	if (ranges == NULL || rlen == 0) {
 		offset = of_read_number(addr, na);
-		memset(addr, 0, pna * 4);
+		/* set address to zero, pass flags through */
+		memset(addr + pbus->flag_cells, 0, (pna - pbus->flag_cells) * 4);
 		pr_debug("empty ranges; 1:1 translation\n");
 		goto finish;
 	}
@@ -594,7 +634,7 @@
 	if (ret < 0)
 		return of_get_parent(np);
 
-	return of_node_get(args.np);
+	return args.np;
 }
 
 static struct device_node *of_get_next_dma_parent(struct device_node *np)
@@ -712,7 +752,7 @@
 	int na = parser->na;
 	int ns = parser->ns;
 	int np = parser->pna + na + ns;
-	int busflag_na = 0;
+	int busflag_na = parser->bus->flag_cells;
 
 	if (!range)
 		return NULL;
@@ -722,10 +762,6 @@
 
 	range->flags = parser->bus->get_flags(parser->range);
 
-	/* A extra cell for resource flags */
-	if (parser->bus->has_flags)
-		busflag_na = 1;
-
 	range->bus_addr = of_read_number(parser->range + busflag_na, na - busflag_na);
 
 	if (parser->dma)
@@ -963,8 +999,19 @@
 	}
 
 	of_dma_range_parser_init(&parser, node);
-	for_each_of_range(&parser, &range)
+	for_each_of_range(&parser, &range) {
+		if (range.cpu_addr == OF_BAD_ADDR) {
+			pr_err("translation of DMA address(%llx) to CPU address failed node(%pOF)\n",
+			       range.bus_addr, node);
+			continue;
+		}
 		num_ranges++;
+	}
+
+	if (!num_ranges) {
+		ret = -EINVAL;
+		goto out;
+	}
 
 	r = kcalloc(num_ranges + 1, sizeof(*r), GFP_KERNEL);
 	if (!r) {
@@ -973,18 +1020,16 @@
 	}
 
 	/*
-	 * Record all info in the generic DMA ranges array for struct device.
+	 * Record all info in the generic DMA ranges array for struct device,
+	 * returning an error if we don't find any parsable ranges.
 	 */
 	*map = r;
 	of_dma_range_parser_init(&parser, node);
 	for_each_of_range(&parser, &range) {
 		pr_debug("dma_addr(%llx) cpu_addr(%llx) size(%llx)\n",
 			 range.bus_addr, range.cpu_addr, range.size);
-		if (range.cpu_addr == OF_BAD_ADDR) {
-			pr_err("translation of DMA address(%llx) to CPU address failed node(%pOF)\n",
-			       range.bus_addr, node);
+		if (range.cpu_addr == OF_BAD_ADDR)
 			continue;
-		}
 		r->cpu_start = range.cpu_addr;
 		r->dma_start = range.bus_addr;
 		r->size = range.size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/base.c
@@ -925,10 +925,10 @@
 	/* The path could begin with an alias */
 	if (*path != '/') {
 		int len;
-		const char *p = separator;
+		const char *p = strchrnul(path, '/');
 
-		if (!p)
-			p = strchrnul(path, '/');
+		if (separator && separator < p)
+			p = separator;
 		len = p - path;
 
 		/* of_aliases must not be NULL */
@@ -1327,9 +1327,14 @@
 		 * property data length
 		 */
 		if (it->cur + count > it->list_end) {
-			pr_err("%pOF: %s = %d found %d\n",
-			       it->parent, it->cells_name,
-			       count, it->cell_count);
+			if (it->cells_name)
+				pr_err("%pOF: %s = %d found %td\n",
+					it->parent, it->cells_name,
+					count, it->list_end - it->cur);
+			else
+				pr_err("%pOF: phandle %s needs %d, found %td\n",
+					it->parent, of_node_full_name(it->node),
+					count, it->list_end - it->cur);
 			goto err;
 		}
 	}
@@ -1615,8 +1620,10 @@
 			map_len--;
 
 			/* Check if not found */
-			if (!new)
+			if (!new) {
+				ret = -EINVAL;
 				goto put;
+			}
 
 			if (!of_device_is_available(new))
 				match = 0;
@@ -1626,17 +1633,20 @@
 				goto put;
 
 			/* Check for malformed properties */
-			if (WARN_ON(new_size > MAX_PHANDLE_ARGS))
-				goto put;
-			if (map_len < new_size)
+			if (WARN_ON(new_size > MAX_PHANDLE_ARGS) ||
+			    map_len < new_size) {
+				ret = -EINVAL;
 				goto put;
+			}
 
 			/* Move forward by new node's #<list>-cells amount */
 			map += new_size;
 			map_len -= new_size;
 		}
-		if (!match)
+		if (!match) {
+			ret = -ENOENT;
 			goto put;
+		}
 
 		/* Get the <list>-map-pass-thru property (optional) */
 		pass = of_get_property(cur, pass_name, NULL);
@@ -1648,7 +1658,6 @@
 		 * specifier into the out_args structure, keeping the
 		 * bits specified in <list>-map-pass-thru.
 		 */
-		match_array = map - new_size;
 		for (i = 0; i < new_size; i++) {
 			__be32 val = *(map - new_size + i);
 
@@ -1657,6 +1666,7 @@
 				val |= cpu_to_be32(out_args->args[i]) & pass[i];
 			}
 
+			initial_match_array[i] = val;
 			out_args->args[i] = be32_to_cpu(val);
 		}
 		out_args->args_count = list_size = new_size;
@@ -1664,6 +1674,7 @@
 		out_args->np = new;
 		of_node_put(cur);
 		cur = new;
+		new = NULL;
 	}
 put:
 	of_node_put(cur);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/configfs.c
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Configfs entries for device-tree
+ *
+ * Copyright (C) 2013 - Pantelis Antoniou <panto@antoniou-consulting.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <linux/ctype.h>
+#include <linux/cpu.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_fdt.h>
+#include <linux/spinlock.h>
+#include <linux/sizes.h>
+#include <linux/slab.h>
+#include <linux/proc_fs.h>
+#include <linux/configfs.h>
+#include <linux/types.h>
+#include <linux/stat.h>
+#include <linux/limits.h>
+#include <linux/file.h>
+#include <linux/vmalloc.h>
+#include <linux/firmware.h>
+
+#include "of_private.h"
+
+struct cfs_overlay_item {
+	struct config_item	item;
+
+	char			path[PATH_MAX];
+
+	const struct firmware	*fw;
+	struct device_node	*overlay;
+	int			ov_id;
+
+	void			*dtbo;
+	int			dtbo_size;
+
+	void			*mem;
+};
+
+static DEFINE_MUTEX(overlay_lock);
+
+static int create_overlay(struct cfs_overlay_item *overlay, void *blob)
+{
+	int err;
+
+	/* FIXME */
+	err = of_overlay_fdt_apply(blob, overlay->dtbo_size, &overlay->ov_id);
+	if (err < 0) {
+		pr_err("%s: Failed to create overlay (err=%d)\n",
+		       __func__, err);
+		return err;
+	}
+
+	return err;
+}
+
+static inline struct cfs_overlay_item
+		*to_cfs_overlay_item(struct config_item *item)
+{
+	return item ? container_of(item, struct cfs_overlay_item, item) : NULL;
+}
+
+static ssize_t cfs_overlay_item_path_show(struct config_item *item, char *page)
+{
+	return sprintf(page, "%s\n", to_cfs_overlay_item(item)->path);
+}
+
+static ssize_t cfs_overlay_item_path_store(struct config_item *item,
+					   const char *page, size_t count)
+{
+	struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
+	const char *p = page;
+	char *s;
+	int err;
+
+	/* if it's set do not allow changes */
+	if (overlay->path[0] != '\0' || overlay->dtbo_size > 0)
+		return -EPERM;
+
+	/* copy to path buffer (and make sure it's always zero terminated */
+	count = snprintf(overlay->path, sizeof(overlay->path) - 1, "%s", p);
+	overlay->path[sizeof(overlay->path) - 1] = '\0';
+
+	/* strip trailing newlines */
+	s = overlay->path + strlen(overlay->path);
+	while (s > overlay->path && *--s == '\n')
+		*s = '\0';
+
+	pr_debug("%s: path is '%s'\n", __func__, overlay->path);
+
+	err = request_firmware(&overlay->fw, overlay->path, NULL);
+	if (err != 0)
+		goto out_err;
+
+	overlay->dtbo_size = overlay->fw->size;
+	err = create_overlay(overlay, (void *)overlay->fw->data);
+	if (err < 0)
+		goto out_err;
+
+	return count;
+
+out_err:
+
+	release_firmware(overlay->fw);
+	overlay->fw = NULL;
+
+	overlay->path[0] = '\0';
+
+	return count;
+}
+
+static ssize_t cfs_overlay_item_status_show(struct config_item *item,
+					    char *page)
+{
+	return sprintf(page, "%s\n", to_cfs_overlay_item(item)->ov_id >= 0 ?
+					"applied" : "unapplied");
+}
+
+CONFIGFS_ATTR(cfs_overlay_item_, path);
+CONFIGFS_ATTR_RO(cfs_overlay_item_, status);
+
+static struct configfs_attribute *cfs_overlay_attrs[] = {
+	&cfs_overlay_item_attr_path,
+	&cfs_overlay_item_attr_status,
+	NULL,
+};
+
+ssize_t cfs_overlay_item_dtbo_read(struct config_item *item,
+				   void *buf, size_t max_count)
+{
+	struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
+
+	pr_debug("%s: buf=%p max_count=%zu\n", __func__, buf, max_count);
+
+	if (!overlay->dtbo)
+		return 0;
+
+	/* copy if buffer provided */
+	if (buf) {
+		/* the buffer must be large enough */
+		if (overlay->dtbo_size > max_count)
+			return -ENOSPC;
+
+		memcpy(buf, overlay->dtbo, overlay->dtbo_size);
+	}
+
+	return overlay->dtbo_size;
+}
+
+ssize_t cfs_overlay_item_dtbo_write(struct config_item *item,
+				    const void *buf, size_t count)
+{
+	struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
+	int err;
+
+	/* if it's set do not allow changes */
+	if (overlay->path[0] != '\0' || overlay->dtbo_size > 0)
+		return -EPERM;
+
+	/* copy the contents */
+	overlay->dtbo = kmemdup(buf, count, GFP_KERNEL);
+	if (!overlay->dtbo)
+		return -ENOMEM;
+
+	overlay->dtbo_size = count;
+
+	err = create_overlay(overlay, overlay->dtbo);
+	if (err < 0)
+		goto out_err;
+
+	return count;
+
+out_err:
+	kfree(overlay->dtbo);
+	overlay->dtbo = NULL;
+	overlay->dtbo_size = 0;
+
+	return err;
+}
+
+CONFIGFS_BIN_ATTR(cfs_overlay_item_, dtbo, NULL, SZ_1M);
+
+static struct configfs_bin_attribute *cfs_overlay_bin_attrs[] = {
+	&cfs_overlay_item_attr_dtbo,
+	NULL,
+};
+
+static void cfs_overlay_release(struct config_item *item)
+{
+	struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
+
+	if (overlay->ov_id >= 0)
+		of_overlay_remove(&overlay->ov_id);
+	if (overlay->fw)
+		release_firmware(overlay->fw);
+	/* kfree with NULL is safe */
+	kfree(overlay->dtbo);
+	kfree(overlay->mem);
+	kfree(overlay);
+}
+
+static struct configfs_item_operations cfs_overlay_item_ops = {
+	.release		= cfs_overlay_release,
+};
+
+static struct config_item_type cfs_overlay_type = {
+	.ct_item_ops	= &cfs_overlay_item_ops,
+	.ct_attrs	= cfs_overlay_attrs,
+	.ct_bin_attrs	= cfs_overlay_bin_attrs,
+	.ct_owner	= THIS_MODULE,
+};
+
+static struct config_item
+	*cfs_overlay_group_make_item(struct config_group *group,
+				     const char *name)
+{
+	struct cfs_overlay_item *overlay;
+
+	overlay = kzalloc(sizeof(*overlay), GFP_KERNEL);
+	if (!overlay)
+		return ERR_PTR(-ENOMEM);
+	overlay->ov_id = -1;
+	config_item_init_type_name(&overlay->item, name, &cfs_overlay_type);
+
+	return &overlay->item;
+}
+
+static void cfs_overlay_group_drop_item(struct config_group *group,
+					struct config_item *item)
+{
+	struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
+
+	config_item_put(&overlay->item);
+}
+
+static struct configfs_group_operations overlays_ops = {
+	.make_item	= cfs_overlay_group_make_item,
+	.drop_item	= cfs_overlay_group_drop_item,
+};
+
+static struct config_item_type overlays_type = {
+	.ct_group_ops   = &overlays_ops,
+	.ct_owner       = THIS_MODULE,
+};
+
+static struct configfs_group_operations of_cfs_ops = {
+	/* empty - we don't allow anything to be created */
+};
+
+static struct config_item_type of_cfs_type = {
+	.ct_group_ops   = &of_cfs_ops,
+	.ct_owner       = THIS_MODULE,
+};
+
+struct config_group of_cfs_overlay_group;
+
+static struct configfs_subsystem of_cfs_subsys = {
+	.su_group = {
+		.cg_item = {
+			.ci_namebuf = "device-tree",
+			.ci_type = &of_cfs_type,
+		},
+	},
+	.su_mutex = __MUTEX_INITIALIZER(of_cfs_subsys.su_mutex),
+};
+
+static int __init of_cfs_init(void)
+{
+	int ret;
+
+	pr_info("%s\n", __func__);
+
+	config_group_init(&of_cfs_subsys.su_group);
+	config_group_init_type_name(&of_cfs_overlay_group, "overlays",
+				    &overlays_type);
+	configfs_add_default_group(&of_cfs_overlay_group,
+				   &of_cfs_subsys.su_group);
+
+	ret = configfs_register_subsystem(&of_cfs_subsys);
+	if (ret != 0) {
+		pr_err("%s: failed to register subsys\n", __func__);
+		goto out;
+	}
+	pr_info("%s: OK\n", __func__);
+out:
+	return ret;
+}
+late_initcall(of_cfs_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/device.c
@@ -81,8 +81,11 @@
 		 * restricted-dma-pool region is allowed.
 		 */
 		if (of_device_is_compatible(node, "restricted-dma-pool") &&
-		    of_device_is_available(node))
+		    of_device_is_available(node)) {
+			of_node_put(node);
 			break;
+		}
+		of_node_put(node);
 	}
 
 	/*
@@ -287,12 +290,15 @@
 	if (size < 0)
 		return size;
 
-	str = kmalloc(size + 1, GFP_KERNEL);
+	/* Reserve an additional byte for the trailing '\0' */
+	size++;
+
+	str = kmalloc(size, GFP_KERNEL);
 	if (!str)
 		return -ENOMEM;
 
 	of_device_get_modalias(dev, str, size);
-	str[size] = '\0';
+	str[size - 1] = '\0';
 	ret = request_module(str);
 	kfree(str);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/dynamic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/dynamic.c
@@ -9,6 +9,7 @@
 
 #define pr_fmt(fmt)	"OF: " fmt
 
+#include <linux/device.h>
 #include <linux/of.h>
 #include <linux/spinlock.h>
 #include <linux/slab.h>
@@ -63,15 +64,14 @@
 }
 EXPORT_SYMBOL_GPL(of_reconfig_notifier_unregister);
 
-#ifdef DEBUG
-const char *action_names[] = {
+static const char *action_names[] = {
+	[0] = "INVALID",
 	[OF_RECONFIG_ATTACH_NODE] = "ATTACH_NODE",
 	[OF_RECONFIG_DETACH_NODE] = "DETACH_NODE",
 	[OF_RECONFIG_ADD_PROPERTY] = "ADD_PROPERTY",
 	[OF_RECONFIG_REMOVE_PROPERTY] = "REMOVE_PROPERTY",
 	[OF_RECONFIG_UPDATE_PROPERTY] = "UPDATE_PROPERTY",
 };
-#endif
 
 int of_reconfig_notify(unsigned long action, struct of_reconfig_data *p)
 {
@@ -105,8 +105,9 @@
  *
  * Returns the new state of a device based on the notifier used.
  *
- * Return: 0 on device going from enabled to disabled, 1 on device
- * going from disabled to enabled and -1 on no change.
+ * Return: OF_RECONFIG_CHANGE_REMOVE on device going from enabled to
+ * disabled, OF_RECONFIG_CHANGE_ADD on device going from disabled to
+ * enabled and OF_RECONFIG_NO_CHANGE on no change.
  */
 int of_reconfig_get_state_change(unsigned long action, struct of_reconfig_data *pr)
 {
@@ -594,21 +595,9 @@
 		}
 
 		ret = __of_add_property(ce->np, ce->prop);
-		if (ret) {
-			pr_err("changeset: add_property failed @%pOF/%s\n",
-				ce->np,
-				ce->prop->name);
-			break;
-		}
 		break;
 	case OF_RECONFIG_REMOVE_PROPERTY:
 		ret = __of_remove_property(ce->np, ce->prop);
-		if (ret) {
-			pr_err("changeset: remove_property failed @%pOF/%s\n",
-				ce->np,
-				ce->prop->name);
-			break;
-		}
 		break;
 
 	case OF_RECONFIG_UPDATE_PROPERTY:
@@ -622,20 +611,17 @@
 		}
 
 		ret = __of_update_property(ce->np, ce->prop, &old_prop);
-		if (ret) {
-			pr_err("changeset: update_property failed @%pOF/%s\n",
-				ce->np,
-				ce->prop->name);
-			break;
-		}
 		break;
 	default:
 		ret = -EINVAL;
 	}
 	raw_spin_unlock_irqrestore(&devtree_lock, flags);
 
-	if (ret)
+	if (ret) {
+		pr_err("changeset: apply failed: %-15s %pOF:%s\n",
+		       action_names[ce->action], ce->np, ce->prop->name);
 		return ret;
+	}
 
 	switch (ce->action) {
 	case OF_RECONFIG_ATTACH_NODE:
@@ -693,6 +679,17 @@
 {
 	struct of_changeset_entry *ce, *cen;
 
+	/*
+	 * When a device is deleted, the device links to/from it are also queued
+	 * for deletion. Until these device links are freed, the devices
+	 * themselves aren't freed. If the device being deleted is due to an
+	 * overlay change, this device might be holding a reference to a device
+	 * node that will be freed. So, wait until all already pending device
+	 * links are deleted before freeing a device node. This ensures we don't
+	 * free any device node that has a non-zero reference count.
+	 */
+	device_link_wait_removal();
+
 	list_for_each_entry_safe_reverse(ce, cen, &ocs->entries, node)
 		__of_changeset_entry_destroy(ce);
 }
@@ -917,6 +914,9 @@
 {
 	struct of_changeset_entry *ce;
 
+	if (WARN_ON(action >= ARRAY_SIZE(action_names)))
+		return -EINVAL;
+
 	ce = kzalloc(sizeof(*ce), GFP_KERNEL);
 	if (!ce)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/fdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/fdt.c
@@ -245,7 +245,7 @@
 	}
 
 	*pnp = np;
-	return true;
+	return 0;
 }
 
 static void reverse_nodes(struct device_node *parent)
@@ -313,7 +313,7 @@
 	for (offset = 0;
 	     offset >= 0 && depth >= initial_depth;
 	     offset = fdt_next_node(blob, offset, &depth)) {
-		if (WARN_ON_ONCE(depth >= FDT_MAX_DEPTH))
+		if (WARN_ON_ONCE(depth >= FDT_MAX_DEPTH - 1))
 			continue;
 
 		if (!IS_ENABLED(CONFIG_OF_KOBJ) &&
@@ -482,9 +482,11 @@
 	if (nomap) {
 		/*
 		 * If the memory is already reserved (by another region), we
-		 * should not allow it to be marked nomap.
+		 * should not allow it to be marked nomap, but don't worry
+		 * if the region isn't memory as it won't be mapped.
 		 */
-		if (memblock_is_region_reserved(base, size))
+		if (memblock_overlaps_region(&memblock.memory, base, size) &&
+		    memblock_is_region_reserved(base, size))
 			return -EBUSY;
 
 		return memblock_mark_nomap(base, size);
@@ -969,18 +971,22 @@
 		 elfcorehdr_addr, elfcorehdr_size);
 }
 
-static phys_addr_t cap_mem_addr;
-static phys_addr_t cap_mem_size;
+static unsigned long chosen_node_offset = -FDT_ERR_NOTFOUND;
 
 /**
  * early_init_dt_check_for_usable_mem_range - Decode usable memory range
  * location from flat tree
- * @node: reference to node containing usable memory range location ('chosen')
  */
-static void __init early_init_dt_check_for_usable_mem_range(unsigned long node)
+void __init early_init_dt_check_for_usable_mem_range(void)
 {
 	const __be32 *prop;
 	int len;
+	phys_addr_t cap_mem_addr;
+	phys_addr_t cap_mem_size;
+	unsigned long node = chosen_node_offset;
+
+	if ((long)node < 0)
+		return;
 
 	pr_debug("Looking for usable-memory-range property... ");
 
@@ -993,6 +999,8 @@
 
 	pr_debug("cap_mem_start=%pa cap_mem_size=%pa\n", &cap_mem_addr,
 		 &cap_mem_size);
+
+	memblock_cap_memory_range(cap_mem_addr, cap_mem_size);
 }
 
 #ifdef CONFIG_SERIAL_EARLYCON
@@ -1141,9 +1149,10 @@
 	    (strcmp(uname, "chosen") != 0 && strcmp(uname, "chosen@0") != 0))
 		return 0;
 
+	chosen_node_offset = node;
+
 	early_init_dt_check_for_initrd(node);
 	early_init_dt_check_for_elfcorehdr(node);
-	early_init_dt_check_for_usable_mem_range(node);
 
 	/* Retrieve command line */
 	p = of_get_flat_dt_prop(node, "bootargs", &l);
@@ -1279,7 +1288,7 @@
 	of_scan_flat_dt(early_init_dt_scan_memory, NULL);
 
 	/* Handle linux,usable-memory-range property */
-	memblock_cap_memory_range(cap_mem_addr, cap_mem_size);
+	early_init_dt_check_for_usable_mem_range();
 }
 
 bool __init early_init_dt_scan(void *params)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/irq.c
@@ -288,7 +288,8 @@
 	struct device_node *p;
 	const __be32 *addr;
 	u32 intsize;
-	int i, res;
+	int i, res, addr_len;
+	__be32 addr_buf[3] = { 0 };
 
 	pr_debug("of_irq_parse_one: dev=%pOF, index=%d\n", device, index);
 
@@ -297,13 +298,20 @@
 		return of_irq_parse_oldworld(device, index, out_irq);
 
 	/* Get the reg property (if any) */
-	addr = of_get_property(device, "reg", NULL);
+	addr_len = 0;
+	addr = of_get_property(device, "reg", &addr_len);
+
+	/* Prevent out-of-bounds read in case of longer interrupt parent address size */
+	if (addr_len > sizeof(addr_buf))
+		addr_len = sizeof(addr_buf);
+	if (addr)
+		memcpy(addr_buf, addr, addr_len);
 
 	/* Try the new-style interrupts-extended first */
 	res = of_parse_phandle_with_args(device, "interrupts-extended",
 					"#interrupt-cells", index, out_irq);
 	if (!res)
-		return of_irq_parse_raw(addr, out_irq);
+		return of_irq_parse_raw(addr_buf, out_irq);
 
 	/* Look for the interrupt parent. */
 	p = of_irq_find_parent(device);
@@ -333,7 +341,7 @@
 
 
 	/* Check if there are any interrupt-map translations to process */
-	res = of_irq_parse_raw(addr, out_irq);
+	res = of_irq_parse_raw(addr_buf, out_irq);
  out:
 	of_node_put(p);
 	return res;
@@ -635,8 +643,7 @@
  * @np: device node for @dev
  * @token: bus type for this domain
  *
- * Parse the msi-parent property (both the simple and the complex
- * versions), and returns the corresponding MSI domain.
+ * Parse the msi-parent property and returns the corresponding MSI domain.
  *
  * Returns: the MSI domain for this device (or NULL on failure).
  */
@@ -644,33 +651,14 @@
 				     struct device_node *np,
 				     enum irq_domain_bus_token token)
 {
-	struct device_node *msi_np;
+	struct of_phandle_iterator it;
 	struct irq_domain *d;
+	int err;
 
-	/* Check for a single msi-parent property */
-	msi_np = of_parse_phandle(np, "msi-parent", 0);
-	if (msi_np && !of_property_read_bool(msi_np, "#msi-cells")) {
-		d = irq_find_matching_host(msi_np, token);
-		if (!d)
-			of_node_put(msi_np);
-		return d;
-	}
-
-	if (token == DOMAIN_BUS_PLATFORM_MSI) {
-		/* Check for the complex msi-parent version */
-		struct of_phandle_args args;
-		int index = 0;
-
-		while (!of_parse_phandle_with_args(np, "msi-parent",
-						   "#msi-cells",
-						   index, &args)) {
-			d = irq_find_matching_host(args.np, token);
-			if (d)
-				return d;
-
-			of_node_put(args.np);
-			index++;
-		}
+	of_for_each_phandle(&it, err, np, "msi-parent", "#msi-cells", 0) {
+		d = irq_find_matching_host(it.node, token);
+		if (d)
+			return d;
 	}
 
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/kexec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/kexec.c
@@ -125,6 +125,7 @@
 {
 	int ret, len;
 	unsigned long tmp_addr;
+	unsigned long start_pfn, end_pfn;
 	size_t tmp_size;
 	const void *prop;
 
@@ -139,6 +140,22 @@
 	if (ret)
 		return ret;
 
+	/* Do some sanity on the returned size for the ima-kexec buffer */
+	if (!tmp_size)
+		return -ENOENT;
+
+	/*
+	 * Calculate the PFNs for the buffer and ensure
+	 * they are with in addressable memory.
+	 */
+	start_pfn = PHYS_PFN(tmp_addr);
+	end_pfn = PHYS_PFN(tmp_addr + tmp_size - 1);
+	if (!page_is_ram(start_pfn) || !page_is_ram(end_pfn)) {
+		pr_warn("IMA buffer at 0x%lx, size = 0x%zx beyond memory\n",
+			tmp_addr, tmp_size);
+		return -EINVAL;
+	}
+
 	*addr = __va(tmp_addr);
 	*size = tmp_size;
 
@@ -148,7 +165,7 @@
 /**
  * ima_free_kexec_buffer - free memory used by the IMA buffer
  */
-int ima_free_kexec_buffer(void)
+int __init ima_free_kexec_buffer(void)
 {
 	int ret;
 	unsigned long addr;
@@ -170,8 +187,8 @@
 	if (ret)
 		return ret;
 
-	return memblock_free(addr, size);
-
+	memblock_free_late(addr, size);
+	return 0;
 }
 
 /**
@@ -267,7 +284,7 @@
 				   const char *cmdline, size_t extra_fdt_size)
 {
 	void *fdt;
-	int ret, chosen_node;
+	int ret, chosen_node, len;
 	const void *prop;
 	size_t fdt_size;
 
@@ -310,19 +327,19 @@
 		goto out;
 
 	/* Did we boot using an initrd? */
-	prop = fdt_getprop(fdt, chosen_node, "linux,initrd-start", NULL);
+	prop = fdt_getprop(fdt, chosen_node, "linux,initrd-start", &len);
 	if (prop) {
 		u64 tmp_start, tmp_end, tmp_size;
 
-		tmp_start = fdt64_to_cpu(*((const fdt64_t *) prop));
+		tmp_start = of_read_number(prop, len / 4);
 
-		prop = fdt_getprop(fdt, chosen_node, "linux,initrd-end", NULL);
+		prop = fdt_getprop(fdt, chosen_node, "linux,initrd-end", &len);
 		if (!prop) {
 			ret = -EINVAL;
 			goto out;
 		}
 
-		tmp_end = fdt64_to_cpu(*((const fdt64_t *) prop));
+		tmp_end = of_read_number(prop, len / 4);
 
 		/*
 		 * kexec reserves exact initrd size, while firmware may
@@ -386,6 +403,15 @@
 				crashk_res.end - crashk_res.start + 1);
 		if (ret)
 			goto out;
+
+		if (crashk_low_res.end) {
+			ret = fdt_appendprop_addrrange(fdt, 0, chosen_node,
+					"linux,usable-memory-range",
+					crashk_low_res.start,
+					crashk_low_res.end - crashk_low_res.start + 1);
+			if (ret)
+				goto out;
+		}
 	}
 
 	/* add bootargs */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/of_reserved_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/of_reserved_mem.c
@@ -22,6 +22,7 @@
 #include <linux/slab.h>
 #include <linux/memblock.h>
 #include <linux/kmemleak.h>
+#include <linux/cma.h>
 
 #include "of_private.h"
 
@@ -47,9 +48,11 @@
 		err = memblock_mark_nomap(base, size);
 		if (err)
 			memblock_free(base, size);
-		kmemleak_ignore_phys(base);
 	}
 
+	if (!err)
+		kmemleak_ignore_phys(base);
+
 	return err;
 }
 
@@ -116,12 +119,8 @@
 	if (IS_ENABLED(CONFIG_CMA)
 	    && of_flat_dt_is_compatible(node, "shared-dma-pool")
 	    && of_get_flat_dt_prop(node, "reusable", NULL)
-	    && !nomap) {
-		unsigned long order =
-			max_t(unsigned long, MAX_ORDER - 1, pageblock_order);
-
-		align = max(align, (phys_addr_t)PAGE_SIZE << order);
-	}
+	    && !nomap)
+		align = max_t(phys_addr_t, align, CMA_MIN_ALIGNMENT_BYTES);
 
 	prop = of_get_flat_dt_prop(node, "alloc-ranges", &len);
 	if (prop) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/overlay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/overlay.c
@@ -45,8 +45,8 @@
 
 /**
  * struct fragment - info about fragment nodes in overlay expanded device tree
- * @target:	target of the overlay operation
  * @overlay:	pointer to the __overlay__ node
+ * @target:	target of the overlay operation
  */
 struct fragment {
 	struct device_node *overlay;
@@ -57,8 +57,10 @@
  * struct overlay_changeset
  * @id:			changeset identifier
  * @ovcs_list:		list on which we are located
- * @fdt:		base of memory allocated to hold aligned FDT that was unflattened to create @overlay_tree
- * @overlay_tree:	expanded device tree that contains the fragment nodes
+ * @new_fdt:		Memory allocated to hold unflattened aligned FDT
+ * @overlay_mem:	the memory chunk that contains @overlay_root
+ * @overlay_root:	expanded device tree that contains the fragment nodes
+ * @notify_state:	most recent notify action used on overlay
  * @count:		count of fragment structures
  * @fragments:		fragment nodes in the overlay expanded device tree
  * @symbols_fragment:	last element of @fragments[] is the  __symbols__ node
@@ -67,8 +69,10 @@
 struct overlay_changeset {
 	int id;
 	struct list_head ovcs_list;
-	const void *fdt;
-	struct device_node *overlay_tree;
+	const void *new_fdt;
+	const void *overlay_mem;
+	struct device_node *overlay_root;
+	enum of_overlay_notify_action notify_state;
 	int count;
 	struct fragment *fragments;
 	bool symbols_fragment;
@@ -115,7 +119,6 @@
 	mutex_unlock(&of_overlay_phandle_mutex);
 }
 
-
 static LIST_HEAD(ovcs_list);
 static DEFINE_IDR(ovcs_idr);
 
@@ -149,19 +152,14 @@
 }
 EXPORT_SYMBOL_GPL(of_overlay_notifier_unregister);
 
-static char *of_overlay_action_name[] = {
-	"pre-apply",
-	"post-apply",
-	"pre-remove",
-	"post-remove",
-};
-
 static int overlay_notify(struct overlay_changeset *ovcs,
 		enum of_overlay_notify_action action)
 {
 	struct of_overlay_notify_data nd;
 	int i, ret;
 
+	ovcs->notify_state = action;
+
 	for (i = 0; i < ovcs->count; i++) {
 		struct fragment *fragment = &ovcs->fragments[i];
 
@@ -170,12 +168,10 @@
 
 		ret = blocking_notifier_call_chain(&overlay_notify_chain,
 						   action, &nd);
-		if (ret == NOTIFY_OK || ret == NOTIFY_STOP)
-			return 0;
-		if (ret) {
+		if (notifier_to_errno(ret)) {
 			ret = notifier_to_errno(ret);
 			pr_err("overlay changeset %s notifier error %d, target: %pOF\n",
-			       of_overlay_action_name[action], ret, nd.target);
+			       of_overlay_action_name(action), ret, nd.target);
 			return ret;
 		}
 	}
@@ -185,7 +181,7 @@
 
 /*
  * The values of properties in the "/__symbols__" node are paths in
- * the ovcs->overlay_tree.  When duplicating the properties, the paths
+ * the ovcs->overlay_root.  When duplicating the properties, the paths
  * need to be adjusted to be the correct path for the live device tree.
  *
  * The paths refer to a node in the subtree of a fragment node's "__overlay__"
@@ -221,7 +217,7 @@
 
 	if (path_len < 1)
 		return NULL;
-	fragment_node = __of_find_node_by_path(ovcs->overlay_tree, path + 1);
+	fragment_node = __of_find_node_by_path(ovcs->overlay_root, path + 1);
 	overlay_node = __of_find_node_by_path(fragment_node, "__overlay__/");
 	of_node_put(fragment_node);
 	of_node_put(overlay_node);
@@ -549,7 +545,7 @@
 
 		fn_1 = kasprintf(GFP_KERNEL, "%pOF", ce_1->np);
 		fn_2 = kasprintf(GFP_KERNEL, "%pOF", ce_2->np);
-		node_path_match = !strcmp(fn_1, fn_2);
+		node_path_match = !fn_1 || !fn_2 || !strcmp(fn_1, fn_2);
 		kfree(fn_1);
 		kfree(fn_2);
 		if (node_path_match) {
@@ -584,7 +580,7 @@
 
 		fn_1 = kasprintf(GFP_KERNEL, "%pOF", ce_1->np);
 		fn_2 = kasprintf(GFP_KERNEL, "%pOF", ce_2->np);
-		node_path_match = !strcmp(fn_1, fn_2);
+		node_path_match = !fn_1 || !fn_2 || !strcmp(fn_1, fn_2);
 		kfree(fn_1);
 		kfree(fn_2);
 		if (node_path_match &&
@@ -718,53 +714,48 @@
 
 /**
  * init_overlay_changeset() - initialize overlay changeset from overlay tree
- * @ovcs:	Overlay changeset to build
- * @fdt:	base of memory allocated to hold aligned FDT that was unflattened to create @tree
- * @tree:	Contains the overlay fragments and overlay fixup nodes
+ * @ovcs:		Overlay changeset to build
  *
  * Initialize @ovcs.  Populate @ovcs->fragments with node information from
- * the top level of @tree.  The relevant top level nodes are the fragment
- * nodes and the __symbols__ node.  Any other top level node will be ignored.
+ * the top level of @overlay_root.  The relevant top level nodes are the
+ * fragment nodes and the __symbols__ node.  Any other top level node will
+ * be ignored.  Populate other @ovcs fields.
  *
  * Return: 0 on success, -ENOMEM if memory allocation failure, -EINVAL if error
- * detected in @tree, or -ENOSPC if idr_alloc() error.
+ * detected in @overlay_root.  On error return, the caller of
+ * init_overlay_changeset() must call free_overlay_changeset().
  */
-static int init_overlay_changeset(struct overlay_changeset *ovcs,
-		const void *fdt, struct device_node *tree)
+static int init_overlay_changeset(struct overlay_changeset *ovcs)
 {
 	struct device_node *node, *overlay_node;
 	struct fragment *fragment;
 	struct fragment *fragments;
-	int cnt, id, ret;
+	int cnt, ret;
+
+	/*
+	 * None of the resources allocated by this function will be freed in
+	 * the error paths.  Instead the caller of this function is required
+	 * to call free_overlay_changeset() (which will free the resources)
+	 * if error return.
+	 */
 
 	/*
 	 * Warn for some issues.  Can not return -EINVAL for these until
 	 * of_unittest_apply_overlay() is fixed to pass these checks.
 	 */
-	if (!of_node_check_flag(tree, OF_DYNAMIC))
-		pr_debug("%s() tree is not dynamic\n", __func__);
+	if (!of_node_check_flag(ovcs->overlay_root, OF_DYNAMIC))
+		pr_debug("%s() ovcs->overlay_root is not dynamic\n", __func__);
 
-	if (!of_node_check_flag(tree, OF_DETACHED))
-		pr_debug("%s() tree is not detached\n", __func__);
+	if (!of_node_check_flag(ovcs->overlay_root, OF_DETACHED))
+		pr_debug("%s() ovcs->overlay_root is not detached\n", __func__);
 
-	if (!of_node_is_root(tree))
-		pr_debug("%s() tree is not root\n", __func__);
-
-	ovcs->overlay_tree = tree;
-	ovcs->fdt = fdt;
-
-	INIT_LIST_HEAD(&ovcs->ovcs_list);
-
-	of_changeset_init(&ovcs->cset);
-
-	id = idr_alloc(&ovcs_idr, ovcs, 1, 0, GFP_KERNEL);
-	if (id <= 0)
-		return id;
+	if (!of_node_is_root(ovcs->overlay_root))
+		pr_debug("%s() ovcs->overlay_root is not root\n", __func__);
 
 	cnt = 0;
 
 	/* fragment nodes */
-	for_each_child_of_node(tree, node) {
+	for_each_child_of_node(ovcs->overlay_root, node) {
 		overlay_node = of_get_child_by_name(node, "__overlay__");
 		if (overlay_node) {
 			cnt++;
@@ -772,7 +763,7 @@
 		}
 	}
 
-	node = of_get_child_by_name(tree, "__symbols__");
+	node = of_get_child_by_name(ovcs->overlay_root, "__symbols__");
 	if (node) {
 		cnt++;
 		of_node_put(node);
@@ -781,11 +772,12 @@
 	fragments = kcalloc(cnt, sizeof(*fragments), GFP_KERNEL);
 	if (!fragments) {
 		ret = -ENOMEM;
-		goto err_free_idr;
+		goto err_out;
 	}
+	ovcs->fragments = fragments;
 
 	cnt = 0;
-	for_each_child_of_node(tree, node) {
+	for_each_child_of_node(ovcs->overlay_root, node) {
 		overlay_node = of_get_child_by_name(node, "__overlay__");
 		if (!overlay_node)
 			continue;
@@ -797,7 +789,7 @@
 			of_node_put(fragment->overlay);
 			ret = -EINVAL;
 			of_node_put(node);
-			goto err_free_fragments;
+			goto err_out;
 		}
 
 		cnt++;
@@ -807,7 +799,7 @@
 	 * if there is a symbols fragment in ovcs->fragments[i] it is
 	 * the final element in the array
 	 */
-	node = of_get_child_by_name(tree, "__symbols__");
+	node = of_get_child_by_name(ovcs->overlay_root, "__symbols__");
 	if (node) {
 		ovcs->symbols_fragment = 1;
 		fragment = &fragments[cnt];
@@ -817,7 +809,8 @@
 		if (!fragment->target) {
 			pr_err("symbols in overlay, but not in live tree\n");
 			ret = -EINVAL;
-			goto err_free_fragments;
+			of_node_put(node);
+			goto err_out;
 		}
 
 		cnt++;
@@ -826,20 +819,14 @@
 	if (!cnt) {
 		pr_err("no fragments or symbols in overlay\n");
 		ret = -EINVAL;
-		goto err_free_fragments;
+		goto err_out;
 	}
 
-	ovcs->id = id;
 	ovcs->count = cnt;
-	ovcs->fragments = fragments;
 
 	return 0;
 
-err_free_fragments:
-	kfree(fragments);
-err_free_idr:
-	idr_remove(&ovcs_idr, id);
-
+err_out:
 	pr_err("%s() failed, ret = %d\n", __func__, ret);
 
 	return ret;
@@ -852,21 +839,34 @@
 	if (ovcs->cset.entries.next)
 		of_changeset_destroy(&ovcs->cset);
 
-	if (ovcs->id)
+	if (ovcs->id) {
 		idr_remove(&ovcs_idr, ovcs->id);
+		list_del(&ovcs->ovcs_list);
+		ovcs->id = 0;
+	}
+
 
 	for (i = 0; i < ovcs->count; i++) {
 		of_node_put(ovcs->fragments[i].target);
 		of_node_put(ovcs->fragments[i].overlay);
 	}
 	kfree(ovcs->fragments);
+
 	/*
-	 * There should be no live pointers into ovcs->overlay_tree and
-	 * ovcs->fdt due to the policy that overlay notifiers are not allowed
-	 * to retain pointers into the overlay devicetree.
+	 * There should be no live pointers into ovcs->overlay_mem and
+	 * ovcs->new_fdt due to the policy that overlay notifiers are not
+	 * allowed to retain pointers into the overlay devicetree other
+	 * than during the window from OF_OVERLAY_PRE_APPLY overlay
+	 * notifiers until the OF_OVERLAY_POST_REMOVE overlay notifiers.
+	 *
+	 * A memory leak will occur here if within the window.
 	 */
-	kfree(ovcs->overlay_tree);
-	kfree(ovcs->fdt);
+
+	if (ovcs->notify_state == OF_OVERLAY_INIT ||
+	    ovcs->notify_state == OF_OVERLAY_POST_REMOVE) {
+		kfree(ovcs->overlay_mem);
+		kfree(ovcs->new_fdt);
+	}
 	kfree(ovcs);
 }
 
@@ -874,28 +874,13 @@
  * internal documentation
  *
  * of_overlay_apply() - Create and apply an overlay changeset
- * @fdt:	base of memory allocated to hold the aligned FDT
- * @tree:	Expanded overlay device tree
- * @ovcs_id:	Pointer to overlay changeset id
+ * @ovcs:	overlay changeset
  *
  * Creates and applies an overlay changeset.
  *
- * If an error occurs in a pre-apply notifier, then no changes are made
- * to the device tree.
- *
-
- * A non-zero return value will not have created the changeset if error is from:
- *   - parameter checks
- *   - building the changeset
- *   - overlay changeset pre-apply notifier
- *
  * If an error is returned by an overlay changeset pre-apply notifier
  * then no further overlay changeset pre-apply notifier will be called.
  *
- * A non-zero return value will have created the changeset if error is from:
- *   - overlay changeset entry notifier
- *   - overlay changeset post-apply notifier
- *
  * If an error is returned by an overlay changeset post-apply notifier
  * then no further overlay changeset post-apply notifier will be called.
  *
@@ -909,64 +894,35 @@
  * following attempt to apply or remove an overlay changeset will be
  * refused.
  *
- * Returns 0 on success, or a negative error number.  Overlay changeset
- * id is returned to *ovcs_id.
+ * Returns 0 on success, or a negative error number.  On error return,
+ * the caller of of_overlay_apply() must call free_overlay_changeset().
  */
 
-static int of_overlay_apply(const void *fdt, struct device_node *tree,
-		int *ovcs_id)
+static int of_overlay_apply(struct overlay_changeset *ovcs)
 {
-	struct overlay_changeset *ovcs;
 	int ret = 0, ret_revert, ret_tmp;
 
-	/*
-	 * As of this point, fdt and tree belong to the overlay changeset.
-	 * overlay changeset code is responsible for freeing them.
-	 */
-
 	if (devicetree_corrupt()) {
 		pr_err("devicetree state suspect, refuse to apply overlay\n");
-		kfree(fdt);
-		kfree(tree);
 		ret = -EBUSY;
 		goto out;
 	}
 
-	ovcs = kzalloc(sizeof(*ovcs), GFP_KERNEL);
-	if (!ovcs) {
-		kfree(fdt);
-		kfree(tree);
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	of_overlay_mutex_lock();
-	mutex_lock(&of_mutex);
-
-	ret = of_resolve_phandles(tree);
+	ret = of_resolve_phandles(ovcs->overlay_root);
 	if (ret)
-		goto err_free_tree;
+		goto out;
 
-	ret = init_overlay_changeset(ovcs, fdt, tree);
+	ret = init_overlay_changeset(ovcs);
 	if (ret)
-		goto err_free_tree;
+		goto out;
 
-	/*
-	 * after overlay_notify(), ovcs->overlay_tree related pointers may have
-	 * leaked to drivers, so can not kfree() tree, aka ovcs->overlay_tree;
-	 * and can not free memory containing aligned fdt.  The aligned fdt
-	 * is contained within the memory at ovcs->fdt, possibly at an offset
-	 * from ovcs->fdt.
-	 */
 	ret = overlay_notify(ovcs, OF_OVERLAY_PRE_APPLY);
-	if (ret) {
-		pr_err("overlay changeset pre-apply notify error %d\n", ret);
-		goto err_free_overlay_changeset;
-	}
+	if (ret)
+		goto out;
 
 	ret = build_changeset(ovcs);
 	if (ret)
-		goto err_free_overlay_changeset;
+		goto out;
 
 	ret_revert = 0;
 	ret = __of_changeset_apply_entries(&ovcs->cset, &ret_revert);
@@ -976,7 +932,7 @@
 				 ret_revert);
 			devicetree_state_flags |= DTSF_APPLY_FAIL;
 		}
-		goto err_free_overlay_changeset;
+		goto out;
 	}
 
 	ret = __of_changeset_apply_notify(&ovcs->cset);
@@ -984,29 +940,10 @@
 		pr_err("overlay apply changeset entry notify error %d\n", ret);
 	/* notify failure is not fatal, continue */
 
-	list_add_tail(&ovcs->ovcs_list, &ovcs_list);
-	*ovcs_id = ovcs->id;
-
 	ret_tmp = overlay_notify(ovcs, OF_OVERLAY_POST_APPLY);
-	if (ret_tmp) {
-		pr_err("overlay changeset post-apply notify error %d\n",
-		       ret_tmp);
+	if (ret_tmp)
 		if (!ret)
 			ret = ret_tmp;
-	}
-
-	goto out_unlock;
-
-err_free_tree:
-	kfree(fdt);
-	kfree(tree);
-
-err_free_overlay_changeset:
-	free_overlay_changeset(ovcs);
-
-out_unlock:
-	mutex_unlock(&of_mutex);
-	of_overlay_mutex_unlock();
 
 out:
 	pr_debug("%s() err=%d\n", __func__, ret);
@@ -1015,15 +952,16 @@
 }
 
 int of_overlay_fdt_apply(const void *overlay_fdt, u32 overlay_fdt_size,
-			 int *ovcs_id)
+			 int *ret_ovcs_id)
 {
 	void *new_fdt;
 	void *new_fdt_align;
+	void *overlay_mem;
 	int ret;
 	u32 size;
-	struct device_node *overlay_root = NULL;
+	struct overlay_changeset *ovcs;
 
-	*ovcs_id = 0;
+	*ret_ovcs_id = 0;
 
 	if (overlay_fdt_size < sizeof(struct fdt_header) ||
 	    fdt_check_header(overlay_fdt)) {
@@ -1035,41 +973,68 @@
 	if (overlay_fdt_size < size)
 		return -EINVAL;
 
+	ovcs = kzalloc(sizeof(*ovcs), GFP_KERNEL);
+	if (!ovcs)
+		return -ENOMEM;
+
+	of_overlay_mutex_lock();
+	mutex_lock(&of_mutex);
+
+	/*
+	 * ovcs->notify_state must be set to OF_OVERLAY_INIT before allocating
+	 * ovcs resources, implicitly set by kzalloc() of ovcs
+	 */
+
+	ovcs->id = idr_alloc(&ovcs_idr, ovcs, 1, 0, GFP_KERNEL);
+	if (ovcs->id <= 0) {
+		ret = ovcs->id;
+		goto err_free_ovcs;
+	}
+
+	INIT_LIST_HEAD(&ovcs->ovcs_list);
+	list_add_tail(&ovcs->ovcs_list, &ovcs_list);
+	of_changeset_init(&ovcs->cset);
+
 	/*
 	 * Must create permanent copy of FDT because of_fdt_unflatten_tree()
 	 * will create pointers to the passed in FDT in the unflattened tree.
 	 */
 	new_fdt = kmalloc(size + FDT_ALIGN_SIZE, GFP_KERNEL);
-	if (!new_fdt)
-		return -ENOMEM;
+	if (!new_fdt) {
+		ret = -ENOMEM;
+		goto err_free_ovcs;
+	}
+	ovcs->new_fdt = new_fdt;
 
 	new_fdt_align = PTR_ALIGN(new_fdt, FDT_ALIGN_SIZE);
 	memcpy(new_fdt_align, overlay_fdt, size);
 
-	of_fdt_unflatten_tree(new_fdt_align, NULL, &overlay_root);
-	if (!overlay_root) {
+	overlay_mem = of_fdt_unflatten_tree(new_fdt_align, NULL,
+					    &ovcs->overlay_root);
+	if (!overlay_mem) {
 		pr_err("unable to unflatten overlay_fdt\n");
 		ret = -EINVAL;
-		goto out_free_new_fdt;
+		goto err_free_ovcs;
 	}
+	ovcs->overlay_mem = overlay_mem;
 
-	ret = of_overlay_apply(new_fdt, overlay_root, ovcs_id);
-	if (ret < 0) {
-		/*
-		 * new_fdt and overlay_root now belong to the overlay
-		 * changeset.
-		 * overlay changeset code is responsible for freeing them.
-		 */
-		goto out;
-	}
+	ret = of_overlay_apply(ovcs);
+	if (ret < 0)
+		goto err_free_ovcs;
+
+	mutex_unlock(&of_mutex);
+	of_overlay_mutex_unlock();
+
+	*ret_ovcs_id = ovcs->id;
 
 	return 0;
 
+err_free_ovcs:
+	free_overlay_changeset(ovcs);
 
-out_free_new_fdt:
-	kfree(new_fdt);
+	mutex_unlock(&of_mutex);
+	of_overlay_mutex_unlock();
 
-out:
 	return ret;
 }
 EXPORT_SYMBOL_GPL(of_overlay_fdt_apply);
@@ -1206,28 +1171,24 @@
 	if (!ovcs) {
 		ret = -ENODEV;
 		pr_err("remove: Could not find overlay #%d\n", *ovcs_id);
-		goto out_unlock;
+		goto err_unlock;
 	}
 
 	if (!overlay_removal_is_ok(ovcs)) {
 		ret = -EBUSY;
-		goto out_unlock;
+		goto err_unlock;
 	}
 
 	ret = overlay_notify(ovcs, OF_OVERLAY_PRE_REMOVE);
-	if (ret) {
-		pr_err("overlay changeset pre-remove notify error %d\n", ret);
-		goto out_unlock;
-	}
-
-	list_del(&ovcs->ovcs_list);
+	if (ret)
+		goto err_unlock;
 
 	ret_apply = 0;
 	ret = __of_changeset_revert_entries(&ovcs->cset, &ret_apply);
 	if (ret) {
 		if (ret_apply)
 			devicetree_state_flags |= DTSF_REVERT_FAIL;
-		goto out_unlock;
+		goto err_unlock;
 	}
 
 	ret = __of_changeset_revert_notify(&ovcs->cset);
@@ -1237,17 +1198,27 @@
 
 	*ovcs_id = 0;
 
+	/*
+	 * Note that the overlay memory will be kfree()ed by
+	 * free_overlay_changeset() even if the notifier for
+	 * OF_OVERLAY_POST_REMOVE returns an error.
+	 */
 	ret_tmp = overlay_notify(ovcs, OF_OVERLAY_POST_REMOVE);
-	if (ret_tmp) {
-		pr_err("overlay changeset post-remove notify error %d\n",
-		       ret_tmp);
+	if (ret_tmp)
 		if (!ret)
 			ret = ret_tmp;
-	}
+
+	/* Wait for completion of call_rcu()'s */
+	rcu_barrier();
 
 	free_overlay_changeset(ovcs);
 
-out_unlock:
+err_unlock:
+	/*
+	 * If jumped over free_overlay_changeset(), then did not kfree()
+	 * overlay related memory.  This is a memory leak unless a subsequent
+	 * of_overlay_remove() of this overlay is successful.
+	 */
 	mutex_unlock(&of_mutex);
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/property.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/property.c
@@ -975,8 +975,10 @@
 						       nargs, index, &of_args);
 	if (ret < 0)
 		return ret;
-	if (!args)
+	if (!args) {
+		of_node_put(of_args.np);
 		return 0;
+	}
 
 	args->nargs = of_args.args_count;
 	args->fwnode = of_fwnode_handle(of_args.np);
@@ -1268,7 +1270,7 @@
 DEFINE_SIMPLE_PROP(interconnects, "interconnects", "#interconnect-cells")
 DEFINE_SIMPLE_PROP(iommus, "iommus", "#iommu-cells")
 DEFINE_SIMPLE_PROP(mboxes, "mboxes", "#mbox-cells")
-DEFINE_SIMPLE_PROP(io_channels, "io-channel", "#io-channel-cells")
+DEFINE_SIMPLE_PROP(io_channels, "io-channels", "#io-channel-cells")
 DEFINE_SIMPLE_PROP(interrupt_parent, "interrupt-parent", NULL)
 DEFINE_SIMPLE_PROP(dmas, "dmas", "#dma-cells")
 DEFINE_SIMPLE_PROP(power_domains, "power-domains", "#power-domain-cells")
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/unittest-data/tests-address.dtsi
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/unittest-data/tests-address.dtsi
@@ -14,7 +14,7 @@
 			#size-cells = <1>;
 			/* ranges here is to make sure we don't use it for
 			 * dma-ranges translation */
-			ranges = <0x70000000 0x70000000 0x40000000>,
+			ranges = <0x70000000 0x70000000 0x50000000>,
 				 <0x00000000 0xd0000000 0x20000000>;
 			dma-ranges = <0x0 0x20000000 0x40000000>;
 
@@ -43,6 +43,13 @@
 					     <0x42000000 0x0 0xc0000000 0x20000000 0x0 0x10000000>;
 			};
 
+			bus@a0000000 {
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges = <0xf00baa 0x0 0x0 0xa0000000 0x0 0x100000>,
+					 <0xf00bee 0x1 0x0 0xb0000000 0x0 0x200000>;
+			};
+
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/unittest-data/tests-phandle.dtsi
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/unittest-data/tests-phandle.dtsi
@@ -38,6 +38,13 @@
 				phandle-map-pass-thru = <0x0 0xf0>;
 			};
 
+			provider5: provider5 {
+				#phandle-cells = <2>;
+				phandle-map = <2 7 &provider4 2 3>;
+				phandle-map-mask = <0xff 0xf>;
+				phandle-map-pass-thru = <0x0 0xf0>;
+			};
+
 			consumer-a {
 				phandle-list =	<&provider1 1>,
 						<&provider2 2 0>,
@@ -64,7 +71,8 @@
 						<&provider4 4 0x100>,
 						<&provider4 0 0x61>,
 						<&provider0>,
-						<&provider4 19 0x20>;
+						<&provider4 19 0x20>,
+						<&provider5 2 7>;
 				phandle-list-bad-phandle = <12345678 0 0>;
 				phandle-list-bad-args = <&provider2 1 0>,
 							<&provider4 0>;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/of/unittest.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/of/unittest.c
@@ -49,6 +49,12 @@
 	failed; \
 })
 
+#ifdef CONFIG_OF_KOBJ
+#define OF_KREF_READ(NODE) kref_read(&(NODE)->kobj.kref)
+#else
+#define OF_KREF_READ(NODE) 1
+#endif
+
 /*
  * Expected message may have a message level other than KERN_INFO.
  * Print the expected message only if the current loglevel will allow
@@ -70,7 +76,7 @@
 
 	np = of_find_node_by_path("/testcase-data");
 	name = kasprintf(GFP_KERNEL, "%pOF", np);
-	unittest(np && !strcmp("/testcase-data", name),
+	unittest(np && name && !strcmp("/testcase-data", name),
 		"find /testcase-data failed\n");
 	of_node_put(np);
 	kfree(name);
@@ -81,14 +87,14 @@
 
 	np = of_find_node_by_path("/testcase-data/phandle-tests/consumer-a");
 	name = kasprintf(GFP_KERNEL, "%pOF", np);
-	unittest(np && !strcmp("/testcase-data/phandle-tests/consumer-a", name),
+	unittest(np && name && !strcmp("/testcase-data/phandle-tests/consumer-a", name),
 		"find /testcase-data/phandle-tests/consumer-a failed\n");
 	of_node_put(np);
 	kfree(name);
 
 	np = of_find_node_by_path("testcase-alias");
 	name = kasprintf(GFP_KERNEL, "%pOF", np);
-	unittest(np && !strcmp("/testcase-data", name),
+	unittest(np && name && !strcmp("/testcase-data", name),
 		"find testcase-alias failed\n");
 	of_node_put(np);
 	kfree(name);
@@ -99,7 +105,7 @@
 
 	np = of_find_node_by_path("testcase-alias/phandle-tests/consumer-a");
 	name = kasprintf(GFP_KERNEL, "%pOF", np);
-	unittest(np && !strcmp("/testcase-data/phandle-tests/consumer-a", name),
+	unittest(np && name && !strcmp("/testcase-data/phandle-tests/consumer-a", name),
 		"find testcase-alias/phandle-tests/consumer-a failed\n");
 	of_node_put(np);
 	kfree(name);
@@ -448,6 +454,9 @@
 
 		unittest(passed, "index %i - data error on node %pOF rc=%i\n",
 			 i, args.np, rc);
+
+		if (rc == 0)
+			of_node_put(args.np);
 	}
 
 	/* Check for missing list property */
@@ -537,8 +546,9 @@
 
 static void __init of_unittest_parse_phandle_with_args_map(void)
 {
-	struct device_node *np, *p0, *p1, *p2, *p3;
+	struct device_node *np, *p[6] = {};
 	struct of_phandle_args args;
+	unsigned int prefs[6];
 	int i, rc;
 
 	np = of_find_node_by_path("/testcase-data/phandle-tests/consumer-b");
@@ -547,34 +557,24 @@
 		return;
 	}
 
-	p0 = of_find_node_by_path("/testcase-data/phandle-tests/provider0");
-	if (!p0) {
-		pr_err("missing testcase data\n");
-		return;
-	}
-
-	p1 = of_find_node_by_path("/testcase-data/phandle-tests/provider1");
-	if (!p1) {
-		pr_err("missing testcase data\n");
-		return;
-	}
-
-	p2 = of_find_node_by_path("/testcase-data/phandle-tests/provider2");
-	if (!p2) {
-		pr_err("missing testcase data\n");
-		return;
-	}
-
-	p3 = of_find_node_by_path("/testcase-data/phandle-tests/provider3");
-	if (!p3) {
-		pr_err("missing testcase data\n");
-		return;
+	p[0] = of_find_node_by_path("/testcase-data/phandle-tests/provider0");
+	p[1] = of_find_node_by_path("/testcase-data/phandle-tests/provider1");
+	p[2] = of_find_node_by_path("/testcase-data/phandle-tests/provider2");
+	p[3] = of_find_node_by_path("/testcase-data/phandle-tests/provider3");
+	p[4] = of_find_node_by_path("/testcase-data/phandle-tests/provider4");
+	p[5] = of_find_node_by_path("/testcase-data/phandle-tests/provider5");
+	for (i = 0; i < ARRAY_SIZE(p); ++i) {
+		if (!p[i]) {
+			pr_err("missing testcase data\n");
+			return;
+		}
+		prefs[i] = OF_KREF_READ(p[i]);
 	}
 
 	rc = of_count_phandle_with_args(np, "phandle-list", "#phandle-cells");
-	unittest(rc == 7, "of_count_phandle_with_args() returned %i, expected 7\n", rc);
+	unittest(rc == 8, "of_count_phandle_with_args() returned %i, expected 8\n", rc);
 
-	for (i = 0; i < 8; i++) {
+	for (i = 0; i < 9; i++) {
 		bool passed = true;
 
 		memset(&args, 0, sizeof(args));
@@ -585,13 +585,13 @@
 		switch (i) {
 		case 0:
 			passed &= !rc;
-			passed &= (args.np == p1);
+			passed &= (args.np == p[1]);
 			passed &= (args.args_count == 1);
 			passed &= (args.args[0] == 1);
 			break;
 		case 1:
 			passed &= !rc;
-			passed &= (args.np == p3);
+			passed &= (args.np == p[3]);
 			passed &= (args.args_count == 3);
 			passed &= (args.args[0] == 2);
 			passed &= (args.args[1] == 5);
@@ -602,28 +602,36 @@
 			break;
 		case 3:
 			passed &= !rc;
-			passed &= (args.np == p0);
+			passed &= (args.np == p[0]);
 			passed &= (args.args_count == 0);
 			break;
 		case 4:
 			passed &= !rc;
-			passed &= (args.np == p1);
+			passed &= (args.np == p[1]);
 			passed &= (args.args_count == 1);
 			passed &= (args.args[0] == 3);
 			break;
 		case 5:
 			passed &= !rc;
-			passed &= (args.np == p0);
+			passed &= (args.np == p[0]);
 			passed &= (args.args_count == 0);
 			break;
 		case 6:
 			passed &= !rc;
-			passed &= (args.np == p2);
+			passed &= (args.np == p[2]);
 			passed &= (args.args_count == 2);
 			passed &= (args.args[0] == 15);
 			passed &= (args.args[1] == 0x20);
 			break;
 		case 7:
+			passed &= !rc;
+			passed &= (args.np == p[3]);
+			passed &= (args.args_count == 3);
+			passed &= (args.args[0] == 2);
+			passed &= (args.args[1] == 5);
+			passed &= (args.args[2] == 3);
+			break;
+		case 8:
 			passed &= (rc == -ENOENT);
 			break;
 		default:
@@ -632,6 +640,9 @@
 
 		unittest(passed, "index %i - data error on node %s rc=%i\n",
 			 i, args.np->full_name, rc);
+
+		if (rc == 0)
+			of_node_put(args.np);
 	}
 
 	/* Check for missing list property */
@@ -657,12 +668,12 @@
 	memset(&args, 0, sizeof(args));
 
 	EXPECT_BEGIN(KERN_INFO,
-		     "OF: /testcase-data/phandle-tests/consumer-b: could not find phandle");
+		     "OF: /testcase-data/phandle-tests/consumer-b: could not find phandle 12345678");
 
 	rc = of_parse_phandle_with_args_map(np, "phandle-list-bad-phandle",
 					    "phandle", 0, &args);
 	EXPECT_END(KERN_INFO,
-		   "OF: /testcase-data/phandle-tests/consumer-b: could not find phandle");
+		   "OF: /testcase-data/phandle-tests/consumer-b: could not find phandle 12345678");
 
 	unittest(rc == -EINVAL, "expected:%i got:%i\n", -EINVAL, rc);
 
@@ -678,6 +689,13 @@
 		   "OF: /testcase-data/phandle-tests/consumer-b: #phandle-cells = 2 found -1");
 
 	unittest(rc == -EINVAL, "expected:%i got:%i\n", -EINVAL, rc);
+
+	for (i = 0; i < ARRAY_SIZE(p); ++i) {
+		unittest(prefs[i] == OF_KREF_READ(p[i]),
+			 "provider%d: expected:%d got:%d\n",
+			 i, prefs[i], OF_KREF_READ(p[i]));
+		of_node_put(p[i]);
+	}
 }
 
 static void __init of_unittest_property_string(void)
@@ -911,11 +929,18 @@
 	if (!rc) {
 		phys_addr_t	paddr;
 		dma_addr_t	dma_addr;
-		struct device	dev_bogus;
+		struct device	*dev_bogus;
+
+		dev_bogus = kzalloc(sizeof(struct device), GFP_KERNEL);
+		if (!dev_bogus) {
+			unittest(0, "kzalloc() failed\n");
+			kfree(map);
+			return;
+		}
 
-		dev_bogus.dma_range_map = map;
-		paddr = dma_to_phys(&dev_bogus, expect_dma_addr);
-		dma_addr = phys_to_dma(&dev_bogus, expect_paddr);
+		dev_bogus->dma_range_map = map;
+		paddr = dma_to_phys(dev_bogus, expect_dma_addr);
+		dma_addr = phys_to_dma(dev_bogus, expect_paddr);
 
 		unittest(paddr == expect_paddr,
 			 "of_dma_get_range: wrong phys addr %pap (expecting %llx) on node %pOF\n",
@@ -925,6 +950,7 @@
 			 &dma_addr, expect_dma_addr, np);
 
 		kfree(map);
+		kfree(dev_bogus);
 	}
 	of_node_put(np);
 #endif
@@ -934,8 +960,9 @@
 {
 	of_unittest_dma_ranges_one("/testcase-data/address-tests/device@70000000",
 		0x0, 0x20000000);
-	of_unittest_dma_ranges_one("/testcase-data/address-tests/bus@80000000/device@1000",
-		0x100000000, 0x20000000);
+	if (IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT))
+		of_unittest_dma_ranges_one("/testcase-data/address-tests/bus@80000000/device@1000",
+			0x100000000, 0x20000000);
 	of_unittest_dma_ranges_one("/testcase-data/address-tests/pci@90000000",
 		0x80000000, 0x20000000);
 }
@@ -992,6 +1019,113 @@
 	of_node_put(np);
 }
 
+static void __init of_unittest_bus_ranges(void)
+{
+	struct device_node *np;
+	struct of_range range;
+	struct of_range_parser parser;
+	int i = 0;
+
+	np = of_find_node_by_path("/testcase-data/address-tests");
+	if (!np) {
+		pr_err("missing testcase data\n");
+		return;
+	}
+
+	if (of_range_parser_init(&parser, np)) {
+		pr_err("missing ranges property\n");
+		return;
+	}
+
+	/*
+	 * Get the "ranges" from the device tree
+	 */
+	for_each_of_range(&parser, &range) {
+		unittest(range.flags == IORESOURCE_MEM,
+			"for_each_of_range wrong flags on node %pOF flags=%x (expected %x)\n",
+			np, range.flags, IORESOURCE_MEM);
+		if (!i) {
+			unittest(range.size == 0x50000000,
+				 "for_each_of_range wrong size on node %pOF size=%llx\n",
+				 np, range.size);
+			unittest(range.cpu_addr == 0x70000000,
+				 "for_each_of_range wrong CPU addr (%llx) on node %pOF",
+				 range.cpu_addr, np);
+			unittest(range.bus_addr == 0x70000000,
+				 "for_each_of_range wrong bus addr (%llx) on node %pOF",
+				 range.pci_addr, np);
+		} else {
+			unittest(range.size == 0x20000000,
+				 "for_each_of_range wrong size on node %pOF size=%llx\n",
+				 np, range.size);
+			unittest(range.cpu_addr == 0xd0000000,
+				 "for_each_of_range wrong CPU addr (%llx) on node %pOF",
+				 range.cpu_addr, np);
+			unittest(range.bus_addr == 0x00000000,
+				 "for_each_of_range wrong bus addr (%llx) on node %pOF",
+				 range.pci_addr, np);
+		}
+		i++;
+	}
+
+	of_node_put(np);
+}
+
+static void __init of_unittest_bus_3cell_ranges(void)
+{
+	struct device_node *np;
+	struct of_range range;
+	struct of_range_parser parser;
+	int i = 0;
+
+	np = of_find_node_by_path("/testcase-data/address-tests/bus@a0000000");
+	if (!np) {
+		pr_err("missing testcase data\n");
+		return;
+	}
+
+	if (of_range_parser_init(&parser, np)) {
+		pr_err("missing ranges property\n");
+		return;
+	}
+
+	/*
+	 * Get the "ranges" from the device tree
+	 */
+	for_each_of_range(&parser, &range) {
+		if (!i) {
+			unittest(range.flags == 0xf00baa,
+				 "for_each_of_range wrong flags on node %pOF flags=%x\n",
+				 np, range.flags);
+			unittest(range.size == 0x100000,
+				 "for_each_of_range wrong size on node %pOF size=%llx\n",
+				 np, range.size);
+			unittest(range.cpu_addr == 0xa0000000,
+				 "for_each_of_range wrong CPU addr (%llx) on node %pOF",
+				 range.cpu_addr, np);
+			unittest(range.bus_addr == 0x0,
+				 "for_each_of_range wrong bus addr (%llx) on node %pOF",
+				 range.pci_addr, np);
+		} else {
+			unittest(range.flags == 0xf00bee,
+				 "for_each_of_range wrong flags on node %pOF flags=%x\n",
+				 np, range.flags);
+			unittest(range.size == 0x200000,
+				 "for_each_of_range wrong size on node %pOF size=%llx\n",
+				 np, range.size);
+			unittest(range.cpu_addr == 0xb0000000,
+				 "for_each_of_range wrong CPU addr (%llx) on node %pOF",
+				 range.cpu_addr, np);
+			unittest(range.bus_addr == 0x100000000,
+				 "for_each_of_range wrong bus addr (%llx) on node %pOF",
+				 range.pci_addr, np);
+		}
+		i++;
+	}
+
+	of_node_put(np);
+}
+
 static void __init of_unittest_parse_interrupts(void)
 {
 	struct device_node *np;
@@ -1364,6 +1498,8 @@
 	const char *full_name;
 
 	full_name = kasprintf(GFP_KERNEL, "%pOF", np);
+	if (!full_name)
+		return;
 
 	if (!strcmp(full_name, "/__local_fixups__") ||
 	    !strcmp(full_name, "/__fixups__")) {
@@ -1688,19 +1824,19 @@
 	 */
 
 	EXPECT_BEGIN(KERN_INFO,
-		     "GPIO line <<int>> (line-B-input) hogged as input\n");
+		     "gpio-<<int>> (line-B-input): hogged as input\n");
 
 	EXPECT_BEGIN(KERN_INFO,
-		     "GPIO line <<int>> (line-A-input) hogged as input\n");
+		     "gpio-<<int>> (line-A-input): hogged as input\n");
 
 	ret = platform_driver_register(&unittest_gpio_driver);
 	if (unittest(ret == 0, "could not register unittest gpio driver\n"))
 		return;
 
 	EXPECT_END(KERN_INFO,
-		   "GPIO line <<int>> (line-A-input) hogged as input\n");
+		   "gpio-<<int>> (line-A-input): hogged as input\n");
 	EXPECT_END(KERN_INFO,
-		   "GPIO line <<int>> (line-B-input) hogged as input\n");
+		   "gpio-<<int>> (line-B-input): hogged as input\n");
 
 	unittest(probe_pass_count + 2 == unittest_gpio_probe_pass_count,
 		 "unittest_gpio_probe() failed or not called\n");
@@ -1727,7 +1863,7 @@
 	chip_request_count = unittest_gpio_chip_request_count;
 
 	EXPECT_BEGIN(KERN_INFO,
-		     "GPIO line <<int>> (line-D-input) hogged as input\n");
+		     "gpio-<<int>> (line-D-input): hogged as input\n");
 
 	/* overlay_gpio_03 contains gpio node and child gpio hog node */
 
@@ -1735,7 +1871,7 @@
 		 "Adding overlay 'overlay_gpio_03' failed\n");
 
 	EXPECT_END(KERN_INFO,
-		   "GPIO line <<int>> (line-D-input) hogged as input\n");
+		   "gpio-<<int>> (line-D-input): hogged as input\n");
 
 	unittest(probe_pass_count + 1 == unittest_gpio_probe_pass_count,
 		 "unittest_gpio_probe() failed or not called\n");
@@ -1774,7 +1910,7 @@
 	 */
 
 	EXPECT_BEGIN(KERN_INFO,
-		     "GPIO line <<int>> (line-C-input) hogged as input\n");
+		     "gpio-<<int>> (line-C-input): hogged as input\n");
 
 	/* overlay_gpio_04b contains child gpio hog node */
 
@@ -1782,7 +1918,7 @@
 		 "Adding overlay 'overlay_gpio_04b' failed\n");
 
 	EXPECT_END(KERN_INFO,
-		   "GPIO line <<int>> (line-C-input) hogged as input\n");
+		   "gpio-<<int>> (line-C-input): hogged as input\n");
 
 	unittest(chip_request_count + 1 == unittest_gpio_chip_request_count,
 		 "unittest_gpio_chip_request() called %d times (expected 1 time)\n",
@@ -2062,7 +2198,7 @@
 	of_unittest_untrack_overlay(save_id);
 
 	/* unittest device must be again in before state */
-	if (of_unittest_device_exists(unittest_nr, PDEV_OVERLAY) != before) {
+	if (of_unittest_device_exists(unittest_nr, ovtype) != before) {
 		unittest(0, "%s with device @\"%s\" %s\n",
 				overlay_name_from_nr(overlay_nr),
 				unittest_path(unittest_nr, ovtype),
@@ -3295,6 +3431,8 @@
 	of_unittest_dma_get_max_cpu_address();
 	of_unittest_parse_dma_ranges();
 	of_unittest_pci_dma_ranges();
+	of_unittest_bus_ranges();
+	of_unittest_bus_3cell_ranges();
 	of_unittest_match_node();
 	of_unittest_platform_populate();
 	of_unittest_overlay();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/opp/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/opp/core.c
@@ -1249,7 +1249,10 @@
 	return opp_table;
 
 remove_opp_dev:
+	_of_clear_opp_table(opp_table);
 	_remove_opp_dev(opp_dev, opp_table);
+	mutex_destroy(&opp_table->genpd_virt_dev_lock);
+	mutex_destroy(&opp_table->lock);
 err:
 	kfree(opp_table);
 	return ERR_PTR(ret);
@@ -2388,8 +2391,8 @@
 		}
 
 		virt_dev = dev_pm_domain_attach_by_name(dev, *name);
-		if (IS_ERR(virt_dev)) {
-			ret = PTR_ERR(virt_dev);
+		if (IS_ERR_OR_NULL(virt_dev)) {
+			ret = virt_dev ? PTR_ERR(virt_dev) : -ENODEV;
 			dev_err(dev, "Couldn't attach to pm_domain: %d\n", ret);
 			goto err;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/opp/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/opp/debugfs.c
@@ -10,6 +10,7 @@
 #include <linux/debugfs.h>
 #include <linux/device.h>
 #include <linux/err.h>
+#include <linux/of.h>
 #include <linux/init.h>
 #include <linux/limits.h>
 #include <linux/slab.h>
@@ -36,10 +37,12 @@
 			    size_t count, loff_t *ppos)
 {
 	struct icc_path *path = fp->private_data;
+	const char *name = icc_get_name(path);
 	char buf[64];
-	int i;
+	int i = 0;
 
-	i = scnprintf(buf, sizeof(buf), "%.62s\n", icc_get_name(path));
+	if (name)
+		i = scnprintf(buf, sizeof(buf), "%.62s\n", name);
 
 	return simple_read_from_buffer(userbuf, count, ppos, buf, i);
 }
@@ -131,9 +134,13 @@
 	debugfs_create_bool("suspend", S_IRUGO, d, &opp->suspend);
 	debugfs_create_u32("performance_state", S_IRUGO, d, &opp->pstate);
 	debugfs_create_ulong("rate_hz", S_IRUGO, d, &opp->rate);
+	debugfs_create_u32("level", S_IRUGO, d, &opp->level);
 	debugfs_create_ulong("clock_latency_ns", S_IRUGO, d,
 			     &opp->clock_latency_ns);
 
+	opp->of_name = of_node_full_name(opp->np);
+	debugfs_create_str("of_name", S_IRUGO, d, (char **)&opp->of_name);
+
 	opp_debug_create_supplies(opp, opp_table, d);
 	opp_debug_create_bw(opp, opp_table, d);
 
@@ -204,7 +211,7 @@
 
 	dentry = debugfs_rename(rootdir, opp_dev->dentry, rootdir,
 				opp_table->dentry_name);
-	if (!dentry) {
+	if (IS_ERR(dentry)) {
 		dev_err(dev, "%s: Failed to rename link from: %s to %s\n",
 			__func__, dev_name(opp_dev->dev), dev_name(dev));
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/opp/of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/opp/of.c
@@ -437,11 +437,11 @@
 
 	/* Checking only first OPP is sufficient */
 	np = of_get_next_available_child(opp_np, NULL);
+	of_node_put(opp_np);
 	if (!np) {
 		dev_err(dev, "OPP table empty\n");
 		return -EINVAL;
 	}
-	of_node_put(opp_np);
 
 	prop = of_find_property(np, "opp-peak-kBps", NULL);
 	of_node_put(np);
@@ -921,7 +921,7 @@
 free_opp:
 	_opp_free(new_opp);
 
-	return ERR_PTR(ret);
+	return ret ? ERR_PTR(ret) : NULL;
 }
 
 /* Initializes OPP tables based on new bindings */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/opp/opp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/opp/opp.h
@@ -96,6 +96,7 @@
 
 #ifdef CONFIG_DEBUG_FS
 	struct dentry *dentry;
+	const char *of_name;
 #endif
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/ccio-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/ccio-dma.c
@@ -1003,7 +1003,7 @@
 	ioc->usg_calls++;
 #endif
 
-	while(sg_dma_len(sglist) && nents--) {
+	while (nents && sg_dma_len(sglist)) {
 
 #ifdef CCIO_COLLECT_STATS
 		ioc->usg_pages += sg_dma_len(sglist) >> PAGE_SHIFT;
@@ -1011,6 +1011,7 @@
 		ccio_unmap_page(dev, sg_dma_address(sglist),
 				  sg_dma_len(sglist), direction, 0);
 		++sglist;
+		nents--;
 	}
 
 	DBG_RUN_SG("%s() DONE (nents %d)\n", __func__, nents);
@@ -1379,15 +1380,17 @@
 	}
 }
 
-static void __init ccio_init_resources(struct ioc *ioc)
+static int __init ccio_init_resources(struct ioc *ioc)
 {
 	struct resource *res = ioc->mmio_region;
 	char *name = kmalloc(14, GFP_KERNEL);
-
+	if (unlikely(!name))
+		return -ENOMEM;
 	snprintf(name, 14, "GSC Bus [%d/]", ioc->hw_path);
 
 	ccio_init_resource(res, name, &ioc->ioc_regs->io_io_low);
 	ccio_init_resource(res + 1, name, &ioc->ioc_regs->io_io_low_hv);
+	return 0;
 }
 
 static int new_ioc_area(struct resource *res, unsigned long size,
@@ -1542,7 +1545,11 @@
 		return -ENOMEM;
 	}
 	ccio_ioc_init(ioc);
-	ccio_init_resources(ioc);
+	if (ccio_init_resources(ioc)) {
+		iounmap(ioc->ioc_regs);
+		kfree(ioc);
+		return -ENOMEM;
+	}
 	hppa_dma_ops = &ccio_ops;
 
 	hba = kzalloc(sizeof(*hba), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/dino.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/dino.c
@@ -142,9 +142,8 @@
 {
 	struct pci_hba_data	hba;	/* 'C' inheritance - must be first */
 	spinlock_t		dinosaur_pen;
-	unsigned long		txn_addr; /* EIR addr to generate interrupt */ 
-	u32			txn_data; /* EIR data assign to each dino */ 
 	u32 			imr;	  /* IRQ's which are enabled */ 
+	struct gsc_irq		gsc_irq;
 	int			global_irq[DINO_LOCAL_IRQS]; /* map IMR bit to global irq */
 #ifdef DINO_DEBUG
 	unsigned int		dino_irr0; /* save most recent IRQ line stat */
@@ -339,14 +338,43 @@
 	if (tmp & DINO_MASK_IRQ(local_irq)) {
 		DBG(KERN_WARNING "%s(): IRQ asserted! (ILR 0x%x)\n",
 				__func__, tmp);
-		gsc_writel(dino_dev->txn_data, dino_dev->txn_addr);
+		gsc_writel(dino_dev->gsc_irq.txn_data, dino_dev->gsc_irq.txn_addr);
 	}
 }
 
+#ifdef CONFIG_SMP
+static int dino_set_affinity_irq(struct irq_data *d, const struct cpumask *dest,
+				bool force)
+{
+	struct dino_device *dino_dev = irq_data_get_irq_chip_data(d);
+	struct cpumask tmask;
+	int cpu_irq;
+	u32 eim;
+
+	if (!cpumask_and(&tmask, dest, cpu_online_mask))
+		return -EINVAL;
+
+	cpu_irq = cpu_check_affinity(d, &tmask);
+	if (cpu_irq < 0)
+		return cpu_irq;
+
+	dino_dev->gsc_irq.txn_addr = txn_affinity_addr(d->irq, cpu_irq);
+	eim = ((u32) dino_dev->gsc_irq.txn_addr) | dino_dev->gsc_irq.txn_data;
+	__raw_writel(eim, dino_dev->hba.base_addr+DINO_IAR0);
+
+	irq_data_update_effective_affinity(d, &tmask);
+
+	return IRQ_SET_MASK_OK;
+}
+#endif
+
 static struct irq_chip dino_interrupt_type = {
 	.name		= "GSC-PCI",
 	.irq_unmask	= dino_unmask_irq,
 	.irq_mask	= dino_mask_irq,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = dino_set_affinity_irq,
+#endif
 };
 
 
@@ -806,7 +834,6 @@
 {
 	int status;
 	u32 eim;
-	struct gsc_irq gsc_irq;
 	struct resource *res;
 
 	pcibios_register_hba(&dino_dev->hba);
@@ -821,10 +848,8 @@
 	**   still only has 11 IRQ input lines - just map some of them
 	**   to a different processor.
 	*/
-	dev->irq = gsc_alloc_irq(&gsc_irq);
-	dino_dev->txn_addr = gsc_irq.txn_addr;
-	dino_dev->txn_data = gsc_irq.txn_data;
-	eim = ((u32) gsc_irq.txn_addr) | gsc_irq.txn_data;
+	dev->irq = gsc_alloc_irq(&dino_dev->gsc_irq);
+	eim = ((u32) dino_dev->gsc_irq.txn_addr) | dino_dev->gsc_irq.txn_data;
 
 	/* 
 	** Dino needs a PA "IRQ" to get a processor's attention.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/gsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/gsc.c
@@ -135,10 +135,41 @@
 	 */
 }
 
+#ifdef CONFIG_SMP
+static int gsc_set_affinity_irq(struct irq_data *d, const struct cpumask *dest,
+				bool force)
+{
+	struct gsc_asic *gsc_dev = irq_data_get_irq_chip_data(d);
+	struct cpumask tmask;
+	int cpu_irq;
+
+	if (!cpumask_and(&tmask, dest, cpu_online_mask))
+		return -EINVAL;
+
+	cpu_irq = cpu_check_affinity(d, &tmask);
+	if (cpu_irq < 0)
+		return cpu_irq;
+
+	gsc_dev->gsc_irq.txn_addr = txn_affinity_addr(d->irq, cpu_irq);
+	gsc_dev->eim = ((u32) gsc_dev->gsc_irq.txn_addr) | gsc_dev->gsc_irq.txn_data;
+
+	/* switch IRQ's for devices below LASI/WAX to other CPU */
+	gsc_writel(gsc_dev->eim, gsc_dev->hpa + OFFSET_IAR);
+
+	irq_data_update_effective_affinity(d, &tmask);
+
+	return IRQ_SET_MASK_OK;
+}
+#endif
+
+
 static struct irq_chip gsc_asic_interrupt_type = {
 	.name		=	"GSC-ASIC",
 	.irq_unmask	=	gsc_asic_unmask_irq,
 	.irq_mask	=	gsc_asic_mask_irq,
+#ifdef CONFIG_SMP
+	.irq_set_affinity =	gsc_set_affinity_irq,
+#endif
 };
 
 int gsc_assign_irq(struct irq_chip *type, void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/gsc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/gsc.h
@@ -31,6 +31,7 @@
 	int version;
 	int type;
 	int eim;
+	struct gsc_irq gsc_irq;
 	int global_irq[32];
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/iosapic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/iosapic.c
@@ -202,9 +202,9 @@
 
 static DEFINE_SPINLOCK(iosapic_lock);
 
-static inline void iosapic_eoi(void __iomem *addr, unsigned int data)
+static inline void iosapic_eoi(__le32 __iomem *addr, __le32 data)
 {
-	__raw_writel(data, addr);
+	__raw_writel((__force u32)data, addr);
 }
 
 /*
@@ -677,7 +677,7 @@
 	if (dest_cpu < 0)
 		return -1;
 
-	cpumask_copy(irq_data_get_affinity_mask(d), cpumask_of(dest_cpu));
+	irq_data_update_affinity(d, cpumask_of(dest_cpu));
 	vi->txn_addr = txn_affinity_addr(d->irq, dest_cpu);
 
 	spin_lock_irqsave(&iosapic_lock, flags);
@@ -875,6 +875,7 @@
 
 	return vi->txn_irq;
 }
+EXPORT_SYMBOL(iosapic_serial_irq);
 #endif
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/iosapic_private.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/iosapic_private.h
@@ -118,8 +118,8 @@
 struct vector_info {
 	struct iosapic_info *iosapic;	/* I/O SAPIC this vector is on */
 	struct irt_entry *irte;		/* IRT entry */
-	u32 __iomem *eoi_addr;		/* precalculate EOI reg address */
-	u32	eoi_data;		/* IA64: ?       PA: swapped txn_data */
+	__le32 __iomem *eoi_addr;	/* precalculate EOI reg address */
+	__le32	eoi_data;		/* IA64: ?       PA: swapped txn_data */
 	int	txn_irq;		/* virtual IRQ number for processor */
 	ulong	txn_addr;		/* IA64: id_eid  PA: partial HPA */
 	u32	txn_data;		/* CPU interrupt bit */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/lasi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/lasi.c
@@ -163,7 +163,6 @@
 {
 	extern void (*chassis_power_off)(void);
 	struct gsc_asic *lasi;
-	struct gsc_irq gsc_irq;
 	int ret;
 
 	lasi = kzalloc(sizeof(*lasi), GFP_KERNEL);
@@ -185,7 +184,7 @@
 	lasi_init_irq(lasi);
 
 	/* the IRQ lasi should use */
-	dev->irq = gsc_alloc_irq(&gsc_irq);
+	dev->irq = gsc_alloc_irq(&lasi->gsc_irq);
 	if (dev->irq < 0) {
 		printk(KERN_ERR "%s(): cannot get GSC irq\n",
 				__func__);
@@ -193,9 +192,9 @@
 		return -EBUSY;
 	}
 
-	lasi->eim = ((u32) gsc_irq.txn_addr) | gsc_irq.txn_data;
+	lasi->eim = ((u32) lasi->gsc_irq.txn_addr) | lasi->gsc_irq.txn_data;
 
-	ret = request_irq(gsc_irq.irq, gsc_asic_intr, 0, "lasi", lasi);
+	ret = request_irq(lasi->gsc_irq.irq, gsc_asic_intr, 0, "lasi", lasi);
 	if (ret < 0) {
 		kfree(lasi);
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/lba_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/lba_pci.c
@@ -1476,9 +1476,13 @@
 	u32 func_class;
 	void *tmp_obj;
 	char *version;
-	void __iomem *addr = ioremap(dev->hpa.start, 4096);
+	void __iomem *addr;
 	int max;
 
+	addr = ioremap(dev->hpa.start, 4096);
+	if (addr == NULL)
+		return -ENOMEM;
+
 	/* Read HW Rev First */
 	func_class = READ_REG32(addr + LBA_FCLASS);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/led.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/led.c
@@ -56,8 +56,8 @@
 static int led_type __read_mostly = -1;
 static unsigned char lastleds;	/* LED state from most recent update */
 static unsigned int led_heartbeat __read_mostly = 1;
-static unsigned int led_diskio    __read_mostly = 1;
-static unsigned int led_lanrxtx   __read_mostly = 1;
+static unsigned int led_diskio    __read_mostly;
+static unsigned int led_lanrxtx   __read_mostly;
 static char lcd_text[32]          __read_mostly;
 static char lcd_text_default[32]  __read_mostly;
 static int  lcd_no_led_support    __read_mostly = 0; /* KittyHawk doesn't support LED on its LCD */
@@ -137,6 +137,9 @@
 
 	/* Create the work queue and queue the LED task */
 	led_wq = create_singlethread_workqueue("led_wq");	
+	if (!led_wq)
+		return -ENOMEM;
+
 	queue_delayed_work(led_wq, &led_task, 0);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/pdc_stable.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/pdc_stable.c
@@ -979,8 +979,10 @@
 		entry->kobj.kset = paths_kset;
 		err = kobject_init_and_add(&entry->kobj, &ktype_pdcspath, NULL,
 					   "%s", entry->name);
-		if (err)
+		if (err) {
+			kobject_put(&entry->kobj);
 			return err;
+		}
 
 		/* kobject is now registered */
 		write_lock(&entry->rw_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/power.c
@@ -37,7 +37,6 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
-#include <linux/notifier.h>
 #include <linux/panic_notifier.h>
 #include <linux/reboot.h>
 #include <linux/sched/signal.h>
@@ -175,16 +174,21 @@
 
 
 
-/* parisc_panic_event() is called by the panic handler.
- * As soon as a panic occurs, our tasklets above will not be
- * executed any longer. This function then re-enables the 
- * soft-power switch and allows the user to switch off the system
+/*
+ * parisc_panic_event() is called by the panic handler.
+ *
+ * As soon as a panic occurs, our tasklets above will not
+ * be executed any longer. This function then re-enables
+ * the soft-power switch and allows the user to switch off
+ * the system. We rely in pdc_soft_power_button_panic()
+ * since this version spin_trylocks (instead of regular
+ * spinlock), preventing deadlocks on panic path.
  */
 static int parisc_panic_event(struct notifier_block *this,
 		unsigned long event, void *ptr)
 {
 	/* re-enable the soft-power switch */
-	pdc_soft_power_button(0);
+	pdc_soft_power_button_panic(0);
 	return NOTIFY_DONE;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/sba_iommu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/sba_iommu.c
@@ -1047,7 +1047,7 @@
 	spin_unlock_irqrestore(&ioc->res_lock, flags);
 #endif
 
-	while (sg_dma_len(sglist) && nents--) {
+	while (nents && sg_dma_len(sglist)) {
 
 		sba_unmap_page(dev, sg_dma_address(sglist), sg_dma_len(sglist),
 				direction, 0);
@@ -1056,6 +1056,7 @@
 		ioc->usingle_calls--;	/* kluge since call is unmap_sg() */
 #endif
 		++sglist;
+		nents--;
 	}
 
 	DBG_RUN_SG("%s() DONE (nents %d)\n", __func__,  nents);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parisc/wax.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parisc/wax.c
@@ -68,7 +68,6 @@
 {
 	struct gsc_asic *wax;
 	struct parisc_device *parent;
-	struct gsc_irq gsc_irq;
 	int ret;
 
 	wax = kzalloc(sizeof(*wax), GFP_KERNEL);
@@ -85,7 +84,7 @@
 	wax_init_irq(wax);
 
 	/* the IRQ wax should use */
-	dev->irq = gsc_claim_irq(&gsc_irq, WAX_GSC_IRQ);
+	dev->irq = gsc_claim_irq(&wax->gsc_irq, WAX_GSC_IRQ);
 	if (dev->irq < 0) {
 		printk(KERN_ERR "%s(): cannot get GSC irq\n",
 				__func__);
@@ -93,9 +92,9 @@
 		return -EBUSY;
 	}
 
-	wax->eim = ((u32) gsc_irq.txn_addr) | gsc_irq.txn_data;
+	wax->eim = ((u32) wax->gsc_irq.txn_addr) | wax->gsc_irq.txn_data;
 
-	ret = request_irq(gsc_irq.irq, gsc_asic_intr, 0, "wax", wax);
+	ret = request_irq(wax->gsc_irq.irq, gsc_asic_intr, 0, "wax", wax);
 	if (ret < 0) {
 		kfree(wax);
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parport/parport_pc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parport/parport_pc.c
@@ -468,7 +468,7 @@
 	const unsigned char *bufp = buf;
 	size_t left = length;
 	unsigned long expire = jiffies + port->physport->cad->timeout;
-	const int fifo = FIFO(port);
+	const unsigned long fifo = FIFO(port);
 	int poll_for = 8; /* 80 usecs */
 	const struct parport_pc_private *priv = port->physport->private_data;
 	const int fifo_depth = priv->fifo_depth;
@@ -2611,8 +2611,11 @@
 	netmos_9815,
 	netmos_9901,
 	netmos_9865,
+	asix_ax99100,
 	quatech_sppxp100,
 	wch_ch382l,
+	brainboxes_uc146,
+	brainboxes_px203,
 };
 
 
@@ -2674,8 +2677,11 @@
 	/* netmos_9815 */		{ 2, { { 0, 1 }, { 2, 3 }, } },
 	/* netmos_9901 */               { 1, { { 0, -1 }, } },
 	/* netmos_9865 */               { 1, { { 0, -1 }, } },
+	/* asix_ax99100 */		{ 1, { { 0, 1 }, } },
 	/* quatech_sppxp100 */		{ 1, { { 0, 1 }, } },
 	/* wch_ch382l */		{ 1, { { 2, -1 }, } },
+	/* brainboxes_uc146 */	{ 1, { { 3, -1 }, } },
+	/* brainboxes_px203 */	{ 1, { { 0, -1 }, } },
 };
 
 static const struct pci_device_id parport_pc_pci_tbl[] = {
@@ -2762,11 +2768,31 @@
 	  0xA000, 0x1000, 0, 0, netmos_9865 },
 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
 	  0xA000, 0x2000, 0, 0, netmos_9865 },
+	/* ASIX AX99100 PCIe to Multi I/O Controller */
+	{ PCI_VENDOR_ID_ASIX, PCI_DEVICE_ID_ASIX_AX99100,
+	  0xA000, 0x2000, 0, 0, asix_ax99100 },
 	/* Quatech SPPXP-100 Parallel port PCI ExpressCard */
 	{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SPPXP_100,
 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, quatech_sppxp100 },
 	/* WCH CH382L PCI-E single parallel port card */
 	{ 0x1c00, 0x3050, 0x1c00, 0x3050, 0, 0, wch_ch382l },
+	/* Brainboxes IX-500/550 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x402a,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
+	/* Brainboxes UC-146/UC-157 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0be1,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc146 },
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0be2,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc146 },
+	/* Brainboxes PX-146/PX-257 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x401c,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
+	/* Brainboxes PX-203 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x4007,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_px203 },
+	/* Brainboxes PX-475 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x401f,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
 	{ 0, } /* terminate list */
 };
 MODULE_DEVICE_TABLE(pci, parport_pc_pci_tbl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parport/parport_serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parport/parport_serial.c
@@ -65,6 +65,10 @@
 	sunix_5069a,
 	sunix_5079a,
 	sunix_5099a,
+	brainboxes_uc257,
+	brainboxes_is300,
+	brainboxes_uc414,
+	brainboxes_px263,
 };
 
 /* each element directly indexed from enum list, above */
@@ -158,6 +162,10 @@
 	/* sunix_5069a */		{ 1, { { 1, 2 }, } },
 	/* sunix_5079a */		{ 1, { { 1, 2 }, } },
 	/* sunix_5099a */		{ 1, { { 1, 2 }, } },
+	/* brainboxes_uc257 */	{ 1, { { 3, -1 }, } },
+	/* brainboxes_is300 */	{ 1, { { 3, -1 }, } },
+	/* brainboxes_uc414 */  { 1, { { 3, -1 }, } },
+	/* brainboxes_px263 */	{ 1, { { 3, -1 }, } },
 };
 
 static struct pci_device_id parport_serial_pci_tbl[] = {
@@ -277,6 +285,38 @@
 	{ PCI_VENDOR_ID_SUNIX, PCI_DEVICE_ID_SUNIX_1999, PCI_VENDOR_ID_SUNIX,
 	  0x0104, 0, 0, sunix_5099a },
 
+	/* Brainboxes UC-203 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0bc1,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0bc2,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+
+	/* Brainboxes UC-257 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0861,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0862,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0863,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+
+	/* Brainboxes UC-414 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0e61,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc414 },
+
+	/* Brainboxes UC-475 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0981,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0982,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_uc257 },
+
+	/* Brainboxes IS-300/IS-500 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x0da0,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_is300 },
+
+	/* Brainboxes PX-263/PX-295 */
+	{ PCI_VENDOR_ID_INTASHIELD, 0x402c,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, brainboxes_px263 },
+
 	{ 0, } /* terminate list */
 };
 MODULE_DEVICE_TABLE(pci,parport_serial_pci_tbl);
@@ -542,6 +582,30 @@
 		.base_baud      = 921600,
 		.uart_offset	= 0x8,
 	},
+	[brainboxes_uc257] = {
+		.flags		= FL_BASE2,
+		.num_ports	= 2,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+	},
+	[brainboxes_is300] = {
+		.flags		= FL_BASE2,
+		.num_ports	= 1,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+	},
+	[brainboxes_uc414] = {
+		.flags		= FL_BASE2,
+		.num_ports	= 4,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+	},
+	[brainboxes_px263] = {
+		.flags		= FL_BASE2,
+		.num_ports	= 4,
+		.base_baud	= 921600,
+		.uart_offset	= 8,
+	},
 };
 
 struct parport_serial_private {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/parport/procfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/parport/procfs.c
@@ -51,12 +51,12 @@
 	
 	for (dev = port->devices; dev ; dev = dev->next) {
 		if(dev == port->cad) {
-			len += sprintf(buffer, "%s\n", dev->name);
+			len += scnprintf(buffer, sizeof(buffer), "%s\n", dev->name);
 		}
 	}
 
 	if(!len) {
-		len += sprintf(buffer, "%s\n", "none");
+		len += scnprintf(buffer, sizeof(buffer), "%s\n", "none");
 	}
 
 	if (len > *lenp)
@@ -87,19 +87,19 @@
 	}
 	
 	if ((str = info->class_name) != NULL)
-		len += sprintf (buffer + len, "CLASS:%s;\n", str);
+		len += scnprintf (buffer + len, sizeof(buffer) - len, "CLASS:%s;\n", str);
 
 	if ((str = info->model) != NULL)
-		len += sprintf (buffer + len, "MODEL:%s;\n", str);
+		len += scnprintf (buffer + len, sizeof(buffer) - len, "MODEL:%s;\n", str);
 
 	if ((str = info->mfr) != NULL)
-		len += sprintf (buffer + len, "MANUFACTURER:%s;\n", str);
+		len += scnprintf (buffer + len, sizeof(buffer) - len, "MANUFACTURER:%s;\n", str);
 
 	if ((str = info->description) != NULL)
-		len += sprintf (buffer + len, "DESCRIPTION:%s;\n", str);
+		len += scnprintf (buffer + len, sizeof(buffer) - len, "DESCRIPTION:%s;\n", str);
 
 	if ((str = info->cmdset) != NULL)
-		len += sprintf (buffer + len, "COMMAND SET:%s;\n", str);
+		len += scnprintf (buffer + len, sizeof(buffer) - len, "COMMAND SET:%s;\n", str);
 
 	if (len > *lenp)
 		len = *lenp;
@@ -117,7 +117,7 @@
 				 void *result, size_t *lenp, loff_t *ppos)
 {
 	struct parport *port = (struct parport *)table->extra1;
-	char buffer[20];
+	char buffer[64];
 	int len = 0;
 
 	if (*ppos) {
@@ -128,7 +128,7 @@
 	if (write) /* permissions prevent this anyway */
 		return -EACCES;
 
-	len += sprintf (buffer, "%lu\t%lu\n", port->base, port->base_hi);
+	len += scnprintf (buffer, sizeof(buffer), "%lu\t%lu\n", port->base, port->base_hi);
 
 	if (len > *lenp)
 		len = *lenp;
@@ -155,7 +155,7 @@
 	if (write) /* permissions prevent this anyway */
 		return -EACCES;
 
-	len += sprintf (buffer, "%d\n", port->irq);
+	len += scnprintf (buffer, sizeof(buffer), "%d\n", port->irq);
 
 	if (len > *lenp)
 		len = *lenp;
@@ -182,7 +182,7 @@
 	if (write) /* permissions prevent this anyway */
 		return -EACCES;
 
-	len += sprintf (buffer, "%d\n", port->dma);
+	len += scnprintf (buffer, sizeof(buffer), "%d\n", port->dma);
 
 	if (len > *lenp)
 		len = *lenp;
@@ -213,7 +213,7 @@
 #define printmode(x)							\
 do {									\
 	if (port->modes & PARPORT_MODE_##x)				\
-		len += sprintf(buffer + len, "%s%s", f++ ? "," : "", #x); \
+		len += scnprintf(buffer + len, sizeof(buffer) - len, "%s%s", f++ ? "," : "", #x); \
 } while (0)
 		int f = 0;
 		printmode(PCSPP);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/access.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/access.c
@@ -160,9 +160,12 @@
 	 * write happen to have any RW1C (write-one-to-clear) bits set, we
 	 * just inadvertently cleared something we shouldn't have.
 	 */
-	dev_warn_ratelimited(&bus->dev, "%d-byte config write to %04x:%02x:%02x.%d offset %#x may corrupt adjacent RW1C bits\n",
-			     size, pci_domain_nr(bus), bus->number,
-			     PCI_SLOT(devfn), PCI_FUNC(devfn), where);
+	if (!bus->unsafe_warn) {
+		dev_warn(&bus->dev, "%d-byte config write to %04x:%02x:%02x.%d offset %#x may corrupt adjacent RW1C bits\n",
+			 size, pci_domain_nr(bus), bus->number,
+			 PCI_SLOT(devfn), PCI_FUNC(devfn), where);
+		bus->unsafe_warn = 1;
+	}
 
 	mask = ~(((1 << (size * 8)) - 1) << ((where & 0x3) * 8));
 	tmp = readl(addr) & mask;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/bus.c
@@ -76,6 +76,27 @@
 }
 EXPORT_SYMBOL_GPL(pci_bus_resource_n);
 
+void pci_bus_remove_resource(struct pci_bus *bus, struct resource *res)
+{
+	struct pci_bus_resource *bus_res, *tmp;
+	int i;
+
+	for (i = 0; i < PCI_BRIDGE_RESOURCE_NUM; i++) {
+		if (bus->resource[i] == res) {
+			bus->resource[i] = NULL;
+			return;
+		}
+	}
+
+	list_for_each_entry_safe(bus_res, tmp, &bus->resources, list) {
+		if (bus_res->res == res) {
+			list_del(&bus_res->list);
+			kfree(bus_res);
+			return;
+		}
+	}
+}
+
 void pci_bus_remove_resources(struct pci_bus *bus)
 {
 	int i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/Kconfig
@@ -108,6 +108,14 @@
 	  Say 'Y' here if you want kernel support for the
 	  Xilinx Versal CPM host bridge.
 
+config PCIE_XDMA_PL
+	bool "Xilinx XDMA PL PCIe host bridge support"
+	depends on ARCH_ZYNQMP || MICROBLAZE
+	depends on PCI_MSI_IRQ_DOMAIN
+	help
+	  Say 'Y' here if you want kernel to enable support the
+	  Xilinx XDMA PL PCIe Host Bridge driver.
+
 config PCI_XGENE
 	bool "X-Gene PCIe controller"
 	depends on ARM64 || COMPILE_TEST
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/Makefile
@@ -12,6 +12,7 @@
 obj-$(CONFIG_PCIE_RCAR_EP) += pcie-rcar.o pcie-rcar-ep.o
 obj-$(CONFIG_PCI_HOST_COMMON) += pci-host-common.o
 obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
+obj-$(CONFIG_PCIE_XDMA_PL) += pcie-xdma-pl.o
 obj-$(CONFIG_PCI_HOST_THUNDER_ECAM) += pci-thunder-ecam.o
 obj-$(CONFIG_PCI_HOST_THUNDER_PEM) += pci-thunder-pem.o
 obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/cadence/pci-j721e.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/cadence/pci-j721e.c
@@ -474,7 +474,7 @@
 		ret = clk_prepare_enable(clk);
 		if (ret) {
 			dev_err(dev, "failed to enable pcie_refclk\n");
-			goto err_get_sync;
+			goto err_pcie_setup;
 		}
 		pcie->refclk = clk;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/cadence/pcie-cadence-ep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/cadence/pcie-cadence-ep.c
@@ -187,8 +187,7 @@
 	struct cdns_pcie *pcie = &ep->pcie;
 	u32 r;
 
-	r = find_first_zero_bit(&ep->ob_region_map,
-				sizeof(ep->ob_region_map) * BITS_PER_LONG);
+	r = find_first_zero_bit(&ep->ob_region_map, BITS_PER_LONG);
 	if (r >= ep->max_regions - 1) {
 		dev_err(&epc->dev, "no free outbound region\n");
 		return -EINVAL;
@@ -355,8 +354,7 @@
 	spin_unlock_irqrestore(&ep->lock, flags);
 
 	offset = CDNS_PCIE_NORMAL_MSG_ROUTING(MSG_ROUTING_LOCAL) |
-		 CDNS_PCIE_NORMAL_MSG_CODE(msg_code) |
-		 CDNS_PCIE_MSG_NO_DATA;
+		 CDNS_PCIE_NORMAL_MSG_CODE(msg_code);
 	writel(0, ep->irq_cpu_addr + offset);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/cadence/pcie-cadence-host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/cadence/pcie-cadence-host.c
@@ -12,6 +12,8 @@
 
 #include "pcie-cadence.h"
 
+#define LINK_RETRAIN_TIMEOUT HZ
+
 static u64 bar_max_size[] = {
 	[RP_BAR0] = _ULL(128 * SZ_2G),
 	[RP_BAR1] = SZ_2G,
@@ -77,6 +79,27 @@
 	.write		= pci_generic_config_write,
 };
 
+static int cdns_pcie_host_training_complete(struct cdns_pcie *pcie)
+{
+	u32 pcie_cap_off = CDNS_PCIE_RP_CAP_OFFSET;
+	unsigned long end_jiffies;
+	u16 lnk_stat;
+
+	/* Wait for link training to complete. Exit after timeout. */
+	end_jiffies = jiffies + LINK_RETRAIN_TIMEOUT;
+	do {
+		lnk_stat = cdns_pcie_rp_readw(pcie, pcie_cap_off + PCI_EXP_LNKSTA);
+		if (!(lnk_stat & PCI_EXP_LNKSTA_LT))
+			break;
+		usleep_range(0, 1000);
+	} while (time_before(jiffies, end_jiffies));
+
+	if (!(lnk_stat & PCI_EXP_LNKSTA_LT))
+		return 0;
+
+	return -ETIMEDOUT;
+}
+
 static int cdns_pcie_host_wait_for_link(struct cdns_pcie *pcie)
 {
 	struct device *dev = pcie->dev;
@@ -118,6 +141,10 @@
 		cdns_pcie_rp_writew(pcie, pcie_cap_off + PCI_EXP_LNKCTL,
 				    lnk_ctl);
 
+		ret = cdns_pcie_host_training_complete(pcie);
+		if (ret)
+			return ret;
+
 		ret = cdns_pcie_host_wait_for_link(pcie);
 	}
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/cadence/pcie-cadence-plat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/cadence/pcie-cadence-plat.c
@@ -127,6 +127,8 @@
 			goto err_init;
 	}
 
+	return 0;
+
  err_init:
  err_get_sync:
 	pm_runtime_put_sync(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/cadence/pcie-cadence.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/cadence/pcie-cadence.h
@@ -235,7 +235,7 @@
 #define CDNS_PCIE_NORMAL_MSG_CODE_MASK		GENMASK(15, 8)
 #define CDNS_PCIE_NORMAL_MSG_CODE(code) \
 	(((code) << 8) & CDNS_PCIE_NORMAL_MSG_CODE_MASK)
-#define CDNS_PCIE_MSG_NO_DATA			BIT(16)
+#define CDNS_PCIE_MSG_DATA			BIT(16)
 
 struct cdns_pcie;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pci-exynos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pci-exynos.c
@@ -377,7 +377,7 @@
 	return ret;
 }
 
-static int __exit exynos_pcie_remove(struct platform_device *pdev)
+static int exynos_pcie_remove(struct platform_device *pdev)
 {
 	struct exynos_pcie *ep = platform_get_drvdata(pdev);
 
@@ -433,7 +433,7 @@
 
 static struct platform_driver exynos_pcie_driver = {
 	.probe		= exynos_pcie_probe,
-	.remove		= __exit_p(exynos_pcie_remove),
+	.remove		= exynos_pcie_remove,
 	.driver = {
 		.name	= "exynos-pcie",
 		.of_match_table = exynos_pcie_of_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pci-imx6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pci-imx6.c
@@ -403,6 +403,11 @@
 			dev_err(dev, "failed to disable vpcie regulator: %d\n",
 				ret);
 	}
+
+	/* Some boards don't have PCIe reset GPIO. */
+	if (gpio_is_valid(imx6_pcie->reset_gpio))
+		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
+					imx6_pcie->gpio_active_high);
 }
 
 static unsigned int imx6_pcie_grp_offset(const struct imx6_pcie *imx6_pcie)
@@ -525,15 +530,6 @@
 	/* allow the clocks to stabilize */
 	usleep_range(200, 500);
 
-	/* Some boards don't have PCIe reset GPIO. */
-	if (gpio_is_valid(imx6_pcie->reset_gpio)) {
-		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
-					imx6_pcie->gpio_active_high);
-		msleep(100);
-		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
-					!imx6_pcie->gpio_active_high);
-	}
-
 	switch (imx6_pcie->drvdata->variant) {
 	case IMX8MQ:
 		reset_control_deassert(imx6_pcie->pciephy_reset);
@@ -576,6 +572,15 @@
 		break;
 	}
 
+	/* Some boards don't have PCIe reset GPIO. */
+	if (gpio_is_valid(imx6_pcie->reset_gpio)) {
+		msleep(100);
+		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
+					!imx6_pcie->gpio_active_high);
+		/* Wait for 100ms after PERST# deassertion (PCIe r5.0, 6.6.1) */
+		msleep(100);
+	}
+
 	return;
 
 err_ref_clk:
@@ -779,9 +784,7 @@
 	/* Start LTSSM. */
 	imx6_pcie_ltssm_enable(dev);
 
-	ret = dw_pcie_wait_for_link(pci);
-	if (ret)
-		goto err_reset_phy;
+	dw_pcie_wait_for_link(pci);
 
 	if (pci->link_gen == 2) {
 		/* Allow Gen2 mode after the link is up. */
@@ -817,11 +820,7 @@
 		}
 
 		/* Make sure link training is finished as well! */
-		ret = dw_pcie_wait_for_link(pci);
-		if (ret) {
-			dev_err(dev, "Failed to bring link up!\n");
-			goto err_reset_phy;
-		}
+		dw_pcie_wait_for_link(pci);
 	} else {
 		dev_info(dev, "Link: Gen2 disabled\n");
 	}
@@ -1259,6 +1258,13 @@
 static int __init imx6_pcie_init(void)
 {
 #ifdef CONFIG_ARM
+	struct device_node *np;
+
+	np = of_find_matching_node(NULL, imx6_pcie_of_match);
+	if (!np)
+		return -ENODEV;
+	of_node_put(np);
+
 	/*
 	 * Since probe() can be deferred we need to make sure that
 	 * hook_fault_code is not called after __init memory is freed
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pci-keystone.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pci-keystone.c
@@ -35,6 +35,11 @@
 #define PCIE_DEVICEID_SHIFT	16
 
 /* Application registers */
+#define PID				0x000
+#define RTL				GENMASK(15, 11)
+#define RTL_SHIFT			11
+#define AM6_PCI_PG1_RTL_VER		0x15
+
 #define CMD_STATUS			0x004
 #define LTSSM_EN_VAL		        BIT(0)
 #define OB_XLAT_EN_VAL		        BIT(1)
@@ -105,6 +110,8 @@
 
 #define to_keystone_pcie(x)		dev_get_drvdata((x)->dev)
 
+#define PCI_DEVICE_ID_TI_AM654X		0xb00c
+
 struct ks_pcie_of_data {
 	enum dw_pcie_device_mode mode;
 	const struct dw_pcie_host_ops *host_ops;
@@ -433,6 +440,17 @@
 	struct keystone_pcie *ks_pcie = to_keystone_pcie(pci);
 	u32 reg;
 
+	/*
+	 * Checking whether the link is up here is a last line of defense
+	 * against platforms that forward errors on the system bus as
+	 * SError upon PCI configuration transactions issued when the link
+	 * is down. This check is racy by definition and does not stop
+	 * the system from triggering an SError if the link goes down
+	 * after this check is performed.
+	 */
+	if (!dw_pcie_link_up(pci))
+		return NULL;
+
 	reg = CFG_BUS(bus->number) | CFG_DEVICE(PCI_SLOT(devfn)) |
 		CFG_FUNC(PCI_FUNC(devfn));
 	if (!pci_is_root_bus(bus->parent))
@@ -528,7 +546,11 @@
 static void ks_pcie_quirk(struct pci_dev *dev)
 {
 	struct pci_bus *bus = dev->bus;
+	struct keystone_pcie *ks_pcie;
+	struct device *bridge_dev;
 	struct pci_dev *bridge;
+	u32 val;
+
 	static const struct pci_device_id rc_pci_devids[] = {
 		{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2HK),
 		 .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, },
@@ -540,6 +562,11 @@
 		 .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, },
 		{ 0, },
 	};
+	static const struct pci_device_id am6_pci_devids[] = {
+		{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_AM654X),
+		 .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, },
+		{ 0, },
+	};
 
 	if (pci_is_root_bus(bus))
 		bridge = dev;
@@ -561,10 +588,36 @@
 	 */
 	if (pci_match_id(rc_pci_devids, bridge)) {
 		if (pcie_get_readrq(dev) > 256) {
-			dev_info(&dev->dev, "limiting MRRS to 256\n");
+			dev_info(&dev->dev, "limiting MRRS to 256 bytes\n");
 			pcie_set_readrq(dev, 256);
 		}
 	}
+
+	/*
+	 * Memory transactions fail with PCI controller in AM654 PG1.0
+	 * when MRRS is set to more than 128 bytes. Force the MRRS to
+	 * 128 bytes in all downstream devices.
+	 */
+	if (pci_match_id(am6_pci_devids, bridge)) {
+		bridge_dev = pci_get_host_bridge_device(dev);
+		if (!bridge_dev || !bridge_dev->parent)
+			return;
+
+		ks_pcie = dev_get_drvdata(bridge_dev->parent);
+		if (!ks_pcie)
+			return;
+
+		val = ks_pcie_app_readl(ks_pcie, PID);
+		val &= RTL;
+		val >>= RTL_SHIFT;
+		if (val != AM6_PCI_PG1_RTL_VER)
+			return;
+
+		if (pcie_get_readrq(dev) > 128) {
+			dev_info(&dev->dev, "limiting MRRS to 128 bytes\n");
+			pcie_set_readrq(dev, 128);
+		}
+	}
 }
 DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, ks_pcie_quirk);
 
@@ -1080,7 +1133,7 @@
 	{ },
 };
 
-static int __init ks_pcie_probe(struct platform_device *pdev)
+static int ks_pcie_probe(struct platform_device *pdev)
 {
 	const struct dw_pcie_host_ops *host_ops;
 	const struct dw_pcie_ep_ops *ep_ops;
@@ -1200,7 +1253,16 @@
 		goto err_link;
 	}
 
+	/* Obtain references to the PHYs */
+	for (i = 0; i < num_lanes; i++)
+		phy_pm_runtime_get_sync(ks_pcie->phy[i]);
+
 	ret = ks_pcie_enable_phy(ks_pcie);
+
+	/* Release references to the PHYs */
+	for (i = 0; i < num_lanes; i++)
+		phy_pm_runtime_put_sync(ks_pcie->phy[i]);
+
 	if (ret) {
 		dev_err(dev, "failed to enable phy\n");
 		goto err_link;
@@ -1284,7 +1346,7 @@
 	return ret;
 }
 
-static int __exit ks_pcie_remove(struct platform_device *pdev)
+static int ks_pcie_remove(struct platform_device *pdev)
 {
 	struct keystone_pcie *ks_pcie = platform_get_drvdata(pdev);
 	struct device_link **link = ks_pcie->link;
@@ -1300,9 +1362,9 @@
 	return 0;
 }
 
-static struct platform_driver ks_pcie_driver __refdata = {
+static struct platform_driver ks_pcie_driver = {
 	.probe  = ks_pcie_probe,
-	.remove = __exit_p(ks_pcie_remove),
+	.remove = ks_pcie_remove,
 	.driver = {
 		.name	= "keystone-pcie",
 		.of_match_table = of_match_ptr(ks_pcie_of_match),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pci-layerscape-ep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pci-layerscape-ep.c
@@ -18,6 +18,20 @@
 
 #include "pcie-designware.h"
 
+#define PEX_PF0_CONFIG			0xC0014
+#define PEX_PF0_CFG_READY		BIT(0)
+
+/* PEX PFa PCIE PME and message interrupt registers*/
+#define PEX_PF0_PME_MES_DR		0xC0020
+#define PEX_PF0_PME_MES_DR_LUD		BIT(7)
+#define PEX_PF0_PME_MES_DR_LDD		BIT(9)
+#define PEX_PF0_PME_MES_DR_HRD		BIT(10)
+
+#define PEX_PF0_PME_MES_IER		0xC0028
+#define PEX_PF0_PME_MES_IER_LUDIE	BIT(7)
+#define PEX_PF0_PME_MES_IER_LDDIE	BIT(9)
+#define PEX_PF0_PME_MES_IER_HRDIE	BIT(10)
+
 #define to_ls_pcie_ep(x)	dev_get_drvdata((x)->dev)
 
 struct ls_pcie_ep_drvdata {
@@ -30,16 +44,98 @@
 	struct dw_pcie			*pci;
 	struct pci_epc_features		*ls_epc;
 	const struct ls_pcie_ep_drvdata *drvdata;
+	int				irq;
+	u32				lnkcap;
+	bool				big_endian;
 };
 
-static int ls_pcie_establish_link(struct dw_pcie *pci)
+static u32 ls_lut_readl(struct ls_pcie_ep *pcie, u32 offset)
 {
-	return 0;
+	struct dw_pcie *pci = pcie->pci;
+
+	if (pcie->big_endian)
+		return ioread32be(pci->dbi_base + offset);
+	else
+		return ioread32(pci->dbi_base + offset);
 }
 
-static const struct dw_pcie_ops dw_ls_pcie_ep_ops = {
-	.start_link = ls_pcie_establish_link,
-};
+static void ls_lut_writel(struct ls_pcie_ep *pcie, u32 offset, u32 value)
+{
+	struct dw_pcie *pci = pcie->pci;
+
+	if (pcie->big_endian)
+		iowrite32be(value, pci->dbi_base + offset);
+	else
+		iowrite32(value, pci->dbi_base + offset);
+}
+
+static irqreturn_t ls_pcie_ep_event_handler(int irq, void *dev_id)
+{
+	struct ls_pcie_ep *pcie = dev_id;
+	struct dw_pcie *pci = pcie->pci;
+	u32 val, cfg;
+	u8 offset;
+
+	val = ls_lut_readl(pcie, PEX_PF0_PME_MES_DR);
+	ls_lut_writel(pcie, PEX_PF0_PME_MES_DR, val);
+
+	if (!val)
+		return IRQ_NONE;
+
+	if (val & PEX_PF0_PME_MES_DR_LUD) {
+
+		offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+
+		/*
+		 * The values of the Maximum Link Width and Supported Link
+		 * Speed from the Link Capabilities Register will be lost
+		 * during link down or hot reset. Restore initial value
+		 * that configured by the Reset Configuration Word (RCW).
+		 */
+		dw_pcie_dbi_ro_wr_en(pci);
+		dw_pcie_writel_dbi(pci, offset + PCI_EXP_LNKCAP, pcie->lnkcap);
+		dw_pcie_dbi_ro_wr_dis(pci);
+
+		cfg = ls_lut_readl(pcie, PEX_PF0_CONFIG);
+		cfg |= PEX_PF0_CFG_READY;
+		ls_lut_writel(pcie, PEX_PF0_CONFIG, cfg);
+		dw_pcie_ep_linkup(&pci->ep);
+
+		dev_dbg(pci->dev, "Link up\n");
+	} else if (val & PEX_PF0_PME_MES_DR_LDD) {
+		dev_dbg(pci->dev, "Link down\n");
+	} else if (val & PEX_PF0_PME_MES_DR_HRD) {
+		dev_dbg(pci->dev, "Hot reset\n");
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int ls_pcie_ep_interrupt_init(struct ls_pcie_ep *pcie,
+				     struct platform_device *pdev)
+{
+	u32 val;
+	int ret;
+
+	pcie->irq = platform_get_irq_byname(pdev, "pme");
+	if (pcie->irq < 0)
+		return pcie->irq;
+
+	ret = devm_request_irq(&pdev->dev, pcie->irq, ls_pcie_ep_event_handler,
+			       IRQF_SHARED, pdev->name, pcie);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't register PCIe IRQ\n");
+		return ret;
+	}
+
+	/* Enable interrupts */
+	val = ls_lut_readl(pcie, PEX_PF0_PME_MES_IER);
+	val |=  PEX_PF0_PME_MES_IER_LDDIE | PEX_PF0_PME_MES_IER_HRDIE |
+		PEX_PF0_PME_MES_IER_LUDIE;
+	ls_lut_writel(pcie, PEX_PF0_PME_MES_IER, val);
+
+	return 0;
+}
 
 static const struct pci_epc_features*
 ls_pcie_ep_get_features(struct dw_pcie_ep *ep)
@@ -106,19 +202,16 @@
 
 static const struct ls_pcie_ep_drvdata ls1_ep_drvdata = {
 	.ops = &ls_pcie_ep_ops,
-	.dw_pcie_ops = &dw_ls_pcie_ep_ops,
 };
 
 static const struct ls_pcie_ep_drvdata ls2_ep_drvdata = {
 	.func_offset = 0x20000,
 	.ops = &ls_pcie_ep_ops,
-	.dw_pcie_ops = &dw_ls_pcie_ep_ops,
 };
 
 static const struct ls_pcie_ep_drvdata lx2_ep_drvdata = {
 	.func_offset = 0x8000,
 	.ops = &ls_pcie_ep_ops,
-	.dw_pcie_ops = &dw_ls_pcie_ep_ops,
 };
 
 static const struct of_device_id ls_pcie_ep_of_match[] = {
@@ -136,6 +229,8 @@
 	struct ls_pcie_ep *pcie;
 	struct pci_epc_features *ls_epc;
 	struct resource *dbi_base;
+	u8 offset;
+	int ret;
 
 	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
 	if (!pcie)
@@ -155,6 +250,7 @@
 	pci->ops = pcie->drvdata->dw_pcie_ops;
 
 	ls_epc->bar_fixed_64bit = (1 << BAR_2) | (1 << BAR_4);
+	ls_epc->linkup_notifier = true;
 
 	pcie->pci = pci;
 	pcie->ls_epc = ls_epc;
@@ -166,9 +262,18 @@
 
 	pci->ep.ops = &ls_pcie_ep_ops;
 
+	pcie->big_endian = of_property_read_bool(dev->of_node, "big-endian");
+
 	platform_set_drvdata(pdev, pcie);
 
-	return dw_pcie_ep_init(&pci->ep);
+	offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	pcie->lnkcap = dw_pcie_readl_dbi(pci, offset + PCI_EXP_LNKCAP);
+
+	ret = dw_pcie_ep_init(&pci->ep);
+	if (ret)
+		return ret;
+
+	return ls_pcie_ep_interrupt_init(pcie, pdev);
 }
 
 static struct platform_driver ls_pcie_ep_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-al.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-al.c
@@ -242,18 +242,24 @@
 	.write = pci_generic_config_write,
 };
 
-static void al_pcie_config_prepare(struct al_pcie *pcie)
+static int al_pcie_config_prepare(struct al_pcie *pcie)
 {
 	struct al_pcie_target_bus_cfg *target_bus_cfg;
 	struct pcie_port *pp = &pcie->pci->pp;
 	unsigned int ecam_bus_mask;
+	struct resource_entry *ft;
 	u32 cfg_control_offset;
+	struct resource *bus;
 	u8 subordinate_bus;
 	u8 secondary_bus;
 	u32 cfg_control;
 	u32 reg;
-	struct resource *bus = resource_list_first_type(&pp->bridge->windows, IORESOURCE_BUS)->res;
 
+	ft = resource_list_first_type(&pp->bridge->windows, IORESOURCE_BUS);
+	if (!ft)
+		return -ENODEV;
+
+	bus = ft->res;
 	target_bus_cfg = &pcie->target_bus_cfg;
 
 	ecam_bus_mask = (pcie->ecam_size >> PCIE_ECAM_BUS_SHIFT) - 1;
@@ -287,6 +293,8 @@
 	       FIELD_PREP(CFG_CONTROL_SEC_BUS_MASK, secondary_bus);
 
 	al_pcie_controller_writel(pcie, cfg_control_offset, reg);
+
+	return 0;
 }
 
 static int al_pcie_host_init(struct pcie_port *pp)
@@ -305,7 +313,9 @@
 	if (rc)
 		return rc;
 
-	al_pcie_config_prepare(pcie);
+	rc = al_pcie_config_prepare(pcie);
+	if (rc)
+		return rc;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-designware-ep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-designware-ep.c
@@ -6,6 +6,7 @@
  * Author: Kishon Vijay Abraham I <kishon@ti.com>
  */
 
+#include <linux/align.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
 
@@ -434,8 +435,7 @@
 	struct dw_pcie_ep *ep = epc_get_drvdata(epc);
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 
-	if (pci->ops && pci->ops->stop_link)
-		pci->ops->stop_link(pci);
+	dw_pcie_stop_link(pci);
 }
 
 static int dw_pcie_ep_start(struct pci_epc *epc)
@@ -443,10 +443,7 @@
 	struct dw_pcie_ep *ep = epc_get_drvdata(epc);
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
 
-	if (!pci->ops || !pci->ops->start_link)
-		return -EINVAL;
-
-	return pci->ops->start_link(pci);
+	return dw_pcie_start_link(pci);
 }
 
 static const struct pci_epc_features*
@@ -593,6 +590,7 @@
 	}
 
 	aligned_offset = msg_addr & (epc->mem->window.page_size - 1);
+	msg_addr = ALIGN_DOWN(msg_addr, epc->mem->window.page_size);
 	ret = dw_pcie_ep_map_addr(epc, func_no, 0, ep->msi_mem_phys, msg_addr,
 				  epc->mem->window.page_size);
 	if (ret)
@@ -660,8 +658,13 @@
 		nbars = (reg & PCI_REBAR_CTRL_NBAR_MASK) >>
 			PCI_REBAR_CTRL_NBAR_SHIFT;
 
+		/*
+		 * PCIe r6.0, sec 7.8.6.2 require us to support at least one
+		 * size in the range from 1 MB to 512 GB. Advertise support
+		 * for 1 MB BAR size only.
+		 */
 		for (i = 0; i < nbars; i++, offset += PCI_REBAR_CTRL)
-			dw_pcie_writel_dbi(pci, offset + PCI_REBAR_CAP, 0x0);
+			dw_pcie_writel_dbi(pci, offset + PCI_REBAR_CAP, BIT(4));
 	}
 
 	dw_pcie_setup(pci);
@@ -777,8 +780,9 @@
 	ep->msi_mem = pci_epc_mem_alloc_addr(epc, &ep->msi_mem_phys,
 					     epc->mem->window.page_size);
 	if (!ep->msi_mem) {
+		ret = -ENOMEM;
 		dev_err(dev, "Failed to reserve memory for MSI/MSI-X\n");
-		return -ENOMEM;
+		goto err_exit_epc_mem;
 	}
 
 	if (ep->ops->get_features) {
@@ -787,6 +791,19 @@
 			return 0;
 	}
 
-	return dw_pcie_ep_init_complete(ep);
+	ret = dw_pcie_ep_init_complete(ep);
+	if (ret)
+		goto err_free_epc_mem;
+
+	return 0;
+
+err_free_epc_mem:
+	pci_epc_mem_free_addr(epc, ep->msi_mem_phys, ep->msi_mem,
+			      epc->mem->window.page_size);
+
+err_exit_epc_mem:
+	pci_epc_mem_exit(epc);
+
+	return ret;
 }
 EXPORT_SYMBOL_GPL(dw_pcie_ep_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-designware-host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -352,6 +352,12 @@
 			if (ret < 0)
 				return ret;
 		} else if (pp->has_msi_ctrl) {
+			u32 ctrl, num_ctrls;
+
+			num_ctrls = pp->num_vectors / MAX_MSI_IRQS_PER_CTRL;
+			for (ctrl = 0; ctrl < num_ctrls; ctrl++)
+				pp->irq_mask[ctrl] = ~0;
+
 			if (!pp->msi_irq) {
 				pp->msi_irq = platform_get_irq_byname_optional(pdev, "msi");
 				if (pp->msi_irq < 0) {
@@ -380,7 +386,8 @@
 						      sizeof(pp->msi_msg),
 						      DMA_FROM_DEVICE,
 						      DMA_ATTR_SKIP_CPU_SYNC);
-			if (dma_mapping_error(pci->dev, pp->msi_data)) {
+			ret = dma_mapping_error(pci->dev, pp->msi_data);
+			if (ret) {
 				dev_err(pci->dev, "Failed to map MSI data\n");
 				pp->msi_data = 0;
 				goto err_free_msi;
@@ -401,8 +408,8 @@
 
 	dw_pcie_setup_rc(pp);
 
-	if (!dw_pcie_link_up(pci) && pci->ops && pci->ops->start_link) {
-		ret = pci->ops->start_link(pci);
+	if (!dw_pcie_link_up(pci)) {
+		ret = dw_pcie_start_link(pci);
 		if (ret)
 			goto err_free_msi;
 	}
@@ -413,8 +420,13 @@
 	bridge->sysdata = pp;
 
 	ret = pci_host_probe(bridge);
-	if (!ret)
-		return 0;
+	if (ret)
+		goto err_stop_link;
+
+	return 0;
+
+err_stop_link:
+	dw_pcie_stop_link(pci);
 
 err_free_msi:
 	if (pp->has_msi_ctrl)
@@ -425,8 +437,13 @@
 
 void dw_pcie_host_deinit(struct pcie_port *pp)
 {
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+
 	pci_stop_root_bus(pp->bridge->bus);
 	pci_remove_root_bus(pp->bridge->bus);
+
+	dw_pcie_stop_link(pci);
+
 	if (pp->has_msi_ctrl)
 		dw_pcie_free_msi(pp);
 }
@@ -523,7 +540,6 @@
 
 void dw_pcie_setup_rc(struct pcie_port *pp)
 {
-	int i;
 	u32 val, ctrl, num_ctrls;
 	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
 
@@ -540,7 +556,6 @@
 
 		/* Initialize IRQ Status array */
 		for (ctrl = 0; ctrl < num_ctrls; ctrl++) {
-			pp->irq_mask[ctrl] = ~0;
 			dw_pcie_writel_dbi(pci, PCIE_MSI_INTR0_MASK +
 					    (ctrl * MSI_REG_CTRL_BLOCK_SIZE),
 					    pp->irq_mask[ctrl]);
@@ -575,19 +590,22 @@
 		PCI_COMMAND_MASTER | PCI_COMMAND_SERR;
 	dw_pcie_writel_dbi(pci, PCI_COMMAND, val);
 
-	/* Ensure all outbound windows are disabled so there are multiple matches */
-	for (i = 0; i < pci->num_ob_windows; i++)
-		dw_pcie_disable_atu(pci, i, DW_PCIE_REGION_OUTBOUND);
-
 	/*
 	 * If the platform provides its own child bus config accesses, it means
 	 * the platform uses its own address translation component rather than
 	 * ATU, so we should not program the ATU here.
 	 */
 	if (pp->bridge->child_ops == &dw_child_pcie_ops) {
-		int atu_idx = 0;
+		int i, atu_idx = 0;
 		struct resource_entry *entry;
 
+		/*
+		 * Disable all outbound windows to make sure a transaction
+		 * can't match multiple windows.
+		 */
+		for (i = 0; i < pci->num_ob_windows; i++)
+			dw_pcie_disable_atu(pci, i, DW_PCIE_REGION_OUTBOUND);
+
 		/* Get last memory resource entry */
 		resource_list_for_each_entry(entry, &pp->bridge->windows) {
 			if (resource_type(entry->res) != IORESOURCE_MEM)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-designware-plat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-designware-plat.c
@@ -36,15 +36,6 @@
 static const struct dw_pcie_host_ops dw_plat_pcie_host_ops = {
 };
 
-static int dw_plat_pcie_establish_link(struct dw_pcie *pci)
-{
-	return 0;
-}
-
-static const struct dw_pcie_ops dw_pcie_ops = {
-	.start_link = dw_plat_pcie_establish_link,
-};
-
 static void dw_plat_pcie_ep_init(struct dw_pcie_ep *ep)
 {
 	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
@@ -142,7 +133,6 @@
 		return -ENOMEM;
 
 	pci->dev = dev;
-	pci->ops = &dw_pcie_ops;
 
 	dw_plat_pcie->pci = pci;
 	dw_plat_pcie->mode = mode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-designware.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-designware.c
@@ -287,8 +287,8 @@
 	dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_UPPER_TARGET,
 				 upper_32_bits(pci_addr));
 	val = type | PCIE_ATU_FUNC_NUM(func_no);
-	val = upper_32_bits(size - 1) ?
-		val | PCIE_ATU_INCREASE_REGION_SIZE : val;
+	if (upper_32_bits(limit_addr) > upper_32_bits(cpu_addr))
+		val |= PCIE_ATU_INCREASE_REGION_SIZE;
 	if (pci->version == 0x490A)
 		val = dw_pcie_enable_ecrc(val);
 	dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL1, val);
@@ -315,6 +315,7 @@
 					u64 pci_addr, u64 size)
 {
 	u32 retries, val;
+	u64 limit_addr;
 
 	if (pci->ops && pci->ops->cpu_addr_fixup)
 		cpu_addr = pci->ops->cpu_addr_fixup(pci, cpu_addr);
@@ -325,6 +326,8 @@
 		return;
 	}
 
+	limit_addr = cpu_addr + size - 1;
+
 	dw_pcie_writel_dbi(pci, PCIE_ATU_VIEWPORT,
 			   PCIE_ATU_REGION_OUTBOUND | index);
 	dw_pcie_writel_dbi(pci, PCIE_ATU_LOWER_BASE,
@@ -332,17 +335,18 @@
 	dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_BASE,
 			   upper_32_bits(cpu_addr));
 	dw_pcie_writel_dbi(pci, PCIE_ATU_LIMIT,
-			   lower_32_bits(cpu_addr + size - 1));
+			   lower_32_bits(limit_addr));
 	if (pci->version >= 0x460A)
 		dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_LIMIT,
-				   upper_32_bits(cpu_addr + size - 1));
+				   upper_32_bits(limit_addr));
 	dw_pcie_writel_dbi(pci, PCIE_ATU_LOWER_TARGET,
 			   lower_32_bits(pci_addr));
 	dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_TARGET,
 			   upper_32_bits(pci_addr));
 	val = type | PCIE_ATU_FUNC_NUM(func_no);
-	val = ((upper_32_bits(size - 1)) && (pci->version >= 0x460A)) ?
-		val | PCIE_ATU_INCREASE_REGION_SIZE : val;
+	if (upper_32_bits(limit_addr) > upper_32_bits(cpu_addr) &&
+	    pci->version >= 0x460A)
+		val |= PCIE_ATU_INCREASE_REGION_SIZE;
 	if (pci->version == 0x490A)
 		val = dw_pcie_enable_ecrc(val);
 	dw_pcie_writel_dbi(pci, PCIE_ATU_CR1, val);
@@ -491,7 +495,7 @@
 void dw_pcie_disable_atu(struct dw_pcie *pci, int index,
 			 enum dw_pcie_region_type type)
 {
-	int region;
+	u32 region;
 
 	switch (type) {
 	case DW_PCIE_REGION_INBOUND:
@@ -504,8 +508,18 @@
 		return;
 	}
 
-	dw_pcie_writel_dbi(pci, PCIE_ATU_VIEWPORT, region | index);
-	dw_pcie_writel_dbi(pci, PCIE_ATU_CR2, ~(u32)PCIE_ATU_ENABLE);
+	if (pci->iatu_unroll_enabled) {
+		if (region == PCIE_ATU_REGION_INBOUND) {
+			dw_pcie_writel_ib_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL2,
+						 ~(u32)PCIE_ATU_ENABLE);
+		} else {
+			dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL2,
+						 ~(u32)PCIE_ATU_ENABLE);
+		}
+	} else {
+		dw_pcie_writel_dbi(pci, PCIE_ATU_VIEWPORT, region | index);
+		dw_pcie_writel_dbi(pci, PCIE_ATU_CR2, ~(u32)PCIE_ATU_ENABLE);
+	}
 }
 
 int dw_pcie_wait_for_link(struct dw_pcie *pci)
@@ -671,10 +685,11 @@
 		if (!pci->atu_base) {
 			struct resource *res =
 				platform_get_resource_byname(pdev, IORESOURCE_MEM, "atu");
-			if (res)
+			if (res) {
 				pci->atu_size = resource_size(res);
-			pci->atu_base = devm_ioremap_resource(dev, res);
-			if (IS_ERR(pci->atu_base))
+				pci->atu_base = devm_ioremap_resource(dev, res);
+			}
+			if (!pci->atu_base || IS_ERR(pci->atu_base))
 				pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
 		}
 
@@ -715,7 +730,7 @@
 	if (pci->n_fts[1]) {
 		val = dw_pcie_readl_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL);
 		val &= ~PORT_LOGIC_N_FTS_MASK;
-		val |= pci->n_fts[pci->link_gen - 1];
+		val |= pci->n_fts[1];
 		dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
 	}
 
@@ -724,6 +739,13 @@
 	val |= PORT_LINK_DLL_LINK_EN;
 	dw_pcie_writel_dbi(pci, PCIE_PORT_LINK_CONTROL, val);
 
+	if (of_property_read_bool(np, "snps,enable-cdm-check")) {
+		val = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS);
+		val |= PCIE_PL_CHK_REG_CHK_REG_CONTINUOUS |
+		       PCIE_PL_CHK_REG_CHK_REG_START;
+		dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
+	}
+
 	of_property_read_u32(np, "num-lanes", &pci->num_lanes);
 	if (!pci->num_lanes) {
 		dev_dbg(pci->dev, "Using h/w default number of lanes\n");
@@ -770,11 +792,4 @@
 		break;
 	}
 	dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
-
-	if (of_property_read_bool(np, "snps,enable-cdm-check")) {
-		val = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS);
-		val |= PCIE_PL_CHK_REG_CHK_REG_CONTINUOUS |
-		       PCIE_PL_CHK_REG_CHK_REG_START;
-		dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
-	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-designware.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-designware.h
@@ -365,6 +365,20 @@
 	dw_pcie_writel_dbi(pci, reg, val);
 }
 
+static inline int dw_pcie_start_link(struct dw_pcie *pci)
+{
+	if (pci->ops && pci->ops->start_link)
+		return pci->ops->start_link(pci);
+
+	return 0;
+}
+
+static inline void dw_pcie_stop_link(struct dw_pcie *pci)
+{
+	if (pci->ops && pci->ops->stop_link)
+		pci->ops->stop_link(pci);
+}
+
 #ifdef CONFIG_PCIE_DW_HOST
 irqreturn_t dw_handle_msi_irq(struct pcie_port *pp);
 void dw_pcie_setup_rc(struct pcie_port *pp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-dw-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-dw-rockchip.c
@@ -148,7 +148,7 @@
 		return PTR_ERR(rockchip->apb_base);
 
 	rockchip->rst_gpio = devm_gpiod_get_optional(&pdev->dev, "reset",
-						     GPIOD_OUT_HIGH);
+						     GPIOD_OUT_LOW);
 	if (IS_ERR(rockchip->rst_gpio))
 		return PTR_ERR(rockchip->rst_gpio);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-fu740.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-fu740.c
@@ -181,10 +181,59 @@
 {
 	struct device *dev = pci->dev;
 	struct fu740_pcie *afp = dev_get_drvdata(dev);
+	u8 cap_exp = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	int ret;
+	u32 orig, tmp;
+
+	/*
+	 * Force 2.5GT/s when starting the link, due to some devices not
+	 * probing at higher speeds. This happens with the PCIe switch
+	 * on the Unmatched board when U-Boot has not initialised the PCIe.
+	 * The fix in U-Boot is to force 2.5GT/s, which then gets cleared
+	 * by the soft reset done by this driver.
+	 */
+	dev_dbg(dev, "cap_exp at %x\n", cap_exp);
+	dw_pcie_dbi_ro_wr_en(pci);
+
+	tmp = dw_pcie_readl_dbi(pci, cap_exp + PCI_EXP_LNKCAP);
+	orig = tmp & PCI_EXP_LNKCAP_SLS;
+	tmp &= ~PCI_EXP_LNKCAP_SLS;
+	tmp |= PCI_EXP_LNKCAP_SLS_2_5GB;
+	dw_pcie_writel_dbi(pci, cap_exp + PCI_EXP_LNKCAP, tmp);
 
 	/* Enable LTSSM */
 	writel_relaxed(0x1, afp->mgmt_base + PCIEX8MGMT_APP_LTSSM_ENABLE);
-	return 0;
+
+	ret = dw_pcie_wait_for_link(pci);
+	if (ret) {
+		dev_err(dev, "error: link did not start\n");
+		goto err;
+	}
+
+	tmp = dw_pcie_readl_dbi(pci, cap_exp + PCI_EXP_LNKCAP);
+	if ((tmp & PCI_EXP_LNKCAP_SLS) != orig) {
+		dev_dbg(dev, "changing speed back to original\n");
+
+		tmp &= ~PCI_EXP_LNKCAP_SLS;
+		tmp |= orig;
+		dw_pcie_writel_dbi(pci, cap_exp + PCI_EXP_LNKCAP, tmp);
+
+		tmp = dw_pcie_readl_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL);
+		tmp |= PORT_LOGIC_SPEED_CHANGE;
+		dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, tmp);
+
+		ret = dw_pcie_wait_for_link(pci);
+		if (ret) {
+			dev_err(dev, "error: link did not start at new speed\n");
+			goto err;
+		}
+	}
+
+	ret = 0;
+err:
+	WARN_ON(ret);	/* we assume that errors will be very rare */
+	dw_pcie_dbi_ro_wr_dis(pci);
+	return ret;
 }
 
 static int fu740_pcie_host_init(struct pcie_port *pp)
@@ -252,6 +301,7 @@
 	pci->dev = dev;
 	pci->ops = &dw_pcie_ops;
 	pci->pp.ops = &fu740_pcie_host_ops;
+	pci->pp.num_vectors = MAX_MSI_IRQS;
 
 	/* SiFive specific region: mgmt */
 	afp->mgmt_base = devm_platform_ioremap_resource_byname(pdev, "mgmt");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-qcom.c
@@ -325,8 +325,6 @@
 	reset_control_assert(res->ext_reset);
 	reset_control_assert(res->phy_reset);
 
-	writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
-
 	ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies);
 	if (ret < 0) {
 		dev_err(dev, "cannot enable regulators\n");
@@ -369,15 +367,15 @@
 		goto err_deassert_axi;
 	}
 
-	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
-	if (ret)
-		goto err_clks;
-
 	/* enable PCIe clocks and resets */
 	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
 	val &= ~BIT(0);
 	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
 
+	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	if (ret)
+		goto err_clks;
+
 	if (of_device_is_compatible(node, "qcom,pcie-ipq8064") ||
 	    of_device_is_compatible(node, "qcom,pcie-ipq8064-v2")) {
 		writel(PCS_DEEMPH_TX_DEEMPH_GEN1(24) |
@@ -1026,9 +1024,7 @@
 	struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
-	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
 	int i, ret;
-	u32 val;
 
 	for (i = 0; i < ARRAY_SIZE(res->rst); i++) {
 		ret = reset_control_assert(res->rst[i]);
@@ -1085,6 +1081,33 @@
 		goto err_clk_aux;
 	}
 
+	return 0;
+
+err_clk_aux:
+	clk_disable_unprepare(res->ahb_clk);
+err_clk_ahb:
+	clk_disable_unprepare(res->axi_s_clk);
+err_clk_axi_s:
+	clk_disable_unprepare(res->axi_m_clk);
+err_clk_axi_m:
+	clk_disable_unprepare(res->iface);
+err_clk_iface:
+	/*
+	 * Not checking for failure, will anyway return
+	 * the original failure in 'ret'.
+	 */
+	for (i = 0; i < ARRAY_SIZE(res->rst); i++)
+		reset_control_assert(res->rst[i]);
+
+	return ret;
+}
+
+static int qcom_pcie_post_init_2_3_3(struct qcom_pcie *pcie)
+{
+	struct dw_pcie *pci = pcie->pci;
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u32 val;
+
 	writel(SLV_ADDR_SPACE_SZ,
 		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
 
@@ -1111,25 +1134,9 @@
 	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
 		PCI_EXP_DEVCTL2);
 
-	return 0;
-
-err_clk_aux:
-	clk_disable_unprepare(res->ahb_clk);
-err_clk_ahb:
-	clk_disable_unprepare(res->axi_s_clk);
-err_clk_axi_s:
-	clk_disable_unprepare(res->axi_m_clk);
-err_clk_axi_m:
-	clk_disable_unprepare(res->iface);
-err_clk_iface:
-	/*
-	 * Not checking for failure, will anyway return
-	 * the original failure in 'ret'.
-	 */
-	for (i = 0; i < ARRAY_SIZE(res->rst); i++)
-		reset_control_assert(res->rst[i]);
+	dw_pcie_dbi_ro_wr_dis(pci);
 
-	return ret;
+	return 0;
 }
 
 static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
@@ -1203,12 +1210,6 @@
 		goto err_disable_clocks;
 	}
 
-	ret = clk_prepare_enable(res->pipe_clk);
-	if (ret) {
-		dev_err(dev, "cannot prepare/enable pipe clock\n");
-		goto err_disable_clocks;
-	}
-
 	/* configure PCIe to RC mode */
 	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
 
@@ -1229,11 +1230,9 @@
 	val |= BIT(4);
 	writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
 
-	if (IS_ENABLED(CONFIG_PCI_MSI)) {
-		val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT);
-		val |= BIT(31);
-		writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT);
-	}
+	val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2);
+	val |= BIT(31);
+	writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2);
 
 	return 0;
 err_disable_clocks:
@@ -1431,6 +1430,7 @@
 static const struct qcom_pcie_ops ops_2_3_3 = {
 	.get_resources = qcom_pcie_get_resources_2_3_3,
 	.init = qcom_pcie_init_2_3_3,
+	.post_init = qcom_pcie_post_init_2_3_3,
 	.deinit = qcom_pcie_deinit_2_3_3,
 	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
 };
@@ -1521,22 +1521,21 @@
 	pp->ops = &qcom_pcie_dw_ops;
 
 	ret = phy_init(pcie->phy);
-	if (ret) {
-		pm_runtime_disable(&pdev->dev);
+	if (ret)
 		goto err_pm_runtime_put;
-	}
 
 	platform_set_drvdata(pdev, pcie);
 
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(dev, "cannot initialize host\n");
-		pm_runtime_disable(&pdev->dev);
-		goto err_pm_runtime_put;
+		goto err_phy_exit;
 	}
 
 	return 0;
 
+err_phy_exit:
+	phy_exit(pcie->phy);
 err_pm_runtime_put:
 	pm_runtime_put(dev);
 	pm_runtime_disable(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-tegra194.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-tegra194.c
@@ -7,6 +7,7 @@
  * Author: Vidya Sagar <vidyas@nvidia.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/debugfs.h>
 #include <linux/delay.h>
@@ -239,6 +240,7 @@
 #define EP_STATE_ENABLED	1
 
 static const unsigned int pcie_gen_freq[] = {
+	GEN1_CORE_CLK_FREQ,	/* PCI_EXP_LNKSTA_CLS == 0; undefined */
 	GEN1_CORE_CLK_FREQ,
 	GEN2_CORE_CLK_FREQ,
 	GEN3_CORE_CLK_FREQ,
@@ -327,8 +329,7 @@
 	 */
 	val = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA);
 	if (val & PCI_EXP_LNKSTA_LBMS) {
-		current_link_width = (val & PCI_EXP_LNKSTA_NLW) >>
-				     PCI_EXP_LNKSTA_NLW_SHIFT;
+		current_link_width = FIELD_GET(PCI_EXP_LNKSTA_NLW, val);
 		if (pcie->init_link_width > current_link_width) {
 			dev_warn(pci->dev, "PCIe link is bad, width reduced\n");
 			val = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base +
@@ -352,15 +353,14 @@
 	struct tegra_pcie_dw *pcie = arg;
 	struct dw_pcie *pci = &pcie->pci;
 	struct pcie_port *pp = &pci->pp;
-	u32 val, tmp;
+	u32 val, status_l0, status_l1;
 	u16 val_w;
 
-	val = appl_readl(pcie, APPL_INTR_STATUS_L0);
-	if (val & APPL_INTR_STATUS_L0_LINK_STATE_INT) {
-		val = appl_readl(pcie, APPL_INTR_STATUS_L1_0_0);
-		if (val & APPL_INTR_STATUS_L1_0_0_LINK_REQ_RST_NOT_CHGED) {
-			appl_writel(pcie, val, APPL_INTR_STATUS_L1_0_0);
-
+	status_l0 = appl_readl(pcie, APPL_INTR_STATUS_L0);
+	if (status_l0 & APPL_INTR_STATUS_L0_LINK_STATE_INT) {
+		status_l1 = appl_readl(pcie, APPL_INTR_STATUS_L1_0_0);
+		appl_writel(pcie, status_l1, APPL_INTR_STATUS_L1_0_0);
+		if (status_l1 & APPL_INTR_STATUS_L1_0_0_LINK_REQ_RST_NOT_CHGED) {
 			/* SBR & Surprise Link Down WAR */
 			val = appl_readl(pcie, APPL_CAR_RESET_OVRD);
 			val &= ~APPL_CAR_RESET_OVRD_CYA_OVERRIDE_CORE_RST_N;
@@ -376,15 +376,15 @@
 		}
 	}
 
-	if (val & APPL_INTR_STATUS_L0_INT_INT) {
-		val = appl_readl(pcie, APPL_INTR_STATUS_L1_8_0);
-		if (val & APPL_INTR_STATUS_L1_8_0_AUTO_BW_INT_STS) {
+	if (status_l0 & APPL_INTR_STATUS_L0_INT_INT) {
+		status_l1 = appl_readl(pcie, APPL_INTR_STATUS_L1_8_0);
+		if (status_l1 & APPL_INTR_STATUS_L1_8_0_AUTO_BW_INT_STS) {
 			appl_writel(pcie,
 				    APPL_INTR_STATUS_L1_8_0_AUTO_BW_INT_STS,
 				    APPL_INTR_STATUS_L1_8_0);
 			apply_bad_link_workaround(pp);
 		}
-		if (val & APPL_INTR_STATUS_L1_8_0_BW_MGT_INT_STS) {
+		if (status_l1 & APPL_INTR_STATUS_L1_8_0_BW_MGT_INT_STS) {
 			appl_writel(pcie,
 				    APPL_INTR_STATUS_L1_8_0_BW_MGT_INT_STS,
 				    APPL_INTR_STATUS_L1_8_0);
@@ -396,25 +396,24 @@
 		}
 	}
 
-	val = appl_readl(pcie, APPL_INTR_STATUS_L0);
-	if (val & APPL_INTR_STATUS_L0_CDM_REG_CHK_INT) {
-		val = appl_readl(pcie, APPL_INTR_STATUS_L1_18);
-		tmp = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS);
-		if (val & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMPLT) {
+	if (status_l0 & APPL_INTR_STATUS_L0_CDM_REG_CHK_INT) {
+		status_l1 = appl_readl(pcie, APPL_INTR_STATUS_L1_18);
+		val = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS);
+		if (status_l1 & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMPLT) {
 			dev_info(pci->dev, "CDM check complete\n");
-			tmp |= PCIE_PL_CHK_REG_CHK_REG_COMPLETE;
+			val |= PCIE_PL_CHK_REG_CHK_REG_COMPLETE;
 		}
-		if (val & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMP_ERR) {
+		if (status_l1 & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_CMP_ERR) {
 			dev_err(pci->dev, "CDM comparison mismatch\n");
-			tmp |= PCIE_PL_CHK_REG_CHK_REG_COMPARISON_ERROR;
+			val |= PCIE_PL_CHK_REG_CHK_REG_COMPARISON_ERROR;
 		}
-		if (val & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_LOGIC_ERR) {
+		if (status_l1 & APPL_INTR_STATUS_L1_18_CDM_REG_CHK_LOGIC_ERR) {
 			dev_err(pci->dev, "CDM Logic error\n");
-			tmp |= PCIE_PL_CHK_REG_CHK_REG_LOGIC_ERROR;
+			val |= PCIE_PL_CHK_REG_CHK_REG_LOGIC_ERROR;
 		}
-		dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, tmp);
-		tmp = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_ERR_ADDR);
-		dev_err(pci->dev, "CDM Error Address Offset = 0x%08X\n", tmp);
+		dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
+		val = dw_pcie_readl_dbi(pci, PCIE_PL_CHK_REG_ERR_ADDR);
+		dev_err(pci->dev, "CDM Error Address Offset = 0x%08X\n", val);
 	}
 
 	return IRQ_HANDLED;
@@ -454,7 +453,11 @@
 
 	speed = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA) &
 		PCI_EXP_LNKSTA_CLS;
-	clk_set_rate(pcie->core_clk, pcie_gen_freq[speed - 1]);
+
+	if (speed >= ARRAY_SIZE(pcie_gen_freq))
+		speed = 0;
+
+	clk_set_rate(pcie->core_clk, pcie_gen_freq[speed]);
 
 	/* If EP doesn't advertise L1SS, just return */
 	val = dw_pcie_readl_dbi(pci, pcie->cfg_link_cap_l1sub);
@@ -728,8 +731,7 @@
 
 	val_w = dw_pcie_readw_dbi(&pcie->pci, pcie->pcie_cap_base +
 				  PCI_EXP_LNKSTA);
-	pcie->init_link_width = (val_w & PCI_EXP_LNKSTA_NLW) >>
-				PCI_EXP_LNKSTA_NLW_SHIFT;
+	pcie->init_link_width = FIELD_GET(PCI_EXP_LNKSTA_NLW, val_w);
 
 	val_w = dw_pcie_readw_dbi(&pcie->pci, pcie->pcie_cap_base +
 				  PCI_EXP_LNKCTL);
@@ -886,7 +888,7 @@
 	/* Configure Max lane width from DT */
 	val = dw_pcie_readl_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKCAP);
 	val &= ~PCI_EXP_LNKCAP_MLW;
-	val |= (pcie->num_lanes << PCI_EXP_LNKSTA_NLW_SHIFT);
+	val |= FIELD_PREP(PCI_EXP_LNKCAP_MLW, pcie->num_lanes);
 	dw_pcie_writel_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKCAP, val);
 
 	config_gen3_gen4_eq_presets(pcie);
@@ -980,7 +982,7 @@
 		offset = dw_pcie_find_ext_capability(pci, PCI_EXT_CAP_ID_DLF);
 		val = dw_pcie_readl_dbi(pci, offset + PCI_DLF_CAP);
 		val &= ~PCI_DLF_EXCHANGE_ENABLE;
-		dw_pcie_writel_dbi(pci, offset, val);
+		dw_pcie_writel_dbi(pci, offset + PCI_DLF_CAP, val);
 
 		tegra_pcie_dw_host_init(pp);
 		dw_pcie_setup_rc(pp);
@@ -991,7 +993,11 @@
 
 	speed = dw_pcie_readw_dbi(pci, pcie->pcie_cap_base + PCI_EXP_LNKSTA) &
 		PCI_EXP_LNKSTA_CLS;
-	clk_set_rate(pcie->core_clk, pcie_gen_freq[speed - 1]);
+
+	if (speed >= ARRAY_SIZE(pcie_gen_freq))
+		speed = 0;
+
+	clk_set_rate(pcie->core_clk, pcie_gen_freq[speed]);
 
 	tegra_pcie_enable_interrupts(pp);
 
@@ -1951,6 +1957,7 @@
 	if (ret) {
 		dev_err(dev, "Failed to initialize DWC Endpoint subsystem: %d\n",
 			ret);
+		pm_runtime_disable(dev);
 		return ret;
 	}
 
@@ -2135,10 +2142,13 @@
 		ret = tegra_pcie_config_ep(pcie, pdev);
 		if (ret < 0)
 			goto fail;
+		else
+			return 0;
 		break;
 
 	default:
 		dev_err(dev, "Invalid PCIe device type %d\n", pcie->mode);
+		ret = -EINVAL;
 	}
 
 fail:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/dwc/pcie-uniphier.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/dwc/pcie-uniphier.c
@@ -168,30 +168,21 @@
 	writel(PCL_RCV_INTX_ALL_ENABLE, priv->base + PCL_RCV_INTX);
 }
 
-static void uniphier_pcie_irq_ack(struct irq_data *d)
-{
-	struct pcie_port *pp = irq_data_get_irq_chip_data(d);
-	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
-	struct uniphier_pcie_priv *priv = to_uniphier_pcie(pci);
-	u32 val;
-
-	val = readl(priv->base + PCL_RCV_INTX);
-	val &= ~PCL_RCV_INTX_ALL_STATUS;
-	val |= BIT(irqd_to_hwirq(d) + PCL_RCV_INTX_STATUS_SHIFT);
-	writel(val, priv->base + PCL_RCV_INTX);
-}
-
 static void uniphier_pcie_irq_mask(struct irq_data *d)
 {
 	struct pcie_port *pp = irq_data_get_irq_chip_data(d);
 	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
 	struct uniphier_pcie_priv *priv = to_uniphier_pcie(pci);
+	unsigned long flags;
 	u32 val;
 
+	raw_spin_lock_irqsave(&pp->lock, flags);
+
 	val = readl(priv->base + PCL_RCV_INTX);
-	val &= ~PCL_RCV_INTX_ALL_MASK;
 	val |= BIT(irqd_to_hwirq(d) + PCL_RCV_INTX_MASK_SHIFT);
 	writel(val, priv->base + PCL_RCV_INTX);
+
+	raw_spin_unlock_irqrestore(&pp->lock, flags);
 }
 
 static void uniphier_pcie_irq_unmask(struct irq_data *d)
@@ -199,17 +190,20 @@
 	struct pcie_port *pp = irq_data_get_irq_chip_data(d);
 	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
 	struct uniphier_pcie_priv *priv = to_uniphier_pcie(pci);
+	unsigned long flags;
 	u32 val;
 
+	raw_spin_lock_irqsave(&pp->lock, flags);
+
 	val = readl(priv->base + PCL_RCV_INTX);
-	val &= ~PCL_RCV_INTX_ALL_MASK;
 	val &= ~BIT(irqd_to_hwirq(d) + PCL_RCV_INTX_MASK_SHIFT);
 	writel(val, priv->base + PCL_RCV_INTX);
+
+	raw_spin_unlock_irqrestore(&pp->lock, flags);
 }
 
 static struct irq_chip uniphier_pcie_irq_chip = {
 	.name = "PCI",
-	.irq_ack = uniphier_pcie_irq_ack,
 	.irq_mask = uniphier_pcie_irq_mask,
 	.irq_unmask = uniphier_pcie_irq_unmask,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pci-aardvark.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pci-aardvark.c
@@ -8,6 +8,7 @@
  * Author: Hezi Shahmoon <hezi.shahmoon@marvell.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/delay.h>
 #include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
@@ -31,9 +32,6 @@
 /* PCIe core registers */
 #define PCIE_CORE_DEV_ID_REG					0x0
 #define PCIE_CORE_CMD_STATUS_REG				0x4
-#define     PCIE_CORE_CMD_IO_ACCESS_EN				BIT(0)
-#define     PCIE_CORE_CMD_MEM_ACCESS_EN				BIT(1)
-#define     PCIE_CORE_CMD_MEM_IO_REQ_EN				BIT(2)
 #define PCIE_CORE_DEV_REV_REG					0x8
 #define PCIE_CORE_PCIEXP_CAP					0xc0
 #define PCIE_CORE_ERR_CAPCTL_REG				0x118
@@ -41,10 +39,6 @@
 #define     PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX_EN			BIT(6)
 #define     PCIE_CORE_ERR_CAPCTL_ECRC_CHCK			BIT(7)
 #define     PCIE_CORE_ERR_CAPCTL_ECRC_CHCK_RCV			BIT(8)
-#define     PCIE_CORE_INT_A_ASSERT_ENABLE			1
-#define     PCIE_CORE_INT_B_ASSERT_ENABLE			2
-#define     PCIE_CORE_INT_C_ASSERT_ENABLE			3
-#define     PCIE_CORE_INT_D_ASSERT_ENABLE			4
 /* PIO registers base address and register offsets */
 #define PIO_BASE_ADDR				0x4000
 #define PIO_CTRL				(PIO_BASE_ADDR + 0x0)
@@ -99,25 +93,32 @@
 #define     PCIE_CORE_CTRL2_MSI_ENABLE		BIT(10)
 #define PCIE_CORE_REF_CLK_REG			(CONTROL_BASE_ADDR + 0x14)
 #define     PCIE_CORE_REF_CLK_TX_ENABLE		BIT(1)
+#define     PCIE_CORE_REF_CLK_RX_ENABLE		BIT(2)
 #define PCIE_MSG_LOG_REG			(CONTROL_BASE_ADDR + 0x30)
 #define PCIE_ISR0_REG				(CONTROL_BASE_ADDR + 0x40)
 #define PCIE_MSG_PM_PME_MASK			BIT(7)
 #define PCIE_ISR0_MASK_REG			(CONTROL_BASE_ADDR + 0x44)
 #define     PCIE_ISR0_MSI_INT_PENDING		BIT(24)
+#define     PCIE_ISR0_CORR_ERR			BIT(11)
+#define     PCIE_ISR0_NFAT_ERR			BIT(12)
+#define     PCIE_ISR0_FAT_ERR			BIT(13)
+#define     PCIE_ISR0_ERR_MASK			GENMASK(13, 11)
 #define     PCIE_ISR0_INTX_ASSERT(val)		BIT(16 + (val))
 #define     PCIE_ISR0_INTX_DEASSERT(val)	BIT(20 + (val))
-#define	    PCIE_ISR0_ALL_MASK			GENMASK(26, 0)
+#define     PCIE_ISR0_ALL_MASK			GENMASK(31, 0)
 #define PCIE_ISR1_REG				(CONTROL_BASE_ADDR + 0x48)
 #define PCIE_ISR1_MASK_REG			(CONTROL_BASE_ADDR + 0x4C)
 #define     PCIE_ISR1_POWER_STATE_CHANGE	BIT(4)
 #define     PCIE_ISR1_FLUSH			BIT(5)
 #define     PCIE_ISR1_INTX_ASSERT(val)		BIT(8 + (val))
-#define     PCIE_ISR1_ALL_MASK			GENMASK(11, 4)
+#define     PCIE_ISR1_ALL_MASK			GENMASK(31, 0)
 #define PCIE_MSI_ADDR_LOW_REG			(CONTROL_BASE_ADDR + 0x50)
 #define PCIE_MSI_ADDR_HIGH_REG			(CONTROL_BASE_ADDR + 0x54)
 #define PCIE_MSI_STATUS_REG			(CONTROL_BASE_ADDR + 0x58)
 #define PCIE_MSI_MASK_REG			(CONTROL_BASE_ADDR + 0x5C)
+#define     PCIE_MSI_ALL_MASK			GENMASK(31, 0)
 #define PCIE_MSI_PAYLOAD_REG			(CONTROL_BASE_ADDR + 0x9C)
+#define     PCIE_MSI_DATA_MASK			GENMASK(15, 0)
 
 /* PCIe window configuration */
 #define OB_WIN_BASE_ADDR			0x4c00
@@ -164,8 +165,50 @@
 #define CFG_REG					(LMI_BASE_ADDR + 0x0)
 #define     LTSSM_SHIFT				24
 #define     LTSSM_MASK				0x3f
-#define     LTSSM_L0				0x10
 #define     RC_BAR_CONFIG			0x300
+
+/* LTSSM values in CFG_REG */
+enum {
+	LTSSM_DETECT_QUIET			= 0x0,
+	LTSSM_DETECT_ACTIVE			= 0x1,
+	LTSSM_POLLING_ACTIVE			= 0x2,
+	LTSSM_POLLING_COMPLIANCE		= 0x3,
+	LTSSM_POLLING_CONFIGURATION		= 0x4,
+	LTSSM_CONFIG_LINKWIDTH_START		= 0x5,
+	LTSSM_CONFIG_LINKWIDTH_ACCEPT		= 0x6,
+	LTSSM_CONFIG_LANENUM_ACCEPT		= 0x7,
+	LTSSM_CONFIG_LANENUM_WAIT		= 0x8,
+	LTSSM_CONFIG_COMPLETE			= 0x9,
+	LTSSM_CONFIG_IDLE			= 0xa,
+	LTSSM_RECOVERY_RCVR_LOCK		= 0xb,
+	LTSSM_RECOVERY_SPEED			= 0xc,
+	LTSSM_RECOVERY_RCVR_CFG			= 0xd,
+	LTSSM_RECOVERY_IDLE			= 0xe,
+	LTSSM_L0				= 0x10,
+	LTSSM_RX_L0S_ENTRY			= 0x11,
+	LTSSM_RX_L0S_IDLE			= 0x12,
+	LTSSM_RX_L0S_FTS			= 0x13,
+	LTSSM_TX_L0S_ENTRY			= 0x14,
+	LTSSM_TX_L0S_IDLE			= 0x15,
+	LTSSM_TX_L0S_FTS			= 0x16,
+	LTSSM_L1_ENTRY				= 0x17,
+	LTSSM_L1_IDLE				= 0x18,
+	LTSSM_L2_IDLE				= 0x19,
+	LTSSM_L2_TRANSMIT_WAKE			= 0x1a,
+	LTSSM_DISABLED				= 0x20,
+	LTSSM_LOOPBACK_ENTRY_MASTER		= 0x21,
+	LTSSM_LOOPBACK_ACTIVE_MASTER		= 0x22,
+	LTSSM_LOOPBACK_EXIT_MASTER		= 0x23,
+	LTSSM_LOOPBACK_ENTRY_SLAVE		= 0x24,
+	LTSSM_LOOPBACK_ACTIVE_SLAVE		= 0x25,
+	LTSSM_LOOPBACK_EXIT_SLAVE		= 0x26,
+	LTSSM_HOT_RESET				= 0x27,
+	LTSSM_RECOVERY_EQUALIZATION_PHASE0	= 0x28,
+	LTSSM_RECOVERY_EQUALIZATION_PHASE1	= 0x29,
+	LTSSM_RECOVERY_EQUALIZATION_PHASE2	= 0x2a,
+	LTSSM_RECOVERY_EQUALIZATION_PHASE3	= 0x2b,
+};
+
 #define VENDOR_ID_REG				(LMI_BASE_ADDR + 0x44)
 
 /* PCIe core controller registers */
@@ -198,7 +241,7 @@
 #define     PCIE_IRQ_MSI_INT2_DET		BIT(21)
 #define     PCIE_IRQ_RC_DBELL_DET		BIT(22)
 #define     PCIE_IRQ_EP_STATUS			BIT(23)
-#define     PCIE_IRQ_ALL_MASK			0xfff0fb
+#define     PCIE_IRQ_ALL_MASK			GENMASK(31, 0)
 #define     PCIE_IRQ_ENABLE_INTS_MASK		PCIE_IRQ_CORE_INT
 
 /* Transaction types */
@@ -230,17 +273,15 @@
 		u32 actions;
 	} wins[OB_WIN_COUNT];
 	u8 wins_count;
+	struct irq_domain *rp_irq_domain;
 	struct irq_domain *irq_domain;
 	struct irq_chip irq_chip;
 	raw_spinlock_t irq_lock;
 	struct irq_domain *msi_domain;
 	struct irq_domain *msi_inner_domain;
-	struct irq_chip msi_bottom_irq_chip;
-	struct irq_chip msi_irq_chip;
-	struct msi_domain_info msi_domain_info;
+	raw_spinlock_t msi_irq_lock;
 	DECLARE_BITMAP(msi_used, MSI_IRQ_NUM);
 	struct mutex msi_used_lock;
-	u16 msi_msg;
 	int link_gen;
 	struct pci_bridge_emul bridge;
 	struct gpio_desc *reset_gpio;
@@ -257,18 +298,49 @@
 	return readl(pcie->base + reg);
 }
 
-static inline u16 advk_read16(struct advk_pcie *pcie, u64 reg)
+static u8 advk_pcie_ltssm_state(struct advk_pcie *pcie)
 {
-	return advk_readl(pcie, (reg & ~0x3)) >> ((reg & 0x3) * 8);
+	u32 val;
+	u8 ltssm_state;
+
+	val = advk_readl(pcie, CFG_REG);
+	ltssm_state = (val >> LTSSM_SHIFT) & LTSSM_MASK;
+	return ltssm_state;
 }
 
-static int advk_pcie_link_up(struct advk_pcie *pcie)
+static inline bool advk_pcie_link_up(struct advk_pcie *pcie)
 {
-	u32 val, ltssm_state;
+	/* check if LTSSM is in normal operation - some L* state */
+	u8 ltssm_state = advk_pcie_ltssm_state(pcie);
+	return ltssm_state >= LTSSM_L0 && ltssm_state < LTSSM_DISABLED;
+}
 
-	val = advk_readl(pcie, CFG_REG);
-	ltssm_state = (val >> LTSSM_SHIFT) & LTSSM_MASK;
-	return ltssm_state >= LTSSM_L0;
+static inline bool advk_pcie_link_active(struct advk_pcie *pcie)
+{
+	/*
+	 * According to PCIe Base specification 3.0, Table 4-14: Link
+	 * Status Mapped to the LTSSM, and 4.2.6.3.6 Configuration.Idle
+	 * is Link Up mapped to LTSSM Configuration.Idle, Recovery, L0,
+	 * L0s, L1 and L2 states. And according to 3.2.1. Data Link
+	 * Control and Management State Machine Rules is DL Up status
+	 * reported in DL Active state.
+	 */
+	u8 ltssm_state = advk_pcie_ltssm_state(pcie);
+	return ltssm_state >= LTSSM_CONFIG_IDLE && ltssm_state < LTSSM_DISABLED;
+}
+
+static inline bool advk_pcie_link_training(struct advk_pcie *pcie)
+{
+	/*
+	 * According to PCIe Base specification 3.0, Table 4-14: Link
+	 * Status Mapped to the LTSSM is Link Training mapped to LTSSM
+	 * Configuration and Recovery states.
+	 */
+	u8 ltssm_state = advk_pcie_ltssm_state(pcie);
+	return ((ltssm_state >= LTSSM_CONFIG_LINKWIDTH_START &&
+		 ltssm_state < LTSSM_L0) ||
+		(ltssm_state >= LTSSM_RECOVERY_EQUALIZATION_PHASE0 &&
+		 ltssm_state <= LTSSM_RECOVERY_EQUALIZATION_PHASE3));
 }
 
 static int advk_pcie_wait_for_link(struct advk_pcie *pcie)
@@ -291,7 +363,7 @@
 	size_t retries;
 
 	for (retries = 0; retries < RETRAIN_WAIT_MAX_RETRIES; ++retries) {
-		if (!advk_pcie_link_up(pcie))
+		if (advk_pcie_link_training(pcie))
 			break;
 		udelay(RETRAIN_WAIT_USLEEP_US);
 	}
@@ -299,23 +371,9 @@
 
 static void advk_pcie_issue_perst(struct advk_pcie *pcie)
 {
-	u32 reg;
-
 	if (!pcie->reset_gpio)
 		return;
 
-	/*
-	 * As required by PCI Express spec (PCI Express Base Specification, REV.
-	 * 4.0 PCI Express, February 19 2014, 6.6.1 Conventional Reset) a delay
-	 * for at least 100ms after de-asserting PERST# signal is needed before
-	 * link training is enabled. So ensure that link training is disabled
-	 * prior de-asserting PERST# signal to fulfill that PCI Express spec
-	 * requirement.
-	 */
-	reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
-	reg &= ~LINK_TRAINING_EN;
-	advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
-
 	/* 10ms delay is needed for some cards */
 	dev_info(&pcie->pdev->dev, "issuing PERST via reset GPIO for 10ms\n");
 	gpiod_set_value_cansleep(pcie->reset_gpio, 1);
@@ -323,54 +381,47 @@
 	gpiod_set_value_cansleep(pcie->reset_gpio, 0);
 }
 
-static int advk_pcie_train_at_gen(struct advk_pcie *pcie, int gen)
+static void advk_pcie_train_link(struct advk_pcie *pcie)
 {
-	int ret, neg_gen;
+	struct device *dev = &pcie->pdev->dev;
 	u32 reg;
+	int ret;
 
-	/* Setup link speed */
+	/*
+	 * Setup PCIe rev / gen compliance based on device tree property
+	 * 'max-link-speed' which also forces maximal link speed.
+	 */
 	reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
 	reg &= ~PCIE_GEN_SEL_MSK;
-	if (gen == 3)
+	if (pcie->link_gen == 3)
 		reg |= SPEED_GEN_3;
-	else if (gen == 2)
+	else if (pcie->link_gen == 2)
 		reg |= SPEED_GEN_2;
 	else
 		reg |= SPEED_GEN_1;
 	advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
 
 	/*
-	 * Enable link training. This is not needed in every call to this
-	 * function, just once suffices, but it does not break anything either.
+	 * Set maximal link speed value also into PCIe Link Control 2 register.
+	 * Armada 3700 Functional Specification says that default value is based
+	 * on SPEED_GEN but tests showed that default value is always 8.0 GT/s.
 	 */
+	reg = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKCTL2);
+	reg &= ~PCI_EXP_LNKCTL2_TLS;
+	if (pcie->link_gen == 3)
+		reg |= PCI_EXP_LNKCTL2_TLS_8_0GT;
+	else if (pcie->link_gen == 2)
+		reg |= PCI_EXP_LNKCTL2_TLS_5_0GT;
+	else
+		reg |= PCI_EXP_LNKCTL2_TLS_2_5GT;
+	advk_writel(pcie, reg, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKCTL2);
+
+	/* Enable link training after selecting PCIe generation */
 	reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
 	reg |= LINK_TRAINING_EN;
 	advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
 
 	/*
-	 * Start link training immediately after enabling it.
-	 * This solves problems for some buggy cards.
-	 */
-	reg = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKCTL);
-	reg |= PCI_EXP_LNKCTL_RL;
-	advk_writel(pcie, reg, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKCTL);
-
-	ret = advk_pcie_wait_for_link(pcie);
-	if (ret)
-		return ret;
-
-	reg = advk_read16(pcie, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKSTA);
-	neg_gen = reg & PCI_EXP_LNKSTA_CLS;
-
-	return neg_gen;
-}
-
-static void advk_pcie_train_link(struct advk_pcie *pcie)
-{
-	struct device *dev = &pcie->pdev->dev;
-	int neg_gen = -1, gen;
-
-	/*
 	 * Reset PCIe card via PERST# signal. Some cards are not detected
 	 * during link training when they are in some non-initial state.
 	 */
@@ -380,41 +431,18 @@
 	 * PERST# signal could have been asserted by pinctrl subsystem before
 	 * probe() callback has been called or issued explicitly by reset gpio
 	 * function advk_pcie_issue_perst(), making the endpoint going into
-	 * fundamental reset. As required by PCI Express spec a delay for at
-	 * least 100ms after such a reset before link training is needed.
-	 */
-	msleep(PCI_PM_D3COLD_WAIT);
-
-	/*
-	 * Try link training at link gen specified by device tree property
-	 * 'max-link-speed'. If this fails, iteratively train at lower gen.
+	 * fundamental reset. As required by PCI Express spec (PCI Express
+	 * Base Specification, REV. 4.0 PCI Express, February 19 2014, 6.6.1
+	 * Conventional Reset) a delay for at least 100ms after such a reset
+	 * before sending a Configuration Request to the device is needed.
+	 * So wait until PCIe link is up. Function advk_pcie_wait_for_link()
+	 * waits for link at least 900ms.
 	 */
-	for (gen = pcie->link_gen; gen > 0; --gen) {
-		neg_gen = advk_pcie_train_at_gen(pcie, gen);
-		if (neg_gen > 0)
-			break;
-	}
-
-	if (neg_gen < 0)
-		goto err;
-
-	/*
-	 * After successful training if negotiated gen is lower than requested,
-	 * train again on negotiated gen. This solves some stability issues for
-	 * some buggy gen1 cards.
-	 */
-	if (neg_gen < gen) {
-		gen = neg_gen;
-		neg_gen = advk_pcie_train_at_gen(pcie, gen);
-	}
-
-	if (neg_gen == gen) {
-		dev_info(dev, "link up at gen %i\n", gen);
-		return;
-	}
-
-err:
-	dev_err(dev, "link never came up\n");
+	ret = advk_pcie_wait_for_link(pcie);
+	if (ret < 0)
+		dev_err(dev, "link never came up\n");
+	else
+		dev_info(dev, "link up\n");
 }
 
 /*
@@ -448,12 +476,19 @@
 
 static void advk_pcie_setup_hw(struct advk_pcie *pcie)
 {
+	phys_addr_t msi_addr;
 	u32 reg;
 	int i;
 
-	/* Enable TX */
+	/*
+	 * Configure PCIe Reference clock. Direction is from the PCIe
+	 * controller to the endpoint card, so enable transmitting of
+	 * Reference clock differential signal off-chip and disable
+	 * receiving off-chip differential signal.
+	 */
 	reg = advk_readl(pcie, PCIE_CORE_REF_CLK_REG);
 	reg |= PCIE_CORE_REF_CLK_TX_ENABLE;
+	reg &= ~PCIE_CORE_REF_CLK_RX_ENABLE;
 	advk_writel(pcie, reg, PCIE_CORE_REF_CLK_REG);
 
 	/* Set to Direct mode */
@@ -477,6 +512,31 @@
 	reg = (PCI_VENDOR_ID_MARVELL << 16) | PCI_VENDOR_ID_MARVELL;
 	advk_writel(pcie, reg, VENDOR_ID_REG);
 
+	/*
+	 * Change Class Code of PCI Bridge device to PCI Bridge (0x600400),
+	 * because the default value is Mass storage controller (0x010400).
+	 *
+	 * Note that this Aardvark PCI Bridge does not have compliant Type 1
+	 * Configuration Space and it even cannot be accessed via Aardvark's
+	 * PCI config space access method. Something like config space is
+	 * available in internal Aardvark registers starting at offset 0x0
+	 * and is reported as Type 0. In range 0x10 - 0x34 it has totally
+	 * different registers.
+	 *
+	 * Therefore driver uses emulation of PCI Bridge which emulates
+	 * access to configuration space via internal Aardvark registers or
+	 * emulated configuration buffer.
+	 */
+	reg = advk_readl(pcie, PCIE_CORE_DEV_REV_REG);
+	reg &= ~0xffffff00;
+	reg |= (PCI_CLASS_BRIDGE_PCI << 8) << 8;
+	advk_writel(pcie, reg, PCIE_CORE_DEV_REV_REG);
+
+	/* Disable Root Bridge I/O space, memory space and bus mastering */
+	reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
+	reg &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	advk_writel(pcie, reg, PCIE_CORE_CMD_STATUS_REG);
+
 	/* Set Advanced Error Capabilities and Control PF0 register */
 	reg = PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX |
 		PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX_EN |
@@ -488,8 +548,9 @@
 	reg = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + PCI_EXP_DEVCTL);
 	reg &= ~PCI_EXP_DEVCTL_RELAX_EN;
 	reg &= ~PCI_EXP_DEVCTL_NOSNOOP_EN;
+	reg &= ~PCI_EXP_DEVCTL_PAYLOAD;
 	reg &= ~PCI_EXP_DEVCTL_READRQ;
-	reg |= PCI_EXP_DEVCTL_PAYLOAD; /* Set max payload size */
+	reg |= PCI_EXP_DEVCTL_PAYLOAD_512B;
 	reg |= PCI_EXP_DEVCTL_READRQ_512B;
 	advk_writel(pcie, reg, PCIE_CORE_PCIEXP_CAP + PCI_EXP_DEVCTL);
 
@@ -504,25 +565,36 @@
 	reg |= LANE_COUNT_1;
 	advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
 
+	/* Set MSI address */
+	msi_addr = virt_to_phys(pcie);
+	advk_writel(pcie, lower_32_bits(msi_addr), PCIE_MSI_ADDR_LOW_REG);
+	advk_writel(pcie, upper_32_bits(msi_addr), PCIE_MSI_ADDR_HIGH_REG);
+
 	/* Enable MSI */
 	reg = advk_readl(pcie, PCIE_CORE_CTRL2_REG);
 	reg |= PCIE_CORE_CTRL2_MSI_ENABLE;
 	advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG);
 
 	/* Clear all interrupts */
+	advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_STATUS_REG);
 	advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_REG);
 	advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_REG);
 	advk_writel(pcie, PCIE_IRQ_ALL_MASK, HOST_CTRL_INT_STATUS_REG);
 
-	/* Disable All ISR0/1 Sources */
-	reg = PCIE_ISR0_ALL_MASK;
+	/* Disable All ISR0/1 and MSI Sources */
+	advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_MASK_REG);
+	advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_MASK_REG);
+	advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_MASK_REG);
+
+	/* Unmask summary MSI interrupt */
+	reg = advk_readl(pcie, PCIE_ISR0_MASK_REG);
 	reg &= ~PCIE_ISR0_MSI_INT_PENDING;
 	advk_writel(pcie, reg, PCIE_ISR0_MASK_REG);
 
-	advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_MASK_REG);
-
-	/* Unmask all MSIs */
-	advk_writel(pcie, 0, PCIE_MSI_MASK_REG);
+	/* Unmask PME interrupt for processing of PME requester */
+	reg = advk_readl(pcie, PCIE_ISR0_MASK_REG);
+	reg &= ~PCIE_MSG_PM_PME_MASK;
+	advk_writel(pcie, reg, PCIE_ISR0_MASK_REG);
 
 	/* Enable summary interrupt for GIC SPI source */
 	reg = PCIE_IRQ_ALL_MASK & (~PCIE_IRQ_ENABLE_INTS_MASK);
@@ -574,19 +646,6 @@
 		advk_pcie_disable_ob_win(pcie, i);
 
 	advk_pcie_train_link(pcie);
-
-	/*
-	 * FIXME: The following register update is suspicious. This register is
-	 * applicable only when the PCI controller is configured for Endpoint
-	 * mode, not as a Root Complex. But apparently when this code is
-	 * removed, some cards stop working. This should be investigated and
-	 * a comment explaining this should be put here.
-	 */
-	reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
-	reg |= PCIE_CORE_CMD_MEM_ACCESS_EN |
-		PCIE_CORE_CMD_IO_ACCESS_EN |
-		PCIE_CORE_CMD_MEM_IO_REQ_EN;
-	advk_writel(pcie, reg, PCIE_CORE_CMD_STATUS_REG);
 }
 
 static int advk_pcie_check_pio_status(struct advk_pcie *pcie, bool allow_crs, u32 *val)
@@ -595,6 +654,7 @@
 	u32 reg;
 	unsigned int status;
 	char *strcomp_status, *str_posted;
+	int ret;
 
 	reg = advk_readl(pcie, PIO_STAT);
 	status = (reg & PIO_COMPLETION_STATUS_MASK) >>
@@ -619,6 +679,7 @@
 	case PIO_COMPLETION_STATUS_OK:
 		if (reg & PIO_ERR_STATUS) {
 			strcomp_status = "COMP_ERR";
+			ret = -EFAULT;
 			break;
 		}
 		/* Get the read result */
@@ -626,9 +687,11 @@
 			*val = advk_readl(pcie, PIO_RD_DATA);
 		/* No error */
 		strcomp_status = NULL;
+		ret = 0;
 		break;
 	case PIO_COMPLETION_STATUS_UR:
 		strcomp_status = "UR";
+		ret = -EOPNOTSUPP;
 		break;
 	case PIO_COMPLETION_STATUS_CRS:
 		if (allow_crs && val) {
@@ -646,6 +709,7 @@
 			 */
 			*val = CFG_RD_CRS_VAL;
 			strcomp_status = NULL;
+			ret = 0;
 			break;
 		}
 		/* PCIe r4.0, sec 2.3.2, says:
@@ -661,31 +725,34 @@
 		 * Request and taking appropriate action, e.g., complete the
 		 * Request to the host as a failed transaction.
 		 *
-		 * To simplify implementation do not re-issue the Configuration
-		 * Request and complete the Request as a failed transaction.
+		 * So return -EAGAIN and caller (pci-aardvark.c driver) will
+		 * re-issue request again up to the PIO_RETRY_CNT retries.
 		 */
 		strcomp_status = "CRS";
+		ret = -EAGAIN;
 		break;
 	case PIO_COMPLETION_STATUS_CA:
 		strcomp_status = "CA";
+		ret = -ECANCELED;
 		break;
 	default:
 		strcomp_status = "Unknown";
+		ret = -EINVAL;
 		break;
 	}
 
 	if (!strcomp_status)
-		return 0;
+		return ret;
 
 	if (reg & PIO_NON_POSTED_REQ)
 		str_posted = "Non-posted";
 	else
 		str_posted = "Posted";
 
-	dev_err(dev, "%s PIO Response Status: %s, %#x @ %#x\n",
+	dev_dbg(dev, "%s PIO Response Status: %s, %#x @ %#x\n",
 		str_posted, strcomp_status, reg, advk_readl(pcie, PIO_ADDR_LS));
 
-	return -EFAULT;
+	return ret;
 }
 
 static int advk_pcie_wait_pio(struct advk_pcie *pcie)
@@ -693,13 +760,13 @@
 	struct device *dev = &pcie->pdev->dev;
 	int i;
 
-	for (i = 0; i < PIO_RETRY_CNT; i++) {
+	for (i = 1; i <= PIO_RETRY_CNT; i++) {
 		u32 start, isr;
 
 		start = advk_readl(pcie, PIO_START);
 		isr = advk_readl(pcie, PIO_ISR);
 		if (!start && isr)
-			return 0;
+			return i;
 		udelay(PIO_RETRY_DELAY);
 	}
 
@@ -707,30 +774,106 @@
 	return -ETIMEDOUT;
 }
 
-
 static pci_bridge_emul_read_status_t
-advk_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
+advk_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,
 				    int reg, u32 *value)
 {
 	struct advk_pcie *pcie = bridge->data;
 
-
 	switch (reg) {
-	case PCI_EXP_SLTCTL:
-		*value = PCI_EXP_SLTSTA_PDS << 16;
+	case PCI_COMMAND:
+		*value = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
 		return PCI_BRIDGE_EMUL_HANDLED;
 
-	case PCI_EXP_RTCTL: {
-		u32 val = advk_readl(pcie, PCIE_ISR0_MASK_REG);
-		*value = (val & PCIE_MSG_PM_PME_MASK) ? 0 : PCI_EXP_RTCTL_PMEIE;
-		*value |= PCI_EXP_RTCAP_CRSVIS << 16;
+	case PCI_INTERRUPT_LINE: {
+		/*
+		 * From the whole 32bit register we support reading from HW only
+		 * two bits: PCI_BRIDGE_CTL_BUS_RESET and PCI_BRIDGE_CTL_SERR.
+		 * Other bits are retrieved only from emulated config buffer.
+		 */
+		__le32 *cfgspace = (__le32 *)&bridge->conf;
+		u32 val = le32_to_cpu(cfgspace[PCI_INTERRUPT_LINE / 4]);
+		if (advk_readl(pcie, PCIE_ISR0_MASK_REG) & PCIE_ISR0_ERR_MASK)
+			val &= ~(PCI_BRIDGE_CTL_SERR << 16);
+		else
+			val |= PCI_BRIDGE_CTL_SERR << 16;
+		if (advk_readl(pcie, PCIE_CORE_CTRL1_REG) & HOT_RESET_GEN)
+			val |= PCI_BRIDGE_CTL_BUS_RESET << 16;
+		else
+			val &= ~(PCI_BRIDGE_CTL_BUS_RESET << 16);
+		*value = val;
 		return PCI_BRIDGE_EMUL_HANDLED;
 	}
 
-	case PCI_EXP_RTSTA: {
-		u32 isr0 = advk_readl(pcie, PCIE_ISR0_REG);
-		u32 msglog = advk_readl(pcie, PCIE_MSG_LOG_REG);
-		*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16 | (msglog >> 16);
+	default:
+		return PCI_BRIDGE_EMUL_NOT_HANDLED;
+	}
+}
+
+static void
+advk_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,
+				     int reg, u32 old, u32 new, u32 mask)
+{
+	struct advk_pcie *pcie = bridge->data;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		advk_writel(pcie, new, PCIE_CORE_CMD_STATUS_REG);
+		break;
+
+	case PCI_INTERRUPT_LINE:
+		/*
+		 * According to Figure 6-3: Pseudo Logic Diagram for Error
+		 * Message Controls in PCIe base specification, SERR# Enable bit
+		 * in Bridge Control register enable receiving of ERR_* messages
+		 */
+		if (mask & (PCI_BRIDGE_CTL_SERR << 16)) {
+			u32 val = advk_readl(pcie, PCIE_ISR0_MASK_REG);
+			if (new & (PCI_BRIDGE_CTL_SERR << 16))
+				val &= ~PCIE_ISR0_ERR_MASK;
+			else
+				val |= PCIE_ISR0_ERR_MASK;
+			advk_writel(pcie, val, PCIE_ISR0_MASK_REG);
+		}
+		if (mask & (PCI_BRIDGE_CTL_BUS_RESET << 16)) {
+			u32 val = advk_readl(pcie, PCIE_CORE_CTRL1_REG);
+			if (new & (PCI_BRIDGE_CTL_BUS_RESET << 16))
+				val |= HOT_RESET_GEN;
+			else
+				val &= ~HOT_RESET_GEN;
+			advk_writel(pcie, val, PCIE_CORE_CTRL1_REG);
+		}
+		break;
+
+	default:
+		break;
+	}
+}
+
+static pci_bridge_emul_read_status_t
+advk_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
+				    int reg, u32 *value)
+{
+	struct advk_pcie *pcie = bridge->data;
+
+
+	switch (reg) {
+	/*
+	 * PCI_EXP_SLTCAP, PCI_EXP_SLTCTL, PCI_EXP_RTCTL and PCI_EXP_RTSTA are
+	 * also supported, but do not need to be handled here, because their
+	 * values are stored in emulated config space buffer, and we read them
+	 * from there when needed.
+	 */
+
+	case PCI_EXP_LNKCAP: {
+		u32 val = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + reg);
+		/*
+		 * PCI_EXP_LNKCAP_DLLLARC bit is hardwired in aardvark HW to 0.
+		 * But support for PCI_EXP_LNKSTA_DLLLA is emulated via ltssm
+		 * state so explicitly enable PCI_EXP_LNKCAP_DLLLARC flag.
+		 */
+		val |= PCI_EXP_LNKCAP_DLLLARC;
+		*value = val;
 		return PCI_BRIDGE_EMUL_HANDLED;
 	}
 
@@ -738,18 +881,23 @@
 		/* u32 contains both PCI_EXP_LNKCTL and PCI_EXP_LNKSTA */
 		u32 val = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + reg) &
 			~(PCI_EXP_LNKSTA_LT << 16);
-		if (!advk_pcie_link_up(pcie))
+		if (advk_pcie_link_training(pcie))
 			val |= (PCI_EXP_LNKSTA_LT << 16);
+		if (advk_pcie_link_active(pcie))
+			val |= (PCI_EXP_LNKSTA_DLLLA << 16);
 		*value = val;
 		return PCI_BRIDGE_EMUL_HANDLED;
 	}
 
-	case PCI_CAP_LIST_ID:
 	case PCI_EXP_DEVCAP:
 	case PCI_EXP_DEVCTL:
-	case PCI_EXP_LNKCAP:
+	case PCI_EXP_DEVCAP2:
+	case PCI_EXP_DEVCTL2:
+	case PCI_EXP_LNKCAP2:
+	case PCI_EXP_LNKCTL2:
 		*value = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + reg);
 		return PCI_BRIDGE_EMUL_HANDLED;
+
 	default:
 		return PCI_BRIDGE_EMUL_NOT_HANDLED;
 	}
@@ -763,10 +911,6 @@
 	struct advk_pcie *pcie = bridge->data;
 
 	switch (reg) {
-	case PCI_EXP_DEVCTL:
-		advk_writel(pcie, new, PCIE_CORE_PCIEXP_CAP + reg);
-		break;
-
 	case PCI_EXP_LNKCTL:
 		advk_writel(pcie, new, PCIE_CORE_PCIEXP_CAP + reg);
 		if (new & PCI_EXP_LNKCTL_RL)
@@ -774,18 +918,23 @@
 		break;
 
 	case PCI_EXP_RTCTL: {
-		/* Only mask/unmask PME interrupt */
-		u32 val = advk_readl(pcie, PCIE_ISR0_MASK_REG) &
-			~PCIE_MSG_PM_PME_MASK;
-		if ((new & PCI_EXP_RTCTL_PMEIE) == 0)
-			val |= PCIE_MSG_PM_PME_MASK;
-		advk_writel(pcie, val, PCIE_ISR0_MASK_REG);
+		u16 rootctl = le16_to_cpu(bridge->pcie_conf.rootctl);
+		/* Only emulation of PMEIE and CRSSVE bits is provided */
+		rootctl &= PCI_EXP_RTCTL_PMEIE | PCI_EXP_RTCTL_CRSSVE;
+		bridge->pcie_conf.rootctl = cpu_to_le16(rootctl);
 		break;
 	}
 
-	case PCI_EXP_RTSTA:
-		new = (new & PCI_EXP_RTSTA_PME) >> 9;
-		advk_writel(pcie, new, PCIE_ISR0_REG);
+	/*
+	 * PCI_EXP_RTSTA is also supported, but does not need to be handled
+	 * here, because its value is stored in emulated config space buffer,
+	 * and we write it there when needed.
+	 */
+
+	case PCI_EXP_DEVCTL:
+	case PCI_EXP_DEVCTL2:
+	case PCI_EXP_LNKCTL2:
+		advk_writel(pcie, new, PCIE_CORE_PCIEXP_CAP + reg);
 		break;
 
 	default:
@@ -794,6 +943,8 @@
 }
 
 static struct pci_bridge_emul_ops advk_pci_bridge_emul_ops = {
+	.read_base = advk_pci_bridge_emul_base_conf_read,
+	.write_base = advk_pci_bridge_emul_base_conf_write,
 	.read_pcie = advk_pci_bridge_emul_pcie_conf_read,
 	.write_pcie = advk_pci_bridge_emul_pcie_conf_write,
 };
@@ -805,7 +956,6 @@
 static int advk_sw_pci_bridge_init(struct advk_pcie *pcie)
 {
 	struct pci_bridge_emul *bridge = &pcie->bridge;
-	int ret;
 
 	bridge->conf.vendor =
 		cpu_to_le16(advk_readl(pcie, PCIE_CORE_DEV_ID_REG) & 0xffff);
@@ -823,21 +973,36 @@
 	bridge->conf.pref_mem_limit = cpu_to_le16(PCI_PREF_RANGE_TYPE_64);
 
 	/* Support interrupt A for MSI feature */
-	bridge->conf.intpin = PCIE_CORE_INT_A_ASSERT_ENABLE;
+	bridge->conf.intpin = PCI_INTERRUPT_INTA;
 
-	bridge->has_pcie = true;
-	bridge->data = pcie;
-	bridge->ops = &advk_pci_bridge_emul_ops;
+	/*
+	 * Aardvark HW provides PCIe Capability structure in version 2 and
+	 * indicate slot support, which is emulated.
+	 */
+	bridge->pcie_conf.cap = cpu_to_le16(2 | PCI_EXP_FLAGS_SLOT);
 
-	/* PCIe config space can be initialized after pci_bridge_emul_init() */
-	ret = pci_bridge_emul_init(bridge, 0);
-	if (ret < 0)
-		return ret;
+	/*
+	 * Set Presence Detect State bit permanently since there is no support
+	 * for unplugging the card nor detecting whether it is plugged. (If a
+	 * platform exists in the future that supports it, via a GPIO for
+	 * example, it should be implemented via this bit.)
+	 *
+	 * Set physical slot number to 1 since there is only one port and zero
+	 * value is reserved for ports within the same silicon as Root Port
+	 * which is not our case.
+	 */
+	bridge->pcie_conf.slotcap = cpu_to_le32(FIELD_PREP(PCI_EXP_SLTCAP_PSN,
+							   1));
+	bridge->pcie_conf.slotsta = cpu_to_le16(PCI_EXP_SLTSTA_PDS);
 
 	/* Indicates supports for Completion Retry Status */
 	bridge->pcie_conf.rootcap = cpu_to_le16(PCI_EXP_RTCAP_CRSVIS);
 
-	return 0;
+	bridge->has_pcie = true;
+	bridge->data = pcie;
+	bridge->ops = &advk_pci_bridge_emul_ops;
+
+	return pci_bridge_emul_init(bridge, 0);
 }
 
 static bool advk_pcie_valid_device(struct advk_pcie *pcie, struct pci_bus *bus,
@@ -847,8 +1012,12 @@
 		return false;
 
 	/*
-	 * If the link goes down after we check for link-up, nothing bad
-	 * happens but the config access times out.
+	 * If the link goes down after we check for link-up, we have a problem:
+	 * if a PIO request is executed while link-down, the whole controller
+	 * gets stuck in a non-functional state, and even after link comes up
+	 * again, PIO requests won't work anymore, and a reset of the whole PCIe
+	 * controller is needed. Therefore we need to prevent sending PIO
+	 * requests while the link is down.
 	 */
 	if (!pci_is_root_bus(bus) && !advk_pcie_link_up(pcie))
 		return false;
@@ -889,6 +1058,7 @@
 			     int where, int size, u32 *val)
 {
 	struct advk_pcie *pcie = bus->sysdata;
+	int retry_count;
 	bool allow_crs;
 	u32 reg;
 	int ret;
@@ -911,18 +1081,8 @@
 		    (le16_to_cpu(pcie->bridge.pcie_conf.rootctl) &
 		     PCI_EXP_RTCTL_CRSSVE);
 
-	if (advk_pcie_pio_is_running(pcie)) {
-		/*
-		 * If it is possible return Completion Retry Status so caller
-		 * tries to issue the request again instead of failing.
-		 */
-		if (allow_crs) {
-			*val = CFG_RD_CRS_VAL;
-			return PCIBIOS_SUCCESSFUL;
-		}
-		*val = 0xffffffff;
-		return PCIBIOS_SET_FAILED;
-	}
+	if (advk_pcie_pio_is_running(pcie))
+		goto try_crs;
 
 	/* Program the control register */
 	reg = advk_readl(pcie, PIO_CTRL);
@@ -941,30 +1101,24 @@
 	/* Program the data strobe */
 	advk_writel(pcie, 0xf, PIO_WR_DATA_STRB);
 
-	/* Clear PIO DONE ISR and start the transfer */
-	advk_writel(pcie, 1, PIO_ISR);
-	advk_writel(pcie, 1, PIO_START);
-
-	ret = advk_pcie_wait_pio(pcie);
-	if (ret < 0) {
-		/*
-		 * If it is possible return Completion Retry Status so caller
-		 * tries to issue the request again instead of failing.
-		 */
-		if (allow_crs) {
-			*val = CFG_RD_CRS_VAL;
-			return PCIBIOS_SUCCESSFUL;
-		}
-		*val = 0xffffffff;
-		return PCIBIOS_SET_FAILED;
-	}
+	retry_count = 0;
+	do {
+		/* Clear PIO DONE ISR and start the transfer */
+		advk_writel(pcie, 1, PIO_ISR);
+		advk_writel(pcie, 1, PIO_START);
+
+		ret = advk_pcie_wait_pio(pcie);
+		if (ret < 0)
+			goto try_crs;
+
+		retry_count += ret;
+
+		/* Check PIO status and get the read result */
+		ret = advk_pcie_check_pio_status(pcie, allow_crs, val);
+	} while (ret == -EAGAIN && retry_count < PIO_RETRY_CNT);
 
-	/* Check PIO status and get the read result */
-	ret = advk_pcie_check_pio_status(pcie, allow_crs, val);
-	if (ret < 0) {
-		*val = 0xffffffff;
-		return PCIBIOS_SET_FAILED;
-	}
+	if (ret < 0)
+		goto fail;
 
 	if (size == 1)
 		*val = (*val >> (8 * (where & 3))) & 0xff;
@@ -972,6 +1126,20 @@
 		*val = (*val >> (8 * (where & 3))) & 0xffff;
 
 	return PCIBIOS_SUCCESSFUL;
+
+try_crs:
+	/*
+	 * If it is possible, return Completion Retry Status so that caller
+	 * tries to issue the request again instead of failing.
+	 */
+	if (allow_crs) {
+		*val = CFG_RD_CRS_VAL;
+		return PCIBIOS_SUCCESSFUL;
+	}
+
+fail:
+	*val = 0xffffffff;
+	return PCIBIOS_SET_FAILED;
 }
 
 static int advk_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
@@ -980,6 +1148,7 @@
 	struct advk_pcie *pcie = bus->sysdata;
 	u32 reg;
 	u32 data_strobe = 0x0;
+	int retry_count;
 	int offset;
 	int ret;
 
@@ -1021,19 +1190,22 @@
 	/* Program the data strobe */
 	advk_writel(pcie, data_strobe, PIO_WR_DATA_STRB);
 
-	/* Clear PIO DONE ISR and start the transfer */
-	advk_writel(pcie, 1, PIO_ISR);
-	advk_writel(pcie, 1, PIO_START);
+	retry_count = 0;
+	do {
+		/* Clear PIO DONE ISR and start the transfer */
+		advk_writel(pcie, 1, PIO_ISR);
+		advk_writel(pcie, 1, PIO_START);
+
+		ret = advk_pcie_wait_pio(pcie);
+		if (ret < 0)
+			return PCIBIOS_SET_FAILED;
 
-	ret = advk_pcie_wait_pio(pcie);
-	if (ret < 0)
-		return PCIBIOS_SET_FAILED;
+		retry_count += ret;
 
-	ret = advk_pcie_check_pio_status(pcie, false, NULL);
-	if (ret < 0)
-		return PCIBIOS_SET_FAILED;
+		ret = advk_pcie_check_pio_status(pcie, false, NULL);
+	} while (ret == -EAGAIN && retry_count < PIO_RETRY_CNT);
 
-	return PCIBIOS_SUCCESSFUL;
+	return ret < 0 ? PCIBIOS_SET_FAILED : PCIBIOS_SUCCESSFUL;
 }
 
 static struct pci_ops advk_pcie_ops = {
@@ -1045,11 +1217,11 @@
 					 struct msi_msg *msg)
 {
 	struct advk_pcie *pcie = irq_data_get_irq_chip_data(data);
-	phys_addr_t msi_msg = virt_to_phys(&pcie->msi_msg);
+	phys_addr_t msi_addr = virt_to_phys(pcie);
 
-	msg->address_lo = lower_32_bits(msi_msg);
-	msg->address_hi = upper_32_bits(msi_msg);
-	msg->data = data->irq;
+	msg->address_lo = lower_32_bits(msi_addr);
+	msg->address_hi = upper_32_bits(msi_addr);
+	msg->data = data->hwirq;
 }
 
 static int advk_msi_set_affinity(struct irq_data *irq_data,
@@ -1058,6 +1230,54 @@
 	return -EINVAL;
 }
 
+static void advk_msi_irq_mask(struct irq_data *d)
+{
+	struct advk_pcie *pcie = d->domain->host_data;
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	unsigned long flags;
+	u32 mask;
+
+	raw_spin_lock_irqsave(&pcie->msi_irq_lock, flags);
+	mask = advk_readl(pcie, PCIE_MSI_MASK_REG);
+	mask |= BIT(hwirq);
+	advk_writel(pcie, mask, PCIE_MSI_MASK_REG);
+	raw_spin_unlock_irqrestore(&pcie->msi_irq_lock, flags);
+}
+
+static void advk_msi_irq_unmask(struct irq_data *d)
+{
+	struct advk_pcie *pcie = d->domain->host_data;
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	unsigned long flags;
+	u32 mask;
+
+	raw_spin_lock_irqsave(&pcie->msi_irq_lock, flags);
+	mask = advk_readl(pcie, PCIE_MSI_MASK_REG);
+	mask &= ~BIT(hwirq);
+	advk_writel(pcie, mask, PCIE_MSI_MASK_REG);
+	raw_spin_unlock_irqrestore(&pcie->msi_irq_lock, flags);
+}
+
+static void advk_msi_top_irq_mask(struct irq_data *d)
+{
+	pci_msi_mask_irq(d);
+	irq_chip_mask_parent(d);
+}
+
+static void advk_msi_top_irq_unmask(struct irq_data *d)
+{
+	pci_msi_unmask_irq(d);
+	irq_chip_unmask_parent(d);
+}
+
+static struct irq_chip advk_msi_bottom_irq_chip = {
+	.name			= "MSI",
+	.irq_compose_msi_msg	= advk_msi_irq_compose_msi_msg,
+	.irq_set_affinity	= advk_msi_set_affinity,
+	.irq_mask		= advk_msi_irq_mask,
+	.irq_unmask		= advk_msi_irq_unmask,
+};
+
 static int advk_msi_irq_domain_alloc(struct irq_domain *domain,
 				     unsigned int virq,
 				     unsigned int nr_irqs, void *args)
@@ -1066,23 +1286,19 @@
 	int hwirq, i;
 
 	mutex_lock(&pcie->msi_used_lock);
-	hwirq = bitmap_find_next_zero_area(pcie->msi_used, MSI_IRQ_NUM,
-					   0, nr_irqs, 0);
-	if (hwirq >= MSI_IRQ_NUM) {
-		mutex_unlock(&pcie->msi_used_lock);
-		return -ENOSPC;
-	}
-
-	bitmap_set(pcie->msi_used, hwirq, nr_irqs);
+	hwirq = bitmap_find_free_region(pcie->msi_used, MSI_IRQ_NUM,
+					order_base_2(nr_irqs));
 	mutex_unlock(&pcie->msi_used_lock);
+	if (hwirq < 0)
+		return -ENOSPC;
 
 	for (i = 0; i < nr_irqs; i++)
 		irq_domain_set_info(domain, virq + i, hwirq + i,
-				    &pcie->msi_bottom_irq_chip,
+				    &advk_msi_bottom_irq_chip,
 				    domain->host_data, handle_simple_irq,
 				    NULL, NULL);
 
-	return hwirq;
+	return 0;
 }
 
 static void advk_msi_irq_domain_free(struct irq_domain *domain,
@@ -1092,7 +1308,7 @@
 	struct advk_pcie *pcie = domain->host_data;
 
 	mutex_lock(&pcie->msi_used_lock);
-	bitmap_clear(pcie->msi_used, d->hwirq, nr_irqs);
+	bitmap_release_region(pcie->msi_used, d->hwirq, order_base_2(nr_irqs));
 	mutex_unlock(&pcie->msi_used_lock);
 }
 
@@ -1134,7 +1350,6 @@
 {
 	struct advk_pcie *pcie = h->host_data;
 
-	advk_pcie_irq_mask(irq_get_irq_data(virq));
 	irq_set_status_flags(virq, IRQ_LEVEL);
 	irq_set_chip_and_handler(virq, &pcie->irq_chip,
 				 handle_level_irq);
@@ -1148,37 +1363,25 @@
 	.xlate = irq_domain_xlate_onecell,
 };
 
+static struct irq_chip advk_msi_irq_chip = {
+	.name		= "advk-MSI",
+	.irq_mask	= advk_msi_top_irq_mask,
+	.irq_unmask	= advk_msi_top_irq_unmask,
+};
+
+static struct msi_domain_info advk_msi_domain_info = {
+	.flags	= MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
+		  MSI_FLAG_MULTI_PCI_MSI | MSI_FLAG_PCI_MSIX,
+	.chip	= &advk_msi_irq_chip,
+};
+
 static int advk_pcie_init_msi_irq_domain(struct advk_pcie *pcie)
 {
 	struct device *dev = &pcie->pdev->dev;
-	struct device_node *node = dev->of_node;
-	struct irq_chip *bottom_ic, *msi_ic;
-	struct msi_domain_info *msi_di;
-	phys_addr_t msi_msg_phys;
 
+	raw_spin_lock_init(&pcie->msi_irq_lock);
 	mutex_init(&pcie->msi_used_lock);
 
-	bottom_ic = &pcie->msi_bottom_irq_chip;
-
-	bottom_ic->name = "MSI";
-	bottom_ic->irq_compose_msi_msg = advk_msi_irq_compose_msi_msg;
-	bottom_ic->irq_set_affinity = advk_msi_set_affinity;
-
-	msi_ic = &pcie->msi_irq_chip;
-	msi_ic->name = "advk-MSI";
-
-	msi_di = &pcie->msi_domain_info;
-	msi_di->flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
-		MSI_FLAG_MULTI_PCI_MSI;
-	msi_di->chip = msi_ic;
-
-	msi_msg_phys = virt_to_phys(&pcie->msi_msg);
-
-	advk_writel(pcie, lower_32_bits(msi_msg_phys),
-		    PCIE_MSI_ADDR_LOW_REG);
-	advk_writel(pcie, upper_32_bits(msi_msg_phys),
-		    PCIE_MSI_ADDR_HIGH_REG);
-
 	pcie->msi_inner_domain =
 		irq_domain_add_linear(NULL, MSI_IRQ_NUM,
 				      &advk_msi_domain_ops, pcie);
@@ -1186,8 +1389,9 @@
 		return -ENOMEM;
 
 	pcie->msi_domain =
-		pci_msi_create_irq_domain(of_node_to_fwnode(node),
-					  msi_di, pcie->msi_inner_domain);
+		pci_msi_create_irq_domain(dev_fwnode(dev),
+					  &advk_msi_domain_info,
+					  pcie->msi_inner_domain);
 	if (!pcie->msi_domain) {
 		irq_domain_remove(pcie->msi_inner_domain);
 		return -ENOMEM;
@@ -1228,7 +1432,6 @@
 	}
 
 	irq_chip->irq_mask = advk_pcie_irq_mask;
-	irq_chip->irq_mask_ack = advk_pcie_irq_mask;
 	irq_chip->irq_unmask = advk_pcie_irq_unmask;
 
 	pcie->irq_domain =
@@ -1250,22 +1453,85 @@
 	irq_domain_remove(pcie->irq_domain);
 }
 
+static struct irq_chip advk_rp_irq_chip = {
+	.name = "advk-RP",
+};
+
+static int advk_pcie_rp_irq_map(struct irq_domain *h,
+				unsigned int virq, irq_hw_number_t hwirq)
+{
+	struct advk_pcie *pcie = h->host_data;
+
+	irq_set_chip_and_handler(virq, &advk_rp_irq_chip, handle_simple_irq);
+	irq_set_chip_data(virq, pcie);
+
+	return 0;
+}
+
+static const struct irq_domain_ops advk_pcie_rp_irq_domain_ops = {
+	.map = advk_pcie_rp_irq_map,
+	.xlate = irq_domain_xlate_onecell,
+};
+
+static int advk_pcie_init_rp_irq_domain(struct advk_pcie *pcie)
+{
+	pcie->rp_irq_domain = irq_domain_add_linear(NULL, 1,
+						    &advk_pcie_rp_irq_domain_ops,
+						    pcie);
+	if (!pcie->rp_irq_domain) {
+		dev_err(&pcie->pdev->dev, "Failed to add Root Port IRQ domain\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static void advk_pcie_remove_rp_irq_domain(struct advk_pcie *pcie)
+{
+	irq_domain_remove(pcie->rp_irq_domain);
+}
+
+static void advk_pcie_handle_pme(struct advk_pcie *pcie)
+{
+	u32 requester = advk_readl(pcie, PCIE_MSG_LOG_REG) >> 16;
+
+	advk_writel(pcie, PCIE_MSG_PM_PME_MASK, PCIE_ISR0_REG);
+
+	/*
+	 * PCIE_MSG_LOG_REG contains the last inbound message, so store
+	 * the requester ID only when PME was not asserted yet.
+	 * Also do not trigger PME interrupt when PME is still asserted.
+	 */
+	if (!(le32_to_cpu(pcie->bridge.pcie_conf.rootsta) & PCI_EXP_RTSTA_PME)) {
+		pcie->bridge.pcie_conf.rootsta = cpu_to_le32(requester | PCI_EXP_RTSTA_PME);
+
+		/*
+		 * Trigger PME interrupt only if PMEIE bit in Root Control is set.
+		 * Aardvark HW returns zero for PCI_EXP_FLAGS_IRQ, so use PCIe interrupt 0.
+		 */
+		if (!(le16_to_cpu(pcie->bridge.pcie_conf.rootctl) & PCI_EXP_RTCTL_PMEIE))
+			return;
+
+		if (generic_handle_domain_irq(pcie->rp_irq_domain, 0) == -EINVAL)
+			dev_err_ratelimited(&pcie->pdev->dev, "unhandled PME IRQ\n");
+	}
+}
+
 static void advk_pcie_handle_msi(struct advk_pcie *pcie)
 {
 	u32 msi_val, msi_mask, msi_status, msi_idx;
-	u16 msi_data;
 
 	msi_mask = advk_readl(pcie, PCIE_MSI_MASK_REG);
 	msi_val = advk_readl(pcie, PCIE_MSI_STATUS_REG);
-	msi_status = msi_val & ~msi_mask;
+	msi_status = msi_val & ((~msi_mask) & PCIE_MSI_ALL_MASK);
 
 	for (msi_idx = 0; msi_idx < MSI_IRQ_NUM; msi_idx++) {
 		if (!(BIT(msi_idx) & msi_status))
 			continue;
 
 		advk_writel(pcie, BIT(msi_idx), PCIE_MSI_STATUS_REG);
-		msi_data = advk_readl(pcie, PCIE_MSI_PAYLOAD_REG) & 0xFF;
-		generic_handle_irq(msi_data);
+		if (generic_handle_domain_irq(pcie->msi_inner_domain, msi_idx) == -EINVAL)
+			dev_err_ratelimited(&pcie->pdev->dev, "unexpected MSI 0x%02x\n", msi_idx);
 	}
 
 	advk_writel(pcie, PCIE_ISR0_MSI_INT_PENDING,
@@ -1286,10 +1552,20 @@
 	isr1_mask = advk_readl(pcie, PCIE_ISR1_MASK_REG);
 	isr1_status = isr1_val & ((~isr1_mask) & PCIE_ISR1_ALL_MASK);
 
-	if (!isr0_status && !isr1_status) {
-		advk_writel(pcie, isr0_val, PCIE_ISR0_REG);
-		advk_writel(pcie, isr1_val, PCIE_ISR1_REG);
-		return;
+	/* Process PME interrupt as the first one to do not miss PME requester id */
+	if (isr0_status & PCIE_MSG_PM_PME_MASK)
+		advk_pcie_handle_pme(pcie);
+
+	/* Process ERR interrupt */
+	if (isr0_status & PCIE_ISR0_ERR_MASK) {
+		advk_writel(pcie, PCIE_ISR0_ERR_MASK, PCIE_ISR0_REG);
+
+		/*
+		 * Aardvark HW returns zero for PCI_ERR_ROOT_AER_IRQ, so use
+		 * PCIe interrupt 0
+		 */
+		if (generic_handle_domain_irq(pcie->rp_irq_domain, 0) == -EINVAL)
+			dev_err_ratelimited(&pcie->pdev->dev, "unhandled ERR IRQ\n");
 	}
 
 	/* Process MSI interrupts */
@@ -1304,7 +1580,9 @@
 		advk_writel(pcie, PCIE_ISR1_INTX_ASSERT(i),
 			    PCIE_ISR1_REG);
 
-		generic_handle_domain_irq(pcie->irq_domain, i);
+		if (generic_handle_domain_irq(pcie->irq_domain, i) == -EINVAL)
+			dev_err_ratelimited(&pcie->pdev->dev, "unexpected INT%c IRQ\n",
+					    (char)i + 'A');
 	}
 }
 
@@ -1325,7 +1603,22 @@
 	return IRQ_HANDLED;
 }
 
-static void __maybe_unused advk_pcie_disable_phy(struct advk_pcie *pcie)
+static int advk_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	struct advk_pcie *pcie = dev->bus->sysdata;
+
+	/*
+	 * Emulated root bridge has its own emulated irq chip and irq domain.
+	 * Argument pin is the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD) and
+	 * hwirq for irq_create_mapping() is indexed from zero.
+	 */
+	if (pci_is_root_bus(dev->bus))
+		return irq_create_mapping(pcie->rp_irq_domain, pin - 1);
+	else
+		return of_irq_parse_and_map_pci(dev, slot, pin);
+}
+
+static void advk_pcie_disable_phy(struct advk_pcie *pcie)
 {
 	phy_power_off(pcie->phy);
 	phy_exit(pcie->phy);
@@ -1411,8 +1704,7 @@
 		 * only PIO for issuing configuration transfers which does
 		 * not use PCIe window configuration.
 		 */
-		if (type != IORESOURCE_MEM && type != IORESOURCE_MEM_64 &&
-		    type != IORESOURCE_IO)
+		if (type != IORESOURCE_MEM && type != IORESOURCE_IO)
 			continue;
 
 		/*
@@ -1420,8 +1712,7 @@
 		 * configuration is set to transparent memory access so it
 		 * does not need window configuration.
 		 */
-		if ((type == IORESOURCE_MEM || type == IORESOURCE_MEM_64) &&
-		    entry->offset == 0)
+		if (type == IORESOURCE_MEM && entry->offset == 0)
 			continue;
 
 		/*
@@ -1536,11 +1827,21 @@
 		return ret;
 	}
 
+	ret = advk_pcie_init_rp_irq_domain(pcie);
+	if (ret) {
+		dev_err(dev, "Failed to initialize irq\n");
+		advk_pcie_remove_msi_irq_domain(pcie);
+		advk_pcie_remove_irq_domain(pcie);
+		return ret;
+	}
+
 	bridge->sysdata = pcie;
 	bridge->ops = &advk_pcie_ops;
+	bridge->map_irq = advk_pcie_map_irq;
 
 	ret = pci_host_probe(bridge);
 	if (ret < 0) {
+		advk_pcie_remove_rp_irq_domain(pcie);
 		advk_pcie_remove_msi_irq_domain(pcie);
 		advk_pcie_remove_irq_domain(pcie);
 		return ret;
@@ -1553,20 +1854,65 @@
 {
 	struct advk_pcie *pcie = platform_get_drvdata(pdev);
 	struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+	u32 val;
 	int i;
 
+	/* Remove PCI bus with all devices */
 	pci_lock_rescan_remove();
 	pci_stop_root_bus(bridge->bus);
 	pci_remove_root_bus(bridge->bus);
 	pci_unlock_rescan_remove();
 
+	/* Disable Root Bridge I/O space, memory space and bus mastering */
+	val = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
+	val &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	advk_writel(pcie, val, PCIE_CORE_CMD_STATUS_REG);
+
+	/* Disable MSI */
+	val = advk_readl(pcie, PCIE_CORE_CTRL2_REG);
+	val &= ~PCIE_CORE_CTRL2_MSI_ENABLE;
+	advk_writel(pcie, val, PCIE_CORE_CTRL2_REG);
+
+	/* Clear MSI address */
+	advk_writel(pcie, 0, PCIE_MSI_ADDR_LOW_REG);
+	advk_writel(pcie, 0, PCIE_MSI_ADDR_HIGH_REG);
+
+	/* Mask all interrupts */
+	advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_MASK_REG);
+	advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_MASK_REG);
+	advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_MASK_REG);
+	advk_writel(pcie, PCIE_IRQ_ALL_MASK, HOST_CTRL_INT_MASK_REG);
+
+	/* Clear all interrupts */
+	advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_STATUS_REG);
+	advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_REG);
+	advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_REG);
+	advk_writel(pcie, PCIE_IRQ_ALL_MASK, HOST_CTRL_INT_STATUS_REG);
+
+	/* Remove IRQ domains */
+	advk_pcie_remove_rp_irq_domain(pcie);
 	advk_pcie_remove_msi_irq_domain(pcie);
 	advk_pcie_remove_irq_domain(pcie);
 
+	/* Free config space for emulated root bridge */
+	pci_bridge_emul_cleanup(&pcie->bridge);
+
+	/* Assert PERST# signal which prepares PCIe card for power down */
+	if (pcie->reset_gpio)
+		gpiod_set_value_cansleep(pcie->reset_gpio, 1);
+
+	/* Disable link training */
+	val = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+	val &= ~LINK_TRAINING_EN;
+	advk_writel(pcie, val, PCIE_CORE_CTRL0_REG);
+
 	/* Disable outbound address windows mapping */
 	for (i = 0; i < OB_WIN_COUNT; i++)
 		advk_pcie_disable_ob_win(pcie, i);
 
+	/* Disable phy */
+	advk_pcie_disable_phy(pcie);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pci-ftpci100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pci-ftpci100.c
@@ -442,22 +442,12 @@
 	p->dev = dev;
 
 	/* Retrieve and enable optional clocks */
-	clk = devm_clk_get(dev, "PCLK");
+	clk = devm_clk_get_enabled(dev, "PCLK");
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
-	ret = clk_prepare_enable(clk);
-	if (ret) {
-		dev_err(dev, "could not prepare PCLK\n");
-		return ret;
-	}
-	p->bus_clk = devm_clk_get(dev, "PCICLK");
+	p->bus_clk = devm_clk_get_enabled(dev, "PCICLK");
 	if (IS_ERR(p->bus_clk))
 		return PTR_ERR(p->bus_clk);
-	ret = clk_prepare_enable(p->bus_clk);
-	if (ret) {
-		dev_err(dev, "could not prepare PCICLK\n");
-		return ret;
-	}
 
 	p->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(p->base))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pci-hyperv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pci-hyperv.c
@@ -483,7 +483,10 @@
 	struct fwnode_handle *fwnode;
 	/* Protocol version negotiated with the host */
 	enum pci_protocol_version_t protocol_version;
+
+	struct mutex state_lock;
 	enum hv_pcibus_state state;
+
 	struct hv_device *hdev;
 	resource_size_t low_mmio_space;
 	resource_size_t high_mmio_space;
@@ -547,19 +550,10 @@
 	struct hv_pcidev_description func[];
 };
 
-enum hv_pcichild_state {
-	hv_pcichild_init = 0,
-	hv_pcichild_requirements,
-	hv_pcichild_resourced,
-	hv_pcichild_ejecting,
-	hv_pcichild_maximum
-};
-
 struct hv_pci_dev {
 	/* List protected by pci_rescan_remove_lock */
 	struct list_head list_entry;
 	refcount_t refs;
-	enum hv_pcichild_state state;
 	struct pci_slot *pci_slot;
 	struct hv_pcidev_description desc;
 	bool reported_missing;
@@ -713,8 +707,8 @@
 		   PCI_CAPABILITY_LIST) {
 		/* ROM BARs are unimplemented */
 		*val = 0;
-	} else if (where >= PCI_INTERRUPT_LINE && where + size <=
-		   PCI_INTERRUPT_PIN) {
+	} else if ((where >= PCI_INTERRUPT_LINE && where + size <= PCI_INTERRUPT_PIN) ||
+		   (where >= PCI_INTERRUPT_PIN && where + size <= PCI_MIN_GNT)) {
 		/*
 		 * Interrupt Line and Interrupt PIN are hard-wired to zero
 		 * because this front-end only supports message-signaled
@@ -1142,6 +1136,10 @@
 		u8 buffer[sizeof(struct pci_delete_interrupt)];
 	} ctxt;
 
+	if (!int_desc->vector_count) {
+		kfree(int_desc);
+		return;
+	}
 	memset(&ctxt, 0, sizeof(ctxt));
 	int_pkt = (struct pci_delete_interrupt *)&ctxt.pkt.message;
 	int_pkt->message_type.type =
@@ -1204,6 +1202,28 @@
 	pci_msi_mask_irq(data);
 }
 
+static unsigned int hv_msi_get_int_vector(struct irq_data *data)
+{
+	struct irq_cfg *cfg = irqd_cfg(data);
+
+	return cfg->vector;
+}
+
+static int hv_msi_prepare(struct irq_domain *domain, struct device *dev,
+			  int nvec, msi_alloc_info_t *info)
+{
+	int ret = pci_msi_prepare(domain, dev, nvec, info);
+
+	/*
+	 * By using the interrupt remapper in the hypervisor IOMMU, contiguous
+	 * CPU vectors is not needed for multi-MSI
+	 */
+	if (info->type == X86_IRQ_ALLOC_TYPE_PCI_MSI)
+		info->flags &= ~X86_IRQ_ALLOC_CONTIGUOUS_VECTORS;
+
+	return ret;
+}
+
 /**
  * hv_irq_unmask() - "Unmask" the IRQ by setting its current
  * affinity.
@@ -1219,6 +1239,7 @@
 	struct msi_desc *msi_desc = irq_data_get_msi_desc(data);
 	struct irq_cfg *cfg = irqd_cfg(data);
 	struct hv_retarget_device_interrupt *params;
+	struct tran_int_desc *int_desc;
 	struct hv_pcibus_device *hbus;
 	struct cpumask *dest;
 	cpumask_var_t tmp;
@@ -1233,6 +1254,12 @@
 	pdev = msi_desc_to_pci_dev(msi_desc);
 	pbus = pdev->bus;
 	hbus = container_of(pbus->sysdata, struct hv_pcibus_device, sysdata);
+	int_desc = data->chip_data;
+	if (!int_desc) {
+		dev_warn(&hbus->hdev->device, "%s() can not unmask irq %u\n",
+			 __func__, data->irq);
+		return;
+	}
 
 	spin_lock_irqsave(&hbus->retarget_msi_interrupt_lock, flags);
 
@@ -1240,7 +1267,8 @@
 	memset(params, 0, sizeof(*params));
 	params->partition_id = HV_PARTITION_ID_SELF;
 	params->int_entry.source = HV_INTERRUPT_SOURCE_MSI;
-	hv_set_msi_entry_from_desc(&params->int_entry.msi_entry, msi_desc);
+	params->int_entry.msi_entry.address.as_uint32 = int_desc->address & 0xffffffff;
+	params->int_entry.msi_entry.data.as_uint32 = int_desc->data;
 	params->device_id = (hbus->hdev->dev_instance.b[5] << 24) |
 			   (hbus->hdev->dev_instance.b[4] << 16) |
 			   (hbus->hdev->dev_instance.b[7] << 8) |
@@ -1341,12 +1369,12 @@
 
 static u32 hv_compose_msi_req_v1(
 	struct pci_create_interrupt *int_pkt, struct cpumask *affinity,
-	u32 slot, u8 vector)
+	u32 slot, u8 vector, u8 vector_count)
 {
 	int_pkt->message_type.type = PCI_CREATE_INTERRUPT_MESSAGE;
 	int_pkt->wslot.slot = slot;
 	int_pkt->int_desc.vector = vector;
-	int_pkt->int_desc.vector_count = 1;
+	int_pkt->int_desc.vector_count = vector_count;
 	int_pkt->int_desc.delivery_mode = APIC_DELIVERY_MODE_FIXED;
 
 	/*
@@ -1369,14 +1397,14 @@
 
 static u32 hv_compose_msi_req_v2(
 	struct pci_create_interrupt2 *int_pkt, struct cpumask *affinity,
-	u32 slot, u8 vector)
+	u32 slot, u8 vector, u8 vector_count)
 {
 	int cpu;
 
 	int_pkt->message_type.type = PCI_CREATE_INTERRUPT_MESSAGE2;
 	int_pkt->wslot.slot = slot;
 	int_pkt->int_desc.vector = vector;
-	int_pkt->int_desc.vector_count = 1;
+	int_pkt->int_desc.vector_count = vector_count;
 	int_pkt->int_desc.delivery_mode = APIC_DELIVERY_MODE_FIXED;
 	cpu = hv_compose_msi_req_get_cpu(affinity);
 	int_pkt->int_desc.processor_array[0] =
@@ -1388,7 +1416,7 @@
 
 static u32 hv_compose_msi_req_v3(
 	struct pci_create_interrupt3 *int_pkt, struct cpumask *affinity,
-	u32 slot, u32 vector)
+	u32 slot, u32 vector, u8 vector_count)
 {
 	int cpu;
 
@@ -1396,7 +1424,7 @@
 	int_pkt->wslot.slot = slot;
 	int_pkt->int_desc.vector = vector;
 	int_pkt->int_desc.reserved = 0;
-	int_pkt->int_desc.vector_count = 1;
+	int_pkt->int_desc.vector_count = vector_count;
 	int_pkt->int_desc.delivery_mode = APIC_DELIVERY_MODE_FIXED;
 	cpu = hv_compose_msi_req_get_cpu(affinity);
 	int_pkt->int_desc.processor_array[0] =
@@ -1419,7 +1447,6 @@
  */
 static void hv_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
 {
-	struct irq_cfg *cfg = irqd_cfg(data);
 	struct hv_pcibus_device *hbus;
 	struct vmbus_channel *channel;
 	struct hv_pci_dev *hpdev;
@@ -1428,6 +1455,8 @@
 	struct cpumask *dest;
 	struct compose_comp_ctxt comp;
 	struct tran_int_desc *int_desc;
+	struct msi_desc *msi_desc;
+	u8 vector, vector_count;
 	struct {
 		struct pci_packet pci_pkt;
 		union {
@@ -1440,7 +1469,17 @@
 	u32 size;
 	int ret;
 
-	pdev = msi_desc_to_pci_dev(irq_data_get_msi_desc(data));
+	/* Reuse the previous allocation */
+	if (data->chip_data) {
+		int_desc = data->chip_data;
+		msg->address_hi = int_desc->address >> 32;
+		msg->address_lo = int_desc->address & 0xffffffff;
+		msg->data = int_desc->data;
+		return;
+	}
+
+	msi_desc  = irq_data_get_msi_desc(data);
+	pdev = msi_desc_to_pci_dev(msi_desc);
 	dest = irq_data_get_effective_affinity_mask(data);
 	pbus = pdev->bus;
 	hbus = container_of(pbus->sysdata, struct hv_pcibus_device, sysdata);
@@ -1449,17 +1488,40 @@
 	if (!hpdev)
 		goto return_null_message;
 
-	/* Free any previous message that might have already been composed. */
-	if (data->chip_data) {
-		int_desc = data->chip_data;
-		data->chip_data = NULL;
-		hv_int_desc_free(hpdev, int_desc);
-	}
-
 	int_desc = kzalloc(sizeof(*int_desc), GFP_ATOMIC);
 	if (!int_desc)
 		goto drop_reference;
 
+	if (!msi_desc->msi_attrib.is_msix && msi_desc->nvec_used > 1) {
+		/*
+		 * If this is not the first MSI of Multi MSI, we already have
+		 * a mapping.  Can exit early.
+		 */
+		if (msi_desc->irq != data->irq) {
+			data->chip_data = int_desc;
+			int_desc->address = msi_desc->msg.address_lo |
+					    (u64)msi_desc->msg.address_hi << 32;
+			int_desc->data = msi_desc->msg.data +
+					 (data->irq - msi_desc->irq);
+			msg->address_hi = msi_desc->msg.address_hi;
+			msg->address_lo = msi_desc->msg.address_lo;
+			msg->data = int_desc->data;
+			put_pcichild(hpdev);
+			return;
+		}
+		/*
+		 * The vector we select here is a dummy value.  The correct
+		 * value gets sent to the hypervisor in unmask().  This needs
+		 * to be aligned with the count, and also not zero.  Multi-msi
+		 * is powers of 2 up to 32, so 32 will always work here.
+		 */
+		vector = 32;
+		vector_count = msi_desc->nvec_used;
+	} else {
+		vector = hv_msi_get_int_vector(data);
+		vector_count = 1;
+	}
+
 	memset(&ctxt, 0, sizeof(ctxt));
 	init_completion(&comp.comp_pkt.host_event);
 	ctxt.pci_pkt.completion_func = hv_pci_compose_compl;
@@ -1470,7 +1532,8 @@
 		size = hv_compose_msi_req_v1(&ctxt.int_pkts.v1,
 					dest,
 					hpdev->desc.win_slot.slot,
-					cfg->vector);
+					vector,
+					vector_count);
 		break;
 
 	case PCI_PROTOCOL_VERSION_1_2:
@@ -1478,14 +1541,16 @@
 		size = hv_compose_msi_req_v2(&ctxt.int_pkts.v2,
 					dest,
 					hpdev->desc.win_slot.slot,
-					cfg->vector);
+					vector,
+					vector_count);
 		break;
 
 	case PCI_PROTOCOL_VERSION_1_4:
 		size = hv_compose_msi_req_v3(&ctxt.int_pkts.v3,
 					dest,
 					hpdev->desc.win_slot.slot,
-					cfg->vector);
+					vector,
+					vector_count);
 		break;
 
 	default:
@@ -1544,12 +1609,6 @@
 		hv_pci_onchannelcallback(hbus);
 		spin_unlock_irqrestore(&channel->sched_lock, flags);
 
-		if (hpdev->state == hv_pcichild_ejecting) {
-			dev_err_once(&hbus->hdev->device,
-				     "the device is being ejected\n");
-			goto enable_tasklet;
-		}
-
 		udelay(100);
 	}
 
@@ -1601,7 +1660,7 @@
 };
 
 static struct msi_domain_ops hv_msi_ops = {
-	.msi_prepare	= pci_msi_prepare,
+	.msi_prepare	= hv_msi_prepare,
 	.msi_free	= hv_msi_free,
 };
 
@@ -1899,8 +1958,17 @@
 		if (!hv_dev)
 			continue;
 
-		if (hv_dev->desc.flags & HV_PCI_DEVICE_FLAG_NUMA_AFFINITY)
-			set_dev_node(&dev->dev, hv_dev->desc.virtual_numa_node);
+		if (hv_dev->desc.flags & HV_PCI_DEVICE_FLAG_NUMA_AFFINITY &&
+		    hv_dev->desc.virtual_numa_node < num_possible_nodes())
+			/*
+			 * The kernel may boot with some NUMA nodes offline
+			 * (e.g. in a KDUMP kernel) or with NUMA disabled via
+			 * "numa=off". In those cases, adjust the host provided
+			 * NUMA node to a valid NUMA node used by the kernel.
+			 */
+			set_dev_node(&dev->dev,
+				     numa_map_to_online_node(
+					     hv_dev->desc.virtual_numa_node));
 
 		put_pcichild(hv_dev);
 	}
@@ -2126,6 +2194,8 @@
 	if (!dr)
 		return;
 
+	mutex_lock(&hbus->state_lock);
+
 	/* First, mark all existing children as reported missing. */
 	spin_lock_irqsave(&hbus->device_list_lock, flags);
 	list_for_each_entry(hpdev, &hbus->children, list_entry) {
@@ -2207,6 +2277,8 @@
 		break;
 	}
 
+	mutex_unlock(&hbus->state_lock);
+
 	kfree(dr);
 }
 
@@ -2355,7 +2427,7 @@
 	hpdev = container_of(work, struct hv_pci_dev, wrk);
 	hbus = hpdev->hbus;
 
-	WARN_ON(hpdev->state != hv_pcichild_ejecting);
+	mutex_lock(&hbus->state_lock);
 
 	/*
 	 * Ejection can come before or after the PCI bus has been set up, so
@@ -2393,6 +2465,8 @@
 	put_pcichild(hpdev);
 	put_pcichild(hpdev);
 	/* hpdev has been freed. Do not use it any more. */
+
+	mutex_unlock(&hbus->state_lock);
 }
 
 /**
@@ -2413,7 +2487,6 @@
 		return;
 	}
 
-	hpdev->state = hv_pcichild_ejecting;
 	get_pcichild(hpdev);
 	INIT_WORK(&hpdev->wrk, hv_eject_device_work);
 	queue_work(hbus->wq, &hpdev->wrk);
@@ -2814,8 +2887,10 @@
 	struct pci_bus_d0_entry *d0_entry;
 	struct hv_pci_compl comp_pkt;
 	struct pci_packet *pkt;
+	bool retry = true;
 	int ret;
 
+enter_d0_retry:
 	/*
 	 * Tell the host that the bus is ready to use, and moved into the
 	 * powered-on state.  This includes telling the host which region
@@ -2842,6 +2917,38 @@
 	if (ret)
 		goto exit;
 
+	/*
+	 * In certain case (Kdump) the pci device of interest was
+	 * not cleanly shut down and resource is still held on host
+	 * side, the host could return invalid device status.
+	 * We need to explicitly request host to release the resource
+	 * and try to enter D0 again.
+	 */
+	if (comp_pkt.completion_status < 0 && retry) {
+		retry = false;
+
+		dev_err(&hdev->device, "Retrying D0 Entry\n");
+
+		/*
+		 * Hv_pci_bus_exit() calls hv_send_resource_released()
+		 * to free up resources of its child devices.
+		 * In the kdump kernel we need to set the
+		 * wslot_res_allocated to 255 so it scans all child
+		 * devices to release resources allocated in the
+		 * normal kernel before panic happened.
+		 */
+		hbus->wslot_res_allocated = 255;
+
+		ret = hv_pci_bus_exit(hdev, true);
+
+		if (ret == 0) {
+			kfree(pkt);
+			goto enter_d0_retry;
+		}
+		dev_err(&hdev->device,
+			"Retrying D0 failed with ret %d\n", ret);
+	}
+
 	if (comp_pkt.completion_status < 0) {
 		dev_err(&hdev->device,
 			"PCI Pass-through VSP failed D0 Entry with status %x\n",
@@ -2884,6 +2991,24 @@
 	if (!ret)
 		ret = wait_for_response(hdev, &comp);
 
+	/*
+	 * In the case of fast device addition/removal, it's possible that
+	 * vmbus_sendpacket() or wait_for_response() returns -ENODEV but we
+	 * already got a PCI_BUS_RELATIONS* message from the host and the
+	 * channel callback already scheduled a work to hbus->wq, which can be
+	 * running pci_devices_present_work() -> survey_child_resources() ->
+	 * complete(&hbus->survey_event), even after hv_pci_query_relations()
+	 * exits and the stack variable 'comp' is no longer valid; as a result,
+	 * a hang or a page fault may happen when the complete() calls
+	 * raw_spin_lock_irqsave(). Flush hbus->wq before we exit from
+	 * hv_pci_query_relations() to avoid the issues. Note: if 'ret' is
+	 * -ENODEV, there can't be any more work item scheduled to hbus->wq
+	 * after the flush_workqueue(): see vmbus_onoffer_rescind() ->
+	 * vmbus_reset_channel_cb(), vmbus_rescind_cleanup() ->
+	 * channel->rescind = true.
+	 */
+	flush_workqueue(hbus->wq);
+
 	return ret;
 }
 
@@ -3069,7 +3194,6 @@
 	struct hv_pcibus_device *hbus;
 	u16 dom_req, dom;
 	char *name;
-	bool enter_d0_retry = true;
 	int ret;
 
 	/*
@@ -3105,6 +3229,7 @@
 		return -ENOMEM;
 
 	hbus->bridge = bridge;
+	mutex_init(&hbus->state_lock);
 	hbus->state = hv_pcibus_init;
 	hbus->wslot_res_allocated = -1;
 
@@ -3139,6 +3264,15 @@
 	hbus->bridge->domain_nr = dom;
 #ifdef CONFIG_X86
 	hbus->sysdata.domain = dom;
+#elif defined(CONFIG_ARM64)
+	/*
+	 * Set the PCI bus parent to be the corresponding VMbus
+	 * device. Then the VMbus device will be assigned as the
+	 * ACPI companion in pcibios_root_bridge_prepare() and
+	 * pci_dma_configure() will propagate device coherence
+	 * information to devices created on the bus.
+	 */
+	hbus->sysdata.parent = hdev->device.parent;
 #endif
 
 	hbus->hdev = hdev;
@@ -3196,49 +3330,15 @@
 	if (ret)
 		goto free_fwnode;
 
-retry:
 	ret = hv_pci_query_relations(hdev);
 	if (ret)
 		goto free_irq_domain;
 
-	ret = hv_pci_enter_d0(hdev);
-	/*
-	 * In certain case (Kdump) the pci device of interest was
-	 * not cleanly shut down and resource is still held on host
-	 * side, the host could return invalid device status.
-	 * We need to explicitly request host to release the resource
-	 * and try to enter D0 again.
-	 * Since the hv_pci_bus_exit() call releases structures
-	 * of all its child devices, we need to start the retry from
-	 * hv_pci_query_relations() call, requesting host to send
-	 * the synchronous child device relations message before this
-	 * information is needed in hv_send_resources_allocated()
-	 * call later.
-	 */
-	if (ret == -EPROTO && enter_d0_retry) {
-		enter_d0_retry = false;
-
-		dev_err(&hdev->device, "Retrying D0 Entry\n");
-
-		/*
-		 * Hv_pci_bus_exit() calls hv_send_resources_released()
-		 * to free up resources of its child devices.
-		 * In the kdump kernel we need to set the
-		 * wslot_res_allocated to 255 so it scans all child
-		 * devices to release resources allocated in the
-		 * normal kernel before panic happened.
-		 */
-		hbus->wslot_res_allocated = 255;
-		ret = hv_pci_bus_exit(hdev, true);
+	mutex_lock(&hbus->state_lock);
 
-		if (ret == 0)
-			goto retry;
-
-		dev_err(&hdev->device,
-			"Retrying D0 failed with ret %d\n", ret);
-	}
+	ret = hv_pci_enter_d0(hdev);
 	if (ret)
-		goto free_irq_domain;
+		goto release_state_lock;
 
 	ret = hv_pci_allocate_bridge_windows(hbus);
 	if (ret)
@@ -3256,12 +3356,15 @@
 	if (ret)
 		goto free_windows;
 
+	mutex_unlock(&hbus->state_lock);
 	return 0;
 
 free_windows:
 	hv_pci_free_bridge_windows(hbus);
 exit_d0:
 	(void) hv_pci_bus_exit(hdev, true);
+release_state_lock:
+	mutex_unlock(&hbus->state_lock);
 free_irq_domain:
 	irq_domain_remove(hbus->irq_domain);
 free_fwnode:
@@ -3494,20 +3597,26 @@
 	if (ret)
 		goto out;
 
+	mutex_lock(&hbus->state_lock);
+
 	ret = hv_pci_enter_d0(hdev);
 	if (ret)
-		goto out;
+		goto release_state_lock;
 
 	ret = hv_send_resources_allocated(hdev);
 	if (ret)
-		goto out;
+		goto release_state_lock;
 
 	prepopulate_bars(hbus);
 
 	hv_pci_restore_msi_state(hbus);
 
 	hbus->state = hv_pcibus_installed;
+	mutex_unlock(&hbus->state_lock);
 	return 0;
+
+release_state_lock:
+	mutex_unlock(&hbus->state_lock);
 out:
 	vmbus_close(hdev->channel);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pci-loongson.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pci-loongson.c
@@ -13,9 +13,14 @@
 #include "../pci.h"
 
 /* Device IDs */
-#define DEV_PCIE_PORT_0	0x7a09
-#define DEV_PCIE_PORT_1	0x7a19
-#define DEV_PCIE_PORT_2	0x7a29
+#define DEV_LS2K_PCIE_PORT0	0x1a05
+#define DEV_LS7A_PCIE_PORT0	0x7a09
+#define DEV_LS7A_PCIE_PORT1	0x7a19
+#define DEV_LS7A_PCIE_PORT2	0x7a29
+#define DEV_LS7A_PCIE_PORT3	0x7a39
+#define DEV_LS7A_PCIE_PORT4	0x7a49
+#define DEV_LS7A_PCIE_PORT5	0x7a59
+#define DEV_LS7A_PCIE_PORT6	0x7a69
 
 #define DEV_LS2K_APB	0x7a02
 #define DEV_LS7A_CONF	0x7a10
@@ -38,11 +43,11 @@
 	dev->class = PCI_CLASS_BRIDGE_PCI << 8;
 }
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
-			DEV_PCIE_PORT_0, bridge_class_quirk);
+			DEV_LS7A_PCIE_PORT0, bridge_class_quirk);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
-			DEV_PCIE_PORT_1, bridge_class_quirk);
+			DEV_LS7A_PCIE_PORT1, bridge_class_quirk);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
-			DEV_PCIE_PORT_2, bridge_class_quirk);
+			DEV_LS7A_PCIE_PORT2, bridge_class_quirk);
 
 static void system_bus_quirk(struct pci_dev *pdev)
 {
@@ -60,14 +65,27 @@
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
 			DEV_LS7A_LPC, system_bus_quirk);
 
-static void loongson_mrrs_quirk(struct pci_dev *dev)
+/*
+ * Some Loongson PCIe ports have hardware limitations on their Maximum Read
+ * Request Size. They can't handle anything larger than this.  Sane
+ * firmware will set proper MRRS at boot, so we only need no_inc_mrrs for
+ * bridges. However, some MIPS Loongson firmware doesn't set MRRS properly,
+ * so we have to enforce maximum safe MRRS, which is 256 bytes.
+ */
+#ifdef CONFIG_MIPS
+static void loongson_set_min_mrrs_quirk(struct pci_dev *pdev)
 {
-	struct pci_bus *bus = dev->bus;
+	struct pci_bus *bus = pdev->bus;
 	struct pci_dev *bridge;
 	static const struct pci_device_id bridge_devids[] = {
-		{ PCI_VDEVICE(LOONGSON, DEV_PCIE_PORT_0) },
-		{ PCI_VDEVICE(LOONGSON, DEV_PCIE_PORT_1) },
-		{ PCI_VDEVICE(LOONGSON, DEV_PCIE_PORT_2) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS2K_PCIE_PORT0) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT0) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT1) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT2) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT3) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT4) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT5) },
+		{ PCI_VDEVICE(LOONGSON, DEV_LS7A_PCIE_PORT6) },
 		{ 0, },
 	};
 
@@ -75,22 +93,41 @@
 	while (!pci_is_root_bus(bus)) {
 		bridge = bus->self;
 		bus = bus->parent;
-		/*
-		 * Some Loongson PCIe ports have a h/w limitation of
-		 * 256 bytes maximum read request size. They can't handle
-		 * anything larger than this. So force this limit on
-		 * any devices attached under these ports.
-		 */
+
 		if (pci_match_id(bridge_devids, bridge)) {
-			if (pcie_get_readrq(dev) > 256) {
-				pci_info(dev, "limiting MRRS to 256\n");
-				pcie_set_readrq(dev, 256);
+			if (pcie_get_readrq(pdev) > 256) {
+				pci_info(pdev, "limiting MRRS to 256\n");
+				pcie_set_readrq(pdev, 256);
 			}
 			break;
 		}
 	}
 }
-DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, loongson_set_min_mrrs_quirk);
+#endif
+
+static void loongson_mrrs_quirk(struct pci_dev *pdev)
+{
+	struct pci_host_bridge *bridge = pci_find_host_bridge(pdev->bus);
+
+	bridge->no_inc_mrrs = 1;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS2K_PCIE_PORT0, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT0, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT1, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT2, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT3, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT4, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT5, loongson_mrrs_quirk);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LOONGSON,
+			DEV_LS7A_PCIE_PORT6, loongson_mrrs_quirk);
 
 static void __iomem *cfg1_map(struct loongson_pci *priv, int bus,
 				unsigned int devfn, int where)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pci-mvebu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pci-mvebu.c
@@ -51,10 +51,14 @@
 	 PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where) | \
 	 PCIE_CONF_ADDR_EN)
 #define PCIE_CONF_DATA_OFF	0x18fc
+#define PCIE_INT_CAUSE_OFF	0x1900
+#define  PCIE_INT_PM_PME		BIT(28)
 #define PCIE_MASK_OFF		0x1910
 #define  PCIE_MASK_ENABLE_INTS          0x0f000000
 #define PCIE_CTRL_OFF		0x1a00
 #define  PCIE_CTRL_X1_MODE		0x0001
+#define  PCIE_CTRL_RC_MODE		BIT(1)
+#define  PCIE_CTRL_MASTER_HOT_RESET	BIT(24)
 #define PCIE_STAT_OFF		0x1a04
 #define  PCIE_STAT_BUS                  0xff00
 #define  PCIE_STAT_DEV                  0x1f0000
@@ -125,6 +129,11 @@
 	return !(mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_LINK_DOWN);
 }
 
+static u8 mvebu_pcie_get_local_bus_nr(struct mvebu_pcie_port *port)
+{
+	return (mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_BUS) >> 8;
+}
+
 static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie_port *port, int nr)
 {
 	u32 stat;
@@ -213,18 +222,21 @@
 
 static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)
 {
-	u32 cmd, mask;
+	u32 ctrl, cmd, mask;
 
-	/* Point PCIe unit MBUS decode windows to DRAM space. */
-	mvebu_pcie_setup_wins(port);
+	/* Setup PCIe controller to Root Complex mode. */
+	ctrl = mvebu_readl(port, PCIE_CTRL_OFF);
+	ctrl |= PCIE_CTRL_RC_MODE;
+	mvebu_writel(port, ctrl, PCIE_CTRL_OFF);
 
-	/* Master + slave enable. */
+	/* Disable Root Bridge I/O space, memory space and bus mastering. */
 	cmd = mvebu_readl(port, PCIE_CMD_OFF);
-	cmd |= PCI_COMMAND_IO;
-	cmd |= PCI_COMMAND_MEMORY;
-	cmd |= PCI_COMMAND_MASTER;
+	cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
 	mvebu_writel(port, cmd, PCIE_CMD_OFF);
 
+	/* Point PCIe unit MBUS decode windows to DRAM space. */
+	mvebu_pcie_setup_wins(port);
+
 	/* Enable interrupt lines A-D. */
 	mask = mvebu_readl(port, PCIE_MASK_OFF);
 	mask |= PCIE_MASK_ENABLE_INTS;
@@ -371,8 +383,7 @@
 
 	/* Are the new iobase/iolimit values invalid? */
 	if (conf->iolimit < conf->iobase ||
-	    conf->iolimitupper < conf->iobaseupper ||
-	    !(conf->command & PCI_COMMAND_IO)) {
+	    conf->iolimitupper < conf->iobaseupper) {
 		mvebu_pcie_set_window(port, port->io_target, port->io_attr,
 				      &desired, &port->iowin);
 		return;
@@ -409,8 +420,7 @@
 	struct pci_bridge_emul_conf *conf = &port->bridge.conf;
 
 	/* Are the new membase/memlimit values invalid? */
-	if (conf->memlimit < conf->membase ||
-	    !(conf->command & PCI_COMMAND_MEMORY)) {
+	if (conf->memlimit < conf->membase) {
 		mvebu_pcie_set_window(port, port->mem_target, port->mem_attr,
 				      &desired, &port->memwin);
 		return;
@@ -431,6 +441,54 @@
 }
 
 static pci_bridge_emul_read_status_t
+mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,
+				     int reg, u32 *value)
+{
+	struct mvebu_pcie_port *port = bridge->data;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		*value = mvebu_readl(port, PCIE_CMD_OFF);
+		break;
+
+	case PCI_PRIMARY_BUS: {
+		/*
+		 * From the whole 32bit register we support reading from HW only
+		 * secondary bus number which is mvebu local bus number.
+		 * Other bits are retrieved only from emulated config buffer.
+		 */
+		__le32 *cfgspace = (__le32 *)&bridge->conf;
+		u32 val = le32_to_cpu(cfgspace[PCI_PRIMARY_BUS / 4]);
+		val &= ~0xff00;
+		val |= mvebu_pcie_get_local_bus_nr(port) << 8;
+		*value = val;
+		break;
+	}
+
+	case PCI_INTERRUPT_LINE: {
+		/*
+		 * From the whole 32bit register we support reading from HW only
+		 * one bit: PCI_BRIDGE_CTL_BUS_RESET.
+		 * Other bits are retrieved only from emulated config buffer.
+		 */
+		__le32 *cfgspace = (__le32 *)&bridge->conf;
+		u32 val = le32_to_cpu(cfgspace[PCI_INTERRUPT_LINE / 4]);
+		if (mvebu_readl(port, PCIE_CTRL_OFF) & PCIE_CTRL_MASTER_HOT_RESET)
+			val |= PCI_BRIDGE_CTL_BUS_RESET << 16;
+		else
+			val &= ~(PCI_BRIDGE_CTL_BUS_RESET << 16);
+		*value = val;
+		break;
+	}
+
+	default:
+		return PCI_BRIDGE_EMUL_NOT_HANDLED;
+	}
+
+	return PCI_BRIDGE_EMUL_HANDLED;
+}
+
+static pci_bridge_emul_read_status_t
 mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
 				     int reg, u32 *value)
 {
@@ -442,9 +500,7 @@
 		break;
 
 	case PCI_EXP_DEVCTL:
-		*value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL) &
-				 ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE |
-				   PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE);
+		*value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL);
 		break;
 
 	case PCI_EXP_LNKCAP:
@@ -468,6 +524,18 @@
 		*value = mvebu_readl(port, PCIE_RC_RTSTA);
 		break;
 
+	case PCI_EXP_DEVCAP2:
+		*value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCAP2);
+		break;
+
+	case PCI_EXP_DEVCTL2:
+		*value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2);
+		break;
+
+	case PCI_EXP_LNKCTL2:
+		*value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2);
+		break;
+
 	default:
 		return PCI_BRIDGE_EMUL_NOT_HANDLED;
 	}
@@ -484,26 +552,16 @@
 
 	switch (reg) {
 	case PCI_COMMAND:
-	{
-		if (!mvebu_has_ioport(port))
-			conf->command &= ~PCI_COMMAND_IO;
-
-		if ((old ^ new) & PCI_COMMAND_IO)
-			mvebu_pcie_handle_iobase_change(port);
-		if ((old ^ new) & PCI_COMMAND_MEMORY)
-			mvebu_pcie_handle_membase_change(port);
+		if (!mvebu_has_ioport(port)) {
+			conf->command = cpu_to_le16(
+				le16_to_cpu(conf->command) & ~PCI_COMMAND_IO);
+			new &= ~PCI_COMMAND_IO;
+		}
 
+		mvebu_writel(port, new, PCIE_CMD_OFF);
 		break;
-	}
 
 	case PCI_IO_BASE:
-		/*
-		 * We keep bit 1 set, it is a read-only bit that
-		 * indicates we support 32 bits addressing for the
-		 * I/O
-		 */
-		conf->iobase |= PCI_IO_RANGE_TYPE_32;
-		conf->iolimit |= PCI_IO_RANGE_TYPE_32;
 		mvebu_pcie_handle_iobase_change(port);
 		break;
 
@@ -516,7 +574,19 @@
 		break;
 
 	case PCI_PRIMARY_BUS:
-		mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus);
+		if (mask & 0xff00)
+			mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus);
+		break;
+
+	case PCI_INTERRUPT_LINE:
+		if (mask & (PCI_BRIDGE_CTL_BUS_RESET << 16)) {
+			u32 ctrl = mvebu_readl(port, PCIE_CTRL_OFF);
+			if (new & (PCI_BRIDGE_CTL_BUS_RESET << 16))
+				ctrl |= PCIE_CTRL_MASTER_HOT_RESET;
+			else
+				ctrl &= ~PCIE_CTRL_MASTER_HOT_RESET;
+			mvebu_writel(port, ctrl, PCIE_CTRL_OFF);
+		}
 		break;
 
 	default:
@@ -532,13 +602,6 @@
 
 	switch (reg) {
 	case PCI_EXP_DEVCTL:
-		/*
-		 * Armada370 data says these bits must always
-		 * be zero when in root complex mode.
-		 */
-		new &= ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE |
-			 PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE);
-
 		mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL);
 		break;
 
@@ -555,12 +618,31 @@
 		break;
 
 	case PCI_EXP_RTSTA:
-		mvebu_writel(port, new, PCIE_RC_RTSTA);
+		/*
+		 * PME Status bit in Root Status Register (PCIE_RC_RTSTA)
+		 * is read-only and can be cleared only by writing 0b to the
+		 * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So
+		 * clear PME via Interrupt Cause.
+		 */
+		if (new & PCI_EXP_RTSTA_PME)
+			mvebu_writel(port, ~PCIE_INT_PM_PME, PCIE_INT_CAUSE_OFF);
+		break;
+
+	case PCI_EXP_DEVCTL2:
+		mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2);
+		break;
+
+	case PCI_EXP_LNKCTL2:
+		mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2);
+		break;
+
+	default:
 		break;
 	}
 }
 
 static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = {
+	.read_base = mvebu_pci_bridge_emul_base_conf_read,
 	.write_base = mvebu_pci_bridge_emul_base_conf_write,
 	.read_pcie = mvebu_pci_bridge_emul_pcie_conf_read,
 	.write_pcie = mvebu_pci_bridge_emul_pcie_conf_write,
@@ -570,9 +652,11 @@
  * Initialize the configuration space of the PCI-to-PCI bridge
  * associated with the given PCIe interface.
  */
-static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
+static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
 {
 	struct pci_bridge_emul *bridge = &port->bridge;
+	u32 pcie_cap = mvebu_readl(port, PCIE_CAP_PCIEXP);
+	u8 pcie_cap_ver = ((pcie_cap >> 16) & PCI_EXP_FLAGS_VERS);
 
 	bridge->conf.vendor = PCI_VENDOR_ID_MARVELL;
 	bridge->conf.device = mvebu_readl(port, PCIE_DEV_ID_OFF) >> 16;
@@ -585,11 +669,17 @@
 		bridge->conf.iolimit = PCI_IO_RANGE_TYPE_32;
 	}
 
+	/*
+	 * Older mvebu hardware provides PCIe Capability structure only in
+	 * version 1. New hardware provides it in version 2.
+	 */
+	bridge->pcie_conf.cap = cpu_to_le16(pcie_cap_ver);
+
 	bridge->has_pcie = true;
 	bridge->data = port;
 	bridge->ops = &mvebu_pci_bridge_emul_ops;
 
-	pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR);
+	return pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR);
 }
 
 static inline struct mvebu_pcie *sys_to_pcie(struct pci_sys_data *sys)
@@ -1112,9 +1202,94 @@
 			continue;
 		}
 
+		ret = mvebu_pci_bridge_emul_init(port);
+		if (ret < 0) {
+			dev_err(dev, "%s: cannot init emulated bridge\n",
+				port->name);
+			devm_iounmap(dev, port->base);
+			port->base = NULL;
+			mvebu_pcie_powerdown(port);
+			continue;
+		}
+
+		/*
+		 * PCIe topology exported by mvebu hw is quite complicated. In
+		 * reality has something like N fully independent host bridges
+		 * where each host bridge has one PCIe Root Port (which acts as
+		 * PCI Bridge device). Each host bridge has its own independent
+		 * internal registers, independent access to PCI config space,
+		 * independent interrupt lines, independent window and memory
+		 * access configuration. But additionally there is some kind of
+		 * peer-to-peer support between PCIe devices behind different
+		 * host bridges limited just to forwarding of memory and I/O
+		 * transactions (forwarding of error messages and config cycles
+		 * is not supported). So we could say there are N independent
+		 * PCIe Root Complexes.
+		 *
+		 * For this kind of setup DT should have been structured into
+		 * N independent PCIe controllers / host bridges. But instead
+		 * structure in past was defined to put PCIe Root Ports of all
+		 * host bridges into one bus zero, like in classic multi-port
+		 * Root Complex setup with just one host bridge.
+		 *
+		 * This means that pci-mvebu.c driver provides "virtual" bus 0
+		 * on which registers all PCIe Root Ports (PCI Bridge devices)
+		 * specified in DT by their BDF addresses and virtually routes
+		 * PCI config access of each PCI bridge device to specific PCIe
+		 * host bridge.
+		 *
+		 * Normally PCI Bridge should choose between Type 0 and Type 1
+		 * config requests based on primary and secondary bus numbers
+		 * configured on the bridge itself. But because mvebu PCI Bridge
+		 * does not have registers for primary and secondary bus numbers
+		 * in its config space, it determinates type of config requests
+		 * via its own custom way.
+		 *
+		 * There are two options how mvebu determinate type of config
+		 * request.
+		 *
+		 * 1. If Secondary Bus Number Enable bit is not set or is not
+		 * available (applies for pre-XP PCIe controllers) then Type 0
+		 * is used if target bus number equals Local Bus Number (bits
+		 * [15:8] in register 0x1a04) and target device number differs
+		 * from Local Device Number (bits [20:16] in register 0x1a04).
+		 * Type 1 is used if target bus number differs from Local Bus
+		 * Number. And when target bus number equals Local Bus Number
+		 * and target device equals Local Device Number then request is
+		 * routed to Local PCI Bridge (PCIe Root Port).
+		 *
+		 * 2. If Secondary Bus Number Enable bit is set (bit 7 in
+		 * register 0x1a2c) then mvebu hw determinate type of config
+		 * request like compliant PCI Bridge based on primary bus number
+		 * which is configured via Local Bus Number (bits [15:8] in
+		 * register 0x1a04) and secondary bus number which is configured
+		 * via Secondary Bus Number (bits [7:0] in register 0x1a2c).
+		 * Local PCI Bridge (PCIe Root Port) is available on primary bus
+		 * as device with Local Device Number (bits [20:16] in register
+		 * 0x1a04).
+		 *
+		 * Secondary Bus Number Enable bit is disabled by default and
+		 * option 2. is not available on pre-XP PCIe controllers. Hence
+		 * this driver always use option 1.
+		 *
+		 * Basically it means that primary and secondary buses shares
+		 * one virtual number configured via Local Bus Number bits and
+		 * Local Device Number bits determinates if accessing primary
+		 * or secondary bus. Set Local Device Number to 1 and redirect
+		 * all writes of PCI Bridge Secondary Bus Number register to
+		 * Local Bus Number (bits [15:8] in register 0x1a04).
+		 *
+		 * So when accessing devices on buses behind secondary bus
+		 * number it would work correctly. And also when accessing
+		 * device 0 at secondary bus number via config space would be
+		 * correctly routed to secondary bus. Due to issues described
+		 * in mvebu_pcie_setup_hw(), PCI Bridges at primary bus (zero)
+		 * are not accessed directly via PCI config space but rarher
+		 * indirectly via kernel emulated PCI bridge driver.
+		 */
 		mvebu_pcie_setup_hw(port);
 		mvebu_pcie_set_local_dev_nr(port, 1);
-		mvebu_pci_bridge_emul_init(port);
+		mvebu_pcie_set_local_bus_nr(port, 0);
 	}
 
 	pcie->nports = i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pci-xgene.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pci-xgene.c
@@ -480,28 +480,27 @@
 }
 
 static void xgene_pcie_setup_ib_reg(struct xgene_pcie_port *port,
-				    struct resource_entry *entry,
-				    u8 *ib_reg_mask)
+				    struct of_pci_range *range, u8 *ib_reg_mask)
 {
 	void __iomem *cfg_base = port->cfg_base;
 	struct device *dev = port->dev;
 	void __iomem *bar_addr;
 	u32 pim_reg;
-	u64 cpu_addr = entry->res->start;
-	u64 pci_addr = cpu_addr - entry->offset;
-	u64 size = resource_size(entry->res);
+	u64 cpu_addr = range->cpu_addr;
+	u64 pci_addr = range->pci_addr;
+	u64 size = range->size;
 	u64 mask = ~(size - 1) | EN_REG;
 	u32 flags = PCI_BASE_ADDRESS_MEM_TYPE_64;
 	u32 bar_low;
 	int region;
 
-	region = xgene_pcie_select_ib_reg(ib_reg_mask, size);
+	region = xgene_pcie_select_ib_reg(ib_reg_mask, range->size);
 	if (region < 0) {
 		dev_warn(dev, "invalid pcie dma-range config\n");
 		return;
 	}
 
-	if (entry->res->flags & IORESOURCE_PREFETCH)
+	if (range->flags & IORESOURCE_PREFETCH)
 		flags |= PCI_BASE_ADDRESS_MEM_PREFETCH;
 
 	bar_low = pcie_bar_low_val((u32)cpu_addr, flags);
@@ -532,13 +531,25 @@
 
 static int xgene_pcie_parse_map_dma_ranges(struct xgene_pcie_port *port)
 {
-	struct pci_host_bridge *bridge = pci_host_bridge_from_priv(port);
-	struct resource_entry *entry;
+	struct device_node *np = port->node;
+	struct of_pci_range range;
+	struct of_pci_range_parser parser;
+	struct device *dev = port->dev;
 	u8 ib_reg_mask = 0;
 
-	resource_list_for_each_entry(entry, &bridge->dma_ranges)
-		xgene_pcie_setup_ib_reg(port, entry, &ib_reg_mask);
+	if (of_pci_dma_range_parser_init(&parser, np)) {
+		dev_err(dev, "missing dma-ranges property\n");
+		return -EINVAL;
+	}
 
+	/* Get the dma-ranges from DT */
+	for_each_of_pci_range(&parser, &range) {
+		u64 end = range.cpu_addr + range.size - 1;
+
+		dev_dbg(dev, "0x%08x 0x%016llx..0x%016llx -> 0x%016llx\n",
+			range.flags, range.cpu_addr, end, range.pci_addr);
+		xgene_pcie_setup_ib_reg(port, &range, &ib_reg_mask);
+	}
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-brcmstb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-brcmstb.c
@@ -410,10 +410,10 @@
 static void brcm_pcie_set_gen(struct brcm_pcie *pcie, int gen)
 {
 	u16 lnkctl2 = readw(pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2);
-	u32 lnkcap = readl(pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCAP);
+	u32 lnkcap = readl(pcie->base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
 
 	lnkcap = (lnkcap & ~PCI_EXP_LNKCAP_SLS) | gen;
-	writel(lnkcap, pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCAP);
+	writel(lnkcap, pcie->base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
 
 	lnkctl2 = (lnkctl2 & ~0xf) | gen;
 	writew(lnkctl2, pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-mediatek-gen3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -79,6 +79,9 @@
 #define PCIE_ICMD_PM_REG		0x198
 #define PCIE_TURN_OFF_LINK		BIT(4)
 
+#define PCIE_MISC_CTRL_REG		0x348
+#define PCIE_DISABLE_DVFSRC_VLT_REQ	BIT(1)
+
 #define PCIE_TRANS_TABLE_BASE_REG	0x800
 #define PCIE_ATR_SRC_ADDR_MSB_OFFSET	0x4
 #define PCIE_ATR_TRSL_ADDR_LSB_OFFSET	0x8
@@ -297,6 +300,11 @@
 	val &= ~PCIE_INTX_ENABLE;
 	writel_relaxed(val, port->base + PCIE_INT_ENABLE_REG);
 
+	/* Disable DVFSRC voltage request */
+	val = readl_relaxed(port->base + PCIE_MISC_CTRL_REG);
+	val |= PCIE_DISABLE_DVFSRC_VLT_REQ;
+	writel_relaxed(val, port->base + PCIE_MISC_CTRL_REG);
+
 	/* Assert all reset signals */
 	val = readl_relaxed(port->base + PCIE_RST_CTRL_REG);
 	val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB | PCIE_PE_RSTB;
@@ -592,7 +600,8 @@
 						  &intx_domain_ops, port);
 	if (!port->intx_domain) {
 		dev_err(dev, "failed to create INTx IRQ domain\n");
-		return -ENODEV;
+		ret = -ENODEV;
+		goto out_put_node;
 	}
 
 	/* Setup MSI */
@@ -615,6 +624,7 @@
 		goto err_msi_domain;
 	}
 
+	of_node_put(intc_node);
 	return 0;
 
 err_msi_domain:
@@ -622,6 +632,8 @@
 err_msi_bottom_domain:
 	irq_domain_remove(port->intx_domain);
 
+out_put_node:
+	of_node_put(intc_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-mediatek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-mediatek.c
@@ -624,12 +624,18 @@
 		if (status & MSI_STATUS){
 			unsigned long imsi_status;
 
+			/*
+			 * The interrupt status can be cleared even if the
+			 * MSI status remains pending. As such, given the
+			 * edge-triggered interrupt type, its status should
+			 * be cleared before being dispatched to the
+			 * handler of the underlying device.
+			 */
+			writel(MSI_STATUS, port->base + PCIE_INT_STATUS);
 			while ((imsi_status = readl(port->base + PCIE_IMSI_STATUS))) {
 				for_each_set_bit(bit, &imsi_status, MTK_MSI_IRQS_NUM)
 					generic_handle_domain_irq(port->inner_domain, bit);
 			}
-			/* Clear MSI interrupt status */
-			writel(MSI_STATUS, port->base + PCIE_INT_STATUS);
 		}
 	}
 
@@ -1008,6 +1014,7 @@
 					   "mediatek,generic-pciecfg");
 	if (cfg_node) {
 		pcie->cfg = syscon_node_to_regmap(cfg_node);
+		of_node_put(cfg_node);
 		if (IS_ERR(pcie->cfg))
 			return PTR_ERR(pcie->cfg);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-microchip-host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-microchip-host.c
@@ -167,12 +167,12 @@
 #define EVENT_PCIE_DLUP_EXIT			2
 #define EVENT_SEC_TX_RAM_SEC_ERR		3
 #define EVENT_SEC_RX_RAM_SEC_ERR		4
-#define EVENT_SEC_AXI2PCIE_RAM_SEC_ERR		5
-#define EVENT_SEC_PCIE2AXI_RAM_SEC_ERR		6
+#define EVENT_SEC_PCIE2AXI_RAM_SEC_ERR		5
+#define EVENT_SEC_AXI2PCIE_RAM_SEC_ERR		6
 #define EVENT_DED_TX_RAM_DED_ERR		7
 #define EVENT_DED_RX_RAM_DED_ERR		8
-#define EVENT_DED_AXI2PCIE_RAM_DED_ERR		9
-#define EVENT_DED_PCIE2AXI_RAM_DED_ERR		10
+#define EVENT_DED_PCIE2AXI_RAM_DED_ERR		9
+#define EVENT_DED_AXI2PCIE_RAM_DED_ERR		10
 #define EVENT_LOCAL_DMA_END_ENGINE_0		11
 #define EVENT_LOCAL_DMA_END_ENGINE_1		12
 #define EVENT_LOCAL_DMA_ERROR_ENGINE_0		13
@@ -416,6 +416,7 @@
 
 	status = readl_relaxed(bridge_base_addr + ISTATUS_LOCAL);
 	if (status & PM_MSI_INT_MSI_MASK) {
+		writel_relaxed(status & PM_MSI_INT_MSI_MASK, bridge_base_addr + ISTATUS_LOCAL);
 		status = readl_relaxed(bridge_base_addr + ISTATUS_MSI);
 		for_each_set_bit(bit, &status, msi->num_vectors) {
 			ret = generic_handle_domain_irq(msi->dev_domain, bit);
@@ -432,13 +433,8 @@
 	void __iomem *bridge_base_addr =
 		port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
 	u32 bitpos = data->hwirq;
-	unsigned long status;
 
 	writel_relaxed(BIT(bitpos), bridge_base_addr + ISTATUS_MSI);
-	status = readl_relaxed(bridge_base_addr + ISTATUS_MSI);
-	if (!status)
-		writel_relaxed(BIT(PM_MSI_INT_MSI_SHIFT),
-			       bridge_base_addr + ISTATUS_LOCAL);
 }
 
 static void mc_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
@@ -898,6 +894,7 @@
 						   &event_domain_ops, port);
 	if (!port->event_domain) {
 		dev_err(dev, "failed to get event domain\n");
+		of_node_put(pcie_intc_node);
 		return -ENOMEM;
 	}
 
@@ -907,6 +904,7 @@
 						  &intx_domain_ops, port);
 	if (!port->intx_domain) {
 		dev_err(dev, "failed to get an INTx IRQ domain\n");
+		of_node_put(pcie_intc_node);
 		return -ENOMEM;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-rcar-ep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-rcar-ep.c
@@ -110,7 +110,7 @@
 		}
 		if (!devm_request_mem_region(&pdev->dev, res->start,
 					     resource_size(res),
-					     outbound_name)) {
+					     res->name)) {
 			dev_err(pcie->dev, "Cannot request memory region %s.\n",
 				outbound_name);
 			return -EIO;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-rcar-host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-rcar-host.c
@@ -52,10 +52,10 @@
  */
 static void __iomem *pcie_base;
 /*
- * Static copy of bus clock pointer, so we can check whether the clock
- * is enabled or not.
+ * Static copy of PCIe device pointer, so we can check whether the
+ * device is runtime suspended or not.
  */
-static struct clk *pcie_bus_clk;
+static struct device *pcie_dev;
 #endif
 
 /* Structure representing the PCIe interface */
@@ -794,7 +794,7 @@
 #ifdef CONFIG_ARM
 	/* Cache static copy for L1 link state fixup hook on aarch32 */
 	pcie_base = pcie->base;
-	pcie_bus_clk = host->bus_clk;
+	pcie_dev = pcie->dev;
 #endif
 
 	return 0;
@@ -1064,7 +1064,7 @@
 
 	spin_lock_irqsave(&pmsr_lock, flags);
 
-	if (!pcie_base || !__clk_is_enabled(pcie_bus_clk)) {
+	if (!pcie_base || pm_runtime_suspended(pcie_dev)) {
 		ret = 1;
 		goto unlock_exit;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-rockchip-ep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-rockchip-ep.c
@@ -61,84 +61,61 @@
 			    ROCKCHIP_PCIE_AT_OB_REGION_DESC0(region));
 	rockchip_pcie_write(rockchip, 0,
 			    ROCKCHIP_PCIE_AT_OB_REGION_DESC1(region));
-	rockchip_pcie_write(rockchip, 0,
-			    ROCKCHIP_PCIE_AT_OB_REGION_CPU_ADDR0(region));
-	rockchip_pcie_write(rockchip, 0,
-			    ROCKCHIP_PCIE_AT_OB_REGION_CPU_ADDR1(region));
+}
+
+static int rockchip_pcie_ep_ob_atu_num_bits(struct rockchip_pcie *rockchip,
+					    u64 pci_addr, size_t size)
+{
+	int num_pass_bits = fls64(pci_addr ^ (pci_addr + size - 1));
+
+	return clamp(num_pass_bits,
+		     ROCKCHIP_PCIE_AT_MIN_NUM_BITS,
+		     ROCKCHIP_PCIE_AT_MAX_NUM_BITS);
 }
 
 static void rockchip_pcie_prog_ep_ob_atu(struct rockchip_pcie *rockchip, u8 fn,
-					 u32 r, u32 type, u64 cpu_addr,
-					 u64 pci_addr, size_t size)
+					 u32 r, u64 cpu_addr, u64 pci_addr,
+					 size_t size)
 {
-	u64 sz = 1ULL << fls64(size - 1);
-	int num_pass_bits = ilog2(sz);
-	u32 addr0, addr1, desc0, desc1;
-	bool is_nor_msg = (type == AXI_WRAPPER_NOR_MSG);
-
-	/* The minimal region size is 1MB */
-	if (num_pass_bits < 8)
-		num_pass_bits = 8;
-
-	cpu_addr -= rockchip->mem_res->start;
-	addr0 = ((is_nor_msg ? 0x10 : (num_pass_bits - 1)) &
-		PCIE_CORE_OB_REGION_ADDR0_NUM_BITS) |
-		(lower_32_bits(cpu_addr) & PCIE_CORE_OB_REGION_ADDR0_LO_ADDR);
-	addr1 = upper_32_bits(is_nor_msg ? cpu_addr : pci_addr);
-	desc0 = ROCKCHIP_PCIE_AT_OB_REGION_DESC0_DEVFN(fn) | type;
-	desc1 = 0;
-
-	if (is_nor_msg) {
-		rockchip_pcie_write(rockchip, 0,
-				    ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0(r));
-		rockchip_pcie_write(rockchip, 0,
-				    ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR1(r));
-		rockchip_pcie_write(rockchip, desc0,
-				    ROCKCHIP_PCIE_AT_OB_REGION_DESC0(r));
-		rockchip_pcie_write(rockchip, desc1,
-				    ROCKCHIP_PCIE_AT_OB_REGION_DESC1(r));
-	} else {
-		/* PCI bus address region */
-		rockchip_pcie_write(rockchip, addr0,
-				    ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0(r));
-		rockchip_pcie_write(rockchip, addr1,
-				    ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR1(r));
-		rockchip_pcie_write(rockchip, desc0,
-				    ROCKCHIP_PCIE_AT_OB_REGION_DESC0(r));
-		rockchip_pcie_write(rockchip, desc1,
-				    ROCKCHIP_PCIE_AT_OB_REGION_DESC1(r));
-
-		addr0 =
-		    ((num_pass_bits - 1) & PCIE_CORE_OB_REGION_ADDR0_NUM_BITS) |
-		    (lower_32_bits(cpu_addr) &
-		     PCIE_CORE_OB_REGION_ADDR0_LO_ADDR);
-		addr1 = upper_32_bits(cpu_addr);
-	}
+	int num_pass_bits;
+	u32 addr0, addr1, desc0;
+
+	num_pass_bits = rockchip_pcie_ep_ob_atu_num_bits(rockchip,
+							 pci_addr, size);
+
+	addr0 = ((num_pass_bits - 1) & PCIE_CORE_OB_REGION_ADDR0_NUM_BITS) |
+		(lower_32_bits(pci_addr) & PCIE_CORE_OB_REGION_ADDR0_LO_ADDR);
+	addr1 = upper_32_bits(pci_addr);
+	desc0 = ROCKCHIP_PCIE_AT_OB_REGION_DESC0_DEVFN(fn) | AXI_WRAPPER_MEM_WRITE;
 
-	/* CPU bus address region */
+	/* PCI bus address region */
 	rockchip_pcie_write(rockchip, addr0,
-			    ROCKCHIP_PCIE_AT_OB_REGION_CPU_ADDR0(r));
+			    ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0(r));
 	rockchip_pcie_write(rockchip, addr1,
-			    ROCKCHIP_PCIE_AT_OB_REGION_CPU_ADDR1(r));
+			    ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR1(r));
+	rockchip_pcie_write(rockchip, desc0,
+			    ROCKCHIP_PCIE_AT_OB_REGION_DESC0(r));
+	rockchip_pcie_write(rockchip, 0,
+			    ROCKCHIP_PCIE_AT_OB_REGION_DESC1(r));
 }
 
 static int rockchip_pcie_ep_write_header(struct pci_epc *epc, u8 fn, u8 vfn,
 					 struct pci_epf_header *hdr)
 {
+	u32 reg;
 	struct rockchip_pcie_ep *ep = epc_get_drvdata(epc);
 	struct rockchip_pcie *rockchip = &ep->rockchip;
 
 	/* All functions share the same vendor ID with function 0 */
 	if (fn == 0) {
-		u32 vid_regs = (hdr->vendorid & GENMASK(15, 0)) |
-			       (hdr->subsys_vendor_id & GENMASK(31, 16)) << 16;
-
-		rockchip_pcie_write(rockchip, vid_regs,
+		rockchip_pcie_write(rockchip,
+				    hdr->vendorid | hdr->subsys_vendor_id << 16,
 				    PCIE_CORE_CONFIG_VENDOR);
 	}
 
-	rockchip_pcie_write(rockchip, hdr->deviceid << 16,
-			    ROCKCHIP_PCIE_EP_FUNC_BASE(fn) + PCI_VENDOR_ID);
+	reg = rockchip_pcie_read(rockchip, PCIE_EP_CONFIG_DID_VID);
+	reg = (reg & 0xFFFF) | (hdr->deviceid << 16);
+	rockchip_pcie_write(rockchip, reg, PCIE_EP_CONFIG_DID_VID);
 
 	rockchip_pcie_write(rockchip,
 			    hdr->revid |
@@ -256,27 +233,20 @@
 			    ROCKCHIP_PCIE_AT_IB_EP_FUNC_BAR_ADDR1(fn, bar));
 }
 
+static inline u32 rockchip_ob_region(phys_addr_t addr)
+{
+	return (addr >> ilog2(SZ_1M)) & 0x1f;
+}
+
 static int rockchip_pcie_ep_map_addr(struct pci_epc *epc, u8 fn, u8 vfn,
 				     phys_addr_t addr, u64 pci_addr,
 				     size_t size)
 {
 	struct rockchip_pcie_ep *ep = epc_get_drvdata(epc);
 	struct rockchip_pcie *pcie = &ep->rockchip;
-	u32 r;
+	u32 r = rockchip_ob_region(addr);
 
-	r = find_first_zero_bit(&ep->ob_region_map,
-				sizeof(ep->ob_region_map) * BITS_PER_LONG);
-	/*
-	 * Region 0 is reserved for configuration space and shouldn't
-	 * be used elsewhere per TRM, so leave it out.
-	 */
-	if (r >= ep->max_regions - 1) {
-		dev_err(&epc->dev, "no free outbound region\n");
-		return -EINVAL;
-	}
-
-	rockchip_pcie_prog_ep_ob_atu(pcie, fn, r, AXI_WRAPPER_MEM_WRITE, addr,
-				     pci_addr, size);
+	rockchip_pcie_prog_ep_ob_atu(pcie, fn, r, addr, pci_addr, size);
 
 	set_bit(r, &ep->ob_region_map);
 	ep->ob_addr[r] = addr;
@@ -291,15 +261,11 @@
 	struct rockchip_pcie *rockchip = &ep->rockchip;
 	u32 r;
 
-	for (r = 0; r < ep->max_regions - 1; r++)
+	for (r = 0; r < ep->max_regions; r++)
 		if (ep->ob_addr[r] == addr)
 			break;
 
-	/*
-	 * Region 0 is reserved for configuration space and shouldn't
-	 * be used elsewhere per TRM, so leave it out.
-	 */
-	if (r == ep->max_regions - 1)
+	if (r == ep->max_regions)
 		return;
 
 	rockchip_pcie_clear_ep_ob_atu(rockchip, r);
@@ -313,15 +279,15 @@
 {
 	struct rockchip_pcie_ep *ep = epc_get_drvdata(epc);
 	struct rockchip_pcie *rockchip = &ep->rockchip;
-	u16 flags;
+	u32 flags;
 
 	flags = rockchip_pcie_read(rockchip,
 				   ROCKCHIP_PCIE_EP_FUNC_BASE(fn) +
 				   ROCKCHIP_PCIE_EP_MSI_CTRL_REG);
 	flags &= ~ROCKCHIP_PCIE_EP_MSI_CTRL_MMC_MASK;
 	flags |=
-	   ((multi_msg_cap << 1) <<  ROCKCHIP_PCIE_EP_MSI_CTRL_MMC_OFFSET) |
-	   PCI_MSI_FLAGS_64BIT;
+	   (multi_msg_cap << ROCKCHIP_PCIE_EP_MSI_CTRL_MMC_OFFSET) |
+	   (PCI_MSI_FLAGS_64BIT << ROCKCHIP_PCIE_EP_MSI_FLAGS_OFFSET);
 	flags &= ~ROCKCHIP_PCIE_EP_MSI_CTRL_MASK_MSI_CAP;
 	rockchip_pcie_write(rockchip, flags,
 			    ROCKCHIP_PCIE_EP_FUNC_BASE(fn) +
@@ -333,7 +299,7 @@
 {
 	struct rockchip_pcie_ep *ep = epc_get_drvdata(epc);
 	struct rockchip_pcie *rockchip = &ep->rockchip;
-	u16 flags;
+	u32 flags;
 
 	flags = rockchip_pcie_read(rockchip,
 				   ROCKCHIP_PCIE_EP_FUNC_BASE(fn) +
@@ -346,48 +312,25 @@
 }
 
 static void rockchip_pcie_ep_assert_intx(struct rockchip_pcie_ep *ep, u8 fn,
-					 u8 intx, bool is_asserted)
+					 u8 intx, bool do_assert)
 {
 	struct rockchip_pcie *rockchip = &ep->rockchip;
-	u32 r = ep->max_regions - 1;
-	u32 offset;
-	u32 status;
-	u8 msg_code;
-
-	if (unlikely(ep->irq_pci_addr != ROCKCHIP_PCIE_EP_PCI_LEGACY_IRQ_ADDR ||
-		     ep->irq_pci_fn != fn)) {
-		rockchip_pcie_prog_ep_ob_atu(rockchip, fn, r,
-					     AXI_WRAPPER_NOR_MSG,
-					     ep->irq_phys_addr, 0, 0);
-		ep->irq_pci_addr = ROCKCHIP_PCIE_EP_PCI_LEGACY_IRQ_ADDR;
-		ep->irq_pci_fn = fn;
-	}
 
 	intx &= 3;
-	if (is_asserted) {
+
+	if (do_assert) {
 		ep->irq_pending |= BIT(intx);
-		msg_code = ROCKCHIP_PCIE_MSG_CODE_ASSERT_INTA + intx;
+		rockchip_pcie_write(rockchip,
+				    PCIE_CLIENT_INT_IN_ASSERT |
+				    PCIE_CLIENT_INT_PEND_ST_PEND,
+				    PCIE_CLIENT_LEGACY_INT_CTRL);
 	} else {
 		ep->irq_pending &= ~BIT(intx);
-		msg_code = ROCKCHIP_PCIE_MSG_CODE_DEASSERT_INTA + intx;
+		rockchip_pcie_write(rockchip,
+				    PCIE_CLIENT_INT_IN_DEASSERT |
+				    PCIE_CLIENT_INT_PEND_ST_NORMAL,
+				    PCIE_CLIENT_LEGACY_INT_CTRL);
 	}
-
-	status = rockchip_pcie_read(rockchip,
-				    ROCKCHIP_PCIE_EP_FUNC_BASE(fn) +
-				    ROCKCHIP_PCIE_EP_CMD_STATUS);
-	status &= ROCKCHIP_PCIE_EP_CMD_STATUS_IS;
-
-	if ((status != 0) ^ (ep->irq_pending != 0)) {
-		status ^= ROCKCHIP_PCIE_EP_CMD_STATUS_IS;
-		rockchip_pcie_write(rockchip, status,
-				    ROCKCHIP_PCIE_EP_FUNC_BASE(fn) +
-				    ROCKCHIP_PCIE_EP_CMD_STATUS);
-	}
-
-	offset =
-	   ROCKCHIP_PCIE_MSG_ROUTING(ROCKCHIP_PCIE_MSG_ROUTING_LOCAL_INTX) |
-	   ROCKCHIP_PCIE_MSG_CODE(msg_code) | ROCKCHIP_PCIE_MSG_NO_DATA;
-	writel(0, ep->irq_cpu_addr + offset);
 }
 
 static int rockchip_pcie_ep_send_legacy_irq(struct rockchip_pcie_ep *ep, u8 fn,
@@ -417,9 +360,10 @@
 					 u8 interrupt_num)
 {
 	struct rockchip_pcie *rockchip = &ep->rockchip;
-	u16 flags, mme, data, data_mask;
+	u32 flags, mme, data, data_mask;
 	u8 msi_count;
-	u64 pci_addr, pci_addr_mask = 0xff;
+	u64 pci_addr;
+	u32 r;
 
 	/* Check MSI enable bit */
 	flags = rockchip_pcie_read(&ep->rockchip,
@@ -453,21 +397,20 @@
 				       ROCKCHIP_PCIE_EP_FUNC_BASE(fn) +
 				       ROCKCHIP_PCIE_EP_MSI_CTRL_REG +
 				       PCI_MSI_ADDRESS_LO);
-	pci_addr &= GENMASK_ULL(63, 2);
 
 	/* Set the outbound region if needed. */
-	if (unlikely(ep->irq_pci_addr != (pci_addr & ~pci_addr_mask) ||
+	if (unlikely(ep->irq_pci_addr != (pci_addr & PCIE_ADDR_MASK) ||
 		     ep->irq_pci_fn != fn)) {
-		rockchip_pcie_prog_ep_ob_atu(rockchip, fn, ep->max_regions - 1,
-					     AXI_WRAPPER_MEM_WRITE,
+		r = rockchip_ob_region(ep->irq_phys_addr);
+		rockchip_pcie_prog_ep_ob_atu(rockchip, fn, r,
 					     ep->irq_phys_addr,
-					     pci_addr & ~pci_addr_mask,
-					     pci_addr_mask + 1);
-		ep->irq_pci_addr = (pci_addr & ~pci_addr_mask);
+					     pci_addr & PCIE_ADDR_MASK,
+					     ~PCIE_ADDR_MASK + 1);
+		ep->irq_pci_addr = (pci_addr & PCIE_ADDR_MASK);
 		ep->irq_pci_fn = fn;
 	}
 
-	writew(data, ep->irq_cpu_addr + (pci_addr & pci_addr_mask));
+	writew(data, ep->irq_cpu_addr + (pci_addr & ~PCIE_ADDR_MASK));
 	return 0;
 }
 
@@ -507,6 +450,7 @@
 	.linkup_notifier = false,
 	.msi_capable = true,
 	.msix_capable = false,
+	.align = 256,
 };
 
 static const struct pci_epc_features*
@@ -548,6 +492,8 @@
 	if (err < 0 || ep->max_regions > MAX_REGION_LIMIT)
 		ep->max_regions = MAX_REGION_LIMIT;
 
+	ep->ob_region_map = 0;
+
 	err = of_property_read_u8(dev->of_node, "max-functions",
 				  &ep->epc->max_functions);
 	if (err < 0)
@@ -568,7 +514,9 @@
 	struct rockchip_pcie *rockchip;
 	struct pci_epc *epc;
 	size_t max_regions;
-	int err;
+	struct pci_epc_mem_window *windows = NULL;
+	int err, i;
+	u32 cfg_msi, cfg_msix_cp;
 
 	ep = devm_kzalloc(dev, sizeof(*ep), GFP_KERNEL);
 	if (!ep)
@@ -615,15 +563,27 @@
 	/* Only enable function 0 by default */
 	rockchip_pcie_write(rockchip, BIT(0), PCIE_CORE_PHY_FUNC_CFG);
 
-	err = pci_epc_mem_init(epc, rockchip->mem_res->start,
-			       resource_size(rockchip->mem_res), PAGE_SIZE);
+	windows = devm_kcalloc(dev, ep->max_regions,
+			       sizeof(struct pci_epc_mem_window), GFP_KERNEL);
+	if (!windows) {
+		err = -ENOMEM;
+		goto err_uninit_port;
+	}
+	for (i = 0; i < ep->max_regions; i++) {
+		windows[i].phys_base = rockchip->mem_res->start + (SZ_1M * i);
+		windows[i].size = SZ_1M;
+		windows[i].page_size = SZ_1M;
+	}
+	err = pci_epc_multi_mem_init(epc, windows, ep->max_regions);
+	devm_kfree(dev, windows);
+
 	if (err < 0) {
 		dev_err(dev, "failed to initialize the memory space\n");
 		goto err_uninit_port;
 	}
 
 	ep->irq_cpu_addr = pci_epc_mem_alloc_addr(epc, &ep->irq_phys_addr,
-						  SZ_128K);
+						  SZ_1M);
 	if (!ep->irq_cpu_addr) {
 		dev_err(dev, "failed to reserve memory space for MSI\n");
 		err = -ENOMEM;
@@ -632,6 +592,32 @@
 
 	ep->irq_pci_addr = ROCKCHIP_PCIE_EP_DUMMY_IRQ_ADDR;
 
+	/*
+	 * MSI-X is not supported but the controller still advertises the MSI-X
+	 * capability by default, which can lead to the Root Complex side
+	 * allocating MSI-X vectors which cannot be used. Avoid this by skipping
+	 * the MSI-X capability entry in the PCIe capabilities linked-list: get
+	 * the next pointer from the MSI-X entry and set that in the MSI
+	 * capability entry (which is the previous entry). This way the MSI-X
+	 * entry is skipped (left out of the linked-list) and not advertised.
+	 */
+	cfg_msi = rockchip_pcie_read(rockchip, PCIE_EP_CONFIG_BASE +
+				     ROCKCHIP_PCIE_EP_MSI_CTRL_REG);
+
+	cfg_msi &= ~ROCKCHIP_PCIE_EP_MSI_CP1_MASK;
+
+	cfg_msix_cp = rockchip_pcie_read(rockchip, PCIE_EP_CONFIG_BASE +
+					 ROCKCHIP_PCIE_EP_MSIX_CAP_REG) &
+					 ROCKCHIP_PCIE_EP_MSIX_CAP_CP_MASK;
+
+	cfg_msi |= cfg_msix_cp;
+
+	rockchip_pcie_write(rockchip, cfg_msi,
+			    PCIE_EP_CONFIG_BASE + ROCKCHIP_PCIE_EP_MSI_CTRL_REG);
+
+	rockchip_pcie_write(rockchip, PCIE_CLIENT_CONF_ENABLE,
+			    PCIE_CLIENT_CONFIG);
+
 	return 0;
 err_epc_mem_exit:
 	pci_epc_mem_exit(epc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-rockchip.c
@@ -14,6 +14,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/gpio/consumer.h>
+#include <linux/iopoll.h>
 #include <linux/of_pci.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
@@ -119,7 +120,7 @@
 
 	if (rockchip->is_rc) {
 		rockchip->ep_gpio = devm_gpiod_get_optional(dev, "ep",
-							    GPIOD_OUT_HIGH);
+							    GPIOD_OUT_LOW);
 		if (IS_ERR(rockchip->ep_gpio))
 			return dev_err_probe(dev, PTR_ERR(rockchip->ep_gpio),
 					     "failed to get ep GPIO\n");
@@ -153,6 +154,12 @@
 }
 EXPORT_SYMBOL_GPL(rockchip_pcie_parse_dt);
 
+#define rockchip_pcie_read_addr(addr) rockchip_pcie_read(rockchip, addr)
+/* 100 ms max wait time for PHY PLLs to lock */
+#define RK_PHY_PLL_LOCK_TIMEOUT_US 100000
+/* Sleep should be less than 20ms */
+#define RK_PHY_PLL_LOCK_SLEEP_US 1000
+
 int rockchip_pcie_init_port(struct rockchip_pcie *rockchip)
 {
 	struct device *dev = rockchip->dev;
@@ -254,6 +261,16 @@
 		}
 	}
 
+	err = readx_poll_timeout(rockchip_pcie_read_addr,
+				 PCIE_CLIENT_SIDE_BAND_STATUS,
+				 regs, !(regs & PCIE_CLIENT_PHY_ST),
+				 RK_PHY_PLL_LOCK_SLEEP_US,
+				 RK_PHY_PLL_LOCK_TIMEOUT_US);
+	if (err) {
+		dev_err(dev, "PHY PLLs could not lock, %d\n", err);
+		goto err_power_off_phy;
+	}
+
 	/*
 	 * Please don't reorder the deassert sequence of the following
 	 * four reset pins.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-rockchip.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-rockchip.h
@@ -38,6 +38,13 @@
 #define   PCIE_CLIENT_MODE_EP            HIWORD_UPDATE(0x0040, 0)
 #define   PCIE_CLIENT_GEN_SEL_1		  HIWORD_UPDATE(0x0080, 0)
 #define   PCIE_CLIENT_GEN_SEL_2		  HIWORD_UPDATE_BIT(0x0080)
+#define PCIE_CLIENT_LEGACY_INT_CTRL	(PCIE_CLIENT_BASE + 0x0c)
+#define   PCIE_CLIENT_INT_IN_ASSERT		HIWORD_UPDATE_BIT(0x0002)
+#define   PCIE_CLIENT_INT_IN_DEASSERT		HIWORD_UPDATE(0x0002, 0)
+#define   PCIE_CLIENT_INT_PEND_ST_PEND		HIWORD_UPDATE_BIT(0x0001)
+#define   PCIE_CLIENT_INT_PEND_ST_NORMAL	HIWORD_UPDATE(0x0001, 0)
+#define PCIE_CLIENT_SIDE_BAND_STATUS	(PCIE_CLIENT_BASE + 0x20)
+#define   PCIE_CLIENT_PHY_ST			BIT(12)
 #define PCIE_CLIENT_DEBUG_OUT_0		(PCIE_CLIENT_BASE + 0x3c)
 #define   PCIE_CLIENT_DEBUG_LTSSM_MASK		GENMASK(5, 0)
 #define   PCIE_CLIENT_DEBUG_LTSSM_L1		0x18
@@ -132,7 +139,10 @@
 
 #define PCIE_RC_RP_ATS_BASE		0x400000
 #define PCIE_RC_CONFIG_NORMAL_BASE	0x800000
+#define PCIE_EP_PF_CONFIG_REGS_BASE	0x800000
 #define PCIE_RC_CONFIG_BASE		0xa00000
+#define PCIE_EP_CONFIG_BASE		0xa00000
+#define PCIE_EP_CONFIG_DID_VID		(PCIE_EP_CONFIG_BASE + 0x00)
 #define PCIE_RC_CONFIG_RID_CCR		(PCIE_RC_CONFIG_BASE + 0x08)
 #define   PCIE_RC_CONFIG_SCC_SHIFT		16
 #define PCIE_RC_CONFIG_DCR		(PCIE_RC_CONFIG_BASE + 0xc4)
@@ -149,10 +159,13 @@
 #define PCIE_RC_CONFIG_THP_CAP		(PCIE_RC_CONFIG_BASE + 0x274)
 #define   PCIE_RC_CONFIG_THP_CAP_NEXT_MASK	GENMASK(31, 20)
 
+#define MAX_AXI_IB_ROOTPORT_REGION_NUM		3
+#define MIN_AXI_ADDR_BITS_PASSED		8
+#define PCIE_ADDR_MASK			GENMASK_ULL(63, MIN_AXI_ADDR_BITS_PASSED)
 #define PCIE_CORE_AXI_CONF_BASE		0xc00000
 #define PCIE_CORE_OB_REGION_ADDR0	(PCIE_CORE_AXI_CONF_BASE + 0x0)
 #define   PCIE_CORE_OB_REGION_ADDR0_NUM_BITS	0x3f
-#define   PCIE_CORE_OB_REGION_ADDR0_LO_ADDR	0xffffff00
+#define   PCIE_CORE_OB_REGION_ADDR0_LO_ADDR	PCIE_ADDR_MASK
 #define PCIE_CORE_OB_REGION_ADDR1	(PCIE_CORE_AXI_CONF_BASE + 0x4)
 #define PCIE_CORE_OB_REGION_DESC0	(PCIE_CORE_AXI_CONF_BASE + 0x8)
 #define PCIE_CORE_OB_REGION_DESC1	(PCIE_CORE_AXI_CONF_BASE + 0xc)
@@ -160,7 +173,7 @@
 #define PCIE_CORE_AXI_INBOUND_BASE	0xc00800
 #define PCIE_RP_IB_ADDR0		(PCIE_CORE_AXI_INBOUND_BASE + 0x0)
 #define   PCIE_CORE_IB_REGION_ADDR0_NUM_BITS	0x3f
-#define   PCIE_CORE_IB_REGION_ADDR0_LO_ADDR	0xffffff00
+#define   PCIE_CORE_IB_REGION_ADDR0_LO_ADDR	PCIE_ADDR_MASK
 #define PCIE_RP_IB_ADDR1		(PCIE_CORE_AXI_INBOUND_BASE + 0x4)
 
 /* Size of one AXI Region (not Region 0) */
@@ -175,8 +188,6 @@
 #define AXI_WRAPPER_TYPE1_CFG			0xb
 #define AXI_WRAPPER_NOR_MSG			0xc
 
-#define MAX_AXI_IB_ROOTPORT_REGION_NUM		3
-#define MIN_AXI_ADDR_BITS_PASSED		8
 #define PCIE_RC_SEND_PME_OFF			0x11960
 #define ROCKCHIP_VENDOR_ID			0x1d87
 #define PCIE_LINK_IS_L2(x) \
@@ -217,21 +228,32 @@
 #define ROCKCHIP_PCIE_EP_CMD_STATUS			0x4
 #define   ROCKCHIP_PCIE_EP_CMD_STATUS_IS		BIT(19)
 #define ROCKCHIP_PCIE_EP_MSI_CTRL_REG			0x90
+#define   ROCKCHIP_PCIE_EP_MSI_CP1_OFFSET		8
+#define   ROCKCHIP_PCIE_EP_MSI_CP1_MASK			GENMASK(15, 8)
+#define   ROCKCHIP_PCIE_EP_MSI_FLAGS_OFFSET		16
 #define   ROCKCHIP_PCIE_EP_MSI_CTRL_MMC_OFFSET		17
 #define   ROCKCHIP_PCIE_EP_MSI_CTRL_MMC_MASK		GENMASK(19, 17)
 #define   ROCKCHIP_PCIE_EP_MSI_CTRL_MME_OFFSET		20
 #define   ROCKCHIP_PCIE_EP_MSI_CTRL_MME_MASK		GENMASK(22, 20)
 #define   ROCKCHIP_PCIE_EP_MSI_CTRL_ME				BIT(16)
 #define   ROCKCHIP_PCIE_EP_MSI_CTRL_MASK_MSI_CAP	BIT(24)
+#define ROCKCHIP_PCIE_EP_MSIX_CAP_REG			0xb0
+#define   ROCKCHIP_PCIE_EP_MSIX_CAP_CP_OFFSET		8
+#define   ROCKCHIP_PCIE_EP_MSIX_CAP_CP_MASK		GENMASK(15, 8)
 #define ROCKCHIP_PCIE_EP_DUMMY_IRQ_ADDR				0x1
 #define ROCKCHIP_PCIE_EP_PCI_LEGACY_IRQ_ADDR		0x3
-#define ROCKCHIP_PCIE_EP_FUNC_BASE(fn)	(((fn) << 12) & GENMASK(19, 12))
+#define ROCKCHIP_PCIE_EP_FUNC_BASE(fn) \
+	(PCIE_EP_PF_CONFIG_REGS_BASE + (((fn) << 12) & GENMASK(19, 12)))
+#define ROCKCHIP_PCIE_EP_VIRT_FUNC_BASE(fn) \
+	(PCIE_EP_PF_CONFIG_REGS_BASE + 0x10000 + (((fn) << 12) & GENMASK(19, 12)))
+
+#define ROCKCHIP_PCIE_AT_MIN_NUM_BITS  8
+#define ROCKCHIP_PCIE_AT_MAX_NUM_BITS  20
+
 #define ROCKCHIP_PCIE_AT_IB_EP_FUNC_BAR_ADDR0(fn, bar) \
-	(PCIE_RC_RP_ATS_BASE + 0x0840 + (fn) * 0x0040 + (bar) * 0x0008)
+	(PCIE_CORE_AXI_CONF_BASE + 0x0828 + (fn) * 0x0040 + (bar) * 0x0008)
 #define ROCKCHIP_PCIE_AT_IB_EP_FUNC_BAR_ADDR1(fn, bar) \
-	(PCIE_RC_RP_ATS_BASE + 0x0844 + (fn) * 0x0040 + (bar) * 0x0008)
-#define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0(r) \
-	(PCIE_RC_RP_ATS_BASE + 0x0000 + ((r) & 0x1f) * 0x0020)
+	(PCIE_CORE_AXI_CONF_BASE + 0x082c + (fn) * 0x0040 + (bar) * 0x0008)
 #define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0_DEVFN_MASK	GENMASK(19, 12)
 #define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0_DEVFN(devfn) \
 	(((devfn) << 12) & \
@@ -239,20 +261,21 @@
 #define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0_BUS_MASK	GENMASK(27, 20)
 #define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0_BUS(bus) \
 		(((bus) << 20) & ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0_BUS_MASK)
+#define PCIE_RC_EP_ATR_OB_REGIONS_1_32 (PCIE_CORE_AXI_CONF_BASE + 0x0020)
+#define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR0(r) \
+		(PCIE_RC_EP_ATR_OB_REGIONS_1_32 + 0x0000 + ((r) & 0x1f) * 0x0020)
 #define ROCKCHIP_PCIE_AT_OB_REGION_PCI_ADDR1(r) \
-		(PCIE_RC_RP_ATS_BASE + 0x0004 + ((r) & 0x1f) * 0x0020)
+		(PCIE_RC_EP_ATR_OB_REGIONS_1_32 + 0x0004 + ((r) & 0x1f) * 0x0020)
 #define ROCKCHIP_PCIE_AT_OB_REGION_DESC0_HARDCODED_RID	BIT(23)
 #define ROCKCHIP_PCIE_AT_OB_REGION_DESC0_DEVFN_MASK	GENMASK(31, 24)
 #define ROCKCHIP_PCIE_AT_OB_REGION_DESC0_DEVFN(devfn) \
 		(((devfn) << 24) & ROCKCHIP_PCIE_AT_OB_REGION_DESC0_DEVFN_MASK)
 #define ROCKCHIP_PCIE_AT_OB_REGION_DESC0(r) \
-		(PCIE_RC_RP_ATS_BASE + 0x0008 + ((r) & 0x1f) * 0x0020)
-#define ROCKCHIP_PCIE_AT_OB_REGION_DESC1(r)	\
-		(PCIE_RC_RP_ATS_BASE + 0x000c + ((r) & 0x1f) * 0x0020)
-#define ROCKCHIP_PCIE_AT_OB_REGION_CPU_ADDR0(r) \
-		(PCIE_RC_RP_ATS_BASE + 0x0018 + ((r) & 0x1f) * 0x0020)
-#define ROCKCHIP_PCIE_AT_OB_REGION_CPU_ADDR1(r) \
-		(PCIE_RC_RP_ATS_BASE + 0x001c + ((r) & 0x1f) * 0x0020)
+		(PCIE_RC_EP_ATR_OB_REGIONS_1_32 + 0x0008 + ((r) & 0x1f) * 0x0020)
+#define ROCKCHIP_PCIE_AT_OB_REGION_DESC1(r) \
+		(PCIE_RC_EP_ATR_OB_REGIONS_1_32 + 0x000c + ((r) & 0x1f) * 0x0020)
+#define ROCKCHIP_PCIE_AT_OB_REGION_DESC2(r) \
+		(PCIE_RC_EP_ATR_OB_REGIONS_1_32 + 0x0010 + ((r) & 0x1f) * 0x0020)
 
 #define ROCKCHIP_PCIE_CORE_EP_FUNC_BAR_CFG0(fn) \
 		(PCIE_CORE_CTRL_MGMT_BASE + 0x0240 + (fn) * 0x0008)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-xdma-pl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-xdma-pl.c
@@ -0,0 +1,828 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * PCIe host controller driver for Xilinx XDMA PCIe Bridge
+ *
+ * Copyright (C) 2017 Xilinx, Inc. All rights reserved.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/irqchip/chained_irq.h>
+
+#include "../pci.h"
+
+/* Register definitions */
+#define XILINX_PCIE_REG_VSEC		0x0000012c
+#define XILINX_PCIE_REG_BIR		0x00000130
+#define XILINX_PCIE_REG_IDR		0x00000138
+#define XILINX_PCIE_REG_IMR		0x0000013c
+#define XILINX_PCIE_REG_PSCR		0x00000144
+#define XILINX_PCIE_REG_RPSC		0x00000148
+#define XILINX_PCIE_REG_MSIBASE1	0x0000014c
+#define XILINX_PCIE_REG_MSIBASE2	0x00000150
+#define XILINX_PCIE_REG_RPEFR		0x00000154
+#define XILINX_PCIE_REG_RPIFR1		0x00000158
+#define XILINX_PCIE_REG_RPIFR2		0x0000015c
+#define XILINX_PCIE_REG_IDRN            0x00000160
+#define XILINX_PCIE_REG_IDRN_MASK       0x00000164
+#define XILINX_PCIE_REG_MSI_LOW		0x00000170
+#define XILINX_PCIE_REG_MSI_HI		0x00000174
+#define XILINX_PCIE_REG_MSI_LOW_MASK	0x00000178
+#define XILINX_PCIE_REG_MSI_HI_MASK	0x0000017c
+
+/* Interrupt registers definitions */
+#define XILINX_PCIE_INTR_LINK_DOWN	BIT(0)
+#define XILINX_PCIE_INTR_HOT_RESET	BIT(3)
+#define XILINX_PCIE_INTR_CFG_TIMEOUT	BIT(8)
+#define XILINX_PCIE_INTR_CORRECTABLE	BIT(9)
+#define XILINX_PCIE_INTR_NONFATAL	BIT(10)
+#define XILINX_PCIE_INTR_FATAL		BIT(11)
+#define XILINX_PCIE_INTR_INTX		BIT(16)
+#define XILINX_PCIE_INTR_MSI		BIT(17)
+#define XILINX_PCIE_INTR_SLV_UNSUPP	BIT(20)
+#define XILINX_PCIE_INTR_SLV_UNEXP	BIT(21)
+#define XILINX_PCIE_INTR_SLV_COMPL	BIT(22)
+#define XILINX_PCIE_INTR_SLV_ERRP	BIT(23)
+#define XILINX_PCIE_INTR_SLV_CMPABT	BIT(24)
+#define XILINX_PCIE_INTR_SLV_ILLBUR	BIT(25)
+#define XILINX_PCIE_INTR_MST_DECERR	BIT(26)
+#define XILINX_PCIE_INTR_MST_SLVERR	BIT(27)
+#define XILINX_PCIE_IMR_ALL_MASK	0x0FF30FE9
+#define XILINX_PCIE_IDR_ALL_MASK	0xFFFFFFFF
+#define XILINX_PCIE_IDRN_MASK           GENMASK(19, 16)
+
+/* Root Port Error FIFO Read Register definitions */
+#define XILINX_PCIE_RPEFR_ERR_VALID	BIT(18)
+#define XILINX_PCIE_RPEFR_REQ_ID	GENMASK(15, 0)
+#define XILINX_PCIE_RPEFR_ALL_MASK	0xFFFFFFFF
+
+/* Root Port Interrupt FIFO Read Register 1 definitions */
+#define XILINX_PCIE_RPIFR1_INTR_VALID	BIT(31)
+#define XILINX_PCIE_RPIFR1_MSI_INTR	BIT(30)
+#define XILINX_PCIE_RPIFR1_INTR_MASK	GENMASK(28, 27)
+#define XILINX_PCIE_RPIFR1_ALL_MASK	0xFFFFFFFF
+#define XILINX_PCIE_RPIFR1_INTR_SHIFT	27
+#define XILINX_PCIE_IDRN_SHIFT          16
+#define XILINX_PCIE_VSEC_REV_MASK	GENMASK(19, 16)
+#define XILINX_PCIE_VSEC_REV_SHIFT	16
+#define XILINX_PCIE_FIFO_SHIFT		5
+
+/* Bridge Info Register definitions */
+#define XILINX_PCIE_BIR_ECAM_SZ_MASK	GENMASK(18, 16)
+#define XILINX_PCIE_BIR_ECAM_SZ_SHIFT	16
+
+/* Root Port Interrupt FIFO Read Register 2 definitions */
+#define XILINX_PCIE_RPIFR2_MSG_DATA	GENMASK(15, 0)
+
+/* Root Port Status/control Register definitions */
+#define XILINX_PCIE_REG_RPSC_BEN	BIT(0)
+
+/* Phy Status/Control Register definitions */
+#define XILINX_PCIE_REG_PSCR_LNKUP	BIT(11)
+
+/* ECAM definitions */
+#define ECAM_BUS_NUM_SHIFT		20
+#define ECAM_DEV_NUM_SHIFT		12
+
+/* Number of MSI IRQs */
+#define XILINX_NUM_MSI_IRQS		64
+#define INTX_NUM                        4
+
+#define DMA_BRIDGE_BASE_OFF		0xCD8
+
+enum msi_mode {
+	MSI_DECD_MODE = 1,
+	MSI_FIFO_MODE,
+};
+
+enum xdma_config {
+	XDMA_ZYNQMP_PL = 1,
+	XDMA_VERSAL_PL,
+};
+
+struct xilinx_msi {
+	struct irq_domain *msi_domain;
+	unsigned long *bitmap;
+	struct irq_domain *dev_domain;
+	struct mutex lock;		/* protect bitmap variable */
+	unsigned long msi_pages;
+	int irq_msi0;
+	int irq_msi1;
+};
+
+/**
+ * struct xilinx_pcie_port - PCIe port information
+ * @reg_base: IO Mapped Register Base
+ * @irq: Interrupt number
+ * @root_busno: Root Bus number
+ * @dev: Device pointer
+ * @leg_domain: Legacy IRQ domain pointer
+ * @resources: Bus Resources
+ * @msi: MSI information
+ * @irq_misc: Legacy and error interrupt number
+ * @msi_mode: MSI mode
+ * @xdma_config: XDMA IP configuration
+ */
+struct xilinx_pcie_port {
+	void __iomem *reg_base;
+	u32 irq;
+	u8 root_busno;
+	struct device *dev;
+	struct irq_domain *leg_domain;
+	struct list_head resources;
+	struct xilinx_msi msi;
+	int irq_misc;
+	u8 msi_mode;
+	u8 xdma_config;
+};
+
+static inline u32 pcie_read(struct xilinx_pcie_port *port, u32 reg)
+{
+	if (port->xdma_config == XDMA_ZYNQMP_PL)
+		return readl(port->reg_base + reg);
+	else
+		return readl(port->reg_base + reg + DMA_BRIDGE_BASE_OFF);
+}
+
+static inline void pcie_write(struct xilinx_pcie_port *port, u32 val, u32 reg)
+{
+	if (port->xdma_config == XDMA_ZYNQMP_PL)
+		writel(val, port->reg_base + reg);
+	else
+		writel(val, port->reg_base + reg + DMA_BRIDGE_BASE_OFF);
+}
+
+static inline bool xilinx_pcie_link_is_up(struct xilinx_pcie_port *port)
+{
+	return (pcie_read(port, XILINX_PCIE_REG_PSCR) &
+		XILINX_PCIE_REG_PSCR_LNKUP) ? 1 : 0;
+}
+
+/**
+ * xilinx_pcie_clear_err_interrupts - Clear Error Interrupts
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_clear_err_interrupts(struct xilinx_pcie_port *port)
+{
+	unsigned long val = pcie_read(port, XILINX_PCIE_REG_RPEFR);
+
+	if (val & XILINX_PCIE_RPEFR_ERR_VALID) {
+		dev_dbg(port->dev, "Requester ID %lu\n",
+			val & XILINX_PCIE_RPEFR_REQ_ID);
+		pcie_write(port, XILINX_PCIE_RPEFR_ALL_MASK,
+			   XILINX_PCIE_REG_RPEFR);
+	}
+}
+
+/**
+ * xilinx_pcie_valid_device - Check if a valid device is present on bus
+ * @bus: PCI Bus structure
+ * @devfn: device/function
+ *
+ * Return: 'true' on success and 'false' if invalid device is found
+ */
+static bool xilinx_pcie_valid_device(struct pci_bus *bus, unsigned int devfn)
+{
+	struct xilinx_pcie_port *port = bus->sysdata;
+
+	/* Check if link is up when trying to access downstream ports */
+	if (bus->number != port->root_busno)
+		if (!xilinx_pcie_link_is_up(port))
+			return false;
+
+	/* Only one device down on each root port */
+	if (bus->number == port->root_busno && devfn > 0)
+		return false;
+
+	return true;
+}
+
+/**
+ * xilinx_pcie_map_bus - Get configuration base
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ *
+ * Return: Base address of the configuration space needed to be
+ *	   accessed.
+ */
+static void __iomem *xilinx_pcie_map_bus(struct pci_bus *bus,
+					 unsigned int devfn, int where)
+{
+	struct xilinx_pcie_port *port = bus->sysdata;
+	int relbus;
+
+	if (!xilinx_pcie_valid_device(bus, devfn))
+		return NULL;
+
+	relbus = (bus->number << ECAM_BUS_NUM_SHIFT) |
+		 (devfn << ECAM_DEV_NUM_SHIFT);
+
+	return port->reg_base + relbus + where;
+}
+
+/* PCIe operations */
+static struct pci_ops xilinx_pcie_ops = {
+	.map_bus = xilinx_pcie_map_bus,
+	.read	= pci_generic_config_read,
+	.write	= pci_generic_config_write,
+};
+
+/**
+ * xilinx_pcie_enable_msi - Enable MSI support
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_enable_msi(struct xilinx_pcie_port *port)
+{
+	struct xilinx_msi *msi = &port->msi;
+	phys_addr_t msg_addr;
+
+	msi->msi_pages = __get_free_pages(GFP_KERNEL, 0);
+	msg_addr = virt_to_phys((void *)msi->msi_pages);
+	pcie_write(port, upper_32_bits(msg_addr), XILINX_PCIE_REG_MSIBASE1);
+	pcie_write(port, lower_32_bits(msg_addr), XILINX_PCIE_REG_MSIBASE2);
+}
+
+/**
+ * xilinx_pcie_intx_map - Set the handler for the INTx and mark IRQ as valid
+ * @domain: IRQ domain
+ * @irq: Virtual IRQ number
+ * @hwirq: HW interrupt number
+ *
+ * Return: Always returns 0.
+ */
+static int xilinx_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
+				irq_hw_number_t hwirq)
+{
+	irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);
+	irq_set_chip_data(irq, domain->host_data);
+	irq_set_status_flags(irq, IRQ_LEVEL);
+
+	return 0;
+}
+
+/* INTx IRQ Domain operations */
+static const struct irq_domain_ops intx_domain_ops = {
+	.map = xilinx_pcie_intx_map,
+	.xlate = pci_irqd_intx_xlate,
+};
+
+static void xilinx_pcie_handle_msi_irq(struct xilinx_pcie_port *port,
+				       u32 status_reg)
+{
+	struct xilinx_msi *msi;
+	unsigned long status;
+	u32 bit;
+	u32 virq;
+
+	msi = &port->msi;
+
+	while ((status = pcie_read(port, status_reg)) != 0) {
+		for_each_set_bit(bit, &status, 32) {
+			pcie_write(port, 1 << bit, status_reg);
+			if (status_reg == XILINX_PCIE_REG_MSI_HI)
+				bit = bit + 32;
+			virq = irq_find_mapping(msi->dev_domain, bit);
+			if (virq)
+				generic_handle_irq(virq);
+		}
+	}
+}
+
+static void xilinx_pcie_msi_handler_high(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct xilinx_pcie_port *port = irq_desc_get_handler_data(desc);
+
+	chained_irq_enter(chip, desc);
+	xilinx_pcie_handle_msi_irq(port, XILINX_PCIE_REG_MSI_HI);
+	chained_irq_exit(chip, desc);
+}
+
+static void xilinx_pcie_msi_handler_low(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct xilinx_pcie_port *port = irq_desc_get_handler_data(desc);
+
+	chained_irq_enter(chip, desc);
+	xilinx_pcie_handle_msi_irq(port, XILINX_PCIE_REG_MSI_LOW);
+	chained_irq_exit(chip, desc);
+}
+
+/**
+ * xilinx_pcie_intr_handler - Interrupt Service Handler
+ * @irq: IRQ number
+ * @data: PCIe port information
+ *
+ * Return: IRQ_HANDLED on success and IRQ_NONE on failure
+ */
+static irqreturn_t xilinx_pcie_intr_handler(int irq, void *data)
+{
+	struct xilinx_pcie_port *port = (struct xilinx_pcie_port *)data;
+	u32 val, mask, status, msi_data, bit;
+	unsigned long intr_val;
+
+	/* Read interrupt decode and mask registers */
+	val = pcie_read(port, XILINX_PCIE_REG_IDR);
+	mask = pcie_read(port, XILINX_PCIE_REG_IMR);
+
+	status = val & mask;
+	if (!status)
+		return IRQ_NONE;
+
+	if (status & XILINX_PCIE_INTR_LINK_DOWN)
+		dev_warn(port->dev, "Link Down\n");
+
+	if (status & XILINX_PCIE_INTR_HOT_RESET)
+		dev_info(port->dev, "Hot reset\n");
+
+	if (status & XILINX_PCIE_INTR_CFG_TIMEOUT)
+		dev_warn(port->dev, "ECAM access timeout\n");
+
+	if (status & XILINX_PCIE_INTR_CORRECTABLE) {
+		dev_warn(port->dev, "Correctable error message\n");
+		xilinx_pcie_clear_err_interrupts(port);
+	}
+
+	if (status & XILINX_PCIE_INTR_NONFATAL) {
+		dev_warn(port->dev, "Non fatal error message\n");
+		xilinx_pcie_clear_err_interrupts(port);
+	}
+
+	if (status & XILINX_PCIE_INTR_FATAL) {
+		dev_warn(port->dev, "Fatal error message\n");
+		xilinx_pcie_clear_err_interrupts(port);
+	}
+
+	if (status & XILINX_PCIE_INTR_INTX) {
+		/* Handle INTx Interrupt */
+		intr_val = pcie_read(port, XILINX_PCIE_REG_IDRN);
+		intr_val = intr_val >> XILINX_PCIE_IDRN_SHIFT;
+
+		for_each_set_bit(bit, &intr_val, INTX_NUM)
+			generic_handle_irq(irq_find_mapping(port->leg_domain,
+							    bit));
+	}
+
+	if (port->msi_mode == MSI_FIFO_MODE &&
+	    (status & XILINX_PCIE_INTR_MSI)) {
+		/* MSI Interrupt */
+		val = pcie_read(port, XILINX_PCIE_REG_RPIFR1);
+
+		if (!(val & XILINX_PCIE_RPIFR1_INTR_VALID)) {
+			dev_warn(port->dev, "RP Intr FIFO1 read error\n");
+			goto error;
+		}
+
+		if (val & XILINX_PCIE_RPIFR1_MSI_INTR) {
+			msi_data = pcie_read(port, XILINX_PCIE_REG_RPIFR2) &
+				   XILINX_PCIE_RPIFR2_MSG_DATA;
+
+			/* Clear interrupt FIFO register 1 */
+			pcie_write(port, XILINX_PCIE_RPIFR1_ALL_MASK,
+				   XILINX_PCIE_REG_RPIFR1);
+
+			if (IS_ENABLED(CONFIG_PCI_MSI)) {
+				/* Handle MSI Interrupt */
+				val = irq_find_mapping(port->msi.dev_domain,
+						       msi_data);
+				if (val)
+					generic_handle_irq(val);
+			}
+		}
+	}
+
+	if (status & XILINX_PCIE_INTR_SLV_UNSUPP)
+		dev_warn(port->dev, "Slave unsupported request\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_UNEXP)
+		dev_warn(port->dev, "Slave unexpected completion\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_COMPL)
+		dev_warn(port->dev, "Slave completion timeout\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_ERRP)
+		dev_warn(port->dev, "Slave Error Poison\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_CMPABT)
+		dev_warn(port->dev, "Slave Completer Abort\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_ILLBUR)
+		dev_warn(port->dev, "Slave Illegal Burst\n");
+
+	if (status & XILINX_PCIE_INTR_MST_DECERR)
+		dev_warn(port->dev, "Master decode error\n");
+
+	if (status & XILINX_PCIE_INTR_MST_SLVERR)
+		dev_warn(port->dev, "Master slave error\n");
+
+error:
+	/* Clear the Interrupt Decode register */
+	pcie_write(port, status, XILINX_PCIE_REG_IDR);
+
+	return IRQ_HANDLED;
+}
+
+static struct irq_chip xilinx_msi_irq_chip = {
+	.name = "xilinx_pcie:msi",
+	.irq_enable = pci_msi_unmask_irq,
+	.irq_disable = pci_msi_mask_irq,
+	.irq_mask = pci_msi_mask_irq,
+	.irq_unmask = pci_msi_unmask_irq,
+};
+
+static struct msi_domain_info xilinx_msi_domain_info = {
+	.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
+		MSI_FLAG_MULTI_PCI_MSI),
+	.chip = &xilinx_msi_irq_chip,
+};
+
+static void xilinx_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
+{
+	struct xilinx_pcie_port *pcie = irq_data_get_irq_chip_data(data);
+	struct xilinx_msi *msi = &pcie->msi;
+	phys_addr_t msi_addr;
+
+	msi_addr = virt_to_phys((void *)msi->msi_pages);
+	msg->address_lo = lower_32_bits(msi_addr);
+	msg->address_hi = upper_32_bits(msi_addr);
+	msg->data = data->hwirq;
+}
+
+static int xilinx_msi_set_affinity(struct irq_data *irq_data,
+				   const struct cpumask *mask, bool force)
+{
+	return -EINVAL;
+}
+
+static struct irq_chip xilinx_irq_chip = {
+	.name = "Xilinx MSI",
+	.irq_compose_msi_msg = xilinx_compose_msi_msg,
+	.irq_set_affinity = xilinx_msi_set_affinity,
+};
+
+static int xilinx_irq_domain_alloc(struct irq_domain *domain, unsigned int virq,
+				   unsigned int nr_irqs, void *args)
+{
+	struct xilinx_pcie_port *pcie = domain->host_data;
+	struct xilinx_msi *msi = &pcie->msi;
+	int bit;
+	int i;
+
+	mutex_lock(&msi->lock);
+	bit = bitmap_find_free_region(msi->bitmap, XILINX_NUM_MSI_IRQS,
+				      get_count_order(nr_irqs));
+	if (bit < 0) {
+		mutex_unlock(&msi->lock);
+		return -ENOSPC;
+	}
+
+	for (i = 0; i < nr_irqs; i++) {
+		irq_domain_set_info(domain, virq + i, bit + i, &xilinx_irq_chip,
+				    domain->host_data, handle_simple_irq,
+				    NULL, NULL);
+	}
+	mutex_unlock(&msi->lock);
+	return 0;
+}
+
+static void xilinx_irq_domain_free(struct irq_domain *domain, unsigned int virq,
+				   unsigned int nr_irqs)
+{
+	struct irq_data *data = irq_domain_get_irq_data(domain, virq);
+	struct xilinx_pcie_port *pcie = irq_data_get_irq_chip_data(data);
+	struct xilinx_msi *msi = &pcie->msi;
+
+	mutex_lock(&msi->lock);
+	bitmap_release_region(msi->bitmap, data->hwirq,
+			      get_count_order(nr_irqs));
+	mutex_unlock(&msi->lock);
+}
+
+static const struct irq_domain_ops dev_msi_domain_ops = {
+	.alloc  = xilinx_irq_domain_alloc,
+	.free   = xilinx_irq_domain_free,
+};
+
+static int xilinx_pcie_init_msi_irq_domain(struct xilinx_pcie_port *port)
+{
+	struct fwnode_handle *fwnode = of_node_to_fwnode(port->dev->of_node);
+	struct xilinx_msi *msi = &port->msi;
+	int size = BITS_TO_LONGS(XILINX_NUM_MSI_IRQS) * sizeof(long);
+
+	msi->dev_domain = irq_domain_add_linear(NULL, XILINX_NUM_MSI_IRQS,
+						&dev_msi_domain_ops, port);
+	if (!msi->dev_domain) {
+		dev_err(port->dev, "failed to create dev IRQ domain\n");
+		return -ENOMEM;
+	}
+	msi->msi_domain = pci_msi_create_irq_domain(fwnode,
+						    &xilinx_msi_domain_info,
+						    msi->dev_domain);
+	if (!msi->msi_domain) {
+		dev_err(port->dev, "failed to create msi IRQ domain\n");
+		irq_domain_remove(msi->dev_domain);
+		return -ENOMEM;
+	}
+
+	mutex_init(&msi->lock);
+	msi->bitmap = kzalloc(size, GFP_KERNEL);
+	if (!msi->bitmap)
+		return -ENOMEM;
+
+	xilinx_pcie_enable_msi(port);
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_init_irq_domain - Initialize IRQ domain
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_init_irq_domain(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *pcie_intc_node;
+
+	/* Setup INTx */
+	pcie_intc_node = of_get_next_child(node, NULL);
+	if (!pcie_intc_node) {
+		dev_err(dev, "No PCIe Intc node found\n");
+		return PTR_ERR(pcie_intc_node);
+	}
+
+	port->leg_domain = irq_domain_add_linear(pcie_intc_node, INTX_NUM,
+						 &intx_domain_ops,
+						 port);
+	if (!port->leg_domain) {
+		dev_err(dev, "Failed to get a INTx IRQ domain\n");
+		return PTR_ERR(port->leg_domain);
+	}
+
+	xilinx_pcie_init_msi_irq_domain(port);
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_init_port - Initialize hardware
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_init_port(struct xilinx_pcie_port *port)
+{
+	if (xilinx_pcie_link_is_up(port))
+		dev_info(port->dev, "PCIe Link is UP\n");
+	else
+		dev_info(port->dev, "PCIe Link is DOWN\n");
+
+	/* Disable all interrupts */
+	pcie_write(port, ~XILINX_PCIE_IDR_ALL_MASK,
+		   XILINX_PCIE_REG_IMR);
+
+	/* Clear pending interrupts */
+	pcie_write(port, pcie_read(port, XILINX_PCIE_REG_IDR) &
+			 XILINX_PCIE_IMR_ALL_MASK,
+		   XILINX_PCIE_REG_IDR);
+
+	/* Enable all interrupts */
+	pcie_write(port, XILINX_PCIE_IMR_ALL_MASK, XILINX_PCIE_REG_IMR);
+	pcie_write(port, XILINX_PCIE_IDRN_MASK, XILINX_PCIE_REG_IDRN_MASK);
+	if (port->msi_mode == MSI_DECD_MODE) {
+		pcie_write(port, XILINX_PCIE_IDR_ALL_MASK,
+			   XILINX_PCIE_REG_MSI_LOW_MASK);
+		pcie_write(port, XILINX_PCIE_IDR_ALL_MASK,
+			   XILINX_PCIE_REG_MSI_HI_MASK);
+	}
+	/* Enable the Bridge enable bit */
+	pcie_write(port, pcie_read(port, XILINX_PCIE_REG_RPSC) |
+			 XILINX_PCIE_REG_RPSC_BEN,
+		   XILINX_PCIE_REG_RPSC);
+
+}
+
+static int xilinx_request_misc_irq(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	int err;
+
+	port->irq_misc = platform_get_irq_byname(pdev, "misc");
+	if (port->irq_misc <= 0) {
+		dev_err(dev, "Unable to find misc IRQ line\n");
+		return port->irq_misc;
+	}
+	err = devm_request_irq(dev, port->irq_misc,
+			       xilinx_pcie_intr_handler,
+			       IRQF_SHARED | IRQF_NO_THREAD,
+			       "xilinx-pcie", port);
+	if (err) {
+		dev_err(dev, "unable to request misc IRQ line %d\n",
+			port->irq_misc);
+		return err;
+	}
+
+	return 0;
+}
+
+static int xilinx_request_msi_irq(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+
+	port->msi.irq_msi0 = platform_get_irq_byname(pdev, "msi0");
+	if (port->msi.irq_msi0 <= 0) {
+		dev_err(dev, "Unable to find msi0 IRQ line\n");
+		return port->msi.irq_msi0;
+	}
+
+	irq_set_chained_handler_and_data(port->msi.irq_msi0,
+					 xilinx_pcie_msi_handler_low,
+					 port);
+
+	port->msi.irq_msi1 = platform_get_irq_byname(pdev, "msi1");
+	if (port->msi.irq_msi1 <= 0) {
+		dev_err(dev, "Unable to find msi1 IRQ line\n");
+		return port->msi.irq_msi1;
+	}
+
+	irq_set_chained_handler_and_data(port->msi.irq_msi1,
+					 xilinx_pcie_msi_handler_high,
+					 port);
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_parse_dt - Parse Device tree
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_parse_dt(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct device_node *node = dev->of_node;
+	struct resource regs;
+	const char *type;
+	int err, mode_val, val;
+
+	if (of_device_is_compatible(node, "xlnx,xdma-host-3.00"))
+		port->xdma_config = XDMA_ZYNQMP_PL;
+	else if (of_device_is_compatible(node, "xlnx,pcie-dma-versal-2.0"))
+		port->xdma_config = XDMA_VERSAL_PL;
+
+	if (port->xdma_config == XDMA_ZYNQMP_PL ||
+	    port->xdma_config == XDMA_VERSAL_PL) {
+		type = of_get_property(node, "device_type", NULL);
+		if (!type || strcmp(type, "pci")) {
+			dev_err(dev, "invalid \"device_type\" %s\n", type);
+			return -EINVAL;
+		}
+
+		err = of_address_to_resource(node, 0, &regs);
+		if (err) {
+			dev_err(dev, "missing \"reg\" property\n");
+			return err;
+		}
+
+		port->reg_base = devm_ioremap_resource(dev, &regs);
+		if (IS_ERR(port->reg_base))
+			return PTR_ERR(port->reg_base);
+
+		if (port->xdma_config == XDMA_ZYNQMP_PL) {
+			val = pcie_read(port, XILINX_PCIE_REG_BIR);
+			val = (val >> XILINX_PCIE_FIFO_SHIFT) & MSI_DECD_MODE;
+			mode_val = pcie_read(port, XILINX_PCIE_REG_VSEC) &
+					XILINX_PCIE_VSEC_REV_MASK;
+			mode_val = mode_val >> XILINX_PCIE_VSEC_REV_SHIFT;
+			if (mode_val && !val) {
+				port->msi_mode = MSI_DECD_MODE;
+				dev_info(dev, "Using MSI Decode mode\n");
+			} else {
+				port->msi_mode = MSI_FIFO_MODE;
+				dev_info(dev, "Using MSI FIFO mode\n");
+			}
+		}
+
+		if (port->xdma_config == XDMA_VERSAL_PL)
+			port->msi_mode = MSI_DECD_MODE;
+
+		if (port->msi_mode == MSI_DECD_MODE) {
+			err = xilinx_request_misc_irq(port);
+			if (err)
+				return err;
+
+			err = xilinx_request_msi_irq(port);
+			if (err)
+				return err;
+
+		} else if (port->msi_mode == MSI_FIFO_MODE) {
+			port->irq = irq_of_parse_and_map(node, 0);
+			if (!port->irq) {
+				dev_err(dev, "Unable to find IRQ line\n");
+				return -ENXIO;
+			}
+
+			err = devm_request_irq(dev, port->irq,
+					       xilinx_pcie_intr_handler,
+					       IRQF_SHARED | IRQF_NO_THREAD,
+					       "xilinx-pcie", port);
+			if (err) {
+				dev_err(dev, "unable to request irq %d\n",
+					port->irq);
+				return err;
+			}
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_probe - Probe function
+ * @pdev: Platform device pointer
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_probe(struct platform_device *pdev)
+{
+	struct xilinx_pcie_port *port;
+	struct device *dev = &pdev->dev;
+	struct pci_bus *bus;
+	struct pci_bus *child;
+	struct pci_host_bridge *bridge;
+	int err;
+	LIST_HEAD(res);
+
+	bridge = devm_pci_alloc_host_bridge(dev, sizeof(*port));
+	if (!bridge)
+		return -ENODEV;
+
+	port = pci_host_bridge_priv(bridge);
+
+	port->dev = dev;
+
+	err = xilinx_pcie_parse_dt(port);
+	if (err) {
+		dev_err(dev, "Parsing DT failed\n");
+		return err;
+	}
+
+	xilinx_pcie_init_port(port);
+
+	err = xilinx_pcie_init_irq_domain(port);
+	if (err) {
+		dev_err(dev, "Failed creating IRQ Domain\n");
+		return err;
+	}
+
+	list_splice_init(&res, &bridge->windows);
+	bridge->dev.parent = dev;
+	bridge->sysdata = port;
+	bridge->busnr = port->root_busno;
+	bridge->ops = &xilinx_pcie_ops;
+	bridge->map_irq = of_irq_parse_and_map_pci;
+	bridge->swizzle_irq = pci_common_swizzle;
+
+	err = pci_scan_root_bus_bridge(bridge);
+	if (err)
+		return err;
+
+	bus = bridge->bus;
+
+	pci_assign_unassigned_bus_resources(bus);
+	list_for_each_entry(child, &bus->children, node)
+		pcie_bus_configure_settings(child);
+	pci_bus_add_devices(bus);
+	return 0;
+}
+
+static const struct of_device_id xilinx_pcie_of_match[] = {
+	{ .compatible = "xlnx,xdma-host-3.00", },
+	{ .compatible = "xlnx,pcie-dma-versal-2.0", },
+	{}
+};
+
+static struct platform_driver xilinx_pcie_driver = {
+	.driver = {
+		.name = "xilinx-xdma-pcie",
+		.of_match_table = xilinx_pcie_of_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = xilinx_pcie_probe,
+};
+
+builtin_platform_driver(xilinx_pcie_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-xilinx-cpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-xilinx-cpm.c
@@ -556,13 +556,15 @@
 		return err;
 
 	bus = resource_list_first_type(&bridge->windows, IORESOURCE_BUS);
-	if (!bus)
-		return -ENODEV;
+	if (!bus) {
+		err = -ENODEV;
+		goto err_free_irq_domains;
+	}
 
 	err = xilinx_cpm_pcie_parse_dt(port, bus->res);
 	if (err) {
 		dev_err(dev, "Parsing DT failed\n");
-		goto err_parse_dt;
+		goto err_free_irq_domains;
 	}
 
 	xilinx_cpm_pcie_init_port(port);
@@ -586,7 +588,7 @@
 	xilinx_cpm_free_interrupts(port);
 err_setup_irq:
 	pci_ecam_free(port->cfg);
-err_parse_dt:
+err_free_irq_domains:
 	xilinx_cpm_free_irq_domains(port);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/pcie-xilinx-nwl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/pcie-xilinx-nwl.c
@@ -81,8 +81,8 @@
 #define MSGF_MISC_SR_NON_FATAL_DEV	BIT(22)
 #define MSGF_MISC_SR_FATAL_DEV		BIT(23)
 #define MSGF_MISC_SR_LINK_DOWN		BIT(24)
-#define MSGF_MSIC_SR_LINK_AUTO_BWIDTH	BIT(25)
-#define MSGF_MSIC_SR_LINK_BWIDTH	BIT(26)
+#define MSGF_MISC_SR_LINK_AUTO_BWIDTH	BIT(25)
+#define MSGF_MISC_SR_LINK_BWIDTH	BIT(26)
 
 #define MSGF_MISC_SR_MASKALL		(MSGF_MISC_SR_RXMSG_AVAIL | \
 					MSGF_MISC_SR_RXMSG_OVER | \
@@ -97,8 +97,8 @@
 					MSGF_MISC_SR_NON_FATAL_DEV | \
 					MSGF_MISC_SR_FATAL_DEV | \
 					MSGF_MISC_SR_LINK_DOWN | \
-					MSGF_MSIC_SR_LINK_AUTO_BWIDTH | \
-					MSGF_MSIC_SR_LINK_BWIDTH)
+					MSGF_MISC_SR_LINK_AUTO_BWIDTH | \
+					MSGF_MISC_SR_LINK_BWIDTH)
 
 /* Legacy interrupt status mask bits */
 #define MSGF_LEG_SR_INTA		BIT(0)
@@ -302,10 +302,10 @@
 	if (misc_stat & MSGF_MISC_SR_FATAL_DEV)
 		dev_err(dev, "Fatal Error Detected\n");
 
-	if (misc_stat & MSGF_MSIC_SR_LINK_AUTO_BWIDTH)
+	if (misc_stat & MSGF_MISC_SR_LINK_AUTO_BWIDTH)
 		dev_info(dev, "Link Autonomous Bandwidth Management Status bit set\n");
 
-	if (misc_stat & MSGF_MSIC_SR_LINK_BWIDTH)
+	if (misc_stat & MSGF_MISC_SR_LINK_BWIDTH)
 		dev_info(dev, "Link Bandwidth Management Status bit set\n");
 
 	/* Clear misc interrupt status */
@@ -376,7 +376,7 @@
 	u32 mask;
 	u32 val;
 
-	mask = 1 << (data->hwirq - 1);
+	mask = 1 << data->hwirq;
 	raw_spin_lock_irqsave(&pcie->leg_mask_lock, flags);
 	val = nwl_bridge_readl(pcie, MSGF_LEG_MASK);
 	nwl_bridge_writel(pcie, (val & (~mask)), MSGF_LEG_MASK);
@@ -390,7 +390,7 @@
 	u32 mask;
 	u32 val;
 
-	mask = 1 << (data->hwirq - 1);
+	mask = 1 << data->hwirq;
 	raw_spin_lock_irqsave(&pcie->leg_mask_lock, flags);
 	val = nwl_bridge_readl(pcie, MSGF_LEG_MASK);
 	nwl_bridge_writel(pcie, (val | mask), MSGF_LEG_MASK);
@@ -476,7 +476,7 @@
 
 	for (i = 0; i < nr_irqs; i++) {
 		irq_domain_set_info(domain, virq + i, bit + i, &nwl_irq_chip,
-				domain->host_data, handle_simple_irq,
+				    domain->host_data, handle_simple_irq,
 				NULL, NULL);
 	}
 	mutex_unlock(&msi->lock);
@@ -484,7 +484,7 @@
 }
 
 static void nwl_irq_domain_free(struct irq_domain *domain, unsigned int virq,
-					unsigned int nr_irqs)
+				unsigned int nr_irqs)
 {
 	struct irq_data *data = irq_domain_get_irq_data(domain, virq);
 	struct nwl_pcie *pcie = irq_data_get_irq_chip_data(data);
@@ -738,7 +738,6 @@
 	/* Enable all misc interrupts */
 	nwl_bridge_writel(pcie, MSGF_MISC_SR_MASKALL, MSGF_MISC_MASK);
 
-
 	/* Disable all legacy interrupts */
 	nwl_bridge_writel(pcie, (u32)~MSGF_LEG_SR_MASKALL, MSGF_LEG_MASK);
 
@@ -808,6 +807,7 @@
 		return -ENODEV;
 
 	pcie = pci_host_bridge_priv(bridge);
+	platform_set_drvdata(pdev, pcie);
 
 	pcie->dev = dev;
 	pcie->ecam_value = NWL_ECAM_VALUE_DEFAULT;
@@ -831,13 +831,13 @@
 	err = nwl_pcie_bridge_init(pcie);
 	if (err) {
 		dev_err(dev, "HW Initialization failed\n");
-		return err;
+		goto err_clk;
 	}
 
 	err = nwl_pcie_init_irq_domain(pcie);
 	if (err) {
 		dev_err(dev, "Failed creating IRQ Domain\n");
-		return err;
+		goto err_clk;
 	}
 
 	bridge->sysdata = pcie;
@@ -847,11 +847,24 @@
 		err = nwl_pcie_enable_msi(pcie);
 		if (err < 0) {
 			dev_err(dev, "failed to enable MSI support: %d\n", err);
-			return err;
+			goto err_clk;
 		}
 	}
 
-	return pci_host_probe(bridge);
+	err = pci_host_probe(bridge);
+	if (!err)
+		return 0;
+
+err_clk:
+	clk_disable_unprepare(pcie->clk);
+	return err;
+}
+
+static void nwl_pcie_remove(struct platform_device *pdev)
+{
+	struct nwl_pcie *pcie = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(pcie->clk);
 }
 
 static struct platform_driver nwl_pcie_driver = {
@@ -861,5 +874,6 @@
 		.of_match_table = nwl_pcie_of_match,
 	},
 	.probe = nwl_pcie_probe,
+	.remove_new = nwl_pcie_remove,
 };
 builtin_platform_driver(nwl_pcie_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/controller/vmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/controller/vmd.c
@@ -658,6 +658,21 @@
 	return 0;
 }
 
+/*
+ * Since VMD is an aperture to regular PCIe root ports, only allow it to
+ * control features that the OS is allowed to control on the physical PCI bus.
+ */
+static void vmd_copy_host_bridge_flags(struct pci_host_bridge *root_bridge,
+				       struct pci_host_bridge *vmd_bridge)
+{
+	vmd_bridge->native_pcie_hotplug = root_bridge->native_pcie_hotplug;
+	vmd_bridge->native_shpc_hotplug = root_bridge->native_shpc_hotplug;
+	vmd_bridge->native_aer = root_bridge->native_aer;
+	vmd_bridge->native_pme = root_bridge->native_pme;
+	vmd_bridge->native_ltr = root_bridge->native_ltr;
+	vmd_bridge->native_dpc = root_bridge->native_dpc;
+}
+
 static int vmd_enable_domain(struct vmd_dev *vmd, unsigned long features)
 {
 	struct pci_sysdata *sd = &vmd->sysdata;
@@ -794,9 +809,18 @@
 		return -ENODEV;
 	}
 
+	vmd_copy_host_bridge_flags(pci_find_host_bridge(vmd->dev->bus),
+				   to_pci_host_bridge(vmd->bus->bridge));
+
 	vmd_attach_resources(vmd);
 	if (vmd->irq_domain)
 		dev_set_msi_domain(&vmd->bus->dev, vmd->irq_domain);
+	else
+		dev_set_msi_domain(&vmd->bus->dev,
+				   dev_get_msi_domain(&vmd->dev->dev));
+
+	WARN(sysfs_create_link(&vmd->dev->dev.kobj, &vmd->bus->dev.kobj,
+			       "domain"), "Can't create symlink to domain\n");
 
 	vmd_acpi_begin();
 
@@ -814,9 +838,6 @@
 	pci_bus_add_devices(vmd->bus);
 
 	vmd_acpi_end();
-
-	WARN(sysfs_create_link(&vmd->dev->dev.kobj, &vmd->bus->dev.kobj,
-			       "domain"), "Can't create symlink to domain\n");
 	return 0;
 }
 
@@ -873,14 +894,21 @@
 {
 	struct vmd_dev *vmd = pci_get_drvdata(dev);
 
-	sysfs_remove_link(&vmd->dev->dev.kobj, "domain");
 	pci_stop_root_bus(vmd->bus);
+	sysfs_remove_link(&vmd->dev->dev.kobj, "domain");
 	pci_remove_root_bus(vmd->bus);
 	vmd_cleanup_srcu(vmd);
 	vmd_detach_resources(vmd);
 	vmd_remove_irq_domain(vmd);
 }
 
+static void vmd_shutdown(struct pci_dev *dev)
+{
+        struct vmd_dev *vmd = pci_get_drvdata(dev);
+
+        vmd_remove_irq_domain(vmd);
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int vmd_suspend(struct device *dev)
 {
@@ -900,6 +928,11 @@
 	struct vmd_dev *vmd = pci_get_drvdata(pdev);
 	int err, i;
 
+       if (vmd->irq_domain)
+               vmd_set_msi_remapping(vmd, true);
+       else
+               vmd_set_msi_remapping(vmd, false);
+
 	for (i = 0; i < vmd->msix_count; i++) {
 		err = devm_request_irq(dev, pci_irq_vector(pdev, i),
 				       vmd_irq, IRQF_NO_THREAD,
@@ -941,6 +974,7 @@
 	.id_table	= vmd_ids,
 	.probe		= vmd_probe,
 	.remove		= vmd_remove,
+	.shutdown	= vmd_shutdown,
 	.driver		= {
 		.pm	= &vmd_dev_pm_ops,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/endpoint/functions/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/endpoint/functions/Kconfig
@@ -25,3 +25,14 @@
 	  device tree.
 
 	  If in doubt, say "N" to disable Endpoint NTB driver.
+
+config PCI_EPF_VNTB
+        tristate "PCI Endpoint NTB driver"
+        depends on PCI_ENDPOINT
+        select CONFIGFS_FS
+        help
+          Select this configuration option to enable the Non-Transparent
+          Bridge (NTB) driver for PCIe Endpoint. NTB driver implements NTB
+          between PCI Root Port and PCIe Endpoint.
+
+          If in doubt, say "N" to disable Endpoint NTB driver.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/endpoint/functions/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/endpoint/functions/Makefile
@@ -5,3 +5,4 @@
 
 obj-$(CONFIG_PCI_EPF_TEST)		+= pci-epf-test.o
 obj-$(CONFIG_PCI_EPF_NTB)		+= pci-epf-ntb.o
+obj-$(CONFIG_PCI_EPF_VNTB) 		+= pci-epf-vntb.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/endpoint/functions/pci-epf-test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/endpoint/functions/pci-epf-test.c
@@ -285,7 +285,17 @@
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 	} else {
-		memcpy(dst_addr, src_addr, reg->size);
+		void *buf;
+
+		buf = kzalloc(reg->size, GFP_KERNEL);
+		if (!buf) {
+			ret = -ENOMEM;
+			goto err_map_addr;
+		}
+
+		memcpy_fromio(buf, src_addr, reg->size);
+		memcpy_toio(dst_addr, buf, reg->size);
+		kfree(buf);
 	}
 	ktime_get_ts64(&end);
 	pci_epf_test_print_rate("COPY", reg->size, &start, &end, use_dma);
@@ -441,7 +451,7 @@
 		if (!epf_test->dma_supported) {
 			dev_err(dev, "Cannot transfer data using DMA\n");
 			ret = -EINVAL;
-			goto err_map_addr;
+			goto err_dma_map;
 		}
 
 		src_phys_addr = dma_map_single(dma_dev, buf, reg->size,
@@ -617,7 +627,6 @@
 
 	cancel_delayed_work(&epf_test->cmd_handler);
 	pci_epf_test_clean_dma_chan(epf_test);
-	pci_epc_stop(epc);
 	for (bar = 0; bar < PCI_STD_NUM_BARS; bar++) {
 		epf_bar = &epf->bar[bar];
 
@@ -874,7 +883,7 @@
 	if (ret)
 		epf_test->dma_supported = false;
 
-	if (linkup_notifier) {
+	if (linkup_notifier || core_init_notifier) {
 		epf->nb.notifier_call = pci_epf_test_notifier;
 		pci_epc_register_notifier(epc, &epf->nb);
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/endpoint/functions/pci-epf-vntb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/endpoint/functions/pci-epf-vntb.c
@@ -0,0 +1,1427 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Endpoint Function Driver to implement Non-Transparent Bridge functionality
+ * Between PCI RC and EP
+ *
+ * Copyright (C) 2020 Texas Instruments
+ * Copyright (C) 2022 NXP
+ *
+ * Based on pci-epf-ntb.c
+ * Author: Frank Li <Frank.Li@nxp.com>
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ */
+
+/**
+ * +------------+         +---------------------------------------+
+ * |            |         |                                       |
+ * +------------+         |                        +--------------+
+ * | NTB        |         |                        | NTB          |
+ * | NetDev     |         |                        | NetDev       |
+ * +------------+         |                        +--------------+
+ * | NTB        |         |                        | NTB          |
+ * | Transfer   |         |                        | Transfer     |
+ * +------------+         |                        +--------------+
+ * |            |         |                        |              |
+ * |  PCI NTB   |         |                        |              |
+ * |    EPF     |         |                        |              |
+ * |   Driver   |         |                        | PCI Virtual  |
+ * |            |         +---------------+        | NTB Driver   |
+ * |            |         | PCI EP NTB    |<------>|              |
+ * |            |         |  FN Driver    |        |              |
+ * +------------+         +---------------+        +--------------+
+ * |            |         |               |        |              |
+ * |  PCI Bus   | <-----> |  PCI EP Bus   |        |  Virtual PCI |
+ * |            |  PCI    |               |        |     Bus      |
+ * +------------+         +---------------+--------+--------------+
+ * PCIe Root Port                        PCI EP
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include <linux/pci-epc.h>
+#include <linux/pci-epf.h>
+#include <linux/ntb.h>
+
+static struct workqueue_struct *kpcintb_workqueue;
+
+#define COMMAND_CONFIGURE_DOORBELL	1
+#define COMMAND_TEARDOWN_DOORBELL	2
+#define COMMAND_CONFIGURE_MW		3
+#define COMMAND_TEARDOWN_MW		4
+#define COMMAND_LINK_UP			5
+#define COMMAND_LINK_DOWN		6
+
+#define COMMAND_STATUS_OK		1
+#define COMMAND_STATUS_ERROR		2
+
+#define LINK_STATUS_UP			BIT(0)
+
+#define SPAD_COUNT			64
+#define DB_COUNT			4
+#define NTB_MW_OFFSET			2
+#define DB_COUNT_MASK			GENMASK(15, 0)
+#define MSIX_ENABLE			BIT(16)
+#define MAX_DB_COUNT			32
+#define MAX_MW				4
+
+enum epf_ntb_bar {
+	BAR_CONFIG,
+	BAR_DB,
+	BAR_MW0,
+	BAR_MW1,
+	BAR_MW2,
+};
+
+/*
+ * +--------------------------------------------------+ Base
+ * |                                                  |
+ * |                                                  |
+ * |                                                  |
+ * |          Common Control Register                 |
+ * |                                                  |
+ * |                                                  |
+ * |                                                  |
+ * +-----------------------+--------------------------+ Base+span_offset
+ * |                       |                          |
+ * |    Peer Span Space    |    Span Space            |
+ * |                       |                          |
+ * |                       |                          |
+ * +-----------------------+--------------------------+ Base+span_offset
+ * |                       |                          |     +span_count * 4
+ * |                       |                          |
+ * |     Span Space        |   Peer Span Space        |
+ * |                       |                          |
+ * +-----------------------+--------------------------+
+ *       Virtual PCI             PCIe Endpoint
+ *       NTB Driver               NTB Driver
+ */
+struct epf_ntb_ctrl {
+	u32     command;
+	u32     argument;
+	u16     command_status;
+	u16     link_status;
+	u32     topology;
+	u64     addr;
+	u64     size;
+	u32     num_mws;
+	u32	reserved;
+	u32     spad_offset;
+	u32     spad_count;
+	u32	db_entry_size;
+	u32     db_data[MAX_DB_COUNT];
+	u32     db_offset[MAX_DB_COUNT];
+} __packed;
+
+struct epf_ntb {
+	struct ntb_dev ntb;
+	struct pci_epf *epf;
+	struct config_group group;
+
+	u32 num_mws;
+	u32 db_count;
+	u32 spad_count;
+	u64 mws_size[MAX_MW];
+	u64 db;
+	u32 vbus_number;
+	u16 vntb_pid;
+	u16 vntb_vid;
+
+	bool linkup;
+	u32 spad_size;
+
+	enum pci_barno epf_ntb_bar[6];
+
+	struct epf_ntb_ctrl *reg;
+
+	phys_addr_t epf_db_phy;
+	void __iomem *epf_db;
+
+	phys_addr_t vpci_mw_phy[MAX_MW];
+	void __iomem *vpci_mw_addr[MAX_MW];
+
+	struct delayed_work cmd_handler;
+};
+
+#define to_epf_ntb(epf_group) container_of((epf_group), struct epf_ntb, group)
+#define ntb_ndev(__ntb) container_of(__ntb, struct epf_ntb, ntb)
+
+static struct pci_epf_header epf_ntb_header = {
+	.vendorid	= PCI_ANY_ID,
+	.deviceid	= PCI_ANY_ID,
+	.baseclass_code	= PCI_BASE_CLASS_MEMORY,
+	.interrupt_pin	= PCI_INTERRUPT_INTA,
+};
+
+/**
+ * epf_ntb_link_up() - Raise link_up interrupt to Virtual Host
+ * @ntb: NTB device that facilitates communication between HOST and VHOST
+ * @link_up: true or false indicating Link is UP or Down
+ *
+ * Once NTB function in HOST invoke ntb_link_enable(),
+ * this NTB function driver will trigger a link event to vhost.
+ */
+static int epf_ntb_link_up(struct epf_ntb *ntb, bool link_up)
+{
+	if (link_up)
+		ntb->reg->link_status |= LINK_STATUS_UP;
+	else
+		ntb->reg->link_status &= ~LINK_STATUS_UP;
+
+	ntb_link_event(&ntb->ntb);
+	return 0;
+}
+
+/**
+ * epf_ntb_configure_mw() - Configure the Outbound Address Space for vhost
+ *   to access the memory window of host
+ * @ntb: NTB device that facilitates communication between host and vhost
+ * @mw: Index of the memory window (either 0, 1, 2 or 3)
+ *
+ *                          EP Outbound Window
+ * +--------+              +-----------+
+ * |        |              |           |
+ * |        |              |           |
+ * |        |              |           |
+ * |        |              |           |
+ * |        |              +-----------+
+ * | Virtual|              | Memory Win|
+ * | NTB    | -----------> |           |
+ * | Driver |              |           |
+ * |        |              +-----------+
+ * |        |              |           |
+ * |        |              |           |
+ * +--------+              +-----------+
+ *  VHost                   PCI EP
+ */
+static int epf_ntb_configure_mw(struct epf_ntb *ntb, u32 mw)
+{
+	phys_addr_t phys_addr;
+	u8 func_no, vfunc_no;
+	u64 addr, size;
+	int ret = 0;
+
+	phys_addr = ntb->vpci_mw_phy[mw];
+	addr = ntb->reg->addr;
+	size = ntb->reg->size;
+
+	func_no = ntb->epf->func_no;
+	vfunc_no = ntb->epf->vfunc_no;
+
+	ret = pci_epc_map_addr(ntb->epf->epc, func_no, vfunc_no, phys_addr, addr, size);
+	if (ret)
+		dev_err(&ntb->epf->epc->dev,
+			"Failed to map memory window %d address\n", mw);
+	return ret;
+}
+
+/**
+ * epf_ntb_teardown_mw() - Teardown the configured OB ATU
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ * @mw: Index of the memory window (either 0, 1, 2 or 3)
+ *
+ * Teardown the configured OB ATU configured in epf_ntb_configure_mw() using
+ * pci_epc_unmap_addr()
+ */
+static void epf_ntb_teardown_mw(struct epf_ntb *ntb, u32 mw)
+{
+	pci_epc_unmap_addr(ntb->epf->epc,
+			   ntb->epf->func_no,
+			   ntb->epf->vfunc_no,
+			   ntb->vpci_mw_phy[mw]);
+}
+
+/**
+ * epf_ntb_cmd_handler() - Handle commands provided by the NTB Host
+ * @work: work_struct for the epf_ntb_epc
+ *
+ * Workqueue function that gets invoked for the two epf_ntb_epc
+ * periodically (once every 5ms) to see if it has received any commands
+ * from NTB host. The host can send commands to configure doorbell or
+ * configure memory window or to update link status.
+ */
+static void epf_ntb_cmd_handler(struct work_struct *work)
+{
+	struct epf_ntb_ctrl *ctrl;
+	u32 command, argument;
+	struct epf_ntb *ntb;
+	struct device *dev;
+	int ret;
+	int i;
+
+	ntb = container_of(work, struct epf_ntb, cmd_handler.work);
+
+	for (i = 1; i < ntb->db_count; i++) {
+		if (readl(ntb->epf_db + i * 4)) {
+			if (readl(ntb->epf_db + i * 4))
+				ntb->db |= 1 << (i - 1);
+
+			ntb_db_event(&ntb->ntb, i);
+			writel(0, ntb->epf_db + i * 4);
+		}
+	}
+
+	ctrl = ntb->reg;
+	command = ctrl->command;
+	if (!command)
+		goto reset_handler;
+	argument = ctrl->argument;
+
+	ctrl->command = 0;
+	ctrl->argument = 0;
+
+	ctrl = ntb->reg;
+	dev = &ntb->epf->dev;
+
+	switch (command) {
+	case COMMAND_CONFIGURE_DOORBELL:
+		ctrl->command_status = COMMAND_STATUS_OK;
+		break;
+	case COMMAND_TEARDOWN_DOORBELL:
+		ctrl->command_status = COMMAND_STATUS_OK;
+		break;
+	case COMMAND_CONFIGURE_MW:
+		ret = epf_ntb_configure_mw(ntb, argument);
+		if (ret < 0)
+			ctrl->command_status = COMMAND_STATUS_ERROR;
+		else
+			ctrl->command_status = COMMAND_STATUS_OK;
+		break;
+	case COMMAND_TEARDOWN_MW:
+		epf_ntb_teardown_mw(ntb, argument);
+		ctrl->command_status = COMMAND_STATUS_OK;
+		break;
+	case COMMAND_LINK_UP:
+		ntb->linkup = true;
+		ret = epf_ntb_link_up(ntb, true);
+		if (ret < 0)
+			ctrl->command_status = COMMAND_STATUS_ERROR;
+		else
+			ctrl->command_status = COMMAND_STATUS_OK;
+		goto reset_handler;
+	case COMMAND_LINK_DOWN:
+		ntb->linkup = false;
+		ret = epf_ntb_link_up(ntb, false);
+		if (ret < 0)
+			ctrl->command_status = COMMAND_STATUS_ERROR;
+		else
+			ctrl->command_status = COMMAND_STATUS_OK;
+		break;
+	default:
+		dev_err(dev, "UNKNOWN command: %d\n", command);
+		break;
+	}
+
+reset_handler:
+	queue_delayed_work(kpcintb_workqueue, &ntb->cmd_handler,
+			   msecs_to_jiffies(5));
+}
+
+/**
+ * epf_ntb_config_sspad_bar_clear() - Clear Config + Self scratchpad BAR
+ * @ntb_epc: EPC associated with one of the HOST which holds peer's outbound
+ *	     address.
+ *
+ * Clear BAR0 of EP CONTROLLER 1 which contains the HOST1's config and
+ * self scratchpad region (removes inbound ATU configuration). While BAR0 is
+ * the default self scratchpad BAR, an NTB could have other BARs for self
+ * scratchpad (because of reserved BARs). This function can get the exact BAR
+ * used for self scratchpad from epf_ntb_bar[BAR_CONFIG].
+ *
+ * Please note the self scratchpad region and config region is combined to
+ * a single region and mapped using the same BAR. Also note HOST2's peer
+ * scratchpad is HOST1's self scratchpad.
+ */
+static void epf_ntb_config_sspad_bar_clear(struct epf_ntb *ntb)
+{
+	struct pci_epf_bar *epf_bar;
+	enum pci_barno barno;
+
+	barno = ntb->epf_ntb_bar[BAR_CONFIG];
+	epf_bar = &ntb->epf->bar[barno];
+
+	pci_epc_clear_bar(ntb->epf->epc, ntb->epf->func_no, ntb->epf->vfunc_no, epf_bar);
+}
+
+/**
+ * epf_ntb_config_sspad_bar_set() - Set Config + Self scratchpad BAR
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ *
+ * Map BAR0 of EP CONTROLLER 1 which contains the HOST1's config and
+ * self scratchpad region.
+ *
+ * Please note the self scratchpad region and config region is combined to
+ * a single region and mapped using the same BAR.
+ */
+static int epf_ntb_config_sspad_bar_set(struct epf_ntb *ntb)
+{
+	struct pci_epf_bar *epf_bar;
+	enum pci_barno barno;
+	u8 func_no, vfunc_no;
+	struct device *dev;
+	int ret;
+
+	dev = &ntb->epf->dev;
+	func_no = ntb->epf->func_no;
+	vfunc_no = ntb->epf->vfunc_no;
+	barno = ntb->epf_ntb_bar[BAR_CONFIG];
+	epf_bar = &ntb->epf->bar[barno];
+
+	ret = pci_epc_set_bar(ntb->epf->epc, func_no, vfunc_no, epf_bar);
+	if (ret) {
+		dev_err(dev, "inft: Config/Status/SPAD BAR set failed\n");
+		return ret;
+	}
+	return 0;
+}
+
+/**
+ * epf_ntb_config_spad_bar_free() - Free the physical memory associated with
+ *   config + scratchpad region
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ */
+static void epf_ntb_config_spad_bar_free(struct epf_ntb *ntb)
+{
+	enum pci_barno barno;
+
+	barno = ntb->epf_ntb_bar[BAR_CONFIG];
+	pci_epf_free_space(ntb->epf, ntb->reg, barno, 0);
+}
+
+/**
+ * epf_ntb_config_spad_bar_alloc() - Allocate memory for config + scratchpad
+ *   region
+ * @ntb: NTB device that facilitates communication between HOST1 and HOST2
+ *
+ * Allocate the Local Memory mentioned in the above diagram. The size of
+ * CONFIG REGION is sizeof(struct epf_ntb_ctrl) and size of SCRATCHPAD REGION
+ * is obtained from "spad-count" configfs entry.
+ */
+static int epf_ntb_config_spad_bar_alloc(struct epf_ntb *ntb)
+{
+	size_t align;
+	enum pci_barno barno;
+	struct epf_ntb_ctrl *ctrl;
+	u32 spad_size, ctrl_size;
+	u64 size;
+	struct pci_epf *epf = ntb->epf;
+	struct device *dev = &epf->dev;
+	u32 spad_count;
+	void *base;
+	int i;
+	const struct pci_epc_features *epc_features = pci_epc_get_features(epf->epc,
+								epf->func_no,
+								epf->vfunc_no);
+	barno = ntb->epf_ntb_bar[BAR_CONFIG];
+	size = epc_features->bar_fixed_size[barno];
+	align = epc_features->align;
+
+	if ((!IS_ALIGNED(size, align)))
+		return -EINVAL;
+
+	spad_count = ntb->spad_count;
+
+	ctrl_size = sizeof(struct epf_ntb_ctrl);
+	spad_size = 2 * spad_count * 4;
+
+	if (!align) {
+		ctrl_size = roundup_pow_of_two(ctrl_size);
+		spad_size = roundup_pow_of_two(spad_size);
+	} else {
+		ctrl_size = ALIGN(ctrl_size, align);
+		spad_size = ALIGN(spad_size, align);
+	}
+
+	if (!size)
+		size = ctrl_size + spad_size;
+	else if (size < ctrl_size + spad_size)
+		return -EINVAL;
+
+	base = pci_epf_alloc_space(epf, size, barno, align, 0);
+	if (!base) {
+		dev_err(dev, "Config/Status/SPAD alloc region fail\n");
+		return -ENOMEM;
+	}
+
+	ntb->reg = base;
+
+	ctrl = ntb->reg;
+	ctrl->spad_offset = ctrl_size;
+
+	ctrl->spad_count = spad_count;
+	ctrl->num_mws = ntb->num_mws;
+	ntb->spad_size = spad_size;
+
+	ctrl->db_entry_size = 4;
+
+	for (i = 0; i < ntb->db_count; i++) {
+		ntb->reg->db_data[i] = 1 + i;
+		ntb->reg->db_offset[i] = 0;
+	}
+
+	return 0;
+}
+
+/**
+ * epf_ntb_configure_interrupt() - Configure MSI/MSI-X capaiblity
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ *
+ * Configure MSI/MSI-X capability for each interface with number of
+ * interrupts equal to "db_count" configfs entry.
+ */
+static int epf_ntb_configure_interrupt(struct epf_ntb *ntb)
+{
+	const struct pci_epc_features *epc_features;
+	struct device *dev;
+	u32 db_count;
+	int ret;
+
+	dev = &ntb->epf->dev;
+
+	epc_features = pci_epc_get_features(ntb->epf->epc, ntb->epf->func_no, ntb->epf->vfunc_no);
+
+	if (!(epc_features->msix_capable || epc_features->msi_capable)) {
+		dev_err(dev, "MSI or MSI-X is required for doorbell\n");
+		return -EINVAL;
+	}
+
+	db_count = ntb->db_count;
+	if (db_count > MAX_DB_COUNT) {
+		dev_err(dev, "DB count cannot be more than %d\n", MAX_DB_COUNT);
+		return -EINVAL;
+	}
+
+	ntb->db_count = db_count;
+
+	if (epc_features->msi_capable) {
+		ret = pci_epc_set_msi(ntb->epf->epc,
+				      ntb->epf->func_no,
+				      ntb->epf->vfunc_no,
+				      16);
+		if (ret) {
+			dev_err(dev, "MSI configuration failed\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * epf_ntb_db_bar_init() - Configure Doorbell window BARs
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ */
+static int epf_ntb_db_bar_init(struct epf_ntb *ntb)
+{
+	const struct pci_epc_features *epc_features;
+	u32 align;
+	struct device *dev = &ntb->epf->dev;
+	int ret;
+	struct pci_epf_bar *epf_bar;
+	void __iomem *mw_addr;
+	enum pci_barno barno;
+	size_t size = 4 * ntb->db_count;
+
+	epc_features = pci_epc_get_features(ntb->epf->epc,
+					    ntb->epf->func_no,
+					    ntb->epf->vfunc_no);
+	align = epc_features->align;
+
+	if (size < 128)
+		size = 128;
+
+	if (align)
+		size = ALIGN(size, align);
+	else
+		size = roundup_pow_of_two(size);
+
+	barno = ntb->epf_ntb_bar[BAR_DB];
+
+	mw_addr = pci_epf_alloc_space(ntb->epf, size, barno, align, 0);
+	if (!mw_addr) {
+		dev_err(dev, "Failed to allocate OB address\n");
+		return -ENOMEM;
+	}
+
+	ntb->epf_db = mw_addr;
+
+	epf_bar = &ntb->epf->bar[barno];
+
+	ret = pci_epc_set_bar(ntb->epf->epc, ntb->epf->func_no, ntb->epf->vfunc_no, epf_bar);
+	if (ret) {
+		dev_err(dev, "Doorbell BAR set failed\n");
+			goto err_alloc_peer_mem;
+	}
+	return ret;
+
+err_alloc_peer_mem:
+	pci_epc_mem_free_addr(ntb->epf->epc, epf_bar->phys_addr, mw_addr, epf_bar->size);
+	return -1;
+}
+
+/**
+ * epf_ntb_db_bar_clear() - Clear doorbell BAR and free memory
+ *   allocated in peer's outbound address space
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ */
+static void epf_ntb_db_bar_clear(struct epf_ntb *ntb)
+{
+	enum pci_barno barno;
+
+	barno = ntb->epf_ntb_bar[BAR_DB];
+	pci_epf_free_space(ntb->epf, ntb->epf_db, barno, 0);
+	pci_epc_clear_bar(ntb->epf->epc,
+			  ntb->epf->func_no,
+			  ntb->epf->vfunc_no,
+			  &ntb->epf->bar[barno]);
+}
+
+/**
+ * epf_ntb_mw_bar_init() - Configure Memory window BARs
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ *
+ */
+static int epf_ntb_mw_bar_init(struct epf_ntb *ntb)
+{
+	int ret = 0;
+	int i;
+	u64 size;
+	enum pci_barno barno;
+	struct device *dev = &ntb->epf->dev;
+
+	for (i = 0; i < ntb->num_mws; i++) {
+		size = ntb->mws_size[i];
+		barno = ntb->epf_ntb_bar[BAR_MW0 + i];
+
+		ntb->epf->bar[barno].barno = barno;
+		ntb->epf->bar[barno].size = size;
+		ntb->epf->bar[barno].addr = 0;
+		ntb->epf->bar[barno].phys_addr = 0;
+		ntb->epf->bar[barno].flags |= upper_32_bits(size) ?
+				PCI_BASE_ADDRESS_MEM_TYPE_64 :
+				PCI_BASE_ADDRESS_MEM_TYPE_32;
+
+		ret = pci_epc_set_bar(ntb->epf->epc,
+				      ntb->epf->func_no,
+				      ntb->epf->vfunc_no,
+				      &ntb->epf->bar[barno]);
+		if (ret) {
+			dev_err(dev, "MW set failed\n");
+			goto err_alloc_mem;
+		}
+
+		/* Allocate EPC outbound memory windows to vpci vntb device */
+		ntb->vpci_mw_addr[i] = pci_epc_mem_alloc_addr(ntb->epf->epc,
+							      &ntb->vpci_mw_phy[i],
+							      size);
+		if (!ntb->vpci_mw_addr[i]) {
+			dev_err(dev, "Failed to allocate source address\n");
+			goto err_alloc_mem;
+		}
+	}
+
+	return ret;
+err_alloc_mem:
+	return ret;
+}
+
+/**
+ * epf_ntb_mw_bar_clear() - Clear Memory window BARs
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ */
+static void epf_ntb_mw_bar_clear(struct epf_ntb *ntb)
+{
+	enum pci_barno barno;
+	int i;
+
+	for (i = 0; i < ntb->num_mws; i++) {
+		barno = ntb->epf_ntb_bar[BAR_MW0 + i];
+		pci_epc_clear_bar(ntb->epf->epc,
+				  ntb->epf->func_no,
+				  ntb->epf->vfunc_no,
+				  &ntb->epf->bar[barno]);
+
+		pci_epc_mem_free_addr(ntb->epf->epc,
+				      ntb->vpci_mw_phy[i],
+				      ntb->vpci_mw_addr[i],
+				      ntb->mws_size[i]);
+	}
+}
+
+/**
+ * epf_ntb_epc_destroy() - Cleanup NTB EPC interface
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ *
+ * Wrapper for epf_ntb_epc_destroy_interface() to cleanup all the NTB interfaces
+ */
+static void epf_ntb_epc_destroy(struct epf_ntb *ntb)
+{
+	pci_epc_remove_epf(ntb->epf->epc, ntb->epf, 0);
+	pci_epc_put(ntb->epf->epc);
+}
+
+/**
+ * epf_ntb_init_epc_bar() - Identify BARs to be used for each of the NTB
+ * constructs (scratchpad region, doorbell, memorywindow)
+ * @ntb: NTB device that facilitates communication between HOST and vHOST
+ */
+static int epf_ntb_init_epc_bar(struct epf_ntb *ntb)
+{
+	const struct pci_epc_features *epc_features;
+	enum pci_barno barno;
+	enum epf_ntb_bar bar;
+	struct device *dev;
+	u32 num_mws;
+	int i;
+
+	barno = BAR_0;
+	num_mws = ntb->num_mws;
+	dev = &ntb->epf->dev;
+	epc_features = pci_epc_get_features(ntb->epf->epc, ntb->epf->func_no, ntb->epf->vfunc_no);
+
+	/* These are required BARs which are mandatory for NTB functionality */
+	for (bar = BAR_CONFIG; bar <= BAR_MW0; bar++, barno++) {
+		barno = pci_epc_get_next_free_bar(epc_features, barno);
+		if (barno < 0) {
+			dev_err(dev, "Fail to get NTB function BAR\n");
+			return barno;
+		}
+		ntb->epf_ntb_bar[bar] = barno;
+	}
+
+	/* These are optional BARs which don't impact NTB functionality */
+	for (bar = BAR_MW1, i = 1; i < num_mws; bar++, barno++, i++) {
+		barno = pci_epc_get_next_free_bar(epc_features, barno);
+		if (barno < 0) {
+			ntb->num_mws = i;
+			dev_dbg(dev, "BAR not available for > MW%d\n", i + 1);
+		}
+		ntb->epf_ntb_bar[bar] = barno;
+	}
+
+	return 0;
+}
+
+/**
+ * epf_ntb_epc_init() - Initialize NTB interface
+ * @ntb: NTB device that facilitates communication between HOST and vHOST2
+ *
+ * Wrapper to initialize a particular EPC interface and start the workqueue
+ * to check for commands from host. This function will write to the
+ * EP controller HW for configuring it.
+ */
+static int epf_ntb_epc_init(struct epf_ntb *ntb)
+{
+	u8 func_no, vfunc_no;
+	struct pci_epc *epc;
+	struct pci_epf *epf;
+	struct device *dev;
+	int ret;
+
+	epf = ntb->epf;
+	dev = &epf->dev;
+	epc = epf->epc;
+	func_no = ntb->epf->func_no;
+	vfunc_no = ntb->epf->vfunc_no;
+
+	ret = epf_ntb_config_sspad_bar_set(ntb);
+	if (ret) {
+		dev_err(dev, "Config/self SPAD BAR init failed");
+		return ret;
+	}
+
+	ret = epf_ntb_configure_interrupt(ntb);
+	if (ret) {
+		dev_err(dev, "Interrupt configuration failed\n");
+		goto err_config_interrupt;
+	}
+
+	ret = epf_ntb_db_bar_init(ntb);
+	if (ret) {
+		dev_err(dev, "DB BAR init failed\n");
+		goto err_db_bar_init;
+	}
+
+	ret = epf_ntb_mw_bar_init(ntb);
+	if (ret) {
+		dev_err(dev, "MW BAR init failed\n");
+		goto err_mw_bar_init;
+	}
+
+	if (vfunc_no <= 1) {
+		ret = pci_epc_write_header(epc, func_no, vfunc_no, epf->header);
+		if (ret) {
+			dev_err(dev, "Configuration header write failed\n");
+			goto err_write_header;
+		}
+	}
+
+	INIT_DELAYED_WORK(&ntb->cmd_handler, epf_ntb_cmd_handler);
+	queue_work(kpcintb_workqueue, &ntb->cmd_handler.work);
+
+	return 0;
+
+err_write_header:
+	epf_ntb_mw_bar_clear(ntb);
+err_mw_bar_init:
+	epf_ntb_db_bar_clear(ntb);
+err_db_bar_init:
+err_config_interrupt:
+	epf_ntb_config_sspad_bar_clear(ntb);
+
+	return ret;
+}
+
+
+/**
+ * epf_ntb_epc_cleanup() - Cleanup all NTB interfaces
+ * @ntb: NTB device that facilitates communication between HOST1 and HOST2
+ *
+ * Wrapper to cleanup all NTB interfaces.
+ */
+static void epf_ntb_epc_cleanup(struct epf_ntb *ntb)
+{
+	epf_ntb_db_bar_clear(ntb);
+	epf_ntb_mw_bar_clear(ntb);
+}
+
+#define EPF_NTB_R(_name)						\
+static ssize_t epf_ntb_##_name##_show(struct config_item *item,		\
+				      char *page)			\
+{									\
+	struct config_group *group = to_config_group(item);		\
+	struct epf_ntb *ntb = to_epf_ntb(group);			\
+									\
+	return sprintf(page, "%d\n", ntb->_name);			\
+}
+
+#define EPF_NTB_W(_name)						\
+static ssize_t epf_ntb_##_name##_store(struct config_item *item,	\
+				       const char *page, size_t len)	\
+{									\
+	struct config_group *group = to_config_group(item);		\
+	struct epf_ntb *ntb = to_epf_ntb(group);			\
+	u32 val;							\
+	int ret;							\
+									\
+	ret = kstrtou32(page, 0, &val);					\
+	if (ret)							\
+		return ret;						\
+									\
+	ntb->_name = val;						\
+									\
+	return len;							\
+}
+
+#define EPF_NTB_MW_R(_name)						\
+static ssize_t epf_ntb_##_name##_show(struct config_item *item,		\
+				      char *page)			\
+{									\
+	struct config_group *group = to_config_group(item);		\
+	struct epf_ntb *ntb = to_epf_ntb(group);			\
+	int win_no;							\
+									\
+	sscanf(#_name, "mw%d", &win_no);				\
+									\
+	return sprintf(page, "%lld\n", ntb->mws_size[win_no - 1]);	\
+}
+
+#define EPF_NTB_MW_W(_name)						\
+static ssize_t epf_ntb_##_name##_store(struct config_item *item,	\
+				       const char *page, size_t len)	\
+{									\
+	struct config_group *group = to_config_group(item);		\
+	struct epf_ntb *ntb = to_epf_ntb(group);			\
+	struct device *dev = &ntb->epf->dev;				\
+	int win_no;							\
+	u64 val;							\
+	int ret;							\
+									\
+	ret = kstrtou64(page, 0, &val);					\
+	if (ret)							\
+		return ret;						\
+									\
+	if (sscanf(#_name, "mw%d", &win_no) != 1)			\
+		return -EINVAL;						\
+									\
+	if (ntb->num_mws < win_no) {					\
+		dev_err(dev, "Invalid num_nws: %d value\n", ntb->num_mws); \
+		return -EINVAL;						\
+	}								\
+									\
+	ntb->mws_size[win_no - 1] = val;				\
+									\
+	return len;							\
+}
+
+static ssize_t epf_ntb_num_mws_store(struct config_item *item,
+				     const char *page, size_t len)
+{
+	struct config_group *group = to_config_group(item);
+	struct epf_ntb *ntb = to_epf_ntb(group);
+	u32 val;
+	int ret;
+
+	ret = kstrtou32(page, 0, &val);
+	if (ret)
+		return ret;
+
+	if (val > MAX_MW)
+		return -EINVAL;
+
+	ntb->num_mws = val;
+
+	return len;
+}
+
+EPF_NTB_R(spad_count)
+EPF_NTB_W(spad_count)
+EPF_NTB_R(db_count)
+EPF_NTB_W(db_count)
+EPF_NTB_R(num_mws)
+EPF_NTB_R(vbus_number)
+EPF_NTB_W(vbus_number)
+EPF_NTB_R(vntb_pid)
+EPF_NTB_W(vntb_pid)
+EPF_NTB_R(vntb_vid)
+EPF_NTB_W(vntb_vid)
+EPF_NTB_MW_R(mw1)
+EPF_NTB_MW_W(mw1)
+EPF_NTB_MW_R(mw2)
+EPF_NTB_MW_W(mw2)
+EPF_NTB_MW_R(mw3)
+EPF_NTB_MW_W(mw3)
+EPF_NTB_MW_R(mw4)
+EPF_NTB_MW_W(mw4)
+
+CONFIGFS_ATTR(epf_ntb_, spad_count);
+CONFIGFS_ATTR(epf_ntb_, db_count);
+CONFIGFS_ATTR(epf_ntb_, num_mws);
+CONFIGFS_ATTR(epf_ntb_, mw1);
+CONFIGFS_ATTR(epf_ntb_, mw2);
+CONFIGFS_ATTR(epf_ntb_, mw3);
+CONFIGFS_ATTR(epf_ntb_, mw4);
+CONFIGFS_ATTR(epf_ntb_, vbus_number);
+CONFIGFS_ATTR(epf_ntb_, vntb_pid);
+CONFIGFS_ATTR(epf_ntb_, vntb_vid);
+
+static struct configfs_attribute *epf_ntb_attrs[] = {
+	&epf_ntb_attr_spad_count,
+	&epf_ntb_attr_db_count,
+	&epf_ntb_attr_num_mws,
+	&epf_ntb_attr_mw1,
+	&epf_ntb_attr_mw2,
+	&epf_ntb_attr_mw3,
+	&epf_ntb_attr_mw4,
+	&epf_ntb_attr_vbus_number,
+	&epf_ntb_attr_vntb_pid,
+	&epf_ntb_attr_vntb_vid,
+	NULL,
+};
+
+static const struct config_item_type ntb_group_type = {
+	.ct_attrs	= epf_ntb_attrs,
+	.ct_owner	= THIS_MODULE,
+};
+
+/**
+ * epf_ntb_add_cfs() - Add configfs directory specific to NTB
+ * @epf: NTB endpoint function device
+ * @group: A pointer to the config_group structure referencing a group of
+ *	   config_items of a specific type that belong to a specific sub-system.
+ *
+ * Add configfs directory specific to NTB. This directory will hold
+ * NTB specific properties like db_count, spad_count, num_mws etc.,
+ */
+static struct config_group *epf_ntb_add_cfs(struct pci_epf *epf,
+					    struct config_group *group)
+{
+	struct epf_ntb *ntb = epf_get_drvdata(epf);
+	struct config_group *ntb_group = &ntb->group;
+	struct device *dev = &epf->dev;
+
+	config_group_init_type_name(ntb_group, dev_name(dev), &ntb_group_type);
+
+	return ntb_group;
+}
+
+/*==== virtual PCI bus driver, which only load virtual NTB PCI driver ====*/
+
+static u32 pci_space[] = {
+	0xffffffff,	/*DeviceID, Vendor ID*/
+	0,		/*Status, Command*/
+	0xffffffff,	/*Class code, subclass, prog if, revision id*/
+	0x40,		/*bist, header type, latency Timer, cache line size*/
+	0,		/*BAR 0*/
+	0,		/*BAR 1*/
+	0,		/*BAR 2*/
+	0,		/*BAR 3*/
+	0,		/*BAR 4*/
+	0,		/*BAR 5*/
+	0,		/*Cardbus cis point*/
+	0,		/*Subsystem ID Subystem vendor id*/
+	0,		/*ROM Base Address*/
+	0,		/*Reserved, Cap. Point*/
+	0,		/*Reserved,*/
+	0,		/*Max Lat, Min Gnt, interrupt pin, interrupt line*/
+};
+
+int pci_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *val)
+{
+	if (devfn == 0) {
+		memcpy(val, ((u8 *)pci_space) + where, size);
+		return PCIBIOS_SUCCESSFUL;
+	}
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+int pci_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 val)
+{
+	return 0;
+}
+
+struct pci_ops vpci_ops = {
+	.read = pci_read,
+	.write = pci_write,
+};
+
+static int vpci_scan_bus(void *sysdata)
+{
+	struct pci_bus *vpci_bus;
+	struct epf_ntb *ndev = sysdata;
+
+	vpci_bus = pci_scan_bus(ndev->vbus_number, &vpci_ops, sysdata);
+	if (!vpci_bus) {
+		pr_err("create pci bus failed\n");
+		return -EINVAL;
+	}
+
+	pci_bus_add_devices(vpci_bus);
+
+	return 0;
+}
+
+/*==================== Virtual PCIe NTB driver ==========================*/
+
+static int vntb_epf_mw_count(struct ntb_dev *ntb, int pidx)
+{
+	struct epf_ntb *ndev = ntb_ndev(ntb);
+
+	return ndev->num_mws;
+}
+
+static int vntb_epf_spad_count(struct ntb_dev *ntb)
+{
+	return ntb_ndev(ntb)->spad_count;
+}
+
+static int vntb_epf_peer_mw_count(struct ntb_dev *ntb)
+{
+	return ntb_ndev(ntb)->num_mws;
+}
+
+static u64 vntb_epf_db_valid_mask(struct ntb_dev *ntb)
+{
+	return BIT_ULL(ntb_ndev(ntb)->db_count) - 1;
+}
+
+static int vntb_epf_db_set_mask(struct ntb_dev *ntb, u64 db_bits)
+{
+	return 0;
+}
+
+static int vntb_epf_mw_set_trans(struct ntb_dev *ndev, int pidx, int idx,
+		dma_addr_t addr, resource_size_t size)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+	struct pci_epf_bar *epf_bar;
+	enum pci_barno barno;
+	int ret;
+	struct device *dev;
+
+	dev = &ntb->ntb.dev;
+	barno = ntb->epf_ntb_bar[BAR_MW0 + idx];
+	epf_bar = &ntb->epf->bar[barno];
+	epf_bar->phys_addr = addr;
+	epf_bar->barno = barno;
+	epf_bar->size = size;
+
+	ret = pci_epc_set_bar(ntb->epf->epc, 0, 0, epf_bar);
+	if (ret) {
+		dev_err(dev, "failure set mw trans\n");
+		return ret;
+	}
+	return 0;
+}
+
+static int vntb_epf_mw_clear_trans(struct ntb_dev *ntb, int pidx, int idx)
+{
+	return 0;
+}
+
+static int vntb_epf_peer_mw_get_addr(struct ntb_dev *ndev, int idx,
+				phys_addr_t *base, resource_size_t *size)
+{
+
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+
+	if (base)
+		*base = ntb->vpci_mw_phy[idx];
+
+	if (size)
+		*size = ntb->mws_size[idx];
+
+	return 0;
+}
+
+static int vntb_epf_link_enable(struct ntb_dev *ntb,
+			enum ntb_speed max_speed,
+			enum ntb_width max_width)
+{
+	return 0;
+}
+
+static u32 vntb_epf_spad_read(struct ntb_dev *ndev, int idx)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+	int off = ntb->reg->spad_offset, ct = ntb->reg->spad_count * 4;
+	u32 val;
+	void __iomem *base = ntb->reg;
+
+	val = readl(base + off + ct + idx * 4);
+	return val;
+}
+
+static int vntb_epf_spad_write(struct ntb_dev *ndev, int idx, u32 val)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+	struct epf_ntb_ctrl *ctrl = ntb->reg;
+	int off = ctrl->spad_offset, ct = ctrl->spad_count * 4;
+	void __iomem *base = ntb->reg;
+
+	writel(val, base + off + ct + idx * 4);
+	return 0;
+}
+
+static u32 vntb_epf_peer_spad_read(struct ntb_dev *ndev, int pidx, int idx)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+	struct epf_ntb_ctrl *ctrl = ntb->reg;
+	int off = ctrl->spad_offset;
+	void __iomem *base = ntb->reg;
+	u32 val;
+
+	val = readl(base + off + idx * 4);
+	return val;
+}
+
+static int vntb_epf_peer_spad_write(struct ntb_dev *ndev, int pidx, int idx, u32 val)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+	struct epf_ntb_ctrl *ctrl = ntb->reg;
+	int off = ctrl->spad_offset;
+	void __iomem *base = ntb->reg;
+
+	writel(val, base + off + idx * 4);
+	return 0;
+}
+
+static int vntb_epf_peer_db_set(struct ntb_dev *ndev, u64 db_bits)
+{
+	u32 interrupt_num = ffs(db_bits) + 1;
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+	u8 func_no, vfunc_no;
+	int ret;
+
+	func_no = ntb->epf->func_no;
+	vfunc_no = ntb->epf->vfunc_no;
+
+	ret = pci_epc_raise_irq(ntb->epf->epc,
+				func_no,
+				vfunc_no,
+				PCI_EPC_IRQ_MSI,
+				interrupt_num + 1);
+	if (ret)
+		dev_err(&ntb->ntb.dev, "Failed to raise IRQ\n");
+
+	return ret;
+}
+
+static u64 vntb_epf_db_read(struct ntb_dev *ndev)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+
+	return ntb->db;
+}
+
+static int vntb_epf_mw_get_align(struct ntb_dev *ndev, int pidx, int idx,
+			resource_size_t *addr_align,
+			resource_size_t *size_align,
+			resource_size_t *size_max)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+
+	if (addr_align)
+		*addr_align = SZ_4K;
+
+	if (size_align)
+		*size_align = 1;
+
+	if (size_max)
+		*size_max = ntb->mws_size[idx];
+
+	return 0;
+}
+
+static u64 vntb_epf_link_is_up(struct ntb_dev *ndev,
+			enum ntb_speed *speed,
+			enum ntb_width *width)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+
+	return ntb->reg->link_status;
+}
+
+static int vntb_epf_db_clear_mask(struct ntb_dev *ndev, u64 db_bits)
+{
+	return 0;
+}
+
+static int vntb_epf_db_clear(struct ntb_dev *ndev, u64 db_bits)
+{
+	struct epf_ntb *ntb = ntb_ndev(ndev);
+
+	ntb->db &= ~db_bits;
+	return 0;
+}
+
+static int vntb_epf_link_disable(struct ntb_dev *ntb)
+{
+	return 0;
+}
+
+static const struct ntb_dev_ops vntb_epf_ops = {
+	.mw_count		= vntb_epf_mw_count,
+	.spad_count		= vntb_epf_spad_count,
+	.peer_mw_count		= vntb_epf_peer_mw_count,
+	.db_valid_mask		= vntb_epf_db_valid_mask,
+	.db_set_mask		= vntb_epf_db_set_mask,
+	.mw_set_trans		= vntb_epf_mw_set_trans,
+	.mw_clear_trans		= vntb_epf_mw_clear_trans,
+	.peer_mw_get_addr	= vntb_epf_peer_mw_get_addr,
+	.link_enable		= vntb_epf_link_enable,
+	.spad_read		= vntb_epf_spad_read,
+	.spad_write		= vntb_epf_spad_write,
+	.peer_spad_read		= vntb_epf_peer_spad_read,
+	.peer_spad_write	= vntb_epf_peer_spad_write,
+	.peer_db_set		= vntb_epf_peer_db_set,
+	.db_read		= vntb_epf_db_read,
+	.mw_get_align		= vntb_epf_mw_get_align,
+	.link_is_up		= vntb_epf_link_is_up,
+	.db_clear_mask		= vntb_epf_db_clear_mask,
+	.db_clear		= vntb_epf_db_clear,
+	.link_disable		= vntb_epf_link_disable,
+};
+
+static int pci_vntb_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	int ret;
+	struct epf_ntb *ndev = (struct epf_ntb *)pdev->sysdata;
+	struct device *dev = &pdev->dev;
+
+	ndev->ntb.pdev = pdev;
+	ndev->ntb.topo = NTB_TOPO_NONE;
+	ndev->ntb.ops =  &vntb_epf_ops;
+
+	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(dev, "Cannot set DMA mask\n");
+		return -EINVAL;
+	}
+
+	ret = ntb_register_device(&ndev->ntb);
+	if (ret) {
+		dev_err(dev, "Failed to register NTB device\n");
+		return ret;
+	}
+
+	dev_dbg(dev, "PCI Virtual NTB driver loaded\n");
+	return 0;
+}
+
+static struct pci_device_id pci_vntb_table[] = {
+	{
+		PCI_DEVICE(0xffff, 0xffff),
+	},
+	{},
+};
+
+static struct pci_driver vntb_pci_driver = {
+	.name           = "pci-vntb",
+	.id_table       = pci_vntb_table,
+	.probe          = pci_vntb_probe,
+};
+
+/* ============ PCIe EPF Driver Bind ====================*/
+
+/**
+ * epf_ntb_bind() - Initialize endpoint controller to provide NTB functionality
+ * @epf: NTB endpoint function device
+ *
+ * Initialize both the endpoint controllers associated with NTB function device.
+ * Invoked when a primary interface or secondary interface is bound to EPC
+ * device. This function will succeed only when EPC is bound to both the
+ * interfaces.
+ */
+static int epf_ntb_bind(struct pci_epf *epf)
+{
+	struct epf_ntb *ntb = epf_get_drvdata(epf);
+	struct device *dev = &epf->dev;
+	int ret;
+
+	if (!epf->epc) {
+		dev_dbg(dev, "PRIMARY EPC interface not yet bound\n");
+		return 0;
+	}
+
+	ret = epf_ntb_init_epc_bar(ntb);
+	if (ret) {
+		dev_err(dev, "Failed to create NTB EPC\n");
+		goto err_bar_init;
+	}
+
+	ret = epf_ntb_config_spad_bar_alloc(ntb);
+	if (ret) {
+		dev_err(dev, "Failed to allocate BAR memory\n");
+		goto err_bar_alloc;
+	}
+
+	ret = epf_ntb_epc_init(ntb);
+	if (ret) {
+		dev_err(dev, "Failed to initialize EPC\n");
+		goto err_bar_alloc;
+	}
+
+	epf_set_drvdata(epf, ntb);
+
+	pci_space[0] = (ntb->vntb_pid << 16) | ntb->vntb_vid;
+	pci_vntb_table[0].vendor = ntb->vntb_vid;
+	pci_vntb_table[0].device = ntb->vntb_pid;
+
+	if (pci_register_driver(&vntb_pci_driver)) {
+		dev_err(dev, "failure register vntb pci driver\n");
+		goto err_bar_alloc;
+	}
+
+	ret = vpci_scan_bus(ntb);
+	if (ret)
+		goto err_unregister;
+
+	return 0;
+
+err_unregister:
+	pci_unregister_driver(&vntb_pci_driver);
+err_bar_alloc:
+	epf_ntb_config_spad_bar_free(ntb);
+
+err_bar_init:
+	epf_ntb_epc_destroy(ntb);
+
+	return ret;
+}
+
+/**
+ * epf_ntb_unbind() - Cleanup the initialization from epf_ntb_bind()
+ * @epf: NTB endpoint function device
+ *
+ * Cleanup the initialization from epf_ntb_bind()
+ */
+static void epf_ntb_unbind(struct pci_epf *epf)
+{
+	struct epf_ntb *ntb = epf_get_drvdata(epf);
+
+	epf_ntb_epc_cleanup(ntb);
+	epf_ntb_config_spad_bar_free(ntb);
+	epf_ntb_epc_destroy(ntb);
+
+	pci_unregister_driver(&vntb_pci_driver);
+}
+
+// EPF driver probe
+static struct pci_epf_ops epf_ntb_ops = {
+	.bind   = epf_ntb_bind,
+	.unbind = epf_ntb_unbind,
+	.add_cfs = epf_ntb_add_cfs,
+};
+
+/**
+ * epf_ntb_probe() - Probe NTB function driver
+ * @epf: NTB endpoint function device
+ *
+ * Probe NTB function driver when endpoint function bus detects a NTB
+ * endpoint function.
+ */
+static int epf_ntb_probe(struct pci_epf *epf)
+{
+	struct epf_ntb *ntb;
+	struct device *dev;
+
+	dev = &epf->dev;
+
+	ntb = devm_kzalloc(dev, sizeof(*ntb), GFP_KERNEL);
+	if (!ntb)
+		return -ENOMEM;
+
+	epf->header = &epf_ntb_header;
+	ntb->epf = epf;
+	ntb->vbus_number = 0xff;
+	epf_set_drvdata(epf, ntb);
+
+	dev_info(dev, "pci-ep epf driver loaded\n");
+	return 0;
+}
+
+static const struct pci_epf_device_id epf_ntb_ids[] = {
+	{
+		.name = "pci_epf_vntb",
+	},
+	{},
+};
+
+static struct pci_epf_driver epf_ntb_driver = {
+	.driver.name    = "pci_epf_vntb",
+	.probe          = epf_ntb_probe,
+	.id_table       = epf_ntb_ids,
+	.ops            = &epf_ntb_ops,
+	.owner          = THIS_MODULE,
+};
+
+static int __init epf_ntb_init(void)
+{
+	int ret;
+
+	kpcintb_workqueue = alloc_workqueue("kpcintb", WQ_MEM_RECLAIM |
+					    WQ_HIGHPRI, 0);
+	ret = pci_epf_register_driver(&epf_ntb_driver);
+	if (ret) {
+		destroy_workqueue(kpcintb_workqueue);
+		pr_err("Failed to register pci epf ntb driver --> %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+module_init(epf_ntb_init);
+
+static void __exit epf_ntb_exit(void)
+{
+	pci_epf_unregister_driver(&epf_ntb_driver);
+	destroy_workqueue(kpcintb_workqueue);
+}
+module_exit(epf_ntb_exit);
+
+MODULE_DESCRIPTION("PCI EPF NTB DRIVER");
+MODULE_AUTHOR("Frank Li <Frank.li@nxp.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/endpoint/pci-epc-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/endpoint/pci-epc-core.c
@@ -740,7 +740,7 @@
 {
 	int r;
 
-	r = devres_destroy(dev, devm_pci_epc_release, devm_pci_epc_match,
+	r = devres_release(dev, devm_pci_epc_release, devm_pci_epc_match,
 			   epc);
 	dev_WARN_ONCE(dev, r, "couldn't find PCI EPC resource\n");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/endpoint/pci-epf-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/endpoint/pci-epf-core.c
@@ -234,6 +234,7 @@
 
 	mutex_lock(&epf_pf->lock);
 	clear_bit(epf_vf->vfunc_no, &epf_pf->vfunction_num_map);
+	epf_vf->epf_pf = NULL;
 	list_del(&epf_vf->list);
 	mutex_unlock(&epf_pf->lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/cpqphp_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/cpqphp_pci.c
@@ -135,11 +135,13 @@
 static int PCI_RefinedAccessConfig(struct pci_bus *bus, unsigned int devfn, u8 offset, u32 *value)
 {
 	u32 vendID = 0;
+	int ret;
 
-	if (pci_bus_read_config_dword(bus, devfn, PCI_VENDOR_ID, &vendID) == -1)
-		return -1;
-	if (vendID == 0xffffffff)
-		return -1;
+	ret = pci_bus_read_config_dword(bus, devfn, PCI_VENDOR_ID, &vendID);
+	if (ret != PCIBIOS_SUCCESSFUL)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	if (PCI_POSSIBLE_ERROR(vendID))
+		return PCIBIOS_DEVICE_NOT_FOUND;
 	return pci_bus_read_config_dword(bus, devfn, offset, value);
 }
 
@@ -200,13 +202,15 @@
 {
 	u16 tdevice;
 	u32 work;
+	int ret;
 	u8 tbus;
 
 	ctrl->pci_bus->number = bus_num;
 
 	for (tdevice = 0; tdevice < 0xFF; tdevice++) {
 		/* Scan for access first */
-		if (PCI_RefinedAccessConfig(ctrl->pci_bus, tdevice, 0x08, &work) == -1)
+		ret = PCI_RefinedAccessConfig(ctrl->pci_bus, tdevice, 0x08, &work);
+		if (ret)
 			continue;
 		dbg("Looking for nonbridge bus_num %d dev_num %d\n", bus_num, tdevice);
 		/* Yep we got one. Not a bridge ? */
@@ -218,7 +222,8 @@
 	}
 	for (tdevice = 0; tdevice < 0xFF; tdevice++) {
 		/* Scan for access first */
-		if (PCI_RefinedAccessConfig(ctrl->pci_bus, tdevice, 0x08, &work) == -1)
+		ret = PCI_RefinedAccessConfig(ctrl->pci_bus, tdevice, 0x08, &work);
+		if (ret)
 			continue;
 		dbg("Looking for bridge bus_num %d dev_num %d\n", bus_num, tdevice);
 		/* Yep we got one. bridge ? */
@@ -251,7 +256,7 @@
 			*dev_num = tdevice;
 			ctrl->pci_bus->number = tbus;
 			pci_bus_read_config_dword(ctrl->pci_bus, *dev_num, PCI_VENDOR_ID, &work);
-			if (!nobridge || (work == 0xffffffff))
+			if (!nobridge || PCI_POSSIBLE_ERROR(work))
 				return 0;
 
 			dbg("bus_num %d devfn %d\n", *bus_num, *dev_num);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/pciehp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/pciehp.h
@@ -75,6 +75,8 @@
  * @reset_lock: prevents access to the Data Link Layer Link Active bit in the
  *	Link Status register and to the Presence Detect State bit in the Slot
  *	Status register during a slot reset which may cause them to flap
+ * @depth: Number of additional hotplug ports in the path to the root bus,
+ *	used as lock subclass for @reset_lock
  * @ist_running: flag to keep user request waiting while IRQ thread is running
  * @request_result: result of last user request submitted to the IRQ thread
  * @requester: wait queue to wake up on completion of user request,
@@ -106,6 +108,7 @@
 
 	struct hotplug_slot hotplug_slot;	/* hotplug core interface */
 	struct rw_semaphore reset_lock;
+	unsigned int depth;
 	unsigned int ist_running;
 	int request_result;
 	wait_queue_head_t requester;
@@ -189,6 +192,8 @@
 int pciehp_set_raw_indicator_status(struct hotplug_slot *h_slot, u8 status);
 int pciehp_get_raw_indicator_status(struct hotplug_slot *h_slot, u8 *status);
 
+int pciehp_slot_reset(struct pcie_device *dev);
+
 static inline const char *slot_name(struct controller *ctrl)
 {
 	return hotplug_slot_name(&ctrl->hotplug_slot);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/pciehp_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/pciehp_core.c
@@ -166,7 +166,7 @@
 {
 	int occupied;
 
-	down_read(&ctrl->reset_lock);
+	down_read_nested(&ctrl->reset_lock, ctrl->depth);
 	mutex_lock(&ctrl->state_lock);
 
 	occupied = pciehp_card_present_or_link_active(ctrl);
@@ -351,6 +351,8 @@
 	.runtime_suspend = pciehp_runtime_suspend,
 	.runtime_resume	= pciehp_runtime_resume,
 #endif	/* PM */
+
+	.slot_reset	= pciehp_slot_reset,
 };
 
 int __init pcie_hp_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/pciehp_ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/pciehp_ctrl.c
@@ -256,6 +256,14 @@
 	present = pciehp_card_present(ctrl);
 	link_active = pciehp_check_link_active(ctrl);
 	if (present <= 0 && link_active <= 0) {
+		if (ctrl->state == BLINKINGON_STATE) {
+			ctrl->state = OFF_STATE;
+			cancel_delayed_work(&ctrl->button_work);
+			pciehp_set_indicators(ctrl, PCI_EXP_SLTCTL_PWR_IND_OFF,
+					      INDICATOR_NOOP);
+			ctrl_info(ctrl, "Slot(%s): Card not present\n",
+				  slot_name(ctrl));
+		}
 		mutex_unlock(&ctrl->state_lock);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/pciehp_hpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/pciehp_hpc.c
@@ -98,6 +98,8 @@
 		if (slot_status & PCI_EXP_SLTSTA_CC) {
 			pcie_capability_write_word(pdev, PCI_EXP_SLTSTA,
 						   PCI_EXP_SLTSTA_CC);
+			ctrl->cmd_busy = 0;
+			smp_mb();
 			return 1;
 		}
 		msleep(10);
@@ -330,17 +332,11 @@
 static int __pciehp_link_set(struct controller *ctrl, bool enable)
 {
 	struct pci_dev *pdev = ctrl_dev(ctrl);
-	u16 lnk_ctrl;
 
-	pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &lnk_ctrl);
+	pcie_capability_clear_and_set_word(pdev, PCI_EXP_LNKCTL,
+					   PCI_EXP_LNKCTL_LD,
+					   enable ? 0 : PCI_EXP_LNKCTL_LD);
 
-	if (enable)
-		lnk_ctrl &= ~PCI_EXP_LNKCTL_LD;
-	else
-		lnk_ctrl |= PCI_EXP_LNKCTL_LD;
-
-	pcie_capability_write_word(pdev, PCI_EXP_LNKCTL, lnk_ctrl);
-	ctrl_dbg(ctrl, "%s: lnk_ctrl = %x\n", __func__, lnk_ctrl);
 	return 0;
 }
 
@@ -583,7 +579,7 @@
 	 * the corresponding link change may have been ignored above.
 	 * Synthesize it to ensure that it is acted on.
 	 */
-	down_read(&ctrl->reset_lock);
+	down_read_nested(&ctrl->reset_lock, ctrl->depth);
 	if (!pciehp_check_link_active(ctrl))
 		pciehp_request(ctrl, PCI_EXP_SLTSTA_DLLSC);
 	up_read(&ctrl->reset_lock);
@@ -642,6 +638,8 @@
 	 */
 	if (ctrl->power_fault_detected)
 		status &= ~PCI_EXP_SLTSTA_PFD;
+	else if (status & PCI_EXP_SLTSTA_PFD)
+		ctrl->power_fault_detected = true;
 
 	events |= status;
 	if (!events) {
@@ -651,7 +649,7 @@
 	}
 
 	if (status) {
-		pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, events);
+		pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, status);
 
 		/*
 		 * In MSI mode, all event bits must be zero before the port
@@ -725,8 +723,7 @@
 	}
 
 	/* Check Power Fault Detected */
-	if ((events & PCI_EXP_SLTSTA_PFD) && !ctrl->power_fault_detected) {
-		ctrl->power_fault_detected = 1;
+	if (events & PCI_EXP_SLTSTA_PFD) {
 		ctrl_err(ctrl, "Slot(%s): Power fault\n", slot_name(ctrl));
 		pciehp_set_indicators(ctrl, PCI_EXP_SLTCTL_PWR_IND_OFF,
 				      PCI_EXP_SLTCTL_ATTN_IND_ON);
@@ -746,7 +743,7 @@
 	 * Disable requests have higher priority than Presence Detect Changed
 	 * or Data Link Layer State Changed events.
 	 */
-	down_read(&ctrl->reset_lock);
+	down_read_nested(&ctrl->reset_lock, ctrl->depth);
 	if (events & DISABLE_SLOT)
 		pciehp_handle_disable_request(ctrl);
 	else if (events & (PCI_EXP_SLTSTA_PDC | PCI_EXP_SLTSTA_DLLSC))
@@ -843,7 +840,9 @@
 {
 	u16 mask;
 
-	mask = PCI_EXP_SLTCTL_HPIE | PCI_EXP_SLTCTL_DLLSCE;
+	mask = PCI_EXP_SLTCTL_DLLSCE;
+	if (!pciehp_poll_mode)
+		mask |= PCI_EXP_SLTCTL_HPIE;
 	pcie_write_cmd(ctrl, mask, mask);
 }
 
@@ -862,6 +861,32 @@
 	pcie_write_cmd(ctrl, 0, mask);
 }
 
+/**
+ * pciehp_slot_reset() - ignore link event caused by error-induced hot reset
+ * @dev: PCI Express port service device
+ *
+ * Called from pcie_portdrv_slot_reset() after AER or DPC initiated a reset
+ * further up in the hierarchy to recover from an error.  The reset was
+ * propagated down to this hotplug port.  Ignore the resulting link flap.
+ * If the link failed to retrain successfully, synthesize the ignored event.
+ * Surprise removal during reset is detected through Presence Detect Changed.
+ */
+int pciehp_slot_reset(struct pcie_device *dev)
+{
+	struct controller *ctrl = get_service_data(dev);
+
+	if (ctrl->state != ON_STATE)
+		return 0;
+
+	pcie_capability_write_word(dev->port, PCI_EXP_SLTSTA,
+				   PCI_EXP_SLTSTA_DLLSC);
+
+	if (!pciehp_check_link_active(ctrl))
+		pciehp_request(ctrl, PCI_EXP_SLTSTA_DLLSC);
+
+	return 0;
+}
+
 /*
  * pciehp has a 1:1 bus:slot relationship so we ultimately want a secondary
  * bus reset of the bridge, but at the same time we want to ensure that it is
@@ -880,7 +905,7 @@
 	if (probe)
 		return 0;
 
-	down_write(&ctrl->reset_lock);
+	down_write_nested(&ctrl->reset_lock, ctrl->depth);
 
 	if (!ATTN_BUTTN(ctrl)) {
 		ctrl_mask |= PCI_EXP_SLTCTL_PDCE;
@@ -936,6 +961,20 @@
 
 #define FLAG(x, y)	(((x) & (y)) ? '+' : '-')
 
+static inline int pcie_hotplug_depth(struct pci_dev *dev)
+{
+	struct pci_bus *bus = dev->bus;
+	int depth = 0;
+
+	while (bus->parent) {
+		bus = bus->parent;
+		if (bus->self && bus->self->is_hotplug_bridge)
+			depth++;
+	}
+
+	return depth;
+}
+
 struct controller *pcie_init(struct pcie_device *dev)
 {
 	struct controller *ctrl;
@@ -949,6 +988,7 @@
 		return NULL;
 
 	ctrl->pcie = dev;
+	ctrl->depth = pcie_hotplug_depth(dev->port);
 	pcie_capability_read_dword(pdev, PCI_EXP_SLTCAP, &slot_cap);
 
 	if (pdev->hotplug_user_indicators)
@@ -1042,6 +1082,8 @@
 }
 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
 			      PCI_CLASS_BRIDGE_PCI, 8, quirk_cmd_compl);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_QCOM, 0x0110,
+			      PCI_CLASS_BRIDGE_PCI, 8, quirk_cmd_compl);
 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_QCOM, 0x0400,
 			      PCI_CLASS_BRIDGE_PCI, 8, quirk_cmd_compl);
 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_QCOM, 0x0401,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/pciehp_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/pciehp_pci.c
@@ -63,7 +63,14 @@
 
 	pci_assign_unassigned_bridge_resources(bridge);
 	pcie_bus_configure_settings(parent);
+
+	/*
+	 * Release reset_lock during driver binding
+	 * to avoid AB-BA deadlock with device_lock.
+	 */
+	up_read(&ctrl->reset_lock);
 	pci_bus_add_devices(parent);
+	down_read_nested(&ctrl->reset_lock, ctrl->depth);
 
  out:
 	pci_unlock_rescan_remove();
@@ -104,7 +111,15 @@
 	list_for_each_entry_safe_reverse(dev, temp, &parent->devices,
 					 bus_list) {
 		pci_dev_get(dev);
+
+		/*
+		 * Release reset_lock during driver unbinding
+		 * to avoid AB-BA deadlock with device_lock.
+		 */
+		up_read(&ctrl->reset_lock);
 		pci_stop_and_remove_bus_device(dev);
+		down_read_nested(&ctrl->reset_lock, ctrl->depth);
+
 		/*
 		 * Ensure that no new Requests will be generated from
 		 * the device.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/pnv_php.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/pnv_php.c
@@ -38,7 +38,6 @@
 				bool disable_device)
 {
 	struct pci_dev *pdev = php_slot->pdev;
-	int irq = php_slot->irq;
 	u16 ctrl;
 
 	if (php_slot->irq > 0) {
@@ -57,7 +56,7 @@
 		php_slot->wq = NULL;
 	}
 
-	if (disable_device || irq > 0) {
+	if (disable_device) {
 		if (pdev->msix_enabled)
 			pci_disable_msix(pdev);
 		else if (pdev->msi_enabled)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/hotplug/s390_pci_hpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/hotplug/s390_pci_hpc.c
@@ -57,6 +57,29 @@
 	return zpci_deconfigure_device(zdev);
 }
 
+static int reset_slot(struct hotplug_slot *hotplug_slot, bool probe)
+{
+	struct zpci_dev *zdev = container_of(hotplug_slot, struct zpci_dev,
+					     hotplug_slot);
+
+	if (zdev->state != ZPCI_FN_STATE_CONFIGURED)
+		return -EIO;
+	/*
+	 * We can't take the zdev->lock as reset_slot may be called during
+	 * probing and/or device removal which already happens under the
+	 * zdev->lock. Instead the user should use the higher level
+	 * pci_reset_function() or pci_bus_reset() which hold the PCI device
+	 * lock preventing concurrent removal. If not using these functions
+	 * holding the PCI device lock is required.
+	 */
+
+	/* As long as the function is configured we can reset */
+	if (probe)
+		return 0;
+
+	return zpci_hot_reset_device(zdev);
+}
+
 static int get_power_status(struct hotplug_slot *hotplug_slot, u8 *value)
 {
 	struct zpci_dev *zdev = container_of(hotplug_slot, struct zpci_dev,
@@ -76,6 +99,7 @@
 static const struct hotplug_slot_ops s390_hotplug_slot_ops = {
 	.enable_slot =		enable_slot,
 	.disable_slot =		disable_slot,
+	.reset_slot =		reset_slot,
 	.get_power_status =	get_power_status,
 	.get_adapter_status =	get_adapter_status,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/iov.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/iov.c
@@ -14,7 +14,7 @@
 #include <linux/delay.h>
 #include "pci.h"
 
-#define VIRTFN_ID_LEN	16
+#define VIRTFN_ID_LEN	17	/* "virtfn%u\0" for 2^32 - 1 */
 
 int pci_iov_virtfn_bus(struct pci_dev *dev, int vf_id)
 {
@@ -706,6 +706,7 @@
 	struct pci_sriov *iov;
 	struct resource *res;
 	struct pci_dev *pdev;
+	u32 sriovbars[PCI_SRIOV_NUM_BARS];
 
 	pci_read_config_word(dev, pos + PCI_SRIOV_CTRL, &ctrl);
 	if (ctrl & PCI_SRIOV_CTRL_VFE) {
@@ -742,6 +743,10 @@
 	if (!iov)
 		return -ENOMEM;
 
+	/* Sizing SR-IOV BARs with VF Enable cleared - no decode */
+	__pci_size_stdbars(dev, PCI_SRIOV_NUM_BARS,
+			   pos + PCI_SRIOV_BAR, sriovbars);
+
 	nres = 0;
 	for (i = 0; i < PCI_SRIOV_NUM_BARS; i++) {
 		res = &dev->resource[i + PCI_IOV_RESOURCES];
@@ -753,7 +758,8 @@
 			bar64 = (res->flags & IORESOURCE_MEM_64) ? 1 : 0;
 		else
 			bar64 = __pci_read_base(dev, pci_bar_unknown, res,
-						pos + PCI_SRIOV_BAR + i * 4);
+						pos + PCI_SRIOV_BAR + i * 4,
+						&sriovbars[i]);
 		if (!res->flags)
 			continue;
 		if (resource_size(res) & (PAGE_SIZE - 1)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/irq.c
@@ -44,6 +44,8 @@
 	va_start(ap, fmt);
 	devname = kvasprintf(GFP_KERNEL, fmt, ap);
 	va_end(ap);
+	if (!devname)
+		return -ENOMEM;
 
 	ret = request_threaded_irq(pci_irq_vector(dev, nr), handler, thread_fn,
 				   irqflags, devname, dev_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/msi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/msi.c
@@ -148,6 +148,9 @@
 	raw_spinlock_t *lock = &desc->dev->msi_lock;
 	unsigned long flags;
 
+	if (!desc->msi_attrib.can_mask)
+		return;
+
 	raw_spin_lock_irqsave(lock, flags);
 	desc->msi_mask &= ~clear;
 	desc->msi_mask |= set;
@@ -181,7 +184,8 @@
 {
 	void __iomem *desc_addr = pci_msix_desc_addr(desc);
 
-	writel(ctrl, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
+	if (desc->msi_attrib.can_mask)
+		writel(ctrl, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
 }
 
 static inline void pci_msix_mask(struct msi_desc *desc)
@@ -200,23 +204,17 @@
 
 static void __pci_msi_mask_desc(struct msi_desc *desc, u32 mask)
 {
-	if (pci_msi_ignore_mask || desc->msi_attrib.is_virtual)
-		return;
-
 	if (desc->msi_attrib.is_msix)
 		pci_msix_mask(desc);
-	else if (desc->msi_attrib.maskbit)
+	else
 		pci_msi_mask(desc, mask);
 }
 
 static void __pci_msi_unmask_desc(struct msi_desc *desc, u32 mask)
 {
-	if (pci_msi_ignore_mask || desc->msi_attrib.is_virtual)
-		return;
-
 	if (desc->msi_attrib.is_msix)
 		pci_msix_unmask(desc);
-	else if (desc->msi_attrib.maskbit)
+	else
 		pci_msi_unmask(desc, mask);
 }
 
@@ -370,6 +368,11 @@
 			for (i = 0; i < entry->nvec_used; i++)
 				BUG_ON(irq_has_action(entry->irq + i));
 
+	if (dev->msi_irq_groups) {
+		msi_destroy_sysfs(&dev->dev, dev->msi_irq_groups);
+		dev->msi_irq_groups = NULL;
+	}
+
 	pci_msi_teardown_msi_irqs(dev);
 
 	list_for_each_entry_safe(entry, tmp, msi_list, list) {
@@ -381,11 +384,6 @@
 		list_del(&entry->list);
 		free_msi_entry(entry);
 	}
-
-	if (dev->msi_irq_groups) {
-		msi_destroy_sysfs(&dev->dev, dev->msi_irq_groups);
-		dev->msi_irq_groups = NULL;
-	}
 }
 
 static void pci_intx_for_msi(struct pci_dev *dev, int enable)
@@ -479,12 +477,16 @@
 		goto out;
 
 	pci_read_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, &control);
+	/* Lies, damned lies, and MSIs */
+	if (dev->dev_flags & PCI_DEV_FLAGS_HAS_MSI_MASKING)
+		control |= PCI_MSI_FLAGS_MASKBIT;
 
 	entry->msi_attrib.is_msix	= 0;
 	entry->msi_attrib.is_64		= !!(control & PCI_MSI_FLAGS_64BIT);
 	entry->msi_attrib.is_virtual    = 0;
 	entry->msi_attrib.entry_nr	= 0;
-	entry->msi_attrib.maskbit	= !!(control & PCI_MSI_FLAGS_MASKBIT);
+	entry->msi_attrib.can_mask	= !pci_msi_ignore_mask &&
+					  !!(control & PCI_MSI_FLAGS_MASKBIT);
 	entry->msi_attrib.default_irq	= dev->irq;	/* Save IOAPIC IRQ */
 	entry->msi_attrib.multi_cap	= (control & PCI_MSI_FLAGS_QMASK) >> 1;
 	entry->msi_attrib.multiple	= ilog2(__roundup_pow_of_two(nvec));
@@ -495,7 +497,7 @@
 		entry->mask_pos = dev->msi_cap + PCI_MSI_MASK_32;
 
 	/* Save the initial mask status */
-	if (entry->msi_attrib.maskbit)
+	if (entry->msi_attrib.can_mask)
 		pci_read_config_dword(dev, entry->mask_pos, &entry->msi_mask);
 
 out:
@@ -638,10 +640,13 @@
 		entry->msi_attrib.is_virtual =
 			entry->msi_attrib.entry_nr >= vec_count;
 
+		entry->msi_attrib.can_mask	= !pci_msi_ignore_mask &&
+						  !entry->msi_attrib.is_virtual;
+
 		entry->msi_attrib.default_irq	= dev->irq;
 		entry->mask_base		= base;
 
-		if (!entry->msi_attrib.is_virtual) {
+		if (entry->msi_attrib.can_mask) {
 			addr = pci_msix_desc_addr(entry);
 			entry->msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
 		}
@@ -771,7 +776,7 @@
 	free_msi_irqs(dev);
 
 out_disable:
-	pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_ENABLE, 0);
+	pci_msix_clear_and_set_ctrl(dev, PCI_MSIX_FLAGS_MASKALL | PCI_MSIX_FLAGS_ENABLE, 0);
 
 	return ret;
 }
@@ -1181,19 +1186,24 @@
 
 /**
  * pci_irq_vector - return Linux IRQ number of a device vector
- * @dev: PCI device to operate on
- * @nr: device-relative interrupt vector index (0-based).
+ * @dev:	PCI device to operate on
+ * @nr:		Interrupt vector index (0-based)
+ *
+ * @nr has the following meanings depending on the interrupt mode:
+ *   MSI-X:	The index in the MSI-X vector table
+ *   MSI:	The index of the enabled MSI vectors
+ *   INTx:	Must be 0
+ *
+ * Return: The Linux interrupt number or -EINVAl if @nr is out of range.
  */
 int pci_irq_vector(struct pci_dev *dev, unsigned int nr)
 {
 	if (dev->msix_enabled) {
 		struct msi_desc *entry;
-		int i = 0;
 
 		for_each_pci_msi_entry(entry, dev) {
-			if (i == nr)
+			if (entry->msi_attrib.entry_nr == nr)
 				return entry->irq;
-			i++;
 		}
 		WARN_ON_ONCE(1);
 		return -EINVAL;
@@ -1217,17 +1227,22 @@
  * pci_irq_get_affinity - return the affinity of a particular MSI vector
  * @dev:	PCI device to operate on
  * @nr:		device-relative interrupt vector index (0-based).
+ *
+ * @nr has the following meanings depending on the interrupt mode:
+ *   MSI-X:	The index in the MSI-X vector table
+ *   MSI:	The index of the enabled MSI vectors
+ *   INTx:	Must be 0
+ *
+ * Return: A cpumask pointer or NULL if @nr is out of range
  */
 const struct cpumask *pci_irq_get_affinity(struct pci_dev *dev, int nr)
 {
 	if (dev->msix_enabled) {
 		struct msi_desc *entry;
-		int i = 0;
 
 		for_each_pci_msi_entry(entry, dev) {
-			if (i == nr)
+			if (entry->msi_attrib.entry_nr == nr)
 				return &entry->affinity->mask;
-			i++;
 		}
 		WARN_ON_ONCE(1);
 		return NULL;
@@ -1289,7 +1304,7 @@
 
 	return (irq_hw_number_t)desc->msi_attrib.entry_nr |
 		pci_dev_id(dev) << 11 |
-		(pci_domain_nr(dev->bus) & 0xFFFFFFFF) << 27;
+		((irq_hw_number_t)(pci_domain_nr(dev->bus) & 0xFFFFFFFF)) << 27;
 }
 
 static inline bool pci_msi_desc_is_multi_msi(struct msi_desc *desc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/p2pdma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/p2pdma.c
@@ -219,7 +219,7 @@
 	error = gen_pool_add_owner(p2pdma->pool, (unsigned long)addr,
 			pci_bus_address(pdev, bar) + offset,
 			range_len(&pgmap->range), dev_to_node(&pdev->dev),
-			pgmap->ref);
+			&pgmap->ref);
 	if (error)
 		goto pages_free;
 
@@ -536,7 +536,7 @@
 	p2pdma = rcu_dereference(provider->p2pdma);
 	if (p2pdma)
 		xa_store(&p2pdma->map_types, map_types_idx(client),
-			 xa_mk_value(map_type), GFP_KERNEL);
+			 xa_mk_value(map_type), GFP_ATOMIC);
 	rcu_read_unlock();
 	return map_type;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pci-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pci-acpi.c
@@ -910,7 +910,7 @@
 {
 	int acpi_state, d_max;
 
-	if (pdev->no_d3cold)
+	if (pdev->no_d3cold || !pdev->d3cold_allowed)
 		d_max = ACPI_STATE_D3_HOT;
 	else
 		d_max = ACPI_STATE_D3_COLD;
@@ -976,9 +976,11 @@
 
 static bool acpi_pci_bridge_d3(struct pci_dev *dev)
 {
-	const union acpi_object *obj;
-	struct acpi_device *adev;
 	struct pci_dev *rpdev;
+	struct acpi_device *adev;
+	acpi_status status;
+	unsigned long long state;
+	const union acpi_object *obj;
 
 	if (!dev->is_hotplug_bridge)
 		return false;
@@ -987,12 +989,6 @@
 	if (acpi_pci_power_manageable(dev))
 		return true;
 
-	/*
-	 * The ACPI firmware will provide the device-specific properties through
-	 * _DSD configuration object. Look for the 'HotPlugSupportInD3' property
-	 * for the root port and if it is set we know the hierarchy behind it
-	 * supports D3 just fine.
-	 */
 	rpdev = pcie_find_root_port(dev);
 	if (!rpdev)
 		return false;
@@ -1001,11 +997,34 @@
 	if (!adev)
 		return false;
 
-	if (acpi_dev_get_property(adev, "HotPlugSupportInD3",
-				   ACPI_TYPE_INTEGER, &obj) < 0)
+	/*
+	 * If the Root Port cannot signal wakeup signals at all, i.e., it
+	 * doesn't supply a wakeup GPE via _PRW, it cannot signal hotplug
+	 * events from low-power states including D3hot and D3cold.
+	 */
+	if (!adev->wakeup.flags.valid)
+		return false;
+
+	/*
+	 * If the Root Port cannot wake itself from D3hot or D3cold, we
+	 * can't use D3.
+	 */
+	status = acpi_evaluate_integer(adev->handle, "_S0W", NULL, &state);
+	if (ACPI_SUCCESS(status) && state < ACPI_STATE_D3_HOT)
 		return false;
 
-	return obj->integer.value == 1;
+	/*
+	 * The "HotPlugSupportInD3" property in a Root Port _DSD indicates
+	 * the Port can signal hotplug events while in D3.  We assume any
+	 * bridges *below* that Root Port can also signal hotplug events
+	 * while in D3.
+	 */
+	if (!acpi_dev_get_property(adev, "HotPlugSupportInD3",
+				   ACPI_TYPE_INTEGER, &obj) &&
+	    obj->integer.value == 1)
+		return true;
+
+	return false;
 }
 
 static int acpi_pci_set_power_state(struct pci_dev *dev, pci_power_t state)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pci-bridge-emul.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pci-bridge-emul.c
@@ -139,8 +139,13 @@
 		.ro = GENMASK(7, 0),
 	},
 
+	/*
+	 * If expansion ROM is unsupported then ROM Base Address register must
+	 * be implemented as read-only register that return 0 when read, same
+	 * as for unused Base Address registers.
+	 */
 	[PCI_ROM_ADDRESS1 / 4] = {
-		.rw = GENMASK(31, 11) | BIT(0),
+		.ro = ~0,
 	},
 
 	/*
@@ -171,41 +176,55 @@
 	[PCI_CAP_LIST_ID / 4] = {
 		/*
 		 * Capability ID, Next Capability Pointer and
-		 * Capabilities register are all read-only.
+		 * bits [14:0] of Capabilities register are all read-only.
+		 * Bit 15 of Capabilities register is reserved.
 		 */
-		.ro = ~0,
+		.ro = GENMASK(30, 0),
 	},
 
 	[PCI_EXP_DEVCAP / 4] = {
-		.ro = ~0,
+		/*
+		 * Bits [31:29] and [17:16] are reserved.
+		 * Bits [27:18] are reserved for non-upstream ports.
+		 * Bits 28 and [14:6] are reserved for non-endpoint devices.
+		 * Other bits are read-only.
+		 */
+		.ro = BIT(15) | GENMASK(5, 0),
 	},
 
 	[PCI_EXP_DEVCTL / 4] = {
-		/* Device control register is RW */
-		.rw = GENMASK(15, 0),
+		/*
+		 * Device control register is RW, except bit 15 which is
+		 * reserved for non-endpoints or non-PCIe-to-PCI/X bridges.
+		 */
+		.rw = GENMASK(14, 0),
 
 		/*
 		 * Device status register has bits 6 and [3:0] W1C, [5:4] RO,
-		 * the rest is reserved
+		 * the rest is reserved. Also bit 6 is reserved for non-upstream
+		 * ports.
 		 */
-		.w1c = (BIT(6) | GENMASK(3, 0)) << 16,
+		.w1c = GENMASK(3, 0) << 16,
 		.ro = GENMASK(5, 4) << 16,
 	},
 
 	[PCI_EXP_LNKCAP / 4] = {
-		/* All bits are RO, except bit 23 which is reserved */
-		.ro = lower_32_bits(~BIT(23)),
+		/*
+		 * All bits are RO, except bit 23 which is reserved and
+		 * bit 18 which is reserved for non-upstream ports.
+		 */
+		.ro = lower_32_bits(~(BIT(23) | PCI_EXP_LNKCAP_CLKPM)),
 	},
 
 	[PCI_EXP_LNKCTL / 4] = {
 		/*
 		 * Link control has bits [15:14], [11:3] and [1:0] RW, the
-		 * rest is reserved.
+		 * rest is reserved. Bit 8 is reserved for non-upstream ports.
 		 *
 		 * Link status has bits [13:0] RO, and bits [15:14]
 		 * W1C.
 		 */
-		.rw = GENMASK(15, 14) | GENMASK(11, 3) | GENMASK(1, 0),
+		.rw = GENMASK(15, 14) | GENMASK(11, 9) | GENMASK(7, 3) | GENMASK(1, 0),
 		.ro = GENMASK(13, 0) << 16,
 		.w1c = GENMASK(15, 14) << 16,
 	},
@@ -251,6 +270,49 @@
 		.ro = GENMASK(15, 0) | PCI_EXP_RTSTA_PENDING,
 		.w1c = PCI_EXP_RTSTA_PME,
 	},
+
+	[PCI_EXP_DEVCAP2 / 4] = {
+		/*
+		 * Device capabilities 2 register has reserved bits [30:27].
+		 * Also bits [26:24] are reserved for non-upstream ports.
+		 */
+		.ro = BIT(31) | GENMASK(23, 0),
+	},
+
+	[PCI_EXP_DEVCTL2 / 4] = {
+		/*
+		 * Device control 2 register is RW. Bit 11 is reserved for
+		 * non-upstream ports.
+		 *
+		 * Device status 2 register is reserved.
+		 */
+		.rw = GENMASK(15, 12) | GENMASK(10, 0),
+	},
+
+	[PCI_EXP_LNKCAP2 / 4] = {
+		/* Link capabilities 2 register has reserved bits [30:25] and 0. */
+		.ro = BIT(31) | GENMASK(24, 1),
+	},
+
+	[PCI_EXP_LNKCTL2 / 4] = {
+		/*
+		 * Link control 2 register is RW.
+		 *
+		 * Link status 2 register has bits 5, 15 W1C;
+		 * bits 10, 11 reserved and others are RO.
+		 */
+		.rw = GENMASK(15, 0),
+		.w1c = (BIT(15) | BIT(5)) << 16,
+		.ro = (GENMASK(14, 12) | GENMASK(9, 6) | GENMASK(4, 0)) << 16,
+	},
+
+	[PCI_EXP_SLTCAP2 / 4] = {
+		/* Slot capabilities 2 register is reserved. */
+	},
+
+	[PCI_EXP_SLTCTL2 / 4] = {
+		/* Both Slot control 2 and Slot status 2 registers are reserved. */
+	},
 };
 
 /*
@@ -265,7 +327,11 @@
 {
 	BUILD_BUG_ON(sizeof(bridge->conf) != PCI_BRIDGE_CONF_END);
 
-	bridge->conf.class_revision |= cpu_to_le32(PCI_CLASS_BRIDGE_PCI << 16);
+	/*
+	 * class_revision: Class is high 24 bits and revision is low 8 bit of this member,
+	 * while class for PCI Bridge Normal Decode has the 24-bit value: PCI_CLASS_BRIDGE_PCI << 8
+	 */
+	bridge->conf.class_revision |= cpu_to_le32((PCI_CLASS_BRIDGE_PCI << 8) << 8);
 	bridge->conf.header_type = PCI_HEADER_TYPE_BRIDGE;
 	bridge->conf.cache_line_size = 0x10;
 	bridge->conf.status = cpu_to_le16(PCI_STATUS_CAP_LIST);
@@ -277,11 +343,9 @@
 
 	if (bridge->has_pcie) {
 		bridge->conf.capabilities_pointer = PCI_CAP_PCIE_START;
+		bridge->conf.status |= cpu_to_le16(PCI_STATUS_CAP_LIST);
 		bridge->pcie_conf.cap_id = PCI_CAP_ID_EXP;
-		/* Set PCIe v2, root port, slot support */
-		bridge->pcie_conf.cap =
-			cpu_to_le16(PCI_EXP_TYPE_ROOT_PORT << 4 | 2 |
-				    PCI_EXP_FLAGS_SLOT);
+		bridge->pcie_conf.cap |= cpu_to_le16(PCI_EXP_TYPE_ROOT_PORT << 4);
 		bridge->pcie_cap_regs_behavior =
 			kmemdup(pcie_cap_regs_behavior,
 				sizeof(pcie_cap_regs_behavior),
@@ -290,6 +354,27 @@
 			kfree(bridge->pci_regs_behavior);
 			return -ENOMEM;
 		}
+		/* These bits are applicable only for PCI and reserved on PCIe */
+		bridge->pci_regs_behavior[PCI_CACHE_LINE_SIZE / 4].ro &=
+			~GENMASK(15, 8);
+		bridge->pci_regs_behavior[PCI_COMMAND / 4].ro &=
+			~((PCI_COMMAND_SPECIAL | PCI_COMMAND_INVALIDATE |
+			   PCI_COMMAND_VGA_PALETTE | PCI_COMMAND_WAIT |
+			   PCI_COMMAND_FAST_BACK) |
+			  (PCI_STATUS_66MHZ | PCI_STATUS_FAST_BACK |
+			   PCI_STATUS_DEVSEL_MASK) << 16);
+		bridge->pci_regs_behavior[PCI_PRIMARY_BUS / 4].ro &=
+			~GENMASK(31, 24);
+		bridge->pci_regs_behavior[PCI_IO_BASE / 4].ro &=
+			~((PCI_STATUS_66MHZ | PCI_STATUS_FAST_BACK |
+			   PCI_STATUS_DEVSEL_MASK) << 16);
+		bridge->pci_regs_behavior[PCI_INTERRUPT_LINE / 4].rw &=
+			~((PCI_BRIDGE_CTL_MASTER_ABORT |
+			   BIT(8) | BIT(9) | BIT(11)) << 16);
+		bridge->pci_regs_behavior[PCI_INTERRUPT_LINE / 4].ro &=
+			~((PCI_BRIDGE_CTL_FAST_BACK) << 16);
+		bridge->pci_regs_behavior[PCI_INTERRUPT_LINE / 4].w1c &=
+			~(BIT(10) << 16);
 	}
 
 	if (flags & PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR) {
@@ -431,8 +516,21 @@
 	/* Clear the W1C bits */
 	new &= ~((value << shift) & (behavior[reg / 4].w1c & mask));
 
+	/* Save the new value with the cleared W1C bits into the cfgspace */
 	cfgspace[reg / 4] = cpu_to_le32(new);
 
+	/*
+	 * Clear the W1C bits not specified by the write mask, so that the
+	 * write_op() does not clear them.
+	 */
+	new &= ~(behavior[reg / 4].w1c & ~mask);
+
+	/*
+	 * Set the W1C bits specified by the write mask, so that write_op()
+	 * knows about that they are to be cleared.
+	 */
+	new |= (value << shift) & (behavior[reg / 4].w1c & mask);
+
 	if (write_op)
 		write_op(bridge, reg, old, new, mask);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pci-driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pci-driver.c
@@ -459,16 +459,21 @@
 	struct pci_dev *pci_dev = to_pci_dev(dev);
 	struct pci_driver *drv = pci_dev->driver;
 
-	if (drv) {
-		if (drv->remove) {
-			pm_runtime_get_sync(dev);
-			drv->remove(pci_dev);
-			pm_runtime_put_noidle(dev);
-		}
-		pcibios_free_irq(pci_dev);
-		pci_dev->driver = NULL;
-		pci_iov_remove(pci_dev);
-	}
+	if (drv->remove) {
+		pm_runtime_get_sync(dev);
+		/*
+		 * If the driver provides a .runtime_idle() callback and it has
+		 * started to run already, it may continue to run in parallel
+		 * with the code below, so wait until all of the runtime PM
+		 * activity has completed.
+		 */
+		pm_runtime_barrier(dev);
+		drv->remove(pci_dev);
+		pm_runtime_put_noidle(dev);
+	}
+	pcibios_free_irq(pci_dev);
+	pci_dev->driver = NULL;
+	pci_iov_remove(pci_dev);
 
 	/* Undo the runtime PM settings in local_pci_probe() */
 	pm_runtime_put_sync(dev);
@@ -743,6 +748,12 @@
 
 	pci_dev->skip_bus_pm = false;
 
+	/*
+	 * Disabling PTM allows some systems, e.g., Intel mobile chips
+	 * since Coffee Lake, to enter a lower-power PM state.
+	 */
+	pci_suspend_ptm(pci_dev);
+
 	if (pci_has_legacy_pm_support(pci_dev))
 		return pci_legacy_suspend(dev, PMSG_SUSPEND);
 
@@ -836,20 +847,15 @@
 		}
 	}
 
-	if (pci_dev->skip_bus_pm) {
+	if (!pci_dev->state_saved) {
+		pci_save_state(pci_dev);
+
 		/*
-		 * Either the device is a bridge with a child in D0 below it, or
-		 * the function is running for the second time in a row without
-		 * going through full resume, which is possible only during
-		 * suspend-to-idle in a spurious wakeup case.  The device should
-		 * be in D0 at this point, but if it is a bridge, it may be
-		 * necessary to save its state.
+		 * If the device is a bridge with a child in D0 below it,
+		 * it needs to stay in D0, so check skip_bus_pm to avoid
+		 * putting it into a low-power state in that case.
 		 */
-		if (!pci_dev->state_saved)
-			pci_save_state(pci_dev);
-	} else if (!pci_dev->state_saved) {
-		pci_save_state(pci_dev);
-		if (pci_power_manageable(pci_dev))
+		if (!pci_dev->skip_bus_pm && pci_power_manageable(pci_dev))
 			pci_prepare_to_sleep(pci_dev);
 	}
 
@@ -925,7 +931,7 @@
 	pcie_pme_root_status_cleanup(pci_dev);
 
 	if (!skip_bus_pm && prev_state == PCI_D3cold)
-		pci_bridge_wait_for_secondary_bus(pci_dev);
+		pci_bridge_wait_for_secondary_bus(pci_dev, "resume", PCI_RESET_WAIT);
 
 	if (pci_has_legacy_pm_support(pci_dev))
 		return 0;
@@ -956,6 +962,8 @@
 	if (pci_dev->state_saved)
 		pci_restore_standard_config(pci_dev);
 
+	pci_resume_ptm(pci_dev);
+
 	if (pci_has_legacy_pm_support(pci_dev))
 		return pci_legacy_resume(dev);
 
@@ -1243,6 +1251,8 @@
 	pci_power_t prev = pci_dev->current_state;
 	int error;
 
+	pci_suspend_ptm(pci_dev);
+
 	/*
 	 * If pci_dev->driver is not set (unbound), we leave the device in D0,
 	 * but it may go to D3cold when the bridge above it runtime suspends.
@@ -1304,6 +1314,7 @@
 	 * D3cold when the bridge above it runtime suspended.
 	 */
 	pci_restore_standard_config(pci_dev);
+	pci_resume_ptm(pci_dev);
 
 	if (!pci_dev->driver)
 		return 0;
@@ -1312,7 +1323,7 @@
 	pci_pm_default_resume(pci_dev);
 
 	if (prev_state == PCI_D3cold)
-		pci_bridge_wait_for_secondary_bus(pci_dev);
+		pci_bridge_wait_for_secondary_bus(pci_dev, "resume", PCI_RESET_WAIT);
 
 	if (pm && pm->runtime_resume)
 		error = pm->runtime_resume(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pci-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pci-sysfs.c
@@ -12,7 +12,7 @@
  * Modeled after usb's driverfs.c
  */
 
-
+#include <linux/bitfield.h>
 #include <linux/kernel.h>
 #include <linux/sched.h>
 #include <linux/pci.h>
@@ -208,8 +208,7 @@
 	if (err)
 		return -EINVAL;
 
-	return sysfs_emit(buf, "%u\n",
-		(linkstat & PCI_EXP_LNKSTA_NLW) >> PCI_EXP_LNKSTA_NLW_SHIFT);
+	return sysfs_emit(buf, "%u\n", FIELD_GET(PCI_EXP_LNKSTA_NLW, linkstat));
 }
 static DEVICE_ATTR_RO(current_link_width);
 
@@ -497,6 +496,31 @@
 static struct device_attribute dev_attr_bus_rescan = __ATTR(rescan, 0200, NULL,
 							    bus_rescan_store);
 
+static ssize_t reset_subordinate_store(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct pci_bus *bus = pdev->subordinate;
+	unsigned long val;
+
+	if (!capable(CAP_SYS_ADMIN))
+		return -EPERM;
+
+	if (kstrtoul(buf, 0, &val) < 0)
+		return -EINVAL;
+
+	if (val) {
+		int ret = __pci_reset_bus(bus);
+
+		if (ret)
+			return ret;
+	}
+
+	return count;
+}
+static DEVICE_ATTR_WO(reset_subordinate);
+
 #if defined(CONFIG_PM) && defined(CONFIG_ACPI)
 static ssize_t d3cold_allowed_store(struct device *dev,
 				    struct device_attribute *attr,
@@ -509,10 +533,7 @@
 		return -EINVAL;
 
 	pdev->d3cold_allowed = !!val;
-	if (pdev->d3cold_allowed)
-		pci_d3cold_enable(pdev);
-	else
-		pci_d3cold_disable(pdev);
+	pci_bridge_d3_update(pdev);
 
 	pm_runtime_resume(dev);
 
@@ -624,6 +645,7 @@
 static struct attribute *pci_bridge_attrs[] = {
 	&dev_attr_subordinate_bus_number.attr,
 	&dev_attr_secondary_bus_number.attr,
+	&dev_attr_reset_subordinate.attr,
 	NULL,
 };
 
@@ -1179,11 +1201,9 @@
 
 	sysfs_bin_attr_init(res_attr);
 	if (write_combine) {
-		pdev->res_attr_wc[num] = res_attr;
 		sprintf(res_attr_name, "resource%d_wc", num);
 		res_attr->mmap = pci_mmap_resource_wc;
 	} else {
-		pdev->res_attr[num] = res_attr;
 		sprintf(res_attr_name, "resource%d", num);
 		if (pci_resource_flags(pdev, num) & IORESOURCE_IO) {
 			res_attr->read = pci_read_resource_io;
@@ -1201,10 +1221,17 @@
 	res_attr->size = pci_resource_len(pdev, num);
 	res_attr->private = (void *)(unsigned long)num;
 	retval = sysfs_create_bin_file(&pdev->dev.kobj, res_attr);
-	if (retval)
+	if (retval) {
 		kfree(res_attr);
+		return retval;
+	}
 
-	return retval;
+	if (write_combine)
+		pdev->res_attr_wc[num] = res_attr;
+	else
+		pdev->res_attr[num] = res_attr;
+
+	return 0;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pci.c
@@ -163,8 +163,22 @@
 }
 __setup("pcie_port_pm=", pcie_port_pm_setup);
 
-/* Time to wait after a reset for device to become responsive */
-#define PCIE_RESET_READY_POLL_MS 60000
+static const struct dmi_system_id aspm_fix_whitelist[] = {
+	{
+		.ident = "LENOVO Stealth Thinkstation",
+		.matches = {
+			DMI_MATCH(DMI_BIOS_VERSION, "S07K"),
+		},
+	},
+	{
+		.ident = "Dell Inc. Precision 7960 Tower",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Precision 7960 Tower"),
+		},
+	},
+	{}
+};
 
 /**
  * pci_bus_max_busnr - returns maximum PCI bus number of given bus' children
@@ -823,6 +837,9 @@
 			return 1;
 	}
 
+	if (dev->bus->self)
+		pcie_aspm_pm_state_change(dev->bus->self);
+
 	return 0;
 }
 
@@ -1255,7 +1272,7 @@
 			return -ENOTTY;
 		}
 
-		if (delay > 1000)
+		if (delay > PCI_RESET_WAIT)
 			pci_info(dev, "not ready %dms after %s; waiting\n",
 				 delay - 1, reset_type);
 
@@ -1264,7 +1281,7 @@
 		pci_read_config_dword(dev, PCI_COMMAND, &id);
 	}
 
-	if (delay > 1000)
+	if (delay > PCI_RESET_WAIT)
 		pci_info(dev, "ready %dms after %s\n", delay - 1,
 			 reset_type);
 
@@ -1477,6 +1494,24 @@
 	return 0;
 }
 
+void pci_bridge_reconfigure_ltr(struct pci_dev *dev)
+{
+#ifdef CONFIG_PCIEASPM
+	struct pci_dev *bridge;
+	u32 ctl;
+
+	bridge = pci_upstream_bridge(dev);
+	if (bridge && bridge->ltr_path) {
+		pcie_capability_read_dword(bridge, PCI_EXP_DEVCTL2, &ctl);
+		if (!(ctl & PCI_EXP_DEVCTL2_LTR_EN)) {
+			pci_dbg(bridge, "re-enabling LTR\n");
+			pcie_capability_set_word(bridge, PCI_EXP_DEVCTL2,
+						 PCI_EXP_DEVCTL2_LTR_EN);
+		}
+	}
+#endif
+}
+
 static void pci_restore_pcie_state(struct pci_dev *dev)
 {
 	int i = 0;
@@ -1487,6 +1522,13 @@
 	if (!save_state)
 		return;
 
+	/*
+	 * Downstream ports reset the LTR enable bit when link goes down.
+	 * Check and re-configure the bit here before restoring device.
+	 * PCIe r5.0, sec 7.5.3.16.
+	 */
+	pci_bridge_reconfigure_ltr(dev);
+
 	cap = (u16 *)&save_state->cap.data[0];
 	pcie_capability_write_word(dev, PCI_EXP_DEVCTL, cap[i++]);
 	pcie_capability_write_word(dev, PCI_EXP_LNKCTL, cap[i++]);
@@ -1598,6 +1640,8 @@
 		return i;
 
 	pci_save_ltr_state(dev);
+	if (dmi_check_system(aspm_fix_whitelist))
+		pci_save_aspm_l1ss_state(dev);
 	pci_save_dpc_state(dev);
 	pci_save_aer_state(dev);
 	pci_save_ptm_state(dev);
@@ -1704,6 +1748,8 @@
 	 * LTR itself (in the PCIe capability).
 	 */
 	pci_restore_ltr_state(dev);
+	if (dmi_check_system(aspm_fix_whitelist))
+		pci_restore_aspm_l1ss_state(dev);
 
 	pci_restore_pcie_state(dev);
 	pci_restore_pasid_state(dev);
@@ -2649,24 +2695,12 @@
 	if (target_state == PCI_POWER_ERROR)
 		return -EIO;
 
-	/*
-	 * There are systems (for example, Intel mobile chips since Coffee
-	 * Lake) where the power drawn while suspended can be significantly
-	 * reduced by disabling PTM on PCIe root ports as this allows the
-	 * port to enter a lower-power PM state and the SoC to reach a
-	 * lower-power idle state as a whole.
-	 */
-	if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT)
-		pci_disable_ptm(dev);
-
 	pci_enable_wake(dev, target_state, wakeup);
 
 	error = pci_set_power_state(dev, target_state);
 
-	if (error) {
+	if (error)
 		pci_enable_wake(dev, target_state, false);
-		pci_restore_ptm_state(dev);
-	}
 
 	return error;
 }
@@ -2704,23 +2738,12 @@
 
 	dev->runtime_d3cold = target_state == PCI_D3cold;
 
-	/*
-	 * There are systems (for example, Intel mobile chips since Coffee
-	 * Lake) where the power drawn while suspended can be significantly
-	 * reduced by disabling PTM on PCIe root ports as this allows the
-	 * port to enter a lower-power PM state and the SoC to reach a
-	 * lower-power idle state as a whole.
-	 */
-	if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT)
-		pci_disable_ptm(dev);
-
 	__pci_enable_wake(dev, target_state, pci_dev_run_wake(dev));
 
 	error = pci_set_power_state(dev, target_state);
 
 	if (error) {
 		pci_enable_wake(dev, target_state, false);
-		pci_restore_ptm_state(dev);
 		dev->runtime_d3cold = false;
 	}
 
@@ -2889,6 +2912,30 @@
 			DMI_MATCH(DMI_BOARD_NAME, "X299 DESIGNARE EX-CF"),
 		},
 	},
+	{
+		/*
+		 * Downstream device is not accessible after putting a root port
+		 * into D3cold and back into D0 on Elo Continental Z2 board
+		 */
+		.ident = "Elo Continental Z2",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Elo Touch Solutions"),
+			DMI_MATCH(DMI_BOARD_NAME, "Geminilake"),
+			DMI_MATCH(DMI_BOARD_VERSION, "Continental Z2"),
+		},
+	},
+	{
+		/*
+		 * Changing power state of root port dGPU is connected fails
+		 * https://gitlab.freedesktop.org/drm/amd/-/issues/3229
+		 */
+		.ident = "Hewlett-Packard HP Pavilion 17 Notebook PC/1972",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_BOARD_NAME, "1972"),
+			DMI_MATCH(DMI_BOARD_VERSION, "95.33"),
+		},
+	},
 #endif
 	{ }
 };
@@ -3398,6 +3445,13 @@
 	if (error)
 		pci_err(dev, "unable to allocate suspend buffer for LTR\n");
 
+	if (dmi_check_system(aspm_fix_whitelist)) {
+		error = pci_add_ext_cap_save_buffer(dev, PCI_EXT_CAP_ID_L1SS,
+						    2 * sizeof(u32));
+		if (error)
+			pci_err(dev, "unable to allocate suspend buffer for ASPM-L1SS\n");
+	}
+
 	pci_allocate_vc_save_buffers(dev);
 }
 
@@ -3643,14 +3697,14 @@
 		return 0;
 
 	pci_read_config_dword(pdev, pos + PCI_REBAR_CAP, &cap);
-	cap &= PCI_REBAR_CAP_SIZES;
+	cap = FIELD_GET(PCI_REBAR_CAP_SIZES, cap);
 
 	/* Sapphire RX 5600 XT Pulse has an invalid cap dword for BAR 0 */
 	if (pdev->vendor == PCI_VENDOR_ID_ATI && pdev->device == 0x731f &&
-	    bar == 0 && cap == 0x7000)
-		cap = 0x3f000;
+	    bar == 0 && cap == 0x700)
+		return 0x3f00;
 
-	return cap >> 4;
+	return cap;
 }
 EXPORT_SYMBOL(pci_rebar_get_possible_sizes);
 
@@ -3719,6 +3773,14 @@
 	struct pci_dev *bridge;
 	u32 cap, ctl2;
 
+	/*
+	 * Per PCIe r5.0, sec 9.3.5.10, the AtomicOp Requester Enable bit
+	 * in Device Control 2 is reserved in VFs and the PF value applies
+	 * to all associated VFs.
+	 */
+	if (dev->is_virtfn)
+		return -EINVAL;
+
 	if (!pci_is_pcie(dev))
 		return -EINVAL;
 
@@ -4866,24 +4928,31 @@
 /**
  * pci_bridge_wait_for_secondary_bus - Wait for secondary bus to be accessible
  * @dev: PCI bridge
+ * @reset_type: reset type in human-readable form
+ * @timeout: maximum time to wait for devices on secondary bus (milliseconds)
  *
  * Handle necessary delays before access to the devices on the secondary
- * side of the bridge are permitted after D3cold to D0 transition.
+ * side of the bridge are permitted after D3cold to D0 transition
+ * or Conventional Reset.
  *
  * For PCIe this means the delays in PCIe 5.0 section 6.6.1. For
  * conventional PCI it means Tpvrh + Trhfa specified in PCI 3.0 section
  * 4.3.2.
+ *
+ * Return 0 on success or -ENOTTY if the first device on the secondary bus
+ * failed to become accessible.
  */
-void pci_bridge_wait_for_secondary_bus(struct pci_dev *dev)
+int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type,
+				      int timeout)
 {
 	struct pci_dev *child;
-	int delay;
+	int delay, ret = 0;
 
 	if (pci_dev_is_disconnected(dev))
-		return;
+		return 0;
 
-	if (!pci_is_bridge(dev) || !dev->bridge_d3)
-		return;
+	if (!pci_is_bridge(dev))
+		return 0;
 
 	down_read(&pci_bus_sem);
 
@@ -4895,30 +4964,28 @@
 	 */
 	if (!dev->subordinate || list_empty(&dev->subordinate->devices)) {
 		up_read(&pci_bus_sem);
-		return;
+		return 0;
 	}
 
 	/* Take d3cold_delay requirements into account */
 	delay = pci_bus_max_d3cold_delay(dev->subordinate);
 	if (!delay) {
 		up_read(&pci_bus_sem);
-		return;
+		return 0;
 	}
 
-	child = list_first_entry(&dev->subordinate->devices, struct pci_dev,
-				 bus_list);
+	child = pci_dev_get(list_first_entry(&dev->subordinate->devices,
+					     struct pci_dev, bus_list));
 	up_read(&pci_bus_sem);
 
 	/*
 	 * Conventional PCI and PCI-X we need to wait Tpvrh + Trhfa before
-	 * accessing the device after reset (that is 1000 ms + 100 ms). In
-	 * practice this should not be needed because we don't do power
-	 * management for them (see pci_bridge_d3_possible()).
+	 * accessing the device after reset (that is 1000 ms + 100 ms).
 	 */
 	if (!pci_is_pcie(dev)) {
 		pci_dbg(dev, "waiting %d ms for secondary bus\n", 1000 + delay);
 		msleep(1000 + delay);
-		return;
+		goto put_child;
 	}
 
 	/*
@@ -4935,11 +5002,11 @@
 	 * configuration requests if we only wait for 100 ms (see
 	 * https://bugzilla.kernel.org/show_bug.cgi?id=203885).
 	 *
-	 * Therefore we wait for 100 ms and check for the device presence.
-	 * If it is still not present give it an additional 100 ms.
+	 * Therefore we wait for 100 ms and check for the device presence
+	 * until the timeout expires.
 	 */
 	if (!pcie_downstream_port(dev))
-		return;
+		goto put_child;
 
 	if (pcie_get_speed_cap(dev) <= PCIE_SPEED_5_0GT) {
 		pci_dbg(dev, "waiting %d ms for downstream link\n", delay);
@@ -4950,14 +5017,16 @@
 		if (!pcie_wait_for_link_delay(dev, true, delay)) {
 			/* Did not train, no need to wait any further */
 			pci_info(dev, "Data Link Layer Link Active not set in 1000 msec\n");
-			return;
+			ret = -ENOTTY;
+			goto put_child;
 		}
 	}
 
-	if (!pci_device_is_present(child)) {
-		pci_dbg(child, "waiting additional %d ms to become accessible\n", delay);
-		msleep(delay);
-	}
+	ret = pci_dev_wait(child, reset_type, timeout - delay);
+
+put_child:
+	pci_dev_put(child);
+	return ret;
 }
 
 void pci_reset_secondary_bus(struct pci_dev *dev)
@@ -4976,15 +5045,6 @@
 
 	ctrl &= ~PCI_BRIDGE_CTL_BUS_RESET;
 	pci_write_config_word(dev, PCI_BRIDGE_CONTROL, ctrl);
-
-	/*
-	 * Trhfa for conventional PCI is 2^25 clock cycles.
-	 * Assuming a minimum 33MHz clock this results in a 1s
-	 * delay before we can consider subordinate devices to
-	 * be re-initialized.  PCIe has some ways to shorten this,
-	 * but we don't make use of them yet.
-	 */
-	ssleep(1);
 }
 
 void __weak pcibios_reset_secondary_bus(struct pci_dev *dev)
@@ -5003,7 +5063,8 @@
 {
 	pcibios_reset_secondary_bus(dev);
 
-	return pci_dev_wait(dev, "bus reset", PCIE_RESET_READY_POLL_MS);
+	return pci_bridge_wait_for_secondary_bus(dev, "bus reset",
+						 PCIE_RESET_READY_POLL_MS);
 }
 EXPORT_SYMBOL_GPL(pci_bridge_secondary_bus_reset);
 
@@ -5059,20 +5120,21 @@
 	return pci_parent_bus_reset(dev, probe);
 }
 
-static void pci_dev_lock(struct pci_dev *dev)
+void pci_dev_lock(struct pci_dev *dev)
 {
-	pci_cfg_access_lock(dev);
 	/* block PM suspend, driver probe, etc. */
 	device_lock(&dev->dev);
+	pci_cfg_access_lock(dev);
 }
+EXPORT_SYMBOL_GPL(pci_dev_lock);
 
 /* Return 1 on successful lock, 0 on contention */
 int pci_dev_trylock(struct pci_dev *dev)
 {
-	if (pci_cfg_access_trylock(dev)) {
-		if (device_trylock(&dev->dev))
+	if (device_trylock(&dev->dev)) {
+		if (pci_cfg_access_trylock(dev))
 			return 1;
-		pci_cfg_access_unlock(dev);
+		device_unlock(&dev->dev);
 	}
 
 	return 0;
@@ -5081,8 +5143,8 @@
 
 void pci_dev_unlock(struct pci_dev *dev)
 {
-	device_unlock(&dev->dev);
 	pci_cfg_access_unlock(dev);
+	device_unlock(&dev->dev);
 }
 EXPORT_SYMBOL_GPL(pci_dev_unlock);
 
@@ -5183,7 +5245,7 @@
 				  const char *buf, size_t count)
 {
 	struct pci_dev *pdev = to_pci_dev(dev);
-	char *options, *name;
+	char *options, *tmp_options, *name;
 	int m, n;
 	u8 reset_methods[PCI_NUM_RESET_METHODS] = { 0 };
 
@@ -5203,7 +5265,8 @@
 		return -ENOMEM;
 
 	n = 0;
-	while ((name = strsep(&options, " ")) != NULL) {
+	tmp_options = options;
+	while ((name = strsep(&tmp_options, " ")) != NULL) {
 		if (sysfs_streq(name, ""))
 			continue;
 
@@ -5452,6 +5515,8 @@
 		return false;
 
 	list_for_each_entry(dev, &bus->devices, bus_list) {
+		if (!pci_reset_supported(dev))
+			return false;
 		if (dev->dev_flags & PCI_DEV_FLAGS_NO_BUS_RESET ||
 		    (dev->subordinate && !pci_bus_resetable(dev->subordinate)))
 			return false;
@@ -5465,10 +5530,12 @@
 {
 	struct pci_dev *dev;
 
+	pci_dev_lock(bus->self);
 	list_for_each_entry(dev, &bus->devices, bus_list) {
-		pci_dev_lock(dev);
 		if (dev->subordinate)
 			pci_bus_lock(dev->subordinate);
+		else
+			pci_dev_lock(dev);
 	}
 }
 
@@ -5480,8 +5547,10 @@
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		if (dev->subordinate)
 			pci_bus_unlock(dev->subordinate);
-		pci_dev_unlock(dev);
+		else
+			pci_dev_unlock(dev);
 	}
+	pci_dev_unlock(bus->self);
 }
 
 /* Return 1 on successful lock, 0 on contention */
@@ -5489,15 +5558,15 @@
 {
 	struct pci_dev *dev;
 
+	if (!pci_dev_trylock(bus->self))
+		return 0;
+
 	list_for_each_entry(dev, &bus->devices, bus_list) {
-		if (!pci_dev_trylock(dev))
-			goto unlock;
 		if (dev->subordinate) {
-			if (!pci_bus_trylock(dev->subordinate)) {
-				pci_dev_unlock(dev);
+			if (!pci_bus_trylock(dev->subordinate))
 				goto unlock;
-			}
-		}
+		} else if (!pci_dev_trylock(dev))
+			goto unlock;
 	}
 	return 1;
 
@@ -5505,8 +5574,10 @@
 	list_for_each_entry_continue_reverse(dev, &bus->devices, bus_list) {
 		if (dev->subordinate)
 			pci_bus_unlock(dev->subordinate);
-		pci_dev_unlock(dev);
+		else
+			pci_dev_unlock(dev);
 	}
+	pci_dev_unlock(bus->self);
 	return 0;
 }
 
@@ -5522,6 +5593,8 @@
 	list_for_each_entry(dev, &slot->bus->devices, bus_list) {
 		if (!dev->slot || dev->slot != slot)
 			continue;
+		if (!pci_reset_supported(dev))
+			return false;
 		if (dev->dev_flags & PCI_DEV_FLAGS_NO_BUS_RESET ||
 		    (dev->subordinate && !pci_bus_resetable(dev->subordinate)))
 			return false;
@@ -5538,9 +5611,10 @@
 	list_for_each_entry(dev, &slot->bus->devices, bus_list) {
 		if (!dev->slot || dev->slot != slot)
 			continue;
-		pci_dev_lock(dev);
 		if (dev->subordinate)
 			pci_bus_lock(dev->subordinate);
+		else
+			pci_dev_lock(dev);
 	}
 }
 
@@ -5566,14 +5640,13 @@
 	list_for_each_entry(dev, &slot->bus->devices, bus_list) {
 		if (!dev->slot || dev->slot != slot)
 			continue;
-		if (!pci_dev_trylock(dev))
-			goto unlock;
 		if (dev->subordinate) {
 			if (!pci_bus_trylock(dev->subordinate)) {
 				pci_dev_unlock(dev);
 				goto unlock;
 			}
-		}
+		} else if (!pci_dev_trylock(dev))
+			goto unlock;
 	}
 	return 1;
 
@@ -5584,7 +5657,8 @@
 			continue;
 		if (dev->subordinate)
 			pci_bus_unlock(dev->subordinate);
-		pci_dev_unlock(dev);
+		else
+			pci_dev_unlock(dev);
 	}
 	return 0;
 }
@@ -5796,7 +5870,7 @@
  *
  * Same as above except return -EAGAIN if the bus cannot be locked
  */
-static int __pci_reset_bus(struct pci_bus *bus)
+int __pci_reset_bus(struct pci_bus *bus)
 {
 	int rc;
 
@@ -5950,6 +6024,7 @@
 {
 	u16 v;
 	int ret;
+	struct pci_host_bridge *bridge = pci_find_host_bridge(dev->bus);
 
 	if (rq < 128 || rq > 4096 || !is_power_of_2(rq))
 		return -EINVAL;
@@ -5968,6 +6043,15 @@
 
 	v = (ffs(rq) - 8) << 12;
 
+	if (bridge->no_inc_mrrs) {
+		int max_mrrs = pcie_get_readrq(dev);
+
+		if (rq > max_mrrs) {
+			pci_info(dev, "can't set Max_Read_Request_Size to %d; max is %d\n", rq, max_mrrs);
+			return -EINVAL;
+		}
+	}
+
 	ret = pcie_capability_clear_and_set_word(dev, PCI_EXP_DEVCTL,
 						  PCI_EXP_DEVCTL_READRQ, v);
 
@@ -6053,8 +6137,7 @@
 		pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta);
 
 		next_speed = pcie_link_speed[lnksta & PCI_EXP_LNKSTA_CLS];
-		next_width = (lnksta & PCI_EXP_LNKSTA_NLW) >>
-			PCI_EXP_LNKSTA_NLW_SHIFT;
+		next_width = FIELD_GET(PCI_EXP_LNKSTA_NLW, lnksta);
 
 		next_bw = next_width * PCIE_SPEED2MBS_ENC(next_speed);
 
@@ -6126,7 +6209,7 @@
 
 	pcie_capability_read_dword(dev, PCI_EXP_LNKCAP, &lnkcap);
 	if (lnkcap)
-		return (lnkcap & PCI_EXP_LNKCAP_MLW) >> 4;
+		return FIELD_GET(PCI_EXP_LNKCAP_MLW, lnkcap);
 
 	return PCIE_LNK_WIDTH_UNKNOWN;
 }
@@ -6363,6 +6446,8 @@
 {
 	u32 v;
 
+	/* Check PF if pdev is a VF, since VF Vendor/Device IDs are 0xffff */
+	pdev = pci_physfn(pdev);
 	if (pci_dev_is_disconnected(pdev))
 		return false;
 	return pci_bus_read_dev_vendor_id(pdev->bus, pdev->devfn, &v, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pci.h
@@ -37,6 +37,7 @@
 void pci_init_reset_methods(struct pci_dev *dev);
 int pci_bridge_secondary_bus_reset(struct pci_dev *dev);
 int pci_bus_error_reset(struct pci_dev *dev);
+int __pci_reset_bus(struct pci_bus *bus);
 
 struct pci_cap_saved_data {
 	u16		cap_nr;
@@ -63,6 +64,19 @@
 #define PCI_PM_D3HOT_WAIT       10	/* msec */
 #define PCI_PM_D3COLD_WAIT      100	/* msec */
 
+/*
+ * Following exit from Conventional Reset, devices must be ready within 1 sec
+ * (PCIe r6.0 sec 6.6.1).  A D3cold to D0 transition implies a Conventional
+ * Reset (PCIe r6.0 sec 5.8).
+ */
+#define PCI_RESET_WAIT		1000	/* msec */
+/*
+ * Devices may extend the 1 sec period through Request Retry Status completions
+ * (PCIe r6.0 sec 2.3.1).  The spec does not provide an upper limit, but 60 sec
+ * ought to be enough for any device to become responsive.
+ */
+#define PCIE_RESET_READY_POLL_MS 60000	/* msec */
+
 /**
  * struct pci_platform_pm_ops - Firmware PM callbacks
  *
@@ -124,7 +138,9 @@
 void pci_msix_init(struct pci_dev *dev);
 bool pci_bridge_d3_possible(struct pci_dev *dev);
 void pci_bridge_d3_update(struct pci_dev *dev);
-void pci_bridge_wait_for_secondary_bus(struct pci_dev *dev);
+int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type,
+				      int timeout);
+void pci_bridge_reconfigure_ltr(struct pci_dev *dev);
 
 static inline void pci_wakeup_event(struct pci_dev *dev)
 {
@@ -271,8 +287,10 @@
 int pci_idt_bus_quirk(struct pci_bus *bus, int devfn, u32 *pl, int crs_timeout);
 
 int pci_setup_device(struct pci_dev *dev);
+void __pci_size_stdbars(struct pci_dev *dev, int count,
+			unsigned int pos, u32 *sizes);
 int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
-		    struct resource *res, unsigned int reg);
+		    struct resource *res, unsigned int reg, u32 *sizes);
 void pci_configure_ari(struct pci_dev *dev);
 void __pci_bus_size_bridges(struct pci_bus *bus,
 			struct list_head *realloc_head);
@@ -298,7 +316,7 @@
 
 /* PCIe speed to Mb/s reduced by encoding overhead */
 #define PCIE_SPEED2MBS_ENC(speed) \
-	((speed) == PCIE_SPEED_64_0GT ? 64000*128/130 : \
+	((speed) == PCIE_SPEED_64_0GT ? 64000*1/1 : \
 	 (speed) == PCIE_SPEED_32_0GT ? 32000*128/130 : \
 	 (speed) == PCIE_SPEED_16_0GT ? 16000*128/130 : \
 	 (speed) == PCIE_SPEED_8_0GT  ?  8000*128/130 : \
@@ -347,62 +365,40 @@
  * @dev: PCI device to set new error_state
  * @new: the state we want dev to be in
  *
- * Must be called with device_lock held.
+ * If the device is experiencing perm_failure, it has to remain in that state.
+ * Any other transition is allowed.
  *
  * Returns true if state has been changed to the requested state.
  */
 static inline bool pci_dev_set_io_state(struct pci_dev *dev,
 					pci_channel_state_t new)
 {
-	bool changed = false;
+	pci_channel_state_t old;
 
-	device_lock_assert(&dev->dev);
 	switch (new) {
 	case pci_channel_io_perm_failure:
-		switch (dev->error_state) {
-		case pci_channel_io_frozen:
-		case pci_channel_io_normal:
-		case pci_channel_io_perm_failure:
-			changed = true;
-			break;
-		}
-		break;
+		xchg(&dev->error_state, pci_channel_io_perm_failure);
+		return true;
 	case pci_channel_io_frozen:
-		switch (dev->error_state) {
-		case pci_channel_io_frozen:
-		case pci_channel_io_normal:
-			changed = true;
-			break;
-		}
-		break;
+		old = cmpxchg(&dev->error_state, pci_channel_io_normal,
+			      pci_channel_io_frozen);
+		return old != pci_channel_io_perm_failure;
 	case pci_channel_io_normal:
-		switch (dev->error_state) {
-		case pci_channel_io_frozen:
-		case pci_channel_io_normal:
-			changed = true;
-			break;
-		}
-		break;
+		old = cmpxchg(&dev->error_state, pci_channel_io_frozen,
+			      pci_channel_io_normal);
+		return old != pci_channel_io_perm_failure;
+	default:
+		return false;
 	}
-	if (changed)
-		dev->error_state = new;
-	return changed;
 }
 
 static inline int pci_dev_set_disconnected(struct pci_dev *dev, void *unused)
 {
-	device_lock(&dev->dev);
 	pci_dev_set_io_state(dev, pci_channel_io_perm_failure);
-	device_unlock(&dev->dev);
 
 	return 0;
 }
 
-static inline bool pci_dev_is_disconnected(const struct pci_dev *dev)
-{
-	return dev->error_state == pci_channel_io_perm_failure;
-}
-
 /* pci_dev priv_flags */
 #define PCI_DEV_ADDED 0
 #define PCI_DPC_RECOVERED 1
@@ -543,13 +539,17 @@
 #endif /* CONFIG_PCI_IOV */
 
 #ifdef CONFIG_PCIE_PTM
+void pci_ptm_init(struct pci_dev *dev);
 void pci_save_ptm_state(struct pci_dev *dev);
 void pci_restore_ptm_state(struct pci_dev *dev);
-void pci_disable_ptm(struct pci_dev *dev);
+void pci_suspend_ptm(struct pci_dev *dev);
+void pci_resume_ptm(struct pci_dev *dev);
 #else
+static inline void pci_ptm_init(struct pci_dev *dev) { }
 static inline void pci_save_ptm_state(struct pci_dev *dev) { }
 static inline void pci_restore_ptm_state(struct pci_dev *dev) { }
-static inline void pci_disable_ptm(struct pci_dev *dev) { }
+static inline void pci_suspend_ptm(struct pci_dev *dev) { }
+static inline void pci_resume_ptm(struct pci_dev *dev) { }
 #endif
 
 unsigned long pci_cardbus_resource_alignment(struct resource *);
@@ -600,11 +600,15 @@
 void pcie_aspm_exit_link_state(struct pci_dev *pdev);
 void pcie_aspm_pm_state_change(struct pci_dev *pdev);
 void pcie_aspm_powersave_config_link(struct pci_dev *pdev);
+void pci_save_aspm_l1ss_state(struct pci_dev *dev);
+void pci_restore_aspm_l1ss_state(struct pci_dev *dev);
 #else
 static inline void pcie_aspm_init_link_state(struct pci_dev *pdev) { }
 static inline void pcie_aspm_exit_link_state(struct pci_dev *pdev) { }
 static inline void pcie_aspm_pm_state_change(struct pci_dev *pdev) { }
 static inline void pcie_aspm_powersave_config_link(struct pci_dev *pdev) { }
+static inline void pci_save_aspm_l1ss_state(struct pci_dev *dev) { }
+static inline void pci_restore_aspm_l1ss_state(struct pci_dev *dev) { }
 #endif
 
 #ifdef CONFIG_PCIE_ECRC
@@ -615,12 +619,6 @@
 static inline void pcie_ecrc_get_policy(char *str) { }
 #endif
 
-#ifdef CONFIG_PCIE_PTM
-void pci_ptm_init(struct pci_dev *dev);
-#else
-static inline void pci_ptm_init(struct pci_dev *dev) { }
-#endif
-
 struct pci_dev_reset_methods {
 	u16 vendor;
 	u16 device;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/aer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/aer.c
@@ -101,6 +101,11 @@
 #define ERR_COR_ID(d)			(d & 0xffff)
 #define ERR_UNCOR_ID(d)			(d >> 16)
 
+#define AER_ERR_STATUS_MASK		(PCI_ERR_ROOT_UNCOR_RCV |	\
+					PCI_ERR_ROOT_COR_RCV |		\
+					PCI_ERR_ROOT_MULTI_COR_RCV |	\
+					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
+
 static int pcie_aer_disable;
 static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
 
@@ -533,7 +538,7 @@
 	u64 *stats = pdev->aer_stats->stats_array;			\
 	size_t len = 0;							\
 									\
-	for (i = 0; i < ARRAY_SIZE(strings_array); i++) {		\
+	for (i = 0; i < ARRAY_SIZE(pdev->aer_stats->stats_array); i++) {\
 		if (strings_array[i])					\
 			len += sysfs_emit_at(buf, len, "%s %llu\n",	\
 					     strings_array[i],		\
@@ -738,7 +743,7 @@
 	u8 bus = info->id >> 8;
 	u8 devfn = info->id & 0xff;
 
-	pci_info(dev, "%s%s error received: %04x:%02x:%02x.%d\n",
+	pci_info(dev, "%s%s error message received from %04x:%02x:%02x.%d\n",
 		 info->multi_error_valid ? "Multiple " : "",
 		 aer_error_severity_string[info->severity],
 		 pci_domain_nr(dev->bus), bus, PCI_SLOT(devfn),
@@ -926,7 +931,12 @@
 		pci_walk_bus(parent->subordinate, find_device_iter, e_info);
 
 	if (!e_info->error_dev_num) {
-		pci_info(parent, "can't find device of ID%04x\n", e_info->id);
+		u8 bus = e_info->id >> 8;
+		u8 devfn = e_info->id & 0xff;
+
+		pci_info(parent, "found no error details for %04x:%02x:%02x.%d\n",
+			 pci_domain_nr(parent->bus), bus, PCI_SLOT(devfn),
+			 PCI_FUNC(devfn));
 		return false;
 	}
 	return true;
@@ -1196,7 +1206,7 @@
 	struct aer_err_source e_src = {};
 
 	pci_read_config_dword(rp, aer + PCI_ERR_ROOT_STATUS, &e_src.status);
-	if (!(e_src.status & (PCI_ERR_ROOT_UNCOR_RCV|PCI_ERR_ROOT_COR_RCV)))
+	if (!(e_src.status & AER_ERR_STATUS_MASK))
 		return IRQ_NONE;
 
 	pci_read_config_dword(rp, aer + PCI_ERR_ROOT_ERR_SRC, &e_src.id);
@@ -1342,6 +1352,11 @@
 	struct device *device = &dev->device;
 	struct pci_dev *port = dev->port;
 
+	BUILD_BUG_ON(ARRAY_SIZE(aer_correctable_error_string) <
+		     AER_MAX_TYPEOF_COR_ERRS);
+	BUILD_BUG_ON(ARRAY_SIZE(aer_uncorrectable_error_string) <
+		     AER_MAX_TYPEOF_UNCOR_ERRS);
+
 	/* Limit to Root Ports or Root Complex Event Collectors */
 	if ((pci_pcie_type(port) != PCI_EXP_TYPE_RC_EC) &&
 	    (pci_pcie_type(port) != PCI_EXP_TYPE_ROOT_PORT))
@@ -1367,6 +1382,22 @@
 	return 0;
 }
 
+static int aer_suspend(struct pcie_device *dev)
+{
+	struct aer_rpc *rpc = get_service_data(dev);
+
+	aer_disable_rootport(rpc);
+	return 0;
+}
+
+static int aer_resume(struct pcie_device *dev)
+{
+	struct aer_rpc *rpc = get_service_data(dev);
+
+	aer_enable_rootport(rpc);
+	return 0;
+}
+
 /**
  * aer_root_reset - reset Root Port hierarchy, RCEC, or RCiEP
  * @dev: pointer to Root Port, RCEC, or RCiEP
@@ -1438,6 +1469,8 @@
 	.service	= PCIE_PORT_SERVICE_AER,
 
 	.probe		= aer_probe,
+	.suspend	= aer_suspend,
+	.resume		= aer_resume,
 	.remove		= aer_remove,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/aspm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/aspm.c
@@ -192,12 +192,39 @@
 	link->clkpm_disable = blacklist ? 1 : 0;
 }
 
-static bool pcie_retrain_link(struct pcie_link_state *link)
+static int pcie_wait_for_retrain(struct pci_dev *pdev)
 {
-	struct pci_dev *parent = link->pdev;
 	unsigned long end_jiffies;
 	u16 reg16;
 
+	/* Wait for Link Training to be cleared by hardware */
+	end_jiffies = jiffies + LINK_RETRAIN_TIMEOUT;
+	do {
+		pcie_capability_read_word(pdev, PCI_EXP_LNKSTA, &reg16);
+		if (!(reg16 & PCI_EXP_LNKSTA_LT))
+			return 0;
+		msleep(1);
+	} while (time_before(jiffies, end_jiffies));
+
+	return -ETIMEDOUT;
+}
+
+static int pcie_retrain_link(struct pcie_link_state *link)
+{
+	struct pci_dev *parent = link->pdev;
+	int rc;
+	u16 reg16;
+
+	/*
+	 * Ensure the updated LNKCTL parameters are used during link
+	 * training by checking that there is no ongoing link training to
+	 * avoid LTSSM race as recommended in Implementation Note at the
+	 * end of PCIe r6.0.1 sec 7.5.3.7.
+	 */
+	rc = pcie_wait_for_retrain(parent);
+	if (rc)
+		return rc;
+
 	pcie_capability_read_word(parent, PCI_EXP_LNKCTL, &reg16);
 	reg16 |= PCI_EXP_LNKCTL_RL;
 	pcie_capability_write_word(parent, PCI_EXP_LNKCTL, reg16);
@@ -211,15 +238,7 @@
 		pcie_capability_write_word(parent, PCI_EXP_LNKCTL, reg16);
 	}
 
-	/* Wait for link training end. Break out after waiting for timeout */
-	end_jiffies = jiffies + LINK_RETRAIN_TIMEOUT;
-	do {
-		pcie_capability_read_word(parent, PCI_EXP_LNKSTA, &reg16);
-		if (!(reg16 & PCI_EXP_LNKSTA_LT))
-			break;
-		msleep(1);
-	} while (time_before(jiffies, end_jiffies));
-	return !(reg16 & PCI_EXP_LNKSTA_LT);
+	return pcie_wait_for_retrain(parent);
 }
 
 /*
@@ -230,7 +249,7 @@
 static void pcie_aspm_configure_common_clock(struct pcie_link_state *link)
 {
 	int same_clock = 1;
-	u16 reg16, parent_reg, child_reg[8];
+	u16 reg16, ccc, parent_old_ccc, child_old_ccc[8];
 	struct pci_dev *child, *parent = link->pdev;
 	struct pci_bus *linkbus = parent->subordinate;
 	/*
@@ -252,6 +271,7 @@
 
 	/* Port might be already in common clock mode */
 	pcie_capability_read_word(parent, PCI_EXP_LNKCTL, &reg16);
+	parent_old_ccc = reg16 & PCI_EXP_LNKCTL_CCC;
 	if (same_clock && (reg16 & PCI_EXP_LNKCTL_CCC)) {
 		bool consistent = true;
 
@@ -268,35 +288,30 @@
 		pci_info(parent, "ASPM: current common clock configuration is inconsistent, reconfiguring\n");
 	}
 
+	ccc = same_clock ? PCI_EXP_LNKCTL_CCC : 0;
 	/* Configure downstream component, all functions */
 	list_for_each_entry(child, &linkbus->devices, bus_list) {
 		pcie_capability_read_word(child, PCI_EXP_LNKCTL, &reg16);
-		child_reg[PCI_FUNC(child->devfn)] = reg16;
-		if (same_clock)
-			reg16 |= PCI_EXP_LNKCTL_CCC;
-		else
-			reg16 &= ~PCI_EXP_LNKCTL_CCC;
-		pcie_capability_write_word(child, PCI_EXP_LNKCTL, reg16);
+		child_old_ccc[PCI_FUNC(child->devfn)] = reg16 & PCI_EXP_LNKCTL_CCC;
+		pcie_capability_clear_and_set_word(child, PCI_EXP_LNKCTL,
+						   PCI_EXP_LNKCTL_CCC, ccc);
 	}
 
 	/* Configure upstream component */
-	pcie_capability_read_word(parent, PCI_EXP_LNKCTL, &reg16);
-	parent_reg = reg16;
-	if (same_clock)
-		reg16 |= PCI_EXP_LNKCTL_CCC;
-	else
-		reg16 &= ~PCI_EXP_LNKCTL_CCC;
-	pcie_capability_write_word(parent, PCI_EXP_LNKCTL, reg16);
+	pcie_capability_clear_and_set_word(parent, PCI_EXP_LNKCTL,
+					   PCI_EXP_LNKCTL_CCC, ccc);
 
-	if (pcie_retrain_link(link))
-		return;
+	if (pcie_retrain_link(link)) {
 
-	/* Training failed. Restore common clock configurations */
-	pci_err(parent, "ASPM: Could not configure common clock\n");
-	list_for_each_entry(child, &linkbus->devices, bus_list)
-		pcie_capability_write_word(child, PCI_EXP_LNKCTL,
-					   child_reg[PCI_FUNC(child->devfn)]);
-	pcie_capability_write_word(parent, PCI_EXP_LNKCTL, parent_reg);
+		/* Training failed. Restore common clock configurations */
+		pci_err(parent, "ASPM: Could not configure common clock\n");
+		list_for_each_entry(child, &linkbus->devices, bus_list)
+			pcie_capability_clear_and_set_word(child, PCI_EXP_LNKCTL,
+							   PCI_EXP_LNKCTL_CCC,
+							   child_old_ccc[PCI_FUNC(child->devfn)]);
+		pcie_capability_clear_and_set_word(parent, PCI_EXP_LNKCTL,
+						   PCI_EXP_LNKCTL_CCC, parent_old_ccc);
+	}
 }
 
 /* Convert L0s latency encoding to ns */
@@ -653,7 +668,8 @@
 		aspm_calc_l1ss_info(link, parent_l1ss_cap, child_l1ss_cap);
 
 	/* Save default state */
-	link->aspm_default = link->aspm_enabled;
+	link->aspm_default = parent->dev_flags & PCI_DEV_FLAGS_ENABLE_ASPM ?
+			     ASPM_STATE_ALL : link->aspm_enabled;
 
 	/* Setup initial capable state. Will be updated later */
 	link->aspm_capable = link->aspm_support;
@@ -734,6 +750,50 @@
 				PCI_L1SS_CTL1_L1SS_MASK, val);
 }
 
+void pci_save_aspm_l1ss_state(struct pci_dev *dev)
+{
+	int aspm_l1ss;
+	struct pci_cap_saved_state *save_state;
+	u32 *cap;
+
+	if (!pci_is_pcie(dev))
+		return;
+
+	aspm_l1ss = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_L1SS);
+	if (!aspm_l1ss)
+		return;
+
+	save_state = pci_find_saved_ext_cap(dev, PCI_EXT_CAP_ID_L1SS);
+	if (!save_state)
+		return;
+
+	cap = (u32 *)&save_state->cap.data[0];
+	pci_read_config_dword(dev, aspm_l1ss + PCI_L1SS_CTL2, cap++);
+	pci_read_config_dword(dev, aspm_l1ss + PCI_L1SS_CTL1, cap++);
+}
+
+void pci_restore_aspm_l1ss_state(struct pci_dev *dev)
+{
+	int aspm_l1ss;
+	struct pci_cap_saved_state *save_state;
+	u32 *cap;
+
+	if (!pci_is_pcie(dev))
+		return;
+
+	aspm_l1ss = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_L1SS);
+	if (!aspm_l1ss)
+		return;
+
+	save_state = pci_find_saved_ext_cap(dev, PCI_EXT_CAP_ID_L1SS);
+	if (!save_state)
+		return;
+
+	cap = (u32 *)&save_state->cap.data[0];
+	pci_write_config_dword(dev, aspm_l1ss + PCI_L1SS_CTL2, *cap++);
+	pci_write_config_dword(dev, aspm_l1ss + PCI_L1SS_CTL1, *cap++);
+}
+
 static void pcie_config_aspm_dev(struct pci_dev *pdev, u32 val)
 {
 	pcie_capability_clear_and_set_word(pdev, PCI_EXP_LNKCTL,
@@ -993,21 +1053,24 @@
 
 	down_read(&pci_bus_sem);
 	mutex_lock(&aspm_lock);
-	/*
-	 * All PCIe functions are in one slot, remove one function will remove
-	 * the whole slot, so just wait until we are the last function left.
-	 */
-	if (!list_empty(&parent->subordinate->devices))
-		goto out;
 
 	link = parent->link_state;
 	root = link->root;
 	parent_link = link->parent;
 
-	/* All functions are removed, so just disable ASPM for the link */
+	/*
+	 * Free the parent link state, no later than function 0 (i.e.
+	 * link->downstream) being removed.
+	 *
+	 * Do not free the link state any earlier. If function 0 is a
+	 * switch upstream port, this link state is parent_link to all
+	 * subordinate ones.
+	 */
+	if (pdev != link->downstream)
+		goto out;
+
 	pcie_config_aspm_link(link, 0);
 	list_del(&link->sibling);
-	/* Clock PM is for endpoint device */
 	free_link_state(link);
 
 	/* Recheck latencies and configure upstream links */
@@ -1015,7 +1078,8 @@
 		pcie_update_aspm_capable(root);
 		pcie_config_aspm_path(parent_link);
 	}
-out:
+
+ out:
 	mutex_unlock(&aspm_lock);
 	up_read(&pci_bus_sem);
 }
@@ -1201,6 +1265,17 @@
 }
 EXPORT_SYMBOL_GPL(pcie_aspm_enabled);
 
+bool pcie_aspm_capable(struct pci_dev *pdev)
+{
+	struct pcie_link_state *link = pcie_aspm_get_link(pdev);
+
+	if (!link)
+		return false;
+
+	return link->aspm_capable;
+}
+EXPORT_SYMBOL_GPL(pcie_aspm_capable);
+
 static ssize_t aspm_attr_show_common(struct device *dev,
 				     struct device_attribute *attr,
 				     char *buf, u8 state)
@@ -1232,6 +1307,8 @@
 			link->aspm_disable &= ~ASPM_STATE_L1;
 	} else {
 		link->aspm_disable |= state;
+		if (state & ASPM_STATE_L1)
+			link->aspm_disable |= ASPM_STATE_L1SS;
 	}
 
 	pcie_config_aspm_link(link, policy_to_aspm_state(link));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/dpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/dpc.c
@@ -170,8 +170,8 @@
 	pci_write_config_word(pdev, cap + PCI_EXP_DPC_STATUS,
 			      PCI_EXP_DPC_STATUS_TRIGGER);
 
-	if (!pcie_wait_for_link(pdev, true)) {
-		pci_info(pdev, "Data Link Layer Link Active not set in 1000 msec\n");
+	if (pci_bridge_wait_for_secondary_bus(pdev, "DPC",
+					      PCIE_RESET_READY_POLL_MS)) {
 		clear_bit(PCI_DPC_RECOVERED, &pdev->priv_flags);
 		ret = PCI_ERS_RESULT_DISCONNECT;
 	} else {
@@ -231,7 +231,7 @@
 
 	for (i = 0; i < pdev->dpc_rp_log_size - 5; i++) {
 		pci_read_config_dword(pdev,
-			cap + PCI_EXP_DPC_RP_PIO_TLPPREFIX_LOG, &prefix);
+			cap + PCI_EXP_DPC_RP_PIO_TLPPREFIX_LOG + i * 4, &prefix);
 		pci_err(pdev, "TLP Prefix Header: dw%d, %#010x\n", i, prefix);
 	}
  clear_status:
@@ -335,21 +335,47 @@
 		return;
 
 	pdev->dpc_rp_extensions = true;
-	pdev->dpc_rp_log_size = (cap & PCI_EXP_DPC_RP_PIO_LOG_SIZE) >> 8;
-	if (pdev->dpc_rp_log_size < 4 || pdev->dpc_rp_log_size > 9) {
-		pci_err(pdev, "RP PIO log size %u is invalid\n",
-			pdev->dpc_rp_log_size);
-		pdev->dpc_rp_log_size = 0;
+
+	/* Quirks may set dpc_rp_log_size if device or firmware is buggy */
+	if (!pdev->dpc_rp_log_size) {
+		pdev->dpc_rp_log_size =
+			(cap & PCI_EXP_DPC_RP_PIO_LOG_SIZE) >> 8;
+		if (pdev->dpc_rp_log_size < 4 || pdev->dpc_rp_log_size > 9) {
+			pci_err(pdev, "RP PIO log size %u is invalid\n",
+				pdev->dpc_rp_log_size);
+			pdev->dpc_rp_log_size = 0;
+		}
 	}
 }
 
+static void dpc_enable(struct pcie_device *dev)
+{
+	struct pci_dev *pdev = dev->port;
+	u16 ctl;
+
+	pci_read_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, &ctl);
+
+	ctl = (ctl & 0xfff4) | PCI_EXP_DPC_CTL_EN_FATAL | PCI_EXP_DPC_CTL_INT_EN;
+	pci_write_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, ctl);
+}
+
+static void dpc_disable(struct pcie_device *dev)
+{
+	struct pci_dev *pdev = dev->port;
+	u16 ctl;
+
+	pci_read_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, &ctl);
+	ctl &= ~(PCI_EXP_DPC_CTL_EN_FATAL | PCI_EXP_DPC_CTL_INT_EN);
+	pci_write_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, ctl);
+}
+
 #define FLAG(x, y) (((x) & (y)) ? '+' : '-')
 static int dpc_probe(struct pcie_device *dev)
 {
 	struct pci_dev *pdev = dev->port;
 	struct device *device = &dev->device;
 	int status;
-	u16 ctl, cap;
+	u16 cap;
 
 	if (!pcie_aer_is_native(pdev) && !pcie_ports_dpc_native)
 		return -ENOTSUPP;
@@ -364,10 +390,7 @@
 	}
 
 	pci_read_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CAP, &cap);
-	pci_read_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, &ctl);
-
-	ctl = (ctl & 0xfff4) | PCI_EXP_DPC_CTL_EN_FATAL | PCI_EXP_DPC_CTL_INT_EN;
-	pci_write_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, ctl);
+	dpc_enable(dev);
 	pci_info(pdev, "enabled with IRQ %d\n", dev->irq);
 
 	pci_info(pdev, "error containment capabilities: Int Msg #%d, RPExt%c PoisonedTLP%c SwTrigger%c RP PIO Log %d, DL_ActiveErr%c\n",
@@ -380,14 +403,21 @@
 	return status;
 }
 
-static void dpc_remove(struct pcie_device *dev)
+static int dpc_suspend(struct pcie_device *dev)
 {
-	struct pci_dev *pdev = dev->port;
-	u16 ctl;
+	dpc_disable(dev);
+	return 0;
+}
 
-	pci_read_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, &ctl);
-	ctl &= ~(PCI_EXP_DPC_CTL_EN_FATAL | PCI_EXP_DPC_CTL_INT_EN);
-	pci_write_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_CTL, ctl);
+static int dpc_resume(struct pcie_device *dev)
+{
+	dpc_enable(dev);
+	return 0;
+}
+
+static void dpc_remove(struct pcie_device *dev)
+{
+	dpc_disable(dev);
 }
 
 static struct pcie_port_service_driver dpcdriver = {
@@ -395,6 +425,8 @@
 	.port_type	= PCIE_ANY_PORT,
 	.service	= PCIE_PORT_SERVICE_DPC,
 	.probe		= dpc_probe,
+	.suspend	= dpc_suspend,
+	.resume		= dpc_resume,
 	.remove		= dpc_remove,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/edr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/edr.c
@@ -32,10 +32,10 @@
 	int status = 0;
 
 	/*
-	 * Behavior when calling unsupported _DSM functions is undefined,
-	 * so check whether EDR_PORT_DPC_ENABLE_DSM is supported.
+	 * Per PCI Firmware r3.3, sec 4.6.12, EDR_PORT_DPC_ENABLE_DSM is
+	 * optional. Return success if it's not implemented.
 	 */
-	if (!acpi_check_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
+	if (!acpi_check_dsm(adev->handle, &pci_acpi_dsm_guid, 6,
 			    1ULL << EDR_PORT_DPC_ENABLE_DSM))
 		return 0;
 
@@ -46,12 +46,7 @@
 	argv4.package.count = 1;
 	argv4.package.elements = &req;
 
-	/*
-	 * Per Downstream Port Containment Related Enhancements ECN to PCI
-	 * Firmware Specification r3.2, sec 4.6.12, EDR_PORT_DPC_ENABLE_DSM is
-	 * optional.  Return success if it's not implemented.
-	 */
-	obj = acpi_evaluate_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
+	obj = acpi_evaluate_dsm(adev->handle, &pci_acpi_dsm_guid, 6,
 				EDR_PORT_DPC_ENABLE_DSM, &argv4);
 	if (!obj)
 		return 0;
@@ -85,8 +80,9 @@
 	u16 port;
 
 	/*
-	 * Behavior when calling unsupported _DSM functions is undefined,
-	 * so check whether EDR_PORT_DPC_ENABLE_DSM is supported.
+	 * If EDR_PORT_LOCATE_DSM is not implemented under the target of
+	 * EDR, the target is the port that experienced the containment
+	 * event (PCI Firmware r3.3, sec 4.6.13).
 	 */
 	if (!acpi_check_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
 			    1ULL << EDR_PORT_LOCATE_DSM))
@@ -104,6 +100,16 @@
 	}
 
 	/*
+	 * Bit 31 represents the success/failure of the operation. If bit
+	 * 31 is set, the operation failed.
+	 */
+	if (obj->integer.value & BIT(31)) {
+		ACPI_FREE(obj);
+		pci_err(pdev, "Locate Port _DSM failed\n");
+		return NULL;
+	}
+
+	/*
 	 * Firmware returns DPC port BDF details in following format:
 	 *	15:8 = bus
 	 *	 7:3 = device
@@ -193,6 +199,7 @@
 	 */
 	if (estate == PCI_ERS_RESULT_RECOVERED) {
 		pci_dbg(edev, "DPC port successfully recovered\n");
+		pcie_clear_device_status(edev);
 		acpi_send_edr_status(pdev, edev, EDR_OST_SUCCESS);
 	} else {
 		pci_dbg(edev, "DPC port recovery failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/err.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/err.c
@@ -13,6 +13,7 @@
 #define dev_fmt(fmt) "AER: " fmt
 
 #include <linux/pci.h>
+#include <linux/pm_runtime.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/errno.h>
@@ -79,6 +80,18 @@
 	return 0;
 }
 
+static int pci_pm_runtime_get_sync(struct pci_dev *pdev, void *data)
+{
+	pm_runtime_get_sync(&pdev->dev);
+	return 0;
+}
+
+static int pci_pm_runtime_put(struct pci_dev *pdev, void *data)
+{
+	pm_runtime_put(&pdev->dev);
+	return 0;
+}
+
 static int report_frozen_detected(struct pci_dev *dev, void *data)
 {
 	return report_error_detected(dev, pci_channel_io_frozen, data);
@@ -195,6 +208,8 @@
 	else
 		bridge = pci_upstream_bridge(dev);
 
+	pci_walk_bridge(bridge, pci_pm_runtime_get_sync, NULL);
+
 	pci_dbg(bridge, "broadcast error_detected message\n");
 	if (state == pci_channel_io_frozen) {
 		pci_walk_bridge(bridge, report_frozen_detected, &status);
@@ -239,10 +254,15 @@
 		pcie_clear_device_status(dev);
 		pci_aer_clear_nonfatal_status(dev);
 	}
+
+	pci_walk_bridge(bridge, pci_pm_runtime_put, NULL);
+
 	pci_info(bridge, "device recovery successful\n");
 	return status;
 
 failed:
+	pci_walk_bridge(bridge, pci_pm_runtime_put, NULL);
+
 	pci_uevent_ers(bridge, PCI_ERS_RESULT_DISCONNECT);
 
 	/* TODO: Should kernel panic here? */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/portdrv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/portdrv.h
@@ -85,6 +85,8 @@
 	int (*runtime_suspend)(struct pcie_device *dev);
 	int (*runtime_resume)(struct pcie_device *dev);
 
+	int (*slot_reset)(struct pcie_device *dev);
+
 	/* Device driver may resume normal operations */
 	void (*error_resume)(struct pci_dev *dev);
 
@@ -110,6 +112,7 @@
 
 extern struct bus_type pcie_port_bus_type;
 int pcie_port_device_register(struct pci_dev *dev);
+int pcie_port_device_iter(struct device *dev, void *data);
 #ifdef CONFIG_PM
 int pcie_port_device_suspend(struct device *dev);
 int pcie_port_device_resume_noirq(struct device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/portdrv_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/portdrv_core.c
@@ -214,10 +214,12 @@
 
 		/*
 		 * Disable hot-plug interrupts in case they have been enabled
-		 * by the BIOS and the hot-plug service driver is not loaded.
+		 * by the BIOS and the hot-plug service driver won't be loaded
+		 * to handle them.
 		 */
-		pcie_capability_clear_word(dev, PCI_EXP_SLTCTL,
-			  PCI_EXP_SLTCTL_CCIE | PCI_EXP_SLTCTL_HPIE);
+		if (!IS_ENABLED(CONFIG_HOTPLUG_PCI_PCIE))
+			pcie_capability_clear_word(dev, PCI_EXP_SLTCTL,
+				PCI_EXP_SLTCTL_CCIE | PCI_EXP_SLTCTL_HPIE);
 	}
 
 #ifdef CONFIG_PCIEAER
@@ -367,24 +369,24 @@
 	return status;
 }
 
-#ifdef CONFIG_PM
-typedef int (*pcie_pm_callback_t)(struct pcie_device *);
+typedef int (*pcie_callback_t)(struct pcie_device *);
 
-static int pm_iter(struct device *dev, void *data)
+int pcie_port_device_iter(struct device *dev, void *data)
 {
 	struct pcie_port_service_driver *service_driver;
 	size_t offset = *(size_t *)data;
-	pcie_pm_callback_t cb;
+	pcie_callback_t cb;
 
 	if ((dev->bus == &pcie_port_bus_type) && dev->driver) {
 		service_driver = to_service_driver(dev->driver);
-		cb = *(pcie_pm_callback_t *)((void *)service_driver + offset);
+		cb = *(pcie_callback_t *)((void *)service_driver + offset);
 		if (cb)
 			return cb(to_pcie_device(dev));
 	}
 	return 0;
 }
 
+#ifdef CONFIG_PM
 /**
  * pcie_port_device_suspend - suspend port services associated with a PCIe port
  * @dev: PCI Express port to handle
@@ -392,13 +394,13 @@
 int pcie_port_device_suspend(struct device *dev)
 {
 	size_t off = offsetof(struct pcie_port_service_driver, suspend);
-	return device_for_each_child(dev, &off, pm_iter);
+	return device_for_each_child(dev, &off, pcie_port_device_iter);
 }
 
 int pcie_port_device_resume_noirq(struct device *dev)
 {
 	size_t off = offsetof(struct pcie_port_service_driver, resume_noirq);
-	return device_for_each_child(dev, &off, pm_iter);
+	return device_for_each_child(dev, &off, pcie_port_device_iter);
 }
 
 /**
@@ -408,7 +410,7 @@
 int pcie_port_device_resume(struct device *dev)
 {
 	size_t off = offsetof(struct pcie_port_service_driver, resume);
-	return device_for_each_child(dev, &off, pm_iter);
+	return device_for_each_child(dev, &off, pcie_port_device_iter);
 }
 
 /**
@@ -418,7 +420,7 @@
 int pcie_port_device_runtime_suspend(struct device *dev)
 {
 	size_t off = offsetof(struct pcie_port_service_driver, runtime_suspend);
-	return device_for_each_child(dev, &off, pm_iter);
+	return device_for_each_child(dev, &off, pcie_port_device_iter);
 }
 
 /**
@@ -428,7 +430,7 @@
 int pcie_port_device_runtime_resume(struct device *dev)
 {
 	size_t off = offsetof(struct pcie_port_service_driver, runtime_resume);
-	return device_for_each_child(dev, &off, pm_iter);
+	return device_for_each_child(dev, &off, pcie_port_device_iter);
 }
 #endif /* PM */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/portdrv_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/portdrv_pci.c
@@ -160,6 +160,9 @@
 
 static pci_ers_result_t pcie_portdrv_slot_reset(struct pci_dev *dev)
 {
+	size_t off = offsetof(struct pcie_port_service_driver, slot_reset);
+	device_for_each_child(&dev->dev, &off, pcie_port_device_iter);
+
 	pci_restore_state(dev);
 	pci_save_state(dev);
 	return PCI_ERS_RESULT_RECOVERED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/pcie/ptm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/pcie/ptm.c
@@ -9,30 +9,38 @@
 #include <linux/pci.h>
 #include "../pci.h"
 
-static void pci_ptm_info(struct pci_dev *dev)
+/*
+ * If the next upstream device supports PTM, return it; otherwise return
+ * NULL.  PTM Messages are local, so both link partners must support it.
+ */
+static struct pci_dev *pci_upstream_ptm(struct pci_dev *dev)
 {
-	char clock_desc[8];
+	struct pci_dev *ups = pci_upstream_bridge(dev);
 
-	switch (dev->ptm_granularity) {
-	case 0:
-		snprintf(clock_desc, sizeof(clock_desc), "unknown");
-		break;
-	case 255:
-		snprintf(clock_desc, sizeof(clock_desc), ">254ns");
-		break;
-	default:
-		snprintf(clock_desc, sizeof(clock_desc), "%uns",
-			 dev->ptm_granularity);
-		break;
-	}
-	pci_info(dev, "PTM enabled%s, %s granularity\n",
-		 dev->ptm_root ? " (root)" : "", clock_desc);
+	/*
+	 * Switch Downstream Ports are not permitted to have a PTM
+	 * capability; their PTM behavior is controlled by the Upstream
+	 * Port (PCIe r5.0, sec 7.9.16), so if the upstream bridge is a
+	 * Switch Downstream Port, look up one more level.
+	 */
+	if (ups && pci_pcie_type(ups) == PCI_EXP_TYPE_DOWNSTREAM)
+		ups = pci_upstream_bridge(ups);
+
+	if (ups && ups->ptm_cap)
+		return ups;
+
+	return NULL;
 }
 
-void pci_disable_ptm(struct pci_dev *dev)
+/*
+ * Find the PTM Capability (if present) and extract the information we need
+ * to use it.
+ */
+void pci_ptm_init(struct pci_dev *dev)
 {
-	int ptm;
-	u16 ctrl;
+	u16 ptm;
+	u32 cap;
+	struct pci_dev *ups;
 
 	if (!pci_is_pcie(dev))
 		return;
@@ -41,21 +49,47 @@
 	if (!ptm)
 		return;
 
-	pci_read_config_word(dev, ptm + PCI_PTM_CTRL, &ctrl);
-	ctrl &= ~(PCI_PTM_CTRL_ENABLE | PCI_PTM_CTRL_ROOT);
-	pci_write_config_word(dev, ptm + PCI_PTM_CTRL, ctrl);
+	dev->ptm_cap = ptm;
+	pci_add_ext_cap_save_buffer(dev, PCI_EXT_CAP_ID_PTM, sizeof(u32));
+
+	pci_read_config_dword(dev, ptm + PCI_PTM_CAP, &cap);
+	dev->ptm_granularity = (cap & PCI_PTM_GRANULARITY_MASK) >> 8;
+
+	/*
+	 * Per the spec recommendation (PCIe r6.0, sec 7.9.15.3), select the
+	 * furthest upstream Time Source as the PTM Root.  For Endpoints,
+	 * "the Effective Granularity is the maximum Local Clock Granularity
+	 * reported by the PTM Root and all intervening PTM Time Sources."
+	 */
+	ups = pci_upstream_ptm(dev);
+	if (ups) {
+		if (ups->ptm_granularity == 0)
+			dev->ptm_granularity = 0;
+		else if (ups->ptm_granularity > dev->ptm_granularity)
+			dev->ptm_granularity = ups->ptm_granularity;
+	} else if (cap & PCI_PTM_CAP_ROOT) {
+		dev->ptm_root = 1;
+	} else if (pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END) {
+
+		/*
+		 * Per sec 7.9.15.3, this should be the Local Clock
+		 * Granularity of the associated Time Source.  But it
+		 * doesn't say how to find that Time Source.
+		 */
+		dev->ptm_granularity = 0;
+	}
+
+	if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
+	    pci_pcie_type(dev) == PCI_EXP_TYPE_UPSTREAM)
+		pci_enable_ptm(dev, NULL);
 }
 
 void pci_save_ptm_state(struct pci_dev *dev)
 {
-	int ptm;
+	u16 ptm = dev->ptm_cap;
 	struct pci_cap_saved_state *save_state;
-	u16 *cap;
-
-	if (!pci_is_pcie(dev))
-		return;
+	u32 *cap;
 
-	ptm = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_PTM);
 	if (!ptm)
 		return;
 
@@ -63,146 +97,152 @@
 	if (!save_state)
 		return;
 
-	cap = (u16 *)&save_state->cap.data[0];
-	pci_read_config_word(dev, ptm + PCI_PTM_CTRL, cap);
+	cap = (u32 *)&save_state->cap.data[0];
+	pci_read_config_dword(dev, ptm + PCI_PTM_CTRL, cap);
 }
 
 void pci_restore_ptm_state(struct pci_dev *dev)
 {
+	u16 ptm = dev->ptm_cap;
 	struct pci_cap_saved_state *save_state;
-	int ptm;
-	u16 *cap;
+	u32 *cap;
 
-	if (!pci_is_pcie(dev))
+	if (!ptm)
 		return;
 
 	save_state = pci_find_saved_ext_cap(dev, PCI_EXT_CAP_ID_PTM);
-	ptm = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_PTM);
-	if (!save_state || !ptm)
+	if (!save_state)
 		return;
 
-	cap = (u16 *)&save_state->cap.data[0];
-	pci_write_config_word(dev, ptm + PCI_PTM_CTRL, *cap);
+	cap = (u32 *)&save_state->cap.data[0];
+	pci_write_config_dword(dev, ptm + PCI_PTM_CTRL, *cap);
 }
 
-void pci_ptm_init(struct pci_dev *dev)
+/* Enable PTM in the Control register if possible */
+static int __pci_enable_ptm(struct pci_dev *dev)
 {
-	int pos;
-	u32 cap, ctrl;
-	u8 local_clock;
+	u16 ptm = dev->ptm_cap;
 	struct pci_dev *ups;
+	u32 ctrl;
 
-	if (!pci_is_pcie(dev))
-		return;
-
-	/*
-	 * Enable PTM only on interior devices (root ports, switch ports,
-	 * etc.) on the assumption that it causes no link traffic until an
-	 * endpoint enables it.
-	 */
-	if ((pci_pcie_type(dev) == PCI_EXP_TYPE_ENDPOINT ||
-	     pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END))
-		return;
+	if (!ptm)
+		return -EINVAL;
 
 	/*
-	 * Switch Downstream Ports are not permitted to have a PTM
-	 * capability; their PTM behavior is controlled by the Upstream
-	 * Port (PCIe r5.0, sec 7.9.16).
+	 * A device uses local PTM Messages to request time information
+	 * from a PTM Root that's farther upstream.  Every device along the
+	 * path must support PTM and have it enabled so it can handle the
+	 * messages.  Therefore, if this device is not a PTM Root, the
+	 * upstream link partner must have PTM enabled before we can enable
+	 * PTM.
 	 */
-	ups = pci_upstream_bridge(dev);
-	if (pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM &&
-	    ups && ups->ptm_enabled) {
-		dev->ptm_granularity = ups->ptm_granularity;
-		dev->ptm_enabled = 1;
-		return;
+	if (!dev->ptm_root) {
+		ups = pci_upstream_ptm(dev);
+		if (!ups || !ups->ptm_enabled)
+			return -EINVAL;
 	}
 
-	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_PTM);
-	if (!pos)
-		return;
-
-	pci_add_ext_cap_save_buffer(dev, PCI_EXT_CAP_ID_PTM, sizeof(u16));
-
-	pci_read_config_dword(dev, pos + PCI_PTM_CAP, &cap);
-	local_clock = (cap & PCI_PTM_GRANULARITY_MASK) >> 8;
-
-	/*
-	 * There's no point in enabling PTM unless it's enabled in the
-	 * upstream device or this device can be a PTM Root itself.  Per
-	 * the spec recommendation (PCIe r3.1, sec 7.32.3), select the
-	 * furthest upstream Time Source as the PTM Root.
-	 */
-	if (ups && ups->ptm_enabled) {
-		ctrl = PCI_PTM_CTRL_ENABLE;
-		if (ups->ptm_granularity == 0)
-			dev->ptm_granularity = 0;
-		else if (ups->ptm_granularity > local_clock)
-			dev->ptm_granularity = ups->ptm_granularity;
-	} else {
-		if (cap & PCI_PTM_CAP_ROOT) {
-			ctrl = PCI_PTM_CTRL_ENABLE | PCI_PTM_CTRL_ROOT;
-			dev->ptm_root = 1;
-			dev->ptm_granularity = local_clock;
-		} else
-			return;
-	}
+	pci_read_config_dword(dev, ptm + PCI_PTM_CTRL, &ctrl);
 
+	ctrl |= PCI_PTM_CTRL_ENABLE;
+	ctrl &= ~PCI_PTM_GRANULARITY_MASK;
 	ctrl |= dev->ptm_granularity << 8;
-	pci_write_config_dword(dev, pos + PCI_PTM_CTRL, ctrl);
-	dev->ptm_enabled = 1;
+	if (dev->ptm_root)
+		ctrl |= PCI_PTM_CTRL_ROOT;
 
-	pci_ptm_info(dev);
+	pci_write_config_dword(dev, ptm + PCI_PTM_CTRL, ctrl);
+	return 0;
 }
 
+/**
+ * pci_enable_ptm() - Enable Precision Time Measurement
+ * @dev: PCI device
+ * @granularity: pointer to return granularity
+ *
+ * Enable Precision Time Measurement for @dev.  If successful and
+ * @granularity is non-NULL, return the Effective Granularity.
+ *
+ * Return: zero if successful, or -EINVAL if @dev lacks a PTM Capability or
+ * is not a PTM Root and lacks an upstream path of PTM-enabled devices.
+ */
 int pci_enable_ptm(struct pci_dev *dev, u8 *granularity)
 {
-	int pos;
-	u32 cap, ctrl;
-	struct pci_dev *ups;
-
-	if (!pci_is_pcie(dev))
-		return -EINVAL;
-
-	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_PTM);
-	if (!pos)
-		return -EINVAL;
-
-	pci_read_config_dword(dev, pos + PCI_PTM_CAP, &cap);
-	if (!(cap & PCI_PTM_CAP_REQ))
-		return -EINVAL;
+	int rc;
+	char clock_desc[8];
 
-	/*
-	 * For a PCIe Endpoint, PTM is only useful if the endpoint can
-	 * issue PTM requests to upstream devices that have PTM enabled.
-	 *
-	 * For Root Complex Integrated Endpoints, there is no upstream
-	 * device, so there must be some implementation-specific way to
-	 * associate the endpoint with a time source.
-	 */
-	if (pci_pcie_type(dev) == PCI_EXP_TYPE_ENDPOINT) {
-		ups = pci_upstream_bridge(dev);
-		if (!ups || !ups->ptm_enabled)
-			return -EINVAL;
+	rc = __pci_enable_ptm(dev);
+	if (rc)
+		return rc;
 
-		dev->ptm_granularity = ups->ptm_granularity;
-	} else if (pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END) {
-		dev->ptm_granularity = 0;
-	} else
-		return -EINVAL;
-
-	ctrl = PCI_PTM_CTRL_ENABLE;
-	ctrl |= dev->ptm_granularity << 8;
-	pci_write_config_dword(dev, pos + PCI_PTM_CTRL, ctrl);
 	dev->ptm_enabled = 1;
 
-	pci_ptm_info(dev);
-
 	if (granularity)
 		*granularity = dev->ptm_granularity;
+
+	switch (dev->ptm_granularity) {
+	case 0:
+		snprintf(clock_desc, sizeof(clock_desc), "unknown");
+		break;
+	case 255:
+		snprintf(clock_desc, sizeof(clock_desc), ">254ns");
+		break;
+	default:
+		snprintf(clock_desc, sizeof(clock_desc), "%uns",
+			 dev->ptm_granularity);
+		break;
+	}
+	pci_info(dev, "PTM enabled%s, %s granularity\n",
+		 dev->ptm_root ? " (root)" : "", clock_desc);
+
 	return 0;
 }
 EXPORT_SYMBOL(pci_enable_ptm);
 
+static void __pci_disable_ptm(struct pci_dev *dev)
+{
+	u16 ptm = dev->ptm_cap;
+	u32 ctrl;
+
+	if (!ptm)
+		return;
+
+	pci_read_config_dword(dev, ptm + PCI_PTM_CTRL, &ctrl);
+	ctrl &= ~(PCI_PTM_CTRL_ENABLE | PCI_PTM_CTRL_ROOT);
+	pci_write_config_dword(dev, ptm + PCI_PTM_CTRL, ctrl);
+}
+
+/**
+ * pci_disable_ptm() - Disable Precision Time Measurement
+ * @dev: PCI device
+ *
+ * Disable Precision Time Measurement for @dev.
+ */
+void pci_disable_ptm(struct pci_dev *dev)
+{
+	if (dev->ptm_enabled) {
+		__pci_disable_ptm(dev);
+		dev->ptm_enabled = 0;
+	}
+}
+EXPORT_SYMBOL(pci_disable_ptm);
+
+/*
+ * Disable PTM, but preserve dev->ptm_enabled so we silently re-enable it on
+ * resume if necessary.
+ */
+void pci_suspend_ptm(struct pci_dev *dev)
+{
+	if (dev->ptm_enabled)
+		__pci_disable_ptm(dev);
+}
+
+/* If PTM was enabled before suspend, re-enable it when resuming */
+void pci_resume_ptm(struct pci_dev *dev)
+{
+	if (dev->ptm_enabled)
+		__pci_enable_ptm(dev);
+}
+
 bool pcie_ptm_enabled(struct pci_dev *dev)
 {
 	if (!dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/probe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/probe.c
@@ -20,6 +20,7 @@
 #include <linux/irqdomain.h>
 #include <linux/pm_runtime.h>
 #include <linux/bitfield.h>
+#include <linux/list_sort.h>
 #include "pci.h"
 
 #define CARDBUS_LATENCY_TIMER	176	/* secondary latency timer */
@@ -166,39 +167,65 @@
 #define PCI_COMMAND_DECODE_ENABLE	(PCI_COMMAND_MEMORY | PCI_COMMAND_IO)
 
 /**
+ * __pci_size_bars - Read the raw BAR mask for a range of PCI BARs
+ * @dev: the PCI device
+ * @count: number of BARs to size
+ * @pos: starting config space position
+ * @sizes: array to store mask values
+ * @rom: indicate whether to use ROM mask, which avoids enabling ROM BARs
+ *
+ * Provided @sizes array must be sufficiently sized to store results for
+ * @count u32 BARs.  Caller is responsible for disabling decode to specified
+ * BAR range around calling this function.  This function is intended to avoid
+ * disabling decode around sizing each BAR individually, which can result in
+ * non-trivial overhead in virtualized environments with very large PCI BARs.
+ */
+static void __pci_size_bars(struct pci_dev *dev, int count,
+			    unsigned int pos, u32 *sizes, bool rom)
+{
+	u32 orig, mask = rom ? PCI_ROM_ADDRESS_MASK : ~0;
+	int i;
+
+	for (i = 0; i < count; i++, pos += 4, sizes++) {
+		pci_read_config_dword(dev, pos, &orig);
+		pci_write_config_dword(dev, pos, mask);
+		pci_read_config_dword(dev, pos, sizes);
+		pci_write_config_dword(dev, pos, orig);
+	}
+}
+
+void __pci_size_stdbars(struct pci_dev *dev, int count,
+			unsigned int pos, u32 *sizes)
+{
+	__pci_size_bars(dev, count, pos, sizes, false);
+}
+
+static void __pci_size_rom(struct pci_dev *dev, unsigned int pos, u32 *sizes)
+{
+	__pci_size_bars(dev, 1, pos, sizes, true);
+}
+
+/**
  * __pci_read_base - Read a PCI BAR
  * @dev: the PCI device
  * @type: type of the BAR
  * @res: resource buffer to be filled in
  * @pos: BAR position in the config space
+ * @sizes: array of one or more pre-read BAR masks
  *
  * Returns 1 if the BAR is 64-bit, or 0 if 32-bit.
  */
 int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
-		    struct resource *res, unsigned int pos)
+		    struct resource *res, unsigned int pos, u32 *sizes)
 {
-	u32 l = 0, sz = 0, mask;
+	u32 l = 0, sz;
 	u64 l64, sz64, mask64;
-	u16 orig_cmd;
 	struct pci_bus_region region, inverted_region;
 
-	mask = type ? PCI_ROM_ADDRESS_MASK : ~0;
-
-	/* No printks while decoding is disabled! */
-	if (!dev->mmio_always_on) {
-		pci_read_config_word(dev, PCI_COMMAND, &orig_cmd);
-		if (orig_cmd & PCI_COMMAND_DECODE_ENABLE) {
-			pci_write_config_word(dev, PCI_COMMAND,
-				orig_cmd & ~PCI_COMMAND_DECODE_ENABLE);
-		}
-	}
-
 	res->name = pci_name(dev);
 
 	pci_read_config_dword(dev, pos, &l);
-	pci_write_config_dword(dev, pos, l | mask);
-	pci_read_config_dword(dev, pos, &sz);
-	pci_write_config_dword(dev, pos, l);
+	sz = sizes[0];
 
 	/*
 	 * All bits set in sz means the device isn't working properly.
@@ -238,18 +265,13 @@
 
 	if (res->flags & IORESOURCE_MEM_64) {
 		pci_read_config_dword(dev, pos + 4, &l);
-		pci_write_config_dword(dev, pos + 4, ~0);
-		pci_read_config_dword(dev, pos + 4, &sz);
-		pci_write_config_dword(dev, pos + 4, l);
+		sz = sizes[1];
 
 		l64 |= ((u64)l << 32);
 		sz64 |= ((u64)sz << 32);
 		mask64 |= ((u64)~0 << 32);
 	}
 
-	if (!dev->mmio_always_on && (orig_cmd & PCI_COMMAND_DECODE_ENABLE))
-		pci_write_config_word(dev, PCI_COMMAND, orig_cmd);
-
 	if (!sz64)
 		goto fail;
 
@@ -321,7 +343,11 @@
 
 static void pci_read_bases(struct pci_dev *dev, unsigned int howmany, int rom)
 {
+	u32 rombar, stdbars[PCI_STD_NUM_BARS];
 	unsigned int pos, reg;
+	u16 orig_cmd;
+
+	BUILD_BUG_ON(howmany > PCI_STD_NUM_BARS);
 
 	if (dev->non_compliant_bars)
 		return;
@@ -330,10 +356,28 @@
 	if (dev->is_virtfn)
 		return;
 
+	/* No printks while decoding is disabled! */
+	if (!dev->mmio_always_on) {
+		pci_read_config_word(dev, PCI_COMMAND, &orig_cmd);
+		if (orig_cmd & PCI_COMMAND_DECODE_ENABLE) {
+			pci_write_config_word(dev, PCI_COMMAND,
+				orig_cmd & ~PCI_COMMAND_DECODE_ENABLE);
+		}
+	}
+
+	__pci_size_stdbars(dev, howmany, PCI_BASE_ADDRESS_0, stdbars);
+	if (rom)
+		__pci_size_rom(dev, rom, &rombar);
+
+	if (!dev->mmio_always_on &&
+	    (orig_cmd & PCI_COMMAND_DECODE_ENABLE))
+		pci_write_config_word(dev, PCI_COMMAND, orig_cmd);
+
 	for (pos = 0; pos < howmany; pos++) {
 		struct resource *res = &dev->resource[pos];
 		reg = PCI_BASE_ADDRESS_0 + (pos << 2);
-		pos += __pci_read_base(dev, pci_bar_unknown, res, reg);
+		pos += __pci_read_base(dev, pci_bar_unknown,
+				       res, reg, &stdbars[pos]);
 	}
 
 	if (rom) {
@@ -341,7 +385,7 @@
 		dev->rom_base_reg = rom;
 		res->flags = IORESOURCE_MEM | IORESOURCE_PREFETCH |
 				IORESOURCE_READONLY | IORESOURCE_SIZEALIGN;
-		__pci_read_base(dev, pci_bar_mem32, res, rom);
+		__pci_read_base(dev, pci_bar_mem32, res, rom, &rombar);
 	}
 }
 
@@ -880,14 +924,31 @@
 	dev_set_msi_domain(&bus->dev, d);
 }
 
+static int res_cmp(void *priv, const struct list_head *a,
+		   const struct list_head *b)
+{
+	struct resource_entry *entry1, *entry2;
+
+	entry1 = container_of(a, struct resource_entry, node);
+	entry2 = container_of(b, struct resource_entry, node);
+
+	if (entry1->res->flags != entry2->res->flags)
+		return entry1->res->flags > entry2->res->flags;
+
+	if (entry1->offset != entry2->offset)
+		return entry1->offset > entry2->offset;
+
+	return entry1->res->start > entry2->res->start;
+}
+
 static int pci_register_host_bridge(struct pci_host_bridge *bridge)
 {
 	struct device *parent = bridge->dev.parent;
-	struct resource_entry *window, *n;
+	struct resource_entry *window, *next, *n;
 	struct pci_bus *bus, *b;
-	resource_size_t offset;
+	resource_size_t offset, next_offset;
 	LIST_HEAD(resources);
-	struct resource *res;
+	struct resource *res, *next_res;
 	char addr[64], *fmt;
 	const char *name;
 	int err;
@@ -926,10 +987,9 @@
 		goto free;
 
 	err = device_add(&bridge->dev);
-	if (err) {
-		put_device(&bridge->dev);
+	if (err)
 		goto free;
-	}
+
 	bus->bridge = get_device(&bridge->dev);
 	device_enable_async_suspend(bus->bridge);
 	pci_set_bus_of_node(bus);
@@ -970,11 +1030,35 @@
 	if (nr_node_ids > 1 && pcibus_to_node(bus) == NUMA_NO_NODE)
 		dev_warn(&bus->dev, "Unknown NUMA node; performance will be reduced\n");
 
+	/* Sort and coalesce contiguous windows */
+	list_sort(NULL, &resources, res_cmp);
+	resource_list_for_each_entry_safe(window, n, &resources) {
+		if (list_is_last(&window->node, &resources))
+			break;
+
+		next = list_next_entry(window, node);
+		offset = window->offset;
+		res = window->res;
+		next_offset = next->offset;
+		next_res = next->res;
+
+		if (res->flags != next_res->flags || offset != next_offset)
+			continue;
+
+		if (res->end + 1 == next_res->start) {
+			next_res->start = res->start;
+			res->flags = res->start = res->end = 0;
+		}
+	}
+
 	/* Add initial resources to the bus */
 	resource_list_for_each_entry_safe(window, n, &resources) {
-		list_move_tail(&window->node, &bridge->windows);
 		offset = window->offset;
 		res = window->res;
+		if (!res->end)
+			continue;
+
+		list_move_tail(&window->node, &bridge->windows);
 
 		if (res->flags & IORESOURCE_BUS)
 			pci_bus_insert_busn_res(bus, bus->number, res->end);
@@ -1274,7 +1358,7 @@
 
 	if ((secondary || subordinate) && !pcibios_assign_all_busses() &&
 	    !is_cardbus && !broken) {
-		unsigned int cmax;
+		unsigned int cmax, buses;
 
 		/*
 		 * Bus already configured by firmware, process it in the
@@ -1299,7 +1383,8 @@
 			child->bridge_ctl = bctl;
 		}
 
-		cmax = pci_scan_child_bus(child);
+		buses = subordinate - secondary;
+		cmax = pci_scan_child_bus_extend(child, buses);
 		if (cmax > subordinate)
 			pci_warn(dev, "bridge has subordinate %02x but max busn %02x\n",
 				 subordinate, cmax);
@@ -1574,23 +1659,33 @@
 
 static void set_pcie_untrusted(struct pci_dev *dev)
 {
-	struct pci_dev *parent;
+	struct pci_dev *parent = pci_upstream_bridge(dev);
 
+	if (!parent)
+		return;
 	/*
-	 * If the upstream bridge is untrusted we treat this device
+	 * If the upstream bridge is untrusted we treat this device as
 	 * untrusted as well.
 	 */
-	parent = pci_upstream_bridge(dev);
-	if (parent && (parent->untrusted || parent->external_facing))
+	if (parent->untrusted) {
 		dev->untrusted = true;
+		return;
+	}
+
+	if (arch_pci_dev_is_removable(dev)) {
+		pci_dbg(dev, "marking as untrusted\n");
+		dev->untrusted = true;
+	}
 }
 
 static void pci_set_removable(struct pci_dev *dev)
 {
 	struct pci_dev *parent = pci_upstream_bridge(dev);
 
+	if (!parent)
+		return;
 	/*
-	 * We (only) consider everything downstream from an external_facing
+	 * We (only) consider everything tunneled below an external_facing
 	 * device to be removable by the user. We're mainly concerned with
 	 * consumer platforms with user accessible thunderbolt ports that are
 	 * vulnerable to DMA attacks, and we expect those ports to be marked by
@@ -1600,9 +1695,15 @@
 	 * accessible to user / may not be removed by end user, and thus not
 	 * exposed as "removable" to userspace.
 	 */
-	if (parent &&
-	    (parent->external_facing || dev_is_removable(&parent->dev)))
+	if (dev_is_removable(&parent->dev)) {
 		dev_set_removable(&dev->dev, DEVICE_REMOVABLE);
+		return;
+	}
+
+	if (arch_pci_dev_is_removable(dev)) {
+		pci_dbg(dev, "marking as removable\n");
+		dev_set_removable(&dev->dev, DEVICE_REMOVABLE);
+	}
 }
 
 /**
@@ -1875,6 +1976,9 @@
 
 	dev->broken_intx_masking = pci_intx_mask_broken(dev);
 
+	/* Clear errors left from system firmware */
+	pci_write_config_word(dev, PCI_STATUS, 0xffff);
+
 	switch (dev->hdr_type) {		    /* header type */
 	case PCI_HEADER_TYPE_NORMAL:		    /* standard header */
 		if (class == PCI_CLASS_BRIDGE_PCI)
@@ -2168,9 +2272,21 @@
 	 * Complex and all intermediate Switches indicate support for LTR.
 	 * PCIe r4.0, sec 6.18.
 	 */
-	if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
-	    ((bridge = pci_upstream_bridge(dev)) &&
-	      bridge->ltr_path)) {
+	if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT) {
+		pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
+					 PCI_EXP_DEVCTL2_LTR_EN);
+		dev->ltr_path = 1;
+		return;
+	}
+
+	/*
+	 * If we're configuring a hot-added device, LTR was likely
+	 * disabled in the upstream bridge, so re-enable it before enabling
+	 * it in the new device.
+	 */
+	bridge = pci_upstream_bridge(dev);
+	if (bridge && bridge->ltr_path) {
+		pci_bridge_reconfigure_ltr(dev);
 		pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
 					 PCI_EXP_DEVCTL2_LTR_EN);
 		dev->ltr_path = 1;
@@ -2892,8 +3008,8 @@
 		 * hotplug bridges too much during the second scan below.
 		 */
 		used_buses++;
-		if (cmax - max > 1)
-			used_buses += cmax - max - 1;
+		if (max - cmax > 1)
+			used_buses += max - cmax - 1;
 	}
 
 	/* Scan bridges that need to be reconfigured */
@@ -2901,7 +3017,6 @@
 		unsigned int buses = 0;
 
 		if (!hotplug_bridges && normal_bridges == 1) {
-
 			/*
 			 * There is only one bridge on the bus (upstream
 			 * port) so it gets all available buses which it
@@ -2910,7 +3025,6 @@
 			 */
 			buses = available_buses;
 		} else if (dev->is_hotplug_bridge) {
-
 			/*
 			 * Distribute the extra buses between hotplug
 			 * bridges if any.
@@ -2929,7 +3043,7 @@
 	/*
 	 * Make sure a hotplug bridge has at least the minimum requested
 	 * number of buses but allow it to grow up to the maximum available
-	 * bus number of there is room.
+	 * bus number if there is room.
 	 */
 	if (bus->self && bus->self->is_hotplug_bridge) {
 		used_buses = max_t(unsigned int, available_buses,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/quirks.c
@@ -12,6 +12,7 @@
  * file, where their drivers can use them.
  */
 
+#include <linux/bitfield.h>
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/export.h>
@@ -206,6 +207,21 @@
 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID,
 				PCI_CLASS_BRIDGE_HOST, 8, quirk_mmio_always_on);
 
+/* The BAR0 ~ BAR4 of Marvell 9125 device can't be accessed
+*  by IO resource file, and need to skip the files
+*/
+static void quirk_marvell_mask_bar(struct pci_dev *dev)
+{
+	int i;
+
+	for (i = 0; i < 5; i++)
+		if (dev->resource[i].start)
+			dev->resource[i].start =
+				dev->resource[i].end = 0;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9125,
+				quirk_marvell_mask_bar);
+
 /*
  * The Mellanox Tavor device gives false positive parity errors.  Disable
  * parity error reporting.
@@ -592,7 +608,7 @@
 /*
  * In the AMD NL platform, this device ([1022:7912]) has a class code of
  * PCI_CLASS_SERIAL_USB_XHCI (0x0c0330), which means the xhci driver will
- * claim it.
+ * claim it. The same applies on the VanGogh platform device ([1022:163a]).
  *
  * But the dwc3 driver is a more specific driver for this device, and we'd
  * prefer to use it instead of xhci. To prevent xhci from claiming the
@@ -600,17 +616,22 @@
  * defines as "USB device (not host controller)". The dwc3 driver can then
  * claim it based on its Vendor and Device ID.
  */
-static void quirk_amd_nl_class(struct pci_dev *pdev)
+static void quirk_amd_dwc_class(struct pci_dev *pdev)
 {
 	u32 class = pdev->class;
 
-	/* Use "USB Device (not host controller)" class */
-	pdev->class = PCI_CLASS_SERIAL_USB_DEVICE;
-	pci_info(pdev, "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n",
-		 class, pdev->class);
+	if (class != PCI_CLASS_SERIAL_USB_DEVICE) {
+		/* Use "USB Device (not host controller)" class */
+		pdev->class = PCI_CLASS_SERIAL_USB_DEVICE;
+		pci_info(pdev,
+			"PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n",
+			class, pdev->class);
+	}
 }
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_NL_USB,
-		quirk_amd_nl_class);
+		quirk_amd_dwc_class);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VANGOGH_USB,
+		quirk_amd_dwc_class);
 
 /*
  * Synopsys USB 3.x host HAPS platform has a class code of
@@ -1811,6 +1832,18 @@
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_EESSC,	quirk_alder_ioapic);
 #endif
 
+static void quirk_no_msi(struct pci_dev *dev)
+{
+	pci_info(dev, "avoiding MSI to work around a hardware defect\n");
+	dev->no_msi = 1;
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4386, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4387, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4388, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4389, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438a, quirk_no_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438b, quirk_no_msi);
+
 static void quirk_pcie_mch(struct pci_dev *pdev)
 {
 	pdev->no_msi = 1;
@@ -3464,6 +3497,8 @@
 			quirk_broken_intx_masking);
 DECLARE_PCI_FIXUP_FINAL(0x1b7c, 0x0004, /* Ceton InfiniTV4 */
 			quirk_broken_intx_masking);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CREATIVE, PCI_DEVICE_ID_CREATIVE_20K2,
+			quirk_broken_intx_masking);
 
 /*
  * Realtek RTL8169 PCI Gigabit Ethernet Controller (rev 10)
@@ -3612,6 +3647,7 @@
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003c, quirk_no_bus_reset);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0033, quirk_no_bus_reset);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0034, quirk_no_bus_reset);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003e, quirk_no_bus_reset);
 
 /*
  * Root port on some Cavium CN8xxx chips do not successfully complete a bus
@@ -3652,6 +3688,19 @@
 			       PCI_CLASS_DISPLAY_VGA, 8, quirk_no_pm_reset);
 
 /*
+ * Spectrum-{1,2,3,4} devices report that a D3hot->D0 transition causes a reset
+ * (i.e., they advertise NoSoftRst-). However, this transition does not have
+ * any effect on the device: It continues to be operational and network ports
+ * remain up. Advertising this support makes it seem as if a PM reset is viable
+ * for these devices. Mark it as unavailable to skip it when testing reset
+ * methods.
+ */
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcb84, quirk_no_pm_reset);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcf6c, quirk_no_pm_reset);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcf70, quirk_no_pm_reset);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcf80, quirk_no_pm_reset);
+
+/*
  * Thunderbolt controllers with broken MSI hotplug signaling:
  * Entire 1st generation (Light Ridge, Eagle Ridge, Light Peak) and part
  * of the 2nd generation (Cactus Ridge 4C up to revision 1, Port Ridge).
@@ -4086,6 +4135,10 @@
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe832, quirk_dma_func0_alias);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe476, quirk_dma_func0_alias);
 
+/* Some Glenfly chips use function 0 as the PCIe Requester ID for DMA */
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_GLENFLY, 0x3d40, quirk_dma_func0_alias);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_GLENFLY, 0x3d41, quirk_dma_func0_alias);
+
 static void quirk_dma_func1_alias(struct pci_dev *dev)
 {
 	if (PCI_FUNC(dev->devfn) != 1)
@@ -4102,6 +4155,9 @@
 			 quirk_dma_func1_alias);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9123,
 			 quirk_dma_func1_alias);
+/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c136 */
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9125,
+			 quirk_dma_func1_alias);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9128,
 			 quirk_dma_func1_alias);
 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c14 */
@@ -4133,6 +4189,8 @@
 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c49 */
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9230,
 			 quirk_dma_func1_alias);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9235,
+			 quirk_dma_func1_alias);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0642,
 			 quirk_dma_func1_alias);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0645,
@@ -4557,17 +4615,21 @@
  * But the implementation could block peer-to-peer transactions between them
  * and provide ACS-like functionality.
  */
-static int  pci_quirk_zhaoxin_pcie_ports_acs(struct pci_dev *dev, u16 acs_flags)
+static int pci_quirk_zhaoxin_pcie_ports_acs(struct pci_dev *dev, u16 acs_flags)
 {
 	if (!pci_is_pcie(dev) ||
 	    ((pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) &&
 	     (pci_pcie_type(dev) != PCI_EXP_TYPE_DOWNSTREAM)))
 		return -ENOTTY;
 
+	/*
+	 * Future Zhaoxin Root Ports and Switch Downstream Ports will
+	 * implement ACS capability in accordance with the PCIe Spec.
+	 */
 	switch (dev->device) {
 	case 0x0710 ... 0x071e:
 	case 0x0721:
-	case 0x0723 ... 0x0732:
+	case 0x0723 ... 0x0752:
 		return pci_acs_ctrl_enabled(acs_flags,
 			PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF);
 	}
@@ -4807,6 +4869,29 @@
 		PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF);
 }
 
+/*
+ * Wangxun 40G/25G/10G/1G NICs have no ACS capability, but on
+ * multi-function devices, the hardware isolates the functions by
+ * directing all peer-to-peer traffic upstream as though PCI_ACS_RR and
+ * PCI_ACS_CR were set.
+ * SFxxx 1G NICs(em).
+ * RP1000/RP2000 10G NICs(sp).
+ * FF5xxx 40G/25G/10G NICs(aml).
+ */
+static int  pci_quirk_wangxun_nic_acs(struct pci_dev *dev, u16 acs_flags)
+{
+	switch (dev->device) {
+	case 0x0100 ... 0x010F: /* EM */
+	case 0x1001: case 0x2001: /* SP */
+	case 0x5010: case 0x5025: case 0x5040: /* AML */
+	case 0x5110: case 0x5125: case 0x5140: /* AML */
+		return pci_acs_ctrl_enabled(acs_flags,
+			PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF);
+	}
+
+	return false;
+}
+
 static const struct pci_dev_acs_enabled {
 	u16 vendor;
 	u16 device;
@@ -4881,6 +4966,8 @@
 	/* QCOM QDF2xxx root ports */
 	{ PCI_VENDOR_ID_QCOM, 0x0400, pci_quirk_qcom_rp_acs },
 	{ PCI_VENDOR_ID_QCOM, 0x0401, pci_quirk_qcom_rp_acs },
+	/* QCOM SA8775P root port */
+	{ PCI_VENDOR_ID_QCOM, 0x0115, pci_quirk_qcom_rp_acs },
 	/* HXT SD4800 root ports. The ACS design is same as QCOM QDF2xxx */
 	{ PCI_VENDOR_ID_HXT, 0x0401, pci_quirk_qcom_rp_acs },
 	/* Intel PCH root ports */
@@ -4907,6 +4994,13 @@
 	{ PCI_VENDOR_ID_AMPERE, 0xE00C, pci_quirk_xgene_acs },
 	/* Broadcom multi-function device */
 	{ PCI_VENDOR_ID_BROADCOM, 0x16D7, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1750, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1751, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1752, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1760, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1761, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1762, pci_quirk_mf_endpoint_acs },
+	{ PCI_VENDOR_ID_BROADCOM, 0x1763, pci_quirk_mf_endpoint_acs },
 	{ PCI_VENDOR_ID_BROADCOM, 0xD714, pci_quirk_brcm_acs },
 	/* Amazon Annapurna Labs */
 	{ PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031, pci_quirk_al_acs },
@@ -4949,6 +5043,8 @@
 	{ PCI_VENDOR_ID_NXP, 0x8d9b, pci_quirk_nxp_rp_acs },
 	/* Zhaoxin Root/Downstream Ports */
 	{ PCI_VENDOR_ID_ZHAOXIN, PCI_ANY_ID, pci_quirk_zhaoxin_pcie_ports_acs },
+	/* Wangxun nics */
+	{ PCI_VENDOR_ID_WANGXUN, PCI_ANY_ID, pci_quirk_wangxun_nic_acs },
 	{ 0 }
 };
 
@@ -5309,6 +5405,7 @@
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x1487, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x148c, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x149c, quirk_no_flr);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x7901, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1502, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1503, quirk_no_flr);
 
@@ -5324,6 +5421,7 @@
 
 	pci_walk_bus(bridge->bus, pci_configure_extended_tags, NULL);
 }
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_3WARE, 0x1004, quirk_no_ext_tags);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0132, quirk_no_ext_tags);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0140, quirk_no_ext_tags);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0141, quirk_no_ext_tags);
@@ -5333,6 +5431,12 @@
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0422, quirk_no_ext_tags);
 
 #ifdef CONFIG_PCI_ATS
+static void quirk_no_ats(struct pci_dev *pdev)
+{
+	pci_info(pdev, "disabling ATS\n");
+	pdev->ats_cap = 0;
+}
+
 /*
  * Some devices require additional driver setup to enable ATS.  Don't use
  * ATS for those devices as ATS will be enabled before the driver has had a
@@ -5340,25 +5444,16 @@
  */
 static void quirk_amd_harvest_no_ats(struct pci_dev *pdev)
 {
-	if ((pdev->device == 0x7312 && pdev->revision != 0x00) ||
-	    (pdev->device == 0x7340 && pdev->revision != 0xc5) ||
-	    (pdev->device == 0x7341 && pdev->revision != 0x00))
-		return;
-
 	if (pdev->device == 0x15d8) {
 		if (pdev->revision == 0xcf &&
 		    pdev->subsystem_vendor == 0xea50 &&
 		    (pdev->subsystem_device == 0xce19 ||
 		     pdev->subsystem_device == 0xcc10 ||
 		     pdev->subsystem_device == 0xcc08))
-			goto no_ats;
-		else
-			return;
+			quirk_no_ats(pdev);
+	} else {
+		quirk_no_ats(pdev);
 	}
-
-no_ats:
-	pci_info(pdev, "disabling ATS\n");
-	pdev->ats_cap = 0;
 }
 
 /* AMD Stoney platform GPU */
@@ -5366,12 +5461,40 @@
 /* AMD Iceland dGPU */
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x6900, quirk_amd_harvest_no_ats);
 /* AMD Navi10 dGPU */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7310, quirk_amd_harvest_no_ats);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7312, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7318, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7319, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731a, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731b, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731e, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731f, quirk_amd_harvest_no_ats);
 /* AMD Navi14 dGPU */
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7340, quirk_amd_harvest_no_ats);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7341, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7347, quirk_amd_harvest_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x734f, quirk_amd_harvest_no_ats);
 /* AMD Raven platform iGPU */
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x15d8, quirk_amd_harvest_no_ats);
+
+/*
+ * Intel IPU E2000 revisions before C0 implement incorrect endianness
+ * in ATS Invalidate Request message body. Disable ATS for those devices.
+ */
+static void quirk_intel_e2000_no_ats(struct pci_dev *pdev)
+{
+	if (pdev->revision < 0x20)
+		quirk_no_ats(pdev);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1451, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1452, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1453, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1454, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1455, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1457, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1459, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x145a, quirk_intel_e2000_no_ats);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x145c, quirk_intel_e2000_no_ats);
 #endif /* CONFIG_PCI_ATS */
 
 /* Freescale PCIe doesn't support MSI in RC mode */
@@ -5795,3 +5918,209 @@
 }
 DECLARE_PCI_FIXUP_CLASS_HEADER(0x1ac1, 0x089a,
 			       PCI_CLASS_NOT_DEFINED, 8, apex_pci_fixup_class);
+
+/*
+ * BIOS may not be able to access config space of devices under VMD domain, so
+ * it relies on software to enable ASPM for links under VMD.
+ */
+static bool pci_fixup_is_vmd_bridge(struct pci_dev *pdev)
+{
+	struct pci_bus *bus = pdev->bus;
+	struct device *dev;
+	struct pci_driver *pdrv;
+
+	if (!pci_is_root_bus(bus))
+		return false;
+
+	dev = bus->bridge->parent;
+	if (dev == NULL)
+		return false;
+
+	pdrv = pci_dev_driver(to_pci_dev(dev));
+	if (pdrv == NULL || strcmp("vmd", pdrv->name))
+		return false;
+
+	return true;
+}
+
+static void pci_fixup_enable_aspm(struct pci_dev *pdev)
+{
+	if (!pci_fixup_is_vmd_bridge(pdev))
+		return;
+
+	pdev->dev_flags |= PCI_DEV_FLAGS_ENABLE_ASPM;
+	pci_info(pdev, "enable ASPM for pci bridge behind vmd");
+}
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
+			       PCI_CLASS_BRIDGE_PCI, 8, pci_fixup_enable_aspm);
+
+static void pci_fixup_enable_vmd_nvme_ltr(struct pci_dev *pdev)
+{
+	struct pci_dev *parent;
+	int pos;
+	u16 val;
+
+	parent = pci_upstream_bridge(pdev);
+	if (!parent)
+		return;
+
+	if (!pci_fixup_is_vmd_bridge(parent))
+		return;
+
+	pos = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_LTR);
+	if (!pos)
+		return;
+
+	pci_read_config_word(pdev, pos + PCI_LTR_MAX_SNOOP_LAT, &val);
+	if (val)
+		return;
+
+	pci_read_config_word(pdev, pos + PCI_LTR_MAX_NOSNOOP_LAT, &val);
+	if (val)
+		return;
+
+	/* 3145728ns, i.e. 0x300000ns */
+	pci_write_config_word(pdev, pos + PCI_LTR_MAX_SNOOP_LAT, 0x1003);
+	pci_write_config_word(pdev, pos + PCI_LTR_MAX_NOSNOOP_LAT, 0x1003);
+	pci_info(pdev, "enable LTR for nvme behind vmd");
+}
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID,
+			      PCI_CLASS_STORAGE_EXPRESS, 0, pci_fixup_enable_vmd_nvme_ltr);
+
+static void pci_fixup_serialize_tgl_me_pm(struct pci_dev *pdev)
+{
+	struct pci_dev *rciep = NULL;
+
+	if (!pdev->bus)
+		return;
+
+	for_each_pci_dev(rciep) {
+		/* Most of TGL RCiEPs don't have type PCI_EXP_TYPE_RC_END,
+		 * check parent bridge instead. */
+		if (!rciep->bus)
+			continue;
+
+		if (rciep->bus->self != pdev->bus->self)
+			continue;
+
+		if (&rciep->dev == &pdev->dev)
+			continue;
+
+		if (device_link_add(&rciep->dev, &pdev->dev,
+				    DL_FLAG_STATELESS))
+			pci_info(rciep, "Suspend before and resume after %s\n",
+				 pci_name(pdev));
+	}
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x15fb, pci_fixup_serialize_tgl_me_pm);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x15fc, pci_fixup_serialize_tgl_me_pm);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x15f9, pci_fixup_serialize_tgl_me_pm);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x15fa, pci_fixup_serialize_tgl_me_pm);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x15f4, pci_fixup_serialize_tgl_me_pm);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x15f5, pci_fixup_serialize_tgl_me_pm);
+
+static void nvidia_ion_ahci_fixup(struct pci_dev *pdev)
+{
+	pdev->dev_flags |= PCI_DEV_FLAGS_HAS_MSI_MASKING;
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, 0x0ab8, nvidia_ion_ahci_fixup);
+
+static void rom_bar_overlap_defect(struct pci_dev *dev)
+{
+	pci_info(dev, "working around ROM BAR overlap defect\n");
+	dev->rom_bar_overlap = 1;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1533, rom_bar_overlap_defect);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1536, rom_bar_overlap_defect);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1537, rom_bar_overlap_defect);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1538, rom_bar_overlap_defect);
+
+#ifdef CONFIG_PCIEASPM
+/*
+ * Several Intel DG2 graphics devices advertise that they can only tolerate
+ * 1us latency when transitioning from L1 to L0, which may prevent ASPM L1
+ * from being enabled.  But in fact these devices can tolerate unlimited
+ * latency.  Override their Device Capabilities value to allow ASPM L1 to
+ * be enabled.
+ */
+static void aspm_l1_acceptable_latency(struct pci_dev *dev)
+{
+	u32 l1_lat = FIELD_GET(PCI_EXP_DEVCAP_L1, dev->devcap);
+
+	if (l1_lat < 7) {
+		dev->devcap |= FIELD_PREP(PCI_EXP_DEVCAP_L1, 7);
+		pci_info(dev, "ASPM: overriding L1 acceptable latency from %#x to 0x7\n",
+			 l1_lat);
+	}
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f80, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f81, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f82, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f83, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f84, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f85, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f86, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f87, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f88, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5690, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5691, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5692, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5693, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5694, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5695, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a0, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a1, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a2, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a3, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a4, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a5, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a6, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b0, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b1, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c0, aspm_l1_acceptable_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c1, aspm_l1_acceptable_latency);
+#endif
+
+#ifdef CONFIG_PCIE_DPC
+/*
+ * Intel Ice Lake, Tiger Lake and Alder Lake BIOS has a bug that clears
+ * the DPC RP PIO Log Size of the integrated Thunderbolt PCIe Root
+ * Ports.
+ */
+static void dpc_log_size(struct pci_dev *dev)
+{
+	u16 dpc, val;
+
+	dpc = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_DPC);
+	if (!dpc)
+		return;
+
+	pci_read_config_word(dev, dpc + PCI_EXP_DPC_CAP, &val);
+	if (!(val & PCI_EXP_DPC_CAP_RP_EXT))
+		return;
+
+	if (!((val & PCI_EXP_DPC_RP_PIO_LOG_SIZE) >> 8)) {
+		pci_info(dev, "Overriding RP PIO Log Size to 4\n");
+		dev->dpc_rp_log_size = 4;
+	}
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x461f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x462f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x463f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x466e, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a1d, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a1f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a21, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a23, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a23, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a25, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a27, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a29, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2b, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2d, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a31, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0xa72f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0xa73f, dpc_log_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0xa76e, dpc_log_size);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/setup-bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/setup-bus.c
@@ -824,11 +824,9 @@
 		size = min_size;
 	if (old_size == 1)
 		old_size = 0;
-	if (size < old_size)
-		size = old_size;
 
-	size = ALIGN(max(size, add_size) + children_add_size, align);
-	return size;
+	size = max(size, add_size) + children_add_size;
+	return ALIGN(max(size, old_size), align);
 }
 
 resource_size_t __weak pcibios_window_alignment(struct pci_bus *bus,
@@ -994,7 +992,7 @@
 {
 	struct pci_dev *dev;
 	resource_size_t min_align, align, size, size0, size1;
-	resource_size_t aligns[18]; /* Alignments from 1MB to 128GB */
+	resource_size_t aligns[24]; /* Alignments from 1MB to 8TB */
 	int order, max_order;
 	struct resource *b_res = find_bus_resource_of_type(bus,
 					mask | IORESOURCE_PREFETCH, type);
@@ -1745,119 +1743,6 @@
 }
 #endif
 
-/*
- * First try will not touch PCI bridge res.
- * Second and later try will clear small leaf bridge res.
- * Will stop till to the max depth if can not find good one.
- */
-void pci_assign_unassigned_root_bus_resources(struct pci_bus *bus)
-{
-	LIST_HEAD(realloc_head);
-	/* List of resources that want additional resources */
-	struct list_head *add_list = NULL;
-	int tried_times = 0;
-	enum release_type rel_type = leaf_only;
-	LIST_HEAD(fail_head);
-	struct pci_dev_resource *fail_res;
-	int pci_try_num = 1;
-	enum enable_type enable_local;
-
-	/* Don't realloc if asked to do so */
-	enable_local = pci_realloc_detect(bus, pci_realloc_enable);
-	if (pci_realloc_enabled(enable_local)) {
-		int max_depth = pci_bus_get_depth(bus);
-
-		pci_try_num = max_depth + 1;
-		dev_info(&bus->dev, "max bus depth: %d pci_try_num: %d\n",
-			 max_depth, pci_try_num);
-	}
-
-again:
-	/*
-	 * Last try will use add_list, otherwise will try good to have as must
-	 * have, so can realloc parent bridge resource
-	 */
-	if (tried_times + 1 == pci_try_num)
-		add_list = &realloc_head;
-	/*
-	 * Depth first, calculate sizes and alignments of all subordinate buses.
-	 */
-	__pci_bus_size_bridges(bus, add_list);
-
-	/* Depth last, allocate resources and update the hardware. */
-	__pci_bus_assign_resources(bus, add_list, &fail_head);
-	if (add_list)
-		BUG_ON(!list_empty(add_list));
-	tried_times++;
-
-	/* Any device complain? */
-	if (list_empty(&fail_head))
-		goto dump;
-
-	if (tried_times >= pci_try_num) {
-		if (enable_local == undefined)
-			dev_info(&bus->dev, "Some PCI device resources are unassigned, try booting with pci=realloc\n");
-		else if (enable_local == auto_enabled)
-			dev_info(&bus->dev, "Automatically enabled pci realloc, if you have problem, try booting with pci=realloc=off\n");
-
-		free_list(&fail_head);
-		goto dump;
-	}
-
-	dev_info(&bus->dev, "No. %d try to assign unassigned res\n",
-		 tried_times + 1);
-
-	/* Third times and later will not check if it is leaf */
-	if ((tried_times + 1) > 2)
-		rel_type = whole_subtree;
-
-	/*
-	 * Try to release leaf bridge's resources that doesn't fit resource of
-	 * child device under that bridge.
-	 */
-	list_for_each_entry(fail_res, &fail_head, list)
-		pci_bus_release_bridge_resources(fail_res->dev->bus,
-						 fail_res->flags & PCI_RES_TYPE_MASK,
-						 rel_type);
-
-	/* Restore size and flags */
-	list_for_each_entry(fail_res, &fail_head, list) {
-		struct resource *res = fail_res->res;
-		int idx;
-
-		res->start = fail_res->start;
-		res->end = fail_res->end;
-		res->flags = fail_res->flags;
-
-		if (pci_is_bridge(fail_res->dev)) {
-			idx = res - &fail_res->dev->resource[0];
-			if (idx >= PCI_BRIDGE_RESOURCES &&
-			    idx <= PCI_BRIDGE_RESOURCE_END)
-				res->flags = 0;
-		}
-	}
-	free_list(&fail_head);
-
-	goto again;
-
-dump:
-	/* Dump the resource on buses */
-	pci_bus_dump_resources(bus);
-}
-
-void __init pci_assign_unassigned_resources(void)
-{
-	struct pci_bus *root_bus;
-
-	list_for_each_entry(root_bus, &pci_root_buses, node) {
-		pci_assign_unassigned_root_bus_resources(root_bus);
-
-		/* Make sure the root bridge has a companion ACPI device */
-		if (ACPI_HANDLE(root_bus->bridge))
-			acpi_ioapic_add(ACPI_HANDLE(root_bus->bridge));
-	}
-}
-
 static void adjust_bridge_window(struct pci_dev *bridge, struct resource *res,
 				 struct list_head *add_list,
 				 resource_size_t new_size)
@@ -1878,12 +1763,70 @@
 		add_size = size - new_size;
 		pci_dbg(bridge, "bridge window %pR shrunken by %pa\n", res,
 			&add_size);
+	} else {
+		return;
 	}
 
 	res->end = res->start + new_size - 1;
-	remove_from_list(add_list, res);
+
+	/* If the resource is part of the add_list remove it now */
+	if (add_list)
+		remove_from_list(add_list, res);
 }
 
+static void remove_dev_resource(struct resource *avail, struct pci_dev *dev,
+				struct resource *res)
+{
+	resource_size_t size, align, tmp;
+
+	size = resource_size(res);
+	if (!size)
+		return;
+
+	align = pci_resource_alignment(dev, res);
+	align = align ? ALIGN(avail->start, align) - avail->start : 0;
+	tmp = align + size;
+	avail->start = min(avail->start + tmp, avail->end + 1);
+}
+
+static void remove_dev_resources(struct pci_dev *dev, struct resource *io,
+				 struct resource *mmio,
+				 struct resource *mmio_pref)
+{
+	int i;
+
+	for (i = 0; i < PCI_NUM_RESOURCES; i++) {
+		struct resource *res = &dev->resource[i];
+
+		if (resource_type(res) == IORESOURCE_IO) {
+			remove_dev_resource(io, dev, res);
+		} else if (resource_type(res) == IORESOURCE_MEM) {
+
+			/*
+			 * Make sure prefetchable memory is reduced from
+			 * the correct resource. Specifically we put 32-bit
+			 * prefetchable memory in non-prefetchable window
+			 * if there is an 64-bit pretchable window.
+			 *
+			 * See comments in __pci_bus_size_bridges() for
+			 * more information.
+			 */
+			if ((res->flags & IORESOURCE_PREFETCH) &&
+			    ((res->flags & IORESOURCE_MEM_64) ==
+			     (mmio_pref->flags & IORESOURCE_MEM_64)))
+				remove_dev_resource(mmio_pref, dev, res);
+			else
+				remove_dev_resource(mmio, dev, res);
+		}
+	}
+}
+
+/*
+ * io, mmio and mmio_pref contain the total amount of bridge window space
+ * available. This includes the minimal space needed to cover all the
+ * existing devices on the bus and the possible extra space that can be
+ * shared with the bridges.
+ */
 static void pci_bus_distribute_available_resources(struct pci_bus *bus,
 					    struct list_head *add_list,
 					    struct resource io,
@@ -1893,7 +1836,7 @@
 	unsigned int normal_bridges = 0, hotplug_bridges = 0;
 	struct resource *io_res, *mmio_res, *mmio_pref_res;
 	struct pci_dev *dev, *bridge = bus->self;
-	resource_size_t io_per_hp, mmio_per_hp, mmio_pref_per_hp, align;
+	resource_size_t io_per_b, mmio_per_b, mmio_pref_per_b, align;
 
 	io_res = &bridge->resource[PCI_BRIDGE_IO_WINDOW];
 	mmio_res = &bridge->resource[PCI_BRIDGE_MEM_WINDOW];
@@ -1937,105 +1880,101 @@
 			normal_bridges++;
 	}
 
+	if (!(hotplug_bridges + normal_bridges))
+		return;
+
 	/*
-	 * There is only one bridge on the bus so it gets all available
-	 * resources which it can then distribute to the possible hotplug
-	 * bridges below.
+	 * Calculate the amount of space we can forward from "bus" to any
+	 * downstream buses, i.e., the space left over after assigning the
+	 * BARs and windows on "bus".
 	 */
-	if (hotplug_bridges + normal_bridges == 1) {
-		dev = list_first_entry(&bus->devices, struct pci_dev, bus_list);
-		if (dev->subordinate)
-			pci_bus_distribute_available_resources(dev->subordinate,
-				add_list, io, mmio, mmio_pref);
-		return;
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		if (!dev->is_virtfn)
+			remove_dev_resources(dev, &io, &mmio, &mmio_pref);
 	}
 
-	if (hotplug_bridges == 0)
-		return;
-
 	/*
-	 * Calculate the total amount of extra resource space we can
-	 * pass to bridges below this one.  This is basically the
-	 * extra space reduced by the minimal required space for the
-	 * non-hotplug bridges.
+	 * If there is at least one hotplug bridge on this bus it gets all
+	 * the extra resource space that was left after the reductions
+	 * above.
+	 *
+	 * If there are no hotplug bridges the extra resource space is
+	 * split between non-hotplug bridges. This is to allow possible
+	 * hotplug bridges below them to get the extra space as well.
 	 */
+	if (hotplug_bridges) {
+		io_per_b = div64_ul(resource_size(&io), hotplug_bridges);
+		mmio_per_b = div64_ul(resource_size(&mmio), hotplug_bridges);
+		mmio_pref_per_b = div64_ul(resource_size(&mmio_pref),
+					   hotplug_bridges);
+	} else {
+		io_per_b = div64_ul(resource_size(&io), normal_bridges);
+		mmio_per_b = div64_ul(resource_size(&mmio), normal_bridges);
+		mmio_pref_per_b = div64_ul(resource_size(&mmio_pref),
+					   normal_bridges);
+	}
+
 	for_each_pci_bridge(dev, bus) {
-		resource_size_t used_size;
 		struct resource *res;
+		struct pci_bus *b;
 
-		if (dev->is_hotplug_bridge)
+		b = dev->subordinate;
+		if (!b)
+			continue;
+		if (hotplug_bridges && !dev->is_hotplug_bridge)
 			continue;
 
+		res = &dev->resource[PCI_BRIDGE_IO_WINDOW];
+
 		/*
-		 * Reduce the available resource space by what the
-		 * bridge and devices below it occupy.
+		 * Make sure the split resource space is properly aligned
+		 * for bridge windows (align it down to avoid going above
+		 * what is available).
 		 */
-		res = &dev->resource[PCI_BRIDGE_IO_WINDOW];
 		align = pci_resource_alignment(dev, res);
-		align = align ? ALIGN(io.start, align) - io.start : 0;
-		used_size = align + resource_size(res);
-		if (!res->parent)
-			io.start = min(io.start + used_size, io.end + 1);
+		io.end = align ? io.start + ALIGN_DOWN(io_per_b, align) - 1
+			       : io.start + io_per_b - 1;
+
+		/*
+		 * The x_per_b holds the extra resource space that can be
+		 * added for each bridge but there is the minimal already
+		 * reserved as well so adjust x.start down accordingly to
+		 * cover the whole space.
+		 */
+		io.start -= resource_size(res);
 
 		res = &dev->resource[PCI_BRIDGE_MEM_WINDOW];
 		align = pci_resource_alignment(dev, res);
-		align = align ? ALIGN(mmio.start, align) - mmio.start : 0;
-		used_size = align + resource_size(res);
-		if (!res->parent)
-			mmio.start = min(mmio.start + used_size, mmio.end + 1);
+		mmio.end = align ? mmio.start + ALIGN_DOWN(mmio_per_b, align) - 1
+				 : mmio.start + mmio_per_b - 1;
+		mmio.start -= resource_size(res);
 
 		res = &dev->resource[PCI_BRIDGE_PREF_MEM_WINDOW];
 		align = pci_resource_alignment(dev, res);
-		align = align ? ALIGN(mmio_pref.start, align) -
-			mmio_pref.start : 0;
-		used_size = align + resource_size(res);
-		if (!res->parent)
-			mmio_pref.start = min(mmio_pref.start + used_size,
-				mmio_pref.end + 1);
-	}
-
-	io_per_hp = div64_ul(resource_size(&io), hotplug_bridges);
-	mmio_per_hp = div64_ul(resource_size(&mmio), hotplug_bridges);
-	mmio_pref_per_hp = div64_ul(resource_size(&mmio_pref),
-		hotplug_bridges);
-
-	/*
-	 * Go over devices on this bus and distribute the remaining
-	 * resource space between hotplug bridges.
-	 */
-	for_each_pci_bridge(dev, bus) {
-		struct pci_bus *b;
-
-		b = dev->subordinate;
-		if (!b || !dev->is_hotplug_bridge)
-			continue;
-
-		/*
-		 * Distribute available extra resources equally between
-		 * hotplug-capable downstream ports taking alignment into
-		 * account.
-		 */
-		io.end = io.start + io_per_hp - 1;
-		mmio.end = mmio.start + mmio_per_hp - 1;
-		mmio_pref.end = mmio_pref.start + mmio_pref_per_hp - 1;
+		mmio_pref.end = align ? mmio_pref.start +
+					ALIGN_DOWN(mmio_pref_per_b, align) - 1
+				      : mmio_pref.start + mmio_pref_per_b - 1;
+		mmio_pref.start -= resource_size(res);
 
 		pci_bus_distribute_available_resources(b, add_list, io, mmio,
 						       mmio_pref);
 
-		io.start += io_per_hp;
-		mmio.start += mmio_per_hp;
-		mmio_pref.start += mmio_pref_per_hp;
+		io.start += io.end + 1;
+		mmio.start += mmio.end + 1;
+		mmio_pref.start += mmio_pref.end + 1;
 	}
 }
 
 static void pci_bridge_distribute_available_resources(struct pci_dev *bridge,
-						     struct list_head *add_list)
+						      struct list_head *add_list)
 {
 	struct resource available_io, available_mmio, available_mmio_pref;
 
 	if (!bridge->is_hotplug_bridge)
 		return;
 
+	pci_dbg(bridge, "distributing available resources\n");
+
 	/* Take the initial extra resources from the hotplug port */
 	available_io = bridge->resource[PCI_BRIDGE_IO_WINDOW];
 	available_mmio = bridge->resource[PCI_BRIDGE_MEM_WINDOW];
@@ -2047,6 +1986,174 @@
 					       available_mmio_pref);
 }
 
+static bool pci_bridge_resources_not_assigned(struct pci_dev *dev)
+{
+	const struct resource *r;
+
+	/*
+	 * Check the child device's resources and if they are not yet
+	 * assigned it means we are configuring them (not the boot
+	 * firmware) so we should be able to extend the upstream
+	 * bridge's (that's the hotplug downstream PCIe port) resources
+	 * in the same way we do with the normal hotplug case.
+	 */
+	r = &dev->resource[PCI_BRIDGE_IO_WINDOW];
+	if (!r->flags || !(r->flags & IORESOURCE_STARTALIGN))
+		return false;
+	r = &dev->resource[PCI_BRIDGE_MEM_WINDOW];
+	if (!r->flags || !(r->flags & IORESOURCE_STARTALIGN))
+		return false;
+	r = &dev->resource[PCI_BRIDGE_PREF_MEM_WINDOW];
+	if (!r->flags || !(r->flags & IORESOURCE_STARTALIGN))
+		return false;
+
+	return true;
+}
+
+static void pci_root_bus_distribute_available_resources(struct pci_bus *bus,
+							struct list_head *add_list)
+{
+	struct pci_dev *dev, *bridge = bus->self;
+
+	for_each_pci_bridge(dev, bus) {
+		struct pci_bus *b;
+
+		b = dev->subordinate;
+		if (!b)
+			continue;
+
+		/*
+		 * Need to check "bridge" here too because it is NULL
+		 * in case of root bus.
+		 */
+		if (bridge && pci_bridge_resources_not_assigned(dev)) {
+			pci_bridge_distribute_available_resources(bridge, add_list);
+			/*
+			 * There is only PCIe upstream port on the bus
+			 * so we don't need to go futher.
+			 */
+			return;
+		}
+
+		pci_root_bus_distribute_available_resources(b, add_list);
+	}
+}
+
+/*
+ * First try will not touch PCI bridge res.
+ * Second and later try will clear small leaf bridge res.
+ * Will stop till to the max depth if can not find good one.
+ */
+void pci_assign_unassigned_root_bus_resources(struct pci_bus *bus)
+{
+	LIST_HEAD(realloc_head);
+	/* List of resources that want additional resources */
+	struct list_head *add_list = NULL;
+	int tried_times = 0;
+	enum release_type rel_type = leaf_only;
+	LIST_HEAD(fail_head);
+	struct pci_dev_resource *fail_res;
+	int pci_try_num = 1;
+	enum enable_type enable_local;
+
+	/* Don't realloc if asked to do so */
+	enable_local = pci_realloc_detect(bus, pci_realloc_enable);
+	if (pci_realloc_enabled(enable_local)) {
+		int max_depth = pci_bus_get_depth(bus);
+
+		pci_try_num = max_depth + 1;
+		dev_info(&bus->dev, "max bus depth: %d pci_try_num: %d\n",
+			 max_depth, pci_try_num);
+	}
+
+again:
+	/*
+	 * Last try will use add_list, otherwise will try good to have as must
+	 * have, so can realloc parent bridge resource
+	 */
+	if (tried_times + 1 == pci_try_num)
+		add_list = &realloc_head;
+	/*
+	 * Depth first, calculate sizes and alignments of all subordinate buses.
+	 */
+	__pci_bus_size_bridges(bus, add_list);
+
+	pci_root_bus_distribute_available_resources(bus, add_list);
+
+	/* Depth last, allocate resources and update the hardware. */
+	__pci_bus_assign_resources(bus, add_list, &fail_head);
+	if (add_list)
+		BUG_ON(!list_empty(add_list));
+	tried_times++;
+
+	/* Any device complain? */
+	if (list_empty(&fail_head))
+		goto dump;
+
+	if (tried_times >= pci_try_num) {
+		if (enable_local == undefined)
+			dev_info(&bus->dev, "Some PCI device resources are unassigned, try booting with pci=realloc\n");
+		else if (enable_local == auto_enabled)
+			dev_info(&bus->dev, "Automatically enabled pci realloc, if you have problem, try booting with pci=realloc=off\n");
+
+		free_list(&fail_head);
+		goto dump;
+	}
+
+	dev_info(&bus->dev, "No. %d try to assign unassigned res\n",
+		 tried_times + 1);
+
+	/* Third times and later will not check if it is leaf */
+	if ((tried_times + 1) > 2)
+		rel_type = whole_subtree;
+
+	/*
+	 * Try to release leaf bridge's resources that doesn't fit resource of
+	 * child device under that bridge.
+	 */
+	list_for_each_entry(fail_res, &fail_head, list)
+		pci_bus_release_bridge_resources(fail_res->dev->bus,
+						 fail_res->flags & PCI_RES_TYPE_MASK,
+						 rel_type);
+
+	/* Restore size and flags */
+	list_for_each_entry(fail_res, &fail_head, list) {
+		struct resource *res = fail_res->res;
+		int idx;
+
+		res->start = fail_res->start;
+		res->end = fail_res->end;
+		res->flags = fail_res->flags;
+
+		if (pci_is_bridge(fail_res->dev)) {
+			idx = res - &fail_res->dev->resource[0];
+			if (idx >= PCI_BRIDGE_RESOURCES &&
+			    idx <= PCI_BRIDGE_RESOURCE_END)
+				res->flags = 0;
+		}
+	}
+	free_list(&fail_head);
+
+	goto again;
+
+dump:
+	/* Dump the resource on buses */
+	pci_bus_dump_resources(bus);
+}
+
+void __init pci_assign_unassigned_resources(void)
+{
+	struct pci_bus *root_bus;
+
+	list_for_each_entry(root_bus, &pci_root_buses, node) {
+		pci_assign_unassigned_root_bus_resources(root_bus);
+
+		/* Make sure the root bridge has a companion ACPI device */
+		if (ACPI_HANDLE(root_bus->bridge))
+			acpi_ioapic_add(ACPI_HANDLE(root_bus->bridge));
+	}
+}
+
 void pci_assign_unassigned_bridge_resources(struct pci_dev *bridge)
 {
 	struct pci_bus *parent = bridge->subordinate;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/setup-res.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/setup-res.c
@@ -75,12 +75,16 @@
 		 * as zero when disabled, so don't update ROM BARs unless
 		 * they're enabled.  See
 		 * https://lore.kernel.org/r/43147B3D.1030309@vc.cvut.cz/
+		 * But we must update ROM BAR for buggy devices where even a
+		 * disabled ROM can conflict with other BARs.
 		 */
-		if (!(res->flags & IORESOURCE_ROM_ENABLE))
+		if (!(res->flags & IORESOURCE_ROM_ENABLE) &&
+		    !dev->rom_bar_overlap)
 			return;
 
 		reg = dev->rom_base_reg;
-		new |= PCI_ROM_ADDRESS_ENABLE;
+		if (res->flags & IORESOURCE_ROM_ENABLE)
+			new |= PCI_ROM_ADDRESS_ENABLE;
 	} else
 		return;
 
@@ -210,6 +214,17 @@
 
 	root = pci_find_parent_resource(dev, res);
 	if (!root) {
+		/*
+		 * If dev is behind a bridge, accesses will only reach it
+		 * if res is inside the relevant bridge window.
+		 */
+		if (pci_upstream_bridge(dev))
+			return -ENXIO;
+
+		/*
+		 * On the root bus, assume the host bridge will forward
+		 * everything.
+		 */
 		if (res->flags & IORESOURCE_IO)
 			root = &ioport_resource;
 		else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/slot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/slot.c
@@ -79,6 +79,7 @@
 	up_read(&pci_bus_sem);
 
 	list_del(&slot->list);
+	pci_bus_put(slot->bus);
 
 	kfree(slot);
 }
@@ -260,7 +261,7 @@
 		goto err;
 	}
 
-	slot->bus = parent;
+	slot->bus = pci_bus_get(parent);
 	slot->number = slot_nr;
 
 	slot->kobj.kset = pci_slots_kset;
@@ -268,6 +269,7 @@
 	slot_name = make_slot_name(name);
 	if (!slot_name) {
 		err = -ENOMEM;
+		pci_bus_put(slot->bus);
 		kfree(slot);
 		goto err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pci/switch/switchtec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pci/switch/switchtec.c
@@ -552,21 +552,20 @@
 	rc = copy_to_user(data, &stuser->return_code,
 			  sizeof(stuser->return_code));
 	if (rc) {
-		rc = -EFAULT;
-		goto out;
+		mutex_unlock(&stdev->mrpc_mutex);
+		return -EFAULT;
 	}
 
 	data += sizeof(stuser->return_code);
 	rc = copy_to_user(data, &stuser->data,
 			  size - sizeof(stuser->return_code));
 	if (rc) {
-		rc = -EFAULT;
-		goto out;
+		mutex_unlock(&stdev->mrpc_mutex);
+		return -EFAULT;
 	}
 
 	stuser_set_state(stuser, MRPC_IDLE);
 
-out:
 	mutex_unlock(&stdev->mrpc_mutex);
 
 	if (stuser->status == SWITCHTEC_MRPC_STATUS_DONE)
@@ -1251,13 +1250,6 @@
 {
 	struct switchtec_dev *stdev = to_stdev(dev);
 
-	if (stdev->dma_mrpc) {
-		iowrite32(0, &stdev->mmio_mrpc->dma_en);
-		flush_wc_buf(stdev);
-		writeq(0, &stdev->mmio_mrpc->dma_addr);
-		dma_free_coherent(&stdev->pdev->dev, sizeof(*stdev->dma_mrpc),
-				stdev->dma_mrpc, stdev->dma_mrpc_dma_addr);
-	}
 	kfree(stdev);
 }
 
@@ -1301,7 +1293,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	stdev->alive = true;
-	stdev->pdev = pdev;
+	stdev->pdev = pci_dev_get(pdev);
 	INIT_LIST_HEAD(&stdev->mrpc_queue);
 	mutex_init(&stdev->mrpc_mutex);
 	stdev->mrpc_busy = 0;
@@ -1335,6 +1327,7 @@
 	return stdev;
 
 err_put:
+	pci_dev_put(stdev->pdev);
 	put_device(&stdev->dev);
 	return ERR_PTR(rc);
 }
@@ -1587,6 +1580,18 @@
 	return 0;
 }
 
+static void switchtec_exit_pci(struct switchtec_dev *stdev)
+{
+	if (stdev->dma_mrpc) {
+		iowrite32(0, &stdev->mmio_mrpc->dma_en);
+		flush_wc_buf(stdev);
+		writeq(0, &stdev->mmio_mrpc->dma_addr);
+		dma_free_coherent(&stdev->pdev->dev, sizeof(*stdev->dma_mrpc),
+				  stdev->dma_mrpc, stdev->dma_mrpc_dma_addr);
+		stdev->dma_mrpc = NULL;
+	}
+}
+
 static int switchtec_pci_probe(struct pci_dev *pdev,
 			       const struct pci_device_id *id)
 {
@@ -1609,7 +1614,7 @@
 	rc = switchtec_init_isr(stdev);
 	if (rc) {
 		dev_err(&stdev->dev, "failed to init isr.\n");
-		goto err_put;
+		goto err_exit_pci;
 	}
 
 	iowrite32(SWITCHTEC_EVENT_CLEAR |
@@ -1630,6 +1635,8 @@
 
 err_devadd:
 	stdev_kill(stdev);
+err_exit_pci:
+	switchtec_exit_pci(stdev);
 err_put:
 	ida_simple_remove(&switchtec_minor_ida, MINOR(stdev->dev.devt));
 	put_device(&stdev->dev);
@@ -1646,6 +1653,9 @@
 	ida_simple_remove(&switchtec_minor_ida, MINOR(stdev->dev.devt));
 	dev_info(&stdev->dev, "unregistered.\n");
 	stdev_kill(stdev);
+	switchtec_exit_pci(stdev);
+	pci_dev_put(stdev->pdev);
+	stdev->pdev = NULL;
 	put_device(&stdev->dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pcmcia/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pcmcia/Kconfig
@@ -151,7 +151,7 @@
 
 config PCMCIA_ALCHEMY_DEVBOARD
 	tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
-	depends on MIPS_ALCHEMY && PCMCIA
+	depends on MIPS_DB1XXX && PCMCIA
 	help
 	  Enable this driver of you want PCMCIA support on your Alchemy
 	  Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200, DB1300
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pcmcia/cs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pcmcia/cs.c
@@ -605,6 +605,7 @@
 		dev_warn(&skt->dev, "PCMCIA: unable to register socket\n");
 		skt->thread = NULL;
 		complete(&skt->thread_done);
+		put_device(&skt->dev);
 		return 0;
 	}
 	ret = pccard_sysfs_add_socket(&skt->dev);
@@ -666,18 +667,16 @@
 		if (events || sysfs_events)
 			continue;
 
+		set_current_state(TASK_INTERRUPTIBLE);
 		if (kthread_should_stop())
 			break;
 
-		set_current_state(TASK_INTERRUPTIBLE);
-
 		schedule();
 
-		/* make sure we are running */
-		__set_current_state(TASK_RUNNING);
-
 		try_to_freeze();
 	}
+	/* make sure we are running before we exit */
+	__set_current_state(TASK_RUNNING);
 
 	/* shut down socket, if a device is still present */
 	if (skt->state & SOCKET_PRESENT) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pcmcia/ds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pcmcia/ds.c
@@ -513,9 +513,6 @@
 	/* by default don't allow DMA */
 	p_dev->dma_mask = 0;
 	p_dev->dev.dma_mask = &p_dev->dma_mask;
-	dev_set_name(&p_dev->dev, "%d.%d", p_dev->socket->sock, p_dev->device_no);
-	if (!dev_name(&p_dev->dev))
-		goto err_free;
 	p_dev->devname = kasprintf(GFP_KERNEL, "pcmcia%s", dev_name(&p_dev->dev));
 	if (!p_dev->devname)
 		goto err_free;
@@ -573,8 +570,15 @@
 
 	pcmcia_device_query(p_dev);
 
-	if (device_register(&p_dev->dev))
-		goto err_unreg;
+	dev_set_name(&p_dev->dev, "%d.%d", p_dev->socket->sock, p_dev->device_no);
+	if (device_register(&p_dev->dev)) {
+		mutex_lock(&s->ops_mutex);
+		list_del(&p_dev->socket_device_list);
+		s->device_count--;
+		mutex_unlock(&s->ops_mutex);
+		put_device(&p_dev->dev);
+		return NULL;
+	}
 
 	return p_dev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pcmcia/rsrc_nonstatic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pcmcia/rsrc_nonstatic.c
@@ -690,6 +690,9 @@
 	unsigned long min = base;
 	int ret;
 
+	if (!res)
+		return NULL;
+
 	data.mask = align - 1;
 	data.offset = base & data.mask;
 	data.map = &s_data->io_db;
@@ -809,6 +812,9 @@
 	unsigned long min, max;
 	int ret, i, j;
 
+	if (!res)
+		return NULL;
+
 	low = low || !(s->features & SS_CAP_PAGE_REGS);
 
 	data.mask = align - 1;
@@ -1047,6 +1053,8 @@
 		q = p->next;
 		kfree(p);
 	}
+
+	kfree(data);
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pcmcia/yenta_socket.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pcmcia/yenta_socket.c
@@ -636,11 +636,11 @@
 		start = PCIBIOS_MIN_CARDBUS_IO;
 		end = ~0U;
 	} else {
-		unsigned long avail = root->end - root->start;
+		unsigned long avail = resource_size(root);
 		int i;
 		size = BRIDGE_MEM_MAX;
-		if (size > avail/8) {
-			size = (avail+1)/8;
+		if (size > (avail - 1) / 8) {
+			size = avail / 8;
 			/* round size down to next power of 2 */
 			i = 0;
 			while ((size /= 2) != 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm-cmn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm-cmn.c
@@ -1177,7 +1177,7 @@
 		u64 delta;
 		int i;
 
-		for (i = 0; i < CMN_DTM_NUM_COUNTERS; i++) {
+		for (i = 0; i < CMN_DT_NUM_COUNTERS; i++) {
 			if (status & (1U << i)) {
 				ret = IRQ_HANDLED;
 				if (WARN_ON(!dtc->counters[i]))
@@ -1254,9 +1254,10 @@
 	if (dtc->irq < 0)
 		return dtc->irq;
 
-	writel_relaxed(0, dtc->base + CMN_DT_PMCR);
+	writel_relaxed(CMN_DT_DTC_CTL_DT_EN, dtc->base + CMN_DT_DTC_CTL);
+	writel_relaxed(CMN_DT_PMCR_PMU_EN | CMN_DT_PMCR_OVFL_INTR_EN, dtc->base + CMN_DT_PMCR);
+	writeq_relaxed(0, dtc->base + CMN_DT_PMCCNTR);
 	writel_relaxed(0x1ff, dtc->base + CMN_DT_PMOVSR_CLR);
-	writel_relaxed(CMN_DT_PMCR_OVFL_INTR_EN, dtc->base + CMN_DT_PMCR);
 
 	/* We do at least know that a DTC's XP must be in that DTC's domain */
 	xp = arm_cmn_node_to_xp(dn);
@@ -1303,7 +1304,7 @@
 			dn->type = CMN_TYPE_RNI;
 	}
 
-	writel_relaxed(CMN_DT_DTC_CTL_DT_EN, cmn->dtc[0].base + CMN_DT_DTC_CTL);
+	arm_cmn_set_state(cmn, CMN_STATE_DISABLED);
 
 	return 0;
 }
@@ -1561,7 +1562,8 @@
 
 	err = perf_pmu_register(&cmn->pmu, name, -1);
 	if (err)
-		cpuhp_state_remove_instance(arm_cmn_hp_state, &cmn->cpuhp_node);
+		cpuhp_state_remove_instance_nocalls(arm_cmn_hp_state, &cmn->cpuhp_node);
+
 	return err;
 }
 
@@ -1572,7 +1574,7 @@
 	writel_relaxed(0, cmn->dtc[0].base + CMN_DT_DTC_CTL);
 
 	perf_pmu_unregister(&cmn->pmu);
-	cpuhp_state_remove_instance(arm_cmn_hp_state, &cmn->cpuhp_node);
+	cpuhp_state_remove_instance_nocalls(arm_cmn_hp_state, &cmn->cpuhp_node);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm_dmc620_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm_dmc620_pmu.c
@@ -725,6 +725,8 @@
 
 static int __init dmc620_pmu_init(void)
 {
+	int ret;
+
 	cpuhp_state_num = cpuhp_setup_state_multi(CPUHP_AP_ONLINE_DYN,
 				      DMC620_DRVNAME,
 				      NULL,
@@ -732,7 +734,11 @@
 	if (cpuhp_state_num < 0)
 		return cpuhp_state_num;
 
-	return platform_driver_register(&dmc620_pmu_driver);
+	ret = platform_driver_register(&dmc620_pmu_driver);
+	if (ret)
+		cpuhp_remove_multi_state(cpuhp_state_num);
+
+	return ret;
 }
 
 static void __exit dmc620_pmu_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm_dsu_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm_dsu_pmu.c
@@ -858,7 +858,11 @@
 	if (ret < 0)
 		return ret;
 	dsu_pmu_cpuhp_state = ret;
-	return platform_driver_register(&dsu_pmu_driver);
+	ret = platform_driver_register(&dsu_pmu_driver);
+	if (ret)
+		cpuhp_remove_multi_state(dsu_pmu_cpuhp_state);
+
+	return ret;
 }
 
 static void __exit dsu_pmu_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm_pmu.c
@@ -398,6 +398,9 @@
 	if (!validate_event(event->pmu, &fake_pmu, leader))
 		return -EINVAL;
 
+	if (event == leader)
+		return 0;
+
 	for_each_sibling_event(sibling, leader) {
 		if (!validate_event(event->pmu, &fake_pmu, sibling))
 			return -EINVAL;
@@ -487,12 +490,7 @@
 		local64_set(&hwc->period_left, hwc->sample_period);
 	}
 
-	if (event->group_leader != event) {
-		if (validate_group(event) != 0)
-			return -EINVAL;
-	}
-
-	return 0;
+	return validate_group(event);
 }
 
 static int armpmu_event_init(struct perf_event *event)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm_pmu_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm_pmu_platform.c
@@ -117,7 +117,7 @@
 
 	if (num_irqs == 1) {
 		int irq = platform_get_irq(pdev, 0);
-		if (irq && irq_is_percpu_devid(irq))
+		if ((irq > 0) && irq_is_percpu_devid(irq))
 			return pmu_parse_percpu_irq(pmu, irq);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm_smmuv3_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm_smmuv3_pmu.c
@@ -96,6 +96,7 @@
 #define SMMU_PMCG_PA_SHIFT              12
 
 #define SMMU_PMCG_EVCNTR_RDONLY         BIT(0)
+#define SMMU_PMCG_HARDEN_DISABLE        BIT(1)
 
 static int cpuhp_state_num;
 
@@ -140,6 +141,20 @@
 	writel(SMMU_PMCG_CR_ENABLE, smmu_pmu->reg_base + SMMU_PMCG_CR);
 }
 
+static int smmu_pmu_apply_event_filter(struct smmu_pmu *smmu_pmu,
+				       struct perf_event *event, int idx);
+
+static inline void smmu_pmu_enable_quirk_hip08_09(struct pmu *pmu)
+{
+	struct smmu_pmu *smmu_pmu = to_smmu_pmu(pmu);
+	unsigned int idx;
+
+	for_each_set_bit(idx, smmu_pmu->used_counters, smmu_pmu->num_counters)
+		smmu_pmu_apply_event_filter(smmu_pmu, smmu_pmu->events[idx], idx);
+
+	smmu_pmu_enable(pmu);
+}
+
 static inline void smmu_pmu_disable(struct pmu *pmu)
 {
 	struct smmu_pmu *smmu_pmu = to_smmu_pmu(pmu);
@@ -148,6 +163,22 @@
 	writel(0, smmu_pmu->reg_base + SMMU_PMCG_IRQ_CTRL);
 }
 
+static inline void smmu_pmu_disable_quirk_hip08_09(struct pmu *pmu)
+{
+	struct smmu_pmu *smmu_pmu = to_smmu_pmu(pmu);
+	unsigned int idx;
+
+	/*
+	 * The global disable of PMU sometimes fail to stop the counting.
+	 * Harden this by writing an invalid event type to each used counter
+	 * to forcibly stop counting.
+	 */
+	for_each_set_bit(idx, smmu_pmu->used_counters, smmu_pmu->num_counters)
+		writel(0xffff, smmu_pmu->reg_base + SMMU_PMCG_EVTYPER(idx));
+
+	smmu_pmu_disable(pmu);
+}
+
 static inline void smmu_pmu_counter_set_value(struct smmu_pmu *smmu_pmu,
 					      u32 idx, u64 value)
 {
@@ -747,7 +778,10 @@
 	switch (model) {
 	case IORT_SMMU_V3_PMCG_HISI_HIP08:
 		/* HiSilicon Erratum 162001800 */
-		smmu_pmu->options |= SMMU_PMCG_EVCNTR_RDONLY;
+		smmu_pmu->options |= SMMU_PMCG_EVCNTR_RDONLY | SMMU_PMCG_HARDEN_DISABLE;
+		break;
+	case IORT_SMMU_V3_PMCG_HISI_HIP09:
+		smmu_pmu->options |= SMMU_PMCG_HARDEN_DISABLE;
 		break;
 	}
 
@@ -836,6 +870,16 @@
 
 	smmu_pmu_get_acpi_options(smmu_pmu);
 
+	/*
+	 * For platforms suffer this quirk, the PMU disable sometimes fails to
+	 * stop the counters. This will leads to inaccurate or error counting.
+	 * Forcibly disable the counters with these quirk handler.
+	 */
+	if (smmu_pmu->options & SMMU_PMCG_HARDEN_DISABLE) {
+		smmu_pmu->pmu.pmu_enable = smmu_pmu_enable_quirk_hip08_09;
+		smmu_pmu->pmu.pmu_disable = smmu_pmu_disable_quirk_hip08_09;
+	}
+
 	/* Pick one CPU to be the preferred one to use */
 	smmu_pmu->on_cpu = raw_smp_processor_id();
 	WARN_ON(irq_set_affinity(smmu_pmu->irq, cpumask_of(smmu_pmu->on_cpu)));
@@ -896,6 +940,8 @@
 
 static int __init arm_smmu_pmu_init(void)
 {
+	int ret;
+
 	cpuhp_state_num = cpuhp_setup_state_multi(CPUHP_AP_ONLINE_DYN,
 						  "perf/arm/pmcg:online",
 						  NULL,
@@ -903,7 +949,11 @@
 	if (cpuhp_state_num < 0)
 		return cpuhp_state_num;
 
-	return platform_driver_register(&smmu_pmu_driver);
+	ret = platform_driver_register(&smmu_pmu_driver);
+	if (ret)
+		cpuhp_remove_multi_state(cpuhp_state_num);
+
+	return ret;
 }
 module_init(arm_smmu_pmu_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/arm_spe_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/arm_spe_pmu.c
@@ -39,6 +39,24 @@
 #include <asm/mmu.h>
 #include <asm/sysreg.h>
 
+/*
+ * Cache if the event is allowed to trace Context information.
+ * This allows us to perform the check, i.e, perfmon_capable(),
+ * in the context of the event owner, once, during the event_init().
+ */
+#define SPE_PMU_HW_FLAGS_CX			BIT(0)
+
+static void set_spe_event_has_cx(struct perf_event *event)
+{
+	if (IS_ENABLED(CONFIG_PID_IN_CONTEXTIDR) && perfmon_capable())
+		event->hw.flags |= SPE_PMU_HW_FLAGS_CX;
+}
+
+static bool get_spe_event_has_cx(struct perf_event *event)
+{
+	return !!(event->hw.flags & SPE_PMU_HW_FLAGS_CX);
+}
+
 #define ARM_SPE_BUF_PAD_BYTE			0
 
 struct arm_spe_pmu_buf {
@@ -272,7 +290,7 @@
 	if (!attr->exclude_kernel)
 		reg |= BIT(SYS_PMSCR_EL1_E1SPE_SHIFT);
 
-	if (IS_ENABLED(CONFIG_PID_IN_CONTEXTIDR) && perfmon_capable())
+	if (get_spe_event_has_cx(event))
 		reg |= BIT(SYS_PMSCR_EL1_CX_SHIFT);
 
 	return reg;
@@ -709,10 +727,10 @@
 	    !(spe_pmu->features & SPE_PMU_FEAT_FILT_LAT))
 		return -EOPNOTSUPP;
 
+	set_spe_event_has_cx(event);
 	reg = arm_spe_event_to_pmscr(event);
 	if (!perfmon_capable() &&
 	    (reg & (BIT(SYS_PMSCR_EL1_PA_SHIFT) |
-		    BIT(SYS_PMSCR_EL1_CX_SHIFT) |
 		    BIT(SYS_PMSCR_EL1_PCT_SHIFT))))
 		return -EACCES;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/fsl_imx8_ddr_perf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/fsl_imx8_ddr_perf.c
@@ -28,13 +28,17 @@
 #define CNTL_CLEAR_MASK		0xFFFFFFFD
 #define CNTL_OVER_MASK		0xFFFFFFFE
 
+#define CNTL_CP_SHIFT		16
+#define CNTL_CP_MASK		(0xFF << CNTL_CP_SHIFT)
 #define CNTL_CSV_SHIFT		24
-#define CNTL_CSV_MASK		(0xFF << CNTL_CSV_SHIFT)
+#define CNTL_CSV_MASK		(0xFFU << CNTL_CSV_SHIFT)
 
 #define EVENT_CYCLES_ID		0
 #define EVENT_CYCLES_COUNTER	0
 #define NUM_COUNTERS		4
 
+/* For removing bias if cycle counter CNTL.CP is set to 0xf0 */
+#define CYCLES_COUNTER_MASK	0x0FFFFFFF
 #define AXI_MASKING_REVERT	0xffff0000	/* AXI_MASKING(MSB 16bits) + AXI_ID(LSB 16bits) */
 
 #define to_ddr_pmu(p)		container_of(p, struct ddr_pmu, pmu)
@@ -102,6 +106,7 @@
 	const struct fsl_ddr_devtype_data *devtype_data;
 	int irq;
 	int id;
+	int active_counter;
 };
 
 static ssize_t ddr_perf_identifier_show(struct device *dev,
@@ -428,6 +433,17 @@
 		writel(0, pmu->base + reg);
 		val = CNTL_EN | CNTL_CLEAR;
 		val |= FIELD_PREP(CNTL_CSV_MASK, config);
+
+		/*
+		 * On i.MX8MP we need to bias the cycle counter to overflow more often.
+		 * We do this by initializing bits [23:16] of the counter value via the
+		 * COUNTER_CTRL Counter Parameter (CP) field.
+		 */
+		if (pmu->devtype_data->quirks & DDR_CAP_AXI_ID_FILTER_ENHANCED) {
+			if (counter == EVENT_CYCLES_COUNTER)
+				val |= FIELD_PREP(CNTL_CP_MASK, 0xf0);
+		}
+
 		writel(val, pmu->base + reg);
 	} else {
 		/* Disable counter */
@@ -467,6 +483,12 @@
 	int ret;
 
 	new_raw_count = ddr_perf_read_counter(pmu, counter);
+	/* Remove the bias applied in ddr_perf_counter_enable(). */
+	if (pmu->devtype_data->quirks & DDR_CAP_AXI_ID_FILTER_ENHANCED) {
+		if (counter == EVENT_CYCLES_COUNTER)
+			new_raw_count &= CYCLES_COUNTER_MASK;
+	}
+
 	local64_add(new_raw_count, &event->count);
 
 	/*
@@ -496,6 +518,10 @@
 
 	ddr_perf_counter_enable(pmu, event->attr.config, counter, true);
 
+	if (!pmu->active_counter++)
+		ddr_perf_counter_enable(pmu, EVENT_CYCLES_ID,
+			EVENT_CYCLES_COUNTER, true);
+
 	hwc->state = 0;
 }
 
@@ -550,6 +576,10 @@
 	ddr_perf_counter_enable(pmu, event->attr.config, counter, false);
 	ddr_perf_event_update(event);
 
+	if (!--pmu->active_counter)
+		ddr_perf_counter_enable(pmu, EVENT_CYCLES_ID,
+			EVENT_CYCLES_COUNTER, false);
+
 	hwc->state |= PERF_HES_STOPPED;
 }
 
@@ -568,25 +598,10 @@
 
 static void ddr_perf_pmu_enable(struct pmu *pmu)
 {
-	struct ddr_pmu *ddr_pmu = to_ddr_pmu(pmu);
-
-	/* enable cycle counter if cycle is not active event list */
-	if (ddr_pmu->events[EVENT_CYCLES_COUNTER] == NULL)
-		ddr_perf_counter_enable(ddr_pmu,
-				      EVENT_CYCLES_ID,
-				      EVENT_CYCLES_COUNTER,
-				      true);
 }
 
 static void ddr_perf_pmu_disable(struct pmu *pmu)
 {
-	struct ddr_pmu *ddr_pmu = to_ddr_pmu(pmu);
-
-	if (ddr_pmu->events[EVENT_CYCLES_COUNTER] == NULL)
-		ddr_perf_counter_enable(ddr_pmu,
-				      EVENT_CYCLES_ID,
-				      EVENT_CYCLES_COUNTER,
-				      false);
 }
 
 static int ddr_perf_init(struct ddr_pmu *pmu, void __iomem *base,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/hisilicon/hisi_uncore_pa_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/hisilicon/hisi_uncore_pa_pmu.c
@@ -434,8 +434,8 @@
 	ret = perf_pmu_register(&pa_pmu->pmu, name, -1);
 	if (ret) {
 		dev_err(pa_pmu->dev, "PMU register failed, ret = %d\n", ret);
-		cpuhp_state_remove_instance(CPUHP_AP_PERF_ARM_HISI_PA_ONLINE,
-					    &pa_pmu->node);
+		cpuhp_state_remove_instance_nocalls(CPUHP_AP_PERF_ARM_HISI_PA_ONLINE,
+						    &pa_pmu->node);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/hisilicon/hisi_uncore_sllc_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/hisilicon/hisi_uncore_sllc_pmu.c
@@ -463,8 +463,8 @@
 	ret = perf_pmu_register(&sllc_pmu->pmu, name, -1);
 	if (ret) {
 		dev_err(sllc_pmu->dev, "PMU register failed, ret = %d\n", ret);
-		cpuhp_state_remove_instance(CPUHP_AP_PERF_ARM_HISI_SLLC_ONLINE,
-					    &sllc_pmu->node);
+		cpuhp_state_remove_instance_nocalls(CPUHP_AP_PERF_ARM_HISI_SLLC_ONLINE,
+						    &sllc_pmu->node);
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/perf/qcom_l2_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/perf/qcom_l2_pmu.c
@@ -736,7 +736,7 @@
 {
 	u64 mpidr;
 	int cpu_cluster_id;
-	struct cluster_pmu *cluster = NULL;
+	struct cluster_pmu *cluster;
 
 	/*
 	 * This assumes that the cluster_id is in MPIDR[aff1] for
@@ -758,10 +758,10 @@
 			 cluster->cluster_id);
 		cpumask_set_cpu(cpu, &cluster->cluster_cpus);
 		*per_cpu_ptr(l2cache_pmu->pmu_cluster, cpu) = cluster;
-		break;
+		return cluster;
 	}
 
-	return cluster;
+	return NULL;
 }
 
 static int l2cache_pmu_online_cpu(unsigned int cpu, struct hlist_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
@@ -9,6 +9,7 @@
 
 #include <linux/bitfield.h>
 #include <linux/bitops.h>
+#include <linux/bits.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/io.h>
@@ -250,7 +251,7 @@
 		     (DIV_ROUND_UP(priv->config.clk_zero, temp) << 16) |
 		     (DIV_ROUND_UP(priv->config.clk_prepare, temp) << 24));
 	regmap_write(priv->regmap, MIPI_DSI_CLK_TIM1,
-		     DIV_ROUND_UP(priv->config.clk_pre, temp));
+		     DIV_ROUND_UP(priv->config.clk_pre, BITS_PER_BYTE));
 
 	regmap_write(priv->regmap, MIPI_DSI_HS_TIM,
 		     DIV_ROUND_UP(priv->config.hs_exit, temp) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
@@ -197,7 +197,7 @@
 	struct phy_provider *phy;
 	struct device *dev = &pdev->dev;
 	struct phy_axg_mipi_pcie_analog_priv *priv;
-	struct device_node *np = dev->of_node;
+	struct device_node *np = dev->of_node, *parent_np;
 	struct regmap *map;
 	int ret;
 
@@ -206,7 +206,9 @@
 		return -ENOMEM;
 
 	/* Get the hhi system controller node */
-	map = syscon_node_to_regmap(of_get_parent(dev->of_node));
+	parent_np = of_get_parent(dev->of_node);
+	map = syscon_node_to_regmap(parent_np);
+	of_node_put(parent_np);
 	if (IS_ERR(map)) {
 		dev_err(dev,
 			"failed to get HHI regmap\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
@@ -414,19 +414,19 @@
 
 	ret = clk_prepare_enable(priv->clk_ref);
 	if (ret)
-		goto err_disable_clk_ref;
+		return ret;
 
 	priv->reset = devm_reset_control_array_get_exclusive(dev);
-	if (IS_ERR(priv->reset))
-		return PTR_ERR(priv->reset);
+	if (IS_ERR(priv->reset)) {
+		ret = PTR_ERR(priv->reset);
+		goto err_disable_clk_ref;
+	}
 
 	priv->phy = devm_phy_create(dev, np, &phy_g12a_usb3_pcie_ops);
 	if (IS_ERR(priv->phy)) {
 		ret = PTR_ERR(priv->phy);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to create PHY\n");
-
-		return ret;
+		dev_err_probe(dev, ret, "failed to create PHY\n");
+		goto err_disable_clk_ref;
 	}
 
 	phy_set_drvdata(priv->phy, priv);
@@ -434,8 +434,12 @@
 
 	phy_provider = devm_of_phy_provider_register(dev,
 						     phy_g12a_usb3_pcie_xlate);
+	if (IS_ERR(phy_provider)) {
+		ret = PTR_ERR(phy_provider);
+		goto err_disable_clk_ref;
+	}
 
-	return PTR_ERR_OR_ZERO(phy_provider);
+	return 0;
 
 err_disable_clk_ref:
 	clk_disable_unprepare(priv->clk_ref);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/amlogic/phy-meson-gxl-usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/amlogic/phy-meson-gxl-usb2.c
@@ -114,8 +114,10 @@
 		return ret;
 
 	ret = clk_prepare_enable(priv->clk);
-	if (ret)
+	if (ret) {
+		reset_control_rearm(priv->reset);
 		return ret;
+	}
 
 	return 0;
 }
@@ -125,6 +127,7 @@
 	struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
 
 	clk_disable_unprepare(priv->clk);
+	reset_control_rearm(priv->reset);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/amlogic/phy-meson8b-usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/amlogic/phy-meson8b-usb2.c
@@ -154,6 +154,7 @@
 	ret = clk_prepare_enable(priv->clk_usb_general);
 	if (ret) {
 		dev_err(&phy->dev, "Failed to enable USB general clock\n");
+		reset_control_rearm(priv->reset);
 		return ret;
 	}
 
@@ -161,6 +162,7 @@
 	if (ret) {
 		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
 		clk_disable_unprepare(priv->clk_usb_general);
+		reset_control_rearm(priv->reset);
 		return ret;
 	}
 
@@ -199,6 +201,7 @@
 				dev_warn(&phy->dev, "USB ID detect failed!\n");
 				clk_disable_unprepare(priv->clk_usb);
 				clk_disable_unprepare(priv->clk_usb_general);
+				reset_control_rearm(priv->reset);
 				return -EINVAL;
 			}
 		}
@@ -218,6 +221,7 @@
 
 	clk_disable_unprepare(priv->clk_usb);
 	clk_disable_unprepare(priv->clk_usb_general);
+	reset_control_rearm(priv->reset);
 
 	/* power off the PHY by putting it into reset mode */
 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET,
@@ -265,8 +269,9 @@
 		return PTR_ERR(priv->clk_usb);
 
 	priv->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
-	if (PTR_ERR(priv->reset) == -EPROBE_DEFER)
-		return PTR_ERR(priv->reset);
+	if (IS_ERR(priv->reset))
+		return dev_err_probe(&pdev->dev, PTR_ERR(priv->reset),
+				     "Failed to get the reset line");
 
 	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
 	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/broadcom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/broadcom/Kconfig
@@ -95,8 +95,7 @@
 	depends on OF
 	select GENERIC_PHY
 	select SOC_BRCMSTB if ARCH_BRCMSTB
-	default ARCH_BCM4908
-	default ARCH_BRCMSTB
+	default ARCH_BCM4908 || ARCH_BRCMSTB
 	help
 	  Enable this to support the Broadcom STB USB PHY.
 	  This driver is required by the USB XHCI, EHCI and OHCI
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/broadcom/phy-brcm-usb-init-synopsys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/broadcom/phy-brcm-usb-init-synopsys.c
@@ -47,6 +47,8 @@
 #define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000
 #define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK		0x00800000
 #define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK		0x00400000
+#define   USB_CTRL_USB_PM_XHC_PME_EN_MASK		0x00000010
+#define   USB_CTRL_USB_PM_XHC_S2_CLK_SWITCH_EN_MASK	0x00000008
 #define USB_CTRL_USB_PM_STATUS		0x08
 #define USB_CTRL_USB_DEVICE_CTL1	0x10
 #define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
@@ -190,10 +192,6 @@
 
 	pr_debug("%s\n", __func__);
 
-	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
-	/* 1 millisecond - for USB clocks to settle down */
-	usleep_range(1000, 2000);
-
 	if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
 		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 		reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
@@ -222,6 +220,17 @@
 		USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
 }
 
+static void usb_wake_enable_7216(struct brcm_usb_init_params *params,
+				 bool enable)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	if (enable)
+		USB_CTRL_SET(ctrl, USB_PM, XHC_PME_EN);
+	else
+		USB_CTRL_UNSET(ctrl, USB_PM, XHC_PME_EN);
+}
+
 static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
@@ -295,6 +304,26 @@
 	usb2_eye_fix_7211b0(params);
 }
 
+static void usb_init_common_7216(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	USB_CTRL_UNSET(ctrl, USB_PM, XHC_S2_CLK_SWITCH_EN);
+
+	/*
+	 * The PHY might be in a bad state if it is already powered
+	 * up. Toggle the power just in case.
+	 */
+	USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+
+	/* 1 millisecond - for USB clocks to settle down */
+	usleep_range(1000, 2000);
+
+	usb_wake_enable_7216(params, false);
+	usb_init_common(params);
+}
+
 static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
 	pr_debug("%s\n", __func__);
@@ -302,14 +331,19 @@
 	xhci_soft_reset(params, 0);
 }
 
-static void usb_uninit_common(struct brcm_usb_init_params *params)
+static void usb_uninit_common_7216(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	pr_debug("%s\n", __func__);
 
-	USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
-
+	if (params->wake_enabled) {
+		/* Switch to using slower clock during suspend to save power */
+		USB_CTRL_SET(ctrl, USB_PM, XHC_S2_CLK_SWITCH_EN);
+		usb_wake_enable_7216(params, true);
+	} else {
+		USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+	}
 }
 
 static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
@@ -371,9 +405,9 @@
 
 static const struct brcm_usb_init_ops bcm7216_ops = {
 	.init_ipp = usb_init_ipp,
-	.init_common = usb_init_common,
+	.init_common = usb_init_common_7216,
 	.init_xhci = usb_init_xhci,
-	.uninit_common = usb_uninit_common,
+	.uninit_common = usb_uninit_common_7216,
 	.uninit_xhci = usb_uninit_xhci,
 	.get_dual_select = usb_get_dual_select,
 	.set_dual_select = usb_set_dual_select,
@@ -405,5 +439,4 @@
 
 	params->family_name = "7211";
 	params->ops = &bcm7211b0_ops;
-	params->suspend_with_clocks = true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -79,6 +79,7 @@
 
 enum brcm_family_type {
 	BRCM_FAMILY_3390A0,
+	BRCM_FAMILY_4908,
 	BRCM_FAMILY_7250B0,
 	BRCM_FAMILY_7271A0,
 	BRCM_FAMILY_7364A0,
@@ -96,6 +97,7 @@
 
 static const char *family_names[BRCM_FAMILY_COUNT] = {
 	USB_BRCM_FAMILY(3390A0),
+	USB_BRCM_FAMILY(4908),
 	USB_BRCM_FAMILY(7250B0),
 	USB_BRCM_FAMILY(7271A0),
 	USB_BRCM_FAMILY(7364A0),
@@ -203,6 +205,27 @@
 		USB_CTRL_USB_PM_USB20_HC_RESETB_VAR_MASK,
 		ENDIAN_SETTINGS, /* USB_CTRL_SETUP ENDIAN bits */
 	},
+	/* 4908 */
+	[BRCM_FAMILY_4908] = {
+		0, /* USB_CTRL_SETUP_SCB1_EN_MASK */
+		0, /* USB_CTRL_SETUP_SCB2_EN_MASK */
+		0, /* USB_CTRL_SETUP_SS_EHCI64BIT_EN_MASK */
+		0, /* USB_CTRL_SETUP_STRAP_IPP_SEL_MASK */
+		0, /* USB_CTRL_SETUP_OC3_DISABLE_MASK */
+		0, /* USB_CTRL_PLL_CTL_PLL_IDDQ_PWRDN_MASK */
+		0, /* USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK */
+		USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK,
+		USB_CTRL_USB_PM_USB_PWRDN_MASK,
+		0, /* USB_CTRL_USB30_CTL1_XHC_SOFT_RESETB_MASK */
+		0, /* USB_CTRL_USB30_CTL1_USB3_IOC_MASK */
+		0, /* USB_CTRL_USB30_CTL1_USB3_IPP_MASK */
+		0, /* USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK */
+		0, /* USB_CTRL_USB_PM_SOFT_RESET_MASK */
+		0, /* USB_CTRL_SETUP_CC_DRD_MODE_ENABLE_MASK */
+		0, /* USB_CTRL_SETUP_STRAP_CC_DRD_MODE_ENABLE_SEL_MASK */
+		0, /* USB_CTRL_USB_PM_USB20_HC_RESETB_VAR_MASK */
+		0, /* USB_CTRL_SETUP ENDIAN bits */
+	},
 	/* 7250b0 */
 	[BRCM_FAMILY_7250B0] = {
 		USB_CTRL_SETUP_SCB1_EN_MASK,
@@ -559,6 +582,7 @@
 	 */
 	switch (params->selected_family) {
 	case BRCM_FAMILY_3390A0:
+	case BRCM_FAMILY_4908:
 	case BRCM_FAMILY_7250B0:
 	case BRCM_FAMILY_7366C0:
 	case BRCM_FAMILY_74371A0:
@@ -1004,6 +1028,18 @@
 	.set_dual_select = usb_set_dual_select,
 };
 
+void brcm_usb_dvr_init_4908(struct brcm_usb_init_params *params)
+{
+	int fam;
+
+	fam = BRCM_FAMILY_4908;
+	params->selected_family = fam;
+	params->usb_reg_bits_map =
+		&usb_reg_bits_map_table[fam][0];
+	params->family_name = family_names[fam];
+	params->ops = &bcm7445_ops;
+}
+
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
 {
 	int fam;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -61,9 +61,9 @@
 	const struct brcm_usb_init_ops *ops;
 	struct regmap *syscon_piarbctl;
 	bool wake_enabled;
-	bool suspend_with_clocks;
 };
 
+void brcm_usb_dvr_init_4908(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/broadcom/phy-brcm-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/broadcom/phy-brcm-usb.c
@@ -18,6 +18,7 @@
 #include <linux/soc/brcmstb/brcmstb.h>
 #include <dt-bindings/phy/phy.h>
 #include <linux/mfd/syscon.h>
+#include <linux/suspend.h>
 
 #include "phy-brcm-usb-init.h"
 
@@ -70,17 +71,40 @@
 	int			init_count;
 	int			wake_irq;
 	struct brcm_usb_phy	phys[BRCM_USB_PHY_ID_MAX];
+	struct notifier_block	pm_notifier;
+	bool			pm_active;
 };
 
 static s8 *node_reg_names[BRCM_REGS_MAX] = {
 	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
 };
 
+static int brcm_pm_notifier(struct notifier_block *notifier,
+			    unsigned long pm_event,
+			    void *unused)
+{
+	struct brcm_usb_phy_data *priv =
+		container_of(notifier, struct brcm_usb_phy_data, pm_notifier);
+
+	switch (pm_event) {
+	case PM_HIBERNATION_PREPARE:
+	case PM_SUSPEND_PREPARE:
+		priv->pm_active = true;
+		break;
+	case PM_POST_RESTORE:
+	case PM_POST_HIBERNATION:
+	case PM_POST_SUSPEND:
+		priv->pm_active = false;
+		break;
+	}
+	return NOTIFY_DONE;
+}
+
 static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
 {
-	struct phy *gphy = dev_id;
+	struct device *dev = dev_id;
 
-	pm_wakeup_event(&gphy->dev, 0);
+	pm_wakeup_event(dev, 0);
 
 	return IRQ_HANDLED;
 }
@@ -91,6 +115,9 @@
 	struct brcm_usb_phy_data *priv =
 		container_of(phy, struct brcm_usb_phy_data, phys[phy->id]);
 
+	if (priv->pm_active)
+		return 0;
+
 	/*
 	 * Use a lock to make sure a second caller waits until
 	 * the base phy is inited before using it.
@@ -120,6 +147,9 @@
 	struct brcm_usb_phy_data *priv =
 		container_of(phy, struct brcm_usb_phy_data, phys[phy->id]);
 
+	if (priv->pm_active)
+		return 0;
+
 	dev_dbg(&gphy->dev, "EXIT\n");
 	if (phy->id == BRCM_USB_PHY_2_0)
 		brcm_usb_uninit_eohci(&priv->ini);
@@ -253,6 +283,15 @@
 	.attrs = brcm_usb_phy_attrs,
 };
 
+static const struct match_chip_info chip_info_4908 = {
+	.init_func = &brcm_usb_dvr_init_4908,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		-1,
+	},
+};
+
 static const struct match_chip_info chip_info_7216 = {
 	.init_func = &brcm_usb_dvr_init_7216,
 	.required_regs = {
@@ -288,7 +327,7 @@
 static const struct of_device_id brcm_usb_dt_ids[] = {
 	{
 		.compatible = "brcm,bcm4908-usb-phy",
-		.data = &chip_info_7445,
+		.data = &chip_info_4908,
 	},
 	{
 		.compatible = "brcm,bcm7216-usb-phy",
@@ -412,7 +451,7 @@
 	if (priv->wake_irq >= 0) {
 		err = devm_request_irq(dev, priv->wake_irq,
 				       brcm_usb_phy_wake_isr, 0,
-				       dev_name(dev), gphy);
+				       dev_name(dev), dev);
 		if (err < 0)
 			return err;
 		device_set_wakeup_capable(dev, 1);
@@ -488,6 +527,9 @@
 	if (err)
 		return err;
 
+	priv->pm_notifier.notifier_call = brcm_pm_notifier;
+	register_pm_notifier(&priv->pm_notifier);
+
 	mutex_init(&priv->mutex);
 
 	/* make sure invert settings are correct */
@@ -528,7 +570,10 @@
 
 static int brcm_usb_phy_remove(struct platform_device *pdev)
 {
+	struct brcm_usb_phy_data *priv = dev_get_drvdata(&pdev->dev);
+
 	sysfs_remove_group(&pdev->dev.kobj, &brcm_usb_phy_group);
+	unregister_pm_notifier(&priv->pm_notifier);
 
 	return 0;
 }
@@ -539,6 +584,7 @@
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
+		dev_dbg(dev, "SUSPEND\n");
 		priv->ini.wake_enabled = device_may_wakeup(dev);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			brcm_usb_uninit_xhci(&priv->ini);
@@ -552,7 +598,7 @@
 		 * and newer XHCI->2.0-clks/3.0-clks.
 		 */
 
-		if (!priv->ini.suspend_with_clocks) {
+		if (!priv->ini.wake_enabled) {
 			if (priv->phys[BRCM_USB_PHY_3_0].inited)
 				clk_disable_unprepare(priv->usb_30_clk);
 			if (priv->phys[BRCM_USB_PHY_2_0].inited ||
@@ -569,8 +615,10 @@
 {
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
-	clk_prepare_enable(priv->usb_20_clk);
-	clk_prepare_enable(priv->usb_30_clk);
+	if (!priv->ini.wake_enabled) {
+		clk_prepare_enable(priv->usb_20_clk);
+		clk_prepare_enable(priv->usb_30_clk);
+	}
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -578,6 +626,7 @@
 	 * Uninitialize anything that wasn't previously initialized.
 	 */
 	if (priv->init_count) {
+		dev_dbg(dev, "RESUME\n");
 		if (priv->wake_irq >= 0)
 			disable_irq_wake(priv->wake_irq);
 		brcm_usb_init_common(&priv->ini);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/cadence/phy-cadence-sierra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/cadence/phy-cadence-sierra.c
@@ -215,7 +215,10 @@
 	[CMN_PLLLC1] = { PLL1_REFCLK, PLL0_REFCLK },
 };
 
-static u32 cdns_sierra_pll_mux_table[] = { 0, 1 };
+static u32 cdns_sierra_pll_mux_table[][SIERRA_NUM_CMN_PLLC_PARENTS] = {
+	[CMN_PLLLC] = { 0, 1 },
+	[CMN_PLLLC1] = { 1, 0 },
+};
 
 struct cdns_sierra_inst {
 	struct phy *phy;
@@ -436,11 +439,25 @@
 static u8 cdns_sierra_pll_mux_get_parent(struct clk_hw *hw)
 {
 	struct cdns_sierra_pll_mux *mux = to_cdns_sierra_pll_mux(hw);
+	struct regmap_field *plllc1en_field = mux->plllc1en_field;
+	struct regmap_field *termen_field = mux->termen_field;
 	struct regmap_field *field = mux->pfdclk_sel_preg;
 	unsigned int val;
+	int index;
 
 	regmap_field_read(field, &val);
-	return clk_mux_val_to_index(hw, cdns_sierra_pll_mux_table, 0, val);
+
+	if (strstr(clk_hw_get_name(hw), clk_names[CDNS_SIERRA_PLL_CMNLC1])) {
+		index = clk_mux_val_to_index(hw, cdns_sierra_pll_mux_table[CMN_PLLLC1], 0, val);
+		if (index == 1) {
+			regmap_field_write(plllc1en_field, 1);
+			regmap_field_write(termen_field, 1);
+		}
+	} else {
+		index = clk_mux_val_to_index(hw, cdns_sierra_pll_mux_table[CMN_PLLLC], 0, val);
+	}
+
+	return index;
 }
 
 static int cdns_sierra_pll_mux_set_parent(struct clk_hw *hw, u8 index)
@@ -458,7 +475,11 @@
 		ret |= regmap_field_write(termen_field, 1);
 	}
 
-	val = cdns_sierra_pll_mux_table[index];
+	if (strstr(clk_hw_get_name(hw), clk_names[CDNS_SIERRA_PLL_CMNLC1]))
+		val = cdns_sierra_pll_mux_table[CMN_PLLLC1][index];
+	else
+		val = cdns_sierra_pll_mux_table[CMN_PLLLC][index];
+
 	ret |= regmap_field_write(field, val);
 
 	return ret;
@@ -496,8 +517,8 @@
 	for (i = 0; i < num_parents; i++) {
 		clk = sp->input_clks[pll_mux_parent_index[clk_index][i]];
 		if (IS_ERR_OR_NULL(clk)) {
-			dev_err(dev, "No parent clock for derived_refclk\n");
-			return PTR_ERR(clk);
+			dev_err(dev, "No parent clock for PLL mux clocks\n");
+			return IS_ERR(clk) ? PTR_ERR(clk) : -ENOENT;
 		}
 		parent_names[i] = __clk_get_name(clk);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/cadence/phy-cadence-torrent.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/cadence/phy-cadence-torrent.c
@@ -1056,6 +1056,9 @@
 	ret = regmap_read_poll_timeout(regmap, PHY_PMA_XCVR_POWER_STATE_ACK,
 				       read_val, (read_val & mask) == value, 0,
 				       POLL_TIMEOUT_US);
+	if (ret)
+		return ret;
+
 	cdns_torrent_dp_write(regmap, PHY_PMA_XCVR_POWER_STATE_REQ, 0x00000000);
 	ndelay(100);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
@@ -153,7 +153,7 @@
 		phy_set_drvdata(phy, &priv->ports[i]);
 		i++;
 
-		if (i > INNO_PHY_PORT_NUM) {
+		if (i >= INNO_PHY_PORT_NUM) {
 			dev_warn(dev, "Support %d ports in maximum\n", i);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/mediatek/phy-mtk-mipi-dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/mediatek/phy-mtk-mipi-dsi.c
@@ -146,6 +146,8 @@
 		return -ENOMEM;
 
 	mipi_tx->driver_data = of_device_get_match_data(dev);
+	if (!mipi_tx->driver_data)
+		return -ENODEV;
 
 	mipi_tx->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(mipi_tx->regs))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/mediatek/phy-mtk-tphy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -12,6 +12,7 @@
 #include <linux/iopoll.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
+#include <linux/nvmem-consumer.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
@@ -41,6 +42,9 @@
 #define SSUSB_SIFSLV_V2_U3PHYD		0x200
 #define SSUSB_SIFSLV_V2_U3PHYA		0x400
 
+#define U3P_MISC_REG1		0x04
+#define MR1_EFUSE_AUTO_LOAD_DIS		BIT(6)
+
 #define U3P_USBPHYACR0		0x000
 #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
 #define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
@@ -133,6 +137,8 @@
 #define P3C_RG_SWRST_U3_PHYD_FORCE_EN	BIT(24)
 
 #define U3P_U3_PHYA_REG0	0x000
+#define P3A_RG_IEXT_INTR		GENMASK(15, 10)
+#define P3A_RG_IEXT_INTR_VAL(x)		((0x3f & (x)) << 10)
 #define P3A_RG_CLKDRV_OFF		GENMASK(3, 2)
 #define P3A_RG_CLKDRV_OFF_VAL(x)	((0x3 & (x)) << 2)
 
@@ -187,6 +193,19 @@
 #define P3D_RG_FWAKE_TH		GENMASK(21, 16)
 #define P3D_RG_FWAKE_TH_VAL(x)	((0x3f & (x)) << 16)
 
+#define U3P_U3_PHYD_IMPCAL0		0x010
+#define P3D_RG_FORCE_TX_IMPEL		BIT(31)
+#define P3D_RG_TX_IMPEL			GENMASK(28, 24)
+#define P3D_RG_TX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
+
+#define U3P_U3_PHYD_IMPCAL1		0x014
+#define P3D_RG_FORCE_RX_IMPEL		BIT(31)
+#define P3D_RG_RX_IMPEL			GENMASK(28, 24)
+#define P3D_RG_RX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
+
+#define U3P_U3_PHYD_RSV			0x054
+#define P3D_RG_EFUSE_AUTO_LOAD_DIS	BIT(12)
+
 #define U3P_U3_PHYD_CDR1		0x05c
 #define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
 #define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
@@ -307,6 +326,11 @@
 	 * 48M PLL, fix it by switching PLL to 26M from default 48M
 	 */
 	bool sw_pll_48m_to_26m;
+	/*
+	 * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse,
+	 * support sw way, also support it for v2/v3 optionally.
+	 */
+	bool sw_efuse_supported;
 	enum mtk_phy_version version;
 };
 
@@ -336,6 +360,10 @@
 	struct regmap *type_sw;
 	u32 type_sw_reg;
 	u32 type_sw_index;
+	u32 efuse_sw_en;
+	u32 efuse_intr;
+	u32 efuse_tx_imp;
+	u32 efuse_rx_imp;
 	int eye_src;
 	int eye_vrt;
 	int eye_term;
@@ -1011,7 +1039,7 @@
 static int phy_type_set(struct mtk_phy_instance *instance)
 {
 	int type;
-	u32 mask;
+	u32 offset;
 
 	if (!instance->type_sw)
 		return 0;
@@ -1034,12 +1062,137 @@
 		return 0;
 	}
 
-	mask = RG_PHY_SW_TYPE << (instance->type_sw_index * BITS_PER_BYTE);
-	regmap_update_bits(instance->type_sw, instance->type_sw_reg, mask, type);
+	offset = instance->type_sw_index * BITS_PER_BYTE;
+	regmap_update_bits(instance->type_sw, instance->type_sw_reg,
+			   RG_PHY_SW_TYPE << offset, type << offset);
 
 	return 0;
 }
 
+static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance)
+{
+	struct device *dev = &instance->phy->dev;
+	int ret = 0;
+
+	/* tphy v1 doesn't support sw efuse, skip it */
+	if (!tphy->pdata->sw_efuse_supported) {
+		instance->efuse_sw_en = 0;
+		return 0;
+	}
+
+	/* software efuse is optional */
+	instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells");
+	if (!instance->efuse_sw_en)
+		return 0;
+
+	switch (instance->type) {
+	case PHY_TYPE_USB2:
+		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
+		if (ret) {
+			dev_err(dev, "fail to get u2 intr efuse, %d\n", ret);
+			break;
+		}
+
+		/* no efuse, ignore it */
+		if (!instance->efuse_intr) {
+			dev_warn(dev, "no u2 intr efuse, but dts enable it\n");
+			instance->efuse_sw_en = 0;
+			break;
+		}
+
+		dev_dbg(dev, "u2 efuse - intr %x\n", instance->efuse_intr);
+		break;
+
+	case PHY_TYPE_USB3:
+	case PHY_TYPE_PCIE:
+		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
+		if (ret) {
+			dev_err(dev, "fail to get u3 intr efuse, %d\n", ret);
+			break;
+		}
+
+		ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp);
+		if (ret) {
+			dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret);
+			break;
+		}
+
+		ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp);
+		if (ret) {
+			dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret);
+			break;
+		}
+
+		/* no efuse, ignore it */
+		if (!instance->efuse_intr &&
+		    !instance->efuse_rx_imp &&
+		    !instance->efuse_tx_imp) {
+			dev_warn(dev, "no u3 intr efuse, but dts enable it\n");
+			instance->efuse_sw_en = 0;
+			break;
+		}
+
+		dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n",
+			instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp);
+		break;
+	default:
+		dev_err(dev, "no sw efuse for type %d\n", instance->type);
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static void phy_efuse_set(struct mtk_phy_instance *instance)
+{
+	struct device *dev = &instance->phy->dev;
+	struct u2phy_banks *u2_banks = &instance->u2_banks;
+	struct u3phy_banks *u3_banks = &instance->u3_banks;
+	u32 tmp;
+
+	if (!instance->efuse_sw_en)
+		return;
+
+	switch (instance->type) {
+	case PHY_TYPE_USB2:
+		tmp = readl(u2_banks->misc + U3P_MISC_REG1);
+		tmp |= MR1_EFUSE_AUTO_LOAD_DIS;
+		writel(tmp, u2_banks->misc + U3P_MISC_REG1);
+
+		tmp = readl(u2_banks->com + U3P_USBPHYACR1);
+		tmp &= ~PA1_RG_INTR_CAL;
+		tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr);
+		writel(tmp, u2_banks->com + U3P_USBPHYACR1);
+		break;
+	case PHY_TYPE_USB3:
+	case PHY_TYPE_PCIE:
+		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV);
+		tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS;
+		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV);
+
+		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
+		tmp &= ~P3D_RG_TX_IMPEL;
+		tmp |= P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp);
+		tmp |= P3D_RG_FORCE_TX_IMPEL;
+		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
+
+		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
+		tmp &= ~P3D_RG_RX_IMPEL;
+		tmp |= P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp);
+		tmp |= P3D_RG_FORCE_RX_IMPEL;
+		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
+
+		tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_IEXT_INTR;
+		tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr);
+		writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0);
+		break;
+	default:
+		dev_warn(dev, "no sw efuse for type %d\n", instance->type);
+		break;
+	}
+}
+
 static int mtk_phy_init(struct phy *phy)
 {
 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
@@ -1050,6 +1203,8 @@
 	if (ret)
 		return ret;
 
+	phy_efuse_set(instance);
+
 	switch (instance->type) {
 	case PHY_TYPE_USB2:
 		u2_phy_instance_init(tphy, instance);
@@ -1134,6 +1289,7 @@
 	struct mtk_phy_instance *instance = NULL;
 	struct device_node *phy_np = args->np;
 	int index;
+	int ret;
 
 	if (args->args_count != 1) {
 		dev_err(dev, "invalid number of cells in 'phy' property\n");
@@ -1174,6 +1330,10 @@
 		return ERR_PTR(-EINVAL);
 	}
 
+	ret = phy_efuse_get(tphy, instance);
+	if (ret)
+		return ERR_PTR(ret);
+
 	phy_parse_property(tphy, instance);
 	phy_type_set(instance);
 
@@ -1196,10 +1356,12 @@
 
 static const struct mtk_phy_pdata tphy_v2_pdata = {
 	.avoid_rx_sen_degradation = false,
+	.sw_efuse_supported = true,
 	.version = MTK_PHY_V2,
 };
 
 static const struct mtk_phy_pdata tphy_v3_pdata = {
+	.sw_efuse_supported = true,
 	.version = MTK_PHY_V3,
 };
 
@@ -1210,6 +1372,7 @@
 
 static const struct mtk_phy_pdata mt8195_pdata = {
 	.sw_pll_48m_to_26m = true,
+	.sw_efuse_supported = true,
 	.version = MTK_PHY_V3,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/microchip/sparx5_serdes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/microchip/sparx5_serdes.c
@@ -2475,10 +2475,10 @@
 		return -EINVAL;
 	}
 	iomem = devm_ioremap(priv->dev, iores->start, resource_size(iores));
-	if (IS_ERR(iomem)) {
+	if (!iomem) {
 		dev_err(priv->dev, "Unable to get serdes registers: %s\n",
 			iores->name);
-		return PTR_ERR(iomem);
+		return -ENOMEM;
 	}
 	for (idx = 0; idx < ARRAY_SIZE(sparx5_serdes_iomap); idx++) {
 		struct sparx5_serdes_io_resource *iomap = &sparx5_serdes_iomap[idx];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/motorola/phy-mapphone-mdm6600.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/motorola/phy-mapphone-mdm6600.c
@@ -122,16 +122,10 @@
 {
 	struct phy_mdm6600 *ddata = phy_get_drvdata(x);
 	struct gpio_desc *enable_gpio = ddata->ctrl_gpios[PHY_MDM6600_ENABLE];
-	int error;
 
 	if (!ddata->enabled)
 		return -ENODEV;
 
-	error = pinctrl_pm_select_default_state(ddata->dev);
-	if (error)
-		dev_warn(ddata->dev, "%s: error with default_state: %i\n",
-			 __func__, error);
-
 	gpiod_set_value_cansleep(enable_gpio, 1);
 
 	/* Allow aggressive PM for USB, it's only needed for n_gsm port */
@@ -160,11 +154,6 @@
 
 	gpiod_set_value_cansleep(enable_gpio, 0);
 
-	error = pinctrl_pm_select_sleep_state(ddata->dev);
-	if (error)
-		dev_warn(ddata->dev, "%s: error with sleep_state: %i\n",
-			 __func__, error);
-
 	return 0;
 }
 
@@ -456,6 +445,7 @@
 {
 	struct gpio_desc *reset_gpio =
 		ddata->ctrl_gpios[PHY_MDM6600_RESET];
+	int error;
 
 	ddata->enabled = false;
 	phy_mdm6600_cmd(ddata, PHY_MDM6600_CMD_BP_SHUTDOWN_REQ);
@@ -471,6 +461,17 @@
 	} else {
 		dev_err(ddata->dev, "Timed out powering down\n");
 	}
+
+	/*
+	 * Keep reset gpio high with padconf internal pull-up resistor to
+	 * prevent modem from waking up during deeper SoC idle states. The
+	 * gpio bank lines can have glitches if not in the always-on wkup
+	 * domain.
+	 */
+	error = pinctrl_pm_select_sleep_state(ddata->dev);
+	if (error)
+		dev_warn(ddata->dev, "%s: error with sleep_state: %i\n",
+			 __func__, error);
 }
 
 static void phy_mdm6600_deferred_power_on(struct work_struct *work)
@@ -571,12 +572,6 @@
 	ddata->dev = &pdev->dev;
 	platform_set_drvdata(pdev, ddata);
 
-	/* Active state selected in phy_mdm6600_power_on() */
-	error = pinctrl_pm_select_sleep_state(ddata->dev);
-	if (error)
-		dev_warn(ddata->dev, "%s: error with sleep_state: %i\n",
-			 __func__, error);
-
 	error = phy_mdm6600_init_lines(ddata);
 	if (error)
 		return error;
@@ -627,8 +622,11 @@
 	pm_runtime_put_autosuspend(ddata->dev);
 
 cleanup:
-	if (error < 0)
+	if (error < 0) {
 		phy_mdm6600_device_power_off(ddata);
+		pm_runtime_disable(ddata->dev);
+		pm_runtime_dont_use_autosuspend(ddata->dev);
+	}
 
 	return error;
 }
@@ -638,6 +636,7 @@
 	struct phy_mdm6600 *ddata = platform_get_drvdata(pdev);
 	struct gpio_desc *reset_gpio = ddata->ctrl_gpios[PHY_MDM6600_RESET];
 
+	pm_runtime_get_noresume(ddata->dev);
 	pm_runtime_dont_use_autosuspend(ddata->dev);
 	pm_runtime_put_sync(ddata->dev);
 	pm_runtime_disable(ddata->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/phy-can-transceiver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/phy-can-transceiver.c
@@ -87,6 +87,7 @@
 	struct gpio_desc *standby_gpio;
 	struct gpio_desc *enable_gpio;
 	u32 max_bitrate = 0;
+	int err;
 
 	can_transceiver_phy = devm_kzalloc(dev, sizeof(struct can_transceiver_phy), GFP_KERNEL);
 	if (!can_transceiver_phy)
@@ -102,8 +103,8 @@
 		return PTR_ERR(phy);
 	}
 
-	device_property_read_u32(dev, "max-bitrate", &max_bitrate);
-	if (!max_bitrate)
+	err = device_property_read_u32(dev, "max-bitrate", &max_bitrate);
+	if ((err != -EINVAL) && !max_bitrate)
 		dev_warn(dev, "Invalid value for transceiver max bitrate. Ignoring bitrate limit\n");
 	phy->attrs.max_link_rate = max_bitrate;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/phy-core-mipi-dphy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/phy-core-mipi-dphy.c
@@ -36,7 +36,7 @@
 
 	cfg->clk_miss = 0;
 	cfg->clk_post = 60000 + 52 * ui;
-	cfg->clk_pre = 8000;
+	cfg->clk_pre = 8;
 	cfg->clk_prepare = 38000;
 	cfg->clk_settle = 95000;
 	cfg->clk_term_en = 0;
@@ -64,10 +64,10 @@
 	cfg->hs_trail = max(4 * 8 * ui, 60000 + 4 * 4 * ui);
 
 	cfg->init = 100;
-	cfg->lpx = 60000;
+	cfg->lpx = 50000;
 	cfg->ta_get = 5 * cfg->lpx;
 	cfg->ta_go = 4 * cfg->lpx;
-	cfg->ta_sure = 2 * cfg->lpx;
+	cfg->ta_sure = cfg->lpx;
 	cfg->wakeup = 1000;
 
 	cfg->hs_clk_rate = hs_clk_rate;
@@ -97,7 +97,7 @@
 	if (cfg->clk_post < (60000 + 52 * ui))
 		return -EINVAL;
 
-	if (cfg->clk_pre < 8000)
+	if (cfg->clk_pre < 8)
 		return -EINVAL;
 
 	if (cfg->clk_prepare < 38000 || cfg->clk_prepare > 95000)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/phy-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/phy-core.c
@@ -138,8 +138,10 @@
 			return phy_provider;
 
 		for_each_child_of_node(phy_provider->children, child)
-			if (child == node)
+			if (child == node) {
+				of_node_put(child);
 				return phy_provider;
+			}
 	}
 
 	return ERR_PTR(-EPROBE_DEFER);
@@ -537,8 +539,10 @@
 		return ERR_PTR(-ENODEV);
 
 	/* This phy type handled by the usb-phy subsystem for now */
-	if (of_device_is_compatible(args.np, "usb-nop-xceiv"))
-		return ERR_PTR(-ENODEV);
+	if (of_device_is_compatible(args.np, "usb-nop-xceiv")) {
+		phy = ERR_PTR(-ENODEV);
+		goto out_put_node;
+	}
 
 	mutex_lock(&phy_provider_mutex);
 	phy_provider = of_phy_provider_lookup(args.np);
@@ -560,6 +564,7 @@
 
 out_unlock:
 	mutex_unlock(&phy_provider_mutex);
+out_put_node:
 	of_node_put(args.np);
 
 	return phy;
@@ -645,7 +650,7 @@
 	if (!phy)
 		return;
 
-	r = devres_destroy(dev, devm_phy_release, devm_phy_match, phy);
+	r = devres_release(dev, devm_phy_release, devm_phy_match, phy);
 	dev_WARN_ONCE(dev, r, "couldn't find PHY resource\n");
 }
 EXPORT_SYMBOL_GPL(devm_phy_put);
@@ -1018,7 +1023,7 @@
 {
 	int r;
 
-	r = devres_destroy(dev, devm_phy_consume, devm_phy_match, phy);
+	r = devres_release(dev, devm_phy_consume, devm_phy_match, phy);
 	dev_WARN_ONCE(dev, r, "couldn't find PHY resource\n");
 }
 EXPORT_SYMBOL_GPL(devm_phy_destroy);
@@ -1156,12 +1161,12 @@
  * of_phy_provider_unregister to unregister the phy provider.
  */
 void devm_of_phy_provider_unregister(struct device *dev,
-	struct phy_provider *phy_provider)
+				     struct phy_provider *phy_provider)
 {
 	int r;
 
-	r = devres_destroy(dev, devm_phy_provider_release, devm_phy_match,
-		phy_provider);
+	r = devres_release(dev, devm_phy_provider_release, devm_phy_match,
+			   phy_provider);
 	dev_WARN_ONCE(dev, r, "couldn't find PHY provider device resource\n");
 }
 EXPORT_SYMBOL_GPL(devm_of_phy_provider_unregister);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -2919,6 +2919,7 @@
 	struct regulator_bulk_data *vregs;
 
 	struct qmp_phy **phys;
+	struct qmp_phy *usb_phy;
 
 	struct mutex phy_mutex;
 	int init_count;
@@ -3417,8 +3418,8 @@
 
 	.clk_list		= qmp_v3_phy_clk_l,
 	.num_clks		= ARRAY_SIZE(qmp_v3_phy_clk_l),
-	.reset_list		= sc7180_usb3phy_reset_l,
-	.num_resets		= ARRAY_SIZE(sc7180_usb3phy_reset_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
 	.vreg_list		= qmp_phy_vreg_l,
 	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
 	.regs			= qmp_v3_usb3phy_regs_layout,
@@ -3632,7 +3633,7 @@
 	.nlanes = 1,
 
 	.serdes_tbl		= sc8180x_qmp_pcie_serdes_tbl,
-	.serdes_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_serdes_tbl),
+	.serdes_tbl_num		= ARRAY_SIZE(sc8180x_qmp_pcie_serdes_tbl),
 	.tx_tbl			= sc8180x_qmp_pcie_tx_tbl,
 	.tx_tbl_num		= ARRAY_SIZE(sc8180x_qmp_pcie_tx_tbl),
 	.rx_tbl			= sc8180x_qmp_pcie_rx_tbl,
@@ -3805,8 +3806,8 @@
 	.serdes_tbl_hbr3	= qmp_v4_dp_serdes_tbl_hbr3,
 	.serdes_tbl_hbr3_num	= ARRAY_SIZE(qmp_v4_dp_serdes_tbl_hbr3),
 
-	.clk_list		= qmp_v4_phy_clk_l,
-	.num_clks		= ARRAY_SIZE(qmp_v4_phy_clk_l),
+	.clk_list		= qmp_v4_sm8250_usbphy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_sm8250_usbphy_clk_l),
 	.reset_list		= msm8996_usb3phy_reset_l,
 	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
 	.vreg_list		= qmp_phy_vreg_l,
@@ -4554,7 +4555,7 @@
 	struct qcom_qmp *qmp = qphy->qmp;
 	const struct qmp_phy_cfg *cfg = qphy->cfg;
 	void __iomem *serdes = qphy->serdes;
-	void __iomem *pcs = qphy->pcs;
+	struct qmp_phy *usb_phy = qmp->usb_phy;
 	void __iomem *dp_com = qmp->dp_com;
 	int ret, i;
 
@@ -4620,13 +4621,13 @@
 		qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
 			     SW_PWRDN);
 	} else {
-		if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL])
-			qphy_setbits(pcs,
-					cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
-					cfg->pwrdn_ctrl);
+		if (usb_phy->cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL])
+			qphy_setbits(usb_phy->pcs,
+					usb_phy->cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
+					usb_phy->cfg->pwrdn_ctrl);
 		else
-			qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL,
-					cfg->pwrdn_ctrl);
+			qphy_setbits(usb_phy->pcs, QPHY_POWER_DOWN_CONTROL,
+					usb_phy->cfg->pwrdn_ctrl);
 	}
 
 	mutex_unlock(&qmp->phy_mutex);
@@ -4802,7 +4803,7 @@
 
 	ret = reset_control_deassert(qmp->ufs_reset);
 	if (ret)
-		goto err_lane_rst;
+		goto err_pcs_ready;
 
 	qcom_qmp_phy_configure(pcs_misc, cfg->regs, cfg->pcs_misc_tbl,
 			       cfg->pcs_misc_tbl_num);
@@ -4984,7 +4985,7 @@
 static int __maybe_unused qcom_qmp_phy_runtime_suspend(struct device *dev)
 {
 	struct qcom_qmp *qmp = dev_get_drvdata(dev);
-	struct qmp_phy *qphy = qmp->phys[0];
+	struct qmp_phy *qphy = qmp->usb_phy;
 	const struct qmp_phy_cfg *cfg = qphy->cfg;
 
 	dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qphy->mode);
@@ -5009,7 +5010,7 @@
 static int __maybe_unused qcom_qmp_phy_runtime_resume(struct device *dev)
 {
 	struct qcom_qmp *qmp = dev_get_drvdata(dev);
-	struct qmp_phy *qphy = qmp->phys[0];
+	struct qmp_phy *qphy = qmp->usb_phy;
 	const struct qmp_phy_cfg *cfg = qphy->cfg;
 	int ret = 0;
 
@@ -5382,6 +5383,26 @@
 	.owner		= THIS_MODULE,
 };
 
+static void qcom_qmp_reset_control_put(void *data)
+{
+	reset_control_put(data);
+}
+
+static void __iomem *qmp_usb_iomap(struct device *dev, struct device_node *np,
+		int index, bool exclusive)
+{
+	struct resource res;
+
+	if (!exclusive) {
+		if (of_address_to_resource(np, index, &res))
+			return IOMEM_ERR_PTR(-EINVAL);
+
+		return devm_ioremap(dev, res.start, resource_size(&res));
+	}
+
+	return devm_of_iomap(dev, np, index, NULL);
+}
+
 static
 int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id,
 			void __iomem *serdes, const struct qmp_phy_cfg *cfg)
@@ -5391,8 +5412,18 @@
 	struct qmp_phy *qphy;
 	const struct phy_ops *ops;
 	char prop_name[MAX_PROP_NAME];
+	bool exclusive = true;
 	int ret;
 
+	/*
+	 * FIXME: These bindings should be fixed to not rely on overlapping
+	 *        mappings for PCS.
+	 */
+	if (of_device_is_compatible(dev->of_node, "qcom,sdx65-qmp-usb3-uni-phy"))
+		exclusive = false;
+	if (of_device_is_compatible(dev->of_node, "qcom,sm8350-qmp-usb3-uni-phy"))
+		exclusive = false;
+
 	qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
 	if (!qphy)
 		return -ENOMEM;
@@ -5405,17 +5436,17 @@
 	 * For dual lane PHYs: tx2 -> 3, rx2 -> 4, pcs_misc (optional) -> 5
 	 * For single lane PHYs: pcs_misc (optional) -> 3.
 	 */
-	qphy->tx = of_iomap(np, 0);
-	if (!qphy->tx)
-		return -ENOMEM;
-
-	qphy->rx = of_iomap(np, 1);
-	if (!qphy->rx)
-		return -ENOMEM;
-
-	qphy->pcs = of_iomap(np, 2);
-	if (!qphy->pcs)
-		return -ENOMEM;
+	qphy->tx = devm_of_iomap(dev, np, 0, NULL);
+	if (IS_ERR(qphy->tx))
+		return PTR_ERR(qphy->tx);
+
+	qphy->rx = devm_of_iomap(dev, np, 1, NULL);
+	if (IS_ERR(qphy->rx))
+		return PTR_ERR(qphy->rx);
+
+	qphy->pcs = qmp_usb_iomap(dev, np, 2, exclusive);
+	if (IS_ERR(qphy->pcs))
+		return PTR_ERR(qphy->pcs);
 
 	/*
 	 * If this is a dual-lane PHY, then there should be registers for the
@@ -5424,9 +5455,9 @@
 	 * offset from the first lane.
 	 */
 	if (cfg->is_dual_lane_phy) {
-		qphy->tx2 = of_iomap(np, 3);
-		qphy->rx2 = of_iomap(np, 4);
-		if (!qphy->tx2 || !qphy->rx2) {
+		qphy->tx2 = devm_of_iomap(dev, np, 3, NULL);
+		qphy->rx2 = devm_of_iomap(dev, np, 4, NULL);
+		if (IS_ERR(qphy->tx2) || IS_ERR(qphy->rx2)) {
 			dev_warn(dev,
 				 "Underspecified device tree, falling back to legacy register regions\n");
 
@@ -5436,15 +5467,17 @@
 			qphy->rx2 = qphy->rx + QMP_PHY_LEGACY_LANE_STRIDE;
 
 		} else {
-			qphy->pcs_misc = of_iomap(np, 5);
+			qphy->pcs_misc = devm_of_iomap(dev, np, 5, NULL);
 		}
 
 	} else {
-		qphy->pcs_misc = of_iomap(np, 3);
+		qphy->pcs_misc = devm_of_iomap(dev, np, 3, NULL);
 	}
 
-	if (!qphy->pcs_misc)
+	if (IS_ERR(qphy->pcs_misc)) {
 		dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
+		qphy->pcs_misc = NULL;
+	}
 
 	/*
 	 * Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3
@@ -5454,7 +5487,7 @@
 	 * all phys that don't need this.
 	 */
 	snprintf(prop_name, sizeof(prop_name), "pipe%d", id);
-	qphy->pipe_clk = of_clk_get_by_name(np, prop_name);
+	qphy->pipe_clk = devm_get_clk_from_child(dev, np, prop_name);
 	if (IS_ERR(qphy->pipe_clk)) {
 		if (cfg->type == PHY_TYPE_PCIE ||
 		    cfg->type == PHY_TYPE_USB3) {
@@ -5476,6 +5509,10 @@
 			dev_err(dev, "failed to get lane%d reset\n", id);
 			return PTR_ERR(qphy->lane_rst);
 		}
+		ret = devm_add_action_or_reset(dev, qcom_qmp_reset_control_put,
+					       qphy->lane_rst);
+		if (ret)
+			return ret;
 	}
 
 	if (cfg->type == PHY_TYPE_UFS || cfg->type == PHY_TYPE_PCIE)
@@ -5731,7 +5768,9 @@
 		return -ENOMEM;
 
 	pm_runtime_set_active(dev);
-	pm_runtime_enable(dev);
+	ret = devm_pm_runtime_enable(dev);
+	if (ret)
+		return ret;
 	/*
 	 * Prevent runtime pm from being ON by default. Users can enable
 	 * it using power/control in sysfs.
@@ -5756,6 +5795,9 @@
 			goto err_node_put;
 		}
 
+		if (cfg->type != PHY_TYPE_DP)
+			qmp->usb_phy = qmp->phys[id];
+
 		/*
 		 * Register the pipe clock provided by phy.
 		 * See function description to see details of this pipe clock.
@@ -5778,16 +5820,16 @@
 		id++;
 	}
 
+	if (!qmp->usb_phy)
+		return -EINVAL;
+
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 	if (!IS_ERR(phy_provider))
 		dev_info(dev, "Registered Qcom-QMP phy\n");
-	else
-		pm_runtime_disable(dev);
 
 	return PTR_ERR_OR_ZERO(phy_provider);
 
 err_node_put:
-	pm_runtime_disable(dev);
 	of_node_put(child);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -561,7 +561,7 @@
 {
 	struct device *dev = &qphy->phy->dev;
 	const struct qusb2_phy_cfg *cfg = qphy->cfg;
-	u8 *val;
+	u8 *val, hstx_trim;
 
 	/* efuse register is optional */
 	if (!qphy->cell)
@@ -575,7 +575,13 @@
 	 * set while configuring the phy.
 	 */
 	val = nvmem_cell_read(qphy->cell, NULL);
-	if (IS_ERR(val) || !val[0]) {
+	if (IS_ERR(val)) {
+		dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
+		return;
+	}
+	hstx_trim = val[0];
+	kfree(val);
+	if (!hstx_trim) {
 		dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
 		return;
 	}
@@ -583,12 +589,10 @@
 	/* Fused TUNE1/2 value is the higher nibble only */
 	if (cfg->update_tune1_with_efuse)
 		qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
-				 val[0] << HSTX_TRIM_SHIFT,
-				 HSTX_TRIM_MASK);
+				 hstx_trim << HSTX_TRIM_SHIFT, HSTX_TRIM_MASK);
 	else
 		qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2],
-				 val[0] << HSTX_TRIM_SHIFT,
-				 HSTX_TRIM_MASK);
+				 hstx_trim << HSTX_TRIM_SHIFT, HSTX_TRIM_MASK);
 }
 
 static int qusb2_phy_set_mode(struct phy *phy,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
@@ -33,7 +33,7 @@
 
 #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
 #define RETENABLEN				BIT(3)
-#define FSEL_MASK				GENMASK(7, 5)
+#define FSEL_MASK				GENMASK(6, 4)
 #define FSEL_DEFAULT				(0x3 << 4)
 
 #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1	(0x58)
@@ -68,23 +68,27 @@
 /**
  * struct qcom_snps_hsphy - snps hs phy attributes
  *
+ * @dev: device structure
+ *
  * @phy: generic phy
  * @base: iomapped memory space for snps hs phy
  *
- * @cfg_ahb_clk: AHB2PHY interface clock
- * @ref_clk: phy reference clock
- * @iface_clk: phy interface clock
+ * @num_clks: number of clocks
+ * @clks: array of clocks
  * @phy_reset: phy reset control
  * @vregs: regulator supplies bulk data
  * @phy_initialized: if PHY has been initialized correctly
  * @mode: contains the current mode the PHY is in
+ * @update_seq_cfg: tuning parameters for phy init
  */
 struct qcom_snps_hsphy {
+	struct device *dev;
+
 	struct phy *phy;
 	void __iomem *base;
 
-	struct clk *cfg_ahb_clk;
-	struct clk *ref_clk;
+	int num_clks;
+	struct clk_bulk_data *clks;
 	struct reset_control *phy_reset;
 	struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS];
 
@@ -92,6 +96,34 @@
 	enum phy_mode mode;
 };
 
+static int qcom_snps_hsphy_clk_init(struct qcom_snps_hsphy *hsphy)
+{
+	struct device *dev = hsphy->dev;
+
+	hsphy->num_clks = 2;
+	hsphy->clks = devm_kcalloc(dev, hsphy->num_clks, sizeof(*hsphy->clks), GFP_KERNEL);
+	if (!hsphy->clks)
+		return -ENOMEM;
+
+	/*
+	 * TODO: Currently no device tree instantiation of the PHY is using the clock.
+	 * This needs to be fixed in order for this code to be able to use devm_clk_bulk_get().
+	 */
+	hsphy->clks[0].id = "cfg_ahb";
+	hsphy->clks[0].clk = devm_clk_get_optional(dev, "cfg_ahb");
+	if (IS_ERR(hsphy->clks[0].clk))
+		return dev_err_probe(dev, PTR_ERR(hsphy->clks[0].clk),
+				     "failed to get cfg_ahb clk\n");
+
+	hsphy->clks[1].id = "ref";
+	hsphy->clks[1].clk = devm_clk_get(dev, "ref");
+	if (IS_ERR(hsphy->clks[1].clk))
+		return dev_err_probe(dev, PTR_ERR(hsphy->clks[1].clk),
+				     "failed to get ref clk\n");
+
+	return 0;
+}
+
 static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
 						u32 mask, u32 val)
 {
@@ -122,22 +154,13 @@
 					   0, USB2_AUTO_RESUME);
 	}
 
-	clk_disable_unprepare(hsphy->cfg_ahb_clk);
 	return 0;
 }
 
 static int qcom_snps_hsphy_resume(struct qcom_snps_hsphy *hsphy)
 {
-	int ret;
-
 	dev_dbg(&hsphy->phy->dev, "Resume QCOM SNPS PHY, mode\n");
 
-	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
-	if (ret) {
-		dev_err(&hsphy->phy->dev, "failed to enable cfg ahb clock\n");
-		return ret;
-	}
-
 	return 0;
 }
 
@@ -148,8 +171,7 @@
 	if (!hsphy->phy_initialized)
 		return 0;
 
-	qcom_snps_hsphy_suspend(hsphy);
-	return 0;
+	return qcom_snps_hsphy_suspend(hsphy);
 }
 
 static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
@@ -159,8 +181,7 @@
 	if (!hsphy->phy_initialized)
 		return 0;
 
-	qcom_snps_hsphy_resume(hsphy);
-	return 0;
+	return qcom_snps_hsphy_resume(hsphy);
 }
 
 static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
@@ -183,16 +204,16 @@
 	if (ret)
 		return ret;
 
-	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
+	ret = clk_bulk_prepare_enable(hsphy->num_clks, hsphy->clks);
 	if (ret) {
-		dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+		dev_err(&phy->dev, "failed to enable clocks, %d\n", ret);
 		goto poweroff_phy;
 	}
 
 	ret = reset_control_assert(hsphy->phy_reset);
 	if (ret) {
 		dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret);
-		goto disable_ahb_clk;
+		goto disable_clks;
 	}
 
 	usleep_range(100, 150);
@@ -200,7 +221,7 @@
 	ret = reset_control_deassert(hsphy->phy_reset);
 	if (ret) {
 		dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret);
-		goto disable_ahb_clk;
+		goto disable_clks;
 	}
 
 	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_CFG0,
@@ -246,8 +267,8 @@
 
 	return 0;
 
-disable_ahb_clk:
-	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+disable_clks:
+	clk_bulk_disable_unprepare(hsphy->num_clks, hsphy->clks);
 poweroff_phy:
 	regulator_bulk_disable(ARRAY_SIZE(hsphy->vregs), hsphy->vregs);
 
@@ -259,7 +280,7 @@
 	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
 
 	reset_control_assert(hsphy->phy_reset);
-	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+	clk_bulk_disable_unprepare(hsphy->num_clks, hsphy->clks);
 	regulator_bulk_disable(ARRAY_SIZE(hsphy->vregs), hsphy->vregs);
 	hsphy->phy_initialized = false;
 
@@ -299,17 +320,15 @@
 	if (!hsphy)
 		return -ENOMEM;
 
+	hsphy->dev = dev;
+
 	hsphy->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(hsphy->base))
 		return PTR_ERR(hsphy->base);
 
-	hsphy->ref_clk = devm_clk_get(dev, "ref");
-	if (IS_ERR(hsphy->ref_clk)) {
-		ret = PTR_ERR(hsphy->ref_clk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get ref clk, %d\n", ret);
-		return ret;
-	}
+	ret = qcom_snps_hsphy_clk_init(hsphy);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to initialize clocks\n");
 
 	hsphy->phy_reset = devm_reset_control_get_exclusive(&pdev->dev, NULL);
 	if (IS_ERR(hsphy->phy_reset)) {
@@ -322,12 +341,9 @@
 		hsphy->vregs[i].supply = qcom_snps_hsphy_vreg_names[i];
 
 	ret = devm_regulator_bulk_get(dev, num, hsphy->vregs);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get regulator supplies: %d\n",
-				ret);
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to get regulator supplies\n");
 
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/qualcomm/phy-qcom-usb-hsic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/qualcomm/phy-qcom-usb-hsic.c
@@ -54,8 +54,10 @@
 
 	/* Configure pins for HSIC functionality */
 	pins_default = pinctrl_lookup_state(uphy->pctl, PINCTRL_STATE_DEFAULT);
-	if (IS_ERR(pins_default))
-		return PTR_ERR(pins_default);
+	if (IS_ERR(pins_default)) {
+		ret = PTR_ERR(pins_default);
+		goto err_ulpi;
+	}
 
 	ret = pinctrl_select_state(uphy->pctl, pins_default);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/ralink/phy-mt7621-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/ralink/phy-mt7621-pci.c
@@ -280,7 +280,8 @@
 }
 
 static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
-	{ .soc_id = "mt7621", .revision = "E2" }
+	{ .soc_id = "mt7621", .revision = "E2" },
+	{ /* sentinel */ }
 };
 
 static const struct regmap_config mt7621_pci_phy_regmap_config = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/renesas/phy-rcar-gen3-usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/renesas/phy-rcar-gen3-usb2.c
@@ -675,8 +675,6 @@
 	channel->irq = platform_get_irq_optional(pdev, 0);
 	channel->dr_mode = rcar_gen3_get_dr_mode(dev->of_node);
 	if (channel->dr_mode != USB_DR_MODE_UNKNOWN) {
-		int ret;
-
 		channel->is_otg_channel = true;
 		channel->uses_otg_pins = !of_property_read_bool(dev->of_node,
 							"renesas,no-otg-pins");
@@ -740,8 +738,6 @@
 		ret = PTR_ERR(provider);
 		goto error;
 	} else if (channel->is_otg_channel) {
-		int ret;
-
 		ret = device_create_file(dev, &dev_attr_role);
 		if (ret < 0)
 			goto error;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c
@@ -5,6 +5,7 @@
  * Author: Wyon Bi <bivvy.bi@rock-chips.com>
  */
 
+#include <linux/bits.h>
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/iopoll.h>
@@ -364,7 +365,7 @@
 	 * The value of counter for HS Tclk-pre
 	 * Tclk-pre = Tpin_txbyteclkhs * value
 	 */
-	clk_pre = DIV_ROUND_UP(cfg->clk_pre, t_txbyteclkhs);
+	clk_pre = DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE);
 
 	/*
 	 * The value of counter for HS Tlpx Time
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
@@ -745,10 +745,12 @@
 		do_div(vco, (nd * (no_a == 1 ? no_b : no_a) * no_d * 2));
 	}
 
-	inno->pixclock = vco;
-	dev_dbg(inno->dev, "%s rate %lu\n", __func__, inno->pixclock);
+	inno->pixclock = DIV_ROUND_CLOSEST((unsigned long)vco, 1000) * 1000;
 
-	return vco;
+	dev_dbg(inno->dev, "%s rate %lu vco %llu\n",
+		__func__, inno->pixclock, vco);
+
+	return inno->pixclock;
 }
 
 static long inno_hdmi_phy_rk3328_clk_round_rate(struct clk_hw *hw,
@@ -790,8 +792,8 @@
 			 RK3328_PRE_PLL_POWER_DOWN);
 
 	/* Configure pre-pll */
-	inno_update_bits(inno, 0xa0, RK3228_PCLK_VCO_DIV_5_MASK,
-			 RK3228_PCLK_VCO_DIV_5(cfg->vco_div_5_en));
+	inno_update_bits(inno, 0xa0, RK3328_PCLK_VCO_DIV_5_MASK,
+			 RK3328_PCLK_VCO_DIV_5(cfg->vco_div_5_en));
 	inno_write(inno, 0xa1, RK3328_PRE_PLL_PRE_DIV(cfg->prediv));
 
 	val = RK3328_SPREAD_SPECTRUM_MOD_DISABLE;
@@ -1021,9 +1023,10 @@
 
 	inno_write(inno, 0xac, RK3328_POST_PLL_FB_DIV_7_0(cfg->fbdiv));
 	if (cfg->postdiv == 1) {
-		inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS);
 		inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
 			   RK3328_POST_PLL_PRE_DIV(cfg->prediv));
+		inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS |
+			   RK3328_POST_PLL_POWER_DOWN);
 	} else {
 		v = (cfg->postdiv / 2) - 1;
 		v &= RK3328_POST_PLL_POST_DIV_MASK;
@@ -1031,7 +1034,8 @@
 		inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
 			   RK3328_POST_PLL_PRE_DIV(cfg->prediv));
 		inno_write(inno, 0xaa, RK3328_POST_PLL_POST_DIV_ENABLE |
-			   RK3328_POST_PLL_REFCLK_SEL_TMDS);
+			   RK3328_POST_PLL_REFCLK_SEL_TMDS |
+			   RK3328_POST_PLL_POWER_DOWN);
 	}
 
 	for (v = 0; v < 14; v++)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -467,8 +467,10 @@
 		return ret;
 
 	ret = property_enable(base, &rport->port_cfg->phy_sus, false);
-	if (ret)
+	if (ret) {
+		clk_disable_unprepare(rphy->clk480m);
 		return ret;
+	}
 
 	/* waiting for the utmi_clk to become stable */
 	usleep_range(1500, 2000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/rockchip/phy-rockchip-typec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -808,9 +808,8 @@
 	struct extcon_dev *edev = tcphy->extcon;
 	union extcon_property_value property;
 	unsigned int id;
-	bool ufp, dp;
 	u8 mode;
-	int ret;
+	int ret, ufp, dp;
 
 	if (!edev)
 		return MODE_DFP_USB;
@@ -821,10 +820,10 @@
 	mode = MODE_DFP_USB;
 	id = EXTCON_USB_HOST;
 
-	if (ufp) {
+	if (ufp > 0) {
 		mode = MODE_UFP_USB;
 		id = EXTCON_USB;
-	} else if (dp) {
+	} else if (dp > 0) {
 		mode = MODE_DFP_DP;
 		id = EXTCON_DISP_DP;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/samsung/phy-exynos-pcie.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/samsung/phy-exynos-pcie.c
@@ -51,6 +51,13 @@
 {
 	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
 
+	regmap_update_bits(ep->pmureg, EXYNOS5433_PMU_PCIE_PHY_OFFSET,
+			   BIT(0), 1);
+	regmap_update_bits(ep->fsysreg, PCIE_EXYNOS5433_PHY_GLOBAL_RESET,
+			   PCIE_APP_REQ_EXIT_L1_MODE, 0);
+	regmap_update_bits(ep->fsysreg, PCIE_EXYNOS5433_PHY_L1SUB_CM_CON,
+			   PCIE_REFCLK_GATING_EN, 0);
+
 	regmap_update_bits(ep->fsysreg,	PCIE_EXYNOS5433_PHY_COMMON_RESET,
 			   PCIE_PHY_RESET, 1);
 	regmap_update_bits(ep->fsysreg, PCIE_EXYNOS5433_PHY_MAC_RESET,
@@ -109,20 +116,7 @@
 	return 0;
 }
 
-static int exynos5433_pcie_phy_power_on(struct phy *phy)
-{
-	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
-
-	regmap_update_bits(ep->pmureg, EXYNOS5433_PMU_PCIE_PHY_OFFSET,
-			   BIT(0), 1);
-	regmap_update_bits(ep->fsysreg, PCIE_EXYNOS5433_PHY_GLOBAL_RESET,
-			   PCIE_APP_REQ_EXIT_L1_MODE, 0);
-	regmap_update_bits(ep->fsysreg, PCIE_EXYNOS5433_PHY_L1SUB_CM_CON,
-			   PCIE_REFCLK_GATING_EN, 0);
-	return 0;
-}
-
-static int exynos5433_pcie_phy_power_off(struct phy *phy)
+static int exynos5433_pcie_phy_exit(struct phy *phy)
 {
 	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
 
@@ -135,8 +129,7 @@
 
 static const struct phy_ops exynos5433_phy_ops = {
 	.init		= exynos5433_pcie_phy_init,
-	.power_on	= exynos5433_pcie_phy_power_on,
-	.power_off	= exynos5433_pcie_phy_power_off,
+	.exit		= exynos5433_pcie_phy_exit,
 	.owner		= THIS_MODULE,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/samsung/phy-exynos5-usbdrd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/samsung/phy-exynos5-usbdrd.c
@@ -288,9 +288,9 @@
 	reg |=	PHYCLKRST_REFCLKSEL_EXT_REFCLK;
 
 	/* FSEL settings corresponding to reference clock */
-	reg &= ~PHYCLKRST_FSEL_PIPE_MASK |
-		PHYCLKRST_MPLL_MULTIPLIER_MASK |
-		PHYCLKRST_SSC_REFCLKSEL_MASK;
+	reg &= ~(PHYCLKRST_FSEL_PIPE_MASK |
+		 PHYCLKRST_MPLL_MULTIPLIER_MASK |
+		 PHYCLKRST_SSC_REFCLKSEL_MASK);
 	switch (phy_drd->extrefclk) {
 	case EXYNOS5_FSEL_50MHZ:
 		reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
@@ -332,9 +332,9 @@
 	reg &= ~PHYCLKRST_REFCLKSEL_MASK;
 	reg |=	PHYCLKRST_REFCLKSEL_EXT_REFCLK;
 
-	reg &= ~PHYCLKRST_FSEL_UTMI_MASK |
-		PHYCLKRST_MPLL_MULTIPLIER_MASK |
-		PHYCLKRST_SSC_REFCLKSEL_MASK;
+	reg &= ~(PHYCLKRST_FSEL_UTMI_MASK |
+		 PHYCLKRST_MPLL_MULTIPLIER_MASK |
+		 PHYCLKRST_SSC_REFCLKSEL_MASK);
 	reg |= PHYCLKRST_FSEL(phy_drd->extrefclk);
 
 	return reg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/samsung/phy-exynos5250-sata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/samsung/phy-exynos5250-sata.c
@@ -187,6 +187,7 @@
 		return -EINVAL;
 
 	sata_phy->client = of_find_i2c_device_by_node(node);
+	of_node_put(node);
 	if (!sata_phy->client)
 		return -EPROBE_DEFER;
 
@@ -195,20 +196,21 @@
 	sata_phy->phyclk = devm_clk_get(dev, "sata_phyctrl");
 	if (IS_ERR(sata_phy->phyclk)) {
 		dev_err(dev, "failed to get clk for PHY\n");
-		return PTR_ERR(sata_phy->phyclk);
+		ret = PTR_ERR(sata_phy->phyclk);
+		goto put_dev;
 	}
 
 	ret = clk_prepare_enable(sata_phy->phyclk);
 	if (ret < 0) {
 		dev_err(dev, "failed to enable source clk\n");
-		return ret;
+		goto put_dev;
 	}
 
 	sata_phy->phy = devm_phy_create(dev, NULL, &exynos_sata_phy_ops);
 	if (IS_ERR(sata_phy->phy)) {
-		clk_disable_unprepare(sata_phy->phyclk);
 		dev_err(dev, "failed to create PHY\n");
-		return PTR_ERR(sata_phy->phy);
+		ret = PTR_ERR(sata_phy->phy);
+		goto clk_disable;
 	}
 
 	phy_set_drvdata(sata_phy->phy, sata_phy);
@@ -216,11 +218,18 @@
 	phy_provider = devm_of_phy_provider_register(dev,
 					of_phy_simple_xlate);
 	if (IS_ERR(phy_provider)) {
-		clk_disable_unprepare(sata_phy->phyclk);
-		return PTR_ERR(phy_provider);
+		ret = PTR_ERR(phy_provider);
+		goto clk_disable;
 	}
 
 	return 0;
+
+clk_disable:
+	clk_disable_unprepare(sata_phy->phyclk);
+put_dev:
+	put_device(&sata_phy->client->dev);
+
+	return ret;
 }
 
 static const struct of_device_id exynos_sata_phy_of_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/samsung/phy-exynosautov9-ufs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/samsung/phy-exynosautov9-ufs.c
@@ -31,22 +31,22 @@
 	PHY_COMN_REG_CFG(0x023, 0xc0, PWR_MODE_ANY),
 	PHY_COMN_REG_CFG(0x023, 0x00, PWR_MODE_ANY),
 
-	PHY_TRSV_REG_CFG(0x042, 0x5d, PWR_MODE_ANY),
-	PHY_TRSV_REG_CFG(0x043, 0x80, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG_AUTOV9(0x042, 0x5d, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG_AUTOV9(0x043, 0x80, PWR_MODE_ANY),
 
 	END_UFS_PHY_CFG,
 };
 
 /* Calibration for HS mode series A/B */
 static const struct samsung_ufs_phy_cfg exynosautov9_pre_pwr_hs_cfg[] = {
-	PHY_TRSV_REG_CFG(0x032, 0xbc, PWR_MODE_HS_ANY),
-	PHY_TRSV_REG_CFG(0x03c, 0x7f, PWR_MODE_HS_ANY),
-	PHY_TRSV_REG_CFG(0x048, 0xc0, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG_AUTOV9(0x032, 0xbc, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG_AUTOV9(0x03c, 0x7f, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG_AUTOV9(0x048, 0xc0, PWR_MODE_HS_ANY),
 
-	PHY_TRSV_REG_CFG(0x04a, 0x00, PWR_MODE_HS_G3_SER_B),
-	PHY_TRSV_REG_CFG(0x04b, 0x10, PWR_MODE_HS_G1_SER_B |
-				      PWR_MODE_HS_G3_SER_B),
-	PHY_TRSV_REG_CFG(0x04d, 0x63, PWR_MODE_HS_G3_SER_B),
+	PHY_TRSV_REG_CFG_AUTOV9(0x04a, 0x00, PWR_MODE_HS_G3_SER_B),
+	PHY_TRSV_REG_CFG_AUTOV9(0x04b, 0x10, PWR_MODE_HS_G1_SER_B |
+				PWR_MODE_HS_G3_SER_B),
+	PHY_TRSV_REG_CFG_AUTOV9(0x04d, 0x63, PWR_MODE_HS_G3_SER_B),
 
 	END_UFS_PHY_CFG,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/socionext/phy-uniphier-usb3ss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/socionext/phy-uniphier-usb3ss.c
@@ -22,11 +22,13 @@
 #include <linux/reset.h>
 
 #define SSPHY_TESTI		0x0
-#define SSPHY_TESTO		0x4
 #define TESTI_DAT_MASK		GENMASK(13, 6)
 #define TESTI_ADR_MASK		GENMASK(5, 1)
 #define TESTI_WR_EN		BIT(0)
 
+#define SSPHY_TESTO		0x4
+#define TESTO_DAT_MASK		GENMASK(7, 0)
+
 #define PHY_F(regno, msb, lsb) { (regno), (msb), (lsb) }
 
 #define CDR_CPD_TRIM	PHY_F(7, 3, 0)	/* RxPLL charge pump current */
@@ -84,12 +86,12 @@
 	val  = FIELD_PREP(TESTI_DAT_MASK, 1);
 	val |= FIELD_PREP(TESTI_ADR_MASK, p->field.reg_no);
 	uniphier_u3ssphy_testio_write(priv, val);
-	val = readl(priv->base + SSPHY_TESTO);
+	val = readl(priv->base + SSPHY_TESTO) & TESTO_DAT_MASK;
 
 	/* update value */
-	val &= ~FIELD_PREP(TESTI_DAT_MASK, field_mask);
+	val &= ~field_mask;
 	data = field_mask & (p->value << p->field.lsb);
-	val  = FIELD_PREP(TESTI_DAT_MASK, data);
+	val  = FIELD_PREP(TESTI_DAT_MASK, data | val);
 	val |= FIELD_PREP(TESTI_ADR_MASK, p->field.reg_no);
 	uniphier_u3ssphy_testio_write(priv, val);
 	uniphier_u3ssphy_testio_write(priv, val | TESTI_WR_EN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/st/phy-miphy28lp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/st/phy-miphy28lp.c
@@ -9,6 +9,7 @@
 
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -484,19 +485,11 @@
 
 static inline int miphy28lp_wait_compensation(struct miphy28lp_phy *miphy_phy)
 {
-	unsigned long finish = jiffies + 5 * HZ;
 	u8 val;
 
 	/* Waiting for Compensation to complete */
-	do {
-		val = readb_relaxed(miphy_phy->base + MIPHY_COMP_FSM_6);
-
-		if (time_after_eq(jiffies, finish))
-			return -EBUSY;
-		cpu_relax();
-	} while (!(val & COMP_DONE));
-
-	return 0;
+	return readb_relaxed_poll_timeout(miphy_phy->base + MIPHY_COMP_FSM_6,
+					  val, val & COMP_DONE, 1, 5 * USEC_PER_SEC);
 }
 
 
@@ -805,7 +798,6 @@
 
 static inline int miphy_is_ready(struct miphy28lp_phy *miphy_phy)
 {
-	unsigned long finish = jiffies + 5 * HZ;
 	u8 mask = HFC_PLL | HFC_RDY;
 	u8 val;
 
@@ -816,21 +808,14 @@
 	if (miphy_phy->type == PHY_TYPE_SATA)
 		mask |= PHY_RDY;
 
-	do {
-		val = readb_relaxed(miphy_phy->base + MIPHY_STATUS_1);
-		if ((val & mask) != mask)
-			cpu_relax();
-		else
-			return 0;
-	} while (!time_after_eq(jiffies, finish));
-
-	return -EBUSY;
+	return readb_relaxed_poll_timeout(miphy_phy->base + MIPHY_STATUS_1,
+					  val, (val & mask) == mask, 1,
+					  5 * USEC_PER_SEC);
 }
 
 static int miphy_osc_is_ready(struct miphy28lp_phy *miphy_phy)
 {
 	struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
-	unsigned long finish = jiffies + 5 * HZ;
 	u32 val;
 
 	if (!miphy_phy->osc_rdy)
@@ -839,17 +824,10 @@
 	if (!miphy_phy->syscfg_reg[SYSCFG_STATUS])
 		return -EINVAL;
 
-	do {
-		regmap_read(miphy_dev->regmap,
-				miphy_phy->syscfg_reg[SYSCFG_STATUS], &val);
-
-		if ((val & MIPHY_OSC_RDY) != MIPHY_OSC_RDY)
-			cpu_relax();
-		else
-			return 0;
-	} while (!time_after_eq(jiffies, finish));
-
-	return -EBUSY;
+	return regmap_read_poll_timeout(miphy_dev->regmap,
+					miphy_phy->syscfg_reg[SYSCFG_STATUS],
+					val, val & MIPHY_OSC_RDY, 1,
+					5 * USEC_PER_SEC);
 }
 
 static int miphy28lp_get_resource_byname(struct device_node *child,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/st/phy-stm32-usbphyc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/st/phy-stm32-usbphyc.c
@@ -225,7 +225,7 @@
 
 		ret = __stm32_usbphyc_pll_disable(usbphyc);
 		if (ret)
-			return ret;
+			goto dec_n_pll_cons;
 	}
 
 	ret = stm32_usbphyc_regulators_enable(usbphyc);
@@ -279,7 +279,9 @@
 	return 0;
 
 pll_disable:
-	return stm32_usbphyc_pll_disable(usbphyc);
+	stm32_usbphyc_pll_disable(usbphyc);
+
+	return ret;
 }
 
 static int stm32_usbphyc_phy_exit(struct phy *phy)
@@ -530,6 +532,8 @@
 		ret = of_property_read_u32(child, "reg", &index);
 		if (ret || index > usbphyc->nphys) {
 			dev_err(&phy->dev, "invalid reg property: %d\n", ret);
+			if (!ret)
+				ret = -EINVAL;
 			goto put_child;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/tegra/xusb-tegra186.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/tegra/xusb-tegra186.c
@@ -897,6 +897,7 @@
 	unsigned int index = lane->index;
 	struct device *dev = padctl->dev;
 	int err;
+	u32 reg;
 
 	port = tegra_xusb_find_usb2_port(padctl, index);
 	if (!port) {
@@ -904,6 +905,16 @@
 		return -ENODEV;
 	}
 
+	if (port->mode == USB_DR_MODE_OTG ||
+	    port->mode == USB_DR_MODE_PERIPHERAL) {
+		/* reset VBUS&ID OVERRIDE */
+		reg = padctl_readl(padctl, USB2_VBUS_ID);
+		reg &= ~VBUS_OVERRIDE;
+		reg &= ~ID_OVERRIDE(~0);
+		reg |= ID_OVERRIDE_FLOATING;
+		padctl_writel(padctl, reg, USB2_VBUS_ID);
+	}
+
 	if (port->supply && port->mode == USB_DR_MODE_HOST) {
 		err = regulator_disable(port->supply);
 		if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/tegra/xusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/tegra/xusb.c
@@ -455,7 +455,7 @@
 	name = kasprintf(GFP_KERNEL, "%s-%u", type, index);
 	if (!name) {
 		of_node_put(ports);
-		return ERR_PTR(-ENOMEM);
+		return NULL;
 	}
 	np = of_get_child_by_name(ports, name);
 	kfree(name);
@@ -562,6 +562,7 @@
 		usb_role_switch_unregister(port->usb_role_sw);
 		cancel_work_sync(&port->usb_phy_work);
 		usb_remove_phy(&port->usb_phy);
+		port->usb_phy.dev->driver = NULL;
 	}
 
 	if (port->ops->remove)
@@ -668,6 +669,9 @@
 	port->dev.driver = devm_kzalloc(&port->dev,
 					sizeof(struct device_driver),
 					GFP_KERNEL);
+	if (!port->dev.driver)
+		return -ENOMEM;
+
 	port->dev.driver->owner	 = THIS_MODULE;
 
 	port->usb_role_sw = usb_role_switch_register(&port->dev,
@@ -781,6 +785,7 @@
 	usb2->base.lane = usb2->base.ops->map(&usb2->base);
 	if (IS_ERR(usb2->base.lane)) {
 		err = PTR_ERR(usb2->base.lane);
+		tegra_xusb_port_unregister(&usb2->base);
 		goto out;
 	}
 
@@ -847,6 +852,7 @@
 	ulpi->base.lane = ulpi->base.ops->map(&ulpi->base);
 	if (IS_ERR(ulpi->base.lane)) {
 		err = PTR_ERR(ulpi->base.lane);
+		tegra_xusb_port_unregister(&ulpi->base);
 		goto out;
 	}
 
@@ -1479,6 +1485,19 @@
 }
 EXPORT_SYMBOL_GPL(tegra_xusb_padctl_get_usb3_companion);
 
+int tegra_xusb_padctl_get_port_number(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane;
+
+	if (!phy)
+		return -ENODEV;
+
+	lane = phy_get_drvdata(phy);
+
+	return lane->index;
+}
+EXPORT_SYMBOL_GPL(tegra_xusb_padctl_get_port_number);
+
 MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>");
 MODULE_DESCRIPTION("Tegra XUSB Pad Controller driver");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/ti/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/ti/Kconfig
@@ -23,7 +23,7 @@
 
 config PHY_AM654_SERDES
 	tristate "TI AM654 SERDES support"
-	depends on OF && ARCH_K3 || COMPILE_TEST
+	depends on OF && (ARCH_K3 || COMPILE_TEST)
 	depends on COMMON_CLK
 	select GENERIC_PHY
 	select MULTIPLEXER
@@ -35,7 +35,7 @@
 
 config PHY_J721E_WIZ
 	tristate "TI J721E WIZ (SERDES Wrapper) support"
-	depends on OF && ARCH_K3 || COMPILE_TEST
+	depends on OF && (ARCH_K3 || COMPILE_TEST)
 	depends on HAS_IOMEM && OF_ADDRESS
 	depends on COMMON_CLK
 	select GENERIC_PHY
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/ti/phy-am654-serdes.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/ti/phy-am654-serdes.c
@@ -838,7 +838,7 @@
 
 clk_err:
 	of_clk_del_provider(node);
-
+	pm_runtime_disable(dev);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/ti/phy-gmii-sel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/ti/phy-gmii-sel.c
@@ -320,6 +320,8 @@
 		u64 size;
 
 		offset = of_get_address(dev->of_node, 0, &size, NULL);
+		if (!offset)
+			return -EINVAL;
 		priv->num_ports = size / sizeof(u32);
 		if (!priv->num_ports)
 			return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/ti/phy-j721e-wiz.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/ti/phy-j721e-wiz.c
@@ -233,6 +233,7 @@
 	{ .val = 1, .div = 2, },
 	{ .val = 2, .div = 4, },
 	{ .val = 3, .div = 8, },
+	{ /* sentinel */ },
 };
 
 static const struct wiz_clk_div_sel clk_div_sel[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/ti/phy-omap-usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/ti/phy-omap-usb2.c
@@ -116,7 +116,7 @@
 {
 	struct omap_usb *phy = phy_to_omapusb(otg->usb_phy);
 
-	if (!phy->comparator)
+	if (!phy->comparator || !phy->comparator->set_vbus)
 		return -ENODEV;
 
 	return phy->comparator->set_vbus(phy->comparator, enabled);
@@ -126,7 +126,7 @@
 {
 	struct omap_usb *phy = phy_to_omapusb(otg->usb_phy);
 
-	if (!phy->comparator)
+	if (!phy->comparator || !phy->comparator->start_srp)
 		return -ENODEV;
 
 	return phy->comparator->start_srp(phy->comparator);
@@ -215,7 +215,7 @@
 	return 0;
 
 err1:
-	clk_disable(phy->wkupclk);
+	clk_disable_unprepare(phy->wkupclk);
 
 err0:
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/Kconfig
@@ -11,3 +11,21 @@
 	help
 	  Enable this to support ZynqMP High Speed Gigabit Transceiver
 	  that is part of ZynqMP SoC.
+
+config PHY_XILINX_HDMIPHY
+       tristate "Xilinx HDMI PHY driver"
+       depends on ARCH_ZYNQMP
+       select GENERIC_PHY
+       help
+         Enable this to support HDMI PHY Controller core in FPGA.It is designed
+         for enabling plug-and-play connectivity with xilinx HDMI 2.1
+         technology MAC transmit or receive subsystem.
+
+config PHY_XILINX_DPGTQUAD
+	tristate "Xilinx GT Quad Base PHY driver for Displayport TX and RX"
+	depends on (VIDEO_XILINX_DPRXSS || DRM_XLNX_DPTX)
+	select GENERIC_PHY
+	help
+	  Enable this to support DP GT QUAD PHY controller core in FPGA.
+	  It is designed for enabling gt quad base configuration for Xilinx
+	  Displayport Tx and Rx subsystems.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/Makefile
@@ -1,3 +1,10 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_PHY_XILINX_ZYNQMP)		+= phy-zynqmp.o
+obj-$(CONFIG_PHY_XILINX_HDMIPHY)       += xilinx-hdmiphy.o
+xilinx-hdmiphy-objs := xhdmiphy.o
+xilinx-hdmiphy-objs += xhdmiphy_core.o
+xilinx-hdmiphy-objs += xhdmiphy_modules.o
+xilinx-hdmiphy-objs += xhdmiphy_gt_helper.o
+xilinx-hdmiphy-objs += xhdmiphy_mmcm.o
+obj-$(CONFIG_PHY_XILINX_DPGTQUAD)	+= xilinx_dpgtquadphy.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/phy-zynqmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/phy-zynqmp.c
@@ -21,6 +21,7 @@
 #include <linux/of.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 
 #include <dt-bindings/phy/phy.h>
@@ -80,7 +81,8 @@
 
 /* Reference clock selection parameters */
 #define L0_Ln_REF_CLK_SEL(n)		(0x2860 + (n) * 4)
-#define L0_REF_CLK_SEL_MASK		0x8f
+#define L0_REF_CLK_LCL_SEL		BIT(7)
+#define L0_REF_CLK_SEL_MASK		0x9f
 
 /* Calibration digital logic parameters */
 #define L3_TM_CALIB_DIG19		0xec4c
@@ -134,7 +136,8 @@
 #define PROT_BUS_WIDTH_10		0x0
 #define PROT_BUS_WIDTH_20		0x1
 #define PROT_BUS_WIDTH_40		0x2
-#define PROT_BUS_WIDTH_SHIFT		2
+#define PROT_BUS_WIDTH_SHIFT(n)		((n) * 2)
+#define PROT_BUS_WIDTH_MASK(n)		GENMASK((n) * 2 + 1, (n) * 2)
 
 /* Number of GT lanes */
 #define NUM_LANES			4
@@ -164,6 +167,24 @@
 /* Timeout values */
 #define TIMEOUT_US			1000
 
+/* Lane 0/1/2/3 offset */
+#define DIG_8(n)		((0x4000 * (n)) + 0x1074)
+#define ILL13(n)		((0x4000 * (n)) + 0x1994)
+#define DIG_10(n)		((0x4000 * (n)) + 0x107c)
+#define RST_DLY(n)		((0x4000 * (n)) + 0x19a4)
+#define BYP_15(n)		((0x4000 * (n)) + 0x1038)
+#define BYP_12(n)		((0x4000 * (n)) + 0x102c)
+#define MISC3(n)		((0x4000 * (n)) + 0x19ac)
+#define EQ11(n)			((0x4000 * (n)) + 0x1978)
+
+static u32 save_reg_address[] = {
+	/* Lane 0/1/2/3 Register */
+	DIG_8(0), ILL13(0), DIG_10(0), RST_DLY(0), BYP_15(0), BYP_12(0), MISC3(0), EQ11(0),
+	DIG_8(1), ILL13(1), DIG_10(1), RST_DLY(1), BYP_15(1), BYP_12(1), MISC3(1), EQ11(1),
+	DIG_8(2), ILL13(2), DIG_10(2), RST_DLY(2), BYP_15(2), BYP_12(2), MISC3(2), EQ11(2),
+	DIG_8(3), ILL13(3), DIG_10(3), RST_DLY(3), BYP_15(3), BYP_12(3), MISC3(3), EQ11(3),
+};
+
 struct xpsgtr_dev;
 
 /**
@@ -212,6 +233,7 @@
  * @tx_term_fix: fix for GT issue
  * @saved_icm_cfg0: stored value of ICM CFG0 register
  * @saved_icm_cfg1: stored value of ICM CFG1 register
+ * @saved_regs: registers to be saved/restored during suspend/resume
  */
 struct xpsgtr_dev {
 	struct device *dev;
@@ -224,6 +246,7 @@
 	bool tx_term_fix;
 	unsigned int saved_icm_cfg0;
 	unsigned int saved_icm_cfg1;
+	u32 *saved_regs;
 };
 
 /*
@@ -297,6 +320,32 @@
 	writel((readl(addr) & ~clr) | set, addr);
 }
 
+/**
+ * xpsgtr_save_lane_regs - Saves registers on suspend
+ * @gtr_dev: pointer to phy controller context structure
+ */
+static void xpsgtr_save_lane_regs(struct xpsgtr_dev *gtr_dev)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(save_reg_address); i++)
+		gtr_dev->saved_regs[i] = xpsgtr_read(gtr_dev,
+						     save_reg_address[i]);
+}
+
+/**
+ * xpsgtr_restore_lane_regs - Restores registers on resume
+ * @gtr_dev: pointer to phy controller context structure
+ */
+static void xpsgtr_restore_lane_regs(struct xpsgtr_dev *gtr_dev)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(save_reg_address); i++)
+		xpsgtr_write(gtr_dev, save_reg_address[i],
+			     gtr_dev->saved_regs[i]);
+}
+
 /*
  * Hardware Configuration
  */
@@ -348,11 +397,12 @@
 		       PLL_FREQ_MASK, ssc->pll_ref_clk);
 
 	/* Enable lane clock sharing, if required */
-	if (gtr_phy->refclk != gtr_phy->lane) {
-		/* Lane3 Ref Clock Selection Register */
+	if (gtr_phy->refclk == gtr_phy->lane)
+		xpsgtr_clr_set(gtr_phy->dev, L0_Ln_REF_CLK_SEL(gtr_phy->lane),
+			       L0_REF_CLK_SEL_MASK, L0_REF_CLK_LCL_SEL);
+	else
 		xpsgtr_clr_set(gtr_phy->dev, L0_Ln_REF_CLK_SEL(gtr_phy->lane),
 			       L0_REF_CLK_SEL_MASK, 1 << gtr_phy->refclk);
-	}
 
 	/* SSC step size [7:0] */
 	xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEP_SIZE_0_LSB,
@@ -445,12 +495,12 @@
 static void xpsgtr_phy_init_sgmii(struct xpsgtr_phy *gtr_phy)
 {
 	struct xpsgtr_dev *gtr_dev = gtr_phy->dev;
+	u32 mask = PROT_BUS_WIDTH_MASK(gtr_phy->lane);
+	u32 val = PROT_BUS_WIDTH_10 << PROT_BUS_WIDTH_SHIFT(gtr_phy->lane);
 
 	/* Set SGMII protocol TX and RX bus width to 10 bits. */
-	xpsgtr_write(gtr_dev, TX_PROT_BUS_WIDTH,
-		     PROT_BUS_WIDTH_10 << (gtr_phy->lane * PROT_BUS_WIDTH_SHIFT));
-	xpsgtr_write(gtr_dev, RX_PROT_BUS_WIDTH,
-		     PROT_BUS_WIDTH_10 << (gtr_phy->lane * PROT_BUS_WIDTH_SHIFT));
+	xpsgtr_clr_set(gtr_dev, TX_PROT_BUS_WIDTH, mask, val);
+	xpsgtr_clr_set(gtr_dev, RX_PROT_BUS_WIDTH, mask, val);
 
 	xpsgtr_bypass_scrambler_8b10b(gtr_phy);
 }
@@ -571,6 +621,10 @@
 
 	mutex_lock(&gtr_dev->gtr_mutex);
 
+	/* Configure and enable the clock when peripheral phy_init call */
+	if (clk_prepare_enable(gtr_dev->clk[gtr_phy->refclk]))
+		goto out;
+
 	/* Skip initialization if not required. */
 	if (!xpsgtr_phy_init_required(gtr_phy))
 		goto out;
@@ -615,9 +669,13 @@
 static int xpsgtr_phy_exit(struct phy *phy)
 {
 	struct xpsgtr_phy *gtr_phy = phy_get_drvdata(phy);
+	struct xpsgtr_dev *gtr_dev = gtr_phy->dev;
 
 	gtr_phy->skip_phy_init = false;
 
+	/* Ensure that disable clock only, which configure for lane */
+	clk_disable_unprepare(gtr_dev->clk[gtr_phy->refclk]);
+
 	return 0;
 }
 
@@ -820,34 +878,27 @@
  * Power Management
  */
 
-static int __maybe_unused xpsgtr_suspend(struct device *dev)
+static int xpsgtr_runtime_suspend(struct device *dev)
 {
 	struct xpsgtr_dev *gtr_dev = dev_get_drvdata(dev);
-	unsigned int i;
 
 	/* Save the snapshot ICM_CFG registers. */
 	gtr_dev->saved_icm_cfg0 = xpsgtr_read(gtr_dev, ICM_CFG0);
 	gtr_dev->saved_icm_cfg1 = xpsgtr_read(gtr_dev, ICM_CFG1);
 
-	for (i = 0; i < ARRAY_SIZE(gtr_dev->clk); i++)
-		clk_disable_unprepare(gtr_dev->clk[i]);
+	xpsgtr_save_lane_regs(gtr_dev);
 
 	return 0;
 }
 
-static int __maybe_unused xpsgtr_resume(struct device *dev)
+static int xpsgtr_runtime_resume(struct device *dev)
 {
 	struct xpsgtr_dev *gtr_dev = dev_get_drvdata(dev);
 	unsigned int icm_cfg0, icm_cfg1;
 	unsigned int i;
 	bool skip_phy_init;
-	int err;
 
-	for (i = 0; i < ARRAY_SIZE(gtr_dev->clk); i++) {
-		err = clk_prepare_enable(gtr_dev->clk[i]);
-		if (err)
-			goto err_clk_put;
-	}
+	xpsgtr_restore_lane_regs(gtr_dev);
 
 	icm_cfg0 = xpsgtr_read(gtr_dev, ICM_CFG0);
 	icm_cfg1 = xpsgtr_read(gtr_dev, ICM_CFG1);
@@ -868,18 +919,10 @@
 		gtr_dev->phys[i].skip_phy_init = skip_phy_init;
 
 	return 0;
-
-err_clk_put:
-	while (i--)
-		clk_disable_unprepare(gtr_dev->clk[i]);
-
-	return err;
 }
 
-static const struct dev_pm_ops xpsgtr_pm_ops = {
-	SET_SYSTEM_SLEEP_PM_OPS(xpsgtr_suspend, xpsgtr_resume)
-};
-
+static DEFINE_RUNTIME_DEV_PM_OPS(xpsgtr_pm_ops, xpsgtr_runtime_suspend,
+				 xpsgtr_runtime_resume, NULL);
 /*
  * Probe & Platform Driver
  */
@@ -887,7 +930,6 @@
 static int xpsgtr_get_ref_clocks(struct xpsgtr_dev *gtr_dev)
 {
 	unsigned int refclk;
-	int ret;
 
 	for (refclk = 0; refclk < ARRAY_SIZE(gtr_dev->refclk_sscs); ++refclk) {
 		unsigned long rate;
@@ -898,19 +940,14 @@
 		snprintf(name, sizeof(name), "ref%u", refclk);
 		clk = devm_clk_get_optional(gtr_dev->dev, name);
 		if (IS_ERR(clk)) {
-			ret = dev_err_probe(gtr_dev->dev, PTR_ERR(clk),
-					    "Failed to get reference clock %u\n",
-					    refclk);
-			goto err_clk_put;
+			return dev_err_probe(gtr_dev->dev, PTR_ERR(clk),
+					     "Failed to get ref clock %u\n",
+					     refclk);
 		}
 
 		if (!clk)
 			continue;
 
-		ret = clk_prepare_enable(clk);
-		if (ret)
-			goto err_clk_put;
-
 		gtr_dev->clk[refclk] = clk;
 
 		/*
@@ -930,18 +967,11 @@
 			dev_err(gtr_dev->dev,
 				"Invalid rate %lu for reference clock %u\n",
 				rate, refclk);
-			ret = -EINVAL;
-			goto err_clk_put;
+			return -EINVAL;
 		}
 	}
 
 	return 0;
-
-err_clk_put:
-	while (refclk--)
-		clk_disable_unprepare(gtr_dev->clk[refclk]);
-
-	return ret;
 }
 
 static int xpsgtr_probe(struct platform_device *pdev)
@@ -950,7 +980,6 @@
 	struct xpsgtr_dev *gtr_dev;
 	struct phy_provider *provider;
 	unsigned int port;
-	unsigned int i;
 	int ret;
 
 	gtr_dev = devm_kzalloc(&pdev->dev, sizeof(*gtr_dev), GFP_KERNEL);
@@ -990,8 +1019,7 @@
 		phy = devm_phy_create(&pdev->dev, np, &xpsgtr_phyops);
 		if (IS_ERR(phy)) {
 			dev_err(&pdev->dev, "failed to create PHY\n");
-			ret = PTR_ERR(phy);
-			goto err_clk_put;
+			return PTR_ERR(phy);
 		}
 
 		gtr_phy->phy = phy;
@@ -1002,16 +1030,36 @@
 	provider = devm_of_phy_provider_register(&pdev->dev, xpsgtr_xlate);
 	if (IS_ERR(provider)) {
 		dev_err(&pdev->dev, "registering provider failed\n");
-		ret = PTR_ERR(provider);
-		goto err_clk_put;
+		return PTR_ERR(provider);
 	}
+
+	pm_runtime_set_active(gtr_dev->dev);
+	pm_runtime_enable(gtr_dev->dev);
+
+	ret = pm_runtime_resume_and_get(gtr_dev->dev);
+	if (ret < 0) {
+		pm_runtime_disable(gtr_dev->dev);
+		return ret;
+	}
+
+	gtr_dev->saved_regs = devm_kmalloc(gtr_dev->dev,
+					   sizeof(save_reg_address),
+					   GFP_KERNEL);
+	if (!gtr_dev->saved_regs)
+		return -ENOMEM;
+
 	return 0;
+}
 
-err_clk_put:
-	for (i = 0; i < ARRAY_SIZE(gtr_dev->clk); i++)
-		clk_disable_unprepare(gtr_dev->clk[i]);
+static int xpsgtr_remove(struct platform_device *pdev)
+{
+	struct xpsgtr_dev *gtr_dev = platform_get_drvdata(pdev);
 
-	return ret;
+	pm_runtime_disable(gtr_dev->dev);
+	pm_runtime_put_noidle(gtr_dev->dev);
+	pm_runtime_set_suspended(gtr_dev->dev);
+
+	return 0;
 }
 
 static const struct of_device_id xpsgtr_of_match[] = {
@@ -1023,10 +1071,11 @@
 
 static struct platform_driver xpsgtr_driver = {
 	.probe = xpsgtr_probe,
+	.remove	= xpsgtr_remove,
 	.driver = {
 		.name = "xilinx-psgtr",
 		.of_match_table	= xpsgtr_of_match,
-		.pm =  &xpsgtr_pm_ops,
+		.pm =  pm_ptr(&xpsgtr_pm_ops),
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xhdmiphy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xhdmiphy.c
@@ -0,0 +1,837 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx HDMI PHY
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ *
+ * Author: Rajesh Gugulothu <gugulothu.rajesh@xilinx.com>
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/of_device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-hdmi.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include "xhdmiphy.h"
+
+struct xhdmiphy_lane {
+	struct phy *phy;
+	u32 share_laneclk;
+	u8 direction;
+	u8 lane;
+	void *data;
+};
+
+static int xhdmiphy_init(struct phy *phy)
+{
+	struct xhdmiphy_lane *phy_lane = phy_get_drvdata(phy);
+	struct xhdmiphy_dev *phy_dev = phy_lane->data;
+	unsigned int ret;
+	static int count;
+
+	count++;
+
+	if (count < XHDMIPHY_MAX_LANES)
+		return 0;
+
+	/* initialize HDMI phy */
+	ret = xhdmiphy_init_phy(phy_dev);
+	if (ret != 0) {
+		dev_err(phy_dev->dev, "HDMI PHY initialization error\n");
+		return -ENODEV;
+	}
+	count = 0;
+
+	return 0;
+}
+
+static int xhdmiphy_reset(struct phy *phy)
+{
+	struct xhdmiphy_lane *phy_lane = phy_get_drvdata(phy);
+	struct xhdmiphy_dev *phy_dev = phy_lane->data;
+
+	if (!phy_lane->direction)
+		xhdmiphy_ibufds_en(phy_dev, XHDMIPHY_DIR_TX, false);
+
+	return 0;
+}
+
+static bool xhdmiphy_clk_srcsel(struct xhdmiphy_dev *priv, u8 dir, u8 clksrc)
+{
+	if (priv->data && !priv->data->sel_mux(dir, clksrc))
+		return 0;
+
+	dev_dbg(priv->dev, "failed to select clock source\n");
+
+	return -EIO;
+}
+
+static bool xhdmiphy_set_lrate(struct xhdmiphy_dev *priv, u8 dir, u8 mode,
+			       u64 lrate)
+{
+	if (priv->data && !priv->data->set_linerate(dir, mode, lrate))
+		return 0;
+
+	dev_dbg(priv->dev, "failed to set linerate\n");
+
+	return -EIO;
+}
+
+static int xhdmiphy_configure(struct phy *phy, union phy_configure_opts *opts)
+{
+	struct xhdmiphy_lane *phy_lane = phy_get_drvdata(phy);
+	struct xhdmiphy_dev *phy_dev = phy_lane->data;
+	struct phy_configure_opts_hdmi *cfg = &opts->hdmi;
+	struct hdmiphy_callback *cb_ptr = &cfg->hdmiphycb;
+	unsigned int ret = 0;
+	static int count_tx, count_rx;
+
+	if (!phy_lane->direction) {
+		count_rx++;
+		if (count_rx < XHDMIPHY_MAX_LANES) {
+			return 0;
+		} else if (cfg->ibufds) {
+			xhdmiphy_ibufds_en(phy_dev, XHDMIPHY_DIR_RX,
+					   cfg->ibufds_en);
+		} else if (cfg->tmdsclock_ratio_flag) {
+			/* update TMDS clock ratio */
+			phy_dev->rx_tmdsclock_ratio = cfg->tmdsclock_ratio;
+		} else if (cfg->phycb) {
+			switch (cb_ptr->type) {
+			case RX_INIT_CB:
+				phy_dev->phycb[RX_INIT_CB].cb =
+							cfg->hdmiphycb.cb;
+				phy_dev->phycb[RX_INIT_CB].data =
+							cfg->hdmiphycb.data;
+				break;
+			case RX_READY_CB:
+				phy_dev->phycb[RX_READY_CB].cb =
+							cfg->hdmiphycb.cb;
+				phy_dev->phycb[RX_READY_CB].data =
+							cfg->hdmiphycb.data;
+				break;
+			default:
+				dev_info(phy_dev->dev,
+					 "type - %d phy callback does't match\n\r",
+					 cb_ptr->type);
+				break;
+			}
+		} else if (cfg->cal_mmcm_param) {
+			ret = xhdmiphy_cal_mmcm_param(phy_dev,
+						      XHDMIPHY_CHID_CH1,
+						      XHDMIPHY_DIR_RX, cfg->ppc,
+						      cfg->bpc);
+			if (ret)
+				dev_err(phy_dev->dev,
+					"failed to update mmcm params\n\r");
+
+			xhdmiphy_mmcm_start(phy_dev, XHDMIPHY_DIR_RX);
+		} else if (cfg->clkout1_obuftds) {
+			xhdmiphy_clkout1_obuftds_en(phy_dev, XHDMIPHY_DIR_RX,
+						    cfg->clkout1_obuftds_en);
+			cfg->clkout1_obuftds_en = 0;
+		} else if (cfg->config_hdmi20 && !cfg->config_hdmi21) {
+			/* set Rx ch4 as clock */
+			gpiod_set_value(phy_dev->rxch4_gpio, 0);
+			xhdmiphy_hdmi20_conf(phy_dev, XHDMIPHY_DIR_RX);
+			xhdmiphy_clk_srcsel(phy_dev, phy_lane->direction,
+					    tmds_mode);
+			xhdmiphy_set_lrate(phy_dev, phy_lane->direction, 0,
+					   cfg->rx_refclk_hz);
+		} else if (!cfg->config_hdmi20 && cfg->config_hdmi21) {
+			/*
+			 * Phy needs to switch between rxch4 as data or
+			 * clk based on FRL or TMDS mode. Note we can have TMDS
+			 * mode in HDMI2.1
+			 */
+			gpiod_set_value(phy_dev->rxch4_gpio, 1);
+			if (phy_dev->conf.rx_refclk_sel !=
+			    phy_dev->conf.rx_frl_refclk_sel) {
+				xhdmiphy_ibufds_en(phy_dev, XHDMIPHY_DIR_RX, 1);
+			}
+
+			xhdmiphy_hdmi21_conf(phy_dev, XHDMIPHY_DIR_RX,
+					     cfg->linerate, cfg->nchannels);
+			xhdmiphy_clk_srcsel(phy_dev, phy_lane->direction,
+					    frl_mode);
+			xhdmiphy_clkdet_freq_reset(phy_dev, XHDMIPHY_DIR_RX);
+			xhdmiphy_set_lrate(phy_dev, phy_lane->direction, 1,
+					   cfg->rx_refclk_hz);
+		} else if (cfg->rx_get_refclk) {
+			cfg->rx_refclk_hz = phy_dev->rx_refclk_hz;
+		} else if (cfg->reset_gt) {
+			xhdmiphy_rst_gt_txrx(phy_dev, XHDMIPHY_CHID_CHA,
+					     XHDMIPHY_DIR_RX, false);
+		}
+		count_rx = 0;
+	}
+
+	if (phy_lane->direction) {
+		count_tx++;
+
+		if (count_tx < XHDMIPHY_MAX_LANES) {
+			return 0;
+		} else if (cfg->ibufds) {
+			xhdmiphy_ibufds_en(phy_dev, XHDMIPHY_DIR_TX,
+					   cfg->ibufds_en);
+			cfg->ibufds = 0;
+		} else if (cfg->clkout1_obuftds) {
+			xhdmiphy_clkout1_obuftds_en(phy_dev, XHDMIPHY_DIR_TX,
+						    cfg->clkout1_obuftds_en);
+			cfg->clkout1_obuftds_en = 0;
+		} else if (cfg->tx_params) {
+			xhdmiphy_clk_srcsel(phy_dev, phy_lane->direction,
+					    tmds_mode);
+			usleep_range(1000, 1100);
+			phy_dev->tx_refclk_hz = cfg->tx_tmdsclk;
+
+			clk_set_rate(phy_dev->tmds_clk, phy_dev->tx_refclk_hz);
+			ret = xhdmiphy_set_tx_param(phy_dev,
+						    XHDMIPHY_CHID_CHA,
+						    cfg->ppc, cfg->bpc,
+						    cfg->fmt);
+			if (ret)
+				dev_err(phy_dev->dev,
+					"unable to set requested tx resolutions\n\r");
+			cfg->tx_params = 0;
+			dev_info(phy_dev->dev,
+				 "tx_tmdsclk %lld\n", cfg->tx_tmdsclk);
+			xhdmiphy_set_lrate(phy_dev, phy_lane->direction, 0,
+					   cfg->tx_tmdsclk);
+		} else if (cfg->config_hdmi21) {
+			xhdmiphy_clk_srcsel(phy_dev, phy_lane->direction,
+					    frl_mode);
+			usleep_range(1000, 1100);
+			xhdmiphy_set_lrate(phy_dev, phy_lane->direction, 1,
+					   cfg->tx_tmdsclk);
+			gpiod_set_value(phy_dev->rxch4_gpio, 1);
+			xhdmiphy_hdmi21_conf(phy_dev, XHDMIPHY_DIR_TX,
+					     cfg->linerate, cfg->nchannels);
+			xhdmiphy_clkdet_freq_reset(phy_dev, XHDMIPHY_DIR_TX);
+			cfg->config_hdmi21 = 0;
+		}
+		count_tx = 0;
+	}
+
+	return 0;
+}
+
+static const struct phy_ops xhdmiphy_phyops = {
+	.configure	= xhdmiphy_configure,
+	.reset		= xhdmiphy_reset,
+	.init		= xhdmiphy_init,
+	.owner		= THIS_MODULE,
+};
+
+static struct phy *xhdmiphy_xlate(struct device *dev,
+				  struct of_phandle_args *args)
+{
+	struct xhdmiphy_dev *priv = dev_get_drvdata(dev);
+	struct xhdmiphy_lane *hdmiphy_lane = NULL;
+	struct device_node *hdmiphynode = args->np;
+	int index;
+
+	if (args->args_count != 4) {
+		dev_err(dev, "Invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (!of_device_is_available(hdmiphynode)) {
+		dev_warn(dev, "requested PHY is disabled\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	for (index = 0; index < of_get_child_count(dev->of_node); index++) {
+		if (hdmiphynode == priv->lanes[index]->phy->dev.of_node) {
+			hdmiphy_lane = priv->lanes[index];
+			break;
+		}
+	}
+
+	if (!hdmiphy_lane) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	hdmiphy_lane->share_laneclk = args->args[2];
+	hdmiphy_lane->direction = args->args[3];
+
+	return hdmiphy_lane->phy;
+}
+
+static irqreturn_t xhdmiphy_irq_handler(int irq, void *dev_id)
+{
+	struct xhdmiphy_dev *priv;
+
+	priv = (struct xhdmiphy_dev *)dev_id;
+	if (!priv)
+		return IRQ_NONE;
+
+	/*
+	 * disable interrupts in the HDMI PHY, they are re-enabled once
+	 * serviced
+	 */
+	xhdmiphy_intr_dis(priv, XHDMIPHY_INTR_ALL_MASK);
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t xhdmiphy_irq_thread(int irq, void *dev_id)
+{
+	struct xhdmiphy_dev *priv;
+	u32 status;
+	u32 event_mask;
+	u32 event_ack;
+
+	priv = (struct xhdmiphy_dev *)dev_id;
+	if (!priv)
+		return IRQ_NONE;
+
+	/* call baremetal interrupt handler with mutex locked */
+	mutex_lock(&priv->hdmiphy_mutex);
+
+	status = xhdmiphy_read(priv, XHDMIPHY_INTR_STS_REG);
+	dev_dbg(priv->dev, "xhdmiphy status = %x\n", status);
+
+	if (priv->conf.gt_type != XHDMIPHY_GTYE5) {
+		event_mask = XHDMIPHY_INTR_QPLL0_LOCK_MASK |
+			     XHDMIPHY_INTR_CPLL_LOCK_MASK |
+			     XHDMIPHY_INTR_QPLL1_LOCK_MASK |
+			     XHDMIPHY_INTR_TXALIGNDONE_MASK |
+			     XHDMIPHY_INTR_TXRESETDONE_MASK |
+			     XHDMIPHY_INTR_RXRESETDONE_MASK |
+			     XHDMIPHY_INTR_TXMMCMUSRCLK_LOCK_MASK |
+			     XHDMIPHY_INTR_RXMMCMUSRCLK_LOCK_MASK;
+	} else {
+		event_mask = XHDMIPHY_INTR_LCPLL_LOCK_MASK |
+			     XHDMIPHY_INTR_RPLL_LOCK_MASK |
+			     XHDMIPHY_INTR_TXGPO_RE_MASK |
+			     XHDMIPHY_INTR_RXGPO_RE_MASK |
+			     XHDMIPHY_INTR_TXRESETDONE_MASK |
+			     XHDMIPHY_INTR_RXRESETDONE_MASK |
+			     XHDMIPHY_INTR_TXMMCMUSRCLK_LOCK_MASK |
+			     XHDMIPHY_INTR_RXMMCMUSRCLK_LOCK_MASK;
+	}
+
+	event_ack = event_mask & status;
+	if (event_ack)
+		xhdmiphy_gt_handler(priv, event_ack, status);
+
+	event_mask = XHDMIPHY_INTR_TXFREQCHANGE_MASK |
+		     XHDMIPHY_INTR_RXFREQCHANGE_MASK |
+		     XHDMIPHY_INTR_TXTMRTIMEOUT_MASK |
+		     XHDMIPHY_INTR_RXTMRTIMEOUT_MASK;
+
+	event_ack = event_mask & status;
+	if (event_ack)
+		xhdmiphy_clkdet_handler(priv, event_ack, status);
+
+	mutex_unlock(&priv->hdmiphy_mutex);
+
+	/* enable interrupt requesting in the PHY */
+	xhdmiphy_intr_en(priv, XHDMIPHY_INTR_ALL_MASK);
+
+	return IRQ_HANDLED;
+}
+
+static int xhdmiphy_parse_of(struct xhdmiphy_dev *priv)
+{
+	struct xhdmiphy_conf *xgtphycfg = &priv->conf;
+	struct device *dev = priv->dev;
+	struct device_node *node = dev->of_node;
+	int rc, val;
+
+	rc = of_property_read_u32(node, "xlnx,transceiver-type", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,transceiver-type");
+		return rc;
+	}
+
+	if (val != XHDMIPHY_GTHE4 && val != XHDMIPHY_GTYE4 &&
+	    val != XHDMIPHY_GTYE5) {
+		dev_err(priv->dev, "dt transceiver-type %d is invalid\n", val);
+		return -EINVAL;
+	}
+	xgtphycfg->gt_type = val;
+
+	rc = of_property_read_u32(node, "xlnx,input-pixels-per-clock", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,input-pixels-per-clock");
+		return rc;
+	}
+
+	if (val != 4 && val != 8) {
+		dev_err(priv->dev, "dt input-pixels-per-clock %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->ppc = val;
+
+	rc = of_property_read_u32(node, "xlnx,nidru", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,nidru");
+		return rc;
+	}
+
+	if (val != 0 && val != 1) {
+		dev_err(priv->dev, "dt nidru %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->dru_present = val;
+
+	rc = of_property_read_u32(node, "xlnx,nidru-refclk-sel", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,nidru-refclk-sel");
+		return rc;
+	}
+
+	if (val < XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0 - 1 &&
+	    val > XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK - 1) {
+		dev_err(priv->dev, "dt nidru-refclk-sel %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->dru_refclk_sel = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-no-of-channels", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,rx-no-of-channels");
+		return rc;
+	}
+
+	if (val != 1 && val != 2 && val != 4) {
+		dev_err(priv->dev, "dt rx-no-of-channels %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->rx_channels = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-no-of-channels", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,tx-no-of-channels");
+		return rc;
+	}
+
+	if (val != 1 && val != 2 && val != 4) {
+		dev_err(priv->dev, "dt tx-no-of-channels %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->tx_channels = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-protocol", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,rx-protocol");
+		return rc;
+	}
+
+	if (val != XHDMIPHY_PROT_HDMI && val != XHDMIPHY_PROT_HDMI21 &&
+	    val != XHDMIPHY_PROT_NONE) {
+		dev_err(priv->dev, "dt rx-protocol %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->rx_protocol = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-protocol", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,tx-protocol");
+		return rc;
+	}
+
+	if (val != XHDMIPHY_PROT_HDMI && val != XHDMIPHY_PROT_HDMI21 &&
+	    val != XHDMIPHY_PROT_NONE) {
+		dev_err(priv->dev, "dt tx-protocol %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->tx_protocol = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-refclk-sel", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,rx-refclk-sel");
+		return rc;
+	}
+
+	if (val < XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0 - 1 &&
+	    val > XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK - 1) {
+		dev_err(priv->dev, "dt rx-refclk-sel %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->rx_refclk_sel = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-refclk-sel", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,tx-refclk-sel");
+		return rc;
+	}
+
+	if (val < XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0 - 1 &&
+	    val > XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK - 1) {
+		dev_err(priv->dev, "dt tx-refclk-sel %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->tx_refclk_sel = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-pll-selection", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,rx-pll-selection");
+		return rc;
+	}
+
+	if (val < 0 && val > 6) {
+		dev_err(priv->dev, "dt rx-pll-selection %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->rx_pllclk_sel = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-pll-selection", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,tx-pll-selection");
+		return rc;
+	}
+
+	if (val < 0 && val > 6) {
+		dev_err(priv->dev, "dt tx-pll-selection %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->tx_pllclk_sel = val;
+
+	rc = of_property_read_u32(node, "xlnx,transceiver-width", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,transceiver-width");
+		return rc;
+	}
+	if (val != 2 && val != 4) {
+		dev_err(priv->dev, "dt transceiver-width %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->transceiver_width = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-max-gt-line-rate", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,rx-max-gt-line-rate");
+		return rc;
+	}
+
+	if (val != 3 && val != 6 && val != 8 && val != 10 && val != 12) {
+		dev_err(priv->dev, "dt rx-max-gt-line-rate %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->rx_maxrate = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-max-gt-line-rate", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,tx-max-gt-line-rate");
+		return rc;
+	}
+
+	if (val != 3 && val != 6 && val != 8 && val != 10 && val != 12) {
+		dev_err(priv->dev, "dt tx-max-gt-line-rate %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->tx_maxrate = val;
+
+	rc = of_property_read_u32(node, "xlnx,use-gt-ch4-hdmi", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,use-gt-ch4-hdmi");
+		return rc;
+	}
+
+	if (val != 0 && val != 1) {
+		dev_err(priv->dev, "dt use-gt-ch4-hdmi %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->gt_as_tx_tmdsclk = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-frl-refclk-sel", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,rx-frl-refclk-sel");
+		return rc;
+	}
+
+	if (val < XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0 - 1 &&
+	    val > XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK - 1) {
+		dev_err(priv->dev, "dt rx-frl-refclk-sel %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->rx_frl_refclk_sel = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-frl-refclk-sel", &val);
+	if (rc < 0) {
+		dev_err(priv->dev, "unable to parse %s property\n",
+			"xlnx,tx-frl-refclk-sel");
+		return rc;
+	}
+
+	if (val < XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0 - 1 &&
+	    val > XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK - 1) {
+		dev_err(priv->dev, "dt tx-frl-refclk-sel %d is invalid\n",
+			val);
+		return -EINVAL;
+	}
+	xgtphycfg->tx_frl_refclk_sel = val;
+
+	priv->rxch4_gpio = devm_gpiod_get(priv->dev,
+					  "rxch4-sel", GPIOD_OUT_LOW);
+
+	if (IS_ERR(priv->rxch4_gpio)) {
+		if (PTR_ERR(priv->rxch4_gpio) != -EPROBE_DEFER)
+			dev_err(priv->dev, "rxch4-sel not setup in DT\n");
+		return PTR_ERR(priv->rxch4_gpio);
+	}
+
+	return rc;
+}
+
+static int xhdmiphy_clk_init(struct xhdmiphy_dev *priv)
+{
+	unsigned long dru_clk_rate = 0;
+	int err;
+
+	priv->axi_lite_clk = devm_clk_get(priv->dev, "vid_phy_axi4lite_aclk");
+	if (IS_ERR(priv->axi_lite_clk))
+		return dev_err_probe(priv->dev, PTR_ERR(priv->axi_lite_clk),
+				     "failed to get vid_phy_axi4lite_aclk\n");
+
+	priv->tmds_clk = devm_clk_get(priv->dev, "tmds_clock");
+	if (IS_ERR(priv->tmds_clk))
+		return dev_err_probe(priv->dev, PTR_ERR(priv->tmds_clk),
+				     "failed to get tmds_clock\n");
+
+	if (priv->conf.dru_present) {
+		priv->dru_clk = devm_clk_get(priv->dev, "drpclk");
+		if (IS_ERR(priv->dru_clk))
+			return dev_err_probe(priv->dev, PTR_ERR(priv->dru_clk),
+					     "failed to get drpclk\n");
+	} else {
+		dev_dbg(priv->dev, "DRU is not enabled from device tree\n");
+	}
+
+	err = clk_prepare_enable(priv->axi_lite_clk);
+	if (err) {
+		dev_err(priv->dev,
+			"failed to enable axi-lite clk (%d)\n", err);
+		return err;
+	}
+
+	err = clk_prepare_enable(priv->tmds_clk);
+	if (err) {
+		dev_err(priv->dev, "failed to enable tmds_clk (%d)\n", err);
+		goto err_disable_axiclk;
+	}
+
+	if (priv->conf.dru_present) {
+		err = clk_prepare_enable(priv->dru_clk);
+		if (err) {
+			dev_err(priv->dev,
+				"failed to enable nidru clk (%d)\n", err);
+			goto err_disable_tmds_clk;
+		}
+
+		dru_clk_rate = clk_get_rate(priv->dru_clk);
+		dev_dbg(priv->dev, "default dru-clk rate = %lu\n",
+			dru_clk_rate);
+		if (dru_clk_rate != XHDMIPHY_DRU_REF_CLK_HZ) {
+			err = clk_set_rate(priv->dru_clk,
+					   XHDMIPHY_DRU_REF_CLK_HZ);
+			if (err) {
+				dev_err(priv->dev,
+					"Cannot set rate : %d\n", err);
+				return err;
+			}
+			dru_clk_rate = clk_get_rate(priv->dru_clk);
+			dev_dbg(priv->dev,
+				"ref dru-clk rate = %lu\n", dru_clk_rate);
+		}
+	}
+
+	priv->conf.drpclk_freq = dru_clk_rate;
+	priv->conf.axilite_freq = clk_get_rate(priv->axi_lite_clk);
+
+	return 0;
+
+err_disable_tmds_clk:
+	clk_disable_unprepare(priv->tmds_clk);
+err_disable_axiclk:
+	clk_disable_unprepare(priv->axi_lite_clk);
+
+	return err;
+}
+
+static const struct of_device_id xhdmiphy_of_match[] = {
+	{ .compatible = "xlnx,v-hdmi-phy1-1.0" },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, xhdmiphy_of_match);
+
+static int xhdmiphy_probe(struct platform_device *pdev)
+{
+	struct device_node *child, *np = pdev->dev.of_node;
+	struct xhdmiphy_dev *priv;
+	struct phy_provider *provider;
+	struct xhdmiphy_lane *hdmiphy_lane;
+	struct platform_device *iface_pdev;
+	struct device_node *fnode;
+	struct resource *res;
+	struct phy *phy;
+	int index = 0, ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = &pdev->dev;
+
+	ret = xhdmiphy_parse_of(priv);
+	if (ret) {
+		dev_err(priv->dev, "Error parsing device tree\n");
+		return ret;
+	}
+
+	fnode = of_parse_phandle(np, "xlnx,hdmi-connector", 0);
+	if (!fnode) {
+		dev_err(&pdev->dev, "platform node not found\n");
+		of_node_put(fnode);
+	} else {
+		iface_pdev = of_find_device_by_node(fnode);
+		if (!iface_pdev) {
+			of_node_put(np);
+			return -ENODEV;
+		}
+		priv->data = dev_get_drvdata(&iface_pdev->dev);
+		if (!priv->data) {
+			dev_dbg(&pdev->dev,
+				"platform device not found -EPROBE_DEFER\n");
+			of_node_put(fnode);
+			return -EPROBE_DEFER;
+		}
+		of_node_put(fnode);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->phy_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->phy_base))
+		return PTR_ERR(priv->phy_base);
+
+	mutex_init(&priv->hdmiphy_mutex);
+
+	for_each_child_of_node(np, child) {
+		if (index >= XHDMIPHY_MAX_LANES) {
+			dev_err(&pdev->dev,
+				"MAX 4 PHY Lanes are supported\n");
+			return -E2BIG;
+		}
+
+		phy = devm_phy_create(&pdev->dev, child, &xhdmiphy_phyops);
+		if (IS_ERR(phy)) {
+			dev_err(&pdev->dev, "failed to create HDMI PHY\n");
+			return PTR_ERR(phy);
+		}
+
+		hdmiphy_lane = devm_kzalloc(&pdev->dev, sizeof(*hdmiphy_lane),
+					    GFP_KERNEL);
+		if (!hdmiphy_lane)
+			return -ENOMEM;
+
+		hdmiphy_lane->lane = index;
+		hdmiphy_lane->share_laneclk = -1;
+		priv->lanes[index] = hdmiphy_lane;
+
+		priv->lanes[index]->phy = phy;
+		phy_set_drvdata(phy, priv->lanes[index]);
+		hdmiphy_lane->data = priv;
+		index++;
+	}
+
+	priv->irq = platform_get_irq(pdev, 0);
+	if (priv->irq > 0) {
+		ret = devm_request_threaded_irq(&pdev->dev,
+						priv->irq, xhdmiphy_irq_handler,
+						xhdmiphy_irq_thread,
+						IRQF_TRIGGER_HIGH,
+						dev_name(priv->dev),
+						priv);
+		if (ret)
+			return ret;
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	ret = xhdmiphy_clk_init(priv);
+	if (ret)
+		return ret;
+
+	provider = devm_of_phy_provider_register(&pdev->dev, xhdmiphy_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(&pdev->dev, "registering provider failed\n");
+		ret = PTR_ERR(provider);
+		goto err_clk;
+	}
+	return 0;
+
+err_clk:
+	clk_disable_unprepare(priv->dru_clk);
+	clk_disable_unprepare(priv->tmds_clk);
+	clk_disable_unprepare(priv->axi_lite_clk);
+
+	return ret;
+}
+
+static int xhdmiphy_remove(struct platform_device *pdev)
+{
+	struct xhdmiphy_dev *priv = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(priv->dru_clk);
+	clk_disable_unprepare(priv->tmds_clk);
+	clk_disable_unprepare(priv->axi_lite_clk);
+
+	return 0;
+}
+
+static struct platform_driver xhdmiphy_driver = {
+	.probe = xhdmiphy_probe,
+	.remove = xhdmiphy_remove,
+	.driver = {
+		.name = "xilinx-hdmiphy",
+		.of_match_table	= xhdmiphy_of_match,
+	},
+};
+module_platform_driver(xhdmiphy_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Rajesh Gugulothu <gugulothu.rajesh@xilinx.com");
+MODULE_DESCRIPTION("Xilinx HDMI PHY driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xhdmiphy.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xhdmiphy.h
@@ -0,0 +1,1115 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _XHDMIPHY_H_
+#define _XHDMIPHY_H_
+
+#include <linux/types.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-hdmi.h>
+#include <linux/mutex.h>
+
+/* HDMIPHY core registers: general registers. */
+#define XHDMIPHY_REFCLKSEL_REG			0x010
+#define XHDMIPHY_COMMON_INIT_REG		0x014
+#define XHDMIPHY_PLL_LOCK_STATUS_REG		0x018
+#define XHDMIPHY_TX_INIT_REG			0x01c
+#define XHDMIPHY_RX_INIT_REG			0x024
+#define XHDMIPHY_POWERDOWN_CONTROL_REG		0x030
+#define XHDMIPHY_DRP_CONTROL_CH1_REG		0x040
+#define XHDMIPHY_DRP_STATUS_CH1_REG		0x050
+#define XHDMIPHY_DRP_CONTROL_COMMON_REG		0x060
+#define XHDMIPHY_DRP_STATUS_COMMON_REG		0x064
+#define XHDMIPHY_DRP_CONTROL_TXMMCM_REG		0x124
+#define XHDMIPHY_DRP_STATUS_TXMMCM_REG		0x128
+#define XHDMIPHY_DRP_CONTROL_RXMMCM_REG		0x144
+#define XHDMIPHY_DRP_STATUS_RXMMCM_REG		0x148
+#define XHDMIPHY_CPLL_CAL_PERIOD_REG		0x068
+#define XHDMIPHY_CPLL_CAL_TOL_REG		0x06c
+#define XHDMIPHY_GT_DBG_GPI_REG			0x068
+#define XHDMIPHY_GT_DBG_GPO_REG			0x06c
+#define XHDMIPHY_TX_BUFFER_BYPASS_REG		0x074
+#define XHDMIPHY_TX_DRIVER_CH12_REG		0x07c
+#define XHDMIPHY_TX_DRIVER_CH34_REG		0x080
+#define XHDMIPHY_TX_DRIVER_EXT_REG		0x084
+#define XHDMIPHY_TX_RATE_CH12_REG		0x08c
+#define XHDMIPHY_TX_RATE_CH34_REG		0x090
+#define XHDMIPHY_RX_RATE_CH12_REG		0x98
+#define XHDMIPHY_RX_RATE_CH34_REG		0x9c
+#define XHDMIPHY_DRP_RXCDR_CFG(n)		(0x0e + (n))
+#define XHDMIPHY_RX_CONTROL_REG			0x100
+#define XHDMIPHY_RX_EQ_CDR_REG			0x108
+#define XHDMIPHY_INTR_EN_REG			0x110
+#define XHDMIPHY_INTR_DIS_REG			0x114
+#define XHDMIPHY_INTR_STS_REG			0x11c
+#define XHDMIPHY_MMCM_TXUSRCLK_CTRL_REG		0x0120
+#define XHDMIPHY_BUFGGT_TXUSRCLK_REG		0x0134
+#define XHDMIPHY_MISC_TXUSRCLK_REG		0x0138
+#define XHDMIPHY_MMCM_RXUSRCLK_CTRL_REG		0x0140
+#define XHDMIPHY_BUFGGT_RXUSRCLK_REG		0x0154
+#define XHDMIPHY_MISC_RXUSRCLK_REG		0x0158
+#define XHDMIPHY_CLKDET_CTRL_REG		0x0200
+#define XHDMIPHY_CLKDET_FREQ_TMR_TO_REG		0x0208
+#define XHDMIPHY_CLKDET_FREQ_TX_REG		0x020c
+#define XHDMIPHY_CLKDET_FREQ_RX_REG		0x0210
+#define XHDMIPHY_CLKDET_TMR_TX_REG		0x0214
+#define XHDMIPHY_CLKDET_TMR_RX_REG		0x0218
+#define XHDMIPHY_CLKDET_FREQ_DRU_REG		0x021c
+#define XHDMIPHY_DRU_CTRL_REG			0x0300
+#define XHDMIPHY_DRU_CFREQ_L_REG(ch)		(0x0308 + (12 * ((ch) - 1)))
+#define XHDMIPHY_DRU_CFREQ_H_REG(ch)		(0x030C + (12 * ((ch) - 1)))
+#define XHDMIPHY_PATGEN_CTRL_REG		0x0340
+
+#define XHDMIPHY_INTR_STS_ALL_MASK		0xffffffff
+#define XHDMIPHY_INTR_ALL_MASK		(XHDMIPHY_INTR_TXRESETDONE_MASK | \
+					XHDMIPHY_INTR_RXRESETDONE_MASK | \
+					XHDMIPHY_INTR_CPLL_LOCK_MASK | \
+					XHDMIPHY_INTR_QPLL_LOCK_MASK | \
+					XHDMIPHY_INTR_TXALIGNDONE_MASK | \
+					XHDMIPHY_INTR_QPLL1_LOCK_MASK | \
+					XHDMIPHY_INTR_TXFREQCHANGE_MASK | \
+					XHDMIPHY_INTR_RXFREQCHANGE_MASK | \
+					XHDMIPHY_INTR_TXMMCMUSRCLK_LOCK_MASK | \
+					XHDMIPHY_INTR_RXMMCMUSRCLK_LOCK_MASK | \
+					XHDMIPHY_INTR_TXTMRTIMEOUT_MASK | \
+					XHDMIPHY_INTR_RXTMRTIMEOUT_MASK)
+
+#define XHDMIPHY_DRU_REF_CLK_HZ		100000000
+#define XHDMIPHY_MAX_LANES		4
+#define VPHY_DEVICE_ID_BASE		256
+
+#define XHDMIPHY_GTHE4				5
+#define XHDMIPHY_GTYE4				6
+#define XHDMIPHY_GTYE5				7
+#define XHDMIPHY_REFCLKSEL_MAX			5
+
+/* linerate ranges */
+#define XHDMIPHY_LRATE_3400			3400
+
+/* pll operating ranges */
+#define XHDMIPHY_QPLL0_MIN			9800000000LL
+#define XHDMIPHY_QPLL0_MAX			16375000000LL
+#define XHDMIPHY_QPLL1_MIN			8000000000LL
+#define XHDMIPHY_QPLL1_MAX			13000000000LL
+#define XHDMIPHY_CPLL_MIN			2000000000LL
+#define XHDMIPHY_CPLL_MAX			6250000000LL
+#define XHDMIPHY_LCPLL_MIN_REFCLK		120000000LL
+#define XHDMIPHY_RPLL_MIN_REFCLK		120000000LL
+
+/* HDMI 2.1 GT linerates */
+#define XHDMIPHY_LRATE_3G			3000000000
+#define XHDMIPHY_LRATE_6G			6000000000
+#define XHDMIPHY_LRATE_8G			8000000000
+#define XHDMIPHY_LRATE_10G			10000000000
+#define XHDMIPHY_LRATE_12G			12000000000
+
+#define XHDMIPHY_HDMI14_REFCLK_RANGE1		119990000
+#define XHDMIPHY_HDMI14_REFCLK_RANGE2		204687500
+#define XHDMIPHY_HDMI14_REFCLK_RANGE3		298500000
+#define XHDMIPHY_HDMI20_REFCLK_RANGE1		59400000
+#define XHDMIPHY_HDMI20_REFCLK_RANGE2		84570000
+#define XHDMIPHY_HDMI20_REFCLK_RANGE3		99000000
+#define XHDMIPHY_HDMI20_REFCLK_RANGE4		102343750
+#define XHDMIPHY_HDMI20_REFCLK_RANGE5		124990000
+#define XHDMIPHY_HDMI20_REFCLK_RANGE6		149500000
+#define XHDMIPHY_HDMI20_REFCLK_RANGE7		340000000
+
+#define XHDMIPHY_HDMI_GTYE5_DRU_LRATE		2500000000U
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK		200000000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK_MIN	199990000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK_MAX	200010000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK1		125000000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK1_MIN	124990000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK1_MAX	125010000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK2		400000000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK2_MIN	399990000LL
+#define XHDMIPHY_HDMI_GTYE5_DRU_REFCLK2_MAX	400010000LL
+#define XHDMIPHY_HDMI_GTYE5_LCPLL_REFCLK_MIN	120000000LL
+#define XHDMIPHY_HDMI_GTYE5_RPLL_REFCLK_MIN	120000000LL
+#define XHDMIPHY_HDMI_GTYE5_TX_MMCM_FVCO_MIN	2160000000U
+#define XHDMIPHY_HDMI_GTYE5_TX_MMCM_FVCO_MAX	4320000000U
+#define XHDMIPHY_HDMI_GTYE5_RX_MMCM_FVCO_MIN	2160000000U
+#define XHDMIPHY_HDMI_GTYE5_RX_MMCM_FVCO_MAX	4320000000U
+#define XHDMIPHY_HDMI_GTYE5_PLL_SCALE		1000
+#define XHDMIPHY_HDMI_DEFAULT_VS_VAL		0x1f
+#define XHDMIPHY_HDMI_DEFAULT_PC_PE_VAL		0x4
+#define XHDMIPHY_HDMI_GTYE5_RX_MMCM_SCALE	1
+#define XHDMIPHY_HDMI_GTYE5_TX_MMCM_SCALE	1
+
+#define XHDMIPHY_HDMI_GTYE4_DRU_LRATE		2500000000U
+#define XHDMIPHY_HDMI_GTYE4_DRU_REFCLK		156250000LL
+#define XHDMIPHY_HDMI_GTYE4_DRU_REFCLK_MIN	156240000LL
+#define XHDMIPHY_HDMI_GTYE4_DRU_REFCLK_MAX	156260000LL
+#define XHDMIPHY_HDMI_GTYE4_DRU_REFCLK2		400000000LL
+#define XHDMIPHY_HDMI_GTYE4_DRU_REFCLK2_MIN	399990000LL
+#define XHDMIPHY_HDMI_GTYE4_DRU_REFCLK2_MAX	400010000LL
+#define XHDMIPHY_HDMI_GTYE4_QPLL0_REFCLK_MIN	61250000LL
+#define XHDMIPHY_HDMI_GTYE4_QPLL1_REFCLK_MIN	50000000LL
+#define XHDMIPHY_HDMI_GTYE4_CPLL_REFCLK_MIN	50000000LL
+#define XHDMIPHY_HDMI_GTYE4_TX_MMCM_FVCO_MIN	800000000U
+#define XHDMIPHY_HDMI_GTYE4_TX_MMCM_FVCO_MAX	1600000000U
+#define XHDMIPHY_HDMI_GTYE4_RX_MMCM_FVCO_MIN	800000000U
+#define XHDMIPHY_HDMI_GTYE4_RX_MMCM_FVCO_MAX	1600000000U
+#define XHDMIPHY_HDMI_GTYE4_PLL_SCALE		1000
+#define XHDMIPHY_HDMI_GTYE4_RX_MMCM_SCALE	1
+#define XHDMIPHY_HDMI_GTYE4_TX_MMCM_SCALE	1
+
+#define XHDMIPHY_HDMI_GTHE4_DRU_LRATE		2500000000U
+#define XHDMIPHY_HDMI_GTHE4_DRU_REFCLK		156250000LL
+#define XHDMIPHY_HDMI_GTHE4_DRU_REFCLK_MIN	156240000LL
+#define XHDMIPHY_HDMI_GTHE4_DRU_REFCLK_MAX	156260000LL
+#define XHDMIPHY_HDMI_GTHE4_DRU_REFCLK2		400000000LL
+#define XHDMIPHY_HDMI_GTHE4_DRU_REFCLK2_MIN	399980000LL
+#define XHDMIPHY_HDMI_GTHE4_DRU_REFCLK2_MAX	400020000LL
+#define XHDMIPHY_HDMI_GTHE4_QPLL0_REFCLK_MIN	61250000LL
+#define XHDMIPHY_HDMI_GTHE4_QPLL1_REFCLK_MIN	50000000LL
+#define XHDMIPHY_HDMI_GTHE4_CPLL_REFCLK_MIN	50000000LL
+#define XHDMIPHY_HDMI_GTHE4_TX_MMCM_FVCO_MIN	800000000U
+#define XHDMIPHY_HDMI_GTHE4_TX_MMCM_FVCO_MAX	1600000000U
+#define XHDMIPHY_HDMI_GTHE4_RX_MMCM_FVCO_MIN	800000000U
+#define XHDMIPHY_HDMI_GTHE4_RX_MMCM_FVCO_MAX	1600000000U
+#define XHDMIPHY_HDMI21_FRL_REFCLK		400000000U
+#define XHDMIPHY_HDMI_GTHE4_DEFAULT_VS_VAL	0xb
+#define XHDMIPHY_HDMI_GTHE4_PLL_SCALE		1000
+#define XHDMIPHY_HDMI_GTHE4_RX_MMCM_SCALE	1
+#define XHDMIPHY_HDMI_GTHE4_TX_MMCM_SCALE	1
+
+/* 0x010: reference clock selections */
+#define XHDMIPHY_REFCLKSEL_QPLL0_MASK		0x0000000f
+#define XHDMIPHY_REFCLKSEL_CPLL_MASK		0x000000f0
+#define XHDMIPHY_REFCLKSEL_CPLL_SHIFT		4
+#define XHDMIPHY_REFCLKSEL_QPLL1_MASK		0x00000f00
+#define XHDMIPHY_REFCLKSEL_QPLL1_SHIFT		8
+#define XHDMIPHY_REFCLKSEL_SYSCLKSEL_MASK	0x0f000000
+#define XHDMIPHY_RXSYSCLKSEL_OUT_MASK(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 0x03000000 : 0x02000000); })
+#define XHDMIPHY_TXSYSCLKSEL_OUT_MASK(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 0x0C000000 : 0x08000000); })
+#define XHDMIPHY_RXSYSCLKSEL_DATA_MASK(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 0x30000000 : 0x01000000); })
+#define XHDMIPHY_TXSYSCLKSEL_DATA_MASK(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 0xC0000000 : 0x04000000); })
+#define XHDMIPHY_RXSYSCLKSEL_OUT_SHIFT(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 24 : 25); })
+#define XHDMIPHY_TXSYSCLKSEL_OUT_SHIFT(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 26 : 27); })
+#define XHDMIPHY_RXSYSCLKSEL_DATA_SHIFT(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 28 : 24); })
+#define XHDMIPHY_TXSYSCLKSEL_DATA_SHIFT(_G) ({ \
+		typeof(_G) (G) = (_G); \
+		((((G) == XHDMIPHY_GTTYPE_GTHE4) || \
+		 ((G) == XHDMIPHY_GTTYPE_GTYE4)) ? 30 : 26); })
+
+/* 0x018: pll lock status */
+#define XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(ch)		(0x01 << ((ch) - 1))
+#define XHDMIPHY_PLL_LOCK_STATUS_QPLL0_MASK		0x10
+#define XHDMIPHY_PLL_LOCK_STATUS_QPLL1_MASK		0x20
+#define XHDMIPHY_PLL_LOCK_STATUS_CPLL_ALL_MASK \
+		(XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH1) | \
+		 XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH2) | \
+		 XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH3) | \
+		 XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH4))
+#define XHDMIPHY_PLL_LOCK_STATUS_CPLL_HDMI_MASK \
+		(XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH1) | \
+		 XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH2) | \
+		 XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY_CHID_CH3))
+#define XHDMIPHY_PLL_LOCK_STATUS_RPLL_MASK		0xc0
+#define XHDMIPHY_PLL_LOCK_STATUS_LCPLL_MASK		0x300
+/* 0x01C, 0x024: TX_INIT, RX_INIT */
+#define XHDMIPHY_TXRX_INIT_GTRESET_MASK(ch)	(0x01 << (8 * ((ch) - 1)))
+#define XHDMIPHY_TXRX_MSTRESET_MASK(ch)		(0x20 << (8 * ((ch) - 1)))
+#define XHDMIPHY_TXRX_INIT_PLLGTRESET_MASK(ch)	(0x80 << (8 * ((ch) - 1)))
+
+#define XHDMIPHY_TXRX_INIT_GTRESET_ALL_MASK \
+		(XHDMIPHY_TXRX_INIT_GTRESET_MASK(XHDMIPHY_CHID_CH1) | \
+		 XHDMIPHY_TXRX_INIT_GTRESET_MASK(XHDMIPHY_CHID_CH2) | \
+		 XHDMIPHY_TXRX_INIT_GTRESET_MASK(XHDMIPHY_CHID_CH3) | \
+		 XHDMIPHY_TXRX_INIT_GTRESET_MASK(XHDMIPHY_CHID_CH4))
+#define XHDMIPHY_TXRX_INIT_PLLGTRESET_ALL_MASK \
+		(XHDMIPHY_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY_CHID_CH1) | \
+		 XHDMIPHY_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY_CHID_CH2) | \
+		 XHDMIPHY_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY_CHID_CH3) | \
+		 XHDMIPHY_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY_CHID_CH4))
+#define XHDMIPHY_RXPCS_RESET_MASK			0x10101010
+#define XHDMIPHY_TXPCS_RESET_MASK			0x10101010
+
+/* 0x02C: IBUFDS_GTXX_CTRL */
+#define XHDMIPHY_IBUFDS_GTXX_CTRL_GTREFCLK0_CEB_MASK	0x1
+#define XHDMIPHY_IBUFDS_GTXX_CTRL_GTREFCLK1_CEB_MASK	0x2
+
+/* 0x030: power down control */
+#define XHDMIPHY_POWERDOWN_CONTROL_CPLLPD_MASK(ch)	(0x01 << (8 * ((ch) - 1)))
+#define XHDMIPHY_POWERDOWN_CONTROL_QPLL0PD_MASK(ch)	(0x02 << (8 * ((ch) - 1)))
+#define XHDMIPHY_POWERDOWN_CONTROL_QPLL1PD_MASK(ch)	(0x04 << (8 * ((ch) - 1)))
+
+/* 0x040, 0x044, 0x048, 0x04C, 0x060: DRP_CONTROL_CH[1-4], DRP_CONTROL_COMMON */
+#define XHDMIPHY_DRP_CONTROL_DRPADDR_MASK	0x00000ff
+#define XHDMIPHY_DRP_CONTROL_DRPEN_MASK		0x00001000
+#define XHDMIPHY_DRP_CONTROL_DRPWE_MASK		0x00002000
+#define XHDMIPHY_DRP_CONTROL_DRPDI_MASK		0xffff0000
+#define XHDMIPHY_DRP_CONTROL_DRPDI_SHIFT	16
+
+/* 0x050, 0x054, 0x058, 0x05C, 0x064: DRP_STATUS_CH[1-4], DRP_STATUS_COMMON */
+#define XHDMIPHY_DRP_STATUS_DRPO_MASK		0x0ffff
+#define XHDMIPHY_DRP_STATUS_DRPRDY_MASK		0x10000
+#define XHDMIPHY_DRP_STATUS_DRPBUSY_MASK	0x20000
+
+/* 0x068: cpll cal period */
+#define XHDMIPHY_CPLL_CAL_PERIOD_MASK		0x3ffff
+
+/* 0x06C: cpll cal tolerance */
+#define XHDMIPHY_CPLL_CAL_TOL_MASK		0x3ffff
+
+/* 0x068: gpi */
+#define XHDMIPHY_TX_GPI_MASK(ch)		(0x01 << ((ch) - 1))
+#define XHDMIPHY_RX_GPI_MASK(ch)		(0x10 << ((ch) - 1))
+
+/* 0x06C: gpo */
+#define XHDMIPHY_TX_GPO_MASK(ch)		(0x01 << ((ch) - 1))
+#define XHDMIPHY_TX_GPO_MASK_ALL(nch)		(((nch) == 3) ? 0x7 : 0xf)
+#define XHDMIPHY_TX_GPO_SHIFT			0
+
+#define XHDMIPHY_RX_GPO_MASK(ch)		(0x10 << ((ch) - 1))
+#define XHDMIPHY_RX_GPO_MASK_ALL(nch)		(((nch) == 3) ? 0x70 : 0xf0)
+#define XHDMIPHY_RX_GPO_SHIFT			4
+
+/* 0x074: Tx buffer bypass */
+#define XHDMIPHY_TX_BUFFER_BYPASS_TXPHDLYRESET_MASK(ch) \
+						(0x01 << (8 * ((ch) - 1)))
+#define XHDMIPHY_TX_BUFFER_BYPASS_TXPHALIGN_MASK(ch) \
+						(0x02 << (8 * ((ch) - 1)))
+
+/* 0x07c, 0x080: TX_DRIVER_CH12, TX_DRIVER_CH34 */
+#define XHDMIPHY_TX_TXDIFFCTRL_MASK	0xf
+#define XHDMIPHY_TX_DRIVER_TXDIFFCTRL_MASK(ch) \
+				(0x000F << (16 * (((ch) - 1) % 2)))
+#define XHDMIPHY_TX_DRIVER_TXDIFFCTRL_SHIFT(ch) \
+				(16 * (((ch) - 1) % 2))
+#define XHDMIPHY_TX_DRIVER_TXPOSTCURSOR_MASK(ch) \
+				(0x07C0 << (16 * (((ch) - 1) % 2)))
+#define XHDMIPHY_TX_DRIVER_TXPOSTCURSOR_SHIFT(ch) \
+				(6 + (16 * (((ch) - 1) % 2)))
+#define XHDMIPHY_TX_DRIVER_TXPRECURSOR_MASK(ch) \
+				(0xF800 << (16 * (((ch) - 1) % 2)))
+#define XHDMIPHY_TX_DRIVER_TXPRECURSOR_SHIFT(ch) \
+				(11 + (16 * (((ch) - 1) % 2)))
+
+/* 0x084: Tx driver exit */
+#define XHDMIPHY_TX_EXT_TXDIFFCTRL_MASK	0x10
+#define XHDMIPHY_TX_DRIVER_EXT_TXDIFFCTRL_MASK(ch) \
+						(0x0001 << (8 * ((ch) - 1)))
+#define XHDMIPHY_TX_DRIVER_EXT_TXDIFFCTRL_SHIFT(ch) \
+						(8 * ((ch) - 1))
+
+/* 0x08C, 0x090: tx rate ch12, tx rate ch34 */
+#define XHDMIPHY_TX_RATE_MASK(ch)	(0x00ff << (16 * (((ch) - 1) % 2)))
+#define XHDMIPHY_TX_RATE_SHIFT(ch)	(16 * (((ch) - 1) % 2))
+
+/* 0x098, 0x09C: rx rate ch12, rx rate ch34 */
+#define XHDMIPHY_RX_RATE_MASK(ch)	(0x00ff << (16 * (((ch) - 1) % 2)))
+#define XHDMIPHY_RX_RATE_SHIFT(ch)	(16 * (((ch) - 1) % 2))
+
+/* 0x104: rx eq cdr */
+#define XHDMIPHY_RX_CONTROL_RXLPMEN_MASK(ch)	(0x01 << (8 * ((ch) - 1)))
+#define XHDMIPHY_RX_STATUS_RXCDRHOLD_MASK(ch)	(0x02 << (8 * ((ch) - 1)))
+#define XHDMIPHY_RX_STATUS_RXOSOVRDEN_MASK(ch)	(0x04 << (8 * ((ch) - 1)))
+#define XHDMIPHY_RX_STATUS_RXLPMLFKLOVRDEN_MASK(ch) \
+						(0x08 << (8 * ((ch) - 1)))
+#define XHDMIPHY_RX_STATUS_RXLPMHFOVRDEN_MASK(ch) \
+						(0x10 << (8 * ((ch) - 1)))
+#define XHDMIPHY_RX_CONTROL_RXLPMEN_ALL_MASK \
+		(XHDMIPHY_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY_CHID_CH1) | \
+		 XHDMIPHY_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY_CHID_CH2) | \
+		 XHDMIPHY_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY_CHID_CH3) | \
+		 XHDMIPHY_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY_CHID_CH4))
+
+/* 0x110, 0x114, 0x118, 0x11c: INTR_EN, INTR_DIS, INTR_MASK, INTR_STS */
+#define XHDMIPHY_INTR_TXRESETDONE_MASK			BIT(0)
+#define XHDMIPHY_INTR_RXRESETDONE_MASK			BIT(1)
+#define XHDMIPHY_INTR_CPLL_LOCK_MASK			BIT(2)
+#define XHDMIPHY_INTR_QPLL0_LOCK_MASK			BIT(3)
+#define XHDMIPHY_INTR_LCPLL_LOCK_MASK			BIT(3)
+#define XHDMIPHY_INTR_TXALIGNDONE_MASK			BIT(4)
+#define XHDMIPHY_INTR_QPLL1_LOCK_MASK			BIT(5)
+#define XHDMIPHY_INTR_RPLL_LOCK_MASK			BIT(5)
+#define XHDMIPHY_INTR_TXFREQCHANGE_MASK			BIT(6)
+#define XHDMIPHY_INTR_RXFREQCHANGE_MASK			BIT(7)
+#define XHDMIPHY_INTR_TXMMCMUSRCLK_LOCK_MASK		BIT(9)
+#define XHDMIPHY_INTR_RXMMCMUSRCLK_LOCK_MASK		BIT(10)
+#define XHDMIPHY_INTR_TXGPO_RE_MASK			BIT(11)
+#define XHDMIPHY_INTR_RXGPO_RE_MASK			BIT(12)
+#define XHDMIPHY_INTR_TXTMRTIMEOUT_MASK			BIT(30)
+#define XHDMIPHY_INTR_RXTMRTIMEOUT_MASK			BIT(31)
+#define XHDMIPHY_INTR_QPLL_LOCK_MASK		XHDMIPHY_INTR_QPLL0_LOCK_MASK
+
+/* 0x120, 0x140: MMCM_TXUSRCLK_CTRL, MMCM_RXUSRCLK_CTRL */
+#define XHDMIPHY_MMCM_USRCLK_CTRL_RST_MASK		BIT(1)
+#define XHDMIPHY_MMCM_USRCLK_CTRL_LOCKED_MASK		BIT(9)
+#define XHDMIPHY_MMCM_USRCLK_CTRL_PWRDWN_MASK		BIT(10)
+#define XHDMIPHY_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK	BIT(11)
+#define XHDMIPHY_MMCM_USRCLK_CTRL_CLKINSEL_MASK		BIT(12)
+
+#define XHDMIPHY_BUFGGT_XXUSRCLK_DIV_MASK		GENMASK(3, 1)
+#define XHDMIPHY_BUFGGT_XXUSRCLK_DIV_SHIFT		1
+
+/* 0x138, 0x158: MISC_TXUSRCLK_REG, MISC_RXUSERCLK_REG */
+#define XHDMIPHY_MISC_XXUSRCLK_CKOUT1_OEN_MASK		BIT(0)
+#define XHDMIPHY_MISC_XXUSRCLK_REFCLK_CEB_MASK		BIT(1)
+
+/* 0x200: clock detector control */
+#define XHDMIPHY_CLKDET_CTRL_RUN_MASK			BIT(0)
+#define XHDMIPHY_CLKDET_CTRL_TX_TMR_CLR_MASK		BIT(1)
+#define XHDMIPHY_CLKDET_CTRL_RX_TMR_CLR_MASK		BIT(2)
+#define XHDMIPHY_CLKDET_CTRL_RX_FREQ_RST_MASK		BIT(4)
+#define XHDMIPHY_CLKDET_CTRL_FREQ_LOCK_THRESH_SHIFT	5
+#define XHDMIPHY_CLKDET_CTRL_TX_FREQ_RST_MASK		0x8
+/* 0x300: dru control */
+#define XHDMIPHY_DRU_CTRL_RST_MASK(ch)			(0x01 << (8 * ((ch) - 1)))
+#define XHDMIPHY_DRU_CTRL_EN_MASK(ch)			(0x02 << (8 * ((ch) - 1)))
+/* 0x30C, 0x318, 0x324, 0x330: DRU_CFREQ_H_CH[1-4] */
+#define XHDMIPHY_DRU_CFREQ_H_MASK		0x1f
+
+/* 0x340 TMDS PATGEN */
+#define XHDMIPHY_PATGEN_CTRL_ENABLE_MASK	0x80000000
+#define XHDMIPHY_PATGEN_CTRL_RATIO_MASK		0x7
+
+#define XHDMIPHY_CH2IDX(id)		((id) - XHDMIPHY_CHID_CH1)
+#define XHDMIPHY_ISTXMMCM(id)		((id) == XHDMIPHY_CHID_TXMMCM)
+#define XHDMIPHY_ISRXMMCM(id)		((id) == XHDMIPHY_CHID_RXMMCM)
+
+#define xhdmiphy_is_tx_using_cpll(inst, chid) ({ \
+			(XHDMIPHY_PLL_CPLL == \
+			 xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX, chid)); })
+#define xhdmiphy_is_rx_using_cpll(inst, chid) ({ \
+			(XHDMIPHY_PLL_CPLL == \
+			 xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX, chid)); })
+
+/* Following Data is written in to the DRP addresses.
+ * To know the offsets, affected bit positions
+ * and other details, please refer GT Userguide
+ *
+ */
+
+/* masks and registers of GTHE4 DRP */
+#define XDRP_GTHE4_CHN_REG_0028		0x0028
+#define XDRP_GTHE4_CHN_REG_002A		0x002a
+#define XDRP_GTHE4_CHN_REG_00CB		0x00cb
+#define XDRP_GTHE4_CHN_REG_00CC		0x00cc
+#define XDRP_GTHE4_CHN_REG_00BC		0x00bc
+#define XDRP_GTHE4_CHN_REG_0063		0x0063
+#define XDRP_GTHE4_CHN_REG_006D		0x006d
+#define XDRP_GTHE4_CHN_REG_007A		0x007a
+#define XDRP_GTHE4_CHN_REG_007C		0x007c
+#define XDRP_GTHE4_CHN_REG_0011		0x0011
+#define XDRP_GTHE4_CHN_REG_00AF		0x00af
+#define XDRP_GTHE4_CHN_REG_0066		0x0066
+#define XDRP_GTHE4_CHN_REG_0003		0x0003
+#define XDRP_GTHE4_CHN_REG_0116		0x0116
+#define XDRP_GTHE4_CHN_REG_00FB		0x00fb
+#define XDRP_GTHE4_CHN_REG_009D		0x009d
+#define XDRP_GTHE4_CHN_REG_0100		0x0100
+#define XDRP_GTHE4_CHN_REG_003E		0x003e
+#define XDRP_GTHE4_CHN_REG_0085		0x0085
+#define XDRP_GTHE4_CHN_REG_0073		0x0073
+#define XDRP_GTHE4_CHN_REG_00FF		0x00ff
+#define XDRP_GTHE4_CHN_REG_009C		0x009c
+
+#define XDRP_GTHE4_CHN_REG_0063_RXOUT_DIV_MASK			0x07
+#define XDRP_GTHE4_CHN_REG_0063_FLD_RXOUT_DIV_MASK		0x7
+#define XDRP_GTHE4_CHN_REG_007C_TXOUT_DIV_MASK			0x700
+#define XDRP_GTHE4_CHN_REG_007C_FLD_TX_RXDETECT_REF_MASK	0x7
+#define XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_MASK		0xff
+#define XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_SHIFT		8
+#define XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_45_MASK		0x1
+#define XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_45_SHIFT		7
+#define XDRP_GTHE4_CHN_REG_002A_FLD_A_TXDIFFCTRL_MASK		0x1f
+#define XDRP_GTHE4_CHN_REG_002A_FLD_A_TXDIFFCTRL_SHIFT		11
+#define XDRP_GTHE4_CHN_REG_0028_CPLL_FBDIV_MASK			0xff80
+#define XDRP_GTHE4_CHN_REG_002A_CPLL_REFCLK_DIV_MASK		0xf800
+#define XDRP_GTHE4_CHN_REG_003E_DRP_VAL1			57442
+#define XDRP_GTHE4_CHN_REG_003E_DRP_VAL2			57415
+#define XDRP_GTHE4_CHN_REG_0066_RX_INT_DATAWIDTH_MASK		0xf
+#define XDRP_GTHE4_CHN_REG_0003_RX_DATAWIDTH_MASK		0x1e0
+#define XDRP_GTHE4_CHN_REG_0003_RX_DATAWIDTH_ENC_MASK		0xf
+#define XDRP_GTHE4_CHN_REG_0003_RX_DATAWIDTH_ENC_SHIFT		5
+#define XDRP_GTHE4_CHN_REG_0116_CH_RX_HSPMUX_MASK		0x00ff
+#define XDRP_GTHE4_CHN_REG_00FB_PREIQ_FREQ_BST_MASK		0x0030
+#define XDRP_GTHE4_CHN_REG_00FB_TXPI_BIASSET_MASK		0x0006
+#define XDRP_GTHE4_CHN_REG_009C_TXPI_CFG3_CFG4_MASK		0x0060
+#define XDRP_GTHE4_CHN_REG_0116_CH_TX_HSPMUX_MASK		0xff00
+#define XDRP_GTHE4_CHN_REG_007A_TXCLK25_MASK			0xf800
+#define XDRP_GTHE4_CHN_REG_007A_TXCLK25_SHIFT			11
+#define XDRP_GTHE4_CHN_REG_006D_RXCLK25_MASK			0x00f8
+#define XDRP_GTHE4_CHN_REG_0066_RX_WIDEMODE_CDR_MASK_VAL	0x3
+#define XDRP_GTHE4_CHN_REG_007A_TX_DATA_WIDTH_MASK		0xf
+#define XDRP_GTHE4_CHN_REG_0085_TX_INT_DATAWIDTH_MASK		0x3
+#define XDRP_GTHE4_CHN_REG_0085_TX_INT_DATAWIDTH_SHIFT		10
+#define XDRP_GTHE4_CHN_REG_00AF_RXCDR_CGF2_GEN2_MASK		0x3ff
+#define XDRP_GTHE4_CHN_REG_0011_RXCDR_CGF3_GEN2_MASK		0x3f
+#define XDRP_GTHE4_CHN_REG_0011_RXCDR_CGF3_GEN2_SHIFT		10
+#define XDRP_GTHE4_CHN_REG_0066_RX_WIDEMODE_CDR_MASK		0xc
+
+#define XDRP_GTHE4_CMN_REG_0014		0x0014
+#define XDRP_GTHE4_CMN_REG_0018		0x0018
+#define XDRP_GTHE4_CMN_REG_0094		0x0094
+#define XDRP_GTHE4_CMN_REG_0098		0x0098
+#define XDRP_GTHE4_CMN_REG_008D		0x008d
+#define XDRP_GTHE4_CMN_REG_0016		0x0016
+#define XDRP_GTHE4_CMN_REG_000D		0x000d
+#define XDRP_GTHE4_CMN_REG_0096		0x0096
+#define XDRP_GTHE4_CMN_REG_0019		0x0019
+#define XDRP_GTHE4_CMN_REG_0099		0x0099
+#define XDRP_GTHE4_CMN_REG_0030		0x0030
+#define XDRP_GTHE4_CMN_REG_00B0		0x00b0
+
+#define XDRP_GTHE4_CMN_REG_0014_FLD_QPLL0_INIT_CFG1_MASK	0xff
+#define XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_MASK		0xf80
+#define XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_MASK1		0x1f
+#define XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_SHIFT		6
+#define XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_SHIFT1		7
+#define XDRP_GTHE4_CMN_REG_000D_PPFX_CFG_MASK			0x0fc0
+#define XDRP_GTHE4_CMN_REG_0019_QPLLX_LPF_MASK			0x0003
+#define XDRP_GTHE4_CMN_REG_0030_QPLLX_CFG4_MASK			0x00e7
+
+#define XHDMIPHY_DRP_CPLL_VCO_RANGE1		3000
+#define XHDMIPHY_DRP_CPLL_VCO_RANGE2		4250
+#define XHDMIPHY_DRP_CPLL_CFG0_VAL1		0x01fa
+#define XHDMIPHY_DRP_CPLL_CFG0_VAL2		0x0ffa
+#define XHDMIPHY_DRP_CPLL_CFG0_VAL3		0x03fe
+#define XHDMIPHY_DRP_CPLL_CFG1_VAL1		0x0023
+#define XHDMIPHY_DRP_CPLL_CFG1_VAL2		0x0021
+#define XHDMIPHY_DRP_CPLL_CFG2_VAL1		0x0002
+#define XHDMIPHY_DRP_CPLL_CFG2_VAL2		0x0202
+#define XHDMIPHY_DRP_CPLL_CFG2_VAL3		0x0203
+#define XHDMIPHY_DRP_QPLL_VCO_RANGE1		15000
+#define XHDMIPHY_DRP_QPLL_VCO_RANGE2		13000
+#define XHDMIPHY_DRP_QPLL_VCO_RANGE3		11000
+#define XHDMIPHY_DRP_QPLL_VCO_RANGE4		7000
+#define XHDMIPHY_DRP_QPLL_NFBDIV		40
+#define XHDMIPHY_DRP_QPLL_CP_VAL1		0x007f
+#define XHDMIPHY_DRP_QPLL_CP_VAL2		0x03ff
+#define XHDMIPHY_DRP_QPLL_LPF_VAL1		0x3
+#define XHDMIPHY_DRP_QPLL_LPF_VAL2		0x1
+#define XHDMIPHY_DRP_QPLL_CLKOUT_RANGE1		7500
+#define XHDMIPHY_DRP_QPLL_CLKOUT_RANGE2		3500
+#define XHDMIPHY_DRP_QPLL_CLKOUT_RANGE3		5500
+#define XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL1	0x0e00
+#define XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL2	0x0800
+#define XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL3	0x0600
+#define XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL4	0x0400
+#define XHDMIPHY_DRP_PPF_MUX_TERM_CTRL0_VAL1	0x0100
+#define XHDMIPHY_DRP_PPF_MUX_TERM_CTRL0_VAL2	0x0000
+#define XHDMIPHY_DRP_Q_TERM_CLK_VAL1		0x2
+#define XHDMIPHY_DRP_Q_TERM_CLK_VAL2		0x0
+#define XHDMIPHY_DRP_Q_TERM_CLK_VAL3		0x6
+#define XHDMIPHY_DRP_Q_DCRNT_CLK_VAL1		0x5
+#define XHDMIPHY_DRP_Q_DCRNT_CLK_VAL2		0x4
+#define XHDMIPHY_DRP_Q_DCRNT_CLK_VAL3		0x3
+#define XHDMIPHY_DRP_Q_DCRNT_CLK_SHIFT		5
+#define XHDMIPHY_DRP_LINERATEKHZ_1		16400000
+#define XHDMIPHY_DRP_LINERATEKHZ_2		10400000
+#define XHDMIPHY_DRP_LINERATEKHZ_3		10000000
+#define XHDMIPHY_DRP_LINERATEKHZ_4		20000000
+#define XHDMIPHY_DRP_LINERATEKHZ_5		16375000
+#define XHDMIPHY_DRP_LINERATEKHZ_6		8000000
+#define XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL1	0x0010
+#define XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL2	0x0018
+#define XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL3	0x0012
+#define XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL1	3
+#define XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL2	2
+#define XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL3	1
+#define XHDMIPHY_DRP_PREIQ_FREQ_BST_SHIFT	4
+#define XHDMIPHY_DRP_TXOUT_OFFSET		8
+
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE1		7500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE2		3500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE3		5500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE4		14110
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE5		14000
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE8		7000
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE9		6500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE10		5500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE11		5156
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE12		4500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE13		4000
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE14		3500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE15		3000
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE16		2500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE17		7500
+#define XHDMIPHY_DRP_PLL_CLKOUT_RANGE18		2000
+
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL1		0x0004
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL2		0x0104
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL3		0x2004
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL4		0x0002
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL5		0x0102
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL6		0x2102
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL7		0x2202
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL8		0x0200
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL9		0x1300
+#define XHDMIPHY_DRP_RXPI_CFG0_VAL10		0x3300
+#define XHDMIPHY_DRP_RXPI_CFG1_VAL1		0x0000
+#define XHDMIPHY_DRP_RXPI_CFG1_VAL2		0x0015
+#define XHDMIPHY_DRP_RXPI_CFG1_VAL3		0x0045
+#define XHDMIPHY_DRP_RXPI_CFG1_VAL4		0x00fd
+#define XHDMIPHY_DRP_RXPI_CFG1_VAL5		0x00ff
+#define XHDMIPHY_DRP_TXPH_CFG_VAL1		0x0723
+#define XHDMIPHY_DRP_TXPH_CFG_VAL2		0x0323
+
+#define XHDMIPHY_DRP_TX_DATAWIDTH_VAL1		40
+#define XHDMIPHY_DRP_TX_DATAWIDTH_VAL2		20
+#define XHDMIPHY_DRP_TX_OUTDIV_VAL1		1
+#define XHDMIPHY_DRP_TX_OUTDIV_VAL2		2
+
+#define XHDMIPHY_DRP_TXPI_CFG_VAL1		0x0000
+#define XHDMIPHY_DRP_TXPI_CFG_VAL2		0x0054
+#define XHDMIPHY_DRP_TXPI_CFG_VAL3		0x03df
+#define XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL1	0x0
+#define XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL2	0x1
+#define XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL3	0x2
+#define XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL4	0x3
+#define XHDMIPHY_DRP_TXPI_CFG3_CFG4_SHIFT	5
+#define XHDMIPHY_DRP_TXPI_BIASSET_VAL1		3
+#define XHDMIPHY_DRP_TXPI_BIASSET_VAL2		2
+#define XHDMIPHY_DRP_TXPI_BIASSET_VAL3		1
+#define XHDMIPHY_DRP_TXPI_BIASSET_SHIFT		1
+#define XHDMIPHY_DRP_CH_HSPMUX_VAL1		0x68
+#define XHDMIPHY_DRP_CH_HSPMUX_VAL2		0x44
+#define XHDMIPHY_DRP_CH_HSPMUX_VAL3		0x24
+#define XHDMIPHY_DRP_CH_HSPMUX_VAL4		0x3c
+#define XHDMIPHY_DRP_CH_HSPMUX_SHIFT		8
+#define XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL1	2
+#define XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL2	1
+#define XHDMIPHY_DRP_PLLX_CLKOUT_VAL1		0x68
+#define XHDMIPHY_DRP_PLLX_CLKOUT_VAL2		0x44
+#define XHDMIPHY_DRP_PLLX_CLKOUT_VAL3		0x24
+#define XHDMIPHY_DRP_PLLX_CLKOUT_VAL4		0x3c
+
+#define XHDMIPHY_DRP_RX_DATAWIDTH_80		80
+#define XHDMIPHY_DRP_RX_DATAWIDTH_64		64
+#define XHDMIPHY_DRP_RX_DATAWIDTH_40		40
+#define XHDMIPHY_DRP_RX_DATAWIDTH_32		32
+#define XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL1	0x2
+#define XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL2	0x1
+#define XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL3	0x0
+#define XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT	2
+#define XHDMIPHY_RXCDR_CFG_WORD0		0x0000
+#define XHDMIPHY_RXCDR_CFG_WORD1		0x0000
+#define XHDMIPHY_RXCDR_CFG_WORD2		0x0262
+#define XHDMIPHY_RXCDR_CFG_WORD3		0x0000
+#define XHDMIPHY_RXCDR_CFG_WORD4		0x0000
+#define XHDMIPHY_RXCDR_CFG_WORD2_RXDIV		0x10
+#define XHDMIPHY_DRP_RXCDR_CFG_GEN3(n)		(0xa2 + (n))
+#define XHDMIPHY_DRP_RXCDR_CFG_WORD3		0x11
+
+/* masks and registers of mmcme4 DRP */
+#define XHDMIPHY_MMCM4_CLKOUT0_REG1		0x08
+#define XHDMIPHY_MMCM4_CLKOUT0_REG2		0x09
+#define XHDMIPHY_MMCM4_CLKOUT1_REG1		0x0a
+#define XHDMIPHY_MMCM4_CLKOUT1_REG2		0x0b
+#define XHDMIPHY_MMCM4_CLKOUT2_REG1		0x0c
+#define XHDMIPHY_MMCM4_CLKOUT2_REG2		0x0d
+#define XHDMIPHY_MMCM4_CLKFBOUT_REG1		0x14
+#define XHDMIPHY_MMCM4_CLKFBOUT_REG2		0x15
+#define XHDMIPHY_MMCM4_DIVCLK_DIV_REG		0x16
+#define XHDMIPHY_MMCM4_DRP_LOCK_REG1		0x18
+#define XHDMIPHY_MMCM4_DRP_LOCK_REG2		0x19
+#define XHDMIPHY_MMCM4_DRP_LOCK_REG3		0x1a
+#define XHDMIPHY_MMCM4_DRP_FILTER_REG1		0x4e
+#define XHDMIPHY_MMCM4_DRP_FILTER_REG2		0x4f
+#define XHDMIPHY_MMCM4_PWR_REG			0x27
+#define XHDMIPHY_MMCM4_WRITE_VAL		0xffff
+
+/* registers and masks of mmcme5 DRP */
+#define XHDMIPHY_MMCM5_DRP_CLKFBOUT_1_REG	0x0c
+#define XHDMIPHY_MMCM5_DRP_CLKFBOUT_2_REG	0x0d
+#define XHDMIPHY_MMCM5_DRP_DIVCLK_DIVIDE_REG	0x21
+#define XHDMIPHY_MMCM5_DRP_DESKEW_REG		0x20
+#define XHDMIPHY_MMCM5_DRP_CLKOUT0_REG1		0x0e
+#define XHDMIPHY_MMCM5_DRP_CLKOUT0_REG2		0x0f
+#define XHDMIPHY_MMCM5_DRP_CLKOUT1_REG1		0x10
+#define XHDMIPHY_MMCM5_DRP_CLKOUT1_REG2		0x11
+#define XHDMIPHY_MMCM5_DRP_CLKOUT2_REG1		0x12
+#define XHDMIPHY_MMCM5_DRP_CLKOUT2_REG2		0x13
+#define XHDMIPHY_MMCM5_DRP_CP_REG1		0x1e
+#define XHDMIPHY_MMCM5_DRP_RES_REG1		0x2a
+#define XHDMIPHY_MMCM5_DRP_LOCK_REG1		0x27
+#define XHDMIPHY_MMCM5_DRP_LOCK_REG2		0x28
+#define XHDMIPHY_MMCM5_WRITE_VAL		0xFFFF
+#define XHDMIPHY_MMCM5_CP_RES_MASK		0xf
+#define XHDMIPHY_MMCM5_RES_MASK			0x1e
+#define XHDMIPHY_MMCM5_LOCK1_MASK1		0x8000
+#define XHDMIPHY_MMCM5_LOCK1_MASK2		0x7fff
+
+enum color_depth {
+	XVIDC_BPC_6 = 6,
+	XVIDC_BPC_8 = 8,
+	XVIDC_BPC_10 = 10,
+	XVIDC_BPC_12 = 12,
+	XVIDC_BPC_14 = 14,
+	XVIDC_BPC_16 = 16,
+};
+
+enum ppc {
+	XVIDC_PPC_1 = 1,
+	XVIDC_PPC_2 = 2,
+	XVIDC_PPC_4 = 4,
+	XVIDC_PPC_8 = 8,
+};
+
+enum color_fmt {
+	/* streaming video formats */
+	XVIDC_CSF_RGB = 0,
+	XVIDC_CSF_YCRCB_444 = 1,
+	XVIDC_CSF_YCRCB_422 = 2,
+	XVIDC_CSF_YCRCB_420 = 3,
+	XVIDC_CSF_YONLY = 4,
+	XVIDC_CSF_RGBA = 5,
+	XVIDC_CSF_YCRCBA_444 = 6,
+};
+
+enum gt_type {
+	XHDMIPHY_GTTYPE_GTHE4 = 5,
+	XHDMIPHY_GTTYPE_GTYE4 = 6,
+	XHDMIPHY_GTTYPE_GTYE5 = 7,
+};
+
+enum prot_type {
+	XHDMIPHY_PROT_HDMI = 1,
+	XHDMIPHY_PROT_HDMI21 = 2,
+	XHDMIPHY_PROT_NONE = 3
+};
+
+enum dir {
+	XHDMIPHY_DIR_RX = 0,
+	XHDMIPHY_DIR_TX = 1,
+	XHDMIPHY_DIR_NONE = 2
+};
+
+enum pll_type {
+	XHDMIPHY_PLL_CPLL = 1,
+	XHDMIPHY_PLL_QPLL = 2,
+	XHDMIPHY_PLL_QPLL0 = 3,
+	XHDMIPHY_PLL_QPLL1 = 4,
+	XHDMIPHY_PLL_LCPLL = 5,
+	XHDMIPHY_PLL_RPLL = 6,
+	XHDMIPHY_PLL_UNKNOWN = 7,
+};
+
+enum chid {
+	XHDMIPHY_CHID_CH1 = 1,
+	XHDMIPHY_CHID_CH2 = 2,
+	XHDMIPHY_CHID_CH3 = 3,
+	XHDMIPHY_CHID_CH4 = 4,
+	XHDMIPHY_CHID_CMN0 = 5, /* QPLL, QPLL0, LCPLL */
+	XHDMIPHY_CHID_CMN1 = 6, /* QPLL1, RPLL */
+	XHDMIPHY_CHID_CHA = 7,
+	XHDMIPHY_CHID_CMNA = 8,
+	XHDMIPHY_CHID_TXMMCM = 9,
+	XHDMIPHY_CHID_RXMMCM = 10,
+	XHDMIPHY_CHID_CMN = XHDMIPHY_CHID_CMN0,
+};
+
+enum refclk_sel {
+	XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0 = 1,
+	XHDMIPHY_PLL_REFCLKSEL_GTREFCLK1 = 2,
+	XHDMIPHY_PLL_REFCLKSEL_GTNORTHREFCLK0 = 3,
+	XHDMIPHY_PLL_REFCLKSEL_GTNORTHREFCLK1 = 4,
+	XHDMIPHY_PLL_REFCLKSEL_GTSOUTHREFCLK0 = 5,
+	XHDMIPHY_PLL_REFCLKSEL_GTSOUTHREFCLK1 = 6,
+	XHDMIPHY_PLL_REFCLKSEL_GTEASTREFCLK0 = 3,
+	XHDMIPHY_PLL_REFCLKSEL_GTEASTREFCLK1 = 4,
+	XHDMIPHY_PLL_REFCLKSEL_GTWESTREFCLK0 = 5,
+	XHDMIPHY_PLL_REFCLKSEL_GTWESTREFCLK1 = 6,
+	XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK = 7,
+};
+
+enum sysclk_data_sel {
+	XHDMIPHY_SYSCLKSELDATA_PLL0_OUTCLK = 0,
+	XHDMIPHY_SYSCLKSELDATA_PLL1_OUTCLK = 1,
+	XHDMIPHY_SYSCLKSELDATA_CPLL_OUTCLK = 0,
+	XHDMIPHY_SYSCLKSELDATA_QPLL_OUTCLK = 1,
+	XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK = 3,
+	XHDMIPHY_SYSCLKSELDATA_QPLL1_OUTCLK = 2,
+};
+
+enum sysclk_outsel {
+	XHDMIPHY_SYSCLKSELOUT_CPLL_REFCLK = 0,
+	XHDMIPHY_SYSCLKSELOUT_QPLL_REFCLK = 1,
+	XHDMIPHY_SYSCLKSELOUT_QPLL0_REFCLK = 2,
+	XHDMIPHY_SYSCLKSELOUT_QPLL1_REFCLK = 3,
+	XHDMIPHY_SYSCLKSELOUT_PLL0_REFCLK = 0,
+	XHDMIPHY_SYSCLKSELOUT_PLL1_REFCLK = 1
+};
+
+enum outclk_sel {
+	XHDMIPHY_OUTCLKSEL_TYPE_OUTCLKPCS = 1,
+	XHDMIPHY_OUTCLKSEL_TYPE_OUTCLKPMA = 2,
+	XHDMIPHY_OUTCLKSEL_TYPE_PLLREFCLK_DIV1 = 3,
+	XHDMIPHY_OUTCLKSEL_TYPE_PLLREFCLK_DIV2 = 4,
+	XHDMIPHY_OUTCLKSEL_TYPE_PROGDIVCLK = 5
+};
+
+enum gt_state {
+	XHDMIPHY_GT_STATE_IDLE = 0,		/* idle state. */
+	XHDMIPHY_GT_STATE_GPO_RE = 1,	/* GPO RE state. */
+	XHDMIPHY_GT_STATE_LOCK = 2,		/* lock state. */
+	XHDMIPHY_GT_STATE_RESET = 3,	/* reset state. */
+	XHDMIPHY_GT_STATE_ALIGN = 4,	/* align state. */
+	XHDMIPHY_GT_STATE_READY = 5,	/* ready state. */
+};
+
+enum mmcm_divs {
+	XHDMIPHY_MMCM_CLKFBOUT_MULT_F = 0,	/* M */
+	XHDMIPHY_MMCM_DIVCLK_DIVIDE = 1,	/* D */
+	XHDMIPHY_MMCM_CLKOUT_DIVIDE = 2	/* On */
+};
+
+enum mmcmclk_insel {
+	XHDMIPHY_MMCM_CLKINSEL_CLKIN1 = 1,
+	XHDMIPHY_MMCM_CLKINSEL_CLKIN2 = 0,
+};
+
+enum tx_patgen {
+	XHDMIPHY_patgen_ratio_10 = 0x1,	/* LR:clock Ratio = 10 */
+	XHDMIPHY_patgen_ratio_20 = 0x2,	/* LR:clock Ratio = 20 */
+	XHDMIPHY_patgen_ratio_30 = 0x3,	/* LR:clock Ratio = 30 */
+	XHDMIPHY_patgen_ratio_40 = 0x4,	/* LR:clock Ratio = 40 */
+	XHDMIPHY_patgen_ratio_50 = 0x5,	/* LR:clock Ratio = 50 */
+};
+
+enum prbs_pat {
+	XHDMIPHY_PRBSSEL_STD_MODE = 0x0,	/* PCattern gen/mon OFF */
+	XHDMIPHY_PRBSSEL_PRBS7 = 0x1,		/* PCRBS-7 */
+	XHDMIPHY_PRBSSEL_PRBS9 = 0x2,		/* PCRBS-9 */
+	XHDMIPHY_PRBSSEL_PRBS15 = 0x3,		/* PCRBS-15 */
+	XHDMIPHY_PRBSSEL_PRBS23 = 0x4,		/* PCRBS-23 */
+	XHDMIPHY_PRBSSEL_PRBS31 = 0x5,		/* PRBS-31 */
+	XHDMIPHY_PRBSSEL_PCIE = 0x8,		/* PCIE compliance pattern */
+	XHDMIPHY_PRBSSEL_SQUARE_2UI = 0x9,	/* square wave with 2 UI */
+	XHDMIPHY_PRBSSEL_SQUARE_16UI = 0xA,	/* square wave with 16 UI */
+};
+
+enum xhdmiphy_mode {
+	tmds_mode = 0,
+	frl_mode = 1,
+};
+
+struct pll_param {
+	u8 m_refclk_div;
+	union {
+		u8 nfb_divs[2];
+		u8 nfb_div;
+		struct {
+			u8 n1fb_div;
+			u8 n2fb_div;
+		};
+	};
+	u16 cdr[5];
+	u8 is_lowerband;
+};
+
+struct channel {
+	u64 linerate;
+	union {
+		struct pll_param qpll_param;
+		struct pll_param cpll_param;
+		struct pll_param pll_param;
+		u16 linerate_cfg;
+	};
+	union {
+		enum refclk_sel cpll_refclk;
+		enum refclk_sel pll_refclk;
+	};
+	union {
+		struct {
+			u8 rx_outdiv;
+			u8 tx_outdiv;
+		};
+		u8 outdiv[2];
+	};
+	union {
+		struct {
+			enum gt_state rx_state;
+			enum gt_state tx_state;
+		};
+		enum gt_state gt_state[2];
+	};
+	union {
+		struct {
+			enum prot_type rx_protocol;
+			enum prot_type tx_protocol;
+		};
+		enum prot_type protocol[2];
+	};
+	union {
+		struct {
+			enum sysclk_data_sel rx_data_refclk;
+			enum sysclk_data_sel tx_data_refclk;
+		};
+		enum sysclk_data_sel data_refclk[2];
+	};
+	union {
+		struct {
+			enum sysclk_outsel rx_outrefclk;
+			enum sysclk_outsel tx_outrefclk;
+		};
+		enum sysclk_outsel out_refclk[2];
+	};
+	 union {
+		struct {
+			enum outclk_sel rx_outlck;
+			enum outclk_sel tx_outclk;
+		};
+		enum outclk_sel outclk_sel[2];
+	};
+	union {
+		struct {
+			u8 rx_dly_bypass;
+			u8 tx_dly_bypass;
+		};
+		u8 dly_bypass;
+	};
+
+	u8 rx_data_width;
+	u8 rx_intdata_width;
+	u8 tx_data_width;
+	u8 tx_intdata_width;
+};
+
+struct xhdmiphy_mmcm {
+	u32 index;
+	u16 clkfbout_mult;
+	u16 divclk_divide;
+	u16 clkout0_div;
+	u16 clkout1_div;
+	u16 clkout2_div;
+};
+
+struct quad {
+	union {
+		struct {
+			struct xhdmiphy_mmcm rx_mmcm;
+			struct xhdmiphy_mmcm tx_mmcm;
+		};
+		struct xhdmiphy_mmcm mmcm[2];
+	};
+	union {
+		struct {
+			struct channel ch1;
+			struct channel ch2;
+			struct channel ch3;
+			struct channel ch4;
+			union {
+				struct channel cmn0;
+				struct channel lcpll;
+			};
+			union {
+				struct channel cmn1;
+				struct channel rpll;
+			};
+		};
+		struct channel plls[6];
+	};
+	union {
+		struct {
+			u32 gt_refclk0;
+			u32 gt_refclk1;
+			u32 gt_nrefclk0;
+			u32 gt_nrefclk1;
+			u32 gt_srefclk0;
+			u32 gt_srefclk1;
+			u32 gt_grefclk;
+		};
+	u32 refclk[7];
+	};
+};
+
+struct hdmi21_cfg {
+	u64 linerate;
+	u8 nchannels;
+	u8 is_en;
+};
+
+struct clk_config {
+	int (*sel_mux)(u8 direction, u8 clksrc);
+	int (*set_linerate)(u8 direction, u8 mode, u64 lrate);
+};
+
+struct xhdmiphy_conf {
+	u8 tx_channels;
+	u8 rx_channels;
+	enum gt_type gt_type;
+	enum prot_type tx_protocol;
+	enum prot_type rx_protocol;
+	enum refclk_sel tx_refclk_sel;		/* tx refclk selection. */
+	enum refclk_sel rx_refclk_sel;		/* rx refclk selection. */
+	enum refclk_sel tx_frl_refclk_sel;	/* tx frl refclk selection. */
+	enum refclk_sel rx_frl_refclk_sel;	/* rx frl refclk selection. */
+	enum sysclk_data_sel tx_pllclk_sel;	/* tx sysclk selection. */
+	enum sysclk_data_sel rx_pllclk_sel;	/* rx sysclk selectino. */
+	u8 dru_present;
+	enum refclk_sel dru_refclk_sel;		/* DRU REFCLK selection. */
+	enum ppc ppc;
+	u8 tx_buff_bypass;
+	u8 fast_switch;
+	u8 transceiver_width;
+	u32 err_irq;		/* Error IRQ is enalbed in design */
+	u32 axilite_freq;
+	u32 drpclk_freq;
+	u8 gt_as_tx_tmdsclk;	/* use 4th GT channel as tx TMDS clock */
+	u8 rx_maxrate;
+	u8 tx_maxrate;
+};
+
+struct xhdmiphy_dev {
+	struct device *dev;
+	void __iomem *phy_base;
+	struct hdmiphy_callback phycb[TX_READY_CB];
+	int irq;
+	struct mutex hdmiphy_mutex;	/* protecting phy operations */
+	struct xhdmiphy_lane *lanes[4];
+	struct clk_config *data;
+	struct clk *axi_lite_clk;
+	struct clk *dru_clk;
+	struct clk *tmds_clk;
+	struct xhdmiphy_conf conf;
+	const struct gt_conf *gt_adp;
+	struct hdmi21_cfg tx_hdmi21_cfg;
+	struct hdmi21_cfg rx_hdmi21_cfg;
+	struct quad quad;
+	struct gpio_desc *rxch4_gpio;
+	u32 rx_refclk_hz;
+	u32 tx_refclk_hz;
+	u8 bpc;
+	u32 color_fmt;
+	u8 rx_tmdsclock_ratio;
+	u8 tx_samplerate;
+	u8 rx_dru_enabled;
+	u8 qpll_present;
+};
+
+void xhdmiphy_set_clr(struct xhdmiphy_dev *inst, u32 addr, u32 reg_val,
+		      u32 mask_val, u8 set_clr);
+void xhdmiphy_ch2ids(struct xhdmiphy_dev *inst, enum chid chid, u8 *id0,
+		     u8 *id1);
+u32 xhdmiphy_pll_cal(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir,
+		     u32 pllclk_infreq_hz);
+void xhdmiphy_write_refclksel(struct xhdmiphy_dev *inst);
+void xhdmiphy_pll_refclk_sel(struct xhdmiphy_dev *inst, enum chid chid,
+			     enum refclk_sel refclk_sel);
+void xhdmiphy_sysclk_data_sel(struct xhdmiphy_dev *inst, enum dir dir,
+			      enum sysclk_data_sel sysclk_datasel);
+void xhdmiphy_sysclk_out_sel(struct xhdmiphy_dev *inst, enum dir dir,
+			     enum sysclk_outsel sysclk_outsel);
+u32 xhdmiphy_get_quad_refclk(struct xhdmiphy_dev *inst,
+			     enum refclk_sel refclk_type);
+bool xhdmiphy_check_linerate_cfg(struct xhdmiphy_dev *inst, enum chid chid,
+				 enum dir dir);
+void xhdmiphy_set_gpi(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir,
+		      u8 set);
+u8 xhdmiphy_get_gpo(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir);
+void xhdmiphy_mmcm_reset(struct xhdmiphy_dev *inst, enum dir dir, u8 hold);
+void xhdmiphy_mmcm_lock_en(struct xhdmiphy_dev *inst, enum dir dir, u8 en);
+
+void xhdmiphy_set_bufgtdiv(struct xhdmiphy_dev *inst, enum dir dir, u8 div);
+void xhdmiphy_powerdown_gtpll(struct xhdmiphy_dev *inst, enum chid chid, u8 hold);
+
+void xhdmiphy_intr_en(struct xhdmiphy_dev *inst, u32 intr);
+void xhdmiphy_intr_dis(struct xhdmiphy_dev *inst, u32 intr);
+
+u64 xhdmiphy_get_pll_vco_freq(struct xhdmiphy_dev *inst, enum chid chid,
+			      enum dir dir);
+bool xhdmiphy_is_hdmi(struct xhdmiphy_dev *inst, enum dir dir);
+bool xhdmiphy_is_ch(enum chid chid);
+bool xhdmiphy_is_cmn(enum chid chid);
+bool xhdmiphy_is_using_qpll(struct xhdmiphy_dev *inst, enum chid chid,
+			    enum dir dir);
+u32 xhdmiphy_qpll_param(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir);
+u32 xhdmiphy_cpll_param(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir);
+
+void xhdmiphy_gt_handler(struct xhdmiphy_dev *inst, u32 event_ack, u32 event);
+void xhdmiphy_clkdet_handler(struct xhdmiphy_dev *inst, u32 event_ack, u32 event);
+void xhdmiphy_cfg_init(struct xhdmiphy_dev *inst);
+void xhdmiphy_pll_init(struct xhdmiphy_dev *inst, enum chid chid,
+		       enum refclk_sel qpll_refclk_sel,
+		       enum refclk_sel cpll_refclk_sel,
+		       enum pll_type txpll_sel, enum pll_type rxpll_sel);
+void xhdmiphy_cfg_linerate(struct xhdmiphy_dev *inst, enum chid chid,
+			   u64 linerate);
+u32 xhdmiphy_get_pll_type(struct xhdmiphy_dev *inst, enum dir dir,
+			  enum chid chid);
+u64 xhdmiphy_get_linerate(struct xhdmiphy_dev *inst, enum chid chid);
+void xhdmiphy_set_tx_vs(struct xhdmiphy_dev *inst, enum chid chid, u8 vs);
+void xhdmiphy_set_tx_pe(struct xhdmiphy_dev *inst, enum chid chid, u8 pe);
+void xhdmiphy_set_tx_pc(struct xhdmiphy_dev *inst, enum chid chid, u8 pc);
+void xhdmiphy_set_rxlpm(struct xhdmiphy_dev *inst, enum chid chid,
+			enum dir dir, u8 en);
+u32 xhdmiphy_drpwr(struct xhdmiphy_dev *inst, enum chid chid, u16 addr,
+		   u16 val);
+u32 xhdmiphy_drprd(struct xhdmiphy_dev *inst, enum chid chid, u16 addr,
+		   u16 *reg_val);
+void xhdmiphy_mmcm_pwr_down(struct xhdmiphy_dev *inst, enum dir dir, u8 hold);
+void xhdmiphy_mmcm_start(struct xhdmiphy_dev *inst, enum dir dir);
+void xhdmiphy_mmcm_param(struct xhdmiphy_dev *inst, enum dir dir);
+void xhdmiphy_ibufds_en(struct xhdmiphy_dev *inst, enum dir dir, u8 en);
+void xhdmiphy_clkout1_obuftds_en(struct xhdmiphy_dev *inst, enum dir dir, u8 en);
+void xhdmiphy_rst_gt_txrx(struct xhdmiphy_dev *inst, enum chid chid,
+			  enum dir dir, u8 hold);
+u32 xhdmiphy_init_phy(struct xhdmiphy_dev *inst);
+u32 xhdmiphy_set_tx_param(struct xhdmiphy_dev *inst, enum chid chid,
+			  enum ppc ppc, enum color_depth bpc,
+			  enum color_fmt fmt);
+u32 xhdmiphy_cal_mmcm_param(struct xhdmiphy_dev *inst, enum chid chid,
+			    enum dir dir, enum ppc ppc, enum color_depth bpc);
+u32 xhdmiphy_get_dru_refclk(struct xhdmiphy_dev *inst);
+void xhdmiphy_hdmi20_conf(struct xhdmiphy_dev *inst, enum dir dir);
+u32 xhdmiphy_hdmi21_conf(struct xhdmiphy_dev *inst, enum dir dir, u64 linerate, u8 nchannels);
+void xhdmiphy_clkdet_freq_reset(struct xhdmiphy_dev *inst, enum dir dir);
+u32 xhdmiphy_read(struct xhdmiphy_dev *inst, u32 addr);
+void xhdmiphy_write(struct xhdmiphy_dev *inst, u32 addr, u32 val);
+
+struct gtpll_divs {
+	const u8 *m;
+	const u8 *n1;
+	const u8 *n2;
+	const u8 *d;
+};
+
+struct gt_conf {
+	bool (*cfg_set_cdr)(struct xhdmiphy_dev *inst, enum chid);
+	bool (*check_pll_oprange)(struct xhdmiphy_dev *inst, enum chid,
+				  u64 pllclk_out_freq);
+	u32 (*outdiv_ch_reconf)(struct xhdmiphy_dev *inst, enum chid, enum dir);
+	u32 (*clk_ch_reconf)(struct xhdmiphy_dev *inst, enum chid);
+	u32 (*clk_cmn_reconf)(struct xhdmiphy_dev *inst, enum chid);
+	u32 (*rxch_reconf)(struct xhdmiphy_dev *inst, enum chid);
+	u32 (*txch_reconf)(struct xhdmiphy_dev *inst, enum chid);
+	struct gtpll_divs cpll_divs;
+	struct gtpll_divs qpll_divs;
+};
+
+u32 xhdmiphy_outdiv_ch_reconf(struct xhdmiphy_dev *instinst, enum chid chid,
+			      enum dir dir);
+u32 xhdmiphy_clk_ch_reconf(struct xhdmiphy_dev *instinst, enum chid chid);
+u32 xhdmiphy_clk_cmn_reconf(struct xhdmiphy_dev *instinst, enum chid chid);
+u32 xhdmiphy_rxch_reconf(struct xhdmiphy_dev *instinst, enum chid chid);
+u32 xhdmiphy_txch_reconf(struct xhdmiphy_dev *instinst, enum chid chid);
+
+extern const struct gt_conf gthe4_conf;
+extern const struct gt_conf gtye5_conf;
+#endif /* XHDMIPHY_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xhdmiphy_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xhdmiphy_core.c
@@ -0,0 +1,1108 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/iopoll.h>
+#include <linux/string.h>
+#include "xhdmiphy.h"
+
+u32 xhdmiphy_read(struct xhdmiphy_dev *inst, u32 addr)
+{
+	return ioread32(inst->phy_base + addr);
+}
+
+void xhdmiphy_write(struct xhdmiphy_dev *inst, u32 addr, u32 value)
+{
+	iowrite32(value, inst->phy_base + addr);
+}
+
+void xhdmiphy_set_clr(struct xhdmiphy_dev *inst, u32 addr, u32 reg_val,
+		      u32 mask_val, u8 set_clr)
+{
+	if (set_clr)
+		reg_val |= mask_val;
+	else
+		reg_val &= ~mask_val;
+
+	xhdmiphy_write(inst, addr, reg_val);
+}
+
+/**
+ * xhdmiphy_cfg_set_cdr - This function is a transceiver adaptor to set the
+ * clock and data recovery (CDR) values for a given channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel id to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static bool xhdmiphy_cfg_set_cdr(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	return inst->gt_adp->cfg_set_cdr(inst, chid);
+}
+
+/**
+ * xhdmiphy_check_pll_oprange - This function is a transceiver adaptor to check
+ * if a given PLL output frequency is within the operating range of the PLL for
+ * the GT type.
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance
+ * @chid:		chid is the channel ID to operate on
+ * @pllclk_out_freq:	pllclk_out_freq is the frequency to check
+ *
+ * @return:	- 0 if the frequency resides within the PLL's range
+ *		- 1 otherwise
+ */
+static bool xhdmiphy_check_pll_oprange(struct xhdmiphy_dev *inst, enum chid chid,
+				       u64 pllclk_out_freq)
+{
+	return inst->gt_adp->check_pll_oprange(inst, chid, pllclk_out_freq);
+}
+
+u32 xhdmiphy_outdiv_ch_reconf(struct xhdmiphy_dev *inst, enum chid chid,
+			      enum dir dir)
+{
+	return inst->gt_adp->outdiv_ch_reconf(inst, chid, dir);
+}
+
+u32 xhdmiphy_clk_ch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	return inst->gt_adp->clk_ch_reconf(inst, chid);
+}
+
+u32 xhdmiphy_clk_cmn_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	return inst->gt_adp->clk_cmn_reconf(inst, chid);
+}
+
+u32 xhdmiphy_rxch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	return inst->gt_adp->rxch_reconf(inst, chid);
+}
+
+u32 xhdmiphy_txch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	return inst->gt_adp->txch_reconf(inst, chid);
+}
+
+/**
+ * xhdmiphy_is_hdmi - This function checks if Instance is HDMI 2.0 or HDMI 2.1
+ *
+ * @inst:	inst is a pointer to the HDMIPHY instance
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:	true if HDMI 2.0 or 2.1 else false
+ */
+bool xhdmiphy_is_hdmi(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	if (dir == XHDMIPHY_DIR_TX) {
+		if (inst->conf.tx_protocol == XHDMIPHY_PROT_HDMI ||
+		    inst->conf.tx_protocol == XHDMIPHY_PROT_HDMI21)
+			return true;
+	} else {
+		if (inst->conf.rx_protocol == XHDMIPHY_PROT_HDMI ||
+		    inst->conf.rx_protocol == XHDMIPHY_PROT_HDMI21)
+			return true;
+	}
+
+	return false;
+}
+
+bool xhdmiphy_is_using_qpll(struct xhdmiphy_dev *inst, enum chid chid,
+			    enum dir dir)
+{
+	enum pll_type pll_type;
+
+	pll_type = xhdmiphy_get_pll_type(inst, dir, chid);
+
+	if (pll_type == XHDMIPHY_PLL_QPLL || pll_type == XHDMIPHY_PLL_QPLL0 ||
+	    pll_type == XHDMIPHY_PLL_QPLL1)
+		return 1;
+
+	return 0;
+}
+
+bool xhdmiphy_is_cmn(enum chid chid)
+{
+	return (chid == XHDMIPHY_CHID_CMNA ||
+		(chid >= XHDMIPHY_CHID_CMN0 &&
+		chid <= XHDMIPHY_CHID_CMN1));
+}
+
+bool xhdmiphy_is_ch(enum chid chid)
+{
+	return (chid == XHDMIPHY_CHID_CHA ||
+		(chid >= XHDMIPHY_CHID_CH1 &&
+		chid <= XHDMIPHY_CHID_CH4));
+}
+
+/**
+ * xhdmiphy_ch2ids - This function will set the channel id's to correspond with
+ * the supplied channel ID based on the protocol. HDMI uses 3 channels; This ID
+ * translation is done to allow other functions to operate iteratively over
+ * multiple channels.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID used to determine the indices
+ * @id0:	Id0 is a pointer to the start channel ID to set
+ * @id1:	Id1 is a pointer to the end channel ID to set
+ */
+void xhdmiphy_ch2ids(struct xhdmiphy_dev *inst, enum chid chid, u8 *id0,
+		     u8 *id1)
+{
+	u8 channels;
+
+	if (chid == XHDMIPHY_CHID_CHA) {
+		*id0 = XHDMIPHY_CHID_CH1;
+		if ((xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX)) ||
+		    (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX))) {
+			if (inst->conf.tx_protocol == XHDMIPHY_PROT_HDMI21 ||
+			    inst->conf.rx_protocol == XHDMIPHY_PROT_HDMI21)
+				*id1 = XHDMIPHY_CHID_CH4;
+			else if ((inst->conf.tx_protocol == XHDMIPHY_PROT_HDMI) &&
+				 inst->conf.gt_as_tx_tmdsclk)
+				*id1 = XHDMIPHY_CHID_CH4;
+			else
+				*id1 = XHDMIPHY_CHID_CH3;
+
+		} else {
+			channels = ((inst->conf.tx_channels >=
+				inst->conf.rx_channels) ?
+				inst->conf.tx_channels :
+				inst->conf.rx_channels);
+
+			if (channels == 1)
+				*id1 = XHDMIPHY_CHID_CH1;
+			else if (channels == 2)
+				*id1 = XHDMIPHY_CHID_CH2;
+			else if (channels == 3)
+				*id1 = XHDMIPHY_CHID_CH3;
+			else
+				*id1 = XHDMIPHY_CHID_CH4;
+		}
+	} else if (chid == XHDMIPHY_CHID_CMNA) {
+		*id0 = XHDMIPHY_CHID_CMN0;
+		if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTHE4 ||
+		    inst->conf.gt_type == XHDMIPHY_GTTYPE_GTYE4)
+			*id1 = XHDMIPHY_CHID_CMN1;
+		else
+			*id1 = XHDMIPHY_CHID_CMN0;
+	} else {
+		*id0 = *id1 = chid;
+	}
+}
+
+/**
+ * xhdmiphy_pll_refclk_sel - configure the PLL reference clock selection for the
+ * specified channel(s). This is applied to both direction to the software
+ * configuration only.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @refclk_sel:	refclk_sel is the reference clock selection to configure
+ */
+void xhdmiphy_pll_refclk_sel(struct xhdmiphy_dev *inst, enum chid chid,
+			     enum refclk_sel refclk_sel)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].pll_refclk = refclk_sel;
+}
+
+/**
+ * xhdmiphy_sysclk_data_sel - configure the SYSCLKDATA reference clock
+ * selection for the direction. Same configuration applies to all channels in
+ * the quad. This is applied to the software configuration only.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @sys_clk_data_sel: sys_clk_data_sel is reference clock selection to configure
+ */
+void xhdmiphy_sysclk_data_sel(struct xhdmiphy_dev *inst, enum dir dir,
+			      enum sysclk_data_sel sys_clk_data_sel)
+{
+	struct channel *ch_ptr;
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+
+	/* select in software - same for all channels */
+	for (id = id0; id <= id1; id++) {
+		ch_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(id)];
+		ch_ptr->data_refclk[dir] = sys_clk_data_sel;
+	}
+}
+
+/**
+ * xhdmiphy_sysclk_out_sel - configure the SYSCLKOUT reference clock selection
+ * for the direction. Same configuration applies to all channels in the quad.
+ * This is applied to the software configuration only.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @sys_clkout_sel:	sys_clkout_sel is reference clock selection to configure
+ */
+void xhdmiphy_sysclk_out_sel(struct xhdmiphy_dev *inst, enum dir dir,
+			     enum sysclk_outsel sys_clkout_sel)
+{
+	struct channel *ch_ptr;
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+
+	/* select in software - same for all channels */
+	for (id = id0; id <= id1; id++) {
+		ch_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(id)];
+		ch_ptr->out_refclk[dir] = sys_clkout_sel;
+	}
+}
+
+void xhdmiphy_cfg_init(struct xhdmiphy_dev *inst)
+{
+	u8 sel;
+
+	if (inst->conf.gt_type == XHDMIPHY_GTHE4)
+		inst->gt_adp = &gthe4_conf;
+	else if (inst->conf.gt_type == XHDMIPHY_GTYE5)
+		inst->gt_adp = &gtye5_conf;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		const enum sysclk_data_sel sysclk[7][2] = {
+			{0, XHDMIPHY_SYSCLKSELDATA_CPLL_OUTCLK},
+			{1, XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK},
+			{2, XHDMIPHY_SYSCLKSELDATA_QPLL1_OUTCLK},
+			{3, XHDMIPHY_SYSCLKSELDATA_QPLL_OUTCLK},
+			{4, XHDMIPHY_SYSCLKSELDATA_PLL0_OUTCLK},
+			{5, XHDMIPHY_SYSCLKSELDATA_PLL1_OUTCLK},
+			{6, XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK},
+		};
+
+		for (sel = 0; sel < 7; sel++) {
+			if (inst->conf.tx_pllclk_sel == sysclk[sel][0])
+				inst->conf.tx_pllclk_sel = sysclk[sel][1];
+			if (inst->conf.rx_pllclk_sel == sysclk[sel][0])
+				inst->conf.rx_pllclk_sel = sysclk[sel][1];
+		}
+
+		inst->conf.tx_refclk_sel = inst->conf.tx_refclk_sel +
+					   XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0;
+		inst->conf.rx_refclk_sel = inst->conf.rx_refclk_sel +
+					   XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0;
+		inst->conf.tx_frl_refclk_sel = inst->conf.tx_frl_refclk_sel +
+					       XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0;
+		inst->conf.rx_frl_refclk_sel = inst->conf.rx_frl_refclk_sel +
+					       XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0;
+		inst->conf.dru_refclk_sel = inst->conf.dru_refclk_sel +
+					    XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0;
+	}
+}
+
+static unsigned int xhdmiphy_pll2sysclk_data(enum pll_type pll_sel)
+{
+	if (pll_sel == XHDMIPHY_PLL_CPLL)
+		return XHDMIPHY_SYSCLKSELDATA_CPLL_OUTCLK;
+	else if (pll_sel == XHDMIPHY_PLL_QPLL)
+		return XHDMIPHY_SYSCLKSELDATA_QPLL_OUTCLK;
+	else if (pll_sel == XHDMIPHY_PLL_QPLL0)
+		return XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK;
+
+	return XHDMIPHY_SYSCLKSELDATA_QPLL1_OUTCLK;
+}
+
+static unsigned short xhdmiphy_pll2sysclk_out(enum pll_type pll_sel)
+{
+	if (pll_sel == XHDMIPHY_PLL_CPLL)
+		return XHDMIPHY_SYSCLKSELOUT_CPLL_REFCLK;
+	else if (pll_sel == XHDMIPHY_PLL_QPLL)
+		return XHDMIPHY_SYSCLKSELOUT_QPLL_REFCLK;
+	else if (pll_sel == XHDMIPHY_PLL_QPLL0)
+		return XHDMIPHY_SYSCLKSELOUT_QPLL0_REFCLK;
+
+	return XHDMIPHY_SYSCLKSELOUT_QPLL1_REFCLK;
+}
+
+void xhdmiphy_write_refclksel(struct xhdmiphy_dev *inst)
+{
+	struct channel *ch_ptr;
+	enum gt_type gt_type = inst->conf.gt_type;
+	u32 reg_val = 0;
+
+	/* point to the first channel since settings apply to all channels */
+	ch_ptr = &inst->quad.ch1;
+
+	/* pll_refclk */
+	reg_val &= ~XHDMIPHY_REFCLKSEL_QPLL0_MASK;
+	reg_val = inst->quad.cmn0.pll_refclk;
+
+	reg_val &= ~XHDMIPHY_REFCLKSEL_CPLL_MASK;
+	reg_val |= (ch_ptr->cpll_refclk << XHDMIPHY_REFCLKSEL_CPLL_SHIFT);
+	if (gt_type == XHDMIPHY_GTTYPE_GTHE4 ||
+	    gt_type == XHDMIPHY_GTTYPE_GTYE4) {
+		reg_val &= ~XHDMIPHY_REFCLKSEL_QPLL1_MASK;
+		reg_val |= (inst->quad.cmn1.pll_refclk <<
+				XHDMIPHY_REFCLKSEL_QPLL1_SHIFT);
+	}
+
+	/* sys_clk_data_sel. PLLCLKSEL */
+	reg_val &= ~XHDMIPHY_REFCLKSEL_SYSCLKSEL_MASK;
+	/* TXSYSCLKSEL[0].TXPLLCLKSEL */
+	reg_val |= (ch_ptr->tx_data_refclk <<
+		    XHDMIPHY_TXSYSCLKSEL_DATA_SHIFT(gt_type)) &
+		   XHDMIPHY_TXSYSCLKSEL_DATA_MASK(gt_type);
+
+	/* RXSYSCLKSEL[0].RXPLLCLKSEL */
+	reg_val |= (ch_ptr->rx_data_refclk <<
+		    XHDMIPHY_RXSYSCLKSEL_DATA_SHIFT(gt_type)) &
+		   XHDMIPHY_RXSYSCLKSEL_DATA_MASK(gt_type);
+
+	/* sys_clkout_sel */
+	reg_val |= (ch_ptr->tx_outrefclk <<
+		    XHDMIPHY_TXSYSCLKSEL_OUT_SHIFT(gt_type)) &
+		   XHDMIPHY_TXSYSCLKSEL_OUT_MASK(gt_type);
+
+	reg_val |= (ch_ptr->rx_outrefclk <<
+		    XHDMIPHY_RXSYSCLKSEL_OUT_SHIFT(gt_type)) &
+		   XHDMIPHY_RXSYSCLKSEL_OUT_MASK(gt_type);
+
+	xhdmiphy_write(inst, XHDMIPHY_REFCLKSEL_REG, reg_val);
+}
+
+/**
+ * xhdmiphy_pll_init - This function will initialize the PLL selection for a
+ * given channel.
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance
+ * @chid:		chid is the channel ID to operate on
+ * @qpll_refclk_sel:	qpll_refclk_sel is the QPLL reference clock selection
+ *			for the quad
+ * @cpll_refclk_sel:	cpll_refclk_sel is the CPLL reference clock selection
+ *			for the quad
+ * @txpll_sel:		txpll_sel is the reference clock selection for the
+ *			quad's TX PLL dividers
+ * @rxpll_sel:		rxpll_sel is the reference clock selection for the
+ *			quad's RX PLL dividers
+ */
+void xhdmiphy_pll_init(struct xhdmiphy_dev *inst, enum chid chid,
+		       enum refclk_sel qpll_refclk_sel,
+		       enum refclk_sel cpll_refclk_sel,
+		       enum pll_type txpll_sel, enum pll_type rxpll_sel)
+{
+	xhdmiphy_pll_refclk_sel(inst, XHDMIPHY_CHID_CMNA, qpll_refclk_sel);
+	xhdmiphy_pll_refclk_sel(inst, XHDMIPHY_CHID_CHA, cpll_refclk_sel);
+	xhdmiphy_sysclk_data_sel(inst, XHDMIPHY_DIR_TX,
+				 xhdmiphy_pll2sysclk_data(txpll_sel));
+	xhdmiphy_sysclk_data_sel(inst, XHDMIPHY_DIR_RX,
+				 xhdmiphy_pll2sysclk_data(rxpll_sel));
+	xhdmiphy_sysclk_out_sel(inst, XHDMIPHY_DIR_TX,
+				xhdmiphy_pll2sysclk_out(txpll_sel));
+	xhdmiphy_sysclk_out_sel(inst, XHDMIPHY_DIR_RX,
+				xhdmiphy_pll2sysclk_out(rxpll_sel));
+
+	xhdmiphy_write_refclksel(inst);
+}
+
+/**
+ * xhdmiphy_cfg_linerate - confure the channel's line rate. This is a software
+ * only configuration and this value is used in the PLL calculator.
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance
+ * @chid:		chid is the channel ID to operate on
+ * @linkrate_freq:	LineRate is the line rate to configure software
+ */
+void xhdmiphy_cfg_linerate(struct xhdmiphy_dev *inst, enum chid chid,
+			   u64 linkrate_freq)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].linerate = linkrate_freq;
+}
+
+/**
+ * xhdmiphy_get_sysclk_datasel - obtain the current [RT]XSYSCLKSEL[0]
+ * configuration.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance.
+ * @dir:	dir is an indicator for TX or RX
+ * @chid:	chId is the channel ID which to operate on
+ *
+ * @return:	The current [RT]XSYSCLKSEL[0] selection
+ */
+static unsigned int xhdmiphy_get_sysclk_datasel(struct xhdmiphy_dev *inst,
+						enum dir dir, enum chid chid)
+{
+	u32 sel, reg_val, gt_type;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_REFCLKSEL_REG);
+	gt_type = inst->conf.gt_type;
+
+	/* synchronize software configuration to hardware */
+	if (dir == XHDMIPHY_DIR_TX) {
+		sel = reg_val & XHDMIPHY_TXSYSCLKSEL_DATA_MASK(gt_type);
+		sel >>= XHDMIPHY_TXSYSCLKSEL_DATA_SHIFT(gt_type);
+	} else {
+		sel = reg_val & XHDMIPHY_RXSYSCLKSEL_DATA_MASK(gt_type);
+		sel >>= XHDMIPHY_RXSYSCLKSEL_DATA_SHIFT(gt_type);
+	}
+
+	return sel;
+}
+
+/**
+ * xhdmiphy_get_sysclk_outsel - obtain the current [RT]XSYSCLKSEL[1]
+ * configuration.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @chid:	chid is the channel ID which to operate on
+ *
+ * @return:	The current [RT]XSYSCLKSEL[1] selection
+ */
+static u32 xhdmiphy_get_sysclk_outsel(struct xhdmiphy_dev *inst,
+				      enum dir dir, enum chid chid)
+{
+	u32 sel, reg_val, gt_type;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_REFCLKSEL_REG);
+	gt_type = inst->conf.gt_type;
+
+	/* synchronize software configuration to hardware */
+	if (dir == XHDMIPHY_DIR_TX) {
+		sel = reg_val & XHDMIPHY_TXSYSCLKSEL_OUT_MASK(gt_type);
+		sel >>= XHDMIPHY_TXSYSCLKSEL_OUT_SHIFT(gt_type);
+	} else {
+		sel = reg_val & XHDMIPHY_RXSYSCLKSEL_OUT_MASK(gt_type);
+		sel >>= XHDMIPHY_RXSYSCLKSEL_OUT_SHIFT(gt_type);
+	}
+
+	return sel;
+}
+
+/**
+ * xhdmiphy_get_pll_type - obtain the channel's PLL reference clock selection.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @chid:	chid is the channel ID which to operate on
+ *
+ * @return:	The PLL type being used by the channel
+ */
+u32 xhdmiphy_get_pll_type(struct xhdmiphy_dev *inst, enum dir dir,
+			  enum chid chid)
+{
+	enum pll_type pll_type;
+	enum sysclk_data_sel sysclk_data_sel;
+	enum sysclk_outsel sysclk_out_sel;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		sysclk_data_sel = xhdmiphy_get_sysclk_datasel(inst, dir, chid);
+		sysclk_out_sel = xhdmiphy_get_sysclk_outsel(inst, dir, chid);
+
+		if (sysclk_data_sel == XHDMIPHY_SYSCLKSELDATA_CPLL_OUTCLK &&
+		    sysclk_out_sel == XHDMIPHY_SYSCLKSELOUT_CPLL_REFCLK)
+			pll_type = XHDMIPHY_PLL_CPLL;
+		else if ((sysclk_data_sel == XHDMIPHY_SYSCLKSELDATA_QPLL_OUTCLK) &&
+			 (sysclk_out_sel == XHDMIPHY_SYSCLKSELOUT_QPLL_REFCLK))
+			pll_type = XHDMIPHY_PLL_QPLL;
+		else if ((sysclk_data_sel == XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK) &&
+			 (sysclk_out_sel == XHDMIPHY_SYSCLKSELOUT_QPLL0_REFCLK))
+			pll_type = XHDMIPHY_PLL_QPLL0;
+		else if ((sysclk_data_sel == XHDMIPHY_SYSCLKSELDATA_QPLL1_OUTCLK) &&
+			 (sysclk_out_sel == XHDMIPHY_SYSCLKSELOUT_QPLL1_REFCLK))
+			pll_type = XHDMIPHY_PLL_QPLL1;
+		else
+			pll_type = XHDMIPHY_PLL_UNKNOWN;
+
+	} else {
+		if (dir == XHDMIPHY_DIR_TX)
+			pll_type = inst->conf.tx_pllclk_sel - 2;
+		else if (dir == XHDMIPHY_DIR_RX)
+			pll_type = inst->conf.rx_pllclk_sel - 2;
+		else
+			pll_type = XHDMIPHY_PLL_UNKNOWN;
+	}
+
+	return pll_type;
+}
+
+u64 xhdmiphy_get_linerate(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	enum chid ch_id = chid;
+
+	if (chid == XHDMIPHY_CHID_CHA)
+		ch_id = XHDMIPHY_CHID_CH1;
+	else if (chid == XHDMIPHY_CHID_CMNA)
+		ch_id = XHDMIPHY_CHID_CMN0;
+
+	return inst->quad.plls[ch_id - XHDMIPHY_CHID_CH1].linerate;
+}
+
+/**
+ * xhdmiphy_set_tx_vs - This function will set the TX voltage swing value for
+ * a given channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @vs:		vs is the voltage swing value to write
+ */
+void xhdmiphy_set_tx_vs(struct xhdmiphy_dev *inst, enum chid chid, u8 vs)
+{
+	u32 reg_val, mask_val, reg_off;
+
+	if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+		reg_off = XHDMIPHY_TX_DRIVER_CH12_REG;
+	else
+		reg_off = XHDMIPHY_TX_DRIVER_CH34_REG;
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+	mask_val = XHDMIPHY_TX_DRIVER_TXDIFFCTRL_MASK(chid);
+
+	reg_val &= ~mask_val;
+	reg_val |= ((vs & XHDMIPHY_TX_TXDIFFCTRL_MASK) <<
+		    XHDMIPHY_TX_DRIVER_TXDIFFCTRL_SHIFT(chid));
+	xhdmiphy_write(inst, reg_off, reg_val);
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_TX_DRIVER_EXT_REG);
+	mask_val = XHDMIPHY_TX_DRIVER_EXT_TXDIFFCTRL_MASK(chid);
+
+	reg_val &= ~mask_val;
+	reg_val |= ((vs & XHDMIPHY_TX_EXT_TXDIFFCTRL_MASK) <<
+		    XHDMIPHY_TX_DRIVER_EXT_TXDIFFCTRL_SHIFT(chid));
+
+	xhdmiphy_write(inst, XHDMIPHY_TX_DRIVER_EXT_REG, reg_val);
+}
+
+/**
+ * xhdmiphy_set_tx_pe - This function will set the TX pre-emphasis value for
+ * a given channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @pe:		pe is the pre-emphasis value to write
+ */
+void xhdmiphy_set_tx_pe(struct xhdmiphy_dev *inst, enum chid chid, u8 pe)
+{
+	u32 reg_val, mask_val, reg_off;
+
+	if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+		reg_off = XHDMIPHY_TX_DRIVER_CH12_REG;
+	else
+		reg_off = XHDMIPHY_TX_DRIVER_CH34_REG;
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+
+	mask_val = XHDMIPHY_TX_DRIVER_TXPRECURSOR_MASK(chid);
+	reg_val &= ~mask_val;
+	reg_val |= (pe << XHDMIPHY_TX_DRIVER_TXPRECURSOR_SHIFT(chid));
+	xhdmiphy_write(inst, reg_off, reg_val);
+}
+
+/**
+ * xhdmiphy_set_tx_pc - This function will set the TX post-curosr value for a
+ * given channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @pc:		pc is the post-curosr value to write
+ */
+void xhdmiphy_set_tx_pc(struct xhdmiphy_dev *inst, enum chid chid, u8 pc)
+{
+	u32 reg_val, mask_val, reg_off;
+
+	if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+		reg_off = XHDMIPHY_TX_DRIVER_CH12_REG;
+	else
+		reg_off = XHDMIPHY_TX_DRIVER_CH34_REG;
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+
+	mask_val = XHDMIPHY_TX_DRIVER_TXPOSTCURSOR_MASK(chid);
+	reg_val &= ~mask_val;
+	reg_val |= (pc << XHDMIPHY_TX_DRIVER_TXPOSTCURSOR_SHIFT(chid));
+	xhdmiphy_write(inst, reg_off, reg_val);
+}
+
+void xhdmiphy_set_rxlpm(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir,
+			u8 enable)
+{
+	u32 reg_val, mask_val;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_RX_EQ_CDR_REG);
+
+	if (chid == XHDMIPHY_CHID_CHA)
+		mask_val = XHDMIPHY_RX_CONTROL_RXLPMEN_ALL_MASK;
+	else
+		mask_val = XHDMIPHY_RX_CONTROL_RXLPMEN_MASK(chid);
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_RX_EQ_CDR_REG, reg_val, mask_val,
+			 enable);
+}
+
+static unsigned int xhdmiphy_drp_access(struct xhdmiphy_dev *inst,
+					enum chid chid, enum dir dir, u16 addr,
+					u16 *val)
+{
+	u32 reg_off_ctrl, reg_off_sts, reg_val, err;
+
+	/* determine which DRP registers to use based on channel */
+	if (xhdmiphy_is_cmn(chid)) {
+		reg_off_ctrl = XHDMIPHY_DRP_CONTROL_COMMON_REG;
+		reg_off_sts = XHDMIPHY_DRP_STATUS_COMMON_REG;
+	} else if (XHDMIPHY_ISTXMMCM(chid)) {
+		reg_off_ctrl = XHDMIPHY_DRP_CONTROL_TXMMCM_REG;
+		reg_off_sts = XHDMIPHY_DRP_STATUS_TXMMCM_REG;
+	} else if (XHDMIPHY_ISRXMMCM(chid)) {
+		reg_off_ctrl = XHDMIPHY_DRP_CONTROL_RXMMCM_REG;
+		reg_off_sts = XHDMIPHY_DRP_STATUS_RXMMCM_REG;
+	} else {
+		reg_off_ctrl = XHDMIPHY_DRP_CONTROL_CH1_REG +
+			(4 * XHDMIPHY_CH2IDX(chid));
+		reg_off_sts = XHDMIPHY_DRP_STATUS_CH1_REG +
+			(4 * (XHDMIPHY_CH2IDX(chid)));
+	}
+
+	err = readl_poll_timeout(inst->phy_base + reg_off_sts, reg_val,
+				 !(reg_val & XHDMIPHY_DRP_STATUS_DRPBUSY_MASK),
+				 1, 100);
+	if (err == -ETIMEDOUT) {
+		dev_err(inst->dev, "drp busy timeout\n");
+		return err;
+	}
+
+	/* write the command to the channel's DRP */
+	reg_val = (addr & XHDMIPHY_DRP_CONTROL_DRPADDR_MASK);
+	reg_val |= XHDMIPHY_DRP_CONTROL_DRPEN_MASK;
+	if (dir == XHDMIPHY_DIR_TX) {
+		reg_val |= XHDMIPHY_DRP_CONTROL_DRPWE_MASK;
+		reg_val |= ((*val << XHDMIPHY_DRP_CONTROL_DRPDI_SHIFT) &
+			    XHDMIPHY_DRP_CONTROL_DRPDI_MASK);
+	}
+	xhdmiphy_write(inst, reg_off_ctrl, reg_val);
+
+	err = readl_poll_timeout(inst->phy_base + reg_off_sts, reg_val,
+				 (reg_val & XHDMIPHY_DRP_STATUS_DRPRDY_MASK),
+				 1, 100);
+	if (err == -ETIMEDOUT) {
+		dev_err(inst->dev, "drp ready timeout\n");
+		return err;
+	}
+
+	if (dir == XHDMIPHY_DIR_RX) {
+		reg_val &= XHDMIPHY_DRP_STATUS_DRPO_MASK;
+		*val = reg_val;
+	}
+
+	return 0;
+}
+
+/**
+ * xhdmiphy_drpwr - This function will initiate a write drp transaction. It is
+ * a wrapper around xhdmiphy_drp_access.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel id on which to direct the DRP access
+ * @addr:	Addr is the DRP address to issue the DRP access to
+ * @val:	val is the value to write to the DRP address
+ *
+ * @return:	- 0 if the DRP access was successful
+ *		- -ETIMEDOUT otherwise, if the busy bit did not go low, or if
+ *			the ready bit did not go high
+ */
+u32 xhdmiphy_drpwr(struct xhdmiphy_dev *inst, enum chid chid, u16 addr, u16 val)
+{
+	return xhdmiphy_drp_access(inst, chid, XHDMIPHY_DIR_TX, addr, &val);
+}
+
+/**
+ * xhdmiphy_drprd - This function will initiate a read DRP transaction. It is
+ * a wrapper around xhdmiphy_drp_access.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID on which to direct the DRP access
+ * @addr:	addr is the DRP address to issue the DRP access to
+ * @ret_val:	ret_val is the DRP read_value returned implicitly
+ *
+ * @return:	- 0 if the DRP access was successful
+ *		- -ETIMEDOUT otherwise, if the busy bit did not go low, or if
+ *		the ready bit did not go high
+ */
+u32 xhdmiphy_drprd(struct xhdmiphy_dev *inst, enum chid chid, u16 addr,
+		   u16 *ret_val)
+{
+	return xhdmiphy_drp_access(inst, chid, XHDMIPHY_DIR_RX, addr, ret_val);
+}
+
+void xhdmiphy_ibufds_en(struct xhdmiphy_dev *inst, enum dir dir, u8 enable)
+{
+	enum refclk_sel *type_ptr, *dru_typ_ptr, dru_type_dummy;
+	u32 reg_val, reg_addr, mask_val = 0;
+
+	dru_type_dummy = XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK;
+	dru_typ_ptr = &dru_type_dummy;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		if (dir == XHDMIPHY_DIR_TX) {
+			type_ptr = &inst->conf.tx_refclk_sel;
+		} else {
+			type_ptr = &inst->conf.rx_refclk_sel;
+			if (inst->conf.dru_present)
+				dru_typ_ptr = &inst->conf.dru_refclk_sel;
+		}
+
+		if ((*type_ptr == XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0) ||
+		    (inst->conf.dru_present &&
+		     (*dru_typ_ptr == XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0))) {
+			mask_val = XHDMIPHY_IBUFDS_GTXX_CTRL_GTREFCLK0_CEB_MASK;
+		} else if ((*type_ptr == XHDMIPHY_PLL_REFCLKSEL_GTREFCLK1) ||
+			   (inst->conf.dru_present &&
+			    (*dru_typ_ptr == XHDMIPHY_PLL_REFCLKSEL_GTREFCLK1))) {
+			mask_val = XHDMIPHY_IBUFDS_GTXX_CTRL_GTREFCLK1_CEB_MASK;
+		}
+	}
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_addr = XHDMIPHY_MISC_TXUSRCLK_REG;
+	else
+		reg_addr = XHDMIPHY_MISC_RXUSRCLK_REG;
+
+	mask_val = XHDMIPHY_MISC_XXUSRCLK_REFCLK_CEB_MASK;
+	reg_val = xhdmiphy_read(inst, reg_addr);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+		xhdmiphy_set_clr(inst, reg_addr, reg_val, mask_val, !enable);
+	else
+		xhdmiphy_set_clr(inst, reg_addr, reg_val, mask_val, enable);
+}
+
+/**
+ * xhdmiphy_clkout1_obuftds_en - This function enables the tx or rx clkout1
+ * obuftds peripheral.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @enable:	enable specifies true/false value to either enable or disable
+ *		the obuftds, respectively
+ */
+void xhdmiphy_clkout1_obuftds_en(struct xhdmiphy_dev *inst, enum dir dir,
+				 u8 enable)
+{
+	u32 reg_val, reg_off, mask;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_MISC_TXUSRCLK_REG;
+	else
+		reg_off = XHDMIPHY_MISC_RXUSRCLK_REG;
+
+	/* read XXUSRCLK MISC register */
+	reg_val = xhdmiphy_read(inst, reg_off);
+	mask = XHDMIPHY_MISC_XXUSRCLK_CKOUT1_OEN_MASK;
+	/* write new value to XXUSRCLK MISC register */
+	xhdmiphy_set_clr(inst, reg_off, reg_val, mask, enable);
+}
+
+/**
+ * xhdmiphy_get_quad_refclk - obtain the current reference clock frequency for
+ * the quad based on the reference clock type.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @refclk_type:	refclk_type is the type to obtain the clock selection for
+ *
+ * @return:	The current reference clock frequency for the quad for the
+ *		specified type selection
+ */
+u32 xhdmiphy_get_quad_refclk(struct xhdmiphy_dev *inst,
+			     enum refclk_sel refclk_type)
+{
+	u32 freq;
+	u8 index = refclk_type - XHDMIPHY_PLL_REFCLKSEL_GTREFCLK0;
+
+	freq = (refclk_type > XHDMIPHY_PLL_REFCLKSEL_GTGREFCLK) ? 0 :
+		inst->quad.refclk[index];
+
+	return freq;
+}
+
+/**
+ * xhdmiphy_set_gpi - This function will set the GPI ports to the GT Wizard
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for TX or RX
+ * @set:	set Set=true; Clear=false
+ */
+void xhdmiphy_set_gpi(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir,
+		      u8 set)
+{
+	u32 reg_val, mask_val = 0;
+	u8 id, id0, id1;
+
+	/* read GPI register */
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_GT_DBG_GPI_REG);
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		if (dir == XHDMIPHY_DIR_TX)
+			mask_val |= XHDMIPHY_TX_GPI_MASK(id);
+		else
+			mask_val |= XHDMIPHY_RX_GPI_MASK(id);
+	}
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_GT_DBG_GPI_REG, reg_val, mask_val, set);
+}
+
+/**
+ * xhdmiphy_get_gpo - This function will get the GPO ports value from the GT
+ * Wizard
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for TX or RX
+ *
+ * @return:	- This will return the GPO port value.
+ */
+u8 xhdmiphy_get_gpo(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir)
+{
+	u32 reg_val;
+
+	/* Read GPI register */
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_GT_DBG_GPO_REG);
+
+	if (dir == XHDMIPHY_DIR_TX) {
+		return ((reg_val &
+			XHDMIPHY_TX_GPO_MASK_ALL(inst->conf.tx_channels)) >>
+			XHDMIPHY_TX_GPO_SHIFT);
+	}
+
+	return ((reg_val &
+		XHDMIPHY_RX_GPO_MASK_ALL(inst->conf.rx_channels)) >>
+		XHDMIPHY_RX_GPO_SHIFT);
+}
+
+/**
+ * xhdmiphy_set_bufgtdiv - This function obtains the divider value of the
+ * BUFG_GT peripheral.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @div:	div 3-bit divider value
+ */
+void xhdmiphy_set_bufgtdiv(struct xhdmiphy_dev *inst, enum dir dir, u8 div)
+{
+	u32 reg_val, reg_off;
+
+	if (div == 0)
+		div = 1;
+	else
+		div = div - 1;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_BUFGGT_TXUSRCLK_REG;
+	else
+		reg_off = XHDMIPHY_BUFGGT_RXUSRCLK_REG;
+
+	/* read BUFG_GT register */
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val &= ~XHDMIPHY_BUFGGT_XXUSRCLK_DIV_MASK;
+
+	/* shift divider value to correct position */
+	div <<= XHDMIPHY_BUFGGT_XXUSRCLK_DIV_SHIFT;
+	div &= XHDMIPHY_BUFGGT_XXUSRCLK_DIV_MASK;
+	reg_val |= div;
+
+	/* write new value to BUFG_GT ctrl register */
+	xhdmiphy_write(inst, reg_off, reg_val);
+}
+
+/**
+ * xhdmiphy_powerdown_gtpll - This function will power down the specified GT PLL.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to power down the PLL for
+ * @hold:	hold is an indicator whether to "hold" the power down if set
+ *		to 1. If set to 0: power down, then power back up
+ */
+void xhdmiphy_powerdown_gtpll(struct xhdmiphy_dev *inst, enum chid chid, u8 hold)
+{
+	u32 mask_val = 0, reg_val;
+	u8 id, id0, id1;
+
+	if (xhdmiphy_is_ch(chid))
+		xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	else
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+
+	for (id = id0; id <= id1; id++) {
+		if (chid == XHDMIPHY_CHID_CMN0) {
+			mask_val |= XHDMIPHY_POWERDOWN_CONTROL_QPLL0PD_MASK(id);
+		} else if (chid == XHDMIPHY_CHID_CMN1) {
+			mask_val |= XHDMIPHY_POWERDOWN_CONTROL_QPLL1PD_MASK(id);
+		} else if (chid == XHDMIPHY_CHID_CMNA) {
+			mask_val |= XHDMIPHY_POWERDOWN_CONTROL_QPLL0PD_MASK(id) |
+				   XHDMIPHY_POWERDOWN_CONTROL_QPLL1PD_MASK(id);
+		} else {
+			mask_val |= XHDMIPHY_POWERDOWN_CONTROL_CPLLPD_MASK(id);
+		}
+	}
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_POWERDOWN_CONTROL_REG);
+	reg_val |= mask_val;
+	xhdmiphy_write(inst, XHDMIPHY_POWERDOWN_CONTROL_REG, reg_val);
+
+	if (!hold) {
+		reg_val &= ~mask_val;
+		xhdmiphy_write(inst, XHDMIPHY_POWERDOWN_CONTROL_REG, reg_val);
+	}
+}
+
+/**
+ * xhdmiphy_mmcm_reset - This function will reset the mixed-mode clock manager
+ * (MMCM) core.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @hold:	Hold is an indicator whether to "hold" the reset if set to 1
+ *		If set to 0: reset, then enable
+ */
+void xhdmiphy_mmcm_reset(struct xhdmiphy_dev *inst, enum dir dir, u8 hold)
+{
+	u32 reg_off, reg_val;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_MMCM_TXUSRCLK_CTRL_REG;
+	else
+		reg_off = XHDMIPHY_MMCM_RXUSRCLK_CTRL_REG;
+
+	/* assert reset */
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val |= XHDMIPHY_MMCM_USRCLK_CTRL_RST_MASK;
+	xhdmiphy_write(inst, reg_off, reg_val);
+
+	if (!hold) {
+		/* de-assert reset */
+		reg_val &= ~XHDMIPHY_MMCM_USRCLK_CTRL_RST_MASK;
+		xhdmiphy_write(inst, reg_off, reg_val);
+	}
+}
+
+u64 xhdmiphy_get_pll_vco_freq(struct xhdmiphy_dev *inst, enum chid chid,
+			      enum dir dir)
+{
+	struct channel *pll_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+	struct pll_param pll_prm;
+	u64 pll_vco_rate, pll_refclk;
+	u32 qrefclk;
+
+	pll_prm = inst->quad.plls[XHDMIPHY_CH2IDX(chid)].pll_param;
+	qrefclk = xhdmiphy_get_quad_refclk(inst, pll_ptr->pll_refclk);
+
+	if (dir == XHDMIPHY_DIR_TX) {
+		if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX))
+			pll_refclk = inst->tx_refclk_hz;
+		else
+			pll_refclk = qrefclk;
+	} else {
+		if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX)) {
+			if (inst->rx_dru_enabled)
+				pll_refclk = xhdmiphy_get_dru_refclk(inst);
+			else
+				pll_refclk = inst->rx_refclk_hz;
+		} else {
+			pll_refclk = qrefclk;
+		}
+	}
+
+	pll_vco_rate = (u64)(pll_refclk * pll_prm.n1fb_div * pll_prm.n2fb_div) /
+			     pll_prm.m_refclk_div;
+
+	return pll_vco_rate;
+}
+
+/**
+ * xhdmiphy_pll_cal - This function will try to find the necessary PLL divisor
+ * values to produce the configured line rate given the specified PLL input
+ * frequency.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to calculate the PLL values for
+ * @dir:	dir is an indicator for TX or RX
+ * @pll_clkin_freq:
+ *		pll_clkin_freq is the PLL input frequency on which to base the
+ *		calculations on. A value of 0 indicates to use the currently
+ *		configured quad PLL reference clock. A non-zero value indicates
+ *		to ignore what is currently configured in SW, and use a custom
+ *		frequency instead.
+ *
+ * @return:	- 0 if valid PLL values were found to satisfy the constraints
+ *		- 1 otherwise
+ */
+u32 xhdmiphy_pll_cal(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir,
+		     u32 pll_clkin_freq)
+{
+	const struct gtpll_divs *gtpll_divs;
+	struct channel *pll_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+	u64 pllclk_out_freq, linerate_freq;
+	u64 pll_clkin_freqin = pll_clkin_freq;
+	u32 status;
+	const u8 *m, *n1, *n2, *d;
+	u8 id, id0, id1;
+
+	if (!pll_clkin_freqin)
+		pll_clkin_freqin =
+			xhdmiphy_get_quad_refclk(inst, pll_ptr->pll_refclk);
+
+	/* select PLL value table offsets */
+	if (xhdmiphy_is_ch(chid))
+		gtpll_divs = &inst->gt_adp->cpll_divs;
+	else
+		gtpll_divs = &inst->gt_adp->qpll_divs;
+
+	for (n2 = gtpll_divs->n2; *n2 != 0; n2++) {
+		for (n1 = gtpll_divs->n1; *n1 != 0; n1++) {
+			for (m = gtpll_divs->m; *m != 0; m++) {
+				pllclk_out_freq = (pll_clkin_freqin * *n1 * *n2) / *m;
+				/* Test if the calculated PLL clock is in the VCO range */
+				status = xhdmiphy_check_pll_oprange(inst, chid,
+								    pllclk_out_freq);
+				if (status != 0)
+					continue;
+
+				if ((xhdmiphy_is_ch(chid)))
+					pllclk_out_freq *= 2;
+
+				/* Apply TX/RX divisor */
+				for (d = gtpll_divs->d; *d != 0; d++) {
+					linerate_freq = pllclk_out_freq / *d;
+					if (linerate_freq == pll_ptr->linerate)
+						goto calc_done;
+				}
+			}
+		}
+	}
+	/* Calculation failed, don't change divisor settings */
+	return 1;
+
+calc_done:
+	/* Found the multiplier and divisor values for requested line rate */
+	pll_ptr->pll_param.m_refclk_div = *m;
+	pll_ptr->pll_param.nfb_div = *n1;
+	pll_ptr->pll_param.n2fb_div = *n2;
+	pll_ptr->pll_param.is_lowerband = 1;
+
+	if (xhdmiphy_is_cmn(chid)) {
+		/* Same divisor value for all channels if using a QPLL */
+		chid = XHDMIPHY_CHID_CHA;
+	}
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].outdiv[dir] = *d;
+		if (dir == XHDMIPHY_DIR_RX)
+			xhdmiphy_cfg_set_cdr(inst, (enum chid)id);
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xhdmiphy_gt_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xhdmiphy_gt_helper.c
@@ -0,0 +1,1398 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/device.h>
+#include "xhdmiphy.h"
+
+static const u8 gthe4_cpll_divs_m[] = {1, 2, 0};
+static const u8 gthe4_cpll_divs_n1[] = {4, 5, 0};
+static const u8 gthe4_cpll_divs_n2[] = {1, 2, 3, 4, 5, 8, 0};
+static const u8 gthe4_cpll_divs_d[] = {1, 2, 4, 8, 0};
+
+static const u8 gthe4_qpll_divs_m[] = {1, 2, 3, 4, 0};
+static const u8 gthe4_qpll_divs_n1[] = {16, 20, 25, 30, 32, 40, 60, 64, 66, 75,
+					80, 84, 90, 96, 100, 112, 120, 125, 150,
+					160, 0};
+static const u8 gthe4_qpll_divs_n2[] = {1, 0};
+static const u8 gthe4_qpll_divs_d[] = {1, 2, 4, 8, 16, 0};
+
+/**
+ * xhdmiphy_gt_mst_rst - This function will set the (TX|RX) MSTRESET port of
+ * the GT
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for TX or RX
+ * @rst:	rst set=true; Clear=false
+ */
+static void xhdmiphy_gt_mst_rst(struct xhdmiphy_dev *inst, enum chid chid,
+				enum dir dir, u8 rst)
+{
+	u32 reg_off, reg_val, mask_val = 0;
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+
+	for (id = id0; id <= id1; id++)
+		mask_val |=  XHDMIPHY_TXRX_MSTRESET_MASK(id);
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_TX_INIT_REG;
+	else
+		reg_off = XHDMIPHY_RX_INIT_REG;
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+
+	xhdmiphy_set_clr(inst, reg_off, reg_val, mask_val, rst);
+}
+
+ /**
+  * This function will translate the configured QPLL's M or CPLL's M or N2
+  * values to DRP encoding.
+  *
+  * @attr_enc:	attribute to encode
+  *
+  * @return:	encoded value
+  *
+  * @note: For more details about DRP encoding values , refer GT user guide
+  */
+static u8 xhdmiphy_drpenc_qpll_mcpll_mn2(u8 attr_enc)
+{
+	u8 drp_enc;
+
+	switch (attr_enc) {
+	case 1:
+		drp_enc = 16;
+		break;
+	case 6:
+		drp_enc = 5;
+		break;
+	case 10:
+		drp_enc = 7;
+		break;
+	case 12:
+		drp_enc = 13;
+		break;
+	case 20:
+		drp_enc = 15;
+		break;
+	case 2: case 3: case 4:
+	case 5: case 8: case 16:
+		drp_enc = (attr_enc - 2);
+		break;
+	default:
+		drp_enc = 0xf;
+	break;
+	}
+
+	return drp_enc;
+}
+
+/* This function translates the configured CPLL's N1 value to DRP encoding */
+static u8 xhdmiphy_drpenc_cpll_n1(u8 attr_enc)
+{
+	return (attr_enc - 4) & 0x1;
+}
+
+/* This function translates the configured QPLL's N value to DRP encoding */
+static u16 xhdmiphy_drpenc_qpll_n(u8 attr_enc)
+{
+	u16 drp_enc;
+
+	if (attr_enc >= 16 && attr_enc <= 160)
+		drp_enc = attr_enc - 2;
+	else
+		drp_enc = 0xff;
+
+	return drp_enc;
+}
+
+/* This function translates the configured CPLL's D values to DRP encoding */
+
+static u8 xhdmiphy_drpenc_cpll_txrx_d(u8 attr_enc)
+{
+	u8 drp_enc;
+
+	switch (attr_enc) {
+	case 1:
+		drp_enc = 0;
+		break;
+	case 2:
+		drp_enc = 1;
+		break;
+	case 4:
+		drp_enc = 2;
+		break;
+	case 8:
+		drp_enc = 3;
+		break;
+	case 16:
+		drp_enc = 4;
+		break;
+	default:
+		drp_enc = 0x4;
+		break;
+	}
+
+	return drp_enc;
+}
+
+/* This function translates the configured Rx data width to DRP encoding */
+static u8 xhdmiphy_drpenc_datawidth(u8 attr_enc)
+{
+	u8 drp_enc;
+
+	switch (attr_enc) {
+	case 16:
+		drp_enc = 2;
+		break;
+	case 20:
+		drp_enc = 3;
+		break;
+	case 32:
+		drp_enc = 4;
+		break;
+	case 40:
+		drp_enc = 5;
+		break;
+	case 64:
+		drp_enc = 6;
+		break;
+	case 80:
+		drp_enc = 7;
+		break;
+	case 128:
+		drp_enc = 8;
+		break;
+	case 160:
+		drp_enc = 9;
+		break;
+	default:
+		drp_enc = 0xf;
+		break;
+	}
+
+	return drp_enc;
+}
+
+/* This function translates the configured RXINTDATAWIDTH to DRP encoding */
+static u8 xhdmiphy_drpenc_int_datawidth(u8 attr_enc)
+{
+	u8 drp_enc;
+
+	switch (attr_enc) {
+	case 2:
+		drp_enc = 0;
+		break;
+	case 4:
+		drp_enc = 1;
+		break;
+	default:
+		drp_enc = 2;
+		break;
+	}
+
+	return drp_enc;
+}
+
+/* This function will translate the configured CLK25 to DRP encoding */
+static u16 xhdmiphy_drpenc_clk25(u32 refclk_hz)
+{
+	u16 drp_enc;
+	u32 refclk_mhz = refclk_hz / 1000000;
+
+	drp_enc = ((refclk_mhz / 25) +
+		   (((refclk_mhz % 25) > 0) ? 1 : 0)) - 1;
+
+	return (drp_enc & 0x1f);
+}
+
+/**
+ * xhdmiphy_cpll_cal_counttol - This function configures the cpll Calibration
+ * period and the count tolerance registers.
+ * cpll_cal_period = ((fPLLClkin * N1 * N2) / (20 * M)) /
+ *                       (16000 / (4 * fFreeRunClk))
+ * cpll_cal_tol = cpll_cal_period * 0.10
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance
+ * @chid:		chid is the channel ID to operate on
+ * @dir:		dir is an indicator for TX or RX
+ * @freerun_clk:	freerun_clk is the freerunning clock freq in Hz
+ *			driving the GT Wiz instance
+ *
+ * @return:		returns 0 on successful configuration or else returns 1
+ */
+static bool xhdmiphy_cpll_cal_counttol(struct xhdmiphy_dev *inst, enum chid chid,
+				       enum dir dir, u32 freerun_clk)
+{
+	u64 cpll_cal_period;
+	u64 cpll_cal_tol;
+	u64 pll_vco_freq;
+	u32 reg_val;
+
+	if (!xhdmiphy_is_ch(chid))
+		return false;
+
+	pll_vco_freq = xhdmiphy_get_pll_vco_freq(inst, chid, dir);
+	cpll_cal_period = pll_vco_freq * 200 / (u64)freerun_clk;
+	if (cpll_cal_period % 10)
+		cpll_cal_tol = (cpll_cal_period / 10) + 1;
+	else
+		cpll_cal_tol = cpll_cal_period / 10;
+
+	/* read cpll calibration period value */
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_CPLL_CAL_PERIOD_REG) &
+				~XHDMIPHY_CPLL_CAL_PERIOD_MASK;
+	reg_val |= cpll_cal_period & XHDMIPHY_CPLL_CAL_PERIOD_MASK;
+
+	/* write new cpll calibration period value */
+	xhdmiphy_write(inst, XHDMIPHY_CPLL_CAL_PERIOD_REG, reg_val);
+	/* read cpll calibration tolerance value */
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_CPLL_CAL_TOL_REG) &
+				~XHDMIPHY_CPLL_CAL_TOL_MASK;
+
+	reg_val |= cpll_cal_tol & XHDMIPHY_CPLL_CAL_TOL_MASK;
+	xhdmiphy_write(inst, XHDMIPHY_CPLL_CAL_TOL_REG, reg_val);
+
+	return false;
+}
+
+/**
+ * xhdmiphy_m_drpenc - This function will translate the configured M value to
+ * DRP encoding.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	The DRP encoding for M
+ */
+static u8 xhdmiphy_m_drpenc(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	struct pll_param pll_prm;
+	u8 m_refclk_div;
+
+	pll_prm = inst->quad.plls[XHDMIPHY_CH2IDX(chid)].pll_param;
+
+	if (chid >= XHDMIPHY_CHID_CH1 && chid <= XHDMIPHY_CHID_CH4)
+		m_refclk_div = pll_prm.m_refclk_div;
+	else if (chid == XHDMIPHY_CHID_CMN0 || chid == XHDMIPHY_CHID_CMN1)
+		m_refclk_div = pll_prm.m_refclk_div;
+	else
+		m_refclk_div = 0;
+
+	return xhdmiphy_drpenc_qpll_mcpll_mn2(m_refclk_div);
+}
+
+/**
+ * xhdmiphy_gthe4_set_cdr - This function will set the clock and data recovery
+ * (CDR) values for a given channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static bool xhdmiphy_gthe4_set_cdr(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	struct channel *ch_ptr;
+	u8 rx_outdiv;
+
+	if (chid < XHDMIPHY_CHID_CH1 || chid > XHDMIPHY_CHID_CH4)
+		return true;
+
+	ch_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+	rx_outdiv = ch_ptr->rx_outdiv;
+
+	ch_ptr->pll_param.cdr[0] = XHDMIPHY_RXCDR_CFG_WORD0;
+	ch_ptr->pll_param.cdr[1] = XHDMIPHY_RXCDR_CFG_WORD1;
+	ch_ptr->pll_param.cdr[3] = XHDMIPHY_RXCDR_CFG_WORD3;
+	ch_ptr->pll_param.cdr[4] = XHDMIPHY_RXCDR_CFG_WORD4;
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX)) {
+		/*
+		 * rx_outdiv = 1 => cdr[2] = 0x0262
+		 * rx_outdiv = 2 => cdr[2] = 0x0252
+		 * rx_outdiv = 4 => cdr[2] = 0x0242
+		 * rx_outdiv = 8 => cdr[2] = 0x0232
+		 * rx_outdiv = 16 => cdr[2] = 0x0222
+		 */
+		ch_ptr->pll_param.cdr[2] = XHDMIPHY_RXCDR_CFG_WORD2;
+
+		while (rx_outdiv >>= 1)
+			ch_ptr->pll_param.cdr[2] -=
+						XHDMIPHY_RXCDR_CFG_WORD2_RXDIV;
+
+	} else {
+		return true;
+	}
+
+	return false;
+}
+
+/**
+ * xhdmiphy_gthe4_check_pll_oprange - This function will check if a given PLL
+ * output frequency is within the operating range of the PLL for the GT type.
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance
+ * @chid:		chid is the channel ID to operate on
+ * @pll_clkout_freq:	pll_clkout_freq is the frequency to check
+ *
+ * @return:		- 0 if the frequency resides within the PLL's range
+ *			- 1 otherwise
+ */
+static bool xhdmiphy_gthe4_check_pll_oprange(struct xhdmiphy_dev *inst, enum chid chid,
+					     u64 pll_clkout_freq)
+{
+	if ((chid == XHDMIPHY_CHID_CMN0 &&
+	     pll_clkout_freq >= XHDMIPHY_QPLL0_MIN &&
+	     pll_clkout_freq <= XHDMIPHY_QPLL0_MAX) ||
+	    (chid == XHDMIPHY_CHID_CMN1 &&
+	     pll_clkout_freq >= XHDMIPHY_QPLL1_MIN &&
+	     pll_clkout_freq <= XHDMIPHY_QPLL1_MAX) ||
+	    (chid >= XHDMIPHY_CHID_CH1 &&
+	     chid <= XHDMIPHY_CHID_CH4 &&
+	     pll_clkout_freq >= XHDMIPHY_CPLL_MIN &&
+	     pll_clkout_freq <= XHDMIPHY_CPLL_MAX)) {
+		return false;
+	}
+
+	return true;
+}
+
+/**
+ * xhdmiphy_d_drpenc - This function will translate the configured D value to
+ * DRP encoding.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:	The DRP encoding for D
+ */
+static u8 xhdmiphy_d_drpenc(struct xhdmiphy_dev *inst, enum chid chid,
+			    enum dir dir)
+{
+	u8 out_div;
+
+	out_div = inst->quad.plls[XHDMIPHY_CH2IDX(chid)].outdiv[dir];
+
+	return xhdmiphy_drpenc_cpll_txrx_d(out_div);
+}
+
+/**
+ * xhdmiphy_gthe4_outdiv_chreconf - This function will set the output divider
+ * logic for a given channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static u32 xhdmiphy_gthe4_outdiv_chreconf(struct xhdmiphy_dev *inst,
+					  enum chid chid, enum dir dir)
+{
+	u32 status = 0;
+	u16 drp_val, write_val;
+
+	if (dir == XHDMIPHY_DIR_RX) {
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0063,
+					 &drp_val);
+		/* Mask out RXOUT_DIV */
+		drp_val &= ~XDRP_GTHE4_CHN_REG_0063_RXOUT_DIV_MASK;
+		/* Set RXOUT_DIV */
+		write_val = (xhdmiphy_d_drpenc(inst, chid, XHDMIPHY_DIR_RX) &
+			    XDRP_GTHE4_CHN_REG_0063_FLD_RXOUT_DIV_MASK);
+		drp_val |= write_val;
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0063,
+					 drp_val);
+	} else {
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_007C,
+					 &drp_val);
+		/* mask out TXOUT_DIV */
+		drp_val &= ~XDRP_GTHE4_CHN_REG_007C_TXOUT_DIV_MASK;
+		/* Set TXOUT_DIV */
+		write_val = (xhdmiphy_d_drpenc(inst, chid, XHDMIPHY_DIR_TX) &
+			     XDRP_GTHE4_CHN_REG_007C_FLD_TX_RXDETECT_REF_MASK);
+		drp_val |= (write_val << XHDMIPHY_DRP_TXOUT_OFFSET);
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_007C,
+					 drp_val);
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_n_drpenc - This function will translate the configured N1/N2 value
+ * to DRP encoding.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @nid:	NId specified to operate on N1 (if == 1) or N2 (if == 2)
+ *
+ * @return:	The DRP encoding for N1/N2
+ */
+static u16 xhdmiphy_n_drpenc(struct xhdmiphy_dev *inst, enum chid chid, u8 nid)
+{
+	struct pll_param pll_prm;
+	u16 drp_enc;
+	u8 nfb_div;
+
+	pll_prm = inst->quad.plls[XHDMIPHY_CH2IDX(chid)].pll_param;
+
+	if (chid == XHDMIPHY_CHID_CMN0 || chid == XHDMIPHY_CHID_CMN1) {
+		nfb_div = pll_prm.nfb_div;
+		drp_enc = xhdmiphy_drpenc_qpll_n(nfb_div);
+	} else if (nid == 1) {
+		nfb_div = pll_prm.n1fb_div;
+		drp_enc = xhdmiphy_drpenc_cpll_n1(nfb_div);
+	} else {
+		nfb_div = pll_prm.n2fb_div;
+		drp_enc = xhdmiphy_drpenc_qpll_mcpll_mn2(nfb_div);
+	}
+
+	return drp_enc;
+}
+
+/**
+ * xhdmiphy_gthe4_clkch_reconf - This function will configure the channel clock
+ * settings.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static u32 xhdmiphy_gthe4_clkch_reconf(struct xhdmiphy_dev *inst,
+				       enum chid chid)
+{
+	u32 cpll_vco_mhz, status = 0;
+	u16 drp_val, write_val;
+
+	/* Obtain current DRP register value for PLL dividers */
+	status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0028, &drp_val);
+	/* Mask out clock divider bits */
+	drp_val &= ~(XDRP_GTHE4_CHN_REG_0028_CPLL_FBDIV_MASK);
+	/* Set CPLL_FBDIV */
+	write_val = (xhdmiphy_n_drpenc(inst, chid, 2) &
+		     XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_MASK);
+	drp_val |= (write_val << XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_SHIFT);
+	/* Set CPLL_FBDIV_45 */
+	write_val = (xhdmiphy_n_drpenc(inst, chid, 1) &
+		     XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_45_MASK);
+	drp_val |= (write_val << XDRP_GTHE4_CHN_REG_0028_FLD_CPLL_FBDIV_45_SHIFT);
+	/* write new DRP register value for PLL dividers */
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0028, drp_val);
+	/* write CPLL Ref Clk Div */
+	status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_002A, &drp_val);
+	/* Mask out clock divider bits */
+	drp_val &= ~(XDRP_GTHE4_CHN_REG_002A_CPLL_REFCLK_DIV_MASK);
+	/* Set CPLL_REFCLKDIV */
+	write_val = (xhdmiphy_m_drpenc(inst, chid) &
+		     XDRP_GTHE4_CHN_REG_002A_FLD_A_TXDIFFCTRL_MASK);
+	drp_val |= (write_val << XDRP_GTHE4_CHN_REG_002A_FLD_A_TXDIFFCTRL_SHIFT);
+	/* write new DRP register value for PLL dividers */
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_002A, drp_val);
+
+	cpll_vco_mhz =
+	xhdmiphy_get_pll_vco_freq(inst, chid,
+				  xhdmiphy_is_tx_using_cpll(inst, chid) ?
+				  XHDMIPHY_DIR_TX : XHDMIPHY_DIR_RX) / 1000000;
+	/* CPLL_CFG0 */
+	if (cpll_vco_mhz <= XHDMIPHY_DRP_CPLL_VCO_RANGE1)
+		drp_val = XHDMIPHY_DRP_CPLL_CFG0_VAL1;
+	else if (cpll_vco_mhz <= XHDMIPHY_DRP_CPLL_VCO_RANGE2)
+		drp_val = XHDMIPHY_DRP_CPLL_CFG0_VAL2;
+	else
+		drp_val = XHDMIPHY_DRP_CPLL_CFG0_VAL3;
+
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00CB, drp_val);
+	/* CPLL_CFG1 */
+	if (cpll_vco_mhz <= XHDMIPHY_DRP_CPLL_VCO_RANGE1)
+		drp_val = XHDMIPHY_DRP_CPLL_CFG1_VAL1;
+	else
+		drp_val = XHDMIPHY_DRP_CPLL_CFG1_VAL2;
+
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00CC, drp_val);
+	/* CPLL_CFG2 */
+	if (cpll_vco_mhz <= XHDMIPHY_DRP_CPLL_VCO_RANGE1)
+		drp_val = XHDMIPHY_DRP_CPLL_CFG2_VAL1;
+	else if (cpll_vco_mhz <= XHDMIPHY_DRP_CPLL_VCO_RANGE2)
+		drp_val = XHDMIPHY_DRP_CPLL_CFG2_VAL2;
+	else
+		drp_val = XHDMIPHY_DRP_CPLL_CFG2_VAL3;
+
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00BC, drp_val);
+	/* configure CPLL Calibration Registers */
+	xhdmiphy_cpll_cal_counttol(inst, chid,
+				   (xhdmiphy_is_tx_using_cpll(inst, chid) ?
+				   XHDMIPHY_DIR_TX : XHDMIPHY_DIR_RX),
+				   inst->conf.drpclk_freq);
+
+	return status;
+}
+
+static u8 xhdmiphy_get_refclk_src_cnt(struct xhdmiphy_dev *inst)
+{
+	enum refclk_sel refclk_sel[XHDMIPHY_REFCLKSEL_MAX];
+	enum refclk_sel refclk_sel_tmp[XHDMIPHY_REFCLKSEL_MAX];
+	u8 i, j, match, refclk_num = 0;
+
+	refclk_sel[0] = (inst->conf.tx_protocol != XHDMIPHY_PROT_NONE) ?
+			 inst->conf.tx_refclk_sel : 99;
+	refclk_sel[1] = (inst->conf.rx_protocol != XHDMIPHY_PROT_NONE) ?
+			 inst->conf.rx_refclk_sel : 99;
+	refclk_sel[2] = (inst->conf.dru_present) ?
+			 inst->conf.dru_refclk_sel : 99;
+	refclk_sel[3] = (inst->conf.tx_protocol == XHDMIPHY_PROT_HDMI21) ?
+			 inst->conf.tx_frl_refclk_sel : 99;
+	refclk_sel[4] = (inst->conf.rx_protocol == XHDMIPHY_PROT_HDMI21) ?
+			 inst->conf.rx_frl_refclk_sel : 99;
+
+	/* initialize Unique refclock holder */
+	for (i = 0; i < XHDMIPHY_REFCLKSEL_MAX; i++)
+		refclk_sel_tmp[i] = 99;
+
+	i = 0;
+	do {
+		if (refclk_sel[i] != 99) {
+			match = 0;
+			j = 0;
+			/* Check if refclk_sel is already in unique holder array */
+			do {
+				if (refclk_sel_tmp[j] == refclk_sel[i])
+					match |= 1;
+				j++;
+			} while (j < refclk_num);
+
+			/* register in unique holder if new RefClk is detected */
+			if (match == 0) {
+				refclk_sel_tmp[refclk_num] = refclk_sel[i];
+				/* increment refclk counter */
+				refclk_num++;
+			}
+		}
+		i++;
+	} while (i < XHDMIPHY_REFCLKSEL_MAX);
+
+	return refclk_num;
+}
+
+/**
+ * xhdmiphy_gthe4_clkcmn_reconf - This function will configure the common
+ * channel clock settings.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @cmn_id:	cmn_id is the common channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static u32 xhdmiphy_gthe4_clkcmn_reconf(struct xhdmiphy_dev *inst,
+					enum chid cmn_id)
+{
+	u32 qpll_vco_mhz, qpll_clkout_mhz, status = 0;
+	u16 drp_val, write_val;
+	u8 nfb_div;
+
+	nfb_div = inst->quad.plls[XHDMIPHY_CH2IDX(cmn_id)].pll_param.nfb_div;
+
+	/* Obtain current DRP register value for QPLL_FBDIV */
+	status |= xhdmiphy_drprd(inst, XHDMIPHY_CHID_CMN,
+		  (cmn_id == XHDMIPHY_CHID_CMN0) ? XDRP_GTHE4_CMN_REG_0014 :
+			     XDRP_GTHE4_CMN_REG_0094, &drp_val);
+	/* Mask out QPLL_FBDIV */
+	drp_val &= ~(XDRP_GTHE4_CMN_REG_0014_FLD_QPLL0_INIT_CFG1_MASK);
+	/* Set QPLL_FBDIV */
+	write_val = (xhdmiphy_n_drpenc(inst, cmn_id, 0) &
+		    XDRP_GTHE4_CMN_REG_0014_FLD_QPLL0_INIT_CFG1_MASK);
+	drp_val |= write_val;
+	/* write new DRP register value for QPLL_FBDIV */
+	status |= xhdmiphy_drpwr(inst, XHDMIPHY_CHID_CMN,
+				 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+				 XDRP_GTHE4_CMN_REG_0014 :
+				 XDRP_GTHE4_CMN_REG_0094, drp_val);
+
+	/* Obtain current DRP register value for QPLL_REFCLK_DIV */
+	status |= xhdmiphy_drprd(inst, XHDMIPHY_CHID_CMN,
+				 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+				 XDRP_GTHE4_CMN_REG_0018 :
+				 XDRP_GTHE4_CMN_REG_0098, &drp_val);
+	/* Mask out QPLL_REFCLK_DIV */
+	drp_val &= ~(XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_MASK);
+	if (xhdmiphy_get_refclk_src_cnt(inst) > 1)
+		drp_val |= (1 << XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_SHIFT);
+
+	write_val = (xhdmiphy_m_drpenc(inst, cmn_id) &
+		    XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_MASK1);
+	drp_val |= (write_val <<
+		    XDRP_GTHE4_CMN_REG_0018_QPLLX_REFCLK_DIV_SHIFT1);
+
+	status |= xhdmiphy_drpwr(inst, XHDMIPHY_CHID_CMN,
+				 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+				 XDRP_GTHE4_CMN_REG_0018 :
+				 XDRP_GTHE4_CMN_REG_0098, drp_val);
+	if ((xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX)) ||
+	    (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX))) {
+		qpll_vco_mhz =
+		xhdmiphy_get_pll_vco_freq(inst, cmn_id,
+					  xhdmiphy_is_using_qpll(inst, cmn_id, XHDMIPHY_DIR_TX) ?
+					  XHDMIPHY_DIR_TX : XHDMIPHY_DIR_RX) / 1000000;
+		qpll_clkout_mhz = qpll_vco_mhz / 2;
+
+		status |= xhdmiphy_drprd(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_000D :
+					 XDRP_GTHE4_CMN_REG_008D, &drp_val);
+
+		drp_val &= ~(XDRP_GTHE4_CMN_REG_000D_PPFX_CFG_MASK);
+		if (qpll_vco_mhz >= XHDMIPHY_DRP_QPLL_VCO_RANGE1)
+			drp_val |= XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL1;
+		else if (qpll_vco_mhz >= XHDMIPHY_DRP_QPLL_VCO_RANGE3)
+			drp_val |= XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL2;
+		else if (qpll_vco_mhz >= XHDMIPHY_DRP_QPLL_VCO_RANGE4)
+			drp_val |= XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL3;
+		else
+			drp_val |= XHDMIPHY_DRP_PPF_MUX_CRNT_CTRL0_VAL4;
+
+		if (qpll_vco_mhz >= XHDMIPHY_DRP_QPLL_VCO_RANGE2)
+			drp_val |= XHDMIPHY_DRP_PPF_MUX_TERM_CTRL0_VAL1;
+		else
+			drp_val |= XHDMIPHY_DRP_PPF_MUX_TERM_CTRL0_VAL2;
+
+		/* write new DRP register value for PPFx_CFG */
+		status |= xhdmiphy_drpwr(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_000D :
+					 XDRP_GTHE4_CMN_REG_008D, drp_val);
+		/* QPLL_CP */
+		if (nfb_div <= XHDMIPHY_DRP_QPLL_NFBDIV)
+			drp_val = XHDMIPHY_DRP_QPLL_CP_VAL1;
+		else
+			drp_val = XHDMIPHY_DRP_QPLL_CP_VAL2;
+
+		/* write new DRP register value for QPLL_CP */
+		status |= xhdmiphy_drpwr(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_0016 :
+					 XDRP_GTHE4_CMN_REG_0096, drp_val);
+		/* QPLL_LPF */
+		status |= xhdmiphy_drprd(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_0019 :
+					 XDRP_GTHE4_CMN_REG_0099, &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CMN_REG_0019_QPLLX_LPF_MASK);
+		if (nfb_div <= XHDMIPHY_DRP_QPLL_NFBDIV)
+			drp_val |= XHDMIPHY_DRP_QPLL_LPF_VAL1;
+		else
+			drp_val |= XHDMIPHY_DRP_QPLL_LPF_VAL2;
+
+		status |= xhdmiphy_drpwr(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_0019 :
+					 XDRP_GTHE4_CMN_REG_0099, drp_val);
+		status |= xhdmiphy_drprd(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_0030 :
+					 XDRP_GTHE4_CMN_REG_00B0, &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CMN_REG_0030_QPLLX_CFG4_MASK);
+
+		if (qpll_clkout_mhz >= XHDMIPHY_DRP_QPLL_CLKOUT_RANGE1)
+			drp_val |= XHDMIPHY_DRP_Q_TERM_CLK_VAL1 <<
+				   XHDMIPHY_DRP_Q_DCRNT_CLK_SHIFT;
+		else if (qpll_clkout_mhz >= XHDMIPHY_DRP_QPLL_CLKOUT_RANGE2)
+			drp_val |= XHDMIPHY_DRP_Q_TERM_CLK_VAL2 <<
+				   XHDMIPHY_DRP_Q_DCRNT_CLK_SHIFT;
+		else
+			drp_val |= XHDMIPHY_DRP_Q_TERM_CLK_VAL3 <<
+				   XHDMIPHY_DRP_Q_DCRNT_CLK_SHIFT;
+
+		if (qpll_clkout_mhz >= XHDMIPHY_DRP_QPLL_CLKOUT_RANGE1)
+			drp_val |= XHDMIPHY_DRP_Q_DCRNT_CLK_VAL1;
+		else if (qpll_clkout_mhz >= XHDMIPHY_DRP_QPLL_CLKOUT_RANGE3)
+			drp_val |= XHDMIPHY_DRP_Q_DCRNT_CLK_VAL2;
+		else
+			drp_val |= XHDMIPHY_DRP_Q_DCRNT_CLK_VAL3;
+
+		/* write new DRP register value for QPLL_CFG4 */
+		status |= xhdmiphy_drpwr(inst, XHDMIPHY_CHID_CMN,
+					 (cmn_id == XHDMIPHY_CHID_CMN0) ?
+					 XDRP_GTHE4_CMN_REG_0030 :
+					 XDRP_GTHE4_CMN_REG_00B0, drp_val);
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_gthe4_rxpll_div1_reconf - This function will configure the
+ * channel's RX CLKDIV1 settings.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static bool xhdmiphy_gthe4_rxpll_div1_reconf(struct xhdmiphy_dev *inst,
+					     enum chid chid)
+{
+	struct channel *pll_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+	u32 rx_refclk, status = 0;
+	u16 drp_val;
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX))
+		rx_refclk = inst->rx_refclk_hz;
+	else
+		rx_refclk = xhdmiphy_get_quad_refclk(inst, pll_ptr->pll_refclk);
+
+	status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_006D, &drp_val);
+	drp_val &= ~XDRP_GTHE4_CHN_REG_006D_RXCLK25_MASK;
+	drp_val |= xhdmiphy_drpenc_clk25(rx_refclk) << 3;
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_006D, drp_val);
+
+	return status;
+}
+
+/**
+ * xhdmiphy_gthe4_rxch_reconf - This function will configure the channel's RX
+ * settings.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static u32 xhdmiphy_gthe4_rxch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	struct channel *ch_ptr;
+	enum chid chid_pll;
+	enum pll_type pll_type;
+	u64 linkrate;
+	u32 xvcorate_mhz, pll_clkout_mhz, pll_clkout_div, status = 0;
+	u16 drp_val, write_val;
+	u8 i;
+
+	ch_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+
+	for (i = 0; i < 5; i++) {
+		drp_val = ch_ptr->pll_param.cdr[i];
+		if (!drp_val) {
+			/* don't modify RX_CDR configuration */
+			continue;
+		}
+		status |= xhdmiphy_drpwr(inst, chid, XHDMIPHY_DRP_RXCDR_CFG(i),
+					 drp_val);
+		if (i == 2) {
+			status |= xhdmiphy_drpwr(inst, chid,
+				  XHDMIPHY_DRP_RXCDR_CFG_GEN3(i), drp_val);
+		}
+	}
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX)) {
+		pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX, chid);
+		switch (pll_type) {
+		case XHDMIPHY_PLL_QPLL:
+		case XHDMIPHY_PLL_QPLL0:
+			chid_pll = XHDMIPHY_CHID_CMN0;
+			pll_clkout_div = XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL1;
+			break;
+		case XHDMIPHY_PLL_QPLL1:
+			chid_pll = XHDMIPHY_CHID_CMN1;
+			pll_clkout_div = XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL1;
+			break;
+		default:
+			chid_pll = chid;
+			pll_clkout_div = XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL2;
+			break;
+		}
+
+		linkrate = xhdmiphy_get_linerate(inst, chid_pll) / 1000;
+		/* RXCDR_CFG3 & RXCDR_CFG3_GEN3 */
+		if (linkrate > XHDMIPHY_DRP_LINERATEKHZ_1)
+			drp_val = XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL1;
+		else if ((linkrate > XHDMIPHY_DRP_LINERATEKHZ_2) &&
+			 (ch_ptr->rx_data_width == XHDMIPHY_DRP_RX_DATAWIDTH_64))
+			drp_val = XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL2;
+		else if (linkrate > XHDMIPHY_DRP_LINERATEKHZ_3)
+			drp_val = XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL1;
+		else
+			drp_val = XHDMIPHY_DRP_RXCDR_CFG_WORD3_VAL3;
+
+		/* write RXCDR_CFG3 Value */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0011,
+					 drp_val);
+		/* write RXCDR_CFG3_GEN3 Value */
+		status |= xhdmiphy_drpwr(inst, chid,
+					 XHDMIPHY_DRP_RXCDR_CFG_GEN3(3),
+					 drp_val);
+		/* RXCDR_CFG2_GEN2 & RXCDR_CFG3_GEN2 */
+		/* Get [15:10] from RXCDR_CFG3[5:0] */
+		drp_val = (drp_val &
+			  XDRP_GTHE4_CHN_REG_0011_RXCDR_CGF3_GEN2_MASK) <<
+			  XDRP_GTHE4_CHN_REG_0011_RXCDR_CGF3_GEN2_SHIFT;
+		/* Get [9:0] from RXCDR_CFG2[9:0] */
+		drp_val &= ~XDRP_GTHE4_CHN_REG_00AF_RXCDR_CGF2_GEN2_MASK;
+		drp_val |= ch_ptr->pll_param.cdr[2] &
+			   XDRP_GTHE4_CHN_REG_00AF_RXCDR_CGF2_GEN2_MASK;
+		/* write RXCDR_CFG2_GEN2 & RXCDR_CFG3_GEN2 value */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00AF,
+					 drp_val);
+
+		/* RX_WIDEMODE_CDR Encoding */
+		switch (ch_ptr->rx_data_width) {
+		case XHDMIPHY_DRP_RX_DATAWIDTH_80:
+			if (linkrate > XHDMIPHY_DRP_LINERATEKHZ_4)
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL1 <<
+					    XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT;
+			else
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL2 <<
+					    XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT;
+			break;
+		case XHDMIPHY_DRP_RX_DATAWIDTH_64:
+			if (linkrate > XHDMIPHY_DRP_LINERATEKHZ_5)
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL1 <<
+					    XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT;
+			else
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL2 <<
+					    XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT;
+			break;
+		case XHDMIPHY_DRP_RX_DATAWIDTH_40:
+			if (linkrate > XHDMIPHY_DRP_LINERATEKHZ_3)
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL2 <<
+					    XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT;
+			else
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL3;
+			break;
+		case XHDMIPHY_DRP_RX_DATAWIDTH_32:
+			if (linkrate > XHDMIPHY_DRP_LINERATEKHZ_6)
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL2 <<
+					    XHDMIPHY_RX_WIDEMODE_CDR_ENC_SHIFT;
+			else
+				write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL3;
+			break;
+		default:
+			write_val = XHDMIPHY_RX_WIDEMODE_CDR_ENC_VAL3;
+			break;
+		}
+
+		/* RX_INT_DATAWIDTH & RX_WIDEMODE_CDR */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0066,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_0066_RX_INT_DATAWIDTH_MASK);
+		/* Update RX_WIDEMODE_CDR Value */
+		drp_val |= write_val & XDRP_GTHE4_CHN_REG_0066_RX_WIDEMODE_CDR_MASK;
+		write_val = (xhdmiphy_drpenc_int_datawidth(ch_ptr->rx_intdata_width) &
+			    XDRP_GTHE4_CHN_REG_0066_RX_WIDEMODE_CDR_MASK_VAL);
+
+		drp_val |= write_val;
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0066,
+					 drp_val);
+		/* RX_DATA_WIDTH */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0003,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_0003_RX_DATAWIDTH_MASK);
+		write_val = (xhdmiphy_drpenc_datawidth(ch_ptr->rx_data_width) &
+			    XDRP_GTHE4_CHN_REG_0003_RX_DATAWIDTH_ENC_MASK);
+		write_val <<= XDRP_GTHE4_CHN_REG_0003_RX_DATAWIDTH_ENC_SHIFT;
+		drp_val |= write_val;
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0003,
+					 drp_val);
+		xvcorate_mhz = xhdmiphy_get_pll_vco_freq(inst, chid_pll,
+							 XHDMIPHY_DIR_RX) / 1000000;
+		pll_clkout_mhz = xvcorate_mhz / pll_clkout_div;
+		/* CH_HSPMUX_RX */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0116,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_0116_CH_RX_HSPMUX_MASK);
+
+		if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE1)
+			drp_val |= XHDMIPHY_DRP_PLLX_CLKOUT_VAL1;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE3)
+			drp_val |= XHDMIPHY_DRP_PLLX_CLKOUT_VAL2;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE2)
+			drp_val |= XHDMIPHY_DRP_PLLX_CLKOUT_VAL3;
+		else
+			drp_val |= XHDMIPHY_DRP_PLLX_CLKOUT_VAL4;
+
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0116,
+					 drp_val);
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_00FB,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_00FB_PREIQ_FREQ_BST_MASK);
+
+		if (pll_clkout_mhz > XHDMIPHY_DRP_PLL_CLKOUT_RANGE4)
+			drp_val |= XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL1 <<
+				   XHDMIPHY_DRP_PREIQ_FREQ_BST_SHIFT;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE5)
+			drp_val |= XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL2 <<
+				   XHDMIPHY_DRP_PREIQ_FREQ_BST_SHIFT; /* LPM mode */
+		else if (pll_clkout_mhz >= 10000)
+			drp_val |= XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL2 <<
+				   XHDMIPHY_DRP_PREIQ_FREQ_BST_SHIFT;
+		else if (pll_clkout_mhz >= 6000)
+			drp_val |= XHDMIPHY_DRP_PREIQ_FREQ_BST_VAL3 <<
+				   XHDMIPHY_DRP_PREIQ_FREQ_BST_SHIFT;
+
+		/* write new DRP register value for PREIQ_FREQ_BST */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00FB,
+					 drp_val);
+
+		/* RXPI_CFG0 */
+		if (pll_clkout_mhz > XHDMIPHY_DRP_PLL_CLKOUT_RANGE8)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL1;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE9)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL2;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE10)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL3;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE11)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL4;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE12)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL5;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE13)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL6;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE14)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL7;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE15)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL8;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE16)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL9;
+		else
+			drp_val = XHDMIPHY_DRP_RXPI_CFG0_VAL10;
+
+		/* write new DRP register value for RXPI_CFG0 */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_009D,
+					 drp_val);
+		/* RXPI_CFG1 */
+		if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE10)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG1_VAL1;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE12)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG1_VAL2;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE14)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG1_VAL3;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE18)
+			drp_val = XHDMIPHY_DRP_RXPI_CFG1_VAL4;
+		else
+			drp_val = XHDMIPHY_DRP_RXPI_CFG1_VAL5;
+
+		/* write new DRP register value for RXPI_CFG1 */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0100,
+					 drp_val);
+	}
+
+	status |= xhdmiphy_gthe4_rxpll_div1_reconf(inst, chid);
+
+	return status;
+}
+
+/**
+ * xhdmiphy_gthe4_txpll_div1_reconf - This function will configure the
+ * channel's TX CLKDIV1 settings.
+ *
+ * @inst:	inst is a pointer to the XHdmiphy1 core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static u32 xhdmiphy_gthe4_txpll_div1_reconf(struct xhdmiphy_dev *inst,
+					    enum chid chid)
+{
+	struct channel *pll_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+	u32 tx_refclkhz;
+	u32 status = 0;
+	u16 drp_val;
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX))
+		tx_refclkhz = inst->tx_refclk_hz;
+	else
+		tx_refclkhz = xhdmiphy_get_quad_refclk(inst,
+						       pll_ptr->pll_refclk);
+
+	status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_007A, &drp_val);
+	drp_val &= ~XDRP_GTHE4_CHN_REG_007A_TXCLK25_MASK;
+	drp_val |= xhdmiphy_drpenc_clk25(tx_refclkhz) <<
+		   XDRP_GTHE4_CHN_REG_007A_TXCLK25_SHIFT;
+	status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_007A, drp_val);
+
+	return status;
+}
+
+/**
+ * xhdmiphy_gthe4_txch_reconf - This function will configure the channel's
+ * TX settings.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static u32 xhdmiphy_gthe4_txch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	struct channel *ch_ptr;
+	enum chid chid_pll;
+	enum pll_type pll_type;
+	u32 ret_val, xvcorate_mhz, pll_clkout_mhz, pll_clkout_div;
+	u32 status = 0;
+	u16 drp_val, write_val;
+
+	ret_val = xhdmiphy_gthe4_txpll_div1_reconf(inst, chid);
+	if (!xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX))
+		return ret_val;
+
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX, chid);
+
+	switch (pll_type) {
+	case XHDMIPHY_PLL_QPLL:
+	case XHDMIPHY_PLL_QPLL0:
+		chid_pll = XHDMIPHY_CHID_CMN0;
+		pll_clkout_div = XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL1;
+		break;
+	case XHDMIPHY_PLL_QPLL1:
+		chid_pll = XHDMIPHY_CHID_CMN1;
+		pll_clkout_div = XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL1;
+		break;
+	default:
+		chid_pll = chid;
+		pll_clkout_div = XHDMIPHY_DRP_PLL_CLKOUT_DIV_VAL2;
+		break;
+	}
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX)) {
+		ch_ptr = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)];
+		/* set TX_PROGDIV_CFG to 20/40 */
+		if (pll_type == XHDMIPHY_PLL_QPLL ||
+		    pll_type == XHDMIPHY_PLL_QPLL0 ||
+		    pll_type == XHDMIPHY_PLL_QPLL1) {
+			if (inst->quad.plls[XHDMIPHY_CH2IDX(chid)].tx_outdiv != 16) {
+				/* TX_PROGDIV_CFG = 20 */
+				xhdmiphy_drpwr(inst, chid,
+					       XDRP_GTHE4_CHN_REG_003E,
+					       XDRP_GTHE4_CHN_REG_003E_DRP_VAL1);
+			} else {
+				/* TX_PROGDIV_CFG = 40 */
+				xhdmiphy_drpwr(inst, chid,
+					       XDRP_GTHE4_CHN_REG_003E,
+					       XDRP_GTHE4_CHN_REG_003E_DRP_VAL2);
+			}
+		}
+
+		/* TX_INT_DATAWIDTH */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0085,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_0085_TX_INT_DATAWIDTH_MASK <<
+			    XDRP_GTHE4_CHN_REG_0085_TX_INT_DATAWIDTH_SHIFT);
+		write_val = (xhdmiphy_drpenc_int_datawidth(ch_ptr->tx_intdata_width) &
+			    XDRP_GTHE4_CHN_REG_0085_TX_INT_DATAWIDTH_MASK);
+		write_val = write_val << XDRP_GTHE4_CHN_REG_0085_TX_INT_DATAWIDTH_SHIFT;
+		drp_val |= write_val;
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0085,
+					 drp_val);
+		/* TX_DATA_WIDTH */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_007A,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_007A_TX_DATA_WIDTH_MASK);
+		write_val = (xhdmiphy_drpenc_datawidth(ch_ptr->tx_data_width) &
+			    XDRP_GTHE4_CHN_REG_007A_TX_DATA_WIDTH_MASK);
+
+		drp_val |= write_val;
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_007A,
+					 drp_val);
+
+		/* TXPH_CFG */
+		if (ch_ptr->tx_outdiv == XHDMIPHY_DRP_TX_OUTDIV_VAL1) {
+			if (ch_ptr->tx_data_width >
+			    XHDMIPHY_DRP_TX_DATAWIDTH_VAL1)
+				drp_val = XHDMIPHY_DRP_TXPH_CFG_VAL1;
+			else
+				drp_val = XHDMIPHY_DRP_TXPH_CFG_VAL2;
+		} else if (ch_ptr->tx_outdiv ==
+			   XHDMIPHY_DRP_TX_OUTDIV_VAL2) {
+			if (ch_ptr->tx_data_width >
+			    XHDMIPHY_DRP_TX_DATAWIDTH_VAL2)
+				drp_val = XHDMIPHY_DRP_TXPH_CFG_VAL1;
+			else
+				drp_val = XHDMIPHY_DRP_TXPH_CFG_VAL2;
+		} else {
+			drp_val = XHDMIPHY_DRP_TXPH_CFG_VAL1;
+		}
+
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0073,
+					 drp_val);
+		xvcorate_mhz = xhdmiphy_get_pll_vco_freq(inst, chid_pll,
+							 XHDMIPHY_DIR_TX) / 1000000;
+		pll_clkout_mhz = xvcorate_mhz / pll_clkout_div;
+
+		/* TXPI_CFG */
+		if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE10)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG_VAL1;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE14)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG_VAL2;
+		else
+			drp_val = XHDMIPHY_DRP_TXPI_CFG_VAL3;
+
+		/* write new DRP register value for TXPI_CFG */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00FF,
+					 drp_val);
+
+		/* TXPI_CFG3 & TXPI_CFG4 */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_009C,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_009C_TXPI_CFG3_CFG4_MASK);
+		if (pll_clkout_mhz > XHDMIPHY_DRP_PLL_CLKOUT_RANGE8)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL1;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE9)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL2;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE10)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL3;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE11)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL1;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE13)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL2;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE15)
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL3;
+		else
+			drp_val = XHDMIPHY_DRP_TXPI_CFG3_CFG4_VAL4;
+
+		drp_val = (drp_val << XHDMIPHY_DRP_TXPI_CFG3_CFG4_SHIFT) &
+			  XDRP_GTHE4_CHN_REG_009C_TXPI_CFG3_CFG4_MASK;
+		/* write new DRP register value for TXPI_CFG3 & TXPI_CFG4 */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_009C,
+					 drp_val);
+		/* TX_PI_BIASSET */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_00FB,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_00FB_TXPI_BIASSET_MASK);
+		if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE17)
+			drp_val |= XHDMIPHY_DRP_TXPI_BIASSET_VAL1 <<
+				   XHDMIPHY_DRP_TXPI_BIASSET_SHIFT;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE10)
+			drp_val |= XHDMIPHY_DRP_TXPI_BIASSET_VAL2 <<
+				   XHDMIPHY_DRP_TXPI_BIASSET_SHIFT;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE14)
+			drp_val |= XHDMIPHY_DRP_TXPI_BIASSET_VAL3 <<
+				   XHDMIPHY_DRP_TXPI_BIASSET_SHIFT;
+
+		/* write new DRP register value for TX_PI_BIASSET */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_00FB,
+					 drp_val);
+		/* CH_HSPMUX_TX */
+		status |= xhdmiphy_drprd(inst, chid, XDRP_GTHE4_CHN_REG_0116,
+					 &drp_val);
+		drp_val &= ~(XDRP_GTHE4_CHN_REG_0116_CH_TX_HSPMUX_MASK);
+
+		if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE17)
+			drp_val |= XHDMIPHY_DRP_CH_HSPMUX_VAL1 <<
+				   XHDMIPHY_DRP_CH_HSPMUX_SHIFT;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE10)
+			drp_val |= XHDMIPHY_DRP_CH_HSPMUX_VAL2 <<
+				   XHDMIPHY_DRP_CH_HSPMUX_SHIFT;
+		else if (pll_clkout_mhz >= XHDMIPHY_DRP_PLL_CLKOUT_RANGE14)
+			drp_val |= XHDMIPHY_DRP_CH_HSPMUX_VAL3 <<
+				   XHDMIPHY_DRP_CH_HSPMUX_SHIFT;
+		else
+			drp_val |= XHDMIPHY_DRP_CH_HSPMUX_VAL4 <<
+				   XHDMIPHY_DRP_CH_HSPMUX_SHIFT;
+
+		/* write new DRP register value for CH_HSPMUX_TX */
+		status |= xhdmiphy_drpwr(inst, chid, XDRP_GTHE4_CHN_REG_0116,
+					 drp_val);
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_set_gt_linerate_cfg - This function will set the TXRATE or RXRATE
+ * port to select the GT Wizard configuration
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for TX or RX
+ */
+static void xhdmiphy_set_gt_linerate_cfg(struct xhdmiphy_dev *inst,
+					 enum chid chid, enum dir dir)
+{
+	enum pll_type pll_type;
+	u32 reg_val, mask_val, shift_val, reg_off;
+	u16 lr_val;
+
+	pll_type = xhdmiphy_get_pll_type(inst, dir, XHDMIPHY_CHID_CH1);
+
+	if (pll_type == XHDMIPHY_PLL_LCPLL)
+		lr_val = inst->quad.lcpll.linerate_cfg;
+	else
+		lr_val = inst->quad.rpll.linerate_cfg;
+
+	if (dir == XHDMIPHY_DIR_TX) {
+		if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+			reg_off = XHDMIPHY_TX_RATE_CH12_REG;
+		else
+			reg_off = XHDMIPHY_TX_RATE_CH34_REG;
+
+		mask_val = XHDMIPHY_TX_RATE_MASK(chid);
+		shift_val = XHDMIPHY_TX_RATE_SHIFT(chid);
+	} else {
+		if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+			reg_off = XHDMIPHY_RX_RATE_CH12_REG;
+		else
+			reg_off = XHDMIPHY_RX_RATE_CH34_REG;
+
+		mask_val = XHDMIPHY_RX_RATE_MASK(chid);
+		shift_val = XHDMIPHY_RX_RATE_SHIFT(chid);
+	}
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val &= ~mask_val;
+	reg_val |= (lr_val << shift_val);
+	xhdmiphy_write(inst, reg_off, reg_val);
+}
+
+static u32 xhdmiphy_gtye5_rxch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	u8 val_cmp;
+
+	val_cmp = xhdmiphy_check_linerate_cfg(inst, chid, XHDMIPHY_DIR_RX);
+
+	if (!val_cmp) {
+		xhdmiphy_set_gt_linerate_cfg(inst, chid, XHDMIPHY_DIR_RX);
+	} else {
+		xhdmiphy_gt_mst_rst(inst, chid, XHDMIPHY_DIR_RX, true);
+		xhdmiphy_gt_mst_rst(inst, chid, XHDMIPHY_DIR_RX, false);
+	}
+
+	return 0;
+}
+
+static u32 xhdmiphy_gtye5_txch_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	u8 val_cmp;
+
+	/* Compare the current and next CFG values */
+	val_cmp = xhdmiphy_check_linerate_cfg(inst, chid, XHDMIPHY_DIR_TX);
+	if (!val_cmp) {
+		xhdmiphy_set_gt_linerate_cfg(inst, chid, XHDMIPHY_DIR_TX);
+	} else {
+		/* Toggle RX Master Reset */
+		xhdmiphy_gt_mst_rst(inst, chid, XHDMIPHY_DIR_TX, true);
+		xhdmiphy_gt_mst_rst(inst, chid, XHDMIPHY_DIR_TX, false);
+	}
+
+	return 0;
+}
+
+/**
+ * xhdmiphy_get_gt_linerate - This function will get the TXRATE or RXRATE port
+ * to select the GT Wizard configuration
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for TX or RX
+ *
+ * return:	returns linerate
+ */
+static u16 xhdmiphy_get_gt_linerate(struct xhdmiphy_dev *inst, enum chid chid,
+				    enum dir dir)
+{
+	u32 reg_val, mask_val, shift_val, reg_off;
+	u16 lr_val;
+
+	if (dir == XHDMIPHY_DIR_TX) {
+		if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+			reg_off = XHDMIPHY_TX_RATE_CH12_REG;
+		else
+			reg_off = XHDMIPHY_TX_RATE_CH34_REG;
+
+		mask_val = XHDMIPHY_TX_RATE_MASK(chid);
+		shift_val = XHDMIPHY_TX_RATE_SHIFT(chid);
+	} else {
+		if (chid == XHDMIPHY_CHID_CH1 || chid == XHDMIPHY_CHID_CH2)
+			reg_off = XHDMIPHY_RX_RATE_CH12_REG;
+		else
+			reg_off = XHDMIPHY_RX_RATE_CH34_REG;
+
+		mask_val = XHDMIPHY_RX_RATE_MASK(chid);
+		shift_val = XHDMIPHY_RX_RATE_SHIFT(chid);
+	}
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val &= mask_val;
+	lr_val = (u16)(reg_val >> shift_val);
+
+	return lr_val;
+}
+
+/**
+ * xhdmiphy_check_linerate_cfg - This function will check the current CFG
+ * setting and compare it with the next CFG value
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for TX or RX
+ *
+ * @return:	true if Current and Next CFG are the same
+ *		false if Current and Next CFG are different
+ */
+bool xhdmiphy_check_linerate_cfg(struct xhdmiphy_dev *inst, enum chid chid,
+				 enum dir dir)
+{
+	enum pll_type pll_type;
+	u16 cur_val, lr_val;
+
+	pll_type = xhdmiphy_get_pll_type(inst, dir, XHDMIPHY_CHID_CH1);
+
+	if (pll_type == XHDMIPHY_PLL_LCPLL)
+		lr_val = inst->quad.lcpll.linerate_cfg;
+	else
+		lr_val = inst->quad.rpll.linerate_cfg;
+
+	cur_val = xhdmiphy_get_gt_linerate(inst, chid, dir);
+	if (cur_val != lr_val)
+		return false;
+
+	return true;
+}
+
+const struct gt_conf gthe4_conf = {
+	.cfg_set_cdr = xhdmiphy_gthe4_set_cdr,
+	.check_pll_oprange = xhdmiphy_gthe4_check_pll_oprange,
+	.outdiv_ch_reconf = xhdmiphy_gthe4_outdiv_chreconf,
+	.clk_ch_reconf = xhdmiphy_gthe4_clkch_reconf,
+	.clk_cmn_reconf = xhdmiphy_gthe4_clkcmn_reconf,
+	.rxch_reconf = xhdmiphy_gthe4_rxch_reconf,
+	.txch_reconf = xhdmiphy_gthe4_txch_reconf,
+
+	 .cpll_divs = {
+		.m = gthe4_cpll_divs_m,
+		.n1 = gthe4_cpll_divs_n1,
+		.n2 = gthe4_cpll_divs_n2,
+		.d = gthe4_cpll_divs_d,
+	},
+	.qpll_divs = {
+		.m = gthe4_qpll_divs_m,
+		.n1 = gthe4_qpll_divs_n1,
+		.n2 = gthe4_qpll_divs_n2,
+		.d = gthe4_qpll_divs_d,
+	},
+};
+
+const struct gt_conf gtye5_conf = {
+	.rxch_reconf = xhdmiphy_gtye5_rxch_reconf,
+	.txch_reconf = xhdmiphy_gtye5_txch_reconf,
+	.cpll_divs = {
+		.m = NULL,
+		.n1 = NULL,
+		.n2 = NULL,
+		.d = NULL,
+	},
+	.qpll_divs = {
+		.m = NULL,
+		.n1 = NULL,
+		.n2 = NULL,
+		.d = NULL,
+	},
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xhdmiphy_mmcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xhdmiphy_mmcm.c
@@ -0,0 +1,1862 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/string.h>
+#include "xhdmiphy.h"
+
+struct gthdmi_chars {
+	u64 dru_linerate;
+	u64 tx_mmcm_fvcomin;
+	u64 tx_mmcm_fvcomax;
+	u64 rx_mmcm_fvcomin;
+	u64 rx_mmcm_fvcomax;
+	u32 qpll0_refclk_min;
+	u32 qpll1_refclk_min;
+	u32 cpll_refclk_min;
+	u16 tx_mmcm_scale;
+	u16 rx_mmcm_scale;
+	u16 pll_scale;
+};
+
+static const struct gthdmi_chars gthe4hdmi_chars = {
+	.dru_linerate = XHDMIPHY_HDMI_GTHE4_DRU_LRATE,
+	.pll_scale = XHDMIPHY_HDMI_GTHE4_PLL_SCALE,
+	.qpll0_refclk_min = XHDMIPHY_HDMI_GTHE4_QPLL0_REFCLK_MIN,
+	.qpll1_refclk_min = XHDMIPHY_HDMI_GTHE4_QPLL1_REFCLK_MIN,
+	.cpll_refclk_min = XHDMIPHY_HDMI_GTHE4_CPLL_REFCLK_MIN,
+	.tx_mmcm_scale = XHDMIPHY_HDMI_GTHE4_TX_MMCM_SCALE,
+	.tx_mmcm_fvcomin = XHDMIPHY_HDMI_GTHE4_TX_MMCM_FVCO_MIN,
+	.tx_mmcm_fvcomax = XHDMIPHY_HDMI_GTHE4_TX_MMCM_FVCO_MAX,
+	.rx_mmcm_scale = XHDMIPHY_HDMI_GTHE4_RX_MMCM_SCALE,
+	.rx_mmcm_fvcomin = XHDMIPHY_HDMI_GTHE4_RX_MMCM_FVCO_MIN,
+	.rx_mmcm_fvcomax = XHDMIPHY_HDMI_GTHE4_RX_MMCM_FVCO_MAX,
+};
+
+static const struct gthdmi_chars gtye4hdmi_chars = {
+	.dru_linerate = XHDMIPHY_HDMI_GTYE4_DRU_LRATE,
+	.pll_scale = XHDMIPHY_HDMI_GTYE4_PLL_SCALE,
+	.qpll0_refclk_min = XHDMIPHY_HDMI_GTYE4_QPLL0_REFCLK_MIN,
+	.qpll1_refclk_min = XHDMIPHY_HDMI_GTYE4_QPLL1_REFCLK_MIN,
+	.cpll_refclk_min = XHDMIPHY_HDMI_GTYE4_CPLL_REFCLK_MIN,
+	.tx_mmcm_scale = XHDMIPHY_HDMI_GTYE4_TX_MMCM_SCALE,
+	.tx_mmcm_fvcomin = XHDMIPHY_HDMI_GTYE4_TX_MMCM_FVCO_MIN,
+	.tx_mmcm_fvcomax = XHDMIPHY_HDMI_GTYE4_TX_MMCM_FVCO_MAX,
+	.rx_mmcm_scale = XHDMIPHY_HDMI_GTYE4_RX_MMCM_SCALE,
+	.rx_mmcm_fvcomin = XHDMIPHY_HDMI_GTYE4_RX_MMCM_FVCO_MIN,
+	.rx_mmcm_fvcomax = XHDMIPHY_HDMI_GTYE4_RX_MMCM_FVCO_MAX,
+};
+
+static const struct gthdmi_chars gtye5hdmi_chars = {
+	.dru_linerate = XHDMIPHY_HDMI_GTYE5_DRU_LRATE,
+	.pll_scale = XHDMIPHY_HDMI_GTYE5_PLL_SCALE,
+	.qpll0_refclk_min = XHDMIPHY_HDMI_GTYE5_LCPLL_REFCLK_MIN,
+	.qpll1_refclk_min = XHDMIPHY_HDMI_GTYE5_RPLL_REFCLK_MIN,
+	.cpll_refclk_min = 0,
+	.tx_mmcm_scale = XHDMIPHY_HDMI_GTYE5_TX_MMCM_SCALE,
+	.tx_mmcm_fvcomin = XHDMIPHY_HDMI_GTYE5_TX_MMCM_FVCO_MIN,
+	.tx_mmcm_fvcomax = XHDMIPHY_HDMI_GTYE5_TX_MMCM_FVCO_MAX,
+	.rx_mmcm_scale = XHDMIPHY_HDMI_GTYE5_RX_MMCM_SCALE,
+	.rx_mmcm_fvcomin = XHDMIPHY_HDMI_GTYE5_RX_MMCM_FVCO_MIN,
+	.rx_mmcm_fvcomax = XHDMIPHY_HDMI_GTYE5_RX_MMCM_FVCO_MAX,
+};
+
+/*
+ * Following are the MMCM Parameter values for each rate.
+ * Based on the MAX rate config in PHY the MMCM
+ * should be programmed to generate the vid clk in
+ * FRL mode
+ */
+static struct xhdmiphy_mmcm gthe4_gtye4_mmcm[] = {
+	{0, 3, 1, 8, 8, 8}, /* 3x3 G -> 150Mhz */
+	{1, 49, 16, 7, 7, 7}, /* 6x3 G -> 175Mhz */
+	{2, 54, 16, 6, 6, 6}, /* 6x4 G -> 225Mhz */
+	{3, 3, 1, 4, 4, 4}, /* 8 G -> 300Mhz */
+	{4, 15, 4, 4, 4, 4}, /* 10 G -> 375Mhz */
+	{5, 3, 1, 3, 3, 3} /* 12 G -> (400 * 3/1) / 3 -> 400Mhz */
+};
+
+static struct xhdmiphy_mmcm gtye5_mmcm[] = {
+	{0, 3, 1, 8, 8, 8}, /* 12 G -> (400 * 3/1) / 3 -> 400Mhz */
+	{1, 49, 16, 7, 7, 7}, /* 10 G -> 375Mhz */
+	{2, 54, 16, 6, 6, 6}, /* 8 G -> 300Mhz */
+	{3, 3, 1, 4, 4, 4}, /* 6x4 G -> 225Mhz */
+	{4, 15, 4, 4, 4, 4}, /* 6x3 G -> 175Mhz */
+	{5, 3, 1, 3, 3, 3} /* 3x3 G -> 150Mhz */
+};
+
+static u16 mmcme4_lockreg1_enc[37] = {0x0, 0x03e8, 0x03e8, 0x03e8, 0x03e8,
+				      0x03e8, 0x03e8, 0x03e8, 0x03e8, 0x03e8,
+				      0x03e8, 0x0384, 0x0339, 0x02ee, 0x02bc,
+				      0x028a, 0x0271, 0x023f, 0x0226, 0x020d,
+				      0x01f4, 0x01db, 0x01c2, 0x01a9, 0x0190,
+				      0x0190, 0x0177, 0x015e, 0x015e, 0x0145,
+				      0x0145, 0x012c, 0x012c, 0x012c, 0x0113,
+				      0x0113, 0x0113};
+
+static u16 mmcme4_lockreg2_enc[11] = {0x7c01, 0x1801, 0x1801, 0x2001, 0x2c01,
+				      0x3801, 0x4401, 0x4c01, 0x5801, 0x6401,
+				      0x7001};
+
+static u16 mmcme4_lockreg3_enc[11] = {0x7fe9, 0x1be9, 0x1be9, 0x23e9, 0x2fe9,
+				      0x3be9, 0x47e9, 0x4fe9, 0x5be9, 0x67e9,
+				      0x73e9};
+
+static struct xhdmiphy_mmcm *get_mmcm_conf(struct xhdmiphy_dev *inst)
+{
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+		return gthe4_gtye4_mmcm;
+
+	return gtye5_mmcm;
+}
+
+static const struct gthdmi_chars *get_gthdmi_ptr(struct xhdmiphy_dev *inst)
+{
+	if (inst->conf.gt_type == XHDMIPHY_GTHE4)
+		return &gthe4hdmi_chars;
+	else if (inst->conf.gt_type == XHDMIPHY_GTYE4)
+		return &gtye4hdmi_chars;
+	else if (inst->conf.gt_type == XHDMIPHY_GTYE5)
+		return &gtye5hdmi_chars;
+
+	return NULL;
+}
+
+/**
+ * xhdmiphy_mmcme5_div_enc - This function returns the DRP encoding of
+ * clkfbout_mult optimized for: Phase = 0; Dutycycle = 0.5; No Fractional
+ * division. The calculations are based on XAPP888
+ *
+ * @div_type:	divider type to be encoded
+ * @div:	div is the divider to be encoded
+ *
+ * @return:	- Encoded Value for clk_reg1 [15: 0]
+ *		- Encoded Value for clk_reg2 [31:16]
+ */
+static u32 xhdmiphy_mmcme5_div_enc(enum mmcm_divs div_type, u16 div)
+{
+	u32 clk_reg1, clk_reg2;
+	u16 divde = div;
+	u8 hi_time, lo_time;
+
+	if (div_type == XHDMIPHY_MMCM_CLKOUT_DIVIDE) {
+		if (div % 2)
+			divde = (div / 2);
+		else
+			divde = (div / 2) + (div % 2);
+	}
+
+	hi_time = divde / 2;
+	lo_time = hi_time;
+
+	clk_reg2 = lo_time & 0xff;
+	clk_reg2 |= (hi_time & 0xff) << 8;
+
+	if (div_type == XHDMIPHY_MMCM_CLKFBOUT_MULT_F) {
+		clk_reg1 = (divde % 2) ? 0x00001700 : 0x00001600;
+	} else {
+		if (div % 2)
+			clk_reg1 = (divde % 2) ? 0x0000bb00 : 0x0000ba00;
+		else
+			clk_reg1 = (divde % 2) ? 0x00001b00 : 0x00001a00;
+	}
+
+	return (clk_reg2 << 16) | clk_reg1;
+}
+
+/**
+ * xhdmiphy_mmcme5_cpres_enc - This function returns the DRP encoding of CP and
+ * Res optimized for: Phase = 0; Dutycycle = 0.5; BW = low; No Fractional
+ * division
+ *
+ * @mult:	mult is the divider to be encoded
+ *
+ * @return:	- [3:0] CP
+ *		- [20:17] RES
+ *
+ * note: For more details about DRP encoding values , refer GT user guide
+ */
+static u32 xhdmiphy_mmcme5_cpres_enc(u16 mult)
+{
+	u16 cp, res;
+
+	switch (mult) {
+	case 4:
+		cp = 5; res = 15;
+	break;
+	case 5:
+		cp = 6; res = 15;
+	break;
+	case 6:
+		cp = 7; res = 15;
+	break;
+	case 7:
+		cp = 13; res = 15;
+	break;
+	case 8:
+		cp = 14; res = 15;
+	break;
+	case 9:
+		cp = 15; res = 15;
+	break;
+	case 10:
+		cp = 14; res = 7;
+	break;
+	case 11:
+		cp = 15; res = 7;
+	break;
+	case 12 ... 13:
+		cp = 15; res = 11;
+	break;
+	case 14:
+		cp = 15; res = 13;
+	break;
+	case 15:
+		cp = 15; res = 3;
+	break;
+	case 16 ... 17:
+		cp = 14; res = 5;
+	break;
+	case 18 ... 19:
+		cp = 15; res = 5;
+	break;
+	case 20 ... 21:
+		cp = 15; res = 9;
+		break;
+	case 22 ... 23:
+		cp = 14; res = 14;
+		break;
+	case 24 ... 26:
+		cp = 15; res = 14;
+		break;
+	case 27 ... 28:
+		cp = 14; res = 1;
+		break;
+	case 29 ... 33:
+		cp = 15; res = 1;
+		break;
+	case 34 ... 37:
+		cp = 14; res = 6;
+		break;
+	case 38 ... 44:
+		cp = 15; res = 6;
+		break;
+	case 45 ... 57:
+		cp = 15; res = 10;
+		break;
+	case 58 ... 63:
+		cp = 13; res = 12;
+		break;
+	case 64 ... 70:
+		cp = 14; res = 12;
+		break;
+	case 71 ... 86:
+		cp = 15; res = 12;
+		break;
+	case 87 ... 93:
+		cp = 14; res = 2;
+		break;
+	case 94:
+		cp = 5; res = 15;
+		break;
+	case 95:
+		cp = 6; res = 15;
+		break;
+	case 96:
+		cp = 7; res = 15;
+		break;
+	case 97:
+		cp = 13; res = 15;
+		break;
+	case 98:
+		cp = 14; res = 15;
+		break;
+	case 99:
+		cp = 15; res = 15;
+		break;
+	case 100:
+		cp = 14; res = 7;
+		break;
+	case 101:
+		cp = 15; res = 7;
+		break;
+	case 102 ... 103:
+		cp = 15; res = 11;
+		break;
+	case 104:
+		cp = 15; res = 13;
+		break;
+	case 105:
+		cp = 15; res = 3;
+		break;
+	case 106 ... 107:
+		cp = 14; res = 5;
+		break;
+	case 108 ... 109:
+		cp = 15; res = 5;
+		break;
+	case 110 ... 111:
+		cp = 15; res = 9;
+		break;
+	case 112 ... 113:
+		cp = 14; res = 14;
+		break;
+	case 114 ... 116:
+		cp = 15; res = 14;
+		break;
+	case 117 ... 118:
+		cp = 14; res = 1;
+		break;
+	case 119 ... 123:
+		cp = 15; res = 1;
+		break;
+	case 124 ... 127:
+		cp = 14; res = 6;
+		break;
+	case 128 ... 134:
+		cp = 15; res = 6;
+		break;
+	case 135 ... 147:
+		cp = 15; res = 10;
+		break;
+	case 148 ... 153:
+		cp = 13; res = 12;
+		break;
+	case 154 ... 160:
+		cp = 14; res = 12;
+		break;
+	case 161 ... 176:
+		cp = 15; res = 12;
+		break;
+	case 177 ... 183:
+		cp = 14; res = 2;
+		break;
+	case 184 ... 200:
+		cp = 14; res = 4;
+		break;
+	case 201 ... 273:
+		cp = 15; res = 4;
+		break;
+	case 274 ... 300:
+		cp = 13; res = 8;
+		break;
+	case 301 ... 325:
+		cp = 14; res = 8;
+		break;
+	case 326 ... 432:
+		cp = 15; res = 8;
+		break;
+	default:
+		cp = 13; res = 8;
+		break;
+	}
+
+	return ((res & 0xf) << 17) | ((cp & 0xf) | 0x160);
+}
+
+/**
+ * xhdmiphy_mmcme5_lockreg12_enc - This function returns the DRP encoding of
+ * lock Reg1 & Reg2 optimized for: Phase = 0; Dutycycle = 0.5; BW = low;
+ * No Fractional division
+ *
+ * @mult:	mult is the divider to be encoded
+ *
+ * @return:	- [15:0] lock_1 Reg
+ *		- [31:16] lock_2 Reg
+ *
+ * note: For more details about DRP encoding values , refer GT user guide
+ */
+static u32 xhdmiphy_mmcme5_lockreg12_enc(u16 mult)
+{
+	u16 lock_1, lock_2, lock_ref_dly, lock_fb_dly, lock_cnt;
+	u16 lock_sat_high = 9;
+
+	switch (mult) {
+	case 4:
+		lock_ref_dly = 4;
+		lock_fb_dly = 4;
+		lock_cnt = 1000;
+		break;
+	case 5:
+		lock_ref_dly = 6;
+		lock_fb_dly = 6;
+		lock_cnt = 1000;
+		break;
+	case 6 ... 7:
+		lock_ref_dly = 7;
+		lock_fb_dly = 7;
+		lock_cnt = 1000;
+		break;
+	case 8:
+		lock_ref_dly = 9;
+		lock_fb_dly = 9;
+		lock_cnt = 1000;
+		break;
+	case 9 ... 10:
+		lock_ref_dly = 10;
+		lock_fb_dly = 10;
+		lock_cnt = 1000;
+		break;
+	case 11:
+		lock_ref_dly = 11;
+		lock_fb_dly = 11;
+		lock_cnt = 1000;
+		break;
+	case 12:
+		lock_ref_dly = 13;
+		lock_fb_dly = 13;
+		lock_cnt = 1000;
+		break;
+	case 13 ... 14:
+		lock_ref_dly = 14;
+		lock_fb_dly = 14;
+		lock_cnt = 1000;
+		break;
+	case 15:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 900;
+		break;
+	case 16 ... 17:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 825;
+		break;
+	case 18:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 750;
+		break;
+	case 19 ... 20:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 700;
+		break;
+	case 21:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 650;
+		break;
+	case 22 ... 23:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 625;
+		break;
+	case 24:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 575;
+		break;
+	case 25:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 550;
+		break;
+	case 26 ... 28:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 525;
+		break;
+	case 29 ... 30:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 475;
+		break;
+	case 31:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 450;
+		break;
+	case 32 ... 33:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 425;
+		break;
+	case 34 ... 36:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 400;
+		break;
+	case 37:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 375;
+		break;
+	case 38 ... 40:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 350;
+		break;
+	case 41 ... 43:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 325;
+		break;
+	case 44 ... 47:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 300;
+		break;
+	case 48 ... 51:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 275;
+		break;
+	case 52 ... 205:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 950;
+		break;
+	case 206 ... 432:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 925;
+		break;
+	default:
+		lock_ref_dly = 16;
+		lock_fb_dly = 16;
+		lock_cnt = 250;
+		break;
+	}
+
+	lock_1 = ((lock_fb_dly & 0x1f) << 10) | (lock_cnt & 0x3ff);
+
+	lock_2 = ((lock_ref_dly & 0x1f) << 10) | (lock_sat_high & 0x3ff);
+
+	return (lock_2 << 16) | lock_1;
+}
+
+/**
+ * xhdmiphy_mmcme4_div_enc - This function returns the DRP encoding of
+ * clkfbout_mult optimized for: Phase = 0; Dutycycle = 0.5; No Fractional
+ * division The calculations are based on XAPP888
+ *
+ * @div_type:	div is the divider to be encoded
+ * @div:	divider value
+ *
+ * @return:	- Encoded Value for clk_reg1 [31: 0]
+ *		- Encoded Value for clk_reg2 [63:32]
+ */
+static u32 xhdmiphy_mmcme4_div_enc(enum mmcm_divs div_type, u8 div)
+{
+	u32 clk_reg1, clk_reg2;
+	u8 hi_time, lo_time;
+
+	if (div == 1) {
+		clk_reg1 = 0x00001041;
+		clk_reg2 = 0x00C00000;
+	} else {
+		hi_time = div / 2;
+		lo_time = div - hi_time;
+		clk_reg1 = lo_time & 0x3f;
+		clk_reg1 |= (hi_time & 0x3f) << 6;
+		clk_reg1 |= (div_type == XHDMIPHY_MMCM_DIVCLK_DIVIDE) ?
+							0x0000 : 0x1000;
+		clk_reg2 = (div % 2) ? 0x00800000 : 0x00000000;
+	}
+
+	return clk_reg2 | clk_reg1;
+}
+
+/**
+ * xhdmiphy_mmcme4_filtreg1_enc - This function returns the drp encoding of
+ * filtereg1 optimized for: phase = 0; dutycycle = 0.5; BW = low; no fractional
+ * division
+ *
+ * @mult:	mult is the divider to be encoded
+ *
+ * @return:	- encoded value
+ *
+ * note: For more details about DRP encoding values , refer GT user guide
+ */
+static u16 xhdmiphy_mmcme4_filtreg1_enc(u8 mult)
+{
+	u16 drp_enc;
+
+	switch (mult) {
+	case 1: case 2: case 3:
+	case 4: case 5: case 6:
+	case 7: case 8: case 9:
+	case 10: case 11: case 12:
+	case 13: case 14:
+	case 16:
+		drp_enc = 0x0900;
+		break;
+	case 15:
+		drp_enc = 0x1000;
+		break;
+		break;
+	case 17: case 19: case 20:
+	case 29: case 30: case 31:
+	case 38: case 39: case 40:
+	case 41: case 78: case 79:
+	case 80: case 81: case 82:
+	case 83: case 84:
+	case 85:
+		drp_enc = 0x9800;
+		break;
+	case 26: case 27: case 28:
+	case 71: case 72: case 73:
+	case 74: case 75: case 76:
+	case 77: case 120: case 121:
+	case 122: case 123: case 124:
+	case 125: case 126: case 127:
+	case 128:
+		drp_enc = 0x9100;
+		break;
+	default:
+		drp_enc = 0x9900;
+		break;
+	}
+
+	return drp_enc;
+}
+
+/**
+ * xhdmiphy_mmcme4_filtreg2_enc - This function returns the drp encoding of
+ * filter reg1 optimized for: phase = 0; dutycycle = 0.5; bw = low; no
+ * fractional division
+ *
+ * @mult:	mult is the divider to be encoded
+ *
+ * @return:	- encoded Value
+ *
+ * note: For more details about DRP encoding values , refer GT user guide
+ */
+static u16 xhdmiphy_mmcme4_filtreg2_enc(u8 mult)
+{
+	u16 drp_enc;
+
+	switch (mult) {
+	case 1: case 2:
+		drp_enc = 0x9990;
+	break;
+	case 3:
+		drp_enc = 0x9190;
+		break;
+	case 4:
+		drp_enc = 0x1190;
+		break;
+	case 5:
+		drp_enc = 0x8190;
+		break;
+	case 6: case 7:
+		drp_enc = 0x9890;
+		break;
+	case 8:
+		drp_enc = 0x0190;
+		break;
+	case 9: case 10: case 11:
+	case 15: case 17: case 18:
+		drp_enc = 0x1890;
+		break;
+	case 12: case 13: case 14:
+	case 19: case 20: case 21:
+	case 22: case 23: case 24:
+	case 25:
+		drp_enc = 0x8890;
+		break;
+	case 16: case 26: case 27:
+	case 28: case 29: case 30:
+	case 31: case 32: case 33:
+	case 34: case 35: case 36:
+	case 37:
+		drp_enc = 0x9090;
+		break;
+	case 38: case 39: case 40:
+	case 41: case 42: case 43:
+	case 44: case 45: case 46:
+	case 47: case 48: case 49:
+	case 50: case 51: case 52:
+	case 53: case 54: case 55:
+	case 56: case 57: case 58:
+	case 59: case 60: case 61:
+	case 62:
+		drp_enc = 0x0890;
+		break;
+	case 120: case 121: case 122:
+	case 123: case 124: case 125:
+	case 126: case 127: case 128:
+		drp_enc = 0x8090;
+		break;
+	default:
+		drp_enc = 0x1090;
+		break;
+	}
+
+	return drp_enc;
+}
+
+static u16 xhdmiphy_mmcme4_lockreg1_enc(u8 mult)
+{
+	u16 drp_enc;
+
+	if (mult >= 1 && mult <= 36)
+		drp_enc = mmcme4_lockreg1_enc[mult];
+	else
+		drp_enc = 0x00fa;
+
+	return drp_enc;
+}
+
+/**
+ * xhdmiphy_mmcme4_lockreg2_enc - This function returns the drp encoding of
+ * lockreg2 optimized for: phase = 0; dutycycle = 0.5; no fractional division
+ *
+ * @mult:	mult is the divider to be encoded
+ *
+ * @return:	- encoded Value
+ */
+static u16 xhdmiphy_mmcme4_lockreg2_enc(u8 mult)
+{
+	if (mult >= 1 && mult <= 10)
+		return mmcme4_lockreg2_enc[mult];
+
+	return mmcme4_lockreg2_enc[0];
+}
+
+static u16 xhdmiphy_mmcme4_lockreg3_enc(u8 mult)
+{
+	if (mult >= 1 && mult <= 10)
+		return mmcme4_lockreg3_enc[mult];
+
+	return mmcme4_lockreg3_enc[0];
+}
+
+/**
+ * xhdmiphy_wr_mmcm5_params - This function will write the mixed-mode clock
+ * manager (MMCM) values currently stored in the driver's instance structure to
+ * hardware
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ *
+ * @return:	- 0 if the MMCM write was successful
+ *		- 1 otherwise, if the configuration success bit did not go low
+ */
+static bool xhdmiphy_wr_mmcm5_params(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	struct xhdmiphy_mmcm *mmcm_params;
+	u32 drp_val32;
+	u16 drp_rdval;
+	u8 chid;
+
+	chid = (dir == XHDMIPHY_DIR_TX) ? XHDMIPHY_CHID_TXMMCM :
+		       XHDMIPHY_CHID_RXMMCM;
+
+	mmcm_params = &inst->quad.mmcm[dir];
+
+	/* check parameters if has been initialized */
+	if (!mmcm_params->divclk_divide && !mmcm_params->clkfbout_mult &&
+	    !mmcm_params->clkout0_div && !mmcm_params->clkout1_div &&
+	    !mmcm_params->clkout2_div)
+		return 1;
+
+	/* write CLKFBOUT_1 & CLKFBOUT_2 values */
+	drp_val32 = xhdmiphy_mmcme5_div_enc(XHDMIPHY_MMCM_CLKFBOUT_MULT_F,
+					    mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKFBOUT_1_REG,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM5_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKFBOUT_2_REG,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM5_WRITE_VAL));
+
+	/* write DIVCLK_DIVIDE & DESKEW_2 values */
+	drp_val32 = xhdmiphy_mmcme5_div_enc(XHDMIPHY_MMCM_DIVCLK_DIVIDE,
+					    mmcm_params->divclk_divide);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_DIVCLK_DIVIDE_REG,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM5_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_DESKEW_REG,
+		       ((mmcm_params->divclk_divide == 0) ? 0x0000 :
+		       ((mmcm_params->divclk_divide % 2) ? 0x0400 : 0x0000)));
+
+	/* write CLKOUT0_1 & CLKOUT0_2 values */
+	drp_val32 = xhdmiphy_mmcme5_div_enc(XHDMIPHY_MMCM_CLKOUT_DIVIDE,
+					    mmcm_params->clkout0_div);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKOUT0_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM5_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKOUT0_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM5_WRITE_VAL));
+
+	/* write CLKOUT1_1 & CLKOUT1_2 values */
+	drp_val32 = xhdmiphy_mmcme5_div_enc(XHDMIPHY_MMCM_CLKOUT_DIVIDE,
+					    mmcm_params->clkout1_div);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKOUT1_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM5_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKOUT1_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM5_WRITE_VAL));
+
+	/* write CLKOUT2_1 & CLKOUT2_2 values */
+	drp_val32 = xhdmiphy_mmcme5_div_enc(XHDMIPHY_MMCM_CLKOUT_DIVIDE,
+					    mmcm_params->clkout2_div);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKOUT2_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM5_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CLKOUT2_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM5_WRITE_VAL));
+
+	/* write CP & RES values */
+	drp_val32 = xhdmiphy_mmcme5_cpres_enc(mmcm_params->clkfbout_mult);
+	drp_rdval = xhdmiphy_drprd(inst, chid, XHDMIPHY_MMCM5_DRP_CP_REG1,
+				   &drp_rdval);
+	drp_rdval &= ~(XHDMIPHY_MMCM5_CP_RES_MASK);
+
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_CP_REG1,
+		       (u16)((drp_val32 & XHDMIPHY_MMCM5_CP_RES_MASK) |
+			     drp_rdval));
+
+	drp_rdval = xhdmiphy_drprd(inst, chid, XHDMIPHY_MMCM5_DRP_RES_REG1,
+				   &drp_rdval);
+	drp_rdval &= ~(XHDMIPHY_MMCM5_RES_MASK);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_RES_REG1,
+		       (u16)(((drp_val32 >> 15) & XHDMIPHY_MMCM5_RES_MASK) |
+			      drp_rdval));
+
+	/* write lock reg1 & reg2 values */
+	drp_val32 = xhdmiphy_mmcme5_lockreg12_enc(mmcm_params->clkfbout_mult);
+	/* lock_1 */
+	drp_rdval = xhdmiphy_drprd(inst, chid, XHDMIPHY_MMCM5_DRP_LOCK_REG1,
+				   &drp_rdval);
+	drp_rdval &= ~(XHDMIPHY_MMCM5_LOCK1_MASK1);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_LOCK_REG1,
+		       (u16)((drp_val32 & XHDMIPHY_MMCM5_LOCK1_MASK2) |
+			     drp_rdval));
+
+	/* lock_2 */
+	drp_rdval = xhdmiphy_drprd(inst, chid, XHDMIPHY_MMCM5_DRP_LOCK_REG2,
+				   &drp_rdval);
+	drp_rdval &= ~(XHDMIPHY_MMCM5_LOCK1_MASK1);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM5_DRP_LOCK_REG2,
+		       (u16)(((drp_val32 >> 16) & XHDMIPHY_MMCM5_LOCK1_MASK2) |
+			     drp_rdval));
+
+	return 0;
+}
+
+/**
+ * xhdmiphy_wr_mmcm4_params - This function will write the mixed-mode clock
+ * manager (mmcm) values currently stored in the driver's instance structure
+ * to hardware .
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for tX or rX
+ *
+ * @return:	- 0 if the mmcm write was successful
+ *		- 1 otherwise, if the configuration success bit did not go low
+ */
+static bool xhdmiphy_wr_mmcm4_params(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	struct xhdmiphy_mmcm *mmcm_params;
+	u32 drp_val32;
+	u16 drp_val;
+	u8 chid;
+
+	chid = (dir == XHDMIPHY_DIR_TX) ? XHDMIPHY_CHID_TXMMCM :
+					  XHDMIPHY_CHID_RXMMCM;
+	mmcm_params = &inst->quad.mmcm[dir];
+
+	if (!mmcm_params->divclk_divide && !mmcm_params->clkfbout_mult &&
+	    !mmcm_params->clkout0_div && !mmcm_params->clkout1_div &&
+	    !mmcm_params->clkout2_div) {
+		return 1;
+	}
+
+	/* write power register Value */
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_PWR_REG,
+		       XHDMIPHY_MMCM4_WRITE_VAL);
+
+	/* write CLKFBOUT reg1 & reg2 values */
+	drp_val32 = xhdmiphy_mmcme4_div_enc(XHDMIPHY_MMCM_CLKFBOUT_MULT_F,
+					    mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKFBOUT_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM4_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKFBOUT_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM4_WRITE_VAL));
+
+	/* write gg value */
+	drp_val32 = xhdmiphy_mmcme4_div_enc(XHDMIPHY_MMCM_DIVCLK_DIVIDE,
+					    mmcm_params->divclk_divide);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_DIVCLK_DIV_REG,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM4_WRITE_VAL));
+
+	/* write CLKOUT0 reg1 & reg2 values */
+	drp_val32 = xhdmiphy_mmcme4_div_enc(XHDMIPHY_MMCM_CLKOUT_DIVIDE,
+					    mmcm_params->clkout0_div);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKOUT0_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM4_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKOUT0_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM4_WRITE_VAL));
+
+	drp_val32 = xhdmiphy_mmcme4_div_enc(XHDMIPHY_MMCM_CLKOUT_DIVIDE,
+					    mmcm_params->clkout1_div);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKOUT1_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM4_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKOUT1_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM4_WRITE_VAL));
+
+	drp_val32 = xhdmiphy_mmcme4_div_enc(XHDMIPHY_MMCM_CLKOUT_DIVIDE,
+					    mmcm_params->clkout2_div);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKOUT2_REG1,
+		       (u16)(drp_val32 & XHDMIPHY_MMCM4_WRITE_VAL));
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_CLKOUT2_REG2,
+		       (u16)((drp_val32 >> 16) & XHDMIPHY_MMCM4_WRITE_VAL));
+
+	drp_val = xhdmiphy_mmcme4_lockreg1_enc(mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_DRP_LOCK_REG1, drp_val);
+
+	drp_val = xhdmiphy_mmcme4_lockreg2_enc(mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_DRP_LOCK_REG2, drp_val);
+
+	drp_val = xhdmiphy_mmcme4_lockreg3_enc(mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_DRP_LOCK_REG3, drp_val);
+
+	drp_val = xhdmiphy_mmcme4_filtreg1_enc(mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_DRP_FILTER_REG1, drp_val);
+
+	drp_val = xhdmiphy_mmcme4_filtreg2_enc(mmcm_params->clkfbout_mult);
+	xhdmiphy_drpwr(inst, chid, XHDMIPHY_MMCM4_DRP_FILTER_REG2, drp_val);
+
+	return 0;
+}
+
+void xhdmiphy_mmcm_start(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	struct xhdmiphy_mmcm *mmcm_ptr;
+
+	if (dir == XHDMIPHY_DIR_RX)
+		mmcm_ptr = &inst->quad.rx_mmcm;
+	else
+		mmcm_ptr = &inst->quad.tx_mmcm;
+
+	/* check values if valid */
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		if (!(mmcm_ptr->clkout0_div > 0 &&
+		      mmcm_ptr->clkout0_div <= 128 &&
+		      mmcm_ptr->clkout1_div > 0 &&
+		      mmcm_ptr->clkout1_div <= 128 &&
+		      mmcm_ptr->clkout2_div > 0 &&
+		      mmcm_ptr->clkout2_div <= 128))
+			return;
+	} else {
+		if (!(mmcm_ptr->clkout0_div > 0 &&
+		      mmcm_ptr->clkout0_div <= 432 &&
+		      mmcm_ptr->clkout1_div > 0 &&
+		      mmcm_ptr->clkout1_div <= 432 &&
+		      mmcm_ptr->clkout2_div > 0 &&
+		      mmcm_ptr->clkout2_div <= 432))
+			return;
+	}
+
+	xhdmiphy_mmcm_reset(inst, dir, true);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+		xhdmiphy_wr_mmcm4_params(inst, dir);
+	else
+		xhdmiphy_wr_mmcm5_params(inst, dir);
+
+	xhdmiphy_mmcm_reset(inst, dir, false);
+	xhdmiphy_mmcm_lock_en(inst, dir, false);
+}
+
+/**
+ * xhdmiphy_mmcm_lock_en - This function will reset the mixed-mode clock
+ * manager (MMCM) core.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @enable:	Enable is an indicator whether to "Enable" the locked mask
+ *		if set to 1. If set to 0: reset, then disable
+ */
+void xhdmiphy_mmcm_lock_en(struct xhdmiphy_dev *inst, enum dir dir, u8 enable)
+{
+	u32 reg_off, reg_val;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_MMCM_TXUSRCLK_CTRL_REG;
+	else
+		reg_off = XHDMIPHY_MMCM_RXUSRCLK_CTRL_REG;
+
+	/* Assert reset */
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val |= XHDMIPHY_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK;
+	xhdmiphy_write(inst, reg_off, reg_val);
+
+	if (!enable) {
+		/* De-assert reset */
+		reg_val &= ~XHDMIPHY_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK;
+		xhdmiphy_write(inst, reg_off, reg_val);
+	}
+}
+
+/**
+ * xhdmiphy_mmcm_param - This function sets the MMCM programming values based
+ * on max rate
+ *
+ * @inst:	inst is a pointer to the Hdmiphy core instance.
+ * @dir:	dir is an indicator for RX or TX.
+ *
+ * @return:	none
+ *
+ * note:	based on the MAX Rate set in the GUI, the MMCM values are
+ *		selected.
+ *		3 -> Max Rate selected in GUI is 3G
+ *		6 -> Max Rate selected in GUI is 6G
+ *		8 -> Max Rate selected in GUI is 8G
+ *		10 -> Max Rate selected in GUI is 10G
+ *		12 -> Max Rate selected in GUI in 12G
+ */
+void xhdmiphy_mmcm_param(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	struct xhdmiphy_mmcm *mmcm_ptr, *conf;
+	u8 maxrate, num;
+
+	if (dir == XHDMIPHY_DIR_RX) {
+		mmcm_ptr = &inst->quad.rx_mmcm;
+		maxrate = inst->conf.rx_maxrate;
+		num = inst->conf.rx_channels;
+	} else {
+		mmcm_ptr = &inst->quad.tx_mmcm;
+		maxrate = inst->conf.tx_maxrate;
+		num = inst->conf.tx_channels;
+	}
+
+	conf = get_mmcm_conf(inst);
+
+	switch (maxrate) {
+	case 3:
+		mmcm_ptr->clkfbout_mult = conf[0].clkfbout_mult;
+		mmcm_ptr->divclk_divide = conf[0].divclk_divide;
+		mmcm_ptr->clkout0_div = conf[0].clkout0_div;
+		mmcm_ptr->clkout1_div = conf[0].clkout1_div;
+		mmcm_ptr->clkout2_div = conf[0].clkout2_div;
+		break;
+	case 6:
+		if (num == 3) {
+			mmcm_ptr->clkfbout_mult = conf[1].clkfbout_mult;
+			mmcm_ptr->divclk_divide = conf[1].divclk_divide;
+			mmcm_ptr->clkout0_div = conf[1].clkout0_div;
+			mmcm_ptr->clkout1_div = conf[1].clkout1_div;
+			mmcm_ptr->clkout2_div = conf[1].clkout2_div;
+		} else {
+			mmcm_ptr->clkfbout_mult = conf[2].clkfbout_mult;
+			mmcm_ptr->divclk_divide = conf[2].divclk_divide;
+			mmcm_ptr->clkout0_div = conf[2].clkout0_div;
+			mmcm_ptr->clkout1_div = conf[2].clkout1_div;
+			mmcm_ptr->clkout2_div = conf[2].clkout2_div;
+		}
+		break;
+	case 8:
+		mmcm_ptr->clkfbout_mult = conf[3].clkfbout_mult;
+		mmcm_ptr->divclk_divide = conf[3].divclk_divide;
+		mmcm_ptr->clkout0_div = conf[3].clkout0_div;
+		mmcm_ptr->clkout1_div = conf[3].clkout1_div;
+		mmcm_ptr->clkout2_div = conf[3].clkout2_div;
+		break;
+	case 10:
+		mmcm_ptr->clkfbout_mult = conf[4].clkfbout_mult;
+		mmcm_ptr->divclk_divide = conf[4].divclk_divide;
+		mmcm_ptr->clkout0_div = conf[4].clkout0_div;
+		mmcm_ptr->clkout1_div = conf[4].clkout1_div;
+		mmcm_ptr->clkout2_div = conf[4].clkout2_div;
+		break;
+	case 12:
+		mmcm_ptr->clkfbout_mult = conf[5].clkfbout_mult;
+		mmcm_ptr->divclk_divide = conf[5].divclk_divide;
+		mmcm_ptr->clkout0_div = conf[5].clkout0_div;
+		mmcm_ptr->clkout1_div = conf[5].clkout1_div;
+		mmcm_ptr->clkout2_div = conf[5].clkout2_div;
+		break;
+	default:
+		break;
+	}
+}
+
+static void xhdmiphy_set_clkout2_div(struct xhdmiphy_dev *inst, enum dir dir,
+				     u64 linerate, struct xhdmiphy_mmcm *mmcm_ptr)
+{
+	/* Only do this when the clkout2_div has been set */
+	if (mmcm_ptr->clkout2_div) {
+		if (dir == XHDMIPHY_DIR_RX) {
+			/* Correct divider value if TMDS clock ratio is 1/40 */
+			if (inst->rx_tmdsclock_ratio) {
+				if ((mmcm_ptr->clkout2_div % 4) == 0) {
+					mmcm_ptr->clkout2_div =
+					mmcm_ptr->clkout2_div / 4;
+				} else {
+				/*
+				 * Not divisible by 4: repeat
+				 * loop with a lower multiply
+				 * value
+				 */
+					if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+						mmcm_ptr->clkout2_div = 255;
+					else
+						mmcm_ptr->clkout2_div = 65535;
+				}
+			}
+		}
+		/* TX */
+		else if ((((linerate / 1000000) >= XHDMIPHY_LRATE_3400) &&
+			  (inst->tx_samplerate == 1)) ||
+			  (((linerate / 1000000) / inst->tx_samplerate) >=
+			    XHDMIPHY_LRATE_3400)) {
+			if ((mmcm_ptr->clkout2_div % 4) == 0) {
+				mmcm_ptr->clkout2_div = mmcm_ptr->clkout2_div / 4;
+			} else {
+			/*
+			 * Not divisible by 4: repeat loop with
+			 * a lower multiply value
+			 */
+				if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+					mmcm_ptr->clkout2_div = 255;
+				else
+					mmcm_ptr->clkout2_div = 65535;
+			}
+		}
+	}
+}
+
+/**
+ * xhdmiphy_cal_mmcm_param - This function calculates the HDMI mmcm parameters.
+ *
+ * @inst:	inst is a pointer to the Hdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for RX or TX
+ * @ppc:	ppc specifies the total number of pixels per clock
+ *		- 1 = XVIDC_PPC_1
+ *		- 2 = XVIDC_PPC_2
+ *		- 4 = XVIDC_PPC_4
+ * @bpc:	bpc specifies the color depth/bits per color component
+ *		- 6 = XVIDC_BPC_6
+ *		- 8 = XVIDC_BPC_8
+ *		- 10 = XVIDC_BPC_10
+ *		- 12 = XVIDC_BPC_12
+ *		- 16 = XVIDC_BPC_16
+ *
+ * @return:	- 0 if calculated PLL parameters updated successfully
+ *		- 1 if parameters not updated
+ */
+u32 xhdmiphy_cal_mmcm_param(struct xhdmiphy_dev *inst, enum chid chid,
+			    enum dir dir, enum ppc ppc, enum color_depth bpc)
+{
+	struct xhdmiphy_mmcm *mmcm_ptr;
+	enum pll_type pll_type;
+	u64 linerate = 0;
+	u32 refclk, div, mult;
+	u16 mult_div;
+	u8 valid;
+
+	pll_type = xhdmiphy_get_pll_type(inst, dir, XHDMIPHY_CHID_CH1);
+
+	switch (pll_type) {
+	case XHDMIPHY_PLL_QPLL:
+	case XHDMIPHY_PLL_QPLL0:
+	case XHDMIPHY_PLL_LCPLL:
+		linerate = inst->quad.cmn0.linerate;
+		break;
+	case XHDMIPHY_PLL_QPLL1:
+	case XHDMIPHY_PLL_RPLL:
+		linerate = inst->quad.cmn1.linerate;
+		break;
+	default:
+		linerate = inst->quad.ch1.linerate;
+		break;
+	}
+
+	if (((linerate / 1000000) > 2970) && ppc == XVIDC_PPC_1) {
+		dev_err(inst->dev, "ppc not supported\n");
+		return 1;
+	}
+
+	div = 1;
+	do {
+		if (dir == XHDMIPHY_DIR_RX) {
+			refclk = inst->rx_refclk_hz;
+			mmcm_ptr = &inst->quad.rx_mmcm;
+			refclk = refclk / (get_gthdmi_ptr(inst))->rx_mmcm_scale;
+			mult = (get_gthdmi_ptr(inst))->rx_mmcm_fvcomax * div / refclk;
+		} else {
+			refclk = inst->tx_refclk_hz;
+			mmcm_ptr = &inst->quad.tx_mmcm;
+			refclk = refclk / (get_gthdmi_ptr(inst))->tx_mmcm_scale;
+			mult = (get_gthdmi_ptr(inst))->tx_mmcm_fvcomax * div / refclk;
+		}
+
+		/* return if refclk is below valid range */
+		if (refclk < 20000000)
+			return (1);
+
+		/* in case of 4 pixels per clock, the M must be a multiple of four */
+		if (ppc == XVIDC_PPC_4) {
+			mult = mult / 4;
+			mult = mult * 4;
+		} else if (ppc == XVIDC_PPC_2) {
+		/* else the M must be a multiple of two */
+			mult = mult / 2;
+			mult = mult * 2;
+		}
+
+		valid = (false);
+		do {
+			mult_div = mult / div;
+			mmcm_ptr->clkfbout_mult = mult;
+			mmcm_ptr->divclk_divide = div;
+			if (inst->conf.transceiver_width == 4) {
+				/* link clock: TMDS clock ratio 1/40 */
+				if ((linerate / 1000000) >= XHDMIPHY_LRATE_3400) {
+					if (dir == XHDMIPHY_DIR_TX &&
+					    (((linerate / 1000000) / inst->tx_samplerate) < 3400)) {
+						mmcm_ptr->clkout0_div = mult_div * 4;
+					} else {
+						mmcm_ptr->clkout0_div = mult_div;
+					}
+				} else {
+				/* link clock: TMDS clock ratio 1/10 */
+					mmcm_ptr->clkout0_div = mult_div * 4;
+				}
+			} else {
+				/* 2 Byte Mode */
+				/* link clock: TMDS clock ratio 1/40 */
+				if ((linerate / 1000000) >= XHDMIPHY_LRATE_3400) {
+					if (dir == XHDMIPHY_DIR_TX &&
+					    (((linerate / 1000000) / inst->tx_samplerate) < 3400)) {
+						mmcm_ptr->clkout0_div = mult_div * 2;
+					} else {
+						mmcm_ptr->clkout0_div = mult_div / 2;
+					}
+				} else {
+				/* link clock: TMDS clock ratio 1/10 */
+					mmcm_ptr->clkout0_div = mult_div * 2;
+				}
+			}
+			/* TMDS clock */
+			mmcm_ptr->clkout1_div = mult_div *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1);
+			/* video clock */
+			mmcm_ptr->clkout2_div = 0;
+			switch (bpc) {
+			case XVIDC_BPC_10:
+				/* quad pixel */
+				if (ppc == (XVIDC_PPC_4)) {
+					mmcm_ptr->clkout2_div = (mult_div * 5 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				/* dual pixel */
+				} else if (ppc == (XVIDC_PPC_2)) {
+					/*
+					 * The clock ratio is 2.5. The PLL only
+					 * supports integer value. The mult_div
+					 * must be dividable by two
+					 * (2 * 2.5 = 5) to get an integer
+					 * number
+					 */
+					if ((mult_div % 2) == 0) {
+						mmcm_ptr->clkout2_div =
+							(mult_div * 5 / 2 *
+							((dir == XHDMIPHY_DIR_TX) ?
+							(inst->tx_samplerate) : 1));
+					}
+				/* single pixel */
+				} else {
+					/*
+					 * The clock ratio is 1.25. The pll only
+					 * supports integer values The multDiv
+					 * must be dividable by four
+					 * (4 * 1.25 = 5) to get an integer
+					 * number
+					 */
+					if ((mult_div % 4) == 0) {
+						mmcm_ptr->clkout2_div = (mult_div * 5 / 4 *
+							((dir == XHDMIPHY_DIR_TX) ?
+							(inst->tx_samplerate) : 1));
+					}
+				}
+				break;
+			case XVIDC_BPC_12:
+				/* quad pixel */
+				if (ppc == (XVIDC_PPC_4)) {
+					mmcm_ptr->clkout2_div = (mult_div * 6 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				} else if (ppc == (XVIDC_PPC_2)) {
+				/* dual pixel */
+					mmcm_ptr->clkout2_div = (mult_div * 3 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				/* single pixel */
+				} else {
+					/*
+					 * The clock ratio is 1.5. The PLL only
+					 * supports integer values. The mult_div
+					 * must be dividable by two (2 * 1.5 = 3)
+					 * to get an integer number
+					 */
+					if ((mult_div % 2) == 0) {
+						mmcm_ptr->clkout2_div = (mult_div * 3 / 2 *
+							((dir == XHDMIPHY_DIR_TX) ?
+							(inst->tx_samplerate) : 1));
+					}
+				}
+				break;
+			case XVIDC_BPC_16:
+				/* quad pixel */
+				if (ppc == (XVIDC_PPC_4)) {
+					mmcm_ptr->clkout2_div = (mult_div * 8 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				} else if (ppc == (XVIDC_PPC_2)) {
+				/* dual pixel */
+					mmcm_ptr->clkout2_div = (mult_div * 4 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				} else {
+				/* single pixel */
+					mmcm_ptr->clkout2_div = (mult_div * 2 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				}
+				break;
+			case XVIDC_BPC_8:
+			default:
+				/* quad pixel */
+				if (ppc == (XVIDC_PPC_4)) {
+					mmcm_ptr->clkout2_div = (mult_div * 4 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				} else if (ppc == (XVIDC_PPC_2)) {
+				/* dual pixel */
+					mmcm_ptr->clkout2_div = (mult_div * 2 *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				} else {
+				/* single pixel */
+					mmcm_ptr->clkout2_div = (mult_div *
+						((dir == XHDMIPHY_DIR_TX) ?
+						(inst->tx_samplerate) : 1));
+				}
+				break;
+			}
+			xhdmiphy_set_clkout2_div(inst, dir, linerate, mmcm_ptr);
+
+			/* Check values */
+			if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+				if (mmcm_ptr->clkout0_div > 0 &&
+				    mmcm_ptr->clkout0_div <= 128 &&
+				    mmcm_ptr->clkout1_div > 0 &&
+				    mmcm_ptr->clkout1_div <= 128 &&
+				    mmcm_ptr->clkout2_div > 0 &&
+				    mmcm_ptr->clkout2_div <= 128) {
+					valid = (true);
+				} else {
+					/* 4 pixels per clock */
+					if (ppc == (XVIDC_PPC_4)) {
+						/* Decrease mult value */
+						mult -= 4;
+					} else if (ppc == (XVIDC_PPC_2)) {
+					/* 2 pixels per clock */
+						/* Decrease M value */
+						mult -= 2;
+					} else {
+						/* 1 pixel per clock */
+						/* Decrease M value */
+						mult -= 1;
+					}
+				}
+			} else {
+				if (mmcm_ptr->clkout0_div > 0 &&
+				    mmcm_ptr->clkout0_div <= 511 &&
+				    mmcm_ptr->clkout1_div > 0 &&
+				    mmcm_ptr->clkout1_div <= 511 &&
+				    mmcm_ptr->clkout2_div > 0 &&
+				    mmcm_ptr->clkout2_div <= 511) {
+					valid = (true);
+				} else { /* 4 pixels per clock */
+					if (ppc == (XVIDC_PPC_4)) {
+						/* Decrease mult value */
+						mult -= 4;
+					} else if (ppc == (XVIDC_PPC_2)) {
+						/* 2 pixels per clock */
+						/* Decrease M value */
+						mult -= 2;
+					} else {
+						/* 1 pixel per clock */
+						/* Decrease M value */
+						mult -= 1;
+					}
+				}
+			}
+		} while (!valid && (mult > 0) && (mult < 129));
+
+		/* Increment divider */
+		div++;
+	} while (!valid && (div > 0) && (div < 107));
+
+	if (valid)
+		return 0;
+
+	dev_err(inst->dev, "failed to caliculate mmmcm params\n");
+
+	return 1;
+}
+
+/**
+ * xhdmiphy_clk_cal_params - This function will try to find the necessary PLL
+ * divisor values to produce the configured line rate given the specified PLL
+ * input frequency. This will be done for all channels specified by chid.
+ * This function is a wrapper for xhdmiphy_pll_cal.
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance.
+ * @chid:		chid is the channel ID to calculate the PLL values for.
+ * @dir:		dir is an indicator for TX or RX.
+ * @pll_in_freq:	pll_clkin_freq is the PLL input frequency on which to
+ *			base the calculations on. A value of 0 indicates to use
+ *			the currently configured quad PLL reference clock.
+ *			A non-zero value indicates to ignore what is currently
+ *			configured in SW, and use a custom frequency instead.
+ *
+ * @return:		- 0 if valid PLL values were found to satisfy the
+ *			constraints
+ *			- 1 otherwise
+ */
+static u32 xhdmiphy_clk_cal_params(struct xhdmiphy_dev *inst, enum chid chid,
+				   enum dir dir, u32 pll_in_freq)
+{
+	u32 status = 0;
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+
+	for (id = id0; id <= id1; id++) {
+		status = xhdmiphy_pll_cal(inst, (enum chid)id, dir,
+					  pll_in_freq);
+		if (status != 0)
+			return status;
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_qpll_param - This function calculates the qpll parameters.
+ *
+ * @inst:	inst is a pointer to the HDMI GT core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:
+ *		- 0 if calculated QPLL parameters updated
+ *			successfully
+ *		- 1 if parameters not updated
+ */
+u32 xhdmiphy_qpll_param(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir)
+{
+	enum sysclk_data_sel sysclk_data_sel = 0;
+	enum chid act_cmnid = XHDMIPHY_CHID_CMN0;
+	enum sysclk_outsel sysclk_out_sel = 0;
+	u64 refclk = 0, tx_linerate = 0;
+	u32 *refclk_ptr;
+	u32 qpll_clkmin = 0;
+	u32 status, qpll_refclk;
+	u8 sr_arr[] = {1, 3, 5};
+	u8 sr_index, sr_val, id, id0, id1;
+
+	/* determine qpll reference clock from the first (master) channel */
+	if (dir == XHDMIPHY_DIR_RX) {
+		qpll_refclk = inst->rx_refclk_hz;
+		refclk_ptr = &inst->rx_refclk_hz;
+	} else {
+		qpll_refclk = inst->tx_refclk_hz;
+		refclk_ptr = &inst->tx_refclk_hz;
+	}
+
+	if (inst->conf.gt_type == XHDMIPHY_GTHE4) {
+		/* determine which QPLL to use */
+		if ((qpll_refclk >= 102343750 && qpll_refclk <= 122500000) ||
+		    (qpll_refclk >= 204687500 && qpll_refclk <= 245000000) ||
+		    (qpll_refclk >= 409375000 && qpll_refclk <= 490000000)) {
+			sysclk_data_sel = XHDMIPHY_SYSCLKSELDATA_QPLL1_OUTCLK;
+			sysclk_out_sel = XHDMIPHY_SYSCLKSELOUT_QPLL1_REFCLK;
+			act_cmnid = XHDMIPHY_CHID_CMN1;
+			qpll_clkmin = (u32)XHDMIPHY_HDMI_GTHE4_QPLL1_REFCLK_MIN;
+		} else {
+			sysclk_data_sel = XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK;
+			sysclk_out_sel = XHDMIPHY_SYSCLKSELOUT_QPLL0_REFCLK;
+			act_cmnid = XHDMIPHY_CHID_CMN0;
+			qpll_clkmin = (u32)XHDMIPHY_HDMI_GTHE4_QPLL0_REFCLK_MIN;
+		}
+	} else if (inst->conf.gt_type == XHDMIPHY_GTYE4) {
+		if ((qpll_refclk >= 102343750 && qpll_refclk <= 122500000) ||
+		    (qpll_refclk >= 204687500 && qpll_refclk <= 245000000) ||
+		    (qpll_refclk >= 409375000 && qpll_refclk <= 490000000)) {
+			sysclk_data_sel = XHDMIPHY_SYSCLKSELDATA_QPLL1_OUTCLK;
+			sysclk_out_sel = XHDMIPHY_SYSCLKSELOUT_QPLL1_REFCLK;
+			act_cmnid = XHDMIPHY_CHID_CMN1;
+			qpll_clkmin = (u32)XHDMIPHY_HDMI_GTYE4_QPLL1_REFCLK_MIN;
+		} else {
+			sysclk_data_sel = XHDMIPHY_SYSCLKSELDATA_QPLL0_OUTCLK;
+			sysclk_out_sel = XHDMIPHY_SYSCLKSELOUT_QPLL0_REFCLK;
+			act_cmnid = XHDMIPHY_CHID_CMN0;
+			qpll_clkmin = (u32)XHDMIPHY_HDMI_GTYE4_QPLL0_REFCLK_MIN;
+		}
+	}
+
+	/* update qpll clock selections */
+	xhdmiphy_sysclk_data_sel(inst, dir, sysclk_data_sel);
+	xhdmiphy_sysclk_out_sel(inst, dir, sysclk_out_sel);
+
+	/* rx is using qpll */
+	if (dir == XHDMIPHY_DIR_RX) {
+		/*
+		 * check if the reference clock is not below the minimum qpll
+		 * input frequency
+		 */
+		if (qpll_refclk >= qpll_clkmin) {
+			refclk = qpll_refclk;
+			/* Scaled line rate */
+			if (inst->rx_hdmi21_cfg.is_en == 0) {
+				if (inst->rx_tmdsclock_ratio)
+					xhdmiphy_cfg_linerate(inst,
+							      XHDMIPHY_CHID_CMNA,
+							      (refclk * 40));
+				else
+					xhdmiphy_cfg_linerate(inst,
+							      XHDMIPHY_CHID_CMNA,
+							      (refclk * 10));
+			} else {
+				xhdmiphy_cfg_linerate(inst,
+						      XHDMIPHY_CHID_CMNA,
+						      inst->rx_hdmi21_cfg.linerate);
+			}
+			/* clear DRU is enabled flag */
+			inst->rx_dru_enabled = 0;
+
+			/* Set RX data width */
+			xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+			for (id = id0; id <= id1; id++) {
+				if (inst->conf.transceiver_width == 2) {
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 20;
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 2;
+				} else {
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 40;
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 4;
+				}
+			}
+		} else if (inst->conf.dru_present) {
+			refclk = xhdmiphy_get_dru_refclk(inst);
+			/* check DRU frequency */
+			if (refclk == 1) {
+				dev_err(inst->dev, "cannot get dru refclk\n");
+				return 1;
+			}
+
+			/* round input frequency to 10 kHz */
+			refclk = (refclk + 5000) / 10000;
+			refclk = refclk * 10000;
+
+			/* wet the DRU to operate at a linerate of 2.5 Gbps */
+			xhdmiphy_cfg_linerate(inst, XHDMIPHY_CHID_CMNA,
+					      (get_gthdmi_ptr(inst))->dru_linerate);
+
+			/* set DRU is enabled flag */
+			inst->rx_dru_enabled = 1;
+
+			/* set RX data width to 40 and 4 bytes */
+			xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+			for (id = id0; id <= id1; id++) {
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 20;
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 2;
+			}
+		} else {
+			dev_err(inst->dev, "dru is not present\n");
+			return 1;
+		}
+	/* TX is using QPLL */
+	} else {
+		/* Set default TX sample rate */
+		inst->tx_samplerate = 1;
+
+		if (inst->tx_hdmi21_cfg.is_en == 0) {
+			/* Update TX line rates */
+			xhdmiphy_cfg_linerate(inst, XHDMIPHY_CHID_CMNA,
+					      ((u64)(*refclk_ptr) * 10));
+			tx_linerate = (*refclk_ptr) / 100000;
+
+			/* Check if the linerate is above the 340 Mcsc */
+			if ((tx_linerate) >= XHDMIPHY_LRATE_3400)
+				(*refclk_ptr) = (*refclk_ptr) / 4;
+		} else { /* inst->tx_hdmi21_cfg.is_en == 1 */
+			xhdmiphy_cfg_linerate(inst, XHDMIPHY_CHID_CMNA,
+					      inst->tx_hdmi21_cfg.linerate);
+		}
+	}
+
+	/* Calculate QPLL values */
+	for (sr_index = 0; sr_index < sizeof(sr_arr); sr_index++) {
+		/* Only use oversampling when then TX is using the QPLL */
+		if (dir == XHDMIPHY_DIR_TX) {
+			sr_val = sr_arr[sr_index];
+
+			if (inst->tx_hdmi21_cfg.is_en == 0) {
+				/*
+				 * TX reference clock is below the minimum QPLL
+				 * clock input frequency
+				 */
+				if ((*refclk_ptr) < qpll_clkmin) {
+					refclk = ((*refclk_ptr) * sr_val);
+
+					/* Calculate scaled line rate */
+					if (tx_linerate >= XHDMIPHY_LRATE_3400) {
+						xhdmiphy_cfg_linerate(inst,
+								      XHDMIPHY_CHID_CMNA,
+								      (u64)(refclk * 40));
+					} else {
+						xhdmiphy_cfg_linerate(inst,
+								      XHDMIPHY_CHID_CMNA,
+								      (u64)(refclk * 10));
+					}
+				} else {
+					/*
+					 * TX reference clock is in QPLL clock input range.
+					 * In this case don't increase the reference clock, but
+					 * increase the line rate.
+					 */
+					refclk = (*refclk_ptr);
+
+					/* Calculate scaled line rate */
+					if (tx_linerate >= XHDMIPHY_LRATE_3400) {
+						xhdmiphy_cfg_linerate(inst,
+								      XHDMIPHY_CHID_CMNA,
+								      (u64)(refclk * 40 * sr_val));
+					} else {
+						xhdmiphy_cfg_linerate(inst,
+								      XHDMIPHY_CHID_CMNA,
+								      (u64)(refclk * 10 * sr_val));
+					}
+				}
+			} else { /* inst->tx_hdmi21_cfg.is_en == 1 */
+				refclk = (*refclk_ptr);
+			}
+		} else {
+			/* For all other reference clocks force sample rate to one */
+			sr_val = 1;
+		}
+
+		status = xhdmiphy_clk_cal_params(inst, act_cmnid, dir, refclk);
+		if (status == 0) {
+			/* Only execute when the TX is using the QPLL */
+			if (dir == XHDMIPHY_DIR_TX) {
+				/* Set TX sample rate */
+				inst->tx_samplerate = sr_val;
+
+				/*
+				 * Update reference clock only when the
+				 * reference clock is below the minimum QPLL
+				 * input frequency.
+				 */
+				if ((*refclk_ptr) < qpll_clkmin) {
+					(*refclk_ptr) = (*refclk_ptr) * sr_val;
+				} else if (sr_val > 1) {
+					dev_err(inst->dev,
+						"failed to configure qpll params\n");
+					return 1;
+				}
+			}
+			/*
+			 * Check Userclock Frequency (300 MHz + 0.5%) + 10 KHz
+			 * (Clkdet accuracy)
+			 */
+			if (301500000 < (xhdmiphy_get_linerate(inst, act_cmnid) /
+					 (inst->conf.transceiver_width * 10))) {
+				dev_err(inst->dev, "user clock error\n");
+				return 1;
+			}
+
+			return 0;
+		}
+	}
+
+	dev_err(inst->dev, "failed to configure qpll params\n");
+	return 1;
+}
+
+/**
+ * xhdmiphy_cpll_param - This function calculates the CPLL parameters.
+ *
+ * @inst:	inst is a pointer to the HDMI GT core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:	- 0 if calculated CPLL parameters updated
+ *		  successfully
+ *		- 1 if parameters not updated
+ */
+u32 xhdmiphy_cpll_param(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir)
+{
+	enum chid ch_id = XHDMIPHY_CHID_CHA;
+	u64 refclk = 0;
+	u32 *refclk_ptr;
+	u32 tx_linerate = 0;
+	u32 status;
+	u8 sr_arr[] = {1, 3, 5};
+	u8 sr_index, sr_val, id, id0, id1;
+
+	/* tx is using cpll */
+	if (dir == XHDMIPHY_DIR_TX) {
+		/* set default tx sample rate */
+		inst->tx_samplerate = 1;
+		refclk_ptr = &inst->tx_refclk_hz;
+		if (inst->tx_hdmi21_cfg.is_en == 0) {
+			xhdmiphy_cfg_linerate(inst, ch_id,
+					      (u64)((*refclk_ptr) * 10));
+			tx_linerate = (*refclk_ptr)  / 100000;
+			/* check if the line rate is above the 340 Mcsc */
+			if (tx_linerate >= XHDMIPHY_LRATE_3400)
+				(*refclk_ptr) = (*refclk_ptr) / 4;
+		} else {
+			xhdmiphy_cfg_linerate(inst, ch_id,
+					      (u64)(inst->tx_hdmi21_cfg.linerate));
+			tx_linerate = inst->tx_hdmi21_cfg.linerate / 100000;
+		}
+	} else {
+		/* rx is using cpll */
+		refclk_ptr = &inst->rx_refclk_hz;
+		/*
+		 * check if the reference clock is not below the minimum CPLL
+		 * input frequency
+		 */
+		if ((*refclk_ptr) >= (get_gthdmi_ptr(inst))->cpll_refclk_min) {
+			refclk = (*refclk_ptr);
+			/* scaled linerate */
+			if (inst->rx_hdmi21_cfg.is_en == 0) {
+				if (inst->rx_tmdsclock_ratio) {
+					xhdmiphy_cfg_linerate(inst, ch_id,
+							      (refclk * 40));
+				} else {
+					xhdmiphy_cfg_linerate(inst, ch_id,
+							      (refclk * 10));
+				}
+			} else { /* inst->rx_hdmi21_cfg.is_en == 1 */
+				xhdmiphy_cfg_linerate(inst, ch_id,
+						      inst->rx_hdmi21_cfg.linerate);
+			}
+
+			inst->rx_dru_enabled = 0;
+			xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0,
+					&id1);
+			for (id = id0; id <= id1; id++) {
+				if (inst->conf.transceiver_width == 2) {
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 20;
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 2;
+				} else {
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 40;
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 4;
+				}
+			}
+		} else {
+			if (inst->conf.dru_present) {
+				/* Return config not found error when TMDS ratio is 1/40 */
+				if (inst->rx_tmdsclock_ratio) {
+					dev_err(inst->dev, "cpll config not found\n");
+					return 1;
+				}
+				refclk = xhdmiphy_get_dru_refclk(inst);
+				/* check DRU frequency */
+				if (refclk == 1) {
+					dev_err(inst->dev,
+						"cannot get dru refclk\n");
+					return 1;
+				}
+
+				/* Round input frequency to 10 kHz */
+				refclk = (refclk + 5000) / 10000;
+				refclk = refclk * 10000;
+
+				/*
+				 * set the dru to operate at a linerate of
+				 * 2.5 Gbps
+				 */
+				xhdmiphy_cfg_linerate(inst, ch_id,
+						      (get_gthdmi_ptr(inst))->
+						      dru_linerate);
+				/* Set dru is enabled flag */
+				inst->rx_dru_enabled = 1;
+
+				/* set rx data width */
+				xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA,
+						&id0, &id1);
+				for (id = id0; id <= id1; id++) {
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 20;
+					inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 2;
+				}
+
+				if (tx_linerate > (((get_gthdmi_ptr(inst))->
+						dru_linerate) / 1000000)) {
+					dev_err(inst->dev,
+						"video format is not supported\n");
+					return 1;
+				}
+			} else {
+				/* return config not found error when TMDS ratio is 1/40 */
+				if (inst->rx_tmdsclock_ratio) {
+					dev_err(inst->dev,
+						"cpll config not found\n");
+				} else {
+					dev_err(inst->dev, "no dru present\n");
+				}
+				return 1;
+			}
+		}
+	}
+
+	/* try different sample rates */
+	for (sr_index = 0; sr_index < sizeof(sr_arr); sr_index++) {
+		/* only use oversampling when then tx is using the cpll */
+		if (dir == XHDMIPHY_DIR_TX) {
+			sr_val = sr_arr[sr_index];
+			if (inst->tx_hdmi21_cfg.is_en == 0) {
+				/* multiply the reference clock with the sample
+				 * rate value
+				 */
+				refclk = ((*refclk_ptr) * sr_val);
+				/* calculate scaled line rate */
+				if (tx_linerate >= XHDMIPHY_LRATE_3400) {
+					xhdmiphy_cfg_linerate(inst, ch_id,
+							      (refclk * 40));
+				} else {
+					xhdmiphy_cfg_linerate(inst,
+							      ch_id,
+							      (refclk * 10));
+				}
+			} else { /* inst->tx_hdmi21_cfg.is_en == 1 */
+				refclk = (*refclk_ptr);
+			}
+		/* for all other reference clocks force sample rate to one */
+		} else {
+			sr_val = 1;
+		}
+
+		status = xhdmiphy_clk_cal_params(inst, ch_id, dir, refclk);
+		if (status == (0)) {
+			/* only execute when the tx is using the qpll */
+			if (dir == XHDMIPHY_DIR_TX) {
+				inst->tx_samplerate = sr_val;
+				(*refclk_ptr) = (*refclk_ptr) * sr_val;
+			}
+
+			/* check userclock frequency */
+			/* (300 MHz + 0.5%) + 10 KHz (clkdet accuracy) */
+			if (301500000 <
+			    (xhdmiphy_get_linerate(inst,
+						   XHDMIPHY_CHID_CH1) /
+						   (inst->conf.transceiver_width * 10))) {
+				dev_err(inst->dev, "user clock error\n");
+				return 1;
+			}
+
+			return 0;
+		}
+	}
+
+	dev_err(inst->dev, "cpll config not found\n");
+
+	return 1;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xhdmiphy_modules.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xhdmiphy_modules.c
@@ -0,0 +1,2004 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/device.h>
+#include "xhdmiphy.h"
+
+void xhdmiphy_intr_en(struct xhdmiphy_dev *inst, u32 intr)
+{
+	u32 reg_val;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_INTR_EN_REG);
+	reg_val |= intr;
+	xhdmiphy_write(inst, XHDMIPHY_INTR_EN_REG, reg_val);
+}
+
+void xhdmiphy_intr_dis(struct xhdmiphy_dev *inst, u32 intr)
+{
+	u32 reg_val;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_INTR_DIS_REG);
+	reg_val |= intr;
+	xhdmiphy_write(inst, XHDMIPHY_INTR_DIS_REG, reg_val);
+}
+
+static void xhdmiphy_set(struct xhdmiphy_dev *inst, u32 addr, u32 set)
+{
+	xhdmiphy_write(inst, addr, xhdmiphy_read(inst, addr) | set);
+}
+
+inline void xhdmiphy_clr(struct xhdmiphy_dev *inst, u32 addr, u32 clr)
+{
+	xhdmiphy_write(inst, addr, xhdmiphy_read(inst, addr) & ~clr);
+}
+
+/**
+ * xhdmiphy_outdiv_reconf - This function will set the current output divider
+ * configuration over DRP.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID for which to write the settings for
+ * @dir:	dir is an indicator for RX or TX
+ */
+static void xhdmiphy_outdiv_reconf(struct xhdmiphy_dev *inst, enum chid chid,
+				   enum dir dir)
+{
+	u32 ret = 0;
+	u8 id, id0, id1;
+
+	if (!xhdmiphy_is_ch(chid))
+		chid = XHDMIPHY_CHID_CHA;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+
+	for (id = id0; id <= id1; id++) {
+		ret = xhdmiphy_outdiv_ch_reconf(inst, (enum chid)id, dir);
+		if (ret != 0)
+			break;
+	}
+}
+
+/**
+ * xhdmiphy_clkdet_freq_reset - This function will reset the clock change detector module.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for RX or TX
+ */
+void xhdmiphy_clkdet_freq_reset(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	u32 regval;
+
+	regval = xhdmiphy_read(inst, XHDMIPHY_CLKDET_CTRL_REG);
+	if (dir == XHDMIPHY_DIR_TX)
+		regval |= XHDMIPHY_CLKDET_CTRL_TX_FREQ_RST_MASK;
+	else
+		regval |= XHDMIPHY_CLKDET_CTRL_RX_FREQ_RST_MASK;
+
+	xhdmiphy_write(inst, XHDMIPHY_CLKDET_CTRL_REG, regval);
+}
+
+/**
+ * xhdmiphy_clkdet_freq_threshold - This function sets the clock detector
+ * frequency lock counter threshold value.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @thres_val:	thresholdVal is the threshold value to be set
+ */
+static void xhdmiphy_clkdet_freq_threshold(struct xhdmiphy_dev *inst,
+					   u16 thres_val)
+{
+	u32 reg_val;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_CLKDET_CTRL_REG);
+
+	reg_val &= ~XHDMIPHY_CLKDET_CTRL_RX_FREQ_RST_MASK;
+	reg_val |= (thres_val << XHDMIPHY_CLKDET_CTRL_FREQ_LOCK_THRESH_SHIFT);
+	xhdmiphy_write(inst, XHDMIPHY_CLKDET_CTRL_REG, reg_val);
+}
+
+/**
+ * xhdmiphy_patgen_set_ratio - This function sets the Pattern Generator for the
+ * GT channel 4 when it is used to generate the TX TMDS Clock.
+ *
+ * @inst:		inst is a pointer to the xhdmiphy core instance
+ * @tx_linerate:	tx_linerate in Mbps
+ */
+static void xhdmiphy_patgen_set_ratio(struct xhdmiphy_dev *inst,
+				      u64 tx_linerate)
+{
+	u32 reg_val;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_PATGEN_CTRL_REG)
+				 & ~XHDMIPHY_PATGEN_CTRL_RATIO_MASK;
+
+	if (tx_linerate >= XHDMIPHY_LRATE_3400 && inst->tx_samplerate == 1)
+		reg_val |= XHDMIPHY_patgen_ratio_40 &
+			   XHDMIPHY_PATGEN_CTRL_RATIO_MASK;
+	else
+		reg_val |= inst->tx_samplerate &
+			   XHDMIPHY_PATGEN_CTRL_RATIO_MASK;
+
+	xhdmiphy_write(inst, XHDMIPHY_PATGEN_CTRL_REG, reg_val);
+}
+
+static void xhdmiphy_dru_reset(struct xhdmiphy_dev *inst, enum chid chid,
+			       u8 rst)
+{
+	u32 reg_val, mask_val = 0;
+	u8 id, id0, id1;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_DRU_CTRL_REG);
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+
+	for (id = id0; id <= id1; id++)
+		mask_val |= XHDMIPHY_DRU_CTRL_RST_MASK(id);
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_DRU_CTRL_REG, reg_val, mask_val, rst);
+}
+
+static void xhdmiphy_dru_en(struct xhdmiphy_dev *inst, enum chid chid, u8 en)
+{
+	u32 reg_val, mask_val = 0;
+	u8 id, id0, id1;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_DRU_CTRL_REG);
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+
+	for (id = id0; id <= id1; id++)
+		mask_val |= XHDMIPHY_DRU_CTRL_EN_MASK(id);
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_DRU_CTRL_REG, reg_val, mask_val, en);
+}
+
+static void xhdmiphy_dru_mode_en(struct xhdmiphy_dev *inst, u8 en)
+{
+	u32 reg_val, reg_mask = 0;
+	u8 id, id0, id1;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_RX_EQ_CDR_REG);
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		reg_mask |= XHDMIPHY_RX_STATUS_RXCDRHOLD_MASK(id) |
+			    XHDMIPHY_RX_STATUS_RXOSOVRDEN_MASK(id) |
+			    XHDMIPHY_RX_STATUS_RXLPMLFKLOVRDEN_MASK(id) |
+			    XHDMIPHY_RX_STATUS_RXLPMHFOVRDEN_MASK(id);
+	}
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_RX_EQ_CDR_REG, reg_val, reg_mask, en);
+}
+
+static void xhdmiphy_set_dru_centerfreq(struct xhdmiphy_dev *inst,
+					enum chid chid, u64 center_freq)
+{
+	u32 center_freq_l, center_freq_h, reg_off;
+	u8 id, id0, id1;
+
+	/* Split the 64-bit input into 2 32-bit values */
+	center_freq_l = lower_32_bits(center_freq);
+	center_freq_h = upper_32_bits(center_freq);
+
+	center_freq_h &= XHDMIPHY_DRU_CFREQ_H_MASK;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		reg_off = XHDMIPHY_DRU_CFREQ_L_REG(id);
+		xhdmiphy_write(inst, reg_off, center_freq_l);
+
+		reg_off = XHDMIPHY_DRU_CFREQ_H_REG(id);
+		xhdmiphy_write(inst, reg_off, center_freq_h);
+	}
+}
+
+/**
+ * xhdmiphy_get_dru_refclk - This function returns the frequency of the DRU
+ * reference clock as measured by the clock detector peripheral.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ *
+ * @return:	The measured frequency of the DRU reference clock
+ */
+u32 xhdmiphy_get_dru_refclk(struct xhdmiphy_dev *inst)
+{
+	u32 dru_freq = xhdmiphy_read(inst, XHDMIPHY_CLKDET_FREQ_DRU_REG);
+
+	if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTHE4) {
+		if (dru_freq > XHDMIPHY_HDMI_GTHE4_DRU_REFCLK_MIN &&
+		    dru_freq < XHDMIPHY_HDMI_GTHE4_DRU_REFCLK_MAX) {
+			return XHDMIPHY_HDMI_GTHE4_DRU_REFCLK;
+		} else if (dru_freq > XHDMIPHY_HDMI_GTHE4_DRU_REFCLK2_MIN &&
+			   dru_freq < XHDMIPHY_HDMI_GTHE4_DRU_REFCLK2_MAX) {
+			return XHDMIPHY_HDMI_GTHE4_DRU_REFCLK2;
+		}
+	} else if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTYE4) {
+		if (dru_freq > XHDMIPHY_HDMI_GTYE4_DRU_REFCLK_MIN &&
+		    dru_freq < XHDMIPHY_HDMI_GTYE4_DRU_REFCLK_MAX) {
+			return XHDMIPHY_HDMI_GTYE4_DRU_REFCLK;
+		} else if (dru_freq > XHDMIPHY_HDMI_GTYE4_DRU_REFCLK2_MIN &&
+			   dru_freq < XHDMIPHY_HDMI_GTYE4_DRU_REFCLK2_MAX) {
+			return XHDMIPHY_HDMI_GTYE4_DRU_REFCLK2;
+		}
+	} else {
+		if (dru_freq > XHDMIPHY_HDMI_GTYE5_DRU_REFCLK_MIN &&
+		    dru_freq < XHDMIPHY_HDMI_GTYE5_DRU_REFCLK_MAX) {
+			return XHDMIPHY_HDMI_GTYE5_DRU_REFCLK;
+		}
+		if (dru_freq > XHDMIPHY_HDMI_GTYE5_DRU_REFCLK1_MIN &&
+		    dru_freq < XHDMIPHY_HDMI_GTYE5_DRU_REFCLK1_MAX) {
+			return XHDMIPHY_HDMI_GTYE5_DRU_REFCLK1;
+		}
+		if (dru_freq > XHDMIPHY_HDMI_GTYE5_DRU_REFCLK2_MIN &&
+		    dru_freq < XHDMIPHY_HDMI_GTYE5_DRU_REFCLK2_MAX) {
+			return XHDMIPHY_HDMI_GTYE5_DRU_REFCLK2;
+		}
+	}
+
+	return 1;
+}
+
+/**
+ * xhdmiphy_dru_cal_centerfreq - This function calculates the center frequency
+ * value for the DRU.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy GT core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	The calculated DRU Center frequency value.
+ *		According to XAPP1240 Center_f = fDIN * (2^32)/fdruclk
+ *		The DRU clock is derived from the measured reference clock and
+ *		the current QPLL settings.
+ */
+static u64 xhdmiphy_dru_cal_centerfreq(struct xhdmiphy_dev *inst,
+				       enum chid chid)
+{
+	struct channel *ch_ptr;
+	struct pll_param *pll_prm;
+	u64 dru_refclk, clkdet_refclk, data_rate, f_din, fdru_clk;
+
+	clkdet_refclk = xhdmiphy_read(inst, XHDMIPHY_CLKDET_FREQ_RX_REG);
+	pll_prm = &inst->quad.plls[XHDMIPHY_CH2IDX(chid)].pll_param;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		dru_refclk = xhdmiphy_get_dru_refclk(inst);
+		/* take the master channel (channel 1) */
+		ch_ptr = &inst->quad.ch1;
+		if (chid == XHDMIPHY_CHID_CMN0 || chid == XHDMIPHY_CHID_CMN1) {
+			fdru_clk = (dru_refclk * pll_prm->nfb_div) /
+				    (pll_prm->m_refclk_div *
+				     (ch_ptr->rx_outdiv * 20));
+		} else {
+			fdru_clk = (dru_refclk * ch_ptr->pll_param.n1fb_div *
+				    ch_ptr->pll_param.n2fb_div * 2) /
+				    (ch_ptr->pll_param.m_refclk_div *
+				    ch_ptr->rx_outdiv * 20);
+		}
+	} else {
+		fdru_clk = (u64)(XHDMIPHY_HDMI_GTYE5_DRU_LRATE / 20);
+	}
+
+	data_rate = 10 * clkdet_refclk;
+	f_din = data_rate * ((u64)1 << 32);
+
+	if (f_din && fdru_clk)
+		return (f_din / fdru_clk);
+
+	return 0;
+}
+
+/**
+ * xhdmiphy_dir_reconf - This function will set the current RX/TX configuration
+ * over DRP.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID for which to write the settings for
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static bool xhdmiphy_dir_reconf(struct xhdmiphy_dev *inst, enum chid chid, enum dir dir)
+{
+	u32 status = 0;
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		if (dir == XHDMIPHY_DIR_TX)
+			status |= xhdmiphy_txch_reconf(inst, id);
+		else
+			status |= xhdmiphy_rxch_reconf(inst, id);
+
+		if (status != 0)
+			return true;
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_clk_reconf - This function will set the current clocking settings
+ * for each channel to hardware based on the configuration stored in the
+ * driver's instance. hardware based on the configuration stored in the driver's
+ * instance.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID for which to write the settings for
+ *
+ * @return:	- 0 if the configuration was successful
+ *		- 1 otherwise
+ */
+static bool xhdmiphy_clk_reconf(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	u32 status = 0;
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		if (xhdmiphy_is_ch(id)) {
+			status |= xhdmiphy_clk_ch_reconf(inst, (enum chid)id);
+		} else if (xhdmiphy_is_cmn(chid)) {
+			if (((xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX)) ||
+			     (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX))) &&
+			     inst->qpll_present == 0) {
+				dev_err(inst->dev,
+					"return failure: qpll is not present\n");
+				return false;
+			}
+			status |= xhdmiphy_clk_cmn_reconf(inst, (enum chid)id);
+		}
+		if (status)
+			return false;
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_get_rcfg_chid - obtain the reconfiguration channel ID for given
+ * PLL type
+ *
+ * @pll_type:	pll_type is the PLL type being used by the channel
+ *
+ * @return:	The Channel ID to be used for reconfiguration
+ */
+static u8 xhdmiphy_get_rcfg_chid(enum pll_type pll_type)
+{
+	enum chid chid;
+
+	switch (pll_type) {
+	case XHDMIPHY_PLL_QPLL:
+	case XHDMIPHY_PLL_QPLL0:
+	case XHDMIPHY_PLL_LCPLL:
+		chid = XHDMIPHY_CHID_CMN0;
+		break;
+	case XHDMIPHY_PLL_QPLL1:
+	case XHDMIPHY_PLL_RPLL:
+		chid = XHDMIPHY_CHID_CMN1;
+		break;
+	default:
+		chid = XHDMIPHY_CHID_CHA;
+		break;
+	}
+
+	return chid;
+}
+
+/*
+ * This function sets the system clock selection
+ *
+ * @inst:	inst is a pointer to the xhmdiphy core instance
+ *
+ * @return:	none
+ */
+static void xhdmiphy_set_sys_clksel(struct xhdmiphy_dev *inst)
+{
+	if (inst->conf.tx_pllclk_sel == inst->conf.rx_pllclk_sel) {
+		if (inst->conf.rx_pllclk_sel ==
+		    XHDMIPHY_SYSCLKSELDATA_CPLL_OUTCLK)
+			xhdmiphy_pll_init(inst, XHDMIPHY_CHID_CHA,
+					  inst->conf.rx_refclk_sel,
+					  inst->conf.rx_refclk_sel,
+					  XHDMIPHY_PLL_CPLL,
+					  XHDMIPHY_PLL_CPLL);
+		else
+			xhdmiphy_pll_init(inst, XHDMIPHY_CHID_CMN0,
+					  inst->conf.rx_refclk_sel,
+					  inst->conf.rx_refclk_sel,
+					  XHDMIPHY_PLL_QPLL0,
+					  XHDMIPHY_PLL_QPLL0);
+	} else if (inst->conf.tx_pllclk_sel ==
+					XHDMIPHY_SYSCLKSELDATA_CPLL_OUTCLK) {
+		xhdmiphy_pll_init(inst, XHDMIPHY_CHID_CHA,
+				  inst->conf.rx_refclk_sel,
+				  inst->conf.tx_refclk_sel,
+				  XHDMIPHY_PLL_CPLL,
+				  XHDMIPHY_PLL_QPLL0);
+	} else {
+		xhdmiphy_pll_init(inst, XHDMIPHY_CHID_CMN0,
+				  inst->conf.tx_refclk_sel,
+				  inst->conf.rx_refclk_sel,
+				  XHDMIPHY_PLL_QPLL0,
+				  XHDMIPHY_PLL_CPLL);
+	}
+}
+
+/**
+ * xhdmiphy_mmcm_clkin_sel - This function will set the CLKINSEL port
+ * of theMMCM
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @dir:	dir is an indicator for TX or RX
+ * @sel:	sel CLKINSEL value
+ *		0 - CLKIN1
+ *		1 - CLKIN2
+ */
+static void xhdmiphy_mmcm_clkin_sel(struct xhdmiphy_dev *inst, enum dir dir,
+				    enum mmcmclk_insel sel)
+{
+	u32 reg_off, reg_val;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_MMCM_TXUSRCLK_CTRL_REG;
+	else
+		reg_off = XHDMIPHY_MMCM_RXUSRCLK_CTRL_REG;
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+
+	if (sel == XHDMIPHY_MMCM_CLKINSEL_CLKIN2)
+		reg_val &= ~XHDMIPHY_MMCM_USRCLK_CTRL_CLKINSEL_MASK;
+	else
+		reg_val |= XHDMIPHY_MMCM_USRCLK_CTRL_CLKINSEL_MASK;
+
+	xhdmiphy_write(inst, reg_off, reg_val);
+}
+
+/**
+ * xhdmiphy_reset_gtpll - This function will reset the GT's PLL logic.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID which to operate on
+ * @dir:	dir is an indicator for TX or RX
+ * @hold:	hold is an indicator whether to "hold" the reset if set to 1.
+ *		If set to 0: reset, then enable.
+ */
+static void xhdmiphy_reset_gtpll(struct xhdmiphy_dev *inst, enum chid chid,
+				 enum dir dir, u8 hold)
+{
+	u32 reg_val, mask_val, reg_off;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_TX_INIT_REG;
+	else
+		reg_off = XHDMIPHY_RX_INIT_REG;
+
+	if (chid == XHDMIPHY_CHID_CHA)
+		mask_val = XHDMIPHY_TXRX_INIT_PLLGTRESET_ALL_MASK;
+	else
+		mask_val = XHDMIPHY_TXRX_INIT_PLLGTRESET_MASK(chid);
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val |= mask_val;
+	xhdmiphy_write(inst, reg_off, reg_val);
+
+	if (!hold) {
+		reg_val &= ~mask_val;
+		xhdmiphy_write(inst, reg_off, reg_val);
+	}
+}
+
+u32 xhdmiphy_init_phy(struct xhdmiphy_dev *inst)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_cfg_init(inst);
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+			XHDMIPHY_GT_STATE_IDLE;
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+			XHDMIPHY_GT_STATE_IDLE;
+		if (inst->conf.transceiver_width == 2) {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_data_width = 20;
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_intdata_width = 2;
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 20;
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 2;
+		} else {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_data_width = 40;
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_intdata_width = 4;
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_data_width = 40;
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_intdata_width = 4;
+		}
+	}
+	xhdmiphy_clr(inst, XHDMIPHY_CLKDET_CTRL_REG,
+		     XHDMIPHY_CLKDET_CTRL_RUN_MASK);
+
+	/* sets clock detector frequency lock counter threshold value */
+	xhdmiphy_write(inst, XHDMIPHY_CLKDET_FREQ_TMR_TO_REG,
+		       inst->conf.axilite_freq);
+	xhdmiphy_clkdet_freq_threshold(inst, 40);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		xhdmiphy_set_sys_clksel(inst);
+
+		/* indicate of QPLL is present in design */
+		if ((xhdmiphy_is_using_qpll(inst, XHDMIPHY_CHID_CH1,
+					    XHDMIPHY_DIR_TX) &&
+		     (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX))) ||
+		    (xhdmiphy_is_using_qpll(inst, XHDMIPHY_CHID_CH1,
+					    XHDMIPHY_DIR_RX) &&
+		     (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX)))) {
+			inst->qpll_present = true;
+		} else {
+			inst->qpll_present = false;
+		}
+
+		if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTHE4 ||
+		    inst->conf.gt_type == XHDMIPHY_GTTYPE_GTYE4) {
+			xhdmiphy_set_bufgtdiv(inst, XHDMIPHY_DIR_TX, 1);
+			xhdmiphy_set_bufgtdiv(inst, XHDMIPHY_DIR_RX, 1);
+		}
+		xhdmiphy_powerdown_gtpll(inst, XHDMIPHY_CHID_CMNA, true);
+		xhdmiphy_powerdown_gtpll(inst, XHDMIPHY_CHID_CHA, true);
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_RX, true);
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_TX, true);
+	}
+
+	xhdmiphy_mmcm_reset(inst, XHDMIPHY_DIR_TX, true);
+	xhdmiphy_mmcm_reset(inst, XHDMIPHY_DIR_RX, true);
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX))
+		xhdmiphy_ibufds_en(inst, XHDMIPHY_DIR_TX, (false));
+
+	if (xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX))
+		xhdmiphy_ibufds_en(inst, XHDMIPHY_DIR_RX, (false));
+
+	/* dru Settings */
+	if (inst->conf.dru_present) {
+		xhdmiphy_ibufds_en(inst, XHDMIPHY_DIR_RX, true);
+		xhdmiphy_dru_reset(inst, XHDMIPHY_CHID_CHA, true);
+		xhdmiphy_dru_en(inst, XHDMIPHY_CHID_CHA, false);
+	}
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+		xhdmiphy_set_rxlpm(inst, XHDMIPHY_CHID_CHA,
+				   XHDMIPHY_DIR_RX, 0);
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+			xhdmiphy_set_tx_vs(inst, (enum chid)id,
+					   XHDMIPHY_HDMI_GTHE4_DEFAULT_VS_VAL);
+		else
+			xhdmiphy_set_tx_vs(inst, (enum chid)id,
+					   XHDMIPHY_HDMI_DEFAULT_VS_VAL);
+
+		xhdmiphy_set_tx_pe(inst, (enum chid)id,
+				   XHDMIPHY_HDMI_DEFAULT_PC_PE_VAL);
+		xhdmiphy_set_tx_pc(inst, (enum chid)id,
+				   XHDMIPHY_HDMI_DEFAULT_PC_PE_VAL);
+	}
+
+	/* clear interrupt register */
+	xhdmiphy_write(inst, XHDMIPHY_INTR_STS_REG, XHDMIPHY_INTR_STS_ALL_MASK);
+
+	/* interrupt enable */
+	xhdmiphy_intr_en(inst, XHDMIPHY_INTR_TXRESETDONE_MASK |
+			 XHDMIPHY_INTR_RXRESETDONE_MASK);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		xhdmiphy_intr_en(inst, XHDMIPHY_INTR_CPLL_LOCK_MASK |
+				 XHDMIPHY_INTR_QPLL_LOCK_MASK |
+				 XHDMIPHY_INTR_TXALIGNDONE_MASK |
+				 XHDMIPHY_INTR_QPLL1_LOCK_MASK);
+	} else {
+		xhdmiphy_intr_en(inst, XHDMIPHY_INTR_LCPLL_LOCK_MASK |
+				 XHDMIPHY_INTR_RPLL_LOCK_MASK |
+				 XHDMIPHY_INTR_TXGPO_RE_MASK |
+				 XHDMIPHY_INTR_RXGPO_RE_MASK);
+	}
+
+	xhdmiphy_intr_en(inst, XHDMIPHY_INTR_TXFREQCHANGE_MASK |
+			 XHDMIPHY_INTR_RXFREQCHANGE_MASK |
+			 XHDMIPHY_INTR_TXMMCMUSRCLK_LOCK_MASK |
+			 XHDMIPHY_INTR_TXTMRTIMEOUT_MASK |
+			 XHDMIPHY_INTR_RXTMRTIMEOUT_MASK |
+			 XHDMIPHY_INTR_RXMMCMUSRCLK_LOCK_MASK);
+
+	xhdmiphy_set(inst, XHDMIPHY_CLKDET_CTRL_REG,
+		     XHDMIPHY_CLKDET_CTRL_RUN_MASK);
+
+	return 0;
+}
+
+/**
+ * xhdmiphy_tx_align_rst - This function resets the GT TX alignment module.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @rst:	rst specifies true/false value to either assert or deassert
+ *		reset on the TX alignment module, respectively
+ */
+static void xhdmiphy_tx_align_rst(struct xhdmiphy_dev *inst, enum chid chid,
+				  u8 rst)
+{
+	u32 reg_val, mask_val = 0;
+	u8 id, id0, id1;
+
+	/* read Tx align register */
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_TX_BUFFER_BYPASS_REG);
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		mask_val |= XHDMIPHY_TX_BUFFER_BYPASS_TXPHDLYRESET_MASK(id);
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_TX_BUFFER_BYPASS_REG, reg_val, mask_val,
+			 rst);
+}
+
+/**
+ * xhdmiphy_tx_align_start - This function resets the GT TX alignment module.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID to operate on
+ * @start:	Start specifies true/false value to either start or ttop the TX
+ *		alignment module, respectively
+ */
+static void xhdmiphy_tx_align_start(struct xhdmiphy_dev *inst, enum chid chid,
+				    u8 start)
+{
+	u32 reg_val,  mask_val = 0;
+	u8 id, id0, id1;
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_TX_BUFFER_BYPASS_REG);
+
+	xhdmiphy_ch2ids(inst, chid, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		mask_val |= XHDMIPHY_TX_BUFFER_BYPASS_TXPHALIGN_MASK(id);
+
+	xhdmiphy_set_clr(inst, XHDMIPHY_TX_BUFFER_BYPASS_REG, reg_val, mask_val,
+			 start);
+}
+
+static void xhdmiphy_txgpo_risingedge_handler(struct xhdmiphy_dev *inst)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_check_linerate_cfg(inst, XHDMIPHY_CHID_CH1, XHDMIPHY_DIR_TX);
+	xhdmiphy_set_gpi(inst, XHDMIPHY_CHID_CHA, XHDMIPHY_DIR_TX, false);
+
+	/* wait for GPO TX = 0 */
+	while (xhdmiphy_get_gpo(inst, XHDMIPHY_CHID_CHA, XHDMIPHY_DIR_TX))
+		;
+
+	xhdmiphy_mmcm_start(inst, XHDMIPHY_DIR_TX);
+
+	xhdmiphy_dir_reconf(inst, XHDMIPHY_CHID_CHA, XHDMIPHY_DIR_TX);
+
+	/* deassert reset on GT Reset IP TX */
+	xhdmiphy_write(inst, XHDMIPHY_COMMON_INIT_REG,
+		       (xhdmiphy_read(inst,
+		       XHDMIPHY_COMMON_INIT_REG) & ~0x1));
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+						XHDMIPHY_GT_STATE_LOCK;
+	}
+}
+
+/**
+ * xhdmiphy_lcpll_param - This function calculates the lcpll parameters.
+ *
+ * @inst:	inst is a pointer to the HDMI GT core instance
+ * @chid:	chid is the channel ID to operate on
+ * @dir:	dir is an indicator for RX or TX
+ *
+ * @return:	- 0 if calculated LCPLL parameters updated successfully
+ *		- 1 if parameters not updated
+ */
+static u32 xhdmiphy_lcpll_param(struct xhdmiphy_dev *inst, enum chid chid,
+				enum dir dir)
+{
+	u64 linerate = 0;
+	u32 status = 0;
+	u32 *refclk_ptr;
+	u8 tmdsclk_ratio = 0, is_hdmi21 = 0;
+
+	/* pre-calculation */
+	if (dir == XHDMIPHY_DIR_RX) {
+		refclk_ptr = &inst->rx_refclk_hz;
+		is_hdmi21 = inst->rx_hdmi21_cfg.is_en;
+		tmdsclk_ratio = inst->rx_tmdsclock_ratio;
+
+		/* calculate line rate */
+		if (is_hdmi21)
+			linerate = inst->rx_hdmi21_cfg.linerate;
+		else
+			linerate = (u64)(*refclk_ptr) *
+				   ((tmdsclk_ratio ? 40 : 10));
+
+		inst->rx_dru_enabled = 0;
+
+		/* enable DRU based on incoming REFCLK */
+		if (!is_hdmi21 && !tmdsclk_ratio &&
+		    inst->rx_refclk_hz < XHDMIPHY_LCPLL_MIN_REFCLK) {
+			if (inst->conf.dru_present) {
+				/* check DRU frequency */
+				if (xhdmiphy_get_dru_refclk(inst) == 1) {
+					dev_err(inst->dev,
+						"cannot get dru refclk\n");
+					return 1;
+				}
+
+				inst->rx_dru_enabled = 1;
+				linerate = XHDMIPHY_HDMI_GTYE5_DRU_LRATE;
+			} else {
+				dev_err(inst->dev, "dru is not present\n");
+				return 1;
+			}
+		}
+	} else {
+		refclk_ptr = &inst->tx_refclk_hz;
+		is_hdmi21 = inst->tx_hdmi21_cfg.is_en;
+		inst->tx_samplerate = 1;
+
+		if (!is_hdmi21) {
+			/* Determine if HDMI 2.0 mode */
+			if (*refclk_ptr >= XHDMIPHY_HDMI20_REFCLK_RANGE7) {
+				tmdsclk_ratio = 1;
+				(*refclk_ptr) = (*refclk_ptr) / 4;
+			} else if (*refclk_ptr >=
+				   XHDMIPHY_HDMI20_REFCLK_RANGE5) {
+			/* check for x1 Over sampling mode */
+				inst->tx_samplerate = 1;
+			} else if (*refclk_ptr >=
+				   XHDMIPHY_HDMI20_REFCLK_RANGE3) {
+			/* check for x2 Over sampling mode */
+				inst->tx_samplerate = 2;
+				(*refclk_ptr) = (*refclk_ptr) * 2;
+			} else if (*refclk_ptr >=
+				   XHDMIPHY_HDMI20_REFCLK_RANGE1) {
+			/* check for x3 Over sampling mode */
+				inst->tx_samplerate = 3;
+				(*refclk_ptr) = (*refclk_ptr) * 3;
+			} else if (*refclk_ptr <
+				   XHDMIPHY_HDMI20_REFCLK_RANGE1) {
+			/* check for x5 Over sampling mode */
+				inst->tx_samplerate = 5;
+				(*refclk_ptr) = (*refclk_ptr) * 5;
+			}
+		}
+
+		if (is_hdmi21)
+			linerate = inst->tx_hdmi21_cfg.linerate;
+		else
+			linerate = (u64)(*refclk_ptr) *
+						((tmdsclk_ratio ? 40 : 10));
+	}
+
+	/* check for DRU mode */
+	if (dir == XHDMIPHY_DIR_RX &&
+	    inst->rx_dru_enabled) {
+		inst->quad.lcpll.linerate_cfg = 0;
+	} else if (!is_hdmi21) {
+		/* check for HDMI 1.4/2.0 GT linerate config */
+		/* HDMI 1.4 */
+		if (!tmdsclk_ratio) {
+			if ((XHDMIPHY_HDMI14_REFCLK_RANGE1 <= (*refclk_ptr)) &&
+			    ((*refclk_ptr) <= XHDMIPHY_HDMI14_REFCLK_RANGE2)) {
+				inst->quad.lcpll.linerate_cfg = 1;
+			} else if ((XHDMIPHY_HDMI14_REFCLK_RANGE3 <= (*refclk_ptr)) &&
+						/* 297 MHz + 0.5% + 10 KHz error */
+						((*refclk_ptr) <=
+						 XHDMIPHY_HDMI14_REFCLK_RANGE3)) {
+				inst->quad.lcpll.linerate_cfg = 2;
+			} else {
+				status = 1;
+			}
+		} else {
+			/* HDMI 2.0 */
+			if ((XHDMIPHY_HDMI20_REFCLK_RANGE2 <= (*refclk_ptr)) &&
+			    ((*refclk_ptr) <= XHDMIPHY_HDMI20_REFCLK_RANGE4)) {
+				inst->quad.lcpll.linerate_cfg = 3;
+			} else if ((XHDMIPHY_HDMI20_REFCLK_RANGE4 <= (*refclk_ptr)) &&
+				   ((*refclk_ptr) <=
+				    XHDMIPHY_HDMI20_REFCLK_RANGE6)) {
+				inst->quad.lcpll.linerate_cfg = 4;
+			} else {
+				status = 1;
+			}
+		}
+	} else if (is_hdmi21) {
+		/* check for HDMI 2.1 GT linerate config */
+		if (linerate == XHDMIPHY_LRATE_3G)
+			inst->quad.lcpll.linerate_cfg = 5;
+		else if (linerate == XHDMIPHY_LRATE_6G)
+			inst->quad.lcpll.linerate_cfg = 6;
+		else if (linerate == XHDMIPHY_LRATE_8G)
+			inst->quad.lcpll.linerate_cfg = 7;
+		else if (linerate == XHDMIPHY_LRATE_10G)
+			inst->quad.lcpll.linerate_cfg = 8;
+		else if (linerate == XHDMIPHY_LRATE_12G)
+			inst->quad.lcpll.linerate_cfg = 9;
+		else
+			status = 1;
+	}
+
+	xhdmiphy_cfg_linerate(inst, XHDMIPHY_CHID_CMN0, linerate);
+
+	if (status == 1)
+		dev_err(inst->dev, "failed to configure lcpll params\n");
+
+	return status;
+}
+
+/**
+ * xhdmiphy_rpll_param - This function calculates the rpll parameters.
+ *
+ * @inst:	inst is a pointer to the HDMI GT core instance
+ * @chid:	chid is the channel Id to operate on
+ * @dir:	dir is an indicator for Rx or Tx
+ *
+ * @return:	- 0 if calculated RPLL parameters updated successfully
+ *		- 1 if parameters not updated
+ */
+static u32 xhdmiphy_rpll_param(struct xhdmiphy_dev *inst, enum chid chid,
+			       enum dir dir)
+{
+	u64 linerate = 0;
+	u32 status = 0;
+	u32 *refclk_ptr;
+	u8 tmdsclk_ratio = 0, is_hdmi21 = 0;
+
+	/* Pre-calculation */
+	if (dir == XHDMIPHY_DIR_RX) {
+		refclk_ptr = &inst->rx_refclk_hz;
+		is_hdmi21 = inst->tx_hdmi21_cfg.is_en;
+		tmdsclk_ratio = inst->rx_tmdsclock_ratio;
+
+		/* calculate line rate */
+		if (is_hdmi21) {
+			linerate = inst->rx_hdmi21_cfg.linerate;
+		} else {
+			linerate = (u64)(*refclk_ptr) *
+						((tmdsclk_ratio ? 40 : 10));
+		}
+
+		inst->rx_dru_enabled = 0;
+
+		/* enable DRU based on incoming REFCLK */
+		if (!is_hdmi21 && !tmdsclk_ratio &&
+		    inst->rx_refclk_hz < XHDMIPHY_RPLL_MIN_REFCLK) {
+			if (inst->conf.dru_present) {
+				/* check DRU frequency */
+				if (xhdmiphy_get_dru_refclk(inst) == 1) {
+					dev_err(inst->dev,
+						"cannot get dru refclk\n");
+					return 1;
+				}
+
+				inst->rx_dru_enabled = 1;
+				linerate = XHDMIPHY_HDMI_GTYE5_DRU_LRATE;
+			} else {
+				dev_err(inst->dev, "dru is not present\n");
+				return 1;
+			}
+		}
+	} else {
+		refclk_ptr = &inst->tx_refclk_hz;
+		is_hdmi21 = inst->tx_hdmi21_cfg.is_en;
+		inst->tx_samplerate = 1;
+
+		if (!is_hdmi21) {
+			/* determine if HDMI 2.0 mode */
+			if (*refclk_ptr >= XHDMIPHY_HDMI20_REFCLK_RANGE7) {
+				tmdsclk_ratio = 1;
+				(*refclk_ptr) = (*refclk_ptr) / 4;
+			} else if (*refclk_ptr >=
+				   XHDMIPHY_HDMI20_REFCLK_RANGE5) {
+			/* check for x1 over sampling mode */
+				inst->tx_samplerate = 1;
+			} else if (*refclk_ptr >=
+				   XHDMIPHY_HDMI20_REFCLK_RANGE3) {
+			/* check for x2 Over sampling mode */
+				inst->tx_samplerate = 2;
+				(*refclk_ptr) = (*refclk_ptr) * 2;
+			} else if (*refclk_ptr >=
+				   XHDMIPHY_HDMI20_REFCLK_RANGE1) {
+			/* check for x3 Over sampling mode */
+				inst->tx_samplerate = 3;
+				(*refclk_ptr) = (*refclk_ptr) * 3;
+			/* check for x5 Over sampling mode */
+			} else if (*refclk_ptr <
+				   XHDMIPHY_HDMI20_REFCLK_RANGE1) {
+				inst->tx_samplerate = 5;
+				(*refclk_ptr) = (*refclk_ptr) * 5;
+			}
+		}
+
+		/* calculate line rate */
+		if (is_hdmi21)
+			linerate = inst->tx_hdmi21_cfg.linerate;
+		else
+			linerate = (u64)(*refclk_ptr) * ((tmdsclk_ratio ? 40 : 10));
+	}
+
+	/* check for DRU mode */
+	if (dir == XHDMIPHY_DIR_RX && inst->rx_dru_enabled) {
+		inst->quad.rpll.linerate_cfg = 0;
+	/* check for HDMI 1.4/2.0 GT linerate config */
+	} else if (!is_hdmi21) {
+		/* HDMI 1.4 */
+		if (!tmdsclk_ratio) {
+			if ((XHDMIPHY_HDMI14_REFCLK_RANGE1 <= (*refclk_ptr)) &&
+			    ((*refclk_ptr) <= 200000000)) {
+				inst->quad.rpll.linerate_cfg = 1;
+			} else if ((200000000 <= (*refclk_ptr)) &&
+				   ((*refclk_ptr) <=
+				    XHDMIPHY_HDMI14_REFCLK_RANGE3)) {
+				inst->quad.rpll.linerate_cfg = 2;
+			} else {
+				status = 1;
+			}
+		/* HDMI 2.0 */
+		} else {
+			if ((XHDMIPHY_HDMI20_REFCLK_RANGE2 <= (*refclk_ptr)) &&
+			    ((*refclk_ptr) <= 100000000)) {
+				inst->quad.rpll.linerate_cfg = 3;
+			} else if ((100000000 <= (*refclk_ptr)) &&
+				   ((*refclk_ptr) <=
+				    XHDMIPHY_HDMI20_REFCLK_RANGE6)) {
+				inst->quad.rpll.linerate_cfg = 4;
+			} else {
+				status = 1;
+			}
+		}
+	/* check for HDMI 2.1 gt linerate config */
+	} else if (is_hdmi21) {
+		if (linerate == XHDMIPHY_LRATE_3G)
+			inst->quad.rpll.linerate_cfg = 5;
+		else if (linerate == XHDMIPHY_LRATE_6G)
+			inst->quad.rpll.linerate_cfg = 6;
+		else if (linerate == XHDMIPHY_LRATE_8G)
+			inst->quad.rpll.linerate_cfg = 7;
+		else if (linerate == XHDMIPHY_LRATE_10G)
+			inst->quad.rpll.linerate_cfg = 8;
+		else if (linerate == XHDMIPHY_LRATE_12G)
+			inst->quad.rpll.linerate_cfg = 9;
+		else
+			status = 1;
+	}
+
+	/* update line rate value */
+	xhdmiphy_cfg_linerate(inst, XHDMIPHY_CHID_CMN1, linerate);
+	if (status == 1)
+		dev_err(inst->dev, "failed to configure rpll params\n");
+
+	return status;
+}
+
+/**
+ * xhdmiphy_txpll_param - This function calculates the Tx pll parameters.
+ *
+ * @inst:	inst is a pointer to the HDMI GT core instance
+ * @chid:	chid is the channel ID to operate on
+ *
+ * @return:	- 0 if calculated qpll parameters updated successfully
+ *		- 1 if parameters not updated
+ */
+static u32 xhdmiphy_txpll_param(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	enum pll_type pll_type;
+
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					 XHDMIPHY_CHID_CH1);
+
+	if (pll_type == XHDMIPHY_PLL_LCPLL)
+		return xhdmiphy_lcpll_param(inst, chid, XHDMIPHY_DIR_TX);
+
+	return xhdmiphy_rpll_param(inst, chid, XHDMIPHY_DIR_TX);
+}
+
+/**
+ * xhdmiphy_rxpll_param - This function calculates the Rx pll parameters.
+ *
+ * @inst:	inst is a pointer to the HDMI GT core instance
+ * @chid:	chid is the channel id to operate on
+ *
+ * @return:	- 0 if calculated qpll parameters updated
+ *		successfully
+ *		- 1 if parameters not updated
+ */
+static bool xhdmiphy_rxpll_param(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	enum pll_type pll_type;
+
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+					 XHDMIPHY_CHID_CH1);
+
+	if (pll_type == XHDMIPHY_PLL_LCPLL)
+		return xhdmiphy_lcpll_param(inst, chid, XHDMIPHY_DIR_RX);
+
+	return xhdmiphy_rpll_param(inst, chid, XHDMIPHY_DIR_RX);
+}
+
+/**
+ * xhdmiphy_set_tx_param - This function update/set the HDMI TX parameter.
+ *
+ * @inst:		is a pointer to the Hdmiphy core instance
+ * @chid:		chid is the channel ID to operate on
+ * @ppc:		ppc is the pixels per clock to set
+ * @bpc:		bpc is the bits per color to set
+ * @fmt:		fmt is the color format to set
+ *
+ * @return:
+ *		- 0 if TX parameters set/updated
+ *		- gc if low resolution video not supported
+ */
+u32 xhdmiphy_set_tx_param(struct xhdmiphy_dev *inst, enum chid chid,
+			  enum ppc ppc, enum color_depth bpc,
+			  enum color_fmt fmt)
+{
+	u32 status;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		/*
+		 * only calculate the QPLL/CPLL parameters when the GT TX and
+		 * RX are not coupled
+		 */
+		if (xhdmiphy_is_tx_using_cpll(inst, chid)) {
+			status = xhdmiphy_cpll_param(inst, chid, XHDMIPHY_DIR_TX);
+		} else {
+			status = xhdmiphy_qpll_param(inst, chid, XHDMIPHY_DIR_TX);
+			/* update sysClk and PLL clk registers immediately */
+			xhdmiphy_write_refclksel(inst);
+		}
+	} else {
+		status = xhdmiphy_txpll_param(inst, chid);
+	}
+
+	if (status == 1)
+		return status;
+
+	/* Is HDMITXSS PPC match with HDMIPHY PPC? */
+	if (ppc == inst->conf.ppc) {
+		status = 0;
+	} else {
+		dev_err(inst->dev,
+			"HDMITXSS ppc does't match with hdmiphy ppc\n");
+		status = 1;
+	}
+	if (status == 0) {
+		/* HDMI 2.1 */
+		if (inst->tx_hdmi21_cfg.is_en) {
+			xhdmiphy_mmcm_param(inst, XHDMIPHY_DIR_TX);
+
+			return status;
+		}
+
+		/*
+		 * calculate TXPLL parameters.
+		 * In HDMI the colordepth in YUV422 is always 12 bits,
+		 * although on the link itself it is being transmitted as
+		 * 8-bits. Therefore if the colorspace is YUV422, then force the
+		 * colordepth to 8 bits.
+		 */
+		if (fmt == XVIDC_CSF_YCRCB_422) {
+			status = xhdmiphy_cal_mmcm_param(inst, chid,
+							 XHDMIPHY_DIR_TX, ppc,
+							 XVIDC_BPC_8);
+		} else {
+			status = xhdmiphy_cal_mmcm_param(inst, chid,
+							 XHDMIPHY_DIR_TX, ppc,
+							 bpc);
+		}
+	} else {
+		status = 1;
+	}
+
+	return status;
+}
+
+static u32 xhdmiphy_set_rx_param(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	u64 dru_center_freq;
+	u32 status;
+	enum chid ch_id = chid;
+	enum pll_type pll_type;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		if (xhdmiphy_is_rx_using_cpll(inst, chid)) {
+			status = xhdmiphy_cpll_param(inst, chid,
+						     XHDMIPHY_DIR_RX);
+		} else {
+			status = xhdmiphy_qpll_param(inst, chid,
+						     XHDMIPHY_DIR_RX);
+			/* update SysClk and PLL clk registers immediately */
+			xhdmiphy_write_refclksel(inst);
+		}
+	} else {
+		status = xhdmiphy_rxpll_param(inst, chid);
+	}
+
+	if (inst->rx_dru_enabled) {
+		pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+						 XHDMIPHY_CHID_CH1);
+		/* update the chid */
+		ch_id = xhdmiphy_get_rcfg_chid(pll_type);
+		dru_center_freq = xhdmiphy_dru_cal_centerfreq(inst, ch_id);
+		xhdmiphy_set_dru_centerfreq(inst, XHDMIPHY_CHID_CHA,
+					    dru_center_freq);
+	}
+
+	return status;
+}
+
+static void xhdmiphy_tx_timertimeout_handler(struct xhdmiphy_dev *inst)
+{
+	enum chid chid;
+	enum pll_type pll_type;
+	u8 val_cmp, id, id0, id1;
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+						 XHDMIPHY_CHID_CH1);
+		/* determine which channel(s) to operate on */
+		chid = xhdmiphy_get_rcfg_chid(pll_type);
+		xhdmiphy_mmcm_start(inst, XHDMIPHY_DIR_TX);
+		xhdmiphy_powerdown_gtpll(inst, (pll_type == XHDMIPHY_PLL_CPLL) ?
+					       XHDMIPHY_CHID_CHA :
+					       XHDMIPHY_CHID_CMNA,
+					       false);
+
+		if (pll_type != XHDMIPHY_PLL_CPLL)
+			xhdmiphy_write_refclksel(inst);
+
+		xhdmiphy_clk_reconf(inst, chid);
+		xhdmiphy_outdiv_reconf(inst, XHDMIPHY_CHID_CHA,
+				       XHDMIPHY_DIR_TX);
+		if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTHE4 ||
+		    inst->conf.gt_type == XHDMIPHY_GTTYPE_GTYE4) {
+			xhdmiphy_set_bufgtdiv(inst, XHDMIPHY_DIR_TX,
+					      (pll_type == XHDMIPHY_PLL_CPLL) ?
+					      inst->quad.plls->tx_outdiv :
+					      (inst->quad.plls->tx_outdiv != 16) ?
+					      inst->quad.plls->tx_outdiv :
+					      inst->quad.plls->tx_outdiv / 2);
+		}
+
+		xhdmiphy_dir_reconf(inst, XHDMIPHY_CHID_CHA,
+				    XHDMIPHY_DIR_TX);
+		/* assert PLL reset */
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_TX, true);
+		/* de-assert PLL reset */
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_TX, false);
+
+		if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTHE4 ||
+		    inst->conf.gt_type == XHDMIPHY_GTTYPE_GTYE4) {
+			xhdmiphy_tx_align_start(inst, chid, false);
+		}
+
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+		for (id = id0; id <= id1; id++) {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_LOCK;
+		}
+	} else {
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+		for (id = id0; id <= id1; id++) {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+						XHDMIPHY_GT_STATE_GPO_RE;
+		}
+		/* compare the current and next CFG values */
+		val_cmp = xhdmiphy_check_linerate_cfg(inst,
+						      XHDMIPHY_CHID_CH1,
+						      XHDMIPHY_DIR_TX);
+		if (!val_cmp) {
+			xhdmiphy_set_gpi(inst, XHDMIPHY_CHID_CHA,
+					 XHDMIPHY_DIR_TX, true);
+		} else {
+			xhdmiphy_txgpo_risingedge_handler(inst);
+		}
+	}
+}
+
+static void xhdmiphy_rxgpo_risingedge_handler(struct xhdmiphy_dev *inst)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_check_linerate_cfg(inst, XHDMIPHY_CHID_CH1, XHDMIPHY_DIR_RX);
+	/* De-assert GPI port. */
+	xhdmiphy_set_gpi(inst, XHDMIPHY_CHID_CHA,
+			 XHDMIPHY_DIR_RX, false);
+
+	/* Wait for GPO RX = 0 */
+	while (xhdmiphy_get_gpo(inst, XHDMIPHY_CHID_CHA, XHDMIPHY_DIR_RX))
+		;
+
+	/* Configure RXRATE Port */
+	xhdmiphy_dir_reconf(inst, XHDMIPHY_CHID_CHA, XHDMIPHY_DIR_RX);
+	/* Deassert reset on GT Reset IP RX */
+	xhdmiphy_write(inst, XHDMIPHY_COMMON_INIT_REG,
+		       (xhdmiphy_read(inst,
+		       XHDMIPHY_COMMON_INIT_REG) & ~0x2));
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++) {
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+						XHDMIPHY_GT_STATE_LOCK;
+	}
+}
+
+static void xhdmiphy_rx_timertimeout_handler(struct xhdmiphy_dev *inst)
+{
+	enum chid chid;
+	enum pll_type pll_type;
+	u32 status;
+	u8 id, id0, id1, val_cmp;
+
+	if (!inst->rx_hdmi21_cfg.is_en) {
+		dev_info(inst->dev, "xhdmi 2.0 protocl is enabled\n");
+	} else {
+		if (inst->conf.rx_refclk_sel == inst->conf.rx_frl_refclk_sel) {
+			xhdmiphy_mmcm_clkin_sel(inst, XHDMIPHY_DIR_RX,
+						XHDMIPHY_MMCM_CLKINSEL_CLKIN1);
+			xhdmiphy_mmcm_start(inst, XHDMIPHY_DIR_RX);
+		}
+	}
+
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+					 XHDMIPHY_CHID_CH1);
+	/* determine which channel(s) to operate on */
+	chid = xhdmiphy_get_rcfg_chid(pll_type);
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+
+	status = xhdmiphy_set_rx_param(inst, chid);
+	if (status != 0) {
+		for (id = id0; id <= id1; id++) {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_IDLE;
+		}
+
+		return;
+	}
+
+	/* enable DRU to set the clock muxes */
+	xhdmiphy_dru_en(inst, XHDMIPHY_CHID_CHA, inst->rx_dru_enabled);
+
+	xhdmiphy_dru_mode_en(inst, inst->rx_dru_enabled);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		/* enable PLL */
+		xhdmiphy_powerdown_gtpll(inst, (pll_type == XHDMIPHY_PLL_CPLL) ?
+					 XHDMIPHY_CHID_CHA :
+					 XHDMIPHY_CHID_CMNA, false);
+
+		/* update reference clock election */
+		if (!inst->rx_hdmi21_cfg.is_en) {
+			xhdmiphy_pll_refclk_sel(inst,
+						((pll_type == XHDMIPHY_PLL_CPLL) ?
+						XHDMIPHY_CHID_CHA :
+						XHDMIPHY_CHID_CMNA),
+						((inst->rx_dru_enabled) ?
+						inst->conf.dru_refclk_sel :
+						inst->conf.rx_refclk_sel));
+		}
+		xhdmiphy_write_refclksel(inst);
+
+		pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+						 XHDMIPHY_CHID_CH1);
+		/* determine which channel(s) to operate on */
+		chid = xhdmiphy_get_rcfg_chid(pll_type);
+		xhdmiphy_clk_reconf(inst, chid);
+		xhdmiphy_outdiv_reconf(inst, XHDMIPHY_CHID_CHA,
+				       XHDMIPHY_DIR_RX);
+		xhdmiphy_dir_reconf(inst, XHDMIPHY_CHID_CHA,
+				    XHDMIPHY_DIR_RX);
+		/* assert RX PLL reset */
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_RX, true);
+		/* de-assert RX PLL reset */
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_RX, false);
+		for (id = id0; id <= id1; id++) {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_LOCK;
+		}
+	} else {
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+		for (id = id0; id <= id1; id++) {
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+						XHDMIPHY_GT_STATE_GPO_RE;
+		}
+
+		/* compare the current and next CFG values */
+		val_cmp = xhdmiphy_check_linerate_cfg(inst, XHDMIPHY_CHID_CH1,
+						      XHDMIPHY_DIR_RX);
+		if (!val_cmp) {
+			xhdmiphy_set_gpi(inst, XHDMIPHY_CHID_CHA,
+					 XHDMIPHY_DIR_RX, true);
+		} else {
+			xhdmiphy_rxgpo_risingedge_handler(inst);
+		}
+	}
+}
+
+void xhdmiphy_hdmi20_conf(struct xhdmiphy_dev *inst, enum dir dir)
+{
+	enum pll_type pll_type;
+
+	pll_type = xhdmiphy_get_pll_type(inst, dir, XHDMIPHY_CHID_CH1);
+
+	if (dir == XHDMIPHY_DIR_TX) {
+		inst->tx_hdmi21_cfg.linerate = 0;
+		inst->tx_hdmi21_cfg.nchannels = 0;
+		inst->tx_hdmi21_cfg.is_en = false;
+	} else {
+		inst->rx_hdmi21_cfg.linerate = 0;
+		inst->rx_hdmi21_cfg.nchannels = 0;
+		inst->rx_hdmi21_cfg.is_en = false;
+	}
+
+	xhdmiphy_mmcm_clkin_sel(inst, dir, XHDMIPHY_MMCM_CLKINSEL_CLKIN1);
+
+	if (dir == XHDMIPHY_DIR_TX)
+		xhdmiphy_intr_en(inst, XHDMIPHY_INTR_TXFREQCHANGE_MASK);
+	else
+		xhdmiphy_intr_en(inst, XHDMIPHY_INTR_RXFREQCHANGE_MASK);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		xhdmiphy_pll_refclk_sel(inst, ((pll_type == XHDMIPHY_PLL_CPLL) ?
+					XHDMIPHY_CHID_CHA : XHDMIPHY_CHID_CMNA),
+					((dir == XHDMIPHY_DIR_TX) ?
+					inst->conf.tx_refclk_sel :
+					inst->conf.rx_refclk_sel));
+		xhdmiphy_write_refclksel(inst);
+	}
+}
+
+/**
+ * xhdmiphy_hdmi21_conf - This function will configure the GT for HDMI 2.1
+ * operation
+ *
+ * @inst:	inst is a pointer to the Hdmiphy core instance
+ * @dir:	chid is the channel ID to operate on
+ * @linerate:	dir is an indicator for RX or TX
+ * @nchannels:	no of channels
+ *
+ * @return:	- 0 if Tx parameters set/updated
+ *		- 1 if low resolution video not supported
+ */
+u32 xhdmiphy_hdmi21_conf(struct xhdmiphy_dev *inst, enum dir dir, u64 linerate,
+			 u8 nchannels)
+{
+	enum pll_type pll_type;
+	u32 status = 0;
+
+	if (inst->conf.gt_type == XHDMIPHY_GTHE4 ||
+	    inst->conf.gt_type == XHDMIPHY_GTYE4) {
+		char speedgrade[5] = "-2";
+		char comp_val[5] = "-1";
+		char *speed_grade_ptr = &speedgrade[0];
+		char *compval_ptr = &comp_val[0];
+
+		if (strncmp(speed_grade_ptr, compval_ptr, 2) == 0) {
+			if (linerate > XHDMIPHY_LRATE_8G) {
+				dev_err(inst->dev, "linkrate is not supported\n");
+				return 1;
+			}
+		}
+	}
+
+	pll_type = xhdmiphy_get_pll_type(inst, dir, XHDMIPHY_CHID_CH1);
+	if (dir == XHDMIPHY_DIR_TX) {
+		if (inst->conf.tx_refclk_sel != inst->conf.tx_frl_refclk_sel)
+			xhdmiphy_intr_dis(inst,
+					  XHDMIPHY_INTR_TXFREQCHANGE_MASK);
+
+		/* enable 4th channel output */
+		xhdmiphy_clkout1_obuftds_en(inst, XHDMIPHY_DIR_TX, (true));
+	} else {
+		if (inst->conf.rx_refclk_sel != inst->conf.rx_frl_refclk_sel)
+			xhdmiphy_intr_dis(inst, XHDMIPHY_INTR_RXFREQCHANGE_MASK);
+	}
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		xhdmiphy_pll_refclk_sel(inst, ((pll_type == XHDMIPHY_PLL_CPLL) ?
+					XHDMIPHY_CHID_CHA : XHDMIPHY_CHID_CMNA),
+					((dir == XHDMIPHY_DIR_TX) ?
+					inst->conf.tx_frl_refclk_sel :
+					inst->conf.rx_frl_refclk_sel));
+
+		xhdmiphy_write_refclksel(inst);
+	}
+
+	/* update HDMI confurations */
+	if (dir == XHDMIPHY_DIR_TX) {
+		inst->tx_refclk_hz = XHDMIPHY_HDMI21_FRL_REFCLK;
+		inst->tx_hdmi21_cfg.linerate = linerate;
+		inst->tx_hdmi21_cfg.nchannels = nchannels;
+		inst->tx_hdmi21_cfg.is_en = true;
+
+		status = xhdmiphy_set_tx_param(inst,
+					       ((pll_type == XHDMIPHY_PLL_CPLL) ?
+					       XHDMIPHY_CHID_CHA :
+					       XHDMIPHY_CHID_CMNA),
+					       inst->conf.ppc, XVIDC_BPC_8,
+					       XVIDC_CSF_RGB);
+
+		xhdmiphy_mmcm_lock_en(inst, dir, true);
+
+		if (inst->conf.tx_refclk_sel == inst->conf.tx_frl_refclk_sel)
+			xhdmiphy_mmcm_clkin_sel(inst, dir,
+						XHDMIPHY_MMCM_CLKINSEL_CLKIN1);
+		else
+			xhdmiphy_mmcm_clkin_sel(inst, dir,
+						XHDMIPHY_MMCM_CLKINSEL_CLKIN2);
+
+		if (inst->conf.tx_refclk_sel != inst->conf.tx_frl_refclk_sel)
+			xhdmiphy_tx_timertimeout_handler(inst);
+	} else {
+		inst->rx_refclk_hz = XHDMIPHY_HDMI21_FRL_REFCLK;
+		inst->rx_hdmi21_cfg.linerate = linerate;
+		inst->rx_hdmi21_cfg.nchannels = nchannels;
+		inst->rx_hdmi21_cfg.is_en = true;
+
+		/* set mmcm dividers for frl mode */
+		xhdmiphy_mmcm_param(inst, XHDMIPHY_DIR_RX);
+
+		/* mask the mmcm lock */
+		xhdmiphy_mmcm_lock_en(inst, dir, true);
+
+		if (inst->conf.rx_refclk_sel != inst->conf.rx_frl_refclk_sel) {
+			/* set mmcm clkinsel to clk2 */
+			xhdmiphy_mmcm_clkin_sel(inst, dir,
+						XHDMIPHY_MMCM_CLKINSEL_CLKIN2);
+
+			xhdmiphy_mmcm_start(inst, XHDMIPHY_DIR_RX);
+
+			xhdmiphy_rx_timertimeout_handler(inst);
+		}
+	}
+
+	return status;
+}
+
+/**
+ * xhdmiphy_is_pll_locked - This function will check the status of a PLL lock
+ * on the specified channel.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID which to operate on
+ *
+ * @return:	- true if the specified PLL is locked
+ *		- false otherwise
+ */
+static bool xhdmiphy_is_pll_locked(struct xhdmiphy_dev *inst, enum chid chid)
+{
+	u32 reg_val, mask_val;
+	enum pll_type tx_pll, rx_pll;
+
+	if (chid == XHDMIPHY_CHID_CMN0) {
+		if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+			mask_val = XHDMIPHY_PLL_LOCK_STATUS_QPLL0_MASK;
+		else
+			mask_val = XHDMIPHY_PLL_LOCK_STATUS_LCPLL_MASK;
+	} else if ((chid == XHDMIPHY_CHID_CMN1) &&
+		   (inst->conf.gt_type != XHDMIPHY_GTYE5)) {
+		mask_val = XHDMIPHY_PLL_LOCK_STATUS_QPLL1_MASK;
+	} else if (chid == XHDMIPHY_CHID_CMN1) {
+		mask_val = XHDMIPHY_PLL_LOCK_STATUS_RPLL_MASK;
+	} else {
+		/* This will result to 1 */
+		mask_val = XHDMIPHY_PLL_LOCK_STATUS_CPLL_ALL_MASK;
+	}
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		if (chid == XHDMIPHY_CHID_CMNA) {
+			mask_val = XHDMIPHY_PLL_LOCK_STATUS_QPLL0_MASK |
+				   XHDMIPHY_PLL_LOCK_STATUS_QPLL1_MASK;
+		} else if (chid == XHDMIPHY_CHID_CHA) {
+			tx_pll = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+						       XHDMIPHY_CHID_CH1);
+			rx_pll = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+						       XHDMIPHY_CHID_CH1);
+			if (rx_pll == XHDMIPHY_PLL_CPLL &&
+			    xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_RX)) {
+				mask_val = XHDMIPHY_PLL_LOCK_STATUS_CPLL_HDMI_MASK;
+			} else if (tx_pll == XHDMIPHY_PLL_CPLL &&
+				   xhdmiphy_is_hdmi(inst, XHDMIPHY_DIR_TX)) {
+				mask_val = XHDMIPHY_PLL_LOCK_STATUS_CPLL_HDMI_MASK;
+			} else {
+				mask_val = XHDMIPHY_PLL_LOCK_STATUS_CPLL_ALL_MASK;
+			}
+		} else {
+			mask_val = XHDMIPHY_PLL_LOCK_STATUS_CPLL_MASK(chid);
+		}
+	}
+
+	reg_val = xhdmiphy_read(inst, XHDMIPHY_PLL_LOCK_STATUS_REG);
+
+	if ((reg_val & mask_val) == mask_val)
+		return false;
+
+	return true;
+}
+
+static void xhdmiphy_lcpll_lock_handler(struct xhdmiphy_dev *inst)
+{
+	enum pll_type tx_pll_type;
+	enum chid chid;
+	u8 id, id0, id1;
+
+	tx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					    XHDMIPHY_CHID_CH1);
+
+	/* Determine which channel(s) to operate on */
+	chid = xhdmiphy_get_rcfg_chid(XHDMIPHY_PLL_LCPLL);
+	if (xhdmiphy_is_pll_locked(inst, chid) == 0) {
+		dev_info(inst->dev, "lcpll is locked\n");
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+		for (id = id0; id <= id1; id++) {
+			if (tx_pll_type == XHDMIPHY_PLL_LCPLL)
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_RESET;
+			else
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_RESET;
+		}
+	} else {
+		dev_info(inst->dev, "lcpll lock lost !\n");
+	}
+}
+
+static void xhdmiphy_rpll_lock_handler(struct xhdmiphy_dev *inst)
+{
+	enum chid chid;
+	enum pll_type tx_pll_type;
+	u8 id, id0, id1;
+
+	tx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					    XHDMIPHY_CHID_CH1);
+	/* determine which channel(s) to operate on */
+	chid = xhdmiphy_get_rcfg_chid(XHDMIPHY_PLL_RPLL);
+	if (xhdmiphy_is_pll_locked(inst, chid) == 0) {
+		dev_info(inst->dev, "rpll is locked\n");
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+		for (id = id0; id <= id1; id++) {
+			if (tx_pll_type == XHDMIPHY_PLL_RPLL) {
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_RESET;
+			} else {
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_RESET;
+			}
+		}
+	} else {
+		dev_info(inst->dev, "rpll lock lost !\n");
+	}
+}
+
+/**
+ * xhdmiphy_rst_gt_txrx - This function will reset the GT's TX/RX logic.
+ *
+ * @inst:	inst is a pointer to the xhdmiphy core instance
+ * @chid:	chid is the channel ID which to operate on
+ * @dir:	dir is an indicator for TX or RX
+ * @hold:	hold is an indicator whether to "hold" the reset if set to 1
+ *		If set to 0: reset, then enable
+ */
+void xhdmiphy_rst_gt_txrx(struct xhdmiphy_dev *inst, enum chid chid,
+			  enum dir dir, u8 hold)
+{
+	u32 reg_val, mask_val, reg_off;
+
+	if (dir == XHDMIPHY_DIR_TX)
+		reg_off = XHDMIPHY_TX_INIT_REG;
+	else
+		reg_off = XHDMIPHY_RX_INIT_REG;
+
+	if (chid == XHDMIPHY_CHID_CHA)
+		mask_val = XHDMIPHY_TXRX_INIT_GTRESET_ALL_MASK;
+	else
+		mask_val = XHDMIPHY_TXRX_INIT_GTRESET_MASK(chid);
+
+	reg_val = xhdmiphy_read(inst, reg_off);
+	reg_val |= mask_val;
+	xhdmiphy_write(inst, reg_off, reg_val);
+
+	if (!hold) {
+		reg_val &= ~mask_val;
+		xhdmiphy_write(inst, reg_off, reg_val);
+	}
+}
+
+static void xhdmiphy_qpll_lock_handler(struct xhdmiphy_dev *inst)
+{
+	enum chid chid;
+	enum pll_type tx_pll_type, rx_pll_type;
+	u8 id, id0, id1;
+
+	tx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					    XHDMIPHY_CHID_CH1);
+	rx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+					    XHDMIPHY_CHID_CH1);
+
+	/* rX is using QPLL */
+	if (rx_pll_type == XHDMIPHY_PLL_QPLL ||
+	    rx_pll_type == XHDMIPHY_PLL_QPLL0 ||
+	    rx_pll_type == XHDMIPHY_PLL_QPLL1) {
+		chid = xhdmiphy_get_rcfg_chid(rx_pll_type);
+
+		if (xhdmiphy_is_pll_locked(inst, chid) == 0) {
+			dev_info(inst->dev, "qpll is locked\n");
+			xhdmiphy_rst_gt_txrx(inst, XHDMIPHY_CHID_CHA,
+					     XHDMIPHY_DIR_RX, false);
+			xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+			for (id = id0; id <= id1; id++)
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_RESET;
+
+		} else {
+			dev_info(inst->dev, "qpll lock lost!\n");
+		}
+	} else {
+		/* tX is using QPLL */
+		chid = xhdmiphy_get_rcfg_chid(tx_pll_type);
+		if (xhdmiphy_is_pll_locked(inst, chid) == 0) {
+			dev_info(inst->dev, "qpll locked\n");
+			xhdmiphy_rst_gt_txrx(inst, XHDMIPHY_CHID_CHA,
+					     XHDMIPHY_DIR_TX, false);
+			xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0,
+					&id1);
+			for (id = id0; id <= id1; id++) {
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_RESET;
+			}
+		} else {
+			dev_info(inst->dev, "qpll lock lost !\n");
+		}
+	}
+}
+
+static void xhdmiphy_cpll_lock_handler(struct xhdmiphy_dev *inst)
+{
+	enum pll_type tx_pll_type;
+	enum pll_type rx_pll_type;
+	enum chid chid;
+	u8 id, id0, id1;
+
+	tx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					    XHDMIPHY_CHID_CH1);
+	rx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+					    XHDMIPHY_CHID_CH1);
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+
+	if (rx_pll_type == XHDMIPHY_PLL_CPLL) {
+		chid = xhdmiphy_get_rcfg_chid(rx_pll_type);
+		if (xhdmiphy_is_pll_locked(inst, chid) == 0) {
+			dev_info(inst->dev, "cpll locked\n");
+			xhdmiphy_rst_gt_txrx(inst, XHDMIPHY_CHID_CHA,
+					     XHDMIPHY_DIR_RX, false);
+			for (id = id0; id <= id1; id++) {
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_RESET;
+			}
+		} else {
+			dev_info(inst->dev, "cpll lock lost\n");
+		}
+	} else {
+		/*
+		 * TX is using CPLL. Determine which channel(s)
+		 * to operate on
+		 */
+		chid = xhdmiphy_get_rcfg_chid(tx_pll_type);
+		if (xhdmiphy_is_pll_locked(inst, chid) == 0) {
+			dev_info(inst->dev, "cpll locked\n");
+			xhdmiphy_rst_gt_txrx(inst, XHDMIPHY_CHID_CHA,
+					     XHDMIPHY_DIR_TX, false);
+			for (id = id0; id <= id1; id++) {
+				inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_RESET;
+			}
+		} else {
+			dev_info(inst->dev, "cpll lock lost\n");
+		}
+	}
+}
+
+static void xhdmiphy_txgt_aligndone_handler(struct xhdmiphy_dev *inst)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+						XHDMIPHY_GT_STATE_READY;
+}
+
+static void xhdmiphy_txgt_rstdone_handler(struct xhdmiphy_dev *inst)
+{
+	enum pll_type pll_type;
+	enum chid chid;
+	u8 id, id0, id1;
+
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					 XHDMIPHY_CHID_CH1);
+	chid = xhdmiphy_get_rcfg_chid(pll_type);
+
+	/* Set TX TMDS Clock Pattern Generator */
+	if (inst->conf.gt_as_tx_tmdsclk &&
+	    (inst->tx_hdmi21_cfg.is_en == 0 ||
+	    (inst->tx_hdmi21_cfg.is_en == 1 &&
+	    inst->tx_hdmi21_cfg.nchannels == 3))) {
+		xhdmiphy_patgen_set_ratio(inst,
+					  (u64)((xhdmiphy_get_linerate(inst,
+					  chid)) / 1000000));
+		xhdmiphy_set(inst, XHDMIPHY_PATGEN_CTRL_REG,
+			     XHDMIPHY_PATGEN_CTRL_ENABLE_MASK);
+	} else {
+		xhdmiphy_clr(inst, XHDMIPHY_PATGEN_CTRL_REG,
+			     XHDMIPHY_PATGEN_CTRL_ENABLE_MASK);
+	}
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		if (inst->conf.gt_type == XHDMIPHY_GTTYPE_GTHE4 ||
+		    inst->conf.gt_type == XHDMIPHY_GTTYPE_GTYE4) {
+			xhdmiphy_tx_align_rst(inst, XHDMIPHY_CHID_CHA, true);
+			xhdmiphy_tx_align_rst(inst, XHDMIPHY_CHID_CHA, false);
+		}
+		/* GT alignment */
+		xhdmiphy_tx_align_start(inst, XHDMIPHY_CHID_CHA, true);
+		xhdmiphy_tx_align_start(inst, XHDMIPHY_CHID_CHA, false);
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+		for (id = id0; id <= id1; id++)
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+						XHDMIPHY_GT_STATE_ALIGN;
+	} else {
+		/* Deassert TX LNKRDY MASK */
+		xhdmiphy_write(inst, XHDMIPHY_TX_INIT_REG,
+			       (xhdmiphy_read(inst, XHDMIPHY_TX_INIT_REG) &
+			       ~XHDMIPHY_TXPCS_RESET_MASK));
+
+		xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+
+		for (id = id0; id <= id1; id++)
+			inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_READY;
+	}
+}
+
+static void xhdmiphy_rxgt_rstdone_handler(struct xhdmiphy_dev *inst)
+{
+	u8 id, id0, id1;
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+						XHDMIPHY_GT_STATE_READY;
+
+	xhdmiphy_write(inst, XHDMIPHY_RX_INIT_REG,
+		       (xhdmiphy_read(inst, XHDMIPHY_RX_INIT_REG) &
+		       ~XHDMIPHY_RXPCS_RESET_MASK));
+	if (inst->rx_dru_enabled)
+		xhdmiphy_dru_reset(inst, XHDMIPHY_CHID_CHA, false);
+
+	if (inst->phycb[RX_READY_CB].cb)
+		inst->phycb[RX_READY_CB].cb(inst->phycb[RX_READY_CB].data);
+}
+
+static void xhdmiphy_tx_freqchnage_handler(struct xhdmiphy_dev *inst)
+{
+	enum pll_type pll_type;
+	u8 id, id0, id1;
+
+	if (inst->tx_hdmi21_cfg.is_en) {
+		if (inst->conf.tx_refclk_sel != inst->conf.tx_frl_refclk_sel)
+			return;
+	}
+
+	/* set tX TMDS clock pattern generator */
+	if (inst->conf.gt_as_tx_tmdsclk &&
+	    (inst->tx_hdmi21_cfg.is_en == 0 ||
+	    (inst->tx_hdmi21_cfg.is_en == 1 &&
+	    inst->tx_hdmi21_cfg.nchannels == 3)))
+		xhdmiphy_clr(inst, XHDMIPHY_PATGEN_CTRL_REG,
+			     XHDMIPHY_PATGEN_CTRL_ENABLE_MASK);
+
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					 XHDMIPHY_CHID_CH1);
+
+	/* If the TX frequency has changed, the PLL is always disabled */
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		xhdmiphy_powerdown_gtpll(inst, (pll_type == XHDMIPHY_PLL_CPLL) ?
+					 XHDMIPHY_CHID_CHA :
+					 XHDMIPHY_CHID_CMNA, true);
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_TX, true);
+	} else {
+		/* Mask RESET DONE */
+		/* Deassert TX LNKRDY MASK */
+		xhdmiphy_write(inst, XHDMIPHY_TX_INIT_REG,
+			       (xhdmiphy_read(inst,
+			       XHDMIPHY_TX_INIT_REG) |
+			       XHDMIPHY_TXPCS_RESET_MASK));
+	}
+
+	xhdmiphy_mmcm_lock_en(inst, XHDMIPHY_DIR_TX, true);
+	xhdmiphy_set(inst, XHDMIPHY_CLKDET_CTRL_REG,
+		     XHDMIPHY_CLKDET_CTRL_TX_TMR_CLR_MASK);
+
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5)
+		xhdmiphy_tx_align_start(inst, XHDMIPHY_CHID_CHA, false);
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].tx_state =
+							XHDMIPHY_GT_STATE_IDLE;
+
+	/* If there is no reference clock, load TX timer in usec */
+	if (xhdmiphy_read(inst, XHDMIPHY_CLKDET_FREQ_TX_REG))
+		xhdmiphy_write(inst, XHDMIPHY_CLKDET_TMR_TX_REG,
+			       inst->conf.axilite_freq / 1000);
+}
+
+static void xhdmiphy_rx_freqchange_handler(struct xhdmiphy_dev *inst)
+{
+	enum pll_type pll_type;
+	u32 rx_refclk;
+	u8 id, id0, id1;
+
+	if (inst->rx_hdmi21_cfg.is_en)
+		if (inst->conf.rx_refclk_sel != inst->conf.rx_frl_refclk_sel)
+			return;
+
+	xhdmiphy_ch2ids(inst, XHDMIPHY_CHID_CHA, &id0, &id1);
+	for (id = id0; id <= id1; id++)
+		inst->quad.plls[XHDMIPHY_CH2IDX(id)].rx_state =
+							XHDMIPHY_GT_STATE_IDLE;
+	if (!inst->rx_hdmi21_cfg.is_en)
+		/* mask the MMCM Lock */
+		xhdmiphy_mmcm_lock_en(inst, XHDMIPHY_DIR_RX, true);
+
+	/* determine PLL type and RX reference clock selection */
+	pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+					 XHDMIPHY_CHID_CH1);
+
+	/* fetch New RX Reference Clock Frequency */
+	rx_refclk = xhdmiphy_read(inst, XHDMIPHY_CLKDET_FREQ_RX_REG);
+
+	/* round input frequency to 10 kHz */
+	rx_refclk = (rx_refclk + 5000) / 10000;
+	rx_refclk = rx_refclk * 10000;
+
+	/* store RX reference clock */
+	if (inst->rx_hdmi21_cfg.is_en)
+		inst->rx_refclk_hz = XHDMIPHY_HDMI21_FRL_REFCLK;
+	else
+		inst->rx_refclk_hz = rx_refclk;
+
+	/* If the RX frequency has changed, the PLL is always disabled */
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		xhdmiphy_powerdown_gtpll(inst, (pll_type == XHDMIPHY_PLL_CPLL) ?
+					 XHDMIPHY_CHID_CHA :
+					 XHDMIPHY_CHID_CMNA, true);
+		xhdmiphy_reset_gtpll(inst, XHDMIPHY_CHID_CHA,
+				     XHDMIPHY_DIR_RX, true);
+	} else {
+		xhdmiphy_write(inst, XHDMIPHY_RX_INIT_REG,
+			       (xhdmiphy_read(inst, XHDMIPHY_RX_INIT_REG) |
+					      XHDMIPHY_RXPCS_RESET_MASK));
+	}
+
+	/* if DRU is present, disable it and assert reset */
+	if (inst->conf.dru_present) {
+		xhdmiphy_dru_reset(inst, XHDMIPHY_CHID_CHA, true);
+		xhdmiphy_dru_en(inst, XHDMIPHY_CHID_CHA, false);
+	}
+	/* clear RX timer */
+	xhdmiphy_set(inst, XHDMIPHY_CLKDET_CTRL_REG,
+		     XHDMIPHY_CLKDET_CTRL_RX_TMR_CLR_MASK);
+	/*
+	 * If there is reference clock, load RX timer in usec.
+	 * The reference clock should be larger than 25Mhz. We are using a
+	 * 20Mhz instead to keep some margin for errors.
+	 */
+
+	if (rx_refclk > 20000000) {
+		xhdmiphy_write(inst, XHDMIPHY_CLKDET_TMR_RX_REG,
+			       inst->conf.axilite_freq / 1000);
+		if (inst->phycb[RX_INIT_CB].cb)
+			inst->phycb[RX_INIT_CB].cb(inst->phycb[RX_INIT_CB].data);
+	}
+}
+
+void xhdmiphy_gt_handler(struct xhdmiphy_dev *inst, u32 event_ack, u32 event)
+{
+	enum gt_state *tx_state;
+	enum gt_state *rx_state;
+	enum pll_type tx_pll_type;
+	enum pll_type rx_pll_type;
+
+	/* read states for Ch1 */
+	tx_state = &inst->quad.ch1.tx_state;
+	rx_state = &inst->quad.ch1.rx_state;
+
+	/* determine PLL type */
+	tx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_TX,
+					    XHDMIPHY_CHID_CH1);
+	rx_pll_type = xhdmiphy_get_pll_type(inst, XHDMIPHY_DIR_RX,
+					    XHDMIPHY_CHID_CH1);
+	if (inst->conf.gt_type != XHDMIPHY_GTYE5) {
+		if ((event & XHDMIPHY_INTR_QPLL0_LOCK_MASK) ||
+		    (event & XHDMIPHY_INTR_QPLL1_LOCK_MASK))
+			xhdmiphy_qpll_lock_handler(inst);
+
+		if (event & XHDMIPHY_INTR_CPLL_LOCK_MASK)
+			xhdmiphy_cpll_lock_handler(inst);
+
+		if ((event & XHDMIPHY_INTR_TXRESETDONE_MASK) &&
+		    (*tx_state == XHDMIPHY_GT_STATE_RESET))
+			xhdmiphy_txgt_rstdone_handler(inst);
+
+		if ((event & XHDMIPHY_INTR_TXALIGNDONE_MASK) &&
+		    (*tx_state == XHDMIPHY_GT_STATE_ALIGN))
+			xhdmiphy_txgt_aligndone_handler(inst);
+
+		if ((event & XHDMIPHY_INTR_RXRESETDONE_MASK) &&
+		    (*rx_state == XHDMIPHY_GT_STATE_RESET))
+			xhdmiphy_rxgt_rstdone_handler(inst);
+	} else {
+		if (event & XHDMIPHY_INTR_TXGPO_RE_MASK)
+			xhdmiphy_txgpo_risingedge_handler(inst);
+
+		if (event & XHDMIPHY_INTR_RXGPO_RE_MASK)
+			xhdmiphy_rxgpo_risingedge_handler(inst);
+
+		if ((event & XHDMIPHY_INTR_LCPLL_LOCK_MASK) &&
+		    (((*tx_state != XHDMIPHY_GT_STATE_IDLE) &&
+		    tx_pll_type == XHDMIPHY_PLL_LCPLL) ||
+		    ((*rx_state != XHDMIPHY_GT_STATE_IDLE) &&
+		    rx_pll_type == XHDMIPHY_PLL_LCPLL))) {
+			xhdmiphy_lcpll_lock_handler(inst);
+		}
+
+		if ((event & XHDMIPHY_INTR_RPLL_LOCK_MASK) &&
+		    (((*tx_state != XHDMIPHY_GT_STATE_IDLE) &&
+		    tx_pll_type == XHDMIPHY_PLL_RPLL) ||
+		    ((*rx_state != XHDMIPHY_GT_STATE_IDLE) &&
+		    rx_pll_type == XHDMIPHY_PLL_RPLL)))
+			xhdmiphy_rpll_lock_handler(inst);
+
+		if ((event & XHDMIPHY_INTR_TXRESETDONE_MASK) &&
+		    (*tx_state == XHDMIPHY_GT_STATE_RESET))
+			xhdmiphy_txgt_rstdone_handler(inst);
+
+		if ((event & XHDMIPHY_INTR_RXRESETDONE_MASK) &&
+		    (*rx_state == XHDMIPHY_GT_STATE_RESET))
+			xhdmiphy_rxgt_rstdone_handler(inst);
+	}
+
+	xhdmiphy_write(inst, XHDMIPHY_INTR_STS_REG, event_ack);
+}
+
+void xhdmiphy_clkdet_handler(struct xhdmiphy_dev *inst, u32 event_ack,
+			     u32 event)
+{
+	if (event & XHDMIPHY_INTR_TXFREQCHANGE_MASK)
+		xhdmiphy_tx_freqchnage_handler(inst);
+
+	if (event & XHDMIPHY_INTR_RXFREQCHANGE_MASK)
+		xhdmiphy_rx_freqchange_handler(inst);
+
+	if (event & XHDMIPHY_INTR_TXTMRTIMEOUT_MASK)
+		xhdmiphy_tx_timertimeout_handler(inst);
+
+	if (event & XHDMIPHY_INTR_RXTMRTIMEOUT_MASK)
+		xhdmiphy_rx_timertimeout_handler(inst);
+
+	xhdmiphy_write(inst, XHDMIPHY_INTR_STS_REG, event_ack);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/phy/xilinx/xilinx_dpgtquadphy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/phy/xilinx/xilinx_dpgtquadphy.c
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx GT Quad Base driver
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ *
+ * Author: Jagadeesh Banisetti <jagadeesh.banisetti@xilinx.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* Gt Quad Base Registers */
+#define GT_QUAD_BASE_CTL				0xc
+#define GT_QUAD_BASE_CTL_VALUE				0xf9e8d7c6
+#define GT_QUAD_BASE_CH1_CLK_DIV_REG			0x3694
+#define GT_QUAD_BASE_CH1_CLK_DIV_MASK			GENMASK(9, 0)
+#define GT_QUAD_BASE_CH1_CLK_DIV_VALUE			0x260
+#define GT_QUAD_BASE_DEFAULT_VAL			0
+
+struct dpgtquadphy_dev {
+	struct phy *phy;
+	struct clk *axi_clk;
+	void __iomem *base;
+};
+
+static int xdpgtquad_init(struct phy *phy)
+{
+	struct dpgtquadphy_dev *gtquad = phy_get_drvdata(phy);
+	u32 data;
+
+	/*
+	 * Unlocking the NPI space so that GT CH1 divider value can be
+	 * programmed. This will generate a /20 clk
+	 */
+	writel(GT_QUAD_BASE_CTL_VALUE,
+	       gtquad->base + GT_QUAD_BASE_CTL);
+
+	data = readl(gtquad->base + GT_QUAD_BASE_CH1_CLK_DIV_REG);
+	data &= ~GT_QUAD_BASE_CH1_CLK_DIV_MASK;
+	data |= FIELD_PREP(GT_QUAD_BASE_CH1_CLK_DIV_MASK,
+			   GT_QUAD_BASE_CH1_CLK_DIV_VALUE);
+	writel(data, gtquad->base + GT_QUAD_BASE_CH1_CLK_DIV_REG);
+
+	return 0;
+}
+
+static int xdpgtquad_reset(struct phy *phy)
+{
+	struct dpgtquadphy_dev *gtquad = phy_get_drvdata(phy);
+
+	writel(GT_QUAD_BASE_DEFAULT_VAL,
+	       gtquad->base + GT_QUAD_BASE_CTL);
+	writel(GT_QUAD_BASE_DEFAULT_VAL,
+	       gtquad->base + GT_QUAD_BASE_CH1_CLK_DIV_REG);
+
+	return 0;
+}
+
+static struct phy *xdpgtquadphy_xlate(struct device *dev,
+				      struct of_phandle_args *args)
+{
+	struct dpgtquadphy_dev *priv = dev_get_drvdata(dev);
+	struct device_node *gtquadphynode = args->np;
+
+	if (!of_device_is_available(gtquadphynode)) {
+		dev_warn(dev, "requested PHY is disabled\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	return priv->phy;
+}
+
+static const struct phy_ops xdpgtquad_phyops = {
+	.reset		= xdpgtquad_reset,
+	.init		= xdpgtquad_init,
+	.owner		= THIS_MODULE,
+};
+
+/**
+ * gt_quad_probe - The device probe function for driver initialization.
+ * @pdev: pointer to the platform device structure.
+ *
+ * Return: 0 for success and error value on failure
+ */
+static int gt_quad_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct dpgtquadphy_dev *gtquad;
+	struct phy *phy;
+	struct phy_provider *provider;
+	struct resource *res;
+	int ret;
+
+	gtquad = devm_kzalloc(&pdev->dev, sizeof(*gtquad), GFP_KERNEL);
+	if (!gtquad)
+		return -ENOMEM;
+
+	gtquad->axi_clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(gtquad->axi_clk)) {
+		dev_err(&pdev->dev, "failed to get s_axi_clk\n");
+		return PTR_ERR(gtquad->axi_clk);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	gtquad->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(gtquad->base)) {
+		dev_err(&pdev->dev, "Couldn't map GT Quad Base IP registers\n");
+		return PTR_ERR(gtquad->base);
+	}
+
+	ret = clk_prepare_enable(gtquad->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable axi_clk (%d)\n", ret);
+		return ret;
+	}
+
+	phy = devm_phy_create(&pdev->dev, np, &xdpgtquad_phyops);
+	if (IS_ERR(phy)) {
+		dev_err(&pdev->dev, "failed to create DP GT_QUAD PHY\n");
+		ret = PTR_ERR(phy);
+		goto error_clk;
+	}
+	gtquad->phy = phy;
+	phy_set_drvdata(phy, gtquad);
+
+	provider = devm_of_phy_provider_register(&pdev->dev, xdpgtquadphy_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(&pdev->dev, "registering provider failed\n");
+		ret = PTR_ERR(provider);
+		goto error_clk;
+	}
+
+	platform_set_drvdata(pdev, gtquad);
+
+	return 0;
+
+error_clk:
+	clk_disable_unprepare(gtquad->axi_clk);
+
+	return ret;
+}
+
+static int gt_quad_remove(struct platform_device *pdev)
+{
+	struct dpgtquadphy_dev *gtquad = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(gtquad->axi_clk);
+
+	return 0;
+}
+
+/* Match table for of_platform binding */
+static const struct of_device_id dpgtquadphy_of_match[] = {
+	{ .compatible = "xlnx,gt-quad-base-1.1" },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, dpgtquadphy_of_match);
+
+static struct platform_driver dpgtquadphy_driver = {
+	.probe = gt_quad_probe,
+	.remove = gt_quad_remove,
+	.driver = {
+		.name = "xilinx-dpgtquadphy",
+		.of_match_table	= dpgtquadphy_of_match,
+	},
+};
+module_platform_driver(dpgtquadphy_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Jagadeesh Banisetti <jbaniset@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx driver for GT Quad Base");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/aspeed/pinctrl-aspeed-g6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/aspeed/pinctrl-aspeed-g6.c
@@ -43,7 +43,7 @@
 #define SCU614		0x614 /* Disable GPIO Internal Pull-Down #1 */
 #define SCU618		0x618 /* Disable GPIO Internal Pull-Down #2 */
 #define SCU61C		0x61c /* Disable GPIO Internal Pull-Down #3 */
-#define SCU620		0x620 /* Disable GPIO Internal Pull-Down #4 */
+#define SCU630		0x630 /* Disable GPIO Internal Pull-Down #4 */
 #define SCU634		0x634 /* Disable GPIO Internal Pull-Down #5 */
 #define SCU638		0x638 /* Disable GPIO Internal Pull-Down #6 */
 #define SCU690		0x690 /* Multi-function Pin Control #24 */
@@ -1236,18 +1236,12 @@
 FUNC_GROUP_DECL(WDTRST4, AA12);
 
 #define AE12 196
-SIG_EXPR_LIST_DECL_SEMG(AE12, FWSPIDQ2, FWQSPID, FWSPID,
-			SIG_DESC_SET(SCU438, 4));
 SIG_EXPR_LIST_DECL_SESG(AE12, GPIOY4, GPIOY4);
-PIN_DECL_(AE12, SIG_EXPR_LIST_PTR(AE12, FWSPIDQ2),
-	  SIG_EXPR_LIST_PTR(AE12, GPIOY4));
+PIN_DECL_(AE12, SIG_EXPR_LIST_PTR(AE12, GPIOY4));
 
 #define AF12 197
-SIG_EXPR_LIST_DECL_SEMG(AF12, FWSPIDQ3, FWQSPID, FWSPID,
-			SIG_DESC_SET(SCU438, 5));
 SIG_EXPR_LIST_DECL_SESG(AF12, GPIOY5, GPIOY5);
-PIN_DECL_(AF12, SIG_EXPR_LIST_PTR(AF12, FWSPIDQ3),
-	  SIG_EXPR_LIST_PTR(AF12, GPIOY5));
+PIN_DECL_(AF12, SIG_EXPR_LIST_PTR(AF12, GPIOY5));
 
 #define AC12 198
 SSSF_PIN_DECL(AC12, GPIOY6, FWSPIABR, SIG_DESC_SET(SCU438, 6));
@@ -1520,9 +1514,8 @@
 PIN_DECL_3(Y4, GPIO18E3, FWSPIDMISO, VBMISO, EMMCDAT7);
 
 GROUP_DECL(FWSPID, Y1, Y2, Y3, Y4);
-GROUP_DECL(FWQSPID, Y1, Y2, Y3, Y4, AE12, AF12);
 GROUP_DECL(EMMCG8, AB4, AA4, AC4, AA5, Y5, AB5, AB6, AC5, Y1, Y2, Y3, Y4);
-FUNC_DECL_2(FWSPID, FWSPID, FWQSPID);
+FUNC_DECL_1(FWSPID, FWSPID);
 FUNC_GROUP_DECL(VB, Y1, Y2, Y3, Y4);
 FUNC_DECL_3(EMMC, EMMCG1, EMMCG4, EMMCG8);
 /*
@@ -1918,7 +1911,6 @@
 	ASPEED_PINCTRL_GROUP(FSI2),
 	ASPEED_PINCTRL_GROUP(FWSPIABR),
 	ASPEED_PINCTRL_GROUP(FWSPID),
-	ASPEED_PINCTRL_GROUP(FWQSPID),
 	ASPEED_PINCTRL_GROUP(FWSPIWP),
 	ASPEED_PINCTRL_GROUP(GPIT0),
 	ASPEED_PINCTRL_GROUP(GPIT1),
@@ -2495,38 +2487,38 @@
 	ASPEED_PULL_DOWN_PINCONF(D14, SCU61C, 0),
 
 	/* GPIOS7 */
-	ASPEED_PULL_DOWN_PINCONF(T24, SCU620, 23),
+	ASPEED_PULL_DOWN_PINCONF(T24, SCU630, 23),
 	/* GPIOS6 */
-	ASPEED_PULL_DOWN_PINCONF(P23, SCU620, 22),
+	ASPEED_PULL_DOWN_PINCONF(P23, SCU630, 22),
 	/* GPIOS5 */
-	ASPEED_PULL_DOWN_PINCONF(P24, SCU620, 21),
+	ASPEED_PULL_DOWN_PINCONF(P24, SCU630, 21),
 	/* GPIOS4 */
-	ASPEED_PULL_DOWN_PINCONF(R26, SCU620, 20),
+	ASPEED_PULL_DOWN_PINCONF(R26, SCU630, 20),
 	/* GPIOS3*/
-	ASPEED_PULL_DOWN_PINCONF(R24, SCU620, 19),
+	ASPEED_PULL_DOWN_PINCONF(R24, SCU630, 19),
 	/* GPIOS2 */
-	ASPEED_PULL_DOWN_PINCONF(T26, SCU620, 18),
+	ASPEED_PULL_DOWN_PINCONF(T26, SCU630, 18),
 	/* GPIOS1 */
-	ASPEED_PULL_DOWN_PINCONF(T25, SCU620, 17),
+	ASPEED_PULL_DOWN_PINCONF(T25, SCU630, 17),
 	/* GPIOS0 */
-	ASPEED_PULL_DOWN_PINCONF(R23, SCU620, 16),
+	ASPEED_PULL_DOWN_PINCONF(R23, SCU630, 16),
 
 	/* GPIOR7 */
-	ASPEED_PULL_DOWN_PINCONF(U26, SCU620, 15),
+	ASPEED_PULL_DOWN_PINCONF(U26, SCU630, 15),
 	/* GPIOR6 */
-	ASPEED_PULL_DOWN_PINCONF(W26, SCU620, 14),
+	ASPEED_PULL_DOWN_PINCONF(W26, SCU630, 14),
 	/* GPIOR5 */
-	ASPEED_PULL_DOWN_PINCONF(T23, SCU620, 13),
+	ASPEED_PULL_DOWN_PINCONF(T23, SCU630, 13),
 	/* GPIOR4 */
-	ASPEED_PULL_DOWN_PINCONF(U25, SCU620, 12),
+	ASPEED_PULL_DOWN_PINCONF(U25, SCU630, 12),
 	/* GPIOR3*/
-	ASPEED_PULL_DOWN_PINCONF(V26, SCU620, 11),
+	ASPEED_PULL_DOWN_PINCONF(V26, SCU630, 11),
 	/* GPIOR2 */
-	ASPEED_PULL_DOWN_PINCONF(V24, SCU620, 10),
+	ASPEED_PULL_DOWN_PINCONF(V24, SCU630, 10),
 	/* GPIOR1 */
-	ASPEED_PULL_DOWN_PINCONF(U24, SCU620, 9),
+	ASPEED_PULL_DOWN_PINCONF(U24, SCU630, 9),
 	/* GPIOR0 */
-	ASPEED_PULL_DOWN_PINCONF(V25, SCU620, 8),
+	ASPEED_PULL_DOWN_PINCONF(V25, SCU630, 8),
 
 	/* GPIOX7 */
 	ASPEED_PULL_DOWN_PINCONF(AB10, SCU634, 31),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/aspeed/pinctrl-aspeed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/aspeed/pinctrl-aspeed.c
@@ -122,7 +122,7 @@
 	int ret = 0;
 
 	if (!exprs)
-		return true;
+		return -EINVAL;
 
 	while (*exprs && !ret) {
 		ret = aspeed_sig_expr_disable(ctx, *exprs);
@@ -236,11 +236,11 @@
 		const struct aspeed_sig_expr **funcs;
 		const struct aspeed_sig_expr ***prios;
 
-		pr_debug("Muxing pin %s for %s\n", pdesc->name, pfunc->name);
-
 		if (!pdesc)
 			return -EINVAL;
 
+		pr_debug("Muxing pin %s for %s\n", pdesc->name, pfunc->name);
+
 		prios = pdesc->prios;
 
 		if (!prios)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/bcm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/bcm/Kconfig
@@ -35,6 +35,7 @@
 	select PINCONF
 	select GENERIC_PINCONF
 	select GPIOLIB
+	select REGMAP
 	select GPIO_REGMAP
 
 config PINCTRL_BCM6318
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/bcm/pinctrl-bcm281xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/bcm/pinctrl-bcm281xx.c
@@ -981,7 +981,7 @@
 	.reg_bits = 32,
 	.reg_stride = 4,
 	.val_bits = 32,
-	.max_register = BCM281XX_PIN_VC_CAM3_SDA,
+	.max_register = BCM281XX_PIN_VC_CAM3_SDA * 4,
 };
 
 static int bcm281xx_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -351,6 +351,18 @@
 	return pinctrl_gpio_direction_output(chip->base + offset);
 }
 
+static int bcm2835_of_gpio_ranges_fallback(struct gpio_chip *gc,
+					   struct device_node *np)
+{
+	struct pinctrl_dev *pctldev = of_pinctrl_get(np);
+
+	if (!pctldev)
+		return 0;
+
+	return gpiochip_add_pin_range(gc, pinctrl_dev_get_devname(pctldev), 0, 0,
+				      gc->ngpio);
+}
+
 static const struct gpio_chip bcm2835_gpio_chip = {
 	.label = MODULE_NAME,
 	.owner = THIS_MODULE,
@@ -365,6 +377,7 @@
 	.base = -1,
 	.ngpio = BCM2835_NUM_GPIOS,
 	.can_sleep = false,
+	.of_gpio_ranges_fallback = bcm2835_of_gpio_ranges_fallback,
 };
 
 static const struct gpio_chip bcm2711_gpio_chip = {
@@ -381,6 +394,7 @@
 	.base = -1,
 	.ngpio = BCM2711_NUM_GPIOS,
 	.can_sleep = false,
+	.of_gpio_ranges_fallback = bcm2835_of_gpio_ranges_fallback,
 };
 
 static void bcm2835_gpio_irq_handle_bank(struct bcm2835_pinctrl *pc,
@@ -1243,6 +1257,18 @@
 		raw_spin_lock_init(&pc->irq_lock[i]);
 	}
 
+	pc->pctl_desc = *pdata->pctl_desc;
+	pc->pctl_dev = devm_pinctrl_register(dev, &pc->pctl_desc, pc);
+	if (IS_ERR(pc->pctl_dev)) {
+		gpiochip_remove(&pc->gpio_chip);
+		return PTR_ERR(pc->pctl_dev);
+	}
+
+	pc->gpio_range = *pdata->gpio_range;
+	pc->gpio_range.base = pc->gpio_chip.base;
+	pc->gpio_range.gc = &pc->gpio_chip;
+	pinctrl_add_gpio_range(pc->pctl_dev, &pc->gpio_range);
+
 	girq = &pc->gpio_chip.irq;
 	girq->chip = &bcm2835_gpio_irq_chip;
 	girq->parent_handler = bcm2835_gpio_irq_handler;
@@ -1250,15 +1276,19 @@
 	girq->parents = devm_kcalloc(dev, BCM2835_NUM_IRQS,
 				     sizeof(*girq->parents),
 				     GFP_KERNEL);
-	if (!girq->parents)
-		return -ENOMEM;
+	if (!girq->parents) {
+		err = -ENOMEM;
+		goto out_remove;
+	}
 
 	if (is_7211) {
 		pc->wake_irq = devm_kcalloc(dev, BCM2835_NUM_IRQS,
 					    sizeof(*pc->wake_irq),
 					    GFP_KERNEL);
-		if (!pc->wake_irq)
-			return -ENOMEM;
+		if (!pc->wake_irq) {
+			err = -ENOMEM;
+			goto out_remove;
+		}
 	}
 
 	/*
@@ -1286,8 +1316,10 @@
 
 		len = strlen(dev_name(pc->dev)) + 16;
 		name = devm_kzalloc(pc->dev, len, GFP_KERNEL);
-		if (!name)
-			return -ENOMEM;
+		if (!name) {
+			err = -ENOMEM;
+			goto out_remove;
+		}
 
 		snprintf(name, len, "%s:bank%d", dev_name(pc->dev), i);
 
@@ -1306,22 +1338,14 @@
 	err = gpiochip_add_data(&pc->gpio_chip, pc);
 	if (err) {
 		dev_err(dev, "could not add GPIO chip\n");
-		return err;
-	}
-
-	pc->pctl_desc = *pdata->pctl_desc;
-	pc->pctl_dev = devm_pinctrl_register(dev, &pc->pctl_desc, pc);
-	if (IS_ERR(pc->pctl_dev)) {
-		gpiochip_remove(&pc->gpio_chip);
-		return PTR_ERR(pc->pctl_dev);
+		goto out_remove;
 	}
 
-	pc->gpio_range = *pdata->gpio_range;
-	pc->gpio_range.base = pc->gpio_chip.base;
-	pc->gpio_range.gc = &pc->gpio_chip;
-	pinctrl_add_gpio_range(pc->pctl_dev, &pc->gpio_range);
-
 	return 0;
+
+out_remove:
+	pinctrl_remove_gpio_range(pc->pctl_dev, &pc->gpio_range);
+	return err;
 }
 
 static struct platform_driver bcm2835_pinctrl_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/cirrus/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/cirrus/Kconfig
@@ -1,7 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config PINCTRL_LOCHNAGAR
 	tristate "Cirrus Logic Lochnagar pinctrl driver"
-	depends on MFD_LOCHNAGAR
+	# Avoid clash caused by MIPS defining RST, which is used in the driver
+	depends on MFD_LOCHNAGAR && !MIPS
 	select GPIOLIB
 	select PINMUX
 	select PINCONF
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/core.c
@@ -205,6 +205,7 @@
 				    const struct pinctrl_pin_desc *pin)
 {
 	struct pin_desc *pindesc;
+	int error;
 
 	pindesc = pin_desc_get(pctldev, pin->number);
 	if (pindesc) {
@@ -226,18 +227,25 @@
 	} else {
 		pindesc->name = kasprintf(GFP_KERNEL, "PIN%u", pin->number);
 		if (!pindesc->name) {
-			kfree(pindesc);
-			return -ENOMEM;
+			error = -ENOMEM;
+			goto failed;
 		}
 		pindesc->dynamic_name = true;
 	}
 
 	pindesc->drv_data = pin->drv_data;
 
-	radix_tree_insert(&pctldev->pin_desc_tree, pin->number, pindesc);
+	error = radix_tree_insert(&pctldev->pin_desc_tree, pin->number, pindesc);
+	if (error)
+		goto failed;
+
 	pr_debug("registered pin %d (%s) on %s\n",
 		 pin->number, pindesc->name, pctldev->desc->name);
 	return 0;
+
+failed:
+	kfree(pindesc);
+	return error;
 }
 
 static int pinctrl_register_pins(struct pinctrl_dev *pctldev,
@@ -1084,8 +1092,8 @@
 		 * an -EPROBE_DEFER later, as that is the worst case.
 		 */
 		if (ret == -EPROBE_DEFER) {
-			pinctrl_free(p, false);
 			mutex_unlock(&pinctrl_maps_mutex);
+			pinctrl_free(p, false);
 			return ERR_PTR(ret);
 		}
 	}
@@ -1239,17 +1247,17 @@
 static int pinctrl_commit_state(struct pinctrl *p, struct pinctrl_state *state)
 {
 	struct pinctrl_setting *setting, *setting2;
-	struct pinctrl_state *old_state = p->state;
+	struct pinctrl_state *old_state = READ_ONCE(p->state);
 	int ret;
 
-	if (p->state) {
+	if (old_state) {
 		/*
 		 * For each pinmux setting in the old state, forget SW's record
 		 * of mux owner for that pingroup. Any pingroups which are
 		 * still owned by the new state will be re-acquired by the call
 		 * to pinmux_enable_setting() in the loop below.
 		 */
-		list_for_each_entry(setting, &p->state->settings, node) {
+		list_for_each_entry(setting, &old_state->settings, node) {
 			if (setting->type != PIN_MAP_TYPE_MUX_GROUP)
 				continue;
 			pinmux_disable_setting(setting);
@@ -2054,6 +2062,14 @@
 	return ERR_PTR(ret);
 }
 
+static void pinctrl_uninit_controller(struct pinctrl_dev *pctldev, struct pinctrl_desc *pctldesc)
+{
+	pinctrl_free_pindescs(pctldev, pctldesc->pins,
+			      pctldesc->npins);
+	mutex_destroy(&pctldev->mutex);
+	kfree(pctldev);
+}
+
 static int pinctrl_claim_hogs(struct pinctrl_dev *pctldev)
 {
 	pctldev->p = create_pinctrl(pctldev->dev, pctldev);
@@ -2098,11 +2114,7 @@
 
 	error = pinctrl_claim_hogs(pctldev);
 	if (error) {
-		dev_err(pctldev->dev, "could not claim hogs: %i\n",
-			error);
-		mutex_destroy(&pctldev->mutex);
-		kfree(pctldev);
-
+		dev_err(pctldev->dev, "could not claim hogs: %i\n", error);
 		return error;
 	}
 
@@ -2138,8 +2150,10 @@
 		return pctldev;
 
 	error = pinctrl_enable(pctldev);
-	if (error)
+	if (error) {
+		pinctrl_uninit_controller(pctldev, pctldesc);
 		return ERR_PTR(error);
+	}
 
 	return pctldev;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/devicetree.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/devicetree.c
@@ -220,12 +220,16 @@
 	for (state = 0; ; state++) {
 		/* Retrieve the pinctrl-* property */
 		propname = kasprintf(GFP_KERNEL, "pinctrl-%d", state);
+		if (!propname) {
+			ret = -ENOMEM;
+			goto err;
+		}
 		prop = of_find_property(np, propname, &size);
 		kfree(propname);
 		if (!prop) {
 			if (state == 0) {
-				of_node_put(np);
-				return -ENODEV;
+				ret = -ENODEV;
+				goto err;
 			}
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/freescale/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/freescale/Kconfig
@@ -9,7 +9,7 @@
 
 config PINCTRL_IMX_SCU
 	tristate
-	depends on IMX_SCU
+	depends on IMX_SCU || COMPILE_TEST
 	select PINCTRL_IMX
 
 config PINCTRL_IMX1_CORE
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/freescale/pinctrl-mxs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/freescale/pinctrl-mxs.c
@@ -405,8 +405,8 @@
 	int ret;
 	u32 val;
 
-	child = of_get_next_child(np, NULL);
-	if (!child) {
+	val = of_get_child_count(np);
+	if (val == 0) {
 		dev_err(&pdev->dev, "no group is defined\n");
 		return -ENOENT;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/intel/pinctrl-cherryview.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/intel/pinctrl-cherryview.c
@@ -945,11 +945,6 @@
 
 		break;
 
-	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
-		if (!(ctrl1 & CHV_PADCTRL1_ODEN))
-			return -EINVAL;
-		break;
-
 	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: {
 		u32 cfg;
 
@@ -959,6 +954,16 @@
 			return -EINVAL;
 
 		break;
+
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		if (ctrl1 & CHV_PADCTRL1_ODEN)
+			return -EINVAL;
+		break;
+
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		if (!(ctrl1 & CHV_PADCTRL1_ODEN))
+			return -EINVAL;
+		break;
 	}
 
 	default:
@@ -1619,7 +1624,6 @@
 	const struct intel_pinctrl_soc_data *soc_data;
 	struct intel_community *community;
 	struct device *dev = &pdev->dev;
-	struct acpi_device *adev = ACPI_COMPANION(dev);
 	struct intel_pinctrl *pctrl;
 	acpi_status status;
 	int ret, irq;
@@ -1682,7 +1686,7 @@
 	if (ret)
 		return ret;
 
-	status = acpi_install_address_space_handler(adev->handle,
+	status = acpi_install_address_space_handler(ACPI_HANDLE(dev),
 					community->acpi_space_id,
 					chv_pinctrl_mmio_access_handler,
 					NULL, pctrl);
@@ -1699,7 +1703,7 @@
 	struct intel_pinctrl *pctrl = platform_get_drvdata(pdev);
 	const struct intel_community *community = &pctrl->communities[0];
 
-	acpi_remove_address_space_handler(ACPI_COMPANION(&pdev->dev),
+	acpi_remove_address_space_handler(ACPI_HANDLE(&pdev->dev),
 					  community->acpi_space_id,
 					  chv_pinctrl_mmio_access_handler);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/intel/pinctrl-intel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/intel/pinctrl-intel.c
@@ -436,9 +436,14 @@
 	writel(value, padcfg0);
 }
 
+static int __intel_gpio_get_gpio_mode(u32 value)
+{
+	return (value & PADCFG0_PMODE_MASK) >> PADCFG0_PMODE_SHIFT;
+}
+
 static int intel_gpio_get_gpio_mode(void __iomem *padcfg0)
 {
-	return (readl(padcfg0) & PADCFG0_PMODE_MASK) >> PADCFG0_PMODE_SHIFT;
+	return __intel_gpio_get_gpio_mode(readl(padcfg0));
 }
 
 static void intel_gpio_set_gpio_mode(void __iomem *padcfg0)
@@ -451,8 +456,8 @@
 	value &= ~PADCFG0_PMODE_MASK;
 	value |= PADCFG0_PMODE_GPIO;
 
-	/* Disable input and output buffers */
-	value |= PADCFG0_GPIORXDIS;
+	/* Disable TX buffer and enable RX (this will be input) */
+	value &= ~PADCFG0_GPIORXDIS;
 	value |= PADCFG0_GPIOTXDIS;
 
 	/* Disable SCI/SMI/NMI generation */
@@ -497,9 +502,6 @@
 
 	intel_gpio_set_gpio_mode(padcfg0);
 
-	/* Disable TX buffer and enable RX (this will be input) */
-	__intel_gpio_set_direction(padcfg0, true);
-
 	raw_spin_unlock_irqrestore(&pctrl->lock, flags);
 
 	return 0;
@@ -1115,9 +1117,6 @@
 
 	intel_gpio_set_gpio_mode(reg);
 
-	/* Disable TX buffer and enable RX (this will be input) */
-	__intel_gpio_set_direction(reg, true);
-
 	value = readl(reg);
 
 	value &= ~(PADCFG0_RXEVCFG_MASK | PADCFG0_RXINV);
@@ -1216,6 +1215,39 @@
 	return IRQ_RETVAL(ret);
 }
 
+static void intel_gpio_irq_init(struct intel_pinctrl *pctrl)
+{
+	int i;
+
+	for (i = 0; i < pctrl->ncommunities; i++) {
+		const struct intel_community *community;
+		void __iomem *base;
+		unsigned int gpp;
+
+		community = &pctrl->communities[i];
+		base = community->regs;
+
+		for (gpp = 0; gpp < community->ngpps; gpp++) {
+			/* Mask and clear all interrupts */
+			writel(0, base + community->ie_offset + gpp * 4);
+			writel(0xffff, base + community->is_offset + gpp * 4);
+		}
+	}
+}
+
+static int intel_gpio_irq_init_hw(struct gpio_chip *gc)
+{
+	struct intel_pinctrl *pctrl = gpiochip_get_data(gc);
+
+	/*
+	 * Make sure the interrupt lines are in a proper state before
+	 * further configuration.
+	 */
+	intel_gpio_irq_init(pctrl);
+
+	return 0;
+}
+
 static int intel_gpio_add_community_ranges(struct intel_pinctrl *pctrl,
 				const struct intel_community *community)
 {
@@ -1320,6 +1352,7 @@
 	girq->num_parents = 0;
 	girq->default_type = IRQ_TYPE_NONE;
 	girq->handler = handle_bad_irq;
+	girq->init_hw = intel_gpio_irq_init_hw;
 
 	ret = devm_gpiochip_add_data(pctrl->dev, &pctrl->chip, pctrl);
 	if (ret) {
@@ -1598,16 +1631,14 @@
 
 const struct intel_pinctrl_soc_data *intel_pinctrl_get_soc_data(struct platform_device *pdev)
 {
+	const struct intel_pinctrl_soc_data * const *table;
 	const struct intel_pinctrl_soc_data *data = NULL;
-	const struct intel_pinctrl_soc_data **table;
-	struct acpi_device *adev;
-	unsigned int i;
 
-	adev = ACPI_COMPANION(&pdev->dev);
-	if (adev) {
-		const void *match = device_get_match_data(&pdev->dev);
+	table = device_get_match_data(&pdev->dev);
+	if (table) {
+		struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+		unsigned int i;
 
-		table = (const struct intel_pinctrl_soc_data **)match;
 		for (i = 0; table[i]; i++) {
 			if (!strcmp(adev->pnp.unique_id, table[i]->uid)) {
 				data = table[i];
@@ -1621,7 +1652,7 @@
 		if (!id)
 			return ERR_PTR(-ENODEV);
 
-		table = (const struct intel_pinctrl_soc_data **)id->driver_data;
+		table = (const struct intel_pinctrl_soc_data * const *)id->driver_data;
 		data = table[pdev->id];
 	}
 
@@ -1630,9 +1661,16 @@
 EXPORT_SYMBOL_GPL(intel_pinctrl_get_soc_data);
 
 #ifdef CONFIG_PM_SLEEP
+static bool __intel_gpio_is_direct_irq(u32 value)
+{
+	return (value & PADCFG0_GPIROUTIOXAPIC) && (value & PADCFG0_GPIOTXDIS) &&
+	       (__intel_gpio_get_gpio_mode(value) == PADCFG0_PMODE_GPIO);
+}
+
 static bool intel_pinctrl_should_save(struct intel_pinctrl *pctrl, unsigned int pin)
 {
 	const struct pin_desc *pd = pin_desc_get(pctrl->pctldev, pin);
+	u32 value;
 
 	if (!pd || !intel_pad_usable(pctrl, pin))
 		return false;
@@ -1647,6 +1685,24 @@
 	    gpiochip_line_is_irq(&pctrl->chip, intel_pin_to_gpio(pctrl, pin)))
 		return true;
 
+	/*
+	 * The firmware on some systems may configure GPIO pins to be
+	 * an interrupt source in so called "direct IRQ" mode. In such
+	 * cases the GPIO controller driver has no idea if those pins
+	 * are being used or not. At the same time, there is a known bug
+	 * in the firmwares that don't restore the pin settings correctly
+	 * after suspend, i.e. by an unknown reason the Rx value becomes
+	 * inverted.
+	 *
+	 * Hence, let's save and restore the pins that are configured
+	 * as GPIOs in the input mode with GPIROUTIOXAPIC bit set.
+	 *
+	 * See https://bugzilla.kernel.org/show_bug.cgi?id=214749.
+	 */
+	value = readl(intel_get_padcfg(pctrl, pin, PADCFG0));
+	if (__intel_gpio_is_direct_irq(value))
+		return true;
+
 	return false;
 }
 
@@ -1695,26 +1751,6 @@
 }
 EXPORT_SYMBOL_GPL(intel_pinctrl_suspend_noirq);
 
-static void intel_gpio_irq_init(struct intel_pinctrl *pctrl)
-{
-	size_t i;
-
-	for (i = 0; i < pctrl->ncommunities; i++) {
-		const struct intel_community *community;
-		void __iomem *base;
-		unsigned int gpp;
-
-		community = &pctrl->communities[i];
-		base = community->regs;
-
-		for (gpp = 0; gpp < community->ngpps; gpp++) {
-			/* Mask and clear all interrupts */
-			writel(0, base + community->ie_offset + gpp * 4);
-			writel(0xffff, base + community->is_offset + gpp * 4);
-		}
-	}
-}
-
 static bool intel_gpio_update_reg(void __iomem *reg, u32 mask, u32 value)
 {
 	u32 curr, updated;
@@ -1794,7 +1830,12 @@
 	for (i = 0; i < pctrl->soc->npins; i++) {
 		const struct pinctrl_pin_desc *desc = &pctrl->soc->pins[i];
 
-		if (!intel_pinctrl_should_save(pctrl, desc->number))
+		if (!(intel_pinctrl_should_save(pctrl, desc->number) ||
+		      /*
+		       * If the firmware mangled the register contents too much,
+		       * check the saved value for the Direct IRQ mode.
+		       */
+		      __intel_gpio_is_direct_irq(pads[i].padcfg0)))
 			continue;
 
 		intel_restore_padcfg(pctrl, desc->number, PADCFG0, pads[i].padcfg0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/intel/pinctrl-tigerlake.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/intel/pinctrl-tigerlake.c
@@ -749,7 +749,6 @@
 	{ "INT34C5", (kernel_ulong_t)&tgllp_soc_data },
 	{ "INT34C6", (kernel_ulong_t)&tglh_soc_data },
 	{ "INTC1055", (kernel_ulong_t)&tgllp_soc_data },
-	{ "INTC1057", (kernel_ulong_t)&tgllp_soc_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, tgl_pinctrl_acpi_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/Kconfig
@@ -30,6 +30,7 @@
 	select GENERIC_PINMUX_FUNCTIONS
 	select GPIOLIB
 	select OF_GPIO
+	select EINT_MTK
 	select PINCTRL_MTK_V2
 
 config PINCTRL_MTK_PARIS
@@ -151,6 +152,7 @@
 	bool "Mediatek MT8195 pin control"
 	depends on OF
 	depends on ARM64 || COMPILE_TEST
+	default ARM64 && ARCH_MEDIATEK
 	select PINCTRL_MTK_PARIS
 
 config PINCTRL_MT8365
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/mtk-eint.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/mtk-eint.c
@@ -287,12 +287,15 @@
 
 static unsigned int mtk_eint_hw_init(struct mtk_eint *eint)
 {
-	void __iomem *reg = eint->base + eint->regs->dom_en;
+	void __iomem *dom_en = eint->base + eint->regs->dom_en;
+	void __iomem *mask_set = eint->base + eint->regs->mask_set;
 	unsigned int i;
 
 	for (i = 0; i < eint->hw->ap_num; i += 32) {
-		writel(0xffffffff, reg);
-		reg += 4;
+		writel(0xffffffff, dom_en);
+		writel(0xffffffff, mask_set);
+		dom_en += 4;
+		mask_set += 4;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/pinctrl-mt8192.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/pinctrl-mt8192.c
@@ -1346,7 +1346,6 @@
 	[PINCTRL_PIN_REG_DIR] = MTK_RANGE(mt8192_pin_dir_range),
 	[PINCTRL_PIN_REG_DI] = MTK_RANGE(mt8192_pin_di_range),
 	[PINCTRL_PIN_REG_DO] = MTK_RANGE(mt8192_pin_do_range),
-	[PINCTRL_PIN_REG_SR] = MTK_RANGE(mt8192_pin_dir_range),
 	[PINCTRL_PIN_REG_SMT] = MTK_RANGE(mt8192_pin_smt_range),
 	[PINCTRL_PIN_REG_IES] = MTK_RANGE(mt8192_pin_ies_range),
 	[PINCTRL_PIN_REG_PU] = MTK_RANGE(mt8192_pin_pu_range),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/pinctrl-mt8195.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/pinctrl-mt8195.c
@@ -659,7 +659,7 @@
 	PIN_FIELD_BASE(10, 10, 4, 0x010, 0x10, 9, 3),
 	PIN_FIELD_BASE(11, 11, 4, 0x000, 0x10, 24, 3),
 	PIN_FIELD_BASE(12, 12, 4, 0x010, 0x10, 12, 3),
-	PIN_FIELD_BASE(13, 13, 4, 0x010, 0x10, 27, 3),
+	PIN_FIELD_BASE(13, 13, 4, 0x000, 0x10, 27, 3),
 	PIN_FIELD_BASE(14, 14, 4, 0x010, 0x10, 15, 3),
 	PIN_FIELD_BASE(15, 15, 4, 0x010, 0x10, 0, 3),
 	PIN_FIELD_BASE(16, 16, 4, 0x010, 0x10, 18, 3),
@@ -708,7 +708,7 @@
 	PIN_FIELD_BASE(78, 78, 3, 0x000, 0x10, 15, 3),
 	PIN_FIELD_BASE(79, 79, 3, 0x000, 0x10, 18, 3),
 	PIN_FIELD_BASE(80, 80, 3, 0x000, 0x10, 21, 3),
-	PIN_FIELD_BASE(81, 81, 3, 0x000, 0x10, 28, 3),
+	PIN_FIELD_BASE(81, 81, 3, 0x000, 0x10, 24, 3),
 	PIN_FIELD_BASE(82, 82, 3, 0x000, 0x10, 27, 3),
 	PIN_FIELD_BASE(83, 83, 3, 0x010, 0x10, 0, 3),
 	PIN_FIELD_BASE(84, 84, 3, 0x010, 0x10, 3, 3),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/pinctrl-mt8365.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/pinctrl-mt8365.c
@@ -259,7 +259,7 @@
 	MTK_PIN_IES_SMT_SPEC(104, 104, 0x420, 13),
 	MTK_PIN_IES_SMT_SPEC(105, 109, 0x420, 14),
 	MTK_PIN_IES_SMT_SPEC(110, 113, 0x420, 15),
-	MTK_PIN_IES_SMT_SPEC(114, 112, 0x420, 16),
+	MTK_PIN_IES_SMT_SPEC(114, 116, 0x420, 16),
 	MTK_PIN_IES_SMT_SPEC(117, 119, 0x420, 17),
 	MTK_PIN_IES_SMT_SPEC(120, 122, 0x420, 18),
 	MTK_PIN_IES_SMT_SPEC(123, 125, 0x420, 19),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c
@@ -285,8 +285,12 @@
 	desc = (const struct mtk_pin_desc *)hw->soc->pins;
 	*gpio_chip = &hw->chip;
 
-	/* Be greedy to guess first gpio_n is equal to eint_n */
-	if (desc[eint_n].eint.eint_n == eint_n)
+	/*
+	 * Be greedy to guess first gpio_n is equal to eint_n.
+	 * Only eint virtual eint number is greater than gpio number.
+	 */
+	if (hw->soc->npins > eint_n &&
+	    desc[eint_n].eint.eint_n == eint_n)
 		*gpio_n = eint_n;
 	else
 		*gpio_n = mtk_xt_find_eint_num(hw, eint_n);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
@@ -1038,6 +1038,7 @@
 	node = of_parse_phandle(np, "mediatek,pctl-regmap", 0);
 	if (node) {
 		pctl->regmap1 = syscon_node_to_regmap(node);
+		of_node_put(node);
 		if (IS_ERR(pctl->regmap1))
 			return PTR_ERR(pctl->regmap1);
 	} else if (regmap) {
@@ -1051,6 +1052,7 @@
 	node = of_parse_phandle(np, "mediatek,pctl-regmap", 1);
 	if (node) {
 		pctl->regmap2 = syscon_node_to_regmap(node);
+		of_node_put(node);
 		if (IS_ERR(pctl->regmap2))
 			return PTR_ERR(pctl->regmap2);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mediatek/pinctrl-paris.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mediatek/pinctrl-paris.c
@@ -79,82 +79,76 @@
 {
 	struct mtk_pinctrl *hw = pinctrl_dev_get_drvdata(pctldev);
 	u32 param = pinconf_to_config_param(*config);
-	int pullup, err, reg, ret = 1;
+	int pullup, reg, err = -ENOTSUPP, ret = 1;
 	const struct mtk_pin_desc *desc;
 
-	if (pin >= hw->soc->npins) {
-		err = -EINVAL;
-		goto out;
-	}
+	if (pin >= hw->soc->npins)
+		return -EINVAL;
+
 	desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
 
 	switch (param) {
 	case PIN_CONFIG_BIAS_DISABLE:
 	case PIN_CONFIG_BIAS_PULL_UP:
 	case PIN_CONFIG_BIAS_PULL_DOWN:
-		if (hw->soc->bias_get_combo) {
-			err = hw->soc->bias_get_combo(hw, desc, &pullup, &ret);
-			if (err)
-				goto out;
-			if (param == PIN_CONFIG_BIAS_DISABLE) {
-				if (ret == MTK_PUPD_SET_R1R0_00)
-					ret = MTK_DISABLE;
-			} else if (param == PIN_CONFIG_BIAS_PULL_UP) {
-				/* When desire to get pull-up value, return
-				 *  error if current setting is pull-down
-				 */
-				if (!pullup)
-					err = -EINVAL;
-			} else if (param == PIN_CONFIG_BIAS_PULL_DOWN) {
-				/* When desire to get pull-down value, return
-				 *  error if current setting is pull-up
-				 */
-				if (pullup)
-					err = -EINVAL;
-			}
-		} else {
-			err = -ENOTSUPP;
+		if (!hw->soc->bias_get_combo)
+			break;
+		err = hw->soc->bias_get_combo(hw, desc, &pullup, &ret);
+		if (err)
+			break;
+		if (ret == MTK_PUPD_SET_R1R0_00)
+			ret = MTK_DISABLE;
+		if (param == PIN_CONFIG_BIAS_DISABLE) {
+			if (ret != MTK_DISABLE)
+				err = -EINVAL;
+		} else if (param == PIN_CONFIG_BIAS_PULL_UP) {
+			if (!pullup || ret == MTK_DISABLE)
+				err = -EINVAL;
+		} else if (param == PIN_CONFIG_BIAS_PULL_DOWN) {
+			if (pullup || ret == MTK_DISABLE)
+				err = -EINVAL;
 		}
 		break;
 	case PIN_CONFIG_SLEW_RATE:
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_SR, &ret);
 		break;
 	case PIN_CONFIG_INPUT_ENABLE:
-	case PIN_CONFIG_OUTPUT_ENABLE:
+		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_IES, &ret);
+		if (!ret)
+			err = -EINVAL;
+		break;
+	case PIN_CONFIG_OUTPUT:
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DIR, &ret);
 		if (err)
-			goto out;
-		/*     CONFIG     Current direction return value
-		 * -------------  ----------------- ----------------------
-		 * OUTPUT_ENABLE       output       1 (= HW value)
-		 *                     input        0 (= HW value)
-		 * INPUT_ENABLE        output       0 (= reverse HW value)
-		 *                     input        1 (= reverse HW value)
-		 */
-		if (param == PIN_CONFIG_INPUT_ENABLE)
-			ret = !ret;
+			break;
 
+		if (!ret) {
+			err = -EINVAL;
+			break;
+		}
+
+		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DO, &ret);
 		break;
 	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DIR, &ret);
 		if (err)
-			goto out;
+			break;
 		/* return error when in output mode
 		 * because schmitt trigger only work in input mode
 		 */
 		if (ret) {
 			err = -EINVAL;
-			goto out;
+			break;
 		}
 
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_SMT, &ret);
-
+		if (!ret)
+			err = -EINVAL;
 		break;
 	case PIN_CONFIG_DRIVE_STRENGTH:
-		if (hw->soc->drive_get)
-			err = hw->soc->drive_get(hw, desc, &ret);
-		else
-			err = -ENOTSUPP;
+		if (!hw->soc->drive_get)
+			break;
+		err = hw->soc->drive_get(hw, desc, &ret);
 		break;
 	case MTK_PIN_CONFIG_TDSEL:
 	case MTK_PIN_CONFIG_RDSEL:
@@ -164,23 +158,18 @@
 		break;
 	case MTK_PIN_CONFIG_PU_ADV:
 	case MTK_PIN_CONFIG_PD_ADV:
-		if (hw->soc->adv_pull_get) {
-			pullup = param == MTK_PIN_CONFIG_PU_ADV;
-			err = hw->soc->adv_pull_get(hw, desc, pullup, &ret);
-		} else
-			err = -ENOTSUPP;
+		if (!hw->soc->adv_pull_get)
+			break;
+		pullup = param == MTK_PIN_CONFIG_PU_ADV;
+		err = hw->soc->adv_pull_get(hw, desc, pullup, &ret);
 		break;
 	case MTK_PIN_CONFIG_DRV_ADV:
-		if (hw->soc->adv_drive_get)
-			err = hw->soc->adv_drive_get(hw, desc, &ret);
-		else
-			err = -ENOTSUPP;
+		if (!hw->soc->adv_drive_get)
+			break;
+		err = hw->soc->adv_drive_get(hw, desc, &ret);
 		break;
-	default:
-		err = -ENOTSUPP;
 	}
 
-out:
 	if (!err)
 		*config = pinconf_to_config_packed(param, ret);
 
@@ -188,59 +177,37 @@
 }
 
 static int mtk_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
-			   enum pin_config_param param,
-			   enum pin_config_param arg)
+			   enum pin_config_param param, u32 arg)
 {
 	struct mtk_pinctrl *hw = pinctrl_dev_get_drvdata(pctldev);
 	const struct mtk_pin_desc *desc;
-	int err = 0;
+	int err = -ENOTSUPP;
 	u32 reg;
 
-	if (pin >= hw->soc->npins) {
-		err = -EINVAL;
-		goto err;
-	}
+	if (pin >= hw->soc->npins)
+		return -EINVAL;
+
 	desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin];
 
 	switch ((u32)param) {
 	case PIN_CONFIG_BIAS_DISABLE:
-		if (hw->soc->bias_set_combo)
-			err = hw->soc->bias_set_combo(hw, desc, 0, MTK_DISABLE);
-		else
-			err = -ENOTSUPP;
+		if (!hw->soc->bias_set_combo)
+			break;
+		err = hw->soc->bias_set_combo(hw, desc, 0, MTK_DISABLE);
 		break;
 	case PIN_CONFIG_BIAS_PULL_UP:
-		if (hw->soc->bias_set_combo)
-			err = hw->soc->bias_set_combo(hw, desc, 1, arg);
-		else
-			err = -ENOTSUPP;
+		if (!hw->soc->bias_set_combo)
+			break;
+		err = hw->soc->bias_set_combo(hw, desc, 1, arg);
 		break;
 	case PIN_CONFIG_BIAS_PULL_DOWN:
-		if (hw->soc->bias_set_combo)
-			err = hw->soc->bias_set_combo(hw, desc, 0, arg);
-		else
-			err = -ENOTSUPP;
-		break;
-	case PIN_CONFIG_OUTPUT_ENABLE:
-		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_SMT,
-				       MTK_DISABLE);
-		/* Keep set direction to consider the case that a GPIO pin
-		 *  does not have SMT control
-		 */
-		if (err != -ENOTSUPP)
-			goto err;
-
-		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
-				       MTK_OUTPUT);
+		if (!hw->soc->bias_set_combo)
+			break;
+		err = hw->soc->bias_set_combo(hw, desc, 0, arg);
 		break;
 	case PIN_CONFIG_INPUT_ENABLE:
 		/* regard all non-zero value as enable */
 		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_IES, !!arg);
-		if (err)
-			goto err;
-
-		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
-				       MTK_INPUT);
 		break;
 	case PIN_CONFIG_SLEW_RATE:
 		/* regard all non-zero value as enable */
@@ -250,7 +217,7 @@
 		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DO,
 				       arg);
 		if (err)
-			goto err;
+			break;
 
 		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
 				       MTK_OUTPUT);
@@ -262,15 +229,14 @@
 		 */
 		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR, !arg);
 		if (err)
-			goto err;
+			break;
 
 		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_SMT, !!arg);
 		break;
 	case PIN_CONFIG_DRIVE_STRENGTH:
-		if (hw->soc->drive_set)
-			err = hw->soc->drive_set(hw, desc, arg);
-		else
-			err = -ENOTSUPP;
+		if (!hw->soc->drive_set)
+			break;
+		err = hw->soc->drive_set(hw, desc, arg);
 		break;
 	case MTK_PIN_CONFIG_TDSEL:
 	case MTK_PIN_CONFIG_RDSEL:
@@ -280,26 +246,19 @@
 		break;
 	case MTK_PIN_CONFIG_PU_ADV:
 	case MTK_PIN_CONFIG_PD_ADV:
-		if (hw->soc->adv_pull_set) {
-			bool pullup;
-
-			pullup = param == MTK_PIN_CONFIG_PU_ADV;
-			err = hw->soc->adv_pull_set(hw, desc, pullup,
-						    arg);
-		} else
-			err = -ENOTSUPP;
+		if (!hw->soc->adv_pull_set)
+			break;
+		err = hw->soc->adv_pull_set(hw, desc,
+					    (param == MTK_PIN_CONFIG_PU_ADV),
+					    arg);
 		break;
 	case MTK_PIN_CONFIG_DRV_ADV:
-		if (hw->soc->adv_drive_set)
-			err = hw->soc->adv_drive_set(hw, desc, arg);
-		else
-			err = -ENOTSUPP;
+		if (!hw->soc->adv_drive_set)
+			break;
+		err = hw->soc->adv_drive_set(hw, desc, arg);
 		break;
-	default:
-		err = -ENOTSUPP;
 	}
 
-err:
 	return err;
 }
 
@@ -577,14 +536,17 @@
 	mtk_hw_get_value_wrap(hw, gpio, PINCTRL_PIN_REG_DRV)
 
 ssize_t mtk_pctrl_show_one_pin(struct mtk_pinctrl *hw,
-	unsigned int gpio, char *buf, unsigned int bufLen)
+	unsigned int gpio, char *buf, unsigned int buf_len)
 {
-	int pinmux, pullup, pullen, len = 0, r1 = -1, r0 = -1;
+	int pinmux, pullup = 0, pullen = 0, len = 0, r1 = -1, r0 = -1;
 	const struct mtk_pin_desc *desc;
 
 	if (gpio >= hw->soc->npins)
 		return -EINVAL;
 
+	if (mtk_is_virt_gpio(hw, gpio))
+		return -EINVAL;
+
 	desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio];
 	pinmux = mtk_pctrl_get_pinmux(hw, gpio);
 	if (pinmux >= hw->soc->nfuncs)
@@ -610,7 +572,7 @@
 	} else if (pullen != MTK_DISABLE && pullen != MTK_ENABLE) {
 		pullen = 0;
 	}
-	len += scnprintf(buf + len, bufLen - len,
+	len += scnprintf(buf + len, buf_len - len,
 			"%03d: %1d%1d%1d%1d%02d%1d%1d%1d%1d",
 			gpio,
 			pinmux,
@@ -624,10 +586,10 @@
 			pullup);
 
 	if (r1 != -1) {
-		len += scnprintf(buf + len, bufLen - len, " (%1d %1d)\n",
+		len += scnprintf(buf + len, buf_len - len, " (%1d %1d)\n",
 			r1, r0);
 	} else {
-		len += scnprintf(buf + len, bufLen - len, "\n");
+		len += scnprintf(buf + len, buf_len - len, "\n");
 	}
 
 	return len;
@@ -639,7 +601,7 @@
 			  unsigned int gpio)
 {
 	struct mtk_pinctrl *hw = pinctrl_dev_get_drvdata(pctldev);
-	char buf[PIN_DBG_BUF_SZ];
+	char buf[PIN_DBG_BUF_SZ] = { 0 };
 
 	(void)mtk_pctrl_show_one_pin(hw, gpio, buf, PIN_DBG_BUF_SZ);
 
@@ -719,10 +681,10 @@
 			       unsigned long *config)
 {
 	struct mtk_pinctrl *hw = pinctrl_dev_get_drvdata(pctldev);
+	struct mtk_pinctrl_group *grp = &hw->groups[group];
 
-	*config = hw->groups[group].config;
-
-	return 0;
+	 /* One pin per group only */
+	return mtk_pinconf_get(pctldev, grp->pin, config);
 }
 
 static int mtk_pconf_group_set(struct pinctrl_dev *pctldev, unsigned group,
@@ -738,8 +700,6 @@
 				      pinconf_to_config_argument(configs[i]));
 		if (ret < 0)
 			return ret;
-
-		grp->config = configs[i];
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/meson/pinctrl-meson-a1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/meson/pinctrl-meson-a1.c
@@ -250,7 +250,7 @@
 static const unsigned int pdm_din2_a_pins[]		= { GPIOA_6 };
 static const unsigned int pdm_din1_a_pins[]		= { GPIOA_7 };
 static const unsigned int pdm_din0_a_pins[]		= { GPIOA_8 };
-static const unsigned int pdm_dclk_pins[]		= { GPIOA_9 };
+static const unsigned int pdm_dclk_a_pins[]		= { GPIOA_9 };
 
 /* gen_clk */
 static const unsigned int gen_clk_x_pins[]		= { GPIOX_7 };
@@ -591,7 +591,7 @@
 	GROUP(pdm_din2_a,		3),
 	GROUP(pdm_din1_a,		3),
 	GROUP(pdm_din0_a,		3),
-	GROUP(pdm_dclk,			3),
+	GROUP(pdm_dclk_a,		3),
 	GROUP(pwm_c_a,			3),
 	GROUP(pwm_b_a,			3),
 
@@ -755,7 +755,7 @@
 
 static const char * const pdm_groups[] = {
 	"pdm_din0_x", "pdm_din1_x", "pdm_din2_x", "pdm_dclk_x", "pdm_din2_a",
-	"pdm_din1_a", "pdm_din0_a", "pdm_dclk",
+	"pdm_din1_a", "pdm_din0_a", "pdm_dclk_a",
 };
 
 static const char * const gen_clk_groups[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/meson/pinctrl-meson-axg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/meson/pinctrl-meson-axg.c
@@ -400,6 +400,7 @@
 	GPIO_GROUP(GPIOA_15),
 	GPIO_GROUP(GPIOA_16),
 	GPIO_GROUP(GPIOA_17),
+	GPIO_GROUP(GPIOA_18),
 	GPIO_GROUP(GPIOA_19),
 	GPIO_GROUP(GPIOA_20),
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mvebu/pinctrl-armada-37xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mvebu/pinctrl-armada-37xx.c
@@ -341,12 +341,12 @@
 				       struct armada_37xx_pin_group *grp)
 {
 	struct armada_37xx_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+	struct device *dev = info->dev;
 	unsigned int reg = SELECTION;
 	unsigned int mask = grp->reg_mask;
 	int func, val;
 
-	dev_dbg(info->dev, "enable function %s group %s\n",
-		name, grp->name);
+	dev_dbg(dev, "enable function %s group %s\n", name, grp->name);
 
 	func = match_string(grp->funcs, NB_FUNCS, name);
 	if (func < 0)
@@ -722,25 +722,22 @@
 static int armada_37xx_irqchip_register(struct platform_device *pdev,
 					struct armada_37xx_pinctrl *info)
 {
-	struct device_node *np = info->dev->of_node;
 	struct gpio_chip *gc = &info->gpio_chip;
 	struct irq_chip *irqchip = &info->irq_chip;
 	struct gpio_irq_chip *girq = &gc->irq;
 	struct device *dev = &pdev->dev;
-	struct resource res;
+	struct device_node *np;
 	int ret = -ENODEV, i, nr_irq_parent;
 
 	/* Check if we have at least one gpio-controller child node */
-	for_each_child_of_node(info->dev->of_node, np) {
+	for_each_child_of_node(dev->of_node, np) {
 		if (of_property_read_bool(np, "gpio-controller")) {
 			ret = 0;
 			break;
 		}
 	}
-	if (ret) {
-		dev_err(dev, "no gpio-controller child node\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "no gpio-controller child node\n");
 
 	nr_irq_parent = of_irq_count(np);
 	spin_lock_init(&info->irq_lock);
@@ -750,12 +747,7 @@
 		return 0;
 	}
 
-	if (of_address_to_resource(info->dev->of_node, 1, &res)) {
-		dev_err(dev, "cannot find IO resource\n");
-		return -ENOENT;
-	}
-
-	info->base = devm_ioremap_resource(info->dev, &res);
+	info->base = devm_platform_ioremap_resource(pdev, 1);
 	if (IS_ERR(info->base))
 		return PTR_ERR(info->base);
 
@@ -774,14 +766,13 @@
 	 * the chained irq with all of them.
 	 */
 	girq->num_parents = nr_irq_parent;
-	girq->parents = devm_kcalloc(&pdev->dev, nr_irq_parent,
-				     sizeof(*girq->parents), GFP_KERNEL);
+	girq->parents = devm_kcalloc(dev, nr_irq_parent, sizeof(*girq->parents), GFP_KERNEL);
 	if (!girq->parents)
 		return -ENOMEM;
 	for (i = 0; i < nr_irq_parent; i++) {
 		int irq = irq_of_parse_and_map(np, i);
 
-		if (irq < 0)
+		if (!irq)
 			continue;
 		girq->parents[i] = irq;
 	}
@@ -794,11 +785,12 @@
 static int armada_37xx_gpiochip_register(struct platform_device *pdev,
 					struct armada_37xx_pinctrl *info)
 {
+	struct device *dev = &pdev->dev;
 	struct device_node *np;
 	struct gpio_chip *gc;
 	int ret = -ENODEV;
 
-	for_each_child_of_node(info->dev->of_node, np) {
+	for_each_child_of_node(dev->of_node, np) {
 		if (of_find_property(np, "gpio-controller", NULL)) {
 			ret = 0;
 			break;
@@ -811,7 +803,7 @@
 
 	gc = &info->gpio_chip;
 	gc->ngpio = info->data->nr_pins;
-	gc->parent = &pdev->dev;
+	gc->parent = dev;
 	gc->base = -1;
 	gc->of_node = np;
 	gc->label = info->data->name;
@@ -819,11 +811,8 @@
 	ret = armada_37xx_irqchip_register(pdev, info);
 	if (ret)
 		return ret;
-	ret = devm_gpiochip_add_data(&pdev->dev, gc, info);
-	if (ret)
-		return ret;
 
-	return 0;
+	return devm_gpiochip_add_data(dev, gc, info);
 }
 
 /**
@@ -874,13 +863,13 @@
 static int armada_37xx_fill_group(struct armada_37xx_pinctrl *info)
 {
 	int n, num = 0, funcsize = info->data->nr_pins;
+	struct device *dev = info->dev;
 
 	for (n = 0; n < info->ngroups; n++) {
 		struct armada_37xx_pin_group *grp = &info->groups[n];
 		int i, j, f;
 
-		grp->pins = devm_kcalloc(info->dev,
-					 grp->npins + grp->extra_npins,
+		grp->pins = devm_kcalloc(dev, grp->npins + grp->extra_npins,
 					 sizeof(*grp->pins),
 					 GFP_KERNEL);
 		if (!grp->pins)
@@ -898,8 +887,7 @@
 			ret = armada_37xx_add_function(info->funcs, &funcsize,
 					    grp->funcs[f]);
 			if (ret == -EOVERFLOW)
-				dev_err(info->dev,
-					"More functions than pins(%d)\n",
+				dev_err(dev, "More functions than pins(%d)\n",
 					info->data->nr_pins);
 			if (ret < 0)
 				continue;
@@ -925,6 +913,7 @@
 static int armada_37xx_fill_func(struct armada_37xx_pinctrl *info)
 {
 	struct armada_37xx_pmx_func *funcs = info->funcs;
+	struct device *dev = info->dev;
 	int n;
 
 	for (n = 0; n < info->nfuncs; n++) {
@@ -932,8 +921,7 @@
 		const char **groups;
 		int g;
 
-		funcs[n].groups = devm_kcalloc(info->dev,
-					       funcs[n].ngroups,
+		funcs[n].groups = devm_kcalloc(dev, funcs[n].ngroups,
 					       sizeof(*(funcs[n].groups)),
 					       GFP_KERNEL);
 		if (!funcs[n].groups)
@@ -962,6 +950,7 @@
 	const struct armada_37xx_pin_data *pin_data = info->data;
 	struct pinctrl_desc *ctrldesc = &info->pctl;
 	struct pinctrl_pin_desc *pindesc, *pdesc;
+	struct device *dev = &pdev->dev;
 	int pin, ret;
 
 	info->groups = pin_data->groups;
@@ -973,9 +962,7 @@
 	ctrldesc->pmxops = &armada_37xx_pmx_ops;
 	ctrldesc->confops = &armada_37xx_pinconf_ops;
 
-	pindesc = devm_kcalloc(&pdev->dev,
-			       pin_data->nr_pins, sizeof(*pindesc),
-			       GFP_KERNEL);
+	pindesc = devm_kcalloc(dev, pin_data->nr_pins, sizeof(*pindesc), GFP_KERNEL);
 	if (!pindesc)
 		return -ENOMEM;
 
@@ -994,14 +981,10 @@
 	 * we allocate functions for number of pins and hope there are
 	 * fewer unique functions than pins available
 	 */
-	info->funcs = devm_kcalloc(&pdev->dev,
-				   pin_data->nr_pins,
-				   sizeof(struct armada_37xx_pmx_func),
-				   GFP_KERNEL);
+	info->funcs = devm_kcalloc(dev, pin_data->nr_pins, sizeof(*info->funcs), GFP_KERNEL);
 	if (!info->funcs)
 		return -ENOMEM;
 
-
 	ret = armada_37xx_fill_group(info);
 	if (ret)
 		return ret;
@@ -1010,11 +993,9 @@
 	if (ret)
 		return ret;
 
-	info->pctl_dev = devm_pinctrl_register(&pdev->dev, ctrldesc, info);
-	if (IS_ERR(info->pctl_dev)) {
-		dev_err(&pdev->dev, "could not register pinctrl driver\n");
-		return PTR_ERR(info->pctl_dev);
-	}
+	info->pctl_dev = devm_pinctrl_register(dev, ctrldesc, info);
+	if (IS_ERR(info->pctl_dev))
+		return dev_err_probe(dev, PTR_ERR(info->pctl_dev), "could not register pinctrl driver\n");
 
 	return 0;
 }
@@ -1135,28 +1116,40 @@
 	{ },
 };
 
+static const struct regmap_config armada_37xx_pinctrl_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.use_raw_spinlock = true,
+};
+
 static int __init armada_37xx_pinctrl_probe(struct platform_device *pdev)
 {
 	struct armada_37xx_pinctrl *info;
 	struct device *dev = &pdev->dev;
-	struct device_node *np = dev->of_node;
 	struct regmap *regmap;
+	void __iomem *base;
 	int ret;
 
-	info = devm_kzalloc(dev, sizeof(struct armada_37xx_pinctrl),
-			    GFP_KERNEL);
-	if (!info)
-		return -ENOMEM;
-
-	info->dev = dev;
+	base = devm_platform_get_and_ioremap_resource(pdev, 0, NULL);
+	if (IS_ERR(base)) {
+		dev_err(dev, "failed to ioremap base address: %pe\n", base);
+		return PTR_ERR(base);
+	}
 
-	regmap = syscon_node_to_regmap(np);
+	regmap = devm_regmap_init_mmio(dev, base,
+				       &armada_37xx_pinctrl_regmap_config);
 	if (IS_ERR(regmap)) {
-		dev_err(&pdev->dev, "cannot get regmap\n");
+		dev_err(dev, "failed to create regmap: %pe\n", regmap);
 		return PTR_ERR(regmap);
 	}
-	info->regmap = regmap;
 
+	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->dev = dev;
+	info->regmap = regmap;
 	info->data = of_device_get_match_data(dev);
 
 	ret = armada_37xx_pinctrl_register(pdev, info);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/mvebu/pinctrl-dove.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/mvebu/pinctrl-dove.c
@@ -769,7 +769,7 @@
 		of_match_device(dove_pinctrl_of_match, &pdev->dev);
 	struct mvebu_mpp_ctrl_data *mpp_data;
 	void __iomem *base;
-	int i;
+	int i, ret;
 
 	pdev->dev.platform_data = (void *)match->data;
 
@@ -784,15 +784,18 @@
 	}
 	clk_prepare_enable(clk);
 
-	mpp_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	base = devm_ioremap_resource(&pdev->dev, mpp_res);
-	if (IS_ERR(base))
-		return PTR_ERR(base);
+	base = devm_platform_get_and_ioremap_resource(pdev, 0, &mpp_res);
+	if (IS_ERR(base)) {
+		ret = PTR_ERR(base);
+		goto err_probe;
+	}
 
 	mpp_data = devm_kcalloc(&pdev->dev, dove_pinctrl_info.ncontrols,
 				sizeof(*mpp_data), GFP_KERNEL);
-	if (!mpp_data)
-		return -ENOMEM;
+	if (!mpp_data) {
+		ret = -ENOMEM;
+		goto err_probe;
+	}
 
 	dove_pinctrl_info.control_data = mpp_data;
 	for (i = 0; i < ARRAY_SIZE(dove_mpp_controls); i++)
@@ -811,8 +814,10 @@
 	}
 
 	mpp4_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(mpp4_base))
-		return PTR_ERR(mpp4_base);
+	if (IS_ERR(mpp4_base)) {
+		ret = PTR_ERR(mpp4_base);
+		goto err_probe;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
 	if (!res) {
@@ -823,8 +828,10 @@
 	}
 
 	pmu_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(pmu_base))
-		return PTR_ERR(pmu_base);
+	if (IS_ERR(pmu_base)) {
+		ret = PTR_ERR(pmu_base);
+		goto err_probe;
+	}
 
 	gconfmap = syscon_regmap_lookup_by_compatible("marvell,dove-global-config");
 	if (IS_ERR(gconfmap)) {
@@ -834,12 +841,17 @@
 		adjust_resource(&fb_res,
 			(mpp_res->start & INT_REGS_MASK) + GC_REGS_OFFS, 0x14);
 		gc_base = devm_ioremap_resource(&pdev->dev, &fb_res);
-		if (IS_ERR(gc_base))
-			return PTR_ERR(gc_base);
+		if (IS_ERR(gc_base)) {
+			ret = PTR_ERR(gc_base);
+			goto err_probe;
+		}
+
 		gconfmap = devm_regmap_init_mmio(&pdev->dev,
 						 gc_base, &gc_regmap_config);
-		if (IS_ERR(gconfmap))
-			return PTR_ERR(gconfmap);
+		if (IS_ERR(gconfmap)) {
+			ret = PTR_ERR(gconfmap);
+			goto err_probe;
+		}
 	}
 
 	/* Warn on any missing DT resource */
@@ -847,6 +859,9 @@
 		dev_warn(&pdev->dev, FW_BUG "Missing pinctrl regs in DTB. Please update your firmware.\n");
 
 	return mvebu_pinctrl_probe(pdev);
+err_probe:
+	clk_disable_unprepare(clk);
+	return ret;
 }
 
 static struct platform_driver dove_pinctrl_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/nomadik/pinctrl-nomadik.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/nomadik/pinctrl-nomadik.c
@@ -1421,8 +1421,10 @@
 
 	has_config = nmk_pinctrl_dt_get_config(np, &configs);
 	np_config = of_parse_phandle(np, "ste,config", 0);
-	if (np_config)
+	if (np_config) {
 		has_config |= nmk_pinctrl_dt_get_config(np_config, &configs);
+		of_node_put(np_config);
+	}
 	if (has_config) {
 		const char *gpio_name;
 		const char *pin;
@@ -1883,8 +1885,10 @@
 	}
 
 	prcm_np = of_parse_phandle(np, "prcm", 0);
-	if (prcm_np)
+	if (prcm_np) {
 		npct->prcm_base = of_iomap(prcm_np, 0);
+		of_node_put(prcm_np);
+	}
 	if (!npct->prcm_base) {
 		if (version == PINCTRL_NMK_STN8815) {
 			dev_info(&pdev->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/nuvoton/pinctrl-npcm7xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/nuvoton/pinctrl-npcm7xx.c
@@ -78,7 +78,6 @@
 	struct gpio_chip	gc;
 	int			irqbase;
 	int			irq;
-	void			*priv;
 	struct irq_chip		irq_chip;
 	u32			pinctrl_id;
 	int (*direction_input)(struct gpio_chip *chip, unsigned offset);
@@ -105,12 +104,12 @@
 	unsigned long flags;
 	unsigned long val;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	val = ioread32(reg) | pinmask;
 	iowrite32(val, reg);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void npcm_gpio_clr(struct gpio_chip *gc, void __iomem *reg,
@@ -119,12 +118,12 @@
 	unsigned long flags;
 	unsigned long val;
 
-	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	raw_spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	val = ioread32(reg) & ~pinmask;
 	iowrite32(val, reg);
 
-	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+	raw_spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 }
 
 static void npcmgpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
@@ -226,7 +225,7 @@
 	chained_irq_enter(chip, desc);
 	sts = ioread32(bank->base + NPCM7XX_GP_N_EVST);
 	en  = ioread32(bank->base + NPCM7XX_GP_N_EVEN);
-	dev_dbg(chip->parent_device, "==> got irq sts %.8x %.8x\n", sts,
+	dev_dbg(bank->gc.parent, "==> got irq sts %.8x %.8x\n", sts,
 		en);
 
 	sts &= en;
@@ -241,33 +240,33 @@
 		gpiochip_get_data(irq_data_get_irq_chip_data(d));
 	unsigned int gpio = BIT(d->hwirq);
 
-	dev_dbg(d->chip->parent_device, "setirqtype: %u.%u = %u\n", gpio,
+	dev_dbg(bank->gc.parent, "setirqtype: %u.%u = %u\n", gpio,
 		d->irq, type);
 	switch (type) {
 	case IRQ_TYPE_EDGE_RISING:
-		dev_dbg(d->chip->parent_device, "edge.rising\n");
+		dev_dbg(bank->gc.parent, "edge.rising\n");
 		npcm_gpio_clr(&bank->gc, bank->base + NPCM7XX_GP_N_EVBE, gpio);
 		npcm_gpio_clr(&bank->gc, bank->base + NPCM7XX_GP_N_POL, gpio);
 		break;
 	case IRQ_TYPE_EDGE_FALLING:
-		dev_dbg(d->chip->parent_device, "edge.falling\n");
+		dev_dbg(bank->gc.parent, "edge.falling\n");
 		npcm_gpio_clr(&bank->gc, bank->base + NPCM7XX_GP_N_EVBE, gpio);
 		npcm_gpio_set(&bank->gc, bank->base + NPCM7XX_GP_N_POL, gpio);
 		break;
 	case IRQ_TYPE_EDGE_BOTH:
-		dev_dbg(d->chip->parent_device, "edge.both\n");
+		dev_dbg(bank->gc.parent, "edge.both\n");
 		npcm_gpio_set(&bank->gc, bank->base + NPCM7XX_GP_N_EVBE, gpio);
 		break;
 	case IRQ_TYPE_LEVEL_LOW:
-		dev_dbg(d->chip->parent_device, "level.low\n");
+		dev_dbg(bank->gc.parent, "level.low\n");
 		npcm_gpio_set(&bank->gc, bank->base + NPCM7XX_GP_N_POL, gpio);
 		break;
 	case IRQ_TYPE_LEVEL_HIGH:
-		dev_dbg(d->chip->parent_device, "level.high\n");
+		dev_dbg(bank->gc.parent, "level.high\n");
 		npcm_gpio_clr(&bank->gc, bank->base + NPCM7XX_GP_N_POL, gpio);
 		break;
 	default:
-		dev_dbg(d->chip->parent_device, "invalid irq type\n");
+		dev_dbg(bank->gc.parent, "invalid irq type\n");
 		return -EINVAL;
 	}
 
@@ -289,7 +288,7 @@
 		gpiochip_get_data(irq_data_get_irq_chip_data(d));
 	unsigned int gpio = d->hwirq;
 
-	dev_dbg(d->chip->parent_device, "irq_ack: %u.%u\n", gpio, d->irq);
+	dev_dbg(bank->gc.parent, "irq_ack: %u.%u\n", gpio, d->irq);
 	iowrite32(BIT(gpio), bank->base + NPCM7XX_GP_N_EVST);
 }
 
@@ -301,7 +300,7 @@
 	unsigned int gpio = d->hwirq;
 
 	/* Clear events */
-	dev_dbg(d->chip->parent_device, "irq_mask: %u.%u\n", gpio, d->irq);
+	dev_dbg(bank->gc.parent, "irq_mask: %u.%u\n", gpio, d->irq);
 	iowrite32(BIT(gpio), bank->base + NPCM7XX_GP_N_EVENC);
 }
 
@@ -313,7 +312,7 @@
 	unsigned int gpio = d->hwirq;
 
 	/* Enable events */
-	dev_dbg(d->chip->parent_device, "irq_unmask: %u.%u\n", gpio, d->irq);
+	dev_dbg(bank->gc.parent, "irq_unmask: %u.%u\n", gpio, d->irq);
 	iowrite32(BIT(gpio), bank->base + NPCM7XX_GP_N_EVENS);
 }
 
@@ -323,7 +322,7 @@
 	unsigned int gpio = d->hwirq;
 
 	/* active-high, input, clear interrupt, enable interrupt */
-	dev_dbg(d->chip->parent_device, "startup: %u.%u\n", gpio, d->irq);
+	dev_dbg(gc->parent, "startup: %u.%u\n", gpio, d->irq);
 	npcmgpio_direction_input(gc, gpio);
 	npcmgpio_irq_ack(d);
 	npcmgpio_irq_unmask(d);
@@ -905,7 +904,7 @@
 #define DRIVE_STRENGTH_HI_SHIFT		12
 #define DRIVE_STRENGTH_MASK		0x0000FF00
 
-#define DS(lo, hi)	(((lo) << DRIVE_STRENGTH_LO_SHIFT) | \
+#define DSTR(lo, hi)	(((lo) << DRIVE_STRENGTH_LO_SHIFT) | \
 			 ((hi) << DRIVE_STRENGTH_HI_SHIFT))
 #define DSLO(x)		(((x) >> DRIVE_STRENGTH_LO_SHIFT) & 0xF)
 #define DSHI(x)		(((x) >> DRIVE_STRENGTH_HI_SHIFT) & 0xF)
@@ -925,31 +924,31 @@
 static const struct npcm7xx_pincfg pincfg[] = {
 	/*		PIN	  FUNCTION 1		   FUNCTION 2		  FUNCTION 3	    FLAGS */
 	NPCM7XX_PINCFG(0,	 iox1, MFSEL1, 30,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(1,	 iox1, MFSEL1, 30,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(2,	 iox1, MFSEL1, 30,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(1,	 iox1, MFSEL1, 30,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(2,	 iox1, MFSEL1, 30,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(3,	 iox1, MFSEL1, 30,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(4,	 iox2, MFSEL3, 14,	 smb1d, I2CSEGSEL, 7,	none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(5,	 iox2, MFSEL3, 14,	 smb1d, I2CSEGSEL, 7,	none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(6,	 iox2, MFSEL3, 14,	 smb2d, I2CSEGSEL, 10,  none, NONE, 0,       SLEW),
 	NPCM7XX_PINCFG(7,	 iox2, MFSEL3, 14,	 smb2d, I2CSEGSEL, 10,  none, NONE, 0,       SLEW),
-	NPCM7XX_PINCFG(8,      lkgpo1, FLOCKR1, 4,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(9,      lkgpo2, FLOCKR1, 8,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(10,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(11,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(8,      lkgpo1, FLOCKR1, 4,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(9,      lkgpo2, FLOCKR1, 8,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(10,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(11,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(12,	 gspi, MFSEL1, 24,	 smb5b, I2CSEGSEL, 19,  none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(13,	 gspi, MFSEL1, 24,	 smb5b, I2CSEGSEL, 19,  none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(14,	 gspi, MFSEL1, 24,	 smb5c, I2CSEGSEL, 20,	none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(15,	 gspi, MFSEL1, 24,	 smb5c, I2CSEGSEL, 20,	none, NONE, 0,	     SLEW),
-	NPCM7XX_PINCFG(16,     lkgpo0, FLOCKR1, 0,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(17,      pspi2, MFSEL3, 13,     smb4den, I2CSEGSEL, 23,  none, NONE, 0,       DS(8, 12)),
-	NPCM7XX_PINCFG(18,      pspi2, MFSEL3, 13,	 smb4b, I2CSEGSEL, 14,  none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(19,      pspi2, MFSEL3, 13,	 smb4b, I2CSEGSEL, 14,  none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(16,     lkgpo0, FLOCKR1, 0,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(17,      pspi2, MFSEL3, 13,     smb4den, I2CSEGSEL, 23,  none, NONE, 0,       DSTR(8, 12)),
+	NPCM7XX_PINCFG(18,      pspi2, MFSEL3, 13,	 smb4b, I2CSEGSEL, 14,  none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(19,      pspi2, MFSEL3, 13,	 smb4b, I2CSEGSEL, 14,  none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(20,	smb4c, I2CSEGSEL, 15,    smb15, MFSEL3, 8,      none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(21,	smb4c, I2CSEGSEL, 15,    smb15, MFSEL3, 8,      none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(22,      smb4d, I2CSEGSEL, 16,	 smb14, MFSEL3, 7,      none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(23,      smb4d, I2CSEGSEL, 16,	 smb14, MFSEL3, 7,      none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(24,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(25,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(24,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(25,	 ioxh, MFSEL3, 18,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(26,	 smb5, MFSEL1, 2,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(27,	 smb5, MFSEL1, 2,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(28,	 smb4, MFSEL1, 1,	  none, NONE, 0,	none, NONE, 0,	     0),
@@ -965,12 +964,12 @@
 	NPCM7XX_PINCFG(39,	smb3b, I2CSEGSEL, 11,	  none, NONE, 0,	none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(40,	smb3b, I2CSEGSEL, 11,	  none, NONE, 0,	none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(41,  bmcuart0a, MFSEL1, 9,         none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(42,  bmcuart0a, MFSEL1, 9,         none, NONE, 0,	none, NONE, 0,	     DS(2, 4) | GPO),
+	NPCM7XX_PINCFG(42,  bmcuart0a, MFSEL1, 9,         none, NONE, 0,	none, NONE, 0,	     DSTR(2, 4) | GPO),
 	NPCM7XX_PINCFG(43,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,  bmcuart1, MFSEL3, 24,    0),
 	NPCM7XX_PINCFG(44,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,  bmcuart1, MFSEL3, 24,    0),
 	NPCM7XX_PINCFG(45,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(46,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,	none, NONE, 0,	     DS(2, 8)),
-	NPCM7XX_PINCFG(47,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,	none, NONE, 0,	     DS(2, 8)),
+	NPCM7XX_PINCFG(46,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,	none, NONE, 0,	     DSTR(2, 8)),
+	NPCM7XX_PINCFG(47,      uart1, MFSEL1, 10,	 jtag2, MFSEL4, 0,	none, NONE, 0,	     DSTR(2, 8)),
 	NPCM7XX_PINCFG(48,	uart2, MFSEL1, 11,   bmcuart0b, MFSEL4, 1,      none, NONE, 0,	     GPO),
 	NPCM7XX_PINCFG(49,	uart2, MFSEL1, 11,   bmcuart0b, MFSEL4, 1,      none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(50,	uart2, MFSEL1, 11,	  none, NONE, 0,        none, NONE, 0,	     0),
@@ -980,8 +979,8 @@
 	NPCM7XX_PINCFG(54,	uart2, MFSEL1, 11,	  none, NONE, 0,        none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(55,	uart2, MFSEL1, 11,	  none, NONE, 0,        none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(56,	r1err, MFSEL1, 12,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(57,       r1md, MFSEL1, 13,        none, NONE, 0,        none, NONE, 0,       DS(2, 4)),
-	NPCM7XX_PINCFG(58,       r1md, MFSEL1, 13,        none, NONE, 0,	none, NONE, 0,	     DS(2, 4)),
+	NPCM7XX_PINCFG(57,       r1md, MFSEL1, 13,        none, NONE, 0,        none, NONE, 0,       DSTR(2, 4)),
+	NPCM7XX_PINCFG(58,       r1md, MFSEL1, 13,        none, NONE, 0,	none, NONE, 0,	     DSTR(2, 4)),
 	NPCM7XX_PINCFG(59,	smb3d, I2CSEGSEL, 13,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(60,	smb3d, I2CSEGSEL, 13,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(61,      uart1, MFSEL1, 10,	  none, NONE, 0,	none, NONE, 0,     GPO),
@@ -1004,19 +1003,19 @@
 	NPCM7XX_PINCFG(77,    fanin13, MFSEL2, 13,        none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(78,    fanin14, MFSEL2, 14,        none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(79,    fanin15, MFSEL2, 15,        none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(80,	 pwm0, MFSEL2, 16,        none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(81,	 pwm1, MFSEL2, 17,        none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(82,	 pwm2, MFSEL2, 18,        none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(83,	 pwm3, MFSEL2, 19,        none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(84,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(85,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(86,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     DS(8, 12) | SLEW),
+	NPCM7XX_PINCFG(80,	 pwm0, MFSEL2, 16,        none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(81,	 pwm1, MFSEL2, 17,        none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(82,	 pwm2, MFSEL2, 18,        none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(83,	 pwm3, MFSEL2, 19,        none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(84,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(85,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(86,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     DSTR(8, 12) | SLEW),
 	NPCM7XX_PINCFG(87,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(88,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(89,         r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(90,      r2err, MFSEL1, 15,        none, NONE, 0,        none, NONE, 0,       0),
-	NPCM7XX_PINCFG(91,       r2md, MFSEL1, 16,	  none, NONE, 0,        none, NONE, 0,	     DS(2, 4)),
-	NPCM7XX_PINCFG(92,       r2md, MFSEL1, 16,	  none, NONE, 0,        none, NONE, 0,	     DS(2, 4)),
+	NPCM7XX_PINCFG(91,       r2md, MFSEL1, 16,	  none, NONE, 0,        none, NONE, 0,	     DSTR(2, 4)),
+	NPCM7XX_PINCFG(92,       r2md, MFSEL1, 16,	  none, NONE, 0,        none, NONE, 0,	     DSTR(2, 4)),
 	NPCM7XX_PINCFG(93,    ga20kbc, MFSEL1, 17,	 smb5d, I2CSEGSEL, 21,  none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(94,    ga20kbc, MFSEL1, 17,	 smb5d, I2CSEGSEL, 21,  none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(95,	  lpc, NONE, 0,		  espi, MFSEL4, 8,      gpio, MFSEL1, 26,    0),
@@ -1062,34 +1061,34 @@
 	NPCM7XX_PINCFG(133,	smb10, MFSEL4, 13,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(134,	smb11, MFSEL4, 14,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(135,	smb11, MFSEL4, 14,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(136,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(137,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(138,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(139,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(140,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
+	NPCM7XX_PINCFG(136,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(137,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(138,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(139,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(140,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
 	NPCM7XX_PINCFG(141,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(142,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
+	NPCM7XX_PINCFG(142,	  sd1, MFSEL3, 12,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
 	NPCM7XX_PINCFG(143,       sd1, MFSEL3, 12,      sd1pwr, MFSEL4, 5,      none, NONE, 0,       0),
-	NPCM7XX_PINCFG(144,	 pwm4, MFSEL2, 20,	  none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(145,	 pwm5, MFSEL2, 21,	  none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(146,	 pwm6, MFSEL2, 22,	  none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(147,	 pwm7, MFSEL2, 23,	  none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(148,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(149,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(150,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(151,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(152,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
+	NPCM7XX_PINCFG(144,	 pwm4, MFSEL2, 20,	  none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(145,	 pwm5, MFSEL2, 21,	  none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(146,	 pwm6, MFSEL2, 22,	  none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(147,	 pwm7, MFSEL2, 23,	  none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(148,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(149,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(150,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(151,	 mmc8, MFSEL3, 11,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(152,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
 	NPCM7XX_PINCFG(153,     mmcwp, FLOCKR1, 24,       none, NONE, 0,	none, NONE, 0,	     0),  /* Z1/A1 */
-	NPCM7XX_PINCFG(154,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
+	NPCM7XX_PINCFG(154,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
 	NPCM7XX_PINCFG(155,     mmccd, MFSEL3, 25,      mmcrst, MFSEL4, 6,      none, NONE, 0,       0),  /* Z1/A1 */
-	NPCM7XX_PINCFG(156,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(157,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(158,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(159,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-
-	NPCM7XX_PINCFG(160,    clkout, MFSEL1, 21,        none, NONE, 0,        none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(161,	  lpc, NONE, 0,		  espi, MFSEL4, 8,      gpio, MFSEL1, 26,    DS(8, 12)),
-	NPCM7XX_PINCFG(162,    serirq, NONE, 0,           gpio, MFSEL1, 31,	none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(156,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(157,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(158,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(159,	  mmc, MFSEL3, 10,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+
+	NPCM7XX_PINCFG(160,    clkout, MFSEL1, 21,        none, NONE, 0,        none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(161,	  lpc, NONE, 0,		  espi, MFSEL4, 8,      gpio, MFSEL1, 26,    DSTR(8, 12)),
+	NPCM7XX_PINCFG(162,    serirq, NONE, 0,           gpio, MFSEL1, 31,	none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(163,	  lpc, NONE, 0,		  espi, MFSEL4, 8,      gpio, MFSEL1, 26,    0),
 	NPCM7XX_PINCFG(164,	  lpc, NONE, 0,		  espi, MFSEL4, 8,      gpio, MFSEL1, 26,    SLEWLPC),
 	NPCM7XX_PINCFG(165,	  lpc, NONE, 0,		  espi, MFSEL4, 8,      gpio, MFSEL1, 26,    SLEWLPC),
@@ -1102,25 +1101,25 @@
 	NPCM7XX_PINCFG(172,	 smb6, MFSEL3, 1,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(173,	 smb7, MFSEL3, 2,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(174,	 smb7, MFSEL3, 2,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(175,	pspi1, MFSEL3, 4,       faninx, MFSEL3, 3,      none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(176,     pspi1, MFSEL3, 4,       faninx, MFSEL3, 3,      none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(177,     pspi1, MFSEL3, 4,       faninx, MFSEL3, 3,      none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(178,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(179,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(180,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
+	NPCM7XX_PINCFG(175,	pspi1, MFSEL3, 4,       faninx, MFSEL3, 3,      none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(176,     pspi1, MFSEL3, 4,       faninx, MFSEL3, 3,      none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(177,     pspi1, MFSEL3, 4,       faninx, MFSEL3, 3,      none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(178,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(179,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(180,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
 	NPCM7XX_PINCFG(181,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(182,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(183,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(184,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW | GPO),
-	NPCM7XX_PINCFG(185,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW | GPO),
-	NPCM7XX_PINCFG(186,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(187,   spi3cs1, MFSEL4, 17,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
-	NPCM7XX_PINCFG(188,  spi3quad, MFSEL4, 20,     spi3cs2, MFSEL4, 18,     none, NONE, 0,    DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(189,  spi3quad, MFSEL4, 20,     spi3cs3, MFSEL4, 19,     none, NONE, 0,    DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(190,      gpio, FLOCKR1, 20,   nprd_smi, NONE, 0,	none, NONE, 0,	     DS(2, 4)),
-	NPCM7XX_PINCFG(191,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),  /* XX */
+	NPCM7XX_PINCFG(183,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(184,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW | GPO),
+	NPCM7XX_PINCFG(185,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW | GPO),
+	NPCM7XX_PINCFG(186,     spi3, MFSEL4, 16,	  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(187,   spi3cs1, MFSEL4, 17,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
+	NPCM7XX_PINCFG(188,  spi3quad, MFSEL4, 20,     spi3cs2, MFSEL4, 18,     none, NONE, 0,    DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(189,  spi3quad, MFSEL4, 20,     spi3cs3, MFSEL4, 19,     none, NONE, 0,    DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(190,      gpio, FLOCKR1, 20,   nprd_smi, NONE, 0,	none, NONE, 0,	     DSTR(2, 4)),
+	NPCM7XX_PINCFG(191,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),  /* XX */
 
-	NPCM7XX_PINCFG(192,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),  /* XX */
+	NPCM7XX_PINCFG(192,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),  /* XX */
 	NPCM7XX_PINCFG(193,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(194,	smb0b, I2CSEGSEL, 0,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(195,	smb0b, I2CSEGSEL, 0,	  none, NONE, 0,	none, NONE, 0,	     0),
@@ -1131,11 +1130,11 @@
 	NPCM7XX_PINCFG(200,        r2, MFSEL1, 14,        none, NONE, 0,        none, NONE, 0,       0),
 	NPCM7XX_PINCFG(201,	   r1, MFSEL3, 9,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(202,	smb0c, I2CSEGSEL, 1,	  none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(203,    faninx, MFSEL3, 3,         none, NONE, 0,	none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(203,    faninx, MFSEL3, 3,         none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(204,	  ddc, NONE, 0,           gpio, MFSEL3, 22,	none, NONE, 0,	     SLEW),
 	NPCM7XX_PINCFG(205,	  ddc, NONE, 0,           gpio, MFSEL3, 22,	none, NONE, 0,	     SLEW),
-	NPCM7XX_PINCFG(206,	  ddc, NONE, 0,           gpio, MFSEL3, 22,	none, NONE, 0,	     DS(4, 8)),
-	NPCM7XX_PINCFG(207,	  ddc, NONE, 0,           gpio, MFSEL3, 22,	none, NONE, 0,	     DS(4, 8)),
+	NPCM7XX_PINCFG(206,	  ddc, NONE, 0,           gpio, MFSEL3, 22,	none, NONE, 0,	     DSTR(4, 8)),
+	NPCM7XX_PINCFG(207,	  ddc, NONE, 0,           gpio, MFSEL3, 22,	none, NONE, 0,	     DSTR(4, 8)),
 	NPCM7XX_PINCFG(208,       rg2, MFSEL4, 24,         ddr, MFSEL3, 26,     none, NONE, 0,       0),
 	NPCM7XX_PINCFG(209,       rg2, MFSEL4, 24,         ddr, MFSEL3, 26,     none, NONE, 0,       0),
 	NPCM7XX_PINCFG(210,       rg2, MFSEL4, 24,         ddr, MFSEL3, 26,     none, NONE, 0,       0),
@@ -1147,20 +1146,20 @@
 	NPCM7XX_PINCFG(216,   rg2mdio, MFSEL4, 23,         ddr, MFSEL3, 26,     none, NONE, 0,       0),
 	NPCM7XX_PINCFG(217,   rg2mdio, MFSEL4, 23,         ddr, MFSEL3, 26,     none, NONE, 0,       0),
 	NPCM7XX_PINCFG(218,     wdog1, MFSEL3, 19,        none, NONE, 0,	none, NONE, 0,	     0),
-	NPCM7XX_PINCFG(219,     wdog2, MFSEL3, 20,        none, NONE, 0,	none, NONE, 0,	     DS(4, 8)),
+	NPCM7XX_PINCFG(219,     wdog2, MFSEL3, 20,        none, NONE, 0,	none, NONE, 0,	     DSTR(4, 8)),
 	NPCM7XX_PINCFG(220,	smb12, MFSEL3, 5,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(221,	smb12, MFSEL3, 5,	  none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(222,     smb13, MFSEL3, 6,         none, NONE, 0,	none, NONE, 0,	     0),
 	NPCM7XX_PINCFG(223,     smb13, MFSEL3, 6,         none, NONE, 0,	none, NONE, 0,	     0),
 
 	NPCM7XX_PINCFG(224,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     SLEW),
-	NPCM7XX_PINCFG(225,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW | GPO),
-	NPCM7XX_PINCFG(226,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW | GPO),
-	NPCM7XX_PINCFG(227,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(228,   spixcs1, MFSEL4, 28,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(229,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(230,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DS(8, 12) | SLEW),
-	NPCM7XX_PINCFG(231,    clkreq, MFSEL4, 9,         none, NONE, 0,        none, NONE, 0,	     DS(8, 12)),
+	NPCM7XX_PINCFG(225,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW | GPO),
+	NPCM7XX_PINCFG(226,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW | GPO),
+	NPCM7XX_PINCFG(227,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(228,   spixcs1, MFSEL4, 28,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(229,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(230,	 spix, MFSEL4, 27,        none, NONE, 0,	none, NONE, 0,	     DSTR(8, 12) | SLEW),
+	NPCM7XX_PINCFG(231,    clkreq, MFSEL4, 9,         none, NONE, 0,        none, NONE, 0,	     DSTR(8, 12)),
 	NPCM7XX_PINCFG(253,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     GPI), /* SDHC1 power */
 	NPCM7XX_PINCFG(254,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     GPI), /* SDHC2 power */
 	NPCM7XX_PINCFG(255,	 none, NONE, 0,		  none, NONE, 0,	none, NONE, 0,	     GPI), /* DACOSEL */
@@ -1561,7 +1560,7 @@
 {
 	struct npcm7xx_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev);
 
-	dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(npcm7xx_groups));
+	dev_dbg(npcm->dev, "group size: %zu\n", ARRAY_SIZE(npcm7xx_groups));
 	return ARRAY_SIZE(npcm7xx_groups);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinconf-generic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinconf-generic.c
@@ -30,10 +30,10 @@
 	PCONFDUMP(PIN_CONFIG_BIAS_BUS_HOLD, "input bias bus hold", NULL, false),
 	PCONFDUMP(PIN_CONFIG_BIAS_DISABLE, "input bias disabled", NULL, false),
 	PCONFDUMP(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, "input bias high impedance", NULL, false),
-	PCONFDUMP(PIN_CONFIG_BIAS_PULL_DOWN, "input bias pull down", NULL, false),
+	PCONFDUMP(PIN_CONFIG_BIAS_PULL_DOWN, "input bias pull down", "ohms", true),
 	PCONFDUMP(PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
-				"input bias pull to pin specific state", NULL, false),
-	PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", NULL, false),
+				"input bias pull to pin specific state", "ohms", true),
+	PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", "ohms", true),
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL, false),
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL, false),
 	PCONFDUMP(PIN_CONFIG_DRIVE_PUSH_PULL, "output drive push pull", NULL, false),
@@ -393,8 +393,10 @@
 	for_each_available_child_of_node(np_config, np) {
 		ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map,
 					&reserved_maps, num_maps, type);
-		if (ret < 0)
+		if (ret < 0) {
+			of_node_put(np);
 			goto exit;
+		}
 	}
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-amd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-amd.c
@@ -126,6 +126,14 @@
 	struct amd_gpio *gpio_dev = gpiochip_get_data(gc);
 
 	raw_spin_lock_irqsave(&gpio_dev->lock, flags);
+
+	/* Use special handling for Pin0 debounce */
+	if (offset == 0) {
+		pin_reg = readl(gpio_dev->base + WAKE_INT_MASTER_REG);
+		if (pin_reg & INTERNAL_GPIO0_DEBOUNCE)
+			debounce = 0;
+	}
+
 	pin_reg = readl(gpio_dev->base + offset * 4);
 
 	if (debounce) {
@@ -181,18 +189,6 @@
 	return ret;
 }
 
-static int amd_gpio_set_config(struct gpio_chip *gc, unsigned offset,
-			       unsigned long config)
-{
-	u32 debounce;
-
-	if (pinconf_to_config_param(config) != PIN_CONFIG_INPUT_DEBOUNCE)
-		return -ENOTSUPP;
-
-	debounce = pinconf_to_config_argument(config);
-	return amd_gpio_set_debounce(gc, offset, debounce);
-}
-
 #ifdef CONFIG_DEBUG_FS
 static void amd_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gc)
 {
@@ -223,6 +219,7 @@
 	char debounce_value[40];
 	char *debounce_enable;
 
+	seq_printf(s, "WAKE_INT_MASTER_REG: 0x%08x\n", readl(gpio_dev->base + WAKE_INT_MASTER_REG));
 	for (bank = 0; bank < gpio_dev->hwbank_num; bank++) {
 		seq_printf(s, "GPIO bank%d\t", bank);
 
@@ -598,14 +595,14 @@
 
 #define PIN_IRQ_PENDING	(BIT(INTERRUPT_STS_OFF) | BIT(WAKE_STS_OFF))
 
-static irqreturn_t amd_gpio_irq_handler(int irq, void *dev_id)
+static bool do_amd_gpio_irq_handler(int irq, void *dev_id)
 {
 	struct amd_gpio *gpio_dev = dev_id;
 	struct gpio_chip *gc = &gpio_dev->gc;
-	irqreturn_t ret = IRQ_NONE;
 	unsigned int i, irqnr;
 	unsigned long flags;
 	u32 __iomem *regs;
+	bool ret = false;
 	u32  regval;
 	u64 status, mask;
 
@@ -627,6 +624,16 @@
 		/* Each status bit covers four pins */
 		for (i = 0; i < 4; i++) {
 			regval = readl(regs + i);
+
+			if (regval & PIN_IRQ_PENDING)
+				dev_dbg(&gpio_dev->pdev->dev,
+					"GPIO %d is active: 0x%x",
+					irqnr + i, regval);
+
+			/* caused wake on resume context for shared IRQ */
+			if (irq < 0 && (regval & BIT(WAKE_STS_OFF)))
+				return true;
+
 			if (!(regval & PIN_IRQ_PENDING) ||
 			    !(regval & BIT(INTERRUPT_MASK_OFF)))
 				continue;
@@ -636,23 +643,26 @@
 			 * We must read the pin register again, in case the
 			 * value was changed while executing
 			 * generic_handle_domain_irq() above.
-			 * If we didn't find a mapping for the interrupt,
-			 * disable it in order to avoid a system hang caused
-			 * by an interrupt storm.
+			 * If the line is not an irq, disable it in order to
+			 * avoid a system hang caused by an interrupt storm.
 			 */
 			raw_spin_lock_irqsave(&gpio_dev->lock, flags);
 			regval = readl(regs + i);
-			if (irq == 0) {
-				regval &= ~BIT(INTERRUPT_ENABLE_OFF);
+			if (!gpiochip_line_is_irq(gc, irqnr + i)) {
+				regval &= ~BIT(INTERRUPT_MASK_OFF);
 				dev_dbg(&gpio_dev->pdev->dev,
 					"Disabling spurious GPIO IRQ %d\n",
 					irqnr + i);
+			} else {
+				ret = true;
 			}
 			writel(regval, regs + i);
 			raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
-			ret = IRQ_HANDLED;
 		}
 	}
+	/* did not cause wake on resume context for shared IRQ */
+	if (irq < 0)
+		return false;
 
 	/* Signal EOI to the GPIO unit */
 	raw_spin_lock_irqsave(&gpio_dev->lock, flags);
@@ -664,6 +674,16 @@
 	return ret;
 }
 
+static irqreturn_t amd_gpio_irq_handler(int irq, void *dev_id)
+{
+	return IRQ_RETVAL(do_amd_gpio_irq_handler(irq, dev_id));
+}
+
+static bool __maybe_unused amd_gpio_check_wake(void *dev_id)
+{
+	return do_amd_gpio_irq_handler(-1, dev_id);
+}
+
 static int amd_get_groups_count(struct pinctrl_dev *pctldev)
 {
 	struct amd_gpio *gpio_dev = pinctrl_dev_get_drvdata(pctldev);
@@ -732,7 +752,7 @@
 		break;
 
 	default:
-		dev_err(&gpio_dev->pdev->dev, "Invalid config param %04x\n",
+		dev_dbg(&gpio_dev->pdev->dev, "Invalid config param %04x\n",
 			param);
 		return -ENOTSUPP;
 	}
@@ -743,7 +763,7 @@
 }
 
 static int amd_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
-				unsigned long *configs, unsigned num_configs)
+			   unsigned long *configs, unsigned int num_configs)
 {
 	int i;
 	u32 arg;
@@ -785,7 +805,7 @@
 			break;
 
 		default:
-			dev_err(&gpio_dev->pdev->dev,
+			dev_dbg(&gpio_dev->pdev->dev,
 				"Invalid config param %04x\n", param);
 			ret = -ENOTSUPP;
 		}
@@ -833,6 +853,20 @@
 	return 0;
 }
 
+static int amd_gpio_set_config(struct gpio_chip *gc, unsigned int pin,
+			       unsigned long config)
+{
+	struct amd_gpio *gpio_dev = gpiochip_get_data(gc);
+
+	if (pinconf_to_config_param(config) == PIN_CONFIG_INPUT_DEBOUNCE) {
+		u32 debounce = pinconf_to_config_argument(config);
+
+		return amd_gpio_set_debounce(gc, pin, debounce);
+	}
+
+	return amd_pinconf_set(gpio_dev->pctrl, pin, &config, 1);
+}
+
 static const struct pinconf_ops amd_pinconf_ops = {
 	.pin_config_get		= amd_pinconf_get,
 	.pin_config_set		= amd_pinconf_set,
@@ -860,9 +894,9 @@
 
 		raw_spin_lock_irqsave(&gpio_dev->lock, flags);
 
-		pin_reg = readl(gpio_dev->base + i * 4);
+		pin_reg = readl(gpio_dev->base + pin * 4);
 		pin_reg &= ~mask;
-		writel(pin_reg, gpio_dev->base + i * 4);
+		writel(pin_reg, gpio_dev->base + pin * 4);
 
 		raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
 	}
@@ -891,6 +925,7 @@
 {
 	struct amd_gpio *gpio_dev = dev_get_drvdata(dev);
 	struct pinctrl_desc *desc = gpio_dev->pctrl->desc;
+	unsigned long flags;
 	int i;
 
 	for (i = 0; i < desc->npins; i++) {
@@ -899,7 +934,9 @@
 		if (!amd_gpio_should_save(gpio_dev, pin))
 			continue;
 
-		gpio_dev->saved_regs[i] = readl(gpio_dev->base + pin*4);
+		raw_spin_lock_irqsave(&gpio_dev->lock, flags);
+		gpio_dev->saved_regs[i] = readl(gpio_dev->base + pin * 4) & ~PIN_IRQ_PENDING;
+		raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
 	}
 
 	return 0;
@@ -909,6 +946,7 @@
 {
 	struct amd_gpio *gpio_dev = dev_get_drvdata(dev);
 	struct pinctrl_desc *desc = gpio_dev->pctrl->desc;
+	unsigned long flags;
 	int i;
 
 	for (i = 0; i < desc->npins; i++) {
@@ -917,7 +955,10 @@
 		if (!amd_gpio_should_save(gpio_dev, pin))
 			continue;
 
-		writel(gpio_dev->saved_regs[i], gpio_dev->base + pin*4);
+		raw_spin_lock_irqsave(&gpio_dev->lock, flags);
+		gpio_dev->saved_regs[i] |= readl(gpio_dev->base + pin * 4) & PIN_IRQ_PENDING;
+		writel(gpio_dev->saved_regs[i], gpio_dev->base + pin * 4);
+		raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
 	}
 
 	return 0;
@@ -1033,6 +1074,7 @@
 		goto out2;
 
 	platform_set_drvdata(pdev, gpio_dev);
+	acpi_register_wakeup_handler(gpio_dev->irq, amd_gpio_check_wake, gpio_dev);
 
 	dev_dbg(&pdev->dev, "amd gpio driver loaded\n");
 	return ret;
@@ -1050,6 +1092,7 @@
 	gpio_dev = platform_get_drvdata(pdev);
 
 	gpiochip_remove(&gpio_dev->gc);
+	acpi_unregister_wakeup_handler(amd_gpio_check_wake, gpio_dev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-amd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-amd.h
@@ -17,6 +17,7 @@
 #define AMD_GPIO_PINS_BANK3     32
 
 #define WAKE_INT_MASTER_REG 0xfc
+#define INTERNAL_GPIO0_DEBOUNCE (1 << 15)
 #define EOI_MASK (1 << 29)
 
 #define WAKE_INT_STATUS_REG0 0x2f8
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-at91-pio4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-at91-pio4.c
@@ -1038,6 +1038,13 @@
 	}
 };
 
+/*
+ * This lock class allows to tell lockdep that parent IRQ and children IRQ do
+ * not share the same class so it does not raise false positive
+ */
+static struct lock_class_key atmel_lock_key;
+static struct lock_class_key atmel_request_key;
+
 static int atmel_pinctrl_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -1126,8 +1133,10 @@
 
 		pin_desc[i].number = i;
 		/* Pin naming convention: P(bank_name)(bank_pin_number). */
-		pin_desc[i].name = kasprintf(GFP_KERNEL, "P%c%d",
-					     bank + 'A', line);
+		pin_desc[i].name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "P%c%d",
+						  bank + 'A', line);
+		if (!pin_desc[i].name)
+			return -ENOMEM;
 
 		group->name = group_names[i] = pin_desc[i].name;
 		group->pin = pin_desc[i].number;
@@ -1184,7 +1193,6 @@
 		dev_err(dev, "can't add the irq domain\n");
 		return -ENODEV;
 	}
-	atmel_pioctrl->irq_domain->name = "atmel gpio";
 
 	for (i = 0; i < atmel_pioctrl->npins; i++) {
 		int irq = irq_create_mapping(atmel_pioctrl->irq_domain, i);
@@ -1192,6 +1200,7 @@
 		irq_set_chip_and_handler(irq, &atmel_gpio_irq_chip,
 					 handle_simple_irq);
 		irq_set_chip_data(irq, atmel_pioctrl);
+		irq_set_lockdep_class(irq, &atmel_lock_key, &atmel_request_key);
 		dev_dbg(dev,
 			"atmel gpio irq domain: hwirq: %d, linux irq: %d\n",
 			i, irq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-at91.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-at91.c
@@ -1403,8 +1403,11 @@
 
 	/* We will handle a range of GPIO pins */
 	for (i = 0; i < gpio_banks; i++)
-		if (gpio_chips[i])
+		if (gpio_chips[i]) {
 			pinctrl_add_gpio_range(info->pctl, &gpio_chips[i]->range);
+			gpiochip_add_pin_range(&gpio_chips[i]->chip, dev_name(info->pctl->dev), 0,
+				gpio_chips[i]->range.pin_base, gpio_chips[i]->range.npins);
+		}
 
 	dev_info(&pdev->dev, "initialized AT91 pinctrl driver\n");
 
@@ -1891,7 +1894,7 @@
 	}
 
 	for (i = 0; i < chip->ngpio; i++)
-		names[i] = kasprintf(GFP_KERNEL, "pio%c%d", alias_idx + 'A', i);
+		names[i] = devm_kasprintf(&pdev->dev, GFP_KERNEL, "pio%c%d", alias_idx + 'A', i);
 
 	chip->names = (const char *const *)names;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-equilibrium.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-equilibrium.c
@@ -675,6 +675,11 @@
 		return ret;
 
 	for (i = 0; i < nr_funcs; i++) {
+
+		/* Ignore the same function with multiple groups */
+		if (funcs[i].name == NULL)
+			continue;
+
 		ret = pinmux_generic_add_function(drvdata->pctl_dev,
 						  funcs[i].name,
 						  funcs[i].groups,
@@ -815,7 +820,7 @@
 
 	ret = eqbr_build_functions(drvdata);
 	if (ret) {
-		dev_err(dev, "Failed to build groups\n");
+		dev_err(dev, "Failed to build functions\n");
 		return ret;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-ingenic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-ingenic.c
@@ -119,6 +119,8 @@
 	unsigned int num_functions;
 
 	const u32 *pull_ups, *pull_downs;
+
+	const struct regmap_access_table *access_table;
 };
 
 struct ingenic_pinctrl {
@@ -641,7 +643,7 @@
 static const struct group_desc jz4755_groups[] = {
 	INGENIC_PIN_GROUP("uart0-data", jz4755_uart0_data, 0),
 	INGENIC_PIN_GROUP("uart0-hwflow", jz4755_uart0_hwflow, 0),
-	INGENIC_PIN_GROUP("uart1-data", jz4755_uart1_data, 0),
+	INGENIC_PIN_GROUP("uart1-data", jz4755_uart1_data, 1),
 	INGENIC_PIN_GROUP("uart2-data", jz4755_uart2_data, 1),
 	INGENIC_PIN_GROUP("ssi-dt-b", jz4755_ssi_dt_b, 0),
 	INGENIC_PIN_GROUP("ssi-dt-f", jz4755_ssi_dt_f, 0),
@@ -695,7 +697,7 @@
 	"ssi-ce1-b", "ssi-ce1-f",
 };
 static const char *jz4755_mmc0_groups[] = { "mmc0-1bit", "mmc0-4bit", };
-static const char *jz4755_mmc1_groups[] = { "mmc0-1bit", "mmc0-4bit", };
+static const char *jz4755_mmc1_groups[] = { "mmc1-1bit", "mmc1-4bit", };
 static const char *jz4755_i2c_groups[] = { "i2c-data", };
 static const char *jz4755_cim_groups[] = { "cim-data", };
 static const char *jz4755_lcd_groups[] = {
@@ -2179,6 +2181,17 @@
 	{ "mac", x1000_mac_groups, ARRAY_SIZE(x1000_mac_groups), },
 };
 
+static const struct regmap_range x1000_access_ranges[] = {
+	regmap_reg_range(0x000, 0x400 - 4),
+	regmap_reg_range(0x700, 0x800 - 4),
+};
+
+/* shared with X1500 */
+static const struct regmap_access_table x1000_access_table = {
+	.yes_ranges = x1000_access_ranges,
+	.n_yes_ranges = ARRAY_SIZE(x1000_access_ranges),
+};
+
 static const struct ingenic_chip_info x1000_chip_info = {
 	.num_chips = 4,
 	.reg_offset = 0x100,
@@ -2189,6 +2202,7 @@
 	.num_functions = ARRAY_SIZE(x1000_functions),
 	.pull_ups = x1000_pull_ups,
 	.pull_downs = x1000_pull_downs,
+	.access_table = &x1000_access_table,
 };
 
 static int x1500_uart0_data_pins[] = { 0x4a, 0x4b, };
@@ -2300,6 +2314,7 @@
 	.num_functions = ARRAY_SIZE(x1500_functions),
 	.pull_ups = x1000_pull_ups,
 	.pull_downs = x1000_pull_downs,
+	.access_table = &x1000_access_table,
 };
 
 static const u32 x1830_pull_ups[4] = {
@@ -2506,6 +2521,16 @@
 	{ "mac", x1830_mac_groups, ARRAY_SIZE(x1830_mac_groups), },
 };
 
+static const struct regmap_range x1830_access_ranges[] = {
+	regmap_reg_range(0x0000, 0x4000 - 4),
+	regmap_reg_range(0x7000, 0x8000 - 4),
+};
+
+static const struct regmap_access_table x1830_access_table = {
+	.yes_ranges = x1830_access_ranges,
+	.n_yes_ranges = ARRAY_SIZE(x1830_access_ranges),
+};
+
 static const struct ingenic_chip_info x1830_chip_info = {
 	.num_chips = 4,
 	.reg_offset = 0x1000,
@@ -2516,6 +2541,7 @@
 	.num_functions = ARRAY_SIZE(x1830_functions),
 	.pull_ups = x1830_pull_ups,
 	.pull_downs = x1830_pull_downs,
+	.access_table = &x1830_access_table,
 };
 
 static const u32 x2000_pull_ups[5] = {
@@ -2969,6 +2995,17 @@
 	{ "otg", x2000_otg_groups, ARRAY_SIZE(x2000_otg_groups), },
 };
 
+static const struct regmap_range x2000_access_ranges[] = {
+	regmap_reg_range(0x000, 0x500 - 4),
+	regmap_reg_range(0x700, 0x800 - 4),
+};
+
+/* shared with X2100 */
+static const struct regmap_access_table x2000_access_table = {
+	.yes_ranges = x2000_access_ranges,
+	.n_yes_ranges = ARRAY_SIZE(x2000_access_ranges),
+};
+
 static const struct ingenic_chip_info x2000_chip_info = {
 	.num_chips = 5,
 	.reg_offset = 0x100,
@@ -2979,6 +3016,7 @@
 	.num_functions = ARRAY_SIZE(x2000_functions),
 	.pull_ups = x2000_pull_ups,
 	.pull_downs = x2000_pull_downs,
+	.access_table = &x2000_access_table,
 };
 
 static const u32 x2100_pull_ups[5] = {
@@ -3189,6 +3227,7 @@
 	.num_functions = ARRAY_SIZE(x2100_functions),
 	.pull_ups = x2100_pull_ups,
 	.pull_downs = x2100_pull_downs,
+	.access_table = &x2000_access_table,
 };
 
 static u32 ingenic_gpio_read_reg(struct ingenic_gpio_chip *jzgc, u8 reg)
@@ -4168,7 +4207,12 @@
 		return PTR_ERR(base);
 
 	regmap_config = ingenic_pinctrl_regmap_config;
-	regmap_config.max_register = chip_info->num_chips * chip_info->reg_offset;
+	if (chip_info->access_table) {
+		regmap_config.rd_table = chip_info->access_table;
+		regmap_config.wr_table = chip_info->access_table;
+	} else {
+		regmap_config.max_register = chip_info->num_chips * chip_info->reg_offset - 4;
+	}
 
 	jzpc->map = devm_regmap_init_mmio(dev, base, &regmap_config);
 	if (IS_ERR(jzpc->map)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-k210.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-k210.c
@@ -181,7 +181,7 @@
 	[K210_PC_DEFAULT_INT13] = K210_PC_MODE_IN | K210_PC_PU,
 };
 
-#undef DEFAULT
+#undef K210_PC_DEFAULT
 
 /*
  * Pin functions configuration information.
@@ -482,7 +482,7 @@
 {
 	int i;
 
-	for (i = K210_PC_DRIVE_MAX; i; i--) {
+	for (i = K210_PC_DRIVE_MAX; i >= 0; i--) {
 		if (k210_pinconf_drive_strength[i] <= max_strength_ua)
 			return i;
 	}
@@ -527,7 +527,7 @@
 	case PIN_CONFIG_BIAS_PULL_UP:
 		if (!arg)
 			return -EINVAL;
-		val |= K210_PC_PD;
+		val |= K210_PC_PU;
 		break;
 	case PIN_CONFIG_DRIVE_STRENGTH:
 		arg *= 1000;
@@ -862,8 +862,10 @@
 	for_each_available_child_of_node(np_config, np) {
 		ret = k210_pinctrl_dt_subnode_to_map(pctldev, np, map,
 						     &reserved_maps, num_maps);
-		if (ret < 0)
+		if (ret < 0) {
+			of_node_put(np);
 			goto err;
+		}
 	}
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-mcp23s08.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-mcp23s08.c
@@ -85,6 +85,7 @@
 	.num_reg_defaults = ARRAY_SIZE(mcp23x08_defaults),
 	.cache_type = REGCACHE_FLAT,
 	.max_register = MCP_OLAT,
+	.disable_locking = true, /* mcp->lock protects the regmap */
 };
 EXPORT_SYMBOL_GPL(mcp23x08_regmap);
 
@@ -131,6 +132,7 @@
 	.num_reg_defaults = ARRAY_SIZE(mcp23x17_defaults),
 	.cache_type = REGCACHE_FLAT,
 	.val_format_endian = REGMAP_ENDIAN_LITTLE,
+	.disable_locking = true, /* mcp->lock protects the regmap */
 };
 EXPORT_SYMBOL_GPL(mcp23x17_regmap);
 
@@ -228,7 +230,9 @@
 
 	switch (param) {
 	case PIN_CONFIG_BIAS_PULL_UP:
+		mutex_lock(&mcp->lock);
 		ret = mcp_read(mcp, MCP_GPPU, &data);
+		mutex_unlock(&mcp->lock);
 		if (ret < 0)
 			return ret;
 		status = (data & BIT(pin)) ? 1 : 0;
@@ -257,7 +261,9 @@
 
 		switch (param) {
 		case PIN_CONFIG_BIAS_PULL_UP:
+			mutex_lock(&mcp->lock);
 			ret = mcp_set_bit(mcp, MCP_GPPU, pin, arg);
+			mutex_unlock(&mcp->lock);
 			break;
 		default:
 			dev_dbg(mcp->dev, "Invalid config param %04x\n", param);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-mcp23s08_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-mcp23s08_spi.c
@@ -91,18 +91,28 @@
 		mcp->reg_shift = 0;
 		mcp->chip.ngpio = 8;
 		mcp->chip.label = devm_kasprintf(dev, GFP_KERNEL, "mcp23s08.%d", addr);
+		if (!mcp->chip.label)
+			return -ENOMEM;
 
 		config = &mcp23x08_regmap;
 		name = devm_kasprintf(dev, GFP_KERNEL, "%d", addr);
+		if (!name)
+			return -ENOMEM;
+
 		break;
 
 	case MCP_TYPE_S17:
 		mcp->reg_shift = 1;
 		mcp->chip.ngpio = 16;
 		mcp->chip.label = devm_kasprintf(dev, GFP_KERNEL, "mcp23s17.%d", addr);
+		if (!mcp->chip.label)
+			return -ENOMEM;
 
 		config = &mcp23x17_regmap;
 		name = devm_kasprintf(dev, GFP_KERNEL, "%d", addr);
+		if (!name)
+			return -ENOMEM;
+
 		break;
 
 	case MCP_TYPE_S18:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-microchip-sgpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-microchip-sgpio.c
@@ -17,6 +17,8 @@
 #include <linux/pinctrl/pinmux.h>
 #include <linux/platform_device.h>
 #include <linux/property.h>
+#include <linux/reset.h>
+#include <linux/spinlock.h>
 
 #include "core.h"
 #include "pinconf.h"
@@ -114,6 +116,7 @@
 	u32 clock;
 	u32 __iomem *regs;
 	const struct sgpio_properties *properties;
+	spinlock_t lock;
 };
 
 struct sgpio_port_addr {
@@ -215,6 +218,7 @@
 			     int value)
 {
 	unsigned int bit = SGPIO_SRC_BITS * addr->bit;
+	unsigned long flags;
 	u32 clr, set;
 
 	switch (priv->properties->arch) {
@@ -233,7 +237,10 @@
 	default:
 		return;
 	}
+
+	spin_lock_irqsave(&priv->lock, flags);
 	sgpio_clrsetbits(priv, REG_PORT_CONFIG, addr->port, clr, set);
+	spin_unlock_irqrestore(&priv->lock, flags);
 }
 
 static int sgpio_output_get(struct sgpio_priv *priv,
@@ -561,10 +568,13 @@
 	struct sgpio_bank *bank = gpiochip_get_data(chip);
 	unsigned int gpio = irqd_to_hwirq(data);
 	struct sgpio_port_addr addr;
+	unsigned long flags;
 	u32 ena;
 
 	sgpio_pin_to_addr(bank->priv, gpio, &addr);
 
+	spin_lock_irqsave(&bank->priv->lock, flags);
+
 	/* Disable interrupt while changing type */
 	ena = sgpio_readl(bank->priv, REG_INT_ENABLE, addr.bit);
 	sgpio_writel(bank->priv, ena & ~BIT(addr.port), REG_INT_ENABLE, addr.bit);
@@ -581,6 +591,8 @@
 
 	/* Possibly re-enable interrupts */
 	sgpio_writel(bank->priv, ena, REG_INT_ENABLE, addr.bit);
+
+	spin_unlock_irqrestore(&bank->priv->lock, flags);
 }
 
 static void microchip_sgpio_irq_setreg(struct irq_data *data,
@@ -591,13 +603,16 @@
 	struct sgpio_bank *bank = gpiochip_get_data(chip);
 	unsigned int gpio = irqd_to_hwirq(data);
 	struct sgpio_port_addr addr;
+	unsigned long flags;
 
 	sgpio_pin_to_addr(bank->priv, gpio, &addr);
 
+	spin_lock_irqsave(&bank->priv->lock, flags);
 	if (clear)
 		sgpio_clrsetbits(bank->priv, reg, addr.bit, BIT(addr.port), 0);
 	else
 		sgpio_clrsetbits(bank->priv, reg, addr.bit, 0, BIT(addr.port));
+	spin_unlock_irqrestore(&bank->priv->lock, flags);
 }
 
 static void microchip_sgpio_irq_mask(struct irq_data *data)
@@ -714,6 +729,9 @@
 	pctl_desc->name = devm_kasprintf(dev, GFP_KERNEL, "%s-%sput",
 					 dev_name(dev),
 					 bank->is_input ? "in" : "out");
+	if (!pctl_desc->name)
+		return -ENOMEM;
+
 	pctl_desc->pctlops = &sgpio_pctl_ops;
 	pctl_desc->pmxops = &sgpio_pmx_ops;
 	pctl_desc->confops = &sgpio_confops;
@@ -803,6 +821,7 @@
 	int div_clock = 0, ret, port, i, nbanks;
 	struct device *dev = &pdev->dev;
 	struct fwnode_handle *fwnode;
+	struct reset_control *reset;
 	struct sgpio_priv *priv;
 	struct clk *clk;
 	u32 val;
@@ -812,6 +831,12 @@
 		return -ENOMEM;
 
 	priv->dev = dev;
+	spin_lock_init(&priv->lock);
+
+	reset = devm_reset_control_get_optional_shared(&pdev->dev, "switch");
+	if (IS_ERR(reset))
+		return dev_err_probe(dev, PTR_ERR(reset), "Failed to get reset\n");
+	reset_control_reset(reset);
 
 	clk = devm_clk_get(dev, NULL);
 	if (IS_ERR(clk))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-ocelot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-ocelot.c
@@ -739,7 +739,7 @@
 	regmap_update_bits(info->map, REG_ALT(0, info, pin->pin),
 			   BIT(p), f << p);
 	regmap_update_bits(info->map, REG_ALT(1, info, pin->pin),
-			   BIT(p), f << (p - 1));
+			   BIT(p), (f >> 1) << p);
 
 	return 0;
 }
@@ -1279,21 +1279,21 @@
 	unsigned int reg = 0, irq, i;
 	unsigned long irqs;
 
+	chained_irq_enter(parent_chip, desc);
+
 	for (i = 0; i < info->stride; i++) {
 		regmap_read(info->map, id_reg + 4 * i, &reg);
 		if (!reg)
 			continue;
 
-		chained_irq_enter(parent_chip, desc);
-
 		irqs = reg;
 
 		for_each_set_bit(irq, &irqs,
 				 min(32U, info->desc->npins - 32 * i))
 			generic_handle_domain_irq(chip->irq.domain, irq + 32 * i);
-
-		chained_irq_exit(parent_chip, desc);
 	}
+
+	chained_irq_exit(parent_chip, desc);
 }
 
 static int ocelot_gpiochip_register(struct platform_device *pdev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-pistachio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-pistachio.c
@@ -1374,10 +1374,10 @@
 		}
 
 		irq = irq_of_parse_and_map(child, 0);
-		if (irq < 0) {
-			dev_err(pctl->dev, "No IRQ for bank %u: %d\n", i, irq);
+		if (!irq) {
+			dev_err(pctl->dev, "No IRQ for bank %u\n", i);
 			of_node_put(child);
-			ret = irq;
+			ret = -EINVAL;
 			goto err;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-rockchip.c
@@ -285,6 +285,7 @@
 {
 	struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
 	const struct rockchip_pin_group *grp;
+	struct device *dev = info->dev;
 	struct pinctrl_map *new_map;
 	struct device_node *parent;
 	int map_num = 1;
@@ -296,8 +297,7 @@
 	 */
 	grp = pinctrl_name_to_group(info, np->name);
 	if (!grp) {
-		dev_err(info->dev, "unable to find group for node %pOFn\n",
-			np);
+		dev_err(dev, "unable to find group for node %pOFn\n", np);
 		return -EINVAL;
 	}
 
@@ -331,7 +331,7 @@
 		new_map[i].data.configs.num_configs = grp->data[i].nconfigs;
 	}
 
-	dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
+	dev_dbg(dev, "maps: function %s group %s num %d\n",
 		(*map)->data.mux.function, (*map)->data.mux.group, map_num);
 
 	return 0;
@@ -455,117 +455,177 @@
 
 static struct rockchip_mux_recalced_data rk3308_mux_recalced_data[] = {
 	{
+		/* gpio1b6_sel */
 		.num = 1,
 		.pin = 14,
 		.reg = 0x28,
 		.bit = 12,
 		.mask = 0xf
 	}, {
+		/* gpio1b7_sel */
 		.num = 1,
 		.pin = 15,
 		.reg = 0x2c,
 		.bit = 0,
 		.mask = 0x3
 	}, {
+		/* gpio1c2_sel */
 		.num = 1,
 		.pin = 18,
 		.reg = 0x30,
 		.bit = 4,
 		.mask = 0xf
 	}, {
+		/* gpio1c3_sel */
 		.num = 1,
 		.pin = 19,
 		.reg = 0x30,
 		.bit = 8,
 		.mask = 0xf
 	}, {
+		/* gpio1c4_sel */
 		.num = 1,
 		.pin = 20,
 		.reg = 0x30,
 		.bit = 12,
 		.mask = 0xf
 	}, {
+		/* gpio1c5_sel */
 		.num = 1,
 		.pin = 21,
 		.reg = 0x34,
 		.bit = 0,
 		.mask = 0xf
 	}, {
+		/* gpio1c6_sel */
 		.num = 1,
 		.pin = 22,
 		.reg = 0x34,
 		.bit = 4,
 		.mask = 0xf
 	}, {
+		/* gpio1c7_sel */
 		.num = 1,
 		.pin = 23,
 		.reg = 0x34,
 		.bit = 8,
 		.mask = 0xf
 	}, {
+		/* gpio3b4_sel */
 		.num = 3,
 		.pin = 12,
 		.reg = 0x68,
 		.bit = 8,
 		.mask = 0xf
 	}, {
+		/* gpio3b5_sel */
 		.num = 3,
 		.pin = 13,
 		.reg = 0x68,
 		.bit = 12,
 		.mask = 0xf
 	}, {
+		/* gpio2a2_sel */
 		.num = 2,
 		.pin = 2,
-		.reg = 0x608,
-		.bit = 0,
-		.mask = 0x7
+		.reg = 0x40,
+		.bit = 4,
+		.mask = 0x3
 	}, {
+		/* gpio2a3_sel */
 		.num = 2,
 		.pin = 3,
-		.reg = 0x608,
-		.bit = 4,
-		.mask = 0x7
+		.reg = 0x40,
+		.bit = 6,
+		.mask = 0x3
 	}, {
+		/* gpio2c0_sel */
 		.num = 2,
 		.pin = 16,
-		.reg = 0x610,
-		.bit = 8,
-		.mask = 0x7
+		.reg = 0x50,
+		.bit = 0,
+		.mask = 0x3
 	}, {
+		/* gpio3b2_sel */
 		.num = 3,
 		.pin = 10,
-		.reg = 0x610,
-		.bit = 0,
-		.mask = 0x7
+		.reg = 0x68,
+		.bit = 4,
+		.mask = 0x3
 	}, {
+		/* gpio3b3_sel */
 		.num = 3,
 		.pin = 11,
-		.reg = 0x610,
-		.bit = 4,
-		.mask = 0x7
+		.reg = 0x68,
+		.bit = 6,
+		.mask = 0x3
 	},
 };
 
 static struct rockchip_mux_recalced_data rk3328_mux_recalced_data[] = {
 	{
-		.num = 2,
-		.pin = 12,
-		.reg = 0x24,
-		.bit = 8,
-		.mask = 0x3
-	}, {
+		/* gpio2_b7_sel */
 		.num = 2,
 		.pin = 15,
 		.reg = 0x28,
 		.bit = 0,
 		.mask = 0x7
 	}, {
+		/* gpio2_c7_sel */
 		.num = 2,
 		.pin = 23,
 		.reg = 0x30,
 		.bit = 14,
 		.mask = 0x3
+	}, {
+		/* gpio3_b1_sel */
+		.num = 3,
+		.pin = 9,
+		.reg = 0x44,
+		.bit = 2,
+		.mask = 0x3
+	}, {
+		/* gpio3_b2_sel */
+		.num = 3,
+		.pin = 10,
+		.reg = 0x44,
+		.bit = 4,
+		.mask = 0x3
+	}, {
+		/* gpio3_b3_sel */
+		.num = 3,
+		.pin = 11,
+		.reg = 0x44,
+		.bit = 6,
+		.mask = 0x3
+	}, {
+		/* gpio3_b4_sel */
+		.num = 3,
+		.pin = 12,
+		.reg = 0x44,
+		.bit = 8,
+		.mask = 0x3
+	}, {
+		/* gpio3_b5_sel */
+		.num = 3,
+		.pin = 13,
+		.reg = 0x44,
+		.bit = 10,
+		.mask = 0x3
+	}, {
+		/* gpio3_b6_sel */
+		.num = 3,
+		.pin = 14,
+		.reg = 0x44,
+		.bit = 12,
+		.mask = 0x3
+	}, {
+		/* gpio3_b7_sel */
+		.num = 3,
+		.pin = 15,
+		.reg = 0x44,
+		.bit = 14,
+		.mask = 0x3
 	},
 };
 
@@ -593,14 +653,54 @@
 }
 
 static struct rockchip_mux_route_data px30_mux_route_data[] = {
+	RK_MUXROUTE_SAME(2, RK_PB4, 1, 0x184, BIT(16 + 7)), /* cif-d0m0 */
+	RK_MUXROUTE_SAME(3, RK_PA1, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d0m1 */
+	RK_MUXROUTE_SAME(2, RK_PB6, 1, 0x184, BIT(16 + 7)), /* cif-d1m0 */
+	RK_MUXROUTE_SAME(3, RK_PA2, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d1m1 */
 	RK_MUXROUTE_SAME(2, RK_PA0, 1, 0x184, BIT(16 + 7)), /* cif-d2m0 */
 	RK_MUXROUTE_SAME(3, RK_PA3, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d2m1 */
+	RK_MUXROUTE_SAME(2, RK_PA1, 1, 0x184, BIT(16 + 7)), /* cif-d3m0 */
+	RK_MUXROUTE_SAME(3, RK_PA5, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d3m1 */
+	RK_MUXROUTE_SAME(2, RK_PA2, 1, 0x184, BIT(16 + 7)), /* cif-d4m0 */
+	RK_MUXROUTE_SAME(3, RK_PA7, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d4m1 */
+	RK_MUXROUTE_SAME(2, RK_PA3, 1, 0x184, BIT(16 + 7)), /* cif-d5m0 */
+	RK_MUXROUTE_SAME(3, RK_PB0, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d5m1 */
+	RK_MUXROUTE_SAME(2, RK_PA4, 1, 0x184, BIT(16 + 7)), /* cif-d6m0 */
+	RK_MUXROUTE_SAME(3, RK_PB1, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d6m1 */
+	RK_MUXROUTE_SAME(2, RK_PA5, 1, 0x184, BIT(16 + 7)), /* cif-d7m0 */
+	RK_MUXROUTE_SAME(3, RK_PB4, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d7m1 */
+	RK_MUXROUTE_SAME(2, RK_PA6, 1, 0x184, BIT(16 + 7)), /* cif-d8m0 */
+	RK_MUXROUTE_SAME(3, RK_PB6, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d8m1 */
+	RK_MUXROUTE_SAME(2, RK_PA7, 1, 0x184, BIT(16 + 7)), /* cif-d9m0 */
+	RK_MUXROUTE_SAME(3, RK_PB7, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d9m1 */
+	RK_MUXROUTE_SAME(2, RK_PB7, 1, 0x184, BIT(16 + 7)), /* cif-d10m0 */
+	RK_MUXROUTE_SAME(3, RK_PC6, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d10m1 */
+	RK_MUXROUTE_SAME(2, RK_PC0, 1, 0x184, BIT(16 + 7)), /* cif-d11m0 */
+	RK_MUXROUTE_SAME(3, RK_PC7, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-d11m1 */
+	RK_MUXROUTE_SAME(2, RK_PB0, 1, 0x184, BIT(16 + 7)), /* cif-vsyncm0 */
+	RK_MUXROUTE_SAME(3, RK_PD1, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-vsyncm1 */
+	RK_MUXROUTE_SAME(2, RK_PB1, 1, 0x184, BIT(16 + 7)), /* cif-hrefm0 */
+	RK_MUXROUTE_SAME(3, RK_PD2, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-hrefm1 */
+	RK_MUXROUTE_SAME(2, RK_PB2, 1, 0x184, BIT(16 + 7)), /* cif-clkinm0 */
+	RK_MUXROUTE_SAME(3, RK_PD3, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-clkinm1 */
+	RK_MUXROUTE_SAME(2, RK_PB3, 1, 0x184, BIT(16 + 7)), /* cif-clkoutm0 */
+	RK_MUXROUTE_SAME(3, RK_PD0, 3, 0x184, BIT(16 + 7) | BIT(7)), /* cif-clkoutm1 */
 	RK_MUXROUTE_SAME(3, RK_PC6, 2, 0x184, BIT(16 + 8)), /* pdm-m0 */
 	RK_MUXROUTE_SAME(2, RK_PC6, 1, 0x184, BIT(16 + 8) | BIT(8)), /* pdm-m1 */
+	RK_MUXROUTE_SAME(3, RK_PD3, 2, 0x184, BIT(16 + 8)), /* pdm-sdi0m0 */
+	RK_MUXROUTE_SAME(2, RK_PC5, 2, 0x184, BIT(16 + 8) | BIT(8)), /* pdm-sdi0m1 */
 	RK_MUXROUTE_SAME(1, RK_PD3, 2, 0x184, BIT(16 + 10)), /* uart2-rxm0 */
 	RK_MUXROUTE_SAME(2, RK_PB6, 2, 0x184, BIT(16 + 10) | BIT(10)), /* uart2-rxm1 */
+	RK_MUXROUTE_SAME(1, RK_PD2, 2, 0x184, BIT(16 + 10)), /* uart2-txm0 */
+	RK_MUXROUTE_SAME(2, RK_PB4, 2, 0x184, BIT(16 + 10) | BIT(10)), /* uart2-txm1 */
 	RK_MUXROUTE_SAME(0, RK_PC1, 2, 0x184, BIT(16 + 9)), /* uart3-rxm0 */
 	RK_MUXROUTE_SAME(1, RK_PB7, 2, 0x184, BIT(16 + 9) | BIT(9)), /* uart3-rxm1 */
+	RK_MUXROUTE_SAME(0, RK_PC0, 2, 0x184, BIT(16 + 9)), /* uart3-txm0 */
+	RK_MUXROUTE_SAME(1, RK_PB6, 2, 0x184, BIT(16 + 9) | BIT(9)), /* uart3-txm1 */
+	RK_MUXROUTE_SAME(0, RK_PC2, 2, 0x184, BIT(16 + 9)), /* uart3-ctsm0 */
+	RK_MUXROUTE_SAME(1, RK_PB4, 2, 0x184, BIT(16 + 9) | BIT(9)), /* uart3-ctsm1 */
+	RK_MUXROUTE_SAME(0, RK_PC3, 2, 0x184, BIT(16 + 9)), /* uart3-rtsm0 */
+	RK_MUXROUTE_SAME(1, RK_PB5, 2, 0x184, BIT(16 + 9) | BIT(9)), /* uart3-rtsm1 */
 };
 
 static struct rockchip_mux_route_data rk3128_mux_route_data[] = {
@@ -648,9 +748,8 @@
 	RK_MUXROUTE_SAME(0, RK_PC3, 1, 0x314, BIT(16 + 0) | BIT(0)), /* rtc_clk */
 	RK_MUXROUTE_SAME(1, RK_PC6, 2, 0x314, BIT(16 + 2) | BIT(16 + 3)), /* uart2_rxm0 */
 	RK_MUXROUTE_SAME(4, RK_PD2, 2, 0x314, BIT(16 + 2) | BIT(16 + 3) | BIT(2)), /* uart2_rxm1 */
-	RK_MUXROUTE_SAME(0, RK_PB7, 2, 0x608, BIT(16 + 8) | BIT(16 + 9)), /* i2c3_sdam0 */
-	RK_MUXROUTE_SAME(3, RK_PB4, 2, 0x608, BIT(16 + 8) | BIT(16 + 9) | BIT(8)), /* i2c3_sdam1 */
-	RK_MUXROUTE_SAME(2, RK_PA0, 3, 0x608, BIT(16 + 8) | BIT(16 + 9) | BIT(9)), /* i2c3_sdam2 */
+	RK_MUXROUTE_SAME(0, RK_PB7, 2, 0x314, BIT(16 + 4)), /* i2c3_sdam0 */
+	RK_MUXROUTE_SAME(3, RK_PB4, 2, 0x314, BIT(16 + 4) | BIT(4)), /* i2c3_sdam1 */
 	RK_MUXROUTE_SAME(1, RK_PA3, 2, 0x308, BIT(16 + 3)), /* i2s-8ch-1-sclktxm0 */
 	RK_MUXROUTE_SAME(1, RK_PA4, 2, 0x308, BIT(16 + 3)), /* i2s-8ch-1-sclkrxm0 */
 	RK_MUXROUTE_SAME(1, RK_PB5, 2, 0x308, BIT(16 + 3) | BIT(3)), /* i2s-8ch-1-sclktxm1 */
@@ -659,18 +758,6 @@
 	RK_MUXROUTE_SAME(1, RK_PB6, 4, 0x308, BIT(16 + 12) | BIT(16 + 13) | BIT(12)), /* pdm-clkm1 */
 	RK_MUXROUTE_SAME(2, RK_PA6, 2, 0x308, BIT(16 + 12) | BIT(16 + 13) | BIT(13)), /* pdm-clkm2 */
 	RK_MUXROUTE_SAME(2, RK_PA4, 3, 0x600, BIT(16 + 2) | BIT(2)), /* pdm-clkm-m2 */
-	RK_MUXROUTE_SAME(3, RK_PB2, 3, 0x314, BIT(16 + 9)), /* spi1_miso */
-	RK_MUXROUTE_SAME(2, RK_PA4, 2, 0x314, BIT(16 + 9) | BIT(9)), /* spi1_miso_m1 */
-	RK_MUXROUTE_SAME(0, RK_PB3, 3, 0x314, BIT(16 + 10) | BIT(16 + 11)), /* owire_m0 */
-	RK_MUXROUTE_SAME(1, RK_PC6, 7, 0x314, BIT(16 + 10) | BIT(16 + 11) | BIT(10)), /* owire_m1 */
-	RK_MUXROUTE_SAME(2, RK_PA2, 5, 0x314, BIT(16 + 10) | BIT(16 + 11) | BIT(11)), /* owire_m2 */
-	RK_MUXROUTE_SAME(0, RK_PB3, 2, 0x314, BIT(16 + 12) | BIT(16 + 13)), /* can_rxd_m0 */
-	RK_MUXROUTE_SAME(1, RK_PC6, 5, 0x314, BIT(16 + 12) | BIT(16 + 13) | BIT(12)), /* can_rxd_m1 */
-	RK_MUXROUTE_SAME(2, RK_PA2, 4, 0x314, BIT(16 + 12) | BIT(16 + 13) | BIT(13)), /* can_rxd_m2 */
-	RK_MUXROUTE_SAME(1, RK_PC4, 3, 0x314, BIT(16 + 14)), /* mac_rxd0_m0 */
-	RK_MUXROUTE_SAME(4, RK_PA2, 2, 0x314, BIT(16 + 14) | BIT(14)), /* mac_rxd0_m1 */
-	RK_MUXROUTE_SAME(3, RK_PB4, 4, 0x314, BIT(16 + 15)), /* uart3_rx */
-	RK_MUXROUTE_SAME(0, RK_PC1, 3, 0x314, BIT(16 + 15) | BIT(15)), /* uart3_rx_m1 */
 };
 
 static struct rockchip_mux_route_data rk3328_mux_route_data[] = {
@@ -703,19 +790,19 @@
 	RK_MUXROUTE_PMU(0, RK_PB5, 4, 0x0110, WRITE_MASK_VAL(3, 2, 1)), /* PWM1 IO mux M1 */
 	RK_MUXROUTE_PMU(0, RK_PC1, 1, 0x0110, WRITE_MASK_VAL(5, 4, 0)), /* PWM2 IO mux M0 */
 	RK_MUXROUTE_PMU(0, RK_PB6, 4, 0x0110, WRITE_MASK_VAL(5, 4, 1)), /* PWM2 IO mux M1 */
-	RK_MUXROUTE_PMU(0, RK_PB3, 2, 0x0300, WRITE_MASK_VAL(0, 0, 0)), /* CAN0 IO mux M0 */
+	RK_MUXROUTE_GRF(0, RK_PB3, 2, 0x0300, WRITE_MASK_VAL(0, 0, 0)), /* CAN0 IO mux M0 */
 	RK_MUXROUTE_GRF(2, RK_PA1, 4, 0x0300, WRITE_MASK_VAL(0, 0, 1)), /* CAN0 IO mux M1 */
 	RK_MUXROUTE_GRF(1, RK_PA1, 3, 0x0300, WRITE_MASK_VAL(2, 2, 0)), /* CAN1 IO mux M0 */
 	RK_MUXROUTE_GRF(4, RK_PC3, 3, 0x0300, WRITE_MASK_VAL(2, 2, 1)), /* CAN1 IO mux M1 */
 	RK_MUXROUTE_GRF(4, RK_PB5, 3, 0x0300, WRITE_MASK_VAL(4, 4, 0)), /* CAN2 IO mux M0 */
 	RK_MUXROUTE_GRF(2, RK_PB2, 4, 0x0300, WRITE_MASK_VAL(4, 4, 1)), /* CAN2 IO mux M1 */
 	RK_MUXROUTE_GRF(4, RK_PC4, 1, 0x0300, WRITE_MASK_VAL(6, 6, 0)), /* HPDIN IO mux M0 */
-	RK_MUXROUTE_PMU(0, RK_PC2, 2, 0x0300, WRITE_MASK_VAL(6, 6, 1)), /* HPDIN IO mux M1 */
+	RK_MUXROUTE_GRF(0, RK_PC2, 2, 0x0300, WRITE_MASK_VAL(6, 6, 1)), /* HPDIN IO mux M1 */
 	RK_MUXROUTE_GRF(3, RK_PB1, 3, 0x0300, WRITE_MASK_VAL(8, 8, 0)), /* GMAC1 IO mux M0 */
 	RK_MUXROUTE_GRF(4, RK_PA7, 3, 0x0300, WRITE_MASK_VAL(8, 8, 1)), /* GMAC1 IO mux M1 */
 	RK_MUXROUTE_GRF(4, RK_PD1, 1, 0x0300, WRITE_MASK_VAL(10, 10, 0)), /* HDMITX IO mux M0 */
-	RK_MUXROUTE_PMU(0, RK_PC7, 1, 0x0300, WRITE_MASK_VAL(10, 10, 1)), /* HDMITX IO mux M1 */
-	RK_MUXROUTE_PMU(0, RK_PB6, 1, 0x0300, WRITE_MASK_VAL(14, 14, 0)), /* I2C2 IO mux M0 */
+	RK_MUXROUTE_GRF(0, RK_PC7, 1, 0x0300, WRITE_MASK_VAL(10, 10, 1)), /* HDMITX IO mux M1 */
+	RK_MUXROUTE_GRF(0, RK_PB6, 1, 0x0300, WRITE_MASK_VAL(14, 14, 0)), /* I2C2 IO mux M0 */
 	RK_MUXROUTE_GRF(4, RK_PB4, 1, 0x0300, WRITE_MASK_VAL(14, 14, 1)), /* I2C2 IO mux M1 */
 	RK_MUXROUTE_GRF(1, RK_PA0, 1, 0x0304, WRITE_MASK_VAL(0, 0, 0)), /* I2C3 IO mux M0 */
 	RK_MUXROUTE_GRF(3, RK_PB6, 4, 0x0304, WRITE_MASK_VAL(0, 0, 1)), /* I2C3 IO mux M1 */
@@ -741,7 +828,7 @@
 	RK_MUXROUTE_GRF(4, RK_PC3, 1, 0x0308, WRITE_MASK_VAL(12, 12, 1)), /* PWM15 IO mux M1 */
 	RK_MUXROUTE_GRF(3, RK_PD2, 3, 0x0308, WRITE_MASK_VAL(14, 14, 0)), /* SDMMC2 IO mux M0 */
 	RK_MUXROUTE_GRF(3, RK_PA5, 5, 0x0308, WRITE_MASK_VAL(14, 14, 1)), /* SDMMC2 IO mux M1 */
-	RK_MUXROUTE_PMU(0, RK_PB5, 2, 0x030c, WRITE_MASK_VAL(0, 0, 0)), /* SPI0 IO mux M0 */
+	RK_MUXROUTE_GRF(0, RK_PB5, 2, 0x030c, WRITE_MASK_VAL(0, 0, 0)), /* SPI0 IO mux M0 */
 	RK_MUXROUTE_GRF(2, RK_PD3, 3, 0x030c, WRITE_MASK_VAL(0, 0, 1)), /* SPI0 IO mux M1 */
 	RK_MUXROUTE_GRF(2, RK_PB5, 3, 0x030c, WRITE_MASK_VAL(2, 2, 0)), /* SPI1 IO mux M0 */
 	RK_MUXROUTE_GRF(3, RK_PC3, 3, 0x030c, WRITE_MASK_VAL(2, 2, 1)), /* SPI1 IO mux M1 */
@@ -750,8 +837,8 @@
 	RK_MUXROUTE_GRF(4, RK_PB3, 4, 0x030c, WRITE_MASK_VAL(6, 6, 0)), /* SPI3 IO mux M0 */
 	RK_MUXROUTE_GRF(4, RK_PC2, 2, 0x030c, WRITE_MASK_VAL(6, 6, 1)), /* SPI3 IO mux M1 */
 	RK_MUXROUTE_GRF(2, RK_PB4, 2, 0x030c, WRITE_MASK_VAL(8, 8, 0)), /* UART1 IO mux M0 */
-	RK_MUXROUTE_PMU(0, RK_PD1, 1, 0x030c, WRITE_MASK_VAL(8, 8, 1)), /* UART1 IO mux M1 */
-	RK_MUXROUTE_PMU(0, RK_PD1, 1, 0x030c, WRITE_MASK_VAL(10, 10, 0)), /* UART2 IO mux M0 */
+	RK_MUXROUTE_GRF(3, RK_PD6, 4, 0x030c, WRITE_MASK_VAL(8, 8, 1)), /* UART1 IO mux M1 */
+	RK_MUXROUTE_GRF(0, RK_PD1, 1, 0x030c, WRITE_MASK_VAL(10, 10, 0)), /* UART2 IO mux M0 */
 	RK_MUXROUTE_GRF(1, RK_PD5, 2, 0x030c, WRITE_MASK_VAL(10, 10, 1)), /* UART2 IO mux M1 */
 	RK_MUXROUTE_GRF(1, RK_PA1, 2, 0x030c, WRITE_MASK_VAL(12, 12, 0)), /* UART3 IO mux M0 */
 	RK_MUXROUTE_GRF(3, RK_PB7, 4, 0x030c, WRITE_MASK_VAL(12, 12, 1)), /* UART3 IO mux M1 */
@@ -781,13 +868,13 @@
 	RK_MUXROUTE_GRF(3, RK_PD6, 5, 0x0314, WRITE_MASK_VAL(1, 0, 1)), /* PDM IO mux M1 */
 	RK_MUXROUTE_GRF(4, RK_PA0, 4, 0x0314, WRITE_MASK_VAL(1, 0, 1)), /* PDM IO mux M1 */
 	RK_MUXROUTE_GRF(3, RK_PC4, 5, 0x0314, WRITE_MASK_VAL(1, 0, 2)), /* PDM IO mux M2 */
-	RK_MUXROUTE_PMU(0, RK_PA5, 3, 0x0314, WRITE_MASK_VAL(3, 2, 0)), /* PCIE20 IO mux M0 */
+	RK_MUXROUTE_GRF(0, RK_PA5, 3, 0x0314, WRITE_MASK_VAL(3, 2, 0)), /* PCIE20 IO mux M0 */
 	RK_MUXROUTE_GRF(2, RK_PD0, 4, 0x0314, WRITE_MASK_VAL(3, 2, 1)), /* PCIE20 IO mux M1 */
 	RK_MUXROUTE_GRF(1, RK_PB0, 4, 0x0314, WRITE_MASK_VAL(3, 2, 2)), /* PCIE20 IO mux M2 */
-	RK_MUXROUTE_PMU(0, RK_PA4, 3, 0x0314, WRITE_MASK_VAL(5, 4, 0)), /* PCIE30X1 IO mux M0 */
+	RK_MUXROUTE_GRF(0, RK_PA4, 3, 0x0314, WRITE_MASK_VAL(5, 4, 0)), /* PCIE30X1 IO mux M0 */
 	RK_MUXROUTE_GRF(2, RK_PD2, 4, 0x0314, WRITE_MASK_VAL(5, 4, 1)), /* PCIE30X1 IO mux M1 */
 	RK_MUXROUTE_GRF(1, RK_PA5, 4, 0x0314, WRITE_MASK_VAL(5, 4, 2)), /* PCIE30X1 IO mux M2 */
-	RK_MUXROUTE_PMU(0, RK_PA6, 2, 0x0314, WRITE_MASK_VAL(7, 6, 0)), /* PCIE30X2 IO mux M0 */
+	RK_MUXROUTE_GRF(0, RK_PA6, 2, 0x0314, WRITE_MASK_VAL(7, 6, 0)), /* PCIE30X2 IO mux M0 */
 	RK_MUXROUTE_GRF(2, RK_PD4, 4, 0x0314, WRITE_MASK_VAL(7, 6, 1)), /* PCIE30X2 IO mux M1 */
 	RK_MUXROUTE_GRF(4, RK_PC2, 4, 0x0314, WRITE_MASK_VAL(7, 6, 2)), /* PCIE30X2 IO mux M2 */
 };
@@ -872,20 +959,20 @@
 			       int pin, int mux)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
+	struct device *dev = info->dev;
 	int iomux_num = (pin / 8);
 
 	if (iomux_num > 3)
 		return -EINVAL;
 
 	if (bank->iomux[iomux_num].type & IOMUX_UNROUTED) {
-		dev_err(info->dev, "pin %d is unrouted\n", pin);
+		dev_err(dev, "pin %d is unrouted\n", pin);
 		return -EINVAL;
 	}
 
 	if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY) {
 		if (mux != RK_FUNC_GPIO) {
-			dev_err(info->dev,
-				"pin %d only supports a gpio mux\n", pin);
+			dev_err(dev, "pin %d only supports a gpio mux\n", pin);
 			return -ENOTSUPP;
 		}
 	}
@@ -909,6 +996,7 @@
 static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
+	struct device *dev = info->dev;
 	int iomux_num = (pin / 8);
 	struct regmap *regmap;
 	int reg, ret, mask, mux_type;
@@ -922,8 +1010,7 @@
 	if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY)
 		return 0;
 
-	dev_dbg(info->dev, "setting mux of GPIO%d-%d to %d\n",
-						bank->bank_num, pin, mux);
+	dev_dbg(dev, "setting mux of GPIO%d-%d to %d\n", bank->bank_num, pin, mux);
 
 	regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
 				? info->regmap_pmu : info->regmap_base;
@@ -984,9 +1071,9 @@
 #define PX30_PULL_PINS_PER_REG		8
 #define PX30_PULL_BANK_STRIDE		16
 
-static void px30_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				       int pin_num, struct regmap **regmap,
-				       int *reg, u8 *bit)
+static int px30_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+				      int pin_num, struct regmap **regmap,
+				      int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1006,6 +1093,8 @@
 	*reg += ((pin_num / PX30_PULL_PINS_PER_REG) * 4);
 	*bit = (pin_num % PX30_PULL_PINS_PER_REG);
 	*bit *= PX30_PULL_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define PX30_DRV_PMU_OFFSET		0x20
@@ -1014,9 +1103,9 @@
 #define PX30_DRV_PINS_PER_REG		8
 #define PX30_DRV_BANK_STRIDE		16
 
-static void px30_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-				      int pin_num, struct regmap **regmap,
-				      int *reg, u8 *bit)
+static int px30_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				     int pin_num, struct regmap **regmap,
+				     int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1036,6 +1125,8 @@
 	*reg += ((pin_num / PX30_DRV_PINS_PER_REG) * 4);
 	*bit = (pin_num % PX30_DRV_PINS_PER_REG);
 	*bit *= PX30_DRV_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define PX30_SCHMITT_PMU_OFFSET			0x38
@@ -1075,9 +1166,9 @@
 #define RV1108_PULL_BITS_PER_PIN	2
 #define RV1108_PULL_BANK_STRIDE		16
 
-static void rv1108_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-					 int pin_num, struct regmap **regmap,
-					 int *reg, u8 *bit)
+static int rv1108_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1096,6 +1187,8 @@
 	*reg += ((pin_num / RV1108_PULL_PINS_PER_REG) * 4);
 	*bit = (pin_num % RV1108_PULL_PINS_PER_REG);
 	*bit *= RV1108_PULL_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define RV1108_DRV_PMU_OFFSET		0x20
@@ -1104,9 +1197,9 @@
 #define RV1108_DRV_PINS_PER_REG		8
 #define RV1108_DRV_BANK_STRIDE		16
 
-static void rv1108_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-					int pin_num, struct regmap **regmap,
-					int *reg, u8 *bit)
+static int rv1108_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1126,6 +1219,8 @@
 	*reg += ((pin_num / RV1108_DRV_PINS_PER_REG) * 4);
 	*bit = pin_num % RV1108_DRV_PINS_PER_REG;
 	*bit *= RV1108_DRV_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define RV1108_SCHMITT_PMU_OFFSET		0x30
@@ -1182,9 +1277,9 @@
 #define RK2928_PULL_PINS_PER_REG	16
 #define RK2928_PULL_BANK_STRIDE		8
 
-static void rk2928_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk2928_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1194,13 +1289,15 @@
 	*reg += (pin_num / RK2928_PULL_PINS_PER_REG) * 4;
 
 	*bit = pin_num % RK2928_PULL_PINS_PER_REG;
+
+	return 0;
 };
 
 #define RK3128_PULL_OFFSET	0x118
 
-static void rk3128_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-					 int pin_num, struct regmap **regmap,
-					 int *reg, u8 *bit)
+static int rk3128_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1210,6 +1307,8 @@
 	*reg += ((pin_num / RK2928_PULL_PINS_PER_REG) * 4);
 
 	*bit = pin_num % RK2928_PULL_PINS_PER_REG;
+
+	return 0;
 }
 
 #define RK3188_PULL_OFFSET		0x164
@@ -1218,9 +1317,9 @@
 #define RK3188_PULL_BANK_STRIDE		16
 #define RK3188_PULL_PMU_OFFSET		0x64
 
-static void rk3188_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3188_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1250,12 +1349,14 @@
 		*bit = 7 - (pin_num % RK3188_PULL_PINS_PER_REG);
 		*bit *= RK3188_PULL_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 #define RK3288_PULL_OFFSET		0x140
-static void rk3288_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3288_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1279,6 +1380,8 @@
 		*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
 		*bit *= RK3188_PULL_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 #define RK3288_DRV_PMU_OFFSET		0x70
@@ -1287,9 +1390,9 @@
 #define RK3288_DRV_PINS_PER_REG		8
 #define RK3288_DRV_BANK_STRIDE		16
 
-static void rk3288_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3288_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1313,13 +1416,15 @@
 		*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
 		*bit *= RK3288_DRV_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 #define RK3228_PULL_OFFSET		0x100
 
-static void rk3228_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3228_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1330,13 +1435,15 @@
 
 	*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
 	*bit *= RK3188_PULL_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define RK3228_DRV_GRF_OFFSET		0x200
 
-static void rk3228_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3228_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1347,13 +1454,15 @@
 
 	*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
 	*bit *= RK3288_DRV_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define RK3308_PULL_OFFSET		0xa0
 
-static void rk3308_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3308_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1364,13 +1473,15 @@
 
 	*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
 	*bit *= RK3188_PULL_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define RK3308_DRV_GRF_OFFSET		0x100
 
-static void rk3308_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3308_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1381,14 +1492,16 @@
 
 	*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
 	*bit *= RK3288_DRV_BITS_PER_PIN;
+
+	return 0;
 }
 
 #define RK3368_PULL_GRF_OFFSET		0x100
 #define RK3368_PULL_PMU_OFFSET		0x10
 
-static void rk3368_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3368_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1412,14 +1525,16 @@
 		*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
 		*bit *= RK3188_PULL_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 #define RK3368_DRV_PMU_OFFSET		0x20
 #define RK3368_DRV_GRF_OFFSET		0x200
 
-static void rk3368_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-				    int pin_num, struct regmap **regmap,
-				    int *reg, u8 *bit)
+static int rk3368_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1443,15 +1558,17 @@
 		*bit = (pin_num % RK3288_DRV_PINS_PER_REG);
 		*bit *= RK3288_DRV_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 #define RK3399_PULL_GRF_OFFSET		0xe040
 #define RK3399_PULL_PMU_OFFSET		0x40
 #define RK3399_DRV_3BITS_PER_PIN	3
 
-static void rk3399_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-					 int pin_num, struct regmap **regmap,
-					 int *reg, u8 *bit)
+static int rk3399_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1477,11 +1594,13 @@
 		*bit = (pin_num % RK3188_PULL_PINS_PER_REG);
 		*bit *= RK3188_PULL_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
-static void rk3399_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-					int pin_num, struct regmap **regmap,
-					int *reg, u8 *bit)
+static int rk3399_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 	int drv_num = (pin_num / 8);
@@ -1498,6 +1617,8 @@
 		*bit = (pin_num % 8) * 3;
 	else
 		*bit = (pin_num % 8) * 2;
+
+	return 0;
 }
 
 #define RK3568_PULL_PMU_OFFSET		0x20
@@ -1506,9 +1627,9 @@
 #define RK3568_PULL_PINS_PER_REG	8
 #define RK3568_PULL_BANK_STRIDE		0x10
 
-static void rk3568_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
-					 int pin_num, struct regmap **regmap,
-					 int *reg, u8 *bit)
+static int rk3568_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+					int pin_num, struct regmap **regmap,
+					int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1529,6 +1650,8 @@
 		*bit = (pin_num % RK3568_PULL_PINS_PER_REG);
 		*bit *= RK3568_PULL_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 #define RK3568_DRV_PMU_OFFSET		0x70
@@ -1537,9 +1660,9 @@
 #define RK3568_DRV_PINS_PER_REG		2
 #define RK3568_DRV_BANK_STRIDE		0x40
 
-static void rk3568_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
-					int pin_num, struct regmap **regmap,
-					int *reg, u8 *bit)
+static int rk3568_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 
@@ -1560,6 +1683,8 @@
 		*bit = (pin_num % RK3568_DRV_PINS_PER_REG);
 		*bit *= RK3568_DRV_BITS_PER_PIN;
 	}
+
+	return 0;
 }
 
 static int rockchip_perpin_drv_list[DRV_TYPE_MAX][8] = {
@@ -1575,13 +1700,16 @@
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct device *dev = info->dev;
 	struct regmap *regmap;
 	int reg, ret;
 	u32 data, temp, rmask_bits;
 	u8 bit;
 	int drv_type = bank->drv[pin_num / 8].drv_type;
 
-	ctrl->drv_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	ret = ctrl->drv_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
 
 	switch (drv_type) {
 	case DRV_TYPE_IO_1V8_3V0_AUTO:
@@ -1620,7 +1748,7 @@
 			bit -= 16;
 			break;
 		default:
-			dev_err(info->dev, "unsupported bit: %d for pinctrl drive type: %d\n",
+			dev_err(dev, "unsupported bit: %d for pinctrl drive type: %d\n",
 				bit, drv_type);
 			return -EINVAL;
 		}
@@ -1632,8 +1760,7 @@
 		rmask_bits = RK3288_DRV_BITS_PER_PIN;
 		break;
 	default:
-		dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
-			drv_type);
+		dev_err(dev, "unsupported pinctrl drive type: %d\n", drv_type);
 		return -EINVAL;
 	}
 
@@ -1652,16 +1779,19 @@
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct device *dev = info->dev;
 	struct regmap *regmap;
 	int reg, ret, i;
 	u32 data, rmask, rmask_bits, temp;
 	u8 bit;
 	int drv_type = bank->drv[pin_num / 8].drv_type;
 
-	dev_dbg(info->dev, "setting drive of GPIO%d-%d to %d\n",
+	dev_dbg(dev, "setting drive of GPIO%d-%d to %d\n",
 		bank->bank_num, pin_num, strength);
 
-	ctrl->drv_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	ret = ctrl->drv_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
 	if (ctrl->type == RK3568) {
 		rmask_bits = RK3568_DRV_BITS_PER_PIN;
 		ret = (1 << (strength + 1)) - 1;
@@ -1680,8 +1810,7 @@
 	}
 
 	if (ret < 0) {
-		dev_err(info->dev, "unsupported driver strength %d\n",
-			strength);
+		dev_err(dev, "unsupported driver strength %d\n", strength);
 		return ret;
 	}
 
@@ -1720,7 +1849,7 @@
 			bit -= 16;
 			break;
 		default:
-			dev_err(info->dev, "unsupported bit: %d for pinctrl drive type: %d\n",
+			dev_err(dev, "unsupported bit: %d for pinctrl drive type: %d\n",
 				bit, drv_type);
 			return -EINVAL;
 		}
@@ -1731,8 +1860,7 @@
 		rmask_bits = RK3288_DRV_BITS_PER_PIN;
 		break;
 	default:
-		dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
-			drv_type);
+		dev_err(dev, "unsupported pinctrl drive type: %d\n", drv_type);
 		return -EINVAL;
 	}
 
@@ -1766,6 +1894,7 @@
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct device *dev = info->dev;
 	struct regmap *regmap;
 	int reg, ret, pull_type;
 	u8 bit;
@@ -1775,7 +1904,9 @@
 	if (ctrl->type == RK3066B)
 		return PIN_CONFIG_BIAS_DISABLE;
 
-	ctrl->pull_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	ret = ctrl->pull_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
 
 	ret = regmap_read(regmap, reg, &data);
 	if (ret)
@@ -1792,15 +1923,25 @@
 	case RK3188:
 	case RK3288:
 	case RK3308:
+	case RK3328:
 	case RK3368:
 	case RK3399:
+	case RK3568:
 		pull_type = bank->pull_type[pin_num / 8];
 		data >>= bit;
 		data &= (1 << RK3188_PULL_BITS_PER_PIN) - 1;
+		/*
+		 * In the TRM, pull-up being 1 for everything except the GPIO0_D3-D6,
+		 * where that pull up value becomes 3.
+		 */
+		if (ctrl->type == RK3568 && bank->bank_num == 0 && pin_num >= 27 && pin_num <= 30) {
+			if (data == 3)
+				data = 1;
+		}
 
 		return rockchip_pull_list[pull_type][data];
 	default:
-		dev_err(info->dev, "unsupported pinctrl type\n");
+		dev_err(dev, "unsupported pinctrl type\n");
 		return -EINVAL;
 	};
 }
@@ -1810,19 +1951,21 @@
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct device *dev = info->dev;
 	struct regmap *regmap;
 	int reg, ret, i, pull_type;
 	u8 bit;
 	u32 data, rmask;
 
-	dev_dbg(info->dev, "setting pull of GPIO%d-%d to %d\n",
-		 bank->bank_num, pin_num, pull);
+	dev_dbg(dev, "setting pull of GPIO%d-%d to %d\n", bank->bank_num, pin_num, pull);
 
 	/* rk3066b does support any pulls */
 	if (ctrl->type == RK3066B)
 		return pull ? -EINVAL : 0;
 
-	ctrl->pull_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	ret = ctrl->pull_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
 
 	switch (ctrl->type) {
 	case RK2928:
@@ -1837,6 +1980,7 @@
 	case RK3188:
 	case RK3288:
 	case RK3308:
+	case RK3328:
 	case RK3368:
 	case RK3399:
 	case RK3568:
@@ -1850,7 +1994,7 @@
 			}
 		}
 		/*
-		 * In the TRM, pull-up being 1 for everything except the GPIO0_D0-D6,
+		 * In the TRM, pull-up being 1 for everything except the GPIO0_D3-D6,
 		 * where that pull up value becomes 3.
 		 */
 		if (ctrl->type == RK3568 && bank->bank_num == 0 && pin_num >= 27 && pin_num <= 30) {
@@ -1859,8 +2003,7 @@
 		}
 
 		if (ret < 0) {
-			dev_err(info->dev, "unsupported pull setting %d\n",
-				pull);
+			dev_err(dev, "unsupported pull setting %d\n", pull);
 			return ret;
 		}
 
@@ -1872,7 +2015,7 @@
 		ret = regmap_update_bits(regmap, reg, rmask, data);
 		break;
 	default:
-		dev_err(info->dev, "unsupported pinctrl type\n");
+		dev_err(dev, "unsupported pinctrl type\n");
 		return -EINVAL;
 	}
 
@@ -1963,12 +2106,13 @@
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
 	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct device *dev = info->dev;
 	struct regmap *regmap;
 	int reg, ret;
 	u8 bit;
 	u32 data, rmask;
 
-	dev_dbg(info->dev, "setting input schmitt of GPIO%d-%d to %d\n",
+	dev_dbg(dev, "setting input schmitt of GPIO%d-%d to %d\n",
 		bank->bank_num, pin_num, enable);
 
 	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
@@ -2028,10 +2172,11 @@
 	struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
 	const unsigned int *pins = info->groups[group].pins;
 	const struct rockchip_pin_config *data = info->groups[group].data;
+	struct device *dev = info->dev;
 	struct rockchip_pin_bank *bank;
 	int cnt, ret = 0;
 
-	dev_dbg(info->dev, "enable function %s group %s\n",
+	dev_dbg(dev, "enable function %s group %s\n",
 		info->functions[selector].name, info->groups[group].name);
 
 	/*
@@ -2048,8 +2193,10 @@
 
 	if (ret) {
 		/* revert the already done pin settings */
-		for (cnt--; cnt >= 0; cnt--)
+		for (cnt--; cnt >= 0; cnt--) {
+			bank = pin_to_bank(info, pins[cnt]);
 			rockchip_set_mux(bank, pins[cnt] - bank->pin_base, 0);
+		}
 
 		return ret;
 	}
@@ -2057,11 +2204,24 @@
 	return 0;
 }
 
+static int rockchip_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
+					   struct pinctrl_gpio_range *range,
+					   unsigned offset,
+					   bool input)
+{
+	struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
+	struct rockchip_pin_bank *bank;
+
+	bank = pin_to_bank(info, offset);
+	return rockchip_set_mux(bank, offset - bank->pin_base, RK_FUNC_GPIO);
+}
+
 static const struct pinmux_ops rockchip_pmx_ops = {
 	.get_functions_count	= rockchip_pmx_get_funcs_count,
 	.get_function_name	= rockchip_pmx_get_func_name,
 	.get_function_groups	= rockchip_pmx_get_groups,
 	.set_mux		= rockchip_pmx_set,
+	.gpio_set_direction	= rockchip_pmx_gpio_set_direction,
 };
 
 /*
@@ -2083,6 +2243,7 @@
 	case RK3188:
 	case RK3288:
 	case RK3308:
+	case RK3328:
 	case RK3368:
 	case RK3399:
 	case RK3568:
@@ -2092,19 +2253,20 @@
 	return false;
 }
 
-static int rockchip_pinconf_defer_output(struct rockchip_pin_bank *bank,
-					 unsigned int pin, u32 arg)
+static int rockchip_pinconf_defer_pin(struct rockchip_pin_bank *bank,
+					 unsigned int pin, u32 param, u32 arg)
 {
-	struct rockchip_pin_output_deferred *cfg;
+	struct rockchip_pin_deferred *cfg;
 
 	cfg = kzalloc(sizeof(*cfg), GFP_KERNEL);
 	if (!cfg)
 		return -ENOMEM;
 
 	cfg->pin = pin;
+	cfg->param = param;
 	cfg->arg = arg;
 
-	list_add_tail(&cfg->head, &bank->deferred_output);
+	list_add_tail(&cfg->head, &bank->deferred_pins);
 
 	return 0;
 }
@@ -2125,6 +2287,25 @@
 		param = pinconf_to_config_param(configs[i]);
 		arg = pinconf_to_config_argument(configs[i]);
 
+		if (param == PIN_CONFIG_OUTPUT || param == PIN_CONFIG_INPUT_ENABLE) {
+			/*
+			 * Check for gpio driver not being probed yet.
+			 * The lock makes sure that either gpio-probe has completed
+			 * or the gpio driver hasn't probed yet.
+			 */
+			mutex_lock(&bank->deferred_lock);
+			if (!gpio || !gpio->direction_output) {
+				rc = rockchip_pinconf_defer_pin(bank, pin - bank->pin_base, param,
+								arg);
+				mutex_unlock(&bank->deferred_lock);
+				if (rc)
+					return rc;
+
+				break;
+			}
+			mutex_unlock(&bank->deferred_lock);
+		}
+
 		switch (param) {
 		case PIN_CONFIG_BIAS_DISABLE:
 			rc =  rockchip_set_pull(bank, pin - bank->pin_base,
@@ -2153,27 +2334,21 @@
 			if (rc != RK_FUNC_GPIO)
 				return -EINVAL;
 
-			/*
-			 * Check for gpio driver not being probed yet.
-			 * The lock makes sure that either gpio-probe has completed
-			 * or the gpio driver hasn't probed yet.
-			 */
-			mutex_lock(&bank->deferred_lock);
-			if (!gpio || !gpio->direction_output) {
-				rc = rockchip_pinconf_defer_output(bank, pin - bank->pin_base, arg);
-				mutex_unlock(&bank->deferred_lock);
-				if (rc)
-					return rc;
-
-				break;
-			}
-			mutex_unlock(&bank->deferred_lock);
-
 			rc = gpio->direction_output(gpio, pin - bank->pin_base,
 						    arg);
 			if (rc)
 				return rc;
 			break;
+		case PIN_CONFIG_INPUT_ENABLE:
+			rc = rockchip_set_mux(bank, pin - bank->pin_base,
+					      RK_FUNC_GPIO);
+			if (rc != RK_FUNC_GPIO)
+				return -EINVAL;
+
+			rc = gpio->direction_input(gpio, pin - bank->pin_base);
+			if (rc)
+				return rc;
+			break;
 		case PIN_CONFIG_DRIVE_STRENGTH:
 			/* rk3288 is the first with per-pin drive-strength */
 			if (!info->ctrl->drv_calc_reg)
@@ -2310,6 +2485,7 @@
 					      struct rockchip_pinctrl *info,
 					      u32 index)
 {
+	struct device *dev = info->dev;
 	struct rockchip_pin_bank *bank;
 	int size;
 	const __be32 *list;
@@ -2317,7 +2493,7 @@
 	int i, j;
 	int ret;
 
-	dev_dbg(info->dev, "group(%d): %pOFn\n", index, np);
+	dev_dbg(dev, "group(%d): %pOFn\n", index, np);
 
 	/* Initialise group */
 	grp->name = np->name;
@@ -2330,18 +2506,14 @@
 	/* we do not check return since it's safe node passed down */
 	size /= sizeof(*list);
 	if (!size || size % 4) {
-		dev_err(info->dev, "wrong pins number or pins and configs should be by 4\n");
+		dev_err(dev, "wrong pins number or pins and configs should be by 4\n");
 		return -EINVAL;
 	}
 
 	grp->npins = size / 4;
 
-	grp->pins = devm_kcalloc(info->dev, grp->npins, sizeof(unsigned int),
-						GFP_KERNEL);
-	grp->data = devm_kcalloc(info->dev,
-					grp->npins,
-					sizeof(struct rockchip_pin_config),
-					GFP_KERNEL);
+	grp->pins = devm_kcalloc(dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
+	grp->data = devm_kcalloc(dev, grp->npins, sizeof(*grp->data), GFP_KERNEL);
 	if (!grp->pins || !grp->data)
 		return -ENOMEM;
 
@@ -2364,6 +2536,7 @@
 		np_config = of_find_node_by_phandle(be32_to_cpup(phandle));
 		ret = pinconf_generic_parse_dt_config(np_config, NULL,
 				&grp->data[j].configs, &grp->data[j].nconfigs);
+		of_node_put(np_config);
 		if (ret)
 			return ret;
 	}
@@ -2375,6 +2548,7 @@
 						struct rockchip_pinctrl *info,
 						u32 index)
 {
+	struct device *dev = info->dev;
 	struct device_node *child;
 	struct rockchip_pmx_func *func;
 	struct rockchip_pin_group *grp;
@@ -2382,7 +2556,7 @@
 	static u32 grp_index;
 	u32 i = 0;
 
-	dev_dbg(info->dev, "parse function(%d): %pOFn\n", index, np);
+	dev_dbg(dev, "parse function(%d): %pOFn\n", index, np);
 
 	func = &info->functions[index];
 
@@ -2392,8 +2566,7 @@
 	if (func->ngroups <= 0)
 		return 0;
 
-	func->groups = devm_kcalloc(info->dev,
-			func->ngroups, sizeof(char *), GFP_KERNEL);
+	func->groups = devm_kcalloc(dev, func->ngroups, sizeof(*func->groups), GFP_KERNEL);
 	if (!func->groups)
 		return -ENOMEM;
 
@@ -2421,20 +2594,14 @@
 
 	rockchip_pinctrl_child_count(info, np);
 
-	dev_dbg(&pdev->dev, "nfunctions = %d\n", info->nfunctions);
-	dev_dbg(&pdev->dev, "ngroups = %d\n", info->ngroups);
+	dev_dbg(dev, "nfunctions = %d\n", info->nfunctions);
+	dev_dbg(dev, "ngroups = %d\n", info->ngroups);
 
-	info->functions = devm_kcalloc(dev,
-					      info->nfunctions,
-					      sizeof(struct rockchip_pmx_func),
-					      GFP_KERNEL);
+	info->functions = devm_kcalloc(dev, info->nfunctions, sizeof(*info->functions), GFP_KERNEL);
 	if (!info->functions)
 		return -ENOMEM;
 
-	info->groups = devm_kcalloc(dev,
-					    info->ngroups,
-					    sizeof(struct rockchip_pin_group),
-					    GFP_KERNEL);
+	info->groups = devm_kcalloc(dev, info->ngroups, sizeof(*info->groups), GFP_KERNEL);
 	if (!info->groups)
 		return -ENOMEM;
 
@@ -2446,7 +2613,7 @@
 
 		ret = rockchip_pinctrl_parse_functions(child, info, i++);
 		if (ret) {
-			dev_err(&pdev->dev, "failed to parse function\n");
+			dev_err(dev, "failed to parse function\n");
 			of_node_put(child);
 			return ret;
 		}
@@ -2461,6 +2628,7 @@
 	struct pinctrl_desc *ctrldesc = &info->pctl;
 	struct pinctrl_pin_desc *pindesc, *pdesc;
 	struct rockchip_pin_bank *pin_bank;
+	struct device *dev = &pdev->dev;
 	int pin, bank, ret;
 	int k;
 
@@ -2470,9 +2638,7 @@
 	ctrldesc->pmxops = &rockchip_pmx_ops;
 	ctrldesc->confops = &rockchip_pinconf_ops;
 
-	pindesc = devm_kcalloc(&pdev->dev,
-			       info->ctrl->nr_pins, sizeof(*pindesc),
-			       GFP_KERNEL);
+	pindesc = devm_kcalloc(dev, info->ctrl->nr_pins, sizeof(*pindesc), GFP_KERNEL);
 	if (!pindesc)
 		return -ENOMEM;
 
@@ -2489,7 +2655,7 @@
 			pdesc++;
 		}
 
-		INIT_LIST_HEAD(&pin_bank->deferred_output);
+		INIT_LIST_HEAD(&pin_bank->deferred_pins);
 		mutex_init(&pin_bank->deferred_lock);
 	}
 
@@ -2497,9 +2663,9 @@
 	if (ret)
 		return ret;
 
-	info->pctl_dev = devm_pinctrl_register(&pdev->dev, ctrldesc, info);
+	info->pctl_dev = devm_pinctrl_register(dev, ctrldesc, info);
 	if (IS_ERR(info->pctl_dev)) {
-		dev_err(&pdev->dev, "could not register pinctrl driver\n");
+		dev_err(dev, "could not register pinctrl driver\n");
 		return PTR_ERR(info->pctl_dev);
 	}
 
@@ -2513,8 +2679,9 @@
 						struct rockchip_pinctrl *d,
 						struct platform_device *pdev)
 {
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
 	const struct of_device_id *match;
-	struct device_node *node = pdev->dev.of_node;
 	struct rockchip_pin_ctrl *ctrl;
 	struct rockchip_pin_bank *bank;
 	int grf_offs, pmu_offs, drv_grf_offs, drv_pmu_offs, i, j;
@@ -2566,7 +2733,7 @@
 						drv_pmu_offs : drv_grf_offs;
 			}
 
-			dev_dbg(d->dev, "bank %d, iomux %d has iom_offset 0x%x drv_offset 0x%x\n",
+			dev_dbg(dev, "bank %d, iomux %d has iom_offset 0x%x drv_offset 0x%x\n",
 				i, j, iom->offset, drv->offset);
 
 			/*
@@ -2675,8 +2842,8 @@
 {
 	struct rockchip_pinctrl *info;
 	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node, *node;
 	struct rockchip_pin_ctrl *ctrl;
-	struct device_node *np = pdev->dev.of_node, *node;
 	struct resource *res;
 	void __iomem *base;
 	int ret;
@@ -2702,6 +2869,7 @@
 	node = of_parse_phandle(np, "rockchip,grf", 0);
 	if (node) {
 		info->regmap_base = syscon_node_to_regmap(node);
+		of_node_put(node);
 		if (IS_ERR(info->regmap_base))
 			return PTR_ERR(info->regmap_base);
 	} else {
@@ -2712,8 +2880,8 @@
 
 		rockchip_regmap_config.max_register = resource_size(res) - 4;
 		rockchip_regmap_config.name = "rockchip,pinctrl";
-		info->regmap_base = devm_regmap_init_mmio(&pdev->dev, base,
-						    &rockchip_regmap_config);
+		info->regmap_base =
+			devm_regmap_init_mmio(dev, base, &rockchip_regmap_config);
 
 		/* to check for the old dt-bindings */
 		info->reg_size = resource_size(res);
@@ -2725,12 +2893,10 @@
 			if (IS_ERR(base))
 				return PTR_ERR(base);
 
-			rockchip_regmap_config.max_register =
-							resource_size(res) - 4;
+			rockchip_regmap_config.max_register = resource_size(res) - 4;
 			rockchip_regmap_config.name = "rockchip,pinctrl-pull";
-			info->regmap_pull = devm_regmap_init_mmio(&pdev->dev,
-						    base,
-						    &rockchip_regmap_config);
+			info->regmap_pull =
+				devm_regmap_init_mmio(dev, base, &rockchip_regmap_config);
 		}
 	}
 
@@ -2738,6 +2904,7 @@
 	node = of_parse_phandle(np, "rockchip,pmu", 0);
 	if (node) {
 		info->regmap_pmu = syscon_node_to_regmap(node);
+		of_node_put(node);
 		if (IS_ERR(info->regmap_pmu))
 			return PTR_ERR(info->regmap_pmu);
 	}
@@ -2748,9 +2915,9 @@
 
 	platform_set_drvdata(pdev, info);
 
-	ret = of_platform_populate(np, rockchip_bank_match, NULL, NULL);
+	ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
 	if (ret) {
-		dev_err(&pdev->dev, "failed to register gpio device\n");
+		dev_err(dev, "failed to register gpio device\n");
 		return ret;
 	}
 
@@ -2761,7 +2928,7 @@
 {
 	struct rockchip_pinctrl *info = platform_get_drvdata(pdev);
 	struct rockchip_pin_bank *bank;
-	struct rockchip_pin_output_deferred *cfg;
+	struct rockchip_pin_deferred *cfg;
 	int i;
 
 	of_platform_depopulate(&pdev->dev);
@@ -2770,9 +2937,9 @@
 		bank = &info->ctrl->pin_banks[i];
 
 		mutex_lock(&bank->deferred_lock);
-		while (!list_empty(&bank->deferred_output)) {
-			cfg = list_first_entry(&bank->deferred_output,
-					       struct rockchip_pin_output_deferred, head);
+		while (!list_empty(&bank->deferred_pins)) {
+			cfg = list_first_entry(&bank->deferred_pins,
+					       struct rockchip_pin_deferred, head);
 			list_del(&cfg->head);
 			kfree(cfg);
 		}
@@ -3051,7 +3218,7 @@
 	PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", 0, 0, 0, 0),
 	PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", 0, 0, 0, 0),
 	PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", 0,
-			     IOMUX_WIDTH_3BIT,
+			     IOMUX_WIDTH_2BIT,
 			     IOMUX_WIDTH_3BIT,
 			     0),
 	PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3",
@@ -3065,7 +3232,7 @@
 		.pin_banks		= rk3328_pin_banks,
 		.nr_banks		= ARRAY_SIZE(rk3328_pin_banks),
 		.label			= "RK3328-GPIO",
-		.type			= RK3288,
+		.type			= RK3328,
 		.grf_mux_offset		= 0x0,
 		.iomux_recalced		= rk3328_mux_recalced_data,
 		.niomux_recalced	= ARRAY_SIZE(rk3328_mux_recalced_data),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-rockchip.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-rockchip.h
@@ -27,6 +27,7 @@
 	RK3188,
 	RK3288,
 	RK3308,
+	RK3328,
 	RK3368,
 	RK3399,
 	RK3568,
@@ -171,7 +172,7 @@
 	u32				toggle_edge_mode;
 	u32				recalced_mask;
 	u32				route_mask;
-	struct list_head		deferred_output;
+	struct list_head		deferred_pins;
 	struct mutex			deferred_lock;
 };
 
@@ -230,10 +231,10 @@
 	struct rockchip_mux_route_data *iomux_routes;
 	u32				niomux_routes;
 
-	void	(*pull_calc_reg)(struct rockchip_pin_bank *bank,
+	int	(*pull_calc_reg)(struct rockchip_pin_bank *bank,
 				    int pin_num, struct regmap **regmap,
 				    int *reg, u8 *bit);
-	void	(*drv_calc_reg)(struct rockchip_pin_bank *bank,
+	int	(*drv_calc_reg)(struct rockchip_pin_bank *bank,
 				    int pin_num, struct regmap **regmap,
 				    int *reg, u8 *bit);
 	int	(*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
@@ -247,9 +248,12 @@
 	unsigned int		nconfigs;
 };
 
-struct rockchip_pin_output_deferred {
+enum pin_config_param;
+
+struct rockchip_pin_deferred {
 	struct list_head head;
 	unsigned int pin;
+	enum pin_config_param param;
 	u32 arg;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-single.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-single.c
@@ -350,6 +350,8 @@
 		return -ENOTSUPP;
 	fselector = setting->func;
 	function = pinmux_generic_get_function(pctldev, fselector);
+	if (!function)
+		return -EINVAL;
 	*func = function->data;
 	if (!(*func)) {
 		dev_err(pcs->dev, "%s could not find function%i\n",
@@ -372,6 +374,8 @@
 	if (!pcs->fmask)
 		return 0;
 	function = pinmux_generic_get_function(pctldev, fselector);
+	if (!function)
+		return -EINVAL;
 	func = function->data;
 	if (!func)
 		return -EINVAL;
@@ -727,7 +731,7 @@
 
 	mux_bytes = pcs->width / BITS_PER_BYTE;
 
-	if (pcs->bits_per_mux) {
+	if (pcs->bits_per_mux && pcs->fmask) {
 		pcs->bits_per_pin = fls(pcs->fmask);
 		nr_pins = (pcs->size * BITS_PER_BYTE) / pcs->bits_per_pin;
 	} else {
@@ -1326,7 +1330,6 @@
 static void pcs_free_resources(struct pcs_device *pcs)
 {
 	pcs_irq_free(pcs);
-	pinctrl_unregister(pcs->pctl);
 
 #if IS_BUILTIN(CONFIG_PINCTRL_SINGLE)
 	if (pcs->missing_nr_pinctrl_cells)
@@ -1883,7 +1886,7 @@
 	if (ret < 0)
 		goto free;
 
-	ret = pinctrl_register_and_init(&pcs->desc, pcs->dev, pcs, &pcs->pctl);
+	ret = devm_pinctrl_register_and_init(pcs->dev, &pcs->desc, pcs, &pcs->pctl);
 	if (ret) {
 		dev_err(pcs->dev, "could not register single pinctrl driver\n");
 		goto free;
@@ -1916,8 +1919,11 @@
 
 	dev_info(pcs->dev, "%i pins, size %u\n", pcs->desc.npins, pcs->size);
 
-	return pinctrl_enable(pcs->pctl);
+	ret = pinctrl_enable(pcs->pctl);
+	if (ret)
+		goto free;
 
+	return 0;
 free:
 	pcs_free_resources(pcs);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-zynq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-zynq.c
@@ -8,6 +8,7 @@
  */
 #include <linux/io.h>
 #include <linux/mfd/syscon.h>
+#include <linux/module.h>
 #include <linux/init.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
@@ -1210,8 +1211,4 @@
 	.probe = zynq_pinctrl_probe,
 };
 
-static int __init zynq_pinctrl_init(void)
-{
-	return platform_driver_register(&zynq_pinctrl_driver);
-}
-arch_initcall(zynq_pinctrl_init);
+module_platform_driver(zynq_pinctrl_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/pinctrl-zynqmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/pinctrl-zynqmp.c
@@ -45,7 +45,6 @@
  * @name:	Name of the pin mux function
  * @groups:	List of pin groups for this function
  * @ngroups:	Number of entries in @groups
- * @node:	Firmware node matching with the function
  *
  * This structure holds information about pin control function
  * and function group names supporting that function.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/Kconfig
@@ -189,6 +189,7 @@
 	select PINMUX
 	select PINCONF
 	select GENERIC_PINCONF
+  select GPIOLIB
 	select GPIOLIB_IRQCHIP
 	select IRQ_DOMAIN_HIERARCHY
 	help
@@ -203,6 +204,7 @@
 	select PINMUX
 	select PINCONF
 	select GENERIC_PINCONF
+  select GPIOLIB
 	select GPIOLIB_IRQCHIP
 	select IRQ_DOMAIN_HIERARCHY
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-lpass-lpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-lpass-lpi.c
@@ -102,7 +102,8 @@
 	char __iomem *tlmm_base;
 	char __iomem *slew_base;
 	struct clk_bulk_data clks[MAX_LPI_NUM_CLKS];
-	struct mutex slew_access_lock;
+	/* Protects from concurrent register updates */
+	struct mutex lock;
 	const struct lpi_pinctrl_variant_data *data;
 };
 
@@ -330,9 +331,11 @@
 	if (WARN_ON(i == g->nfuncs))
 		return -EINVAL;
 
+	mutex_lock(&pctrl->lock);
 	val = lpi_gpio_read(pctrl, pin, LPI_GPIO_CFG_REG);
 	u32p_replace_bits(&val, i, LPI_GPIO_FUNCTION_MASK);
 	lpi_gpio_write(pctrl, pin, LPI_GPIO_CFG_REG, val);
+	mutex_unlock(&pctrl->lock);
 
 	return 0;
 }
@@ -438,20 +441,30 @@
 			if (slew_offset == NO_SLEW)
 				break;
 
-			mutex_lock(&pctrl->slew_access_lock);
+			mutex_lock(&pctrl->lock);
 
 			sval = ioread32(pctrl->slew_base + LPI_SLEW_RATE_CTL_REG);
 			sval &= ~(LPI_SLEW_RATE_MASK << slew_offset);
 			sval |= arg << slew_offset;
 			iowrite32(sval, pctrl->slew_base + LPI_SLEW_RATE_CTL_REG);
 
-			mutex_unlock(&pctrl->slew_access_lock);
+			mutex_unlock(&pctrl->lock);
 			break;
 		default:
 			return -EINVAL;
 		}
 	}
 
+	/*
+	 * As per Hardware Programming Guide, when configuring pin as output,
+	 * set the pin value before setting output-enable (OE).
+	 */
+	if (output_enabled) {
+		val = u32_encode_bits(value ? 1 : 0, LPI_GPIO_VALUE_OUT_MASK);
+		lpi_gpio_write(pctrl, group, LPI_GPIO_VALUE_REG, val);
+	}
+
+	mutex_lock(&pctrl->lock);
 	val = lpi_gpio_read(pctrl, group, LPI_GPIO_CFG_REG);
 
 	u32p_replace_bits(&val, pullup, LPI_GPIO_PULL_MASK);
@@ -460,11 +473,7 @@
 	u32p_replace_bits(&val, output_enabled, LPI_GPIO_OE_MASK);
 
 	lpi_gpio_write(pctrl, group, LPI_GPIO_CFG_REG, val);
-
-	if (output_enabled) {
-		val = u32_encode_bits(value ? 1 : 0, LPI_GPIO_VALUE_OUT_MASK);
-		lpi_gpio_write(pctrl, group, LPI_GPIO_VALUE_REG, val);
-	}
+	mutex_unlock(&pctrl->lock);
 
 	return 0;
 }
@@ -638,7 +647,7 @@
 	pctrl->chip.of_gpio_n_cells = 2;
 	pctrl->chip.can_sleep = false;
 
-	mutex_init(&pctrl->slew_access_lock);
+	mutex_init(&pctrl->lock);
 
 	pctrl->ctrl = devm_pinctrl_register(dev, &pctrl->desc, pctrl);
 	if (IS_ERR(pctrl->ctrl)) {
@@ -656,7 +665,7 @@
 	return 0;
 
 err_pinctrl:
-	mutex_destroy(&pctrl->slew_access_lock);
+	mutex_destroy(&pctrl->lock);
 	clk_bulk_disable_unprepare(MAX_LPI_NUM_CLKS, pctrl->clks);
 
 	return ret;
@@ -666,7 +675,7 @@
 {
 	struct lpi_pinctrl *pctrl = platform_get_drvdata(pdev);
 
-	mutex_destroy(&pctrl->slew_access_lock);
+	mutex_destroy(&pctrl->lock);
 	clk_bulk_disable_unprepare(MAX_LPI_NUM_CLKS, pctrl->clks);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-msm8916.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-msm8916.c
@@ -844,8 +844,8 @@
 	PINGROUP(28, pwr_modem_enabled_a, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, atest_combodac),
 	PINGROUP(29, cci_i2c, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, atest_combodac),
 	PINGROUP(30, cci_i2c, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
-	PINGROUP(31, cci_timer0, NA, NA, NA, NA, NA, NA, NA, NA),
-	PINGROUP(32, cci_timer1, NA, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(31, cci_timer0, flash_strobe, NA, NA, NA, NA, NA, NA, NA),
+	PINGROUP(32, cci_timer1, flash_strobe, NA, NA, NA, NA, NA, NA, NA),
 	PINGROUP(33, cci_async, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
 	PINGROUP(34, pwr_nav_enabled_a, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
 	PINGROUP(35, pwr_crypto_enabled_a, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-msm8976.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-msm8976.c
@@ -733,7 +733,7 @@
 	"gpio74",
 };
 static const char * const wcss_bt_groups[] = {
-	"gpio39", "gpio47", "gpio88",
+	"gpio39", "gpio47", "gpio48",
 };
 static const char * const sdc3_groups[] = {
 	"gpio39", "gpio40", "gpio41",
@@ -958,9 +958,9 @@
 	PINGROUP(37, NA, NA, NA, qdss_tracedata_b, NA, NA, NA, NA, NA),
 	PINGROUP(38, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b, NA),
 	PINGROUP(39, wcss_bt, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
-	PINGROUP(40, wcss_wlan, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
-	PINGROUP(41, wcss_wlan, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
-	PINGROUP(42, wcss_wlan, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+	PINGROUP(40, wcss_wlan2, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+	PINGROUP(41, wcss_wlan1, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+	PINGROUP(42, wcss_wlan0, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
 	PINGROUP(43, wcss_wlan, sdc3, NA, NA, qdss_tracedata_a, NA, NA, NA, NA),
 	PINGROUP(44, wcss_wlan, sdc3, NA, NA, NA, NA, NA, NA, NA),
 	PINGROUP(45, wcss_fm, NA, qdss_tracectl_a, NA, NA, NA, NA, NA, NA),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-sc8180x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-sc8180x.c
@@ -530,10 +530,10 @@
 DECLARE_MSM_GPIO_PINS(188);
 DECLARE_MSM_GPIO_PINS(189);
 
-static const unsigned int sdc2_clk_pins[] = { 190 };
-static const unsigned int sdc2_cmd_pins[] = { 191 };
-static const unsigned int sdc2_data_pins[] = { 192 };
-static const unsigned int ufs_reset_pins[] = { 193 };
+static const unsigned int ufs_reset_pins[] = { 190 };
+static const unsigned int sdc2_clk_pins[] = { 191 };
+static const unsigned int sdc2_cmd_pins[] = { 192 };
+static const unsigned int sdc2_data_pins[] = { 193 };
 
 enum sc8180x_functions {
 	msm_mux_adsp_ext,
@@ -1582,7 +1582,7 @@
 static const struct msm_gpio_wakeirq_map sc8180x_pdc_map[] = {
 	{ 3, 31 }, { 5, 32 }, { 8, 33 }, { 9, 34 }, { 10, 100 }, { 12, 104 },
 	{ 24, 37 }, { 26, 38 }, { 27, 41 }, { 28, 42 }, { 30, 39 }, { 36, 43 },
-	{ 37, 43 }, { 38, 45 }, { 39, 118 }, { 39, 125 }, { 41, 47 },
+	{ 37, 44 }, { 38, 45 }, { 39, 118 }, { 39, 125 }, { 41, 47 },
 	{ 42, 48 }, { 46, 50 }, { 47, 49 }, { 48, 51 }, { 49, 53 }, { 50, 52 },
 	{ 51, 116 }, { 51, 123 }, { 53, 54 }, { 54, 55 }, { 55, 56 },
 	{ 56, 57 }, { 58, 58 }, { 60, 60 }, { 68, 62 }, { 70, 63 }, { 76, 86 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-sdm845.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-sdm845.c
@@ -1310,6 +1310,7 @@
 	.ngpios = 151,
 	.wakeirq_map = sdm845_pdc_map,
 	.nwakeirq_map = ARRAY_SIZE(sdm845_pdc_map),
+	.wakeirq_dual_edge_errata = true,
 };
 
 static const struct msm_pinctrl_soc_data sdm845_acpi_pinctrl = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-sm8250.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-sm8250.c
@@ -1316,7 +1316,7 @@
 static const struct msm_gpio_wakeirq_map sm8250_pdc_map[] = {
 	{ 0, 79 }, { 1, 84 }, { 2, 80 }, { 3, 82 }, { 4, 107 }, { 7, 43 },
 	{ 11, 42 }, { 14, 44 }, { 15, 52 }, { 19, 67 }, { 23, 68 }, { 24, 105 },
-	{ 27, 92 }, { 28, 106 }, { 31, 69 }, { 35, 70 }, { 39, 37 },
+	{ 27, 92 }, { 28, 106 }, { 31, 69 }, { 35, 70 }, { 39, 73 },
 	{ 40, 108 }, { 43, 71 }, { 45, 72 }, { 47, 83 }, { 51, 74 }, { 55, 77 },
 	{ 59, 78 }, { 63, 75 }, { 64, 81 }, { 65, 87 }, { 66, 88 }, { 67, 89 },
 	{ 68, 54 }, { 70, 85 }, { 77, 46 }, { 80, 90 }, { 81, 91 }, { 83, 97 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-sm8350.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-sm8350.c
@@ -1597,10 +1597,10 @@
 	[200] = PINGROUP(200, qdss_gpio, _, _, _, _, _, _, _, _),
 	[201] = PINGROUP(201, _, _, _, _, _, _, _, _, _),
 	[202] = PINGROUP(202, _, _, _, _, _, _, _, _, _),
-	[203] = UFS_RESET(ufs_reset, 0x1d8000),
-	[204] = SDC_PINGROUP(sdc2_clk, 0x1cf000, 14, 6),
-	[205] = SDC_PINGROUP(sdc2_cmd, 0x1cf000, 11, 3),
-	[206] = SDC_PINGROUP(sdc2_data, 0x1cf000, 9, 0),
+	[203] = UFS_RESET(ufs_reset, 0xd8000),
+	[204] = SDC_PINGROUP(sdc2_clk, 0xcf000, 14, 6),
+	[205] = SDC_PINGROUP(sdc2_cmd, 0xcf000, 11, 3),
+	[206] = SDC_PINGROUP(sdc2_data, 0xcf000, 9, 0),
 };
 
 static const struct msm_gpio_wakeirq_map sm8350_pdc_map[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -1156,6 +1156,8 @@
 	{ .compatible = "qcom,pm8350b-gpio", .data = (void *) 8 },
 	{ .compatible = "qcom,pm8350c-gpio", .data = (void *) 9 },
 	{ .compatible = "qcom,pm8916-gpio", .data = (void *) 4 },
+	/* pm8937 has 8 GPIOs with holes on 3, 4 and 6 */
+	{ .compatible = "qcom,pm8937-gpio", .data = (void *) 8 },
 	{ .compatible = "qcom,pm8941-gpio", .data = (void *) 36 },
 	/* pm8950 has 8 GPIOs with holes on 3 */
 	{ .compatible = "qcom,pm8950-gpio", .data = (void *) 8 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/Kconfig
@@ -3,37 +3,33 @@
         depends on RALINK
 
 config PINCTRL_RALINK
-        bool "Ralink pin control support"
-        default y if RALINK
-
-config PINCTRL_RT2880
-        bool "RT2880 pinctrl driver for RALINK/Mediatek SOCs"
+        bool "Ralink pinctrl driver"
         select PINMUX
         select GENERIC_PINCONF
 
 config PINCTRL_MT7620
         bool "mt7620 pinctrl driver for RALINK/Mediatek SOCs"
         depends on RALINK && SOC_MT7620
-        select PINCTRL_RT2880
+        select PINCTRL_RALINK
 
 config PINCTRL_MT7621
         bool "mt7621 pinctrl driver for RALINK/Mediatek SOCs"
         depends on RALINK && SOC_MT7621
-        select PINCTRL_RT2880
+        select PINCTRL_RALINK
 
 config PINCTRL_RT288X
         bool "RT288X pinctrl driver for RALINK/Mediatek SOCs"
         depends on RALINK && SOC_RT288X
-        select PINCTRL_RT2880
+        select PINCTRL_RALINK
 
 config PINCTRL_RT305X
         bool "RT305X pinctrl driver for RALINK/Mediatek SOCs"
         depends on RALINK && SOC_RT305X
-        select PINCTRL_RT2880
+        select PINCTRL_RALINK
 
 config PINCTRL_RT3883
         bool "RT3883 pinctrl driver for RALINK/Mediatek SOCs"
         depends on RALINK && SOC_RT3883
-        select PINCTRL_RT2880
+        select PINCTRL_RALINK
 
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_PINCTRL_RT2880)   += pinctrl-rt2880.o
+obj-$(CONFIG_PINCTRL_RALINK)   += pinctrl-ralink.o
 
 obj-$(CONFIG_PINCTRL_MT7620)   += pinctrl-mt7620.o
 obj-$(CONFIG_PINCTRL_MT7621)   += pinctrl-mt7621.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-mt7620.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-mt7620.c
@@ -1,10 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0-only
 
+#include <asm/mach-ralink/ralink_regs.h>
 #include <asm/mach-ralink/mt7620.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
-#include "pinmux.h"
+#include "pinctrl-ralink.h"
 
 #define MT7620_GPIO_MODE_UART0_SHIFT	2
 #define MT7620_GPIO_MODE_UART0_MASK	0x7
@@ -53,20 +54,20 @@
 #define MT7620_GPIO_MODE_EPHY		15
 #define MT7620_GPIO_MODE_PA		20
 
-static struct rt2880_pmx_func i2c_grp[] =  { FUNC("i2c", 0, 1, 2) };
-static struct rt2880_pmx_func spi_grp[] = { FUNC("spi", 0, 3, 4) };
-static struct rt2880_pmx_func uartlite_grp[] = { FUNC("uartlite", 0, 15, 2) };
-static struct rt2880_pmx_func mdio_grp[] = {
+static struct ralink_pmx_func i2c_grp[] =  { FUNC("i2c", 0, 1, 2) };
+static struct ralink_pmx_func spi_grp[] = { FUNC("spi", 0, 3, 4) };
+static struct ralink_pmx_func uartlite_grp[] = { FUNC("uartlite", 0, 15, 2) };
+static struct ralink_pmx_func mdio_grp[] = {
 	FUNC("mdio", MT7620_GPIO_MODE_MDIO, 22, 2),
 	FUNC("refclk", MT7620_GPIO_MODE_MDIO_REFCLK, 22, 2),
 };
-static struct rt2880_pmx_func rgmii1_grp[] = { FUNC("rgmii1", 0, 24, 12) };
-static struct rt2880_pmx_func refclk_grp[] = { FUNC("spi refclk", 0, 37, 3) };
-static struct rt2880_pmx_func ephy_grp[] = { FUNC("ephy", 0, 40, 5) };
-static struct rt2880_pmx_func rgmii2_grp[] = { FUNC("rgmii2", 0, 60, 12) };
-static struct rt2880_pmx_func wled_grp[] = { FUNC("wled", 0, 72, 1) };
-static struct rt2880_pmx_func pa_grp[] = { FUNC("pa", 0, 18, 4) };
-static struct rt2880_pmx_func uartf_grp[] = {
+static struct ralink_pmx_func rgmii1_grp[] = { FUNC("rgmii1", 0, 24, 12) };
+static struct ralink_pmx_func refclk_grp[] = { FUNC("spi refclk", 0, 37, 3) };
+static struct ralink_pmx_func ephy_grp[] = { FUNC("ephy", 0, 40, 5) };
+static struct ralink_pmx_func rgmii2_grp[] = { FUNC("rgmii2", 0, 60, 12) };
+static struct ralink_pmx_func wled_grp[] = { FUNC("wled", 0, 72, 1) };
+static struct ralink_pmx_func pa_grp[] = { FUNC("pa", 0, 18, 4) };
+static struct ralink_pmx_func uartf_grp[] = {
 	FUNC("uartf", MT7620_GPIO_MODE_UARTF, 7, 8),
 	FUNC("pcm uartf", MT7620_GPIO_MODE_PCM_UARTF, 7, 8),
 	FUNC("pcm i2s", MT7620_GPIO_MODE_PCM_I2S, 7, 8),
@@ -75,20 +76,20 @@
 	FUNC("gpio uartf", MT7620_GPIO_MODE_GPIO_UARTF, 7, 4),
 	FUNC("gpio i2s", MT7620_GPIO_MODE_GPIO_I2S, 7, 4),
 };
-static struct rt2880_pmx_func wdt_grp[] = {
+static struct ralink_pmx_func wdt_grp[] = {
 	FUNC("wdt rst", 0, 17, 1),
 	FUNC("wdt refclk", 0, 17, 1),
 	};
-static struct rt2880_pmx_func pcie_rst_grp[] = {
+static struct ralink_pmx_func pcie_rst_grp[] = {
 	FUNC("pcie rst", MT7620_GPIO_MODE_PCIE_RST, 36, 1),
 	FUNC("pcie refclk", MT7620_GPIO_MODE_PCIE_REF, 36, 1)
 };
-static struct rt2880_pmx_func nd_sd_grp[] = {
+static struct ralink_pmx_func nd_sd_grp[] = {
 	FUNC("nand", MT7620_GPIO_MODE_NAND, 45, 15),
 	FUNC("sd", MT7620_GPIO_MODE_SD, 47, 13)
 };
 
-static struct rt2880_pmx_group mt7620a_pinmux_data[] = {
+static struct ralink_pmx_group mt7620a_pinmux_data[] = {
 	GRP("i2c", i2c_grp, 1, MT7620_GPIO_MODE_I2C),
 	GRP("uartf", uartf_grp, MT7620_GPIO_MODE_UART0_MASK,
 		MT7620_GPIO_MODE_UART0_SHIFT),
@@ -111,262 +112,262 @@
 	{ 0 }
 };
 
-static struct rt2880_pmx_func pwm1_grp_mt7628[] = {
+static struct ralink_pmx_func pwm1_grp_mt76x8[] = {
 	FUNC("sdxc d6", 3, 19, 1),
 	FUNC("utif", 2, 19, 1),
 	FUNC("gpio", 1, 19, 1),
 	FUNC("pwm1", 0, 19, 1),
 };
 
-static struct rt2880_pmx_func pwm0_grp_mt7628[] = {
+static struct ralink_pmx_func pwm0_grp_mt76x8[] = {
 	FUNC("sdxc d7", 3, 18, 1),
 	FUNC("utif", 2, 18, 1),
 	FUNC("gpio", 1, 18, 1),
 	FUNC("pwm0", 0, 18, 1),
 };
 
-static struct rt2880_pmx_func uart2_grp_mt7628[] = {
+static struct ralink_pmx_func uart2_grp_mt76x8[] = {
 	FUNC("sdxc d5 d4", 3, 20, 2),
 	FUNC("pwm", 2, 20, 2),
 	FUNC("gpio", 1, 20, 2),
 	FUNC("uart2", 0, 20, 2),
 };
 
-static struct rt2880_pmx_func uart1_grp_mt7628[] = {
+static struct ralink_pmx_func uart1_grp_mt76x8[] = {
 	FUNC("sw_r", 3, 45, 2),
 	FUNC("pwm", 2, 45, 2),
 	FUNC("gpio", 1, 45, 2),
 	FUNC("uart1", 0, 45, 2),
 };
 
-static struct rt2880_pmx_func i2c_grp_mt7628[] = {
+static struct ralink_pmx_func i2c_grp_mt76x8[] = {
 	FUNC("-", 3, 4, 2),
 	FUNC("debug", 2, 4, 2),
 	FUNC("gpio", 1, 4, 2),
 	FUNC("i2c", 0, 4, 2),
 };
 
-static struct rt2880_pmx_func refclk_grp_mt7628[] = { FUNC("refclk", 0, 37, 1) };
-static struct rt2880_pmx_func perst_grp_mt7628[] = { FUNC("perst", 0, 36, 1) };
-static struct rt2880_pmx_func wdt_grp_mt7628[] = { FUNC("wdt", 0, 38, 1) };
-static struct rt2880_pmx_func spi_grp_mt7628[] = { FUNC("spi", 0, 7, 4) };
+static struct ralink_pmx_func refclk_grp_mt76x8[] = { FUNC("refclk", 0, 37, 1) };
+static struct ralink_pmx_func perst_grp_mt76x8[] = { FUNC("perst", 0, 36, 1) };
+static struct ralink_pmx_func wdt_grp_mt76x8[] = { FUNC("wdt", 0, 38, 1) };
+static struct ralink_pmx_func spi_grp_mt76x8[] = { FUNC("spi", 0, 7, 4) };
 
-static struct rt2880_pmx_func sd_mode_grp_mt7628[] = {
+static struct ralink_pmx_func sd_mode_grp_mt76x8[] = {
 	FUNC("jtag", 3, 22, 8),
 	FUNC("utif", 2, 22, 8),
 	FUNC("gpio", 1, 22, 8),
 	FUNC("sdxc", 0, 22, 8),
 };
 
-static struct rt2880_pmx_func uart0_grp_mt7628[] = {
+static struct ralink_pmx_func uart0_grp_mt76x8[] = {
 	FUNC("-", 3, 12, 2),
 	FUNC("-", 2, 12, 2),
 	FUNC("gpio", 1, 12, 2),
 	FUNC("uart0", 0, 12, 2),
 };
 
-static struct rt2880_pmx_func i2s_grp_mt7628[] = {
+static struct ralink_pmx_func i2s_grp_mt76x8[] = {
 	FUNC("antenna", 3, 0, 4),
 	FUNC("pcm", 2, 0, 4),
 	FUNC("gpio", 1, 0, 4),
 	FUNC("i2s", 0, 0, 4),
 };
 
-static struct rt2880_pmx_func spi_cs1_grp_mt7628[] = {
+static struct ralink_pmx_func spi_cs1_grp_mt76x8[] = {
 	FUNC("-", 3, 6, 1),
 	FUNC("refclk", 2, 6, 1),
 	FUNC("gpio", 1, 6, 1),
 	FUNC("spi cs1", 0, 6, 1),
 };
 
-static struct rt2880_pmx_func spis_grp_mt7628[] = {
+static struct ralink_pmx_func spis_grp_mt76x8[] = {
 	FUNC("pwm_uart2", 3, 14, 4),
 	FUNC("utif", 2, 14, 4),
 	FUNC("gpio", 1, 14, 4),
 	FUNC("spis", 0, 14, 4),
 };
 
-static struct rt2880_pmx_func gpio_grp_mt7628[] = {
+static struct ralink_pmx_func gpio_grp_mt76x8[] = {
 	FUNC("pcie", 3, 11, 1),
 	FUNC("refclk", 2, 11, 1),
 	FUNC("gpio", 1, 11, 1),
 	FUNC("gpio", 0, 11, 1),
 };
 
-static struct rt2880_pmx_func p4led_kn_grp_mt7628[] = {
+static struct ralink_pmx_func p4led_kn_grp_mt76x8[] = {
 	FUNC("jtag", 3, 30, 1),
 	FUNC("utif", 2, 30, 1),
 	FUNC("gpio", 1, 30, 1),
 	FUNC("p4led_kn", 0, 30, 1),
 };
 
-static struct rt2880_pmx_func p3led_kn_grp_mt7628[] = {
+static struct ralink_pmx_func p3led_kn_grp_mt76x8[] = {
 	FUNC("jtag", 3, 31, 1),
 	FUNC("utif", 2, 31, 1),
 	FUNC("gpio", 1, 31, 1),
 	FUNC("p3led_kn", 0, 31, 1),
 };
 
-static struct rt2880_pmx_func p2led_kn_grp_mt7628[] = {
+static struct ralink_pmx_func p2led_kn_grp_mt76x8[] = {
 	FUNC("jtag", 3, 32, 1),
 	FUNC("utif", 2, 32, 1),
 	FUNC("gpio", 1, 32, 1),
 	FUNC("p2led_kn", 0, 32, 1),
 };
 
-static struct rt2880_pmx_func p1led_kn_grp_mt7628[] = {
+static struct ralink_pmx_func p1led_kn_grp_mt76x8[] = {
 	FUNC("jtag", 3, 33, 1),
 	FUNC("utif", 2, 33, 1),
 	FUNC("gpio", 1, 33, 1),
 	FUNC("p1led_kn", 0, 33, 1),
 };
 
-static struct rt2880_pmx_func p0led_kn_grp_mt7628[] = {
+static struct ralink_pmx_func p0led_kn_grp_mt76x8[] = {
 	FUNC("jtag", 3, 34, 1),
 	FUNC("rsvd", 2, 34, 1),
 	FUNC("gpio", 1, 34, 1),
 	FUNC("p0led_kn", 0, 34, 1),
 };
 
-static struct rt2880_pmx_func wled_kn_grp_mt7628[] = {
+static struct ralink_pmx_func wled_kn_grp_mt76x8[] = {
 	FUNC("rsvd", 3, 35, 1),
 	FUNC("rsvd", 2, 35, 1),
 	FUNC("gpio", 1, 35, 1),
 	FUNC("wled_kn", 0, 35, 1),
 };
 
-static struct rt2880_pmx_func p4led_an_grp_mt7628[] = {
+static struct ralink_pmx_func p4led_an_grp_mt76x8[] = {
 	FUNC("jtag", 3, 39, 1),
 	FUNC("utif", 2, 39, 1),
 	FUNC("gpio", 1, 39, 1),
 	FUNC("p4led_an", 0, 39, 1),
 };
 
-static struct rt2880_pmx_func p3led_an_grp_mt7628[] = {
+static struct ralink_pmx_func p3led_an_grp_mt76x8[] = {
 	FUNC("jtag", 3, 40, 1),
 	FUNC("utif", 2, 40, 1),
 	FUNC("gpio", 1, 40, 1),
 	FUNC("p3led_an", 0, 40, 1),
 };
 
-static struct rt2880_pmx_func p2led_an_grp_mt7628[] = {
+static struct ralink_pmx_func p2led_an_grp_mt76x8[] = {
 	FUNC("jtag", 3, 41, 1),
 	FUNC("utif", 2, 41, 1),
 	FUNC("gpio", 1, 41, 1),
 	FUNC("p2led_an", 0, 41, 1),
 };
 
-static struct rt2880_pmx_func p1led_an_grp_mt7628[] = {
+static struct ralink_pmx_func p1led_an_grp_mt76x8[] = {
 	FUNC("jtag", 3, 42, 1),
 	FUNC("utif", 2, 42, 1),
 	FUNC("gpio", 1, 42, 1),
 	FUNC("p1led_an", 0, 42, 1),
 };
 
-static struct rt2880_pmx_func p0led_an_grp_mt7628[] = {
+static struct ralink_pmx_func p0led_an_grp_mt76x8[] = {
 	FUNC("jtag", 3, 43, 1),
 	FUNC("rsvd", 2, 43, 1),
 	FUNC("gpio", 1, 43, 1),
 	FUNC("p0led_an", 0, 43, 1),
 };
 
-static struct rt2880_pmx_func wled_an_grp_mt7628[] = {
+static struct ralink_pmx_func wled_an_grp_mt76x8[] = {
 	FUNC("rsvd", 3, 44, 1),
 	FUNC("rsvd", 2, 44, 1),
 	FUNC("gpio", 1, 44, 1),
 	FUNC("wled_an", 0, 44, 1),
 };
 
-#define MT7628_GPIO_MODE_MASK		0x3
+#define MT76X8_GPIO_MODE_MASK		0x3
 
-#define MT7628_GPIO_MODE_P4LED_KN	58
-#define MT7628_GPIO_MODE_P3LED_KN	56
-#define MT7628_GPIO_MODE_P2LED_KN	54
-#define MT7628_GPIO_MODE_P1LED_KN	52
-#define MT7628_GPIO_MODE_P0LED_KN	50
-#define MT7628_GPIO_MODE_WLED_KN	48
-#define MT7628_GPIO_MODE_P4LED_AN	42
-#define MT7628_GPIO_MODE_P3LED_AN	40
-#define MT7628_GPIO_MODE_P2LED_AN	38
-#define MT7628_GPIO_MODE_P1LED_AN	36
-#define MT7628_GPIO_MODE_P0LED_AN	34
-#define MT7628_GPIO_MODE_WLED_AN	32
-#define MT7628_GPIO_MODE_PWM1		30
-#define MT7628_GPIO_MODE_PWM0		28
-#define MT7628_GPIO_MODE_UART2		26
-#define MT7628_GPIO_MODE_UART1		24
-#define MT7628_GPIO_MODE_I2C		20
-#define MT7628_GPIO_MODE_REFCLK		18
-#define MT7628_GPIO_MODE_PERST		16
-#define MT7628_GPIO_MODE_WDT		14
-#define MT7628_GPIO_MODE_SPI		12
-#define MT7628_GPIO_MODE_SDMODE		10
-#define MT7628_GPIO_MODE_UART0		8
-#define MT7628_GPIO_MODE_I2S		6
-#define MT7628_GPIO_MODE_CS1		4
-#define MT7628_GPIO_MODE_SPIS		2
-#define MT7628_GPIO_MODE_GPIO		0
-
-static struct rt2880_pmx_group mt7628an_pinmux_data[] = {
-	GRP_G("pwm1", pwm1_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_PWM1),
-	GRP_G("pwm0", pwm0_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_PWM0),
-	GRP_G("uart2", uart2_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_UART2),
-	GRP_G("uart1", uart1_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_UART1),
-	GRP_G("i2c", i2c_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_I2C),
-	GRP("refclk", refclk_grp_mt7628, 1, MT7628_GPIO_MODE_REFCLK),
-	GRP("perst", perst_grp_mt7628, 1, MT7628_GPIO_MODE_PERST),
-	GRP("wdt", wdt_grp_mt7628, 1, MT7628_GPIO_MODE_WDT),
-	GRP("spi", spi_grp_mt7628, 1, MT7628_GPIO_MODE_SPI),
-	GRP_G("sdmode", sd_mode_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_SDMODE),
-	GRP_G("uart0", uart0_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_UART0),
-	GRP_G("i2s", i2s_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_I2S),
-	GRP_G("spi cs1", spi_cs1_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_CS1),
-	GRP_G("spis", spis_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_SPIS),
-	GRP_G("gpio", gpio_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_GPIO),
-	GRP_G("wled_an", wled_an_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_WLED_AN),
-	GRP_G("p0led_an", p0led_an_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P0LED_AN),
-	GRP_G("p1led_an", p1led_an_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P1LED_AN),
-	GRP_G("p2led_an", p2led_an_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P2LED_AN),
-	GRP_G("p3led_an", p3led_an_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P3LED_AN),
-	GRP_G("p4led_an", p4led_an_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P4LED_AN),
-	GRP_G("wled_kn", wled_kn_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_WLED_KN),
-	GRP_G("p0led_kn", p0led_kn_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P0LED_KN),
-	GRP_G("p1led_kn", p1led_kn_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P1LED_KN),
-	GRP_G("p2led_kn", p2led_kn_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P2LED_KN),
-	GRP_G("p3led_kn", p3led_kn_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P3LED_KN),
-	GRP_G("p4led_kn", p4led_kn_grp_mt7628, MT7628_GPIO_MODE_MASK,
-				1, MT7628_GPIO_MODE_P4LED_KN),
+#define MT76X8_GPIO_MODE_P4LED_KN	58
+#define MT76X8_GPIO_MODE_P3LED_KN	56
+#define MT76X8_GPIO_MODE_P2LED_KN	54
+#define MT76X8_GPIO_MODE_P1LED_KN	52
+#define MT76X8_GPIO_MODE_P0LED_KN	50
+#define MT76X8_GPIO_MODE_WLED_KN	48
+#define MT76X8_GPIO_MODE_P4LED_AN	42
+#define MT76X8_GPIO_MODE_P3LED_AN	40
+#define MT76X8_GPIO_MODE_P2LED_AN	38
+#define MT76X8_GPIO_MODE_P1LED_AN	36
+#define MT76X8_GPIO_MODE_P0LED_AN	34
+#define MT76X8_GPIO_MODE_WLED_AN	32
+#define MT76X8_GPIO_MODE_PWM1		30
+#define MT76X8_GPIO_MODE_PWM0		28
+#define MT76X8_GPIO_MODE_UART2		26
+#define MT76X8_GPIO_MODE_UART1		24
+#define MT76X8_GPIO_MODE_I2C		20
+#define MT76X8_GPIO_MODE_REFCLK		18
+#define MT76X8_GPIO_MODE_PERST		16
+#define MT76X8_GPIO_MODE_WDT		14
+#define MT76X8_GPIO_MODE_SPI		12
+#define MT76X8_GPIO_MODE_SDMODE		10
+#define MT76X8_GPIO_MODE_UART0		8
+#define MT76X8_GPIO_MODE_I2S		6
+#define MT76X8_GPIO_MODE_CS1		4
+#define MT76X8_GPIO_MODE_SPIS		2
+#define MT76X8_GPIO_MODE_GPIO		0
+
+static struct ralink_pmx_group mt76x8_pinmux_data[] = {
+	GRP_G("pwm1", pwm1_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_PWM1),
+	GRP_G("pwm0", pwm0_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_PWM0),
+	GRP_G("uart2", uart2_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_UART2),
+	GRP_G("uart1", uart1_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_UART1),
+	GRP_G("i2c", i2c_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_I2C),
+	GRP("refclk", refclk_grp_mt76x8, 1, MT76X8_GPIO_MODE_REFCLK),
+	GRP("perst", perst_grp_mt76x8, 1, MT76X8_GPIO_MODE_PERST),
+	GRP("wdt", wdt_grp_mt76x8, 1, MT76X8_GPIO_MODE_WDT),
+	GRP("spi", spi_grp_mt76x8, 1, MT76X8_GPIO_MODE_SPI),
+	GRP_G("sdmode", sd_mode_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_SDMODE),
+	GRP_G("uart0", uart0_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_UART0),
+	GRP_G("i2s", i2s_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_I2S),
+	GRP_G("spi cs1", spi_cs1_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_CS1),
+	GRP_G("spis", spis_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_SPIS),
+	GRP_G("gpio", gpio_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_GPIO),
+	GRP_G("wled_an", wled_an_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_WLED_AN),
+	GRP_G("p0led_an", p0led_an_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P0LED_AN),
+	GRP_G("p1led_an", p1led_an_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P1LED_AN),
+	GRP_G("p2led_an", p2led_an_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P2LED_AN),
+	GRP_G("p3led_an", p3led_an_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P3LED_AN),
+	GRP_G("p4led_an", p4led_an_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P4LED_AN),
+	GRP_G("wled_kn", wled_kn_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_WLED_KN),
+	GRP_G("p0led_kn", p0led_kn_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P0LED_KN),
+	GRP_G("p1led_kn", p1led_kn_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P1LED_KN),
+	GRP_G("p2led_kn", p2led_kn_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P2LED_KN),
+	GRP_G("p3led_kn", p3led_kn_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P3LED_KN),
+	GRP_G("p4led_kn", p4led_kn_grp_mt76x8, MT76X8_GPIO_MODE_MASK,
+				1, MT76X8_GPIO_MODE_P4LED_KN),
 	{ 0 }
 };
 
 static int mt7620_pinmux_probe(struct platform_device *pdev)
 {
 	if (is_mt76x8())
-		return rt2880_pinmux_init(pdev, mt7628an_pinmux_data);
+		return ralink_pinmux_init(pdev, mt76x8_pinmux_data);
 	else
-		return rt2880_pinmux_init(pdev, mt7620a_pinmux_data);
+		return ralink_pinmux_init(pdev, mt7620a_pinmux_data);
 }
 
 static const struct of_device_id mt7620_pinmux_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-mt7621.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-mt7621.c
@@ -3,7 +3,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
-#include "pinmux.h"
+#include "pinctrl-ralink.h"
 
 #define MT7621_GPIO_MODE_UART1		1
 #define MT7621_GPIO_MODE_I2C		2
@@ -34,40 +34,40 @@
 #define MT7621_GPIO_MODE_SDHCI_SHIFT	18
 #define MT7621_GPIO_MODE_SDHCI_GPIO	1
 
-static struct rt2880_pmx_func uart1_grp[] =  { FUNC("uart1", 0, 1, 2) };
-static struct rt2880_pmx_func i2c_grp[] =  { FUNC("i2c", 0, 3, 2) };
-static struct rt2880_pmx_func uart3_grp[] = {
+static struct ralink_pmx_func uart1_grp[] =  { FUNC("uart1", 0, 1, 2) };
+static struct ralink_pmx_func i2c_grp[] =  { FUNC("i2c", 0, 3, 2) };
+static struct ralink_pmx_func uart3_grp[] = {
 	FUNC("uart3", 0, 5, 4),
 	FUNC("i2s", 2, 5, 4),
 	FUNC("spdif3", 3, 5, 4),
 };
-static struct rt2880_pmx_func uart2_grp[] = {
+static struct ralink_pmx_func uart2_grp[] = {
 	FUNC("uart2", 0, 9, 4),
 	FUNC("pcm", 2, 9, 4),
 	FUNC("spdif2", 3, 9, 4),
 };
-static struct rt2880_pmx_func jtag_grp[] = { FUNC("jtag", 0, 13, 5) };
-static struct rt2880_pmx_func wdt_grp[] = {
+static struct ralink_pmx_func jtag_grp[] = { FUNC("jtag", 0, 13, 5) };
+static struct ralink_pmx_func wdt_grp[] = {
 	FUNC("wdt rst", 0, 18, 1),
 	FUNC("wdt refclk", 2, 18, 1),
 };
-static struct rt2880_pmx_func pcie_rst_grp[] = {
+static struct ralink_pmx_func pcie_rst_grp[] = {
 	FUNC("pcie rst", MT7621_GPIO_MODE_PCIE_RST, 19, 1),
 	FUNC("pcie refclk", MT7621_GPIO_MODE_PCIE_REF, 19, 1)
 };
-static struct rt2880_pmx_func mdio_grp[] = { FUNC("mdio", 0, 20, 2) };
-static struct rt2880_pmx_func rgmii2_grp[] = { FUNC("rgmii2", 0, 22, 12) };
-static struct rt2880_pmx_func spi_grp[] = {
+static struct ralink_pmx_func mdio_grp[] = { FUNC("mdio", 0, 20, 2) };
+static struct ralink_pmx_func rgmii2_grp[] = { FUNC("rgmii2", 0, 22, 12) };
+static struct ralink_pmx_func spi_grp[] = {
 	FUNC("spi", 0, 34, 7),
 	FUNC("nand1", 2, 34, 7),
 };
-static struct rt2880_pmx_func sdhci_grp[] = {
+static struct ralink_pmx_func sdhci_grp[] = {
 	FUNC("sdhci", 0, 41, 8),
 	FUNC("nand2", 2, 41, 8),
 };
-static struct rt2880_pmx_func rgmii1_grp[] = { FUNC("rgmii1", 0, 49, 12) };
+static struct ralink_pmx_func rgmii1_grp[] = { FUNC("rgmii1", 0, 49, 12) };
 
-static struct rt2880_pmx_group mt7621_pinmux_data[] = {
+static struct ralink_pmx_group mt7621_pinmux_data[] = {
 	GRP("uart1", uart1_grp, 1, MT7621_GPIO_MODE_UART1),
 	GRP("i2c", i2c_grp, 1, MT7621_GPIO_MODE_I2C),
 	GRP_G("uart3", uart3_grp, MT7621_GPIO_MODE_UART3_MASK,
@@ -92,7 +92,7 @@
 
 static int mt7621_pinmux_probe(struct platform_device *pdev)
 {
-	return rt2880_pinmux_init(pdev, mt7621_pinmux_data);
+	return ralink_pinmux_init(pdev, mt7621_pinmux_data);
 }
 
 static const struct of_device_id mt7621_pinmux_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-ralink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-ralink.c
@@ -0,0 +1,351 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Copyright (C) 2013 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/machine.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/mt7620.h>
+
+#include "pinctrl-ralink.h"
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+#define SYSC_REG_GPIO_MODE	0x60
+#define SYSC_REG_GPIO_MODE2	0x64
+
+struct ralink_priv {
+	struct device *dev;
+
+	struct pinctrl_pin_desc *pads;
+	struct pinctrl_desc *desc;
+
+	struct ralink_pmx_func **func;
+	int func_count;
+
+	struct ralink_pmx_group *groups;
+	const char **group_names;
+	int group_count;
+
+	u8 *gpio;
+	int max_pins;
+};
+
+static int ralink_get_group_count(struct pinctrl_dev *pctrldev)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	return p->group_count;
+}
+
+static const char *ralink_get_group_name(struct pinctrl_dev *pctrldev,
+					 unsigned int group)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	return (group >= p->group_count) ? NULL : p->group_names[group];
+}
+
+static int ralink_get_group_pins(struct pinctrl_dev *pctrldev,
+				 unsigned int group,
+				 const unsigned int **pins,
+				 unsigned int *num_pins)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	if (group >= p->group_count)
+		return -EINVAL;
+
+	*pins = p->groups[group].func[0].pins;
+	*num_pins = p->groups[group].func[0].pin_count;
+
+	return 0;
+}
+
+static const struct pinctrl_ops ralink_pctrl_ops = {
+	.get_groups_count	= ralink_get_group_count,
+	.get_group_name		= ralink_get_group_name,
+	.get_group_pins		= ralink_get_group_pins,
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_all,
+	.dt_free_map		= pinconf_generic_dt_free_map,
+};
+
+static int ralink_pmx_func_count(struct pinctrl_dev *pctrldev)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	return p->func_count;
+}
+
+static const char *ralink_pmx_func_name(struct pinctrl_dev *pctrldev,
+					unsigned int func)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	return p->func[func]->name;
+}
+
+static int ralink_pmx_group_get_groups(struct pinctrl_dev *pctrldev,
+				       unsigned int func,
+				       const char * const **groups,
+				       unsigned int * const num_groups)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	if (p->func[func]->group_count == 1)
+		*groups = &p->group_names[p->func[func]->groups[0]];
+	else
+		*groups = p->group_names;
+
+	*num_groups = p->func[func]->group_count;
+
+	return 0;
+}
+
+static int ralink_pmx_group_enable(struct pinctrl_dev *pctrldev,
+				   unsigned int func, unsigned int group)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+	u32 mode = 0;
+	u32 reg = SYSC_REG_GPIO_MODE;
+	int i;
+	int shift;
+
+	/* dont allow double use */
+	if (p->groups[group].enabled) {
+		dev_err(p->dev, "%s is already enabled\n",
+			p->groups[group].name);
+		return 0;
+	}
+
+	p->groups[group].enabled = 1;
+	p->func[func]->enabled = 1;
+
+	shift = p->groups[group].shift;
+	if (shift >= 32) {
+		shift -= 32;
+		reg = SYSC_REG_GPIO_MODE2;
+	}
+	mode = rt_sysc_r32(reg);
+	mode &= ~(p->groups[group].mask << shift);
+
+	/* mark the pins as gpio */
+	for (i = 0; i < p->groups[group].func[0].pin_count; i++)
+		p->gpio[p->groups[group].func[0].pins[i]] = 1;
+
+	/* function 0 is gpio and needs special handling */
+	if (func == 0) {
+		mode |= p->groups[group].gpio << shift;
+	} else {
+		for (i = 0; i < p->func[func]->pin_count; i++)
+			p->gpio[p->func[func]->pins[i]] = 0;
+		mode |= p->func[func]->value << shift;
+	}
+	rt_sysc_w32(mode, reg);
+
+	return 0;
+}
+
+static int ralink_pmx_group_gpio_request_enable(struct pinctrl_dev *pctrldev,
+						struct pinctrl_gpio_range *range,
+						unsigned int pin)
+{
+	struct ralink_priv *p = pinctrl_dev_get_drvdata(pctrldev);
+
+	if (!p->gpio[pin]) {
+		dev_err(p->dev, "pin %d is not set to gpio mux\n", pin);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct pinmux_ops ralink_pmx_group_ops = {
+	.get_functions_count	= ralink_pmx_func_count,
+	.get_function_name	= ralink_pmx_func_name,
+	.get_function_groups	= ralink_pmx_group_get_groups,
+	.set_mux		= ralink_pmx_group_enable,
+	.gpio_request_enable	= ralink_pmx_group_gpio_request_enable,
+};
+
+static struct pinctrl_desc ralink_pctrl_desc = {
+	.owner		= THIS_MODULE,
+	.name		= "ralink-pinmux",
+	.pctlops	= &ralink_pctrl_ops,
+	.pmxops		= &ralink_pmx_group_ops,
+};
+
+static struct ralink_pmx_func gpio_func = {
+	.name = "gpio",
+};
+
+static int ralink_pinmux_index(struct ralink_priv *p)
+{
+	struct ralink_pmx_group *mux = p->groups;
+	int i, j, c = 0;
+
+	/* count the mux functions */
+	while (mux->name) {
+		p->group_count++;
+		mux++;
+	}
+
+	/* allocate the group names array needed by the gpio function */
+	p->group_names = devm_kcalloc(p->dev, p->group_count,
+				      sizeof(char *), GFP_KERNEL);
+	if (!p->group_names)
+		return -ENOMEM;
+
+	for (i = 0; i < p->group_count; i++) {
+		p->group_names[i] = p->groups[i].name;
+		p->func_count += p->groups[i].func_count;
+	}
+
+	/* we have a dummy function[0] for gpio */
+	p->func_count++;
+
+	/* allocate our function and group mapping index buffers */
+	p->func = devm_kcalloc(p->dev, p->func_count,
+			       sizeof(*p->func), GFP_KERNEL);
+	gpio_func.groups = devm_kcalloc(p->dev, p->group_count, sizeof(int),
+					GFP_KERNEL);
+	if (!p->func || !gpio_func.groups)
+		return -ENOMEM;
+
+	/* add a backpointer to the function so it knows its group */
+	gpio_func.group_count = p->group_count;
+	for (i = 0; i < gpio_func.group_count; i++)
+		gpio_func.groups[i] = i;
+
+	p->func[c] = &gpio_func;
+	c++;
+
+	/* add remaining functions */
+	for (i = 0; i < p->group_count; i++) {
+		for (j = 0; j < p->groups[i].func_count; j++) {
+			p->func[c] = &p->groups[i].func[j];
+			p->func[c]->groups = devm_kzalloc(p->dev, sizeof(int),
+						    GFP_KERNEL);
+			if (!p->func[c]->groups)
+				return -ENOMEM;
+			p->func[c]->groups[0] = i;
+			p->func[c]->group_count = 1;
+			c++;
+		}
+	}
+	return 0;
+}
+
+static int ralink_pinmux_pins(struct ralink_priv *p)
+{
+	int i, j;
+
+	/*
+	 * loop over the functions and initialize the pins array.
+	 * also work out the highest pin used.
+	 */
+	for (i = 0; i < p->func_count; i++) {
+		int pin;
+
+		if (!p->func[i]->pin_count)
+			continue;
+
+		p->func[i]->pins = devm_kcalloc(p->dev,
+						p->func[i]->pin_count,
+						sizeof(int),
+						GFP_KERNEL);
+		if (!p->func[i]->pins)
+			return -ENOMEM;
+		for (j = 0; j < p->func[i]->pin_count; j++)
+			p->func[i]->pins[j] = p->func[i]->pin_first + j;
+
+		pin = p->func[i]->pin_first + p->func[i]->pin_count;
+		if (pin > p->max_pins)
+			p->max_pins = pin;
+	}
+
+	/* the buffer that tells us which pins are gpio */
+	p->gpio = devm_kcalloc(p->dev, p->max_pins, sizeof(u8), GFP_KERNEL);
+	/* the pads needed to tell pinctrl about our pins */
+	p->pads = devm_kcalloc(p->dev, p->max_pins,
+			       sizeof(struct pinctrl_pin_desc), GFP_KERNEL);
+	if (!p->pads || !p->gpio)
+		return -ENOMEM;
+
+	memset(p->gpio, 1, sizeof(u8) * p->max_pins);
+	for (i = 0; i < p->func_count; i++) {
+		if (!p->func[i]->pin_count)
+			continue;
+
+		for (j = 0; j < p->func[i]->pin_count; j++)
+			p->gpio[p->func[i]->pins[j]] = 0;
+	}
+
+	/* pin 0 is always a gpio */
+	p->gpio[0] = 1;
+
+	/* set the pads */
+	for (i = 0; i < p->max_pins; i++) {
+		/* strlen("ioXY") + 1 = 5 */
+		char *name = devm_kzalloc(p->dev, 5, GFP_KERNEL);
+
+		if (!name)
+			return -ENOMEM;
+		snprintf(name, 5, "io%d", i);
+		p->pads[i].number = i;
+		p->pads[i].name = name;
+	}
+	p->desc->pins = p->pads;
+	p->desc->npins = p->max_pins;
+
+	return 0;
+}
+
+int ralink_pinmux_init(struct platform_device *pdev,
+		       struct ralink_pmx_group *data)
+{
+	struct ralink_priv *p;
+	struct pinctrl_dev *dev;
+	int err;
+
+	if (!data)
+		return -ENOTSUPP;
+
+	/* setup the private data */
+	p = devm_kzalloc(&pdev->dev, sizeof(struct ralink_priv), GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
+	p->dev = &pdev->dev;
+	p->desc = &ralink_pctrl_desc;
+	p->groups = data;
+	platform_set_drvdata(pdev, p);
+
+	/* init the device */
+	err = ralink_pinmux_index(p);
+	if (err) {
+		dev_err(&pdev->dev, "failed to load index\n");
+		return err;
+	}
+
+	err = ralink_pinmux_pins(p);
+	if (err) {
+		dev_err(&pdev->dev, "failed to load pins\n");
+		return err;
+	}
+	dev = pinctrl_register(p->desc, &pdev->dev, p);
+
+	return PTR_ERR_OR_ZERO(dev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-ralink.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-ralink.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Copyright (C) 2012 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _PINCTRL_RALINK_H__
+#define _PINCTRL_RALINK_H__
+
+#define FUNC(name, value, pin_first, pin_count) \
+	{ name, value, pin_first, pin_count }
+
+#define GRP(_name, _func, _mask, _shift) \
+	{ .name = _name, .mask = _mask, .shift = _shift, \
+	  .func = _func, .gpio = _mask, \
+	  .func_count = ARRAY_SIZE(_func) }
+
+#define GRP_G(_name, _func, _mask, _gpio, _shift) \
+	{ .name = _name, .mask = _mask, .shift = _shift, \
+	  .func = _func, .gpio = _gpio, \
+	  .func_count = ARRAY_SIZE(_func) }
+
+struct ralink_pmx_group;
+
+struct ralink_pmx_func {
+	const char *name;
+	const char value;
+
+	int pin_first;
+	int pin_count;
+	int *pins;
+
+	int *groups;
+	int group_count;
+
+	int enabled;
+};
+
+struct ralink_pmx_group {
+	const char *name;
+	int enabled;
+
+	const u32 shift;
+	const char mask;
+	const char gpio;
+
+	struct ralink_pmx_func *func;
+	int func_count;
+};
+
+int ralink_pinmux_init(struct platform_device *pdev,
+		       struct ralink_pmx_group *data);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-rt288x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-rt288x.c
@@ -4,7 +4,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
-#include "pinmux.h"
+#include "pinctrl-ralink.h"
 
 #define RT2880_GPIO_MODE_I2C		BIT(0)
 #define RT2880_GPIO_MODE_UART0		BIT(1)
@@ -15,15 +15,15 @@
 #define RT2880_GPIO_MODE_SDRAM		BIT(6)
 #define RT2880_GPIO_MODE_PCI		BIT(7)
 
-static struct rt2880_pmx_func i2c_func[] = { FUNC("i2c", 0, 1, 2) };
-static struct rt2880_pmx_func spi_func[] = { FUNC("spi", 0, 3, 4) };
-static struct rt2880_pmx_func uartlite_func[] = { FUNC("uartlite", 0, 7, 8) };
-static struct rt2880_pmx_func jtag_func[] = { FUNC("jtag", 0, 17, 5) };
-static struct rt2880_pmx_func mdio_func[] = { FUNC("mdio", 0, 22, 2) };
-static struct rt2880_pmx_func sdram_func[] = { FUNC("sdram", 0, 24, 16) };
-static struct rt2880_pmx_func pci_func[] = { FUNC("pci", 0, 40, 32) };
+static struct ralink_pmx_func i2c_func[] = { FUNC("i2c", 0, 1, 2) };
+static struct ralink_pmx_func spi_func[] = { FUNC("spi", 0, 3, 4) };
+static struct ralink_pmx_func uartlite_func[] = { FUNC("uartlite", 0, 7, 8) };
+static struct ralink_pmx_func jtag_func[] = { FUNC("jtag", 0, 17, 5) };
+static struct ralink_pmx_func mdio_func[] = { FUNC("mdio", 0, 22, 2) };
+static struct ralink_pmx_func sdram_func[] = { FUNC("sdram", 0, 24, 16) };
+static struct ralink_pmx_func pci_func[] = { FUNC("pci", 0, 40, 32) };
 
-static struct rt2880_pmx_group rt2880_pinmux_data_act[] = {
+static struct ralink_pmx_group rt2880_pinmux_data_act[] = {
 	GRP("i2c", i2c_func, 1, RT2880_GPIO_MODE_I2C),
 	GRP("spi", spi_func, 1, RT2880_GPIO_MODE_SPI),
 	GRP("uartlite", uartlite_func, 1, RT2880_GPIO_MODE_UART0),
@@ -36,7 +36,7 @@
 
 static int rt288x_pinmux_probe(struct platform_device *pdev)
 {
-	return rt2880_pinmux_init(pdev, rt2880_pinmux_data_act);
+	return ralink_pinmux_init(pdev, rt2880_pinmux_data_act);
 }
 
 static const struct of_device_id rt288x_pinmux_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-rt305x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-rt305x.c
@@ -5,7 +5,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
-#include "pinmux.h"
+#include "pinctrl-ralink.h"
 
 #define RT305X_GPIO_MODE_UART0_SHIFT	2
 #define RT305X_GPIO_MODE_UART0_MASK	0x7
@@ -31,9 +31,9 @@
 #define RT3352_GPIO_MODE_LNA		18
 #define RT3352_GPIO_MODE_PA		20
 
-static struct rt2880_pmx_func i2c_func[] =  { FUNC("i2c", 0, 1, 2) };
-static struct rt2880_pmx_func spi_func[] = { FUNC("spi", 0, 3, 4) };
-static struct rt2880_pmx_func uartf_func[] = {
+static struct ralink_pmx_func i2c_func[] =  { FUNC("i2c", 0, 1, 2) };
+static struct ralink_pmx_func spi_func[] = { FUNC("spi", 0, 3, 4) };
+static struct ralink_pmx_func uartf_func[] = {
 	FUNC("uartf", RT305X_GPIO_MODE_UARTF, 7, 8),
 	FUNC("pcm uartf", RT305X_GPIO_MODE_PCM_UARTF, 7, 8),
 	FUNC("pcm i2s", RT305X_GPIO_MODE_PCM_I2S, 7, 8),
@@ -42,28 +42,28 @@
 	FUNC("gpio uartf", RT305X_GPIO_MODE_GPIO_UARTF, 7, 4),
 	FUNC("gpio i2s", RT305X_GPIO_MODE_GPIO_I2S, 7, 4),
 };
-static struct rt2880_pmx_func uartlite_func[] = { FUNC("uartlite", 0, 15, 2) };
-static struct rt2880_pmx_func jtag_func[] = { FUNC("jtag", 0, 17, 5) };
-static struct rt2880_pmx_func mdio_func[] = { FUNC("mdio", 0, 22, 2) };
-static struct rt2880_pmx_func rt5350_led_func[] = { FUNC("led", 0, 22, 5) };
-static struct rt2880_pmx_func rt5350_cs1_func[] = {
+static struct ralink_pmx_func uartlite_func[] = { FUNC("uartlite", 0, 15, 2) };
+static struct ralink_pmx_func jtag_func[] = { FUNC("jtag", 0, 17, 5) };
+static struct ralink_pmx_func mdio_func[] = { FUNC("mdio", 0, 22, 2) };
+static struct ralink_pmx_func rt5350_led_func[] = { FUNC("led", 0, 22, 5) };
+static struct ralink_pmx_func rt5350_cs1_func[] = {
 	FUNC("spi_cs1", 0, 27, 1),
 	FUNC("wdg_cs1", 1, 27, 1),
 };
-static struct rt2880_pmx_func sdram_func[] = { FUNC("sdram", 0, 24, 16) };
-static struct rt2880_pmx_func rt3352_rgmii_func[] = {
+static struct ralink_pmx_func sdram_func[] = { FUNC("sdram", 0, 24, 16) };
+static struct ralink_pmx_func rt3352_rgmii_func[] = {
 	FUNC("rgmii", 0, 24, 12)
 };
-static struct rt2880_pmx_func rgmii_func[] = { FUNC("rgmii", 0, 40, 12) };
-static struct rt2880_pmx_func rt3352_lna_func[] = { FUNC("lna", 0, 36, 2) };
-static struct rt2880_pmx_func rt3352_pa_func[] = { FUNC("pa", 0, 38, 2) };
-static struct rt2880_pmx_func rt3352_led_func[] = { FUNC("led", 0, 40, 5) };
-static struct rt2880_pmx_func rt3352_cs1_func[] = {
+static struct ralink_pmx_func rgmii_func[] = { FUNC("rgmii", 0, 40, 12) };
+static struct ralink_pmx_func rt3352_lna_func[] = { FUNC("lna", 0, 36, 2) };
+static struct ralink_pmx_func rt3352_pa_func[] = { FUNC("pa", 0, 38, 2) };
+static struct ralink_pmx_func rt3352_led_func[] = { FUNC("led", 0, 40, 5) };
+static struct ralink_pmx_func rt3352_cs1_func[] = {
 	FUNC("spi_cs1", 0, 45, 1),
 	FUNC("wdg_cs1", 1, 45, 1),
 };
 
-static struct rt2880_pmx_group rt3050_pinmux_data[] = {
+static struct ralink_pmx_group rt3050_pinmux_data[] = {
 	GRP("i2c", i2c_func, 1, RT305X_GPIO_MODE_I2C),
 	GRP("spi", spi_func, 1, RT305X_GPIO_MODE_SPI),
 	GRP("uartf", uartf_func, RT305X_GPIO_MODE_UART0_MASK,
@@ -76,7 +76,7 @@
 	{ 0 }
 };
 
-static struct rt2880_pmx_group rt3352_pinmux_data[] = {
+static struct ralink_pmx_group rt3352_pinmux_data[] = {
 	GRP("i2c", i2c_func, 1, RT305X_GPIO_MODE_I2C),
 	GRP("spi", spi_func, 1, RT305X_GPIO_MODE_SPI),
 	GRP("uartf", uartf_func, RT305X_GPIO_MODE_UART0_MASK,
@@ -92,7 +92,7 @@
 	{ 0 }
 };
 
-static struct rt2880_pmx_group rt5350_pinmux_data[] = {
+static struct ralink_pmx_group rt5350_pinmux_data[] = {
 	GRP("i2c", i2c_func, 1, RT305X_GPIO_MODE_I2C),
 	GRP("spi", spi_func, 1, RT305X_GPIO_MODE_SPI),
 	GRP("uartf", uartf_func, RT305X_GPIO_MODE_UART0_MASK,
@@ -107,11 +107,11 @@
 static int rt305x_pinmux_probe(struct platform_device *pdev)
 {
 	if (soc_is_rt5350())
-		return rt2880_pinmux_init(pdev, rt5350_pinmux_data);
+		return ralink_pinmux_init(pdev, rt5350_pinmux_data);
 	else if (soc_is_rt305x() || soc_is_rt3350())
-		return rt2880_pinmux_init(pdev, rt3050_pinmux_data);
+		return ralink_pinmux_init(pdev, rt3050_pinmux_data);
 	else if (soc_is_rt3352())
-		return rt2880_pinmux_init(pdev, rt3352_pinmux_data);
+		return ralink_pinmux_init(pdev, rt3352_pinmux_data);
 	else
 		return -EINVAL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ralink/pinctrl-rt3883.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ralink/pinctrl-rt3883.c
@@ -3,7 +3,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
-#include "pinmux.h"
+#include "pinctrl-ralink.h"
 
 #define RT3883_GPIO_MODE_UART0_SHIFT	2
 #define RT3883_GPIO_MODE_UART0_MASK	0x7
@@ -39,9 +39,9 @@
 #define RT3883_GPIO_MODE_LNA_G_GPIO	0x3
 #define RT3883_GPIO_MODE_LNA_G		_RT3883_GPIO_MODE_LNA_G(RT3883_GPIO_MODE_LNA_G_MASK)
 
-static struct rt2880_pmx_func i2c_func[] =  { FUNC("i2c", 0, 1, 2) };
-static struct rt2880_pmx_func spi_func[] = { FUNC("spi", 0, 3, 4) };
-static struct rt2880_pmx_func uartf_func[] = {
+static struct ralink_pmx_func i2c_func[] =  { FUNC("i2c", 0, 1, 2) };
+static struct ralink_pmx_func spi_func[] = { FUNC("spi", 0, 3, 4) };
+static struct ralink_pmx_func uartf_func[] = {
 	FUNC("uartf", RT3883_GPIO_MODE_UARTF, 7, 8),
 	FUNC("pcm uartf", RT3883_GPIO_MODE_PCM_UARTF, 7, 8),
 	FUNC("pcm i2s", RT3883_GPIO_MODE_PCM_I2S, 7, 8),
@@ -50,21 +50,21 @@
 	FUNC("gpio uartf", RT3883_GPIO_MODE_GPIO_UARTF, 7, 4),
 	FUNC("gpio i2s", RT3883_GPIO_MODE_GPIO_I2S, 7, 4),
 };
-static struct rt2880_pmx_func uartlite_func[] = { FUNC("uartlite", 0, 15, 2) };
-static struct rt2880_pmx_func jtag_func[] = { FUNC("jtag", 0, 17, 5) };
-static struct rt2880_pmx_func mdio_func[] = { FUNC("mdio", 0, 22, 2) };
-static struct rt2880_pmx_func lna_a_func[] = { FUNC("lna a", 0, 32, 3) };
-static struct rt2880_pmx_func lna_g_func[] = { FUNC("lna g", 0, 35, 3) };
-static struct rt2880_pmx_func pci_func[] = {
+static struct ralink_pmx_func uartlite_func[] = { FUNC("uartlite", 0, 15, 2) };
+static struct ralink_pmx_func jtag_func[] = { FUNC("jtag", 0, 17, 5) };
+static struct ralink_pmx_func mdio_func[] = { FUNC("mdio", 0, 22, 2) };
+static struct ralink_pmx_func lna_a_func[] = { FUNC("lna a", 0, 32, 3) };
+static struct ralink_pmx_func lna_g_func[] = { FUNC("lna g", 0, 35, 3) };
+static struct ralink_pmx_func pci_func[] = {
 	FUNC("pci-dev", 0, 40, 32),
 	FUNC("pci-host2", 1, 40, 32),
 	FUNC("pci-host1", 2, 40, 32),
 	FUNC("pci-fnc", 3, 40, 32)
 };
-static struct rt2880_pmx_func ge1_func[] = { FUNC("ge1", 0, 72, 12) };
-static struct rt2880_pmx_func ge2_func[] = { FUNC("ge2", 0, 84, 12) };
+static struct ralink_pmx_func ge1_func[] = { FUNC("ge1", 0, 72, 12) };
+static struct ralink_pmx_func ge2_func[] = { FUNC("ge2", 0, 84, 12) };
 
-static struct rt2880_pmx_group rt3883_pinmux_data[] = {
+static struct ralink_pmx_group rt3883_pinmux_data[] = {
 	GRP("i2c", i2c_func, 1, RT3883_GPIO_MODE_I2C),
 	GRP("spi", spi_func, 1, RT3883_GPIO_MODE_SPI),
 	GRP("uartf", uartf_func, RT3883_GPIO_MODE_UART0_MASK,
@@ -83,7 +83,7 @@
 
 static int rt3883_pinmux_probe(struct platform_device *pdev)
 {
-	return rt2880_pinmux_init(pdev, rt3883_pinmux_data);
+	return ralink_pinmux_init(pdev, rt3883_pinmux_data);
 }
 
 static const struct of_device_id rt3883_pinmux_match[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/Kconfig
@@ -228,6 +228,7 @@
 	depends on OF
 	depends on ARCH_RZN1 || COMPILE_TEST
 	select GENERIC_PINCONF
+	select PINMUX
 	help
 	  This selects pinctrl driver for Renesas RZ/N1 devices.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/core.c
@@ -71,12 +71,11 @@
 
 	/* Fill them. */
 	for (i = 0; i < num_windows; i++) {
-		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
-		windows->phys = res->start;
-		windows->size = resource_size(res);
-		windows->virt = devm_ioremap_resource(pfc->dev, res);
+		windows->virt = devm_platform_get_and_ioremap_resource(pdev, i, &res);
 		if (IS_ERR(windows->virt))
 			return -ENOMEM;
+		windows->phys = res->start;
+		windows->size = resource_size(res);
 		windows++;
 	}
 	for (i = 0; i < num_irqs; i++)
@@ -739,7 +738,7 @@
 
 #ifdef DEBUG
 #define SH_PFC_MAX_REGS		300
-#define SH_PFC_MAX_ENUMS	3000
+#define SH_PFC_MAX_ENUMS	5000
 
 static unsigned int sh_pfc_errors __initdata = 0;
 static unsigned int sh_pfc_warnings __initdata = 0;
@@ -851,7 +850,8 @@
 	sh_pfc_check_reg(drvname, cfg_reg->reg);
 
 	if (cfg_reg->field_width) {
-		n = cfg_reg->reg_width / cfg_reg->field_width;
+		fw = cfg_reg->field_width;
+		n = (cfg_reg->reg_width / fw) << fw;
 		/* Skip field checks (done at build time) */
 		goto check_enum_ids;
 	}
@@ -868,9 +868,11 @@
 		sh_pfc_err("reg 0x%x: var_field_width declares %u instead of %u bits\n",
 			   cfg_reg->reg, rw, cfg_reg->reg_width);
 
-	if (n != cfg_reg->nr_enum_ids)
+	if (n != cfg_reg->nr_enum_ids) {
 		sh_pfc_err("reg 0x%x: enum_ids[] has %u instead of %u values\n",
 			   cfg_reg->reg, cfg_reg->nr_enum_ids, n);
+		n = cfg_reg->nr_enum_ids;
+	}
 
 check_enum_ids:
 	sh_pfc_check_reg_enums(drvname, cfg_reg->reg, cfg_reg->enum_ids, n);
@@ -890,7 +892,7 @@
 		if (!field->pin && !field->offset && !field->size)
 			continue;
 
-		mask = GENMASK(field->offset + field->size, field->offset);
+		mask = GENMASK(field->offset + field->size - 1, field->offset);
 		if (mask & seen)
 			sh_pfc_err("drive_reg 0x%x: field %u overlap\n",
 				   drive->reg, i);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/pfc-r8a77470.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/pfc-r8a77470.c
@@ -2140,7 +2140,7 @@
 	VI0_CLK_MARK,
 };
 /* - VIN1 ------------------------------------------------------------------- */
-static const union vin_data vin1_data_pins = {
+static const union vin_data12 vin1_data_pins = {
 	.data12 = {
 		RCAR_GP_PIN(3,  1), RCAR_GP_PIN(3, 2),
 		RCAR_GP_PIN(3,  3), RCAR_GP_PIN(3, 4),
@@ -2150,7 +2150,7 @@
 		RCAR_GP_PIN(3, 15), RCAR_GP_PIN(3, 16),
 	},
 };
-static const union vin_data vin1_data_mux = {
+static const union vin_data12 vin1_data_mux = {
 	.data12 = {
 		VI1_DATA0_MARK, VI1_DATA1_MARK,
 		VI1_DATA2_MARK, VI1_DATA3_MARK,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/pfc-r8a779a0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/pfc-r8a779a0.c
@@ -629,7 +629,36 @@
 };
 
 static const u16 pinmux_data[] = {
+/* Using GP_2_[2-15] requires disabling I2C in MOD_SEL2 */
+#define GP_2_2_FN	GP_2_2_FN,	FN_SEL_I2C0_0
+#define GP_2_3_FN	GP_2_3_FN,	FN_SEL_I2C0_0
+#define GP_2_4_FN	GP_2_4_FN,	FN_SEL_I2C1_0
+#define GP_2_5_FN	GP_2_5_FN,	FN_SEL_I2C1_0
+#define GP_2_6_FN	GP_2_6_FN,	FN_SEL_I2C2_0
+#define GP_2_7_FN	GP_2_7_FN,	FN_SEL_I2C2_0
+#define GP_2_8_FN	GP_2_8_FN,	FN_SEL_I2C3_0
+#define GP_2_9_FN	GP_2_9_FN,	FN_SEL_I2C3_0
+#define GP_2_10_FN	GP_2_10_FN,	FN_SEL_I2C4_0
+#define GP_2_11_FN	GP_2_11_FN,	FN_SEL_I2C4_0
+#define GP_2_12_FN	GP_2_12_FN,	FN_SEL_I2C5_0
+#define GP_2_13_FN	GP_2_13_FN,	FN_SEL_I2C5_0
+#define GP_2_14_FN	GP_2_14_FN,	FN_SEL_I2C6_0
+#define GP_2_15_FN	GP_2_15_FN,	FN_SEL_I2C6_0
 	PINMUX_DATA_GP_ALL(),
+#undef GP_2_2_FN
+#undef GP_2_3_FN
+#undef GP_2_4_FN
+#undef GP_2_5_FN
+#undef GP_2_6_FN
+#undef GP_2_7_FN
+#undef GP_2_8_FN
+#undef GP_2_9_FN
+#undef GP_2_10_FN
+#undef GP_2_11_FN
+#undef GP_2_12_FN
+#undef GP_2_13_FN
+#undef GP_2_14_FN
+#undef GP_2_15_FN
 
 	PINMUX_SINGLE(MMC_D7),
 	PINMUX_SINGLE(MMC_D6),
@@ -681,16 +710,8 @@
 	PINMUX_SINGLE(PCIE0_CLKREQ_N),
 
 	PINMUX_SINGLE(AVB0_PHY_INT),
-	PINMUX_SINGLE(AVB0_MAGIC),
-	PINMUX_SINGLE(AVB0_MDC),
-	PINMUX_SINGLE(AVB0_MDIO),
-	PINMUX_SINGLE(AVB0_TXCREFCLK),
 
 	PINMUX_SINGLE(AVB1_PHY_INT),
-	PINMUX_SINGLE(AVB1_MAGIC),
-	PINMUX_SINGLE(AVB1_MDC),
-	PINMUX_SINGLE(AVB1_MDIO),
-	PINMUX_SINGLE(AVB1_TXCREFCLK),
 
 	PINMUX_SINGLE(AVB2_AVTP_PPS),
 	PINMUX_SINGLE(AVB2_AVTP_CAPTURE),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/pinctrl-rza2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/pinctrl-rza2.c
@@ -14,6 +14,7 @@
 #include <linux/gpio/driver.h>
 #include <linux/io.h>
 #include <linux/module.h>
+#include <linux/mutex.h>
 #include <linux/of_device.h>
 #include <linux/pinctrl/pinmux.h>
 
@@ -46,6 +47,7 @@
 	struct pinctrl_dev *pctl;
 	struct pinctrl_gpio_range gpio_range;
 	int npins;
+	struct mutex mutex; /* serialize adding groups and functions */
 };
 
 #define RZA2_PDR(port)		(0x0000 + (port) * 2)	/* Direction 16-bit */
@@ -251,6 +253,8 @@
 		return ret;
 	}
 
+	of_node_put(of_args.np);
+
 	if ((of_args.args[0] != 0) ||
 	    (of_args.args[1] != 0) ||
 	    (of_args.args[2] != priv->npins)) {
@@ -359,10 +363,14 @@
 		psel_val[i] = MUX_FUNC(value);
 	}
 
+	mutex_lock(&priv->mutex);
+
 	/* Register a single pin group listing all the pins we read from DT */
 	gsel = pinctrl_generic_add_group(pctldev, np->name, pins, npins, NULL);
-	if (gsel < 0)
-		return gsel;
+	if (gsel < 0) {
+		ret = gsel;
+		goto unlock;
+	}
 
 	/*
 	 * Register a single group function where the 'data' is an array PSEL
@@ -391,6 +399,8 @@
 	(*map)->data.mux.function = np->name;
 	*num_maps = 1;
 
+	mutex_unlock(&priv->mutex);
+
 	return 0;
 
 remove_function:
@@ -399,6 +409,9 @@
 remove_group:
 	pinctrl_generic_remove_group(pctldev, gsel);
 
+unlock:
+	mutex_unlock(&priv->mutex);
+
 	dev_err(priv->dev, "Unable to parse DT node %s\n", np->name);
 
 	return ret;
@@ -474,6 +487,8 @@
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
+	mutex_init(&priv->mutex);
+
 	platform_set_drvdata(pdev, priv);
 
 	priv->npins = (int)(uintptr_t)of_device_get_match_data(&pdev->dev) *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -852,7 +852,7 @@
 	RZG2L_GPIO_PORT_PACK(2, 0x1e, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x1f, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x20, RZG2L_MPXED_PIN_FUNCS),
-	RZG2L_GPIO_PORT_PACK(3, 0x22, RZG2L_MPXED_PIN_FUNCS),
+	RZG2L_GPIO_PORT_PACK(3, 0x21, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x22, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x23, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(3, 0x24, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
@@ -979,6 +979,8 @@
 		return ret;
 	}
 
+	of_node_put(of_args.np);
+
 	if (of_args.args[0] != 0 || of_args.args[1] != 0 ||
 	    of_args.args[2] != ARRAY_SIZE(rzg2l_gpio_names)) {
 		dev_err(pctrl->dev, "gpio-ranges does not match selected SOC\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/renesas/pinctrl-rzn1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/renesas/pinctrl-rzn1.c
@@ -865,17 +865,15 @@
 	ipctl->mdio_func[0] = -1;
 	ipctl->mdio_func[1] = -1;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	ipctl->lev1_protect_phys = (u32)res->start + 0x400;
-	ipctl->lev1 = devm_ioremap_resource(&pdev->dev, res);
+	ipctl->lev1 = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 	if (IS_ERR(ipctl->lev1))
 		return PTR_ERR(ipctl->lev1);
+	ipctl->lev1_protect_phys = (u32)res->start + 0x400;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	ipctl->lev2_protect_phys = (u32)res->start + 0x400;
-	ipctl->lev2 = devm_ioremap_resource(&pdev->dev, res);
+	ipctl->lev2 = devm_platform_get_and_ioremap_resource(pdev, 1, &res);
 	if (IS_ERR(ipctl->lev2))
 		return PTR_ERR(ipctl->lev2);
+	ipctl->lev2_protect_phys = (u32)res->start + 0x400;
 
 	ipctl->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(ipctl->clk))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/samsung/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/samsung/Kconfig
@@ -4,14 +4,13 @@
 #
 config PINCTRL_SAMSUNG
 	bool
-	depends on OF_GPIO
+	select GPIOLIB
 	select PINMUX
 	select PINCONF
 
 config PINCTRL_EXYNOS
 	bool "Pinctrl common driver part for Samsung Exynos SoCs"
-	depends on OF_GPIO
-	depends on ARCH_EXYNOS || ARCH_S5PV210 || COMPILE_TEST
+	depends on ARCH_EXYNOS || ARCH_S5PV210 || (COMPILE_TEST && OF)
 	select PINCTRL_SAMSUNG
 	select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210)
 	select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS
@@ -26,12 +25,10 @@
 
 config PINCTRL_S3C24XX
 	bool "Samsung S3C24XX SoC pinctrl driver"
-	depends on OF_GPIO
-	depends on ARCH_S3C24XX || COMPILE_TEST
+	depends on ARCH_S3C24XX || (COMPILE_TEST && OF)
 	select PINCTRL_SAMSUNG
 
 config PINCTRL_S3C64XX
 	bool "Samsung S3C64XX SoC pinctrl driver"
-	depends on OF_GPIO
-	depends on ARCH_S3C64XX || COMPILE_TEST
+	depends on ARCH_S3C64XX || (COMPILE_TEST && OF)
 	select PINCTRL_SAMSUNG
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
@@ -504,13 +504,11 @@
 		/* pin-controller instance 0 ALIVE data */
 		.pin_banks	= exynos850_pin_banks0,
 		.nr_banks	= ARRAY_SIZE(exynos850_pin_banks0),
-		.eint_gpio_init = exynos_eint_gpio_init,
 		.eint_wkup_init = exynos_eint_wkup_init,
 	}, {
 		/* pin-controller instance 1 CMGP data */
 		.pin_banks	= exynos850_pin_banks1,
 		.nr_banks	= ARRAY_SIZE(exynos850_pin_banks1),
-		.eint_gpio_init = exynos_eint_gpio_init,
 		.eint_wkup_init = exynos_eint_wkup_init,
 	}, {
 		/* pin-controller instance 2 AUD data */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -1002,6 +1002,16 @@
 	return &(of_data->ctrl[id]);
 }
 
+static void samsung_banks_of_node_put(struct samsung_pinctrl_drv_data *d)
+{
+	struct samsung_pin_bank *bank;
+	unsigned int i;
+
+	bank = d->pin_banks;
+	for (i = 0; i < d->nr_banks; ++i, ++bank)
+		of_node_put(bank->of_node);
+}
+
 /* retrieve the soc specific data */
 static const struct samsung_pin_ctrl *
 samsung_pinctrl_get_soc_data(struct samsung_pinctrl_drv_data *d,
@@ -1116,19 +1126,19 @@
 	if (ctrl->retention_data) {
 		drvdata->retention_ctrl = ctrl->retention_data->init(drvdata,
 							  ctrl->retention_data);
-		if (IS_ERR(drvdata->retention_ctrl))
-			return PTR_ERR(drvdata->retention_ctrl);
+		if (IS_ERR(drvdata->retention_ctrl)) {
+			ret = PTR_ERR(drvdata->retention_ctrl);
+			goto err_put_banks;
+		}
 	}
 
 	ret = samsung_pinctrl_register(pdev, drvdata);
 	if (ret)
-		return ret;
+		goto err_put_banks;
 
 	ret = samsung_gpiolib_register(pdev, drvdata);
-	if (ret) {
-		samsung_pinctrl_unregister(pdev, drvdata);
-		return ret;
-	}
+	if (ret)
+		goto err_unregister;
 
 	if (ctrl->eint_gpio_init)
 		ctrl->eint_gpio_init(drvdata);
@@ -1138,6 +1148,12 @@
 	platform_set_drvdata(pdev, drvdata);
 
 	return 0;
+
+err_unregister:
+	samsung_pinctrl_unregister(pdev, drvdata);
+err_put_banks:
+	samsung_banks_of_node_put(drvdata);
+	return ret;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/stm32/pinctrl-stm32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/stm32/pinctrl-stm32.c
@@ -225,6 +225,13 @@
 	pinctrl_gpio_free(chip->base + offset);
 }
 
+static int stm32_gpio_get_noclk(struct gpio_chip *chip, unsigned int offset)
+{
+	struct stm32_gpio_bank *bank = gpiochip_get_data(chip);
+
+	return !!(readl_relaxed(bank->base + STM32_GPIO_IDR) & BIT(offset));
+}
+
 static int stm32_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
 	struct stm32_gpio_bank *bank = gpiochip_get_data(chip);
@@ -232,7 +239,7 @@
 
 	clk_enable(bank->clk);
 
-	ret = !!(readl_relaxed(bank->base + STM32_GPIO_IDR) & BIT(offset));
+	ret = stm32_gpio_get_noclk(chip, offset);
 
 	clk_disable(bank->clk);
 
@@ -311,8 +318,12 @@
 	struct stm32_gpio_bank *bank = d->domain->host_data;
 	int level;
 
+	/* Do not access the GPIO if this is not LEVEL triggered IRQ. */
+	if (!(bank->irq_type[d->hwirq] & IRQ_TYPE_LEVEL_MASK))
+		return;
+
 	/* If level interrupt type then retrig */
-	level = stm32_gpio_get(&bank->gpio_chip, d->hwirq);
+	level = stm32_gpio_get_noclk(&bank->gpio_chip, d->hwirq);
 	if ((level == 0 && bank->irq_type[d->hwirq] == IRQ_TYPE_LEVEL_LOW) ||
 	    (level == 1 && bank->irq_type[d->hwirq] == IRQ_TYPE_LEVEL_HIGH))
 		irq_chip_retrigger_hierarchy(d);
@@ -354,6 +365,7 @@
 {
 	struct stm32_gpio_bank *bank = irq_data->domain->host_data;
 	struct stm32_pinctrl *pctl = dev_get_drvdata(bank->gpio_chip.parent);
+	unsigned long flags;
 	int ret;
 
 	ret = stm32_gpio_direction_input(&bank->gpio_chip, irq_data->hwirq);
@@ -367,6 +379,10 @@
 		return ret;
 	}
 
+	flags = irqd_get_trigger_type(irq_data);
+	if (flags & IRQ_TYPE_LEVEL_MASK)
+		clk_enable(bank->clk);
+
 	return 0;
 }
 
@@ -374,6 +390,9 @@
 {
 	struct stm32_gpio_bank *bank = irq_data->domain->host_data;
 
+	if (bank->irq_type[irq_data->hwirq] & IRQ_TYPE_LEVEL_MASK)
+		clk_disable(bank->clk);
+
 	gpiochip_unlock_as_irq(&bank->gpio_chip, irq_data->hwirq);
 }
 
@@ -1251,10 +1270,10 @@
 		bank_nr = args.args[1] / STM32_GPIO_PINS_PER_BANK;
 		bank->gpio_chip.base = args.args[1];
 
-		npins = args.args[2];
-		while (!of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3,
-							 ++i, &args))
-			npins += args.args[2];
+		/* get the last defined gpio line (offset + nb of pins) */
+		npins = args.args[0] + args.args[2];
+		while (!of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3, ++i, &args))
+			npins = max(npins, (int)(args.args[0] + args.args[2]));
 	} else {
 		bank_nr = pctl->nbanks;
 		bank->gpio_chip.base = bank_nr * STM32_GPIO_PINS_PER_BANK;
@@ -1280,15 +1299,17 @@
 	bank->bank_ioport_nr = bank_ioport_nr;
 	spin_lock_init(&bank->lock);
 
-	/* create irq hierarchical domain */
-	bank->fwnode = of_node_to_fwnode(np);
+	if (pctl->domain) {
+		/* create irq hierarchical domain */
+		bank->fwnode = of_node_to_fwnode(np);
+
+		bank->domain = irq_domain_create_hierarchy(pctl->domain, 0, STM32_GPIO_IRQ_LINE,
+							   bank->fwnode, &stm32_gpio_domain_ops,
+							   bank);
 
-	bank->domain = irq_domain_create_hierarchy(pctl->domain, 0,
-					STM32_GPIO_IRQ_LINE, bank->fwnode,
-					&stm32_gpio_domain_ops, bank);
-
-	if (!bank->domain)
-		return -ENODEV;
+		if (!bank->domain)
+			return -ENODEV;
+	}
 
 	err = gpiochip_add_data(&bank->gpio_chip, bank);
 	if (err) {
@@ -1313,6 +1334,7 @@
 		return ERR_PTR(-ENXIO);
 
 	domain = irq_find_host(parent);
+	of_node_put(parent);
 	if (!domain)
 		/* domain not registered yet */
 		return ERR_PTR(-EPROBE_DEFER);
@@ -1458,6 +1480,8 @@
 	pctl->domain = stm32_pctrl_get_irq_domain(np);
 	if (IS_ERR(pctl->domain))
 		return PTR_ERR(pctl->domain);
+	if (!pctl->domain)
+		dev_warn(dev, "pinctrl without interrupt support\n");
 
 	/* hwspinlock is optional */
 	hwlock_id = of_hwspin_lock_get_id(pdev->dev.of_node, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
@@ -98,7 +98,7 @@
 static struct platform_driver a100_r_pinctrl_driver = {
 	.probe	= a100_r_pinctrl_probe,
 	.driver	= {
-		.name		= "sun50iw10p1-r-pinctrl",
+		.name		= "sun50i-a100-r-pinctrl",
 		.of_match_table	= a100_r_pinctrl_match,
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c
@@ -107,6 +107,7 @@
 	.npins = ARRAY_SIZE(sun50i_h6_r_pins),
 	.pin_base = PL_BASE,
 	.irq_banks = 2,
+	.io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
 };
 
 static int sun50i_h6_r_pinctrl_probe(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
@@ -363,16 +363,16 @@
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
 		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
-		  SUNXI_FUNCTION(0x3, "i2s3"),	/* DO0 */
+		  SUNXI_FUNCTION(0x3, "i2s3_dout0"),	/* DO0 */
 		  SUNXI_FUNCTION(0x4, "spi1"),		/* MISO */
-		  SUNXI_FUNCTION(0x5, "i2s3"),	/* DI1 */
+		  SUNXI_FUNCTION(0x5, "i2s3_din1"),	/* DI1 */
 		  SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)),	/* PH_EINT8 */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
-		  SUNXI_FUNCTION(0x3, "i2s3"),	/* DI0 */
+		  SUNXI_FUNCTION(0x3, "i2s3_din0"),	/* DI0 */
 		  SUNXI_FUNCTION(0x4, "spi1"),		/* CS1 */
-		  SUNXI_FUNCTION(0x3, "i2s3"),	/* DO1 */
+		  SUNXI_FUNCTION(0x5, "i2s3_dout1"),	/* DO1 */
 		  SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)),	/* PH_EINT9 */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/sunxi/pinctrl-sun8i-a83t.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/sunxi/pinctrl-sun8i-a83t.c
@@ -158,26 +158,26 @@
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
-		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ6 */
 		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
-		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ7 */
 		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
-		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQS */
 		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 17),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
-		  SUNXI_FUNCTION(0x2, "nand")),		/* CE2 */
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE2 */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 18),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
-		  SUNXI_FUNCTION(0x2, "nand")),		/* CE3 */
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE3 */
 	/* Hole */
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/sunxi/pinctrl-suniv-f1c100s.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/sunxi/pinctrl-suniv-f1c100s.c
@@ -204,7 +204,7 @@
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
 		  SUNXI_FUNCTION(0x1, "gpio_out"),
 		  SUNXI_FUNCTION(0x2, "lcd"),		/* D20 */
-		  SUNXI_FUNCTION(0x3, "lvds1"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "uart2"),		/* RX */
 		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),
 	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
 		  SUNXI_FUNCTION(0x0, "gpio_in"),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/sunxi/pinctrl-sunxi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/sunxi/pinctrl-sunxi.c
@@ -36,6 +36,13 @@
 #include "../core.h"
 #include "pinctrl-sunxi.h"
 
+/*
+ * These lock classes tell lockdep that GPIO IRQs are in a different
+ * category than their parents, so it won't report false recursion.
+ */
+static struct lock_class_key sunxi_pinctrl_irq_lock_class;
+static struct lock_class_key sunxi_pinctrl_irq_request_class;
+
 static struct irq_chip sunxi_pinctrl_edge_irq_chip;
 static struct irq_chip sunxi_pinctrl_level_irq_chip;
 
@@ -537,6 +544,8 @@
 	struct sunxi_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
 	int i;
 
+	pin -= pctl->desc->pin_base;
+
 	for (i = 0; i < num_configs; i++) {
 		enum pin_config_param param;
 		unsigned long flags;
@@ -615,7 +624,7 @@
 					 unsigned pin,
 					 struct regulator *supply)
 {
-	unsigned short bank = pin / PINS_PER_BANK;
+	unsigned short bank;
 	unsigned long flags;
 	u32 val, reg;
 	int uV;
@@ -631,6 +640,9 @@
 	if (uV == 0)
 		return 0;
 
+	pin -= pctl->desc->pin_base;
+	bank = pin / PINS_PER_BANK;
+
 	switch (pctl->desc->io_bias_cfg_variant) {
 	case BIAS_VOLTAGE_GRP_CONFIG:
 		/*
@@ -648,8 +660,6 @@
 		else
 			val = 0xD; /* 3.3V */
 
-		pin -= pctl->desc->pin_base;
-
 		reg = readl(pctl->membase + sunxi_grp_config_reg(pin));
 		reg &= ~IO_BIAS_MASK;
 		writel(reg | val, pctl->membase + sunxi_grp_config_reg(pin));
@@ -1551,6 +1561,8 @@
 	for (i = 0; i < (pctl->desc->irq_banks * IRQ_PER_BANK); i++) {
 		int irqno = irq_create_mapping(pctl->domain, i);
 
+		irq_set_lockdep_class(irqno, &sunxi_pinctrl_irq_lock_class,
+				      &sunxi_pinctrl_irq_request_class);
 		irq_set_chip_and_handler(irqno, &sunxi_pinctrl_edge_irq_chip,
 					 handle_edge_irq);
 		irq_set_chip_data(irqno, pctl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/tegra/pinctrl-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/tegra/pinctrl-tegra.c
@@ -270,6 +270,9 @@
 	val = pmx_readl(pmx, g->mux_bank, g->mux_reg);
 	val &= ~(0x3 << g->mux_bit);
 	val |= i << g->mux_bit;
+	/* Set the SFIO/GPIO selection to SFIO when under pinmux control*/
+	if (pmx->soc->sfsel_in_mux)
+		val |= (1 << g->sfsel_bit);
 	pmx_writel(pmx, val, g->mux_bank, g->mux_reg);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pinctrl/ti/pinctrl-ti-iodelay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pinctrl/ti/pinctrl-ti-iodelay.c
@@ -883,7 +883,7 @@
 	iod->desc.name = dev_name(dev);
 	iod->desc.owner = THIS_MODULE;
 
-	ret = pinctrl_register_and_init(&iod->desc, dev, iod, &iod->pctl);
+	ret = devm_pinctrl_register_and_init(dev, &iod->desc, iod, &iod->pctl);
 	if (ret) {
 		dev_err(dev, "Failed to register pinctrl\n");
 		goto exit_out;
@@ -891,7 +891,11 @@
 
 	platform_set_drvdata(pdev, iod);
 
-	return pinctrl_enable(iod->pctl);
+	ret = pinctrl_enable(iod->pctl);
+	if (ret)
+		goto exit_out;
+
+	return 0;
 
 exit_out:
 	of_node_put(np);
@@ -908,12 +912,6 @@
 {
 	struct ti_iodelay_device *iod = platform_get_drvdata(pdev);
 
-	if (!iod)
-		return 0;
-
-	if (iod->pctl)
-		pinctrl_unregister(iod->pctl);
-
 	ti_iodelay_pinconf_deinit_dev(iod);
 
 	/* Expect other allocations to be freed by devm */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/Makefile
@@ -2,6 +2,7 @@
 
 # tell define_trace.h where to find the cros ec trace header
 CFLAGS_cros_ec_trace.o:=		-I$(src)
+CFLAGS_cros_ec_sensorhub_ring.o:=	-I$(src)
 
 obj-$(CONFIG_CHROMEOS_LAPTOP)		+= chromeos_laptop.o
 obj-$(CONFIG_CHROMEOS_PSTORE)		+= chromeos_pstore.o
@@ -20,7 +21,7 @@
 obj-$(CONFIG_CROS_EC_LIGHTBAR)		+= cros_ec_lightbar.o
 obj-$(CONFIG_CROS_EC_VBC)		+= cros_ec_vbc.o
 obj-$(CONFIG_CROS_EC_DEBUGFS)		+= cros_ec_debugfs.o
-cros-ec-sensorhub-objs			:= cros_ec_sensorhub.o cros_ec_sensorhub_ring.o cros_ec_trace.o
+cros-ec-sensorhub-objs			:= cros_ec_sensorhub.o cros_ec_sensorhub_ring.o
 obj-$(CONFIG_CROS_EC_SENSORHUB)		+= cros-ec-sensorhub.o
 obj-$(CONFIG_CROS_EC_SYSFS)		+= cros_ec_sysfs.o
 obj-$(CONFIG_CROS_USBPD_LOGGER)		+= cros_usbpd_logger.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/chromeos_laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/chromeos_laptop.c
@@ -740,6 +740,7 @@
 chromeos_laptop_prepare_i2c_peripherals(struct chromeos_laptop *cros_laptop,
 					const struct chromeos_laptop *src)
 {
+	struct i2c_peripheral *i2c_peripherals;
 	struct i2c_peripheral *i2c_dev;
 	struct i2c_board_info *info;
 	int i;
@@ -748,17 +749,15 @@
 	if (!src->num_i2c_peripherals)
 		return 0;
 
-	cros_laptop->i2c_peripherals = kmemdup(src->i2c_peripherals,
-					       src->num_i2c_peripherals *
-						sizeof(*src->i2c_peripherals),
-					       GFP_KERNEL);
-	if (!cros_laptop->i2c_peripherals)
+	i2c_peripherals = kmemdup(src->i2c_peripherals,
+					      src->num_i2c_peripherals *
+					  sizeof(*src->i2c_peripherals),
+					  GFP_KERNEL);
+	if (!i2c_peripherals)
 		return -ENOMEM;
 
-	cros_laptop->num_i2c_peripherals = src->num_i2c_peripherals;
-
-	for (i = 0; i < cros_laptop->num_i2c_peripherals; i++) {
-		i2c_dev = &cros_laptop->i2c_peripherals[i];
+	for (i = 0; i < src->num_i2c_peripherals; i++) {
+		i2c_dev = &i2c_peripherals[i];
 		info = &i2c_dev->board_info;
 
 		error = chromeos_laptop_setup_irq(i2c_dev);
@@ -775,16 +774,19 @@
 		}
 	}
 
+	cros_laptop->i2c_peripherals = i2c_peripherals;
+	cros_laptop->num_i2c_peripherals = src->num_i2c_peripherals;
+
 	return 0;
 
 err_out:
 	while (--i >= 0) {
-		i2c_dev = &cros_laptop->i2c_peripherals[i];
+		i2c_dev = &i2c_peripherals[i];
 		info = &i2c_dev->board_info;
 		if (!IS_ERR_OR_NULL(info->fwnode))
 			fwnode_remove_software_node(info->fwnode);
 	}
-	kfree(cros_laptop->i2c_peripherals);
+	kfree(i2c_peripherals);
 	return error;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec.c
@@ -135,16 +135,16 @@
 	buf.msg.command = EC_CMD_HOST_SLEEP_EVENT;
 
 	ret = cros_ec_cmd_xfer_status(ec_dev, &buf.msg);
-
-	/* For now, report failure to transition to S0ix with a warning. */
+	/* Report failure to transition to system wide suspend with a warning. */
 	if (ret >= 0 && ec_dev->host_sleep_v1 &&
-	    (sleep_event == HOST_SLEEP_EVENT_S0IX_RESUME)) {
+	    (sleep_event == HOST_SLEEP_EVENT_S0IX_RESUME ||
+	     sleep_event == HOST_SLEEP_EVENT_S3_RESUME)) {
 		ec_dev->last_resume_result =
 			buf.u.resp1.resume_response.sleep_transitions;
 
 		WARN_ONCE(buf.u.resp1.resume_response.sleep_transitions &
 			  EC_HOST_RESUME_SLEEP_TIMEOUT,
-			  "EC detected sleep transition timeout. Total slp_s0 transitions: %d",
+			  "EC detected sleep transition timeout. Total sleep transitions: %d",
 			  buf.u.resp1.resume_response.sleep_transitions &
 			  EC_HOST_RESUME_SLEEP_TRANSITIONS_MASK);
 	}
@@ -189,6 +189,8 @@
 	ec_dev->max_request = sizeof(struct ec_params_hello);
 	ec_dev->max_response = sizeof(struct ec_response_get_protocol_info);
 	ec_dev->max_passthru = 0;
+	ec_dev->ec = NULL;
+	ec_dev->pd = NULL;
 
 	ec_dev->din = devm_kzalloc(dev, ec_dev->din_size, GFP_KERNEL);
 	if (!ec_dev->din)
@@ -245,18 +247,16 @@
 		if (IS_ERR(ec_dev->pd)) {
 			dev_err(ec_dev->dev,
 				"Failed to create CrOS PD platform device\n");
-			platform_device_unregister(ec_dev->ec);
-			return PTR_ERR(ec_dev->pd);
+			err = PTR_ERR(ec_dev->pd);
+			goto exit;
 		}
 	}
 
 	if (IS_ENABLED(CONFIG_OF) && dev->of_node) {
 		err = devm_of_platform_populate(dev);
 		if (err) {
-			platform_device_unregister(ec_dev->pd);
-			platform_device_unregister(ec_dev->ec);
 			dev_err(dev, "Failed to register sub-devices\n");
-			return err;
+			goto exit;
 		}
 	}
 
@@ -278,7 +278,7 @@
 		err = blocking_notifier_chain_register(&ec_dev->event_notifier,
 						      &ec_dev->notifier_ready);
 		if (err)
-			return err;
+			goto exit;
 	}
 
 	dev_info(dev, "Chrome EC device registered\n");
@@ -291,6 +291,10 @@
 		cros_ec_irq_thread(0, ec_dev);
 
 	return 0;
+exit:
+	platform_device_unregister(ec_dev->ec);
+	platform_device_unregister(ec_dev->pd);
+	return err;
 }
 EXPORT_SYMBOL(cros_ec_register);
 
@@ -349,10 +353,16 @@
 
 static void cros_ec_report_events_during_suspend(struct cros_ec_device *ec_dev)
 {
+	bool wake_event;
+
 	while (ec_dev->mkbp_event_supported &&
-	       cros_ec_get_next_event(ec_dev, NULL, NULL) > 0)
+	       cros_ec_get_next_event(ec_dev, &wake_event, NULL) > 0) {
 		blocking_notifier_call_chain(&ec_dev->event_notifier,
 					     1, ec_dev);
+
+		if (wake_event && device_may_wakeup(ec_dev->dev))
+			pm_wakeup_event(ec_dev->dev, 0);
+	}
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_chardev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_chardev.c
@@ -284,7 +284,7 @@
 	    u_cmd.insize > EC_MAX_MSG_BYTES)
 		return -EINVAL;
 
-	s_cmd = kmalloc(sizeof(*s_cmd) + max(u_cmd.outsize, u_cmd.insize),
+	s_cmd = kzalloc(sizeof(*s_cmd) + max(u_cmd.outsize, u_cmd.insize),
 			GFP_KERNEL);
 	if (!s_cmd)
 		return -ENOMEM;
@@ -301,7 +301,7 @@
 	}
 
 	s_cmd->command += ec->cmd_offset;
-	ret = cros_ec_cmd_xfer_status(ec->ec_dev, s_cmd);
+	ret = cros_ec_cmd_xfer(ec->ec_dev, s_cmd);
 	/* Only copy data to userland if data was received. */
 	if (ret < 0)
 		goto exit;
@@ -327,6 +327,9 @@
 	if (copy_from_user(&s_mem, arg, sizeof(s_mem)))
 		return -EFAULT;
 
+	if (s_mem.bytes > sizeof(s_mem.buffer))
+		return -EINVAL;
+
 	num = ec_dev->cmd_readmem(ec_dev, s_mem.offset, s_mem.bytes,
 				  s_mem.buffer);
 	if (num <= 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_debugfs.c
@@ -25,6 +25,9 @@
 
 #define CIRC_ADD(idx, size, value)	(((idx) + (value)) & ((size) - 1))
 
+/* waitqueue for log readers */
+static DECLARE_WAIT_QUEUE_HEAD(cros_ec_debugfs_log_wq);
+
 /**
  * struct cros_ec_debugfs - EC debugging information.
  *
@@ -33,7 +36,6 @@
  * @log_buffer: circular buffer for console log information
  * @read_msg: preallocated EC command and buffer to read console log
  * @log_mutex: mutex to protect circular buffer
- * @log_wq: waitqueue for log readers
  * @log_poll_work: recurring task to poll EC for new console log data
  * @panicinfo_blob: panicinfo debugfs blob
  */
@@ -44,7 +46,6 @@
 	struct circ_buf log_buffer;
 	struct cros_ec_command *read_msg;
 	struct mutex log_mutex;
-	wait_queue_head_t log_wq;
 	struct delayed_work log_poll_work;
 	/* EC panicinfo */
 	struct debugfs_blob_wrapper panicinfo_blob;
@@ -107,7 +108,7 @@
 			buf_space--;
 		}
 
-		wake_up(&debug_info->log_wq);
+		wake_up(&cros_ec_debugfs_log_wq);
 	}
 
 	mutex_unlock(&debug_info->log_mutex);
@@ -141,7 +142,7 @@
 
 		mutex_unlock(&debug_info->log_mutex);
 
-		ret = wait_event_interruptible(debug_info->log_wq,
+		ret = wait_event_interruptible(cros_ec_debugfs_log_wq,
 					CIRC_CNT(cb->head, cb->tail, LOG_SIZE));
 		if (ret < 0)
 			return ret;
@@ -173,7 +174,7 @@
 	struct cros_ec_debugfs *debug_info = file->private_data;
 	__poll_t mask = 0;
 
-	poll_wait(file, &debug_info->log_wq, wait);
+	poll_wait(file, &cros_ec_debugfs_log_wq, wait);
 
 	mutex_lock(&debug_info->log_mutex);
 	if (CIRC_CNT(debug_info->log_buffer.head,
@@ -325,6 +326,7 @@
 	if (!msg)
 		return 0;
 
+	msg->version = 1;
 	msg->command = EC_CMD_GET_CMD_VERSIONS + ec->cmd_offset;
 	msg->outsize = sizeof(*params);
 	msg->insize = sizeof(*response);
@@ -377,7 +379,6 @@
 	debug_info->log_buffer.tail = 0;
 
 	mutex_init(&debug_info->log_mutex);
-	init_waitqueue_head(&debug_info->log_wq);
 
 	debugfs_create_file("console_log", S_IFREG | 0444, debug_info->dir,
 			    debug_info, &cros_ec_console_log_fops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_proto.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_proto.c
@@ -507,13 +507,13 @@
 	ret = cros_ec_get_host_command_version_mask(ec_dev,
 						    EC_CMD_GET_NEXT_EVENT,
 						    &ver_mask);
-	if (ret < 0 || ver_mask == 0)
+	if (ret < 0 || ver_mask == 0) {
 		ec_dev->mkbp_event_supported = 0;
-	else
+	} else {
 		ec_dev->mkbp_event_supported = fls(ver_mask);
 
-	dev_dbg(ec_dev->dev, "MKBP support version %u\n",
-		ec_dev->mkbp_event_supported - 1);
+		dev_dbg(ec_dev->dev, "MKBP support version %u\n", ec_dev->mkbp_event_supported - 1);
+	}
 
 	/* Probe if host sleep v1 is supported for S0ix failure detection. */
 	ret = cros_ec_get_host_command_version_mask(ec_dev,
@@ -560,22 +560,28 @@
 EXPORT_SYMBOL(cros_ec_query_all);
 
 /**
- * cros_ec_cmd_xfer_status() - Send a command to the ChromeOS EC.
+ * cros_ec_cmd_xfer() - Send a command to the ChromeOS EC.
  * @ec_dev: EC device.
  * @msg: Message to write.
  *
- * Call this to send a command to the ChromeOS EC. This should be used instead of calling the EC's
- * cmd_xfer() callback directly. It returns success status only if both the command was transmitted
- * successfully and the EC replied with success status.
+ * Call this to send a command to the ChromeOS EC. This should be used instead
+ * of calling the EC's cmd_xfer() callback directly. This function does not
+ * convert EC command execution error codes to Linux error codes. Most
+ * in-kernel users will want to use cros_ec_cmd_xfer_status() instead since
+ * that function implements the conversion.
  *
  * Return:
- * >=0 - The number of bytes transferred
- * <0 - Linux error code
+ * >0 - EC command was executed successfully. The return value is the number
+ *      of bytes returned by the EC (excluding the header).
+ * =0 - EC communication was successful. EC command execution results are
+ *      reported in msg->result. The result will be EC_RES_SUCCESS if the
+ *      command was executed successfully or report an EC command execution
+ *      error.
+ * <0 - EC communication error. Return value is the Linux error code.
  */
-int cros_ec_cmd_xfer_status(struct cros_ec_device *ec_dev,
-			    struct cros_ec_command *msg)
+int cros_ec_cmd_xfer(struct cros_ec_device *ec_dev, struct cros_ec_command *msg)
 {
-	int ret, mapped;
+	int ret;
 
 	mutex_lock(&ec_dev->lock);
 	if (ec_dev->proto_version == EC_PROTO_VERSION_UNKNOWN) {
@@ -616,6 +622,32 @@
 	ret = send_command(ec_dev, msg);
 	mutex_unlock(&ec_dev->lock);
 
+	return ret;
+}
+EXPORT_SYMBOL(cros_ec_cmd_xfer);
+
+/**
+ * cros_ec_cmd_xfer_status() - Send a command to the ChromeOS EC.
+ * @ec_dev: EC device.
+ * @msg: Message to write.
+ *
+ * Call this to send a command to the ChromeOS EC. This should be used instead of calling the EC's
+ * cmd_xfer() callback directly. It returns success status only if both the command was transmitted
+ * successfully and the EC replied with success status.
+ *
+ * Return:
+ * >=0 - The number of bytes transferred.
+ * <0 - Linux error code
+ */
+int cros_ec_cmd_xfer_status(struct cros_ec_device *ec_dev,
+			    struct cros_ec_command *msg)
+{
+	int ret, mapped;
+
+	ret = cros_ec_cmd_xfer(ec_dev, msg);
+	if (ret < 0)
+		return ret;
+
 	mapped = cros_ec_map_error(msg->result);
 	if (mapped) {
 		dev_dbg(ec_dev->dev, "Command result (err: %d [%d])\n",
@@ -716,6 +748,7 @@
 	u8 event_type;
 	u32 host_event;
 	int ret;
+	u32 ver_mask;
 
 	/*
 	 * Default value for wake_event.
@@ -737,6 +770,39 @@
 		return get_keyboard_state_event(ec_dev);
 
 	ret = get_next_event(ec_dev);
+	/*
+	 * -ENOPROTOOPT is returned when EC returns EC_RES_INVALID_VERSION.
+	 * This can occur when EC based device (e.g. Fingerprint MCU) jumps to
+	 * the RO image which doesn't support newer version of the command. In
+	 * this case we will attempt to update maximum supported version of the
+	 * EC_CMD_GET_NEXT_EVENT.
+	 */
+	if (ret == -ENOPROTOOPT) {
+		dev_dbg(ec_dev->dev,
+			"GET_NEXT_EVENT returned invalid version error.\n");
+		mutex_lock(&ec_dev->lock);
+		ret = cros_ec_get_host_command_version_mask(ec_dev,
+							EC_CMD_GET_NEXT_EVENT,
+							&ver_mask);
+		mutex_unlock(&ec_dev->lock);
+		if (ret < 0 || ver_mask == 0)
+			/*
+			 * Do not change the MKBP supported version if we can't
+			 * obtain supported version correctly. Please note that
+			 * calling EC_CMD_GET_NEXT_EVENT returned
+			 * EC_RES_INVALID_VERSION which means that the command
+			 * is present.
+			 */
+			return -ENOPROTOOPT;
+
+		ec_dev->mkbp_event_supported = fls(ver_mask);
+		dev_dbg(ec_dev->dev, "MKBP support version changed to %u\n",
+			ec_dev->mkbp_event_supported - 1);
+
+		/* Try to get next event with new MKBP support version set. */
+		ret = get_next_event(ec_dev);
+	}
+
 	if (ret <= 0)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_sensorhub_ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_sensorhub_ring.c
@@ -17,7 +17,8 @@
 #include <linux/sort.h>
 #include <linux/slab.h>
 
-#include "cros_ec_trace.h"
+#define CREATE_TRACE_POINTS
+#include "cros_ec_sensorhub_trace.h"
 
 /* Precision of fixed point for the m values from the filter */
 #define M_PRECISION BIT(23)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_sensorhub_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_sensorhub_trace.h
@@ -0,0 +1,123 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Trace events for the ChromeOS Sensorhub kernel module
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM cros_ec
+
+#if !defined(_CROS_EC_SENSORHUB_TRACE_H_) || defined(TRACE_HEADER_MULTI_READ)
+#define _CROS_EC_SENSORHUB_TRACE_H_
+
+#include <linux/types.h>
+#include <linux/platform_data/cros_ec_sensorhub.h>
+
+#include <linux/tracepoint.h>
+
+TRACE_EVENT(cros_ec_sensorhub_timestamp,
+	    TP_PROTO(u32 ec_sample_timestamp, u32 ec_fifo_timestamp, s64 fifo_timestamp,
+		     s64 current_timestamp, s64 current_time),
+	TP_ARGS(ec_sample_timestamp, ec_fifo_timestamp, fifo_timestamp, current_timestamp,
+		current_time),
+	TP_STRUCT__entry(
+		__field(u32, ec_sample_timestamp)
+		__field(u32, ec_fifo_timestamp)
+		__field(s64, fifo_timestamp)
+		__field(s64, current_timestamp)
+		__field(s64, current_time)
+		__field(s64, delta)
+	),
+	TP_fast_assign(
+		__entry->ec_sample_timestamp = ec_sample_timestamp;
+		__entry->ec_fifo_timestamp = ec_fifo_timestamp;
+		__entry->fifo_timestamp = fifo_timestamp;
+		__entry->current_timestamp = current_timestamp;
+		__entry->current_time = current_time;
+		__entry->delta = current_timestamp - current_time;
+	),
+	TP_printk("ec_ts: %9u, ec_fifo_ts: %9u, fifo_ts: %12lld, curr_ts: %12lld, curr_time: %12lld, delta %12lld",
+		  __entry->ec_sample_timestamp,
+		__entry->ec_fifo_timestamp,
+		__entry->fifo_timestamp,
+		__entry->current_timestamp,
+		__entry->current_time,
+		__entry->delta
+	)
+);
+
+TRACE_EVENT(cros_ec_sensorhub_data,
+	    TP_PROTO(u32 ec_sensor_num, u32 ec_fifo_timestamp, s64 fifo_timestamp,
+		     s64 current_timestamp, s64 current_time),
+	TP_ARGS(ec_sensor_num, ec_fifo_timestamp, fifo_timestamp, current_timestamp, current_time),
+	TP_STRUCT__entry(
+		__field(u32, ec_sensor_num)
+		__field(u32, ec_fifo_timestamp)
+		__field(s64, fifo_timestamp)
+		__field(s64, current_timestamp)
+		__field(s64, current_time)
+		__field(s64, delta)
+	),
+	TP_fast_assign(
+		__entry->ec_sensor_num = ec_sensor_num;
+		__entry->ec_fifo_timestamp = ec_fifo_timestamp;
+		__entry->fifo_timestamp = fifo_timestamp;
+		__entry->current_timestamp = current_timestamp;
+		__entry->current_time = current_time;
+		__entry->delta = current_timestamp - current_time;
+	),
+	TP_printk("ec_num: %4u, ec_fifo_ts: %9u, fifo_ts: %12lld, curr_ts: %12lld, curr_time: %12lld, delta %12lld",
+		  __entry->ec_sensor_num,
+		__entry->ec_fifo_timestamp,
+		__entry->fifo_timestamp,
+		__entry->current_timestamp,
+		__entry->current_time,
+		__entry->delta
+	)
+);
+
+TRACE_EVENT(cros_ec_sensorhub_filter,
+	    TP_PROTO(struct cros_ec_sensors_ts_filter_state *state, s64 dx, s64 dy),
+	TP_ARGS(state, dx, dy),
+	TP_STRUCT__entry(
+		__field(s64, dx)
+		__field(s64, dy)
+		__field(s64, median_m)
+		__field(s64, median_error)
+		__field(s64, history_len)
+		__field(s64, x)
+		__field(s64, y)
+	),
+	TP_fast_assign(
+		__entry->dx = dx;
+		__entry->dy = dy;
+		__entry->median_m = state->median_m;
+		__entry->median_error = state->median_error;
+		__entry->history_len = state->history_len;
+		__entry->x = state->x_offset;
+		__entry->y = state->y_offset;
+	),
+	TP_printk("dx: %12lld. dy: %12lld median_m: %12lld median_error: %12lld len: %lld x: %12lld y: %12lld",
+		  __entry->dx,
+		__entry->dy,
+		__entry->median_m,
+		__entry->median_error,
+		__entry->history_len,
+		__entry->x,
+		__entry->y
+	)
+);
+
+
+#endif /* _CROS_EC_SENSORHUB_TRACE_H_ */
+
+/* this part must be outside header guard */
+
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH .
+
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_FILE cros_ec_sensorhub_trace
+
+#include <trace/define_trace.h>
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_trace.h
@@ -15,7 +15,6 @@
 #include <linux/types.h>
 #include <linux/platform_data/cros_ec_commands.h>
 #include <linux/platform_data/cros_ec_proto.h>
-#include <linux/platform_data/cros_ec_sensorhub.h>
 
 #include <linux/tracepoint.h>
 
@@ -71,100 +70,6 @@
 		  __entry->retval)
 );
 
-TRACE_EVENT(cros_ec_sensorhub_timestamp,
-	    TP_PROTO(u32 ec_sample_timestamp, u32 ec_fifo_timestamp, s64 fifo_timestamp,
-		     s64 current_timestamp, s64 current_time),
-	TP_ARGS(ec_sample_timestamp, ec_fifo_timestamp, fifo_timestamp, current_timestamp,
-		current_time),
-	TP_STRUCT__entry(
-		__field(u32, ec_sample_timestamp)
-		__field(u32, ec_fifo_timestamp)
-		__field(s64, fifo_timestamp)
-		__field(s64, current_timestamp)
-		__field(s64, current_time)
-		__field(s64, delta)
-	),
-	TP_fast_assign(
-		__entry->ec_sample_timestamp = ec_sample_timestamp;
-		__entry->ec_fifo_timestamp = ec_fifo_timestamp;
-		__entry->fifo_timestamp = fifo_timestamp;
-		__entry->current_timestamp = current_timestamp;
-		__entry->current_time = current_time;
-		__entry->delta = current_timestamp - current_time;
-	),
-	TP_printk("ec_ts: %9u, ec_fifo_ts: %9u, fifo_ts: %12lld, curr_ts: %12lld, curr_time: %12lld, delta %12lld",
-		  __entry->ec_sample_timestamp,
-		__entry->ec_fifo_timestamp,
-		__entry->fifo_timestamp,
-		__entry->current_timestamp,
-		__entry->current_time,
-		__entry->delta
-	)
-);
-
-TRACE_EVENT(cros_ec_sensorhub_data,
-	    TP_PROTO(u32 ec_sensor_num, u32 ec_fifo_timestamp, s64 fifo_timestamp,
-		     s64 current_timestamp, s64 current_time),
-	TP_ARGS(ec_sensor_num, ec_fifo_timestamp, fifo_timestamp, current_timestamp, current_time),
-	TP_STRUCT__entry(
-		__field(u32, ec_sensor_num)
-		__field(u32, ec_fifo_timestamp)
-		__field(s64, fifo_timestamp)
-		__field(s64, current_timestamp)
-		__field(s64, current_time)
-		__field(s64, delta)
-	),
-	TP_fast_assign(
-		__entry->ec_sensor_num = ec_sensor_num;
-		__entry->ec_fifo_timestamp = ec_fifo_timestamp;
-		__entry->fifo_timestamp = fifo_timestamp;
-		__entry->current_timestamp = current_timestamp;
-		__entry->current_time = current_time;
-		__entry->delta = current_timestamp - current_time;
-	),
-	TP_printk("ec_num: %4u, ec_fifo_ts: %9u, fifo_ts: %12lld, curr_ts: %12lld, curr_time: %12lld, delta %12lld",
-		  __entry->ec_sensor_num,
-		__entry->ec_fifo_timestamp,
-		__entry->fifo_timestamp,
-		__entry->current_timestamp,
-		__entry->current_time,
-		__entry->delta
-	)
-);
-
-TRACE_EVENT(cros_ec_sensorhub_filter,
-	    TP_PROTO(struct cros_ec_sensors_ts_filter_state *state, s64 dx, s64 dy),
-	TP_ARGS(state, dx, dy),
-	TP_STRUCT__entry(
-		__field(s64, dx)
-		__field(s64, dy)
-		__field(s64, median_m)
-		__field(s64, median_error)
-		__field(s64, history_len)
-		__field(s64, x)
-		__field(s64, y)
-	),
-	TP_fast_assign(
-		__entry->dx = dx;
-		__entry->dy = dy;
-		__entry->median_m = state->median_m;
-		__entry->median_error = state->median_error;
-		__entry->history_len = state->history_len;
-		__entry->x = state->x_offset;
-		__entry->y = state->y_offset;
-	),
-	TP_printk("dx: %12lld. dy: %12lld median_m: %12lld median_error: %12lld len: %lld x: %12lld y: %12lld",
-		  __entry->dx,
-		__entry->dy,
-		__entry->median_m,
-		__entry->median_error,
-		__entry->history_len,
-		__entry->x,
-		__entry->y
-	)
-);
-
-
 #endif /* _CROS_EC_TRACE_H_ */
 
 /* this part must be outside header guard */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_ec_typec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_ec_typec.c
@@ -156,12 +156,12 @@
 	return 0;
 
 role_sw_err:
-	usb_role_switch_put(port->role_sw);
-ori_sw_err:
 	typec_switch_put(port->ori_sw);
-mux_err:
+	port->ori_sw = NULL;
+ori_sw_err:
 	typec_mux_put(port->mux);
-
+	port->mux = NULL;
+mux_err:
 	return -ENODEV;
 }
 
@@ -375,6 +375,7 @@
 	return 0;
 
 unregister_ports:
+	fwnode_handle_put(fwnode);
 	cros_unregister_ports(typec);
 	return ret;
 }
@@ -691,7 +692,7 @@
 		for (j = 0; j < sop_disc->svids[i].mode_count; j++) {
 			memset(&desc, 0, sizeof(desc));
 			desc.svid = sop_disc->svids[i].svid;
-			desc.mode = j;
+			desc.mode = j + 1;
 			desc.vdo = sop_disc->svids[i].mode_vdo[j];
 
 			if (is_partner)
@@ -1106,7 +1107,13 @@
 		return -ENOMEM;
 
 	typec->dev = dev;
+
 	typec->ec = dev_get_drvdata(pdev->dev.parent);
+	if (!typec->ec) {
+		dev_err(dev, "couldn't find parent EC device\n");
+		return -ENODEV;
+	}
+
 	platform_set_drvdata(pdev, typec);
 
 	ret = cros_typec_get_cmd_version(typec);
@@ -1116,6 +1123,9 @@
 	}
 
 	ec_dev = dev_get_drvdata(&typec->ec->ec->dev);
+	if (!ec_dev)
+		return -EPROBE_DEFER;
+
 	typec->typec_cmd_supported = !!cros_ec_check_features(ec_dev, EC_FEATURE_TYPEC_CMD);
 	typec->needs_mux_ack = !!cros_ec_check_features(ec_dev,
 							EC_FEATURE_TYPEC_MUX_REQUIRE_AP_ACK);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/chrome/cros_usbpd_notify.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/chrome/cros_usbpd_notify.c
@@ -285,7 +285,11 @@
 		return ret;
 
 #ifdef CONFIG_ACPI
-	platform_driver_register(&cros_usbpd_notify_acpi_driver);
+	ret = platform_driver_register(&cros_usbpd_notify_acpi_driver);
+	if (ret) {
+		platform_driver_unregister(&cros_usbpd_notify_plat_driver);
+		return ret;
+	}
 #endif
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/mellanox/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/mellanox/Kconfig
@@ -48,6 +48,7 @@
 	tristate "Mellanox BlueField Firmware Boot Control driver"
 	depends on ARM64
 	depends on ACPI
+	depends on NET
 	help
 	  The Mellanox BlueField firmware implements functionality to
 	  request swapping the primary and alternate eMMC boot partition,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/mellanox/mlxbf-bootctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/mellanox/mlxbf-bootctl.c
@@ -17,6 +17,7 @@
 
 #define MLXBF_BOOTCTL_SB_SECURE_MASK		0x03
 #define MLXBF_BOOTCTL_SB_TEST_MASK		0x0c
+#define MLXBF_BOOTCTL_SB_DEV_MASK		BIT(4)
 
 #define MLXBF_SB_KEY_NUM			4
 
@@ -37,11 +38,18 @@
 	{ MLXBF_BOOTCTL_NONE, "none" },
 };
 
+enum {
+	MLXBF_BOOTCTL_SB_LIFECYCLE_PRODUCTION = 0,
+	MLXBF_BOOTCTL_SB_LIFECYCLE_GA_SECURE = 1,
+	MLXBF_BOOTCTL_SB_LIFECYCLE_GA_NON_SECURE = 2,
+	MLXBF_BOOTCTL_SB_LIFECYCLE_RMA = 3
+};
+
 static const char * const mlxbf_bootctl_lifecycle_states[] = {
-	[0] = "Production",
-	[1] = "GA Secured",
-	[2] = "GA Non-Secured",
-	[3] = "RMA",
+	[MLXBF_BOOTCTL_SB_LIFECYCLE_PRODUCTION] = "Production",
+	[MLXBF_BOOTCTL_SB_LIFECYCLE_GA_SECURE] = "GA Secured",
+	[MLXBF_BOOTCTL_SB_LIFECYCLE_GA_NON_SECURE] = "GA Non-Secured",
+	[MLXBF_BOOTCTL_SB_LIFECYCLE_RMA] = "RMA",
 };
 
 /* ARM SMC call which is atomic and no need for lock. */
@@ -165,25 +173,30 @@
 static ssize_t lifecycle_state_show(struct device *dev,
 				    struct device_attribute *attr, char *buf)
 {
+	int status_bits;
+	int use_dev_key;
+	int test_state;
 	int lc_state;
 
-	lc_state = mlxbf_bootctl_smc(MLXBF_BOOTCTL_GET_TBB_FUSE_STATUS,
-				     MLXBF_BOOTCTL_FUSE_STATUS_LIFECYCLE);
-	if (lc_state < 0)
-		return lc_state;
-
-	lc_state &=
-		MLXBF_BOOTCTL_SB_TEST_MASK | MLXBF_BOOTCTL_SB_SECURE_MASK;
+	status_bits = mlxbf_bootctl_smc(MLXBF_BOOTCTL_GET_TBB_FUSE_STATUS,
+					MLXBF_BOOTCTL_FUSE_STATUS_LIFECYCLE);
+	if (status_bits < 0)
+		return status_bits;
+
+	use_dev_key = status_bits & MLXBF_BOOTCTL_SB_DEV_MASK;
+	test_state = status_bits & MLXBF_BOOTCTL_SB_TEST_MASK;
+	lc_state = status_bits & MLXBF_BOOTCTL_SB_SECURE_MASK;
 
 	/*
 	 * If the test bits are set, we specify that the current state may be
 	 * due to using the test bits.
 	 */
-	if (lc_state & MLXBF_BOOTCTL_SB_TEST_MASK) {
-		lc_state &= MLXBF_BOOTCTL_SB_SECURE_MASK;
-
+	if (test_state) {
 		return sprintf(buf, "%s(test)\n",
 			       mlxbf_bootctl_lifecycle_states[lc_state]);
+	} else if (use_dev_key &&
+		   (lc_state == MLXBF_BOOTCTL_SB_LIFECYCLE_GA_SECURE)) {
+		return sprintf(buf, "Secured (development)\n");
 	}
 
 	return sprintf(buf, "%s\n", mlxbf_bootctl_lifecycle_states[lc_state]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/mellanox/mlxbf-pmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/mellanox/mlxbf-pmc.c
@@ -191,6 +191,7 @@
 };
 
 static const struct mlxbf_pmc_events mlxbf_pmc_trio_events_1[] = {
+	{ 0x0, "DISABLE" },
 	{ 0xa0, "TPIO_DATA_BEAT" },
 	{ 0xa1, "TDMA_DATA_BEAT" },
 	{ 0xa2, "MAP_DATA_BEAT" },
@@ -214,6 +215,7 @@
 };
 
 static const struct mlxbf_pmc_events mlxbf_pmc_trio_events_2[] = {
+	{ 0x0, "DISABLE" },
 	{ 0xa0, "TPIO_DATA_BEAT" },
 	{ 0xa1, "TDMA_DATA_BEAT" },
 	{ 0xa2, "MAP_DATA_BEAT" },
@@ -246,6 +248,7 @@
 };
 
 static const struct mlxbf_pmc_events mlxbf_pmc_ecc_events[] = {
+	{ 0x0, "DISABLE" },
 	{ 0x100, "ECC_SINGLE_ERROR_CNT" },
 	{ 0x104, "ECC_DOUBLE_ERROR_CNT" },
 	{ 0x114, "SERR_INJ" },
@@ -258,6 +261,7 @@
 };
 
 static const struct mlxbf_pmc_events mlxbf_pmc_mss_events[] = {
+	{ 0x0, "DISABLE" },
 	{ 0xc0, "RXREQ_MSS" },
 	{ 0xc1, "RXDAT_MSS" },
 	{ 0xc2, "TXRSP_MSS" },
@@ -265,6 +269,7 @@
 };
 
 static const struct mlxbf_pmc_events mlxbf_pmc_hnf_events[] = {
+	{ 0x0, "DISABLE" },
 	{ 0x45, "HNF_REQUESTS" },
 	{ 0x46, "HNF_REJECTS" },
 	{ 0x47, "ALL_BUSY" },
@@ -323,6 +328,7 @@
 };
 
 static const struct mlxbf_pmc_events mlxbf_pmc_hnfnet_events[] = {
+	{ 0x0, "DISABLE" },
 	{ 0x12, "CDN_REQ" },
 	{ 0x13, "DDN_REQ" },
 	{ 0x14, "NDN_REQ" },
@@ -358,7 +364,7 @@
 	{ 0x32, "DDN_DIAG_W_INGRESS" },
 	{ 0x33, "DDN_DIAG_C_INGRESS" },
 	{ 0x34, "DDN_DIAG_CORE_SENT" },
-	{ 0x35, "NDN_DIAG_S_OUT_OF_CRED" },
+	{ 0x35, "NDN_DIAG_N_OUT_OF_CRED" },
 	{ 0x36, "NDN_DIAG_S_OUT_OF_CRED" },
 	{ 0x37, "NDN_DIAG_E_OUT_OF_CRED" },
 	{ 0x38, "NDN_DIAG_W_OUT_OF_CRED" },
@@ -892,7 +898,7 @@
 				uint64_t *result)
 {
 	uint32_t perfcfg_offset, perfval_offset;
-	uint64_t perfmon_cfg, perfevt, perfctl;
+	uint64_t perfmon_cfg, perfevt;
 
 	if (cnt_num >= pmc->block[blk_num].counters)
 		return -EINVAL;
@@ -906,25 +912,6 @@
 
 	/* Set counter in "read" mode */
 	perfmon_cfg = FIELD_PREP(MLXBF_PMC_PERFMON_CONFIG_ADDR,
-				 MLXBF_PMC_PERFCTL);
-	perfmon_cfg |= FIELD_PREP(MLXBF_PMC_PERFMON_CONFIG_STROBE, 1);
-	perfmon_cfg |= FIELD_PREP(MLXBF_PMC_PERFMON_CONFIG_WR_R_B, 0);
-
-	if (mlxbf_pmc_write(pmc->block[blk_num].mmio_base + perfcfg_offset,
-			    MLXBF_PMC_WRITE_REG_64, perfmon_cfg))
-		return -EFAULT;
-
-	/* Check if the counter is enabled */
-
-	if (mlxbf_pmc_read(pmc->block[blk_num].mmio_base + perfval_offset,
-			   MLXBF_PMC_READ_REG_64, &perfctl))
-		return -EFAULT;
-
-	if (!FIELD_GET(MLXBF_PMC_PERFCTL_EN0, perfctl))
-		return -EINVAL;
-
-	/* Set counter in "read" mode */
-	perfmon_cfg = FIELD_PREP(MLXBF_PMC_PERFMON_CONFIG_ADDR,
 				 MLXBF_PMC_PERFEVT);
 	perfmon_cfg |= FIELD_PREP(MLXBF_PMC_PERFMON_CONFIG_STROBE, 1);
 	perfmon_cfg |= FIELD_PREP(MLXBF_PMC_PERFMON_CONFIG_WR_R_B, 0);
@@ -1008,7 +995,7 @@
 	} else
 		return -EINVAL;
 
-	return sprintf(buf, "0x%llx\n", value);
+	return sysfs_emit(buf, "0x%llx\n", value);
 }
 
 /* Store function for "counter" sysfs files */
@@ -1078,13 +1065,13 @@
 
 	err = mlxbf_pmc_read_event(blk_num, cnt_num, is_l3, &evt_num);
 	if (err)
-		return sprintf(buf, "No event being monitored\n");
+		return sysfs_emit(buf, "No event being monitored\n");
 
 	evt_name = mlxbf_pmc_get_event_name(pmc->block_name[blk_num], evt_num);
 	if (!evt_name)
 		return -EINVAL;
 
-	return sprintf(buf, "0x%llx: %s\n", evt_num, evt_name);
+	return sysfs_emit(buf, "0x%llx: %s\n", evt_num, evt_name);
 }
 
 /* Store function for "event" sysfs files */
@@ -1139,9 +1126,9 @@
 		return -EINVAL;
 
 	for (i = 0, buf[0] = '\0'; i < size; ++i) {
-		len += sprintf(e_info, "0x%x: %s\n", events[i].evt_num,
-			       events[i].evt_name);
-		if (len > PAGE_SIZE)
+		len += snprintf(e_info, sizeof(e_info), "0x%x: %s\n",
+				events[i].evt_num, events[i].evt_name);
+		if (len >= PAGE_SIZE)
 			break;
 		strcat(buf, e_info);
 		ret = len;
@@ -1168,7 +1155,7 @@
 
 	value = FIELD_GET(MLXBF_PMC_L3C_PERF_CNT_CFG_EN, perfcnt_cfg);
 
-	return sprintf(buf, "%d\n", value);
+	return sysfs_emit(buf, "%d\n", value);
 }
 
 /* Store function for "enable" sysfs files - only for l3cache */
@@ -1215,6 +1202,8 @@
 	attr->dev_attr.show = mlxbf_pmc_event_list_show;
 	attr->nr = blk_num;
 	attr->dev_attr.attr.name = devm_kasprintf(dev, GFP_KERNEL, "event_list");
+	if (!attr->dev_attr.attr.name)
+		return -ENOMEM;
 	pmc->block[blk_num].block_attr[i] = &attr->dev_attr.attr;
 	attr = NULL;
 
@@ -1227,6 +1216,8 @@
 		attr->nr = blk_num;
 		attr->dev_attr.attr.name = devm_kasprintf(dev, GFP_KERNEL,
 							  "enable");
+		if (!attr->dev_attr.attr.name)
+			return -ENOMEM;
 		pmc->block[blk_num].block_attr[++i] = &attr->dev_attr.attr;
 		attr = NULL;
 	}
@@ -1253,6 +1244,8 @@
 		attr->nr = blk_num;
 		attr->dev_attr.attr.name = devm_kasprintf(dev, GFP_KERNEL,
 							  "counter%d", j);
+		if (!attr->dev_attr.attr.name)
+			return -ENOMEM;
 		pmc->block[blk_num].block_attr[++i] = &attr->dev_attr.attr;
 		attr = NULL;
 
@@ -1264,6 +1257,8 @@
 		attr->nr = blk_num;
 		attr->dev_attr.attr.name = devm_kasprintf(dev, GFP_KERNEL,
 							  "event%d", j);
+		if (!attr->dev_attr.attr.name)
+			return -ENOMEM;
 		pmc->block[blk_num].block_attr[++i] = &attr->dev_attr.attr;
 		attr = NULL;
 	}
@@ -1296,6 +1291,8 @@
 		attr->nr = blk_num;
 		attr->dev_attr.attr.name = devm_kasprintf(dev, GFP_KERNEL,
 							  events[j].evt_name);
+		if (!attr->dev_attr.attr.name)
+			return -ENOMEM;
 		pmc->block[blk_num].block_attr[i] = &attr->dev_attr.attr;
 		attr = NULL;
 		i++;
@@ -1324,6 +1321,8 @@
 	pmc->block[blk_num].block_attr_grp.attrs = pmc->block[blk_num].block_attr;
 	pmc->block[blk_num].block_attr_grp.name = devm_kasprintf(
 		dev, GFP_KERNEL, pmc->block_name[blk_num]);
+	if (!pmc->block[blk_num].block_attr_grp.name)
+		return -ENOMEM;
 	pmc->groups[blk_num] = &pmc->block[blk_num].block_attr_grp;
 
 	return 0;
@@ -1348,9 +1347,8 @@
 
 	for (i = 0; i < pmc->total_blocks; ++i) {
 		if (strstr(pmc->block_name[i], "tile")) {
-			ret = sscanf(pmc->block_name[i], "tile%d", &tile_num);
-			if (ret < 0)
-				return ret;
+			if (sscanf(pmc->block_name[i], "tile%d", &tile_num) != 1)
+				return -EINVAL;
 
 			if (tile_num >= pmc->tile_count)
 				continue;
@@ -1374,8 +1372,8 @@
 		pmc->block[i].counters = info[2];
 		pmc->block[i].type = info[3];
 
-		if (IS_ERR(pmc->block[i].mmio_base))
-			return PTR_ERR(pmc->block[i].mmio_base);
+		if (!pmc->block[i].mmio_base)
+			return -ENOMEM;
 
 		ret = mlxbf_pmc_create_groups(dev, i);
 		if (ret)
@@ -1456,6 +1454,8 @@
 
 	pmc->hwmon_dev = devm_hwmon_device_register_with_groups(
 		dev, "bfperf", pmc, pmc->groups);
+	if (IS_ERR(pmc->hwmon_dev))
+		return PTR_ERR(pmc->hwmon_dev);
 	platform_set_drvdata(pdev, pmc);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/mellanox/mlxbf-tmfifo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/mellanox/mlxbf-tmfifo.c
@@ -56,6 +56,7 @@
  * @vq: pointer to the virtio virtqueue
  * @desc: current descriptor of the pending packet
  * @desc_head: head descriptor of the pending packet
+ * @drop_desc: dummy desc for packet dropping
  * @cur_len: processed length of the current descriptor
  * @rem_len: remaining length of the pending packet
  * @pkt_len: total length of the pending packet
@@ -72,6 +73,7 @@
 	struct virtqueue *vq;
 	struct vring_desc *desc;
 	struct vring_desc *desc_head;
+	struct vring_desc drop_desc;
 	int cur_len;
 	int rem_len;
 	u32 pkt_len;
@@ -83,6 +85,14 @@
 	struct mlxbf_tmfifo *fifo;
 };
 
+/* Check whether vring is in drop mode. */
+#define IS_VRING_DROP(_r) ({ \
+	typeof(_r) (r) = (_r); \
+	(r->desc_head == &r->drop_desc ? true : false); })
+
+/* A stub length to drop maximum length packet. */
+#define VRING_DROP_DESC_MAX_LEN		GENMASK(15, 0)
+
 /* Interrupt types. */
 enum {
 	MLXBF_TM_RX_LWM_IRQ,
@@ -195,7 +205,7 @@
 static efi_char16_t mlxbf_tmfifo_efi_name[] = L"RshimMacAddr";
 
 /* Maximum L2 header length. */
-#define MLXBF_TMFIFO_NET_L2_OVERHEAD	36
+#define MLXBF_TMFIFO_NET_L2_OVERHEAD	(ETH_HLEN + VLAN_HLEN)
 
 /* Supported virtio-net features. */
 #define MLXBF_TMFIFO_NET_FEATURES \
@@ -243,6 +253,7 @@
 		vring->align = SMP_CACHE_BYTES;
 		vring->index = i;
 		vring->vdev_id = tm_vdev->vdev.id.device;
+		vring->drop_desc.len = VRING_DROP_DESC_MAX_LEN;
 		dev = &tm_vdev->vdev.dev;
 
 		size = vring_size(vring->num, vring->align);
@@ -348,7 +359,7 @@
 	return len;
 }
 
-static void mlxbf_tmfifo_release_pending_pkt(struct mlxbf_tmfifo_vring *vring)
+static void mlxbf_tmfifo_release_pkt(struct mlxbf_tmfifo_vring *vring)
 {
 	struct vring_desc *desc_head;
 	u32 len = 0;
@@ -577,19 +588,26 @@
 
 	if (vring->cur_len + sizeof(u64) <= len) {
 		/* The whole word. */
-		if (is_rx)
-			memcpy(addr + vring->cur_len, &data, sizeof(u64));
-		else
-			memcpy(&data, addr + vring->cur_len, sizeof(u64));
+		if (is_rx) {
+			if (!IS_VRING_DROP(vring))
+				memcpy(addr + vring->cur_len, &data,
+				       sizeof(u64));
+		} else {
+			memcpy(&data, addr + vring->cur_len,
+			       sizeof(u64));
+		}
 		vring->cur_len += sizeof(u64);
 	} else {
 		/* Leftover bytes. */
-		if (is_rx)
-			memcpy(addr + vring->cur_len, &data,
-			       len - vring->cur_len);
-		else
+		if (is_rx) {
+			if (!IS_VRING_DROP(vring))
+				memcpy(addr + vring->cur_len, &data,
+				       len - vring->cur_len);
+		} else {
+			data = 0;
 			memcpy(&data, addr + vring->cur_len,
 			       len - vring->cur_len);
+		}
 		vring->cur_len = len;
 	}
 
@@ -606,13 +624,14 @@
  * flag is set.
  */
 static void mlxbf_tmfifo_rxtx_header(struct mlxbf_tmfifo_vring *vring,
-				     struct vring_desc *desc,
+				     struct vring_desc **desc,
 				     bool is_rx, bool *vring_change)
 {
 	struct mlxbf_tmfifo *fifo = vring->fifo;
 	struct virtio_net_config *config;
 	struct mlxbf_tmfifo_msg_hdr hdr;
 	int vdev_id, hdr_len;
+	bool drop_rx = false;
 
 	/* Read/Write packet header. */
 	if (is_rx) {
@@ -632,8 +651,8 @@
 			if (ntohs(hdr.len) >
 			    __virtio16_to_cpu(virtio_legacy_is_little_endian(),
 					      config->mtu) +
-			    MLXBF_TMFIFO_NET_L2_OVERHEAD)
-				return;
+					      MLXBF_TMFIFO_NET_L2_OVERHEAD)
+				drop_rx = true;
 		} else {
 			vdev_id = VIRTIO_ID_CONSOLE;
 			hdr_len = 0;
@@ -648,16 +667,25 @@
 
 			if (!tm_dev2)
 				return;
-			vring->desc = desc;
+			vring->desc = *desc;
 			vring = &tm_dev2->vrings[MLXBF_TMFIFO_VRING_RX];
 			*vring_change = true;
 		}
+
+		if (drop_rx && !IS_VRING_DROP(vring)) {
+			if (vring->desc_head)
+				mlxbf_tmfifo_release_pkt(vring);
+			*desc = &vring->drop_desc;
+			vring->desc_head = *desc;
+			vring->desc = *desc;
+		}
+
 		vring->pkt_len = ntohs(hdr.len) + hdr_len;
 	} else {
 		/* Network virtio has an extra header. */
 		hdr_len = (vring->vdev_id == VIRTIO_ID_NET) ?
 			   sizeof(struct virtio_net_hdr) : 0;
-		vring->pkt_len = mlxbf_tmfifo_get_pkt_len(vring, desc);
+		vring->pkt_len = mlxbf_tmfifo_get_pkt_len(vring, *desc);
 		hdr.type = (vring->vdev_id == VIRTIO_ID_NET) ?
 			    VIRTIO_ID_NET : VIRTIO_ID_CONSOLE;
 		hdr.len = htons(vring->pkt_len - hdr_len);
@@ -690,15 +718,23 @@
 	/* Get the descriptor of the next packet. */
 	if (!vring->desc) {
 		desc = mlxbf_tmfifo_get_next_pkt(vring, is_rx);
-		if (!desc)
-			return false;
+		if (!desc) {
+			/* Drop next Rx packet to avoid stuck. */
+			if (is_rx) {
+				desc = &vring->drop_desc;
+				vring->desc_head = desc;
+				vring->desc = desc;
+			} else {
+				return false;
+			}
+		}
 	} else {
 		desc = vring->desc;
 	}
 
 	/* Beginning of a packet. Start to Rx/Tx packet header. */
 	if (vring->pkt_len == 0) {
-		mlxbf_tmfifo_rxtx_header(vring, desc, is_rx, &vring_change);
+		mlxbf_tmfifo_rxtx_header(vring, &desc, is_rx, &vring_change);
 		(*avail)--;
 
 		/* Return if new packet is for another ring. */
@@ -724,17 +760,24 @@
 		vring->rem_len -= len;
 
 		/* Get the next desc on the chain. */
-		if (vring->rem_len > 0 &&
+		if (!IS_VRING_DROP(vring) && vring->rem_len > 0 &&
 		    (virtio16_to_cpu(vdev, desc->flags) & VRING_DESC_F_NEXT)) {
 			idx = virtio16_to_cpu(vdev, desc->next);
 			desc = &vr->desc[idx];
 			goto mlxbf_tmfifo_desc_done;
 		}
 
-		/* Done and release the pending packet. */
-		mlxbf_tmfifo_release_pending_pkt(vring);
+		/* Done and release the packet. */
 		desc = NULL;
 		fifo->vring[is_rx] = NULL;
+		if (!IS_VRING_DROP(vring)) {
+			mlxbf_tmfifo_release_pkt(vring);
+		} else {
+			vring->pkt_len = 0;
+			vring->desc_head = NULL;
+			vring->desc = NULL;
+			return false;
+		}
 
 		/*
 		 * Make sure the load/store are in order before
@@ -868,6 +911,7 @@
 			tm_vdev = fifo->vdev[VIRTIO_ID_CONSOLE];
 			mlxbf_tmfifo_console_output(tm_vdev, vring);
 			spin_unlock_irqrestore(&fifo->spin_lock[0], flags);
+			set_bit(MLXBF_TM_TX_LWM_IRQ, &fifo->pend_events);
 		} else if (test_and_set_bit(MLXBF_TM_TX_LWM_IRQ,
 					    &fifo->pend_events)) {
 			return true;
@@ -913,7 +957,7 @@
 
 		/* Release the pending packet. */
 		if (vring->desc)
-			mlxbf_tmfifo_release_pending_pkt(vring);
+			mlxbf_tmfifo_release_pkt(vring);
 		vq = vring->vq;
 		if (vq) {
 			vring->vq = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/mips/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/mips/Kconfig
@@ -17,7 +17,7 @@
 if MIPS_PLATFORM_DEVICES
 
 config CPU_HWMON
-	tristate "Loongson-3 CPU HWMon Driver"
+	bool "Loongson-3 CPU HWMon Driver"
 	depends on MACH_LOONGSON64
 	select HWMON
 	default y
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/mips/cpu_hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/mips/cpu_hwmon.c
@@ -55,55 +55,6 @@
 static int nr_packages;
 static struct device *cpu_hwmon_dev;
 
-static SENSOR_DEVICE_ATTR(name, 0444, NULL, NULL, 0);
-
-static struct attribute *cpu_hwmon_attributes[] = {
-	&sensor_dev_attr_name.dev_attr.attr,
-	NULL
-};
-
-/* Hwmon device attribute group */
-static struct attribute_group cpu_hwmon_attribute_group = {
-	.attrs = cpu_hwmon_attributes,
-};
-
-static ssize_t get_cpu_temp(struct device *dev,
-			struct device_attribute *attr, char *buf);
-static ssize_t cpu_temp_label(struct device *dev,
-			struct device_attribute *attr, char *buf);
-
-static SENSOR_DEVICE_ATTR(temp1_input, 0444, get_cpu_temp, NULL, 1);
-static SENSOR_DEVICE_ATTR(temp1_label, 0444, cpu_temp_label, NULL, 1);
-static SENSOR_DEVICE_ATTR(temp2_input, 0444, get_cpu_temp, NULL, 2);
-static SENSOR_DEVICE_ATTR(temp2_label, 0444, cpu_temp_label, NULL, 2);
-static SENSOR_DEVICE_ATTR(temp3_input, 0444, get_cpu_temp, NULL, 3);
-static SENSOR_DEVICE_ATTR(temp3_label, 0444, cpu_temp_label, NULL, 3);
-static SENSOR_DEVICE_ATTR(temp4_input, 0444, get_cpu_temp, NULL, 4);
-static SENSOR_DEVICE_ATTR(temp4_label, 0444, cpu_temp_label, NULL, 4);
-
-static const struct attribute *hwmon_cputemp[4][3] = {
-	{
-		&sensor_dev_attr_temp1_input.dev_attr.attr,
-		&sensor_dev_attr_temp1_label.dev_attr.attr,
-		NULL
-	},
-	{
-		&sensor_dev_attr_temp2_input.dev_attr.attr,
-		&sensor_dev_attr_temp2_label.dev_attr.attr,
-		NULL
-	},
-	{
-		&sensor_dev_attr_temp3_input.dev_attr.attr,
-		&sensor_dev_attr_temp3_label.dev_attr.attr,
-		NULL
-	},
-	{
-		&sensor_dev_attr_temp4_input.dev_attr.attr,
-		&sensor_dev_attr_temp4_label.dev_attr.attr,
-		NULL
-	}
-};
-
 static ssize_t cpu_temp_label(struct device *dev,
 			struct device_attribute *attr, char *buf)
 {
@@ -121,24 +72,47 @@
 	return sprintf(buf, "%d\n", value);
 }
 
-static int create_sysfs_cputemp_files(struct kobject *kobj)
-{
-	int i, ret = 0;
-
-	for (i = 0; i < nr_packages; i++)
-		ret = sysfs_create_files(kobj, hwmon_cputemp[i]);
+static SENSOR_DEVICE_ATTR(temp1_input, 0444, get_cpu_temp, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp1_label, 0444, cpu_temp_label, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp2_input, 0444, get_cpu_temp, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp2_label, 0444, cpu_temp_label, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp3_input, 0444, get_cpu_temp, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp3_label, 0444, cpu_temp_label, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp4_input, 0444, get_cpu_temp, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp4_label, 0444, cpu_temp_label, NULL, 4);
 
-	return ret;
-}
+static struct attribute *cpu_hwmon_attributes[] = {
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_label.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_label.dev_attr.attr,
+	&sensor_dev_attr_temp3_input.dev_attr.attr,
+	&sensor_dev_attr_temp3_label.dev_attr.attr,
+	&sensor_dev_attr_temp4_input.dev_attr.attr,
+	&sensor_dev_attr_temp4_label.dev_attr.attr,
+	NULL
+};
 
-static void remove_sysfs_cputemp_files(struct kobject *kobj)
+static umode_t cpu_hwmon_is_visible(struct kobject *kobj,
+				    struct attribute *attr, int i)
 {
-	int i;
+	int id = i / 2;
 
-	for (i = 0; i < nr_packages; i++)
-		sysfs_remove_files(kobj, hwmon_cputemp[i]);
+	if (id < nr_packages)
+		return attr->mode;
+	return 0;
 }
 
+static struct attribute_group cpu_hwmon_group = {
+	.attrs = cpu_hwmon_attributes,
+	.is_visible = cpu_hwmon_is_visible,
+};
+
+static const struct attribute_group *cpu_hwmon_groups[] = {
+	&cpu_hwmon_group,
+	NULL
+};
+
 #define CPU_THERMAL_THRESHOLD 90000
 static struct delayed_work thermal_work;
 
@@ -159,50 +133,34 @@
 
 static int __init loongson_hwmon_init(void)
 {
-	int ret;
-
 	pr_info("Loongson Hwmon Enter...\n");
 
 	if (cpu_has_csr())
 		csr_temp_enable = csr_readl(LOONGSON_CSR_FEATURES) &
 				  LOONGSON_CSRF_TEMP;
 
-	cpu_hwmon_dev = hwmon_device_register_with_info(NULL, "cpu_hwmon", NULL, NULL, NULL);
-	if (IS_ERR(cpu_hwmon_dev)) {
-		ret = PTR_ERR(cpu_hwmon_dev);
-		pr_err("hwmon_device_register fail!\n");
-		goto fail_hwmon_device_register;
-	}
+	if (!csr_temp_enable && !loongson_chiptemp[0])
+		return -ENODEV;
 
 	nr_packages = loongson_sysconf.nr_cpus /
 		loongson_sysconf.cores_per_package;
 
-	ret = create_sysfs_cputemp_files(&cpu_hwmon_dev->kobj);
-	if (ret) {
-		pr_err("fail to create cpu temperature interface!\n");
-		goto fail_create_sysfs_cputemp_files;
+	cpu_hwmon_dev = hwmon_device_register_with_groups(NULL, "cpu_hwmon",
+							  NULL, cpu_hwmon_groups);
+	if (IS_ERR(cpu_hwmon_dev)) {
+		pr_err("hwmon_device_register fail!\n");
+		return PTR_ERR(cpu_hwmon_dev);
 	}
 
 	INIT_DEFERRABLE_WORK(&thermal_work, do_thermal_timer);
 	schedule_delayed_work(&thermal_work, msecs_to_jiffies(20000));
 
-	return ret;
-
-fail_create_sysfs_cputemp_files:
-	sysfs_remove_group(&cpu_hwmon_dev->kobj,
-				&cpu_hwmon_attribute_group);
-	hwmon_device_unregister(cpu_hwmon_dev);
-
-fail_hwmon_device_register:
-	return ret;
+	return 0;
 }
 
 static void __exit loongson_hwmon_exit(void)
 {
 	cancel_delayed_work_sync(&thermal_work);
-	remove_sysfs_cputemp_files(&cpu_hwmon_dev->kobj);
-	sysfs_remove_group(&cpu_hwmon_dev->kobj,
-				&cpu_hwmon_attribute_group);
 	hwmon_device_unregister(cpu_hwmon_dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/olpc/olpc-ec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/olpc/olpc-ec.c
@@ -264,7 +264,7 @@
 	int i, m;
 	unsigned char ec_cmd[EC_MAX_CMD_ARGS];
 	unsigned int ec_cmd_int[EC_MAX_CMD_ARGS];
-	char cmdbuf[64];
+	char cmdbuf[64] = "";
 	int ec_cmd_bytes;
 
 	mutex_lock(&ec_dbgfs_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/aggregator/controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/aggregator/controller.c
@@ -825,7 +825,7 @@
 
 	cplt->dev = dev;
 
-	cplt->wq = create_workqueue(SSAM_CPLT_WQ_NAME);
+	cplt->wq = alloc_workqueue(SSAM_CPLT_WQ_NAME, WQ_UNBOUND | WQ_MEM_RECLAIM, 0);
 	if (!cplt->wq)
 		return -ENOMEM;
 
@@ -1354,7 +1354,8 @@
 	if (ctrl->state == SSAM_CONTROLLER_UNINITIALIZED)
 		return;
 
-	WARN_ON(ctrl->state != SSAM_CONTROLLER_STOPPED);
+	WARN_ON(ctrl->state != SSAM_CONTROLLER_STOPPED &&
+		ctrl->state != SSAM_CONTROLLER_INITIALIZED);
 
 	/*
 	 * Note: New events could still have been received after the previous
@@ -1700,8 +1701,10 @@
 		return status;
 
 	status = ssam_request_sync_init(rqst, spec->flags);
-	if (status)
+	if (status) {
+		ssam_request_sync_free(rqst);
 		return status;
+	}
 
 	ssam_request_sync_set_resp(rqst, rsp);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/aggregator/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/aggregator/core.c
@@ -230,9 +230,12 @@
 			    size_t n)
 {
 	struct ssam_controller *ctrl;
+	int ret;
 
 	ctrl = serdev_device_get_drvdata(dev);
-	return ssam_controller_receive_buf(ctrl, buf, n);
+	ret = ssam_controller_receive_buf(ctrl, buf, n);
+
+	return ret < 0 ? 0 : ret;
 }
 
 static void ssam_write_wakeup(struct serdev_device *dev)
@@ -816,7 +819,7 @@
 err_bus:
 	return status;
 }
-module_init(ssam_core_init);
+subsys_initcall(ssam_core_init);
 
 static void __exit ssam_core_exit(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/aggregator/ssh_packet_layer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/aggregator/ssh_packet_layer.c
@@ -1596,16 +1596,32 @@
 		ssh_ptl_tx_wakeup_packet(ptl);
 }
 
-static bool ssh_ptl_rx_retransmit_check(struct ssh_ptl *ptl, u8 seq)
+static bool ssh_ptl_rx_retransmit_check(struct ssh_ptl *ptl, const struct ssh_frame *frame)
 {
 	int i;
 
 	/*
+	 * Ignore unsequenced packets. On some devices (notably Surface Pro 9),
+	 * unsequenced events will always be sent with SEQ=0x00. Attempting to
+	 * detect retransmission would thus just block all events.
+	 *
+	 * While sequence numbers would also allow detection of retransmitted
+	 * packets in unsequenced communication, they have only ever been used
+	 * to cover edge-cases in sequenced transmission. In particular, the
+	 * only instance of packets being retransmitted (that we are aware of)
+	 * is due to an ACK timeout. As this does not happen in unsequenced
+	 * communication, skip the retransmission check for those packets
+	 * entirely.
+	 */
+	if (frame->type == SSH_FRAME_TYPE_DATA_NSQ)
+		return false;
+
+	/*
 	 * Check if SEQ has been seen recently (i.e. packet was
 	 * re-transmitted and we should ignore it).
 	 */
 	for (i = 0; i < ARRAY_SIZE(ptl->rx.blocked.seqs); i++) {
-		if (likely(ptl->rx.blocked.seqs[i] != seq))
+		if (likely(ptl->rx.blocked.seqs[i] != frame->seq))
 			continue;
 
 		ptl_dbg(ptl, "ptl: ignoring repeated data packet\n");
@@ -1613,7 +1629,7 @@
 	}
 
 	/* Update list of blocked sequence IDs. */
-	ptl->rx.blocked.seqs[ptl->rx.blocked.offset] = seq;
+	ptl->rx.blocked.seqs[ptl->rx.blocked.offset] = frame->seq;
 	ptl->rx.blocked.offset = (ptl->rx.blocked.offset + 1)
 				  % ARRAY_SIZE(ptl->rx.blocked.seqs);
 
@@ -1624,7 +1640,7 @@
 				 const struct ssh_frame *frame,
 				 const struct ssam_span *payload)
 {
-	if (ssh_ptl_rx_retransmit_check(ptl, frame->seq))
+	if (ssh_ptl_rx_retransmit_check(ptl, frame))
 		return;
 
 	ptl->ops.data_received(ptl, payload);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/aggregator/ssh_request_layer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/aggregator/ssh_request_layer.c
@@ -916,6 +916,20 @@
 	if (sshp_parse_command(dev, data, &command, &command_data))
 		return;
 
+	/*
+	 * Check if the message was intended for us. If not, drop it.
+	 *
+	 * Note: We will need to change this to handle debug messages. On newer
+	 * generation devices, these seem to be sent to tid_out=0x03. We as
+	 * host can still receive them as they can be forwarded via an override
+	 * option on SAM, but doing so does not change tid_out=0x00.
+	 */
+	if (command->tid_out != 0x00) {
+		rtl_warn(rtl, "rtl: dropping message not intended for us (tid = %#04x)\n",
+			 command->tid_out);
+		return;
+	}
+
 	if (ssh_rqid_is_event(get_unaligned_le16(&command->rqid)))
 		ssh_rtl_rx_event(rtl, command, &command_data);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/surface3_power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/surface3_power.c
@@ -233,14 +233,21 @@
 	}
 	bix->last_full_charg_capacity = ret;
 
-	/* get serial number */
+	/*
+	 * Get serial number, on some devices (with unofficial replacement
+	 * battery?) reading any of the serial number range addresses gets
+	 * nacked in this case just leave the serial number empty.
+	 */
 	ret = i2c_smbus_read_i2c_block_data(client, MSHW0011_BAT0_REG_SERIAL_NO,
 					    sizeof(buf), buf);
-	if (ret != sizeof(buf)) {
+	if (ret == -EREMOTEIO) {
+		/* no serial number available */
+	} else if (ret != sizeof(buf)) {
 		dev_err(&client->dev, "Error reading serial no: %d\n", ret);
 		return ret;
+	} else {
+		snprintf(bix->serial, ARRAY_SIZE(bix->serial), "%3pE%6pE", buf + 7, buf);
 	}
-	snprintf(bix->serial, ARRAY_SIZE(bix->serial), "%3pE%6pE", buf + 7, buf);
 
 	/* get cycle count */
 	ret = i2c_smbus_read_word_data(client, MSHW0011_BAT0_REG_CYCLE_CNT);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/surface_aggregator_registry.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/surface_aggregator_registry.c
@@ -77,6 +77,42 @@
 	.parent = &ssam_node_root,
 };
 
+/* HID keyboard (TID1). */
+static const struct software_node ssam_node_hid_tid1_keyboard = {
+	.name = "ssam:01:15:01:01:00",
+	.parent = &ssam_node_root,
+};
+
+/* HID pen stash (TID1; pen taken / stashed away evens). */
+static const struct software_node ssam_node_hid_tid1_penstash = {
+	.name = "ssam:01:15:01:02:00",
+	.parent = &ssam_node_root,
+};
+
+/* HID touchpad (TID1). */
+static const struct software_node ssam_node_hid_tid1_touchpad = {
+	.name = "ssam:01:15:01:03:00",
+	.parent = &ssam_node_root,
+};
+
+/* HID device instance 6 (TID1, unknown HID device). */
+static const struct software_node ssam_node_hid_tid1_iid6 = {
+	.name = "ssam:01:15:01:06:00",
+	.parent = &ssam_node_root,
+};
+
+/* HID device instance 7 (TID1, unknown HID device). */
+static const struct software_node ssam_node_hid_tid1_iid7 = {
+	.name = "ssam:01:15:01:07:00",
+	.parent = &ssam_node_root,
+};
+
+/* HID system controls (TID1). */
+static const struct software_node ssam_node_hid_tid1_sysctrl = {
+	.name = "ssam:01:15:01:08:00",
+	.parent = &ssam_node_root,
+};
+
 /* HID keyboard. */
 static const struct software_node ssam_node_hid_main_keyboard = {
 	.name = "ssam:01:15:02:01:00",
@@ -159,6 +195,21 @@
 	NULL,
 };
 
+/* Devices for Surface Laptop Studio. */
+static const struct software_node *ssam_node_group_sls[] = {
+	&ssam_node_root,
+	&ssam_node_bat_ac,
+	&ssam_node_bat_main,
+	&ssam_node_tmp_pprof,
+	&ssam_node_hid_tid1_keyboard,
+	&ssam_node_hid_tid1_penstash,
+	&ssam_node_hid_tid1_touchpad,
+	&ssam_node_hid_tid1_iid6,
+	&ssam_node_hid_tid1_iid7,
+	&ssam_node_hid_tid1_sysctrl,
+	NULL,
+};
+
 /* Devices for Surface Laptop Go. */
 static const struct software_node *ssam_node_group_slg1[] = {
 	&ssam_node_root,
@@ -507,6 +558,15 @@
 	/* Surface Laptop Go 1 */
 	{ "MSHW0118", (unsigned long)ssam_node_group_slg1 },
 
+	/* Surface Laptop Go 2 */
+	{ "MSHW0290", (unsigned long)ssam_node_group_slg1 },
+
+	/* Surface Laptop Go 3 */
+	{ "MSHW0440", (unsigned long)ssam_node_group_slg1 },
+
+	/* Surface Laptop Studio */
+	{ "MSHW0123", (unsigned long)ssam_node_group_sls },
+
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, ssam_platform_hub_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/surface/surface_platform_profile.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/surface/surface_platform_profile.c
@@ -159,8 +159,7 @@
 	set_bit(PLATFORM_PROFILE_BALANCED_PERFORMANCE, tpd->handler.choices);
 	set_bit(PLATFORM_PROFILE_PERFORMANCE, tpd->handler.choices);
 
-	platform_profile_register(&tpd->handler);
-	return 0;
+	return platform_profile_register(&tpd->handler);
 }
 
 static void surface_platform_profile_remove(struct ssam_device *sdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/Kconfig
@@ -91,6 +91,21 @@
 	help
 	 Say Y here if you want to support WMI-based hotkeys on PEAQ 2-in-1s.
 
+config NVIDIA_WMI_EC_BACKLIGHT
+	tristate "EC Backlight Driver for Hybrid Graphics Notebook Systems"
+	depends on ACPI_WMI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  This driver provides a sysfs backlight interface for notebook systems
+	  which are equipped with NVIDIA hybrid graphics and drive LCD backlight
+	  levels through the Embedded Controller (EC).
+
+	  Say Y or M here if you want to control the backlight on a notebook
+	  system with an EC-driven backlight.
+
+	  If you choose to compile this driver as a module the module will be
+	  called nvidia-wmi-ec-backlight.
+
 config XIAOMI_WMI
 	tristate "Xiaomi WMI key driver"
 	depends on ACPI_WMI
@@ -171,6 +186,7 @@
 config AMD_PMC
 	tristate "AMD SoC PMC driver"
 	depends on ACPI && PCI
+	select SERIO
 	help
 	  The driver provides support for AMD Power Management Controller
 	  primarily responsible for S2Idle transactions that are driven from
@@ -256,6 +272,7 @@
 	depends on RFKILL || RFKILL = n
 	depends on HOTPLUG_PCI
 	depends on ACPI_VIDEO || ACPI_VIDEO = n
+	depends on SERIO_I8042 || SERIO_I8042 = n
 	select INPUT_SPARSEKMAP
 	select LEDS_CLASS
 	select NEW_LEDS
@@ -270,7 +287,6 @@
 config ASUS_NB_WMI
 	tristate "Asus Notebook WMI Driver"
 	depends on ASUS_WMI
-	depends on SERIO_I8042 || SERIO_I8042 = n
 	help
 	  This is a driver for newer Asus notebooks. It adds extra features
 	  like wireless radio and bluetooth control, leds, hotkeys, backlight...
@@ -339,6 +355,20 @@
 	  This is a driver for enabling wifi on some Fujitsu-Siemens Amilo
 	  laptops.
 
+config DELL_UART_BACKLIGHT
+	tristate "Dell AIO UART Backlight driver"
+	depends on SERIAL_8250
+	depends on ACPI
+	help
+	  Say Y here if you want to support Dell AIO UART backlight interface.
+	  The Dell AIO machines released after 2017 come with a UART interface
+	  to communicate with the backlight scalar board. This driver creates
+	  a standard backlight interface and talks to the scalar board through
+	  UART to adjust the AIO screen brightness.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called dell_uart_backlight.
+
 config FUJITSU_LAPTOP
 	tristate "Fujitsu Laptop Extras"
 	depends on ACPI
@@ -388,24 +418,7 @@
 	  of the CPU temperature. Say Y or M if the kernel may be used on a
 	  GPD pocket.
 
-config HP_ACCEL
-	tristate "HP laptop accelerometer"
-	depends on INPUT && ACPI
-	depends on SERIO_I8042
-	select SENSORS_LIS3LV02D
-	select NEW_LEDS
-	select LEDS_CLASS
-	help
-	  This driver provides support for the "Mobile Data Protection System 3D"
-	  or "3D DriveGuard" feature of HP laptops. On such systems the driver
-	  should load automatically (via ACPI alias).
-
-	  Support for a led indicating disk protection will be provided as
-	  hp::hddprotect. For more information on the feature, refer to
-	  Documentation/misc-devices/lis3lv02d.rst.
-
-	  To compile this driver as a module, choose M here: the module will
-	  be called hp_accel.
+source "drivers/platform/x86/hp/Kconfig"
 
 config WIRELESS_HOTKEY
 	tristate "Wireless hotkey button"
@@ -419,29 +432,6 @@
 	 To compile this driver as a module, choose M here: the module will
 	 be called wireless-hotkey.
 
-config HP_WMI
-	tristate "HP WMI extras"
-	depends on ACPI_WMI
-	depends on INPUT
-	depends on RFKILL || RFKILL = n
-	select INPUT_SPARSEKMAP
-	select ACPI_PLATFORM_PROFILE
-	help
-	 Say Y here if you want to support WMI-based hotkeys on HP laptops and
-	 to read data from WMI such as docking or ambient light sensor state.
-
-	 To compile this driver as a module, choose M here: the module will
-	 be called hp-wmi.
-
-config TC1100_WMI
-	tristate "HP Compaq TC1100 Tablet WMI Extras"
-	depends on !X86_64
-	depends on ACPI
-	depends on ACPI_WMI
-	help
-	  This is a driver for the WMI extensions (wireless and bluetooth power
-	  control) of the HP Compaq TC1100 tablet.
-
 config IBM_RTL
 	tristate "Device driver to enable PRTL support"
 	depends on PCI
@@ -871,6 +861,8 @@
 	tristate "Panasonic Laptop Extras"
 	depends on INPUT && ACPI
 	depends on BACKLIGHT_CLASS_DEVICE
+	depends on ACPI_VIDEO=n || ACPI_VIDEO
+	depends on SERIO_I8042 || SERIO_I8042 = n
 	select INPUT_SPARSEKMAP
 	help
 	  This driver adds support for access to backlight control and hotkeys
@@ -927,20 +919,21 @@
 
 	  If you have a Topstar laptop, say Y or M here.
 
-config I2C_MULTI_INSTANTIATE
-	tristate "I2C multi instantiate pseudo device driver"
-	depends on I2C && ACPI
+config SERIAL_MULTI_INSTANTIATE
+	tristate "Serial bus multi instantiate pseudo device driver"
+	depends on I2C && SPI && ACPI
 	help
-	  Some ACPI-based systems list multiple i2c-devices in a single ACPI
-	  firmware-node. This driver will instantiate separate i2c-clients
+	  Some ACPI-based systems list multiple devices in a single ACPI
+	  firmware-node. This driver will instantiate separate clients
 	  for each device in the firmware-node.
 
 	  To compile this driver as a module, choose M here: the module
-	  will be called i2c-multi-instantiate.
+	  will be called serial-multi-instantiate.
 
 config MLX_PLATFORM
 	tristate "Mellanox Technologies platform support"
-	depends on I2C && REGMAP
+	depends on I2C
+	select REGMAP
 	help
 	  This option enables system support for the Mellanox Technologies
 	  platform. The Mellanox systems provide data center networking
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/Makefile
@@ -11,6 +11,7 @@
 # WMI drivers
 obj-$(CONFIG_HUAWEI_WMI)		+= huawei-wmi.o
 obj-$(CONFIG_MXM_WMI)			+= mxm-wmi.o
+obj-$(CONFIG_NVIDIA_WMI_EC_BACKLIGHT)	+= nvidia-wmi-ec-backlight.o
 obj-$(CONFIG_PEAQ_WMI)			+= peaq-wmi.o
 obj-$(CONFIG_XIAOMI_WMI)		+= xiaomi-wmi.o
 obj-$(CONFIG_GIGABYTE_WMI)		+= gigabyte-wmi.o
@@ -52,9 +53,7 @@
 obj-$(CONFIG_GPD_POCKET_FAN)	+= gpd-pocket-fan.o
 
 # Hewlett Packard
-obj-$(CONFIG_HP_ACCEL)		+= hp_accel.o
-obj-$(CONFIG_HP_WMI)		+= hp-wmi.o
-obj-$(CONFIG_TC1100_WMI)	+= tc1100-wmi.o
+obj-$(CONFIG_X86_PLATFORM_DRIVERS_HP)	+= hp/
 
 # Hewlett Packard Enterprise
 obj-$(CONFIG_UV_SYSFS)       += uv_sysfs.o
@@ -67,7 +66,7 @@
 obj-$(CONFIG_THINKPAD_LMI)	+= think-lmi.o
 
 # Intel
-obj-$(CONFIG_X86_PLATFORM_DRIVERS_INTEL)		+= intel/
+obj-y				+= intel/
 
 # MSI
 obj-$(CONFIG_MSI_LAPTOP)	+= msi-laptop.o
@@ -104,7 +103,7 @@
 
 # Platform drivers
 obj-$(CONFIG_FW_ATTR_CLASS)		+= firmware_attributes_class.o
-obj-$(CONFIG_I2C_MULTI_INSTANTIATE)	+= i2c-multi-instantiate.o
+obj-$(CONFIG_SERIAL_MULTI_INSTANTIATE)	+= serial-multi-instantiate.o
 obj-$(CONFIG_MLX_PLATFORM)		+= mlx-platform.o
 obj-$(CONFIG_TOUCHSCREEN_DMI)		+= touchscreen_dmi.o
 obj-$(CONFIG_WIRELESS_HOTKEY)		+= wireless-hotkey.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/acer-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/acer-wmi.c
@@ -88,6 +88,7 @@
 	WMID_HOTKEY_EVENT = 0x1,
 	WMID_ACCEL_OR_KBD_DOCK_EVENT = 0x5,
 	WMID_GAMING_TURBO_KEY_EVENT = 0x7,
+	WMID_AC_EVENT = 0x8,
 };
 
 static const struct key_entry acer_wmi_keymap[] __initconst = {
@@ -99,6 +100,7 @@
 	{KE_KEY, 0x22, {KEY_PROG2} },    /* Arcade */
 	{KE_KEY, 0x23, {KEY_PROG3} },    /* P_Key */
 	{KE_KEY, 0x24, {KEY_PROG4} },    /* Social networking_Key */
+	{KE_KEY, 0x27, {KEY_HELP} },
 	{KE_KEY, 0x29, {KEY_PROG3} },    /* P_Key for TM8372 */
 	{KE_IGNORE, 0x41, {KEY_MUTE} },
 	{KE_IGNORE, 0x42, {KEY_PREVIOUSSONG} },
@@ -112,7 +114,13 @@
 	{KE_IGNORE, 0x48, {KEY_VOLUMEUP} },
 	{KE_IGNORE, 0x49, {KEY_VOLUMEDOWN} },
 	{KE_IGNORE, 0x4a, {KEY_VOLUMEDOWN} },
-	{KE_IGNORE, 0x61, {KEY_SWITCHVIDEOMODE} },
+	/*
+	 * 0x61 is KEY_SWITCHVIDEOMODE. Usually this is a duplicate input event
+	 * with the "Video Bus" input device events. But sometimes it is not
+	 * a dup. Map it to KEY_UNKNOWN instead of using KE_IGNORE so that
+	 * udev/hwdb can override it on systems where it is not a dup.
+	 */
+	{KE_KEY, 0x61, {KEY_UNKNOWN} },
 	{KE_IGNORE, 0x62, {KEY_BRIGHTNESSUP} },
 	{KE_IGNORE, 0x63, {KEY_BRIGHTNESSDOWN} },
 	{KE_KEY, 0x64, {KEY_SWITCHVIDEOMODE} },	/* Display Switch */
@@ -559,6 +567,15 @@
 	},
 	{
 		.callback = set_force_caps,
+		.ident = "Acer Aspire Switch V 10 SW5-017",
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "SW5-017"),
+		},
+		.driver_data = (void *)ACER_CAP_KBD_DOCK,
+	},
+	{
+		.callback = set_force_caps,
 		.ident = "Acer One 10 (S1003)",
 		.matches = {
 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"),
@@ -2051,6 +2068,9 @@
 		if (return_value.key_num == 0x4)
 			acer_toggle_turbo();
 		break;
+	case WMID_AC_EVENT:
+		/* We ignore AC events here */
+		break;
 	default:
 		pr_warn("Unknown function number - %d - %d\n",
 			return_value.function, return_value.key_num);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/amd-pmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/amd-pmc.c
@@ -17,9 +17,12 @@
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
+#include <linux/limits.h>
 #include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>
+#include <linux/rtc.h>
+#include <linux/serio.h>
 #include <linux/suspend.h>
 #include <linux/seq_file.h>
 #include <linux/uaccess.h>
@@ -29,6 +32,10 @@
 #define AMD_PMC_REGISTER_RESPONSE	0x980
 #define AMD_PMC_REGISTER_ARGUMENT	0x9BC
 
+/* PMC Scratch Registers */
+#define AMD_PMC_SCRATCH_REG_CZN		0x94
+#define AMD_PMC_SCRATCH_REG_YC		0xD14
+
 /* Base address of SMU for mapping physical address to virtual address */
 #define AMD_PMC_SMU_INDEX_ADDRESS	0xB8
 #define AMD_PMC_SMU_INDEX_DATA		0xBC
@@ -70,7 +77,7 @@
 #define AMD_CPU_ID_CZN			AMD_CPU_ID_RN
 #define AMD_CPU_ID_YC			0x14B5
 
-#define PMC_MSG_DELAY_MIN_US		100
+#define PMC_MSG_DELAY_MIN_US		50
 #define RESPONSE_REGISTER_LOOP_MAX	20000
 
 #define SOC_SUBSYSTEM_IP_MAX	12
@@ -110,6 +117,11 @@
 	u32 base_addr;
 	u32 cpu_id;
 	u32 active_ips;
+/* SMU version information */
+	u8 smu_program;
+	u8 major;
+	u8 minor;
+	u8 rev;
 	struct device *dev;
 	struct mutex lock; /* generic mutex lock */
 #if IS_ENABLED(CONFIG_DEBUG_FS)
@@ -118,7 +130,7 @@
 };
 
 static struct amd_pmc_dev pmc;
-static int amd_pmc_send_cmd(struct amd_pmc_dev *dev, bool set, u32 *data, u8 msg, bool ret);
+static int amd_pmc_send_cmd(struct amd_pmc_dev *dev, u32 arg, u32 *data, u8 msg, bool ret);
 
 static inline u32 amd_pmc_reg_read(struct amd_pmc_dev *dev, int reg_offset)
 {
@@ -147,6 +159,51 @@
 	u64 timecondition_notmet_totaltime[SOC_SUBSYSTEM_IP_MAX];
 } __packed;
 
+static int amd_pmc_get_smu_version(struct amd_pmc_dev *dev)
+{
+	int rc;
+	u32 val;
+
+	rc = amd_pmc_send_cmd(dev, 0, &val, SMU_MSG_GETSMUVERSION, 1);
+	if (rc)
+		return rc;
+
+	dev->smu_program = (val >> 24) & GENMASK(7, 0);
+	dev->major = (val >> 16) & GENMASK(7, 0);
+	dev->minor = (val >> 8) & GENMASK(7, 0);
+	dev->rev = (val >> 0) & GENMASK(7, 0);
+
+	dev_dbg(dev->dev, "SMU program %u version is %u.%u.%u\n",
+		dev->smu_program, dev->major, dev->minor, dev->rev);
+
+	return 0;
+}
+
+static int amd_pmc_idlemask_read(struct amd_pmc_dev *pdev, struct device *dev,
+				 struct seq_file *s)
+{
+	u32 val;
+
+	switch (pdev->cpu_id) {
+	case AMD_CPU_ID_CZN:
+		val = amd_pmc_reg_read(pdev, AMD_PMC_SCRATCH_REG_CZN);
+		break;
+	case AMD_CPU_ID_YC:
+		val = amd_pmc_reg_read(pdev, AMD_PMC_SCRATCH_REG_YC);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (dev)
+		dev_dbg(pdev->dev, "SMU idlemask s0i3: 0x%x\n", val);
+
+	if (s)
+		seq_printf(s, "SMU idlemask : 0x%x\n", val);
+
+	return 0;
+}
+
 #ifdef CONFIG_DEBUG_FS
 static int smu_fw_info_show(struct seq_file *s, void *unused)
 {
@@ -201,6 +258,23 @@
 }
 DEFINE_SHOW_ATTRIBUTE(s0ix_stats);
 
+static int amd_pmc_idlemask_show(struct seq_file *s, void *unused)
+{
+	struct amd_pmc_dev *dev = s->private;
+	int rc;
+
+	if (dev->major > 56 || (dev->major >= 55 && dev->minor >= 37)) {
+		rc = amd_pmc_idlemask_read(dev, NULL, s);
+		if (rc)
+			return rc;
+	} else {
+		seq_puts(s, "Unsupported SMU version for Idlemask\n");
+	}
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(amd_pmc_idlemask);
+
 static void amd_pmc_dbgfs_unregister(struct amd_pmc_dev *dev)
 {
 	debugfs_remove_recursive(dev->dbgfs_dir);
@@ -213,6 +287,8 @@
 			    &smu_fw_info_fops);
 	debugfs_create_file("s0ix_stats", 0644, dev->dbgfs_dir, dev,
 			    &s0ix_stats_fops);
+	debugfs_create_file("amd_pmc_idlemask", 0644, dev->dbgfs_dir, dev,
+			    &amd_pmc_idlemask_fops);
 }
 #else
 static inline void amd_pmc_dbgfs_register(struct amd_pmc_dev *dev)
@@ -264,7 +340,7 @@
 	dev_dbg(dev->dev, "AMD_PMC_REGISTER_MESSAGE:%x\n", value);
 }
 
-static int amd_pmc_send_cmd(struct amd_pmc_dev *dev, bool set, u32 *data, u8 msg, bool ret)
+static int amd_pmc_send_cmd(struct amd_pmc_dev *dev, u32 arg, u32 *data, u8 msg, bool ret)
 {
 	int rc;
 	u32 val;
@@ -283,7 +359,7 @@
 	amd_pmc_reg_write(dev, AMD_PMC_REGISTER_RESPONSE, 0);
 
 	/* Write argument into response register */
-	amd_pmc_reg_write(dev, AMD_PMC_REGISTER_ARGUMENT, set);
+	amd_pmc_reg_write(dev, AMD_PMC_REGISTER_ARGUMENT, arg);
 
 	/* Write message ID to message ID register */
 	amd_pmc_reg_write(dev, AMD_PMC_REGISTER_MESSAGE, msg);
@@ -339,18 +415,112 @@
 	return -EINVAL;
 }
 
+static int amd_pmc_verify_czn_rtc(struct amd_pmc_dev *pdev, u32 *arg)
+{
+	struct rtc_device *rtc_device;
+	time64_t then, now, duration;
+	struct rtc_wkalrm alarm;
+	struct rtc_time tm;
+	int rc;
+
+	if (pdev->major < 64 || (pdev->major == 64 && pdev->minor < 53))
+		return 0;
+
+	rtc_device = rtc_class_open(CONFIG_RTC_SYSTOHC_DEVICE);
+	if (!rtc_device)
+		return 0;
+	rc = rtc_read_alarm(rtc_device, &alarm);
+	if (rc)
+		return rc;
+	if (!alarm.enabled) {
+		dev_dbg(pdev->dev, "alarm not enabled\n");
+		return 0;
+	}
+	rc = rtc_valid_tm(&alarm.time);
+	if (rc)
+		return rc;
+	rc = rtc_read_time(rtc_device, &tm);
+	if (rc)
+		return rc;
+	then = rtc_tm_to_time64(&alarm.time);
+	now = rtc_tm_to_time64(&tm);
+	duration = then-now;
+
+	/* in the past */
+	if (then < now)
+		return 0;
+
+	/* will be stored in upper 16 bits of s0i3 hint argument,
+	 * so timer wakeup from s0i3 is limited to ~18 hours or less
+	 */
+	if (duration <= 4 || duration > U16_MAX)
+		return -EINVAL;
+
+	*arg |= (duration << 16);
+	rc = rtc_alarm_irq_enable(rtc_device, 0);
+	dev_info(pdev->dev, "wakeup timer programmed for %lld seconds\n", duration);
+
+	return rc;
+}
+
+static int amd_pmc_czn_wa_irq1(struct amd_pmc_dev *pdev)
+{
+	struct device *d;
+	int rc;
+
+	if (!pdev->major) {
+		rc = amd_pmc_get_smu_version(pdev);
+		if (rc)
+			return rc;
+	}
+
+	if (pdev->major > 64 || (pdev->major == 64 && pdev->minor > 65))
+		return 0;
+
+	d = bus_find_device_by_name(&serio_bus, NULL, "serio0");
+	if (!d)
+		return 0;
+	if (device_may_wakeup(d)) {
+		dev_info_once(d, "Disabling IRQ1 wakeup source to avoid platform firmware bug\n");
+		disable_irq_wake(1);
+		device_set_wakeup_enable(d, false);
+	}
+	put_device(d);
+
+	return 0;
+}
+
 static int __maybe_unused amd_pmc_suspend(struct device *dev)
 {
 	struct amd_pmc_dev *pdev = dev_get_drvdata(dev);
 	int rc;
 	u8 msg;
+	u32 arg = 1;
+
+	if (pdev->cpu_id == AMD_CPU_ID_CZN) {
+		int rc = amd_pmc_czn_wa_irq1(pdev);
+
+		if (rc) {
+			dev_err(pdev->dev, "failed to adjust keyboard wakeup: %d\n", rc);
+			return rc;
+		}
+	}
 
 	/* Reset and Start SMU logging - to monitor the s0i3 stats */
 	amd_pmc_send_cmd(pdev, 0, NULL, SMU_MSG_LOG_RESET, 0);
 	amd_pmc_send_cmd(pdev, 0, NULL, SMU_MSG_LOG_START, 0);
 
+	/* Activate CZN specific RTC functionality */
+	if (pdev->cpu_id == AMD_CPU_ID_CZN) {
+		rc = amd_pmc_verify_czn_rtc(pdev, &arg);
+		if (rc < 0)
+			return rc;
+	}
+
+	/* Dump the IdleMask before we send hint to SMU */
+	amd_pmc_idlemask_read(pdev, dev, NULL);
 	msg = amd_pmc_get_os_hint(pdev);
-	rc = amd_pmc_send_cmd(pdev, 1, NULL, msg, 0);
+	rc = amd_pmc_send_cmd(pdev, arg, NULL, msg, 0);
 	if (rc)
 		dev_err(pdev->dev, "suspend failed\n");
 
@@ -371,11 +541,15 @@
 	if (rc)
 		dev_err(pdev->dev, "resume failed\n");
 
+	/* Dump the IdleMask to see the blockers */
+	amd_pmc_idlemask_read(pdev, dev, NULL);
+
 	return 0;
 }
 
 static const struct dev_pm_ops amd_pmc_pm_ops = {
-	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(amd_pmc_suspend, amd_pmc_resume)
+	.suspend_noirq = amd_pmc_suspend,
+	.resume_noirq = amd_pmc_resume,
 };
 
 static const struct pci_device_id pmc_pci_ids[] = {
@@ -457,6 +631,7 @@
 	if (err)
 		dev_err(dev->dev, "SMU debugging info not supported on this platform\n");
 
+	amd_pmc_get_smu_version(dev);
 	platform_set_drvdata(pdev, dev);
 	amd_pmc_dbgfs_register(dev);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/apple-gmux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/apple-gmux.c
@@ -625,7 +625,7 @@
 	}
 
 	gmux_data->iostart = res->start;
-	gmux_data->iolen = res->end - res->start;
+	gmux_data->iolen = resource_size(res);
 
 	if (gmux_data->iolen < GMUX_MIN_IO_LEN) {
 		pr_err("gmux I/O region too small (%lu < %u)\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/asus-nb-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/asus-nb-wmi.c
@@ -115,12 +115,17 @@
 };
 
 static struct quirk_entry quirk_asus_use_kbd_dock_devid = {
-	.use_kbd_dock_devid = true,
+	.tablet_switch_mode = asus_wmi_kbd_dock_devid,
 };
 
 static struct quirk_entry quirk_asus_use_lid_flip_devid = {
 	.wmi_backlight_set_devstate = true,
-	.use_lid_flip_devid = true,
+	.tablet_switch_mode = asus_wmi_lid_flip_devid,
+};
+
+static struct quirk_entry quirk_asus_tablet_mode = {
+	.wmi_backlight_set_devstate = true,
+	.tablet_switch_mode = asus_wmi_lid_flip_rog_devid,
 };
 
 static int dmi_matched(const struct dmi_system_id *dmi)
@@ -471,13 +476,20 @@
 		},
 		.driver_data = &quirk_asus_use_lid_flip_devid,
 	},
+	{
+		.callback = dmi_matched,
+		.ident = "ASUS ROG FLOW X13",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "GV301Q"),
+		},
+		.driver_data = &quirk_asus_tablet_mode,
+	},
 	{},
 };
 
 static void asus_nb_wmi_quirks(struct asus_wmi_driver *driver)
 {
-	int ret;
-
 	quirks = &quirk_asus_unknown;
 	dmi_check_system(asus_quirks);
 
@@ -490,37 +502,20 @@
 	else
 		wapf = quirks->wapf;
 
-	switch (tablet_mode_sw) {
-	case 0:
-		quirks->use_kbd_dock_devid = false;
-		quirks->use_lid_flip_devid = false;
-		break;
-	case 1:
-		quirks->use_kbd_dock_devid = true;
-		quirks->use_lid_flip_devid = false;
-		break;
-	case 2:
-		quirks->use_kbd_dock_devid = false;
-		quirks->use_lid_flip_devid = true;
-		break;
-	}
-
-	if (quirks->i8042_filter) {
-		ret = i8042_install_filter(quirks->i8042_filter);
-		if (ret) {
-			pr_warn("Unable to install key filter\n");
-			return;
-		}
-		pr_info("Using i8042 filter function for receiving events\n");
-	}
+	if (tablet_mode_sw != -1)
+		quirks->tablet_switch_mode = tablet_mode_sw;
 }
 
 static const struct key_entry asus_nb_wmi_keymap[] = {
 	{ KE_KEY, ASUS_WMI_BRN_DOWN, { KEY_BRIGHTNESSDOWN } },
 	{ KE_KEY, ASUS_WMI_BRN_UP, { KEY_BRIGHTNESSUP } },
+	{ KE_KEY, 0x2a, { KEY_SELECTIVE_SCREENSHOT } },
+	{ KE_IGNORE, 0x2b, }, /* PrintScreen (also send via PS/2) on newer models */
+	{ KE_IGNORE, 0x2c, }, /* CapsLock (also send via PS/2) on newer models */
 	{ KE_KEY, 0x30, { KEY_VOLUMEUP } },
 	{ KE_KEY, 0x31, { KEY_VOLUMEDOWN } },
 	{ KE_KEY, 0x32, { KEY_MUTE } },
+	{ KE_KEY, 0x33, { KEY_SCREENLOCK } },
 	{ KE_KEY, 0x35, { KEY_SCREENLOCK } },
 	{ KE_KEY, 0x40, { KEY_PREVIOUSSONG } },
 	{ KE_KEY, 0x41, { KEY_NEXTSONG } },
@@ -549,6 +544,7 @@
 	{ KE_KEY, 0x71, { KEY_F13 } }, /* General-purpose button */
 	{ KE_IGNORE, 0x79, },  /* Charger type dectection notification */
 	{ KE_KEY, 0x7a, { KEY_ALS_TOGGLE } }, /* Ambient Light Sensor Toggle */
+	{ KE_IGNORE, 0x7B, }, /* Charger connect/disconnect notification */
 	{ KE_KEY, 0x7c, { KEY_MICMUTE } },
 	{ KE_KEY, 0x7D, { KEY_BLUETOOTH } }, /* Bluetooth Enable */
 	{ KE_KEY, 0x7E, { KEY_BLUETOOTH } }, /* Bluetooth Disable */
@@ -574,10 +570,13 @@
 	{ KE_KEY, 0xA6, { KEY_SWITCHVIDEOMODE } }, /* SDSP CRT + TV + HDMI */
 	{ KE_KEY, 0xA7, { KEY_SWITCHVIDEOMODE } }, /* SDSP LCD + CRT + TV + HDMI */
 	{ KE_KEY, 0xB5, { KEY_CALC } },
+	{ KE_IGNORE, 0xC0, }, /* External display connect/disconnect notification */
 	{ KE_KEY, 0xC4, { KEY_KBDILLUMUP } },
 	{ KE_KEY, 0xC5, { KEY_KBDILLUMDOWN } },
 	{ KE_IGNORE, 0xC6, },  /* Ambient Light Sensor notification */
+	{ KE_IGNORE, 0xCF, },	/* AC mode */
 	{ KE_KEY, 0xFA, { KEY_PROG2 } },           /* Lid flip action */
+	{ KE_KEY, 0xBD, { KEY_PROG2 } },           /* Lid flip action on ROG xflow laptops */
 	{ KE_END, 0},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/asus-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/asus-wmi.c
@@ -68,6 +68,7 @@
 #define NOTIFY_KBD_FBM			0x99
 #define NOTIFY_KBD_TTP			0xae
 #define NOTIFY_LID_FLIP			0xfa
+#define NOTIFY_LID_FLIP_ROG		0xbd
 
 #define ASUS_WMI_FNLOCK_BIOS_DISABLED	BIT(0)
 
@@ -203,6 +204,10 @@
 	struct asus_rfkill gps;
 	struct asus_rfkill uwb;
 
+	int tablet_switch_event_code;
+	u32 tablet_switch_dev_id;
+	bool tablet_switch_inverted;
+
 	enum fan_type fan_type;
 	int fan_pwm_mode;
 	int agfn_pwm;
@@ -316,7 +321,17 @@
 
 static int asus_wmi_get_devstate(struct asus_wmi *asus, u32 dev_id, u32 *retval)
 {
-	return asus_wmi_evaluate_method(asus->dsts_id, dev_id, 0, retval);
+	int err;
+
+	err = asus_wmi_evaluate_method(asus->dsts_id, dev_id, 0, retval);
+
+	if (err)
+		return err;
+
+	if (*retval == ~0)
+		return -ENODEV;
+
+	return 0;
 }
 
 static int asus_wmi_set_devstate(u32 dev_id, u32 ctrl_param,
@@ -363,10 +378,35 @@
 }
 
 /* Input **********************************************************************/
+static void asus_wmi_tablet_sw_report(struct asus_wmi *asus, bool value)
+{
+	input_report_switch(asus->inputdev, SW_TABLET_MODE,
+			    asus->tablet_switch_inverted ? !value : value);
+	input_sync(asus->inputdev);
+}
+
+static void asus_wmi_tablet_sw_init(struct asus_wmi *asus, u32 dev_id, int event_code)
+{
+	struct device *dev = &asus->platform_device->dev;
+	int result;
+
+	result = asus_wmi_get_devstate_simple(asus, dev_id);
+	if (result >= 0) {
+		input_set_capability(asus->inputdev, EV_SW, SW_TABLET_MODE);
+		asus_wmi_tablet_sw_report(asus, result);
+		asus->tablet_switch_dev_id = dev_id;
+		asus->tablet_switch_event_code = event_code;
+	} else if (result == -ENODEV) {
+		dev_err(dev, "This device has tablet-mode-switch quirk but got ENODEV checking it. This is a bug.");
+	} else {
+		dev_err(dev, "Error checking for tablet-mode-switch: %d\n", result);
+	}
+}
 
 static int asus_wmi_input_init(struct asus_wmi *asus)
 {
-	int err, result;
+	struct device *dev = &asus->platform_device->dev;
+	int err;
 
 	asus->inputdev = input_allocate_device();
 	if (!asus->inputdev)
@@ -375,35 +415,26 @@
 	asus->inputdev->name = asus->driver->input_name;
 	asus->inputdev->phys = asus->driver->input_phys;
 	asus->inputdev->id.bustype = BUS_HOST;
-	asus->inputdev->dev.parent = &asus->platform_device->dev;
+	asus->inputdev->dev.parent = dev;
 	set_bit(EV_REP, asus->inputdev->evbit);
 
 	err = sparse_keymap_setup(asus->inputdev, asus->driver->keymap, NULL);
 	if (err)
 		goto err_free_dev;
 
-	if (asus->driver->quirks->use_kbd_dock_devid) {
-		result = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_KBD_DOCK);
-		if (result >= 0) {
-			input_set_capability(asus->inputdev, EV_SW, SW_TABLET_MODE);
-			input_report_switch(asus->inputdev, SW_TABLET_MODE, !result);
-		} else if (result != -ENODEV) {
-			pr_err("Error checking for keyboard-dock: %d\n", result);
-		}
-	}
-
-	if (asus->driver->quirks->use_lid_flip_devid) {
-		result = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_LID_FLIP);
-		if (result < 0)
-			asus->driver->quirks->use_lid_flip_devid = 0;
-		if (result >= 0) {
-			input_set_capability(asus->inputdev, EV_SW, SW_TABLET_MODE);
-			input_report_switch(asus->inputdev, SW_TABLET_MODE, result);
-		} else if (result == -ENODEV) {
-			pr_err("This device has lid_flip quirk but got ENODEV checking it. This is a bug.");
-		} else {
-			pr_err("Error checking for lid-flip: %d\n", result);
-		}
+	switch (asus->driver->quirks->tablet_switch_mode) {
+	case asus_wmi_no_tablet_switch:
+		break;
+	case asus_wmi_kbd_dock_devid:
+		asus->tablet_switch_inverted = true;
+		asus_wmi_tablet_sw_init(asus, ASUS_WMI_DEVID_KBD_DOCK, NOTIFY_KBD_DOCK_CHANGE);
+		break;
+	case asus_wmi_lid_flip_devid:
+		asus_wmi_tablet_sw_init(asus, ASUS_WMI_DEVID_LID_FLIP, NOTIFY_LID_FLIP);
+		break;
+	case asus_wmi_lid_flip_rog_devid:
+		asus_wmi_tablet_sw_init(asus, ASUS_WMI_DEVID_LID_FLIP_ROG, NOTIFY_LID_FLIP_ROG);
+		break;
 	}
 
 	err = input_register_device(asus->inputdev);
@@ -427,14 +458,16 @@
 
 /* Tablet mode ****************************************************************/
 
-static void lid_flip_tablet_mode_get_state(struct asus_wmi *asus)
+static void asus_wmi_tablet_mode_get_state(struct asus_wmi *asus)
 {
-	int result = asus_wmi_get_devstate_simple(asus, ASUS_WMI_DEVID_LID_FLIP);
+	int result;
 
-	if (result >= 0) {
-		input_report_switch(asus->inputdev, SW_TABLET_MODE, result);
-		input_sync(asus->inputdev);
-	}
+	if (!asus->tablet_switch_dev_id)
+		return;
+
+	result = asus_wmi_get_devstate_simple(asus, asus->tablet_switch_dev_id);
+	if (result >= 0)
+		asus_wmi_tablet_sw_report(asus, result);
 }
 
 /* dGPU ********************************************************************/
@@ -1511,6 +1544,8 @@
 	pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
 				cpu_to_le32(ports_available));
 
+	pci_dev_put(xhci_pdev);
+
 	pr_info("set USB_INTEL_XUSB2PR old: 0x%04x, new: 0x%04x\n",
 			orig_ports_available, ports_available);
 }
@@ -2484,9 +2519,7 @@
 {
 	unsigned int key_value = 1;
 	bool autorelease = 1;
-	int result, orig_code;
-
-	orig_code = code;
+	int orig_code = code;
 
 	if (asus->driver->key_filter) {
 		asus->driver->key_filter(asus->driver, &code, &key_value,
@@ -2529,19 +2562,8 @@
 		return;
 	}
 
-	if (asus->driver->quirks->use_kbd_dock_devid && code == NOTIFY_KBD_DOCK_CHANGE) {
-		result = asus_wmi_get_devstate_simple(asus,
-						      ASUS_WMI_DEVID_KBD_DOCK);
-		if (result >= 0) {
-			input_report_switch(asus->inputdev, SW_TABLET_MODE,
-					    !result);
-			input_sync(asus->inputdev);
-		}
-		return;
-	}
-
-	if (asus->driver->quirks->use_lid_flip_devid && code == NOTIFY_LID_FLIP) {
-		lid_flip_tablet_mode_get_state(asus);
+	if (code == asus->tablet_switch_event_code) {
+		asus_wmi_tablet_mode_get_state(asus);
 		return;
 	}
 
@@ -3087,6 +3109,12 @@
 		goto fail_wmi_handler;
 	}
 
+	if (asus->driver->quirks->i8042_filter) {
+		err = i8042_install_filter(asus->driver->quirks->i8042_filter);
+		if (err)
+			pr_warn("Unable to install key filter - %d\n", err);
+	}
+
 	asus_wmi_battery_init(asus);
 
 	asus_wmi_debugfs_init(asus);
@@ -3123,6 +3151,8 @@
 	struct asus_wmi *asus;
 
 	asus = platform_get_drvdata(device);
+	if (asus->driver->quirks->i8042_filter)
+		i8042_remove_filter(asus->driver->quirks->i8042_filter);
 	wmi_remove_notify_handler(asus->driver->event_guid);
 	asus_wmi_backlight_exit(asus);
 	asus_wmi_input_exit(asus);
@@ -3171,9 +3201,7 @@
 	if (asus_wmi_has_fnlock_key(asus))
 		asus_wmi_fnlock_update(asus);
 
-	if (asus->driver->quirks->use_lid_flip_devid)
-		lid_flip_tablet_mode_get_state(asus);
-
+	asus_wmi_tablet_mode_get_state(asus);
 	return 0;
 }
 
@@ -3213,9 +3241,7 @@
 	if (asus_wmi_has_fnlock_key(asus))
 		asus_wmi_fnlock_update(asus);
 
-	if (asus->driver->quirks->use_lid_flip_devid)
-		lid_flip_tablet_mode_get_state(asus);
-
+	asus_wmi_tablet_mode_get_state(asus);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/asus-wmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/asus-wmi.h
@@ -18,13 +18,20 @@
 #include <linux/i8042.h>
 
 #define ASUS_WMI_KEY_IGNORE (-1)
-#define ASUS_WMI_BRN_DOWN	0x20
+#define ASUS_WMI_BRN_DOWN	0x2e
 #define ASUS_WMI_BRN_UP		0x2f
 
 struct module;
 struct key_entry;
 struct asus_wmi;
 
+enum asus_wmi_tablet_switch_mode {
+	asus_wmi_no_tablet_switch,
+	asus_wmi_kbd_dock_devid,
+	asus_wmi_lid_flip_devid,
+	asus_wmi_lid_flip_rog_devid,
+};
+
 struct quirk_entry {
 	bool hotplug_wireless;
 	bool scalar_panel_brightness;
@@ -33,8 +40,7 @@
 	bool wmi_backlight_native;
 	bool wmi_backlight_set_devstate;
 	bool wmi_force_als_set;
-	bool use_kbd_dock_devid;
-	bool use_lid_flip_devid;
+	enum asus_wmi_tablet_switch_mode tablet_switch_mode;
 	int wapf;
 	/*
 	 * For machines with AMD graphic chips, it will send out WMI event
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/Kconfig
@@ -187,7 +187,7 @@
 
 config DELL_WMI_DESCRIPTOR
 	tristate
-	default m
+	default n
 	depends on ACPI_WMI
 
 config DELL_WMI_LED
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/Makefile
@@ -14,6 +14,7 @@
 dell-smbios-$(CONFIG_DELL_SMBIOS_WMI)	+= dell-smbios-wmi.o
 dell-smbios-$(CONFIG_DELL_SMBIOS_SMM)	+= dell-smbios-smm.o
 obj-$(CONFIG_DELL_SMO8800)		+= dell-smo8800.o
+obj-$(CONFIG_DELL_UART_BACKLIGHT)	+= dell-uart-backlight.o
 obj-$(CONFIG_DELL_WMI)			+= dell-wmi.o
 dell-wmi-objs				:= dell-wmi-base.o
 dell-wmi-$(CONFIG_DELL_WMI_PRIVACY)	+= dell-wmi-privacy.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-laptop.c
@@ -93,6 +93,7 @@
 static struct rfkill *wwan_rfkill;
 static bool force_rfkill;
 static bool micmute_led_registered;
+static bool mute_led_registered;
 
 module_param(force_rfkill, bool, 0444);
 MODULE_PARM_DESC(force_rfkill, "enable rfkill on non whitelisted models");
@@ -2164,6 +2165,34 @@
 	.default_trigger = "audio-micmute",
 };
 
+static int mute_led_set(struct led_classdev *led_cdev,
+			   enum led_brightness brightness)
+{
+	struct calling_interface_buffer buffer;
+	struct calling_interface_token *token;
+	int state = brightness != LED_OFF;
+
+	if (state == 0)
+		token = dell_smbios_find_token(GLOBAL_MUTE_DISABLE);
+	else
+		token = dell_smbios_find_token(GLOBAL_MUTE_ENABLE);
+
+	if (!token)
+		return -ENODEV;
+
+	dell_fill_request(&buffer, token->location, token->value, 0, 0);
+	dell_send_request(&buffer, CLASS_TOKEN_WRITE, SELECT_TOKEN_STD);
+
+	return 0;
+}
+
+static struct led_classdev mute_led_cdev = {
+	.name = "platform::mute",
+	.max_brightness = 1,
+	.brightness_set_blocking = mute_led_set,
+	.default_trigger = "audio-mute",
+};
+
 static int __init dell_init(void)
 {
 	struct calling_interface_token *token;
@@ -2217,6 +2246,15 @@
 		micmute_led_registered = true;
 	}
 
+	if (dell_smbios_find_token(GLOBAL_MUTE_DISABLE) &&
+	    dell_smbios_find_token(GLOBAL_MUTE_ENABLE)) {
+		mute_led_cdev.brightness = ledtrig_audio_get(LED_AUDIO_MUTE);
+		ret = led_classdev_register(&platform_device->dev, &mute_led_cdev);
+		if (ret < 0)
+			goto fail_backlight;
+		mute_led_registered = true;
+	}
+
 	if (acpi_video_get_backlight_type() != acpi_backlight_vendor)
 		return 0;
 
@@ -2264,6 +2302,8 @@
 fail_backlight:
 	if (micmute_led_registered)
 		led_classdev_unregister(&micmute_led_cdev);
+	if (mute_led_registered)
+		led_classdev_unregister(&mute_led_cdev);
 fail_led:
 	dell_cleanup_rfkill();
 fail_rfkill:
@@ -2286,6 +2326,8 @@
 	backlight_device_unregister(dell_backlight_device);
 	if (micmute_led_registered)
 		led_classdev_unregister(&micmute_led_cdev);
+	if (mute_led_registered)
+		led_classdev_unregister(&mute_led_cdev);
 	dell_cleanup_rfkill();
 	if (platform_device) {
 		platform_device_unregister(platform_device);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-smbios-base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-smbios-base.c
@@ -25,11 +25,16 @@
 static int da_num_tokens;
 static struct platform_device *platform_device;
 static struct calling_interface_token *da_tokens;
-static struct device_attribute *token_location_attrs;
-static struct device_attribute *token_value_attrs;
+static struct token_sysfs_data *token_entries;
 static struct attribute **token_attrs;
 static DEFINE_MUTEX(smbios_mutex);
 
+struct token_sysfs_data {
+	struct device_attribute location_attr;
+	struct device_attribute value_attr;
+	struct calling_interface_token *token;
+};
+
 struct smbios_device {
 	struct list_head list;
 	struct device *device;
@@ -416,47 +421,26 @@
 	}
 }
 
-static int match_attribute(struct device *dev,
-			   struct device_attribute *attr)
-{
-	int i;
-
-	for (i = 0; i < da_num_tokens * 2; i++) {
-		if (!token_attrs[i])
-			continue;
-		if (strcmp(token_attrs[i]->name, attr->attr.name) == 0)
-			return i/2;
-	}
-	dev_dbg(dev, "couldn't match: %s\n", attr->attr.name);
-	return -EINVAL;
-}
-
 static ssize_t location_show(struct device *dev,
 			     struct device_attribute *attr, char *buf)
 {
-	int i;
+	struct token_sysfs_data *data = container_of(attr, struct token_sysfs_data, location_attr);
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
 
-	i = match_attribute(dev, attr);
-	if (i > 0)
-		return scnprintf(buf, PAGE_SIZE, "%08x", da_tokens[i].location);
-	return 0;
+	return sysfs_emit(buf, "%08x", data->token->location);
 }
 
 static ssize_t value_show(struct device *dev,
 			  struct device_attribute *attr, char *buf)
 {
-	int i;
+	struct token_sysfs_data *data = container_of(attr, struct token_sysfs_data, value_attr);
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
 
-	i = match_attribute(dev, attr);
-	if (i > 0)
-		return scnprintf(buf, PAGE_SIZE, "%08x", da_tokens[i].value);
-	return 0;
+	return sysfs_emit(buf, "%08x", data->token->value);
 }
 
 static struct attribute_group smbios_attribute_group = {
@@ -473,22 +457,15 @@
 {
 	char *location_name;
 	char *value_name;
-	size_t size;
 	int ret;
 	int i, j;
 
-	/* (number of tokens  + 1 for null terminated */
-	size = sizeof(struct device_attribute) * (da_num_tokens + 1);
-	token_location_attrs = kzalloc(size, GFP_KERNEL);
-	if (!token_location_attrs)
+	token_entries = kcalloc(da_num_tokens, sizeof(*token_entries), GFP_KERNEL);
+	if (!token_entries)
 		return -ENOMEM;
-	token_value_attrs = kzalloc(size, GFP_KERNEL);
-	if (!token_value_attrs)
-		goto out_allocate_value;
 
 	/* need to store both location and value + terminator*/
-	size = sizeof(struct attribute *) * ((2 * da_num_tokens) + 1);
-	token_attrs = kzalloc(size, GFP_KERNEL);
+	token_attrs = kcalloc((2 * da_num_tokens) + 1, sizeof(*token_attrs), GFP_KERNEL);
 	if (!token_attrs)
 		goto out_allocate_attrs;
 
@@ -496,27 +473,32 @@
 		/* skip empty */
 		if (da_tokens[i].tokenID == 0)
 			continue;
+
+		token_entries[i].token = &da_tokens[i];
+
 		/* add location */
 		location_name = kasprintf(GFP_KERNEL, "%04x_location",
 					  da_tokens[i].tokenID);
 		if (location_name == NULL)
 			goto out_unwind_strings;
-		sysfs_attr_init(&token_location_attrs[i].attr);
-		token_location_attrs[i].attr.name = location_name;
-		token_location_attrs[i].attr.mode = 0444;
-		token_location_attrs[i].show = location_show;
-		token_attrs[j++] = &token_location_attrs[i].attr;
+
+		sysfs_attr_init(&token_entries[i].location_attr.attr);
+		token_entries[i].location_attr.attr.name = location_name;
+		token_entries[i].location_attr.attr.mode = 0444;
+		token_entries[i].location_attr.show = location_show;
+		token_attrs[j++] = &token_entries[i].location_attr.attr;
 
 		/* add value */
 		value_name = kasprintf(GFP_KERNEL, "%04x_value",
 				       da_tokens[i].tokenID);
 		if (value_name == NULL)
 			goto loop_fail_create_value;
-		sysfs_attr_init(&token_value_attrs[i].attr);
-		token_value_attrs[i].attr.name = value_name;
-		token_value_attrs[i].attr.mode = 0444;
-		token_value_attrs[i].show = value_show;
-		token_attrs[j++] = &token_value_attrs[i].attr;
+
+		sysfs_attr_init(&token_entries[i].value_attr.attr);
+		token_entries[i].value_attr.attr.name = value_name;
+		token_entries[i].value_attr.attr.mode = 0444;
+		token_entries[i].value_attr.show = value_show;
+		token_attrs[j++] = &token_entries[i].value_attr.attr;
 		continue;
 
 loop_fail_create_value:
@@ -532,14 +514,12 @@
 
 out_unwind_strings:
 	while (i--) {
-		kfree(token_location_attrs[i].attr.name);
-		kfree(token_value_attrs[i].attr.name);
+		kfree(token_entries[i].location_attr.attr.name);
+		kfree(token_entries[i].value_attr.attr.name);
 	}
 	kfree(token_attrs);
 out_allocate_attrs:
-	kfree(token_value_attrs);
-out_allocate_value:
-	kfree(token_location_attrs);
+	kfree(token_entries);
 
 	return -ENOMEM;
 }
@@ -551,12 +531,11 @@
 	sysfs_remove_group(&pdev->dev.kobj,
 				&smbios_attribute_group);
 	for (i = 0; i < da_num_tokens; i++) {
-		kfree(token_location_attrs[i].attr.name);
-		kfree(token_value_attrs[i].attr.name);
+		kfree(token_entries[i].location_attr.attr.name);
+		kfree(token_entries[i].value_attr.attr.name);
 	}
 	kfree(token_attrs);
-	kfree(token_value_attrs);
-	kfree(token_location_attrs);
+	kfree(token_entries);
 }
 
 static int __init dell_smbios_init(void)
@@ -564,6 +543,7 @@
 	int ret, wmi, smm;
 
 	if (!dmi_find_device(DMI_DEV_TYPE_OEM_STRING, "Dell System", NULL) &&
+	    !dmi_find_device(DMI_DEV_TYPE_OEM_STRING, "Alienware", NULL) &&
 	    !dmi_find_device(DMI_DEV_TYPE_OEM_STRING, "www.dell.com", NULL)) {
 		pr_err("Unable to run on non-Dell system\n");
 		return -ENODEV;
@@ -610,7 +590,10 @@
 	return 0;
 
 fail_sysfs:
-	free_group(platform_device);
+	if (!wmi)
+		exit_dell_smbios_wmi();
+	if (!smm)
+		exit_dell_smbios_smm();
 
 fail_create_group:
 	platform_device_del(platform_device);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-smbios.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-smbios.h
@@ -34,6 +34,8 @@
 #define KBD_LED_AUTO_100_TOKEN	0x02F6
 #define GLOBAL_MIC_MUTE_ENABLE	0x0364
 #define GLOBAL_MIC_MUTE_DISABLE	0x0365
+#define GLOBAL_MUTE_ENABLE	0x058C
+#define GLOBAL_MUTE_DISABLE	0x058D
 
 struct notifier_block;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-uart-backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-uart-backlight.c
@@ -0,0 +1,531 @@
+/*
+ *  Dell AIO Serial Backlight Driver
+ *
+ *  Copyright (C) 2017 AceLan Kao <acelan.kao@canonical.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/acpi.h>
+#include <linux/serial_8250.h>
+#include <linux/delay.h>
+#include <linux/backlight.h>
+#include <linux/dmi.h>
+#include <acpi/video.h>
+
+#include "dell-uart-backlight.h"
+
+struct dell_uart_backlight {
+	struct device *dev;
+	struct backlight_device *dell_uart_bd;
+	struct mutex brightness_mutex;
+	int line;
+	int bl_power;
+};
+struct uart_8250_port *serial8250_get_port(int line);
+static struct tty_struct *tty;
+static struct file *ftty;
+
+unsigned int (*io_serial_in)(struct uart_port *p, int offset);
+int (*uart_write)(struct tty_struct *tty, const unsigned char *buf, int count);
+unsigned int (*uart_chars_in_buffer)(struct tty_struct *tty);
+
+static bool force;
+module_param(force, bool, 0444);
+MODULE_PARM_DESC(force, "load the driver regardless of the scalar status");
+
+static struct dell_uart_bl_cmd uart_cmd[] = {
+	/*
+	 * Get Firmware Version: Tool uses this command to get firmware version.
+	 * Command: 0x6A 0x06 0x8F (Length:3 Type: 0x0A, Cmd:6 Checksum:0x8F)
+	 * Return data: 0x0D 0x06 Data checksum (Length:13,Cmd:0x06,
+	 *              Data :F/W version(APRILIA=APR27-VXXX,PHINE=PHI23-VXXX),
+	 *              checksum:SUM(Length and Cmd and Data)xor 0xFF .
+	 */
+	[DELL_UART_GET_FIRMWARE_VER] = {
+		.cmd	= {0x6A, 0x06, 0x8F},
+		.tx_len	= 3,
+	},
+	/*
+	 * Get Brightness level: Application uses this command for scaler to
+	 *                       get brightness.
+	 * Command: 0x6A 0x0C 0x89
+	 *          (Length:3 Type: 0x0A, Cmd:0x0C, Checksum:0x89)
+	 * Return data: 0x04 0x0C Data checksum
+	 * (Length:4 Cmd: 0x0C Data: brightness level
+	 *           checksum: SUM(Length and Cmd and Data)xor 0xFF)
+	 *           brightness level which ranges from 0~100.
+	 */
+	[DELL_UART_GET_BRIGHTNESS] = {
+		.cmd	= {0x6A, 0x0C, 0x89},
+		.ret	= {0x04, 0x0C, 0x00, 0x00},
+		.tx_len	= 3,
+		.rx_len	= 4,
+	},
+	/* Set Brightness level: Application uses this command for scaler to
+	 *                       set brightness.
+	 * Command: 0x8A 0x0B Byte2 Checksum (Length:4 Type: 0x0A, Cmd:0x0B)
+	 *          where Byte2 is the brightness level which ranges from 0~100.
+	 * Return data: 0x03 0x0B 0xF1(Length:3,Cmd:B,checksum:0xF1)
+	 * Scaler must send the 3bytes ack within 1 second when success,
+	 * other value if error
+	 */
+	[DELL_UART_SET_BRIGHTNESS] = {
+		.cmd	= {0x8A, 0x0B, 0x0, 0x0},
+		.ret	= {0x03, 0x0B, 0xF1},
+		.tx_len	= 4,
+		.rx_len	= 3,
+	},
+	/*
+	 * Screen ON/OFF Control: Application uses this command to control
+	 *                        screen ON or OFF.
+	 * Command: 0x8A 0x0E Byte2 Checksum (Length:4 Type: 0x0A, Cmd:0x0E)
+	 *          where
+	 *          Byte2=0 to turn OFF the screen.
+	 *          Byte2=1 to turn ON the screen
+	 *          Other value of Byte2 is reserved and invalid.
+	 * Return data: 0x03 0x0E 0xEE(Length:3,Cmd:E,checksum:0xEE)
+	 */
+	[DELL_UART_SET_BACKLIGHT_POWER] = {
+		.cmd	= {0x8A, 0x0E, 0x00, 0x0},
+		.ret	= {0x03, 0x0E, 0xEE},
+		.tx_len	= 4,
+		.rx_len	= 3,
+	},
+	/*
+	 * Get display mode: Application uses this command to get scaler
+	 * 		     display mode.
+	 * Command: 0x6A 0x10 0x85 (Length:3 Type: 0x0A, Cmd:0x10)
+	 * Return data: 0x04 0x10 Data checksum
+	 * 		(Length:4 Cmd:0x10 Data: mode checksum: SUM
+	 *		mode =0 if PC mode
+	 *		mode =1 if AV(HDMI) mode
+	 */
+	[DELL_UART_GET_DISPLAY_MODE] = {
+		.cmd	= {0x6A, 0x10, 0x85},
+		.ret	= {0x04, 0x10, 0x00, 0x00},
+		.tx_len	= 3,
+		.rx_len	= 4,
+	},
+};
+
+static const struct dmi_system_id dell_uart_backlight_alpha_platform[] = {
+	{
+		.ident = "Dell Inspiron 7777 AIO",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Inspiron 7777 AIO"),
+		},
+	},
+	{
+		.ident = "Dell Inspiron 5477 AIO",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Inspiron 5477 AIO"),
+		},
+	},
+	{
+		.ident = "Dell OptiPlex 7769 AIO",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 7769 AIO"),
+		},
+	},
+	{
+		.ident = "Dell OptiPlex 5260 AIO",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 5260 AIO"),
+		},
+	},
+	{ }
+};
+
+static int dell_uart_write(struct uart_8250_port *up, __u8 *buf, int len)
+{
+	int actual = 0;
+	struct uart_port *port = &up->port;
+
+	tty_port_tty_wakeup(&port->state->port);
+	tty = tty_port_tty_get(&port->state->port);
+	actual = uart_write(tty, buf, len);
+	while (uart_chars_in_buffer(tty))
+		udelay(10);
+
+	return actual;
+}
+
+static int dell_uart_read(struct uart_8250_port *up, __u8 *buf, int len)
+{
+	int i, retry;
+	unsigned long flags;
+
+	spin_lock_irqsave(&up->port.lock, flags);
+	for (i = 0; i < len; i++) {
+		retry = 10;
+		while (!(io_serial_in(&up->port, UART_LSR) & UART_LSR_DR)) {
+			if (--retry == 0)
+				break;
+			mdelay(20);
+		}
+
+		if (retry == 0)
+			break;
+		buf[i] = io_serial_in(&up->port, UART_RX);
+	}
+	spin_unlock_irqrestore(&up->port.lock, flags);
+
+	return i;
+}
+
+static void dell_uart_dump_cmd(const char *func, const char *prefix,
+			       const char *cmd, int len)
+{
+	char buf[80];
+
+	snprintf(buf, 80, "dell_uart_backlight:%s:%s", func, prefix);
+	if (len != 0)
+		print_hex_dump_debug(buf, DUMP_PREFIX_NONE,
+					16, 1, cmd, len, false);
+	else
+		pr_debug("dell_uart_backlight:%s:%sNULL\n", func, prefix);
+
+}
+
+/*
+ * checksum: SUM(Length and Cmd and Data)xor 0xFF)
+ */
+static unsigned char dell_uart_checksum(unsigned char *buf, int len)
+{
+	unsigned char val = 0;
+
+	while (len-- > 0)
+		val += buf[len];
+
+	return val ^ 0xff;
+}
+
+/*
+ * There is no command to get backlight power status,
+ * so we set the backlight power to "on" while initializing,
+ * and then track and report its status by bl_power variable
+ */
+static inline int dell_uart_get_bl_power(struct dell_uart_backlight *dell_pdata)
+{
+	return dell_pdata->bl_power;
+}
+
+static int dell_uart_set_bl_power(struct backlight_device *bd, int power)
+{
+	struct dell_uart_bl_cmd *bl_cmd =
+		&uart_cmd[DELL_UART_SET_BACKLIGHT_POWER];
+	struct dell_uart_backlight *dell_pdata = bl_get_data(bd);
+	struct uart_8250_port *uart = serial8250_get_port(dell_pdata->line);
+	int rx_len;
+
+	if (power != FB_BLANK_POWERDOWN)
+		power = FB_BLANK_UNBLANK;
+
+	bl_cmd->cmd[2] = power ? 0 : 1;
+	bl_cmd->cmd[3] = dell_uart_checksum(bl_cmd->cmd, bl_cmd->tx_len - 1);
+
+	dell_uart_dump_cmd(__func__, "tx: ", bl_cmd->cmd, bl_cmd->tx_len);
+
+	if (mutex_lock_killable(&dell_pdata->brightness_mutex) < 0) {
+		pr_debug("Failed to get mutex_lock");
+		return 0;
+	}
+
+	dell_uart_write(uart, bl_cmd->cmd, bl_cmd->tx_len);
+	rx_len = dell_uart_read(uart, bl_cmd->ret, bl_cmd->rx_len);
+
+	mutex_unlock(&dell_pdata->brightness_mutex);
+
+	dell_uart_dump_cmd(__func__, "rx: ", bl_cmd->ret, rx_len);
+
+	bd->props.power = power;
+	dell_pdata->bl_power = power;
+
+	return 0;
+}
+
+static int dell_uart_get_brightness(struct backlight_device *bd)
+{
+	struct dell_uart_bl_cmd *bl_cmd = &uart_cmd[DELL_UART_GET_BRIGHTNESS];
+	struct dell_uart_backlight *dell_pdata = bl_get_data(bd);
+	struct uart_8250_port *uart = serial8250_get_port(dell_pdata->line);
+	int rx_len, brightness = 0;
+
+	dell_uart_dump_cmd(__func__, "tx: ", bl_cmd->cmd, bl_cmd->tx_len);
+
+	if (mutex_lock_killable(&dell_pdata->brightness_mutex) < 0) {
+		pr_debug("Failed to get mutex_lock");
+		return 0;
+	}
+
+	dell_uart_write(uart, bl_cmd->cmd, bl_cmd->tx_len);
+	rx_len = dell_uart_read(uart, bl_cmd->ret, bl_cmd->rx_len);
+
+	mutex_unlock(&dell_pdata->brightness_mutex);
+
+	dell_uart_dump_cmd(__func__, "rx: ", bl_cmd->ret, rx_len);
+
+	brightness = (unsigned int)bl_cmd->ret[2];
+
+	return brightness;
+}
+
+static int dell_uart_update_status(struct backlight_device *bd)
+{
+	struct dell_uart_bl_cmd *bl_cmd = &uart_cmd[DELL_UART_SET_BRIGHTNESS];
+	struct dell_uart_backlight *dell_pdata = bl_get_data(bd);
+	struct uart_8250_port *uart = serial8250_get_port(dell_pdata->line);
+	int rx_len;
+
+	bl_cmd->cmd[2] = bd->props.brightness;
+	bl_cmd->cmd[3] = dell_uart_checksum(bl_cmd->cmd, bl_cmd->tx_len - 1);
+
+	dell_uart_dump_cmd(__func__, "tx: ", bl_cmd->cmd, bl_cmd->tx_len);
+
+	if (mutex_lock_killable(&dell_pdata->brightness_mutex) < 0) {
+		pr_debug("Failed to get mutex_lock");
+		return 0;
+	}
+
+	dell_uart_write(uart, bl_cmd->cmd, bl_cmd->tx_len);
+	rx_len = dell_uart_read(uart, bl_cmd->ret, bl_cmd->rx_len);
+
+	mutex_unlock(&dell_pdata->brightness_mutex);
+
+	dell_uart_dump_cmd(__func__, "rx: ", bl_cmd->ret, rx_len);
+
+	if (bd->props.power != dell_uart_get_bl_power(dell_pdata))
+		dell_uart_set_bl_power(bd, bd->props.power);
+
+	return 0;
+}
+
+static int dell_uart_show_firmware_ver(struct dell_uart_backlight *dell_pdata)
+{
+	struct dell_uart_bl_cmd *bl_cmd = &uart_cmd[DELL_UART_GET_FIRMWARE_VER];
+	struct uart_8250_port *uart = serial8250_get_port(dell_pdata->line);
+	int rx_len = 0, retry = 10;
+
+	dell_uart_dump_cmd(__func__, "tx: ", bl_cmd->cmd, bl_cmd->tx_len);
+
+	if (mutex_lock_killable(&dell_pdata->brightness_mutex) < 0) {
+		pr_debug("Failed to get mutex_lock");
+		return -1;
+	}
+
+	dell_uart_write(uart, bl_cmd->cmd, bl_cmd->tx_len);
+	while (retry-- > 0) {
+		/* first byte is data length */
+		dell_uart_read(uart, bl_cmd->ret, 1);
+		rx_len = (int)bl_cmd->ret[0];
+		if (bl_cmd->ret[0] > 80 || bl_cmd->ret[0] == 0) {
+			pr_debug("Failed to get firmware version\n");
+			if (retry == 0) {
+				mutex_unlock(&dell_pdata->brightness_mutex);
+				return -1;
+			}
+			msleep(100);
+			continue;
+		}
+
+		dell_uart_read(uart, bl_cmd->ret+1, rx_len-1);
+		break;
+	}
+	mutex_unlock(&dell_pdata->brightness_mutex);
+
+	dell_uart_dump_cmd(__func__, "rx: ", bl_cmd->ret, rx_len);
+
+	pr_debug("Firmare str(%d)= %s\n", (int)bl_cmd->ret[0], bl_cmd->ret+2);
+	return rx_len;
+}
+
+static int dell_uart_get_display_mode(struct dell_uart_backlight *dell_pdata)
+{
+	struct dell_uart_bl_cmd *bl_cmd = &uart_cmd[DELL_UART_GET_DISPLAY_MODE];
+	struct uart_8250_port *uart = serial8250_get_port(dell_pdata->line);
+	int rx_len;
+	int status = 0, retry = 10;
+
+	do {
+		dell_uart_dump_cmd(__func__, "tx: ", bl_cmd->cmd, bl_cmd->tx_len);
+
+		if (mutex_lock_killable(&dell_pdata->brightness_mutex) < 0) {
+			pr_debug("Failed to get mutex_lock");
+			return 0;
+		}
+
+		dell_uart_write(uart, bl_cmd->cmd, bl_cmd->tx_len);
+		rx_len = dell_uart_read(uart, bl_cmd->ret, bl_cmd->rx_len);
+
+		mutex_unlock(&dell_pdata->brightness_mutex);
+
+		dell_uart_dump_cmd(__func__, "rx: ", bl_cmd->ret, rx_len);
+		mdelay(1000);
+	} while (rx_len == 0 && --retry);
+
+	if (rx_len == 4)
+		status = ((unsigned int)bl_cmd->ret[2] == PC_MODE);
+
+	return status;
+}
+
+static const struct backlight_ops dell_uart_backlight_ops = {
+	.get_brightness = dell_uart_get_brightness,
+	.update_status = dell_uart_update_status,
+};
+
+static int dell_uart_startup(struct dell_uart_backlight *dell_pdata)
+{
+	struct uart_8250_port *uartp;
+	struct uart_port *port;
+
+	dell_pdata->line = 0;
+	uartp = serial8250_get_port(dell_pdata->line);
+	port = &uartp->port;
+	tty = port->state->port.tty;
+	io_serial_in = port->serial_in;
+	uart_write = tty->driver->ops->write;
+	uart_chars_in_buffer = tty->driver->ops->chars_in_buffer;
+
+	return 0;
+}
+
+static int dell_uart_bl_add(struct acpi_device *dev)
+{
+	struct dell_uart_backlight *dell_pdata;
+	struct backlight_properties props;
+	struct backlight_device *dell_uart_bd;
+
+	dell_pdata = kzalloc(sizeof(struct dell_uart_backlight), GFP_KERNEL);
+	if (!dell_pdata) {
+		pr_debug("Failed to allocate memory for dell_uart_backlight\n");
+		return -ENOMEM;
+	}
+	dell_pdata->dev = &dev->dev;
+	dell_uart_startup(dell_pdata);
+	dev->driver_data = dell_pdata;
+
+	mutex_init(&dell_pdata->brightness_mutex);
+
+	if (!force) {
+		if (dmi_check_system(dell_uart_backlight_alpha_platform)) {
+			/* try another command to make sure there is no scalar IC */
+			if (dell_uart_show_firmware_ver(dell_pdata) <= 4) {
+				pr_debug("Scalar is not in charge of brightness adjustment.\n");
+				kfree_sensitive(dell_pdata);
+				return -ENODEV;
+			}
+		}
+		else if (!dell_uart_get_display_mode(dell_pdata)) {
+			pr_debug("Scalar is not in charge of brightness adjustment.\n");
+			kfree_sensitive(dell_pdata);
+			return -ENODEV;
+		}
+	}
+
+	memset(&props, 0, sizeof(struct backlight_properties));
+	props.type = BACKLIGHT_PLATFORM;
+	props.max_brightness = 100;
+
+	dell_uart_bd = backlight_device_register("dell_uart_backlight",
+						 &dev->dev,
+						 dell_pdata,
+						 &dell_uart_backlight_ops,
+						 &props);
+	if (IS_ERR(dell_uart_bd)) {
+		kfree_sensitive(dell_pdata);
+		pr_debug("Backlight registration failed\n");
+		return PTR_ERR(dell_uart_bd);
+	}
+
+	dell_pdata->dell_uart_bd = dell_uart_bd;
+
+	dell_uart_set_bl_power(dell_uart_bd, FB_BLANK_UNBLANK);
+	dell_uart_bd->props.brightness = 100;
+	backlight_update_status(dell_uart_bd);
+
+	/* unregister acpi backlight interface */
+	acpi_video_set_dmi_backlight_type(acpi_backlight_vendor);
+
+	return 0;
+}
+
+static int dell_uart_bl_remove(struct acpi_device *dev)
+{
+	struct dell_uart_backlight *dell_pdata = dev->driver_data;
+
+	backlight_device_unregister(dell_pdata->dell_uart_bd);
+	kfree_sensitive(dell_pdata);
+
+	return 0;
+}
+
+static int dell_uart_bl_suspend(struct device *dev)
+{
+	filp_close(ftty, NULL);
+	return 0;
+}
+
+static int dell_uart_bl_resume(struct device *dev)
+{
+	ftty = filp_open("/dev/ttyS0", O_RDWR | O_NOCTTY | O_NDELAY, 0);
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(dell_uart_bl_pm, dell_uart_bl_suspend, dell_uart_bl_resume);
+
+static const struct acpi_device_id dell_uart_bl_ids[] = {
+	{"DELL0501", 0},
+	{"", 0},
+};
+
+static struct acpi_driver dell_uart_backlight_driver = {
+	.name = "Dell AIO serial backlight",
+	.ids = dell_uart_bl_ids,
+	.ops = {
+		.add = dell_uart_bl_add,
+		.remove = dell_uart_bl_remove,
+	},
+	.drv.pm = &dell_uart_bl_pm,
+};
+
+static int __init dell_uart_bl_init(void)
+{
+	ftty = filp_open("/dev/ttyS0", O_RDWR | O_NOCTTY | O_NDELAY, 0);
+	if (IS_ERR(ftty)) {
+		pr_debug("cannot open /dev/ttyS0\n");
+		return -EINVAL;
+	}
+
+	return acpi_bus_register_driver(&dell_uart_backlight_driver);
+}
+
+static void __exit dell_uart_bl_exit(void)
+{
+	filp_close(ftty, NULL);
+
+	acpi_bus_unregister_driver(&dell_uart_backlight_driver);
+}
+
+module_init(dell_uart_bl_init);
+module_exit(dell_uart_bl_exit);
+MODULE_DEVICE_TABLE(acpi, dell_uart_bl_ids);
+MODULE_DESCRIPTION("Dell AIO Serial Backlight module");
+MODULE_AUTHOR("AceLan Kao <acelan.kao@canonical.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-uart-backlight.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-uart-backlight.h
@@ -0,0 +1,41 @@
+/*
+ *  Dell AIO Serial Backlight Driver
+ *
+ *  Copyright (C) 2017 AceLan Kao <acelan.kao@canonical.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ */
+
+#ifndef _DELL_UART_BACKLIGHT_H_
+#define _DELL_UART_BACKLIGHT_H_
+
+enum {
+	DELL_UART_GET_FIRMWARE_VER,
+	DELL_UART_GET_BRIGHTNESS,
+	DELL_UART_SET_BRIGHTNESS,
+	DELL_UART_SET_BACKLIGHT_POWER,
+	DELL_UART_GET_DISPLAY_MODE,
+};
+
+enum {
+	PC_MODE,
+	AV_MODE,
+};
+
+struct dell_uart_bl_cmd {
+	unsigned char	cmd[10];
+	unsigned char	ret[80];
+	unsigned short	tx_len;
+	unsigned short	rx_len;
+};
+
+#endif /* _DELL_UART_BACKLIGHT_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-wmi-base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-wmi-base.c
@@ -79,6 +79,12 @@
 static const struct key_entry dell_wmi_keymap_type_0000[] = {
 	{ KE_IGNORE, 0x003a, { KEY_CAPSLOCK } },
 
+	/* Meta key lock */
+	{ KE_IGNORE, 0xe000, { KEY_RIGHTMETA } },
+
+	/* Meta key unlock */
+	{ KE_IGNORE, 0xe001, { KEY_RIGHTMETA } },
+
 	/* Key code is followed by brightness level */
 	{ KE_KEY,    0xe005, { KEY_BRIGHTNESSDOWN } },
 	{ KE_KEY,    0xe006, { KEY_BRIGHTNESSUP } },
@@ -260,6 +266,18 @@
 	{ KE_KEY,    0x57, { KEY_BRIGHTNESSDOWN } },
 	{ KE_KEY,    0x58, { KEY_BRIGHTNESSUP } },
 
+	/*Speaker Mute*/
+	{ KE_KEY, 0x109, { KEY_MUTE} },
+
+	/* S2Idle screen off */
+	{ KE_IGNORE, 0x120, { KEY_RESERVED }},
+
+	/* Leaving S4 or S2Idle suspend */
+	{ KE_IGNORE, 0x130, { KEY_RESERVED }},
+
+	/* Entering S2Idle suspend */
+	{ KE_IGNORE, 0x140, { KEY_RESERVED }},
+
 	/* Mic mute */
 	{ KE_KEY, 0x150, { KEY_MICMUTE } },
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-wmi-privacy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-wmi-privacy.c
@@ -61,7 +61,7 @@
 	/* privacy mic mute */
 	{ KE_KEY, 0x0001, { KEY_MICMUTE } },
 	/* privacy camera mute */
-	{ KE_SW,  0x0002, { SW_CAMERA_LENS_COVER } },
+	{ KE_VSW, 0x0002, { SW_CAMERA_LENS_COVER } },
 	{ KE_END, 0},
 };
 
@@ -115,11 +115,15 @@
 
 	switch (code) {
 	case DELL_PRIVACY_AUDIO_EVENT: /* Mic mute */
-	case DELL_PRIVACY_CAMERA_EVENT: /* Camera mute */
 		priv->last_status = status;
 		sparse_keymap_report_entry(priv->input_dev, key, 1, true);
 		ret = true;
 		break;
+	case DELL_PRIVACY_CAMERA_EVENT: /* Camera mute */
+		priv->last_status = status;
+		sparse_keymap_report_entry(priv->input_dev, key, !(status & CAMERA_STATUS), false);
+		ret = true;
+		break;
 	default:
 		dev_dbg(&priv->wdev->dev, "unknown event type 0x%04x 0x%04x\n", type, code);
 	}
@@ -295,7 +299,7 @@
 {
 	struct privacy_wmi_data *priv;
 	struct key_entry *keymap;
-	int ret, i;
+	int ret, i, j;
 
 	ret = wmi_has_guid(DELL_PRIVACY_GUID);
 	if (!ret)
@@ -307,6 +311,11 @@
 
 	dev_set_drvdata(&wdev->dev, priv);
 	priv->wdev = wdev;
+
+	ret = get_current_status(priv->wdev);
+	if (ret)
+		return ret;
+
 	/* create evdev passing interface */
 	priv->input_dev = devm_input_allocate_device(&wdev->dev);
 	if (!priv->input_dev)
@@ -321,9 +330,20 @@
 	/* remap the keymap code with Dell privacy key type 0x12 as prefix
 	 * KEY_MICMUTE scancode will be reported as 0x120001
 	 */
-	for (i = 0; i < ARRAY_SIZE(dell_wmi_keymap_type_0012); i++) {
-		keymap[i] = dell_wmi_keymap_type_0012[i];
-		keymap[i].code |= (0x0012 << 16);
+	for (i = 0, j = 0; i < ARRAY_SIZE(dell_wmi_keymap_type_0012); i++) {
+		/*
+		 * Unlike keys where only presses matter, userspace may act
+		 * on switches in both of their positions. Only register
+		 * SW_CAMERA_LENS_COVER if it is actually there.
+		 */
+		if (dell_wmi_keymap_type_0012[i].type == KE_VSW &&
+		    dell_wmi_keymap_type_0012[i].sw.code == SW_CAMERA_LENS_COVER &&
+		    !(priv->features_present & BIT(DELL_PRIVACY_TYPE_CAMERA)))
+			continue;
+
+		keymap[j] = dell_wmi_keymap_type_0012[i];
+		keymap[j].code |= (0x0012 << 16);
+		j++;
 	}
 	ret = sparse_keymap_setup(priv->input_dev, keymap, NULL);
 	kfree(keymap);
@@ -334,11 +354,12 @@
 	priv->input_dev->name = "Dell Privacy Driver";
 	priv->input_dev->id.bustype = BUS_HOST;
 
-	ret = input_register_device(priv->input_dev);
-	if (ret)
-		return ret;
+	/* Report initial camera-cover status */
+	if (priv->features_present & BIT(DELL_PRIVACY_TYPE_CAMERA))
+		input_report_switch(priv->input_dev, SW_CAMERA_LENS_COVER,
+				    !(priv->last_status & CAMERA_STATUS));
 
-	ret = get_current_status(priv->wdev);
+	ret = input_register_device(priv->input_dev);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/dell/dell-wmi-sysman/sysman.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/dell/dell-wmi-sysman/sysman.c
@@ -396,6 +396,7 @@
 	struct kobject *attr_name_kobj; //individual attribute names
 	union acpi_object *obj = NULL;
 	union acpi_object *elements;
+	struct kobject *duplicate;
 	struct kset *tmp_set;
 	int min_elements;
 
@@ -454,9 +455,11 @@
 		else
 			tmp_set = wmi_priv.main_dir_kset;
 
-		if (kset_find_obj(tmp_set, elements[ATTR_NAME].string.pointer)) {
-			pr_debug("duplicate attribute name found - %s\n",
-				elements[ATTR_NAME].string.pointer);
+		duplicate = kset_find_obj(tmp_set, elements[ATTR_NAME].string.pointer);
+		if (duplicate) {
+			pr_debug("Duplicate attribute name found - %s\n",
+				 elements[ATTR_NAME].string.pointer);
+			kobject_put(duplicate);
 			goto nextobj;
 		}
 
@@ -521,6 +524,7 @@
 	int ret = 0;
 
 	if (!dmi_find_device(DMI_DEV_TYPE_OEM_STRING, "Dell System", NULL) &&
+	    !dmi_find_device(DMI_DEV_TYPE_OEM_STRING, "Alienware", NULL) &&
 	    !dmi_find_device(DMI_DEV_TYPE_OEM_STRING, "www.dell.com", NULL)) {
 		pr_err("Unable to run on non-Dell system\n");
 		return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/gigabyte-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/gigabyte-wmi.c
@@ -140,6 +140,9 @@
 	}}
 
 static const struct dmi_system_id gigabyte_wmi_known_working_platforms[] = {
+	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("A320M-S2H V2-CF"),
+	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("B450M DS3H-CF"),
+	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("B450M DS3H WIFI-CF"),
 	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("B450M S2H V2"),
 	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("B550 AORUS ELITE AX V2"),
 	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("B550 AORUS ELITE"),
@@ -153,6 +156,8 @@
 	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("X570 GAMING X"),
 	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("X570 I AORUS PRO WIFI"),
 	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("X570 UD"),
+	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("X570S AORUS ELITE"),
+	DMI_EXACT_MATCH_GIGABYTE_BOARD_NAME("Z690M AORUS ELITE AX DDR4"),
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/hp/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/hp/Kconfig
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# X86 Platform Specific Drivers
+#
+menuconfig X86_PLATFORM_DRIVERS_HP
+	bool "HP X86 Platform Specific Device Drivers"
+	depends on X86_PLATFORM_DEVICES
+	help
+	  Say Y here to get to see options for device drivers for various
+	  HP x86 platforms, including vendor-specific laptop extension drivers.
+	  This option alone does not add any kernel code.
+
+	  If you say N, all options in this submenu will be skipped and disabled.
+
+if X86_PLATFORM_DRIVERS_HP
+
+config HP_ACCEL
+	tristate "HP laptop accelerometer"
+	default m
+	depends on INPUT && ACPI
+	depends on SERIO_I8042
+	select SENSORS_LIS3LV02D
+	select NEW_LEDS
+	select LEDS_CLASS
+	help
+	  This driver provides support for the "Mobile Data Protection System 3D"
+	  or "3D DriveGuard" feature of HP laptops. On such systems the driver
+	  should load automatically (via ACPI alias).
+
+	  Support for a led indicating disk protection will be provided as
+	  hp::hddprotect. For more information on the feature, refer to
+	  Documentation/misc-devices/lis3lv02d.rst.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called hp_accel.
+
+config HP_WMI
+	tristate "HP WMI extras"
+	default m
+	depends on ACPI_WMI
+	depends on INPUT
+	depends on RFKILL || RFKILL = n
+	select INPUT_SPARSEKMAP
+	select ACPI_PLATFORM_PROFILE
+	select HWMON
+	help
+	  Say Y here if you want to support WMI-based hotkeys on HP laptops and
+	  to read data from WMI such as docking or ambient light sensor state.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called hp-wmi.
+
+config TC1100_WMI
+	tristate "HP Compaq TC1100 Tablet WMI Extras"
+	default m
+	depends on !X86_64
+	depends on ACPI
+	depends on ACPI_WMI
+	help
+	  This is a driver for the WMI extensions (wireless and bluetooth power
+	  control) of the HP Compaq TC1100 tablet.
+
+endif # X86_PLATFORM_DRIVERS_HP
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/hp/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/hp/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for linux/drivers/platform/x86/hp
+# HP x86 Platform-Specific Drivers
+#
+
+# Hewlett Packard
+obj-$(CONFIG_HP_ACCEL)		+= hp_accel.o
+obj-$(CONFIG_HP_WMI)		+= hp-wmi.o
+obj-$(CONFIG_TC1100_WMI)	+= tc1100-wmi.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/hp/hp-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/hp/hp-wmi.c
@@ -0,0 +1,1144 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * HP WMI hotkeys
+ *
+ * Copyright (C) 2008 Red Hat <mjg@redhat.com>
+ * Copyright (C) 2010, 2011 Anssi Hannula <anssi.hannula@iki.fi>
+ *
+ * Portions based on wistron_btns.c:
+ * Copyright (C) 2005 Miloslav Trmac <mitr@volny.cz>
+ * Copyright (C) 2005 Bernhard Rosenkraenzer <bero@arklinux.org>
+ * Copyright (C) 2005 Dmitry Torokhov <dtor@mail.ru>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/input.h>
+#include <linux/input/sparse-keymap.h>
+#include <linux/platform_device.h>
+#include <linux/platform_profile.h>
+#include <linux/acpi.h>
+#include <linux/rfkill.h>
+#include <linux/string.h>
+
+MODULE_AUTHOR("Matthew Garrett <mjg59@srcf.ucam.org>");
+MODULE_DESCRIPTION("HP laptop WMI hotkeys driver");
+MODULE_LICENSE("GPL");
+
+MODULE_ALIAS("wmi:95F24279-4D7B-4334-9387-ACCDC67EF61C");
+MODULE_ALIAS("wmi:5FB7F034-2C63-45e9-BE91-3D44E2C707E4");
+
+static int enable_tablet_mode_sw = -1;
+module_param(enable_tablet_mode_sw, int, 0444);
+MODULE_PARM_DESC(enable_tablet_mode_sw, "Enable SW_TABLET_MODE reporting (-1=auto, 0=no, 1=yes)");
+
+#define HPWMI_EVENT_GUID "95F24279-4D7B-4334-9387-ACCDC67EF61C"
+#define HPWMI_BIOS_GUID "5FB7F034-2C63-45e9-BE91-3D44E2C707E4"
+
+enum hp_wmi_radio {
+	HPWMI_WIFI	= 0x0,
+	HPWMI_BLUETOOTH	= 0x1,
+	HPWMI_WWAN	= 0x2,
+	HPWMI_GPS	= 0x3,
+};
+
+enum hp_wmi_event_ids {
+	HPWMI_DOCK_EVENT		= 0x01,
+	HPWMI_PARK_HDD			= 0x02,
+	HPWMI_SMART_ADAPTER		= 0x03,
+	HPWMI_BEZEL_BUTTON		= 0x04,
+	HPWMI_WIRELESS			= 0x05,
+	HPWMI_CPU_BATTERY_THROTTLE	= 0x06,
+	HPWMI_LOCK_SWITCH		= 0x07,
+	HPWMI_LID_SWITCH		= 0x08,
+	HPWMI_SCREEN_ROTATION		= 0x09,
+	HPWMI_COOLSENSE_SYSTEM_MOBILE	= 0x0A,
+	HPWMI_COOLSENSE_SYSTEM_HOT	= 0x0B,
+	HPWMI_PROXIMITY_SENSOR		= 0x0C,
+	HPWMI_BACKLIT_KB_BRIGHTNESS	= 0x0D,
+	HPWMI_PEAKSHIFT_PERIOD		= 0x0F,
+	HPWMI_BATTERY_CHARGE_PERIOD	= 0x10,
+	HPWMI_SANITIZATION_MODE		= 0x17,
+	HPWMI_SMART_EXPERIENCE_APP	= 0x21,
+};
+
+struct bios_args {
+	u32 signature;
+	u32 command;
+	u32 commandtype;
+	u32 datasize;
+	u8 data[128];
+};
+
+enum hp_wmi_commandtype {
+	HPWMI_DISPLAY_QUERY		= 0x01,
+	HPWMI_HDDTEMP_QUERY		= 0x02,
+	HPWMI_ALS_QUERY			= 0x03,
+	HPWMI_HARDWARE_QUERY		= 0x04,
+	HPWMI_WIRELESS_QUERY		= 0x05,
+	HPWMI_BATTERY_QUERY		= 0x07,
+	HPWMI_BIOS_QUERY		= 0x09,
+	HPWMI_FEATURE_QUERY		= 0x0b,
+	HPWMI_HOTKEY_QUERY		= 0x0c,
+	HPWMI_FEATURE2_QUERY		= 0x0d,
+	HPWMI_WIRELESS2_QUERY		= 0x1b,
+	HPWMI_POSTCODEERROR_QUERY	= 0x2a,
+	HPWMI_THERMAL_PROFILE_QUERY	= 0x4c,
+};
+
+enum hp_wmi_command {
+	HPWMI_READ	= 0x01,
+	HPWMI_WRITE	= 0x02,
+	HPWMI_ODM	= 0x03,
+};
+
+enum hp_wmi_hardware_mask {
+	HPWMI_DOCK_MASK		= 0x01,
+	HPWMI_TABLET_MASK	= 0x04,
+};
+
+struct bios_return {
+	u32 sigpass;
+	u32 return_code;
+};
+
+enum hp_return_value {
+	HPWMI_RET_WRONG_SIGNATURE	= 0x02,
+	HPWMI_RET_UNKNOWN_COMMAND	= 0x03,
+	HPWMI_RET_UNKNOWN_CMDTYPE	= 0x04,
+	HPWMI_RET_INVALID_PARAMETERS	= 0x05,
+};
+
+enum hp_wireless2_bits {
+	HPWMI_POWER_STATE	= 0x01,
+	HPWMI_POWER_SOFT	= 0x02,
+	HPWMI_POWER_BIOS	= 0x04,
+	HPWMI_POWER_HARD	= 0x08,
+	HPWMI_POWER_FW_OR_HW	= HPWMI_POWER_BIOS | HPWMI_POWER_HARD,
+};
+
+enum hp_thermal_profile {
+	HP_THERMAL_PROFILE_PERFORMANCE	= 0x00,
+	HP_THERMAL_PROFILE_DEFAULT		= 0x01,
+	HP_THERMAL_PROFILE_COOL			= 0x02
+};
+
+#define IS_HWBLOCKED(x) ((x & HPWMI_POWER_FW_OR_HW) != HPWMI_POWER_FW_OR_HW)
+#define IS_SWBLOCKED(x) !(x & HPWMI_POWER_SOFT)
+
+struct bios_rfkill2_device_state {
+	u8 radio_type;
+	u8 bus_type;
+	u16 vendor_id;
+	u16 product_id;
+	u16 subsys_vendor_id;
+	u16 subsys_product_id;
+	u8 rfkill_id;
+	u8 power;
+	u8 unknown[4];
+};
+
+/* 7 devices fit into the 128 byte buffer */
+#define HPWMI_MAX_RFKILL2_DEVICES	7
+
+struct bios_rfkill2_state {
+	u8 unknown[7];
+	u8 count;
+	u8 pad[8];
+	struct bios_rfkill2_device_state device[HPWMI_MAX_RFKILL2_DEVICES];
+};
+
+static const struct key_entry hp_wmi_keymap[] = {
+	{ KE_KEY, 0x02,    { KEY_BRIGHTNESSUP } },
+	{ KE_KEY, 0x03,    { KEY_BRIGHTNESSDOWN } },
+	{ KE_KEY, 0x270,   { KEY_MICMUTE } },
+	{ KE_KEY, 0x20e6,  { KEY_PROG1 } },
+	{ KE_KEY, 0x20e8,  { KEY_MEDIA } },
+	{ KE_KEY, 0x2142,  { KEY_MEDIA } },
+	{ KE_KEY, 0x213b,  { KEY_INFO } },
+	{ KE_KEY, 0x2169,  { KEY_ROTATE_DISPLAY } },
+	{ KE_KEY, 0x216a,  { KEY_SETUP } },
+	{ KE_KEY, 0x21a9,  { KEY_TOUCHPAD_OFF } },
+	{ KE_KEY, 0x121a9, { KEY_TOUCHPAD_ON } },
+	{ KE_KEY, 0x231b,  { KEY_HELP } },
+	{ KE_END, 0 }
+};
+
+static struct input_dev *hp_wmi_input_dev;
+static struct platform_device *hp_wmi_platform_dev;
+static struct platform_profile_handler platform_profile_handler;
+static bool platform_profile_support;
+
+static struct rfkill *wifi_rfkill;
+static struct rfkill *bluetooth_rfkill;
+static struct rfkill *wwan_rfkill;
+
+struct rfkill2_device {
+	u8 id;
+	int num;
+	struct rfkill *rfkill;
+};
+
+static int rfkill2_count;
+static struct rfkill2_device rfkill2[HPWMI_MAX_RFKILL2_DEVICES];
+
+/* map output size to the corresponding WMI method id */
+static inline int encode_outsize_for_pvsz(int outsize)
+{
+	if (outsize > 4096)
+		return -EINVAL;
+	if (outsize > 1024)
+		return 5;
+	if (outsize > 128)
+		return 4;
+	if (outsize > 4)
+		return 3;
+	if (outsize > 0)
+		return 2;
+	return 1;
+}
+
+/*
+ * hp_wmi_perform_query
+ *
+ * query:	The commandtype (enum hp_wmi_commandtype)
+ * write:	The command (enum hp_wmi_command)
+ * buffer:	Buffer used as input and/or output
+ * insize:	Size of input buffer
+ * outsize:	Size of output buffer
+ *
+ * returns zero on success
+ *         an HP WMI query specific error code (which is positive)
+ *         -EINVAL if the query was not successful at all
+ *         -EINVAL if the output buffer size exceeds buffersize
+ *
+ * Note: The buffersize must at least be the maximum of the input and output
+ *       size. E.g. Battery info query is defined to have 1 byte input
+ *       and 128 byte output. The caller would do:
+ *       buffer = kzalloc(128, GFP_KERNEL);
+ *       ret = hp_wmi_perform_query(HPWMI_BATTERY_QUERY, HPWMI_READ, buffer, 1, 128)
+ */
+static int hp_wmi_perform_query(int query, enum hp_wmi_command command,
+				void *buffer, int insize, int outsize)
+{
+	int mid;
+	struct bios_return *bios_return;
+	int actual_outsize;
+	union acpi_object *obj;
+	struct bios_args args = {
+		.signature = 0x55434553,
+		.command = command,
+		.commandtype = query,
+		.datasize = insize,
+		.data = { 0 },
+	};
+	struct acpi_buffer input = { sizeof(struct bios_args), &args };
+	struct acpi_buffer output = { ACPI_ALLOCATE_BUFFER, NULL };
+	int ret = 0;
+
+	mid = encode_outsize_for_pvsz(outsize);
+	if (WARN_ON(mid < 0))
+		return mid;
+
+	if (WARN_ON(insize > sizeof(args.data)))
+		return -EINVAL;
+	memcpy(&args.data[0], buffer, insize);
+
+	wmi_evaluate_method(HPWMI_BIOS_GUID, 0, mid, &input, &output);
+
+	obj = output.pointer;
+
+	if (!obj)
+		return -EINVAL;
+
+	if (obj->type != ACPI_TYPE_BUFFER) {
+		ret = -EINVAL;
+		goto out_free;
+	}
+
+	bios_return = (struct bios_return *)obj->buffer.pointer;
+	ret = bios_return->return_code;
+
+	if (ret) {
+		if (ret != HPWMI_RET_UNKNOWN_COMMAND &&
+		    ret != HPWMI_RET_UNKNOWN_CMDTYPE)
+			pr_warn("query 0x%x returned error 0x%x\n", query, ret);
+		goto out_free;
+	}
+
+	/* Ignore output data of zero size */
+	if (!outsize)
+		goto out_free;
+
+	actual_outsize = min(outsize, (int)(obj->buffer.length - sizeof(*bios_return)));
+	memcpy(buffer, obj->buffer.pointer + sizeof(*bios_return), actual_outsize);
+	memset(buffer + actual_outsize, 0, outsize - actual_outsize);
+
+out_free:
+	kfree(obj);
+	return ret;
+}
+
+static int hp_wmi_read_int(int query)
+{
+	int val = 0, ret;
+
+	ret = hp_wmi_perform_query(query, HPWMI_READ, &val,
+				   0, sizeof(val));
+
+	if (ret)
+		return ret < 0 ? ret : -EINVAL;
+
+	return val;
+}
+
+static int hp_wmi_hw_state(int mask)
+{
+	int state = hp_wmi_read_int(HPWMI_HARDWARE_QUERY);
+
+	if (state < 0)
+		return state;
+
+	return !!(state & mask);
+}
+
+static int __init hp_wmi_bios_2008_later(void)
+{
+	int state = 0;
+	int ret = hp_wmi_perform_query(HPWMI_FEATURE_QUERY, HPWMI_READ, &state,
+				       sizeof(state), sizeof(state));
+	if (!ret)
+		return 1;
+
+	return (ret == HPWMI_RET_UNKNOWN_CMDTYPE) ? 0 : -ENXIO;
+}
+
+static int __init hp_wmi_bios_2009_later(void)
+{
+	u8 state[128];
+	int ret = hp_wmi_perform_query(HPWMI_FEATURE2_QUERY, HPWMI_READ, &state,
+				       sizeof(state), sizeof(state));
+	if (!ret)
+		return 1;
+
+	return (ret == HPWMI_RET_UNKNOWN_CMDTYPE) ? 0 : -ENXIO;
+}
+
+static int __init hp_wmi_enable_hotkeys(void)
+{
+	int value = 0x6e;
+	int ret = hp_wmi_perform_query(HPWMI_BIOS_QUERY, HPWMI_WRITE, &value,
+				       sizeof(value), 0);
+
+	return ret <= 0 ? ret : -EINVAL;
+}
+
+static int hp_wmi_set_block(void *data, bool blocked)
+{
+	enum hp_wmi_radio r = (enum hp_wmi_radio) data;
+	int query = BIT(r + 8) | ((!blocked) << r);
+	int ret;
+
+	ret = hp_wmi_perform_query(HPWMI_WIRELESS_QUERY, HPWMI_WRITE,
+				   &query, sizeof(query), 0);
+
+	return ret <= 0 ? ret : -EINVAL;
+}
+
+static const struct rfkill_ops hp_wmi_rfkill_ops = {
+	.set_block = hp_wmi_set_block,
+};
+
+static bool hp_wmi_get_sw_state(enum hp_wmi_radio r)
+{
+	int mask = 0x200 << (r * 8);
+
+	int wireless = hp_wmi_read_int(HPWMI_WIRELESS_QUERY);
+
+	/* TBD: Pass error */
+	WARN_ONCE(wireless < 0, "error executing HPWMI_WIRELESS_QUERY");
+
+	return !(wireless & mask);
+}
+
+static bool hp_wmi_get_hw_state(enum hp_wmi_radio r)
+{
+	int mask = 0x800 << (r * 8);
+
+	int wireless = hp_wmi_read_int(HPWMI_WIRELESS_QUERY);
+
+	/* TBD: Pass error */
+	WARN_ONCE(wireless < 0, "error executing HPWMI_WIRELESS_QUERY");
+
+	return !(wireless & mask);
+}
+
+static int hp_wmi_rfkill2_set_block(void *data, bool blocked)
+{
+	int rfkill_id = (int)(long)data;
+	char buffer[4] = { 0x01, 0x00, rfkill_id, !blocked };
+	int ret;
+
+	ret = hp_wmi_perform_query(HPWMI_WIRELESS2_QUERY, HPWMI_WRITE,
+				   buffer, sizeof(buffer), 0);
+
+	return ret <= 0 ? ret : -EINVAL;
+}
+
+static const struct rfkill_ops hp_wmi_rfkill2_ops = {
+	.set_block = hp_wmi_rfkill2_set_block,
+};
+
+static int hp_wmi_rfkill2_refresh(void)
+{
+	struct bios_rfkill2_state state;
+	int err, i;
+
+	err = hp_wmi_perform_query(HPWMI_WIRELESS2_QUERY, HPWMI_READ, &state,
+				   sizeof(state), sizeof(state));
+	if (err)
+		return err;
+
+	for (i = 0; i < rfkill2_count; i++) {
+		int num = rfkill2[i].num;
+		struct bios_rfkill2_device_state *devstate;
+		devstate = &state.device[num];
+
+		if (num >= state.count ||
+		    devstate->rfkill_id != rfkill2[i].id) {
+			pr_warn("power configuration of the wireless devices unexpectedly changed\n");
+			continue;
+		}
+
+		rfkill_set_states(rfkill2[i].rfkill,
+				  IS_SWBLOCKED(devstate->power),
+				  IS_HWBLOCKED(devstate->power));
+	}
+
+	return 0;
+}
+
+static ssize_t display_show(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	int value = hp_wmi_read_int(HPWMI_DISPLAY_QUERY);
+	if (value < 0)
+		return value;
+	return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t hddtemp_show(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	int value = hp_wmi_read_int(HPWMI_HDDTEMP_QUERY);
+	if (value < 0)
+		return value;
+	return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t als_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	int value = hp_wmi_read_int(HPWMI_ALS_QUERY);
+	if (value < 0)
+		return value;
+	return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t dock_show(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	int value = hp_wmi_hw_state(HPWMI_DOCK_MASK);
+	if (value < 0)
+		return value;
+	return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t tablet_show(struct device *dev, struct device_attribute *attr,
+			   char *buf)
+{
+	int value = hp_wmi_hw_state(HPWMI_TABLET_MASK);
+	if (value < 0)
+		return value;
+	return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t postcode_show(struct device *dev, struct device_attribute *attr,
+			     char *buf)
+{
+	/* Get the POST error code of previous boot failure. */
+	int value = hp_wmi_read_int(HPWMI_POSTCODEERROR_QUERY);
+	if (value < 0)
+		return value;
+	return sprintf(buf, "0x%x\n", value);
+}
+
+static ssize_t als_store(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	u32 tmp;
+	int ret;
+
+	ret = kstrtou32(buf, 10, &tmp);
+	if (ret)
+		return ret;
+
+	ret = hp_wmi_perform_query(HPWMI_ALS_QUERY, HPWMI_WRITE, &tmp,
+				       sizeof(tmp), sizeof(tmp));
+	if (ret)
+		return ret < 0 ? ret : -EINVAL;
+
+	return count;
+}
+
+static ssize_t postcode_store(struct device *dev, struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	u32 tmp = 1;
+	bool clear;
+	int ret;
+
+	ret = kstrtobool(buf, &clear);
+	if (ret)
+		return ret;
+
+	if (clear == false)
+		return -EINVAL;
+
+	/* Clear the POST error code. It is kept until until cleared. */
+	ret = hp_wmi_perform_query(HPWMI_POSTCODEERROR_QUERY, HPWMI_WRITE, &tmp,
+				       sizeof(tmp), sizeof(tmp));
+	if (ret)
+		return ret < 0 ? ret : -EINVAL;
+
+	return count;
+}
+
+static DEVICE_ATTR_RO(display);
+static DEVICE_ATTR_RO(hddtemp);
+static DEVICE_ATTR_RW(als);
+static DEVICE_ATTR_RO(dock);
+static DEVICE_ATTR_RO(tablet);
+static DEVICE_ATTR_RW(postcode);
+
+static struct attribute *hp_wmi_attrs[] = {
+	&dev_attr_display.attr,
+	&dev_attr_hddtemp.attr,
+	&dev_attr_als.attr,
+	&dev_attr_dock.attr,
+	&dev_attr_tablet.attr,
+	&dev_attr_postcode.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(hp_wmi);
+
+static void hp_wmi_notify(u32 value, void *context)
+{
+	struct acpi_buffer response = { ACPI_ALLOCATE_BUFFER, NULL };
+	u32 event_id, event_data;
+	union acpi_object *obj;
+	acpi_status status;
+	u32 *location;
+	int key_code;
+
+	status = wmi_get_event_data(value, &response);
+	if (status != AE_OK) {
+		pr_info("bad event status 0x%x\n", status);
+		return;
+	}
+
+	obj = (union acpi_object *)response.pointer;
+
+	if (!obj)
+		return;
+	if (obj->type != ACPI_TYPE_BUFFER) {
+		pr_info("Unknown response received %d\n", obj->type);
+		kfree(obj);
+		return;
+	}
+
+	/*
+	 * Depending on ACPI version the concatenation of id and event data
+	 * inside _WED function will result in a 8 or 16 byte buffer.
+	 */
+	location = (u32 *)obj->buffer.pointer;
+	if (obj->buffer.length == 8) {
+		event_id = *location;
+		event_data = *(location + 1);
+	} else if (obj->buffer.length == 16) {
+		event_id = *location;
+		event_data = *(location + 2);
+	} else {
+		pr_info("Unknown buffer length %d\n", obj->buffer.length);
+		kfree(obj);
+		return;
+	}
+	kfree(obj);
+
+	switch (event_id) {
+	case HPWMI_DOCK_EVENT:
+		if (test_bit(SW_DOCK, hp_wmi_input_dev->swbit))
+			input_report_switch(hp_wmi_input_dev, SW_DOCK,
+					    hp_wmi_hw_state(HPWMI_DOCK_MASK));
+		if (test_bit(SW_TABLET_MODE, hp_wmi_input_dev->swbit))
+			input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE,
+					    hp_wmi_hw_state(HPWMI_TABLET_MASK));
+		input_sync(hp_wmi_input_dev);
+		break;
+	case HPWMI_PARK_HDD:
+		break;
+	case HPWMI_SMART_ADAPTER:
+		break;
+	case HPWMI_BEZEL_BUTTON:
+		key_code = hp_wmi_read_int(HPWMI_HOTKEY_QUERY);
+		if (key_code < 0)
+			break;
+
+		if (!sparse_keymap_report_event(hp_wmi_input_dev,
+						key_code, 1, true))
+			pr_info("Unknown key code - 0x%x\n", key_code);
+		break;
+	case HPWMI_WIRELESS:
+		if (rfkill2_count) {
+			hp_wmi_rfkill2_refresh();
+			break;
+		}
+
+		if (wifi_rfkill)
+			rfkill_set_states(wifi_rfkill,
+					  hp_wmi_get_sw_state(HPWMI_WIFI),
+					  hp_wmi_get_hw_state(HPWMI_WIFI));
+		if (bluetooth_rfkill)
+			rfkill_set_states(bluetooth_rfkill,
+					  hp_wmi_get_sw_state(HPWMI_BLUETOOTH),
+					  hp_wmi_get_hw_state(HPWMI_BLUETOOTH));
+		if (wwan_rfkill)
+			rfkill_set_states(wwan_rfkill,
+					  hp_wmi_get_sw_state(HPWMI_WWAN),
+					  hp_wmi_get_hw_state(HPWMI_WWAN));
+		break;
+	case HPWMI_CPU_BATTERY_THROTTLE:
+		pr_info("Unimplemented CPU throttle because of 3 Cell battery event detected\n");
+		break;
+	case HPWMI_LOCK_SWITCH:
+		break;
+	case HPWMI_LID_SWITCH:
+		break;
+	case HPWMI_SCREEN_ROTATION:
+		break;
+	case HPWMI_COOLSENSE_SYSTEM_MOBILE:
+		break;
+	case HPWMI_COOLSENSE_SYSTEM_HOT:
+		break;
+	case HPWMI_PROXIMITY_SENSOR:
+		break;
+	case HPWMI_BACKLIT_KB_BRIGHTNESS:
+		break;
+	case HPWMI_PEAKSHIFT_PERIOD:
+		break;
+	case HPWMI_BATTERY_CHARGE_PERIOD:
+		break;
+	case HPWMI_SANITIZATION_MODE:
+		break;
+	case HPWMI_SMART_EXPERIENCE_APP:
+		break;
+	default:
+		pr_info("Unknown event_id - %d - 0x%x\n", event_id, event_data);
+		break;
+	}
+}
+
+static int __init hp_wmi_input_setup(void)
+{
+	acpi_status status;
+	int err, val;
+
+	hp_wmi_input_dev = input_allocate_device();
+	if (!hp_wmi_input_dev)
+		return -ENOMEM;
+
+	hp_wmi_input_dev->name = "HP WMI hotkeys";
+	hp_wmi_input_dev->phys = "wmi/input0";
+	hp_wmi_input_dev->id.bustype = BUS_HOST;
+
+	__set_bit(EV_SW, hp_wmi_input_dev->evbit);
+
+	/* Dock */
+	val = hp_wmi_hw_state(HPWMI_DOCK_MASK);
+	if (!(val < 0)) {
+		__set_bit(SW_DOCK, hp_wmi_input_dev->swbit);
+		input_report_switch(hp_wmi_input_dev, SW_DOCK, val);
+	}
+
+	/* Tablet mode */
+	if (enable_tablet_mode_sw > 0) {
+		val = hp_wmi_hw_state(HPWMI_TABLET_MASK);
+		if (val >= 0) {
+			__set_bit(SW_TABLET_MODE, hp_wmi_input_dev->swbit);
+			input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE, val);
+		}
+	}
+
+	err = sparse_keymap_setup(hp_wmi_input_dev, hp_wmi_keymap, NULL);
+	if (err)
+		goto err_free_dev;
+
+	/* Set initial hardware state */
+	input_sync(hp_wmi_input_dev);
+
+	if (!hp_wmi_bios_2009_later() && hp_wmi_bios_2008_later())
+		hp_wmi_enable_hotkeys();
+
+	status = wmi_install_notify_handler(HPWMI_EVENT_GUID, hp_wmi_notify, NULL);
+	if (ACPI_FAILURE(status)) {
+		err = -EIO;
+		goto err_free_dev;
+	}
+
+	err = input_register_device(hp_wmi_input_dev);
+	if (err)
+		goto err_uninstall_notifier;
+
+	return 0;
+
+ err_uninstall_notifier:
+	wmi_remove_notify_handler(HPWMI_EVENT_GUID);
+ err_free_dev:
+	input_free_device(hp_wmi_input_dev);
+	return err;
+}
+
+static void hp_wmi_input_destroy(void)
+{
+	wmi_remove_notify_handler(HPWMI_EVENT_GUID);
+	input_unregister_device(hp_wmi_input_dev);
+}
+
+static int __init hp_wmi_rfkill_setup(struct platform_device *device)
+{
+	int err, wireless;
+
+	wireless = hp_wmi_read_int(HPWMI_WIRELESS_QUERY);
+	if (wireless < 0)
+		return wireless;
+
+	err = hp_wmi_perform_query(HPWMI_WIRELESS_QUERY, HPWMI_WRITE, &wireless,
+				   sizeof(wireless), 0);
+	if (err)
+		return err;
+
+	if (wireless & 0x1) {
+		wifi_rfkill = rfkill_alloc("hp-wifi", &device->dev,
+					   RFKILL_TYPE_WLAN,
+					   &hp_wmi_rfkill_ops,
+					   (void *) HPWMI_WIFI);
+		if (!wifi_rfkill)
+			return -ENOMEM;
+		rfkill_init_sw_state(wifi_rfkill,
+				     hp_wmi_get_sw_state(HPWMI_WIFI));
+		rfkill_set_hw_state(wifi_rfkill,
+				    hp_wmi_get_hw_state(HPWMI_WIFI));
+		err = rfkill_register(wifi_rfkill);
+		if (err)
+			goto register_wifi_error;
+	}
+
+	if (wireless & 0x2) {
+		bluetooth_rfkill = rfkill_alloc("hp-bluetooth", &device->dev,
+						RFKILL_TYPE_BLUETOOTH,
+						&hp_wmi_rfkill_ops,
+						(void *) HPWMI_BLUETOOTH);
+		if (!bluetooth_rfkill) {
+			err = -ENOMEM;
+			goto register_bluetooth_error;
+		}
+		rfkill_init_sw_state(bluetooth_rfkill,
+				     hp_wmi_get_sw_state(HPWMI_BLUETOOTH));
+		rfkill_set_hw_state(bluetooth_rfkill,
+				    hp_wmi_get_hw_state(HPWMI_BLUETOOTH));
+		err = rfkill_register(bluetooth_rfkill);
+		if (err)
+			goto register_bluetooth_error;
+	}
+
+	if (wireless & 0x4) {
+		wwan_rfkill = rfkill_alloc("hp-wwan", &device->dev,
+					   RFKILL_TYPE_WWAN,
+					   &hp_wmi_rfkill_ops,
+					   (void *) HPWMI_WWAN);
+		if (!wwan_rfkill) {
+			err = -ENOMEM;
+			goto register_wwan_error;
+		}
+		rfkill_init_sw_state(wwan_rfkill,
+				     hp_wmi_get_sw_state(HPWMI_WWAN));
+		rfkill_set_hw_state(wwan_rfkill,
+				    hp_wmi_get_hw_state(HPWMI_WWAN));
+		err = rfkill_register(wwan_rfkill);
+		if (err)
+			goto register_wwan_error;
+	}
+
+	return 0;
+
+register_wwan_error:
+	rfkill_destroy(wwan_rfkill);
+	wwan_rfkill = NULL;
+	if (bluetooth_rfkill)
+		rfkill_unregister(bluetooth_rfkill);
+register_bluetooth_error:
+	rfkill_destroy(bluetooth_rfkill);
+	bluetooth_rfkill = NULL;
+	if (wifi_rfkill)
+		rfkill_unregister(wifi_rfkill);
+register_wifi_error:
+	rfkill_destroy(wifi_rfkill);
+	wifi_rfkill = NULL;
+	return err;
+}
+
+static int __init hp_wmi_rfkill2_setup(struct platform_device *device)
+{
+	struct bios_rfkill2_state state;
+	int err, i;
+
+	err = hp_wmi_perform_query(HPWMI_WIRELESS2_QUERY, HPWMI_READ, &state,
+				   sizeof(state), sizeof(state));
+	if (err)
+		return err < 0 ? err : -EINVAL;
+
+	if (state.count > HPWMI_MAX_RFKILL2_DEVICES) {
+		pr_warn("unable to parse 0x1b query output\n");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < state.count; i++) {
+		struct rfkill *rfkill;
+		enum rfkill_type type;
+		char *name;
+		switch (state.device[i].radio_type) {
+		case HPWMI_WIFI:
+			type = RFKILL_TYPE_WLAN;
+			name = "hp-wifi";
+			break;
+		case HPWMI_BLUETOOTH:
+			type = RFKILL_TYPE_BLUETOOTH;
+			name = "hp-bluetooth";
+			break;
+		case HPWMI_WWAN:
+			type = RFKILL_TYPE_WWAN;
+			name = "hp-wwan";
+			break;
+		case HPWMI_GPS:
+			type = RFKILL_TYPE_GPS;
+			name = "hp-gps";
+			break;
+		default:
+			pr_warn("unknown device type 0x%x\n",
+				state.device[i].radio_type);
+			continue;
+		}
+
+		if (!state.device[i].vendor_id) {
+			pr_warn("zero device %d while %d reported\n",
+				i, state.count);
+			continue;
+		}
+
+		rfkill = rfkill_alloc(name, &device->dev, type,
+				      &hp_wmi_rfkill2_ops, (void *)(long)i);
+		if (!rfkill) {
+			err = -ENOMEM;
+			goto fail;
+		}
+
+		rfkill2[rfkill2_count].id = state.device[i].rfkill_id;
+		rfkill2[rfkill2_count].num = i;
+		rfkill2[rfkill2_count].rfkill = rfkill;
+
+		rfkill_init_sw_state(rfkill,
+				     IS_SWBLOCKED(state.device[i].power));
+		rfkill_set_hw_state(rfkill,
+				    IS_HWBLOCKED(state.device[i].power));
+
+		if (!(state.device[i].power & HPWMI_POWER_BIOS))
+			pr_info("device %s blocked by BIOS\n", name);
+
+		err = rfkill_register(rfkill);
+		if (err) {
+			rfkill_destroy(rfkill);
+			goto fail;
+		}
+
+		rfkill2_count++;
+	}
+
+	return 0;
+fail:
+	for (; rfkill2_count > 0; rfkill2_count--) {
+		rfkill_unregister(rfkill2[rfkill2_count - 1].rfkill);
+		rfkill_destroy(rfkill2[rfkill2_count - 1].rfkill);
+	}
+	return err;
+}
+
+static int thermal_profile_get(void)
+{
+	return hp_wmi_read_int(HPWMI_THERMAL_PROFILE_QUERY);
+}
+
+static int thermal_profile_set(int thermal_profile)
+{
+	return hp_wmi_perform_query(HPWMI_THERMAL_PROFILE_QUERY, HPWMI_WRITE, &thermal_profile,
+							   sizeof(thermal_profile), 0);
+}
+
+static int platform_profile_get(struct platform_profile_handler *pprof,
+				enum platform_profile_option *profile)
+{
+	int tp;
+
+	tp = thermal_profile_get();
+	if (tp < 0)
+		return tp;
+
+	switch (tp) {
+	case HP_THERMAL_PROFILE_PERFORMANCE:
+		*profile =  PLATFORM_PROFILE_PERFORMANCE;
+		break;
+	case HP_THERMAL_PROFILE_DEFAULT:
+		*profile =  PLATFORM_PROFILE_BALANCED;
+		break;
+	case HP_THERMAL_PROFILE_COOL:
+		*profile =  PLATFORM_PROFILE_COOL;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int platform_profile_set(struct platform_profile_handler *pprof,
+				enum platform_profile_option profile)
+{
+	int err, tp;
+
+	switch (profile) {
+	case PLATFORM_PROFILE_PERFORMANCE:
+		tp =  HP_THERMAL_PROFILE_PERFORMANCE;
+		break;
+	case PLATFORM_PROFILE_BALANCED:
+		tp =  HP_THERMAL_PROFILE_DEFAULT;
+		break;
+	case PLATFORM_PROFILE_COOL:
+		tp =  HP_THERMAL_PROFILE_COOL;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	err = thermal_profile_set(tp);
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static int thermal_profile_setup(void)
+{
+	int err, tp;
+
+	tp = thermal_profile_get();
+	if (tp < 0)
+		return tp;
+
+	/*
+	 * call thermal profile write command to ensure that the firmware correctly
+	 * sets the OEM variables for the DPTF
+	 */
+	err = thermal_profile_set(tp);
+	if (err)
+		return err;
+
+	platform_profile_handler.profile_get = platform_profile_get,
+	platform_profile_handler.profile_set = platform_profile_set,
+
+	set_bit(PLATFORM_PROFILE_COOL, platform_profile_handler.choices);
+	set_bit(PLATFORM_PROFILE_BALANCED, platform_profile_handler.choices);
+	set_bit(PLATFORM_PROFILE_PERFORMANCE, platform_profile_handler.choices);
+
+	err = platform_profile_register(&platform_profile_handler);
+	if (err)
+		return err;
+
+	platform_profile_support = true;
+
+	return 0;
+}
+
+static int __init hp_wmi_bios_setup(struct platform_device *device)
+{
+	/* clear detected rfkill devices */
+	wifi_rfkill = NULL;
+	bluetooth_rfkill = NULL;
+	wwan_rfkill = NULL;
+	rfkill2_count = 0;
+
+	/*
+	 * In pre-2009 BIOS, command 1Bh return 0x4 to indicate that
+	 * BIOS no longer controls the power for the wireless
+	 * devices. All features supported by this command will no
+	 * longer be supported.
+	 */
+	if (!hp_wmi_bios_2009_later()) {
+		if (hp_wmi_rfkill_setup(device))
+			hp_wmi_rfkill2_setup(device);
+	}
+
+	thermal_profile_setup();
+
+	return 0;
+}
+
+static int __exit hp_wmi_bios_remove(struct platform_device *device)
+{
+	int i;
+
+	for (i = 0; i < rfkill2_count; i++) {
+		rfkill_unregister(rfkill2[i].rfkill);
+		rfkill_destroy(rfkill2[i].rfkill);
+	}
+
+	if (wifi_rfkill) {
+		rfkill_unregister(wifi_rfkill);
+		rfkill_destroy(wifi_rfkill);
+	}
+	if (bluetooth_rfkill) {
+		rfkill_unregister(bluetooth_rfkill);
+		rfkill_destroy(bluetooth_rfkill);
+	}
+	if (wwan_rfkill) {
+		rfkill_unregister(wwan_rfkill);
+		rfkill_destroy(wwan_rfkill);
+	}
+
+	if (platform_profile_support)
+		platform_profile_remove();
+
+	return 0;
+}
+
+static int hp_wmi_resume_handler(struct device *device)
+{
+	/*
+	 * Hardware state may have changed while suspended, so trigger
+	 * input events for the current state. As this is a switch,
+	 * the input layer will only actually pass it on if the state
+	 * changed.
+	 */
+	if (hp_wmi_input_dev) {
+		if (test_bit(SW_DOCK, hp_wmi_input_dev->swbit))
+			input_report_switch(hp_wmi_input_dev, SW_DOCK,
+					    hp_wmi_hw_state(HPWMI_DOCK_MASK));
+		if (test_bit(SW_TABLET_MODE, hp_wmi_input_dev->swbit))
+			input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE,
+					    hp_wmi_hw_state(HPWMI_TABLET_MASK));
+		input_sync(hp_wmi_input_dev);
+	}
+
+	if (rfkill2_count)
+		hp_wmi_rfkill2_refresh();
+
+	if (wifi_rfkill)
+		rfkill_set_states(wifi_rfkill,
+				  hp_wmi_get_sw_state(HPWMI_WIFI),
+				  hp_wmi_get_hw_state(HPWMI_WIFI));
+	if (bluetooth_rfkill)
+		rfkill_set_states(bluetooth_rfkill,
+				  hp_wmi_get_sw_state(HPWMI_BLUETOOTH),
+				  hp_wmi_get_hw_state(HPWMI_BLUETOOTH));
+	if (wwan_rfkill)
+		rfkill_set_states(wwan_rfkill,
+				  hp_wmi_get_sw_state(HPWMI_WWAN),
+				  hp_wmi_get_hw_state(HPWMI_WWAN));
+
+	return 0;
+}
+
+static const struct dev_pm_ops hp_wmi_pm_ops = {
+	.resume  = hp_wmi_resume_handler,
+	.restore  = hp_wmi_resume_handler,
+};
+
+/*
+ * hp_wmi_bios_remove() lives in .exit.text. For drivers registered via
+ * module_platform_driver_probe() this is ok because they cannot get unbound at
+ * runtime. So mark the driver struct with __refdata to prevent modpost
+ * triggering a section mismatch warning.
+ */
+static struct platform_driver hp_wmi_driver __refdata = {
+	.driver = {
+		.name = "hp-wmi",
+		.pm = &hp_wmi_pm_ops,
+		.dev_groups = hp_wmi_groups,
+	},
+	.remove = __exit_p(hp_wmi_bios_remove),
+};
+
+static int __init hp_wmi_init(void)
+{
+	int event_capable = wmi_has_guid(HPWMI_EVENT_GUID);
+	int bios_capable = wmi_has_guid(HPWMI_BIOS_GUID);
+	int err;
+
+	if (!bios_capable && !event_capable)
+		return -ENODEV;
+
+	if (event_capable) {
+		err = hp_wmi_input_setup();
+		if (err)
+			return err;
+	}
+
+	if (bios_capable) {
+		hp_wmi_platform_dev =
+			platform_device_register_simple("hp-wmi", -1, NULL, 0);
+		if (IS_ERR(hp_wmi_platform_dev)) {
+			err = PTR_ERR(hp_wmi_platform_dev);
+			goto err_destroy_input;
+		}
+
+		err = platform_driver_probe(&hp_wmi_driver, hp_wmi_bios_setup);
+		if (err)
+			goto err_unregister_device;
+	}
+
+	return 0;
+
+err_unregister_device:
+	platform_device_unregister(hp_wmi_platform_dev);
+err_destroy_input:
+	if (event_capable)
+		hp_wmi_input_destroy();
+
+	return err;
+}
+module_init(hp_wmi_init);
+
+static void __exit hp_wmi_exit(void)
+{
+	if (wmi_has_guid(HPWMI_EVENT_GUID))
+		hp_wmi_input_destroy();
+
+	if (hp_wmi_platform_dev) {
+		platform_device_unregister(hp_wmi_platform_dev);
+		platform_driver_unregister(&hp_wmi_driver);
+	}
+}
+module_exit(hp_wmi_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/hp/hp_accel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/hp/hp_accel.c
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  hp_accel.c - Interface between LIS3LV02DL driver and HP ACPI BIOS
+ *
+ *  Copyright (C) 2007-2008 Yan Burman
+ *  Copyright (C) 2008 Eric Piel
+ *  Copyright (C) 2008-2009 Pavel Machek
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/dmi.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/wait.h>
+#include <linux/poll.h>
+#include <linux/freezer.h>
+#include <linux/uaccess.h>
+#include <linux/leds.h>
+#include <linux/atomic.h>
+#include <linux/acpi.h>
+#include <linux/i8042.h>
+#include <linux/serio.h>
+#include "../../../misc/lis3lv02d/lis3lv02d.h"
+
+/* Delayed LEDs infrastructure ------------------------------------ */
+
+/* Special LED class that can defer work */
+struct delayed_led_classdev {
+	struct led_classdev led_classdev;
+	struct work_struct work;
+	enum led_brightness new_brightness;
+
+	unsigned int led;		/* For driver */
+	void (*set_brightness)(struct delayed_led_classdev *data, enum led_brightness value);
+};
+
+static inline void delayed_set_status_worker(struct work_struct *work)
+{
+	struct delayed_led_classdev *data =
+			container_of(work, struct delayed_led_classdev, work);
+
+	data->set_brightness(data, data->new_brightness);
+}
+
+static inline void delayed_sysfs_set(struct led_classdev *led_cdev,
+			      enum led_brightness brightness)
+{
+	struct delayed_led_classdev *data = container_of(led_cdev,
+			     struct delayed_led_classdev, led_classdev);
+	data->new_brightness = brightness;
+	schedule_work(&data->work);
+}
+
+/* HP-specific accelerometer driver ------------------------------------ */
+
+/* e0 25, e0 26, e0 27, e0 28 are scan codes that the accelerometer with acpi id
+ * HPQ6000 sends through the keyboard bus */
+#define ACCEL_1 0x25
+#define ACCEL_2 0x26
+#define ACCEL_3 0x27
+#define ACCEL_4 0x28
+
+/* For automatic insertion of the module */
+static const struct acpi_device_id lis3lv02d_device_ids[] = {
+	{"HPQ0004", 0}, /* HP Mobile Data Protection System PNP */
+	{"HPQ6000", 0}, /* HP Mobile Data Protection System PNP */
+	{"HPQ6007", 0}, /* HP Mobile Data Protection System PNP */
+	{"", 0},
+};
+MODULE_DEVICE_TABLE(acpi, lis3lv02d_device_ids);
+
+/**
+ * lis3lv02d_acpi_init - initialize the device for ACPI
+ * @lis3: pointer to the device struct
+ *
+ * Returns 0 on success.
+ */
+static int lis3lv02d_acpi_init(struct lis3lv02d *lis3)
+{
+	return 0;
+}
+
+/**
+ * lis3lv02d_acpi_read - ACPI ALRD method: read a register
+ * @lis3: pointer to the device struct
+ * @reg:    the register to read
+ * @ret:    result of the operation
+ *
+ * Returns 0 on success.
+ */
+static int lis3lv02d_acpi_read(struct lis3lv02d *lis3, int reg, u8 *ret)
+{
+	struct acpi_device *dev = lis3->bus_priv;
+	union acpi_object arg0 = { ACPI_TYPE_INTEGER };
+	struct acpi_object_list args = { 1, &arg0 };
+	unsigned long long lret;
+	acpi_status status;
+
+	arg0.integer.value = reg;
+
+	status = acpi_evaluate_integer(dev->handle, "ALRD", &args, &lret);
+	if (ACPI_FAILURE(status))
+		return -EINVAL;
+	*ret = lret;
+	return 0;
+}
+
+/**
+ * lis3lv02d_acpi_write - ACPI ALWR method: write to a register
+ * @lis3: pointer to the device struct
+ * @reg:    the register to write to
+ * @val:    the value to write
+ *
+ * Returns 0 on success.
+ */
+static int lis3lv02d_acpi_write(struct lis3lv02d *lis3, int reg, u8 val)
+{
+	struct acpi_device *dev = lis3->bus_priv;
+	unsigned long long ret; /* Not used when writting */
+	union acpi_object in_obj[2];
+	struct acpi_object_list args = { 2, in_obj };
+
+	in_obj[0].type          = ACPI_TYPE_INTEGER;
+	in_obj[0].integer.value = reg;
+	in_obj[1].type          = ACPI_TYPE_INTEGER;
+	in_obj[1].integer.value = val;
+
+	if (acpi_evaluate_integer(dev->handle, "ALWR", &args, &ret) != AE_OK)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int lis3lv02d_dmi_matched(const struct dmi_system_id *dmi)
+{
+	lis3_dev.ac = *((union axis_conversion *)dmi->driver_data);
+	pr_info("hardware type %s found\n", dmi->ident);
+
+	return 1;
+}
+
+/* Represents, for each axis seen by userspace, the corresponding hw axis (+1).
+ * If the value is negative, the opposite of the hw value is used. */
+#define DEFINE_CONV(name, x, y, z)			      \
+	static union axis_conversion lis3lv02d_axis_##name = \
+		{ .as_array = { x, y, z } }
+DEFINE_CONV(normal, 1, 2, 3);
+DEFINE_CONV(y_inverted, 1, -2, 3);
+DEFINE_CONV(x_inverted, -1, 2, 3);
+DEFINE_CONV(x_inverted_usd, -1, 2, -3);
+DEFINE_CONV(z_inverted, 1, 2, -3);
+DEFINE_CONV(xy_swap, 2, 1, 3);
+DEFINE_CONV(xy_rotated_left, -2, 1, 3);
+DEFINE_CONV(xy_rotated_left_usd, -2, 1, -3);
+DEFINE_CONV(xy_swap_inverted, -2, -1, 3);
+DEFINE_CONV(xy_rotated_right, 2, -1, 3);
+DEFINE_CONV(xy_swap_yz_inverted, 2, -1, -3);
+
+#define AXIS_DMI_MATCH(_ident, _name, _axis) {		\
+	.ident = _ident,				\
+	.callback = lis3lv02d_dmi_matched,		\
+	.matches = {					\
+		DMI_MATCH(DMI_PRODUCT_NAME, _name)	\
+	},						\
+	.driver_data = &lis3lv02d_axis_##_axis		\
+}
+
+#define AXIS_DMI_MATCH2(_ident, _class1, _name1,	\
+				_class2, _name2,	\
+				_axis) {		\
+	.ident = _ident,				\
+	.callback = lis3lv02d_dmi_matched,		\
+	.matches = {					\
+		DMI_MATCH(DMI_##_class1, _name1),	\
+		DMI_MATCH(DMI_##_class2, _name2),	\
+	},						\
+	.driver_data = &lis3lv02d_axis_##_axis		\
+}
+static const struct dmi_system_id lis3lv02d_dmi_ids[] = {
+	/* product names are truncated to match all kinds of a same model */
+	AXIS_DMI_MATCH("NC64x0", "HP Compaq nc64", x_inverted),
+	AXIS_DMI_MATCH("NC84x0", "HP Compaq nc84", z_inverted),
+	AXIS_DMI_MATCH("NX9420", "HP Compaq nx9420", x_inverted),
+	AXIS_DMI_MATCH("NW9440", "HP Compaq nw9440", x_inverted),
+	AXIS_DMI_MATCH("NC2510", "HP Compaq 2510", y_inverted),
+	AXIS_DMI_MATCH("NC2710", "HP Compaq 2710", xy_swap),
+	AXIS_DMI_MATCH("NC8510", "HP Compaq 8510", xy_swap_inverted),
+	AXIS_DMI_MATCH("HP2133", "HP 2133", xy_rotated_left),
+	AXIS_DMI_MATCH("HP2140", "HP 2140", xy_swap_inverted),
+	AXIS_DMI_MATCH("NC653x", "HP Compaq 653", xy_rotated_left_usd),
+	AXIS_DMI_MATCH("NC6730b", "HP Compaq 6730b", xy_rotated_left_usd),
+	AXIS_DMI_MATCH("NC6730s", "HP Compaq 6730s", xy_swap),
+	AXIS_DMI_MATCH("NC651xx", "HP Compaq 651", xy_rotated_right),
+	AXIS_DMI_MATCH("NC6710x", "HP Compaq 6710", xy_swap_yz_inverted),
+	AXIS_DMI_MATCH("NC6715x", "HP Compaq 6715", y_inverted),
+	AXIS_DMI_MATCH("NC693xx", "HP EliteBook 693", xy_rotated_right),
+	AXIS_DMI_MATCH("NC693xx", "HP EliteBook 853", xy_swap),
+	AXIS_DMI_MATCH("NC854xx", "HP EliteBook 854", y_inverted),
+	AXIS_DMI_MATCH("NC273xx", "HP EliteBook 273", y_inverted),
+	/* Intel-based HP Pavilion dv5 */
+	AXIS_DMI_MATCH2("HPDV5_I",
+			PRODUCT_NAME, "HP Pavilion dv5",
+			BOARD_NAME, "3603",
+			x_inverted),
+	/* AMD-based HP Pavilion dv5 */
+	AXIS_DMI_MATCH2("HPDV5_A",
+			PRODUCT_NAME, "HP Pavilion dv5",
+			BOARD_NAME, "3600",
+			y_inverted),
+	AXIS_DMI_MATCH("DV7", "HP Pavilion dv7", x_inverted),
+	AXIS_DMI_MATCH("HP8710", "HP Compaq 8710", y_inverted),
+	AXIS_DMI_MATCH("HDX18", "HP HDX 18", x_inverted),
+	AXIS_DMI_MATCH("HPB432x", "HP ProBook 432", xy_rotated_left),
+	AXIS_DMI_MATCH("HPB440G3", "HP ProBook 440 G3", x_inverted_usd),
+	AXIS_DMI_MATCH("HPB440G4", "HP ProBook 440 G4", x_inverted),
+	AXIS_DMI_MATCH("HPB442x", "HP ProBook 442", xy_rotated_left),
+	AXIS_DMI_MATCH("HPB450G0", "HP ProBook 450 G0", x_inverted),
+	AXIS_DMI_MATCH("HPB452x", "HP ProBook 452", y_inverted),
+	AXIS_DMI_MATCH("HPB522x", "HP ProBook 522", xy_swap),
+	AXIS_DMI_MATCH("HPB532x", "HP ProBook 532", y_inverted),
+	AXIS_DMI_MATCH("HPB655x", "HP ProBook 655", xy_swap_inverted),
+	AXIS_DMI_MATCH("Mini510x", "HP Mini 510", xy_rotated_left_usd),
+	AXIS_DMI_MATCH("HPB63xx", "HP ProBook 63", xy_swap),
+	AXIS_DMI_MATCH("HPB64xx", "HP ProBook 64", xy_swap),
+	AXIS_DMI_MATCH("HPB64xx", "HP EliteBook 84", xy_swap),
+	AXIS_DMI_MATCH("HPB65xx", "HP ProBook 65", x_inverted),
+	AXIS_DMI_MATCH("HPZBook15", "HP ZBook 15", x_inverted),
+	AXIS_DMI_MATCH("HPZBook17G5", "HP ZBook 17 G5", x_inverted),
+	AXIS_DMI_MATCH("HPZBook17", "HP ZBook 17", xy_swap_yz_inverted),
+	{ NULL, }
+/* Laptop models without axis info (yet):
+ * "NC6910" "HP Compaq 6910"
+ * "NC2400" "HP Compaq nc2400"
+ * "NX74x0" "HP Compaq nx74"
+ * "NX6325" "HP Compaq nx6325"
+ * "NC4400" "HP Compaq nc4400"
+ */
+};
+
+static void hpled_set(struct delayed_led_classdev *led_cdev, enum led_brightness value)
+{
+	struct acpi_device *dev = lis3_dev.bus_priv;
+	unsigned long long ret; /* Not used when writing */
+	union acpi_object in_obj[1];
+	struct acpi_object_list args = { 1, in_obj };
+
+	in_obj[0].type          = ACPI_TYPE_INTEGER;
+	in_obj[0].integer.value = !!value;
+
+	acpi_evaluate_integer(dev->handle, "ALED", &args, &ret);
+}
+
+static struct delayed_led_classdev hpled_led = {
+	.led_classdev = {
+		.name			= "hp::hddprotect",
+		.default_trigger	= "none",
+		.brightness_set		= delayed_sysfs_set,
+		.flags                  = LED_CORE_SUSPENDRESUME,
+	},
+	.set_brightness = hpled_set,
+};
+
+static bool hp_accel_i8042_filter(unsigned char data, unsigned char str,
+				  struct serio *port)
+{
+	static bool extended;
+
+	if (str & I8042_STR_AUXDATA)
+		return false;
+
+	if (data == 0xe0) {
+		extended = true;
+		return true;
+	} else if (unlikely(extended)) {
+		extended = false;
+
+		switch (data) {
+		case ACCEL_1:
+		case ACCEL_2:
+		case ACCEL_3:
+		case ACCEL_4:
+			return true;
+		default:
+			serio_interrupt(port, 0xe0, 0);
+			return false;
+		}
+	}
+
+	return false;
+}
+
+static int lis3lv02d_probe(struct platform_device *device)
+{
+	int ret;
+
+	lis3_dev.bus_priv = ACPI_COMPANION(&device->dev);
+	lis3_dev.init = lis3lv02d_acpi_init;
+	lis3_dev.read = lis3lv02d_acpi_read;
+	lis3_dev.write = lis3lv02d_acpi_write;
+
+	/* obtain IRQ number of our device from ACPI */
+	ret = platform_get_irq_optional(device, 0);
+	if (ret > 0)
+		lis3_dev.irq = ret;
+
+	/* If possible use a "standard" axes order */
+	if (lis3_dev.ac.x && lis3_dev.ac.y && lis3_dev.ac.z) {
+		pr_info("Using custom axes %d,%d,%d\n",
+			lis3_dev.ac.x, lis3_dev.ac.y, lis3_dev.ac.z);
+	} else if (dmi_check_system(lis3lv02d_dmi_ids) == 0) {
+		pr_info("laptop model unknown, using default axes configuration\n");
+		lis3_dev.ac = lis3lv02d_axis_normal;
+	}
+
+	/* call the core layer do its init */
+	ret = lis3lv02d_init_device(&lis3_dev);
+	if (ret)
+		return ret;
+
+	/* filter to remove HPQ6000 accelerometer data
+	 * from keyboard bus stream */
+	if (strstr(dev_name(&device->dev), "HPQ6000"))
+		i8042_install_filter(hp_accel_i8042_filter);
+
+	INIT_WORK(&hpled_led.work, delayed_set_status_worker);
+	ret = led_classdev_register(NULL, &hpled_led.led_classdev);
+	if (ret) {
+		i8042_remove_filter(hp_accel_i8042_filter);
+		lis3lv02d_joystick_disable(&lis3_dev);
+		lis3lv02d_poweroff(&lis3_dev);
+		flush_work(&hpled_led.work);
+		lis3lv02d_remove_fs(&lis3_dev);
+		return ret;
+	}
+
+	return ret;
+}
+
+static int lis3lv02d_remove(struct platform_device *device)
+{
+	i8042_remove_filter(hp_accel_i8042_filter);
+	lis3lv02d_joystick_disable(&lis3_dev);
+	lis3lv02d_poweroff(&lis3_dev);
+
+	led_classdev_unregister(&hpled_led.led_classdev);
+	flush_work(&hpled_led.work);
+
+	return lis3lv02d_remove_fs(&lis3_dev);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int lis3lv02d_suspend(struct device *dev)
+{
+	/* make sure the device is off when we suspend */
+	lis3lv02d_poweroff(&lis3_dev);
+	return 0;
+}
+
+static int lis3lv02d_resume(struct device *dev)
+{
+	lis3lv02d_poweron(&lis3_dev);
+	return 0;
+}
+
+static int lis3lv02d_restore(struct device *dev)
+{
+	lis3lv02d_poweron(&lis3_dev);
+	return 0;
+}
+
+static const struct dev_pm_ops hp_accel_pm = {
+	.suspend = lis3lv02d_suspend,
+	.resume = lis3lv02d_resume,
+	.freeze = lis3lv02d_suspend,
+	.thaw = lis3lv02d_resume,
+	.poweroff = lis3lv02d_suspend,
+	.restore = lis3lv02d_restore,
+};
+
+#define HP_ACCEL_PM (&hp_accel_pm)
+#else
+#define HP_ACCEL_PM NULL
+#endif
+
+/* For the HP MDPS aka 3D Driveguard */
+static struct platform_driver lis3lv02d_driver = {
+	.probe	= lis3lv02d_probe,
+	.remove	= lis3lv02d_remove,
+	.driver	= {
+		.name	= "hp_accel",
+		.pm	= HP_ACCEL_PM,
+		.acpi_match_table = lis3lv02d_device_ids,
+	},
+};
+module_platform_driver(lis3lv02d_driver);
+
+MODULE_DESCRIPTION("Glue between LIS3LV02Dx and HP ACPI BIOS and support for disk protection LED.");
+MODULE_AUTHOR("Yan Burman, Eric Piel, Pavel Machek");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/hp/tc1100-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/hp/tc1100-wmi.c
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  HP Compaq TC1100 Tablet WMI Extras Driver
+ *
+ *  Copyright (C) 2007 Carlos Corbacho <carlos@strangeworlds.co.uk>
+ *  Copyright (C) 2004 Jamey Hicks <jamey.hicks@hp.com>
+ *  Copyright (C) 2001, 2002 Andy Grover <andrew.grover@intel.com>
+ *  Copyright (C) 2001, 2002 Paul Diefenbaugh <paul.s.diefenbaugh@intel.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/acpi.h>
+#include <linux/platform_device.h>
+
+#define GUID "C364AC71-36DB-495A-8494-B439D472A505"
+
+#define TC1100_INSTANCE_WIRELESS		1
+#define TC1100_INSTANCE_JOGDIAL		2
+
+MODULE_AUTHOR("Jamey Hicks, Carlos Corbacho");
+MODULE_DESCRIPTION("HP Compaq TC1100 Tablet WMI Extras");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("wmi:C364AC71-36DB-495A-8494-B439D472A505");
+
+static struct platform_device *tc1100_device;
+
+struct tc1100_data {
+	u32 wireless;
+	u32 jogdial;
+};
+
+#ifdef CONFIG_PM
+static struct tc1100_data suspend_data;
+#endif
+
+/* --------------------------------------------------------------------------
+				Device Management
+   -------------------------------------------------------------------------- */
+
+static int get_state(u32 *out, u8 instance)
+{
+	u32 tmp;
+	acpi_status status;
+	struct acpi_buffer result = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *obj;
+
+	if (!out)
+		return -EINVAL;
+
+	if (instance > 2)
+		return -ENODEV;
+
+	status = wmi_query_block(GUID, instance, &result);
+	if (ACPI_FAILURE(status))
+		return -ENODEV;
+
+	obj = (union acpi_object *) result.pointer;
+	if (obj && obj->type == ACPI_TYPE_INTEGER) {
+		tmp = obj->integer.value;
+	} else {
+		tmp = 0;
+	}
+
+	if (result.length > 0)
+		kfree(result.pointer);
+
+	switch (instance) {
+	case TC1100_INSTANCE_WIRELESS:
+		*out = (tmp == 3) ? 1 : 0;
+		return 0;
+	case TC1100_INSTANCE_JOGDIAL:
+		*out = (tmp == 1) ? 0 : 1;
+		return 0;
+	default:
+		return -ENODEV;
+	}
+}
+
+static int set_state(u32 *in, u8 instance)
+{
+	u32 value;
+	acpi_status status;
+	struct acpi_buffer input;
+
+	if (!in)
+		return -EINVAL;
+
+	if (instance > 2)
+		return -ENODEV;
+
+	switch (instance) {
+	case TC1100_INSTANCE_WIRELESS:
+		value = (*in) ? 1 : 2;
+		break;
+	case TC1100_INSTANCE_JOGDIAL:
+		value = (*in) ? 0 : 1;
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	input.length = sizeof(u32);
+	input.pointer = &value;
+
+	status = wmi_set_block(GUID, instance, &input);
+	if (ACPI_FAILURE(status))
+		return -ENODEV;
+
+	return 0;
+}
+
+/* --------------------------------------------------------------------------
+				FS Interface (/sys)
+   -------------------------------------------------------------------------- */
+
+/*
+ * Read/ write bool sysfs macro
+ */
+#define show_set_bool(value, instance) \
+static ssize_t \
+show_bool_##value(struct device *dev, struct device_attribute *attr, \
+	char *buf) \
+{ \
+	u32 result; \
+	acpi_status status = get_state(&result, instance); \
+	if (ACPI_SUCCESS(status)) \
+		return sprintf(buf, "%d\n", result); \
+	return sprintf(buf, "Read error\n"); \
+} \
+\
+static ssize_t \
+set_bool_##value(struct device *dev, struct device_attribute *attr, \
+	const char *buf, size_t count) \
+{ \
+	u32 tmp = simple_strtoul(buf, NULL, 10); \
+	acpi_status status = set_state(&tmp, instance); \
+		if (ACPI_FAILURE(status)) \
+			return -EINVAL; \
+	return count; \
+} \
+static DEVICE_ATTR(value, S_IRUGO | S_IWUSR, \
+	show_bool_##value, set_bool_##value);
+
+show_set_bool(wireless, TC1100_INSTANCE_WIRELESS);
+show_set_bool(jogdial, TC1100_INSTANCE_JOGDIAL);
+
+static struct attribute *tc1100_attributes[] = {
+	&dev_attr_wireless.attr,
+	&dev_attr_jogdial.attr,
+	NULL
+};
+
+static const struct attribute_group tc1100_attribute_group = {
+	.attrs	= tc1100_attributes,
+};
+
+/* --------------------------------------------------------------------------
+				Driver Model
+   -------------------------------------------------------------------------- */
+
+static int __init tc1100_probe(struct platform_device *device)
+{
+	return sysfs_create_group(&device->dev.kobj, &tc1100_attribute_group);
+}
+
+
+static int tc1100_remove(struct platform_device *device)
+{
+	sysfs_remove_group(&device->dev.kobj, &tc1100_attribute_group);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int tc1100_suspend(struct device *dev)
+{
+	int ret;
+
+	ret = get_state(&suspend_data.wireless, TC1100_INSTANCE_WIRELESS);
+	if (ret)
+		return ret;
+
+	ret = get_state(&suspend_data.jogdial, TC1100_INSTANCE_JOGDIAL);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int tc1100_resume(struct device *dev)
+{
+	int ret;
+
+	ret = set_state(&suspend_data.wireless, TC1100_INSTANCE_WIRELESS);
+	if (ret)
+		return ret;
+
+	ret = set_state(&suspend_data.jogdial, TC1100_INSTANCE_JOGDIAL);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct dev_pm_ops tc1100_pm_ops = {
+	.suspend	= tc1100_suspend,
+	.resume		= tc1100_resume,
+	.freeze		= tc1100_suspend,
+	.restore	= tc1100_resume,
+};
+#endif
+
+static struct platform_driver tc1100_driver = {
+	.driver = {
+		.name = "tc1100-wmi",
+#ifdef CONFIG_PM
+		.pm = &tc1100_pm_ops,
+#endif
+	},
+	.remove = tc1100_remove,
+};
+
+static int __init tc1100_init(void)
+{
+	int error;
+
+	if (!wmi_has_guid(GUID))
+		return -ENODEV;
+
+	tc1100_device = platform_device_alloc("tc1100-wmi", -1);
+	if (!tc1100_device)
+		return -ENOMEM;
+
+	error = platform_device_add(tc1100_device);
+	if (error)
+		goto err_device_put;
+
+	error = platform_driver_probe(&tc1100_driver, tc1100_probe);
+	if (error)
+		goto err_device_del;
+
+	pr_info("HP Compaq TC1100 Tablet WMI Extras loaded\n");
+	return 0;
+
+ err_device_del:
+	platform_device_del(tc1100_device);
+ err_device_put:
+	platform_device_put(tc1100_device);
+	return error;
+}
+
+static void __exit tc1100_exit(void)
+{
+	platform_device_unregister(tc1100_device);
+	platform_driver_unregister(&tc1100_driver);
+}
+
+module_init(tc1100_init);
+module_exit(tc1100_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/huawei-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/huawei-wmi.c
@@ -86,6 +86,8 @@
 	{ KE_IGNORE, 0x293, { KEY_KBDILLUMTOGGLE } },
 	{ KE_IGNORE, 0x294, { KEY_KBDILLUMUP } },
 	{ KE_IGNORE, 0x295, { KEY_KBDILLUMUP } },
+	// Ignore Ambient Light Sensoring
+	{ KE_KEY,    0x2c1, { KEY_RESERVED } },
 	{ KE_END,	 0 }
 };
 
@@ -470,10 +472,17 @@
 
 static int huawei_wmi_battery_add(struct power_supply *battery)
 {
-	device_create_file(&battery->dev, &dev_attr_charge_control_start_threshold);
-	device_create_file(&battery->dev, &dev_attr_charge_control_end_threshold);
+	int err = 0;
 
-	return 0;
+	err = device_create_file(&battery->dev, &dev_attr_charge_control_start_threshold);
+	if (err)
+		return err;
+
+	err = device_create_file(&battery->dev, &dev_attr_charge_control_end_threshold);
+	if (err)
+		device_remove_file(&battery->dev, &dev_attr_charge_control_start_threshold);
+
+	return err;
 }
 
 static int huawei_wmi_battery_remove(struct power_supply *battery)
@@ -753,6 +762,9 @@
 		const char *guid,
 		struct input_dev **idev)
 {
+	acpi_status status;
+	int err;
+
 	*idev = devm_input_allocate_device(dev);
 	if (!*idev)
 		return -ENOMEM;
@@ -762,10 +774,19 @@
 	(*idev)->id.bustype = BUS_HOST;
 	(*idev)->dev.parent = dev;
 
-	return sparse_keymap_setup(*idev, huawei_wmi_keymap, NULL) ||
-		input_register_device(*idev) ||
-		wmi_install_notify_handler(guid, huawei_wmi_input_notify,
-				*idev);
+	err = sparse_keymap_setup(*idev, huawei_wmi_keymap, NULL);
+	if (err)
+		return err;
+
+	err = input_register_device(*idev);
+	if (err)
+		return err;
+
+	status = wmi_install_notify_handler(guid, huawei_wmi_input_notify, *idev);
+	if (ACPI_FAILURE(status))
+		return -EIO;
+
+	return 0;
 }
 
 static void huawei_wmi_input_exit(struct device *dev, const char *guid)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/ideapad-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/ideapad-laptop.c
@@ -136,6 +136,7 @@
 		bool dytc                 : 1;
 		bool fan_mode             : 1;
 		bool fn_lock              : 1;
+		bool set_fn_lock_led      : 1;
 		bool hw_rfkill_switch     : 1;
 		bool kbd_bl               : 1;
 		bool touchpad_ctrl_via_ec : 1;
@@ -1467,6 +1468,9 @@
 		ideapad_input_report(priv, value);
 		break;
 	case 208:
+		if (!priv->features.set_fn_lock_led)
+			break;
+
 		if (!eval_hals(priv->adev->handle, &result)) {
 			bool state = test_bit(HALS_FNLOCK_STATE_BIT, &result);
 
@@ -1480,6 +1484,24 @@
 }
 #endif
 
+/* On some models we need to call exec_sals(SALS_FNLOCK_ON/OFF) to set the LED */
+static const struct dmi_system_id set_fn_lock_led_list[] = {
+	{
+		/* https://bugzilla.kernel.org/show_bug.cgi?id=212671 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo Legion R7000P2020H"),
+		}
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo Legion 5 15ARH05"),
+		}
+	},
+	{}
+};
+
 /*
  * Some ideapads have a hardware rfkill switch, but most do not have one.
  * Reading VPCCMD_R_RF always results in 0 on models without a hardware rfkill,
@@ -1499,15 +1521,39 @@
 	{}
 };
 
+static const struct dmi_system_id no_touchpad_switch_list[] = {
+	{
+	.ident = "Lenovo Yoga 3 Pro 1370",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo YOGA 3"),
+		},
+	},
+	{
+	.ident = "ZhaoYang K4e-IML",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+		DMI_MATCH(DMI_PRODUCT_VERSION, "ZhaoYang K4e-IML"),
+		},
+	},
+	{}
+};
+
 static void ideapad_check_features(struct ideapad_private *priv)
 {
 	acpi_handle handle = priv->adev->handle;
 	unsigned long val;
 
+	priv->features.set_fn_lock_led = dmi_check_system(set_fn_lock_led_list);
 	priv->features.hw_rfkill_switch = dmi_check_system(hw_rfkill_list);
 
 	/* Most ideapads with ELAN0634 touchpad don't use EC touchpad switch */
-	priv->features.touchpad_ctrl_via_ec = !acpi_dev_present("ELAN0634", NULL, -1);
+	if (acpi_dev_present("ELAN0634", NULL, -1))
+		priv->features.touchpad_ctrl_via_ec = 0;
+	else if (dmi_check_system(no_touchpad_switch_list))
+		priv->features.touchpad_ctrl_via_ec = 0;
+	else
+		priv->features.touchpad_ctrl_via_ec = 1;
 
 	if (!read_ec_data(handle, VPCCMD_R_FAN, &val))
 		priv->features.fan_mode = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/Kconfig
@@ -3,19 +3,6 @@
 # Intel x86 Platform Specific Drivers
 #
 
-menuconfig X86_PLATFORM_DRIVERS_INTEL
-	bool "Intel x86 Platform Specific Device Drivers"
-	default y
-	help
-	  Say Y here to get to see options for device drivers for
-	  various Intel x86 platforms, including vendor-specific
-	  drivers. This option alone does not add any kernel code.
-
-	  If you say N, all options in this submenu will be skipped
-	  and disabled.
-
-if X86_PLATFORM_DRIVERS_INTEL
-
 source "drivers/platform/x86/intel/atomisp2/Kconfig"
 source "drivers/platform/x86/intel/int1092/Kconfig"
 source "drivers/platform/x86/intel/int33fe/Kconfig"
@@ -167,5 +154,3 @@
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called intel-uncore-frequency.
-
-endif # X86_PLATFORM_DRIVERS_INTEL
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/bxtwc_tmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/bxtwc_tmu.c
@@ -48,9 +48,8 @@
 static int bxt_wcove_tmu_probe(struct platform_device *pdev)
 {
 	struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
-	struct regmap_irq_chip_data *regmap_irq_chip;
 	struct wcove_tmu *wctmu;
-	int ret, virq, irq;
+	int ret;
 
 	wctmu = devm_kzalloc(&pdev->dev, sizeof(*wctmu), GFP_KERNEL);
 	if (!wctmu)
@@ -59,27 +58,18 @@
 	wctmu->dev = &pdev->dev;
 	wctmu->regmap = pmic->regmap;
 
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0)
-		return irq;
+	wctmu->irq = platform_get_irq(pdev, 0);
+	if (wctmu->irq < 0)
+		return wctmu->irq;
 
-	regmap_irq_chip = pmic->irq_chip_data_tmu;
-	virq = regmap_irq_get_virq(regmap_irq_chip, irq);
-	if (virq < 0) {
-		dev_err(&pdev->dev,
-			"failed to get virtual interrupt=%d\n", irq);
-		return virq;
-	}
-
-	ret = devm_request_threaded_irq(&pdev->dev, virq,
+	ret = devm_request_threaded_irq(&pdev->dev, wctmu->irq,
 					NULL, bxt_wcove_tmu_irq_handler,
 					IRQF_ONESHOT, "bxt_wcove_tmu", wctmu);
 	if (ret) {
 		dev_err(&pdev->dev, "request irq failed: %d,virq: %d\n",
-							ret, virq);
+			ret, wctmu->irq);
 		return ret;
 	}
-	wctmu->irq = virq;
 
 	/* Unmask TMU second level Wake & System alarm */
 	regmap_update_bits(wctmu->regmap, BXTWC_MTMUIRQ_REG,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/hid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/hid.c
@@ -27,6 +27,9 @@
 	{"INTC1051", 0},
 	{"INTC1054", 0},
 	{"INTC1070", 0},
+	{"INTC1076", 0},
+	{"INTC1077", 0},
+	{"INTC1078", 0},
 	{"", 0},
 };
 MODULE_DEVICE_TABLE(acpi, intel_hid_ids);
@@ -99,6 +102,20 @@
 			DMI_MATCH(DMI_PRODUCT_FAMILY, "ThinkPad X1 Tablet Gen 2"),
 		},
 	},
+	{
+		.ident = "Microsoft Surface Go 3",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go 3"),
+		},
+	},
+	{
+		.ident = "Microsoft Surface Go 3",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go 3"),
+		},
+	},
 	{ }
 };
 
@@ -115,6 +132,18 @@
 			DMI_MATCH(DMI_PRODUCT_NAME, "HP Spectre x360 Convertible 15-df0xxx"),
 		},
 	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "HP"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Elite Dragonfly G2 Notebook PC"),
+		},
+	},
 	{ }
 };
 
@@ -231,7 +260,7 @@
 
 	method_name = (char *)intel_hid_dsm_fn_to_method[fn_index];
 
-	if (!(intel_hid_dsm_fn_mask & fn_index))
+	if (!(intel_hid_dsm_fn_mask & BIT(fn_index)))
 		goto skip_dsm_eval;
 
 	obj = acpi_evaluate_dsm_typed(handle, &intel_dsm_guid,
@@ -585,7 +614,7 @@
 static int intel_hid_probe(struct platform_device *device)
 {
 	acpi_handle handle = ACPI_HANDLE(&device->dev);
-	unsigned long long mode;
+	unsigned long long mode, dummy;
 	struct intel_hid_priv *priv;
 	acpi_status status;
 	int err;
@@ -650,18 +679,15 @@
 	if (err)
 		goto err_remove_notify;
 
-	if (priv->array) {
-		unsigned long long dummy;
+	intel_button_array_enable(&device->dev, true);
 
-		intel_button_array_enable(&device->dev, true);
-
-		/* Call button load method to enable HID power button */
-		if (!intel_hid_evaluate_method(handle, INTEL_HID_DSM_BTNL_FN,
-					       &dummy)) {
-			dev_warn(&device->dev,
-				 "failed to enable HID power button\n");
-		}
-	}
+	/*
+	 * Call button load method to enable HID power button
+	 * Always do this since it activates events on some devices without
+	 * a button array too.
+	 */
+	if (!intel_hid_evaluate_method(handle, INTEL_HID_DSM_BTNL_FN, &dummy))
+		dev_warn(&device->dev, "failed to enable HID power button\n");
 
 	device_init_wakeup(&device->dev, true);
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/int3472/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/int3472/Makefile
@@ -1,5 +1,4 @@
-obj-$(CONFIG_INTEL_SKL_INT3472)		+= intel_skl_int3472.o
-intel_skl_int3472-y			:= intel_skl_int3472_common.o \
-					   intel_skl_int3472_discrete.o \
-					   intel_skl_int3472_tps68470.o \
-					   intel_skl_int3472_clk_and_regulator.o
+obj-$(CONFIG_INTEL_SKL_INT3472)		+= intel_skl_int3472_discrete.o \
+					   intel_skl_int3472_tps68470.o
+intel_skl_int3472_discrete-y		:= discrete.o clk_and_regulator.o common.o
+intel_skl_int3472_tps68470-y		:= tps68470.o common.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/int3472/clk_and_regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/int3472/clk_and_regulator.c
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Author: Dan Scally <djrscally@gmail.com> */
+
+#include <linux/acpi.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/driver.h>
+#include <linux/slab.h>
+
+#include "common.h"
+
+/*
+ * The regulators have to have .ops to be valid, but the only ops we actually
+ * support are .enable and .disable which are handled via .ena_gpiod. Pass an
+ * empty struct to clear the check without lying about capabilities.
+ */
+static const struct regulator_ops int3472_gpio_regulator_ops;
+
+static int skl_int3472_clk_prepare(struct clk_hw *hw)
+{
+	struct int3472_gpio_clock *clk = to_int3472_clk(hw);
+
+	gpiod_set_value_cansleep(clk->ena_gpio, 1);
+	gpiod_set_value_cansleep(clk->led_gpio, 1);
+
+	return 0;
+}
+
+static void skl_int3472_clk_unprepare(struct clk_hw *hw)
+{
+	struct int3472_gpio_clock *clk = to_int3472_clk(hw);
+
+	gpiod_set_value_cansleep(clk->ena_gpio, 0);
+	gpiod_set_value_cansleep(clk->led_gpio, 0);
+}
+
+static int skl_int3472_clk_enable(struct clk_hw *hw)
+{
+	/*
+	 * We're just turning a GPIO on to enable the clock, which operation
+	 * has the potential to sleep. Given .enable() cannot sleep, but
+	 * .prepare() can, we toggle the GPIO in .prepare() instead. Thus,
+	 * nothing to do here.
+	 */
+	return 0;
+}
+
+static void skl_int3472_clk_disable(struct clk_hw *hw)
+{
+	/* Likewise, nothing to do here... */
+}
+
+static unsigned int skl_int3472_get_clk_frequency(struct int3472_discrete_device *int3472)
+{
+	union acpi_object *obj;
+	unsigned int freq;
+
+	obj = skl_int3472_get_acpi_buffer(int3472->sensor, "SSDB");
+	if (IS_ERR(obj))
+		return 0; /* report rate as 0 on error */
+
+	if (obj->buffer.length < CIO2_SENSOR_SSDB_MCLKSPEED_OFFSET + sizeof(u32)) {
+		dev_err(int3472->dev, "The buffer is too small\n");
+		kfree(obj);
+		return 0;
+	}
+
+	freq = *(u32 *)(obj->buffer.pointer + CIO2_SENSOR_SSDB_MCLKSPEED_OFFSET);
+
+	kfree(obj);
+	return freq;
+}
+
+static unsigned long skl_int3472_clk_recalc_rate(struct clk_hw *hw,
+						 unsigned long parent_rate)
+{
+	struct int3472_gpio_clock *clk = to_int3472_clk(hw);
+
+	return clk->frequency;
+}
+
+static const struct clk_ops skl_int3472_clock_ops = {
+	.prepare = skl_int3472_clk_prepare,
+	.unprepare = skl_int3472_clk_unprepare,
+	.enable = skl_int3472_clk_enable,
+	.disable = skl_int3472_clk_disable,
+	.recalc_rate = skl_int3472_clk_recalc_rate,
+};
+
+int skl_int3472_register_clock(struct int3472_discrete_device *int3472)
+{
+	struct clk_init_data init = {
+		.ops = &skl_int3472_clock_ops,
+		.flags = CLK_GET_RATE_NOCACHE,
+	};
+	int ret;
+
+	init.name = kasprintf(GFP_KERNEL, "%s-clk",
+			      acpi_dev_name(int3472->adev));
+	if (!init.name)
+		return -ENOMEM;
+
+	int3472->clock.frequency = skl_int3472_get_clk_frequency(int3472);
+
+	int3472->clock.clk_hw.init = &init;
+	int3472->clock.clk = clk_register(&int3472->adev->dev,
+					  &int3472->clock.clk_hw);
+	if (IS_ERR(int3472->clock.clk)) {
+		ret = PTR_ERR(int3472->clock.clk);
+		goto out_free_init_name;
+	}
+
+	int3472->clock.cl = clkdev_create(int3472->clock.clk, NULL,
+					  int3472->sensor_name);
+	if (!int3472->clock.cl) {
+		ret = -ENOMEM;
+		goto err_unregister_clk;
+	}
+
+	kfree(init.name);
+	return 0;
+
+err_unregister_clk:
+	clk_unregister(int3472->clock.clk);
+out_free_init_name:
+	kfree(init.name);
+
+	return ret;
+}
+
+void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472)
+{
+	clkdev_drop(int3472->clock.cl);
+	clk_unregister(int3472->clock.clk);
+}
+
+int skl_int3472_register_regulator(struct int3472_discrete_device *int3472,
+				   struct acpi_resource_gpio *agpio)
+{
+	const struct int3472_sensor_config *sensor_config;
+	char *path = agpio->resource_source.string_ptr;
+	struct regulator_consumer_supply supply_map;
+	struct regulator_init_data init_data = { };
+	struct regulator_config cfg = { };
+	int ret;
+
+	sensor_config = int3472->sensor_config;
+	if (IS_ERR(sensor_config)) {
+		dev_err(int3472->dev, "No sensor module config\n");
+		return PTR_ERR(sensor_config);
+	}
+
+	if (!sensor_config->supply_map.supply) {
+		dev_err(int3472->dev, "No supply name defined\n");
+		return -ENODEV;
+	}
+
+	init_data.constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS;
+	init_data.num_consumer_supplies = 1;
+	supply_map = sensor_config->supply_map;
+	supply_map.dev_name = int3472->sensor_name;
+	init_data.consumer_supplies = &supply_map;
+
+	snprintf(int3472->regulator.regulator_name,
+		 sizeof(int3472->regulator.regulator_name), "%s-regulator",
+		 acpi_dev_name(int3472->adev));
+	snprintf(int3472->regulator.supply_name,
+		 GPIO_REGULATOR_SUPPLY_NAME_LENGTH, "supply-0");
+
+	int3472->regulator.rdesc = INT3472_REGULATOR(
+						int3472->regulator.regulator_name,
+						int3472->regulator.supply_name,
+						&int3472_gpio_regulator_ops);
+
+	int3472->regulator.gpio = acpi_get_and_request_gpiod(path, agpio->pin_table[0],
+							     "int3472,regulator");
+	if (IS_ERR(int3472->regulator.gpio)) {
+		dev_err(int3472->dev, "Failed to get regulator GPIO line\n");
+		return PTR_ERR(int3472->regulator.gpio);
+	}
+
+	/* Ensure the pin is in output mode and non-active state */
+	gpiod_direction_output(int3472->regulator.gpio, 0);
+
+	cfg.dev = &int3472->adev->dev;
+	cfg.init_data = &init_data;
+	cfg.ena_gpiod = int3472->regulator.gpio;
+
+	int3472->regulator.rdev = regulator_register(&int3472->regulator.rdesc,
+						     &cfg);
+	if (IS_ERR(int3472->regulator.rdev)) {
+		ret = PTR_ERR(int3472->regulator.rdev);
+		goto err_free_gpio;
+	}
+
+	return 0;
+
+err_free_gpio:
+	gpiod_put(int3472->regulator.gpio);
+
+	return ret;
+}
+
+void skl_int3472_unregister_regulator(struct int3472_discrete_device *int3472)
+{
+	regulator_unregister(int3472->regulator.rdev);
+	gpiod_put(int3472->regulator.gpio);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/int3472/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/int3472/common.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Author: Dan Scally <djrscally@gmail.com> */
+
+#include <linux/acpi.h>
+#include <linux/slab.h>
+
+#include "common.h"
+
+union acpi_object *skl_int3472_get_acpi_buffer(struct acpi_device *adev, char *id)
+{
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	acpi_handle handle = adev->handle;
+	union acpi_object *obj;
+	acpi_status status;
+
+	status = acpi_evaluate_object(handle, id, NULL, &buffer);
+	if (ACPI_FAILURE(status))
+		return ERR_PTR(-ENODEV);
+
+	obj = buffer.pointer;
+	if (!obj)
+		return ERR_PTR(-ENODEV);
+
+	if (obj->type != ACPI_TYPE_BUFFER) {
+		acpi_handle_err(handle, "%s object is not an ACPI buffer\n", id);
+		kfree(obj);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return obj;
+}
+
+int skl_int3472_fill_cldb(struct acpi_device *adev, struct int3472_cldb *cldb)
+{
+	union acpi_object *obj;
+	int ret;
+
+	obj = skl_int3472_get_acpi_buffer(adev, "CLDB");
+	if (IS_ERR(obj))
+		return PTR_ERR(obj);
+
+	if (obj->buffer.length > sizeof(*cldb)) {
+		acpi_handle_err(adev->handle, "The CLDB buffer is too large\n");
+		ret = -EINVAL;
+		goto out_free_obj;
+	}
+
+	memcpy(cldb, obj->buffer.pointer, obj->buffer.length);
+	ret = 0;
+
+out_free_obj:
+	kfree(obj);
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/int3472/common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/int3472/common.h
@@ -0,0 +1,119 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Author: Dan Scally <djrscally@gmail.com> */
+
+#ifndef _INTEL_SKL_INT3472_H
+#define _INTEL_SKL_INT3472_H
+
+#include <linux/clk-provider.h>
+#include <linux/gpio/machine.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/types.h>
+
+/* FIXME drop this once the I2C_DEV_NAME_FORMAT macro has been added to include/linux/i2c.h */
+#ifndef I2C_DEV_NAME_FORMAT
+#define I2C_DEV_NAME_FORMAT					"i2c-%s"
+#endif
+
+/* PMIC GPIO Types */
+#define INT3472_GPIO_TYPE_RESET					0x00
+#define INT3472_GPIO_TYPE_POWERDOWN				0x01
+#define INT3472_GPIO_TYPE_POWER_ENABLE				0x0b
+#define INT3472_GPIO_TYPE_CLK_ENABLE				0x0c
+#define INT3472_GPIO_TYPE_PRIVACY_LED				0x0d
+
+#define INT3472_PDEV_MAX_NAME_LEN				23
+#define INT3472_MAX_SENSOR_GPIOS				3
+
+#define GPIO_REGULATOR_NAME_LENGTH				21
+#define GPIO_REGULATOR_SUPPLY_NAME_LENGTH			9
+
+#define CIO2_SENSOR_SSDB_MCLKSPEED_OFFSET			86
+
+#define INT3472_REGULATOR(_name, _supply, _ops)			\
+	(const struct regulator_desc) {				\
+		.name = _name,					\
+		.supply_name = _supply,				\
+		.type = REGULATOR_VOLTAGE,			\
+		.ops = _ops,					\
+		.owner = THIS_MODULE,				\
+	}
+
+#define to_int3472_clk(hw)					\
+	container_of(hw, struct int3472_gpio_clock, clk_hw)
+
+#define to_int3472_device(clk)					\
+	container_of(clk, struct int3472_discrete_device, clock)
+
+struct acpi_device;
+struct i2c_client;
+struct platform_device;
+
+struct int3472_cldb {
+	u8 version;
+	/*
+	 * control logic type
+	 * 0: UNKNOWN
+	 * 1: DISCRETE(CRD-D)
+	 * 2: PMIC TPS68470
+	 * 3: PMIC uP6641
+	 */
+	u8 control_logic_type;
+	u8 control_logic_id;
+	u8 sensor_card_sku;
+	u8 reserved[28];
+};
+
+struct int3472_gpio_function_remap {
+	const char *documented;
+	const char *actual;
+};
+
+struct int3472_sensor_config {
+	const char *sensor_module_name;
+	struct regulator_consumer_supply supply_map;
+	const struct int3472_gpio_function_remap *function_maps;
+};
+
+struct int3472_discrete_device {
+	struct acpi_device *adev;
+	struct device *dev;
+	struct acpi_device *sensor;
+	const char *sensor_name;
+
+	const struct int3472_sensor_config *sensor_config;
+
+	struct int3472_gpio_regulator {
+		char regulator_name[GPIO_REGULATOR_NAME_LENGTH];
+		char supply_name[GPIO_REGULATOR_SUPPLY_NAME_LENGTH];
+		struct gpio_desc *gpio;
+		struct regulator_dev *rdev;
+		struct regulator_desc rdesc;
+	} regulator;
+
+	struct int3472_gpio_clock {
+		struct clk *clk;
+		struct clk_hw clk_hw;
+		struct clk_lookup *cl;
+		struct gpio_desc *ena_gpio;
+		struct gpio_desc *led_gpio;
+		u32 frequency;
+	} clock;
+
+	unsigned int ngpios; /* how many GPIOs have we seen */
+	unsigned int n_sensor_gpios; /* how many have we mapped to sensor */
+	struct gpiod_lookup_table gpios;
+};
+
+union acpi_object *skl_int3472_get_acpi_buffer(struct acpi_device *adev,
+					       char *id);
+int skl_int3472_fill_cldb(struct acpi_device *adev, struct int3472_cldb *cldb);
+
+int skl_int3472_register_clock(struct int3472_discrete_device *int3472);
+void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472);
+
+int skl_int3472_register_regulator(struct int3472_discrete_device *int3472,
+				   struct acpi_resource_gpio *agpio);
+void skl_int3472_unregister_regulator(struct int3472_discrete_device *int3472);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/int3472/discrete.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/int3472/discrete.c
@@ -0,0 +1,439 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Author: Dan Scally <djrscally@gmail.com> */
+
+#include <linux/acpi.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/machine.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/overflow.h>
+#include <linux/platform_device.h>
+#include <linux/uuid.h>
+
+#include "common.h"
+
+/*
+ * 79234640-9e10-4fea-a5c1-b5aa8b19756f
+ * This _DSM GUID returns information about the GPIO lines mapped to a
+ * discrete INT3472 device. Function number 1 returns a count of the GPIO
+ * lines that are mapped. Subsequent functions return 32 bit ints encoding
+ * information about the GPIO line, including its purpose.
+ */
+static const guid_t int3472_gpio_guid =
+	GUID_INIT(0x79234640, 0x9e10, 0x4fea,
+		  0xa5, 0xc1, 0xb5, 0xaa, 0x8b, 0x19, 0x75, 0x6f);
+
+/*
+ * 822ace8f-2814-4174-a56b-5f029fe079ee
+ * This _DSM GUID returns a string from the sensor device, which acts as a
+ * module identifier.
+ */
+static const guid_t cio2_sensor_module_guid =
+	GUID_INIT(0x822ace8f, 0x2814, 0x4174,
+		  0xa5, 0x6b, 0x5f, 0x02, 0x9f, 0xe0, 0x79, 0xee);
+
+/*
+ * Here follows platform specific mapping information that we can pass to
+ * the functions mapping resources to the sensors. Where the sensors have
+ * a power enable pin defined in DSDT we need to provide a supply name so
+ * the sensor drivers can find the regulator. The device name will be derived
+ * from the sensor's ACPI device within the code. Optionally, we can provide a
+ * NULL terminated array of function name mappings to deal with any platform
+ * specific deviations from the documented behaviour of GPIOs.
+ *
+ * Map a GPIO function name to NULL to prevent the driver from mapping that
+ * GPIO at all.
+ */
+
+static const struct int3472_gpio_function_remap ov2680_gpio_function_remaps[] = {
+	{ "reset", NULL },
+	{ "powerdown", "reset" },
+	{ }
+};
+
+static const struct int3472_sensor_config int3472_sensor_configs[] = {
+	/* Lenovo Miix 510-12ISK - OV2680, Front */
+	{ "GNDF140809R", { 0 }, ov2680_gpio_function_remaps },
+	/* Lenovo Miix 510-12ISK - OV5648, Rear */
+	{ "GEFF150023R", REGULATOR_SUPPLY("avdd", NULL), NULL },
+	/* Surface Go 1&2 - OV5693, Front */
+	{ "YHCU", REGULATOR_SUPPLY("avdd", NULL), NULL },
+};
+
+static const struct int3472_sensor_config *
+skl_int3472_get_sensor_module_config(struct int3472_discrete_device *int3472)
+{
+	union acpi_object *obj;
+	unsigned int i;
+
+	obj = acpi_evaluate_dsm_typed(int3472->sensor->handle,
+				      &cio2_sensor_module_guid, 0x00,
+				      0x01, NULL, ACPI_TYPE_STRING);
+
+	if (!obj) {
+		dev_err(int3472->dev,
+			"Failed to get sensor module string from _DSM\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	if (obj->string.type != ACPI_TYPE_STRING) {
+		dev_err(int3472->dev,
+			"Sensor _DSM returned a non-string value\n");
+
+		ACPI_FREE(obj);
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(int3472_sensor_configs); i++) {
+		if (!strcmp(int3472_sensor_configs[i].sensor_module_name,
+			    obj->string.pointer))
+			break;
+	}
+
+	ACPI_FREE(obj);
+
+	if (i >= ARRAY_SIZE(int3472_sensor_configs))
+		return ERR_PTR(-EINVAL);
+
+	return &int3472_sensor_configs[i];
+}
+
+static int skl_int3472_map_gpio_to_sensor(struct int3472_discrete_device *int3472,
+					  struct acpi_resource_gpio *agpio,
+					  const char *func, u32 polarity)
+{
+	const struct int3472_sensor_config *sensor_config;
+	char *path = agpio->resource_source.string_ptr;
+	struct gpiod_lookup *table_entry;
+	struct acpi_device *adev;
+	acpi_handle handle;
+	acpi_status status;
+	int ret;
+
+	if (int3472->n_sensor_gpios >= INT3472_MAX_SENSOR_GPIOS) {
+		dev_warn(int3472->dev, "Too many GPIOs mapped\n");
+		return -EINVAL;
+	}
+
+	sensor_config = int3472->sensor_config;
+	if (!IS_ERR(sensor_config) && sensor_config->function_maps) {
+		const struct int3472_gpio_function_remap *remap;
+
+		for (remap = sensor_config->function_maps; remap->documented; remap++) {
+			if (!strcmp(func, remap->documented)) {
+				func = remap->actual;
+				break;
+			}
+		}
+	}
+
+	/* Functions mapped to NULL should not be mapped to the sensor */
+	if (!func)
+		return 0;
+
+	status = acpi_get_handle(NULL, path, &handle);
+	if (ACPI_FAILURE(status))
+		return -EINVAL;
+
+	ret = acpi_bus_get_device(handle, &adev);
+	if (ret)
+		return -ENODEV;
+
+	table_entry = &int3472->gpios.table[int3472->n_sensor_gpios];
+	table_entry->key = acpi_dev_name(adev);
+	table_entry->chip_hwnum = agpio->pin_table[0];
+	table_entry->con_id = func;
+	table_entry->idx = 0;
+	table_entry->flags = polarity;
+
+	int3472->n_sensor_gpios++;
+
+	return 0;
+}
+
+static int skl_int3472_map_gpio_to_clk(struct int3472_discrete_device *int3472,
+				       struct acpi_resource_gpio *agpio, u8 type)
+{
+	char *path = agpio->resource_source.string_ptr;
+	u16 pin = agpio->pin_table[0];
+	struct gpio_desc *gpio;
+
+	switch (type) {
+	case INT3472_GPIO_TYPE_CLK_ENABLE:
+		gpio = acpi_get_and_request_gpiod(path, pin, "int3472,clk-enable");
+		if (IS_ERR(gpio))
+			return (PTR_ERR(gpio));
+
+		int3472->clock.ena_gpio = gpio;
+		/* Ensure the pin is in output mode and non-active state */
+		gpiod_direction_output(int3472->clock.ena_gpio, 0);
+		break;
+	case INT3472_GPIO_TYPE_PRIVACY_LED:
+		gpio = acpi_get_and_request_gpiod(path, pin, "int3472,privacy-led");
+		if (IS_ERR(gpio))
+			return (PTR_ERR(gpio));
+
+		int3472->clock.led_gpio = gpio;
+		/* Ensure the pin is in output mode and non-active state */
+		gpiod_direction_output(int3472->clock.led_gpio, 0);
+		break;
+	default:
+		dev_err(int3472->dev, "Invalid GPIO type 0x%02x for clock\n", type);
+		break;
+	}
+
+	return 0;
+}
+
+/**
+ * skl_int3472_handle_gpio_resources: Map PMIC resources to consuming sensor
+ * @ares: A pointer to a &struct acpi_resource
+ * @data: A pointer to a &struct int3472_discrete_device
+ *
+ * This function handles GPIO resources that are against an INT3472
+ * ACPI device, by checking the value of the corresponding _DSM entry.
+ * This will return a 32bit int, where the lowest byte represents the
+ * function of the GPIO pin:
+ *
+ * 0x00 Reset
+ * 0x01 Power down
+ * 0x0b Power enable
+ * 0x0c Clock enable
+ * 0x0d Privacy LED
+ *
+ * There are some known platform specific quirks where that does not quite
+ * hold up; for example where a pin with type 0x01 (Power down) is mapped to
+ * a sensor pin that performs a reset function or entries in _CRS and _DSM that
+ * do not actually correspond to a physical connection. These will be handled
+ * by the mapping sub-functions.
+ *
+ * GPIOs will either be mapped directly to the sensor device or else used
+ * to create clocks and regulators via the usual frameworks.
+ *
+ * Return:
+ * * 1		- To continue the loop
+ * * 0		- When all resources found are handled properly.
+ * * -EINVAL	- If the resource is not a GPIO IO resource
+ * * -ENODEV	- If the resource has no corresponding _DSM entry
+ * * -Other	- Errors propagated from one of the sub-functions.
+ */
+static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,
+					     void *data)
+{
+	struct int3472_discrete_device *int3472 = data;
+	struct acpi_resource_gpio *agpio;
+	union acpi_object *obj;
+	const char *err_msg;
+	int ret;
+	u8 type;
+
+	if (!acpi_gpio_get_io_resource(ares, &agpio))
+		return 1;
+
+	/*
+	 * ngpios + 2 because the index of this _DSM function is 1-based and
+	 * the first function is just a count.
+	 */
+	obj = acpi_evaluate_dsm_typed(int3472->adev->handle,
+				      &int3472_gpio_guid, 0x00,
+				      int3472->ngpios + 2,
+				      NULL, ACPI_TYPE_INTEGER);
+
+	if (!obj) {
+		dev_warn(int3472->dev, "No _DSM entry for GPIO pin %u\n",
+			 agpio->pin_table[0]);
+		return 1;
+	}
+
+	type = obj->integer.value & 0xff;
+
+	switch (type) {
+	case INT3472_GPIO_TYPE_RESET:
+		ret = skl_int3472_map_gpio_to_sensor(int3472, agpio, "reset",
+						     GPIO_ACTIVE_LOW);
+		if (ret)
+			err_msg = "Failed to map reset pin to sensor\n";
+
+		break;
+	case INT3472_GPIO_TYPE_POWERDOWN:
+		ret = skl_int3472_map_gpio_to_sensor(int3472, agpio, "powerdown",
+						     GPIO_ACTIVE_LOW);
+		if (ret)
+			err_msg = "Failed to map powerdown pin to sensor\n";
+
+		break;
+	case INT3472_GPIO_TYPE_CLK_ENABLE:
+	case INT3472_GPIO_TYPE_PRIVACY_LED:
+		ret = skl_int3472_map_gpio_to_clk(int3472, agpio, type);
+		if (ret)
+			err_msg = "Failed to map GPIO to clock\n";
+
+		break;
+	case INT3472_GPIO_TYPE_POWER_ENABLE:
+		ret = skl_int3472_register_regulator(int3472, agpio);
+		if (ret)
+			err_msg = "Failed to map regulator to sensor\n";
+
+		break;
+	default:
+		dev_warn(int3472->dev,
+			 "GPIO type 0x%02x unknown; the sensor may not work\n",
+			 type);
+		ret = 1;
+		break;
+	}
+
+	int3472->ngpios++;
+	ACPI_FREE(obj);
+
+	if (ret < 0)
+		return dev_err_probe(int3472->dev, ret, err_msg);
+
+	return ret;
+}
+
+static int skl_int3472_parse_crs(struct int3472_discrete_device *int3472)
+{
+	LIST_HEAD(resource_list);
+	int ret;
+
+	/*
+	 * No error check, because not having a sensor config is not necessarily
+	 * a failure mode.
+	 */
+	int3472->sensor_config = skl_int3472_get_sensor_module_config(int3472);
+
+	ret = acpi_dev_get_resources(int3472->adev, &resource_list,
+				     skl_int3472_handle_gpio_resources,
+				     int3472);
+	if (ret < 0)
+		return ret;
+
+	acpi_dev_free_resource_list(&resource_list);
+
+	/*
+	 * If we find no clock enable GPIO pin then the privacy LED won't work.
+	 * We've never seen that situation, but it's possible. Warn the user so
+	 * it's clear what's happened.
+	 */
+	if (int3472->clock.ena_gpio) {
+		ret = skl_int3472_register_clock(int3472);
+		if (ret)
+			return ret;
+	} else {
+		if (int3472->clock.led_gpio)
+			dev_warn(int3472->dev,
+				 "No clk GPIO. The privacy LED won't work\n");
+	}
+
+	int3472->gpios.dev_id = int3472->sensor_name;
+	gpiod_add_lookup_table(&int3472->gpios);
+
+	return 0;
+}
+
+static int skl_int3472_discrete_remove(struct platform_device *pdev);
+
+static int skl_int3472_discrete_probe(struct platform_device *pdev)
+{
+	struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+	struct int3472_discrete_device *int3472;
+	struct int3472_cldb cldb;
+	int ret;
+
+	ret = skl_int3472_fill_cldb(adev, &cldb);
+	if (ret) {
+		dev_err(&pdev->dev, "Couldn't fill CLDB structure\n");
+		return ret;
+	}
+
+	if (cldb.control_logic_type != 1) {
+		dev_err(&pdev->dev, "Unsupported control logic type %u\n",
+			cldb.control_logic_type);
+		return -EINVAL;
+	}
+
+	/* Max num GPIOs we've seen plus a terminator */
+	int3472 = devm_kzalloc(&pdev->dev, struct_size(int3472, gpios.table,
+			       INT3472_MAX_SENSOR_GPIOS + 1), GFP_KERNEL);
+	if (!int3472)
+		return -ENOMEM;
+
+	int3472->adev = adev;
+	int3472->dev = &pdev->dev;
+	platform_set_drvdata(pdev, int3472);
+
+	int3472->sensor = acpi_dev_get_first_consumer_dev(adev);
+	if (!int3472->sensor) {
+		dev_err(&pdev->dev, "INT3472 seems to have no dependents.\n");
+		return -ENODEV;
+	}
+
+	int3472->sensor_name = devm_kasprintf(int3472->dev, GFP_KERNEL,
+					      I2C_DEV_NAME_FORMAT,
+					      acpi_dev_name(int3472->sensor));
+	if (!int3472->sensor_name) {
+		ret = -ENOMEM;
+		goto err_put_sensor;
+	}
+
+	/*
+	 * Initialising this list means we can call gpiod_remove_lookup_table()
+	 * in failure paths without issue.
+	 */
+	INIT_LIST_HEAD(&int3472->gpios.list);
+
+	ret = skl_int3472_parse_crs(int3472);
+	if (ret) {
+		skl_int3472_discrete_remove(pdev);
+		return ret;
+	}
+
+	return 0;
+
+err_put_sensor:
+	acpi_dev_put(int3472->sensor);
+
+	return ret;
+}
+
+static int skl_int3472_discrete_remove(struct platform_device *pdev)
+{
+	struct int3472_discrete_device *int3472 = platform_get_drvdata(pdev);
+
+	gpiod_remove_lookup_table(&int3472->gpios);
+
+	if (int3472->clock.cl)
+		skl_int3472_unregister_clock(int3472);
+
+	gpiod_put(int3472->clock.ena_gpio);
+	gpiod_put(int3472->clock.led_gpio);
+
+	skl_int3472_unregister_regulator(int3472);
+
+	return 0;
+}
+
+static const struct acpi_device_id int3472_device_id[] = {
+	{ "INT3472", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, int3472_device_id);
+
+static struct platform_driver int3472_discrete = {
+	.driver = {
+		.name = "int3472-discrete",
+		.acpi_match_table = int3472_device_id,
+	},
+	.probe = skl_int3472_discrete_probe,
+	.remove = skl_int3472_discrete_remove,
+};
+module_platform_driver(int3472_discrete);
+
+MODULE_DESCRIPTION("Intel SkyLake INT3472 ACPI Discrete Device Driver");
+MODULE_AUTHOR("Daniel Scally <djrscally@gmail.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/int3472/tps68470.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/int3472/tps68470.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Author: Dan Scally <djrscally@gmail.com> */
+
+#include <linux/i2c.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/tps68470.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "common.h"
+
+#define DESIGNED_FOR_CHROMEOS		1
+#define DESIGNED_FOR_WINDOWS		2
+
+static const struct mfd_cell tps68470_cros[] = {
+	{ .name = "tps68470-gpio" },
+	{ .name = "tps68470_pmic_opregion" },
+};
+
+static const struct mfd_cell tps68470_win[] = {
+	{ .name = "tps68470-gpio" },
+	{ .name = "tps68470-clk" },
+	{ .name = "tps68470-regulator" },
+};
+
+static const struct regmap_config tps68470_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = TPS68470_REG_MAX,
+};
+
+static int tps68470_chip_init(struct device *dev, struct regmap *regmap)
+{
+	unsigned int version;
+	int ret;
+
+	/* Force software reset */
+	ret = regmap_write(regmap, TPS68470_REG_RESET, TPS68470_REG_RESET_MASK);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(regmap, TPS68470_REG_REVID, &version);
+	if (ret) {
+		dev_err(dev, "Failed to read revision register: %d\n", ret);
+		return ret;
+	}
+
+	dev_info(dev, "TPS68470 REVID: 0x%02x\n", version);
+
+	return 0;
+}
+
+/** skl_int3472_tps68470_calc_type: Check what platform a device is designed for
+ * @adev: A pointer to a &struct acpi_device
+ *
+ * Check CLDB buffer against the PMIC's adev. If present, then we check
+ * the value of control_logic_type field and follow one of the
+ * following scenarios:
+ *
+ *	1. No CLDB - likely ACPI tables designed for ChromeOS. We
+ *	create platform devices for the GPIOs and OpRegion drivers.
+ *
+ *	2. CLDB, with control_logic_type = 2 - probably ACPI tables
+ *	made for Windows 2-in-1 platforms. Register pdevs for GPIO,
+ *	Clock and Regulator drivers to bind to.
+ *
+ *	3. Any other value in control_logic_type, we should never have
+ *	gotten to this point; fail probe and return.
+ *
+ * Return:
+ * * 1		Device intended for ChromeOS
+ * * 2		Device intended for Windows
+ * * -EINVAL	Where @adev has an object named CLDB but it does not conform to
+ *		our expectations
+ */
+static int skl_int3472_tps68470_calc_type(struct acpi_device *adev)
+{
+	struct int3472_cldb cldb = { 0 };
+	int ret;
+
+	/*
+	 * A CLDB buffer that exists, but which does not match our expectations
+	 * should trigger an error so we don't blindly continue.
+	 */
+	ret = skl_int3472_fill_cldb(adev, &cldb);
+	if (ret && ret != -ENODEV)
+		return ret;
+
+	if (ret)
+		return DESIGNED_FOR_CHROMEOS;
+
+	if (cldb.control_logic_type != 2)
+		return -EINVAL;
+
+	return DESIGNED_FOR_WINDOWS;
+}
+
+static int skl_int3472_tps68470_probe(struct i2c_client *client)
+{
+	struct acpi_device *adev = ACPI_COMPANION(&client->dev);
+	struct regmap *regmap;
+	int device_type;
+	int ret;
+
+	regmap = devm_regmap_init_i2c(client, &tps68470_regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&client->dev, "Failed to create regmap: %ld\n", PTR_ERR(regmap));
+		return PTR_ERR(regmap);
+	}
+
+	i2c_set_clientdata(client, regmap);
+
+	ret = tps68470_chip_init(&client->dev, regmap);
+	if (ret < 0) {
+		dev_err(&client->dev, "TPS68470 init error %d\n", ret);
+		return ret;
+	}
+
+	device_type = skl_int3472_tps68470_calc_type(adev);
+	switch (device_type) {
+	case DESIGNED_FOR_WINDOWS:
+		ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_NONE,
+					   tps68470_win, ARRAY_SIZE(tps68470_win),
+					   NULL, 0, NULL);
+		break;
+	case DESIGNED_FOR_CHROMEOS:
+		ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_NONE,
+					   tps68470_cros, ARRAY_SIZE(tps68470_cros),
+					   NULL, 0, NULL);
+		break;
+	default:
+		dev_err(&client->dev, "Failed to add MFD devices\n");
+		return device_type;
+	}
+
+	return ret;
+}
+
+static const struct acpi_device_id int3472_device_id[] = {
+	{ "INT3472", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, int3472_device_id);
+
+static struct i2c_driver int3472_tps68470 = {
+	.driver = {
+		.name = "int3472-tps68470",
+		.acpi_match_table = int3472_device_id,
+	},
+	.probe_new = skl_int3472_tps68470_probe,
+};
+module_i2c_driver(int3472_tps68470);
+
+MODULE_DESCRIPTION("Intel SkyLake INT3472 ACPI TPS68470 Device Driver");
+MODULE_AUTHOR("Daniel Scally <djrscally@gmail.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/pmc/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/pmc/core.c
@@ -958,7 +958,18 @@
 
 static inline u64 pmc_core_adjust_slp_s0_step(struct pmc_dev *pmcdev, u32 value)
 {
-	return (u64)value * pmcdev->map->slp_s0_res_counter_step;
+	/*
+	 * ADL PCH does not have the SLP_S0 counter and LPM Residency counters are
+	 * used as a workaround which uses 30.5 usec tick. All other client
+	 * programs have the legacy SLP_S0 residency counter that is using the 122
+	 * usec tick.
+	 */
+	const int lpm_adj_x2 = pmcdev->map->lpm_res_counter_step_x2;
+
+	if (pmcdev->map == &adl_reg_map)
+		return (u64)value * GET_X2_COUNTER((u64)lpm_adj_x2);
+	else
+		return (u64)value * pmcdev->map->slp_s0_res_counter_step;
 }
 
 static int set_etr3(struct pmc_dev *pmcdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/pmc/pltdrv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/pmc/pltdrv.c
@@ -18,6 +18,8 @@
 #include <asm/cpu_device_id.h>
 #include <asm/intel-family.h>
 
+#include <xen/xen.h>
+
 static void intel_pmc_core_release(struct device *dev)
 {
 	kfree(dev);
@@ -53,6 +55,13 @@
 	if (acpi_dev_present("INT33A1", NULL, -1))
 		return -ENODEV;
 
+	/*
+	 * Skip forcefully attaching the device for VMs. Make an exception for
+	 * Xen dom0, which does have full hardware access.
+	 */
+	if (cpu_feature_enabled(X86_FEATURE_HYPERVISOR) && !xen_initial_domain())
+		return -ENODEV;
+
 	if (!x86_match_cpu(intel_pmc_core_platform_ids))
 		return -ENODEV;
 
@@ -65,7 +74,7 @@
 
 	retval = platform_device_register(pmc_core_device);
 	if (retval)
-		kfree(pmc_core_device);
+		platform_device_put(pmc_core_device);
 
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/pmt/class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/pmt/class.c
@@ -9,6 +9,7 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
 #include <linux/module.h>
 #include <linux/mm.h>
 #include <linux/pci.h>
@@ -18,6 +19,7 @@
 #define PMT_XA_START		0
 #define PMT_XA_MAX		INT_MAX
 #define PMT_XA_LIMIT		XA_LIMIT(PMT_XA_START, PMT_XA_MAX)
+#define GUID_SPR_PUNIT		0x9956f43f
 
 /*
  * Early implementations of PMT on client platforms have some
@@ -41,6 +43,29 @@
 }
 EXPORT_SYMBOL_GPL(intel_pmt_is_early_client_hw);
 
+static inline int
+pmt_memcpy64_fromio(void *to, const u64 __iomem *from, size_t count)
+{
+	int i, remain;
+	u64 *buf = to;
+
+	if (!IS_ALIGNED((unsigned long)from, 8))
+		return -EFAULT;
+
+	for (i = 0; i < count/8; i++)
+		buf[i] = readq(&from[i]);
+
+	/* Copy any remaining bytes */
+	remain = count % 8;
+	if (remain) {
+		u64 tmp = readq(&from[i]);
+
+		memcpy(&buf[i], &tmp, remain);
+	}
+
+	return count;
+}
+
 /*
  * sysfs
  */
@@ -62,7 +87,11 @@
 	if (count > entry->size - off)
 		count = entry->size - off;
 
-	memcpy_fromio(buf, entry->base + off, count);
+	if (entry->guid == GUID_SPR_PUNIT)
+		/* PUNIT on SPR only supports aligned 64-bit read */
+		count = pmt_memcpy64_fromio(buf, entry->base + off, count);
+	else
+		memcpy_fromio(buf, entry->base + off, count);
 
 	return count;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/speed_select_if/isst_if_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/speed_select_if/isst_if_common.c
@@ -77,7 +77,7 @@
 static DEFINE_MUTEX(isst_hash_lock);
 
 static int isst_store_new_cmd(int cmd, u32 cpu, int mbox_cmd_type, u32 param,
-			      u32 data)
+			      u64 data)
 {
 	struct isst_cmd *sst_cmd;
 
@@ -277,39 +277,48 @@
 	return 0;
 }
 
+#define ISST_MAX_BUS_NUMBER	2
 
 struct isst_if_cpu_info {
 	/* For BUS 0 and BUS 1 only, which we need for PUNIT interface */
-	int bus_info[2];
-	struct pci_dev *pci_dev[2];
+	int bus_info[ISST_MAX_BUS_NUMBER];
+	struct pci_dev *pci_dev[ISST_MAX_BUS_NUMBER];
 	int punit_cpu_id;
 	int numa_node;
 };
 
+struct isst_if_pkg_info {
+	struct pci_dev *pci_dev[ISST_MAX_BUS_NUMBER];
+};
+
 static struct isst_if_cpu_info *isst_cpu_info;
-#define ISST_MAX_PCI_DOMAINS	8
+static struct isst_if_pkg_info *isst_pkg_info;
 
 static struct pci_dev *_isst_if_get_pci_dev(int cpu, int bus_no, int dev, int fn)
 {
 	struct pci_dev *matched_pci_dev = NULL;
 	struct pci_dev *pci_dev = NULL;
-	int no_matches = 0;
-	int i, bus_number;
+	struct pci_dev *_pci_dev = NULL;
+	int no_matches = 0, pkg_id;
+	int bus_number;
+
+	if (bus_no < 0 || bus_no >= ISST_MAX_BUS_NUMBER || cpu < 0 ||
+	    cpu >= nr_cpu_ids || cpu >= num_possible_cpus())
+		return NULL;
 
-	if (bus_no < 0 || bus_no > 1 || cpu < 0 || cpu >= nr_cpu_ids ||
-	    cpu >= num_possible_cpus())
+	pkg_id = topology_logical_package_id(cpu);
+	if (pkg_id >= topology_max_packages())
 		return NULL;
 
 	bus_number = isst_cpu_info[cpu].bus_info[bus_no];
 	if (bus_number < 0)
 		return NULL;
 
-	for (i = 0; i < ISST_MAX_PCI_DOMAINS; ++i) {
-		struct pci_dev *_pci_dev;
+	for_each_pci_dev(_pci_dev) {
 		int node;
 
-		_pci_dev = pci_get_domain_bus_and_slot(i, bus_number, PCI_DEVFN(dev, fn));
-		if (!_pci_dev)
+		if (_pci_dev->bus->number != bus_number ||
+		    _pci_dev->devfn != PCI_DEVFN(dev, fn))
 			continue;
 
 		++no_matches;
@@ -324,6 +333,8 @@
 		}
 
 		if (node == isst_cpu_info[cpu].numa_node) {
+			isst_pkg_info[pkg_id].pci_dev[bus_no] = _pci_dev;
+
 			pci_dev = _pci_dev;
 			break;
 		}
@@ -342,6 +353,10 @@
 	if (!pci_dev && no_matches == 1)
 		pci_dev = matched_pci_dev;
 
+	/* Return pci_dev pointer for any matched CPU in the package */
+	if (!pci_dev)
+		pci_dev = isst_pkg_info[pkg_id].pci_dev[bus_no];
+
 	return pci_dev;
 }
 
@@ -361,8 +376,8 @@
 {
 	struct pci_dev *pci_dev;
 
-	if (bus_no < 0 || bus_no > 1 || cpu < 0 || cpu >= nr_cpu_ids ||
-	    cpu >= num_possible_cpus())
+	if (bus_no < 0 || bus_no >= ISST_MAX_BUS_NUMBER  || cpu < 0 ||
+	    cpu >= nr_cpu_ids || cpu >= num_possible_cpus())
 		return NULL;
 
 	pci_dev = isst_cpu_info[cpu].pci_dev[bus_no];
@@ -417,10 +432,19 @@
 	if (!isst_cpu_info)
 		return -ENOMEM;
 
+	isst_pkg_info = kcalloc(topology_max_packages(),
+				sizeof(*isst_pkg_info),
+				GFP_KERNEL);
+	if (!isst_pkg_info) {
+		kfree(isst_cpu_info);
+		return -ENOMEM;
+	}
+
 	ret = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN,
 				"platform/x86/isst-if:online",
 				isst_if_cpu_online, NULL);
 	if (ret < 0) {
+		kfree(isst_pkg_info);
 		kfree(isst_cpu_info);
 		return ret;
 	}
@@ -433,6 +457,7 @@
 static void isst_if_cpu_info_exit(void)
 {
 	cpuhp_remove_state(isst_if_online_id);
+	kfree(isst_pkg_info);
 	kfree(isst_cpu_info);
 };
 
@@ -596,7 +621,10 @@
 	return ret;
 }
 
-static DEFINE_MUTEX(punit_misc_dev_lock);
+/* Lock to prevent module registration when already opened by user space */
+static DEFINE_MUTEX(punit_misc_dev_open_lock);
+/* Lock to allow one share misc device for all ISST interace */
+static DEFINE_MUTEX(punit_misc_dev_reg_lock);
 static int misc_usage_count;
 static int misc_device_ret;
 static int misc_device_open;
@@ -606,7 +634,7 @@
 	int i, ret = 0;
 
 	/* Fail open, if a module is going away */
-	mutex_lock(&punit_misc_dev_lock);
+	mutex_lock(&punit_misc_dev_open_lock);
 	for (i = 0; i < ISST_IF_DEV_MAX; ++i) {
 		struct isst_if_cmd_cb *cb = &punit_callbacks[i];
 
@@ -628,7 +656,7 @@
 	} else {
 		misc_device_open++;
 	}
-	mutex_unlock(&punit_misc_dev_lock);
+	mutex_unlock(&punit_misc_dev_open_lock);
 
 	return ret;
 }
@@ -637,7 +665,7 @@
 {
 	int i;
 
-	mutex_lock(&punit_misc_dev_lock);
+	mutex_lock(&punit_misc_dev_open_lock);
 	misc_device_open--;
 	for (i = 0; i < ISST_IF_DEV_MAX; ++i) {
 		struct isst_if_cmd_cb *cb = &punit_callbacks[i];
@@ -645,7 +673,7 @@
 		if (cb->registered)
 			module_put(cb->owner);
 	}
-	mutex_unlock(&punit_misc_dev_lock);
+	mutex_unlock(&punit_misc_dev_open_lock);
 
 	return 0;
 }
@@ -662,6 +690,43 @@
 	.fops		= &isst_if_char_driver_ops,
 };
 
+static int isst_misc_reg(void)
+{
+	mutex_lock(&punit_misc_dev_reg_lock);
+	if (misc_device_ret)
+		goto unlock_exit;
+
+	if (!misc_usage_count) {
+		misc_device_ret = isst_if_cpu_info_init();
+		if (misc_device_ret)
+			goto unlock_exit;
+
+		misc_device_ret = misc_register(&isst_if_char_driver);
+		if (misc_device_ret) {
+			isst_if_cpu_info_exit();
+			goto unlock_exit;
+		}
+	}
+	misc_usage_count++;
+
+unlock_exit:
+	mutex_unlock(&punit_misc_dev_reg_lock);
+
+	return misc_device_ret;
+}
+
+static void isst_misc_unreg(void)
+{
+	mutex_lock(&punit_misc_dev_reg_lock);
+	if (misc_usage_count)
+		misc_usage_count--;
+	if (!misc_usage_count && !misc_device_ret) {
+		misc_deregister(&isst_if_char_driver);
+		isst_if_cpu_info_exit();
+	}
+	mutex_unlock(&punit_misc_dev_reg_lock);
+}
+
 /**
  * isst_if_cdev_register() - Register callback for IOCTL
  * @device_type: The device type this callback handling.
@@ -679,38 +744,31 @@
  */
 int isst_if_cdev_register(int device_type, struct isst_if_cmd_cb *cb)
 {
-	if (misc_device_ret)
-		return misc_device_ret;
+	int ret;
 
 	if (device_type >= ISST_IF_DEV_MAX)
 		return -EINVAL;
 
-	mutex_lock(&punit_misc_dev_lock);
+	mutex_lock(&punit_misc_dev_open_lock);
+	/* Device is already open, we don't want to add new callbacks */
 	if (misc_device_open) {
-		mutex_unlock(&punit_misc_dev_lock);
+		mutex_unlock(&punit_misc_dev_open_lock);
 		return -EAGAIN;
 	}
-	if (!misc_usage_count) {
-		int ret;
-
-		misc_device_ret = misc_register(&isst_if_char_driver);
-		if (misc_device_ret)
-			goto unlock_exit;
-
-		ret = isst_if_cpu_info_init();
-		if (ret) {
-			misc_deregister(&isst_if_char_driver);
-			misc_device_ret = ret;
-			goto unlock_exit;
-		}
-	}
 	memcpy(&punit_callbacks[device_type], cb, sizeof(*cb));
 	punit_callbacks[device_type].registered = 1;
-	misc_usage_count++;
-unlock_exit:
-	mutex_unlock(&punit_misc_dev_lock);
+	mutex_unlock(&punit_misc_dev_open_lock);
 
-	return misc_device_ret;
+	ret = isst_misc_reg();
+	if (ret) {
+		/*
+		 * No need of mutex as the misc device register failed
+		 * as no one can open device yet. Hence no contention.
+		 */
+		punit_callbacks[device_type].registered = 0;
+		return ret;
+	}
+	return 0;
 }
 EXPORT_SYMBOL_GPL(isst_if_cdev_register);
 
@@ -725,16 +783,12 @@
  */
 void isst_if_cdev_unregister(int device_type)
 {
-	mutex_lock(&punit_misc_dev_lock);
-	misc_usage_count--;
+	isst_misc_unreg();
+	mutex_lock(&punit_misc_dev_open_lock);
 	punit_callbacks[device_type].registered = 0;
 	if (device_type == ISST_IF_DEV_MBOX)
 		isst_delete_hash();
-	if (!misc_usage_count && !misc_device_ret) {
-		misc_deregister(&isst_if_char_driver);
-		isst_if_cpu_info_exit();
-	}
-	mutex_unlock(&punit_misc_dev_lock);
+	mutex_unlock(&punit_misc_dev_open_lock);
 }
 EXPORT_SYMBOL_GPL(isst_if_cdev_unregister);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/telemetry/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/telemetry/core.c
@@ -102,7 +102,7 @@
 /**
  * telemetry_update_events() - Update telemetry Configuration
  * @pss_evtconfig: PSS related config. No change if num_evts = 0.
- * @pss_evtconfig: IOSS related config. No change if num_evts = 0.
+ * @ioss_evtconfig: IOSS related config. No change if num_evts = 0.
  *
  * This API updates the IOSS & PSS Telemetry configuration. Old config
  * is overwritten. Call telemetry_reset_events when logging is over
@@ -176,7 +176,7 @@
 /**
  * telemetry_get_eventconfig() - Returns the pss and ioss events enabled
  * @pss_evtconfig: Pointer to PSS related configuration.
- * @pss_evtconfig: Pointer to IOSS related configuration.
+ * @ioss_evtconfig: Pointer to IOSS related configuration.
  * @pss_len:	   Number of u32 elements allocated for pss_evtconfig array
  * @ioss_len:	   Number of u32 elements allocated for ioss_evtconfig array
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/uncore-frequency.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/uncore-frequency.c
@@ -378,6 +378,7 @@
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_X,	NULL),
 	X86_MATCH_INTEL_FAM6_MODEL(ICELAKE_D,	NULL),
 	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X, NULL),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X, NULL),
 	{}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel/vbtn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel/vbtn.c
@@ -73,10 +73,10 @@
 	bool wakeup_mode;
 };
 
-static void detect_tablet_mode(struct platform_device *device)
+static void detect_tablet_mode(struct device *dev)
 {
-	struct intel_vbtn_priv *priv = dev_get_drvdata(&device->dev);
-	acpi_handle handle = ACPI_HANDLE(&device->dev);
+	struct intel_vbtn_priv *priv = dev_get_drvdata(dev);
+	acpi_handle handle = ACPI_HANDLE(dev);
 	unsigned long long vgbs;
 	acpi_status status;
 	int m;
@@ -89,6 +89,8 @@
 	input_report_switch(priv->switches_dev, SW_TABLET_MODE, m);
 	m = (vgbs & VGBS_DOCK_MODE_FLAG) ? 1 : 0;
 	input_report_switch(priv->switches_dev, SW_DOCK, m);
+
+	input_sync(priv->switches_dev);
 }
 
 /*
@@ -134,8 +136,6 @@
 	priv->switches_dev->id.bustype = BUS_HOST;
 
 	if (priv->has_switches) {
-		detect_tablet_mode(device);
-
 		ret = input_register_device(priv->switches_dev);
 		if (ret)
 			return ret;
@@ -314,6 +314,9 @@
 		if (ACPI_FAILURE(status))
 			dev_err(&device->dev, "Error VBDL failed with ACPI status %d\n", status);
 	}
+	// Check switches after buttons since VBDL may have side effects.
+	if (has_switches)
+		detect_tablet_mode(&device->dev);
 
 	device_init_wakeup(&device->dev, true);
 	/*
@@ -358,7 +361,13 @@
 
 static int intel_vbtn_pm_resume(struct device *dev)
 {
+	struct intel_vbtn_priv *priv = dev_get_drvdata(dev);
+
 	intel_vbtn_pm_complete(dev);
+
+	if (priv->has_switches)
+		detect_tablet_mode(dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel_ips.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel_ips.c
@@ -1432,6 +1432,14 @@
 			DMI_MATCH(DMI_PRODUCT_NAME, "HP ProBook"),
 		},
 	},
+	{
+		.callback = ips_blacklist_callback,
+		.ident = "G60JX",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK Computer Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "G60JX"),
+		},
+	},
 	{ }	/* terminating entry */
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel_scu_ipc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel_scu_ipc.c
@@ -19,6 +19,7 @@
 #include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/slab.h>
 
@@ -232,19 +233,15 @@
 /* Wait till scu status is busy */
 static inline int busy_loop(struct intel_scu_ipc_dev *scu)
 {
-	unsigned long end = jiffies + IPC_TIMEOUT;
-
-	do {
-		u32 status;
-
-		status = ipc_read_status(scu);
-		if (!(status & IPC_STATUS_BUSY))
-			return (status & IPC_STATUS_ERR) ? -EIO : 0;
+	u8 status;
+	int err;
 
-		usleep_range(50, 100);
-	} while (time_before(jiffies, end));
+	err = readx_poll_timeout(ipc_read_status, scu, status, !(status & IPC_STATUS_BUSY),
+				 100, jiffies_to_usecs(IPC_TIMEOUT));
+	if (err)
+		return err;
 
-	return -ETIMEDOUT;
+	return (status & IPC_STATUS_ERR) ? -EIO : 0;
 }
 
 /* Wait till ipc ioc interrupt is received or timeout in 10 HZ */
@@ -252,10 +249,12 @@
 {
 	int status;
 
-	if (!wait_for_completion_timeout(&scu->cmd_complete, IPC_TIMEOUT))
-		return -ETIMEDOUT;
+	wait_for_completion_timeout(&scu->cmd_complete, IPC_TIMEOUT);
 
 	status = ipc_read_status(scu);
+	if (status & IPC_STATUS_BUSY)
+		return -ETIMEDOUT;
+
 	if (status & IPC_STATUS_ERR)
 		return -EIO;
 
@@ -267,6 +266,24 @@
 	return scu->irq > 0 ? ipc_wait_for_interrupt(scu) : busy_loop(scu);
 }
 
+static struct intel_scu_ipc_dev *intel_scu_ipc_get(struct intel_scu_ipc_dev *scu)
+{
+	u8 status;
+
+	if (!scu)
+		scu = ipcdev;
+	if (!scu)
+		return ERR_PTR(-ENODEV);
+
+	status = ipc_read_status(scu);
+	if (status & IPC_STATUS_BUSY) {
+		dev_dbg(&scu->dev, "device is busy\n");
+		return ERR_PTR(-EBUSY);
+	}
+
+	return scu;
+}
+
 /* Read/Write power control(PMIC in Langwell, MSIC in PenWell) registers */
 static int pwr_reg_rdwr(struct intel_scu_ipc_dev *scu, u16 *addr, u8 *data,
 			u32 count, u32 op, u32 id)
@@ -280,11 +297,10 @@
 	memset(cbuf, 0, sizeof(cbuf));
 
 	mutex_lock(&ipclock);
-	if (!scu)
-		scu = ipcdev;
-	if (!scu) {
+	scu = intel_scu_ipc_get(scu);
+	if (IS_ERR(scu)) {
 		mutex_unlock(&ipclock);
-		return -ENODEV;
+		return PTR_ERR(scu);
 	}
 
 	for (nc = 0; nc < count; nc++, offset += 2) {
@@ -439,13 +455,12 @@
 	int err;
 
 	mutex_lock(&ipclock);
-	if (!scu)
-		scu = ipcdev;
-	if (!scu) {
+	scu = intel_scu_ipc_get(scu);
+	if (IS_ERR(scu)) {
 		mutex_unlock(&ipclock);
-		return -ENODEV;
+		return PTR_ERR(scu);
 	}
-	scu = ipcdev;
+
 	cmdval = sub << 12 | cmd;
 	ipc_command(scu, cmdval);
 	err = intel_scu_ipc_check_status(scu);
@@ -485,11 +500,10 @@
 		return -EINVAL;
 
 	mutex_lock(&ipclock);
-	if (!scu)
-		scu = ipcdev;
-	if (!scu) {
+	scu = intel_scu_ipc_get(scu);
+	if (IS_ERR(scu)) {
 		mutex_unlock(&ipclock);
-		return -ENODEV;
+		return PTR_ERR(scu);
 	}
 
 	memcpy(inbuf, in, inlen);
@@ -583,7 +597,6 @@
 	scu->dev.parent = parent;
 	scu->dev.class = &intel_scu_ipc_class;
 	scu->dev.release = intel_scu_ipc_release;
-	dev_set_name(&scu->dev, "intel_scu_ipc");
 
 	if (!request_mem_region(scu_data->mem.start, resource_size(&scu_data->mem),
 				"intel_scu_ipc")) {
@@ -612,6 +625,7 @@
 	 * After this point intel_scu_ipc_release() takes care of
 	 * releasing the SCU IPC resources once refcount drops to zero.
 	 */
+	dev_set_name(&scu->dev, "intel_scu_ipc");
 	err = device_register(&scu->dev);
 	if (err) {
 		put_device(&scu->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/intel_scu_pcidrv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/intel_scu_pcidrv.c
@@ -34,6 +34,7 @@
 
 static const struct pci_device_id pci_ids[] = {
 	{ PCI_VDEVICE(INTEL, 0x080e) },
+	{ PCI_VDEVICE(INTEL, 0x082a) },
 	{ PCI_VDEVICE(INTEL, 0x08ea) },
 	{ PCI_VDEVICE(INTEL, 0x0a94) },
 	{ PCI_VDEVICE(INTEL, 0x11a0) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/lg-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/lg-laptop.c
@@ -37,8 +37,6 @@
 #define WMI_METHOD_WMBB "2B4F501A-BD3C-4394-8DCF-00A7D2BC8210"
 #define WMI_EVENT_GUID  WMI_EVENT_GUID0
 
-#define WMAB_METHOD     "\\XINI.WMAB"
-#define WMBB_METHOD     "\\XINI.WMBB"
 #define SB_GGOV_METHOD  "\\_SB.GGOV"
 #define GOV_TLED        0x2020008
 #define WM_GET          1
@@ -73,7 +71,7 @@
 
 static int battery_limit_use_wmbb;
 static struct led_classdev kbd_backlight;
-static enum led_brightness get_kbd_backlight_level(void);
+static enum led_brightness get_kbd_backlight_level(struct device *dev);
 
 static const struct key_entry wmi_keymap[] = {
 	{KE_KEY, 0x70, {KEY_F15} },	 /* LG control panel (F1) */
@@ -83,7 +81,6 @@
 					  * this key both sends an event and
 					  * changes backlight level.
 					  */
-	{KE_KEY, 0x80, {KEY_RFKILL} },
 	{KE_END, 0}
 };
 
@@ -127,11 +124,10 @@
 	return res;
 }
 
-static union acpi_object *lg_wmab(u32 method, u32 arg1, u32 arg2)
+static union acpi_object *lg_wmab(struct device *dev, u32 method, u32 arg1, u32 arg2)
 {
 	union acpi_object args[3];
 	acpi_status status;
-	acpi_handle handle;
 	struct acpi_object_list arg;
 	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
 
@@ -142,29 +138,22 @@
 	args[2].type = ACPI_TYPE_INTEGER;
 	args[2].integer.value = arg2;
 
-	status = acpi_get_handle(NULL, (acpi_string) WMAB_METHOD, &handle);
-	if (ACPI_FAILURE(status)) {
-		pr_err("Cannot get handle");
-		return NULL;
-	}
-
 	arg.count = 3;
 	arg.pointer = args;
 
-	status = acpi_evaluate_object(handle, NULL, &arg, &buffer);
+	status = acpi_evaluate_object(ACPI_HANDLE(dev), "WMAB", &arg, &buffer);
 	if (ACPI_FAILURE(status)) {
-		acpi_handle_err(handle, "WMAB: call failed.\n");
+		dev_err(dev, "WMAB: call failed.\n");
 		return NULL;
 	}
 
 	return buffer.pointer;
 }
 
-static union acpi_object *lg_wmbb(u32 method_id, u32 arg1, u32 arg2)
+static union acpi_object *lg_wmbb(struct device *dev, u32 method_id, u32 arg1, u32 arg2)
 {
 	union acpi_object args[3];
 	acpi_status status;
-	acpi_handle handle;
 	struct acpi_object_list arg;
 	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
 	u8 buf[32];
@@ -180,18 +169,12 @@
 	args[2].buffer.length = 32;
 	args[2].buffer.pointer = buf;
 
-	status = acpi_get_handle(NULL, (acpi_string)WMBB_METHOD, &handle);
-	if (ACPI_FAILURE(status)) {
-		pr_err("Cannot get handle");
-		return NULL;
-	}
-
 	arg.count = 3;
 	arg.pointer = args;
 
-	status = acpi_evaluate_object(handle, NULL, &arg, &buffer);
+	status = acpi_evaluate_object(ACPI_HANDLE(dev), "WMBB", &arg, &buffer);
 	if (ACPI_FAILURE(status)) {
-		acpi_handle_err(handle, "WMAB: call failed.\n");
+		dev_err(dev, "WMBB: call failed.\n");
 		return NULL;
 	}
 
@@ -222,7 +205,7 @@
 
 		if (eventcode == 0x10000000) {
 			led_classdev_notify_brightness_hw_changed(
-				&kbd_backlight, get_kbd_backlight_level());
+				&kbd_backlight, get_kbd_backlight_level(kbd_backlight.dev->parent));
 		} else {
 			key = sparse_keymap_entry_from_scancode(
 				wmi_input_dev, eventcode);
@@ -271,14 +254,7 @@
 
 static void acpi_notify(struct acpi_device *device, u32 event)
 {
-	struct key_entry *key;
-
 	acpi_handle_debug(device->handle, "notify: %d\n", event);
-	if (inited & INIT_SPARSE_KEYMAP) {
-		key = sparse_keymap_entry_from_scancode(wmi_input_dev, 0x80);
-		if (key && key->type == KE_KEY)
-			sparse_keymap_report_entry(wmi_input_dev, key, 1, true);
-	}
 }
 
 static ssize_t fan_mode_store(struct device *dev,
@@ -294,7 +270,7 @@
 	if (ret)
 		return ret;
 
-	r = lg_wmab(WM_FAN_MODE, WM_GET, 0);
+	r = lg_wmab(dev, WM_FAN_MODE, WM_GET, 0);
 	if (!r)
 		return -EIO;
 
@@ -305,9 +281,9 @@
 
 	m = r->integer.value;
 	kfree(r);
-	r = lg_wmab(WM_FAN_MODE, WM_SET, (m & 0xffffff0f) | (value << 4));
+	r = lg_wmab(dev, WM_FAN_MODE, WM_SET, (m & 0xffffff0f) | (value << 4));
 	kfree(r);
-	r = lg_wmab(WM_FAN_MODE, WM_SET, (m & 0xfffffff0) | value);
+	r = lg_wmab(dev, WM_FAN_MODE, WM_SET, (m & 0xfffffff0) | value);
 	kfree(r);
 
 	return count;
@@ -319,7 +295,7 @@
 	unsigned int status;
 	union acpi_object *r;
 
-	r = lg_wmab(WM_FAN_MODE, WM_GET, 0);
+	r = lg_wmab(dev, WM_FAN_MODE, WM_GET, 0);
 	if (!r)
 		return -EIO;
 
@@ -346,7 +322,7 @@
 	if (ret)
 		return ret;
 
-	r = lg_wmbb(WMBB_USB_CHARGE, WM_SET, value);
+	r = lg_wmbb(dev, WMBB_USB_CHARGE, WM_SET, value);
 	if (!r)
 		return -EIO;
 
@@ -360,7 +336,7 @@
 	unsigned int status;
 	union acpi_object *r;
 
-	r = lg_wmbb(WMBB_USB_CHARGE, WM_GET, 0);
+	r = lg_wmbb(dev, WMBB_USB_CHARGE, WM_GET, 0);
 	if (!r)
 		return -EIO;
 
@@ -388,7 +364,7 @@
 	if (ret)
 		return ret;
 
-	r = lg_wmab(WM_READER_MODE, WM_SET, value);
+	r = lg_wmab(dev, WM_READER_MODE, WM_SET, value);
 	if (!r)
 		return -EIO;
 
@@ -402,7 +378,7 @@
 	unsigned int status;
 	union acpi_object *r;
 
-	r = lg_wmab(WM_READER_MODE, WM_GET, 0);
+	r = lg_wmab(dev, WM_READER_MODE, WM_GET, 0);
 	if (!r)
 		return -EIO;
 
@@ -430,7 +406,7 @@
 	if (ret)
 		return ret;
 
-	r = lg_wmab(WM_FN_LOCK, WM_SET, value);
+	r = lg_wmab(dev, WM_FN_LOCK, WM_SET, value);
 	if (!r)
 		return -EIO;
 
@@ -444,7 +420,7 @@
 	unsigned int status;
 	union acpi_object *r;
 
-	r = lg_wmab(WM_FN_LOCK, WM_GET, 0);
+	r = lg_wmab(dev, WM_FN_LOCK, WM_GET, 0);
 	if (!r)
 		return -EIO;
 
@@ -474,9 +450,9 @@
 		union acpi_object *r;
 
 		if (battery_limit_use_wmbb)
-			r = lg_wmbb(WMBB_BATT_LIMIT, WM_SET, value);
+			r = lg_wmbb(&pf_device->dev, WMBB_BATT_LIMIT, WM_SET, value);
 		else
-			r = lg_wmab(WM_BATT_LIMIT, WM_SET, value);
+			r = lg_wmab(&pf_device->dev, WM_BATT_LIMIT, WM_SET, value);
 		if (!r)
 			return -EIO;
 
@@ -495,7 +471,7 @@
 	union acpi_object *r;
 
 	if (battery_limit_use_wmbb) {
-		r = lg_wmbb(WMBB_BATT_LIMIT, WM_GET, 0);
+		r = lg_wmbb(&pf_device->dev, WMBB_BATT_LIMIT, WM_GET, 0);
 		if (!r)
 			return -EIO;
 
@@ -506,7 +482,7 @@
 
 		status = r->buffer.pointer[0x10];
 	} else {
-		r = lg_wmab(WM_BATT_LIMIT, WM_GET, 0);
+		r = lg_wmab(&pf_device->dev, WM_BATT_LIMIT, WM_GET, 0);
 		if (!r)
 			return -EIO;
 
@@ -548,7 +524,7 @@
 {
 	union acpi_object *r;
 
-	r = lg_wmab(WM_TLED, WM_SET, brightness > LED_OFF);
+	r = lg_wmab(cdev->dev->parent, WM_TLED, WM_SET, brightness > LED_OFF);
 	kfree(r);
 }
 
@@ -570,16 +546,16 @@
 		val = 0;
 	if (brightness >= LED_FULL)
 		val = 0x24;
-	r = lg_wmab(WM_KEY_LIGHT, WM_SET, val);
+	r = lg_wmab(cdev->dev->parent, WM_KEY_LIGHT, WM_SET, val);
 	kfree(r);
 }
 
-static enum led_brightness get_kbd_backlight_level(void)
+static enum led_brightness get_kbd_backlight_level(struct device *dev)
 {
 	union acpi_object *r;
 	int val;
 
-	r = lg_wmab(WM_KEY_LIGHT, WM_GET, 0);
+	r = lg_wmab(dev, WM_KEY_LIGHT, WM_GET, 0);
 
 	if (!r)
 		return LED_OFF;
@@ -607,7 +583,7 @@
 
 static enum led_brightness kbd_backlight_get(struct led_classdev *cdev)
 {
-	return get_kbd_backlight_level();
+	return get_kbd_backlight_level(cdev->dev->parent);
 }
 
 static LED_DEVICE(kbd_backlight, 255, LED_BRIGHT_HW_CHANGED);
@@ -634,6 +610,11 @@
 
 static int acpi_add(struct acpi_device *device)
 {
+	struct platform_device_info pdev_info = {
+		.fwnode = acpi_fwnode_handle(device),
+		.name = PLATFORM_NAME,
+		.id = PLATFORM_DEVID_NONE,
+	};
 	int ret;
 	const char *product;
 	int year = 2017;
@@ -645,9 +626,7 @@
 	if (ret)
 		return ret;
 
-	pf_device = platform_device_register_simple(PLATFORM_NAME,
-						    PLATFORM_DEVID_NONE,
-						    NULL, 0);
+	pf_device = platform_device_register_full(&pdev_info);
 	if (IS_ERR(pf_device)) {
 		ret = PTR_ERR(pf_device);
 		pf_device = NULL;
@@ -686,7 +665,7 @@
 		default:
 			year = 2019;
 		}
-	pr_info("product: %s  year: %d\n", product, year);
+	pr_info("product: %s  year: %d\n", product ?: "unknown", year);
 
 	if (year >= 2019)
 		battery_limit_use_wmbb = 1;
@@ -726,7 +705,7 @@
 }
 
 static const struct acpi_device_id device_ids[] = {
-	{"LGEX0815", 0},
+	{"LGEX0820", 0},
 	{"", 0}
 };
 MODULE_DEVICE_TABLE(acpi, device_ids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/msi-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/msi-laptop.c
@@ -210,7 +210,7 @@
 		return -EINVAL;
 
 	if (quirks->ec_read_only)
-		return -EOPNOTSUPP;
+		return 0;
 
 	/* read current device state */
 	result = ec_read(MSI_STANDARD_EC_COMMAND_ADDRESS, &rdata);
@@ -596,11 +596,10 @@
 	{
 		.ident = "MSI S270",
 		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "MICRO-STAR INT'L CO.,LTD"),
+			DMI_MATCH(DMI_SYS_VENDOR, "MICRO-STAR INT"),
 			DMI_MATCH(DMI_PRODUCT_NAME, "MS-1013"),
 			DMI_MATCH(DMI_PRODUCT_VERSION, "0131"),
-			DMI_MATCH(DMI_CHASSIS_VENDOR,
-				  "MICRO-STAR INT'L CO.,LTD")
+			DMI_MATCH(DMI_CHASSIS_VENDOR, "MICRO-STAR INT")
 		},
 		.driver_data = &quirk_old_ec_model,
 		.callback = dmi_check_cb
@@ -633,8 +632,7 @@
 			DMI_MATCH(DMI_SYS_VENDOR, "NOTEBOOK"),
 			DMI_MATCH(DMI_PRODUCT_NAME, "SAM2000"),
 			DMI_MATCH(DMI_PRODUCT_VERSION, "0131"),
-			DMI_MATCH(DMI_CHASSIS_VENDOR,
-				  "MICRO-STAR INT'L CO.,LTD")
+			DMI_MATCH(DMI_CHASSIS_VENDOR, "MICRO-STAR INT")
 		},
 		.driver_data = &quirk_old_ec_model,
 		.callback = dmi_check_cb
@@ -843,15 +841,15 @@
 static void msi_init_rfkill(struct work_struct *ignored)
 {
 	if (rfk_wlan) {
-		rfkill_set_sw_state(rfk_wlan, !wlan_s);
+		msi_rfkill_set_state(rfk_wlan, !wlan_s);
 		rfkill_wlan_set(NULL, !wlan_s);
 	}
 	if (rfk_bluetooth) {
-		rfkill_set_sw_state(rfk_bluetooth, !bluetooth_s);
+		msi_rfkill_set_state(rfk_bluetooth, !bluetooth_s);
 		rfkill_bluetooth_set(NULL, !bluetooth_s);
 	}
 	if (rfk_threeg) {
-		rfkill_set_sw_state(rfk_threeg, !threeg_s);
+		msi_rfkill_set_state(rfk_threeg, !threeg_s);
 		rfkill_threeg_set(NULL, !threeg_s);
 	}
 }
@@ -1048,8 +1046,7 @@
 		return -EINVAL;
 
 	/* Register backlight stuff */
-
-	if (quirks->old_ec_model ||
+	if (quirks->old_ec_model &&
 	    acpi_video_get_backlight_type() == acpi_backlight_vendor) {
 		struct backlight_properties props;
 		memset(&props, 0, sizeof(struct backlight_properties));
@@ -1117,6 +1114,8 @@
 fail_create_group:
 	if (quirks->load_scm_model) {
 		i8042_remove_filter(msi_laptop_i8042_filter);
+		cancel_delayed_work_sync(&msi_touchpad_dwork);
+		input_unregister_device(msi_laptop_input_dev);
 		cancel_delayed_work_sync(&msi_rfkill_dwork);
 		cancel_work_sync(&msi_rfkill_work);
 		rfkill_cleanup();
@@ -1137,6 +1136,7 @@
 {
 	if (quirks->load_scm_model) {
 		i8042_remove_filter(msi_laptop_i8042_filter);
+		cancel_delayed_work_sync(&msi_touchpad_dwork);
 		input_unregister_device(msi_laptop_input_dev);
 		cancel_delayed_work_sync(&msi_rfkill_dwork);
 		cancel_work_sync(&msi_rfkill_work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/mxm-wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/mxm-wmi.c
@@ -35,13 +35,11 @@
 		.xarg = 1,
 	};
 	struct acpi_buffer input = { (acpi_size)sizeof(args), &args };
-	struct acpi_buffer output = { ACPI_ALLOCATE_BUFFER, NULL };
 	acpi_status status;
 
 	printk("calling mux switch %d\n", adapter);
 
-	status = wmi_evaluate_method(MXM_WMMX_GUID, 0x0, adapter, &input,
-				     &output);
+	status = wmi_evaluate_method(MXM_WMMX_GUID, 0x0, adapter, &input, NULL);
 
 	if (ACPI_FAILURE(status))
 		return status;
@@ -60,13 +58,11 @@
 		.xarg = 1,
 	};
 	struct acpi_buffer input = { (acpi_size)sizeof(args), &args };
-	struct acpi_buffer output = { ACPI_ALLOCATE_BUFFER, NULL };
 	acpi_status status;
 
 	printk("calling mux switch %d\n", adapter);
 
-	status = wmi_evaluate_method(MXM_WMMX_GUID, 0x0, adapter, &input,
-				     &output);
+	status = wmi_evaluate_method(MXM_WMMX_GUID, 0x0, adapter, &input, NULL);
 
 	if (ACPI_FAILURE(status))
 		return status;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/nvidia-wmi-ec-backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/nvidia-wmi-ec-backlight.c
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020, NVIDIA CORPORATION.  All rights reserved.
+ */
+
+#include <linux/acpi.h>
+#include <linux/backlight.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/wmi.h>
+
+/**
+ * enum wmi_brightness_method - WMI method IDs
+ * @WMI_BRIGHTNESS_METHOD_LEVEL:  Get/Set EC brightness level status
+ * @WMI_BRIGHTNESS_METHOD_SOURCE: Get/Set EC Brightness Source
+ */
+enum wmi_brightness_method {
+	WMI_BRIGHTNESS_METHOD_LEVEL = 1,
+	WMI_BRIGHTNESS_METHOD_SOURCE = 2,
+	WMI_BRIGHTNESS_METHOD_MAX
+};
+
+/**
+ * enum wmi_brightness_mode - Operation mode for WMI-wrapped method
+ * @WMI_BRIGHTNESS_MODE_GET:            Get the current brightness level/source.
+ * @WMI_BRIGHTNESS_MODE_SET:            Set the brightness level.
+ * @WMI_BRIGHTNESS_MODE_GET_MAX_LEVEL:  Get the maximum brightness level. This
+ *                                      is only valid when the WMI method is
+ *                                      %WMI_BRIGHTNESS_METHOD_LEVEL.
+ */
+enum wmi_brightness_mode {
+	WMI_BRIGHTNESS_MODE_GET = 0,
+	WMI_BRIGHTNESS_MODE_SET = 1,
+	WMI_BRIGHTNESS_MODE_GET_MAX_LEVEL = 2,
+	WMI_BRIGHTNESS_MODE_MAX
+};
+
+/**
+ * enum wmi_brightness_source - Backlight brightness control source selection
+ * @WMI_BRIGHTNESS_SOURCE_GPU: Backlight brightness is controlled by the GPU.
+ * @WMI_BRIGHTNESS_SOURCE_EC:  Backlight brightness is controlled by the
+ *                             system's Embedded Controller (EC).
+ * @WMI_BRIGHTNESS_SOURCE_AUX: Backlight brightness is controlled over the
+ *                             DisplayPort AUX channel.
+ */
+enum wmi_brightness_source {
+	WMI_BRIGHTNESS_SOURCE_GPU = 1,
+	WMI_BRIGHTNESS_SOURCE_EC = 2,
+	WMI_BRIGHTNESS_SOURCE_AUX = 3,
+	WMI_BRIGHTNESS_SOURCE_MAX
+};
+
+/**
+ * struct wmi_brightness_args - arguments for the WMI-wrapped ACPI method
+ * @mode:    Pass in an &enum wmi_brightness_mode value to select between
+ *           getting or setting a value.
+ * @val:     In parameter for value to set when using %WMI_BRIGHTNESS_MODE_SET
+ *           mode. Not used in conjunction with %WMI_BRIGHTNESS_MODE_GET or
+ *           %WMI_BRIGHTNESS_MODE_GET_MAX_LEVEL mode.
+ * @ret:     Out parameter returning retrieved value when operating in
+ *           %WMI_BRIGHTNESS_MODE_GET or %WMI_BRIGHTNESS_MODE_GET_MAX_LEVEL
+ *           mode. Not used in %WMI_BRIGHTNESS_MODE_SET mode.
+ * @ignored: Padding; not used. The ACPI method expects a 24 byte params struct.
+ *
+ * This is the parameters structure for the WmiBrightnessNotify ACPI method as
+ * wrapped by WMI. The value passed in to @val or returned by @ret will be a
+ * brightness value when the WMI method ID is %WMI_BRIGHTNESS_METHOD_LEVEL, or
+ * an &enum wmi_brightness_source value with %WMI_BRIGHTNESS_METHOD_SOURCE.
+ */
+struct wmi_brightness_args {
+	u32 mode;
+	u32 val;
+	u32 ret;
+	u32 ignored[3];
+};
+
+/**
+ * wmi_brightness_notify() - helper function for calling WMI-wrapped ACPI method
+ * @w:    Pointer to the struct wmi_device identified by %WMI_BRIGHTNESS_GUID
+ * @id:   The WMI method ID to call (e.g. %WMI_BRIGHTNESS_METHOD_LEVEL or
+ *        %WMI_BRIGHTNESS_METHOD_SOURCE)
+ * @mode: The operation to perform on the method (e.g. %WMI_BRIGHTNESS_MODE_SET
+ *        or %WMI_BRIGHTNESS_MODE_GET)
+ * @val:  Pointer to a value passed in by the caller when @mode is
+ *        %WMI_BRIGHTNESS_MODE_SET, or a value passed out to caller when @mode
+ *        is %WMI_BRIGHTNESS_MODE_GET or %WMI_BRIGHTNESS_MODE_GET_MAX_LEVEL.
+ *
+ * Returns 0 on success, or a negative error number on failure.
+ */
+static int wmi_brightness_notify(struct wmi_device *w, enum wmi_brightness_method id, enum wmi_brightness_mode mode, u32 *val)
+{
+	struct wmi_brightness_args args = {
+		.mode = mode,
+		.val = 0,
+		.ret = 0,
+	};
+	struct acpi_buffer buf = { (acpi_size)sizeof(args), &args };
+	acpi_status status;
+
+	if (id < WMI_BRIGHTNESS_METHOD_LEVEL ||
+	    id >= WMI_BRIGHTNESS_METHOD_MAX ||
+	    mode < WMI_BRIGHTNESS_MODE_GET || mode >= WMI_BRIGHTNESS_MODE_MAX)
+		return -EINVAL;
+
+	if (mode == WMI_BRIGHTNESS_MODE_SET)
+		args.val = *val;
+
+	status = wmidev_evaluate_method(w, 0, id, &buf, &buf);
+	if (ACPI_FAILURE(status)) {
+		dev_err(&w->dev, "EC backlight control failed: %s\n",
+			acpi_format_exception(status));
+		return -EIO;
+	}
+
+	if (mode != WMI_BRIGHTNESS_MODE_SET)
+		*val = args.ret;
+
+	return 0;
+}
+
+static int nvidia_wmi_ec_backlight_update_status(struct backlight_device *bd)
+{
+	struct wmi_device *wdev = bl_get_data(bd);
+
+	return wmi_brightness_notify(wdev, WMI_BRIGHTNESS_METHOD_LEVEL,
+	                             WMI_BRIGHTNESS_MODE_SET,
+			             &bd->props.brightness);
+}
+
+static int nvidia_wmi_ec_backlight_get_brightness(struct backlight_device *bd)
+{
+	struct wmi_device *wdev = bl_get_data(bd);
+	u32 level;
+	int ret;
+
+	ret = wmi_brightness_notify(wdev, WMI_BRIGHTNESS_METHOD_LEVEL,
+	                            WMI_BRIGHTNESS_MODE_GET, &level);
+	if (ret < 0)
+		return ret;
+
+	return level;
+}
+
+static const struct backlight_ops nvidia_wmi_ec_backlight_ops = {
+	.update_status = nvidia_wmi_ec_backlight_update_status,
+	.get_brightness = nvidia_wmi_ec_backlight_get_brightness,
+};
+
+static int nvidia_wmi_ec_backlight_probe(struct wmi_device *wdev, const void *ctx)
+{
+	struct backlight_properties props = {};
+	struct backlight_device *bdev;
+	u32 source;
+	int ret;
+
+	ret = wmi_brightness_notify(wdev, WMI_BRIGHTNESS_METHOD_SOURCE,
+	                           WMI_BRIGHTNESS_MODE_GET, &source);
+	if (ret)
+		return ret;
+
+	/*
+	 * This driver is only to be used when brightness control is handled
+	 * by the EC; otherwise, the GPU driver(s) should control brightness.
+	 */
+	if (source != WMI_BRIGHTNESS_SOURCE_EC)
+		return -ENODEV;
+
+	/*
+	 * Identify this backlight device as a firmware device so that it can
+	 * be prioritized over any exposed GPU-driven raw device(s).
+	 */
+	props.type = BACKLIGHT_FIRMWARE;
+
+	ret = wmi_brightness_notify(wdev, WMI_BRIGHTNESS_METHOD_LEVEL,
+	                           WMI_BRIGHTNESS_MODE_GET_MAX_LEVEL,
+	                           &props.max_brightness);
+	if (ret)
+		return ret;
+
+	ret = wmi_brightness_notify(wdev, WMI_BRIGHTNESS_METHOD_LEVEL,
+	                           WMI_BRIGHTNESS_MODE_GET, &props.brightness);
+	if (ret)
+		return ret;
+
+	bdev = devm_backlight_device_register(&wdev->dev,
+	                                      "nvidia_wmi_ec_backlight",
+					      &wdev->dev, wdev,
+					      &nvidia_wmi_ec_backlight_ops,
+					      &props);
+	return PTR_ERR_OR_ZERO(bdev);
+}
+
+#define WMI_BRIGHTNESS_GUID "603E9613-EF25-4338-A3D0-C46177516DB7"
+
+static const struct wmi_device_id nvidia_wmi_ec_backlight_id_table[] = {
+	{ .guid_string = WMI_BRIGHTNESS_GUID },
+	{ }
+};
+MODULE_DEVICE_TABLE(wmi, nvidia_wmi_ec_backlight_id_table);
+
+static struct wmi_driver nvidia_wmi_ec_backlight_driver = {
+	.driver = {
+		.name = "nvidia-wmi-ec-backlight",
+	},
+	.probe = nvidia_wmi_ec_backlight_probe,
+	.id_table = nvidia_wmi_ec_backlight_id_table,
+};
+module_wmi_driver(nvidia_wmi_ec_backlight_driver);
+
+MODULE_AUTHOR("Daniel Dadap <ddadap@nvidia.com>");
+MODULE_DESCRIPTION("NVIDIA WMI EC Backlight driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/panasonic-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/panasonic-laptop.c
@@ -119,20 +119,22 @@
  *		- v0.1  start from toshiba_acpi driver written by John Belmonte
  */
 
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/types.h>
+#include <linux/acpi.h>
 #include <linux/backlight.h>
 #include <linux/ctype.h>
-#include <linux/seq_file.h>
-#include <linux/uaccess.h>
-#include <linux/slab.h>
-#include <linux/acpi.h>
+#include <linux/i8042.h>
+#include <linux/init.h>
 #include <linux/input.h>
 #include <linux/input/sparse-keymap.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/platform_device.h>
-
+#include <linux/seq_file.h>
+#include <linux/serio.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+#include <acpi/video.h>
 
 MODULE_AUTHOR("Hiroshi Miura <miura@da-cha.org>");
 MODULE_AUTHOR("David Bronaugh <dbronaugh@linuxboxen.org>");
@@ -241,6 +243,42 @@
 	struct platform_device	*platform;
 };
 
+/*
+ * On some Panasonic models the volume up / down / mute keys send duplicate
+ * keypress events over the PS/2 kbd interface, filter these out.
+ */
+static bool panasonic_i8042_filter(unsigned char data, unsigned char str,
+				   struct serio *port)
+{
+	static bool extended;
+
+	if (str & I8042_STR_AUXDATA)
+		return false;
+
+	if (data == 0xe0) {
+		extended = true;
+		return true;
+	} else if (extended) {
+		extended = false;
+
+		switch (data & 0x7f) {
+		case 0x20: /* e0 20 / e0 a0, Volume Mute press / release */
+		case 0x2e: /* e0 2e / e0 ae, Volume Down press / release */
+		case 0x30: /* e0 30 / e0 b0, Volume Up press / release */
+			return true;
+		default:
+			/*
+			 * Report the previously filtered e0 before continuing
+			 * with the next non-filtered byte.
+			 */
+			serio_interrupt(port, 0xe0, 0);
+			return false;
+		}
+	}
+
+	return false;
+}
+
 /* method access functions */
 static int acpi_pcc_write_sset(struct pcc_acpi *pcc, int func, int val)
 {
@@ -299,7 +337,8 @@
 	}
 
 	if (pcc->num_sifr < hkey->package.count) {
-		pr_err("SQTY reports bad SINF length\n");
+		pr_err("SQTY reports bad SINF length SQTY: %lu SINF-pkg-count: %u\n",
+		       pcc->num_sifr, hkey->package.count);
 		status = AE_ERROR;
 		goto end;
 	}
@@ -470,7 +509,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sinf[SINF_NUM_BATTERIES]);
+	return sysfs_emit(buf, "%u\n", pcc->sinf[SINF_NUM_BATTERIES]);
 }
 
 static ssize_t lcdtype_show(struct device *dev, struct device_attribute *attr,
@@ -482,7 +521,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sinf[SINF_LCD_TYPE]);
+	return sysfs_emit(buf, "%u\n", pcc->sinf[SINF_LCD_TYPE]);
 }
 
 static ssize_t mute_show(struct device *dev, struct device_attribute *attr,
@@ -494,7 +533,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sinf[SINF_MUTE]);
+	return sysfs_emit(buf, "%u\n", pcc->sinf[SINF_MUTE]);
 }
 
 static ssize_t mute_store(struct device *dev, struct device_attribute *attr,
@@ -524,7 +563,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sticky_key);
+	return sysfs_emit(buf, "%u\n", pcc->sticky_key);
 }
 
 static ssize_t sticky_key_store(struct device *dev, struct device_attribute *attr,
@@ -563,10 +602,9 @@
 		result = 1;
 		break;
 	default:
-		result = -EIO;
-		break;
+		return -EIO;
 	}
-	return snprintf(buf, PAGE_SIZE, "%u\n", result);
+	return sysfs_emit(buf, "%u\n", result);
 }
 
 static ssize_t eco_mode_store(struct device *dev, struct device_attribute *attr,
@@ -625,7 +663,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sinf[SINF_AC_CUR_BRIGHT]);
+	return sysfs_emit(buf, "%u\n", pcc->sinf[SINF_AC_CUR_BRIGHT]);
 }
 
 static ssize_t ac_brightness_store(struct device *dev, struct device_attribute *attr,
@@ -655,7 +693,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sinf[SINF_DC_CUR_BRIGHT]);
+	return sysfs_emit(buf, "%u\n", pcc->sinf[SINF_DC_CUR_BRIGHT]);
 }
 
 static ssize_t dc_brightness_store(struct device *dev, struct device_attribute *attr,
@@ -685,7 +723,7 @@
 	if (!acpi_pcc_retrieve_biosdata(pcc))
 		return -EIO;
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", pcc->sinf[SINF_CUR_BRIGHT]);
+	return sysfs_emit(buf, "%u\n", pcc->sinf[SINF_CUR_BRIGHT]);
 }
 
 static ssize_t current_brightness_store(struct device *dev, struct device_attribute *attr,
@@ -710,7 +748,12 @@
 static ssize_t cdpower_show(struct device *dev, struct device_attribute *attr,
 			    char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%d\n", get_optd_power_state());
+	int state = get_optd_power_state();
+
+	if (state < 0)
+		return state;
+
+	return sysfs_emit(buf, "%d\n", state);
 }
 
 static ssize_t cdpower_store(struct device *dev, struct device_attribute *attr,
@@ -735,6 +778,24 @@
 static DEVICE_ATTR_RW(current_brightness);
 static DEVICE_ATTR_RW(cdpower);
 
+static umode_t pcc_sysfs_is_visible(struct kobject *kobj, struct attribute *attr, int idx)
+{
+	struct device *dev = kobj_to_dev(kobj);
+	struct acpi_device *acpi = to_acpi_device(dev);
+	struct pcc_acpi *pcc = acpi_driver_data(acpi);
+
+	if (attr == &dev_attr_mute.attr)
+		return (pcc->num_sifr > SINF_MUTE) ? attr->mode : 0;
+
+	if (attr == &dev_attr_eco_mode.attr)
+		return (pcc->num_sifr > SINF_ECO_MODE) ? attr->mode : 0;
+
+	if (attr == &dev_attr_current_brightness.attr)
+		return (pcc->num_sifr > SINF_CUR_BRIGHT) ? attr->mode : 0;
+
+	return attr->mode;
+}
+
 static struct attribute *pcc_sysfs_entries[] = {
 	&dev_attr_numbatt.attr,
 	&dev_attr_lcdtype.attr,
@@ -749,8 +810,9 @@
 };
 
 static const struct attribute_group pcc_attr_group = {
-	.name	= NULL,		/* put in device directory */
-	.attrs	= pcc_sysfs_entries,
+	.name		= NULL,		/* put in device directory */
+	.attrs		= pcc_sysfs_entries,
+	.is_visible	= pcc_sysfs_is_visible,
 };
 
 
@@ -762,6 +824,8 @@
 	struct input_dev *hotk_input_dev = pcc->input_dev;
 	int rc;
 	unsigned long long result;
+	unsigned int key;
+	unsigned int updown;
 
 	rc = acpi_evaluate_integer(pcc->handle, METHOD_HKEY_QUERY,
 				   NULL, &result);
@@ -770,20 +834,27 @@
 		return;
 	}
 
+	key = result & 0xf;
+	updown = result & 0x80; /* 0x80 == key down; 0x00 = key up */
+
 	/* hack: some firmware sends no key down for sleep / hibernate */
-	if ((result & 0xf) == 0x7 || (result & 0xf) == 0xa) {
-		if (result & 0x80)
+	if (key == 7 || key == 10) {
+		if (updown)
 			sleep_keydown_seen = 1;
 		if (!sleep_keydown_seen)
 			sparse_keymap_report_event(hotk_input_dev,
-					result & 0xf, 0x80, false);
+					key, 0x80, false);
 	}
 
-	if ((result & 0xf) == 0x7 || (result & 0xf) == 0x9 || (result & 0xf) == 0xa) {
-		if (!sparse_keymap_report_event(hotk_input_dev,
-						result & 0xf, result & 0x80, false))
-			pr_err("Unknown hotkey event: 0x%04llx\n", result);
-	}
+	/*
+	 * Don't report brightness key-presses if they are also reported
+	 * by the ACPI video bus.
+	 */
+	if ((key == 1 || key == 2) && acpi_video_handles_brightness_key_presses())
+		return;
+
+	if (!sparse_keymap_report_event(hotk_input_dev, key, updown, false))
+		pr_err("Unknown hotkey event: 0x%04llx\n", result);
 }
 
 static void acpi_pcc_hotkey_notify(struct acpi_device *device, u32 event)
@@ -894,12 +965,15 @@
 	if (!pcc)
 		return -EINVAL;
 
-	acpi_pcc_write_sset(pcc, SINF_MUTE, pcc->mute);
-	acpi_pcc_write_sset(pcc, SINF_ECO_MODE, pcc->eco_mode);
+	if (pcc->num_sifr > SINF_MUTE)
+		acpi_pcc_write_sset(pcc, SINF_MUTE, pcc->mute);
+	if (pcc->num_sifr > SINF_ECO_MODE)
+		acpi_pcc_write_sset(pcc, SINF_ECO_MODE, pcc->eco_mode);
 	acpi_pcc_write_sset(pcc, SINF_STICKY_KEY, pcc->sticky_key);
 	acpi_pcc_write_sset(pcc, SINF_AC_CUR_BRIGHT, pcc->ac_brightness);
 	acpi_pcc_write_sset(pcc, SINF_DC_CUR_BRIGHT, pcc->dc_brightness);
-	acpi_pcc_write_sset(pcc, SINF_CUR_BRIGHT, pcc->current_brightness);
+	if (pcc->num_sifr > SINF_CUR_BRIGHT)
+		acpi_pcc_write_sset(pcc, SINF_CUR_BRIGHT, pcc->current_brightness);
 
 	return 0;
 }
@@ -916,11 +990,21 @@
 
 	num_sifr = acpi_pcc_get_sqty(device);
 
-	if (num_sifr < 0 || num_sifr > 255) {
-		pr_err("num_sifr out of range");
+	/*
+	 * pcc->sinf is expected to at least have the AC+DC brightness entries.
+	 * Accesses to higher SINF entries are checked against num_sifr.
+	 */
+	if (num_sifr <= SINF_DC_CUR_BRIGHT || num_sifr > 255) {
+		pr_err("num_sifr %d out of range %d - 255\n", num_sifr, SINF_DC_CUR_BRIGHT + 1);
 		return -ENODEV;
 	}
 
+	/*
+	 * Some DSDT-s have an off-by-one bug where the SINF package count is
+	 * one higher than the SQTY reported value, allocate 1 entry extra.
+	 */
+	num_sifr++;
+
 	pcc = kzalloc(sizeof(struct pcc_acpi), GFP_KERNEL);
 	if (!pcc) {
 		pr_err("Couldn't allocate mem for pcc");
@@ -969,11 +1053,14 @@
 	acpi_pcc_write_sset(pcc, SINF_STICKY_KEY, 0);
 	pcc->sticky_key = 0;
 
-	pcc->eco_mode = pcc->sinf[SINF_ECO_MODE];
-	pcc->mute = pcc->sinf[SINF_MUTE];
 	pcc->ac_brightness = pcc->sinf[SINF_AC_CUR_BRIGHT];
 	pcc->dc_brightness = pcc->sinf[SINF_DC_CUR_BRIGHT];
-	pcc->current_brightness = pcc->sinf[SINF_CUR_BRIGHT];
+	if (pcc->num_sifr > SINF_MUTE)
+		pcc->mute = pcc->sinf[SINF_MUTE];
+	if (pcc->num_sifr > SINF_ECO_MODE)
+		pcc->eco_mode = pcc->sinf[SINF_ECO_MODE];
+	if (pcc->num_sifr > SINF_CUR_BRIGHT)
+		pcc->current_brightness = pcc->sinf[SINF_CUR_BRIGHT];
 
 	/* add sysfs attributes */
 	result = sysfs_create_group(&device->dev.kobj, &pcc_attr_group);
@@ -997,6 +1084,7 @@
 		pcc->platform = NULL;
 	}
 
+	i8042_install_filter(panasonic_i8042_filter);
 	return 0;
 
 out_platform:
@@ -1020,6 +1108,8 @@
 	if (!device || !pcc)
 		return -EINVAL;
 
+	i8042_remove_filter(panasonic_i8042_filter);
+
 	if (pcc->platform) {
 		device_remove_file(&pcc->platform->dev, &dev_attr_cdpower);
 		platform_device_unregister(pcc->platform);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/pmc_atom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/pmc_atom.c
@@ -244,7 +244,7 @@
 	pm1_cnt_port = acpi_base_addr + PM1_CNT;
 
 	pm1_cnt_value = inl(pm1_cnt_port);
-	pm1_cnt_value &= SLEEP_TYPE_MASK;
+	pm1_cnt_value &= ~SLEEP_TYPE_MASK;
 	pm1_cnt_value |= SLEEP_TYPE_S5;
 	pm1_cnt_value |= SLEEP_ENABLE;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/samsung-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/samsung-laptop.c
@@ -1121,8 +1121,6 @@
 
 	if (value > samsung->kbd_led.max_brightness)
 		value = samsung->kbd_led.max_brightness;
-	else if (value < 0)
-		value = 0;
 
 	samsung->kbd_led_wk = value;
 	queue_work(samsung->led_workqueue, &samsung->kbd_led_work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/serial-multi-instantiate.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/serial-multi-instantiate.c
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Serial multi-instantiate driver, pseudo driver to instantiate multiple
+ * client devices from a single fwnode.
+ *
+ * Copyright 2018 Hans de Goede <hdegoede@redhat.com>
+ */
+
+#include <linux/acpi.h>
+#include <linux/bits.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+
+#define IRQ_RESOURCE_TYPE	GENMASK(1, 0)
+#define IRQ_RESOURCE_NONE	0
+#define IRQ_RESOURCE_GPIO	1
+#define IRQ_RESOURCE_APIC	2
+
+enum smi_bus_type {
+	SMI_I2C,
+	SMI_SPI,
+	SMI_AUTO_DETECT,
+};
+
+struct smi_instance {
+	const char *type;
+	unsigned int flags;
+	int irq_idx;
+};
+
+struct smi_node {
+	enum smi_bus_type bus_type;
+	struct smi_instance instances[];
+};
+
+struct smi {
+	int i2c_num;
+	int spi_num;
+	struct i2c_client **i2c_devs;
+	struct spi_device **spi_devs;
+};
+
+static int smi_get_irq(struct platform_device *pdev, struct acpi_device *adev,
+		       const struct smi_instance *inst)
+{
+	int ret;
+
+	switch (inst->flags & IRQ_RESOURCE_TYPE) {
+	case IRQ_RESOURCE_GPIO:
+		ret = acpi_dev_gpio_irq_get(adev, inst->irq_idx);
+		break;
+	case IRQ_RESOURCE_APIC:
+		ret = platform_get_irq(pdev, inst->irq_idx);
+		break;
+	default:
+		return 0;
+	}
+
+	if (ret < 0)
+		dev_err_probe(&pdev->dev, ret, "Error requesting irq at index %d: %d\n",
+			      inst->irq_idx, ret);
+
+	return ret;
+}
+
+static void smi_devs_unregister(struct smi *smi)
+{
+	while (smi->i2c_num > 0)
+		i2c_unregister_device(smi->i2c_devs[--smi->i2c_num]);
+
+	while (smi->spi_num > 0)
+		spi_unregister_device(smi->spi_devs[--smi->spi_num]);
+}
+
+/**
+ * smi_spi_probe - Instantiate multiple SPI devices from inst array
+ * @pdev:	Platform device
+ * @adev:	ACPI device
+ * @smi:	Internal struct for Serial multi instantiate driver
+ * @inst_array:	Array of instances to probe
+ *
+ * Returns the number of SPI devices instantiate, Zero if none is found or a negative error code.
+ */
+static int smi_spi_probe(struct platform_device *pdev, struct acpi_device *adev, struct smi *smi,
+			 const struct smi_instance *inst_array)
+{
+	struct device *dev = &pdev->dev;
+	struct spi_controller *ctlr;
+	struct spi_device *spi_dev;
+	char name[50];
+	int i, ret, count;
+
+	ret = acpi_spi_count_resources(adev);
+	if (ret < 0)
+		return ret;
+	else if (!ret)
+		return -ENODEV;
+
+	count = ret;
+
+	smi->spi_devs = devm_kcalloc(dev, count, sizeof(*smi->spi_devs), GFP_KERNEL);
+	if (!smi->spi_devs)
+		return -ENOMEM;
+
+	for (i = 0; i < count && inst_array[i].type; i++) {
+
+		spi_dev = acpi_spi_device_alloc(NULL, adev, i);
+		if (IS_ERR(spi_dev)) {
+			ret = PTR_ERR(spi_dev);
+			dev_err_probe(dev, ret, "failed to allocate SPI device %s from ACPI: %d\n",
+				      dev_name(&adev->dev), ret);
+			goto error;
+		}
+
+		ctlr = spi_dev->controller;
+
+		strscpy(spi_dev->modalias, inst_array[i].type, sizeof(spi_dev->modalias));
+
+		ret = smi_get_irq(pdev, adev, &inst_array[i]);
+		if (ret < 0) {
+			spi_dev_put(spi_dev);
+			goto error;
+		}
+		spi_dev->irq = ret;
+
+		snprintf(name, sizeof(name), "%s-%s-%s.%d", dev_name(&ctlr->dev), dev_name(dev),
+			 inst_array[i].type, i);
+		spi_dev->dev.init_name = name;
+
+		ret = spi_add_device(spi_dev);
+		if (ret) {
+			dev_err_probe(&ctlr->dev, ret,
+				      "failed to add SPI device %s from ACPI: %d\n",
+				      dev_name(&adev->dev), ret);
+			spi_dev_put(spi_dev);
+			goto error;
+		}
+
+		dev_dbg(dev, "SPI device %s using chip select %u", name, spi_dev->chip_select);
+
+		smi->spi_devs[i] = spi_dev;
+		smi->spi_num++;
+	}
+
+	if (smi->spi_num < count) {
+		dev_dbg(dev, "Error finding driver, idx %d\n", i);
+		ret = -ENODEV;
+		goto error;
+	}
+
+	dev_info(dev, "Instantiated %d SPI devices.\n", smi->spi_num);
+
+	return 0;
+error:
+	smi_devs_unregister(smi);
+
+	return ret;
+}
+
+/**
+ * smi_i2c_probe - Instantiate multiple I2C devices from inst array
+ * @pdev:	Platform device
+ * @adev:	ACPI device
+ * @smi:	Internal struct for Serial multi instantiate driver
+ * @inst_array:	Array of instances to probe
+ *
+ * Returns the number of I2C devices instantiate, Zero if none is found or a negative error code.
+ */
+static int smi_i2c_probe(struct platform_device *pdev, struct acpi_device *adev, struct smi *smi,
+			 const struct smi_instance *inst_array)
+{
+	struct i2c_board_info board_info = {};
+	struct device *dev = &pdev->dev;
+	char name[32];
+	int i, ret, count;
+
+	ret = i2c_acpi_client_count(adev);
+	if (ret < 0)
+		return ret;
+	else if (!ret)
+		return -ENODEV;
+
+	count = ret;
+
+	smi->i2c_devs = devm_kcalloc(dev, count, sizeof(*smi->i2c_devs), GFP_KERNEL);
+	if (!smi->i2c_devs)
+		return -ENOMEM;
+
+	for (i = 0; i < count && inst_array[i].type; i++) {
+		memset(&board_info, 0, sizeof(board_info));
+		strscpy(board_info.type, inst_array[i].type, I2C_NAME_SIZE);
+		snprintf(name, sizeof(name), "%s-%s.%d", dev_name(dev), inst_array[i].type, i);
+		board_info.dev_name = name;
+
+		ret = smi_get_irq(pdev, adev, &inst_array[i]);
+		if (ret < 0)
+			goto error;
+		board_info.irq = ret;
+
+		smi->i2c_devs[i] = i2c_acpi_new_device(dev, i, &board_info);
+		if (IS_ERR(smi->i2c_devs[i])) {
+			ret = dev_err_probe(dev, PTR_ERR(smi->i2c_devs[i]),
+					    "Error creating i2c-client, idx %d\n", i);
+			goto error;
+		}
+		smi->i2c_num++;
+	}
+	if (smi->i2c_num < count) {
+		dev_dbg(dev, "Error finding driver, idx %d\n", i);
+		ret = -ENODEV;
+		goto error;
+	}
+
+	dev_info(dev, "Instantiated %d I2C devices.\n", smi->i2c_num);
+
+	return 0;
+error:
+	smi_devs_unregister(smi);
+
+	return ret;
+}
+
+static int smi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct smi_node *node;
+	struct acpi_device *adev;
+	struct smi *smi;
+
+	adev = ACPI_COMPANION(dev);
+	if (!adev)
+		return -ENODEV;
+
+	node = device_get_match_data(dev);
+	if (!node) {
+		dev_dbg(dev, "Error ACPI match data is missing\n");
+		return -ENODEV;
+	}
+
+	smi = devm_kzalloc(dev, sizeof(*smi), GFP_KERNEL);
+	if (!smi)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, smi);
+
+	switch (node->bus_type) {
+	case SMI_I2C:
+		return smi_i2c_probe(pdev, adev, smi, node->instances);
+	case SMI_SPI:
+		return smi_spi_probe(pdev, adev, smi, node->instances);
+	case SMI_AUTO_DETECT:
+		if (i2c_acpi_client_count(adev) > 0)
+			return smi_i2c_probe(pdev, adev, smi, node->instances);
+		else
+			return smi_spi_probe(pdev, adev, smi, node->instances);
+	default:
+		return -EINVAL;
+	}
+
+	return 0; /* never reached */
+}
+
+static int smi_remove(struct platform_device *pdev)
+{
+	struct smi *smi = platform_get_drvdata(pdev);
+
+	smi_devs_unregister(smi);
+
+	return 0;
+}
+
+static const struct smi_node bsg1160_data = {
+	.instances = {
+		{ "bmc150_accel", IRQ_RESOURCE_GPIO, 0 },
+		{ "bmc150_magn" },
+		{ "bmg160" },
+		{}
+	},
+	.bus_type = SMI_I2C,
+};
+
+static const struct smi_node bsg2150_data = {
+	.instances = {
+		{ "bmc150_accel", IRQ_RESOURCE_GPIO, 0 },
+		{ "bmc150_magn" },
+		/* The resources describe a 3th client, but it is not really there. */
+		{ "bsg2150_dummy_dev" },
+		{}
+	},
+	.bus_type = SMI_I2C,
+};
+
+static const struct smi_node int3515_data = {
+	.instances = {
+		{ "tps6598x", IRQ_RESOURCE_APIC, 0 },
+		{ "tps6598x", IRQ_RESOURCE_APIC, 1 },
+		{ "tps6598x", IRQ_RESOURCE_APIC, 2 },
+		{ "tps6598x", IRQ_RESOURCE_APIC, 3 },
+		{}
+	},
+	.bus_type = SMI_I2C,
+};
+
+static const struct smi_node cs35l41_hda = {
+	.instances = {
+		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
+		{}
+	},
+	.bus_type = SMI_AUTO_DETECT,
+};
+
+/*
+ * Note new device-ids must also be added to ignore_serial_bus_ids in
+ * drivers/acpi/scan.c: acpi_device_enumeration_by_parent().
+ */
+static const struct acpi_device_id smi_acpi_ids[] = {
+	{ "BSG1160", (unsigned long)&bsg1160_data },
+	{ "BSG2150", (unsigned long)&bsg2150_data },
+	{ "INT3515", (unsigned long)&int3515_data },
+	{ "CSC3551", (unsigned long)&cs35l41_hda },
+	/* Non-conforming _HID for Cirrus Logic already released */
+	{ "CLSA0100", (unsigned long)&cs35l41_hda },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, smi_acpi_ids);
+
+static struct platform_driver smi_driver = {
+	.driver	= {
+		.name = "Serial bus multi instantiate pseudo device driver",
+		.acpi_match_table = smi_acpi_ids,
+	},
+	.probe = smi_probe,
+	.remove = smi_remove,
+};
+module_platform_driver(smi_driver);
+
+MODULE_DESCRIPTION("Serial multi instantiate pseudo device driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/sony-laptop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/sony-laptop.c
@@ -1892,14 +1892,21 @@
 		break;
 	}
 
-	ret = sony_call_snc_handle(handle, probe_base, &result);
-	if (ret)
-		return ret;
+	/*
+	 * Only probe if there is a separate probe_base, otherwise the probe call
+	 * is equivalent to __sony_nc_kbd_backlight_mode_set(0), resulting in
+	 * the keyboard backlight being turned off.
+	 */
+	if (probe_base) {
+		ret = sony_call_snc_handle(handle, probe_base, &result);
+		if (ret)
+			return ret;
 
-	if ((handle == 0x0137 && !(result & 0x02)) ||
-			!(result & 0x01)) {
-		dprintk("no backlight keyboard found\n");
-		return 0;
+		if ((handle == 0x0137 && !(result & 0x02)) ||
+				!(result & 0x01)) {
+			dprintk("no backlight keyboard found\n");
+			return 0;
+		}
 	}
 
 	kbdbl_ctl = kzalloc(sizeof(*kbdbl_ctl), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/think-lmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/think-lmi.c
@@ -504,7 +504,7 @@
 static ssize_t current_value_show(struct kobject *kobj, struct kobj_attribute *attr, char *buf)
 {
 	struct tlmi_attr_setting *setting = to_tlmi_attr_setting(kobj);
-	char *item, *value;
+	char *item, *value, *p;
 	int ret;
 
 	ret = tlmi_setting(setting->index, &item, LENOVO_BIOS_SETTING_GUID);
@@ -514,10 +514,15 @@
 	/* validate and split from `item,value` -> `value` */
 	value = strpbrk(item, ",");
 	if (!value || value == item || !strlen(value + 1))
-		return -EINVAL;
-
-	ret = sysfs_emit(buf, "%s\n", value + 1);
+		ret = -EINVAL;
+	else {
+		/* On Workstations remove the Options part after the value */
+		p = strchrnul(value, ';');
+		*p = '\0';
+		ret = sysfs_emit(buf, "%s\n", value + 1);
+	}
 	kfree(item);
+
 	return ret;
 }
 
@@ -525,12 +530,23 @@
 {
 	struct tlmi_attr_setting *setting = to_tlmi_attr_setting(kobj);
 
-	if (!tlmi_priv.can_get_bios_selections)
-		return -EOPNOTSUPP;
-
 	return sysfs_emit(buf, "%s\n", setting->possible_values);
 }
 
+static ssize_t type_show(struct kobject *kobj, struct kobj_attribute *attr,
+		char *buf)
+{
+	struct tlmi_attr_setting *setting = to_tlmi_attr_setting(kobj);
+
+	if (setting->possible_values) {
+		/* Figure out what setting type is as BIOS does not return this */
+		if (strchr(setting->possible_values, ';'))
+			return sysfs_emit(buf, "enumeration\n");
+	}
+	/* Anything else is going to be a string */
+	return sysfs_emit(buf, "string\n");
+}
+
 static ssize_t current_value_store(struct kobject *kobj,
 		struct kobj_attribute *attr,
 		const char *buf, size_t count)
@@ -601,14 +617,30 @@
 
 static struct kobj_attribute attr_current_val = __ATTR_RW_MODE(current_value, 0600);
 
+static struct kobj_attribute attr_type = __ATTR_RO(type);
+
+static umode_t attr_is_visible(struct kobject *kobj,
+					     struct attribute *attr, int n)
+{
+	struct tlmi_attr_setting *setting = to_tlmi_attr_setting(kobj);
+
+	/* We don't want to display possible_values attributes if not available */
+	if ((attr == &attr_possible_values.attr) && (!setting->possible_values))
+		return 0;
+
+	return attr->mode;
+}
+
 static struct attribute *tlmi_attrs[] = {
 	&attr_displ_name.attr,
 	&attr_current_val.attr,
 	&attr_possible_values.attr,
+	&attr_type.attr,
 	NULL
 };
 
 static const struct attribute_group tlmi_attr_group = {
+	.is_visible = attr_is_visible,
 	.attrs = tlmi_attrs,
 };
 
@@ -755,6 +787,24 @@
 	kset_unregister(tlmi_priv.authentication_kset);
 }
 
+static int tlmi_validate_setting_name(struct kset *attribute_kset, char *name)
+{
+	struct kobject *duplicate;
+
+	if (!strcmp(name, "Reserved"))
+		return -EINVAL;
+
+	duplicate = kset_find_obj(attribute_kset, name);
+	if (duplicate) {
+		pr_debug("Duplicate attribute name found - %s\n", name);
+		/* kset_find_obj() returns a reference */
+		kobject_put(duplicate);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 static int tlmi_sysfs_init(void)
 {
 	int i, ret;
@@ -783,10 +833,8 @@
 			continue;
 
 		/* check for duplicate or reserved values */
-		if (kset_find_obj(tlmi_priv.attribute_kset, tlmi_priv.setting[i]->display_name) ||
-		    !strcmp(tlmi_priv.setting[i]->display_name, "Reserved")) {
-			pr_debug("duplicate or reserved attribute name found - %s\n",
-				tlmi_priv.setting[i]->display_name);
+		if (tlmi_validate_setting_name(tlmi_priv.attribute_kset,
+					       tlmi_priv.setting[i]->display_name) < 0) {
 			kfree(tlmi_priv.setting[i]->possible_values);
 			kfree(tlmi_priv.setting[i]);
 			tlmi_priv.setting[i] = NULL;
@@ -888,8 +936,10 @@
 			break;
 		if (!item)
 			break;
-		if (!*item)
+		if (!*item) {
+			kfree(item);
 			continue;
+		}
 
 		/* It is not allowed to have '/' for file name. Convert it into '\'. */
 		strreplace(item, '/', '\\');
@@ -902,6 +952,7 @@
 		setting = kzalloc(sizeof(*setting), GFP_KERNEL);
 		if (!setting) {
 			ret = -ENOMEM;
+			kfree(item);
 			goto fail_clear_attr;
 		}
 		setting->index = i;
@@ -913,10 +964,37 @@
 			if (ret || !setting->possible_values)
 				pr_info("Error retrieving possible values for %d : %s\n",
 						i, setting->display_name);
+		} else {
+			/*
+			 * Older Thinkstations don't support the bios_selections API.
+			 * Instead they store this as a [Optional:Option1,Option2] section of the
+			 * name string.
+			 * Try and pull that out if it's available.
+			 */
+			char *optitem, *optstart, *optend;
+
+			if (!tlmi_setting(setting->index, &optitem, LENOVO_BIOS_SETTING_GUID)) {
+				optstart = strstr(optitem, "[Optional:");
+				if (optstart) {
+					optstart += strlen("[Optional:");
+					optend = strstr(optstart, "]");
+					if (optend)
+						setting->possible_values =
+							kstrndup(optstart, optend - optstart,
+									GFP_KERNEL);
+				}
+				kfree(optitem);
+			}
 		}
+		/*
+		 * firmware-attributes requires that possible_values are separated by ';' but
+		 * Lenovo FW uses ','. Replace appropriately.
+		 */
+		if (setting->possible_values)
+			strreplace(setting->possible_values, ',', ';');
+
 		kobject_init(&setting->kobj, &tlmi_attr_setting_ktype);
 		tlmi_priv.setting[i] = setting;
-		tlmi_priv.settings_count++;
 		kfree(item);
 	}
 
@@ -983,7 +1061,12 @@
 
 static int tlmi_probe(struct wmi_device *wdev, const void *context)
 {
-	tlmi_analyze();
+	int ret;
+
+	ret = tlmi_analyze();
+	if (ret)
+		return ret;
+
 	return tlmi_sysfs_init();
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/think-lmi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/think-lmi.h
@@ -55,7 +55,6 @@
 struct think_lmi {
 	struct wmi_device *wmi_device;
 
-	int settings_count;
 	bool can_set_bios_settings;
 	bool can_get_bios_selections;
 	bool can_set_bios_password;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/thinkpad_acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/thinkpad_acpi.c
@@ -1178,15 +1178,6 @@
 	return status;
 }
 
-/* Query FW and update rfkill sw state for all rfkill switches */
-static void tpacpi_rfk_update_swstate_all(void)
-{
-	unsigned int i;
-
-	for (i = 0; i < TPACPI_RFK_SW_MAX; i++)
-		tpacpi_rfk_update_swstate(tpacpi_rfkill_switches[i]);
-}
-
 /*
  * Sync the HW-blocking state of all rfkill switches,
  * do notice it causes the rfkill core to schedule uevents
@@ -3129,9 +3120,6 @@
 	if (wlsw == TPACPI_RFK_RADIO_OFF)
 		tpacpi_rfk_update_hwblock_state(true);
 
-	/* Sync sw blocking state */
-	tpacpi_rfk_update_swstate_all();
-
 	/* Sync hw blocking state last if it is hw-unblocked */
 	if (wlsw == TPACPI_RFK_RADIO_ON)
 		tpacpi_rfk_update_hwblock_state(false);
@@ -8853,6 +8841,7 @@
 	TPACPI_Q_LNV3('N', '2', 'E', TPACPI_FAN_2CTL),	/* P1 / X1 Extreme (1st gen) */
 	TPACPI_Q_LNV3('N', '2', 'O', TPACPI_FAN_2CTL),	/* P1 / X1 Extreme (2nd gen) */
 	TPACPI_Q_LNV3('N', '2', 'V', TPACPI_FAN_2CTL),	/* P1 / X1 Extreme (3nd gen) */
+	TPACPI_Q_LNV3('N', '4', '0', TPACPI_FAN_2CTL),	/* P1 / X1 Extreme (4nd gen) */
 	TPACPI_Q_LNV3('N', '3', '0', TPACPI_FAN_2CTL),	/* P15 (1st gen) / P15v (1st gen) */
 	TPACPI_Q_LNV3('N', '3', '2', TPACPI_FAN_2CTL),	/* X1 Carbon (9th gen) */
 };
@@ -9145,7 +9134,7 @@
 
 	if (strlencmp(cmd, "level auto") == 0)
 		level = TP_EC_FAN_AUTO;
-	else if ((strlencmp(cmd, "level disengaged") == 0) |
+	else if ((strlencmp(cmd, "level disengaged") == 0) ||
 			(strlencmp(cmd, "level full-speed") == 0))
 		level = TP_EC_FAN_FULLSPEED;
 	else if (sscanf(cmd, "level %d", &level) != 1)
@@ -9777,6 +9766,8 @@
 	 * Individual addressing is broken on models that expose the
 	 * primary battery as BAT1.
 	 */
+	TPACPI_Q_LNV('G', '8', true),       /* ThinkPad X131e */
+	TPACPI_Q_LNV('8', 'F', true),       /* Thinkpad X120e */
 	TPACPI_Q_LNV('J', '7', true),       /* B5400 */
 	TPACPI_Q_LNV('J', 'I', true),       /* Thinkpad 11e */
 	TPACPI_Q_LNV3('R', '0', 'B', true), /* Thinkpad 11e gen 3 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/touchscreen_dmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/touchscreen_dmi.c
@@ -50,7 +50,7 @@
 };
 
 static const struct ts_dmi_data chuwi_hi8_air_data = {
-	.acpi_name	= "MSSL1680:00",
+	.acpi_name	= "MSSL1680",
 	.properties	= chuwi_hi8_air_props,
 };
 
@@ -255,6 +255,23 @@
 	.properties     = connect_tablet9_props,
 };
 
+static const struct property_entry csl_panther_tab_hd_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 1),
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 20),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1980),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1526),
+	PROPERTY_ENTRY_BOOL("touchscreen-inverted-y"),
+	PROPERTY_ENTRY_BOOL("touchscreen-swapped-x-y"),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-csl-panther-tab-hd.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	{ }
+};
+
+static const struct ts_dmi_data csl_panther_tab_hd_data = {
+	.acpi_name      = "MSSL1680:00",
+	.properties     = csl_panther_tab_hd_props,
+};
+
 static const struct property_entry cube_iwork8_air_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-min-x", 1),
 	PROPERTY_ENTRY_U32("touchscreen-min-y", 3),
@@ -310,6 +327,22 @@
 	.properties	= dexp_ursus_7w_props,
 };
 
+static const struct property_entry dexp_ursus_kx210i_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 5),
+	PROPERTY_ENTRY_U32("touchscreen-min-y",  2),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1720),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1137),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-dexp-ursus-kx210i.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	PROPERTY_ENTRY_BOOL("silead,home-button"),
+	{ }
+};
+
+static const struct ts_dmi_data dexp_ursus_kx210i_data = {
+	.acpi_name	= "MSSL1680:00",
+	.properties	= dexp_ursus_kx210i_props,
+};
+
 static const struct property_entry digma_citi_e200_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-size-x", 1980),
 	PROPERTY_ENTRY_U32("touchscreen-size-y", 1500),
@@ -364,6 +397,11 @@
 	.properties	= glavey_tm800a550l_props,
 };
 
+static const struct ts_dmi_data gdix1002_00_upside_down_data = {
+	.acpi_name	= "GDIX1002:00",
+	.properties	= gdix1001_upside_down_props,
+};
+
 static const struct property_entry gp_electronic_t701_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-size-x", 960),
 	PROPERTY_ENTRY_U32("touchscreen-size-y", 640),
@@ -705,6 +743,21 @@
 	.properties	= pipo_w11_props,
 };
 
+static const struct property_entry positivo_c4128b_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 4),
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 13),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1915),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1269),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-positivo-c4128b.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	{ }
+};
+
+static const struct ts_dmi_data positivo_c4128b_data = {
+	.acpi_name	= "MSSL1680:00",
+	.properties	= positivo_c4128b_props,
+};
+
 static const struct property_entry pov_mobii_wintab_p800w_v20_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-min-x", 32),
 	PROPERTY_ENTRY_U32("touchscreen-min-y", 16),
@@ -773,6 +826,52 @@
 	.properties	= predia_basic_props,
 };
 
+static const struct property_entry rca_cambio_w101_v2_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 4),
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 20),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1644),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 874),
+	PROPERTY_ENTRY_BOOL("touchscreen-swapped-x-y"),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-rca-cambio-w101-v2.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	{ }
+};
+
+static const struct ts_dmi_data rca_cambio_w101_v2_data = {
+	.acpi_name = "MSSL1680:00",
+	.properties = rca_cambio_w101_v2_props,
+};
+
+static const struct property_entry rwc_nanote_p8_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 46),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1728),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1140),
+	PROPERTY_ENTRY_BOOL("touchscreen-inverted-y"),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-rwc-nanote-p8.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	{ }
+};
+
+static const struct ts_dmi_data rwc_nanote_p8_data = {
+	.acpi_name = "MSSL1680:00",
+	.properties = rwc_nanote_p8_props,
+};
+
+static const struct property_entry rwc_nanote_next_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 5),
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 5),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1785),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1145),
+	PROPERTY_ENTRY_BOOL("touchscreen-inverted-y"),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-rwc-nanote-next.fw"),
+	{ }
+};
+
+static const struct ts_dmi_data rwc_nanote_next_data = {
+	.acpi_name = "MSSL1680:00",
+	.properties = rwc_nanote_next_props,
+};
+
 static const struct property_entry schneider_sct101ctm_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-size-x", 1715),
 	PROPERTY_ENTRY_U32("touchscreen-size-y", 1140),
@@ -790,6 +889,22 @@
 	.properties	= schneider_sct101ctm_props,
 };
 
+static const struct property_entry globalspace_solt_ivw116_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 7),
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 22),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1723),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1077),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl1680-globalspace-solt-ivw116.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	PROPERTY_ENTRY_BOOL("silead,home-button"),
+	{ }
+};
+
+static const struct ts_dmi_data globalspace_solt_ivw116_data = {
+	.acpi_name	= "MSSL1680:00",
+	.properties	= globalspace_solt_ivw116_props,
+};
+
 static const struct property_entry techbite_arc_11_6_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-min-x", 5),
 	PROPERTY_ENTRY_U32("touchscreen-min-y", 7),
@@ -832,6 +947,32 @@
 	.properties	= teclast_tbook11_props,
 };
 
+static const struct property_entry teclast_x16_plus_props[] = {
+	PROPERTY_ENTRY_U32("touchscreen-min-x", 8),
+	PROPERTY_ENTRY_U32("touchscreen-min-y", 14),
+	PROPERTY_ENTRY_U32("touchscreen-size-x", 1916),
+	PROPERTY_ENTRY_U32("touchscreen-size-y", 1264),
+	PROPERTY_ENTRY_BOOL("touchscreen-inverted-y"),
+	PROPERTY_ENTRY_STRING("firmware-name", "gsl3692-teclast-x16-plus.fw"),
+	PROPERTY_ENTRY_U32("silead,max-fingers", 10),
+	PROPERTY_ENTRY_BOOL("silead,home-button"),
+	{ }
+};
+
+static const struct ts_dmi_data teclast_x16_plus_data = {
+	.embedded_fw = {
+		.name	= "silead/gsl3692-teclast-x16-plus.fw",
+		.prefix = { 0xf0, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00 },
+		.length	= 43560,
+		.sha256	= { 0x9d, 0xb0, 0x3d, 0xf1, 0x00, 0x3c, 0xb5, 0x25,
+			    0x62, 0x8a, 0xa0, 0x93, 0x4b, 0xe0, 0x4e, 0x75,
+			    0xd1, 0x27, 0xb1, 0x65, 0x3c, 0xba, 0xa5, 0x0f,
+			    0xcd, 0xb4, 0xbe, 0x00, 0xbb, 0xf6, 0x43, 0x29 },
+	},
+	.acpi_name	= "MSSL1680:00",
+	.properties	= teclast_x16_plus_props,
+};
+
 static const struct property_entry teclast_x3_plus_props[] = {
 	PROPERTY_ENTRY_U32("touchscreen-size-x", 1980),
 	PROPERTY_ENTRY_U32("touchscreen-size-y", 1500),
@@ -1026,6 +1167,15 @@
 		},
 	},
 	{
+		/* Chuwi Vi8 (CWI501) */
+		.driver_data = (void *)&chuwi_vi8_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Insyde"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "i86"),
+			DMI_MATCH(DMI_BIOS_VERSION, "CHUWI.W86JLBNR01"),
+		},
+	},
+	{
 		/* Chuwi Vi8 (CWI506) */
 		.driver_data = (void *)&chuwi_vi8_data,
 		.matches = {
@@ -1035,6 +1185,15 @@
 		},
 	},
 	{
+		/* Chuwi Vi8 dual-boot (CWI506) */
+		.driver_data = (void *)&chuwi_vi8_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Insyde"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "i86"),
+			DMI_MATCH(DMI_BIOS_VERSION, "CHUWI2.D86JHBNR02"),
+		},
+	},
+	{
 		/* Chuwi Vi8 Plus (CWI519) */
 		.driver_data = (void *)&chuwi_vi8_plus_data,
 		.matches = {
@@ -1070,6 +1229,14 @@
 		},
 	},
 	{
+		/* CSL Panther Tab HD */
+		.driver_data = (void *)&csl_panther_tab_hd_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "CSL Computer GmbH & Co. KG"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "CSL Panther Tab HD"),
+		},
+	},
+	{
 		/* CUBE iwork8 Air */
 		.driver_data = (void *)&cube_iwork8_air_data,
 		.matches = {
@@ -1097,6 +1264,14 @@
 		},
 	},
 	{
+		/* DEXP Ursus KX210i */
+		.driver_data = (void *)&dexp_ursus_kx210i_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "INSYDE Corp."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "S107I"),
+		},
+	},
+	{
 		/* Digma Citi E200 */
 		.driver_data = (void *)&digma_citi_e200_data,
 		.matches = {
@@ -1187,6 +1362,17 @@
 		},
 	},
 	{
+		/* Jumper EZpad 6s Pro */
+		.driver_data = (void *)&jumper_ezpad_6_pro_b_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Jumper"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Ezpad"),
+			/* Above matches are too generic, add bios match */
+			DMI_MATCH(DMI_BIOS_VERSION, "E.WSA116_8.E1.042.bin"),
+			DMI_MATCH(DMI_BIOS_DATE, "01/08/2020"),
+		},
+	},
+	{
 		/* Jumper EZpad 6 m4 */
 		.driver_data = (void *)&jumper_ezpad_6_m4_data,
 		.matches = {
@@ -1216,6 +1402,18 @@
 		},
 	},
 	{
+		/* Juno Tablet */
+		.driver_data = (void *)&gdix1002_00_upside_down_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Default string"),
+			/* Both product- and board-name being "Default string" is somewhat rare */
+			DMI_MATCH(DMI_PRODUCT_NAME, "Default string"),
+			DMI_MATCH(DMI_BOARD_NAME, "Default string"),
+			/* Above matches are too generic, add partial bios-version match */
+			DMI_MATCH(DMI_BIOS_VERSION, "JP2V1."),
+		},
+	},
+	{
 		/* Mediacom WinPad 7.0 W700 (same hw as Wintron surftab 7") */
 		.driver_data = (void *)&trekstor_surftab_wintron70_data,
 		.matches = {
@@ -1337,6 +1535,14 @@
 		},
 	},
 	{
+		/* Positivo C4128B */
+		.driver_data = (void *)&positivo_c4128b_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Positivo Tecnologia SA"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "C4128B-1"),
+		},
+	},
+	{
 		/* Point of View mobii wintab p800w (v2.0) */
 		.driver_data = (void *)&pov_mobii_wintab_p800w_v20_data,
 		.matches = {
@@ -1380,6 +1586,35 @@
 		},
 	},
 	{
+		/* RCA Cambio W101 v2 */
+		/* https://github.com/onitake/gsl-firmware/discussions/193 */
+		.driver_data = (void *)&rca_cambio_w101_v2_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "RCA"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "W101SA23T1"),
+		},
+	},
+	{
+		/* RWC NANOTE P8 */
+		.driver_data = (void *)&rwc_nanote_p8_data,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Default string"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "AY07J"),
+			DMI_MATCH(DMI_PRODUCT_SKU, "0001")
+		},
+	},
+	{
+		/* RWC NANOTE NEXT */
+		.driver_data = (void *)&rwc_nanote_next_data,
+		.matches = {
+			DMI_MATCH(DMI_PRODUCT_NAME, "To be filled by O.E.M."),
+			DMI_MATCH(DMI_BOARD_NAME, "To be filled by O.E.M."),
+			DMI_MATCH(DMI_BOARD_VENDOR, "To be filled by O.E.M."),
+			/* Above matches are too generic, add bios-version match */
+			DMI_MATCH(DMI_BIOS_VERSION, "S8A70R100-V005"),
+		},
+	},
+	{
 		/* Schneider SCT101CTM */
 		.driver_data = (void *)&schneider_sct101ctm_data,
 		.matches = {
@@ -1388,6 +1623,15 @@
 		},
 	},
 	{
+		/* GlobalSpace SoLT IVW 11.6" */
+		.driver_data = (void *)&globalspace_solt_ivw116_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Globalspace Tech Pvt Ltd"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "SolTIVW"),
+			DMI_MATCH(DMI_PRODUCT_SKU, "PN20170413488"),
+		},
+	},
+	{
 		/* Techbite Arc 11.6 */
 		.driver_data = (void *)&techbite_arc_11_6_data,
 		.matches = {
@@ -1406,6 +1650,15 @@
 		},
 	},
 	{
+		/* Teclast X16 Plus */
+		.driver_data = (void *)&teclast_x16_plus_data,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "TECLAST"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Default string"),
+			DMI_MATCH(DMI_PRODUCT_SKU, "D3A5_A1"),
+		},
+	},
+	{
 		/* Teclast X3 Plus */
 		.driver_data = (void *)&teclast_x3_plus_data,
 		.matches = {
@@ -1563,7 +1816,7 @@
 	int error;
 
 	if (has_acpi_companion(dev) &&
-	    !strncmp(ts_data->acpi_name, client->name, I2C_NAME_SIZE)) {
+	    strstarts(client->name, ts_data->acpi_name)) {
 		error = device_create_managed_software_node(dev, ts_data->properties, NULL);
 		if (error)
 			dev_err(dev, "failed to add properties: %d\n", error);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/wireless-hotkey.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/wireless-hotkey.c
@@ -19,6 +19,7 @@
 MODULE_ALIAS("acpi*:HPQ6001:*");
 MODULE_ALIAS("acpi*:WSTADEF:*");
 MODULE_ALIAS("acpi*:AMDI0051:*");
+MODULE_ALIAS("acpi*:LGEX0815:*");
 
 static struct input_dev *wl_input_dev;
 
@@ -26,6 +27,7 @@
 	{"HPQ6001", 0},
 	{"WSTADEF", 0},
 	{"AMDI0051", 0},
+	{"LGEX0815", 0},
 	{"", 0},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/platform/x86/wmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/platform/x86/wmi.c
@@ -39,7 +39,7 @@
 static LIST_HEAD(wmi_block_list);
 
 struct guid_block {
-	char guid[16];
+	guid_t guid;
 	union {
 		char object_id[2];
 		struct {
@@ -51,6 +51,11 @@
 	u8 flags;
 };
 
+enum {	/* wmi_block flags */
+	WMI_READ_TAKES_NO_ARGS,
+	WMI_PROBED,
+};
+
 struct wmi_block {
 	struct wmi_device dev;
 	struct list_head list;
@@ -61,8 +66,7 @@
 	wmi_notify_handler handler;
 	void *handler_data;
 	u64 req_buf_size;
-
-	bool read_takes_no_args;
+	unsigned long flags;
 };
 
 
@@ -95,6 +99,12 @@
 };
 MODULE_DEVICE_TABLE(acpi, wmi_device_ids);
 
+/* allow duplicate GUIDs as these device drivers use struct wmi_driver */
+static const char * const allow_duplicates[] = {
+	"05901221-D566-11D1-B2F0-00A0C9062910",	/* wmi-bmof */
+	NULL
+};
+
 static struct platform_driver acpi_wmi_driver = {
 	.driver = {
 		.name = "acpi-wmi",
@@ -120,7 +130,7 @@
 	list_for_each_entry(wblock, &wmi_block_list, list) {
 		block = &wblock->gblock;
 
-		if (memcmp(block->guid, &guid_input, 16) == 0) {
+		if (guid_equal(&block->guid, &guid_input)) {
 			if (out)
 				*out = wblock;
 			return true;
@@ -129,11 +139,20 @@
 	return false;
 }
 
+static bool guid_parse_and_compare(const char *string, const guid_t *guid)
+{
+	guid_t guid_input;
+
+	if (guid_parse(string, &guid_input))
+		return false;
+
+	return guid_equal(&guid_input, guid);
+}
+
 static const void *find_guid_context(struct wmi_block *wblock,
 				      struct wmi_driver *wdriver)
 {
 	const struct wmi_device_id *id;
-	guid_t guid_input;
 
 	if (wblock == NULL || wdriver == NULL)
 		return NULL;
@@ -142,9 +161,7 @@
 
 	id = wdriver->id_table;
 	while (*id->guid_string) {
-		if (guid_parse(id->guid_string, &guid_input))
-			continue;
-		if (!memcmp(wblock->gblock.guid, &guid_input, 16))
+		if (guid_parse_and_compare(id->guid_string, &wblock->gblock.guid))
 			return id->context;
 		id++;
 	}
@@ -177,7 +194,7 @@
 
 static acpi_status wmi_method_enable(struct wmi_block *wblock, int enable)
 {
-	struct guid_block *block = NULL;
+	struct guid_block *block;
 	char method[5];
 	acpi_status status;
 	acpi_handle handle;
@@ -251,8 +268,8 @@
 acpi_status wmidev_evaluate_method(struct wmi_device *wdev, u8 instance,
 	u32 method_id, const struct acpi_buffer *in, struct acpi_buffer *out)
 {
-	struct guid_block *block = NULL;
-	struct wmi_block *wblock = NULL;
+	struct guid_block *block;
+	struct wmi_block *wblock;
 	acpi_handle handle;
 	acpi_status status;
 	struct acpi_object_list input;
@@ -299,7 +316,7 @@
 static acpi_status __query_block(struct wmi_block *wblock, u8 instance,
 				 struct acpi_buffer *out)
 {
-	struct guid_block *block = NULL;
+	struct guid_block *block;
 	acpi_handle handle;
 	acpi_status status, wc_status = AE_ERROR;
 	struct acpi_object_list input;
@@ -325,7 +342,7 @@
 	wq_params[0].type = ACPI_TYPE_INTEGER;
 	wq_params[0].integer.value = instance;
 
-	if (instance == 0 && wblock->read_takes_no_args)
+	if (instance == 0 && test_bit(WMI_READ_TAKES_NO_ARGS, &wblock->flags))
 		input.count = 0;
 
 	/*
@@ -353,7 +370,14 @@
 	 * the WQxx method failed - we should disable collection anyway.
 	 */
 	if ((block->flags & ACPI_WMI_EXPENSIVE) && ACPI_SUCCESS(wc_status)) {
-		status = acpi_execute_simple_method(handle, wc_method, 0);
+		/*
+		 * Ignore whether this WCxx call succeeds or not since
+		 * the previously executed WQxx method call might have
+		 * succeeded, and returning the failing status code
+		 * of this call would throw away the result of the WQxx
+		 * call, potentially leaking memory.
+		 */
+		acpi_execute_simple_method(handle, wc_method, 0);
 	}
 
 	return status;
@@ -405,8 +429,8 @@
 acpi_status wmi_set_block(const char *guid_string, u8 instance,
 			  const struct acpi_buffer *in)
 {
-	struct guid_block *block = NULL;
 	struct wmi_block *wblock = NULL;
+	struct guid_block *block;
 	acpi_handle handle;
 	struct acpi_object_list input;
 	union acpi_object params[2];
@@ -449,7 +473,7 @@
 
 static void wmi_dump_wdg(const struct guid_block *g)
 {
-	pr_info("%pUL:\n", g->guid);
+	pr_info("%pUL:\n", &g->guid);
 	if (g->flags & ACPI_WMI_EVENT)
 		pr_info("\tnotify_id: 0x%02X\n", g->notify_id);
 	else
@@ -531,7 +555,7 @@
 	list_for_each_entry(block, &wmi_block_list, list) {
 		acpi_status wmi_status;
 
-		if (memcmp(block->gblock.guid, &guid_input, 16) == 0) {
+		if (guid_equal(&block->gblock.guid, &guid_input)) {
 			if (block->handler &&
 			    block->handler != wmi_notify_debug)
 				return AE_ALREADY_ACQUIRED;
@@ -571,7 +595,7 @@
 	list_for_each_entry(block, &wmi_block_list, list) {
 		acpi_status wmi_status;
 
-		if (memcmp(block->gblock.guid, &guid_input, 16) == 0) {
+		if (guid_equal(&block->gblock.guid, &guid_input)) {
 			if (!block->handler ||
 			    block->handler == wmi_notify_debug)
 				return AE_NULL_ENTRY;
@@ -607,7 +631,6 @@
 {
 	struct acpi_object_list input;
 	union acpi_object params[1];
-	struct guid_block *gblock;
 	struct wmi_block *wblock;
 
 	input.count = 1;
@@ -616,7 +639,7 @@
 	params[0].integer.value = event;
 
 	list_for_each_entry(wblock, &wmi_block_list, list) {
-		gblock = &wblock->gblock;
+		struct guid_block *gblock = &wblock->gblock;
 
 		if ((gblock->flags & ACPI_WMI_EVENT) &&
 			(gblock->notify_id == event))
@@ -669,6 +692,11 @@
 	return container_of(dev, struct wmi_device, dev);
 }
 
+static inline struct wmi_driver *drv_to_wdrv(struct device_driver *drv)
+{
+	return container_of(drv, struct wmi_driver, driver);
+}
+
 /*
  * sysfs interface
  */
@@ -677,7 +705,7 @@
 {
 	struct wmi_block *wblock = dev_to_wblock(dev);
 
-	return sprintf(buf, "wmi:%pUL\n", wblock->gblock.guid);
+	return sprintf(buf, "wmi:%pUL\n", &wblock->gblock.guid);
 }
 static DEVICE_ATTR_RO(modalias);
 
@@ -686,7 +714,7 @@
 {
 	struct wmi_block *wblock = dev_to_wblock(dev);
 
-	return sprintf(buf, "%pUL\n", wblock->gblock.guid);
+	return sprintf(buf, "%pUL\n", &wblock->gblock.guid);
 }
 static DEVICE_ATTR_RO(guid);
 
@@ -769,10 +797,10 @@
 {
 	struct wmi_block *wblock = dev_to_wblock(dev);
 
-	if (add_uevent_var(env, "MODALIAS=wmi:%pUL", wblock->gblock.guid))
+	if (add_uevent_var(env, "MODALIAS=wmi:%pUL", &wblock->gblock.guid))
 		return -ENOMEM;
 
-	if (add_uevent_var(env, "WMI_GUID=%pUL", wblock->gblock.guid))
+	if (add_uevent_var(env, "WMI_GUID=%pUL", &wblock->gblock.guid))
 		return -ENOMEM;
 
 	return 0;
@@ -787,8 +815,7 @@
 
 static int wmi_dev_match(struct device *dev, struct device_driver *driver)
 {
-	struct wmi_driver *wmi_driver =
-		container_of(driver, struct wmi_driver, driver);
+	struct wmi_driver *wmi_driver = drv_to_wdrv(driver);
 	struct wmi_block *wblock = dev_to_wblock(dev);
 	const struct wmi_device_id *id = wmi_driver->id_table;
 
@@ -796,11 +823,7 @@
 		return 0;
 
 	while (*id->guid_string) {
-		guid_t driver_guid;
-
-		if (WARN_ON(guid_parse(id->guid_string, &driver_guid)))
-			continue;
-		if (!memcmp(&driver_guid, wblock->gblock.guid, 16))
+		if (guid_parse_and_compare(id->guid_string, &wblock->gblock.guid))
 			return 1;
 
 		id++;
@@ -810,21 +833,13 @@
 }
 static int wmi_char_open(struct inode *inode, struct file *filp)
 {
-	const char *driver_name = filp->f_path.dentry->d_iname;
-	struct wmi_block *wblock = NULL;
-	struct wmi_block *next = NULL;
-
-	list_for_each_entry_safe(wblock, next, &wmi_block_list, list) {
-		if (!wblock->dev.dev.driver)
-			continue;
-		if (strcmp(driver_name, wblock->dev.dev.driver->name) == 0) {
-			filp->private_data = wblock;
-			break;
-		}
-	}
+	/*
+	 * The miscdevice already stores a pointer to itself
+	 * inside filp->private_data
+	 */
+	struct wmi_block *wblock = container_of(filp->private_data, struct wmi_block, char_dev);
 
-	if (!filp->private_data)
-		return -ENODEV;
+	filp->private_data = wblock;
 
 	return nonseekable_open(inode, filp);
 }
@@ -844,8 +859,8 @@
 	struct wmi_ioctl_buffer __user *input =
 		(struct wmi_ioctl_buffer __user *) arg;
 	struct wmi_block *wblock = filp->private_data;
-	struct wmi_ioctl_buffer *buf = NULL;
-	struct wmi_driver *wdriver = NULL;
+	struct wmi_ioctl_buffer *buf;
+	struct wmi_driver *wdriver;
 	int ret;
 
 	if (_IOC_TYPE(cmd) != WMI_IOC)
@@ -885,8 +900,7 @@
 	}
 
 	/* let the driver do any filtering and do the call */
-	wdriver = container_of(wblock->dev.dev.driver,
-			       struct wmi_driver, driver);
+	wdriver = drv_to_wdrv(wblock->dev.dev.driver);
 	if (!try_module_get(wdriver->driver.owner)) {
 		ret = -EBUSY;
 		goto out_ioctl;
@@ -919,8 +933,7 @@
 static int wmi_dev_probe(struct device *dev)
 {
 	struct wmi_block *wblock = dev_to_wblock(dev);
-	struct wmi_driver *wdriver =
-		container_of(dev->driver, struct wmi_driver, driver);
+	struct wmi_driver *wdriver = drv_to_wdrv(dev->driver);
 	int ret = 0;
 	char *buf;
 
@@ -968,6 +981,7 @@
 		}
 	}
 
+	set_bit(WMI_PROBED, &wblock->flags);
 	return 0;
 
 probe_misc_failure:
@@ -983,8 +997,9 @@
 static void wmi_dev_remove(struct device *dev)
 {
 	struct wmi_block *wblock = dev_to_wblock(dev);
-	struct wmi_driver *wdriver =
-		container_of(dev->driver, struct wmi_driver, driver);
+	struct wmi_driver *wdriver = drv_to_wdrv(dev->driver);
+
+	clear_bit(WMI_PROBED, &wblock->flags);
 
 	if (wdriver->filter_callback) {
 		misc_deregister(&wblock->char_dev);
@@ -1030,21 +1045,38 @@
 	.release = wmi_dev_release,
 };
 
+/*
+ * _WDG is a static list that is only parsed at startup,
+ * so it's safe to count entries without extra protection.
+ */
+static int guid_count(const guid_t *guid)
+{
+	struct wmi_block *wblock;
+	int count = 0;
+
+	list_for_each_entry(wblock, &wmi_block_list, list) {
+		if (guid_equal(&wblock->gblock.guid, guid))
+			count++;
+	}
+
+	return count;
+}
+
 static int wmi_create_device(struct device *wmi_bus_dev,
-			     const struct guid_block *gblock,
 			     struct wmi_block *wblock,
 			     struct acpi_device *device)
 {
 	struct acpi_device_info *info;
 	char method[5];
 	int result;
+	uint count;
 
-	if (gblock->flags & ACPI_WMI_EVENT) {
+	if (wblock->gblock.flags & ACPI_WMI_EVENT) {
 		wblock->dev.dev.type = &wmi_type_event;
 		goto out_init;
 	}
 
-	if (gblock->flags & ACPI_WMI_METHOD) {
+	if (wblock->gblock.flags & ACPI_WMI_METHOD) {
 		wblock->dev.dev.type = &wmi_type_method;
 		mutex_init(&wblock->char_mutex);
 		goto out_init;
@@ -1079,7 +1111,7 @@
 	 * laptops, WQxx may not be a method at all.)
 	 */
 	if (info->type != ACPI_TYPE_METHOD || info->param_count == 0)
-		wblock->read_takes_no_args = true;
+		set_bit(WMI_READ_TAKES_NO_ARGS, &wblock->flags);
 
 	kfree(info);
 
@@ -1094,7 +1126,11 @@
 	wblock->dev.dev.bus = &wmi_bus_type;
 	wblock->dev.dev.parent = wmi_bus_dev;
 
-	dev_set_name(&wblock->dev.dev, "%pUL", gblock->guid);
+	count = guid_count(&wblock->gblock.guid);
+	if (count)
+		dev_set_name(&wblock->dev.dev, "%pUL-%d", &wblock->gblock.guid, count);
+	else
+		dev_set_name(&wblock->dev.dev, "%pUL", &wblock->gblock.guid);
 
 	device_initialize(&wblock->dev.dev);
 
@@ -1114,12 +1150,23 @@
 	}
 }
 
-static bool guid_already_parsed(struct acpi_device *device, const u8 *guid)
+static bool guid_already_parsed_for_legacy(struct acpi_device *device, const guid_t *guid)
 {
 	struct wmi_block *wblock;
 
 	list_for_each_entry(wblock, &wmi_block_list, list) {
-		if (memcmp(wblock->gblock.guid, guid, 16) == 0) {
+		int i;
+
+		/* skip warning and register if we know the driver will use struct wmi_driver */
+		for (i = 0; allow_duplicates[i] != NULL; i++) {
+			guid_t tmp;
+
+			if (guid_parse(allow_duplicates[i], &tmp))
+				continue;
+			if (guid_equal(&tmp, guid))
+				return false;
+		}
+		if (guid_equal(&wblock->gblock.guid, guid)) {
 			/*
 			 * Because we historically didn't track the relationship
 			 * between GUIDs and ACPI nodes, we don't know whether
@@ -1145,8 +1192,8 @@
 	struct wmi_block *wblock, *next;
 	union acpi_object *obj;
 	acpi_status status;
-	int retval = 0;
 	u32 i, total;
+	int retval;
 
 	status = acpi_evaluate_object(device->handle, "_WDG", NULL, &out);
 	if (ACPI_FAILURE(status))
@@ -1157,8 +1204,8 @@
 		return -ENXIO;
 
 	if (obj->type != ACPI_TYPE_BUFFER) {
-		retval = -ENXIO;
-		goto out_free_pointer;
+		kfree(obj);
+		return -ENXIO;
 	}
 
 	gblock = (const struct guid_block *)obj->buffer.pointer;
@@ -1168,25 +1215,24 @@
 		if (debug_dump_wdg)
 			wmi_dump_wdg(&gblock[i]);
 
-		/*
-		 * Some WMI devices, like those for nVidia hooks, have a
-		 * duplicate GUID. It's not clear what we should do in this
-		 * case yet, so for now, we'll just ignore the duplicate
-		 * for device creation.
-		 */
-		if (guid_already_parsed(device, gblock[i].guid))
+		if (!gblock[i].instance_count) {
+			dev_info(wmi_bus_dev, FW_INFO "%pUL has zero instances\n", &gblock[i].guid);
+			continue;
+		}
+
+		if (guid_already_parsed_for_legacy(device, &gblock[i].guid))
 			continue;
 
 		wblock = kzalloc(sizeof(struct wmi_block), GFP_KERNEL);
 		if (!wblock) {
-			retval = -ENOMEM;
-			break;
+			dev_err(wmi_bus_dev, "Failed to allocate %pUL\n", &gblock[i].guid);
+			continue;
 		}
 
 		wblock->acpi_device = device;
 		wblock->gblock = gblock[i];
 
-		retval = wmi_create_device(wmi_bus_dev, &gblock[i], wblock, device);
+		retval = wmi_create_device(wmi_bus_dev, wblock, device);
 		if (retval) {
 			kfree(wblock);
 			continue;
@@ -1211,7 +1257,7 @@
 		retval = device_add(&wblock->dev.dev);
 		if (retval) {
 			dev_err(wmi_bus_dev, "failed to register %pUL\n",
-				wblock->gblock.guid);
+				&wblock->gblock.guid);
 			if (debug_event)
 				wmi_method_enable(wblock, 0);
 			list_del(&wblock->list);
@@ -1219,9 +1265,9 @@
 		}
 	}
 
-out_free_pointer:
-	kfree(out.pointer);
-	return retval;
+	kfree(obj);
+
+	return 0;
 }
 
 /*
@@ -1268,12 +1314,11 @@
 static void acpi_wmi_notify_handler(acpi_handle handle, u32 event,
 				    void *context)
 {
-	struct guid_block *block;
 	struct wmi_block *wblock;
 	bool found_it = false;
 
 	list_for_each_entry(wblock, &wmi_block_list, list) {
-		block = &wblock->gblock;
+		struct guid_block *block = &wblock->gblock;
 
 		if (wblock->acpi_device->handle == handle &&
 		    (block->flags & ACPI_WMI_EVENT) &&
@@ -1288,16 +1333,13 @@
 		return;
 
 	/* If a driver is bound, then notify the driver. */
-	if (wblock->dev.dev.driver) {
-		struct wmi_driver *driver;
+	if (test_bit(WMI_PROBED, &wblock->flags) && wblock->dev.dev.driver) {
+		struct wmi_driver *driver = drv_to_wdrv(wblock->dev.dev.driver);
 		struct acpi_object_list input;
 		union acpi_object params[1];
 		struct acpi_buffer evdata = { ACPI_ALLOCATE_BUFFER, NULL };
 		acpi_status status;
 
-		driver = container_of(wblock->dev.dev.driver,
-				      struct wmi_driver, driver);
-
 		input.count = 1;
 		input.pointer = params;
 		params[0].type = ACPI_TYPE_INTEGER;
@@ -1322,7 +1364,7 @@
 	}
 
 	if (debug_event)
-		pr_info("DEBUG Event GUID: %pUL\n", wblock->gblock.guid);
+		pr_info("DEBUG Event GUID: %pUL\n", &wblock->gblock.guid);
 
 	acpi_bus_generate_netlink_event(
 		wblock->acpi_device->pnp.device_class,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pnp/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pnp/core.c
@@ -148,14 +148,14 @@
 	dev->dev.coherent_dma_mask = dev->dma_mask;
 	dev->dev.release = &pnp_release_device;
 
-	dev_set_name(&dev->dev, "%02x:%02x", dev->protocol->number, dev->number);
-
 	dev_id = pnp_add_id(dev, pnpid);
 	if (!dev_id) {
 		kfree(dev);
 		return NULL;
 	}
 
+	dev_set_name(&dev->dev, "%02x:%02x", dev->protocol->number, dev->number);
+
 	return dev;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pnp/isapnp/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pnp/isapnp/core.c
@@ -27,6 +27,7 @@
 #include <linux/init.h>
 #include <linux/isapnp.h>
 #include <linux/mutex.h>
+#include <linux/async.h>
 #include <asm/io.h>
 
 #include "../base.h"
@@ -950,7 +951,7 @@
 	.disable = isapnp_disable_resources,
 };
 
-static int __init isapnp_init(void)
+static int __init real_isapnp_init(void)
 {
 	int cards;
 	struct pnp_card *card;
@@ -1044,6 +1045,16 @@
 	return 0;
 }
 
+static void __init async_isapnp_init(void *unused, async_cookie_t cookie)
+{
+	(void)real_isapnp_init();
+}
+
+static int __init isapnp_init(void)
+{
+	async_schedule(async_isapnp_init, NULL);
+	return 0;
+}
 device_initcall(isapnp_init);
 
 /* format is: noisapnp */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pnp/pnpacpi/rsparser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pnp/pnpacpi/rsparser.c
@@ -151,13 +151,13 @@
 static void pnpacpi_parse_allocated_vendor(struct pnp_dev *dev,
 				    struct acpi_resource_vendor_typed *vendor)
 {
-	if (vendor_resource_matches(dev, vendor, &hp_ccsr_uuid, 16)) {
-		u64 start, length;
+	struct { u64 start, length; } range;
 
-		memcpy(&start, vendor->byte_data, sizeof(start));
-		memcpy(&length, vendor->byte_data + 8, sizeof(length));
-
-		pnp_add_mem_resource(dev, start, start + length - 1, 0);
+	if (vendor_resource_matches(dev, vendor, &hp_ccsr_uuid,
+				    sizeof(range))) {
+		memcpy(&range, vendor->byte_data, sizeof(range));
+		pnp_add_mem_resource(dev, range.start, range.start +
+				     range.length - 1, 0);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/reset/arm-versatile-reboot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/reset/arm-versatile-reboot.c
@@ -146,6 +146,7 @@
 	versatile_reboot_type = (enum versatile_reboot)reboot_id->data;
 
 	syscon_regmap = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (IS_ERR(syscon_regmap))
 		return PTR_ERR(syscon_regmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/reset/at91-reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/reset/at91-reset.c
@@ -193,7 +193,7 @@
 		return -ENOMEM;
 
 	reset->rstc_base = devm_of_iomap(&pdev->dev, pdev->dev.of_node, 0, NULL);
-	if (!reset->rstc_base) {
+	if (IS_ERR(reset->rstc_base)) {
 		dev_err(&pdev->dev, "Could not map reset controller address\n");
 		return -ENODEV;
 	}
@@ -203,7 +203,7 @@
 		for_each_matching_node_and_match(np, at91_ramc_of_match, &match) {
 			reset->ramc_lpr = (u32)match->data;
 			reset->ramc_base[idx] = devm_of_iomap(&pdev->dev, np, 0, NULL);
-			if (!reset->ramc_base[idx]) {
+			if (IS_ERR(reset->ramc_base[idx])) {
 				dev_err(&pdev->dev, "Could not map ram controller address\n");
 				of_node_put(np);
 				return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/reset/brcmstb-reboot.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/reset/brcmstb-reboot.c
@@ -72,9 +72,6 @@
 		return NOTIFY_DONE;
 	}
 
-	while (1)
-		;
-
 	return NOTIFY_DONE;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/reset/gemini-poweroff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/reset/gemini-poweroff.c
@@ -107,8 +107,8 @@
 		return PTR_ERR(gpw->base);
 
 	irq = platform_get_irq(pdev, 0);
-	if (!irq)
-		return -EINVAL;
+	if (irq < 0)
+		return irq;
 
 	gpw->dev = dev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/reset/ltc2952-poweroff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/reset/ltc2952-poweroff.c
@@ -161,8 +161,8 @@
 
 static void ltc2952_poweroff_default(struct ltc2952_poweroff *data)
 {
-	data->wde_interval = 300L * 1E6L;
-	data->trigger_delay = ktime_set(2, 500L*1E6L);
+	data->wde_interval = 300L * NSEC_PER_MSEC;
+	data->trigger_delay = ktime_set(2, 500L * NSEC_PER_MSEC);
 
 	hrtimer_init(&data->timer_trigger, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
 	data->timer_trigger.function = ltc2952_poweroff_timer_trigger;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/reset/mt6323-poweroff.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/reset/mt6323-poweroff.c
@@ -57,6 +57,9 @@
 		return -ENOMEM;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
+
 	pwrc->base = res->start;
 	pwrc->regmap = mt6397_chip->regmap;
 	pwrc->dev = &pdev->dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/ab8500_btemp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/ab8500_btemp.c
@@ -902,10 +902,8 @@
  */
 static void ab8500_btemp_external_power_changed(struct power_supply *psy)
 {
-	struct ab8500_btemp *di = power_supply_get_drvdata(psy);
-
-	class_for_each_device(power_supply_class, NULL,
-		di->btemp_psy, ab8500_btemp_get_ext_psy_data);
+	class_for_each_device(power_supply_class, NULL, psy,
+			      ab8500_btemp_get_ext_psy_data);
 }
 
 /* ab8500 btemp driver interrupts and their respective isr */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/ab8500_chargalg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/ab8500_chargalg.c
@@ -2019,11 +2019,11 @@
 	psy_cfg.drv_data = di;
 
 	/* Initilialize safety timer */
-	hrtimer_init(&di->safety_timer, CLOCK_REALTIME, HRTIMER_MODE_ABS);
+	hrtimer_init(&di->safety_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
 	di->safety_timer.function = ab8500_chargalg_safety_timer_expired;
 
 	/* Initilialize maintenance timer */
-	hrtimer_init(&di->maintenance_timer, CLOCK_REALTIME, HRTIMER_MODE_ABS);
+	hrtimer_init(&di->maintenance_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
 	di->maintenance_timer.function =
 		ab8500_chargalg_maintenance_timer_expired;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/ab8500_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/ab8500_charger.c
@@ -3726,7 +3726,14 @@
 	if (ret)
 		return ret;
 
-	return platform_driver_register(&ab8500_charger_driver);
+	ret = platform_driver_register(&ab8500_charger_driver);
+	if (ret) {
+		platform_unregister_drivers(ab8500_charger_component_drivers,
+				ARRAY_SIZE(ab8500_charger_component_drivers));
+		return ret;
+	}
+
+	return 0;
 }
 
 static void __exit ab8500_charger_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/ab8500_fg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/ab8500_fg.c
@@ -2384,10 +2384,8 @@
  */
 static void ab8500_fg_external_power_changed(struct power_supply *psy)
 {
-	struct ab8500_fg *di = power_supply_get_drvdata(psy);
-
-	class_for_each_device(power_supply_class, NULL,
-		di->fg_psy, ab8500_fg_get_ext_psy_data);
+	class_for_each_device(power_supply_class, NULL, psy,
+			      ab8500_fg_get_ext_psy_data);
 }
 
 /**
@@ -2545,8 +2543,10 @@
 	ret = kobject_init_and_add(&di->fg_kobject,
 		&ab8500_fg_ktype,
 		NULL, "battery");
-	if (ret < 0)
+	if (ret < 0) {
+		kobject_put(&di->fg_kobject);
 		dev_err(di->dev, "failed to create sysfs entry\n");
+	}
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/adp5061.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/adp5061.c
@@ -427,11 +427,11 @@
 	if (ret < 0)
 		return ret;
 
-	chg_type = adp5061_chg_type[ADP5061_CHG_STATUS_1_CHG_STATUS(status1)];
-	if (chg_type > ADP5061_CHG_FAST_CV)
+	chg_type = ADP5061_CHG_STATUS_1_CHG_STATUS(status1);
+	if (chg_type >= ARRAY_SIZE(adp5061_chg_type))
 		val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
 	else
-		val->intval = chg_type;
+		val->intval = adp5061_chg_type[chg_type];
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/axp20x_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/axp20x_battery.c
@@ -186,7 +186,6 @@
 				   union power_supply_propval *val)
 {
 	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
-	struct iio_channel *chan;
 	int ret = 0, reg, val1;
 
 	switch (psp) {
@@ -266,12 +265,12 @@
 		if (ret)
 			return ret;
 
-		if (reg & AXP20X_PWR_STATUS_BAT_CHARGING)
-			chan = axp20x_batt->batt_chrg_i;
-		else
-			chan = axp20x_batt->batt_dischrg_i;
-
-		ret = iio_read_channel_processed(chan, &val->intval);
+		if (reg & AXP20X_PWR_STATUS_BAT_CHARGING) {
+			ret = iio_read_channel_processed(axp20x_batt->batt_chrg_i, &val->intval);
+		} else {
+			ret = iio_read_channel_processed(axp20x_batt->batt_dischrg_i, &val1);
+			val->intval = -val1;
+		}
 		if (ret)
 			return ret;
 
@@ -305,11 +304,11 @@
 		val->intval = reg & AXP209_FG_PERCENT;
 		break;
 
-	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 		return axp20x_batt->data->get_max_voltage(axp20x_batt,
 							  &val->intval);
 
-	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
 		ret = regmap_read(axp20x_batt->regmap, AXP20X_V_OFF, &reg);
 		if (ret)
 			return ret;
@@ -457,10 +456,10 @@
 	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
 
 	switch (psp) {
-	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
 		return axp20x_set_voltage_min_design(axp20x_batt, val->intval);
 
-	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 		return axp20x_batt->data->set_max_voltage(axp20x_batt, val->intval);
 
 	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
@@ -495,8 +494,8 @@
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
 	POWER_SUPPLY_PROP_HEALTH,
-	POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
-	POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+	POWER_SUPPLY_PROP_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
 	POWER_SUPPLY_PROP_CAPACITY,
 };
 
@@ -504,8 +503,8 @@
 					 enum power_supply_property psp)
 {
 	return psp == POWER_SUPPLY_PROP_STATUS ||
-	       psp == POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN ||
-	       psp == POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MAX ||
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT ||
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/axp288_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/axp288_charger.c
@@ -41,11 +41,11 @@
 #define VBUS_ISPOUT_CUR_LIM_1500MA	0x1	/* 1500mA */
 #define VBUS_ISPOUT_CUR_LIM_2000MA	0x2	/* 2000mA */
 #define VBUS_ISPOUT_CUR_NO_LIM		0x3	/* 2500mA */
-#define VBUS_ISPOUT_VHOLD_SET_MASK	0x31
+#define VBUS_ISPOUT_VHOLD_SET_MASK	0x38
 #define VBUS_ISPOUT_VHOLD_SET_BIT_POS	0x3
 #define VBUS_ISPOUT_VHOLD_SET_OFFSET	4000	/* 4000mV */
 #define VBUS_ISPOUT_VHOLD_SET_LSB_RES	100	/* 100mV */
-#define VBUS_ISPOUT_VHOLD_SET_4300MV	0x3	/* 4300mV */
+#define VBUS_ISPOUT_VHOLD_SET_4400MV	0x4	/* 4400mV */
 #define VBUS_ISPOUT_VBUS_PATH_DIS	BIT(7)
 
 #define CHRG_CCCV_CC_MASK		0xf		/* 4 bits */
@@ -168,18 +168,18 @@
 	u8 reg_val;
 	int ret;
 
-	if (cv <= CV_4100MV) {
-		reg_val = CHRG_CCCV_CV_4100MV;
-		cv = CV_4100MV;
-	} else if (cv <= CV_4150MV) {
-		reg_val = CHRG_CCCV_CV_4150MV;
-		cv = CV_4150MV;
-	} else if (cv <= CV_4200MV) {
+	if (cv >= CV_4350MV) {
+		reg_val = CHRG_CCCV_CV_4350MV;
+		cv = CV_4350MV;
+	} else if (cv >= CV_4200MV) {
 		reg_val = CHRG_CCCV_CV_4200MV;
 		cv = CV_4200MV;
+	} else if (cv >= CV_4150MV) {
+		reg_val = CHRG_CCCV_CV_4150MV;
+		cv = CV_4150MV;
 	} else {
-		reg_val = CHRG_CCCV_CV_4350MV;
-		cv = CV_4350MV;
+		reg_val = CHRG_CCCV_CV_4100MV;
+		cv = CV_4100MV;
 	}
 
 	reg_val = reg_val << CHRG_CCCV_CV_BIT_POS;
@@ -371,8 +371,8 @@
 			dev_warn(&info->pdev->dev, "set charge current failed\n");
 		break;
 	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
-		scaled_val = min(val->intval, info->max_cv);
-		scaled_val = DIV_ROUND_CLOSEST(scaled_val, 1000);
+		scaled_val = DIV_ROUND_CLOSEST(val->intval, 1000);
+		scaled_val = min(scaled_val, info->max_cv);
 		ret = axp288_charger_set_cv(info, scaled_val);
 		if (ret < 0)
 			dev_warn(&info->pdev->dev, "set charge voltage failed\n");
@@ -744,6 +744,16 @@
 		ret = axp288_charger_vbus_path_select(info, true);
 		if (ret < 0)
 			return ret;
+	} else {
+		/* Set Vhold to the factory default / recommended 4.4V */
+		val = VBUS_ISPOUT_VHOLD_SET_4400MV << VBUS_ISPOUT_VHOLD_SET_BIT_POS;
+		ret = regmap_update_bits(info->regmap, AXP20X_VBUS_IPSOUT_MGMT,
+					 VBUS_ISPOUT_VHOLD_SET_MASK, val);
+		if (ret < 0) {
+			dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
+				AXP20X_VBUS_IPSOUT_MGMT, ret);
+			return ret;
+		}
 	}
 
 	/* Read current charge voltage and current limit */
@@ -822,17 +832,20 @@
 	info->regmap_irqc = axp20x->regmap_irqc;
 
 	info->cable.edev = extcon_get_extcon_dev(AXP288_EXTCON_DEV_NAME);
-	if (info->cable.edev == NULL) {
-		dev_dbg(dev, "%s is not ready, probe deferred\n",
-			AXP288_EXTCON_DEV_NAME);
-		return -EPROBE_DEFER;
+	if (IS_ERR(info->cable.edev)) {
+		dev_err_probe(dev, PTR_ERR(info->cable.edev),
+			      "extcon_get_extcon_dev(%s) failed\n",
+			      AXP288_EXTCON_DEV_NAME);
+		return PTR_ERR(info->cable.edev);
 	}
 
 	if (acpi_dev_present(USB_HOST_EXTCON_HID, NULL, -1)) {
 		info->otg.cable = extcon_get_extcon_dev(USB_HOST_EXTCON_NAME);
-		if (info->otg.cable == NULL) {
-			dev_dbg(dev, "EXTCON_USB_HOST is not ready, probe deferred\n");
-			return -EPROBE_DEFER;
+		if (IS_ERR(info->otg.cable)) {
+			dev_err_probe(dev, PTR_ERR(info->otg.cable),
+				      "extcon_get_extcon_dev(%s) failed\n",
+				      USB_HOST_EXTCON_NAME);
+			return PTR_ERR(info->otg.cable);
 		}
 		dev_info(dev, "Using " USB_HOST_EXTCON_HID " extcon for usb-id\n");
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/axp288_fuel_gauge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/axp288_fuel_gauge.c
@@ -605,7 +605,6 @@
 			DMI_MATCH(DMI_BOARD_NAME, "T3 MRD"),
 			DMI_MATCH(DMI_CHASSIS_TYPE, "3"),
 			DMI_MATCH(DMI_BIOS_VENDOR, "American Megatrends Inc."),
-			DMI_MATCH(DMI_BIOS_VERSION, "5.11"),
 		},
 	},
 	{}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/bq24190_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/bq24190_charger.c
@@ -39,6 +39,7 @@
 #define BQ24190_REG_POC_CHG_CONFIG_DISABLE		0x0
 #define BQ24190_REG_POC_CHG_CONFIG_CHARGE		0x1
 #define BQ24190_REG_POC_CHG_CONFIG_OTG			0x2
+#define BQ24190_REG_POC_CHG_CONFIG_OTG_ALT		0x3
 #define BQ24190_REG_POC_SYS_MIN_MASK		(BIT(3) | BIT(2) | BIT(1))
 #define BQ24190_REG_POC_SYS_MIN_SHIFT		1
 #define BQ24190_REG_POC_SYS_MIN_MIN			3000
@@ -445,11 +446,9 @@
 	if (!info)
 		return -EINVAL;
 
-	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	ret = bq24190_read_mask(bdi, info->reg, info->mask, info->shift, &v);
 	if (ret)
@@ -480,11 +479,9 @@
 	if (ret < 0)
 		return ret;
 
-	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	ret = bq24190_write_mask(bdi, info->reg, info->mask, info->shift, v);
 	if (ret)
@@ -503,10 +500,9 @@
 	struct bq24190_dev_info *bdi = rdev_get_drvdata(dev);
 	int ret;
 
-	ret = pm_runtime_get_sync(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
 	if (ret < 0) {
 		dev_warn(bdi->dev, "pm_runtime_get failed: %i\n", ret);
-		pm_runtime_put_noidle(bdi->dev);
 		return ret;
 	}
 
@@ -536,10 +532,9 @@
 	int ret;
 	u8 val;
 
-	ret = pm_runtime_get_sync(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
 	if (ret < 0) {
 		dev_warn(bdi->dev, "pm_runtime_get failed: %i\n", ret);
-		pm_runtime_put_noidle(bdi->dev);
 		return ret;
 	}
 
@@ -550,7 +545,11 @@
 	pm_runtime_mark_last_busy(bdi->dev);
 	pm_runtime_put_autosuspend(bdi->dev);
 
-	return ret ? ret : val == BQ24190_REG_POC_CHG_CONFIG_OTG;
+	if (ret)
+		return ret;
+
+	return (val == BQ24190_REG_POC_CHG_CONFIG_OTG ||
+		val == BQ24190_REG_POC_CHG_CONFIG_OTG_ALT);
 }
 
 static const struct regulator_ops bq24190_vbus_ops = {
@@ -1076,11 +1075,9 @@
 
 	dev_dbg(bdi->dev, "prop: %d\n", psp);
 
-	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_CHARGE_TYPE:
@@ -1150,11 +1147,9 @@
 
 	dev_dbg(bdi->dev, "prop: %d\n", psp);
 
-	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_ONLINE:
@@ -1206,8 +1201,19 @@
 	struct bq24190_dev_info *bdi =
 		container_of(work, struct bq24190_dev_info,
 			     input_current_limit_work.work);
+	union power_supply_propval val;
+	int ret;
 
-	power_supply_set_input_current_limit_from_supplier(bdi->charger);
+	ret = power_supply_get_property_from_supplier(bdi->charger,
+						      POWER_SUPPLY_PROP_CURRENT_MAX,
+						      &val);
+	if (ret)
+		return;
+
+	bq24190_charger_set_property(bdi->charger,
+				     POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+				     &val);
+	power_supply_changed(bdi->charger);
 }
 
 /* Sync the input-current-limit with our parent supply (if we have one) */
@@ -1413,11 +1419,9 @@
 	dev_warn(bdi->dev, "warning: /sys/class/power_supply/bq24190-battery is deprecated\n");
 	dev_dbg(bdi->dev, "prop: %d\n", psp);
 
-	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_STATUS:
@@ -1461,11 +1465,9 @@
 	dev_warn(bdi->dev, "warning: /sys/class/power_supply/bq24190-battery is deprecated\n");
 	dev_dbg(bdi->dev, "prop: %d\n", psp);
 
-	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(bdi->dev);
+	ret = pm_runtime_resume_and_get(bdi->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_ONLINE:
@@ -1619,10 +1621,9 @@
 	int error;
 
 	bdi->irq_event = true;
-	error = pm_runtime_get_sync(bdi->dev);
+	error = pm_runtime_resume_and_get(bdi->dev);
 	if (error < 0) {
 		dev_warn(bdi->dev, "pm_runtime_get failed: %i\n", error);
-		pm_runtime_put_noidle(bdi->dev);
 		return IRQ_NONE;
 	}
 	bq24190_check_status(bdi);
@@ -1726,7 +1727,7 @@
 
 	bdi->client = client;
 	bdi->dev = dev;
-	strncpy(bdi->model_name, id->name, I2C_NAME_SIZE);
+	strscpy(bdi->model_name, id->name, sizeof(bdi->model_name));
 	mutex_init(&bdi->f_reg_lock);
 	bdi->f_reg = 0;
 	bdi->ss_reg = BQ24190_REG_SS_VBUS_STAT_MASK; /* impossible state */
@@ -1842,11 +1843,10 @@
 	struct bq24190_dev_info *bdi = i2c_get_clientdata(client);
 	int error;
 
-	error = pm_runtime_get_sync(bdi->dev);
-	if (error < 0) {
+	cancel_delayed_work_sync(&bdi->input_current_limit_work);
+	error = pm_runtime_resume_and_get(bdi->dev);
+	if (error < 0)
 		dev_warn(bdi->dev, "pm_runtime_get failed: %i\n", error);
-		pm_runtime_put_noidle(bdi->dev);
-	}
 
 	bq24190_register_reset(bdi);
 	if (bdi->battery)
@@ -1895,11 +1895,9 @@
 	struct bq24190_dev_info *bdi = i2c_get_clientdata(client);
 	int error;
 
-	error = pm_runtime_get_sync(bdi->dev);
-	if (error < 0) {
+	error = pm_runtime_resume_and_get(bdi->dev);
+	if (error < 0)
 		dev_warn(bdi->dev, "pm_runtime_get failed: %i\n", error);
-		pm_runtime_put_noidle(bdi->dev);
-	}
 
 	bq24190_register_reset(bdi);
 
@@ -1920,11 +1918,9 @@
 	bdi->f_reg = 0;
 	bdi->ss_reg = BQ24190_REG_SS_VBUS_STAT_MASK; /* impossible state */
 
-	error = pm_runtime_get_sync(bdi->dev);
-	if (error < 0) {
+	error = pm_runtime_resume_and_get(bdi->dev);
+	if (error < 0)
 		dev_warn(bdi->dev, "pm_runtime_get failed: %i\n", error);
-		pm_runtime_put_noidle(bdi->dev);
-	}
 
 	bq24190_register_reset(bdi);
 	bq24190_set_config(bdi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/bq256xx_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/bq256xx_charger.c
@@ -1514,13 +1514,16 @@
 			wd_reg_val = i;
 			break;
 		}
-		if (bq->watchdog_timer > bq256xx_watchdog_time[i] &&
+		if (i + 1 < BQ256XX_NUM_WD_VAL &&
+		    bq->watchdog_timer > bq256xx_watchdog_time[i] &&
 		    bq->watchdog_timer < bq256xx_watchdog_time[i + 1])
 			wd_reg_val = i;
 	}
 	ret = regmap_update_bits(bq->regmap, BQ256XX_CHARGER_CONTROL_1,
 				 BQ256XX_WATCHDOG_MASK, wd_reg_val <<
 						BQ256XX_WDT_BIT_SHIFT);
+	if (ret)
+		return ret;
 
 	ret = power_supply_get_battery_info(bq->charger, &bat_info);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/bq25890_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/bq25890_charger.c
@@ -581,12 +581,12 @@
 
 	if (!new_state.online && bq->state.online) {	    /* power removed */
 		/* disable ADC */
-		ret = bq25890_field_write(bq, F_CONV_START, 0);
+		ret = bq25890_field_write(bq, F_CONV_RATE, 0);
 		if (ret < 0)
 			goto error;
 	} else if (new_state.online && !bq->state.online) { /* power inserted */
 		/* enable ADC, to have control of charge current/voltage */
-		ret = bq25890_field_write(bq, F_CONV_START, 1);
+		ret = bq25890_field_write(bq, F_CONV_RATE, 1);
 		if (ret < 0)
 			goto error;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/bq27xxx_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/bq27xxx_battery.c
@@ -449,9 +449,29 @@
 		[BQ27XXX_REG_AP] = 0x18,
 		BQ27XXX_DM_REG_ROWS,
 	},
+	bq27426_regs[BQ27XXX_REG_MAX] = {
+		[BQ27XXX_REG_CTRL] = 0x00,
+		[BQ27XXX_REG_TEMP] = 0x02,
+		[BQ27XXX_REG_INT_TEMP] = 0x1e,
+		[BQ27XXX_REG_VOLT] = 0x04,
+		[BQ27XXX_REG_AI] = 0x10,
+		[BQ27XXX_REG_FLAGS] = 0x06,
+		[BQ27XXX_REG_TTE] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTF] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTES] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTECP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_NAC] = 0x08,
+		[BQ27XXX_REG_RC] = 0x0c,
+		[BQ27XXX_REG_FCC] = 0x0e,
+		[BQ27XXX_REG_CYCT] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_AE] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_SOC] = 0x1c,
+		[BQ27XXX_REG_DCAP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_AP] = 0x18,
+		BQ27XXX_DM_REG_ROWS,
+	},
 #define bq27411_regs bq27421_regs
 #define bq27425_regs bq27421_regs
-#define bq27426_regs bq27421_regs
 #define bq27441_regs bq27421_regs
 #define bq27621_regs bq27421_regs
 	bq27z561_regs[BQ27XXX_REG_MAX] = {
@@ -769,10 +789,23 @@
 };
 #define bq27411_props bq27421_props
 #define bq27425_props bq27421_props
-#define bq27426_props bq27421_props
 #define bq27441_props bq27421_props
 #define bq27621_props bq27421_props
 
+static enum power_supply_property bq27426_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
 static enum power_supply_property bq27z561_props[] = {
 	POWER_SUPPLY_PROP_STATUS,
 	POWER_SUPPLY_PROP_PRESENT,
@@ -1083,10 +1116,8 @@
 		return ret;
 
 	mutex_lock(&bq27xxx_list_lock);
-	list_for_each_entry(di, &bq27xxx_battery_devices, list) {
-		cancel_delayed_work_sync(&di->work);
-		schedule_delayed_work(&di->work, 0);
-	}
+	list_for_each_entry(di, &bq27xxx_battery_devices, list)
+		mod_delayed_work(system_wq, &di->work, 0);
 	mutex_unlock(&bq27xxx_list_lock);
 
 	return ret;
@@ -1572,14 +1603,6 @@
  */
 static inline int bq27xxx_battery_read_nac(struct bq27xxx_device_info *di)
 {
-	int flags;
-
-	if (di->opts & BQ27XXX_O_ZERO) {
-		flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, true);
-		if (flags >= 0 && (flags & BQ27000_FLAG_CI))
-			return -ENODATA;
-	}
-
 	return bq27xxx_battery_read_charge(di, BQ27XXX_REG_NAC);
 }
 
@@ -1742,6 +1765,18 @@
 		return flags & (BQ27XXX_FLAG_SOC1 | BQ27XXX_FLAG_SOCF);
 }
 
+/*
+ * Returns true if reported battery capacity is inaccurate
+ */
+static bool bq27xxx_battery_capacity_inaccurate(struct bq27xxx_device_info *di,
+						 u16 flags)
+{
+	if (di->opts & BQ27XXX_O_HAS_CI)
+		return (flags & BQ27000_FLAG_CI);
+	else
+		return false;
+}
+
 static int bq27xxx_battery_read_health(struct bq27xxx_device_info *di)
 {
 	/* Unlikely but important to return first */
@@ -1751,76 +1786,12 @@
 		return POWER_SUPPLY_HEALTH_COLD;
 	if (unlikely(bq27xxx_battery_dead(di, di->cache.flags)))
 		return POWER_SUPPLY_HEALTH_DEAD;
+	if (unlikely(bq27xxx_battery_capacity_inaccurate(di, di->cache.flags)))
+		return POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED;
 
 	return POWER_SUPPLY_HEALTH_GOOD;
 }
 
-void bq27xxx_battery_update(struct bq27xxx_device_info *di)
-{
-	struct bq27xxx_reg_cache cache = {0, };
-	bool has_ci_flag = di->opts & BQ27XXX_O_HAS_CI;
-	bool has_singe_flag = di->opts & BQ27XXX_O_ZERO;
-
-	cache.flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, has_singe_flag);
-	if ((cache.flags & 0xff) == 0xff)
-		cache.flags = -1; /* read error */
-	if (cache.flags >= 0) {
-		cache.temperature = bq27xxx_battery_read_temperature(di);
-		if (has_ci_flag && (cache.flags & BQ27000_FLAG_CI)) {
-			dev_info_once(di->dev, "battery is not calibrated! ignoring capacity values\n");
-			cache.capacity = -ENODATA;
-			cache.energy = -ENODATA;
-			cache.time_to_empty = -ENODATA;
-			cache.time_to_empty_avg = -ENODATA;
-			cache.time_to_full = -ENODATA;
-			cache.charge_full = -ENODATA;
-			cache.health = -ENODATA;
-		} else {
-			if (di->regs[BQ27XXX_REG_TTE] != INVALID_REG_ADDR)
-				cache.time_to_empty = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTE);
-			if (di->regs[BQ27XXX_REG_TTECP] != INVALID_REG_ADDR)
-				cache.time_to_empty_avg = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTECP);
-			if (di->regs[BQ27XXX_REG_TTF] != INVALID_REG_ADDR)
-				cache.time_to_full = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTF);
-
-			cache.charge_full = bq27xxx_battery_read_fcc(di);
-			cache.capacity = bq27xxx_battery_read_soc(di);
-			if (di->regs[BQ27XXX_REG_AE] != INVALID_REG_ADDR)
-				cache.energy = bq27xxx_battery_read_energy(di);
-			di->cache.flags = cache.flags;
-			cache.health = bq27xxx_battery_read_health(di);
-		}
-		if (di->regs[BQ27XXX_REG_CYCT] != INVALID_REG_ADDR)
-			cache.cycle_count = bq27xxx_battery_read_cyct(di);
-
-		/* We only have to read charge design full once */
-		if (di->charge_design_full <= 0)
-			di->charge_design_full = bq27xxx_battery_read_dcap(di);
-	}
-
-	if ((di->cache.capacity != cache.capacity) ||
-	    (di->cache.flags != cache.flags))
-		power_supply_changed(di->bat);
-
-	if (memcmp(&di->cache, &cache, sizeof(cache)) != 0)
-		di->cache = cache;
-
-	di->last_update = jiffies;
-}
-EXPORT_SYMBOL_GPL(bq27xxx_battery_update);
-
-static void bq27xxx_battery_poll(struct work_struct *work)
-{
-	struct bq27xxx_device_info *di =
-			container_of(work, struct bq27xxx_device_info,
-				     work.work);
-
-	bq27xxx_battery_update(di);
-
-	if (poll_interval > 0)
-		schedule_delayed_work(&di->work, poll_interval * HZ);
-}
-
 static bool bq27xxx_battery_is_full(struct bq27xxx_device_info *di, int flags)
 {
 	if (di->opts & BQ27XXX_O_ZERO)
@@ -1839,7 +1810,8 @@
 static int bq27xxx_battery_current_and_status(
 	struct bq27xxx_device_info *di,
 	union power_supply_propval *val_curr,
-	union power_supply_propval *val_status)
+	union power_supply_propval *val_status,
+	struct bq27xxx_reg_cache *cache)
 {
 	bool single_flags = (di->opts & BQ27XXX_O_ZERO);
 	int curr;
@@ -1851,10 +1823,14 @@
 		return curr;
 	}
 
-	flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, single_flags);
-	if (flags < 0) {
-		dev_err(di->dev, "error reading flags\n");
-		return flags;
+	if (cache) {
+		flags = cache->flags;
+	} else {
+		flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, single_flags);
+		if (flags < 0) {
+			dev_err(di->dev, "error reading flags\n");
+			return flags;
+		}
 	}
 
 	if (di->opts & BQ27XXX_O_ZERO) {
@@ -1889,6 +1865,78 @@
 	return 0;
 }
 
+static void bq27xxx_battery_update_unlocked(struct bq27xxx_device_info *di)
+{
+	union power_supply_propval status = di->last_status;
+	struct bq27xxx_reg_cache cache = {0, };
+	bool has_singe_flag = di->opts & BQ27XXX_O_ZERO;
+
+	cache.flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, has_singe_flag);
+	if ((cache.flags & 0xff) == 0xff)
+		cache.flags = -1; /* read error */
+	if (cache.flags >= 0) {
+		cache.temperature = bq27xxx_battery_read_temperature(di);
+		if (di->regs[BQ27XXX_REG_TTE] != INVALID_REG_ADDR)
+			cache.time_to_empty = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTE);
+		if (di->regs[BQ27XXX_REG_TTECP] != INVALID_REG_ADDR)
+			cache.time_to_empty_avg = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTECP);
+		if (di->regs[BQ27XXX_REG_TTF] != INVALID_REG_ADDR)
+			cache.time_to_full = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTF);
+
+		cache.charge_full = bq27xxx_battery_read_fcc(di);
+		cache.capacity = bq27xxx_battery_read_soc(di);
+		if (di->regs[BQ27XXX_REG_AE] != INVALID_REG_ADDR)
+			cache.energy = bq27xxx_battery_read_energy(di);
+		di->cache.flags = cache.flags;
+		cache.health = bq27xxx_battery_read_health(di);
+		if (di->regs[BQ27XXX_REG_CYCT] != INVALID_REG_ADDR)
+			cache.cycle_count = bq27xxx_battery_read_cyct(di);
+
+		/*
+		 * On gauges with signed current reporting the current must be
+		 * checked to detect charging <-> discharging status changes.
+		 */
+		if (!(di->opts & BQ27XXX_O_ZERO))
+			bq27xxx_battery_current_and_status(di, NULL, &status, &cache);
+
+		/* We only have to read charge design full once */
+		if (di->charge_design_full <= 0)
+			di->charge_design_full = bq27xxx_battery_read_dcap(di);
+	}
+
+	if ((di->cache.capacity != cache.capacity) ||
+	    (di->cache.flags != cache.flags) ||
+	    (di->last_status.intval != status.intval)) {
+		di->last_status.intval = status.intval;
+		power_supply_changed(di->bat);
+	}
+
+	if (memcmp(&di->cache, &cache, sizeof(cache)) != 0)
+		di->cache = cache;
+
+	di->last_update = jiffies;
+
+	if (!di->removed && poll_interval > 0)
+		mod_delayed_work(system_wq, &di->work, poll_interval * HZ);
+}
+
+void bq27xxx_battery_update(struct bq27xxx_device_info *di)
+{
+	mutex_lock(&di->lock);
+	bq27xxx_battery_update_unlocked(di);
+	mutex_unlock(&di->lock);
+}
+EXPORT_SYMBOL_GPL(bq27xxx_battery_update);
+
+static void bq27xxx_battery_poll(struct work_struct *work)
+{
+	struct bq27xxx_device_info *di =
+			container_of(work, struct bq27xxx_device_info,
+				     work.work);
+
+	bq27xxx_battery_update(di);
+}
+
 /*
  * Get the average power in µW
  * Return < 0 if something fails.
@@ -1991,10 +2039,8 @@
 	struct bq27xxx_device_info *di = power_supply_get_drvdata(psy);
 
 	mutex_lock(&di->lock);
-	if (time_is_before_jiffies(di->last_update + 5 * HZ)) {
-		cancel_delayed_work_sync(&di->work);
-		bq27xxx_battery_poll(&di->work.work);
-	}
+	if (time_is_before_jiffies(di->last_update + 5 * HZ))
+		bq27xxx_battery_update_unlocked(di);
 	mutex_unlock(&di->lock);
 
 	if (psp != POWER_SUPPLY_PROP_PRESENT && di->cache.flags < 0)
@@ -2002,7 +2048,7 @@
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_STATUS:
-		ret = bq27xxx_battery_current_and_status(di, NULL, val);
+		ret = bq27xxx_battery_current_and_status(di, NULL, val, NULL);
 		break;
 	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
 		ret = bq27xxx_battery_voltage(di, val);
@@ -2011,7 +2057,7 @@
 		val->intval = di->cache.flags < 0 ? 0 : 1;
 		break;
 	case POWER_SUPPLY_PROP_CURRENT_NOW:
-		ret = bq27xxx_battery_current_and_status(di, val, NULL);
+		ret = bq27xxx_battery_current_and_status(di, val, NULL, NULL);
 		break;
 	case POWER_SUPPLY_PROP_CAPACITY:
 		ret = bq27xxx_simple_value(di->cache.capacity, val);
@@ -2084,8 +2130,8 @@
 {
 	struct bq27xxx_device_info *di = power_supply_get_drvdata(psy);
 
-	cancel_delayed_work_sync(&di->work);
-	schedule_delayed_work(&di->work, 0);
+	/* After charger plug in/out wait 0.5s for things to stabilize */
+	mod_delayed_work(system_wq, &di->work, HZ / 2);
 }
 
 int bq27xxx_battery_setup(struct bq27xxx_device_info *di)
@@ -2133,22 +2179,18 @@
 
 void bq27xxx_battery_teardown(struct bq27xxx_device_info *di)
 {
-	/*
-	 * power_supply_unregister call bq27xxx_battery_get_property which
-	 * call bq27xxx_battery_poll.
-	 * Make sure that bq27xxx_battery_poll will not call
-	 * schedule_delayed_work again after unregister (which cause OOPS).
-	 */
-	poll_interval = 0;
-
-	cancel_delayed_work_sync(&di->work);
-
-	power_supply_unregister(di->bat);
-
 	mutex_lock(&bq27xxx_list_lock);
 	list_del(&di->list);
 	mutex_unlock(&bq27xxx_list_lock);
 
+	/* Set removed to avoid bq27xxx_battery_update() re-queuing the work */
+	mutex_lock(&di->lock);
+	di->removed = true;
+	mutex_unlock(&di->lock);
+
+	cancel_delayed_work_sync(&di->work);
+
+	power_supply_unregister(di->bat);
 	mutex_destroy(&di->lock);
 }
 EXPORT_SYMBOL_GPL(bq27xxx_battery_teardown);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/bq27xxx_battery_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/bq27xxx_battery_i2c.c
@@ -179,7 +179,7 @@
 	i2c_set_clientdata(client, di);
 
 	if (client->irq) {
-		ret = devm_request_threaded_irq(&client->dev, client->irq,
+		ret = request_threaded_irq(client->irq,
 				NULL, bq27xxx_battery_irq_handler_thread,
 				IRQF_ONESHOT,
 				di->name, di);
@@ -187,7 +187,8 @@
 			dev_err(&client->dev,
 				"Unable to register IRQ %d error %d\n",
 				client->irq, ret);
-			return ret;
+			bq27xxx_battery_teardown(di);
+			goto err_failed;
 		}
 	}
 
@@ -208,6 +209,9 @@
 {
 	struct bq27xxx_device_info *di = i2c_get_clientdata(client);
 
+	if (client->irq)
+		free_irq(client->irq, di);
+
 	bq27xxx_battery_teardown(di);
 
 	mutex_lock(&battery_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/charger-manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/charger-manager.c
@@ -985,13 +985,10 @@
 	cable->nb.notifier_call = charger_extcon_notifier;
 
 	cable->extcon_dev = extcon_get_extcon_dev(cable->extcon_name);
-	if (IS_ERR_OR_NULL(cable->extcon_dev)) {
+	if (IS_ERR(cable->extcon_dev)) {
 		pr_err("Cannot find extcon_dev for %s (cable: %s)\n",
 			cable->extcon_name, cable->name);
-		if (cable->extcon_dev == NULL)
-			return -EPROBE_DEFER;
-		else
-			return PTR_ERR(cable->extcon_dev);
+		return PTR_ERR(cable->extcon_dev);
 	}
 
 	for (i = 0; i < ARRAY_SIZE(extcon_mapping); i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/cros_usbpd-charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/cros_usbpd-charger.c
@@ -5,6 +5,7 @@
  * Copyright (c) 2014 - 2018 Google, Inc
  */
 
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/platform_data/cros_ec_commands.h>
 #include <linux/platform_data/cros_ec_proto.h>
@@ -276,7 +277,7 @@
 		port->psy_current_max = 0;
 		break;
 	default:
-		dev_err(dev, "Port %d: default case!\n", port->port_number);
+		dev_dbg(dev, "Port %d: default case!\n", port->port_number);
 		port->psy_usb_type = POWER_SUPPLY_USB_TYPE_SDP;
 	}
 
@@ -711,16 +712,22 @@
 static SIMPLE_DEV_PM_OPS(cros_usbpd_charger_pm_ops, NULL,
 			 cros_usbpd_charger_resume);
 
+static const struct platform_device_id cros_usbpd_charger_id[] = {
+	{ DRV_NAME, 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, cros_usbpd_charger_id);
+
 static struct platform_driver cros_usbpd_charger_driver = {
 	.driver = {
 		.name = DRV_NAME,
 		.pm = &cros_usbpd_charger_pm_ops,
 	},
-	.probe = cros_usbpd_charger_probe
+	.probe = cros_usbpd_charger_probe,
+	.id_table = cros_usbpd_charger_id,
 };
 
 module_platform_driver(cros_usbpd_charger_driver);
 
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("ChromeOS EC USBPD charger");
-MODULE_ALIAS("platform:" DRV_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/cw2015_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/cw2015_battery.c
@@ -490,7 +490,7 @@
 
 	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW:
 		if (cw_battery_valid_time_to_empty(cw_bat))
-			val->intval = cw_bat->time_to_empty;
+			val->intval = cw_bat->time_to_empty * 60;
 		else
 			val->intval = 0;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/da9150-charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/da9150-charger.c
@@ -662,6 +662,7 @@
 
 	if (!IS_ERR_OR_NULL(charger->usb_phy))
 		usb_unregister_notifier(charger->usb_phy, &charger->otg_nb);
+	cancel_work_sync(&charger->otg_work);
 
 	power_supply_unregister(charger->battery);
 	power_supply_unregister(charger->usb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/da9150-fg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/da9150-fg.c
@@ -247,9 +247,9 @@
 				      DA9150_QIF_SD_GAIN_SIZE);
 	da9150_fg_read_sync_end(fg);
 
-	div = (u64) (sd_gain * shunt_val * 65536ULL);
+	div = 65536ULL * sd_gain * shunt_val;
 	do_div(div, 1000000);
-	res = (u64) (iavg * 1000000ULL);
+	res = 1000000ULL * iavg;
 	do_div(res, div);
 
 	val->intval = (int) res;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/generic-adc-battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/generic-adc-battery.c
@@ -135,6 +135,9 @@
 			result);
 	if (ret < 0)
 		pr_err("read channel error\n");
+	else
+		*result *= 1000;
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/gpio-charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/gpio-charger.c
@@ -67,6 +67,14 @@
 		if (gpio_charger->current_limit_map[i].limit_ua <= val)
 			break;
 	}
+
+	/*
+	 * If a valid charge current limit isn't found, default to smallest
+	 * current limitation for safety reasons.
+	 */
+	if (i >= gpio_charger->current_limit_map_size)
+		i = gpio_charger->current_limit_map_size - 1;
+
 	mapping = gpio_charger->current_limit_map[i];
 
 	for (i = 0; i < ndescs; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/max17040_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/max17040_battery.c
@@ -449,6 +449,8 @@
 
 	chip->client = client;
 	chip->regmap = devm_regmap_init_i2c(client, &max17040_regmap);
+	if (IS_ERR(chip->regmap))
+		return PTR_ERR(chip->regmap);
 	chip_id = (enum chip_id) id->driver_data;
 	if (client->dev.of_node) {
 		ret = max17040_get_of_data(chip);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/max17042_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/max17042_battery.c
@@ -313,7 +313,10 @@
 		val->intval = data * 625 / 8;
 		break;
 	case POWER_SUPPLY_PROP_CAPACITY:
-		ret = regmap_read(map, MAX17042_RepSOC, &data);
+		if (chip->pdata->enable_current_sense)
+			ret = regmap_read(map, MAX17042_RepSOC, &data);
+		else
+			ret = regmap_read(map, MAX17042_VFSOC, &data);
 		if (ret < 0)
 			return ret;
 
@@ -854,10 +857,14 @@
 	/* program interrupt thresholds such that we should
 	 * get interrupt for every 'off' perc change in the soc
 	 */
-	regmap_read(map, MAX17042_RepSOC, &soc);
+	if (chip->pdata->enable_current_sense)
+		regmap_read(map, MAX17042_RepSOC, &soc);
+	else
+		regmap_read(map, MAX17042_VFSOC, &soc);
 	soc >>= 8;
 	soc_tr = (soc + off) << 8;
-	soc_tr |= (soc - off);
+	if (off < soc)
+		soc_tr |= soc - off;
 	regmap_write(map, MAX17042_SALRT_Th, soc_tr);
 }
 
@@ -876,6 +883,10 @@
 		max17042_set_soc_threshold(chip, 1);
 	}
 
+	/* we implicitly handle all alerts via power_supply_changed */
+	regmap_clear_bits(chip->regmap, MAX17042_STATUS,
+			  0xFFFF & ~(STATUS_POR_BIT | STATUS_BST_BIT));
+
 	power_supply_changed(chip->battery);
 	return IRQ_HANDLED;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/max77693_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/max77693_charger.c
@@ -556,7 +556,7 @@
 	case 4700000:
 	case 4800000:
 	case 4900000:
-		data = (uvolt - 4700000) / 100000;
+		data = ((uvolt - 4700000) / 100000) + 1;
 		break;
 	default:
 		dev_err(chg->dev, "Wrong value for charge input voltage regulation threshold\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/max8997_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/max8997_charger.c
@@ -248,10 +248,10 @@
 		dev_info(&pdev->dev, "couldn't get charger regulator\n");
 	}
 	charger->edev = extcon_get_extcon_dev("max8997-muic");
-	if (IS_ERR_OR_NULL(charger->edev)) {
-		if (!charger->edev)
-			return -EPROBE_DEFER;
-		dev_info(charger->dev, "couldn't get extcon device\n");
+	if (IS_ERR(charger->edev)) {
+		dev_err_probe(charger->dev, PTR_ERR(charger->edev),
+			      "couldn't get extcon device: max8997-muic\n");
+		return PTR_ERR(charger->edev);
 	}
 
 	if (!IS_ERR(charger->reg) && !IS_ERR_OR_NULL(charger->edev)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/mt6360_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/mt6360_charger.c
@@ -591,7 +591,7 @@
 };
 
 static const struct regulator_desc mt6360_otg_rdesc = {
-	.of_match = "usb-otg-vbus",
+	.of_match = "usb-otg-vbus-regulator",
 	.name = "usb-otg-vbus",
 	.ops = &mt6360_chg_otg_ops,
 	.owner = THIS_MODULE,
@@ -799,7 +799,9 @@
 	mci->vinovp = 6500000;
 	mutex_init(&mci->chgdet_lock);
 	platform_set_drvdata(pdev, mci);
-	devm_work_autocancel(&pdev->dev, &mci->chrdet_work, mt6360_chrdet_work);
+	ret = devm_work_autocancel(&pdev->dev, &mci->chrdet_work, mt6360_chrdet_work);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret, "Failed to set delayed work\n");
 
 	ret = device_property_read_u32(&pdev->dev, "richtek,vinovp-microvolt", &mci->vinovp);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/power_supply_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/power_supply_core.c
@@ -347,6 +347,10 @@
 	struct power_supply *psy = dev_get_drvdata(dev);
 	unsigned int *count = data;
 
+	if (!psy->desc->get_property(psy, POWER_SUPPLY_PROP_SCOPE, &ret))
+		if (ret.intval == POWER_SUPPLY_SCOPE_DEVICE)
+			return 0;
+
 	(*count)++;
 	if (psy->desc->type != POWER_SUPPLY_TYPE_BATTERY)
 		if (!psy->desc->get_property(psy, POWER_SUPPLY_PROP_ONLINE,
@@ -365,8 +369,8 @@
 				      __power_supply_is_system_supplied);
 
 	/*
-	 * If no power class device was found at all, most probably we are
-	 * running on a desktop system, so assume we are on mains power.
+	 * If no system scope power class device was found at all, most probably we
+	 * are running on a desktop system, so assume we are on mains power.
 	 */
 	if (count == 0)
 		return 1;
@@ -375,46 +379,49 @@
 }
 EXPORT_SYMBOL_GPL(power_supply_is_system_supplied);
 
-static int __power_supply_get_supplier_max_current(struct device *dev,
-						   void *data)
+struct psy_get_supplier_prop_data {
+	struct power_supply *psy;
+	enum power_supply_property psp;
+	union power_supply_propval *val;
+};
+
+static int __power_supply_get_supplier_property(struct device *dev, void *_data)
 {
-	union power_supply_propval ret = {0,};
 	struct power_supply *epsy = dev_get_drvdata(dev);
-	struct power_supply *psy = data;
+	struct psy_get_supplier_prop_data *data = _data;
 
-	if (__power_supply_is_supplied_by(epsy, psy))
-		if (!epsy->desc->get_property(epsy,
-					      POWER_SUPPLY_PROP_CURRENT_MAX,
-					      &ret))
-			return ret.intval;
+	if (__power_supply_is_supplied_by(epsy, data->psy))
+		if (!epsy->desc->get_property(epsy, data->psp, data->val))
+			return 1; /* Success */
 
-	return 0;
+	return 0; /* Continue iterating */
 }
 
-int power_supply_set_input_current_limit_from_supplier(struct power_supply *psy)
+int power_supply_get_property_from_supplier(struct power_supply *psy,
+					    enum power_supply_property psp,
+					    union power_supply_propval *val)
 {
-	union power_supply_propval val = {0,};
-	int curr;
-
-	if (!psy->desc->set_property)
-		return -EINVAL;
+	struct psy_get_supplier_prop_data data = {
+		.psy = psy,
+		.psp = psp,
+		.val = val,
+	};
+	int ret;
 
 	/*
 	 * This function is not intended for use with a supply with multiple
-	 * suppliers, we simply pick the first supply to report a non 0
-	 * max-current.
+	 * suppliers, we simply pick the first supply to report the psp.
 	 */
-	curr = class_for_each_device(power_supply_class, NULL, psy,
-				      __power_supply_get_supplier_max_current);
-	if (curr <= 0)
-		return (curr == 0) ? -ENODEV : curr;
-
-	val.intval = curr;
+	ret = class_for_each_device(power_supply_class, NULL, &data,
+				    __power_supply_get_supplier_property);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		return -ENODEV;
 
-	return psy->desc->set_property(psy,
-				POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT, &val);
+	return 0;
 }
-EXPORT_SYMBOL_GPL(power_supply_set_input_current_limit_from_supplier);
+EXPORT_SYMBOL_GPL(power_supply_get_property_from_supplier);
 
 int power_supply_set_battery_charged(struct power_supply *psy)
 {
@@ -472,8 +479,6 @@
  */
 void power_supply_put(struct power_supply *psy)
 {
-	might_sleep();
-
 	atomic_dec(&psy->use_cnt);
 	put_device(&psy->dev);
 }
@@ -696,6 +701,11 @@
 		int i, tab_len, size;
 
 		propname = kasprintf(GFP_KERNEL, "ocv-capacity-table-%d", index);
+		if (!propname) {
+			power_supply_put_battery_info(psy, info);
+			err = -ENOMEM;
+			goto out_put_node;
+		}
 		list = of_get_property(battery_np, propname, &size);
 		if (!list || !size) {
 			dev_err(&psy->dev, "failed to get %s\n", propname);
@@ -853,6 +863,10 @@
 		return NULL;
 
 	for (i = 0; i < POWER_SUPPLY_OCV_TEMP_MAX; i++) {
+		/* Out of capacity tables */
+		if (!info->ocv_table[i])
+			break;
+
 		temp_diff = abs(info->ocv_temp[i] - temp);
 
 		if (temp_diff < best_temp_diff) {
@@ -1005,87 +1019,6 @@
 	thermal_zone_device_unregister(psy->tzd);
 }
 
-/* thermal cooling device callbacks */
-static int ps_get_max_charge_cntl_limit(struct thermal_cooling_device *tcd,
-					unsigned long *state)
-{
-	struct power_supply *psy;
-	union power_supply_propval val;
-	int ret;
-
-	psy = tcd->devdata;
-	ret = power_supply_get_property(psy,
-			POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX, &val);
-	if (ret)
-		return ret;
-
-	*state = val.intval;
-
-	return ret;
-}
-
-static int ps_get_cur_charge_cntl_limit(struct thermal_cooling_device *tcd,
-					unsigned long *state)
-{
-	struct power_supply *psy;
-	union power_supply_propval val;
-	int ret;
-
-	psy = tcd->devdata;
-	ret = power_supply_get_property(psy,
-			POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT, &val);
-	if (ret)
-		return ret;
-
-	*state = val.intval;
-
-	return ret;
-}
-
-static int ps_set_cur_charge_cntl_limit(struct thermal_cooling_device *tcd,
-					unsigned long state)
-{
-	struct power_supply *psy;
-	union power_supply_propval val;
-	int ret;
-
-	psy = tcd->devdata;
-	val.intval = state;
-	ret = psy->desc->set_property(psy,
-		POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT, &val);
-
-	return ret;
-}
-
-static const struct thermal_cooling_device_ops psy_tcd_ops = {
-	.get_max_state = ps_get_max_charge_cntl_limit,
-	.get_cur_state = ps_get_cur_charge_cntl_limit,
-	.set_cur_state = ps_set_cur_charge_cntl_limit,
-};
-
-static int psy_register_cooler(struct power_supply *psy)
-{
-	int i;
-
-	/* Register for cooling device if psy can control charging */
-	for (i = 0; i < psy->desc->num_properties; i++) {
-		if (psy->desc->properties[i] ==
-				POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT) {
-			psy->tcd = thermal_cooling_device_register(
-							(char *)psy->desc->name,
-							psy, &psy_tcd_ops);
-			return PTR_ERR_OR_ZERO(psy->tcd);
-		}
-	}
-	return 0;
-}
-
-static void psy_unregister_cooler(struct power_supply *psy)
-{
-	if (IS_ERR_OR_NULL(psy->tcd))
-		return;
-	thermal_cooling_device_unregister(psy->tcd);
-}
 #else
 static int psy_register_thermal(struct power_supply *psy)
 {
@@ -1095,15 +1028,6 @@
 static void psy_unregister_thermal(struct power_supply *psy)
 {
 }
-
-static int psy_register_cooler(struct power_supply *psy)
-{
-	return 0;
-}
-
-static void psy_unregister_cooler(struct power_supply *psy)
-{
-}
 #endif
 
 static struct power_supply *__must_check
@@ -1179,10 +1103,6 @@
 	if (rc)
 		goto register_thermal_failed;
 
-	rc = psy_register_cooler(psy);
-	if (rc)
-		goto register_cooler_failed;
-
 	rc = power_supply_create_triggers(psy);
 	if (rc)
 		goto create_triggers_failed;
@@ -1212,12 +1132,10 @@
 add_hwmon_sysfs_failed:
 	power_supply_remove_triggers(psy);
 create_triggers_failed:
-	psy_unregister_cooler(psy);
-register_cooler_failed:
 	psy_unregister_thermal(psy);
 register_thermal_failed:
-	device_del(dev);
 wakeup_init_failed:
+	device_del(dev);
 device_add_failed:
 check_supplies_failed:
 dev_set_name_failed:
@@ -1365,7 +1283,6 @@
 	sysfs_remove_link(&psy->dev.kobj, "powers");
 	power_supply_remove_hwmon_sysfs(psy);
 	power_supply_remove_triggers(psy);
-	psy_unregister_cooler(psy);
 	psy_unregister_thermal(psy);
 	device_init_wakeup(&psy->dev, false);
 	device_unregister(&psy->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/power_supply_hwmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/power_supply_hwmon.c
@@ -299,7 +299,8 @@
 			   HWMON_T_INPUT     |
 			   HWMON_T_MAX       |
 			   HWMON_T_MIN       |
-			   HWMON_T_MIN_ALARM,
+			   HWMON_T_MIN_ALARM |
+			   HWMON_T_MAX_ALARM,
 
 			   HWMON_T_LABEL     |
 			   HWMON_T_INPUT     |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/power_supply_leds.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/power_supply_leds.c
@@ -34,8 +34,9 @@
 		led_trigger_event(psy->charging_full_trig, LED_FULL);
 		led_trigger_event(psy->charging_trig, LED_OFF);
 		led_trigger_event(psy->full_trig, LED_FULL);
-		led_trigger_event(psy->charging_blink_full_solid_trig,
-			LED_FULL);
+		/* Going from blink to LED on requires a LED_OFF event to stop blink */
+		led_trigger_event(psy->charging_blink_full_solid_trig, LED_OFF);
+		led_trigger_event(psy->charging_blink_full_solid_trig, LED_FULL);
 		break;
 	case POWER_SUPPLY_STATUS_CHARGING:
 		led_trigger_event(psy->charging_full_trig, LED_FULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/power_supply_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/power_supply_sysfs.c
@@ -276,7 +276,8 @@
 
 		if (ret < 0) {
 			if (ret == -ENODATA)
-				dev_dbg(dev, "driver has no data for `%s' property\n",
+				dev_dbg_ratelimited(dev,
+					"driver has no data for `%s' property\n",
 					attr->attr.name);
 			else if (ret != -ENODEV && ret != -EAGAIN)
 				dev_err_ratelimited(dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/rt5033_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/rt5033_battery.c
@@ -60,7 +60,7 @@
 	regmap_read(battery->regmap, regh, &msb);
 	regmap_read(battery->regmap, regl, &lsb);
 
-	ret = ((msb << 4) + (lsb >> 4)) * 1250 / 1000;
+	ret = ((msb << 4) + (lsb >> 4)) * 1250;
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/rt9455_charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/rt9455_charger.c
@@ -193,6 +193,7 @@
 	4450000, 4450000, 4450000, 4450000, 4450000, 4450000, 4450000, 4450000
 };
 
+#if IS_ENABLED(CONFIG_USB_PHY)
 /*
  * When the charger is in boost mode, REG02[7:2] represent boost output
  * voltage.
@@ -208,6 +209,7 @@
 	5600000, 5600000, 5600000, 5600000, 5600000, 5600000, 5600000, 5600000,
 	5600000, 5600000, 5600000, 5600000, 5600000, 5600000, 5600000, 5600000,
 };
+#endif
 
 /* REG07[3:0] (VMREG) in uV */
 static const int rt9455_vmreg_values[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/sbs-charger.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/sbs-charger.c
@@ -18,12 +18,13 @@
 #include <linux/interrupt.h>
 #include <linux/regmap.h>
 #include <linux/bitops.h>
+#include <linux/devm-helpers.h>
 
 #define SBS_CHARGER_REG_SPEC_INFO		0x11
 #define SBS_CHARGER_REG_STATUS			0x13
 #define SBS_CHARGER_REG_ALARM_WARNING		0x16
 
-#define SBS_CHARGER_STATUS_CHARGE_INHIBITED	BIT(1)
+#define SBS_CHARGER_STATUS_CHARGE_INHIBITED	BIT(0)
 #define SBS_CHARGER_STATUS_RES_COLD		BIT(9)
 #define SBS_CHARGER_STATUS_RES_HOT		BIT(10)
 #define SBS_CHARGER_STATUS_BATTERY_PRESENT	BIT(14)
@@ -209,7 +210,12 @@
 		if (ret)
 			return dev_err_probe(&client->dev, ret, "Failed to request irq\n");
 	} else {
-		INIT_DELAYED_WORK(&chip->work, sbs_delayed_work);
+		ret = devm_delayed_work_autocancel(&client->dev, &chip->work,
+						   sbs_delayed_work);
+		if (ret)
+			return dev_err_probe(&client->dev, ret,
+					     "Failed to init work for polling\n");
+
 		schedule_delayed_work(&chip->work,
 				      msecs_to_jiffies(SBS_CHARGER_POLL_TIME));
 	}
@@ -220,15 +226,6 @@
 	return 0;
 }
 
-static int sbs_remove(struct i2c_client *client)
-{
-	struct sbs_info *chip = i2c_get_clientdata(client);
-
-	cancel_delayed_work_sync(&chip->work);
-
-	return 0;
-}
-
 #ifdef CONFIG_OF
 static const struct of_device_id sbs_dt_ids[] = {
 	{ .compatible = "sbs,sbs-charger" },
@@ -245,7 +242,6 @@
 
 static struct i2c_driver sbs_driver = {
 	.probe		= sbs_probe,
-	.remove		= sbs_remove,
 	.id_table	= sbs_id,
 	.driver = {
 		.name	= "sbs-charger",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/sc27xx_fuel_gauge.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/sc27xx_fuel_gauge.c
@@ -733,13 +733,6 @@
 	return ret;
 }
 
-static void sc27xx_fgu_external_power_changed(struct power_supply *psy)
-{
-	struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy);
-
-	power_supply_changed(data->battery);
-}
-
 static int sc27xx_fgu_property_is_writeable(struct power_supply *psy,
 					    enum power_supply_property psp)
 {
@@ -774,7 +767,7 @@
 	.num_properties		= ARRAY_SIZE(sc27xx_fgu_props),
 	.get_property		= sc27xx_fgu_get_property,
 	.set_property		= sc27xx_fgu_set_property,
-	.external_power_changed	= sc27xx_fgu_external_power_changed,
+	.external_power_changed	= power_supply_changed,
 	.property_is_writeable	= sc27xx_fgu_property_is_writeable,
 	.no_thermal		= true,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/ucs1002_power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/ucs1002_power.c
@@ -384,7 +384,8 @@
 	case POWER_SUPPLY_PROP_USB_TYPE:
 		return ucs1002_get_usb_type(info, val);
 	case POWER_SUPPLY_PROP_HEALTH:
-		return val->intval = info->health;
+		val->intval = info->health;
+		return 0;
 	case POWER_SUPPLY_PROP_PRESENT:
 		val->intval = info->present;
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/wm8350_power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/wm8350_power.c
@@ -408,44 +408,112 @@
  *		Initialisation
  *********************************************************************/
 
-static void wm8350_init_charger(struct wm8350 *wm8350)
+static int wm8350_init_charger(struct wm8350 *wm8350)
 {
+	int ret;
+
 	/* register our interest in charger events */
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_BAT_HOT,
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_BAT_HOT,
 			    wm8350_charger_handler, 0, "Battery hot", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_BAT_COLD,
+	if (ret)
+		goto err;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_BAT_COLD,
 			    wm8350_charger_handler, 0, "Battery cold", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_BAT_FAIL,
+	if (ret)
+		goto free_chg_bat_hot;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_BAT_FAIL,
 			    wm8350_charger_handler, 0, "Battery fail", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_TO,
+	if (ret)
+		goto free_chg_bat_cold;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_TO,
 			    wm8350_charger_handler, 0,
 			    "Charger timeout", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_END,
+	if (ret)
+		goto free_chg_bat_fail;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_END,
 			    wm8350_charger_handler, 0,
 			    "Charge end", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_START,
+	if (ret)
+		goto free_chg_to;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_START,
 			    wm8350_charger_handler, 0,
 			    "Charge start", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_FAST_RDY,
+	if (ret)
+		goto free_chg_end;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_FAST_RDY,
 			    wm8350_charger_handler, 0,
 			    "Fast charge ready", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P9,
+	if (ret)
+		goto free_chg_start;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P9,
 			    wm8350_charger_handler, 0,
 			    "Battery <3.9V", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P1,
+	if (ret)
+		goto free_chg_fast_rdy;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P1,
 			    wm8350_charger_handler, 0,
 			    "Battery <3.1V", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_2P85,
+	if (ret)
+		goto free_chg_vbatt_lt_3p9;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_2P85,
 			    wm8350_charger_handler, 0,
 			    "Battery <2.85V", wm8350);
+	if (ret)
+		goto free_chg_vbatt_lt_3p1;
 
 	/* and supply change events */
-	wm8350_register_irq(wm8350, WM8350_IRQ_EXT_USB_FB,
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_EXT_USB_FB,
 			    wm8350_charger_handler, 0, "USB", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_EXT_WALL_FB,
+	if (ret)
+		goto free_chg_vbatt_lt_2p85;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_EXT_WALL_FB,
 			    wm8350_charger_handler, 0, "Wall", wm8350);
-	wm8350_register_irq(wm8350, WM8350_IRQ_EXT_BAT_FB,
+	if (ret)
+		goto free_ext_usb_fb;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_EXT_BAT_FB,
 			    wm8350_charger_handler, 0, "Battery", wm8350);
+	if (ret)
+		goto free_ext_wall_fb;
+
+	return 0;
+
+free_ext_wall_fb:
+	wm8350_free_irq(wm8350, WM8350_IRQ_EXT_WALL_FB, wm8350);
+free_ext_usb_fb:
+	wm8350_free_irq(wm8350, WM8350_IRQ_EXT_USB_FB, wm8350);
+free_chg_vbatt_lt_2p85:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_2P85, wm8350);
+free_chg_vbatt_lt_3p1:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P1, wm8350);
+free_chg_vbatt_lt_3p9:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P9, wm8350);
+free_chg_fast_rdy:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_FAST_RDY, wm8350);
+free_chg_start:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_START, wm8350);
+free_chg_end:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_END, wm8350);
+free_chg_to:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_TO, wm8350);
+free_chg_bat_fail:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_FAIL, wm8350);
+free_chg_bat_cold:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_COLD, wm8350);
+free_chg_bat_hot:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_HOT, wm8350);
+err:
+	return ret;
 }
 
 static void free_charger_irq(struct wm8350 *wm8350)
@@ -456,6 +524,7 @@
 	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_TO, wm8350);
 	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_END, wm8350);
 	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_START, wm8350);
+	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_FAST_RDY, wm8350);
 	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P9, wm8350);
 	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P1, wm8350);
 	wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_2P85, wm8350);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/power/supply/z2_battery.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/power/supply/z2_battery.c
@@ -206,10 +206,12 @@
 
 	charger->charge_gpiod = devm_gpiod_get_optional(&client->dev,
 							NULL, GPIOD_IN);
-	if (IS_ERR(charger->charge_gpiod))
-		return dev_err_probe(&client->dev,
+	if (IS_ERR(charger->charge_gpiod)) {
+		ret = dev_err_probe(&client->dev,
 				     PTR_ERR(charger->charge_gpiod),
 				     "failed to get charge GPIO\n");
+		goto err;
+	}
 
 	if (charger->charge_gpiod) {
 		gpiod_set_consumer_name(charger->charge_gpiod, "BATT CHRG");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/powercap/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/powercap/Kconfig
@@ -18,10 +18,12 @@
 # Client driver configurations go here.
 config INTEL_RAPL_CORE
 	tristate
+	depends on PCI
+	select IOSF_MBI
 
 config INTEL_RAPL
 	tristate "Intel RAPL Support via MSR Interface"
-	depends on X86 && IOSF_MBI
+	depends on X86 && PCI
 	select INTEL_RAPL_CORE
 	help
 	  This enables support for the Intel Running Average Power Limit (RAPL)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/powercap/intel_rapl_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/powercap/intel_rapl_common.c
@@ -938,6 +938,9 @@
 		y = value & 0x1f;
 		value = (1 << y) * (4 + f) * rp->time_unit / 4;
 	} else {
+		if (value < rp->time_unit)
+			return 0;
+
 		do_div(value, rp->time_unit);
 		y = ilog2(value);
 		f = div64_u64(4 * (value - (1 << y)), 1 << y);
@@ -979,7 +982,6 @@
 	.check_unit = rapl_check_unit_core,
 	.set_floor_freq = set_floor_freq_default,
 	.compute_time_window = rapl_compute_time_window_core,
-	.dram_domain_energy_unit = 15300,
 	.psys_domain_energy_unit = 1000000000,
 };
 
@@ -1050,7 +1052,11 @@
 	X86_MATCH_INTEL_FAM6_MODEL(ROCKETLAKE,		&rapl_defaults_core),
 	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE,		&rapl_defaults_core),
 	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L,		&rapl_defaults_core),
+	X86_MATCH_INTEL_FAM6_MODEL(RAPTORLAKE,		&rapl_defaults_core),
+	X86_MATCH_INTEL_FAM6_MODEL(RAPTORLAKE_P,        &rapl_defaults_core),
+	X86_MATCH_INTEL_FAM6_MODEL(RAPTORLAKE_S,	&rapl_defaults_core),
 	X86_MATCH_INTEL_FAM6_MODEL(SAPPHIRERAPIDS_X,	&rapl_defaults_spr_server),
+	X86_MATCH_INTEL_FAM6_MODEL(EMERALDRAPIDS_X,	&rapl_defaults_spr_server),
 	X86_MATCH_INTEL_FAM6_MODEL(LAKEFIELD,		&rapl_defaults_core),
 
 	X86_MATCH_INTEL_FAM6_MODEL(ATOM_SILVERMONT,	&rapl_defaults_byt),
@@ -1455,7 +1461,7 @@
 
 	id = x86_match_cpu(rapl_ids);
 	if (!id) {
-		pr_err("driver does not support CPU family %d model %d\n",
+		pr_info("driver does not support CPU family %d model %d\n",
 		       boot_cpu_data.x86, boot_cpu_data.x86_model);
 
 		return -ENODEV;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/powercap/intel_rapl_msr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/powercap/intel_rapl_msr.c
@@ -22,7 +22,6 @@
 #include <linux/processor.h>
 #include <linux/platform_device.h>
 
-#include <asm/iosf_mbi.h>
 #include <asm/cpu_device_id.h>
 #include <asm/intel-family.h>
 
@@ -137,9 +136,9 @@
 
 /* List of verified CPUs. */
 static const struct x86_cpu_id pl4_support_ids[] = {
-	{ X86_VENDOR_INTEL, 6, INTEL_FAM6_TIGERLAKE_L, X86_FEATURE_ANY },
-	{ X86_VENDOR_INTEL, 6, INTEL_FAM6_ALDERLAKE, X86_FEATURE_ANY },
-	{ X86_VENDOR_INTEL, 6, INTEL_FAM6_ALDERLAKE_L, X86_FEATURE_ANY },
+	X86_MATCH_INTEL_FAM6_MODEL(TIGERLAKE_L, NULL),
+	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE, NULL),
+	X86_MATCH_INTEL_FAM6_MODEL(ALDERLAKE_L, NULL),
 	{}
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/powercap/powercap_sys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/powercap/powercap_sys.c
@@ -529,9 +529,6 @@
 	power_zone->name = kstrdup(name, GFP_KERNEL);
 	if (!power_zone->name)
 		goto err_name_alloc;
-	dev_set_name(&power_zone->dev, "%s:%x",
-					dev_name(power_zone->dev.parent),
-					power_zone->id);
 	power_zone->constraints = kcalloc(nr_constraints,
 					  sizeof(*power_zone->constraints),
 					  GFP_KERNEL);
@@ -554,9 +551,16 @@
 	power_zone->dev_attr_groups[0] = &power_zone->dev_zone_attr_group;
 	power_zone->dev_attr_groups[1] = NULL;
 	power_zone->dev.groups = power_zone->dev_attr_groups;
+	dev_set_name(&power_zone->dev, "%s:%x",
+					dev_name(power_zone->dev.parent),
+					power_zone->id);
 	result = device_register(&power_zone->dev);
-	if (result)
-		goto err_dev_ret;
+	if (result) {
+		put_device(&power_zone->dev);
+		mutex_unlock(&control_type->lock);
+
+		return ERR_PTR(result);
+	}
 
 	control_type->nr_zones++;
 	mutex_unlock(&control_type->lock);
@@ -622,8 +626,7 @@
 	dev_set_name(&control_type->dev, "%s", name);
 	result = device_register(&control_type->dev);
 	if (result) {
-		if (control_type->allocated)
-			kfree(control_type);
+		put_device(&control_type->dev);
 		return ERR_PTR(result);
 	}
 	idr_init(&control_type->idr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/clients/pps-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/clients/pps-gpio.c
@@ -169,7 +169,7 @@
 	/* GPIO setup */
 	ret = pps_gpio_setup(dev);
 	if (ret)
-		return -EINVAL;
+		return ret;
 
 	/* IRQ setup */
 	ret = gpiod_to_irq(data->gpio_pin);
@@ -214,8 +214,8 @@
 		return -EINVAL;
 	}
 
-	dev_info(data->pps->dev, "Registered IRQ %d as PPS source\n",
-		 data->irq);
+	dev_dbg(&data->pps->dev, "Registered IRQ %d as PPS source\n",
+		data->irq);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/clients/pps-ktimer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/clients/pps-ktimer.c
@@ -56,7 +56,7 @@
 
 static void __exit pps_ktimer_exit(void)
 {
-	dev_info(pps->dev, "ktimer PPS source unregistered\n");
+	dev_dbg(&pps->dev, "ktimer PPS source unregistered\n");
 
 	del_timer_sync(&ktimer);
 	pps_unregister_source(pps);
@@ -74,7 +74,7 @@
 	timer_setup(&ktimer, pps_ktimer_event, 0);
 	mod_timer(&ktimer, jiffies + HZ);
 
-	dev_info(pps->dev, "ktimer PPS source registered\n");
+	dev_dbg(&pps->dev, "ktimer PPS source registered\n");
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/clients/pps-ldisc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/clients/pps-ldisc.c
@@ -32,7 +32,7 @@
 	pps_event(pps, &ts, status ? PPS_CAPTUREASSERT :
 			PPS_CAPTURECLEAR, NULL);
 
-	dev_dbg(pps->dev, "PPS %s at %lu\n",
+	dev_dbg(&pps->dev, "PPS %s at %lu\n",
 			status ? "assert" : "clear", jiffies);
 }
 
@@ -69,7 +69,7 @@
 		goto err_unregister;
 	}
 
-	dev_info(pps->dev, "source \"%s\" added\n", info.path);
+	dev_dbg(&pps->dev, "source \"%s\" added\n", info.path);
 
 	return 0;
 
@@ -89,7 +89,7 @@
 	if (WARN_ON(!pps))
 		return;
 
-	dev_info(pps->dev, "removed\n");
+	dev_info(&pps->dev, "removed\n");
 	pps_unregister_source(pps);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/clients/pps_parport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/clients/pps_parport.c
@@ -81,7 +81,7 @@
 	/* check the signal (no signal means the pulse is lost this time) */
 	if (!signal_is_set(port)) {
 		local_irq_restore(flags);
-		dev_err(dev->pps->dev, "lost the signal\n");
+		dev_err(&dev->pps->dev, "lost the signal\n");
 		goto out_assert;
 	}
 
@@ -98,7 +98,7 @@
 	/* timeout */
 	dev->cw_err++;
 	if (dev->cw_err >= CLEAR_WAIT_MAX_ERRORS) {
-		dev_err(dev->pps->dev, "disabled clear edge capture after %d"
+		dev_err(&dev->pps->dev, "disabled clear edge capture after %d"
 				" timeouts\n", dev->cw_err);
 		dev->cw = 0;
 		dev->cw_err = 0;
@@ -148,7 +148,10 @@
 		return;
 	}
 
-	index = ida_simple_get(&pps_client_index, 0, 0, GFP_KERNEL);
+	index = ida_alloc(&pps_client_index, GFP_KERNEL);
+	if (index < 0)
+		goto err_free_device;
+
 	memset(&pps_client_cb, 0, sizeof(pps_client_cb));
 	pps_client_cb.private = device;
 	pps_client_cb.irq_func = parport_irq;
@@ -159,7 +162,7 @@
 						    index);
 	if (!device->pardev) {
 		pr_err("couldn't register with %s\n", port->name);
-		goto err_free;
+		goto err_free_ida;
 	}
 
 	if (parport_claim_or_block(device->pardev) < 0) {
@@ -187,8 +190,9 @@
 	parport_release(device->pardev);
 err_unregister_dev:
 	parport_unregister_device(device->pardev);
-err_free:
-	ida_simple_remove(&pps_client_index, index);
+err_free_ida:
+	ida_free(&pps_client_index, index);
+err_free_device:
 	kfree(device);
 }
 
@@ -208,7 +212,7 @@
 	pps_unregister_source(device->pps);
 	parport_release(pardev);
 	parport_unregister_device(pardev);
-	ida_simple_remove(&pps_client_index, device->index);
+	ida_free(&pps_client_index, device->index);
 	kfree(device);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/kapi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/kapi.c
@@ -41,7 +41,7 @@
 static void pps_echo_client_default(struct pps_device *pps, int event,
 		void *data)
 {
-	dev_info(pps->dev, "echo %s %s\n",
+	dev_info(&pps->dev, "echo %s %s\n",
 		event & PPS_CAPTUREASSERT ? "assert" : "",
 		event & PPS_CAPTURECLEAR ? "clear" : "");
 }
@@ -112,7 +112,7 @@
 		goto kfree_pps;
 	}
 
-	dev_info(pps->dev, "new PPS source %s\n", info->name);
+	dev_dbg(&pps->dev, "new PPS source %s\n", info->name);
 
 	return pps;
 
@@ -166,7 +166,7 @@
 	/* check event type */
 	BUG_ON((event & (PPS_CAPTUREASSERT | PPS_CAPTURECLEAR)) == 0);
 
-	dev_dbg(pps->dev, "PPS event at %lld.%09ld\n",
+	dev_dbg(&pps->dev, "PPS event at %lld.%09ld\n",
 			(s64)ts->ts_real.tv_sec, ts->ts_real.tv_nsec);
 
 	timespec_to_pps_ktime(&ts_real, ts->ts_real);
@@ -188,7 +188,7 @@
 		/* Save the time stamp */
 		pps->assert_tu = ts_real;
 		pps->assert_sequence++;
-		dev_dbg(pps->dev, "capture assert seq #%u\n",
+		dev_dbg(&pps->dev, "capture assert seq #%u\n",
 			pps->assert_sequence);
 
 		captured = ~0;
@@ -202,7 +202,7 @@
 		/* Save the time stamp */
 		pps->clear_tu = ts_real;
 		pps->clear_sequence++;
-		dev_dbg(pps->dev, "capture clear seq #%u\n",
+		dev_dbg(&pps->dev, "capture clear seq #%u\n",
 			pps->clear_sequence);
 
 		captured = ~0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/kc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/kc.c
@@ -43,11 +43,11 @@
 			pps_kc_hardpps_mode = 0;
 			pps_kc_hardpps_dev = NULL;
 			spin_unlock_irq(&pps_kc_hardpps_lock);
-			dev_info(pps->dev, "unbound kernel"
+			dev_info(&pps->dev, "unbound kernel"
 					" consumer\n");
 		} else {
 			spin_unlock_irq(&pps_kc_hardpps_lock);
-			dev_err(pps->dev, "selected kernel consumer"
+			dev_err(&pps->dev, "selected kernel consumer"
 					" is not bound\n");
 			return -EINVAL;
 		}
@@ -57,11 +57,11 @@
 			pps_kc_hardpps_mode = bind_args->edge;
 			pps_kc_hardpps_dev = pps;
 			spin_unlock_irq(&pps_kc_hardpps_lock);
-			dev_info(pps->dev, "bound kernel consumer: "
+			dev_info(&pps->dev, "bound kernel consumer: "
 				"edge=0x%x\n", bind_args->edge);
 		} else {
 			spin_unlock_irq(&pps_kc_hardpps_lock);
-			dev_err(pps->dev, "another kernel consumer"
+			dev_err(&pps->dev, "another kernel consumer"
 					" is already bound\n");
 			return -EINVAL;
 		}
@@ -83,7 +83,7 @@
 		pps_kc_hardpps_mode = 0;
 		pps_kc_hardpps_dev = NULL;
 		spin_unlock_irq(&pps_kc_hardpps_lock);
-		dev_info(pps->dev, "unbound kernel consumer"
+		dev_info(&pps->dev, "unbound kernel consumer"
 				" on device removal\n");
 	} else
 		spin_unlock_irq(&pps_kc_hardpps_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pps/pps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pps/pps.c
@@ -25,7 +25,7 @@
  * Local variables
  */
 
-static dev_t pps_devt;
+static int pps_major;
 static struct class *pps_class;
 
 static DEFINE_MUTEX(pps_idr_lock);
@@ -62,7 +62,7 @@
 	else {
 		unsigned long ticks;
 
-		dev_dbg(pps->dev, "timeout %lld.%09d\n",
+		dev_dbg(&pps->dev, "timeout %lld.%09d\n",
 				(long long) fdata->timeout.sec,
 				fdata->timeout.nsec);
 		ticks = fdata->timeout.sec * HZ;
@@ -80,7 +80,7 @@
 
 	/* Check for pending signals */
 	if (err == -ERESTARTSYS) {
-		dev_dbg(pps->dev, "pending signal caught\n");
+		dev_dbg(&pps->dev, "pending signal caught\n");
 		return -EINTR;
 	}
 
@@ -98,7 +98,7 @@
 
 	switch (cmd) {
 	case PPS_GETPARAMS:
-		dev_dbg(pps->dev, "PPS_GETPARAMS\n");
+		dev_dbg(&pps->dev, "PPS_GETPARAMS\n");
 
 		spin_lock_irq(&pps->lock);
 
@@ -114,7 +114,7 @@
 		break;
 
 	case PPS_SETPARAMS:
-		dev_dbg(pps->dev, "PPS_SETPARAMS\n");
+		dev_dbg(&pps->dev, "PPS_SETPARAMS\n");
 
 		/* Check the capabilities */
 		if (!capable(CAP_SYS_TIME))
@@ -124,14 +124,14 @@
 		if (err)
 			return -EFAULT;
 		if (!(params.mode & (PPS_CAPTUREASSERT | PPS_CAPTURECLEAR))) {
-			dev_dbg(pps->dev, "capture mode unspecified (%x)\n",
+			dev_dbg(&pps->dev, "capture mode unspecified (%x)\n",
 								params.mode);
 			return -EINVAL;
 		}
 
 		/* Check for supported capabilities */
 		if ((params.mode & ~pps->info.mode) != 0) {
-			dev_dbg(pps->dev, "unsupported capabilities (%x)\n",
+			dev_dbg(&pps->dev, "unsupported capabilities (%x)\n",
 								params.mode);
 			return -EINVAL;
 		}
@@ -144,7 +144,7 @@
 		/* Restore the read only parameters */
 		if ((params.mode & (PPS_TSFMT_TSPEC | PPS_TSFMT_NTPFP)) == 0) {
 			/* section 3.3 of RFC 2783 interpreted */
-			dev_dbg(pps->dev, "time format unspecified (%x)\n",
+			dev_dbg(&pps->dev, "time format unspecified (%x)\n",
 								params.mode);
 			pps->params.mode |= PPS_TSFMT_TSPEC;
 		}
@@ -165,7 +165,7 @@
 		break;
 
 	case PPS_GETCAP:
-		dev_dbg(pps->dev, "PPS_GETCAP\n");
+		dev_dbg(&pps->dev, "PPS_GETCAP\n");
 
 		err = put_user(pps->info.mode, iuarg);
 		if (err)
@@ -176,7 +176,7 @@
 	case PPS_FETCH: {
 		struct pps_fdata fdata;
 
-		dev_dbg(pps->dev, "PPS_FETCH\n");
+		dev_dbg(&pps->dev, "PPS_FETCH\n");
 
 		err = copy_from_user(&fdata, uarg, sizeof(struct pps_fdata));
 		if (err)
@@ -206,7 +206,7 @@
 	case PPS_KC_BIND: {
 		struct pps_bind_args bind_args;
 
-		dev_dbg(pps->dev, "PPS_KC_BIND\n");
+		dev_dbg(&pps->dev, "PPS_KC_BIND\n");
 
 		/* Check the capabilities */
 		if (!capable(CAP_SYS_TIME))
@@ -218,7 +218,7 @@
 
 		/* Check for supported capabilities */
 		if ((bind_args.edge & ~pps->info.mode) != 0) {
-			dev_err(pps->dev, "unsupported capabilities (%x)\n",
+			dev_err(&pps->dev, "unsupported capabilities (%x)\n",
 					bind_args.edge);
 			return -EINVAL;
 		}
@@ -227,7 +227,7 @@
 		if (bind_args.tsformat != PPS_TSFMT_TSPEC ||
 				(bind_args.edge & ~PPS_CAPTUREBOTH) != 0 ||
 				bind_args.consumer != PPS_KC_HARDPPS) {
-			dev_err(pps->dev, "invalid kernel consumer bind"
+			dev_err(&pps->dev, "invalid kernel consumer bind"
 					" parameters (%x)\n", bind_args.edge);
 			return -EINVAL;
 		}
@@ -259,7 +259,7 @@
 		struct pps_fdata fdata;
 		int err;
 
-		dev_dbg(pps->dev, "PPS_FETCH\n");
+		dev_dbg(&pps->dev, "PPS_FETCH\n");
 
 		err = copy_from_user(&compat, uarg, sizeof(struct pps_fdata_compat));
 		if (err)
@@ -296,20 +296,36 @@
 #define pps_cdev_compat_ioctl	NULL
 #endif
 
+static struct pps_device *pps_idr_get(unsigned long id)
+{
+	struct pps_device *pps;
+
+	mutex_lock(&pps_idr_lock);
+	pps = idr_find(&pps_idr, id);
+	if (pps)
+		get_device(&pps->dev);
+
+	mutex_unlock(&pps_idr_lock);
+	return pps;
+}
+
 static int pps_cdev_open(struct inode *inode, struct file *file)
 {
-	struct pps_device *pps = container_of(inode->i_cdev,
-						struct pps_device, cdev);
+	struct pps_device *pps = pps_idr_get(iminor(inode));
+
+	if (!pps)
+		return -ENODEV;
+
 	file->private_data = pps;
-	kobject_get(&pps->dev->kobj);
 	return 0;
 }
 
 static int pps_cdev_release(struct inode *inode, struct file *file)
 {
-	struct pps_device *pps = container_of(inode->i_cdev,
-						struct pps_device, cdev);
-	kobject_put(&pps->dev->kobj);
+	struct pps_device *pps = file->private_data;
+
+	WARN_ON(pps->id != iminor(inode));
+	put_device(&pps->dev);
 	return 0;
 }
 
@@ -332,22 +348,13 @@
 {
 	struct pps_device *pps = dev_get_drvdata(dev);
 
-	cdev_del(&pps->cdev);
-
-	/* Now we can release the ID for re-use */
 	pr_debug("deallocating pps%d\n", pps->id);
-	mutex_lock(&pps_idr_lock);
-	idr_remove(&pps_idr, pps->id);
-	mutex_unlock(&pps_idr_lock);
-
-	kfree(dev);
 	kfree(pps);
 }
 
 int pps_register_cdev(struct pps_device *pps)
 {
 	int err;
-	dev_t devt;
 
 	mutex_lock(&pps_idr_lock);
 	/*
@@ -364,40 +371,29 @@
 		goto out_unlock;
 	}
 	pps->id = err;
-	mutex_unlock(&pps_idr_lock);
-
-	devt = MKDEV(MAJOR(pps_devt), pps->id);
-
-	cdev_init(&pps->cdev, &pps_cdev_fops);
-	pps->cdev.owner = pps->info.owner;
 
-	err = cdev_add(&pps->cdev, devt, 1);
-	if (err) {
-		pr_err("%s: failed to add char device %d:%d\n",
-				pps->info.name, MAJOR(pps_devt), pps->id);
+	pps->dev.class = pps_class;
+	pps->dev.parent = pps->info.dev;
+	pps->dev.devt = MKDEV(pps_major, pps->id);
+	dev_set_drvdata(&pps->dev, pps);
+	dev_set_name(&pps->dev, "pps%d", pps->id);
+	err = device_register(&pps->dev);
+	if (err)
 		goto free_idr;
-	}
-	pps->dev = device_create(pps_class, pps->info.dev, devt, pps,
-							"pps%d", pps->id);
-	if (IS_ERR(pps->dev)) {
-		err = PTR_ERR(pps->dev);
-		goto del_cdev;
-	}
 
 	/* Override the release function with our own */
-	pps->dev->release = pps_device_destruct;
+	pps->dev.release = pps_device_destruct;
 
-	pr_debug("source %s got cdev (%d:%d)\n", pps->info.name,
-			MAJOR(pps_devt), pps->id);
+	pr_debug("source %s got cdev (%d:%d)\n", pps->info.name, pps_major,
+		 pps->id);
 
+	get_device(&pps->dev);
+	mutex_unlock(&pps_idr_lock);
 	return 0;
 
-del_cdev:
-	cdev_del(&pps->cdev);
-
 free_idr:
-	mutex_lock(&pps_idr_lock);
 	idr_remove(&pps_idr, pps->id);
+	put_device(&pps->dev);
 out_unlock:
 	mutex_unlock(&pps_idr_lock);
 	return err;
@@ -407,7 +403,13 @@
 {
 	pr_debug("unregistering pps%d\n", pps->id);
 	pps->lookup_cookie = NULL;
-	device_destroy(pps_class, pps->dev->devt);
+	device_destroy(pps_class, pps->dev.devt);
+
+	/* Now we can release the ID for re-use */
+	mutex_lock(&pps_idr_lock);
+	idr_remove(&pps_idr, pps->id);
+	put_device(&pps->dev);
+	mutex_unlock(&pps_idr_lock);
 }
 
 /*
@@ -427,6 +429,11 @@
  * so that it will not be used again, even if the pps device cannot
  * be removed from the idr due to pending references holding the minor
  * number in use.
+ *
+ * Since pps_idr holds a reference to the device, the returned
+ * pps_device is guaranteed to be valid until pps_unregister_cdev() is
+ * called on it. But after calling pps_unregister_cdev(), it may be
+ * freed at any time.
  */
 struct pps_device *pps_lookup_dev(void const *cookie)
 {
@@ -449,13 +456,11 @@
 static void __exit pps_exit(void)
 {
 	class_destroy(pps_class);
-	unregister_chrdev_region(pps_devt, PPS_MAX_SOURCES);
+	__unregister_chrdev(pps_major, 0, PPS_MAX_SOURCES, "pps");
 }
 
 static int __init pps_init(void)
 {
-	int err;
-
 	pps_class = class_create(THIS_MODULE, "pps");
 	if (IS_ERR(pps_class)) {
 		pr_err("failed to allocate class\n");
@@ -463,8 +468,9 @@
 	}
 	pps_class->dev_groups = pps_groups;
 
-	err = alloc_chrdev_region(&pps_devt, 0, PPS_MAX_SOURCES, "pps");
-	if (err < 0) {
+	pps_major = __register_chrdev(0, 0, PPS_MAX_SOURCES, "pps",
+				      &pps_cdev_fops);
+	if (pps_major < 0) {
 		pr_err("failed to allocate char device region\n");
 		goto remove_class;
 	}
@@ -477,8 +483,7 @@
 
 remove_class:
 	class_destroy(pps_class);
-
-	return err;
+	return pps_major;
 }
 
 subsys_initcall(pps_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/Kconfig
@@ -167,6 +167,16 @@
 	  To compile this driver as a module, choose M here: the module
 	  will be called ptp_vmw.
 
+config PTP_1588_CLOCK_XILINX
+	tristate "XILINX PTP clock"
+	depends on PTP_1588_CLOCK
+	help
+	  This driver adds support for Xilinx PTP clock. It provides
+	  timer-syncer support with time and fine adjustment capabilities.
+
+	  It is usually used with Xilinx AXI Ethernet driver with HW
+	  timestamping support.
+
 config PTP_1588_CLOCK_OCP
 	tristate "OpenCompute TimeCard as PTP clock"
 	depends on PTP_1588_CLOCK
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/Makefile
@@ -11,6 +11,7 @@
 obj-$(CONFIG_PTP_1588_CLOCK_INES)	+= ptp_ines.o
 obj-$(CONFIG_PTP_1588_CLOCK_PCH)	+= ptp_pch.o
 obj-$(CONFIG_PTP_1588_CLOCK_KVM)	+= ptp_kvm.o
+obj-$(CONFIG_PTP_1588_CLOCK_XILINX)	+= ptp_xilinx.o
 obj-$(CONFIG_PTP_1588_CLOCK_QORIQ)	+= ptp-qoriq.o
 ptp-qoriq-y				+= ptp_qoriq.o
 ptp-qoriq-$(CONFIG_DEBUG_FS)		+= ptp_qoriq_debugfs.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_chardev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_chardev.c
@@ -4,6 +4,7 @@
  *
  * Copyright (C) 2010 OMICRON electronics GmbH
  */
+#include <linux/compat.h>
 #include <linux/module.h>
 #include <linux/posix-clock.h>
 #include <linux/poll.h>
@@ -84,7 +85,8 @@
 	}
 
 	if (info->verify(info, pin, func, chan)) {
-		pr_err("driver cannot use function %u on pin %u\n", func, chan);
+		pr_err("driver cannot use function %u and channel %u on pin %u\n",
+		       func, chan, pin);
 		return -EOPNOTSUPP;
 	}
 
@@ -123,6 +125,9 @@
 	struct timespec64 ts;
 	int enable, err = 0;
 
+	if (in_compat_syscall() && cmd != PTP_ENABLE_PPS && cmd != PTP_ENABLE_PPS2)
+		arg = (unsigned long)compat_ptr(arg);
+
 	switch (cmd) {
 
 	case PTP_CLOCK_GETCAPS:
@@ -487,7 +492,8 @@
 
 	for (i = 0; i < cnt; i++) {
 		event[i] = queue->buf[queue->head];
-		queue->head = (queue->head + 1) % PTP_MAX_TIMESTAMPS;
+		/* Paired with READ_ONCE() in queue_cnt() */
+		WRITE_ONCE(queue->head, (queue->head + 1) % PTP_MAX_TIMESTAMPS);
 	}
 
 	spin_unlock_irqrestore(&queue->lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_clock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_clock.c
@@ -56,10 +56,11 @@
 	dst->t.sec = seconds;
 	dst->t.nsec = remainder;
 
+	/* Both WRITE_ONCE() are paired with READ_ONCE() in queue_cnt() */
 	if (!queue_free(queue))
-		queue->head = (queue->head + 1) % PTP_MAX_TIMESTAMPS;
+		WRITE_ONCE(queue->head, (queue->head + 1) % PTP_MAX_TIMESTAMPS);
 
-	queue->tail = (queue->tail + 1) % PTP_MAX_TIMESTAMPS;
+	WRITE_ONCE(queue->tail, (queue->tail + 1) % PTP_MAX_TIMESTAMPS);
 
 	spin_unlock_irqrestore(&queue->lock, flags);
 }
@@ -135,7 +136,8 @@
 			err = ops->adjfine(ops, tx->freq);
 		else
 			err = ops->adjfreq(ops, ppb);
-		ptp->dialed_frequency = tx->freq;
+		if (!err)
+			ptp->dialed_frequency = tx->freq;
 	} else if (tx->modes & ADJ_OFFSET) {
 		if (ops->adjphase) {
 			s32 offset = tx->offset;
@@ -169,6 +171,9 @@
 {
 	struct ptp_clock *ptp = container_of(dev, struct ptp_clock, dev);
 
+	/* Release the clock's resources. */
+	if (ptp->pps_source)
+		pps_unregister_source(ptp->pps_source);
 	ptp_cleanup_pin_groups(ptp);
 	kfree(ptp->vclock_index);
 	mutex_destroy(&ptp->tsevq_mux);
@@ -178,6 +183,11 @@
 	kfree(ptp);
 }
 
+static int ptp_enable(struct ptp_clock_info *ptp, struct ptp_clock_request *request, int on)
+{
+	return -EOPNOTSUPP;
+}
+
 static void ptp_aux_kworker(struct kthread_work *work)
 {
 	struct ptp_clock *ptp = container_of(work, struct ptp_clock,
@@ -225,6 +235,9 @@
 	mutex_init(&ptp->n_vclocks_mux);
 	init_waitqueue_head(&ptp->tsev_wq);
 
+	if (!ptp->info->enable)
+		ptp->info->enable = ptp_enable;
+
 	if (ptp->info->do_aux_work) {
 		kthread_init_delayed_work(&ptp->aux_work, ptp_aux_kworker);
 		ptp->kworker = kthread_create_worker(0, "ptp%d", ptp->index);
@@ -317,11 +330,18 @@
 }
 EXPORT_SYMBOL(ptp_clock_register);
 
+static int unregister_vclock(struct device *dev, void *data)
+{
+	struct ptp_clock *ptp = dev_get_drvdata(dev);
+
+	ptp_vclock_unregister(info_to_vclock(ptp->info));
+	return 0;
+}
+
 int ptp_clock_unregister(struct ptp_clock *ptp)
 {
 	if (ptp_vclock_in_use(ptp)) {
-		pr_err("ptp: virtual clock in use\n");
-		return -EBUSY;
+		device_for_each_child(&ptp->dev, NULL, unregister_vclock);
 	}
 
 	ptp->defunct = 1;
@@ -331,11 +351,6 @@
 		kthread_cancel_delayed_work_sync(&ptp->aux_work);
 		kthread_destroy_worker(ptp->kworker);
 	}
-
-	/* Release the clock's resources. */
-	if (ptp->pps_source)
-		pps_unregister_source(ptp->pps_source);
-
 	posix_clock_unregister(&ptp->clock);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_kvm_arm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_kvm_arm.c
@@ -22,6 +22,10 @@
 	return 0;
 }
 
+void kvm_arch_ptp_exit(void)
+{
+}
+
 int kvm_arch_ptp_get_clock(struct timespec64 *ts)
 {
 	return kvm_arch_ptp_get_crosststamp(NULL, ts, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_kvm_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_kvm_common.c
@@ -130,6 +130,7 @@
 static void __exit ptp_kvm_exit(void)
 {
 	ptp_clock_unregister(kvm_ptp_clock.ptp_clock);
+	kvm_arch_ptp_exit();
 }
 
 static int __init ptp_kvm_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_kvm_x86.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_kvm_x86.c
@@ -14,27 +14,64 @@
 #include <uapi/linux/kvm_para.h>
 #include <linux/ptp_clock_kernel.h>
 #include <linux/ptp_kvm.h>
+#include <linux/set_memory.h>
 
 static phys_addr_t clock_pair_gpa;
-static struct kvm_clock_pairing clock_pair;
+static struct kvm_clock_pairing clock_pair_glbl;
+static struct kvm_clock_pairing *clock_pair;
 
 int kvm_arch_ptp_init(void)
 {
+	struct page *p;
 	long ret;
 
 	if (!kvm_para_available())
-		return -ENODEV;
+		return -EOPNOTSUPP;
+
+	if (cc_platform_has(CC_ATTR_GUEST_MEM_ENCRYPT)) {
+		p = alloc_page(GFP_KERNEL | __GFP_ZERO);
+		if (!p)
+			return -ENOMEM;
+
+		clock_pair = page_address(p);
+		ret = set_memory_decrypted((unsigned long)clock_pair, 1);
+		if (ret) {
+			__free_page(p);
+			clock_pair = NULL;
+			goto nofree;
+		}
+	} else {
+		clock_pair = &clock_pair_glbl;
+	}
 
-	clock_pair_gpa = slow_virt_to_phys(&clock_pair);
-	if (!pvclock_get_pvti_cpu0_va())
-		return -ENODEV;
+	clock_pair_gpa = slow_virt_to_phys(clock_pair);
+	if (!pvclock_get_pvti_cpu0_va()) {
+		ret = -EOPNOTSUPP;
+		goto err;
+	}
 
 	ret = kvm_hypercall2(KVM_HC_CLOCK_PAIRING, clock_pair_gpa,
 			     KVM_CLOCK_PAIRING_WALLCLOCK);
-	if (ret == -KVM_ENOSYS)
-		return -ENODEV;
+	if (ret == -KVM_ENOSYS) {
+		ret = -EOPNOTSUPP;
+		goto err;
+	}
 
 	return ret;
+
+err:
+	kvm_arch_ptp_exit();
+nofree:
+	return ret;
+}
+
+void kvm_arch_ptp_exit(void)
+{
+	if (cc_platform_has(CC_ATTR_GUEST_MEM_ENCRYPT)) {
+		WARN_ON(set_memory_encrypted((unsigned long)clock_pair, 1));
+		free_page((unsigned long)clock_pair);
+		clock_pair = NULL;
+	}
 }
 
 int kvm_arch_ptp_get_clock(struct timespec64 *ts)
@@ -49,8 +86,8 @@
 		return -EOPNOTSUPP;
 	}
 
-	ts->tv_sec = clock_pair.sec;
-	ts->tv_nsec = clock_pair.nsec;
+	ts->tv_sec = clock_pair->sec;
+	ts->tv_nsec = clock_pair->nsec;
 
 	return 0;
 }
@@ -81,9 +118,9 @@
 			pr_err_ratelimited("clock pairing hypercall ret %lu\n", ret);
 			return -EOPNOTSUPP;
 		}
-		tspec->tv_sec = clock_pair.sec;
-		tspec->tv_nsec = clock_pair.nsec;
-		*cycle = __pvclock_read_cycles(src, clock_pair.tsc);
+		tspec->tv_sec = clock_pair->sec;
+		tspec->tv_nsec = clock_pair->nsec;
+		*cycle = __pvclock_read_cycles(src, clock_pair->tsc);
 	} while (pvclock_read_retry(src, version));
 
 	*cs = &kvm_clock;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_ocp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_ocp.c
@@ -1049,10 +1049,11 @@
 	if (!ext)
 		return -ENOMEM;
 
-	err = -EINVAL;
 	ext->mem = ptp_ocp_get_mem(bp, r);
-	if (!ext->mem)
+	if (IS_ERR(ext->mem)) {
+		err = PTR_ERR(ext->mem);
 		goto out;
+	}
 
 	ext->bp = bp;
 	ext->info = r->extra;
@@ -1122,8 +1123,8 @@
 	void __iomem *mem;
 
 	mem = ptp_ocp_get_mem(bp, r);
-	if (!mem)
-		return -EINVAL;
+	if (IS_ERR(mem))
+		return PTR_ERR(mem);
 
 	bp_assign_entry(bp, r, mem);
 
@@ -1291,7 +1292,6 @@
 	return 0;
 
 out:
-	ptp_ocp_dev_release(&bp->dev);
 	put_device(&bp->dev);
 	return err;
 }
@@ -1341,7 +1341,7 @@
 
 	pps = pps_lookup_dev(bp->ptp);
 	if (pps)
-		ptp_ocp_symlink(bp, pps->dev, "pps");
+		ptp_ocp_symlink(bp, &pps->dev, "pps");
 
 	if (device_add_groups(&bp->dev, timecard_groups))
 		pr_err("device add groups failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_private.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_private.h
@@ -74,9 +74,13 @@
  * that a writer might concurrently increment the tail does not
  * matter, since the queue remains nonempty nonetheless.
  */
-static inline int queue_cnt(struct timestamp_event_queue *q)
+static inline int queue_cnt(const struct timestamp_event_queue *q)
 {
-	int cnt = q->tail - q->head;
+	/*
+	 * Paired with WRITE_ONCE() in enqueue_external_timestamp(),
+	 * ptp_read(), extts_fifo_show().
+	 */
+	int cnt = READ_ONCE(q->tail) - READ_ONCE(q->head);
 	return cnt < 0 ? PTP_MAX_TIMESTAMPS + cnt : cnt;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_qoriq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_qoriq.c
@@ -601,7 +601,7 @@
 	return 0;
 
 no_clock:
-	iounmap(ptp_qoriq->base);
+	iounmap(base);
 no_ioremap:
 	release_resource(ptp_qoriq->rsrc);
 no_resource:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_sysfs.c
@@ -14,7 +14,7 @@
 			       struct device_attribute *attr, char *page)
 {
 	struct ptp_clock *ptp = dev_get_drvdata(dev);
-	return snprintf(page, PAGE_SIZE-1, "%s\n", ptp->info->name);
+	return sysfs_emit(page, "%s\n", ptp->info->name);
 }
 static DEVICE_ATTR_RO(clock_name);
 
@@ -79,7 +79,8 @@
 	qcnt = queue_cnt(queue);
 	if (qcnt) {
 		event = queue->buf[queue->head];
-		queue->head = (queue->head + 1) % PTP_MAX_TIMESTAMPS;
+		/* Paired with READ_ONCE() in queue_cnt() */
+		WRITE_ONCE(queue->head, (queue->head + 1) % PTP_MAX_TIMESTAMPS);
 	}
 	spin_unlock_irqrestore(&queue->lock, flags);
 
@@ -279,8 +280,7 @@
 	if (max < ptp->n_vclocks)
 		goto out;
 
-	size = sizeof(int) * max;
-	vclock_index = kzalloc(size, GFP_KERNEL);
+	vclock_index = kcalloc(max, sizeof(int), GFP_KERNEL);
 	if (!vclock_index) {
 		err = -ENOMEM;
 		goto out;
@@ -387,7 +387,7 @@
 
 	mutex_unlock(&ptp->pincfg_mux);
 
-	return snprintf(page, PAGE_SIZE, "%u %u\n", func, chan);
+	return sysfs_emit(page, "%u %u\n", func, chan);
 }
 
 static ssize_t ptp_pin_store(struct device *dev, struct device_attribute *attr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_vclock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_vclock.c
@@ -185,8 +185,8 @@
 }
 EXPORT_SYMBOL(ptp_get_vclocks_index);
 
-void ptp_convert_timestamp(struct skb_shared_hwtstamps *hwtstamps,
-			   int vclock_index)
+ktime_t ptp_convert_timestamp(const struct skb_shared_hwtstamps *hwtstamps,
+			      int vclock_index)
 {
 	char name[PTP_CLOCK_NAME_LEN] = "";
 	struct ptp_vclock *vclock;
@@ -198,12 +198,12 @@
 	snprintf(name, PTP_CLOCK_NAME_LEN, "ptp%d", vclock_index);
 	dev = class_find_device_by_name(ptp_class, name);
 	if (!dev)
-		return;
+		return 0;
 
 	ptp = dev_get_drvdata(dev);
 	if (!ptp->is_virtual_clock) {
 		put_device(dev);
-		return;
+		return 0;
 	}
 
 	vclock = info_to_vclock(ptp->info);
@@ -215,7 +215,7 @@
 	spin_unlock_irqrestore(&vclock->lock, flags);
 
 	put_device(dev);
-	hwtstamps->hwtstamp = ns_to_ktime(ns);
+	return ns_to_ktime(ns);
 }
 EXPORT_SYMBOL(ptp_convert_timestamp);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ptp/ptp_xilinx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ptp/ptp_xilinx.c
@@ -0,0 +1,436 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx 1588 PTP timer syncer driver
+ *
+ * Copyright (c) 2020 Xilinx, Inc. All rights reserved.
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ptp_clock_kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of_irq.h>
+
+/* Register offset definitions */
+#define XPTPTIMER_TOD_CONFIG_OFFSET	0x0000
+#define XPTPTIMER_TOD_SNAPSHOT_OFFSET	0x0004
+#define XPTPTIMER_IER_OFFSET		0x0008
+#define XPTPTIMER_ISR_OFFSET		0x000C
+#define XPTPTIMER_TOD_SW_SEC_0_OFFSET	0x0010
+#define XPTPTIMER_TOD_SW_SEC_1_OFFSET	0x0014
+#define XPTPTIMER_TOD_SW_NS_OFFSET	0x0018
+#define XPTPTIMER_TOD_SW_LOAD_OFFSET	0x001C
+#define XPTPTIMER_TOD_SEC_SYS_OFST_0_OFFSET	0x0028
+#define XPTPTIMER_TOD_SEC_SYS_OFST_1_OFFSET	0x002C
+#define XPTPTIMER_TOD_NS_SYS_OFST_OFFSET	0x0030
+#define TOD_SYS_PERIOD_0                0x0130
+#define TOD_SYS_PERIOD_1                0x0134
+
+#define XPTPTIMER_SYS_SEC_0_OFFSET	0x0100
+#define XPTPTIMER_SYS_SEC_1_OFFSET	0x0104
+#define XPTPTIMER_SYS_NS_OFFSET		0x0108
+
+#define XPTPTIMER_PORT_TX_PERIOD_0_OFFSET	0x0208
+#define XPTPTIMER_PORT_TX_PERIOD_1_OFFSET	0x020C
+#define XPTPTIMER_PORT_TX_NS_SNAP_OFFSET	0x0214
+#define XPTPTIMER_PORT_TX_SEC_0_SNAP_OFFSET	0x0218
+#define XPTPTIMER_PORT_TX_SEC_1_SNAP_OFFSET	0x021C
+#define XPTPTIMER_PORT_RX_PERIOD_0_OFFSET	0x0228
+#define XPTPTIMER_PORT_RX_PERIOD_1_OFFSET	0x022C
+#define XPTPTIMER_PORT_RX_NS_SNAP_OFFSET	0x0234
+#define XPTPTIMER_PORT_RX_SEC_0_SNAP_OFFSET	0x0238
+#define XPTPTIMER_PORT_RX_SEC_1_SNAP_OFFSET	0x023C
+#define PORT0_SEC_OFFSET_0                     0x0250
+#define PORT0_SEC_OFFSET_1                     0x0254
+#define PORT0_NS_OFFSET_0                      0x0258
+
+
+#define XPTPTIMER_CFG_MAIN_TOD_EN	BIT(0)
+#define XPTPTIMER_CFG_ENABLE_PORT0	BIT(16)
+#define XPTPTIMER_CFG_AUTO_REF	BIT(4)
+
+#define XPTPTIMER_MAX_SEC_SIZE		48
+#define XPTPTIMER_MAX_SEC_MASK		GENMASK(XPTPTIMER_MAX_SEC_SIZE - 1, 0)
+
+#define XPTPTIMER_TOD_OFFSET_NEG	BIT(47)
+
+#define XPTPTIMER_SNAPSHOT_MASK		BIT(0)
+#define XPTPTIMER_LOAD_TOD_MASK		BIT(0)
+#define XPTPTIMER_LOAD_OFFSET_MASK	BIT(1)
+
+/* TODO This should be derived from the system design */
+#define XPTPTIMER_CLOCK_PERIOD		4
+#define XPTPTIMER_PERIOD_SHIFT		48
+
+#define PPM_FRACTION	16
+
+struct xlnx_ptp_timer {
+	struct		device *dev;
+	void __iomem		*baseaddr;
+	struct ptp_clock	*ptp_clock;
+	struct ptp_clock_info	ptp_clock_info;
+	spinlock_t		reg_lock; /* For reg access */
+	u64			incr;
+	s64			timeoffset;
+	s32			static_delay;
+};
+
+/* I/O accessors */
+static inline u32 xlnx_ptp_ior(struct xlnx_ptp_timer *timer, off_t reg)
+{
+	return ioread32(timer->baseaddr + reg);
+}
+
+static inline void xlnx_ptp_iow(struct xlnx_ptp_timer *timer, off_t reg,
+				u32 value)
+{
+	iowrite32(value, (timer->baseaddr + reg));
+}
+
+/*
+ * Inline timer helpers
+ */
+static inline void xlnx_tod_read(struct xlnx_ptp_timer *timer,
+				 struct timespec64 *ts)
+{
+	u32 sech, secl, nsec;
+
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SNAPSHOT_OFFSET,
+		     XPTPTIMER_SNAPSHOT_MASK);
+
+	/* use TX port here */
+	nsec = xlnx_ptp_ior(timer, XPTPTIMER_PORT_TX_NS_SNAP_OFFSET);
+	secl = xlnx_ptp_ior(timer, XPTPTIMER_PORT_TX_SEC_0_SNAP_OFFSET);
+	sech = xlnx_ptp_ior(timer, XPTPTIMER_PORT_TX_SEC_1_SNAP_OFFSET);
+
+	ts->tv_nsec = nsec;
+	ts->tv_sec = (((u64)sech << 32) | secl) & XPTPTIMER_MAX_SEC_MASK;
+}
+
+static inline void xlnx_port_offset_write(struct xlnx_ptp_timer *timer,
+					  const struct timespec64 *ts)
+{
+	int i;
+
+	xlnx_ptp_iow(timer, PORT0_SEC_OFFSET_0,
+		     lower_32_bits(ts->tv_sec));
+	xlnx_ptp_iow(timer, PORT0_SEC_OFFSET_1,
+		     upper_32_bits(ts->tv_sec));
+	/*
+	 * Two writes are done to PORT0_NS_OFFSET_0 due to IP behavior which
+	 * uses the same as trigger to accept the whole offset value.
+	 */
+	for (i = 0; i < 2; i++) {
+		xlnx_ptp_iow(timer, PORT0_NS_OFFSET_0,
+			     (u32)(ts->tv_nsec));
+	}
+}
+
+static inline void xlnx_tod_offset_write(struct xlnx_ptp_timer *timer,
+					 const struct timespec64 *ts)
+{
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SEC_SYS_OFST_1_OFFSET,
+		     upper_32_bits(ts->tv_sec));
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SEC_SYS_OFST_0_OFFSET,
+		     lower_32_bits(ts->tv_sec));
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_NS_SYS_OFST_OFFSET,
+		     (u32)(ts->tv_nsec));
+
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SW_LOAD_OFFSET,
+		     XPTPTIMER_LOAD_OFFSET_MASK);
+}
+
+static inline void xlnx_tod_load_write(struct xlnx_ptp_timer *timer,
+				       const struct timespec64 *ts)
+{
+	struct timespec64 offset;
+
+	offset.tv_sec = 0;
+	offset.tv_nsec = 0;
+
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SW_SEC_1_OFFSET,
+		     upper_32_bits(ts->tv_sec));
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SW_SEC_0_OFFSET,
+		     lower_32_bits(ts->tv_sec));
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SW_NS_OFFSET, ts->tv_nsec);
+
+	/* Make sure offset registers are cleared */
+	xlnx_tod_offset_write(timer, &offset);
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SW_LOAD_OFFSET,
+		     XPTPTIMER_LOAD_OFFSET_MASK);
+
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SW_LOAD_OFFSET,
+		     XPTPTIMER_LOAD_TOD_MASK);
+	xlnx_port_offset_write(timer, &offset);
+	timer->timeoffset = 0;
+}
+
+static inline void xlnx_tod_period_write(struct xlnx_ptp_timer *timer, u64 adj)
+{
+	u32 adjhigh = upper_32_bits(adj);
+
+	xlnx_ptp_iow(timer, TOD_SYS_PERIOD_0, (u32)(adj));
+	xlnx_ptp_iow(timer, TOD_SYS_PERIOD_1, adjhigh);
+}
+
+static inline void xlnx_port_period_write(struct xlnx_ptp_timer *timer, u64 adj)
+{
+	u32 adjhigh = upper_32_bits(adj);
+
+	xlnx_ptp_iow(timer, XPTPTIMER_PORT_TX_PERIOD_0_OFFSET, (u32)(adj));
+	xlnx_ptp_iow(timer, XPTPTIMER_PORT_RX_PERIOD_0_OFFSET, (u32)(adj));
+	spin_lock(&timer->reg_lock);
+	xlnx_ptp_iow(timer, XPTPTIMER_PORT_TX_PERIOD_1_OFFSET, adjhigh);
+	xlnx_ptp_iow(timer, XPTPTIMER_PORT_RX_PERIOD_1_OFFSET, adjhigh);
+
+	spin_unlock(&timer->reg_lock);
+}
+
+/*
+ * PTP clock operations
+ */
+/**
+ * xlnx_ptp_adjfine - Fine adjustment of the frequency on the hardware clock
+ * @ptp: ptp clock structure
+ * @scaled_ppm: signed scaled parts per million for frequency adjustment.
+ * Return: 0 on success
+ * TX and RX port periods are reloaded with the adjusted value.
+ *
+ */
+static int xlnx_ptp_adjfine(struct ptp_clock_info *ptp, long scaled_ppm)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+					ptp_clock_info);
+	bool neg_adj = false;
+	u64 adj;
+
+	if (scaled_ppm < 0) {
+		neg_adj = true;
+		scaled_ppm = -scaled_ppm;
+	}
+
+	adj = mul_u64_u32_div(timer->incr, scaled_ppm, USEC_PER_SEC);
+	adj >>= PPM_FRACTION; /* remove fractions */
+	adj = neg_adj ? (timer->incr - adj) : (timer->incr + adj);
+
+	xlnx_port_period_write(timer, adj);
+
+	return 0;
+}
+
+/**
+ * xlnx_ptp_adjtime - Adjust the current time on the hardware clock
+ * @ptp: ptp clock structure
+ * @delta: signed time in ns to be adjusted.
+ * Return: 0 on success
+ * System, TX and RX ports are reloaded with the adjusted time.
+ *
+ */
+static int xlnx_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						ptp_clock_info);
+	struct timespec64 offset;
+	u64 sign = 0;
+	s64 cumulative_delta = timer->timeoffset;
+
+	spin_lock(&timer->reg_lock);
+
+	/* Fixed offset between system and port timer */
+	delta += timer->static_delay;
+	cumulative_delta += delta;
+	timer->timeoffset = cumulative_delta;
+	if (cumulative_delta < 0) {
+		sign = XPTPTIMER_TOD_OFFSET_NEG;
+		cumulative_delta = -cumulative_delta;
+	}
+	offset = ns_to_timespec64(cumulative_delta);
+	offset.tv_sec |= sign;
+
+	xlnx_port_offset_write(timer, (const struct timespec64 *)&offset);
+
+	spin_unlock(&timer->reg_lock);
+
+	return 0;
+}
+
+/**
+ * xlnx_ptp_gettime - Get the current time on the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec64 containing the current TX port timer time.
+ * Return: 0 on success
+ * Since TX and RX ports are initialized and adjusted simultaneously,
+ * they should be the same.
+ *
+ */
+static int xlnx_ptp_gettime(struct ptp_clock_info *ptp, struct timespec64 *ts)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						    ptp_clock_info);
+
+	spin_lock(&timer->reg_lock);
+	xlnx_tod_read(timer, ts);
+	spin_unlock(&timer->reg_lock);
+
+	return 0;
+}
+
+/**
+ * xlnx_ptp_settime - Set the current time on the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec64 containing the new time
+ * Return: 0 on success
+ *
+ * The hardware loads the entire new value when a load register is triggered.
+ */
+static int xlnx_ptp_settime(struct ptp_clock_info *ptp,
+			    const struct timespec64 *ts)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+					ptp_clock_info);
+
+	spin_lock(&timer->reg_lock);
+	xlnx_tod_load_write(timer, ts);
+	spin_unlock(&timer->reg_lock);
+
+	return 0;
+}
+
+static int xlnx_ptp_enable(struct ptp_clock_info *ptp,
+			   struct ptp_clock_request *rq, int on)
+{
+	return -EOPNOTSUPP;
+}
+
+static struct ptp_clock_info xlnx_ptp_clock_info = {
+	.owner		= THIS_MODULE,
+	.name		= "Xilinx Timer",
+	.max_adj	= 64000000,	/* Safe max adjutment for clock rate */
+	.n_ext_ts	= 0,
+	.adjfine	= xlnx_ptp_adjfine,
+	.adjtime	= xlnx_ptp_adjtime,
+	.gettime64	= xlnx_ptp_gettime,
+	.settime64	= xlnx_ptp_settime,
+	.enable		= xlnx_ptp_enable,
+};
+
+static int xlnx_ptp_timer_probe(struct platform_device *pdev)
+{
+	struct xlnx_ptp_timer *timer;
+	struct resource *r_mem;
+	int err = 0;
+	struct timespec64 ts, tsp;
+	u32 nsec, sech, secl;
+
+	if (of_device_is_compatible(pdev->dev.of_node, "xlnx,timer-syncer-1588-1.0")) {
+		dev_err(&pdev->dev, "This Beta version is no longer supported. Please upgrade to 2.0 IP version and use xlnx,timer-syncer-1588-2.0 compatible string\n");
+		return -EINVAL;
+	}
+
+	timer = devm_kzalloc(&pdev->dev, sizeof(*timer), GFP_KERNEL);
+	if (!timer)
+		return -ENOMEM;
+
+	timer->dev = &pdev->dev;
+
+	r_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	timer->baseaddr = devm_ioremap_resource(&pdev->dev, r_mem);
+	if (IS_ERR(timer->baseaddr)) {
+		err = PTR_ERR(timer->baseaddr);
+		return err;
+	}
+
+	spin_lock_init(&timer->reg_lock);
+
+	timer->ptp_clock_info = xlnx_ptp_clock_info;
+
+	timer->ptp_clock = ptp_clock_register(&timer->ptp_clock_info,
+					      &pdev->dev);
+	if (IS_ERR(timer->ptp_clock)) {
+		err = PTR_ERR(timer->ptp_clock);
+		dev_err(&pdev->dev, "Failed to register ptp clock\n");
+		return err;
+	}
+
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_CONFIG_OFFSET,
+		     XPTPTIMER_CFG_MAIN_TOD_EN | XPTPTIMER_CFG_ENABLE_PORT0);
+	/*
+	 * TODO: This clock rate should be derived from system design.
+	 * This is design specific - for ex. 250MHz port clock rate; period is
+	 * 10^9/250 is 4ns. Set port timer PERIOD BEFORE calling settime,
+	 * so that the initial LOAD triggers everything together.
+	 */
+	timer->incr = ((u64)XPTPTIMER_CLOCK_PERIOD << XPTPTIMER_PERIOD_SHIFT);
+	xlnx_tod_period_write(timer, timer->incr);
+	xlnx_port_period_write(timer, timer->incr);
+
+	/* Initialize current time */
+	ts = ns_to_timespec64(ktime_to_ns(ktime_get_real()));
+	xlnx_ptp_settime(&timer->ptp_clock_info, &ts);
+
+	/*
+	 * A static delay of 7-8 clock cycles is expected between system and
+	 * port timer which should be 28-32ns on this system with 250MHz clock.
+	 */
+	xlnx_ptp_iow(timer, XPTPTIMER_TOD_SNAPSHOT_OFFSET,
+		     XPTPTIMER_SNAPSHOT_MASK);
+	nsec = xlnx_ptp_ior(timer, XPTPTIMER_SYS_NS_OFFSET);
+	sech = xlnx_ptp_ior(timer, XPTPTIMER_SYS_SEC_1_OFFSET);
+	secl = xlnx_ptp_ior(timer, XPTPTIMER_SYS_SEC_0_OFFSET);
+	ts.tv_nsec = nsec;
+	ts.tv_sec = (((u64)sech << 32) | secl) & XPTPTIMER_MAX_SEC_MASK;
+
+	nsec = xlnx_ptp_ior(timer, XPTPTIMER_PORT_TX_NS_SNAP_OFFSET);
+	secl = xlnx_ptp_ior(timer, XPTPTIMER_PORT_TX_SEC_0_SNAP_OFFSET);
+	sech = xlnx_ptp_ior(timer, XPTPTIMER_PORT_TX_SEC_1_SNAP_OFFSET);
+	tsp.tv_nsec = nsec;
+	tsp.tv_sec = (((u64)sech << 32) | secl) & XPTPTIMER_MAX_SEC_MASK;
+
+	ts = timespec64_sub(ts, tsp);
+	timer->static_delay = timespec64_to_ns(&ts);
+	dev_dbg(&pdev->dev, "Static delay %d\n", timer->static_delay);
+
+	platform_set_drvdata(pdev, timer);
+
+	dev_info(&pdev->dev, "Xilinx PTP timer driver probed\n");
+
+	return 0;
+}
+
+static int xlnx_ptp_timer_remove(struct platform_device *pdev)
+{
+	struct xlnx_ptp_timer *timer = platform_get_drvdata(pdev);
+
+	ptp_clock_unregister(timer->ptp_clock);
+
+	return 0;
+}
+
+static const struct of_device_id timer_1588_of_match[] = {
+	{ .compatible = "xlnx,timer-syncer-1588-1.0", },
+	{ .compatible = "xlnx,timer-syncer-1588-2.0", },
+		{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, timer_1588_of_match);
+
+static struct platform_driver xlnx_ptp_timer_driver = {
+	.probe		= xlnx_ptp_timer_probe,
+	.remove		= xlnx_ptp_timer_remove,
+	.driver		= {
+		.name = "xlnx_ptp_timer",
+		.of_match_table = timer_1588_of_match,
+	},
+};
+
+module_platform_driver(xlnx_ptp_timer_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("PTP Timer Syncer driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/Kconfig
@@ -492,6 +492,17 @@
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-sifive.
 
+config PWM_CADENCE
+	tristate "Cadence PWM support"
+	depends on OF
+	depends on COMMON_CLK
+	help
+	  Generic PWM framework driver for cadence TTC IP found on
+	  Xilinx Zynq/ZynqMP/Versal SOCs. Each TTC device has 3 PWM
+	  channels. Output of 0th PWM channel of each TTC device can
+	  be routed to MIO or EMIO, and output of 1st and 2nd PWM
+	  channels can be routed only to EMIO.
+
 config PWM_SL28CPLD
 	tristate "Kontron sl28cpld PWM support"
 	depends on MFD_SL28CPLD || COMPILE_TEST
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/Makefile
@@ -45,6 +45,7 @@
 obj-$(CONFIG_PWM_ROCKCHIP)	+= pwm-rockchip.o
 obj-$(CONFIG_PWM_SAMSUNG)	+= pwm-samsung.o
 obj-$(CONFIG_PWM_SIFIVE)	+= pwm-sifive.o
+obj-$(CONFIG_PWM_CADENCE)	+= pwm-cadence.o
 obj-$(CONFIG_PWM_SL28CPLD)	+= pwm-sl28cpld.o
 obj-$(CONFIG_PWM_SPEAR)		+= pwm-spear.o
 obj-$(CONFIG_PWM_SPRD)		+= pwm-sprd.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-ab8500.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-ab8500.c
@@ -96,7 +96,7 @@
 	int err;
 
 	if (pdev->id < 1 || pdev->id > 31)
-		return dev_err_probe(&pdev->dev, EINVAL, "Invalid device id %d\n", pdev->id);
+		return dev_err_probe(&pdev->dev, -EINVAL, "Invalid device id %d\n", pdev->id);
 
 	/*
 	 * Nothing to be done in probe, this is required to get the
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-atmel-hlcdc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-atmel-hlcdc.c
@@ -38,11 +38,11 @@
 	return container_of(chip, struct atmel_hlcdc_pwm, chip);
 }
 
-static int atmel_hlcdc_pwm_apply(struct pwm_chip *c, struct pwm_device *pwm,
+static int atmel_hlcdc_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 				 const struct pwm_state *state)
 {
-	struct atmel_hlcdc_pwm *chip = to_atmel_hlcdc_pwm(c);
-	struct atmel_hlcdc *hlcdc = chip->hlcdc;
+	struct atmel_hlcdc_pwm *atmel = to_atmel_hlcdc_pwm(chip);
+	struct atmel_hlcdc *hlcdc = atmel->hlcdc;
 	unsigned int status;
 	int ret;
 
@@ -54,7 +54,7 @@
 		u32 pwmcfg;
 		int pres;
 
-		if (!chip->errata || !chip->errata->slow_clk_erratum) {
+		if (!atmel->errata || !atmel->errata->slow_clk_erratum) {
 			clk_freq = clk_get_rate(new_clk);
 			if (!clk_freq)
 				return -EINVAL;
@@ -64,7 +64,7 @@
 		}
 
 		/* Errata: cannot use slow clk on some IP revisions */
-		if ((chip->errata && chip->errata->slow_clk_erratum) ||
+		if ((atmel->errata && atmel->errata->slow_clk_erratum) ||
 		    clk_period_ns > state->period) {
 			new_clk = hlcdc->sys_clk;
 			clk_freq = clk_get_rate(new_clk);
@@ -77,8 +77,8 @@
 
 		for (pres = 0; pres <= ATMEL_HLCDC_PWMPS_MAX; pres++) {
 		/* Errata: cannot divide by 1 on some IP revisions */
-			if (!pres && chip->errata &&
-			    chip->errata->div1_clk_erratum)
+			if (!pres && atmel->errata &&
+			    atmel->errata->div1_clk_erratum)
 				continue;
 
 			if ((clk_period_ns << pres) >= state->period)
@@ -90,7 +90,7 @@
 
 		pwmcfg = ATMEL_HLCDC_PWMPS(pres);
 
-		if (new_clk != chip->cur_clk) {
+		if (new_clk != atmel->cur_clk) {
 			u32 gencfg = 0;
 			int ret;
 
@@ -98,8 +98,8 @@
 			if (ret)
 				return ret;
 
-			clk_disable_unprepare(chip->cur_clk);
-			chip->cur_clk = new_clk;
+			clk_disable_unprepare(atmel->cur_clk);
+			atmel->cur_clk = new_clk;
 
 			if (new_clk == hlcdc->sys_clk)
 				gencfg = ATMEL_HLCDC_CLKPWMSEL;
@@ -160,8 +160,8 @@
 		if (ret)
 			return ret;
 
-		clk_disable_unprepare(chip->cur_clk);
-		chip->cur_clk = NULL;
+		clk_disable_unprepare(atmel->cur_clk);
+		atmel->cur_clk = NULL;
 	}
 
 	return 0;
@@ -183,31 +183,32 @@
 #ifdef CONFIG_PM_SLEEP
 static int atmel_hlcdc_pwm_suspend(struct device *dev)
 {
-	struct atmel_hlcdc_pwm *chip = dev_get_drvdata(dev);
+	struct atmel_hlcdc_pwm *atmel = dev_get_drvdata(dev);
 
 	/* Keep the periph clock enabled if the PWM is still running. */
-	if (pwm_is_enabled(&chip->chip.pwms[0]))
-		clk_disable_unprepare(chip->hlcdc->periph_clk);
+	if (!pwm_is_enabled(&atmel->chip.pwms[0]))
+		clk_disable_unprepare(atmel->hlcdc->periph_clk);
 
 	return 0;
 }
 
 static int atmel_hlcdc_pwm_resume(struct device *dev)
 {
-	struct atmel_hlcdc_pwm *chip = dev_get_drvdata(dev);
+	struct atmel_hlcdc_pwm *atmel = dev_get_drvdata(dev);
 	struct pwm_state state;
 	int ret;
 
-	pwm_get_state(&chip->chip.pwms[0], &state);
+	pwm_get_state(&atmel->chip.pwms[0], &state);
 
 	/* Re-enable the periph clock it was stopped during suspend. */
 	if (!state.enabled) {
-		ret = clk_prepare_enable(chip->hlcdc->periph_clk);
+		ret = clk_prepare_enable(atmel->hlcdc->periph_clk);
 		if (ret)
 			return ret;
 	}
 
-	return atmel_hlcdc_pwm_apply(&chip->chip, &chip->chip.pwms[0], &state);
+	return atmel_hlcdc_pwm_apply(&atmel->chip, &atmel->chip.pwms[0],
+				     &state);
 }
 #endif
 
@@ -244,14 +245,14 @@
 {
 	const struct of_device_id *match;
 	struct device *dev = &pdev->dev;
-	struct atmel_hlcdc_pwm *chip;
+	struct atmel_hlcdc_pwm *atmel;
 	struct atmel_hlcdc *hlcdc;
 	int ret;
 
 	hlcdc = dev_get_drvdata(dev->parent);
 
-	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
-	if (!chip)
+	atmel = devm_kzalloc(dev, sizeof(*atmel), GFP_KERNEL);
+	if (!atmel)
 		return -ENOMEM;
 
 	ret = clk_prepare_enable(hlcdc->periph_clk);
@@ -260,33 +261,31 @@
 
 	match = of_match_node(atmel_hlcdc_dt_ids, dev->parent->of_node);
 	if (match)
-		chip->errata = match->data;
+		atmel->errata = match->data;
 
-	chip->hlcdc = hlcdc;
-	chip->chip.ops = &atmel_hlcdc_pwm_ops;
-	chip->chip.dev = dev;
-	chip->chip.npwm = 1;
+	atmel->hlcdc = hlcdc;
+	atmel->chip.ops = &atmel_hlcdc_pwm_ops;
+	atmel->chip.dev = dev;
+	atmel->chip.npwm = 1;
 
-	ret = pwmchip_add(&chip->chip);
+	ret = pwmchip_add(&atmel->chip);
 	if (ret) {
 		clk_disable_unprepare(hlcdc->periph_clk);
 		return ret;
 	}
 
-	platform_set_drvdata(pdev, chip);
+	platform_set_drvdata(pdev, atmel);
 
 	return 0;
 }
 
-static int atmel_hlcdc_pwm_remove(struct platform_device *pdev)
+static void atmel_hlcdc_pwm_remove(struct platform_device *pdev)
 {
-	struct atmel_hlcdc_pwm *chip = platform_get_drvdata(pdev);
+	struct atmel_hlcdc_pwm *atmel = platform_get_drvdata(pdev);
 
-	pwmchip_remove(&chip->chip);
+	pwmchip_remove(&atmel->chip);
 
-	clk_disable_unprepare(chip->hlcdc->periph_clk);
-
-	return 0;
+	clk_disable_unprepare(atmel->hlcdc->periph_clk);
 }
 
 static const struct of_device_id atmel_hlcdc_pwm_dt_ids[] = {
@@ -301,7 +300,7 @@
 		.pm = &atmel_hlcdc_pwm_pm_ops,
 	},
 	.probe = atmel_hlcdc_pwm_probe,
-	.remove = atmel_hlcdc_pwm_remove,
+	.remove_new = atmel_hlcdc_pwm_remove,
 };
 module_platform_driver(atmel_hlcdc_pwm_driver);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-atmel-tcb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-atmel-tcb.c
@@ -422,13 +422,14 @@
 	struct atmel_tcb_pwm_chip *tcbpwm;
 	const struct atmel_tcb_config *config;
 	struct device_node *np = pdev->dev.of_node;
-	struct regmap *regmap;
-	struct clk *clk, *gclk = NULL;
-	struct clk *slow_clk;
 	char clk_name[] = "t0_clk";
 	int err;
 	int channel;
 
+	tcbpwm = devm_kzalloc(&pdev->dev, sizeof(*tcbpwm), GFP_KERNEL);
+	if (tcbpwm == NULL)
+		return -ENOMEM;
+
 	err = of_property_read_u32(np, "reg", &channel);
 	if (err < 0) {
 		dev_err(&pdev->dev,
@@ -437,49 +438,43 @@
 		return err;
 	}
 
-	regmap = syscon_node_to_regmap(np->parent);
-	if (IS_ERR(regmap))
-		return PTR_ERR(regmap);
-
-	slow_clk = of_clk_get_by_name(np->parent, "slow_clk");
-	if (IS_ERR(slow_clk))
-		return PTR_ERR(slow_clk);
+	tcbpwm->regmap = syscon_node_to_regmap(np->parent);
+	if (IS_ERR(tcbpwm->regmap))
+		return PTR_ERR(tcbpwm->regmap);
+
+	tcbpwm->slow_clk = of_clk_get_by_name(np->parent, "slow_clk");
+	if (IS_ERR(tcbpwm->slow_clk))
+		return PTR_ERR(tcbpwm->slow_clk);
 
 	clk_name[1] += channel;
-	clk = of_clk_get_by_name(np->parent, clk_name);
-	if (IS_ERR(clk))
-		clk = of_clk_get_by_name(np->parent, "t0_clk");
-	if (IS_ERR(clk))
-		return PTR_ERR(clk);
+	tcbpwm->clk = of_clk_get_by_name(np->parent, clk_name);
+	if (IS_ERR(tcbpwm->clk))
+		tcbpwm->clk = of_clk_get_by_name(np->parent, "t0_clk");
+	if (IS_ERR(tcbpwm->clk)) {
+		err = PTR_ERR(tcbpwm->clk);
+		goto err_slow_clk;
+	}
 
 	match = of_match_node(atmel_tcb_of_match, np->parent);
 	config = match->data;
 
 	if (config->has_gclk) {
-		gclk = of_clk_get_by_name(np->parent, "gclk");
-		if (IS_ERR(gclk))
-			return PTR_ERR(gclk);
-	}
-
-	tcbpwm = devm_kzalloc(&pdev->dev, sizeof(*tcbpwm), GFP_KERNEL);
-	if (tcbpwm == NULL) {
-		err = -ENOMEM;
-		goto err_slow_clk;
+		tcbpwm->gclk = of_clk_get_by_name(np->parent, "gclk");
+		if (IS_ERR(tcbpwm->gclk)) {
+			err = PTR_ERR(tcbpwm->gclk);
+			goto err_clk;
+		}
 	}
 
 	tcbpwm->chip.dev = &pdev->dev;
 	tcbpwm->chip.ops = &atmel_tcb_pwm_ops;
 	tcbpwm->chip.npwm = NPWM;
 	tcbpwm->channel = channel;
-	tcbpwm->regmap = regmap;
-	tcbpwm->clk = clk;
-	tcbpwm->gclk = gclk;
-	tcbpwm->slow_clk = slow_clk;
 	tcbpwm->width = config->counter_width;
 
-	err = clk_prepare_enable(slow_clk);
+	err = clk_prepare_enable(tcbpwm->slow_clk);
 	if (err)
-		goto err_slow_clk;
+		goto err_gclk;
 
 	spin_lock_init(&tcbpwm->lock);
 
@@ -494,23 +489,28 @@
 err_disable_clk:
 	clk_disable_unprepare(tcbpwm->slow_clk);
 
+err_gclk:
+	clk_put(tcbpwm->gclk);
+
+err_clk:
+	clk_put(tcbpwm->clk);
+
 err_slow_clk:
-	clk_put(slow_clk);
+	clk_put(tcbpwm->slow_clk);
 
 	return err;
 }
 
-static int atmel_tcb_pwm_remove(struct platform_device *pdev)
+static void atmel_tcb_pwm_remove(struct platform_device *pdev)
 {
 	struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
 
 	pwmchip_remove(&tcbpwm->chip);
 
 	clk_disable_unprepare(tcbpwm->slow_clk);
-	clk_put(tcbpwm->slow_clk);
+	clk_put(tcbpwm->gclk);
 	clk_put(tcbpwm->clk);
-
-	return 0;
+	clk_put(tcbpwm->slow_clk);
 }
 
 static const struct of_device_id atmel_tcb_pwm_dt_ids[] = {
@@ -564,7 +564,7 @@
 		.pm = &atmel_tcb_pwm_pm_ops,
 	},
 	.probe = atmel_tcb_pwm_probe,
-	.remove = atmel_tcb_pwm_remove,
+	.remove_new = atmel_tcb_pwm_remove,
 };
 module_platform_driver(atmel_tcb_pwm_driver);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-brcmstb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-brcmstb.c
@@ -294,7 +294,7 @@
 {
 	struct brcmstb_pwm *p = dev_get_drvdata(dev);
 
-	clk_disable(p->clk);
+	clk_disable_unprepare(p->clk);
 
 	return 0;
 }
@@ -303,7 +303,7 @@
 {
 	struct brcmstb_pwm *p = dev_get_drvdata(dev);
 
-	clk_enable(p->clk);
+	clk_prepare_enable(p->clk);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-cadence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-cadence.c
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver to configure cadence TTC timer as PWM
+ * generator
+ *
+ * Copyright (c) 2021 Xilinx, Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/of_address.h>
+
+#define TTC_CLK_CNTRL_OFFSET		0x00
+#define TTC_CNT_CNTRL_OFFSET		0x0C
+#define TTC_MATCH_CNT_VAL_OFFSET	0x30
+#define TTC_COUNT_VAL_OFFSET		0x18
+#define TTC_INTR_VAL_OFFSET		0x24
+#define TTC_ISR_OFFSET			0x54
+#define TTC_IER_OFFSET			0x60
+#define TTC_PWM_CHANNEL_OFFSET		0x4
+
+#define TTC_CLK_CNTRL_CSRC_MASK		BIT(5)
+#define TTC_CLK_CNTRL_PSV_MASK		GENMASK(4, 1)
+
+#define TTC_CNTR_CTRL_DIS_MASK		BIT(0)
+#define TTC_CNTR_CTRL_INTR_MODE_EN_MASK	BIT(1)
+#define TTC_CNTR_CTRL_MATCH_MODE_EN_MASK	BIT(3)
+#define TTC_CNTR_CTRL_RST_MASK		BIT(4)
+#define TTC_CNTR_CTRL_WAVE_EN_MASK	BIT(5)
+#define TTC_CNTR_CTRL_WAVE_POL_MASK	BIT(6)
+
+#define TTC_CLK_CNTRL_PSV_SHIFT		1
+
+#define TTC_PWM_MAX_CH			3
+
+/**
+ * struct ttc_pwm_priv - Private data for TTC PWM drivers
+ * @chip:	PWM chip structure representing PWM controller
+ * @clk:	TTC input clock
+ * @max:	Maximum value of the counters
+ * @base:	Base address of TTC instance
+ */
+struct ttc_pwm_priv {
+	struct pwm_chip chip;
+	struct clk *clk;
+	u32 max;
+	void __iomem *base;
+};
+
+static inline u32 ttc_pwm_readl(struct ttc_pwm_priv *priv,
+				unsigned long offset)
+{
+	return readl_relaxed(priv->base + offset);
+}
+
+static inline void ttc_pwm_writel(struct ttc_pwm_priv *priv,
+				  unsigned long offset,
+				  unsigned long val)
+{
+	writel_relaxed(val, priv->base + offset);
+}
+
+static inline u32 ttc_pwm_ch_readl(struct ttc_pwm_priv *priv,
+				   struct pwm_device *pwm,
+				   unsigned long offset)
+{
+	unsigned long pwm_ch_offset = offset +
+				       (TTC_PWM_CHANNEL_OFFSET * pwm->hwpwm);
+
+	return ttc_pwm_readl(priv, pwm_ch_offset);
+}
+
+static inline void ttc_pwm_ch_writel(struct ttc_pwm_priv *priv,
+				     struct pwm_device *pwm,
+				     unsigned long offset,
+				     unsigned long val)
+{
+	unsigned long pwm_ch_offset = offset +
+				       (TTC_PWM_CHANNEL_OFFSET * pwm->hwpwm);
+
+	ttc_pwm_writel(priv, pwm_ch_offset, val);
+}
+
+static inline struct ttc_pwm_priv *xilinx_pwm_chip_to_priv(struct pwm_chip *chip)
+{
+	return container_of(chip, struct ttc_pwm_priv, chip);
+}
+
+static void ttc_pwm_enable(struct ttc_pwm_priv *priv, struct pwm_device *pwm)
+{
+	u32 ctrl_reg;
+
+	ctrl_reg = ttc_pwm_ch_readl(priv, pwm, TTC_CNT_CNTRL_OFFSET);
+	ctrl_reg |= (TTC_CNTR_CTRL_INTR_MODE_EN_MASK
+				 | TTC_CNTR_CTRL_MATCH_MODE_EN_MASK | TTC_CNTR_CTRL_RST_MASK);
+	ctrl_reg &= (~(TTC_CNTR_CTRL_DIS_MASK | TTC_CNTR_CTRL_WAVE_EN_MASK));
+	ttc_pwm_ch_writel(priv, pwm, TTC_CNT_CNTRL_OFFSET, ctrl_reg);
+}
+
+static void ttc_pwm_disable(struct ttc_pwm_priv *priv, struct pwm_device *pwm)
+{
+	u32 ctrl_reg;
+
+	ctrl_reg = ttc_pwm_ch_readl(priv, pwm, TTC_CNT_CNTRL_OFFSET);
+	ctrl_reg |= TTC_CNTR_CTRL_DIS_MASK;
+
+	ttc_pwm_ch_writel(priv, pwm, TTC_CNT_CNTRL_OFFSET, ctrl_reg);
+}
+
+static void ttc_pwm_rev_polarity(struct ttc_pwm_priv *priv, struct pwm_device *pwm)
+{
+	u32 ctrl_reg;
+
+	ctrl_reg = ttc_pwm_ch_readl(priv, pwm, TTC_CNT_CNTRL_OFFSET);
+	ctrl_reg ^= TTC_CNTR_CTRL_WAVE_POL_MASK;
+	ttc_pwm_ch_writel(priv, pwm, TTC_CNT_CNTRL_OFFSET, ctrl_reg);
+}
+
+static void ttc_pwm_set_counters(struct ttc_pwm_priv *priv,
+				 struct pwm_device *pwm,
+				 u32 div,
+				 u32 period_cycles,
+				 u32 duty_cycles)
+{
+	u32 clk_reg;
+
+	/* Set up prescalar */
+	clk_reg = ttc_pwm_ch_readl(priv, pwm, TTC_CLK_CNTRL_OFFSET);
+	clk_reg &= ~TTC_CLK_CNTRL_PSV_MASK;
+	clk_reg |= div;
+	ttc_pwm_ch_writel(priv, pwm, TTC_CLK_CNTRL_OFFSET, clk_reg);
+
+	/* Set up period */
+	ttc_pwm_ch_writel(priv, pwm, TTC_INTR_VAL_OFFSET, period_cycles);
+
+	/* Set up duty cycle */
+	ttc_pwm_ch_writel(priv, pwm, TTC_MATCH_CNT_VAL_OFFSET, duty_cycles);
+}
+
+static int ttc_pwm_apply(struct pwm_chip *chip,
+			 struct pwm_device *pwm,
+			 const struct pwm_state *state)
+{
+	u32 div = 0;
+	u64 period_cycles;
+	u64 duty_cycles;
+	unsigned long rate;
+	struct pwm_state cstate;
+	struct ttc_pwm_priv *priv = xilinx_pwm_chip_to_priv(chip);
+
+	pwm_get_state(pwm, &cstate);
+
+	if (state->polarity != cstate.polarity) {
+		if (cstate.enabled)
+			ttc_pwm_disable(priv, pwm);
+
+		ttc_pwm_rev_polarity(priv, pwm);
+
+		if (cstate.enabled)
+			ttc_pwm_enable(priv, pwm);
+	}
+
+	if (state->period != cstate.period ||
+	    state->duty_cycle != cstate.duty_cycle) {
+		rate = clk_get_rate(priv->clk);
+
+		/* Prevent overflow by limiting to the maximum possible period */
+		period_cycles = min_t(u64, state->period, ULONG_MAX * NSEC_PER_SEC);
+		period_cycles = mul_u64_u64_div_u64(period_cycles, rate, NSEC_PER_SEC);
+
+		if (period_cycles > priv->max) {
+			/* prescale frequency to fit requested period cycles within limit */
+			div = 1;
+
+			while ((period_cycles  > priv->max) && (div < 65536)) {
+				rate = DIV_ROUND_CLOSEST(rate, BIT(div));
+				period_cycles = mul_u64_u32_div(state->period,
+								rate, NSEC_PER_SEC);
+				if (period_cycles < priv->max)
+					break;
+				div++;
+			}
+
+			if (period_cycles  > priv->max)
+				return -ERANGE;
+		}
+
+		duty_cycles = mul_u64_u32_div(state->duty_cycle,
+					      rate, NSEC_PER_SEC);
+
+		if (cstate.enabled)
+			ttc_pwm_disable(priv, pwm);
+
+		ttc_pwm_set_counters(priv, pwm, div, period_cycles, duty_cycles);
+
+		if (cstate.enabled)
+			ttc_pwm_enable(priv, pwm);
+	}
+
+	if (state->enabled != cstate.enabled) {
+		if (state->enabled)
+			ttc_pwm_enable(priv, pwm);
+		else
+			ttc_pwm_disable(priv, pwm);
+	}
+
+	return 0;
+}
+
+static void ttc_pwm_get_state(struct pwm_chip *chip,
+			      struct pwm_device *pwm,
+			      struct pwm_state *state)
+{
+	struct ttc_pwm_priv *priv = xilinx_pwm_chip_to_priv(chip);
+	unsigned long rate;
+	u32 value;
+	u64 tmp;
+
+	value = ttc_pwm_ch_readl(priv, pwm, TTC_CNT_CNTRL_OFFSET);
+
+	if (value & TTC_CNTR_CTRL_WAVE_POL_MASK)
+		state->polarity = PWM_POLARITY_INVERSED;
+	else
+		state->polarity = PWM_POLARITY_NORMAL;
+
+	if (value & TTC_CNTR_CTRL_DIS_MASK)
+		state->enabled = false;
+	else
+		state->enabled = true;
+
+	rate = clk_get_rate(priv->clk);
+
+	tmp = ttc_pwm_ch_readl(priv, pwm, TTC_INTR_VAL_OFFSET);
+	state->period = DIV_ROUND_CLOSEST_ULL(tmp, rate);
+
+	tmp = ttc_pwm_ch_readl(priv, pwm, TTC_MATCH_CNT_VAL_OFFSET);
+	state->duty_cycle = DIV_ROUND_CLOSEST_ULL(tmp, rate);
+}
+
+static struct pwm_device *
+ttc_pwm_of_xlate(struct pwm_chip *chip, const struct of_phandle_args *args)
+{
+	struct pwm_device *pwm;
+
+	if (args->args[0] >= TTC_PWM_MAX_CH)
+		return NULL;
+
+	pwm = pwm_request_from_chip(chip, args->args[0], NULL);
+	if (IS_ERR(pwm))
+		return pwm;
+
+	if (args->args[1])
+		pwm->args.period = args->args[1];
+
+	if (args->args[2])
+		pwm->args.polarity = args->args[2];
+
+	return pwm;
+}
+
+static const struct pwm_ops ttc_pwm_ops = {
+	.apply = ttc_pwm_apply,
+	.get_state = ttc_pwm_get_state,
+	.owner = THIS_MODULE,
+};
+
+static int ttc_pwm_probe(struct platform_device *pdev)
+{
+	int ret;
+	int clksel;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct ttc_pwm_priv *priv;
+	u32 pwm_cells;
+	u32 timer_width;
+	struct clk *clk_cs;
+
+	ret = of_property_read_u32(np, "#pwm-cells", &pwm_cells);
+	if (ret == -EINVAL)
+		return -ENODEV;
+
+	if (ret)
+		return dev_err_probe(dev, ret, "could not read #pwm-cells\n");
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	ret = of_property_read_u32(np, "timer-width", &timer_width);
+	if (ret)
+		timer_width = 16;
+
+	priv->max = BIT(timer_width) - 1;
+
+	clksel = ttc_pwm_readl(priv, TTC_CLK_CNTRL_OFFSET);
+	clksel = !!(clksel & TTC_CLK_CNTRL_CSRC_MASK);
+	clk_cs = of_clk_get(np, clksel);
+	if (IS_ERR(clk_cs))
+		return dev_err_probe(dev, PTR_ERR(clk_cs),
+				     "ERROR: timer input clock not found\n");
+
+	priv->clk = clk_cs;
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return dev_err_probe(dev, ret, "Clock enable failed\n");
+
+	clk_rate_exclusive_get(priv->clk);
+
+	priv->chip.dev = dev;
+	priv->chip.ops = &ttc_pwm_ops;
+	priv->chip.npwm = TTC_PWM_MAX_CH;
+	priv->chip.of_xlate = ttc_pwm_of_xlate;
+	ret = pwmchip_add(&priv->chip);
+	if (ret) {
+		clk_rate_exclusive_put(priv->clk);
+		clk_disable_unprepare(priv->clk);
+		return dev_err_probe(dev, ret, "Could not register PWM chip\n");
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	return 0;
+}
+
+static int ttc_pwm_remove(struct platform_device *pdev)
+{
+	struct ttc_pwm_priv *priv = platform_get_drvdata(pdev);
+
+	pwmchip_remove(&priv->chip);
+	clk_rate_exclusive_put(priv->clk);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static const struct of_device_id ttc_pwm_of_match[] = {
+	{ .compatible = "cdns,ttc"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, ttc_pwm_of_match);
+
+static struct platform_driver ttc_pwm_driver = {
+	.probe = ttc_pwm_probe,
+	.remove = ttc_pwm_remove,
+	.driver = {
+		.name = "ttc-pwm",
+		.of_match_table = of_match_ptr(ttc_pwm_of_match),
+	},
+};
+module_platform_driver(ttc_pwm_driver);
+
+MODULE_AUTHOR("Mubin Usman Sayyed <mubin.usman.sayyed@xilinx.com>");
+MODULE_DESCRIPTION("Cadence TTC PWM driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-cros-ec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-cros-ec.c
@@ -157,6 +157,7 @@
 
 	state->enabled = (ret > 0);
 	state->period = EC_PWM_MAX_DUTY;
+	state->polarity = PWM_POLARITY_NORMAL;
 
 	/*
 	 * Note that "disabled" and "duty cycle == 0" are treated the same. If
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-hibvt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-hibvt.c
@@ -146,6 +146,7 @@
 
 	value = readl(base + PWM_CTRL_ADDR(pwm->hwpwm));
 	state->enabled = (PWM_ENABLE_MASK & value);
+	state->polarity = (PWM_POLARITY_MASK & value) ? PWM_POLARITY_INVERSED : PWM_POLARITY_NORMAL;
 }
 
 static int hibvt_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-imx-tpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-imx-tpm.c
@@ -106,7 +106,9 @@
 	p->prescale = prescale;
 
 	period_count = (clock_unit + ((1 << prescale) >> 1)) >> prescale;
-	p->mod = period_count;
+	if (period_count == 0)
+		return -EINVAL;
+	p->mod = period_count - 1;
 
 	/* calculate real period HW can support */
 	tmp = (u64)period_count << prescale;
@@ -397,6 +399,13 @@
 	if (tpm->enable_count > 0)
 		return -EBUSY;
 
+	/*
+	 * Force 'real_period' to be zero to force period update code
+	 * can be executed after system resume back, since suspend causes
+	 * the period related registers to become their reset values.
+	 */
+	tpm->real_period = 0;
+
 	clk_disable_unprepare(tpm->clk);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-imx27.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-imx27.c
@@ -26,6 +26,7 @@
 #define MX3_PWMSR			0x04    /* PWM Status Register */
 #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
 #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
 #define MX3_PWMCR_FWM			GENMASK(27, 26)
 #define MX3_PWMCR_STOPEN		BIT(25)
@@ -215,11 +216,13 @@
 static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 			   const struct pwm_state *state)
 {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, period_us, tmp;
 	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
 	struct pwm_state cstate;
 	unsigned long long c;
 	unsigned long long clkrate;
+	unsigned long flags;
+	int val;
 	int ret;
 	u32 cr;
 
@@ -262,7 +265,98 @@
 		pwm_imx27_sw_reset(chip);
 	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	val = readl(imx->mmio_base + MX3_PWMPR);
+	val = val >= MX3_PWMPR_MAX ? MX3_PWMPR_MAX : val;
+	cr = readl(imx->mmio_base + MX3_PWMCR);
+	tmp = NSEC_PER_SEC * (u64)(val + 2) * MX3_PWMCR_PRESCALER_GET(cr);
+	tmp = DIV_ROUND_UP_ULL(tmp, clkrate);
+	period_us = DIV_ROUND_UP_ULL(tmp, 1000);
+
+	/*
+	 * ERR051198:
+	 * PWM: PWM output may not function correctly if the FIFO is empty when
+	 * a new SAR value is programmed
+	 *
+	 * Description:
+	 * When the PWM FIFO is empty, a new value programmed to the PWM Sample
+	 * register (PWM_PWMSAR) will be directly applied even if the current
+	 * timer period has not expired.
+	 *
+	 * If the new SAMPLE value programmed in the PWM_PWMSAR register is
+	 * less than the previous value, and the PWM counter register
+	 * (PWM_PWMCNR) that contains the current COUNT value is greater than
+	 * the new programmed SAMPLE value, the current period will not flip
+	 * the level. This may result in an output pulse with a duty cycle of
+	 * 100%.
+	 *
+	 * Consider a change from
+	 *     ________
+	 *    /        \______/
+	 *    ^      *        ^
+	 * to
+	 *     ____
+	 *    /    \__________/
+	 *    ^               ^
+	 * At the time marked by *, the new write value will be directly applied
+	 * to SAR even the current period is not over if FIFO is empty.
+	 *
+	 *     ________        ____________________
+	 *    /        \______/                    \__________/
+	 *    ^               ^      *        ^               ^
+	 *    |<-- old SAR -->|               |<-- new SAR -->|
+	 *
+	 * That is the output is active for a whole period.
+	 *
+	 * Workaround:
+	 * Check new SAR less than old SAR and current counter is in errata
+	 * windows, write extra old SAR into FIFO and new SAR will effect at
+	 * next period.
+	 *
+	 * Sometime period is quite long, such as over 1 second. If add old SAR
+	 * into FIFO unconditional, new SAR have to wait for next period. It
+	 * may be too long.
+	 *
+	 * Turn off the interrupt to ensure that not IRQ and schedule happen
+	 * during above operations. If any irq and schedule happen, counter
+	 * in PWM will be out of data and take wrong action.
+	 *
+	 * Add a safety margin 1.5us because it needs some time to complete
+	 * IO write.
+	 *
+	 * Use writel_relaxed() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest PWM frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500kHz), this workaround
+	 * can solve this problem. No software workaround is available if PWM
+	 * period is shorter than IO write. Just try best to fill old data
+	 * into FIFO.
+	 */
+	c = clkrate * 1500;
+	do_div(c, NSEC_PER_SEC);
+
+	local_irq_save(flags);
+	val = FIELD_GET(MX3_PWMSR_FIFOAV, readl_relaxed(imx->mmio_base + MX3_PWMSR));
+
+	if (duty_cycles < imx->duty_cycle && (cr & MX3_PWMCR_EN)) {
+		if (period_us < 2) { /* 2us = 500 kHz */
+			/* Best effort attempt to fix up >500 kHz case */
+			udelay(3 * period_us);
+			writel_relaxed(imx->duty_cycle, imx->mmio_base + MX3_PWMSAR);
+			writel_relaxed(imx->duty_cycle, imx->mmio_base + MX3_PWMSAR);
+		} else if (val < MX3_PWMSR_FIFOAV_2WORDS) {
+			val = readl_relaxed(imx->mmio_base + MX3_PWMCNR);
+			/*
+			 * If counter is close to period, controller may roll over when
+			 * next IO write.
+			 */
+			if ((val + c >= duty_cycles && val < imx->duty_cycle) ||
+			    val + c >= period_cycles)
+				writel_relaxed(imx->duty_cycle, imx->mmio_base + MX3_PWMSAR);
+		}
+	}
+	writel_relaxed(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	local_irq_restore(flags);
+
 	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-iqs620a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-iqs620a.c
@@ -126,6 +126,7 @@
 	mutex_unlock(&iqs620_pwm->lock);
 
 	state->period = IQS620_PWM_PERIOD_NS;
+	state->polarity = PWM_POLARITY_NORMAL;
 }
 
 static int iqs620_pwm_notifier(struct notifier_block *notifier,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-jz4740.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-jz4740.c
@@ -60,9 +60,10 @@
 	snprintf(name, sizeof(name), "timer%u", pwm->hwpwm);
 
 	clk = clk_get(chip->dev, name);
-	if (IS_ERR(clk))
-		return dev_err_probe(chip->dev, PTR_ERR(clk),
-				     "Failed to get clock\n");
+	if (IS_ERR(clk)) {
+		dev_err(chip->dev, "error %pe: Failed to get clock\n", clk);
+		return PTR_ERR(clk);
+	}
 
 	err = clk_prepare_enable(clk);
 	if (err < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-lp3943.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-lp3943.c
@@ -125,6 +125,7 @@
 	if (err)
 		return err;
 
+	duty_ns = min(duty_ns, period_ns);
 	val = (u8)(duty_ns * LP3943_MAX_DUTY / period_ns);
 
 	return lp3943_write_byte(lp3943, reg_duty, val);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-lpc18xx-sct.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-lpc18xx-sct.c
@@ -76,6 +76,8 @@
 #define LPC18XX_PWM_EVENT_PERIOD	0
 #define LPC18XX_PWM_EVENT_MAX		16
 
+#define LPC18XX_NUM_PWMS		16
+
 /* SCT conflict resolution */
 enum lpc18xx_pwm_res_action {
 	LPC18XX_PWM_RES_NONE,
@@ -96,11 +98,12 @@
 	unsigned long clk_rate;
 	unsigned int period_ns;
 	unsigned int min_period_ns;
-	unsigned int max_period_ns;
+	u64 max_period_ns;
 	unsigned int period_event;
 	unsigned long event_map;
 	struct mutex res_lock;
 	struct mutex period_lock;
+	struct lpc18xx_pwm_data channeldata[LPC18XX_NUM_PWMS];
 };
 
 static inline struct lpc18xx_pwm_chip *
@@ -142,40 +145,48 @@
 	mutex_unlock(&lpc18xx_pwm->res_lock);
 }
 
-static void lpc18xx_pwm_config_period(struct pwm_chip *chip, int period_ns)
+static void lpc18xx_pwm_config_period(struct pwm_chip *chip, u64 period_ns)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm = to_lpc18xx_pwm_chip(chip);
-	u64 val;
+	u32 val;
 
-	val = (u64)period_ns * lpc18xx_pwm->clk_rate;
-	do_div(val, NSEC_PER_SEC);
+	/*
+	 * With clk_rate < NSEC_PER_SEC this cannot overflow.
+	 * With period_ns < max_period_ns this also fits into an u32.
+	 * As period_ns >= min_period_ns = DIV_ROUND_UP(NSEC_PER_SEC, lpc18xx_pwm->clk_rate);
+	 * we have val >= 1.
+	 */
+	val = mul_u64_u64_div_u64(period_ns, lpc18xx_pwm->clk_rate, NSEC_PER_SEC);
 
 	lpc18xx_pwm_writel(lpc18xx_pwm,
 			   LPC18XX_PWM_MATCH(lpc18xx_pwm->period_event),
-			   (u32)val - 1);
+			   val - 1);
 
 	lpc18xx_pwm_writel(lpc18xx_pwm,
 			   LPC18XX_PWM_MATCHREL(lpc18xx_pwm->period_event),
-			   (u32)val - 1);
+			   val - 1);
 }
 
 static void lpc18xx_pwm_config_duty(struct pwm_chip *chip,
-				    struct pwm_device *pwm, int duty_ns)
+				    struct pwm_device *pwm, u64 duty_ns)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm = to_lpc18xx_pwm_chip(chip);
-	struct lpc18xx_pwm_data *lpc18xx_data = pwm_get_chip_data(pwm);
-	u64 val;
+	struct lpc18xx_pwm_data *lpc18xx_data = &lpc18xx_pwm->channeldata[pwm->hwpwm];
+	u32 val;
 
-	val = (u64)duty_ns * lpc18xx_pwm->clk_rate;
-	do_div(val, NSEC_PER_SEC);
+	/*
+	 * With clk_rate < NSEC_PER_SEC this cannot overflow.
+	 * With duty_ns <= period_ns < max_period_ns this also fits into an u32.
+	 */
+	val = mul_u64_u64_div_u64(duty_ns, lpc18xx_pwm->clk_rate, NSEC_PER_SEC);
 
 	lpc18xx_pwm_writel(lpc18xx_pwm,
 			   LPC18XX_PWM_MATCH(lpc18xx_data->duty_event),
-			   (u32)val);
+			   val);
 
 	lpc18xx_pwm_writel(lpc18xx_pwm,
 			   LPC18XX_PWM_MATCHREL(lpc18xx_data->duty_event),
-			   (u32)val);
+			   val);
 }
 
 static int lpc18xx_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
@@ -233,7 +244,7 @@
 static int lpc18xx_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm = to_lpc18xx_pwm_chip(chip);
-	struct lpc18xx_pwm_data *lpc18xx_data = pwm_get_chip_data(pwm);
+	struct lpc18xx_pwm_data *lpc18xx_data = &lpc18xx_pwm->channeldata[pwm->hwpwm];
 	enum lpc18xx_pwm_res_action res_action;
 	unsigned int set_event, clear_event;
 
@@ -268,7 +279,7 @@
 static void lpc18xx_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm = to_lpc18xx_pwm_chip(chip);
-	struct lpc18xx_pwm_data *lpc18xx_data = pwm_get_chip_data(pwm);
+	struct lpc18xx_pwm_data *lpc18xx_data = &lpc18xx_pwm->channeldata[pwm->hwpwm];
 
 	lpc18xx_pwm_writel(lpc18xx_pwm,
 			   LPC18XX_PWM_EVCTRL(lpc18xx_data->duty_event), 0);
@@ -279,7 +290,7 @@
 static int lpc18xx_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm = to_lpc18xx_pwm_chip(chip);
-	struct lpc18xx_pwm_data *lpc18xx_data = pwm_get_chip_data(pwm);
+	struct lpc18xx_pwm_data *lpc18xx_data = &lpc18xx_pwm->channeldata[pwm->hwpwm];
 	unsigned long event;
 
 	event = find_first_zero_bit(&lpc18xx_pwm->event_map,
@@ -300,7 +311,7 @@
 static void lpc18xx_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm = to_lpc18xx_pwm_chip(chip);
-	struct lpc18xx_pwm_data *lpc18xx_data = pwm_get_chip_data(pwm);
+	struct lpc18xx_pwm_data *lpc18xx_data = &lpc18xx_pwm->channeldata[pwm->hwpwm];
 
 	clear_bit(lpc18xx_data->duty_event, &lpc18xx_pwm->event_map);
 }
@@ -324,8 +335,7 @@
 static int lpc18xx_pwm_probe(struct platform_device *pdev)
 {
 	struct lpc18xx_pwm_chip *lpc18xx_pwm;
-	struct pwm_device *pwm;
-	int ret, i;
+	int ret;
 	u64 val;
 
 	lpc18xx_pwm = devm_kzalloc(&pdev->dev, sizeof(*lpc18xx_pwm),
@@ -358,19 +368,34 @@
 		goto disable_pwmclk;
 	}
 
+	/*
+	 * If clkrate is too fast, the calculations in .apply() might overflow.
+	 */
+	if (lpc18xx_pwm->clk_rate > NSEC_PER_SEC) {
+		ret = dev_err_probe(&pdev->dev, -EINVAL, "pwm clock to fast\n");
+		goto disable_pwmclk;
+	}
+
+	/*
+	 * If clkrate is too fast, the calculations in .apply() might overflow.
+	 */
+	if (lpc18xx_pwm->clk_rate > NSEC_PER_SEC) {
+		ret = dev_err_probe(&pdev->dev, -EINVAL, "pwm clock to fast\n");
+		goto disable_pwmclk;
+	}
+
 	mutex_init(&lpc18xx_pwm->res_lock);
 	mutex_init(&lpc18xx_pwm->period_lock);
 
-	val = (u64)NSEC_PER_SEC * LPC18XX_PWM_TIMER_MAX;
-	do_div(val, lpc18xx_pwm->clk_rate);
-	lpc18xx_pwm->max_period_ns = val;
+	lpc18xx_pwm->max_period_ns =
+		mul_u64_u64_div_u64(NSEC_PER_SEC, LPC18XX_PWM_TIMER_MAX, lpc18xx_pwm->clk_rate);
 
 	lpc18xx_pwm->min_period_ns = DIV_ROUND_UP(NSEC_PER_SEC,
 						  lpc18xx_pwm->clk_rate);
 
 	lpc18xx_pwm->chip.dev = &pdev->dev;
 	lpc18xx_pwm->chip.ops = &lpc18xx_pwm_ops;
-	lpc18xx_pwm->chip.npwm = 16;
+	lpc18xx_pwm->chip.npwm = LPC18XX_NUM_PWMS;
 
 	/* SCT counter must be in unify (32 bit) mode */
 	lpc18xx_pwm_writel(lpc18xx_pwm, LPC18XX_PWM_CONFIG,
@@ -395,40 +420,23 @@
 	lpc18xx_pwm_writel(lpc18xx_pwm, LPC18XX_PWM_LIMIT,
 			   BIT(lpc18xx_pwm->period_event));
 
+	val = lpc18xx_pwm_readl(lpc18xx_pwm, LPC18XX_PWM_CTRL);
+	val &= ~LPC18XX_PWM_BIDIR;
+	val &= ~LPC18XX_PWM_CTRL_HALT;
+	val &= ~LPC18XX_PWM_PRE_MASK;
+	val |= LPC18XX_PWM_PRE(0);
+	lpc18xx_pwm_writel(lpc18xx_pwm, LPC18XX_PWM_CTRL, val);
+
 	ret = pwmchip_add(&lpc18xx_pwm->chip);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "pwmchip_add failed: %d\n", ret);
 		goto disable_pwmclk;
 	}
 
-	for (i = 0; i < lpc18xx_pwm->chip.npwm; i++) {
-		struct lpc18xx_pwm_data *data;
-
-		pwm = &lpc18xx_pwm->chip.pwms[i];
-
-		data = devm_kzalloc(lpc18xx_pwm->dev, sizeof(*data),
-				    GFP_KERNEL);
-		if (!data) {
-			ret = -ENOMEM;
-			goto remove_pwmchip;
-		}
-
-		pwm_set_chip_data(pwm, data);
-	}
-
 	platform_set_drvdata(pdev, lpc18xx_pwm);
 
-	val = lpc18xx_pwm_readl(lpc18xx_pwm, LPC18XX_PWM_CTRL);
-	val &= ~LPC18XX_PWM_BIDIR;
-	val &= ~LPC18XX_PWM_CTRL_HALT;
-	val &= ~LPC18XX_PWM_PRE_MASK;
-	val |= LPC18XX_PWM_PRE(0);
-	lpc18xx_pwm_writel(lpc18xx_pwm, LPC18XX_PWM_CTRL, val);
-
 	return 0;
 
-remove_pwmchip:
-	pwmchip_remove(&lpc18xx_pwm->chip);
 disable_pwmclk:
 	clk_disable_unprepare(lpc18xx_pwm->pwm_clk);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-lpc32xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-lpc32xx.c
@@ -51,10 +51,10 @@
 	if (duty_cycles > 255)
 		duty_cycles = 255;
 
-	val = readl(lpc32xx->base + (pwm->hwpwm << 2));
+	val = readl(lpc32xx->base);
 	val &= ~0xFFFF;
 	val |= (period_cycles << 8) | duty_cycles;
-	writel(val, lpc32xx->base + (pwm->hwpwm << 2));
+	writel(val, lpc32xx->base);
 
 	return 0;
 }
@@ -69,9 +69,9 @@
 	if (ret)
 		return ret;
 
-	val = readl(lpc32xx->base + (pwm->hwpwm << 2));
+	val = readl(lpc32xx->base);
 	val |= PWM_ENABLE;
-	writel(val, lpc32xx->base + (pwm->hwpwm << 2));
+	writel(val, lpc32xx->base);
 
 	return 0;
 }
@@ -81,9 +81,9 @@
 	struct lpc32xx_pwm_chip *lpc32xx = to_lpc32xx_pwm_chip(chip);
 	u32 val;
 
-	val = readl(lpc32xx->base + (pwm->hwpwm << 2));
+	val = readl(lpc32xx->base);
 	val &= ~PWM_ENABLE;
-	writel(val, lpc32xx->base + (pwm->hwpwm << 2));
+	writel(val, lpc32xx->base);
 
 	clk_disable_unprepare(lpc32xx->clk);
 }
@@ -118,9 +118,9 @@
 	lpc32xx->chip.npwm = 1;
 
 	/* If PWM is disabled, configure the output to the default value */
-	val = readl(lpc32xx->base + (lpc32xx->chip.pwms[0].hwpwm << 2));
+	val = readl(lpc32xx->base);
 	val &= ~PWM_PIN_LEVEL;
-	writel(val, lpc32xx->base + (lpc32xx->chip.pwms[0].hwpwm << 2));
+	writel(val, lpc32xx->base);
 
 	ret = devm_pwmchip_add(&pdev->dev, &lpc32xx->chip);
 	if (ret < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-mediatek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-mediatek.c
@@ -275,7 +275,7 @@
 static const struct pwm_mediatek_of_data mt7622_pwm_data = {
 	.num_pwms = 6,
 	.pwm45_fixup = false,
-	.has_ck_26m_sel = false,
+	.has_ck_26m_sel = true,
 };
 
 static const struct pwm_mediatek_of_data mt7623_pwm_data = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-meson.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-meson.c
@@ -147,12 +147,13 @@
 		return err;
 	}
 
-	return pwm_set_chip_data(pwm, channel);
+	return 0;
 }
 
 static void meson_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
 {
-	struct meson_pwm_channel *channel = pwm_get_chip_data(pwm);
+	struct meson_pwm *meson = to_meson_pwm(chip);
+	struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
 
 	if (channel)
 		clk_disable_unprepare(channel->clk);
@@ -161,13 +162,20 @@
 static int meson_pwm_calc(struct meson_pwm *meson, struct pwm_device *pwm,
 			  const struct pwm_state *state)
 {
-	struct meson_pwm_channel *channel = pwm_get_chip_data(pwm);
-	unsigned int duty, period, pre_div, cnt, duty_cnt;
+	struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
+	unsigned int pre_div, cnt, duty_cnt;
 	unsigned long fin_freq;
+	u64 duty, period;
 
 	duty = state->duty_cycle;
 	period = state->period;
 
+	/*
+	 * Note this is wrong. The result is an output wave that isn't really
+	 * inverted and so is wrongly identified by .get_state as normal.
+	 * Fixing this needs some care however as some machines might rely on
+	 * this.
+	 */
 	if (state->polarity == PWM_POLARITY_INVERSED)
 		duty = period - duty;
 
@@ -179,19 +187,19 @@
 
 	dev_dbg(meson->chip.dev, "fin_freq: %lu Hz\n", fin_freq);
 
-	pre_div = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * 0xffffLL);
+	pre_div = div64_u64(fin_freq * period, NSEC_PER_SEC * 0xffffLL);
 	if (pre_div > MISC_CLK_DIV_MASK) {
 		dev_err(meson->chip.dev, "unable to get period pre_div\n");
 		return -EINVAL;
 	}
 
-	cnt = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * (pre_div + 1));
+	cnt = div64_u64(fin_freq * period, NSEC_PER_SEC * (pre_div + 1));
 	if (cnt > 0xffff) {
 		dev_err(meson->chip.dev, "unable to get period cnt\n");
 		return -EINVAL;
 	}
 
-	dev_dbg(meson->chip.dev, "period=%u pre_div=%u cnt=%u\n", period,
+	dev_dbg(meson->chip.dev, "period=%llu pre_div=%u cnt=%u\n", period,
 		pre_div, cnt);
 
 	if (duty == period) {
@@ -204,14 +212,13 @@
 		channel->lo = cnt;
 	} else {
 		/* Then check is we can have the duty with the same pre_div */
-		duty_cnt = div64_u64(fin_freq * (u64)duty,
-				     NSEC_PER_SEC * (pre_div + 1));
+		duty_cnt = div64_u64(fin_freq * duty, NSEC_PER_SEC * (pre_div + 1));
 		if (duty_cnt > 0xffff) {
 			dev_err(meson->chip.dev, "unable to get duty cycle\n");
 			return -EINVAL;
 		}
 
-		dev_dbg(meson->chip.dev, "duty=%u pre_div=%u duty_cnt=%u\n",
+		dev_dbg(meson->chip.dev, "duty=%llu pre_div=%u duty_cnt=%u\n",
 			duty, pre_div, duty_cnt);
 
 		channel->pre_div = pre_div;
@@ -224,7 +231,7 @@
 
 static void meson_pwm_enable(struct meson_pwm *meson, struct pwm_device *pwm)
 {
-	struct meson_pwm_channel *channel = pwm_get_chip_data(pwm);
+	struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
 	struct meson_pwm_channel_data *channel_data;
 	unsigned long flags;
 	u32 value;
@@ -267,8 +274,8 @@
 static int meson_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 			   const struct pwm_state *state)
 {
-	struct meson_pwm_channel *channel = pwm_get_chip_data(pwm);
 	struct meson_pwm *meson = to_meson_pwm(chip);
+	struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
 	int err = 0;
 
 	if (!state)
@@ -366,6 +373,7 @@
 		state->period = 0;
 		state->duty_cycle = 0;
 	}
+	state->polarity = PWM_POLARITY_NORMAL;
 }
 
 static const struct pwm_ops meson_pwm_ops = {
@@ -417,7 +425,7 @@
 };
 
 static const char * const pwm_axg_ao_parent_names[] = {
-	"aoclk81", "xtal", "fclk_div4", "fclk_div5"
+	"xtal", "axg_ao_clk81", "fclk_div4", "fclk_div5"
 };
 
 static const struct meson_pwm_data pwm_axg_ao_data = {
@@ -426,7 +434,7 @@
 };
 
 static const char * const pwm_g12a_ao_ab_parent_names[] = {
-	"xtal", "aoclk81", "fclk_div4", "fclk_div5"
+	"xtal", "g12a_ao_clk81", "fclk_div4", "fclk_div5"
 };
 
 static const struct meson_pwm_data pwm_g12a_ao_ab_data = {
@@ -435,7 +443,7 @@
 };
 
 static const char * const pwm_g12a_ao_cd_parent_names[] = {
-	"xtal", "aoclk81",
+	"xtal", "g12a_ao_clk81",
 };
 
 static const struct meson_pwm_data pwm_g12a_ao_cd_data = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-mtk-disp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-mtk-disp.c
@@ -79,14 +79,11 @@
 	if (state->polarity != PWM_POLARITY_NORMAL)
 		return -EINVAL;
 
-	if (!state->enabled) {
-		mtk_disp_pwm_update_bits(mdp, DISP_PWM_EN, mdp->data->enable_mask,
-					 0x0);
-
-		if (mdp->enabled) {
-			clk_disable_unprepare(mdp->clk_mm);
-			clk_disable_unprepare(mdp->clk_main);
-		}
+	if (!state->enabled && mdp->enabled) {
+		mtk_disp_pwm_update_bits(mdp, DISP_PWM_EN,
+					 mdp->data->enable_mask, 0x0);
+		clk_disable_unprepare(mdp->clk_mm);
+		clk_disable_unprepare(mdp->clk_main);
 
 		mdp->enabled = false;
 		return 0;
@@ -138,6 +135,19 @@
 	high_width = mul_u64_u64_div_u64(state->duty_cycle, rate, div);
 	value = period | (high_width << PWM_HIGH_WIDTH_SHIFT);
 
+	if (mdp->data->bls_debug && !mdp->data->has_commit) {
+		/*
+		 * For MT2701, disable double buffer before writing register
+		 * and select manual mode and use PWM_PERIOD/PWM_HIGH_WIDTH.
+		 */
+		mtk_disp_pwm_update_bits(mdp, mdp->data->bls_debug,
+					 mdp->data->bls_debug_mask,
+					 mdp->data->bls_debug_mask);
+		mtk_disp_pwm_update_bits(mdp, mdp->data->con0,
+					 mdp->data->con0_sel,
+					 mdp->data->con0_sel);
+	}
+
 	mtk_disp_pwm_update_bits(mdp, mdp->data->con0,
 				 PWM_CLKDIV_MASK,
 				 clk_div << PWM_CLKDIV_SHIFT);
@@ -152,17 +162,6 @@
 		mtk_disp_pwm_update_bits(mdp, mdp->data->commit,
 					 mdp->data->commit_mask,
 					 0x0);
-	} else {
-		/*
-		 * For MT2701, disable double buffer before writing register
-		 * and select manual mode and use PWM_PERIOD/PWM_HIGH_WIDTH.
-		 */
-		mtk_disp_pwm_update_bits(mdp, mdp->data->bls_debug,
-					 mdp->data->bls_debug_mask,
-					 mdp->data->bls_debug_mask);
-		mtk_disp_pwm_update_bits(mdp, mdp->data->con0,
-					 mdp->data->con0_sel,
-					 mdp->data->con0_sel);
 	}
 
 	mtk_disp_pwm_update_bits(mdp, DISP_PWM_EN, mdp->data->enable_mask,
@@ -178,7 +177,7 @@
 {
 	struct mtk_disp_pwm *mdp = to_mtk_disp_pwm(chip);
 	u64 rate, period, high_width;
-	u32 clk_div, con0, con1;
+	u32 clk_div, pwm_en, con0, con1;
 	int err;
 
 	err = clk_prepare_enable(mdp->clk_main);
@@ -194,10 +193,21 @@
 		return;
 	}
 
+	/*
+	 * Apply DISP_PWM_DEBUG settings to choose whether to enable or disable
+	 * registers double buffer and manual commit to working register before
+	 * performing any read/write operation
+	 */
+	if (mdp->data->bls_debug)
+		mtk_disp_pwm_update_bits(mdp, mdp->data->bls_debug,
+					 mdp->data->bls_debug_mask,
+					 mdp->data->bls_debug_mask);
+
 	rate = clk_get_rate(mdp->clk_main);
 	con0 = readl(mdp->base + mdp->data->con0);
 	con1 = readl(mdp->base + mdp->data->con1);
-	state->enabled = !!(con0 & BIT(0));
+	pwm_en = readl(mdp->base + DISP_PWM_EN);
+	state->enabled = !!(pwm_en & mdp->data->enable_mask);
 	clk_div = FIELD_GET(PWM_CLKDIV_MASK, con0);
 	period = FIELD_GET(PWM_PERIOD_MASK, con1);
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-raspberrypi-poe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-raspberrypi-poe.c
@@ -66,7 +66,7 @@
 					u32 reg, u32 *val)
 {
 	struct raspberrypi_pwm_prop msg = {
-		.reg = reg
+		.reg = cpu_to_le32(reg),
 	};
 	int ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-sifive.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-sifive.c
@@ -23,7 +23,7 @@
 #define PWM_SIFIVE_PWMCFG		0x0
 #define PWM_SIFIVE_PWMCOUNT		0x8
 #define PWM_SIFIVE_PWMS			0x10
-#define PWM_SIFIVE_PWMCMP0		0x20
+#define PWM_SIFIVE_PWMCMP(i)		(0x20 + 4 * (i))
 
 /* PWMCFG fields */
 #define PWM_SIFIVE_PWMCFG_SCALE		GENMASK(3, 0)
@@ -36,14 +36,12 @@
 #define PWM_SIFIVE_PWMCFG_GANG		BIT(24)
 #define PWM_SIFIVE_PWMCFG_IP		BIT(28)
 
-/* PWM_SIFIVE_SIZE_PWMCMP is used to calculate offset for pwmcmpX registers */
-#define PWM_SIFIVE_SIZE_PWMCMP		4
 #define PWM_SIFIVE_CMPWIDTH		16
 #define PWM_SIFIVE_DEFAULT_PERIOD	10000000
 
 struct pwm_sifive_ddata {
 	struct pwm_chip	chip;
-	struct mutex lock; /* lock to protect user_count */
+	struct mutex lock; /* lock to protect user_count and approx_period */
 	struct notifier_block notifier;
 	struct clk *clk;
 	void __iomem *regs;
@@ -78,6 +76,7 @@
 	mutex_unlock(&ddata->lock);
 }
 
+/* Called holding ddata->lock */
 static void pwm_sifive_update_clock(struct pwm_sifive_ddata *ddata,
 				    unsigned long rate)
 {
@@ -112,8 +111,7 @@
 	struct pwm_sifive_ddata *ddata = pwm_sifive_chip_to_ddata(chip);
 	u32 duty, val;
 
-	duty = readl(ddata->regs + PWM_SIFIVE_PWMCMP0 +
-		     pwm->hwpwm * PWM_SIFIVE_SIZE_PWMCMP);
+	duty = readl(ddata->regs + PWM_SIFIVE_PWMCMP(pwm->hwpwm));
 
 	state->enabled = duty > 0;
 
@@ -166,7 +164,6 @@
 		return ret;
 	}
 
-	mutex_lock(&ddata->lock);
 	cur_state = pwm->state;
 	enabled = cur_state.enabled;
 
@@ -185,24 +182,31 @@
 	/* The hardware cannot generate a 100% duty cycle */
 	frac = min(frac, (1U << PWM_SIFIVE_CMPWIDTH) - 1);
 
+	mutex_lock(&ddata->lock);
 	if (state->period != ddata->approx_period) {
-		if (ddata->user_count != 1) {
+		/*
+		 * Don't let a 2nd user change the period underneath the 1st user.
+		 * However if ddate->approx_period == 0 this is the first time we set
+		 * any period, so let whoever gets here first set the period so other
+		 * users who agree on the period won't fail.
+		 */
+		if (ddata->user_count != 1 && ddata->approx_period) {
+			mutex_unlock(&ddata->lock);
 			ret = -EBUSY;
 			goto exit;
 		}
 		ddata->approx_period = state->period;
 		pwm_sifive_update_clock(ddata, clk_get_rate(ddata->clk));
 	}
+	mutex_unlock(&ddata->lock);
 
-	writel(frac, ddata->regs + PWM_SIFIVE_PWMCMP0 +
-	       pwm->hwpwm * PWM_SIFIVE_SIZE_PWMCMP);
+	writel(frac, ddata->regs + PWM_SIFIVE_PWMCMP(pwm->hwpwm));
 
 	if (state->enabled != enabled)
 		pwm_sifive_enable(chip, state->enabled);
 
 exit:
 	clk_disable(ddata->clk);
-	mutex_unlock(&ddata->lock);
 	return ret;
 }
 
@@ -221,8 +225,11 @@
 	struct pwm_sifive_ddata *ddata =
 		container_of(nb, struct pwm_sifive_ddata, notifier);
 
-	if (event == POST_RATE_CHANGE)
+	if (event == POST_RATE_CHANGE) {
+		mutex_lock(&ddata->lock);
 		pwm_sifive_update_clock(ddata, ndata->new_rate);
+		mutex_unlock(&ddata->lock);
+	}
 
 	return NOTIFY_OK;
 }
@@ -233,6 +240,8 @@
 	struct pwm_sifive_ddata *ddata;
 	struct pwm_chip *chip;
 	int ret;
+	u32 val;
+	unsigned int enabled_pwms = 0, enabled_clks = 1;
 
 	ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
 	if (!ddata)
@@ -259,6 +268,33 @@
 		return ret;
 	}
 
+	val = readl(ddata->regs + PWM_SIFIVE_PWMCFG);
+	if (val & PWM_SIFIVE_PWMCFG_EN_ALWAYS) {
+		unsigned int i;
+
+		for (i = 0; i < chip->npwm; ++i) {
+			val = readl(ddata->regs + PWM_SIFIVE_PWMCMP(i));
+			if (val > 0)
+				++enabled_pwms;
+		}
+	}
+
+	/* The clk should be on once for each running PWM. */
+	if (enabled_pwms) {
+		while (enabled_clks < enabled_pwms) {
+			/* This is not expected to fail as the clk is already on */
+			ret = clk_enable(ddata->clk);
+			if (unlikely(ret)) {
+				dev_err_probe(dev, ret, "Failed to enable clk\n");
+				goto disable_clk;
+			}
+			++enabled_clks;
+		}
+	} else {
+		clk_disable(ddata->clk);
+		enabled_clks = 0;
+	}
+
 	/* Watch for changes to underlying clock frequency */
 	ddata->notifier.notifier_call = pwm_sifive_clock_notifier;
 	ret = clk_notifier_register(ddata->clk, &ddata->notifier);
@@ -281,7 +317,11 @@
 unregister_clk:
 	clk_notifier_unregister(ddata->clk, &ddata->notifier);
 disable_clk:
-	clk_disable_unprepare(ddata->clk);
+	while (enabled_clks) {
+		clk_disable(ddata->clk);
+		--enabled_clks;
+	}
+	clk_unprepare(ddata->clk);
 
 	return ret;
 }
@@ -289,23 +329,19 @@
 static int pwm_sifive_remove(struct platform_device *dev)
 {
 	struct pwm_sifive_ddata *ddata = platform_get_drvdata(dev);
-	bool is_enabled = false;
 	struct pwm_device *pwm;
 	int ch;
 
+	pwmchip_remove(&ddata->chip);
+	clk_notifier_unregister(ddata->clk, &ddata->notifier);
+
 	for (ch = 0; ch < ddata->chip.npwm; ch++) {
 		pwm = &ddata->chip.pwms[ch];
-		if (pwm->state.enabled) {
-			is_enabled = true;
-			break;
-		}
+		if (pwm->state.enabled)
+			clk_disable(ddata->clk);
 	}
-	if (is_enabled)
-		clk_disable(ddata->clk);
 
-	clk_disable_unprepare(ddata->clk);
-	pwmchip_remove(&ddata->chip);
-	clk_notifier_unregister(ddata->clk, &ddata->notifier);
+	clk_unprepare(ddata->clk);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-sprd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-sprd.c
@@ -109,6 +109,7 @@
 	duty = val & SPRD_PWM_DUTY_MSK;
 	tmp = (prescale + 1) * NSEC_PER_SEC * duty;
 	state->duty_cycle = DIV_ROUND_CLOSEST_ULL(tmp, chn->clk_rate);
+	state->polarity = PWM_POLARITY_NORMAL;
 
 	/* Disable PWM clocks if the PWM channel is not in enable state. */
 	if (!state->enabled)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-sti.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-sti.c
@@ -79,6 +79,7 @@
 	unsigned int cpt_num_devs;
 	unsigned int max_pwm_cnt;
 	unsigned int max_prescale;
+	struct sti_cpt_ddata *ddata;
 };
 
 struct sti_pwm_chip {
@@ -314,7 +315,7 @@
 {
 	struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
 	struct sti_pwm_compat_data *cdata = pc->cdata;
-	struct sti_cpt_ddata *ddata = pwm_get_chip_data(pwm);
+	struct sti_cpt_ddata *ddata = &cdata->ddata[pwm->hwpwm];
 	struct device *dev = pc->dev;
 	unsigned int effective_ticks;
 	unsigned long long high, low;
@@ -391,11 +392,43 @@
 	return ret;
 }
 
+static int sti_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			 const struct pwm_state *state)
+{
+	struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
+	struct sti_pwm_compat_data *cdata = pc->cdata;
+	struct device *dev = pc->dev;
+	int err;
+
+	if (pwm->hwpwm >= cdata->pwm_num_devs) {
+		dev_err(dev, "device %u is not valid for pwm mode\n",
+			pwm->hwpwm);
+		return -EINVAL;
+	}
+
+	if (state->polarity != PWM_POLARITY_NORMAL)
+		return -EINVAL;
+
+	if (!state->enabled) {
+		if (pwm->state.enabled)
+			sti_pwm_disable(chip, pwm);
+
+		return 0;
+	}
+
+	err = sti_pwm_config(pwm->chip, pwm, state->duty_cycle, state->period);
+	if (err)
+		return err;
+
+	if (!pwm->state.enabled)
+		err = sti_pwm_enable(chip, pwm);
+
+	return err;
+}
+
 static const struct pwm_ops sti_pwm_ops = {
 	.capture = sti_pwm_capture,
-	.config = sti_pwm_config,
-	.enable = sti_pwm_enable,
-	.disable = sti_pwm_disable,
+	.apply = sti_pwm_apply,
 	.free = sti_pwm_free,
 	.owner = THIS_MODULE,
 };
@@ -417,7 +450,7 @@
 	while (cpt_int_stat) {
 		devicenum = ffs(cpt_int_stat) - 1;
 
-		ddata = pwm_get_chip_data(&pc->chip.pwms[devicenum]);
+		ddata = &pc->cdata->ddata[devicenum];
 
 		/*
 		 * Capture input:
@@ -538,6 +571,7 @@
 {
 	struct device *dev = &pdev->dev;
 	struct sti_pwm_compat_data *cdata;
+	struct pwm_chip *chip;
 	struct sti_pwm_chip *pc;
 	unsigned int i;
 	int irq, ret;
@@ -545,6 +579,7 @@
 	pc = devm_kzalloc(dev, sizeof(*pc), GFP_KERNEL);
 	if (!pc)
 		return -ENOMEM;
+	chip = &pc->chip;
 
 	cdata = devm_kzalloc(dev, sizeof(*cdata), GFP_KERNEL);
 	if (!cdata)
@@ -590,72 +625,37 @@
 		return ret;
 
 	if (cdata->pwm_num_devs) {
-		pc->pwm_clk = of_clk_get_by_name(dev->of_node, "pwm");
+		pc->pwm_clk = devm_clk_get_prepared(dev, "pwm");
 		if (IS_ERR(pc->pwm_clk)) {
 			dev_err(dev, "failed to get PWM clock\n");
 			return PTR_ERR(pc->pwm_clk);
 		}
-
-		ret = clk_prepare(pc->pwm_clk);
-		if (ret) {
-			dev_err(dev, "failed to prepare clock\n");
-			return ret;
-		}
 	}
 
 	if (cdata->cpt_num_devs) {
-		pc->cpt_clk = of_clk_get_by_name(dev->of_node, "capture");
+		pc->cpt_clk = devm_clk_get_prepared(dev, "capture");
 		if (IS_ERR(pc->cpt_clk)) {
 			dev_err(dev, "failed to get PWM capture clock\n");
 			return PTR_ERR(pc->cpt_clk);
 		}
 
-		ret = clk_prepare(pc->cpt_clk);
-		if (ret) {
-			dev_err(dev, "failed to prepare clock\n");
-			return ret;
-		}
+		cdata->ddata = devm_kzalloc(dev, cdata->cpt_num_devs * sizeof(*cdata->ddata), GFP_KERNEL);
+		if (!cdata->ddata)
+			return -ENOMEM;
 	}
 
-	pc->chip.dev = dev;
-	pc->chip.ops = &sti_pwm_ops;
-	pc->chip.npwm = pc->cdata->pwm_num_devs;
-
-	ret = pwmchip_add(&pc->chip);
-	if (ret < 0) {
-		clk_unprepare(pc->pwm_clk);
-		clk_unprepare(pc->cpt_clk);
-		return ret;
-	}
+	chip->dev = dev;
+	chip->ops = &sti_pwm_ops;
+	chip->npwm = max(cdata->pwm_num_devs, cdata->cpt_num_devs);
 
 	for (i = 0; i < cdata->cpt_num_devs; i++) {
-		struct sti_cpt_ddata *ddata;
-
-		ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
-		if (!ddata)
-			return -ENOMEM;
+		struct sti_cpt_ddata *ddata = &cdata->ddata[i];
 
 		init_waitqueue_head(&ddata->wait);
 		mutex_init(&ddata->lock);
-
-		pwm_set_chip_data(&pc->chip.pwms[i], ddata);
 	}
 
-	platform_set_drvdata(pdev, pc);
-
-	return 0;
-}
-
-static int sti_pwm_remove(struct platform_device *pdev)
-{
-	struct sti_pwm_chip *pc = platform_get_drvdata(pdev);
-
-	pwmchip_remove(&pc->chip);
-
-	clk_unprepare(pc->pwm_clk);
-	clk_unprepare(pc->cpt_clk);
-
-	return 0;
+	return devm_pwmchip_add(dev, chip);
 }
 
 static const struct of_device_id sti_pwm_of_match[] = {
@@ -670,7 +670,6 @@
 		.of_match_table = sti_pwm_of_match,
 	},
 	.probe = sti_pwm_probe,
-	.remove = sti_pwm_remove,
 };
 module_platform_driver(sti_pwm_driver);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-stm32-lp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-stm32-lp.c
@@ -127,7 +127,7 @@
 
 	/* ensure CMP & ARR registers are properly written */
 	ret = regmap_read_poll_timeout(priv->regmap, STM32_LPTIM_ISR, val,
-				       (val & STM32_LPTIM_CMPOK_ARROK),
+				       (val & STM32_LPTIM_CMPOK_ARROK) == STM32_LPTIM_CMPOK_ARROK,
 				       100, 1000);
 	if (ret) {
 		dev_err(priv->chip.dev, "ARR/CMP registers write issue\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-stm32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-stm32.c
@@ -115,14 +115,14 @@
 	int ret;
 
 	/* Ensure registers have been updated, enable counter and capture */
-	regmap_update_bits(priv->regmap, TIM_EGR, TIM_EGR_UG, TIM_EGR_UG);
-	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, TIM_CR1_CEN);
+	regmap_set_bits(priv->regmap, TIM_EGR, TIM_EGR_UG);
+	regmap_set_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);
 
 	/* Use cc1 or cc3 DMA resp for PWM input channels 1 & 2 or 3 & 4 */
 	dma_id = pwm->hwpwm < 2 ? STM32_TIMERS_DMA_CH1 : STM32_TIMERS_DMA_CH3;
 	ccen = pwm->hwpwm < 2 ? TIM_CCER_CC12E : TIM_CCER_CC34E;
 	ccr = pwm->hwpwm < 2 ? TIM_CCR1 : TIM_CCR3;
-	regmap_update_bits(priv->regmap, TIM_CCER, ccen, ccen);
+	regmap_set_bits(priv->regmap, TIM_CCER, ccen);
 
 	/*
 	 * Timer DMA burst mode. Request 2 registers, 2 bursts, to get both
@@ -160,8 +160,8 @@
 	}
 
 stop:
-	regmap_update_bits(priv->regmap, TIM_CCER, ccen, 0);
-	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0);
+	regmap_clear_bits(priv->regmap, TIM_CCER, ccen);
+	regmap_clear_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);
 
 	return ret;
 }
@@ -340,6 +340,9 @@
 
 	prd = div;
 
+	if (!prd)
+		return -EINVAL;
+
 	if (prescaler > MAX_TIM_PSC)
 		return -EINVAL;
 
@@ -359,7 +362,7 @@
 
 	regmap_write(priv->regmap, TIM_PSC, prescaler);
 	regmap_write(priv->regmap, TIM_ARR, prd - 1);
-	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, TIM_CR1_ARPE);
+	regmap_set_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE);
 
 	/* Calculate the duty cycles */
 	dty = prd * duty_ns;
@@ -377,7 +380,7 @@
 	else
 		regmap_update_bits(priv->regmap, TIM_CCMR2, mask, ccmr);
 
-	regmap_update_bits(priv->regmap, TIM_BDTR, TIM_BDTR_MOE, TIM_BDTR_MOE);
+	regmap_set_bits(priv->regmap, TIM_BDTR, TIM_BDTR_MOE);
 
 	return 0;
 }
@@ -411,13 +414,13 @@
 	if (priv->have_complementary_output)
 		mask |= TIM_CCER_CC1NE << (ch * 4);
 
-	regmap_update_bits(priv->regmap, TIM_CCER, mask, mask);
+	regmap_set_bits(priv->regmap, TIM_CCER, mask);
 
 	/* Make sure that registers are updated */
-	regmap_update_bits(priv->regmap, TIM_EGR, TIM_EGR_UG, TIM_EGR_UG);
+	regmap_set_bits(priv->regmap, TIM_EGR, TIM_EGR_UG);
 
 	/* Enable controller */
-	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, TIM_CR1_CEN);
+	regmap_set_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);
 
 	return 0;
 }
@@ -431,11 +434,11 @@
 	if (priv->have_complementary_output)
 		mask |= TIM_CCER_CC1NE << (ch * 4);
 
-	regmap_update_bits(priv->regmap, TIM_CCER, mask, 0);
+	regmap_clear_bits(priv->regmap, TIM_CCER, mask);
 
 	/* When all channels are disabled, we can disable the controller */
 	if (!active_channels(priv))
-		regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0);
+		regmap_clear_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);
 
 	clk_disable(priv->clk);
 }
@@ -449,8 +452,9 @@
 
 	enabled = pwm->state.enabled;
 
-	if (enabled && !state->enabled) {
-		stm32_pwm_disable(priv, pwm->hwpwm);
+	if (!state->enabled) {
+		if (enabled)
+			stm32_pwm_disable(priv, pwm->hwpwm);
 		return 0;
 	}
 
@@ -568,41 +572,30 @@
 	 * If complementary bit doesn't exist writing 1 will have no
 	 * effect so we can detect it.
 	 */
-	regmap_update_bits(priv->regmap,
-			   TIM_CCER, TIM_CCER_CC1NE, TIM_CCER_CC1NE);
+	regmap_set_bits(priv->regmap, TIM_CCER, TIM_CCER_CC1NE);
 	regmap_read(priv->regmap, TIM_CCER, &ccer);
-	regmap_update_bits(priv->regmap, TIM_CCER, TIM_CCER_CC1NE, 0);
+	regmap_clear_bits(priv->regmap, TIM_CCER, TIM_CCER_CC1NE);
 
 	priv->have_complementary_output = (ccer != 0);
 }
 
-static int stm32_pwm_detect_channels(struct stm32_pwm *priv)
+static unsigned int stm32_pwm_detect_channels(struct stm32_pwm *priv,
+					      unsigned int *num_enabled)
 {
-	u32 ccer;
-	int npwm = 0;
+	u32 ccer, ccer_backup;
 
 	/*
 	 * If channels enable bits don't exist writing 1 will have no
 	 * effect so we can detect and count them.
 	 */
-	regmap_update_bits(priv->regmap,
-			   TIM_CCER, TIM_CCER_CCXE, TIM_CCER_CCXE);
+	regmap_read(priv->regmap, TIM_CCER, &ccer_backup);
+	regmap_set_bits(priv->regmap, TIM_CCER, TIM_CCER_CCXE);
 	regmap_read(priv->regmap, TIM_CCER, &ccer);
-	regmap_update_bits(priv->regmap, TIM_CCER, TIM_CCER_CCXE, 0);
+	regmap_write(priv->regmap, TIM_CCER, ccer_backup);
 
-	if (ccer & TIM_CCER_CC1E)
-		npwm++;
+	*num_enabled = hweight32(ccer_backup & TIM_CCER_CCXE);
 
-	if (ccer & TIM_CCER_CC2E)
-		npwm++;
-
-	if (ccer & TIM_CCER_CC3E)
-		npwm++;
-
-	if (ccer & TIM_CCER_CC4E)
-		npwm++;
-
-	return npwm;
+	return hweight32(ccer & TIM_CCER_CCXE);
 }
 
 static int stm32_pwm_probe(struct platform_device *pdev)
@@ -611,6 +604,8 @@
 	struct device_node *np = dev->of_node;
 	struct stm32_timers *ddata = dev_get_drvdata(pdev->dev.parent);
 	struct stm32_pwm *priv;
+	unsigned int num_enabled;
+	unsigned int i;
 	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -633,7 +628,11 @@
 
 	priv->chip.dev = dev;
 	priv->chip.ops = &stm32pwm_ops;
-	priv->chip.npwm = stm32_pwm_detect_channels(priv);
+	priv->chip.npwm = stm32_pwm_detect_channels(priv, &num_enabled);
+
+	/* Initialize clock refcount to number of enabled PWM channels. */
+	for (i = 0; i < num_enabled; i++)
+		clk_enable(priv->clk);
 
 	ret = pwmchip_add(&priv->chip);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/pwm-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/pwm-tegra.c
@@ -142,8 +142,8 @@
 		 * source clock rate as required_clk_rate, PWM controller will
 		 * be able to configure the requested period.
 		 */
-		required_clk_rate =
-			(NSEC_PER_SEC / period_ns) << PWM_DUTY_WIDTH;
+		required_clk_rate = DIV_ROUND_UP_ULL((u64)NSEC_PER_SEC << PWM_DUTY_WIDTH,
+						     period_ns);
 
 		err = clk_set_rate(pc->clk, required_clk_rate);
 		if (err < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/pwm/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/pwm/sysfs.c
@@ -424,6 +424,13 @@
 		if (!export)
 			continue;
 
+		/* If pwmchip was not enabled before suspend, do nothing. */
+		if (!export->suspend.enabled) {
+			/* release lock taken in pwm_class_get_state */
+			mutex_unlock(&export->lock);
+			continue;
+		}
+
 		state.enabled = export->suspend.enabled;
 		ret = pwm_class_apply_state(export, pwm, &state);
 		if (ret < 0)
@@ -448,7 +455,17 @@
 		if (!export)
 			continue;
 
+		/*
+		 * If pwmchip was not enabled before suspend, save
+		 * state for resume time and do nothing else.
+		 */
 		export->suspend = state;
+		if (!state.enabled) {
+			/* release lock taken in pwm_class_get_state */
+			mutex_unlock(&export->lock);
+			continue;
+		}
+
 		state.enabled = false;
 		ret = pwm_class_apply_state(export, pwm, &state);
 		if (ret < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rapidio/devices/rio_mport_cdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rapidio/devices/rio_mport_cdev.c
@@ -1739,7 +1739,8 @@
 		err = rio_add_net(net);
 		if (err) {
 			rmcd_debug(RDEV, "failed to register net, err=%d", err);
-			kfree(net);
+			put_device(&net->dev);
+			mport->net = NULL;
 			goto cleanup;
 		}
 	}
@@ -1803,8 +1804,11 @@
 		rio_init_dbell_res(&rdev->riores[RIO_DOORBELL_RESOURCE],
 				   0, 0xffff);
 	err = rio_add_device(rdev);
-	if (err)
-		goto cleanup;
+	if (err) {
+		put_device(&rdev->dev);
+		return err;
+	}
+
 	rio_dev_get(rdev);
 
 	return 0;
@@ -1900,10 +1904,6 @@
 
 	priv->md = chdev;
 
-	mutex_lock(&chdev->file_mutex);
-	list_add_tail(&priv->list, &chdev->file_list);
-	mutex_unlock(&chdev->file_mutex);
-
 	INIT_LIST_HEAD(&priv->db_filters);
 	INIT_LIST_HEAD(&priv->pw_filters);
 	spin_lock_init(&priv->fifo_lock);
@@ -1912,6 +1912,7 @@
 			  sizeof(struct rio_event) * MPORT_EVENT_DEPTH,
 			  GFP_KERNEL);
 	if (ret < 0) {
+		put_device(&chdev->dev);
 		dev_err(&chdev->dev, DRV_NAME ": kfifo_alloc failed\n");
 		ret = -ENOMEM;
 		goto err_fifo;
@@ -1922,6 +1923,9 @@
 	spin_lock_init(&priv->req_lock);
 	mutex_init(&priv->dma_lock);
 #endif
+	mutex_lock(&chdev->file_mutex);
+	list_add_tail(&priv->list, &chdev->file_list);
+	mutex_unlock(&chdev->file_mutex);
 
 	filp->private_data = priv;
 	goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rapidio/rio-scan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rapidio/rio-scan.c
@@ -454,8 +454,12 @@
 				   0, 0xffff);
 
 	ret = rio_add_device(rdev);
-	if (ret)
-		goto cleanup;
+	if (ret) {
+		if (rswitch)
+			kfree(rswitch->route_table);
+		put_device(&rdev->dev);
+		return NULL;
+	}
 
 	rio_dev_get(rdev);
 
@@ -867,7 +871,10 @@
 		dev_set_name(&net->dev, "rnet_%d", net->id);
 		net->dev.parent = &mport->dev;
 		net->dev.release = rio_scan_release_dev;
-		rio_add_net(net);
+		if (rio_add_net(net)) {
+			put_device(&net->dev);
+			net = NULL;
+		}
 	}
 
 	return net;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rapidio/rio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rapidio/rio.c
@@ -2186,11 +2186,16 @@
 	atomic_set(&port->state, RIO_DEVICE_RUNNING);
 
 	res = device_register(&port->dev);
-	if (res)
+	if (res) {
 		dev_err(&port->dev, "RIO: mport%d registration failed ERR=%d\n",
 			port->id, res);
-	else
+		mutex_lock(&rio_mport_list_lock);
+		list_del(&port->node);
+		mutex_unlock(&rio_mport_list_lock);
+		put_device(&port->dev);
+	} else {
 		dev_dbg(&port->dev, "RIO: registered mport%d\n", port->id);
+	}
 
 	return res;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/atc260x-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/atc260x-regulator.c
@@ -292,6 +292,7 @@
 	.bypass_mask = BIT(5), \
 	.active_discharge_reg = ATC2603C_PMU_SWITCH_CTL, \
 	.active_discharge_mask = BIT(1), \
+	.active_discharge_on = BIT(1), \
 	.owner = THIS_MODULE, \
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/bd71815-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/bd71815-regulator.c
@@ -257,7 +257,7 @@
  * 10: 2.50mV/usec	10mV 4uS
  * 11: 1.25mV/usec	10mV 8uS
  */
-static const unsigned int bd7181x_ramp_table[] = { 1250, 2500, 5000, 10000 };
+static const unsigned int bd7181x_ramp_table[] = { 10000, 5000, 2500, 1250 };
 
 static int bd7181x_led_set_current_limit(struct regulator_dev *rdev,
 					int min_uA, int max_uA)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/bd71828-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/bd71828-regulator.c
@@ -207,14 +207,11 @@
 			.suspend_reg = BD71828_REG_BUCK1_SUSP_VOLT,
 			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
-			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
 			/*
 			 * LPSR voltage is same as SUSPEND voltage. Allow
-			 * setting it so that regulator can be set enabled at
-			 * LPSR state
+			 * only enabling/disabling regulator for LPSR state
 			 */
-			.lpsr_reg = BD71828_REG_BUCK1_SUSP_VOLT,
-			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
 		},
 		.reg_inits = buck1_inits,
 		.reg_init_amnt = ARRAY_SIZE(buck1_inits),
@@ -289,13 +286,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_BUCK3_VOLT,
-			.idle_reg = BD71828_REG_BUCK3_VOLT,
-			.suspend_reg = BD71828_REG_BUCK3_VOLT,
-			.lpsr_reg = BD71828_REG_BUCK3_VOLT,
 			.run_mask = BD71828_MASK_BUCK3_VOLT,
-			.idle_mask = BD71828_MASK_BUCK3_VOLT,
-			.suspend_mask = BD71828_MASK_BUCK3_VOLT,
-			.lpsr_mask = BD71828_MASK_BUCK3_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -330,13 +321,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_BUCK4_VOLT,
-			.idle_reg = BD71828_REG_BUCK4_VOLT,
-			.suspend_reg = BD71828_REG_BUCK4_VOLT,
-			.lpsr_reg = BD71828_REG_BUCK4_VOLT,
 			.run_mask = BD71828_MASK_BUCK4_VOLT,
-			.idle_mask = BD71828_MASK_BUCK4_VOLT,
-			.suspend_mask = BD71828_MASK_BUCK4_VOLT,
-			.lpsr_mask = BD71828_MASK_BUCK4_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -371,13 +356,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_BUCK5_VOLT,
-			.idle_reg = BD71828_REG_BUCK5_VOLT,
-			.suspend_reg = BD71828_REG_BUCK5_VOLT,
-			.lpsr_reg = BD71828_REG_BUCK5_VOLT,
 			.run_mask = BD71828_MASK_BUCK5_VOLT,
-			.idle_mask = BD71828_MASK_BUCK5_VOLT,
-			.suspend_mask = BD71828_MASK_BUCK5_VOLT,
-			.lpsr_mask = BD71828_MASK_BUCK5_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -494,13 +473,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_LDO1_VOLT,
-			.idle_reg = BD71828_REG_LDO1_VOLT,
-			.suspend_reg = BD71828_REG_LDO1_VOLT,
-			.lpsr_reg = BD71828_REG_LDO1_VOLT,
 			.run_mask = BD71828_MASK_LDO_VOLT,
-			.idle_mask = BD71828_MASK_LDO_VOLT,
-			.suspend_mask = BD71828_MASK_LDO_VOLT,
-			.lpsr_mask = BD71828_MASK_LDO_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -534,13 +507,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_LDO2_VOLT,
-			.idle_reg = BD71828_REG_LDO2_VOLT,
-			.suspend_reg = BD71828_REG_LDO2_VOLT,
-			.lpsr_reg = BD71828_REG_LDO2_VOLT,
 			.run_mask = BD71828_MASK_LDO_VOLT,
-			.idle_mask = BD71828_MASK_LDO_VOLT,
-			.suspend_mask = BD71828_MASK_LDO_VOLT,
-			.lpsr_mask = BD71828_MASK_LDO_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -574,13 +541,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_LDO3_VOLT,
-			.idle_reg = BD71828_REG_LDO3_VOLT,
-			.suspend_reg = BD71828_REG_LDO3_VOLT,
-			.lpsr_reg = BD71828_REG_LDO3_VOLT,
 			.run_mask = BD71828_MASK_LDO_VOLT,
-			.idle_mask = BD71828_MASK_LDO_VOLT,
-			.suspend_mask = BD71828_MASK_LDO_VOLT,
-			.lpsr_mask = BD71828_MASK_LDO_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -615,13 +576,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_LDO4_VOLT,
-			.idle_reg = BD71828_REG_LDO4_VOLT,
-			.suspend_reg = BD71828_REG_LDO4_VOLT,
-			.lpsr_reg = BD71828_REG_LDO4_VOLT,
 			.run_mask = BD71828_MASK_LDO_VOLT,
-			.idle_mask = BD71828_MASK_LDO_VOLT,
-			.suspend_mask = BD71828_MASK_LDO_VOLT,
-			.lpsr_mask = BD71828_MASK_LDO_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -656,13 +611,7 @@
 				     ROHM_DVS_LEVEL_SUSPEND |
 				     ROHM_DVS_LEVEL_LPSR,
 			.run_reg = BD71828_REG_LDO5_VOLT,
-			.idle_reg = BD71828_REG_LDO5_VOLT,
-			.suspend_reg = BD71828_REG_LDO5_VOLT,
-			.lpsr_reg = BD71828_REG_LDO5_VOLT,
 			.run_mask = BD71828_MASK_LDO_VOLT,
-			.idle_mask = BD71828_MASK_LDO_VOLT,
-			.suspend_mask = BD71828_MASK_LDO_VOLT,
-			.lpsr_mask = BD71828_MASK_LDO_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
@@ -721,9 +670,6 @@
 			.suspend_reg = BD71828_REG_LDO7_VOLT,
 			.lpsr_reg = BD71828_REG_LDO7_VOLT,
 			.run_mask = BD71828_MASK_LDO_VOLT,
-			.idle_mask = BD71828_MASK_LDO_VOLT,
-			.suspend_mask = BD71828_MASK_LDO_VOLT,
-			.lpsr_mask = BD71828_MASK_LDO_VOLT,
 			.idle_on_mask = BD71828_MASK_IDLE_EN,
 			.suspend_on_mask = BD71828_MASK_SUSP_EN,
 			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/core.c
@@ -206,6 +206,78 @@
 	mutex_unlock(&regulator_nesting_mutex);
 }
 
+/**
+ * regulator_lock_two - lock two regulators
+ * @rdev1:		first regulator
+ * @rdev2:		second regulator
+ * @ww_ctx:		w/w mutex acquire context
+ *
+ * Locks both rdevs using the regulator_ww_class.
+ */
+static void regulator_lock_two(struct regulator_dev *rdev1,
+			       struct regulator_dev *rdev2,
+			       struct ww_acquire_ctx *ww_ctx)
+{
+	struct regulator_dev *tmp;
+	int ret;
+
+	ww_acquire_init(ww_ctx, &regulator_ww_class);
+
+	/* Try to just grab both of them */
+	ret = regulator_lock_nested(rdev1, ww_ctx);
+	WARN_ON(ret);
+	ret = regulator_lock_nested(rdev2, ww_ctx);
+	if (ret != -EDEADLOCK) {
+		WARN_ON(ret);
+		goto exit;
+	}
+
+	while (true) {
+		/*
+		 * Start of loop: rdev1 was locked and rdev2 was contended.
+		 * Need to unlock rdev1, slowly lock rdev2, then try rdev1
+		 * again.
+		 */
+		regulator_unlock(rdev1);
+
+		ww_mutex_lock_slow(&rdev2->mutex, ww_ctx);
+		rdev2->ref_cnt++;
+		rdev2->mutex_owner = current;
+		ret = regulator_lock_nested(rdev1, ww_ctx);
+
+		if (ret == -EDEADLOCK) {
+			/* More contention; swap which needs to be slow */
+			tmp = rdev1;
+			rdev1 = rdev2;
+			rdev2 = tmp;
+		} else {
+			WARN_ON(ret);
+			break;
+		}
+	}
+
+exit:
+	ww_acquire_done(ww_ctx);
+}
+
+/**
+ * regulator_unlock_two - unlock two regulators
+ * @rdev1:		first regulator
+ * @rdev2:		second regulator
+ * @ww_ctx:		w/w mutex acquire context
+ *
+ * The inverse of regulator_lock_two().
+ */
+
+static void regulator_unlock_two(struct regulator_dev *rdev1,
+				 struct regulator_dev *rdev2,
+				 struct ww_acquire_ctx *ww_ctx)
+{
+	regulator_unlock(rdev2);
+	regulator_unlock(rdev1);
+	ww_acquire_fini(ww_ctx);
+}
+
 static bool regulator_supply_is_couple(struct regulator_dev *rdev)
 {
 	struct regulator_dev *c_rdev;
@@ -333,6 +405,7 @@
 			ww_mutex_lock_slow(&new_contended_rdev->mutex, ww_ctx);
 			old_contended_rdev = new_contended_rdev;
 			old_contended_rdev->ref_cnt++;
+			old_contended_rdev->mutex_owner = current;
 		}
 
 		err = regulator_lock_recursive(rdev,
@@ -962,7 +1035,7 @@
 		/* get input voltage */
 		input_uV = 0;
 		if (rdev->supply)
-			input_uV = regulator_get_voltage(rdev->supply);
+			input_uV = regulator_get_voltage_rdev(rdev->supply->rdev);
 		if (input_uV <= 0)
 			input_uV = rdev->constraints->input_uV;
 		if (input_uV <= 0) {
@@ -1521,6 +1594,24 @@
 		}
 	}
 
+	/*
+	 * If there is no mechanism for controlling the regulator then
+	 * flag it as always_on so we don't end up duplicating checks
+	 * for this so much.  Note that we could control the state of
+	 * a supply to control the output on a regulator that has no
+	 * direct control.
+	 */
+	if (!rdev->ena_pin && !ops->enable) {
+		if (rdev->supply_name && !rdev->supply)
+			return -EPROBE_DEFER;
+
+		if (rdev->supply)
+			rdev->constraints->always_on =
+				rdev->supply->rdev->constraints->always_on;
+		else
+			rdev->constraints->always_on = true;
+	}
+
 	/* If the constraints say the regulator should be on at this point
 	 * and we have control then make sure it is enabled.
 	 */
@@ -1531,7 +1622,13 @@
 		if (rdev->supply_name && !rdev->supply)
 			return -EPROBE_DEFER;
 
-		if (rdev->supply) {
+		/* If supplying regulator has already been enabled,
+		 * it's not intended to have use_count increment
+		 * when rdev is only boot-on.
+		 */
+		if (rdev->supply &&
+		    (rdev->constraints->always_on ||
+		     !regulator_is_enabled(rdev->supply))) {
 			ret = regulator_enable(rdev->supply);
 			if (ret < 0) {
 				_regulator_put(rdev->supply);
@@ -1558,8 +1655,8 @@
 
 /**
  * set_supply - set regulator supply regulator
- * @rdev: regulator name
- * @supply_rdev: supply regulator name
+ * @rdev: regulator (locked)
+ * @supply_rdev: supply regulator (locked))
  *
  * Called by platform initialisation code to set the supply regulator for this
  * regulator. This ensures that a regulators supply will also be enabled by the
@@ -1577,6 +1674,7 @@
 
 	rdev->supply = create_regulator(supply_rdev, &rdev->dev, "SUPPLY");
 	if (rdev->supply == NULL) {
+		module_put(supply_rdev->owner);
 		err = -ENOMEM;
 		return err;
 	}
@@ -1730,6 +1828,8 @@
 	struct regulator *regulator;
 	int err = 0;
 
+	lockdep_assert_held_once(&rdev->mutex.base);
+
 	if (dev) {
 		char buf[REG_STR_SIZE];
 		int size;
@@ -1750,16 +1850,14 @@
 
 	regulator = kzalloc(sizeof(*regulator), GFP_KERNEL);
 	if (regulator == NULL) {
-		kfree(supply_name);
+		kfree_const(supply_name);
 		return NULL;
 	}
 
 	regulator->rdev = rdev;
 	regulator->supply_name = supply_name;
 
-	regulator_lock(rdev);
 	list_add(&regulator->list, &rdev->consumer_list);
-	regulator_unlock(rdev);
 
 	if (dev) {
 		regulator->dev = dev;
@@ -1774,20 +1872,23 @@
 		}
 	}
 
-	if (err != -EEXIST)
+	if (err != -EEXIST) {
 		regulator->debugfs = debugfs_create_dir(supply_name, rdev->debugfs);
-	if (!regulator->debugfs) {
-		rdev_dbg(rdev, "Failed to create debugfs directory\n");
-	} else {
+		if (IS_ERR(regulator->debugfs)) {
+			rdev_dbg(rdev, "Failed to create debugfs directory\n");
+			regulator->debugfs = NULL;
+		}
+	}
+
+	if (regulator->debugfs) {
 		debugfs_create_u32("uA_load", 0444, regulator->debugfs,
 				   &regulator->uA_load);
 		debugfs_create_u32("min_uV", 0444, regulator->debugfs,
 				   &regulator->voltage[PM_SUSPEND_ON].min_uV);
 		debugfs_create_u32("max_uV", 0444, regulator->debugfs,
 				   &regulator->voltage[PM_SUSPEND_ON].max_uV);
-		debugfs_create_file("constraint_flags", 0444,
-				    regulator->debugfs, regulator,
-				    &constraint_flags_fops);
+		debugfs_create_file("constraint_flags", 0444, regulator->debugfs,
+				    regulator, &constraint_flags_fops);
 	}
 
 	/*
@@ -1880,6 +1981,7 @@
 		node = of_get_regulator(dev, supply);
 		if (node) {
 			r = of_find_regulator_by_node(node);
+			of_node_put(node);
 			if (r)
 				return r;
 
@@ -1924,6 +2026,7 @@
 {
 	struct regulator_dev *r;
 	struct device *dev = rdev->dev.parent;
+	struct ww_acquire_ctx ww_ctx;
 	int ret = 0;
 
 	/* No supply to resolve? */
@@ -1944,6 +2047,10 @@
 
 		if (have_full_constraints()) {
 			r = dummy_regulator_rdev;
+			if (!r) {
+				ret = -EPROBE_DEFER;
+				goto out;
+			}
 			get_device(&r->dev);
 		} else {
 			dev_err(dev, "Failed to resolve %s-supply for %s\n",
@@ -1961,6 +2068,10 @@
 			goto out;
 		}
 		r = dummy_regulator_rdev;
+		if (!r) {
+			ret = -EPROBE_DEFER;
+			goto out;
+		}
 		get_device(&r->dev);
 	}
 
@@ -1990,23 +2101,23 @@
 	 * between rdev->supply null check and setting rdev->supply in
 	 * set_supply() from concurrent tasks.
 	 */
-	regulator_lock(rdev);
+	regulator_lock_two(rdev, r, &ww_ctx);
 
 	/* Supply just resolved by a concurrent task? */
 	if (rdev->supply) {
-		regulator_unlock(rdev);
+		regulator_unlock_two(rdev, r, &ww_ctx);
 		put_device(&r->dev);
 		goto out;
 	}
 
 	ret = set_supply(rdev, r);
 	if (ret < 0) {
-		regulator_unlock(rdev);
+		regulator_unlock_two(rdev, r, &ww_ctx);
 		put_device(&r->dev);
 		goto out;
 	}
 
-	regulator_unlock(rdev);
+	regulator_unlock_two(rdev, r, &ww_ctx);
 
 	/*
 	 * In set_machine_constraints() we may have turned this regulator on
@@ -2069,8 +2180,10 @@
 			 * enabled, even if it isn't hooked up, and just
 			 * provide a dummy.
 			 */
-			dev_warn(dev, "supply %s not found, using dummy regulator\n", id);
 			rdev = dummy_regulator_rdev;
+			if (!rdev)
+				return ERR_PTR(-EPROBE_DEFER);
+			dev_warn(dev, "supply %s not found, using dummy regulator\n", id);
 			get_device(&rdev->dev);
 			break;
 
@@ -2119,7 +2232,9 @@
 		return regulator;
 	}
 
+	regulator_lock(rdev);
 	regulator = create_regulator(rdev, dev, id);
+	regulator_unlock(rdev);
 	if (regulator == NULL) {
 		regulator = ERR_PTR(-ENOMEM);
 		module_put(rdev->owner);
@@ -2132,10 +2247,13 @@
 		rdev->exclusive = 1;
 
 		ret = _regulator_is_enabled(rdev);
-		if (ret > 0)
+		if (ret > 0) {
 			rdev->use_count = 1;
-		else
+			regulator->enable_count = 1;
+		} else {
 			rdev->use_count = 0;
+			regulator->enable_count = 0;
+		}
 	}
 
 	link = device_link_add(dev, &rdev->dev, DL_FLAG_STATELESS);
@@ -2594,12 +2712,12 @@
 
 	trace_regulator_enable(rdev_get_name(rdev));
 
-	if (rdev->desc->off_on_delay && rdev->last_off) {
+	if (rdev->desc->off_on_delay) {
 		/* if needed, keep a distance of off_on_delay from last time
 		 * this regulator was disabled.
 		 */
 		ktime_t end = ktime_add_us(rdev->last_off, rdev->desc->off_on_delay);
-		s64 remaining = ktime_us_delta(end, ktime_get());
+		s64 remaining = ktime_us_delta(end, ktime_get_boottime());
 
 		if (remaining > 0)
 			_regulator_enable_delay(remaining);
@@ -2633,7 +2751,7 @@
 	 * expired, return -ETIMEDOUT.
 	 */
 	if (rdev->desc->poll_enabled_time) {
-		unsigned int time_remaining = delay;
+		int time_remaining = delay;
 
 		while (time_remaining > 0) {
 			_regulator_enable_delay(rdev->desc->poll_enabled_time);
@@ -2685,13 +2803,18 @@
  */
 static int _regulator_handle_consumer_enable(struct regulator *regulator)
 {
+	int ret;
 	struct regulator_dev *rdev = regulator->rdev;
 
 	lockdep_assert_held_once(&rdev->mutex.base);
 
 	regulator->enable_count++;
-	if (regulator->uA_load && regulator->enable_count == 1)
-		return drms_uA_update(rdev);
+	if (regulator->uA_load && regulator->enable_count == 1) {
+		ret = drms_uA_update(rdev);
+		if (ret)
+			regulator->enable_count--;
+		return ret;
+	}
 
 	return 0;
 }
@@ -2773,7 +2896,8 @@
 		/* Fallthrough on positive return values - already enabled */
 	}
 
-	rdev->use_count++;
+	if (regulator->enable_count == 1)
+		rdev->use_count++;
 
 	return 0;
 
@@ -2833,7 +2957,7 @@
 	}
 
 	if (rdev->desc->off_on_delay)
-		rdev->last_off = ktime_get();
+		rdev->last_off = ktime_get_boottime();
 
 	trace_regulator_disable_complete(rdev_get_name(rdev));
 
@@ -2848,37 +2972,40 @@
 
 	lockdep_assert_held_once(&rdev->mutex.base);
 
-	if (WARN(rdev->use_count <= 0,
+	if (WARN(regulator->enable_count == 0,
 		 "unbalanced disables for %s\n", rdev_get_name(rdev)))
 		return -EIO;
 
-	/* are we the last user and permitted to disable ? */
-	if (rdev->use_count == 1 &&
-	    (rdev->constraints && !rdev->constraints->always_on)) {
-
-		/* we are last user */
-		if (regulator_ops_is_valid(rdev, REGULATOR_CHANGE_STATUS)) {
-			ret = _notifier_call_chain(rdev,
-						   REGULATOR_EVENT_PRE_DISABLE,
-						   NULL);
-			if (ret & NOTIFY_STOP_MASK)
-				return -EINVAL;
-
-			ret = _regulator_do_disable(rdev);
-			if (ret < 0) {
-				rdev_err(rdev, "failed to disable: %pe\n", ERR_PTR(ret));
-				_notifier_call_chain(rdev,
-						REGULATOR_EVENT_ABORT_DISABLE,
+	if (regulator->enable_count == 1) {
+	/* disabling last enable_count from this regulator */
+		/* are we the last user and permitted to disable ? */
+		if (rdev->use_count == 1 &&
+		    (rdev->constraints && !rdev->constraints->always_on)) {
+
+			/* we are last user */
+			if (regulator_ops_is_valid(rdev, REGULATOR_CHANGE_STATUS)) {
+				ret = _notifier_call_chain(rdev,
+							   REGULATOR_EVENT_PRE_DISABLE,
+							   NULL);
+				if (ret & NOTIFY_STOP_MASK)
+					return -EINVAL;
+
+				ret = _regulator_do_disable(rdev);
+				if (ret < 0) {
+					rdev_err(rdev, "failed to disable: %pe\n", ERR_PTR(ret));
+					_notifier_call_chain(rdev,
+							REGULATOR_EVENT_ABORT_DISABLE,
+							NULL);
+					return ret;
+				}
+				_notifier_call_chain(rdev, REGULATOR_EVENT_DISABLE,
 						NULL);
-				return ret;
 			}
-			_notifier_call_chain(rdev, REGULATOR_EVENT_DISABLE,
-					NULL);
-		}
 
-		rdev->use_count = 0;
-	} else if (rdev->use_count > 1) {
-		rdev->use_count--;
+			rdev->use_count = 0;
+		} else if (rdev->use_count > 1) {
+			rdev->use_count--;
+		}
 	}
 
 	if (ret == 0)
@@ -3180,6 +3307,7 @@
 
 	return map ? map : ERR_PTR(-EOPNOTSUPP);
 }
+EXPORT_SYMBOL_GPL(regulator_get_regmap);
 
 /**
  * regulator_get_hardware_vsel_register - get the HW voltage selector register
@@ -5063,6 +5191,7 @@
 {
 	struct regulator_dev *rdev = dev_get_drvdata(dev);
 
+	debugfs_remove_recursive(rdev->debugfs);
 	kfree(rdev->constraints);
 	of_node_put(rdev->dev.of_node);
 	kfree(rdev);
@@ -5082,10 +5211,8 @@
 	}
 
 	rdev->debugfs = debugfs_create_dir(rname, debugfs_root);
-	if (!rdev->debugfs) {
-		rdev_warn(rdev, "Failed to create debugfs directory\n");
-		return;
-	}
+	if (IS_ERR(rdev->debugfs))
+		rdev_dbg(rdev, "Failed to create debugfs directory\n");
 
 	debugfs_create_u32("use_count", 0444, rdev->debugfs,
 			   &rdev->use_count);
@@ -5537,6 +5664,7 @@
 	regulator_remove_coupling(rdev);
 	mutex_unlock(&regulator_list_mutex);
 wash:
+	regulator_put(rdev->supply);
 	kfree(rdev->coupling_desc.coupled_rdevs);
 	mutex_lock(&regulator_list_mutex);
 	regulator_ena_gpio_free(rdev);
@@ -5574,7 +5702,6 @@
 
 	mutex_lock(&regulator_list_mutex);
 
-	debugfs_remove_recursive(rdev->debugfs);
 	WARN_ON(rdev->open_count);
 	regulator_remove_coupling(rdev);
 	unset_regulator_supplies(rdev);
@@ -5927,6 +6054,7 @@
 			ww_mutex_lock_slow(&new_contended_rdev->mutex, ww_ctx);
 			old_contended_rdev = new_contended_rdev;
 			old_contended_rdev->ref_cnt++;
+			old_contended_rdev->mutex_owner = current;
 		}
 
 		err = regulator_summary_lock_all(ww_ctx,
@@ -5987,8 +6115,8 @@
 	ret = class_register(&regulator_class);
 
 	debugfs_root = debugfs_create_dir("regulator", NULL);
-	if (!debugfs_root)
-		pr_warn("regulator: Failed to create debugfs directory\n");
+	if (IS_ERR(debugfs_root))
+		pr_debug("regulator: Failed to create debugfs directory\n");
 
 #ifdef CONFIG_DEBUG_FS
 	debugfs_create_file("supply_map", 0444, debugfs_root, NULL,
@@ -6010,9 +6138,8 @@
 static int regulator_late_cleanup(struct device *dev, void *data)
 {
 	struct regulator_dev *rdev = dev_to_rdev(dev);
-	const struct regulator_ops *ops = rdev->desc->ops;
 	struct regulation_constraints *c = rdev->constraints;
-	int enabled, ret;
+	int ret;
 
 	if (c && c->always_on)
 		return 0;
@@ -6025,14 +6152,8 @@
 	if (rdev->use_count)
 		goto unlock;
 
-	/* If we can't read the status assume it's always on. */
-	if (ops->is_enabled)
-		enabled = ops->is_enabled(rdev);
-	else
-		enabled = 1;
-
-	/* But if reading the status failed, assume that it's off. */
-	if (enabled <= 0)
+	/* If reading the status failed, assume that it's off. */
+	if (_regulator_is_enabled(rdev) <= 0)
 		goto unlock;
 
 	if (have_full_constraints()) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/da9121-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/da9121-regulator.c
@@ -253,6 +253,11 @@
 		goto error;
 	}
 
+	if (rdev->desc->ops->is_enabled(rdev)) {
+		ret = -EBUSY;
+		goto error;
+	}
+
 	ret = da9121_ceiling_selector(rdev, min_ua, max_ua, &sel);
 	if (ret < 0)
 		goto error;
@@ -931,6 +936,8 @@
 		chip->variant_id = DA9121_TYPE_DA9220_DA9132;
 		regmap = &da9121_2ch_regmap_config;
 		break;
+	default:
+		return -EINVAL;
 	}
 
 	/* Set these up for of_regulator_match call which may want .of_map_modes */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/da9211-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/da9211-regulator.c
@@ -498,6 +498,12 @@
 
 	chip->chip_irq = i2c->irq;
 
+	ret = da9211_regulator_init(chip);
+	if (ret < 0) {
+		dev_err(chip->dev, "Failed to initialize regulator: %d\n", ret);
+		return ret;
+	}
+
 	if (chip->chip_irq != 0) {
 		ret = devm_request_threaded_irq(chip->dev, chip->chip_irq, NULL,
 					da9211_irq_handler,
@@ -512,11 +518,6 @@
 		dev_warn(chip->dev, "No IRQ configured\n");
 	}
 
-	ret = da9211_regulator_init(chip);
-
-	if (ret < 0)
-		dev_err(chip->dev, "Failed to initialize regulator: %d\n", ret);
-
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/fan53555.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/fan53555.c
@@ -8,18 +8,19 @@
 // Copyright (c) 2012 Marvell Technology Ltd.
 // Yunfan Zhang <yfzhang@marvell.com>
 
+#include <linux/bits.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/param.h>
-#include <linux/err.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/regulator/driver.h>
+#include <linux/regulator/fan53555.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
-#include <linux/of_device.h>
-#include <linux/i2c.h>
 #include <linux/slab.h>
-#include <linux/regmap.h>
-#include <linux/regulator/fan53555.h>
 
 /* Voltage setting */
 #define FAN53555_VSEL0		0x00
@@ -60,7 +61,7 @@
 #define TCS_VSEL1_MODE		(1 << 6)
 
 #define TCS_SLEW_SHIFT		3
-#define TCS_SLEW_MASK		(0x3 < 3)
+#define TCS_SLEW_MASK		GENMASK(4, 3)
 
 enum fan53555_vendor {
 	FAN53526_VENDOR_FAIRCHILD = 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/fixed.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/fixed.c
@@ -215,7 +215,7 @@
 		drvdata->enable_clock = devm_clk_get(dev, NULL);
 		if (IS_ERR(drvdata->enable_clock)) {
 			dev_err(dev, "Can't get enable-clock from devicetree\n");
-			return -ENOENT;
+			return PTR_ERR(drvdata->enable_clock);
 		}
 	} else if (drvtype && drvtype->has_performance_state) {
 		drvdata->desc.ops = &fixed_voltage_domain_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/irq_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/irq_helpers.c
@@ -350,6 +350,9 @@
 
 	h->irq = irq;
 	h->desc = *d;
+	h->desc.name = devm_kstrdup(dev, d->name, GFP_KERNEL);
+	if (!h->desc.name)
+		return ERR_PTR(-ENOMEM);
 
 	ret = init_rdev_state(dev, h, rdev, common_errs, per_rdev_errs,
 			      rdev_amount);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/max77802-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/max77802-regulator.c
@@ -94,9 +94,11 @@
 {
 	unsigned int val = MAX77802_OFF_PWRREQ;
 	struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev);
-	int id = rdev_get_id(rdev);
+	unsigned int id = rdev_get_id(rdev);
 	int shift = max77802_get_opmode_shift(id);
 
+	if (WARN_ON_ONCE(id >= ARRAY_SIZE(max77802->opmode)))
+		return -EINVAL;
 	max77802->opmode[id] = val;
 	return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
 				  rdev->desc->enable_mask, val << shift);
@@ -110,7 +112,7 @@
 static int max77802_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
 	struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev);
-	int id = rdev_get_id(rdev);
+	unsigned int id = rdev_get_id(rdev);
 	unsigned int val;
 	int shift = max77802_get_opmode_shift(id);
 
@@ -127,6 +129,9 @@
 		return -EINVAL;
 	}
 
+	if (WARN_ON_ONCE(id >= ARRAY_SIZE(max77802->opmode)))
+		return -EINVAL;
+
 	max77802->opmode[id] = val;
 	return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
 				  rdev->desc->enable_mask, val << shift);
@@ -135,8 +140,10 @@
 static unsigned max77802_get_mode(struct regulator_dev *rdev)
 {
 	struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev);
-	int id = rdev_get_id(rdev);
+	unsigned int id = rdev_get_id(rdev);
 
+	if (WARN_ON_ONCE(id >= ARRAY_SIZE(max77802->opmode)))
+		return -EINVAL;
 	return max77802_map_mode(max77802->opmode[id]);
 }
 
@@ -160,10 +167,13 @@
 				     unsigned int mode)
 {
 	struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev);
-	int id = rdev_get_id(rdev);
+	unsigned int id = rdev_get_id(rdev);
 	unsigned int val;
 	int shift = max77802_get_opmode_shift(id);
 
+	if (WARN_ON_ONCE(id >= ARRAY_SIZE(max77802->opmode)))
+		return -EINVAL;
+
 	/*
 	 * If the regulator has been disabled for suspend
 	 * then is invalid to try setting a suspend mode.
@@ -209,9 +219,11 @@
 static int max77802_enable(struct regulator_dev *rdev)
 {
 	struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev);
-	int id = rdev_get_id(rdev);
+	unsigned int id = rdev_get_id(rdev);
 	int shift = max77802_get_opmode_shift(id);
 
+	if (WARN_ON_ONCE(id >= ARRAY_SIZE(max77802->opmode)))
+		return -EINVAL;
 	if (max77802->opmode[id] == MAX77802_OFF_PWRREQ)
 		max77802->opmode[id] = MAX77802_OPMODE_NORMAL;
 
@@ -495,7 +507,7 @@
 
 	for (i = 0; i < MAX77802_REG_MAX; i++) {
 		struct regulator_dev *rdev;
-		int id = regulators[i].id;
+		unsigned int id = regulators[i].id;
 		int shift = max77802_get_opmode_shift(id);
 		int ret;
 
@@ -513,10 +525,12 @@
 		 * the hardware reports OFF as the regulator operating mode.
 		 * Default to operating mode NORMAL in that case.
 		 */
-		if (val == MAX77802_STATUS_OFF)
-			max77802->opmode[id] = MAX77802_OPMODE_NORMAL;
-		else
-			max77802->opmode[id] = val;
+		if (id < ARRAY_SIZE(max77802->opmode)) {
+			if (val == MAX77802_STATUS_OFF)
+				max77802->opmode[id] = MAX77802_OPMODE_NORMAL;
+			else
+				max77802->opmode[id] = val;
+		}
 
 		rdev = devm_regulator_register(&pdev->dev,
 					       &regulators[i], &config);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/mt6359-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/mt6359-regulator.c
@@ -951,9 +951,12 @@
 	struct regulator_config config = {};
 	struct regulator_dev *rdev;
 	struct mt6359_regulator_info *mt6359_info;
-	int i, hw_ver;
+	int i, hw_ver, ret;
+
+	ret = regmap_read(mt6397->regmap, MT6359P_HWCID, &hw_ver);
+	if (ret)
+		return ret;
 
-	regmap_read(mt6397->regmap, MT6359P_HWCID, &hw_ver);
 	if (hw_ver >= MT6359P_CHIP_VER)
 		mt6359_info = mt6359p_regulators;
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/mt6360-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/mt6360-regulator.c
@@ -319,15 +319,15 @@
 	}
 }
 
-#define MT6360_REGULATOR_DESC(_name, _sname, ereg, emask, vreg,	vmask,	\
-			      mreg, mmask, streg, stmask, vranges,	\
-			      vcnts, offon_delay, irq_tbls)		\
+#define MT6360_REGULATOR_DESC(match, _name, _sname, ereg, emask, vreg,	\
+			      vmask, mreg, mmask, streg, stmask,	\
+			      vranges, vcnts, offon_delay, irq_tbls)	\
 {									\
 	.desc = {							\
 		.name = #_name,						\
 		.supply_name = #_sname,					\
 		.id =  MT6360_REGULATOR_##_name,			\
-		.of_match = of_match_ptr(#_name),			\
+		.of_match = of_match_ptr(match),			\
 		.regulators_node = of_match_ptr("regulator"),		\
 		.of_map_mode = mt6360_regulator_of_map_mode,		\
 		.owner = THIS_MODULE,					\
@@ -351,21 +351,29 @@
 }
 
 static const struct mt6360_regulator_desc mt6360_regulator_descs[] =  {
-	MT6360_REGULATOR_DESC(BUCK1, BUCK1_VIN, 0x117, 0x40, 0x110, 0xff, 0x117, 0x30, 0x117, 0x04,
+	MT6360_REGULATOR_DESC("buck1", BUCK1, BUCK1_VIN,
+			      0x117, 0x40, 0x110, 0xff, 0x117, 0x30, 0x117, 0x04,
 			      buck_vout_ranges, 256, 0, buck1_irq_tbls),
-	MT6360_REGULATOR_DESC(BUCK2, BUCK2_VIN, 0x127, 0x40, 0x120, 0xff, 0x127, 0x30, 0x127, 0x04,
+	MT6360_REGULATOR_DESC("buck2", BUCK2, BUCK2_VIN,
+			      0x127, 0x40, 0x120, 0xff, 0x127, 0x30, 0x127, 0x04,
 			      buck_vout_ranges, 256, 0, buck2_irq_tbls),
-	MT6360_REGULATOR_DESC(LDO6, LDO_VIN3, 0x137, 0x40, 0x13B, 0xff, 0x137, 0x30, 0x137, 0x04,
+	MT6360_REGULATOR_DESC("ldo6", LDO6, LDO_VIN3,
+			      0x137, 0x40, 0x13B, 0xff, 0x137, 0x30, 0x137, 0x04,
 			      ldo_vout_ranges1, 256, 0, ldo6_irq_tbls),
-	MT6360_REGULATOR_DESC(LDO7, LDO_VIN3, 0x131, 0x40, 0x135, 0xff, 0x131, 0x30, 0x131, 0x04,
+	MT6360_REGULATOR_DESC("ldo7", LDO7, LDO_VIN3,
+			      0x131, 0x40, 0x135, 0xff, 0x131, 0x30, 0x131, 0x04,
 			      ldo_vout_ranges1, 256, 0, ldo7_irq_tbls),
-	MT6360_REGULATOR_DESC(LDO1, LDO_VIN1, 0x217, 0x40, 0x21B, 0xff, 0x217, 0x30, 0x217, 0x04,
+	MT6360_REGULATOR_DESC("ldo1", LDO1, LDO_VIN1,
+			      0x217, 0x40, 0x21B, 0xff, 0x217, 0x30, 0x217, 0x04,
 			      ldo_vout_ranges2, 256, 0, ldo1_irq_tbls),
-	MT6360_REGULATOR_DESC(LDO2, LDO_VIN1, 0x211, 0x40, 0x215, 0xff, 0x211, 0x30, 0x211, 0x04,
+	MT6360_REGULATOR_DESC("ldo2", LDO2, LDO_VIN1,
+			      0x211, 0x40, 0x215, 0xff, 0x211, 0x30, 0x211, 0x04,
 			      ldo_vout_ranges2, 256, 0, ldo2_irq_tbls),
-	MT6360_REGULATOR_DESC(LDO3, LDO_VIN1, 0x205, 0x40, 0x209, 0xff, 0x205, 0x30, 0x205, 0x04,
+	MT6360_REGULATOR_DESC("ldo3", LDO3, LDO_VIN1,
+			      0x205, 0x40, 0x209, 0xff, 0x205, 0x30, 0x205, 0x04,
 			      ldo_vout_ranges2, 256, 100, ldo3_irq_tbls),
-	MT6360_REGULATOR_DESC(LDO5, LDO_VIN2, 0x20B, 0x40, 0x20F, 0x7f, 0x20B, 0x30, 0x20B, 0x04,
+	MT6360_REGULATOR_DESC("ldo5", LDO5, LDO_VIN2,
+			      0x20B, 0x40, 0x20F, 0x7f, 0x20B, 0x30, 0x20B, 0x04,
 			      ldo_vout_ranges3, 128, 100, ldo5_irq_tbls),
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/of_regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/of_regulator.c
@@ -264,8 +264,12 @@
 		}
 
 		suspend_np = of_get_child_by_name(np, regulator_states[i]);
-		if (!suspend_np || !suspend_state)
+		if (!suspend_np)
 			continue;
+		if (!suspend_state) {
+			of_node_put(suspend_np);
+			continue;
+		}
 
 		if (!of_property_read_u32(suspend_np, "regulator-mode",
 					  &pval)) {
@@ -431,7 +435,7 @@
 					"failed to parse DT for regulator %pOFn\n",
 					child);
 				of_node_put(child);
-				return -EINVAL;
+				goto err_put;
 			}
 			match->of_node = of_node_get(child);
 			count++;
@@ -440,6 +444,18 @@
 	}
 
 	return count;
+
+err_put:
+	for (i = 0; i < num_matches; i++) {
+		struct of_regulator_match *match = &matches[i];
+
+		match->init_data = NULL;
+		if (match->of_node) {
+			of_node_put(match->of_node);
+			match->of_node = NULL;
+		}
+	}
+	return -EINVAL;
 }
 EXPORT_SYMBOL_GPL(of_regulator_match);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/pca9450-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/pca9450-regulator.c
@@ -256,7 +256,7 @@
 			.vsel_reg = PCA9450_REG_BUCK2OUT_DVS0,
 			.vsel_mask = BUCK2OUT_DVS0_MASK,
 			.enable_reg = PCA9450_REG_BUCK2CTRL,
-			.enable_mask = BUCK1_ENMODE_MASK,
+			.enable_mask = BUCK2_ENMODE_MASK,
 			.ramp_reg = PCA9450_REG_BUCK2CTRL,
 			.ramp_mask = BUCK2_RAMP_MASK,
 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
@@ -494,7 +494,7 @@
 			.vsel_reg = PCA9450_REG_BUCK2OUT_DVS0,
 			.vsel_mask = BUCK2OUT_DVS0_MASK,
 			.enable_reg = PCA9450_REG_BUCK2CTRL,
-			.enable_mask = BUCK1_ENMODE_MASK,
+			.enable_mask = BUCK2_ENMODE_MASK,
 			.ramp_reg = PCA9450_REG_BUCK2CTRL,
 			.ramp_mask = BUCK2_RAMP_MASK,
 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/pfuze100-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/pfuze100-regulator.c
@@ -521,6 +521,7 @@
 	parent = of_get_child_by_name(np, "regulators");
 	if (!parent) {
 		dev_err(dev, "regulators node not found\n");
+		of_node_put(np);
 		return -EINVAL;
 	}
 
@@ -550,6 +551,7 @@
 	}
 
 	of_node_put(parent);
+	of_node_put(np);
 	if (ret < 0) {
 		dev_err(dev, "Error parsing regulator init data: %d\n",
 			ret);
@@ -761,7 +763,7 @@
 		((pfuze_chip->chip_id == PFUZE3000) ? "3000" : "3001"))));
 
 	memcpy(pfuze_chip->regulator_descs, pfuze_chip->pfuze_regulators,
-		sizeof(pfuze_chip->regulator_descs));
+		regulator_num * sizeof(struct pfuze_regulator));
 
 	ret = pfuze_parse_regulators_dt(pfuze_chip);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/pwm-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/pwm-regulator.c
@@ -158,6 +158,9 @@
 	pwm_get_state(drvdata->pwm, &pstate);
 
 	voltage = pwm_get_relative_duty_cycle(&pstate, duty_unit);
+	if (voltage < min(max_uV_duty, min_uV_duty) ||
+	    voltage > max(max_uV_duty, min_uV_duty))
+		return -ENOTRECOVERABLE;
 
 	/*
 	 * The dutycycle for min_uV might be greater than the one for max_uV.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/qcom-labibb-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/qcom-labibb-regulator.c
@@ -260,7 +260,7 @@
 
 	/* If the regulator is not enabled, this is a fake event */
 	if (!ops->is_enabled(vreg->rdev))
-		return 0;
+		return IRQ_HANDLED;
 
 	/* If we tried to recover for too many times it's not getting better */
 	if (vreg->ocp_irq_count > LABIBB_MAX_OCP_COUNT)
@@ -822,6 +822,7 @@
 			if (irq == 0)
 				irq = -EINVAL;
 
+			of_node_put(reg_node);
 			return dev_err_probe(vreg->dev, irq,
 					     "Short-circuit irq not found.\n");
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/qcom-rpmh-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/qcom-rpmh-regulator.c
@@ -1108,7 +1108,7 @@
 static const struct rpmh_vreg_init_data pmr735a_vreg_data[] = {
 	RPMH_VREG("smps1",  "smp%s1",  &pmic5_ftsmps520, "vdd-s1"),
 	RPMH_VREG("smps2",  "smp%s2",  &pmic5_ftsmps520, "vdd-s2"),
-	RPMH_VREG("smps3",  "smp%s3",  &pmic5_hfsmps510, "vdd-s3"),
+	RPMH_VREG("smps3",  "smp%s3",  &pmic5_hfsmps515, "vdd-s3"),
 	RPMH_VREG("ldo1",   "ldo%s1",  &pmic5_nldo,      "vdd-l1-l2"),
 	RPMH_VREG("ldo2",   "ldo%s2",  &pmic5_nldo,      "vdd-l1-l2"),
 	RPMH_VREG("ldo3",   "ldo%s3",  &pmic5_nldo,      "vdd-l3"),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/qcom_rpm-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/qcom_rpm-regulator.c
@@ -802,6 +802,12 @@
 };
 
 static const struct rpm_regulator_data rpm_pm8058_regulators[] = {
+	{ "s0",   QCOM_RPM_PM8058_SMPS0,  &pm8058_smps, "vdd_s0" },
+	{ "s1",   QCOM_RPM_PM8058_SMPS1,  &pm8058_smps, "vdd_s1" },
+	{ "s2",   QCOM_RPM_PM8058_SMPS2,  &pm8058_smps, "vdd_s2" },
+	{ "s3",   QCOM_RPM_PM8058_SMPS3,  &pm8058_smps, "vdd_s3" },
+	{ "s4",   QCOM_RPM_PM8058_SMPS4,  &pm8058_smps, "vdd_s4" },
+
 	{ "l0",   QCOM_RPM_PM8058_LDO0,   &pm8058_nldo, "vdd_l0_l1_lvs"	},
 	{ "l1",   QCOM_RPM_PM8058_LDO1,   &pm8058_nldo, "vdd_l0_l1_lvs" },
 	{ "l2",   QCOM_RPM_PM8058_LDO2,   &pm8058_pldo, "vdd_l2_l11_l12" },
@@ -829,12 +835,6 @@
 	{ "l24",  QCOM_RPM_PM8058_LDO24,  &pm8058_nldo, "vdd_l23_l24_l25" },
 	{ "l25",  QCOM_RPM_PM8058_LDO25,  &pm8058_nldo, "vdd_l23_l24_l25" },
 
-	{ "s0",   QCOM_RPM_PM8058_SMPS0,  &pm8058_smps, "vdd_s0" },
-	{ "s1",   QCOM_RPM_PM8058_SMPS1,  &pm8058_smps, "vdd_s1" },
-	{ "s2",   QCOM_RPM_PM8058_SMPS2,  &pm8058_smps, "vdd_s2" },
-	{ "s3",   QCOM_RPM_PM8058_SMPS3,  &pm8058_smps, "vdd_s3" },
-	{ "s4",   QCOM_RPM_PM8058_SMPS4,  &pm8058_smps, "vdd_s4" },
-
 	{ "lvs0", QCOM_RPM_PM8058_LVS0, &pm8058_switch, "vdd_l0_l1_lvs" },
 	{ "lvs1", QCOM_RPM_PM8058_LVS1, &pm8058_switch, "vdd_l0_l1_lvs" },
 
@@ -843,6 +843,12 @@
 };
 
 static const struct rpm_regulator_data rpm_pm8901_regulators[] = {
+	{ "s0",   QCOM_RPM_PM8901_SMPS0, &pm8901_ftsmps, "vdd_s0" },
+	{ "s1",   QCOM_RPM_PM8901_SMPS1, &pm8901_ftsmps, "vdd_s1" },
+	{ "s2",   QCOM_RPM_PM8901_SMPS2, &pm8901_ftsmps, "vdd_s2" },
+	{ "s3",   QCOM_RPM_PM8901_SMPS3, &pm8901_ftsmps, "vdd_s3" },
+	{ "s4",   QCOM_RPM_PM8901_SMPS4, &pm8901_ftsmps, "vdd_s4" },
+
 	{ "l0",   QCOM_RPM_PM8901_LDO0, &pm8901_nldo, "vdd_l0" },
 	{ "l1",   QCOM_RPM_PM8901_LDO1, &pm8901_pldo, "vdd_l1" },
 	{ "l2",   QCOM_RPM_PM8901_LDO2, &pm8901_pldo, "vdd_l2" },
@@ -851,12 +857,6 @@
 	{ "l5",   QCOM_RPM_PM8901_LDO5, &pm8901_pldo, "vdd_l5" },
 	{ "l6",   QCOM_RPM_PM8901_LDO6, &pm8901_pldo, "vdd_l6" },
 
-	{ "s0",   QCOM_RPM_PM8901_SMPS0, &pm8901_ftsmps, "vdd_s0" },
-	{ "s1",   QCOM_RPM_PM8901_SMPS1, &pm8901_ftsmps, "vdd_s1" },
-	{ "s2",   QCOM_RPM_PM8901_SMPS2, &pm8901_ftsmps, "vdd_s2" },
-	{ "s3",   QCOM_RPM_PM8901_SMPS3, &pm8901_ftsmps, "vdd_s3" },
-	{ "s4",   QCOM_RPM_PM8901_SMPS4, &pm8901_ftsmps, "vdd_s4" },
-
 	{ "lvs0", QCOM_RPM_PM8901_LVS0, &pm8901_switch, "lvs0_in" },
 	{ "lvs1", QCOM_RPM_PM8901_LVS1, &pm8901_switch, "lvs1_in" },
 	{ "lvs2", QCOM_RPM_PM8901_LVS2, &pm8901_switch, "lvs2_in" },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/qcom_smd-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/qcom_smd-regulator.c
@@ -9,6 +9,7 @@
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
 #include <linux/soc/qcom/smd-rpm.h>
 
 struct qcom_rpm_reg {
@@ -356,10 +357,10 @@
 
 static const struct regulator_desc pm8916_pldo = {
 	.linear_ranges = (struct linear_range[]) {
-		REGULATOR_LINEAR_RANGE(750000, 0, 208, 12500),
+		REGULATOR_LINEAR_RANGE(1750000, 0, 127, 12500),
 	},
 	.n_linear_ranges = 1,
-	.n_voltages = 209,
+	.n_voltages = 128,
 	.ops = &rpm_smps_ldo_ops,
 };
 
@@ -925,32 +926,31 @@
 	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8950_hfsmps, "vdd_s2" },
 	{ "s3", QCOM_SMD_RPM_SMPA, 3, &pm8950_hfsmps, "vdd_s3" },
 	{ "s4", QCOM_SMD_RPM_SMPA, 4, &pm8950_hfsmps, "vdd_s4" },
-	{ "s5", QCOM_SMD_RPM_SMPA, 5, &pm8950_ftsmps2p5, "vdd_s5" },
+	/* S5 is managed via SPMI. */
 	{ "s6", QCOM_SMD_RPM_SMPA, 6, &pm8950_hfsmps, "vdd_s6" },
 
 	{ "l1", QCOM_SMD_RPM_LDOA, 1, &pm8950_ult_nldo, "vdd_l1_l19" },
 	{ "l2", QCOM_SMD_RPM_LDOA, 2, &pm8950_ult_nldo, "vdd_l2_l23" },
 	{ "l3", QCOM_SMD_RPM_LDOA, 3, &pm8950_ult_nldo, "vdd_l3" },
-	{ "l4", QCOM_SMD_RPM_LDOA, 4, &pm8950_ult_pldo, "vdd_l4_l5_l6_l7_l16" },
-	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pm8950_pldo_lv, "vdd_l4_l5_l6_l7_l16" },
-	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pm8950_pldo_lv, "vdd_l4_l5_l6_l7_l16" },
-	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pm8950_pldo_lv, "vdd_l4_l5_l6_l7_l16" },
+	/* L4 seems not to exist. */
+	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pm8950_pldo_lv, "vdd_l5_l6_l7_l16" },
+	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pm8950_pldo_lv, "vdd_l5_l6_l7_l16" },
+	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pm8950_pldo_lv, "vdd_l5_l6_l7_l16" },
 	{ "l8", QCOM_SMD_RPM_LDOA, 8, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
 	{ "l9", QCOM_SMD_RPM_LDOA, 9, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
 	{ "l10", QCOM_SMD_RPM_LDOA, 10, &pm8950_ult_nldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l16", QCOM_SMD_RPM_LDOA, 16, &pm8950_ult_pldo, "vdd_l4_l5_l6_l7_l16"},
-	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l18", QCOM_SMD_RPM_LDOA, 18, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l19", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l1_l19"},
-	{ "l20", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l20"},
-	{ "l21", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l21"},
-	{ "l22", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l23", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l2_l23"},
+	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
+	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
+	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
+	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
+	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
+	{ "l16", QCOM_SMD_RPM_LDOA, 16, &pm8950_ult_pldo, "vdd_l5_l6_l7_l16" },
+	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
+	/* L18 seems not to exist. */
+	{ "l19", QCOM_SMD_RPM_LDOA, 19, &pm8950_pldo, "vdd_l1_l19" },
+	/* L20 & L21 seem not to exist. */
+	{ "l22", QCOM_SMD_RPM_LDOA, 22, &pm8950_pldo, "vdd_l8_l11_l12_l17_l22" },
+	{ "l23", QCOM_SMD_RPM_LDOA, 23, &pm8950_pldo, "vdd_l2_l23" },
 	{}
 };
 
@@ -1190,52 +1190,93 @@
 };
 MODULE_DEVICE_TABLE(of, rpm_of_match);
 
-static int rpm_reg_probe(struct platform_device *pdev)
+/**
+ * rpm_regulator_init_vreg() - initialize all attributes of a qcom_smd-regulator
+ * @vreg:		Pointer to the individual qcom_smd-regulator resource
+ * @dev:		Pointer to the top level qcom_smd-regulator PMIC device
+ * @node:		Pointer to the individual qcom_smd-regulator resource
+ *			device node
+ * @rpm:		Pointer to the rpm bus node
+ * @pmic_rpm_data:	Pointer to a null-terminated array of qcom_smd-regulator
+ *			resources defined for the top level PMIC device
+ *
+ * Return: 0 on success, errno on failure
+ */
+static int rpm_regulator_init_vreg(struct qcom_rpm_reg *vreg, struct device *dev,
+				   struct device_node *node, struct qcom_smd_rpm *rpm,
+				   const struct rpm_regulator_data *pmic_rpm_data)
 {
-	const struct rpm_regulator_data *reg;
-	const struct of_device_id *match;
-	struct regulator_config config = { };
+	struct regulator_config config = {};
+	const struct rpm_regulator_data *rpm_data;
 	struct regulator_dev *rdev;
+	int ret;
+
+	for (rpm_data = pmic_rpm_data; rpm_data->name; rpm_data++)
+		if (of_node_name_eq(node, rpm_data->name))
+			break;
+
+	if (!rpm_data->name) {
+		dev_err(dev, "Unknown regulator %pOFn\n", node);
+		return -EINVAL;
+	}
+
+	vreg->dev	= dev;
+	vreg->rpm	= rpm;
+	vreg->type	= rpm_data->type;
+	vreg->id	= rpm_data->id;
+
+	memcpy(&vreg->desc, rpm_data->desc, sizeof(vreg->desc));
+	vreg->desc.name = rpm_data->name;
+	vreg->desc.supply_name = rpm_data->supply;
+	vreg->desc.owner = THIS_MODULE;
+	vreg->desc.type = REGULATOR_VOLTAGE;
+	vreg->desc.of_match = rpm_data->name;
+
+	config.dev		= dev;
+	config.of_node		= node;
+	config.driver_data	= vreg;
+
+	rdev = devm_regulator_register(dev, &vreg->desc, &config);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(dev, "%pOFn: devm_regulator_register() failed, ret=%d\n", node, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rpm_reg_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct rpm_regulator_data *vreg_data;
+	struct device_node *node;
 	struct qcom_rpm_reg *vreg;
 	struct qcom_smd_rpm *rpm;
+	int ret;
 
 	rpm = dev_get_drvdata(pdev->dev.parent);
 	if (!rpm) {
-		dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
+		dev_err(&pdev->dev, "Unable to retrieve handle to rpm\n");
 		return -ENODEV;
 	}
 
-	match = of_match_device(rpm_of_match, &pdev->dev);
-	if (!match) {
-		dev_err(&pdev->dev, "failed to match device\n");
+	vreg_data = of_device_get_match_data(dev);
+	if (!vreg_data)
 		return -ENODEV;
-	}
 
-	for (reg = match->data; reg->name; reg++) {
+	for_each_available_child_of_node(dev->of_node, node) {
 		vreg = devm_kzalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
-		if (!vreg)
+		if (!vreg) {
+			of_node_put(node);
 			return -ENOMEM;
+		}
+
+		ret = rpm_regulator_init_vreg(vreg, dev, node, rpm, vreg_data);
 
-		vreg->dev = &pdev->dev;
-		vreg->type = reg->type;
-		vreg->id = reg->id;
-		vreg->rpm = rpm;
-
-		memcpy(&vreg->desc, reg->desc, sizeof(vreg->desc));
-
-		vreg->desc.id = -1;
-		vreg->desc.owner = THIS_MODULE;
-		vreg->desc.type = REGULATOR_VOLTAGE;
-		vreg->desc.name = reg->name;
-		vreg->desc.supply_name = reg->supply;
-		vreg->desc.of_match = reg->name;
-
-		config.dev = &pdev->dev;
-		config.driver_data = vreg;
-		rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config);
-		if (IS_ERR(rdev)) {
-			dev_err(&pdev->dev, "failed to register %s\n", reg->name);
-			return PTR_ERR(rdev);
+		if (ret < 0) {
+			of_node_put(node);
+			return ret;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/rk808-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/rk808-regulator.c
@@ -906,6 +906,8 @@
 		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
 		.vsel_reg = RK817_BUCK3_ON_VSEL_REG,
 		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.apply_reg = RK817_POWER_CONFIG,
+		.apply_bit = RK817_BUCK3_FB_RES_INTER,
 		.enable_reg = RK817_POWER_EN_REG(0),
 		.enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
 		.enable_val = ENABLE_MASK(RK817_ID_DCDC3),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/rpi-panel-attiny-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/rpi-panel-attiny-regulator.c
@@ -37,11 +37,24 @@
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
 	unsigned int data;
+	int ret, i;
 
 	regmap_write(rdev->regmap, REG_POWERON, 1);
+	msleep(80);
+
 	/* Wait for nPWRDWN to go low to indicate poweron is done. */
-	regmap_read_poll_timeout(rdev->regmap, REG_PORTB, data,
-					data & BIT(0), 10, 1000000);
+	for (i = 0; i < 20; i++) {
+		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		if (!ret) {
+			if (data & BIT(0))
+				break;
+		}
+		usleep_range(10000, 12000);
+	}
+	usleep_range(10000, 12000);
+
+	if (ret)
+		pr_err("%s: regmap_read_poll_timeout failed %d\n", __func__, ret);
 
 	/* Default to the same orientation as the closed source
 	 * firmware used for the panel.  Runtime rotation
@@ -57,23 +70,34 @@
 {
 	regmap_write(rdev->regmap, REG_PWM, 0);
 	regmap_write(rdev->regmap, REG_POWERON, 0);
-	udelay(1);
+	msleep(30);
 	return 0;
 }
 
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
 	unsigned int data;
-	int ret;
+	int ret, i;
 
-	ret = regmap_read(rdev->regmap, REG_POWERON, &data);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(rdev->regmap, REG_POWERON, &data);
+		if (!ret)
+			break;
+		usleep_range(10000, 12000);
+	}
 	if (ret < 0)
 		return ret;
 
 	if (!(data & BIT(0)))
 		return 0;
 
-	ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		if (!ret)
+			break;
+		usleep_range(10000, 12000);
+	}
+
 	if (ret < 0)
 		return ret;
 
@@ -103,20 +127,32 @@
 {
 	struct regmap *regmap = bl_get_data(bl);
 	int brightness = bl->props.brightness;
+	int ret, i;
 
 	if (bl->props.power != FB_BLANK_UNBLANK ||
 	    bl->props.fb_blank != FB_BLANK_UNBLANK)
 		brightness = 0;
 
-	return regmap_write(regmap, REG_PWM, brightness);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_write(regmap, REG_PWM, brightness);
+		if (!ret)
+			break;
+	}
+
+	return ret;
 }
 
 static int attiny_get_brightness(struct backlight_device *bl)
 {
 	struct regmap *regmap = bl_get_data(bl);
-	int ret, brightness;
+	int ret, brightness, i;
+
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(regmap, REG_PWM, &brightness);
+		if (!ret)
+			break;
+	}
 
-	ret = regmap_read(regmap, REG_PWM, &brightness);
 	if (ret)
 		return ret;
 
@@ -166,7 +202,7 @@
 	}
 
 	regmap_write(regmap, REG_POWERON, 0);
-	mdelay(1);
+	msleep(30);
 
 	config.dev = &i2c->dev;
 	config.regmap = regmap;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/rtq2134-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/rtq2134-regulator.c
@@ -285,6 +285,7 @@
 		.enable_mask = RTQ2134_VOUTEN_MASK, \
 		.active_discharge_reg = RTQ2134_REG_BUCK##_id##_CFG0, \
 		.active_discharge_mask = RTQ2134_ACTDISCHG_MASK, \
+		.active_discharge_on = RTQ2134_ACTDISCHG_MASK, \
 		.ramp_reg = RTQ2134_REG_BUCK##_id##_RSPCFG, \
 		.ramp_mask = RTQ2134_RSPUP_MASK, \
 		.ramp_delay_table = rtq2134_buck_ramp_delay_table, \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/s5m8767.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/s5m8767.c
@@ -850,18 +850,15 @@
 	/* DS4 GPIO */
 	gpio_direction_output(pdata->buck_ds[2], 0x0);
 
-	if (pdata->buck2_gpiodvs || pdata->buck3_gpiodvs ||
-	   pdata->buck4_gpiodvs) {
-		regmap_update_bits(s5m8767->iodev->regmap_pmic,
-				S5M8767_REG_BUCK2CTRL, 1 << 1,
-				(pdata->buck2_gpiodvs) ? (1 << 1) : (0 << 1));
-		regmap_update_bits(s5m8767->iodev->regmap_pmic,
-				S5M8767_REG_BUCK3CTRL, 1 << 1,
-				(pdata->buck3_gpiodvs) ? (1 << 1) : (0 << 1));
-		regmap_update_bits(s5m8767->iodev->regmap_pmic,
-				S5M8767_REG_BUCK4CTRL, 1 << 1,
-				(pdata->buck4_gpiodvs) ? (1 << 1) : (0 << 1));
-	}
+	regmap_update_bits(s5m8767->iodev->regmap_pmic,
+			   S5M8767_REG_BUCK2CTRL, 1 << 1,
+			   (pdata->buck2_gpiodvs) ? (1 << 1) : (0 << 1));
+	regmap_update_bits(s5m8767->iodev->regmap_pmic,
+			   S5M8767_REG_BUCK3CTRL, 1 << 1,
+			   (pdata->buck3_gpiodvs) ? (1 << 1) : (0 << 1));
+	regmap_update_bits(s5m8767->iodev->regmap_pmic,
+			   S5M8767_REG_BUCK4CTRL, 1 << 1,
+			   (pdata->buck4_gpiodvs) ? (1 << 1) : (0 << 1));
 
 	/* Initialize GPIO DVS registers */
 	for (i = 0; i < 8; i++) {
@@ -926,10 +923,14 @@
 
 	for (i = 0; i < pdata->num_regulators; i++) {
 		const struct sec_voltage_desc *desc;
-		int id = pdata->regulators[i].id;
+		unsigned int id = pdata->regulators[i].id;
 		int enable_reg, enable_val;
 		struct regulator_dev *rdev;
 
+		BUILD_BUG_ON(ARRAY_SIZE(regulators) != ARRAY_SIZE(reg_voltage_map));
+		if (WARN_ON_ONCE(id >= ARRAY_SIZE(regulators)))
+			continue;
+
 		desc = reg_voltage_map[id];
 		if (desc) {
 			regulators[id].n_voltages =
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/scmi-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/scmi-regulator.c
@@ -352,7 +352,7 @@
 			return ret;
 		}
 	}
-
+	of_node_put(np);
 	/*
 	 * Register a regulator for each valid regulator-DT-entry that we
 	 * can successfully reach via SCMI and has a valid associated voltage
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/slg51000-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/slg51000-regulator.c
@@ -457,6 +457,8 @@
 		chip->cs_gpiod = cs_gpiod;
 	}
 
+	usleep_range(10000, 11000);
+
 	i2c_set_clientdata(client, chip);
 	chip->chip_irq = client->irq;
 	chip->dev = dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/stm32-pwr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/stm32-pwr.c
@@ -129,17 +129,16 @@
 
 static int stm32_pwr_regulator_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
 	struct stm32_pwr_reg *priv;
 	void __iomem *base;
 	struct regulator_dev *rdev;
 	struct regulator_config config = { };
 	int i, ret = 0;
 
-	base = of_iomap(np, 0);
-	if (!base) {
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base)) {
 		dev_err(&pdev->dev, "Unable to map IO memory\n");
-		return -ENOMEM;
+		return PTR_ERR(base);
 	}
 
 	config.dev = &pdev->dev;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/twl6030-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/twl6030-regulator.c
@@ -67,6 +67,7 @@
 #define TWL6030_CFG_STATE_SLEEP	0x03
 #define TWL6030_CFG_STATE_GRP_SHIFT	5
 #define TWL6030_CFG_STATE_APP_SHIFT	2
+#define TWL6030_CFG_STATE_MASK		0x03
 #define TWL6030_CFG_STATE_APP_MASK	(0x03 << TWL6030_CFG_STATE_APP_SHIFT)
 #define TWL6030_CFG_STATE_APP(v)	(((v) & TWL6030_CFG_STATE_APP_MASK) >>\
 						TWL6030_CFG_STATE_APP_SHIFT)
@@ -128,13 +129,14 @@
 		if (grp < 0)
 			return grp;
 		grp &= P1_GRP_6030;
+		val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE);
+		val = TWL6030_CFG_STATE_APP(val);
 	} else {
+		val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE);
+		val &= TWL6030_CFG_STATE_MASK;
 		grp = 1;
 	}
 
-	val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE);
-	val = TWL6030_CFG_STATE_APP(val);
-
 	return grp && (val == TWL6030_CFG_STATE_ON);
 }
 
@@ -187,7 +189,12 @@
 
 	val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE);
 
-	switch (TWL6030_CFG_STATE_APP(val)) {
+	if (info->features & TWL6032_SUBCLASS)
+		val &= TWL6030_CFG_STATE_MASK;
+	else
+		val = TWL6030_CFG_STATE_APP(val);
+
+	switch (val) {
 	case TWL6030_CFG_STATE_ON:
 		return REGULATOR_STATUS_NORMAL;
 
@@ -530,6 +537,7 @@
 #define TWL6032_ADJUSTABLE_LDO(label, offset) \
 static const struct twlreg_info TWL6032_INFO_##label = { \
 	.base = offset, \
+	.features = TWL6032_SUBCLASS, \
 	.desc = { \
 		.name = #label, \
 		.id = TWL6032_REG_##label, \
@@ -562,6 +570,7 @@
 #define TWL6032_ADJUSTABLE_SMPS(label, offset) \
 static const struct twlreg_info TWLSMPS_INFO_##label = { \
 	.base = offset, \
+	.features = TWL6032_SUBCLASS, \
 	.desc = { \
 		.name = #label, \
 		.id = TWL6032_REG_##label, \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/vqmmc-ipq4019-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/vqmmc-ipq4019-regulator.c
@@ -86,6 +86,7 @@
 	{ .compatible = "qcom,vqmmc-ipq4019-regulator", },
 	{},
 };
+MODULE_DEVICE_TABLE(of, regulator_ipq4019_of_match);
 
 static struct platform_driver ipq4019_regulator_driver = {
 	.probe = ipq4019_regulator_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/regulator/wm8994-regulator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/regulator/wm8994-regulator.c
@@ -82,6 +82,35 @@
 		.min_uV = 2400000,
 		.uV_step = 100000,
 		.enable_time = 3000,
+		.off_on_delay = 36000,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "LDO2",
+		.id = 2,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = WM8994_LDO2_MAX_SELECTOR + 1,
+		.vsel_reg = WM8994_LDO_2,
+		.vsel_mask = WM8994_LDO2_VSEL_MASK,
+		.ops = &wm8994_ldo2_ops,
+		.enable_time = 3000,
+		.off_on_delay = 36000,
+		.owner = THIS_MODULE,
+	},
+};
+
+static const struct regulator_desc wm8958_ldo_desc[] = {
+	{
+		.name = "LDO1",
+		.id = 1,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = WM8994_LDO1_MAX_SELECTOR + 1,
+		.vsel_reg = WM8994_LDO_1,
+		.vsel_mask = WM8994_LDO1_VSEL_MASK,
+		.ops = &wm8994_ldo1_ops,
+		.min_uV = 2400000,
+		.uV_step = 100000,
+		.enable_time = 3000,
 		.owner = THIS_MODULE,
 	},
 	{
@@ -172,9 +201,16 @@
 	 * regulator core and we need not worry about it on the
 	 * error path.
 	 */
-	ldo->regulator = devm_regulator_register(&pdev->dev,
-						 &wm8994_ldo_desc[id],
-						 &config);
+	if (ldo->wm8994->type == WM8994) {
+		ldo->regulator = devm_regulator_register(&pdev->dev,
+							 &wm8994_ldo_desc[id],
+							 &config);
+	} else {
+		ldo->regulator = devm_regulator_register(&pdev->dev,
+							 &wm8958_ldo_desc[id],
+							 &config);
+	}
+
 	if (IS_ERR(ldo->regulator)) {
 		ret = PTR_ERR(ldo->regulator);
 		dev_err(wm8994->dev, "Failed to register LDO%d: %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/Kconfig
@@ -271,12 +271,21 @@
 	  processor framework.
 	  This can be either built-in or a loadable module.
 
+config ZYNQ_REMOTEPROC
+	tristate "Support ZYNQ remoteproc"
+	depends on ARCH_ZYNQ && SMP && !DEBUG_SG && BL_SWITCHER
+	select RPMSG_VIRTIO
+	select SRAM
+	help
+	  Say y here to support Xilinx ZynQ remote processors (the second
+	  ARM CORTEX-A9 cpu) via the remote processor framework.
+
 config ST_SLIM_REMOTEPROC
 	tristate
 
 config STM32_RPROC
 	tristate "STM32 remoteproc support"
-	depends on ARCH_STM32
+	depends on ARCH_STM32 || COMPILE_TEST
 	depends on REMOTEPROC
 	select MAILBOX
 	help
@@ -315,6 +324,14 @@
 	  It's safe to say N here if you're not interested in utilizing
 	  a slave processor.
 
+config ZYNQMP_R5_REMOTEPROC
+	tristate "ZynqMP R5 remoteproc support"
+	depends on PM && ARCH_ZYNQMP
+	select RPMSG_VIRTIO
+	select ZYNQMP_IPI_MBOX
+	help
+	  Say y or m here to support ZynqMP R5 remote processors via the remote
+	  processor framework.
 endif # REMOTEPROC
 
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/Makefile
@@ -31,7 +31,9 @@
 qcom_wcnss_pil-y			+= qcom_wcnss.o
 qcom_wcnss_pil-y			+= qcom_wcnss_iris.o
 obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
+obj-$(CONFIG_ZYNQ_REMOTEPROC)		+= zynq_remoteproc.o
 obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
 obj-$(CONFIG_STM32_RPROC)		+= stm32_rproc.o
 obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o
 obj-$(CONFIG_TI_K3_R5_REMOTEPROC)	+= ti_k3_r5_remoteproc.o
+obj-$(CONFIG_ZYNQMP_R5_REMOTEPROC)	+= zynqmp_r5_remoteproc.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/imx_rproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/imx_rproc.c
@@ -71,6 +71,7 @@
 /* att flags */
 /* M4 own area. Can be mapped at probe */
 #define ATT_OWN		BIT(1)
+#define ATT_IOMEM	BIT(2)
 
 /* address translation table */
 struct imx_rproc_att {
@@ -117,7 +118,7 @@
 static const struct imx_rproc_att imx_rproc_att_imx8mn[] = {
 	/* dev addr , sys addr  , size	    , flags */
 	/* ITCM   */
-	{ 0x00000000, 0x007E0000, 0x00020000, ATT_OWN },
+	{ 0x00000000, 0x007E0000, 0x00020000, ATT_OWN | ATT_IOMEM },
 	/* OCRAM_S */
 	{ 0x00180000, 0x00180000, 0x00009000, 0 },
 	/* OCRAM */
@@ -131,7 +132,7 @@
 	/* DDR (Code) - alias */
 	{ 0x10000000, 0x40000000, 0x0FFE0000, 0 },
 	/* DTCM */
-	{ 0x20000000, 0x00800000, 0x00020000, ATT_OWN },
+	{ 0x20000000, 0x00800000, 0x00020000, ATT_OWN | ATT_IOMEM },
 	/* OCRAM_S - alias */
 	{ 0x20180000, 0x00180000, 0x00008000, ATT_OWN },
 	/* OCRAM */
@@ -147,7 +148,7 @@
 static const struct imx_rproc_att imx_rproc_att_imx8mq[] = {
 	/* dev addr , sys addr  , size	    , flags */
 	/* TCML - alias */
-	{ 0x00000000, 0x007e0000, 0x00020000, 0 },
+	{ 0x00000000, 0x007e0000, 0x00020000, ATT_IOMEM},
 	/* OCRAM_S */
 	{ 0x00180000, 0x00180000, 0x00008000, 0 },
 	/* OCRAM */
@@ -157,11 +158,11 @@
 	/* QSPI Code - alias */
 	{ 0x08000000, 0x08000000, 0x08000000, 0 },
 	/* DDR (Code) - alias */
-	{ 0x10000000, 0x80000000, 0x0FFE0000, 0 },
+	{ 0x10000000, 0x40000000, 0x0FFE0000, 0 },
 	/* TCML */
-	{ 0x1FFE0000, 0x007E0000, 0x00020000, ATT_OWN },
+	{ 0x1FFE0000, 0x007E0000, 0x00020000, ATT_OWN  | ATT_IOMEM},
 	/* TCMU */
-	{ 0x20000000, 0x00800000, 0x00020000, ATT_OWN },
+	{ 0x20000000, 0x00800000, 0x00020000, ATT_OWN  | ATT_IOMEM},
 	/* OCRAM_S */
 	{ 0x20180000, 0x00180000, 0x00008000, ATT_OWN },
 	/* OCRAM */
@@ -199,12 +200,12 @@
 	/* OCRAM_PXP (Code) - alias */
 	{ 0x00940000, 0x00940000, 0x00008000, 0 },
 	/* TCML (Code) */
-	{ 0x1FFF8000, 0x007F8000, 0x00008000, ATT_OWN },
+	{ 0x1FFF8000, 0x007F8000, 0x00008000, ATT_OWN | ATT_IOMEM },
 	/* DDR (Code) - alias, first part of DDR (Data) */
 	{ 0x10000000, 0x80000000, 0x0FFF0000, 0 },
 
 	/* TCMU (Data) */
-	{ 0x20000000, 0x00800000, 0x00008000, ATT_OWN },
+	{ 0x20000000, 0x00800000, 0x00008000, ATT_OWN | ATT_IOMEM },
 	/* OCRAM (Data) */
 	{ 0x20200000, 0x00900000, 0x00020000, 0 },
 	/* OCRAM_EPDC (Data) */
@@ -218,18 +219,18 @@
 static const struct imx_rproc_att imx_rproc_att_imx6sx[] = {
 	/* dev addr , sys addr  , size	    , flags */
 	/* TCML (M4 Boot Code) - alias */
-	{ 0x00000000, 0x007F8000, 0x00008000, 0 },
+	{ 0x00000000, 0x007F8000, 0x00008000, ATT_IOMEM },
 	/* OCRAM_S (Code) */
 	{ 0x00180000, 0x008F8000, 0x00004000, 0 },
 	/* OCRAM_S (Code) - alias */
 	{ 0x00180000, 0x008FC000, 0x00004000, 0 },
 	/* TCML (Code) */
-	{ 0x1FFF8000, 0x007F8000, 0x00008000, ATT_OWN },
+	{ 0x1FFF8000, 0x007F8000, 0x00008000, ATT_OWN | ATT_IOMEM },
 	/* DDR (Code) - alias, first part of DDR (Data) */
 	{ 0x10000000, 0x80000000, 0x0FFF8000, 0 },
 
 	/* TCMU (Data) */
-	{ 0x20000000, 0x00800000, 0x00008000, ATT_OWN },
+	{ 0x20000000, 0x00800000, 0x00008000, ATT_OWN | ATT_IOMEM },
 	/* OCRAM_S (Data) - alias? */
 	{ 0x208F8000, 0x008F8000, 0x00004000, 0 },
 	/* DDR (Data) */
@@ -341,7 +342,7 @@
 }
 
 static int imx_rproc_da_to_sys(struct imx_rproc *priv, u64 da,
-			       size_t len, u64 *sys)
+			       size_t len, u64 *sys, bool *is_iomem)
 {
 	const struct imx_rproc_dcfg *dcfg = priv->dcfg;
 	int i;
@@ -354,6 +355,8 @@
 			unsigned int offset = da - att->da;
 
 			*sys = att->sa + offset;
+			if (is_iomem)
+				*is_iomem = att->flags & ATT_IOMEM;
 			return 0;
 		}
 	}
@@ -377,7 +380,7 @@
 	 * On device side we have many aliases, so we need to convert device
 	 * address (M4) to system bus address first.
 	 */
-	if (imx_rproc_da_to_sys(priv, da, len, &sys))
+	if (imx_rproc_da_to_sys(priv, da, len, &sys, is_iomem))
 		return NULL;
 
 	for (i = 0; i < IMX_RPROC_MEM_MAX; i++) {
@@ -444,8 +447,12 @@
 		if (!strcmp(it.node->name, "vdev0buffer"))
 			continue;
 
+		if (!strcmp(it.node->name, "rsc-table"))
+			continue;
+
 		rmem = of_reserved_mem_lookup(it.node);
 		if (!rmem) {
+			of_node_put(it.node);
 			dev_err(priv->dev, "unable to acquire memory-region\n");
 			return -EINVAL;
 		}
@@ -458,10 +465,12 @@
 					   imx_rproc_mem_alloc, imx_rproc_mem_release,
 					   it.node->name);
 
-		if (mem)
+		if (mem) {
 			rproc_coredump_add_segment(rproc, da, rmem->size);
-		else
+		} else {
+			of_node_put(it.node);
 			return -ENOMEM;
+		}
 
 		rproc_add_carveout(rproc, mem);
 	}
@@ -520,6 +529,17 @@
 	return (struct resource_table *)priv->rsc_table;
 }
 
+static struct resource_table *
+imx_rproc_elf_find_loaded_rsc_table(struct rproc *rproc, const struct firmware *fw)
+{
+	struct imx_rproc *priv = rproc->priv;
+
+	if (priv->rsc_table)
+		return (struct resource_table *)priv->rsc_table;
+
+	return rproc_elf_find_loaded_rsc_table(rproc, fw);
+}
+
 static const struct rproc_ops imx_rproc_ops = {
 	.prepare	= imx_rproc_prepare,
 	.attach		= imx_rproc_attach,
@@ -529,7 +549,7 @@
 	.da_to_va       = imx_rproc_da_to_va,
 	.load		= rproc_elf_load_segments,
 	.parse_fw	= imx_rproc_parse_fw,
-	.find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
+	.find_loaded_rsc_table = imx_rproc_elf_find_loaded_rsc_table,
 	.get_loaded_rsc_table = imx_rproc_get_loaded_rsc_table,
 	.sanity_check	= rproc_elf_sanity_check,
 	.get_boot_addr	= rproc_elf_get_boot_addr,
@@ -553,8 +573,12 @@
 		if (b >= IMX_RPROC_MEM_MAX)
 			break;
 
-		priv->mem[b].cpu_addr = devm_ioremap(&pdev->dev,
-						     att->sa, att->size);
+		if (att->flags & ATT_IOMEM)
+			priv->mem[b].cpu_addr = devm_ioremap(&pdev->dev,
+							     att->sa, att->size);
+		else
+			priv->mem[b].cpu_addr = devm_ioremap_wc(&pdev->dev,
+								att->sa, att->size);
 		if (!priv->mem[b].cpu_addr) {
 			dev_err(dev, "failed to remap %#x bytes from %#x\n", att->size, att->sa);
 			return -ENOMEM;
@@ -575,30 +599,37 @@
 		struct resource res;
 
 		node = of_parse_phandle(np, "memory-region", a);
-		/* Not map vdev region */
-		if (!strcmp(node->name, "vdev"))
+		if (!node)
 			continue;
+		/* Not map vdevbuffer, vdevring region */
+		if (!strncmp(node->name, "vdev", strlen("vdev"))) {
+			of_node_put(node);
+			continue;
+		}
 		err = of_address_to_resource(node, 0, &res);
 		if (err) {
 			dev_err(dev, "unable to resolve memory region\n");
+			of_node_put(node);
 			return err;
 		}
 
-		of_node_put(node);
-
-		if (b >= IMX_RPROC_MEM_MAX)
+		if (b >= IMX_RPROC_MEM_MAX) {
+			of_node_put(node);
 			break;
+		}
 
 		/* Not use resource version, because we might share region */
 		priv->mem[b].cpu_addr = devm_ioremap(&pdev->dev, res.start, resource_size(&res));
 		if (!priv->mem[b].cpu_addr) {
 			dev_err(dev, "failed to remap %pr\n", &res);
+			of_node_put(node);
 			return -ENOMEM;
 		}
 		priv->mem[b].sys_addr = res.start;
 		priv->mem[b].size = resource_size(&res);
-		if (!strcmp(node->name, "rsc_table"))
+		if (!strcmp(node->name, "rsc-table"))
 			priv->rsc_table = priv->mem[b].cpu_addr;
+		of_node_put(node);
 		b++;
 	}
 
@@ -772,6 +803,8 @@
 		goto err_put_rproc;
 	}
 
+	INIT_WORK(&priv->rproc_work, imx_rproc_vq_work);
+
 	ret = imx_rproc_xtr_mbox_init(rproc);
 	if (ret)
 		goto err_put_wkq;
@@ -790,8 +823,6 @@
 	if (ret)
 		goto err_put_mbox;
 
-	INIT_WORK(&priv->rproc_work, imx_rproc_vq_work);
-
 	if (rproc->state != RPROC_DETACHED)
 		rproc->auto_boot = of_property_read_bool(np, "fsl,auto-boot");
 
@@ -823,6 +854,7 @@
 	clk_disable_unprepare(priv->clk);
 	rproc_del(rproc);
 	imx_rproc_free_mbox(rproc);
+	destroy_workqueue(priv->workqueue);
 	rproc_free(rproc);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/mtk_scp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/mtk_scp.c
@@ -126,7 +126,7 @@
 static int scp_ipi_init(struct mtk_scp *scp, const struct firmware *fw)
 {
 	int ret;
-	size_t offset;
+	size_t buf_sz, offset;
 
 	/* read the ipi buf addr from FW itself first */
 	ret = scp_elf_read_ipi_buf_addr(scp, fw, &offset);
@@ -138,6 +138,14 @@
 	}
 	dev_info(scp->dev, "IPI buf addr %#010zx\n", offset);
 
+	/* Make sure IPI buffer fits in the L2TCM range assigned to this core */
+	buf_sz = sizeof(*scp->recv_buf) + sizeof(*scp->send_buf);
+
+	if (scp->sram_size < buf_sz + offset) {
+		dev_err(scp->dev, "IPI buffer does not fit in SRAM.\n");
+		return -EOVERFLOW;
+	}
+
 	scp->recv_buf = (struct mtk_share_obj __iomem *)
 			(scp->sram_base + offset);
 	scp->send_buf = (struct mtk_share_obj __iomem *)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/mtk_scp_ipi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/mtk_scp_ipi.c
@@ -164,21 +164,21 @@
 	    WARN_ON(len > sizeof(send_obj->share_buf)) || WARN_ON(!buf))
 		return -EINVAL;
 
-	mutex_lock(&scp->send_lock);
-
 	ret = clk_prepare_enable(scp->clk);
 	if (ret) {
 		dev_err(scp->dev, "failed to enable clock\n");
-		goto unlock_mutex;
+		return ret;
 	}
 
+	mutex_lock(&scp->send_lock);
+
 	 /* Wait until SCP receives the last command */
 	timeout = jiffies + msecs_to_jiffies(2000);
 	do {
 		if (time_after(jiffies, timeout)) {
 			dev_err(scp->dev, "%s: IPI timeout!\n", __func__);
 			ret = -ETIMEDOUT;
-			goto clock_disable;
+			goto unlock_mutex;
 		}
 	} while (readl(scp->reg_base + scp->data->host_to_scp_reg));
 
@@ -205,10 +205,9 @@
 			ret = 0;
 	}
 
-clock_disable:
-	clk_disable_unprepare(scp->clk);
 unlock_mutex:
 	mutex_unlock(&scp->send_lock);
+	clk_disable_unprepare(scp->clk);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_pil_info.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_pil_info.c
@@ -104,7 +104,7 @@
 	return -ENOMEM;
 
 found_unused:
-	memcpy_toio(entry, image, PIL_RELOC_NAME_LEN);
+	memcpy_toio(entry, image, strnlen(image, PIL_RELOC_NAME_LEN));
 found_existing:
 	/* Use two writel() as base is only aligned to 4 bytes on odd entries */
 	writel(base, entry + PIL_RELOC_NAME_LEN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_q6v5_adsp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_q6v5_adsp.c
@@ -406,6 +406,7 @@
 	}
 
 	ret = of_address_to_resource(node, 0, &r);
+	of_node_put(node);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_q6v5_mss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_q6v5_mss.c
@@ -17,6 +17,7 @@
 #include <linux/module.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
+#include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
 #include <linux/pm_runtime.h>
@@ -192,6 +193,9 @@
 	size_t mba_size;
 	size_t dp_size;
 
+	phys_addr_t mdata_phys;
+	size_t mdata_size;
+
 	phys_addr_t mpss_phys;
 	phys_addr_t mpss_reloc;
 	size_t mpss_size;
@@ -832,15 +836,35 @@
 	if (IS_ERR(metadata))
 		return PTR_ERR(metadata);
 
-	ptr = dma_alloc_attrs(qproc->dev, size, &phys, GFP_KERNEL, dma_attrs);
-	if (!ptr) {
-		kfree(metadata);
-		dev_err(qproc->dev, "failed to allocate mdt buffer\n");
-		return -ENOMEM;
+	if (qproc->mdata_phys) {
+		if (size > qproc->mdata_size) {
+			ret = -EINVAL;
+			dev_err(qproc->dev, "metadata size outside memory range\n");
+			goto free_metadata;
+		}
+
+		phys = qproc->mdata_phys;
+		ptr = memremap(qproc->mdata_phys, size, MEMREMAP_WC);
+		if (!ptr) {
+			ret = -EBUSY;
+			dev_err(qproc->dev, "unable to map memory region: %pa+%zx\n",
+				&qproc->mdata_phys, size);
+			goto free_metadata;
+		}
+	} else {
+		ptr = dma_alloc_attrs(qproc->dev, size, &phys, GFP_KERNEL, dma_attrs);
+		if (!ptr) {
+			ret = -ENOMEM;
+			dev_err(qproc->dev, "failed to allocate mdt buffer\n");
+			goto free_metadata;
+		}
 	}
 
 	memcpy(ptr, metadata, size);
 
+	if (qproc->mdata_phys)
+		memunmap(ptr);
+
 	/* Hypervisor mapping to access metadata by modem */
 	mdata_perm = BIT(QCOM_SCM_VMID_HLOS);
 	ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, false, true,
@@ -869,7 +893,9 @@
 			 "mdt buffer not reclaimed system may become unstable\n");
 
 free_dma_attrs:
-	dma_free_attrs(qproc->dev, size, ptr, phys, dma_attrs);
+	if (!qproc->mdata_phys)
+		dma_free_attrs(qproc->dev, size, ptr, phys, dma_attrs);
+free_metadata:
 	kfree(metadata);
 
 	return ret < 0 ? ret : 0;
@@ -977,6 +1003,9 @@
 		goto disable_active_clks;
 	}
 
+	if (qproc->has_mba_logs)
+		qcom_pil_info_store("mba", qproc->mba_phys, MBA_LOG_SIZE);
+
 	writel(qproc->mba_phys, qproc->rmb_base + RMB_MBA_IMAGE_REG);
 	if (qproc->dp_size) {
 		writel(qproc->mba_phys + SZ_1M, qproc->rmb_base + RMB_PMI_CODE_START_REG);
@@ -1565,6 +1594,13 @@
 	while (pd_names[num_pds])
 		num_pds++;
 
+	/* Handle single power domain */
+	if (num_pds == 1 && dev->pm_domain) {
+		devs[0] = dev;
+		pm_runtime_enable(dev);
+		return 1;
+	}
+
 	for (i = 0; i < num_pds; i++) {
 		devs[i] = dev_pm_domain_attach_by_name(dev, pd_names[i]);
 		if (IS_ERR_OR_NULL(devs[i])) {
@@ -1585,8 +1621,15 @@
 static void q6v5_pds_detach(struct q6v5 *qproc, struct device **pds,
 			    size_t pd_count)
 {
+	struct device *dev = qproc->dev;
 	int i;
 
+	/* Handle single power domain */
+	if (pd_count == 1 && dev->pm_domain) {
+		pm_runtime_disable(dev);
+		return;
+	}
+
 	for (i = 0; i < pd_count; i++)
 		dev_pm_domain_detach(pds[i], false);
 }
@@ -1615,6 +1658,7 @@
 static int q6v5_alloc_memory_region(struct q6v5 *qproc)
 {
 	struct device_node *child;
+	struct reserved_mem *rmem;
 	struct device_node *node;
 	struct resource r;
 	int ret;
@@ -1624,18 +1668,20 @@
 	 * reserved memory regions from device's memory-region property.
 	 */
 	child = of_get_child_by_name(qproc->dev->of_node, "mba");
-	if (!child)
+	if (!child) {
 		node = of_parse_phandle(qproc->dev->of_node,
 					"memory-region", 0);
-	else
+	} else {
 		node = of_parse_phandle(child, "memory-region", 0);
+		of_node_put(child);
+	}
 
 	ret = of_address_to_resource(node, 0, &r);
+	of_node_put(node);
 	if (ret) {
 		dev_err(qproc->dev, "unable to resolve mba region\n");
 		return ret;
 	}
-	of_node_put(node);
 
 	qproc->mba_phys = r.start;
 	qproc->mba_size = resource_size(&r);
@@ -1646,18 +1692,39 @@
 	} else {
 		child = of_get_child_by_name(qproc->dev->of_node, "mpss");
 		node = of_parse_phandle(child, "memory-region", 0);
+		of_node_put(child);
 	}
 
 	ret = of_address_to_resource(node, 0, &r);
+	of_node_put(node);
 	if (ret) {
 		dev_err(qproc->dev, "unable to resolve mpss region\n");
 		return ret;
 	}
-	of_node_put(node);
 
 	qproc->mpss_phys = qproc->mpss_reloc = r.start;
 	qproc->mpss_size = resource_size(&r);
 
+	if (!child) {
+		node = of_parse_phandle(qproc->dev->of_node, "memory-region", 2);
+	} else {
+		child = of_get_child_by_name(qproc->dev->of_node, "metadata");
+		node = of_parse_phandle(child, "memory-region", 0);
+		of_node_put(child);
+	}
+
+	if (!node)
+		return 0;
+
+	rmem = of_reserved_mem_lookup(node);
+	if (!rmem) {
+		dev_err(qproc->dev, "unable to resolve metadata region\n");
+		return -EINVAL;
+	}
+
+	qproc->mdata_phys = rmem->base;
+	qproc->mdata_size = rmem->size;
+
 	return 0;
 }
 
@@ -2028,13 +2095,13 @@
 			.supply = "pll",
 			.uA = 100000,
 		},
-		{}
-	},
-	.fallback_proxy_supply = (struct qcom_mss_reg_res[]) {
 		{
 			.supply = "mx",
 			.uV = 1050000,
 		},
+		{}
+	},
+	.fallback_proxy_supply = (struct qcom_mss_reg_res[]) {
 		{
 			.supply = "cx",
 			.uA = 100000,
@@ -2060,7 +2127,6 @@
 		NULL
 	},
 	.proxy_pd_names = (char*[]){
-		"mx",
 		"cx",
 		NULL
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_q6v5_pas.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_q6v5_pas.c
@@ -87,6 +87,9 @@
 {
 	struct qcom_adsp *adsp = rproc->priv;
 
+	if (rproc->dump_conf == RPROC_COREDUMP_DISABLED)
+		return;
+
 	qcom_minidump(rproc, adsp->minidump_id);
 }
 
@@ -327,16 +330,16 @@
 	if (!pd_names)
 		return 0;
 
+	while (pd_names[num_pds])
+		num_pds++;
+
 	/* Handle single power domain */
-	if (dev->pm_domain) {
+	if (num_pds == 1 && dev->pm_domain) {
 		devs[0] = dev;
 		pm_runtime_enable(dev);
 		return 1;
 	}
 
-	while (pd_names[num_pds])
-		num_pds++;
-
 	for (i = 0; i < num_pds; i++) {
 		devs[i] = dev_pm_domain_attach_by_name(dev, pd_names[i]);
 		if (IS_ERR_OR_NULL(devs[i])) {
@@ -361,7 +364,7 @@
 	int i;
 
 	/* Handle single power domain */
-	if (dev->pm_domain && pd_count) {
+	if (pd_count == 1 && dev->pm_domain) {
 		pm_runtime_disable(dev);
 		return;
 	}
@@ -383,6 +386,7 @@
 	}
 
 	ret = of_address_to_resource(node, 0, &r);
+	of_node_put(node);
 	if (ret)
 		return ret;
 
@@ -495,6 +499,7 @@
 detach_active_pds:
 	adsp_pds_detach(adsp, adsp->active_pds, adsp->active_pd_count);
 free_rproc:
+	device_init_wakeup(adsp->dev, false);
 	rproc_free(rproc);
 
 	return ret;
@@ -510,6 +515,8 @@
 	qcom_remove_sysmon_subdev(adsp->sysmon);
 	qcom_remove_smd_subdev(adsp->rproc, &adsp->smd_subdev);
 	qcom_remove_ssr_subdev(adsp->rproc, &adsp->ssr_subdev);
+	adsp_pds_detach(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
+	device_init_wakeup(adsp->dev, false);
 	rproc_free(adsp->rproc);
 
 	return 0;
@@ -661,6 +668,7 @@
 	},
 	.proxy_pd_names = (char*[]){
 		"cx",
+		"mxc",
 		NULL
 	},
 	.ssr_name = "cdsp",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_q6v5_wcss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_q6v5_wcss.c
@@ -351,7 +351,7 @@
 	if (ret) {
 		dev_err(wcss->dev,
 			"xo cbcr enabling timed out (rc:%d)\n", ret);
-		return ret;
+		goto disable_xo_cbcr_clk;
 	}
 
 	writel(0, wcss->reg_base + Q6SS_CGC_OVERRIDE);
@@ -417,6 +417,7 @@
 	val = readl(wcss->reg_base + Q6SS_SLEEP_CBCR);
 	val &= ~Q6SS_CLK_ENABLE;
 	writel(val, wcss->reg_base + Q6SS_SLEEP_CBCR);
+disable_xo_cbcr_clk:
 	val = readl(wcss->reg_base + Q6SS_XO_CBCR);
 	val &= ~Q6SS_CLK_ENABLE;
 	writel(val, wcss->reg_base + Q6SS_XO_CBCR);
@@ -827,6 +828,9 @@
 	int ret;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qdsp6");
+	if (!res)
+		return -EINVAL;
+
 	wcss->reg_base = devm_ioremap(&pdev->dev, res->start,
 				      resource_size(res));
 	if (!wcss->reg_base)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_sysmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_sysmon.c
@@ -41,6 +41,7 @@
 	struct completion comp;
 	struct completion ind_comp;
 	struct completion shutdown_comp;
+	struct completion ssctl_comp;
 	struct mutex lock;
 
 	bool ssr_ack;
@@ -445,6 +446,8 @@
 
 	svc->priv = sysmon;
 
+	complete(&sysmon->ssctl_comp);
+
 	return 0;
 }
 
@@ -501,6 +504,7 @@
 		.ssr_event = SSCTL_SSR_EVENT_AFTER_POWERUP
 	};
 
+	reinit_completion(&sysmon->ssctl_comp);
 	mutex_lock(&sysmon->state_lock);
 	sysmon->state = SSCTL_SSR_EVENT_AFTER_POWERUP;
 	blocking_notifier_call_chain(&sysmon_notifiers, 0, (void *)&event);
@@ -545,6 +549,11 @@
 	if (crashed)
 		return;
 
+	if (sysmon->ssctl_instance) {
+		if (!wait_for_completion_timeout(&sysmon->ssctl_comp, HZ / 2))
+			dev_err(sysmon->dev, "timeout waiting for ssctl service\n");
+	}
+
 	if (sysmon->ssctl_version)
 		sysmon->shutdown_acked = ssctl_request_shutdown(sysmon);
 	else if (sysmon->ept)
@@ -631,6 +640,7 @@
 	init_completion(&sysmon->comp);
 	init_completion(&sysmon->ind_comp);
 	init_completion(&sysmon->shutdown_comp);
+	init_completion(&sysmon->ssctl_comp);
 	mutex_init(&sysmon->lock);
 	mutex_init(&sysmon->state_lock);
 
@@ -640,7 +650,9 @@
 		if (sysmon->shutdown_irq != -ENODATA) {
 			dev_err(sysmon->dev,
 				"failed to retrieve shutdown-ack IRQ\n");
-			return ERR_PTR(sysmon->shutdown_irq);
+			ret = sysmon->shutdown_irq;
+			kfree(sysmon);
+			return ERR_PTR(ret);
 		}
 	} else {
 		ret = devm_request_threaded_irq(sysmon->dev,
@@ -651,6 +663,7 @@
 		if (ret) {
 			dev_err(sysmon->dev,
 				"failed to acquire shutdown-ack IRQ\n");
+			kfree(sysmon);
 			return ERR_PTR(ret);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/qcom_wcnss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/qcom_wcnss.c
@@ -468,6 +468,7 @@
 			     irq_handler_t thread_fn)
 {
 	int ret;
+	int irq_number;
 
 	ret = platform_get_irq_byname(pdev, name);
 	if (ret < 0 && optional) {
@@ -478,14 +479,19 @@
 		return ret;
 	}
 
+	irq_number = ret;
+
 	ret = devm_request_threaded_irq(&pdev->dev, ret,
 					NULL, thread_fn,
 					IRQF_TRIGGER_RISING | IRQF_ONESHOT,
 					"wcnss", wcnss);
-	if (ret)
+	if (ret) {
 		dev_err(&pdev->dev, "request %s IRQ failed\n", name);
+		return ret;
+	}
 
-	return ret;
+	/* Return the IRQ number if the IRQ was successfully acquired */
+	return irq_number;
 }
 
 static int wcnss_alloc_memory_region(struct qcom_wcnss *wcnss)
@@ -501,6 +507,7 @@
 	}
 
 	ret = of_address_to_resource(node, 0, &r);
+	of_node_put(node);
 	if (ret)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/remoteproc_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/remoteproc_core.c
@@ -556,9 +556,6 @@
 	/* Initialise vdev subdevice */
 	snprintf(name, sizeof(name), "vdev%dbuffer", rvdev->index);
 	rvdev->dev.parent = &rproc->dev;
-	ret = copy_dma_range_map(&rvdev->dev, rproc->dev.parent);
-	if (ret)
-		return ret;
 	rvdev->dev.release = rproc_rvdev_release;
 	dev_set_name(&rvdev->dev, "%s#%s", dev_name(rvdev->dev.parent), name);
 	dev_set_drvdata(&rvdev->dev, rvdev);
@@ -568,6 +565,11 @@
 		put_device(&rvdev->dev);
 		return ret;
 	}
+
+	ret = copy_dma_range_map(&rvdev->dev, rproc->dev.parent);
+	if (ret)
+		goto free_rvdev;
+
 	/* Make device dma capable by inheriting from parent's capabilities */
 	set_dma_ops(&rvdev->dev, get_dma_ops(rproc->dev.parent));
 
@@ -1953,12 +1955,18 @@
 
 	mutex_lock(&rproc->lock);
 
-	if (rproc->state == RPROC_CRASHED || rproc->state == RPROC_OFFLINE) {
+	if (rproc->state == RPROC_CRASHED) {
 		/* handle only the first crash detected */
 		mutex_unlock(&rproc->lock);
 		return;
 	}
 
+	if (rproc->state == RPROC_OFFLINE) {
+		/* Don't recover if the remote processor was stopped */
+		mutex_unlock(&rproc->lock);
+		goto out;
+	}
+
 	rproc->state = RPROC_CRASHED;
 	dev_err(dev, "handling crash #%u in %s\n", ++rproc->crash_cnt,
 		rproc->name);
@@ -1968,6 +1976,7 @@
 	if (!rproc->recovery_disabled)
 		rproc_trigger_recovery(rproc);
 
+out:
 	pm_relax(rproc->dev.parent);
 }
 
@@ -2093,6 +2102,7 @@
 	kfree(rproc->cached_table);
 	rproc->cached_table = NULL;
 	rproc->table_ptr = NULL;
+	rproc->table_sz = 0;
 out:
 	mutex_unlock(&rproc->lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/remoteproc_coredump.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/remoteproc_coredump.c
@@ -152,8 +152,8 @@
 			       struct rproc_dump_segment *segment,
 			       size_t offset, size_t size)
 {
+	bool is_iomem = false;
 	void *ptr;
-	bool is_iomem;
 
 	if (segment->dump) {
 		segment->dump(rproc, segment, dest, offset, size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/remoteproc_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/remoteproc_debugfs.c
@@ -76,7 +76,7 @@
 	int ret, err = 0;
 	char buf[20];
 
-	if (count > sizeof(buf))
+	if (count < 1 || count > sizeof(buf))
 		return -EINVAL;
 
 	ret = copy_from_user(buf, user_buf, count);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/remoteproc_elf_loader.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/remoteproc_elf_loader.c
@@ -178,8 +178,8 @@
 		u64 filesz = elf_phdr_get_p_filesz(class, phdr);
 		u64 offset = elf_phdr_get_p_offset(class, phdr);
 		u32 type = elf_phdr_get_p_type(class, phdr);
+		bool is_iomem = false;
 		void *ptr;
-		bool is_iomem;
 
 		if (type != PT_LOAD)
 			continue;
@@ -220,7 +220,7 @@
 		/* put the segment where the remote processor expects it */
 		if (filesz) {
 			if (is_iomem)
-				memcpy_fromio(ptr, (void __iomem *)(elf_data + offset), filesz);
+				memcpy_toio((void __iomem *)ptr, elf_data + offset, filesz);
 			else
 				memcpy(ptr, elf_data + offset, filesz);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/remoteproc_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/remoteproc_internal.h
@@ -196,4 +196,27 @@
 	return (val <= (size_t) -1);
 }
 
+static inline
+bool rproc_allow_sysfs_kick(struct rproc *rproc)
+{
+	return (rproc->sysfs_kick) ? true : false;
+}
+
+static inline
+bool rproc_peek_remote_kick(struct rproc *rproc, char *buf, size_t *len)
+{
+	if (rproc->ops->peek_remote_kick)
+		return rproc->ops->peek_remote_kick(rproc, buf, len);
+	else
+		return false;
+}
+
+static inline
+void rproc_ack_remote_kick(struct rproc *rproc)
+{
+	if (rproc->ops->ack_remote_kick)
+		rproc->ops->ack_remote_kick(rproc);
+}
+
+int rproc_create_kick_sysfs(struct rproc *rproc);
 #endif /* REMOTEPROC_INTERNAL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/remoteproc_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/remoteproc_sysfs.c
@@ -220,6 +220,85 @@
 }
 static DEVICE_ATTR_RW(state);
 
+/**
+ * kick_store() - Kick remote from sysfs.
+ * @dev: remoteproc device
+ * @attr: sysfs device attribute
+ * @buf: sysfs buffer
+ * @count: size of the contents in buf
+ *
+ * It will just raise a signal, no content is expected for now.
+ *
+ * Return: the input count if it allows kick from sysfs,
+ * as it is always expected to succeed.
+ */
+static ssize_t kick_store(struct device *dev,
+			  struct device_attribute *attr,
+			  const char *buf, size_t count)
+{
+	struct rproc *rproc = to_rproc(dev);
+	int id;
+	size_t cpy_len;
+
+	(void)attr;
+	cpy_len = count <= sizeof(id) ? count : sizeof(id);
+	memcpy((char *)(&id), buf, cpy_len);
+
+	if (rproc->ops->kick)
+		rproc->ops->kick(rproc, id);
+	else
+		count = -EINVAL;
+	return count;
+}
+static DEVICE_ATTR_WO(kick);
+
+/**
+ * remote_kick_show() - Check if remote has kicked
+ * @dev: remoteproc device
+ * @attr: sysfs device attribute
+ * @buf: sysfs buffer
+ *
+ * It will check if the remote has kicked.
+ *
+ * Return: always 2, and the value in the sysfs buffer
+ * shows if the remote has kicked. '0' - not kicked, '1' - kicked.
+ */
+static ssize_t remote_kick_show(struct device *dev,
+				struct device_attribute *attr,
+				char *buf)
+{
+	struct rproc *rproc = to_rproc(dev);
+
+	buf[0] = '0';
+	buf[1] = '\n';
+	if (rproc_peek_remote_kick(rproc, NULL, NULL))
+		buf[0] = '1';
+	return 2;
+}
+
+/**
+ * remote_kick_store() - Ack the kick from remote
+ * @dev: remoteproc device
+ * @attr: sysfs device attribute
+ * @buf: sysfs buffer
+ * @count: size of the contents in buf
+ *
+ * It will ack the remote, no response contents is expected.
+ *
+ * Return: the input count if it allows kick from sysfs,
+ * as it is always expected to succeed.
+ */
+static ssize_t remote_kick_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	struct rproc *rproc = to_rproc(dev);
+
+	rproc_ack_remote_kick(rproc);
+	return count;
+}
+static DEVICE_ATTR_RW(remote_kick);
+
 /* Expose the name of the remote processor via sysfs */
 static ssize_t name_show(struct device *dev, struct device_attribute *attr,
 			 char *buf)
@@ -253,6 +332,34 @@
 	.dev_groups	= rproc_devgroups,
 };
 
+/**
+ * rproc_create_kick_sysfs() - create kick remote sysfs entry
+ * @rproc: remoteproc
+ *
+ * It will create kick remote sysfs entry if kick remote
+ * from sysfs is allowed.
+ *
+ * Return: 0 for success, and negative value for failure.
+ */
+int rproc_create_kick_sysfs(struct rproc *rproc)
+{
+	struct device *dev = &rproc->dev;
+	int ret;
+
+	if (!rproc_allow_sysfs_kick(rproc))
+		return -EINVAL;
+	ret = sysfs_create_file(&dev->kobj, &dev_attr_kick.attr);
+	if (ret) {
+		dev_err(dev, "failed to create sysfs for kick.\n");
+		return ret;
+	}
+	ret = sysfs_create_file(&dev->kobj, &dev_attr_remote_kick.attr);
+	if (ret)
+		dev_err(dev, "failed to create sysfs for remote kick.\n");
+	return ret;
+}
+EXPORT_SYMBOL(rproc_create_kick_sysfs);
+
 int __init rproc_init_sysfs(void)
 {
 	/* create remoteproc device class for sysfs */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/st_remoteproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/st_remoteproc.c
@@ -129,6 +129,7 @@
 	while (of_phandle_iterator_next(&it) == 0) {
 		rmem = of_reserved_mem_lookup(it.node);
 		if (!rmem) {
+			of_node_put(it.node);
 			dev_err(dev, "unable to acquire memory-region\n");
 			return -EINVAL;
 		}
@@ -150,8 +151,10 @@
 							   it.node->name);
 		}
 
-		if (!mem)
+		if (!mem) {
+			of_node_put(it.node);
 			return -ENOMEM;
+		}
 
 		rproc_add_carveout(rproc, mem);
 		index++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/stm32_rproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/stm32_rproc.c
@@ -118,10 +118,10 @@
 	struct device *dev = rproc->dev.parent;
 	void *va;
 
-	dev_dbg(dev, "map memory: %pa+%x\n", &mem->dma, mem->len);
-	va = ioremap_wc(mem->dma, mem->len);
+	dev_dbg(dev, "map memory: %pad+%zx\n", &mem->dma, mem->len);
+	va = (__force void *)ioremap_wc(mem->dma, mem->len);
 	if (IS_ERR_OR_NULL(va)) {
-		dev_err(dev, "Unable to map memory region: %pa+%x\n",
+		dev_err(dev, "Unable to map memory region: %pad+0x%zx\n",
 			&mem->dma, mem->len);
 		return -ENOMEM;
 	}
@@ -136,7 +136,7 @@
 				   struct rproc_mem_entry *mem)
 {
 	dev_dbg(rproc->dev.parent, "unmap memory: %pa\n", &mem->dma);
-	iounmap(mem->va);
+	iounmap((__force __iomem void *)mem->va);
 
 	return 0;
 }
@@ -223,11 +223,13 @@
 	while (of_phandle_iterator_next(&it) == 0) {
 		rmem = of_reserved_mem_lookup(it.node);
 		if (!rmem) {
+			of_node_put(it.node);
 			dev_err(dev, "unable to acquire memory-region\n");
 			return -EINVAL;
 		}
 
 		if (stm32_rproc_pa_to_da(rproc, rmem->base, &da) < 0) {
+			of_node_put(it.node);
 			dev_err(dev, "memory region not valid %pa\n",
 				&rmem->base);
 			return -EINVAL;
@@ -254,8 +256,10 @@
 							   it.node->name);
 		}
 
-		if (!mem)
+		if (!mem) {
+			of_node_put(it.node);
 			return -ENOMEM;
+		}
 
 		rproc_add_carveout(rproc, mem);
 		index++;
@@ -287,8 +291,16 @@
 	struct stm32_mbox *mb = container_of(work, struct stm32_mbox, vq_work);
 	struct rproc *rproc = dev_get_drvdata(mb->client.dev);
 
+	mutex_lock(&rproc->lock);
+
+	if (rproc->state != RPROC_RUNNING && rproc->state != RPROC_ATTACHED)
+		goto unlock_mutex;
+
 	if (rproc_vq_interrupt(rproc, mb->vq_id) == IRQ_NONE)
 		dev_dbg(&rproc->dev, "no message found in vq%d\n", mb->vq_id);
+
+unlock_mutex:
+	mutex_unlock(&rproc->lock);
 }
 
 static void stm32_rproc_mb_callback(struct mbox_client *cl, void *data)
@@ -615,7 +627,7 @@
 
 	ddata->rsc_va = devm_ioremap_wc(dev, rsc_pa, RSC_TBL_SIZE);
 	if (IS_ERR_OR_NULL(ddata->rsc_va)) {
-		dev_err(dev, "Unable to map memory region: %pa+%zx\n",
+		dev_err(dev, "Unable to map memory region: %pa+%x\n",
 			&rsc_pa, RSC_TBL_SIZE);
 		ddata->rsc_va = NULL;
 		return ERR_PTR(-ENOMEM);
@@ -629,7 +641,7 @@
 	 * entire area by overwriting it with the initial values stored in rproc->clean_table.
 	 */
 	*table_sz = RSC_TBL_SIZE;
-	return (struct resource_table *)ddata->rsc_va;
+	return (__force struct resource_table *)ddata->rsc_va;
 }
 
 static const struct rproc_ops st_rproc_ops = {
@@ -877,7 +889,7 @@
 	return 0;
 }
 
-static int __maybe_unused stm32_rproc_suspend(struct device *dev)
+static int stm32_rproc_suspend(struct device *dev)
 {
 	struct rproc *rproc = dev_get_drvdata(dev);
 	struct stm32_rproc *ddata = rproc->priv;
@@ -888,7 +900,7 @@
 	return 0;
 }
 
-static int __maybe_unused stm32_rproc_resume(struct device *dev)
+static int stm32_rproc_resume(struct device *dev)
 {
 	struct rproc *rproc = dev_get_drvdata(dev);
 	struct stm32_rproc *ddata = rproc->priv;
@@ -899,16 +911,16 @@
 	return 0;
 }
 
-static SIMPLE_DEV_PM_OPS(stm32_rproc_pm_ops,
-			 stm32_rproc_suspend, stm32_rproc_resume);
+static DEFINE_SIMPLE_DEV_PM_OPS(stm32_rproc_pm_ops,
+				stm32_rproc_suspend, stm32_rproc_resume);
 
 static struct platform_driver stm32_rproc_driver = {
 	.probe = stm32_rproc_probe,
 	.remove = stm32_rproc_remove,
 	.driver = {
 		.name = "stm32-rproc",
-		.pm = &stm32_rproc_pm_ops,
-		.of_match_table = of_match_ptr(stm32_rproc_match),
+		.pm = pm_ptr(&stm32_rproc_pm_ops),
+		.of_match_table = stm32_rproc_match,
 	},
 };
 module_platform_driver(stm32_rproc_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/ti_k3_r5_remoteproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/ti_k3_r5_remoteproc.c
@@ -1430,6 +1430,7 @@
 		if (!cpdev) {
 			ret = -ENODEV;
 			dev_err(dev, "could not get R5 core platform device\n");
+			of_node_put(child);
 			goto fail;
 		}
 
@@ -1438,6 +1439,7 @@
 			dev_err(dev, "k3_r5_core_of_init failed, ret = %d\n",
 				ret);
 			put_device(&cpdev->dev);
+			of_node_put(child);
 			goto fail;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/zynq_remoteproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/zynq_remoteproc.c
@@ -0,0 +1,430 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Zynq Remote Processor driver
+ *
+ * Copyright (C) 2012 Michal Simek <monstr@monstr.eu>
+ * Copyright (C) 2012 PetaLogix
+ *
+ * Based on origin OMAP Remote Processor driver
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Copyright (C) 2011 Google, Inc.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/remoteproc.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/smp.h>
+#include <linux/irqchip/arm-gic.h>
+#include <asm/outercache.h>
+#include <linux/slab.h>
+#include <linux/cpu.h>
+#include <linux/genalloc.h>
+#include <../../arch/arm/mach-zynq/common.h>
+
+#include "remoteproc_internal.h"
+
+#define MAX_NUM_VRINGS 2
+#define NOTIFYID_ANY (-1)
+/* Maximum on chip memories used by the driver*/
+#define MAX_ON_CHIP_MEMS	32
+#define REMOTE_SGI		0
+#define HOST_SGI		1
+
+static int vring_sgis[MAX_NUM_VRINGS] = { 14, 15 };
+/* count number of SGIs passed via command line if applicable. */
+static int n_vring_sgis = MAX_NUM_VRINGS;
+
+/* Structure for storing IRQs */
+struct irq_list {
+	int irq;
+	struct list_head list;
+};
+
+/* Structure for IPIs */
+struct ipi_info {
+	u32 irq;
+	u32 notifyid;
+	bool pending;
+};
+
+/**
+ * struct zynq_mem_res - zynq memory resource for firmware memory
+ * @res: memory resource
+ * @node: list node
+ */
+struct zynq_mem_res {
+	struct resource res;
+	struct list_head node;
+};
+
+/**
+ * struct zynq_rproc_data - zynq rproc private data
+ * @irqs: inter processor soft IRQs
+ * @ipi_desc: list of IRQ descriptors for each vring's IRQ.
+ * @rproc: pointer to remoteproc instance
+ * @ipis: interrupt processor interrupts statistics
+ * @fw_mems: list of firmware memories
+ */
+struct zynq_rproc_pdata {
+	int irqs[MAX_NUM_VRINGS];
+	struct irq_desc *ipi_desc[MAX_NUM_VRINGS];
+	struct rproc *rproc;
+	struct ipi_info ipis[MAX_NUM_VRINGS];
+	struct list_head fw_mems;
+};
+
+static bool autoboot __read_mostly;
+
+/* Store rproc for IPI handler */
+static struct rproc *rproc;
+static struct work_struct workqueue;
+
+static irqreturn_t zynq_remoteproc_interrupt(int irq, void *dev_id)
+{
+	struct zynq_rproc_pdata *local = dev_id;
+
+	dev_dbg(local->rproc->dev.parent, "KICK Linux because of pending message\n");
+	schedule_work(&workqueue);
+
+	return IRQ_HANDLED;
+}
+
+struct irqaction action = {
+	.handler = zynq_remoteproc_interrupt,
+};
+
+static void handle_event(struct work_struct *work)
+{
+	struct zynq_rproc_pdata *local = rproc->priv;
+
+	rproc_vq_interrupt(local->rproc, local->ipis[0].notifyid);
+}
+
+static void kick_pending_ipi(struct rproc *rproc)
+{
+	struct zynq_rproc_pdata *local = rproc->priv;
+	int i;
+
+	for (i = 0; i < MAX_NUM_VRINGS; i++) {
+		/* Send swirq to firmware */
+		if (local->ipis[i].pending) {
+			gic_send_sgi(1, local->irqs[HOST_SGI]);
+			local->ipis[i].pending = false;
+		}
+	}
+}
+
+static int zynq_rproc_start(struct rproc *rproc)
+{
+	struct device *dev = rproc->dev.parent;
+	int ret;
+
+	dev_dbg(dev, "%s\n", __func__);
+	INIT_WORK(&workqueue, handle_event);
+
+	ret = remove_cpu(1);
+	/* EBUSY means CPU is already released */
+	if (ret && (ret != -EBUSY)) {
+		dev_err(dev, "Can't release cpu1\n");
+		return ret;
+	}
+
+	ret = zynq_cpun_start(rproc->bootaddr, 1);
+	/* Trigger pending kicks */
+	kick_pending_ipi(rproc);
+
+	return ret;
+}
+
+/* kick a firmware */
+static void zynq_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynq_rproc_pdata *local = rproc->priv;
+	struct rproc_vdev *rvdev, *rvtmp;
+	int i;
+
+	dev_dbg(dev, "KICK Firmware to start send messages vqid %d\n", vqid);
+
+	list_for_each_entry_safe(rvdev, rvtmp, &rproc->rvdevs, node) {
+		for (i = 0; i < MAX_NUM_VRINGS; i++) {
+			struct rproc_vring *rvring = &rvdev->vring[i];
+
+			/* Send swirq to firmware */
+			if (rvring->notifyid == vqid) {
+				local->ipis[i].notifyid = vqid;
+				/* As we do not turn off CPU1 until start,
+				 * we delay firmware kick
+				 */
+				if (rproc->state == RPROC_RUNNING)
+					gic_send_sgi(1,
+						     local->irqs[REMOTE_SGI]);
+				else
+					local->ipis[i].pending = true;
+			}
+		}
+	}
+}
+
+/* power off the remote processor */
+static int zynq_rproc_stop(struct rproc *rproc)
+{
+	int ret;
+	struct device *dev = rproc->dev.parent;
+
+	dev_dbg(rproc->dev.parent, "%s\n", __func__);
+
+	/* Cpu can't be power on - for example in nosmp mode */
+	ret = add_cpu(1);
+	if (ret)
+		dev_err(dev, "Can't power on cpu1 %d\n", ret);
+
+	return 0;
+}
+
+static int zynq_parse_fw(struct rproc *rproc, const struct firmware *fw)
+{
+	int num_mems, i, ret;
+	struct device *dev = rproc->dev.parent;
+	struct device_node *np = dev->of_node;
+	struct rproc_mem_entry *mem;
+
+	num_mems = of_count_phandle_with_args(np, "memory-region", NULL);
+	if (num_mems <= 0)
+		return 0;
+	for (i = 0; i < num_mems; i++) {
+		struct device_node *node;
+		struct reserved_mem *rmem;
+
+		node = of_parse_phandle(np, "memory-region", i);
+		rmem = of_reserved_mem_lookup(node);
+		if (!rmem) {
+			dev_err(dev, "unable to acquire memory-region\n");
+			return -EINVAL;
+		}
+		if (strstr(node->name, "vdev") &&
+			strstr(node->name, "buffer")) {
+			/* Register DMA region */
+			mem = rproc_mem_entry_init(dev, NULL,
+						   (dma_addr_t)rmem->base,
+						   rmem->size, rmem->base,
+						   NULL, NULL,
+						   node->name);
+			if (!mem) {
+				dev_err(dev,
+					"unable to initialize memory-region %s \n",
+					node->name);
+				return -ENOMEM;
+			}
+			rproc_add_carveout(rproc, mem);
+		} else if (strstr(node->name, "vdev") &&
+			   strstr(node->name, "vring")) {
+			/* Register vring */
+			mem = rproc_mem_entry_init(dev, NULL,
+						   (dma_addr_t)rmem->base,
+						   rmem->size, rmem->base,
+						   NULL, NULL,
+						   node->name);
+			mem->va = devm_ioremap_wc(dev, rmem->base, rmem->size);
+			if (!mem->va)
+				return -ENOMEM;
+			if (!mem) {
+				dev_err(dev,
+					"unable to initialize memory-region %s\n",
+					node->name);
+				return -ENOMEM;
+			}
+			rproc_add_carveout(rproc, mem);
+		} else {
+			mem = rproc_of_resm_mem_entry_init(dev, i,
+							rmem->size,
+							rmem->base,
+							node->name);
+			if (!mem) {
+				dev_err(dev,
+					"unable to initialize memory-region %s \n",
+					node->name);
+				return -ENOMEM;
+			}
+			mem->va = devm_ioremap_wc(dev, rmem->base, rmem->size);
+			if (!mem->va)
+				return -ENOMEM;
+
+			rproc_add_carveout(rproc, mem);
+		}
+	}
+
+	ret = rproc_elf_load_rsc_table(rproc, fw);
+	if (ret == -EINVAL)
+		ret = 0;
+	return ret;
+}
+
+static struct rproc_ops zynq_rproc_ops = {
+	.start		= zynq_rproc_start,
+	.stop		= zynq_rproc_stop,
+	.load		= rproc_elf_load_segments,
+	.parse_fw	= zynq_parse_fw,
+	.find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
+	.get_boot_addr	= rproc_elf_get_boot_addr,
+	.kick		= zynq_rproc_kick,
+};
+
+static int zynq_remoteproc_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	int i, virq;
+	struct zynq_rproc_pdata *local;
+	/*
+	 * IRQ related structures are used for the following:
+	 * for each SGI interrupt ensure its mapped by GIC IRQ domain
+	 * and that each corresponding linux IRQ for the HW IRQ has
+	 * a handler for when receiving an interrupt from the remote
+	 * processor.
+	 */
+	struct irq_domain *domain;
+	struct irq_desc *ipi_desc;
+	struct irq_fwspec sgi_fwspec;
+	struct device_node *interrupt_parent, *node = (&pdev->dev)->of_node;
+
+	rproc = rproc_alloc(&pdev->dev, dev_name(&pdev->dev),
+			    &zynq_rproc_ops, NULL,
+		sizeof(struct zynq_rproc_pdata));
+	if (!rproc) {
+		dev_err(&pdev->dev, "rproc allocation failed\n");
+		ret = -ENOMEM;
+		return ret;
+	}
+	local = rproc->priv;
+	local->rproc = rproc;
+
+	platform_set_drvdata(pdev, rproc);
+
+	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(&pdev->dev, "dma_set_coherent_mask: %d\n", ret);
+		goto dma_mask_fault;
+	}
+
+	/* validate SGIs */
+	if (n_vring_sgis != MAX_NUM_VRINGS) {
+		dev_err(&pdev->dev, "invalid number of SGIs provided.\n");
+		return -EINVAL;
+	}
+
+	/* Find GIC controller to map SGIs. */
+	interrupt_parent = of_irq_find_parent(node);
+	if (!interrupt_parent) {
+		dev_err(&pdev->dev, "invalid phandle for interrupt parent.\n");
+		return -EINVAL;
+	}
+
+	/* Each SGI needs to be associated with GIC's IRQ domain. */
+	domain = irq_find_host(interrupt_parent);
+
+	/* Each mapping needs GIC domain when finding IRQ mapping. */
+	sgi_fwspec.fwnode = domain->fwnode;
+
+	/*
+	 * When irq domain looks at mapping each arg is as follows:
+	 * 1 args for: interrupt # (set later)
+	 */
+	sgi_fwspec.param_count = 1;
+
+	/*
+	 * For each SGI:
+	 * Set HW IRQ.
+	 * Get corresponding Linux IRQ.
+	 * Associate a handler for remotproc driver.
+	 * For the IRQ descriptor for each wire in handler for IRQ action.
+	 *   (this comes into play when receiving HW IRQ)
+	 * Save HW IRQ for later remoteproc handling.
+	 */
+	for (i = 0; i < MAX_NUM_VRINGS; i++) {
+		/* Set SGI's hwirq */
+		sgi_fwspec.param[0] = vring_sgis[i];
+		virq = irq_create_fwspec_mapping(&sgi_fwspec);
+		/*
+		 * Request_percpu_irq is not used because Linux only runs on
+		 * one CPU.
+		 */
+		ret = devm_request_irq(&pdev->dev, virq,
+				       zynq_remoteproc_interrupt,
+				       0, "vring0", local);
+		/*
+		 * The IPI descriptor relates Linux IRQ to HW IRQ and
+		 * irqaction. The irqaction will point to the zynq_remoteproc_interrupt.
+		 */
+		ipi_desc = irq_to_desc(virq);
+		ipi_desc->action = &action;
+		irq_set_status_flags(virq, IRQ_HIDDEN);
+		enable_percpu_irq(virq, 0);
+		local->irqs[i] = vring_sgis[i];
+	}
+
+	rproc->auto_boot = autoboot;
+
+	ret = rproc_add(local->rproc);
+	if (ret) {
+		dev_err(&pdev->dev, "rproc registration failed\n");
+		goto dma_mask_fault;
+	}
+
+	return 0;
+
+dma_mask_fault:
+	rproc_free(rproc);
+
+	return ret;
+}
+
+static int zynq_remoteproc_remove(struct platform_device *pdev)
+{
+	struct rproc *rproc = platform_get_drvdata(pdev);
+
+	dev_info(&pdev->dev, "%s\n", __func__);
+
+	rproc_del(rproc);
+
+	of_reserved_mem_device_release(&pdev->dev);
+	rproc_free(rproc);
+
+	return 0;
+}
+
+/* Match table for OF platform binding */
+static const struct of_device_id zynq_remoteproc_match[] = {
+	{ .compatible = "xlnx,zynq_remoteproc", },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, zynq_remoteproc_match);
+
+static struct platform_driver zynq_remoteproc_driver = {
+	.probe = zynq_remoteproc_probe,
+	.remove = zynq_remoteproc_remove,
+	.driver = {
+		.name = "zynq_remoteproc",
+		.of_match_table = zynq_remoteproc_match,
+	},
+};
+module_platform_driver(zynq_remoteproc_driver);
+
+module_param_named(autoboot,  autoboot, bool, 0444);
+MODULE_PARM_DESC(autoboot,
+		 "enable | disable autoboot. (default: false)");
+module_param_array(vring_sgis, int, &n_vring_sgis, 0);
+
+MODULE_AUTHOR("Michal Simek <monstr@monstr.eu");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Zynq remote processor control driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/remoteproc/zynqmp_r5_remoteproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/remoteproc/zynqmp_r5_remoteproc.c
@@ -0,0 +1,1076 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Zynq R5 Remote Processor driver
+ *
+ * Based on origin OMAP and Zynq Remote Processor driver
+ *
+ */
+
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/mailbox_client.h>
+#include <linux/mailbox/zynqmp-ipi-message.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/skbuff.h>
+#include <linux/sysfs.h>
+
+#include "remoteproc_internal.h"
+
+#define MAX_RPROCS	2 /* Support up to 2 RPU */
+#define BANK_LIST_PROP	"sram"
+#define DDR_LIST_PROP	"memory-region"
+#define PD_PROP		"power-domain"
+
+/* IPI buffer MAX length */
+#define IPI_BUF_LEN_MAX	32U
+/* RX mailbox client buffer max length */
+#define RX_MBOX_CLIENT_BUF_MAX	(IPI_BUF_LEN_MAX + \
+				 sizeof(struct zynqmp_ipi_message))
+#define MAX_BANKS 4U
+
+/**
+ * struct xlnx_r5_data - match data to handle SoC variations
+ * @versal_soc: flag to denote if running on Versal SoC.
+ */
+struct xlnx_r5_data {
+	bool versal_soc;
+};
+
+/*
+ * Map each Xilinx on-chip SRAM  Bank address to their own respective
+ * pm_node_id.
+ */
+struct sram_addr_data {
+	enum pm_node_id ids[MAX_BANKS];
+};
+
+/**
+ * struct zynqmp_r5_rproc - ZynqMP R5 core structure
+ *
+ * @rx_mc_buf: rx mailbox client buffer to save the rx message
+ * @tx_mc: tx mailbox client
+ * @rx_mc: rx mailbox client
+ * @mbox_work: mbox_work for the RPU remoteproc
+ * @tx_mc_skbs: socket buffers for tx mailbox client
+ * @dev: device of RPU instance
+ * @rproc: rproc handle
+ * @tx_chan: tx mailbox channel
+ * @rx_chan: rx mailbox channel
+ * @pnode_id: RPU CPU power domain id
+ * @elem: linked list item
+ * @versal: flag that if on, denotes this driver is for Versal SoC.
+ */
+struct zynqmp_r5_rproc {
+	unsigned char rx_mc_buf[RX_MBOX_CLIENT_BUF_MAX];
+	struct mbox_client tx_mc;
+	struct mbox_client rx_mc;
+	struct work_struct mbox_work;
+	struct sk_buff_head tx_mc_skbs;
+	struct device *dev;
+	struct rproc *rproc;
+	struct mbox_chan *tx_chan;
+	struct mbox_chan *rx_chan;
+	u32 pnode_id;
+	struct list_head elem;
+	bool versal;
+};
+
+/*
+ * r5_set_mode - set RPU operation mode
+ * @z_rproc: Remote processor private data
+ * @rpu_mode: mode specified by device tree to configure the RPU to
+ *
+ * set RPU operation mode
+ *
+ * Return: 0 for success, negative value for failure
+ */
+static int r5_set_mode(struct zynqmp_r5_rproc *z_rproc,
+		       enum rpu_oper_mode rpu_mode)
+{
+	enum rpu_tcm_comb tcm_mode;
+	enum rpu_oper_mode cur_rpu_mode;
+	int ret;
+
+	ret = zynqmp_pm_get_rpu_mode(z_rproc->pnode_id, &cur_rpu_mode);
+	if (ret < 0)
+		return ret;
+
+	if (rpu_mode != cur_rpu_mode) {
+		ret = zynqmp_pm_set_rpu_mode(z_rproc->pnode_id,
+					     rpu_mode);
+		if (ret < 0)
+			return ret;
+	}
+
+	tcm_mode = (rpu_mode == PM_RPU_MODE_LOCKSTEP) ?
+		    PM_RPU_TCM_COMB : PM_RPU_TCM_SPLIT;
+	return zynqmp_pm_set_tcm_config(z_rproc->pnode_id, tcm_mode);
+}
+
+/*
+ * zynqmp_r5_rproc_mem_release
+ * @rproc: single R5 core's corresponding rproc instance
+ * @mem: mem entry to unmap
+ *
+ * Unmap SRAM banks when powering down R5 core.
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int sram_mem_release(struct rproc *rproc, struct rproc_mem_entry *mem)
+{
+	struct zynqmp_r5_rproc *z_rproc = rproc->priv;
+	struct device *dev = &rproc->dev;
+	unsigned int i;
+	int ret = 0;
+	struct sram_addr_data *sram_banks = (struct sram_addr_data *)mem->priv;
+	u32 pnode_id, status, usage = 0;
+
+	iounmap(mem->va);
+	/*
+	 * This loop is to go over each bank in sram property.
+	 *
+	 * Note that each of the functions zynqmp_pm_get_node_status and
+	 * zynqmp_pm_release_node will not error out and only report with
+	 * dev_warn as there may be other nodes remaining to attempt to
+	 * power off.
+	 *
+	 * If zynqmp_pm_get_node_status fails, then the subsequent call to
+	 * zynqmp_pm_release_node should also fail so error out in this case.
+	 */
+
+	for (i = 0; i < MAX_BANKS; i++) {
+		pnode_id = sram_banks->ids[i];
+
+		if (!pnode_id)
+			continue;
+
+		if (z_rproc->versal) {
+			/* only request node if not already requested */
+			ret = zynqmp_pm_get_node_status(pnode_id, &status, NULL, &usage);
+			if (ret) {
+				dev_warn(dev, "Unable to get status for node %d\n",
+					 pnode_id);
+				continue;
+			}
+		}
+
+		if (usage || !z_rproc->versal) {
+			ret = zynqmp_pm_release_node(pnode_id);
+			if (ret < 0)
+				dev_warn(dev, "Unable to release node %d\n",
+					 pnode_id);
+		}
+	}
+
+	return ret;
+}
+
+/*
+ * zynqmp_r5_rproc_start
+ * @rproc: single R5 core's corresponding rproc instance
+ *
+ * Start R5 Core from designated boot address.
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int zynqmp_r5_rproc_start(struct rproc *rproc)
+{
+	struct zynqmp_r5_rproc *z_rproc = rproc->priv;
+	enum rpu_boot_mem bootmem;
+	int ret;
+	u32 status;
+
+	bootmem = (rproc->bootaddr & 0xF0000000) == 0xF0000000 ?
+		  PM_RPU_BOOTMEM_HIVEC : PM_RPU_BOOTMEM_LOVEC;
+
+	dev_dbg(rproc->dev.parent, "RPU boot from %s.",
+		bootmem == PM_RPU_BOOTMEM_HIVEC ? "OCM" : "TCM");
+
+	/* If core is already powered on, turn off before re-wake. */
+	ret = zynqmp_pm_get_node_status(z_rproc->pnode_id, &status, NULL, NULL);
+	if (ret)
+		return ret;
+
+	if (status) {
+		ret = zynqmp_pm_force_pwrdwn(z_rproc->pnode_id,
+					     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+		if (ret)
+			return ret;
+	}
+
+	return zynqmp_pm_request_wake(z_rproc->pnode_id, 1,
+				     bootmem, ZYNQMP_PM_REQUEST_ACK_NO);
+}
+
+/*
+ * zynqmp_r5_rproc_stop
+ * @rproc: single R5 core's corresponding rproc instance
+ *
+ * Power down  R5 Core.
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int zynqmp_r5_rproc_stop(struct rproc *rproc)
+{
+	struct zynqmp_r5_rproc *z_rproc = rproc->priv;
+
+	return zynqmp_pm_force_pwrdwn(z_rproc->pnode_id,
+				     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+}
+
+/*
+ * zynqmp_r5_rproc_mem_alloc
+ * @rproc: single R5 core's corresponding rproc instance
+ * @mem: mem entry to map
+ *
+ * Callback to map va for memory-region's carveout.
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int zynqmp_r5_rproc_mem_alloc(struct rproc *rproc,
+				     struct rproc_mem_entry *mem)
+{
+	void *va;
+
+	va = ioremap_wc(mem->dma, mem->len);
+	if (IS_ERR_OR_NULL(va))
+		return -ENOMEM;
+
+	mem->va = va;
+
+	return 0;
+}
+
+/*
+ * zynqmp_r5_rproc_mem_release
+ * @rproc: single R5 core's corresponding rproc instance
+ * @mem: mem entry to unmap
+ *
+ * Unmap memory-region carveout
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int zynqmp_r5_rproc_mem_release(struct rproc *rproc,
+				       struct rproc_mem_entry *mem)
+{
+	iounmap(mem->va);
+	return 0;
+}
+
+/*
+ * parse_mem_regions
+ * @rproc: single R5 core's corresponding rproc instance
+ *
+ * Construct rproc mem carveouts from carveout provided in
+ * memory-region property
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int parse_mem_regions(struct rproc *rproc)
+{
+	int num_mems, i;
+	struct zynqmp_r5_rproc *z_rproc = rproc->priv;
+	struct device *dev = &rproc->dev;
+	struct device_node *np = z_rproc->dev->of_node;
+	struct rproc_mem_entry *mem;
+
+	num_mems = of_count_phandle_with_args(np, DDR_LIST_PROP, NULL);
+	if (num_mems <= 0)
+		return 0;
+
+	for (i = 0; i < num_mems; i++) {
+		struct device_node *node;
+		struct reserved_mem *rmem;
+
+		node = of_parse_phandle(np, DDR_LIST_PROP, i);
+		if (!node)
+			return -EINVAL;
+
+		rmem = of_reserved_mem_lookup(node);
+		if (!rmem)
+			return -EINVAL;
+
+		if (strstr(node->name, "vdev0vring")) {
+			int vring_id;
+			char name[16];
+
+			/*
+			 * expecting form of "rpuXvdev0vringX as documented
+			 * in xilinx remoteproc device tree binding
+			 */
+			if (strlen(node->name) < 15) {
+				dev_err(dev, "%pOF is less than 14 chars",
+					node);
+				of_node_put(node);
+				return -EINVAL;
+			}
+
+			/*
+			 * can be 1 of multiple vring IDs per IPC channel
+			 * e.g. 'vdev0vring0' and 'vdev0vring1'
+			 */
+			vring_id = node->name[14] - '0';
+			snprintf(name, sizeof(name), "vdev0vring%d", vring_id);
+			/* Register vring */
+			mem = rproc_mem_entry_init(dev, NULL,
+						   (dma_addr_t)rmem->base,
+						   rmem->size, rmem->base,
+						   zynqmp_r5_rproc_mem_alloc,
+						   zynqmp_r5_rproc_mem_release,
+						   name);
+		} else {
+			/* Register DMA region */
+			int (*alloc)(struct rproc *r,
+				     struct rproc_mem_entry *rme);
+			int (*release)(struct rproc *r,
+				       struct rproc_mem_entry *rme);
+			char name[20];
+
+			if (strstr(node->name, "vdev0buffer")) {
+				alloc = NULL;
+				release = NULL;
+				strcpy(name, "vdev0buffer");
+			} else {
+				alloc = zynqmp_r5_rproc_mem_alloc;
+				release = zynqmp_r5_rproc_mem_release;
+				strcpy(name, node->name);
+			}
+
+			mem = rproc_mem_entry_init(dev, NULL,
+						   (dma_addr_t)rmem->base,
+						   rmem->size, rmem->base,
+						   alloc, release, name);
+		}
+
+		of_node_put(node);
+
+		if (!mem)
+			return -ENOMEM;
+
+		rproc_add_carveout(rproc, mem);
+	}
+
+	return 0;
+}
+
+/**
+ * zynqmp_r5_pm_request_sram - power up SRAMS for R5.
+ * @dev: Device pointer of rproc instance.
+ * @dt_node: node with power domain to request use for power-on.
+ * @versal: denote whether to use Versal or ZU+ platform IDs
+ * @sram_banks: list of srams associated with carveout
+ * Given sram, attempt to power up the bank with its corresponding Xilinx
+ * Platform Management ID.
+ *
+ * Ensure SRAMs associated with the core are powered on.
+ *
+ * Return: return 0 on success, otherwise non-zero value on failure
+ */
+static int zynqmp_r5_pm_request_sram(struct device *dev,
+				     struct device_node *dt_node, bool versal,
+				     struct sram_addr_data *sram_banks)
+{
+	int ret, index, num_banks, sram_index = 0;
+	u32 pnode_id, status, usage = 0;
+
+	if (!of_get_property(dt_node, PD_PROP, NULL))
+		return -EINVAL;
+
+	num_banks = of_count_phandle_with_args(dt_node, PD_PROP, NULL);
+
+	/*
+	 * As the elements are in the order of:
+	 * <SoC_firmware> <power-domain> ...
+	 * Only use even elements in this list.
+	 *
+	 * Note that each of the functions zynqmp_pm_get_node_status and
+	 * zynqmp_pm_request_node will not error out and only report with
+	 * dev_warn as there may be other nodes remaining to attempt to
+	 * power on.
+	 *
+	 * If zynqmp_pm_get_node_status fails, then the subsequent call to
+	 * zynqmp_pm_request_node should also fail so error out in this case.
+	 */
+	for (index = 1; index < num_banks; index += 2) {
+		of_property_read_u32_index(dt_node, PD_PROP, index, &pnode_id);
+
+		if (versal) {
+			/* only request node if not already requested */
+			ret = zynqmp_pm_get_node_status(pnode_id, &status, NULL,
+							&usage);
+			if (ret) {
+				dev_err(dev, "get status for node %d, %d\n",
+					pnode_id, ret);
+				return ret;
+			}
+		}
+
+		if (!versal || usage == PM_USAGE_NO_MASTER) {
+			ret = zynqmp_pm_request_node(pnode_id,
+						     ZYNQMP_PM_CAPABILITY_ACCESS,
+						     0,
+						     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+			if (ret < 0) {
+				dev_err(dev, "Unable to request node %d\n",
+					pnode_id);
+				return ret;
+			}
+		} else {
+			ret = 0;
+		}
+
+		/* Only have 4 elements in sram_banks so use indices 0-3. */
+		sram_banks->ids[sram_index++] = pnode_id;
+	}
+
+	return 0;
+}
+
+/*
+ * sram_mem_alloc
+ * @rproc: single R5 core's corresponding rproc instance
+ * @mem: mem entry to initialize the va and da fields of
+ *
+ * Given SRAM bank entry,
+ * this callback will set device address for R5 running on TCM
+ * and also setup virtual address for TCM bank remoteproc carveout
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int sram_mem_alloc(struct rproc *rproc, struct rproc_mem_entry *mem)
+{
+	void *va;
+	struct device *dev = rproc->dev.parent;
+
+	va = ioremap_wc(mem->dma, mem->len);
+	if (IS_ERR_OR_NULL(va))
+		return -ENOMEM;
+
+	/* Update memory entry va */
+	mem->va = va;
+
+	va = devm_ioremap_wc(dev, mem->da, mem->len);
+	if (!va)
+		return -ENOMEM;
+	/*
+	 * Handle TCM translation for R5-relative addresses. Here go from
+	 * start of TM0A to end of TCM1B in mapping.
+	 */
+	if (mem->da >= 0xffe00000UL && mem->da < 0xffeb0000UL + 0x10000UL) {
+		/* As R5 is 32 bit, wipe out extra high bits */
+		mem->da &= 0x000fffff;
+		/*
+		 * The R5s expect their TCM banks to be at address 0x0 and 0x2000,
+		 * while on the Linux side they are at 0xffexxxxx. Zero out the high
+		 * 12 bits of the address.
+		 */
+
+		/*
+		 * TCM Banks 1A and 1B (0xffe90000 and 0xffeb0000) still
+		 * need to be translated to 0x0 and 0x20000
+		 */
+		if (mem->da == 0x90000 || mem->da == 0xB0000)
+			mem->da -= 0x90000;
+
+		/* if translated TCM bank address is not valid report error */
+		if (mem->da != 0x0 && mem->da != 0x20000) {
+			dev_err(dev, "invalid TCM bank address: %x\n", mem->da);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * parse_tcm_banks()
+ * @rproc: single R5 core's corresponding rproc instance
+ *
+ * Given R5 node in remoteproc instance
+ * allocate remoteproc carveout for TCM memory
+ * needed for firmware to be loaded
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int parse_tcm_banks(struct rproc *rproc)
+{
+	int i, num_banks, ret = 0;
+	struct zynqmp_r5_rproc *z_rproc = rproc->priv;
+	struct device *dev = &rproc->dev;
+	struct device_node *r5_node = z_rproc->dev->of_node;
+	struct sram_addr_data *sram_banks;
+
+	/* go through TCM banks for r5 node */
+	num_banks = of_count_phandle_with_args(r5_node, BANK_LIST_PROP, NULL);
+	if (num_banks <= 0) {
+		dev_err(dev, "need to specify TCM banks\n");
+		return -EINVAL;
+	}
+	for (i = 0; i < num_banks; i++) {
+		struct resource rsc;
+		resource_size_t size;
+		struct device_node *dt_node;
+		struct rproc_mem_entry *mem;
+		int ret;
+
+		dt_node = of_parse_phandle(r5_node, BANK_LIST_PROP, i);
+		if (!dt_node)
+			return -EINVAL;
+
+		if (of_device_is_available(dt_node)) {
+			ret = of_address_to_resource(dt_node, 0, &rsc);
+			if (ret < 0)
+				return ret;
+
+			size = resource_size(&rsc);
+
+			/*
+			 * This is used later to power off the banks when
+			 * stopping rpu core.
+			 *
+			 * This will be managed as a result of 'devm' so does
+			 * not need a free.
+			 */
+			sram_banks = devm_kzalloc(dev, sizeof(struct sram_addr_data),
+						  GFP_KERNEL);
+			if (!sram_banks) {
+				of_node_put(dt_node);
+				return -ENOMEM;
+			}
+
+			ret = zynqmp_r5_pm_request_sram(dev, dt_node,
+							z_rproc->versal,
+							sram_banks);
+			if (ret < 0) {
+				of_node_put(dt_node);
+				goto error;
+			}
+
+			/* add carveout */
+			mem = rproc_mem_entry_init(dev, NULL, rsc.start,
+						   (int)size, rsc.start,
+						   sram_mem_alloc,
+						   sram_mem_release,
+						   rsc.name);
+			if (!mem)
+				return -ENOMEM;
+
+			mem->priv = (void *)sram_banks;
+			rproc_add_carveout(rproc, mem);
+		}
+		of_node_put(dt_node);
+	}
+	return 0;
+error:
+	return ret;
+}
+
+/*
+ * zynqmp_r5_parse_fw()
+ * @rproc: single R5 core's corresponding rproc instance
+ * @fw: ptr to firmware to be loaded onto r5 core
+ *
+ * When loading firmware, ensure the necessary carveouts are in remoteproc
+ *
+ * return 0 on success, otherwise non-zero value on failure
+ */
+static int zynqmp_r5_parse_fw(struct rproc *rproc, const struct firmware *fw)
+{
+	int ret;
+
+	ret = parse_tcm_banks(rproc);
+	if (ret)
+		return ret;
+
+	ret = parse_mem_regions(rproc);
+	if (ret)
+		return ret;
+
+	ret = rproc_elf_load_rsc_table(rproc, fw);
+	if (ret == -EINVAL) {
+		/*
+		 * resource table only required for IPC.
+		 * if not present, this is not necessarily an error;
+		 * for example, loading r5 hello world application
+		 * so simply inform user and keep going.
+		 */
+		dev_info(&rproc->dev, "no resource table found.\n");
+		ret = 0;
+	}
+	return ret;
+}
+
+/*
+ * zynqmp_r5_rproc_kick() - kick a firmware if mbox is provided
+ * @rproc: r5 core's corresponding rproc structure
+ * @vqid: virtqueue ID
+ */
+static void zynqmp_r5_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct sk_buff *skb = NULL;
+	unsigned int skb_len = 0;
+	struct zynqmp_ipi_message *mb_msg = NULL;
+	int ret = 0;
+
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_rproc *z_rproc = rproc->priv;
+
+	if (of_property_read_bool(dev->of_node, "mboxes")) {
+		skb_len = (unsigned int)(sizeof(vqid) + sizeof(mb_msg));
+		skb = alloc_skb(skb_len, GFP_ATOMIC);
+		if (!skb)
+			return;
+
+		mb_msg = (struct zynqmp_ipi_message *)skb_put(skb, skb_len);
+		mb_msg->len = sizeof(vqid);
+		memcpy(mb_msg->data, &vqid, sizeof(vqid));
+
+		skb_queue_tail(&z_rproc->tx_mc_skbs, skb);
+		ret = mbox_send_message(z_rproc->tx_chan, mb_msg);
+		if (ret < 0) {
+			dev_warn(dev, "Failed to kick remote.\n");
+			skb_dequeue_tail(&z_rproc->tx_mc_skbs);
+			kfree_skb(skb);
+		}
+	} else {
+		(void)skb;
+		(void)skb_len;
+		(void)mb_msg;
+		(void)ret;
+		(void)vqid;
+	}
+}
+
+static struct rproc_ops zynqmp_r5_rproc_ops = {
+	.start		= zynqmp_r5_rproc_start,
+	.stop		= zynqmp_r5_rproc_stop,
+	.load		= rproc_elf_load_segments,
+	.parse_fw	= zynqmp_r5_parse_fw,
+	.find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
+	.sanity_check	= rproc_elf_sanity_check,
+	.get_boot_addr	= rproc_elf_get_boot_addr,
+	.kick		= zynqmp_r5_rproc_kick,
+};
+
+/**
+ * event_notified_idr_cb() - event notified idr callback
+ * @id: idr id
+ * @ptr: pointer to idr private data
+ * @data: data passed to idr_for_each callback
+ *
+ * Pass notification to remoteproc virtio
+ *
+ * Return: 0. having return is to satisfy the idr_for_each() function
+ *          pointer input argument requirement.
+ **/
+static int event_notified_idr_cb(int id, void *ptr, void *data)
+{
+	struct rproc *rproc = data;
+
+	(void)rproc_vq_interrupt(rproc, id);
+	return 0;
+}
+
+/**
+ * handle_event_notified() - remoteproc notification work function
+ * @work: pointer to the work structure
+ *
+ * It checks each registered remoteproc notify IDs.
+ */
+static void handle_event_notified(struct work_struct *work)
+{
+	struct rproc *rproc;
+	struct zynqmp_r5_rproc *z_rproc;
+
+	z_rproc = container_of(work, struct zynqmp_r5_rproc, mbox_work);
+
+	(void)mbox_send_message(z_rproc->rx_chan, NULL);
+	rproc = z_rproc->rproc;
+	/*
+	 * We only use IPI for interrupt. The firmware side may or may
+	 * not write the notifyid when it trigger IPI.
+	 * And thus, we scan through all the registered notifyids.
+	 */
+	idr_for_each(&rproc->notifyids, event_notified_idr_cb, rproc);
+}
+
+/**
+ * zynqmp_r5_mb_rx_cb() - Receive channel mailbox callback
+ * @cl: mailbox client
+ * @msg: message pointer
+ *
+ * It will schedule the R5 notification work.
+ */
+static void zynqmp_r5_mb_rx_cb(struct mbox_client *cl, void *msg)
+{
+	struct zynqmp_r5_rproc *z_rproc;
+
+	z_rproc = container_of(cl, struct zynqmp_r5_rproc, rx_mc);
+	if (msg) {
+		struct zynqmp_ipi_message *ipi_msg, *buf_msg;
+		size_t len;
+
+		ipi_msg = (struct zynqmp_ipi_message *)msg;
+		buf_msg = (struct zynqmp_ipi_message *)z_rproc->rx_mc_buf;
+		len = (ipi_msg->len >= IPI_BUF_LEN_MAX) ?
+		      IPI_BUF_LEN_MAX : ipi_msg->len;
+		buf_msg->len = len;
+		memcpy(buf_msg->data, ipi_msg->data, len);
+	}
+	schedule_work(&z_rproc->mbox_work);
+}
+
+/**
+ * zynqmp_r5_mb_tx_done() - Request has been sent to the remote
+ * @cl: mailbox client
+ * @msg: pointer to the message which has been sent
+ * @r: status of last TX - OK or error
+ *
+ * It will be called by the mailbox framework when the last TX has done.
+ */
+static void zynqmp_r5_mb_tx_done(struct mbox_client *cl, void *msg, int r)
+{
+	struct zynqmp_r5_rproc *z_rproc;
+	struct sk_buff *skb;
+
+	if (!msg)
+		return;
+	z_rproc = container_of(cl, struct zynqmp_r5_rproc, tx_mc);
+	skb = skb_dequeue(&z_rproc->tx_mc_skbs);
+	kfree_skb(skb);
+}
+
+/**
+ * zynqmp_r5_setup_mbox() - Setup mailboxes
+ *			    this is used for each individual R5 core
+ *
+ * @z_rproc: pointer to the ZynqMP R5 processor platform data
+ * @node: pointer of the device node
+ *
+ * Function to setup mailboxes to talk to RPU.
+ *
+ * Return: 0 for success, negative value for failure.
+ */
+static int zynqmp_r5_setup_mbox(struct zynqmp_r5_rproc *z_rproc,
+				struct device_node *node)
+{
+	struct mbox_client *mclient;
+
+	/* Setup TX mailbox channel client */
+	mclient = &z_rproc->tx_mc;
+	mclient->rx_callback = NULL;
+	mclient->tx_block = false;
+	mclient->knows_txdone = false;
+	mclient->tx_done = zynqmp_r5_mb_tx_done;
+	mclient->dev = z_rproc->dev;
+
+	/* Setup TX mailbox channel client */
+	mclient = &z_rproc->rx_mc;
+	mclient->dev = z_rproc->dev;
+	mclient->rx_callback = zynqmp_r5_mb_rx_cb;
+	mclient->tx_block = false;
+	mclient->knows_txdone = false;
+
+	INIT_WORK(&z_rproc->mbox_work, handle_event_notified);
+
+	/* Request TX and RX channels */
+	z_rproc->tx_chan = mbox_request_channel_byname(&z_rproc->tx_mc, "tx");
+	if (IS_ERR(z_rproc->tx_chan)) {
+		dev_err(z_rproc->dev, "failed to request mbox tx channel.\n");
+		z_rproc->tx_chan = NULL;
+		return -EINVAL;
+	}
+
+	z_rproc->rx_chan = mbox_request_channel_byname(&z_rproc->rx_mc, "rx");
+	if (IS_ERR(z_rproc->rx_chan)) {
+		dev_err(z_rproc->dev, "failed to request mbox rx channel.\n");
+		z_rproc->rx_chan = NULL;
+		return -EINVAL;
+	}
+	skb_queue_head_init(&z_rproc->tx_mc_skbs);
+
+	return 0;
+}
+
+/**
+ * zynqmp_r5_probe() - Probes ZynqMP R5 processor device node
+ *		       this is called for each individual R5 core to
+ *		       set up mailbox, Xilinx platform manager unique ID,
+ *		       add to rproc core
+ *
+ * @pdev: domain platform device for current R5 core
+ * @node: pointer of the device node for current R5 core
+ * @rpu_mode: mode to configure RPU, split or lockstep
+ * @data: structure to hold SoC specific data
+ * @z_rproc: Xilinx specific remoteproc structure used later to link
+ *           in to cluster of cores
+ *
+ * Return: 0 for success, negative value for failure.
+ */
+static int zynqmp_r5_probe(struct platform_device *pdev,
+			   struct device_node *node,
+			   enum rpu_oper_mode rpu_mode,
+			   const struct xlnx_r5_data *data,
+			   struct zynqmp_r5_rproc **z_rproc)
+{
+	int ret, r5_entries, pnode_id;
+	struct device *dev = &pdev->dev;
+	struct rproc *rproc_ptr;
+
+	/* Allocate remoteproc instance */
+	rproc_ptr = devm_rproc_alloc(dev, dev_name(dev), &zynqmp_r5_rproc_ops,
+				     NULL, sizeof(struct zynqmp_r5_rproc));
+	if (!rproc_ptr) {
+		ret = -ENOMEM;
+		goto error;
+	}
+
+	rproc_ptr->auto_boot = false;
+	*z_rproc = rproc_ptr->priv;
+	(*z_rproc)->rproc = rproc_ptr;
+	(*z_rproc)->dev = dev;
+	/* Set up DMA mask */
+	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	if (ret)
+		goto error;
+
+	if (!of_get_property(node, PD_PROP, NULL)) {
+		ret = -EINVAL;
+		goto error;
+	}
+
+	/* expect 2 elements for RPU power-domain */
+	r5_entries = of_count_phandle_with_args(node, PD_PROP, NULL);
+	if (r5_entries < 2) {
+		ret = -EINVAL;
+		goto error;
+	}
+
+	/*
+	 * Get R5 power domain node. As the elements are in the order of:
+	 * SoC_firmware power-domain ...
+	 * Only use every other element in this list.
+	 */
+	of_property_read_u32_index(node, PD_PROP, 1U, &pnode_id);
+	(*z_rproc)->pnode_id = pnode_id;
+
+	(*z_rproc)->versal = data->versal_soc;
+
+	ret = r5_set_mode(*z_rproc, rpu_mode);
+	if (ret)
+		goto error;
+
+	if (of_property_read_bool(node, "mboxes")) {
+		ret = zynqmp_r5_setup_mbox(*z_rproc, node);
+		if (ret)
+			goto error;
+	}
+
+	/* Add R5 remoteproc */
+	ret = devm_rproc_add(dev, rproc_ptr);
+	if (ret)
+		goto error;
+
+	/*
+	 * In Versal SoC, the Xilinx platform management firmware will power
+	 * off the R5 cores if they are not requested. In this case, this call
+	 * notifies Xilinx platform management firmware that the R5 core will
+	 * be used and should be powered on.
+	 *
+	 * On ZynqMP platform this is not needed as the R5 cores are not
+	 * powered off by default.
+	 */
+	if ((*z_rproc)->versal) {
+		ret = zynqmp_pm_request_node((*z_rproc)->pnode_id,
+					     ZYNQMP_PM_CAPABILITY_ACCESS, 0,
+					     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+		if (ret < 0)
+			goto error;
+	}
+
+	return 0;
+error:
+	*z_rproc = NULL;
+	return ret;
+}
+
+/*
+ * zynqmp_r5_remoteproc_probe()
+ *
+ * @pdev: domain platform device for R5 cluster
+ *
+ * called when driver is probed, for each R5 core specified in DT,
+ * setup as needed to do remoteproc-related operations
+ *
+ * Return: 0 for success, negative value for failure.
+ */
+static int zynqmp_r5_remoteproc_probe(struct platform_device *pdev)
+{
+	int ret, core_count;
+	struct device *dev = &pdev->dev;
+	struct device_node *nc;
+	enum rpu_oper_mode rpu_mode = PM_RPU_MODE_LOCKSTEP;
+	struct list_head *cluster; /* list to track each core's rproc */
+	struct zynqmp_r5_rproc *z_rproc = NULL;
+	struct platform_device *child_pdev;
+	struct list_head *pos;
+	const struct xlnx_r5_data *data;
+
+	ret = of_property_read_u32(dev->of_node, "xlnx,cluster-mode", &rpu_mode);
+	if (ret < 0 || (rpu_mode != PM_RPU_MODE_LOCKSTEP &&
+			rpu_mode != PM_RPU_MODE_SPLIT)) {
+		dev_err(dev, "invalid format cluster mode: ret %d mode %x\n",
+			ret, rpu_mode);
+		return ret;
+	}
+
+	dev_dbg(dev, "RPU configuration: %s\n",
+		rpu_mode == PM_RPU_MODE_LOCKSTEP ? "lockstep" : "split");
+
+	/*
+	 * if 2 RPUs provided but one is lockstep, then we have an
+	 * invalid configuration.
+	 */
+
+	core_count = of_get_available_child_count(dev->of_node);
+	if ((rpu_mode == PM_RPU_MODE_LOCKSTEP && core_count != 1) ||
+	    core_count > MAX_RPROCS)
+		return -EINVAL;
+
+	cluster = devm_kzalloc(dev, sizeof(*cluster), GFP_KERNEL);
+	if (!cluster)
+		return -ENOMEM;
+	INIT_LIST_HEAD(cluster);
+
+	ret = devm_of_platform_populate(dev);
+	if (ret) {
+		dev_err(dev, "devm_of_platform_populate failed, ret = %d\n",
+			ret);
+		return ret;
+	}
+
+	/*
+	 * SoC specific information. For now, just flag to determine if
+	 * on versal platform for node management.
+	 */
+	data = of_device_get_match_data(&pdev->dev);
+	if (!data) {
+		dev_err(dev, "SoC-specific data is not defined\n");
+		return -ENODEV;
+	}
+
+	/* probe each individual r5 core's remoteproc-related info */
+	for_each_available_child_of_node(dev->of_node, nc) {
+		child_pdev = of_find_device_by_node(nc);
+		if (!child_pdev) {
+			dev_err(dev, "could not get R5 core platform device\n");
+			ret = -ENODEV;
+			goto out;
+		}
+		ret = zynqmp_r5_probe(child_pdev, nc, rpu_mode, data,
+				      &z_rproc);
+		dev_dbg(dev, "%s to probe rpu %pOF\n",
+			ret ? "Failed" : "Able",
+			nc);
+		if (!z_rproc)
+			ret = -EINVAL;
+		if (ret) {
+			put_device(&child_pdev->dev);
+			goto out;
+		}
+
+		list_add_tail(&z_rproc->elem, cluster);
+		put_device(&child_pdev->dev);
+	}
+	/* wire in so each core can be cleaned up at driver remove */
+	platform_set_drvdata(pdev, cluster);
+	return 0;
+out:
+	/*
+	 * undo core0 upon any failures on core1 in split-mode
+	 *
+	 * in zynqmp_r5_probe z_rproc is set to null
+	 * and ret to non-zero value if error
+	 */
+	if (ret && !z_rproc && rpu_mode == PM_RPU_MODE_SPLIT &&
+	    !list_empty(cluster)) {
+		list_for_each(pos, cluster) {
+			z_rproc = list_entry(pos, struct zynqmp_r5_rproc, elem);
+			if (of_property_read_bool(z_rproc->dev->of_node, "mboxes")) {
+				mbox_free_channel(z_rproc->tx_chan);
+				mbox_free_channel(z_rproc->rx_chan);
+			}
+		}
+	}
+	return ret;
+}
+
+/*
+ * zynqmp_r5_remoteproc_remove()
+ *
+ * @pdev: domain platform device for R5 cluster
+ *
+ * When the driver is unloaded, clean up the mailboxes for each
+ * remoteproc that was initially probed.
+ */
+static int zynqmp_r5_remoteproc_remove(struct platform_device *pdev)
+{
+	struct list_head *pos, *temp, *cluster = (struct list_head *)
+						 platform_get_drvdata(pdev);
+	struct zynqmp_r5_rproc *z_rproc = NULL;
+
+	list_for_each_safe(pos, temp, cluster) {
+		z_rproc = list_entry(pos, struct zynqmp_r5_rproc, elem);
+
+		/*
+		 * For Versal platform, the Xilinx platform management
+		 * firmware needs to have a release call to match the
+		 * corresponding reque in order to power down the core.
+		 */
+		if (z_rproc->versal)
+			zynqmp_pm_release_node(z_rproc->pnode_id);
+
+		if (of_property_read_bool(z_rproc->dev->of_node, "mboxes")) {
+			mbox_free_channel(z_rproc->tx_chan);
+			mbox_free_channel(z_rproc->rx_chan);
+		}
+		list_del(pos);
+	}
+	return 0;
+}
+
+static const struct xlnx_r5_data versal_data = {
+	.versal_soc = true,
+};
+
+static const struct xlnx_r5_data zynqmp_data = {
+	.versal_soc = false,
+};
+
+static const struct of_device_id xilinx_r5_of_match[] = {
+	{ .compatible = "xlnx,zynqmp-r5-remoteproc", .data = &zynqmp_data, },
+	{ .compatible = "xlnx,versal-r5-remoteproc", .data = &versal_data, },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, xilinx_r5_of_match);
+
+/* Match table for OF platform binding */
+static struct platform_driver zynqmp_r5_remoteproc_driver = {
+	.probe = zynqmp_r5_remoteproc_probe,
+	.remove = zynqmp_r5_remoteproc_remove,
+	.driver = {
+		.name = "zynqmp_r5_remoteproc",
+		.of_match_table = xilinx_r5_of_match,
+	},
+};
+module_platform_driver(zynqmp_r5_remoteproc_driver);
+
+MODULE_AUTHOR("Ben Levinsky <ben.levinsky@xilinx.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/Kconfig
@@ -201,7 +201,7 @@
 
 config RESET_SIMPLE
 	bool "Simple Reset Controller Driver" if COMPILE_TEST
-	default ARCH_ASPEED || ARCH_BCM4908 || ARCH_BITMAIN || ARCH_REALTEK || ARCH_STM32 || (ARCH_INTEL_SOCFPGA && ARM64) || ARCH_SUNXI || ARC
+	default ARCH_ASPEED || ARCH_BCM4908 || ARCH_BITMAIN || ARCH_REALTEK || ARCH_STM32 || (ARCH_INTEL_SOCFPGA && ARM64) || ARCH_SUNXI || ARC || RISCV
 	help
 	  This enables a simple reset controller driver for reset lines that
 	  that can be asserted and deasserted by toggling bits in a contiguous,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/core.c
@@ -806,6 +806,9 @@
 {
 	lockdep_assert_held(&reset_list_mutex);
 
+	if (IS_ERR_OR_NULL(rstc))
+		return;
+
 	kref_put(&rstc->refcnt, __reset_control_release);
 }
 
@@ -1016,11 +1019,8 @@
 void reset_control_bulk_put(int num_rstcs, struct reset_control_bulk_data *rstcs)
 {
 	mutex_lock(&reset_list_mutex);
-	while (num_rstcs--) {
-		if (IS_ERR_OR_NULL(rstcs[num_rstcs].rstc))
-			continue;
+	while (num_rstcs--)
 		__reset_control_put_internal(rstcs[num_rstcs].rstc);
-	}
 	mutex_unlock(&reset_list_mutex);
 }
 EXPORT_SYMBOL_GPL(reset_control_bulk_put);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/hisilicon/hi6220_reset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/hisilicon/hi6220_reset.c
@@ -164,7 +164,7 @@
 	if (!data)
 		return -ENOMEM;
 
-	type = (enum hi6220_reset_ctrl_type)of_device_get_match_data(dev);
+	type = (uintptr_t)of_device_get_match_data(dev);
 
 	regmap = syscon_node_to_regmap(np);
 	if (IS_ERR(regmap)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/reset-berlin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/reset-berlin.c
@@ -68,13 +68,14 @@
 
 static int berlin2_reset_probe(struct platform_device *pdev)
 {
-	struct device_node *parent_np = of_get_parent(pdev->dev.of_node);
+	struct device_node *parent_np;
 	struct berlin_reset_priv *priv;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
 
+	parent_np = of_get_parent(pdev->dev.of_node);
 	priv->regmap = syscon_node_to_regmap(parent_np);
 	of_node_put(parent_np);
 	if (IS_ERR(priv->regmap))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/reset-imx7.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/reset-imx7.c
@@ -329,6 +329,7 @@
 		break;
 
 	case IMX8MP_RESET_PCIE_CTRL_APPS_EN:
+	case IMX8MP_RESET_PCIEPHY_PERST:
 		value = assert ? 0 : bit;
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/reset-k210.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/reset-k210.c
@@ -91,7 +91,7 @@
 static int k210_rst_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	struct device_node *parent_np = of_get_parent(dev->of_node);
+	struct device_node *parent_np;
 	struct k210_rst *ksr;
 
 	dev_info(dev, "K210 reset controller\n");
@@ -100,6 +100,7 @@
 	if (!ksr)
 		return -ENOMEM;
 
+	parent_np = of_get_parent(dev->of_node);
 	ksr->map = syscon_node_to_regmap(parent_np);
 	of_node_put(parent_np);
 	if (IS_ERR(ksr->map))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/reset-rzg2l-usbphy-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/reset-rzg2l-usbphy-ctrl.c
@@ -121,7 +121,9 @@
 		return dev_err_probe(dev, PTR_ERR(priv->rstc),
 				     "failed to get reset\n");
 
-	reset_control_deassert(priv->rstc);
+	error = reset_control_deassert(priv->rstc);
+	if (error)
+		return error;
 
 	priv->rcdev.ops = &rzg2l_usbphy_ctrl_reset_ops;
 	priv->rcdev.of_reset_n_cells = 1;
@@ -137,7 +139,12 @@
 	dev_set_drvdata(dev, priv);
 
 	pm_runtime_enable(&pdev->dev);
-	pm_runtime_resume_and_get(&pdev->dev);
+	error = pm_runtime_resume_and_get(&pdev->dev);
+	if (error < 0) {
+		pm_runtime_disable(&pdev->dev);
+		reset_control_assert(priv->rstc);
+		return dev_err_probe(&pdev->dev, error, "pm_runtime_resume_and_get failed");
+	}
 
 	/* put pll and phy into reset state */
 	spin_lock_irqsave(&priv->lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/reset/reset-uniphier-glue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/reset/reset-uniphier-glue.c
@@ -23,7 +23,7 @@
 
 struct uniphier_glue_reset_priv {
 	struct clk_bulk_data clk[MAX_CLKS];
-	struct reset_control *rst[MAX_RSTS];
+	struct reset_control_bulk_data rst[MAX_RSTS];
 	struct reset_simple_data rdata;
 	const struct uniphier_glue_reset_soc_data *data;
 };
@@ -33,9 +33,7 @@
 	struct device *dev = &pdev->dev;
 	struct uniphier_glue_reset_priv *priv;
 	struct resource *res;
-	resource_size_t size;
-	const char *name;
-	int i, ret, nr;
+	int i, ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -47,7 +45,6 @@
 		return -EINVAL;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	size = resource_size(res);
 	priv->rdata.membase = devm_ioremap_resource(dev, res);
 	if (IS_ERR(priv->rdata.membase))
 		return PTR_ERR(priv->rdata.membase);
@@ -58,26 +55,24 @@
 	if (ret)
 		return ret;
 
-	for (i = 0; i < priv->data->nrsts; i++) {
-		name = priv->data->reset_names[i];
-		priv->rst[i] = devm_reset_control_get_shared(dev, name);
-		if (IS_ERR(priv->rst[i]))
-			return PTR_ERR(priv->rst[i]);
-	}
+	for (i = 0; i < priv->data->nrsts; i++)
+		priv->rst[i].id = priv->data->reset_names[i];
+	ret = devm_reset_control_bulk_get_shared(dev, priv->data->nrsts,
+						 priv->rst);
+	if (ret)
+		return ret;
 
 	ret = clk_bulk_prepare_enable(priv->data->nclks, priv->clk);
 	if (ret)
 		return ret;
 
-	for (nr = 0; nr < priv->data->nrsts; nr++) {
-		ret = reset_control_deassert(priv->rst[nr]);
-		if (ret)
-			goto out_rst_assert;
-	}
+	ret = reset_control_bulk_deassert(priv->data->nrsts, priv->rst);
+	if (ret)
+		goto out_clk_disable;
 
 	spin_lock_init(&priv->rdata.lock);
 	priv->rdata.rcdev.owner = THIS_MODULE;
-	priv->rdata.rcdev.nr_resets = size * BITS_PER_BYTE;
+	priv->rdata.rcdev.nr_resets = resource_size(res) * BITS_PER_BYTE;
 	priv->rdata.rcdev.ops = &reset_simple_ops;
 	priv->rdata.rcdev.of_node = dev->of_node;
 	priv->rdata.active_low = true;
@@ -91,9 +86,9 @@
 	return 0;
 
 out_rst_assert:
-	while (nr--)
-		reset_control_assert(priv->rst[nr]);
+	reset_control_bulk_assert(priv->data->nrsts, priv->rst);
 
+out_clk_disable:
 	clk_bulk_disable_unprepare(priv->data->nclks, priv->clk);
 
 	return ret;
@@ -102,10 +97,8 @@
 static int uniphier_glue_reset_remove(struct platform_device *pdev)
 {
 	struct uniphier_glue_reset_priv *priv = platform_get_drvdata(pdev);
-	int i;
 
-	for (i = 0; i < priv->data->nrsts; i++)
-		reset_control_assert(priv->rst[i]);
+	reset_control_bulk_assert(priv->data->nrsts, priv->rst);
 
 	clk_bulk_disable_unprepare(priv->data->nclks, priv->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/mtk_rpmsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/mtk_rpmsg.c
@@ -234,7 +234,9 @@
 		if (info->registered)
 			continue;
 
+		mutex_unlock(&subdev->channels_lock);
 		ret = mtk_rpmsg_register_device(subdev, &info->info);
+		mutex_lock(&subdev->channels_lock);
 		if (ret) {
 			dev_err(&pdev->dev, "Can't create rpmsg_device\n");
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/qcom_glink_native.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/qcom_glink_native.c
@@ -92,6 +92,8 @@
  * @rcids:	idr of all channels with a known remote channel id
  * @features:	remote features
  * @intentless:	flag to indicate that there is no intent
+ * @tx_avail_notify: Waitqueue for pending tx tasks
+ * @sent_read_notify: flag to check cmd sent or not
  */
 struct qcom_glink {
 	struct device *dev;
@@ -118,6 +120,8 @@
 	unsigned long features;
 
 	bool intentless;
+	wait_queue_head_t tx_avail_notify;
+	bool sent_read_notify;
 };
 
 enum {
@@ -187,20 +191,20 @@
 
 static const struct rpmsg_endpoint_ops glink_endpoint_ops;
 
-#define RPM_CMD_VERSION			0
-#define RPM_CMD_VERSION_ACK		1
-#define RPM_CMD_OPEN			2
-#define RPM_CMD_CLOSE			3
-#define RPM_CMD_OPEN_ACK		4
-#define RPM_CMD_INTENT			5
-#define RPM_CMD_RX_DONE			6
-#define RPM_CMD_RX_INTENT_REQ		7
-#define RPM_CMD_RX_INTENT_REQ_ACK	8
-#define RPM_CMD_TX_DATA			9
-#define RPM_CMD_CLOSE_ACK		11
-#define RPM_CMD_TX_DATA_CONT		12
-#define RPM_CMD_READ_NOTIF		13
-#define RPM_CMD_RX_DONE_W_REUSE		14
+#define GLINK_CMD_VERSION		0
+#define GLINK_CMD_VERSION_ACK		1
+#define GLINK_CMD_OPEN			2
+#define GLINK_CMD_CLOSE			3
+#define GLINK_CMD_OPEN_ACK		4
+#define GLINK_CMD_INTENT		5
+#define GLINK_CMD_RX_DONE		6
+#define GLINK_CMD_RX_INTENT_REQ		7
+#define GLINK_CMD_RX_INTENT_REQ_ACK	8
+#define GLINK_CMD_TX_DATA		9
+#define GLINK_CMD_CLOSE_ACK		11
+#define GLINK_CMD_TX_DATA_CONT		12
+#define GLINK_CMD_READ_NOTIF		13
+#define GLINK_CMD_RX_DONE_W_REUSE	14
 
 #define GLINK_FEATURE_INTENTLESS	BIT(1)
 
@@ -222,6 +226,10 @@
 
 	channel->glink = glink;
 	channel->name = kstrdup(name, GFP_KERNEL);
+	if (!channel->name) {
+		kfree(channel);
+		return ERR_PTR(-ENOMEM);
+	}
 
 	init_completion(&channel->open_req);
 	init_completion(&channel->open_ack);
@@ -301,6 +309,20 @@
 	glink->tx_pipe->write(glink->tx_pipe, hdr, hlen, data, dlen);
 }
 
+static void qcom_glink_send_read_notify(struct qcom_glink *glink)
+{
+	struct glink_msg msg;
+
+	msg.cmd = cpu_to_le16(GLINK_CMD_READ_NOTIF);
+	msg.param1 = 0;
+	msg.param2 = 0;
+
+	qcom_glink_tx_write(glink, &msg, sizeof(msg), NULL, 0);
+
+	mbox_send_message(glink->mbox_chan, NULL);
+	mbox_client_txdone(glink->mbox_chan, 0);
+}
+
 static int qcom_glink_tx(struct qcom_glink *glink,
 			 const void *hdr, size_t hlen,
 			 const void *data, size_t dlen, bool wait)
@@ -321,12 +343,21 @@
 			goto out;
 		}
 
+		if (!glink->sent_read_notify) {
+			glink->sent_read_notify = true;
+			qcom_glink_send_read_notify(glink);
+		}
+
 		/* Wait without holding the tx_lock */
 		spin_unlock_irqrestore(&glink->tx_lock, flags);
 
-		usleep_range(10000, 15000);
+		wait_event_timeout(glink->tx_avail_notify,
+				   qcom_glink_tx_avail(glink) >= tlen, 10 * HZ);
 
 		spin_lock_irqsave(&glink->tx_lock, flags);
+
+		if (qcom_glink_tx_avail(glink) >= tlen)
+			glink->sent_read_notify = false;
 	}
 
 	qcom_glink_tx_write(glink, hdr, hlen, data, dlen);
@@ -344,7 +375,7 @@
 {
 	struct glink_msg msg;
 
-	msg.cmd = cpu_to_le16(RPM_CMD_VERSION);
+	msg.cmd = cpu_to_le16(GLINK_CMD_VERSION);
 	msg.param1 = cpu_to_le16(GLINK_VERSION_1);
 	msg.param2 = cpu_to_le32(glink->features);
 
@@ -355,7 +386,7 @@
 {
 	struct glink_msg msg;
 
-	msg.cmd = cpu_to_le16(RPM_CMD_VERSION_ACK);
+	msg.cmd = cpu_to_le16(GLINK_CMD_VERSION_ACK);
 	msg.param1 = cpu_to_le16(GLINK_VERSION_1);
 	msg.param2 = cpu_to_le32(glink->features);
 
@@ -367,7 +398,7 @@
 {
 	struct glink_msg msg;
 
-	msg.cmd = cpu_to_le16(RPM_CMD_OPEN_ACK);
+	msg.cmd = cpu_to_le16(GLINK_CMD_OPEN_ACK);
 	msg.param1 = cpu_to_le16(channel->rcid);
 	msg.param2 = cpu_to_le32(0);
 
@@ -393,11 +424,11 @@
 }
 
 /**
- * qcom_glink_send_open_req() - send a RPM_CMD_OPEN request to the remote
+ * qcom_glink_send_open_req() - send a GLINK_CMD_OPEN request to the remote
  * @glink: Ptr to the glink edge
  * @channel: Ptr to the channel that the open req is sent
  *
- * Allocates a local channel id and sends a RPM_CMD_OPEN message to the remote.
+ * Allocates a local channel id and sends a GLINK_CMD_OPEN message to the remote.
  * Will return with refcount held, regardless of outcome.
  *
  * Returns 0 on success, negative errno otherwise.
@@ -426,7 +457,7 @@
 
 	channel->lcid = ret;
 
-	req.msg.cmd = cpu_to_le16(RPM_CMD_OPEN);
+	req.msg.cmd = cpu_to_le16(GLINK_CMD_OPEN);
 	req.msg.param1 = cpu_to_le16(channel->lcid);
 	req.msg.param2 = cpu_to_le32(name_len);
 	strcpy(req.name, channel->name);
@@ -451,7 +482,7 @@
 {
 	struct glink_msg req;
 
-	req.cmd = cpu_to_le16(RPM_CMD_CLOSE);
+	req.cmd = cpu_to_le16(GLINK_CMD_CLOSE);
 	req.param1 = cpu_to_le16(channel->lcid);
 	req.param2 = 0;
 
@@ -463,7 +494,7 @@
 {
 	struct glink_msg req;
 
-	req.cmd = cpu_to_le16(RPM_CMD_CLOSE_ACK);
+	req.cmd = cpu_to_le16(GLINK_CMD_CLOSE_ACK);
 	req.param1 = cpu_to_le16(rcid);
 	req.param2 = 0;
 
@@ -494,7 +525,7 @@
 		iid = intent->id;
 		reuse = intent->reuse;
 
-		cmd.id = reuse ? RPM_CMD_RX_DONE_W_REUSE : RPM_CMD_RX_DONE;
+		cmd.id = reuse ? GLINK_CMD_RX_DONE_W_REUSE : GLINK_CMD_RX_DONE;
 		cmd.lcid = cid;
 		cmd.liid = iid;
 
@@ -606,7 +637,7 @@
 {
 	struct glink_msg msg;
 
-	msg.cmd = cpu_to_le16(RPM_CMD_RX_INTENT_REQ_ACK);
+	msg.cmd = cpu_to_le16(GLINK_CMD_RX_INTENT_REQ_ACK);
 	msg.param1 = cpu_to_le16(channel->lcid);
 	msg.param2 = cpu_to_le32(granted);
 
@@ -637,7 +668,7 @@
 	} __packed;
 	struct command cmd;
 
-	cmd.id = cpu_to_le16(RPM_CMD_INTENT);
+	cmd.id = cpu_to_le16(GLINK_CMD_INTENT);
 	cmd.lcid = cpu_to_le16(channel->lcid);
 	cmd.count = cpu_to_le32(1);
 	cmd.size = cpu_to_le32(intent->size);
@@ -929,6 +960,7 @@
 	spin_unlock_irqrestore(&glink->idr_lock, flags);
 	if (!channel) {
 		dev_err(glink->dev, "intents for non-existing channel\n");
+		qcom_glink_rx_advance(glink, ALIGN(msglen, 8));
 		return;
 	}
 
@@ -986,6 +1018,9 @@
 	unsigned int cmd;
 	int ret = 0;
 
+	/* To wakeup any blocking writers */
+	wake_up_all(&glink->tx_avail_notify);
+
 	for (;;) {
 		avail = qcom_glink_rx_avail(glink);
 		if (avail < sizeof(msg))
@@ -998,42 +1033,43 @@
 		param2 = le32_to_cpu(msg.param2);
 
 		switch (cmd) {
-		case RPM_CMD_VERSION:
-		case RPM_CMD_VERSION_ACK:
-		case RPM_CMD_CLOSE:
-		case RPM_CMD_CLOSE_ACK:
-		case RPM_CMD_RX_INTENT_REQ:
+		case GLINK_CMD_VERSION:
+		case GLINK_CMD_VERSION_ACK:
+		case GLINK_CMD_CLOSE:
+		case GLINK_CMD_CLOSE_ACK:
+		case GLINK_CMD_RX_INTENT_REQ:
 			ret = qcom_glink_rx_defer(glink, 0);
 			break;
-		case RPM_CMD_OPEN_ACK:
+		case GLINK_CMD_OPEN_ACK:
 			ret = qcom_glink_rx_open_ack(glink, param1);
 			qcom_glink_rx_advance(glink, ALIGN(sizeof(msg), 8));
 			break;
-		case RPM_CMD_OPEN:
-			ret = qcom_glink_rx_defer(glink, param2);
+		case GLINK_CMD_OPEN:
+			/* upper 16 bits of param2 are the "prio" field */
+			ret = qcom_glink_rx_defer(glink, param2 & 0xffff);
 			break;
-		case RPM_CMD_TX_DATA:
-		case RPM_CMD_TX_DATA_CONT:
+		case GLINK_CMD_TX_DATA:
+		case GLINK_CMD_TX_DATA_CONT:
 			ret = qcom_glink_rx_data(glink, avail);
 			break;
-		case RPM_CMD_READ_NOTIF:
+		case GLINK_CMD_READ_NOTIF:
 			qcom_glink_rx_advance(glink, ALIGN(sizeof(msg), 8));
 
 			mbox_send_message(glink->mbox_chan, NULL);
 			mbox_client_txdone(glink->mbox_chan, 0);
 			break;
-		case RPM_CMD_INTENT:
+		case GLINK_CMD_INTENT:
 			qcom_glink_handle_intent(glink, param1, param2, avail);
 			break;
-		case RPM_CMD_RX_DONE:
+		case GLINK_CMD_RX_DONE:
 			qcom_glink_handle_rx_done(glink, param1, param2, false);
 			qcom_glink_rx_advance(glink, ALIGN(sizeof(msg), 8));
 			break;
-		case RPM_CMD_RX_DONE_W_REUSE:
+		case GLINK_CMD_RX_DONE_W_REUSE:
 			qcom_glink_handle_rx_done(glink, param1, param2, true);
 			qcom_glink_rx_advance(glink, ALIGN(sizeof(msg), 8));
 			break;
-		case RPM_CMD_RX_INTENT_REQ_ACK:
+		case GLINK_CMD_RX_INTENT_REQ_ACK:
 			qcom_glink_handle_intent_req_ack(glink, param1, param2);
 			qcom_glink_rx_advance(glink, ALIGN(sizeof(msg), 8));
 			break;
@@ -1236,7 +1272,7 @@
 
 	reinit_completion(&channel->intent_req_comp);
 
-	cmd.id = RPM_CMD_RX_INTENT_REQ;
+	cmd.id = GLINK_CMD_RX_INTENT_REQ;
 	cmd.cid = channel->lcid;
 	cmd.size = size;
 
@@ -1271,6 +1307,8 @@
 	} __packed req;
 	int ret;
 	unsigned long flags;
+	int chunk_size = len;
+	int left_size = 0;
 
 	if (!glink->intentless) {
 		while (!intent) {
@@ -1304,18 +1342,48 @@
 		iid = intent->id;
 	}
 
-	req.msg.cmd = cpu_to_le16(RPM_CMD_TX_DATA);
+	if (wait && chunk_size > SZ_8K) {
+		chunk_size = SZ_8K;
+		left_size = len - chunk_size;
+	}
+	req.msg.cmd = cpu_to_le16(GLINK_CMD_TX_DATA);
 	req.msg.param1 = cpu_to_le16(channel->lcid);
 	req.msg.param2 = cpu_to_le32(iid);
-	req.chunk_size = cpu_to_le32(len);
-	req.left_size = cpu_to_le32(0);
+	req.chunk_size = cpu_to_le32(chunk_size);
+	req.left_size = cpu_to_le32(left_size);
 
-	ret = qcom_glink_tx(glink, &req, sizeof(req), data, len, wait);
+	ret = qcom_glink_tx(glink, &req, sizeof(req), data, chunk_size, wait);
 
 	/* Mark intent available if we failed */
-	if (ret && intent)
-		intent->in_use = false;
+	if (ret) {
+		if (intent)
+			intent->in_use = false;
+		return ret;
+	}
+
+	while (left_size > 0) {
+		data = (void *)((char *)data + chunk_size);
+		chunk_size = left_size;
+		if (chunk_size > SZ_8K)
+			chunk_size = SZ_8K;
+		left_size -= chunk_size;
+
+		req.msg.cmd = cpu_to_le16(GLINK_CMD_TX_DATA_CONT);
+		req.msg.param1 = cpu_to_le16(channel->lcid);
+		req.msg.param2 = cpu_to_le32(iid);
+		req.chunk_size = cpu_to_le32(chunk_size);
+		req.left_size = cpu_to_le32(left_size);
 
+		ret = qcom_glink_tx(glink, &req, sizeof(req), data,
+				    chunk_size, wait);
+
+		/* Mark intent available if we failed */
+		if (ret) {
+			if (intent)
+				intent->in_use = false;
+			break;
+		}
+	}
 	return ret;
 }
 
@@ -1390,6 +1458,7 @@
 	struct glink_channel *channel = to_glink_channel(rpdev->ept);
 
 	channel->rpdev = NULL;
+	kfree(rpdev->driver_override);
 	kfree(rpdev);
 }
 
@@ -1488,7 +1557,7 @@
 	cancel_work_sync(&channel->intent_work);
 
 	if (channel->rpdev) {
-		strncpy(chinfo.name, channel->name, sizeof(chinfo.name));
+		strscpy_pad(chinfo.name, channel->name, sizeof(chinfo.name));
 		chinfo.src = RPMSG_ADDR_ANY;
 		chinfo.dst = RPMSG_ADDR_ANY;
 
@@ -1510,6 +1579,9 @@
 	struct glink_channel *channel;
 	unsigned long flags;
 
+	/* To wakeup any blocking writers */
+	wake_up_all(&glink->tx_avail_notify);
+
 	spin_lock_irqsave(&glink->idr_lock, flags);
 	channel = idr_find(&glink->lcids, lcid);
 	if (WARN(!channel, "close ack on unknown channel\n")) {
@@ -1552,22 +1624,22 @@
 		param2 = le32_to_cpu(msg->param2);
 
 		switch (cmd) {
-		case RPM_CMD_VERSION:
+		case GLINK_CMD_VERSION:
 			qcom_glink_receive_version(glink, param1, param2);
 			break;
-		case RPM_CMD_VERSION_ACK:
+		case GLINK_CMD_VERSION_ACK:
 			qcom_glink_receive_version_ack(glink, param1, param2);
 			break;
-		case RPM_CMD_OPEN:
+		case GLINK_CMD_OPEN:
 			qcom_glink_rx_open(glink, param1, msg->data);
 			break;
-		case RPM_CMD_CLOSE:
+		case GLINK_CMD_CLOSE:
 			qcom_glink_rx_close(glink, param1);
 			break;
-		case RPM_CMD_CLOSE_ACK:
+		case GLINK_CMD_CLOSE_ACK:
 			qcom_glink_rx_close_ack(glink, param1);
 			break;
-		case RPM_CMD_RX_INTENT_REQ:
+		case GLINK_CMD_RX_INTENT_REQ:
 			qcom_glink_handle_intent_req(glink, param1, param2);
 			break;
 		default:
@@ -1618,6 +1690,7 @@
 
 	/* Release qcom_glink_alloc_channel() reference */
 	kref_put(&channel->refcount, qcom_glink_channel_release);
+	kfree(rpdev->driver_override);
 	kfree(rpdev);
 }
 
@@ -1670,6 +1743,7 @@
 	spin_lock_init(&glink->rx_lock);
 	INIT_LIST_HEAD(&glink->rx_queue);
 	INIT_WORK(&glink->rx_work, qcom_glink_work);
+	init_waitqueue_head(&glink->tx_avail_notify);
 
 	spin_lock_init(&glink->idr_lock);
 	idr_init(&glink->lcids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/qcom_smd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/qcom_smd.c
@@ -1089,7 +1089,7 @@
 
 	/* Assign public information to the rpmsg_device */
 	rpdev = &qsdev->rpdev;
-	strncpy(rpdev->id.name, channel->name, RPMSG_NAME_SIZE);
+	strscpy_pad(rpdev->id.name, channel->name, RPMSG_NAME_SIZE);
 	rpdev->src = RPMSG_ADDR_ANY;
 	rpdev->dst = RPMSG_ADDR_ANY;
 
@@ -1320,7 +1320,7 @@
 
 		spin_unlock_irqrestore(&edge->channels_lock, flags);
 
-		strncpy(chinfo.name, channel->name, sizeof(chinfo.name));
+		strscpy_pad(chinfo.name, channel->name, sizeof(chinfo.name));
 		chinfo.src = RPMSG_ADDR_ANY;
 		chinfo.dst = RPMSG_ADDR_ANY;
 		rpmsg_unregister_device(&edge->dev, &chinfo);
@@ -1380,6 +1380,7 @@
 		}
 
 		edge->ipc_regmap = syscon_node_to_regmap(syscon_np);
+		of_node_put(syscon_np);
 		if (IS_ERR(edge->ipc_regmap)) {
 			ret = PTR_ERR(edge->ipc_regmap);
 			goto put_node;
@@ -1404,9 +1405,9 @@
 		edge->name = node->name;
 
 	irq = irq_of_parse_and_map(node, 0);
-	if (irq < 0) {
+	if (!irq) {
 		dev_err(dev, "required smd interrupt missing\n");
-		ret = irq;
+		ret = -EINVAL;
 		goto put_node;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/rpmsg_char.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/rpmsg_char.c
@@ -92,7 +92,7 @@
 	/* wake up any blocked readers */
 	wake_up_interruptible(&eptdev->readq);
 
-	device_del(&eptdev->dev);
+	cdev_device_del(&eptdev->cdev, &eptdev->dev);
 	put_device(&eptdev->dev);
 
 	return 0;
@@ -127,8 +127,11 @@
 	struct rpmsg_device *rpdev = eptdev->rpdev;
 	struct device *dev = &eptdev->dev;
 
-	if (eptdev->ept)
+	mutex_lock(&eptdev->ept_lock);
+	if (eptdev->ept) {
+		mutex_unlock(&eptdev->ept_lock);
 		return -EBUSY;
+	}
 
 	get_device(dev);
 
@@ -136,11 +139,13 @@
 	if (!ept) {
 		dev_err(dev, "failed to open %s\n", eptdev->chinfo.name);
 		put_device(dev);
+		mutex_unlock(&eptdev->ept_lock);
 		return -EINVAL;
 	}
 
 	eptdev->ept = ept;
 	filp->private_data = eptdev;
+	mutex_unlock(&eptdev->ept_lock);
 
 	return 0;
 }
@@ -335,7 +340,6 @@
 
 	ida_simple_remove(&rpmsg_ept_ida, dev->id);
 	ida_simple_remove(&rpmsg_minor_ida, MINOR(eptdev->dev.devt));
-	cdev_del(&eptdev->cdev);
 	kfree(eptdev);
 }
 
@@ -380,19 +384,13 @@
 	dev->id = ret;
 	dev_set_name(dev, "rpmsg%d", ret);
 
-	ret = cdev_add(&eptdev->cdev, dev->devt, 1);
+	ret = cdev_device_add(&eptdev->cdev, &eptdev->dev);
 	if (ret)
 		goto free_ept_ida;
 
 	/* We can now rely on the release function for cleanup */
 	dev->release = rpmsg_eptdev_release_device;
 
-	ret = device_add(dev);
-	if (ret) {
-		dev_err(dev, "device_add failed: %d\n", ret);
-		put_device(dev);
-	}
-
 	return ret;
 
 free_ept_ida:
@@ -461,7 +459,6 @@
 
 	ida_simple_remove(&rpmsg_ctrl_ida, dev->id);
 	ida_simple_remove(&rpmsg_minor_ida, MINOR(dev->devt));
-	cdev_del(&ctrldev->cdev);
 	kfree(ctrldev);
 }
 
@@ -496,19 +493,13 @@
 	dev->id = ret;
 	dev_set_name(&ctrldev->dev, "rpmsg_ctrl%d", ret);
 
-	ret = cdev_add(&ctrldev->cdev, dev->devt, 1);
+	ret = cdev_device_add(&ctrldev->cdev, &ctrldev->dev);
 	if (ret)
 		goto free_ctrl_ida;
 
 	/* We can now rely on the release function for cleanup */
 	dev->release = rpmsg_ctrldev_release_device;
 
-	ret = device_add(dev);
-	if (ret) {
-		dev_err(&rpdev->dev, "device_add failed: %d\n", ret);
-		put_device(dev);
-	}
-
 	dev_set_drvdata(&rpdev->dev, ctrldev);
 
 	return ret;
@@ -534,7 +525,7 @@
 	if (ret)
 		dev_warn(&rpdev->dev, "failed to nuke endpoints: %d\n", ret);
 
-	device_del(&ctrldev->dev);
+	cdev_device_del(&ctrldev->cdev, &ctrldev->dev);
 	put_device(&ctrldev->dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/rpmsg_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/rpmsg_core.c
@@ -376,7 +376,8 @@
 	      const char *buf, size_t sz)				\
 {									\
 	struct rpmsg_device *rpdev = to_rpmsg_device(dev);		\
-	char *new, *old;						\
+	const char *old;						\
+	char *new;							\
 									\
 	new = kstrndup(buf, sz, GFP_KERNEL);				\
 	if (!new)							\
@@ -519,13 +520,25 @@
 	err = rpdrv->probe(rpdev);
 	if (err) {
 		dev_err(dev, "%s: failed: %d\n", __func__, err);
-		if (ept)
-			rpmsg_destroy_ept(ept);
-		goto out;
+		goto destroy_ept;
 	}
 
-	if (ept && rpdev->ops->announce_create)
+	if (ept && rpdev->ops->announce_create) {
 		err = rpdev->ops->announce_create(rpdev);
+		if (err) {
+			dev_err(dev, "failed to announce creation\n");
+			goto remove_rpdev;
+		}
+	}
+
+	return 0;
+
+remove_rpdev:
+	if (rpdrv->remove)
+		rpdrv->remove(rpdev);
+destroy_ept:
+	if (ept)
+		rpmsg_destroy_ept(ept);
 out:
 	return err;
 }
@@ -556,24 +569,52 @@
 	.remove		= rpmsg_dev_remove,
 };
 
-int rpmsg_register_device(struct rpmsg_device *rpdev)
+/*
+ * A helper for registering rpmsg device with driver override and name.
+ * Drivers should not be using it, but instead rpmsg_register_device().
+ */
+int rpmsg_register_device_override(struct rpmsg_device *rpdev,
+				   const char *driver_override)
 {
 	struct device *dev = &rpdev->dev;
 	int ret;
 
+	if (driver_override)
+		strcpy(rpdev->id.name, driver_override);
+
 	dev_set_name(&rpdev->dev, "%s.%s.%d.%d", dev_name(dev->parent),
 		     rpdev->id.name, rpdev->src, rpdev->dst);
 
 	rpdev->dev.bus = &rpmsg_bus;
 
-	ret = device_register(&rpdev->dev);
+	device_initialize(dev);
+	if (driver_override) {
+		ret = driver_set_override(dev, &rpdev->driver_override,
+					  driver_override,
+					  strlen(driver_override));
+		if (ret) {
+			dev_err(dev, "device_set_override failed: %d\n", ret);
+			put_device(dev);
+			return ret;
+		}
+	}
+
+	ret = device_add(dev);
 	if (ret) {
-		dev_err(dev, "device_register failed: %d\n", ret);
+		dev_err(dev, "device_add failed: %d\n", ret);
+		kfree(rpdev->driver_override);
+		rpdev->driver_override = NULL;
 		put_device(&rpdev->dev);
 	}
 
 	return ret;
 }
+EXPORT_SYMBOL(rpmsg_register_device_override);
+
+int rpmsg_register_device(struct rpmsg_device *rpdev)
+{
+	return rpmsg_register_device_override(rpdev, NULL);
+}
 EXPORT_SYMBOL(rpmsg_register_device);
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/rpmsg_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/rpmsg_internal.h
@@ -90,10 +90,7 @@
  */
 static inline int rpmsg_chrdev_register_device(struct rpmsg_device *rpdev)
 {
-	strcpy(rpdev->id.name, "rpmsg_chrdev");
-	rpdev->driver_override = "rpmsg_chrdev";
-
-	return rpmsg_register_device(rpdev);
+	return rpmsg_register_device_override(rpdev, "rpmsg_ctrl");
 }
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/rpmsg_ns.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/rpmsg_ns.c
@@ -20,12 +20,10 @@
  */
 int rpmsg_ns_register_device(struct rpmsg_device *rpdev)
 {
-	strcpy(rpdev->id.name, "rpmsg_ns");
-	rpdev->driver_override = "rpmsg_ns";
 	rpdev->src = RPMSG_NS_ADDR;
 	rpdev->dst = RPMSG_NS_ADDR;
 
-	return rpmsg_register_device(rpdev);
+	return rpmsg_register_device_override(rpdev, "rpmsg_ns");
 }
 EXPORT_SYMBOL(rpmsg_ns_register_device);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rpmsg/virtio_rpmsg_bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rpmsg/virtio_rpmsg_bus.c
@@ -377,6 +377,7 @@
 	struct rpmsg_device *rpdev = to_rpmsg_device(dev);
 	struct virtio_rpmsg_channel *vch = to_virtio_rpmsg_channel(rpdev);
 
+	kfree(rpdev->driver_override);
 	kfree(vch);
 }
 
@@ -842,7 +843,7 @@
 
 	err = rpmsg_chrdev_register_device(rpdev_ctrl);
 	if (err) {
-		kfree(vch);
+		/* vch will be free in virtio_rpmsg_release_device() */
 		return ERR_PTR(err);
 	}
 
@@ -853,7 +854,7 @@
 {
 	if (!rpdev_ctrl)
 		return;
-	kfree(to_virtio_rpmsg_channel(rpdev_ctrl));
+	device_unregister(&rpdev_ctrl->dev);
 }
 
 static int rpmsg_probe(struct virtio_device *vdev)
@@ -964,7 +965,8 @@
 
 		err = rpmsg_ns_register_device(rpdev_ns);
 		if (err)
-			goto free_vch;
+			/* vch will be free in virtio_rpmsg_release_device() */
+			goto free_ctrldev;
 	}
 
 	/*
@@ -988,8 +990,6 @@
 
 	return 0;
 
-free_vch:
-	kfree(vch);
 free_ctrldev:
 	rpmsg_virtio_del_ctrl_dev(rpdev_ctrl);
 free_coherent:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/Kconfig
@@ -457,6 +457,16 @@
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-pcf85063.
 
+config RTC_DRV_PCF85263
+	tristate "NXP PCF85263"
+	depends on UBUNTU_ODM_DRIVERS
+	select REGMAP_I2C
+	help
+	  If you say yes here you get support for the PCF85263 RTC chip.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called rtc-pcf85263.
+
 config RTC_DRV_PCF85363
 	tristate "NXP PCF85363"
 	select REGMAP_I2C
@@ -1814,7 +1824,8 @@
 
 config RTC_DRV_MT6397
 	tristate "MediaTek PMIC based RTC"
-	depends on MFD_MT6397 || (COMPILE_TEST && IRQ_DOMAIN)
+	depends on MFD_MT6397 || COMPILE_TEST
+	select IRQ_DOMAIN
 	help
 	  This selects the MediaTek(R) RTC driver. RTC is part of MediaTek
 	  MT6397 PMIC. You should enable MT6397 PMIC MFD before select
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/Makefile
@@ -120,6 +120,7 @@
 obj-$(CONFIG_RTC_DRV_PCF50633)	+= rtc-pcf50633.o
 obj-$(CONFIG_RTC_DRV_PCF85063)	+= rtc-pcf85063.o
 obj-$(CONFIG_RTC_DRV_PCF8523)	+= rtc-pcf8523.o
+obj-$(CONFIG_RTC_DRV_PCF85263)	+= rtc-pcf85263.o
 obj-$(CONFIG_RTC_DRV_PCF85363)	+= rtc-pcf85363.o
 obj-$(CONFIG_RTC_DRV_PCF8563)	+= rtc-pcf8563.o
 obj-$(CONFIG_RTC_DRV_PCF8583)	+= rtc-pcf8583.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/class.c
@@ -26,6 +26,15 @@
 static void rtc_device_release(struct device *dev)
 {
 	struct rtc_device *rtc = to_rtc_device(dev);
+	struct timerqueue_head *head = &rtc->timerqueue;
+	struct timerqueue_node *node;
+
+	mutex_lock(&rtc->ops_lock);
+	while ((node = timerqueue_getnext(head)))
+		timerqueue_del(head, node);
+	mutex_unlock(&rtc->ops_lock);
+
+	cancel_work_sync(&rtc->irqwork);
 
 	ida_simple_remove(&rtc_ida, rtc->id);
 	mutex_destroy(&rtc->ops_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/interface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/interface.c
@@ -274,10 +274,9 @@
 			return err;
 
 		/* full-function RTCs won't have such missing fields */
-		if (rtc_valid_tm(&alarm->time) == 0) {
-			rtc_add_offset(rtc, &alarm->time);
-			return 0;
-		}
+		err = rtc_valid_tm(&alarm->time);
+		if (!err)
+			goto done;
 
 		/* get the "after" timestamp, to detect wrapped fields */
 		err = rtc_read_time(rtc, &now);
@@ -379,6 +378,8 @@
 	if (err)
 		dev_warn(&rtc->dev, "invalid alarm value: %ptR\n",
 			 &alarm->time);
+	else
+		rtc_add_offset(rtc, &alarm->time);
 
 	return err;
 }
@@ -392,7 +393,7 @@
 		return err;
 	if (!rtc->ops) {
 		err = -ENODEV;
-	} else if (!test_bit(RTC_FEATURE_ALARM, rtc->features) || !rtc->ops->read_alarm) {
+	} else if (!test_bit(RTC_FEATURE_ALARM, rtc->features)) {
 		err = -EINVAL;
 	} else {
 		memset(alarm, 0, sizeof(struct rtc_wkalrm));
@@ -793,9 +794,13 @@
 	struct timerqueue_node *next = timerqueue_getnext(&rtc->timerqueue);
 	struct rtc_time tm;
 	ktime_t now;
+	int err;
+
+	err = __rtc_read_time(rtc, &tm);
+	if (err)
+		return err;
 
 	timer->enabled = 1;
-	__rtc_read_time(rtc, &tm);
 	now = rtc_tm_to_ktime(tm);
 
 	/* Skip over expired timers */
@@ -809,7 +814,6 @@
 	trace_rtc_timer_enqueue(timer);
 	if (!next || ktime_before(timer->node.expires, next->expires)) {
 		struct rtc_wkalrm alarm;
-		int err;
 
 		alarm.time = rtc_ktime_to_tm(timer->node.expires);
 		alarm.enabled = 1;
@@ -889,13 +893,18 @@
 	struct timerqueue_node *next;
 	ktime_t now;
 	struct rtc_time tm;
+	int err;
 
 	struct rtc_device *rtc =
 		container_of(work, struct rtc_device, irqwork);
 
 	mutex_lock(&rtc->ops_lock);
 again:
-	__rtc_read_time(rtc, &tm);
+	err = __rtc_read_time(rtc, &tm);
+	if (err) {
+		mutex_unlock(&rtc->ops_lock);
+		return;
+	}
 	now = rtc_tm_to_ktime(tm);
 	while ((next = timerqueue_getnext(&rtc->timerqueue))) {
 		if (next->expires > now)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/lib_test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/lib_test.c
@@ -54,7 +54,7 @@
 
 		days = div_s64(secs, 86400);
 
-		#define FAIL_MSG "%d/%02d/%02d (%2d) : %ld", \
+		#define FAIL_MSG "%d/%02d/%02d (%2d) : %lld", \
 			year, month, mday, yday, days
 
 		KUNIT_ASSERT_EQ_MSG(test, year - 1900, result.tm_year, FAIL_MSG);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-ab-eoz9.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-ab-eoz9.c
@@ -396,13 +396,6 @@
 	if (ret < 0)
 		return ret;
 
-	if ((val & ABEOZ9_REG_CTRL_STATUS_V1F) ||
-	    (val & ABEOZ9_REG_CTRL_STATUS_V2F)) {
-		dev_err(dev,
-			"thermometer might be disabled due to low voltage\n");
-		return -EINVAL;
-	}
-
 	switch (attr) {
 	case hwmon_temp_input:
 		ret = regmap_read(regmap, ABEOZ9_REG_REG_TEMP, &val);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-abx80x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-abx80x.c
@@ -37,7 +37,7 @@
 #define ABX8XX_REG_STATUS	0x0f
 #define ABX8XX_STATUS_AF	BIT(2)
 #define ABX8XX_STATUS_BLF	BIT(4)
-#define ABX8XX_STATUS_WDT	BIT(6)
+#define ABX8XX_STATUS_WDT	BIT(5)
 
 #define ABX8XX_REG_CTRL1	0x10
 #define ABX8XX_CTRL_WRITE	BIT(0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-at91sam9.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-at91sam9.c
@@ -368,6 +368,7 @@
 		return ret;
 
 	rtc->gpbr = syscon_node_to_regmap(args.np);
+	of_node_put(args.np);
 	rtc->gpbr_offset = args.args[0];
 	if (IS_ERR(rtc->gpbr)) {
 		dev_err(&pdev->dev, "failed to retrieve gpbr regmap, aborting.\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-cmos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-cmos.c
@@ -222,6 +222,8 @@
 
 static int cmos_read_time(struct device *dev, struct rtc_time *t)
 {
+	int ret;
+
 	/*
 	 * If pm_trace abused the RTC for storage, set the timespec to 0,
 	 * which tells the caller that this RTC value is unusable.
@@ -229,7 +231,12 @@
 	if (!pm_trace_rtc_valid())
 		return -EIO;
 
-	mc146818_get_time(t);
+	ret = mc146818_get_time(t);
+	if (ret < 0) {
+		dev_err_ratelimited(dev, "unable to read current time\n");
+		return ret;
+	}
+
 	return 0;
 }
 
@@ -242,42 +249,68 @@
 	return mc146818_set_time(t);
 }
 
+struct cmos_read_alarm_callback_param {
+	struct cmos_rtc *cmos;
+	struct rtc_time *time;
+	unsigned char	rtc_control;
+};
+
+static void cmos_read_alarm_callback(unsigned char __always_unused seconds,
+				     void *param_in)
+{
+	struct cmos_read_alarm_callback_param *p =
+		(struct cmos_read_alarm_callback_param *)param_in;
+	struct rtc_time *time = p->time;
+
+	time->tm_sec = CMOS_READ(RTC_SECONDS_ALARM);
+	time->tm_min = CMOS_READ(RTC_MINUTES_ALARM);
+	time->tm_hour = CMOS_READ(RTC_HOURS_ALARM);
+
+	if (p->cmos->day_alrm) {
+		/* ignore upper bits on readback per ACPI spec */
+		time->tm_mday = CMOS_READ(p->cmos->day_alrm) & 0x3f;
+		if (!time->tm_mday)
+			time->tm_mday = -1;
+
+		if (p->cmos->mon_alrm) {
+			time->tm_mon = CMOS_READ(p->cmos->mon_alrm);
+			if (!time->tm_mon)
+				time->tm_mon = -1;
+		}
+	}
+
+	p->rtc_control = CMOS_READ(RTC_CONTROL);
+}
+
 static int cmos_read_alarm(struct device *dev, struct rtc_wkalrm *t)
 {
 	struct cmos_rtc	*cmos = dev_get_drvdata(dev);
-	unsigned char	rtc_control;
+	struct cmos_read_alarm_callback_param p = {
+		.cmos = cmos,
+		.time = &t->time,
+	};
 
 	/* This not only a rtc_op, but also called directly */
 	if (!is_valid_irq(cmos->irq))
-		return -EIO;
+		return -ETIMEDOUT;
 
 	/* Basic alarms only support hour, minute, and seconds fields.
 	 * Some also support day and month, for alarms up to a year in
 	 * the future.
 	 */
 
-	spin_lock_irq(&rtc_lock);
-	t->time.tm_sec = CMOS_READ(RTC_SECONDS_ALARM);
-	t->time.tm_min = CMOS_READ(RTC_MINUTES_ALARM);
-	t->time.tm_hour = CMOS_READ(RTC_HOURS_ALARM);
-
-	if (cmos->day_alrm) {
-		/* ignore upper bits on readback per ACPI spec */
-		t->time.tm_mday = CMOS_READ(cmos->day_alrm) & 0x3f;
-		if (!t->time.tm_mday)
-			t->time.tm_mday = -1;
-
-		if (cmos->mon_alrm) {
-			t->time.tm_mon = CMOS_READ(cmos->mon_alrm);
-			if (!t->time.tm_mon)
-				t->time.tm_mon = -1;
-		}
-	}
-
-	rtc_control = CMOS_READ(RTC_CONTROL);
-	spin_unlock_irq(&rtc_lock);
+	/* Some Intel chipsets disconnect the alarm registers when the clock
+	 * update is in progress - during this time reads return bogus values
+	 * and writes may fail silently. See for example "7th Generation Intel®
+	 * Processor Family I/O for U/Y Platforms [...] Datasheet", section
+	 * 27.7.1
+	 *
+	 * Use the mc146818_avoid_UIP() function to avoid this.
+	 */
+	if (!mc146818_avoid_UIP(cmos_read_alarm_callback, &p))
+		return -EIO;
 
-	if (!(rtc_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+	if (!(p.rtc_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
 		if (((unsigned)t->time.tm_sec) < 0x60)
 			t->time.tm_sec = bcd2bin(t->time.tm_sec);
 		else
@@ -306,7 +339,7 @@
 		}
 	}
 
-	t->enabled = !!(rtc_control & RTC_AIE);
+	t->enabled = !!(p.rtc_control & RTC_AIE);
 	t->pending = 0;
 
 	return 0;
@@ -437,10 +470,57 @@
 	return 0;
 }
 
+struct cmos_set_alarm_callback_param {
+	struct cmos_rtc *cmos;
+	unsigned char mon, mday, hrs, min, sec;
+	struct rtc_wkalrm *t;
+};
+
+/* Note: this function may be executed by mc146818_avoid_UIP() more then
+ *	 once
+ */
+static void cmos_set_alarm_callback(unsigned char __always_unused seconds,
+				    void *param_in)
+{
+	struct cmos_set_alarm_callback_param *p =
+		(struct cmos_set_alarm_callback_param *)param_in;
+
+	/* next rtc irq must not be from previous alarm setting */
+	cmos_irq_disable(p->cmos, RTC_AIE);
+
+	/* update alarm */
+	CMOS_WRITE(p->hrs, RTC_HOURS_ALARM);
+	CMOS_WRITE(p->min, RTC_MINUTES_ALARM);
+	CMOS_WRITE(p->sec, RTC_SECONDS_ALARM);
+
+	/* the system may support an "enhanced" alarm */
+	if (p->cmos->day_alrm) {
+		CMOS_WRITE(p->mday, p->cmos->day_alrm);
+		if (p->cmos->mon_alrm)
+			CMOS_WRITE(p->mon, p->cmos->mon_alrm);
+	}
+
+	if (use_hpet_alarm()) {
+		/*
+		 * FIXME the HPET alarm glue currently ignores day_alrm
+		 * and mon_alrm ...
+		 */
+		hpet_set_alarm_time(p->t->time.tm_hour, p->t->time.tm_min,
+				    p->t->time.tm_sec);
+	}
+
+	if (p->t->enabled)
+		cmos_irq_enable(p->cmos, RTC_AIE);
+}
+
 static int cmos_set_alarm(struct device *dev, struct rtc_wkalrm *t)
 {
 	struct cmos_rtc	*cmos = dev_get_drvdata(dev);
-	unsigned char mon, mday, hrs, min, sec, rtc_control;
+	struct cmos_set_alarm_callback_param p = {
+		.cmos = cmos,
+		.t = t
+	};
+	unsigned char rtc_control;
 	int ret;
 
 	/* This not only a rtc_op, but also called directly */
@@ -451,52 +531,33 @@
 	if (ret < 0)
 		return ret;
 
-	mon = t->time.tm_mon + 1;
-	mday = t->time.tm_mday;
-	hrs = t->time.tm_hour;
-	min = t->time.tm_min;
-	sec = t->time.tm_sec;
+	p.mon = t->time.tm_mon + 1;
+	p.mday = t->time.tm_mday;
+	p.hrs = t->time.tm_hour;
+	p.min = t->time.tm_min;
+	p.sec = t->time.tm_sec;
 
+	spin_lock_irq(&rtc_lock);
 	rtc_control = CMOS_READ(RTC_CONTROL);
+	spin_unlock_irq(&rtc_lock);
+
 	if (!(rtc_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
 		/* Writing 0xff means "don't care" or "match all".  */
-		mon = (mon <= 12) ? bin2bcd(mon) : 0xff;
-		mday = (mday >= 1 && mday <= 31) ? bin2bcd(mday) : 0xff;
-		hrs = (hrs < 24) ? bin2bcd(hrs) : 0xff;
-		min = (min < 60) ? bin2bcd(min) : 0xff;
-		sec = (sec < 60) ? bin2bcd(sec) : 0xff;
-	}
-
-	spin_lock_irq(&rtc_lock);
-
-	/* next rtc irq must not be from previous alarm setting */
-	cmos_irq_disable(cmos, RTC_AIE);
-
-	/* update alarm */
-	CMOS_WRITE(hrs, RTC_HOURS_ALARM);
-	CMOS_WRITE(min, RTC_MINUTES_ALARM);
-	CMOS_WRITE(sec, RTC_SECONDS_ALARM);
-
-	/* the system may support an "enhanced" alarm */
-	if (cmos->day_alrm) {
-		CMOS_WRITE(mday, cmos->day_alrm);
-		if (cmos->mon_alrm)
-			CMOS_WRITE(mon, cmos->mon_alrm);
+		p.mon = (p.mon <= 12) ? bin2bcd(p.mon) : 0xff;
+		p.mday = (p.mday >= 1 && p.mday <= 31) ? bin2bcd(p.mday) : 0xff;
+		p.hrs = (p.hrs < 24) ? bin2bcd(p.hrs) : 0xff;
+		p.min = (p.min < 60) ? bin2bcd(p.min) : 0xff;
+		p.sec = (p.sec < 60) ? bin2bcd(p.sec) : 0xff;
 	}
 
-	if (use_hpet_alarm()) {
-		/*
-		 * FIXME the HPET alarm glue currently ignores day_alrm
-		 * and mon_alrm ...
-		 */
-		hpet_set_alarm_time(t->time.tm_hour, t->time.tm_min,
-				    t->time.tm_sec);
-	}
-
-	if (t->enabled)
-		cmos_irq_enable(cmos, RTC_AIE);
-
-	spin_unlock_irq(&rtc_lock);
+	/*
+	 * Some Intel chipsets disconnect the alarm registers when the clock
+	 * update is in progress - during this time writes fail silently.
+	 *
+	 * Use mc146818_avoid_UIP() to avoid this.
+	 */
+	if (!mc146818_avoid_UIP(cmos_set_alarm_callback, &p))
+		return -ETIMEDOUT;
 
 	cmos->alarm_expires = rtc_tm_to_time64(&t->time);
 
@@ -582,11 +643,10 @@
 			   size_t count)
 {
 	unsigned char *buf = val;
-	int	retval;
 
 	off += NVRAM_OFFSET;
 	spin_lock_irq(&rtc_lock);
-	for (retval = 0; count; count--, off++, retval++) {
+	for (; count; count--, off++) {
 		if (off < 128)
 			*buf++ = CMOS_READ(off);
 		else if (can_bank2)
@@ -596,7 +656,7 @@
 	}
 	spin_unlock_irq(&rtc_lock);
 
-	return retval;
+	return count ? -EIO : 0;
 }
 
 static int cmos_nvram_write(void *priv, unsigned int off, void *val,
@@ -604,7 +664,6 @@
 {
 	struct cmos_rtc	*cmos = priv;
 	unsigned char	*buf = val;
-	int		retval;
 
 	/* NOTE:  on at least PCs and Ataris, the boot firmware uses a
 	 * checksum on part of the NVRAM data.  That's currently ignored
@@ -613,7 +672,7 @@
 	 */
 	off += NVRAM_OFFSET;
 	spin_lock_irq(&rtc_lock);
-	for (retval = 0; count; count--, off++, retval++) {
+	for (; count; count--, off++) {
 		/* don't trash RTC registers */
 		if (off == cmos->day_alrm
 				|| off == cmos->mon_alrm
@@ -628,7 +687,7 @@
 	}
 	spin_unlock_irq(&rtc_lock);
 
-	return retval;
+	return count ? -EIO : 0;
 }
 
 /*----------------------------------------------------------------*/
@@ -683,6 +742,168 @@
 		return IRQ_NONE;
 }
 
+#ifdef	CONFIG_ACPI
+
+#include <linux/acpi.h>
+
+static u32 rtc_handler(void *context)
+{
+	struct device *dev = context;
+	struct cmos_rtc *cmos = dev_get_drvdata(dev);
+	unsigned char rtc_control = 0;
+	unsigned char rtc_intr;
+	unsigned long flags;
+
+
+	/*
+	 * Always update rtc irq when ACPI is used as RTC Alarm.
+	 * Or else, ACPI SCI is enabled during suspend/resume only,
+	 * update rtc irq in that case.
+	 */
+	if (cmos_use_acpi_alarm())
+		cmos_interrupt(0, (void *)cmos->rtc);
+	else {
+		/* Fix me: can we use cmos_interrupt() here as well? */
+		spin_lock_irqsave(&rtc_lock, flags);
+		if (cmos_rtc.suspend_ctrl)
+			rtc_control = CMOS_READ(RTC_CONTROL);
+		if (rtc_control & RTC_AIE) {
+			cmos_rtc.suspend_ctrl &= ~RTC_AIE;
+			CMOS_WRITE(rtc_control, RTC_CONTROL);
+			rtc_intr = CMOS_READ(RTC_INTR_FLAGS);
+			rtc_update_irq(cmos->rtc, 1, rtc_intr);
+		}
+		spin_unlock_irqrestore(&rtc_lock, flags);
+	}
+
+	pm_wakeup_hard_event(dev);
+	acpi_clear_event(ACPI_EVENT_RTC);
+	acpi_disable_event(ACPI_EVENT_RTC, 0);
+	return ACPI_INTERRUPT_HANDLED;
+}
+
+static void acpi_rtc_event_setup(struct device *dev)
+{
+	if (acpi_disabled)
+		return;
+
+	acpi_install_fixed_event_handler(ACPI_EVENT_RTC, rtc_handler, dev);
+	/*
+	 * After the RTC handler is installed, the Fixed_RTC event should
+	 * be disabled. Only when the RTC alarm is set will it be enabled.
+	 */
+	acpi_clear_event(ACPI_EVENT_RTC);
+	acpi_disable_event(ACPI_EVENT_RTC, 0);
+}
+
+static void acpi_rtc_event_cleanup(void)
+{
+	if (acpi_disabled)
+		return;
+
+	acpi_remove_fixed_event_handler(ACPI_EVENT_RTC, rtc_handler);
+}
+
+static void rtc_wake_on(struct device *dev)
+{
+	acpi_clear_event(ACPI_EVENT_RTC);
+	acpi_enable_event(ACPI_EVENT_RTC, 0);
+}
+
+static void rtc_wake_off(struct device *dev)
+{
+	acpi_disable_event(ACPI_EVENT_RTC, 0);
+}
+
+#ifdef CONFIG_X86
+/* Enable use_acpi_alarm mode for Intel platforms no earlier than 2015 */
+static void use_acpi_alarm_quirks(void)
+{
+	if (boot_cpu_data.x86_vendor != X86_VENDOR_INTEL)
+		return;
+
+	if (!is_hpet_enabled())
+		return;
+
+	if (dmi_get_bios_year() < 2015)
+		return;
+
+	use_acpi_alarm = true;
+}
+#else
+static inline void use_acpi_alarm_quirks(void) { }
+#endif
+
+static void acpi_cmos_wake_setup(struct device *dev)
+{
+	if (acpi_disabled)
+		return;
+
+	use_acpi_alarm_quirks();
+
+	cmos_rtc.wake_on = rtc_wake_on;
+	cmos_rtc.wake_off = rtc_wake_off;
+
+	/* ACPI tables bug workaround. */
+	if (acpi_gbl_FADT.month_alarm && !acpi_gbl_FADT.day_alarm) {
+		dev_dbg(dev, "bogus FADT month_alarm (%d)\n",
+			acpi_gbl_FADT.month_alarm);
+		acpi_gbl_FADT.month_alarm = 0;
+	}
+
+	cmos_rtc.day_alrm = acpi_gbl_FADT.day_alarm;
+	cmos_rtc.mon_alrm = acpi_gbl_FADT.month_alarm;
+	cmos_rtc.century = acpi_gbl_FADT.century;
+
+	if (acpi_gbl_FADT.flags & ACPI_FADT_S4_RTC_WAKE)
+		dev_info(dev, "RTC can wake from S4\n");
+
+	/* RTC always wakes from S1/S2/S3, and often S4/STD */
+	device_init_wakeup(dev, 1);
+}
+
+static void cmos_check_acpi_rtc_status(struct device *dev,
+					      unsigned char *rtc_control)
+{
+	struct cmos_rtc *cmos = dev_get_drvdata(dev);
+	acpi_event_status rtc_status;
+	acpi_status status;
+
+	if (acpi_gbl_FADT.flags & ACPI_FADT_FIXED_RTC)
+		return;
+
+	status = acpi_get_event_status(ACPI_EVENT_RTC, &rtc_status);
+	if (ACPI_FAILURE(status)) {
+		dev_err(dev, "Could not get RTC status\n");
+	} else if (rtc_status & ACPI_EVENT_FLAG_SET) {
+		unsigned char mask;
+		*rtc_control &= ~RTC_AIE;
+		CMOS_WRITE(*rtc_control, RTC_CONTROL);
+		mask = CMOS_READ(RTC_INTR_FLAGS);
+		rtc_update_irq(cmos->rtc, 1, mask);
+	}
+}
+
+#else /* !CONFIG_ACPI */
+
+static inline void acpi_rtc_event_setup(struct device *dev)
+{
+}
+
+static inline void acpi_rtc_event_cleanup(void)
+{
+}
+
+static inline void acpi_cmos_wake_setup(struct device *dev)
+{
+}
+
+static inline void cmos_check_acpi_rtc_status(struct device *dev,
+					      unsigned char *rtc_control)
+{
+}
+#endif /* CONFIG_ACPI */
+
 #ifdef	CONFIG_PNP
 #define	INITSECTION
 
@@ -766,19 +987,27 @@
 		if (info->address_space)
 			address_space = info->address_space;
 
-		if (info->rtc_day_alarm && info->rtc_day_alarm < 128)
-			cmos_rtc.day_alrm = info->rtc_day_alarm;
-		if (info->rtc_mon_alarm && info->rtc_mon_alarm < 128)
-			cmos_rtc.mon_alrm = info->rtc_mon_alarm;
-		if (info->rtc_century && info->rtc_century < 128)
-			cmos_rtc.century = info->rtc_century;
+		cmos_rtc.day_alrm = info->rtc_day_alarm;
+		cmos_rtc.mon_alrm = info->rtc_mon_alarm;
+		cmos_rtc.century = info->rtc_century;
 
 		if (info->wake_on && info->wake_off) {
 			cmos_rtc.wake_on = info->wake_on;
 			cmos_rtc.wake_off = info->wake_off;
 		}
+	} else {
+		acpi_cmos_wake_setup(dev);
 	}
 
+	if (cmos_rtc.day_alrm >= 128)
+		cmos_rtc.day_alrm = 0;
+
+	if (cmos_rtc.mon_alrm >= 128)
+		cmos_rtc.mon_alrm = 0;
+
+	if (cmos_rtc.century >= 128)
+		cmos_rtc.century = 0;
+
 	cmos_rtc.dev = dev;
 	dev_set_drvdata(dev, &cmos_rtc);
 
@@ -790,16 +1019,14 @@
 
 	rename_region(ports, dev_name(&cmos_rtc.rtc->dev));
 
-	spin_lock_irq(&rtc_lock);
-
-	/* Ensure that the RTC is accessible. Bit 6 must be 0! */
-	if ((CMOS_READ(RTC_VALID) & 0x40) != 0) {
-		spin_unlock_irq(&rtc_lock);
-		dev_warn(dev, "not accessible\n");
+	if (!mc146818_does_rtc_work()) {
+		dev_warn(dev, "broken or not accessible\n");
 		retval = -ENXIO;
 		goto cleanup1;
 	}
 
+	spin_lock_irq(&rtc_lock);
+
 	if (!(flags & CMOS_RTC_FLAGS_NOFREQ)) {
 		/* force periodic irq to CMOS reset default of 1024Hz;
 		 *
@@ -869,6 +1096,13 @@
 	nvmem_cfg.size = address_space - NVRAM_OFFSET;
 	devm_rtc_nvmem_register(cmos_rtc.rtc, &nvmem_cfg);
 
+	/*
+	 * Everything has gone well so far, so by default register a handler for
+	 * the ACPI RTC fixed event.
+	 */
+	if (!info)
+		acpi_rtc_event_setup(dev);
+
 	dev_info(dev, "%s%s, %d bytes nvram%s\n",
 		 !is_valid_irq(rtc_irq) ? "no alarms" :
 		 cmos_rtc.mon_alrm ? "alarms up to one year" :
@@ -914,6 +1148,9 @@
 			hpet_unregister_irq_handler(cmos_interrupt);
 	}
 
+	if (!dev_get_platdata(dev))
+		acpi_rtc_event_cleanup();
+
 	cmos->rtc = NULL;
 
 	ports = cmos->iomem;
@@ -1063,9 +1300,6 @@
 	}
 }
 
-static void cmos_check_acpi_rtc_status(struct device *dev,
-				       unsigned char *rtc_control);
-
 static int __maybe_unused cmos_resume(struct device *dev)
 {
 	struct cmos_rtc	*cmos = dev_get_drvdata(dev);
@@ -1132,174 +1366,16 @@
  * predate even PNPBIOS should set up platform_bus devices.
  */
 
-#ifdef	CONFIG_ACPI
-
-#include <linux/acpi.h>
-
-static u32 rtc_handler(void *context)
-{
-	struct device *dev = context;
-	struct cmos_rtc *cmos = dev_get_drvdata(dev);
-	unsigned char rtc_control = 0;
-	unsigned char rtc_intr;
-	unsigned long flags;
-
-
-	/*
-	 * Always update rtc irq when ACPI is used as RTC Alarm.
-	 * Or else, ACPI SCI is enabled during suspend/resume only,
-	 * update rtc irq in that case.
-	 */
-	if (cmos_use_acpi_alarm())
-		cmos_interrupt(0, (void *)cmos->rtc);
-	else {
-		/* Fix me: can we use cmos_interrupt() here as well? */
-		spin_lock_irqsave(&rtc_lock, flags);
-		if (cmos_rtc.suspend_ctrl)
-			rtc_control = CMOS_READ(RTC_CONTROL);
-		if (rtc_control & RTC_AIE) {
-			cmos_rtc.suspend_ctrl &= ~RTC_AIE;
-			CMOS_WRITE(rtc_control, RTC_CONTROL);
-			rtc_intr = CMOS_READ(RTC_INTR_FLAGS);
-			rtc_update_irq(cmos->rtc, 1, rtc_intr);
-		}
-		spin_unlock_irqrestore(&rtc_lock, flags);
-	}
-
-	pm_wakeup_hard_event(dev);
-	acpi_clear_event(ACPI_EVENT_RTC);
-	acpi_disable_event(ACPI_EVENT_RTC, 0);
-	return ACPI_INTERRUPT_HANDLED;
-}
-
-static inline void rtc_wake_setup(struct device *dev)
-{
-	acpi_install_fixed_event_handler(ACPI_EVENT_RTC, rtc_handler, dev);
-	/*
-	 * After the RTC handler is installed, the Fixed_RTC event should
-	 * be disabled. Only when the RTC alarm is set will it be enabled.
-	 */
-	acpi_clear_event(ACPI_EVENT_RTC);
-	acpi_disable_event(ACPI_EVENT_RTC, 0);
-}
-
-static void rtc_wake_on(struct device *dev)
-{
-	acpi_clear_event(ACPI_EVENT_RTC);
-	acpi_enable_event(ACPI_EVENT_RTC, 0);
-}
-
-static void rtc_wake_off(struct device *dev)
-{
-	acpi_disable_event(ACPI_EVENT_RTC, 0);
-}
-
-#ifdef CONFIG_X86
-/* Enable use_acpi_alarm mode for Intel platforms no earlier than 2015 */
-static void use_acpi_alarm_quirks(void)
-{
-	if (boot_cpu_data.x86_vendor != X86_VENDOR_INTEL)
-		return;
-
-	if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
-		return;
-
-	if (!is_hpet_enabled())
-		return;
-
-	if (dmi_get_bios_year() < 2015)
-		return;
-
-	use_acpi_alarm = true;
-}
-#else
-static inline void use_acpi_alarm_quirks(void) { }
-#endif
-
-/* Every ACPI platform has a mc146818 compatible "cmos rtc".  Here we find
- * its device node and pass extra config data.  This helps its driver use
- * capabilities that the now-obsolete mc146818 didn't have, and informs it
- * that this board's RTC is wakeup-capable (per ACPI spec).
- */
-static struct cmos_rtc_board_info acpi_rtc_info;
-
-static void cmos_wake_setup(struct device *dev)
-{
-	if (acpi_disabled)
-		return;
-
-	use_acpi_alarm_quirks();
-
-	rtc_wake_setup(dev);
-	acpi_rtc_info.wake_on = rtc_wake_on;
-	acpi_rtc_info.wake_off = rtc_wake_off;
-
-	/* workaround bug in some ACPI tables */
-	if (acpi_gbl_FADT.month_alarm && !acpi_gbl_FADT.day_alarm) {
-		dev_dbg(dev, "bogus FADT month_alarm (%d)\n",
-			acpi_gbl_FADT.month_alarm);
-		acpi_gbl_FADT.month_alarm = 0;
-	}
-
-	acpi_rtc_info.rtc_day_alarm = acpi_gbl_FADT.day_alarm;
-	acpi_rtc_info.rtc_mon_alarm = acpi_gbl_FADT.month_alarm;
-	acpi_rtc_info.rtc_century = acpi_gbl_FADT.century;
-
-	/* NOTE:  S4_RTC_WAKE is NOT currently useful to Linux */
-	if (acpi_gbl_FADT.flags & ACPI_FADT_S4_RTC_WAKE)
-		dev_info(dev, "RTC can wake from S4\n");
-
-	dev->platform_data = &acpi_rtc_info;
-
-	/* RTC always wakes from S1/S2/S3, and often S4/STD */
-	device_init_wakeup(dev, 1);
-}
-
-static void cmos_check_acpi_rtc_status(struct device *dev,
-				       unsigned char *rtc_control)
-{
-	struct cmos_rtc *cmos = dev_get_drvdata(dev);
-	acpi_event_status rtc_status;
-	acpi_status status;
-
-	if (acpi_gbl_FADT.flags & ACPI_FADT_FIXED_RTC)
-		return;
-
-	status = acpi_get_event_status(ACPI_EVENT_RTC, &rtc_status);
-	if (ACPI_FAILURE(status)) {
-		dev_err(dev, "Could not get RTC status\n");
-	} else if (rtc_status & ACPI_EVENT_FLAG_SET) {
-		unsigned char mask;
-		*rtc_control &= ~RTC_AIE;
-		CMOS_WRITE(*rtc_control, RTC_CONTROL);
-		mask = CMOS_READ(RTC_INTR_FLAGS);
-		rtc_update_irq(cmos->rtc, 1, mask);
-	}
-}
-
-#else
-
-static void cmos_wake_setup(struct device *dev)
-{
-}
-
-static void cmos_check_acpi_rtc_status(struct device *dev,
-				       unsigned char *rtc_control)
-{
-}
-
-#endif
-
 #ifdef	CONFIG_PNP
 
 #include <linux/pnp.h>
 
 static int cmos_pnp_probe(struct pnp_dev *pnp, const struct pnp_device_id *id)
 {
-	cmos_wake_setup(&pnp->dev);
+	int irq;
 
 	if (pnp_port_start(pnp, 0) == 0x70 && !pnp_irq_valid(pnp, 0)) {
-		unsigned int irq = 0;
+		irq = 0;
 #ifdef CONFIG_X86
 		/* Some machines contain a PNP entry for the RTC, but
 		 * don't define the IRQ. It should always be safe to
@@ -1308,13 +1384,11 @@
 		if (nr_legacy_irqs())
 			irq = RTC_IRQ;
 #endif
-		return cmos_do_probe(&pnp->dev,
-				pnp_get_resource(pnp, IORESOURCE_IO, 0), irq);
 	} else {
-		return cmos_do_probe(&pnp->dev,
-				pnp_get_resource(pnp, IORESOURCE_IO, 0),
-				pnp_irq(pnp, 0));
+		irq = pnp_irq(pnp, 0);
 	}
+
+	return cmos_do_probe(&pnp->dev, pnp_get_resource(pnp, IORESOURCE_IO, 0), irq);
 }
 
 static void cmos_pnp_remove(struct pnp_dev *pnp)
@@ -1401,7 +1475,6 @@
 	int irq;
 
 	cmos_of_init(pdev);
-	cmos_wake_setup(&pdev->dev);
 
 	if (RTC_IOMAPPED)
 		resource = platform_get_resource(pdev, IORESOURCE_IO, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-ds1302.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-ds1302.c
@@ -199,11 +199,18 @@
 MODULE_DEVICE_TABLE(of, ds1302_dt_ids);
 #endif
 
+static const struct spi_device_id ds1302_spi_ids[] = {
+	{ .name = "ds1302", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, ds1302_spi_ids);
+
 static struct spi_driver ds1302_driver = {
 	.driver.name	= "rtc-ds1302",
 	.driver.of_match_table = of_match_ptr(ds1302_dt_ids),
 	.probe		= ds1302_probe,
 	.remove		= ds1302_remove,
+	.id_table	= ds1302_spi_ids,
 };
 
 module_spi_driver(ds1302_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-ds1347.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-ds1347.c
@@ -112,7 +112,7 @@
 		return err;
 
 	century = (dt->tm_year / 100) + 19;
-	err = regmap_write(map, DS1347_CENTURY_REG, century);
+	err = regmap_write(map, DS1347_CENTURY_REG, bin2bcd(century));
 	if (err)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-ds1390.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-ds1390.c
@@ -219,12 +219,19 @@
 };
 MODULE_DEVICE_TABLE(of, ds1390_of_match);
 
+static const struct spi_device_id ds1390_spi_ids[] = {
+	{ .name = "ds1390" },
+	{}
+};
+MODULE_DEVICE_TABLE(spi, ds1390_spi_ids);
+
 static struct spi_driver ds1390_driver = {
 	.driver = {
 		.name	= "rtc-ds1390",
 		.of_match_table = of_match_ptr(ds1390_of_match),
 	},
 	.probe	= ds1390_probe,
+	.id_table = ds1390_spi_ids,
 };
 
 module_spi_driver(ds1390_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-ds1685.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-ds1685.c
@@ -1438,7 +1438,7 @@
 		unreachable();
 	}
 }
-EXPORT_SYMBOL(ds1685_rtc_poweroff);
+EXPORT_SYMBOL_GPL(ds1685_rtc_poweroff);
 /* ----------------------------------------------------------------------- */
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-ftrtc010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-ftrtc010.c
@@ -137,28 +137,34 @@
 		ret = clk_prepare_enable(rtc->extclk);
 		if (ret) {
 			dev_err(dev, "failed to enable EXTCLK\n");
-			return ret;
+			goto err_disable_pclk;
 		}
 	}
 
-	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (!res)
-		return -ENODEV;
-
-	rtc->rtc_irq = res->start;
+	rtc->rtc_irq = platform_get_irq(pdev, 0);
+	if (rtc->rtc_irq < 0) {
+		ret = rtc->rtc_irq;
+		goto err_disable_extclk;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res)
-		return -ENODEV;
+	if (!res) {
+		ret = -ENODEV;
+		goto err_disable_extclk;
+	}
 
 	rtc->rtc_base = devm_ioremap(dev, res->start,
 				     resource_size(res));
-	if (!rtc->rtc_base)
-		return -ENOMEM;
+	if (!rtc->rtc_base) {
+		ret = -ENOMEM;
+		goto err_disable_extclk;
+	}
 
 	rtc->rtc_dev = devm_rtc_allocate_device(dev);
-	if (IS_ERR(rtc->rtc_dev))
-		return PTR_ERR(rtc->rtc_dev);
+	if (IS_ERR(rtc->rtc_dev)) {
+		ret = PTR_ERR(rtc->rtc_dev);
+		goto err_disable_extclk;
+	}
 
 	rtc->rtc_dev->ops = &ftrtc010_rtc_ops;
 
@@ -174,9 +180,15 @@
 	ret = devm_request_irq(dev, rtc->rtc_irq, ftrtc010_rtc_interrupt,
 			       IRQF_SHARED, pdev->name, dev);
 	if (unlikely(ret))
-		return ret;
+		goto err_disable_extclk;
 
 	return devm_rtc_register_device(rtc->rtc_dev);
+
+err_disable_extclk:
+	clk_disable_unprepare(rtc->extclk);
+err_disable_pclk:
+	clk_disable_unprepare(rtc->pclk);
+	return ret;
 }
 
 static int ftrtc010_rtc_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-isl1208.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-isl1208.c
@@ -743,14 +743,13 @@
 {
 	struct isl1208_state *isl1208 = priv;
 	struct i2c_client *client = to_i2c_client(isl1208->rtc->dev.parent);
-	int ret;
 
 	/* nvmem sanitizes offset/count for us, but count==0 is possible */
 	if (!count)
 		return count;
-	ret = isl1208_i2c_read_regs(client, ISL1208_REG_USR1 + off, buf,
+
+	return isl1208_i2c_read_regs(client, ISL1208_REG_USR1 + off, buf,
 				    count);
-	return ret == 0 ? count : ret;
 }
 
 static int isl1208_nvmem_write(void *priv, unsigned int off, void *buf,
@@ -758,15 +757,13 @@
 {
 	struct isl1208_state *isl1208 = priv;
 	struct i2c_client *client = to_i2c_client(isl1208->rtc->dev.parent);
-	int ret;
 
 	/* nvmem sanitizes off/count for us, but count==0 is possible */
 	if (!count)
 		return count;
-	ret = isl1208_i2c_set_regs(client, ISL1208_REG_USR1 + off, buf,
-				   count);
 
-	return ret == 0 ? count : ret;
+	return isl1208_i2c_set_regs(client, ISL1208_REG_USR1 + off, buf,
+				   count);
 }
 
 static const struct nvmem_config isl1208_nvmem_config = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-mc146818-lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-mc146818-lib.c
@@ -8,10 +8,106 @@
 #include <linux/acpi.h>
 #endif
 
-unsigned int mc146818_get_time(struct rtc_time *time)
+/*
+ * Execute a function while the UIP (Update-in-progress) bit of the RTC is
+ * unset.
+ *
+ * Warning: callback may be executed more then once.
+ */
+bool mc146818_avoid_UIP(void (*callback)(unsigned char seconds, void *param),
+			void *param)
+{
+	int i;
+	unsigned long flags;
+	unsigned char seconds;
+
+	for (i = 0; i < 10; i++) {
+		spin_lock_irqsave(&rtc_lock, flags);
+
+		/*
+		 * Check whether there is an update in progress during which the
+		 * readout is unspecified. The maximum update time is ~2ms. Poll
+		 * every msec for completion.
+		 *
+		 * Store the second value before checking UIP so a long lasting
+		 * NMI which happens to hit after the UIP check cannot make
+		 * an update cycle invisible.
+		 */
+		seconds = CMOS_READ(RTC_SECONDS);
+
+		if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
+			spin_unlock_irqrestore(&rtc_lock, flags);
+			mdelay(1);
+			continue;
+		}
+
+		/* Revalidate the above readout */
+		if (seconds != CMOS_READ(RTC_SECONDS)) {
+			spin_unlock_irqrestore(&rtc_lock, flags);
+			continue;
+		}
+
+		if (callback)
+			callback(seconds, param);
+
+		/*
+		 * Check for the UIP bit again. If it is set now then
+		 * the above values may contain garbage.
+		 */
+		if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
+			spin_unlock_irqrestore(&rtc_lock, flags);
+			mdelay(1);
+			continue;
+		}
+
+		/*
+		 * A NMI might have interrupted the above sequence so check
+		 * whether the seconds value has changed which indicates that
+		 * the NMI took longer than the UIP bit was set. Unlikely, but
+		 * possible and there is also virt...
+		 */
+		if (seconds != CMOS_READ(RTC_SECONDS)) {
+			spin_unlock_irqrestore(&rtc_lock, flags);
+			continue;
+		}
+		spin_unlock_irqrestore(&rtc_lock, flags);
+
+		return true;
+	}
+	return false;
+}
+EXPORT_SYMBOL_GPL(mc146818_avoid_UIP);
+
+/*
+ * If the UIP (Update-in-progress) bit of the RTC is set for more then
+ * 10ms, the RTC is apparently broken or not present.
+ */
+bool mc146818_does_rtc_work(void)
+{
+	int i;
+	unsigned char val;
+	unsigned long flags;
+
+	for (i = 0; i < 10; i++) {
+		spin_lock_irqsave(&rtc_lock, flags);
+		val = CMOS_READ(RTC_FREQ_SELECT);
+		spin_unlock_irqrestore(&rtc_lock, flags);
+
+		if ((val & RTC_UIP) == 0)
+			return true;
+
+		mdelay(1);
+	}
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(mc146818_does_rtc_work);
+
+int mc146818_get_time(struct rtc_time *time)
 {
 	unsigned char ctrl;
 	unsigned long flags;
+	unsigned int iter_count = 0;
 	unsigned char century = 0;
 	bool retry;
 
@@ -20,13 +116,13 @@
 #endif
 
 again:
-	spin_lock_irqsave(&rtc_lock, flags);
-	/* Ensure that the RTC is accessible. Bit 6 must be 0! */
-	if (WARN_ON_ONCE((CMOS_READ(RTC_VALID) & 0x40) != 0)) {
-		spin_unlock_irqrestore(&rtc_lock, flags);
-		memset(time, 0xff, sizeof(*time));
-		return 0;
+	if (iter_count > 10) {
+		memset(time, 0, sizeof(*time));
+		return -EIO;
 	}
+	iter_count++;
+
+	spin_lock_irqsave(&rtc_lock, flags);
 
 	/*
 	 * Check whether there is an update in progress during which the
@@ -104,7 +200,7 @@
 	time->tm_year += real_year - 72;
 #endif
 
-	if (century > 20)
+	if (century > 19)
 		time->tm_year += (century - 19) * 100;
 
 	/*
@@ -116,10 +212,21 @@
 
 	time->tm_mon--;
 
-	return RTC_24H;
+	return 0;
 }
 EXPORT_SYMBOL_GPL(mc146818_get_time);
 
+/* AMD systems don't allow access to AltCentury with DV1 */
+static bool apply_amd_register_a_behavior(void)
+{
+#ifdef CONFIG_X86
+	if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
+	    boot_cpu_data.x86_vendor == X86_VENDOR_HYGON)
+		return true;
+#endif
+	return false;
+}
+
 /* Set the current date and time in the real time clock. */
 int mc146818_set_time(struct rtc_time *time)
 {
@@ -176,8 +283,10 @@
 	if (yrs >= 100)
 		yrs -= 100;
 
-	if (!(CMOS_READ(RTC_CONTROL) & RTC_DM_BINARY)
-	    || RTC_ALWAYS_BCD) {
+	spin_lock_irqsave(&rtc_lock, flags);
+	save_control = CMOS_READ(RTC_CONTROL);
+	spin_unlock_irqrestore(&rtc_lock, flags);
+	if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
 		sec = bin2bcd(sec);
 		min = bin2bcd(min);
 		hrs = bin2bcd(hrs);
@@ -191,7 +300,10 @@
 	save_control = CMOS_READ(RTC_CONTROL);
 	CMOS_WRITE((save_control|RTC_SET), RTC_CONTROL);
 	save_freq_select = CMOS_READ(RTC_FREQ_SELECT);
-	CMOS_WRITE((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT);
+	if (apply_amd_register_a_behavior())
+		CMOS_WRITE((save_freq_select & ~RTC_AMD_BANK_SELECT), RTC_FREQ_SELECT);
+	else
+		CMOS_WRITE((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT);
 
 #ifdef CONFIG_MACH_DECSTATION
 	CMOS_WRITE(real_yrs, RTC_DEC_YEAR);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-mcp795.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-mcp795.c
@@ -430,12 +430,19 @@
 MODULE_DEVICE_TABLE(of, mcp795_of_match);
 #endif
 
+static const struct spi_device_id mcp795_spi_ids[] = {
+	{ .name = "mcp795" },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, mcp795_spi_ids);
+
 static struct spi_driver mcp795_driver = {
 		.driver = {
 				.name = "rtc-mcp795",
 				.of_match_table = of_match_ptr(mcp795_of_match),
 		},
 		.probe = mcp795_probe,
+		.id_table = mcp795_spi_ids,
 };
 
 module_spi_driver(mcp795_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-meson-vrtc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-meson-vrtc.c
@@ -23,7 +23,7 @@
 	struct timespec64 time;
 
 	dev_dbg(dev, "%s\n", __func__);
-	ktime_get_raw_ts64(&time);
+	ktime_get_real_ts64(&time);
 	rtc_time64_to_tm(time.tv_sec, tm);
 
 	return 0;
@@ -96,7 +96,7 @@
 		long alarm_secs;
 		struct timespec64 time;
 
-		ktime_get_raw_ts64(&time);
+		ktime_get_real_ts64(&time);
 		local_time = time.tv_sec;
 
 		dev_dbg(dev, "alarm_time = %lus, local_time=%lus\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-mt6397.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-mt6397.c
@@ -269,6 +269,8 @@
 		return -ENOMEM;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
 	rtc->addr_base = res->start;
 
 	rtc->data = of_device_get_match_data(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-mxc_v2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-mxc_v2.c
@@ -336,8 +336,10 @@
 	}
 
 	pdata->rtc = devm_rtc_allocate_device(&pdev->dev);
-	if (IS_ERR(pdata->rtc))
+	if (IS_ERR(pdata->rtc)) {
+		clk_disable_unprepare(pdata->clk);
 		return PTR_ERR(pdata->rtc);
+	}
 
 	pdata->rtc->ops = &mxc_rtc_ops;
 	pdata->rtc->range_max = U32_MAX;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-omap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-omap.c
@@ -25,6 +25,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/rtc.h>
+#include <linux/rtc/rtc-omap.h>
 
 /*
  * The OMAP RTC is a year/month/day/hours/minutes/seconds BCD clock
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pcf2123.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pcf2123.c
@@ -451,12 +451,21 @@
 MODULE_DEVICE_TABLE(of, pcf2123_dt_ids);
 #endif
 
+static const struct spi_device_id pcf2123_spi_ids[] = {
+	{ .name = "pcf2123", },
+	{ .name = "rv2123", },
+	{ .name = "rtc-pcf2123", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, pcf2123_spi_ids);
+
 static struct spi_driver pcf2123_driver = {
 	.driver	= {
 			.name	= "rtc-pcf2123",
 			.of_match_table = of_match_ptr(pcf2123_dt_ids),
 	},
 	.probe	= pcf2123_probe,
+	.id_table = pcf2123_spi_ids,
 };
 
 module_spi_driver(pcf2123_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pcf2127.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pcf2127.c
@@ -374,7 +374,8 @@
 static int pcf2127_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
 {
 	struct pcf2127 *pcf2127 = dev_get_drvdata(dev);
-	unsigned int buf[5], ctrl2;
+	u8 buf[5];
+	unsigned int ctrl2;
 	int ret;
 
 	ret = regmap_read(pcf2127->regmap, PCF2127_REG_CTRL2, &ctrl2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pcf85063.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pcf85063.c
@@ -167,10 +167,10 @@
 	if (ret)
 		return ret;
 
-	alrm->time.tm_sec = bcd2bin(buf[0]);
-	alrm->time.tm_min = bcd2bin(buf[1]);
-	alrm->time.tm_hour = bcd2bin(buf[2]);
-	alrm->time.tm_mday = bcd2bin(buf[3]);
+	alrm->time.tm_sec = bcd2bin(buf[0] & 0x7f);
+	alrm->time.tm_min = bcd2bin(buf[1] & 0x7f);
+	alrm->time.tm_hour = bcd2bin(buf[2] & 0x3f);
+	alrm->time.tm_mday = bcd2bin(buf[3] & 0x3f);
 
 	ret = regmap_read(pcf85063->regmap, PCF85063_REG_CTRL2, &val);
 	if (ret)
@@ -320,7 +320,16 @@
 static int pcf85063_nvmem_read(void *priv, unsigned int offset,
 			       void *val, size_t bytes)
 {
-	return regmap_read(priv, PCF85063_REG_RAM, val);
+	unsigned int tmp;
+	int ret;
+
+	ret = regmap_read(priv, PCF85063_REG_RAM, &tmp);
+	if (ret < 0)
+		return ret;
+
+	*(u8 *)val = tmp;
+
+	return 0;
 }
 
 static int pcf85063_nvmem_write(void *priv, unsigned int offset,
@@ -422,7 +431,7 @@
 	unsigned int buf;
 	int ret;
 
-	ret = regmap_read(pcf85063->regmap, PCF85063_REG_OFFSET, &buf);
+	ret = regmap_read(pcf85063->regmap, PCF85063_REG_CTRL2, &buf);
 	if (ret < 0)
 		return ret;
 	buf &= PCF85063_REG_CLKO_F_MASK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pcf85263.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pcf85263.c
@@ -0,0 +1,1784 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NXP PCF85263 RTC driver
+ * Copyright (C) 2015 Eurotech Ltd Fabrizio Castro
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; If not, see <http://www.gnu.org/licenses/>
+ */
+#define DEBUG 0
+
+#include <linux/i2c.h>
+#include <linux/bcd.h>
+#include <linux/rtc.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+#include <linux/watchdog.h>
+#include <linux/pm.h>
+#include <linux/pm_wakeup.h>
+#include <linux/io.h>
+#include "rtc-pcf85263.h"
+
+/*
+ * This driver implements only a subset of the HW capabilities:
+ * - RTC
+ * - Alarm 1
+ * - watchdog
+ * - timestamps
+ * - RAM byte
+ * - Battery management
+ * - Oscillator
+ */
+/*
+ * workaround for the sleep/wakeup issue
+ * resuming from sleep we need to set the gpio0_19 bit
+ * in this registers. Due to pcb routing there is no need
+ * to configure something
+ */
+#define GPIO0_IRQSTATUS_0_ADDR	0x44E0702C
+#define GPIO0_IRQSTATUS_1_ADDR	0x44E07030
+#define GPIO0_19_SET_BIT_ACK	0x00080000
+
+#define RTC_WAIT_FOR_INTERRUPTS     _IOW('p', 0x15, unsigned char)
+#define RTC_WAIT_FOR_ANY_INTERRUPT  _IOR('p', 0x16, unsigned char)
+#define RTC_CLEAR_INTERRUPT_FLAGS   _IOW('p', 0x17, unsigned char)
+
+#define WATCHDOG_TIMEOUT	60
+#define TAMPER_LEVEL		1
+#define VOLTAGE_THRE		0
+#define WDT_ENABLE		0
+#define WAKE_ENABLE		1
+#define INT_BATT_DEF		"INTA"
+#define INT_WDT_DEF		"NO_INTERRUPT"
+#define INT_TST_DEF		"INTB"
+#define INT_APM_DEF		"INTAPM_INTA"
+#define TSPM_DEF		"TSPM_INPUT_MODE"
+
+static int timeout = WATCHDOG_TIMEOUT;
+module_param(timeout, int, 0);
+MODULE_PARM_DESC(timeout,
+		 "Watchdog timeout in seconds. (1<=timeout<=124, default="
+		 __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+
+static bool nowayout = WATCHDOG_NOWAYOUT;
+module_param(nowayout, bool, 0);
+MODULE_PARM_DESC(nowayout,
+		 "Watchdog cannot be stopped once started (default="
+		 __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+
+static bool tsl = TAMPER_LEVEL;
+module_param(tsl, bool, 0);
+MODULE_PARM_DESC(tsl,
+		 "Tamper level, 0 low, 1 high (default="
+		 __MODULE_STRING(TAMPER_LEVEL) ")");
+
+static bool vth = VOLTAGE_THRE;
+module_param(vth, bool, 0);
+MODULE_PARM_DESC(vth,
+		 "Voltage threshold level, 0 -> 1.5V, 1 -> 2.8V (default="
+		 __MODULE_STRING(VOLTAGE_THRE) ")");
+
+static bool wdten = WDT_ENABLE;
+module_param(wdten, bool, 0);
+MODULE_PARM_DESC(wdten,
+		 "Watchdog timer enable, 0 disabled, 1 enabled (default="
+		 __MODULE_STRING(WDT_ENABLE) ")");
+
+static bool wakeen = WAKE_ENABLE;
+module_param(wakeen, bool, 0);
+MODULE_PARM_DESC(wakeen,
+		 "Wakeup function enable, 0 disabled, 1 enabled (default="
+		 __MODULE_STRING(WAKE_ENABLE) ")");
+
+static char *int_batt = INT_BATT_DEF;
+module_param(int_batt, charp, 0);
+MODULE_PARM_DESC(int_batt,
+		 "Battery connection configuration, INTA, INTB, NO_INTERRUPT (default="
+		 __MODULE_STRING(INT_BATT_DEF) ")");
+
+static char *int_wdt = INT_WDT_DEF;
+module_param(int_wdt, charp, 0);
+MODULE_PARM_DESC(int_wdt,
+		 "Watchdog connection configuration, INTA, INTB, NO_INTERRUPT (default="
+		 __MODULE_STRING(INT_WDT_DEF) ")");
+
+static char *int_tst = INT_TST_DEF;
+module_param(int_tst, charp, 0);
+MODULE_PARM_DESC(int_tst,
+		 "Timestamp connection configuration, INTA, INTB, NO_INTERRUPT (default="
+		 __MODULE_STRING(INT_TST_DEF) ")");
+
+static char *intapm_conf = INT_APM_DEF;
+module_param(intapm_conf, charp, 0);
+MODULE_PARM_DESC(intapm_conf,
+		 "INTA Pin mode, INTAPM_CLK_OUTPUT, INTAPM_BATTERY_MODE_INDICATION, INTAPM_INTA, INTAPM_HIGH_IMPEDANCE (default="
+		 __MODULE_STRING(INT_APM_DEF) ")");
+
+static char *tspm = TSPM_DEF;
+module_param(tspm, charp, 0);
+MODULE_PARM_DESC(tspm,
+		 "Timestamp pin mode, TSPM_DISABLED, TSPM_INT, TSPM_CLK_OUTPUT, TSPM_INPUT_MODE (default="
+		 __MODULE_STRING(TSPM_DEF) ")");
+
+static struct i2c_driver pcf85263_driver;
+
+struct pcf85263 {
+	struct i2c_client *client;
+	struct rtc_device *rtc;
+	struct mutex mutex;
+	int ram_byte_file_created;
+	int registers_file_created;
+	int resets_file_created;
+	int inta_gpio;
+	int intb_gpio;
+	int inta_irq;
+	int intb_irq;
+	int interrupt_alarm;
+	int clock_frequency;
+	int clk_pin;
+	int inta_pin;
+	int ts_pin;
+	int ts_pin_pull;
+	int ts_pin_level;
+	int ts_pin_input_type;
+	int watchdog_timeout;
+	int watchdog_disable_on_boot;
+	int interrupt_watchdog;
+	int flags_file_created;
+	int timestamp1_file_created;
+	int timestamp2_file_created;
+	int timestamp3_file_created;
+	int timestamp1_mode;
+	int timestamp2_mode;
+	int timestamp3_mode;
+	int interrupt_timestamp;
+	int battery_switch;
+	int battery_vth;
+	int interrupt_battery;
+	wait_queue_head_t event_queue;
+	unsigned char event_interrupt;
+	struct work_struct work;
+	int irq;
+};
+
+/*******************************************************************************
+ *  Utils
+ */
+static int pcf85263_read_register(struct i2c_client *client,
+				  unsigned char address,
+				  unsigned char *value)
+{
+	int err;
+
+	err = i2c_master_send(client, &address, sizeof(address));
+	if (err != sizeof(address))
+		return err;
+	err = i2c_master_recv(client, value, sizeof(unsigned char));
+	if (err != sizeof(unsigned char))
+		return err;
+	return 0;
+}
+
+static int pcf85263_read_registers(struct i2c_client *client,
+				   unsigned char address,
+				   unsigned char *values, int count)
+{
+	int err;
+
+	err = i2c_master_send(client, &address, sizeof(address));
+	if (err != sizeof(address))
+		return err;
+	err = i2c_master_recv(client, values, count);
+	if (err != count)
+		return err;
+	return 0;
+}
+
+static int pcf85263_write_register(struct i2c_client *client,
+				   unsigned char address,
+				   unsigned char value)
+{
+	int err;
+	unsigned char data[2] = { address, value };
+
+	err = i2c_master_send(client, data, sizeof(data));
+	if (err != sizeof(data))
+		return err;
+	return 0;
+}
+
+static int pcf85263_first_one_index(unsigned char value)
+{
+	int first_one_index = 0;
+
+	if (value == 0)
+		return -EINVAL;
+	while ((value & 0x01) == 0) {
+		value = value >> 1;
+		first_one_index++;
+	}
+	return first_one_index;
+}
+
+/*******************************************************************************
+ * Watchdog
+ */
+
+static int pcf85263_watchdog_enable(struct i2c_client *client, int enable)
+{
+	int err = 0;
+	unsigned char value;
+	struct pcf85263 *pcf85263;
+
+	pcf85263 = i2c_get_clientdata(client);
+	if (pcf85263->interrupt_watchdog == INTA) {
+		err =
+		    pcf85263_read_register(client, REGISTER_INTA_ENABLE,
+					   &value);
+		if (err)
+			return err;
+		value &= ~WDIEA;
+		value |= (enable ? WDIEA_ENABLE : WDIEA_DISABLE);
+		err =
+		    pcf85263_write_register(client, REGISTER_INTA_ENABLE,
+					    value);
+	} else if (pcf85263->interrupt_watchdog == INTB) {
+		err =
+		    pcf85263_read_register(client, REGISTER_INTB_ENABLE,
+					   &value);
+		if (err)
+			return err;
+		value &= ~WDIEB;
+		value |= (enable ? WDIEB_ENABLE : WDIEB_DISABLE);
+		err =
+		    pcf85263_write_register(client, REGISTER_INTB_ENABLE,
+					    value);
+	} else {
+		dev_dbg(&client->dev, "[%s] no interrupt registered\n",
+			__func__);
+	}
+	return err;
+}
+
+static int pcf85263_watchdog_compute_seconds(int *seconds,
+					     unsigned char *_wdr_value,
+					     unsigned char *_wds_value)
+{
+	unsigned char wdr_value, wds_value;
+
+	/* WatchDog-duration = WDR x stepsize */
+	if (*seconds > 120) {
+		wdr_value = 31;
+		wds_value = WDS_4_SECONDS;
+	} else if (*seconds > 31) {
+		wdr_value = (unsigned char)(*seconds / 4);
+		if (((int)wdr_value * 4) != *seconds)
+			wdr_value++;
+		wds_value = WDS_4_SECONDS;
+	} else if (*seconds >= 0) {
+		wdr_value = (unsigned char)*seconds;
+		wds_value = WDS_1_SECOND;
+	} else {
+		return -EINVAL;
+	}
+	if (wds_value == WDS_4_SECONDS)
+		*seconds = (int)wdr_value * 4;
+	else
+		*seconds = wdr_value;
+	if (_wdr_value)
+		*_wdr_value = wdr_value;
+
+	if (_wds_value)
+		*_wds_value = wds_value;
+	return 0;
+}
+
+static int pcf85263_watchdog_set_time(struct i2c_client *client,
+				      int *seconds)
+{
+	int err;
+	unsigned char wdr_value, wds_value, value;
+	struct pcf85263 *pcf85263;
+
+	dev_dbg(&client->dev, "[%s] [input] seconds = %d\n", __func__,
+		*seconds);
+	pcf85263 = i2c_get_clientdata(client);
+	err =
+	    pcf85263_watchdog_compute_seconds(seconds, &wdr_value,
+					      &wds_value);
+	if (err) {
+		dev_dbg(&client->dev,
+			"[%s] problems while computing actual timeout\n",
+			__func__);
+		return err;
+	}
+	err = pcf85263_read_register(client, REGISTER_WATCHDOG, &value);
+	if (err)
+		return err;
+	value &= ~WDR;
+	value |= (wdr_value << pcf85263_first_one_index(WDR));
+	value &= ~WDS;
+	value |= (wds_value << pcf85263_first_one_index(WDS));
+	err = pcf85263_write_register(client, REGISTER_WATCHDOG, value);
+	if (err)
+		return err;
+	dev_dbg(&client->dev, "[%s] [output] seconds = %d\n", __func__,
+		*seconds);
+	return 0;
+}
+
+static int pcf85263_watchdog_get_current_time(struct i2c_client *client,
+					      int *seconds)
+{
+	int err = 0;
+	unsigned char wdr_value, wds_value, value;
+	struct pcf85263 *pcf85263;
+
+	pcf85263 = i2c_get_clientdata(client);
+	err = pcf85263_read_register(client, REGISTER_WATCHDOG, &value);
+	if (err)
+		return err;
+	wdr_value = (value & WDR) >> pcf85263_first_one_index(WDR);
+	wds_value = (value & WDS) >> pcf85263_first_one_index(WDS);
+	if (wds_value == WDS_4_SECONDS)
+		*seconds = wdr_value * 4;
+	else if (wds_value == WDS_1_SECOND)
+		*seconds = wdr_value;
+	else
+		err = -EILSEQ;
+
+	return err;
+}
+
+static int pcf85263_watchdog_ping(struct i2c_client *client)
+{
+	struct pcf85263 *pcf85263 = i2c_get_clientdata(client);
+
+	return pcf85263_watchdog_set_time(client,
+					  &pcf85263->watchdog_timeout);
+}
+
+/*
+ * Watchdog subsystem
+ */
+static int pcf85263_watchdog_start_op(struct watchdog_device *device)
+{
+	int err;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = watchdog_get_drvdata(device);
+	pcf85263 = i2c_get_clientdata(client);
+
+	mutex_lock(&pcf85263->mutex);
+	err =
+	    pcf85263_watchdog_set_time(client,
+				       &pcf85263->watchdog_timeout);
+	if (err)
+		goto exit;
+	err = pcf85263_watchdog_enable(client, 1);
+exit:
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+static int pcf85263_watchdog_stop_op(struct watchdog_device *device)
+{
+	int err, seconds = 0;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = watchdog_get_drvdata(device);
+	pcf85263 = i2c_get_clientdata(client);
+
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_watchdog_enable(client, 0);
+	if (err)
+		goto exit;
+	err = pcf85263_watchdog_set_time(client, &seconds);
+exit:
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+static int pcf85263_watchdog_ping_op(struct watchdog_device *device)
+{
+	int err;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = watchdog_get_drvdata(device);
+	pcf85263 = i2c_get_clientdata(client);
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_watchdog_ping(client);
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+static int pcf85263_watchdog_set_timeout_op(struct watchdog_device *device,
+					    unsigned int timeout)
+{
+	int seconds, err;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = watchdog_get_drvdata(device);
+	pcf85263 = i2c_get_clientdata(client);
+	seconds = (int)timeout;
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_watchdog_compute_seconds(&seconds, NULL, NULL);
+	if (!err) {
+		device->timeout = (unsigned int)seconds;
+		pcf85263->watchdog_timeout = seconds;
+	}
+	mutex_unlock(&pcf85263->mutex);
+	return 0;
+}
+
+static unsigned int pcf85263_watchdog_get_timeleft_op(struct
+						      watchdog_device
+						      * device)
+{
+	int err, seconds = 0;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = watchdog_get_drvdata(device);
+	pcf85263 = i2c_get_clientdata(client);
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_watchdog_get_current_time(client, &seconds);
+	mutex_unlock(&pcf85263->mutex);
+	return (unsigned int)seconds;
+}
+
+static struct watchdog_info pcf85263_watchdog_info = {
+	.options =
+	    WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE,
+	.identity = "PCF85263 Watchdog",
+};
+
+static struct watchdog_ops pcf85263_watchdog_ops = {
+	.owner = THIS_MODULE,
+	.start = pcf85263_watchdog_start_op,
+	.stop = pcf85263_watchdog_stop_op,
+	.ping = pcf85263_watchdog_ping_op,
+	.set_timeout = pcf85263_watchdog_set_timeout_op,
+	.get_timeleft = pcf85263_watchdog_get_timeleft_op,
+};
+
+static struct watchdog_device pcf85263_watchdog_device = {
+	.info = &pcf85263_watchdog_info,
+	.ops = &pcf85263_watchdog_ops,
+	.timeout = WATCHDOG_TIMEOUT,
+	.min_timeout = 1,
+	.max_timeout = 124,
+};
+
+/*******************************************************************************
+ * Timestamps
+ */
+static int pcf85263_read_timestamp(struct device *dev, int tsr_number,
+				   int *seconds, int *minutes, int *hours,
+				   int *days, int *months, int *years)
+{
+	int err;
+	unsigned char tsr_register, values[6];
+	struct i2c_client *client = to_i2c_client(dev);
+
+	if (tsr_number < 1 || tsr_number > 3)
+		return -EINVAL;
+	if (tsr_number == 1)
+		tsr_register = REGISTER_TSR1_SECONDS;
+	else if (tsr_number == 2)
+		tsr_register = REGISTER_TSR2_SECONDS;
+	else
+		tsr_register = REGISTER_TSR3_SECONDS;
+	err =
+	    pcf85263_read_registers(client, tsr_register, values,
+				    sizeof(values));
+	if (err)
+		return err;
+	*seconds = bcd2bin(values[0] & SECONDS_BITS);
+	*minutes = bcd2bin(values[1] & MINUTES_BITS);
+	*hours = bcd2bin(values[2] & HOURS_BITS);
+	*days = bcd2bin(values[3] & DAYS_BITS);
+	*months = bcd2bin(values[4] & MONTHS_BITS);
+	*years = bcd2bin(values[5] & YEARS_BITS) + 2000;
+	return 0;
+}
+
+static ssize_t pcf85263_timestamp_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf, int tsr_number)
+{
+	int err, seconds = 0, minutes = 0, hours = 0, days = 0, months = 0,
+	    years = 0;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+	unsigned char value;
+	char *event_message;
+	char *no_timestamp_defined = "No timestamp defined";
+	char *first_ts_event = "First TS event";
+	char *last_ts_event = "Last TS event";
+	char *first_switch_to_battery = "First switch to battery";
+	char *last_switch_to_battery = "Last switch to battery";
+	char *last_switch_to_vdd = "Last switch to Vdd";
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	dev_dbg(&client->dev, "[%s] timestamp %d\n", __func__, tsr_number);
+
+	mutex_lock(&pcf85263->mutex);
+	err =
+	    pcf85263_read_timestamp(dev, tsr_number, &seconds, &minutes,
+				    &hours, &days, &months, &years);
+	if (!err)
+		err =
+		    pcf85263_read_register(client, REGISTER_TSR_MODE,
+					   &value);
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	if (tsr_number == 1) {
+		switch (value & TSR1M) {
+		case TSR1M_FIRST_TS_EVENT:
+			event_message = first_ts_event;
+			break;
+		case TSR1M_LAST_TS_EVENT:
+			event_message = last_ts_event;
+			break;
+		default:
+			event_message = no_timestamp_defined;
+		}
+	} else if (tsr_number == 2) {
+		switch (value & TSR2M) {
+		case TSR2M_FIRST_TS_EVENT:
+			event_message = first_ts_event;
+			break;
+		case TSR2M_LAST_TS_EVENT:
+			event_message = last_ts_event;
+			break;
+		case TSR2M_FIRST_SWITCH_TO_BATTERY:
+			event_message = first_switch_to_battery;
+			break;
+		case TSR2M_LAST_SWITCH_TO_BATTERY:
+			event_message = last_switch_to_battery;
+			break;
+		case TSR2M_LAST_SWITCH_TO_VDD:
+			event_message = last_switch_to_vdd;
+			break;
+		default:
+			event_message = no_timestamp_defined;
+		}
+	} else {
+		switch (value & TSR3M) {
+		case TSR3M_FIRST_SWITCH_TO_BATTERY:
+			event_message = first_switch_to_battery;
+			break;
+		case TSR3M_LAST_SWITCH_TO_BATTERY:
+			event_message = last_switch_to_battery;
+			break;
+		case TSR3M_LAST_SWITCH_TO_VDD:
+			event_message = last_switch_to_vdd;
+			break;
+		default:
+			event_message = no_timestamp_defined;
+		}
+	}
+
+	if (days == 0) {
+		return sprintf(buf,
+			       "yyyy/mm/dd hh:mm:ss Event\n----/--/-- --:--:-- %s\n",
+			       event_message);
+	} else {
+		return sprintf(buf,
+			       "yyyy/mm/dd hh:mm:ss Event\n%04d/%02d/%02d %02d:%02d:%02d %s\n",
+			       years, months, days, hours, minutes,
+			       seconds, event_message);
+	}
+}
+
+//================================================================================================
+static ssize_t pcf85263_flags_show(struct device *dev,
+				   struct device_attribute *attr,
+				   char *buf)
+{
+	unsigned char value;
+	struct i2c_client *client;
+
+	client = to_i2c_client(dev);
+
+	if (pcf85263_read_register(client, REGISTER_FLAGS, &value) == 0)
+		return sprintf(buf, "%d\n", value);
+
+	return -1;
+}
+
+static ssize_t pcf85263_flags_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	int n;
+	unsigned char value;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	value = 0;
+	for (n = 0; n < count; n++) {
+		if ((*buf >= '0') && (*buf <= '9'))
+			value = (value * 10) + (*buf++ - '0');
+	}
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	if (value != 0) {
+		mutex_lock(&pcf85263->mutex);
+		if (pcf85263_write_register(client, REGISTER_FLAGS, value ^ 0xff) == 0) {
+			mutex_unlock(&pcf85263->mutex);
+			return count;
+		}
+		mutex_unlock(&pcf85263->mutex);
+	}
+	return -1;
+}
+
+static const struct device_attribute pcf85263_flags_attribute = {
+	.attr.name	= "flags",
+	.attr.mode	= 0600,
+	.show		= pcf85263_flags_show,
+	.store		= pcf85263_flags_store,
+};
+
+static ssize_t pcf85263_timestamp1_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	return pcf85263_timestamp_show(dev, attr, buf, 1);
+}
+
+static const struct device_attribute pcf85263_timestamp1_attribute = {
+	.attr.name	= "timestamp1",
+	.attr.mode	= 0400,
+	.show		= pcf85263_timestamp1_show,
+};
+
+static ssize_t pcf85263_timestamp2_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	return pcf85263_timestamp_show(dev, attr, buf, 2);
+}
+
+static const struct device_attribute pcf85263_timestamp2_attribute = {
+	.attr.name = "timestamp2",
+	.attr.mode = 0400,
+	.show = pcf85263_timestamp2_show,
+};
+
+static ssize_t pcf85263_timestamp3_show(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	return pcf85263_timestamp_show(dev, attr, buf, 3);
+}
+
+static const struct device_attribute pcf85263_timestamp3_attribute = {
+	.attr.name = "timestamp3",
+	.attr.mode = 0400,
+	.show = pcf85263_timestamp3_show,
+
+};
+
+/*******************************************************************************
+ * Resets
+ */
+static ssize_t pcf85263_resets_show(struct device *dev,
+				    struct device_attribute *attr,
+				    char *buf)
+{
+	return sprintf(buf, "software prescaler timestamps\n");
+}
+
+static ssize_t pcf85263_resets_store(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t count)
+{
+	int err = 0;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+	char buffer[11];
+	size_t chars_count;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	if (count < 8 || count > 11 || (count == 11 && buf[count - 1] != '\n'))
+		return -EINVAL;
+
+	chars_count = count;
+	if (buf[count - 1] == '\n')
+		chars_count--;
+	memcpy(buffer, buf, chars_count);
+	buffer[chars_count] = '\0';
+	mutex_lock(&pcf85263->mutex);
+	if (strcmp(buffer, "software") == 0) {
+		err =
+		    pcf85263_write_register(client, REGISTER_RESETS,
+					    SR_CMD);
+	} else if (strcmp(buffer, "prescaler") == 0) {
+		err =
+		    pcf85263_write_register(client, REGISTER_RESETS,
+					    CPR_CMD);
+	} else if (strcmp(buffer, "timestamps") == 0) {
+		err =
+		    pcf85263_write_register(client, REGISTER_RESETS,
+					    CTS_CMD);
+	} else {
+		err = -EINVAL;
+	}
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	return count;
+}
+
+static const struct device_attribute pcf85263_resets_attribute = {
+	.attr.name = "resets",
+	.attr.mode = S_IRUSR | S_IWUSR,
+	.show = pcf85263_resets_show,
+	.store = pcf85263_resets_store,
+};
+
+/*******************************************************************************
+ * RTC
+ */
+static int pcf85263_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+	int err;
+	unsigned char data[8];
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+
+	mutex_lock(&pcf85263->mutex);
+	err =
+	    pcf85263_read_registers(client, REGISTER_CENTS_OF_SECOND, data,
+				    sizeof(data));
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	tm->tm_sec = bcd2bin(data[REGISTER_SECONDS] & SECONDS_BITS);
+	tm->tm_min = bcd2bin(data[REGISTER_MINUTES] & MINUTES_BITS);
+	tm->tm_hour = bcd2bin(data[REGISTER_HOURS] & HOURS_BITS);
+	tm->tm_mday = bcd2bin(data[REGISTER_DAYS] & DAYS_BITS);
+	tm->tm_mon = bcd2bin(data[REGISTER_MONTHS] & MONTHS_BITS) - 1;
+	tm->tm_year = bcd2bin(data[REGISTER_YEARS] & YEARS_BITS) + 100;
+	tm->tm_wday = bcd2bin(data[REGISTER_WEEKDAYS] & WEEKDAYS_BITS);
+	tm->tm_yday = rtc_year_days(tm->tm_mday, tm->tm_mon, tm->tm_year);
+	/* Daylight Saving Time */
+	tm->tm_isdst = -1;
+	if (rtc_valid_tm(tm) < 0)
+		dev_err(dev, "retrieved date/time is not valid.\n");
+	return 0;
+}
+
+static int pcf85263_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+	int err;
+	unsigned char data[11];
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	if (tm->tm_year < 100)
+		return -EINVAL;
+	data[0] = REGISTER_STOP_ENABLE;
+	data[1] = STOP_RTC_STOPPED;
+	data[2] = CPR_CMD;
+	data[3] = 0;		// cents of second
+	data[4] = bin2bcd(tm->tm_sec); // this will clear OS bit as well,
+	// which makes the oscillator start
+	// if it was stopped
+	data[5] = bin2bcd(tm->tm_min);
+	data[6] = bin2bcd(tm->tm_hour);
+	data[7] = bin2bcd(tm->tm_mday);
+	data[8] = bin2bcd(tm->tm_wday);
+	data[9] = bin2bcd(tm->tm_mon + 1);
+	data[10] = bin2bcd(tm->tm_year - 100);
+	mutex_lock(&pcf85263->mutex);
+	err = i2c_master_send(client, data, sizeof(data));
+	if (err != sizeof(data))
+		err = -EIO;
+	else
+		err =
+		    pcf85263_write_register(client, REGISTER_STOP_ENABLE,
+					    STOP_RTC_RUN);
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+/*******************************************************************************
+ * Alarm
+ */
+
+static int pcf85263_rtc_alarm_irq_enable(struct device *dev,
+					 unsigned int enabled)
+{
+	int err = 0;
+	unsigned char value;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	dev_dbg(&client->dev, "[%s] enabled = %u\n", __func__, enabled);
+	mutex_lock(&pcf85263->mutex);
+	if (pcf85263->interrupt_alarm != NO_INTERRUPT) {
+		/* enable/disable alarm1 */
+		if (pcf85263_read_register
+		    (client, REGISTER_ALARM_ENABLES, &value))
+			goto exit;
+		if (enabled)
+			value = (value & ~(ALARM1_BITS)) | ALARM1_ENABLE;
+		else
+			value = (value & ~(ALARM1_BITS)) | ALARM1_DISABLE;
+		if (pcf85263_write_register
+		    (client, REGISTER_ALARM_ENABLES, value))
+			goto exit;
+		/* enabled/disable irq for alarm1 */
+		if (pcf85263->interrupt_alarm == INTA) {
+			if (pcf85263_read_register
+			    (client, REGISTER_INTA_ENABLE, &value))
+				goto exit;
+			value &= ~A1IEA;
+			value |= (enabled ? A1IEA_ENABLE : A1IEA_DISABLE);
+			value &= ~ILPA;
+			value |= ILPA_PERMANENT_SIGNAL;
+			if (pcf85263_write_register
+			    (client, REGISTER_INTA_ENABLE, value))
+				goto exit;
+		} else {
+			if (pcf85263_read_register
+			    (client, REGISTER_INTB_ENABLE, &value))
+				goto exit;
+			value &= ~A1IEB;
+			value |= (enabled ? A1IEB_ENABLE : A1IEB_DISABLE);
+			value &= ~ILPB;
+			value |= ILPB_PERMANENT_SIGNAL;
+			if (pcf85263_write_register
+			    (client, REGISTER_INTB_ENABLE, value))
+				goto exit;
+		}
+		/* clean up interrupt flag when disabling */
+		if (!enabled) {
+			if (pcf85263_read_register
+			    (client, REGISTER_FLAGS, &value))
+				goto exit;
+			value =
+			    (value & ~(ALARM1_FLAG)) | ALARM1_FLAG_CLEAR;
+			if (pcf85263_write_register
+			    (client, REGISTER_FLAGS, value))
+				goto exit;
+		}
+	}
+exit:
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+static int pcf85263_rtc_read_alarm(struct device *dev,
+				   struct rtc_wkalrm *alarm)
+{
+	int err;
+	unsigned char data[5];
+	unsigned char value;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_read_registers(client, REGISTER_SECOND_ALARM1, data,
+				      sizeof(data));
+	if (err)
+		goto exit;
+	alarm->time.tm_sec = bcd2bin(data[0] & SECONDS_BITS);
+	alarm->time.tm_min = bcd2bin(data[1] & MINUTES_BITS);
+	alarm->time.tm_hour = bcd2bin(data[2] & HOURS_BITS);
+	alarm->time.tm_mday = bcd2bin(data[3] & DAYS_BITS);
+	alarm->time.tm_mon = bcd2bin(data[4] & MONTHS_BITS) - 1;
+	err =
+	    pcf85263_read_register(client, REGISTER_ALARM_ENABLES, &value);
+	if (err)
+		goto exit;
+	alarm->enabled = ((value & ALARM1_BITS) == ALARM1_ENABLE) ?
+	    ALARM_ENABLED : ALARM_DISABLED;
+exit:
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+static int pcf85263_rtc_set_alarm(struct device *dev,
+				  struct rtc_wkalrm *alarm)
+{
+	int err;
+	unsigned char data[6];
+	unsigned char value;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	data[0] = REGISTER_SECOND_ALARM1;
+	data[1] = bin2bcd(alarm->time.tm_sec);
+	data[2] = bin2bcd(alarm->time.tm_min);
+	data[3] = bin2bcd(alarm->time.tm_hour);
+	data[4] = bin2bcd(alarm->time.tm_mday);
+	data[5] = bin2bcd(alarm->time.tm_mon + 1);
+	mutex_lock(&pcf85263->mutex);
+	err = i2c_master_send(client, data, sizeof(data));
+	if (err != sizeof(data)) {
+		err = -EIO;
+		goto exit;
+	}
+	if (alarm->enabled) {
+		err =
+		    pcf85263_write_register(client, REGISTER_ALARM_ENABLES,
+					    ALARM1_ENABLE |
+					    ALARM2_DISABLE);
+	} else {
+		err =
+		    pcf85263_write_register(client, REGISTER_ALARM_ENABLES,
+					    ALARM1_DISABLE |
+					    ALARM2_DISABLE);
+	}
+	if (err)
+		goto exit;
+
+	/* enabled/disable irq for alarm1 */
+	if (pcf85263->interrupt_alarm == INTA) {
+		if (pcf85263_read_register
+		    (client, REGISTER_INTA_ENABLE, &value))
+			goto exit;
+		value &= ~A1IEA;
+		value |= (alarm->enabled ? A1IEA_ENABLE : A1IEA_DISABLE);
+		value &= ~ILPA;
+		value |= ILPA_PERMANENT_SIGNAL;
+		if (pcf85263_write_register
+		    (client, REGISTER_INTA_ENABLE, value))
+			goto exit;
+	} else if (pcf85263->interrupt_alarm == INTB) {
+		if (pcf85263_read_register
+		    (client, REGISTER_INTB_ENABLE, &value))
+			goto exit;
+		value &= ~A1IEB;
+		value |= (alarm->enabled ? A1IEB_ENABLE : A1IEB_DISABLE);
+		value &= ~ILPB;
+		value |= ILPB_PERMANENT_SIGNAL;
+		if (pcf85263_write_register
+		    (client, REGISTER_INTB_ENABLE, value))
+			goto exit;
+	}
+	/* clean up interrupt flag when disabling */
+	if (!alarm->enabled) {
+		if (pcf85263_read_register(client, REGISTER_FLAGS, &value))
+			goto exit;
+		value = (value & ~(ALARM1_FLAG)) | ALARM1_FLAG_CLEAR;
+		if (pcf85263_write_register(client, REGISTER_FLAGS, value))
+			goto exit;
+	}
+
+exit:
+	mutex_unlock(&pcf85263->mutex);
+	return err;
+}
+
+static int pcf85263_rtc_ioctl(struct device *dev,
+			      unsigned int cmd, unsigned long arg)
+{
+	int ret;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+	unsigned char user_value;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	switch (cmd) {
+	case RTC_WAIT_FOR_INTERRUPTS:
+		if (copy_from_user
+		    (&user_value, (unsigned char __user *)arg,
+		     sizeof(unsigned char)))
+			return -EFAULT;
+		ret = wait_event_interruptible(pcf85263->event_queue,
+					       ((user_value &
+						 pcf85263->event_interrupt)
+						== user_value));
+		if (ret)
+			return -ERESTARTSYS;
+		mutex_lock(&pcf85263->mutex);
+		pcf85263->event_interrupt &= ~user_value;
+		mutex_unlock(&pcf85263->mutex);
+		return 0;
+	case RTC_WAIT_FOR_ANY_INTERRUPT:
+		ret = wait_event_interruptible(pcf85263->event_queue,
+					       (pcf85263->event_interrupt
+						!= 0));
+		if (ret)
+			return -ERESTARTSYS;
+		mutex_lock(&pcf85263->mutex);
+		user_value = pcf85263->event_interrupt;
+		pcf85263->event_interrupt = 0;
+		mutex_unlock(&pcf85263->mutex);
+		if (copy_to_user((unsigned char __user *)arg, &user_value,
+				 sizeof(unsigned char)))
+			return -EFAULT;
+		return 0;
+	case RTC_CLEAR_INTERRUPT_FLAGS:
+		if (copy_from_user
+		    (&user_value, (unsigned char __user *)arg,
+		     sizeof(unsigned char)))
+			return -EFAULT;
+		mutex_lock(&pcf85263->mutex);
+		pcf85263->event_interrupt &= ~user_value;
+		mutex_unlock(&pcf85263->mutex);
+		return 0;
+	default:
+		return -ENOIOCTLCMD;
+	}
+}
+
+static const struct rtc_class_ops pcf85263_rtc_ops = {
+	/* RTC callbacks */
+	.set_time = pcf85263_rtc_set_time,
+	.read_time = pcf85263_rtc_read_time,
+	/* alarm callbacks */
+	.set_alarm = pcf85263_rtc_set_alarm,
+	.read_alarm = pcf85263_rtc_read_alarm,
+	.alarm_irq_enable = pcf85263_rtc_alarm_irq_enable,
+	/* custom APIs */
+	.ioctl = pcf85263_rtc_ioctl,
+};
+
+/*******************************************************************************
+ * RAM byte
+ */
+static ssize_t pcf85263_ram_byte_show(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	int err;
+	unsigned char ram_byte;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_read_register(client, REGISTER_RAM_BYTE, &ram_byte);
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	return sprintf(buf, "%hhu\n", ram_byte);
+}
+
+static ssize_t pcf85263_ram_byte_store(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t count)
+{
+	int err;
+	unsigned char ram_byte;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	err = kstrtou8(buf, 10, &ram_byte);
+	if (err)
+		return err;
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_write_register(client, REGISTER_RAM_BYTE, ram_byte);
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	return count;
+}
+
+static const struct device_attribute pcf85263_ram_byte_device_attribute = {
+	.attr.name = "ram_byte",
+	.attr.mode = S_IRUSR | S_IWUSR,
+	.show = pcf85263_ram_byte_show,
+	.store = pcf85263_ram_byte_store,
+};
+
+/*******************************************************************************
+ * REGISTERS utility
+ */
+static ssize_t pcf85263_registers_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	int err;
+	unsigned char i, data[48];
+	size_t printed_chars = 0;
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_read_registers(client, REGISTER_CENTS_OF_SECOND,
+				      data, sizeof(data));
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	err = sprintf(buf, "Reg  Val\n");
+	if (err < 0)
+		return err;
+	printed_chars += err;
+	for (i = 0; i < sizeof(data); i++) {
+		err =
+		    sprintf(&buf[printed_chars], "0x%02hhx 0x%02hhx\n", i,
+			    data[i]);
+		if (err < 0)
+			return err;
+		printed_chars += err;
+	}
+	return printed_chars;
+}
+
+static ssize_t pcf85263_registers_store(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	int err;
+	unsigned char address, value;
+	char address_string[3], value_string[3];
+	struct i2c_client *client;
+	struct pcf85263 *pcf85263;
+
+	client = to_i2c_client(dev);
+	pcf85263 = i2c_get_clientdata(client);
+#define is_hexadecimal(x)       ((x >= '0' && x <= '9') || \
+				(x >= 'a' && x <= 'f') || \
+				(x >= 'A' && x <= 'F'))
+	if (count != 10)
+		return -EINVAL;
+	if (!(buf[0] == '0' && (buf[1] == 'x' || buf[1] == 'X') &&
+	    buf[5] == '0' && (buf[6] == 'x' || buf[6] == 'X') &&
+	    is_hexadecimal(buf[2]) &&
+	    is_hexadecimal(buf[3]) &&
+	    is_hexadecimal(buf[7]) && is_hexadecimal(buf[8])))
+		return -EINVAL;
+	address_string[0] = buf[2];
+	address_string[1] = buf[3];
+	address_string[2] = '\0';
+	value_string[0] = buf[7];
+	value_string[1] = buf[8];
+	value_string[2] = '\0';
+	err = kstrtou8(address_string, 16, &address);
+	if (err)
+		return err;
+	err = kstrtou8(value_string, 16, &value);
+	if (err)
+		return err;
+	if (address > REGISTER_RESETS)
+		return -EINVAL;
+	mutex_lock(&pcf85263->mutex);
+	err = pcf85263_write_register(client, address, value);
+	mutex_unlock(&pcf85263->mutex);
+	if (err)
+		return err;
+	return count;
+}
+
+static const struct device_attribute pcf85263_registers_device_attribute = {
+	.attr.name = "registers",
+	.attr.mode = S_IRUSR | S_IWUSR,
+	.show = pcf85263_registers_show,
+	.store = pcf85263_registers_store,
+};
+
+/*******************************************************************************
+ * HW initialization
+ */
+static int pcf85263_init(struct i2c_client *client)
+{
+	int err;
+	unsigned char value;
+	struct pcf85263 *pcf85263;
+
+	pcf85263 = i2c_get_clientdata(client);
+	/*
+	 * Start the OSC if required. This operation can tamper with time.
+	 */
+	err = pcf85263_read_register(client, REGISTER_SECONDS, &value);
+	if (err)
+		return err;
+
+	// We should only write to this register if the OS bit is high otherwise we risk the
+	// SECONDS changing between the read and the write which will cause us to lose a second.
+	if (value & OS_SET) {
+		//If the OS bit is high, clear the bit to start the Oscillator
+		value &= ~OS;
+
+		err = pcf85263_write_register(client, REGISTER_SECONDS, value);
+		if (err)
+			return err;
+	}
+
+	/*
+	 * Initializing function register
+	 */
+	err = pcf85263_read_register(client, REGISTER_FUNCTION, &value);
+	if (err)
+		return err;
+	/* We don't support stop-watch mode, setting RTC mode. */
+	value &= ~RTCM;
+	value |= RTCM_RTC_MODE;
+	value &= ~COF;
+	value |= (unsigned char)pcf85263->clock_frequency;
+	err = pcf85263_write_register(client, REGISTER_FUNCTION, value);
+	if (err)
+		return err;
+
+	/*
+	 * We don't support 12 hour mode, setting 24 hour mode.
+	 */
+	err = pcf85263_read_register(client, REGISTER_OSCILLATOR, &value);
+	if (err)
+		return err;
+	value &= ~AMPM_12_24;
+	value |= AMPM_24_HOUR_MODE;
+	value &= ~XTAL_CAP_LOAD;
+	value |= XTAL_CAP_12_5_pf;	//We use a 12.5pF load capacitance
+	err = pcf85263_write_register(client, REGISTER_OSCILLATOR, value);
+	if (err)
+		return err;
+
+	/*
+	 * Initializing battery switch register
+	 */
+	err =
+	    pcf85263_read_register(client, REGISTER_BATTERY_SWITCH,
+				   &value);
+	if (err)
+		return err;
+	value &= ~BSRR;
+	value |= BSRR_LOW;
+	value &= ~BSOFF;
+	if (pcf85263->battery_switch == BATTERY_SWITCH_OFF) {
+		value |= BSOFF_DISABLE;
+	} else {
+		value |= BSOFF_ENABLE;
+		value &= ~BSM;
+		if (pcf85263->battery_switch == BATTERY_SWITCH_VTH)
+			value |= BSM_VTH;
+		else if (pcf85263->battery_switch == BATTERY_SWITCH_VBAT)
+			value |= BSM_VBAT;
+		else if (pcf85263->battery_switch == BATTERY_SWITCH_HIGHER)
+			value |= BSM_HIGHER;
+		else
+			value |= BSM_LOWER;
+		value &= ~BSTH;
+		if (pcf85263->battery_vth == BATTERY_VTH_1_5)
+			value |= BSTH_1_5;
+		else
+			value |= BSTH_2_8;
+	}
+	err = pcf85263_write_register(client, REGISTER_BATTERY_SWITCH, value);
+	if (err)
+		return err;
+
+	/*
+	 * Timestamps initialization
+	 */
+	err = pcf85263_read_register(client, REGISTER_TSR_MODE, &value);
+	if (err)
+		return err;
+	value &= ~TSR1M;
+	value |= (unsigned char)pcf85263->timestamp1_mode;
+	value &= ~TSR2M;
+	value |= (unsigned char)pcf85263->timestamp2_mode;
+	value &= ~TSR3M;
+	value |= (unsigned char)pcf85263->timestamp3_mode;
+	err = pcf85263_write_register(client, REGISTER_TSR_MODE, value);
+	if (err)
+		return err;
+
+	/*
+	 * INTA enable register initialization
+	 */
+	err = pcf85263_read_register(client, REGISTER_INTA_ENABLE, &value);
+	if (err)
+		return err;
+	if (pcf85263->watchdog_disable_on_boot) {
+		dev_info(&client->dev, "disabling watchdog interrupt\n");
+		value &= ~WDIEA;
+		value |= WDIEA_DISABLE;
+	}
+	value &= ~BSIEA;
+	if (pcf85263->interrupt_battery == INTA)
+		value |= BSIEA_ENABLE;
+	else
+		value |= BSIEA_DISABLE;
+	value &= ~TSRIEA;
+	if (pcf85263->interrupt_timestamp == INTA)
+		value |= TSRIEA_ENABLE;
+	else
+		value |= TSRIEA_DISABLE;
+	err = pcf85263_write_register(client, REGISTER_INTA_ENABLE, value);
+	if (err)
+		return err;
+
+	/*
+	 * INTB enable register initialization
+	 */
+	err = pcf85263_read_register(client, REGISTER_INTB_ENABLE, &value);
+	if (err)
+		return err;
+	if (pcf85263->watchdog_disable_on_boot) {
+		value &= ~WDIEB;
+		value |= WDIEB_DISABLE;
+	}
+	value &= ~BSIEB;
+	if (pcf85263->interrupt_battery == INTB)
+		value |= BSIEB_ENABLE;
+	else
+		value |= BSIEB_DISABLE;
+	value &= ~TSRIEB;
+	if (pcf85263->interrupt_timestamp == INTB)
+		value |= TSRIEB_ENABLE;
+	else
+		value |= TSRIEB_DISABLE;
+	err = pcf85263_write_register(client, REGISTER_INTB_ENABLE, value);
+	if (err)
+		return err;
+
+	/*
+	 * Watchdog register initialization
+	 */
+	err = pcf85263_read_register(client, REGISTER_WATCHDOG, &value);
+	if (err)
+		return err;
+	value &= ~WDM;
+	value |= WDM_SINGLE_SHOT;
+	err = pcf85263_write_register(client, REGISTER_WATCHDOG, value);
+	if (err)
+		return err;
+
+	/*
+	 * Initializing Pin I/O
+	 */
+	err = pcf85263_read_register(client, REGISTER_PIN_IO, &value);
+	if (err)
+		return err;
+	/* CLKPM */
+	value &= ~CLKPM;
+	value |= (unsigned char)pcf85263->clk_pin;
+	/* TSPULL */
+	value &= ~TSPULL;
+	value |= (unsigned char)pcf85263->ts_pin_pull;
+	/* TSL */
+	value &= ~TSL;
+	value |= (unsigned char)pcf85263->ts_pin_level;
+	/* TSIM */
+	value &= ~TSIM;
+	value |= (unsigned char)pcf85263->ts_pin_input_type;
+	/* TSPM */
+	value &= ~TSPM;
+	value |= (unsigned char)pcf85263->ts_pin;
+	/* INTAPM */
+	value &= ~INTAPM;
+	value |= (unsigned char)pcf85263->inta_pin;
+	err = pcf85263_write_register(client, REGISTER_PIN_IO, value);
+	if (err)
+		return err;
+
+// Clear interrupt flags, but leave the time stamp flags
+	err = pcf85263_write_register(client, REGISTER_FLAGS, 0x07);
+
+	return err;
+}
+
+static void pcf85263_unload(struct i2c_client *client)
+{
+	struct pcf85263 *pcf85263;
+	int err;
+
+	pcf85263 = i2c_get_clientdata(client);
+	if (pcf85263->ram_byte_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_ram_byte_device_attribute.attr);
+	}
+
+	if (pcf85263->flags_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_flags_attribute.attr);
+	}
+
+	if (pcf85263->registers_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_registers_device_attribute.attr);
+	}
+	if (pcf85263->timestamp1_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_timestamp1_attribute.attr);
+		pcf85263->timestamp1_file_created = 0;
+	}
+	if (pcf85263->timestamp2_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_timestamp2_attribute.attr);
+		pcf85263->timestamp2_file_created = 0;
+	}
+	if (pcf85263->timestamp3_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_timestamp3_attribute.attr);
+		pcf85263->timestamp3_file_created = 0;
+	}
+	if (pcf85263->resets_file_created) {
+		sysfs_remove_file(&client->dev.kobj,
+				  &pcf85263_resets_attribute.attr);
+		pcf85263->resets_file_created = 0;
+	}
+	if (wdten == 1) {
+		dev_dbg(&client->dev, "[%s] watchdog unregister\n",
+			__func__);
+		watchdog_unregister_device(&pcf85263_watchdog_device);
+	}
+	dev_dbg(&client->dev, "[%s] pinctrl sleep state\n", __func__);
+	pinctrl_pm_select_sleep_state(&client->dev);
+	dev_dbg(&client->dev, "[%s] devm_kfree\n", __func__);
+	err = device_init_wakeup(&client->dev, false);
+	if (err)
+		dev_err(&client->dev, "dev_init_wakeup [%d] FAIL\n", err);
+	devm_kfree(&client->dev, pcf85263);
+}
+
+/*
+ * Driver hooks
+ */
+static int pcf85263_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	int err;
+	struct pcf85263 *pcf85263;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
+		return -ENODEV;
+
+	pcf85263 =
+	    devm_kzalloc(&client->dev, sizeof(struct pcf85263),
+			 GFP_KERNEL);
+	if (!pcf85263) {
+		dev_dbg(&client->dev,
+			"[%s] Impossible to allocate memory\n", __func__);
+		return -ENOMEM;
+	}
+	pcf85263->ram_byte_file_created = 0;
+	pcf85263->registers_file_created = 0;
+	pcf85263->timestamp1_file_created = 0;
+	pcf85263->timestamp2_file_created = 0;
+	pcf85263->timestamp3_file_created = 0;
+	pcf85263->resets_file_created = 0;
+	pcf85263->inta_irq = -1;
+	pcf85263->intb_irq = -1;
+	pcf85263->battery_switch = BATTERY_SWITCH_OFF;
+	pcf85263->battery_vth = BATTERY_VTH_1_5;
+	init_waitqueue_head(&pcf85263->event_queue);
+	if (timeout < 1 || timeout > 124) {
+		dev_dbg(&client->dev,
+			"[%s] timeout (= %d) out of bounds ([1,124])\n",
+			__func__, timeout);
+		timeout = WATCHDOG_TIMEOUT;
+	}
+	pcf85263->watchdog_timeout = timeout;
+	mutex_init(&pcf85263->mutex);
+
+	dev_info(&client->dev,
+		 "chip found, driver version " DRIVER_VERSION "\n");
+
+	i2c_set_clientdata(client, pcf85263);
+	pcf85263->client = client;
+	pcf85263->rtc = devm_rtc_device_register(&client->dev,
+						 pcf85263_driver.driver.name,
+						 &pcf85263_rtc_ops,
+						 THIS_MODULE);
+	err = PTR_ERR_OR_ZERO(pcf85263->rtc);
+	if (err) {
+		dev_err(&client->dev, "unable to register RTC device\n");
+		goto exit;
+	}
+
+	pcf85263->rtc->uie_unsupported = 1;
+	/* RAM byte initialization */
+	err = sysfs_create_file(&client->dev.kobj,
+				&pcf85263_ram_byte_device_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_ram_byte_device_attribute.attr.name);
+		goto exit;
+	}
+	pcf85263->ram_byte_file_created = 1;
+
+	/* Registers debug initialization */
+	err = sysfs_create_file(&client->dev.kobj,
+				&pcf85263_registers_device_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_registers_device_attribute.attr.name);
+		goto exit;
+	}
+	pcf85263->registers_file_created = 1;
+
+	/* flags initialization */
+	err =
+	    sysfs_create_file(&client->dev.kobj,
+			      &pcf85263_flags_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_flags_attribute.attr.name);
+		goto exit;
+	}
+	pcf85263->flags_file_created = 1;
+
+	/* Timestamp 1 initialization */
+	err = sysfs_create_file(&client->dev.kobj,
+				&pcf85263_timestamp1_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_timestamp1_attribute.attr.name);
+		goto exit;
+	}
+	pcf85263->timestamp1_file_created = 1;
+
+	/* Timestamp 2 initialization */
+	err = sysfs_create_file(&client->dev.kobj,
+				&pcf85263_timestamp2_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_timestamp2_attribute.attr.name);
+		goto exit;
+	}
+	pcf85263->timestamp2_file_created = 1;
+
+	/* Timestamp 3 initialization */
+	err = sysfs_create_file(&client->dev.kobj,
+				&pcf85263_timestamp3_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_timestamp3_attribute.attr.name);
+		goto exit;
+	}
+	pcf85263->timestamp3_file_created = 1;
+
+	/* Create resets file */
+	err = sysfs_create_file(&client->dev.kobj,
+				&pcf85263_resets_attribute.attr);
+	if (err) {
+		dev_err(&client->dev,
+			"unable to create sysfs file \"%s\"\n",
+			pcf85263_resets_attribute.attr.name);
+	}
+	pcf85263->resets_file_created = 1;
+
+	/* Battery switch specific device tree properties */
+	pcf85263->battery_switch = BATTERY_SWITCH_VTH;
+	if (vth == 0)
+		pcf85263->battery_vth = BATTERY_VTH_1_5;
+	else
+		pcf85263->battery_vth = BATTERY_VTH_2_8;
+	/* Battery switch interrupt initialization */
+
+	pcf85263->interrupt_battery = INTA;
+	if (strcmp(int_batt, "INTA"))
+		pcf85263->interrupt_battery = INTA;
+	else if (strcmp(int_batt, "INTB"))
+		pcf85263->interrupt_battery = INTB;
+	else if (strcmp(int_batt, "NO_INTERRUPT"))
+		pcf85263->interrupt_battery = NO_INTERRUPT;
+
+	/* Timestamps specific device tree properties setup */
+	pcf85263->timestamp1_mode = TSR1M_LAST_TS_EVENT;
+	pcf85263->timestamp2_mode = TSR2M_LAST_SWITCH_TO_BATTERY;
+	pcf85263->timestamp3_mode = TSR3M_LAST_SWITCH_TO_VDD;
+	pcf85263->interrupt_timestamp = INTB;
+	if (strcmp(int_tst, "INTA"))
+		pcf85263->interrupt_timestamp = INTA;
+	else if (strcmp(int_tst, "INTB"))
+		pcf85263->interrupt_timestamp = INTB;
+	else if (strcmp(int_tst, "NO_INTERRUPT"))
+		pcf85263->interrupt_timestamp = NO_INTERRUPT;
+
+	pcf85263->interrupt_watchdog = NO_INTERRUPT;
+	if (strcmp(int_wdt, "INTA"))
+		pcf85263->interrupt_watchdog = INTA;
+	else if (strcmp(int_wdt, "INTB"))
+		pcf85263->interrupt_watchdog = INTB;
+	else if (strcmp(int_wdt, "NO_INTERRUPT"))
+		pcf85263->interrupt_watchdog = NO_INTERRUPT;
+
+	/* INTA pin configuration */
+
+	pcf85263->inta_pin = INTAPM_INTA;
+	if (strcmp(intapm_conf, "INTAPM_CLK_OUTPUT"))
+		pcf85263->inta_pin = INTA;
+	else if (strcmp(intapm_conf, "INTAPM_BATTERY_MODE_INDICATION"))
+		pcf85263->inta_pin = INTB;
+	else if (strcmp(intapm_conf, "INTAPM_INTA"))
+		pcf85263->inta_pin = INTAPM_INTA;
+	else if (strcmp(intapm_conf, "INTAPM_HIGH_IMPEDANCE"))
+		pcf85263->inta_pin = INTAPM_HIGH_IMPEDANCE;
+
+	pcf85263->ts_pin = TSPM_DISABLED;
+	if (strcmp(tspm, "TSPM_DISABLED") == 0)
+		pcf85263->ts_pin = TSPM_DISABLED;
+	else if (strcmp(tspm, "TSPM_INT") == 0)
+		pcf85263->ts_pin = TSPM_INTB;
+	else if (strcmp(tspm, "TSPM_CLK_OUTPUT") == 0)
+		pcf85263->ts_pin = TSPM_CLK_OUTPUT;
+	else if (strcmp(tspm, "TSPM_INPUT_MODE") == 0)
+		pcf85263->ts_pin = TSPM_INPUT_MODE;
+
+	pcf85263->clock_frequency = COF_32768;
+	pcf85263->clk_pin = CLKPM_ENABLE;
+
+	/* TS pin configuration */
+	pcf85263->ts_pin_pull = TSPULL_80_K_OHM;
+
+	if (tsl == 0)
+		pcf85263->ts_pin_level = TSL_ACTIVE_LOW;
+	else
+		pcf85263->ts_pin_level = TSL_ACTIVE_HIGH;
+
+	pcf85263->ts_pin_input_type = TSIM_MECHANICAL_SWITCH_MODE;
+	/* Watchdog specific device tree properties setup */
+	pcf85263->watchdog_disable_on_boot = 0;
+	/* Init the chip with the desired configuration */
+	err = pcf85263_init(client);
+	if (err) {
+		dev_err(&client->dev, "unable to init RTC device\n");
+		goto exit;
+	}
+
+	if (pinctrl_pm_select_default_state(&client->dev))
+		goto exit;
+
+	if (wakeen == 1) {
+		err = device_init_wakeup(&client->dev, true);
+		if (err)
+			dev_err(&client->dev,
+				"dev_init_wakeup [%d] FAIL\n", err);
+	}
+
+	if (wdten == 1) {
+		watchdog_set_drvdata(&pcf85263_watchdog_device, client);
+		watchdog_init_timeout(&pcf85263_watchdog_device,
+				      pcf85263->watchdog_timeout, NULL);
+		watchdog_set_nowayout(&pcf85263_watchdog_device, nowayout);
+		err = watchdog_register_device(&pcf85263_watchdog_device);
+		if (err)
+			goto exit;
+		dev_info(&client->dev, "registered %s as watchdog%d\n",
+			 pcf85263_driver.driver.name,
+			 pcf85263_watchdog_device.id);
+	}
+	dev_info(&client->dev, "probe_end, init OK\n");
+	return 0;
+exit:
+	pcf85263_unload(client);
+	return err;
+}
+
+static int pcf85263_remove(struct i2c_client *client)
+{
+	pcf85263_unload(client);
+	return 0;
+}
+
+static const struct i2c_device_id pcf85263_id[] = {
+	{"pcf85263", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, pcf85263_id);
+
+static struct of_device_id pcf85263_of_match[] = {
+	{.compatible = "nxp,pcf85263"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, pcf85263_of_match);
+
+#ifdef CONFIG_PM_SLEEP
+static int pcf85263_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct pcf85263 *pcf85263;
+
+	pcf85263 = i2c_get_clientdata(client);
+
+	if (pcf85263->inta_irq >= 0 && device_may_wakeup(&client->dev))
+		enable_irq_wake(pcf85263->inta_irq);
+
+	return 0;
+}
+
+static int pcf85263_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct pcf85263 *pcf85263;
+	void __iomem *reg0 = ioremap(GPIO0_IRQSTATUS_0_ADDR, 4);
+	void __iomem *reg1 = ioremap(GPIO0_IRQSTATUS_1_ADDR, 4);
+
+	pcf85263 = i2c_get_clientdata(client);
+
+	if (pcf85263->inta_irq >= 0 && device_may_wakeup(&client->dev)) {
+		disable_irq_wake(pcf85263->inta_irq);
+		writel(GPIO0_19_SET_BIT_ACK, reg0);
+		writel(GPIO0_19_SET_BIT_ACK, reg1);
+	}
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(pcf85263_pm, pcf85263_suspend, pcf85263_resume);
+
+static struct i2c_driver pcf85263_driver = {
+	.driver = {
+		   .name = "rtc-pcf85263",
+		   .owner = THIS_MODULE,
+		   .pm = &pcf85263_pm,
+		   .of_match_table = of_match_ptr(pcf85263_of_match),
+		   },
+	.probe = pcf85263_probe,
+	.remove = pcf85263_remove,
+	.id_table = pcf85263_id,
+};
+
+module_i2c_driver(pcf85263_driver);
+
+MODULE_AUTHOR("Fabrizio Castro <fabrizio.castro@eurotech.com>");
+MODULE_DESCRIPTION("NXP PCF85263 driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRIVER_VERSION);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pcf85263.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pcf85263.h
@@ -0,0 +1,387 @@
+/* SPDX-License-Identifier: GPL-2.0
+ * NXP PCF85263 RTC driver
+ * Copyright (C) 2015 Eurotech Ltd Fabrizio Castro
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; If not, see <http://www.gnu.org/licenses/>
+ */
+
+#ifndef __RTC_PCF85263_H__
+#define __RTC_PCF85263_H__
+
+#define DRIVER_VERSION "0.1"
+
+#define BIT0 0x01
+#define BIT1 0x02
+#define BIT2 0x04
+#define BIT3 0x08
+#define BIT4 0x10
+#define BIT5 0x20
+#define BIT6 0x40
+#define BIT7 0x80
+
+/*
+ * RTC mode time registers
+ * RTCM = 0
+ */
+
+// RTC time and date registers
+#define REGISTER_CENTS_OF_SECOND 0x00
+#define CENTS_OF_SECONDS_BITS 0xFF
+
+#define REGISTER_SECONDS 0x01
+#define SECONDS_BITS 0x7F
+#define OS BIT7
+#define OS_SET BIT7
+#define OS_CLEAR 0x00
+
+#define REGISTER_MINUTES 0x02
+#define MINUTES_BITS 0x7F
+#define EMON BIT7
+
+#define REGISTER_HOURS 0x03
+#define HOURS_BITS 0x3F
+
+#define REGISTER_DAYS 0x04
+#define DAYS_BITS 0x3F
+
+#define REGISTER_WEEKDAYS 0x05
+#define WEEKDAYS_BITS 0x03
+
+#define REGISTER_MONTHS 0x06
+#define MONTHS_BITS 0x1F
+
+#define REGISTER_YEARS 0x07
+#define YEARS_BITS 0xFF
+
+// RTC alarm1
+#define REGISTER_SECOND_ALARM1 0x08
+
+#define REGISTER_MINUTE_ALARM1 0x09
+
+#define REGISTER_HOUR_ALARM1 0x0A
+
+#define REGISTER_DAY_ALARM1 0x0B
+
+#define REGISTER_MONTH_ALARM1 0x0C
+
+// RTC alarm2
+#define REGISTER_MINUTE_ALARM2 0x0D
+
+#define REGISTER_HOUR_ALARM2 0x0E
+
+#define REGISTER_WEEKDAY_ALARM2 0x0F
+
+// RTC alarm enables
+#define REGISTER_ALARM_ENABLES 0x10
+#define WDAY_A2E BIT7
+#define WDAY_A2E_ENABLE BIT7
+#define WDAY_A2E_DISABLE 0x00
+#define HR_A2E BIT6
+#define HR_A2E_ENABLE BIT6
+#define HR_A2E_DISABLE 0x00
+#define MIN_A2E BIT5
+#define MIN_A2E_ENABLE BIT5
+#define MIN_A2E_DISABLE 0x00
+#define MON_A1E BIT4
+#define MON_A1E_ENABLE BIT4
+#define MON_A1E_DISABLE 0x00
+#define DAY_A1E BIT3
+#define DAY_A1E_ENABLE BIT3
+#define DAY_A1E_DISABLE 0x00
+#define HR_A1E BIT2
+#define HR_A1E_ENABLE BIT2
+#define HR_A1E_DISABLE 0x00
+#define MIN_A1E BIT1
+#define MIN_A1E_ENABLE BIT1
+#define MIN_A1E_DISABLE 0x00
+#define SEC_A1E BIT0
+#define SEC_A1E_ENABLE BIT0
+#define SEC_A1E_DISABLE 0x00
+#define ALARM1_BITS (MON_A1E | \
+	DAY_A1E | \
+	HR_A1E | \
+	MIN_A1E | \
+	SEC_A1E)
+#define ALARM1_ENABLE (MON_A1E_ENABLE | \
+	DAY_A1E_ENABLE | \
+	HR_A1E_ENABLE | \
+	MIN_A1E_ENABLE | \
+	SEC_A1E_ENABLE)
+#define ALARM1_DISABLE (MON_A1E_DISABLE | \
+	DAY_A1E_DISABLE | \
+	HR_A1E_DISABLE | \
+	MIN_A1E_DISABLE | \
+	SEC_A1E_DISABLE)
+#define ALARM2_ENABLE (WDAY_A2E_ENABLE | \
+	HR_A2E_ENABLE | \
+	MIN_A2E_ENABLE)
+#define ALARM2_DISABLE (WDAY_A2E_DISABLE | \
+	HR_A2E_DISABLE | \
+	MIN_A2E_DISABLE)
+
+// RTC timestamp1 (TSR1)
+#define REGISTER_TSR1_SECONDS 0x11
+
+#define REGISTER_TSR1_MINUTES 0x12
+
+#define REGISTER_TSR1_HOURS 0x13
+
+#define REGISTER_TSR1_DAYS 0x14
+
+#define REGISTER_TSR1_MONTHS 0x15
+
+#define REGISTER_TSR1_YEARS 0x16
+
+// RTC timestamp2 (TSR2)
+#define REGISTER_TSR2_SECONDS 0x17
+
+#define REGISTER_TSR2_MINUTES 0x18
+
+#define REGISTER_TSR2_HOURS 0x19
+
+#define REGISTER_TSR2_DAYS 0x1A
+
+#define REGISTER_TSR2_MONTHS 0x1B
+
+#define REGISTER_TSR2_YEARS 0x1C
+
+// RTC timestamp3 (TSR3)
+#define REGISTER_TSR3_SECONDS 0x1D
+
+#define REGISTER_TSR3_MINUTES 0x1E
+
+#define REGISTER_TSR3_HOURS 0x1F
+
+#define REGISTER_TSR3_DAYS 0x20
+
+#define REGISTER_TSR3_MONTHS 0x21
+
+#define REGISTER_TSR3_YEARS 0x22
+
+// RTC timestamp mode control
+#define REGISTER_TSR_MODE 0x23
+#define TSR1M (BIT1 | BIT0)
+#define TSR1M_NO_TIMESTAMP 0x00
+#define TSR1M_FIRST_TS_EVENT BIT0
+#define TSR1M_LAST_TS_EVENT BIT1
+#define TSR2M (BIT4 | BIT3 | BIT2)
+#define TSR2M_NO_TIMESTAMP 0x00
+#define TSR2M_FIRST_SWITCH_TO_BATTERY BIT2
+#define TSR2M_LAST_SWITCH_TO_BATTERY BIT3
+#define TSR2M_LAST_SWITCH_TO_VDD (BIT3 | BIT2)
+#define TSR2M_FIRST_TS_EVENT BIT4
+#define TSR2M_LAST_TS_EVENT (BIT4 | BIT2)
+#define TSR3M (BIT7 | BIT6)
+#define TSR3M_NO_TIMESTAMP 0x00
+#define TSR3M_FIRST_SWITCH_TO_BATTERY BIT6
+#define TSR3M_LAST_SWITCH_TO_BATTERY BIT7
+#define TSR3M_LAST_SWITCH_TO_VDD (BIT7 | BIT6)
+
+/*
+ * Control and function registers overview
+ */
+
+// Offset register
+#define REGISTER_OFFSET 0x24
+
+// Control registers
+#define REGISTER_OSCILLATOR 0x25
+#define AMPM_12_24 BIT5
+#define AMPM_12_HOUR_MODE BIT5
+#define AMPM_24_HOUR_MODE 0x00
+#define XTAL_CAP_LOAD 0x03	//BIT0 & BIT1
+#define XTAL_CAP_7_0pf 0x00
+#define XTAL_CAP_6_0pf 0x01
+#define XTAL_CAP_12_5pf 0x02
+#define XTAL_CAP_12_5_pf 0x03	//Datasheet says 12.5pF for both 0x02 & 0x03
+
+#define REGISTER_BATTERY_SWITCH 0x26
+#define BSOFF BIT4
+#define BSOFF_ENABLE 0X00
+#define BSOFF_DISABLE BIT4
+#define BSRR BIT3
+#define BSRR_LOW 0x00
+#define BSRR_HIGH BIT3
+#define BSM (BIT2 | BIT1)
+#define BSM_VTH 0X00
+#define BSM_VBAT BIT1
+#define BSM_HIGHER BIT2
+#define BSM_LOWER (BIT2 | BIT1)
+#define BSTH BIT0
+#define BSTH_1_5 0x00
+#define BSTH_2_8 BIT0
+
+#define BATTERY_SWITCH_OFF 0
+#define BATTERY_SWITCH_VTH 1
+#define BATTERY_SWITCH_VBAT 2
+#define BATTERY_SWITCH_HIGHER 3
+#define BATTERY_SWITCH_LOWER 4
+
+#define BATTERY_VTH_1_5 0
+#define BATTERY_VTH_2_8 1
+
+#define REGISTER_PIN_IO 0x27
+#define CLKPM BIT7
+#define CLKPM_ENABLE 0x00
+#define CLKPM_DISABLE BIT7
+#define TSPULL BIT6
+#define TSPULL_80_K_OHM 0x00
+#define TSPULL_40_K_OHM BIT6
+#define TSL BIT5
+#define TSL_ACTIVE_HIGH 0x00
+#define TSL_ACTIVE_LOW BIT5
+#define TSIM BIT4
+#define TSIM_CMOS_INPUT 0x00
+#define TSIM_MECHANICAL_SWITCH_MODE BIT4
+#define TSPM (BIT3 | BIT2)
+#define TSPM_DISABLED 0x00
+#define TSPM_INTB BIT2
+#define TSPM_CLK_OUTPUT BIT3
+#define TSPM_INPUT_MODE (BIT3 | BIT2)
+#define INTAPM (BIT1 | BIT0)
+#define INTAPM_CLK_OUTPUT 0x00
+#define INTAPM_BATTERY_MODE_INDICATION BIT0
+#define INTAPM_INTA BIT1
+#define INTAPM_HIGH_IMPEDANCE (BIT1 | BIT0)
+
+#define REGISTER_FUNCTION 0x28
+#define RTCM BIT4
+#define RTCM_RTC_MODE 0x00
+#define RTCM_STOP_WATCH_MODE BIT4
+#define COF (BIT2 | BIT1 | BIT0)
+#define COF_32768 0x00
+#define COF_16384 BIT0
+#define COF_8192 BIT1
+#define COF_4096 (BIT1 | BIT0)
+#define COF_2048 BIT2
+#define COF_1024 (BIT2 | BIT0)
+#define COF_1 (BIT2 | BIT1)
+#define COF_LOW (BIT2 | BIT1 | BIT0)
+
+#define REGISTER_INTA_ENABLE 0x29
+#define ILPA BIT7
+#define ILPA_PULSE_SIGNAL 0x00
+#define ILPA_PERMANENT_SIGNAL BIT7
+#define PIEA BIT6
+#define PIEA_ENABLE BIT6
+#define PIEA_DISABLE 0x00
+#define OIEA BIT5
+#define OIEA_ENABLE BIT5
+#define OIEA_DISABLE 0x00
+#define A1IEA BIT4
+#define A1IEA_ENABLE BIT4
+#define A1IEA_DISABLE 0x00
+#define A2IEA BIT3
+#define A2IEA_ENABLE BIT3
+#define A2IEA_DISABLE 0x00
+#define TSRIEA BIT2
+#define TSRIEA_ENABLE BIT2
+#define TSRIEA_DISABLE 0x00
+#define BSIEA BIT1
+#define BSIEA_ENABLE BIT1
+#define BSIEA_DISABLE 0x00
+#define WDIEA BIT0
+#define WDIEA_ENABLE BIT0
+#define WDIEA_DISABLE 0x00
+
+#define REGISTER_INTB_ENABLE 0x2A
+#define ILPB BIT7
+#define ILPB_PULSE_SIGNAL 0x00
+#define ILPB_PERMANENT_SIGNAL BIT7
+#define PIEB BIT6
+#define PIEB_ENABLE BIT6
+#define PIEB_DISABLE 0x00
+#define OIEB BIT5
+#define OIEB_ENABLE BIT5
+#define OIEB_DISABLE 0x00
+#define A1IEB BIT4
+#define A1IEB_ENABLE BIT4
+#define A1IEB_DISABLE 0x00
+#define A2IEB BIT3
+#define A2IEB_ENABLE BIT3
+#define A2IEB_DISABLE 0x00
+#define TSRIEB BIT2
+#define TSRIEB_ENABLE BIT2
+#define TSRIEB_DISABLE 0x00
+#define BSIEB BIT1
+#define BSIEB_ENABLE BIT1
+#define BSIEB_DISABLE 0x00
+#define WDIEB BIT0
+#define WDIEB_ENABLE BIT0
+#define WDIEB_DISABLE 0x00
+
+#define REGISTER_FLAGS 0x2B
+#define PERIODIC_INTERRUPT_FLAG BIT7
+#define PERIODIC_INTERRUPT_FLAG_ACTIVE BIT7
+#define PERIODIC_INTERRUPT_FLAG_CLEAR 0x00
+#define ALARM2_FLAG BIT6
+#define ALARM2_FLAG_ACTIVE BIT6
+#define ALARM2_FLAG_CLEAR 0x00
+#define ALARM1_FLAG BIT5
+#define ALARM1_FLAG_ACTIVE BIT5
+#define ALARM1_FLAG_CLEAR 0x00
+#define WATCHDOG_FLAG BIT4
+#define WATCHDOG_FLAG_ACTIVE BIT4
+#define WATCHDOG_FLAG_CLEAR 0x00
+#define BATTERY_SWITCH_FLAG BIT3
+#define BATTERY_SWITCH_FLAG_ACTIVE BIT3
+#define BATTERY_SWITCH_FLAG_CLEAR 0x00
+#define TIMESTAMP_3_FLAG BIT2
+#define TIMESTAMP_3_FLAG_ACTIVE BIT2
+#define TIMESTAMP_3_FLAG_CLEAR 0x00
+#define TIMESTAMP_2_FLAG BIT1
+#define TIMESTAMP_2_FLAG_ACTIVE BIT1
+#define TIMESTAMP_2_FLAG_CLEAR 0x00
+#define TIMESTAMP_1_FLAG BIT0
+#define TIMESTAMP_1_FLAG_ACTIVE BIT0
+#define TIMESTAMP_1_FLAG_CLEAR 0x00
+
+// RAM byte
+#define REGISTER_RAM_BYTE 0x2C
+
+// WatchDog registers
+#define REGISTER_WATCHDOG 0x2D
+#define WDM BIT7
+#define WDM_SINGLE_SHOT 0x00
+#define WDM_REPEAT_MODE BIT7
+#define WDR (BIT6 | BIT5 | BIT4 | BIT3 | BIT2)
+#define WDS (BIT1 | BIT0)
+#define WDS_4_SECONDS 0x00
+#define WDS_1_SECOND BIT0
+#define WDS_1_OVER_4_SECOND BIT1
+#define WDS_1_OVER_16_SECOND (BIT1 | BIT0)
+
+// Stop
+#define REGISTER_STOP_ENABLE 0x2E
+#define STOP BIT0
+#define STOP_RTC_RUN 0x00
+#define STOP_RTC_STOPPED BIT0
+
+// Reset
+#define REGISTER_RESETS 0x2F
+#define SR_CMD 0x2C	/* Software Reset, it also triggers CPR and CTS */
+#define CPR_CMD 0xA4	/* Clear PRescaler */
+#define CTS_CMD 0x25	/* Clear TimeStamps */
+#define CPR_CTS_CMD 0xA5	/* Combines CPR and CTS commands */
+
+#define ALARM_ENABLED 1
+#define ALARM_DISABLED 0
+#define ALARM_PENDING 1
+#define ALARM_NOT_PENDING 0
+
+#define NO_INTERRUPT -1
+#define INTA 0
+#define INTB 1
+
+#endif				/* __RTC_PCF85263_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pcf85363.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pcf85363.c
@@ -403,7 +403,7 @@
 	if (client->irq > 0) {
 		regmap_write(pcf85363->regmap, CTRL_FLAGS, 0);
 		regmap_update_bits(pcf85363->regmap, CTRL_PIN_IO,
-				   PIN_IO_INTA_OUT, PIN_IO_INTAPM);
+				   PIN_IO_INTAPM, PIN_IO_INTA_OUT);
 		ret = devm_request_threaded_irq(&client->dev, client->irq,
 						NULL, pcf85363_rtc_handle_irq,
 						IRQF_TRIGGER_LOW | IRQF_ONESHOT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pic32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pic32.c
@@ -324,16 +324,16 @@
 
 	spin_lock_init(&pdata->alarm_lock);
 
+	pdata->rtc = devm_rtc_allocate_device(&pdev->dev);
+	if (IS_ERR(pdata->rtc))
+		return PTR_ERR(pdata->rtc);
+
 	clk_prepare_enable(pdata->clk);
 
 	pic32_rtc_enable(pdata, 1);
 
 	device_init_wakeup(&pdev->dev, 1);
 
-	pdata->rtc = devm_rtc_allocate_device(&pdev->dev);
-	if (IS_ERR(pdata->rtc))
-		return PTR_ERR(pdata->rtc);
-
 	pdata->rtc->ops = &pic32_rtcops;
 	pdata->rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
 	pdata->rtc->range_max = RTC_TIMESTAMP_END_2099;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pl031.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pl031.c
@@ -350,9 +350,6 @@
 		}
 	}
 
-	if (!adev->irq[0])
-		clear_bit(RTC_FEATURE_ALARM, ldata->rtc->features);
-
 	device_init_wakeup(&adev->dev, true);
 	ldata->rtc = devm_rtc_allocate_device(&adev->dev);
 	if (IS_ERR(ldata->rtc)) {
@@ -360,6 +357,9 @@
 		goto out;
 	}
 
+	if (!adev->irq[0])
+		clear_bit(RTC_FEATURE_ALARM, ldata->rtc->features);
+
 	ldata->rtc->ops = ops;
 	ldata->rtc->range_min = vendor->range_min;
 	ldata->rtc->range_max = vendor->range_max;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pm8xxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pm8xxx.c
@@ -220,7 +220,6 @@
 {
 	int rc, i;
 	u8 value[NUM_8_BIT_RTC_REGS];
-	unsigned int ctrl_reg;
 	unsigned long secs, irq_flags;
 	struct pm8xxx_rtc *rtc_dd = dev_get_drvdata(dev);
 	const struct pm8xxx_rtc_regs *regs = rtc_dd->regs;
@@ -232,6 +231,11 @@
 		secs >>= 8;
 	}
 
+	rc = regmap_update_bits(rtc_dd->regmap, regs->alarm_ctrl,
+				regs->alarm_en, 0);
+	if (rc)
+		return rc;
+
 	spin_lock_irqsave(&rtc_dd->ctrl_reg_lock, irq_flags);
 
 	rc = regmap_bulk_write(rtc_dd->regmap, regs->alarm_rw, value,
@@ -241,19 +245,11 @@
 		goto rtc_rw_fail;
 	}
 
-	rc = regmap_read(rtc_dd->regmap, regs->alarm_ctrl, &ctrl_reg);
-	if (rc)
-		goto rtc_rw_fail;
-
-	if (alarm->enabled)
-		ctrl_reg |= regs->alarm_en;
-	else
-		ctrl_reg &= ~regs->alarm_en;
-
-	rc = regmap_write(rtc_dd->regmap, regs->alarm_ctrl, ctrl_reg);
-	if (rc) {
-		dev_err(dev, "Write to RTC alarm control register failed\n");
-		goto rtc_rw_fail;
+	if (alarm->enabled) {
+		rc = regmap_update_bits(rtc_dd->regmap, regs->alarm_ctrl,
+					regs->alarm_en, regs->alarm_en);
+		if (rc)
+			goto rtc_rw_fail;
 	}
 
 	dev_dbg(dev, "Alarm Set for h:m:s=%ptRt, y-m-d=%ptRdr\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-pxa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-pxa.c
@@ -330,6 +330,10 @@
 	if (sa1100_rtc->irq_alarm < 0)
 		return -ENXIO;
 
+	sa1100_rtc->rtc = devm_rtc_allocate_device(&pdev->dev);
+	if (IS_ERR(sa1100_rtc->rtc))
+		return PTR_ERR(sa1100_rtc->rtc);
+
 	pxa_rtc->base = devm_ioremap(dev, pxa_rtc->ress->start,
 				resource_size(pxa_rtc->ress));
 	if (!pxa_rtc->base) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-rv3032.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-rv3032.c
@@ -617,11 +617,11 @@
 
 	ret = rv3032_enter_eerd(rv3032, &eerd);
 	if (ret)
-		goto exit_eerd;
+		return ret;
 
 	ret = regmap_write(rv3032->regmap, RV3032_CLKOUT1, hfd & 0xff);
 	if (ret)
-		return ret;
+		goto exit_eerd;
 
 	ret = regmap_write(rv3032->regmap, RV3032_CLKOUT2, RV3032_CLKOUT2_OS |
 			    FIELD_PREP(RV3032_CLKOUT2_HFD_MSK, hfd >> 8));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-rx8025.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-rx8025.c
@@ -55,6 +55,8 @@
 #define RX8025_BIT_CTRL2_XST	BIT(5)
 #define RX8025_BIT_CTRL2_VDET	BIT(6)
 
+#define RX8035_BIT_HOUR_1224	BIT(7)
+
 /* Clock precision adjustment */
 #define RX8025_ADJ_RESOLUTION	3050 /* in ppb */
 #define RX8025_ADJ_DATA_MAX	62
@@ -78,6 +80,7 @@
 	struct rtc_device *rtc;
 	enum rx_model model;
 	u8 ctrl1;
+	int is_24;
 };
 
 static s32 rx8025_read_reg(const struct i2c_client *client, u8 number)
@@ -226,7 +229,7 @@
 
 	dt->tm_sec = bcd2bin(date[RX8025_REG_SEC] & 0x7f);
 	dt->tm_min = bcd2bin(date[RX8025_REG_MIN] & 0x7f);
-	if (rx8025->ctrl1 & RX8025_BIT_CTRL1_1224)
+	if (rx8025->is_24)
 		dt->tm_hour = bcd2bin(date[RX8025_REG_HOUR] & 0x3f);
 	else
 		dt->tm_hour = bcd2bin(date[RX8025_REG_HOUR] & 0x1f) % 12
@@ -257,7 +260,7 @@
 	 */
 	date[RX8025_REG_SEC] = bin2bcd(dt->tm_sec);
 	date[RX8025_REG_MIN] = bin2bcd(dt->tm_min);
-	if (rx8025->ctrl1 & RX8025_BIT_CTRL1_1224)
+	if (rx8025->is_24)
 		date[RX8025_REG_HOUR] = bin2bcd(dt->tm_hour);
 	else
 		date[RX8025_REG_HOUR] = (dt->tm_hour >= 12 ? 0x20 : 0)
@@ -282,6 +285,7 @@
 	struct rx8025_data *rx8025 = i2c_get_clientdata(client);
 	u8 ctrl[2], ctrl2;
 	int need_clear = 0;
+	int hour_reg;
 	int err;
 
 	err = rx8025_read_regs(client, RX8025_REG_CTRL1, 2, ctrl);
@@ -306,6 +310,16 @@
 
 		err = rx8025_write_reg(client, RX8025_REG_CTRL2, ctrl2);
 	}
+
+	if (rx8025->model == model_rx_8035) {
+		/* In RX-8035, 12/24 flag is in the hour register */
+		hour_reg = rx8025_read_reg(client, RX8025_REG_HOUR);
+		if (hour_reg < 0)
+			return hour_reg;
+		rx8025->is_24 = (hour_reg & RX8035_BIT_HOUR_1224);
+	} else {
+		rx8025->is_24 = (ctrl[1] & RX8025_BIT_CTRL1_1224);
+	}
 out:
 	return err;
 }
@@ -335,7 +349,7 @@
 	/* Hardware alarms precision is 1 minute! */
 	t->time.tm_sec = 0;
 	t->time.tm_min = bcd2bin(ald[0] & 0x7f);
-	if (rx8025->ctrl1 & RX8025_BIT_CTRL1_1224)
+	if (rx8025->is_24)
 		t->time.tm_hour = bcd2bin(ald[1] & 0x3f);
 	else
 		t->time.tm_hour = bcd2bin(ald[1] & 0x1f) % 12
@@ -370,7 +384,7 @@
 	}
 
 	ald[0] = bin2bcd(t->time.tm_min);
-	if (rx8025->ctrl1 & RX8025_BIT_CTRL1_1224)
+	if (rx8025->is_24)
 		ald[1] = bin2bcd(t->time.tm_hour);
 	else
 		ald[1] = (t->time.tm_hour >= 12 ? 0x20 : 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-snvs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-snvs.c
@@ -32,6 +32,14 @@
 #define SNVS_LPPGDR_INIT	0x41736166
 #define CNTR_TO_SECS_SH		15
 
+/* The maximum RTC clock cycles that are allowed to pass between two
+ * consecutive clock counter register reads. If the values are corrupted a
+ * bigger difference is expected. The RTC frequency is 32kHz. With 320 cycles
+ * we end at 10ms which should be enough for most cases. If it once takes
+ * longer than expected we do a retry.
+ */
+#define MAX_RTC_READ_DIFF_CYCLES	320
+
 struct snvs_rtc_data {
 	struct rtc_device *rtc;
 	struct regmap *regmap;
@@ -56,6 +64,7 @@
 static u32 rtc_read_lp_counter(struct snvs_rtc_data *data)
 {
 	u64 read1, read2;
+	s64 diff;
 	unsigned int timeout = 100;
 
 	/* As expected, the registers might update between the read of the LSB
@@ -66,7 +75,8 @@
 	do {
 		read2 = read1;
 		read1 = rtc_read_lpsrt(data);
-	} while (read1 != read2 && --timeout);
+		diff = read1 - read2;
+	} while (((diff < 0) || (diff > MAX_RTC_READ_DIFF_CYCLES)) && --timeout);
 	if (!timeout)
 		dev_err(&data->rtc->dev, "Timeout trying to get valid LPSRT Counter read\n");
 
@@ -78,13 +88,15 @@
 static int rtc_read_lp_counter_lsb(struct snvs_rtc_data *data, u32 *lsb)
 {
 	u32 count1, count2;
+	s32 diff;
 	unsigned int timeout = 100;
 
 	regmap_read(data->regmap, data->offset + SNVS_LPSRTCLR, &count1);
 	do {
 		count2 = count1;
 		regmap_read(data->regmap, data->offset + SNVS_LPSRTCLR, &count1);
-	} while (count1 != count2 && --timeout);
+		diff = count1 - count2;
+	} while (((diff < 0) || (diff > MAX_RTC_READ_DIFF_CYCLES)) && --timeout);
 	if (!timeout) {
 		dev_err(&data->rtc->dev, "Timeout trying to get valid LPSRT Counter read\n");
 		return -ETIMEDOUT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-st-lpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-st-lpc.c
@@ -218,17 +218,16 @@
 		return -EINVAL;
 	}
 
-	ret = devm_request_irq(&pdev->dev, rtc->irq, st_rtc_handler, 0,
-			       pdev->name, rtc);
+	ret = devm_request_irq(&pdev->dev, rtc->irq, st_rtc_handler,
+			       IRQF_NO_AUTOEN, pdev->name, rtc);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to request irq %i\n", rtc->irq);
 		return ret;
 	}
 
 	enable_irq_wake(rtc->irq);
-	disable_irq(rtc->irq);
 
-	rtc->clk = clk_get(&pdev->dev, NULL);
+	rtc->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(rtc->clk)) {
 		dev_err(&pdev->dev, "Unable to request clock\n");
 		return PTR_ERR(rtc->clk);
@@ -238,6 +237,7 @@
 
 	rtc->clkrate = clk_get_rate(rtc->clk);
 	if (!rtc->clkrate) {
+		clk_disable_unprepare(rtc->clk);
 		dev_err(&pdev->dev, "Unable to fetch clock rate\n");
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-sun6i.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-sun6i.c
@@ -128,7 +128,6 @@
 	unsigned int fixed_prescaler : 16;
 	unsigned int has_prescaler : 1;
 	unsigned int has_out_clk : 1;
-	unsigned int export_iosc : 1;
 	unsigned int has_losc_en : 1;
 	unsigned int has_auto_swt : 1;
 };
@@ -138,7 +137,7 @@
 	const struct sun6i_rtc_clk_data *data;
 	void __iomem *base;
 	int irq;
-	unsigned long alarm;
+	time64_t alarm;
 
 	struct clk_hw hw;
 	struct clk_hw *int_osc;
@@ -260,10 +259,8 @@
 	/* Yes, I know, this is ugly. */
 	sun6i_rtc = rtc;
 
-	/* Only read IOSC name from device tree if it is exported */
-	if (rtc->data->export_iosc)
-		of_property_read_string_index(node, "clock-output-names", 2,
-					      &iosc_name);
+	of_property_read_string_index(node, "clock-output-names", 2,
+				      &iosc_name);
 
 	rtc->int_osc = clk_hw_register_fixed_rate_with_accuracy(NULL,
 								iosc_name,
@@ -304,13 +301,10 @@
 		goto err_register;
 	}
 
-	clk_data->num = 2;
+	clk_data->num = 3;
 	clk_data->hws[0] = &rtc->hw;
 	clk_data->hws[1] = __clk_get_hw(rtc->ext_losc);
-	if (rtc->data->export_iosc) {
-		clk_data->hws[2] = rtc->int_osc;
-		clk_data->num = 3;
-	}
+	clk_data->hws[2] = rtc->int_osc;
 	of_clk_add_hw_provider(node, of_clk_hw_onecell_get, clk_data);
 	return;
 
@@ -350,7 +344,6 @@
 	.fixed_prescaler = 32,
 	.has_prescaler = 1,
 	.has_out_clk = 1,
-	.export_iosc = 1,
 };
 
 static void __init sun8i_h3_rtc_clk_init(struct device_node *node)
@@ -368,7 +361,6 @@
 	.fixed_prescaler = 32,
 	.has_prescaler = 1,
 	.has_out_clk = 1,
-	.export_iosc = 1,
 	.has_losc_en = 1,
 	.has_auto_swt = 1,
 };
@@ -510,10 +502,8 @@
 	struct sun6i_rtc_dev *chip = dev_get_drvdata(dev);
 	struct rtc_time *alrm_tm = &wkalrm->time;
 	struct rtc_time tm_now;
-	unsigned long time_now = 0;
-	unsigned long time_set = 0;
-	unsigned long time_gap = 0;
-	int ret = 0;
+	time64_t time_now, time_set;
+	int ret;
 
 	ret = sun6i_rtc_gettime(dev, &tm_now);
 	if (ret < 0) {
@@ -528,9 +518,7 @@
 		return -EINVAL;
 	}
 
-	time_gap = time_set - time_now;
-
-	if (time_gap > U32_MAX) {
+	if ((time_set - time_now) > U32_MAX) {
 		dev_err(dev, "Date too far in the future\n");
 		return -EINVAL;
 	}
@@ -539,7 +527,7 @@
 	writel(0, chip->base + SUN6I_ALRM_COUNTER);
 	usleep_range(100, 300);
 
-	writel(time_gap, chip->base + SUN6I_ALRM_COUNTER);
+	writel(time_set - time_now, chip->base + SUN6I_ALRM_COUNTER);
 	chip->alarm = time_set;
 
 	sun6i_rtc_setaie(wkalrm->enabled, chip);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-wm8350.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-wm8350.c
@@ -432,14 +432,21 @@
 		return ret;
 	}
 
-	wm8350_register_irq(wm8350, WM8350_IRQ_RTC_SEC,
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_RTC_SEC,
 			    wm8350_rtc_update_handler, 0,
 			    "RTC Seconds", wm8350);
+	if (ret)
+		return ret;
+
 	wm8350_mask_irq(wm8350, WM8350_IRQ_RTC_SEC);
 
-	wm8350_register_irq(wm8350, WM8350_IRQ_RTC_ALM,
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_RTC_ALM,
 			    wm8350_rtc_alarm_handler, 0,
 			    "RTC Alarm", wm8350);
+	if (ret) {
+		wm8350_free_irq(wm8350, WM8350_IRQ_RTC_SEC, wm8350);
+		return ret;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/rtc/rtc-zynqmp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/rtc/rtc-zynqmp.c
@@ -40,6 +40,12 @@
 #define RTC_CALIB_MASK		0x1FFFFF
 #define RTC_ALRM_MASK          BIT(1)
 #define RTC_MSEC               1000
+#define RTC_FR_MASK		0xF0000
+#define RTC_SEC_MAX_VAL		0xFFFFFFFF
+#define RTC_FR_MAX_TICKS	16
+#define RTC_OFFSET_MAX		150000
+#define RTC_OFFSET_MIN		-150000
+#define RTC_PPB			1000000000LL
 
 struct xlnx_rtc_dev {
 	struct rtc_device	*rtc;
@@ -184,12 +190,86 @@
 	writel(xrtcdev->calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
 }
 
+static int xlnx_rtc_read_offset(struct device *dev, long *offset)
+{
+	struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
+	unsigned long long rtc_ppb = RTC_PPB;
+	long offset_val;
+	unsigned int reg;
+	unsigned int tick_mult = do_div(rtc_ppb, xrtcdev->calibval);
+
+	reg = readl(xrtcdev->reg_base + RTC_CALIB_RD);
+
+	/* Offset with seconds ticks */
+	offset_val = reg & RTC_TICK_MASK;
+	offset_val = offset_val - xrtcdev->calibval;
+	offset_val = offset_val * tick_mult;
+
+	/* Offset with fractional ticks */
+	if (reg & RTC_FR_EN)
+		offset_val += ((reg & RTC_FR_MASK) >> RTC_FR_DATSHIFT)
+			* (tick_mult / RTC_FR_MAX_TICKS);
+	*offset = offset_val;
+
+	return 0;
+}
+
+static int xlnx_rtc_set_offset(struct device *dev, long offset)
+{
+	struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
+	unsigned long long rtc_ppb = RTC_PPB;
+	short int  max_tick;
+	unsigned char fract_tick = 0;
+	unsigned int calibval;
+	int fract_offset;
+	unsigned int tick_mult = do_div(rtc_ppb, xrtcdev->calibval);
+
+	/* Make sure offset value is within supported range */
+	if (offset < RTC_OFFSET_MIN || offset > RTC_OFFSET_MAX)
+		return -ERANGE;
+
+	/* Number ticks for given offset */
+	max_tick = div_s64_rem(offset, tick_mult, &fract_offset);
+
+	/* Number fractional ticks for given offset */
+	if (fract_offset) {
+		if (fract_offset < 0) {
+			fract_offset = fract_offset + tick_mult;
+			max_tick--;
+		}
+		if (fract_offset > (tick_mult / RTC_FR_MAX_TICKS)) {
+			for (fract_tick = 1; fract_tick < 16; fract_tick++) {
+				if (fract_offset <=
+				    (fract_tick *
+				     (tick_mult / RTC_FR_MAX_TICKS)))
+					break;
+			}
+		}
+	}
+
+	/* Zynqmp RTC uses second and fractional tick
+	 * counters for compensation
+	 */
+	calibval = max_tick + xrtcdev->calibval;
+
+	if (fract_tick)
+		calibval |= RTC_FR_EN;
+
+	calibval |= (fract_tick << RTC_FR_DATSHIFT);
+
+	writel(calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
+
+	return 0;
+}
+
 static const struct rtc_class_ops xlnx_rtc_ops = {
 	.set_time	  = xlnx_rtc_set_time,
 	.read_time	  = xlnx_rtc_read_time,
 	.read_alarm	  = xlnx_rtc_read_alarm,
 	.set_alarm	  = xlnx_rtc_set_alarm,
 	.alarm_irq_enable = xlnx_rtc_alarm_irq_enable,
+	.read_offset	  = xlnx_rtc_read_offset,
+	.set_offset	  = xlnx_rtc_set_offset,
 };
 
 static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd.c
@@ -8,9 +8,6 @@
  * Copyright IBM Corp. 1999, 2009
  */
 
-#define KMSG_COMPONENT "dasd"
-#define pr_fmt(fmt) KMSG_COMPONENT ": " fmt
-
 #include <linux/kmod.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
@@ -84,7 +81,8 @@
 static void dasd_profile_exit(struct dasd_profile *);
 static void dasd_hosts_init(struct dentry *, struct dasd_device *);
 static void dasd_hosts_exit(struct dasd_device *);
-
+static int dasd_handle_autoquiesce(struct dasd_device *, struct dasd_ccw_req *,
+				   unsigned int);
 /*
  * SECTION: Operations on the device structure.
  */
@@ -697,18 +695,20 @@
 	 * we count each request only once.
 	 */
 	device = cqr->startdev;
-	if (device->profile.data) {
-		counter = 1; /* request is not yet queued on the start device */
-		list_for_each(l, &device->ccw_queue)
-			if (++counter >= 31)
-				break;
-	}
+	if (!device->profile.data)
+		return;
+
+	spin_lock(get_ccwdev_lock(device->cdev));
+	counter = 1; /* request is not yet queued on the start device */
+	list_for_each(l, &device->ccw_queue)
+		if (++counter >= 31)
+			break;
+	spin_unlock(get_ccwdev_lock(device->cdev));
+
 	spin_lock(&device->profile.lock);
-	if (device->profile.data) {
-		device->profile.data->dasd_io_nr_req[counter]++;
-		if (rq_data_dir(req) == READ)
-			device->profile.data->dasd_read_nr_req[counter]++;
-	}
+	device->profile.data->dasd_io_nr_req[counter]++;
+	if (rq_data_dir(req) == READ)
+		device->profile.data->dasd_read_nr_req[counter]++;
 	spin_unlock(&device->profile.lock);
 }
 
@@ -1422,6 +1422,13 @@
 		if (!cqr->lpm)
 			cqr->lpm = dasd_path_get_opm(device);
 	}
+	/*
+	 * remember the amount of formatted tracks to prevent double format on
+	 * ESE devices
+	 */
+	if (cqr->block)
+		cqr->trkcount = atomic_read(&cqr->block->trkcount);
+
 	if (cqr->cpmode == 1) {
 		rc = ccw_device_tm_start(device->cdev, cqr->cpaddr,
 					 (long) cqr, cqr->lpm);
@@ -1615,9 +1622,15 @@
 	if (!sense)
 		return 0;
 
-	return !!(sense[1] & SNS1_NO_REC_FOUND) ||
-		!!(sense[1] & SNS1_FILE_PROTECTED) ||
-		scsw_cstat(&irb->scsw) == SCHN_STAT_INCORR_LEN;
+	if (sense[1] & SNS1_NO_REC_FOUND)
+		return 1;
+
+	if ((sense[1] & SNS1_INV_TRACK_FORMAT) &&
+	    scsw_is_tm(&irb->scsw) &&
+	    !(sense[2] & SNS2_ENV_DATA_PRESENT))
+		return 1;
+
+	return 0;
 }
 
 static int dasd_ese_oos_cond(u8 *sense)
@@ -1638,7 +1651,8 @@
 	struct dasd_device *device;
 	unsigned long now;
 	int nrf_suppressed = 0;
-	int fp_suppressed = 0;
+	int it_suppressed = 0;
+	struct request *req;
 	u8 *sense = NULL;
 	int expires;
 
@@ -1692,8 +1706,9 @@
 		 */
 		sense = dasd_get_sense(irb);
 		if (sense) {
-			fp_suppressed = (sense[1] & SNS1_FILE_PROTECTED) &&
-				test_bit(DASD_CQR_SUPPRESS_FP, &cqr->flags);
+			it_suppressed =	(sense[1] & SNS1_INV_TRACK_FORMAT) &&
+				!(sense[2] & SNS2_ENV_DATA_PRESENT) &&
+				test_bit(DASD_CQR_SUPPRESS_IT, &cqr->flags);
 			nrf_suppressed = (sense[1] & SNS1_NO_REC_FOUND) &&
 				test_bit(DASD_CQR_SUPPRESS_NRF, &cqr->flags);
 
@@ -1708,7 +1723,7 @@
 				return;
 			}
 		}
-		if (!(fp_suppressed || nrf_suppressed))
+		if (!(it_suppressed || nrf_suppressed))
 			device->discipline->dump_sense_dbf(device, irb, "int");
 
 		if (device->features & DASD_FEATURE_ERPLOG)
@@ -1739,7 +1754,12 @@
 	}
 
 	if (dasd_ese_needs_format(cqr->block, irb)) {
-		if (rq_data_dir((struct request *)cqr->callback_data) == READ) {
+		req = dasd_get_callback_data(cqr);
+		if (!req) {
+			cqr->status = DASD_CQR_ERROR;
+			return;
+		}
+		if (rq_data_dir(req) == READ) {
 			device->discipline->ese_read(cqr, irb);
 			cqr->status = DASD_CQR_SUCCESS;
 			cqr->stopclk = now;
@@ -2334,7 +2354,7 @@
 		/* Non-temporary stop condition will trigger fail fast */
 		if (device->stopped & ~DASD_STOPPED_PENDING &&
 		    test_bit(DASD_CQR_FLAGS_FAILFAST, &cqr->flags) &&
-		    (!dasd_eer_enabled(device))) {
+		    !dasd_eer_enabled(device) && device->aq_mask == 0) {
 			cqr->status = DASD_CQR_FAILED;
 			cqr->intrc = -ENOLINK;
 			continue;
@@ -2461,14 +2481,17 @@
 	rc = 0;
 	list_for_each_entry_safe(cqr, n, ccw_queue, blocklist) {
 		/*
-		 * In some cases the 'File Protected' or 'Incorrect Length'
-		 * error might be expected and error recovery would be
-		 * unnecessary in these cases.	Check if the according suppress
-		 * bit is set.
+		 * In some cases certain errors might be expected and
+		 * error recovery would be unnecessary in these cases.
+		 * Check if the according suppress bit is set.
 		 */
 		sense = dasd_get_sense(&cqr->irb);
-		if (sense && sense[1] & SNS1_FILE_PROTECTED &&
-		    test_bit(DASD_CQR_SUPPRESS_FP, &cqr->flags))
+		if (sense && (sense[1] & SNS1_INV_TRACK_FORMAT) &&
+		    !(sense[2] & SNS2_ENV_DATA_PRESENT) &&
+		    test_bit(DASD_CQR_SUPPRESS_IT, &cqr->flags))
+			continue;
+		if (sense && (sense[1] & SNS1_NO_REC_FOUND) &&
+		    test_bit(DASD_CQR_SUPPRESS_NRF, &cqr->flags))
 			continue;
 		if (scsw_cstat(&cqr->irb.scsw) == 0x40 &&
 		    test_bit(DASD_CQR_SUPPRESS_IL, &cqr->flags))
@@ -2762,8 +2785,7 @@
 		 * complete a request partially.
 		 */
 		if (proc_bytes) {
-			blk_update_request(req, BLK_STS_OK,
-					   blk_rq_bytes(req) - proc_bytes);
+			blk_update_request(req, BLK_STS_OK, proc_bytes);
 			blk_mq_requeue_request(req, true);
 		} else if (likely(!blk_should_fake_timeout(req->q))) {
 			blk_mq_complete_request(req);
@@ -2811,20 +2833,18 @@
 			dasd_log_sense(cqr, &cqr->irb);
 		}
 
-		/* First of all call extended error reporting. */
-		if (dasd_eer_enabled(base) &&
-		    cqr->status == DASD_CQR_FAILED) {
-			dasd_eer_write(base, cqr, DASD_EER_FATALERROR);
-
-			/* restart request  */
+		/*
+		 * First call extended error reporting and check for autoquiesce
+		 */
+		spin_lock_irqsave(get_ccwdev_lock(base->cdev), flags);
+		if (cqr->status == DASD_CQR_FAILED &&
+		    dasd_handle_autoquiesce(base, cqr, DASD_EER_FATALERROR)) {
 			cqr->status = DASD_CQR_FILLED;
 			cqr->retries = 255;
-			spin_lock_irqsave(get_ccwdev_lock(base->cdev), flags);
-			dasd_device_set_stop_bits(base, DASD_STOPPED_QUIESCE);
-			spin_unlock_irqrestore(get_ccwdev_lock(base->cdev),
-					       flags);
+			spin_unlock_irqrestore(get_ccwdev_lock(base->cdev), flags);
 			goto restart;
 		}
+		spin_unlock_irqrestore(get_ccwdev_lock(base->cdev), flags);
 
 		/* Process finished ERP request. */
 		if (cqr->refers) {
@@ -2866,7 +2886,7 @@
 		/* Non-temporary stop condition will trigger fail fast */
 		if (block->base->stopped & ~DASD_STOPPED_PENDING &&
 		    test_bit(DASD_CQR_FLAGS_FAILFAST, &cqr->flags) &&
-		    (!dasd_eer_enabled(block->base))) {
+		    !dasd_eer_enabled(block->base) && block->base->aq_mask == 0) {
 			cqr->status = DASD_CQR_FAILED;
 			cqr->intrc = -ENOLINK;
 			dasd_schedule_block_bh(block);
@@ -2936,41 +2956,32 @@
  * Requeue a request back to the block request queue
  * only works for block requests
  */
-static int _dasd_requeue_request(struct dasd_ccw_req *cqr)
+static void _dasd_requeue_request(struct dasd_ccw_req *cqr)
 {
-	struct dasd_block *block = cqr->block;
 	struct request *req;
 
-	if (!block)
-		return -EINVAL;
 	/*
 	 * If the request is an ERP request there is nothing to requeue.
 	 * This will be done with the remaining original request.
 	 */
 	if (cqr->refers)
-		return 0;
+		return;
 	spin_lock_irq(&cqr->dq->lock);
 	req = (struct request *) cqr->callback_data;
-	blk_mq_requeue_request(req, false);
+	blk_mq_requeue_request(req, true);
 	spin_unlock_irq(&cqr->dq->lock);
 
-	return 0;
+	return;
 }
 
-/*
- * Go through all request on the dasd_block request queue, cancel them
- * on the respective dasd_device, and return them to the generic
- * block layer.
- */
-static int dasd_flush_block_queue(struct dasd_block *block)
+static int _dasd_requests_to_flushqueue(struct dasd_block *block,
+					struct list_head *flush_queue)
 {
 	struct dasd_ccw_req *cqr, *n;
-	int rc, i;
-	struct list_head flush_queue;
 	unsigned long flags;
+	int rc, i;
 
-	INIT_LIST_HEAD(&flush_queue);
-	spin_lock_bh(&block->queue_lock);
+	spin_lock_irqsave(&block->queue_lock, flags);
 	rc = 0;
 restart:
 	list_for_each_entry_safe(cqr, n, &block->ccw_queue, blocklist) {
@@ -2985,13 +2996,32 @@
 		 * is returned from the dasd_device layer.
 		 */
 		cqr->callback = _dasd_wake_block_flush_cb;
-		for (i = 0; cqr != NULL; cqr = cqr->refers, i++)
-			list_move_tail(&cqr->blocklist, &flush_queue);
+		for (i = 0; cqr; cqr = cqr->refers, i++)
+			list_move_tail(&cqr->blocklist, flush_queue);
 		if (i > 1)
 			/* moved more than one request - need to restart */
 			goto restart;
 	}
-	spin_unlock_bh(&block->queue_lock);
+	spin_unlock_irqrestore(&block->queue_lock, flags);
+
+	return rc;
+}
+
+/*
+ * Go through all request on the dasd_block request queue, cancel them
+ * on the respective dasd_device, and return them to the generic
+ * block layer.
+ */
+static int dasd_flush_block_queue(struct dasd_block *block)
+{
+	struct dasd_ccw_req *cqr, *n;
+	struct list_head flush_queue;
+	unsigned long flags;
+	int rc;
+
+	INIT_LIST_HEAD(&flush_queue);
+	rc = _dasd_requests_to_flushqueue(block, &flush_queue);
+
 	/* Now call the callback function of flushed requests */
 restart_cb:
 	list_for_each_entry_safe(cqr, n, &flush_queue, blocklist) {
@@ -3428,8 +3458,7 @@
 
 	ret = ccw_device_set_online(cdev);
 	if (ret)
-		pr_warn("%s: Setting the DASD online failed with rc=%d\n",
-			dev_name(&cdev->dev), ret);
+		dev_warn(&cdev->dev, "Setting the DASD online failed with rc=%d\n", ret);
 }
 
 /*
@@ -3516,8 +3545,11 @@
 {
 	struct dasd_discipline *discipline;
 	struct dasd_device *device;
+	struct device *dev;
 	int rc;
 
+	dev = &cdev->dev;
+
 	/* first online clears initial online feature flag */
 	dasd_set_feature(cdev, DASD_FEATURE_INITIAL_ONLINE, 0);
 	device = dasd_create_device(cdev);
@@ -3530,11 +3562,10 @@
 			/* Try to load the required module. */
 			rc = request_module(DASD_DIAG_MOD);
 			if (rc) {
-				pr_warn("%s Setting the DASD online failed "
-					"because the required module %s "
-					"could not be loaded (rc=%d)\n",
-					dev_name(&cdev->dev), DASD_DIAG_MOD,
-					rc);
+				dev_warn(dev, "Setting the DASD online failed "
+					 "because the required module %s "
+					 "could not be loaded (rc=%d)\n",
+					 DASD_DIAG_MOD, rc);
 				dasd_delete_device(device);
 				return -ENODEV;
 			}
@@ -3542,8 +3573,7 @@
 		/* Module init could have failed, so check again here after
 		 * request_module(). */
 		if (!dasd_diag_discipline_pointer) {
-			pr_warn("%s Setting the DASD online failed because of missing DIAG discipline\n",
-				dev_name(&cdev->dev));
+			dev_warn(dev, "Setting the DASD online failed because of missing DIAG discipline\n");
 			dasd_delete_device(device);
 			return -ENODEV;
 		}
@@ -3553,37 +3583,33 @@
 		dasd_delete_device(device);
 		return -EINVAL;
 	}
+	device->base_discipline = base_discipline;
 	if (!try_module_get(discipline->owner)) {
-		module_put(base_discipline->owner);
 		dasd_delete_device(device);
 		return -EINVAL;
 	}
-	device->base_discipline = base_discipline;
 	device->discipline = discipline;
 
 	/* check_device will allocate block device if necessary */
 	rc = discipline->check_device(device);
 	if (rc) {
-		pr_warn("%s Setting the DASD online with discipline %s failed with rc=%i\n",
-			dev_name(&cdev->dev), discipline->name, rc);
-		module_put(discipline->owner);
-		module_put(base_discipline->owner);
+		dev_warn(dev, "Setting the DASD online with discipline %s failed with rc=%i\n",
+			 discipline->name, rc);
 		dasd_delete_device(device);
 		return rc;
 	}
 
 	dasd_set_target_state(device, DASD_STATE_ONLINE);
 	if (device->state <= DASD_STATE_KNOWN) {
-		pr_warn("%s Setting the DASD online failed because of a missing discipline\n",
-			dev_name(&cdev->dev));
+		dev_warn(dev, "Setting the DASD online failed because of a missing discipline\n");
 		rc = -ENODEV;
 		dasd_set_target_state(device, DASD_STATE_NEW);
 		if (device->block)
 			dasd_free_block(device->block);
 		dasd_delete_device(device);
-	} else
-		pr_debug("dasd_generic device %s found\n",
-				dev_name(&cdev->dev));
+	} else {
+		dev_dbg(dev, "dasd_generic device found\n");
+	}
 
 	wait_event(dasd_init_waitq, _wait_for_device(device));
 
@@ -3594,10 +3620,13 @@
 
 int dasd_generic_set_offline(struct ccw_device *cdev)
 {
+	int max_count, open_count, rc;
 	struct dasd_device *device;
 	struct dasd_block *block;
-	int max_count, open_count, rc;
 	unsigned long flags;
+	struct device *dev;
+
+	dev = &cdev->dev;
 
 	rc = 0;
 	spin_lock_irqsave(get_ccwdev_lock(cdev), flags);
@@ -3618,11 +3647,10 @@
 		open_count = atomic_read(&device->block->open_count);
 		if (open_count > max_count) {
 			if (open_count > 0)
-				pr_warn("%s: The DASD cannot be set offline with open count %i\n",
-					dev_name(&cdev->dev), open_count);
+				dev_warn(dev, "The DASD cannot be set offline with open count %i\n",
+					 open_count);
 			else
-				pr_warn("%s: The DASD cannot be set offline while it is in use\n",
-					dev_name(&cdev->dev));
+				dev_warn(dev, "The DASD cannot be set offline while it is in use\n");
 			rc = -EBUSY;
 			goto out_err;
 		}
@@ -3719,8 +3747,8 @@
 	dev_warn(&device->cdev->dev, "No operational channel path is left "
 		 "for the device\n");
 	DBF_DEV_EVENT(DBF_WARNING, device, "%s", "last path gone");
-	/* First of all call extended error reporting. */
-	dasd_eer_write(device, NULL, DASD_EER_NOPATH);
+	/* First call extended error reporting and check for autoquiesce. */
+	dasd_handle_autoquiesce(device, NULL, DASD_EER_NOPATH);
 
 	if (device->state < DASD_STATE_BASIC)
 		return 0;
@@ -3853,7 +3881,8 @@
 			 "No verified channel paths remain for the device\n");
 		DBF_DEV_EVENT(DBF_WARNING, device,
 			      "%s", "last verified path gone");
-		dasd_eer_write(device, NULL, DASD_EER_NOPATH);
+		/* First call extended error reporting and check for autoquiesce. */
+		dasd_handle_autoquiesce(device, NULL, DASD_EER_NOPATH);
 		dasd_device_set_stop_bits(device,
 					  DASD_STOPPED_DC_WAIT);
 	}
@@ -3875,7 +3904,8 @@
 void dasd_generic_space_exhaust(struct dasd_device *device,
 				struct dasd_ccw_req *cqr)
 {
-	dasd_eer_write(device, NULL, DASD_EER_NOSPC);
+	/* First call extended error reporting and check for autoquiesce. */
+	dasd_handle_autoquiesce(device, NULL, DASD_EER_NOSPC);
 
 	if (device->state < DASD_STATE_BASIC)
 		return;
@@ -3914,75 +3944,36 @@
  */
 static int dasd_generic_requeue_all_requests(struct dasd_device *device)
 {
+	struct dasd_block *block = device->block;
 	struct list_head requeue_queue;
 	struct dasd_ccw_req *cqr, *n;
-	struct dasd_ccw_req *refers;
 	int rc;
 
-	INIT_LIST_HEAD(&requeue_queue);
-	spin_lock_irq(get_ccwdev_lock(device->cdev));
-	rc = 0;
-	list_for_each_entry_safe(cqr, n, &device->ccw_queue, devlist) {
-		/* Check status and move request to flush_queue */
-		if (cqr->status == DASD_CQR_IN_IO) {
-			rc = device->discipline->term_IO(cqr);
-			if (rc) {
-				/* unable to terminate requeust */
-				dev_err(&device->cdev->dev,
-					"Unable to terminate request %p "
-					"on suspend\n", cqr);
-				spin_unlock_irq(get_ccwdev_lock(device->cdev));
-				dasd_put_device(device);
-				return rc;
-			}
-		}
-		list_move_tail(&cqr->devlist, &requeue_queue);
-	}
-	spin_unlock_irq(get_ccwdev_lock(device->cdev));
-
-	list_for_each_entry_safe(cqr, n, &requeue_queue, devlist) {
-		wait_event(dasd_flush_wq,
-			   (cqr->status != DASD_CQR_CLEAR_PENDING));
+	if (!block)
+		return 0;
 
-		/*
-		 * requeue requests to blocklayer will only work
-		 * for block device requests
-		 */
-		if (_dasd_requeue_request(cqr))
-			continue;
+	INIT_LIST_HEAD(&requeue_queue);
+	rc = _dasd_requests_to_flushqueue(block, &requeue_queue);
 
-		/* remove requests from device and block queue */
-		list_del_init(&cqr->devlist);
-		while (cqr->refers != NULL) {
-			refers = cqr->refers;
-			/* remove the request from the block queue */
-			list_del(&cqr->blocklist);
-			/* free the finished erp request */
-			dasd_free_erp_request(cqr, cqr->memdev);
-			cqr = refers;
+	/* Now call the callback function of flushed requests */
+restart_cb:
+	list_for_each_entry_safe(cqr, n, &requeue_queue, blocklist) {
+		wait_event(dasd_flush_wq, (cqr->status < DASD_CQR_QUEUED));
+		/* Process finished ERP request. */
+		if (cqr->refers) {
+			spin_lock_bh(&block->queue_lock);
+			__dasd_process_erp(block->base, cqr);
+			spin_unlock_bh(&block->queue_lock);
+			/* restart list_for_xx loop since dasd_process_erp
+			 * might remove multiple elements
+			 */
+			goto restart_cb;
 		}
-
-		/*
-		 * _dasd_requeue_request already checked for a valid
-		 * blockdevice, no need to check again
-		 * all erp requests (cqr->refers) have a cqr->block
-		 * pointer copy from the original cqr
-		 */
+		_dasd_requeue_request(cqr);
 		list_del_init(&cqr->blocklist);
 		cqr->block->base->discipline->free_cp(
 			cqr, (struct request *) cqr->callback_data);
 	}
-
-	/*
-	 * if requests remain then they are internal request
-	 * and go back to the device queue
-	 */
-	if (!list_empty(&requeue_queue)) {
-		/* move freeze_queue to start of the ccw_queue */
-		spin_lock_irq(get_ccwdev_lock(device->cdev));
-		list_splice_tail(&requeue_queue, &device->ccw_queue);
-		spin_unlock_irq(get_ccwdev_lock(device->cdev));
-	}
 	dasd_schedule_device_bh(device);
 	return rc;
 }
@@ -4007,6 +3998,31 @@
 }
 EXPORT_SYMBOL(dasd_schedule_requeue);
 
+static int dasd_handle_autoquiesce(struct dasd_device *device,
+				   struct dasd_ccw_req *cqr,
+				   unsigned int reason)
+{
+	/* in any case write eer message with reason */
+	if (dasd_eer_enabled(device))
+		dasd_eer_write(device, cqr, reason);
+
+	if (!test_bit(reason, &device->aq_mask))
+		return 0;
+
+	/* notify eer about autoquiesce */
+	if (dasd_eer_enabled(device))
+		dasd_eer_write(device, NULL, DASD_EER_AUTOQUIESCE);
+
+	dev_info(&device->cdev->dev,
+		 "The DASD has been put in the quiesce state\n");
+	dasd_device_set_stop_bits(device, DASD_STOPPED_QUIESCE);
+
+	if (device->features & DASD_FEATURE_REQUEUEQUIESCE)
+		dasd_schedule_requeue(device);
+
+	return 1;
+}
+
 static struct dasd_ccw_req *dasd_generic_build_rdc(struct dasd_device *device,
 						   int rdc_buffer_size,
 						   int magic)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_3990_erp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_3990_erp.c
@@ -1401,14 +1401,8 @@
 
 	struct dasd_device *device = erp->startdev;
 
-	/*
-	 * In some cases the 'File Protected' error might be expected and
-	 * log messages shouldn't be written then.
-	 * Check if the according suppress bit is set.
-	 */
-	if (!test_bit(DASD_CQR_SUPPRESS_FP, &erp->flags))
-		dev_err(&device->cdev->dev,
-			"Accessing the DASD failed because of a hardware error\n");
+	dev_err(&device->cdev->dev,
+		"Accessing the DASD failed because of a hardware error\n");
 
 	return dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
 
@@ -2436,7 +2430,7 @@
 	erp->block    = cqr->block;
 	erp->magic    = cqr->magic;
 	erp->expires  = cqr->expires;
-	erp->retries  = 256;
+	erp->retries  = device->default_retries;
 	erp->buildclk = get_tod_clock();
 	erp->status = DASD_CQR_FILLED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_alias.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_alias.c
@@ -675,12 +675,12 @@
 struct dasd_device *dasd_alias_get_start_dev(struct dasd_device *base_device)
 {
 	struct dasd_eckd_private *alias_priv, *private = base_device->private;
-	struct alias_pav_group *group = private->pavgroup;
 	struct alias_lcu *lcu = private->lcu;
 	struct dasd_device *alias_device;
+	struct alias_pav_group *group;
 	unsigned long flags;
 
-	if (!group || !lcu)
+	if (!lcu)
 		return NULL;
 	if (lcu->pav == NO_PAV ||
 	    lcu->flags & (NEED_UAC_UPDATE | UPDATE_PENDING))
@@ -697,6 +697,11 @@
 	}
 
 	spin_lock_irqsave(&lcu->lock, flags);
+	group = private->pavgroup;
+	if (!group) {
+		spin_unlock_irqrestore(&lcu->lock, flags);
+		return NULL;
+	}
 	alias_device = group->next;
 	if (!alias_device) {
 		if (list_empty(&group->aliaslist)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_devmap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_devmap.c
@@ -26,7 +26,6 @@
 
 /* This is ugly... */
 #define PRINTK_HEADER "dasd_devmap:"
-#define DASD_BUS_ID_SIZE 20
 #define DASD_MAX_PARAMS 256
 
 #include "dasd_int.h"
@@ -50,6 +49,7 @@
         unsigned int devindex;
         unsigned short features;
 	struct dasd_device *device;
+	struct dasd_copy_relation *copy;
 };
 
 /*
@@ -130,7 +130,7 @@
 /*
  * Read a device busid/devno from a string.
  */
-static int __init dasd_busid(char *str, int *id0, int *id1, int *devno)
+static int dasd_busid(char *str, int *id0, int *id1, int *devno)
 {
 	unsigned int val;
 	char *tok;
@@ -438,16 +438,12 @@
 	return devmap;
 }
 
-/*
- * Find devmap for device with given bus_id.
- */
 static struct dasd_devmap *
-dasd_find_busid(const char *bus_id)
+dasd_find_busid_locked(const char *bus_id)
 {
 	struct dasd_devmap *devmap, *tmp;
 	int hash;
 
-	spin_lock(&dasd_devmap_lock);
 	devmap = ERR_PTR(-ENODEV);
 	hash = dasd_hash_busid(bus_id);
 	list_for_each_entry(tmp, &dasd_hashlists[hash], list) {
@@ -456,6 +452,19 @@
 			break;
 		}
 	}
+	return devmap;
+}
+
+/*
+ * Find devmap for device with given bus_id.
+ */
+static struct dasd_devmap *
+dasd_find_busid(const char *bus_id)
+{
+	struct dasd_devmap *devmap;
+
+	spin_lock(&dasd_devmap_lock);
+	devmap = dasd_find_busid_locked(bus_id);
 	spin_unlock(&dasd_devmap_lock);
 	return devmap;
 }
@@ -585,6 +594,238 @@
 }
 
 /*
+ * allocate a PPRC data structure and call the discipline function to fill
+ */
+static int dasd_devmap_get_pprc_status(struct dasd_device *device,
+				       struct dasd_pprc_data_sc4 **data)
+{
+	struct dasd_pprc_data_sc4 *temp;
+
+	if (!device->discipline || !device->discipline->pprc_status) {
+		dev_warn(&device->cdev->dev, "Unable to query copy relation status\n");
+		return -EOPNOTSUPP;
+	}
+	temp = kzalloc(sizeof(*temp), GFP_KERNEL);
+	if (!temp)
+		return -ENOMEM;
+
+	/* get PPRC information from storage */
+	if (device->discipline->pprc_status(device, temp)) {
+		dev_warn(&device->cdev->dev, "Error during copy relation status query\n");
+		kfree(temp);
+		return -EINVAL;
+	}
+	*data = temp;
+
+	return 0;
+}
+
+/*
+ * find an entry in a PPRC device_info array by a given UID
+ * depending on the primary/secondary state of the device it has to be
+ * matched with the respective fields
+ */
+static int dasd_devmap_entry_from_pprc_data(struct dasd_pprc_data_sc4 *data,
+					    struct dasd_uid uid,
+					    bool primary)
+{
+	int i;
+
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (primary) {
+			if (data->dev_info[i].prim_cu_ssid == uid.ssid &&
+			    data->dev_info[i].primary == uid.real_unit_addr)
+				return i;
+		} else {
+			if (data->dev_info[i].sec_cu_ssid == uid.ssid &&
+			    data->dev_info[i].secondary == uid.real_unit_addr)
+				return i;
+		}
+	}
+	return -1;
+}
+
+/*
+ * check the consistency of a specified copy relation by checking
+ * the following things:
+ *
+ *   - is the given device part of a copy pair setup
+ *   - does the state of the device match the state in the PPRC status data
+ *   - does the device UID match with the UID in the PPRC status data
+ *   - to prevent misrouted IO check if the given device is present in all
+ *     related PPRC status data
+ */
+static int dasd_devmap_check_copy_relation(struct dasd_device *device,
+					   struct dasd_copy_entry *entry,
+					   struct dasd_pprc_data_sc4 *data,
+					   struct dasd_copy_relation *copy)
+{
+	struct dasd_pprc_data_sc4 *tmp_dat;
+	struct dasd_device *tmp_dev;
+	struct dasd_uid uid;
+	int i, j;
+
+	if (!device->discipline || !device->discipline->get_uid ||
+	    device->discipline->get_uid(device, &uid))
+		return 1;
+
+	i = dasd_devmap_entry_from_pprc_data(data, uid, entry->primary);
+	if (i < 0) {
+		dev_warn(&device->cdev->dev, "Device not part of a copy relation\n");
+		return 1;
+	}
+
+	/* double check which role the current device has */
+	if (entry->primary) {
+		if (data->dev_info[i].flags & 0x80) {
+			dev_warn(&device->cdev->dev, "Copy pair secondary is setup as primary\n");
+			return 1;
+		}
+		if (data->dev_info[i].prim_cu_ssid != uid.ssid ||
+		    data->dev_info[i].primary != uid.real_unit_addr) {
+			dev_warn(&device->cdev->dev,
+				 "Primary device %s does not match copy pair status primary device %04x\n",
+				 dev_name(&device->cdev->dev),
+				 data->dev_info[i].prim_cu_ssid |
+				 data->dev_info[i].primary);
+			return 1;
+		}
+	} else {
+		if (!(data->dev_info[i].flags & 0x80)) {
+			dev_warn(&device->cdev->dev, "Copy pair primary is setup as secondary\n");
+			return 1;
+		}
+		if (data->dev_info[i].sec_cu_ssid != uid.ssid ||
+		    data->dev_info[i].secondary != uid.real_unit_addr) {
+			dev_warn(&device->cdev->dev,
+				 "Secondary device %s does not match copy pair status secondary device %04x\n",
+				 dev_name(&device->cdev->dev),
+				 data->dev_info[i].sec_cu_ssid |
+				 data->dev_info[i].secondary);
+			return 1;
+		}
+	}
+
+	/*
+	 * the current device has to be part of the copy relation of all
+	 * entries to prevent misrouted IO to another copy pair
+	 */
+	for (j = 0; j < DASD_CP_ENTRIES; j++) {
+		if (entry == &copy->entry[j])
+			tmp_dev = device;
+		else
+			tmp_dev = copy->entry[j].device;
+
+		if (!tmp_dev)
+			continue;
+
+		if (dasd_devmap_get_pprc_status(tmp_dev, &tmp_dat))
+			return 1;
+
+		if (dasd_devmap_entry_from_pprc_data(tmp_dat, uid, entry->primary) < 0) {
+			dev_warn(&tmp_dev->cdev->dev,
+				 "Copy pair relation does not contain device: %s\n",
+				 dev_name(&device->cdev->dev));
+			kfree(tmp_dat);
+			return 1;
+		}
+		kfree(tmp_dat);
+	}
+	return 0;
+}
+
+/* delete device from copy relation entry */
+static void dasd_devmap_delete_copy_relation_device(struct dasd_device *device)
+{
+	struct dasd_copy_relation *copy;
+	int i;
+
+	if (!device->copy)
+		return;
+
+	copy = device->copy;
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (copy->entry[i].device == device)
+			copy->entry[i].device = NULL;
+	}
+	dasd_put_device(device);
+	device->copy = NULL;
+}
+
+/*
+ * read all required information for a copy relation setup and setup the device
+ * accordingly
+ */
+int dasd_devmap_set_device_copy_relation(struct ccw_device *cdev,
+					 bool pprc_enabled)
+{
+	struct dasd_pprc_data_sc4 *data = NULL;
+	struct dasd_copy_entry *entry = NULL;
+	struct dasd_copy_relation *copy;
+	struct dasd_devmap *devmap;
+	struct dasd_device *device;
+	int i, rc = 0;
+
+	devmap = dasd_devmap_from_cdev(cdev);
+	if (IS_ERR(devmap))
+		return PTR_ERR(devmap);
+
+	device = devmap->device;
+	if (!device)
+		return -ENODEV;
+
+	copy = devmap->copy;
+	/* no copy pair setup for this device */
+	if (!copy)
+		goto out;
+
+	rc = dasd_devmap_get_pprc_status(device, &data);
+	if (rc)
+		return rc;
+
+	/* print error if PPRC is requested but not enabled on storage server */
+	if (!pprc_enabled) {
+		dev_err(&cdev->dev, "Copy relation not enabled on storage server\n");
+		rc = -EINVAL;
+		goto out;
+	}
+
+	if (!data->dev_info[0].state) {
+		dev_warn(&device->cdev->dev, "Copy pair setup requested for device not in copy relation\n");
+		rc = -EINVAL;
+		goto out;
+	}
+	/* find entry */
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (copy->entry[i].configured &&
+		    strncmp(dev_name(&cdev->dev),
+			    copy->entry[i].busid, DASD_BUS_ID_SIZE) == 0) {
+			entry = &copy->entry[i];
+			break;
+		}
+	}
+	if (!entry) {
+		dev_warn(&device->cdev->dev, "Copy relation entry not found\n");
+		rc = -EINVAL;
+		goto out;
+	}
+	/* check if the copy relation is valid */
+	if (dasd_devmap_check_copy_relation(device, entry, data, copy)) {
+		dev_warn(&device->cdev->dev, "Copy relation faulty\n");
+		rc = -EINVAL;
+		goto out;
+	}
+
+	dasd_get_device(device);
+	copy->entry[i].device = device;
+	device->copy = copy;
+out:
+	kfree(data);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(dasd_devmap_set_device_copy_relation);
+
+/*
  * Wait queue for dasd_delete_device waits.
  */
 static DECLARE_WAIT_QUEUE_HEAD(dasd_delete_wq);
@@ -617,6 +858,8 @@
 	dev_set_drvdata(&device->cdev->dev, NULL);
 	spin_unlock_irqrestore(get_ccwdev_lock(device->cdev), flags);
 
+	/* Removve copy relation */
+	dasd_devmap_delete_copy_relation_device(device);
 	/*
 	 * Drop ref_count by 3, one for the devmap reference, one for
 	 * the cdev reference and one for the passed reference.
@@ -1683,6 +1926,313 @@
 static struct kobj_attribute path_fcs_attribute =
 	__ATTR(fc_security, 0444, dasd_path_fcs_show, NULL);
 
+/*
+ * print copy relation in the form
+ * primary,secondary[1] primary,secondary[2], ...
+ */
+static ssize_t
+dasd_copy_pair_show(struct device *dev,
+		    struct device_attribute *attr, char *buf)
+{
+	char prim_busid[DASD_BUS_ID_SIZE];
+	struct dasd_copy_relation *copy;
+	struct dasd_devmap *devmap;
+	int len = 0;
+	int i;
+
+	devmap = dasd_find_busid(dev_name(dev));
+	if (IS_ERR(devmap))
+		return -ENODEV;
+
+	if (!devmap->copy)
+		return -ENODEV;
+
+	copy = devmap->copy;
+	/* find primary */
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (copy->entry[i].configured && copy->entry[i].primary) {
+			strscpy(prim_busid, copy->entry[i].busid,
+				DASD_BUS_ID_SIZE);
+			break;
+		}
+	}
+	if (!copy->entry[i].primary)
+		goto out;
+
+	/* print all secondary */
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (copy->entry[i].configured && !copy->entry[i].primary)
+			len += sysfs_emit_at(buf, len, "%s,%s ", prim_busid,
+					     copy->entry[i].busid);
+	}
+
+	len += sysfs_emit_at(buf, len, "\n");
+out:
+	return len;
+}
+
+static int dasd_devmap_set_copy_relation(struct dasd_devmap *devmap,
+					 struct dasd_copy_relation *copy,
+					 char *busid, bool primary)
+{
+	int i;
+
+	/* find free entry */
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		/* current bus_id already included, nothing to do */
+		if (copy->entry[i].configured &&
+		    strncmp(copy->entry[i].busid, busid, DASD_BUS_ID_SIZE) == 0)
+			return 0;
+
+		if (!copy->entry[i].configured)
+			break;
+	}
+	if (i == DASD_CP_ENTRIES)
+		return -EINVAL;
+
+	copy->entry[i].configured = true;
+	strscpy(copy->entry[i].busid, busid, DASD_BUS_ID_SIZE);
+	if (primary) {
+		copy->active = &copy->entry[i];
+		copy->entry[i].primary = true;
+	}
+	if (!devmap->copy)
+		devmap->copy = copy;
+
+	return 0;
+}
+
+static void dasd_devmap_del_copy_relation(struct dasd_copy_relation *copy,
+					  char *busid)
+{
+	int i;
+
+	spin_lock(&dasd_devmap_lock);
+	/* find entry */
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (copy->entry[i].configured &&
+		    strncmp(copy->entry[i].busid, busid, DASD_BUS_ID_SIZE) == 0)
+			break;
+	}
+	if (i == DASD_CP_ENTRIES || !copy->entry[i].configured) {
+		spin_unlock(&dasd_devmap_lock);
+		return;
+	}
+
+	copy->entry[i].configured = false;
+	memset(copy->entry[i].busid, 0, DASD_BUS_ID_SIZE);
+	if (copy->active == &copy->entry[i]) {
+		copy->active = NULL;
+		copy->entry[i].primary = false;
+	}
+	spin_unlock(&dasd_devmap_lock);
+}
+
+static int dasd_devmap_clear_copy_relation(struct device *dev)
+{
+	struct dasd_copy_relation *copy;
+	struct dasd_devmap *devmap;
+	int i, rc = 1;
+
+	devmap = dasd_devmap_from_cdev(to_ccwdev(dev));
+	if (IS_ERR(devmap))
+		return 1;
+
+	spin_lock(&dasd_devmap_lock);
+	if (!devmap->copy)
+		goto out;
+
+	copy = devmap->copy;
+	/* first check if all secondary devices are offline*/
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (!copy->entry[i].configured)
+			continue;
+
+		if (copy->entry[i].device == copy->active->device)
+			continue;
+
+		if (copy->entry[i].device)
+			goto out;
+	}
+	/* clear all devmap entries */
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (strlen(copy->entry[i].busid) == 0)
+			continue;
+		if (copy->entry[i].device) {
+			dasd_put_device(copy->entry[i].device);
+			copy->entry[i].device->copy = NULL;
+			copy->entry[i].device = NULL;
+		}
+		devmap = dasd_find_busid_locked(copy->entry[i].busid);
+		devmap->copy = NULL;
+		memset(copy->entry[i].busid, 0, DASD_BUS_ID_SIZE);
+	}
+	kfree(copy);
+	rc = 0;
+out:
+	spin_unlock(&dasd_devmap_lock);
+	return rc;
+}
+
+/*
+ * parse BUSIDs from a copy pair
+ */
+static int dasd_devmap_parse_busid(const char *buf, char *prim_busid,
+				   char *sec_busid)
+{
+	char *primary, *secondary, *tmp, *pt;
+	int id0, id1, id2;
+
+	pt =  kstrdup(buf, GFP_KERNEL);
+	tmp = pt;
+	if (!tmp)
+		return -ENOMEM;
+
+	primary = strsep(&tmp, ",");
+	if (!primary) {
+		kfree(pt);
+		return -EINVAL;
+	}
+	secondary = strsep(&tmp, ",");
+	if (!secondary) {
+		kfree(pt);
+		return -EINVAL;
+	}
+	if (dasd_busid(primary, &id0, &id1, &id2)) {
+		kfree(pt);
+		return -EINVAL;
+	}
+	sprintf(prim_busid, "%01x.%01x.%04x", id0, id1, id2);
+	if (dasd_busid(secondary, &id0, &id1, &id2)) {
+		kfree(pt);
+		return -EINVAL;
+	}
+	sprintf(sec_busid, "%01x.%01x.%04x", id0, id1, id2);
+	kfree(pt);
+
+	return 0;
+}
+
+static ssize_t dasd_copy_pair_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	struct dasd_devmap *prim_devmap, *sec_devmap;
+	char prim_busid[DASD_BUS_ID_SIZE];
+	char sec_busid[DASD_BUS_ID_SIZE];
+	struct dasd_copy_relation *copy;
+	struct dasd_device *device;
+	bool pprc_enabled;
+	int rc;
+
+	if (strncmp(buf, "clear", strlen("clear")) == 0) {
+		if (dasd_devmap_clear_copy_relation(dev))
+			return -EINVAL;
+		return count;
+	}
+
+	rc = dasd_devmap_parse_busid(buf, prim_busid, sec_busid);
+	if (rc)
+		return rc;
+
+	if (strncmp(dev_name(dev), prim_busid, DASD_BUS_ID_SIZE) != 0 &&
+	    strncmp(dev_name(dev), sec_busid, DASD_BUS_ID_SIZE) != 0)
+		return -EINVAL;
+
+	/* allocate primary devmap if needed */
+	prim_devmap = dasd_find_busid(prim_busid);
+	if (IS_ERR(prim_devmap))
+		prim_devmap = dasd_add_busid(prim_busid, DASD_FEATURE_DEFAULT);
+
+	/* allocate secondary devmap if needed */
+	sec_devmap = dasd_find_busid(sec_busid);
+	if (IS_ERR(sec_devmap))
+		sec_devmap = dasd_add_busid(sec_busid, DASD_FEATURE_DEFAULT);
+
+	/* setting copy relation is only allowed for offline secondary */
+	if (sec_devmap->device)
+		return -EINVAL;
+
+	if (prim_devmap->copy) {
+		copy = prim_devmap->copy;
+	} else if (sec_devmap->copy) {
+		copy = sec_devmap->copy;
+	} else {
+		copy = kzalloc(sizeof(*copy), GFP_KERNEL);
+		if (!copy)
+			return -ENOMEM;
+	}
+	spin_lock(&dasd_devmap_lock);
+	rc = dasd_devmap_set_copy_relation(prim_devmap, copy, prim_busid, true);
+	if (rc) {
+		spin_unlock(&dasd_devmap_lock);
+		return rc;
+	}
+	rc = dasd_devmap_set_copy_relation(sec_devmap, copy, sec_busid, false);
+	if (rc) {
+		spin_unlock(&dasd_devmap_lock);
+		return rc;
+	}
+	spin_unlock(&dasd_devmap_lock);
+
+	/* if primary device is already online call device setup directly */
+	if (prim_devmap->device && !prim_devmap->device->copy) {
+		device = prim_devmap->device;
+		if (device->discipline->pprc_enabled) {
+			pprc_enabled = device->discipline->pprc_enabled(device);
+			rc = dasd_devmap_set_device_copy_relation(device->cdev,
+								  pprc_enabled);
+		} else {
+			rc = -EOPNOTSUPP;
+		}
+	}
+	if (rc) {
+		dasd_devmap_del_copy_relation(copy, prim_busid);
+		dasd_devmap_del_copy_relation(copy, sec_busid);
+		count = rc;
+	}
+
+	return count;
+}
+static DEVICE_ATTR(copy_pair, 0644, dasd_copy_pair_show,
+		   dasd_copy_pair_store);
+
+static ssize_t
+dasd_copy_role_show(struct device *dev,
+		    struct device_attribute *attr, char *buf)
+{
+	struct dasd_copy_relation *copy;
+	struct dasd_device *device;
+	int len, i;
+
+	device = dasd_device_from_cdev(to_ccwdev(dev));
+	if (IS_ERR(device))
+		return -ENODEV;
+
+	if (!device->copy) {
+		len = sysfs_emit(buf, "none\n");
+		goto out;
+	}
+	copy = device->copy;
+	/* only the active device is primary */
+	if (copy->active->device == device) {
+		len = sysfs_emit(buf, "primary\n");
+		goto out;
+	}
+	for (i = 0; i < DASD_CP_ENTRIES; i++) {
+		if (copy->entry[i].device == device) {
+			len = sysfs_emit(buf, "secondary\n");
+			goto out;
+		}
+	}
+	/* not in the list, no COPY role */
+	len = sysfs_emit(buf, "none\n");
+out:
+	dasd_put_device(device);
+	return len;
+}
+static DEVICE_ATTR(copy_role, 0444, dasd_copy_role_show, NULL);
+
 #define DASD_DEFINE_ATTR(_name, _func)					\
 static ssize_t dasd_##_name##_show(struct device *dev,			\
 				   struct device_attribute *attr,	\
@@ -1739,6 +2289,8 @@
 	&dev_attr_hpf.attr,
 	&dev_attr_ese.attr,
 	&dev_attr_fc_security.attr,
+	&dev_attr_copy_pair.attr,
+	&dev_attr_copy_role.attr,
 	NULL,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_eckd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_eckd.c
@@ -2029,6 +2029,49 @@
 }
 
 /*
+ * return if the device is the copy relation primary if a copy relation is active
+ */
+static int dasd_device_is_primary(struct dasd_device *device)
+{
+	if (!device->copy)
+		return 1;
+
+	if (device->copy->active->device == device)
+		return 1;
+
+	return 0;
+}
+
+static int dasd_eckd_alloc_block(struct dasd_device *device)
+{
+	struct dasd_block *block;
+	struct dasd_uid temp_uid;
+
+	if (!dasd_device_is_primary(device))
+		return 0;
+
+	dasd_eckd_get_uid(device, &temp_uid);
+	if (temp_uid.type == UA_BASE_DEVICE) {
+		block = dasd_alloc_block();
+		if (IS_ERR(block)) {
+			DBF_EVENT_DEVID(DBF_WARNING, device->cdev, "%s",
+					"could not allocate dasd block structure");
+			return PTR_ERR(block);
+		}
+		device->block = block;
+		block->base = device;
+	}
+	return 0;
+}
+
+static bool dasd_eckd_pprc_enabled(struct dasd_device *device)
+{
+	struct dasd_eckd_private *private = device->private;
+
+	return private->rdc_data.facilities.PPRC_enabled;
+}
+
+/*
  * Check device characteristics.
  * If the device is accessible using ECKD discipline, the device is enabled.
  */
@@ -2036,8 +2079,6 @@
 dasd_eckd_check_characteristics(struct dasd_device *device)
 {
 	struct dasd_eckd_private *private = device->private;
-	struct dasd_block *block;
-	struct dasd_uid temp_uid;
 	int rc, i;
 	int readonly;
 	unsigned long value;
@@ -2095,20 +2136,29 @@
 			device->default_expires = value;
 	}
 
-	dasd_eckd_get_uid(device, &temp_uid);
-	if (temp_uid.type == UA_BASE_DEVICE) {
-		block = dasd_alloc_block();
-		if (IS_ERR(block)) {
-			DBF_EVENT_DEVID(DBF_WARNING, device->cdev, "%s",
-					"could not allocate dasd "
-					"block structure");
-			rc = PTR_ERR(block);
-			goto out_err1;
-		}
-		device->block = block;
-		block->base = device;
+	/* Read Device Characteristics */
+	rc = dasd_generic_read_dev_chars(device, DASD_ECKD_MAGIC,
+					 &private->rdc_data, 64);
+	if (rc) {
+		DBF_EVENT_DEVID(DBF_WARNING, device->cdev,
+				"Read device characteristic failed, rc=%d", rc);
+		goto out_err1;
 	}
 
+	/* setup PPRC for device from devmap */
+	rc = dasd_devmap_set_device_copy_relation(device->cdev,
+						  dasd_eckd_pprc_enabled(device));
+	if (rc) {
+		DBF_EVENT_DEVID(DBF_WARNING, device->cdev,
+				"copy relation setup failed, rc=%d", rc);
+		goto out_err1;
+	}
+
+	/* check if block device is needed and allocate in case */
+	rc = dasd_eckd_alloc_block(device);
+	if (rc)
+		goto out_err1;
+
 	/* register lcu with alias handling, enable PAV */
 	rc = dasd_alias_make_device_known_to_lcu(device);
 	if (rc)
@@ -2132,15 +2182,6 @@
 	/* Read Extent Pool Information */
 	dasd_eckd_read_ext_pool_info(device);
 
-	/* Read Device Characteristics */
-	rc = dasd_generic_read_dev_chars(device, DASD_ECKD_MAGIC,
-					 &private->rdc_data, 64);
-	if (rc) {
-		DBF_EVENT_DEVID(DBF_WARNING, device->cdev,
-				"Read device characteristic failed, rc=%d", rc);
-		goto out_err3;
-	}
-
 	if ((device->features & DASD_FEATURE_USERAW) &&
 	    !(private->rdc_data.facilities.RT_in_LR)) {
 		dev_err(&device->cdev->dev, "The storage server does not "
@@ -2260,6 +2301,7 @@
 	cqr->status = DASD_CQR_FILLED;
 	/* Set flags to suppress output for expected errors */
 	set_bit(DASD_CQR_SUPPRESS_NRF, &cqr->flags);
+	set_bit(DASD_CQR_SUPPRESS_IT, &cqr->flags);
 
 	return cqr;
 }
@@ -2541,7 +2583,6 @@
 	cqr->buildclk = get_tod_clock();
 	cqr->status = DASD_CQR_FILLED;
 	/* Set flags to suppress output for expected errors */
-	set_bit(DASD_CQR_SUPPRESS_FP, &cqr->flags);
 	set_bit(DASD_CQR_SUPPRESS_IL, &cqr->flags);
 
 	return cqr;
@@ -3095,13 +3136,24 @@
 }
 
 static bool test_and_set_format_track(struct dasd_format_entry *to_format,
-				      struct dasd_block *block)
+				      struct dasd_ccw_req *cqr)
 {
+	struct dasd_block *block = cqr->block;
 	struct dasd_format_entry *format;
 	unsigned long flags;
 	bool rc = false;
 
 	spin_lock_irqsave(&block->format_lock, flags);
+	if (cqr->trkcount != atomic_read(&block->trkcount)) {
+		/*
+		 * The number of formatted tracks has changed after request
+		 * start and we can not tell if the current track was involved.
+		 * To avoid data corruption treat it as if the current track is
+		 * involved
+		 */
+		rc = true;
+		goto out;
+	}
 	list_for_each_entry(format, &block->format_list, list) {
 		if (format->track == to_format->track) {
 			rc = true;
@@ -3121,6 +3173,7 @@
 	unsigned long flags;
 
 	spin_lock_irqsave(&block->format_lock, flags);
+	atomic_inc(&block->trkcount);
 	list_del_init(&format->list);
 	spin_unlock_irqrestore(&block->format_lock, flags);
 }
@@ -3157,7 +3210,7 @@
 	sector_t curr_trk;
 	int rc;
 
-	req = cqr->callback_data;
+	req = dasd_get_callback_data(cqr);
 	block = cqr->block;
 	base = block->base;
 	private = base->private;
@@ -3182,8 +3235,11 @@
 	}
 	format->track = curr_trk;
 	/* test if track is already in formatting by another thread */
-	if (test_and_set_format_track(format, block))
+	if (test_and_set_format_track(format, cqr)) {
+		/* this is no real error so do not count down retries */
+		cqr->retries++;
 		return ERR_PTR(-EEXIST);
+	}
 
 	fdata.start_unit = curr_trk;
 	fdata.stop_unit = curr_trk;
@@ -3282,12 +3338,11 @@
 				cqr->proc_bytes = blk_count * blksize;
 				return 0;
 			}
-			if (dst && !skip_block) {
-				dst += off;
+			if (dst && !skip_block)
 				memset(dst, 0, blksize);
-			} else {
+			else
 				skip_block--;
-			}
+			dst += blksize;
 			blk_count++;
 		}
 	}
@@ -4076,8 +4131,6 @@
 
 	/* Set flags to suppress output for expected errors */
 	if (dasd_eckd_is_ese(basedev)) {
-		set_bit(DASD_CQR_SUPPRESS_FP, &cqr->flags);
-		set_bit(DASD_CQR_SUPPRESS_IL, &cqr->flags);
 		set_bit(DASD_CQR_SUPPRESS_NRF, &cqr->flags);
 	}
 
@@ -4579,9 +4632,8 @@
 
 	/* Set flags to suppress output for expected errors */
 	if (dasd_eckd_is_ese(basedev)) {
-		set_bit(DASD_CQR_SUPPRESS_FP, &cqr->flags);
-		set_bit(DASD_CQR_SUPPRESS_IL, &cqr->flags);
 		set_bit(DASD_CQR_SUPPRESS_NRF, &cqr->flags);
+		set_bit(DASD_CQR_SUPPRESS_IT, &cqr->flags);
 	}
 
 	return cqr;
@@ -4682,7 +4734,6 @@
 	struct dasd_device *basedev;
 	struct req_iterator iter;
 	struct dasd_ccw_req *cqr;
-	unsigned int first_offs;
 	unsigned int trkcount;
 	unsigned long *idaws;
 	unsigned int size;
@@ -4716,7 +4767,6 @@
 	last_trk = (blk_rq_pos(req) + blk_rq_sectors(req) - 1) /
 		DASD_RAW_SECTORS_PER_TRACK;
 	trkcount = last_trk - first_trk + 1;
-	first_offs = 0;
 
 	if (rq_data_dir(req) == READ)
 		cmd = DASD_ECKD_CCW_READ_TRACK;
@@ -4760,13 +4810,13 @@
 
 	if (use_prefix) {
 		prefix_LRE(ccw++, data, first_trk, last_trk, cmd, basedev,
-			   startdev, 1, first_offs + 1, trkcount, 0, 0);
+			   startdev, 1, 0, trkcount, 0, 0);
 	} else {
 		define_extent(ccw++, data, first_trk, last_trk, cmd, basedev, 0);
 		ccw[-1].flags |= CCW_FLAG_CC;
 
 		data += sizeof(struct DE_eckd_data);
-		locate_record_ext(ccw++, data, first_trk, first_offs + 1,
+		locate_record_ext(ccw++, data, first_trk, 0,
 				  trkcount, cmd, basedev, 0, 0);
 	}
 
@@ -5753,36 +5803,32 @@
 {
 	u8 *sense = dasd_get_sense(irb);
 
-	if (scsw_is_tm(&irb->scsw)) {
-		/*
-		 * In some cases the 'File Protected' or 'Incorrect Length'
-		 * error might be expected and log messages shouldn't be written
-		 * then. Check if the according suppress bit is set.
-		 */
-		if (sense && (sense[1] & SNS1_FILE_PROTECTED) &&
-		    test_bit(DASD_CQR_SUPPRESS_FP, &req->flags))
-			return;
-		if (scsw_cstat(&irb->scsw) == 0x40 &&
-		    test_bit(DASD_CQR_SUPPRESS_IL, &req->flags))
-			return;
+	/*
+	 * In some cases certain errors might be expected and
+	 * log messages shouldn't be written then.
+	 * Check if the according suppress bit is set.
+	 */
+	if (sense && (sense[1] & SNS1_INV_TRACK_FORMAT) &&
+	    !(sense[2] & SNS2_ENV_DATA_PRESENT) &&
+	    test_bit(DASD_CQR_SUPPRESS_IT, &req->flags))
+		return;
 
-		dasd_eckd_dump_sense_tcw(device, req, irb);
-	} else {
-		/*
-		 * In some cases the 'Command Reject' or 'No Record Found'
-		 * error might be expected and log messages shouldn't be
-		 * written then. Check if the according suppress bit is set.
-		 */
-		if (sense && sense[0] & SNS0_CMD_REJECT &&
-		    test_bit(DASD_CQR_SUPPRESS_CR, &req->flags))
-			return;
+	if (sense && sense[0] & SNS0_CMD_REJECT &&
+	    test_bit(DASD_CQR_SUPPRESS_CR, &req->flags))
+		return;
 
-		if (sense && sense[1] & SNS1_NO_REC_FOUND &&
-		    test_bit(DASD_CQR_SUPPRESS_NRF, &req->flags))
-			return;
+	if (sense && sense[1] & SNS1_NO_REC_FOUND &&
+	    test_bit(DASD_CQR_SUPPRESS_NRF, &req->flags))
+		return;
+
+	if (scsw_cstat(&irb->scsw) == 0x40 &&
+	    test_bit(DASD_CQR_SUPPRESS_IL, &req->flags))
+		return;
 
+	if (scsw_is_tm(&irb->scsw))
+		dasd_eckd_dump_sense_tcw(device, req, irb);
+	else
 		dasd_eckd_dump_sense_ccw(device, req, irb);
-	}
 }
 
 static int dasd_eckd_reload_device(struct dasd_device *device)
@@ -6086,6 +6132,71 @@
 }
 
 /*
+ * Perform Subsystem Function - Peer-to-Peer Remote Copy Extended Query
+ */
+static int dasd_eckd_query_pprc_status(struct dasd_device *device,
+				       struct dasd_pprc_data_sc4 *data)
+{
+	struct dasd_pprc_data_sc4 *pprc_data;
+	struct dasd_psf_prssd_data *prssdp;
+	struct dasd_ccw_req *cqr;
+	struct ccw1 *ccw;
+	int rc;
+
+	cqr = dasd_smalloc_request(DASD_ECKD_MAGIC, 1 /* PSF */	+ 1 /* RSSD */,
+				   sizeof(*prssdp) + sizeof(*pprc_data) + 1,
+				   device, NULL);
+	if (IS_ERR(cqr)) {
+		DBF_EVENT_DEVID(DBF_WARNING, device->cdev, "%s",
+				"Could not allocate query PPRC status request");
+		return PTR_ERR(cqr);
+	}
+	cqr->startdev = device;
+	cqr->memdev = device;
+	cqr->block = NULL;
+	cqr->retries = 256;
+	cqr->expires = 10 * HZ;
+
+	/* Prepare for Read Subsystem Data */
+	prssdp = (struct dasd_psf_prssd_data *)cqr->data;
+	memset(prssdp, 0, sizeof(struct dasd_psf_prssd_data));
+	prssdp->order = PSF_ORDER_PRSSD;
+	prssdp->suborder = PSF_SUBORDER_PPRCEQ;
+	prssdp->varies[0] = PPRCEQ_SCOPE_4;
+	pprc_data = (struct dasd_pprc_data_sc4 *)(prssdp + 1);
+
+	ccw = cqr->cpaddr;
+	ccw->cmd_code = DASD_ECKD_CCW_PSF;
+	ccw->count = sizeof(struct dasd_psf_prssd_data);
+	ccw->flags |= CCW_FLAG_CC;
+	ccw->flags |= CCW_FLAG_SLI;
+	ccw->cda = (__u32)(addr_t)prssdp;
+
+	/* Read Subsystem Data - query host access */
+	ccw++;
+	ccw->cmd_code = DASD_ECKD_CCW_RSSD;
+	ccw->count = sizeof(*pprc_data);
+	ccw->flags |= CCW_FLAG_SLI;
+	ccw->cda = (__u32)(addr_t)pprc_data;
+
+	cqr->buildclk = get_tod_clock();
+	cqr->status = DASD_CQR_FILLED;
+
+	rc = dasd_sleep_on_interruptible(cqr);
+	if (rc == 0) {
+		*data = *pprc_data;
+	} else {
+		DBF_EVENT_DEVID(DBF_WARNING, device->cdev,
+				"PPRC Extended Query failed with rc=%d\n",
+				rc);
+		rc = -EOPNOTSUPP;
+	}
+
+	dasd_sfree_request(cqr, cqr->memdev);
+	return rc;
+}
+
+/*
  * Perform Subsystem Function - CUIR response
  */
 static int
@@ -6703,6 +6814,8 @@
 	.ext_pool_exhaust = dasd_eckd_ext_pool_exhaust,
 	.ese_format = dasd_eckd_ese_format,
 	.ese_read = dasd_eckd_ese_read,
+	.pprc_status = dasd_eckd_query_pprc_status,
+	.pprc_enabled = dasd_eckd_pprc_enabled,
 };
 
 static int __init
@@ -6717,8 +6830,10 @@
 		return -ENOMEM;
 	dasd_vol_info_req = kmalloc(sizeof(*dasd_vol_info_req),
 				    GFP_KERNEL | GFP_DMA);
-	if (!dasd_vol_info_req)
+	if (!dasd_vol_info_req) {
+		kfree(dasd_reserve_req);
 		return -ENOMEM;
+	}
 	pe_handler_worker = kmalloc(sizeof(*pe_handler_worker),
 				    GFP_KERNEL | GFP_DMA);
 	if (!pe_handler_worker) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_eckd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_eckd.h
@@ -66,10 +66,16 @@
  * Perform Subsystem Function / Sub-Orders
  */
 #define PSF_SUBORDER_QHA		 0x1C /* Query Host Access */
+#define PSF_SUBORDER_PPRCEQ		 0x50 /* PPRC Extended Query */
 #define PSF_SUBORDER_VSQ		 0x52 /* Volume Storage Query */
 #define PSF_SUBORDER_LCQ		 0x53 /* Logical Configuration Query */
 
 /*
+ * PPRC Extended Query Scopes
+ */
+#define PPRCEQ_SCOPE_4			 0x04 /* Scope 4 for PPRC Extended Query */
+
+/*
  * CUIR response condition codes
  */
 #define PSF_CUIR_INVALID		 0x00
@@ -261,7 +267,7 @@
 		unsigned char reserved3:8;
 		unsigned char defect_wr:1;
 		unsigned char XRC_supported:1;
-		unsigned char reserved4:1;
+		unsigned char PPRC_enabled:1;
 		unsigned char striping:1;
 		unsigned char reserved5:4;
 		unsigned char cfw:1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_eer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_eer.c
@@ -387,6 +387,7 @@
 		break;
 	case DASD_EER_NOPATH:
 	case DASD_EER_NOSPC:
+	case DASD_EER_AUTOQUIESCE:
 		dasd_eer_write_standard_trigger(device, NULL, id);
 		break;
 	case DASD_EER_STATECHANGE:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_genhd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_genhd.c
@@ -14,6 +14,7 @@
 #define KMSG_COMPONENT "dasd"
 
 #include <linux/interrupt.h>
+#include <linux/major.h>
 #include <linux/fs.h>
 #include <linux/blkpg.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_int.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_int.h
@@ -188,6 +188,7 @@
 	void (*callback)(struct dasd_ccw_req *, void *data);
 	void *callback_data;
 	unsigned int proc_bytes;	/* bytes for partial completion */
+	unsigned int trkcount;		/* count formatted tracks */
 };
 
 /*
@@ -225,7 +226,7 @@
  * The following flags are used to suppress output of certain errors.
  */
 #define DASD_CQR_SUPPRESS_NRF	4	/* Suppress 'No Record Found' error */
-#define DASD_CQR_SUPPRESS_FP	5	/* Suppress 'File Protected' error*/
+#define DASD_CQR_SUPPRESS_IT	5	/* Suppress 'Invalid Track' error*/
 #define DASD_CQR_SUPPRESS_IL	6	/* Suppress 'Incorrect Length' error */
 #define DASD_CQR_SUPPRESS_CR	7	/* Suppress 'Command Reject' error */
 
@@ -260,6 +261,55 @@
 };
 
 /*
+ * PPRC Status data
+ */
+struct dasd_pprc_header {
+	__u8 entries;		/* 0     Number of device entries */
+	__u8 unused;		/* 1     unused */
+	__u16 entry_length;	/* 2-3   Length of device entry */
+	__u32 unused2;		/* 4-7   unused */
+} __packed;
+
+struct dasd_pprc_dev_info {
+	__u8 state;		/* 0       Copy State */
+	__u8 flags;		/* 1       Flags */
+	__u8 reserved1[2];	/* 2-3     reserved */
+	__u8 prim_lss;		/* 4       Primary device LSS */
+	__u8 primary;		/* 5       Primary device address */
+	__u8 sec_lss;		/* 6       Secondary device LSS */
+	__u8 secondary;		/* 7       Secondary device address */
+	__u16 pprc_id;		/* 8-9     Peer-to-Peer Remote Copy ID */
+	__u8 reserved2[12];	/* 10-21   reserved */
+	__u16 prim_cu_ssid;	/* 22-23   Pimary Control Unit SSID */
+	__u8 reserved3[12];	/* 24-35   reserved */
+	__u16 sec_cu_ssid;	/* 36-37   Secondary Control Unit SSID */
+	__u8 reserved4[90];	/* 38-127  reserved */
+} __packed;
+
+struct dasd_pprc_data_sc4 {
+	struct dasd_pprc_header header;
+	struct dasd_pprc_dev_info dev_info[5];
+} __packed;
+
+#define DASD_BUS_ID_SIZE 20
+#define DASD_CP_ENTRIES 5
+
+struct dasd_copy_entry {
+	char busid[DASD_BUS_ID_SIZE];
+	struct dasd_device *device;
+	bool primary;
+	bool configured;
+};
+
+struct dasd_copy_relation {
+	struct dasd_copy_entry entry[DASD_CP_ENTRIES];
+	struct dasd_copy_entry *active;
+};
+
+int dasd_devmap_set_device_copy_relation(struct ccw_device *,
+					 bool pprc_enabled);
+
+/*
  * the struct dasd_discipline is
  * sth like a table of virtual functions, if you think of dasd_eckd
  * inheriting dasd...
@@ -387,6 +437,8 @@
 	struct dasd_ccw_req *(*ese_format)(struct dasd_device *,
 					   struct dasd_ccw_req *, struct irb *);
 	int (*ese_read)(struct dasd_ccw_req *, struct irb *);
+	int (*pprc_status)(struct dasd_device *, struct	dasd_pprc_data_sc4 *);
+	bool (*pprc_enabled)(struct dasd_device *);
 };
 
 extern struct dasd_discipline *dasd_diag_discipline_pointer;
@@ -407,6 +459,7 @@
 #define DASD_EER_STATECHANGE 3
 #define DASD_EER_PPRCSUSPEND 4
 #define DASD_EER_NOSPC	     5
+#define DASD_EER_AUTOQUIESCE 31
 
 /* DASD path handling */
 
@@ -583,6 +636,8 @@
 	struct dasd_profile profile;
 	struct dasd_format_entry format_entry;
 	struct kset *paths_info;
+	struct dasd_copy_relation *copy;
+	unsigned long aq_mask;
 };
 
 struct dasd_block {
@@ -611,6 +666,7 @@
 
 	struct list_head format_list;
 	spinlock_t format_lock;
+	atomic_t trkcount;
 };
 
 struct dasd_attention_data {
@@ -757,6 +813,18 @@
 	return 0;
 }
 
+/*
+ * return the callback data of the original request in case there are
+ * ERP requests build on top of it
+ */
+static inline void *dasd_get_callback_data(struct dasd_ccw_req *cqr)
+{
+	while (cqr->refers)
+		cqr = cqr->refers;
+
+	return cqr->callback_data;
+}
+
 /* externals in dasd.c */
 #define DASD_PROFILE_OFF	 0
 #define DASD_PROFILE_ON 	 1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dasd_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dasd_ioctl.c
@@ -131,6 +131,7 @@
 	spin_unlock_irqrestore(get_ccwdev_lock(base->cdev), flags);
 
 	dasd_schedule_block_bh(block);
+	dasd_schedule_device_bh(base);
 	return 0;
 }
 
@@ -502,10 +503,10 @@
 
 	memcpy(dasd_info->type, base->discipline->name, 4);
 
-	spin_lock_irqsave(&block->queue_lock, flags);
+	spin_lock_irqsave(get_ccwdev_lock(base->cdev), flags);
 	list_for_each(l, &base->ccw_queue)
 		dasd_info->chanq_len++;
-	spin_unlock_irqrestore(&block->queue_lock, flags);
+	spin_unlock_irqrestore(get_ccwdev_lock(base->cdev), flags);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/dcssblk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/dcssblk.c
@@ -866,6 +866,8 @@
 	unsigned long bytes_done;
 
 	blk_queue_split(&bio);
+	if (!bio)
+		return BLK_QC_T_NONE;
 
 	bytes_done = 0;
 	dev_info = bio->bi_bdev->bd_disk->private_data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/block/scm_blk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/block/scm_blk.c
@@ -18,6 +18,7 @@
 #include <linux/genhd.h>
 #include <linux/slab.h>
 #include <linux/list.h>
+#include <linux/io.h>
 #include <asm/eadm.h>
 #include "scm_blk.h"
 
@@ -131,7 +132,7 @@
 
 	for (i = 0; i < nr_requests_per_io && scmrq->request[i]; i++) {
 		msb = &scmrq->aob->msb[i];
-		aidaw = msb->data_addr;
+		aidaw = (u64)phys_to_virt(msb->data_addr);
 
 		if ((msb->flags & MSB_FLAG_IDA) && aidaw &&
 		    IS_ALIGNED(aidaw, PAGE_SIZE))
@@ -196,12 +197,12 @@
 	msb->scm_addr = scmdev->address + ((u64) blk_rq_pos(req) << 9);
 	msb->oc = (rq_data_dir(req) == READ) ? MSB_OC_READ : MSB_OC_WRITE;
 	msb->flags |= MSB_FLAG_IDA;
-	msb->data_addr = (u64) aidaw;
+	msb->data_addr = (u64)virt_to_phys(aidaw);
 
 	rq_for_each_segment(bv, req, iter) {
 		WARN_ON(bv.bv_offset);
 		msb->blk_count += bv.bv_len >> 12;
-		aidaw->data_addr = (u64) page_address(bv.bv_page);
+		aidaw->data_addr = virt_to_phys(page_address(bv.bv_page));
 		aidaw++;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/Kconfig
@@ -100,6 +100,17 @@
 	  This option enables the Open-for-Business interface to the s390
 	  Service Element.
 
+config S390_UV_UAPI
+	def_tristate m
+	prompt "Ultravisor userspace API"
+	depends on S390
+	help
+	  Selecting exposes parts of the UV interface to userspace
+	  by providing a misc character device at /dev/uv.
+	  Using IOCTLs one can interact with the UV.
+	  The device is only available if the Ultravisor
+	  Facility (158) is present.
+
 config S390_TAPE
 	def_tristate m
 	prompt "S/390 tape device support"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/Makefile
@@ -48,6 +48,7 @@
 obj-$(CONFIG_MONWRITER) += monwriter.o
 obj-$(CONFIG_S390_VMUR) += vmur.o
 obj-$(CONFIG_CRASH_DUMP) += sclp_sdias.o zcore.o
+obj-$(CONFIG_S390_UV_UAPI) += uvdevice.o
 
 hmcdrv-objs := hmcdrv_mod.o hmcdrv_dev.o hmcdrv_ftp.o hmcdrv_cache.o diag_ftp.o sclp_ftp.o
 obj-$(CONFIG_HMC_DRV) += hmcdrv.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/keyboard.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/keyboard.h
@@ -56,7 +56,7 @@
 kbd_put_queue(struct tty_port *port, int ch)
 {
 	tty_insert_flip_char(port, ch, 0);
-	tty_schedule_flip(port);
+	tty_flip_buffer_push(port);
 }
 
 static inline void
@@ -64,5 +64,5 @@
 {
 	while (*cp)
 		tty_insert_flip_char(port, *cp++, 0);
-	tty_schedule_flip(port);
+	tty_flip_buffer_push(port);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/sclp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/sclp.c
@@ -1292,6 +1292,7 @@
 fail_unregister_reboot_notifier:
 	unregister_reboot_notifier(&sclp_reboot_notifier);
 fail_init_state_uninitialized:
+	list_del(&sclp_state_change_event.list);
 	sclp_init_state = sclp_init_state_uninitialized;
 	free_page((unsigned long) sclp_read_sccb);
 	free_page((unsigned long) sclp_init_sccb);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/sclp_early.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/sclp_early.c
@@ -45,12 +45,18 @@
 	sclp.has_gisaf = !!(sccb->fac118 & 0x08);
 	sclp.has_hvs = !!(sccb->fac119 & 0x80);
 	sclp.has_kss = !!(sccb->fac98 & 0x01);
+	sclp.has_aisii = !!(sccb->fac118 & 0x40);
+	sclp.has_aeni = !!(sccb->fac118 & 0x20);
+	sclp.has_aisi = !!(sccb->fac118 & 0x10);
+	sclp.has_zpci_lsi = !!(sccb->fac118 & 0x01);
 	if (sccb->fac85 & 0x02)
 		S390_lowcore.machine_flags |= MACHINE_FLAG_ESOP;
 	if (sccb->fac91 & 0x40)
 		S390_lowcore.machine_flags |= MACHINE_FLAG_TLB_GUEST;
-	if (sccb->cpuoff > 134)
+	if (sccb->cpuoff > 134) {
 		sclp.has_diag318 = !!(sccb->byte_134 & 0x80);
+		sclp.has_iplcc = !!(sccb->byte_134 & 0x02);
+	}
 	if (sccb->cpuoff > 137)
 		sclp.has_sipl = !!(sccb->cbl & 0x4000);
 	sclp.rnmax = sccb->rnmax ? sccb->rnmax : sccb->rnmax2;
@@ -139,7 +145,7 @@
 	}
 	sclp_fill_core_info(info, sccb);
 out:
-	memblock_free_early((unsigned long)sccb, length);
+	memblock_free((unsigned long)sccb, length);
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/sclp_sd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/sclp_sd.c
@@ -319,8 +319,14 @@
 			  &esize);
 	if (rc) {
 		/* Cancel running request if interrupted */
-		if (rc == -ERESTARTSYS)
-			sclp_sd_sync(page, SD_EQ_HALT, di, 0, 0, NULL, NULL);
+		if (rc == -ERESTARTSYS) {
+			if (sclp_sd_sync(page, SD_EQ_HALT, di, 0, 0, NULL, NULL)) {
+				pr_warn("Could not stop Store Data request - leaking at least %zu bytes\n",
+					(size_t)dsize * PAGE_SIZE);
+				data = NULL;
+				asce = 0;
+			}
+		}
 		vfree(data);
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/sclp_vt220.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/sclp_vt220.c
@@ -320,7 +320,7 @@
 	buffer = (void *) ((addr_t) sccb + sccb->header.length);
 
 	if (convertlf) {
-		/* Perform Linefeed conversion (0x0a -> 0x0a 0x0d)*/
+		/* Perform Linefeed conversion (0x0a -> 0x0d 0x0a)*/
 		for (from=0, to=0;
 		     (from < count) && (to < sclp_vt220_space_left(request));
 		     from++) {
@@ -329,8 +329,8 @@
 			/* Perform conversion */
 			if (c == 0x0a) {
 				if (to + 1 < sclp_vt220_space_left(request)) {
-					((unsigned char *) buffer)[to++] = c;
 					((unsigned char *) buffer)[to++] = 0x0d;
+					((unsigned char *) buffer)[to++] = c;
 				} else
 					break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/tape_std.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/tape_std.c
@@ -53,7 +53,6 @@
 tape_std_assign(struct tape_device *device)
 {
 	int                  rc;
-	struct timer_list    timeout;
 	struct tape_request *request;
 
 	request = tape_alloc_request(2, 11);
@@ -70,7 +69,7 @@
 	 * So we set up a timeout for this call.
 	 */
 	timer_setup(&request->timer, tape_std_assign_timeout, 0);
-	mod_timer(&timeout, jiffies + 2 * HZ);
+	mod_timer(&request->timer, jiffies + msecs_to_jiffies(2000));
 
 	rc = tape_do_io_interruptible(device, request);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/uvdevice.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/uvdevice.c
@@ -0,0 +1,257 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Copyright IBM Corp. 2022
+ *  Author(s): Steffen Eiden <seiden@linux.ibm.com>
+ *
+ *  This file provides a Linux misc device to give userspace access to some
+ *  Ultravisor (UV) functions. The device only accepts IOCTLs and will only
+ *  be present if the Ultravisor facility (158) is present.
+ *
+ *  When userspace sends a valid IOCTL uvdevice will copy the input data to
+ *  kernel space, do some basic validity checks to avoid kernel/system
+ *  corruption. Any other check that the Ultravisor does will not be done by
+ *  the uvdevice to keep changes minimal when adding new functionalities
+ *  to existing UV-calls.
+ *  After the checks uvdevice builds a corresponding
+ *  Ultravisor Call Control Block, and sends the request to the Ultravisor.
+ *  Then, it copies the response, including the return codes, back to userspace.
+ *  It is the responsibility of the userspace to check for any error issued
+ *  by UV and to interpret the UV response. The uvdevice acts as a communication
+ *  channel for userspace to the Ultravisor.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/miscdevice.h>
+#include <linux/types.h>
+#include <linux/stddef.h>
+#include <linux/vmalloc.h>
+#include <linux/slab.h>
+
+#include <asm/uvdevice.h>
+#include <asm/uv.h>
+
+static int uvio_build_uvcb_attest(struct uv_cb_attest *uvcb_attest, u8 *arcb,
+				  u8 *meas, u8 *add_data, struct uvio_attest *uvio_attest)
+{
+	void __user *user_buf_arcb = (void __user *)uvio_attest->arcb_addr;
+
+	if (copy_from_user(arcb, user_buf_arcb, uvio_attest->arcb_len))
+		return -EFAULT;
+
+	uvcb_attest->header.len = sizeof(*uvcb_attest);
+	uvcb_attest->header.cmd = UVC_CMD_RETR_ATTEST;
+	uvcb_attest->arcb_addr = (u64)arcb;
+	uvcb_attest->cont_token = 0;
+	uvcb_attest->user_data_len = uvio_attest->user_data_len;
+	memcpy(uvcb_attest->user_data, uvio_attest->user_data, sizeof(uvcb_attest->user_data));
+	uvcb_attest->meas_len = uvio_attest->meas_len;
+	uvcb_attest->meas_addr = (u64)meas;
+	uvcb_attest->add_data_len = uvio_attest->add_data_len;
+	uvcb_attest->add_data_addr = (u64)add_data;
+
+	return 0;
+}
+
+static int uvio_copy_attest_result_to_user(struct uv_cb_attest *uvcb_attest,
+					   struct uvio_ioctl_cb *uv_ioctl,
+					   u8 *measurement, u8 *add_data,
+					   struct uvio_attest *uvio_attest)
+{
+	struct uvio_attest __user *user_uvio_attest = (void __user *)uv_ioctl->argument_addr;
+	void __user *user_buf_add = (void __user *)uvio_attest->add_data_addr;
+	void __user *user_buf_meas = (void __user *)uvio_attest->meas_addr;
+	void __user *user_buf_uid = &user_uvio_attest->config_uid;
+
+	if (copy_to_user(user_buf_meas, measurement, uvio_attest->meas_len))
+		return -EFAULT;
+	if (add_data && copy_to_user(user_buf_add, add_data, uvio_attest->add_data_len))
+		return -EFAULT;
+	if (copy_to_user(user_buf_uid, uvcb_attest->config_uid, sizeof(uvcb_attest->config_uid)))
+		return -EFAULT;
+	return 0;
+}
+
+static int get_uvio_attest(struct uvio_ioctl_cb *uv_ioctl, struct uvio_attest *uvio_attest)
+{
+	u8 __user *user_arg_buf = (u8 __user *)uv_ioctl->argument_addr;
+
+	if (copy_from_user(uvio_attest, user_arg_buf, sizeof(*uvio_attest)))
+		return -EFAULT;
+
+	if (uvio_attest->arcb_len > UVIO_ATT_ARCB_MAX_LEN)
+		return -EINVAL;
+	if (uvio_attest->arcb_len == 0)
+		return -EINVAL;
+	if (uvio_attest->meas_len > UVIO_ATT_MEASUREMENT_MAX_LEN)
+		return -EINVAL;
+	if (uvio_attest->meas_len == 0)
+		return -EINVAL;
+	if (uvio_attest->add_data_len > UVIO_ATT_ADDITIONAL_MAX_LEN)
+		return -EINVAL;
+	if (uvio_attest->reserved136)
+		return -EINVAL;
+	return 0;
+}
+
+/**
+ * uvio_attestation() - Perform a Retrieve Attestation Measurement UVC.
+ *
+ * @uv_ioctl: ioctl control block
+ *
+ * uvio_attestation() does a Retrieve Attestation Measurement Ultravisor Call.
+ * It verifies that the given userspace addresses are valid and request sizes
+ * are sane. Every other check is made by the Ultravisor (UV) and won't result
+ * in a negative return value. It copies the input to kernelspace, builds the
+ * request, sends the UV-call, and copies the result to userspace.
+ *
+ * The Attestation Request has two input and two outputs.
+ * ARCB and User Data are inputs for the UV generated by userspace.
+ * Measurement and Additional Data are outputs for userspace generated by UV.
+ *
+ * The Attestation Request Control Block (ARCB) is a cryptographically verified
+ * and secured request to UV and User Data is some plaintext data which is
+ * going to be included in the Attestation Measurement calculation.
+ *
+ * Measurement is a cryptographic measurement of the callers properties,
+ * optional data configured by the ARCB and the user data. If specified by the
+ * ARCB, UV will add some Additional Data to the measurement calculation.
+ * This Additional Data is then returned as well.
+ *
+ * If the Retrieve Attestation Measurement UV facility is not present,
+ * UV will return invalid command rc. This won't be fenced in the driver
+ * and does not result in a negative return value.
+ *
+ * Context: might sleep
+ *
+ * Return: 0 on success or a negative error code on error.
+ */
+static int uvio_attestation(struct uvio_ioctl_cb *uv_ioctl)
+{
+	struct uv_cb_attest *uvcb_attest = NULL;
+	struct uvio_attest *uvio_attest = NULL;
+	u8 *measurement = NULL;
+	u8 *add_data = NULL;
+	u8 *arcb = NULL;
+	int ret;
+
+	ret = -EINVAL;
+	if (uv_ioctl->argument_len != sizeof(*uvio_attest))
+		goto out;
+
+	ret = -ENOMEM;
+	uvio_attest = kzalloc(sizeof(*uvio_attest), GFP_KERNEL);
+	if (!uvio_attest)
+		goto out;
+
+	ret = get_uvio_attest(uv_ioctl, uvio_attest);
+	if (ret)
+		goto out;
+
+	ret = -ENOMEM;
+	arcb = kvzalloc(uvio_attest->arcb_len, GFP_KERNEL);
+	measurement = kvzalloc(uvio_attest->meas_len, GFP_KERNEL);
+	if (!arcb || !measurement)
+		goto out;
+
+	if (uvio_attest->add_data_len) {
+		add_data = kvzalloc(uvio_attest->add_data_len, GFP_KERNEL);
+		if (!add_data)
+			goto out;
+	}
+
+	uvcb_attest = kzalloc(sizeof(*uvcb_attest), GFP_KERNEL);
+	if (!uvcb_attest)
+		goto out;
+
+	ret = uvio_build_uvcb_attest(uvcb_attest, arcb,  measurement, add_data, uvio_attest);
+	if (ret)
+		goto out;
+
+	uv_call_sched(0, (u64)uvcb_attest);
+
+	uv_ioctl->uv_rc = uvcb_attest->header.rc;
+	uv_ioctl->uv_rrc = uvcb_attest->header.rrc;
+
+	ret = uvio_copy_attest_result_to_user(uvcb_attest, uv_ioctl, measurement, add_data,
+					      uvio_attest);
+out:
+	kvfree(arcb);
+	kvfree(measurement);
+	kvfree(add_data);
+	kfree(uvio_attest);
+	kfree(uvcb_attest);
+	return ret;
+}
+
+static int uvio_copy_and_check_ioctl(struct uvio_ioctl_cb *ioctl, void __user *argp)
+{
+	if (copy_from_user(ioctl, argp, sizeof(*ioctl)))
+		return -EFAULT;
+	if (ioctl->flags != 0)
+		return -EINVAL;
+	if (memchr_inv(ioctl->reserved14, 0, sizeof(ioctl->reserved14)))
+		return -EINVAL;
+
+	return 0;
+}
+
+/*
+ * IOCTL entry point for the Ultravisor device.
+ */
+static long uvio_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
+{
+	void __user *argp = (void __user *)arg;
+	struct uvio_ioctl_cb uv_ioctl = { };
+	long ret;
+
+	switch (cmd) {
+	case UVIO_IOCTL_ATT:
+		ret = uvio_copy_and_check_ioctl(&uv_ioctl, argp);
+		if (ret)
+			return ret;
+		ret = uvio_attestation(&uv_ioctl);
+		break;
+	default:
+		ret = -ENOIOCTLCMD;
+		break;
+	}
+	if (ret)
+		return ret;
+
+	if (copy_to_user(argp, &uv_ioctl, sizeof(uv_ioctl)))
+		ret = -EFAULT;
+
+	return ret;
+}
+
+static const struct file_operations uvio_dev_fops = {
+	.owner = THIS_MODULE,
+	.unlocked_ioctl = uvio_ioctl,
+	.llseek = no_llseek,
+};
+
+static struct miscdevice uvio_dev_miscdev = {
+	.minor = MISC_DYNAMIC_MINOR,
+	.name = UVIO_DEVICE_NAME,
+	.fops = &uvio_dev_fops,
+};
+
+static void __exit uvio_dev_exit(void)
+{
+	misc_deregister(&uvio_dev_miscdev);
+}
+
+static int __init uvio_dev_init(void)
+{
+	if (!test_facility(158))
+		return -ENXIO;
+	return misc_register(&uvio_dev_miscdev);
+}
+
+module_init(uvio_dev_init);
+module_exit(uvio_dev_exit);
+
+MODULE_AUTHOR("IBM Corporation");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Ultravisor UAPI driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/char/zcore.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/char/zcore.c
@@ -50,6 +50,7 @@
 static struct dentry *zcore_hsa_file;
 static struct ipl_parameter_block *zcore_ipl_block;
 
+static DEFINE_MUTEX(hsa_buf_mutex);
 static char hsa_buf[PAGE_SIZE] __aligned(PAGE_SIZE);
 
 /*
@@ -66,19 +67,24 @@
 	if (!hsa_available)
 		return -ENODATA;
 
+	mutex_lock(&hsa_buf_mutex);
 	while (count) {
 		if (sclp_sdias_copy(hsa_buf, src / PAGE_SIZE + 2, 1)) {
 			TRACE("sclp_sdias_copy() failed\n");
+			mutex_unlock(&hsa_buf_mutex);
 			return -EIO;
 		}
 		offset = src % PAGE_SIZE;
 		bytes = min(PAGE_SIZE - offset, count);
-		if (copy_to_user(dest, hsa_buf + offset, bytes))
+		if (copy_to_user(dest, hsa_buf + offset, bytes)) {
+			mutex_unlock(&hsa_buf_mutex);
 			return -EFAULT;
+		}
 		src += bytes;
 		dest += bytes;
 		count -= bytes;
 	}
+	mutex_unlock(&hsa_buf_mutex);
 	return 0;
 }
 
@@ -96,9 +102,11 @@
 	if (!hsa_available)
 		return -ENODATA;
 
+	mutex_lock(&hsa_buf_mutex);
 	while (count) {
 		if (sclp_sdias_copy(hsa_buf, src / PAGE_SIZE + 2, 1)) {
 			TRACE("sclp_sdias_copy() failed\n");
+			mutex_unlock(&hsa_buf_mutex);
 			return -EIO;
 		}
 		offset = src % PAGE_SIZE;
@@ -108,6 +116,7 @@
 		dest += bytes;
 		count -= bytes;
 	}
+	mutex_unlock(&hsa_buf_mutex);
 	return 0;
 }
 
@@ -229,8 +238,7 @@
 		rc = memcpy_hsa_kernel(zcore_ipl_block, ipib_info.ipib,
 				       PAGE_SIZE);
 	else
-		rc = memcpy_real(zcore_ipl_block, (void *) ipib_info.ipib,
-				 PAGE_SIZE);
+		rc = memcpy_real(zcore_ipl_block, ipib_info.ipib, PAGE_SIZE);
 	if (rc || (__force u32)csum_partial(zcore_ipl_block, zcore_ipl_block->hdr.len, 0) !=
 	    ipib_info.checksum) {
 		TRACE("Checksum does not match\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/airq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/airq.c
@@ -44,7 +44,7 @@
 	if (!airq->handler || airq->isc > MAX_ISC)
 		return -EINVAL;
 	if (!airq->lsi_ptr) {
-		airq->lsi_ptr = kzalloc(1, GFP_KERNEL);
+		airq->lsi_ptr = cio_dma_zalloc(1);
 		if (!airq->lsi_ptr)
 			return -ENOMEM;
 		airq->flags |= AIRQ_PTR_ALLOCATED;
@@ -79,7 +79,7 @@
 	synchronize_rcu();
 	isc_unregister(airq->isc);
 	if (airq->flags & AIRQ_PTR_ALLOCATED) {
-		kfree(airq->lsi_ptr);
+		cio_dma_free(airq->lsi_ptr, 1);
 		airq->lsi_ptr = NULL;
 		airq->flags &= ~AIRQ_PTR_ALLOCATED;
 	}
@@ -99,7 +99,7 @@
 	rcu_read_lock();
 	hlist_for_each_entry_rcu(airq, head, list)
 		if ((*airq->lsi_ptr & airq->lsi_mask) != 0)
-			airq->handler(airq, !tpi_info->directed_irq);
+			airq->handler(airq, tpi_info);
 	rcu_read_unlock();
 
 	return IRQ_HANDLED;
@@ -122,10 +122,12 @@
  * airq_iv_create - create an interrupt vector
  * @bits: number of bits in the interrupt vector
  * @flags: allocation flags
+ * @vec: pointer to pinned guest memory if AIRQ_IV_GUESTVEC
  *
  * Returns a pointer to an interrupt vector structure
  */
-struct airq_iv *airq_iv_create(unsigned long bits, unsigned long flags)
+struct airq_iv *airq_iv_create(unsigned long bits, unsigned long flags,
+			       unsigned long *vec)
 {
 	struct airq_iv *iv;
 	unsigned long size;
@@ -146,6 +148,8 @@
 					     &iv->vector_dma);
 		if (!iv->vector)
 			goto out_free;
+	} else if (flags & AIRQ_IV_GUESTVEC) {
+		iv->vector = vec;
 	} else {
 		iv->vector = cio_dma_zalloc(size);
 		if (!iv->vector)
@@ -185,7 +189,7 @@
 	kfree(iv->avail);
 	if (iv->flags & AIRQ_IV_CACHELINE && iv->vector)
 		dma_pool_free(airq_iv_cache, iv->vector, iv->vector_dma);
-	else
+	else if (!(iv->flags & AIRQ_IV_GUESTVEC))
 		cio_dma_free(iv->vector, size);
 	kfree(iv);
 out:
@@ -204,7 +208,7 @@
 	kfree(iv->bitlock);
 	if (iv->flags & AIRQ_IV_CACHELINE)
 		dma_pool_free(airq_iv_cache, iv->vector, iv->vector_dma);
-	else
+	else if (!(iv->flags & AIRQ_IV_GUESTVEC))
 		cio_dma_free(iv->vector, iv_size(iv->bits));
 	kfree(iv->avail);
 	kfree(iv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/chp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/chp.c
@@ -661,7 +661,8 @@
 	if (time_after(jiffies, chp_info_expires)) {
 		/* Data is too old, update. */
 		rc = sclp_chp_read_info(&chp_info);
-		chp_info_expires = jiffies + CHP_INFO_UPDATE_INTERVAL ;
+		if (!rc)
+			chp_info_expires = jiffies + CHP_INFO_UPDATE_INTERVAL;
 	}
 	mutex_unlock(&info_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/chsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/chsc.c
@@ -1255,7 +1255,7 @@
 EXPORT_SYMBOL_GPL(css_general_characteristics);
 EXPORT_SYMBOL_GPL(css_chsc_characteristics);
 
-int chsc_sstpc(void *page, unsigned int op, u16 ctrl, u64 *clock_delta)
+int chsc_sstpc(void *page, unsigned int op, u16 ctrl, long *clock_delta)
 {
 	struct {
 		struct chsc_header request;
@@ -1266,7 +1266,7 @@
 		unsigned int rsvd2[5];
 		struct chsc_header response;
 		unsigned int rsvd3[3];
-		u64 clock_delta;
+		s64 clock_delta;
 		unsigned int rsvd4[2];
 	} *rr;
 	int rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/cio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/cio.c
@@ -459,10 +459,14 @@
 {
 	struct schib schib;
 
-	if (stsch(sch->schid, &schib) || !css_sch_is_valid(&schib))
+	if (stsch(sch->schid, &schib))
 		return -ENODEV;
 
 	memcpy(&sch->schib, &schib, sizeof(schib));
+
+	if (!css_sch_is_valid(&schib))
+		return -EACCES;
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(cio_update_schib);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/cio_inject.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/cio_inject.c
@@ -95,7 +95,7 @@
 		return -EINVAL;
 	}
 
-	buffer = vmemdup_user(buf, lbuf);
+	buffer = memdup_user_nul(buf, lbuf);
 	if (IS_ERR(buffer))
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/css.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/css.c
@@ -233,17 +233,19 @@
 	 */
 	ret = dma_set_coherent_mask(&sch->dev, DMA_BIT_MASK(31));
 	if (ret)
-		goto err;
+		goto err_lock;
 	/*
 	 * But we don't have such restrictions imposed on the stuff that
 	 * is handled by the streaming API.
 	 */
 	ret = dma_set_mask(&sch->dev, DMA_BIT_MASK(64));
 	if (ret)
-		goto err;
+		goto err_lock;
 
 	return sch;
 
+err_lock:
+	kfree(sch->lock);
 err:
 	kfree(sch);
 	return ERR_PTR(ret);
@@ -437,8 +439,8 @@
 	struct subchannel *sch = to_subchannel(dev);
 	struct pmcw *pmcw = &sch->schib.pmcw;
 
-	if ((pmcw->st == SUBCHANNEL_TYPE_IO ||
-	     pmcw->st == SUBCHANNEL_TYPE_MSG) && pmcw->dnv)
+	if ((pmcw->st == SUBCHANNEL_TYPE_IO && pmcw->dnv) ||
+	    (pmcw->st == SUBCHANNEL_TYPE_MSG && pmcw->w))
 		return sysfs_emit(buf, "0.%x.%04x\n", sch->schid.ssid,
 				  pmcw->dev);
 	else
@@ -792,9 +794,8 @@
 {
 	struct idset *set = data;
 	struct subchannel *sch = to_subchannel(dev);
-	struct ccw_device *cdev = sch_get_cdev(sch);
 
-	if (cdev && cdev->online)
+	if (sch->st == SUBCHANNEL_TYPE_IO && sch->config.ena)
 		idset_sch_del(set, sch->schid);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/device.c
@@ -360,10 +360,8 @@
 
 	spin_lock_irq(cdev->ccwlock);
 	ret = ccw_device_online(cdev);
-	spin_unlock_irq(cdev->ccwlock);
-	if (ret == 0)
-		wait_event(cdev->private->wait_q, dev_fsm_final_state(cdev));
-	else {
+	if (ret) {
+		spin_unlock_irq(cdev->ccwlock);
 		CIO_MSG_EVENT(0, "ccw_device_online returned %d, "
 			      "device 0.%x.%04x\n",
 			      ret, cdev->private->dev_id.ssid,
@@ -372,7 +370,12 @@
 		put_device(&cdev->dev);
 		return ret;
 	}
-	spin_lock_irq(cdev->ccwlock);
+	/* Wait until a final state is reached */
+	while (!dev_fsm_final_state(cdev)) {
+		spin_unlock_irq(cdev->ccwlock);
+		wait_event(cdev->private->wait_q, dev_fsm_final_state(cdev));
+		spin_lock_irq(cdev->ccwlock);
+	}
 	/* Check if online processing was successful */
 	if ((cdev->private->state != DEV_STATE_ONLINE) &&
 	    (cdev->private->state != DEV_STATE_W4SENSE)) {
@@ -1116,6 +1119,8 @@
 	cdev = sch_get_cdev(sch);
 	if (cdev)
 		dev_fsm_event(cdev, DEV_EVENT_VERIFY);
+	else
+		css_schedule_eval(sch->schid);
 }
 
 static void io_subchannel_terminate_path(struct subchannel *sch, u8 mask)
@@ -1194,7 +1199,7 @@
 			else
 				path_event[chpid] = PE_NONE;
 		}
-		if (cdev)
+		if (cdev && cdev->drv && cdev->drv->path_event)
 			cdev->drv->path_event(cdev, path_event);
 		break;
 	}
@@ -1377,6 +1382,7 @@
 enum io_sch_action {
 	IO_SCH_UNREG,
 	IO_SCH_ORPH_UNREG,
+	IO_SCH_UNREG_CDEV,
 	IO_SCH_ATTACH,
 	IO_SCH_UNREG_ATTACH,
 	IO_SCH_ORPH_ATTACH,
@@ -1384,14 +1390,18 @@
 	IO_SCH_VERIFY,
 	IO_SCH_DISC,
 	IO_SCH_NOP,
+	IO_SCH_ORPH_CDEV,
 };
 
 static enum io_sch_action sch_get_action(struct subchannel *sch)
 {
 	struct ccw_device *cdev;
+	int rc;
 
 	cdev = sch_get_cdev(sch);
-	if (cio_update_schib(sch)) {
+	rc = cio_update_schib(sch);
+
+	if (rc == -ENODEV) {
 		/* Not operational. */
 		if (!cdev)
 			return IO_SCH_UNREG;
@@ -1399,6 +1409,16 @@
 			return IO_SCH_UNREG;
 		return IO_SCH_ORPH_UNREG;
 	}
+
+	/* Avoid unregistering subchannels without working device. */
+	if (rc == -EACCES) {
+		if (!cdev)
+			return IO_SCH_NOP;
+		if (ccw_device_notify(cdev, CIO_GONE) != NOTIFY_OK)
+			return IO_SCH_UNREG_CDEV;
+		return IO_SCH_ORPH_CDEV;
+	}
+
 	/* Operational. */
 	if (!cdev)
 		return IO_SCH_ATTACH;
@@ -1409,7 +1429,7 @@
 	}
 	if ((sch->schib.pmcw.pam & sch->opm) == 0) {
 		if (ccw_device_notify(cdev, CIO_NO_PATH) != NOTIFY_OK)
-			return IO_SCH_UNREG;
+			return IO_SCH_UNREG_CDEV;
 		return IO_SCH_DISC;
 	}
 	if (device_is_disconnected(cdev))
@@ -1468,9 +1488,11 @@
 		rc = 0;
 		goto out_unlock;
 	case IO_SCH_ORPH_UNREG:
+	case IO_SCH_ORPH_CDEV:
 	case IO_SCH_ORPH_ATTACH:
 		ccw_device_set_disconnected(cdev);
 		break;
+	case IO_SCH_UNREG_CDEV:
 	case IO_SCH_UNREG_ATTACH:
 	case IO_SCH_UNREG:
 		if (!cdev)
@@ -1498,12 +1520,14 @@
 	/* Handle attached ccw device. */
 	switch (action) {
 	case IO_SCH_ORPH_UNREG:
+	case IO_SCH_ORPH_CDEV:
 	case IO_SCH_ORPH_ATTACH:
 		/* Move ccw device to orphanage. */
 		rc = ccw_device_move_to_orph(cdev);
 		if (rc)
 			goto out;
 		break;
+	case IO_SCH_UNREG_CDEV:
 	case IO_SCH_UNREG_ATTACH:
 		spin_lock_irqsave(sch->lock, flags);
 		sch_set_cdev(sch, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/device_ops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/device_ops.c
@@ -825,13 +825,23 @@
  */
 void *ccw_device_dma_zalloc(struct ccw_device *cdev, size_t size)
 {
-	return cio_gp_dma_zalloc(cdev->private->dma_pool, &cdev->dev, size);
+	void *addr;
+
+	if (!get_device(&cdev->dev))
+		return NULL;
+	addr = cio_gp_dma_zalloc(cdev->private->dma_pool, &cdev->dev, size);
+	if (IS_ERR_OR_NULL(addr))
+		put_device(&cdev->dev);
+	return addr;
 }
 EXPORT_SYMBOL(ccw_device_dma_zalloc);
 
 void ccw_device_dma_free(struct ccw_device *cdev, void *cpu_addr, size_t size)
 {
+	if (!cpu_addr)
+		return;
 	cio_gp_dma_free(cdev->private->dma_pool, cpu_addr, size);
+	put_device(&cdev->dev);
 }
 EXPORT_SYMBOL(ccw_device_dma_free);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/idset.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/idset.c
@@ -16,20 +16,21 @@
 	unsigned long bitmap[];
 };
 
-static inline unsigned long bitmap_size(int num_ssid, int num_id)
+static inline unsigned long idset_bitmap_size(int num_ssid, int num_id)
 {
-	return BITS_TO_LONGS(num_ssid * num_id) * sizeof(unsigned long);
+	return bitmap_size(size_mul(num_ssid, num_id));
 }
 
 static struct idset *idset_new(int num_ssid, int num_id)
 {
 	struct idset *set;
 
-	set = vmalloc(sizeof(struct idset) + bitmap_size(num_ssid, num_id));
+	set = vmalloc(sizeof(struct idset) +
+		      idset_bitmap_size(num_ssid, num_id));
 	if (set) {
 		set->num_ssid = num_ssid;
 		set->num_id = num_id;
-		memset(set->bitmap, 0, bitmap_size(num_ssid, num_id));
+		memset(set->bitmap, 0, idset_bitmap_size(num_ssid, num_id));
 	}
 	return set;
 }
@@ -41,7 +42,8 @@
 
 void idset_fill(struct idset *set)
 {
-	memset(set->bitmap, 0xff, bitmap_size(set->num_ssid, set->num_id));
+	memset(set->bitmap, 0xff,
+	       idset_bitmap_size(set->num_ssid, set->num_id));
 }
 
 static inline void idset_add(struct idset *set, int ssid, int id)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/qdio.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/qdio.h
@@ -95,7 +95,7 @@
 		"	lgr	1,%[token]\n"
 		"	.insn	rsy,0xeb000000008a,%[qs],%[ccq],0(%[state])"
 		: [ccq] "+&d" (_ccq), [qs] "+&d" (_queuestart)
-		: [state] "d" ((unsigned long)state), [token] "d" (token)
+		: [state] "a" ((unsigned long)state), [token] "d" (token)
 		: "memory", "cc", "1");
 	*count = _ccq & 0xff;
 	*start = _queuestart & 0xff;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/qdio_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/qdio_main.c
@@ -679,8 +679,8 @@
 	lgr_info_log();
 }
 
-static void qdio_establish_handle_irq(struct qdio_irq *irq_ptr, int cstat,
-				      int dstat)
+static int qdio_establish_handle_irq(struct qdio_irq *irq_ptr, int cstat,
+				     int dstat, int dcc)
 {
 	DBF_DEV_EVENT(DBF_INFO, irq_ptr, "qest irq");
 
@@ -688,15 +688,18 @@
 		goto error;
 	if (dstat & ~(DEV_STAT_DEV_END | DEV_STAT_CHN_END))
 		goto error;
+	if (dcc == 1)
+		return -EAGAIN;
 	if (!(dstat & DEV_STAT_DEV_END))
 		goto error;
 	qdio_set_state(irq_ptr, QDIO_IRQ_STATE_ESTABLISHED);
-	return;
+	return 0;
 
 error:
 	DBF_ERROR("%4x EQ:error", irq_ptr->schid.sch_no);
 	DBF_ERROR("ds: %2x cs:%2x", dstat, cstat);
 	qdio_set_state(irq_ptr, QDIO_IRQ_STATE_ERR);
+	return -EIO;
 }
 
 /* qdio interrupt handler */
@@ -705,7 +708,7 @@
 {
 	struct qdio_irq *irq_ptr = cdev->private->qdio_data;
 	struct subchannel_id schid;
-	int cstat, dstat;
+	int cstat, dstat, rc, dcc;
 
 	if (!intparm || !irq_ptr) {
 		ccw_device_get_schid(cdev, &schid);
@@ -725,10 +728,12 @@
 	qdio_irq_check_sense(irq_ptr, irb);
 	cstat = irb->scsw.cmd.cstat;
 	dstat = irb->scsw.cmd.dstat;
+	dcc   = scsw_cmd_is_valid_cc(&irb->scsw) ? irb->scsw.cmd.cc : 0;
+	rc    = 0;
 
 	switch (irq_ptr->state) {
 	case QDIO_IRQ_STATE_INACTIVE:
-		qdio_establish_handle_irq(irq_ptr, cstat, dstat);
+		rc = qdio_establish_handle_irq(irq_ptr, cstat, dstat, dcc);
 		break;
 	case QDIO_IRQ_STATE_CLEANUP:
 		qdio_set_state(irq_ptr, QDIO_IRQ_STATE_INACTIVE);
@@ -742,12 +747,25 @@
 		if (cstat || dstat)
 			qdio_handle_activate_check(irq_ptr, intparm, cstat,
 						   dstat);
+		else if (dcc == 1)
+			rc = -EAGAIN;
 		break;
 	case QDIO_IRQ_STATE_STOPPED:
 		break;
 	default:
 		WARN_ON_ONCE(1);
 	}
+
+	if (rc == -EAGAIN) {
+		DBF_DEV_EVENT(DBF_INFO, irq_ptr, "qint retry");
+		rc = ccw_device_start(cdev, &irq_ptr->ccw, intparm, 0, 0);
+		if (!rc)
+			return;
+		DBF_ERROR("%4x RETRY ERR", irq_ptr->schid.sch_no);
+		DBF_ERROR("rc:%4x", rc);
+		qdio_set_state(irq_ptr, QDIO_IRQ_STATE_ERR);
+	}
+
 	wake_up(&cdev->private->wait_q);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/qdio_thinint.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/qdio_thinint.c
@@ -15,6 +15,7 @@
 #include <asm/qdio.h>
 #include <asm/airq.h>
 #include <asm/isc.h>
+#include <asm/tpi.h>
 
 #include "cio.h"
 #include "ioasm.h"
@@ -93,9 +94,10 @@
 /**
  * tiqdio_thinint_handler - thin interrupt handler for qdio
  * @airq: pointer to adapter interrupt descriptor
- * @floating: flag to recognize floating vs. directed interrupts (unused)
+ * @tpi_info: interrupt information (e.g. floating vs directed -- unused)
  */
-static void tiqdio_thinint_handler(struct airq_struct *airq, bool floating)
+static void tiqdio_thinint_handler(struct airq_struct *airq,
+				   struct tpi_info *tpi_info)
 {
 	u64 irq_time = S390_lowcore.int_clock;
 	u32 si_used = clear_shared_ind();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/trace.h
@@ -50,7 +50,7 @@
 		__entry->devno = schib->pmcw.dev;
 		__entry->schib = *schib;
 		__entry->pmcw_ena = schib->pmcw.ena;
-		__entry->pmcw_st = schib->pmcw.ena;
+		__entry->pmcw_st = schib->pmcw.st;
 		__entry->pmcw_dnv = schib->pmcw.dnv;
 		__entry->pmcw_dev = schib->pmcw.dev;
 		__entry->pmcw_lpm = schib->pmcw.lpm;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/cio/vfio_ccw_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/cio/vfio_ccw_drv.c
@@ -287,19 +287,11 @@
 	if (work_pending(&sch->todo_work))
 		goto out_unlock;
 
-	if (cio_update_schib(sch)) {
-		vfio_ccw_fsm_event(private, VFIO_CCW_EVENT_NOT_OPER);
-		rc = 0;
-		goto out_unlock;
-	}
-
-	private = dev_get_drvdata(&sch->dev);
-	if (private->state == VFIO_CCW_STATE_NOT_OPER) {
-		private->state = private->mdev ? VFIO_CCW_STATE_IDLE :
-				 VFIO_CCW_STATE_STANDBY;
-	}
 	rc = 0;
 
+	if (cio_update_schib(sch))
+		vfio_ccw_fsm_event(private, VFIO_CCW_EVENT_NOT_OPER);
+
 out_unlock:
 	spin_unlock_irqrestore(sch->lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/ap_bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/ap_bus.c
@@ -27,6 +27,7 @@
 #include <linux/kthread.h>
 #include <linux/mutex.h>
 #include <asm/airq.h>
+#include <asm/tpi.h>
 #include <linux/atomic.h>
 #include <asm/isc.h>
 #include <linux/hrtimer.h>
@@ -125,7 +126,8 @@
 static struct bus_type ap_bus_type;
 
 /* Adapter interrupt definitions */
-static void ap_interrupt_handler(struct airq_struct *airq, bool floating);
+static void ap_interrupt_handler(struct airq_struct *airq,
+				 struct tpi_info *tpi_info);
 
 static bool ap_irq_flag;
 
@@ -310,7 +312,7 @@
  * false otherwise.
  */
 static bool ap_queue_info(ap_qid_t qid, int *q_type, unsigned int *q_fac,
-			  int *q_depth, int *q_ml, bool *q_decfg)
+			  int *q_depth, int *q_ml, bool *q_decfg, bool *q_cstop)
 {
 	struct ap_queue_status status;
 	union {
@@ -353,6 +355,7 @@
 		*q_depth = tapq_info.tapq_gr2.qd;
 		*q_ml = tapq_info.tapq_gr2.ml;
 		*q_decfg = status.response_code == AP_RESPONSE_DECONFIGURED;
+		*q_cstop = status.response_code == AP_RESPONSE_CHECKSTOPPED;
 		switch (*q_type) {
 			/* For CEX2 and CEX3 the available functions
 			 * are not reflected by the facilities bits.
@@ -438,9 +441,10 @@
 /**
  * ap_interrupt_handler() - Schedule ap_tasklet on interrupt
  * @airq: pointer to adapter interrupt descriptor
- * @floating: ignored
+ * @tpi_info: ignored
  */
-static void ap_interrupt_handler(struct airq_struct *airq, bool floating)
+static void ap_interrupt_handler(struct airq_struct *airq,
+				 struct tpi_info *tpi_info)
 {
 	inc_irq_stat(IRQIO_APB);
 	tasklet_schedule(&ap_tasklet);
@@ -725,7 +729,7 @@
 		if (bound == apqns) {
 			if (!completion_done(&ap_init_apqn_bindings_complete)) {
 				complete_all(&ap_init_apqn_bindings_complete);
-				AP_DBF(DBF_INFO, "%s complete\n", __func__);
+				AP_DBF_INFO("%s complete\n", __func__);
 			}
 			ap_send_bindings_complete_uevent();
 		}
@@ -786,8 +790,8 @@
 		drvres = to_ap_drv(dev->driver)->flags
 			& AP_DRIVER_FLAG_DEFAULT;
 		if (!!devres != !!drvres) {
-			AP_DBF_DBG("reprobing queue=%02x.%04x\n",
-				   card, queue);
+			AP_DBF_DBG("%s reprobing queue=%02x.%04x\n",
+				   __func__, card, queue);
 			rc = device_reprobe(dev);
 		}
 	}
@@ -955,6 +959,10 @@
 
 void ap_bus_force_rescan(void)
 {
+	/* Only trigger AP bus scans after the initial scan is done */
+	if (atomic64_read(&ap_scan_bus_count) <= 0)
+		return;
+
 	/* processing a asynchronous bus rescan */
 	del_timer(&ap_config_timer);
 	queue_work(system_long_wq, &ap_scan_work);
@@ -1027,7 +1035,7 @@
  */
 static int modify_bitmap(const char *str, unsigned long *bitmap, int bits)
 {
-	int a, i, z;
+	unsigned long a, i, z;
 	char *np, sign;
 
 	/* bits needs to be a multiple of 8 */
@@ -1118,7 +1126,8 @@
 	ap_domain_index = domain;
 	spin_unlock_bh(&ap_domain_lock);
 
-	AP_DBF_INFO("stored new default domain=%d\n", domain);
+	AP_DBF_INFO("%s stored new default domain=%d\n",
+		    __func__, domain);
 
 	return count;
 }
@@ -1433,36 +1442,38 @@
 
 	/* < CEX2A is not supported */
 	if (rawtype < AP_DEVICE_TYPE_CEX2A) {
-		AP_DBF_WARN("get_comp_type queue=%02x.%04x unsupported type %d\n",
-			    AP_QID_CARD(qid), AP_QID_QUEUE(qid), rawtype);
+		AP_DBF_WARN("%s queue=%02x.%04x unsupported type %d\n",
+			    __func__, AP_QID_CARD(qid),
+			    AP_QID_QUEUE(qid), rawtype);
 		return 0;
 	}
-	/* up to CEX7 known and fully supported */
-	if (rawtype <= AP_DEVICE_TYPE_CEX7)
+	/* up to CEX8 known and fully supported */
+	if (rawtype <= AP_DEVICE_TYPE_CEX8)
 		return rawtype;
 	/*
-	 * unknown new type > CEX7, check for compatibility
+	 * unknown new type > CEX8, check for compatibility
 	 * to the highest known and supported type which is
-	 * currently CEX7 with the help of the QACT function.
+	 * currently CEX8 with the help of the QACT function.
 	 */
 	if (ap_qact_available()) {
 		struct ap_queue_status status;
 		union ap_qact_ap_info apinfo = {0};
 
 		apinfo.mode = (func >> 26) & 0x07;
-		apinfo.cat = AP_DEVICE_TYPE_CEX7;
+		apinfo.cat = AP_DEVICE_TYPE_CEX8;
 		status = ap_qact(qid, 0, &apinfo);
 		if (status.response_code == AP_RESPONSE_NORMAL
 		    && apinfo.cat >= AP_DEVICE_TYPE_CEX2A
-		    && apinfo.cat <= AP_DEVICE_TYPE_CEX7)
+		    && apinfo.cat <= AP_DEVICE_TYPE_CEX8)
 			comp_type = apinfo.cat;
 	}
 	if (!comp_type)
-		AP_DBF_WARN("get_comp_type queue=%02x.%04x unable to map type %d\n",
-			    AP_QID_CARD(qid), AP_QID_QUEUE(qid), rawtype);
+		AP_DBF_WARN("%s queue=%02x.%04x unable to map type %d\n",
+			    __func__, AP_QID_CARD(qid),
+			    AP_QID_QUEUE(qid), rawtype);
 	else if (comp_type != rawtype)
-		AP_DBF_INFO("get_comp_type queue=%02x.%04x map type %d to %d\n",
-			    AP_QID_CARD(qid), AP_QID_QUEUE(qid),
+		AP_DBF_INFO("%s queue=%02x.%04x map type %d to %d\n",
+			    __func__, AP_QID_CARD(qid), AP_QID_QUEUE(qid),
 			    rawtype, comp_type);
 	return comp_type;
 }
@@ -1514,7 +1525,7 @@
  */
 static inline void ap_scan_domains(struct ap_card *ac)
 {
-	bool decfg;
+	bool decfg, chkstop;
 	ap_qid_t qid;
 	unsigned int func;
 	struct device *dev;
@@ -1535,7 +1546,7 @@
 		aq = dev ? to_ap_queue(dev) : NULL;
 		if (!ap_test_config_usage_domain(dom)) {
 			if (dev) {
-				AP_DBF_INFO("%s(%d,%d) not in config any more, rm queue device\n",
+				AP_DBF_INFO("%s(%d,%d) not in config anymore, rm queue dev\n",
 					    __func__, ac->id, dom);
 				device_unregister(dev);
 				put_device(dev);
@@ -1543,11 +1554,11 @@
 			continue;
 		}
 		/* domain is valid, get info from this APQN */
-		if (!ap_queue_info(qid, &type, &func, &depth, &ml, &decfg)) {
+		if (!ap_queue_info(qid, &type, &func, &depth,
+				   &ml, &decfg, &chkstop)) {
 			if (aq) {
-				AP_DBF_INFO(
-					"%s(%d,%d) ap_queue_info() not successful, rm queue device\n",
-					__func__, ac->id, dom);
+				AP_DBF_INFO("%s(%d,%d) queue_info() failed, rm queue dev\n",
+					    __func__, ac->id, dom);
 				device_unregister(dev);
 				put_device(dev);
 			}
@@ -1563,6 +1574,7 @@
 			}
 			aq->card = ac;
 			aq->config = !decfg;
+			aq->chkstop = chkstop;
 			dev = &aq->ap_dev.device;
 			dev->bus = &ap_bus_type;
 			dev->parent = &ac->ap_dev.device;
@@ -1577,15 +1589,45 @@
 			/* get it and thus adjust reference counter */
 			get_device(dev);
 			if (decfg)
-				AP_DBF_INFO("%s(%d,%d) new (decfg) queue device created\n",
+				AP_DBF_INFO("%s(%d,%d) new (decfg) queue dev created\n",
+					    __func__, ac->id, dom);
+			else if (chkstop)
+				AP_DBF_INFO("%s(%d,%d) new (chkstop) queue dev created\n",
 					    __func__, ac->id, dom);
 			else
-				AP_DBF_INFO("%s(%d,%d) new queue device created\n",
+				AP_DBF_INFO("%s(%d,%d) new queue dev created\n",
 					    __func__, ac->id, dom);
 			goto put_dev_and_continue;
 		}
-		/* Check config state on the already existing queue device */
+		/* handle state changes on already existing queue device */
 		spin_lock_bh(&aq->lock);
+		/* checkstop state */
+		if (chkstop && !aq->chkstop) {
+			/* checkstop on */
+			aq->chkstop = true;
+			if (aq->dev_state > AP_DEV_STATE_UNINITIATED) {
+				aq->dev_state = AP_DEV_STATE_ERROR;
+				aq->last_err_rc = AP_RESPONSE_CHECKSTOPPED;
+			}
+			spin_unlock_bh(&aq->lock);
+			AP_DBF_DBG("%s(%d,%d) queue dev checkstop on\n",
+				   __func__, ac->id, dom);
+			/* 'receive' pending messages with -EAGAIN */
+			ap_flush_queue(aq);
+			goto put_dev_and_continue;
+		} else if (!chkstop && aq->chkstop) {
+			/* checkstop off */
+			aq->chkstop = false;
+			if (aq->dev_state > AP_DEV_STATE_UNINITIATED) {
+				aq->dev_state = AP_DEV_STATE_OPERATING;
+				aq->sm_state = AP_SM_STATE_RESET_START;
+			}
+			spin_unlock_bh(&aq->lock);
+			AP_DBF_DBG("%s(%d,%d) queue dev checkstop off\n",
+				   __func__, ac->id, dom);
+			goto put_dev_and_continue;
+		}
+		/* config state change */
 		if (decfg && aq->config) {
 			/* config off this queue device */
 			aq->config = false;
@@ -1594,14 +1636,13 @@
 				aq->last_err_rc = AP_RESPONSE_DECONFIGURED;
 			}
 			spin_unlock_bh(&aq->lock);
-			AP_DBF_INFO("%s(%d,%d) queue device config off\n",
-				    __func__, ac->id, dom);
+			AP_DBF_DBG("%s(%d,%d) queue dev config off\n",
+				   __func__, ac->id, dom);
 			ap_send_config_uevent(&aq->ap_dev, aq->config);
 			/* 'receive' pending messages with -EAGAIN */
 			ap_flush_queue(aq);
 			goto put_dev_and_continue;
-		}
-		if (!decfg && !aq->config) {
+		} else if (!decfg && !aq->config) {
 			/* config on this queue device */
 			aq->config = true;
 			if (aq->dev_state > AP_DEV_STATE_UNINITIATED) {
@@ -1609,8 +1650,8 @@
 				aq->sm_state = AP_SM_STATE_RESET_START;
 			}
 			spin_unlock_bh(&aq->lock);
-			AP_DBF_INFO("%s(%d,%d) queue device config on\n",
-				    __func__, ac->id, dom);
+			AP_DBF_DBG("%s(%d,%d) queue dev config on\n",
+				   __func__, ac->id, dom);
 			ap_send_config_uevent(&aq->ap_dev, aq->config);
 			goto put_dev_and_continue;
 		}
@@ -1621,7 +1662,7 @@
 			ap_flush_queue(aq);
 			/* re-init (with reset) the queue device */
 			ap_queue_init_state(aq);
-			AP_DBF_INFO("%s(%d,%d) queue device reinit enforced\n",
+			AP_DBF_INFO("%s(%d,%d) queue dev reinit enforced\n",
 				    __func__, ac->id, dom);
 			goto put_dev_and_continue;
 		}
@@ -1637,7 +1678,7 @@
  */
 static inline void ap_scan_adapter(int ap)
 {
-	bool decfg;
+	bool decfg, chkstop;
 	ap_qid_t qid;
 	unsigned int func;
 	struct device *dev;
@@ -1653,7 +1694,7 @@
 	/* Adapter not in configuration ? */
 	if (!ap_test_config_card_id(ap)) {
 		if (ac) {
-			AP_DBF_INFO("%s(%d) ap not in config any more, rm card and queue devices\n",
+			AP_DBF_INFO("%s(%d) ap not in config any more, rm card and queue devs\n",
 				    __func__, ap);
 			ap_scan_rm_card_dev_and_queue_devs(ac);
 			put_device(dev);
@@ -1671,16 +1712,15 @@
 	for (dom = 0; dom <= ap_max_domain_id; dom++)
 		if (ap_test_config_usage_domain(dom)) {
 			qid = AP_MKQID(ap, dom);
-			if (ap_queue_info(qid, &type, &func,
-					  &depth, &ml, &decfg))
+			if (ap_queue_info(qid, &type, &func, &depth,
+					  &ml, &decfg, &chkstop))
 				break;
 		}
 	if (dom > ap_max_domain_id) {
 		/* Could not find a valid APQN for this adapter */
 		if (ac) {
-			AP_DBF_INFO(
-				"%s(%d) no type info (no APQN found), rm card and queue devices\n",
-				__func__, ap);
+			AP_DBF_INFO("%s(%d) no type info (no APQN found), rm card and queue devs\n",
+				    __func__, ap);
 			ap_scan_rm_card_dev_and_queue_devs(ac);
 			put_device(dev);
 		} else {
@@ -1692,7 +1732,7 @@
 	if (!type) {
 		/* No apdater type info available, an unusable adapter */
 		if (ac) {
-			AP_DBF_INFO("%s(%d) no valid type (0) info, rm card and queue devices\n",
+			AP_DBF_INFO("%s(%d) no valid type (0) info, rm card and queue devs\n",
 				    __func__, ap);
 			ap_scan_rm_card_dev_and_queue_devs(ac);
 			put_device(dev);
@@ -1706,27 +1746,39 @@
 	if (ac) {
 		/* Check APQN against existing card device for changes */
 		if (ac->raw_hwtype != type) {
-			AP_DBF_INFO("%s(%d) hwtype %d changed, rm card and queue devices\n",
+			AP_DBF_INFO("%s(%d) hwtype %d changed, rm card and queue devs\n",
 				    __func__, ap, type);
 			ap_scan_rm_card_dev_and_queue_devs(ac);
 			put_device(dev);
 			ac = NULL;
 		} else if (ac->functions != func) {
-			AP_DBF_INFO("%s(%d) functions 0x%08x changed, rm card and queue devices\n",
+			AP_DBF_INFO("%s(%d) functions 0x%08x changed, rm card and queue devs\n",
 				    __func__, ap, type);
 			ap_scan_rm_card_dev_and_queue_devs(ac);
 			put_device(dev);
 			ac = NULL;
 		} else {
+			/* handle checkstop state change */
+			if (chkstop && !ac->chkstop) {
+				/* checkstop on */
+				ac->chkstop = true;
+				AP_DBF_INFO("%s(%d) card dev checkstop on\n",
+					    __func__, ap);
+			} else if (!chkstop && ac->chkstop) {
+				/* checkstop off */
+				ac->chkstop = false;
+				AP_DBF_INFO("%s(%d) card dev checkstop off\n",
+					    __func__, ap);
+			}
+			/* handle config state change */
 			if (decfg && ac->config) {
 				ac->config = false;
-				AP_DBF_INFO("%s(%d) card device config off\n",
+				AP_DBF_INFO("%s(%d) card dev config off\n",
 					    __func__, ap);
 				ap_send_config_uevent(&ac->ap_dev, ac->config);
-			}
-			if (!decfg && !ac->config) {
+			} else if (!decfg && !ac->config) {
 				ac->config = true;
-				AP_DBF_INFO("%s(%d) card device config on\n",
+				AP_DBF_INFO("%s(%d) card dev config on\n",
 					    __func__, ap);
 				ap_send_config_uevent(&ac->ap_dev, ac->config);
 			}
@@ -1748,6 +1800,7 @@
 			return;
 		}
 		ac->config = !decfg;
+		ac->chkstop = chkstop;
 		dev = &ac->ap_dev.device;
 		dev->bus = &ap_bus_type;
 		dev->parent = ap_root_device;
@@ -1756,7 +1809,8 @@
 		if (ac->maxmsgsize > atomic_read(&ap_max_msg_size)) {
 			atomic_set(&ap_max_msg_size, ac->maxmsgsize);
 			AP_DBF_INFO("%s(%d) ap_max_msg_size update to %d byte\n",
-				    __func__, ap, atomic_read(&ap_max_msg_size));
+				    __func__, ap,
+				    atomic_read(&ap_max_msg_size));
 		}
 		/* Register the new card device with AP bus */
 		rc = device_register(dev);
@@ -1769,10 +1823,13 @@
 		/* get it and thus adjust reference counter */
 		get_device(dev);
 		if (decfg)
-			AP_DBF_INFO("%s(%d) new (decfg) card device type=%d func=0x%08x created\n",
+			AP_DBF_INFO("%s(%d) new (decfg) card dev type=%d func=0x%08x created\n",
+				    __func__, ap, type, func);
+		else if (chkstop)
+			AP_DBF_INFO("%s(%d) new (chkstop) card dev type=%d func=0x%08x created\n",
 				    __func__, ap, type, func);
 		else
-			AP_DBF_INFO("%s(%d) new card device type=%d func=0x%08x created\n",
+			AP_DBF_INFO("%s(%d) new card dev type=%d func=0x%08x created\n",
 				    __func__, ap, type, func);
 	}
 
@@ -1810,12 +1867,12 @@
 		if (dev)
 			put_device(dev);
 		else
-			AP_DBF_INFO("no queue device with default domain %d available\n",
-				    ap_domain_index);
+			AP_DBF_INFO("%s no queue device with default domain %d available\n",
+				    __func__, ap_domain_index);
 	}
 
 	if (atomic64_inc_return(&ap_scan_bus_count) == 1) {
-		AP_DBF(DBF_DEBUG, "%s init scan complete\n", __func__);
+		AP_DBF_DBG("%s init scan complete\n", __func__);
 		ap_send_init_scan_done_uevent();
 		ap_check_bindings_complete();
 	}
@@ -1830,7 +1887,7 @@
 
 static int __init ap_debug_init(void)
 {
-	ap_dbf_info = debug_register("ap", 1, 1,
+	ap_dbf_info = debug_register("ap", 2, 1,
 				     DBF_MAX_SPRINTF_ARGS * sizeof(long));
 	debug_register_view(ap_dbf_info, &debug_sprintf_view);
 	debug_set_level(ap_dbf_info, DBF_ERR);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/ap_bus.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/ap_bus.h
@@ -69,6 +69,7 @@
 #define AP_DEVICE_TYPE_CEX5	11
 #define AP_DEVICE_TYPE_CEX6	12
 #define AP_DEVICE_TYPE_CEX7	13
+#define AP_DEVICE_TYPE_CEX8	14
 
 /*
  * Known function facilities
@@ -164,6 +165,7 @@
 	int id;				/* AP card number. */
 	unsigned int maxmsgsize;	/* AP msg limit for this card */
 	bool config;			/* configured state */
+	bool chkstop;			/* checkstop state */
 	atomic64_t total_request_count;	/* # requests ever for this AP device.*/
 };
 
@@ -176,6 +178,7 @@
 	spinlock_t lock;		/* Per device lock. */
 	enum ap_dev_state dev_state;	/* queue device state */
 	bool config;			/* configured state */
+	bool chkstop;			/* checkstop state */
 	ap_qid_t qid;			/* AP queue id. */
 	bool interrupt;			/* indicate if interrupts are enabled */
 	int queue_count;		/* # messages currently on AP queue. */
@@ -234,7 +237,9 @@
 			struct ap_message *);
 };
 
-#define AP_MSG_FLAG_SPECIAL  1		/* flag msg as 'special' with NQAP */
+#define AP_MSG_FLAG_SPECIAL  0x0001	/* flag msg as 'special' with NQAP */
+#define AP_MSG_FLAG_USAGE    0x0002	/* CCA, EP11: usage (no admin) msg */
+#define AP_MSG_FLAG_ADMIN    0x0004	/* CCA, EP11: admin (=control) msg */
 
 /**
  * ap_init_message() - Initialize ap_message.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/ap_card.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/ap_card.c
@@ -174,6 +174,16 @@
 
 static DEVICE_ATTR_RW(config);
 
+static ssize_t chkstop_show(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	struct ap_card *ac = to_ap_card(dev);
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", ac->chkstop ? 1 : 0);
+}
+
+static DEVICE_ATTR_RO(chkstop);
+
 static ssize_t max_msg_size_show(struct device *dev,
 				 struct device_attribute *attr, char *buf)
 {
@@ -194,6 +204,7 @@
 	&dev_attr_pendingq_count.attr,
 	&dev_attr_modalias.attr,
 	&dev_attr_config.attr,
+	&dev_attr_chkstop.attr,
 	&dev_attr_max_msg_size.attr,
 	NULL
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/ap_debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/ap_debug.h
@@ -16,7 +16,7 @@
 #define RC2ERR(rc) ((rc) ? DBF_ERR : DBF_INFO)
 #define RC2WARN(rc) ((rc) ? DBF_WARN : DBF_INFO)
 
-#define DBF_MAX_SPRINTF_ARGS 5
+#define DBF_MAX_SPRINTF_ARGS 6
 
 #define AP_DBF(...)					\
 	debug_sprintf_event(ap_dbf_info, ##__VA_ARGS__)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/ap_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/ap_queue.c
@@ -157,6 +157,8 @@
 	switch (status.response_code) {
 	case AP_RESPONSE_NORMAL:
 		aq->queue_count = max_t(int, 0, aq->queue_count - 1);
+		if (!status.queue_empty && !aq->queue_count)
+			aq->queue_count++;
 		if (aq->queue_count > 0)
 			mod_timer(&aq->timeout,
 				  jiffies + aq->request_timeout);
@@ -246,6 +248,7 @@
 
 	if (aq->requestq_count <= 0)
 		return AP_SM_WAIT_NONE;
+
 	/* Start the next request on the queue. */
 	ap_msg = list_entry(aq->requestq.next, struct ap_message, list);
 #ifdef CONFIG_ZCRYPT_DEBUG
@@ -279,7 +282,7 @@
 		aq->sm_state = AP_SM_STATE_RESET_WAIT;
 		return AP_SM_WAIT_TIMEOUT;
 	case AP_RESPONSE_INVALID_DOMAIN:
-		AP_DBF(DBF_WARN, "AP_RESPONSE_INVALID_DOMAIN on NQAP\n");
+		AP_DBF_WARN("%s RESPONSE_INVALID_DOMAIN on NQAP\n", __func__);
 		fallthrough;
 	case AP_RESPONSE_MESSAGE_TOO_BIG:
 	case AP_RESPONSE_REQ_FAC_NOT_INST:
@@ -452,7 +455,8 @@
 
 enum ap_sm_wait ap_sm_event(struct ap_queue *aq, enum ap_sm_event event)
 {
-	if (aq->dev_state > AP_DEV_STATE_UNINITIATED)
+	if (aq->config && !aq->chkstop &&
+	    aq->dev_state > AP_DEV_STATE_UNINITIATED)
 		return ap_jumptable[aq->sm_state][event](aq);
 	else
 		return AP_SM_WAIT_NONE;
@@ -571,8 +575,8 @@
 	ap_wait(ap_sm_event(aq, AP_SM_EVENT_POLL));
 	spin_unlock_bh(&aq->lock);
 
-	AP_DBF(DBF_INFO, "reset queue=%02x.%04x triggered by user\n",
-	       AP_QID_CARD(aq->qid), AP_QID_QUEUE(aq->qid));
+	AP_DBF_INFO("%s reset queue=%02x.%04x triggered by user\n",
+		    __func__, AP_QID_CARD(aq->qid), AP_QID_QUEUE(aq->qid));
 
 	return count;
 }
@@ -612,6 +616,20 @@
 
 static DEVICE_ATTR_RO(config);
 
+static ssize_t chkstop_show(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	struct ap_queue *aq = to_ap_queue(dev);
+	int rc;
+
+	spin_lock_bh(&aq->lock);
+	rc = scnprintf(buf, PAGE_SIZE, "%d\n", aq->chkstop ? 1 : 0);
+	spin_unlock_bh(&aq->lock);
+	return rc;
+}
+
+static DEVICE_ATTR_RO(chkstop);
+
 #ifdef CONFIG_ZCRYPT_DEBUG
 static ssize_t states_show(struct device *dev,
 			   struct device_attribute *attr, char *buf)
@@ -726,6 +744,7 @@
 	&dev_attr_reset.attr,
 	&dev_attr_interrupt.attr,
 	&dev_attr_config.attr,
+	&dev_attr_chkstop.attr,
 #ifdef CONFIG_ZCRYPT_DEBUG
 	&dev_attr_states.attr,
 	&dev_attr_last_err_rc.attr,
@@ -912,6 +931,7 @@
 	spin_lock_bh(&aq->lock);
 	aq->dev_state = AP_DEV_STATE_OPERATING;
 	aq->sm_state = AP_SM_STATE_RESET_START;
+	aq->last_err_rc = 0;
 	ap_wait(ap_sm_event(aq, AP_SM_EVENT_POLL));
 	spin_unlock_bh(&aq->lock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/pkey_api.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/pkey_api.c
@@ -744,7 +744,7 @@
 		if (ktype)
 			*ktype = PKEY_TYPE_EP11;
 		if (ksize)
-			*ksize = kb->head.keybitlen;
+			*ksize = kb->head.bitlen;
 
 		rc = ep11_findcard2(&_apqns, &_nr_apqns, *cardnr, *domain,
 				    ZCRYPT_CEX7, EP11_API_V, kb->wkvp);
@@ -1167,10 +1167,8 @@
 		rc = cca_clr2seckey(kcs.cardnr, kcs.domain, kcs.keytype,
 				    kcs.clrkey.clrkey, kcs.seckey.seckey);
 		DEBUG_DBG("%s cca_clr2seckey()=%d\n", __func__, rc);
-		if (rc)
-			break;
-		if (copy_to_user(ucs, &kcs, sizeof(kcs)))
-			return -EFAULT;
+		if (!rc && copy_to_user(ucs, &kcs, sizeof(kcs)))
+			rc = -EFAULT;
 		memzero_explicit(&kcs, sizeof(kcs));
 		break;
 	}
@@ -1199,10 +1197,8 @@
 		rc = pkey_clr2protkey(kcp.keytype,
 				      &kcp.clrkey, &kcp.protkey);
 		DEBUG_DBG("%s pkey_clr2protkey()=%d\n", __func__, rc);
-		if (rc)
-			break;
-		if (copy_to_user(ucp, &kcp, sizeof(kcp)))
-			return -EFAULT;
+		if (!rc && copy_to_user(ucp, &kcp, sizeof(kcp)))
+			rc = -EFAULT;
 		memzero_explicit(&kcp, sizeof(kcp));
 		break;
 	}
@@ -1286,7 +1282,7 @@
 			return PTR_ERR(kkey);
 		rc = pkey_keyblob2pkey(kkey, ktp.keylen, &ktp.protkey);
 		DEBUG_DBG("%s pkey_keyblob2pkey()=%d\n", __func__, rc);
-		kfree(kkey);
+		kfree_sensitive(kkey);
 		if (rc)
 			break;
 		if (copy_to_user(utp, &ktp, sizeof(ktp)))
@@ -1345,11 +1341,14 @@
 		if (copy_from_user(&kcs, ucs, sizeof(kcs)))
 			return -EFAULT;
 		apqns = _copy_apqns_from_user(kcs.apqns, kcs.apqn_entries);
-		if (IS_ERR(apqns))
+		if (IS_ERR(apqns)) {
+			memzero_explicit(&kcs, sizeof(kcs));
 			return PTR_ERR(apqns);
+		}
 		kkey = kmalloc(klen, GFP_KERNEL);
 		if (!kkey) {
 			kfree(apqns);
+			memzero_explicit(&kcs, sizeof(kcs));
 			return -ENOMEM;
 		}
 		rc = pkey_clr2seckey2(apqns, kcs.apqn_entries,
@@ -1359,15 +1358,18 @@
 		kfree(apqns);
 		if (rc) {
 			kfree(kkey);
+			memzero_explicit(&kcs, sizeof(kcs));
 			break;
 		}
 		if (kcs.key) {
 			if (kcs.keylen < klen) {
 				kfree(kkey);
+				memzero_explicit(&kcs, sizeof(kcs));
 				return -EINVAL;
 			}
 			if (copy_to_user(kcs.key, kkey, klen)) {
 				kfree(kkey);
+				memzero_explicit(&kcs, sizeof(kcs));
 				return -EFAULT;
 			}
 		}
@@ -1419,7 +1421,7 @@
 					kkey, ktp.keylen, &ktp.protkey);
 		DEBUG_DBG("%s pkey_keyblob2pkey2()=%d\n", __func__, rc);
 		kfree(apqns);
-		kfree(kkey);
+		kfree_sensitive(kkey);
 		if (rc)
 			break;
 		if (copy_to_user(utp, &ktp, sizeof(ktp)))
@@ -1545,7 +1547,7 @@
 					protkey, &protkeylen);
 		DEBUG_DBG("%s pkey_keyblob2pkey3()=%d\n", __func__, rc);
 		kfree(apqns);
-		kfree(kkey);
+		kfree_sensitive(kkey);
 		if (rc) {
 			kfree(protkey);
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/vfio_ap_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/vfio_ap_drv.c
@@ -36,6 +36,8 @@
 	  .match_flags = AP_DEVICE_ID_MATCH_QUEUE_TYPE },
 	{ .dev_type = AP_DEVICE_TYPE_CEX7,
 	  .match_flags = AP_DEVICE_ID_MATCH_QUEUE_TYPE },
+	{ .dev_type = AP_DEVICE_TYPE_CEX8,
+	  .match_flags = AP_DEVICE_ID_MATCH_QUEUE_TYPE },
 	{ /* end of sibling */ },
 };
 
@@ -86,8 +88,9 @@
 
 static void vfio_ap_matrix_dev_release(struct device *dev)
 {
-	struct ap_matrix_dev *matrix_dev = dev_get_drvdata(dev);
+	struct ap_matrix_dev *matrix_dev;
 
+	matrix_dev = container_of(dev, struct ap_matrix_dev, device);
 	kfree(matrix_dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_api.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_api.c
@@ -82,8 +82,8 @@
 		atomic_set(&zcrypt_rescan_req, 0);
 		atomic_inc(&zcrypt_rescan_count);
 		ap_bus_force_rescan();
-		ZCRYPT_DBF(DBF_INFO, "rescan count=%07d\n",
-			   atomic_inc_return(&zcrypt_rescan_count));
+		ZCRYPT_DBF_INFO("%s rescan count=%07d\n", __func__,
+				atomic_inc_return(&zcrypt_rescan_count));
 		return 1;
 	}
 	return 0;
@@ -341,8 +341,8 @@
 {
 	struct zcdn_device *zcdndev = to_zcdn_dev(dev);
 
-	ZCRYPT_DBF(DBF_INFO, "releasing zcdn device %d:%d\n",
-		   MAJOR(dev->devt), MINOR(dev->devt));
+	ZCRYPT_DBF_INFO("%s releasing zcdn device %d:%d\n",
+			__func__, MAJOR(dev->devt), MINOR(dev->devt));
 
 	kfree(zcdndev);
 }
@@ -398,6 +398,7 @@
 			 ZCRYPT_NAME "_%d", (int) MINOR(devt));
 	nodename[sizeof(nodename)-1] = '\0';
 	if (dev_set_name(&zcdndev->device, nodename)) {
+		kfree(zcdndev);
 		rc = -EINVAL;
 		goto unlockout;
 	}
@@ -407,8 +408,8 @@
 		goto unlockout;
 	}
 
-	ZCRYPT_DBF(DBF_INFO, "created zcdn device %d:%d\n",
-		   MAJOR(devt), MINOR(devt));
+	ZCRYPT_DBF_INFO("%s created zcdn device %d:%d\n",
+			__func__, MAJOR(devt), MINOR(devt));
 
 unlockout:
 	mutex_unlock(&ap_perms_mutex);
@@ -550,9 +551,8 @@
 	}
 
 	if (rc)
-		ZCRYPT_DBF(DBF_WARN,
-			   "ioctl check failed: ioctlnr=0x%04x rc=%d\n",
-			   ioctlnr, rc);
+		ZCRYPT_DBF_WARN("%s ioctl check failed: ioctlnr=0x%04x rc=%d\n",
+				__func__, ioctlnr, rc);
 
 	return rc;
 }
@@ -574,6 +574,7 @@
 {
 	if (!zq || !try_module_get(zq->queue->ap_dev.device.driver->owner))
 		return NULL;
+	zcrypt_card_get(zc);
 	zcrypt_queue_get(zq);
 	get_device(&zq->queue->ap_dev.device);
 	atomic_add(weight, &zc->load);
@@ -593,6 +594,7 @@
 	atomic_sub(weight, &zq->load);
 	put_device(&zq->queue->ap_dev.device);
 	zcrypt_queue_put(zq);
+	zcrypt_card_put(zc);
 	module_put(mod);
 }
 
@@ -672,7 +674,7 @@
 	spin_lock(&zcrypt_list_lock);
 	for_each_zcrypt_card(zc) {
 		/* Check for useable accelarator or CCA card */
-		if (!zc->online || !zc->card->config ||
+		if (!zc->online || !zc->card->config || zc->card->chkstop ||
 		    !(zc->card->functions & 0x18000000))
 			continue;
 		/* Check for size limits */
@@ -693,7 +695,7 @@
 		for_each_zcrypt_queue(zq, zc) {
 			/* check if device is useable and eligible */
 			if (!zq->online || !zq->ops->rsa_modexpo ||
-			    !zq->queue->config)
+			    !zq->queue->config || zq->queue->chkstop)
 				continue;
 			/* check if device node has admission for this queue */
 			if (!zcrypt_check_queue(perms,
@@ -715,6 +717,8 @@
 	spin_unlock(&zcrypt_list_lock);
 
 	if (!pref_zq) {
+		ZCRYPT_DBF_DBG("%s no matching queue found => ENODEV\n",
+			       __func__);
 		rc = -ENODEV;
 		goto out;
 	}
@@ -780,7 +784,7 @@
 	spin_lock(&zcrypt_list_lock);
 	for_each_zcrypt_card(zc) {
 		/* Check for useable accelarator or CCA card */
-		if (!zc->online || !zc->card->config ||
+		if (!zc->online || !zc->card->config || zc->card->chkstop ||
 		    !(zc->card->functions & 0x18000000))
 			continue;
 		/* Check for size limits */
@@ -801,7 +805,7 @@
 		for_each_zcrypt_queue(zq, zc) {
 			/* check if device is useable and eligible */
 			if (!zq->online || !zq->ops->rsa_modexpo_crt ||
-			    !zq->queue->config)
+			    !zq->queue->config || zq->queue->chkstop)
 				continue;
 			/* check if device node has admission for this queue */
 			if (!zcrypt_check_queue(perms,
@@ -823,6 +827,8 @@
 	spin_unlock(&zcrypt_list_lock);
 
 	if (!pref_zq) {
+		ZCRYPT_DBF_DBG("%s no matching queue found => ENODEV\n",
+			       __func__);
 		rc = -ENODEV;
 		goto out;
 	}
@@ -873,7 +879,7 @@
 	}
 #endif
 
-	rc = get_cprb_fc(userspace, xcRB, &ap_msg, &func_code, &domain);
+	rc = prep_cca_ap_msg(userspace, xcRB, &ap_msg, &func_code, &domain);
 	if (rc)
 		goto out;
 
@@ -893,7 +899,7 @@
 	spin_lock(&zcrypt_list_lock);
 	for_each_zcrypt_card(zc) {
 		/* Check for useable CCA card */
-		if (!zc->online || !zc->card->config ||
+		if (!zc->online || !zc->card->config || zc->card->chkstop ||
 		    !(zc->card->functions & 0x10000000))
 			continue;
 		/* Check for user selected CCA card */
@@ -916,9 +922,8 @@
 			continue;
 		for_each_zcrypt_queue(zq, zc) {
 			/* check for device useable and eligible */
-			if (!zq->online ||
-			    !zq->ops->send_cprb ||
-			    !zq->queue->config ||
+			if (!zq->online || !zq->ops->send_cprb ||
+			    !zq->queue->config || zq->queue->chkstop ||
 			    (tdom != AUTOSEL_DOM &&
 			     tdom != AP_QID_QUEUE(zq->queue->qid)))
 				continue;
@@ -942,6 +947,8 @@
 	spin_unlock(&zcrypt_list_lock);
 
 	if (!pref_zq) {
+		ZCRYPT_DBF_DBG("%s no match for address %02x.%04x => ENODEV\n",
+			       __func__, xcRB->user_defined, *domain);
 		rc = -ENODEV;
 		goto out;
 	}
@@ -1018,7 +1025,7 @@
 	struct ep11_target_dev *targets;
 	unsigned short target_num;
 	unsigned int wgt = 0, pref_wgt = 0;
-	unsigned int func_code;
+	unsigned int func_code, domain;
 	struct ap_message ap_msg;
 	int cpen, qpen, qid = 0, rc = -ENODEV;
 	struct module *mod;
@@ -1055,7 +1062,7 @@
 		}
 	}
 
-	rc = get_ep11cprb_fc(userspace, xcrb, &ap_msg, &func_code);
+	rc = prep_ep11_ap_msg(userspace, xcrb, &ap_msg, &func_code, &domain);
 	if (rc)
 		goto out_free;
 
@@ -1064,7 +1071,7 @@
 	spin_lock(&zcrypt_list_lock);
 	for_each_zcrypt_card(zc) {
 		/* Check for useable EP11 card */
-		if (!zc->online || !zc->card->config ||
+		if (!zc->online || !zc->card->config || zc->card->chkstop ||
 		    !(zc->card->functions & 0x04000000))
 			continue;
 		/* Check for user selected EP11 card */
@@ -1087,9 +1094,8 @@
 			continue;
 		for_each_zcrypt_queue(zq, zc) {
 			/* check if device is useable and eligible */
-			if (!zq->online ||
-			    !zq->ops->send_ep11_cprb ||
-			    !zq->queue->config ||
+			if (!zq->online || !zq->ops->send_ep11_cprb ||
+			    !zq->queue->config || zq->queue->chkstop ||
 			    (targets &&
 			     !is_desired_ep11_queue(zq->queue->qid,
 						    target_num, targets)))
@@ -1114,6 +1120,17 @@
 	spin_unlock(&zcrypt_list_lock);
 
 	if (!pref_zq) {
+		if (targets && target_num == 1) {
+			ZCRYPT_DBF_DBG("%s no match for address %02x.%04x => ENODEV\n",
+				       __func__, (int) targets->ap_id,
+				       (int) targets->dom_id);
+		} else if (targets) {
+			ZCRYPT_DBF_DBG("%s no match for %d target addrs => ENODEV\n",
+				       __func__, (int) target_num);
+		} else {
+			ZCRYPT_DBF_DBG("%s no match for address ff.ffff => ENODEV\n",
+				       __func__);
+		}
 		rc = -ENODEV;
 		goto out_free;
 	}
@@ -1158,7 +1175,7 @@
 	trace_s390_zcrypt_req(buffer, TP_HWRNGCPRB);
 
 	ap_init_message(&ap_msg);
-	rc = get_rng_fc(&ap_msg, &func_code, &domain);
+	rc = prep_rng_ap_msg(&ap_msg, &func_code, &domain);
 	if (rc)
 		goto out;
 
@@ -1167,7 +1184,7 @@
 	spin_lock(&zcrypt_list_lock);
 	for_each_zcrypt_card(zc) {
 		/* Check for useable CCA card */
-		if (!zc->online || !zc->card->config ||
+		if (!zc->online || !zc->card->config || zc->card->chkstop ||
 		    !(zc->card->functions & 0x10000000))
 			continue;
 		/* get weight index of the card device	*/
@@ -1177,7 +1194,7 @@
 		for_each_zcrypt_queue(zq, zc) {
 			/* check if device is useable and eligible */
 			if (!zq->online || !zq->ops->rng ||
-			    !zq->queue->config)
+			    !zq->queue->config || zq->queue->chkstop)
 				continue;
 			if (!zcrypt_queue_compare(zq, pref_zq, wgt, pref_wgt))
 				continue;
@@ -1190,6 +1207,8 @@
 	spin_unlock(&zcrypt_list_lock);
 
 	if (!pref_zq) {
+		ZCRYPT_DBF_DBG("%s no matching queue found => ENODEV\n",
+			__func__);
 		rc = -ENODEV;
 		goto out;
 	}
@@ -1446,7 +1465,7 @@
 	if (rc == -EAGAIN && tr.again_counter >= TRACK_AGAIN_MAX)
 		rc = -EIO;
 	if (rc) {
-		ZCRYPT_DBF(DBF_DEBUG, "ioctl ICARSAMODEXPO rc=%d\n", rc);
+		ZCRYPT_DBF_DBG("ioctl ICARSAMODEXPO rc=%d\n", rc);
 		return rc;
 	}
 	return put_user(mex.outputdatalength, &umex->outputdatalength);
@@ -1491,7 +1510,7 @@
 	if (rc == -EAGAIN && tr.again_counter >= TRACK_AGAIN_MAX)
 		rc = -EIO;
 	if (rc) {
-		ZCRYPT_DBF(DBF_DEBUG, "ioctl ICARSACRT rc=%d\n", rc);
+		ZCRYPT_DBF_DBG("ioctl ICARSACRT rc=%d\n", rc);
 		return rc;
 	}
 	return put_user(crt.outputdatalength, &ucrt->outputdatalength);
@@ -1509,12 +1528,12 @@
 		return -EFAULT;
 
 #ifdef CONFIG_ZCRYPT_DEBUG
-	if (xcRB.status & (1U << 31)) {
+	if ((xcRB.status & 0x8000FFFF) == 0x80004649 /* 'FI' */) {
 		if (!capable(CAP_SYS_ADMIN))
 			return -EPERM;
 		tr.fi.cmd = (u16)(xcRB.status >> 16);
 	}
-	xcRB.status &= 0x0000FFFF;
+	xcRB.status = 0;
 #endif
 
 	do {
@@ -1536,8 +1555,8 @@
 	if (rc == -EAGAIN && tr.again_counter >= TRACK_AGAIN_MAX)
 		rc = -EIO;
 	if (rc)
-		ZCRYPT_DBF(DBF_DEBUG, "ioctl ZSENDCPRB rc=%d status=0x%x\n",
-			   rc, xcRB.status);
+		ZCRYPT_DBF_DBG("ioctl ZSENDCPRB rc=%d status=0x%x\n",
+			       rc, xcRB.status);
 	if (copy_to_user(uxcRB, &xcRB, sizeof(xcRB)))
 		return -EFAULT;
 	return rc;
@@ -1582,7 +1601,7 @@
 	if (rc == -EAGAIN && tr.again_counter >= TRACK_AGAIN_MAX)
 		rc = -EIO;
 	if (rc)
-		ZCRYPT_DBF(DBF_DEBUG, "ioctl ZSENDEP11CPRB rc=%d\n", rc);
+		ZCRYPT_DBF_DBG("ioctl ZSENDEP11CPRB rc=%d\n", rc);
 	if (copy_to_user(uxcrb, &xcrb, sizeof(xcrb)))
 		return -EFAULT;
 	return rc;
@@ -1709,7 +1728,7 @@
 	}
 	/* unknown ioctl number */
 	default:
-		ZCRYPT_DBF(DBF_DEBUG, "unknown ioctl 0x%08x\n", cmd);
+		ZCRYPT_DBF_DBG("unknown ioctl 0x%08x\n", cmd);
 		return -ENOIOCTLCMD;
 	}
 }
@@ -2048,16 +2067,14 @@
 			break;
 		case -ETIME:
 			/* timeout */
-			ZCRYPT_DBF(DBF_WARN,
-				   "%s ap_wait_init_apqn_bindings_complete() returned with ETIME\n",
-				   __func__);
+			ZCRYPT_DBF_WARN("%s ap_wait_init_apqn_bindings_complete()=ETIME\n",
+					__func__);
 			zcrypt_wait_api_state = -ETIME;
 			break;
 		default:
 			/* other failure */
-			ZCRYPT_DBF(DBF_DEBUG,
-				   "%s ap_wait_init_apqn_bindings_complete() failure rc=%d\n",
-				   __func__, rc);
+			ZCRYPT_DBF_DBG("%s ap_wait_init_apqn_bindings_complete()=%d\n",
+				       __func__, rc);
 			break;
 		}
 		break;
@@ -2079,7 +2096,7 @@
 
 int __init zcrypt_debug_init(void)
 {
-	zcrypt_dbf_info = debug_register("zcrypt", 1, 1,
+	zcrypt_dbf_info = debug_register("zcrypt", 2, 1,
 					 DBF_MAX_SPRINTF_ARGS * sizeof(long));
 	debug_register_view(zcrypt_dbf_info, &debug_sprintf_view);
 	debug_set_level(zcrypt_dbf_info, DBF_ERR);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_card.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_card.c
@@ -76,7 +76,7 @@
 	zc->online = online;
 	id = zc->card->id;
 
-	ZCRYPT_DBF(DBF_INFO, "card=%02x online=%d\n", id, online);
+	ZCRYPT_DBF_INFO("%s card=%02x online=%d\n", __func__, id, online);
 
 	ap_send_online_uevent(&ac->ap_dev, online);
 
@@ -189,7 +189,8 @@
 
 	zc->online = 1;
 
-	ZCRYPT_DBF(DBF_INFO, "card=%02x register online=1\n", zc->card->id);
+	ZCRYPT_DBF_INFO("%s card=%02x register online=1\n",
+			__func__, zc->card->id);
 
 	rc = sysfs_create_group(&zc->card->ap_dev.device.kobj,
 				&zcrypt_card_attr_group);
@@ -211,7 +212,8 @@
  */
 void zcrypt_card_unregister(struct zcrypt_card *zc)
 {
-	ZCRYPT_DBF(DBF_INFO, "card=%02x unregister\n", zc->card->id);
+	ZCRYPT_DBF_INFO("%s card=%02x unregister\n",
+			__func__, zc->card->id);
 
 	spin_lock(&zcrypt_list_lock);
 	list_del_init(&zc->list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_cex4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_cex4.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- *  Copyright IBM Corp. 2012, 2019
+ *  Copyright IBM Corp. 2012, 2022
  *  Author(s): Holger Dengler <hd@linux.vnet.ibm.com>
  */
 
@@ -36,8 +36,8 @@
 #define CEX4_CLEANUP_TIME	(900*HZ)
 
 MODULE_AUTHOR("IBM Corporation");
-MODULE_DESCRIPTION("CEX4/CEX5/CEX6/CEX7 Cryptographic Card device driver, " \
-		   "Copyright IBM Corp. 2019");
+MODULE_DESCRIPTION("CEX[45678] Cryptographic Card device driver, " \
+		   "Copyright IBM Corp. 2022");
 MODULE_LICENSE("GPL");
 
 static struct ap_device_id zcrypt_cex4_card_ids[] = {
@@ -49,6 +49,8 @@
 	  .match_flags = AP_DEVICE_ID_MATCH_CARD_TYPE },
 	{ .dev_type = AP_DEVICE_TYPE_CEX7,
 	  .match_flags = AP_DEVICE_ID_MATCH_CARD_TYPE },
+	{ .dev_type = AP_DEVICE_TYPE_CEX8,
+	  .match_flags = AP_DEVICE_ID_MATCH_CARD_TYPE },
 	{ /* end of list */ },
 };
 
@@ -63,6 +65,8 @@
 	  .match_flags = AP_DEVICE_ID_MATCH_QUEUE_TYPE },
 	{ .dev_type = AP_DEVICE_TYPE_CEX7,
 	  .match_flags = AP_DEVICE_ID_MATCH_QUEUE_TYPE },
+	{ .dev_type = AP_DEVICE_TYPE_CEX8,
+	  .match_flags = AP_DEVICE_ID_MATCH_QUEUE_TYPE },
 	{ /* end of list */ },
 };
 
@@ -395,7 +399,7 @@
 };
 
 /*
- * Probe function for CEX4/CEX5/CEX6/CEX7 card device. It always
+ * Probe function for CEX[45678] card device. It always
  * accepts the AP device since the bus_match already checked
  * the hardware type.
  * @ap_dev: pointer to the AP device.
@@ -414,6 +418,8 @@
 		  6,   9,  20, 17,  65,	 438, 0, 0};
 	static const int CEX7A_SPEED_IDX[NUM_OPS] = {
 		  6,   8,  17, 15,  54,	 362, 0, 0};
+	static const int CEX8A_SPEED_IDX[NUM_OPS] = {
+		  6,   8,  17, 15,  54,	 362, 0, 0};
 
 	static const int CEX4C_SPEED_IDX[NUM_OPS] = {
 		 59,  69, 308, 83, 278, 2204, 209, 40};
@@ -423,6 +429,8 @@
 		 16,  20,  32, 27,  77,	 455,  24,  9};
 	static const int CEX7C_SPEED_IDX[NUM_OPS] = {
 		 14,  16,  26, 23,  64,	 376,  23,  8};
+	static const int CEX8C_SPEED_IDX[NUM_OPS] = {
+		 14,  16,  26, 23,  64,	 376,  23,  8};
 
 	static const int CEX4P_SPEED_IDX[NUM_OPS] = {
 		  0,   0,   0,	 0,   0,   0,	0,  50};
@@ -432,6 +440,8 @@
 		  0,   0,   0,	 0,   0,   0,	0,   9};
 	static const int CEX7P_SPEED_IDX[NUM_OPS] = {
 		  0,   0,   0,	 0,   0,   0,	0,   8};
+	static const int CEX8P_SPEED_IDX[NUM_OPS] = {
+		  0,   0,   0,	 0,   0,   0,	0,   8};
 
 	struct ap_card *ac = to_ap_card(&ap_dev->device);
 	struct zcrypt_card *zc;
@@ -455,13 +465,20 @@
 			zc->type_string = "CEX6A";
 			zc->user_space_type = ZCRYPT_CEX6;
 			zc->speed_rating = CEX6A_SPEED_IDX;
-		} else {
+		} else if (ac->ap_dev.device_type == AP_DEVICE_TYPE_CEX7) {
 			zc->type_string = "CEX7A";
+			zc->speed_rating = CEX7A_SPEED_IDX;
+			/* wrong user space type, just for compatibility
+			 * with the ZCRYPT_STATUS_MASK ioctl.
+			 */
+			zc->user_space_type = ZCRYPT_CEX6;
+		} else {
+			zc->type_string = "CEX8A";
+			zc->speed_rating = CEX8A_SPEED_IDX;
 			/* wrong user space type, just for compatibility
 			 * with the ZCRYPT_STATUS_MASK ioctl.
 			 */
 			zc->user_space_type = ZCRYPT_CEX6;
-			zc->speed_rating = CEX7A_SPEED_IDX;
 		}
 		zc->min_mod_size = CEX4A_MIN_MOD_SIZE;
 		if (ap_test_bit(&ac->functions, AP_FUNC_MEX4K) &&
@@ -477,32 +494,39 @@
 	} else if (ap_test_bit(&ac->functions, AP_FUNC_COPRO)) {
 		if (ac->ap_dev.device_type == AP_DEVICE_TYPE_CEX4) {
 			zc->type_string = "CEX4C";
-			/* wrong user space type, must be CEX4
+			zc->speed_rating = CEX4C_SPEED_IDX;
+			/* wrong user space type, must be CEX3C
 			 * just keep it for cca compatibility
 			 */
 			zc->user_space_type = ZCRYPT_CEX3C;
-			zc->speed_rating = CEX4C_SPEED_IDX;
 		} else if (ac->ap_dev.device_type == AP_DEVICE_TYPE_CEX5) {
 			zc->type_string = "CEX5C";
-			/* wrong user space type, must be CEX5
+			zc->speed_rating = CEX5C_SPEED_IDX;
+			/* wrong user space type, must be CEX3C
 			 * just keep it for cca compatibility
 			 */
 			zc->user_space_type = ZCRYPT_CEX3C;
-			zc->speed_rating = CEX5C_SPEED_IDX;
 		} else if (ac->ap_dev.device_type == AP_DEVICE_TYPE_CEX6) {
 			zc->type_string = "CEX6C";
-			/* wrong user space type, must be CEX6
+			zc->speed_rating = CEX6C_SPEED_IDX;
+			/* wrong user space type, must be CEX3C
 			 * just keep it for cca compatibility
 			 */
 			zc->user_space_type = ZCRYPT_CEX3C;
-			zc->speed_rating = CEX6C_SPEED_IDX;
-		} else {
+		} else if (ac->ap_dev.device_type == AP_DEVICE_TYPE_CEX7) {
 			zc->type_string = "CEX7C";
-			/* wrong user space type, must be CEX7
+			zc->speed_rating = CEX7C_SPEED_IDX;
+			/* wrong user space type, must be CEX3C
+			 * just keep it for cca compatibility
+			 */
+			zc->user_space_type = ZCRYPT_CEX3C;
+		} else {
+			zc->type_string = "CEX8C";
+			zc->speed_rating = CEX8C_SPEED_IDX;
+			/* wrong user space type, must be CEX3C
 			 * just keep it for cca compatibility
 			 */
 			zc->user_space_type = ZCRYPT_CEX3C;
-			zc->speed_rating = CEX7C_SPEED_IDX;
 		}
 		zc->min_mod_size = CEX4C_MIN_MOD_SIZE;
 		zc->max_mod_size = CEX4C_MAX_MOD_SIZE;
@@ -520,13 +544,20 @@
 			zc->type_string = "CEX6P";
 			zc->user_space_type = ZCRYPT_CEX6;
 			zc->speed_rating = CEX6P_SPEED_IDX;
-		} else {
+		} else if (ac->ap_dev.device_type == AP_DEVICE_TYPE_CEX7) {
 			zc->type_string = "CEX7P";
+			zc->speed_rating = CEX7P_SPEED_IDX;
+			/* wrong user space type, just for compatibility
+			 * with the ZCRYPT_STATUS_MASK ioctl.
+			 */
+			zc->user_space_type = ZCRYPT_CEX6;
+		} else {
+			zc->type_string = "CEX8P";
+			zc->speed_rating = CEX8P_SPEED_IDX;
 			/* wrong user space type, just for compatibility
 			 * with the ZCRYPT_STATUS_MASK ioctl.
 			 */
 			zc->user_space_type = ZCRYPT_CEX6;
-			zc->speed_rating = CEX7P_SPEED_IDX;
 		}
 		zc->min_mod_size = CEX4C_MIN_MOD_SIZE;
 		zc->max_mod_size = CEX4C_MAX_MOD_SIZE;
@@ -563,7 +594,7 @@
 }
 
 /*
- * This is called to remove the CEX4/CEX5/CEX6/CEX7 card driver
+ * This is called to remove the CEX[45678] card driver
  * information if an AP card device is removed.
  */
 static void zcrypt_cex4_card_remove(struct ap_device *ap_dev)
@@ -587,7 +618,7 @@
 };
 
 /*
- * Probe function for CEX4/CEX5/CEX6/CEX7 queue device. It always
+ * Probe function for CEX[45678] queue device. It always
  * accepts the AP device since the bus_match already checked
  * the hardware type.
  * @ap_dev: pointer to the AP device.
@@ -653,7 +684,7 @@
 }
 
 /*
- * This is called to remove the CEX4/CEX5/CEX6/CEX7 queue driver
+ * This is called to remove the CEX[45678] queue driver
  * information if an AP queue device is removed.
  */
 static void zcrypt_cex4_queue_remove(struct ap_device *ap_dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_debug.h
@@ -17,7 +17,7 @@
 #define RC2ERR(rc) ((rc) ? DBF_ERR : DBF_INFO)
 #define RC2WARN(rc) ((rc) ? DBF_WARN : DBF_INFO)
 
-#define DBF_MAX_SPRINTF_ARGS 5
+#define DBF_MAX_SPRINTF_ARGS 6
 
 #define ZCRYPT_DBF(...)					\
 	debug_sprintf_event(zcrypt_dbf_info, ##__VA_ARGS__)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_ep11misc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_ep11misc.c
@@ -788,7 +788,7 @@
 	kb->head.type = TOKTYPE_NON_CCA;
 	kb->head.len = rep_pl->data_len;
 	kb->head.version = TOKVER_EP11_AES;
-	kb->head.keybitlen = keybitsize;
+	kb->head.bitlen = keybitsize;
 
 out:
 	kfree(req);
@@ -1056,7 +1056,7 @@
 	kb->head.type = TOKTYPE_NON_CCA;
 	kb->head.len = rep_pl->data_len;
 	kb->head.version = TOKVER_EP11_AES;
-	kb->head.keybitlen = keybitsize;
+	kb->head.bitlen = keybitsize;
 
 out:
 	kfree(req);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_ep11misc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_ep11misc.h
@@ -29,14 +29,7 @@
 	union {
 		u8 session[32];
 		/* only used for PKEY_TYPE_EP11: */
-		struct {
-			u8  type;      /* 0x00 (TOKTYPE_NON_CCA) */
-			u8  res0;      /* unused */
-			u16 len;       /* total length in bytes of this blob */
-			u8  version;   /* 0x03 (TOKVER_EP11_AES) */
-			u8  res1;      /* unused */
-			u16 keybitlen; /* clear key bit len, 0 for unknown */
-		} head;
+		struct ep11kblob_header head;
 	};
 	u8  wkvp[16];  /* wrapping key verification pattern */
 	u64 attr;      /* boolean key attributes */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_error.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_error.h
@@ -98,9 +98,8 @@
 	case REP88_ERROR_MESSAGE_MALFORMD:	 /* 0x22 */
 	case REP88_ERROR_KEY_TYPE:		 /* 0x34 */
 		/* RY indicates malformed request */
-		ZCRYPT_DBF(DBF_WARN,
-			   "dev=%02x.%04x RY=0x%02x => rc=EINVAL\n",
-			   card, queue, ehdr->reply_code);
+		ZCRYPT_DBF_WARN("%s dev=%02x.%04x RY=0x%02x => rc=EINVAL\n",
+				__func__, card, queue, ehdr->reply_code);
 		return -EINVAL;
 	case REP82_ERROR_MACHINE_FAILURE:	 /* 0x10 */
 	case REP82_ERROR_MESSAGE_TYPE:		 /* 0x20 */
@@ -119,19 +118,18 @@
 			} __packed * head = reply->msg;
 			unsigned int apfs = *((u32 *)head->fmt2.apfs);
 
-			ZCRYPT_DBF(DBF_WARN,
-				   "dev=%02x.%04x RY=0x%02x apfs=0x%x => bus rescan, rc=EAGAIN\n",
-				   card, queue, ehdr->reply_code, apfs);
+			ZCRYPT_DBF_WARN(
+				"%s dev=%02x.%04x RY=0x%02x apfs=0x%x => bus rescan, rc=EAGAIN\n",
+				__func__, card, queue, ehdr->reply_code, apfs);
 		} else
-			ZCRYPT_DBF(DBF_WARN,
-				   "dev=%02x.%04x RY=0x%02x => bus rescan, rc=EAGAIN\n",
-				   card, queue, ehdr->reply_code);
+			ZCRYPT_DBF_WARN("%s dev=%02x.%04x RY=0x%02x => bus rescan, rc=EAGAIN\n",
+					__func__, card, queue,
+					ehdr->reply_code);
 		return -EAGAIN;
 	default:
 		/* Assume request is valid and a retry will be worth it */
-		ZCRYPT_DBF(DBF_WARN,
-			   "dev=%02x.%04x RY=0x%02x => rc=EAGAIN\n",
-			   card, queue, ehdr->reply_code);
+		ZCRYPT_DBF_WARN("%s dev=%02x.%04x RY=0x%02x => rc=EAGAIN\n",
+				__func__, card, queue, ehdr->reply_code);
 		return -EAGAIN;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_msgtype50.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_msgtype50.c
@@ -156,7 +156,7 @@
 	unsigned char	reserved3[8];
 } __packed;
 
-unsigned int get_rsa_modex_fc(struct ica_rsa_modexpo *mex, int *fcode)
+int get_rsa_modex_fc(struct ica_rsa_modexpo *mex, int *fcode)
 {
 
 	if (!mex->inputdatalength)
@@ -172,7 +172,7 @@
 	return 0;
 }
 
-unsigned int get_rsa_crt_fc(struct ica_rsa_modexpo_crt *crt, int *fcode)
+int get_rsa_crt_fc(struct ica_rsa_modexpo_crt *crt, int *fcode)
 {
 
 	if (!crt->inputdatalength)
@@ -369,12 +369,10 @@
 		zq->online = 0;
 		pr_err("Crypto dev=%02x.%04x code=0x%02x => online=0 rc=EAGAIN\n",
 		       AP_QID_CARD(zq->queue->qid),
-		       AP_QID_QUEUE(zq->queue->qid),
-		       t80h->code);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x code=0x%02x => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
-			       AP_QID_QUEUE(zq->queue->qid),
-			       t80h->code);
+		       AP_QID_QUEUE(zq->queue->qid), t80h->code);
+		ZCRYPT_DBF_ERR("%s dev=%02x.%04x code=0x%02x => online=0 rc=EAGAIN\n",
+			       __func__, AP_QID_CARD(zq->queue->qid),
+			       AP_QID_QUEUE(zq->queue->qid), t80h->code);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
 		return -EAGAIN;
 	}
@@ -409,10 +407,10 @@
 		       AP_QID_CARD(zq->queue->qid),
 		       AP_QID_QUEUE(zq->queue->qid),
 		       (int) rtype);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
-			       AP_QID_QUEUE(zq->queue->qid),
-			       (int) rtype);
+		ZCRYPT_DBF_ERR(
+			"%s dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid), (int) rtype);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
 		return -EAGAIN;
 	}
@@ -499,6 +497,10 @@
 		ap_cancel_message(zq->queue, ap_msg);
 out:
 	ap_msg->private = NULL;
+	if (rc)
+		ZCRYPT_DBF_DBG("%s send me cprb at dev=%02x.%04x rc=%d\n",
+			       __func__, AP_QID_CARD(zq->queue->qid),
+			       AP_QID_QUEUE(zq->queue->qid), rc);
 	return rc;
 }
 
@@ -544,6 +546,10 @@
 		ap_cancel_message(zq->queue, ap_msg);
 out:
 	ap_msg->private = NULL;
+	if (rc)
+		ZCRYPT_DBF_DBG("%s send crt cprb at dev=%02x.%04x rc=%d\n",
+			       __func__, AP_QID_CARD(zq->queue->qid),
+			       AP_QID_QUEUE(zq->queue->qid), rc);
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_msgtype50.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_msgtype50.h
@@ -20,8 +20,8 @@
 
 #define MSGTYPE_ADJUSTMENT 0x08  /* type04 extension (not needed in type50) */
 
-unsigned int get_rsa_modex_fc(struct ica_rsa_modexpo *, int *);
-unsigned int get_rsa_crt_fc(struct ica_rsa_modexpo_crt *, int *);
+int get_rsa_modex_fc(struct ica_rsa_modexpo *mex, int *fc);
+int get_rsa_crt_fc(struct ica_rsa_modexpo_crt *crt, int *fc);
 
 void zcrypt_msgtype50_init(void);
 void zcrypt_msgtype50_exit(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_msgtype6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_msgtype6.c
@@ -472,6 +472,7 @@
 	*fcode = (msg->hdr.function_code[0] << 8) | msg->hdr.function_code[1];
 	*dom = (unsigned short *)&msg->cprbx.domain;
 
+	/* check subfunction, US and AU need special flag with NQAP */
 	if (memcmp(function_code, "US", 2) == 0
 	    || memcmp(function_code, "AU", 2) == 0)
 		ap_msg->flags |= AP_MSG_FLAG_SPECIAL;
@@ -481,6 +482,23 @@
 		ap_msg->flags ^= AP_MSG_FLAG_SPECIAL;
 #endif
 
+	/* check CPRB minor version, set info bits in ap_message flag field */
+	switch (*(unsigned short *)(&msg->cprbx.func_id[0])) {
+	case 0x5432: /* "T2" */
+		ap_msg->flags |= AP_MSG_FLAG_USAGE;
+		break;
+	case 0x5433: /* "T3" */
+	case 0x5435: /* "T5" */
+	case 0x5436: /* "T6" */
+	case 0x5437: /* "T7" */
+		ap_msg->flags |= AP_MSG_FLAG_ADMIN;
+		break;
+	default:
+		ZCRYPT_DBF_DBG("%s unknown CPRB minor version '%c%c'\n",
+			       __func__, msg->cprbx.func_id[0],
+			       msg->cprbx.func_id[1]);
+	}
+
 	/* copy data block */
 	if (xcRB->request_data_length &&
 	    z_copy_from_user(userspace, req_data, xcRB->request_data_address,
@@ -492,7 +510,8 @@
 
 static int xcrb_msg_to_type6_ep11cprb_msgx(bool userspace, struct ap_message *ap_msg,
 					   struct ep11_urb *xcRB,
-					   unsigned int *fcode)
+					   unsigned int *fcode,
+					   unsigned int *domain)
 {
 	unsigned int lfmt;
 	static struct type6_hdr static_type6_ep11_hdr = {
@@ -568,6 +587,14 @@
 		ap_msg->flags ^= AP_MSG_FLAG_SPECIAL;
 #endif
 
+	/* set info bits in ap_message flag field */
+	if (msg->cprbx.flags & 0x80)
+		ap_msg->flags |= AP_MSG_FLAG_ADMIN;
+	else
+		ap_msg->flags |= AP_MSG_FLAG_USAGE;
+
+	*domain = msg->cprbx.target_id;
+
 	return 0;
 }
 
@@ -649,8 +676,8 @@
 		    (service_rc == 8 && service_rs == 72) ||
 		    (service_rc == 8 && service_rs == 770) ||
 		    (service_rc == 12 && service_rs == 769)) {
-			ZCRYPT_DBF_WARN("dev=%02x.%04x rc/rs=%d/%d => rc=EINVAL\n",
-					AP_QID_CARD(zq->queue->qid),
+			ZCRYPT_DBF_WARN("%s dev=%02x.%04x rc/rs=%d/%d => rc=EINVAL\n",
+					__func__, AP_QID_CARD(zq->queue->qid),
 					AP_QID_QUEUE(zq->queue->qid),
 					(int) service_rc, (int) service_rs);
 			return -EINVAL;
@@ -660,8 +687,8 @@
 		       AP_QID_CARD(zq->queue->qid),
 		       AP_QID_QUEUE(zq->queue->qid),
 		       (int) service_rc, (int) service_rs);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x rc/rs=%d/%d => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
+		ZCRYPT_DBF_ERR("%s dev=%02x.%04x rc/rs=%d/%d => online=0 rc=EAGAIN\n",
+			       __func__, AP_QID_CARD(zq->queue->qid),
 			       AP_QID_QUEUE(zq->queue->qid),
 			       (int) service_rc, (int) service_rs);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
@@ -714,17 +741,31 @@
 	char *data = reply->msg;
 
 	/* Copy CPRB to user */
+	if (xcRB->reply_control_blk_length < msg->fmt2.count1) {
+		ZCRYPT_DBF_DBG("%s reply_control_blk_length %u < required %u => EMSGSIZE\n",
+			       __func__, xcRB->reply_control_blk_length,
+			       msg->fmt2.count1);
+		return -EMSGSIZE;
+	}
 	if (z_copy_to_user(userspace, xcRB->reply_control_blk_addr,
 			   data + msg->fmt2.offset1, msg->fmt2.count1))
 		return -EFAULT;
 	xcRB->reply_control_blk_length = msg->fmt2.count1;
 
 	/* Copy data buffer to user */
-	if (msg->fmt2.count2)
+	if (msg->fmt2.count2) {
+		if (xcRB->reply_data_length < msg->fmt2.count2) {
+			ZCRYPT_DBF_DBG("%s reply_data_length %u < required %u => EMSGSIZE\n",
+				       __func__, xcRB->reply_data_length,
+				       msg->fmt2.count2);
+			return -EMSGSIZE;
+		}
 		if (z_copy_to_user(userspace, xcRB->reply_data_addr,
 				   data + msg->fmt2.offset2, msg->fmt2.count2))
 			return -EFAULT;
+	}
 	xcRB->reply_data_length = msg->fmt2.count2;
+
 	return 0;
 }
 
@@ -744,8 +785,12 @@
 	struct type86_fmt2_msg *msg = reply->msg;
 	char *data = reply->msg;
 
-	if (xcRB->resp_len < msg->fmt2.count1)
-		return -EINVAL;
+	if (xcRB->resp_len < msg->fmt2.count1) {
+		ZCRYPT_DBF_DBG("%s resp_len %u < required %u => EMSGSIZE\n",
+			       __func__, (unsigned int)xcRB->resp_len,
+			       msg->fmt2.count1);
+		return -EMSGSIZE;
+	}
 
 	/* Copy response CPRB to user */
 	if (z_copy_to_user(userspace, (char __force __user *)xcRB->resp,
@@ -806,10 +851,10 @@
 		       AP_QID_CARD(zq->queue->qid),
 		       AP_QID_QUEUE(zq->queue->qid),
 		       (int) msg->hdr.type);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
-			       AP_QID_QUEUE(zq->queue->qid),
-			       (int) msg->hdr.type);
+		ZCRYPT_DBF_ERR(
+			"%s dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid), (int) msg->hdr.type);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
 		return -EAGAIN;
 	}
@@ -841,10 +886,10 @@
 		       AP_QID_CARD(zq->queue->qid),
 		       AP_QID_QUEUE(zq->queue->qid),
 		       (int) msg->hdr.type);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
-			       AP_QID_QUEUE(zq->queue->qid),
-			       (int) msg->hdr.type);
+		ZCRYPT_DBF_ERR(
+			"%s dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid), (int) msg->hdr.type);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
 		return -EAGAIN;
 	}
@@ -871,10 +916,10 @@
 		       AP_QID_CARD(zq->queue->qid),
 		       AP_QID_QUEUE(zq->queue->qid),
 		       (int) msg->hdr.type);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
-			       AP_QID_QUEUE(zq->queue->qid),
-			       (int) msg->hdr.type);
+		ZCRYPT_DBF_ERR(
+			"%s dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid), (int) msg->hdr.type);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
 		return -EAGAIN;
 	}
@@ -902,10 +947,10 @@
 		       AP_QID_CARD(zq->queue->qid),
 		       AP_QID_QUEUE(zq->queue->qid),
 		       (int) msg->hdr.type);
-		ZCRYPT_DBF_ERR("dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
-			       AP_QID_CARD(zq->queue->qid),
-			       AP_QID_QUEUE(zq->queue->qid),
-			       (int) msg->hdr.type);
+		ZCRYPT_DBF_ERR(
+			"%s dev=%02x.%04x unknown response type 0x%02x => online=0 rc=EAGAIN\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid), (int) msg->hdr.type);
 		ap_send_online_uevent(&zq->queue->ap_dev, zq->online);
 		return -EAGAIN;
 	}
@@ -1113,15 +1158,17 @@
 }
 
 /*
- * Fetch function code from cprb.
- * Extracting the fc requires to copy the cprb from userspace.
- * So this function allocates memory and needs an ap_msg prepared
+ * Prepare a CCA AP msg request.
+ * Prepare a CCA AP msg: fetch the required data from userspace,
+ * prepare the AP msg, fill some info into the ap_message struct,
+ * extract some data from the CPRB and give back to the caller.
+ * This function allocates memory and needs an ap_msg prepared
  * by the caller with ap_init_message(). Also the caller has to
  * make sure ap_release_message() is always called even on failure.
  */
-unsigned int get_cprb_fc(bool userspace, struct ica_xcRB *xcRB,
-			 struct ap_message *ap_msg,
-			 unsigned int *func_code, unsigned short **dom)
+int prep_cca_ap_msg(bool userspace, struct ica_xcRB *xcRB,
+		    struct ap_message *ap_msg,
+		    unsigned int *func_code, unsigned short **dom)
 {
 	struct response_type resp_type = {
 		.type = CEXXC_RESPONSE_TYPE_XCRB,
@@ -1153,6 +1200,21 @@
 {
 	int rc;
 	struct response_type *rtype = (struct response_type *)(ap_msg->private);
+	struct {
+		struct type6_hdr hdr;
+		struct CPRBX cprbx;
+		/* ... more data blocks ... */
+	} __packed * msg = ap_msg->msg;
+
+	/*
+	 * Set the queue's reply buffer length minus 128 byte padding
+	 * as reply limit for the card firmware.
+	 */
+	msg->hdr.FromCardLen1 = min_t(unsigned int, msg->hdr.FromCardLen1,
+				      zq->reply.bufsize - 128);
+	if (msg->hdr.FromCardLen2)
+		msg->hdr.FromCardLen2 =
+			zq->reply.bufsize - msg->hdr.FromCardLen1 - 128;
 
 	init_completion(&rtype->work);
 	rc = ap_queue_message(zq->queue, ap_msg);
@@ -1167,19 +1229,25 @@
 		/* Signal pending. */
 		ap_cancel_message(zq->queue, ap_msg);
 out:
+	if (rc)
+		ZCRYPT_DBF_DBG("%s send cprb at dev=%02x.%04x rc=%d\n",
+			       __func__, AP_QID_CARD(zq->queue->qid),
+			       AP_QID_QUEUE(zq->queue->qid), rc);
 	return rc;
 }
 
 /*
- * Fetch function code from ep11 cprb.
- * Extracting the fc requires to copy the ep11 cprb from userspace.
- * So this function allocates memory and needs an ap_msg prepared
+ * Prepare an EP11 AP msg request.
+ * Prepare an EP11 AP msg: fetch the required data from userspace,
+ * prepare the AP msg, fill some info into the ap_message struct,
+ * extract some data from the CPRB and give back to the caller.
+ * This function allocates memory and needs an ap_msg prepared
  * by the caller with ap_init_message(). Also the caller has to
  * make sure ap_release_message() is always called even on failure.
  */
-unsigned int get_ep11cprb_fc(bool userspace, struct ep11_urb *xcrb,
-			     struct ap_message *ap_msg,
-			     unsigned int *func_code)
+int prep_ep11_ap_msg(bool userspace, struct ep11_urb *xcrb,
+		     struct ap_message *ap_msg,
+		     unsigned int *func_code, unsigned int *domain)
 {
 	struct response_type resp_type = {
 		.type = CEXXC_RESPONSE_TYPE_EP11,
@@ -1195,7 +1263,8 @@
 	ap_msg->private = kmemdup(&resp_type, sizeof(resp_type), GFP_KERNEL);
 	if (!ap_msg->private)
 		return -ENOMEM;
-	return xcrb_msg_to_type6_ep11cprb_msgx(userspace, ap_msg, xcrb, func_code);
+	return xcrb_msg_to_type6_ep11cprb_msgx(userspace, ap_msg, xcrb,
+					       func_code, domain);
 }
 
 /*
@@ -1227,7 +1296,6 @@
 		unsigned int	dom_val;	/* domain id	   */
 	} __packed * payload_hdr = NULL;
 
-
 	/*
 	 * The target domain field within the cprb body/payload block will be
 	 * replaced by the usage domain for non-management commands only.
@@ -1259,6 +1327,13 @@
 					AP_QID_QUEUE(zq->queue->qid);
 	}
 
+	/*
+	 * Set the queue's reply buffer length minus the two prepend headers
+	 * as reply limit for the card firmware.
+	 */
+	msg->hdr.FromCardLen1 = zq->reply.bufsize -
+		sizeof(struct type86_hdr) - sizeof(struct type86_fmt2_ext);
+
 	init_completion(&rtype->work);
 	rc = ap_queue_message(zq->queue, ap_msg);
 	if (rc)
@@ -1272,11 +1347,15 @@
 		/* Signal pending. */
 		ap_cancel_message(zq->queue, ap_msg);
 out:
+	if (rc)
+		ZCRYPT_DBF_DBG("%s send cprb at dev=%02x.%04x rc=%d\n",
+			       __func__, AP_QID_CARD(zq->queue->qid),
+			       AP_QID_QUEUE(zq->queue->qid), rc);
 	return rc;
 }
 
-unsigned int get_rng_fc(struct ap_message *ap_msg, int *func_code,
-						   unsigned int *domain)
+int prep_rng_ap_msg(struct ap_message *ap_msg, int *func_code,
+		    unsigned int *domain)
 {
 	struct response_type resp_type = {
 		.type = CEXXC_RESPONSE_TYPE_XCRB,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_msgtype6.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_msgtype6.h
@@ -94,11 +94,14 @@
 	unsigned int	  offset4;	/* 0x00000000			*/
 } __packed;
 
-unsigned int get_cprb_fc(bool userspace, struct ica_xcRB *, struct ap_message *,
-			 unsigned int *, unsigned short **);
-unsigned int get_ep11cprb_fc(bool userspace, struct ep11_urb *, struct ap_message *,
-			     unsigned int *);
-unsigned int get_rng_fc(struct ap_message *, int *, unsigned int *);
+int prep_cca_ap_msg(bool userspace, struct ica_xcRB *xcrb,
+		    struct ap_message *ap_msg,
+		    unsigned int *fc, unsigned short **dom);
+int prep_ep11_ap_msg(bool userspace, struct ep11_urb *xcrb,
+		     struct ap_message *ap_msg,
+		     unsigned int *fc, unsigned int *dom);
+int prep_rng_ap_msg(struct ap_message *ap_msg,
+		    int *fc, unsigned int *dom);
 
 #define LOW	10
 #define MEDIUM	100
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/crypto/zcrypt_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/crypto/zcrypt_queue.c
@@ -65,10 +65,9 @@
 		return -EINVAL;
 	zq->online = online;
 
-	ZCRYPT_DBF(DBF_INFO, "queue=%02x.%04x online=%d\n",
-		   AP_QID_CARD(zq->queue->qid),
-		   AP_QID_QUEUE(zq->queue->qid),
-		   online);
+	ZCRYPT_DBF_INFO("%s queue=%02x.%04x online=%d\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid), online);
 
 	ap_send_online_uevent(&aq->ap_dev, online);
 
@@ -175,8 +174,9 @@
 	zq->zcard = zc;
 	zq->online = 1;	/* New devices are online by default. */
 
-	ZCRYPT_DBF(DBF_INFO, "queue=%02x.%04x register online=1\n",
-		   AP_QID_CARD(zq->queue->qid), AP_QID_QUEUE(zq->queue->qid));
+	ZCRYPT_DBF_INFO("%s queue=%02x.%04x register online=1\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid));
 
 	list_add_tail(&zq->list, &zc->zqueues);
 	spin_unlock(&zcrypt_list_lock);
@@ -215,8 +215,9 @@
 {
 	struct zcrypt_card *zc;
 
-	ZCRYPT_DBF(DBF_INFO, "queue=%02x.%04x unregister\n",
-		   AP_QID_CARD(zq->queue->qid), AP_QID_QUEUE(zq->queue->qid));
+	ZCRYPT_DBF_INFO("%s queue=%02x.%04x unregister\n",
+			__func__, AP_QID_CARD(zq->queue->qid),
+			AP_QID_QUEUE(zq->queue->qid));
 
 	zc = zq->zcard;
 	spin_lock(&zcrypt_list_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/ctcm_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/ctcm_main.c
@@ -825,16 +825,9 @@
 /**
  * Start transmission of a packet.
  * Called from generic network device layer.
- *
- *  skb		Pointer to buffer containing the packet.
- *  dev		Pointer to interface struct.
- *
- * returns 0 if packet consumed, !0 if packet rejected.
- *         Note: If we return !0, then the packet is free'd by
- *               the generic network layer.
  */
 /* first merge version - leaving both functions separated */
-static int ctcm_tx(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t ctcm_tx(struct sk_buff *skb, struct net_device *dev)
 {
 	struct ctcm_priv *priv = dev->ml_priv;
 
@@ -877,7 +870,7 @@
 }
 
 /* unmerged MPC variant of ctcm_tx */
-static int ctcmpc_tx(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t ctcmpc_tx(struct sk_buff *skb, struct net_device *dev)
 {
 	int len = 0;
 	struct ctcm_priv *priv = dev->ml_priv;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/ctcm_mpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/ctcm_mpc.c
@@ -626,8 +626,6 @@
 		ctcm_clear_busy_do(dev);
 	}
 
-	kfree(mpcginfo);
-
 	return;
 
 }
@@ -1192,10 +1190,10 @@
 						CTCM_FUNTAIL, dev->name);
 			priv->stats.rx_dropped++;
 			/* mpcginfo only used for non-data transfers */
-			kfree(mpcginfo);
 			if (do_debug_data)
 				ctcmpc_dump_skb(pskb, -8);
 		}
+		kfree(mpcginfo);
 	}
 done:
 
@@ -1977,7 +1975,6 @@
 		}
 		break;
 	}
-	kfree(mpcginfo);
 
 	CTCM_PR_DEBUG("ctcmpc:%s() %s xid2:%i xid7:%i xidt_p2:%i \n",
 		__func__, ch->id, grp->outstanding_xid2,
@@ -2038,7 +2035,6 @@
 		mpc_validate_xid(mpcginfo);
 		break;
 	}
-	kfree(mpcginfo);
 	return;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/ctcm_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/ctcm_sysfs.c
@@ -39,11 +39,12 @@
 	struct ctcm_priv *priv = dev_get_drvdata(dev);
 	int rc;
 
-	ndev = priv->channel[CTCM_READ]->netdev;
-	if (!(priv && priv->channel[CTCM_READ] && ndev)) {
+	if (!(priv && priv->channel[CTCM_READ] &&
+	      priv->channel[CTCM_READ]->netdev)) {
 		CTCM_DBF_TEXT(SETUP, CTC_DBF_ERROR, "bfnondev");
 		return -ENODEV;
 	}
+	ndev = priv->channel[CTCM_READ]->netdev;
 
 	rc = kstrtouint(buf, 0, &bs1);
 	if (rc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/lcs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/lcs.c
@@ -1518,9 +1518,8 @@
 /**
  * Packet transmit function called by network stack
  */
-static int
-__lcs_start_xmit(struct lcs_card *card, struct sk_buff *skb,
-		 struct net_device *dev)
+static netdev_tx_t __lcs_start_xmit(struct lcs_card *card, struct sk_buff *skb,
+				    struct net_device *dev)
 {
 	struct lcs_header *header;
 	int rc = NETDEV_TX_OK;
@@ -1581,8 +1580,7 @@
 	return rc;
 }
 
-static int
-lcs_start_xmit(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t lcs_start_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct lcs_card *card;
 	int rc;
@@ -1735,10 +1733,11 @@
 			lcs_schedule_recovery(card);
 			break;
 		case LCS_CMD_STOPLAN:
-			pr_warn("Stoplan for %s initiated by LGW\n",
-				card->dev->name);
-			if (card->dev)
+			if (card->dev) {
+				pr_warn("Stoplan for %s initiated by LGW\n",
+					card->dev->name);
 				netif_carrier_off(card->dev);
+			}
 			break;
 		default:
 			LCS_DBF_TEXT(5, trace, "noLGWcmd");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/netiucv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/netiucv.c
@@ -1252,15 +1252,8 @@
 /**
  * Start transmission of a packet.
  * Called from generic network device layer.
- *
- * @param skb Pointer to buffer containing the packet.
- * @param dev Pointer to interface struct.
- *
- * @return 0 if packet consumed, !0 if packet rejected.
- *         Note: If we return !0, then the packet is free'd by
- *               the generic network layer.
  */
-static int netiucv_tx(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t netiucv_tx(struct sk_buff *skb, struct net_device *dev)
 {
 	struct netiucv_priv *privptr = netdev_priv(dev);
 	int rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/qeth_core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/qeth_core.h
@@ -545,7 +545,6 @@
 struct qeth_qdio_info {
 	atomic_t state;
 	/* input */
-	int no_in_queues;
 	struct qeth_qdio_q *in_q;
 	struct qeth_qdio_q *c_q;
 	struct qeth_qdio_buffer_pool in_buf_pool;
@@ -717,7 +716,6 @@
 	u16 chid;
 	u8 ids_valid:1; /* cssid,iid,chid */
 	u8 dev_addr_is_registered:1;
-	u8 open_when_online:1;
 	u8 promisc_mode:1;
 	u8 use_v1_blkt:1;
 	u8 is_vm_nic:1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/qeth_core_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/qeth_core_main.c
@@ -354,8 +354,8 @@
 		qdio_reset_buffers(card->qdio.c_q->qdio_bufs,
 				   QDIO_MAX_BUFFERS_PER_Q);
 		card->qdio.c_q->next_buf_to_init = 127;
-		rc = do_QDIO(CARD_DDEV(card), QDIO_FLAG_SYNC_INPUT,
-			     card->qdio.no_in_queues - 1, 0, 127, NULL);
+		rc = do_QDIO(CARD_DDEV(card), QDIO_FLAG_SYNC_INPUT, 1, 0, 127,
+			     NULL);
 		if (rc) {
 			QETH_CARD_TEXT_(card, 2, "1err%d", rc);
 			goto out;
@@ -366,35 +366,33 @@
 	return rc;
 }
 
+static void qeth_free_cq(struct qeth_card *card)
+{
+	if (card->qdio.c_q) {
+		qeth_free_qdio_queue(card->qdio.c_q);
+		card->qdio.c_q = NULL;
+	}
+}
+
 static int qeth_alloc_cq(struct qeth_card *card)
 {
 	if (card->options.cq == QETH_CQ_ENABLED) {
 		QETH_CARD_TEXT(card, 2, "cqon");
-		card->qdio.c_q = qeth_alloc_qdio_queue();
 		if (!card->qdio.c_q) {
-			dev_err(&card->gdev->dev, "Failed to create completion queue\n");
-			return -ENOMEM;
+			card->qdio.c_q = qeth_alloc_qdio_queue();
+			if (!card->qdio.c_q) {
+				dev_err(&card->gdev->dev,
+					"Failed to create completion queue\n");
+				return -ENOMEM;
+			}
 		}
-
-		card->qdio.no_in_queues = 2;
 	} else {
 		QETH_CARD_TEXT(card, 2, "nocq");
-		card->qdio.c_q = NULL;
-		card->qdio.no_in_queues = 1;
+		qeth_free_cq(card);
 	}
-	QETH_CARD_TEXT_(card, 2, "iqc%d", card->qdio.no_in_queues);
 	return 0;
 }
 
-static void qeth_free_cq(struct qeth_card *card)
-{
-	if (card->qdio.c_q) {
-		--card->qdio.no_in_queues;
-		qeth_free_qdio_queue(card->qdio.c_q);
-		card->qdio.c_q = NULL;
-	}
-}
-
 static enum iucv_tx_notify qeth_compute_cq_notification(int sbalf15,
 							int delayed)
 {
@@ -770,6 +768,49 @@
 				 ipa_name, com, CARD_DEVID(card));
 }
 
+static void qeth_default_link_info(struct qeth_card *card)
+{
+	struct qeth_link_info *link_info = &card->info.link_info;
+
+	QETH_CARD_TEXT(card, 2, "dftlinfo");
+	link_info->duplex = DUPLEX_FULL;
+
+	if (IS_IQD(card) || IS_VM_NIC(card)) {
+		link_info->speed = SPEED_10000;
+		link_info->port = PORT_FIBRE;
+		link_info->link_mode = QETH_LINK_MODE_FIBRE_SHORT;
+	} else {
+		switch (card->info.link_type) {
+		case QETH_LINK_TYPE_FAST_ETH:
+		case QETH_LINK_TYPE_LANE_ETH100:
+			link_info->speed = SPEED_100;
+			link_info->port = PORT_TP;
+			break;
+		case QETH_LINK_TYPE_GBIT_ETH:
+		case QETH_LINK_TYPE_LANE_ETH1000:
+			link_info->speed = SPEED_1000;
+			link_info->port = PORT_FIBRE;
+			break;
+		case QETH_LINK_TYPE_10GBIT_ETH:
+			link_info->speed = SPEED_10000;
+			link_info->port = PORT_FIBRE;
+			break;
+		case QETH_LINK_TYPE_25GBIT_ETH:
+			link_info->speed = SPEED_25000;
+			link_info->port = PORT_FIBRE;
+			break;
+		default:
+			dev_info(&card->gdev->dev,
+				 "Unknown link type %x\n",
+				 card->info.link_type);
+			link_info->speed = SPEED_UNKNOWN;
+			link_info->port = PORT_OTHER;
+		}
+
+		link_info->link_mode = QETH_LINK_MODE_UNKNOWN;
+	}
+}
+
 static struct qeth_ipa_cmd *qeth_check_ipa_data(struct qeth_card *card,
 						struct qeth_ipa_cmd *cmd)
 {
@@ -797,6 +838,7 @@
 				 netdev_name(card->dev), card->info.chpid);
 			qeth_issue_ipa_msg(cmd, cmd->hdr.return_code, card);
 			netif_carrier_off(card->dev);
+			qeth_default_link_info(card);
 		}
 		return NULL;
 	case IPA_CMD_STARTLAN:
@@ -1142,6 +1184,20 @@
 	}
 }
 
+/**
+ * qeth_irq() - qeth interrupt handler
+ * @cdev: ccw device
+ * @intparm: expect pointer to iob
+ * @irb: Interruption Response Block
+ *
+ * In the good path:
+ * corresponding qeth channel is locked with last used iob as active_cmd.
+ * But this function is also called for error interrupts.
+ *
+ * Caller ensures that:
+ * Interrupts are disabled; ccw device lock is held;
+ *
+ */
 static void qeth_irq(struct ccw_device *cdev, unsigned long intparm,
 		struct irb *irb)
 {
@@ -1183,11 +1239,10 @@
 		iob = (struct qeth_cmd_buffer *) (addr_t)intparm;
 	}
 
-	qeth_unlock_channel(card, channel);
-
 	rc = qeth_check_irb_error(card, cdev, irb);
 	if (rc) {
 		/* IO was terminated, free its resources. */
+		qeth_unlock_channel(card, channel);
 		if (iob)
 			qeth_cancel_cmd(iob, rc);
 		return;
@@ -1231,6 +1286,7 @@
 		rc = qeth_get_problem(card, cdev, irb);
 		if (rc) {
 			card->read_or_write_problem = 1;
+			qeth_unlock_channel(card, channel);
 			if (iob)
 				qeth_cancel_cmd(iob, rc);
 			qeth_clear_ipacmd_list(card);
@@ -1239,6 +1295,26 @@
 		}
 	}
 
+	if (scsw_cmd_is_valid_cc(&irb->scsw) && irb->scsw.cmd.cc == 1 && iob) {
+		/* channel command hasn't started: retry.
+		 * active_cmd is still set to last iob
+		 */
+		QETH_CARD_TEXT(card, 2, "irqcc1");
+		rc = ccw_device_start_timeout(cdev, __ccw_from_cmd(iob),
+					      (addr_t)iob, 0, 0, iob->timeout);
+		if (rc) {
+			QETH_DBF_MESSAGE(2,
+					 "ccw retry on %x failed, rc = %i\n",
+					 CARD_DEVID(card), rc);
+			QETH_CARD_TEXT_(card, 2, " err%d", rc);
+			qeth_unlock_channel(card, channel);
+			qeth_cancel_cmd(iob, rc);
+		}
+		return;
+	}
+
+	qeth_unlock_channel(card, channel);
+
 	if (iob) {
 		/* sanity check: */
 		if (irb->scsw.cmd.count > iob->length) {
@@ -1458,7 +1534,6 @@
 	card->qdio.default_out_queue = QETH_DEFAULT_QUEUE;
 
 	/* inbound */
-	card->qdio.no_in_queues = 1;
 	card->qdio.in_buf_size = QETH_IN_BUF_SIZE_DEFAULT;
 	if (IS_IQD(card))
 		card->qdio.init_pool.buf_count = QETH_IN_BUF_COUNT_HSDEFAULT;
@@ -2558,6 +2633,10 @@
 
 	QETH_CARD_TEXT(card, 2, "allcqdbf");
 
+	/* completion */
+	if (qeth_alloc_cq(card))
+		goto out_err;
+
 	if (atomic_cmpxchg(&card->qdio.state, QETH_QDIO_UNINITIALIZED,
 		QETH_QDIO_ALLOCATED) != QETH_QDIO_UNINITIALIZED)
 		return 0;
@@ -2598,10 +2677,6 @@
 		queue->priority = QETH_QIB_PQUE_PRIO_DEFAULT;
 	}
 
-	/* completion */
-	if (qeth_alloc_cq(card))
-		goto out_freeoutq;
-
 	return 0;
 
 out_freeoutq:
@@ -2615,6 +2690,8 @@
 	card->qdio.in_q = NULL;
 out_nomem:
 	atomic_set(&card->qdio.state, QETH_QDIO_UNINITIALIZED);
+	qeth_free_cq(card);
+out_err:
 	return -ENOMEM;
 }
 
@@ -2622,11 +2699,12 @@
 {
 	int i, j;
 
+	qeth_free_cq(card);
+
 	if (atomic_xchg(&card->qdio.state, QETH_QDIO_UNINITIALIZED) ==
 		QETH_QDIO_UNINITIALIZED)
 		return;
 
-	qeth_free_cq(card);
 	for (j = 0; j < QDIO_MAX_BUFFERS_PER_Q; ++j) {
 		if (card->qdio.in_q->bufs[j].rx_skb)
 			dev_kfree_skb_any(card->qdio.in_q->bufs[j].rx_skb);
@@ -3679,24 +3757,11 @@
 
 int qeth_configure_cq(struct qeth_card *card, enum qeth_cq cq)
 {
-	int rc;
-
-	if (card->options.cq ==  QETH_CQ_NOTAVAILABLE) {
-		rc = -1;
-		goto out;
-	} else {
-		if (card->options.cq == cq) {
-			rc = 0;
-			goto out;
-		}
-
-		qeth_free_qdio_queues(card);
-		card->options.cq = cq;
-		rc = 0;
-	}
-out:
-	return rc;
+	if (card->options.cq == QETH_CQ_NOTAVAILABLE)
+		return -1;
 
+	card->options.cq = cq;
+	return 0;
 }
 EXPORT_SYMBOL_GPL(qeth_configure_cq);
 
@@ -4760,92 +4825,6 @@
 	return rc;
 }
 
-static int qeth_query_card_info_cb(struct qeth_card *card,
-				   struct qeth_reply *reply, unsigned long data)
-{
-	struct qeth_ipa_cmd *cmd = (struct qeth_ipa_cmd *)data;
-	struct qeth_link_info *link_info = reply->param;
-	struct qeth_query_card_info *card_info;
-
-	QETH_CARD_TEXT(card, 2, "qcrdincb");
-	if (qeth_setadpparms_inspect_rc(cmd))
-		return -EIO;
-
-	card_info = &cmd->data.setadapterparms.data.card_info;
-	netdev_dbg(card->dev,
-		   "card info: card_type=0x%02x, port_mode=0x%04x, port_speed=0x%08x\n",
-		   card_info->card_type, card_info->port_mode,
-		   card_info->port_speed);
-
-	switch (card_info->port_mode) {
-	case CARD_INFO_PORTM_FULLDUPLEX:
-		link_info->duplex = DUPLEX_FULL;
-		break;
-	case CARD_INFO_PORTM_HALFDUPLEX:
-		link_info->duplex = DUPLEX_HALF;
-		break;
-	default:
-		link_info->duplex = DUPLEX_UNKNOWN;
-	}
-
-	switch (card_info->card_type) {
-	case CARD_INFO_TYPE_1G_COPPER_A:
-	case CARD_INFO_TYPE_1G_COPPER_B:
-		link_info->speed = SPEED_1000;
-		link_info->port = PORT_TP;
-		break;
-	case CARD_INFO_TYPE_1G_FIBRE_A:
-	case CARD_INFO_TYPE_1G_FIBRE_B:
-		link_info->speed = SPEED_1000;
-		link_info->port = PORT_FIBRE;
-		break;
-	case CARD_INFO_TYPE_10G_FIBRE_A:
-	case CARD_INFO_TYPE_10G_FIBRE_B:
-		link_info->speed = SPEED_10000;
-		link_info->port = PORT_FIBRE;
-		break;
-	default:
-		switch (card_info->port_speed) {
-		case CARD_INFO_PORTS_10M:
-			link_info->speed = SPEED_10;
-			break;
-		case CARD_INFO_PORTS_100M:
-			link_info->speed = SPEED_100;
-			break;
-		case CARD_INFO_PORTS_1G:
-			link_info->speed = SPEED_1000;
-			break;
-		case CARD_INFO_PORTS_10G:
-			link_info->speed = SPEED_10000;
-			break;
-		case CARD_INFO_PORTS_25G:
-			link_info->speed = SPEED_25000;
-			break;
-		default:
-			link_info->speed = SPEED_UNKNOWN;
-		}
-
-		link_info->port = PORT_OTHER;
-	}
-
-	return 0;
-}
-
-int qeth_query_card_info(struct qeth_card *card,
-			 struct qeth_link_info *link_info)
-{
-	struct qeth_cmd_buffer *iob;
-
-	QETH_CARD_TEXT(card, 2, "qcrdinfo");
-	if (!qeth_adp_supported(card, IPA_SETADP_QUERY_CARD_INFO))
-		return -EOPNOTSUPP;
-	iob = qeth_get_adapter_cmd(card, IPA_SETADP_QUERY_CARD_INFO, 0);
-	if (!iob)
-		return -ENOMEM;
-
-	return qeth_send_ipa_cmd(card, iob, qeth_query_card_info_cb, link_info);
-}
-
 static int qeth_init_link_info_oat_cb(struct qeth_card *card,
 				      struct qeth_reply *reply_priv,
 				      unsigned long data)
@@ -4855,6 +4834,7 @@
 	struct qeth_query_oat_physical_if *phys_if;
 	struct qeth_query_oat_reply *reply;
 
+	QETH_CARD_TEXT(card, 2, "qoatincb");
 	if (qeth_setadpparms_inspect_rc(cmd))
 		return -EIO;
 
@@ -4934,41 +4914,7 @@
 
 static void qeth_init_link_info(struct qeth_card *card)
 {
-	card->info.link_info.duplex = DUPLEX_FULL;
-
-	if (IS_IQD(card) || IS_VM_NIC(card)) {
-		card->info.link_info.speed = SPEED_10000;
-		card->info.link_info.port = PORT_FIBRE;
-		card->info.link_info.link_mode = QETH_LINK_MODE_FIBRE_SHORT;
-	} else {
-		switch (card->info.link_type) {
-		case QETH_LINK_TYPE_FAST_ETH:
-		case QETH_LINK_TYPE_LANE_ETH100:
-			card->info.link_info.speed = SPEED_100;
-			card->info.link_info.port = PORT_TP;
-			break;
-		case QETH_LINK_TYPE_GBIT_ETH:
-		case QETH_LINK_TYPE_LANE_ETH1000:
-			card->info.link_info.speed = SPEED_1000;
-			card->info.link_info.port = PORT_FIBRE;
-			break;
-		case QETH_LINK_TYPE_10GBIT_ETH:
-			card->info.link_info.speed = SPEED_10000;
-			card->info.link_info.port = PORT_FIBRE;
-			break;
-		case QETH_LINK_TYPE_25GBIT_ETH:
-			card->info.link_info.speed = SPEED_25000;
-			card->info.link_info.port = PORT_FIBRE;
-			break;
-		default:
-			dev_info(&card->gdev->dev, "Unknown link type %x\n",
-				 card->info.link_type);
-			card->info.link_info.speed = SPEED_UNKNOWN;
-			card->info.link_info.port = PORT_OTHER;
-		}
-
-		card->info.link_info.link_mode = QETH_LINK_MODE_UNKNOWN;
-	}
+	qeth_default_link_info(card);
 
 	/* Get more accurate data via QUERY OAT: */
 	if (qeth_adp_supported(card, IPA_SETADP_QUERY_OAT)) {
@@ -5139,6 +5085,7 @@
 	struct qdio_buffer **in_sbal_ptrs[QETH_MAX_IN_QUEUES];
 	struct qeth_qib_parms *qib_parms = NULL;
 	struct qdio_initialize init_data;
+	unsigned int no_input_qs = 1;
 	unsigned int i;
 	int rc = 0;
 
@@ -5153,8 +5100,10 @@
 	}
 
 	in_sbal_ptrs[0] = card->qdio.in_q->qdio_bufs;
-	if (card->options.cq == QETH_CQ_ENABLED)
+	if (card->options.cq == QETH_CQ_ENABLED) {
 		in_sbal_ptrs[1] = card->qdio.c_q->qdio_bufs;
+		no_input_qs++;
+	}
 
 	for (i = 0; i < card->qdio.no_out_queues; i++)
 		out_sbal_ptrs[i] = card->qdio.out_qs[i]->qdio_bufs;
@@ -5164,7 +5113,7 @@
 							  QDIO_QETH_QFMT;
 	init_data.qib_param_field_format = 0;
 	init_data.qib_param_field	 = (void *)qib_parms;
-	init_data.no_input_qs            = card->qdio.no_in_queues;
+	init_data.no_input_qs		 = no_input_qs;
 	init_data.no_output_qs           = card->qdio.no_out_queues;
 	init_data.input_handler		 = qeth_qdio_input_handler;
 	init_data.output_handler	 = qeth_qdio_output_handler;
@@ -5459,8 +5408,6 @@
 	qeth_clear_ipacmd_list(card);
 
 	rtnl_lock();
-	card->info.open_when_online = card->dev->flags & IFF_UP;
-	dev_close(card->dev);
 	netif_device_detach(card->dev);
 	netif_carrier_off(card->dev);
 	rtnl_unlock();
@@ -5474,6 +5421,7 @@
 	qeth_clear_working_pool_list(card);
 	qeth_flush_local_addrs(card);
 	card->info.promisc_mode = 0;
+	qeth_default_link_info(card);
 
 	rc  = qeth_stop_channel(&card->data);
 	rc2 = qeth_stop_channel(&card->write);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/qeth_ethtool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/qeth_ethtool.c
@@ -426,8 +426,8 @@
 				   struct ethtool_link_ksettings *cmd)
 {
 	struct qeth_card *card = netdev->ml_priv;
-	struct qeth_link_info link_info;
 
+	QETH_CARD_TEXT(card, 4, "ethtglks");
 	cmd->base.speed = card->info.link_info.speed;
 	cmd->base.duplex = card->info.link_info.duplex;
 	cmd->base.port = card->info.link_info.port;
@@ -437,16 +437,6 @@
 	cmd->base.eth_tp_mdix = ETH_TP_MDI_INVALID;
 	cmd->base.eth_tp_mdix_ctrl = ETH_TP_MDI_INVALID;
 
-	/* Check if we can obtain more accurate information.	 */
-	if (!qeth_query_card_info(card, &link_info)) {
-		if (link_info.speed != SPEED_UNKNOWN)
-			cmd->base.speed = link_info.speed;
-		if (link_info.duplex != DUPLEX_UNKNOWN)
-			cmd->base.duplex = link_info.duplex;
-		if (link_info.port != PORT_OTHER)
-			cmd->base.port = link_info.port;
-	}
-
 	qeth_set_ethtool_link_modes(cmd, card->info.link_info.link_mode);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/qeth_l2_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/qeth_l2_main.c
@@ -661,13 +661,13 @@
 					 card->dev, &info.info, NULL);
 		QETH_CARD_TEXT(card, 4, "andelmac");
 		QETH_CARD_TEXT_(card, 4,
-				"mc%012lx", ether_addr_to_u64(ntfy_mac));
+				"mc%012llx", ether_addr_to_u64(ntfy_mac));
 	} else {
 		call_switchdev_notifiers(SWITCHDEV_FDB_ADD_TO_BRIDGE,
 					 card->dev, &info.info, NULL);
 		QETH_CARD_TEXT(card, 4, "anaddmac");
 		QETH_CARD_TEXT_(card, 4,
-				"mc%012lx", ether_addr_to_u64(ntfy_mac));
+				"mc%012llx", ether_addr_to_u64(ntfy_mac));
 	}
 }
 
@@ -764,9 +764,8 @@
 	struct list_head *iter;
 	int err = 0;
 
-	kfree(br2dev_event_work);
-	QETH_CARD_TEXT_(card, 4, "b2dw%04x", event);
-	QETH_CARD_TEXT_(card, 4, "ma%012lx", ether_addr_to_u64(addr));
+	QETH_CARD_TEXT_(card, 4, "b2dw%04lx", event);
+	QETH_CARD_TEXT_(card, 4, "ma%012llx", ether_addr_to_u64(addr));
 
 	rcu_read_lock();
 	/* Verify preconditions are still valid: */
@@ -795,7 +794,7 @@
 				if (err) {
 					QETH_CARD_TEXT(card, 2, "b2derris");
 					QETH_CARD_TEXT_(card, 2,
-							"err%02x%03d", event,
+							"err%02lx%03d", event,
 							lowerdev->ifindex);
 				}
 			}
@@ -813,7 +812,7 @@
 			break;
 		}
 		if (err)
-			QETH_CARD_TEXT_(card, 2, "b2derr%02x", event);
+			QETH_CARD_TEXT_(card, 2, "b2derr%02lx", event);
 	}
 
 unlock:
@@ -821,6 +820,7 @@
 	dev_put(brdev);
 	dev_put(lsyncdev);
 	dev_put(dstdev);
+	kfree(br2dev_event_work);
 }
 
 static int qeth_l2_br2dev_queue_work(struct net_device *brdev,
@@ -878,7 +878,7 @@
 	while (lowerdev) {
 		if (qeth_l2_must_learn(lowerdev, dstdev)) {
 			card = lowerdev->ml_priv;
-			QETH_CARD_TEXT_(card, 4, "b2dqw%03x", event);
+			QETH_CARD_TEXT_(card, 4, "b2dqw%03lx", event);
 			rc = qeth_l2_br2dev_queue_work(brdev, lowerdev,
 						       dstdev, event,
 						       fdb_info->addr);
@@ -2373,9 +2373,12 @@
 		qeth_enable_hw_features(dev);
 		qeth_l2_enable_brport_features(card);
 
-		if (card->info.open_when_online) {
-			card->info.open_when_online = 0;
-			dev_open(dev, NULL);
+		if (netif_running(dev)) {
+			local_bh_disable();
+			napi_schedule(&card->napi);
+			/* kick-start the NAPI softirq: */
+			local_bh_enable();
+			qeth_l2_set_rx_mode(dev);
 		}
 		rtnl_unlock();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/qeth_l3_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/qeth_l3_main.c
@@ -254,9 +254,10 @@
 		if (!recover) {
 			hash_del(&addr->hnode);
 			kfree(addr);
-			continue;
+		} else {
+			/* prepare for recovery */
+			addr->disp_flag = QETH_DISP_ADDR_ADD;
 		}
-		addr->disp_flag = QETH_DISP_ADDR_ADD;
 	}
 
 	mutex_unlock(&card->ip_lock);
@@ -277,9 +278,11 @@
 		if (addr->disp_flag == QETH_DISP_ADDR_ADD) {
 			rc = qeth_l3_register_addr_entry(card, addr);
 
-			if (!rc) {
+			if (!rc || rc == -EADDRINUSE || rc == -ENETDOWN) {
+				/* keep it in the records */
 				addr->disp_flag = QETH_DISP_ADDR_DO_NOTHING;
 			} else {
+				/* bad address */
 				hash_del(&addr->hnode);
 				kfree(addr);
 			}
@@ -2029,9 +2032,11 @@
 		netif_device_attach(dev);
 		qeth_enable_hw_features(dev);
 
-		if (card->info.open_when_online) {
-			card->info.open_when_online = 0;
-			dev_open(dev, NULL);
+		if (netif_running(dev)) {
+			local_bh_disable();
+			napi_schedule(&card->napi);
+			/* kick-start the NAPI softirq: */
+			local_bh_enable();
 		}
 		rtnl_unlock();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/net/qeth_l3_sys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/net/qeth_l3_sys.c
@@ -652,7 +652,7 @@
 static ssize_t qeth_l3_dev_vipa_del4_store(struct device *dev,
 		struct device_attribute *attr, const char *buf, size_t count)
 {
-	return qeth_l3_vipa_store(dev, buf, true, count, QETH_PROT_IPV4);
+	return qeth_l3_vipa_store(dev, buf, false, count, QETH_PROT_IPV4);
 }
 
 static QETH_DEVICE_ATTR(vipa_del4, del4, 0200, NULL,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/scsi/zfcp_aux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/scsi/zfcp_aux.c
@@ -518,12 +518,12 @@
 	if (port) {
 		put_device(&port->dev);
 		retval = -EEXIST;
-		goto err_out;
+		goto err_put;
 	}
 
 	port = kzalloc(sizeof(struct zfcp_port), GFP_KERNEL);
 	if (!port)
-		goto err_out;
+		goto err_put;
 
 	rwlock_init(&port->unit_list_lock);
 	INIT_LIST_HEAD(&port->unit_list);
@@ -546,7 +546,7 @@
 
 	if (dev_set_name(&port->dev, "0x%016llx", (unsigned long long)wwpn)) {
 		kfree(port);
-		goto err_out;
+		goto err_put;
 	}
 	retval = -EINVAL;
 
@@ -563,7 +563,8 @@
 
 	return port;
 
-err_out:
+err_put:
 	zfcp_ccw_adapter_put(adapter);
+err_out:
 	return ERR_PTR(retval);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/scsi/zfcp_fc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/scsi/zfcp_fc.c
@@ -145,27 +145,33 @@
 
 static int zfcp_fc_wka_port_get(struct zfcp_fc_wka_port *wka_port)
 {
+	int ret = -EIO;
+
 	if (mutex_lock_interruptible(&wka_port->mutex))
 		return -ERESTARTSYS;
 
 	if (wka_port->status == ZFCP_FC_WKA_PORT_OFFLINE ||
 	    wka_port->status == ZFCP_FC_WKA_PORT_CLOSING) {
 		wka_port->status = ZFCP_FC_WKA_PORT_OPENING;
-		if (zfcp_fsf_open_wka_port(wka_port))
+		if (zfcp_fsf_open_wka_port(wka_port)) {
+			/* could not even send request, nothing to wait for */
 			wka_port->status = ZFCP_FC_WKA_PORT_OFFLINE;
+			goto out;
+		}
 	}
 
-	mutex_unlock(&wka_port->mutex);
-
-	wait_event(wka_port->completion_wq,
+	wait_event(wka_port->opened,
 		   wka_port->status == ZFCP_FC_WKA_PORT_ONLINE ||
 		   wka_port->status == ZFCP_FC_WKA_PORT_OFFLINE);
 
 	if (wka_port->status == ZFCP_FC_WKA_PORT_ONLINE) {
 		atomic_inc(&wka_port->refcount);
-		return 0;
+		ret = 0;
+		goto out;
 	}
-	return -EIO;
+out:
+	mutex_unlock(&wka_port->mutex);
+	return ret;
 }
 
 static void zfcp_fc_wka_port_offline(struct work_struct *work)
@@ -181,9 +187,12 @@
 
 	wka_port->status = ZFCP_FC_WKA_PORT_CLOSING;
 	if (zfcp_fsf_close_wka_port(wka_port)) {
+		/* could not even send request, nothing to wait for */
 		wka_port->status = ZFCP_FC_WKA_PORT_OFFLINE;
-		wake_up(&wka_port->completion_wq);
+		goto out;
 	}
+	wait_event(wka_port->closed,
+		   wka_port->status == ZFCP_FC_WKA_PORT_OFFLINE);
 out:
 	mutex_unlock(&wka_port->mutex);
 }
@@ -193,13 +202,15 @@
 	if (atomic_dec_return(&wka_port->refcount) != 0)
 		return;
 	/* wait 10 milliseconds, other reqs might pop in */
-	schedule_delayed_work(&wka_port->work, HZ / 100);
+	queue_delayed_work(wka_port->adapter->work_queue, &wka_port->work,
+			   msecs_to_jiffies(10));
 }
 
 static void zfcp_fc_wka_port_init(struct zfcp_fc_wka_port *wka_port, u32 d_id,
 				  struct zfcp_adapter *adapter)
 {
-	init_waitqueue_head(&wka_port->completion_wq);
+	init_waitqueue_head(&wka_port->opened);
+	init_waitqueue_head(&wka_port->closed);
 
 	wka_port->adapter = adapter;
 	wka_port->d_id = d_id;
@@ -521,8 +532,9 @@
 		goto out;
 	}
 
-	/* port is good, unblock rport without going through erp */
-	zfcp_scsi_schedule_rport_register(port);
+	/* re-init to undo drop from zfcp_fc_adisc() */
+	port->d_id = ntoh24(adisc_resp->adisc_port_id);
+	/* port is still good, nothing to do */
  out:
 	atomic_andnot(ZFCP_STATUS_PORT_LINK_TEST, &port->status);
 	put_device(&port->dev);
@@ -534,6 +546,7 @@
 	struct zfcp_fc_req *fc_req;
 	struct zfcp_adapter *adapter = port->adapter;
 	struct Scsi_Host *shost = adapter->scsi_host;
+	u32 d_id;
 	int ret;
 
 	fc_req = kmem_cache_zalloc(zfcp_fc_req_cache, GFP_ATOMIC);
@@ -558,7 +571,15 @@
 	fc_req->u.adisc.req.adisc_cmd = ELS_ADISC;
 	hton24(fc_req->u.adisc.req.adisc_port_id, fc_host_port_id(shost));
 
-	ret = zfcp_fsf_send_els(adapter, port->d_id, &fc_req->ct_els,
+	d_id = port->d_id; /* remember as destination for send els below */
+	/*
+	 * Force fresh GID_PN lookup on next port recovery.
+	 * Must happen after request setup and before sending request,
+	 * to prevent race with port->d_id re-init in zfcp_fc_adisc_handler().
+	 */
+	port->d_id = 0;
+
+	ret = zfcp_fsf_send_els(adapter, d_id, &fc_req->ct_els,
 				ZFCP_FC_CTELS_TMO);
 	if (ret)
 		kmem_cache_free(zfcp_fc_req_cache, fc_req);
@@ -573,9 +594,6 @@
 	int retval;
 
 	set_worker_desc("zadisc%16llx", port->wwpn); /* < WORKER_DESC_LEN=24 */
-	get_device(&port->dev);
-	port->rport_task = RPORT_DEL;
-	zfcp_scsi_rport_work(&port->rport_work);
 
 	/* only issue one test command at one time per port */
 	if (atomic_read(&port->status) & ZFCP_STATUS_PORT_LINK_TEST)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/scsi/zfcp_fc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/scsi/zfcp_fc.h
@@ -185,7 +185,8 @@
 /**
  * struct zfcp_fc_wka_port - representation of well-known-address (WKA) FC port
  * @adapter: Pointer to adapter structure this WKA port belongs to
- * @completion_wq: Wait for completion of open/close command
+ * @opened: Wait for completion of open command
+ * @closed: Wait for completion of close command
  * @status: Current status of WKA port
  * @refcount: Reference count to keep port open as long as it is in use
  * @d_id: FC destination id or well-known-address
@@ -195,7 +196,8 @@
  */
 struct zfcp_fc_wka_port {
 	struct zfcp_adapter	*adapter;
-	wait_queue_head_t	completion_wq;
+	wait_queue_head_t	opened;
+	wait_queue_head_t	closed;
 	enum zfcp_fc_wka_status	status;
 	atomic_t		refcount;
 	u32			d_id;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/scsi/zfcp_fsf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/scsi/zfcp_fsf.c
@@ -884,7 +884,7 @@
 	const bool is_srb = zfcp_fsf_req_is_status_read_buffer(req);
 	struct zfcp_adapter *adapter = req->adapter;
 	struct zfcp_qdio *qdio = adapter->qdio;
-	int req_id = req->req_id;
+	unsigned long req_id = req->req_id;
 
 	zfcp_reqlist_add(adapter->req_list, req);
 
@@ -1907,7 +1907,7 @@
 		wka_port->status = ZFCP_FC_WKA_PORT_ONLINE;
 	}
 out:
-	wake_up(&wka_port->completion_wq);
+	wake_up(&wka_port->opened);
 }
 
 /**
@@ -1966,7 +1966,7 @@
 	}
 
 	wka_port->status = ZFCP_FC_WKA_PORT_OFFLINE;
-	wake_up(&wka_port->completion_wq);
+	wake_up(&wka_port->closed);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/s390/virtio/virtio_ccw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/s390/virtio/virtio_ccw.c
@@ -33,6 +33,7 @@
 #include <asm/virtio-ccw.h>
 #include <asm/isc.h>
 #include <asm/airq.h>
+#include <asm/tpi.h>
 
 /*
  * virtio related functions
@@ -203,7 +204,8 @@
 	write_unlock_irqrestore(&info->lock, flags);
 }
 
-static void virtio_airq_handler(struct airq_struct *airq, bool floating)
+static void virtio_airq_handler(struct airq_struct *airq,
+				struct tpi_info *tpi_info)
 {
 	struct airq_info *info = container_of(airq, struct airq_info, airq);
 	unsigned long ai;
@@ -239,7 +241,7 @@
 		return NULL;
 	rwlock_init(&info->lock);
 	info->aiv = airq_iv_create(VIRTIO_IV_BITS, AIRQ_IV_ALLOC | AIRQ_IV_PTR
-				   | AIRQ_IV_CACHELINE);
+				   | AIRQ_IV_CACHELINE, NULL);
 	if (!info->aiv) {
 		kfree(info);
 		return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/3w-9xxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/3w-9xxx.c
@@ -2006,7 +2006,7 @@
 	retval = pci_enable_device(pdev);
 	if (retval) {
 		TW_PRINTK(host, TW_DRIVER, 0x34, "Failed to enable pci device");
-		goto out_disable_device;
+		return -ENODEV;
 	}
 
 	pci_set_master(pdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/3w-xxxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/3w-xxxx.c
@@ -2305,8 +2305,10 @@
 	TW_DISABLE_INTERRUPTS(tw_dev);
 
 	/* Initialize the card */
-	if (tw_reset_sequence(tw_dev))
+	if (tw_reset_sequence(tw_dev)) {
+		retval = -EINVAL;
 		goto out_release_mem_region;
+	}
 
 	/* Set host specific parameters */
 	host->max_id = TW_MAX_UNITS;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/53c700.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/53c700.c
@@ -1599,7 +1599,7 @@
 				printk("scsi%d (%d:%d) PHASE MISMATCH IN SEND MESSAGE %d remain, return %p[%04x], phase %s\n", host->host_no, pun, lun, count, (void *)temp, temp - hostdata->pScript, sbcl_to_string(NCR_700_readb(host, SBCL_REG)));
 #endif
 				resume_offset = hostdata->pScript + Ent_SendMessagePhaseMismatch;
-			} else if(dsp >= to32bit(&slot->pSG[0].ins) &&
+			} else if (slot && dsp >= to32bit(&slot->pSG[0].ins) &&
 				  dsp <= to32bit(&slot->pSG[NCR_700_SG_SEGMENTS].ins)) {
 				int data_transfer = NCR_700_readl(host, DBC_REG) & 0xffffff;
 				int SGcount = (dsp - to32bit(&slot->pSG[0].ins))/sizeof(struct NCR_700_SG_List);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/Kconfig
@@ -460,7 +460,7 @@
 
 config SCSI_DPT_I2O
 	tristate "Adaptec I2O RAID support "
-	depends on SCSI && PCI && VIRT_TO_BUS
+	depends on SCSI && PCI
 	help
 	  This driver supports all of Adaptec's I2O based RAID controllers as 
 	  well as the DPT SmartRaid V cards.  This is an Adaptec maintained
@@ -1296,7 +1296,7 @@
 
 config JAZZ_ESP
 	bool "MIPS JAZZ FAS216 SCSI support"
-	depends on MACH_JAZZ && SCSI
+	depends on MACH_JAZZ && SCSI=y
 	select SCSI_SPI_ATTRS
 	help
 	  This is the driver for the onboard SCSI host adapter of MIPS Magnum
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/NCR5380.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/NCR5380.c
@@ -84,8 +84,7 @@
  * On command termination, the done function will be called as
  * appropriate.
  *
- * SCSI pointers are maintained in the SCp field of SCSI command
- * structures, being initialized after the command is connected
+ * The command data pointer is initialized after the command is connected
  * in NCR5380_select, and set as appropriate in NCR5380_information_transfer.
  * Note that in violation of the standard, an implicit SAVE POINTERS operation
  * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS.
@@ -145,40 +144,38 @@
 
 static inline void initialize_SCp(struct scsi_cmnd *cmd)
 {
-	/*
-	 * Initialize the Scsi Pointer field so that all of the commands in the
-	 * various queues are valid.
-	 */
+	struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd);
 
 	if (scsi_bufflen(cmd)) {
-		cmd->SCp.buffer = scsi_sglist(cmd);
-		cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
-		cmd->SCp.this_residual = cmd->SCp.buffer->length;
+		ncmd->buffer = scsi_sglist(cmd);
+		ncmd->ptr = sg_virt(ncmd->buffer);
+		ncmd->this_residual = ncmd->buffer->length;
 	} else {
-		cmd->SCp.buffer = NULL;
-		cmd->SCp.ptr = NULL;
-		cmd->SCp.this_residual = 0;
+		ncmd->buffer = NULL;
+		ncmd->ptr = NULL;
+		ncmd->this_residual = 0;
 	}
 
-	cmd->SCp.Status = 0;
-	cmd->SCp.Message = 0;
+	ncmd->status = 0;
+	ncmd->message = 0;
 }
 
-static inline void advance_sg_buffer(struct scsi_cmnd *cmd)
+static inline void advance_sg_buffer(struct NCR5380_cmd *ncmd)
 {
-	struct scatterlist *s = cmd->SCp.buffer;
+	struct scatterlist *s = ncmd->buffer;
 
-	if (!cmd->SCp.this_residual && s && !sg_is_last(s)) {
-		cmd->SCp.buffer = sg_next(s);
-		cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
-		cmd->SCp.this_residual = cmd->SCp.buffer->length;
+	if (!ncmd->this_residual && s && !sg_is_last(s)) {
+		ncmd->buffer = sg_next(s);
+		ncmd->ptr = sg_virt(ncmd->buffer);
+		ncmd->this_residual = ncmd->buffer->length;
 	}
 }
 
 static inline void set_resid_from_SCp(struct scsi_cmnd *cmd)
 {
-	int resid = cmd->SCp.this_residual;
-	struct scatterlist *s = cmd->SCp.buffer;
+	struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd);
+	int resid = ncmd->this_residual;
+	struct scatterlist *s = ncmd->buffer;
 
 	if (s)
 		while (!sg_is_last(s)) {
@@ -564,7 +561,7 @@
                                  struct scsi_cmnd *cmd)
 {
 	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
+	struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd);
 	unsigned long flags;
 
 #if (NDEBUG & NDEBUG_NO_WRITE)
@@ -672,7 +669,7 @@
 static void requeue_cmd(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
 {
 	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
+	struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd);
 
 	if (hostdata->sensing == cmd) {
 		scsi_eh_restore_cmnd(cmd, &hostdata->ses);
@@ -757,6 +754,7 @@
 static void NCR5380_dma_complete(struct Scsi_Host *instance)
 {
 	struct NCR5380_hostdata *hostdata = shost_priv(instance);
+	struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(hostdata->connected);
 	int transferred;
 	unsigned char **data;
 	int *count;
@@ -764,7 +762,7 @@
 	unsigned char p;
 
 	if (hostdata->read_overruns) {
-		p = hostdata->connected->SCp.phase;
+		p = ncmd->phase;
 		if (p & SR_IO) {
 			udelay(10);
 			if ((NCR5380_read(BUS_AND_STATUS_REG) &
@@ -801,8 +799,8 @@
 	transferred = hostdata->dma_len - NCR5380_dma_residual(hostdata);
 	hostdata->dma_len = 0;
 
-	data = (unsigned char **)&hostdata->connected->SCp.ptr;
-	count = &hostdata->connected->SCp.this_residual;
+	data = (unsigned char **)&ncmd->ptr;
+	count = &ncmd->this_residual;
 	*data += transferred;
 	*count -= transferred;
 
@@ -1487,6 +1485,7 @@
 				unsigned char **data)
 {
 	struct NCR5380_hostdata *hostdata = shost_priv(instance);
+	struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(hostdata->connected);
 	int c = *count;
 	unsigned char p = *phase;
 	unsigned char *d = *data;
@@ -1498,7 +1497,7 @@
 		return -1;
 	}
 
-	hostdata->connected->SCp.phase = p;
+	ncmd->phase = p;
 
 	if (p & SR_IO) {
 		if (hostdata->read_overruns)
@@ -1610,45 +1609,44 @@
  * request.
  */
 
-	if (hostdata->flags & FLAG_DMA_FIXUP) {
-		if (p & SR_IO) {
-			/*
-			 * The workaround was to transfer fewer bytes than we
-			 * intended to with the pseudo-DMA read function, wait for
-			 * the chip to latch the last byte, read it, and then disable
-			 * pseudo-DMA mode.
-			 *
-			 * After REQ is asserted, the NCR5380 asserts DRQ and ACK.
-			 * REQ is deasserted when ACK is asserted, and not reasserted
-			 * until ACK goes false.  Since the NCR5380 won't lower ACK
-			 * until DACK is asserted, which won't happen unless we twiddle
-			 * the DMA port or we take the NCR5380 out of DMA mode, we
-			 * can guarantee that we won't handshake another extra
-			 * byte.
-			 */
-
-			if (NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG,
-			                          BASR_DRQ, BASR_DRQ, 0) < 0) {
-				result = -1;
-				shost_printk(KERN_ERR, instance, "PDMA read: DRQ timeout\n");
-			}
-			if (NCR5380_poll_politely(hostdata, STATUS_REG,
-			                          SR_REQ, 0, 0) < 0) {
-				result = -1;
-				shost_printk(KERN_ERR, instance, "PDMA read: !REQ timeout\n");
-			}
-			d[*count - 1] = NCR5380_read(INPUT_DATA_REG);
-		} else {
-			/*
-			 * Wait for the last byte to be sent.  If REQ is being asserted for
-			 * the byte we're interested, we'll ACK it and it will go false.
-			 */
-			if (NCR5380_poll_politely2(hostdata,
-			     BUS_AND_STATUS_REG, BASR_DRQ, BASR_DRQ,
-			     BUS_AND_STATUS_REG, BASR_PHASE_MATCH, 0, 0) < 0) {
-				result = -1;
-				shost_printk(KERN_ERR, instance, "PDMA write: DRQ and phase timeout\n");
+	if ((hostdata->flags & FLAG_DMA_FIXUP) &&
+	    (NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH)) {
+		/*
+		 * The workaround was to transfer fewer bytes than we
+		 * intended to with the pseudo-DMA receive function, wait for
+		 * the chip to latch the last byte, read it, and then disable
+		 * DMA mode.
+		 *
+		 * After REQ is asserted, the NCR5380 asserts DRQ and ACK.
+		 * REQ is deasserted when ACK is asserted, and not reasserted
+		 * until ACK goes false. Since the NCR5380 won't lower ACK
+		 * until DACK is asserted, which won't happen unless we twiddle
+		 * the DMA port or we take the NCR5380 out of DMA mode, we
+		 * can guarantee that we won't handshake another extra
+		 * byte.
+		 *
+		 * If sending, wait for the last byte to be sent. If REQ is
+		 * being asserted for the byte we're interested, we'll ACK it
+		 * and it will go false.
+		 */
+		if (!NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG,
+					   BASR_DRQ, BASR_DRQ, 0)) {
+			if ((p & SR_IO) &&
+			    (NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH)) {
+				if (!NCR5380_poll_politely(hostdata, STATUS_REG,
+							   SR_REQ, 0, 0)) {
+					d[c] = NCR5380_read(INPUT_DATA_REG);
+					--ncmd->this_residual;
+				} else {
+					result = -1;
+					scmd_printk(KERN_ERR, hostdata->connected,
+						    "PDMA fixup: !REQ timeout\n");
+				}
 			}
+		} else if (NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH) {
+			result = -1;
+			scmd_printk(KERN_ERR, hostdata->connected,
+				    "PDMA fixup: DRQ timeout\n");
 		}
 	}
 
@@ -1690,7 +1688,7 @@
 #endif
 
 	while ((cmd = hostdata->connected)) {
-		struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
+		struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd);
 
 		tmp = NCR5380_read(STATUS_REG);
 		/* We only have a valid SCSI phase when REQ is asserted */
@@ -1705,17 +1703,17 @@
 			    sun3_dma_setup_done != cmd) {
 				int count;
 
-				advance_sg_buffer(cmd);
+				advance_sg_buffer(ncmd);
 
 				count = sun3scsi_dma_xfer_len(hostdata, cmd);
 
 				if (count > 0) {
 					if (cmd->sc_data_direction == DMA_TO_DEVICE)
 						sun3scsi_dma_send_setup(hostdata,
-						                        cmd->SCp.ptr, count);
+									ncmd->ptr, count);
 					else
 						sun3scsi_dma_recv_setup(hostdata,
-						                        cmd->SCp.ptr, count);
+									ncmd->ptr, count);
 					sun3_dma_setup_done = cmd;
 				}
 #ifdef SUN3_SCSI_VME
@@ -1755,11 +1753,11 @@
 				 * scatter-gather list, move onto the next one.
 				 */
 
-				advance_sg_buffer(cmd);
+				advance_sg_buffer(ncmd);
 				dsprintk(NDEBUG_INFORMATION, instance,
 					"this residual %d, sg ents %d\n",
-					cmd->SCp.this_residual,
-					sg_nents(cmd->SCp.buffer));
+					ncmd->this_residual,
+					sg_nents(ncmd->buffer));
 
 				/*
 				 * The preferred transfer method is going to be
@@ -1778,7 +1776,7 @@
 				if (transfersize > 0) {
 					len = transfersize;
 					if (NCR5380_transfer_dma(instance, &phase,
-					    &len, (unsigned char **)&cmd->SCp.ptr)) {
+					    &len, (unsigned char **)&ncmd->ptr)) {
 						/*
 						 * If the watchdog timer fires, all future
 						 * accesses to this device will use the
@@ -1794,13 +1792,13 @@
 					/* Transfer a small chunk so that the
 					 * irq mode lock is not held too long.
 					 */
-					transfersize = min(cmd->SCp.this_residual,
+					transfersize = min(ncmd->this_residual,
 							   NCR5380_PIO_CHUNK_SIZE);
 					len = transfersize;
 					NCR5380_transfer_pio(instance, &phase, &len,
-					                     (unsigned char **)&cmd->SCp.ptr,
+							     (unsigned char **)&ncmd->ptr,
 							     0);
-					cmd->SCp.this_residual -= transfersize - len;
+					ncmd->this_residual -= transfersize - len;
 				}
 #ifdef CONFIG_SUN3
 				if (sun3_dma_setup_done == cmd)
@@ -1811,7 +1809,7 @@
 				len = 1;
 				data = &tmp;
 				NCR5380_transfer_pio(instance, &phase, &len, &data, 0);
-				cmd->SCp.Message = tmp;
+				ncmd->message = tmp;
 
 				switch (tmp) {
 				case ABORT:
@@ -1828,15 +1826,15 @@
 					hostdata->connected = NULL;
 					hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
 
-					set_status_byte(cmd, cmd->SCp.Status);
+					set_status_byte(cmd, ncmd->status);
 
 					set_resid_from_SCp(cmd);
 
 					if (cmd->cmnd[0] == REQUEST_SENSE)
 						complete_cmd(instance, cmd);
 					else {
-						if (cmd->SCp.Status == SAM_STAT_CHECK_CONDITION ||
-						    cmd->SCp.Status == SAM_STAT_COMMAND_TERMINATED) {
+						if (ncmd->status == SAM_STAT_CHECK_CONDITION ||
+						    ncmd->status == SAM_STAT_COMMAND_TERMINATED) {
 							dsprintk(NDEBUG_QUEUES, instance, "autosense: adding cmd %p to tail of autosense queue\n",
 							         cmd);
 							list_add_tail(&ncmd->list,
@@ -2000,7 +1998,7 @@
 				len = 1;
 				data = &tmp;
 				NCR5380_transfer_pio(instance, &phase, &len, &data, 0);
-				cmd->SCp.Status = tmp;
+				ncmd->status = tmp;
 				break;
 			default:
 				shost_printk(KERN_ERR, instance, "unknown phase\n");
@@ -2153,17 +2151,17 @@
 	if (sun3_dma_setup_done != tmp) {
 		int count;
 
-		advance_sg_buffer(tmp);
+		advance_sg_buffer(ncmd);
 
 		count = sun3scsi_dma_xfer_len(hostdata, tmp);
 
 		if (count > 0) {
 			if (tmp->sc_data_direction == DMA_TO_DEVICE)
 				sun3scsi_dma_send_setup(hostdata,
-				                        tmp->SCp.ptr, count);
+							ncmd->ptr, count);
 			else
 				sun3scsi_dma_recv_setup(hostdata,
-				                        tmp->SCp.ptr, count);
+							ncmd->ptr, count);
 			sun3_dma_setup_done = tmp;
 		}
 	}
@@ -2206,7 +2204,7 @@
                          struct scsi_cmnd *needle)
 {
 	if (list_find_cmd(haystack, needle)) {
-		struct NCR5380_cmd *ncmd = scsi_cmd_priv(needle);
+		struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(needle);
 
 		list_del(&ncmd->list);
 		return true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/NCR5380.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/NCR5380.h
@@ -227,6 +227,12 @@
 };
 
 struct NCR5380_cmd {
+	char *ptr;
+	int this_residual;
+	struct scatterlist *buffer;
+	int status;
+	int message;
+	int phase;
 	struct list_head list;
 };
 
@@ -242,6 +248,11 @@
 	return ((struct scsi_cmnd *)ncmd_ptr) - 1;
 }
 
+static inline struct NCR5380_cmd *NCR5380_to_ncmd(struct scsi_cmnd *cmd)
+{
+	return scsi_cmd_priv(cmd);
+}
+
 #ifndef NDEBUG
 #define NDEBUG (0)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/aacraid/aacraid.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/aacraid/aacraid.h
@@ -2028,8 +2028,8 @@
 };
 
 struct aac_srb_unit {
-	struct aac_srb		srb;
 	struct aac_srb_reply	srb_reply;
+	struct aac_srb		srb;
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/aacraid/comminit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/aacraid/comminit.c
@@ -642,6 +642,7 @@
 
 	if (aac_comm_init(dev)<0){
 		kfree(dev->queues);
+		dev->queues = NULL;
 		return NULL;
 	}
 	/*
@@ -649,6 +650,7 @@
 	 */
 	if (aac_fib_setup(dev) < 0) {
 		kfree(dev->queues);
+		dev->queues = NULL;
 		return NULL;
 	}
 		
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/advansys.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/advansys.c
@@ -3308,8 +3308,8 @@
 		   shost->host_no);
 
 	seq_printf(m,
-		   " iop_base 0x%lx, cable_detect: %X, err_code %u\n",
-		   (unsigned long)v->iop_base,
+		   " iop_base 0x%p, cable_detect: %X, err_code %u\n",
+		   v->iop_base,
 		   AdvReadWordRegister(iop_base,IOPW_SCSI_CFG1) & CABLE_DETECT,
 		   v->err_code);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/aha152x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/aha152x.c
@@ -3370,13 +3370,11 @@
 	setup[setup_count].synchronous = ints[0] >= 6 ? ints[6] : 1;
 	setup[setup_count].delay       = ints[0] >= 7 ? ints[7] : DELAY_DEFAULT;
 	setup[setup_count].ext_trans   = ints[0] >= 8 ? ints[8] : 0;
-	if (ints[0] > 8) {                                                /*}*/
+	if (ints[0] > 8)
 		printk(KERN_NOTICE "aha152x: usage: aha152x=<IOBASE>[,<IRQ>[,<SCSI ID>"
 		       "[,<RECONNECT>[,<PARITY>[,<SYNCHRONOUS>[,<DELAY>[,<EXT_TRANS>]]]]]]]\n");
-	} else {
+	else
 		setup_count++;
-		return 0;
-	}
 
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/aic94xx/aic94xx_task.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/aic94xx/aic94xx_task.c
@@ -50,6 +50,9 @@
 		dma_addr_t dma = dma_map_single(&asd_ha->pcidev->dev, p,
 						task->total_xfer_len,
 						task->data_dir);
+		if (dma_mapping_error(&asd_ha->pcidev->dev, dma))
+			return -ENOMEM;
+
 		sg_arr[0].bus_addr = cpu_to_le64((u64)dma);
 		sg_arr[0].size = cpu_to_le32(task->total_xfer_len);
 		sg_arr[0].flags |= ASD_SG_EL_LIST_EOL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/arcmsr/arcmsr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/arcmsr/arcmsr.h
@@ -77,9 +77,13 @@
 #ifndef PCI_DEVICE_ID_ARECA_1203
 #define PCI_DEVICE_ID_ARECA_1203	0x1203
 #endif
+#ifndef PCI_DEVICE_ID_ARECA_1883
+#define PCI_DEVICE_ID_ARECA_1883	0x1883
+#endif
 #ifndef PCI_DEVICE_ID_ARECA_1884
 #define PCI_DEVICE_ID_ARECA_1884	0x1884
 #endif
+#define PCI_DEVICE_ID_ARECA_1886_0	0x1886
 #define PCI_DEVICE_ID_ARECA_1886	0x188A
 #define	ARCMSR_HOURS			(1000 * 60 * 60 * 4)
 #define	ARCMSR_MINUTES			(1000 * 60 * 60)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/arcmsr/arcmsr_hba.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/arcmsr/arcmsr_hba.c
@@ -214,8 +214,12 @@
 		.driver_data = ACB_ADAPTER_TYPE_A},
 	{PCI_DEVICE(PCI_VENDOR_ID_ARECA, PCI_DEVICE_ID_ARECA_1880),
 		.driver_data = ACB_ADAPTER_TYPE_C},
+	{PCI_DEVICE(PCI_VENDOR_ID_ARECA, PCI_DEVICE_ID_ARECA_1883),
+		.driver_data = ACB_ADAPTER_TYPE_C},
 	{PCI_DEVICE(PCI_VENDOR_ID_ARECA, PCI_DEVICE_ID_ARECA_1884),
 		.driver_data = ACB_ADAPTER_TYPE_E},
+	{PCI_DEVICE(PCI_VENDOR_ID_ARECA, PCI_DEVICE_ID_ARECA_1886_0),
+		.driver_data = ACB_ADAPTER_TYPE_F},
 	{PCI_DEVICE(PCI_VENDOR_ID_ARECA, PCI_DEVICE_ID_ARECA_1886),
 		.driver_data = ACB_ADAPTER_TYPE_F},
 	{0, 0}, /* Terminating entry */
@@ -4710,9 +4714,11 @@
 	case PCI_DEVICE_ID_ARECA_1680:
 	case PCI_DEVICE_ID_ARECA_1681:
 	case PCI_DEVICE_ID_ARECA_1880:
+	case PCI_DEVICE_ID_ARECA_1883:
 	case PCI_DEVICE_ID_ARECA_1884:
 		type = "SAS/SATA";
 		break;
+	case PCI_DEVICE_ID_ARECA_1886_0:
 	case PCI_DEVICE_ID_ARECA_1886:
 		type = "NVMe/SAS/SATA";
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/atari_scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/atari_scsi.c
@@ -538,7 +538,7 @@
 static int atari_scsi_dma_xfer_len(struct NCR5380_hostdata *hostdata,
                                    struct scsi_cmnd *cmd)
 {
-	int wanted_len = cmd->SCp.this_residual;
+	int wanted_len = NCR5380_to_ncmd(cmd)->this_residual;
 	int possible_len, limit;
 
 	if (wanted_len < DMA_MIN_SIZE)
@@ -610,7 +610,7 @@
 	}
 
 	/* Last step: apply the hard limit on DMA transfers */
-	limit = (atari_dma_buffer && !STRAM_ADDR(virt_to_phys(cmd->SCp.ptr))) ?
+	limit = (atari_dma_buffer && !STRAM_ADDR(virt_to_phys(NCR5380_to_ncmd(cmd)->ptr))) ?
 		    STRAM_BUFFER_SIZE : 255*512;
 	if (possible_len > limit)
 		possible_len = limit;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/be2iscsi/be_iscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/be2iscsi/be_iscsi.c
@@ -450,6 +450,10 @@
 	}
 
 	nla_for_each_attr(attrib, data, dt_len, rm_len) {
+		/* ignore nla_type as it is never used */
+		if (nla_len(attrib) < sizeof(*iface_param))
+			return -EINVAL;
+
 		iface_param = nla_data(attrib);
 
 		if (iface_param->param_type != ISCSI_NET_PARAM)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/be2iscsi/be_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/be2iscsi/be_main.c
@@ -2691,6 +2691,7 @@
 		kfree(pwrb_context->pwrb_handle_base);
 		kfree(pwrb_context->pwrb_handle_basestd);
 	}
+	kfree(phwi_ctxt->be_wrbq);
 	return -ENOMEM;
 }
 
@@ -5741,7 +5742,7 @@
 	cancel_work_sync(&phba->sess_work);
 
 	beiscsi_iface_destroy_default(phba);
-	iscsi_host_remove(phba->shost);
+	iscsi_host_remove(phba->shost, false);
 	beiscsi_disable_port(phba, 1);
 
 	/* after cancelling boot_work */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfa.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfa.h
@@ -20,7 +20,6 @@
 struct bfa_s;
 
 typedef void (*bfa_isr_func_t) (struct bfa_s *bfa, struct bfi_msg_s *m);
-typedef void (*bfa_cb_cbfn_status_t) (void *cbarg, bfa_status_t status);
 
 /*
  * Interrupt message handlers
@@ -435,6 +434,14 @@
 	(__qe)->hcb_qe.cbarg = (__cbarg);			\
 	(__qe)->hcb_qe.pre_rmv = BFA_TRUE;			\
 	(__qe)->data = (__data);				\
+} while (0)
+
+#define bfa_pending_q_init_status(__qe, __cbfn, __cbarg, __data) do {	\
+	bfa_q_qe_init(&((__qe)->hcb_qe.qe));			\
+	(__qe)->hcb_qe.cbfn_status = (__cbfn);			\
+	(__qe)->hcb_qe.cbarg = (__cbarg);			\
+	(__qe)->hcb_qe.pre_rmv = BFA_TRUE;			\
+	(__qe)->data = (__data);				\
 } while (0)
 
 #endif /* __BFA_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfa_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfa_core.c
@@ -1907,15 +1907,13 @@
 	struct list_head		*qe;
 	struct list_head		*qen;
 	struct bfa_cb_qe_s	*hcb_qe;
-	bfa_cb_cbfn_status_t	cbfn;
 
 	list_for_each_safe(qe, qen, comp_q) {
 		hcb_qe = (struct bfa_cb_qe_s *) qe;
 		if (hcb_qe->pre_rmv) {
 			/* qe is invalid after return, dequeue before cbfn() */
 			list_del(qe);
-			cbfn = (bfa_cb_cbfn_status_t)(hcb_qe->cbfn);
-			cbfn(hcb_qe->cbarg, hcb_qe->fw_status);
+			hcb_qe->cbfn_status(hcb_qe->cbarg, hcb_qe->fw_status);
 		} else
 			hcb_qe->cbfn(hcb_qe->cbarg, BFA_TRUE);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfa_ioc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfa_ioc.h
@@ -361,14 +361,18 @@
 	void	*cbarg;
 };
 
-typedef void	(*bfa_cb_cbfn_t) (void *cbarg, bfa_boolean_t complete);
+typedef void (*bfa_cb_cbfn_t) (void *cbarg, bfa_boolean_t complete);
+typedef void (*bfa_cb_cbfn_status_t) (void *cbarg, bfa_status_t status);
 
 /*
  * Generic BFA callback element.
  */
 struct bfa_cb_qe_s {
 	struct list_head	qe;
-	bfa_cb_cbfn_t	cbfn;
+	union {
+		bfa_cb_cbfn_status_t	cbfn_status;
+		bfa_cb_cbfn_t		cbfn;
+	};
 	bfa_boolean_t	once;
 	bfa_boolean_t	pre_rmv;	/* set for stack based qe(s) */
 	bfa_status_t	fw_status;	/* to access fw status in comp proc */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfad.c
@@ -1705,9 +1705,8 @@
 
 	error = bfad_im_module_init();
 	if (error) {
-		error = -ENOMEM;
 		printk(KERN_WARNING "bfad_im_module_init failure\n");
-		goto ext;
+		return -ENOMEM;
 	}
 
 	if (strcmp(FCPI_NAME, " fcpim") == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfad_attr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfad_attr.c
@@ -711,7 +711,7 @@
 	char serial_num[BFA_ADAPTER_SERIAL_NUM_LEN];
 
 	bfa_get_adapter_serial_num(&bfad->bfa, serial_num);
-	return snprintf(buf, PAGE_SIZE, "%s\n", serial_num);
+	return sysfs_emit(buf, "%s\n", serial_num);
 }
 
 static ssize_t
@@ -725,7 +725,7 @@
 	char model[BFA_ADAPTER_MODEL_NAME_LEN];
 
 	bfa_get_adapter_model(&bfad->bfa, model);
-	return snprintf(buf, PAGE_SIZE, "%s\n", model);
+	return sysfs_emit(buf, "%s\n", model);
 }
 
 static ssize_t
@@ -805,7 +805,7 @@
 		snprintf(model_descr, BFA_ADAPTER_MODEL_DESCR_LEN,
 			"Invalid Model");
 
-	return snprintf(buf, PAGE_SIZE, "%s\n", model_descr);
+	return sysfs_emit(buf, "%s\n", model_descr);
 }
 
 static ssize_t
@@ -819,7 +819,7 @@
 	u64        nwwn;
 
 	nwwn = bfa_fcs_lport_get_nwwn(port->fcs_port);
-	return snprintf(buf, PAGE_SIZE, "0x%llx\n", cpu_to_be64(nwwn));
+	return sysfs_emit(buf, "0x%llx\n", cpu_to_be64(nwwn));
 }
 
 static ssize_t
@@ -836,7 +836,7 @@
 	bfa_fcs_lport_get_attr(&bfad->bfa_fcs.fabric.bport, &port_attr);
 	strlcpy(symname, port_attr.port_cfg.sym_name.symname,
 			BFA_SYMNAME_MAXLEN);
-	return snprintf(buf, PAGE_SIZE, "%s\n", symname);
+	return sysfs_emit(buf, "%s\n", symname);
 }
 
 static ssize_t
@@ -850,14 +850,14 @@
 	char hw_ver[BFA_VERSION_LEN];
 
 	bfa_get_pci_chip_rev(&bfad->bfa, hw_ver);
-	return snprintf(buf, PAGE_SIZE, "%s\n", hw_ver);
+	return sysfs_emit(buf, "%s\n", hw_ver);
 }
 
 static ssize_t
 bfad_im_drv_version_show(struct device *dev, struct device_attribute *attr,
 				char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%s\n", BFAD_DRIVER_VERSION);
+	return sysfs_emit(buf, "%s\n", BFAD_DRIVER_VERSION);
 }
 
 static ssize_t
@@ -871,7 +871,7 @@
 	char optrom_ver[BFA_VERSION_LEN];
 
 	bfa_get_adapter_optrom_ver(&bfad->bfa, optrom_ver);
-	return snprintf(buf, PAGE_SIZE, "%s\n", optrom_ver);
+	return sysfs_emit(buf, "%s\n", optrom_ver);
 }
 
 static ssize_t
@@ -885,7 +885,7 @@
 	char fw_ver[BFA_VERSION_LEN];
 
 	bfa_get_adapter_fw_ver(&bfad->bfa, fw_ver);
-	return snprintf(buf, PAGE_SIZE, "%s\n", fw_ver);
+	return sysfs_emit(buf, "%s\n", fw_ver);
 }
 
 static ssize_t
@@ -897,7 +897,7 @@
 			(struct bfad_im_port_s *) shost->hostdata[0];
 	struct bfad_s *bfad = im_port->bfad;
 
-	return snprintf(buf, PAGE_SIZE, "%d\n",
+	return sysfs_emit(buf, "%d\n",
 			bfa_get_nports(&bfad->bfa));
 }
 
@@ -905,7 +905,7 @@
 bfad_im_drv_name_show(struct device *dev, struct device_attribute *attr,
 				char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%s\n", BFAD_DRIVER_NAME);
+	return sysfs_emit(buf, "%s\n", BFAD_DRIVER_NAME);
 }
 
 static ssize_t
@@ -924,14 +924,14 @@
 	rports = kcalloc(nrports, sizeof(struct bfa_rport_qualifier_s),
 			 GFP_ATOMIC);
 	if (rports == NULL)
-		return snprintf(buf, PAGE_SIZE, "Failed\n");
+		return sysfs_emit(buf, "Failed\n");
 
 	spin_lock_irqsave(&bfad->bfad_lock, flags);
 	bfa_fcs_lport_get_rport_quals(port->fcs_port, rports, &nrports);
 	spin_unlock_irqrestore(&bfad->bfad_lock, flags);
 	kfree(rports);
 
-	return snprintf(buf, PAGE_SIZE, "%d\n", nrports);
+	return sysfs_emit(buf, "%d\n", nrports);
 }
 
 static          DEVICE_ATTR(serial_number, S_IRUGO,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfad_bsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfad_bsg.c
@@ -2135,8 +2135,7 @@
 	struct bfa_cb_pending_q_s cb_qe;
 
 	init_completion(&fcomp.comp);
-	bfa_pending_q_init(&cb_qe, (bfa_cb_cbfn_t)bfad_hcb_comp,
-			   &fcomp, &iocmd->stats);
+	bfa_pending_q_init_status(&cb_qe, bfad_hcb_comp, &fcomp, &iocmd->stats);
 	spin_lock_irqsave(&bfad->bfad_lock, flags);
 	iocmd->status = bfa_fcport_get_stats(&bfad->bfa, &cb_qe);
 	spin_unlock_irqrestore(&bfad->bfad_lock, flags);
@@ -2159,7 +2158,7 @@
 	struct bfa_cb_pending_q_s cb_qe;
 
 	init_completion(&fcomp.comp);
-	bfa_pending_q_init(&cb_qe, (bfa_cb_cbfn_t)bfad_hcb_comp, &fcomp, NULL);
+	bfa_pending_q_init_status(&cb_qe, bfad_hcb_comp, &fcomp, NULL);
 
 	spin_lock_irqsave(&bfad->bfad_lock, flags);
 	iocmd->status = bfa_fcport_clear_stats(&bfad->bfa, &cb_qe);
@@ -2443,8 +2442,7 @@
 	struct bfa_fcport_s *fcport = BFA_FCPORT_MOD(&bfad->bfa);
 
 	init_completion(&fcomp.comp);
-	bfa_pending_q_init(&cb_qe, (bfa_cb_cbfn_t)bfad_hcb_comp,
-			   &fcomp, &iocmd->stats);
+	bfa_pending_q_init_status(&cb_qe, bfad_hcb_comp, &fcomp, &iocmd->stats);
 
 	spin_lock_irqsave(&bfad->bfad_lock, flags);
 	WARN_ON(!bfa_ioc_get_fcmode(&bfad->bfa.ioc));
@@ -2474,8 +2472,7 @@
 	struct bfa_fcport_s *fcport = BFA_FCPORT_MOD(&bfad->bfa);
 
 	init_completion(&fcomp.comp);
-	bfa_pending_q_init(&cb_qe, (bfa_cb_cbfn_t)bfad_hcb_comp,
-			   &fcomp, NULL);
+	bfa_pending_q_init_status(&cb_qe, bfad_hcb_comp, &fcomp, NULL);
 
 	spin_lock_irqsave(&bfad->bfad_lock, flags);
 	WARN_ON(!bfa_ioc_get_fcmode(&bfad->bfa.ioc));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bfa/bfad_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bfa/bfad_debugfs.c
@@ -250,7 +250,7 @@
 	unsigned long flags;
 	void *kern_buf;
 
-	kern_buf = memdup_user(buf, nbytes);
+	kern_buf = memdup_user_nul(buf, nbytes);
 	if (IS_ERR(kern_buf))
 		return PTR_ERR(kern_buf);
 
@@ -317,7 +317,7 @@
 	unsigned long flags;
 	void *kern_buf;
 
-	kern_buf = memdup_user(buf, nbytes);
+	kern_buf = memdup_user_nul(buf, nbytes);
 	if (IS_ERR(kern_buf))
 		return PTR_ERR(kern_buf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bnx2fc/bnx2fc_fcoe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bnx2fc/bnx2fc_fcoe.c
@@ -82,7 +82,7 @@
 static void bnx2fc_unbind_pcidev(struct bnx2fc_hba *hba);
 static struct fc_lport *bnx2fc_if_create(struct bnx2fc_interface *interface,
 				  struct device *parent, int npiv);
-static void bnx2fc_destroy_work(struct work_struct *work);
+static void bnx2fc_port_destroy(struct fcoe_port *port);
 
 static struct bnx2fc_hba *bnx2fc_hba_lookup(struct net_device *phys_dev);
 static struct bnx2fc_interface *bnx2fc_interface_lookup(struct net_device
@@ -432,7 +432,6 @@
 	struct fcoe_ctlr *ctlr;
 	struct fcoe_rcv_info *fr;
 	struct fcoe_percpu_s *bg;
-	struct sk_buff *tmp_skb;
 
 	interface = container_of(ptype, struct bnx2fc_interface,
 				 fcoe_packet_type);
@@ -444,11 +443,9 @@
 		goto err;
 	}
 
-	tmp_skb = skb_share_check(skb, GFP_ATOMIC);
-	if (!tmp_skb)
-		goto err;
-
-	skb = tmp_skb;
+	skb = skb_share_check(skb, GFP_ATOMIC);
+	if (!skb)
+		return -1;
 
 	if (unlikely(eth_hdr(skb)->h_proto != htons(ETH_P_FCOE))) {
 		printk(KERN_ERR PFX "bnx2fc_rcv: Wrong FC type frame\n");
@@ -508,7 +505,8 @@
 
 static void bnx2fc_recv_frame(struct sk_buff *skb)
 {
-	u32 fr_len;
+	u64 crc_err;
+	u32 fr_len, fr_crc;
 	struct fc_lport *lport;
 	struct fcoe_rcv_info *fr;
 	struct fc_stats *stats;
@@ -542,6 +540,11 @@
 	skb_pull(skb, sizeof(struct fcoe_hdr));
 	fr_len = skb->len - sizeof(struct fcoe_crc_eof);
 
+	stats = per_cpu_ptr(lport->stats, get_cpu());
+	stats->RxFrames++;
+	stats->RxWords += fr_len / FCOE_WORD_TO_BYTE;
+	put_cpu();
+
 	fp = (struct fc_frame *)skb;
 	fc_frame_init(fp);
 	fr_dev(fp) = lport;
@@ -624,16 +627,15 @@
 		return;
 	}
 
-	stats = per_cpu_ptr(lport->stats, smp_processor_id());
-	stats->RxFrames++;
-	stats->RxWords += fr_len / FCOE_WORD_TO_BYTE;
+	fr_crc = le32_to_cpu(fr_crc(fp));
 
-	if (le32_to_cpu(fr_crc(fp)) !=
-			~crc32(~0, skb->data, fr_len)) {
-		if (stats->InvalidCRCCount < 5)
+	if (unlikely(fr_crc != ~crc32(~0, skb->data, fr_len))) {
+		stats = per_cpu_ptr(lport->stats, get_cpu());
+		crc_err = (stats->InvalidCRCCount++);
+		put_cpu();
+		if (crc_err < 5)
 			printk(KERN_WARNING PFX "dropping frame with "
 			       "CRC error\n");
-		stats->InvalidCRCCount++;
 		kfree_skb(skb);
 		return;
 	}
@@ -907,9 +909,6 @@
 				__bnx2fc_destroy(interface);
 		}
 		mutex_unlock(&bnx2fc_dev_lock);
-
-		/* Ensure ALL destroy work has been completed before return */
-		flush_workqueue(bnx2fc_wq);
 		return;
 
 	default:
@@ -1215,8 +1214,8 @@
 	mutex_unlock(&n_port->lp_mutex);
 	bnx2fc_free_vport(interface->hba, port->lport);
 	bnx2fc_port_shutdown(port->lport);
+	bnx2fc_port_destroy(port);
 	bnx2fc_interface_put(interface);
-	queue_work(bnx2fc_wq, &port->destroy_work);
 	return 0;
 }
 
@@ -1525,7 +1524,6 @@
 	port->lport = lport;
 	port->priv = interface;
 	port->get_netdev = bnx2fc_netdev;
-	INIT_WORK(&port->destroy_work, bnx2fc_destroy_work);
 
 	/* Configure fcoe_port */
 	rc = bnx2fc_lport_config(lport);
@@ -1653,8 +1651,8 @@
 	bnx2fc_interface_cleanup(interface);
 	bnx2fc_stop(interface);
 	list_del(&interface->list);
+	bnx2fc_port_destroy(port);
 	bnx2fc_interface_put(interface);
-	queue_work(bnx2fc_wq, &port->destroy_work);
 }
 
 /**
@@ -1694,15 +1692,12 @@
 	return rc;
 }
 
-static void bnx2fc_destroy_work(struct work_struct *work)
+static void bnx2fc_port_destroy(struct fcoe_port *port)
 {
-	struct fcoe_port *port;
 	struct fc_lport *lport;
 
-	port = container_of(work, struct fcoe_port, destroy_work);
 	lport = port->lport;
-
-	BNX2FC_HBA_DBG(lport, "Entered bnx2fc_destroy_work\n");
+	BNX2FC_HBA_DBG(lport, "Entered %s, destroying lport %p\n", __func__, lport);
 
 	bnx2fc_if_destroy(lport);
 }
@@ -2556,9 +2551,6 @@
 			__bnx2fc_destroy(interface);
 	mutex_unlock(&bnx2fc_dev_lock);
 
-	/* Ensure ALL destroy work has been completed before return */
-	flush_workqueue(bnx2fc_wq);
-
 	bnx2fc_ulp_stop(hba);
 	/* unregister cnic device */
 	if (test_and_clear_bit(BNX2FC_CNIC_REGISTERED, &hba->reg_with_cnic))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bnx2fc/bnx2fc_tgt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bnx2fc/bnx2fc_tgt.c
@@ -833,7 +833,6 @@
 
 	BNX2FC_TGT_DBG(tgt, "Freeing up session resources\n");
 
-	spin_lock_bh(&tgt->cq_lock);
 	ctx_base_ptr = tgt->ctx_base;
 	tgt->ctx_base = NULL;
 
@@ -889,7 +888,6 @@
 				    tgt->sq, tgt->sq_dma);
 		tgt->sq = NULL;
 	}
-	spin_unlock_bh(&tgt->cq_lock);
 
 	if (ctx_base_ptr)
 		iounmap(ctx_base_ptr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bnx2i/bnx2i_hwi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bnx2i/bnx2i_hwi.c
@@ -1977,7 +1977,7 @@
 		if (nopin->cq_req_sn != qp->cqe_exp_seq_sn)
 			break;
 
-		if (unlikely(test_bit(ISCSI_SUSPEND_BIT, &conn->suspend_rx))) {
+		if (unlikely(test_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags))) {
 			if (nopin->op_code == ISCSI_OP_NOOP_IN &&
 			    nopin->itt == (u16) RESERVED_ITT) {
 				printk(KERN_ALERT "bnx2i: Unsolicited "
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/bnx2i/bnx2i_iscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/bnx2i/bnx2i_iscsi.c
@@ -909,7 +909,7 @@
 {
 	struct Scsi_Host *shost = hba->shost;
 
-	iscsi_host_remove(shost);
+	iscsi_host_remove(shost, false);
 	INIT_LIST_HEAD(&hba->ep_ofld_list);
 	INIT_LIST_HEAD(&hba->ep_active_list);
 	INIT_LIST_HEAD(&hba->ep_destroy_list);
@@ -1721,7 +1721,7 @@
 			struct iscsi_conn *conn = ep->conn->cls_conn->dd_data;
 
 			/* Must suspend all rx queue activity for this ep */
-			set_bit(ISCSI_SUSPEND_BIT, &conn->suspend_rx);
+			set_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags);
 		}
 		/* CONN_DISCONNECT timeout may or may not be an issue depending
 		 * on what transcribed in TCP layer, different targets behave
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/csiostor/csio_defs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/csiostor/csio_defs.h
@@ -73,7 +73,21 @@
 #define csio_list_prev(elem)	(((struct list_head *)(elem))->prev)
 
 /* State machine */
-typedef void (*csio_sm_state_t)(void *, uint32_t);
+struct csio_lnode;
+
+/* State machine evets */
+enum csio_ln_ev {
+	CSIO_LNE_NONE = (uint32_t)0,
+	CSIO_LNE_LINKUP,
+	CSIO_LNE_FAB_INIT_DONE,
+	CSIO_LNE_LINK_DOWN,
+	CSIO_LNE_DOWN_LINK,
+	CSIO_LNE_LOGO,
+	CSIO_LNE_CLOSE,
+	CSIO_LNE_MAX_EVENT,
+};
+
+typedef void (*csio_sm_state_t)(struct csio_lnode *ln, enum csio_ln_ev evt);
 
 struct csio_sm {
 	struct list_head	sm_list;
@@ -83,7 +97,7 @@
 static inline void
 csio_set_state(void *smp, void *state)
 {
-	((struct csio_sm *)smp)->sm_state = (csio_sm_state_t)state;
+	((struct csio_sm *)smp)->sm_state = state;
 }
 
 static inline void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/csiostor/csio_lnode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/csiostor/csio_lnode.c
@@ -619,7 +619,7 @@
 	struct fc_els_csp *csp;
 	struct fc_els_cssp *clsp;
 	enum fw_retval retval;
-	__be32 nport_id;
+	__be32 nport_id = 0;
 
 	retval = FW_CMD_RETVAL_G(ntohl(rsp->alloc_to_len16));
 	if (retval != FW_SUCCESS) {
@@ -1095,7 +1095,7 @@
 int
 csio_is_lnode_ready(struct csio_lnode *ln)
 {
-	return (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready));
+	return (csio_get_state(ln) == csio_lns_ready);
 }
 
 /*****************************************************************************/
@@ -1366,15 +1366,15 @@
 void
 csio_lnode_state_to_str(struct csio_lnode *ln, int8_t *str)
 {
-	if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_uninit)) {
+	if (csio_get_state(ln) == csio_lns_uninit) {
 		strcpy(str, "UNINIT");
 		return;
 	}
-	if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready)) {
+	if (csio_get_state(ln) == csio_lns_ready) {
 		strcpy(str, "READY");
 		return;
 	}
-	if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_offline)) {
+	if (csio_get_state(ln) == csio_lns_offline) {
 		strcpy(str, "OFFLINE");
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/csiostor/csio_lnode.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/csiostor/csio_lnode.h
@@ -53,19 +53,6 @@
 extern int csio_fcoe_rnodes;
 extern int csio_fdmi_enable;
 
-/* State machine evets */
-enum csio_ln_ev {
-	CSIO_LNE_NONE = (uint32_t)0,
-	CSIO_LNE_LINKUP,
-	CSIO_LNE_FAB_INIT_DONE,
-	CSIO_LNE_LINK_DOWN,
-	CSIO_LNE_DOWN_LINK,
-	CSIO_LNE_LOGO,
-	CSIO_LNE_CLOSE,
-	CSIO_LNE_MAX_EVENT,
-};
-
-
 struct csio_fcf_info {
 	struct list_head	list;
 	uint8_t			priority;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/cxgbi/libcxgbi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/cxgbi/libcxgbi.c
@@ -328,7 +328,7 @@
 		chba = cdev->hbas[i];
 		if (chba) {
 			cdev->hbas[i] = NULL;
-			iscsi_host_remove(chba->shost);
+			iscsi_host_remove(chba->shost, false);
 			pci_dev_put(cdev->pdev);
 			iscsi_host_free(chba->shost);
 		}
@@ -1455,7 +1455,7 @@
 	if (conn) {
 		log_debug(1 << CXGBI_DBG_SOCK,
 			"csk 0x%p, cid %d.\n", csk, conn->id);
-		iscsi_conn_queue_work(conn);
+		iscsi_conn_queue_xmit(conn);
 	}
 }
 EXPORT_SYMBOL_GPL(cxgbi_conn_tx_open);
@@ -1634,11 +1634,11 @@
 	log_debug(1 << CXGBI_DBG_PDU_RX,
 		"csk 0x%p, conn 0x%p.\n", csk, conn);
 
-	if (unlikely(!conn || conn->suspend_rx)) {
+	if (unlikely(!conn || test_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags))) {
 		log_debug(1 << CXGBI_DBG_PDU_RX,
-			"csk 0x%p, conn 0x%p, id %d, suspend_rx %lu!\n",
+			"csk 0x%p, conn 0x%p, id %d, conn flags 0x%lx!\n",
 			csk, conn, conn ? conn->id : 0xFF,
-			conn ? conn->suspend_rx : 0xFF);
+			conn ? conn->flags : 0xFF);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/dc395x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/dc395x.c
@@ -3590,10 +3590,19 @@
 #endif
 	if (dcb->target_lun != 0) {
 		/* Copy settings */
-		struct DeviceCtlBlk *p;
-		list_for_each_entry(p, &acb->dcb_list, list)
-			if (p->target_id == dcb->target_id)
+		struct DeviceCtlBlk *p = NULL, *iter;
+
+		list_for_each_entry(iter, &acb->dcb_list, list)
+			if (iter->target_id == dcb->target_id) {
+				p = iter;
 				break;
+			}
+
+		if (!p) {
+			kfree(dcb);
+			return NULL;
+		}
+
 		dprintkdbg(DBG_1, 
 		       "device_alloc: <%02i-%i> copy from <%02i-%i>\n",
 		       dcb->target_id, dcb->target_lun,
@@ -4618,6 +4627,7 @@
 	/* initialise the adapter and everything we need */
  	if (adapter_init(acb, io_port_base, io_port_len, irq)) {
 		dprintkl(KERN_INFO, "adapter init failed\n");
+		acb = NULL;
 		goto fail;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/device_handler/scsi_dh_alua.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/device_handler/scsi_dh_alua.c
@@ -406,28 +406,40 @@
 	}
 }
 
-static enum scsi_disposition alua_check_sense(struct scsi_device *sdev,
-					      struct scsi_sense_hdr *sense_hdr)
+static void alua_handle_state_transition(struct scsi_device *sdev)
 {
 	struct alua_dh_data *h = sdev->handler_data;
 	struct alua_port_group *pg;
 
+	rcu_read_lock();
+	pg = rcu_dereference(h->pg);
+	if (pg)
+		pg->state = SCSI_ACCESS_STATE_TRANSITIONING;
+	rcu_read_unlock();
+	alua_check(sdev, false);
+}
+
+static enum scsi_disposition alua_check_sense(struct scsi_device *sdev,
+					      struct scsi_sense_hdr *sense_hdr)
+{
 	switch (sense_hdr->sense_key) {
 	case NOT_READY:
 		if (sense_hdr->asc == 0x04 && sense_hdr->ascq == 0x0a) {
 			/*
 			 * LUN Not Accessible - ALUA state transition
 			 */
-			rcu_read_lock();
-			pg = rcu_dereference(h->pg);
-			if (pg)
-				pg->state = SCSI_ACCESS_STATE_TRANSITIONING;
-			rcu_read_unlock();
-			alua_check(sdev, false);
+			alua_handle_state_transition(sdev);
 			return NEEDS_RETRY;
 		}
 		break;
 	case UNIT_ATTENTION:
+		if (sense_hdr->asc == 0x04 && sense_hdr->ascq == 0x0a) {
+			/*
+			 * LUN Not Accessible - ALUA state transition
+			 */
+			alua_handle_state_transition(sdev);
+			return NEEDS_RETRY;
+		}
 		if (sense_hdr->asc == 0x29 && sense_hdr->ascq == 0x00) {
 			/*
 			 * Power On, Reset, or Bus Device Reset.
@@ -494,7 +506,8 @@
 
 	retval = scsi_test_unit_ready(sdev, ALUA_FAILOVER_TIMEOUT * HZ,
 				      ALUA_FAILOVER_RETRIES, &sense_hdr);
-	if (sense_hdr.sense_key == NOT_READY &&
+	if ((sense_hdr.sense_key == NOT_READY ||
+	     sense_hdr.sense_key == UNIT_ATTENTION) &&
 	    sense_hdr.asc == 0x04 && sense_hdr.ascq == 0x0a)
 		return SCSI_DH_RETRY;
 	else if (retval)
@@ -1117,10 +1130,12 @@
 	rcu_read_unlock();
 	mutex_unlock(&h->init_mutex);
 
-	if (alua_rtpg_queue(pg, sdev, qdata, true))
+	if (alua_rtpg_queue(pg, sdev, qdata, true)) {
 		fn = NULL;
-	else
+	} else {
+		kfree(qdata);
 		err = SCSI_DH_DEV_OFFLINED;
+	}
 	kref_put(&pg->kref, release_port_group);
 out:
 	if (fn)
@@ -1172,9 +1187,8 @@
 	case SCSI_ACCESS_STATE_OPTIMAL:
 	case SCSI_ACCESS_STATE_ACTIVE:
 	case SCSI_ACCESS_STATE_LBA:
-		return BLK_STS_OK;
 	case SCSI_ACCESS_STATE_TRANSITIONING:
-		return BLK_STS_AGAIN;
+		return BLK_STS_OK;
 	default:
 		req->rq_flags |= RQF_QUIET;
 		return BLK_STS_IOERR;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/dpt_i2o.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/dpt_i2o.c
@@ -56,7 +56,7 @@
 #include <linux/mutex.h>
 
 #include <asm/processor.h>	/* for boot_cpu_data */
-#include <asm/io.h>		/* for virt_to_bus, etc. */
+#include <asm/io.h>
 
 #include <scsi/scsi.h>
 #include <scsi/scsi_cmnd.h>
@@ -582,51 +582,6 @@
 	return 0;
 }
 
-/*
- *	Turn a pointer to ioctl reply data into an u32 'context'
- */
-static u32 adpt_ioctl_to_context(adpt_hba * pHba, void *reply)
-{
-#if BITS_PER_LONG == 32
-	return (u32)(unsigned long)reply;
-#else
-	ulong flags = 0;
-	u32 nr, i;
-
-	spin_lock_irqsave(pHba->host->host_lock, flags);
-	nr = ARRAY_SIZE(pHba->ioctl_reply_context);
-	for (i = 0; i < nr; i++) {
-		if (pHba->ioctl_reply_context[i] == NULL) {
-			pHba->ioctl_reply_context[i] = reply;
-			break;
-		}
-	}
-	spin_unlock_irqrestore(pHba->host->host_lock, flags);
-	if (i >= nr) {
-		printk(KERN_WARNING"%s: Too many outstanding "
-				"ioctl commands\n", pHba->name);
-		return (u32)-1;
-	}
-
-	return i;
-#endif
-}
-
-/*
- *	Go from an u32 'context' to a pointer to ioctl reply data.
- */
-static void *adpt_ioctl_from_context(adpt_hba *pHba, u32 context)
-{
-#if BITS_PER_LONG == 32
-	return (void *)(unsigned long)context;
-#else
-	void *p = pHba->ioctl_reply_context[context];
-	pHba->ioctl_reply_context[context] = NULL;
-
-	return p;
-#endif
-}
-
 /*===========================================================================
  * Error Handling routines
  *===========================================================================
@@ -1648,208 +1603,6 @@
 	return 0;
 }
 
-
-static int adpt_i2o_passthru(adpt_hba* pHba, u32 __user *arg)
-{
-	u32 msg[MAX_MESSAGE_SIZE];
-	u32* reply = NULL;
-	u32 size = 0;
-	u32 reply_size = 0;
-	u32 __user *user_msg = arg;
-	u32 __user * user_reply = NULL;
-	void **sg_list = NULL;
-	u32 sg_offset = 0;
-	u32 sg_count = 0;
-	int sg_index = 0;
-	u32 i = 0;
-	u32 rcode = 0;
-	void *p = NULL;
-	dma_addr_t addr;
-	ulong flags = 0;
-
-	memset(&msg, 0, MAX_MESSAGE_SIZE*4);
-	// get user msg size in u32s 
-	if(get_user(size, &user_msg[0])){
-		return -EFAULT;
-	}
-	size = size>>16;
-
-	user_reply = &user_msg[size];
-	if(size > MAX_MESSAGE_SIZE){
-		return -EFAULT;
-	}
-	size *= 4; // Convert to bytes
-
-	/* Copy in the user's I2O command */
-	if(copy_from_user(msg, user_msg, size)) {
-		return -EFAULT;
-	}
-	get_user(reply_size, &user_reply[0]);
-	reply_size = reply_size>>16;
-	if(reply_size > REPLY_FRAME_SIZE){
-		reply_size = REPLY_FRAME_SIZE;
-	}
-	reply_size *= 4;
-	reply = kzalloc(REPLY_FRAME_SIZE*4, GFP_KERNEL);
-	if(reply == NULL) {
-		printk(KERN_WARNING"%s: Could not allocate reply buffer\n",pHba->name);
-		return -ENOMEM;
-	}
-	sg_offset = (msg[0]>>4)&0xf;
-	msg[2] = 0x40000000; // IOCTL context
-	msg[3] = adpt_ioctl_to_context(pHba, reply);
-	if (msg[3] == (u32)-1) {
-		rcode = -EBUSY;
-		goto free;
-	}
-
-	sg_list = kcalloc(pHba->sg_tablesize, sizeof(*sg_list), GFP_KERNEL);
-	if (!sg_list) {
-		rcode = -ENOMEM;
-		goto free;
-	}
-	if(sg_offset) {
-		// TODO add 64 bit API
-		struct sg_simple_element *sg =  (struct sg_simple_element*) (msg+sg_offset);
-		sg_count = (size - sg_offset*4) / sizeof(struct sg_simple_element);
-		if (sg_count > pHba->sg_tablesize){
-			printk(KERN_DEBUG"%s:IOCTL SG List too large (%u)\n", pHba->name,sg_count);
-			rcode = -EINVAL;
-			goto free;
-		}
-
-		for(i = 0; i < sg_count; i++) {
-			int sg_size;
-
-			if (!(sg[i].flag_count & 0x10000000 /*I2O_SGL_FLAGS_SIMPLE_ADDRESS_ELEMENT*/)) {
-				printk(KERN_DEBUG"%s:Bad SG element %d - not simple (%x)\n",pHba->name,i,  sg[i].flag_count);
-				rcode = -EINVAL;
-				goto cleanup;
-			}
-			sg_size = sg[i].flag_count & 0xffffff;      
-			/* Allocate memory for the transfer */
-			p = dma_alloc_coherent(&pHba->pDev->dev, sg_size, &addr, GFP_KERNEL);
-			if(!p) {
-				printk(KERN_DEBUG"%s: Could not allocate SG buffer - size = %d buffer number %d of %d\n",
-						pHba->name,sg_size,i,sg_count);
-				rcode = -ENOMEM;
-				goto cleanup;
-			}
-			sg_list[sg_index++] = p; // sglist indexed with input frame, not our internal frame.
-			/* Copy in the user's SG buffer if necessary */
-			if(sg[i].flag_count & 0x04000000 /*I2O_SGL_FLAGS_DIR*/) {
-				// sg_simple_element API is 32 bit
-				if (copy_from_user(p,(void __user *)(ulong)sg[i].addr_bus, sg_size)) {
-					printk(KERN_DEBUG"%s: Could not copy SG buf %d FROM user\n",pHba->name,i);
-					rcode = -EFAULT;
-					goto cleanup;
-				}
-			}
-			/* sg_simple_element API is 32 bit, but addr < 4GB */
-			sg[i].addr_bus = addr;
-		}
-	}
-
-	do {
-		/*
-		 * Stop any new commands from enterring the
-		 * controller while processing the ioctl
-		 */
-		if (pHba->host) {
-			scsi_block_requests(pHba->host);
-			spin_lock_irqsave(pHba->host->host_lock, flags);
-		}
-		rcode = adpt_i2o_post_wait(pHba, msg, size, FOREVER);
-		if (rcode != 0)
-			printk("adpt_i2o_passthru: post wait failed %d %p\n",
-					rcode, reply);
-		if (pHba->host) {
-			spin_unlock_irqrestore(pHba->host->host_lock, flags);
-			scsi_unblock_requests(pHba->host);
-		}
-	} while (rcode == -ETIMEDOUT);
-
-	if(rcode){
-		goto cleanup;
-	}
-
-	if(sg_offset) {
-	/* Copy back the Scatter Gather buffers back to user space */
-		u32 j;
-		// TODO add 64 bit API
-		struct sg_simple_element* sg;
-		int sg_size;
-
-		// re-acquire the original message to handle correctly the sg copy operation
-		memset(&msg, 0, MAX_MESSAGE_SIZE*4); 
-		// get user msg size in u32s 
-		if(get_user(size, &user_msg[0])){
-			rcode = -EFAULT; 
-			goto cleanup; 
-		}
-		size = size>>16;
-		size *= 4;
-		if (size > MAX_MESSAGE_SIZE) {
-			rcode = -EINVAL;
-			goto cleanup;
-		}
-		/* Copy in the user's I2O command */
-		if (copy_from_user (msg, user_msg, size)) {
-			rcode = -EFAULT;
-			goto cleanup;
-		}
-		sg_count = (size - sg_offset*4) / sizeof(struct sg_simple_element);
-
-		// TODO add 64 bit API
-		sg 	 = (struct sg_simple_element*)(msg + sg_offset);
-		for (j = 0; j < sg_count; j++) {
-			/* Copy out the SG list to user's buffer if necessary */
-			if(! (sg[j].flag_count & 0x4000000 /*I2O_SGL_FLAGS_DIR*/)) {
-				sg_size = sg[j].flag_count & 0xffffff; 
-				// sg_simple_element API is 32 bit
-				if (copy_to_user((void __user *)(ulong)sg[j].addr_bus,sg_list[j], sg_size)) {
-					printk(KERN_WARNING"%s: Could not copy %p TO user %x\n",pHba->name, sg_list[j], sg[j].addr_bus);
-					rcode = -EFAULT;
-					goto cleanup;
-				}
-			}
-		}
-	} 
-
-	/* Copy back the reply to user space */
-	if (reply_size) {
-		// we wrote our own values for context - now restore the user supplied ones
-		if(copy_from_user(reply+2, user_msg+2, sizeof(u32)*2)) {
-			printk(KERN_WARNING"%s: Could not copy message context FROM user\n",pHba->name);
-			rcode = -EFAULT;
-		}
-		if(copy_to_user(user_reply, reply, reply_size)) {
-			printk(KERN_WARNING"%s: Could not copy reply TO user\n",pHba->name);
-			rcode = -EFAULT;
-		}
-	}
-
-
-cleanup:
-	if (rcode != -ETIME && rcode != -EINTR) {
-		struct sg_simple_element *sg =
-				(struct sg_simple_element*) (msg +sg_offset);
-		while(sg_index) {
-			if(sg_list[--sg_index]) {
-				dma_free_coherent(&pHba->pDev->dev,
-					sg[sg_index].flag_count & 0xffffff,
-					sg_list[sg_index],
-					sg[sg_index].addr_bus);
-			}
-		}
-	}
-
-free:
-	kfree(sg_list);
-	kfree(reply);
-	return rcode;
-}
-
 #if defined __ia64__ 
 static void adpt_ia64_info(sysInfo_S* si)
 {
@@ -1976,8 +1729,6 @@
 			return -EFAULT;
 		}
 		break;
-	case I2OUSRCMD:
-		return adpt_i2o_passthru(pHba, argp);
 
 	case DPT_CTRLINFO:{
 		drvrHBAinfo_S HbaInfo;
@@ -2114,7 +1865,7 @@
 		} else {
 			/* Ick, we should *never* be here */
 			printk(KERN_ERR "dpti: reply frame not from pool\n");
-			reply = (u8 *)bus_to_virt(m);
+			continue;
 		}
 
 		if (readl(reply) & MSG_FAIL) {
@@ -2134,13 +1885,6 @@
 			adpt_send_nop(pHba, old_m);
 		} 
 		context = readl(reply+8);
-		if(context & 0x40000000){ // IOCTL
-			void *p = adpt_ioctl_from_context(pHba, readl(reply+12));
-			if( p != NULL) {
-				memcpy_fromio(p, reply, REPLY_FRAME_SIZE * 4);
-			}
-			// All IOCTLs will also be post wait
-		}
 		if(context & 0x80000000){ // Post wait message
 			status = readl(reply+16);
 			if(status  >> 24){
@@ -2148,16 +1892,14 @@
 			} else {
 				status = I2O_POST_WAIT_OK;
 			}
-			if(!(context & 0x40000000)) {
-				/*
-				 * The request tag is one less than the command tag
-				 * as the firmware might treat a 0 tag as invalid
-				 */
-				cmd = scsi_host_find_tag(pHba->host,
-							 readl(reply + 12) - 1);
-				if(cmd != NULL) {
-					printk(KERN_WARNING"%s: Apparent SCSI cmd in Post Wait Context - cmd=%p context=%x\n", pHba->name, cmd, context);
-				}
+			/*
+			 * The request tag is one less than the command tag
+			 * as the firmware might treat a 0 tag as invalid
+			 */
+			cmd = scsi_host_find_tag(pHba->host,
+						 readl(reply + 12) - 1);
+			if(cmd != NULL) {
+				printk(KERN_WARNING"%s: Apparent SCSI cmd in Post Wait Context - cmd=%p context=%x\n", pHba->name, cmd, context);
 			}
 			adpt_i2o_post_wait_complete(context, status);
 		} else { // SCSI message
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/dpti.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/dpti.h
@@ -248,7 +248,6 @@
 	void __iomem *FwDebugBLEDflag_P;// Virtual Addr Of FW Debug BLED
 	void __iomem *FwDebugBLEDvalue_P;// Virtual Addr Of FW Debug BLED
 	u32 FwDebugFlags;
-	u32 *ioctl_reply_context[4];
 } adpt_hba;
 
 struct sg_simple_element {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/elx/efct/efct_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/elx/efct/efct_driver.c
@@ -42,6 +42,7 @@
 
 	rc = efct_scsi_reg_fc_transport();
 	if (rc) {
+		efct_scsi_tgt_driver_exit();
 		pr_err("failed to register to FC host\n");
 		return rc;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/elx/libefc/efc_els.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/elx/libefc/efc_els.c
@@ -46,18 +46,14 @@
 
 	efc = node->efc;
 
-	spin_lock_irqsave(&node->els_ios_lock, flags);
-
 	if (!node->els_io_enabled) {
 		efc_log_err(efc, "els io alloc disabled\n");
-		spin_unlock_irqrestore(&node->els_ios_lock, flags);
 		return NULL;
 	}
 
 	els = mempool_alloc(efc->els_io_pool, GFP_ATOMIC);
 	if (!els) {
 		atomic_add_return(1, &efc->els_io_alloc_failed_count);
-		spin_unlock_irqrestore(&node->els_ios_lock, flags);
 		return NULL;
 	}
 
@@ -74,7 +70,6 @@
 					      &els->io.req.phys, GFP_DMA);
 	if (!els->io.req.virt) {
 		mempool_free(els, efc->els_io_pool);
-		spin_unlock_irqrestore(&node->els_ios_lock, flags);
 		return NULL;
 	}
 
@@ -94,10 +89,11 @@
 
 		/* add els structure to ELS IO list */
 		INIT_LIST_HEAD(&els->list_entry);
+		spin_lock_irqsave(&node->els_ios_lock, flags);
 		list_add_tail(&els->list_entry, &node->els_ios_list);
+		spin_unlock_irqrestore(&node->els_ios_lock, flags);
 	}
 
-	spin_unlock_irqrestore(&node->els_ios_lock, flags);
 	return els;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/elx/libefc/efc_nport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/elx/libefc/efc_nport.c
@@ -705,9 +705,9 @@
 	spin_lock_irqsave(&efc->lock, flags);
 	list_for_each_entry(nport, &domain->nport_list, list_entry) {
 		if (nport->wwpn == wwpn && nport->wwnn == wwnn) {
-			kref_put(&nport->ref, nport->release);
 			/* Shutdown this NPORT */
 			efc_sm_post_event(&nport->sm, EFC_EVT_SHUTDOWN, NULL);
+			kref_put(&nport->ref, nport->release);
 			break;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/elx/libefc/efclib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/elx/libefc/efclib.h
@@ -58,10 +58,12 @@
 #define EFC_LINK_STATUS_UP		0
 #define EFC_LINK_STATUS_DOWN		1
 
+enum efc_sm_event;
+
 /* State machine context header  */
 struct efc_sm_ctx {
 	void (*current_state)(struct efc_sm_ctx *ctx,
-			      u32 evt, void *arg);
+			      enum efc_sm_event evt, void *arg);
 
 	const char	*description;
 	void		*app;
@@ -364,7 +366,7 @@
 	int			prev_evt;
 
 	void (*nodedb_state)(struct efc_sm_ctx *ctx,
-			     u32 evt, void *arg);
+			     enum efc_sm_event evt, void *arg);
 	struct timer_list	gidpt_delay_timer;
 	u64			time_last_gidpt_msec;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/fcoe/fcoe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/fcoe/fcoe.c
@@ -2501,6 +2501,7 @@
 
 out_free:
 	mutex_unlock(&fcoe_config_mutex);
+	fcoe_transport_detach(&fcoe_sw_transport);
 out_destroy:
 	destroy_workqueue(fcoe_wq);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/fcoe/fcoe_ctlr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/fcoe/fcoe_ctlr.c
@@ -1969,7 +1969,7 @@
  *
  * Returns: u64 fc world wide name
  */
-u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN],
+u64 fcoe_wwn_from_mac(unsigned char mac[ETH_ALEN],
 		      unsigned int scheme, unsigned int port)
 {
 	u64 wwn;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/fcoe/fcoe_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/fcoe/fcoe_sysfs.c
@@ -830,14 +830,15 @@
 
 	dev_set_name(&ctlr->dev, "ctlr_%d", ctlr->id);
 	error = device_register(&ctlr->dev);
-	if (error)
-		goto out_del_q2;
+	if (error) {
+		destroy_workqueue(ctlr->devloss_work_q);
+		destroy_workqueue(ctlr->work_q);
+		put_device(&ctlr->dev);
+		return NULL;
+	}
 
 	return ctlr;
 
-out_del_q2:
-	destroy_workqueue(ctlr->devloss_work_q);
-	ctlr->devloss_work_q = NULL;
 out_del_q:
 	destroy_workqueue(ctlr->work_q);
 	ctlr->work_q = NULL;
@@ -1036,16 +1037,16 @@
 	fcf->selected = new_fcf->selected;
 
 	error = device_register(&fcf->dev);
-	if (error)
-		goto out_del;
+	if (error) {
+		put_device(&fcf->dev);
+		goto out;
+	}
 
 	fcf->state = FCOE_FCF_STATE_CONNECTED;
 	list_add_tail(&fcf->peers, &ctlr->fcfs);
 
 	return fcf;
 
-out_del:
-	kfree(fcf);
 out:
 	return NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/fnic/fnic_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/fnic/fnic_debugfs.c
@@ -66,9 +66,10 @@
 		fc_trc_flag->fnic_trace = 2;
 		fc_trc_flag->fc_trace = 3;
 		fc_trc_flag->fc_clear = 4;
+		return 0;
 	}
 
-	return 0;
+	return -ENOMEM;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/fnic/fnic_scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/fnic/fnic_scsi.c
@@ -604,7 +604,7 @@
 
 	FNIC_TRACE(fnic_queuecommand, sc->device->host->host_no,
 		  tag, sc, io_req, sg_count, cmd_trace,
-		  (((u64)CMD_FLAGS(sc) >> 32) | CMD_STATE(sc)));
+		  (((u64)CMD_FLAGS(sc) << 32) | CMD_STATE(sc)));
 
 	/* if only we issued IO, will we have the io lock */
 	if (io_lock_acquired)
@@ -2172,7 +2172,7 @@
 				     bool new_sc)
 
 {
-	int ret = SUCCESS;
+	int ret = 0;
 	struct fnic_pending_aborts_iter_data iter_data = {
 		.fnic = fnic,
 		.lun_dev = lr_sc->device,
@@ -2192,9 +2192,11 @@
 
 	/* walk again to check, if IOs are still pending in fw */
 	if (fnic_is_abts_pending(fnic, lr_sc))
-		ret = FAILED;
+		ret = 1;
 
 clean_pending_aborts_end:
+	FNIC_SCSI_DBG(KERN_INFO, fnic->lport->host,
+			"%s: exit status: %d\n", __func__, ret);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/g_NCR5380.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/g_NCR5380.c
@@ -663,7 +663,7 @@
 static int generic_NCR5380_dma_xfer_len(struct NCR5380_hostdata *hostdata,
                                         struct scsi_cmnd *cmd)
 {
-	int transfersize = cmd->SCp.this_residual;
+	int transfersize = NCR5380_to_ncmd(cmd)->this_residual;
 
 	if (hostdata->flags & FLAG_NO_PSEUDO_DMA)
 		return 0;
@@ -675,7 +675,7 @@
 	/* Limit PDMA send to 512 B to avoid random corruption on DTC3181E */
 	if (hostdata->board == BOARD_DTC3181E &&
 	    cmd->sc_data_direction == DMA_TO_DEVICE)
-		transfersize = min(cmd->SCp.this_residual, 512);
+		transfersize = min(transfersize, 512);
 
 	return min(transfersize, DMA_MAX_SIZE);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hisi_sas/hisi_sas.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hisi_sas/hisi_sas.h
@@ -35,7 +35,7 @@
 #define HISI_SAS_QUEUE_SLOTS	4096
 #define HISI_SAS_MAX_ITCT_ENTRIES 1024
 #define HISI_SAS_MAX_DEVICES HISI_SAS_MAX_ITCT_ENTRIES
-#define HISI_SAS_RESET_BIT	0
+#define HISI_SAS_RESETTING_BIT	0
 #define HISI_SAS_REJECT_CMD_BIT	1
 #define HISI_SAS_PM_BIT		2
 #define HISI_SAS_HW_FAULT_BIT	3
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hisi_sas/hisi_sas_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hisi_sas/hisi_sas_main.c
@@ -724,7 +724,7 @@
 		 */
 		local_phy = sas_get_local_phy(device);
 		if (!scsi_is_sas_phy_local(local_phy) &&
-		    !test_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags)) {
+		    !test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags)) {
 			unsigned long deadline = ata_deadline(jiffies, 20000);
 			struct sata_device *sata_dev = &device->sata_dev;
 			struct ata_host *ata_host = sata_dev->ata_host;
@@ -1072,7 +1072,7 @@
 		 sas_dev->device_id, sas_dev->dev_type);
 
 	down(&hisi_hba->sem);
-	if (!test_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags)) {
+	if (!test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags)) {
 		hisi_sas_internal_task_abort(hisi_hba, device,
 					     HISI_SAS_INT_ABT_DEV, 0, true);
 
@@ -1414,7 +1414,7 @@
 				device->linkrate = phy->sas_phy.linkrate;
 
 			hisi_hba->hw->setup_itct(hisi_hba, sas_dev);
-		} else
+		} else if (!port->port_attached)
 			port->id = 0xff;
 	}
 }
@@ -1548,7 +1548,6 @@
 {
 	struct Scsi_Host *shost = hisi_hba->shost;
 
-	down(&hisi_hba->sem);
 	hisi_hba->phy_state = hisi_hba->hw->get_phys_state(hisi_hba);
 
 	scsi_block_requests(shost);
@@ -1574,9 +1573,9 @@
 	if (hisi_hba->reject_stp_links_msk)
 		hisi_sas_terminate_stp_reject(hisi_hba);
 	hisi_sas_reset_init_all_devices(hisi_hba);
-	up(&hisi_hba->sem);
 	scsi_unblock_requests(shost);
-	clear_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags);
+	clear_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags);
+	up(&hisi_hba->sem);
 
 	hisi_sas_rescan_topology(hisi_hba, hisi_hba->phy_state);
 }
@@ -1585,10 +1584,13 @@
 static int hisi_sas_controller_prereset(struct hisi_hba *hisi_hba)
 {
 	if (!hisi_hba->hw->soft_reset)
-		return -1;
+		return -ENOENT;
 
-	if (test_and_set_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags))
-		return -1;
+	down(&hisi_hba->sem);
+	if (test_and_set_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags)) {
+		up(&hisi_hba->sem);
+		return -EPERM;
+	}
 
 	if (hisi_sas_debugfs_enable && hisi_hba->debugfs_itct[0].itct)
 		hisi_hba->hw->debugfs_snapshot_regs(hisi_hba);
@@ -1611,7 +1613,7 @@
 		clear_bit(HISI_SAS_REJECT_CMD_BIT, &hisi_hba->flags);
 		up(&hisi_hba->sem);
 		scsi_unblock_requests(shost);
-		clear_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags);
+		clear_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags);
 		return rc;
 	}
 
@@ -2251,7 +2253,7 @@
 	} else {
 		struct hisi_sas_port *port  = phy->port;
 
-		if (test_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags) ||
+		if (test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags) ||
 		    phy->in_reset) {
 			dev_info(dev, "ignore flutter phy%d down\n", phy_no);
 			return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hisi_sas/hisi_sas_v1_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hisi_sas/hisi_sas_v1_hw.c
@@ -1422,7 +1422,7 @@
 		goto end;
 	}
 
-	if (!test_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags))
+	if (!test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags))
 		sas_notify_port_event(sas_phy, PORTE_BROADCAST_RCVD,
 				      GFP_ATOMIC);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
@@ -2026,6 +2026,11 @@
 	u16 dma_tx_err_type = le16_to_cpu(err_record->dma_tx_err_type);
 	u16 sipc_rx_err_type = le16_to_cpu(err_record->sipc_rx_err_type);
 	u32 dma_rx_err_type = le32_to_cpu(err_record->dma_rx_err_type);
+	struct hisi_sas_complete_v2_hdr *complete_queue =
+			hisi_hba->complete_hdr[slot->cmplt_queue];
+	struct hisi_sas_complete_v2_hdr *complete_hdr =
+			&complete_queue[slot->cmplt_queue_slot];
+	u32 dw0 = le32_to_cpu(complete_hdr->dw0);
 	int error = -1;
 
 	if (err_phase == 1) {
@@ -2310,7 +2315,8 @@
 			break;
 		}
 		}
-		hisi_sas_sata_done(task, slot);
+		if (dw0 & CMPLT_HDR_RSPNS_XFRD_MSK)
+			hisi_sas_sata_done(task, slot);
 	}
 		break;
 	default:
@@ -2442,7 +2448,8 @@
 	case SAS_PROTOCOL_SATA | SAS_PROTOCOL_STP:
 	{
 		ts->stat = SAS_SAM_STAT_GOOD;
-		hisi_sas_sata_done(task, slot);
+		if (dw0 & CMPLT_HDR_RSPNS_XFRD_MSK)
+			hisi_sas_sata_done(task, slot);
 		break;
 	}
 	default:
@@ -2824,7 +2831,7 @@
 	hisi_sas_phy_write32(hisi_hba, phy_no, SL_RX_BCAST_CHK_MSK, 1);
 	bcast_status = hisi_sas_phy_read32(hisi_hba, phy_no, RX_PRIMS_STATUS);
 	if ((bcast_status & RX_BCAST_CHG_MSK) &&
-	    !test_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags))
+	    !test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags))
 		sas_notify_port_event(sas_phy, PORTE_BROADCAST_RCVD,
 				      GFP_ATOMIC);
 	hisi_sas_phy_write32(hisi_hba, phy_no, CHL_INT0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
@@ -405,6 +405,8 @@
 #define CMPLT_HDR_ERROR_PHASE_MSK   (0xff << CMPLT_HDR_ERROR_PHASE_OFF)
 #define CMPLT_HDR_RSPNS_XFRD_OFF	10
 #define CMPLT_HDR_RSPNS_XFRD_MSK	(0x1 << CMPLT_HDR_RSPNS_XFRD_OFF)
+#define CMPLT_HDR_RSPNS_GOOD_OFF	11
+#define CMPLT_HDR_RSPNS_GOOD_MSK	(0x1 << CMPLT_HDR_RSPNS_GOOD_OFF)
 #define CMPLT_HDR_ERX_OFF		12
 #define CMPLT_HDR_ERX_MSK		(0x1 << CMPLT_HDR_ERX_OFF)
 #define CMPLT_HDR_ABORT_STAT_OFF	13
@@ -478,6 +480,9 @@
 #define RX_DATA_LEN_UNDERFLOW_OFF	6
 #define RX_DATA_LEN_UNDERFLOW_MSK	(1 << RX_DATA_LEN_UNDERFLOW_OFF)
 
+#define RX_FIS_STATUS_ERR_OFF		0
+#define RX_FIS_STATUS_ERR_MSK		(1 << RX_FIS_STATUS_ERR_OFF)
+
 #define HISI_SAS_COMMAND_ENTRIES_V3_HW 4096
 #define HISI_SAS_MSI_COUNT_V3_HW 32
 
@@ -518,6 +523,8 @@
 #define CHNL_INT_STS_INT2_MSK BIT(3)
 #define CHNL_WIDTH 4
 
+#define BAR_NO_V3_HW	5
+
 enum {
 	DSM_FUNC_ERR_HANDLE_MSI = 0,
 };
@@ -527,7 +534,7 @@
 
 /* permit overriding the host protection capabilities mask (EEDP/T10 PI) */
 static int prot_mask;
-module_param(prot_mask, int, 0);
+module_param(prot_mask, int, 0444);
 MODULE_PARM_DESC(prot_mask, " host protection capabilities mask, def=0x0 ");
 
 static void debugfs_work_handler_v3_hw(struct work_struct *work);
@@ -1615,7 +1622,7 @@
 	hisi_sas_phy_write32(hisi_hba, phy_no, SL_RX_BCAST_CHK_MSK, 1);
 	bcast_status = hisi_sas_phy_read32(hisi_hba, phy_no, RX_PRIMS_STATUS);
 	if ((bcast_status & RX_BCAST_CHG_MSK) &&
-	    !test_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags))
+	    !test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags))
 		sas_notify_port_event(sas_phy, PORTE_BROADCAST_RCVD,
 				      GFP_ATOMIC);
 	hisi_sas_phy_write32(hisi_hba, phy_no, CHL_INT0,
@@ -2134,7 +2141,7 @@
 	return IRQ_HANDLED;
 }
 
-static void
+static bool
 slot_err_v3_hw(struct hisi_hba *hisi_hba, struct sas_task *task,
 	       struct hisi_sas_slot *slot)
 {
@@ -2147,11 +2154,22 @@
 			hisi_sas_status_buf_addr_mem(slot);
 	u32 dma_rx_err_type = le32_to_cpu(record->dma_rx_err_type);
 	u32 trans_tx_fail_type = le32_to_cpu(record->trans_tx_fail_type);
+	u16 sipc_rx_err_type = le16_to_cpu(record->sipc_rx_err_type);
 	u32 dw3 = le32_to_cpu(complete_hdr->dw3);
+	u32 dw0 = le32_to_cpu(complete_hdr->dw0);
 
 	switch (task->task_proto) {
 	case SAS_PROTOCOL_SSP:
 		if (dma_rx_err_type & RX_DATA_LEN_UNDERFLOW_MSK) {
+			/*
+			 * If returned response frame is incorrect because of data underflow,
+			 * but I/O information has been written to the host memory, we examine
+			 * response IU.
+			 */
+			if (!(dw0 & CMPLT_HDR_RSPNS_GOOD_MSK) &&
+			    (dw0 & CMPLT_HDR_RSPNS_XFRD_MSK))
+				return false;
+
 			ts->residual = trans_tx_fail_type;
 			ts->stat = SAS_DATA_UNDERRUN;
 		} else if (dw3 & CMPLT_HDR_IO_IN_TARGET_MSK) {
@@ -2165,7 +2183,10 @@
 	case SAS_PROTOCOL_SATA:
 	case SAS_PROTOCOL_STP:
 	case SAS_PROTOCOL_SATA | SAS_PROTOCOL_STP:
-		if (dma_rx_err_type & RX_DATA_LEN_UNDERFLOW_MSK) {
+		if ((dw0 & CMPLT_HDR_RSPNS_XFRD_MSK) &&
+		    (sipc_rx_err_type & RX_FIS_STATUS_ERR_MSK)) {
+			ts->stat = SAS_PROTO_RESPONSE;
+		} else if (dma_rx_err_type & RX_DATA_LEN_UNDERFLOW_MSK) {
 			ts->residual = trans_tx_fail_type;
 			ts->stat = SAS_DATA_UNDERRUN;
 		} else if (dw3 & CMPLT_HDR_IO_IN_TARGET_MSK) {
@@ -2175,7 +2196,8 @@
 			ts->stat = SAS_OPEN_REJECT;
 			ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
 		}
-		hisi_sas_sata_done(task, slot);
+		if (dw0 & CMPLT_HDR_RSPNS_XFRD_MSK)
+			hisi_sas_sata_done(task, slot);
 		break;
 	case SAS_PROTOCOL_SMP:
 		ts->stat = SAS_SAM_STAT_CHECK_CONDITION;
@@ -2183,6 +2205,7 @@
 	default:
 		break;
 	}
+	return true;
 }
 
 static void slot_complete_v3_hw(struct hisi_hba *hisi_hba,
@@ -2257,19 +2280,20 @@
 	if ((dw0 & CMPLT_HDR_CMPLT_MSK) == 0x3) {
 		u32 *error_info = hisi_sas_status_buf_addr_mem(slot);
 
-		slot_err_v3_hw(hisi_hba, task, slot);
-		if (ts->stat != SAS_DATA_UNDERRUN)
-			dev_info(dev, "erroneous completion iptt=%d task=%pK dev id=%d addr=%016llx CQ hdr: 0x%x 0x%x 0x%x 0x%x Error info: 0x%x 0x%x 0x%x 0x%x\n",
-				 slot->idx, task, sas_dev->device_id,
-				 SAS_ADDR(device->sas_addr),
-				 dw0, dw1, complete_hdr->act, dw3,
-				 error_info[0], error_info[1],
-				 error_info[2], error_info[3]);
-		if (unlikely(slot->abort)) {
-			sas_task_abort(task);
-			return;
+		if (slot_err_v3_hw(hisi_hba, task, slot)) {
+			if (ts->stat != SAS_DATA_UNDERRUN)
+				dev_info(dev, "erroneous completion iptt=%d task=%pK dev id=%d addr=%016llx CQ hdr: 0x%x 0x%x 0x%x 0x%x Error info: 0x%x 0x%x 0x%x 0x%x\n",
+					slot->idx, task, sas_dev->device_id,
+					SAS_ADDR(device->sas_addr),
+					dw0, dw1, complete_hdr->act, dw3,
+					error_info[0], error_info[1],
+					error_info[2], error_info[3]);
+			if (unlikely(slot->abort)) {
+				sas_task_abort(task);
+				return;
+			}
+			goto out;
 		}
-		goto out;
 	}
 
 	switch (task->task_proto) {
@@ -2299,7 +2323,8 @@
 	case SAS_PROTOCOL_STP:
 	case SAS_PROTOCOL_SATA | SAS_PROTOCOL_STP:
 		ts->stat = SAS_SAM_STAT_GOOD;
-		hisi_sas_sata_done(task, slot);
+		if (dw0 & CMPLT_HDR_RSPNS_XFRD_MSK)
+			hisi_sas_sata_done(task, slot);
 		break;
 	default:
 		ts->stat = SAS_SAM_STAT_CHECK_CONDITION;
@@ -2377,6 +2402,7 @@
 	/* update rd_point */
 	cq->rd_point = rd_point;
 	hisi_sas_write32(hisi_hba, COMPL_Q_0_RD_PTR + (0x14 * queue), rd_point);
+	cond_resched();
 
 	return IRQ_HANDLED;
 }
@@ -2392,17 +2418,25 @@
 	return IRQ_WAKE_THREAD;
 }
 
+static void hisi_sas_v3_free_vectors(void *data)
+{
+	struct pci_dev *pdev = data;
+
+	pci_free_irq_vectors(pdev);
+}
+
 static int interrupt_preinit_v3_hw(struct hisi_hba *hisi_hba)
 {
 	int vectors;
 	int max_msi = HISI_SAS_MSI_COUNT_V3_HW, min_msi;
 	struct Scsi_Host *shost = hisi_hba->shost;
+	struct pci_dev *pdev = hisi_hba->pci_dev;
 	struct irq_affinity desc = {
 		.pre_vectors = BASE_VECTORS_V3_HW,
 	};
 
 	min_msi = MIN_AFFINE_VECTORS_V3_HW;
-	vectors = pci_alloc_irq_vectors_affinity(hisi_hba->pci_dev,
+	vectors = pci_alloc_irq_vectors_affinity(pdev,
 						 min_msi, max_msi,
 						 PCI_IRQ_MSI |
 						 PCI_IRQ_AFFINITY,
@@ -2414,7 +2448,7 @@
 	hisi_hba->cq_nvecs = vectors - BASE_VECTORS_V3_HW;
 	shost->nr_hw_queues = hisi_hba->cq_nvecs;
 
-	return 0;
+	return devm_add_action(&pdev->dev, hisi_sas_v3_free_vectors, pdev);
 }
 
 static int interrupt_init_v3_hw(struct hisi_hba *hisi_hba)
@@ -2749,6 +2783,7 @@
 	struct hisi_hba *hisi_hba = shost_priv(shost);
 	struct device *dev = hisi_hba->dev;
 	int ret = sas_slave_configure(sdev);
+	unsigned int max_sectors;
 
 	if (ret)
 		return ret;
@@ -2766,6 +2801,12 @@
 		}
 	}
 
+	/* Set according to IOMMU IOVA caching limit */
+	max_sectors = min_t(size_t, queue_max_hw_sectors(sdev->request_queue),
+			    (PAGE_SIZE * 32) >> SECTOR_SHIFT);
+
+	blk_queue_max_hw_sectors(sdev->request_queue, max_sectors);
+
 	return 0;
 }
 
@@ -3291,7 +3332,7 @@
 	u32 *databuf = hisi_hba->debugfs_regs[dump_index][DEBUGFS_GLOBAL].data;
 	int i;
 
-	for (i = 0; i < debugfs_axi_reg.count; i++, databuf++)
+	for (i = 0; i < debugfs_global_reg.count; i++, databuf++)
 		*databuf = hisi_sas_read32(hisi_hba, 4 * i);
 }
 
@@ -3686,7 +3727,6 @@
 
 	do_div(timestamp, NSEC_PER_MSEC);
 	hisi_hba->debugfs_timestamp[debugfs_dump_index] = timestamp;
-	hisi_hba->debugfs_dump_index++;
 
 	debugfs_snapshot_prepare_v3_hw(hisi_hba);
 
@@ -3702,6 +3742,7 @@
 	debugfs_create_files_v3_hw(hisi_hba);
 
 	debugfs_snapshot_restore_v3_hw(hisi_hba);
+	hisi_hba->debugfs_dump_index++;
 }
 
 static ssize_t debugfs_trigger_dump_v3_hw_write(struct file *file,
@@ -3959,6 +4000,54 @@
 	.owner = THIS_MODULE,
 };
 
+static ssize_t debugfs_bist_cnt_v3_hw_write(struct file *filp,
+					const char __user *buf,
+					size_t count, loff_t *ppos)
+{
+	struct seq_file *m = filp->private_data;
+	struct hisi_hba *hisi_hba = m->private;
+	unsigned int cnt;
+	int val;
+
+	if (hisi_hba->debugfs_bist_enable)
+		return -EPERM;
+
+	val = kstrtouint_from_user(buf, count, 0, &cnt);
+	if (val)
+		return val;
+
+	if (cnt)
+		return -EINVAL;
+
+	hisi_hba->debugfs_bist_cnt = 0;
+	return count;
+}
+
+static int debugfs_bist_cnt_v3_hw_show(struct seq_file *s, void *p)
+{
+	struct hisi_hba *hisi_hba = s->private;
+
+	seq_printf(s, "%u\n", hisi_hba->debugfs_bist_cnt);
+
+	return 0;
+}
+
+static int debugfs_bist_cnt_v3_hw_open(struct inode *inode,
+					  struct file *filp)
+{
+	return single_open(filp, debugfs_bist_cnt_v3_hw_show,
+			   inode->i_private);
+}
+
+static const struct file_operations debugfs_bist_cnt_v3_hw_ops = {
+	.open = debugfs_bist_cnt_v3_hw_open,
+	.read = seq_read,
+	.write = debugfs_bist_cnt_v3_hw_write,
+	.llseek = seq_lseek,
+	.release = single_release,
+	.owner = THIS_MODULE,
+};
+
 static const struct {
 	int		value;
 	char		*name;
@@ -4596,8 +4685,8 @@
 	debugfs_create_file("phy_id", 0600, hisi_hba->debugfs_bist_dentry,
 			    hisi_hba, &debugfs_bist_phy_v3_hw_fops);
 
-	debugfs_create_u32("cnt", 0600, hisi_hba->debugfs_bist_dentry,
-			   &hisi_hba->debugfs_bist_cnt);
+	debugfs_create_file("cnt", 0600, hisi_hba->debugfs_bist_dentry,
+			    hisi_hba, &debugfs_bist_cnt_v3_hw_ops);
 
 	debugfs_create_file("loopback_mode", 0600,
 			    hisi_hba->debugfs_bist_dentry,
@@ -4630,6 +4719,12 @@
 	hisi_hba->debugfs_bist_linkrate = SAS_LINK_RATE_1_5_GBPS;
 }
 
+static void debugfs_exit_v3_hw(struct hisi_hba *hisi_hba)
+{
+	debugfs_remove_recursive(hisi_hba->debugfs_dir);
+	hisi_hba->debugfs_dir = NULL;
+}
+
 static void debugfs_init_v3_hw(struct hisi_hba *hisi_hba)
 {
 	struct device *dev = hisi_hba->dev;
@@ -4653,18 +4748,13 @@
 
 	for (i = 0; i < hisi_sas_debugfs_dump_count; i++) {
 		if (debugfs_alloc_v3_hw(hisi_hba, i)) {
-			debugfs_remove_recursive(hisi_hba->debugfs_dir);
+			debugfs_exit_v3_hw(hisi_hba);
 			dev_dbg(dev, "failed to init debugfs!\n");
 			break;
 		}
 	}
 }
 
-static void debugfs_exit_v3_hw(struct hisi_hba *hisi_hba)
-{
-	debugfs_remove_recursive(hisi_hba->debugfs_dir);
-}
-
 static int
 hisi_sas_v3_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
@@ -4676,15 +4766,15 @@
 	struct sas_ha_struct *sha;
 	int rc, phy_nr, port_nr, i;
 
-	rc = pci_enable_device(pdev);
+	rc = pcim_enable_device(pdev);
 	if (rc)
 		goto err_out;
 
 	pci_set_master(pdev);
 
-	rc = pci_request_regions(pdev, DRV_NAME);
+	rc = pcim_iomap_regions(pdev, 1 << BAR_NO_V3_HW, DRV_NAME);
 	if (rc)
-		goto err_out_disable_device;
+		goto err_out;
 
 	rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
 	if (rc)
@@ -4692,20 +4782,20 @@
 	if (rc) {
 		dev_err(dev, "No usable DMA addressing method\n");
 		rc = -ENODEV;
-		goto err_out_regions;
+		goto err_out;
 	}
 
 	shost = hisi_sas_shost_alloc_pci(pdev);
 	if (!shost) {
 		rc = -ENOMEM;
-		goto err_out_regions;
+		goto err_out;
 	}
 
 	sha = SHOST_TO_SAS_HA(shost);
 	hisi_hba = shost_priv(shost);
 	dev_set_drvdata(dev, sha);
 
-	hisi_hba->regs = pcim_iomap(pdev, 5, 0);
+	hisi_hba->regs = pcim_iomap_table(pdev)[BAR_NO_V3_HW];
 	if (!hisi_hba->regs) {
 		dev_err(dev, "cannot map register\n");
 		rc = -ENOMEM;
@@ -4763,7 +4853,7 @@
 	dev_err(dev, "%d hw queues\n", shost->nr_hw_queues);
 	rc = scsi_add_host(shost, dev);
 	if (rc)
-		goto err_out_free_irq_vectors;
+		goto err_out_debugfs;
 
 	rc = sas_register_ha(sha);
 	if (rc)
@@ -4792,17 +4882,11 @@
 	sas_unregister_ha(sha);
 err_out_register_ha:
 	scsi_remove_host(shost);
-err_out_free_irq_vectors:
-	pci_free_irq_vectors(pdev);
 err_out_debugfs:
 	debugfs_exit_v3_hw(hisi_hba);
 err_out_ha:
 	hisi_sas_free(hisi_hba);
 	scsi_host_put(shost);
-err_out_regions:
-	pci_release_regions(pdev);
-err_out_disable_device:
-	pci_disable_device(pdev);
 err_out:
 	return rc;
 }
@@ -4821,7 +4905,6 @@
 
 		devm_free_irq(&pdev->dev, pci_irq_vector(pdev, nr), cq);
 	}
-	pci_free_irq_vectors(pdev);
 }
 
 static void hisi_sas_v3_remove(struct pci_dev *pdev)
@@ -4840,8 +4923,6 @@
 	sas_remove_host(sha->core.shost);
 
 	hisi_sas_v3_destroy_irqs(pdev, hisi_hba);
-	pci_release_regions(pdev);
-	pci_disable_device(pdev);
 	hisi_sas_free(hisi_hba);
 	debugfs_exit_v3_hw(hisi_hba);
 	scsi_host_put(shost);
@@ -4855,7 +4936,8 @@
 	int rc;
 
 	dev_info(dev, "FLR prepare\n");
-	set_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags);
+	down(&hisi_hba->sem);
+	set_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags);
 	hisi_sas_controller_reset_prepare(hisi_hba);
 
 	rc = disable_host_v3_hw(hisi_hba);
@@ -4867,6 +4949,7 @@
 {
 	struct sas_ha_struct *sha = pci_get_drvdata(pdev);
 	struct hisi_hba *hisi_hba = sha->lldd_ha;
+	struct Scsi_Host *shost = hisi_hba->shost;
 	struct device *dev = hisi_hba->dev;
 	int rc;
 
@@ -4875,6 +4958,10 @@
 	rc = hw_init_v3_hw(hisi_hba);
 	if (rc) {
 		dev_err(dev, "FLR: hw init failed rc=%d\n", rc);
+		clear_bit(HISI_SAS_REJECT_CMD_BIT, &hisi_hba->flags);
+		scsi_unblock_requests(shost);
+		clear_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags);
+		up(&hisi_hba->sem);
 		return;
 	}
 
@@ -4901,8 +4988,8 @@
 		return -ENODEV;
 	}
 
-	if (test_and_set_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags))
-		return -1;
+	if (test_and_set_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags))
+		return -EPERM;
 
 	scsi_block_requests(shost);
 	set_bit(HISI_SAS_REJECT_CMD_BIT, &hisi_hba->flags);
@@ -4912,7 +4999,7 @@
 	if (rc) {
 		dev_err(dev, "PM suspend: disable host failed rc=%d\n", rc);
 		clear_bit(HISI_SAS_REJECT_CMD_BIT, &hisi_hba->flags);
-		clear_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags);
+		clear_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags);
 		scsi_unblock_requests(shost);
 		return rc;
 	}
@@ -4951,7 +5038,7 @@
 	}
 	phys_init_v3_hw(hisi_hba);
 	sas_resume_ha(sha);
-	clear_bit(HISI_SAS_RESET_BIT, &hisi_hba->flags);
+	clear_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hosts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hosts.c
@@ -180,6 +180,16 @@
 	scsi_forget_host(shost);
 	mutex_unlock(&shost->scan_mutex);
 	scsi_proc_host_rm(shost);
+	scsi_proc_hostdir_rm(shost->hostt);
+
+	/*
+	 * New SCSI devices cannot be attached anymore because of the SCSI host
+	 * state so drop the tag set refcnt. Wait until the tag set refcnt drops
+	 * to zero because .exit_cmd_priv implementations may need the host
+	 * pointer.
+	 */
+	kref_put(&shost->tagset_refcnt, scsi_mq_free_tags);
+	wait_for_completion(&shost->tagset_freed);
 
 	spin_lock_irqsave(shost->host_lock, flags);
 	if (scsi_host_set_state(shost, SHOST_DEL))
@@ -239,6 +249,9 @@
 
 	shost->dma_dev = dma_dev;
 
+	kref_init(&shost->tagset_refcnt);
+	init_completion(&shost->tagset_freed);
+
 	/*
 	 * Increase usage count temporarily here so that calling
 	 * scsi_autopm_put_host() will trigger runtime idle if there is
@@ -311,6 +324,7 @@
 	pm_runtime_disable(&shost->shost_gendev);
 	pm_runtime_set_suspended(&shost->shost_gendev);
 	pm_runtime_put_noidle(&shost->shost_gendev);
+	kref_put(&shost->tagset_refcnt, scsi_mq_free_tags);
  fail:
 	return error;
 }
@@ -321,8 +335,6 @@
 	struct Scsi_Host *shost = dev_to_shost(dev);
 	struct device *parent = dev->parent;
 
-	scsi_proc_hostdir_rm(shost->hostt);
-
 	/* Wait for functions invoked through call_rcu(&scmd->rcu, ...) */
 	rcu_barrier();
 
@@ -335,18 +347,16 @@
 
 	if (shost->shost_state == SHOST_CREATED) {
 		/*
-		 * Free the shost_dev device name here if scsi_host_alloc()
-		 * and scsi_host_put() have been called but neither
+		 * Free the shost_dev device name and remove the proc host dir
+		 * here if scsi_host_{alloc,put}() have been called but neither
 		 * scsi_host_add() nor scsi_host_remove() has been called.
 		 * This avoids that the memory allocated for the shost_dev
-		 * name is leaked.
+		 * name as well as the proc dir structure are leaked.
 		 */
+		scsi_proc_hostdir_rm(shost->hostt);
 		kfree(dev_name(&shost->shost_dev));
 	}
 
-	if (shost->tag_set.tags)
-		scsi_mq_destroy_tags(shost);
-
 	kfree(shost->shost_data);
 
 	ida_simple_remove(&host_index_ida, shost->host_no);
@@ -388,6 +398,7 @@
 	shost->shost_state = SHOST_CREATED;
 	INIT_LIST_HEAD(&shost->__devices);
 	INIT_LIST_HEAD(&shost->__targets);
+	INIT_LIST_HEAD(&shost->eh_abort_list);
 	INIT_LIST_HEAD(&shost->eh_cmd_q);
 	INIT_LIST_HEAD(&shost->starved_list);
 	init_waitqueue_head(&shost->host_wait);
@@ -518,7 +529,7 @@
 static int __scsi_host_match(struct device *dev, const void *data)
 {
 	struct Scsi_Host *p;
-	const unsigned short *hostnum = data;
+	const unsigned int *hostnum = data;
 
 	p = class_to_shost(dev);
 	return p->host_no == *hostnum;
@@ -535,7 +546,7 @@
  *	that scsi_host_get() took. The put_device() below dropped
  *	the reference from class_find_device().
  **/
-struct Scsi_Host *scsi_host_lookup(unsigned short hostnum)
+struct Scsi_Host *scsi_host_lookup(unsigned int hostnum)
 {
 	struct device *cdev;
 	struct Scsi_Host *shost = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/hpsa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/hpsa.c
@@ -5848,7 +5848,7 @@
 {
 	struct Scsi_Host *sh;
 
-	sh = scsi_host_alloc(&hpsa_driver_template, sizeof(h));
+	sh = scsi_host_alloc(&hpsa_driver_template, sizeof(struct ctlr_info *));
 	if (sh == NULL) {
 		dev_err(&h->pdev->dev, "scsi_host_alloc failed\n");
 		return -ENOMEM;
@@ -8927,7 +8927,7 @@
 		destroy_workqueue(h->monitor_ctlr_wq);
 		h->monitor_ctlr_wq = NULL;
 	}
-	kfree(h);
+	hpda_free_ctlr_info(h);
 	return rc;
 }
 
@@ -9788,7 +9788,8 @@
 	return 0;
 
 free_sas_phy:
-	hpsa_free_sas_phy(hpsa_sas_phy);
+	sas_phy_free(hpsa_sas_phy->phy);
+	kfree(hpsa_sas_phy);
 free_sas_port:
 	hpsa_free_sas_port(hpsa_sas_port);
 free_sas_node:
@@ -9824,10 +9825,12 @@
 
 	rc = hpsa_sas_port_add_rphy(hpsa_sas_port, rphy);
 	if (rc)
-		goto free_sas_port;
+		goto free_sas_rphy;
 
 	return 0;
 
+free_sas_rphy:
+	sas_rphy_free(rphy);
 free_sas_port:
 	hpsa_free_sas_port(hpsa_sas_port);
 	device->sas_port = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ibmvscsi/ibmvfc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ibmvscsi/ibmvfc.c
@@ -22,7 +22,6 @@
 #include <linux/bsg-lib.h>
 #include <asm/firmware.h>
 #include <asm/irq.h>
-#include <asm/rtas.h>
 #include <asm/vio.h>
 #include <scsi/scsi.h>
 #include <scsi/scsi_cmnd.h>
@@ -160,8 +159,8 @@
 static void ibmvfc_tgt_implicit_logout_and_del(struct ibmvfc_target *);
 static void ibmvfc_tgt_move_login(struct ibmvfc_target *);
 
-static void ibmvfc_release_sub_crqs(struct ibmvfc_host *);
-static void ibmvfc_init_sub_crqs(struct ibmvfc_host *);
+static void ibmvfc_dereg_sub_crqs(struct ibmvfc_host *);
+static void ibmvfc_reg_sub_crqs(struct ibmvfc_host *);
 
 static const char *unknown_error = "unknown error";
 
@@ -708,8 +707,13 @@
 		memset(vhost->async_crq.msgs.async, 0, PAGE_SIZE);
 		vhost->async_crq.cur = 0;
 
-		list_for_each_entry(tgt, &vhost->targets, queue)
-			ibmvfc_del_tgt(tgt);
+		list_for_each_entry(tgt, &vhost->targets, queue) {
+			if (vhost->client_migrated)
+				tgt->need_login = 1;
+			else
+				ibmvfc_del_tgt(tgt);
+		}
+
 		scsi_block_requests(vhost->host);
 		ibmvfc_set_host_action(vhost, IBMVFC_HOST_ACTION_INIT);
 		vhost->job_step = ibmvfc_npiv_login;
@@ -917,7 +921,7 @@
 	struct vio_dev *vdev = to_vio_dev(vhost->dev);
 	unsigned long flags;
 
-	ibmvfc_release_sub_crqs(vhost);
+	ibmvfc_dereg_sub_crqs(vhost);
 
 	/* Re-enable the CRQ */
 	do {
@@ -936,7 +940,7 @@
 	spin_unlock(vhost->crq.q_lock);
 	spin_unlock_irqrestore(vhost->host->host_lock, flags);
 
-	ibmvfc_init_sub_crqs(vhost);
+	ibmvfc_reg_sub_crqs(vhost);
 
 	return rc;
 }
@@ -955,7 +959,7 @@
 	struct vio_dev *vdev = to_vio_dev(vhost->dev);
 	struct ibmvfc_queue *crq = &vhost->crq;
 
-	ibmvfc_release_sub_crqs(vhost);
+	ibmvfc_dereg_sub_crqs(vhost);
 
 	/* Close the CRQ */
 	do {
@@ -988,7 +992,7 @@
 	spin_unlock(vhost->crq.q_lock);
 	spin_unlock_irqrestore(vhost->host->host_lock, flags);
 
-	ibmvfc_init_sub_crqs(vhost);
+	ibmvfc_reg_sub_crqs(vhost);
 
 	return rc;
 }
@@ -1514,7 +1518,11 @@
 	unsigned long flags;
 
 	spin_lock_irqsave(&queue->l_lock, flags);
-	BUG_ON(list_empty(&queue->free));
+	if (list_empty(&queue->free)) {
+		ibmvfc_log(queue->vhost, 4, "empty event pool on queue:%ld\n", queue->hwq_id);
+		spin_unlock_irqrestore(&queue->l_lock, flags);
+		return NULL;
+	}
 	evt = list_entry(queue->free.next, struct ibmvfc_event, queue_list);
 	atomic_set(&evt->free, 0);
 	list_del(&evt->queue_list);
@@ -1943,9 +1951,15 @@
 	if (vhost->using_channels) {
 		scsi_channel = hwq % vhost->scsi_scrqs.active_queues;
 		evt = ibmvfc_get_event(&vhost->scsi_scrqs.scrqs[scsi_channel]);
+		if (!evt)
+			return SCSI_MLQUEUE_HOST_BUSY;
+
 		evt->hwq = hwq % vhost->scsi_scrqs.active_queues;
-	} else
+	} else {
 		evt = ibmvfc_get_event(&vhost->crq);
+		if (!evt)
+			return SCSI_MLQUEUE_HOST_BUSY;
+	}
 
 	ibmvfc_init_event(evt, ibmvfc_scsi_done, IBMVFC_CMD_FORMAT);
 	evt->cmnd = cmnd;
@@ -2033,6 +2047,11 @@
 
 	vhost->aborting_passthru = 1;
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		spin_unlock_irqrestore(vhost->host->host_lock, flags);
+		return -ENOMEM;
+	}
+
 	ibmvfc_init_event(evt, ibmvfc_bsg_timeout_done, IBMVFC_MAD_FORMAT);
 
 	tmf = &evt->iu.tmf;
@@ -2091,6 +2110,10 @@
 		goto unlock_out;
 
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		rc = -ENOMEM;
+		goto unlock_out;
+	}
 	ibmvfc_init_event(evt, ibmvfc_sync_completion, IBMVFC_MAD_FORMAT);
 	plogi = &evt->iu.plogi;
 	memset(plogi, 0, sizeof(*plogi));
@@ -2209,6 +2232,11 @@
 	}
 
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		spin_unlock_irqrestore(vhost->host->host_lock, flags);
+		rc = -ENOMEM;
+		goto out;
+	}
 	ibmvfc_init_event(evt, ibmvfc_sync_completion, IBMVFC_MAD_FORMAT);
 	mad = &evt->iu.passthru;
 
@@ -2297,6 +2325,11 @@
 		else
 			evt = ibmvfc_get_event(&vhost->crq);
 
+		if (!evt) {
+			spin_unlock_irqrestore(vhost->host->host_lock, flags);
+			return -ENOMEM;
+		}
+
 		ibmvfc_init_event(evt, ibmvfc_sync_completion, IBMVFC_CMD_FORMAT);
 		tmf = ibmvfc_init_vfc_cmd(evt, sdev);
 		iu = ibmvfc_get_fcp_iu(vhost, tmf);
@@ -2500,6 +2533,8 @@
 	struct ibmvfc_tmf *tmf;
 
 	evt = ibmvfc_get_event(queue);
+	if (!evt)
+		return NULL;
 	ibmvfc_init_event(evt, ibmvfc_sync_completion, IBMVFC_MAD_FORMAT);
 
 	tmf = &evt->iu.tmf;
@@ -2556,6 +2591,11 @@
 
 		if (found_evt && vhost->logged_in) {
 			evt = ibmvfc_init_tmf(&queues[i], sdev, type);
+			if (!evt) {
+				spin_unlock(queues[i].q_lock);
+				spin_unlock_irqrestore(vhost->host->host_lock, flags);
+				return -ENOMEM;
+			}
 			evt->sync_iu = &queues[i].cancel_rsp;
 			ibmvfc_send_event(evt, vhost, default_timeout);
 			list_add_tail(&evt->cancel, &cancelq);
@@ -2769,6 +2809,10 @@
 
 	if (vhost->state == IBMVFC_ACTIVE) {
 		evt = ibmvfc_get_event(&vhost->crq);
+		if (!evt) {
+			spin_unlock_irqrestore(vhost->host->host_lock, flags);
+			return -ENOMEM;
+		}
 		ibmvfc_init_event(evt, ibmvfc_sync_completion, IBMVFC_CMD_FORMAT);
 		tmf = ibmvfc_init_vfc_cmd(evt, sdev);
 		iu = ibmvfc_get_fcp_iu(vhost, tmf);
@@ -3235,9 +3279,12 @@
 			/* We need to re-setup the interpartition connection */
 			dev_info(vhost->dev, "Partition migrated, Re-enabling adapter\n");
 			vhost->client_migrated = 1;
+
+			scsi_block_requests(vhost->host);
 			ibmvfc_purge_requests(vhost, DID_REQUEUE);
-			ibmvfc_link_down(vhost, IBMVFC_LINK_DOWN);
+			ibmvfc_set_host_state(vhost, IBMVFC_LINK_DOWN);
 			ibmvfc_set_host_action(vhost, IBMVFC_HOST_ACTION_REENABLE);
+			wake_up(&vhost->work_wait_q);
 		} else if (crq->format == IBMVFC_PARTNER_FAILED || crq->format == IBMVFC_PARTNER_DEREGISTER) {
 			dev_err(vhost->dev, "Host partner adapter deregistered or failed (rc=%d)\n", crq->format);
 			ibmvfc_purge_requests(vhost, DID_ERROR);
@@ -4022,6 +4069,12 @@
 
 	kref_get(&tgt->kref);
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_NONE);
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		return;
+	}
 	vhost->discovery_threads++;
 	ibmvfc_init_event(evt, ibmvfc_tgt_prli_done, IBMVFC_MAD_FORMAT);
 	evt->tgt = tgt;
@@ -4129,6 +4182,12 @@
 	kref_get(&tgt->kref);
 	tgt->logo_rcvd = 0;
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_NONE);
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		return;
+	}
 	vhost->discovery_threads++;
 	ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_INIT_WAIT);
 	ibmvfc_init_event(evt, ibmvfc_tgt_plogi_done, IBMVFC_MAD_FORMAT);
@@ -4205,6 +4264,8 @@
 
 	kref_get(&tgt->kref);
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt)
+		return NULL;
 	ibmvfc_init_event(evt, done, IBMVFC_MAD_FORMAT);
 	evt->tgt = tgt;
 	mad = &evt->iu.implicit_logout;
@@ -4232,6 +4293,13 @@
 	vhost->discovery_threads++;
 	evt = __ibmvfc_tgt_get_implicit_logout_evt(tgt,
 						   ibmvfc_tgt_implicit_logout_done);
+	if (!evt) {
+		vhost->discovery_threads--;
+		ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_NONE);
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		return;
+	}
 
 	ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_INIT_WAIT);
 	if (ibmvfc_send_event(evt, vhost, default_timeout)) {
@@ -4371,6 +4439,12 @@
 
 	kref_get(&tgt->kref);
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_DEL_RPORT);
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		return;
+	}
 	vhost->discovery_threads++;
 	ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_INIT_WAIT);
 	ibmvfc_init_event(evt, ibmvfc_tgt_move_login_done, IBMVFC_MAD_FORMAT);
@@ -4537,6 +4611,14 @@
 	vhost->abort_threads++;
 	kref_get(&tgt->kref);
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		tgt_err(tgt, "Failed to get cancel event for ADISC.\n");
+		vhost->abort_threads--;
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		spin_unlock_irqrestore(vhost->host->host_lock, flags);
+		return;
+	}
 	ibmvfc_init_event(evt, ibmvfc_tgt_adisc_cancel_done, IBMVFC_MAD_FORMAT);
 
 	evt->tgt = tgt;
@@ -4587,6 +4669,12 @@
 
 	kref_get(&tgt->kref);
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_NONE);
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		return;
+	}
 	vhost->discovery_threads++;
 	ibmvfc_init_event(evt, ibmvfc_tgt_adisc_done, IBMVFC_MAD_FORMAT);
 	evt->tgt = tgt;
@@ -4690,6 +4778,12 @@
 
 	kref_get(&tgt->kref);
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		ibmvfc_set_tgt_action(tgt, IBMVFC_TGT_ACTION_NONE);
+		kref_put(&tgt->kref, ibmvfc_release_tgt);
+		__ibmvfc_reset_host(vhost);
+		return;
+	}
 	vhost->discovery_threads++;
 	evt->tgt = tgt;
 	ibmvfc_init_event(evt, ibmvfc_tgt_query_target_done, IBMVFC_MAD_FORMAT);
@@ -4862,6 +4956,13 @@
 {
 	struct ibmvfc_discover_targets *mad;
 	struct ibmvfc_event *evt = ibmvfc_get_event(&vhost->crq);
+	int level = IBMVFC_DEFAULT_LOG_LEVEL;
+
+	if (!evt) {
+		ibmvfc_log(vhost, level, "Discover Targets failed: no available events\n");
+		ibmvfc_hard_reset_host(vhost);
+		return;
+	}
 
 	ibmvfc_init_event(evt, ibmvfc_discover_targets_done, IBMVFC_MAD_FORMAT);
 	mad = &evt->iu.discover_targets;
@@ -4939,8 +5040,15 @@
 	struct ibmvfc_scsi_channels *scrqs = &vhost->scsi_scrqs;
 	unsigned int num_channels =
 		min(vhost->client_scsi_channels, vhost->max_vios_scsi_channels);
+	int level = IBMVFC_DEFAULT_LOG_LEVEL;
 	int i;
 
+	if (!evt) {
+		ibmvfc_log(vhost, level, "Channel Setup failed: no available events\n");
+		ibmvfc_hard_reset_host(vhost);
+		return;
+	}
+
 	memset(setup_buf, 0, sizeof(*setup_buf));
 	if (num_channels == 0)
 		setup_buf->flags = cpu_to_be32(IBMVFC_CANCEL_CHANNELS);
@@ -5002,6 +5110,13 @@
 {
 	struct ibmvfc_channel_enquiry *mad;
 	struct ibmvfc_event *evt = ibmvfc_get_event(&vhost->crq);
+	int level = IBMVFC_DEFAULT_LOG_LEVEL;
+
+	if (!evt) {
+		ibmvfc_log(vhost, level, "Channel Enquiry failed: no available events\n");
+		ibmvfc_hard_reset_host(vhost);
+		return;
+	}
 
 	ibmvfc_init_event(evt, ibmvfc_channel_enquiry_done, IBMVFC_MAD_FORMAT);
 	mad = &evt->iu.channel_enquiry;
@@ -5124,6 +5239,12 @@
 	struct ibmvfc_npiv_login_mad *mad;
 	struct ibmvfc_event *evt = ibmvfc_get_event(&vhost->crq);
 
+	if (!evt) {
+		ibmvfc_dbg(vhost, "NPIV Login failed: no available events\n");
+		ibmvfc_hard_reset_host(vhost);
+		return;
+	}
+
 	ibmvfc_gather_partition_info(vhost);
 	ibmvfc_set_login_info(vhost);
 	ibmvfc_init_event(evt, ibmvfc_npiv_login_done, IBMVFC_MAD_FORMAT);
@@ -5188,6 +5309,12 @@
 	struct ibmvfc_event *evt;
 
 	evt = ibmvfc_get_event(&vhost->crq);
+	if (!evt) {
+		ibmvfc_dbg(vhost, "NPIV Logout failed: no available events\n");
+		ibmvfc_hard_reset_host(vhost);
+		return;
+	}
+
 	ibmvfc_init_event(evt, ibmvfc_npiv_logout_done, IBMVFC_MAD_FORMAT);
 
 	mad = &evt->iu.npiv_logout;
@@ -5680,6 +5807,8 @@
 	queue->cur = 0;
 	queue->fmt = fmt;
 	queue->size = PAGE_SIZE / fmt_size;
+
+	queue->vhost = vhost;
 	return 0;
 }
 
@@ -5755,9 +5884,6 @@
 
 	ENTER;
 
-	if (ibmvfc_alloc_queue(vhost, scrq, IBMVFC_SUB_CRQ_FMT))
-		return -ENOMEM;
-
 	rc = h_reg_sub_crq(vdev->unit_address, scrq->msg_token, PAGE_SIZE,
 			   &scrq->cookie, &scrq->hw_irq);
 
@@ -5788,7 +5914,6 @@
 	}
 
 	scrq->hwq_id = index;
-	scrq->vhost = vhost;
 
 	LEAVE;
 	return 0;
@@ -5796,9 +5921,8 @@
 irq_failed:
 	do {
 		rc = plpar_hcall_norets(H_FREE_SUB_CRQ, vdev->unit_address, scrq->cookie);
-	} while (rtas_busy_delay(rc));
+	} while (rc == H_BUSY || H_IS_LONG_BUSY(rc));
 reg_failed:
-	ibmvfc_free_queue(vhost, scrq);
 	LEAVE;
 	return rc;
 }
@@ -5824,12 +5948,50 @@
 	if (rc)
 		dev_err(dev, "Failed to free sub-crq[%d]: rc=%ld\n", index, rc);
 
-	ibmvfc_free_queue(vhost, scrq);
+	/* Clean out the queue */
+	memset(scrq->msgs.crq, 0, PAGE_SIZE);
+	scrq->cur = 0;
+
+	LEAVE;
+}
+
+static void ibmvfc_reg_sub_crqs(struct ibmvfc_host *vhost)
+{
+	int i, j;
+
+	ENTER;
+	if (!vhost->mq_enabled || !vhost->scsi_scrqs.scrqs)
+		return;
+
+	for (i = 0; i < nr_scsi_hw_queues; i++) {
+		if (ibmvfc_register_scsi_channel(vhost, i)) {
+			for (j = i; j > 0; j--)
+				ibmvfc_deregister_scsi_channel(vhost, j - 1);
+			vhost->do_enquiry = 0;
+			return;
+		}
+	}
+
+	LEAVE;
+}
+
+static void ibmvfc_dereg_sub_crqs(struct ibmvfc_host *vhost)
+{
+	int i;
+
+	ENTER;
+	if (!vhost->mq_enabled || !vhost->scsi_scrqs.scrqs)
+		return;
+
+	for (i = 0; i < nr_scsi_hw_queues; i++)
+		ibmvfc_deregister_scsi_channel(vhost, i);
+
 	LEAVE;
 }
 
 static void ibmvfc_init_sub_crqs(struct ibmvfc_host *vhost)
 {
+	struct ibmvfc_queue *scrq;
 	int i, j;
 
 	ENTER;
@@ -5845,30 +6007,41 @@
 	}
 
 	for (i = 0; i < nr_scsi_hw_queues; i++) {
-		if (ibmvfc_register_scsi_channel(vhost, i)) {
-			for (j = i; j > 0; j--)
-				ibmvfc_deregister_scsi_channel(vhost, j - 1);
+		scrq = &vhost->scsi_scrqs.scrqs[i];
+		if (ibmvfc_alloc_queue(vhost, scrq, IBMVFC_SUB_CRQ_FMT)) {
+			for (j = i; j > 0; j--) {
+				scrq = &vhost->scsi_scrqs.scrqs[j - 1];
+				ibmvfc_free_queue(vhost, scrq);
+			}
 			kfree(vhost->scsi_scrqs.scrqs);
 			vhost->scsi_scrqs.scrqs = NULL;
 			vhost->scsi_scrqs.active_queues = 0;
 			vhost->do_enquiry = 0;
-			break;
+			vhost->mq_enabled = 0;
+			return;
 		}
 	}
 
+	ibmvfc_reg_sub_crqs(vhost);
+
 	LEAVE;
 }
 
 static void ibmvfc_release_sub_crqs(struct ibmvfc_host *vhost)
 {
+	struct ibmvfc_queue *scrq;
 	int i;
 
 	ENTER;
 	if (!vhost->scsi_scrqs.scrqs)
 		return;
 
-	for (i = 0; i < nr_scsi_hw_queues; i++)
-		ibmvfc_deregister_scsi_channel(vhost, i);
+	ibmvfc_dereg_sub_crqs(vhost);
+
+	for (i = 0; i < nr_scsi_hw_queues; i++) {
+		scrq = &vhost->scsi_scrqs.scrqs[i];
+		ibmvfc_free_queue(vhost, scrq);
+	}
 
 	kfree(vhost->scsi_scrqs.scrqs);
 	vhost->scsi_scrqs.scrqs = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ibmvscsi/ibmvfc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ibmvscsi/ibmvfc.h
@@ -789,6 +789,7 @@
 	spinlock_t _lock;
 	spinlock_t *q_lock;
 
+	struct ibmvfc_host *vhost;
 	struct ibmvfc_event_pool evt_pool;
 	struct list_head sent;
 	struct list_head free;
@@ -797,7 +798,6 @@
 	union ibmvfc_iu cancel_rsp;
 
 	/* Sub-CRQ fields */
-	struct ibmvfc_host *vhost;
 	unsigned long cookie;
 	unsigned long vios_cookie;
 	unsigned long hw_irq;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c
@@ -36,7 +36,7 @@
 
 #define IBMVSCSIS_VERSION	"v0.2"
 
-#define	INITIAL_SRP_LIMIT	800
+#define	INITIAL_SRP_LIMIT	1024
 #define	DEFAULT_MAX_SECTORS	256
 #define MAX_TXU			1024 * 1024
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ipr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ipr.c
@@ -1516,23 +1516,22 @@
 }
 
 /**
- * strip_and_pad_whitespace - Strip and pad trailing whitespace.
- * @i:		index into buffer
- * @buf:		string to modify
+ * strip_whitespace - Strip and pad trailing whitespace.
+ * @i:		size of buffer
+ * @buf:	string to modify
  *
- * This function will strip all trailing whitespace, pad the end
- * of the string with a single space, and NULL terminate the string.
+ * This function will strip all trailing whitespace and
+ * NUL terminate the string.
  *
- * Return value:
- * 	new length of string
  **/
-static int strip_and_pad_whitespace(int i, char *buf)
+static void strip_whitespace(int i, char *buf)
 {
+	if (i < 1)
+		return;
+	i--;
 	while (i && buf[i] == ' ')
 		i--;
-	buf[i+1] = ' ';
-	buf[i+2] = '\0';
-	return i + 2;
+	buf[i+1] = '\0';
 }
 
 /**
@@ -1547,19 +1546,21 @@
 static void ipr_log_vpd_compact(char *prefix, struct ipr_hostrcb *hostrcb,
 				struct ipr_vpd *vpd)
 {
-	char buffer[IPR_VENDOR_ID_LEN + IPR_PROD_ID_LEN + IPR_SERIAL_NUM_LEN + 3];
-	int i = 0;
+	char vendor_id[IPR_VENDOR_ID_LEN + 1];
+	char product_id[IPR_PROD_ID_LEN + 1];
+	char sn[IPR_SERIAL_NUM_LEN + 1];
 
-	memcpy(buffer, vpd->vpids.vendor_id, IPR_VENDOR_ID_LEN);
-	i = strip_and_pad_whitespace(IPR_VENDOR_ID_LEN - 1, buffer);
+	memcpy(vendor_id, vpd->vpids.vendor_id, IPR_VENDOR_ID_LEN);
+	strip_whitespace(IPR_VENDOR_ID_LEN, vendor_id);
 
-	memcpy(&buffer[i], vpd->vpids.product_id, IPR_PROD_ID_LEN);
-	i = strip_and_pad_whitespace(i + IPR_PROD_ID_LEN - 1, buffer);
+	memcpy(product_id, vpd->vpids.product_id, IPR_PROD_ID_LEN);
+	strip_whitespace(IPR_PROD_ID_LEN, product_id);
 
-	memcpy(&buffer[i], vpd->sn, IPR_SERIAL_NUM_LEN);
-	buffer[IPR_SERIAL_NUM_LEN + i] = '\0';
+	memcpy(sn, vpd->sn, IPR_SERIAL_NUM_LEN);
+	strip_whitespace(IPR_SERIAL_NUM_LEN, sn);
 
-	ipr_hcam_err(hostrcb, "%s VPID/SN: %s\n", prefix, buffer);
+	ipr_hcam_err(hostrcb, "%s VPID/SN: %s %s %s\n", prefix,
+		     vendor_id, product_id, sn);
 }
 
 /**
@@ -9791,7 +9792,7 @@
 					GFP_KERNEL);
 
 		if (!ioa_cfg->hrrq[i].host_rrq)  {
-			while (--i > 0)
+			while (--i >= 0)
 				dma_free_coherent(&pdev->dev,
 					sizeof(u32) * ioa_cfg->hrrq[i].size,
 					ioa_cfg->hrrq[i].host_rrq,
@@ -10064,7 +10065,7 @@
 			ioa_cfg->vectors_info[i].desc,
 			&ioa_cfg->hrrq[i]);
 		if (rc) {
-			while (--i >= 0)
+			while (--i > 0)
 				free_irq(pci_irq_vector(pdev, i),
 					&ioa_cfg->hrrq[i]);
 			return rc;
@@ -10869,11 +10870,19 @@
  **/
 static int __init ipr_init(void)
 {
+	int rc;
+
 	ipr_info("IBM Power RAID SCSI Device Driver version: %s %s\n",
 		 IPR_DRIVER_VERSION, IPR_DRIVER_DATE);
 
 	register_reboot_notifier(&ipr_notifier);
-	return pci_register_driver(&ipr_driver);
+	rc = pci_register_driver(&ipr_driver);
+	if (rc) {
+		unregister_reboot_notifier(&ipr_notifier);
+		return rc;
+	}
+
+	return 0;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/isci/request.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/isci/request.c
@@ -3390,7 +3390,7 @@
 		return SCI_FAILURE;
 	}
 
-	return SCI_SUCCESS;
+	return status;
 }
 
 static struct isci_request *isci_request_from_tag(struct isci_host *ihost, u16 tag)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/iscsi_tcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/iscsi_tcp.c
@@ -52,6 +52,10 @@
 static unsigned int iscsi_max_lun = ~0;
 module_param_named(max_lun, iscsi_max_lun, uint, S_IRUGO);
 
+static bool iscsi_recv_from_iscsi_q;
+module_param_named(recv_from_iscsi_q, iscsi_recv_from_iscsi_q, bool, 0644);
+MODULE_PARM_DESC(recv_from_iscsi_q, "Set to true to read iSCSI data/headers from the iscsi_q workqueue. The default is false which will perform reads from the network softirq context.");
+
 static int iscsi_sw_tcp_dbg;
 module_param_named(debug_iscsi_tcp, iscsi_sw_tcp_dbg, int,
 		   S_IRUGO | S_IWUSR);
@@ -122,20 +126,13 @@
 	return 0;
 }
 
-static void iscsi_sw_tcp_data_ready(struct sock *sk)
+static void iscsi_sw_tcp_recv_data(struct iscsi_conn *conn)
 {
-	struct iscsi_conn *conn;
-	struct iscsi_tcp_conn *tcp_conn;
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct iscsi_sw_tcp_conn *tcp_sw_conn = tcp_conn->dd_data;
+	struct sock *sk = tcp_sw_conn->sock->sk;
 	read_descriptor_t rd_desc;
 
-	read_lock_bh(&sk->sk_callback_lock);
-	conn = sk->sk_user_data;
-	if (!conn) {
-		read_unlock_bh(&sk->sk_callback_lock);
-		return;
-	}
-	tcp_conn = conn->dd_data;
-
 	/*
 	 * Use rd_desc to pass 'conn' to iscsi_tcp_recv.
 	 * We set count to 1 because we want the network layer to
@@ -144,13 +141,48 @@
 	 */
 	rd_desc.arg.data = conn;
 	rd_desc.count = 1;
-	tcp_read_sock(sk, &rd_desc, iscsi_sw_tcp_recv);
 
-	iscsi_sw_sk_state_check(sk);
+	tcp_read_sock(sk, &rd_desc, iscsi_sw_tcp_recv);
 
 	/* If we had to (atomically) map a highmem page,
 	 * unmap it now. */
 	iscsi_tcp_segment_unmap(&tcp_conn->in.segment);
+
+	iscsi_sw_sk_state_check(sk);
+}
+
+static void iscsi_sw_tcp_recv_data_work(struct work_struct *work)
+{
+	struct iscsi_conn *conn = container_of(work, struct iscsi_conn,
+					       recvwork);
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct iscsi_sw_tcp_conn *tcp_sw_conn = tcp_conn->dd_data;
+	struct sock *sk = tcp_sw_conn->sock->sk;
+
+	lock_sock(sk);
+	iscsi_sw_tcp_recv_data(conn);
+	release_sock(sk);
+}
+
+static void iscsi_sw_tcp_data_ready(struct sock *sk)
+{
+	struct iscsi_sw_tcp_conn *tcp_sw_conn;
+	struct iscsi_tcp_conn *tcp_conn;
+	struct iscsi_conn *conn;
+
+	read_lock_bh(&sk->sk_callback_lock);
+	conn = sk->sk_user_data;
+	if (!conn) {
+		read_unlock_bh(&sk->sk_callback_lock);
+		return;
+	}
+	tcp_conn = conn->dd_data;
+	tcp_sw_conn = tcp_conn->dd_data;
+
+	if (tcp_sw_conn->queue_recv)
+		iscsi_conn_queue_recv(conn);
+	else
+		iscsi_sw_tcp_recv_data(conn);
 	read_unlock_bh(&sk->sk_callback_lock);
 }
 
@@ -205,7 +237,7 @@
 	old_write_space(sk);
 
 	ISCSI_SW_TCP_DBG(conn, "iscsi_write_space\n");
-	iscsi_conn_queue_work(conn);
+	iscsi_conn_queue_xmit(conn);
 }
 
 static void iscsi_sw_tcp_conn_set_callbacks(struct iscsi_conn *conn)
@@ -276,6 +308,9 @@
 		if (segment->total_copied + segment->size < segment->total_size)
 			flags |= MSG_MORE;
 
+		if (tcp_sw_conn->queue_recv)
+			flags |= MSG_DONTWAIT;
+
 		/* Use sendpage if we can; else fall back to sendmsg */
 		if (!segment->data) {
 			sg = segment->sg;
@@ -557,6 +592,10 @@
 	conn = cls_conn->dd_data;
 	tcp_conn = conn->dd_data;
 	tcp_sw_conn = tcp_conn->dd_data;
+	INIT_WORK(&conn->recvwork, iscsi_sw_tcp_recv_data_work);
+	tcp_sw_conn->queue_recv = iscsi_recv_from_iscsi_q;
+
+	mutex_init(&tcp_sw_conn->sock_lock);
 
 	tfm = crypto_alloc_ahash("crc32c", 0, CRYPTO_ALG_ASYNC);
 	if (IS_ERR(tfm))
@@ -592,11 +631,15 @@
 
 static void iscsi_sw_tcp_release_conn(struct iscsi_conn *conn)
 {
-	struct iscsi_session *session = conn->session;
 	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
 	struct iscsi_sw_tcp_conn *tcp_sw_conn = tcp_conn->dd_data;
 	struct socket *sock = tcp_sw_conn->sock;
 
+	/*
+	 * The iscsi transport class will make sure we are not called in
+	 * parallel with start, stop, bind and destroys. However, this can be
+	 * called twice if userspace does a stop then a destroy.
+	 */
 	if (!sock)
 		return;
 
@@ -610,9 +653,11 @@
 	iscsi_sw_tcp_conn_restore_callbacks(conn);
 	sock_put(sock->sk);
 
-	spin_lock_bh(&session->frwd_lock);
+	iscsi_suspend_rx(conn);
+
+	mutex_lock(&tcp_sw_conn->sock_lock);
 	tcp_sw_conn->sock = NULL;
-	spin_unlock_bh(&session->frwd_lock);
+	mutex_unlock(&tcp_sw_conn->sock_lock);
 	sockfd_put(sock);
 }
 
@@ -664,7 +709,6 @@
 		       struct iscsi_cls_conn *cls_conn, uint64_t transport_eph,
 		       int is_leading)
 {
-	struct iscsi_session *session = cls_session->dd_data;
 	struct iscsi_conn *conn = cls_conn->dd_data;
 	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
 	struct iscsi_sw_tcp_conn *tcp_sw_conn = tcp_conn->dd_data;
@@ -684,10 +728,10 @@
 	if (err)
 		goto free_socket;
 
-	spin_lock_bh(&session->frwd_lock);
+	mutex_lock(&tcp_sw_conn->sock_lock);
 	/* bind iSCSI connection and socket */
 	tcp_sw_conn->sock = sock;
-	spin_unlock_bh(&session->frwd_lock);
+	mutex_unlock(&tcp_sw_conn->sock_lock);
 
 	/* setup Socket parameters */
 	sk = sock->sk;
@@ -723,9 +767,15 @@
 		iscsi_set_param(cls_conn, param, buf, buflen);
 		break;
 	case ISCSI_PARAM_DATADGST_EN:
+		mutex_lock(&tcp_sw_conn->sock_lock);
+		if (!tcp_sw_conn->sock) {
+			mutex_unlock(&tcp_sw_conn->sock_lock);
+			return -ENOTCONN;
+		}
 		iscsi_set_param(cls_conn, param, buf, buflen);
 		tcp_sw_conn->sendpage = conn->datadgst_en ?
 			sock_no_sendpage : tcp_sw_conn->sock->ops->sendpage;
+		mutex_unlock(&tcp_sw_conn->sock_lock);
 		break;
 	case ISCSI_PARAM_MAX_R2T:
 		return iscsi_tcp_set_max_r2t(conn, buf);
@@ -740,8 +790,8 @@
 				       enum iscsi_param param, char *buf)
 {
 	struct iscsi_conn *conn = cls_conn->dd_data;
-	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
-	struct iscsi_sw_tcp_conn *tcp_sw_conn = tcp_conn->dd_data;
+	struct iscsi_sw_tcp_conn *tcp_sw_conn;
+	struct iscsi_tcp_conn *tcp_conn;
 	struct sockaddr_in6 addr;
 	struct socket *sock;
 	int rc;
@@ -751,21 +801,36 @@
 	case ISCSI_PARAM_CONN_ADDRESS:
 	case ISCSI_PARAM_LOCAL_PORT:
 		spin_lock_bh(&conn->session->frwd_lock);
-		if (!tcp_sw_conn || !tcp_sw_conn->sock) {
+		if (!conn->session->leadconn) {
 			spin_unlock_bh(&conn->session->frwd_lock);
 			return -ENOTCONN;
 		}
-		sock = tcp_sw_conn->sock;
-		sock_hold(sock->sk);
+		/*
+		 * The conn has been setup and bound, so just grab a ref
+		 * incase a destroy runs while we are in the net layer.
+		 */
+		iscsi_get_conn(conn->cls_conn);
 		spin_unlock_bh(&conn->session->frwd_lock);
 
+		tcp_conn = conn->dd_data;
+		tcp_sw_conn = tcp_conn->dd_data;
+
+		mutex_lock(&tcp_sw_conn->sock_lock);
+		sock = tcp_sw_conn->sock;
+		if (!sock) {
+			rc = -ENOTCONN;
+			goto sock_unlock;
+		}
+
 		if (param == ISCSI_PARAM_LOCAL_PORT)
 			rc = kernel_getsockname(sock,
 						(struct sockaddr *)&addr);
 		else
 			rc = kernel_getpeername(sock,
 						(struct sockaddr *)&addr);
-		sock_put(sock->sk);
+sock_unlock:
+		mutex_unlock(&tcp_sw_conn->sock_lock);
+		iscsi_put_conn(conn->cls_conn);
 		if (rc < 0)
 			return rc;
 
@@ -782,7 +847,7 @@
 				       enum iscsi_host_param param, char *buf)
 {
 	struct iscsi_sw_tcp_host *tcp_sw_host = iscsi_host_priv(shost);
-	struct iscsi_session *session = tcp_sw_host->session;
+	struct iscsi_session *session;
 	struct iscsi_conn *conn;
 	struct iscsi_tcp_conn *tcp_conn;
 	struct iscsi_sw_tcp_conn *tcp_sw_conn;
@@ -792,6 +857,7 @@
 
 	switch (param) {
 	case ISCSI_HOST_PARAM_IPADDRESS:
+		session = tcp_sw_host->session;
 		if (!session)
 			return -ENOTCONN;
 
@@ -803,17 +869,21 @@
 		}
 		tcp_conn = conn->dd_data;
 		tcp_sw_conn = tcp_conn->dd_data;
-		sock = tcp_sw_conn->sock;
-		if (!sock) {
-			spin_unlock_bh(&session->frwd_lock);
-			return -ENOTCONN;
-		}
-		sock_hold(sock->sk);
+		/*
+		 * The conn has been setup and bound, so just grab a ref
+		 * incase a destroy runs while we are in the net layer.
+		 */
+		iscsi_get_conn(conn->cls_conn);
 		spin_unlock_bh(&session->frwd_lock);
 
-		rc = kernel_getsockname(sock,
-					(struct sockaddr *)&addr);
-		sock_put(sock->sk);
+		mutex_lock(&tcp_sw_conn->sock_lock);
+		sock = tcp_sw_conn->sock;
+		if (!sock)
+			rc = -ENOTCONN;
+		else
+			rc = kernel_getsockname(sock, (struct sockaddr *)&addr);
+		mutex_unlock(&tcp_sw_conn->sock_lock);
+		iscsi_put_conn(conn->cls_conn);
 		if (rc < 0)
 			return rc;
 
@@ -888,17 +958,19 @@
 	if (!cls_session)
 		goto remove_host;
 	session = cls_session->dd_data;
-	tcp_sw_host = iscsi_host_priv(shost);
-	tcp_sw_host->session = session;
 
 	if (iscsi_tcp_r2tpool_alloc(session))
 		goto remove_session;
+
+	/* We are now fully setup so expose the session to sysfs. */
+	tcp_sw_host = iscsi_host_priv(shost);
+	tcp_sw_host->session = session;
 	return cls_session;
 
 remove_session:
 	iscsi_session_teardown(cls_session);
 remove_host:
-	iscsi_host_remove(shost);
+	iscsi_host_remove(shost, false);
 free_host:
 	iscsi_host_free(shost);
 	return NULL;
@@ -912,10 +984,17 @@
 	if (WARN_ON_ONCE(session->leadconn))
 		return;
 
+	iscsi_session_remove(cls_session);
+	/*
+	 * Our get_host_param needs to access the session, so remove the
+	 * host from sysfs before freeing the session to make sure userspace
+	 * is no longer accessing the callout.
+	 */
+	iscsi_host_remove(shost, false);
+
 	iscsi_tcp_r2tpool_free(cls_session->dd_data);
-	iscsi_session_teardown(cls_session);
 
-	iscsi_host_remove(shost);
+	iscsi_session_free(cls_session);
 	iscsi_host_free(shost);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/iscsi_tcp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/iscsi_tcp.h
@@ -28,6 +28,11 @@
 
 struct iscsi_sw_tcp_conn {
 	struct socket		*sock;
+	/* Taken when accessing the sock from the netlink/sysfs interface */
+	struct mutex		sock_lock;
+
+	struct work_struct	recvwork;
+	bool			queue_recv;
 
 	struct iscsi_sw_tcp_send out;
 	/* old values for socket callbacks */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libfc/fc_exch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libfc/fc_exch.c
@@ -1701,6 +1701,7 @@
 	if (cancel_delayed_work_sync(&ep->timeout_work)) {
 		FC_EXCH_DBG(ep, "Exchange timer canceled due to ABTS response\n");
 		fc_exch_release(ep);	/* release from pending timer hold */
+		return;
 	}
 
 	spin_lock_bh(&ep->ex_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libfc/fc_fcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libfc/fc_fcp.c
@@ -270,6 +270,11 @@
 	if (!fsp->seq_ptr)
 		return -EINVAL;
 
+	if (fsp->state & FC_SRB_ABORT_PENDING) {
+		FC_FCP_DBG(fsp, "abort already pending\n");
+		return -EBUSY;
+	}
+
 	per_cpu_ptr(fsp->lp->stats, get_cpu())->FcpPktAborts++;
 	put_cpu();
 
@@ -1681,7 +1686,7 @@
 		if (fsp->recov_retry++ < FC_MAX_RECOV_RETRY)
 			fc_fcp_rec(fsp);
 		else
-			fc_fcp_recovery(fsp, FC_ERROR);
+			fc_fcp_recovery(fsp, FC_TIMED_OUT);
 		break;
 	}
 	fc_fcp_unlock_pkt(fsp);
@@ -1700,11 +1705,12 @@
 	fsp->status_code = code;
 	fsp->cdb_status = 0;
 	fsp->io_status = 0;
-	/*
-	 * if this fails then we let the scsi command timer fire and
-	 * scsi-ml escalate.
-	 */
-	fc_fcp_send_abort(fsp);
+	if (!fsp->cmd)
+		/*
+		 * Only abort non-scsi commands; otherwise let the
+		 * scsi command timer fire and scsi-ml escalate.
+		 */
+		fc_fcp_send_abort(fsp);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libfc/fc_lport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libfc/fc_lport.c
@@ -241,6 +241,12 @@
 	}
 	mutex_lock(&lport->disc.disc_mutex);
 	lport->ptp_rdata = fc_rport_create(lport, remote_fid);
+	if (!lport->ptp_rdata) {
+		printk(KERN_WARNING "libfc: Failed to setup lport 0x%x\n",
+			lport->port_id);
+		mutex_unlock(&lport->disc.disc_mutex);
+		return;
+	}
 	kref_get(&lport->ptp_rdata->kref);
 	lport->ptp_rdata->ids.port_name = remote_wwpn;
 	lport->ptp_rdata->ids.node_name = remote_wwnn;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libiscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libiscsi.c
@@ -83,7 +83,7 @@
 				"%s " dbg_fmt, __func__, ##arg);	\
 	} while (0);
 
-inline void iscsi_conn_queue_work(struct iscsi_conn *conn)
+inline void iscsi_conn_queue_xmit(struct iscsi_conn *conn)
 {
 	struct Scsi_Host *shost = conn->session->host;
 	struct iscsi_host *ihost = shost_priv(shost);
@@ -91,7 +91,17 @@
 	if (ihost->workq)
 		queue_work(ihost->workq, &conn->xmitwork);
 }
-EXPORT_SYMBOL_GPL(iscsi_conn_queue_work);
+EXPORT_SYMBOL_GPL(iscsi_conn_queue_xmit);
+
+inline void iscsi_conn_queue_recv(struct iscsi_conn *conn)
+{
+	struct Scsi_Host *shost = conn->session->host;
+	struct iscsi_host *ihost = shost_priv(shost);
+
+	if (ihost->workq && !test_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags))
+		queue_work(ihost->workq, &conn->recvwork);
+}
+EXPORT_SYMBOL_GPL(iscsi_conn_queue_recv);
 
 static void __iscsi_update_cmdsn(struct iscsi_session *session,
 				 uint32_t exp_cmdsn, uint32_t max_cmdsn)
@@ -678,7 +688,8 @@
 	struct iscsi_task *task;
 	itt_t itt;
 
-	if (session->state == ISCSI_STATE_TERMINATE)
+	if (session->state == ISCSI_STATE_TERMINATE ||
+	    !test_bit(ISCSI_CONN_FLAG_BOUND, &conn->flags))
 		return NULL;
 
 	if (opcode == ISCSI_OP_LOGIN || opcode == ISCSI_OP_TEXT) {
@@ -764,7 +775,7 @@
 			goto free_task;
 	} else {
 		list_add_tail(&task->running, &conn->mgmtqueue);
-		iscsi_conn_queue_work(conn);
+		iscsi_conn_queue_xmit(conn);
 	}
 
 	return task;
@@ -1392,8 +1403,8 @@
 	if (conn->stop_stage == 0)
 		session->state = ISCSI_STATE_FAILED;
 
-	set_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx);
-	set_bit(ISCSI_SUSPEND_BIT, &conn->suspend_rx);
+	set_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags);
+	set_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags);
 	return true;
 }
 
@@ -1454,7 +1465,7 @@
 	 * Do this after dropping the extra ref because if this was a requeue
 	 * it's removed from that list and cleanup_queued_task would miss it.
 	 */
-	if (test_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx)) {
+	if (test_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags)) {
 		/*
 		 * Save the task and ref in case we weren't cleaning up this
 		 * task and get woken up again.
@@ -1512,7 +1523,7 @@
 		 */
 		iscsi_put_task(task);
 	}
-	iscsi_conn_queue_work(conn);
+	iscsi_conn_queue_xmit(conn);
 	spin_unlock_bh(&conn->session->frwd_lock);
 }
 EXPORT_SYMBOL_GPL(iscsi_requeue_task);
@@ -1532,7 +1543,7 @@
 	int rc = 0;
 
 	spin_lock_bh(&conn->session->frwd_lock);
-	if (test_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx)) {
+	if (test_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags)) {
 		ISCSI_DBG_SESSION(conn->session, "Tx suspended!\n");
 		spin_unlock_bh(&conn->session->frwd_lock);
 		return -ENODATA;
@@ -1746,7 +1757,7 @@
 		goto fault;
 	}
 
-	if (test_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx)) {
+	if (test_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags)) {
 		reason = FAILURE_SESSION_IN_RECOVERY;
 		sc->result = DID_REQUEUE << 16;
 		goto fault;
@@ -1781,7 +1792,7 @@
 		}
 	} else {
 		list_add_tail(&task->running, &conn->cmdqueue);
-		iscsi_conn_queue_work(conn);
+		iscsi_conn_queue_xmit(conn);
 	}
 
 	session->queued_cmdsn++;
@@ -1935,14 +1946,14 @@
 void iscsi_suspend_queue(struct iscsi_conn *conn)
 {
 	spin_lock_bh(&conn->session->frwd_lock);
-	set_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx);
+	set_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags);
 	spin_unlock_bh(&conn->session->frwd_lock);
 }
 EXPORT_SYMBOL_GPL(iscsi_suspend_queue);
 
 /**
  * iscsi_suspend_tx - suspend iscsi_data_xmit
- * @conn: iscsi conn tp stop processing IO on.
+ * @conn: iscsi conn to stop processing IO on.
  *
  * This function sets the suspend bit to prevent iscsi_data_xmit
  * from sending new IO, and if work is queued on the xmit thread
@@ -1953,17 +1964,32 @@
 	struct Scsi_Host *shost = conn->session->host;
 	struct iscsi_host *ihost = shost_priv(shost);
 
-	set_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx);
+	set_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags);
 	if (ihost->workq)
-		flush_workqueue(ihost->workq);
+		flush_work(&conn->xmitwork);
 }
 EXPORT_SYMBOL_GPL(iscsi_suspend_tx);
 
 static void iscsi_start_tx(struct iscsi_conn *conn)
 {
-	clear_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx);
-	iscsi_conn_queue_work(conn);
+	clear_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags);
+	iscsi_conn_queue_xmit(conn);
+}
+
+/**
+ * iscsi_suspend_rx - Prevent recvwork from running again.
+ * @conn: iscsi conn to stop.
+ */
+void iscsi_suspend_rx(struct iscsi_conn *conn)
+{
+	struct Scsi_Host *shost = conn->session->host;
+	struct iscsi_host *ihost = shost_priv(shost);
+
+	set_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags);
+	if (ihost->workq)
+		flush_work(&conn->recvwork);
 }
+EXPORT_SYMBOL_GPL(iscsi_suspend_rx);
 
 /*
  * We want to make sure a ping is in flight. It has timed out.
@@ -2214,6 +2240,8 @@
 	iscsi_suspend_tx(conn);
 
 	spin_lock_bh(&session->frwd_lock);
+	clear_bit(ISCSI_CONN_FLAG_BOUND, &conn->flags);
+
 	if (!is_active) {
 		/*
 		 * if logout timed out before userspace could even send a PDU
@@ -2827,11 +2855,12 @@
 /**
  * iscsi_host_remove - remove host and sessions
  * @shost: scsi host
+ * @is_shutdown: true if called from a driver shutdown callout
  *
  * If there are any sessions left, this will initiate the removal and wait
  * for the completion.
  */
-void iscsi_host_remove(struct Scsi_Host *shost)
+void iscsi_host_remove(struct Scsi_Host *shost, bool is_shutdown)
 {
 	struct iscsi_host *ihost = shost_priv(shost);
 	unsigned long flags;
@@ -2840,7 +2869,11 @@
 	ihost->state = ISCSI_HOST_REMOVED;
 	spin_unlock_irqrestore(&ihost->lock, flags);
 
-	iscsi_host_for_each_session(shost, iscsi_notify_host_removed);
+	if (!is_shutdown)
+		iscsi_host_for_each_session(shost, iscsi_notify_host_removed);
+	else
+		iscsi_host_for_each_session(shost, iscsi_force_destroy_session);
+
 	wait_event_interruptible(ihost->session_removal_wq,
 				 ihost->num_sessions == 0);
 	if (signal_pending(current))
@@ -2991,17 +3024,32 @@
 }
 EXPORT_SYMBOL_GPL(iscsi_session_setup);
 
-/**
- * iscsi_session_teardown - destroy session, host, and cls_session
- * @cls_session: iscsi session
+/*
+ * issi_session_remove - Remove session from iSCSI class.
  */
-void iscsi_session_teardown(struct iscsi_cls_session *cls_session)
+void iscsi_session_remove(struct iscsi_cls_session *cls_session)
 {
 	struct iscsi_session *session = cls_session->dd_data;
-	struct module *owner = cls_session->transport->owner;
 	struct Scsi_Host *shost = session->host;
 
 	iscsi_remove_session(cls_session);
+	/*
+	 * host removal only has to wait for its children to be removed from
+	 * sysfs, and iscsi_tcp needs to do iscsi_host_remove before freeing
+	 * the session, so drop the session count here.
+	 */
+	iscsi_host_dec_session_cnt(shost);
+}
+EXPORT_SYMBOL_GPL(iscsi_session_remove);
+
+/**
+ * iscsi_session_free - Free iscsi session and it's resources
+ * @cls_session: iscsi session
+ */
+void iscsi_session_free(struct iscsi_cls_session *cls_session)
+{
+	struct iscsi_session *session = cls_session->dd_data;
+	struct module *owner = cls_session->transport->owner;
 
 	iscsi_pool_free(&session->cmdpool);
 	kfree(session->password);
@@ -3019,10 +3067,19 @@
 	kfree(session->discovery_parent_type);
 
 	iscsi_free_session(cls_session);
-
-	iscsi_host_dec_session_cnt(shost);
 	module_put(owner);
 }
+EXPORT_SYMBOL_GPL(iscsi_session_free);
+
+/**
+ * iscsi_session_teardown - destroy session and cls_session
+ * @cls_session: iscsi session
+ */
+void iscsi_session_teardown(struct iscsi_cls_session *cls_session)
+{
+	iscsi_session_remove(cls_session);
+	iscsi_session_free(cls_session);
+}
 EXPORT_SYMBOL_GPL(iscsi_session_teardown);
 
 /**
@@ -3101,6 +3158,8 @@
 {
 	struct iscsi_conn *conn = cls_conn->dd_data;
 	struct iscsi_session *session = conn->session;
+	char *tmp_persistent_address = conn->persistent_address;
+	char *tmp_local_ipaddr = conn->local_ipaddr;
 
 	del_timer_sync(&conn->transport_timer);
 
@@ -3122,8 +3181,6 @@
 	spin_lock_bh(&session->frwd_lock);
 	free_pages((unsigned long) conn->data,
 		   get_order(ISCSI_DEF_MAX_RECV_SEG_LEN));
-	kfree(conn->persistent_address);
-	kfree(conn->local_ipaddr);
 	/* regular RX path uses back_lock */
 	spin_lock_bh(&session->back_lock);
 	kfifo_in(&session->cmdpool.queue, (void*)&conn->login_task,
@@ -3135,6 +3192,8 @@
 	mutex_unlock(&session->eh_mutex);
 
 	iscsi_destroy_conn(cls_conn);
+	kfree(tmp_persistent_address);
+	kfree(tmp_local_ipaddr);
 }
 EXPORT_SYMBOL_GPL(iscsi_conn_teardown);
 
@@ -3310,6 +3369,8 @@
 	spin_lock_bh(&session->frwd_lock);
 	if (is_leading)
 		session->leadconn = conn;
+
+	set_bit(ISCSI_CONN_FLAG_BOUND, &conn->flags);
 	spin_unlock_bh(&session->frwd_lock);
 
 	/*
@@ -3322,8 +3383,8 @@
 	/*
 	 * Unblock xmitworker(), Login Phase will pass through.
 	 */
-	clear_bit(ISCSI_SUSPEND_BIT, &conn->suspend_rx);
-	clear_bit(ISCSI_SUSPEND_BIT, &conn->suspend_tx);
+	clear_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags);
+	clear_bit(ISCSI_CONN_FLAG_SUSPEND_TX, &conn->flags);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(iscsi_conn_bind);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libiscsi_tcp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libiscsi_tcp.c
@@ -927,7 +927,7 @@
 	 */
 	conn->last_recv = jiffies;
 
-	if (unlikely(conn->suspend_rx)) {
+	if (unlikely(test_bit(ISCSI_CONN_FLAG_SUSPEND_RX, &conn->flags))) {
 		ISCSI_DBG_TCP(conn, "Rx suspended!\n");
 		*status = ISCSI_TCP_SUSPENDED;
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libsas/sas_ata.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libsas/sas_ata.c
@@ -197,7 +197,7 @@
 		task->total_xfer_len = qc->nbytes;
 		task->num_scatter = qc->n_elem;
 		task->data_dir = qc->dma_dir;
-	} else if (qc->tf.protocol == ATA_PROT_NODATA) {
+	} else if (!ata_is_data(qc->tf.protocol)) {
 		task->data_dir = DMA_NONE;
 	} else {
 		for_each_sg(qc->sg, sg, qc->n_elem, si)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libsas/sas_expander.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libsas/sas_expander.c
@@ -85,7 +85,7 @@
 		res = i->dft->lldd_execute_task(task, GFP_KERNEL);
 
 		if (res) {
-			del_timer(&task->slow_task->timer);
+			del_timer_sync(&task->slow_task->timer);
 			pr_notice("executing SMP task failed:%d\n", res);
 			break;
 		}
@@ -256,8 +256,7 @@
 	/* help some expanders that fail to zero sas_address in the 'no
 	 * device' case
 	 */
-	if (phy->attached_dev_type == SAS_PHY_UNUSED ||
-	    phy->linkrate < SAS_LINK_RATE_1_5_GBPS)
+	if (phy->attached_dev_type == SAS_PHY_UNUSED)
 		memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE);
 	else
 		memcpy(phy->attached_sas_addr, dr->attached_sas_addr, SAS_ADDR_SIZE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libsas/sas_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libsas/sas_internal.h
@@ -111,6 +111,20 @@
 		func, dev->parent ? "exp-attached" :
 		"direct-attached",
 		SAS_ADDR(dev->sas_addr), err);
+
+	/*
+	 * If the device probe failed, the expander phy attached address
+	 * needs to be reset so that the phy will not be treated as flutter
+	 * in the next revalidation
+	 */
+	if (dev->parent && !dev_is_expander(dev->dev_type)) {
+		struct sas_phy *phy = dev->phy;
+		struct domain_device *parent = dev->parent;
+		struct ex_phy *ex_phy = &parent->ex_dev.ex_phy[phy->number];
+
+		memset(ex_phy->attached_sas_addr, 0, SAS_ADDR_SIZE);
+	}
+
 	sas_unregister_dev(dev->port, dev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/libsas/sas_scsi_host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/libsas/sas_scsi_host.c
@@ -466,6 +466,9 @@
 	struct sas_internal *i = to_sas_internal(host->transportt);
 	unsigned long flags;
 
+	if (current != host->ehandler)
+		return FAILED;
+
 	if (!i->dft->lldd_abort_task)
 		return FAILED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc.h
@@ -32,6 +32,7 @@
 struct lpfc_sli2_slim;
 
 #define ELX_MODEL_NAME_SIZE	80
+#define ELX_FW_NAME_SIZE	84
 
 #define LPFC_PCI_DEV_LP		0x1
 #define LPFC_PCI_DEV_OC		0x2
@@ -593,6 +594,7 @@
 #define FC_VPORT_LOGO_RCVD      0x200    /* LOGO received on vport */
 #define FC_RSCN_DISCOVERY       0x400	 /* Auth all devices after RSCN */
 #define FC_LOGO_RCVD_DID_CHNG   0x800    /* FDISC on phys port detect DID chng*/
+#define FC_PT2PT_NO_NVME        0x1000   /* Don't send NVME PRLI */
 #define FC_SCSI_SCAN_TMO        0x4000	 /* scsi scan timer running */
 #define FC_ABORT_DISCOVERY      0x8000	 /* we want to abort discovery */
 #define FC_NDISC_ACTIVE         0x10000	 /* NPort discovery active */
@@ -668,8 +670,6 @@
 	struct timer_list els_tmofunc;
 	struct timer_list delayed_disc_tmo;
 
-	int unreg_vpi_cmpl;
-
 	uint8_t load_flag;
 #define FC_LOADING		0x1	/* HBA in process of loading drvr */
 #define FC_UNLOADING		0x2	/* HBA in process of unloading drvr */
@@ -1022,14 +1022,14 @@
 #define HBA_DEVLOSS_TMO         0x2000 /* HBA in devloss timeout */
 #define HBA_RRQ_ACTIVE		0x4000 /* process the rrq active list */
 #define HBA_IOQ_FLUSH		0x8000 /* FCP/NVME I/O queues being flushed */
-#define HBA_FW_DUMP_OP		0x10000 /* Skips fn reset before FW dump */
 #define HBA_RECOVERABLE_UE	0x20000 /* Firmware supports recoverable UE */
 #define HBA_FORCED_LINK_SPEED	0x40000 /*
 					 * Firmware supports Forced Link Speed
 					 * capability
 					 */
+#define HBA_PCI_ERR		0x80000 /* The PCI slot is offline */
 #define HBA_FLOGI_ISSUED	0x100000 /* FLOGI was issued */
-#define HBA_CGN_RSVD1		0x200000 /* Reserved CGN flag */
+#define HBA_SHORT_CMF		0x200000 /* shorter CMF timer routine */
 #define HBA_CGN_DAY_WRAP	0x400000 /* HBA Congestion info day wraps */
 #define HBA_DEFER_FLOGI		0x800000 /* Defer FLOGI till read_sparm cmpl */
 #define HBA_SETUP		0x1000000 /* Signifies HBA setup is completed */
@@ -1038,6 +1038,7 @@
 #define HBA_HBEAT_TMO		0x8000000 /* HBEAT initiated after timeout */
 #define HBA_FLOGI_OUTSTANDING	0x10000000 /* FLOGI is outstanding */
 
+	struct completion *fw_dump_cmpl; /* cmpl event tracker for fw_dump */
 	uint32_t fcp_ring_in_use; /* When polling test if intr-hndlr active*/
 	struct lpfc_dmabuf slim2p;
 
@@ -1163,6 +1164,16 @@
 	uint32_t cfg_hostmem_hgp;
 	uint32_t cfg_log_verbose;
 	uint32_t cfg_enable_fc4_type;
+#define LPFC_ENABLE_FCP  1
+#define LPFC_ENABLE_NVME 2
+#define LPFC_ENABLE_BOTH 3
+#if (IS_ENABLED(CONFIG_NVME_FC))
+#define LPFC_MAX_ENBL_FC4_TYPE LPFC_ENABLE_BOTH
+#define LPFC_DEF_ENBL_FC4_TYPE LPFC_ENABLE_BOTH
+#else
+#define LPFC_MAX_ENBL_FC4_TYPE LPFC_ENABLE_FCP
+#define LPFC_DEF_ENBL_FC4_TYPE LPFC_ENABLE_FCP
+#endif
 	uint32_t cfg_aer_support;
 	uint32_t cfg_sriov_nr_virtfn;
 	uint32_t cfg_request_firmware_upgrade;
@@ -1184,9 +1195,6 @@
 	uint32_t cfg_ras_fwlog_func;
 	uint32_t cfg_enable_bbcr;	/* Enable BB Credit Recovery */
 	uint32_t cfg_enable_dpp;	/* Enable Direct Packet Push */
-#define LPFC_ENABLE_FCP  1
-#define LPFC_ENABLE_NVME 2
-#define LPFC_ENABLE_BOTH 3
 	uint32_t cfg_enable_pbde;
 	uint32_t cfg_enable_mi;
 	struct nvmet_fc_target_port *targetport;
@@ -1331,7 +1339,6 @@
 	unsigned long bit_flags;
 #define	FABRIC_COMANDS_BLOCKED	0
 	atomic_t num_rsrc_err;
-	atomic_t num_cmd_success;
 	unsigned long last_rsrc_error_time;
 	unsigned long last_ramp_down_time;
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
@@ -1549,10 +1556,7 @@
 	u32 cgn_acqe_cnt;
 
 	/* RX monitor handling for CMF */
-	struct rxtable_entry *rxtable;  /* RX_monitor information */
-	atomic_t rxtable_idx_head;
-#define LPFC_RXMONITOR_TABLE_IN_USE     (LPFC_MAX_RXMONITOR_ENTRY + 73)
-	atomic_t rxtable_idx_tail;
+	struct lpfc_rx_info_monitor *rx_monitor;
 	atomic_t rx_max_read_cnt;       /* Maximum read bytes */
 	uint64_t rx_block_cnt;
 
@@ -1601,7 +1605,8 @@
 
 #define LPFC_MAX_RXMONITOR_ENTRY	800
 #define LPFC_MAX_RXMONITOR_DUMP		32
-struct rxtable_entry {
+struct rx_info_entry {
+	uint64_t cmf_bytes;	/* Total no of read bytes for CMF_SYNC_WQE */
 	uint64_t total_bytes;   /* Total no of read bytes requested */
 	uint64_t rcv_bytes;     /* Total no of read bytes completed */
 	uint64_t avg_io_size;
@@ -1615,6 +1620,13 @@
 	uint32_t timer_interval;
 };
 
+struct lpfc_rx_info_monitor {
+	struct rx_info_entry *ring; /* info organized in a circular buffer */
+	u32 head_idx, tail_idx; /* index to head/tail of ring */
+	spinlock_t lock; /* spinlock for ring */
+	u32 entries; /* storing number entries/size of ring */
+};
+
 static inline struct Scsi_Host *
 lpfc_shost_from_vport(struct lpfc_vport *vport)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_attr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_attr.c
@@ -1315,6 +1315,9 @@
 	pmboxq->u.mb.mbxCommand = MBX_DOWN_LINK;
 	pmboxq->u.mb.mbxOwner = OWN_HOST;
 
+	if ((vport->fc_flag & FC_PT2PT) && (vport->fc_flag & FC_PT2PT_NO_NVME))
+		vport->fc_flag &= ~FC_PT2PT_NO_NVME;
+
 	mbxstatus = lpfc_sli_issue_mbox_wait(phba, pmboxq, LPFC_MBOX_TMO * 2);
 
 	if ((mbxstatus == MBX_SUCCESS) &&
@@ -1709,25 +1712,25 @@
 	before_fc_flag = phba->pport->fc_flag;
 	sriov_nr_virtfn = phba->cfg_sriov_nr_virtfn;
 
-	/* Disable SR-IOV virtual functions if enabled */
-	if (phba->cfg_sriov_nr_virtfn) {
-		pci_disable_sriov(pdev);
-		phba->cfg_sriov_nr_virtfn = 0;
-	}
+	if (opcode == LPFC_FW_DUMP) {
+		init_completion(&online_compl);
+		phba->fw_dump_cmpl = &online_compl;
+	} else {
+		/* Disable SR-IOV virtual functions if enabled */
+		if (phba->cfg_sriov_nr_virtfn) {
+			pci_disable_sriov(pdev);
+			phba->cfg_sriov_nr_virtfn = 0;
+		}
 
-	if (opcode == LPFC_FW_DUMP)
-		phba->hba_flag |= HBA_FW_DUMP_OP;
+		status = lpfc_do_offline(phba, LPFC_EVT_OFFLINE);
 
-	status = lpfc_do_offline(phba, LPFC_EVT_OFFLINE);
+		if (status != 0)
+			return status;
 
-	if (status != 0) {
-		phba->hba_flag &= ~HBA_FW_DUMP_OP;
-		return status;
+		/* wait for the device to be quiesced before firmware reset */
+		msleep(100);
 	}
 
-	/* wait for the device to be quiesced before firmware reset */
-	msleep(100);
-
 	reg_val = readl(phba->sli4_hba.conf_regs_memmap_p +
 			LPFC_CTL_PDEV_CTL_OFFSET);
 
@@ -1756,24 +1759,42 @@
 		lpfc_printf_log(phba, KERN_ERR, LOG_SLI,
 				"3153 Fail to perform the requested "
 				"access: x%x\n", reg_val);
+		if (phba->fw_dump_cmpl)
+			phba->fw_dump_cmpl = NULL;
 		return rc;
 	}
 
 	/* keep the original port state */
-	if (before_fc_flag & FC_OFFLINE_MODE)
-		goto out;
-
-	init_completion(&online_compl);
-	job_posted = lpfc_workq_post_event(phba, &status, &online_compl,
-					   LPFC_EVT_ONLINE);
-	if (!job_posted)
+	if (before_fc_flag & FC_OFFLINE_MODE) {
+		if (phba->fw_dump_cmpl)
+			phba->fw_dump_cmpl = NULL;
 		goto out;
+	}
 
-	wait_for_completion(&online_compl);
+	/* Firmware dump will trigger an HA_ERATT event, and
+	 * lpfc_handle_eratt_s4 routine already handles bringing the port back
+	 * online.
+	 */
+	if (opcode == LPFC_FW_DUMP) {
+		wait_for_completion(phba->fw_dump_cmpl);
+	} else  {
+		init_completion(&online_compl);
+		job_posted = lpfc_workq_post_event(phba, &status, &online_compl,
+						   LPFC_EVT_ONLINE);
+		if (!job_posted)
+			goto out;
 
+		wait_for_completion(&online_compl);
+	}
 out:
 	/* in any case, restore the virtual functions enabled as before */
 	if (sriov_nr_virtfn) {
+		/* If fw_dump was performed, first disable to clean up */
+		if (opcode == LPFC_FW_DUMP) {
+			pci_disable_sriov(pdev);
+			phba->cfg_sriov_nr_virtfn = 0;
+		}
+
 		sriov_err =
 			lpfc_sli_probe_sriov_nr_virtfn(phba, sriov_nr_virtfn);
 		if (!sriov_err)
@@ -3960,8 +3981,8 @@
  *                    3 - register both FCP and NVME
  * Supported values are [1,3]. Default value is 3
  */
-LPFC_ATTR_R(enable_fc4_type, LPFC_ENABLE_BOTH,
-	    LPFC_ENABLE_FCP, LPFC_ENABLE_BOTH,
+LPFC_ATTR_R(enable_fc4_type, LPFC_DEF_ENBL_FC4_TYPE,
+	    LPFC_ENABLE_FCP, LPFC_MAX_ENBL_FC4_TYPE,
 	    "Enable FC4 Protocol support - FCP / NVME");
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_bsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_bsg.c
@@ -911,7 +911,7 @@
 			struct lpfc_iocbq *piocbq)
 {
 	uint32_t evt_req_id = 0;
-	uint32_t cmd;
+	u16 cmd;
 	struct lpfc_dmabuf *dmabuf = NULL;
 	struct lpfc_bsg_event *evt;
 	struct event_data *evt_dat = NULL;
@@ -936,7 +936,7 @@
 
 	ct_req = (struct lpfc_sli_ct_request *)bdeBuf1->virt;
 	evt_req_id = ct_req->FsType;
-	cmd = ct_req->CommandResponse.bits.CmdRsp;
+	cmd = be16_to_cpu(ct_req->CommandResponse.bits.CmdRsp);
 
 	spin_lock_irqsave(&phba->ct_ev_lock, flags);
 	list_for_each_entry(evt, &phba->ct_ev_waiters, node) {
@@ -3243,8 +3243,8 @@
 			ctreq->RevisionId.bits.InId = 0;
 			ctreq->FsType = SLI_CT_ELX_LOOPBACK;
 			ctreq->FsSubType = 0;
-			ctreq->CommandResponse.bits.CmdRsp = ELX_LOOPBACK_DATA;
-			ctreq->CommandResponse.bits.Size   = size;
+			ctreq->CommandResponse.bits.CmdRsp = cpu_to_be16(ELX_LOOPBACK_DATA);
+			ctreq->CommandResponse.bits.Size   = cpu_to_be16(size);
 			segment_offset = ELX_LOOPBACK_HEADER_SZ;
 		} else
 			segment_offset = 0;
@@ -5761,7 +5761,7 @@
 	struct get_cgnbuf_info_req *cgnbuf_req;
 	struct lpfc_cgn_info *cp;
 	uint8_t *cgn_buff;
-	int size, cinfosz;
+	size_t size, cinfosz;
 	int  rc = 0;
 
 	if (job->request_len < sizeof(struct fc_bsg_request) +
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_crtn.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_crtn.h
@@ -90,6 +90,14 @@
 void lpfc_cgn_update_stat(struct lpfc_hba *phba, uint32_t dtag);
 void lpfc_unblock_requests(struct lpfc_hba *phba);
 void lpfc_block_requests(struct lpfc_hba *phba);
+int lpfc_rx_monitor_create_ring(struct lpfc_rx_info_monitor *rx_monitor,
+				u32 entries);
+void lpfc_rx_monitor_destroy_ring(struct lpfc_rx_info_monitor *rx_monitor);
+void lpfc_rx_monitor_record(struct lpfc_rx_info_monitor *rx_monitor,
+			    struct rx_info_entry *entry);
+u32 lpfc_rx_monitor_report(struct lpfc_hba *phba,
+			   struct lpfc_rx_info_monitor *rx_monitor, char *buf,
+			   u32 buf_len, u32 max_read_entries);
 
 void lpfc_mbx_cmpl_local_config_link(struct lpfc_hba *, LPFC_MBOXQ_t *);
 void lpfc_mbx_cmpl_reg_login(struct lpfc_hba *, LPFC_MBOXQ_t *);
@@ -119,6 +127,8 @@
 struct lpfc_nodelist *lpfc_nlp_init(struct lpfc_vport *vport, uint32_t did);
 struct lpfc_nodelist *lpfc_nlp_get(struct lpfc_nodelist *);
 int  lpfc_nlp_put(struct lpfc_nodelist *);
+void lpfc_check_nlp_post_devloss(struct lpfc_vport *vport,
+				 struct lpfc_nodelist *ndlp);
 void lpfc_ignore_els_cmpl(struct lpfc_hba *phba, struct lpfc_iocbq *cmdiocb,
 			  struct lpfc_iocbq *rspiocb);
 int  lpfc_nlp_not_used(struct lpfc_nodelist *ndlp);
@@ -205,6 +215,7 @@
 int lpfc_config_port_prep(struct lpfc_hba *);
 void lpfc_update_vport_wwn(struct lpfc_vport *vport);
 int lpfc_config_port_post(struct lpfc_hba *);
+int lpfc_sli4_refresh_params(struct lpfc_hba *phba);
 int lpfc_hba_down_prep(struct lpfc_hba *);
 int lpfc_hba_down_post(struct lpfc_hba *);
 void lpfc_hba_init(struct lpfc_hba *, uint32_t *);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_debugfs.c
@@ -2157,10 +2157,13 @@
 	char mybuf[64];
 	char *pbuf;
 	int i;
+	size_t bsize;
 
 	memset(mybuf, 0, sizeof(mybuf));
 
-	if (copy_from_user(mybuf, buf, nbytes))
+	bsize = min(nbytes, (sizeof(mybuf) - 1));
+
+	if (copy_from_user(mybuf, buf, bsize))
 		return -EFAULT;
 	pbuf = &mybuf[0];
 
@@ -2181,7 +2184,7 @@
 			qp->lock_conflict.wq_access = 0;
 		}
 	}
-	return nbytes;
+	return bsize;
 }
 #endif
 
@@ -2607,8 +2610,8 @@
 	struct lpfc_sli4_hdw_queue *qp;
 	struct lpfc_multixri_pool *multixri_pool;
 
-	if (nbytes > 64)
-		nbytes = 64;
+	if (nbytes > sizeof(mybuf) - 1)
+		nbytes = sizeof(mybuf) - 1;
 
 	memset(mybuf, 0, sizeof(mybuf));
 
@@ -2688,8 +2691,8 @@
 	if (!phba->targetport)
 		return -ENXIO;
 
-	if (nbytes > 64)
-		nbytes = 64;
+	if (nbytes > sizeof(mybuf) - 1)
+		nbytes = sizeof(mybuf) - 1;
 
 	memset(mybuf, 0, sizeof(mybuf));
 
@@ -2826,8 +2829,8 @@
 	char mybuf[64];
 	char *pbuf;
 
-	if (nbytes > 64)
-		nbytes = 64;
+	if (nbytes > sizeof(mybuf) - 1)
+		nbytes = sizeof(mybuf) - 1;
 
 	memset(mybuf, 0, sizeof(mybuf));
 
@@ -2954,8 +2957,8 @@
 	char mybuf[64];
 	char *pbuf;
 
-	if (nbytes > 64)
-		nbytes = 64;
+	if (nbytes > sizeof(mybuf) - 1)
+		nbytes = sizeof(mybuf) - 1;
 
 	memset(mybuf, 0, sizeof(mybuf));
 
@@ -3060,8 +3063,8 @@
 	char *pbuf;
 	int i;
 
-	if (nbytes > 64)
-		nbytes = 64;
+	if (nbytes > sizeof(mybuf) - 1)
+		nbytes = sizeof(mybuf) - 1;
 
 	memset(mybuf, 0, sizeof(mybuf));
 
@@ -5484,7 +5487,7 @@
 		if (len > (LPFC_CGN_BUF_SIZE - LPFC_DEBUG_OUT_LINE_SZ)) {
 			len += scnprintf(buffer + len, LPFC_CGN_BUF_SIZE - len,
 					 "Truncated . . .\n");
-			break;
+			goto out;
 		}
 		len += scnprintf(buffer + len, LPFC_CGN_BUF_SIZE - len,
 				 "%03x: %08x %08x %08x %08x "
@@ -5495,6 +5498,17 @@
 		cnt += 32;
 		ptr += 8;
 	}
+	if (len > (LPFC_CGN_BUF_SIZE - LPFC_DEBUG_OUT_LINE_SZ)) {
+		len += scnprintf(buffer + len, LPFC_CGN_BUF_SIZE - len,
+				 "Truncated . . .\n");
+		goto out;
+	}
+	len += scnprintf(buffer + len, LPFC_CGN_BUF_SIZE - len,
+			 "Parameter Data\n");
+	ptr = (uint32_t *)&phba->cgn_p;
+	len += scnprintf(buffer + len, LPFC_CGN_BUF_SIZE - len,
+			 "%08x %08x %08x %08x\n",
+			 *ptr, *(ptr + 1), *(ptr + 2), *(ptr + 3));
 out:
 	return simple_read_from_buffer(buf, nbytes, ppos, buffer, len);
 }
@@ -5520,7 +5534,7 @@
 	if (!debug)
 		goto out;
 
-	debug->buffer = vmalloc(MAX_DEBUGFS_RX_TABLE_SIZE);
+	debug->buffer = vmalloc(MAX_DEBUGFS_RX_INFO_SIZE);
 	if (!debug->buffer) {
 		kfree(debug);
 		goto out;
@@ -5541,55 +5555,18 @@
 	struct lpfc_rx_monitor_debug *debug = file->private_data;
 	struct lpfc_hba *phba = (struct lpfc_hba *)debug->i_private;
 	char *buffer = debug->buffer;
-	struct rxtable_entry *entry;
-	int i, len = 0, head, tail, last, start;
 
-	head = atomic_read(&phba->rxtable_idx_head);
-	while (head == LPFC_RXMONITOR_TABLE_IN_USE) {
-		/* Table is getting updated */
-		msleep(20);
-		head = atomic_read(&phba->rxtable_idx_head);
-	}
-
-	tail = atomic_xchg(&phba->rxtable_idx_tail, head);
-	if (!phba->rxtable || head == tail) {
-		len += scnprintf(buffer + len, MAX_DEBUGFS_RX_TABLE_SIZE - len,
-				"Rxtable is empty\n");
-		goto out;
+	if (!phba->rx_monitor) {
+		scnprintf(buffer, MAX_DEBUGFS_RX_INFO_SIZE,
+			  "Rx Monitor Info is empty.\n");
+	} else {
+		lpfc_rx_monitor_report(phba, phba->rx_monitor, buffer,
+				       MAX_DEBUGFS_RX_INFO_SIZE,
+				       LPFC_MAX_RXMONITOR_ENTRY);
 	}
-	last = (head > tail) ?  head : LPFC_MAX_RXMONITOR_ENTRY;
-	start = tail;
 
-	len += scnprintf(buffer + len, MAX_DEBUGFS_RX_TABLE_SIZE - len,
-			"        MaxBPI\t Total Data Cmd  Total Data Cmpl "
-			"  Latency(us)    Avg IO Size\tMax IO Size   IO cnt "
-			"Info BWutil(ms)\n");
-get_table:
-	for (i = start; i < last; i++) {
-		entry = &phba->rxtable[i];
-		len += scnprintf(buffer + len, MAX_DEBUGFS_RX_TABLE_SIZE - len,
-				"%3d:%12lld  %12lld\t%12lld\t"
-				"%8lldus\t%8lld\t%10lld "
-				"%8d   %2d %2d(%2d)\n",
-				i, entry->max_bytes_per_interval,
-				entry->total_bytes,
-				entry->rcv_bytes,
-				entry->avg_io_latency,
-				entry->avg_io_size,
-				entry->max_read_cnt,
-				entry->io_cnt,
-				entry->cmf_info,
-				entry->timer_utilization,
-				entry->timer_interval);
-	}
-
-	if (head != last) {
-		start = 0;
-		last = head;
-		goto get_table;
-	}
-out:
-	return simple_read_from_buffer(buf, nbytes, ppos, buffer, len);
+	return simple_read_from_buffer(buf, nbytes, ppos, buffer,
+				       strlen(buffer));
 }
 
 static int
@@ -6092,7 +6069,7 @@
 					    phba->hba_debugfs_root,
 					    phba,
 					    &lpfc_debugfs_op_multixripools);
-		if (!phba->debug_multixri_pools) {
+		if (IS_ERR(phba->debug_multixri_pools)) {
 			lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 					 "0527 Cannot create debugfs multixripools\n");
 			goto debug_failed;
@@ -6104,7 +6081,7 @@
 			debugfs_create_file(name, S_IFREG | 0644,
 					    phba->hba_debugfs_root,
 					    phba, &lpfc_cgn_buffer_op);
-		if (!phba->debug_cgn_buffer) {
+		if (IS_ERR(phba->debug_cgn_buffer)) {
 			lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 					 "6527 Cannot create debugfs "
 					 "cgn_buffer\n");
@@ -6117,7 +6094,7 @@
 			debugfs_create_file(name, S_IFREG | 0644,
 					    phba->hba_debugfs_root,
 					    phba, &lpfc_rx_monitor_op);
-		if (!phba->debug_rx_monitor) {
+		if (IS_ERR(phba->debug_rx_monitor)) {
 			lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 					 "6528 Cannot create debugfs "
 					 "rx_monitor\n");
@@ -6130,7 +6107,7 @@
 			debugfs_create_file(name, 0644,
 					    phba->hba_debugfs_root,
 					    phba, &lpfc_debugfs_ras_log);
-		if (!phba->debug_ras_log) {
+		if (IS_ERR(phba->debug_ras_log)) {
 			lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 					 "6148 Cannot create debugfs"
 					 " ras_log\n");
@@ -6151,7 +6128,7 @@
 			debugfs_create_file(name, S_IFREG | 0644,
 					    phba->hba_debugfs_root,
 					    phba, &lpfc_debugfs_op_lockstat);
-		if (!phba->debug_lockstat) {
+		if (IS_ERR(phba->debug_lockstat)) {
 			lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 					 "4610 Can't create debugfs lockstat\n");
 			goto debug_failed;
@@ -6380,7 +6357,7 @@
 		debugfs_create_file(name, 0644,
 				    vport->vport_debugfs_root,
 				    vport, &lpfc_debugfs_op_scsistat);
-	if (!vport->debug_scsistat) {
+	if (IS_ERR(vport->debug_scsistat)) {
 		lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 				 "4611 Cannot create debugfs scsistat\n");
 		goto debug_failed;
@@ -6391,7 +6368,7 @@
 		debugfs_create_file(name, 0644,
 				    vport->vport_debugfs_root,
 				    vport, &lpfc_debugfs_op_ioktime);
-	if (!vport->debug_ioktime) {
+	if (IS_ERR(vport->debug_ioktime)) {
 		lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
 				 "0815 Cannot create debugfs ioktime\n");
 		goto debug_failed;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_debugfs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_debugfs.h
@@ -282,7 +282,7 @@
 	void *ptr_private;
 };
 
-#define MAX_DEBUGFS_RX_TABLE_SIZE	(100 * LPFC_MAX_RXMONITOR_ENTRY)
+#define MAX_DEBUGFS_RX_INFO_SIZE	(128 * LPFC_MAX_RXMONITOR_ENTRY)
 struct lpfc_rx_monitor_debug {
 	char *i_private;
 	char *buffer;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_disc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_disc.h
@@ -85,6 +85,13 @@
 	NLP_XPT_HAS_HH		= 0x10
 };
 
+enum lpfc_nlp_save_flags {
+	/* devloss occurred during recovery */
+	NLP_IN_RECOV_POST_DEV_LOSS	= 0x1,
+	/* wait for outstanding LOGO to cmpl */
+	NLP_WAIT_FOR_LOGO		= 0x2,
+};
+
 struct lpfc_nodelist {
 	struct list_head nlp_listp;
 	struct serv_parm fc_sparam;		/* buffer for service params */
@@ -144,8 +151,9 @@
 	unsigned long *active_rrqs_xri_bitmap;
 	struct lpfc_scsicmd_bkt *lat_data;	/* Latency data */
 	uint32_t fc4_prli_sent;
-	u32 upcall_flags;
-#define	NLP_WAIT_FOR_LOGO 0x2
+
+	/* flags to keep ndlp alive until special conditions are met */
+	enum lpfc_nlp_save_flags save_flags;
 
 	enum lpfc_fc4_xpt_flags fc4_xpt_flags;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_els.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_els.c
@@ -1059,9 +1059,10 @@
 
 		lpfc_printf_vlog(vport, KERN_WARNING, LOG_TRACE_EVENT,
 				 "0150 FLOGI failure Status:x%x/x%x "
-				 "xri x%x TMO:x%x\n",
+				 "xri x%x TMO:x%x refcnt %d\n",
 				 irsp->ulpStatus, irsp->un.ulpWord[4],
-				 cmdiocb->sli4_xritag, irsp->ulpTimeout);
+				 cmdiocb->sli4_xritag, irsp->ulpTimeout,
+				 kref_read(&ndlp->kref));
 
 		/* If this is not a loop open failure, bail out */
 		if (!(irsp->ulpStatus == IOSTAT_LOCAL_REJECT &&
@@ -1071,7 +1072,8 @@
 
 		/* FLOGI failed, so there is no fabric */
 		spin_lock_irq(shost->host_lock);
-		vport->fc_flag &= ~(FC_FABRIC | FC_PUBLIC_LOOP);
+		vport->fc_flag &= ~(FC_FABRIC | FC_PUBLIC_LOOP |
+				    FC_PT2PT_NO_NVME);
 		spin_unlock_irq(shost->host_lock);
 
 		/* If private loop, then allow max outstanding els to be
@@ -1122,12 +1124,12 @@
 	/* FLOGI completes successfully */
 	lpfc_printf_vlog(vport, KERN_INFO, LOG_ELS,
 			 "0101 FLOGI completes successfully, I/O tag:x%x, "
-			 "xri x%x Data: x%x x%x x%x x%x x%x x%x x%x\n",
+			 "xri x%x Data: x%x x%x x%x x%x x%x x%x x%x %d\n",
 			 cmdiocb->iotag, cmdiocb->sli4_xritag,
 			 irsp->un.ulpWord[4], sp->cmn.e_d_tov,
 			 sp->cmn.w2.r_a_tov, sp->cmn.edtovResolution,
 			 vport->port_state, vport->fc_flag,
-			 sp->cmn.priority_tagging);
+			 sp->cmn.priority_tagging, kref_read(&ndlp->kref));
 
 	if (sp->cmn.priority_tagging)
 		vport->vmid_flag |= LPFC_VMID_ISSUE_QFPA;
@@ -1205,8 +1207,6 @@
 	phba->fcf.fcf_flag &= ~FCF_DISCOVERY;
 	spin_unlock_irq(&phba->hbalock);
 
-	if (!(ndlp->fc4_xpt_flags & (SCSI_XPT_REGD | NVME_XPT_REGD)))
-		lpfc_nlp_put(ndlp);
 	if (!lpfc_error_lost_link(irsp)) {
 		/* FLOGI failed, so just use loop map to make discovery list */
 		lpfc_disc_list_loopmap(vport);
@@ -2330,6 +2330,13 @@
 			lpfc_disc_state_machine(vport, ndlp, cmdiocb,
 						NLP_EVT_CMPL_PRLI);
 
+		/*
+		 * For P2P topology, retain the node so that PLOGI can be
+		 * attempted on it again.
+		 */
+		if (vport->fc_flag & FC_PT2PT)
+			goto out;
+
 		/* As long as this node is not registered with the SCSI
 		 * or NVMe transport and no other PRLIs are outstanding,
 		 * it is no longer an active node.  Otherwise devloss
@@ -2899,9 +2906,9 @@
 	irsp = &(rspiocb->iocb);
 	spin_lock_irq(&ndlp->lock);
 	ndlp->nlp_flag &= ~NLP_LOGO_SND;
-	if (ndlp->upcall_flags & NLP_WAIT_FOR_LOGO) {
+	if (ndlp->save_flags & NLP_WAIT_FOR_LOGO) {
 		wake_up_waiter = 1;
-		ndlp->upcall_flags &= ~NLP_WAIT_FOR_LOGO;
+		ndlp->save_flags &= ~NLP_WAIT_FOR_LOGO;
 	}
 	spin_unlock_irq(&ndlp->lock);
 
@@ -2955,18 +2962,10 @@
 		spin_unlock_irq(&ndlp->lock);
 		lpfc_disc_state_machine(vport, ndlp, cmdiocb,
 					NLP_EVT_DEVICE_RM);
-		lpfc_els_free_iocb(phba, cmdiocb);
-		lpfc_nlp_put(ndlp);
-
-		/* Presume the node was released. */
-		return;
+		goto out_rsrc_free;
 	}
 
 out:
-	/* Driver is done with the IO.  */
-	lpfc_els_free_iocb(phba, cmdiocb);
-	lpfc_nlp_put(ndlp);
-
 	/* At this point, the LOGO processing is complete. NOTE: For a
 	 * pt2pt topology, we are assuming the NPortID will only change
 	 * on link up processing. For a LOGO / PLOGI initiated by the
@@ -2993,6 +2992,10 @@
 				 ndlp->nlp_DID, irsp->ulpStatus,
 				 irsp->un.ulpWord[4], irsp->ulpTimeout,
 				 vport->num_disc_nodes);
+
+		lpfc_els_free_iocb(phba, cmdiocb);
+		lpfc_nlp_put(ndlp);
+
 		lpfc_disc_start(vport);
 		return;
 	}
@@ -3009,6 +3012,10 @@
 		lpfc_disc_state_machine(vport, ndlp, cmdiocb,
 					NLP_EVT_DEVICE_RM);
 	}
+out_rsrc_free:
+	/* Driver is done with the I/O. */
+	lpfc_els_free_iocb(phba, cmdiocb);
+	lpfc_nlp_put(ndlp);
 }
 
 /**
@@ -3532,11 +3539,6 @@
 		return 1;
 	}
 
-	/* This will cause the callback-function lpfc_cmpl_els_cmd to
-	 * trigger the release of node.
-	 */
-	if (!(vport->fc_flag & FC_PT2PT))
-		lpfc_nlp_put(ndlp);
 	return 0;
 }
 
@@ -3782,9 +3784,6 @@
 {
 	u32 rsp_sig_cap = 0, drv_sig_cap = 0;
 	u32 rsp_sig_freq_cyc = 0, rsp_sig_freq_scale = 0;
-	struct lpfc_cgn_info *cp;
-	u32 crc;
-	u16 sig_freq;
 
 	/* Get rsp signal and frequency capabilities.  */
 	rsp_sig_cap = be32_to_cpu(pcgd->xmt_signal_capability);
@@ -3840,25 +3839,7 @@
 		}
 	}
 
-	if (!phba->cgn_i)
-		return;
-
-	/* Update signal frequency in congestion info buffer */
-	cp = (struct lpfc_cgn_info *)phba->cgn_i->virt;
-
-	/* Frequency (in ms) Signal Warning/Signal Congestion Notifications
-	 * are received by the HBA
-	 */
-	sig_freq = phba->cgn_sig_freq;
-
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ONLY)
-		cp->cgn_warn_freq = cpu_to_le16(sig_freq);
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM) {
-		cp->cgn_alarm_freq = cpu_to_le16(sig_freq);
-		cp->cgn_warn_freq = cpu_to_le16(sig_freq);
-	}
-	crc = lpfc_cgn_calc_crc32(cp, LPFC_CGN_INFO_SZ, LPFC_CGN_CRC32_SEED);
-	cp->cgn_info_crc = cpu_to_le32(crc);
+	/* We are NOT recording signal frequency in congestion info buffer */
 	return;
 
 out_no_support:
@@ -4571,6 +4552,19 @@
 			retry = 1;
 			delay = 100;
 			break;
+		case IOERR_SLI_ABORTED:
+			/* Retry ELS PLOGI command?
+			 * Possibly the rport just wasn't ready.
+			 */
+			if (cmd == ELS_CMD_PLOGI) {
+				/* No retry if state change */
+				if (ndlp &&
+				    ndlp->nlp_state != NLP_STE_PLOGI_ISSUE)
+					goto out_retry;
+				retry = 1;
+				maxretry = 2;
+			}
+			break;
 		}
 		break;
 
@@ -4593,6 +4587,23 @@
 		/* Added for Vendor specifc support
 		 * Just keep retrying for these Rsn / Exp codes
 		 */
+		if ((vport->fc_flag & FC_PT2PT) &&
+		    cmd == ELS_CMD_NVMEPRLI) {
+			switch (stat.un.b.lsRjtRsnCode) {
+			case LSRJT_UNABLE_TPC:
+			case LSRJT_INVALID_CMD:
+			case LSRJT_LOGICAL_ERR:
+			case LSRJT_CMD_UNSUPPORTED:
+				lpfc_printf_vlog(vport, KERN_WARNING, LOG_ELS,
+						 "0168 NVME PRLI LS_RJT "
+						 "reason %x port doesn't "
+						 "support NVME, disabling NVME\n",
+						 stat.un.b.lsRjtRsnCode);
+				retry = 0;
+				vport->fc_flag |= FC_PT2PT_NO_NVME;
+				goto out_retry;
+			}
+		}
 		switch (stat.un.b.lsRjtRsnCode) {
 		case LSRJT_UNABLE_TPC:
 			/* The driver has a VALID PLOGI but the rport has
@@ -5076,14 +5087,9 @@
 		/* NPort Recovery mode or node is just allocated */
 		if (!lpfc_nlp_not_used(ndlp)) {
 			/* A LOGO is completing and the node is in NPR state.
-			 * If this a fabric node that cleared its transport
-			 * registration, release the rpi.
+			 * Just unregister the RPI because the node is still
+			 * required.
 			 */
-			spin_lock_irq(&ndlp->lock);
-			ndlp->nlp_flag &= ~NLP_NPR_2B_DISC;
-			if (phba->sli_rev == LPFC_SLI_REV4)
-				ndlp->nlp_flag |= NLP_RELEASE_RPI;
-			spin_unlock_irq(&ndlp->lock);
 			lpfc_unreg_rpi(vport, ndlp);
 		} else {
 			/* Indicate the node has already released, should
@@ -5296,6 +5302,7 @@
 	 */
 	if (phba->sli_rev == LPFC_SLI_REV4 &&
 	    (vport && vport->port_type == LPFC_NPIV_PORT) &&
+	    !(ndlp->fc4_xpt_flags & SCSI_XPT_REGD) &&
 	    ndlp->nlp_flag & NLP_RELEASE_RPI) {
 		lpfc_sli4_free_rpi(phba, ndlp->nlp_rpi);
 		spin_lock_irq(&ndlp->lock);
@@ -5599,11 +5606,12 @@
 	}
 
 	/* The NPIV instance is rejecting this unsolicited ELS. Make sure the
-	 * node's assigned RPI needs to be released as this node will get
-	 * freed.
+	 * node's assigned RPI gets released provided this node is not already
+	 * registered with the transport.
 	 */
 	if (phba->sli_rev == LPFC_SLI_REV4 &&
-	    vport->port_type == LPFC_NPIV_PORT) {
+	    vport->port_type == LPFC_NPIV_PORT &&
+	    !(ndlp->fc4_xpt_flags & SCSI_XPT_REGD)) {
 		spin_lock_irq(&ndlp->lock);
 		ndlp->nlp_flag |= NLP_RELEASE_RPI;
 		spin_unlock_irq(&ndlp->lock);
@@ -6216,6 +6224,7 @@
 			 * from backend
 			 */
 			lpfc_nlp_unreg_node(vport, ndlp);
+			lpfc_unreg_rpi(vport, ndlp);
 			continue;
 		}
 
@@ -6882,6 +6891,7 @@
 lpfc_get_rdp_info(struct lpfc_hba *phba, struct lpfc_rdp_context *rdp_context)
 {
 	LPFC_MBOXQ_t *mbox = NULL;
+	struct lpfc_dmabuf *mp;
 	int rc;
 
 	mbox = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
@@ -6897,8 +6907,11 @@
 	mbox->mbox_cmpl = lpfc_mbx_cmpl_rdp_page_a0;
 	mbox->ctx_ndlp = (struct lpfc_rdp_context *)rdp_context;
 	rc = lpfc_sli_issue_mbox(phba, mbox, MBX_NOWAIT);
-	if (rc == MBX_NOT_FINISHED)
+	if (rc == MBX_NOT_FINISHED) {
+		mp = (struct lpfc_dmabuf *)mbox->ctx_buf;
+		lpfc_mbuf_free(phba, mp->virt, mp->phys);
 		goto issue_mbox_fail;
+	}
 
 	return 0;
 
@@ -9572,11 +9585,14 @@
 			/* Take action here for an Alarm event */
 			if (phba->cmf_active_mode != LPFC_CFG_OFF) {
 				if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_ALARM) {
-					/* Track of alarm cnt for cgn_info */
-					atomic_inc(&phba->cgn_fabric_alarm_cnt);
 					/* Track of alarm cnt for SYNC_WQE */
 					atomic_inc(&phba->cgn_sync_alarm_cnt);
 				}
+				/* Track alarm cnt for cgn_info regardless
+				 * of whether CMF is configured for Signals
+				 * or FPINs.
+				 */
+				atomic_inc(&phba->cgn_fabric_alarm_cnt);
 				goto cleanup;
 			}
 			break;
@@ -9584,11 +9600,14 @@
 			/* Take action here for a Warning event */
 			if (phba->cmf_active_mode != LPFC_CFG_OFF) {
 				if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_WARN) {
-					/* Track of warning cnt for cgn_info */
-					atomic_inc(&phba->cgn_fabric_warn_cnt);
 					/* Track of warning cnt for SYNC_WQE */
 					atomic_inc(&phba->cgn_sync_warn_cnt);
 				}
+				/* Track warning cnt and freq for cgn_info
+				 * regardless of whether CMF is configured for
+				 * Signals or FPINs.
+				 */
+				atomic_inc(&phba->cgn_fabric_warn_cnt);
 cleanup:
 				/* Save frequency in ms */
 				phba->cgn_fpin_frequency =
@@ -9597,14 +9616,10 @@
 				if (phba->cgn_i) {
 					cp = (struct lpfc_cgn_info *)
 						phba->cgn_i->virt;
-					if (phba->cgn_reg_fpin &
-						LPFC_CGN_FPIN_ALARM)
-						cp->cgn_alarm_freq =
-							cpu_to_le16(value);
-					if (phba->cgn_reg_fpin &
-						LPFC_CGN_FPIN_WARN)
-						cp->cgn_warn_freq =
-							cpu_to_le16(value);
+					cp->cgn_alarm_freq =
+						cpu_to_le16(value);
+					cp->cgn_warn_freq =
+						cpu_to_le16(value);
 					crc = lpfc_cgn_calc_crc32
 						(cp,
 						LPFC_CGN_INFO_SZ,
@@ -10713,6 +10728,9 @@
 				 irsp->ulpStatus, irsp->un.ulpWord[4]);
 		goto fdisc_failed;
 	}
+
+	lpfc_check_nlp_post_devloss(vport, ndlp);
+
 	spin_lock_irq(shost->host_lock);
 	vport->fc_flag &= ~FC_VPORT_CVL_RCVD;
 	vport->fc_flag &= ~FC_VPORT_LOGO_RCVD;
@@ -10954,10 +10972,19 @@
 		lpfc_can_disctmo(vport);
 	}
 
+	if (ndlp->save_flags & NLP_WAIT_FOR_LOGO) {
+		/* Wake up lpfc_vport_delete if waiting...*/
+		if (ndlp->logo_waitq)
+			wake_up(ndlp->logo_waitq);
+		spin_lock_irq(&ndlp->lock);
+		ndlp->nlp_flag &= ~(NLP_ISSUE_LOGO | NLP_LOGO_SND);
+		ndlp->save_flags &= ~NLP_WAIT_FOR_LOGO;
+		spin_unlock_irq(&ndlp->lock);
+	}
+
 	/* Safe to release resources now. */
 	lpfc_els_free_iocb(phba, cmdiocb);
 	lpfc_nlp_put(ndlp);
-	vport->unreg_vpi_cmpl = VPORT_ERROR;
 }
 
 /**
@@ -11385,6 +11412,7 @@
 {
 	struct lpfc_hba *phba = vport->phba;
 	struct lpfc_sglq *sglq_entry = NULL, *sglq_next = NULL;
+	struct lpfc_nodelist *ndlp = NULL;
 	unsigned long iflag = 0;
 
 	spin_lock_irqsave(&phba->sli4_hba.sgl_list_lock, iflag);
@@ -11392,7 +11420,20 @@
 			&phba->sli4_hba.lpfc_abts_els_sgl_list, list) {
 		if (sglq_entry->ndlp && sglq_entry->ndlp->vport == vport) {
 			lpfc_nlp_put(sglq_entry->ndlp);
+			ndlp = sglq_entry->ndlp;
 			sglq_entry->ndlp = NULL;
+
+			/* If the xri on the abts_els_sgl list is for the Fport
+			 * node and the vport is unloading, the xri aborted wcqe
+			 * likely isn't coming back.  Just release the sgl.
+			 */
+			if ((vport->load_flag & FC_UNLOADING) &&
+			    ndlp->nlp_DID == Fabric_DID) {
+				list_del(&sglq_entry->list);
+				sglq_entry->state = SGL_FREED;
+				list_add_tail(&sglq_entry->list,
+					&phba->sli4_hba.lpfc_els_sgl_list);
+			}
 		}
 	}
 	spin_unlock_irqrestore(&phba->sli4_hba.sgl_list_lock, iflag);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_hbadisc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_hbadisc.c
@@ -209,7 +209,12 @@
 
 	spin_lock_irqsave(&ndlp->lock, iflags);
 	ndlp->nlp_flag |= NLP_IN_DEV_LOSS;
-	ndlp->nlp_flag &= ~NLP_NPR_2B_DISC;
+
+	/* If there is a PLOGI in progress, and we are in a
+	 * NLP_NPR_2B_DISC state, don't turn off the flag.
+	 */
+	if (ndlp->nlp_state != NLP_STE_PLOGI_ISSUE)
+		ndlp->nlp_flag &= ~NLP_NPR_2B_DISC;
 
 	/*
 	 * The backend does not expect any more calls associated with this
@@ -341,6 +346,37 @@
 }
 
 /**
+ * lpfc_check_nlp_post_devloss - Check to restore ndlp refcnt after devloss
+ * @vport: Pointer to vport object.
+ * @ndlp: Pointer to remote node object.
+ *
+ * If NLP_IN_RECOV_POST_DEV_LOSS flag was set due to outstanding recovery of
+ * node during dev_loss_tmo processing, then this function restores the nlp_put
+ * kref decrement from lpfc_dev_loss_tmo_handler.
+ **/
+void
+lpfc_check_nlp_post_devloss(struct lpfc_vport *vport,
+			    struct lpfc_nodelist *ndlp)
+{
+	unsigned long iflags;
+
+	spin_lock_irqsave(&ndlp->lock, iflags);
+	if (ndlp->save_flags & NLP_IN_RECOV_POST_DEV_LOSS) {
+		ndlp->save_flags &= ~NLP_IN_RECOV_POST_DEV_LOSS;
+		spin_unlock_irqrestore(&ndlp->lock, iflags);
+		lpfc_nlp_get(ndlp);
+		lpfc_printf_vlog(vport, KERN_INFO, LOG_DISCOVERY | LOG_NODE,
+				 "8438 Devloss timeout reversed on DID x%x "
+				 "refcnt %d ndlp %p flag x%x "
+				 "port_state = x%x\n",
+				 ndlp->nlp_DID, kref_read(&ndlp->kref), ndlp,
+				 ndlp->nlp_flag, vport->port_state);
+		spin_lock_irqsave(&ndlp->lock, iflags);
+	}
+	spin_unlock_irqrestore(&ndlp->lock, iflags);
+}
+
+/**
  * lpfc_dev_loss_tmo_handler - Remote node devloss timeout handler
  * @ndlp: Pointer to remote node object.
  *
@@ -358,6 +394,8 @@
 	uint8_t *name;
 	int warn_on = 0;
 	int fcf_inuse = 0;
+	bool recovering = false;
+	struct fc_vport *fc_vport = NULL;
 	unsigned long iflags;
 
 	vport = ndlp->vport;
@@ -394,6 +432,64 @@
 
 	/* Fabric nodes are done. */
 	if (ndlp->nlp_type & NLP_FABRIC) {
+		spin_lock_irqsave(&ndlp->lock, iflags);
+		/* In massive vport configuration settings, it's possible
+		 * dev_loss_tmo fired during node recovery.  So, check if
+		 * fabric nodes are in discovery states outstanding.
+		 */
+		switch (ndlp->nlp_DID) {
+		case Fabric_DID:
+			fc_vport = vport->fc_vport;
+			if (fc_vport &&
+			    fc_vport->vport_state == FC_VPORT_INITIALIZING)
+				recovering = true;
+			break;
+		case Fabric_Cntl_DID:
+			if (ndlp->nlp_flag & NLP_REG_LOGIN_SEND)
+				recovering = true;
+			break;
+		case FDMI_DID:
+			fallthrough;
+		case NameServer_DID:
+			if (ndlp->nlp_state >= NLP_STE_PLOGI_ISSUE &&
+			    ndlp->nlp_state <= NLP_STE_REG_LOGIN_ISSUE)
+				recovering = true;
+			break;
+		}
+		spin_unlock_irqrestore(&ndlp->lock, iflags);
+
+		/* Mark an NLP_IN_RECOV_POST_DEV_LOSS flag to know if reversing
+		 * the following lpfc_nlp_put is necessary after fabric node is
+		 * recovered.
+		 */
+		if (recovering) {
+			lpfc_printf_vlog(vport, KERN_INFO,
+					 LOG_DISCOVERY | LOG_NODE,
+					 "8436 Devloss timeout marked on "
+					 "DID x%x refcnt %d ndlp %p "
+					 "flag x%x port_state = x%x\n",
+					 ndlp->nlp_DID, kref_read(&ndlp->kref),
+					 ndlp, ndlp->nlp_flag,
+					 vport->port_state);
+			spin_lock_irqsave(&ndlp->lock, iflags);
+			ndlp->save_flags |= NLP_IN_RECOV_POST_DEV_LOSS;
+			spin_unlock_irqrestore(&ndlp->lock, iflags);
+		} else if (ndlp->nlp_state == NLP_STE_UNMAPPED_NODE) {
+			/* Fabric node fully recovered before this dev_loss_tmo
+			 * queue work is processed.  Thus, ignore the
+			 * dev_loss_tmo event.
+			 */
+			lpfc_printf_vlog(vport, KERN_INFO,
+					 LOG_DISCOVERY | LOG_NODE,
+					 "8437 Devloss timeout ignored on "
+					 "DID x%x refcnt %d ndlp %p "
+					 "flag x%x port_state = x%x\n",
+					 ndlp->nlp_DID, kref_read(&ndlp->kref),
+					 ndlp, ndlp->nlp_flag,
+					 vport->port_state);
+			return fcf_inuse;
+		}
+
 		lpfc_nlp_put(ndlp);
 		return fcf_inuse;
 	}
@@ -423,6 +519,14 @@
 				 ndlp->nlp_state, ndlp->nlp_rpi);
 	}
 
+	/* If we are devloss, but we are in the process of rediscovering the
+	 * ndlp, don't issue a NLP_EVT_DEVICE_RM event.
+	 */
+	if (ndlp->nlp_state >= NLP_STE_PLOGI_ISSUE &&
+	    ndlp->nlp_state <= NLP_STE_PRLI_ISSUE) {
+		return fcf_inuse;
+	}
+
 	if (!(ndlp->fc4_xpt_flags & NVME_XPT_REGD))
 		lpfc_disc_state_machine(vport, ndlp, NULL, NLP_EVT_DEVICE_RM);
 
@@ -765,10 +869,16 @@
 	if (phba->pci_dev_grp == LPFC_PCI_DEV_OC)
 		lpfc_sli4_post_async_mbox(phba);
 
-	if (ha_copy & HA_ERATT)
+	if (ha_copy & HA_ERATT) {
 		/* Handle the error attention event */
 		lpfc_handle_eratt(phba);
 
+		if (phba->fw_dump_cmpl) {
+			complete(phba->fw_dump_cmpl);
+			phba->fw_dump_cmpl = NULL;
+		}
+	}
+
 	if (ha_copy & HA_MBATT)
 		lpfc_sli_handle_mb_event(phba);
 
@@ -966,8 +1076,20 @@
 	struct lpfc_nodelist *ndlp, *next_ndlp;
 
 	list_for_each_entry_safe(ndlp, next_ndlp, &vport->fc_nodes, nlp_listp) {
-		if (ndlp->nlp_state == NLP_STE_UNUSED_NODE)
+		if (ndlp->nlp_state == NLP_STE_UNUSED_NODE) {
+			/* It's possible the FLOGI to the fabric node never
+			 * successfully completed and never registered with the
+			 * transport.  In this case there is no way to clean up
+			 * the node.
+			 */
+			if (ndlp->nlp_DID == Fabric_DID) {
+				if (ndlp->nlp_prev_state ==
+				    NLP_STE_UNUSED_NODE &&
+				    !ndlp->fc4_xpt_flags)
+					lpfc_nlp_put(ndlp);
+			}
 			continue;
+		}
 
 		if ((phba->sli3_options & LPFC_SLI3_VPORT_TEARDOWN) ||
 		    ((vport->port_type == LPFC_NPIV_PORT) &&
@@ -3812,7 +3934,6 @@
 	vport->vpi_state &= ~LPFC_VPI_REGISTERED;
 	vport->fc_flag |= FC_VPORT_NEEDS_REG_VPI;
 	spin_unlock_irq(shost->host_lock);
-	vport->unreg_vpi_cmpl = VPORT_OK;
 	mempool_free(pmb, phba->mbox_mem_pool);
 	lpfc_cleanup_vports_rrqs(vport, NULL);
 	/*
@@ -3842,7 +3963,6 @@
 		lpfc_printf_vlog(vport, KERN_ERR, LOG_TRACE_EVENT,
 				 "1800 Could not issue unreg_vpi\n");
 		mempool_free(mbox, phba->mbox_mem_pool);
-		vport->unreg_vpi_cmpl = VPORT_ERROR;
 		return rc;
 	}
 	return 0;
@@ -4351,6 +4471,8 @@
 		goto out;
 	}
 
+	lpfc_check_nlp_post_devloss(vport, ndlp);
+
 	if (phba->sli_rev < LPFC_SLI_REV4)
 		ndlp->nlp_rpi = mb->un.varWords[0];
 
@@ -4360,6 +4482,7 @@
 			 ndlp->nlp_state);
 
 	ndlp->nlp_flag |= NLP_RPI_REGISTERED;
+	ndlp->nlp_flag &= ~NLP_REG_LOGIN_SEND;
 	ndlp->nlp_type |= NLP_FABRIC;
 	lpfc_nlp_set_state(vport, ndlp, NLP_STE_UNMAPPED_NODE);
 
@@ -4449,8 +4572,9 @@
 		fc_remote_port_rolechg(rport, rport_ids.roles);
 
 	lpfc_printf_vlog(ndlp->vport, KERN_INFO, LOG_NODE,
-			 "3183 %s rport x%px DID x%x, role x%x\n",
-			 __func__, rport, rport->port_id, rport->roles);
+			 "3183 %s rport x%px DID x%x, role x%x refcnt %d\n",
+			 __func__, rport, rport->port_id, rport->roles,
+			 kref_read(&ndlp->kref));
 
 	if ((rport->scsi_target_id != -1) &&
 	    (rport->scsi_target_id < LPFC_MAX_TARGET)) {
@@ -4475,8 +4599,9 @@
 
 	lpfc_printf_vlog(vport, KERN_INFO, LOG_NODE,
 			 "3184 rport unregister x%06x, rport x%px "
-			 "xptflg x%x\n",
-			 ndlp->nlp_DID, rport, ndlp->fc4_xpt_flags);
+			 "xptflg x%x refcnt %d\n",
+			 ndlp->nlp_DID, rport, ndlp->fc4_xpt_flags,
+			 kref_read(&ndlp->kref));
 
 	fc_remote_port_delete(rport);
 	lpfc_nlp_put(ndlp);
@@ -4525,9 +4650,10 @@
 void
 lpfc_nlp_reg_node(struct lpfc_vport *vport, struct lpfc_nodelist *ndlp)
 {
-
 	unsigned long iflags;
 
+	lpfc_check_nlp_post_devloss(vport, ndlp);
+
 	spin_lock_irqsave(&ndlp->lock, iflags);
 	if (ndlp->fc4_xpt_flags & NLP_XPT_REGD) {
 		/* Already registered with backend, trigger rescan */
@@ -4679,8 +4805,11 @@
 	/* Reg/Unreg for FCP and NVME Transport interface */
 	if ((old_state == NLP_STE_MAPPED_NODE ||
 	     old_state == NLP_STE_UNMAPPED_NODE)) {
-		/* For nodes marked for ADISC, Handle unreg in ADISC cmpl */
-		if (!(ndlp->nlp_flag & NLP_NPR_ADISC))
+		/* For nodes marked for ADISC, Handle unreg in ADISC cmpl
+		 * if linkup. In linkdown do unreg_node
+		 */
+		if (!(ndlp->nlp_flag & NLP_NPR_ADISC) ||
+		    !lpfc_is_link_up(vport->phba))
 			lpfc_nlp_unreg_node(vport, ndlp);
 	}
 
@@ -5233,6 +5362,7 @@
 
 			rc = lpfc_sli_issue_mbox(phba, mbox, MBX_NOWAIT);
 			if (rc == MBX_NOT_FINISHED) {
+				ndlp->nlp_flag &= ~NLP_UNREG_INP;
 				mempool_free(mbox, phba->mbox_mem_pool);
 				acc_plogi = 1;
 			}
@@ -6837,7 +6967,9 @@
 	if (rc)
 		return;
 	/* Reset HBA FCF states after successful unregister FCF */
+	spin_lock_irq(&phba->hbalock);
 	phba->fcf.fcf_flag = 0;
+	spin_unlock_irq(&phba->hbalock);
 	phba->fcf.current_rec.flag = 0;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_hw.h
@@ -3746,7 +3746,7 @@
 #define IOERR_ILLEGAL_COMMAND         0x06
 #define IOERR_XCHG_DROPPED            0x07
 #define IOERR_ILLEGAL_FIELD           0x08
-#define IOERR_BAD_CONTINUE            0x09
+#define IOERR_RPI_SUSPENDED           0x09
 #define IOERR_TOO_MANY_BUFFERS        0x0A
 #define IOERR_RCV_BUFFER_WAITING      0x0B
 #define IOERR_NO_CONNECTION           0x0C
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_hw4.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_hw4.h
@@ -4448,6 +4448,9 @@
 #define wqe_sup_SHIFT         6
 #define wqe_sup_MASK          0x00000001
 #define wqe_sup_WORD          word11
+#define wqe_ffrq_SHIFT         6
+#define wqe_ffrq_MASK          0x00000001
+#define wqe_ffrq_WORD          word11
 #define wqe_wqec_SHIFT        7
 #define wqe_wqec_MASK         0x00000001
 #define wqe_wqec_WORD         word11
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_init.c
@@ -662,6 +662,50 @@
 }
 
 /**
+ * lpfc_sli4_refresh_params - update driver copy of params.
+ * @phba: Pointer to HBA context object.
+ *
+ * This is called to refresh driver copy of dynamic fields from the
+ * common_get_sli4_parameters descriptor.
+ **/
+int
+lpfc_sli4_refresh_params(struct lpfc_hba *phba)
+{
+	LPFC_MBOXQ_t *mboxq;
+	struct lpfc_mqe *mqe;
+	struct lpfc_sli4_parameters *mbx_sli4_parameters;
+	int length, rc;
+
+	mboxq = (LPFC_MBOXQ_t *)mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
+	if (!mboxq)
+		return -ENOMEM;
+
+	mqe = &mboxq->u.mqe;
+	/* Read the port's SLI4 Config Parameters */
+	length = (sizeof(struct lpfc_mbx_get_sli4_parameters) -
+		  sizeof(struct lpfc_sli4_cfg_mhdr));
+	lpfc_sli4_config(phba, mboxq, LPFC_MBOX_SUBSYSTEM_COMMON,
+			 LPFC_MBOX_OPCODE_GET_SLI4_PARAMETERS,
+			 length, LPFC_SLI4_MBX_EMBED);
+
+	rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+	if (unlikely(rc)) {
+		mempool_free(mboxq, phba->mbox_mem_pool);
+		return rc;
+	}
+	mbx_sli4_parameters = &mqe->un.get_sli4_parameters.sli4_parameters;
+	phba->sli4_hba.pc_sli4_params.mi_ver =
+			bf_get(cfg_mi_ver, mbx_sli4_parameters);
+	phba->sli4_hba.pc_sli4_params.cmf =
+			bf_get(cfg_cmf, mbx_sli4_parameters);
+	phba->sli4_hba.pc_sli4_params.pls =
+			bf_get(cfg_pvl, mbx_sli4_parameters);
+
+	mempool_free(mboxq, phba->mbox_mem_pool);
+	return rc;
+}
+
+/**
  * lpfc_hba_init_link - Initialize the FC link
  * @phba: pointer to lpfc hba data structure.
  * @flag: mailbox command issue mode - either MBX_POLL or MBX_NOWAIT
@@ -1606,6 +1650,11 @@
 lpfc_sli4_offline_eratt(struct lpfc_hba *phba)
 {
 	spin_lock_irq(&phba->hbalock);
+	if (phba->link_state == LPFC_HBA_ERROR &&
+	    phba->hba_flag & HBA_PCI_ERR) {
+		spin_unlock_irq(&phba->hbalock);
+		return;
+	}
 	phba->link_state = LPFC_HBA_ERROR;
 	spin_unlock_irq(&phba->hbalock);
 
@@ -1945,7 +1994,6 @@
 	if (pci_channel_offline(phba->pcidev)) {
 		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
 				"3166 pci channel is offline\n");
-		lpfc_sli4_offline_eratt(phba);
 		return;
 	}
 
@@ -2055,7 +2103,7 @@
 		}
 		if (reg_err1 == SLIPORT_ERR1_REG_ERR_CODE_2 &&
 		    reg_err2 == SLIPORT_ERR2_REG_FW_RESTART) {
-			lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+			lpfc_printf_log(phba, KERN_ERR, LOG_SLI,
 					"3143 Port Down: Firmware Update "
 					"Detected\n");
 			en_rn_msg = false;
@@ -3643,6 +3691,7 @@
 	struct lpfc_vport **vports;
 	struct Scsi_Host *shost;
 	int i;
+	int offline = 0;
 
 	if (vport->fc_flag & FC_OFFLINE_MODE)
 		return;
@@ -3651,6 +3700,8 @@
 
 	lpfc_linkdown(phba);
 
+	offline =  pci_channel_offline(phba->pcidev);
+
 	/* Issue an unreg_login to all nodes on all vports */
 	vports = lpfc_create_vport_work_array(phba);
 	if (vports != NULL) {
@@ -3673,7 +3724,14 @@
 				ndlp->nlp_flag &= ~NLP_NPR_ADISC;
 				spin_unlock_irq(&ndlp->lock);
 
-				lpfc_unreg_rpi(vports[i], ndlp);
+				if (offline) {
+					spin_lock_irq(&ndlp->lock);
+					ndlp->nlp_flag &= ~(NLP_UNREG_INP |
+							    NLP_RPI_REGISTERED);
+					spin_unlock_irq(&ndlp->lock);
+				} else {
+					lpfc_unreg_rpi(vports[i], ndlp);
+				}
 				/*
 				 * Whenever an SLI4 port goes offline, free the
 				 * RPI. Get a new RPI when the adapter port
@@ -3694,12 +3752,16 @@
 					lpfc_disc_state_machine(vports[i], ndlp,
 						NULL, NLP_EVT_DEVICE_RECOVERY);
 
-					/* Don't remove the node unless the
+					/* Don't remove the node unless the node
 					 * has been unregistered with the
-					 * transport.  If so, let dev_loss
-					 * take care of the node.
+					 * transport, and we're not in recovery
+					 * before dev_loss_tmo triggered.
+					 * Otherwise, let dev_loss take care of
+					 * the node.
 					 */
-					if (!(ndlp->fc4_xpt_flags &
+					if (!(ndlp->save_flags &
+					      NLP_IN_RECOV_POST_DEV_LOSS) &&
+					    !(ndlp->fc4_xpt_flags &
 					      (NVME_XPT_REGD | SCSI_XPT_REGD)))
 						lpfc_disc_state_machine
 							(vports[i], ndlp,
@@ -4649,7 +4711,7 @@
 	rc = lpfc_vmid_res_alloc(phba, vport);
 
 	if (rc)
-		goto out;
+		goto out_put_shost;
 
 	/* Initialize all internally managed lists. */
 	INIT_LIST_HEAD(&vport->fc_nodes);
@@ -4667,16 +4729,17 @@
 
 	error = scsi_add_host_with_dma(shost, dev, &phba->pcidev->dev);
 	if (error)
-		goto out_put_shost;
+		goto out_free_vmid;
 
 	spin_lock_irq(&phba->port_list_lock);
 	list_add_tail(&vport->listentry, &phba->port_list);
 	spin_unlock_irq(&phba->port_list_lock);
 	return vport;
 
-out_put_shost:
+out_free_vmid:
 	kfree(vport->vmid);
 	bitmap_free(vport->vmid_priority_range);
+out_put_shost:
 	scsi_host_put(shost);
 out:
 	return NULL;
@@ -5310,8 +5373,10 @@
 	 */
 	if (!(phba->hba_flag & HBA_FCOE_MODE)) {
 		rc = lpfc_sli_issue_mbox(phba, pmb, MBX_NOWAIT);
-		if (rc == MBX_NOT_FINISHED)
+		if (rc == MBX_NOT_FINISHED) {
+			lpfc_mbuf_free(phba, mp->virt, mp->phys);
 			goto out_free_dmabuf;
+		}
 		return;
 	}
 	/*
@@ -5407,38 +5472,12 @@
 void
 lpfc_cgn_dump_rxmonitor(struct lpfc_hba *phba)
 {
-	struct rxtable_entry *entry;
-	int cnt = 0, head, tail, last, start;
-
-	head = atomic_read(&phba->rxtable_idx_head);
-	tail = atomic_read(&phba->rxtable_idx_tail);
-	if (!phba->rxtable || head == tail) {
-		lpfc_printf_log(phba, KERN_ERR, LOG_CGN_MGMT,
-				"4411 Rxtable is empty\n");
-		return;
-	}
-	last = tail;
-	start = head;
-
-	/* Display the last LPFC_MAX_RXMONITOR_DUMP entries from the rxtable */
-	while (start != last) {
-		if (start)
-			start--;
-		else
-			start = LPFC_MAX_RXMONITOR_ENTRY - 1;
-		entry = &phba->rxtable[start];
+	if (!phba->rx_monitor) {
 		lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT,
-				"4410 %02d: MBPI %lld Xmit %lld Cmpl %lld "
-				"Lat %lld ASz %lld Info %02d BWUtil %d "
-				"Int %d slot %d\n",
-				cnt, entry->max_bytes_per_interval,
-				entry->total_bytes, entry->rcv_bytes,
-				entry->avg_io_latency, entry->avg_io_size,
-				entry->cmf_info, entry->timer_utilization,
-				entry->timer_interval, start);
-		cnt++;
-		if (cnt >= LPFC_MAX_RXMONITOR_DUMP)
-			return;
+				"4411 Rx Monitor Info is empty.\n");
+	} else {
+		lpfc_rx_monitor_report(phba, phba->rx_monitor, NULL, 0,
+				       LPFC_MAX_RXMONITOR_DUMP);
 	}
 }
 
@@ -5789,21 +5828,8 @@
 
 	/* Use the frequency found in the last rcv'ed FPIN */
 	value = phba->cgn_fpin_frequency;
-	if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_WARN)
-		cp->cgn_warn_freq = cpu_to_le16(value);
-	if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_ALARM)
-		cp->cgn_alarm_freq = cpu_to_le16(value);
-
-	/* Frequency (in ms) Signal Warning/Signal Congestion Notifications
-	 * are received by the HBA
-	 */
-	value = phba->cgn_sig_freq;
-
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ONLY ||
-	    phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM)
-		cp->cgn_warn_freq = cpu_to_le16(value);
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM)
-		cp->cgn_alarm_freq = cpu_to_le16(value);
+	cp->cgn_warn_freq = cpu_to_le16(value);
+	cp->cgn_alarm_freq = cpu_to_le16(value);
 
 	lvalue = lpfc_cgn_calc_crc32(cp, LPFC_CGN_INFO_SZ,
 				     LPFC_CGN_CRC32_SEED);
@@ -5858,11 +5884,10 @@
 {
 	struct lpfc_hba *phba = container_of(timer, struct lpfc_hba,
 					     cmf_timer);
-	struct rxtable_entry *entry;
+	struct rx_info_entry entry;
 	uint32_t io_cnt;
-	uint32_t head, tail;
 	uint32_t busy, max_read;
-	uint64_t total, rcv, lat, mbpi;
+	uint64_t total, rcv, lat, mbpi, extra, cnt;
 	int timer_interval = LPFC_CMF_INTERVAL;
 	uint32_t ms;
 	struct lpfc_cgn_stat *cgs;
@@ -5929,12 +5954,32 @@
 	    phba->hba_flag & HBA_SETUP) {
 		mbpi = phba->cmf_last_sync_bw;
 		phba->cmf_last_sync_bw = 0;
-		lpfc_issue_cmf_sync_wqe(phba, LPFC_CMF_INTERVAL, total);
+		extra = 0;
+
+		/* Calculate any extra bytes needed to account for the
+		 * timer accuracy. If we are less than LPFC_CMF_INTERVAL
+		 * calculate the adjustment needed for total to reflect
+		 * a full LPFC_CMF_INTERVAL.
+		 */
+		if (ms && ms < LPFC_CMF_INTERVAL) {
+			cnt = div_u64(total, ms); /* bytes per ms */
+			cnt *= LPFC_CMF_INTERVAL; /* what total should be */
+
+			/* If the timeout is scheduled to be shorter,
+			 * this value may skew the data, so cap it at mbpi.
+			 */
+			if ((phba->hba_flag & HBA_SHORT_CMF) && cnt > mbpi)
+				cnt = mbpi;
+
+			extra = cnt - total;
+		}
+		lpfc_issue_cmf_sync_wqe(phba, LPFC_CMF_INTERVAL, total + extra);
 	} else {
 		/* For Monitor mode or link down we want mbpi
 		 * to be the full link speed
 		 */
 		mbpi = phba->cmf_link_byte_count;
+		extra = 0;
 	}
 	phba->cmf_timer_cnt++;
 
@@ -5960,39 +6005,30 @@
 	}
 
 	/* Save rxmonitor information for debug */
-	if (phba->rxtable) {
-		head = atomic_xchg(&phba->rxtable_idx_head,
-				   LPFC_RXMONITOR_TABLE_IN_USE);
-		entry = &phba->rxtable[head];
-		entry->total_bytes = total;
-		entry->rcv_bytes = rcv;
-		entry->cmf_busy = busy;
-		entry->cmf_info = phba->cmf_active_info;
+	if (phba->rx_monitor) {
+		entry.total_bytes = total;
+		entry.cmf_bytes = total + extra;
+		entry.rcv_bytes = rcv;
+		entry.cmf_busy = busy;
+		entry.cmf_info = phba->cmf_active_info;
 		if (io_cnt) {
-			entry->avg_io_latency = div_u64(lat, io_cnt);
-			entry->avg_io_size = div_u64(rcv, io_cnt);
+			entry.avg_io_latency = div_u64(lat, io_cnt);
+			entry.avg_io_size = div_u64(rcv, io_cnt);
 		} else {
-			entry->avg_io_latency = 0;
-			entry->avg_io_size = 0;
+			entry.avg_io_latency = 0;
+			entry.avg_io_size = 0;
 		}
-		entry->max_read_cnt = max_read;
-		entry->io_cnt = io_cnt;
-		entry->max_bytes_per_interval = mbpi;
+		entry.max_read_cnt = max_read;
+		entry.io_cnt = io_cnt;
+		entry.max_bytes_per_interval = mbpi;
 		if (phba->cmf_active_mode == LPFC_CFG_MANAGED)
-			entry->timer_utilization = phba->cmf_last_ts;
+			entry.timer_utilization = phba->cmf_last_ts;
 		else
-			entry->timer_utilization = ms;
-		entry->timer_interval = ms;
+			entry.timer_utilization = ms;
+		entry.timer_interval = ms;
 		phba->cmf_last_ts = 0;
 
-		/* Increment rxtable index */
-		head = (head + 1) % LPFC_MAX_RXMONITOR_ENTRY;
-		tail = atomic_read(&phba->rxtable_idx_tail);
-		if (head == tail) {
-			tail = (tail + 1) % LPFC_MAX_RXMONITOR_ENTRY;
-			atomic_set(&phba->rxtable_idx_tail, tail);
-		}
-		atomic_set(&phba->rxtable_idx_head, head);
+		lpfc_rx_monitor_record(phba->rx_monitor, &entry);
 	}
 
 	if (phba->cmf_active_mode == LPFC_CFG_MONITOR) {
@@ -6007,6 +6043,8 @@
 	/* Each minute save Fabric and Driver congestion information */
 	lpfc_cgn_save_evt_cnt(phba);
 
+	phba->hba_flag &= ~HBA_SHORT_CMF;
+
 	/* Since we need to call lpfc_cgn_save_evt_cnt every minute, on the
 	 * minute, adjust our next timer interval, if needed, to ensure a
 	 * 1 minute granularity when we get the next timer interrupt.
@@ -6017,6 +6055,8 @@
 						  jiffies);
 		if (timer_interval <= 0)
 			timer_interval = LPFC_CMF_INTERVAL;
+		else
+			phba->hba_flag |= HBA_SHORT_CMF;
 
 		/* If we adjust timer_interval, max_bytes_per_interval
 		 * needs to be adjusted as well.
@@ -6262,8 +6302,10 @@
 	}
 
 	rc = lpfc_sli_issue_mbox(phba, pmb, MBX_NOWAIT);
-	if (rc == MBX_NOT_FINISHED)
+	if (rc == MBX_NOT_FINISHED) {
+		lpfc_mbuf_free(phba, mp->virt, mp->phys);
 		goto out_free_dmabuf;
+	}
 	return;
 
 out_free_dmabuf:
@@ -6428,6 +6470,12 @@
 					"3194 Unable to retrieve supported "
 					"speeds, rc = 0x%x\n", rc);
 		}
+		rc = lpfc_sli4_refresh_params(phba);
+		if (rc) {
+			lpfc_printf_log(phba, KERN_ERR, LOG_SLI,
+					"3174 Unable to update pls support, "
+					"rc x%x\n", rc);
+		}
 		vports = lpfc_create_vport_work_array(phba);
 		if (vports != NULL) {
 			for (i = 0; i <= phba->max_vports && vports[i] != NULL;
@@ -6485,9 +6533,6 @@
 		/* Alarm overrides warning, so check that first */
 		if (cgn_signal->alarm_cnt) {
 			if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM) {
-				/* Keep track of alarm cnt for cgn_info */
-				atomic_add(cgn_signal->alarm_cnt,
-					   &phba->cgn_fabric_alarm_cnt);
 				/* Keep track of alarm cnt for CMF_SYNC_WQE */
 				atomic_add(cgn_signal->alarm_cnt,
 					   &phba->cgn_sync_alarm_cnt);
@@ -6496,8 +6541,6 @@
 			/* signal action needs to be taken */
 			if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ONLY ||
 			    phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM) {
-				/* Keep track of warning cnt for cgn_info */
-				atomic_add(cnt, &phba->cgn_fabric_warn_cnt);
 				/* Keep track of warning cnt for CMF_SYNC_WQE */
 				atomic_add(cnt, &phba->cgn_sync_warn_cnt);
 			}
@@ -7072,6 +7115,8 @@
 	/* Find out if the FW has a new set of congestion parameters. */
 	len = sizeof(struct lpfc_cgn_param);
 	pdata = kzalloc(len, GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
 	ret = lpfc_read_object(phba, (char *)LPFC_PORT_CFG_NAME,
 			       pdata, len);
 
@@ -7358,7 +7403,7 @@
 out_disable_device:
 	pci_disable_device(pdev);
 out_error:
-	lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+	lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 			"1401 Failed to enable pci device\n");
 	return -ENODEV;
 }
@@ -7890,7 +7935,7 @@
 	/* Allocate device driver memory */
 	rc = lpfc_mem_alloc(phba, SGL_ALIGN_SZ);
 	if (rc)
-		return -ENOMEM;
+		goto out_destroy_workqueue;
 
 	/* IF Type 2 ports get initialized now. */
 	if (bf_get(lpfc_sli_intf_if_type, &phba->sli4_hba.sli_intf) >=
@@ -8306,6 +8351,9 @@
 	lpfc_destroy_bootstrap_mbox(phba);
 out_free_mem:
 	lpfc_mem_free(phba);
+out_destroy_workqueue:
+	destroy_workqueue(phba->wq);
+	phba->wq = NULL;
 	return rc;
 }
 
@@ -8401,7 +8449,7 @@
 		phba->lpfc_stop_port = lpfc_stop_port_s4;
 		break;
 	default:
-		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 				"1431 Invalid HBA PCI-device group: 0x%x\n",
 				dev_grp);
 		return -ENODEV;
@@ -11623,7 +11671,7 @@
 	/* There is no SLI3 failback for SLI4 devices. */
 	if (bf_get(lpfc_sli_intf_valid, &phba->sli4_hba.sli_intf) !=
 	    LPFC_SLI_INTF_VALID) {
-		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 				"2894 SLI_INTF reg contents invalid "
 				"sli_intf reg 0x%x\n",
 				phba->sli4_hba.sli_intf.word0);
@@ -11749,7 +11797,7 @@
 				goto out_iounmap_all;
 		} else {
 			error = -ENOMEM;
-			goto out_iounmap_all;
+			goto out_iounmap_ctrl;
 		}
 	}
 
@@ -11767,7 +11815,7 @@
 			dev_err(&pdev->dev,
 			   "ioremap failed for SLI4 HBA dpp registers.\n");
 			error = -ENOMEM;
-			goto out_iounmap_ctrl;
+			goto out_iounmap_all;
 		}
 		phba->pci_bar4_memmap_p = phba->sli4_hba.dpp_regs_memmap_p;
 	}
@@ -11792,9 +11840,11 @@
 	return 0;
 
 out_iounmap_all:
-	iounmap(phba->sli4_hba.drbl_regs_memmap_p);
+	if (phba->sli4_hba.drbl_regs_memmap_p)
+		iounmap(phba->sli4_hba.drbl_regs_memmap_p);
 out_iounmap_ctrl:
-	iounmap(phba->sli4_hba.ctrl_regs_memmap_p);
+	if (phba->sli4_hba.ctrl_regs_memmap_p)
+		iounmap(phba->sli4_hba.ctrl_regs_memmap_p);
 out_iounmap_conf:
 	iounmap(phba->sli4_hba.conf_regs_memmap_p);
 
@@ -13368,8 +13418,6 @@
 	atomic_set(&phba->cgn_sync_alarm_cnt, 0);
 	atomic_set(&phba->cgn_sync_warn_cnt, 0);
 
-	atomic64_set(&phba->cgn_acqe_stat.alarm, 0);
-	atomic64_set(&phba->cgn_acqe_stat.warn, 0);
 	atomic_set(&phba->cgn_driver_evt_cnt, 0);
 	atomic_set(&phba->cgn_latency_evt_cnt, 0);
 	atomic64_set(&phba->cgn_latency_evt, 0);
@@ -14080,6 +14128,10 @@
 		return error;
 	}
 
+	/* Init cpu_map array */
+	lpfc_cpu_map_array_init(phba);
+	/* Init hba_eq_hdl array */
+	lpfc_hba_eq_hdl_array_init(phba);
 	/* Configure and enable interrupt */
 	intr_mode = lpfc_sli_enable_intr(phba, phba->intr_mode);
 	if (intr_mode == LPFC_INTR_ERROR) {
@@ -14521,7 +14573,7 @@
 int
 lpfc_sli4_request_firmware_update(struct lpfc_hba *phba, uint8_t fw_upgrade)
 {
-	uint8_t file_name[ELX_MODEL_NAME_SIZE];
+	char file_name[ELX_FW_NAME_SIZE] = {0};
 	int ret;
 	const struct firmware *fw;
 
@@ -14530,7 +14582,7 @@
 	    LPFC_SLI_INTF_IF_TYPE_2)
 		return -EPERM;
 
-	snprintf(file_name, ELX_MODEL_NAME_SIZE, "%s.grp", phba->ModelName);
+	scnprintf(file_name, sizeof(file_name), "%s.grp", phba->ModelName);
 
 	if (fw_upgrade == INT_FW_UPGRADE) {
 		ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_UEVENT,
@@ -15033,14 +15085,17 @@
 		lpfc_sli4_prep_dev_for_recover(phba);
 		return PCI_ERS_RESULT_CAN_RECOVER;
 	case pci_channel_io_frozen:
+		phba->hba_flag |= HBA_PCI_ERR;
 		/* Fatal error, prepare for slot reset */
 		lpfc_sli4_prep_dev_for_reset(phba);
 		return PCI_ERS_RESULT_NEED_RESET;
 	case pci_channel_io_perm_failure:
+		phba->hba_flag |= HBA_PCI_ERR;
 		/* Permanent failure, prepare for device down */
 		lpfc_sli4_prep_dev_for_perm_failure(phba);
 		return PCI_ERS_RESULT_DISCONNECT;
 	default:
+		phba->hba_flag |= HBA_PCI_ERR;
 		/* Unknown state, prepare and request slot reset */
 		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
 				"2825 Unknown PCI error state: x%x\n", state);
@@ -15084,6 +15139,7 @@
 
 	pci_restore_state(pdev);
 
+	phba->hba_flag &= ~HBA_PCI_ERR;
 	/*
 	 * As the new kernel behavior of pci_restore_state() API call clears
 	 * device saved_state flag, need to save the restored state again.
@@ -15097,6 +15153,8 @@
 	psli->sli_flag &= ~LPFC_SLI_ACTIVE;
 	spin_unlock_irq(&phba->hbalock);
 
+	/* Init cpu_map array */
+	lpfc_cpu_map_array_init(phba);
 	/* Configure and enable interrupt */
 	intr_mode = lpfc_sli4_enable_intr(phba, phba->intr_mode);
 	if (intr_mode == LPFC_INTR_ERROR) {
@@ -15106,6 +15164,7 @@
 		return PCI_ERS_RESULT_DISCONNECT;
 	} else
 		phba->intr_mode = intr_mode;
+	lpfc_cpu_affinity_check(phba, phba->cfg_irq_chann);
 
 	/* Log the current active interrupt mode */
 	lpfc_log_intr_mode(phba, phba->intr_mode);
@@ -15307,6 +15366,10 @@
 	struct lpfc_hba *phba = ((struct lpfc_vport *)shost->hostdata)->phba;
 	pci_ers_result_t rc = PCI_ERS_RESULT_DISCONNECT;
 
+	if (phba->link_state == LPFC_HBA_ERROR &&
+	    phba->hba_flag & HBA_IOQ_FLUSH)
+		return PCI_ERS_RESULT_NEED_RESET;
+
 	switch (phba->pci_dev_grp) {
 	case LPFC_PCI_DEV_LP:
 		rc = lpfc_io_error_detected_s3(pdev, state);
@@ -15554,34 +15617,7 @@
 	unsigned int temp_idx;
 	int i;
 	int j = 0;
-	unsigned long rem_nsec, iflags;
-	bool log_verbose = false;
-	struct lpfc_vport *port_iterator;
-
-	/* Don't dump messages if we explicitly set log_verbose for the
-	 * physical port or any vport.
-	 */
-	if (phba->cfg_log_verbose)
-		return;
-
-	spin_lock_irqsave(&phba->port_list_lock, iflags);
-	list_for_each_entry(port_iterator, &phba->port_list, listentry) {
-		if (port_iterator->load_flag & FC_UNLOADING)
-			continue;
-		if (scsi_host_get(lpfc_shost_from_vport(port_iterator))) {
-			if (port_iterator->cfg_log_verbose)
-				log_verbose = true;
-
-			scsi_host_put(lpfc_shost_from_vport(port_iterator));
-
-			if (log_verbose) {
-				spin_unlock_irqrestore(&phba->port_list_lock,
-						       iflags);
-				return;
-			}
-		}
-	}
-	spin_unlock_irqrestore(&phba->port_list_lock, iflags);
+	unsigned long rem_nsec;
 
 	if (atomic_cmpxchg(&phba->dbg_log_dmping, 0, 1) != 0)
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_logmsg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_logmsg.h
@@ -73,7 +73,7 @@
 #define lpfc_printf_vlog(vport, level, mask, fmt, arg...) \
 do { \
 	{ if (((mask) & (vport)->cfg_log_verbose) || (level[1] <= '3')) { \
-		if ((mask) & LOG_TRACE_EVENT) \
+		if ((mask) & LOG_TRACE_EVENT && !(vport)->cfg_log_verbose) \
 			lpfc_dmp_dbg((vport)->phba); \
 		dev_printk(level, &((vport)->phba->pcidev)->dev, "%d:(%d):" \
 			   fmt, (vport)->phba->brd_no, vport->vpi, ##arg);  \
@@ -89,11 +89,11 @@
 				 (phba)->pport->cfg_log_verbose : \
 				 (phba)->cfg_log_verbose; \
 	if (((mask) & log_verbose) || (level[1] <= '3')) { \
-		if ((mask) & LOG_TRACE_EVENT) \
+		if ((mask) & LOG_TRACE_EVENT && !log_verbose) \
 			lpfc_dmp_dbg(phba); \
 		dev_printk(level, &((phba)->pcidev)->dev, "%d:" \
 			fmt, phba->brd_no, ##arg); \
-	} else  if (!(phba)->cfg_log_verbose)\
+	} else if (!log_verbose)\
 		lpfc_dbg_print(phba, "%d:" fmt, phba->brd_no, ##arg); \
 	} \
 } while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_mem.c
@@ -344,9 +344,12 @@
 		phba->cgn_i = NULL;
 	}
 
-	/* Free RX table */
-	kfree(phba->rxtable);
-	phba->rxtable = NULL;
+	/* Free RX Monitor */
+	if (phba->rx_monitor) {
+		lpfc_rx_monitor_destroy_ring(phba->rx_monitor);
+		kfree(phba->rx_monitor);
+		phba->rx_monitor = NULL;
+	}
 
 	/* Free the iocb lookup array */
 	kfree(psli->iocbq_lookup);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_nportdisc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_nportdisc.c
@@ -322,6 +322,7 @@
 {
 	struct lpfc_hba    *phba = vport->phba;
 	struct lpfc_dmabuf *pcmd;
+	struct lpfc_dmabuf *mp;
 	uint64_t nlp_portwwn = 0;
 	uint32_t *lp;
 	IOCB_t *icmd;
@@ -571,6 +572,11 @@
 		 * a default RPI.
 		 */
 		if (phba->sli_rev == LPFC_SLI_REV4) {
+			mp = (struct lpfc_dmabuf *)login_mbox->ctx_buf;
+			if (mp) {
+				lpfc_mbuf_free(phba, mp->virt, mp->phys);
+				kfree(mp);
+			}
 			mempool_free(login_mbox, phba->mbox_mem_pool);
 			login_mbox = NULL;
 		} else {
@@ -718,8 +724,10 @@
 				/* Save the ELS cmd */
 				elsiocb->drvrTimeout = cmd;
 
-				lpfc_sli4_resume_rpi(ndlp,
-					lpfc_mbx_cmpl_resume_rpi, elsiocb);
+				if (lpfc_sli4_resume_rpi(ndlp,
+						lpfc_mbx_cmpl_resume_rpi,
+						elsiocb))
+					kfree(elsiocb);
 				goto out;
 			}
 		}
@@ -804,7 +812,8 @@
 		lpfc_nvmet_invalidate_host(phba, ndlp);
 
 	if (ndlp->nlp_DID == Fabric_DID) {
-		if (vport->port_state <= LPFC_FDISC)
+		if (vport->port_state <= LPFC_FDISC ||
+		    vport->fc_flag & FC_PT2PT)
 			goto out;
 		lpfc_linkdown_port(vport);
 		spin_lock_irq(shost->host_lock);
@@ -1955,8 +1964,9 @@
 			 * is configured try it.
 			 */
 			ndlp->nlp_fc4_type |= NLP_FC4_FCP;
-			if ((vport->cfg_enable_fc4_type == LPFC_ENABLE_BOTH) ||
-			    (vport->cfg_enable_fc4_type == LPFC_ENABLE_NVME)) {
+			if ((!(vport->fc_flag & FC_PT2PT_NO_NVME)) &&
+			    (vport->cfg_enable_fc4_type == LPFC_ENABLE_BOTH ||
+			    vport->cfg_enable_fc4_type == LPFC_ENABLE_NVME)) {
 				ndlp->nlp_fc4_type |= NLP_FC4_NVME;
 				/* We need to update the localport also */
 				lpfc_nvme_update_localport(vport);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_nvme.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_nvme.c
@@ -209,8 +209,9 @@
 	 * calling state machine to remove the node.
 	 */
 	lpfc_printf_vlog(vport, KERN_INFO, LOG_NVME_DISC,
-			"6146 remoteport delete of remoteport x%px\n",
-			remoteport);
+			 "6146 remoteport delete of remoteport x%px, ndlp x%px "
+			 "DID x%x xflags x%x\n",
+			 remoteport, ndlp, ndlp->nlp_DID, ndlp->fc4_xpt_flags);
 	spin_lock_irq(&ndlp->lock);
 
 	/* The register rebind might have occurred before the delete
@@ -936,6 +937,7 @@
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	int cpu;
 #endif
+	int offline = 0;
 
 	/* Sanity check on return of outstanding command */
 	if (!lpfc_ncmd) {
@@ -1097,11 +1099,12 @@
 			nCmd->transferred_length = 0;
 			nCmd->rcv_rsplen = 0;
 			nCmd->status = NVME_SC_INTERNAL;
+			offline = pci_channel_offline(vport->phba->pcidev);
 		}
 	}
 
 	/* pick up SLI4 exhange busy condition */
-	if (bf_get(lpfc_wcqe_c_xb, wcqe))
+	if (bf_get(lpfc_wcqe_c_xb, wcqe) && !offline)
 		lpfc_ncmd->flags |= LPFC_SBUF_XBUSY;
 	else
 		lpfc_ncmd->flags &= ~LPFC_SBUF_XBUSY;
@@ -1181,7 +1184,8 @@
 {
 	struct lpfc_hba *phba = vport->phba;
 	struct nvmefc_fcp_req *nCmd = lpfc_ncmd->nvmeCmd;
-	struct lpfc_iocbq *pwqeq = &(lpfc_ncmd->cur_iocbq);
+	struct nvme_common_command *sqe;
+	struct lpfc_iocbq *pwqeq = &lpfc_ncmd->cur_iocbq;
 	union lpfc_wqe128 *wqe = &pwqeq->wqe;
 	uint32_t req_len;
 
@@ -1238,8 +1242,14 @@
 		cstat->control_requests++;
 	}
 
-	if (pnode->nlp_nvme_info & NLP_NVME_NSLER)
+	if (pnode->nlp_nvme_info & NLP_NVME_NSLER) {
 		bf_set(wqe_erp, &wqe->generic.wqe_com, 1);
+		sqe = &((struct nvme_fc_cmd_iu *)
+			nCmd->cmdaddr)->sqe.common;
+		if (sqe->opcode == nvme_admin_async_event)
+			bf_set(wqe_ffrq, &wqe->generic.wqe_com, 1);
+	}
+
 	/*
 	 * Finish initializing those WQE fields that are independent
 	 * of the nvme_cmnd request_buffer
@@ -1296,7 +1306,6 @@
 	struct sli4_sge *first_data_sgl;
 	struct ulp_bde64 *bde;
 	dma_addr_t physaddr = 0;
-	uint32_t num_bde = 0;
 	uint32_t dma_len = 0;
 	uint32_t dma_offset = 0;
 	int nseg, i, j;
@@ -1350,7 +1359,7 @@
 			}
 
 			sgl->word2 = 0;
-			if ((num_bde + 1) == nseg) {
+			if (nseg == 1) {
 				bf_set(lpfc_sli4_sge_last, sgl, 1);
 				bf_set(lpfc_sli4_sge_type, sgl,
 				       LPFC_SGE_TYPE_DATA);
@@ -1419,8 +1428,9 @@
 
 			j++;
 		}
-		if (phba->cfg_enable_pbde) {
-			/* Use PBDE support for first SGL only, offset == 0 */
+
+		/* PBDE support for first data SGE only */
+		if (nseg == 1 && phba->cfg_enable_pbde) {
 			/* Words 13-15 */
 			bde = (struct ulp_bde64 *)
 				&wqe->words[13];
@@ -1431,11 +1441,11 @@
 			bde->tus.f.bdeFlags = BUFF_TYPE_BDE_64;
 			bde->tus.w = cpu_to_le32(bde->tus.w);
 
-			/* Word 11 */
+			/* Word 11 - set PBDE bit */
 			bf_set(wqe_pbde, &wqe->generic.wqe_com, 1);
 		} else {
 			memset(&wqe->words[13], 0, (sizeof(uint32_t) * 3));
-			bf_set(wqe_pbde, &wqe->generic.wqe_com, 0);
+			/* Word 11 - PBDE bit disabled by default template */
 		}
 
 	} else {
@@ -2166,6 +2176,10 @@
 			abts_nvme = 0;
 			for (i = 0; i < phba->cfg_hdw_queue; i++) {
 				qp = &phba->sli4_hba.hdwq[i];
+				if (!vport || !vport->localport ||
+				    !qp || !qp->io_wq)
+					return;
+
 				pring = qp->io_wq->pring;
 				if (!pring)
 					continue;
@@ -2173,6 +2187,10 @@
 				abts_scsi += qp->abts_scsi_io_bufs;
 				abts_nvme += qp->abts_nvme_io_bufs;
 			}
+			if (!vport || !vport->localport ||
+			    vport->phba->hba_flag & HBA_PCI_ERR)
+				return;
+
 			lpfc_printf_vlog(vport, KERN_ERR, LOG_TRACE_EVENT,
 					 "6176 Lport x%px Localport x%px wait "
 					 "timed out. Pending %d [%d:%d]. "
@@ -2212,6 +2230,8 @@
 		return;
 
 	localport = vport->localport;
+	if (!localport)
+		return;
 	lport = (struct lpfc_nvme_lport *)localport->private;
 
 	lpfc_printf_vlog(vport, KERN_INFO, LOG_NVME,
@@ -2519,16 +2539,17 @@
 		/* No concern about the role change on the nvme remoteport.
 		 * The transport will update it.
 		 */
-		spin_lock_irq(&vport->phba->hbalock);
+		spin_lock_irq(&ndlp->lock);
 		ndlp->fc4_xpt_flags |= NVME_XPT_UNREG_WAIT;
-		spin_unlock_irq(&vport->phba->hbalock);
+		spin_unlock_irq(&ndlp->lock);
 
 		/* Don't let the host nvme transport keep sending keep-alives
 		 * on this remoteport. Vport is unloading, no recovery. The
 		 * return values is ignored.  The upcall is a courtesy to the
 		 * transport.
 		 */
-		if (vport->load_flag & FC_UNLOADING)
+		if (vport->load_flag & FC_UNLOADING ||
+		    unlikely(vport->phba->hba_flag & HBA_PCI_ERR))
 			(void)nvme_fc_set_remoteport_devloss(remoteport, 0);
 
 		ret = nvme_fc_unregister_remoteport(remoteport);
@@ -2557,6 +2578,42 @@
 }
 
 /**
+ * lpfc_sli4_nvme_pci_offline_aborted - Fast-path process of NVME xri abort
+ * @phba: pointer to lpfc hba data structure.
+ * @lpfc_ncmd: The nvme job structure for the request being aborted.
+ *
+ * This routine is invoked by the worker thread to process a SLI4 fast-path
+ * NVME aborted xri.  Aborted NVME IO commands are completed to the transport
+ * here.
+ **/
+void
+lpfc_sli4_nvme_pci_offline_aborted(struct lpfc_hba *phba,
+				   struct lpfc_io_buf *lpfc_ncmd)
+{
+	struct nvmefc_fcp_req *nvme_cmd = NULL;
+
+	lpfc_printf_log(phba, KERN_INFO, LOG_NVME_ABTS,
+			"6533 %s nvme_cmd %p tag x%x abort complete and "
+			"xri released\n", __func__,
+			lpfc_ncmd->nvmeCmd,
+			lpfc_ncmd->cur_iocbq.iotag);
+
+	/* Aborted NVME commands are required to not complete
+	 * before the abort exchange command fully completes.
+	 * Once completed, it is available via the put list.
+	 */
+	if (lpfc_ncmd->nvmeCmd) {
+		nvme_cmd = lpfc_ncmd->nvmeCmd;
+		nvme_cmd->transferred_length = 0;
+		nvme_cmd->rcv_rsplen = 0;
+		nvme_cmd->status = NVME_SC_INTERNAL;
+		nvme_cmd->done(nvme_cmd);
+		lpfc_ncmd->nvmeCmd = NULL;
+	}
+	lpfc_release_nvme_buf(phba, lpfc_ncmd);
+}
+
+/**
  * lpfc_sli4_nvme_xri_aborted - Fast-path process of NVME xri abort
  * @phba: pointer to lpfc hba data structure.
  * @axri: pointer to the fcp xri abort wcqe structure.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_nvmet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_nvmet.c
@@ -1586,7 +1586,7 @@
 		wqe = &nvmewqe->wqe;
 
 		/* Initialize WQE */
-		memset(wqe, 0, sizeof(union lpfc_wqe));
+		memset(wqe, 0, sizeof(*wqe));
 
 		ctx_buf->iocbq->context1 = NULL;
 		spin_lock(&phba->sli4_hba.sgl_list_lock);
@@ -2708,7 +2708,7 @@
 	struct ulp_bde64 *bde;
 	dma_addr_t physaddr;
 	int i, cnt, nsegs;
-	int do_pbde;
+	bool use_pbde = false;
 	int xc = 1;
 
 	if (!lpfc_is_link_up(phba)) {
@@ -2816,9 +2816,6 @@
 		if (!xc)
 			bf_set(wqe_xc, &wqe->fcp_tsend.wqe_com, 0);
 
-		/* Word 11 - set sup, irsp, irsplen later */
-		do_pbde = 0;
-
 		/* Word 12 */
 		wqe->fcp_tsend.fcp_data_len = rsp->transfer_length;
 
@@ -2896,12 +2893,13 @@
 		if (!xc)
 			bf_set(wqe_xc, &wqe->fcp_treceive.wqe_com, 0);
 
-		/* Word 11 - set pbde later */
-		if (phba->cfg_enable_pbde) {
-			do_pbde = 1;
+		/* Word 11 - check for pbde */
+		if (nsegs == 1 && phba->cfg_enable_pbde) {
+			use_pbde = true;
+			/* Word 11 - PBDE bit already preset by template */
 		} else {
+			/* Overwrite default template setting */
 			bf_set(wqe_pbde, &wqe->fcp_treceive.wqe_com, 0);
-			do_pbde = 0;
 		}
 
 		/* Word 12 */
@@ -2972,7 +2970,6 @@
 			       ((rsp->rsplen >> 2) - 1));
 			memcpy(&wqe->words[16], rsp->rspaddr, rsp->rsplen);
 		}
-		do_pbde = 0;
 
 		/* Word 12 */
 		wqe->fcp_trsp.rsvd_12_15[0] = 0;
@@ -3007,23 +3004,24 @@
 			bf_set(lpfc_sli4_sge_last, sgl, 1);
 		sgl->word2 = cpu_to_le32(sgl->word2);
 		sgl->sge_len = cpu_to_le32(cnt);
-		if (i == 0) {
-			bde = (struct ulp_bde64 *)&wqe->words[13];
-			if (do_pbde) {
-				/* Words 13-15  (PBDE) */
-				bde->addrLow = sgl->addr_lo;
-				bde->addrHigh = sgl->addr_hi;
-				bde->tus.f.bdeSize =
-					le32_to_cpu(sgl->sge_len);
-				bde->tus.f.bdeFlags = BUFF_TYPE_BDE_64;
-				bde->tus.w = cpu_to_le32(bde->tus.w);
-			} else {
-				memset(bde, 0, sizeof(struct ulp_bde64));
-			}
-		}
 		sgl++;
 		ctxp->offset += cnt;
 	}
+
+	bde = (struct ulp_bde64 *)&wqe->words[13];
+	if (use_pbde) {
+		/* decrement sgl ptr backwards once to first data sge */
+		sgl--;
+
+		/* Words 13-15 (PBDE) */
+		bde->addrLow = sgl->addr_lo;
+		bde->addrHigh = sgl->addr_hi;
+		bde->tus.f.bdeSize = le32_to_cpu(sgl->sge_len);
+		bde->tus.f.bdeFlags = BUFF_TYPE_BDE_64;
+		bde->tus.w = cpu_to_le32(bde->tus.w);
+	} else {
+		memset(bde, 0, sizeof(struct ulp_bde64));
+	}
 	ctxp->state = LPFC_NVME_STE_DATA;
 	ctxp->entry_cnt++;
 	return nvmewqe;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_scsi.c
@@ -117,8 +117,6 @@
 	}
 }
 
-#define LPFC_INVALID_REFTAG ((u32)-1)
-
 /**
  * lpfc_update_stats - Update statistical data for the command completion
  * @vport: The virtual port on which this call is executing.
@@ -233,11 +231,10 @@
 	struct Scsi_Host  *shost;
 	struct scsi_device *sdev;
 	unsigned long new_queue_depth;
-	unsigned long num_rsrc_err, num_cmd_success;
+	unsigned long num_rsrc_err;
 	int i;
 
 	num_rsrc_err = atomic_read(&phba->num_rsrc_err);
-	num_cmd_success = atomic_read(&phba->num_cmd_success);
 
 	/*
 	 * The error and success command counters are global per
@@ -252,20 +249,16 @@
 		for (i = 0; i <= phba->max_vports && vports[i] != NULL; i++) {
 			shost = lpfc_shost_from_vport(vports[i]);
 			shost_for_each_device(sdev, shost) {
-				new_queue_depth =
-					sdev->queue_depth * num_rsrc_err /
-					(num_rsrc_err + num_cmd_success);
-				if (!new_queue_depth)
-					new_queue_depth = sdev->queue_depth - 1;
+				if (num_rsrc_err >= sdev->queue_depth)
+					new_queue_depth = 1;
 				else
 					new_queue_depth = sdev->queue_depth -
-								new_queue_depth;
+						num_rsrc_err;
 				scsi_change_queue_depth(sdev, new_queue_depth);
 			}
 		}
 	lpfc_destroy_vport_work_array(phba, vports);
 	atomic_set(&phba->num_rsrc_err, 0);
-	atomic_set(&phba->num_cmd_success, 0);
 }
 
 /**
@@ -493,8 +486,8 @@
 lpfc_sli4_io_xri_aborted(struct lpfc_hba *phba,
 			 struct sli4_wcqe_xri_aborted *axri, int idx)
 {
-	uint16_t xri = bf_get(lpfc_wcqe_xa_xri, axri);
-	uint16_t rxid = bf_get(lpfc_wcqe_xa_remote_xid, axri);
+	u16 xri = 0;
+	u16 rxid = 0;
 	struct lpfc_io_buf *psb, *next_psb;
 	struct lpfc_sli4_hdw_queue *qp;
 	unsigned long iflag = 0;
@@ -504,15 +497,22 @@
 	int rrq_empty = 0;
 	struct lpfc_sli_ring *pring = phba->sli4_hba.els_wq->pring;
 	struct scsi_cmnd *cmd;
+	int offline = 0;
 
 	if (!(phba->cfg_enable_fc4_type & LPFC_ENABLE_FCP))
 		return;
-
+	offline = pci_channel_offline(phba->pcidev);
+	if (!offline) {
+		xri = bf_get(lpfc_wcqe_xa_xri, axri);
+		rxid = bf_get(lpfc_wcqe_xa_remote_xid, axri);
+	}
 	qp = &phba->sli4_hba.hdwq[idx];
 	spin_lock_irqsave(&phba->hbalock, iflag);
 	spin_lock(&qp->abts_io_buf_list_lock);
 	list_for_each_entry_safe(psb, next_psb,
 		&qp->lpfc_abts_io_buf_list, list) {
+		if (offline)
+			xri = psb->cur_iocbq.sli4_xritag;
 		if (psb->cur_iocbq.sli4_xritag == xri) {
 			list_del_init(&psb->list);
 			psb->flags &= ~LPFC_SBUF_XBUSY;
@@ -521,8 +521,15 @@
 				qp->abts_nvme_io_bufs--;
 				spin_unlock(&qp->abts_io_buf_list_lock);
 				spin_unlock_irqrestore(&phba->hbalock, iflag);
-				lpfc_sli4_nvme_xri_aborted(phba, axri, psb);
-				return;
+				if (!offline) {
+					lpfc_sli4_nvme_xri_aborted(phba, axri,
+								   psb);
+					return;
+				}
+				lpfc_sli4_nvme_pci_offline_aborted(phba, psb);
+				spin_lock_irqsave(&phba->hbalock, iflag);
+				spin_lock(&qp->abts_io_buf_list_lock);
+				continue;
 			}
 			qp->abts_scsi_io_bufs--;
 			spin_unlock(&qp->abts_io_buf_list_lock);
@@ -534,13 +541,13 @@
 
 			rrq_empty = list_empty(&phba->active_rrq_list);
 			spin_unlock_irqrestore(&phba->hbalock, iflag);
-			if (ndlp) {
+			if (ndlp && !offline) {
 				lpfc_set_rrq_active(phba, ndlp,
 					psb->cur_iocbq.sli4_lxritag, rxid, 1);
 				lpfc_sli4_abts_err_handler(phba, ndlp, axri);
 			}
 
-			if (phba->cfg_fcp_wait_abts_rsp) {
+			if (phba->cfg_fcp_wait_abts_rsp || offline) {
 				spin_lock_irqsave(&psb->buf_lock, iflag);
 				cmd = psb->pCmd;
 				psb->pCmd = NULL;
@@ -567,25 +574,30 @@
 			lpfc_release_scsi_buf_s4(phba, psb);
 			if (rrq_empty)
 				lpfc_worker_wake_up(phba);
-			return;
+			if (!offline)
+				return;
+			spin_lock_irqsave(&phba->hbalock, iflag);
+			spin_lock(&qp->abts_io_buf_list_lock);
+			continue;
 		}
 	}
 	spin_unlock(&qp->abts_io_buf_list_lock);
-	for (i = 1; i <= phba->sli.last_iotag; i++) {
-		iocbq = phba->sli.iocbq_lookup[i];
-
-		if (!(iocbq->iocb_flag & LPFC_IO_FCP) ||
-		    (iocbq->iocb_flag & LPFC_IO_LIBDFC))
-			continue;
-		if (iocbq->sli4_xritag != xri)
-			continue;
-		psb = container_of(iocbq, struct lpfc_io_buf, cur_iocbq);
-		psb->flags &= ~LPFC_SBUF_XBUSY;
-		spin_unlock_irqrestore(&phba->hbalock, iflag);
-		if (!list_empty(&pring->txq))
-			lpfc_worker_wake_up(phba);
-		return;
+	if (!offline) {
+		for (i = 1; i <= phba->sli.last_iotag; i++) {
+			iocbq = phba->sli.iocbq_lookup[i];
 
+			if (!(iocbq->iocb_flag & LPFC_IO_FCP) ||
+			    (iocbq->iocb_flag & LPFC_IO_LIBDFC))
+				continue;
+			if (iocbq->sli4_xritag != xri)
+				continue;
+			psb = container_of(iocbq, struct lpfc_io_buf, cur_iocbq);
+			psb->flags &= ~LPFC_SBUF_XBUSY;
+			spin_unlock_irqrestore(&phba->hbalock, iflag);
+			if (!list_empty(&pring->txq))
+				lpfc_worker_wake_up(phba);
+			return;
+		}
 	}
 	spin_unlock_irqrestore(&phba->hbalock, iflag);
 }
@@ -1023,8 +1035,6 @@
 
 	sgpe = scsi_prot_sglist(sc);
 	lba = scsi_prot_ref_tag(sc);
-	if (lba == LPFC_INVALID_REFTAG)
-		return 0;
 
 	/* First check if we need to match the LBA */
 	if (phba->lpfc_injerr_lba != LPFC_INJERR_LBA_OFF) {
@@ -1605,8 +1615,6 @@
 
 	/* extract some info from the scsi command for pde*/
 	reftag = scsi_prot_ref_tag(sc);
-	if (reftag == LPFC_INVALID_REFTAG)
-		goto out;
 
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	rc = lpfc_bg_err_inject(phba, sc, &reftag, NULL, 1);
@@ -1768,8 +1776,6 @@
 	/* extract some info from the scsi command */
 	blksize = scsi_prot_interval(sc);
 	reftag = scsi_prot_ref_tag(sc);
-	if (reftag == LPFC_INVALID_REFTAG)
-		goto out;
 
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	rc = lpfc_bg_err_inject(phba, sc, &reftag, NULL, 1);
@@ -1972,7 +1978,7 @@
  *
  * Returns the number of SGEs added to the SGL.
  **/
-static int
+static uint32_t
 lpfc_bg_setup_sgl(struct lpfc_hba *phba, struct scsi_cmnd *sc,
 		struct sli4_sge *sgl, int datasegcnt,
 		struct lpfc_io_buf *lpfc_cmd)
@@ -1980,8 +1986,8 @@
 	struct scatterlist *sgde = NULL; /* s/g data entry */
 	struct sli4_sge_diseed *diseed = NULL;
 	dma_addr_t physaddr;
-	int i = 0, num_sge = 0, status;
-	uint32_t reftag;
+	int i = 0, status;
+	uint32_t reftag, num_sge = 0;
 	uint8_t txop, rxop;
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	uint32_t rc;
@@ -1999,8 +2005,6 @@
 
 	/* extract some info from the scsi command for pde*/
 	reftag = scsi_prot_ref_tag(sc);
-	if (reftag == LPFC_INVALID_REFTAG)
-		goto out;
 
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	rc = lpfc_bg_err_inject(phba, sc, &reftag, NULL, 1);
@@ -2155,7 +2159,7 @@
  *
  * Returns the number of SGEs added to the SGL.
  **/
-static int
+static uint32_t
 lpfc_bg_setup_sgl_prot(struct lpfc_hba *phba, struct scsi_cmnd *sc,
 		struct sli4_sge *sgl, int datacnt, int protcnt,
 		struct lpfc_io_buf *lpfc_cmd)
@@ -2179,8 +2183,8 @@
 	uint32_t rc;
 #endif
 	uint32_t checking = 1;
-	uint32_t dma_offset = 0;
-	int num_sge = 0, j = 2;
+	uint32_t dma_offset = 0, num_sge = 0;
+	int j = 2;
 	struct sli4_hybrid_sgl *sgl_xtra = NULL;
 
 	sgpe = scsi_prot_sglist(sc);
@@ -2200,8 +2204,6 @@
 	/* extract some info from the scsi command */
 	blksize = scsi_prot_interval(sc);
 	reftag = scsi_prot_ref_tag(sc);
-	if (reftag == LPFC_INVALID_REFTAG)
-		goto out;
 
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	rc = lpfc_bg_err_inject(phba, sc, &reftag, NULL, 1);
@@ -2793,8 +2795,6 @@
 
 		src = (struct scsi_dif_tuple *)sg_virt(sgpe);
 		start_ref_tag = scsi_prot_ref_tag(cmd);
-		if (start_ref_tag == LPFC_INVALID_REFTAG)
-			goto out;
 		start_app_tag = src->app_tag;
 		len = sgpe->length;
 		while (src && protsegcnt) {
@@ -3215,7 +3215,6 @@
 	struct lpfc_vport *vport = phba->pport;
 	union lpfc_wqe128 *wqe = &pwqeq->wqe;
 	dma_addr_t physaddr;
-	uint32_t num_bde = 0;
 	uint32_t dma_len;
 	uint32_t dma_offset = 0;
 	int nseg, i, j;
@@ -3277,7 +3276,7 @@
 		j = 2;
 		for (i = 0; i < nseg; i++) {
 			sgl->word2 = 0;
-			if ((num_bde + 1) == nseg) {
+			if (nseg == 1) {
 				bf_set(lpfc_sli4_sge_last, sgl, 1);
 				bf_set(lpfc_sli4_sge_type, sgl,
 				       LPFC_SGE_TYPE_DATA);
@@ -3346,13 +3345,15 @@
 
 			j++;
 		}
-		/*
-		 * Setup the first Payload BDE. For FCoE we just key off
-		 * Performance Hints, for FC we use lpfc_enable_pbde.
-		 * We populate words 13-15 of IOCB/WQE.
+
+		/* PBDE support for first data SGE only.
+		 * For FCoE, we key off Performance Hints.
+		 * For FC, we key off lpfc_enable_pbde.
 		 */
-		if ((phba->sli3_options & LPFC_SLI4_PERFH_ENABLED) ||
-		    phba->cfg_enable_pbde) {
+		if (nseg == 1 &&
+		    ((phba->sli3_options & LPFC_SLI4_PERFH_ENABLED) ||
+		     phba->cfg_enable_pbde)) {
+			/* Words 13-15 */
 			bde = (struct ulp_bde64 *)
 				&wqe->words[13];
 			bde->addrLow = first_data_sgl->addr_lo;
@@ -3362,12 +3363,15 @@
 			bde->tus.f.bdeFlags = BUFF_TYPE_BDE_64;
 			bde->tus.w = cpu_to_le32(bde->tus.w);
 
+			/* Word 11 - set PBDE bit */
+			bf_set(wqe_pbde, &wqe->generic.wqe_com, 1);
 		} else {
 			memset(&wqe->words[13], 0, (sizeof(uint32_t) * 3));
+			/* Word 11 - PBDE bit disabled by default template */
 		}
 	} else {
 		sgl += 1;
-		/* clear the last flag in the fcp_rsp map entry */
+		/* set the last flag in the fcp_rsp map entry */
 		sgl->word2 = le32_to_cpu(sgl->word2);
 		bf_set(lpfc_sli4_sge_last, sgl, 1);
 		sgl->word2 = cpu_to_le32(sgl->word2);
@@ -3380,10 +3384,6 @@
 		}
 	}
 
-	/* Word 11 */
-	if (phba->cfg_enable_pbde)
-		bf_set(wqe_pbde, &wqe->generic.wqe_com, 1);
-
 	/*
 	 * Finish initializing those IOCB fields that are dependent on the
 	 * scsi_cmnd request_buffer.  Note that for SLI-2 the bdeSize is
@@ -3641,11 +3641,11 @@
 			     scsi_cmnd->sc_data_direction);
 
 	lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
-			"9084 Cannot setup S/G List for HBA"
-			"IO segs %d/%d SGL %d SCSI %d: %d %d\n",
+			"9084 Cannot setup S/G List for HBA "
+			"IO segs %d/%d SGL %d SCSI %d: %d %d %d\n",
 			lpfc_cmd->seg_cnt, lpfc_cmd->prot_seg_cnt,
 			phba->cfg_total_seg_cnt, phba->cfg_sg_seg_cnt,
-			prot_group_type, num_sge);
+			prot_group_type, num_sge, ret);
 
 	lpfc_cmd->seg_cnt = 0;
 	lpfc_cmd->prot_seg_cnt = 0;
@@ -3917,7 +3917,7 @@
 		else
 			time = div_u64(time + 500, 1000); /* round it */
 
-		cgs = this_cpu_ptr(phba->cmf_stat);
+		cgs = per_cpu_ptr(phba->cmf_stat, raw_smp_processor_id());
 		atomic64_add(size, &cgs->rcv_bytes);
 		atomic64_add(time, &cgs->rx_latency);
 		atomic_inc(&cgs->rx_io_cnt);
@@ -3941,7 +3941,8 @@
 	int cpu;
 
 	/* At this point we are either LPFC_CFG_MANAGED or LPFC_CFG_MONITOR */
-	if (phba->cmf_active_mode == LPFC_CFG_MANAGED) {
+	if (phba->cmf_active_mode == LPFC_CFG_MANAGED &&
+	    phba->cmf_max_bytes_per_interval) {
 		total = 0;
 		for_each_present_cpu(cpu) {
 			cgs = per_cpu_ptr(phba->cmf_stat, cpu);
@@ -3960,7 +3961,7 @@
 			atomic_set(&phba->rx_max_read_cnt, size);
 	}
 
-	cgs = this_cpu_ptr(phba->cmf_stat);
+	cgs = per_cpu_ptr(phba->cmf_stat, raw_smp_processor_id());
 	atomic64_add(size, &cgs->total_bytes);
 	return 0;
 }
@@ -4373,8 +4374,9 @@
 		if (lpfc_cmd->result == IOERR_INVALID_RPI ||
 		    lpfc_cmd->result == IOERR_NO_RESOURCES ||
 		    lpfc_cmd->result == IOERR_ABORT_REQUESTED ||
+		    lpfc_cmd->result == IOERR_RPI_SUSPENDED ||
 		    lpfc_cmd->result == IOERR_SLER_CMD_RCV_FAILURE) {
-			cmd->result = DID_REQUEUE << 16;
+			cmd->result = DID_TRANSPORT_DISRUPTED << 16;
 			break;
 		}
 		if ((lpfc_cmd->result == IOERR_RX_DMA_FAILED ||
@@ -4428,10 +4430,11 @@
 
 		lpfc_printf_vlog(vport, KERN_INFO, LOG_FCP,
 				 "9039 Iodone <%d/%llu> cmd x%px, error "
-				 "x%x SNS x%x x%x Data: x%x x%x\n",
+				 "x%x SNS x%x x%x LBA x%llx Data: x%x x%x\n",
 				 cmd->device->id, cmd->device->lun, cmd,
-				 cmd->result, *lp, *(lp + 3), cmd->retries,
-				 scsi_get_resid(cmd));
+				 cmd->result, *lp, *(lp + 3),
+				 (u64)scsi_get_lba(cmd),
+				 cmd->retries, scsi_get_resid(cmd));
 	}
 
 	lpfc_update_stats(vport, lpfc_cmd);
@@ -4661,7 +4664,7 @@
 			    lpfc_cmd->result == IOERR_NO_RESOURCES ||
 			    lpfc_cmd->result == IOERR_ABORT_REQUESTED ||
 			    lpfc_cmd->result == IOERR_SLER_CMD_RCV_FAILURE) {
-				cmd->result = DID_REQUEUE << 16;
+				cmd->result = DID_TRANSPORT_DISRUPTED << 16;
 				break;
 			}
 			if ((lpfc_cmd->result == IOERR_RX_DMA_FAILED ||
@@ -5095,7 +5098,7 @@
 		phba->lpfc_scsi_prep_cmnd_buf = lpfc_scsi_prep_cmnd_buf_s4;
 		break;
 	default:
-		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 				"1418 Invalid HBA PCI-device group: 0x%x\n",
 				dev_grp);
 		return -ENODEV;
@@ -5732,7 +5735,6 @@
 		}
 	}
 
-	atomic_inc(&ndlp->cmd_pending);
 #ifdef CONFIG_SCSI_LPFC_DEBUG_FS
 	if (unlikely(phba->hdwqstat_on & LPFC_CHECK_SCSI_IO))
 		this_cpu_inc(phba->sli4_hba.c_stat->xmt_io);
@@ -5885,25 +5887,25 @@
 	if (!lpfc_cmd)
 		return ret;
 
-	spin_lock_irqsave(&phba->hbalock, flags);
+	/* Guard against IO completion being called at same time */
+	spin_lock_irqsave(&lpfc_cmd->buf_lock, flags);
+
+	spin_lock(&phba->hbalock);
 	/* driver queued commands are in process of being flushed */
 	if (phba->hba_flag & HBA_IOQ_FLUSH) {
 		lpfc_printf_vlog(vport, KERN_WARNING, LOG_FCP,
 			"3168 SCSI Layer abort requested I/O has been "
 			"flushed by LLD.\n");
 		ret = FAILED;
-		goto out_unlock;
+		goto out_unlock_hba;
 	}
 
-	/* Guard against IO completion being called at same time */
-	spin_lock(&lpfc_cmd->buf_lock);
-
 	if (!lpfc_cmd->pCmd) {
 		lpfc_printf_vlog(vport, KERN_WARNING, LOG_FCP,
 			 "2873 SCSI Layer I/O Abort Request IO CMPL Status "
 			 "x%x ID %d LUN %llu\n",
 			 SUCCESS, cmnd->device->id, cmnd->device->lun);
-		goto out_unlock_buf;
+		goto out_unlock_hba;
 	}
 
 	iocb = &lpfc_cmd->cur_iocbq;
@@ -5911,7 +5913,7 @@
 		pring_s4 = phba->sli4_hba.hdwq[iocb->hba_wqidx].io_wq->pring;
 		if (!pring_s4) {
 			ret = FAILED;
-			goto out_unlock_buf;
+			goto out_unlock_hba;
 		}
 		spin_lock(&pring_s4->ring_lock);
 	}
@@ -5944,8 +5946,8 @@
 			 "3389 SCSI Layer I/O Abort Request is pending\n");
 		if (phba->sli_rev == LPFC_SLI_REV4)
 			spin_unlock(&pring_s4->ring_lock);
-		spin_unlock(&lpfc_cmd->buf_lock);
-		spin_unlock_irqrestore(&phba->hbalock, flags);
+		spin_unlock(&phba->hbalock);
+		spin_unlock_irqrestore(&lpfc_cmd->buf_lock, flags);
 		goto wait_for_cmpl;
 	}
 
@@ -5966,15 +5968,13 @@
 	if (ret_val != IOCB_SUCCESS) {
 		/* Indicate the IO is not being aborted by the driver. */
 		lpfc_cmd->waitq = NULL;
-		spin_unlock(&lpfc_cmd->buf_lock);
-		spin_unlock_irqrestore(&phba->hbalock, flags);
 		ret = FAILED;
-		goto out;
+		goto out_unlock_hba;
 	}
 
 	/* no longer need the lock after this point */
-	spin_unlock(&lpfc_cmd->buf_lock);
-	spin_unlock_irqrestore(&phba->hbalock, flags);
+	spin_unlock(&phba->hbalock);
+	spin_unlock_irqrestore(&lpfc_cmd->buf_lock, flags);
 
 	if (phba->cfg_poll & DISABLE_FCP_RING_INT)
 		lpfc_sli_handle_fast_ring_event(phba,
@@ -6009,10 +6009,9 @@
 out_unlock_ring:
 	if (phba->sli_rev == LPFC_SLI_REV4)
 		spin_unlock(&pring_s4->ring_lock);
-out_unlock_buf:
-	spin_unlock(&lpfc_cmd->buf_lock);
-out_unlock:
-	spin_unlock_irqrestore(&phba->hbalock, flags);
+out_unlock_hba:
+	spin_unlock(&phba->hbalock);
+	spin_unlock_irqrestore(&lpfc_cmd->buf_lock, flags);
 out:
 	lpfc_printf_vlog(vport, KERN_WARNING, LOG_FCP,
 			 "0749 SCSI Layer I/O Abort Request Status x%x ID %d "
@@ -6455,28 +6454,28 @@
 
 		/* Issue LOGO, if no LOGO is outstanding */
 		spin_lock_irqsave(&pnode->lock, flags);
-		if (!(pnode->upcall_flags & NLP_WAIT_FOR_LOGO) &&
+		if (!(pnode->save_flags & NLP_WAIT_FOR_LOGO) &&
 		    !pnode->logo_waitq) {
 			pnode->logo_waitq = &waitq;
 			pnode->nlp_fcp_info &= ~NLP_FCP_2_DEVICE;
 			pnode->nlp_flag |= NLP_ISSUE_LOGO;
-			pnode->upcall_flags |= NLP_WAIT_FOR_LOGO;
+			pnode->save_flags |= NLP_WAIT_FOR_LOGO;
 			spin_unlock_irqrestore(&pnode->lock, flags);
 			lpfc_unreg_rpi(vport, pnode);
 			wait_event_timeout(waitq,
-					   (!(pnode->upcall_flags &
+					   (!(pnode->save_flags &
 					      NLP_WAIT_FOR_LOGO)),
 					   msecs_to_jiffies(dev_loss_tmo *
 							    1000));
 
-			if (pnode->upcall_flags & NLP_WAIT_FOR_LOGO) {
+			if (pnode->save_flags & NLP_WAIT_FOR_LOGO) {
 				lpfc_printf_vlog(vport, KERN_ERR, logit,
 						 "0725 SCSI layer TGTRST "
 						 "failed & LOGO TMO (%d, %llu) "
 						 "return x%x\n",
 						 tgt_id, lun_id, status);
 				spin_lock_irqsave(&pnode->lock, flags);
-				pnode->upcall_flags &= ~NLP_WAIT_FOR_LOGO;
+				pnode->save_flags &= ~NLP_WAIT_FOR_LOGO;
 			} else {
 				spin_lock_irqsave(&pnode->lock, flags);
 			}
@@ -6628,6 +6627,13 @@
 	if (rc)
 		goto error;
 
+	/* Wait for successful restart of adapter */
+	if (phba->sli_rev < LPFC_SLI_REV4) {
+		rc = lpfc_sli_chipset_init(phba);
+		if (rc)
+			goto error;
+	}
+
 	rc = lpfc_online(phba);
 	if (rc)
 		goto error;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_sli.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_sli.c
@@ -1404,7 +1404,8 @@
 		}
 
 		if ((iocbq->iocb_flag & LPFC_EXCHANGE_BUSY) &&
-			(sglq->state != SGL_XRI_ABORTED)) {
+		    (!(unlikely(pci_channel_offline(phba->pcidev)))) &&
+		    sglq->state != SGL_XRI_ABORTED) {
 			spin_lock_irqsave(&phba->sli4_hba.sgl_list_lock,
 					  iflag);
 
@@ -2007,10 +2008,12 @@
 
 	sync_buf->iocb_flag |= LPFC_IO_CMF;
 	ret_val = lpfc_sli4_issue_wqe(phba, &phba->sli4_hba.hdwq[0], sync_buf);
-	if (ret_val)
+	if (ret_val) {
 		lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT,
 				"6214 Cannot issue CMF_SYNC_WQE: x%x\n",
 				ret_val);
+		__lpfc_sli_release_iocbq(phba, sync_buf);
+	}
 out_unlock:
 	spin_unlock_irqrestore(&phba->hbalock, iflags);
 	return ret_val;
@@ -4583,10 +4586,12 @@
 			lpfc_sli_cancel_iocbs(phba, &txq,
 					      IOSTAT_LOCAL_REJECT,
 					      IOERR_SLI_DOWN);
-			/* Flush the txcmpq */
+			/* Flush the txcmplq */
 			lpfc_sli_cancel_iocbs(phba, &txcmplq,
 					      IOSTAT_LOCAL_REJECT,
 					      IOERR_SLI_DOWN);
+			if (unlikely(pci_channel_offline(phba->pcidev)))
+				lpfc_sli4_io_xri_aborted(phba, NULL, 0);
 		}
 	} else {
 		pring = &psli->sli3_ring[LPFC_FCP_RING];
@@ -5043,12 +5048,6 @@
 	phba->fcf.fcf_flag = 0;
 	spin_unlock_irq(&phba->hbalock);
 
-	/* SLI4 INTF 2: if FW dump is being taken skip INIT_PORT */
-	if (phba->hba_flag & HBA_FW_DUMP_OP) {
-		phba->hba_flag &= ~HBA_FW_DUMP_OP;
-		return rc;
-	}
-
 	/* Now physically reset the device */
 	lpfc_printf_log(phba, KERN_INFO, LOG_INIT,
 			"0389 Performing PCI function reset!\n");
@@ -7491,7 +7490,7 @@
 	struct lpfc_sglq *sglq_entry = NULL;
 	struct lpfc_sglq *sglq_entry_next = NULL;
 	struct lpfc_sglq *sglq_entry_first = NULL;
-	int status, total_cnt;
+	int status = 0, total_cnt;
 	int post_cnt = 0, num_posted = 0, block_cnt = 0;
 	int last_xritag = NO_XRI;
 	LIST_HEAD(prep_sgl_list);
@@ -7761,8 +7760,6 @@
 
 	/* Zero out Congestion Signal ACQE counter */
 	phba->cgn_acqe_cnt = 0;
-	atomic64_set(&phba->cgn_acqe_stat.warn, 0);
-	atomic64_set(&phba->cgn_acqe_stat.alarm, 0);
 
 	acqe = bf_get(lpfc_mbx_set_feature_CGN_acqe_freq,
 		      &pmb->u.mqe.un.set_feature);
@@ -7880,6 +7877,172 @@
 }
 
 /**
+ * lpfc_rx_monitor_create_ring - Initialize ring buffer for rx_monitor
+ * @rx_monitor: Pointer to lpfc_rx_info_monitor object
+ * @entries: Number of rx_info_entry objects to allocate in ring
+ *
+ * Return:
+ * 0 - Success
+ * ENOMEM - Failure to kmalloc
+ **/
+int lpfc_rx_monitor_create_ring(struct lpfc_rx_info_monitor *rx_monitor,
+				u32 entries)
+{
+	rx_monitor->ring = kmalloc_array(entries, sizeof(struct rx_info_entry),
+					 GFP_KERNEL);
+	if (!rx_monitor->ring)
+		return -ENOMEM;
+
+	rx_monitor->head_idx = 0;
+	rx_monitor->tail_idx = 0;
+	spin_lock_init(&rx_monitor->lock);
+	rx_monitor->entries = entries;
+
+	return 0;
+}
+
+/**
+ * lpfc_rx_monitor_destroy_ring - Free ring buffer for rx_monitor
+ * @rx_monitor: Pointer to lpfc_rx_info_monitor object
+ **/
+void lpfc_rx_monitor_destroy_ring(struct lpfc_rx_info_monitor *rx_monitor)
+{
+	spin_lock(&rx_monitor->lock);
+	kfree(rx_monitor->ring);
+	rx_monitor->ring = NULL;
+	rx_monitor->entries = 0;
+	rx_monitor->head_idx = 0;
+	rx_monitor->tail_idx = 0;
+	spin_unlock(&rx_monitor->lock);
+}
+
+/**
+ * lpfc_rx_monitor_record - Insert an entry into rx_monitor's ring
+ * @rx_monitor: Pointer to lpfc_rx_info_monitor object
+ * @entry: Pointer to rx_info_entry
+ *
+ * Used to insert an rx_info_entry into rx_monitor's ring.  Note that this is a
+ * deep copy of rx_info_entry not a shallow copy of the rx_info_entry ptr.
+ *
+ * This is called from lpfc_cmf_timer, which is in timer/softirq context.
+ *
+ * In cases of old data overflow, we do a best effort of FIFO order.
+ **/
+void lpfc_rx_monitor_record(struct lpfc_rx_info_monitor *rx_monitor,
+			    struct rx_info_entry *entry)
+{
+	struct rx_info_entry *ring = rx_monitor->ring;
+	u32 *head_idx = &rx_monitor->head_idx;
+	u32 *tail_idx = &rx_monitor->tail_idx;
+	spinlock_t *ring_lock = &rx_monitor->lock;
+	u32 ring_size = rx_monitor->entries;
+
+	spin_lock(ring_lock);
+	memcpy(&ring[*tail_idx], entry, sizeof(*entry));
+	*tail_idx = (*tail_idx + 1) % ring_size;
+
+	/* Best effort of FIFO saved data */
+	if (*tail_idx == *head_idx)
+		*head_idx = (*head_idx + 1) % ring_size;
+
+	spin_unlock(ring_lock);
+}
+
+/**
+ * lpfc_rx_monitor_report - Read out rx_monitor's ring
+ * @phba: Pointer to lpfc_hba object
+ * @rx_monitor: Pointer to lpfc_rx_info_monitor object
+ * @buf: Pointer to char buffer that will contain rx monitor info data
+ * @buf_len: Length buf including null char
+ * @max_read_entries: Maximum number of entries to read out of ring
+ *
+ * Used to dump/read what's in rx_monitor's ring buffer.
+ *
+ * If buf is NULL || buf_len == 0, then it is implied that we want to log the
+ * information to kmsg instead of filling out buf.
+ *
+ * Return:
+ * Number of entries read out of the ring
+ **/
+u32 lpfc_rx_monitor_report(struct lpfc_hba *phba,
+			   struct lpfc_rx_info_monitor *rx_monitor, char *buf,
+			   u32 buf_len, u32 max_read_entries)
+{
+	struct rx_info_entry *ring = rx_monitor->ring;
+	struct rx_info_entry *entry;
+	u32 *head_idx = &rx_monitor->head_idx;
+	u32 *tail_idx = &rx_monitor->tail_idx;
+	spinlock_t *ring_lock = &rx_monitor->lock;
+	u32 ring_size = rx_monitor->entries;
+	u32 cnt = 0;
+	char tmp[DBG_LOG_STR_SZ] = {0};
+	bool log_to_kmsg = (!buf || !buf_len) ? true : false;
+
+	if (!log_to_kmsg) {
+		/* clear the buffer to be sure */
+		memset(buf, 0, buf_len);
+
+		scnprintf(buf, buf_len, "\t%-16s%-16s%-16s%-16s%-8s%-8s%-8s"
+					"%-8s%-8s%-8s%-16s\n",
+					"MaxBPI", "Tot_Data_CMF",
+					"Tot_Data_Cmd", "Tot_Data_Cmpl",
+					"Lat(us)", "Avg_IO", "Max_IO", "Bsy",
+					"IO_cnt", "Info", "BWutil(ms)");
+	}
+
+	/* Needs to be _irq because record is called from timer interrupt
+	 * context
+	 */
+	spin_lock_irq(ring_lock);
+	while (*head_idx != *tail_idx) {
+		entry = &ring[*head_idx];
+
+		/* Read out this entry's data. */
+		if (!log_to_kmsg) {
+			/* If !log_to_kmsg, then store to buf. */
+			scnprintf(tmp, sizeof(tmp),
+				  "%03d:\t%-16llu%-16llu%-16llu%-16llu%-8llu"
+				  "%-8llu%-8llu%-8u%-8u%-8u%u(%u)\n",
+				  *head_idx, entry->max_bytes_per_interval,
+				  entry->cmf_bytes, entry->total_bytes,
+				  entry->rcv_bytes, entry->avg_io_latency,
+				  entry->avg_io_size, entry->max_read_cnt,
+				  entry->cmf_busy, entry->io_cnt,
+				  entry->cmf_info, entry->timer_utilization,
+				  entry->timer_interval);
+
+			/* Check for buffer overflow */
+			if ((strlen(buf) + strlen(tmp)) >= buf_len)
+				break;
+
+			/* Append entry's data to buffer */
+			strlcat(buf, tmp, buf_len);
+		} else {
+			lpfc_printf_log(phba, KERN_INFO, LOG_CGN_MGMT,
+					"4410 %02u: MBPI %llu Xmit %llu "
+					"Cmpl %llu Lat %llu ASz %llu Info %02u "
+					"BWUtil %u Int %u slot %u\n",
+					cnt, entry->max_bytes_per_interval,
+					entry->total_bytes, entry->rcv_bytes,
+					entry->avg_io_latency,
+					entry->avg_io_size, entry->cmf_info,
+					entry->timer_utilization,
+					entry->timer_interval, *head_idx);
+		}
+
+		*head_idx = (*head_idx + 1) % ring_size;
+
+		/* Don't feed more than max_read_entries */
+		cnt++;
+		if (cnt >= max_read_entries)
+			break;
+	}
+	spin_unlock_irq(ring_lock);
+
+	return cnt;
+}
+
+/**
  * lpfc_cmf_setup - Initialize idle_stat tracking
  * @phba: Pointer to HBA context object.
  *
@@ -7890,36 +8053,19 @@
 lpfc_cmf_setup(struct lpfc_hba *phba)
 {
 	LPFC_MBOXQ_t *mboxq;
-	struct lpfc_mqe *mqe;
 	struct lpfc_dmabuf *mp;
 	struct lpfc_pc_sli4_params *sli4_params;
-	struct lpfc_sli4_parameters *mbx_sli4_parameters;
-	int length;
 	int rc, cmf, mi_ver;
 
+	rc = lpfc_sli4_refresh_params(phba);
+	if (unlikely(rc))
+		return rc;
+
 	mboxq = (LPFC_MBOXQ_t *)mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
 	if (!mboxq)
 		return -ENOMEM;
-	mqe = &mboxq->u.mqe;
-
-	/* Read the port's SLI4 Config Parameters */
-	length = (sizeof(struct lpfc_mbx_get_sli4_parameters) -
-		  sizeof(struct lpfc_sli4_cfg_mhdr));
-	lpfc_sli4_config(phba, mboxq, LPFC_MBOX_SUBSYSTEM_COMMON,
-			 LPFC_MBOX_OPCODE_GET_SLI4_PARAMETERS,
-			 length, LPFC_SLI4_MBX_EMBED);
-
-	rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
-	if (unlikely(rc)) {
-		mempool_free(mboxq, phba->mbox_mem_pool);
-		return rc;
-	}
 
-	/* Gather info on CMF and MI support */
 	sli4_params = &phba->sli4_hba.pc_sli4_params;
-	mbx_sli4_parameters = &mqe->un.get_sli4_parameters.sli4_parameters;
-	sli4_params->mi_ver = bf_get(cfg_mi_ver, mbx_sli4_parameters);
-	sli4_params->cmf = bf_get(cfg_cmf, mbx_sli4_parameters);
 
 	/* Are we forcing MI off via module parameter? */
 	if (!phba->cfg_enable_mi)
@@ -8014,6 +8160,10 @@
 			/* initialize congestion buffer info */
 			lpfc_init_congestion_buf(phba);
 			lpfc_init_congestion_stat(phba);
+
+			/* Zero out Congestion Signal counters */
+			atomic64_set(&phba->cgn_acqe_stat.alarm, 0);
+			atomic64_set(&phba->cgn_acqe_stat.warn, 0);
 		}
 
 		rc = lpfc_sli4_cgn_params_read(phba);
@@ -8070,19 +8220,29 @@
 	phba->cmf_interval_rate = LPFC_CMF_INTERVAL;
 
 	/* Allocate RX Monitor Buffer */
-	if (!phba->rxtable) {
-		phba->rxtable = kmalloc_array(LPFC_MAX_RXMONITOR_ENTRY,
-					      sizeof(struct rxtable_entry),
-					      GFP_KERNEL);
-		if (!phba->rxtable) {
+	if (!phba->rx_monitor) {
+		phba->rx_monitor = kzalloc(sizeof(*phba->rx_monitor),
+					   GFP_KERNEL);
+
+		if (!phba->rx_monitor) {
 			lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 					"2644 Failed to alloc memory "
 					"for RX Monitor Buffer\n");
 			return -ENOMEM;
 		}
+
+		/* Instruct the rx_monitor object to instantiate its ring */
+		if (lpfc_rx_monitor_create_ring(phba->rx_monitor,
+						LPFC_MAX_RXMONITOR_ENTRY)) {
+			kfree(phba->rx_monitor);
+			phba->rx_monitor = NULL;
+			lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+					"2645 Failed to alloc memory "
+					"for RX Monitor's Ring\n");
+			return -ENOMEM;
+		}
 	}
-	atomic_set(&phba->rxtable_idx_head, 0);
-	atomic_set(&phba->rxtable_idx_tail, 0);
+
 	return 0;
 }
 
@@ -8153,6 +8313,7 @@
 	struct lpfc_vport *vport = phba->pport;
 	struct lpfc_dmabuf *mp;
 	struct lpfc_rqb *rqbp;
+	u32 flg;
 
 	/* Perform a PCI function reset to start from clean */
 	rc = lpfc_pci_function_reset(phba);
@@ -8166,7 +8327,17 @@
 	else {
 		spin_lock_irq(&phba->hbalock);
 		phba->sli.sli_flag |= LPFC_SLI_ACTIVE;
+		flg = phba->sli.sli_flag;
 		spin_unlock_irq(&phba->hbalock);
+		/* Allow a little time after setting SLI_ACTIVE for any polled
+		 * MBX commands to complete via BSG.
+		 */
+		for (i = 0; i < 50 && (flg & LPFC_SLI_MBOX_ACTIVE); i++) {
+			msleep(20);
+			spin_lock_irq(&phba->hbalock);
+			flg = phba->sli.sli_flag;
+			spin_unlock_irq(&phba->hbalock);
+		}
 	}
 
 	lpfc_sli4_dip(phba);
@@ -9750,7 +9921,7 @@
 					"(%d):2541 Mailbox command x%x "
 					"(x%x/x%x) failure: "
 					"mqe_sta: x%x mcqe_sta: x%x/x%x "
-					"Data: x%x x%x\n,",
+					"Data: x%x x%x\n",
 					mboxq->vport ? mboxq->vport->vpi : 0,
 					mboxq->u.mb.mbxCommand,
 					lpfc_sli_config_mbox_subsys_get(phba,
@@ -9784,7 +9955,7 @@
 					"(%d):2597 Sync Mailbox command "
 					"x%x (x%x/x%x) failure: "
 					"mqe_sta: x%x mcqe_sta: x%x/x%x "
-					"Data: x%x x%x\n,",
+					"Data: x%x x%x\n",
 					mboxq->vport ? mboxq->vport->vpi : 0,
 					mboxq->u.mb.mbxCommand,
 					lpfc_sli_config_mbox_subsys_get(phba,
@@ -10010,7 +10181,7 @@
 		phba->lpfc_sli_brdready = lpfc_sli_brdready_s4;
 		break;
 	default:
-		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 				"1420 Invalid HBA PCI-device group: 0x%x\n",
 				dev_grp);
 		return -ENODEV;
@@ -11178,7 +11349,7 @@
 		phba->__lpfc_sli_issue_fcp_io = __lpfc_sli_issue_fcp_io_s4;
 		break;
 	default:
-		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 				"1419 Invalid HBA PCI-device group: 0x%x\n",
 				dev_grp);
 		return -ENODEV;
@@ -12404,17 +12575,17 @@
 
 	/* ABTS WQE must go to the same WQ as the WQE to be aborted */
 	abtsiocbp->hba_wqidx = cmdiocb->hba_wqidx;
-	if (cmdiocb->iocb_flag & LPFC_IO_FCP) {
-		abtsiocbp->iocb_flag |= LPFC_IO_FCP;
-		abtsiocbp->iocb_flag |= LPFC_USE_FCPWQIDX;
-	}
+	if (cmdiocb->iocb_flag & LPFC_IO_FCP)
+		abtsiocbp->iocb_flag |= (LPFC_IO_FCP | LPFC_USE_FCPWQIDX);
 	if (cmdiocb->iocb_flag & LPFC_IO_FOF)
 		abtsiocbp->iocb_flag |= LPFC_IO_FOF;
 
-	if (phba->link_state >= LPFC_LINK_UP)
-		iabt->ulpCommand = CMD_ABORT_XRI_CN;
-	else
+	if (phba->link_state < LPFC_LINK_UP ||
+	    (phba->sli_rev == LPFC_SLI_REV4 &&
+	     phba->sli4_hba.link_state.status == LPFC_FC_LA_TYPE_LINK_DOWN))
 		iabt->ulpCommand = CMD_CLOSE_XRI_CN;
+	else
+		iabt->ulpCommand = CMD_ABORT_XRI_CN;
 
 	if (cmpl)
 		abtsiocbp->iocb_cmpl = cmpl;
@@ -12488,15 +12659,54 @@
 }
 
 /**
- * lpfc_sli_validate_fcp_iocb - find commands associated with a vport or LUN
+ * lpfc_sli_validate_fcp_iocb_for_abort - filter iocbs appropriate for FCP aborts
+ * @iocbq: Pointer to iocb object.
+ * @vport: Pointer to driver virtual port object.
+ *
+ * This function acts as an iocb filter for functions which abort FCP iocbs.
+ *
+ * Return values
+ * -ENODEV, if a null iocb or vport ptr is encountered
+ * -EINVAL, if the iocb is not an FCP I/O, not on the TX cmpl queue, premarked as
+ *          driver already started the abort process, or is an abort iocb itself
+ * 0, passes criteria for aborting the FCP I/O iocb
+ **/
+static int
+lpfc_sli_validate_fcp_iocb_for_abort(struct lpfc_iocbq *iocbq,
+				     struct lpfc_vport *vport)
+{
+	IOCB_t *icmd = NULL;
+
+	/* No null ptr vports */
+	if (!iocbq || iocbq->vport != vport)
+		return -ENODEV;
+
+	/* iocb must be for FCP IO, already exists on the TX cmpl queue,
+	 * can't be premarked as driver aborted, nor be an ABORT iocb itself
+	 */
+	icmd = &iocbq->iocb;
+	if (!(iocbq->iocb_flag & LPFC_IO_FCP) ||
+	    !(iocbq->iocb_flag & LPFC_IO_ON_TXCMPLQ) ||
+	    (iocbq->iocb_flag & LPFC_DRIVER_ABORTED) ||
+	    (icmd->ulpCommand == CMD_ABORT_XRI_CN ||
+	     icmd->ulpCommand == CMD_CLOSE_XRI_CN))
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * lpfc_sli_validate_fcp_iocb - validate commands associated with a SCSI target
  * @iocbq: Pointer to driver iocb object.
  * @vport: Pointer to driver virtual port object.
  * @tgt_id: SCSI ID of the target.
  * @lun_id: LUN ID of the scsi device.
  * @ctx_cmd: LPFC_CTX_LUN/LPFC_CTX_TGT/LPFC_CTX_HOST
  *
- * This function acts as an iocb filter for functions which abort or count
- * all FCP iocbs pending on a lun/SCSI target/SCSI host. It will return
+ * This function acts as an iocb filter for validating a lun/SCSI target/SCSI
+ * host.
+ *
+ * It will return
  * 0 if the filtering criteria is met for the given iocb and will return
  * 1 if the filtering criteria is not met.
  * If ctx_cmd == LPFC_CTX_LUN, the function returns 0 only if the
@@ -12515,22 +12725,8 @@
 			   lpfc_ctx_cmd ctx_cmd)
 {
 	struct lpfc_io_buf *lpfc_cmd;
-	IOCB_t *icmd = NULL;
 	int rc = 1;
 
-	if (!iocbq || iocbq->vport != vport)
-		return rc;
-
-	if (!(iocbq->iocb_flag & LPFC_IO_FCP) ||
-	    !(iocbq->iocb_flag & LPFC_IO_ON_TXCMPLQ) ||
-	      iocbq->iocb_flag & LPFC_DRIVER_ABORTED)
-		return rc;
-
-	icmd = &iocbq->iocb;
-	if (icmd->ulpCommand == CMD_ABORT_XRI_CN ||
-	    icmd->ulpCommand == CMD_CLOSE_XRI_CN)
-		return rc;
-
 	lpfc_cmd = container_of(iocbq, struct lpfc_io_buf, cur_iocbq);
 
 	if (lpfc_cmd->pCmd == NULL)
@@ -12585,17 +12781,33 @@
 {
 	struct lpfc_hba *phba = vport->phba;
 	struct lpfc_iocbq *iocbq;
+	IOCB_t *icmd = NULL;
 	int sum, i;
+	unsigned long iflags;
 
-	spin_lock_irq(&phba->hbalock);
+	spin_lock_irqsave(&phba->hbalock, iflags);
 	for (i = 1, sum = 0; i <= phba->sli.last_iotag; i++) {
 		iocbq = phba->sli.iocbq_lookup[i];
 
-		if (lpfc_sli_validate_fcp_iocb (iocbq, vport, tgt_id, lun_id,
-						ctx_cmd) == 0)
+		if (!iocbq || iocbq->vport != vport)
+			continue;
+		if (!(iocbq->iocb_flag & LPFC_IO_FCP) ||
+		    !(iocbq->iocb_flag & LPFC_IO_ON_TXCMPLQ))
+			continue;
+
+		/* Include counting outstanding aborts */
+		icmd = &iocbq->iocb;
+		if (icmd->ulpCommand == CMD_ABORT_XRI_CN ||
+		    icmd->ulpCommand == CMD_CLOSE_XRI_CN) {
+			sum++;
+			continue;
+		}
+
+		if (lpfc_sli_validate_fcp_iocb(iocbq, vport, tgt_id, lun_id,
+					       ctx_cmd) == 0)
 			sum++;
 	}
-	spin_unlock_irq(&phba->hbalock);
+	spin_unlock_irqrestore(&phba->hbalock, iflags);
 
 	return sum;
 }
@@ -12662,7 +12874,11 @@
  *
  * This function sends an abort command for every SCSI command
  * associated with the given virtual port pending on the ring
- * filtered by lpfc_sli_validate_fcp_iocb function.
+ * filtered by lpfc_sli_validate_fcp_iocb_for_abort and then
+ * lpfc_sli_validate_fcp_iocb function.  The ordering for validation before
+ * submitting abort iocbs must be lpfc_sli_validate_fcp_iocb_for_abort
+ * followed by lpfc_sli_validate_fcp_iocb.
+ *
  * When abort_cmd == LPFC_CTX_LUN, the function sends abort only to the
  * FCP iocbs associated with lun specified by tgt_id and lun_id
  * parameters
@@ -12694,6 +12910,9 @@
 	for (i = 1; i <= phba->sli.last_iotag; i++) {
 		iocbq = phba->sli.iocbq_lookup[i];
 
+		if (lpfc_sli_validate_fcp_iocb_for_abort(iocbq, vport))
+			continue;
+
 		if (lpfc_sli_validate_fcp_iocb(iocbq, vport, tgt_id, lun_id,
 					       abort_cmd) != 0)
 			continue;
@@ -12726,7 +12945,11 @@
  *
  * This function sends an abort command for every SCSI command
  * associated with the given virtual port pending on the ring
- * filtered by lpfc_sli_validate_fcp_iocb function.
+ * filtered by lpfc_sli_validate_fcp_iocb_for_abort and then
+ * lpfc_sli_validate_fcp_iocb function.  The ordering for validation before
+ * submitting abort iocbs must be lpfc_sli_validate_fcp_iocb_for_abort
+ * followed by lpfc_sli_validate_fcp_iocb.
+ *
  * When taskmgmt_cmd == LPFC_CTX_LUN, the function sends abort only to the
  * FCP iocbs associated with lun specified by tgt_id and lun_id
  * parameters
@@ -12764,6 +12987,9 @@
 	for (i = 1; i <= phba->sli.last_iotag; i++) {
 		iocbq = phba->sli.iocbq_lookup[i];
 
+		if (lpfc_sli_validate_fcp_iocb_for_abort(iocbq, vport))
+			continue;
+
 		if (lpfc_sli_validate_fcp_iocb(iocbq, vport, tgt_id, lun_id,
 					       cmd) != 0)
 			continue;
@@ -13317,6 +13543,7 @@
 	uint32_t uerr_sta_hi, uerr_sta_lo;
 	uint32_t if_type, portsmphr;
 	struct lpfc_register portstat_reg;
+	u32 logmask;
 
 	/*
 	 * For now, use the SLI4 device internal unrecoverable error
@@ -13367,7 +13594,12 @@
 				readl(phba->sli4_hba.u.if_type2.ERR1regaddr);
 			phba->work_status[1] =
 				readl(phba->sli4_hba.u.if_type2.ERR2regaddr);
-			lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+			logmask = LOG_TRACE_EVENT;
+			if (phba->work_status[0] ==
+				SLIPORT_ERR1_REG_ERR_CODE_2 &&
+			    phba->work_status[1] == SLIPORT_ERR2_REG_FW_RESTART)
+				logmask = LOG_SLI;
+			lpfc_printf_log(phba, KERN_ERR, logmask,
 					"2885 Port Status Event: "
 					"port status reg 0x%x, "
 					"port smphr reg 0x%x, "
@@ -18389,7 +18621,6 @@
 	case FC_RCTL_ELS_REP:	/* extended link services reply */
 	case FC_RCTL_ELS4_REQ:	/* FC-4 ELS request */
 	case FC_RCTL_ELS4_REP:	/* FC-4 ELS reply */
-	case FC_RCTL_BA_NOP:  	/* basic link service NOP */
 	case FC_RCTL_BA_ABTS: 	/* basic link service abort */
 	case FC_RCTL_BA_RMC: 	/* remove connection */
 	case FC_RCTL_BA_ACC:	/* basic accept */
@@ -18410,6 +18641,7 @@
 		fc_vft_hdr = (struct fc_vft_header *)fc_hdr;
 		fc_hdr = &((struct fc_frame_header *)fc_vft_hdr)[1];
 		return lpfc_fc_frame_check(phba, fc_hdr);
+	case FC_RCTL_BA_NOP:	/* basic link service NOP */
 	default:
 		goto drop;
 	}
@@ -19222,12 +19454,14 @@
 	if (!lpfc_complete_unsol_iocb(phba,
 				      phba->sli4_hba.els_wq->pring,
 				      iocbq, fc_hdr->fh_r_ctl,
-				      fc_hdr->fh_type))
+				      fc_hdr->fh_type)) {
 		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
 				"2540 Ring %d handler: unexpected Rctl "
 				"x%x Type x%x received\n",
 				LPFC_ELS_RING,
 				fc_hdr->fh_r_ctl, fc_hdr->fh_type);
+		lpfc_in_buf_free(phba, &seq_dmabuf->dbuf);
+	}
 
 	/* Free iocb created in lpfc_prep_seq */
 	list_for_each_entry_safe(curr_iocb, next_iocb,
@@ -20817,6 +21051,7 @@
 	struct lpfc_mbx_wr_object *wr_object;
 	LPFC_MBOXQ_t *mbox;
 	int rc = 0, i = 0;
+	int mbox_status = 0;
 	uint32_t shdr_status, shdr_add_status, shdr_add_status_2;
 	uint32_t shdr_change_status = 0, shdr_csf = 0;
 	uint32_t mbox_tmo;
@@ -20862,11 +21097,15 @@
 	wr_object->u.request.bde_count = i;
 	bf_set(lpfc_wr_object_write_length, &wr_object->u.request, written);
 	if (!phba->sli4_hba.intr_enable)
-		rc = lpfc_sli_issue_mbox(phba, mbox, MBX_POLL);
+		mbox_status = lpfc_sli_issue_mbox(phba, mbox, MBX_POLL);
 	else {
 		mbox_tmo = lpfc_mbox_tmo_val(phba, mbox);
-		rc = lpfc_sli_issue_mbox_wait(phba, mbox, mbox_tmo);
+		mbox_status = lpfc_sli_issue_mbox_wait(phba, mbox, mbox_tmo);
 	}
+
+	/* The mbox status needs to be maintained to detect MBOX_TIMEOUT. */
+	rc = mbox_status;
+
 	/* The IOCTL status is embedded in the mailbox subheader. */
 	shdr_status = bf_get(lpfc_mbox_hdr_status,
 			     &wr_object->header.cfg_shdr.response);
@@ -20881,10 +21120,6 @@
 				  &wr_object->u.response);
 	}
 
-	if (!phba->sli4_hba.intr_enable)
-		mempool_free(mbox, phba->mbox_mem_pool);
-	else if (rc != MBX_TIMEOUT)
-		mempool_free(mbox, phba->mbox_mem_pool);
 	if (shdr_status || shdr_add_status || shdr_add_status_2 || rc) {
 		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
 				"3025 Write Object mailbox failed with "
@@ -20902,6 +21137,12 @@
 		lpfc_log_fw_write_cmpl(phba, shdr_status, shdr_add_status,
 				       shdr_add_status_2, shdr_change_status,
 				       shdr_csf);
+
+	if (!phba->sli4_hba.intr_enable)
+		mempool_free(mbox, phba->mbox_mem_pool);
+	else if (mbox_status != MBX_TIMEOUT)
+		mempool_free(mbox, phba->mbox_mem_pool);
+
 	return rc;
 }
 
@@ -21107,6 +21348,7 @@
 					fail_msg,
 					piocbq->iotag, piocbq->sli4_xritag);
 			list_add_tail(&piocbq->list, &completions);
+			fail_msg = NULL;
 		}
 		spin_unlock_irqrestore(&pring->ring_lock, iflags);
 	}
@@ -21909,20 +22151,20 @@
 static struct lpfc_io_buf *
 lpfc_get_io_buf_from_expedite_pool(struct lpfc_hba *phba)
 {
-	struct lpfc_io_buf *lpfc_ncmd;
+	struct lpfc_io_buf *lpfc_ncmd = NULL, *iter;
 	struct lpfc_io_buf *lpfc_ncmd_next;
 	unsigned long iflag;
 	struct lpfc_epd_pool *epd_pool;
 
 	epd_pool = &phba->epd_pool;
-	lpfc_ncmd = NULL;
 
 	spin_lock_irqsave(&epd_pool->lock, iflag);
 	if (epd_pool->count > 0) {
-		list_for_each_entry_safe(lpfc_ncmd, lpfc_ncmd_next,
+		list_for_each_entry_safe(iter, lpfc_ncmd_next,
 					 &epd_pool->list, list) {
-			list_del(&lpfc_ncmd->list);
+			list_del(&iter->list);
 			epd_pool->count--;
+			lpfc_ncmd = iter;
 			break;
 		}
 	}
@@ -21966,8 +22208,26 @@
 
 	qp = &phba->sli4_hba.hdwq[hwqid];
 	lpfc_ncmd = NULL;
+	if (!qp) {
+		lpfc_printf_log(phba, KERN_INFO,
+				LOG_SLI | LOG_NVME_ABTS | LOG_FCP,
+				"5556 NULL qp for hwqid  x%x\n", hwqid);
+		return lpfc_ncmd;
+	}
 	multixri_pool = qp->p_multixri_pool;
+	if (!multixri_pool) {
+		lpfc_printf_log(phba, KERN_INFO,
+				LOG_SLI | LOG_NVME_ABTS | LOG_FCP,
+				"5557 NULL multixri for hwqid  x%x\n", hwqid);
+		return lpfc_ncmd;
+	}
 	pvt_pool = &multixri_pool->pvt_pool;
+	if (!pvt_pool) {
+		lpfc_printf_log(phba, KERN_INFO,
+				LOG_SLI | LOG_NVME_ABTS | LOG_FCP,
+				"5558 NULL pvt_pool for hwqid  x%x\n", hwqid);
+		return lpfc_ncmd;
+	}
 	multixri_pool->io_req_count++;
 
 	/* If pvt_pool is empty, move some XRIs from public to private pool */
@@ -22043,6 +22303,12 @@
 
 	qp = &phba->sli4_hba.hdwq[hwqid];
 	lpfc_cmd = NULL;
+	if (!qp) {
+		lpfc_printf_log(phba, KERN_WARNING,
+				LOG_SLI | LOG_NVME_ABTS | LOG_FCP,
+				"5555 NULL qp for hwqid  x%x\n", hwqid);
+		return lpfc_cmd;
+	}
 
 	if (phba->cfg_xri_rebalancing)
 		lpfc_cmd = lpfc_get_io_buf_from_multixri_pools(
@@ -22095,10 +22361,6 @@
 	struct lpfc_dmabuf *pcmd;
 	u32 rd_object_name[LPFC_MBX_OBJECT_NAME_LEN_DW] = {0};
 
-	/* sanity check on queue memory */
-	if (!datap)
-		return -ENODEV;
-
 	mbox = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
 	if (!mbox)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_sli4.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_sli4.h
@@ -1116,6 +1116,8 @@
 int lpfc_sli4_resume_rpi(struct lpfc_nodelist *,
 			void (*)(struct lpfc_hba *, LPFC_MBOXQ_t *), void *);
 void lpfc_sli4_els_xri_abort_event_proc(struct lpfc_hba *phba);
+void lpfc_sli4_nvme_pci_offline_aborted(struct lpfc_hba *phba,
+					struct lpfc_io_buf *lpfc_ncmd);
 void lpfc_sli4_nvme_xri_aborted(struct lpfc_hba *phba,
 				struct sli4_wcqe_xri_aborted *axri,
 				struct lpfc_io_buf *lpfc_ncmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_version.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_version.h
@@ -20,7 +20,7 @@
  * included with this package.                                     *
  *******************************************************************/
 
-#define LPFC_DRIVER_VERSION "14.0.0.1"
+#define LPFC_DRIVER_VERSION "14.0.0.4"
 #define LPFC_DRIVER_NAME		"lpfc"
 
 /* Used for SLI 2/3 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/lpfc/lpfc_vport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/lpfc/lpfc_vport.c
@@ -486,22 +486,67 @@
 }
 
 static int
+lpfc_send_npiv_logo(struct lpfc_vport *vport, struct lpfc_nodelist *ndlp)
+{
+	int rc;
+	struct lpfc_hba *phba = vport->phba;
+
+	DECLARE_WAIT_QUEUE_HEAD_ONSTACK(waitq);
+
+	spin_lock_irq(&ndlp->lock);
+	if (!(ndlp->save_flags & NLP_WAIT_FOR_LOGO) &&
+	    !ndlp->logo_waitq) {
+		ndlp->logo_waitq = &waitq;
+		ndlp->nlp_fcp_info &= ~NLP_FCP_2_DEVICE;
+		ndlp->nlp_flag |= NLP_ISSUE_LOGO;
+		ndlp->save_flags |= NLP_WAIT_FOR_LOGO;
+	}
+	spin_unlock_irq(&ndlp->lock);
+	rc = lpfc_issue_els_npiv_logo(vport, ndlp);
+	if (!rc) {
+		wait_event_timeout(waitq,
+				   (!(ndlp->save_flags & NLP_WAIT_FOR_LOGO)),
+				   msecs_to_jiffies(phba->fc_ratov * 2000));
+
+		if (!(ndlp->save_flags & NLP_WAIT_FOR_LOGO))
+			goto logo_cmpl;
+		/* LOGO wait failed.  Correct status. */
+		rc = -EINTR;
+	} else {
+		rc = -EIO;
+	}
+
+	/* Error - clean up node flags. */
+	spin_lock_irq(&ndlp->lock);
+	ndlp->nlp_flag &= ~NLP_ISSUE_LOGO;
+	ndlp->save_flags &= ~NLP_WAIT_FOR_LOGO;
+	spin_unlock_irq(&ndlp->lock);
+
+ logo_cmpl:
+	lpfc_printf_vlog(vport, KERN_INFO, LOG_VPORT,
+			 "1824 Issue LOGO completes with status %d\n",
+			 rc);
+	spin_lock_irq(&ndlp->lock);
+	ndlp->logo_waitq = NULL;
+	spin_unlock_irq(&ndlp->lock);
+	return rc;
+}
+
+static int
 disable_vport(struct fc_vport *fc_vport)
 {
 	struct lpfc_vport *vport = *(struct lpfc_vport **)fc_vport->dd_data;
 	struct lpfc_hba   *phba = vport->phba;
 	struct lpfc_nodelist *ndlp = NULL, *next_ndlp = NULL;
-	long timeout;
 	struct Scsi_Host *shost = lpfc_shost_from_vport(vport);
 
+	/* Can't disable during an outstanding delete. */
+	if (vport->load_flag & FC_UNLOADING)
+		return 0;
+
 	ndlp = lpfc_findnode_did(vport, Fabric_DID);
-	if (ndlp && phba->link_state >= LPFC_LINK_UP) {
-		vport->unreg_vpi_cmpl = VPORT_INVAL;
-		timeout = msecs_to_jiffies(phba->fc_ratov * 2000);
-		if (!lpfc_issue_els_npiv_logo(vport, ndlp))
-			while (vport->unreg_vpi_cmpl == VPORT_INVAL && timeout)
-				timeout = schedule_timeout(timeout);
-	}
+	if (ndlp && phba->link_state >= LPFC_LINK_UP)
+		(void)lpfc_send_npiv_logo(vport, ndlp);
 
 	lpfc_sli_host_down(vport);
 
@@ -600,7 +645,7 @@
 	struct lpfc_vport *vport = *(struct lpfc_vport **)fc_vport->dd_data;
 	struct Scsi_Host *shost = lpfc_shost_from_vport(vport);
 	struct lpfc_hba  *phba = vport->phba;
-	long timeout;
+	int rc;
 
 	if (vport->port_type == LPFC_PHYSICAL_PORT) {
 		lpfc_printf_vlog(vport, KERN_ERR, LOG_TRACE_EVENT,
@@ -651,10 +696,6 @@
 	lpfc_free_sysfs_attr(vport);
 	lpfc_debugfs_terminate(vport);
 
-	/* Remove FC host to break driver binding. */
-	fc_remove_host(shost);
-	scsi_remove_host(shost);
-
 	/* Send the DA_ID and Fabric LOGO to cleanup Nameserver entries. */
 	ndlp = lpfc_findnode_did(vport, Fabric_DID);
 	if (!ndlp)
@@ -665,15 +706,14 @@
 	    phba->fc_topology != LPFC_TOPOLOGY_LOOP) {
 		if (vport->cfg_enable_da_id) {
 			/* Send DA_ID and wait for a completion. */
-			timeout = msecs_to_jiffies(phba->fc_ratov * 2000);
-			if (!lpfc_ns_cmd(vport, SLI_CTNS_DA_ID, 0, 0))
-				while (vport->ct_flags && timeout)
-					timeout = schedule_timeout(timeout);
-			else
+			rc = lpfc_ns_cmd(vport, SLI_CTNS_DA_ID, 0, 0);
+			if (rc) {
 				lpfc_printf_log(vport->phba, KERN_WARNING,
 						LOG_VPORT,
 						"1829 CT command failed to "
-						"delete objects on fabric\n");
+						"delete objects on fabric, "
+						"rc %d\n", rc);
+			}
 		}
 
 		/*
@@ -688,11 +728,10 @@
 		ndlp = lpfc_findnode_did(vport, Fabric_DID);
 		if (!ndlp)
 			goto skip_logo;
-		vport->unreg_vpi_cmpl = VPORT_INVAL;
-		timeout = msecs_to_jiffies(phba->fc_ratov * 2000);
-		if (!lpfc_issue_els_npiv_logo(vport, ndlp))
-			while (vport->unreg_vpi_cmpl == VPORT_INVAL && timeout)
-				timeout = schedule_timeout(timeout);
+
+		rc = lpfc_send_npiv_logo(vport, ndlp);
+		if (rc)
+			goto skip_logo;
 	}
 
 	if (!(phba->pport->load_flag & FC_UNLOADING))
@@ -700,6 +739,10 @@
 
 skip_logo:
 
+	/* Remove FC host to break driver binding. */
+	fc_remove_host(shost);
+	scsi_remove_host(shost);
+
 	lpfc_cleanup(vport);
 
 	/* Remove scsi host now.  The nodes are cleaned up. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mac_scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mac_scsi.c
@@ -102,11 +102,15 @@
  * Linux SCSI drivers lack knowledge of the timing behaviour of SCSI targets
  * so bus errors are unavoidable.
  *
- * If a MOVE.B instruction faults, we assume that zero bytes were transferred
- * and simply retry. That assumption probably depends on target behaviour but
- * seems to hold up okay. The NOP provides synchronization: without it the
- * fault can sometimes occur after the program counter has moved past the
- * offending instruction. Post-increment addressing can't be used.
+ * If a MOVE.B instruction faults during a receive operation, we assume the
+ * target sent nothing and try again. That assumption probably depends on
+ * target firmware but it seems to hold up okay. If a fault happens during a
+ * send operation, the target may or may not have seen /ACK and got the byte.
+ * It's uncertain so the whole SCSI command gets retried.
+ *
+ * The NOP is needed for synchronization because the fault address in the
+ * exception stack frame may or may not be the instruction that actually
+ * caused the bus error. Post-increment addressing can't be used.
  */
 
 #define MOVE_BYTE(operands) \
@@ -208,8 +212,6 @@
 		".previous                     \n" \
 		: "+a" (addr), "+r" (n), "+r" (result) : "a" (io))
 
-#define MAC_PDMA_DELAY		32
-
 static inline int mac_pdma_recv(void __iomem *io, unsigned char *start, int n)
 {
 	unsigned char *addr = start;
@@ -245,22 +247,21 @@
 	if (n >= 1) {
 		MOVE_BYTE("%0@,%3@");
 		if (result)
-			goto out;
+			return -1;
 	}
 	if (n >= 1 && ((unsigned long)addr & 1)) {
 		MOVE_BYTE("%0@,%3@");
 		if (result)
-			goto out;
+			return -2;
 	}
 	while (n >= 32)
 		MOVE_16_WORDS("%0@+,%3@");
 	while (n >= 2)
 		MOVE_WORD("%0@+,%3@");
 	if (result)
-		return start - addr; /* Negated to indicate uncertain length */
+		return start - addr - 1; /* Negated to indicate uncertain length */
 	if (n == 1)
 		MOVE_BYTE("%0@,%3@");
-out:
 	return addr - start;
 }
 
@@ -274,25 +275,56 @@
 	out_be32(hostdata->io + (CTRL_REG << 4), value);
 }
 
+static inline int macscsi_wait_for_drq(struct NCR5380_hostdata *hostdata)
+{
+	unsigned int n = 1; /* effectively multiplies NCR5380_REG_POLL_TIME */
+	unsigned char basr;
+
+again:
+	basr = NCR5380_read(BUS_AND_STATUS_REG);
+
+	if (!(basr & BASR_PHASE_MATCH))
+		return 1;
+
+	if (basr & BASR_IRQ)
+		return -1;
+
+	if (basr & BASR_DRQ)
+		return 0;
+
+	if (n-- == 0) {
+		NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
+		dsprintk(NDEBUG_PSEUDO_DMA, hostdata->host,
+			 "%s: DRQ timeout\n", __func__);
+		return -1;
+	}
+
+	NCR5380_poll_politely2(hostdata,
+			       BUS_AND_STATUS_REG, BASR_DRQ, BASR_DRQ,
+			       BUS_AND_STATUS_REG, BASR_PHASE_MATCH, 0, 0);
+	goto again;
+}
+
 static inline int macscsi_pread(struct NCR5380_hostdata *hostdata,
                                 unsigned char *dst, int len)
 {
 	u8 __iomem *s = hostdata->pdma_io + (INPUT_DATA_REG << 4);
 	unsigned char *d = dst;
-	int result = 0;
 
 	hostdata->pdma_residual = len;
 
-	while (!NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG,
-	                              BASR_DRQ | BASR_PHASE_MATCH,
-	                              BASR_DRQ | BASR_PHASE_MATCH, 0)) {
-		int bytes;
+	while (macscsi_wait_for_drq(hostdata) == 0) {
+		int bytes, chunk_bytes;
 
 		if (macintosh_config->ident == MAC_MODEL_IIFX)
 			write_ctrl_reg(hostdata, CTRL_HANDSHAKE_MODE |
 			                         CTRL_INTERRUPTS_ENABLE);
 
-		bytes = mac_pdma_recv(s, d, min(hostdata->pdma_residual, 512));
+		chunk_bytes = min(hostdata->pdma_residual, 512);
+		bytes = mac_pdma_recv(s, d, chunk_bytes);
+
+		if (macintosh_config->ident == MAC_MODEL_IIFX)
+			write_ctrl_reg(hostdata, CTRL_INTERRUPTS_ENABLE);
 
 		if (bytes > 0) {
 			d += bytes;
@@ -300,37 +332,25 @@
 		}
 
 		if (hostdata->pdma_residual == 0)
-			goto out;
+			break;
 
-		if (NCR5380_poll_politely2(hostdata, STATUS_REG, SR_REQ, SR_REQ,
-		                           BUS_AND_STATUS_REG, BASR_ACK,
-		                           BASR_ACK, 0) < 0)
-			scmd_printk(KERN_DEBUG, hostdata->connected,
-			            "%s: !REQ and !ACK\n", __func__);
-		if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH))
-			goto out;
+		if (bytes > 0)
+			continue;
 
-		if (bytes == 0)
-			udelay(MAC_PDMA_DELAY);
+		NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
+		dsprintk(NDEBUG_PSEUDO_DMA, hostdata->host,
+			 "%s: bus error [%d/%d] (%d/%d)\n",
+			 __func__, d - dst, len, bytes, chunk_bytes);
 
-		if (bytes >= 0)
+		if (bytes == 0)
 			continue;
 
-		dsprintk(NDEBUG_PSEUDO_DMA, hostdata->host,
-		         "%s: bus error (%d/%d)\n", __func__, d - dst, len);
-		NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
-		result = -1;
-		goto out;
+		if (macscsi_wait_for_drq(hostdata) <= 0)
+			set_host_byte(hostdata->connected, DID_ERROR);
+		break;
 	}
 
-	scmd_printk(KERN_ERR, hostdata->connected,
-	            "%s: phase mismatch or !DRQ\n", __func__);
-	NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
-	result = -1;
-out:
-	if (macintosh_config->ident == MAC_MODEL_IIFX)
-		write_ctrl_reg(hostdata, CTRL_INTERRUPTS_ENABLE);
-	return result;
+	return 0;
 }
 
 static inline int macscsi_pwrite(struct NCR5380_hostdata *hostdata,
@@ -338,77 +358,58 @@
 {
 	unsigned char *s = src;
 	u8 __iomem *d = hostdata->pdma_io + (OUTPUT_DATA_REG << 4);
-	int result = 0;
 
 	hostdata->pdma_residual = len;
 
-	while (!NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG,
-	                              BASR_DRQ | BASR_PHASE_MATCH,
-	                              BASR_DRQ | BASR_PHASE_MATCH, 0)) {
-		int bytes;
+	while (macscsi_wait_for_drq(hostdata) == 0) {
+		int bytes, chunk_bytes;
 
 		if (macintosh_config->ident == MAC_MODEL_IIFX)
 			write_ctrl_reg(hostdata, CTRL_HANDSHAKE_MODE |
 			                         CTRL_INTERRUPTS_ENABLE);
 
-		bytes = mac_pdma_send(s, d, min(hostdata->pdma_residual, 512));
+		chunk_bytes = min(hostdata->pdma_residual, 512);
+		bytes = mac_pdma_send(s, d, chunk_bytes);
+
+		if (macintosh_config->ident == MAC_MODEL_IIFX)
+			write_ctrl_reg(hostdata, CTRL_INTERRUPTS_ENABLE);
 
 		if (bytes > 0) {
 			s += bytes;
 			hostdata->pdma_residual -= bytes;
 		}
 
-		if (hostdata->pdma_residual == 0) {
-			if (NCR5380_poll_politely(hostdata, TARGET_COMMAND_REG,
-			                          TCR_LAST_BYTE_SENT,
-			                          TCR_LAST_BYTE_SENT,
-			                          0) < 0) {
-				scmd_printk(KERN_ERR, hostdata->connected,
-				            "%s: Last Byte Sent timeout\n", __func__);
-				result = -1;
-			}
-			goto out;
-		}
+		if (hostdata->pdma_residual == 0)
+			break;
 
-		if (NCR5380_poll_politely2(hostdata, STATUS_REG, SR_REQ, SR_REQ,
-		                           BUS_AND_STATUS_REG, BASR_ACK,
-		                           BASR_ACK, 0) < 0)
-			scmd_printk(KERN_DEBUG, hostdata->connected,
-			            "%s: !REQ and !ACK\n", __func__);
-		if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH))
-			goto out;
+		if (bytes > 0)
+			continue;
 
-		if (bytes == 0)
-			udelay(MAC_PDMA_DELAY);
+		NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
+		dsprintk(NDEBUG_PSEUDO_DMA, hostdata->host,
+			 "%s: bus error [%d/%d] (%d/%d)\n",
+			 __func__, s - src, len, bytes, chunk_bytes);
 
-		if (bytes >= 0)
+		if (bytes == 0)
 			continue;
 
-		dsprintk(NDEBUG_PSEUDO_DMA, hostdata->host,
-		         "%s: bus error (%d/%d)\n", __func__, s - src, len);
-		NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
-		result = -1;
-		goto out;
+		if (macscsi_wait_for_drq(hostdata) <= 0)
+			set_host_byte(hostdata->connected, DID_ERROR);
+		break;
 	}
 
-	scmd_printk(KERN_ERR, hostdata->connected,
-	            "%s: phase mismatch or !DRQ\n", __func__);
-	NCR5380_dprint(NDEBUG_PSEUDO_DMA, hostdata->host);
-	result = -1;
-out:
-	if (macintosh_config->ident == MAC_MODEL_IIFX)
-		write_ctrl_reg(hostdata, CTRL_INTERRUPTS_ENABLE);
-	return result;
+	return 0;
 }
 
 static int macscsi_dma_xfer_len(struct NCR5380_hostdata *hostdata,
                                 struct scsi_cmnd *cmd)
 {
-	if (hostdata->flags & FLAG_NO_PSEUDO_DMA ||
-	    cmd->SCp.this_residual < setup_use_pdma)
+	int resid = NCR5380_to_ncmd(cmd)->this_residual;
+
+	if (hostdata->flags & FLAG_NO_PSEUDO_DMA || resid < setup_use_pdma)
 		return 0;
 
-	return cmd->SCp.this_residual;
+	return resid;
 }
 
 static int macscsi_dma_residual(struct NCR5380_hostdata *hostdata)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/megaraid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/megaraid.c
@@ -1443,6 +1443,7 @@
 		 */
 		if (cmdid == CMDID_INT_CMDS) {
 			scb = &adapter->int_scb;
+			cmd = scb->cmd;
 
 			list_del_init(&scb->list);
 			scb->state = SCB_FREE;
@@ -4628,7 +4629,7 @@
 	 * major number allocation.
 	 */
 	major = register_chrdev(0, "megadev_legacy", &megadev_fops);
-	if (!major) {
+	if (major < 0) {
 		printk(KERN_WARNING
 				"megaraid: failed to register char device\n");
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/megaraid/megaraid_sas.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/megaraid/megaraid_sas.h
@@ -21,8 +21,8 @@
 /*
  * MegaRAID SAS Driver meta data
  */
-#define MEGASAS_VERSION				"07.717.02.00-rc1"
-#define MEGASAS_RELDATE				"May 19, 2021"
+#define MEGASAS_VERSION				"07.727.03.00-rc1"
+#define MEGASAS_RELDATE				"Oct 03, 2023"
 
 #define MEGASAS_MSIX_NAME_LEN			32
 
@@ -1517,6 +1517,8 @@
 #define MEGASAS_MAX_LD_IDS			(MEGASAS_MAX_LD_CHANNELS * \
 						MEGASAS_MAX_DEV_PER_CHANNEL)
 
+#define MEGASAS_MAX_SUPPORTED_LD_IDS		240
+
 #define MEGASAS_MAX_SECTORS                    (2*1024)
 #define MEGASAS_MAX_SECTORS_IEEE		(2*128)
 #define MEGASAS_DBG_LVL				1
@@ -2328,7 +2330,7 @@
 	u32 support_morethan256jbod; /* FW support for more than 256 PD/JBOD */
 	bool use_seqnum_jbod_fp;   /* Added for PD sequence */
 	bool smp_affinity_enable;
-	spinlock_t crashdump_lock;
+	struct mutex crashdump_lock;
 
 	struct megasas_register_set __iomem *reg_set;
 	u32 __iomem *reply_post_host_index_addr[MR_MAX_MSIX_REG_ARRAY];
@@ -2558,6 +2560,9 @@
 #define MEGASAS_IS_LOGICAL(sdev)					\
 	((sdev->channel < MEGASAS_MAX_PD_CHANNELS) ? 0 : 1)
 
+#define MEGASAS_IS_LUN_VALID(sdev)					\
+	(((sdev)->lun == 0) ? 1 : 0)
+
 #define MEGASAS_DEV_INDEX(scp)						\
 	(((scp->device->channel % 2) * MEGASAS_MAX_DEV_PER_CHANNEL) +	\
 	scp->device->id)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/megaraid/megaraid_sas_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/megaraid/megaraid_sas_base.c
@@ -263,13 +263,13 @@
 	 * Fusion registers could intermittently return all zeroes.
 	 * This behavior is transient in nature and subsequent reads will
 	 * return valid value. As a workaround in driver, retry readl for
-	 * upto three times until a non-zero value is read.
+	 * up to thirty times until a non-zero value is read.
 	 */
 	if (instance->adapter_type == AERO_SERIES) {
 		do {
 			ret_val = readl(addr);
 			i++;
-		} while (ret_val == 0 && i < 3);
+		} while (ret_val == 0 && i < 30);
 		return ret_val;
 	} else {
 		return readl(addr);
@@ -2126,6 +2126,9 @@
 			goto scan_target;
 		}
 		return -ENXIO;
+	} else if (!MEGASAS_IS_LUN_VALID(sdev)) {
+		sdev_printk(KERN_INFO, sdev, "%s: invalid LUN\n", __func__);
+		return -ENXIO;
 	}
 
 scan_target:
@@ -2156,6 +2159,10 @@
 	instance = megasas_lookup_instance(sdev->host->host_no);
 
 	if (MEGASAS_IS_LOGICAL(sdev)) {
+		if (!MEGASAS_IS_LUN_VALID(sdev)) {
+			sdev_printk(KERN_INFO, sdev, "%s: invalid LUN\n", __func__);
+			return;
+		}
 		ld_tgt_id = MEGASAS_TARGET_ID(sdev);
 		instance->ld_tgtid_status[ld_tgt_id] = LD_TARGET_ID_DELETED;
 		if (megasas_dbg_lvl & LD_PD_DEBUG)
@@ -3189,6 +3196,9 @@
 	qoff += map->nr_queues;
 	offset += map->nr_queues;
 
+	/* we never use READ queue, so can't cheat blk-mq */
+	shost->tag_set.map[HCTX_TYPE_READ].nr_queues = 0;
+
 	/* Setup Poll hctx */
 	map = &shost->tag_set.map[HCTX_TYPE_POLL];
 	map->nr_queues = instance->iopoll_q_count;
@@ -3265,14 +3275,13 @@
 	struct megasas_instance *instance =
 		(struct megasas_instance *) shost->hostdata;
 	int val = 0;
-	unsigned long flags;
 
 	if (kstrtoint(buf, 0, &val) != 0)
 		return -EINVAL;
 
-	spin_lock_irqsave(&instance->crashdump_lock, flags);
+	mutex_lock(&instance->crashdump_lock);
 	instance->fw_crash_buffer_offset = val;
-	spin_unlock_irqrestore(&instance->crashdump_lock, flags);
+	mutex_unlock(&instance->crashdump_lock);
 	return strlen(buf);
 }
 
@@ -3287,24 +3296,23 @@
 	unsigned long dmachunk = CRASH_DMA_BUF_SIZE;
 	unsigned long chunk_left_bytes;
 	unsigned long src_addr;
-	unsigned long flags;
 	u32 buff_offset;
 
-	spin_lock_irqsave(&instance->crashdump_lock, flags);
+	mutex_lock(&instance->crashdump_lock);
 	buff_offset = instance->fw_crash_buffer_offset;
-	if (!instance->crash_dump_buf &&
+	if (!instance->crash_dump_buf ||
 		!((instance->fw_crash_state == AVAILABLE) ||
 		(instance->fw_crash_state == COPYING))) {
 		dev_err(&instance->pdev->dev,
 			"Firmware crash dump is not available\n");
-		spin_unlock_irqrestore(&instance->crashdump_lock, flags);
+		mutex_unlock(&instance->crashdump_lock);
 		return -EINVAL;
 	}
 
 	if (buff_offset > (instance->fw_crash_buffer_size * dmachunk)) {
 		dev_err(&instance->pdev->dev,
 			"Firmware crash dump offset is out of range\n");
-		spin_unlock_irqrestore(&instance->crashdump_lock, flags);
+		mutex_unlock(&instance->crashdump_lock);
 		return 0;
 	}
 
@@ -3316,7 +3324,7 @@
 	src_addr = (unsigned long)instance->crash_buf[buff_offset / dmachunk] +
 		(buff_offset % dmachunk);
 	memcpy(buf, (void *)src_addr, size);
-	spin_unlock_irqrestore(&instance->crashdump_lock, flags);
+	mutex_unlock(&instance->crashdump_lock);
 
 	return size;
 }
@@ -3341,7 +3349,6 @@
 	struct megasas_instance *instance =
 		(struct megasas_instance *) shost->hostdata;
 	int val = 0;
-	unsigned long flags;
 
 	if (kstrtoint(buf, 0, &val) != 0)
 		return -EINVAL;
@@ -3355,9 +3362,9 @@
 	instance->fw_crash_state = val;
 
 	if ((val == COPIED) || (val == COPY_ERROR)) {
-		spin_lock_irqsave(&instance->crashdump_lock, flags);
+		mutex_lock(&instance->crashdump_lock);
 		megasas_free_host_crash_buffer(instance);
-		spin_unlock_irqrestore(&instance->crashdump_lock, flags);
+		mutex_unlock(&instance->crashdump_lock);
 		if (val == COPY_ERROR)
 			dev_info(&instance->pdev->dev, "application failed to "
 				"copy Firmware crash dump\n");
@@ -5147,9 +5154,9 @@
 		fusion->current_map_sz = ventura_map_sz;
 		fusion->max_map_sz = ventura_map_sz;
 	} else {
-		fusion->old_map_sz =  sizeof(struct MR_FW_RAID_MAP) +
-					(sizeof(struct MR_LD_SPAN_MAP) *
-					(instance->fw_supported_vd_count - 1));
+		fusion->old_map_sz =
+			struct_size((struct MR_FW_RAID_MAP *)0, ldSpanMap,
+				    instance->fw_supported_vd_count);
 		fusion->new_map_sz =  sizeof(struct MR_FW_RAID_MAP_EXT);
 
 		fusion->max_map_sz =
@@ -5782,10 +5789,10 @@
 {
 	int i;
 	struct fusion_context *fusion = instance->ctrl_context;
-	u32 pd_seq_map_sz;
+	size_t pd_seq_map_sz;
 
-	pd_seq_map_sz = sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC) +
-		(sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1));
+	pd_seq_map_sz = struct_size((struct MR_PD_CFG_SEQ_NUM_SYNC *)0, seq,
+				    MAX_PHYSICAL_DEVICES);
 
 	instance->use_seqnum_jbod_fp =
 		instance->support_seqnum_jbod_fp;
@@ -7422,7 +7429,7 @@
 	init_waitqueue_head(&instance->int_cmd_wait_q);
 	init_waitqueue_head(&instance->abort_cmd_wait_q);
 
-	spin_lock_init(&instance->crashdump_lock);
+	mutex_init(&instance->crashdump_lock);
 	spin_lock_init(&instance->mfi_pool_lock);
 	spin_lock_init(&instance->hba_lock);
 	spin_lock_init(&instance->stream_lock);
@@ -7961,7 +7968,7 @@
 	struct Scsi_Host *host;
 	struct megasas_instance *instance;
 	struct fusion_context *fusion;
-	u32 pd_seq_map_sz;
+	size_t pd_seq_map_sz;
 
 	instance = pci_get_drvdata(pdev);
 
@@ -8033,9 +8040,9 @@
 
 	if (instance->adapter_type != MFI_SERIES) {
 		megasas_release_fusion(instance);
-		pd_seq_map_sz = sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC) +
-				(sizeof(struct MR_PD_CFG_SEQ) *
-					(MAX_PHYSICAL_DEVICES - 1));
+		pd_seq_map_sz =
+			struct_size((struct MR_PD_CFG_SEQ_NUM_SYNC *)0,
+				    seq, MAX_PHYSICAL_DEVICES);
 		for (i = 0; i < 2 ; i++) {
 			if (fusion->ld_map[i])
 				dma_free_coherent(&instance->pdev->dev,
@@ -8915,8 +8922,11 @@
 						   (ld_target_id / MEGASAS_MAX_DEV_PER_CHANNEL),
 						   (ld_target_id - MEGASAS_MAX_DEV_PER_CHANNEL),
 						   0);
-			if (sdev1)
+			if (sdev1) {
+				mutex_unlock(&instance->reset_mutex);
 				megasas_remove_scsi_device(sdev1);
+				mutex_lock(&instance->reset_mutex);
+			}
 
 			event_type = SCAN_VD_CHANNEL;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/megaraid/megaraid_sas_fp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/megaraid/megaraid_sas_fp.c
@@ -326,9 +326,9 @@
 	else if (instance->supportmax256vd)
 		expected_size = sizeof(struct MR_FW_RAID_MAP_EXT);
 	else
-		expected_size =
-			(sizeof(struct MR_FW_RAID_MAP) - sizeof(struct MR_LD_SPAN_MAP) +
-			(sizeof(struct MR_LD_SPAN_MAP) * le16_to_cpu(pDrvRaidMap->ldCount)));
+		expected_size = struct_size((struct MR_FW_RAID_MAP *)0,
+					    ldSpanMap,
+					    le16_to_cpu(pDrvRaidMap->ldCount));
 
 	if (le32_to_cpu(pDrvRaidMap->totalSize) != expected_size) {
 		dev_dbg(&instance->pdev->dev, "megasas: map info structure size 0x%x",
@@ -358,7 +358,7 @@
 		ld = MR_TargetIdToLdGet(i, drv_map);
 
 		/* For non existing VDs, iterate to next VD*/
-		if (ld >= (MAX_LOGICAL_DRIVES_EXT - 1))
+		if (ld >= MEGASAS_MAX_SUPPORTED_LD_IDS)
 			continue;
 
 		raid = MR_LdRaidGet(ld, drv_map);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/megaraid/megaraid_sas_fusion.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/megaraid/megaraid_sas_fusion.c
@@ -1310,7 +1310,7 @@
 
 	pd_sync = (void *)fusion->pd_seq_sync[(instance->pd_seq_map_id & 1)];
 	pd_seq_h = fusion->pd_seq_phys[(instance->pd_seq_map_id & 1)];
-	pd_seq_map_sz = struct_size(pd_sync, seq, MAX_PHYSICAL_DEVICES - 1);
+	pd_seq_map_sz = struct_size(pd_sync, seq, MAX_PHYSICAL_DEVICES);
 
 	cmd = megasas_get_cmd(instance);
 	if (!cmd) {
@@ -3530,6 +3530,9 @@
 	if (atomic_read(&instance->adprecovery) == MEGASAS_HW_CRITICAL_ERROR)
 		return IRQ_HANDLED;
 
+	if (irq_context && !atomic_add_unless(&irq_context->in_used, 1, 1))
+		return 0;
+
 	desc = fusion->reply_frames_desc[MSIxIndex] +
 				fusion->last_reply_idx[MSIxIndex];
 
@@ -3540,11 +3543,11 @@
 	reply_descript_type = reply_desc->ReplyFlags &
 		MPI2_RPY_DESCRIPT_FLAGS_TYPE_MASK;
 
-	if (reply_descript_type == MPI2_RPY_DESCRIPT_FLAGS_UNUSED)
+	if (reply_descript_type == MPI2_RPY_DESCRIPT_FLAGS_UNUSED) {
+		if (irq_context)
+			atomic_dec(&irq_context->in_used);
 		return IRQ_NONE;
-
-	if (irq_context && !atomic_add_unless(&irq_context->in_used, 1, 1))
-		return 0;
+	}
 
 	num_completed = 0;
 
@@ -4231,6 +4234,9 @@
 	}
 
 out:
+	if (!retval && reason == SCSIIO_TIMEOUT_OCR)
+		dev_info(&instance->pdev->dev, "IO is completed, no OCR is required\n");
+
 	return retval;
 }
 
@@ -4734,7 +4740,7 @@
 	devhandle = megasas_get_tm_devhandle(scmd->device);
 
 	if (devhandle == (u16)ULONG_MAX) {
-		ret = SUCCESS;
+		ret = FAILED;
 		sdev_printk(KERN_INFO, scmd->device,
 			"task abort issued for invalid devhandle\n");
 		mutex_unlock(&instance->reset_mutex);
@@ -4804,7 +4810,7 @@
 	devhandle = megasas_get_tm_devhandle(scmd->device);
 
 	if (devhandle == (u16)ULONG_MAX) {
-		ret = SUCCESS;
+		ret = FAILED;
 		sdev_printk(KERN_INFO, scmd->device,
 			"target reset issued for invalid devhandle\n");
 		mutex_unlock(&instance->reset_mutex);
@@ -5276,7 +5282,6 @@
 		if (!fusion->log_to_span) {
 			dev_err(&instance->pdev->dev, "Failed from %s %d\n",
 				__func__, __LINE__);
-			kfree(instance->ctrl_context);
 			return -ENOMEM;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/megaraid/megaraid_sas_fusion.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/megaraid/megaraid_sas_fusion.h
@@ -942,7 +942,7 @@
 	u8                  reserved2[7];
 	struct MR_ARRAY_INFO       arMapInfo[MAX_RAIDMAP_ARRAYS];
 	struct MR_DEV_HANDLE_INFO  devHndlInfo[MAX_RAIDMAP_PHYSICAL_DEVICES];
-	struct MR_LD_SPAN_MAP      ldSpanMap[1];
+	struct MR_LD_SPAN_MAP      ldSpanMap[];
 };
 
 struct IO_REQUEST_INFO {
@@ -1053,7 +1053,7 @@
 	struct MR_RAID_MAP_DESC_TABLE
 			raid_map_desc_table[RAID_MAP_DESC_TYPE_COUNT];
 	/* Variable Size buffer containing all data */
-	u32 raid_map_desc_data[1];
+	u32 raid_map_desc_data[];
 }; /* Dynamicaly sized RAID MAp structure */
 
 #define IEEE_SGE_FLAGS_ADDR_MASK            (0x03)
@@ -1148,7 +1148,7 @@
 
 struct MR_FW_RAID_MAP_ALL {
 	struct MR_FW_RAID_MAP raidMap;
-	struct MR_LD_SPAN_MAP ldSpanMap[MAX_LOGICAL_DRIVES - 1];
+	struct MR_LD_SPAN_MAP ldSpanMap[MAX_LOGICAL_DRIVES];
 } __attribute__ ((packed));
 
 struct MR_DRV_RAID_MAP {
@@ -1182,7 +1182,7 @@
 		devHndlInfo[MAX_RAIDMAP_PHYSICAL_DEVICES_DYN];
 	u16 ldTgtIdToLd[MAX_LOGICAL_DRIVES_DYN];
 	struct MR_ARRAY_INFO arMapInfo[MAX_API_ARRAYS_DYN];
-	struct MR_LD_SPAN_MAP      ldSpanMap[1];
+	struct MR_LD_SPAN_MAP      ldSpanMap[];
 
 };
 
@@ -1193,7 +1193,7 @@
 struct MR_DRV_RAID_MAP_ALL {
 
 	struct MR_DRV_RAID_MAP raidMap;
-	struct MR_LD_SPAN_MAP ldSpanMap[MAX_LOGICAL_DRIVES_DYN - 1];
+	struct MR_LD_SPAN_MAP ldSpanMap[MAX_LOGICAL_DRIVES_DYN];
 } __packed;
 
 
@@ -1249,7 +1249,7 @@
 struct MR_PD_CFG_SEQ_NUM_SYNC {
 	__le32 size;
 	__le32 count;
-	struct MR_PD_CFG_SEQ seq[1];
+	struct MR_PD_CFG_SEQ seq[];
 } __packed;
 
 /* stream detection */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/Kconfig
@@ -3,5 +3,6 @@
 config SCSI_MPI3MR
 	tristate "Broadcom MPI3 Storage Controller Device Driver"
 	depends on PCI && SCSI
+	select BLK_DEV_BSGLIB
 	help
 	MPI3 based Storage & RAID Controllers Driver.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/Makefile
@@ -1,4 +1,5 @@
 # mpi3mr makefile
-obj-m += mpi3mr.o
+obj-$(CONFIG_SCSI_MPI3MR) += mpi3mr.o
 mpi3mr-y +=  mpi3mr_os.o     \
 		mpi3mr_fw.o \
+		mpi3mr_app.o \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_cnfg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_cnfg.h
@@ -8,7 +8,7 @@
 #define MPI3_CONFIG_PAGETYPE_IO_UNIT                    (0x00)
 #define MPI3_CONFIG_PAGETYPE_MANUFACTURING              (0x01)
 #define MPI3_CONFIG_PAGETYPE_IOC                        (0x02)
-#define MPI3_CONFIG_PAGETYPE_UEFI_BSD                   (0x03)
+#define MPI3_CONFIG_PAGETYPE_DRIVER                     (0x03)
 #define MPI3_CONFIG_PAGETYPE_SECURITY                   (0x04)
 #define MPI3_CONFIG_PAGETYPE_ENCLOSURE                  (0x11)
 #define MPI3_CONFIG_PAGETYPE_DEVICE                     (0x12)
@@ -181,8 +181,16 @@
 #define MPI3_SAS_HWRATE_MIN_RATE_6_0                    (0x0a)
 #define MPI3_SAS_HWRATE_MIN_RATE_12_0                   (0x0b)
 #define MPI3_SAS_HWRATE_MIN_RATE_22_5                   (0x0c)
-#define MPI3_SLOT_INVALID                           (0xffff)
-#define MPI3_SLOT_INDEX_INVALID                     (0xffff)
+#define MPI3_SLOT_INVALID                               (0xffff)
+#define MPI3_SLOT_INDEX_INVALID                         (0xffff)
+#define MPI3_LINK_CHANGE_COUNT_INVALID                   (0xffff)
+#define MPI3_RATE_CHANGE_COUNT_INVALID                   (0xffff)
+#define MPI3_TEMP_SENSOR_LOCATION_INTERNAL              (0x0)
+#define MPI3_TEMP_SENSOR_LOCATION_INLET                 (0x1)
+#define MPI3_TEMP_SENSOR_LOCATION_OUTLET                (0x2)
+#define MPI3_TEMP_SENSOR_LOCATION_DRAM                  (0x3)
+#define MPI3_MFGPAGE_VENDORID_BROADCOM                  (0x1000)
+#define MPI3_MFGPAGE_DEVID_SAS4116                      (0x00a5)
 struct mpi3_man_page0 {
 	struct mpi3_config_page_header         header;
 	u8                                 chip_revision[8];
@@ -194,8 +202,8 @@
 	__le32                             reserved94;
 	__le32                             reserved98;
 	u8                                 oem;
-	u8                                 sub_oem;
-	__le16                             reserved9e;
+	u8                                 profile_identifier;
+	__le16                             flags;
 	u8                                 board_mfg_day;
 	u8                                 board_mfg_month;
 	__le16                             board_mfg_year;
@@ -208,6 +216,8 @@
 };
 
 #define MPI3_MAN0_PAGEVERSION       (0x00)
+#define MPI3_MAN0_FLAGS_SWITCH_PRESENT                       (0x0002)
+#define MPI3_MAN0_FLAGS_EXPANDER_PRESENT                     (0x0001)
 #define MPI3_MAN1_VPD_SIZE                                   (512)
 struct mpi3_man_page1 {
 	struct mpi3_config_page_header         header;
@@ -236,7 +246,7 @@
 #define MPI3_MAN5_PAGEVERSION                                (0x00)
 struct mpi3_man6_gpio_entry {
 	u8         function_code;
-	u8         reserved01;
+	u8         function_flags;
 	__le16     flags;
 	u8         param1;
 	u8         param2;
@@ -253,16 +263,24 @@
 #define MPI3_MAN6_GPIO_FUNCTION_PORT_STATUS_YELLOW                            (0x06)
 #define MPI3_MAN6_GPIO_FUNCTION_CABLE_MANAGEMENT                              (0x07)
 #define MPI3_MAN6_GPIO_FUNCTION_BKPLANE_MGMT_TYPE                             (0x08)
-#define MPI3_MAN6_GPIO_FUNCTION_ISTWI_MUX_RESET                               (0x09)
 #define MPI3_MAN6_GPIO_FUNCTION_ISTWI_RESET                                   (0x0a)
 #define MPI3_MAN6_GPIO_FUNCTION_BACKEND_PCIE_RESET                            (0x0b)
 #define MPI3_MAN6_GPIO_FUNCTION_GLOBAL_FAULT                                  (0x0c)
-#define MPI3_MAN6_GPIO_FUNCTION_EPACK_ATTN                                    (0x0d)
+#define MPI3_MAN6_GPIO_FUNCTION_PBLP_STATUS_CHANGE                            (0x0d)
 #define MPI3_MAN6_GPIO_FUNCTION_EPACK_ONLINE                                  (0x0e)
 #define MPI3_MAN6_GPIO_FUNCTION_EPACK_FAULT                                   (0x0f)
 #define MPI3_MAN6_GPIO_FUNCTION_CTRL_TYPE                                     (0x10)
 #define MPI3_MAN6_GPIO_FUNCTION_LICENSE                                       (0x11)
 #define MPI3_MAN6_GPIO_FUNCTION_REFCLK_CONTROL                                (0x12)
+#define MPI3_MAN6_GPIO_FUNCTION_BACKEND_PCIE_RESET_CLAMP                      (0x13)
+#define MPI3_MAN6_GPIO_FUNCTION_AUXILIARY_POWER                               (0x14)
+#define MPI3_MAN6_GPIO_FUNCTION_RAID_DATA_CACHE_DIRTY                         (0x15)
+#define MPI3_MAN6_GPIO_FUNCTION_BOARD_FAN_CONTROL                             (0x16)
+#define MPI3_MAN6_GPIO_FUNCTION_BOARD_FAN_FAULT                               (0x17)
+#define MPI3_MAN6_GPIO_FUNCTION_POWER_BRAKE                                   (0x18)
+#define MPI3_MAN6_GPIO_ISTWI_RESET_FUNCTIONFLAGS_DEVSELECT_MASK               (0x01)
+#define MPI3_MAN6_GPIO_ISTWI_RESET_FUNCTIONFLAGS_DEVSELECT_ISTWI              (0x00)
+#define MPI3_MAN6_GPIO_ISTWI_RESET_FUNCTIONFLAGS_DEVSELECT_RECEPTACLEID       (0x01)
 #define MPI3_MAN6_GPIO_EXTINT_PARAM1_FLAGS_SOURCE_MASK                        (0xf0)
 #define MPI3_MAN6_GPIO_EXTINT_PARAM1_FLAGS_SOURCE_GENERIC                     (0x00)
 #define MPI3_MAN6_GPIO_EXTINT_PARAM1_FLAGS_SOURCE_CABLE_MGMT                  (0x10)
@@ -275,8 +293,6 @@
 #define MPI3_MAN6_GPIO_CABLE_MGMT_PARAM1_INTERFACE_MODULE_PRESENT             (0x00)
 #define MPI3_MAN6_GPIO_CABLE_MGMT_PARAM1_INTERFACE_ACTIVE_CABLE_ENABLE        (0x01)
 #define MPI3_MAN6_GPIO_CABLE_MGMT_PARAM1_INTERFACE_CABLE_MGMT_ENABLE          (0x02)
-#define MPI3_MAN6_GPIO_ISTWI_MUX_RESET_PARAM2_SPEC_MUX                        (0x00)
-#define MPI3_MAN6_GPIO_ISTWI_MUX_RESET_PARAM2_ALL_MUXES                       (0x01)
 #define MPI3_MAN6_GPIO_LICENSE_PARAM1_TYPE_IBUTTON                            (0x00)
 #define MPI3_MAN6_GPIO_FLAGS_SLEW_RATE_MASK                                   (0x0100)
 #define MPI3_MAN6_GPIO_FLAGS_SLEW_RATE_FAST_EDGE                              (0x0100)
@@ -353,6 +369,7 @@
 	__le32                             reserved0c;
 };
 
+#define MPI3_MAN8_PHY_INFO_RECEPTACLE_ID_HOST_PHY          (0xff)
 #ifndef MPI3_MAN8_PHY_INFO_MAX
 #define MPI3_MAN8_PHY_INFO_MAX                      (1)
 #endif
@@ -373,20 +390,22 @@
 };
 
 enum mpi3_man9_resources {
-	MPI3_MAN9_RSRC_OUTSTANDING_REQS = 0,
-	MPI3_MAN9_RSRC_TARGET_CMDS      = 1,
-	MPI3_MAN9_RSRC_SAS_TARGETS      = 2,
-	MPI3_MAN9_RSRC_PCIE_TARGETS     = 3,
-	MPI3_MAN9_RSRC_INITIATORS       = 4,
-	MPI3_MAN9_RSRC_VDS              = 5,
-	MPI3_MAN9_RSRC_ENCLOSURES       = 6,
-	MPI3_MAN9_RSRC_ENCLOSURE_PHYS   = 7,
-	MPI3_MAN9_RSRC_EXPANDERS        = 8,
-	MPI3_MAN9_RSRC_PCIE_SWITCHES    = 9,
-	MPI3_MAN9_RSRC_PDS              = 10,
-	MPI3_MAN9_RSRC_HOST_PDS         = 11,
-	MPI3_MAN9_RSRC_ADV_HOST_PDS     = 12,
-	MPI3_MAN9_RSRC_RAID_PDS         = 13,
+	MPI3_MAN9_RSRC_OUTSTANDING_REQS    = 0,
+	MPI3_MAN9_RSRC_TARGET_CMDS         = 1,
+	MPI3_MAN9_RSRC_RESERVED02          = 2,
+	MPI3_MAN9_RSRC_NVME                = 3,
+	MPI3_MAN9_RSRC_INITIATORS          = 4,
+	MPI3_MAN9_RSRC_VDS                 = 5,
+	MPI3_MAN9_RSRC_ENCLOSURES          = 6,
+	MPI3_MAN9_RSRC_ENCLOSURE_PHYS      = 7,
+	MPI3_MAN9_RSRC_EXPANDERS           = 8,
+	MPI3_MAN9_RSRC_PCIE_SWITCHES       = 9,
+	MPI3_MAN9_RSRC_RESERVED10          = 10,
+	MPI3_MAN9_RSRC_HOST_PD_DRIVES      = 11,
+	MPI3_MAN9_RSRC_ADV_HOST_PD_DRIVES  = 12,
+	MPI3_MAN9_RSRC_RAID_PD_DRIVES      = 13,
+	MPI3_MAN9_RSRC_DRV_DIAG_BUF        = 14,
+	MPI3_MAN9_RSRC_NAMESPACE_COUNT     = 15,
 	MPI3_MAN9_RSRC_NUM_RESOURCES
 };
 
@@ -394,17 +413,22 @@
 #define MPI3_MAN9_MAX_OUTSTANDING_REQS      (65000)
 #define MPI3_MAN9_MIN_TARGET_CMDS           (0)
 #define MPI3_MAN9_MAX_TARGET_CMDS           (65535)
-#define MPI3_MAN9_MIN_SAS_TARGETS           (0)
-#define MPI3_MAN9_MAX_SAS_TARGETS           (65535)
-#define MPI3_MAN9_MIN_PCIE_TARGETS          (0)
+#define MPI3_MAN9_MIN_NVME_TARGETS          (0)
 #define MPI3_MAN9_MIN_INITIATORS            (0)
-#define MPI3_MAN9_MAX_INITIATORS            (65535)
-#define MPI3_MAN9_MIN_ENCLOSURES            (0)
+#define MPI3_MAN9_MIN_VDS                   (0)
+#define MPI3_MAN9_MIN_ENCLOSURES            (1)
 #define MPI3_MAN9_MAX_ENCLOSURES            (65535)
 #define MPI3_MAN9_MIN_ENCLOSURE_PHYS        (0)
 #define MPI3_MAN9_MIN_EXPANDERS             (0)
 #define MPI3_MAN9_MAX_EXPANDERS             (65535)
 #define MPI3_MAN9_MIN_PCIE_SWITCHES         (0)
+#define MPI3_MAN9_MIN_HOST_PD_DRIVES        (0)
+#define MPI3_MAN9_ADV_HOST_PD_DRIVES        (0)
+#define MPI3_MAN9_RAID_PD_DRIVES            (0)
+#define MPI3_MAN9_DRIVER_DIAG_BUFFER        (0)
+#define MPI3_MAN9_MIN_NAMESPACE_COUNT       (1)
+#define MPI3_MAN9_MIN_EXPANDERS             (0)
+#define MPI3_MAN9_MAX_EXPANDERS             (65535)
 struct mpi3_man_page9 {
 	struct mpi3_config_page_header         header;
 	u8                                 num_resources;
@@ -422,9 +446,14 @@
 struct mpi3_man10_istwi_ctrlr_entry {
 	__le16     slave_address;
 	__le16     flags;
-	__le32     reserved04;
+	u8         scl_low_override;
+	u8         scl_high_override;
+	__le16     reserved06;
 };
 
+#define MPI3_MAN10_ISTWI_CTRLR_FLAGS_BUS_SPEED_MASK         (0x000c)
+#define MPI3_MAN10_ISTWI_CTRLR_FLAGS_BUS_SPEED_100K         (0x0000)
+#define MPI3_MAN10_ISTWI_CTRLR_FLAGS_BUS_SPEED_400K         (0x0004)
 #define MPI3_MAN10_ISTWI_CTRLR_FLAGS_SLAVE_ENABLED          (0x0002)
 #define MPI3_MAN10_ISTWI_CTRLR_FLAGS_MASTER_ENABLED         (0x0001)
 #ifndef MPI3_MAN10_ISTWI_CTRLR_MAX
@@ -451,10 +480,13 @@
 	u8         temp_channel[4];
 };
 
-#define MPI3_MAN11_TEMP_SENSOR_TYPE_MAX6654         (0x00)
-#define MPI3_MAN11_TEMP_SENSOR_TYPE_EMC1442         (0x01)
-#define MPI3_MAN11_TEMP_SENSOR_TYPE_ADT7476         (0x02)
-#define MPI3_MAN11_TEMP_SENSOR_CHANNEL_ENABLED      (0x01)
+#define MPI3_MAN11_TEMP_SENSOR_TYPE_MAX6654                (0x00)
+#define MPI3_MAN11_TEMP_SENSOR_TYPE_EMC1442                (0x01)
+#define MPI3_MAN11_TEMP_SENSOR_TYPE_ADT7476                (0x02)
+#define MPI3_MAN11_TEMP_SENSOR_TYPE_SE97B                  (0x03)
+#define MPI3_MAN11_TEMP_SENSOR_CHANNEL_LOCATION_MASK       (0xe0)
+#define MPI3_MAN11_TEMP_SENSOR_CHANNEL_LOCATION_SHIFT      (5)
+#define MPI3_MAN11_TEMP_SENSOR_CHANNEL_ENABLED             (0x01)
 struct mpi3_man11_seeprom_device_format {
 	u8         size;
 	u8         page_write_size;
@@ -495,31 +527,40 @@
 #define MPI3_MAN11_BKPLANE_UBM_FLAGS_MAX_FRU_SHIFT                 (4)
 #define MPI3_MAN11_BKPLANE_UBM_FLAGS_POLL_INTERVAL_MASK            (0x000f)
 #define MPI3_MAN11_BKPLANE_UBM_FLAGS_POLL_INTERVAL_SHIFT           (0)
-struct mpi3_man11_bkplane_spec_vpp_format {
+struct mpi3_man11_bkplane_spec_non_ubm_format {
 	__le16     flags;
-	__le16     reserved02;
+	u8         reserved02;
+	u8         type;
 };
 
-#define MPI3_MAN11_BKPLANE_VPP_FLAGS_REFCLK_POLICY_ALWAYS_ENABLED  (0x0040)
-#define MPI3_MAN11_BKPLANE_VPP_FLAGS_PRESENCE_DETECT_MASK          (0x0030)
-#define MPI3_MAN11_BKPLANE_VPP_FLAGS_PRESENCE_DETECT_GPIO          (0x0000)
-#define MPI3_MAN11_BKPLANE_VPP_FLAGS_PRESENCE_DETECT_REG           (0x0010)
-#define MPI3_MAN11_BKPLANE_VPP_FLAGS_POLL_INTERVAL_MASK            (0x000f)
-#define MPI3_MAN11_BKPLANE_VPP_FLAGS_POLL_INTERVAL_SHIFT           (0)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_GROUP_MASK                    (0xf000)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_GROUP_SHIFT                   (12)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_REFCLK_POLICY_ALWAYS_ENABLED  (0x0200)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_PRESENCE_DETECT_MASK          (0x0030)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_PRESENCE_DETECT_GPIO          (0x0000)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_PRESENCE_DETECT_REG           (0x0010)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_POLL_INTERVAL_MASK            (0x000f)
+#define MPI3_MAN11_BKPLANE_NON_UBM_FLAGS_POLL_INTERVAL_SHIFT           (0)
+#define MPI3_MAN11_BKPLANE_NON_UBM_TYPE_VPP                            (0x00)
 union mpi3_man11_bkplane_spec_format {
-	struct mpi3_man11_bkplane_spec_ubm_format     ubm;
-	struct mpi3_man11_bkplane_spec_vpp_format     vpp;
+	struct mpi3_man11_bkplane_spec_ubm_format         ubm;
+	struct mpi3_man11_bkplane_spec_non_ubm_format     non_ubm;
 };
 
 struct mpi3_man11_bkplane_mgmt_device_format {
 	u8                                        type;
 	u8                                        receptacle_id;
-	__le16                                    reserved02;
+	u8                                        reset_info;
+	u8                                        reserved03;
 	union mpi3_man11_bkplane_spec_format         backplane_mgmt_specific;
 };
 
 #define MPI3_MAN11_BKPLANE_MGMT_TYPE_UBM            (0x00)
-#define MPI3_MAN11_BKPLANE_MGMT_TYPE_VPP            (0x01)
+#define MPI3_MAN11_BKPLANE_MGMT_TYPE_NON_UBM        (0x01)
+#define MPI3_MAN11_BACKPLANE_RESETINFO_ASSERT_TIME_MASK       (0xf0)
+#define MPI3_MAN11_BACKPLANE_RESETINFO_ASSERT_TIME_SHIFT      (4)
+#define MPI3_MAN11_BACKPLANE_RESETINFO_READY_TIME_MASK        (0x0f)
+#define MPI3_MAN11_BACKPLANE_RESETINFO_READY_TIME_SHIFT       (0)
 struct mpi3_man11_gas_gauge_device_format {
 	u8         type;
 	u8         reserved01[3];
@@ -527,6 +568,19 @@
 };
 
 #define MPI3_MAN11_GAS_GAUGE_TYPE_STANDARD          (0x00)
+struct mpi3_man11_mgmt_ctrlr_device_format {
+	__le32     reserved00;
+	__le32     reserved04;
+};
+struct mpi3_man11_board_fan_device_format {
+	u8         flags;
+	u8         reserved01;
+	u8         min_fan_speed;
+	u8         max_fan_speed;
+	__le32     reserved04;
+};
+#define MPI3_MAN11_BOARD_FAN_FLAGS_FAN_CTRLR_TYPE_MASK        (0x07)
+#define MPI3_MAN11_BOARD_FAN_FLAGS_FAN_CTRLR_TYPE_AMC6821     (0x00)
 union mpi3_man11_device_specific_format {
 	struct mpi3_man11_mux_device_format            mux;
 	struct mpi3_man11_temp_sensor_device_format    temp_sensor;
@@ -535,9 +589,10 @@
 	struct mpi3_man11_cable_mgmt_device_format     cable_mgmt;
 	struct mpi3_man11_bkplane_mgmt_device_format   bkplane_mgmt;
 	struct mpi3_man11_gas_gauge_device_format      gas_gauge;
+	struct mpi3_man11_mgmt_ctrlr_device_format     mgmt_controller;
+	struct mpi3_man11_board_fan_device_format      board_fan;
 	__le32                                     words[2];
 };
-
 struct mpi3_man11_istwi_device_format {
 	u8                                     device_type;
 	u8                                     controller;
@@ -556,10 +611,9 @@
 #define MPI3_MAN11_ISTWI_DEVTYPE_CABLE_MGMT           (0x04)
 #define MPI3_MAN11_ISTWI_DEVTYPE_BACKPLANE_MGMT       (0x05)
 #define MPI3_MAN11_ISTWI_DEVTYPE_GAS_GAUGE            (0x06)
+#define MPI3_MAN11_ISTWI_DEVTYPE_MGMT_CONTROLLER      (0x07)
+#define MPI3_MAN11_ISTWI_DEVTYPE_BOARD_FAN            (0x08)
 #define MPI3_MAN11_ISTWI_FLAGS_MUX_PRESENT            (0x01)
-#define MPI3_MAN11_ISTWI_FLAGS_BUS_SPEED_MASK         (0x06)
-#define MPI3_MAN11_ISTWI_FLAGS_BUS_SPEED_100KHZ       (0x00)
-#define MPI3_MAN11_ISTWI_FLAGS_BUS_SPEED_400KHZ       (0x02)
 #ifndef MPI3_MAN11_ISTWI_DEVICE_MAX
 #define MPI3_MAN11_ISTWI_DEVICE_MAX             (1)
 #endif
@@ -680,20 +734,16 @@
 #define MPI3_MAN13_PAGEVERSION                                       (0x00)
 struct mpi3_man_page14 {
 	struct mpi3_config_page_header         header;
-	__le16                             flags;
-	__le16                             reserved0a;
+	__le32                             reserved08;
 	u8                                 num_slot_groups;
 	u8                                 num_slots;
 	__le16                             max_cert_chain_length;
 	__le32                             sealed_slots;
+	__le32                             populated_slots;
+	__le32                             mgmt_pt_updatable_slots;
 };
-
 #define MPI3_MAN14_PAGEVERSION                                       (0x00)
-#define MPI3_MAN14_FLAGS_AUTH_SESSION_REQ                            (0x01)
-#define MPI3_MAN14_FLAGS_AUTH_API_MASK                               (0x0e)
-#define MPI3_MAN14_FLAGS_AUTH_API_NONE                               (0x00)
-#define MPI3_MAN14_FLAGS_AUTH_API_CEREBUS                            (0x02)
-#define MPI3_MAN14_FLAGS_AUTH_API_DMTF_PMCI                          (0x04)
+#define MPI3_MAN14_NUMSLOTS_MAX                                      (32)
 #ifndef MPI3_MAN15_VERSION_RECORD_MAX
 #define MPI3_MAN15_VERSION_RECORD_MAX      1
 #endif
@@ -808,7 +858,7 @@
 	struct mpi3_config_page_header         header;
 	__le32                             flags;
 	u8                                 dmd_io_delay;
-	u8                                 dmd_report_pc_ie;
+	u8                                 dmd_report_pcie;
 	u8                                 dmd_report_sata;
 	u8                                 dmd_report_sas;
 };
@@ -844,26 +894,30 @@
 #define MPI3_IOUNIT2_GPIO_SETTING_ON            (0x0001)
 struct mpi3_io_unit3_sensor {
 	__le16             flags;
-	__le16             reserved02;
-	__le16             threshold[4];
+	u8                 threshold_margin;
+	u8                 reserved03;
+	__le16             threshold[3];
+	__le16             reserved0a;
 	__le32             reserved0c;
 	__le32             reserved10;
 	__le32             reserved14;
 };
 
-#define MPI3_IOUNIT3_SENSOR_FLAGS_T3_ENABLE         (0x0008)
-#define MPI3_IOUNIT3_SENSOR_FLAGS_T2_ENABLE         (0x0004)
-#define MPI3_IOUNIT3_SENSOR_FLAGS_T1_ENABLE         (0x0002)
-#define MPI3_IOUNIT3_SENSOR_FLAGS_T0_ENABLE         (0x0001)
+#define MPI3_IOUNIT3_SENSOR_FLAGS_FATAL_EVENT_ENABLED           (0x0010)
+#define MPI3_IOUNIT3_SENSOR_FLAGS_FATAL_ACTION_ENABLED          (0x0008)
+#define MPI3_IOUNIT3_SENSOR_FLAGS_CRITICAL_EVENT_ENABLED        (0x0004)
+#define MPI3_IOUNIT3_SENSOR_FLAGS_CRITICAL_ACTION_ENABLED       (0x0002)
+#define MPI3_IOUNIT3_SENSOR_FLAGS_WARNING_EVENT_ENABLED         (0x0001)
 #ifndef MPI3_IO_UNIT3_SENSOR_MAX
-#define MPI3_IO_UNIT3_SENSOR_MAX        (1)
+#define MPI3_IO_UNIT3_SENSOR_MAX                                (1)
 #endif
 struct mpi3_io_unit_page3 {
 	struct mpi3_config_page_header         header;
 	__le32                             reserved08;
 	u8                                 num_sensors;
-	u8                                 polling_interval;
-	__le16                             reserved0e;
+	u8                                 nominal_poll_interval;
+	u8                                 warning_poll_interval;
+	u8                                 reserved0f;
 	struct mpi3_io_unit3_sensor            sensor[MPI3_IO_UNIT3_SENSOR_MAX];
 };
 
@@ -873,13 +927,19 @@
 	__le16             reserved02;
 	u8                 flags;
 	u8                 reserved05[3];
-	__le32             reserved08;
+	__le16             istwi_index;
+	u8                 channel;
+	u8                 reserved0b;
 	__le32             reserved0c;
 };
 
+#define MPI3_IOUNIT4_SENSOR_FLAGS_LOC_MASK          (0xe0)
+#define MPI3_IOUNIT4_SENSOR_FLAGS_LOC_SHIFT         (5)
 #define MPI3_IOUNIT4_SENSOR_FLAGS_TEMP_VALID        (0x01)
+#define MPI3_IOUNIT4_SENSOR_ISTWI_INDEX_INTERNAL    (0xffff)
+#define MPI3_IOUNIT4_SENSOR_CHANNEL_RESERVED        (0xff)
 #ifndef MPI3_IO_UNIT4_SENSOR_MAX
-#define MPI3_IO_UNIT4_SENSOR_MAX        (1)
+#define MPI3_IO_UNIT4_SENSOR_MAX                                (1)
 #endif
 struct mpi3_io_unit_page4 {
 	struct mpi3_config_page_header         header;
@@ -906,8 +966,9 @@
 	struct mpi3_io_unit5_spinup_group      spinup_group_parameters[4];
 	__le32                             reserved18;
 	__le32                             reserved1c;
-	__le32                             reserved20;
-	u8                                 reserved24;
+	__le16                             device_shutdown;
+	__le16                             reserved22;
+	u8                                 pcie_device_wait_time;
 	u8                                 sata_device_wait_time;
 	u8                                 spinup_encl_drive_count;
 	u8                                 spinup_encl_delay;
@@ -919,6 +980,22 @@
 };
 
 #define MPI3_IOUNIT5_PAGEVERSION                           (0x00)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_NO_ACTION             (0x00)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_DIRECT_ATTACHED       (0x01)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_EXPANDER_ATTACHED     (0x02)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SWITCH_ATTACHED       (0x02)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_DIRECT_AND_EXPANDER   (0x03)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_DIRECT_AND_SWITCH     (0x03)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SATA_HDD_MASK         (0x0300)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SATA_HDD_SHIFT        (8)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SAS_HDD_MASK          (0x00c0)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SAS_HDD_SHIFT         (6)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_NVME_SSD_MASK         (0x0030)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_NVME_SSD_SHIFT        (4)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SATA_SSD_MASK         (0x000c)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SATA_SSD_SHIFT        (2)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SAS_SSD_MASK          (0x0003)
+#define MPI3_IOUNIT5_DEVICE_SHUTDOWN_SAA_SSD_SHIFT         (0)
 #define MPI3_IOUNIT5_FLAGS_POWER_CAPABLE_SPINUP            (0x02)
 #define MPI3_IOUNIT5_FLAGS_AUTO_PORT_ENABLE                (0x01)
 #define MPI3_IOUNIT5_PHY_SPINUP_GROUP_MASK                 (0x03)
@@ -932,12 +1009,6 @@
 
 #define MPI3_IOUNIT6_PAGEVERSION                (0x00)
 #define MPI3_IOUNIT6_FLAGS_ACT_CABLE_PWR_EXC    (0x01)
-struct mpi3_io_unit_page7 {
-	struct mpi3_config_page_header         header;
-	__le32                             reserved08;
-};
-
-#define MPI3_IOUNIT7_PAGEVERSION                (0x00)
 #ifndef MPI3_IOUNIT8_DIGEST_MAX
 #define MPI3_IOUNIT8_DIGEST_MAX                   (1)
 #endif
@@ -977,6 +1048,48 @@
 #define MPI3_IOUNIT9_PAGEVERSION                  (0x00)
 #define MPI3_IOUNIT9_FLAGS_VDFIRST_ENABLED         (0x01)
 #define MPI3_IOUNIT9_FIRSTDEVICE_UNKNOWN          (0xffff)
+struct mpi3_io_unit_page10 {
+	struct mpi3_config_page_header         header;
+	u8                                 flags;
+	u8                                 reserved09[3];
+	__le32                             silicon_id;
+	u8                                 fw_version_minor;
+	u8                                 fw_version_major;
+	u8                                 hw_version_minor;
+	u8                                 hw_version_major;
+	u8                                 part_number[16];
+};
+#define MPI3_IOUNIT10_PAGEVERSION                  (0x00)
+#define MPI3_IOUNIT10_FLAGS_VALID                  (0x01)
+#define MPI3_IOUNIT10_FLAGS_ACTIVEID_MASK          (0x02)
+#define MPI3_IOUNIT10_FLAGS_ACTIVEID_FIRST_REGION  (0x00)
+#define MPI3_IOUNIT10_FLAGS_ACTIVEID_SECOND_REGION (0x02)
+#define MPI3_IOUNIT10_FLAGS_PBLP_EXPECTED          (0x80)
+#ifndef MPI3_IOUNIT11_PROFILE_MAX
+#define MPI3_IOUNIT11_PROFILE_MAX                   (1)
+#endif
+struct mpi3_iounit11_profile {
+	u8                                 profile_identifier;
+	u8                                 reserved01[3];
+	__le16                             max_vds;
+	__le16                             max_host_pds;
+	__le16                             max_adv_host_pds;
+	__le16                             max_raid_pds;
+	__le16                             max_nvme;
+	__le16                             max_outstanding_requests;
+	__le16                             subsystem_id;
+	__le16                             reserved12;
+	__le32                             reserved14[2];
+};
+struct mpi3_io_unit_page11 {
+	struct mpi3_config_page_header         header;
+	__le32                             reserved08;
+	u8                                 num_profiles;
+	u8                                 current_profile_identifier;
+	__le16                             reserved0e;
+	struct mpi3_iounit11_profile           profile[MPI3_IOUNIT11_PROFILE_MAX];
+};
+#define MPI3_IOUNIT11_PAGEVERSION                  (0x00)
 struct mpi3_ioc_page0 {
 	struct mpi3_config_page_header         header;
 	__le32                             reserved08;
@@ -994,12 +1107,10 @@
 	struct mpi3_config_page_header         header;
 	__le32                             coalescing_timeout;
 	u8                                 coalescing_depth;
-	u8                                 pci_slot_num;
+	u8                                 obsolete;
 	__le16                             reserved0e;
 };
-
 #define MPI3_IOC1_PAGEVERSION               (0x00)
-#define MPI3_IOC1_PCISLOTNUM_UNKNOWN        (0xff)
 #ifndef MPI3_IOC2_EVENTMASK_WORDS
 #define MPI3_IOC2_EVENTMASK_WORDS           (4)
 #endif
@@ -1012,7 +1123,52 @@
 };
 
 #define MPI3_IOC2_PAGEVERSION               (0x00)
-struct mpi3_uefibsd_page0 {
+#define MPI3_DRIVER_FLAGS_ADMINRAIDPD_BLOCKED               (0x0010)
+#define MPI3_DRIVER_FLAGS_OOBRAIDPD_BLOCKED                 (0x0008)
+#define MPI3_DRIVER_FLAGS_OOBRAIDVD_BLOCKED                 (0x0004)
+#define MPI3_DRIVER_FLAGS_OOBADVHOSTPD_BLOCKED              (0x0002)
+#define MPI3_DRIVER_FLAGS_OOBHOSTPD_BLOCKED                 (0x0001)
+struct mpi3_allowed_cmd_scsi {
+	__le16                             service_action;
+	u8                                 operation_code;
+	u8                                 command_flags;
+};
+
+struct mpi3_allowed_cmd_ata {
+	u8                                 subcommand;
+	u8                                 reserved01;
+	u8                                 command;
+	u8                                 command_flags;
+};
+
+struct mpi3_allowed_cmd_nvme {
+	u8                                 reserved00;
+	u8                                 nvme_cmd_flags;
+	u8                                 op_code;
+	u8                                 command_flags;
+};
+
+#define MPI3_DRIVER_ALLOWEDCMD_NVMECMDFLAGS_SUBQ_TYPE_MASK     (0x80)
+#define MPI3_DRIVER_ALLOWEDCMD_NVMECMDFLAGS_SUBQ_TYPE_IO       (0x00)
+#define MPI3_DRIVER_ALLOWEDCMD_NVMECMDFLAGS_SUBQ_TYPE_ADMIN    (0x80)
+#define MPI3_DRIVER_ALLOWEDCMD_NVMECMDFLAGS_CMDSET_MASK        (0x3f)
+#define MPI3_DRIVER_ALLOWEDCMD_NVMECMDFLAGS_CMDSET_NVM         (0x00)
+union mpi3_allowed_cmd {
+	struct mpi3_allowed_cmd_scsi           scsi;
+	struct mpi3_allowed_cmd_ata            ata;
+	struct mpi3_allowed_cmd_nvme           nvme;
+};
+
+#define MPI3_DRIVER_ALLOWEDCMD_CMDFLAGS_ADMINRAIDPD_BLOCKED    (0x20)
+#define MPI3_DRIVER_ALLOWEDCMD_CMDFLAGS_OOBRAIDPD_BLOCKED      (0x10)
+#define MPI3_DRIVER_ALLOWEDCMD_CMDFLAGS_OOBRAIDVD_BLOCKED      (0x08)
+#define MPI3_DRIVER_ALLOWEDCMD_CMDFLAGS_OOBADVHOSTPD_BLOCKED   (0x04)
+#define MPI3_DRIVER_ALLOWEDCMD_CMDFLAGS_OOBHOSTPD_BLOCKED      (0x02)
+#define MPI3_DRIVER_ALLOWEDCMD_CMDFLAGS_CHECKSUBCMD_ENABLED    (0x01)
+#ifndef MPI3_ALLOWED_CMDS_MAX
+#define MPI3_ALLOWED_CMDS_MAX           (1)
+#endif
+struct mpi3_driver_page0 {
 	struct mpi3_config_page_header         header;
 	__le32                             bsd_options;
 	u8                                 ssu_timeout;
@@ -1025,14 +1181,121 @@
 	__le32                             reserved14;
 	__le32                             reserved18;
 };
+#define MPI3_DRIVER0_PAGEVERSION               (0x00)
+#define MPI3_DRIVER0_BSDOPTS_DIS_HII_CONFIG_UTIL            (0x00000004)
+#define MPI3_DRIVER0_BSDOPTS_REGISTRATION_MASK              (0x00000003)
+#define MPI3_DRIVER0_BSDOPTS_REGISTRATION_IOC_AND_DEVS      (0x00000000)
+#define MPI3_DRIVER0_BSDOPTS_REGISTRATION_IOC_ONLY          (0x00000001)
+struct mpi3_driver_page1 {
+	struct mpi3_config_page_header         header;
+	__le32                             flags;
+	__le32                             reserved0c;
+	__le16                             host_diag_trace_max_size;
+	__le16                             host_diag_trace_min_size;
+	__le16                             host_diag_trace_decrement_size;
+	__le16                             reserved16;
+	__le16                             host_diag_fw_max_size;
+	__le16                             host_diag_fw_min_size;
+	__le16                             host_diag_fw_decrement_size;
+	__le16                             reserved1e;
+	__le16                             host_diag_driver_max_size;
+	__le16                             host_diag_driver_min_size;
+	__le16                             host_diag_driver_decrement_size;
+	__le16                             reserved26;
+};
+
+#define MPI3_DRIVER1_PAGEVERSION               (0x00)
+#ifndef MPI3_DRIVER2_TRIGGER_MAX
+#define MPI3_DRIVER2_TRIGGER_MAX           (1)
+#endif
+struct mpi3_driver2_trigger_event {
+	u8                                 type;
+	u8                                 flags;
+	u8                                 reserved02;
+	u8                                 event;
+	__le32                             reserved04[3];
+};
+
+struct mpi3_driver2_trigger_scsi_sense {
+	u8                                 type;
+	u8                                 flags;
+	__le16                             reserved02;
+	u8                                 ascq;
+	u8                                 asc;
+	u8                                 sense_key;
+	u8                                 reserved07;
+	__le32                             reserved08[2];
+};
+
+#define MPI3_DRIVER2_TRIGGER_SCSI_SENSE_ASCQ_MATCH_ALL                        (0xff)
+#define MPI3_DRIVER2_TRIGGER_SCSI_SENSE_ASC_MATCH_ALL                         (0xff)
+#define MPI3_DRIVER2_TRIGGER_SCSI_SENSE_SENSE_KEY_MATCH_ALL                   (0xff)
+struct mpi3_driver2_trigger_reply {
+	u8                                 type;
+	u8                                 flags;
+	__le16                             ioc_status;
+	__le32                             ioc_log_info;
+	__le32                             ioc_log_info_mask;
+	__le32                             reserved0c;
+};
+
+#define MPI3_DRIVER2_TRIGGER_REPLY_IOCSTATUS_MATCH_ALL                        (0xffff)
+union mpi3_driver2_trigger_element {
+	struct mpi3_driver2_trigger_event             event;
+	struct mpi3_driver2_trigger_scsi_sense        scsi_sense;
+	struct mpi3_driver2_trigger_reply             reply;
+};
+
+#define MPI3_DRIVER2_TRIGGER_TYPE_EVENT                                       (0x00)
+#define MPI3_DRIVER2_TRIGGER_TYPE_SCSI_SENSE                                  (0x01)
+#define MPI3_DRIVER2_TRIGGER_TYPE_REPLY                                       (0x02)
+#define MPI3_DRIVER2_TRIGGER_FLAGS_DIAG_TRACE_RELEASE                         (0x02)
+#define MPI3_DRIVER2_TRIGGER_FLAGS_DIAG_FW_RELEASE                            (0x01)
+struct mpi3_driver_page2 {
+	struct mpi3_config_page_header         header;
+	__le64                             master_trigger;
+	__le32                             reserved10[3];
+	u8                                 num_triggers;
+	u8                                 reserved1d[3];
+	union mpi3_driver2_trigger_element    trigger[MPI3_DRIVER2_TRIGGER_MAX];
+};
 
-#define MPI3_UEFIBSD_PAGEVERSION               (0x00)
-#define MPI3_UEFIBSD_BSDOPTS_REGISTRATION_MASK              (0x00000003)
-#define MPI3_UEFIBSD_BSDOPTS_REGISTRATION_IOC_AND_DEVS      (0x00000000)
-#define MPI3_UEFIBSD_BSDOPTS_REGISTRATION_IOC_ONLY          (0x00000001)
-#define MPI3_UEFIBSD_BSDOPTS_REGISTRATION_NONE              (0x00000002)
-#define MPI3_UEFIBSD_BSDOPTS_DIS_HII_CONFIG_UTIL            (0x00000004)
-#define MPI3_UEFIBSD_BSDOPTS_EN_ADV_ADAPTER_CONFIG          (0x00000008)
+#define MPI3_DRIVER2_PAGEVERSION               (0x00)
+#define MPI3_DRIVER2_MASTERTRIGGER_DIAG_TRACE_RELEASE                       (0x8000000000000000ULL)
+#define MPI3_DRIVER2_MASTERTRIGGER_DIAG_FW_RELEASE                          (0x4000000000000000ULL)
+#define MPI3_DRIVER2_MASTERTRIGGER_SNAPDUMP                                 (0x2000000000000000ULL)
+#define MPI3_DRIVER2_MASTERTRIGGER_DEVICE_REMOVAL_ENABLED                   (0x0000000000000004ULL)
+#define MPI3_DRIVER2_MASTERTRIGGER_TASK_MANAGEMENT_ENABLED                  (0x0000000000000002ULL)
+struct mpi3_driver_page10 {
+	struct mpi3_config_page_header         header;
+	__le16                             flags;
+	__le16                             reserved0a;
+	u8                                 num_allowed_commands;
+	u8                                 reserved0d[3];
+	union mpi3_allowed_cmd                allowed_command[MPI3_ALLOWED_CMDS_MAX];
+};
+
+#define MPI3_DRIVER10_PAGEVERSION               (0x00)
+struct mpi3_driver_page20 {
+	struct mpi3_config_page_header         header;
+	__le16                             flags;
+	__le16                             reserved0a;
+	u8                                 num_allowed_commands;
+	u8                                 reserved0d[3];
+	union mpi3_allowed_cmd                allowed_command[MPI3_ALLOWED_CMDS_MAX];
+};
+
+#define MPI3_DRIVER20_PAGEVERSION               (0x00)
+struct mpi3_driver_page30 {
+	struct mpi3_config_page_header         header;
+	__le16                             flags;
+	__le16                             reserved0a;
+	u8                                 num_allowed_commands;
+	u8                                 reserved0d[3];
+	union mpi3_allowed_cmd                allowed_command[MPI3_ALLOWED_CMDS_MAX];
+};
+
+#define MPI3_DRIVER30_PAGEVERSION               (0x00)
 union mpi3_security_mac {
 	__le32                             dword[16];
 	__le16                             word[32];
@@ -1102,7 +1365,7 @@
 #define MPI3_SECURITY1_KEY_RECORD_CONSUMER_NOT_VALID         (0x00)
 #define MPI3_SECURITY1_KEY_RECORD_CONSUMER_SAFESTORE         (0x01)
 #define MPI3_SECURITY1_KEY_RECORD_CONSUMER_CERT_CHAIN        (0x02)
-#define MPI3_SECURITY1_KEY_RECORD_CONSUMER_AUTH_DEV_KEY      (0x03)
+#define MPI3_SECURITY1_KEY_RECORD_CONSUMER_DEVICE_KEY        (0x03)
 #define MPI3_SECURITY1_KEY_RECORD_CONSUMER_CACHE_OFFLOAD     (0x04)
 struct mpi3_security_page1 {
 	struct mpi3_config_page_header         header;
@@ -1137,16 +1400,30 @@
 	struct mpi3_config_page_header         header;
 	__le32                             reserved08;
 	u8                                 num_phys;
-	u8                                 reserved0d[3];
+	u8                                 init_status;
+	__le16                             reserved0e;
 	struct mpi3_sas_io_unit0_phy_data      phy_data[MPI3_SAS_IO_UNIT0_PHY_MAX];
 };
 
-#define MPI3_SASIOUNIT0_PAGEVERSION                         (0x00)
-#define MPI3_SASIOUNIT0_PORTFLAGS_DISC_IN_PROGRESS          (0x08)
-#define MPI3_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG          (0x01)
-#define MPI3_SASIOUNIT0_PHYFLAGS_INIT_PERSIST_CONNECT       (0x40)
-#define MPI3_SASIOUNIT0_PHYFLAGS_TARG_PERSIST_CONNECT       (0x20)
-#define MPI3_SASIOUNIT0_PHYFLAGS_PHY_DISABLED               (0x08)
+#define MPI3_SASIOUNIT0_PAGEVERSION                          (0x00)
+#define MPI3_SASIOUNIT0_INITSTATUS_NO_ERRORS                 (0x00)
+#define MPI3_SASIOUNIT0_INITSTATUS_NEEDS_INITIALIZATION      (0x01)
+#define MPI3_SASIOUNIT0_INITSTATUS_NO_TARGETS_ALLOCATED      (0x02)
+#define MPI3_SASIOUNIT0_INITSTATUS_BAD_NUM_PHYS              (0x04)
+#define MPI3_SASIOUNIT0_INITSTATUS_UNSUPPORTED_CONFIG        (0x05)
+#define MPI3_SASIOUNIT0_INITSTATUS_HOST_PHYS_ENABLED         (0x06)
+#define MPI3_SASIOUNIT0_INITSTATUS_PRODUCT_SPECIFIC_MIN      (0xf0)
+#define MPI3_SASIOUNIT0_INITSTATUS_PRODUCT_SPECIFIC_MAX      (0xff)
+#define MPI3_SASIOUNIT0_PORTFLAGS_DISC_IN_PROGRESS           (0x08)
+#define MPI3_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG_MASK      (0x03)
+#define MPI3_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG_IOUNIT1   (0x00)
+#define MPI3_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG_DYNAMIC   (0x01)
+#define MPI3_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG_BACKPLANE (0x02)
+#define MPI3_SASIOUNIT0_PHYFLAGS_INIT_PERSIST_CONNECT        (0x40)
+#define MPI3_SASIOUNIT0_PHYFLAGS_TARG_PERSIST_CONNECT        (0x20)
+#define MPI3_SASIOUNIT0_PHYFLAGS_PHY_DISABLED                (0x08)
+#define MPI3_SASIOUNIT0_PHYFLAGS_VIRTUAL_PHY                 (0x02)
+#define MPI3_SASIOUNIT0_PHYFLAGS_HOST_PHY                    (0x01)
 struct mpi3_sas_io_unit1_phy_data {
 	u8                 io_unit_port;
 	u8                 port_flags;
@@ -1343,6 +1620,26 @@
 #define MPI3_SASEXPANDER1_DISCINFO_BAD_PHY_DISABLED     (0x04)
 #define MPI3_SASEXPANDER1_DISCINFO_LINK_STATUS_CHANGE   (0x02)
 #define MPI3_SASEXPANDER1_DISCINFO_NO_ROUTING_ENTRIES   (0x01)
+#ifndef MPI3_SASEXPANDER2_MAX_NUM_PHYS
+#define MPI3_SASEXPANDER2_MAX_NUM_PHYS                               (1)
+#endif
+struct mpi3_sasexpander2_phy_element {
+	u8                                 link_change_count;
+	u8                                 reserved01;
+	__le16                             rate_change_count;
+	__le32                             reserved04;
+};
+
+struct mpi3_sas_expander_page2 {
+	struct mpi3_config_page_header         header;
+	u8                                 num_phys;
+	u8                                 reserved09;
+	__le16                             dev_handle;
+	__le32                             reserved0c;
+	struct mpi3_sasexpander2_phy_element   phy[MPI3_SASEXPANDER2_MAX_NUM_PHYS];
+};
+
+#define MPI3_SASEXPANDER2_PAGEVERSION                   (0x00)
 struct mpi3_sas_port_page0 {
 	struct mpi3_config_page_header         header;
 	u8                                 port_number;
@@ -1510,6 +1807,14 @@
 #define MPI3_PCIE_NEG_LINK_RATE_8_0                     (0x04)
 #define MPI3_PCIE_NEG_LINK_RATE_16_0                    (0x05)
 #define MPI3_PCIE_NEG_LINK_RATE_32_0                    (0x06)
+#define MPI3_PCIE_ASPM_ENABLE_NONE                      (0x0)
+#define MPI3_PCIE_ASPM_ENABLE_L0S                       (0x1)
+#define MPI3_PCIE_ASPM_ENABLE_L1                        (0x2)
+#define MPI3_PCIE_ASPM_ENABLE_L0S_L1                    (0x3)
+#define MPI3_PCIE_ASPM_SUPPORT_NONE                     (0x0)
+#define MPI3_PCIE_ASPM_SUPPORT_L0S                      (0x1)
+#define MPI3_PCIE_ASPM_SUPPORT_L1                       (0x2)
+#define MPI3_PCIE_ASPM_SUPPORT_L0S_L1                   (0x3)
 struct mpi3_pcie_io_unit0_phy_data {
 	u8         link;
 	u8         link_flags;
@@ -1540,7 +1845,8 @@
 	__le32                             reserved08;
 	u8                                 num_phys;
 	u8                                 init_status;
-	__le16                             reserved0e;
+	u8                                 aspm;
+	u8                                 reserved0f;
 	struct mpi3_pcie_io_unit0_phy_data     phy_data[MPI3_PCIE_IO_UNIT0_PHY_MAX];
 };
 
@@ -1556,6 +1862,14 @@
 #define MPI3_PCIEIOUNIT0_INITSTATUS_BAD_CLOCKING_MODE       (0x08)
 #define MPI3_PCIEIOUNIT0_INITSTATUS_PROD_SPEC_START         (0xf0)
 #define MPI3_PCIEIOUNIT0_INITSTATUS_PROD_SPEC_END           (0xff)
+#define MPI3_PCIEIOUNIT0_ASPM_SWITCH_STATES_MASK            (0xc0)
+#define MPI3_PCIEIOUNIT0_ASPM_SWITCH_STATES_SHIFT              (6)
+#define MPI3_PCIEIOUNIT0_ASPM_DIRECT_STATES_MASK            (0x30)
+#define MPI3_PCIEIOUNIT0_ASPM_DIRECT_STATES_SHIFT              (4)
+#define MPI3_PCIEIOUNIT0_ASPM_SWITCH_SUPPORT_MASK           (0x0c)
+#define MPI3_PCIEIOUNIT0_ASPM_SWITCH_SUPPORT_SHIFT             (2)
+#define MPI3_PCIEIOUNIT0_ASPM_DIRECT_SUPPORT_MASK           (0x03)
+#define MPI3_PCIEIOUNIT0_ASPM_DIRECT_SUPPORT_SHIFT             (0)
 struct mpi3_pcie_io_unit1_phy_data {
 	u8         link;
 	u8         link_flags;
@@ -1569,16 +1883,16 @@
 #define MPI3_PCIEIOUNIT1_LINKFLAGS_PCIE_CLK_MODE_DIS_SEPARATE_REFCLK      (0x00)
 #define MPI3_PCIEIOUNIT1_LINKFLAGS_PCIE_CLK_MODE_EN_SRIS                  (0x01)
 #define MPI3_PCIEIOUNIT1_LINKFLAGS_PCIE_CLK_MODE_EN_SRNS                  (0x02)
-#define MPI3_PCIEIOUNIT1_PHYFLAGS_PHY_DISABLE               (0x08)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_MASK                      (0xf0)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_SHIFT                     (4)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_2_5                       (0x20)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_5_0                       (0x30)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_8_0                       (0x40)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_16_0                      (0x50)
-#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_32_0                      (0x60)
+#define MPI3_PCIEIOUNIT1_PHYFLAGS_PHY_DISABLE                             (0x08)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_MASK                               (0xf0)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_SHIFT                                 (4)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_2_5                                (0x20)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_5_0                                (0x30)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_8_0                                (0x40)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_16_0                               (0x50)
+#define MPI3_PCIEIOUNIT1_MMLR_MAX_RATE_32_0                               (0x60)
 #ifndef MPI3_PCIE_IO_UNIT1_PHY_MAX
-#define MPI3_PCIE_IO_UNIT1_PHY_MAX          (1)
+#define MPI3_PCIE_IO_UNIT1_PHY_MAX                                           (1)
 #endif
 struct mpi3_pcie_io_unit_page1 {
 	struct mpi3_config_page_header         header;
@@ -1586,21 +1900,66 @@
 	__le32                             reserved0c;
 	u8                                 num_phys;
 	u8                                 reserved11;
-	__le16                             reserved12;
+	u8                                 aspm;
+	u8                                 reserved13;
 	struct mpi3_pcie_io_unit1_phy_data     phy_data[MPI3_PCIE_IO_UNIT1_PHY_MAX];
 };
 
-#define MPI3_PCIEIOUNIT1_PAGEVERSION                        (0x00)
+#define MPI3_PCIEIOUNIT1_PAGEVERSION                                           (0x00)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_OVERRIDE_DISABLE                   (0x80)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_CLOCK_OVERRIDE_DISABLE                  (0x40)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_CLOCK_OVERRIDE_MODE_MASK                (0x30)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_CLOCK_OVERRIDE_MODE_SHIFT               (4)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_CLOCK_OVERRIDE_MODE_SRIS_SRNS_DISABLED  (0x00)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_CLOCK_OVERRIDE_MODE_SRIS_ENABLED        (0x10)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_CLOCK_OVERRIDE_MODE_SRNS_ENABLED        (0x20)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_RATE_OVERRIDE_MASK                 (0x0f)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_RATE_OVERRIDE_MAX_2_5              (0x02)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_RATE_OVERRIDE_MAX_5_0              (0x03)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_RATE_OVERRIDE_MAX_8_0              (0x04)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_RATE_OVERRIDE_MAX_16_0             (0x05)
+#define MPI3_PCIEIOUNIT1_CONTROL_FLAGS_LINK_RATE_OVERRIDE_MAX_32_0             (0x06)
+#define MPI3_PCIEIOUNIT1_ASPM_SWITCH_MASK                                 (0x0c)
+#define MPI3_PCIEIOUNIT1_ASPM_SWITCH_SHIFT                                   (2)
+#define MPI3_PCIEIOUNIT1_ASPM_DIRECT_MASK                                 (0x03)
+#define MPI3_PCIEIOUNIT1_ASPM_DIRECT_SHIFT                                   (0)
 struct mpi3_pcie_io_unit_page2 {
 	struct mpi3_config_page_header         header;
-	__le16                             nv_me_max_queue_depth;
-	__le16                             reserved0a;
-	u8                                 nv_me_abort_to;
+	__le16                             nvme_max_q_dx1;
+	__le16                             nvme_max_q_dx2;
+	u8                                 nvme_abort_to;
 	u8                                 reserved0d;
-	__le16                             reserved0e;
+	__le16                             nvme_max_q_dx4;
 };
 
 #define MPI3_PCIEIOUNIT2_PAGEVERSION                        (0x00)
+#define MPI3_PCIEIOUNIT3_ERROR_RECEIVER_ERROR               (0)
+#define MPI3_PCIEIOUNIT3_ERROR_RECOVERY                     (1)
+#define MPI3_PCIEIOUNIT3_ERROR_CORRECTABLE_ERROR_MSG        (2)
+#define MPI3_PCIEIOUNIT3_ERROR_BAD_DLLP                     (3)
+#define MPI3_PCIEIOUNIT3_ERROR_BAD_TLP                      (4)
+#define MPI3_PCIEIOUNIT3_NUM_ERROR_INDEX                    (5)
+struct mpi3_pcie_io_unit3_error {
+	__le16                             threshold_count;
+	__le16                             reserved02;
+};
+
+struct mpi3_pcie_io_unit_page3 {
+	struct mpi3_config_page_header         header;
+	u8                                 threshold_window;
+	u8                                 threshold_action;
+	u8                                 escalation_count;
+	u8                                 escalation_action;
+	u8                                 num_errors;
+	u8                                 reserved0d[3];
+	struct mpi3_pcie_io_unit3_error        error[MPI3_PCIEIOUNIT3_NUM_ERROR_INDEX];
+};
+
+#define MPI3_PCIEIOUNIT3_PAGEVERSION                        (0x00)
+#define MPI3_PCIEIOUNIT3_ACTION_NO_ACTION                   (0x00)
+#define MPI3_PCIEIOUNIT3_ACTION_HOT_RESET                   (0x01)
+#define MPI3_PCIEIOUNIT3_ACTION_REDUCE_LINK_RATE_ONLY       (0x02)
+#define MPI3_PCIEIOUNIT3_ACTION_REDUCE_LINK_RATE_NO_ACCESS  (0x03)
 struct mpi3_pcie_switch_page0 {
 	struct mpi3_config_page_header     header;
 	u8                             io_unit_port;
@@ -1609,7 +1968,7 @@
 	__le16                         dev_handle;
 	__le16                         parent_dev_handle;
 	u8                             num_ports;
-	u8                             pc_ie_level;
+	u8                             pcie_level;
 	__le16                         reserved12;
 	__le32                         reserved14;
 	__le32                         reserved18;
@@ -1623,7 +1982,8 @@
 struct mpi3_pcie_switch_page1 {
 	struct mpi3_config_page_header     header;
 	u8                             io_unit_port;
-	u8                             reserved09[3];
+	u8                             flags;
+	__le16                         reserved0a;
 	u8                             num_ports;
 	u8                             port_num;
 	__le16                         attached_dev_handle;
@@ -1636,15 +1996,43 @@
 };
 
 #define MPI3_PCIESWITCH1_PAGEVERSION        (0x00)
+#define MPI3_PCIESWITCH1_FLAGS_ASPMSTATE_MASK     (0x0c)
+#define MPI3_PCIESWITCH1_FLAGS_ASPMSTATE_SHIFT    (2)
+#define MPI3_PCIESWITCH1_FLAGS_ASPMSUPPORT_MASK     (0x03)
+#define MPI3_PCIESWITCH1_FLAGS_ASPMSUPPORT_SHIFT    (0)
+#ifndef MPI3_PCIESWITCH2_MAX_NUM_PORTS
+#define MPI3_PCIESWITCH2_MAX_NUM_PORTS                               (1)
+#endif
+struct mpi3_pcieswitch2_port_element {
+	__le16                             link_change_count;
+	__le16                             rate_change_count;
+	__le32                             reserved04;
+};
+
+struct mpi3_pcie_switch_page2 {
+	struct mpi3_config_page_header         header;
+	u8                                 num_ports;
+	u8                                 reserved09;
+	__le16                             dev_handle;
+	__le32                             reserved0c;
+	struct mpi3_pcieswitch2_port_element   port[MPI3_PCIESWITCH2_MAX_NUM_PORTS];
+};
+
+#define MPI3_PCIESWITCH2_PAGEVERSION        (0x00)
 struct mpi3_pcie_link_page0 {
 	struct mpi3_config_page_header     header;
 	u8                             link;
 	u8                             reserved09[3];
-	__le32                         correctable_error_count;
-	__le16                         n_fatal_error_count;
-	__le16                         reserved12;
-	__le16                         fatal_error_count;
-	__le16                         reserved16;
+	__le32                         reserved0c;
+	__le32                         receiver_error_count;
+	__le32                         recovery_count;
+	__le32                         corr_error_msg_count;
+	__le32                         non_fatal_error_msg_count;
+	__le32                         fatal_error_msg_count;
+	__le32                         non_fatal_error_count;
+	__le32                         fatal_error_count;
+	__le32                         bad_dllp_count;
+	__le32                         bad_tlp_count;
 };
 
 #define MPI3_PCIELINK0_PAGEVERSION          (0x00)
@@ -1654,11 +2042,12 @@
 	__le16                             flags;
 	__le16                             enclosure_handle;
 	__le16                             num_slots;
-	__le16                             start_slot;
+	__le16                             reserved16;
 	u8                                 io_unit_port;
 	u8                                 enclosure_level;
 	__le16                             sep_dev_handle;
-	__le32                             reserved1c;
+	u8                                 chassis_slot;
+	u8                                 reserved1d[3];
 };
 
 #define MPI3_ENCLOSURE0_PAGEVERSION                     (0x00)
@@ -1666,6 +2055,7 @@
 #define MPI3_ENCLS0_FLAGS_ENCL_TYPE_VIRTUAL             (0x0000)
 #define MPI3_ENCLS0_FLAGS_ENCL_TYPE_SAS                 (0x4000)
 #define MPI3_ENCLS0_FLAGS_ENCL_TYPE_PCIE                (0x8000)
+#define MPI3_ENCLS0_FLAGS_CHASSIS_SLOT_VALID            (0x0020)
 #define MPI3_ENCLS0_FLAGS_ENCL_DEV_PRESENT_MASK         (0x0010)
 #define MPI3_ENCLS0_FLAGS_ENCL_DEV_NOT_FOUND            (0x0000)
 #define MPI3_ENCLS0_FLAGS_ENCL_DEV_PRESENT              (0x0010)
@@ -1686,6 +2076,7 @@
 	u8         zone_group;
 };
 
+#define MPI3_DEVICE0_SASSATA_FLAGS_WRITE_SAME_UNMAP_NCQ (0x0400)
 #define MPI3_DEVICE0_SASSATA_FLAGS_SLUMBER_CAP          (0x0200)
 #define MPI3_DEVICE0_SASSATA_FLAGS_PARTIAL_CAP          (0x0100)
 #define MPI3_DEVICE0_SASSATA_FLAGS_ASYNC_NOTIFY         (0x0080)
@@ -1707,10 +2098,11 @@
 	__le32     maximum_data_transfer_size;
 	__le32     capabilities;
 	__le16     noiob;
-	u8         nv_me_abort_to;
+	u8         nvme_abort_to;
 	u8         page_size;
 	__le16     shutdown_latency;
-	__le16     reserved16;
+	u8         recovery_info;
+	u8         reserved17;
 };
 
 #define MPI3_DEVICE0_PCIE_LINK_RATE_32_0_SUPP           (0x10)
@@ -1718,25 +2110,48 @@
 #define MPI3_DEVICE0_PCIE_LINK_RATE_8_0_SUPP            (0x04)
 #define MPI3_DEVICE0_PCIE_LINK_RATE_5_0_SUPP            (0x02)
 #define MPI3_DEVICE0_PCIE_LINK_RATE_2_5_SUPP            (0x01)
-#define MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK             (0x0003)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK             (0x0007)
 #define MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_NO_DEVICE        (0x0000)
 #define MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_NVME_DEVICE      (0x0001)
 #define MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SWITCH_DEVICE    (0x0002)
 #define MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SCSI_DEVICE      (0x0003)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_ASPM_MASK             (0x0030)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_ASPM_SHIFT            (4)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_PITYPE_MASK           (0x00c0)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_PITYPE_SHIFT          (6)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_PITYPE_0              (0x0000)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_PITYPE_1              (0x0040)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_PITYPE_2              (0x0080)
+#define MPI3_DEVICE0_PCIE_DEVICE_INFO_PITYPE_3              (0x00c0)
+#define MPI3_DEVICE0_PCIE_CAP_SGL_EXTRA_LENGTH_SUPPORTED    (0x00000020)
 #define MPI3_DEVICE0_PCIE_CAP_METADATA_SEPARATED            (0x00000010)
 #define MPI3_DEVICE0_PCIE_CAP_SGL_DWORD_ALIGN_REQUIRED      (0x00000008)
-#define MPI3_DEVICE0_PCIE_CAP_NVME_SGL_ENABLED              (0x00000004)
+#define MPI3_DEVICE0_PCIE_CAP_SGL_FORMAT_SGL                (0x00000004)
+#define MPI3_DEVICE0_PCIE_CAP_SGL_FORMAT_PRP                (0x00000000)
 #define MPI3_DEVICE0_PCIE_CAP_BIT_BUCKET_SGL_SUPP           (0x00000002)
 #define MPI3_DEVICE0_PCIE_CAP_SGL_SUPP                      (0x00000001)
+#define MPI3_DEVICE0_PCIE_CAP_ASPM_MASK                     (0x000000c0)
+#define MPI3_DEVICE0_PCIE_CAP_ASPM_SHIFT                    (6)
+#define MPI3_DEVICE0_PCIE_RECOVER_METHOD_MASK               (0xe0)
+#define MPI3_DEVICE0_PCIE_RECOVER_METHOD_NS_MGMT            (0x00)
+#define MPI3_DEVICE0_PCIE_RECOVER_METHOD_FORMAT             (0x20)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_MASK               (0x1f)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_NO_NS              (0x00)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_NO_NSID_1          (0x01)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_TOO_MANY_NS        (0x02)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_PROTECTION         (0x03)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_METADATA_SZ        (0x04)
+#define MPI3_DEVICE0_PCIE_RECOVER_REASON_LBA_DATA_SZ        (0x05)
 struct mpi3_device0_vd_format {
 	u8         vd_state;
 	u8         raid_level;
 	__le16     device_info;
 	__le16     flags;
-	__le16     reserved06;
-	__le32     reserved08[2];
+	__le16     io_throttle_group;
+	__le16     io_throttle_group_low;
+	__le16     io_throttle_group_high;
+	__le32     reserved0c;
 };
-
 #define MPI3_DEVICE0_VD_STATE_OFFLINE                       (0x00)
 #define MPI3_DEVICE0_VD_STATE_PARTIALLY_DEGRADED            (0x01)
 #define MPI3_DEVICE0_VD_STATE_DEGRADED                      (0x02)
@@ -1753,6 +2168,7 @@
 #define MPI3_DEVICE0_VD_DEVICE_INFO_NVME                    (0x0004)
 #define MPI3_DEVICE0_VD_DEVICE_INFO_SATA                    (0x0002)
 #define MPI3_DEVICE0_VD_DEVICE_INFO_SAS                     (0x0001)
+#define MPI3_DEVICE0_VD_FLAGS_IO_THROTTLE_GROUP_QD_MASK     (0xf000)
 #define MPI3_DEVICE0_VD_FLAGS_METADATA_MODE_MASK            (0x0003)
 #define MPI3_DEVICE0_VD_FLAGS_METADATA_MODE_NONE            (0x0000)
 #define MPI3_DEVICE0_VD_FLAGS_METADATA_MODE_HOST            (0x0001)
@@ -1783,6 +2199,8 @@
 };
 
 #define MPI3_DEVICE0_PAGEVERSION                        (0x00)
+#define MPI3_DEVICE0_PARENT_INVALID                     (0xffff)
+#define MPI3_DEVICE0_ENCLOSURE_HANDLE_NO_ENCLOSURE      (0x0000)
 #define MPI3_DEVICE0_WWID_INVALID                       (0xffffffffffffffff)
 #define MPI3_DEVICE0_PERSISTENTID_INVALID               (0xffff)
 #define MPI3_DEVICE0_IOUNITPORT_INVALID                 (0xff)
@@ -1792,9 +2210,13 @@
 #define MPI3_DEVICE0_ASTATUS_DEVICE_BLOCKED                         (0x03)
 #define MPI3_DEVICE0_ASTATUS_UNAUTHORIZED                           (0x04)
 #define MPI3_DEVICE0_ASTATUS_DEVICE_MISSING_DELAY                   (0x05)
+#define MPI3_DEVICE0_ASTATUS_PREPARE                                (0x06)
+#define MPI3_DEVICE0_ASTATUS_SAFE_MODE                              (0x07)
+#define MPI3_DEVICE0_ASTATUS_GENERIC_MAX                            (0x0f)
 #define MPI3_DEVICE0_ASTATUS_SAS_UNKNOWN                            (0x10)
 #define MPI3_DEVICE0_ASTATUS_ROUTE_NOT_ADDRESSABLE                  (0x11)
 #define MPI3_DEVICE0_ASTATUS_SMP_ERROR_NOT_ADDRESSABLE              (0x12)
+#define MPI3_DEVICE0_ASTATUS_SAS_MAX                                (0x1f)
 #define MPI3_DEVICE0_ASTATUS_SIF_UNKNOWN                            (0x20)
 #define MPI3_DEVICE0_ASTATUS_SIF_AFFILIATION_CONFLICT               (0x21)
 #define MPI3_DEVICE0_ASTATUS_SIF_DIAG                               (0x22)
@@ -1810,6 +2232,8 @@
 #define MPI3_DEVICE0_ASTATUS_PCIE_MEM_SPACE_ACCESS                  (0x31)
 #define MPI3_DEVICE0_ASTATUS_PCIE_UNSUPPORTED                       (0x32)
 #define MPI3_DEVICE0_ASTATUS_PCIE_MSIX_REQUIRED                     (0x33)
+#define MPI3_DEVICE0_ASTATUS_PCIE_ECRC_REQUIRED                     (0x34)
+#define MPI3_DEVICE0_ASTATUS_PCIE_MAX                               (0x3f)
 #define MPI3_DEVICE0_ASTATUS_NVME_UNKNOWN                           (0x40)
 #define MPI3_DEVICE0_ASTATUS_NVME_READY_TIMEOUT                     (0x41)
 #define MPI3_DEVICE0_ASTATUS_NVME_DEVCFG_UNSUPPORTED                (0x42)
@@ -1820,19 +2244,28 @@
 #define MPI3_DEVICE0_ASTATUS_NVME_GET_FEATURE_STAT_FAILED           (0x47)
 #define MPI3_DEVICE0_ASTATUS_NVME_IDLE_TIMEOUT                      (0x48)
 #define MPI3_DEVICE0_ASTATUS_NVME_CTRL_FAILURE_STATUS               (0x49)
-#define MPI3_DEVICE0_ASTATUS_VD_UNKNOWN                             (0x50)
+#define MPI3_DEVICE0_ASTATUS_NVME_INSUFFICIENT_POWER                (0x4a)
+#define MPI3_DEVICE0_ASTATUS_NVME_DOORBELL_STRIDE                   (0x4b)
+#define MPI3_DEVICE0_ASTATUS_NVME_MEM_PAGE_MIN_SIZE                 (0x4c)
+#define MPI3_DEVICE0_ASTATUS_NVME_MEMORY_ALLOCATION                 (0x4d)
+#define MPI3_DEVICE0_ASTATUS_NVME_COMPLETION_TIME                   (0x4e)
+#define MPI3_DEVICE0_ASTATUS_NVME_BAR                               (0x4f)
+#define MPI3_DEVICE0_ASTATUS_NVME_NS_DESCRIPTOR                     (0x50)
+#define MPI3_DEVICE0_ASTATUS_NVME_INCOMPATIBLE_SETTINGS             (0x51)
+#define MPI3_DEVICE0_ASTATUS_NVME_TOO_MANY_ERRORS                   (0x52)
+#define MPI3_DEVICE0_ASTATUS_NVME_MAX                               (0x5f)
+#define MPI3_DEVICE0_ASTATUS_VD_UNKNOWN                             (0x80)
+#define MPI3_DEVICE0_ASTATUS_VD_MAX                                 (0x8f)
 #define MPI3_DEVICE0_FLAGS_CONTROLLER_DEV_HANDLE        (0x0080)
+#define MPI3_DEVICE0_FLAGS_IO_THROTTLING_REQUIRED       (0x0010)
 #define MPI3_DEVICE0_FLAGS_HIDDEN                       (0x0008)
-#define MPI3_DEVICE0_FLAGS_ATT_METHOD_MASK              (0x0006)
-#define MPI3_DEVICE0_FLAGS_ATT_METHOD_NOT_DIR_ATTACHED  (0x0000)
-#define MPI3_DEVICE0_FLAGS_ATT_METHOD_DIR_ATTACHED      (0x0002)
 #define MPI3_DEVICE0_FLAGS_ATT_METHOD_VIRTUAL           (0x0004)
+#define MPI3_DEVICE0_FLAGS_ATT_METHOD_DIR_ATTACHED      (0x0002)
 #define MPI3_DEVICE0_FLAGS_DEVICE_PRESENT               (0x0001)
 #define MPI3_DEVICE0_QUEUE_DEPTH_NOT_APPLICABLE         (0x0000)
 struct mpi3_device1_sas_sata_format {
 	__le32                             reserved00;
 };
-
 struct mpi3_device1_pcie_format {
 	__le16                             vendor_id;
 	__le16                             device_id;
@@ -1870,11 +2303,17 @@
 	struct mpi3_config_page_header         header;
 	__le16                             dev_handle;
 	__le16                             reserved0a;
-	__le32                             reserved0c[12];
+	__le16                             link_change_count;
+	__le16                             rate_change_count;
+	__le16                             tm_count;
+	__le16                             reserved12;
+	__le32                             reserved14[10];
 	u8                                 reserved3c[3];
 	u8                                 device_form;
 	union mpi3_device1_dev_spec_format    device_specific;
 };
 
 #define MPI3_DEVICE1_PAGEVERSION                            (0x00)
+#define MPI3_DEVICE1_COUNTER_MAX                            (0xfffe)
+#define MPI3_DEVICE1_COUNTER_INVALID                        (0xffff)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_image.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_image.h
@@ -61,6 +61,8 @@
 #define MPI3_IMAGE_HEADER_SIGNATURE1_SPD                      (0x20445053)
 #define MPI3_IMAGE_HEADER_SIGNATURE1_GAS_GAUGE                (0x20534147)
 #define MPI3_IMAGE_HEADER_SIGNATURE1_PBLP                     (0x504c4250)
+#define MPI3_IMAGE_HEADER_SIGNATURE1_MANIFEST                 (0x464e414d)
+#define MPI3_IMAGE_HEADER_SIGNATURE1_OEM                      (0x204d454f)
 #define MPI3_IMAGE_HEADER_SIGNATURE2_VALUE                    (0x50584546)
 #define MPI3_IMAGE_HEADER_FLAGS_DEVICE_KEY_BASIS_MASK         (0x00000030)
 #define MPI3_IMAGE_HEADER_FLAGS_DEVICE_KEY_BASIS_CDI          (0x00000000)
@@ -94,6 +96,61 @@
 #define MPI3_IMAGE_HEADER_HASH_EXCLUSION_OFFSET               (0x5c)
 #define MPI3_IMAGE_HEADER_NEXT_IMAGE_HEADER_OFFSET_OFFSET     (0x7c)
 #define MPI3_IMAGE_HEADER_SIZE                                (0x100)
+#ifndef MPI3_CI_MANIFEST_MPI_MAX
+#define MPI3_CI_MANIFEST_MPI_MAX                               (1)
+#endif
+struct mpi3_ci_manifest_mpi_comp_image_ref {
+	__le32                                signature1;
+	__le32                                reserved04[3];
+	struct mpi3_comp_image_version            component_image_version;
+	__le32                                component_image_version_string_offset;
+	__le32                                crc;
+};
+
+struct mpi3_ci_manifest_mpi {
+	u8                                       manifest_type;
+	u8                                       reserved01[3];
+	__le32                                   reserved04[3];
+	u8                                       num_image_references;
+	u8                                       release_level;
+	__le16                                   reserved12;
+	__le16                                   reserved14;
+	__le16                                   flags;
+	__le32                                   reserved18[2];
+	__le16                                   vendor_id;
+	__le16                                   device_id;
+	__le16                                   subsystem_vendor_id;
+	__le16                                   subsystem_id;
+	__le32                                   reserved28[2];
+	union mpi3_version_union                    package_security_version;
+	__le32                                   reserved34;
+	struct mpi3_comp_image_version               package_version;
+	__le32                                   package_version_string_offset;
+	__le32                                   package_build_date_string_offset;
+	__le32                                   package_build_time_string_offset;
+	__le32                                   reserved4c;
+	__le32                                   diag_authorization_identifier[16];
+	struct mpi3_ci_manifest_mpi_comp_image_ref   component_image_ref[MPI3_CI_MANIFEST_MPI_MAX];
+};
+
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_DEV                        (0x00)
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_PREALPHA                   (0x10)
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_ALPHA                      (0x20)
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_BETA                       (0x30)
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_RC                         (0x40)
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_GCA                        (0x50)
+#define MPI3_CI_MANIFEST_MPI_RELEASE_LEVEL_POINT                      (0x60)
+#define MPI3_CI_MANIFEST_MPI_FLAGS_DIAG_AUTHORIZATION                 (0x01)
+#define MPI3_CI_MANIFEST_MPI_SUBSYSTEMID_IGNORED                   (0xffff)
+#define MPI3_CI_MANIFEST_MPI_PKG_VER_STR_OFF_UNSPECIFIED           (0x00000000)
+#define MPI3_CI_MANIFEST_MPI_PKG_BUILD_DATE_STR_OFF_UNSPECIFIED    (0x00000000)
+#define MPI3_CI_MANIFEST_MPI_PKG_BUILD_TIME_STR_OFF_UNSPECIFIED    (0x00000000)
+union mpi3_ci_manifest {
+	struct mpi3_ci_manifest_mpi               mpi;
+	__le32                                dword[1];
+};
+
+#define MPI3_CI_MANIFEST_TYPE_MPI                                  (0x00)
 struct mpi3_extended_image_header {
 	u8                                image_type;
 	u8                                reserved01[3];
@@ -161,6 +218,7 @@
 #define MPI3_HASH_ALGORITHM_SIZE_UNUSED              (0x00)
 #define MPI3_HASH_ALGORITHM_SIZE_SHA256              (0x01)
 #define MPI3_HASH_ALGORITHM_SIZE_SHA512              (0x02)
+#define MPI3_HASH_ALGORITHM_SIZE_SHA384              (0x03)
 #define MPI3_ENCRYPTION_ALGORITHM_UNUSED             (0x00)
 #define MPI3_ENCRYPTION_ALGORITHM_RSA256             (0x01)
 #define MPI3_ENCRYPTION_ALGORITHM_RSA512             (0x02)
@@ -178,7 +236,6 @@
 	u8                         reserved03;
 	__le32                     reserved04;
 	__le32                     public_key[MPI3_PUBLIC_KEY_MAX];
-	__le32                     encrypted_hash[MPI3_ENCRYPTED_HASH_MAX];
 };
 
 #ifndef MPI3_ENCRYPTED_HASH_ENTRY_MAX
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_init.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_init.h
@@ -13,7 +13,7 @@
 	__le32             transfer_length;
 };
 
-union mpi3_scso_io_cdb_union {
+union mpi3_scsi_io_cdb_union {
 	u8                         cdb32[32];
 	struct mpi3_scsi_io_cdb_eedp32 eedp32;
 	struct mpi3_sge_common         sge;
@@ -32,11 +32,12 @@
 	__le32                     skip_count;
 	__le32                     data_length;
 	u8                         lun[8];
-	union mpi3_scso_io_cdb_union  cdb;
+	union mpi3_scsi_io_cdb_union  cdb;
 	union mpi3_sge_union          sgl[4];
 };
 
 #define MPI3_SCSIIO_MSGFLAGS_METASGL_VALID                  (0x80)
+#define MPI3_SCSIIO_MSGFLAGS_DIVERT_TO_FIRMWARE             (0x40)
 #define MPI3_SCSIIO_FLAGS_LARGE_CDB                         (0x60000000)
 #define MPI3_SCSIIO_FLAGS_CDB_16_OR_LESS                    (0x00000000)
 #define MPI3_SCSIIO_FLAGS_CDB_GREATER_THAN_16               (0x20000000)
@@ -54,6 +55,9 @@
 #define MPI3_SCSIIO_FLAGS_DATADIRECTION_READ                (0x00080000)
 #define MPI3_SCSIIO_FLAGS_DMAOPERATION_MASK                 (0x00030000)
 #define MPI3_SCSIIO_FLAGS_DMAOPERATION_HOST_PI              (0x00010000)
+#define MPI3_SCSIIO_FLAGS_DIVERT_REASON_MASK                (0x000000f0)
+#define MPI3_SCSIIO_FLAGS_DIVERT_REASON_IO_THROTTLING       (0x00000010)
+#define MPI3_SCSIIO_FLAGS_DIVERT_REASON_PROD_SPECIFIC       (0x00000080)
 #define MPI3_SCSIIO_METASGL_INDEX                           (3)
 struct mpi3_scsi_io_reply {
 	__le16                     host_tag;
@@ -111,49 +115,4 @@
 #define MPI3_SCSI_RSP_ARI0_MASK                 (0xff000000)
 #define MPI3_SCSI_RSP_ARI0_SHIFT                (24)
 #define MPI3_SCSI_TASKTAG_UNKNOWN               (0xffff)
-struct mpi3_scsi_task_mgmt_request {
-	__le16                     host_tag;
-	u8                         ioc_use_only02;
-	u8                         function;
-	__le16                     ioc_use_only04;
-	u8                         ioc_use_only06;
-	u8                         msg_flags;
-	__le16                     change_count;
-	__le16                     dev_handle;
-	__le16                     task_host_tag;
-	u8                         task_type;
-	u8                         reserved0f;
-	__le16                     task_request_queue_id;
-	__le16                     reserved12;
-	__le32                     reserved14;
-	u8                         lun[8];
-};
-
-#define MPI3_SCSITASKMGMT_MSGFLAGS_DO_NOT_SEND_TASK_IU      (0x08)
-#define MPI3_SCSITASKMGMT_TASKTYPE_ABORT_TASK               (0x01)
-#define MPI3_SCSITASKMGMT_TASKTYPE_ABORT_TASK_SET           (0x02)
-#define MPI3_SCSITASKMGMT_TASKTYPE_TARGET_RESET             (0x03)
-#define MPI3_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET       (0x05)
-#define MPI3_SCSITASKMGMT_TASKTYPE_CLEAR_TASK_SET           (0x06)
-#define MPI3_SCSITASKMGMT_TASKTYPE_QUERY_TASK               (0x07)
-#define MPI3_SCSITASKMGMT_TASKTYPE_CLEAR_ACA                (0x08)
-#define MPI3_SCSITASKMGMT_TASKTYPE_QUERY_TASK_SET           (0x09)
-#define MPI3_SCSITASKMGMT_TASKTYPE_QUERY_ASYNC_EVENT        (0x0a)
-#define MPI3_SCSITASKMGMT_TASKTYPE_I_T_NEXUS_RESET          (0x0b)
-struct mpi3_scsi_task_mgmt_reply {
-	__le16                     host_tag;
-	u8                         ioc_use_only02;
-	u8                         function;
-	__le16                     ioc_use_only04;
-	u8                         ioc_use_only06;
-	u8                         msg_flags;
-	__le16                     ioc_use_only08;
-	__le16                     ioc_status;
-	__le32                     ioc_log_info;
-	__le32                     termination_count;
-	__le32                     response_data;
-	__le32                     reserved18;
-};
-
-#define MPI3_SCSITASKMGMT_RSPCODE_IO_QUEUED_ON_IOC      (0x80)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_ioc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_ioc.h
@@ -29,20 +29,15 @@
 	__le64                   driver_information_address;
 };
 
-#define MPI3_WHOINIT_NOT_INITIALIZED            (0x00)
-#define MPI3_WHOINIT_ROM_BIOS                   (0x02)
-#define MPI3_WHOINIT_HOST_DRIVER                (0x03)
-#define MPI3_WHOINIT_MANUFACTURER               (0x04)
-struct mpi3_driver_info_layout {
-	__le32             information_length;
-	u8                 driver_signature[12];
-	u8                 os_name[16];
-	u8                 os_version[12];
-	u8                 driver_name[20];
-	u8                 driver_version[32];
-	u8                 driver_release_date[20];
-	__le32             driver_capabilities;
-};
+#define MPI3_IOCINIT_MSGFLAGS_HOSTMETADATA_MASK          (0x03)
+#define MPI3_IOCINIT_MSGFLAGS_HOSTMETADATA_NOT_USED      (0x00)
+#define MPI3_IOCINIT_MSGFLAGS_HOSTMETADATA_SEPARATED     (0x01)
+#define MPI3_IOCINIT_MSGFLAGS_HOSTMETADATA_INLINE        (0x02)
+#define MPI3_IOCINIT_MSGFLAGS_HOSTMETADATA_BOTH          (0x03)
+#define MPI3_WHOINIT_NOT_INITIALIZED                     (0x00)
+#define MPI3_WHOINIT_ROM_BIOS                            (0x02)
+#define MPI3_WHOINIT_HOST_DRIVER                         (0x03)
+#define MPI3_WHOINIT_MANUFACTURER                        (0x04)
 
 struct mpi3_ioc_facts_request {
 	__le16                 host_tag;
@@ -66,7 +61,7 @@
 	u8                         ioc_number;
 	u8                         who_init;
 	__le16                     max_msix_vectors;
-	__le16                     max_outstanding_request;
+	__le16                     max_outstanding_requests;
 	__le16                     product_id;
 	__le16                     ioc_request_frame_size;
 	__le16                     reply_frame_size;
@@ -77,17 +72,17 @@
 	u8                         sge_modifier_shift;
 	u8                         protocol_flags;
 	__le16                     max_sas_initiators;
-	__le16                     max_sas_targets;
+	__le16                     max_data_length;
 	__le16                     max_sas_expanders;
 	__le16                     max_enclosures;
 	__le16                     min_dev_handle;
 	__le16                     max_dev_handle;
-	__le16                     max_pc_ie_switches;
+	__le16                     max_pcie_switches;
 	__le16                     max_nvme;
-	__le16                     max_pds;
+	__le16                     reserved38;
 	__le16                     max_vds;
 	__le16                     max_host_pds;
-	__le16                     max_advanced_host_pds;
+	__le16                     max_adv_host_pds;
 	__le16                     max_raid_pds;
 	__le16                     max_posted_cmd_buffers;
 	__le32                     flags;
@@ -97,26 +92,47 @@
 	__le16                     reserved4e;
 	__le32                     diag_trace_size;
 	__le32                     diag_fw_size;
-};
-
-#define MPI3_IOCFACTS_CAPABILITY_ADVANCED_HOST_PD             (0x00000010)
+	__le32                     diag_driver_size;
+	u8                         max_host_pd_ns_count;
+	u8                         max_adv_host_pd_ns_count;
+	u8                         max_raidpd_ns_count;
+	u8                         max_devices_per_throttle_group;
+	__le16                     io_throttle_data_length;
+	__le16                     max_io_throttle_group;
+	__le16                     io_throttle_low;
+	__le16                     io_throttle_high;
+};
+#define MPI3_IOCFACTS_CAPABILITY_NON_SUPERVISOR_MASK          (0x80000000)
+#define MPI3_IOCFACTS_CAPABILITY_SUPERVISOR_IOC               (0x00000000)
+#define MPI3_IOCFACTS_CAPABILITY_NON_SUPERVISOR_IOC           (0x80000000)
+#define MPI3_IOCFACTS_CAPABILITY_INT_COALESCE_MASK            (0x00000600)
+#define MPI3_IOCFACTS_CAPABILITY_INT_COALESCE_FIXED_THRESHOLD (0x00000000)
+#define MPI3_IOCFACTS_CAPABILITY_INT_COALESCE_OUTSTANDING_IO  (0x00000200)
+#define MPI3_IOCFACTS_CAPABILITY_COMPLETE_RESET_CAPABLE       (0x00000100)
+#define MPI3_IOCFACTS_CAPABILITY_SEG_DIAG_TRACE_ENABLED       (0x00000080)
+#define MPI3_IOCFACTS_CAPABILITY_SEG_DIAG_FW_ENABLED          (0x00000040)
+#define MPI3_IOCFACTS_CAPABILITY_SEG_DIAG_DRIVER_ENABLED      (0x00000020)
+#define MPI3_IOCFACTS_CAPABILITY_ADVANCED_HOST_PD_ENABLED     (0x00000010)
 #define MPI3_IOCFACTS_CAPABILITY_RAID_CAPABLE                 (0x00000008)
-#define MPI3_IOCFACTS_CAPABILITY_COALESCE_CTRL_GRAN_MASK      (0x00000001)
-#define MPI3_IOCFACTS_CAPABILITY_COALESCE_CTRL_IOC_GRAN       (0x00000000)
-#define MPI3_IOCFACTS_CAPABILITY_COALESCE_CTRL_REPLY_Q_GRAN   (0x00000001)
+#define MPI3_IOCFACTS_CAPABILITY_MULTIPATH_ENABLED            (0x00000002)
+#define MPI3_IOCFACTS_CAPABILITY_COALESCE_CTRL_SUPPORTED      (0x00000001)
 #define MPI3_IOCFACTS_PID_TYPE_MASK                           (0xf000)
 #define MPI3_IOCFACTS_PID_TYPE_SHIFT                          (12)
 #define MPI3_IOCFACTS_PID_PRODUCT_MASK                        (0x0f00)
 #define MPI3_IOCFACTS_PID_PRODUCT_SHIFT                       (8)
 #define MPI3_IOCFACTS_PID_FAMILY_MASK                         (0x00ff)
 #define MPI3_IOCFACTS_PID_FAMILY_SHIFT                        (0)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_REKEY                   (0x2000)
+#define MPI3_IOCFACTS_EXCEPT_SAS_DISABLED                     (0x1000)
 #define MPI3_IOCFACTS_EXCEPT_SAFE_MODE                        (0x0800)
 #define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_MASK                (0x0700)
 #define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_NONE                (0x0000)
-#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_LOCAL_VIA_RAID      (0x0100)
-#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_LOCAL_VIA_OOB       (0x0200)
-#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_EXT_VIA_RAID        (0x0300)
-#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_EXT_VIA_OOB         (0x0400)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_LOCAL_VIA_MGMT      (0x0100)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_EXT_VIA_MGMT        (0x0200)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_DRIVE_EXT_VIA_MGMT  (0x0300)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_LOCAL_VIA_OOB       (0x0400)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_EXT_VIA_OOB         (0x0500)
+#define MPI3_IOCFACTS_EXCEPT_SECURITY_KEY_DRIVE_EXT_VIA_OOB   (0x0600)
 #define MPI3_IOCFACTS_EXCEPT_PCIE_DISABLED                    (0x0080)
 #define MPI3_IOCFACTS_EXCEPT_PARTIAL_MEMORY_FAILURE           (0x0040)
 #define MPI3_IOCFACTS_EXCEPT_MANUFACT_CHECKSUM_FAIL           (0x0020)
@@ -130,6 +146,7 @@
 #define MPI3_IOCFACTS_PROTOCOL_NVME                           (0x0004)
 #define MPI3_IOCFACTS_PROTOCOL_SCSI_INITIATOR                 (0x0002)
 #define MPI3_IOCFACTS_PROTOCOL_SCSI_TARGET                    (0x0001)
+#define MPI3_IOCFACTS_MAX_DATA_LENGTH_NOT_REPORTED            (0x0000)
 #define MPI3_IOCFACTS_FLAGS_SIGNED_NVDATA_REQUIRED            (0x00010000)
 #define MPI3_IOCFACTS_FLAGS_DMA_ADDRESS_WIDTH_MASK            (0x0000ff00)
 #define MPI3_IOCFACTS_FLAGS_DMA_ADDRESS_WIDTH_SHIFT           (8)
@@ -140,6 +157,7 @@
 #define MPI3_IOCFACTS_FLAGS_PERSONALITY_MASK                  (0x0000000f)
 #define MPI3_IOCFACTS_FLAGS_PERSONALITY_EHBA                  (0x00000000)
 #define MPI3_IOCFACTS_FLAGS_PERSONALITY_RAID_DDR              (0x00000002)
+#define MPI3_IOCFACTS_IO_THROTTLE_DATA_LENGTH_NOT_REQUIRED    (0x0000)
 struct mpi3_mgmt_passthrough_request {
 	__le16                 host_tag;
 	u8                     ioc_use_only02;
@@ -175,6 +193,7 @@
 #define MPI3_CREATE_REQUEST_QUEUE_FLAGS_SEGMENTED_MASK          (0x80)
 #define MPI3_CREATE_REQUEST_QUEUE_FLAGS_SEGMENTED_SEGMENTED     (0x80)
 #define MPI3_CREATE_REQUEST_QUEUE_FLAGS_SEGMENTED_CONTIGUOUS    (0x00)
+#define MPI3_CREATE_REQUEST_QUEUE_SIZE_MINIMUM                  (2)
 struct mpi3_delete_request_queue_request {
 	__le16             host_tag;
 	u8                 ioc_use_only02;
@@ -207,9 +226,11 @@
 #define MPI3_CREATE_REPLY_QUEUE_FLAGS_SEGMENTED_MASK            (0x80)
 #define MPI3_CREATE_REPLY_QUEUE_FLAGS_SEGMENTED_SEGMENTED       (0x80)
 #define MPI3_CREATE_REPLY_QUEUE_FLAGS_SEGMENTED_CONTIGUOUS      (0x00)
+#define MPI3_CREATE_REPLY_QUEUE_FLAGS_COALESCE_DISABLE          (0x02)
 #define MPI3_CREATE_REPLY_QUEUE_FLAGS_INT_ENABLE_MASK           (0x01)
 #define MPI3_CREATE_REPLY_QUEUE_FLAGS_INT_ENABLE_DISABLE        (0x00)
 #define MPI3_CREATE_REPLY_QUEUE_FLAGS_INT_ENABLE_ENABLE         (0x01)
+#define MPI3_CREATE_REPLY_QUEUE_SIZE_MINIMUM                    (2)
 struct mpi3_delete_reply_queue_request {
 	__le16             host_tag;
 	u8                 ioc_use_only02;
@@ -235,7 +256,6 @@
 #define MPI3_EVENT_LOG_DATA                         (0x01)
 #define MPI3_EVENT_CHANGE                           (0x02)
 #define MPI3_EVENT_GPIO_INTERRUPT                   (0x04)
-#define MPI3_EVENT_TEMP_THRESHOLD                   (0x05)
 #define MPI3_EVENT_CABLE_MGMT                       (0x06)
 #define MPI3_EVENT_DEVICE_ADDED                     (0x07)
 #define MPI3_EVENT_DEVICE_INFO_CHANGED              (0x08)
@@ -255,7 +275,9 @@
 #define MPI3_EVENT_SAS_DEVICE_DISCOVERY_ERROR       (0x19)
 #define MPI3_EVENT_PCIE_TOPOLOGY_CHANGE_LIST        (0x20)
 #define MPI3_EVENT_PCIE_ENUMERATION                 (0x22)
+#define MPI3_EVENT_PCIE_ERROR_THRESHOLD             (0x23)
 #define MPI3_EVENT_HARD_RESET_RECEIVED              (0x40)
+#define MPI3_EVENT_DIAGNOSTIC_BUFFER_STATUS_CHANGE  (0x50)
 #define MPI3_EVENT_MIN_PRODUCT_SPECIFIC             (0x60)
 #define MPI3_EVENT_MAX_PRODUCT_SPECIFIC             (0x7f)
 #define MPI3_EVENT_NOTIFY_EVENTMASK_WORDS           (4)
@@ -300,21 +322,6 @@
 	u8                 gpio_num;
 	u8                 reserved01[3];
 };
-
-struct mpi3_event_data_temp_threshold {
-	__le16             status;
-	u8                 sensor_num;
-	u8                 reserved03;
-	__le16             current_temperature;
-	__le16             reserved06;
-	__le32             reserved08;
-	__le32             reserved0c;
-};
-
-#define MPI3_EVENT_TEMP_THRESHOLD_STATUS_THRESHOLD3_EXCEEDED         (0x0008)
-#define MPI3_EVENT_TEMP_THRESHOLD_STATUS_THRESHOLD2_EXCEEDED         (0x0004)
-#define MPI3_EVENT_TEMP_THRESHOLD_STATUS_THRESHOLD1_EXCEEDED         (0x0002)
-#define MPI3_EVENT_TEMP_THRESHOLD_STATUS_THRESHOLD0_EXCEEDED         (0x0001)
 struct mpi3_event_data_cable_management {
 	__le32             active_cable_power_requirement;
 	u8                 status;
@@ -398,8 +405,10 @@
 #define MPI3_SAS_DISC_STATUS_MAX_EXPANDERS_EXCEED             (0x40000000)
 #define MPI3_SAS_DISC_STATUS_MAX_DEVICES_EXCEED               (0x20000000)
 #define MPI3_SAS_DISC_STATUS_MAX_TOPO_PHYS_EXCEED             (0x10000000)
+#define MPI3_SAS_DISC_STATUS_INVALID_CEI                      (0x00010000)
+#define MPI3_SAS_DISC_STATUS_FECEI_MISMATCH                   (0x00008000)
 #define MPI3_SAS_DISC_STATUS_MULTIPLE_DEVICES_IN_SLOT         (0x00004000)
-#define MPI3_SAS_DISC_STATUS_SLOT_COUNT_MISMATCH              (0x00002000)
+#define MPI3_SAS_DISC_STATUS_NECEI_MISMATCH                   (0x00002000)
 #define MPI3_SAS_DISC_STATUS_TOO_MANY_SLOTS                   (0x00001000)
 #define MPI3_SAS_DISC_STATUS_EXP_MULTI_SUBTRACTIVE            (0x00000800)
 #define MPI3_SAS_DISC_STATUS_MULTI_PORT_DOMAIN                (0x00000400)
@@ -581,6 +590,20 @@
 #define MPI3_EVENT_PCIE_TOPO_SS_NOT_RESPONDING          (0x02)
 #define MPI3_EVENT_PCIE_TOPO_SS_RESPONDING              (0x03)
 #define MPI3_EVENT_PCIE_TOPO_SS_DELAY_NOT_RESPONDING    (0x04)
+struct mpi3_event_data_pcie_error_threshold {
+	__le64                                 timestamp;
+	u8                                     reason_code;
+	u8                                     port;
+	__le16                                 switch_dev_handle;
+	u8                                     error;
+	u8                                     action;
+	__le16                                 threshold_count;
+	__le16                                 attached_dev_handle;
+	__le16                                 reserved12;
+};
+
+#define MPI3_EVENT_PCI_ERROR_RC_THRESHOLD_EXCEEDED          (0x00)
+#define MPI3_EVENT_PCI_ERROR_RC_ESCALATION                  (0x01)
 struct mpi3_event_data_sas_init_dev_status_change {
 	u8                 reason_code;
 	u8                 io_unit_port;
@@ -604,23 +627,16 @@
 	__le16             reserved02;
 };
 
-#define MPI3_PEL_LOCALE_FLAGS_NON_BLOCKING_BOOT_EVENT   (0x0200)
-#define MPI3_PEL_LOCALE_FLAGS_BLOCKING_BOOT_EVENT       (0x0100)
-#define MPI3_PEL_LOCALE_FLAGS_PCIE                      (0x0080)
-#define MPI3_PEL_LOCALE_FLAGS_CONFIGURATION             (0x0040)
-#define MPI3_PEL_LOCALE_FLAGS_CONTROLER                 (0x0020)
-#define MPI3_PEL_LOCALE_FLAGS_SAS                       (0x0010)
-#define MPI3_PEL_LOCALE_FLAGS_EPACK                     (0x0008)
-#define MPI3_PEL_LOCALE_FLAGS_ENCLOSURE                 (0x0004)
-#define MPI3_PEL_LOCALE_FLAGS_PD                        (0x0002)
-#define MPI3_PEL_LOCALE_FLAGS_VD                        (0x0001)
-#define MPI3_PEL_CLASS_DEBUG                            (0x00)
-#define MPI3_PEL_CLASS_PROGRESS                         (0x01)
-#define MPI3_PEL_CLASS_INFORMATIONAL                    (0x02)
-#define MPI3_PEL_CLASS_WARNING                          (0x03)
-#define MPI3_PEL_CLASS_CRITICAL                         (0x04)
-#define MPI3_PEL_CLASS_FATAL                            (0x05)
-#define MPI3_PEL_CLASS_FAULT                            (0x06)
+struct mpi3_event_data_diag_buffer_status_change {
+	u8                 type;
+	u8                 reason_code;
+	__le16             reserved02;
+	__le32             reserved04;
+};
+
+#define MPI3_EVENT_DIAG_BUFFER_STATUS_CHANGE_RC_RELEASED             (0x01)
+#define MPI3_EVENT_DIAG_BUFFER_STATUS_CHANGE_RC_PAUSED               (0x02)
+#define MPI3_EVENT_DIAG_BUFFER_STATUS_CHANGE_RC_RESUMED              (0x03)
 #define MPI3_PEL_CLEARTYPE_CLEAR                        (0x00)
 #define MPI3_PEL_WAITTIME_INFINITE_WAIT                 (0x00)
 #define MPI3_PEL_ACTION_GET_SEQNUM                      (0x01)
@@ -645,21 +661,23 @@
 };
 
 struct mpi3_pel_entry {
+	__le64                             time_stamp;
 	__le32                             sequence_number;
-	__le32                             time_stamp[2];
 	__le16                             log_code;
 	__le16                             arg_type;
 	__le16                             locale;
 	u8                                 class;
-	u8                                 reserved13;
+	u8                                 flags;
 	u8                                 ext_num;
 	u8                                 num_exts;
 	u8                                 arg_data_size;
-	u8                                 fixed_format_size;
+	u8                                 fixed_format_strings_size;
 	__le32                             reserved18[2];
 	__le32                             pel_info[24];
 };
 
+#define MPI3_PEL_FLAGS_COMPLETE_RESET_NEEDED                  (0x02)
+#define MPI3_PEL_FLAGS_ACK_NEEDED                             (0x01)
 struct mpi3_pel_list {
 	__le32                             log_count;
 	__le32                             reserved04;
@@ -837,7 +855,10 @@
 	__le32                             reserved10;
 };
 
-#define MPI3_PELACKNOWLEDGE_MSGFLAGS_SAFE_MODE_EXIT            (0x01)
+#define MPI3_PELACKNOWLEDGE_MSGFLAGS_SAFE_MODE_EXIT_MASK                     (0x03)
+#define MPI3_PELACKNOWLEDGE_MSGFLAGS_SAFE_MODE_EXIT_NO_GUIDANCE              (0x00)
+#define MPI3_PELACKNOWLEDGE_MSGFLAGS_SAFE_MODE_EXIT_CONTINUE_OP              (0x01)
+#define MPI3_PELACKNOWLEDGE_MSGFLAGS_SAFE_MODE_EXIT_TRANSITION_TO_FAULT      (0x02)
 struct mpi3_pel_reply {
 	__le16                             host_tag;
 	u8                                 ioc_use_only02;
@@ -885,6 +906,7 @@
 #define MPI3_CI_DOWNLOAD_ACTION_ONLINE_ACTIVATION              (0x02)
 #define MPI3_CI_DOWNLOAD_ACTION_OFFLINE_ACTIVATION             (0x03)
 #define MPI3_CI_DOWNLOAD_ACTION_GET_STATUS                     (0x04)
+#define MPI3_CI_DOWNLOAD_ACTION_CANCEL_OFFLINE_ACTIVATION      (0x05)
 struct mpi3_ci_download_reply {
 	__le16                             host_tag;
 	u8                                 ioc_use_only02;
@@ -902,6 +924,7 @@
 };
 
 #define MPI3_CI_DOWNLOAD_FLAGS_DOWNLOAD_IN_PROGRESS                  (0x80)
+#define MPI3_CI_DOWNLOAD_FLAGS_OFFLINE_ACTIVATION_REQUIRED           (0x20)
 #define MPI3_CI_DOWNLOAD_FLAGS_KEY_UPDATE_PENDING                    (0x10)
 #define MPI3_CI_DOWNLOAD_FLAGS_ACTIVATION_STATUS_MASK                (0x0e)
 #define MPI3_CI_DOWNLOAD_FLAGS_ACTIVATION_STATUS_NOT_NEEDED          (0x00)
@@ -936,22 +959,34 @@
 #define MPI3_CTRL_OP_LOOKUP_MAPPING                                  (0x02)
 #define MPI3_CTRL_OP_UPDATE_TIMESTAMP                                (0x04)
 #define MPI3_CTRL_OP_GET_TIMESTAMP                                   (0x05)
+#define MPI3_CTRL_OP_GET_IOC_CHANGE_COUNT                            (0x06)
+#define MPI3_CTRL_OP_CHANGE_PROFILE                                  (0x07)
 #define MPI3_CTRL_OP_REMOVE_DEVICE                                   (0x10)
 #define MPI3_CTRL_OP_CLOSE_PERSISTENT_CONNECTION                     (0x11)
 #define MPI3_CTRL_OP_HIDDEN_ACK                                      (0x12)
-#define MPI3_CTRL_OP_SAS_SEND_PRIMITIVE                              (0x20)
-#define MPI3_CTRL_OP_SAS_CLEAR_ERROR_LOG                             (0x21)
-#define MPI3_CTRL_OP_PCIE_CLEAR_ERROR_LOG                            (0x22)
+#define MPI3_CTRL_OP_CLEAR_DEVICE_COUNTERS                           (0x13)
+#define MPI3_CTRL_OP_SEND_SAS_PRIMITIVE                              (0x20)
+#define MPI3_CTRL_OP_SAS_PHY_CONTROL                                 (0x21)
+#define MPI3_CTRL_OP_READ_INTERNAL_BUS                               (0x23)
+#define MPI3_CTRL_OP_WRITE_INTERNAL_BUS                              (0x24)
+#define MPI3_CTRL_OP_PCIE_LINK_CONTROL                               (0x30)
 #define MPI3_CTRL_OP_LOOKUP_MAPPING_PARAM8_LOOKUP_METHOD_INDEX       (0x00)
 #define MPI3_CTRL_OP_UPDATE_TIMESTAMP_PARAM64_TIMESTAMP_INDEX        (0x00)
+#define MPI3_CTRL_OP_CHANGE_PROFILE_PARAM8_PROFILE_ID_INDEX          (0x00)
 #define MPI3_CTRL_OP_REMOVE_DEVICE_PARAM16_DEVHANDLE_INDEX           (0x00)
 #define MPI3_CTRL_OP_CLOSE_PERSIST_CONN_PARAM16_DEVHANDLE_INDEX      (0x00)
 #define MPI3_CTRL_OP_HIDDEN_ACK_PARAM16_DEVHANDLE_INDEX              (0x00)
-#define MPI3_CTRL_OP_SAS_SEND_PRIM_PARAM8_PHY_INDEX                  (0x00)
-#define MPI3_CTRL_OP_SAS_SEND_PRIM_PARAM8_PRIMSEQ_INDEX              (0x01)
-#define MPI3_CTRL_OP_SAS_SEND_PRIM_PARAM32_PRIMITIVE_INDEX           (0x00)
-#define MPI3_CTRL_OP_SAS_CLEAR_ERR_LOG_PARAM8_PHY_INDEX              (0x00)
-#define MPI3_CTRL_OP_PCIE_CLEAR_ERR_LOG_PARAM8_PHY_INDEX             (0x00)
+#define MPI3_CTRL_OP_CLEAR_DEVICE_COUNTERS_PARAM16_DEVHANDLE_INDEX   (0x00)
+#define MPI3_CTRL_OP_SEND_SAS_PRIM_PARAM8_PHY_INDEX                  (0x00)
+#define MPI3_CTRL_OP_SEND_SAS_PRIM_PARAM8_PRIMSEQ_INDEX              (0x01)
+#define MPI3_CTRL_OP_SEND_SAS_PRIM_PARAM32_PRIMITIVE_INDEX           (0x00)
+#define MPI3_CTRL_OP_SAS_PHY_CONTROL_PARAM8_ACTION_INDEX             (0x00)
+#define MPI3_CTRL_OP_SAS_PHY_CONTROL_PARAM8_PHY_INDEX                (0x01)
+#define MPI3_CTRL_OP_READ_INTERNAL_BUS_PARAM64_ADDRESS_INDEX         (0x00)
+#define MPI3_CTRL_OP_WRITE_INTERNAL_BUS_PARAM64_ADDRESS_INDEX        (0x00)
+#define MPI3_CTRL_OP_WRITE_INTERNAL_BUS_PARAM32_VALUE_INDEX          (0x00)
+#define MPI3_CTRL_OP_PCIE_LINK_CONTROL_PARAM8_ACTION_INDEX           (0x00)
+#define MPI3_CTRL_OP_PCIE_LINK_CONTROL_PARAM8_LINK_INDEX             (0x01)
 #define MPI3_CTRL_LOOKUP_METHOD_WWID_ADDRESS                         (0x01)
 #define MPI3_CTRL_LOOKUP_METHOD_ENCLOSURE_SLOT                       (0x02)
 #define MPI3_CTRL_LOOKUP_METHOD_SAS_DEVICE_NAME                      (0x03)
@@ -966,9 +1001,15 @@
 #define MPI3_CTRL_LOOKUP_METHOD_PERSISTID_PARAM16_PERSISTENT_ID_INDEX   (1)
 #define MPI3_CTRL_LOOKUP_METHOD_VALUE16_DEVH_INDEX                      (0)
 #define MPI3_CTRL_GET_TIMESTAMP_VALUE64_TIMESTAMP_INDEX                 (0)
+#define MPI3_CTRL_GET_IOC_CHANGE_COUNT_VALUE16_CHANGECOUNT_INDEX        (0)
+#define MPI3_CTRL_READ_INTERNAL_BUS_VALUE32_VALUE_INDEX                 (0)
 #define MPI3_CTRL_PRIMFLAGS_SINGLE                                   (0x01)
 #define MPI3_CTRL_PRIMFLAGS_TRIPLE                                   (0x03)
 #define MPI3_CTRL_PRIMFLAGS_REDUNDANT                                (0x06)
+#define MPI3_CTRL_ACTION_NOP                                         (0x00)
+#define MPI3_CTRL_ACTION_LINK_RESET                                  (0x01)
+#define MPI3_CTRL_ACTION_HARD_RESET                                  (0x02)
+#define MPI3_CTRL_ACTION_CLEAR_ERROR_LOG                             (0x05)
 struct mpi3_iounit_control_request {
 	__le16                             host_tag;
 	u8                                 ioc_use_only02;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_pci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_pci.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  Copyright 2016-2021 Broadcom Inc. All rights reserved.
+ *
+ */
+#ifndef MPI30_PCI_H
+#define MPI30_PCI_H     1
+
+#define MPI3_NVME_FLAGS_FORCE_ADMIN_ERR_REPLY_MASK      (0x0002)
+#define MPI3_NVME_FLAGS_FORCE_ADMIN_ERR_REPLY_FAIL_ONLY (0x0000)
+#define MPI3_NVME_FLAGS_FORCE_ADMIN_ERR_REPLY_ALL       (0x0002)
+#define MPI3_NVME_FLAGS_SUBMISSIONQ_MASK                (0x0001)
+#define MPI3_NVME_FLAGS_SUBMISSIONQ_IO                  (0x0000)
+#define MPI3_NVME_FLAGS_SUBMISSIONQ_ADMIN               (0x0001)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_sas.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_sas.h
@@ -30,4 +30,18 @@
 	struct mpi3_sge_common         request_sge;
 	struct mpi3_sge_common         response_sge;
 };
+
+struct mpi3_smp_passthrough_reply {
+	__le16                     host_tag;
+	u8                         ioc_use_only02;
+	u8                         function;
+	__le16                     ioc_use_only04;
+	u8                         ioc_use_only06;
+	u8                         msg_flags;
+	__le16                     ioc_use_only08;
+	__le16                     ioc_status;
+	__le32                     ioc_log_info;
+	__le16                     response_data_length;
+	__le16                     reserved12;
+};
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi/mpi30_transport.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi/mpi30_transport.h
@@ -19,8 +19,9 @@
 
 #define MPI3_VERSION_MAJOR                                              (3)
 #define MPI3_VERSION_MINOR                                              (0)
-#define MPI3_VERSION_UNIT                                               (0)
-#define MPI3_VERSION_DEV                                                (18)
+#define MPI3_VERSION_UNIT                                               (23)
+#define MPI3_VERSION_DEV                                                (1)
+#define MPI3_DEVHANDLE_INVALID                                          (0xffff)
 struct mpi3_sysif_oper_queue_indexes {
 	__le16         producer_index;
 	__le16         reserved02;
@@ -74,6 +75,7 @@
 #define MPI3_SYSIF_IOC_INFO_HIGH_OFFSET                                 (0x00000004)
 #define MPI3_SYSIF_IOC_INFO_LOW_TIMEOUT_MASK                            (0xff000000)
 #define MPI3_SYSIF_IOC_INFO_LOW_TIMEOUT_SHIFT                           (24)
+#define MPI3_SYSIF_IOC_INFO_LOW_HCB_DISABLED                            (0x00000001)
 #define MPI3_SYSIF_IOC_CONFIG_OFFSET                                    (0x00000014)
 #define MPI3_SYSIF_IOC_CONFIG_OPER_RPY_ENT_SZ                           (0x00f00000)
 #define MPI3_SYSIF_IOC_CONFIG_OPER_RPY_ENT_SZ_SHIFT                     (20)
@@ -82,12 +84,13 @@
 #define MPI3_SYSIF_IOC_CONFIG_SHUTDOWN_MASK                             (0x0000c000)
 #define MPI3_SYSIF_IOC_CONFIG_SHUTDOWN_NO                               (0x00000000)
 #define MPI3_SYSIF_IOC_CONFIG_SHUTDOWN_NORMAL                           (0x00004000)
-#define MPI3_SYSIF_IOC_CONFIG_DEVICE_SHUTDOWN                           (0x00002000)
+#define MPI3_SYSIF_IOC_CONFIG_DEVICE_SHUTDOWN_SEND_REQ                  (0x00002000)
 #define MPI3_SYSIF_IOC_CONFIG_DIAG_SAVE                                 (0x00000010)
 #define MPI3_SYSIF_IOC_CONFIG_ENABLE_IOC                                (0x00000001)
 #define MPI3_SYSIF_IOC_STATUS_OFFSET                                    (0x0000001c)
 #define MPI3_SYSIF_IOC_STATUS_RESET_HISTORY                             (0x00000010)
 #define MPI3_SYSIF_IOC_STATUS_SHUTDOWN_MASK                             (0x0000000c)
+#define MPI3_SYSIF_IOC_STATUS_SHUTDOWN_SHIFT                            (0x00000002)
 #define MPI3_SYSIF_IOC_STATUS_SHUTDOWN_NONE                             (0x00000000)
 #define MPI3_SYSIF_IOC_STATUS_SHUTDOWN_IN_PROGRESS                      (0x00000004)
 #define MPI3_SYSIF_IOC_STATUS_SHUTDOWN_COMPLETE                         (0x00000008)
@@ -107,9 +110,9 @@
 #define MPI3_SYSIF_COALESCE_CONTROL_ENABLE_NO_CHANGE                    (0x00000000)
 #define MPI3_SYSIF_COALESCE_CONTROL_ENABLE_DISABLE                      (0x40000000)
 #define MPI3_SYSIF_COALESCE_CONTROL_ENABLE_ENABLE                       (0xc0000000)
-#define MPI3_SYSIF_COALESCE_CONTROL_VALID                               (0x30000000)
-#define MPI3_SYSIF_COALESCE_CONTROL_QUEUE_ID_MASK                       (0x00ff0000)
-#define MPI3_SYSIF_COALESCE_CONTROL_QUEUE_ID_SHIFT                      (16)
+#define MPI3_SYSIF_COALESCE_CONTROL_VALID                               (0x20000000)
+#define MPI3_SYSIF_COALESCE_CONTROL_MSIX_IDX_MASK                       (0x01ff0000)
+#define MPI3_SYSIF_COALESCE_CONTROL_MSIX_IDX_SHIFT                      (16)
 #define MPI3_SYSIF_COALESCE_CONTROL_TIMEOUT_MASK                        (0x0000ff00)
 #define MPI3_SYSIF_COALESCE_CONTROL_TIMEOUT_SHIFT                       (8)
 #define MPI3_SYSIF_COALESCE_CONTROL_DEPTH_MASK                          (0x000000ff)
@@ -117,9 +120,9 @@
 #define MPI3_SYSIF_ADMIN_REQ_Q_PI_OFFSET                                (0x00001000)
 #define MPI3_SYSIF_ADMIN_REPLY_Q_CI_OFFSET                              (0x00001004)
 #define MPI3_SYSIF_OPER_REQ_Q_PI_OFFSET                                 (0x00001008)
-#define MPI3_SYSIF_OPER_REQ_Q_N_PI_OFFSET(n)                            (MPI3_SYSIF_OPER_REQ_Q_PI_OFFSET + (((n) - 1) * 8))
+#define MPI3_SYSIF_OPER_REQ_Q_N_PI_OFFSET(N)                            (MPI3_SYSIF_OPER_REQ_Q_PI_OFFSET + (((N) - 1) * 8))
 #define MPI3_SYSIF_OPER_REPLY_Q_CI_OFFSET                               (0x0000100c)
-#define MPI3_SYSIF_OPER_REPLY_Q_N_CI_OFFSET(n)                          (MPI3_SYSIF_OPER_REPLY_Q_CI_OFFSET + (((n) - 1) * 8))
+#define MPI3_SYSIF_OPER_REPLY_Q_N_CI_OFFSET(N)                          (MPI3_SYSIF_OPER_REPLY_Q_CI_OFFSET + (((N) - 1) * 8))
 #define MPI3_SYSIF_WRITE_SEQUENCE_OFFSET                                (0x00001c04)
 #define MPI3_SYSIF_WRITE_SEQUENCE_KEY_VALUE_MASK                        (0x0000000f)
 #define MPI3_SYSIF_WRITE_SEQUENCE_KEY_VALUE_FLUSH                       (0x0)
@@ -133,7 +136,7 @@
 #define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_MASK                          (0x00000700)
 #define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_NO_RESET                      (0x00000000)
 #define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET                    (0x00000100)
-#define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_FLASH_RCVRY_RESET             (0x00000200)
+#define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_HOST_CONTROL_BOOT_RESET       (0x00000200)
 #define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_COMPLETE_RESET                (0x00000300)
 #define MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT                    (0x00000700)
 #define MPI3_SYSIF_HOST_DIAG_SAVE_IN_PROGRESS                           (0x00000080)
@@ -153,8 +156,9 @@
 #define MPI3_SYSIF_FAULT_CODE_CI_ACTIVATION_RESET                       (0x0000f001)
 #define MPI3_SYSIF_FAULT_CODE_SOFT_RESET_IN_PROGRESS                    (0x0000f002)
 #define MPI3_SYSIF_FAULT_CODE_COMPLETE_RESET_NEEDED                     (0x0000f003)
-#define MPI3_SYSIF_FAULT_CODE_SAFE_MODE_EXIT                            (0x0000f004)
-#define MPI3_SYSIF_FAULT_CODE_FACTORY_RESET                             (0x0000f005)
+#define MPI3_SYSIF_FAULT_CODE_SOFT_RESET_NEEDED                         (0x0000f004)
+#define MPI3_SYSIF_FAULT_CODE_POWER_CYCLE_REQUIRED                      (0x0000f005)
+#define MPI3_SYSIF_FAULT_CODE_TEMP_THRESHOLD_EXCEEDED                   (0x0000f006)
 #define MPI3_SYSIF_FAULT_INFO0_OFFSET                                   (0x00001c14)
 #define MPI3_SYSIF_FAULT_INFO1_OFFSET                                   (0x00001c18)
 #define MPI3_SYSIF_FAULT_INFO2_OFFSET                                   (0x00001c1c)
@@ -305,7 +309,7 @@
 #define MPI3_SGE_FLAGS_END_OF_BUFFER            (0x04)
 #define MPI3_SGE_FLAGS_DLAS_MASK                (0x03)
 #define MPI3_SGE_FLAGS_DLAS_SYSTEM              (0x00)
-#define MPI3_SGE_FLAGS_DLAS_IOC_DDR             (0x01)
+#define MPI3_SGE_FLAGS_DLAS_IOC_UDP             (0x01)
 #define MPI3_SGE_FLAGS_DLAS_IOC_CTL             (0x02)
 #define MPI3_SGE_EXT_OPER_EEDP                  (0x00)
 #define MPI3_EEDPFLAGS_INCR_PRI_REF_TAG             (0x8000)
@@ -326,7 +330,6 @@
 #define MPI3_EEDPFLAGS_HOST_GUARD_OEM_SPECIFIC      (0x0020)
 #define MPI3_EEDPFLAGS_PT_REF_TAG                   (0x0008)
 #define MPI3_EEDPFLAGS_EEDP_OP_MASK                 (0x0007)
-#define MPI3_EEDPFLAGS_EEDP_OP_NOOP                 (0x0000)
 #define MPI3_EEDPFLAGS_EEDP_OP_CHECK                (0x0001)
 #define MPI3_EEDPFLAGS_EEDP_OP_STRIP                (0x0002)
 #define MPI3_EEDPFLAGS_EEDP_OP_CHECK_REMOVE         (0x0003)
@@ -409,6 +412,8 @@
 #define MPI3_IOCSTATUS_INVALID_STATE                (0x0008)
 #define MPI3_IOCSTATUS_INSUFFICIENT_POWER           (0x000a)
 #define MPI3_IOCSTATUS_INVALID_CHANGE_COUNT         (0x000b)
+#define MPI3_IOCSTATUS_ALLOWED_CMD_BLOCK            (0x000c)
+#define MPI3_IOCSTATUS_SUPERVISOR_ONLY              (0x000d)
 #define MPI3_IOCSTATUS_FAILURE                      (0x001f)
 #define MPI3_IOCSTATUS_CONFIG_INVALID_ACTION        (0x0020)
 #define MPI3_IOCSTATUS_CONFIG_INVALID_TYPE          (0x0021)
@@ -448,8 +453,10 @@
 #define MPI3_IOCSTATUS_CI_UNSUPPORTED               (0x00b0)
 #define MPI3_IOCSTATUS_CI_UPDATE_SEQUENCE           (0x00b1)
 #define MPI3_IOCSTATUS_CI_VALIDATION_FAILED         (0x00b2)
-#define MPI3_IOCSTATUS_CI_UPDATE_PENDING            (0x00b3)
+#define MPI3_IOCSTATUS_CI_KEY_UPDATE_PENDING        (0x00b3)
+#define MPI3_IOCSTATUS_CI_KEY_UPDATE_NOT_POSSIBLE   (0x00b4)
 #define MPI3_IOCSTATUS_SECURITY_KEY_REQUIRED        (0x00c0)
+#define MPI3_IOCSTATUS_SECURITY_VIOLATION           (0x00c1)
 #define MPI3_IOCSTATUS_INVALID_QUEUE_ID             (0x0f00)
 #define MPI3_IOCSTATUS_INVALID_QUEUE_SIZE           (0x0f01)
 #define MPI3_IOCSTATUS_INVALID_MSIX_VECTOR          (0x0f02)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi3mr.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi3mr.h
@@ -2,7 +2,7 @@
 /*
  * Driver for Broadcom MPI3 Storage Controllers
  *
- * Copyright (C) 2017-2021 Broadcom Inc.
+ * Copyright (C) 2017-2022 Broadcom Inc.
  *  (mailto: mpi3mr-linuxdrv.pdl@broadcom.com)
  *
  */
@@ -38,6 +38,8 @@
 #include <scsi/scsi_device.h>
 #include <scsi/scsi_host.h>
 #include <scsi/scsi_tcq.h>
+#include <scsi/scsi_transport_sas.h>
+#include <uapi/scsi/scsi_bsg_mpi3mr.h>
 
 #include "mpi/mpi30_transport.h"
 #include "mpi/mpi30_cnfg.h"
@@ -45,15 +47,17 @@
 #include "mpi/mpi30_init.h"
 #include "mpi/mpi30_ioc.h"
 #include "mpi/mpi30_sas.h"
+#include "mpi/mpi30_pci.h"
 #include "mpi3mr_debug.h"
 
 /* Global list and lock for storing multiple adapters managed by the driver */
 extern spinlock_t mrioc_list_lock;
 extern struct list_head mrioc_list;
 extern int prot_mask;
+extern atomic64_t event_counter;
 
-#define MPI3MR_DRIVER_VERSION	"00.255.45.01"
-#define MPI3MR_DRIVER_RELDATE	"12-December-2020"
+#define MPI3MR_DRIVER_VERSION	"8.0.0.69.0"
+#define MPI3MR_DRIVER_RELDATE	"16-March-2022"
 
 #define MPI3MR_DRIVER_NAME	"mpi3mr"
 #define MPI3MR_DRIVER_LICENSE	"GPL"
@@ -79,7 +83,8 @@
 
 /* Operational queue management definitions */
 #define MPI3MR_OP_REQ_Q_QD		512
-#define MPI3MR_OP_REP_Q_QD		4096
+#define MPI3MR_OP_REP_Q_QD		1024
+#define MPI3MR_OP_REP_Q_QD4K		4096
 #define MPI3MR_OP_REQ_Q_SEG_SIZE	4096
 #define MPI3MR_OP_REP_Q_SEG_SIZE	4096
 #define MPI3MR_MAX_SEG_LIST_SIZE	4096
@@ -87,31 +92,42 @@
 /* Reserved Host Tag definitions */
 #define MPI3MR_HOSTTAG_INVALID		0xFFFF
 #define MPI3MR_HOSTTAG_INITCMDS		1
-#define MPI3MR_HOSTTAG_IOCTLCMDS	2
+#define MPI3MR_HOSTTAG_BSG_CMDS		2
+#define MPI3MR_HOSTTAG_PEL_ABORT	3
+#define MPI3MR_HOSTTAG_PEL_WAIT		4
 #define MPI3MR_HOSTTAG_BLK_TMS		5
 
-#define MPI3MR_NUM_DEVRMCMD		1
+#define MPI3MR_NUM_DEVRMCMD		16
 #define MPI3MR_HOSTTAG_DEVRMCMD_MIN	(MPI3MR_HOSTTAG_BLK_TMS + 1)
 #define MPI3MR_HOSTTAG_DEVRMCMD_MAX	(MPI3MR_HOSTTAG_DEVRMCMD_MIN + \
 						MPI3MR_NUM_DEVRMCMD - 1)
 
-#define MPI3MR_INTERNAL_CMDS_RESVD     MPI3MR_HOSTTAG_DEVRMCMD_MAX
+#define MPI3MR_INTERNAL_CMDS_RESVD	MPI3MR_HOSTTAG_DEVRMCMD_MAX
+#define MPI3MR_NUM_EVTACKCMD		4
+#define MPI3MR_HOSTTAG_EVTACKCMD_MIN	(MPI3MR_HOSTTAG_DEVRMCMD_MAX + 1)
+#define MPI3MR_HOSTTAG_EVTACKCMD_MAX	(MPI3MR_HOSTTAG_EVTACKCMD_MIN + \
+					MPI3MR_NUM_EVTACKCMD - 1)
 
 /* Reduced resource count definition for crash kernel */
 #define MPI3MR_HOST_IOS_KDUMP		128
 
 /* command/controller interaction timeout definitions in seconds */
-#define MPI3MR_INTADMCMD_TIMEOUT		10
+#define MPI3MR_INTADMCMD_TIMEOUT		60
 #define MPI3MR_PORTENABLE_TIMEOUT		300
-#define MPI3MR_ABORTTM_TIMEOUT			30
-#define MPI3MR_RESETTM_TIMEOUT			30
+#define MPI3MR_ABORTTM_TIMEOUT			60
+#define MPI3MR_RESETTM_TIMEOUT			60
 #define MPI3MR_RESET_HOST_IOWAIT_TIMEOUT	5
 #define MPI3MR_TSUPDATE_INTERVAL		900
 #define MPI3MR_DEFAULT_SHUTDOWN_TIME		120
 #define	MPI3MR_RAID_ERRREC_RESET_TIMEOUT	180
+#define MPI3MR_PREPARE_FOR_RESET_TIMEOUT	180
+#define MPI3MR_RESET_ACK_TIMEOUT		30
 
 #define MPI3MR_WATCHDOG_INTERVAL		1000 /* in milli seconds */
 
+#define MPI3MR_SCMD_TIMEOUT    (60 * HZ)
+#define MPI3MR_EH_SCMD_TIMEOUT (60 * HZ)
+
 /* Internal admin command state definitions*/
 #define MPI3MR_CMD_NOTUSED	0x8000
 #define MPI3MR_CMD_COMPLETE	0x0001
@@ -121,7 +137,7 @@
 
 /* Definitions for Event replies and sense buffer allocated per controller */
 #define MPI3MR_NUM_EVT_REPLIES	64
-#define MPI3MR_SENSEBUF_SZ	256
+#define MPI3MR_SENSE_BUF_SZ	256
 #define MPI3MR_SENSEBUF_FACTOR	3
 #define MPI3MR_CHAINBUF_FACTOR	3
 #define MPI3MR_CHAINBUFDIX_FACTOR	2
@@ -135,19 +151,15 @@
 
 /* ResponseCode definitions */
 #define MPI3MR_RI_MASK_RESPCODE		(0x000000FF)
-#define MPI3MR_RSP_TM_COMPLETE		0x00
-#define MPI3MR_RSP_INVALID_FRAME	0x02
-#define MPI3MR_RSP_TM_NOT_SUPPORTED	0x04
-#define MPI3MR_RSP_TM_FAILED		0x05
-#define MPI3MR_RSP_TM_SUCCEEDED		0x08
-#define MPI3MR_RSP_TM_INVALID_LUN	0x09
-#define MPI3MR_RSP_TM_OVERLAPPED_TAG	0x0A
 #define MPI3MR_RSP_IO_QUEUED_ON_IOC \
 			MPI3_SCSITASKMGMT_RSPCODE_IO_QUEUED_ON_IOC
 
 #define MPI3MR_DEFAULT_MDTS	(128 * 1024)
+#define MPI3MR_DEFAULT_PGSZEXP         (12)
+
 /* Command retry count definitions */
 #define MPI3MR_DEV_RMHS_RETRY_COUNT 3
+#define MPI3MR_PEL_RETRY_COUNT 3
 
 /* Default target device queue depth */
 #define MPI3MR_DEFAULT_SDEV_QD	32
@@ -173,6 +185,57 @@
 /* MSI Index from Reply Queue Index */
 #define REPLY_QUEUE_IDX_TO_MSIX_IDX(qidx, offset)	(qidx + offset)
 
+/*
+ * Maximum data transfer size definitions for management
+ * application commands
+ */
+#define MPI3MR_MAX_APP_XFER_SIZE	(1 * 1024 * 1024)
+#define MPI3MR_MAX_APP_XFER_SEGMENTS	512
+/*
+ * 2048 sectors are for data buffers and additional 512 sectors for
+ * other buffers
+ */
+#define MPI3MR_MAX_APP_XFER_SECTORS	(2048 + 512)
+
+/**
+ * struct mpi3mr_nvme_pt_sge -  Structure to store SGEs for NVMe
+ * Encapsulated commands.
+ *
+ * @base_addr: Physical address
+ * @length: SGE length
+ * @rsvd: Reserved
+ * @rsvd1: Reserved
+ * @sgl_type: sgl type
+ */
+struct mpi3mr_nvme_pt_sge {
+	u64 base_addr;
+	u32 length;
+	u16 rsvd;
+	u8 rsvd1;
+	u8 sgl_type;
+};
+
+/**
+ * struct mpi3mr_buf_map -  local structure to
+ * track kernel and user buffers associated with an BSG
+ * structure.
+ *
+ * @bsg_buf: BSG buffer virtual address
+ * @bsg_buf_len:  BSG buffer length
+ * @kern_buf: Kernel buffer virtual address
+ * @kern_buf_len: Kernel buffer length
+ * @kern_buf_dma: Kernel buffer DMA address
+ * @data_dir: Data direction.
+ */
+struct mpi3mr_buf_map {
+	void *bsg_buf;
+	u32 bsg_buf_len;
+	void *kern_buf;
+	u32 kern_buf_len;
+	dma_addr_t kern_buf_dma;
+	u8 data_dir;
+};
+
 /* IOC State definitions */
 enum mpi3mr_iocstate {
 	MRIOC_STATE_READY = 1,
@@ -183,28 +246,14 @@
 	MRIOC_STATE_UNRECOVERABLE,
 };
 
-/* Init type definitions */
-enum mpi3mr_init_type {
-	MPI3MR_IT_INIT = 0,
-	MPI3MR_IT_RESET,
-	MPI3MR_IT_RESUME,
-};
-
-/* Cleanup reason definitions */
-enum mpi3mr_cleanup_reason {
-	MPI3MR_COMPLETE_CLEANUP = 0,
-	MPI3MR_REINIT_FAILURE,
-	MPI3MR_SUSPEND,
-};
-
 /* Reset reason code definitions*/
 enum mpi3mr_reset_reason {
 	MPI3MR_RESET_FROM_BRINGUP = 1,
 	MPI3MR_RESET_FROM_FAULT_WATCH = 2,
-	MPI3MR_RESET_FROM_IOCTL = 3,
+	MPI3MR_RESET_FROM_APP = 3,
 	MPI3MR_RESET_FROM_EH_HOS = 4,
 	MPI3MR_RESET_FROM_TM_TIMEOUT = 5,
-	MPI3MR_RESET_FROM_IOCTL_TIMEOUT = 6,
+	MPI3MR_RESET_FROM_APP_TIMEOUT = 6,
 	MPI3MR_RESET_FROM_MUR_FAILURE = 7,
 	MPI3MR_RESET_FROM_CTLR_CLEANUP = 8,
 	MPI3MR_RESET_FROM_CIACTIV_FAULT = 9,
@@ -222,7 +271,14 @@
 	MPI3MR_RESET_FROM_GETPKGVER_TIMEOUT = 21,
 	MPI3MR_RESET_FROM_PELABORT_TIMEOUT = 22,
 	MPI3MR_RESET_FROM_SYSFS = 23,
-	MPI3MR_RESET_FROM_SYSFS_TIMEOUT = 24
+	MPI3MR_RESET_FROM_SYSFS_TIMEOUT = 24,
+	MPI3MR_RESET_FROM_FIRMWARE = 27,
+};
+
+/* Queue type definitions */
+enum queue_type {
+	MPI3MR_DEFAULT_QUEUE = 0,
+	MPI3MR_POLL_QUEUE,
 };
 
 /**
@@ -263,7 +319,7 @@
 	u16 max_vds;
 	u16 max_hpds;
 	u16 max_advhpds;
-	u16 max_raidpds;
+	u16 max_raid_pds;
 	u16 min_devhandle;
 	u16 max_devhandle;
 	u16 max_op_req_q;
@@ -336,6 +392,7 @@
  * @pend_ios: Number of IOs pending in HW for this queue
  * @enable_irq_poll: Flag to indicate polling is enabled
  * @in_use: Queue is handled by poll/ISR
+ * @qtype: Type of queue (types defined in enum queue_type)
  */
 struct op_reply_qinfo {
 	u16 ci;
@@ -350,6 +407,7 @@
 	atomic_t pend_ios;
 	bool enable_irq_poll;
 	atomic_t in_use;
+	enum queue_type qtype;
 };
 
 /**
@@ -388,6 +446,7 @@
  * @pgsz: Device page size
  * @abort_to: Timeout for abort TM
  * @reset_to: Timeout for Target/LUN reset TM
+ * @dev_info: Device information bits
  */
 struct tgt_dev_pcie {
 	u32 mdts;
@@ -395,6 +454,7 @@
 	u8 pgsz;
 	u8 abort_to;
 	u8 reset_to;
+	u16 dev_info;
 };
 
 /**
@@ -499,6 +559,8 @@
  * @dev_removedelay: Device is waiting to be removed in FW
  * @dev_type: Device type
  * @tgt_dev: Internal target device pointer
+ * @pend_count: Counter to track pending I/Os during error
+ *		handling
  */
 struct mpi3mr_stgt_priv_data {
 	struct scsi_target *starget;
@@ -510,6 +572,7 @@
 	u8 dev_removedelay;
 	u8 dev_type;
 	struct mpi3mr_tgt_dev *tgt_dev;
+	u32 pend_count;
 };
 
 /**
@@ -518,11 +581,14 @@
  * @tgt_priv_data: Scsi_target private data pointer
  * @lun_id: LUN ID of the device
  * @ncq_prio_enable: NCQ priority enable for SATA device
+ * @pend_count: Counter to track pending I/Os during error
+ *		handling
  */
 struct mpi3mr_sdev_priv_data {
 	struct mpi3mr_stgt_priv_data *tgt_priv_data;
 	u32 lun_id;
 	u8 ncq_prio_enable;
+	u32 pend_count;
 };
 
 /**
@@ -538,6 +604,7 @@
  * @ioc_status: IOC status from the firmware
  * @ioc_loginfo:IOC log info from the firmware
  * @is_waiting: Is the command issued in block mode
+ * @is_sense: Is Sense data present
  * @retry_count: Retry count for retriable commands
  * @host_tag: Host tag used by the command
  * @callback: Callback for non blocking commands
@@ -553,6 +620,7 @@
 	u16 ioc_status;
 	u32 ioc_loginfo;
 	u8 is_waiting;
+	u8 is_sense;
 	u8 retry_count;
 	u16 host_tag;
 
@@ -630,6 +698,7 @@
  * @ready_timeout: Controller ready timeout
  * @intr_info: Interrupt cookie pointer
  * @intr_info_count: Number of interrupt cookies
+ * @is_intr_info_set: Flag to indicate intr info is setup
  * @num_queues: Number of operational queues
  * @num_op_req_q: Number of operational request queues
  * @req_qinfo: Operational request queue info pointer
@@ -679,26 +748,55 @@
  * @chain_bitmap_sz: Chain buffer allocator bitmap size
  * @chain_bitmap: Chain buffer allocator bitmap
  * @chain_buf_lock: Chain buffer list lock
+ * @bsg_cmds: Command tracker for BSG command
  * @host_tm_cmds: Command tracker for task management commands
  * @dev_rmhs_cmds: Command tracker for device removal commands
+ * @evtack_cmds: Command tracker for event ack commands
  * @devrem_bitmap_sz: Device removal bitmap size
  * @devrem_bitmap: Device removal bitmap
  * @dev_handle_bitmap_sz: Device handle bitmap size
  * @removepend_bitmap: Remove pending bitmap
  * @delayed_rmhs_list: Delayed device removal list
+ * @evtack_cmds_bitmap_sz: Event Ack bitmap size
+ * @evtack_cmds_bitmap: Event Ack bitmap
+ * @delayed_evtack_cmds_list: Delayed event acknowledgment list
  * @ts_update_counter: Timestamp update counter
- * @fault_dbg: Fault debug flag
  * @reset_in_progress: Reset in progress flag
  * @unrecoverable: Controller unrecoverable flag
+ * @prev_reset_result: Result of previous reset
  * @reset_mutex: Controller reset mutex
  * @reset_waitq: Controller reset  wait queue
+ * @prepare_for_reset: Prepare for reset event received
+ * @prepare_for_reset_timeout_counter: Prepare for reset timeout
+ * @prp_list_virt: NVMe encapsulated PRP list virtual base
+ * @prp_list_dma: NVMe encapsulated PRP list DMA
+ * @prp_sz: NVME encapsulated PRP list size
  * @diagsave_timeout: Diagnostic information save timeout
  * @logging_level: Controller debug logging level
  * @flush_io_count: I/O count to flush after reset
  * @current_event: Firmware event currently in process
  * @driver_info: Driver, Kernel, OS information to firmware
  * @change_count: Topology change count
+ * @pel_enabled: Persistent Event Log(PEL) enabled or not
+ * @pel_abort_requested: PEL abort is requested or not
+ * @pel_class: PEL Class identifier
+ * @pel_locale: PEL Locale identifier
+ * @pel_cmds: Command tracker for PEL wait command
+ * @pel_abort_cmd: Command tracker for PEL abort command
+ * @pel_newest_seqnum: Newest PEL sequenece number
+ * @pel_seqnum_virt: PEL sequence number virtual address
+ * @pel_seqnum_dma: PEL sequence number DMA address
+ * @pel_seqnum_sz: PEL sequenece number size
  * @op_reply_q_offset: Operational reply queue offset with MSIx
+ * @default_qcount: Total Default queues
+ * @active_poll_qcount: Currently active poll queue count
+ * @requested_poll_qcount: User requested poll queue count
+ * @bsg_dev: BSG device structure
+ * @bsg_queue: Request queue for BSG device
+ * @stop_bsgs: Stop BSG request flag
+ * @logdata_buf: Circular buffer to store log data entries
+ * @logdata_buf_idx: Index of entry in buffer to store
+ * @logdata_entry_sz: log data entry size
  */
 struct mpi3mr_ioc {
 	struct list_head list;
@@ -739,6 +837,7 @@
 
 	struct mpi3mr_intr_info *intr_info;
 	u16 intr_info_count;
+	bool is_intr_info_set;
 
 	u16 num_queues;
 	u16 num_op_req_q;
@@ -758,6 +857,7 @@
 	dma_addr_t reply_buf_dma_max_address;
 
 	u16 reply_free_qsz;
+	u16 reply_sz;
 	struct dma_pool *reply_free_q_pool;
 	__le64 *reply_free_q;
 	dma_addr_t reply_free_q_dma;
@@ -803,21 +903,33 @@
 	void *chain_bitmap;
 	spinlock_t chain_buf_lock;
 
+	struct mpi3mr_drv_cmd bsg_cmds;
 	struct mpi3mr_drv_cmd host_tm_cmds;
 	struct mpi3mr_drv_cmd dev_rmhs_cmds[MPI3MR_NUM_DEVRMCMD];
+	struct mpi3mr_drv_cmd evtack_cmds[MPI3MR_NUM_EVTACKCMD];
 	u16 devrem_bitmap_sz;
 	void *devrem_bitmap;
 	u16 dev_handle_bitmap_sz;
 	void *removepend_bitmap;
 	struct list_head delayed_rmhs_list;
+	u16 evtack_cmds_bitmap_sz;
+	void *evtack_cmds_bitmap;
+	struct list_head delayed_evtack_cmds_list;
 
 	u32 ts_update_counter;
-	u8 fault_dbg;
 	u8 reset_in_progress;
 	u8 unrecoverable;
+	int prev_reset_result;
 	struct mutex reset_mutex;
 	wait_queue_head_t reset_waitq;
 
+	u8 prepare_for_reset;
+	u16 prepare_for_reset_timeout_counter;
+
+	void *prp_list_virt;
+	dma_addr_t prp_list_dma;
+	u32 prp_sz;
+
 	u16 diagsave_timeout;
 	int logging_level;
 	u16 flush_io_count;
@@ -825,7 +937,30 @@
 	struct mpi3mr_fwevt *current_event;
 	struct mpi3_driver_info_layout driver_info;
 	u16 change_count;
+
+	u8 pel_enabled;
+	u8 pel_abort_requested;
+	u8 pel_class;
+	u16 pel_locale;
+	struct mpi3mr_drv_cmd pel_cmds;
+	struct mpi3mr_drv_cmd pel_abort_cmd;
+
+	u32 pel_newest_seqnum;
+	void *pel_seqnum_virt;
+	dma_addr_t pel_seqnum_dma;
+	u32 pel_seqnum_sz;
+
 	u16 op_reply_q_offset;
+	u16 default_qcount;
+	u16 active_poll_qcount;
+	u16 requested_poll_qcount;
+
+	struct device bsg_dev;
+	struct request_queue *bsg_queue;
+	u8 stop_bsgs;
+	u8 *logdata_buf;
+	u16 logdata_buf_idx;
+	u16 logdata_entry_sz;
 };
 
 /**
@@ -838,6 +973,9 @@
  * @send_ack: Event acknowledgment required or not
  * @process_evt: Bottomhalf processing required or not
  * @evt_ctx: Event context to send in Ack
+ * @event_data_size: size of the event data in bytes
+ * @pending_at_sml: waiting for device add/remove API to complete
+ * @discard: discard this event
  * @ref_count: kref count
  * @event_data: Actual MPI3 event data
  */
@@ -849,6 +987,9 @@
 	bool send_ack;
 	bool process_evt;
 	u32 evt_ctx;
+	u16 event_data_size;
+	bool pending_at_sml;
+	bool discard;
 	struct kref ref_count;
 	char event_data[0] __aligned(4);
 };
@@ -867,10 +1008,23 @@
 	u8 iou_rc;
 };
 
+/**
+ * struct delayed_evt_ack_node - Delayed event ack node
+ * @list: list head
+ * @event: MPI3 event ID
+ * @event_ctx: event context
+ */
+struct delayed_evt_ack_node {
+	struct list_head list;
+	u8 event;
+	u32 event_ctx;
+};
+
 int mpi3mr_setup_resources(struct mpi3mr_ioc *mrioc);
 void mpi3mr_cleanup_resources(struct mpi3mr_ioc *mrioc);
-int mpi3mr_init_ioc(struct mpi3mr_ioc *mrioc, u8 init_type);
-void mpi3mr_cleanup_ioc(struct mpi3mr_ioc *mrioc, u8 reason);
+int mpi3mr_init_ioc(struct mpi3mr_ioc *mrioc);
+int mpi3mr_reinit_ioc(struct mpi3mr_ioc *mrioc, u8 is_resume);
+void mpi3mr_cleanup_ioc(struct mpi3mr_ioc *mrioc);
 int mpi3mr_issue_port_enable(struct mpi3mr_ioc *mrioc, u8 async);
 int mpi3mr_admin_request_post(struct mpi3mr_ioc *mrioc, void *admin_req,
 u16 admin_req_sz, u8 ignore_reset);
@@ -887,6 +1041,7 @@
 				     u64 sense_buf_dma);
 
 void mpi3mr_memset_buffers(struct mpi3mr_ioc *mrioc);
+void mpi3mr_free_mem(struct mpi3mr_ioc *mrioc);
 void mpi3mr_os_handle_events(struct mpi3mr_ioc *mrioc,
 			     struct mpi3_event_notification_reply *event_reply);
 void mpi3mr_process_op_reply_desc(struct mpi3mr_ioc *mrioc,
@@ -897,13 +1052,11 @@
 
 int mpi3mr_soft_reset_handler(struct mpi3mr_ioc *mrioc,
 			      u32 reset_reason, u8 snapdump);
-int mpi3mr_diagfault_reset_handler(struct mpi3mr_ioc *mrioc,
-				   u32 reset_reason);
 void mpi3mr_ioc_disable_intr(struct mpi3mr_ioc *mrioc);
 void mpi3mr_ioc_enable_intr(struct mpi3mr_ioc *mrioc);
 
 enum mpi3mr_iocstate mpi3mr_get_iocstate(struct mpi3mr_ioc *mrioc);
-int mpi3mr_send_event_ack(struct mpi3mr_ioc *mrioc, u8 event,
+int mpi3mr_process_event_ack(struct mpi3mr_ioc *mrioc, u8 event,
 			  u32 event_ctx);
 
 void mpi3mr_wait_for_host_io(struct mpi3mr_ioc *mrioc, u32 timeout);
@@ -911,6 +1064,27 @@
 void mpi3mr_flush_host_io(struct mpi3mr_ioc *mrioc);
 void mpi3mr_invalidate_devhandles(struct mpi3mr_ioc *mrioc);
 void mpi3mr_rfresh_tgtdevs(struct mpi3mr_ioc *mrioc);
-void mpi3mr_flush_delayed_rmhs_list(struct mpi3mr_ioc *mrioc);
-
+void mpi3mr_flush_delayed_cmd_lists(struct mpi3mr_ioc *mrioc);
+void mpi3mr_check_rh_fault_ioc(struct mpi3mr_ioc *mrioc, u32 reason_code);
+void mpi3mr_print_fault_info(struct mpi3mr_ioc *mrioc);
+void mpi3mr_check_rh_fault_ioc(struct mpi3mr_ioc *mrioc, u32 reason_code);
+int mpi3mr_process_op_reply_q(struct mpi3mr_ioc *mrioc,
+	struct op_reply_qinfo *op_reply_q);
+int mpi3mr_blk_mq_poll(struct Scsi_Host *shost, unsigned int queue_num);
+void mpi3mr_bsg_init(struct mpi3mr_ioc *mrioc);
+void mpi3mr_bsg_exit(struct mpi3mr_ioc *mrioc);
+int mpi3mr_issue_tm(struct mpi3mr_ioc *mrioc, u8 tm_type,
+	u16 handle, uint lun, u16 htag, ulong timeout,
+	struct mpi3mr_drv_cmd *drv_cmd,
+	u8 *resp_code, struct scsi_cmnd *scmd);
+struct mpi3mr_tgt_dev *mpi3mr_get_tgtdev_by_handle(
+	struct mpi3mr_ioc *mrioc, u16 handle);
+void mpi3mr_pel_get_seqnum_complete(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd);
+int mpi3mr_pel_get_seqnum_post(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd);
+void mpi3mr_app_save_logdata(struct mpi3mr_ioc *mrioc, char *event_data,
+	u16 event_data_size);
+extern const struct attribute_group *mpi3mr_host_groups[];
+extern const struct attribute_group *mpi3mr_dev_groups[];
 #endif /*MPI3MR_H_INCLUDED*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi3mr_app.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi3mr_app.c
@@ -0,0 +1,1860 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for Broadcom MPI3 Storage Controllers
+ *
+ * Copyright (C) 2017-2022 Broadcom Inc.
+ *  (mailto: mpi3mr-linuxdrv.pdl@broadcom.com)
+ *
+ */
+
+#include "mpi3mr.h"
+#include <linux/bsg-lib.h>
+#include <uapi/scsi/scsi_bsg_mpi3mr.h>
+
+/**
+ * mpi3mr_bsg_pel_abort - sends PEL abort request
+ * @mrioc: Adapter instance reference
+ *
+ * This function sends PEL abort request to the firmware through
+ * admin request queue.
+ *
+ * Return: 0 on success, -1 on failure
+ */
+static int mpi3mr_bsg_pel_abort(struct mpi3mr_ioc *mrioc)
+{
+	struct mpi3_pel_req_action_abort pel_abort_req;
+	struct mpi3_pel_reply *pel_reply;
+	int retval = 0;
+	u16 pe_log_status;
+
+	if (mrioc->reset_in_progress) {
+		dprint_bsg_err(mrioc, "%s: reset in progress\n", __func__);
+		return -1;
+	}
+	if (mrioc->stop_bsgs) {
+		dprint_bsg_err(mrioc, "%s: bsgs are blocked\n", __func__);
+		return -1;
+	}
+
+	memset(&pel_abort_req, 0, sizeof(pel_abort_req));
+	mutex_lock(&mrioc->pel_abort_cmd.mutex);
+	if (mrioc->pel_abort_cmd.state & MPI3MR_CMD_PENDING) {
+		dprint_bsg_err(mrioc, "%s: command is in use\n", __func__);
+		mutex_unlock(&mrioc->pel_abort_cmd.mutex);
+		return -1;
+	}
+	mrioc->pel_abort_cmd.state = MPI3MR_CMD_PENDING;
+	mrioc->pel_abort_cmd.is_waiting = 1;
+	mrioc->pel_abort_cmd.callback = NULL;
+	pel_abort_req.host_tag = cpu_to_le16(MPI3MR_HOSTTAG_PEL_ABORT);
+	pel_abort_req.function = MPI3_FUNCTION_PERSISTENT_EVENT_LOG;
+	pel_abort_req.action = MPI3_PEL_ACTION_ABORT;
+	pel_abort_req.abort_host_tag = cpu_to_le16(MPI3MR_HOSTTAG_PEL_WAIT);
+
+	mrioc->pel_abort_requested = 1;
+	init_completion(&mrioc->pel_abort_cmd.done);
+	retval = mpi3mr_admin_request_post(mrioc, &pel_abort_req,
+	    sizeof(pel_abort_req), 0);
+	if (retval) {
+		retval = -1;
+		dprint_bsg_err(mrioc, "%s: admin request post failed\n",
+		    __func__);
+		mrioc->pel_abort_requested = 0;
+		goto out_unlock;
+	}
+
+	wait_for_completion_timeout(&mrioc->pel_abort_cmd.done,
+	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
+	if (!(mrioc->pel_abort_cmd.state & MPI3MR_CMD_COMPLETE)) {
+		mrioc->pel_abort_cmd.is_waiting = 0;
+		dprint_bsg_err(mrioc, "%s: command timedout\n", __func__);
+		if (!(mrioc->pel_abort_cmd.state & MPI3MR_CMD_RESET))
+			mpi3mr_soft_reset_handler(mrioc,
+			    MPI3MR_RESET_FROM_PELABORT_TIMEOUT, 1);
+		retval = -1;
+		goto out_unlock;
+	}
+	if ((mrioc->pel_abort_cmd.ioc_status & MPI3_IOCSTATUS_STATUS_MASK)
+	     != MPI3_IOCSTATUS_SUCCESS) {
+		dprint_bsg_err(mrioc,
+		    "%s: command failed, ioc_status(0x%04x) log_info(0x%08x)\n",
+		    __func__, (mrioc->pel_abort_cmd.ioc_status &
+		    MPI3_IOCSTATUS_STATUS_MASK),
+		    mrioc->pel_abort_cmd.ioc_loginfo);
+		retval = -1;
+		goto out_unlock;
+	}
+	if (mrioc->pel_abort_cmd.state & MPI3MR_CMD_REPLY_VALID) {
+		pel_reply = (struct mpi3_pel_reply *)mrioc->pel_abort_cmd.reply;
+		pe_log_status = le16_to_cpu(pel_reply->pe_log_status);
+		if (pe_log_status != MPI3_PEL_STATUS_SUCCESS) {
+			dprint_bsg_err(mrioc,
+			    "%s: command failed, pel_status(0x%04x)\n",
+			    __func__, pe_log_status);
+			retval = -1;
+		}
+	}
+
+out_unlock:
+	mrioc->pel_abort_cmd.state = MPI3MR_CMD_NOTUSED;
+	mutex_unlock(&mrioc->pel_abort_cmd.mutex);
+	return retval;
+}
+/**
+ * mpi3mr_bsg_verify_adapter - verify adapter number is valid
+ * @ioc_number: Adapter number
+ *
+ * This function returns the adapter instance pointer of given
+ * adapter number. If adapter number does not match with the
+ * driver's adapter list, driver returns NULL.
+ *
+ * Return: adapter instance reference
+ */
+static struct mpi3mr_ioc *mpi3mr_bsg_verify_adapter(int ioc_number)
+{
+	struct mpi3mr_ioc *mrioc = NULL;
+
+	spin_lock(&mrioc_list_lock);
+	list_for_each_entry(mrioc, &mrioc_list, list) {
+		if (mrioc->id == ioc_number) {
+			spin_unlock(&mrioc_list_lock);
+			return mrioc;
+		}
+	}
+	spin_unlock(&mrioc_list_lock);
+	return NULL;
+}
+
+/**
+ * mpi3mr_enable_logdata - Handler for log data enable
+ * @mrioc: Adapter instance reference
+ * @job: BSG job reference
+ *
+ * This function enables log data caching in the driver if not
+ * already enabled and return the maximum number of log data
+ * entries that can be cached in the driver.
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_enable_logdata(struct mpi3mr_ioc *mrioc,
+	struct bsg_job *job)
+{
+	struct mpi3mr_logdata_enable logdata_enable;
+
+	if (!mrioc->logdata_buf) {
+		mrioc->logdata_entry_sz =
+		    (mrioc->reply_sz - (sizeof(struct mpi3_event_notification_reply) - 4))
+		    + MPI3MR_BSG_LOGDATA_ENTRY_HEADER_SZ;
+		mrioc->logdata_buf_idx = 0;
+		mrioc->logdata_buf = kcalloc(MPI3MR_BSG_LOGDATA_MAX_ENTRIES,
+		    mrioc->logdata_entry_sz, GFP_KERNEL);
+
+		if (!mrioc->logdata_buf)
+			return -ENOMEM;
+	}
+
+	memset(&logdata_enable, 0, sizeof(logdata_enable));
+	logdata_enable.max_entries =
+	    MPI3MR_BSG_LOGDATA_MAX_ENTRIES;
+	if (job->request_payload.payload_len >= sizeof(logdata_enable)) {
+		sg_copy_from_buffer(job->request_payload.sg_list,
+				    job->request_payload.sg_cnt,
+				    &logdata_enable, sizeof(logdata_enable));
+		return 0;
+	}
+
+	return -EINVAL;
+}
+/**
+ * mpi3mr_get_logdata - Handler for get log data
+ * @mrioc: Adapter instance reference
+ * @job: BSG job pointer
+ * This function copies the log data entries to the user buffer
+ * when log caching is enabled in the driver.
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_get_logdata(struct mpi3mr_ioc *mrioc,
+	struct bsg_job *job)
+{
+	u16 num_entries, sz, entry_sz = mrioc->logdata_entry_sz;
+
+	if ((!mrioc->logdata_buf) || (job->request_payload.payload_len < entry_sz))
+		return -EINVAL;
+
+	num_entries = job->request_payload.payload_len / entry_sz;
+	if (num_entries > MPI3MR_BSG_LOGDATA_MAX_ENTRIES)
+		num_entries = MPI3MR_BSG_LOGDATA_MAX_ENTRIES;
+	sz = num_entries * entry_sz;
+
+	if (job->request_payload.payload_len >= sz) {
+		sg_copy_from_buffer(job->request_payload.sg_list,
+				    job->request_payload.sg_cnt,
+				    mrioc->logdata_buf, sz);
+		return 0;
+	}
+	return -EINVAL;
+}
+
+/**
+ * mpi3mr_bsg_pel_enable - Handler for PEL enable driver
+ * @mrioc: Adapter instance reference
+ * @job: BSG job pointer
+ *
+ * This function is the handler for PEL enable driver.
+ * Validates the application given class and locale and if
+ * requires aborts the existing PEL wait request and/or issues
+ * new PEL wait request to the firmware and returns.
+ *
+ * Return: 0 on success and proper error codes on failure.
+ */
+static long mpi3mr_bsg_pel_enable(struct mpi3mr_ioc *mrioc,
+				  struct bsg_job *job)
+{
+	long rval = -EINVAL;
+	struct mpi3mr_bsg_out_pel_enable pel_enable;
+	u8 issue_pel_wait;
+	u8 tmp_class;
+	u16 tmp_locale;
+
+	if (job->request_payload.payload_len != sizeof(pel_enable)) {
+		dprint_bsg_err(mrioc, "%s: invalid size argument\n",
+		    __func__);
+		return rval;
+	}
+
+	sg_copy_to_buffer(job->request_payload.sg_list,
+			  job->request_payload.sg_cnt,
+			  &pel_enable, sizeof(pel_enable));
+
+	if (pel_enable.pel_class > MPI3_PEL_CLASS_FAULT) {
+		dprint_bsg_err(mrioc, "%s: out of range class %d sent\n",
+			__func__, pel_enable.pel_class);
+		rval = 0;
+		goto out;
+	}
+	if (!mrioc->pel_enabled)
+		issue_pel_wait = 1;
+	else {
+		if ((mrioc->pel_class <= pel_enable.pel_class) &&
+		    !((mrioc->pel_locale & pel_enable.pel_locale) ^
+		      pel_enable.pel_locale)) {
+			issue_pel_wait = 0;
+			rval = 0;
+		} else {
+			pel_enable.pel_locale |= mrioc->pel_locale;
+
+			if (mrioc->pel_class < pel_enable.pel_class)
+				pel_enable.pel_class = mrioc->pel_class;
+
+			rval = mpi3mr_bsg_pel_abort(mrioc);
+			if (rval) {
+				dprint_bsg_err(mrioc,
+				    "%s: pel_abort failed, status(%ld)\n",
+				    __func__, rval);
+				goto out;
+			}
+			issue_pel_wait = 1;
+		}
+	}
+	if (issue_pel_wait) {
+		tmp_class = mrioc->pel_class;
+		tmp_locale = mrioc->pel_locale;
+		mrioc->pel_class = pel_enable.pel_class;
+		mrioc->pel_locale = pel_enable.pel_locale;
+		mrioc->pel_enabled = 1;
+		rval = mpi3mr_pel_get_seqnum_post(mrioc, NULL);
+		if (rval) {
+			mrioc->pel_class = tmp_class;
+			mrioc->pel_locale = tmp_locale;
+			mrioc->pel_enabled = 0;
+			dprint_bsg_err(mrioc,
+			    "%s: pel get sequence number failed, status(%ld)\n",
+			    __func__, rval);
+		}
+	}
+
+out:
+	return rval;
+}
+/**
+ * mpi3mr_get_all_tgt_info - Get all target information
+ * @mrioc: Adapter instance reference
+ * @job: BSG job reference
+ *
+ * This function copies the driver managed target devices device
+ * handle, persistent ID, bus ID and taret ID to the user
+ * provided buffer for the specific controller. This function
+ * also provides the number of devices managed by the driver for
+ * the specific controller.
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_get_all_tgt_info(struct mpi3mr_ioc *mrioc,
+	struct bsg_job *job)
+{
+	long rval = -EINVAL;
+	u16 num_devices = 0, i = 0, size;
+	unsigned long flags;
+	struct mpi3mr_tgt_dev *tgtdev;
+	struct mpi3mr_device_map_info *devmap_info = NULL;
+	struct mpi3mr_all_tgt_info *alltgt_info = NULL;
+	uint32_t min_entrylen = 0, kern_entrylen = 0, usr_entrylen = 0;
+
+	if (job->request_payload.payload_len < sizeof(u32)) {
+		dprint_bsg_err(mrioc, "%s: invalid size argument\n",
+		    __func__);
+		return rval;
+	}
+
+	spin_lock_irqsave(&mrioc->tgtdev_lock, flags);
+	list_for_each_entry(tgtdev, &mrioc->tgtdev_list, list)
+		num_devices++;
+	spin_unlock_irqrestore(&mrioc->tgtdev_lock, flags);
+
+	if ((job->request_payload.payload_len == sizeof(u32)) ||
+		list_empty(&mrioc->tgtdev_list)) {
+		sg_copy_from_buffer(job->request_payload.sg_list,
+				    job->request_payload.sg_cnt,
+				    &num_devices, sizeof(num_devices));
+		return 0;
+	}
+
+	kern_entrylen = (num_devices - 1) * sizeof(*devmap_info);
+	size = sizeof(*alltgt_info) + kern_entrylen;
+	alltgt_info = kzalloc(size, GFP_KERNEL);
+	if (!alltgt_info)
+		return -ENOMEM;
+
+	devmap_info = alltgt_info->dmi;
+	memset((u8 *)devmap_info, 0xFF, (kern_entrylen + sizeof(*devmap_info)));
+	spin_lock_irqsave(&mrioc->tgtdev_lock, flags);
+	list_for_each_entry(tgtdev, &mrioc->tgtdev_list, list) {
+		if (i < num_devices) {
+			devmap_info[i].handle = tgtdev->dev_handle;
+			devmap_info[i].perst_id = tgtdev->perst_id;
+			if (tgtdev->host_exposed && tgtdev->starget) {
+				devmap_info[i].target_id = tgtdev->starget->id;
+				devmap_info[i].bus_id =
+				    tgtdev->starget->channel;
+			}
+			i++;
+		}
+	}
+	num_devices = i;
+	spin_unlock_irqrestore(&mrioc->tgtdev_lock, flags);
+
+	memcpy(&alltgt_info->num_devices, &num_devices, sizeof(num_devices));
+
+	usr_entrylen = (job->request_payload.payload_len - sizeof(u32)) / sizeof(*devmap_info);
+	usr_entrylen *= sizeof(*devmap_info);
+	min_entrylen = min(usr_entrylen, kern_entrylen);
+	if (min_entrylen && (!memcpy(&alltgt_info->dmi, devmap_info, min_entrylen))) {
+		dprint_bsg_err(mrioc, "%s:%d: device map info copy failed\n",
+		    __func__, __LINE__);
+		rval = -EFAULT;
+		goto out;
+	}
+
+	sg_copy_from_buffer(job->request_payload.sg_list,
+			    job->request_payload.sg_cnt,
+			    alltgt_info, job->request_payload.payload_len);
+	rval = 0;
+out:
+	kfree(alltgt_info);
+	return rval;
+}
+/**
+ * mpi3mr_get_change_count - Get topology change count
+ * @mrioc: Adapter instance reference
+ * @job: BSG job reference
+ *
+ * This function copies the toplogy change count provided by the
+ * driver in events and cached in the driver to the user
+ * provided buffer for the specific controller.
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_get_change_count(struct mpi3mr_ioc *mrioc,
+	struct bsg_job *job)
+{
+	struct mpi3mr_change_count chgcnt;
+
+	memset(&chgcnt, 0, sizeof(chgcnt));
+	chgcnt.change_count = mrioc->change_count;
+	if (job->request_payload.payload_len >= sizeof(chgcnt)) {
+		sg_copy_from_buffer(job->request_payload.sg_list,
+				    job->request_payload.sg_cnt,
+				    &chgcnt, sizeof(chgcnt));
+		return 0;
+	}
+	return -EINVAL;
+}
+
+/**
+ * mpi3mr_bsg_adp_reset - Issue controller reset
+ * @mrioc: Adapter instance reference
+ * @job: BSG job reference
+ *
+ * This function identifies the user provided reset type and
+ * issues approporiate reset to the controller and wait for that
+ * to complete and reinitialize the controller and then returns
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_bsg_adp_reset(struct mpi3mr_ioc *mrioc,
+	struct bsg_job *job)
+{
+	long rval = -EINVAL;
+	u8 save_snapdump;
+	struct mpi3mr_bsg_adp_reset adpreset;
+
+	if (job->request_payload.payload_len !=
+			sizeof(adpreset)) {
+		dprint_bsg_err(mrioc, "%s: invalid size argument\n",
+		    __func__);
+		goto out;
+	}
+
+	sg_copy_to_buffer(job->request_payload.sg_list,
+			  job->request_payload.sg_cnt,
+			  &adpreset, sizeof(adpreset));
+
+	switch (adpreset.reset_type) {
+	case MPI3MR_BSG_ADPRESET_SOFT:
+		save_snapdump = 0;
+		break;
+	case MPI3MR_BSG_ADPRESET_DIAG_FAULT:
+		save_snapdump = 1;
+		break;
+	default:
+		dprint_bsg_err(mrioc, "%s: unknown reset_type(%d)\n",
+		    __func__, adpreset.reset_type);
+		goto out;
+	}
+
+	rval = mpi3mr_soft_reset_handler(mrioc, MPI3MR_RESET_FROM_APP,
+	    save_snapdump);
+
+	if (rval)
+		dprint_bsg_err(mrioc,
+		    "%s: reset handler returned error(%ld) for reset type %d\n",
+		    __func__, rval, adpreset.reset_type);
+out:
+	return rval;
+}
+
+/**
+ * mpi3mr_bsg_populate_adpinfo - Get adapter info command handler
+ * @mrioc: Adapter instance reference
+ * @job: BSG job reference
+ *
+ * This function provides adapter information for the given
+ * controller
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_bsg_populate_adpinfo(struct mpi3mr_ioc *mrioc,
+	struct bsg_job *job)
+{
+	enum mpi3mr_iocstate ioc_state;
+	struct mpi3mr_bsg_in_adpinfo adpinfo;
+
+	memset(&adpinfo, 0, sizeof(adpinfo));
+	adpinfo.adp_type = MPI3MR_BSG_ADPTYPE_AVGFAMILY;
+	adpinfo.pci_dev_id = mrioc->pdev->device;
+	adpinfo.pci_dev_hw_rev = mrioc->pdev->revision;
+	adpinfo.pci_subsys_dev_id = mrioc->pdev->subsystem_device;
+	adpinfo.pci_subsys_ven_id = mrioc->pdev->subsystem_vendor;
+	adpinfo.pci_bus = mrioc->pdev->bus->number;
+	adpinfo.pci_dev = PCI_SLOT(mrioc->pdev->devfn);
+	adpinfo.pci_func = PCI_FUNC(mrioc->pdev->devfn);
+	adpinfo.pci_seg_id = pci_domain_nr(mrioc->pdev->bus);
+	adpinfo.app_intfc_ver = MPI3MR_IOCTL_VERSION;
+
+	ioc_state = mpi3mr_get_iocstate(mrioc);
+	if (ioc_state == MRIOC_STATE_UNRECOVERABLE)
+		adpinfo.adp_state = MPI3MR_BSG_ADPSTATE_UNRECOVERABLE;
+	else if ((mrioc->reset_in_progress) || (mrioc->stop_bsgs))
+		adpinfo.adp_state = MPI3MR_BSG_ADPSTATE_IN_RESET;
+	else if (ioc_state == MRIOC_STATE_FAULT)
+		adpinfo.adp_state = MPI3MR_BSG_ADPSTATE_FAULT;
+	else
+		adpinfo.adp_state = MPI3MR_BSG_ADPSTATE_OPERATIONAL;
+
+	memcpy((u8 *)&adpinfo.driver_info, (u8 *)&mrioc->driver_info,
+	    sizeof(adpinfo.driver_info));
+
+	if (job->request_payload.payload_len >= sizeof(adpinfo)) {
+		sg_copy_from_buffer(job->request_payload.sg_list,
+				    job->request_payload.sg_cnt,
+				    &adpinfo, sizeof(adpinfo));
+		return 0;
+	}
+	return -EINVAL;
+}
+
+/**
+ * mpi3mr_bsg_process_drv_cmds - Driver Command handler
+ * @job: BSG job reference
+ *
+ * This function is the top level handler for driver commands,
+ * this does basic validation of the buffer and identifies the
+ * opcode and switches to correct sub handler.
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static long mpi3mr_bsg_process_drv_cmds(struct bsg_job *job)
+{
+	long rval = -EINVAL;
+	struct mpi3mr_ioc *mrioc = NULL;
+	struct mpi3mr_bsg_packet *bsg_req = NULL;
+	struct mpi3mr_bsg_drv_cmd *drvrcmd = NULL;
+
+	bsg_req = job->request;
+	drvrcmd = &bsg_req->cmd.drvrcmd;
+
+	mrioc = mpi3mr_bsg_verify_adapter(drvrcmd->mrioc_id);
+	if (!mrioc)
+		return -ENODEV;
+
+	if (drvrcmd->opcode == MPI3MR_DRVBSG_OPCODE_ADPINFO) {
+		rval = mpi3mr_bsg_populate_adpinfo(mrioc, job);
+		return rval;
+	}
+
+	if (mutex_lock_interruptible(&mrioc->bsg_cmds.mutex))
+		return -ERESTARTSYS;
+
+	switch (drvrcmd->opcode) {
+	case MPI3MR_DRVBSG_OPCODE_ADPRESET:
+		rval = mpi3mr_bsg_adp_reset(mrioc, job);
+		break;
+	case MPI3MR_DRVBSG_OPCODE_ALLTGTDEVINFO:
+		rval = mpi3mr_get_all_tgt_info(mrioc, job);
+		break;
+	case MPI3MR_DRVBSG_OPCODE_GETCHGCNT:
+		rval = mpi3mr_get_change_count(mrioc, job);
+		break;
+	case MPI3MR_DRVBSG_OPCODE_LOGDATAENABLE:
+		rval = mpi3mr_enable_logdata(mrioc, job);
+		break;
+	case MPI3MR_DRVBSG_OPCODE_GETLOGDATA:
+		rval = mpi3mr_get_logdata(mrioc, job);
+		break;
+	case MPI3MR_DRVBSG_OPCODE_PELENABLE:
+		rval = mpi3mr_bsg_pel_enable(mrioc, job);
+		break;
+	case MPI3MR_DRVBSG_OPCODE_UNKNOWN:
+	default:
+		pr_err("%s: unsupported driver command opcode %d\n",
+		    MPI3MR_DRIVER_NAME, drvrcmd->opcode);
+		break;
+	}
+	mutex_unlock(&mrioc->bsg_cmds.mutex);
+	return rval;
+}
+
+/**
+ * mpi3mr_bsg_build_sgl - SGL construction for MPI commands
+ * @mpi_req: MPI request
+ * @sgl_offset: offset to start sgl in the MPI request
+ * @drv_bufs: DMA address of the buffers to be placed in sgl
+ * @bufcnt: Number of DMA buffers
+ * @is_rmc: Does the buffer list has management command buffer
+ * @is_rmr: Does the buffer list has management response buffer
+ * @num_datasges: Number of data buffers in the list
+ *
+ * This function places the DMA address of the given buffers in
+ * proper format as SGEs in the given MPI request.
+ *
+ * Return: Nothing
+ */
+static void mpi3mr_bsg_build_sgl(u8 *mpi_req, uint32_t sgl_offset,
+	struct mpi3mr_buf_map *drv_bufs, u8 bufcnt, u8 is_rmc,
+	u8 is_rmr, u8 num_datasges)
+{
+	u8 *sgl = (mpi_req + sgl_offset), count = 0;
+	struct mpi3_mgmt_passthrough_request *rmgmt_req =
+	    (struct mpi3_mgmt_passthrough_request *)mpi_req;
+	struct mpi3mr_buf_map *drv_buf_iter = drv_bufs;
+	u8 sgl_flags, sgl_flags_last;
+
+	sgl_flags = MPI3_SGE_FLAGS_ELEMENT_TYPE_SIMPLE |
+		MPI3_SGE_FLAGS_DLAS_SYSTEM | MPI3_SGE_FLAGS_END_OF_BUFFER;
+	sgl_flags_last = sgl_flags | MPI3_SGE_FLAGS_END_OF_LIST;
+
+	if (is_rmc) {
+		mpi3mr_add_sg_single(&rmgmt_req->command_sgl,
+		    sgl_flags_last, drv_buf_iter->kern_buf_len,
+		    drv_buf_iter->kern_buf_dma);
+		sgl = (u8 *)drv_buf_iter->kern_buf + drv_buf_iter->bsg_buf_len;
+		drv_buf_iter++;
+		count++;
+		if (is_rmr) {
+			mpi3mr_add_sg_single(&rmgmt_req->response_sgl,
+			    sgl_flags_last, drv_buf_iter->kern_buf_len,
+			    drv_buf_iter->kern_buf_dma);
+			drv_buf_iter++;
+			count++;
+		} else
+			mpi3mr_build_zero_len_sge(
+			    &rmgmt_req->response_sgl);
+	}
+	if (!num_datasges) {
+		mpi3mr_build_zero_len_sge(sgl);
+		return;
+	}
+	for (; count < bufcnt; count++, drv_buf_iter++) {
+		if (drv_buf_iter->data_dir == DMA_NONE)
+			continue;
+		if (num_datasges == 1 || !is_rmc)
+			mpi3mr_add_sg_single(sgl, sgl_flags_last,
+			    drv_buf_iter->kern_buf_len, drv_buf_iter->kern_buf_dma);
+		else
+			mpi3mr_add_sg_single(sgl, sgl_flags,
+			    drv_buf_iter->kern_buf_len, drv_buf_iter->kern_buf_dma);
+		sgl += sizeof(struct mpi3_sge_common);
+		num_datasges--;
+	}
+}
+
+/**
+ * mpi3mr_get_nvme_data_fmt - returns the NVMe data format
+ * @nvme_encap_request: NVMe encapsulated MPI request
+ *
+ * This function returns the type of the data format specified
+ * in user provided NVMe command in NVMe encapsulated request.
+ *
+ * Return: Data format of the NVMe command (PRP/SGL etc)
+ */
+static unsigned int mpi3mr_get_nvme_data_fmt(
+	struct mpi3_nvme_encapsulated_request *nvme_encap_request)
+{
+	u8 format = 0;
+
+	format = ((nvme_encap_request->command[0] & 0xc000) >> 14);
+	return format;
+
+}
+
+/**
+ * mpi3mr_build_nvme_sgl - SGL constructor for NVME
+ *				   encapsulated request
+ * @mrioc: Adapter instance reference
+ * @nvme_encap_request: NVMe encapsulated MPI request
+ * @drv_bufs: DMA address of the buffers to be placed in sgl
+ * @bufcnt: Number of DMA buffers
+ *
+ * This function places the DMA address of the given buffers in
+ * proper format as SGEs in the given NVMe encapsulated request.
+ *
+ * Return: 0 on success, -1 on failure
+ */
+static int mpi3mr_build_nvme_sgl(struct mpi3mr_ioc *mrioc,
+	struct mpi3_nvme_encapsulated_request *nvme_encap_request,
+	struct mpi3mr_buf_map *drv_bufs, u8 bufcnt)
+{
+	struct mpi3mr_nvme_pt_sge *nvme_sgl;
+	u64 sgl_ptr;
+	u8 count;
+	size_t length = 0;
+	struct mpi3mr_buf_map *drv_buf_iter = drv_bufs;
+	u64 sgemod_mask = ((u64)((mrioc->facts.sge_mod_mask) <<
+			    mrioc->facts.sge_mod_shift) << 32);
+	u64 sgemod_val = ((u64)(mrioc->facts.sge_mod_value) <<
+			  mrioc->facts.sge_mod_shift) << 32;
+
+	/*
+	 * Not all commands require a data transfer. If no data, just return
+	 * without constructing any sgl.
+	 */
+	for (count = 0; count < bufcnt; count++, drv_buf_iter++) {
+		if (drv_buf_iter->data_dir == DMA_NONE)
+			continue;
+		sgl_ptr = (u64)drv_buf_iter->kern_buf_dma;
+		length = drv_buf_iter->kern_buf_len;
+		break;
+	}
+	if (!length)
+		return 0;
+
+	if (sgl_ptr & sgemod_mask) {
+		dprint_bsg_err(mrioc,
+		    "%s: SGL address collides with SGE modifier\n",
+		    __func__);
+		return -1;
+	}
+
+	sgl_ptr &= ~sgemod_mask;
+	sgl_ptr |= sgemod_val;
+	nvme_sgl = (struct mpi3mr_nvme_pt_sge *)
+	    ((u8 *)(nvme_encap_request->command) + MPI3MR_NVME_CMD_SGL_OFFSET);
+	memset(nvme_sgl, 0, sizeof(struct mpi3mr_nvme_pt_sge));
+	nvme_sgl->base_addr = sgl_ptr;
+	nvme_sgl->length = length;
+	return 0;
+}
+
+/**
+ * mpi3mr_build_nvme_prp - PRP constructor for NVME
+ *			       encapsulated request
+ * @mrioc: Adapter instance reference
+ * @nvme_encap_request: NVMe encapsulated MPI request
+ * @drv_bufs: DMA address of the buffers to be placed in SGL
+ * @bufcnt: Number of DMA buffers
+ *
+ * This function places the DMA address of the given buffers in
+ * proper format as PRP entries in the given NVMe encapsulated
+ * request.
+ *
+ * Return: 0 on success, -1 on failure
+ */
+static int mpi3mr_build_nvme_prp(struct mpi3mr_ioc *mrioc,
+	struct mpi3_nvme_encapsulated_request *nvme_encap_request,
+	struct mpi3mr_buf_map *drv_bufs, u8 bufcnt)
+{
+	int prp_size = MPI3MR_NVME_PRP_SIZE;
+	__le64 *prp_entry, *prp1_entry, *prp2_entry;
+	__le64 *prp_page;
+	dma_addr_t prp_entry_dma, prp_page_dma, dma_addr;
+	u32 offset, entry_len, dev_pgsz;
+	u32 page_mask_result, page_mask;
+	size_t length = 0;
+	u8 count;
+	struct mpi3mr_buf_map *drv_buf_iter = drv_bufs;
+	u64 sgemod_mask = ((u64)((mrioc->facts.sge_mod_mask) <<
+			    mrioc->facts.sge_mod_shift) << 32);
+	u64 sgemod_val = ((u64)(mrioc->facts.sge_mod_value) <<
+			  mrioc->facts.sge_mod_shift) << 32;
+	u16 dev_handle = nvme_encap_request->dev_handle;
+	struct mpi3mr_tgt_dev *tgtdev;
+
+	tgtdev = mpi3mr_get_tgtdev_by_handle(mrioc, dev_handle);
+	if (!tgtdev) {
+		dprint_bsg_err(mrioc, "%s: invalid device handle 0x%04x\n",
+			__func__, dev_handle);
+		return -1;
+	}
+
+	if (tgtdev->dev_spec.pcie_inf.pgsz == 0) {
+		dprint_bsg_err(mrioc,
+		    "%s: NVMe device page size is zero for handle 0x%04x\n",
+		    __func__, dev_handle);
+		mpi3mr_tgtdev_put(tgtdev);
+		return -1;
+	}
+
+	dev_pgsz = 1 << (tgtdev->dev_spec.pcie_inf.pgsz);
+	mpi3mr_tgtdev_put(tgtdev);
+
+	/*
+	 * Not all commands require a data transfer. If no data, just return
+	 * without constructing any PRP.
+	 */
+	for (count = 0; count < bufcnt; count++, drv_buf_iter++) {
+		if (drv_buf_iter->data_dir == DMA_NONE)
+			continue;
+		dma_addr = drv_buf_iter->kern_buf_dma;
+		length = drv_buf_iter->kern_buf_len;
+		break;
+	}
+
+	if (!length)
+		return 0;
+
+	mrioc->prp_sz = 0;
+	mrioc->prp_list_virt = dma_alloc_coherent(&mrioc->pdev->dev,
+	    dev_pgsz, &mrioc->prp_list_dma, GFP_KERNEL);
+
+	if (!mrioc->prp_list_virt)
+		return -1;
+	mrioc->prp_sz = dev_pgsz;
+
+	/*
+	 * Set pointers to PRP1 and PRP2, which are in the NVMe command.
+	 * PRP1 is located at a 24 byte offset from the start of the NVMe
+	 * command.  Then set the current PRP entry pointer to PRP1.
+	 */
+	prp1_entry = (__le64 *)((u8 *)(nvme_encap_request->command) +
+	    MPI3MR_NVME_CMD_PRP1_OFFSET);
+	prp2_entry = (__le64 *)((u8 *)(nvme_encap_request->command) +
+	    MPI3MR_NVME_CMD_PRP2_OFFSET);
+	prp_entry = prp1_entry;
+	/*
+	 * For the PRP entries, use the specially allocated buffer of
+	 * contiguous memory.
+	 */
+	prp_page = (__le64 *)mrioc->prp_list_virt;
+	prp_page_dma = mrioc->prp_list_dma;
+
+	/*
+	 * Check if we are within 1 entry of a page boundary we don't
+	 * want our first entry to be a PRP List entry.
+	 */
+	page_mask = dev_pgsz - 1;
+	page_mask_result = (uintptr_t)((u8 *)prp_page + prp_size) & page_mask;
+	if (!page_mask_result) {
+		dprint_bsg_err(mrioc, "%s: PRP page is not page aligned\n",
+		    __func__);
+		goto err_out;
+	}
+
+	/*
+	 * Set PRP physical pointer, which initially points to the current PRP
+	 * DMA memory page.
+	 */
+	prp_entry_dma = prp_page_dma;
+
+
+	/* Loop while the length is not zero. */
+	while (length) {
+		page_mask_result = (prp_entry_dma + prp_size) & page_mask;
+		if (!page_mask_result && (length >  dev_pgsz)) {
+			dprint_bsg_err(mrioc,
+			    "%s: single PRP page is not sufficient\n",
+			    __func__);
+			goto err_out;
+		}
+
+		/* Need to handle if entry will be part of a page. */
+		offset = dma_addr & page_mask;
+		entry_len = dev_pgsz - offset;
+
+		if (prp_entry == prp1_entry) {
+			/*
+			 * Must fill in the first PRP pointer (PRP1) before
+			 * moving on.
+			 */
+			*prp1_entry = cpu_to_le64(dma_addr);
+			if (*prp1_entry & sgemod_mask) {
+				dprint_bsg_err(mrioc,
+				    "%s: PRP1 address collides with SGE modifier\n",
+				    __func__);
+				goto err_out;
+			}
+			*prp1_entry &= ~sgemod_mask;
+			*prp1_entry |= sgemod_val;
+
+			/*
+			 * Now point to the second PRP entry within the
+			 * command (PRP2).
+			 */
+			prp_entry = prp2_entry;
+		} else if (prp_entry == prp2_entry) {
+			/*
+			 * Should the PRP2 entry be a PRP List pointer or just
+			 * a regular PRP pointer?  If there is more than one
+			 * more page of data, must use a PRP List pointer.
+			 */
+			if (length > dev_pgsz) {
+				/*
+				 * PRP2 will contain a PRP List pointer because
+				 * more PRP's are needed with this command. The
+				 * list will start at the beginning of the
+				 * contiguous buffer.
+				 */
+				*prp2_entry = cpu_to_le64(prp_entry_dma);
+				if (*prp2_entry & sgemod_mask) {
+					dprint_bsg_err(mrioc,
+					    "%s: PRP list address collides with SGE modifier\n",
+					    __func__);
+					goto err_out;
+				}
+				*prp2_entry &= ~sgemod_mask;
+				*prp2_entry |= sgemod_val;
+
+				/*
+				 * The next PRP Entry will be the start of the
+				 * first PRP List.
+				 */
+				prp_entry = prp_page;
+				continue;
+			} else {
+				/*
+				 * After this, the PRP Entries are complete.
+				 * This command uses 2 PRP's and no PRP list.
+				 */
+				*prp2_entry = cpu_to_le64(dma_addr);
+				if (*prp2_entry & sgemod_mask) {
+					dprint_bsg_err(mrioc,
+					    "%s: PRP2 collides with SGE modifier\n",
+					    __func__);
+					goto err_out;
+				}
+				*prp2_entry &= ~sgemod_mask;
+				*prp2_entry |= sgemod_val;
+			}
+		} else {
+			/*
+			 * Put entry in list and bump the addresses.
+			 *
+			 * After PRP1 and PRP2 are filled in, this will fill in
+			 * all remaining PRP entries in a PRP List, one per
+			 * each time through the loop.
+			 */
+			*prp_entry = cpu_to_le64(dma_addr);
+			if (*prp1_entry & sgemod_mask) {
+				dprint_bsg_err(mrioc,
+				    "%s: PRP address collides with SGE modifier\n",
+				    __func__);
+				goto err_out;
+			}
+			*prp_entry &= ~sgemod_mask;
+			*prp_entry |= sgemod_val;
+			prp_entry++;
+			prp_entry_dma++;
+		}
+
+		/*
+		 * Bump the phys address of the command's data buffer by the
+		 * entry_len.
+		 */
+		dma_addr += entry_len;
+
+		/* decrement length accounting for last partial page. */
+		if (entry_len > length)
+			length = 0;
+		else
+			length -= entry_len;
+	}
+	return 0;
+err_out:
+	if (mrioc->prp_list_virt) {
+		dma_free_coherent(&mrioc->pdev->dev, mrioc->prp_sz,
+		    mrioc->prp_list_virt, mrioc->prp_list_dma);
+		mrioc->prp_list_virt = NULL;
+	}
+	return -1;
+}
+/**
+ * mpi3mr_bsg_process_mpt_cmds - MPI Pass through BSG handler
+ * @job: BSG job reference
+ *
+ * This function is the top level handler for MPI Pass through
+ * command, this does basic validation of the input data buffers,
+ * identifies the given buffer types and MPI command, allocates
+ * DMAable memory for user given buffers, construstcs SGL
+ * properly and passes the command to the firmware.
+ *
+ * Once the MPI command is completed the driver copies the data
+ * if any and reply, sense information to user provided buffers.
+ * If the command is timed out then issues controller reset
+ * prior to returning.
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+
+static long mpi3mr_bsg_process_mpt_cmds(struct bsg_job *job, unsigned int *reply_payload_rcv_len)
+{
+	long rval = -EINVAL;
+
+	struct mpi3mr_ioc *mrioc = NULL;
+	u8 *mpi_req = NULL, *sense_buff_k = NULL;
+	u8 mpi_msg_size = 0;
+	struct mpi3mr_bsg_packet *bsg_req = NULL;
+	struct mpi3mr_bsg_mptcmd *karg;
+	struct mpi3mr_buf_entry *buf_entries = NULL;
+	struct mpi3mr_buf_map *drv_bufs = NULL, *drv_buf_iter = NULL;
+	u8 count, bufcnt = 0, is_rmcb = 0, is_rmrb = 0, din_cnt = 0, dout_cnt = 0;
+	u8 invalid_be = 0, erb_offset = 0xFF, mpirep_offset = 0xFF, sg_entries = 0;
+	u8 block_io = 0, resp_code = 0, nvme_fmt = 0;
+	struct mpi3_request_header *mpi_header = NULL;
+	struct mpi3_status_reply_descriptor *status_desc;
+	struct mpi3_scsi_task_mgmt_request *tm_req;
+	u32 erbsz = MPI3MR_SENSE_BUF_SZ, tmplen;
+	u16 dev_handle;
+	struct mpi3mr_tgt_dev *tgtdev;
+	struct mpi3mr_stgt_priv_data *stgt_priv = NULL;
+	struct mpi3mr_bsg_in_reply_buf *bsg_reply_buf = NULL;
+	u32 din_size = 0, dout_size = 0;
+	u8 *din_buf = NULL, *dout_buf = NULL;
+	u8 *sgl_iter = NULL, *sgl_din_iter = NULL, *sgl_dout_iter = NULL;
+
+	bsg_req = job->request;
+	karg = (struct mpi3mr_bsg_mptcmd *)&bsg_req->cmd.mptcmd;
+
+	mrioc = mpi3mr_bsg_verify_adapter(karg->mrioc_id);
+	if (!mrioc)
+		return -ENODEV;
+
+	if (karg->timeout < MPI3MR_APP_DEFAULT_TIMEOUT)
+		karg->timeout = MPI3MR_APP_DEFAULT_TIMEOUT;
+
+	mpi_req = kzalloc(MPI3MR_ADMIN_REQ_FRAME_SZ, GFP_KERNEL);
+	if (!mpi_req)
+		return -ENOMEM;
+	mpi_header = (struct mpi3_request_header *)mpi_req;
+
+	bufcnt = karg->buf_entry_list.num_of_entries;
+	drv_bufs = kzalloc((sizeof(*drv_bufs) * bufcnt), GFP_KERNEL);
+	if (!drv_bufs) {
+		rval = -ENOMEM;
+		goto out;
+	}
+
+	dout_buf = kzalloc(job->request_payload.payload_len,
+				      GFP_KERNEL);
+	if (!dout_buf) {
+		rval = -ENOMEM;
+		goto out;
+	}
+
+	din_buf = kzalloc(job->reply_payload.payload_len,
+				     GFP_KERNEL);
+	if (!din_buf) {
+		rval = -ENOMEM;
+		goto out;
+	}
+
+	sg_copy_to_buffer(job->request_payload.sg_list,
+			  job->request_payload.sg_cnt,
+			  dout_buf, job->request_payload.payload_len);
+
+	buf_entries = karg->buf_entry_list.buf_entry;
+	sgl_din_iter = din_buf;
+	sgl_dout_iter = dout_buf;
+	drv_buf_iter = drv_bufs;
+
+	for (count = 0; count < bufcnt; count++, buf_entries++, drv_buf_iter++) {
+
+		if (sgl_dout_iter > (dout_buf + job->request_payload.payload_len)) {
+			dprint_bsg_err(mrioc, "%s: data_out buffer length mismatch\n",
+				__func__);
+			rval = -EINVAL;
+			goto out;
+		}
+		if (sgl_din_iter > (din_buf + job->reply_payload.payload_len)) {
+			dprint_bsg_err(mrioc, "%s: data_in buffer length mismatch\n",
+				__func__);
+			rval = -EINVAL;
+			goto out;
+		}
+
+		switch (buf_entries->buf_type) {
+		case MPI3MR_BSG_BUFTYPE_RAIDMGMT_CMD:
+			sgl_iter = sgl_dout_iter;
+			sgl_dout_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_TO_DEVICE;
+			is_rmcb = 1;
+			if (count != 0)
+				invalid_be = 1;
+			break;
+		case MPI3MR_BSG_BUFTYPE_RAIDMGMT_RESP:
+			sgl_iter = sgl_din_iter;
+			sgl_din_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_FROM_DEVICE;
+			is_rmrb = 1;
+			if (count != 1 || !is_rmcb)
+				invalid_be = 1;
+			break;
+		case MPI3MR_BSG_BUFTYPE_DATA_IN:
+			sgl_iter = sgl_din_iter;
+			sgl_din_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_FROM_DEVICE;
+			din_cnt++;
+			din_size += drv_buf_iter->bsg_buf_len;
+			if ((din_cnt > 1) && !is_rmcb)
+				invalid_be = 1;
+			break;
+		case MPI3MR_BSG_BUFTYPE_DATA_OUT:
+			sgl_iter = sgl_dout_iter;
+			sgl_dout_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_TO_DEVICE;
+			dout_cnt++;
+			dout_size += drv_buf_iter->bsg_buf_len;
+			if ((dout_cnt > 1) && !is_rmcb)
+				invalid_be = 1;
+			break;
+		case MPI3MR_BSG_BUFTYPE_MPI_REPLY:
+			sgl_iter = sgl_din_iter;
+			sgl_din_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_NONE;
+			mpirep_offset = count;
+			break;
+		case MPI3MR_BSG_BUFTYPE_ERR_RESPONSE:
+			sgl_iter = sgl_din_iter;
+			sgl_din_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_NONE;
+			erb_offset = count;
+			break;
+		case MPI3MR_BSG_BUFTYPE_MPI_REQUEST:
+			sgl_iter = sgl_dout_iter;
+			sgl_dout_iter += buf_entries->buf_len;
+			drv_buf_iter->data_dir = DMA_NONE;
+			mpi_msg_size = buf_entries->buf_len;
+			if ((!mpi_msg_size || (mpi_msg_size % 4)) ||
+					(mpi_msg_size > MPI3MR_ADMIN_REQ_FRAME_SZ)) {
+				dprint_bsg_err(mrioc, "%s: invalid MPI message size\n",
+					__func__);
+				rval = -EINVAL;
+				goto out;
+			}
+			memcpy(mpi_req, sgl_iter, buf_entries->buf_len);
+			break;
+		default:
+			invalid_be = 1;
+			break;
+		}
+		if (invalid_be) {
+			dprint_bsg_err(mrioc, "%s: invalid buffer entries passed\n",
+				__func__);
+			rval = -EINVAL;
+			goto out;
+		}
+
+		drv_buf_iter->bsg_buf = sgl_iter;
+		drv_buf_iter->bsg_buf_len = buf_entries->buf_len;
+
+	}
+	if (!is_rmcb && (dout_cnt || din_cnt)) {
+		sg_entries = dout_cnt + din_cnt;
+		if (((mpi_msg_size) + (sg_entries *
+		      sizeof(struct mpi3_sge_common))) > MPI3MR_ADMIN_REQ_FRAME_SZ) {
+			dprint_bsg_err(mrioc,
+			    "%s:%d: invalid message size passed\n",
+			    __func__, __LINE__);
+			rval = -EINVAL;
+			goto out;
+		}
+	}
+	if (din_size > MPI3MR_MAX_APP_XFER_SIZE) {
+		dprint_bsg_err(mrioc,
+		    "%s:%d: invalid data transfer size passed for function 0x%x din_size=%d\n",
+		    __func__, __LINE__, mpi_header->function, din_size);
+		rval = -EINVAL;
+		goto out;
+	}
+	if (dout_size > MPI3MR_MAX_APP_XFER_SIZE) {
+		dprint_bsg_err(mrioc,
+		    "%s:%d: invalid data transfer size passed for function 0x%x dout_size = %d\n",
+		    __func__, __LINE__, mpi_header->function, dout_size);
+		rval = -EINVAL;
+		goto out;
+	}
+
+	drv_buf_iter = drv_bufs;
+	for (count = 0; count < bufcnt; count++, drv_buf_iter++) {
+		if (drv_buf_iter->data_dir == DMA_NONE)
+			continue;
+
+		drv_buf_iter->kern_buf_len = drv_buf_iter->bsg_buf_len;
+		if (is_rmcb && !count)
+			drv_buf_iter->kern_buf_len += ((dout_cnt + din_cnt) *
+			    sizeof(struct mpi3_sge_common));
+
+		if (!drv_buf_iter->kern_buf_len)
+			continue;
+
+		drv_buf_iter->kern_buf = dma_alloc_coherent(&mrioc->pdev->dev,
+		    drv_buf_iter->kern_buf_len, &drv_buf_iter->kern_buf_dma,
+		    GFP_KERNEL);
+		if (!drv_buf_iter->kern_buf) {
+			rval = -ENOMEM;
+			goto out;
+		}
+		if (drv_buf_iter->data_dir == DMA_TO_DEVICE) {
+			tmplen = min(drv_buf_iter->kern_buf_len,
+			    drv_buf_iter->bsg_buf_len);
+			memcpy(drv_buf_iter->kern_buf, drv_buf_iter->bsg_buf, tmplen);
+		}
+	}
+
+	if (erb_offset != 0xFF) {
+		sense_buff_k = kzalloc(erbsz, GFP_KERNEL);
+		if (!sense_buff_k) {
+			rval = -ENOMEM;
+			goto out;
+		}
+	}
+
+	if (mutex_lock_interruptible(&mrioc->bsg_cmds.mutex)) {
+		rval = -ERESTARTSYS;
+		goto out;
+	}
+	if (mrioc->bsg_cmds.state & MPI3MR_CMD_PENDING) {
+		rval = -EAGAIN;
+		dprint_bsg_err(mrioc, "%s: command is in use\n", __func__);
+		mutex_unlock(&mrioc->bsg_cmds.mutex);
+		goto out;
+	}
+	if (mrioc->unrecoverable) {
+		dprint_bsg_err(mrioc, "%s: unrecoverable controller\n",
+		    __func__);
+		rval = -EFAULT;
+		mutex_unlock(&mrioc->bsg_cmds.mutex);
+		goto out;
+	}
+	if (mrioc->reset_in_progress) {
+		dprint_bsg_err(mrioc, "%s: reset in progress\n", __func__);
+		rval = -EAGAIN;
+		mutex_unlock(&mrioc->bsg_cmds.mutex);
+		goto out;
+	}
+	if (mrioc->stop_bsgs) {
+		dprint_bsg_err(mrioc, "%s: bsgs are blocked\n", __func__);
+		rval = -EAGAIN;
+		mutex_unlock(&mrioc->bsg_cmds.mutex);
+		goto out;
+	}
+
+	if (mpi_header->function == MPI3_BSG_FUNCTION_NVME_ENCAPSULATED) {
+		nvme_fmt = mpi3mr_get_nvme_data_fmt(
+			(struct mpi3_nvme_encapsulated_request *)mpi_req);
+		if (nvme_fmt == MPI3MR_NVME_DATA_FORMAT_PRP) {
+			if (mpi3mr_build_nvme_prp(mrioc,
+			    (struct mpi3_nvme_encapsulated_request *)mpi_req,
+			    drv_bufs, bufcnt)) {
+				rval = -ENOMEM;
+				mutex_unlock(&mrioc->bsg_cmds.mutex);
+				goto out;
+			}
+		} else if (nvme_fmt == MPI3MR_NVME_DATA_FORMAT_SGL1 ||
+			nvme_fmt == MPI3MR_NVME_DATA_FORMAT_SGL2) {
+			if (mpi3mr_build_nvme_sgl(mrioc,
+			    (struct mpi3_nvme_encapsulated_request *)mpi_req,
+			    drv_bufs, bufcnt)) {
+				rval = -EINVAL;
+				mutex_unlock(&mrioc->bsg_cmds.mutex);
+				goto out;
+			}
+		} else {
+			dprint_bsg_err(mrioc,
+			    "%s:invalid NVMe command format\n", __func__);
+			rval = -EINVAL;
+			mutex_unlock(&mrioc->bsg_cmds.mutex);
+			goto out;
+		}
+	} else {
+		mpi3mr_bsg_build_sgl(mpi_req, (mpi_msg_size),
+		    drv_bufs, bufcnt, is_rmcb, is_rmrb,
+		    (dout_cnt + din_cnt));
+	}
+
+	if (mpi_header->function == MPI3_BSG_FUNCTION_SCSI_TASK_MGMT) {
+		tm_req = (struct mpi3_scsi_task_mgmt_request *)mpi_req;
+		if (tm_req->task_type !=
+		    MPI3_SCSITASKMGMT_TASKTYPE_ABORT_TASK) {
+			dev_handle = tm_req->dev_handle;
+			block_io = 1;
+		}
+	}
+	if (block_io) {
+		tgtdev = mpi3mr_get_tgtdev_by_handle(mrioc, dev_handle);
+		if (tgtdev && tgtdev->starget && tgtdev->starget->hostdata) {
+			stgt_priv = (struct mpi3mr_stgt_priv_data *)
+			    tgtdev->starget->hostdata;
+			atomic_inc(&stgt_priv->block_io);
+			mpi3mr_tgtdev_put(tgtdev);
+		}
+	}
+
+	mrioc->bsg_cmds.state = MPI3MR_CMD_PENDING;
+	mrioc->bsg_cmds.is_waiting = 1;
+	mrioc->bsg_cmds.callback = NULL;
+	mrioc->bsg_cmds.is_sense = 0;
+	mrioc->bsg_cmds.sensebuf = sense_buff_k;
+	memset(mrioc->bsg_cmds.reply, 0, mrioc->reply_sz);
+	mpi_header->host_tag = cpu_to_le16(MPI3MR_HOSTTAG_BSG_CMDS);
+	if (mrioc->logging_level & MPI3_DEBUG_BSG_INFO) {
+		dprint_bsg_info(mrioc,
+		    "%s: posting bsg request to the controller\n", __func__);
+		dprint_dump(mpi_req, MPI3MR_ADMIN_REQ_FRAME_SZ,
+		    "bsg_mpi3_req");
+		if (mpi_header->function == MPI3_BSG_FUNCTION_MGMT_PASSTHROUGH) {
+			drv_buf_iter = &drv_bufs[0];
+			dprint_dump(drv_buf_iter->kern_buf,
+			    drv_buf_iter->kern_buf_len, "mpi3_mgmt_req");
+		}
+	}
+
+	init_completion(&mrioc->bsg_cmds.done);
+	rval = mpi3mr_admin_request_post(mrioc, mpi_req,
+	    MPI3MR_ADMIN_REQ_FRAME_SZ, 0);
+
+
+	if (rval) {
+		mrioc->bsg_cmds.is_waiting = 0;
+		dprint_bsg_err(mrioc,
+		    "%s: posting bsg request is failed\n", __func__);
+		rval = -EAGAIN;
+		goto out_unlock;
+	}
+	wait_for_completion_timeout(&mrioc->bsg_cmds.done,
+	    (karg->timeout * HZ));
+	if (block_io && stgt_priv)
+		atomic_dec(&stgt_priv->block_io);
+	if (!(mrioc->bsg_cmds.state & MPI3MR_CMD_COMPLETE)) {
+		mrioc->bsg_cmds.is_waiting = 0;
+		rval = -EAGAIN;
+		if (mrioc->bsg_cmds.state & MPI3MR_CMD_RESET)
+			goto out_unlock;
+		dprint_bsg_err(mrioc,
+		    "%s: bsg request timedout after %d seconds\n", __func__,
+		    karg->timeout);
+		if (mrioc->logging_level & MPI3_DEBUG_BSG_ERROR) {
+			dprint_dump(mpi_req, MPI3MR_ADMIN_REQ_FRAME_SZ,
+			    "bsg_mpi3_req");
+			if (mpi_header->function ==
+			    MPI3_BSG_FUNCTION_MGMT_PASSTHROUGH) {
+				drv_buf_iter = &drv_bufs[0];
+				dprint_dump(drv_buf_iter->kern_buf,
+				    drv_buf_iter->kern_buf_len, "mpi3_mgmt_req");
+			}
+		}
+
+		if ((mpi_header->function == MPI3_BSG_FUNCTION_NVME_ENCAPSULATED) ||
+		    (mpi_header->function == MPI3_BSG_FUNCTION_SCSI_IO))
+			mpi3mr_issue_tm(mrioc,
+			    MPI3_SCSITASKMGMT_TASKTYPE_TARGET_RESET,
+			    mpi_header->function_dependent, 0,
+			    MPI3MR_HOSTTAG_BLK_TMS, MPI3MR_RESETTM_TIMEOUT,
+			    &mrioc->host_tm_cmds, &resp_code, NULL);
+		if (!(mrioc->bsg_cmds.state & MPI3MR_CMD_COMPLETE) &&
+		    !(mrioc->bsg_cmds.state & MPI3MR_CMD_RESET))
+			mpi3mr_soft_reset_handler(mrioc,
+			    MPI3MR_RESET_FROM_APP_TIMEOUT, 1);
+		goto out_unlock;
+	}
+	dprint_bsg_info(mrioc, "%s: bsg request is completed\n", __func__);
+
+	if (mrioc->prp_list_virt) {
+		dma_free_coherent(&mrioc->pdev->dev, mrioc->prp_sz,
+		    mrioc->prp_list_virt, mrioc->prp_list_dma);
+		mrioc->prp_list_virt = NULL;
+	}
+
+	if ((mrioc->bsg_cmds.ioc_status & MPI3_IOCSTATUS_STATUS_MASK)
+	     != MPI3_IOCSTATUS_SUCCESS) {
+		dprint_bsg_info(mrioc,
+		    "%s: command failed, ioc_status(0x%04x) log_info(0x%08x)\n",
+		    __func__,
+		    (mrioc->bsg_cmds.ioc_status & MPI3_IOCSTATUS_STATUS_MASK),
+		    mrioc->bsg_cmds.ioc_loginfo);
+	}
+
+	if ((mpirep_offset != 0xFF) &&
+	    drv_bufs[mpirep_offset].bsg_buf_len) {
+		drv_buf_iter = &drv_bufs[mpirep_offset];
+		drv_buf_iter->kern_buf_len = (sizeof(*bsg_reply_buf) - 1 +
+					   mrioc->reply_sz);
+		bsg_reply_buf = kzalloc(drv_buf_iter->kern_buf_len, GFP_KERNEL);
+
+		if (!bsg_reply_buf) {
+			rval = -ENOMEM;
+			goto out_unlock;
+		}
+		if (mrioc->bsg_cmds.state & MPI3MR_CMD_REPLY_VALID) {
+			bsg_reply_buf->mpi_reply_type =
+				MPI3MR_BSG_MPI_REPLY_BUFTYPE_ADDRESS;
+			memcpy(bsg_reply_buf->reply_buf,
+			    mrioc->bsg_cmds.reply, mrioc->reply_sz);
+		} else {
+			bsg_reply_buf->mpi_reply_type =
+				MPI3MR_BSG_MPI_REPLY_BUFTYPE_STATUS;
+			status_desc = (struct mpi3_status_reply_descriptor *)
+			    bsg_reply_buf->reply_buf;
+			status_desc->ioc_status = mrioc->bsg_cmds.ioc_status;
+			status_desc->ioc_log_info = mrioc->bsg_cmds.ioc_loginfo;
+		}
+		tmplen = min(drv_buf_iter->kern_buf_len,
+			drv_buf_iter->bsg_buf_len);
+		memcpy(drv_buf_iter->bsg_buf, bsg_reply_buf, tmplen);
+	}
+
+	if (erb_offset != 0xFF && mrioc->bsg_cmds.sensebuf &&
+	    mrioc->bsg_cmds.is_sense) {
+		drv_buf_iter = &drv_bufs[erb_offset];
+		tmplen = min(erbsz, drv_buf_iter->bsg_buf_len);
+		memcpy(drv_buf_iter->bsg_buf, sense_buff_k, tmplen);
+	}
+
+	drv_buf_iter = drv_bufs;
+	for (count = 0; count < bufcnt; count++, drv_buf_iter++) {
+		if (drv_buf_iter->data_dir == DMA_NONE)
+			continue;
+		if (drv_buf_iter->data_dir == DMA_FROM_DEVICE) {
+			tmplen = min(drv_buf_iter->kern_buf_len,
+				     drv_buf_iter->bsg_buf_len);
+			memcpy(drv_buf_iter->bsg_buf,
+			       drv_buf_iter->kern_buf, tmplen);
+		}
+	}
+
+out_unlock:
+	if (din_buf) {
+		*reply_payload_rcv_len =
+			sg_copy_from_buffer(job->reply_payload.sg_list,
+					    job->reply_payload.sg_cnt,
+					    din_buf, job->reply_payload.payload_len);
+	}
+	mrioc->bsg_cmds.is_sense = 0;
+	mrioc->bsg_cmds.sensebuf = NULL;
+	mrioc->bsg_cmds.state = MPI3MR_CMD_NOTUSED;
+	mutex_unlock(&mrioc->bsg_cmds.mutex);
+out:
+	kfree(sense_buff_k);
+	kfree(dout_buf);
+	kfree(din_buf);
+	kfree(mpi_req);
+	if (drv_bufs) {
+		drv_buf_iter = drv_bufs;
+		for (count = 0; count < bufcnt; count++, drv_buf_iter++) {
+			if (drv_buf_iter->kern_buf && drv_buf_iter->kern_buf_dma)
+				dma_free_coherent(&mrioc->pdev->dev,
+				    drv_buf_iter->kern_buf_len,
+				    drv_buf_iter->kern_buf,
+				    drv_buf_iter->kern_buf_dma);
+		}
+		kfree(drv_bufs);
+	}
+	kfree(bsg_reply_buf);
+	return rval;
+}
+
+/**
+ * mpi3mr_app_save_logdata - Save Log Data events
+ * @mrioc: Adapter instance reference
+ * @event_data: event data associated with log data event
+ * @event_data_size: event data size to copy
+ *
+ * If log data event caching is enabled by the applicatiobns,
+ * then this function saves the log data in the circular queue
+ * and Sends async signal SIGIO to indicate there is an async
+ * event from the firmware to the event monitoring applications.
+ *
+ * Return:Nothing
+ */
+void mpi3mr_app_save_logdata(struct mpi3mr_ioc *mrioc, char *event_data,
+	u16 event_data_size)
+{
+	u32 index = mrioc->logdata_buf_idx, sz;
+	struct mpi3mr_logdata_entry *entry;
+
+	if (!(mrioc->logdata_buf))
+		return;
+
+	entry = (struct mpi3mr_logdata_entry *)
+		(mrioc->logdata_buf + (index * mrioc->logdata_entry_sz));
+	entry->valid_entry = 1;
+	sz = min(mrioc->logdata_entry_sz, event_data_size);
+	memcpy(entry->data, event_data, sz);
+	mrioc->logdata_buf_idx =
+		((++index) % MPI3MR_BSG_LOGDATA_MAX_ENTRIES);
+	atomic64_inc(&event_counter);
+}
+
+/**
+ * mpi3mr_bsg_request - bsg request entry point
+ * @job: BSG job reference
+ *
+ * This is driver's entry point for bsg requests
+ *
+ * Return: 0 on success and proper error codes on failure
+ */
+static int mpi3mr_bsg_request(struct bsg_job *job)
+{
+	long rval = -EINVAL;
+	unsigned int reply_payload_rcv_len = 0;
+
+	struct mpi3mr_bsg_packet *bsg_req = job->request;
+
+	switch (bsg_req->cmd_type) {
+	case MPI3MR_DRV_CMD:
+		rval = mpi3mr_bsg_process_drv_cmds(job);
+		break;
+	case MPI3MR_MPT_CMD:
+		rval = mpi3mr_bsg_process_mpt_cmds(job, &reply_payload_rcv_len);
+		break;
+	default:
+		pr_err("%s: unsupported BSG command(0x%08x)\n",
+		    MPI3MR_DRIVER_NAME, bsg_req->cmd_type);
+		break;
+	}
+
+	bsg_job_done(job, rval, reply_payload_rcv_len);
+
+	return 0;
+}
+
+/**
+ * mpi3mr_bsg_exit - de-registration from bsg layer
+ *
+ * This will be called during driver unload and all
+ * bsg resources allocated during load will be freed.
+ *
+ * Return:Nothing
+ */
+void mpi3mr_bsg_exit(struct mpi3mr_ioc *mrioc)
+{
+	struct device *bsg_dev = &mrioc->bsg_dev;
+	if (!mrioc->bsg_queue)
+		return;
+
+	bsg_remove_queue(mrioc->bsg_queue);
+	mrioc->bsg_queue = NULL;
+
+	device_del(bsg_dev);
+	put_device(bsg_dev);
+}
+
+/**
+ * mpi3mr_bsg_node_release -release bsg device node
+ * @dev: bsg device node
+ *
+ * decrements bsg dev parent reference count
+ *
+ * Return:Nothing
+ */
+static void mpi3mr_bsg_node_release(struct device *dev)
+{
+	put_device(dev->parent);
+}
+
+/**
+ * mpi3mr_bsg_init -  registration with bsg layer
+ *
+ * This will be called during driver load and it will
+ * register driver with bsg layer
+ *
+ * Return:Nothing
+ */
+void mpi3mr_bsg_init(struct mpi3mr_ioc *mrioc)
+{
+	struct device *bsg_dev = &mrioc->bsg_dev;
+	struct device *parent = &mrioc->shost->shost_gendev;
+
+	device_initialize(bsg_dev);
+
+	bsg_dev->parent = get_device(parent);
+	bsg_dev->release = mpi3mr_bsg_node_release;
+
+	dev_set_name(bsg_dev, "mpi3mrctl%u", mrioc->id);
+
+	if (device_add(bsg_dev)) {
+		ioc_err(mrioc, "%s: bsg device add failed\n",
+		    dev_name(bsg_dev));
+		put_device(bsg_dev);
+		return;
+	}
+
+	mrioc->bsg_queue = bsg_setup_queue(bsg_dev, dev_name(bsg_dev),
+			mpi3mr_bsg_request, NULL, 0);
+	if (IS_ERR(mrioc->bsg_queue)) {
+		ioc_err(mrioc, "%s: bsg registration failed\n",
+		    dev_name(bsg_dev));
+		device_del(bsg_dev);
+		put_device(bsg_dev);
+		return;
+	}
+
+	blk_queue_max_segments(mrioc->bsg_queue, MPI3MR_MAX_APP_XFER_SEGMENTS);
+	blk_queue_max_hw_sectors(mrioc->bsg_queue, MPI3MR_MAX_APP_XFER_SECTORS);
+
+	return;
+}
+
+/**
+ * version_fw_show - SysFS callback for firmware version read
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying firmware version
+ */
+static ssize_t
+version_fw_show(struct device *dev, struct device_attribute *attr,
+	char *buf)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+	struct mpi3mr_compimg_ver *fwver = &mrioc->facts.fw_ver;
+
+	return sysfs_emit(buf, "%d.%d.%d.%d.%05d-%05d\n",
+	    fwver->gen_major, fwver->gen_minor, fwver->ph_major,
+	    fwver->ph_minor, fwver->cust_id, fwver->build_num);
+}
+static DEVICE_ATTR_RO(version_fw);
+
+/**
+ * fw_queue_depth_show - SysFS callback for firmware max cmds
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying firmware max commands
+ */
+static ssize_t
+fw_queue_depth_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+
+	return sysfs_emit(buf, "%d\n", mrioc->facts.max_reqs);
+}
+static DEVICE_ATTR_RO(fw_queue_depth);
+
+/**
+ * op_req_q_count_show - SysFS callback for request queue count
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying request queue count
+ */
+static ssize_t
+op_req_q_count_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+
+	return sysfs_emit(buf, "%d\n", mrioc->num_op_req_q);
+}
+static DEVICE_ATTR_RO(op_req_q_count);
+
+/**
+ * reply_queue_count_show - SysFS callback for reply queue count
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying reply queue count
+ */
+static ssize_t
+reply_queue_count_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+
+	return sysfs_emit(buf, "%d\n", mrioc->num_op_reply_q);
+}
+
+static DEVICE_ATTR_RO(reply_queue_count);
+
+/**
+ * logging_level_show - Show controller debug level
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * A sysfs 'read/write' shost attribute, to show the current
+ * debug log level used by the driver for the specific
+ * controller.
+ *
+ * Return: sysfs_emit() return
+ */
+static ssize_t
+logging_level_show(struct device *dev,
+	struct device_attribute *attr, char *buf)
+
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+
+	return sysfs_emit(buf, "%08xh\n", mrioc->logging_level);
+}
+
+/**
+ * logging_level_store- Change controller debug level
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ * @count: size of the buffer
+ *
+ * A sysfs 'read/write' shost attribute, to change the current
+ * debug log level used by the driver for the specific
+ * controller.
+ *
+ * Return: strlen() return
+ */
+static ssize_t
+logging_level_store(struct device *dev,
+	struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+	int val = 0;
+
+	if (kstrtoint(buf, 0, &val) != 0)
+		return -EINVAL;
+
+	mrioc->logging_level = val;
+	ioc_info(mrioc, "logging_level=%08xh\n", mrioc->logging_level);
+	return strlen(buf);
+}
+static DEVICE_ATTR_RW(logging_level);
+
+/**
+ * adp_state_show() - SysFS callback for adapter state show
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying adapter state
+ */
+static ssize_t
+adp_state_show(struct device *dev, struct device_attribute *attr,
+	char *buf)
+{
+	struct Scsi_Host *shost = class_to_shost(dev);
+	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+	enum mpi3mr_iocstate ioc_state;
+	uint8_t adp_state;
+
+	ioc_state = mpi3mr_get_iocstate(mrioc);
+	if (ioc_state == MRIOC_STATE_UNRECOVERABLE)
+		adp_state = MPI3MR_BSG_ADPSTATE_UNRECOVERABLE;
+	else if ((mrioc->reset_in_progress) || (mrioc->stop_bsgs))
+		adp_state = MPI3MR_BSG_ADPSTATE_IN_RESET;
+	else if (ioc_state == MRIOC_STATE_FAULT)
+		adp_state = MPI3MR_BSG_ADPSTATE_FAULT;
+	else
+		adp_state = MPI3MR_BSG_ADPSTATE_OPERATIONAL;
+
+	return sysfs_emit(buf, "%u\n", adp_state);
+}
+
+static DEVICE_ATTR_RO(adp_state);
+
+static struct attribute *mpi3mr_host_attrs[] = {
+	&dev_attr_version_fw.attr,
+	&dev_attr_fw_queue_depth.attr,
+	&dev_attr_op_req_q_count.attr,
+	&dev_attr_reply_queue_count.attr,
+	&dev_attr_logging_level.attr,
+	&dev_attr_adp_state.attr,
+	NULL,
+};
+
+static const struct attribute_group mpi3mr_host_attr_group = {
+	.attrs = mpi3mr_host_attrs
+};
+
+const struct attribute_group *mpi3mr_host_groups[] = {
+	&mpi3mr_host_attr_group,
+	NULL,
+};
+
+
+/*
+ * SCSI Device attributes under sysfs
+ */
+
+/**
+ * sas_address_show - SysFS callback for dev SASaddress display
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying SAS address of the
+ * specific SAS/SATA end device.
+ */
+static ssize_t
+sas_address_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	struct mpi3mr_sdev_priv_data *sdev_priv_data;
+	struct mpi3mr_stgt_priv_data *tgt_priv_data;
+	struct mpi3mr_tgt_dev *tgtdev;
+
+	sdev_priv_data = sdev->hostdata;
+	if (!sdev_priv_data)
+		return 0;
+
+	tgt_priv_data = sdev_priv_data->tgt_priv_data;
+	if (!tgt_priv_data)
+		return 0;
+	tgtdev = tgt_priv_data->tgt_dev;
+	if (!tgtdev || tgtdev->dev_type != MPI3_DEVICE_DEVFORM_SAS_SATA)
+		return 0;
+	return sysfs_emit(buf, "0x%016llx\n",
+	    (unsigned long long)tgtdev->dev_spec.sas_sata_inf.sas_address);
+}
+
+static DEVICE_ATTR_RO(sas_address);
+
+/**
+ * device_handle_show - SysFS callback for device handle display
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying firmware internal
+ * device handle of the specific device.
+ */
+static ssize_t
+device_handle_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	struct mpi3mr_sdev_priv_data *sdev_priv_data;
+	struct mpi3mr_stgt_priv_data *tgt_priv_data;
+	struct mpi3mr_tgt_dev *tgtdev;
+
+	sdev_priv_data = sdev->hostdata;
+	if (!sdev_priv_data)
+		return 0;
+
+	tgt_priv_data = sdev_priv_data->tgt_priv_data;
+	if (!tgt_priv_data)
+		return 0;
+	tgtdev = tgt_priv_data->tgt_dev;
+	if (!tgtdev)
+		return 0;
+	return sysfs_emit(buf, "0x%04x\n", tgtdev->dev_handle);
+}
+
+static DEVICE_ATTR_RO(device_handle);
+
+/**
+ * persistent_id_show - SysFS callback for persisten ID display
+ * @dev: class device
+ * @attr: Device attributes
+ * @buf: Buffer to copy
+ *
+ * Return: sysfs_emit() return after copying persistent ID of the
+ * of the specific device.
+ */
+static ssize_t
+persistent_id_show(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	struct mpi3mr_sdev_priv_data *sdev_priv_data;
+	struct mpi3mr_stgt_priv_data *tgt_priv_data;
+	struct mpi3mr_tgt_dev *tgtdev;
+
+	sdev_priv_data = sdev->hostdata;
+	if (!sdev_priv_data)
+		return 0;
+
+	tgt_priv_data = sdev_priv_data->tgt_priv_data;
+	if (!tgt_priv_data)
+		return 0;
+	tgtdev = tgt_priv_data->tgt_dev;
+	if (!tgtdev)
+		return 0;
+	return sysfs_emit(buf, "%d\n", tgtdev->perst_id);
+}
+static DEVICE_ATTR_RO(persistent_id);
+
+static struct attribute *mpi3mr_dev_attrs[] = {
+	&dev_attr_sas_address.attr,
+	&dev_attr_device_handle.attr,
+	&dev_attr_persistent_id.attr,
+	NULL,
+};
+
+static const struct attribute_group mpi3mr_dev_attr_group = {
+	.attrs = mpi3mr_dev_attrs
+};
+
+const struct attribute_group *mpi3mr_dev_groups[] = {
+	&mpi3mr_dev_attr_group,
+	NULL,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi3mr_debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi3mr_debug.h
@@ -2,7 +2,7 @@
 /*
  * Driver for Broadcom MPI3 Storage Controllers
  *
- * Copyright (C) 2017-2021 Broadcom Inc.
+ * Copyright (C) 2017-2022 Broadcom Inc.
  *  (mailto: mpi3mr-linuxdrv.pdl@broadcom.com)
  *
  */
@@ -14,27 +14,20 @@
 /*
  * debug levels
  */
-#define MPI3_DEBUG			0x00000001
-#define MPI3_DEBUG_MSG_FRAME		0x00000002
-#define MPI3_DEBUG_SG			0x00000004
-#define MPI3_DEBUG_EVENTS		0x00000008
-#define MPI3_DEBUG_EVENT_WORK_TASK	0x00000010
-#define MPI3_DEBUG_INIT			0x00000020
-#define MPI3_DEBUG_EXIT			0x00000040
-#define MPI3_DEBUG_FAIL			0x00000080
-#define MPI3_DEBUG_TM			0x00000100
-#define MPI3_DEBUG_REPLY		0x00000200
-#define MPI3_DEBUG_HANDSHAKE		0x00000400
-#define MPI3_DEBUG_CONFIG		0x00000800
-#define MPI3_DEBUG_DL			0x00001000
-#define MPI3_DEBUG_RESET		0x00002000
-#define MPI3_DEBUG_SCSI			0x00004000
-#define MPI3_DEBUG_IOCTL		0x00008000
-#define MPI3_DEBUG_CSMISAS		0x00010000
-#define MPI3_DEBUG_SAS			0x00020000
-#define MPI3_DEBUG_TRANSPORT		0x00040000
-#define MPI3_DEBUG_TASK_SET_FULL	0x00080000
-#define MPI3_DEBUG_TRIGGER_DIAG		0x00200000
+
+#define MPI3_DEBUG_EVENT		0x00000001
+#define MPI3_DEBUG_EVENT_WORK_TASK	0x00000002
+#define MPI3_DEBUG_INIT		0x00000004
+#define MPI3_DEBUG_EXIT		0x00000008
+#define MPI3_DEBUG_TM			0x00000010
+#define MPI3_DEBUG_RESET		0x00000020
+#define MPI3_DEBUG_SCSI_ERROR		0x00000040
+#define MPI3_DEBUG_REPLY		0x00000080
+#define MPI3_DEBUG_BSG_ERROR		0x00008000
+#define MPI3_DEBUG_BSG_INFO		0x00010000
+#define MPI3_DEBUG_SCSI_INFO		0x00020000
+#define MPI3_DEBUG			0x01000000
+#define MPI3_DEBUG_SG			0x02000000
 
 
 /*
@@ -50,11 +43,128 @@
 #define ioc_info(ioc, fmt, ...) \
 	pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__)
 
+#define dprint(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_event_th(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_EVENT) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_event_bh(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_EVENT_WORK_TASK) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_init(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_INIT) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_exit(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_EXIT) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_tm(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_TM) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_reply(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_REPLY) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_reset(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_RESET) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_scsi_info(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_SCSI_INFO) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_scsi_err(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_SCSI_ERROR) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
+
+#define dprint_scsi_command(ioc, SCMD, LOG_LEVEL) \
+	do { \
+		if (ioc->logging_level & LOG_LEVEL) \
+			scsi_print_command(SCMD); \
+	} while (0)
+
+
+#define dprint_bsg_info(ioc, fmt, ...) \
+	do { \
+		if (ioc->logging_level & MPI3_DEBUG_BSG_INFO) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
+	} while (0)
 
-#define dbgprint(IOC, FMT, ...) \
+#define dprint_bsg_err(ioc, fmt, ...) \
 	do { \
-		if (IOC->logging_level & MPI3_DEBUG) \
-			pr_info("%s: " FMT, (IOC)->name, ##__VA_ARGS__); \
+		if (ioc->logging_level & MPI3_DEBUG_BSG_ERROR) \
+			pr_info("%s: " fmt, (ioc)->name, ##__VA_ARGS__); \
 	} while (0)
 
 #endif /* MPT3SAS_DEBUG_H_INCLUDED */
+
+/**
+ * dprint_dump - print contents of a memory buffer
+ * @req: Pointer to a memory buffer
+ * @sz: Memory buffer size
+ * @namestr: Name String to identify the buffer type
+ */
+static inline void
+dprint_dump(void *req, int sz, const char *name_string)
+{
+	int i;
+	__le32 *mfp = (__le32 *)req;
+
+	sz = sz/4;
+	if (name_string)
+		pr_info("%s:\n\t", name_string);
+	else
+		pr_info("request:\n\t");
+	for (i = 0; i < sz; i++) {
+		if (i && ((i % 8) == 0))
+			pr_info("\n\t");
+		pr_info("%08x ", le32_to_cpu(mfp[i]));
+	}
+	pr_info("\n");
+}
+
+/**
+ * dprint_dump_req - print message frame contents
+ * @req: pointer to message frame
+ * @sz: number of dwords
+ */
+static inline void
+dprint_dump_req(void *req, int sz)
+{
+	int i;
+	__le32 *mfp = (__le32 *)req;
+
+	pr_info("request:\n\t");
+	for (i = 0; i < sz; i++) {
+		if (i && ((i % 8) == 0))
+			pr_info("\n\t");
+		pr_info("%08x ", le32_to_cpu(mfp[i]));
+	}
+	pr_info("\n");
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi3mr_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi3mr_fw.c
@@ -2,7 +2,7 @@
 /*
  * Driver for Broadcom MPI3 Storage Controllers
  *
- * Copyright (C) 2017-2021 Broadcom Inc.
+ * Copyright (C) 2017-2022 Broadcom Inc.
  *  (mailto: mpi3mr-linuxdrv.pdl@broadcom.com)
  *
  */
@@ -10,6 +10,18 @@
 #include "mpi3mr.h"
 #include <linux/io-64-nonatomic-lo-hi.h>
 
+static int
+mpi3mr_issue_reset(struct mpi3mr_ioc *mrioc, u16 reset_type, u32 reset_reason);
+static int mpi3mr_setup_admin_qpair(struct mpi3mr_ioc *mrioc);
+static void mpi3mr_process_factsdata(struct mpi3mr_ioc *mrioc,
+	struct mpi3_ioc_facts_data *facts_data);
+static void mpi3mr_pel_wait_complete(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd);
+
+static int poll_queues;
+module_param(poll_queues, int, 0444);
+MODULE_PARM_DESC(poll_queues, "Number of queues for io_uring poll mode. (Range 1 - 126)");
+
 #if defined(writeq) && defined(CONFIG_64BIT)
 static inline void mpi3mr_writeq(__u64 b, volatile void __iomem *addr)
 {
@@ -78,6 +90,7 @@
 	kfree(mrioc->intr_info);
 	mrioc->intr_info = NULL;
 	mrioc->intr_info_count = 0;
+	mrioc->is_intr_info_set = false;
 	pci_free_irq_vectors(mrioc->pdev);
 }
 
@@ -124,8 +137,9 @@
 	u64 reply_dma)
 {
 	u32 old_idx = 0;
+	unsigned long flags;
 
-	spin_lock(&mrioc->reply_free_queue_lock);
+	spin_lock_irqsave(&mrioc->reply_free_queue_lock, flags);
 	old_idx  =  mrioc->reply_free_queue_host_index;
 	mrioc->reply_free_queue_host_index = (
 	    (mrioc->reply_free_queue_host_index ==
@@ -134,15 +148,16 @@
 	mrioc->reply_free_q[old_idx] = cpu_to_le64(reply_dma);
 	writel(mrioc->reply_free_queue_host_index,
 	    &mrioc->sysif_regs->reply_free_host_index);
-	spin_unlock(&mrioc->reply_free_queue_lock);
+	spin_unlock_irqrestore(&mrioc->reply_free_queue_lock, flags);
 }
 
 void mpi3mr_repost_sense_buf(struct mpi3mr_ioc *mrioc,
 	u64 sense_buf_dma)
 {
 	u32 old_idx = 0;
+	unsigned long flags;
 
-	spin_lock(&mrioc->sbq_lock);
+	spin_lock_irqsave(&mrioc->sbq_lock, flags);
 	old_idx  =  mrioc->sbq_host_index;
 	mrioc->sbq_host_index = ((mrioc->sbq_host_index ==
 	    (mrioc->sense_buf_q_sz - 1)) ? 0 :
@@ -150,7 +165,7 @@
 	mrioc->sense_buf_q[old_idx] = cpu_to_le64(sense_buf_dma);
 	writel(mrioc->sbq_host_index,
 	    &mrioc->sysif_regs->sense_buffer_free_host_index);
-	spin_unlock(&mrioc->sbq_lock);
+	spin_unlock_irqrestore(&mrioc->sbq_lock, flags);
 }
 
 static void mpi3mr_print_event_data(struct mpi3mr_ioc *mrioc,
@@ -171,9 +186,6 @@
 	case MPI3_EVENT_GPIO_INTERRUPT:
 		desc = "GPIO Interrupt";
 		break;
-	case MPI3_EVENT_TEMP_THRESHOLD:
-		desc = "Temperature Threshold";
-		break;
 	case MPI3_EVENT_CABLE_MGMT:
 		desc = "Cable Management";
 		break;
@@ -287,8 +299,14 @@
 	switch (host_tag) {
 	case MPI3MR_HOSTTAG_INITCMDS:
 		return &mrioc->init_cmds;
+	case MPI3MR_HOSTTAG_BSG_CMDS:
+		return &mrioc->bsg_cmds;
 	case MPI3MR_HOSTTAG_BLK_TMS:
 		return &mrioc->host_tm_cmds;
+	case MPI3MR_HOSTTAG_PEL_ABORT:
+		return &mrioc->pel_abort_cmd;
+	case MPI3MR_HOSTTAG_PEL_WAIT:
+		return &mrioc->pel_cmds;
 	case MPI3MR_HOSTTAG_INVALID:
 		if (def_reply && def_reply->function ==
 		    MPI3_FUNCTION_EVENT_NOTIFICATION)
@@ -303,6 +321,12 @@
 		return &mrioc->dev_rmhs_cmds[idx];
 	}
 
+	if (host_tag >= MPI3MR_HOSTTAG_EVTACKCMD_MIN &&
+	    host_tag <= MPI3MR_HOSTTAG_EVTACKCMD_MAX) {
+		idx = host_tag - MPI3MR_HOSTTAG_EVTACKCMD_MIN;
+		return &mrioc->evtack_cmds[idx];
+	}
+
 	return NULL;
 }
 
@@ -369,7 +393,7 @@
 			if (def_reply) {
 				cmdptr->state |= MPI3MR_CMD_REPLY_VALID;
 				memcpy((u8 *)cmdptr->reply, (u8 *)def_reply,
-				    mrioc->facts.reply_sz);
+				    mrioc->reply_sz);
 			}
 			if (cmdptr->is_waiting) {
 				complete(&cmdptr->done);
@@ -446,10 +470,21 @@
 	return reply_desc;
 }
 
-static int mpi3mr_process_op_reply_q(struct mpi3mr_ioc *mrioc,
-	struct mpi3mr_intr_info *intr_info)
+/**
+ * mpi3mr_process_op_reply_q - Operational reply queue handler
+ * @mrioc: Adapter instance reference
+ * @op_reply_q: Operational reply queue info
+ *
+ * Checks the specific operational reply queue and drains the
+ * reply queue entries until the queue is empty and process the
+ * individual reply descriptors.
+ *
+ * Return: 0 if queue is already processed,or number of reply
+ *	    descriptors processed.
+ */
+int mpi3mr_process_op_reply_q(struct mpi3mr_ioc *mrioc,
+	struct op_reply_qinfo *op_reply_q)
 {
-	struct op_reply_qinfo *op_reply_q = intr_info->op_reply_q;
 	struct op_req_qinfo *op_req_q;
 	u32 exp_phase;
 	u32 reply_ci;
@@ -500,7 +535,7 @@
 		 * Ensure remaining completion happens from threaded ISR.
 		 */
 		if (num_op_reply > mrioc->max_host_ios) {
-			intr_info->op_reply_q->enable_irq_poll = true;
+			op_reply_q->enable_irq_poll = true;
 			break;
 		}
 
@@ -515,6 +550,34 @@
 	return num_op_reply;
 }
 
+/**
+ * mpi3mr_blk_mq_poll - Operational reply queue handler
+ * @shost: SCSI Host reference
+ * @queue_num: Request queue number (w.r.t OS it is hardware context number)
+ *
+ * Checks the specific operational reply queue and drains the
+ * reply queue entries until the queue is empty and process the
+ * individual reply descriptors.
+ *
+ * Return: 0 if queue is already processed,or number of reply
+ *	    descriptors processed.
+ */
+int mpi3mr_blk_mq_poll(struct Scsi_Host *shost, unsigned int queue_num)
+{
+	int num_entries = 0;
+	struct mpi3mr_ioc *mrioc;
+
+	mrioc = (struct mpi3mr_ioc *)shost->hostdata;
+
+	if ((mrioc->reset_in_progress || mrioc->prepare_for_reset))
+		return 0;
+
+	num_entries = mpi3mr_process_op_reply_q(mrioc,
+			&mrioc->op_reply_qinfo[queue_num]);
+
+	return num_entries;
+}
+
 static irqreturn_t mpi3mr_isr_primary(int irq, void *privdata)
 {
 	struct mpi3mr_intr_info *intr_info = privdata;
@@ -535,7 +598,8 @@
 	if (!midx)
 		num_admin_replies = mpi3mr_process_admin_reply_q(mrioc);
 	if (intr_info->op_reply_q)
-		num_op_reply = mpi3mr_process_op_reply_q(mrioc, intr_info);
+		num_op_reply = mpi3mr_process_op_reply_q(mrioc,
+		    intr_info->op_reply_q);
 
 	if (num_admin_replies || num_op_reply)
 		return IRQ_HANDLED;
@@ -606,9 +670,10 @@
 			mpi3mr_process_admin_reply_q(mrioc);
 		if (intr_info->op_reply_q)
 			num_op_reply +=
-			    mpi3mr_process_op_reply_q(mrioc, intr_info);
+			    mpi3mr_process_op_reply_q(mrioc,
+				intr_info->op_reply_q);
 
-		usleep_range(mrioc->irqpoll_sleep, 10 * mrioc->irqpoll_sleep);
+		usleep_range(MPI3MR_IRQ_POLL_SLEEP, 10 * MPI3MR_IRQ_POLL_SLEEP);
 
 	} while (atomic_read(&intr_info->op_reply_q->pend_ios) &&
 	    (num_op_reply < mrioc->max_host_ios));
@@ -652,6 +717,25 @@
 	return retval;
 }
 
+static void mpi3mr_calc_poll_queues(struct mpi3mr_ioc *mrioc, u16 max_vectors)
+{
+	if (!mrioc->requested_poll_qcount)
+		return;
+
+	/* Reserved for Admin and Default Queue */
+	if (max_vectors > 2 &&
+		(mrioc->requested_poll_qcount < max_vectors - 2)) {
+		ioc_info(mrioc,
+		    "enabled polled queues (%d) msix (%d)\n",
+		    mrioc->requested_poll_qcount, max_vectors);
+	} else {
+		ioc_info(mrioc,
+		    "disabled polled queues (%d) msix (%d) because of no resources for default queue\n",
+		    mrioc->requested_poll_qcount, max_vectors);
+		mrioc->requested_poll_qcount = 0;
+	}
+}
+
 /**
  * mpi3mr_setup_isr - Setup ISR for the controller
  * @mrioc: Adapter instance reference
@@ -664,48 +748,72 @@
 static int mpi3mr_setup_isr(struct mpi3mr_ioc *mrioc, u8 setup_one)
 {
 	unsigned int irq_flags = PCI_IRQ_MSIX;
-	int max_vectors;
+	int max_vectors, min_vec;
 	int retval;
 	int i;
-	struct irq_affinity desc = { .pre_vectors =  1};
+	struct irq_affinity desc = { .pre_vectors =  1, .post_vectors = 1 };
+
+	if (mrioc->is_intr_info_set)
+		return 0;
 
 	mpi3mr_cleanup_isr(mrioc);
 
-	if (setup_one || reset_devices)
+	if (setup_one || reset_devices) {
 		max_vectors = 1;
-	else {
+		retval = pci_alloc_irq_vectors(mrioc->pdev,
+		    1, max_vectors, irq_flags);
+		if (retval < 0) {
+			ioc_err(mrioc, "cannot allocate irq vectors, ret %d\n",
+			    retval);
+			goto out_failed;
+		}
+	} else {
 		max_vectors =
-		    min_t(int, mrioc->cpu_count + 1, mrioc->msix_count);
+		    min_t(int, mrioc->cpu_count + 1 +
+			mrioc->requested_poll_qcount, mrioc->msix_count);
+
+		mpi3mr_calc_poll_queues(mrioc, max_vectors);
 
 		ioc_info(mrioc,
 		    "MSI-X vectors supported: %d, no of cores: %d,",
 		    mrioc->msix_count, mrioc->cpu_count);
 		ioc_info(mrioc,
-		    "MSI-x vectors requested: %d\n", max_vectors);
-	}
+		    "MSI-x vectors requested: %d poll_queues %d\n",
+		    max_vectors, mrioc->requested_poll_qcount);
+
+		desc.post_vectors = mrioc->requested_poll_qcount;
+		min_vec = desc.pre_vectors + desc.post_vectors;
+		irq_flags |= PCI_IRQ_AFFINITY | PCI_IRQ_ALL_TYPES;
+
+		retval = pci_alloc_irq_vectors_affinity(mrioc->pdev,
+			min_vec, max_vectors, irq_flags, &desc);
+
+		if (retval < 0) {
+			ioc_err(mrioc, "cannot allocate irq vectors, ret %d\n",
+			    retval);
+			goto out_failed;
+		}
 
-	irq_flags |= PCI_IRQ_AFFINITY | PCI_IRQ_ALL_TYPES;
 
-	mrioc->op_reply_q_offset = (max_vectors > 1) ? 1 : 0;
-	retval = pci_alloc_irq_vectors_affinity(mrioc->pdev,
-				1, max_vectors, irq_flags, &desc);
-	if (retval < 0) {
-		ioc_err(mrioc, "Cannot alloc irq vectors\n");
-		goto out_failed;
-	}
-	if (retval != max_vectors) {
-		ioc_info(mrioc,
-		    "allocated vectors (%d) are less than configured (%d)\n",
-		    retval, max_vectors);
 		/*
 		 * If only one MSI-x is allocated, then MSI-x 0 will be shared
 		 * between Admin queue and operational queue
 		 */
-		if (retval == 1)
+		if (retval == min_vec)
 			mrioc->op_reply_q_offset = 0;
+		else if (retval != (max_vectors)) {
+			ioc_info(mrioc,
+			    "allocated vectors (%d) are less than configured (%d)\n",
+			    retval, max_vectors);
+		}
 
 		max_vectors = retval;
+		mrioc->op_reply_q_offset = (max_vectors > 1) ? 1 : 0;
+
+		mpi3mr_calc_poll_queues(mrioc, max_vectors);
+
 	}
+
 	mrioc->intr_info = kzalloc(sizeof(struct mpi3mr_intr_info) * max_vectors,
 	    GFP_KERNEL);
 	if (!mrioc->intr_info) {
@@ -720,6 +828,8 @@
 			goto out_failed;
 		}
 	}
+	if (reset_devices || !setup_one)
+		mrioc->is_intr_info_set = true;
 	mrioc->intr_info_count = max_vectors;
 	mpi3mr_ioc_enable_intr(mrioc);
 	return 0;
@@ -763,10 +873,10 @@
 } mpi3mr_reset_reason_codes[] = {
 	{ MPI3MR_RESET_FROM_BRINGUP, "timeout in bringup" },
 	{ MPI3MR_RESET_FROM_FAULT_WATCH, "fault" },
-	{ MPI3MR_RESET_FROM_IOCTL, "application invocation" },
+	{ MPI3MR_RESET_FROM_APP, "application invocation" },
 	{ MPI3MR_RESET_FROM_EH_HOS, "error handling" },
 	{ MPI3MR_RESET_FROM_TM_TIMEOUT, "TM timeout" },
-	{ MPI3MR_RESET_FROM_IOCTL_TIMEOUT, "IOCTL timeout" },
+	{ MPI3MR_RESET_FROM_APP_TIMEOUT, "application command timeout" },
 	{ MPI3MR_RESET_FROM_MUR_FAILURE, "MUR failure" },
 	{ MPI3MR_RESET_FROM_CTLR_CLEANUP, "timeout in controller cleanup" },
 	{ MPI3MR_RESET_FROM_CIACTIV_FAULT, "component image activation fault" },
@@ -796,6 +906,7 @@
 	},
 	{ MPI3MR_RESET_FROM_SYSFS, "sysfs invocation" },
 	{ MPI3MR_RESET_FROM_SYSFS_TIMEOUT, "sysfs TM timeout" },
+	{ MPI3MR_RESET_FROM_FIRMWARE, "firmware asynchronous reset" },
 };
 
 /**
@@ -860,7 +971,7 @@
  *
  * Return: Nothing.
  */
-static void mpi3mr_print_fault_info(struct mpi3mr_ioc *mrioc)
+void mpi3mr_print_fault_info(struct mpi3mr_ioc *mrioc)
 {
 	u32 ioc_status, code, code1, code2, code3;
 
@@ -958,25 +1069,25 @@
 	ioc_config &= ~MPI3_SYSIF_IOC_CONFIG_ENABLE_IOC;
 	writel(ioc_config, &mrioc->sysif_regs->ioc_configuration);
 
-	timeout = mrioc->ready_timeout * 10;
+	timeout = MPI3MR_RESET_ACK_TIMEOUT * 10;
 	do {
 		ioc_status = readl(&mrioc->sysif_regs->ioc_status);
 		if ((ioc_status & MPI3_SYSIF_IOC_STATUS_RESET_HISTORY)) {
 			mpi3mr_clear_reset_history(mrioc);
-			ioc_config =
-			    readl(&mrioc->sysif_regs->ioc_configuration);
-			if (!((ioc_status & MPI3_SYSIF_IOC_STATUS_READY) ||
-			      (ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT) ||
-			    (ioc_config & MPI3_SYSIF_IOC_CONFIG_ENABLE_IOC))) {
-				retval = 0;
-				break;
-			}
+			break;
+		}
+		if (ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT) {
+			mpi3mr_print_fault_info(mrioc);
+			break;
 		}
 		msleep(100);
 	} while (--timeout);
 
-	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
 	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
+	if (timeout && !((ioc_status & MPI3_SYSIF_IOC_STATUS_READY) ||
+	      (ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT) ||
+	      (ioc_config & MPI3_SYSIF_IOC_CONFIG_ENABLE_IOC)))
+		retval = 0;
 
 	ioc_info(mrioc, "Base IOC Sts/Config after %s MUR is (0x%x)/(0x%x)\n",
 	    (!retval) ? "successful" : "failed", ioc_status, ioc_config);
@@ -984,32 +1095,171 @@
 }
 
 /**
+ * mpi3mr_revalidate_factsdata - validate IOCFacts parameters
+ * during reset/resume
+ * @mrioc: Adapter instance reference
+ *
+ * Return zero if the new IOCFacts parameters value is compatible with
+ * older values else return -EPERM
+ */
+static int
+mpi3mr_revalidate_factsdata(struct mpi3mr_ioc *mrioc)
+{
+	u16 dev_handle_bitmap_sz;
+	void *removepend_bitmap;
+
+	if (mrioc->facts.reply_sz > mrioc->reply_sz) {
+		ioc_err(mrioc,
+		    "cannot increase reply size from %d to %d\n",
+		    mrioc->reply_sz, mrioc->facts.reply_sz);
+		return -EPERM;
+	}
+
+	if (mrioc->facts.max_op_reply_q < mrioc->num_op_reply_q) {
+		ioc_err(mrioc,
+		    "cannot reduce number of operational reply queues from %d to %d\n",
+		    mrioc->num_op_reply_q,
+		    mrioc->facts.max_op_reply_q);
+		return -EPERM;
+	}
+
+	if (mrioc->facts.max_op_req_q < mrioc->num_op_req_q) {
+		ioc_err(mrioc,
+		    "cannot reduce number of operational request queues from %d to %d\n",
+		    mrioc->num_op_req_q, mrioc->facts.max_op_req_q);
+		return -EPERM;
+	}
+
+	dev_handle_bitmap_sz = mrioc->facts.max_devhandle / 8;
+	if (mrioc->facts.max_devhandle % 8)
+		dev_handle_bitmap_sz++;
+	if (dev_handle_bitmap_sz > mrioc->dev_handle_bitmap_sz) {
+		removepend_bitmap = krealloc(mrioc->removepend_bitmap,
+		    dev_handle_bitmap_sz, GFP_KERNEL);
+		if (!removepend_bitmap) {
+			ioc_err(mrioc,
+			    "failed to increase removepend_bitmap sz from: %d to %d\n",
+			    mrioc->dev_handle_bitmap_sz, dev_handle_bitmap_sz);
+			return -EPERM;
+		}
+		memset(removepend_bitmap + mrioc->dev_handle_bitmap_sz, 0,
+		    dev_handle_bitmap_sz - mrioc->dev_handle_bitmap_sz);
+		mrioc->removepend_bitmap = removepend_bitmap;
+		ioc_info(mrioc,
+		    "increased dev_handle_bitmap_sz from %d to %d\n",
+		    mrioc->dev_handle_bitmap_sz, dev_handle_bitmap_sz);
+		mrioc->dev_handle_bitmap_sz = dev_handle_bitmap_sz;
+	}
+
+	return 0;
+}
+
+/**
  * mpi3mr_bring_ioc_ready - Bring controller to ready state
  * @mrioc: Adapter instance reference
  *
  * Set Enable IOC bit in IOC configuration register and wait for
  * the controller to become ready.
  *
- * Return: 0 on success, -1 on failure.
+ * Return: 0 on success, appropriate error on failure.
  */
 static int mpi3mr_bring_ioc_ready(struct mpi3mr_ioc *mrioc)
 {
-	u32 ioc_config, timeout;
-	enum mpi3mr_iocstate current_state;
+	u32 ioc_config, ioc_status, timeout;
+	int retval = 0;
+	enum mpi3mr_iocstate ioc_state;
+	u64 base_info;
 
+	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
+	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
+	base_info = lo_hi_readq(&mrioc->sysif_regs->ioc_information);
+	ioc_info(mrioc, "ioc_status(0x%08x), ioc_config(0x%08x), ioc_info(0x%016llx) at the bringup\n",
+	    ioc_status, ioc_config, base_info);
+
+	/*The timeout value is in 2sec unit, changing it to seconds*/
+	mrioc->ready_timeout =
+	    ((base_info & MPI3_SYSIF_IOC_INFO_LOW_TIMEOUT_MASK) >>
+	    MPI3_SYSIF_IOC_INFO_LOW_TIMEOUT_SHIFT) * 2;
+
+	ioc_info(mrioc, "ready timeout: %d seconds\n", mrioc->ready_timeout);
+
+	ioc_state = mpi3mr_get_iocstate(mrioc);
+	ioc_info(mrioc, "controller is in %s state during detection\n",
+	    mpi3mr_iocstate_name(ioc_state));
+
+	if (ioc_state == MRIOC_STATE_BECOMING_READY ||
+	    ioc_state == MRIOC_STATE_RESET_REQUESTED) {
+		timeout = mrioc->ready_timeout * 10;
+		do {
+			msleep(100);
+		} while (--timeout);
+
+		ioc_state = mpi3mr_get_iocstate(mrioc);
+		ioc_info(mrioc,
+		    "controller is in %s state after waiting to reset\n",
+		    mpi3mr_iocstate_name(ioc_state));
+	}
+
+	if (ioc_state == MRIOC_STATE_READY) {
+		ioc_info(mrioc, "issuing message unit reset (MUR) to bring to reset state\n");
+		retval = mpi3mr_issue_and_process_mur(mrioc,
+		    MPI3MR_RESET_FROM_BRINGUP);
+		ioc_state = mpi3mr_get_iocstate(mrioc);
+		if (retval)
+			ioc_err(mrioc,
+			    "message unit reset failed with error %d current state %s\n",
+			    retval, mpi3mr_iocstate_name(ioc_state));
+	}
+	if (ioc_state != MRIOC_STATE_RESET) {
+		mpi3mr_print_fault_info(mrioc);
+		ioc_info(mrioc, "issuing soft reset to bring to reset state\n");
+		retval = mpi3mr_issue_reset(mrioc,
+		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET,
+		    MPI3MR_RESET_FROM_BRINGUP);
+		if (retval) {
+			ioc_err(mrioc,
+			    "soft reset failed with error %d\n", retval);
+			goto out_failed;
+		}
+	}
+	ioc_state = mpi3mr_get_iocstate(mrioc);
+	if (ioc_state != MRIOC_STATE_RESET) {
+		ioc_err(mrioc,
+		    "cannot bring controller to reset state, current state: %s\n",
+		    mpi3mr_iocstate_name(ioc_state));
+		goto out_failed;
+	}
+	mpi3mr_clear_reset_history(mrioc);
+	retval = mpi3mr_setup_admin_qpair(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "failed to setup admin queues: error %d\n",
+		    retval);
+		goto out_failed;
+	}
+
+	ioc_info(mrioc, "bringing controller to ready state\n");
 	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
 	ioc_config |= MPI3_SYSIF_IOC_CONFIG_ENABLE_IOC;
 	writel(ioc_config, &mrioc->sysif_regs->ioc_configuration);
 
 	timeout = mrioc->ready_timeout * 10;
 	do {
-		current_state = mpi3mr_get_iocstate(mrioc);
-		if (current_state == MRIOC_STATE_READY)
+		ioc_state = mpi3mr_get_iocstate(mrioc);
+		if (ioc_state == MRIOC_STATE_READY) {
+			ioc_info(mrioc,
+			    "successfully transitioned to %s state\n",
+			    mpi3mr_iocstate_name(ioc_state));
 			return 0;
+		}
 		msleep(100);
 	} while (--timeout);
 
-	return -1;
+out_failed:
+	ioc_state = mpi3mr_get_iocstate(mrioc);
+	ioc_err(mrioc,
+	    "failed to bring to ready state,  current state: %s\n",
+	    mpi3mr_iocstate_name(ioc_state));
+	return retval;
 }
 
 /**
@@ -1026,7 +1276,6 @@
 mpi3mr_soft_reset_success(u32 ioc_status, u32 ioc_config)
 {
 	if (!((ioc_status & MPI3_SYSIF_IOC_STATUS_READY) ||
-	    (ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT) ||
 	    (ioc_config & MPI3_SYSIF_IOC_CONFIG_ENABLE_IOC)))
 		return true;
 	return false;
@@ -1049,8 +1298,10 @@
 	if (!(ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT))
 		return false;
 	fault = readl(&mrioc->sysif_regs->fault) & MPI3_SYSIF_FAULT_CODE_MASK;
-	if (fault == MPI3_SYSIF_FAULT_CODE_DIAG_FAULT_RESET)
+	if (fault == MPI3_SYSIF_FAULT_CODE_DIAG_FAULT_RESET) {
+		mpi3mr_print_fault_info(mrioc);
 		return true;
+	}
 	return false;
 }
 
@@ -1089,26 +1340,36 @@
 	u32 reset_reason)
 {
 	int retval = -1;
-	u8 unlock_retry_count, reset_retry_count = 0;
-	u32 host_diagnostic, timeout, ioc_status, ioc_config;
+	u8 unlock_retry_count = 0;
+	u32 host_diagnostic, ioc_status, ioc_config;
+	u32 timeout = MPI3MR_RESET_ACK_TIMEOUT * 10;
 
-	pci_cfg_access_lock(mrioc->pdev);
 	if ((reset_type != MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET) &&
 	    (reset_type != MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT))
-		goto out;
+		return retval;
 	if (mrioc->unrecoverable)
-		goto out;
-retry_reset:
-	unlock_retry_count = 0;
+		return retval;
+	if (reset_reason == MPI3MR_RESET_FROM_FIRMWARE) {
+		retval = 0;
+		return retval;
+	}
+
+	ioc_info(mrioc, "%s reset due to %s(0x%x)\n",
+	    mpi3mr_reset_type_name(reset_type),
+	    mpi3mr_reset_rc_name(reset_reason), reset_reason);
+
 	mpi3mr_clear_reset_history(mrioc);
 	do {
 		ioc_info(mrioc,
 		    "Write magic sequence to unlock host diag register (retry=%d)\n",
 		    ++unlock_retry_count);
 		if (unlock_retry_count >= MPI3MR_HOSTDIAG_UNLOCK_RETRY_COUNT) {
-			writel(reset_reason, &mrioc->sysif_regs->scratchpad[0]);
+			ioc_err(mrioc,
+			    "%s reset failed due to unlock failure, host_diagnostic(0x%08x)\n",
+			    mpi3mr_reset_type_name(reset_type),
+			    host_diagnostic);
 			mrioc->unrecoverable = 1;
-			goto out;
+			return retval;
 		}
 
 		writel(MPI3_SYSIF_WRITE_SEQUENCE_KEY_VALUE_FLUSH,
@@ -1133,31 +1394,26 @@
 	} while (!(host_diagnostic & MPI3_SYSIF_HOST_DIAG_DIAG_WRITE_ENABLE));
 
 	writel(reset_reason, &mrioc->sysif_regs->scratchpad[0]);
-	ioc_info(mrioc, "%s reset due to %s(0x%x)\n",
-	    mpi3mr_reset_type_name(reset_type),
-	    mpi3mr_reset_rc_name(reset_reason), reset_reason);
 	writel(host_diagnostic | reset_type,
 	    &mrioc->sysif_regs->host_diagnostic);
-	timeout = mrioc->ready_timeout * 10;
-	if (reset_type == MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET) {
+	switch (reset_type) {
+	case MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET:
 		do {
 			ioc_status = readl(&mrioc->sysif_regs->ioc_status);
-			if (ioc_status &
-			    MPI3_SYSIF_IOC_STATUS_RESET_HISTORY) {
+			ioc_config =
+			    readl(&mrioc->sysif_regs->ioc_configuration);
+			if ((ioc_status & MPI3_SYSIF_IOC_STATUS_RESET_HISTORY)
+			    && mpi3mr_soft_reset_success(ioc_status, ioc_config)
+			    ) {
 				mpi3mr_clear_reset_history(mrioc);
-				ioc_config =
-				    readl(&mrioc->sysif_regs->ioc_configuration);
-				if (mpi3mr_soft_reset_success(ioc_status,
-				    ioc_config)) {
-					retval = 0;
-					break;
-				}
+				retval = 0;
+				break;
 			}
 			msleep(100);
 		} while (--timeout);
-		writel(MPI3_SYSIF_WRITE_SEQUENCE_KEY_VALUE_2ND,
-		    &mrioc->sysif_regs->write_sequence);
-	} else if (reset_type == MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT) {
+		mpi3mr_print_fault_info(mrioc);
+		break;
+	case MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT:
 		do {
 			ioc_status = readl(&mrioc->sysif_regs->ioc_status);
 			if (mpi3mr_diagfault_success(mrioc, ioc_status)) {
@@ -1166,28 +1422,22 @@
 			}
 			msleep(100);
 		} while (--timeout);
-		mpi3mr_clear_reset_history(mrioc);
-		writel(MPI3_SYSIF_WRITE_SEQUENCE_KEY_VALUE_2ND,
-		    &mrioc->sysif_regs->write_sequence);
-	}
-	if (retval && ((++reset_retry_count) < MPI3MR_MAX_RESET_RETRY_COUNT)) {
-		ioc_status = readl(&mrioc->sysif_regs->ioc_status);
-		ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
-		ioc_info(mrioc,
-		    "Base IOC Sts/Config after reset try %d is (0x%x)/(0x%x)\n",
-		    reset_retry_count, ioc_status, ioc_config);
-		goto retry_reset;
+		break;
+	default:
+		break;
 	}
 
-out:
-	pci_cfg_access_unlock(mrioc->pdev);
-	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
-	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
+	writel(MPI3_SYSIF_WRITE_SEQUENCE_KEY_VALUE_2ND,
+	    &mrioc->sysif_regs->write_sequence);
 
+	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
+	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
 	ioc_info(mrioc,
-	    "Base IOC Sts/Config after %s reset is (0x%x)/(0x%x)\n",
-	    (!retval) ? "successful" : "failed", ioc_status,
+	    "ioc_status/ioc_onfig after %s reset is (0x%x)/(0x%x)\n",
+	    (!retval)?"successful":"failed", ioc_status,
 	    ioc_config);
+	if (retval)
+		mrioc->unrecoverable = 1;
 	return retval;
 }
 
@@ -1275,10 +1525,10 @@
 			    MPI3MR_MAX_SEG_LIST_SIZE,
 			    mrioc->req_qinfo[q_idx].q_segment_list,
 			    mrioc->req_qinfo[q_idx].q_segment_list_dma);
-			mrioc->op_reply_qinfo[q_idx].q_segment_list = NULL;
+			mrioc->req_qinfo[q_idx].q_segment_list = NULL;
 		}
 	} else
-		size = mrioc->req_qinfo[q_idx].num_requests *
+		size = mrioc->req_qinfo[q_idx].segment_qd *
 		    mrioc->facts.op_req_sz;
 
 	for (j = 0; j < mrioc->req_qinfo[q_idx].num_segments; j++) {
@@ -1351,10 +1601,11 @@
 static int mpi3mr_delete_op_reply_q(struct mpi3mr_ioc *mrioc, u16 qidx)
 {
 	struct mpi3_delete_reply_queue_request delq_req;
+	struct op_reply_qinfo *op_reply_q = mrioc->op_reply_qinfo + qidx;
 	int retval = 0;
 	u16 reply_qid = 0, midx;
 
-	reply_qid = mrioc->op_reply_qinfo[qidx].qid;
+	reply_qid = op_reply_q->qid;
 
 	midx = REPLY_QUEUE_IDX_TO_MSIX_IDX(qidx, mrioc->op_reply_q_offset);
 
@@ -1364,6 +1615,9 @@
 		goto out;
 	}
 
+	(op_reply_q->qtype == MPI3MR_DEFAULT_QUEUE) ? mrioc->default_qcount-- :
+	    mrioc->active_poll_qcount--;
+
 	memset(&delq_req, 0, sizeof(delq_req));
 	mutex_lock(&mrioc->init_cmds.mutex);
 	if (mrioc->init_cmds.state & MPI3MR_CMD_PENDING) {
@@ -1389,13 +1643,9 @@
 	wait_for_completion_timeout(&mrioc->init_cmds.done,
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-		ioc_err(mrioc, "Issue DelRepQ: command timed out\n");
-		mpi3mr_set_diagsave(mrioc);
-		mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+		ioc_err(mrioc, "delete reply queue timed out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
 		    MPI3MR_RESET_FROM_DELREPQ_TIMEOUT);
-		mrioc->unrecoverable = 1;
-
 		retval = -1;
 		goto out_unlock;
 	}
@@ -1565,6 +1815,8 @@
 
 	reply_qid = qidx + 1;
 	op_reply_q->num_replies = MPI3MR_OP_REP_Q_QD;
+	if (!mrioc->pdev->revision)
+		op_reply_q->num_replies = MPI3MR_OP_REP_Q_QD4K;
 	op_reply_q->ci = 0;
 	op_reply_q->ephase = 1;
 	atomic_set(&op_reply_q->pend_ios, 0);
@@ -1592,8 +1844,26 @@
 	create_req.host_tag = cpu_to_le16(MPI3MR_HOSTTAG_INITCMDS);
 	create_req.function = MPI3_FUNCTION_CREATE_REPLY_QUEUE;
 	create_req.queue_id = cpu_to_le16(reply_qid);
-	create_req.flags = MPI3_CREATE_REPLY_QUEUE_FLAGS_INT_ENABLE_ENABLE;
-	create_req.msix_index = cpu_to_le16(mrioc->intr_info[midx].msix_index);
+
+	if (midx < (mrioc->intr_info_count - mrioc->requested_poll_qcount))
+		op_reply_q->qtype = MPI3MR_DEFAULT_QUEUE;
+	else
+		op_reply_q->qtype = MPI3MR_POLL_QUEUE;
+
+	if (op_reply_q->qtype == MPI3MR_DEFAULT_QUEUE) {
+		create_req.flags =
+			MPI3_CREATE_REPLY_QUEUE_FLAGS_INT_ENABLE_ENABLE;
+		create_req.msix_index =
+			cpu_to_le16(mrioc->intr_info[midx].msix_index);
+	} else {
+		create_req.msix_index = cpu_to_le16(mrioc->intr_info_count - 1);
+		ioc_info(mrioc, "create reply queue(polled): for qid(%d), midx(%d)\n",
+			reply_qid, midx);
+		if (!mrioc->active_poll_qcount)
+			disable_irq_nosync(pci_irq_vector(mrioc->pdev,
+			    mrioc->intr_info_count - 1));
+	}
+
 	if (mrioc->enable_segqueue) {
 		create_req.flags |=
 		    MPI3_CREATE_REQUEST_QUEUE_FLAGS_SEGMENTED_SEGMENTED;
@@ -1615,12 +1885,9 @@
 	wait_for_completion_timeout(&mrioc->init_cmds.done,
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-		ioc_err(mrioc, "CreateRepQ: command timed out\n");
-		mpi3mr_set_diagsave(mrioc);
-		mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+		ioc_err(mrioc, "create reply queue timed out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
 		    MPI3MR_RESET_FROM_CREATEREPQ_TIMEOUT);
-		mrioc->unrecoverable = 1;
 		retval = -1;
 		goto out_unlock;
 	}
@@ -1634,7 +1901,11 @@
 		goto out_unlock;
 	}
 	op_reply_q->qid = reply_qid;
-	mrioc->intr_info[midx].op_reply_q = op_reply_q;
+	if (midx < mrioc->intr_info_count)
+		mrioc->intr_info[midx].op_reply_q = op_reply_q;
+
+	(op_reply_q->qtype == MPI3MR_DEFAULT_QUEUE) ? mrioc->default_qcount++ :
+	    mrioc->active_poll_qcount++;
 
 out_unlock:
 	mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
@@ -1722,12 +1993,9 @@
 	wait_for_completion_timeout(&mrioc->init_cmds.done,
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-		ioc_err(mrioc, "CreateReqQ: command timed out\n");
-		mpi3mr_set_diagsave(mrioc);
-		if (mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
-		    MPI3MR_RESET_FROM_CREATEREQQ_TIMEOUT))
-			mrioc->unrecoverable = 1;
+		ioc_err(mrioc, "create request queue timed out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
+		    MPI3MR_RESET_FROM_CREATEREQQ_TIMEOUT);
 		retval = -1;
 		goto out_unlock;
 	}
@@ -1771,8 +2039,13 @@
 	    mrioc->intr_info_count - mrioc->op_reply_q_offset;
 	if (!mrioc->num_queues)
 		mrioc->num_queues = min_t(int, num_queues, msix_count_op_q);
-	num_queues = mrioc->num_queues;
-	ioc_info(mrioc, "Trying to create %d Operational Q pairs\n",
+	/*
+	 * During reset set the num_queues to the number of queues
+	 * that was set before the reset.
+	 */
+	num_queues = mrioc->num_op_reply_q ?
+	    mrioc->num_op_reply_q : mrioc->num_queues;
+	ioc_info(mrioc, "trying to create %d operational queue pairs\n",
 	    num_queues);
 
 	if (!mrioc->req_qinfo) {
@@ -1814,8 +2087,10 @@
 		goto out_failed;
 	}
 	mrioc->num_op_reply_q = mrioc->num_op_req_q = i;
-	ioc_info(mrioc, "Successfully created %d Operational Q pairs\n",
-	    mrioc->num_op_reply_q);
+	ioc_info(mrioc,
+	    "successfully created %d operational queue pairs(default/polled) queue = (%d/%d)\n",
+	    mrioc->num_op_reply_q, mrioc->default_qcount,
+	    mrioc->active_poll_qcount);
 
 	return retval;
 out_failed:
@@ -1863,7 +2138,7 @@
 	if (mpi3mr_check_req_qfull(op_req_q)) {
 		midx = REPLY_QUEUE_IDX_TO_MSIX_IDX(
 		    reply_qidx, mrioc->op_reply_q_offset);
-		mpi3mr_process_op_reply_q(mrioc, &mrioc->intr_info[midx]);
+		mpi3mr_process_op_reply_q(mrioc, mrioc->intr_info[midx].op_reply_q);
 
 		if (mpi3mr_check_req_qfull(op_req_q)) {
 			retval = -EAGAIN;
@@ -1901,6 +2176,42 @@
 }
 
 /**
+ * mpi3mr_check_rh_fault_ioc - check reset history and fault
+ * controller
+ * @mrioc: Adapter instance reference
+ * @reason_code: reason code for the fault.
+ *
+ * This routine will save snapdump and fault the controller with
+ * the given reason code if it is not already in the fault or
+ * not asynchronosuly reset. This will be used to handle
+ * initilaization time faults/resets/timeout as in those cases
+ * immediate soft reset invocation is not required.
+ *
+ * Return:  None.
+ */
+void mpi3mr_check_rh_fault_ioc(struct mpi3mr_ioc *mrioc, u32 reason_code)
+{
+	u32 ioc_status, host_diagnostic, timeout;
+
+	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
+	if ((ioc_status & MPI3_SYSIF_IOC_STATUS_RESET_HISTORY) ||
+	    (ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT)) {
+		mpi3mr_print_fault_info(mrioc);
+		return;
+	}
+	mpi3mr_set_diagsave(mrioc);
+	mpi3mr_issue_reset(mrioc, MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+	    reason_code);
+	timeout = MPI3_SYSIF_DIAG_SAVE_TIMEOUT * 10;
+	do {
+		host_diagnostic = readl(&mrioc->sysif_regs->host_diagnostic);
+		if (!(host_diagnostic & MPI3_SYSIF_HOST_DIAG_SAVE_IN_PROGRESS))
+			break;
+		msleep(100);
+	} while (--timeout);
+}
+
+/**
  * mpi3mr_sync_timestamp - Issue time stamp sync request
  * @mrioc: Adapter reference
  *
@@ -1945,8 +2256,9 @@
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
 		ioc_err(mrioc, "Issue IOUCTL time_stamp: command timed out\n");
 		mrioc->init_cmds.is_waiting = 0;
-		mpi3mr_soft_reset_handler(mrioc,
-		    MPI3MR_RESET_FROM_TSU_TIMEOUT, 1);
+		if (!(mrioc->init_cmds.state & MPI3MR_CMD_RESET))
+			mpi3mr_soft_reset_handler(mrioc,
+			    MPI3MR_RESET_FROM_TSU_TIMEOUT, 1);
 		retval = -1;
 		goto out_unlock;
 	}
@@ -1969,6 +2281,91 @@
 }
 
 /**
+ * mpi3mr_print_pkg_ver - display controller fw package version
+ * @mrioc: Adapter reference
+ *
+ * Retrieve firmware package version from the component image
+ * header of the controller flash and display it.
+ *
+ * Return: 0 on success and non-zero on failure.
+ */
+static int mpi3mr_print_pkg_ver(struct mpi3mr_ioc *mrioc)
+{
+	struct mpi3_ci_upload_request ci_upload;
+	int retval = -1;
+	void *data = NULL;
+	dma_addr_t data_dma;
+	struct mpi3_ci_manifest_mpi *manifest;
+	u32 data_len = sizeof(struct mpi3_ci_manifest_mpi);
+	u8 sgl_flags = MPI3MR_SGEFLAGS_SYSTEM_SIMPLE_END_OF_LIST;
+
+	data = dma_alloc_coherent(&mrioc->pdev->dev, data_len, &data_dma,
+	    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	memset(&ci_upload, 0, sizeof(ci_upload));
+	mutex_lock(&mrioc->init_cmds.mutex);
+	if (mrioc->init_cmds.state & MPI3MR_CMD_PENDING) {
+		ioc_err(mrioc, "sending get package version failed due to command in use\n");
+		mutex_unlock(&mrioc->init_cmds.mutex);
+		goto out;
+	}
+	mrioc->init_cmds.state = MPI3MR_CMD_PENDING;
+	mrioc->init_cmds.is_waiting = 1;
+	mrioc->init_cmds.callback = NULL;
+	ci_upload.host_tag = cpu_to_le16(MPI3MR_HOSTTAG_INITCMDS);
+	ci_upload.function = MPI3_FUNCTION_CI_UPLOAD;
+	ci_upload.msg_flags = MPI3_CI_UPLOAD_MSGFLAGS_LOCATION_PRIMARY;
+	ci_upload.signature1 = cpu_to_le32(MPI3_IMAGE_HEADER_SIGNATURE1_MANIFEST);
+	ci_upload.image_offset = cpu_to_le32(MPI3_IMAGE_HEADER_SIZE);
+	ci_upload.segment_size = cpu_to_le32(data_len);
+
+	mpi3mr_add_sg_single(&ci_upload.sgl, sgl_flags, data_len,
+	    data_dma);
+	init_completion(&mrioc->init_cmds.done);
+	retval = mpi3mr_admin_request_post(mrioc, &ci_upload,
+	    sizeof(ci_upload), 1);
+	if (retval) {
+		ioc_err(mrioc, "posting get package version failed\n");
+		goto out_unlock;
+	}
+	wait_for_completion_timeout(&mrioc->init_cmds.done,
+	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
+	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
+		ioc_err(mrioc, "get package version timed out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
+		    MPI3MR_RESET_FROM_GETPKGVER_TIMEOUT);
+		retval = -1;
+		goto out_unlock;
+	}
+	if ((mrioc->init_cmds.ioc_status & MPI3_IOCSTATUS_STATUS_MASK)
+	    == MPI3_IOCSTATUS_SUCCESS) {
+		manifest = (struct mpi3_ci_manifest_mpi *) data;
+		if (manifest->manifest_type == MPI3_CI_MANIFEST_TYPE_MPI) {
+			ioc_info(mrioc,
+			    "firmware package version(%d.%d.%d.%d.%05d-%05d)\n",
+			    manifest->package_version.gen_major,
+			    manifest->package_version.gen_minor,
+			    manifest->package_version.phase_major,
+			    manifest->package_version.phase_minor,
+			    manifest->package_version.customer_id,
+			    manifest->package_version.build_num);
+		}
+	}
+	retval = 0;
+out_unlock:
+	mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
+	mutex_unlock(&mrioc->init_cmds.mutex);
+
+out:
+	if (data)
+		dma_free_coherent(&mrioc->pdev->dev, data_len, data,
+		    data_dma);
+	return retval;
+}
+
+/**
  * mpi3mr_watchdog_work - watchdog thread to monitor faults
  * @work: work struct
  *
@@ -1984,50 +2381,66 @@
 	    container_of(work, struct mpi3mr_ioc, watchdog_work.work);
 	unsigned long flags;
 	enum mpi3mr_iocstate ioc_state;
-	u32 fault, host_diagnostic;
+	u32 fault, host_diagnostic, ioc_status;
+	u32 reset_reason = MPI3MR_RESET_FROM_FAULT_WATCH;
+
+	if (mrioc->reset_in_progress || mrioc->unrecoverable)
+		return;
 
 	if (mrioc->ts_update_counter++ >= MPI3MR_TSUPDATE_INTERVAL) {
 		mrioc->ts_update_counter = 0;
 		mpi3mr_sync_timestamp(mrioc);
 	}
 
+	if ((mrioc->prepare_for_reset) &&
+	    ((mrioc->prepare_for_reset_timeout_counter++) >=
+	     MPI3MR_PREPARE_FOR_RESET_TIMEOUT)) {
+		mpi3mr_soft_reset_handler(mrioc,
+		    MPI3MR_RESET_FROM_CIACTVRST_TIMER, 1);
+		return;
+	}
+
+	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
+	if (ioc_status & MPI3_SYSIF_IOC_STATUS_RESET_HISTORY) {
+		mpi3mr_soft_reset_handler(mrioc, MPI3MR_RESET_FROM_FIRMWARE, 0);
+		return;
+	}
+
 	/*Check for fault state every one second and issue Soft reset*/
 	ioc_state = mpi3mr_get_iocstate(mrioc);
-	if (ioc_state == MRIOC_STATE_FAULT) {
-		fault = readl(&mrioc->sysif_regs->fault) &
-		    MPI3_SYSIF_FAULT_CODE_MASK;
-		host_diagnostic = readl(&mrioc->sysif_regs->host_diagnostic);
-		if (host_diagnostic & MPI3_SYSIF_HOST_DIAG_SAVE_IN_PROGRESS) {
-			if (!mrioc->diagsave_timeout) {
-				mpi3mr_print_fault_info(mrioc);
-				ioc_warn(mrioc, "Diag save in progress\n");
-			}
-			if ((mrioc->diagsave_timeout++) <=
-			    MPI3_SYSIF_DIAG_SAVE_TIMEOUT)
-				goto schedule_work;
-		} else
-			mpi3mr_print_fault_info(mrioc);
-		mrioc->diagsave_timeout = 0;
+	if (ioc_state != MRIOC_STATE_FAULT)
+		goto schedule_work;
 
-		if (fault == MPI3_SYSIF_FAULT_CODE_FACTORY_RESET) {
-			ioc_info(mrioc,
-			    "Factory Reset fault occurred marking controller as unrecoverable"
-			    );
-			mrioc->unrecoverable = 1;
-			goto out;
+	fault = readl(&mrioc->sysif_regs->fault) & MPI3_SYSIF_FAULT_CODE_MASK;
+	host_diagnostic = readl(&mrioc->sysif_regs->host_diagnostic);
+	if (host_diagnostic & MPI3_SYSIF_HOST_DIAG_SAVE_IN_PROGRESS) {
+		if (!mrioc->diagsave_timeout) {
+			mpi3mr_print_fault_info(mrioc);
+			ioc_warn(mrioc, "diag save in progress\n");
 		}
+		if ((mrioc->diagsave_timeout++) <= MPI3_SYSIF_DIAG_SAVE_TIMEOUT)
+			goto schedule_work;
+	}
 
-		if ((fault == MPI3_SYSIF_FAULT_CODE_DIAG_FAULT_RESET) ||
-		    (fault == MPI3_SYSIF_FAULT_CODE_SOFT_RESET_IN_PROGRESS) ||
-		    (mrioc->reset_in_progress))
-			goto out;
-		if (fault == MPI3_SYSIF_FAULT_CODE_CI_ACTIVATION_RESET)
-			mpi3mr_soft_reset_handler(mrioc,
-			    MPI3MR_RESET_FROM_CIACTIV_FAULT, 0);
-		else
-			mpi3mr_soft_reset_handler(mrioc,
-			    MPI3MR_RESET_FROM_FAULT_WATCH, 0);
+	mpi3mr_print_fault_info(mrioc);
+	mrioc->diagsave_timeout = 0;
+
+	switch (fault) {
+	case MPI3_SYSIF_FAULT_CODE_POWER_CYCLE_REQUIRED:
+		ioc_info(mrioc,
+		    "controller requires system power cycle, marking controller as unrecoverable\n");
+		mrioc->unrecoverable = 1;
+		return;
+	case MPI3_SYSIF_FAULT_CODE_SOFT_RESET_IN_PROGRESS:
+		return;
+	case MPI3_SYSIF_FAULT_CODE_CI_ACTIVATION_RESET:
+		reset_reason = MPI3MR_RESET_FROM_CIACTIV_FAULT;
+		break;
+	default:
+		break;
 	}
+	mpi3mr_soft_reset_handler(mrioc, reset_reason, 0);
+	return;
 
 schedule_work:
 	spin_lock_irqsave(&mrioc->watchdog_lock, flags);
@@ -2036,7 +2449,6 @@
 		    &mrioc->watchdog_work,
 		    msecs_to_jiffies(MPI3MR_WATCHDOG_INTERVAL));
 	spin_unlock_irqrestore(&mrioc->watchdog_lock, flags);
-out:
 	return;
 }
 
@@ -2097,41 +2509,6 @@
 }
 
 /**
- * mpi3mr_kill_ioc - Kill the controller
- * @mrioc: Adapter instance reference
- * @reason: reason for the failure.
- *
- * If fault debug is enabled, display the fault info else issue
- * diag fault and freeze the system for controller debug
- * purpose.
- *
- * Return: Nothing.
- */
-static void mpi3mr_kill_ioc(struct mpi3mr_ioc *mrioc, u32 reason)
-{
-	enum mpi3mr_iocstate ioc_state;
-
-	if (!mrioc->fault_dbg)
-		return;
-
-	dump_stack();
-
-	ioc_state = mpi3mr_get_iocstate(mrioc);
-	if (ioc_state == MRIOC_STATE_FAULT)
-		mpi3mr_print_fault_info(mrioc);
-	else {
-		ioc_err(mrioc, "Firmware is halted due to the reason %d\n",
-		    reason);
-		mpi3mr_diagfault_reset_handler(mrioc, reason);
-	}
-	if (mrioc->fault_dbg == 2)
-		for (;;)
-			;
-	else
-		panic("panic in %s\n", __func__);
-}
-
-/**
  * mpi3mr_setup_admin_qpair - Setup admin queue pair
  * @mrioc: Adapter instance reference
  *
@@ -2258,12 +2635,9 @@
 	wait_for_completion_timeout(&mrioc->init_cmds.done,
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-		ioc_err(mrioc, "Issue IOCFacts: command timed out\n");
-		mpi3mr_set_diagsave(mrioc);
-		mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+		ioc_err(mrioc, "ioc_facts timed out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
 		    MPI3MR_RESET_FROM_IOCFACTS_TIMEOUT);
-		mrioc->unrecoverable = 1;
 		retval = -1;
 		goto out_unlock;
 	}
@@ -2277,6 +2651,7 @@
 		goto out_unlock;
 	}
 	memcpy(facts_data, (u8 *)data, data_len);
+	mpi3mr_process_factsdata(mrioc, facts_data);
 out_unlock:
 	mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
 	mutex_unlock(&mrioc->init_cmds.mutex);
@@ -2369,19 +2744,18 @@
 	    MPI3_IOCFACTS_FLAGS_DMA_ADDRESS_WIDTH_SHIFT;
 	mrioc->facts.protocol_flags = facts_data->protocol_flags;
 	mrioc->facts.mpi_version = le32_to_cpu(facts_data->mpi_version.word);
-	mrioc->facts.max_reqs = le16_to_cpu(facts_data->max_outstanding_request);
+	mrioc->facts.max_reqs = le16_to_cpu(facts_data->max_outstanding_requests);
 	mrioc->facts.product_id = le16_to_cpu(facts_data->product_id);
 	mrioc->facts.reply_sz = le16_to_cpu(facts_data->reply_frame_size) * 4;
 	mrioc->facts.exceptions = le16_to_cpu(facts_data->ioc_exceptions);
 	mrioc->facts.max_perids = le16_to_cpu(facts_data->max_persistent_id);
-	mrioc->facts.max_pds = le16_to_cpu(facts_data->max_pds);
 	mrioc->facts.max_vds = le16_to_cpu(facts_data->max_vds);
 	mrioc->facts.max_hpds = le16_to_cpu(facts_data->max_host_pds);
-	mrioc->facts.max_advhpds = le16_to_cpu(facts_data->max_advanced_host_pds);
-	mrioc->facts.max_raidpds = le16_to_cpu(facts_data->max_raid_pds);
+	mrioc->facts.max_advhpds = le16_to_cpu(facts_data->max_adv_host_pds);
+	mrioc->facts.max_raid_pds = le16_to_cpu(facts_data->max_raid_pds);
 	mrioc->facts.max_nvme = le16_to_cpu(facts_data->max_nvme);
 	mrioc->facts.max_pcie_switches =
-	    le16_to_cpu(facts_data->max_pc_ie_switches);
+	    le16_to_cpu(facts_data->max_pcie_switches);
 	mrioc->facts.max_sasexpanders =
 	    le16_to_cpu(facts_data->max_sas_expanders);
 	mrioc->facts.max_sasinitiators =
@@ -2415,22 +2789,15 @@
 	    mrioc->facts.ioc_num, mrioc->facts.max_op_req_q,
 	    mrioc->facts.max_op_reply_q, mrioc->facts.max_devhandle);
 	ioc_info(mrioc,
-	    "maxreqs(%d), mindh(%d) maxPDs(%d) maxvectors(%d) maxperids(%d)\n",
+	    "maxreqs(%d), mindh(%d) maxvectors(%d) maxperids(%d)\n",
 	    mrioc->facts.max_reqs, mrioc->facts.min_devhandle,
-	    mrioc->facts.max_pds, mrioc->facts.max_msix_vectors,
-	    mrioc->facts.max_perids);
+	    mrioc->facts.max_msix_vectors, mrioc->facts.max_perids);
 	ioc_info(mrioc, "SGEModMask 0x%x SGEModVal 0x%x SGEModShift 0x%x ",
 	    mrioc->facts.sge_mod_mask, mrioc->facts.sge_mod_value,
 	    mrioc->facts.sge_mod_shift);
 	ioc_info(mrioc, "DMA mask %d InitialPE status 0x%x\n",
 	    mrioc->facts.dma_mask, (facts_flags &
 	    MPI3_IOCFACTS_FLAGS_INITIAL_PORT_ENABLE_MASK));
-
-	mrioc->max_host_ios = mrioc->facts.max_reqs - MPI3MR_INTERNAL_CMDS_RESVD;
-
-	if (reset_devices)
-		mrioc->max_host_ios = min_t(int, mrioc->max_host_ios,
-		    MPI3MR_HOST_IOS_KDUMP);
 }
 
 /**
@@ -2446,26 +2813,44 @@
 {
 	int retval = 0;
 	u32 sz, i;
-	dma_addr_t phy_addr;
 
 	if (mrioc->init_cmds.reply)
-		goto post_reply_sbuf;
+		return retval;
 
-	mrioc->init_cmds.reply = kzalloc(mrioc->facts.reply_sz, GFP_KERNEL);
+	mrioc->init_cmds.reply = kzalloc(mrioc->reply_sz, GFP_KERNEL);
 	if (!mrioc->init_cmds.reply)
 		goto out_failed;
 
+	mrioc->bsg_cmds.reply = kzalloc(mrioc->reply_sz, GFP_KERNEL);
+	if (!mrioc->bsg_cmds.reply)
+		goto out_failed;
+
 	for (i = 0; i < MPI3MR_NUM_DEVRMCMD; i++) {
-		mrioc->dev_rmhs_cmds[i].reply = kzalloc(mrioc->facts.reply_sz,
+		mrioc->dev_rmhs_cmds[i].reply = kzalloc(mrioc->reply_sz,
 		    GFP_KERNEL);
 		if (!mrioc->dev_rmhs_cmds[i].reply)
 			goto out_failed;
 	}
 
-	mrioc->host_tm_cmds.reply = kzalloc(mrioc->facts.reply_sz, GFP_KERNEL);
+	for (i = 0; i < MPI3MR_NUM_EVTACKCMD; i++) {
+		mrioc->evtack_cmds[i].reply = kzalloc(mrioc->reply_sz,
+		    GFP_KERNEL);
+		if (!mrioc->evtack_cmds[i].reply)
+			goto out_failed;
+	}
+
+	mrioc->host_tm_cmds.reply = kzalloc(mrioc->reply_sz, GFP_KERNEL);
 	if (!mrioc->host_tm_cmds.reply)
 		goto out_failed;
 
+	mrioc->pel_cmds.reply = kzalloc(mrioc->reply_sz, GFP_KERNEL);
+	if (!mrioc->pel_cmds.reply)
+		goto out_failed;
+
+	mrioc->pel_abort_cmd.reply = kzalloc(mrioc->reply_sz, GFP_KERNEL);
+	if (!mrioc->pel_abort_cmd.reply)
+		goto out_failed;
+
 	mrioc->dev_handle_bitmap_sz = mrioc->facts.max_devhandle / 8;
 	if (mrioc->facts.max_devhandle % 8)
 		mrioc->dev_handle_bitmap_sz++;
@@ -2482,13 +2867,21 @@
 	if (!mrioc->devrem_bitmap)
 		goto out_failed;
 
+	mrioc->evtack_cmds_bitmap_sz = MPI3MR_NUM_EVTACKCMD / 8;
+	if (MPI3MR_NUM_EVTACKCMD % 8)
+		mrioc->evtack_cmds_bitmap_sz++;
+	mrioc->evtack_cmds_bitmap = kzalloc(mrioc->evtack_cmds_bitmap_sz,
+	    GFP_KERNEL);
+	if (!mrioc->evtack_cmds_bitmap)
+		goto out_failed;
+
 	mrioc->num_reply_bufs = mrioc->facts.max_reqs + MPI3MR_NUM_EVT_REPLIES;
 	mrioc->reply_free_qsz = mrioc->num_reply_bufs + 1;
 	mrioc->num_sense_bufs = mrioc->facts.max_reqs / MPI3MR_SENSEBUF_FACTOR;
 	mrioc->sense_buf_q_sz = mrioc->num_sense_bufs + 1;
 
 	/* reply buffer pool, 16 byte align */
-	sz = mrioc->num_reply_bufs * mrioc->facts.reply_sz;
+	sz = mrioc->num_reply_bufs * mrioc->reply_sz;
 	mrioc->reply_buf_pool = dma_pool_create("reply_buf pool",
 	    &mrioc->pdev->dev, sz, 16, 0);
 	if (!mrioc->reply_buf_pool) {
@@ -2517,7 +2910,7 @@
 		goto out_failed;
 
 	/* sense buffer pool,  4 byte align */
-	sz = mrioc->num_sense_bufs * MPI3MR_SENSEBUF_SZ;
+	sz = mrioc->num_sense_bufs * MPI3MR_SENSE_BUF_SZ;
 	mrioc->sense_buf_pool = dma_pool_create("sense_buf pool",
 	    &mrioc->pdev->dev, sz, 4, 0);
 	if (!mrioc->sense_buf_pool) {
@@ -2542,21 +2935,42 @@
 	if (!mrioc->sense_buf_q)
 		goto out_failed;
 
-post_reply_sbuf:
-	sz = mrioc->num_reply_bufs * mrioc->facts.reply_sz;
+	return retval;
+
+out_failed:
+	retval = -1;
+	return retval;
+}
+
+/**
+ * mpimr_initialize_reply_sbuf_queues - initialize reply sense
+ * buffers
+ * @mrioc: Adapter instance reference
+ *
+ * Helper function to initialize reply and sense buffers along
+ * with some debug prints.
+ *
+ * Return:  None.
+ */
+static void mpimr_initialize_reply_sbuf_queues(struct mpi3mr_ioc *mrioc)
+{
+	u32 sz, i;
+	dma_addr_t phy_addr;
+
+	sz = mrioc->num_reply_bufs * mrioc->reply_sz;
 	ioc_info(mrioc,
 	    "reply buf pool(0x%p): depth(%d), frame_size(%d), pool_size(%d kB), reply_dma(0x%llx)\n",
-	    mrioc->reply_buf, mrioc->num_reply_bufs, mrioc->facts.reply_sz,
+	    mrioc->reply_buf, mrioc->num_reply_bufs, mrioc->reply_sz,
 	    (sz / 1024), (unsigned long long)mrioc->reply_buf_dma);
 	sz = mrioc->reply_free_qsz * 8;
 	ioc_info(mrioc,
 	    "reply_free_q pool(0x%p): depth(%d), frame_size(%d), pool_size(%d kB), reply_dma(0x%llx)\n",
 	    mrioc->reply_free_q, mrioc->reply_free_qsz, 8, (sz / 1024),
 	    (unsigned long long)mrioc->reply_free_q_dma);
-	sz = mrioc->num_sense_bufs * MPI3MR_SENSEBUF_SZ;
+	sz = mrioc->num_sense_bufs * MPI3MR_SENSE_BUF_SZ;
 	ioc_info(mrioc,
 	    "sense_buf pool(0x%p): depth(%d), frame_size(%d), pool_size(%d kB), sense_dma(0x%llx)\n",
-	    mrioc->sense_buf, mrioc->num_sense_bufs, MPI3MR_SENSEBUF_SZ,
+	    mrioc->sense_buf, mrioc->num_sense_bufs, MPI3MR_SENSE_BUF_SZ,
 	    (sz / 1024), (unsigned long long)mrioc->sense_buf_dma);
 	sz = mrioc->sense_buf_q_sz * 8;
 	ioc_info(mrioc,
@@ -2566,20 +2980,15 @@
 
 	/* initialize Reply buffer Queue */
 	for (i = 0, phy_addr = mrioc->reply_buf_dma;
-	    i < mrioc->num_reply_bufs; i++, phy_addr += mrioc->facts.reply_sz)
+	    i < mrioc->num_reply_bufs; i++, phy_addr += mrioc->reply_sz)
 		mrioc->reply_free_q[i] = cpu_to_le64(phy_addr);
 	mrioc->reply_free_q[i] = cpu_to_le64(0);
 
 	/* initialize Sense Buffer Queue */
 	for (i = 0, phy_addr = mrioc->sense_buf_dma;
-	    i < mrioc->num_sense_bufs; i++, phy_addr += MPI3MR_SENSEBUF_SZ)
+	    i < mrioc->num_sense_bufs; i++, phy_addr += MPI3MR_SENSE_BUF_SZ)
 		mrioc->sense_buf_q[i] = cpu_to_le64(phy_addr);
 	mrioc->sense_buf_q[i] = cpu_to_le64(0);
-	return retval;
-
-out_failed:
-	retval = -1;
-	return retval;
 }
 
 /**
@@ -2606,6 +3015,8 @@
 		retval = -1;
 		goto out;
 	}
+	mpimr_initialize_reply_sbuf_queues(mrioc);
+
 	drv_info->information_length = cpu_to_le32(data_len);
 	strscpy(drv_info->driver_signature, "Broadcom", sizeof(drv_info->driver_signature));
 	strscpy(drv_info->os_name, utsname()->sysname, sizeof(drv_info->os_name));
@@ -2639,7 +3050,7 @@
 	iocinit_req.reply_free_queue_depth = cpu_to_le16(mrioc->reply_free_qsz);
 	iocinit_req.reply_free_queue_address =
 	    cpu_to_le64(mrioc->reply_free_q_dma);
-	iocinit_req.sense_buffer_length = cpu_to_le16(MPI3MR_SENSEBUF_SZ);
+	iocinit_req.sense_buffer_length = cpu_to_le16(MPI3MR_SENSE_BUF_SZ);
 	iocinit_req.sense_buffer_free_queue_depth =
 	    cpu_to_le16(mrioc->sense_buf_q_sz);
 	iocinit_req.sense_buffer_free_queue_address =
@@ -2659,12 +3070,9 @@
 	wait_for_completion_timeout(&mrioc->init_cmds.done,
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-		mpi3mr_set_diagsave(mrioc);
-		mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+		mpi3mr_check_rh_fault_ioc(mrioc,
 		    MPI3MR_RESET_FROM_IOCINIT_TIMEOUT);
-		mrioc->unrecoverable = 1;
-		ioc_err(mrioc, "Issue IOCInit: command timed out\n");
+		ioc_err(mrioc, "ioc_init timed out\n");
 		retval = -1;
 		goto out_unlock;
 	}
@@ -2678,6 +3086,13 @@
 		goto out_unlock;
 	}
 
+	mrioc->reply_free_queue_host_index = mrioc->num_reply_bufs;
+	writel(mrioc->reply_free_queue_host_index,
+	    &mrioc->sysif_regs->reply_free_host_index);
+
+	mrioc->sbq_host_index = mrioc->num_sense_bufs;
+	writel(mrioc->sbq_host_index,
+	    &mrioc->sysif_regs->sense_buffer_free_host_index);
 out_unlock:
 	mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
 	mutex_unlock(&mrioc->init_cmds.mutex);
@@ -2755,12 +3170,9 @@
 	wait_for_completion_timeout(&mrioc->init_cmds.done,
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-		ioc_err(mrioc, "Issue EvtNotify: command timed out\n");
-		mpi3mr_set_diagsave(mrioc);
-		mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+		ioc_err(mrioc, "event notification timed out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
 		    MPI3MR_RESET_FROM_EVTNOTIFY_TIMEOUT);
-		mrioc->unrecoverable = 1;
 		retval = -1;
 		goto out_unlock;
 	}
@@ -2782,17 +3194,17 @@
 }
 
 /**
- * mpi3mr_send_event_ack - Send event acknowledgment
+ * mpi3mr_process_event_ack - Process event acknowledgment
  * @mrioc: Adapter instance reference
  * @event: MPI3 event ID
- * @event_ctx: Event context
+ * @event_ctx: event context
  *
  * Send event acknowledgment through admin queue and wait for
  * it to complete.
  *
  * Return: 0 on success, non-zero on failures.
  */
-int mpi3mr_send_event_ack(struct mpi3mr_ioc *mrioc, u8 event,
+int mpi3mr_process_event_ack(struct mpi3mr_ioc *mrioc, u8 event,
 	u32 event_ctx)
 {
 	struct mpi3_event_ack_request evtack_req;
@@ -2825,8 +3237,9 @@
 	    (MPI3MR_INTADMCMD_TIMEOUT * HZ));
 	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
 		ioc_err(mrioc, "Issue EvtNotify: command timed out\n");
-		mpi3mr_soft_reset_handler(mrioc,
-		    MPI3MR_RESET_FROM_EVTACK_TIMEOUT, 1);
+		if (!(mrioc->init_cmds.state & MPI3MR_CMD_RESET))
+			mpi3mr_soft_reset_handler(mrioc,
+			    MPI3MR_RESET_FROM_EVTACK_TIMEOUT, 1);
 		retval = -1;
 		goto out_unlock;
 	}
@@ -2863,6 +3276,9 @@
 	u32 sz, i;
 	u16 num_chains;
 
+	if (mrioc->chain_sgl_list)
+		return retval;
+
 	num_chains = mrioc->max_host_ios / MPI3MR_CHAINBUF_FACTOR;
 
 	if (prot_mask & (SHOST_DIX_TYPE0_PROTECTION
@@ -2966,29 +3382,28 @@
 		ioc_err(mrioc, "Issue PortEnable: Admin Post failed\n");
 		goto out_unlock;
 	}
-	if (!async) {
-		wait_for_completion_timeout(&mrioc->init_cmds.done,
-		    (pe_timeout * HZ));
-		if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
-			ioc_err(mrioc, "Issue PortEnable: command timed out\n");
-			retval = -1;
-			mrioc->scan_failed = MPI3_IOCSTATUS_INTERNAL_ERROR;
-			mpi3mr_set_diagsave(mrioc);
-			mpi3mr_issue_reset(mrioc,
-			    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
-			    MPI3MR_RESET_FROM_PE_TIMEOUT);
-			mrioc->unrecoverable = 1;
-			goto out_unlock;
-		}
-		mpi3mr_port_enable_complete(mrioc, &mrioc->init_cmds);
+	if (async) {
+		mutex_unlock(&mrioc->init_cmds.mutex);
+		goto out;
 	}
+
+	wait_for_completion_timeout(&mrioc->init_cmds.done, (pe_timeout * HZ));
+	if (!(mrioc->init_cmds.state & MPI3MR_CMD_COMPLETE)) {
+		ioc_err(mrioc, "port enable timed out\n");
+		retval = -1;
+		mpi3mr_check_rh_fault_ioc(mrioc, MPI3MR_RESET_FROM_PE_TIMEOUT);
+		goto out_unlock;
+	}
+	mpi3mr_port_enable_complete(mrioc, &mrioc->init_cmds);
+
 out_unlock:
+	mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
 	mutex_unlock(&mrioc->init_cmds.mutex);
 out:
 	return retval;
 }
 
-/* Protocol type to name mapper structure*/
+/* Protocol type to name mapper structure */
 static const struct {
 	u8 protocol;
 	char *name;
@@ -3018,11 +3433,10 @@
 static void
 mpi3mr_print_ioc_info(struct mpi3mr_ioc *mrioc)
 {
-	int i = 0, bytes_wrote = 0;
+	int i = 0, bytes_written = 0;
 	char personality[16];
 	char protocol[50] = {0};
 	char capabilities[100] = {0};
-	bool is_string_nonempty = false;
 	struct mpi3mr_compimg_ver *fwver = &mrioc->facts.fw_ver;
 
 	switch (mrioc->facts.personality) {
@@ -3046,39 +3460,26 @@
 	for (i = 0; i < ARRAY_SIZE(mpi3mr_protocols); i++) {
 		if (mrioc->facts.protocol_flags &
 		    mpi3mr_protocols[i].protocol) {
-			if (is_string_nonempty &&
-			    (bytes_wrote < sizeof(protocol)))
-				bytes_wrote += snprintf(protocol + bytes_wrote,
-				    (sizeof(protocol) - bytes_wrote), ",");
-
-			if (bytes_wrote < sizeof(protocol))
-				bytes_wrote += snprintf(protocol + bytes_wrote,
-				    (sizeof(protocol) - bytes_wrote), "%s",
+			bytes_written += scnprintf(protocol + bytes_written,
+				    sizeof(protocol) - bytes_written, "%s%s",
+				    bytes_written ? "," : "",
 				    mpi3mr_protocols[i].name);
-			is_string_nonempty = true;
 		}
 	}
 
-	bytes_wrote = 0;
-	is_string_nonempty = false;
+	bytes_written = 0;
 	for (i = 0; i < ARRAY_SIZE(mpi3mr_capabilities); i++) {
 		if (mrioc->facts.protocol_flags &
 		    mpi3mr_capabilities[i].capability) {
-			if (is_string_nonempty &&
-			    (bytes_wrote < sizeof(capabilities)))
-				bytes_wrote += snprintf(capabilities + bytes_wrote,
-				    (sizeof(capabilities) - bytes_wrote), ",");
-
-			if (bytes_wrote < sizeof(capabilities))
-				bytes_wrote += snprintf(capabilities + bytes_wrote,
-				    (sizeof(capabilities) - bytes_wrote), "%s",
+			bytes_written += scnprintf(capabilities + bytes_written,
+				    sizeof(capabilities) - bytes_written, "%s%s",
+				    bytes_written ? "," : "",
 				    mpi3mr_capabilities[i].name);
-			is_string_nonempty = true;
 		}
 	}
 
 	ioc_info(mrioc, "Protocol=(%s), Capabilities=(%s)\n",
-	    protocol, capabilities);
+		 protocol, capabilities);
 }
 
 /**
@@ -3195,6 +3596,10 @@
 	    mrioc->sysif_regs, memap_sz);
 	ioc_info(mrioc, "Number of MSI-X vectors found in capabilities: (%d)\n",
 	    mrioc->msix_count);
+
+	if (!reset_devices && poll_queues > 0)
+		mrioc->requested_poll_qcount = min_t(int, poll_queues,
+				mrioc->msix_count - 2);
 	return retval;
 
 out_failed:
@@ -3203,9 +3608,47 @@
 }
 
 /**
+ * mpi3mr_enable_events - Enable required events
+ * @mrioc: Adapter instance reference
+ *
+ * This routine unmasks the events required by the driver by
+ * sennding appropriate event mask bitmapt through an event
+ * notification request.
+ *
+ * Return: 0 on success and non-zero on failure.
+ */
+static int mpi3mr_enable_events(struct mpi3mr_ioc *mrioc)
+{
+	int retval = 0;
+	u32  i;
+
+	for (i = 0; i < MPI3_EVENT_NOTIFY_EVENTMASK_WORDS; i++)
+		mrioc->event_masks[i] = -1;
+
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_DEVICE_ADDED);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_DEVICE_INFO_CHANGED);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_DEVICE_STATUS_CHANGE);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_ENCL_DEVICE_STATUS_CHANGE);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_TOPOLOGY_CHANGE_LIST);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_DISCOVERY);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_DEVICE_DISCOVERY_ERROR);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_BROADCAST_PRIMITIVE);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_PCIE_TOPOLOGY_CHANGE_LIST);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_PCIE_ENUMERATION);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_PREPARE_FOR_RESET);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_CABLE_MGMT);
+	mpi3mr_unmask_events(mrioc, MPI3_EVENT_ENERGY_PACK_CHANGE);
+
+	retval = mpi3mr_issue_event_notification(mrioc);
+	if (retval)
+		ioc_err(mrioc, "failed to issue event notification %d\n",
+		    retval);
+	return retval;
+}
+
+/**
  * mpi3mr_init_ioc - Initialize the controller
  * @mrioc: Adapter instance reference
- * @init_type: Flag to indicate is the init_type
  *
  * This the controller initialization routine, executed either
  * after soft reset or from pci probe callback.
@@ -3218,227 +3661,264 @@
  *
  * Return: 0 on success and non-zero on failure.
  */
-int mpi3mr_init_ioc(struct mpi3mr_ioc *mrioc, u8 init_type)
+int mpi3mr_init_ioc(struct mpi3mr_ioc *mrioc)
 {
 	int retval = 0;
-	enum mpi3mr_iocstate ioc_state;
-	u64 base_info;
-	u32 timeout;
-	u32 ioc_status, ioc_config, i;
+	u8 retry = 0;
 	struct mpi3_ioc_facts_data facts_data;
 
-	mrioc->irqpoll_sleep = MPI3MR_IRQ_POLL_SLEEP;
-	mrioc->change_count = 0;
-	if (init_type == MPI3MR_IT_INIT) {
-		mrioc->cpu_count = num_online_cpus();
-		retval = mpi3mr_setup_resources(mrioc);
-		if (retval) {
-			ioc_err(mrioc, "Failed to setup resources:error %d\n",
-			    retval);
-			goto out_nocleanup;
-		}
+retry_init:
+	retval = mpi3mr_bring_ioc_ready(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "Failed to bring ioc ready: error %d\n",
+		    retval);
+		goto out_failed_noretry;
 	}
 
-	ioc_status = readl(&mrioc->sysif_regs->ioc_status);
-	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
+	retval = mpi3mr_setup_isr(mrioc, 1);
+	if (retval) {
+		ioc_err(mrioc, "Failed to setup ISR error %d\n",
+		    retval);
+		goto out_failed_noretry;
+	}
 
-	ioc_info(mrioc, "SOD status %x configuration %x\n",
-	    ioc_status, ioc_config);
+	retval = mpi3mr_issue_iocfacts(mrioc, &facts_data);
+	if (retval) {
+		ioc_err(mrioc, "Failed to Issue IOC Facts %d\n",
+		    retval);
+		goto out_failed;
+	}
 
-	base_info = lo_hi_readq(&mrioc->sysif_regs->ioc_information);
-	ioc_info(mrioc, "SOD base_info %llx\n",	base_info);
+	mrioc->max_host_ios = mrioc->facts.max_reqs - MPI3MR_INTERNAL_CMDS_RESVD;
 
-	/*The timeout value is in 2sec unit, changing it to seconds*/
-	mrioc->ready_timeout =
-	    ((base_info & MPI3_SYSIF_IOC_INFO_LOW_TIMEOUT_MASK) >>
-	    MPI3_SYSIF_IOC_INFO_LOW_TIMEOUT_SHIFT) * 2;
+	if (reset_devices)
+		mrioc->max_host_ios = min_t(int, mrioc->max_host_ios,
+		    MPI3MR_HOST_IOS_KDUMP);
 
-	ioc_info(mrioc, "IOC ready timeout %d\n", mrioc->ready_timeout);
+	mrioc->reply_sz = mrioc->facts.reply_sz;
 
-	ioc_state = mpi3mr_get_iocstate(mrioc);
-	ioc_info(mrioc, "IOC in %s state during detection\n",
-	    mpi3mr_iocstate_name(ioc_state));
+	retval = mpi3mr_check_reset_dma_mask(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "Resetting dma mask failed %d\n",
+		    retval);
+		goto out_failed_noretry;
+	}
 
-	if (ioc_state == MRIOC_STATE_BECOMING_READY ||
-	    ioc_state == MRIOC_STATE_RESET_REQUESTED) {
-		timeout = mrioc->ready_timeout * 10;
-		do {
-			msleep(100);
-		} while (--timeout);
+	mpi3mr_print_ioc_info(mrioc);
 
-		ioc_state = mpi3mr_get_iocstate(mrioc);
-		ioc_info(mrioc,
-		    "IOC in %s state after waiting for reset time\n",
-		    mpi3mr_iocstate_name(ioc_state));
+	retval = mpi3mr_alloc_reply_sense_bufs(mrioc);
+	if (retval) {
+		ioc_err(mrioc,
+		    "%s :Failed to allocated reply sense buffers %d\n",
+		    __func__, retval);
+		goto out_failed_noretry;
 	}
 
-	if (ioc_state == MRIOC_STATE_READY) {
-		retval = mpi3mr_issue_and_process_mur(mrioc,
-		    MPI3MR_RESET_FROM_BRINGUP);
-		if (retval) {
-			ioc_err(mrioc, "Failed to MU reset IOC error %d\n",
-			    retval);
-		}
-		ioc_state = mpi3mr_get_iocstate(mrioc);
+	retval = mpi3mr_alloc_chain_bufs(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "Failed to allocated chain buffers %d\n",
+		    retval);
+		goto out_failed_noretry;
 	}
-	if (ioc_state != MRIOC_STATE_RESET) {
-		mpi3mr_print_fault_info(mrioc);
-		retval = mpi3mr_issue_reset(mrioc,
-		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET,
-		    MPI3MR_RESET_FROM_BRINGUP);
-		if (retval) {
-			ioc_err(mrioc,
-			    "%s :Failed to soft reset IOC error %d\n",
-			    __func__, retval);
-			goto out_failed;
-		}
+
+	retval = mpi3mr_issue_iocinit(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "Failed to Issue IOC Init %d\n",
+		    retval);
+		goto out_failed;
 	}
-	ioc_state = mpi3mr_get_iocstate(mrioc);
-	if (ioc_state != MRIOC_STATE_RESET) {
-		retval = -1;
-		ioc_err(mrioc, "Cannot bring IOC to reset state\n");
+
+	retval = mpi3mr_print_pkg_ver(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "failed to get package version\n");
 		goto out_failed;
 	}
 
-	retval = mpi3mr_setup_admin_qpair(mrioc);
+	retval = mpi3mr_setup_isr(mrioc, 0);
 	if (retval) {
-		ioc_err(mrioc, "Failed to setup admin Qs: error %d\n",
+		ioc_err(mrioc, "Failed to re-setup ISR, error %d\n",
+		    retval);
+		goto out_failed_noretry;
+	}
+
+	retval = mpi3mr_create_op_queues(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "Failed to create OpQueues error %d\n",
 		    retval);
 		goto out_failed;
 	}
 
-	retval = mpi3mr_bring_ioc_ready(mrioc);
+	if (!mrioc->pel_seqnum_virt) {
+		dprint_init(mrioc, "allocating memory for pel_seqnum_virt\n");
+		mrioc->pel_seqnum_sz = sizeof(struct mpi3_pel_seq);
+		mrioc->pel_seqnum_virt = dma_alloc_coherent(&mrioc->pdev->dev,
+		    mrioc->pel_seqnum_sz, &mrioc->pel_seqnum_dma,
+		    GFP_KERNEL);
+		if (!mrioc->pel_seqnum_virt) {
+			retval = -ENOMEM;
+			goto out_failed_noretry;
+		}
+	}
+
+	retval = mpi3mr_enable_events(mrioc);
 	if (retval) {
-		ioc_err(mrioc, "Failed to bring ioc ready: error %d\n",
+		ioc_err(mrioc, "failed to enable events %d\n",
 		    retval);
 		goto out_failed;
 	}
 
-	if (init_type != MPI3MR_IT_RESET) {
+	ioc_info(mrioc, "controller initialization completed successfully\n");
+	return retval;
+out_failed:
+	if (retry < 2) {
+		retry++;
+		ioc_warn(mrioc, "retrying controller initialization, retry_count:%d\n",
+		    retry);
+		mpi3mr_memset_buffers(mrioc);
+		goto retry_init;
+	}
+out_failed_noretry:
+	ioc_err(mrioc, "controller initialization failed\n");
+	mpi3mr_issue_reset(mrioc, MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+	    MPI3MR_RESET_FROM_CTLR_CLEANUP);
+	mrioc->unrecoverable = 1;
+	return retval;
+}
+
+/**
+ * mpi3mr_reinit_ioc - Re-Initialize the controller
+ * @mrioc: Adapter instance reference
+ * @is_resume: Called from resume or reset path
+ *
+ * This the controller re-initialization routine, executed from
+ * the soft reset handler or resume callback. Creates
+ * operational reply queue pairs, allocate required memory for
+ * reply pool, sense buffer pool, issue IOC init request to the
+ * firmware, unmask the events and issue port enable to discover
+ * SAS/SATA/NVMe devices and RAID volumes.
+ *
+ * Return: 0 on success and non-zero on failure.
+ */
+int mpi3mr_reinit_ioc(struct mpi3mr_ioc *mrioc, u8 is_resume)
+{
+	int retval = 0;
+	u8 retry = 0;
+	struct mpi3_ioc_facts_data facts_data;
+
+retry_init:
+	dprint_reset(mrioc, "bringing up the controller to ready state\n");
+	retval = mpi3mr_bring_ioc_ready(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "failed to bring to ready state\n");
+		goto out_failed_noretry;
+	}
+
+	if (is_resume) {
+		dprint_reset(mrioc, "setting up single ISR\n");
 		retval = mpi3mr_setup_isr(mrioc, 1);
 		if (retval) {
-			ioc_err(mrioc, "Failed to setup ISR error %d\n",
-			    retval);
-			goto out_failed;
+			ioc_err(mrioc, "failed to setup ISR\n");
+			goto out_failed_noretry;
 		}
 	} else
 		mpi3mr_ioc_enable_intr(mrioc);
 
+	dprint_reset(mrioc, "getting ioc_facts\n");
 	retval = mpi3mr_issue_iocfacts(mrioc, &facts_data);
 	if (retval) {
-		ioc_err(mrioc, "Failed to Issue IOC Facts %d\n",
-		    retval);
+		ioc_err(mrioc, "failed to get ioc_facts\n");
 		goto out_failed;
 	}
 
-	mpi3mr_process_factsdata(mrioc, &facts_data);
-	if (init_type == MPI3MR_IT_INIT) {
-		retval = mpi3mr_check_reset_dma_mask(mrioc);
-		if (retval) {
-			ioc_err(mrioc, "Resetting dma mask failed %d\n",
-			    retval);
-			goto out_failed;
-		}
+	dprint_reset(mrioc, "validating ioc_facts\n");
+	retval = mpi3mr_revalidate_factsdata(mrioc);
+	if (retval) {
+		ioc_err(mrioc, "failed to revalidate ioc_facts data\n");
+		goto out_failed_noretry;
 	}
 
 	mpi3mr_print_ioc_info(mrioc);
 
-	retval = mpi3mr_alloc_reply_sense_bufs(mrioc);
+	dprint_reset(mrioc, "sending ioc_init\n");
+	retval = mpi3mr_issue_iocinit(mrioc);
 	if (retval) {
-		ioc_err(mrioc,
-		    "%s :Failed to allocated reply sense buffers %d\n",
-		    __func__, retval);
+		ioc_err(mrioc, "failed to send ioc_init\n");
 		goto out_failed;
 	}
 
-	if (init_type == MPI3MR_IT_INIT) {
-		retval = mpi3mr_alloc_chain_bufs(mrioc);
-		if (retval) {
-			ioc_err(mrioc, "Failed to allocated chain buffers %d\n",
-			    retval);
-			goto out_failed;
-		}
-	}
-
-	retval = mpi3mr_issue_iocinit(mrioc);
+	dprint_reset(mrioc, "getting package version\n");
+	retval = mpi3mr_print_pkg_ver(mrioc);
 	if (retval) {
-		ioc_err(mrioc, "Failed to Issue IOC Init %d\n",
-		    retval);
+		ioc_err(mrioc, "failed to get package version\n");
 		goto out_failed;
 	}
-	mrioc->reply_free_queue_host_index = mrioc->num_reply_bufs;
-	writel(mrioc->reply_free_queue_host_index,
-	    &mrioc->sysif_regs->reply_free_host_index);
-
-	mrioc->sbq_host_index = mrioc->num_sense_bufs;
-	writel(mrioc->sbq_host_index,
-	    &mrioc->sysif_regs->sense_buffer_free_host_index);
 
-	if (init_type != MPI3MR_IT_RESET) {
+	if (is_resume) {
+		dprint_reset(mrioc, "setting up multiple ISR\n");
 		retval = mpi3mr_setup_isr(mrioc, 0);
 		if (retval) {
-			ioc_err(mrioc, "Failed to re-setup ISR, error %d\n",
-			    retval);
-			goto out_failed;
+			ioc_err(mrioc, "failed to re-setup ISR\n");
+			goto out_failed_noretry;
 		}
 	}
 
+	dprint_reset(mrioc, "creating operational queue pairs\n");
 	retval = mpi3mr_create_op_queues(mrioc);
 	if (retval) {
-		ioc_err(mrioc, "Failed to create OpQueues error %d\n",
-		    retval);
+		ioc_err(mrioc, "failed to create operational queue pairs\n");
 		goto out_failed;
 	}
 
-	if ((init_type != MPI3MR_IT_INIT) &&
-	    (mrioc->shost->nr_hw_queues > mrioc->num_op_reply_q)) {
-		retval = -1;
+	if (!mrioc->pel_seqnum_virt) {
+		dprint_reset(mrioc, "allocating memory for pel_seqnum_virt\n");
+		mrioc->pel_seqnum_sz = sizeof(struct mpi3_pel_seq);
+		mrioc->pel_seqnum_virt = dma_alloc_coherent(&mrioc->pdev->dev,
+		    mrioc->pel_seqnum_sz, &mrioc->pel_seqnum_dma,
+		    GFP_KERNEL);
+		if (!mrioc->pel_seqnum_virt) {
+			retval = -ENOMEM;
+			goto out_failed_noretry;
+		}
+	}
+
+	if (mrioc->shost->nr_hw_queues > mrioc->num_op_reply_q) {
 		ioc_err(mrioc,
-		    "Cannot create minimum number of OpQueues expected:%d created:%d\n",
+		    "cannot create minimum number of operational queues expected:%d created:%d\n",
 		    mrioc->shost->nr_hw_queues, mrioc->num_op_reply_q);
-		goto out_failed;
+		goto out_failed_noretry;
 	}
 
-	for (i = 0; i < MPI3_EVENT_NOTIFY_EVENTMASK_WORDS; i++)
-		mrioc->event_masks[i] = -1;
-
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_DEVICE_ADDED);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_DEVICE_INFO_CHANGED);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_DEVICE_STATUS_CHANGE);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_ENCL_DEVICE_STATUS_CHANGE);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_TOPOLOGY_CHANGE_LIST);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_DISCOVERY);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_DEVICE_DISCOVERY_ERROR);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_SAS_BROADCAST_PRIMITIVE);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_PCIE_TOPOLOGY_CHANGE_LIST);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_PCIE_ENUMERATION);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_CABLE_MGMT);
-	mpi3mr_unmask_events(mrioc, MPI3_EVENT_ENERGY_PACK_CHANGE);
-
-	retval = mpi3mr_issue_event_notification(mrioc);
+	dprint_reset(mrioc, "enabling events\n");
+	retval = mpi3mr_enable_events(mrioc);
 	if (retval) {
-		ioc_err(mrioc, "Failed to issue event notification %d\n",
-		    retval);
+		ioc_err(mrioc, "failed to enable events\n");
 		goto out_failed;
 	}
 
-	if (init_type != MPI3MR_IT_INIT) {
-		ioc_info(mrioc, "Issuing Port Enable\n");
-		retval = mpi3mr_issue_port_enable(mrioc, 0);
-		if (retval) {
-			ioc_err(mrioc, "Failed to issue port enable %d\n",
-			    retval);
-			goto out_failed;
-		}
+	ioc_info(mrioc, "sending port enable\n");
+	retval = mpi3mr_issue_port_enable(mrioc, 0);
+	if (retval) {
+		ioc_err(mrioc, "failed to issue port enable\n");
+		goto out_failed;
 	}
-	return retval;
 
+	ioc_info(mrioc, "controller %s completed successfully\n",
+	    (is_resume)?"resume":"re-initialization");
+	return retval;
 out_failed:
-	if (init_type == MPI3MR_IT_INIT)
-		mpi3mr_cleanup_ioc(mrioc, MPI3MR_COMPLETE_CLEANUP);
-	else
-		mpi3mr_cleanup_ioc(mrioc, MPI3MR_REINIT_FAILURE);
-out_nocleanup:
+	if (retry < 2) {
+		retry++;
+		ioc_warn(mrioc, "retrying controller %s, retry_count:%d\n",
+		    (is_resume)?"resume":"re-initialization", retry);
+		mpi3mr_memset_buffers(mrioc);
+		goto retry_init;
+	}
+out_failed_noretry:
+	ioc_err(mrioc, "controller %s is failed\n",
+	    (is_resume)?"resume":"re-initialization");
+	mpi3mr_issue_reset(mrioc, MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT,
+	    MPI3MR_RESET_FROM_CTLR_CLEANUP);
+	mrioc->unrecoverable = 1;
 	return retval;
 }
 
@@ -3502,17 +3982,35 @@
 {
 	u16 i;
 
-	memset(mrioc->admin_req_base, 0, mrioc->admin_req_q_sz);
-	memset(mrioc->admin_reply_base, 0, mrioc->admin_reply_q_sz);
-
-	memset(mrioc->init_cmds.reply, 0, sizeof(*mrioc->init_cmds.reply));
-	memset(mrioc->host_tm_cmds.reply, 0,
-	    sizeof(*mrioc->host_tm_cmds.reply));
-	for (i = 0; i < MPI3MR_NUM_DEVRMCMD; i++)
-		memset(mrioc->dev_rmhs_cmds[i].reply, 0,
-		    sizeof(*mrioc->dev_rmhs_cmds[i].reply));
-	memset(mrioc->removepend_bitmap, 0, mrioc->dev_handle_bitmap_sz);
-	memset(mrioc->devrem_bitmap, 0, mrioc->devrem_bitmap_sz);
+	mrioc->change_count = 0;
+	mrioc->active_poll_qcount = 0;
+	mrioc->default_qcount = 0;
+	if (mrioc->admin_req_base)
+		memset(mrioc->admin_req_base, 0, mrioc->admin_req_q_sz);
+	if (mrioc->admin_reply_base)
+		memset(mrioc->admin_reply_base, 0, mrioc->admin_reply_q_sz);
+
+	if (mrioc->init_cmds.reply) {
+		memset(mrioc->init_cmds.reply, 0, sizeof(*mrioc->init_cmds.reply));
+		memset(mrioc->bsg_cmds.reply, 0,
+		    sizeof(*mrioc->bsg_cmds.reply));
+		memset(mrioc->host_tm_cmds.reply, 0,
+		    sizeof(*mrioc->host_tm_cmds.reply));
+		memset(mrioc->pel_cmds.reply, 0,
+		    sizeof(*mrioc->pel_cmds.reply));
+		memset(mrioc->pel_abort_cmd.reply, 0,
+		    sizeof(*mrioc->pel_abort_cmd.reply));
+		for (i = 0; i < MPI3MR_NUM_DEVRMCMD; i++)
+			memset(mrioc->dev_rmhs_cmds[i].reply, 0,
+			    sizeof(*mrioc->dev_rmhs_cmds[i].reply));
+		for (i = 0; i < MPI3MR_NUM_EVTACKCMD; i++)
+			memset(mrioc->evtack_cmds[i].reply, 0,
+			    sizeof(*mrioc->evtack_cmds[i].reply));
+		memset(mrioc->removepend_bitmap, 0, mrioc->dev_handle_bitmap_sz);
+		memset(mrioc->devrem_bitmap, 0, mrioc->devrem_bitmap_sz);
+		memset(mrioc->evtack_cmds_bitmap, 0,
+		    mrioc->evtack_cmds_bitmap_sz);
+	}
 
 	for (i = 0; i < mrioc->num_queues; i++) {
 		mrioc->op_reply_qinfo[i].qid = 0;
@@ -3541,7 +4039,7 @@
  *
  * Return: Nothing.
  */
-static void mpi3mr_free_mem(struct mpi3mr_ioc *mrioc)
+void mpi3mr_free_mem(struct mpi3mr_ioc *mrioc)
 {
 	u16 i;
 	struct mpi3mr_intr_info *intr_info;
@@ -3602,15 +4100,32 @@
 	kfree(mrioc->init_cmds.reply);
 	mrioc->init_cmds.reply = NULL;
 
+	kfree(mrioc->bsg_cmds.reply);
+	mrioc->bsg_cmds.reply = NULL;
+
 	kfree(mrioc->host_tm_cmds.reply);
 	mrioc->host_tm_cmds.reply = NULL;
 
+	kfree(mrioc->pel_cmds.reply);
+	mrioc->pel_cmds.reply = NULL;
+
+	kfree(mrioc->pel_abort_cmd.reply);
+	mrioc->pel_abort_cmd.reply = NULL;
+
+	for (i = 0; i < MPI3MR_NUM_EVTACKCMD; i++) {
+		kfree(mrioc->evtack_cmds[i].reply);
+		mrioc->evtack_cmds[i].reply = NULL;
+	}
+
 	kfree(mrioc->removepend_bitmap);
 	mrioc->removepend_bitmap = NULL;
 
 	kfree(mrioc->devrem_bitmap);
 	mrioc->devrem_bitmap = NULL;
 
+	kfree(mrioc->evtack_cmds_bitmap);
+	mrioc->evtack_cmds_bitmap = NULL;
+
 	kfree(mrioc->chain_bitmap);
 	mrioc->chain_bitmap = NULL;
 
@@ -3645,6 +4160,16 @@
 		    mrioc->admin_req_base, mrioc->admin_req_dma);
 		mrioc->admin_req_base = NULL;
 	}
+
+	if (mrioc->pel_seqnum_virt) {
+		dma_free_coherent(&mrioc->pdev->dev, mrioc->pel_seqnum_sz,
+		    mrioc->pel_seqnum_virt, mrioc->pel_seqnum_dma);
+		mrioc->pel_seqnum_virt = NULL;
+	}
+
+	kfree(mrioc->logdata_buf);
+	mrioc->logdata_buf = NULL;
+
 }
 
 /**
@@ -3677,7 +4202,7 @@
 
 	ioc_config = readl(&mrioc->sysif_regs->ioc_configuration);
 	ioc_config |= MPI3_SYSIF_IOC_CONFIG_SHUTDOWN_NORMAL;
-	ioc_config |= MPI3_SYSIF_IOC_CONFIG_DEVICE_SHUTDOWN;
+	ioc_config |= MPI3_SYSIF_IOC_CONFIG_DEVICE_SHUTDOWN_SEND_REQ;
 
 	writel(ioc_config, &mrioc->sysif_regs->ioc_configuration);
 
@@ -3713,21 +4238,17 @@
 /**
  * mpi3mr_cleanup_ioc - Cleanup controller
  * @mrioc: Adapter instance reference
- * @reason: Cleanup reason
  *
  * controller cleanup handler, Message unit reset or soft reset
- * and shutdown notification is issued to the controller and the
- * associated memory resources are freed.
+ * and shutdown notification is issued to the controller.
  *
  * Return: Nothing.
  */
-void mpi3mr_cleanup_ioc(struct mpi3mr_ioc *mrioc, u8 reason)
+void mpi3mr_cleanup_ioc(struct mpi3mr_ioc *mrioc)
 {
 	enum mpi3mr_iocstate ioc_state;
 
-	if (reason == MPI3MR_COMPLETE_CLEANUP)
-		mpi3mr_stop_watchdog(mrioc);
-
+	dprint_exit(mrioc, "cleaning up the controller\n");
 	mpi3mr_ioc_disable_intr(mrioc);
 
 	ioc_state = mpi3mr_get_iocstate(mrioc);
@@ -3739,15 +4260,9 @@
 			mpi3mr_issue_reset(mrioc,
 			    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_SOFT_RESET,
 			    MPI3MR_RESET_FROM_MUR_FAILURE);
-
-		if (reason != MPI3MR_REINIT_FAILURE)
-			mpi3mr_issue_ioc_shutdown(mrioc);
-	}
-
-	if (reason == MPI3MR_COMPLETE_CLEANUP) {
-		mpi3mr_free_mem(mrioc);
-		mpi3mr_cleanup_resources(mrioc);
+		mpi3mr_issue_ioc_shutdown(mrioc);
 	}
+	dprint_exit(mrioc, "controller cleanup completed\n");
 }
 
 /**
@@ -3789,6 +4304,8 @@
 
 	cmdptr = &mrioc->init_cmds;
 	mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
+	cmdptr = &mrioc->bsg_cmds;
+	mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
 	cmdptr = &mrioc->host_tm_cmds;
 	mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
 
@@ -3796,44 +4313,262 @@
 		cmdptr = &mrioc->dev_rmhs_cmds[i];
 		mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
 	}
+
+	for (i = 0; i < MPI3MR_NUM_EVTACKCMD; i++) {
+		cmdptr = &mrioc->evtack_cmds[i];
+		mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
+	}
+
+	cmdptr = &mrioc->pel_cmds;
+	mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
+
+	cmdptr = &mrioc->pel_abort_cmd;
+	mpi3mr_drv_cmd_comp_reset(mrioc, cmdptr);
+
 }
 
 /**
- * mpi3mr_diagfault_reset_handler - Diag fault reset handler
+ * mpi3mr_pel_wait_post - Issue PEL Wait
  * @mrioc: Adapter instance reference
- * @reset_reason: Reset reason code
+ * @drv_cmd: Internal command tracker
  *
- * This is an handler for issuing diag fault reset from the
- * applications through IOCTL path to stop the execution of the
- * controller
+ * Issue PEL Wait MPI request through admin queue and return.
  *
- * Return: 0 on success, non-zero on failure.
+ * Return: Nothing.
  */
-int mpi3mr_diagfault_reset_handler(struct mpi3mr_ioc *mrioc,
-	u32 reset_reason)
+static void mpi3mr_pel_wait_post(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd)
 {
-	int retval = 0;
+	struct mpi3_pel_req_action_wait pel_wait;
 
-	ioc_info(mrioc, "Entry: reason code: %s\n",
-	    mpi3mr_reset_rc_name(reset_reason));
-	mrioc->reset_in_progress = 1;
+	mrioc->pel_abort_requested = false;
 
-	mpi3mr_ioc_disable_intr(mrioc);
+	memset(&pel_wait, 0, sizeof(pel_wait));
+	drv_cmd->state = MPI3MR_CMD_PENDING;
+	drv_cmd->is_waiting = 0;
+	drv_cmd->callback = mpi3mr_pel_wait_complete;
+	drv_cmd->ioc_status = 0;
+	drv_cmd->ioc_loginfo = 0;
+	pel_wait.host_tag = cpu_to_le16(MPI3MR_HOSTTAG_PEL_WAIT);
+	pel_wait.function = MPI3_FUNCTION_PERSISTENT_EVENT_LOG;
+	pel_wait.action = MPI3_PEL_ACTION_WAIT;
+	pel_wait.starting_sequence_number = cpu_to_le32(mrioc->pel_newest_seqnum);
+	pel_wait.locale = cpu_to_le16(mrioc->pel_locale);
+	pel_wait.class = cpu_to_le16(mrioc->pel_class);
+	pel_wait.wait_time = MPI3_PEL_WAITTIME_INFINITE_WAIT;
+	dprint_bsg_info(mrioc, "sending pel_wait seqnum(%d), class(%d), locale(0x%08x)\n",
+	    mrioc->pel_newest_seqnum, mrioc->pel_class, mrioc->pel_locale);
+
+	if (mpi3mr_admin_request_post(mrioc, &pel_wait, sizeof(pel_wait), 0)) {
+		dprint_bsg_err(mrioc,
+			    "Issuing PELWait: Admin post failed\n");
+		drv_cmd->state = MPI3MR_CMD_NOTUSED;
+		drv_cmd->callback = NULL;
+		drv_cmd->retry_count = 0;
+		mrioc->pel_enabled = false;
+	}
+}
 
-	retval = mpi3mr_issue_reset(mrioc,
-	    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT, reset_reason);
+/**
+ * mpi3mr_pel_get_seqnum_post - Issue PEL Get Sequence number
+ * @mrioc: Adapter instance reference
+ * @drv_cmd: Internal command tracker
+ *
+ * Issue PEL get sequence number MPI request through admin queue
+ * and return.
+ *
+ * Return: 0 on success, non-zero on failure.
+ */
+int mpi3mr_pel_get_seqnum_post(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd)
+{
+	struct mpi3_pel_req_action_get_sequence_numbers pel_getseq_req;
+	u8 sgl_flags = MPI3MR_SGEFLAGS_SYSTEM_SIMPLE_END_OF_LIST;
+	int retval = 0;
 
+	memset(&pel_getseq_req, 0, sizeof(pel_getseq_req));
+	mrioc->pel_cmds.state = MPI3MR_CMD_PENDING;
+	mrioc->pel_cmds.is_waiting = 0;
+	mrioc->pel_cmds.ioc_status = 0;
+	mrioc->pel_cmds.ioc_loginfo = 0;
+	mrioc->pel_cmds.callback = mpi3mr_pel_get_seqnum_complete;
+	pel_getseq_req.host_tag = cpu_to_le16(MPI3MR_HOSTTAG_PEL_WAIT);
+	pel_getseq_req.function = MPI3_FUNCTION_PERSISTENT_EVENT_LOG;
+	pel_getseq_req.action = MPI3_PEL_ACTION_GET_SEQNUM;
+	mpi3mr_add_sg_single(&pel_getseq_req.sgl, sgl_flags,
+	    mrioc->pel_seqnum_sz, mrioc->pel_seqnum_dma);
+
+	retval = mpi3mr_admin_request_post(mrioc, &pel_getseq_req,
+			sizeof(pel_getseq_req), 0);
 	if (retval) {
-		ioc_err(mrioc, "The diag fault reset failed: reason %d\n",
-		    reset_reason);
-		mpi3mr_ioc_enable_intr(mrioc);
+		if (drv_cmd) {
+			drv_cmd->state = MPI3MR_CMD_NOTUSED;
+			drv_cmd->callback = NULL;
+			drv_cmd->retry_count = 0;
+		}
+		mrioc->pel_enabled = false;
 	}
-	ioc_info(mrioc, "%s\n", ((retval == 0) ? "SUCCESS" : "FAILED"));
-	mrioc->reset_in_progress = 0;
+
 	return retval;
 }
 
 /**
+ * mpi3mr_pel_wait_complete - PELWait Completion callback
+ * @mrioc: Adapter instance reference
+ * @drv_cmd: Internal command tracker
+ *
+ * This is a callback handler for the PELWait request and
+ * firmware completes a PELWait request when it is aborted or a
+ * new PEL entry is available. This sends AEN to the application
+ * and if the PELwait completion is not due to PELAbort then
+ * this will send a request for new PEL Sequence number
+ *
+ * Return: Nothing.
+ */
+static void mpi3mr_pel_wait_complete(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd)
+{
+	struct mpi3_pel_reply *pel_reply = NULL;
+	u16 ioc_status, pe_log_status;
+	bool do_retry = false;
+
+	if (drv_cmd->state & MPI3MR_CMD_RESET)
+		goto cleanup_drv_cmd;
+
+	ioc_status = drv_cmd->ioc_status & MPI3_IOCSTATUS_STATUS_MASK;
+	if (ioc_status != MPI3_IOCSTATUS_SUCCESS) {
+		ioc_err(mrioc, "%s: Failed ioc_status(0x%04x) Loginfo(0x%08x)\n",
+			__func__, ioc_status, drv_cmd->ioc_loginfo);
+		dprint_bsg_err(mrioc,
+		    "pel_wait: failed with ioc_status(0x%04x), log_info(0x%08x)\n",
+		    ioc_status, drv_cmd->ioc_loginfo);
+		do_retry = true;
+	}
+
+	if (drv_cmd->state & MPI3MR_CMD_REPLY_VALID)
+		pel_reply = (struct mpi3_pel_reply *)drv_cmd->reply;
+
+	if (!pel_reply) {
+		dprint_bsg_err(mrioc,
+		    "pel_wait: failed due to no reply\n");
+		goto out_failed;
+	}
+
+	pe_log_status = le16_to_cpu(pel_reply->pe_log_status);
+	if ((pe_log_status != MPI3_PEL_STATUS_SUCCESS) &&
+	    (pe_log_status != MPI3_PEL_STATUS_ABORTED)) {
+		ioc_err(mrioc, "%s: Failed pe_log_status(0x%04x)\n",
+			__func__, pe_log_status);
+		dprint_bsg_err(mrioc,
+		    "pel_wait: failed due to pel_log_status(0x%04x)\n",
+		    pe_log_status);
+		do_retry = true;
+	}
+
+	if (do_retry) {
+		if (drv_cmd->retry_count < MPI3MR_PEL_RETRY_COUNT) {
+			drv_cmd->retry_count++;
+			dprint_bsg_err(mrioc, "pel_wait: retrying(%d)\n",
+			    drv_cmd->retry_count);
+			mpi3mr_pel_wait_post(mrioc, drv_cmd);
+			return;
+		}
+		dprint_bsg_err(mrioc,
+		    "pel_wait: failed after all retries(%d)\n",
+		    drv_cmd->retry_count);
+		goto out_failed;
+	}
+	atomic64_inc(&event_counter);
+	if (!mrioc->pel_abort_requested) {
+		mrioc->pel_cmds.retry_count = 0;
+		mpi3mr_pel_get_seqnum_post(mrioc, &mrioc->pel_cmds);
+	}
+
+	return;
+out_failed:
+	mrioc->pel_enabled = false;
+cleanup_drv_cmd:
+	drv_cmd->state = MPI3MR_CMD_NOTUSED;
+	drv_cmd->callback = NULL;
+	drv_cmd->retry_count = 0;
+}
+
+/**
+ * mpi3mr_pel_get_seqnum_complete - PELGetSeqNum Completion callback
+ * @mrioc: Adapter instance reference
+ * @drv_cmd: Internal command tracker
+ *
+ * This is a callback handler for the PEL get sequence number
+ * request and a new PEL wait request will be issued to the
+ * firmware from this
+ *
+ * Return: Nothing.
+ */
+void mpi3mr_pel_get_seqnum_complete(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd)
+{
+	struct mpi3_pel_reply *pel_reply = NULL;
+	struct mpi3_pel_seq *pel_seqnum_virt;
+	u16 ioc_status;
+	bool do_retry = false;
+
+	pel_seqnum_virt = (struct mpi3_pel_seq *)mrioc->pel_seqnum_virt;
+
+	if (drv_cmd->state & MPI3MR_CMD_RESET)
+		goto cleanup_drv_cmd;
+
+	ioc_status = drv_cmd->ioc_status & MPI3_IOCSTATUS_STATUS_MASK;
+	if (ioc_status != MPI3_IOCSTATUS_SUCCESS) {
+		dprint_bsg_err(mrioc,
+		    "pel_get_seqnum: failed with ioc_status(0x%04x), log_info(0x%08x)\n",
+		    ioc_status, drv_cmd->ioc_loginfo);
+		do_retry = true;
+	}
+
+	if (drv_cmd->state & MPI3MR_CMD_REPLY_VALID)
+		pel_reply = (struct mpi3_pel_reply *)drv_cmd->reply;
+	if (!pel_reply) {
+		dprint_bsg_err(mrioc,
+		    "pel_get_seqnum: failed due to no reply\n");
+		goto out_failed;
+	}
+
+	if (le16_to_cpu(pel_reply->pe_log_status) != MPI3_PEL_STATUS_SUCCESS) {
+		dprint_bsg_err(mrioc,
+		    "pel_get_seqnum: failed due to pel_log_status(0x%04x)\n",
+		    le16_to_cpu(pel_reply->pe_log_status));
+		do_retry = true;
+	}
+
+	if (do_retry) {
+		if (drv_cmd->retry_count < MPI3MR_PEL_RETRY_COUNT) {
+			drv_cmd->retry_count++;
+			dprint_bsg_err(mrioc,
+			    "pel_get_seqnum: retrying(%d)\n",
+			    drv_cmd->retry_count);
+			mpi3mr_pel_get_seqnum_post(mrioc, drv_cmd);
+			return;
+		}
+
+		dprint_bsg_err(mrioc,
+		    "pel_get_seqnum: failed after all retries(%d)\n",
+		    drv_cmd->retry_count);
+		goto out_failed;
+	}
+	mrioc->pel_newest_seqnum = le32_to_cpu(pel_seqnum_virt->newest) + 1;
+	drv_cmd->retry_count = 0;
+	mpi3mr_pel_wait_post(mrioc, drv_cmd);
+
+	return;
+out_failed:
+	mrioc->pel_enabled = false;
+cleanup_drv_cmd:
+	drv_cmd->state = MPI3MR_CMD_NOTUSED;
+	drv_cmd->callback = NULL;
+	drv_cmd->retry_count = 0;
+}
+
+/**
  * mpi3mr_soft_reset_handler - Reset the controller
  * @mrioc: Adapter instance reference
  * @reset_reason: Reset reason code
@@ -3842,7 +4577,7 @@
  * This is an handler for recovering controller by issuing soft
  * reset are diag fault reset.  This is a blocking function and
  * when one reset is executed if any other resets they will be
- * blocked. All IOCTLs/IO will be blocked during the reset. If
+ * blocked. All BSG requests will be blocked during the reset. If
  * controller reset is successful then the controller will be
  * reinitalized, otherwise the controller will be marked as not
  * recoverable
@@ -3861,34 +4596,45 @@
 	unsigned long flags;
 	u32 host_diagnostic, timeout = MPI3_SYSIF_DIAG_SAVE_TIMEOUT * 10;
 
-	if (mrioc->fault_dbg) {
-		if (snapdump)
-			mpi3mr_set_diagsave(mrioc);
-		mpi3mr_kill_ioc(mrioc, reset_reason);
-	}
-
+	/* Block the reset handler until diag save in progress*/
+	dprint_reset(mrioc,
+	    "soft_reset_handler: check and block on diagsave_timeout(%d)\n",
+	    mrioc->diagsave_timeout);
+	while (mrioc->diagsave_timeout)
+		ssleep(1);
 	/*
 	 * Block new resets until the currently executing one is finished and
 	 * return the status of the existing reset for all blocked resets
 	 */
+	dprint_reset(mrioc, "soft_reset_handler: acquiring reset_mutex\n");
 	if (!mutex_trylock(&mrioc->reset_mutex)) {
-		ioc_info(mrioc, "Another reset in progress\n");
-		return -1;
+		ioc_info(mrioc,
+		    "controller reset triggered by %s is blocked due to another reset in progress\n",
+		    mpi3mr_reset_rc_name(reset_reason));
+		do {
+			ssleep(1);
+		} while (mrioc->reset_in_progress == 1);
+		ioc_info(mrioc,
+		    "returning previous reset result(%d) for the reset triggered by %s\n",
+		    mrioc->prev_reset_result,
+		    mpi3mr_reset_rc_name(reset_reason));
+		return mrioc->prev_reset_result;
 	}
+	ioc_info(mrioc, "controller reset is triggered by %s\n",
+	    mpi3mr_reset_rc_name(reset_reason));
+
 	mrioc->reset_in_progress = 1;
+	mrioc->stop_bsgs = 1;
+	mrioc->prev_reset_result = -1;
 
 	if ((!snapdump) && (reset_reason != MPI3MR_RESET_FROM_FAULT_WATCH) &&
+	    (reset_reason != MPI3MR_RESET_FROM_FIRMWARE) &&
 	    (reset_reason != MPI3MR_RESET_FROM_CIACTIV_FAULT)) {
 		for (i = 0; i < MPI3_EVENT_NOTIFY_EVENTMASK_WORDS; i++)
 			mrioc->event_masks[i] = -1;
 
-		retval = mpi3mr_issue_event_notification(mrioc);
-
-		if (retval) {
-			ioc_err(mrioc,
-			    "Failed to turn off events prior to reset %d\n",
-			    retval);
-		}
+		dprint_reset(mrioc, "soft_reset_handler: masking events\n");
+		mpi3mr_issue_event_notification(mrioc);
 	}
 
 	mpi3mr_wait_for_host_io(mrioc, MPI3MR_RESET_HOST_IOWAIT_TIMEOUT);
@@ -3918,15 +4664,20 @@
 		goto out;
 	}
 
-	mpi3mr_flush_delayed_rmhs_list(mrioc);
+	mpi3mr_flush_delayed_cmd_lists(mrioc);
 	mpi3mr_flush_drv_cmds(mrioc);
 	memset(mrioc->devrem_bitmap, 0, mrioc->devrem_bitmap_sz);
 	memset(mrioc->removepend_bitmap, 0, mrioc->dev_handle_bitmap_sz);
-	mpi3mr_cleanup_fwevt_list(mrioc);
+	memset(mrioc->evtack_cmds_bitmap, 0, mrioc->evtack_cmds_bitmap_sz);
 	mpi3mr_flush_host_io(mrioc);
+	mpi3mr_cleanup_fwevt_list(mrioc);
 	mpi3mr_invalidate_devhandles(mrioc);
+	if (mrioc->prepare_for_reset) {
+		mrioc->prepare_for_reset = 0;
+		mrioc->prepare_for_reset_timeout_counter = 0;
+	}
 	mpi3mr_memset_buffers(mrioc);
-	retval = mpi3mr_init_ioc(mrioc, MPI3MR_IT_RESET);
+	retval = mpi3mr_reinit_ioc(mrioc, 0);
 	if (retval) {
 		pr_err(IOCNAME "reinit after soft reset failed: reason %d\n",
 		    mrioc->name, reset_reason);
@@ -3936,8 +4687,14 @@
 
 out:
 	if (!retval) {
+		mrioc->diagsave_timeout = 0;
 		mrioc->reset_in_progress = 0;
-		scsi_unblock_requests(mrioc->shost);
+		mrioc->pel_abort_requested = 0;
+		if (mrioc->pel_enabled) {
+			mrioc->pel_cmds.retry_count = 0;
+			mpi3mr_pel_wait_post(mrioc, &mrioc->pel_cmds);
+		}
+
 		mpi3mr_rfresh_tgtdevs(mrioc);
 		mrioc->ts_update_counter = 0;
 		spin_lock_irqsave(&mrioc->watchdog_lock, flags);
@@ -3946,6 +4703,9 @@
 			    &mrioc->watchdog_work,
 			    msecs_to_jiffies(MPI3MR_WATCHDOG_INTERVAL));
 		spin_unlock_irqrestore(&mrioc->watchdog_lock, flags);
+		mrioc->stop_bsgs = 0;
+		if (mrioc->pel_enabled)
+			atomic64_inc(&event_counter);
 	} else {
 		mpi3mr_issue_reset(mrioc,
 		    MPI3_SYSIF_HOST_DIAG_RESET_ACTION_DIAG_FAULT, reset_reason);
@@ -3953,8 +4713,9 @@
 		mrioc->reset_in_progress = 0;
 		retval = -1;
 	}
-
+	mrioc->prev_reset_result = retval;
 	mutex_unlock(&mrioc->reset_mutex);
-	ioc_info(mrioc, "%s\n", ((retval == 0) ? "SUCCESS" : "FAILED"));
+	ioc_info(mrioc, "controller reset is %s\n",
+	    ((retval == 0) ? "successful" : "failed"));
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpi3mr/mpi3mr_os.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpi3mr/mpi3mr_os.c
@@ -2,7 +2,7 @@
 /*
  * Driver for Broadcom MPI3 Storage Controllers
  *
- * Copyright (C) 2017-2021 Broadcom Inc.
+ * Copyright (C) 2017-2022 Broadcom Inc.
  *  (mailto: mpi3mr-linuxdrv.pdl@broadcom.com)
  *
  */
@@ -14,6 +14,7 @@
 DEFINE_SPINLOCK(mrioc_list_lock);
 static int mrioc_ids;
 static int warn_non_secure_ctlr;
+atomic64_t event_counter;
 
 MODULE_AUTHOR(MPI3MR_DRIVER_AUTHOR);
 MODULE_DESCRIPTION(MPI3MR_DRIVER_DESC);
@@ -34,6 +35,9 @@
 	" bits for enabling additional logging info (default=0)");
 
 /* Forward declarations*/
+static void mpi3mr_send_event_ack(struct mpi3mr_ioc *mrioc, u8 event,
+	struct mpi3mr_drv_cmd *cmdparam, u32 event_ctx);
+
 /**
  * mpi3mr_host_tag_for_scmd - Get host tag for a scmd
  * @mrioc: Adapter instance reference
@@ -283,6 +287,35 @@
 }
 
 /**
+ * mpi3mr_cancel_work - cancel firmware event
+ * @fwevt: fwevt object which needs to be canceled
+ *
+ * Return: Nothing.
+ */
+static void mpi3mr_cancel_work(struct mpi3mr_fwevt *fwevt)
+{
+	/*
+	 * Wait on the fwevt to complete. If this returns 1, then
+	 * the event was never executed.
+	 *
+	 * If it did execute, we wait for it to finish, and the put will
+	 * happen from mpi3mr_process_fwevt()
+	 */
+	if (cancel_work_sync(&fwevt->work)) {
+		/*
+		 * Put fwevt reference count after
+		 * dequeuing it from worker queue
+		 */
+		mpi3mr_fwevt_put(fwevt);
+		/*
+		 * Put fwevt reference count to neutralize
+		 * kref_init increment
+		 */
+		mpi3mr_fwevt_put(fwevt);
+	}
+}
+
+/**
  * mpi3mr_cleanup_fwevt_list - Cleanup firmware event list
  * @mrioc: Adapter instance reference
  *
@@ -299,28 +332,25 @@
 	    !mrioc->fwevt_worker_thread)
 		return;
 
-	while ((fwevt = mpi3mr_dequeue_fwevt(mrioc)) ||
-	    (fwevt = mrioc->current_event)) {
+	while ((fwevt = mpi3mr_dequeue_fwevt(mrioc)))
+		mpi3mr_cancel_work(fwevt);
+
+	if (mrioc->current_event) {
+		fwevt = mrioc->current_event;
 		/*
-		 * Wait on the fwevt to complete. If this returns 1, then
-		 * the event was never executed, and we need a put for the
-		 * reference the work had on the fwevt.
-		 *
-		 * If it did execute, we wait for it to finish, and the put will
-		 * happen from mpi3mr_process_fwevt()
+		 * Don't call cancel_work_sync() API for the
+		 * fwevt work if the controller reset is
+		 * get called as part of processing the
+		 * same fwevt work (or) when worker thread is
+		 * waiting for device add/remove APIs to complete.
+		 * Otherwise we will see deadlock.
 		 */
-		if (cancel_work_sync(&fwevt->work)) {
-			/*
-			 * Put fwevt reference count after
-			 * dequeuing it from worker queue
-			 */
-			mpi3mr_fwevt_put(fwevt);
-			/*
-			 * Put fwevt reference count to neutralize
-			 * kref_init increment
-			 */
-			mpi3mr_fwevt_put(fwevt);
+		if (current_work() == &fwevt->work || fwevt->pending_at_sml) {
+			fwevt->discard = 1;
+			return;
 		}
+
+		mpi3mr_cancel_work(fwevt);
 	}
 }
 
@@ -418,6 +448,74 @@
 }
 
 /**
+ * mpi3mr_count_dev_pending - Count commands pending for a lun
+ * @rq: Block request
+ * @data: SCSI device reference
+ * @reserved: Unused
+ *
+ * This is an iterator function called for each SCSI command in
+ * a host and if the command is pending in the LLD for the
+ * specific device(lun) then device specific pending I/O counter
+ * is updated in the device structure.
+ *
+ * Return: true always.
+ */
+
+static bool mpi3mr_count_dev_pending(struct request *rq,
+	void *data, bool reserved)
+{
+	struct scsi_device *sdev = (struct scsi_device *)data;
+	struct mpi3mr_sdev_priv_data *sdev_priv_data = sdev->hostdata;
+	struct scsi_cmnd *scmd = blk_mq_rq_to_pdu(rq);
+	struct scmd_priv *priv;
+
+	if (scmd) {
+		priv = scsi_cmd_priv(scmd);
+		if (!priv->in_lld_scope)
+			goto out;
+		if (scmd->device == sdev)
+			sdev_priv_data->pend_count++;
+	}
+
+out:
+	return true;
+}
+
+/**
+ * mpi3mr_count_tgt_pending - Count commands pending for target
+ * @rq: Block request
+ * @data: SCSI target reference
+ * @reserved: Unused
+ *
+ * This is an iterator function called for each SCSI command in
+ * a host and if the command is pending in the LLD for the
+ * specific target then target specific pending I/O counter is
+ * updated in the target structure.
+ *
+ * Return: true always.
+ */
+
+static bool mpi3mr_count_tgt_pending(struct request *rq,
+	void *data, bool reserved)
+{
+	struct scsi_target *starget = (struct scsi_target *)data;
+	struct mpi3mr_stgt_priv_data *stgt_priv_data = starget->hostdata;
+	struct scsi_cmnd *scmd = blk_mq_rq_to_pdu(rq);
+	struct scmd_priv *priv;
+
+	if (scmd) {
+		priv = scsi_cmd_priv(scmd);
+		if (!priv->in_lld_scope)
+			goto out;
+		if (scmd->device && (scsi_target(scmd->device) == starget))
+			stgt_priv_data->pend_count++;
+	}
+
+out:
+	return true;
+}
+
+/**
  * mpi3mr_flush_host_io -  Flush host I/Os
  * @mrioc: Adapter instance reference
  *
@@ -537,7 +635,7 @@
  *
  * Return: Target device reference.
  */
-static struct mpi3mr_tgt_dev *mpi3mr_get_tgtdev_by_handle(
+struct mpi3mr_tgt_dev *mpi3mr_get_tgtdev_by_handle(
 	struct mpi3mr_ioc *mrioc, u16 handle)
 {
 	struct mpi3mr_tgt_dev *tgtdev;
@@ -620,6 +718,24 @@
 }
 
 /**
+ * mpi3mr_print_device_event_notice - print notice related to post processing of
+ *					device event after controller reset.
+ *
+ * @mrioc: Adapter instance reference
+ * @device_add: true for device add event and false for device removal event
+ *
+ * Return: None.
+ */
+static void mpi3mr_print_device_event_notice(struct mpi3mr_ioc *mrioc,
+	bool device_add)
+{
+	ioc_notice(mrioc, "Device %s was in progress before the reset and\n",
+	    (device_add ? "addition" : "removal"));
+	ioc_notice(mrioc, "completed after reset, verify whether the exposed devices\n");
+	ioc_notice(mrioc, "are matched with attached devices for correctness\n");
+}
+
+/**
  * mpi3mr_remove_tgtdev_from_host - Remove dev from upper layers
  * @mrioc: Adapter instance reference
  * @tgtdev: Target device structure
@@ -643,8 +759,17 @@
 	}
 
 	if (tgtdev->starget) {
+		if (mrioc->current_event)
+			mrioc->current_event->pending_at_sml = 1;
 		scsi_remove_target(&tgtdev->starget->dev);
 		tgtdev->host_exposed = 0;
+		if (mrioc->current_event) {
+			mrioc->current_event->pending_at_sml = 0;
+			if (mrioc->current_event->discard) {
+				mpi3mr_print_device_event_notice(mrioc, false);
+				return;
+			}
+		}
 	}
 	ioc_info(mrioc, "%s :Removed handle(0x%04x), wwid(0x%016llx)\n",
 	    __func__, tgtdev->dev_handle, (unsigned long long)tgtdev->wwid);
@@ -678,11 +803,20 @@
 	}
 	if (!tgtdev->host_exposed && !mrioc->reset_in_progress) {
 		tgtdev->host_exposed = 1;
+		if (mrioc->current_event)
+			mrioc->current_event->pending_at_sml = 1;
 		scsi_scan_target(&mrioc->shost->shost_gendev, 0,
 		    tgtdev->perst_id,
 		    SCAN_WILD_CARD, SCSI_SCAN_INITIAL);
 		if (!tgtdev->starget)
 			tgtdev->host_exposed = 0;
+		if (mrioc->current_event) {
+			mrioc->current_event->pending_at_sml = 0;
+			if (mrioc->current_event->discard) {
+				mpi3mr_print_device_event_notice(mrioc, true);
+				goto out;
+			}
+		}
 	}
 out:
 	if (tgtdev)
@@ -742,11 +876,18 @@
 	switch (tgtdev->dev_type) {
 	case MPI3_DEVICE_DEVFORM_PCIE:
 		/*The block layer hw sector size = 512*/
-		blk_queue_max_hw_sectors(sdev->request_queue,
-		    tgtdev->dev_spec.pcie_inf.mdts / 512);
-		blk_queue_virt_boundary(sdev->request_queue,
-		    ((1 << tgtdev->dev_spec.pcie_inf.pgsz) - 1));
-
+		if ((tgtdev->dev_spec.pcie_inf.dev_info &
+		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK) ==
+		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_NVME_DEVICE) {
+			blk_queue_max_hw_sectors(sdev->request_queue,
+			    tgtdev->dev_spec.pcie_inf.mdts / 512);
+			if (tgtdev->dev_spec.pcie_inf.pgsz == 0)
+				blk_queue_virt_boundary(sdev->request_queue,
+				    ((1 << MPI3MR_DEFAULT_PGSZEXP) - 1));
+			else
+				blk_queue_virt_boundary(sdev->request_queue,
+				    ((1 << tgtdev->dev_spec.pcie_inf.pgsz) - 1));
+		}
 		break;
 	default:
 		break;
@@ -770,9 +911,11 @@
 
 	list_for_each_entry_safe(tgtdev, tgtdev_next, &mrioc->tgtdev_list,
 	    list) {
-		if ((tgtdev->dev_handle == MPI3MR_INVALID_DEV_HANDLE) &&
-		    tgtdev->host_exposed) {
-			mpi3mr_remove_tgtdev_from_host(mrioc, tgtdev);
+		if (tgtdev->dev_handle == MPI3MR_INVALID_DEV_HANDLE) {
+			dprint_reset(mrioc, "removing target device with perst_id(%d)\n",
+			    tgtdev->perst_id);
+			if (tgtdev->host_exposed)
+				mpi3mr_remove_tgtdev_from_host(mrioc, tgtdev);
 			mpi3mr_tgtdev_del_from_list(mrioc, tgtdev);
 			mpi3mr_tgtdev_put(tgtdev);
 		}
@@ -781,8 +924,14 @@
 	tgtdev = NULL;
 	list_for_each_entry(tgtdev, &mrioc->tgtdev_list, list) {
 		if ((tgtdev->dev_handle != MPI3MR_INVALID_DEV_HANDLE) &&
-		    !tgtdev->is_hidden && !tgtdev->host_exposed)
-			mpi3mr_report_tgtdev_to_host(mrioc, tgtdev->perst_id);
+		    !tgtdev->is_hidden) {
+			if (!tgtdev->host_exposed)
+				mpi3mr_report_tgtdev_to_host(mrioc,
+							     tgtdev->perst_id);
+			else if (tgtdev->starget)
+				starget_for_each_device(tgtdev->starget,
+							(void *)tgtdev, mpi3mr_update_sdev);
+	}
 	}
 }
 
@@ -824,6 +973,17 @@
 		scsi_tgt_priv_data->dev_type = tgtdev->dev_type;
 	}
 
+	switch (dev_pg0->access_status) {
+	case MPI3_DEVICE0_ASTATUS_NO_ERRORS:
+	case MPI3_DEVICE0_ASTATUS_PREPARE:
+	case MPI3_DEVICE0_ASTATUS_NEEDS_INITIALIZATION:
+	case MPI3_DEVICE0_ASTATUS_DEVICE_MISSING_DELAY:
+		break;
+	default:
+		tgtdev->is_hidden = 1;
+		break;
+	}
+
 	switch (tgtdev->dev_type) {
 	case MPI3_DEVICE_DEVFORM_SAS_SATA:
 	{
@@ -848,6 +1008,7 @@
 		    &dev_pg0->device_specific.pcie_format;
 		u16 dev_info = le16_to_cpu(pcieinf->device_info);
 
+		tgtdev->dev_spec.pcie_inf.dev_info = dev_info;
 		tgtdev->dev_spec.pcie_inf.capb =
 		    le32_to_cpu(pcieinf->capabilities);
 		tgtdev->dev_spec.pcie_inf.mdts = MPI3MR_DEFAULT_MDTS;
@@ -858,14 +1019,18 @@
 			    le32_to_cpu(pcieinf->maximum_data_transfer_size);
 			tgtdev->dev_spec.pcie_inf.pgsz = pcieinf->page_size;
 			tgtdev->dev_spec.pcie_inf.reset_to =
-			    pcieinf->controller_reset_to;
+			    max_t(u8, pcieinf->controller_reset_to,
+			     MPI3MR_INTADMCMD_TIMEOUT);
 			tgtdev->dev_spec.pcie_inf.abort_to =
-			    pcieinf->nv_me_abort_to;
+			    max_t(u8, pcieinf->nvme_abort_to,
+			    MPI3MR_INTADMCMD_TIMEOUT);
 		}
 		if (tgtdev->dev_spec.pcie_inf.mdts > (1024 * 1024))
 			tgtdev->dev_spec.pcie_inf.mdts = (1024 * 1024);
-		if ((dev_info & MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK) !=
-		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_NVME_DEVICE)
+		if (((dev_info & MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK) !=
+		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_NVME_DEVICE) &&
+		    ((dev_info & MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK) !=
+		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SCSI_DEVICE))
 			tgtdev->is_hidden = 1;
 		if (!mrioc->shost)
 			break;
@@ -1099,6 +1264,8 @@
 	mpi3mr_sastopochg_evt_debug(mrioc, event_data);
 
 	for (i = 0; i < event_data->num_entries; i++) {
+		if (fwevt->discard)
+			return;
 		handle = le16_to_cpu(event_data->phy_entry[i].attached_dev_handle);
 		if (!handle)
 			continue;
@@ -1230,6 +1397,8 @@
 	mpi3mr_pcietopochg_evt_debug(mrioc, event_data);
 
 	for (i = 0; i < event_data->num_entries; i++) {
+		if (fwevt->discard)
+			return;
 		handle =
 		    le16_to_cpu(event_data->port_entry[i].attached_dev_handle);
 		if (!handle)
@@ -1256,6 +1425,23 @@
 }
 
 /**
+ * mpi3mr_logdata_evt_bh -  Log data event bottomhalf
+ * @mrioc: Adapter instance reference
+ * @fwevt: Firmware event reference
+ *
+ * Extracts the event data and calls application interfacing
+ * function to process the event further.
+ *
+ * Return: Nothing.
+ */
+static void mpi3mr_logdata_evt_bh(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_fwevt *fwevt)
+{
+	mpi3mr_app_save_logdata(mrioc, fwevt->event_data,
+	    fwevt->event_data_size);
+}
+
+/**
  * mpi3mr_fwevt_bh - Firmware event bottomhalf handler
  * @mrioc: Adapter instance reference
  * @fwevt: Firmware event reference
@@ -1268,8 +1454,8 @@
 static void mpi3mr_fwevt_bh(struct mpi3mr_ioc *mrioc,
 	struct mpi3mr_fwevt *fwevt)
 {
-	mrioc->current_event = fwevt;
 	mpi3mr_fwevt_del_from_list(mrioc, fwevt);
+	mrioc->current_event = fwevt;
 
 	if (mrioc->stop_drv_processing)
 		goto out;
@@ -1307,13 +1493,18 @@
 		mpi3mr_pcietopochg_evt_bh(mrioc, fwevt);
 		break;
 	}
+	case MPI3_EVENT_LOG_DATA:
+	{
+		mpi3mr_logdata_evt_bh(mrioc, fwevt);
+		break;
+	}
 	default:
 		break;
 	}
 
 evt_ack:
 	if (fwevt->send_ack)
-		mpi3mr_send_event_ack(mrioc, fwevt->event_id,
+		mpi3mr_process_event_ack(mrioc, fwevt->event_id,
 		    fwevt->evt_ctx);
 out:
 	/* Put fwevt reference count to neutralize kref_init increment */
@@ -1377,24 +1568,33 @@
 }
 
 /**
- * mpi3mr_flush_delayed_rmhs_list - Flush pending commands
+ * mpi3mr_flush_delayed_cmd_lists - Flush pending commands
  * @mrioc: Adapter instance reference
  *
- * Flush pending commands in the delayed removal handshake list
- * due to a controller reset or driver removal as a cleanup.
+ * Flush pending commands in the delayed lists due to a
+ * controller reset or driver removal as a cleanup.
  *
  * Return: Nothing
  */
-void mpi3mr_flush_delayed_rmhs_list(struct mpi3mr_ioc *mrioc)
+void mpi3mr_flush_delayed_cmd_lists(struct mpi3mr_ioc *mrioc)
 {
 	struct delayed_dev_rmhs_node *_rmhs_node;
+	struct delayed_evt_ack_node *_evtack_node;
 
+	dprint_reset(mrioc, "flushing delayed dev_remove_hs commands\n");
 	while (!list_empty(&mrioc->delayed_rmhs_list)) {
 		_rmhs_node = list_entry(mrioc->delayed_rmhs_list.next,
 		    struct delayed_dev_rmhs_node, list);
 		list_del(&_rmhs_node->list);
 		kfree(_rmhs_node);
 	}
+	dprint_reset(mrioc, "flushing delayed event ack commands\n");
+	while (!list_empty(&mrioc->delayed_evtack_cmds_list)) {
+		_evtack_node = list_entry(mrioc->delayed_evtack_cmds_list.next,
+		    struct delayed_evt_ack_node, list);
+		list_del(&_evtack_node->list);
+		kfree(_evtack_node);
+	}
 }
 
 /**
@@ -1414,6 +1614,9 @@
 	u16 cmd_idx = drv_cmd->host_tag - MPI3MR_HOSTTAG_DEVRMCMD_MIN;
 	struct delayed_dev_rmhs_node *delayed_dev_rmhs = NULL;
 
+	if (drv_cmd->state & MPI3MR_CMD_RESET)
+		goto clear_drv_cmd;
+
 	ioc_info(mrioc,
 	    "%s :dev_rmhs_iouctrl_complete:handle(0x%04x), ioc_status(0x%04x), loginfo(0x%08x)\n",
 	    __func__, drv_cmd->dev_handle, drv_cmd->ioc_status,
@@ -1454,6 +1657,8 @@
 		kfree(delayed_dev_rmhs);
 		return;
 	}
+
+clear_drv_cmd:
 	drv_cmd->state = MPI3MR_CMD_NOTUSED;
 	drv_cmd->callback = NULL;
 	drv_cmd->retry_count = 0;
@@ -1480,6 +1685,9 @@
 	struct mpi3_scsi_task_mgmt_reply *tm_reply = NULL;
 	int retval;
 
+	if (drv_cmd->state & MPI3MR_CMD_RESET)
+		goto clear_drv_cmd;
+
 	if (drv_cmd->state & MPI3MR_CMD_REPLY_VALID)
 		tm_reply = (struct mpi3_scsi_task_mgmt_reply *)drv_cmd->reply;
 
@@ -1508,11 +1716,11 @@
 	if (retval) {
 		pr_err(IOCNAME "Issue DevRmHsTMIOUCTL: Admin post failed\n",
 		    mrioc->name);
-		goto out_failed;
+		goto clear_drv_cmd;
 	}
 
 	return;
-out_failed:
+clear_drv_cmd:
 	drv_cmd->state = MPI3MR_CMD_NOTUSED;
 	drv_cmd->callback = NULL;
 	drv_cmd->dev_handle = MPI3MR_INVALID_DEV_HANDLE;
@@ -1611,6 +1819,145 @@
 }
 
 /**
+ * mpi3mr_complete_evt_ack - event ack request completion
+ * @mrioc: Adapter instance reference
+ * @drv_cmd: Internal command tracker
+ *
+ * This is the completion handler for non blocking event
+ * acknowledgment sent to the firmware and this will issue any
+ * pending event acknowledgment request.
+ *
+ * Return: Nothing
+ */
+static void mpi3mr_complete_evt_ack(struct mpi3mr_ioc *mrioc,
+	struct mpi3mr_drv_cmd *drv_cmd)
+{
+	u16 cmd_idx = drv_cmd->host_tag - MPI3MR_HOSTTAG_EVTACKCMD_MIN;
+	struct delayed_evt_ack_node *delayed_evtack = NULL;
+
+	if (drv_cmd->state & MPI3MR_CMD_RESET)
+		goto clear_drv_cmd;
+
+	if (drv_cmd->ioc_status != MPI3_IOCSTATUS_SUCCESS) {
+		dprint_event_th(mrioc,
+		    "immediate event ack failed with ioc_status(0x%04x) log_info(0x%08x)\n",
+		    (drv_cmd->ioc_status & MPI3_IOCSTATUS_STATUS_MASK),
+		    drv_cmd->ioc_loginfo);
+	}
+
+	if (!list_empty(&mrioc->delayed_evtack_cmds_list)) {
+		delayed_evtack =
+			list_entry(mrioc->delayed_evtack_cmds_list.next,
+			    struct delayed_evt_ack_node, list);
+		mpi3mr_send_event_ack(mrioc, delayed_evtack->event, drv_cmd,
+		    delayed_evtack->event_ctx);
+		list_del(&delayed_evtack->list);
+		kfree(delayed_evtack);
+		return;
+	}
+clear_drv_cmd:
+	drv_cmd->state = MPI3MR_CMD_NOTUSED;
+	drv_cmd->callback = NULL;
+	clear_bit(cmd_idx, mrioc->evtack_cmds_bitmap);
+}
+
+/**
+ * mpi3mr_send_event_ack - Issue event acknwoledgment request
+ * @mrioc: Adapter instance reference
+ * @event: MPI3 event id
+ * @cmdparam: Internal command tracker
+ * @event_ctx: event context
+ *
+ * Issues event acknowledgment request to the firmware if there
+ * is a free command to send the event ack else it to a pend
+ * list so that it will be processed on a completion of a prior
+ * event acknowledgment .
+ *
+ * Return: Nothing
+ */
+static void mpi3mr_send_event_ack(struct mpi3mr_ioc *mrioc, u8 event,
+	struct mpi3mr_drv_cmd *cmdparam, u32 event_ctx)
+{
+	struct mpi3_event_ack_request evtack_req;
+	int retval = 0;
+	u8 retrycount = 5;
+	u16 cmd_idx = MPI3MR_NUM_EVTACKCMD;
+	struct mpi3mr_drv_cmd *drv_cmd = cmdparam;
+	struct delayed_evt_ack_node *delayed_evtack = NULL;
+
+	if (drv_cmd) {
+		dprint_event_th(mrioc,
+		    "sending delayed event ack in the top half for event(0x%02x), event_ctx(0x%08x)\n",
+		    event, event_ctx);
+		goto issue_cmd;
+	}
+	dprint_event_th(mrioc,
+	    "sending event ack in the top half for event(0x%02x), event_ctx(0x%08x)\n",
+	    event, event_ctx);
+	do {
+		cmd_idx = find_first_zero_bit(mrioc->evtack_cmds_bitmap,
+		    MPI3MR_NUM_EVTACKCMD);
+		if (cmd_idx < MPI3MR_NUM_EVTACKCMD) {
+			if (!test_and_set_bit(cmd_idx,
+			    mrioc->evtack_cmds_bitmap))
+				break;
+			cmd_idx = MPI3MR_NUM_EVTACKCMD;
+		}
+	} while (retrycount--);
+
+	if (cmd_idx >= MPI3MR_NUM_EVTACKCMD) {
+		delayed_evtack = kzalloc(sizeof(*delayed_evtack),
+		    GFP_ATOMIC);
+		if (!delayed_evtack)
+			return;
+		INIT_LIST_HEAD(&delayed_evtack->list);
+		delayed_evtack->event = event;
+		delayed_evtack->event_ctx = event_ctx;
+		list_add_tail(&delayed_evtack->list,
+		    &mrioc->delayed_evtack_cmds_list);
+		dprint_event_th(mrioc,
+		    "event ack in the top half for event(0x%02x), event_ctx(0x%08x) is postponed\n",
+		    event, event_ctx);
+		return;
+	}
+	drv_cmd = &mrioc->evtack_cmds[cmd_idx];
+
+issue_cmd:
+	cmd_idx = drv_cmd->host_tag - MPI3MR_HOSTTAG_EVTACKCMD_MIN;
+
+	memset(&evtack_req, 0, sizeof(evtack_req));
+	if (drv_cmd->state & MPI3MR_CMD_PENDING) {
+		dprint_event_th(mrioc,
+		    "sending event ack failed due to command in use\n");
+		goto out;
+	}
+	drv_cmd->state = MPI3MR_CMD_PENDING;
+	drv_cmd->is_waiting = 0;
+	drv_cmd->callback = mpi3mr_complete_evt_ack;
+	evtack_req.host_tag = cpu_to_le16(drv_cmd->host_tag);
+	evtack_req.function = MPI3_FUNCTION_EVENT_ACK;
+	evtack_req.event = event;
+	evtack_req.event_context = cpu_to_le32(event_ctx);
+	retval = mpi3mr_admin_request_post(mrioc, &evtack_req,
+	    sizeof(evtack_req), 1);
+	if (retval) {
+		dprint_event_th(mrioc,
+		    "posting event ack request is failed\n");
+		goto out_failed;
+	}
+
+	dprint_event_th(mrioc,
+	    "event ack in the top half for event(0x%02x), event_ctx(0x%08x) is posted\n",
+	    event, event_ctx);
+out:
+	return;
+out_failed:
+	drv_cmd->state = MPI3MR_CMD_NOTUSED;
+	drv_cmd->callback = NULL;
+	clear_bit(cmd_idx, mrioc->evtack_cmds_bitmap);
+}
+
+/**
  * mpi3mr_pcietopochg_evt_th - PCIETopologyChange evt tophalf
  * @mrioc: Adapter instance reference
  * @event_reply: event data
@@ -1819,6 +2166,40 @@
 }
 
 /**
+ * mpi3mr_preparereset_evt_th - Prepare for reset event tophalf
+ * @mrioc: Adapter instance reference
+ * @event_reply: event data
+ *
+ * Blocks and unblocks host level I/O based on the reason code
+ *
+ * Return: Nothing
+ */
+static void mpi3mr_preparereset_evt_th(struct mpi3mr_ioc *mrioc,
+	struct mpi3_event_notification_reply *event_reply)
+{
+	struct mpi3_event_data_prepare_for_reset *evtdata =
+	    (struct mpi3_event_data_prepare_for_reset *)event_reply->event_data;
+
+	if (evtdata->reason_code == MPI3_EVENT_PREPARE_RESET_RC_START) {
+		dprint_event_th(mrioc,
+		    "prepare for reset event top half with rc=start\n");
+		if (mrioc->prepare_for_reset)
+			return;
+		mrioc->prepare_for_reset = 1;
+		mrioc->prepare_for_reset_timeout_counter = 0;
+	} else if (evtdata->reason_code == MPI3_EVENT_PREPARE_RESET_RC_ABORT) {
+		dprint_event_th(mrioc,
+		    "prepare for reset top half with rc=abort\n");
+		mrioc->prepare_for_reset = 0;
+		mrioc->prepare_for_reset_timeout_counter = 0;
+	}
+	if ((event_reply->msg_flags & MPI3_EVENT_NOTIFY_MSGFLAGS_ACK_MASK)
+	    == MPI3_EVENT_NOTIFY_MSGFLAGS_ACK_REQUIRED)
+		mpi3mr_send_event_ack(mrioc, event_reply->event, NULL,
+		    le32_to_cpu(event_reply->event_context));
+}
+
+/**
  * mpi3mr_energypackchg_evt_th - Energy pack change evt tophalf
  * @mrioc: Adapter instance reference
  * @event_reply: event data
@@ -1848,6 +2229,42 @@
 }
 
 /**
+ * mpi3mr_cablemgmt_evt_th - Cable management event tophalf
+ * @mrioc: Adapter instance reference
+ * @event_reply: event data
+ *
+ * Displays Cable manegemt event details.
+ *
+ * Return: Nothing
+ */
+static void mpi3mr_cablemgmt_evt_th(struct mpi3mr_ioc *mrioc,
+	struct mpi3_event_notification_reply *event_reply)
+{
+	struct mpi3_event_data_cable_management *evtdata =
+	    (struct mpi3_event_data_cable_management *)event_reply->event_data;
+
+	switch (evtdata->status) {
+	case MPI3_EVENT_CABLE_MGMT_STATUS_INSUFFICIENT_POWER:
+	{
+		ioc_info(mrioc, "An active cable with receptacle_id %d cannot be powered.\n"
+		    "Devices connected to this cable are not detected.\n"
+		    "This cable requires %d mW of power.\n",
+		    evtdata->receptacle_id,
+		    le32_to_cpu(evtdata->active_cable_power_requirement));
+		break;
+	}
+	case MPI3_EVENT_CABLE_MGMT_STATUS_DEGRADED:
+	{
+		ioc_info(mrioc, "A cable with receptacle_id %d is not running at optimal speed\n",
+		    evtdata->receptacle_id);
+		break;
+	}
+	default:
+		break;
+	}
+}
+
+/**
  * mpi3mr_os_handle_events - Firmware event handler
  * @mrioc: Adapter instance reference
  * @event_reply: event data
@@ -1905,7 +2322,14 @@
 		mpi3mr_pcietopochg_evt_th(mrioc, event_reply);
 		break;
 	}
+	case MPI3_EVENT_PREPARE_FOR_RESET:
+	{
+		mpi3mr_preparereset_evt_th(mrioc, event_reply);
+		ack_req = 0;
+		break;
+	}
 	case MPI3_EVENT_DEVICE_INFO_CHANGED:
+	case MPI3_EVENT_LOG_DATA:
 	{
 		process_evt_bh = 1;
 		break;
@@ -1915,9 +2339,13 @@
 		mpi3mr_energypackchg_evt_th(mrioc, event_reply);
 		break;
 	}
+	case MPI3_EVENT_CABLE_MGMT:
+	{
+		mpi3mr_cablemgmt_evt_th(mrioc, event_reply);
+		break;
+	}
 	case MPI3_EVENT_ENCL_DEVICE_STATUS_CHANGE:
 	case MPI3_EVENT_SAS_DISCOVERY:
-	case MPI3_EVENT_CABLE_MGMT:
 	case MPI3_EVENT_SAS_DEVICE_DISCOVERY_ERROR:
 	case MPI3_EVENT_SAS_BROADCAST_PRIMITIVE:
 	case MPI3_EVENT_PCIE_ENUMERATION:
@@ -2204,6 +2632,8 @@
 		scmd->result = DID_OK << 16;
 		goto out_success;
 	}
+
+	scsi_set_resid(scmd, scsi_bufflen(scmd) - xfer_count);
 	if (ioc_status == MPI3_IOCSTATUS_SCSI_DATA_UNDERRUN &&
 	    xfer_count == 0 && (scsi_status == MPI3_SCSI_STATUS_BUSY ||
 	    scsi_status == MPI3_SCSI_STATUS_RESERVATION_CONFLICT ||
@@ -2403,6 +2833,17 @@
 		    scmd->sc_data_direction);
 		priv->meta_sg_valid = 1; /* To unmap meta sg DMA */
 	} else {
+		/*
+		 * Some firmware versions byte-swap the REPORT ZONES command
+		 * reply from ATA-ZAC devices by directly accessing in the host
+		 * buffer. This does not respect the default command DMA
+		 * direction and causes IOMMU page faults on some architectures
+		 * with an IOMMU enforcing write mappings (e.g. AMD hosts).
+		 * Avoid such issue by making the REPORT ZONES buffer mapping
+		 * bi-directional.
+		 */
+		if (scmd->cmnd[0] == ZBC_IN && scmd->cmnd[1] == ZI_REPORT_ZONES)
+			scmd->sc_data_direction = DMA_BIDIRECTIONAL;
 		sg_scmd = scsi_sglist(scmd);
 		sges_left = scsi_dma_map(scmd);
 	}
@@ -2520,49 +2961,63 @@
 }
 
 /**
- * mpi3mr_print_response_code - print TM response as a string
- * @mrioc: Adapter instance reference
+ * mpi3mr_tm_response_name -  get TM response as a string
  * @resp_code: TM response code
  *
- * Print TM response code as a readable string.
+ * Convert known task management response code as a readable
+ * string.
  *
- * Return: Nothing.
+ * Return: response code string.
  */
-static void mpi3mr_print_response_code(struct mpi3mr_ioc *mrioc, u8 resp_code)
+static const char *mpi3mr_tm_response_name(u8 resp_code)
 {
 	char *desc;
 
 	switch (resp_code) {
-	case MPI3MR_RSP_TM_COMPLETE:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_COMPLETE:
 		desc = "task management request completed";
 		break;
-	case MPI3MR_RSP_INVALID_FRAME:
+	case MPI3_SCSITASKMGMT_RSPCODE_INVALID_FRAME:
 		desc = "invalid frame";
 		break;
-	case MPI3MR_RSP_TM_NOT_SUPPORTED:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_FUNCTION_NOT_SUPPORTED:
 		desc = "task management request not supported";
 		break;
-	case MPI3MR_RSP_TM_FAILED:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_FAILED:
 		desc = "task management request failed";
 		break;
-	case MPI3MR_RSP_TM_SUCCEEDED:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_SUCCEEDED:
 		desc = "task management request succeeded";
 		break;
-	case MPI3MR_RSP_TM_INVALID_LUN:
-		desc = "invalid lun";
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_INVALID_LUN:
+		desc = "invalid LUN";
 		break;
-	case MPI3MR_RSP_TM_OVERLAPPED_TAG:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_OVERLAPPED_TAG:
 		desc = "overlapped tag attempted";
 		break;
-	case MPI3MR_RSP_IO_QUEUED_ON_IOC:
+	case MPI3_SCSITASKMGMT_RSPCODE_IO_QUEUED_ON_IOC:
 		desc = "task queued, however not sent to target";
 		break;
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_NVME_DENIED:
+		desc = "task management request denied by NVMe device";
+		break;
 	default:
 		desc = "unknown";
 		break;
 	}
-	ioc_info(mrioc, "%s :response_code(0x%01x): %s\n", __func__,
-	    resp_code, desc);
+
+	return desc;
+}
+
+inline void mpi3mr_poll_pend_io_completions(struct mpi3mr_ioc *mrioc)
+{
+	int i;
+	int num_of_reply_queues =
+	    mrioc->num_op_reply_q + mrioc->op_reply_q_offset;
+
+	for (i = mrioc->op_reply_q_offset; i < num_of_reply_queues; i++)
+		mpi3mr_process_op_reply_q(mrioc,
+		    mrioc->intr_info[i].op_reply_q);
 }
 
 /**
@@ -2572,9 +3027,10 @@
  * @handle: Device handle
  * @lun: lun ID
  * @htag: Host tag of the TM request
+ * @timeout: TM timeout value
  * @drv_cmd: Internal command tracker
  * @resp_code: Response code place holder
- * @cmd_priv: SCSI command private data
+ * @scmd: SCSI command
  *
  * Issues a Task Management Request to the controller for a
  * specified target, lun and command and wait for its completion
@@ -2583,17 +3039,19 @@
  *
  * Return: 0 on success, non-zero on errors
  */
-static int mpi3mr_issue_tm(struct mpi3mr_ioc *mrioc, u8 tm_type,
+int mpi3mr_issue_tm(struct mpi3mr_ioc *mrioc, u8 tm_type,
 	u16 handle, uint lun, u16 htag, ulong timeout,
 	struct mpi3mr_drv_cmd *drv_cmd,
-	u8 *resp_code, struct scmd_priv *cmd_priv)
+	u8 *resp_code, struct scsi_cmnd *scmd)
 {
 	struct mpi3_scsi_task_mgmt_request tm_req;
 	struct mpi3_scsi_task_mgmt_reply *tm_reply = NULL;
 	int retval = 0;
 	struct mpi3mr_tgt_dev *tgtdev = NULL;
 	struct mpi3mr_stgt_priv_data *scsi_tgt_priv_data = NULL;
-	struct op_req_qinfo *op_req_q = NULL;
+	struct scmd_priv *cmd_priv = NULL;
+	struct scsi_device *sdev = NULL;
+	struct mpi3mr_sdev_priv_data *sdev_priv_data = NULL;
 
 	ioc_info(mrioc, "%s :Issue TM: TM type (0x%x) for devhandle 0x%04x\n",
 	     __func__, tm_type, handle);
@@ -2630,16 +3088,21 @@
 	tm_req.function = MPI3_FUNCTION_SCSI_TASK_MGMT;
 
 	tgtdev = mpi3mr_get_tgtdev_by_handle(mrioc, handle);
-	if (tgtdev && tgtdev->starget && tgtdev->starget->hostdata) {
-		scsi_tgt_priv_data = (struct mpi3mr_stgt_priv_data *)
-		    tgtdev->starget->hostdata;
-		atomic_inc(&scsi_tgt_priv_data->block_io);
-	}
-	if (cmd_priv) {
-		op_req_q = &mrioc->req_qinfo[cmd_priv->req_q_idx];
-		tm_req.task_host_tag = cpu_to_le16(cmd_priv->host_tag);
-		tm_req.task_request_queue_id = cpu_to_le16(op_req_q->qid);
+
+	if (scmd) {
+		sdev = scmd->device;
+		sdev_priv_data = sdev->hostdata;
+		scsi_tgt_priv_data = ((sdev_priv_data) ?
+		    sdev_priv_data->tgt_priv_data : NULL);
+	} else {
+		if (tgtdev && tgtdev->starget && tgtdev->starget->hostdata)
+			scsi_tgt_priv_data = (struct mpi3mr_stgt_priv_data *)
+			    tgtdev->starget->hostdata;
 	}
+
+	if (scsi_tgt_priv_data)
+		atomic_inc(&scsi_tgt_priv_data->block_io);
+
 	if (tgtdev && (tgtdev->dev_type == MPI3_DEVICE_DEVFORM_PCIE)) {
 		if (cmd_priv && tgtdev->dev_spec.pcie_inf.abort_to)
 			timeout = tgtdev->dev_spec.pcie_inf.abort_to;
@@ -2656,39 +3119,49 @@
 	wait_for_completion_timeout(&drv_cmd->done, (timeout * HZ));
 
 	if (!(drv_cmd->state & MPI3MR_CMD_COMPLETE)) {
-		ioc_err(mrioc, "%s :Issue TM: command timed out\n", __func__);
 		drv_cmd->is_waiting = 0;
 		retval = -1;
-		mpi3mr_soft_reset_handler(mrioc,
-		    MPI3MR_RESET_FROM_TM_TIMEOUT, 1);
+		if (!(drv_cmd->state & MPI3MR_CMD_RESET)) {
+			dprint_tm(mrioc,
+			    "task management request timed out after %ld seconds\n",
+			    timeout);
+			if (mrioc->logging_level & MPI3_DEBUG_TM)
+				dprint_dump_req(&tm_req, sizeof(tm_req)/4);
+			mpi3mr_soft_reset_handler(mrioc,
+			    MPI3MR_RESET_FROM_TM_TIMEOUT, 1);
+		}
 		goto out_unlock;
 	}
 
-	if (drv_cmd->state & MPI3MR_CMD_REPLY_VALID)
-		tm_reply = (struct mpi3_scsi_task_mgmt_reply *)drv_cmd->reply;
-
-	if (drv_cmd->ioc_status != MPI3_IOCSTATUS_SUCCESS) {
-		ioc_err(mrioc,
-		    "%s :Issue TM: handle(0x%04x) Failed ioc_status(0x%04x) Loginfo(0x%08x)\n",
-		    __func__, handle, drv_cmd->ioc_status,
-		    drv_cmd->ioc_loginfo);
+	if (!(drv_cmd->state & MPI3MR_CMD_REPLY_VALID)) {
+		dprint_tm(mrioc, "invalid task management reply message\n");
 		retval = -1;
 		goto out_unlock;
 	}
 
-	if (!tm_reply) {
-		ioc_err(mrioc, "%s :Issue TM: No TM Reply message\n", __func__);
+	tm_reply = (struct mpi3_scsi_task_mgmt_reply *)drv_cmd->reply;
+
+	switch (drv_cmd->ioc_status) {
+	case MPI3_IOCSTATUS_SUCCESS:
+		*resp_code = le32_to_cpu(tm_reply->response_data) &
+			MPI3MR_RI_MASK_RESPCODE;
+		break;
+	case MPI3_IOCSTATUS_SCSI_IOC_TERMINATED:
+		*resp_code = MPI3_SCSITASKMGMT_RSPCODE_TM_COMPLETE;
+		break;
+	default:
+		dprint_tm(mrioc,
+		    "task management request to handle(0x%04x) is failed with ioc_status(0x%04x) log_info(0x%08x)\n",
+		    handle, drv_cmd->ioc_status, drv_cmd->ioc_loginfo);
 		retval = -1;
 		goto out_unlock;
 	}
 
-	*resp_code = le32_to_cpu(tm_reply->response_data) &
-	    MPI3MR_RI_MASK_RESPCODE;
 	switch (*resp_code) {
-	case MPI3MR_RSP_TM_SUCCEEDED:
-	case MPI3MR_RSP_TM_COMPLETE:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_SUCCEEDED:
+	case MPI3_SCSITASKMGMT_RSPCODE_TM_COMPLETE:
 		break;
-	case MPI3MR_RSP_IO_QUEUED_ON_IOC:
+	case MPI3_SCSITASKMGMT_RSPCODE_IO_QUEUED_ON_IOC:
 		if (tm_type != MPI3_SCSITASKMGMT_TASKTYPE_QUERY_TASK)
 			retval = -1;
 		break;
@@ -2697,14 +3170,37 @@
 		break;
 	}
 
-	ioc_info(mrioc,
-	    "%s :Issue TM: Completed TM type (0x%x) handle(0x%04x) ",
-	    __func__, tm_type, handle);
-	ioc_info(mrioc,
-	    "with ioc_status(0x%04x), loginfo(0x%08x), term_count(0x%08x)\n",
-	    drv_cmd->ioc_status, drv_cmd->ioc_loginfo,
-	    le32_to_cpu(tm_reply->termination_count));
-	mpi3mr_print_response_code(mrioc, *resp_code);
+	dprint_tm(mrioc,
+	    "task management request type(%d) completed for handle(0x%04x) with ioc_status(0x%04x), log_info(0x%08x), termination_count(%d), response:%s(0x%x)\n",
+	    tm_type, handle, drv_cmd->ioc_status, drv_cmd->ioc_loginfo,
+	    le32_to_cpu(tm_reply->termination_count),
+	    mpi3mr_tm_response_name(*resp_code), *resp_code);
+
+	if (!retval) {
+		mpi3mr_ioc_disable_intr(mrioc);
+		mpi3mr_poll_pend_io_completions(mrioc);
+		mpi3mr_ioc_enable_intr(mrioc);
+		mpi3mr_poll_pend_io_completions(mrioc);
+	}
+	switch (tm_type) {
+	case MPI3_SCSITASKMGMT_TASKTYPE_TARGET_RESET:
+		if (!scsi_tgt_priv_data)
+			break;
+		scsi_tgt_priv_data->pend_count = 0;
+		blk_mq_tagset_busy_iter(&mrioc->shost->tag_set,
+		    mpi3mr_count_tgt_pending,
+		    (void *)scsi_tgt_priv_data->starget);
+		break;
+	case MPI3_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET:
+		if (!sdev_priv_data)
+			break;
+		sdev_priv_data->pend_count = 0;
+		blk_mq_tagset_busy_iter(&mrioc->shost->tag_set,
+		    mpi3mr_count_dev_pending, (void *)sdev);
+		break;
+	default:
+		break;
+	}
 
 out_unlock:
 	drv_cmd->state = MPI3MR_CMD_NOTUSED;
@@ -2713,14 +3209,6 @@
 		atomic_dec_if_positive(&scsi_tgt_priv_data->block_io);
 	if (tgtdev)
 		mpi3mr_tgtdev_put(tgtdev);
-	if (!retval) {
-		/*
-		 * Flush all IRQ handlers by calling synchronize_irq().
-		 * mpi3mr_ioc_disable_intr() takes care of it.
-		 */
-		mpi3mr_ioc_disable_intr(mrioc);
-		mpi3mr_ioc_enable_intr(mrioc);
-	}
 out:
 	return retval;
 }
@@ -2769,17 +3257,49 @@
  * mpi3mr_map_queues - Map queues callback handler
  * @shost: SCSI host reference
  *
- * Call the blk_mq_pci_map_queues with from which operational
- * queue the mapping has to be done
+ * Maps default and poll queues.
  *
- * Return: return of blk_mq_pci_map_queues
+ * Return: return zero.
  */
 static int mpi3mr_map_queues(struct Scsi_Host *shost)
 {
 	struct mpi3mr_ioc *mrioc = shost_priv(shost);
+	int i, qoff, offset;
+	struct blk_mq_queue_map *map = NULL;
+
+	offset = mrioc->op_reply_q_offset;
+
+	for (i = 0, qoff = 0; i < HCTX_MAX_TYPES; i++) {
+		map = &shost->tag_set.map[i];
+
+		map->nr_queues  = 0;
+
+		if (i == HCTX_TYPE_DEFAULT)
+			map->nr_queues = mrioc->default_qcount;
+		else if (i == HCTX_TYPE_POLL)
+			map->nr_queues = mrioc->active_poll_qcount;
+
+		if (!map->nr_queues) {
+			BUG_ON(i == HCTX_TYPE_DEFAULT);
+			continue;
+		}
+
+		/*
+		 * The poll queue(s) doesn't have an IRQ (and hence IRQ
+		 * affinity), so use the regular blk-mq cpu mapping
+		 */
+		map->queue_offset = qoff;
+		if (i != HCTX_TYPE_POLL)
+			blk_mq_pci_map_queues(map, mrioc->pdev, offset);
+		else
+			blk_mq_map_queues(map);
+
+		qoff += map->nr_queues;
+		offset += map->nr_queues;
+	}
+
+	return 0;
 
-	return blk_mq_pci_map_queues(&shost->tag_set.map[HCTX_TYPE_DEFAULT],
-	    mrioc->pdev, mrioc->op_reply_q_offset);
 }
 
 /**
@@ -2938,6 +3458,13 @@
 
 	stgt_priv_data = sdev_priv_data->tgt_priv_data;
 	dev_handle = stgt_priv_data->dev_handle;
+	if (stgt_priv_data->dev_removed) {
+		sdev_printk(KERN_INFO, scmd->device,
+		    "%s:target(handle = 0x%04x) is removed, target reset is not issued\n",
+		    mrioc->name, dev_handle);
+		retval = FAILED;
+		goto out;
+	}
 	sdev_printk(KERN_INFO, scmd->device,
 	    "Target Reset is issued to handle(0x%04x)\n",
 	    dev_handle);
@@ -2945,15 +3472,22 @@
 	ret = mpi3mr_issue_tm(mrioc,
 	    MPI3_SCSITASKMGMT_TASKTYPE_TARGET_RESET, dev_handle,
 	    sdev_priv_data->lun_id, MPI3MR_HOSTTAG_BLK_TMS,
-	    MPI3MR_RESETTM_TIMEOUT, &mrioc->host_tm_cmds, &resp_code, NULL);
+	    MPI3MR_RESETTM_TIMEOUT, &mrioc->host_tm_cmds, &resp_code, scmd);
 
 	if (ret)
 		goto out;
 
+	if (stgt_priv_data->pend_count) {
+		sdev_printk(KERN_INFO, scmd->device,
+		    "%s: target has %d pending commands, target reset is failed\n",
+		    mrioc->name, stgt_priv_data->pend_count);
+		goto out;
+	}
+
 	retval = SUCCESS;
 out:
 	sdev_printk(KERN_INFO, scmd->device,
-	    "Target reset is %s for scmd(%p)\n",
+	    "%s: target reset is %s for scmd(%p)\n", mrioc->name,
 	    ((retval == SUCCESS) ? "SUCCESS" : "FAILED"), scmd);
 
 	return retval;
@@ -2992,21 +3526,34 @@
 
 	stgt_priv_data = sdev_priv_data->tgt_priv_data;
 	dev_handle = stgt_priv_data->dev_handle;
+	if (stgt_priv_data->dev_removed) {
+		sdev_printk(KERN_INFO, scmd->device,
+		    "%s: device(handle = 0x%04x) is removed, device(LUN) reset is not issued\n",
+		    mrioc->name, dev_handle);
+		retval = FAILED;
+		goto out;
+	}
 	sdev_printk(KERN_INFO, scmd->device,
 	    "Device(lun) Reset is issued to handle(0x%04x)\n", dev_handle);
 
 	ret = mpi3mr_issue_tm(mrioc,
 	    MPI3_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET, dev_handle,
 	    sdev_priv_data->lun_id, MPI3MR_HOSTTAG_BLK_TMS,
-	    MPI3MR_RESETTM_TIMEOUT, &mrioc->host_tm_cmds, &resp_code, NULL);
+	    MPI3MR_RESETTM_TIMEOUT, &mrioc->host_tm_cmds, &resp_code, scmd);
 
 	if (ret)
 		goto out;
 
+	if (sdev_priv_data->pend_count) {
+		sdev_printk(KERN_INFO, scmd->device,
+		    "%s: device has %d pending commands, device(LUN) reset is failed\n",
+		    mrioc->name, sdev_priv_data->pend_count);
+		goto out;
+	}
 	retval = SUCCESS;
 out:
 	sdev_printk(KERN_INFO, scmd->device,
-	    "Device(lun) reset is %s for scmd(%p)\n",
+	    "%s: device(LUN) reset is %s for scmd(%p)\n", mrioc->name,
 	    ((retval == SUCCESS) ? "SUCCESS" : "FAILED"), scmd);
 
 	return retval;
@@ -3049,32 +3596,43 @@
 {
 	struct mpi3mr_ioc *mrioc = shost_priv(shost);
 	u32 pe_timeout = MPI3MR_PORTENABLE_TIMEOUT;
+	u32 ioc_status = readl(&mrioc->sysif_regs->ioc_status);
 
-	if (time >= (pe_timeout * HZ)) {
+	if ((ioc_status & MPI3_SYSIF_IOC_STATUS_RESET_HISTORY) ||
+	    (ioc_status & MPI3_SYSIF_IOC_STATUS_FAULT)) {
+		ioc_err(mrioc, "port enable failed due to fault or reset\n");
+		mpi3mr_print_fault_info(mrioc);
+		mrioc->scan_failed = MPI3_IOCSTATUS_INTERNAL_ERROR;
+		mrioc->scan_started = 0;
 		mrioc->init_cmds.is_waiting = 0;
 		mrioc->init_cmds.callback = NULL;
 		mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
-		ioc_err(mrioc, "%s :port enable request timed out\n", __func__);
-		mrioc->is_driver_loading = 0;
-		mpi3mr_soft_reset_handler(mrioc,
-		    MPI3MR_RESET_FROM_PE_TIMEOUT, 1);
 	}
 
-	if (mrioc->scan_failed) {
-		ioc_err(mrioc,
-		    "%s :port enable failed with (ioc_status=0x%08x)\n",
-		    __func__, mrioc->scan_failed);
-		mrioc->is_driver_loading = 0;
-		mrioc->stop_drv_processing = 1;
-		return 1;
+	if (time >= (pe_timeout * HZ)) {
+		ioc_err(mrioc, "port enable failed due to time out\n");
+		mpi3mr_check_rh_fault_ioc(mrioc,
+		    MPI3MR_RESET_FROM_PE_TIMEOUT);
+		mrioc->scan_failed = MPI3_IOCSTATUS_INTERNAL_ERROR;
+		mrioc->scan_started = 0;
+		mrioc->init_cmds.is_waiting = 0;
+		mrioc->init_cmds.callback = NULL;
+		mrioc->init_cmds.state = MPI3MR_CMD_NOTUSED;
 	}
 
 	if (mrioc->scan_started)
 		return 0;
-	ioc_info(mrioc, "%s :port enable: SUCCESS\n", __func__);
+
+	if (mrioc->scan_failed) {
+		ioc_err(mrioc,
+		    "port enable failed with status=0x%04x\n",
+		    mrioc->scan_failed);
+	} else
+		ioc_info(mrioc, "port enable is successfully completed\n");
+
 	mpi3mr_start_watchdog(mrioc);
 	mrioc->is_driver_loading = 0;
-
+	mrioc->stop_bsgs = 0;
 	return 1;
 }
 
@@ -3186,13 +3744,25 @@
 		return -ENXIO;
 
 	mpi3mr_change_queue_depth(sdev, tgt_dev->q_depth);
+
+	sdev->eh_timeout = MPI3MR_EH_SCMD_TIMEOUT;
+	blk_queue_rq_timeout(sdev->request_queue, MPI3MR_SCMD_TIMEOUT);
+
 	switch (tgt_dev->dev_type) {
 	case MPI3_DEVICE_DEVFORM_PCIE:
 		/*The block layer hw sector size = 512*/
-		blk_queue_max_hw_sectors(sdev->request_queue,
-		    tgt_dev->dev_spec.pcie_inf.mdts / 512);
-		blk_queue_virt_boundary(sdev->request_queue,
-		    ((1 << tgt_dev->dev_spec.pcie_inf.pgsz) - 1));
+		if ((tgt_dev->dev_spec.pcie_inf.dev_info &
+		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_MASK) ==
+		    MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_NVME_DEVICE) {
+			blk_queue_max_hw_sectors(sdev->request_queue,
+			    tgt_dev->dev_spec.pcie_inf.mdts / 512);
+			if (tgt_dev->dev_spec.pcie_inf.pgsz == 0)
+				blk_queue_virt_boundary(sdev->request_queue,
+				    ((1 << MPI3MR_DEFAULT_PGSZEXP) - 1));
+			else
+				blk_queue_virt_boundary(sdev->request_queue,
+				    ((1 << tgt_dev->dev_spec.pcie_inf.pgsz) - 1));
+		}
 		break;
 	default:
 		break;
@@ -3312,9 +3882,22 @@
 	struct scsi_cmnd *scmd)
 {
 	unsigned char *buf;
-	u16 param_len, desc_len;
+	u16 param_len, desc_len, trunc_param_len;
+
+	trunc_param_len = param_len = get_unaligned_be16(scmd->cmnd + 7);
 
-	param_len = get_unaligned_be16(scmd->cmnd + 7);
+	if (mrioc->pdev->revision) {
+		if ((param_len > 24) && ((param_len - 8) & 0xF)) {
+			trunc_param_len -= (param_len - 8) & 0xF;
+			dprint_scsi_command(mrioc, scmd, MPI3_DEBUG_SCSI_ERROR);
+			dprint_scsi_err(mrioc,
+			    "truncating param_len from (%d) to (%d)\n",
+			    param_len, trunc_param_len);
+			put_unaligned_be16(trunc_param_len, scmd->cmnd + 7);
+			dprint_scsi_command(mrioc, scmd, MPI3_DEBUG_SCSI_ERROR);
+		}
+		return false;
+	}
 
 	if (!param_len) {
 		ioc_warn(mrioc,
@@ -3374,12 +3957,12 @@
 	}
 
 	if (param_len > (desc_len + 8)) {
+		trunc_param_len = desc_len + 8;
 		scsi_print_command(scmd);
-		ioc_warn(mrioc,
-		    "%s: Truncating param_len(%d) to desc_len+8(%d)\n",
-		    __func__, param_len, (desc_len + 8));
-		param_len = desc_len + 8;
-		put_unaligned_be16(param_len, scmd->cmnd + 7);
+		dprint_scsi_err(mrioc,
+		    "truncating param_len(%d) to desc_len+8(%d)\n",
+		    param_len, trunc_param_len);
+		put_unaligned_be16(trunc_param_len, scmd->cmnd + 7);
 		scsi_print_command(scmd);
 	}
 
@@ -3434,6 +4017,13 @@
 	u32 scsiio_flags = 0;
 	struct request *rq = scsi_cmd_to_rq(scmd);
 	int iprio_class;
+	u8 is_pcie_dev = 0;
+
+	if (mrioc->unrecoverable) {
+		scmd->result = DID_ERROR << 16;
+		scmd->scsi_done(scmd);
+		goto out;
+	}
 
 	sdev_priv_data = scmd->device->hostdata;
 	if (!sdev_priv_data || !sdev_priv_data->tgt_priv_data) {
@@ -3478,8 +4068,10 @@
 		goto out;
 	}
 
-	if ((scmd->cmnd[0] == UNMAP) &&
-	    (stgt_priv_data->dev_type == MPI3_DEVICE_DEVFORM_PCIE) &&
+	if (stgt_priv_data->dev_type == MPI3_DEVICE_DEVFORM_PCIE)
+		is_pcie_dev = 1;
+	if ((scmd->cmnd[0] == UNMAP) && is_pcie_dev &&
+	    (mrioc->pdev->device == MPI3_MFGPAGE_DEVID_SAS4116) &&
 	    mpi3mr_check_return_unmap(mrioc, scmd))
 		goto out;
 
@@ -3541,6 +4133,72 @@
 	return retval;
 }
 
+/**
+ * sas_ncq_prio_supported_show - Indicate if device supports NCQ priority
+ * @dev: pointer to embedded device
+ * @attr: sas_ncq_prio_supported attribute descriptor
+ * @buf: the buffer returned
+ *
+ * A sysfs 'read-only' sdev attribute, only works with SATA devices
+ */
+static ssize_t
+sas_ncq_prio_supported_show(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+
+	return sysfs_emit(buf, "%d\n", sas_ata_ncq_prio_supported(sdev));
+}
+static DEVICE_ATTR_RO(sas_ncq_prio_supported);
+
+/**
+ * sas_ncq_prio_enable_show - send prioritized io commands to device
+ * @dev: pointer to embedded device
+ * @attr: sas_ncq_prio_enable attribute descriptor
+ * @buf: the buffer returned
+ *
+ * A sysfs 'read/write' sdev attribute, only works with SATA devices
+ */
+static ssize_t
+sas_ncq_prio_enable_show(struct device *dev,
+			 struct device_attribute *attr, char *buf)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	struct mpi3mr_sdev_priv_data *sdev_priv_data =  sdev->hostdata;
+
+	if (!sdev_priv_data)
+		return 0;
+
+	return sysfs_emit(buf, "%d\n", sdev_priv_data->ncq_prio_enable);
+}
+
+static ssize_t
+sas_ncq_prio_enable_store(struct device *dev,
+			  struct device_attribute *attr,
+			  const char *buf, size_t count)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	struct mpi3mr_sdev_priv_data *sdev_priv_data =  sdev->hostdata;
+	bool ncq_prio_enable = 0;
+
+	if (kstrtobool(buf, &ncq_prio_enable))
+		return -EINVAL;
+
+	if (!sas_ata_ncq_prio_supported(sdev))
+		return -EINVAL;
+
+	sdev_priv_data->ncq_prio_enable = ncq_prio_enable;
+
+	return strlen(buf);
+}
+static DEVICE_ATTR_RW(sas_ncq_prio_enable);
+
+static struct device_attribute *mpi3mr_dev_attrs[] = {
+	&dev_attr_sas_ncq_prio_supported,
+	&dev_attr_sas_ncq_prio_enable,
+	NULL,
+};
+
 static struct scsi_host_template mpi3mr_driver_template = {
 	.module				= THIS_MODULE,
 	.name				= "MPI3 Storage Controller",
@@ -3559,6 +4217,7 @@
 	.eh_host_reset_handler		= mpi3mr_eh_host_reset,
 	.bios_param			= mpi3mr_bios_param,
 	.map_queues			= mpi3mr_map_queues,
+	.mq_poll                        = mpi3mr_blk_mq_poll,
 	.no_write_same			= 1,
 	.can_queue			= 1,
 	.this_id			= -1,
@@ -3567,8 +4226,11 @@
 	 */
 	.max_sectors			= 2048,
 	.cmd_per_lun			= MPI3MR_MAX_CMDS_LUN,
+	.max_segment_size		= 0xffffffff,
 	.track_queue_depth		= 1,
 	.cmd_size			= sizeof(struct scmd_priv),
+	.sdev_groups			= mpi3mr_dev_groups,
+	.sdev_attrs			= mpi3mr_dev_attrs,
 };
 
 /**
@@ -3714,10 +4376,12 @@
 	INIT_LIST_HEAD(&mrioc->fwevt_list);
 	INIT_LIST_HEAD(&mrioc->tgtdev_list);
 	INIT_LIST_HEAD(&mrioc->delayed_rmhs_list);
+	INIT_LIST_HEAD(&mrioc->delayed_evtack_cmds_list);
 
 	mutex_init(&mrioc->reset_mutex);
 	mpi3mr_init_drv_cmd(&mrioc->init_cmds, MPI3MR_HOSTTAG_INITCMDS);
 	mpi3mr_init_drv_cmd(&mrioc->host_tm_cmds, MPI3MR_HOSTTAG_BLK_TMS);
+	mpi3mr_init_drv_cmd(&mrioc->bsg_cmds, MPI3MR_HOSTTAG_BSG_CMDS);
 
 	for (i = 0; i < MPI3MR_NUM_DEVRMCMD; i++)
 		mpi3mr_init_drv_cmd(&mrioc->dev_rmhs_cmds[i],
@@ -3730,6 +4394,7 @@
 	mrioc->logging_level = logging_level;
 	mrioc->shost = shost;
 	mrioc->pdev = pdev;
+	mrioc->stop_bsgs = 1;
 
 	/* init shost parameters */
 	shost->max_cmd_len = MPI3MR_MAX_CDB_LENGTH;
@@ -3767,26 +4432,34 @@
 	snprintf(mrioc->fwevt_worker_name, sizeof(mrioc->fwevt_worker_name),
 	    "%s%d_fwevt_wrkr", mrioc->driver_name, mrioc->id);
 	mrioc->fwevt_worker_thread = alloc_ordered_workqueue(
-	    mrioc->fwevt_worker_name, WQ_MEM_RECLAIM);
+	    mrioc->fwevt_worker_name, 0);
 	if (!mrioc->fwevt_worker_thread) {
 		ioc_err(mrioc, "failure at %s:%d/%s()!\n",
 		    __FILE__, __LINE__, __func__);
 		retval = -ENODEV;
-		goto out_fwevtthread_failed;
+		goto fwevtthread_failed;
 	}
 
 	mrioc->is_driver_loading = 1;
-	if (mpi3mr_init_ioc(mrioc, MPI3MR_IT_INIT)) {
-		ioc_err(mrioc, "failure at %s:%d/%s()!\n",
-		    __FILE__, __LINE__, __func__);
+	mrioc->cpu_count = num_online_cpus();
+	if (mpi3mr_setup_resources(mrioc)) {
+		ioc_err(mrioc, "setup resources failed\n");
+		retval = -ENODEV;
+		goto resource_alloc_failed;
+	}
+	if (mpi3mr_init_ioc(mrioc)) {
+		ioc_err(mrioc, "initializing IOC failed\n");
 		retval = -ENODEV;
-		goto out_iocinit_failed;
+		goto init_ioc_failed;
 	}
 
 	shost->nr_hw_queues = mrioc->num_op_reply_q;
+	if (mrioc->active_poll_qcount)
+		shost->nr_maps = 3;
+
 	shost->can_queue = mrioc->max_host_ios;
 	shost->sg_tablesize = MPI3MR_SG_DEPTH;
-	shost->max_id = mrioc->facts.max_perids;
+	shost->max_id = mrioc->facts.max_perids + 1;
 
 	retval = scsi_add_host(shost, &pdev->dev);
 	if (retval) {
@@ -3796,13 +4469,18 @@
 	}
 
 	scsi_scan_host(shost);
+	mpi3mr_bsg_init(mrioc);
 	return retval;
 
 addhost_failed:
-	mpi3mr_cleanup_ioc(mrioc, MPI3MR_COMPLETE_CLEANUP);
-out_iocinit_failed:
+	mpi3mr_stop_watchdog(mrioc);
+	mpi3mr_cleanup_ioc(mrioc);
+init_ioc_failed:
+	mpi3mr_free_mem(mrioc);
+	mpi3mr_cleanup_resources(mrioc);
+resource_alloc_failed:
 	destroy_workqueue(mrioc->fwevt_worker_thread);
-out_fwevtthread_failed:
+fwevtthread_failed:
 	spin_lock(&mrioc_list_lock);
 	list_del(&mrioc->list);
 	spin_unlock(&mrioc_list_lock);
@@ -3815,6 +4493,7 @@
  * mpi3mr_remove - PCI remove callback
  * @pdev: PCI device instance
  *
+ * Cleanup the IOC by issuing MUR and shutdown notification.
  * Free up all memory and resources associated with the
  * controllerand target devices, unregister the shost.
  *
@@ -3835,6 +4514,7 @@
 	while (mrioc->reset_in_progress || mrioc->is_driver_loading)
 		ssleep(1);
 
+	mpi3mr_bsg_exit(mrioc);
 	mrioc->stop_drv_processing = 1;
 	mpi3mr_cleanup_fwevt_list(mrioc);
 	spin_lock_irqsave(&mrioc->fwevt_lock, flags);
@@ -3851,7 +4531,10 @@
 		mpi3mr_tgtdev_del_from_list(mrioc, tgtdev);
 		mpi3mr_tgtdev_put(tgtdev);
 	}
-	mpi3mr_cleanup_ioc(mrioc, MPI3MR_COMPLETE_CLEANUP);
+	mpi3mr_stop_watchdog(mrioc);
+	mpi3mr_cleanup_ioc(mrioc);
+	mpi3mr_free_mem(mrioc);
+	mpi3mr_cleanup_resources(mrioc);
 
 	spin_lock(&mrioc_list_lock);
 	list_del(&mrioc->list);
@@ -3891,7 +4574,10 @@
 	spin_unlock_irqrestore(&mrioc->fwevt_lock, flags);
 	if (wq)
 		destroy_workqueue(wq);
-	mpi3mr_cleanup_ioc(mrioc, MPI3MR_COMPLETE_CLEANUP);
+
+	mpi3mr_stop_watchdog(mrioc);
+	mpi3mr_cleanup_ioc(mrioc);
+	mpi3mr_cleanup_resources(mrioc);
 }
 
 #ifdef CONFIG_PM
@@ -3921,14 +4607,14 @@
 	mpi3mr_cleanup_fwevt_list(mrioc);
 	scsi_block_requests(shost);
 	mpi3mr_stop_watchdog(mrioc);
-	mpi3mr_cleanup_ioc(mrioc, MPI3MR_SUSPEND);
+	mpi3mr_cleanup_ioc(mrioc);
 
 	device_state = pci_choose_state(pdev, state);
 	ioc_info(mrioc, "pdev=0x%p, slot=%s, entering operating state [D%d]\n",
 	    pdev, pci_name(pdev), device_state);
 	pci_save_state(pdev);
-	pci_set_power_state(pdev, device_state);
 	mpi3mr_cleanup_resources(mrioc);
+	pci_set_power_state(pdev, device_state);
 
 	return 0;
 }
@@ -3970,7 +4656,11 @@
 
 	mrioc->stop_drv_processing = 0;
 	mpi3mr_memset_buffers(mrioc);
-	mpi3mr_init_ioc(mrioc, MPI3MR_IT_RESUME);
+	r = mpi3mr_reinit_ioc(mrioc, 1);
+	if (r) {
+		ioc_err(mrioc, "resuming controller failed[%d]\n", r);
+		return r;
+	}
 	scsi_unblock_requests(shost);
 	mpi3mr_start_watchdog(mrioc);
 
@@ -3980,8 +4670,8 @@
 
 static const struct pci_device_id mpi3mr_pci_id_table[] = {
 	{
-		PCI_DEVICE_SUB(PCI_VENDOR_ID_LSI_LOGIC, 0x00A5,
-		    PCI_ANY_ID, PCI_ANY_ID)
+		PCI_DEVICE_SUB(MPI3_MFGPAGE_VENDORID_BROADCOM,
+		    MPI3_MFGPAGE_DEVID_SAS4116, PCI_ANY_ID, PCI_ANY_ID)
 	},
 	{ 0 }
 };
@@ -3999,6 +4689,12 @@
 #endif
 };
 
+static ssize_t event_counter_show(struct device_driver *dd, char *buf)
+{
+	return sprintf(buf, "%llu\n", atomic64_read(&event_counter));
+}
+static DRIVER_ATTR_RO(event_counter);
+
 static int __init mpi3mr_init(void)
 {
 	int ret_val;
@@ -4007,6 +4703,16 @@
 	    MPI3MR_DRIVER_VERSION);
 
 	ret_val = pci_register_driver(&mpi3mr_pci_driver);
+	if (ret_val) {
+		pr_err("%s failed to load due to pci register driver failure\n",
+		    MPI3MR_DRIVER_NAME);
+		return ret_val;
+	}
+
+	ret_val = driver_create_file(&mpi3mr_pci_driver.driver,
+				     &driver_attr_event_counter);
+	if (ret_val)
+		pci_unregister_driver(&mpi3mr_pci_driver);
 
 	return ret_val;
 }
@@ -4021,6 +4727,8 @@
 		pr_info("Unloading %s version %s\n", MPI3MR_DRIVER_NAME,
 		    MPI3MR_DRIVER_VERSION);
 
+	driver_remove_file(&mpi3mr_pci_driver.driver,
+			   &driver_attr_event_counter);
 	pci_unregister_driver(&mpi3mr_pci_driver);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -139,6 +139,9 @@
 static void
 _base_clear_outstanding_commands(struct MPT3SAS_ADAPTER *ioc);
 
+static u32
+_base_readl_ext_retry(const volatile void __iomem *addr);
+
 /**
  * mpt3sas_base_check_cmd_timeout - Function
  *		to check timeout and command termination due
@@ -214,6 +217,20 @@
 	return ret_val;
 }
 
+static u32
+_base_readl_ext_retry(const volatile void __iomem *addr)
+{
+	u32 i, ret_val;
+
+	for (i = 0 ; i < 30 ; i++) {
+		ret_val = readl(addr);
+		if (ret_val != 0)
+			break;
+	}
+
+	return ret_val;
+}
+
 static inline u32
 _base_readl(const volatile void __iomem *addr)
 {
@@ -639,8 +656,8 @@
 	mpi_request->IOCParameter = MPI26_SET_IOC_PARAMETER_SYNC_TIMESTAMP;
 	current_time = ktime_get_real();
 	TimeStamp = ktime_to_ms(current_time);
-	mpi_request->Reserved7 = cpu_to_le32(TimeStamp & 0xFFFFFFFF);
-	mpi_request->IOCParameterValue = cpu_to_le32(TimeStamp >> 32);
+	mpi_request->Reserved7 = cpu_to_le32(TimeStamp >> 32);
+	mpi_request->IOCParameterValue = cpu_to_le32(TimeStamp & 0xFFFFFFFF);
 	init_completion(&ioc->scsih_cmds.done);
 	ioc->put_smid_default(ioc, smid);
 	dinitprintk(ioc, ioc_info(ioc,
@@ -941,7 +958,7 @@
 
 	dump_stack();
 
-	doorbell = ioc->base_readl(&ioc->chip->Doorbell);
+	doorbell = ioc->base_readl_ext_retry(&ioc->chip->Doorbell);
 	if ((doorbell & MPI2_IOC_STATE_MASK) == MPI2_IOC_STATE_FAULT) {
 		mpt3sas_print_fault_code(ioc, doorbell &
 		    MPI2_DOORBELL_DATA_MASK);
@@ -2011,9 +2028,10 @@
 				enable_irq(reply_q->os_irq);
 			}
 		}
+
+		if (poll)
+			_base_process_reply_queue(reply_q);
 	}
-	if (poll)
-		_base_process_reply_queue(reply_q);
 }
 
 /**
@@ -2593,12 +2611,8 @@
 
 	/* Get the SG list pointer and info. */
 	sges_left = scsi_dma_map(scmd);
-	if (sges_left < 0) {
-		sdev_printk(KERN_ERR, scmd->device,
-			"scsi_dma_map failed: request for %d bytes!\n",
-			scsi_bufflen(scmd));
+	if (sges_left < 0)
 		return 1;
-	}
 
 	/* Check if we need to build a native SG list. */
 	if (!base_is_prp_possible(ioc, pcie_device,
@@ -2658,6 +2672,22 @@
 	_base_add_sg_single_ieee(paddr, sgl_flags, 0, 0, -1);
 }
 
+static inline int _base_scsi_dma_map(struct scsi_cmnd *cmd)
+{
+	/*
+	 * Some firmware versions byte-swap the REPORT ZONES command reply from
+	 * ATA-ZAC devices by directly accessing in the host buffer. This does
+	 * not respect the default command DMA direction and causes IOMMU page
+	 * faults on some architectures with an IOMMU enforcing write mappings
+	 * (e.g. AMD hosts). Avoid such issue by making the report zones buffer
+	 * mapping bi-directional.
+	 */
+	if (cmd->cmnd[0] == ZBC_IN && cmd->cmnd[1] == ZI_REPORT_ZONES)
+		cmd->sc_data_direction = DMA_BIDIRECTIONAL;
+
+	return scsi_dma_map(cmd);
+}
+
 /**
  * _base_build_sg_scmd - main sg creation routine
  *		pcie_device is unused here!
@@ -2704,13 +2734,9 @@
 	sgl_flags = sgl_flags << MPI2_SGE_FLAGS_SHIFT;
 
 	sg_scmd = scsi_sglist(scmd);
-	sges_left = scsi_dma_map(scmd);
-	if (sges_left < 0) {
-		sdev_printk(KERN_ERR, scmd->device,
-		 "scsi_dma_map failed: request for %d bytes!\n",
-		 scsi_bufflen(scmd));
+	sges_left = _base_scsi_dma_map(scmd);
+	if (sges_left < 0)
 		return -ENOMEM;
-	}
 
 	sg_local = &mpi_request->SGL;
 	sges_in_segment = ioc->max_sges_in_main_message;
@@ -2852,13 +2878,9 @@
 	}
 
 	sg_scmd = scsi_sglist(scmd);
-	sges_left = scsi_dma_map(scmd);
-	if (sges_left < 0) {
-		sdev_printk(KERN_ERR, scmd->device,
-			"scsi_dma_map failed: request for %d bytes!\n",
-			scsi_bufflen(scmd));
+	sges_left = _base_scsi_dma_map(scmd);
+	if (sges_left < 0)
 		return -ENOMEM;
-	}
 
 	sg_local = &mpi_request->SGL;
 	sges_in_segment = (ioc->request_sz -
@@ -3001,19 +3023,25 @@
 _base_config_dma_addressing(struct MPT3SAS_ADAPTER *ioc, struct pci_dev *pdev)
 {
 	struct sysinfo s;
+	u64 coherent_dma_mask, dma_mask;
 
-	if (ioc->is_mcpu_endpoint ||
-	    sizeof(dma_addr_t) == 4 || ioc->use_32bit_dma ||
-	    dma_get_required_mask(&pdev->dev) <= 32)
+	if (ioc->is_mcpu_endpoint || sizeof(dma_addr_t) == 4) {
 		ioc->dma_mask = 32;
+		coherent_dma_mask = dma_mask = DMA_BIT_MASK(32);
 	/* Set 63 bit DMA mask for all SAS3 and SAS35 controllers */
-	else if (ioc->hba_mpi_version_belonged > MPI2_VERSION)
+	} else if (ioc->hba_mpi_version_belonged > MPI2_VERSION) {
 		ioc->dma_mask = 63;
-	else
+		coherent_dma_mask = dma_mask = DMA_BIT_MASK(63);
+	} else {
 		ioc->dma_mask = 64;
+		coherent_dma_mask = dma_mask = DMA_BIT_MASK(64);
+	}
+
+	if (ioc->use_32bit_dma)
+		coherent_dma_mask = DMA_BIT_MASK(32);
 
-	if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(ioc->dma_mask)) ||
-	    dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(ioc->dma_mask)))
+	if (dma_set_mask(&pdev->dev, dma_mask) ||
+	    dma_set_coherent_mask(&pdev->dev, coherent_dma_mask))
 		return -ENODEV;
 
 	if (ioc->dma_mask > 32) {
@@ -5380,6 +5408,7 @@
 	Mpi2ConfigReply_t mpi_reply;
 	Mpi2SasIOUnitPage1_t *sas_iounit_pg1 = NULL;
 	Mpi26PCIeIOUnitPage1_t pcie_iounit_pg1;
+	u16 depth;
 	int sz;
 	int rc = 0;
 
@@ -5391,7 +5420,7 @@
 		goto out;
 	/* sas iounit page 1 */
 	sz = offsetof(Mpi2SasIOUnitPage1_t, PhyData);
-	sas_iounit_pg1 = kzalloc(sz, GFP_KERNEL);
+	sas_iounit_pg1 = kzalloc(sizeof(Mpi2SasIOUnitPage1_t), GFP_KERNEL);
 	if (!sas_iounit_pg1) {
 		pr_err("%s: failure at %s:%d/%s()!\n",
 		    ioc->name, __FILE__, __LINE__, __func__);
@@ -5404,16 +5433,16 @@
 		    ioc->name, __FILE__, __LINE__, __func__);
 		goto out;
 	}
-	ioc->max_wideport_qd =
-	    (le16_to_cpu(sas_iounit_pg1->SASWideMaxQueueDepth)) ?
-	    le16_to_cpu(sas_iounit_pg1->SASWideMaxQueueDepth) :
-	    MPT3SAS_SAS_QUEUE_DEPTH;
-	ioc->max_narrowport_qd =
-	    (le16_to_cpu(sas_iounit_pg1->SASNarrowMaxQueueDepth)) ?
-	    le16_to_cpu(sas_iounit_pg1->SASNarrowMaxQueueDepth) :
-	    MPT3SAS_SAS_QUEUE_DEPTH;
-	ioc->max_sata_qd = (sas_iounit_pg1->SATAMaxQDepth) ?
-	    sas_iounit_pg1->SATAMaxQDepth : MPT3SAS_SATA_QUEUE_DEPTH;
+
+	depth = le16_to_cpu(sas_iounit_pg1->SASWideMaxQueueDepth);
+	ioc->max_wideport_qd = (depth ? depth : MPT3SAS_SAS_QUEUE_DEPTH);
+
+	depth = le16_to_cpu(sas_iounit_pg1->SASNarrowMaxQueueDepth);
+	ioc->max_narrowport_qd = (depth ? depth : MPT3SAS_SAS_QUEUE_DEPTH);
+
+	depth = sas_iounit_pg1->SATAMaxQDepth;
+	ioc->max_sata_qd = (depth ? depth : MPT3SAS_SATA_QUEUE_DEPTH);
+
 	/* pcie iounit page 1 */
 	rc = mpt3sas_config_get_pcie_iounit_pg1(ioc, &mpi_reply,
 	    &pcie_iounit_pg1, sizeof(Mpi26PCIeIOUnitPage1_t));
@@ -5468,8 +5497,7 @@
 	if (!ioc->is_gen35_ioc && ioc->manu_pg11.EEDPTagMode == 0) {
 		pr_err("%s: overriding NVDATA EEDPTagMode setting\n",
 		    ioc->name);
-		ioc->manu_pg11.EEDPTagMode &= ~0x3;
-		ioc->manu_pg11.EEDPTagMode |= 0x1;
+		ioc->manu_pg11.EEDPTagMode = 0x1;
 		mpt3sas_config_set_manufacturing_pg11(ioc, &mpi_reply,
 		    &ioc->manu_pg11);
 	}
@@ -5692,6 +5720,9 @@
 		}
 		dma_pool_destroy(ioc->pcie_sgl_dma_pool);
 	}
+	kfree(ioc->pcie_sg_lookup);
+	ioc->pcie_sg_lookup = NULL;
+
 	if (ioc->config_page) {
 		dexitprintk(ioc,
 			    ioc_info(ioc, "config_page(0x%p): free\n",
@@ -5736,14 +5767,13 @@
  */
 
 static int
-mpt3sas_check_same_4gb_region(long reply_pool_start_address, u32 pool_sz)
+mpt3sas_check_same_4gb_region(dma_addr_t start_address, u32 pool_sz)
 {
-	long reply_pool_end_address;
+	dma_addr_t end_address;
 
-	reply_pool_end_address = reply_pool_start_address + pool_sz;
+	end_address = start_address + pool_sz - 1;
 
-	if (upper_32_bits(reply_pool_start_address) ==
-		upper_32_bits(reply_pool_end_address))
+	if (upper_32_bits(start_address) == upper_32_bits(end_address))
 		return 1;
 	else
 		return 0;
@@ -5804,7 +5834,7 @@
 		}
 
 		if (!mpt3sas_check_same_4gb_region(
-		    (long)ioc->pcie_sg_lookup[i].pcie_sgl, sz)) {
+		    ioc->pcie_sg_lookup[i].pcie_sgl_dma, sz)) {
 			ioc_err(ioc, "PCIE SGLs are not in same 4G !! pcie sgl (0x%p) dma = (0x%llx)\n",
 			    ioc->pcie_sg_lookup[i].pcie_sgl,
 			    (unsigned long long)
@@ -5859,8 +5889,8 @@
 			    GFP_KERNEL, &ctr->chain_buffer_dma);
 			if (!ctr->chain_buffer)
 				return -EAGAIN;
-			if (!mpt3sas_check_same_4gb_region((long)
-			    ctr->chain_buffer, ioc->chain_segment_sz)) {
+			if (!mpt3sas_check_same_4gb_region(
+			    ctr->chain_buffer_dma, ioc->chain_segment_sz)) {
 				ioc_err(ioc,
 				    "Chain buffers are not in same 4G !!! Chain buff (0x%p) dma = (0x%llx)\n",
 				    ctr->chain_buffer,
@@ -5896,7 +5926,7 @@
 	    GFP_KERNEL, &ioc->sense_dma);
 	if (!ioc->sense)
 		return -EAGAIN;
-	if (!mpt3sas_check_same_4gb_region((long)ioc->sense, sz)) {
+	if (!mpt3sas_check_same_4gb_region(ioc->sense_dma, sz)) {
 		dinitprintk(ioc, pr_err(
 		    "Bad Sense Pool! sense (0x%p) sense_dma = (0x%llx)\n",
 		    ioc->sense, (unsigned long long) ioc->sense_dma));
@@ -5929,7 +5959,7 @@
 	    &ioc->reply_dma);
 	if (!ioc->reply)
 		return -EAGAIN;
-	if (!mpt3sas_check_same_4gb_region((long)ioc->reply_free, sz)) {
+	if (!mpt3sas_check_same_4gb_region(ioc->reply_dma, sz)) {
 		dinitprintk(ioc, pr_err(
 		    "Bad Reply Pool! Reply (0x%p) Reply dma = (0x%llx)\n",
 		    ioc->reply, (unsigned long long) ioc->reply_dma));
@@ -5964,7 +5994,7 @@
 	    GFP_KERNEL, &ioc->reply_free_dma);
 	if (!ioc->reply_free)
 		return -EAGAIN;
-	if (!mpt3sas_check_same_4gb_region((long)ioc->reply_free, sz)) {
+	if (!mpt3sas_check_same_4gb_region(ioc->reply_free_dma, sz)) {
 		dinitprintk(ioc,
 		    pr_err("Bad Reply Free Pool! Reply Free (0x%p) Reply Free dma = (0x%llx)\n",
 		    ioc->reply_free, (unsigned long long) ioc->reply_free_dma));
@@ -6003,7 +6033,7 @@
 	    GFP_KERNEL, &ioc->reply_post_free_array_dma);
 	if (!ioc->reply_post_free_array)
 		return -EAGAIN;
-	if (!mpt3sas_check_same_4gb_region((long)ioc->reply_post_free_array,
+	if (!mpt3sas_check_same_4gb_region(ioc->reply_post_free_array_dma,
 	    reply_post_free_array_sz)) {
 		dinitprintk(ioc, pr_err(
 		    "Bad Reply Free Pool! Reply Free (0x%p) Reply Free dma = (0x%llx)\n",
@@ -6068,7 +6098,7 @@
 			 * resources and set DMA mask to 32 and allocate.
 			 */
 			if (!mpt3sas_check_same_4gb_region(
-				(long)ioc->reply_post[i].reply_post_free, sz)) {
+				ioc->reply_post[i].reply_post_free_dma, sz)) {
 				dinitprintk(ioc,
 				    ioc_err(ioc, "bad Replypost free pool(0x%p)"
 				    "reply_post_free_dma = (0x%llx)\n",
@@ -6458,11 +6488,6 @@
 	else if (rc == -EAGAIN)
 		goto try_32bit_dma;
 	total_sz += sense_sz;
-	ioc_info(ioc,
-	    "sense pool(0x%p)- dma(0x%llx): depth(%d),"
-	    "element_size(%d), pool_size(%d kB)\n",
-	    ioc->sense, (unsigned long long)ioc->sense_dma, ioc->scsiio_depth,
-	    SCSI_SENSE_BUFFERSIZE, sz / 1024);
 	/* reply pool, 4 byte align */
 	sz = ioc->reply_free_queue_depth * ioc->reply_sz;
 	rc = _base_allocate_reply_pool(ioc, sz);
@@ -6544,7 +6569,7 @@
 {
 	u32 s, sc;
 
-	s = ioc->base_readl(&ioc->chip->Doorbell);
+	s = ioc->base_readl_ext_retry(&ioc->chip->Doorbell);
 	sc = s & MPI2_IOC_STATE_MASK;
 	return cooked ? sc : s;
 }
@@ -6689,7 +6714,7 @@
 					   __func__, count, timeout));
 			return 0;
 		} else if (int_status & MPI2_HIS_IOC2SYS_DB_STATUS) {
-			doorbell = ioc->base_readl(&ioc->chip->Doorbell);
+			doorbell = ioc->base_readl_ext_retry(&ioc->chip->Doorbell);
 			if ((doorbell & MPI2_IOC_STATE_MASK) ==
 			    MPI2_IOC_STATE_FAULT) {
 				mpt3sas_print_fault_code(ioc, doorbell);
@@ -6729,7 +6754,7 @@
 	count = 0;
 	cntdn = 1000 * timeout;
 	do {
-		doorbell_reg = ioc->base_readl(&ioc->chip->Doorbell);
+		doorbell_reg = ioc->base_readl_ext_retry(&ioc->chip->Doorbell);
 		if (!(doorbell_reg & MPI2_DOORBELL_USED)) {
 			dhsprintk(ioc,
 				  ioc_info(ioc, "%s: successful count(%d), timeout(%d)\n",
@@ -6875,11 +6900,12 @@
 	int i;
 	u8 failed;
 	__le32 *mfp;
+	int ret_val;
 
 	/* make sure doorbell is not in use */
-	if ((ioc->base_readl(&ioc->chip->Doorbell) & MPI2_DOORBELL_USED)) {
+	if ((ioc->base_readl_ext_retry(&ioc->chip->Doorbell) & MPI2_DOORBELL_USED)) {
 		ioc_err(ioc, "doorbell is in use (line=%d)\n", __LINE__);
-		return -EFAULT;
+		goto doorbell_diag_reset;
 	}
 
 	/* clear pending doorbell interrupts from previous state changes */
@@ -6926,7 +6952,7 @@
 	}
 
 	/* read the first two 16-bits, it gives the total length of the reply */
-	reply[0] = le16_to_cpu(ioc->base_readl(&ioc->chip->Doorbell)
+	reply[0] = le16_to_cpu(ioc->base_readl_ext_retry(&ioc->chip->Doorbell)
 	    & MPI2_DOORBELL_DATA_MASK);
 	writel(0, &ioc->chip->HostInterruptStatus);
 	if ((_base_wait_for_doorbell_int(ioc, 5))) {
@@ -6934,7 +6960,7 @@
 			__LINE__);
 		return -EFAULT;
 	}
-	reply[1] = le16_to_cpu(ioc->base_readl(&ioc->chip->Doorbell)
+	reply[1] = le16_to_cpu(ioc->base_readl_ext_retry(&ioc->chip->Doorbell)
 	    & MPI2_DOORBELL_DATA_MASK);
 	writel(0, &ioc->chip->HostInterruptStatus);
 
@@ -6945,10 +6971,10 @@
 			return -EFAULT;
 		}
 		if (i >=  reply_bytes/2) /* overflow case */
-			ioc->base_readl(&ioc->chip->Doorbell);
+			ioc->base_readl_ext_retry(&ioc->chip->Doorbell);
 		else
 			reply[i] = le16_to_cpu(
-			    ioc->base_readl(&ioc->chip->Doorbell)
+			    ioc->base_readl_ext_retry(&ioc->chip->Doorbell)
 			    & MPI2_DOORBELL_DATA_MASK);
 		writel(0, &ioc->chip->HostInterruptStatus);
 	}
@@ -6969,6 +6995,10 @@
 			    le32_to_cpu(mfp[i]));
 	}
 	return 0;
+
+doorbell_diag_reset:
+	ret_val = _base_diag_reset(ioc);
+	return ret_val;
 }
 
 /**
@@ -7228,7 +7258,9 @@
 		return -EFAULT;
 	}
 
- issue_diag_reset:
+	return 0;
+
+issue_diag_reset:
 	rc = _base_diag_reset(ioc);
 	return rc;
 }
@@ -7807,7 +7839,7 @@
 			goto out;
 		}
 
-		host_diagnostic = ioc->base_readl(&ioc->chip->HostDiagnostic);
+		host_diagnostic = ioc->base_readl_ext_retry(&ioc->chip->HostDiagnostic);
 		drsprintk(ioc,
 			  ioc_info(ioc, "wrote magic sequence: count(%d), host_diagnostic(0x%08x)\n",
 				   count, host_diagnostic));
@@ -7827,7 +7859,7 @@
 	for (count = 0; count < (300000000 /
 		MPI2_HARD_RESET_PCIE_SECOND_READ_DELAY_MICRO_SEC); count++) {
 
-		host_diagnostic = ioc->base_readl(&ioc->chip->HostDiagnostic);
+		host_diagnostic = ioc->base_readl_ext_retry(&ioc->chip->HostDiagnostic);
 
 		if (host_diagnostic == 0xFFFFFFFF) {
 			ioc_info(ioc,
@@ -8217,10 +8249,13 @@
 	ioc->rdpq_array_enable_assigned = 0;
 	ioc->use_32bit_dma = false;
 	ioc->dma_mask = 64;
-	if (ioc->is_aero_ioc)
+	if (ioc->is_aero_ioc) {
 		ioc->base_readl = &_base_readl_aero;
-	else
+		ioc->base_readl_ext_retry = &_base_readl_ext_retry;
+	} else {
 		ioc->base_readl = &_base_readl;
+		ioc->base_readl_ext_retry = &_base_readl;
+	}
 	r = mpt3sas_base_map_resources(ioc);
 	if (r)
 		goto out_free_resources;
@@ -8322,6 +8357,12 @@
 	ioc->pd_handles_sz = (ioc->facts.MaxDevHandle / 8);
 	if (ioc->facts.MaxDevHandle % 8)
 		ioc->pd_handles_sz++;
+	/*
+	 * pd_handles_sz should have, at least, the minimal room for
+	 * set_bit()/test_bit(), otherwise out-of-memory touch may occur.
+	 */
+	ioc->pd_handles_sz = ALIGN(ioc->pd_handles_sz, sizeof(unsigned long));
+
 	ioc->pd_handles = kzalloc(ioc->pd_handles_sz,
 	    GFP_KERNEL);
 	if (!ioc->pd_handles) {
@@ -8339,6 +8380,13 @@
 	ioc->pend_os_device_add_sz = (ioc->facts.MaxDevHandle / 8);
 	if (ioc->facts.MaxDevHandle % 8)
 		ioc->pend_os_device_add_sz++;
+
+	/*
+	 * pend_os_device_add_sz should have, at least, the minimal room for
+	 * set_bit()/test_bit(), otherwise out-of-memory may occur.
+	 */
+	ioc->pend_os_device_add_sz = ALIGN(ioc->pend_os_device_add_sz,
+					   sizeof(unsigned long));
 	ioc->pend_os_device_add = kzalloc(ioc->pend_os_device_add_sz,
 	    GFP_KERNEL);
 	if (!ioc->pend_os_device_add) {
@@ -8630,6 +8678,12 @@
 		if (ioc->facts.MaxDevHandle % 8)
 			pd_handles_sz++;
 
+		/*
+		 * pd_handles should have, at least, the minimal room for
+		 * set_bit()/test_bit(), otherwise out-of-memory touch may
+		 * occur.
+		 */
+		pd_handles_sz = ALIGN(pd_handles_sz, sizeof(unsigned long));
 		pd_handles = krealloc(ioc->pd_handles, pd_handles_sz,
 		    GFP_KERNEL);
 		if (!pd_handles) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -77,8 +77,8 @@
 #define MPT3SAS_DRIVER_NAME		"mpt3sas"
 #define MPT3SAS_AUTHOR "Avago Technologies <MPT-FusionLinux.pdl@avagotech.com>"
 #define MPT3SAS_DESCRIPTION	"LSI MPT Fusion SAS 3.0 Device Driver"
-#define MPT3SAS_DRIVER_VERSION		"39.100.00.00"
-#define MPT3SAS_MAJOR_VERSION		39
+#define MPT3SAS_DRIVER_VERSION		"40.100.00.00"
+#define MPT3SAS_MAJOR_VERSION		40
 #define MPT3SAS_MINOR_VERSION		100
 #define MPT3SAS_BUILD_VERSION		0
 #define MPT3SAS_RELEASE_VERSION	00
@@ -142,6 +142,8 @@
 
 #define MPT_MAX_CALLBACKS		32
 
+#define MPT_MAX_HBA_NUM_PHYS		32
+
 #define INTERNAL_CMDS_COUNT		10	/* reserved cmds */
 /* reserved for issuing internally framed scsi io cmds */
 #define INTERNAL_SCSIIO_CMDS_COUNT	3
@@ -798,6 +800,7 @@
  * @enclosure_handle: handle for this a member of an enclosure
  * @device_info: bitwise defining capabilities of this sas_host/expander
  * @responding: used in _scsih_expander_device_mark_responding
+ * @nr_phys_allocated: Allocated memory for this many count phys
  * @phy: a list of phys that make up this sas_host/expander
  * @sas_port_list: list of ports attached to this sas_host/expander
  * @port: hba port entry containing node's port number info
@@ -813,6 +816,7 @@
 	u16	enclosure_handle;
 	u64	enclosure_logical_id;
 	u8	responding;
+	u8	nr_phys_allocated;
 	struct hba_port *port;
 	struct	_sas_phy *phy;
 	struct list_head sas_port_list;
@@ -1614,6 +1618,7 @@
 	u8		diag_trigger_active;
 	u8		atomic_desc_capable;
 	BASE_READ_REG	base_readl;
+	BASE_READ_REG	base_readl_ext_retry;
 	struct SL_WH_MASTER_TRIGGER_T diag_trigger_master;
 	struct SL_WH_EVENT_TRIGGERS_T diag_trigger_event;
 	struct SL_WH_SCSI_TRIGGERS_T diag_trigger_scsi;
@@ -2005,9 +2010,6 @@
 mpt3sas_setup_direct_io(struct MPT3SAS_ADAPTER *ioc, struct scsi_cmnd *scmd,
 	struct _raid_device *raid_device, Mpi25SCSIIORequest_t *mpi_request);
 
-/* NCQ Prio Handling Check */
-bool scsih_ncq_prio_supp(struct scsi_device *sdev);
-
 void mpt3sas_setup_debugfs(struct MPT3SAS_ADAPTER *ioc);
 void mpt3sas_destroy_debugfs(struct MPT3SAS_ADAPTER *ioc);
 void mpt3sas_init_debugfs(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpt3sas/mpt3sas_config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpt3sas/mpt3sas_config.c
@@ -394,10 +394,13 @@
 		retry_count++;
 		if (ioc->config_cmds.smid == smid)
 			mpt3sas_base_free_smid(ioc, smid);
-		if ((ioc->shost_recovery) || (ioc->config_cmds.status &
-		    MPT3_CMD_RESET) || ioc->pci_error_recovery)
+		if (ioc->config_cmds.status & MPT3_CMD_RESET)
 			goto retry_config;
-		issue_host_reset = 1;
+		if (ioc->shost_recovery || ioc->pci_error_recovery) {
+			issue_host_reset = 0;
+			r = -EFAULT;
+		} else
+			issue_host_reset = 1;
 		goto free_mem;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpt3sas/mpt3sas_ctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpt3sas/mpt3sas_ctl.c
@@ -3533,11 +3533,31 @@
 {
 	struct Scsi_Host *shost = class_to_shost(cdev);
 	struct MPT3SAS_ADAPTER *ioc = shost_priv(shost);
+	struct SL_WH_MASTER_TRIGGER_T *master_tg;
 	unsigned long flags;
 	ssize_t rc;
+	bool set = 1;
 
-	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
 	rc = min(sizeof(struct SL_WH_MASTER_TRIGGER_T), count);
+
+	if (ioc->supports_trigger_pages) {
+		master_tg = kzalloc(sizeof(struct SL_WH_MASTER_TRIGGER_T),
+		    GFP_KERNEL);
+		if (!master_tg)
+			return -ENOMEM;
+
+		memcpy(master_tg, buf, rc);
+		if (!master_tg->MasterData)
+			set = 0;
+		if (mpt3sas_config_update_driver_trigger_pg1(ioc, master_tg,
+		    set)) {
+			kfree(master_tg);
+			return -EFAULT;
+		}
+		kfree(master_tg);
+	}
+
+	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
 	memset(&ioc->diag_trigger_master, 0,
 	    sizeof(struct SL_WH_MASTER_TRIGGER_T));
 	memcpy(&ioc->diag_trigger_master, buf, rc);
@@ -3589,11 +3609,31 @@
 {
 	struct Scsi_Host *shost = class_to_shost(cdev);
 	struct MPT3SAS_ADAPTER *ioc = shost_priv(shost);
+	struct SL_WH_EVENT_TRIGGERS_T *event_tg;
 	unsigned long flags;
 	ssize_t sz;
+	bool set = 1;
 
-	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
 	sz = min(sizeof(struct SL_WH_EVENT_TRIGGERS_T), count);
+	if (ioc->supports_trigger_pages) {
+		event_tg = kzalloc(sizeof(struct SL_WH_EVENT_TRIGGERS_T),
+		    GFP_KERNEL);
+		if (!event_tg)
+			return -ENOMEM;
+
+		memcpy(event_tg, buf, sz);
+		if (!event_tg->ValidEntries)
+			set = 0;
+		if (mpt3sas_config_update_driver_trigger_pg2(ioc, event_tg,
+		    set)) {
+			kfree(event_tg);
+			return -EFAULT;
+		}
+		kfree(event_tg);
+	}
+
+	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
+
 	memset(&ioc->diag_trigger_event, 0,
 	    sizeof(struct SL_WH_EVENT_TRIGGERS_T));
 	memcpy(&ioc->diag_trigger_event, buf, sz);
@@ -3644,11 +3684,31 @@
 {
 	struct Scsi_Host *shost = class_to_shost(cdev);
 	struct MPT3SAS_ADAPTER *ioc = shost_priv(shost);
+	struct SL_WH_SCSI_TRIGGERS_T *scsi_tg;
 	unsigned long flags;
 	ssize_t sz;
+	bool set = 1;
+
+	sz = min(sizeof(struct SL_WH_SCSI_TRIGGERS_T), count);
+	if (ioc->supports_trigger_pages) {
+		scsi_tg = kzalloc(sizeof(struct SL_WH_SCSI_TRIGGERS_T),
+		    GFP_KERNEL);
+		if (!scsi_tg)
+			return -ENOMEM;
+
+		memcpy(scsi_tg, buf, sz);
+		if (!scsi_tg->ValidEntries)
+			set = 0;
+		if (mpt3sas_config_update_driver_trigger_pg3(ioc, scsi_tg,
+		    set)) {
+			kfree(scsi_tg);
+			return -EFAULT;
+		}
+		kfree(scsi_tg);
+	}
 
 	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
-	sz = min(sizeof(ioc->diag_trigger_scsi), count);
+
 	memset(&ioc->diag_trigger_scsi, 0, sizeof(ioc->diag_trigger_scsi));
 	memcpy(&ioc->diag_trigger_scsi, buf, sz);
 	if (ioc->diag_trigger_scsi.ValidEntries > NUM_VALID_ENTRIES)
@@ -3698,11 +3758,30 @@
 {
 	struct Scsi_Host *shost = class_to_shost(cdev);
 	struct MPT3SAS_ADAPTER *ioc = shost_priv(shost);
+	struct SL_WH_MPI_TRIGGERS_T *mpi_tg;
 	unsigned long flags;
 	ssize_t sz;
+	bool set = 1;
 
-	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
 	sz = min(sizeof(struct SL_WH_MPI_TRIGGERS_T), count);
+	if (ioc->supports_trigger_pages) {
+		mpi_tg = kzalloc(sizeof(struct SL_WH_MPI_TRIGGERS_T),
+		    GFP_KERNEL);
+		if (!mpi_tg)
+			return -ENOMEM;
+
+		memcpy(mpi_tg, buf, sz);
+		if (!mpi_tg->ValidEntries)
+			set = 0;
+		if (mpt3sas_config_update_driver_trigger_pg4(ioc, mpi_tg,
+		    set)) {
+			kfree(mpi_tg);
+			return -EFAULT;
+		}
+		kfree(mpi_tg);
+	}
+
+	spin_lock_irqsave(&ioc->diag_trigger_lock, flags);
 	memset(&ioc->diag_trigger_mpi, 0,
 	    sizeof(ioc->diag_trigger_mpi));
 	memcpy(&ioc->diag_trigger_mpi, buf, sz);
@@ -3933,7 +4012,7 @@
 {
 	struct scsi_device *sdev = to_scsi_device(dev);
 
-	return sysfs_emit(buf, "%d\n", scsih_ncq_prio_supp(sdev));
+	return sysfs_emit(buf, "%d\n", sas_ata_ncq_prio_supported(sdev));
 }
 static DEVICE_ATTR_RO(sas_ncq_prio_supported);
 
@@ -3968,7 +4047,7 @@
 	if (kstrtobool(buf, &ncq_prio_enable))
 		return -EINVAL;
 
-	if (!scsih_ncq_prio_supp(sdev))
+	if (!sas_ata_ncq_prio_supported(sdev))
 		return -EINVAL;
 
 	sas_device_priv_data->ncq_prio_enable = ncq_prio_enable;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -3670,6 +3670,7 @@
 		fw_event = list_first_entry(&ioc->fw_event_list,
 				struct fw_event_work, list);
 		list_del_init(&fw_event->list);
+		fw_event_work_put(fw_event);
 	}
 	spin_unlock_irqrestore(&ioc->fw_event_lock, flags);
 
@@ -3751,7 +3752,6 @@
 		if (cancel_work_sync(&fw_event->work))
 			fw_event_work_put(fw_event);
 
-		fw_event_work_put(fw_event);
 	}
 	ioc->fw_events_cleanup = 0;
 }
@@ -3869,7 +3869,7 @@
 
 	shost_for_each_device(sdev, ioc->shost) {
 		sas_device_priv_data = sdev->hostdata;
-		if (!sas_device_priv_data)
+		if (!sas_device_priv_data || !sas_device_priv_data->sas_target)
 			continue;
 		if (sas_device_priv_data->sas_target->sas_address
 		    != sas_address)
@@ -6406,11 +6406,26 @@
 	int i, j, count = 0, lcount = 0;
 	int ret;
 	u64 sas_addr;
+	u8 num_phys;
 
 	drsprintk(ioc, ioc_info(ioc,
 	    "updating ports for sas_host(0x%016llx)\n",
 	    (unsigned long long)ioc->sas_hba.sas_address));
 
+	mpt3sas_config_get_number_hba_phys(ioc, &num_phys);
+	if (!num_phys) {
+		ioc_err(ioc, "failure at %s:%d/%s()!\n",
+		    __FILE__, __LINE__, __func__);
+		return;
+	}
+
+	if (num_phys > ioc->sas_hba.nr_phys_allocated) {
+		ioc_err(ioc, "failure at %s:%d/%s()!\n",
+		   __FILE__, __LINE__, __func__);
+		return;
+	}
+	ioc->sas_hba.num_phys = num_phys;
+
 	port_table = kcalloc(ioc->sas_hba.num_phys,
 	    sizeof(struct hba_port), GFP_KERNEL);
 	if (!port_table)
@@ -6611,6 +6626,30 @@
 			ioc->sas_hba.phy[i].hba_vphy = 1;
 		}
 
+		/*
+		 * Add new HBA phys to STL if these new phys got added as part
+		 * of HBA Firmware upgrade/downgrade operation.
+		 */
+		if (!ioc->sas_hba.phy[i].phy) {
+			if ((mpt3sas_config_get_phy_pg0(ioc, &mpi_reply,
+							&phy_pg0, i))) {
+				ioc_err(ioc, "failure at %s:%d/%s()!\n",
+					__FILE__, __LINE__, __func__);
+				continue;
+			}
+			ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+				MPI2_IOCSTATUS_MASK;
+			if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+				ioc_err(ioc, "failure at %s:%d/%s()!\n",
+					__FILE__, __LINE__, __func__);
+				continue;
+			}
+			ioc->sas_hba.phy[i].phy_id = i;
+			mpt3sas_transport_add_host_phy(ioc,
+				&ioc->sas_hba.phy[i], phy_pg0,
+				ioc->sas_hba.parent_dev);
+			continue;
+		}
 		ioc->sas_hba.phy[i].handle = ioc->sas_hba.handle;
 		attached_handle = le16_to_cpu(sas_iounit_pg0->PhyData[i].
 		    AttachedDevHandle);
@@ -6622,6 +6661,19 @@
 		    attached_handle, i, link_rate,
 		    ioc->sas_hba.phy[i].port);
 	}
+	/*
+	 * Clear the phy details if this phy got disabled as part of
+	 * HBA Firmware upgrade/downgrade operation.
+	 */
+	for (i = ioc->sas_hba.num_phys;
+	     i < ioc->sas_hba.nr_phys_allocated; i++) {
+		if (ioc->sas_hba.phy[i].phy &&
+		    ioc->sas_hba.phy[i].phy->negotiated_linkrate >=
+		    SAS_LINK_RATE_1_5_GBPS)
+			mpt3sas_transport_update_links(ioc,
+				ioc->sas_hba.sas_address, 0, i,
+				MPI2_SAS_NEG_LINK_RATE_PHY_DISABLED, NULL);
+	}
  out:
 	kfree(sas_iounit_pg0);
 }
@@ -6654,7 +6706,10 @@
 			__FILE__, __LINE__, __func__);
 		return;
 	}
-	ioc->sas_hba.phy = kcalloc(num_phys,
+
+	ioc->sas_hba.nr_phys_allocated = max_t(u8,
+	    MPT_MAX_HBA_NUM_PHYS, num_phys);
+	ioc->sas_hba.phy = kcalloc(ioc->sas_hba.nr_phys_allocated,
 	    sizeof(struct _sas_phy), GFP_KERNEL);
 	if (!ioc->sas_hba.phy) {
 		ioc_err(ioc, "failure at %s:%d/%s()!\n",
@@ -10980,6 +11035,7 @@
 {
 	struct _sas_port *mpt3sas_port, *next;
 	unsigned long flags;
+	int port_id;
 
 	/* remove sibling ports attached to this expander */
 	list_for_each_entry_safe(mpt3sas_port, next,
@@ -11000,6 +11056,8 @@
 			    mpt3sas_port->hba_port);
 	}
 
+	port_id = sas_expander->port->port_id;
+
 	mpt3sas_transport_port_remove(ioc, sas_expander->sas_address,
 	    sas_expander->sas_address_parent, sas_expander->port);
 
@@ -11007,7 +11065,7 @@
 	    "expander_remove: handle(0x%04x), sas_addr(0x%016llx), port:%d\n",
 	    sas_expander->handle, (unsigned long long)
 	    sas_expander->sas_address,
-	    sas_expander->port->port_id);
+	    port_id);
 
 	spin_lock_irqsave(&ioc->sas_node_lock, flags);
 	list_del(&sas_expander->list);
@@ -11328,6 +11386,7 @@
 	_scsih_ir_shutdown(ioc);
 	_scsih_nvme_shutdown(ioc);
 	mpt3sas_base_mask_interrupts(ioc);
+	mpt3sas_base_stop_watchdog(ioc);
 	ioc->shost_recovery = 1;
 	mpt3sas_base_make_ioc_ready(ioc, SOFT_RESET);
 	ioc->shost_recovery = 0;
@@ -12521,31 +12580,6 @@
 	return PCI_ERS_RESULT_RECOVERED;
 }
 
-/**
- * scsih_ncq_prio_supp - Check for NCQ command priority support
- * @sdev: scsi device struct
- *
- * This is called when a user indicates they would like to enable
- * ncq command priorities. This works only on SATA devices.
- */
-bool scsih_ncq_prio_supp(struct scsi_device *sdev)
-{
-	unsigned char *buf;
-	bool ncq_prio_supp = false;
-
-	if (!scsi_device_supports_vpd(sdev))
-		return ncq_prio_supp;
-
-	buf = kmalloc(SCSI_VPD_PG_LEN, GFP_KERNEL);
-	if (!buf)
-		return ncq_prio_supp;
-
-	if (!scsi_get_vpd_page(sdev, 0x89, buf, SCSI_VPD_PG_LEN))
-		ncq_prio_supp = (buf[213] >> 4) & 1;
-
-	kfree(buf);
-	return ncq_prio_supp;
-}
 /*
  * The pci device ids are defined in mpi/mpi2_cnfg.h.
  */
@@ -12840,8 +12874,10 @@
 	mpt3sas_ctl_init(hbas_to_enumerate);
 
 	error = pci_register_driver(&mpt3sas_driver);
-	if (error)
+	if (error) {
+		mpt3sas_ctl_exit(hbas_to_enumerate);
 		scsih_exit();
+	}
 
 	return error;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mpt3sas/mpt3sas_transport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mpt3sas/mpt3sas_transport.c
@@ -785,7 +785,7 @@
 		goto out_fail;
 	}
 	port = sas_port_alloc_num(sas_node->parent_dev);
-	if ((sas_port_add(port))) {
+	if (!port || (sas_port_add(port))) {
 		ioc_err(ioc, "failure at %s:%d/%s()!\n",
 			__FILE__, __LINE__, __func__);
 		goto out_fail;
@@ -824,11 +824,20 @@
 			    mpt3sas_port->remote_identify.sas_address;
 	}
 
+	if (!rphy) {
+		ioc_err(ioc, "failure at %s:%d/%s()!\n",
+			__FILE__, __LINE__, __func__);
+		goto out_delete_port;
+	}
+
 	rphy->identify = mpt3sas_port->remote_identify;
 
 	if ((sas_rphy_add(rphy))) {
 		ioc_err(ioc, "failure at %s:%d/%s()!\n",
 			__FILE__, __LINE__, __func__);
+		sas_rphy_free(rphy);
+		rphy = NULL;
+		goto out_delete_port;
 	}
 
 	if (mpt3sas_port->remote_identify.device_type == SAS_END_DEVICE) {
@@ -855,7 +864,10 @@
 		    rphy_to_expander_device(rphy), hba_port->port_id);
 	return mpt3sas_port;
 
- out_fail:
+out_delete_port:
+	sas_port_delete(port);
+
+out_fail:
 	list_for_each_entry_safe(mpt3sas_phy, next, &mpt3sas_port->phy_list,
 	    port_siblings)
 		list_del(&mpt3sas_phy->port_siblings);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/mvsas/mv_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/mvsas/mv_init.c
@@ -646,6 +646,7 @@
 	{ PCI_VDEVICE(ARECA, PCI_DEVICE_ID_ARECA_1300), chip_1300 },
 	{ PCI_VDEVICE(ARECA, PCI_DEVICE_ID_ARECA_1320), chip_1320 },
 	{ PCI_VDEVICE(ADAPTEC2, 0x0450), chip_6440 },
+	{ PCI_VDEVICE(TTI, 0x2640), chip_6440 },
 	{ PCI_VDEVICE(TTI, 0x2710), chip_9480 },
 	{ PCI_VDEVICE(TTI, 0x2720), chip_9480 },
 	{ PCI_VDEVICE(TTI, 0x2721), chip_9480 },
@@ -696,7 +697,7 @@
 static ssize_t driver_version_show(struct device *cdev,
 				   struct device_attribute *attr, char *buffer)
 {
-	return snprintf(buffer, PAGE_SIZE, "%s\n", DRV_VERSION);
+	return sysfs_emit(buffer, "%s\n", DRV_VERSION);
 }
 
 static DEVICE_ATTR_RO(driver_version);
@@ -744,7 +745,7 @@
 static ssize_t interrupt_coalescing_show(struct device *cdev,
 					 struct device_attribute *attr, char *buffer)
 {
-	return snprintf(buffer, PAGE_SIZE, "%d\n", interrupt_coalescing);
+	return sysfs_emit(buffer, "%d\n", interrupt_coalescing);
 }
 
 static DEVICE_ATTR_RW(interrupt_coalescing);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/myrb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/myrb.c
@@ -1239,7 +1239,8 @@
 	myrb_unmap(cb);
 
 	if (cb->mmio_base) {
-		cb->disable_intr(cb->io_base);
+		if (cb->disable_intr)
+			cb->disable_intr(cb->io_base);
 		iounmap(cb->mmio_base);
 	}
 	if (cb->irq)
@@ -1774,9 +1775,9 @@
 
 		name = myrb_devstate_name(ldev_info->state);
 		if (name)
-			ret = snprintf(buf, 32, "%s\n", name);
+			ret = snprintf(buf, 64, "%s\n", name);
 		else
-			ret = snprintf(buf, 32, "Invalid (%02X)\n",
+			ret = snprintf(buf, 64, "Invalid (%02X)\n",
 				       ldev_info->state);
 	} else {
 		struct myrb_pdev_state *pdev_info = sdev->hostdata;
@@ -1795,9 +1796,9 @@
 		else
 			name = myrb_devstate_name(pdev_info->state);
 		if (name)
-			ret = snprintf(buf, 32, "%s\n", name);
+			ret = snprintf(buf, 64, "%s\n", name);
 		else
-			ret = snprintf(buf, 32, "Invalid (%02X)\n",
+			ret = snprintf(buf, 64, "Invalid (%02X)\n",
 				       pdev_info->state);
 	}
 	return ret;
@@ -1885,11 +1886,11 @@
 
 		name = myrb_raidlevel_name(ldev_info->raid_level);
 		if (!name)
-			return snprintf(buf, 32, "Invalid (%02X)\n",
+			return snprintf(buf, 64, "Invalid (%02X)\n",
 					ldev_info->state);
-		return snprintf(buf, 32, "%s\n", name);
+		return snprintf(buf, 64, "%s\n", name);
 	}
-	return snprintf(buf, 32, "Physical Drive\n");
+	return snprintf(buf, 64, "Physical Drive\n");
 }
 static DEVICE_ATTR_RO(raid_level);
 
@@ -1902,15 +1903,15 @@
 	unsigned char status;
 
 	if (sdev->channel < myrb_logical_channel(sdev->host))
-		return snprintf(buf, 32, "physical device - not rebuilding\n");
+		return snprintf(buf, 64, "physical device - not rebuilding\n");
 
 	status = myrb_get_rbld_progress(cb, &rbld_buf);
 
 	if (rbld_buf.ldev_num != sdev->id ||
 	    status != MYRB_STATUS_SUCCESS)
-		return snprintf(buf, 32, "not rebuilding\n");
+		return snprintf(buf, 64, "not rebuilding\n");
 
-	return snprintf(buf, 32, "rebuilding block %u of %u\n",
+	return snprintf(buf, 64, "rebuilding block %u of %u\n",
 			rbld_buf.ldev_size - rbld_buf.blocks_left,
 			rbld_buf.ldev_size);
 }
@@ -3409,9 +3410,13 @@
 	mutex_init(&cb->dcmd_mutex);
 	mutex_init(&cb->dma_mutex);
 	cb->pdev = pdev;
+	cb->host = shost;
 
-	if (pci_enable_device(pdev))
-		goto failure;
+	if (pci_enable_device(pdev)) {
+		dev_err(&pdev->dev, "Failed to enable PCI device\n");
+		scsi_host_put(shost);
+		return NULL;
+	}
 
 	if (privdata->hw_init == DAC960_PD_hw_init ||
 	    privdata->hw_init == DAC960_P_hw_init) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/myrs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/myrs.c
@@ -949,9 +949,9 @@
 
 		name = myrs_devstate_name(ldev_info->dev_state);
 		if (name)
-			ret = snprintf(buf, 32, "%s\n", name);
+			ret = snprintf(buf, 64, "%s\n", name);
 		else
-			ret = snprintf(buf, 32, "Invalid (%02X)\n",
+			ret = snprintf(buf, 64, "Invalid (%02X)\n",
 				       ldev_info->dev_state);
 	} else {
 		struct myrs_pdev_info *pdev_info;
@@ -960,9 +960,9 @@
 		pdev_info = sdev->hostdata;
 		name = myrs_devstate_name(pdev_info->dev_state);
 		if (name)
-			ret = snprintf(buf, 32, "%s\n", name);
+			ret = snprintf(buf, 64, "%s\n", name);
 		else
-			ret = snprintf(buf, 32, "Invalid (%02X)\n",
+			ret = snprintf(buf, 64, "Invalid (%02X)\n",
 				       pdev_info->dev_state);
 	}
 	return ret;
@@ -1068,13 +1068,13 @@
 		ldev_info = sdev->hostdata;
 		name = myrs_raid_level_name(ldev_info->raid_level);
 		if (!name)
-			return snprintf(buf, 32, "Invalid (%02X)\n",
+			return snprintf(buf, 64, "Invalid (%02X)\n",
 					ldev_info->dev_state);
 
 	} else
 		name = myrs_raid_level_name(MYRS_RAID_PHYSICAL);
 
-	return snprintf(buf, 32, "%s\n", name);
+	return snprintf(buf, 64, "%s\n", name);
 }
 static DEVICE_ATTR_RO(raid_level);
 
@@ -1088,7 +1088,7 @@
 	unsigned char status;
 
 	if (sdev->channel < cs->ctlr_info->physchan_present)
-		return snprintf(buf, 32, "physical device - not rebuilding\n");
+		return snprintf(buf, 64, "physical device - not rebuilding\n");
 
 	ldev_info = sdev->hostdata;
 	ldev_num = ldev_info->ldev_num;
@@ -1100,11 +1100,11 @@
 		return -EIO;
 	}
 	if (ldev_info->rbld_active) {
-		return snprintf(buf, 32, "rebuilding block %zu of %zu\n",
+		return snprintf(buf, 64, "rebuilding block %zu of %zu\n",
 				(size_t)ldev_info->rbld_lba,
 				(size_t)ldev_info->cfg_devsize);
 	} else
-		return snprintf(buf, 32, "not rebuilding\n");
+		return snprintf(buf, 64, "not rebuilding\n");
 }
 
 static ssize_t rebuild_store(struct device *dev,
@@ -1192,7 +1192,7 @@
 	unsigned short ldev_num;
 
 	if (sdev->channel < cs->ctlr_info->physchan_present)
-		return snprintf(buf, 32, "physical device - not checking\n");
+		return snprintf(buf, 64, "physical device - not checking\n");
 
 	ldev_info = sdev->hostdata;
 	if (!ldev_info)
@@ -1200,11 +1200,11 @@
 	ldev_num = ldev_info->ldev_num;
 	myrs_get_ldev_info(cs, ldev_num, ldev_info);
 	if (ldev_info->cc_active)
-		return snprintf(buf, 32, "checking block %zu of %zu\n",
+		return snprintf(buf, 64, "checking block %zu of %zu\n",
 				(size_t)ldev_info->cc_lba,
 				(size_t)ldev_info->cfg_devsize);
 	else
-		return snprintf(buf, 32, "not checking\n");
+		return snprintf(buf, 64, "not checking\n");
 }
 
 static ssize_t consistency_check_store(struct device *dev,
@@ -2265,7 +2265,8 @@
 	myrs_unmap(cs);
 
 	if (cs->mmio_base) {
-		cs->disable_intr(cs);
+		if (cs->disable_intr)
+			cs->disable_intr(cs);
 		iounmap(cs->mmio_base);
 		cs->mmio_base = NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pm8001/pm8001_hwi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pm8001/pm8001_hwi.c
@@ -1325,7 +1325,9 @@
 	int q_index = circularQ - pm8001_ha->inbnd_q_tbl;
 	int rv;
 
-	WARN_ON(q_index >= PM8001_MAX_INB_NUM);
+	if (WARN_ON(q_index >= pm8001_ha->max_q_num))
+		return -EINVAL;
+
 	spin_lock_irqsave(&circularQ->iq_lock, flags);
 	rv = pm8001_mpi_msg_free_get(circularQ, pm8001_ha->iomb_size,
 			&pMessage);
@@ -1765,7 +1767,6 @@
 	}
 
 	task = sas_alloc_slow_task(GFP_ATOMIC);
-
 	if (!task) {
 		pm8001_dbg(pm8001_ha, FAIL, "cannot allocate task\n");
 		return;
@@ -1774,13 +1775,16 @@
 	task->task_done = pm8001_task_done;
 
 	res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
-	if (res)
+	if (res) {
+		sas_free_task(task);
 		return;
+	}
 
 	ccb = &pm8001_ha->ccb_info[ccb_tag];
 	ccb->device = pm8001_ha_dev;
 	ccb->ccb_tag = ccb_tag;
 	ccb->task = task;
+	ccb->n_elem = 0;
 
 	circularQ = &pm8001_ha->inbnd_q_tbl[0];
 
@@ -1791,8 +1795,10 @@
 
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort,
 			sizeof(task_abort), 0);
-	if (ret)
+	if (ret) {
+		sas_free_task(task);
 		pm8001_tag_free(pm8001_ha, ccb_tag);
+	}
 
 }
 
@@ -1842,6 +1848,7 @@
 	ccb->device = pm8001_ha_dev;
 	ccb->ccb_tag = ccb_tag;
 	ccb->task = task;
+	ccb->n_elem = 0;
 	pm8001_ha_dev->id |= NCQ_READ_LOG_FLAG;
 	pm8001_ha_dev->id |= NCQ_2ND_RLE_FLAG;
 
@@ -1858,7 +1865,7 @@
 
 	sata_cmd.tag = cpu_to_le32(ccb_tag);
 	sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
-	sata_cmd.ncqtag_atap_dir_m |= ((0x1 << 7) | (0x5 << 9));
+	sata_cmd.ncqtag_atap_dir_m = cpu_to_le32((0x1 << 7) | (0x5 << 9));
 	memcpy(&sata_cmd.sata_fis, &fis, sizeof(struct host_to_dev_fis));
 
 	res = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd,
@@ -2419,7 +2426,8 @@
 				len = sizeof(struct pio_setup_fis);
 				pm8001_dbg(pm8001_ha, IO,
 					   "PIO read len = %d\n", len);
-			} else if (t->ata_task.use_ncq) {
+			} else if (t->ata_task.use_ncq &&
+				   t->data_dir != DMA_NONE) {
 				len = sizeof(struct set_dev_bits_fis);
 				pm8001_dbg(pm8001_ha, IO, "FPDMA len = %d\n",
 					   len);
@@ -2693,7 +2701,6 @@
 	u32 tag = le32_to_cpu(psataPayload->tag);
 	u32 port_id = le32_to_cpu(psataPayload->port_id);
 	u32 dev_id = le32_to_cpu(psataPayload->device_id);
-	unsigned long flags;
 
 	ccb = &pm8001_ha->ccb_info[tag];
 
@@ -2733,8 +2740,6 @@
 		ts->resp = SAS_TASK_COMPLETE;
 		ts->stat = SAS_DATA_OVERRUN;
 		ts->residual = 0;
-		if (pm8001_dev)
-			atomic_dec(&pm8001_dev->running_req);
 		break;
 	case IO_XFER_ERROR_BREAK:
 		pm8001_dbg(pm8001_ha, IO, "IO_XFER_ERROR_BREAK\n");
@@ -2776,7 +2781,6 @@
 				IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
 			ts->resp = SAS_TASK_COMPLETE;
 			ts->stat = SAS_QUEUE_FULL;
-			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
 			return;
 		}
 		break;
@@ -2862,20 +2866,6 @@
 		ts->stat = SAS_OPEN_TO;
 		break;
 	}
-	spin_lock_irqsave(&t->task_state_lock, flags);
-	t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
-	t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
-	t->task_state_flags |= SAS_TASK_STATE_DONE;
-	if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
-		spin_unlock_irqrestore(&t->task_state_lock, flags);
-		pm8001_dbg(pm8001_ha, FAIL,
-			   "task 0x%p done with io_status 0x%x resp 0x%x stat 0x%x but aborted by upper layer!\n",
-			   t, event, ts->resp, ts->stat);
-		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
-	} else {
-		spin_unlock_irqrestore(&t->task_state_lock, flags);
-		pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
-	}
 }
 
 /*See the comments for mpi_ssp_completion */
@@ -3169,7 +3159,7 @@
 	 * fw_control_context->usrAddr
 	 */
 	complete(pm8001_ha->nvmd_completion);
-	pm8001_dbg(pm8001_ha, MSG, "Set nvm data complete!\n");
+	pm8001_dbg(pm8001_ha, MSG, "Get nvmd data complete!\n");
 	ccb->task = NULL;
 	ccb->ccb_tag = 0xFFFFFFFF;
 	pm8001_tag_free(pm8001_ha, tag);
@@ -3726,12 +3716,11 @@
 	mb();
 
 	if (pm8001_dev->id & NCQ_ABORT_ALL_FLAG) {
-		pm8001_tag_free(pm8001_ha, tag);
 		sas_free_task(t);
-		/* clear the flag */
-		pm8001_dev->id &= 0xBFFFFFFF;
-	} else
+		pm8001_dev->id &= ~NCQ_ABORT_ALL_FLAG;
+	} else {
 		t->task_done(t);
+	}
 
 	return 0;
 }
@@ -4294,22 +4283,22 @@
 	u32  opc = OPC_INB_SATA_HOST_OPSTART;
 	memset(&sata_cmd, 0, sizeof(sata_cmd));
 	circularQ = &pm8001_ha->inbnd_q_tbl[0];
-	if (task->data_dir == DMA_NONE) {
+
+	if (task->data_dir == DMA_NONE && !task->ata_task.use_ncq) {
 		ATAP = 0x04;  /* no data*/
 		pm8001_dbg(pm8001_ha, IO, "no data\n");
 	} else if (likely(!task->ata_task.device_control_reg_update)) {
-		if (task->ata_task.dma_xfer) {
+		if (task->ata_task.use_ncq &&
+		    dev->sata_dev.class != ATA_DEV_ATAPI) {
+			ATAP = 0x07; /* FPDMA */
+			pm8001_dbg(pm8001_ha, IO, "FPDMA\n");
+		} else if (task->ata_task.dma_xfer) {
 			ATAP = 0x06; /* DMA */
 			pm8001_dbg(pm8001_ha, IO, "DMA\n");
 		} else {
 			ATAP = 0x05; /* PIO*/
 			pm8001_dbg(pm8001_ha, IO, "PIO\n");
 		}
-		if (task->ata_task.use_ncq &&
-			dev->sata_dev.class != ATA_DEV_ATAPI) {
-			ATAP = 0x07; /* FPDMA */
-			pm8001_dbg(pm8001_ha, IO, "FPDMA\n");
-		}
 	}
 	if (task->ata_task.use_ncq && pm8001_get_ncq_tag(task, &hdr_tag)) {
 		task->ata_task.fis.sector_count |= (u8) (hdr_tag << 3);
@@ -4413,7 +4402,7 @@
 	payload.sas_identify.dev_type = SAS_END_DEVICE;
 	payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
 	memcpy(payload.sas_identify.sas_addr,
-		pm8001_ha->sas_addr, SAS_ADDR_SIZE);
+		&pm8001_ha->phy[phy_id].dev_sas_addr, SAS_ADDR_SIZE);
 	payload.sas_identify.phy_id = phy_id;
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload,
 			sizeof(payload), 0);
@@ -4499,6 +4488,9 @@
 		SAS_ADDR_SIZE);
 	rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
 			sizeof(payload), 0);
+	if (rc)
+		pm8001_tag_free(pm8001_ha, tag);
+
 	return rc;
 }
 
@@ -4649,7 +4641,7 @@
 	memcpy(sspTMCmd.lun, task->ssp_task.LUN, 8);
 	sspTMCmd.tag = cpu_to_le32(ccb->ccb_tag);
 	if (pm8001_ha->chip_id != chip_8001)
-		sspTMCmd.ds_ads_m = 0x08;
+		sspTMCmd.ds_ads_m = cpu_to_le32(0x08);
 	circularQ = &pm8001_ha->inbnd_q_tbl[0];
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sspTMCmd,
 			sizeof(sspTMCmd), 0);
@@ -4911,6 +4903,11 @@
 	ccb->ccb_tag = tag;
 	rc = pm8001_chip_fw_flash_update_build(pm8001_ha, &flash_update_info,
 		tag);
+	if (rc) {
+		kfree(fw_control_context);
+		pm8001_tag_free(pm8001_ha, tag);
+	}
+
 	return rc;
 }
 
@@ -5015,6 +5012,9 @@
 	payload.nds = cpu_to_le32(state);
 	rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
 			sizeof(payload), 0);
+	if (rc)
+		pm8001_tag_free(pm8001_ha, tag);
+
 	return rc;
 
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pm8001/pm8001_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pm8001/pm8001_init.c
@@ -255,7 +255,6 @@
 	return ret;
 }
 
-static u32 pm8001_setup_irq(struct pm8001_hba_info *pm8001_ha);
 static u32 pm8001_request_irq(struct pm8001_hba_info *pm8001_ha);
 
 /**
@@ -276,17 +275,10 @@
 	pm8001_dbg(pm8001_ha, INIT, "pm8001_alloc: PHY:%x\n",
 		   pm8001_ha->chip->n_phy);
 
-	/* Setup Interrupt */
-	rc = pm8001_setup_irq(pm8001_ha);
-	if (rc) {
-		pm8001_dbg(pm8001_ha, FAIL,
-			   "pm8001_setup_irq failed [ret: %d]\n", rc);
-		goto err_out_shost;
-	}
 	/* Request Interrupt */
 	rc = pm8001_request_irq(pm8001_ha);
 	if (rc)
-		goto err_out_shost;
+		goto err_out;
 
 	count = pm8001_ha->max_q_num;
 	/* Queues are chosen based on the number of cores/msix availability */
@@ -422,8 +414,6 @@
 	pm8001_tag_init(pm8001_ha);
 	return 0;
 
-err_out_shost:
-	scsi_remove_host(pm8001_ha->shost);
 err_out_nodev:
 	for (i = 0; i < pm8001_ha->max_memcnt; i++) {
 		if (pm8001_ha->memoryMap.region[i].virt_ptr != NULL) {
@@ -1004,47 +994,38 @@
 }
 #endif
 
-static u32 pm8001_setup_irq(struct pm8001_hba_info *pm8001_ha)
-{
-	struct pci_dev *pdev;
-
-	pdev = pm8001_ha->pdev;
-
-#ifdef PM8001_USE_MSIX
-	if (pci_find_capability(pdev, PCI_CAP_ID_MSIX))
-		return pm8001_setup_msix(pm8001_ha);
-	pm8001_dbg(pm8001_ha, INIT, "MSIX not supported!!!\n");
-#endif
-	return 0;
-}
-
 /**
  * pm8001_request_irq - register interrupt
  * @pm8001_ha: our ha struct.
  */
 static u32 pm8001_request_irq(struct pm8001_hba_info *pm8001_ha)
 {
-	struct pci_dev *pdev;
+	struct pci_dev *pdev = pm8001_ha->pdev;
+#ifdef PM8001_USE_MSIX
 	int rc;
 
-	pdev = pm8001_ha->pdev;
+	if (pci_find_capability(pdev, PCI_CAP_ID_MSIX)) {
+		rc = pm8001_setup_msix(pm8001_ha);
+		if (rc) {
+			pm8001_dbg(pm8001_ha, FAIL,
+				   "pm8001_setup_irq failed [ret: %d]\n", rc);
+			return rc;
+		}
 
-#ifdef PM8001_USE_MSIX
-	if (pdev->msix_cap && pci_msi_enabled())
-		return pm8001_request_msix(pm8001_ha);
-	else {
-		pm8001_dbg(pm8001_ha, INIT, "MSIX not supported!!!\n");
-		goto intx;
+		if (pdev->msix_cap && pci_msi_enabled())
+			return pm8001_request_msix(pm8001_ha);
 	}
+
+	pm8001_dbg(pm8001_ha, INIT, "MSIX not supported!!!\n");
 #endif
 
-intx:
 	/* initialize the INT-X interrupt */
 	pm8001_ha->irq_vector[0].irq_id = 0;
 	pm8001_ha->irq_vector[0].drv_inst = pm8001_ha;
-	rc = request_irq(pdev->irq, pm8001_interrupt_handler_intx, IRQF_SHARED,
-		pm8001_ha->name, SHOST_TO_SAS_HA(pm8001_ha->shost));
-	return rc;
+
+	return request_irq(pdev->irq, pm8001_interrupt_handler_intx,
+			   IRQF_SHARED, pm8001_ha->name,
+			   SHOST_TO_SAS_HA(pm8001_ha->shost));
 }
 
 /**
@@ -1198,6 +1179,7 @@
 		goto err_out;
 
 	/* Memory region for ccb_info*/
+	pm8001_ha->ccb_count = ccb_count;
 	pm8001_ha->ccb_info =
 		kcalloc(ccb_count, sizeof(struct pm8001_ccb_info), GFP_KERNEL);
 	if (!pm8001_ha->ccb_info) {
@@ -1259,6 +1241,16 @@
 			tasklet_kill(&pm8001_ha->tasklet[j]);
 #endif
 	scsi_host_put(pm8001_ha->shost);
+
+	for (i = 0; i < pm8001_ha->ccb_count; i++) {
+		dma_free_coherent(&pm8001_ha->pdev->dev,
+			sizeof(struct pm8001_prd) * PM8001_MAX_DMA_SG,
+			pm8001_ha->ccb_info[i].buf_prd,
+			pm8001_ha->ccb_info[i].ccb_dma_handle);
+	}
+	kfree(pm8001_ha->ccb_info);
+	kfree(pm8001_ha->devices);
+
 	pm8001_free(pm8001_ha);
 	kfree(sha->sas_phy);
 	kfree(sha->sas_port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pm8001/pm8001_sas.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pm8001/pm8001_sas.c
@@ -753,8 +753,13 @@
 		res = -TMF_RESP_FUNC_FAILED;
 		/* Even TMF timed out, return direct. */
 		if (task->task_state_flags & SAS_TASK_STATE_ABORTED) {
+			struct pm8001_ccb_info *ccb = task->lldd_task;
+
 			pm8001_dbg(pm8001_ha, FAIL, "TMF task[%x]timeout.\n",
 				   tmf->tmf);
+
+			if (ccb)
+				ccb->task = NULL;
 			goto ex_err;
 		}
 
@@ -826,10 +831,10 @@
 
 		res = PM8001_CHIP_DISP->task_abort(pm8001_ha,
 			pm8001_dev, flag, task_tag, ccb_tag);
-
 		if (res) {
 			del_timer(&task->slow_task->timer);
 			pm8001_dbg(pm8001_ha, FAIL, "Executing internal task failed\n");
+			pm8001_tag_free(pm8001_ha, ccb_tag);
 			goto ex_err;
 		}
 		wait_for_completion(&task->slow_task->completion);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pm8001/pm8001_sas.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pm8001/pm8001_sas.h
@@ -457,6 +457,7 @@
 	__le32			producer_index;
 	u32			consumer_idx;
 	spinlock_t		oq_lock;
+	unsigned long		lock_flags;
 };
 struct pm8001_hba_memspace {
 	void __iomem  		*memvirtaddr;
@@ -516,6 +517,7 @@
 	u32			iomb_size; /* SPC and SPCV IOMB size */
 	struct pm8001_device	*devices;
 	struct pm8001_ccb_info	*ccb_info;
+	u32			ccb_count;
 #ifdef PM8001_USE_MSIX
 	int			number_of_intr;/*will be used in remove()*/
 	char			intr_drvname[PM8001_MAX_MSIX_VEC]
@@ -738,9 +740,7 @@
 {
 	pm8001_ccb_task_free(pm8001_ha, task, ccb, ccb_idx);
 	smp_mb(); /*in order to force CPU ordering*/
-	spin_unlock(&pm8001_ha->lock);
 	task->task_done(task);
-	spin_lock(&pm8001_ha->lock);
 }
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pm8001/pm80xx_hwi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -66,18 +66,16 @@
 }
 
 static void pm80xx_pci_mem_copy(struct pm8001_hba_info  *pm8001_ha, u32 soffset,
-				const void *destination,
+				__le32 *destination,
 				u32 dw_count, u32 bus_base_number)
 {
 	u32 index, value, offset;
-	u32 *destination1;
-	destination1 = (u32 *)destination;
 
-	for (index = 0; index < dw_count; index += 4, destination1++) {
+	for (index = 0; index < dw_count; index += 4, destination++) {
 		offset = (soffset + index);
 		if (offset < (64 * 1024)) {
 			value = pm8001_cr32(pm8001_ha, bus_base_number, offset);
-			*destination1 =  cpu_to_le32(value);
+			*destination = cpu_to_le32(value);
 		}
 	}
 	return;
@@ -767,6 +765,10 @@
 	pm8001_ha->main_cfg_tbl.pm80xx_tbl.pcs_event_log_severity	= 0x01;
 	pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_interrupt		= 0x01;
 
+	/* Enable higher IQs and OQs, 32 to 63, bit 16 */
+	if (pm8001_ha->max_q_num > 32)
+		pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_interrupt |=
+							1 << 16;
 	/* Disable end to end CRC checking */
 	pm8001_ha->main_cfg_tbl.pm80xx_tbl.crc_core_dump = (0x1 << 16);
 
@@ -1028,6 +1030,13 @@
 	if (0x0000 != gst_len_mpistate)
 		return -EBUSY;
 
+	/*
+	 *  As per controller datasheet, after successful MPI
+	 *  initialization minimum 500ms delay is required before
+	 *  issuing commands.
+	 */
+	msleep(500);
+
 	return 0;
 }
 
@@ -1202,9 +1211,11 @@
 	else
 		page_code = THERMAL_PAGE_CODE_8H;
 
-	payload.cfg_pg[0] = (THERMAL_LOG_ENABLE << 9) |
-				(THERMAL_ENABLE << 8) | page_code;
-	payload.cfg_pg[1] = (LTEMPHIL << 24) | (RTEMPHIL << 8);
+	payload.cfg_pg[0] =
+		cpu_to_le32((THERMAL_LOG_ENABLE << 9) |
+			    (THERMAL_ENABLE << 8) | page_code);
+	payload.cfg_pg[1] =
+		cpu_to_le32((LTEMPHIL << 24) | (RTEMPHIL << 8));
 
 	pm8001_dbg(pm8001_ha, DEV,
 		   "Setting up thermal config. cfg_pg 0 0x%x cfg_pg 1 0x%x\n",
@@ -1244,43 +1255,41 @@
 	circularQ = &pm8001_ha->inbnd_q_tbl[0];
 	payload.tag = cpu_to_le32(tag);
 
-	SASConfigPage.pageCode        =  SAS_PROTOCOL_TIMER_CONFIG_PAGE;
-	SASConfigPage.MST_MSI         =  3 << 15;
-	SASConfigPage.STP_SSP_MCT_TMO =  (STP_MCT_TMO << 16) | SSP_MCT_TMO;
-	SASConfigPage.STP_FRM_TMO     = (SAS_MAX_OPEN_TIME << 24) |
-				(SMP_MAX_CONN_TIMER << 16) | STP_FRM_TIMER;
-	SASConfigPage.STP_IDLE_TMO    =  STP_IDLE_TIME;
-
-	if (SASConfigPage.STP_IDLE_TMO > 0x3FFFFFF)
-		SASConfigPage.STP_IDLE_TMO = 0x3FFFFFF;
-
-
-	SASConfigPage.OPNRJT_RTRY_INTVL =         (SAS_MFD << 16) |
-						SAS_OPNRJT_RTRY_INTVL;
-	SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO =  (SAS_DOPNRJT_RTRY_TMO << 16)
-						| SAS_COPNRJT_RTRY_TMO;
-	SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR =  (SAS_DOPNRJT_RTRY_THR << 16)
-						| SAS_COPNRJT_RTRY_THR;
-	SASConfigPage.MAX_AIP =  SAS_MAX_AIP;
+	SASConfigPage.pageCode = cpu_to_le32(SAS_PROTOCOL_TIMER_CONFIG_PAGE);
+	SASConfigPage.MST_MSI = cpu_to_le32(3 << 15);
+	SASConfigPage.STP_SSP_MCT_TMO =
+		cpu_to_le32((STP_MCT_TMO << 16) | SSP_MCT_TMO);
+	SASConfigPage.STP_FRM_TMO =
+		cpu_to_le32((SAS_MAX_OPEN_TIME << 24) |
+			    (SMP_MAX_CONN_TIMER << 16) | STP_FRM_TIMER);
+	SASConfigPage.STP_IDLE_TMO = cpu_to_le32(STP_IDLE_TIME);
+
+	SASConfigPage.OPNRJT_RTRY_INTVL =
+		cpu_to_le32((SAS_MFD << 16) | SAS_OPNRJT_RTRY_INTVL);
+	SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO =
+		cpu_to_le32((SAS_DOPNRJT_RTRY_TMO << 16) | SAS_COPNRJT_RTRY_TMO);
+	SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR =
+		cpu_to_le32((SAS_DOPNRJT_RTRY_THR << 16) | SAS_COPNRJT_RTRY_THR);
+	SASConfigPage.MAX_AIP = cpu_to_le32(SAS_MAX_AIP);
 
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.pageCode 0x%08x\n",
-		   SASConfigPage.pageCode);
+		   le32_to_cpu(SASConfigPage.pageCode));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.MST_MSI  0x%08x\n",
-		   SASConfigPage.MST_MSI);
+		   le32_to_cpu(SASConfigPage.MST_MSI));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.STP_SSP_MCT_TMO  0x%08x\n",
-		   SASConfigPage.STP_SSP_MCT_TMO);
+		   le32_to_cpu(SASConfigPage.STP_SSP_MCT_TMO));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.STP_FRM_TMO  0x%08x\n",
-		   SASConfigPage.STP_FRM_TMO);
+		   le32_to_cpu(SASConfigPage.STP_FRM_TMO));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.STP_IDLE_TMO  0x%08x\n",
-		   SASConfigPage.STP_IDLE_TMO);
+		   le32_to_cpu(SASConfigPage.STP_IDLE_TMO));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.OPNRJT_RTRY_INTVL  0x%08x\n",
-		   SASConfigPage.OPNRJT_RTRY_INTVL);
+		   le32_to_cpu(SASConfigPage.OPNRJT_RTRY_INTVL));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO  0x%08x\n",
-		   SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO);
+		   le32_to_cpu(SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR  0x%08x\n",
-		   SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR);
+		   le32_to_cpu(SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR));
 	pm8001_dbg(pm8001_ha, INIT, "SASConfigPage.MAX_AIP  0x%08x\n",
-		   SASConfigPage.MAX_AIP);
+		   le32_to_cpu(SASConfigPage.MAX_AIP));
 
 	memcpy(&payload.cfg_pg, &SASConfigPage,
 			 sizeof(SASProtocolTimerConfig_t));
@@ -1406,12 +1415,13 @@
 	/* Currently only one key is used. New KEK index is 1.
 	 * Current KEK index is 1. Store KEK to NVRAM is 1.
 	 */
-	payload.new_curidx_ksop = ((1 << 24) | (1 << 16) | (1 << 8) |
-					KEK_MGMT_SUBOP_KEYCARDUPDATE);
+	payload.new_curidx_ksop =
+		cpu_to_le32(((1 << 24) | (1 << 16) | (1 << 8) |
+			     KEK_MGMT_SUBOP_KEYCARDUPDATE));
 
 	pm8001_dbg(pm8001_ha, DEV,
 		   "Saving Encryption info to flash. payload 0x%x\n",
-		   payload.new_curidx_ksop);
+		   le32_to_cpu(payload.new_curidx_ksop));
 
 	rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
 			sizeof(payload), 0);
@@ -1734,10 +1744,11 @@
 pm80xx_chip_interrupt_enable(struct pm8001_hba_info *pm8001_ha, u8 vec)
 {
 #ifdef PM8001_USE_MSIX
-	u32 mask;
-	mask = (u32)(1 << vec);
-
-	pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_CLR, (u32)(mask & 0xFFFFFFFF));
+	if (vec < 32)
+		pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_CLR, 1U << vec);
+	else
+		pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_CLR_U,
+			    1U << (vec - 32));
 	return;
 #endif
 	pm80xx_chip_intx_interrupt_enable(pm8001_ha);
@@ -1753,12 +1764,15 @@
 pm80xx_chip_interrupt_disable(struct pm8001_hba_info *pm8001_ha, u8 vec)
 {
 #ifdef PM8001_USE_MSIX
-	u32 mask;
-	if (vec == 0xFF)
-		mask = 0xFFFFFFFF;
+	if (vec == 0xFF) {
+		/* disable all vectors 0-31, 32-63 */
+		pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, 0xFFFFFFFF);
+		pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_U, 0xFFFFFFFF);
+	} else if (vec < 32)
+		pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, 1U << vec);
 	else
-		mask = (u32)(1 << vec);
-	pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, (u32)(mask & 0xFFFFFFFF));
+		pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_U,
+			    1U << (vec - 32));
 	return;
 #endif
 	pm80xx_chip_intx_interrupt_disable(pm8001_ha);
@@ -1800,6 +1814,7 @@
 	ccb->device = pm8001_ha_dev;
 	ccb->ccb_tag = ccb_tag;
 	ccb->task = task;
+	ccb->n_elem = 0;
 
 	circularQ = &pm8001_ha->inbnd_q_tbl[0];
 
@@ -1881,7 +1896,7 @@
 
 	sata_cmd.tag = cpu_to_le32(ccb_tag);
 	sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
-	sata_cmd.ncqtag_atap_dir_m_dad |= ((0x1 << 7) | (0x5 << 9));
+	sata_cmd.ncqtag_atap_dir_m_dad = cpu_to_le32(((0x1 << 7) | (0x5 << 9)));
 	memcpy(&sata_cmd.sata_fis, &fis, sizeof(struct host_to_dev_fis));
 
 	res = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd,
@@ -2184,9 +2199,9 @@
 		pm8001_dbg(pm8001_ha, FAIL,
 			   "task 0x%p done with io_status 0x%x resp 0x%x stat 0x%x but aborted by upper layer!\n",
 			   t, status, ts->resp, ts->stat);
+		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
 		if (t->slow_task)
 			complete(&t->slow_task->completion);
-		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
 	} else {
 		spin_unlock_irqrestore(&t->task_state_lock, flags);
 		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
@@ -2379,7 +2394,8 @@
 
 /*See the comments for mpi_ssp_completion */
 static void
-mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
+mpi_sata_completion(struct pm8001_hba_info *pm8001_ha,
+		struct outbound_queue_table *circularQ, void *piomb)
 {
 	struct sas_task *t;
 	struct pm8001_ccb_info *ccb;
@@ -2516,7 +2532,8 @@
 				len = sizeof(struct pio_setup_fis);
 				pm8001_dbg(pm8001_ha, IO,
 					   "PIO read len = %d\n", len);
-			} else if (t->ata_task.use_ncq) {
+			} else if (t->ata_task.use_ncq &&
+				   t->data_dir != DMA_NONE) {
 				len = sizeof(struct set_dev_bits_fis);
 				pm8001_dbg(pm8001_ha, IO, "FPDMA len = %d\n",
 					   len);
@@ -2616,7 +2633,11 @@
 				IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
 			ts->resp = SAS_TASK_UNDELIVERED;
 			ts->stat = SAS_QUEUE_FULL;
+			spin_unlock_irqrestore(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
+			spin_lock_irqsave(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			return;
 		}
 		break;
@@ -2632,7 +2653,11 @@
 				IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
 			ts->resp = SAS_TASK_UNDELIVERED;
 			ts->stat = SAS_QUEUE_FULL;
+			spin_unlock_irqrestore(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
+			spin_lock_irqsave(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			return;
 		}
 		break;
@@ -2656,7 +2681,11 @@
 				IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY);
 			ts->resp = SAS_TASK_UNDELIVERED;
 			ts->stat = SAS_QUEUE_FULL;
+			spin_unlock_irqrestore(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
+			spin_lock_irqsave(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			return;
 		}
 		break;
@@ -2727,7 +2756,11 @@
 					IO_DS_NON_OPERATIONAL);
 			ts->resp = SAS_TASK_UNDELIVERED;
 			ts->stat = SAS_QUEUE_FULL;
+			spin_unlock_irqrestore(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
+			spin_lock_irqsave(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			return;
 		}
 		break;
@@ -2747,7 +2780,11 @@
 					IO_DS_IN_ERROR);
 			ts->resp = SAS_TASK_UNDELIVERED;
 			ts->stat = SAS_QUEUE_FULL;
+			spin_unlock_irqrestore(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
+			spin_lock_irqsave(&circularQ->oq_lock,
+					circularQ->lock_flags);
 			return;
 		}
 		break;
@@ -2780,17 +2817,22 @@
 		pm8001_dbg(pm8001_ha, FAIL,
 			   "task 0x%p done with io_status 0x%x resp 0x%x stat 0x%x but aborted by upper layer!\n",
 			   t, status, ts->resp, ts->stat);
+		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
 		if (t->slow_task)
 			complete(&t->slow_task->completion);
-		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
 	} else {
 		spin_unlock_irqrestore(&t->task_state_lock, flags);
+		spin_unlock_irqrestore(&circularQ->oq_lock,
+				circularQ->lock_flags);
 		pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
+		spin_lock_irqsave(&circularQ->oq_lock,
+				circularQ->lock_flags);
 	}
 }
 
 /*See the comments for mpi_ssp_completion */
-static void mpi_sata_event(struct pm8001_hba_info *pm8001_ha, void *piomb)
+static void mpi_sata_event(struct pm8001_hba_info *pm8001_ha,
+		struct outbound_queue_table *circularQ, void *piomb)
 {
 	struct sas_task *t;
 	struct task_status_struct *ts;
@@ -2802,7 +2844,6 @@
 	u32 tag = le32_to_cpu(psataPayload->tag);
 	u32 port_id = le32_to_cpu(psataPayload->port_id);
 	u32 dev_id = le32_to_cpu(psataPayload->device_id);
-	unsigned long flags;
 
 	ccb = &pm8001_ha->ccb_info[tag];
 
@@ -2840,8 +2881,6 @@
 		ts->resp = SAS_TASK_COMPLETE;
 		ts->stat = SAS_DATA_OVERRUN;
 		ts->residual = 0;
-		if (pm8001_dev)
-			atomic_dec(&pm8001_dev->running_req);
 		break;
 	case IO_XFER_ERROR_BREAK:
 		pm8001_dbg(pm8001_ha, IO, "IO_XFER_ERROR_BREAK\n");
@@ -2890,7 +2929,6 @@
 				IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
 			ts->resp = SAS_TASK_COMPLETE;
 			ts->stat = SAS_QUEUE_FULL;
-			pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
 			return;
 		}
 		break;
@@ -2990,20 +3028,6 @@
 		ts->stat = SAS_OPEN_TO;
 		break;
 	}
-	spin_lock_irqsave(&t->task_state_lock, flags);
-	t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
-	t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
-	t->task_state_flags |= SAS_TASK_STATE_DONE;
-	if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
-		spin_unlock_irqrestore(&t->task_state_lock, flags);
-		pm8001_dbg(pm8001_ha, FAIL,
-			   "task 0x%p done with io_status 0x%x resp 0x%x stat 0x%x but aborted by upper layer!\n",
-			   t, event, ts->resp, ts->stat);
-		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
-	} else {
-		spin_unlock_irqrestore(&t->task_state_lock, flags);
-		pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
-	}
 }
 
 /*See the comments for mpi_ssp_completion */
@@ -3769,10 +3793,12 @@
 			(struct set_ctrl_cfg_resp *)(piomb + 4);
 	u32 status = le32_to_cpu(pPayload->status);
 	u32 err_qlfr_pgcd = le32_to_cpu(pPayload->err_qlfr_pgcd);
+	u32 tag = le32_to_cpu(pPayload->tag);
 
 	pm8001_dbg(pm8001_ha, MSG,
 		   "SET CONTROLLER RESP: status 0x%x qlfr_pgcd 0x%x\n",
 		   status, err_qlfr_pgcd);
+	pm8001_tag_free(pm8001_ha, tag);
 
 	return 0;
 }
@@ -3902,7 +3928,8 @@
  * @pm8001_ha: our hba card information
  * @piomb: IO message buffer
  */
-static void process_one_iomb(struct pm8001_hba_info *pm8001_ha, void *piomb)
+static void process_one_iomb(struct pm8001_hba_info *pm8001_ha,
+		struct outbound_queue_table *circularQ, void *piomb)
 {
 	__le32 pHeader = *(__le32 *)piomb;
 	u32 opc = (u32)((le32_to_cpu(pHeader)) & 0xFFF);
@@ -3944,11 +3971,11 @@
 		break;
 	case OPC_OUB_SATA_COMP:
 		pm8001_dbg(pm8001_ha, MSG, "OPC_OUB_SATA_COMP\n");
-		mpi_sata_completion(pm8001_ha, piomb);
+		mpi_sata_completion(pm8001_ha, circularQ, piomb);
 		break;
 	case OPC_OUB_SATA_EVENT:
 		pm8001_dbg(pm8001_ha, MSG, "OPC_OUB_SATA_EVENT\n");
-		mpi_sata_event(pm8001_ha, piomb);
+		mpi_sata_event(pm8001_ha, circularQ, piomb);
 		break;
 	case OPC_OUB_SSP_EVENT:
 		pm8001_dbg(pm8001_ha, MSG, "OPC_OUB_SSP_EVENT\n");
@@ -4117,13 +4144,24 @@
 	void *pMsg1 = NULL;
 	u8 bc;
 	u32 ret = MPI_IO_STATUS_FAIL;
-	unsigned long flags;
 	u32 regval;
 
+	/*
+	 * Fatal errors are programmed to be signalled in irq vector
+	 * pm8001_ha->max_q_num - 1 through pm8001_ha->main_cfg_tbl.pm80xx_tbl.
+	 * fatal_err_interrupt
+	 */
 	if (vec == (pm8001_ha->max_q_num - 1)) {
+		u32 mipsall_ready;
+
+		if (pm8001_ha->chip_id == chip_8008 ||
+		    pm8001_ha->chip_id == chip_8009)
+			mipsall_ready = SCRATCH_PAD_MIPSALL_READY_8PORT;
+		else
+			mipsall_ready = SCRATCH_PAD_MIPSALL_READY_16PORT;
+
 		regval = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
-		if ((regval & SCRATCH_PAD_MIPSALL_READY) !=
-					SCRATCH_PAD_MIPSALL_READY) {
+		if ((regval & mipsall_ready) != mipsall_ready) {
 			pm8001_ha->controller_fatal_error = true;
 			pm8001_dbg(pm8001_ha, FAIL,
 				   "Firmware Fatal error! Regval:0x%x\n",
@@ -4134,7 +4172,7 @@
 		}
 	}
 	circularQ = &pm8001_ha->outbnd_q_tbl[vec];
-	spin_lock_irqsave(&circularQ->oq_lock, flags);
+	spin_lock_irqsave(&circularQ->oq_lock, circularQ->lock_flags);
 	do {
 		/* spurious interrupt during setup if kexec-ing and
 		 * driver doing a doorbell access w/ the pre-kexec oq
@@ -4145,7 +4183,8 @@
 		ret = pm8001_mpi_msg_consume(pm8001_ha, circularQ, &pMsg1, &bc);
 		if (MPI_IO_STATUS_SUCCESS == ret) {
 			/* process the outbound message */
-			process_one_iomb(pm8001_ha, (void *)(pMsg1 - 4));
+			process_one_iomb(pm8001_ha, circularQ,
+						(void *)(pMsg1 - 4));
 			/* free the message from the outbound circular buffer */
 			pm8001_mpi_msg_free_set(pm8001_ha, pMsg1,
 							circularQ, bc);
@@ -4160,7 +4199,7 @@
 				break;
 		}
 	} while (1);
-	spin_unlock_irqrestore(&circularQ->oq_lock, flags);
+	spin_unlock_irqrestore(&circularQ->oq_lock, circularQ->lock_flags);
 	return ret;
 }
 
@@ -4359,13 +4398,15 @@
 	struct ssp_ini_io_start_req ssp_cmd;
 	u32 tag = ccb->ccb_tag;
 	int ret;
-	u64 phys_addr, start_addr, end_addr;
+	u64 phys_addr, end_addr;
 	u32 end_addr_high, end_addr_low;
 	struct inbound_queue_table *circularQ;
 	u32 q_index, cpu_id;
 	u32 opc = OPC_INB_SSPINIIOSTART;
+
 	memset(&ssp_cmd, 0, sizeof(ssp_cmd));
 	memcpy(ssp_cmd.ssp_iu.lun, task->ssp_task.LUN, 8);
+
 	/* data address domain added for spcv; set to 0 by host,
 	 * used internally by controller
 	 * 0 for SAS 1.1 and SAS 2.0 compatible TLR
@@ -4376,7 +4417,7 @@
 	ssp_cmd.device_id = cpu_to_le32(pm8001_dev->device_id);
 	ssp_cmd.tag = cpu_to_le32(tag);
 	if (task->ssp_task.enable_first_burst)
-		ssp_cmd.ssp_iu.efb_prio_attr |= 0x80;
+		ssp_cmd.ssp_iu.efb_prio_attr = 0x80;
 	ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_prio << 3);
 	ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_attr & 7);
 	memcpy(ssp_cmd.ssp_iu.cdb, task->ssp_task.cmd->cmnd,
@@ -4408,21 +4449,24 @@
 			ssp_cmd.enc_esgl = cpu_to_le32(1<<31);
 		} else if (task->num_scatter == 1) {
 			u64 dma_addr = sg_dma_address(task->scatter);
+
 			ssp_cmd.enc_addr_low =
 				cpu_to_le32(lower_32_bits(dma_addr));
 			ssp_cmd.enc_addr_high =
 				cpu_to_le32(upper_32_bits(dma_addr));
 			ssp_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
 			ssp_cmd.enc_esgl = 0;
+
 			/* Check 4G Boundary */
-			start_addr = cpu_to_le64(dma_addr);
-			end_addr = (start_addr + ssp_cmd.enc_len) - 1;
-			end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
-			end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
-			if (end_addr_high != ssp_cmd.enc_addr_high) {
+			end_addr = dma_addr + le32_to_cpu(ssp_cmd.enc_len) - 1;
+			end_addr_low = lower_32_bits(end_addr);
+			end_addr_high = upper_32_bits(end_addr);
+
+			if (end_addr_high != le32_to_cpu(ssp_cmd.enc_addr_high)) {
 				pm8001_dbg(pm8001_ha, FAIL,
 					   "The sg list address start_addr=0x%016llx data_len=0x%x end_addr_high=0x%08x end_addr_low=0x%08x has crossed 4G boundary\n",
-					   start_addr, ssp_cmd.enc_len,
+					   dma_addr,
+					   le32_to_cpu(ssp_cmd.enc_len),
 					   end_addr_high, end_addr_low);
 				pm8001_chip_make_sg(task->scatter, 1,
 					ccb->buf_prd);
@@ -4431,7 +4475,7 @@
 					cpu_to_le32(lower_32_bits(phys_addr));
 				ssp_cmd.enc_addr_high =
 					cpu_to_le32(upper_32_bits(phys_addr));
-				ssp_cmd.enc_esgl = cpu_to_le32(1<<31);
+				ssp_cmd.enc_esgl = cpu_to_le32(1U<<31);
 			}
 		} else if (task->num_scatter == 0) {
 			ssp_cmd.enc_addr_low = 0;
@@ -4439,8 +4483,10 @@
 			ssp_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
 			ssp_cmd.enc_esgl = 0;
 		}
+
 		/* XTS mode. All other fields are 0 */
-		ssp_cmd.key_cmode = 0x6 << 4;
+		ssp_cmd.key_cmode = cpu_to_le32(0x6 << 4);
+
 		/* set tweak values. Should be the start lba */
 		ssp_cmd.twk_val0 = cpu_to_le32((task->ssp_task.cmd->cmnd[2] << 24) |
 						(task->ssp_task.cmd->cmnd[3] << 16) |
@@ -4462,20 +4508,22 @@
 			ssp_cmd.esgl = cpu_to_le32(1<<31);
 		} else if (task->num_scatter == 1) {
 			u64 dma_addr = sg_dma_address(task->scatter);
+
 			ssp_cmd.addr_low = cpu_to_le32(lower_32_bits(dma_addr));
 			ssp_cmd.addr_high =
 				cpu_to_le32(upper_32_bits(dma_addr));
 			ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
 			ssp_cmd.esgl = 0;
+
 			/* Check 4G Boundary */
-			start_addr = cpu_to_le64(dma_addr);
-			end_addr = (start_addr + ssp_cmd.len) - 1;
-			end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
-			end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
-			if (end_addr_high != ssp_cmd.addr_high) {
+			end_addr = dma_addr + le32_to_cpu(ssp_cmd.len) - 1;
+			end_addr_low = lower_32_bits(end_addr);
+			end_addr_high = upper_32_bits(end_addr);
+			if (end_addr_high != le32_to_cpu(ssp_cmd.addr_high)) {
 				pm8001_dbg(pm8001_ha, FAIL,
 					   "The sg list address start_addr=0x%016llx data_len=0x%x end_addr_high=0x%08x end_addr_low=0x%08x has crossed 4G boundary\n",
-					   start_addr, ssp_cmd.len,
+					   dma_addr,
+					   le32_to_cpu(ssp_cmd.len),
 					   end_addr_high, end_addr_low);
 				pm8001_chip_make_sg(task->scatter, 1,
 					ccb->buf_prd);
@@ -4509,7 +4557,7 @@
 	u32 q_index, cpu_id;
 	struct sata_start_req sata_cmd;
 	u32 hdr_tag, ncg_tag = 0;
-	u64 phys_addr, start_addr, end_addr;
+	u64 phys_addr, end_addr;
 	u32 end_addr_high, end_addr_low;
 	u32 ATAP = 0x0;
 	u32 dir;
@@ -4521,22 +4569,21 @@
 	q_index = (u32) (cpu_id) % (pm8001_ha->max_q_num);
 	circularQ = &pm8001_ha->inbnd_q_tbl[q_index];
 
-	if (task->data_dir == DMA_NONE) {
+	if (task->data_dir == DMA_NONE && !task->ata_task.use_ncq) {
 		ATAP = 0x04; /* no data*/
 		pm8001_dbg(pm8001_ha, IO, "no data\n");
 	} else if (likely(!task->ata_task.device_control_reg_update)) {
-		if (task->ata_task.dma_xfer) {
+		if (task->ata_task.use_ncq &&
+		    dev->sata_dev.class != ATA_DEV_ATAPI) {
+			ATAP = 0x07; /* FPDMA */
+			pm8001_dbg(pm8001_ha, IO, "FPDMA\n");
+		} else if (task->ata_task.dma_xfer) {
 			ATAP = 0x06; /* DMA */
 			pm8001_dbg(pm8001_ha, IO, "DMA\n");
 		} else {
 			ATAP = 0x05; /* PIO*/
 			pm8001_dbg(pm8001_ha, IO, "PIO\n");
 		}
-		if (task->ata_task.use_ncq &&
-		    dev->sata_dev.class != ATA_DEV_ATAPI) {
-			ATAP = 0x07; /* FPDMA */
-			pm8001_dbg(pm8001_ha, IO, "FPDMA\n");
-		}
 	}
 	if (task->ata_task.use_ncq && pm8001_get_ncq_tag(task, &hdr_tag)) {
 		task->ata_task.fis.sector_count |= (u8) (hdr_tag << 3);
@@ -4570,32 +4617,38 @@
 			pm8001_chip_make_sg(task->scatter,
 						ccb->n_elem, ccb->buf_prd);
 			phys_addr = ccb->ccb_dma_handle;
-			sata_cmd.enc_addr_low = lower_32_bits(phys_addr);
-			sata_cmd.enc_addr_high = upper_32_bits(phys_addr);
+			sata_cmd.enc_addr_low =
+				cpu_to_le32(lower_32_bits(phys_addr));
+			sata_cmd.enc_addr_high =
+				cpu_to_le32(upper_32_bits(phys_addr));
 			sata_cmd.enc_esgl = cpu_to_le32(1 << 31);
 		} else if (task->num_scatter == 1) {
 			u64 dma_addr = sg_dma_address(task->scatter);
-			sata_cmd.enc_addr_low = lower_32_bits(dma_addr);
-			sata_cmd.enc_addr_high = upper_32_bits(dma_addr);
+
+			sata_cmd.enc_addr_low =
+				cpu_to_le32(lower_32_bits(dma_addr));
+			sata_cmd.enc_addr_high =
+				cpu_to_le32(upper_32_bits(dma_addr));
 			sata_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
 			sata_cmd.enc_esgl = 0;
+
 			/* Check 4G Boundary */
-			start_addr = cpu_to_le64(dma_addr);
-			end_addr = (start_addr + sata_cmd.enc_len) - 1;
-			end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
-			end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
-			if (end_addr_high != sata_cmd.enc_addr_high) {
+			end_addr = dma_addr + le32_to_cpu(sata_cmd.enc_len) - 1;
+			end_addr_low = lower_32_bits(end_addr);
+			end_addr_high = upper_32_bits(end_addr);
+			if (end_addr_high != le32_to_cpu(sata_cmd.enc_addr_high)) {
 				pm8001_dbg(pm8001_ha, FAIL,
 					   "The sg list address start_addr=0x%016llx data_len=0x%x end_addr_high=0x%08x end_addr_low=0x%08x has crossed 4G boundary\n",
-					   start_addr, sata_cmd.enc_len,
+					   dma_addr,
+					   le32_to_cpu(sata_cmd.enc_len),
 					   end_addr_high, end_addr_low);
 				pm8001_chip_make_sg(task->scatter, 1,
 					ccb->buf_prd);
 				phys_addr = ccb->ccb_dma_handle;
 				sata_cmd.enc_addr_low =
-					lower_32_bits(phys_addr);
+					cpu_to_le32(lower_32_bits(phys_addr));
 				sata_cmd.enc_addr_high =
-					upper_32_bits(phys_addr);
+					cpu_to_le32(upper_32_bits(phys_addr));
 				sata_cmd.enc_esgl =
 					cpu_to_le32(1 << 31);
 			}
@@ -4606,7 +4659,8 @@
 			sata_cmd.enc_esgl = 0;
 		}
 		/* XTS mode. All other fields are 0 */
-		sata_cmd.key_index_mode = 0x6 << 4;
+		sata_cmd.key_index_mode = cpu_to_le32(0x6 << 4);
+
 		/* set tweak values. Should be the start lba */
 		sata_cmd.twk_val0 =
 			cpu_to_le32((sata_cmd.sata_fis.lbal_exp << 24) |
@@ -4632,31 +4686,31 @@
 			phys_addr = ccb->ccb_dma_handle;
 			sata_cmd.addr_low = lower_32_bits(phys_addr);
 			sata_cmd.addr_high = upper_32_bits(phys_addr);
-			sata_cmd.esgl = cpu_to_le32(1 << 31);
+			sata_cmd.esgl = cpu_to_le32(1U << 31);
 		} else if (task->num_scatter == 1) {
 			u64 dma_addr = sg_dma_address(task->scatter);
+
 			sata_cmd.addr_low = lower_32_bits(dma_addr);
 			sata_cmd.addr_high = upper_32_bits(dma_addr);
 			sata_cmd.len = cpu_to_le32(task->total_xfer_len);
 			sata_cmd.esgl = 0;
+
 			/* Check 4G Boundary */
-			start_addr = cpu_to_le64(dma_addr);
-			end_addr = (start_addr + sata_cmd.len) - 1;
-			end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
-			end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
+			end_addr = dma_addr + le32_to_cpu(sata_cmd.len) - 1;
+			end_addr_low = lower_32_bits(end_addr);
+			end_addr_high = upper_32_bits(end_addr);
 			if (end_addr_high != sata_cmd.addr_high) {
 				pm8001_dbg(pm8001_ha, FAIL,
 					   "The sg list address start_addr=0x%016llx data_len=0x%xend_addr_high=0x%08x end_addr_low=0x%08x has crossed 4G boundary\n",
-					   start_addr, sata_cmd.len,
+					   dma_addr,
+					   le32_to_cpu(sata_cmd.len),
 					   end_addr_high, end_addr_low);
 				pm8001_chip_make_sg(task->scatter, 1,
 					ccb->buf_prd);
 				phys_addr = ccb->ccb_dma_handle;
-				sata_cmd.addr_low =
-					lower_32_bits(phys_addr);
-				sata_cmd.addr_high =
-					upper_32_bits(phys_addr);
-				sata_cmd.esgl = cpu_to_le32(1 << 31);
+				sata_cmd.addr_low = lower_32_bits(phys_addr);
+				sata_cmd.addr_high = upper_32_bits(phys_addr);
+				sata_cmd.esgl = cpu_to_le32(1U << 31);
 			}
 		} else if (task->num_scatter == 0) {
 			sata_cmd.addr_low = 0;
@@ -4664,27 +4718,28 @@
 			sata_cmd.len = cpu_to_le32(task->total_xfer_len);
 			sata_cmd.esgl = 0;
 		}
+
 		/* scsi cdb */
 		sata_cmd.atapi_scsi_cdb[0] =
 			cpu_to_le32(((task->ata_task.atapi_packet[0]) |
-			(task->ata_task.atapi_packet[1] << 8) |
-			(task->ata_task.atapi_packet[2] << 16) |
-			(task->ata_task.atapi_packet[3] << 24)));
+				     (task->ata_task.atapi_packet[1] << 8) |
+				     (task->ata_task.atapi_packet[2] << 16) |
+				     (task->ata_task.atapi_packet[3] << 24)));
 		sata_cmd.atapi_scsi_cdb[1] =
 			cpu_to_le32(((task->ata_task.atapi_packet[4]) |
-			(task->ata_task.atapi_packet[5] << 8) |
-			(task->ata_task.atapi_packet[6] << 16) |
-			(task->ata_task.atapi_packet[7] << 24)));
+				     (task->ata_task.atapi_packet[5] << 8) |
+				     (task->ata_task.atapi_packet[6] << 16) |
+				     (task->ata_task.atapi_packet[7] << 24)));
 		sata_cmd.atapi_scsi_cdb[2] =
 			cpu_to_le32(((task->ata_task.atapi_packet[8]) |
-			(task->ata_task.atapi_packet[9] << 8) |
-			(task->ata_task.atapi_packet[10] << 16) |
-			(task->ata_task.atapi_packet[11] << 24)));
+				     (task->ata_task.atapi_packet[9] << 8) |
+				     (task->ata_task.atapi_packet[10] << 16) |
+				     (task->ata_task.atapi_packet[11] << 24)));
 		sata_cmd.atapi_scsi_cdb[3] =
 			cpu_to_le32(((task->ata_task.atapi_packet[12]) |
-			(task->ata_task.atapi_packet[13] << 8) |
-			(task->ata_task.atapi_packet[14] << 16) |
-			(task->ata_task.atapi_packet[15] << 24)));
+				     (task->ata_task.atapi_packet[13] << 8) |
+				     (task->ata_task.atapi_packet[14] << 16) |
+				     (task->ata_task.atapi_packet[15] << 24)));
 	}
 
 	/* Check for read log for failed drive and return */
@@ -4761,7 +4816,7 @@
 	payload.sas_identify.dev_type = SAS_END_DEVICE;
 	payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
 	memcpy(payload.sas_identify.sas_addr,
-	  &pm8001_ha->sas_addr, SAS_ADDR_SIZE);
+		&pm8001_ha->phy[phy_id].dev_sas_addr, SAS_ADDR_SIZE);
 	payload.sas_identify.phy_id = phy_id;
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload,
 			sizeof(payload), 0);
@@ -4882,8 +4937,13 @@
 	payload.tag = cpu_to_le32(tag);
 	payload.phyop_phyid =
 		cpu_to_le32(((phy_op & 0xFF) << 8) | (phyId & 0xFF));
-	return pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
-			sizeof(payload), 0);
+
+	rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
+				  sizeof(payload), 0);
+	if (rc)
+		pm8001_tag_free(pm8001_ha, tag);
+
+	return rc;
 }
 
 static u32 pm80xx_chip_is_our_interrupt(struct pm8001_hba_info *pm8001_ha)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pm8001/pm80xx_hwi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pm8001/pm80xx_hwi.h
@@ -1405,8 +1405,12 @@
 #define SCRATCH_PAD_BOOT_LOAD_SUCCESS	0x0
 #define SCRATCH_PAD_IOP0_READY		0xC00
 #define SCRATCH_PAD_IOP1_READY		0x3000
-#define SCRATCH_PAD_MIPSALL_READY	(SCRATCH_PAD_IOP1_READY | \
+#define SCRATCH_PAD_MIPSALL_READY_16PORT	(SCRATCH_PAD_IOP1_READY | \
 					SCRATCH_PAD_IOP0_READY | \
+					SCRATCH_PAD_ILA_READY | \
+					SCRATCH_PAD_RAAE_READY)
+#define SCRATCH_PAD_MIPSALL_READY_8PORT	(SCRATCH_PAD_IOP0_READY | \
+					SCRATCH_PAD_ILA_READY | \
 					SCRATCH_PAD_RAAE_READY)
 
 /* boot loader state */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/pmcraid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/pmcraid.c
@@ -4526,7 +4526,7 @@
 	return 0;
 
 out_unwind:
-	while (--i > 0)
+	while (--i >= 0)
 		free_irq(pci_irq_vector(pdev, i), &pinstance->hrrq_vector[i]);
 	pci_free_irq_vectors(pdev);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedf/qedf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedf/qedf.h
@@ -354,6 +354,7 @@
 #define QEDF_IN_RECOVERY		5
 #define QEDF_DBG_STOP_IO		6
 #define QEDF_PROBING			8
+#define QEDF_STAG_IN_PROGRESS		9
 	unsigned long flags; /* Miscellaneous state flags */
 	int fipvlan_retries;
 	u8 num_queues;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedf/qedf_dbg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedf/qedf_dbg.h
@@ -59,6 +59,8 @@
 #define QEDF_LOG_NOTICE	0x40000000	/* Notice logs */
 #define QEDF_LOG_WARN		0x80000000	/* Warning logs */
 
+#define QEDF_DEBUGFS_LOG_LEN (2 * PAGE_SIZE)
+
 /* Debug context structure */
 struct qedf_dbg_ctx {
 	unsigned int host_no;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedf/qedf_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedf/qedf_debugfs.c
@@ -8,6 +8,7 @@
 #include <linux/uaccess.h>
 #include <linux/debugfs.h>
 #include <linux/module.h>
+#include <linux/vmalloc.h>
 
 #include "qedf.h"
 #include "qedf_dbg.h"
@@ -98,7 +99,9 @@
 qedf_dbg_fp_int_cmd_read(struct file *filp, char __user *buffer, size_t count,
 			 loff_t *ppos)
 {
+	ssize_t ret;
 	size_t cnt = 0;
+	char *cbuf;
 	int id;
 	struct qedf_fastpath *fp = NULL;
 	struct qedf_dbg_ctx *qedf_dbg =
@@ -108,19 +111,25 @@
 
 	QEDF_INFO(qedf_dbg, QEDF_LOG_DEBUGFS, "entered\n");
 
-	cnt = sprintf(buffer, "\nFastpath I/O completions\n\n");
+	cbuf = vmalloc(QEDF_DEBUGFS_LOG_LEN);
+	if (!cbuf)
+		return 0;
+
+	cnt += scnprintf(cbuf + cnt, QEDF_DEBUGFS_LOG_LEN - cnt, "\nFastpath I/O completions\n\n");
 
 	for (id = 0; id < qedf->num_queues; id++) {
 		fp = &(qedf->fp_array[id]);
 		if (fp->sb_id == QEDF_SB_ID_NULL)
 			continue;
-		cnt += sprintf((buffer + cnt), "#%d: %lu\n", id,
-			       fp->completions);
+		cnt += scnprintf(cbuf + cnt, QEDF_DEBUGFS_LOG_LEN - cnt,
+				 "#%d: %lu\n", id, fp->completions);
 	}
 
-	cnt = min_t(int, count, cnt - *ppos);
-	*ppos += cnt;
-	return cnt;
+	ret = simple_read_from_buffer(buffer, count, ppos, cbuf, cnt);
+
+	vfree(cbuf);
+
+	return ret;
 }
 
 static ssize_t
@@ -138,15 +147,14 @@
 			loff_t *ppos)
 {
 	int cnt;
+	char cbuf[32];
 	struct qedf_dbg_ctx *qedf_dbg =
 				(struct qedf_dbg_ctx *)filp->private_data;
 
 	QEDF_INFO(qedf_dbg, QEDF_LOG_DEBUGFS, "debug mask=0x%x\n", qedf_debug);
-	cnt = sprintf(buffer, "debug mask = 0x%x\n", qedf_debug);
+	cnt = scnprintf(cbuf, sizeof(cbuf), "debug mask = 0x%x\n", qedf_debug);
 
-	cnt = min_t(int, count, cnt - *ppos);
-	*ppos += cnt;
-	return cnt;
+	return simple_read_from_buffer(buffer, count, ppos, cbuf, cnt);
 }
 
 static ssize_t
@@ -162,7 +170,7 @@
 	if (!count || *ppos)
 		return 0;
 
-	kern_buf = memdup_user(buffer, count);
+	kern_buf = memdup_user_nul(buffer, count);
 	if (IS_ERR(kern_buf))
 		return PTR_ERR(kern_buf);
 
@@ -185,18 +193,17 @@
 				   size_t count, loff_t *ppos)
 {
 	int cnt;
+	char cbuf[7];
 	struct qedf_dbg_ctx *qedf_dbg =
 				(struct qedf_dbg_ctx *)filp->private_data;
 	struct qedf_ctx *qedf = container_of(qedf_dbg,
 	    struct qedf_ctx, dbg_ctx);
 
 	QEDF_INFO(qedf_dbg, QEDF_LOG_DEBUGFS, "entered\n");
-	cnt = sprintf(buffer, "%s\n",
+	cnt = scnprintf(cbuf, sizeof(cbuf), "%s\n",
 	    qedf->stop_io_on_error ? "true" : "false");
 
-	cnt = min_t(int, count, cnt - *ppos);
-	*ppos += cnt;
-	return cnt;
+	return simple_read_from_buffer(buffer, count, ppos, cbuf, cnt);
 }
 
 static ssize_t
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedf/qedf_io.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedf/qedf_io.c
@@ -1913,6 +1913,7 @@
 		goto drop_rdata_kref;
 	}
 
+	spin_lock_irqsave(&fcport->rport_lock, flags);
 	if (!test_bit(QEDF_CMD_OUTSTANDING, &io_req->flags) ||
 	    test_bit(QEDF_CMD_IN_CLEANUP, &io_req->flags) ||
 	    test_bit(QEDF_CMD_IN_ABORT, &io_req->flags)) {
@@ -1920,17 +1921,20 @@
 			 "io_req xid=0x%x sc_cmd=%p already in cleanup or abort processing or already completed.\n",
 			 io_req->xid, io_req->sc_cmd);
 		rc = 1;
+		spin_unlock_irqrestore(&fcport->rport_lock, flags);
 		goto drop_rdata_kref;
 	}
 
+	/* Set the command type to abort */
+	io_req->cmd_type = QEDF_ABTS;
+	spin_unlock_irqrestore(&fcport->rport_lock, flags);
+
 	kref_get(&io_req->refcount);
 
 	xid = io_req->xid;
 	qedf->control_requests++;
 	qedf->packet_aborts++;
 
-	/* Set the command type to abort */
-	io_req->cmd_type = QEDF_ABTS;
 	io_req->return_scsi_cmd_on_abts = return_scsi_cmd_on_abts;
 
 	set_bit(QEDF_CMD_IN_ABORT, &io_req->flags);
@@ -2219,7 +2223,9 @@
 		  refcount, fcport, fcport->rdata->ids.port_id);
 
 	/* Cleanup cmds re-use the same TID as the original I/O */
+	spin_lock_irqsave(&fcport->rport_lock, flags);
 	io_req->cmd_type = QEDF_CLEANUP;
+	spin_unlock_irqrestore(&fcport->rport_lock, flags);
 	io_req->return_scsi_cmd_on_abts = return_scsi_cmd_on_abts;
 
 	init_completion(&io_req->cleanup_done);
@@ -2257,6 +2263,7 @@
 	    io_req->tm_flags == FCP_TMF_TGT_RESET) {
 		clear_bit(QEDF_CMD_OUTSTANDING, &io_req->flags);
 		io_req->sc_cmd = NULL;
+		kref_put(&io_req->refcount, qedf_release_cmd);
 		complete(&io_req->tm_done);
 	}
 
@@ -2333,9 +2340,6 @@
 	io_req->fcport = fcport;
 	io_req->cmd_type = QEDF_TASK_MGMT_CMD;
 
-	/* Record which cpu this request is associated with */
-	io_req->cpu = smp_processor_id();
-
 	/* Set TM flags */
 	io_req->io_req_flags = QEDF_READ;
 	io_req->data_xfer_len = 0;
@@ -2357,6 +2361,9 @@
 
 	spin_lock_irqsave(&fcport->rport_lock, flags);
 
+	/* Record which cpu this request is associated with */
+	io_req->cpu = smp_processor_id();
+
 	sqe_idx = qedf_get_sqe_idx(fcport);
 	sqe = &fcport->sq[sqe_idx];
 	memset(sqe, 0, sizeof(struct fcoe_wqe));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedf/qedf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedf/qedf_main.c
@@ -31,6 +31,7 @@
 static void qedf_shutdown(struct pci_dev *pdev);
 static void qedf_schedule_recovery_handler(void *dev);
 static void qedf_recovery_handler(struct work_struct *work);
+static int qedf_suspend(struct pci_dev *pdev, pm_message_t state);
 
 /*
  * Driver module parameters.
@@ -317,11 +318,18 @@
 	 */
 	if (resp == fc_lport_flogi_resp) {
 		qedf->flogi_cnt++;
+		qedf->flogi_pending++;
+
+		if (test_bit(QEDF_UNLOADING, &qedf->flags)) {
+			QEDF_ERR(&qedf->dbg_ctx, "Driver unloading\n");
+			qedf->flogi_pending = 0;
+		}
+
 		if (qedf->flogi_pending >= QEDF_FLOGI_RETRY_CNT) {
 			schedule_delayed_work(&qedf->stag_work, 2);
 			return NULL;
 		}
-		qedf->flogi_pending++;
+
 		return fc_elsct_send(lport, did, fp, op, qedf_flogi_resp,
 		    arg, timeout);
 	}
@@ -910,13 +918,14 @@
 	struct qedf_ctx *qedf;
 	struct qed_link_output if_link;
 
+	qedf = lport_priv(lport);
+
 	if (lport->vport) {
-		QEDF_ERR(NULL, "Cannot issue host reset on NPIV port.\n");
+		clear_bit(QEDF_STAG_IN_PROGRESS, &qedf->flags);
+		printk_ratelimited("Cannot issue host reset on NPIV port.\n");
 		return;
 	}
 
-	qedf = lport_priv(lport);
-
 	qedf->flogi_pending = 0;
 	/* For host reset, essentially do a soft link up/down */
 	atomic_set(&qedf->link_state, QEDF_LINK_DOWN);
@@ -936,6 +945,7 @@
 	if (!if_link.link_up) {
 		QEDF_INFO(&qedf->dbg_ctx, QEDF_LOG_DISC,
 			  "Physical link is not up.\n");
+		clear_bit(QEDF_STAG_IN_PROGRESS, &qedf->flags);
 		return;
 	}
 	/* Flush and wait to make sure link down is processed */
@@ -948,6 +958,7 @@
 		  "Queue link up work.\n");
 	queue_delayed_work(qedf->link_update_wq, &qedf->link_update,
 	    0);
+	clear_bit(QEDF_STAG_IN_PROGRESS, &qedf->flags);
 }
 
 /* Reset the host by gracefully logging out and then logging back in */
@@ -1862,6 +1873,7 @@
 	vport_qedf->cmd_mgr = base_qedf->cmd_mgr;
 	init_completion(&vport_qedf->flogi_compl);
 	INIT_LIST_HEAD(&vport_qedf->fcports);
+	INIT_DELAYED_WORK(&vport_qedf->stag_work, qedf_stag_change_work);
 
 	rc = qedf_vport_libfc_config(vport, vn_port);
 	if (rc) {
@@ -1920,6 +1932,27 @@
 		fc_vport_setlink(vn_port);
 	}
 
+	/* Set symbolic node name */
+	if (base_qedf->pdev->device == QL45xxx)
+		snprintf(fc_host_symbolic_name(vn_port->host), 256,
+			 "Marvell FastLinQ 45xxx FCoE v%s", QEDF_VERSION);
+
+	if (base_qedf->pdev->device == QL41xxx)
+		snprintf(fc_host_symbolic_name(vn_port->host), 256,
+			 "Marvell FastLinQ 41xxx FCoE v%s", QEDF_VERSION);
+
+	/* Set supported speed */
+	fc_host_supported_speeds(vn_port->host) = n_port->link_supported_speeds;
+
+	/* Set speed */
+	vn_port->link_speed = n_port->link_speed;
+
+	/* Set port type */
+	fc_host_port_type(vn_port->host) = FC_PORTTYPE_NPIV;
+
+	/* Set maxframe size */
+	fc_host_maxframe_size(vn_port->host) = n_port->mfs;
+
 	QEDF_INFO(&(base_qedf->dbg_ctx), QEDF_LOG_NPIV, "vn_port=%p.\n",
 		   vn_port);
 
@@ -2706,6 +2739,7 @@
 	    sb_id, QED_SB_TYPE_STORAGE);
 
 	if (ret) {
+		dma_free_coherent(&qedf->pdev->dev, sizeof(*sb_virt), sb_virt, sb_phys);
 		QEDF_ERR(&qedf->dbg_ctx,
 			 "Status block initialization failed (0x%x) for id = %d.\n",
 			 ret, sb_id);
@@ -2784,6 +2818,8 @@
 	struct qedf_ioreq *io_req;
 	struct qedf_rport *fcport;
 	u32 comp_type;
+	u8 io_comp_type;
+	unsigned long flags;
 
 	comp_type = (cqe->cqe_data >> FCOE_CQE_CQE_TYPE_SHIFT) &
 	    FCOE_CQE_CQE_TYPE_MASK;
@@ -2817,11 +2853,14 @@
 		return;
 	}
 
+	spin_lock_irqsave(&fcport->rport_lock, flags);
+	io_comp_type = io_req->cmd_type;
+	spin_unlock_irqrestore(&fcport->rport_lock, flags);
 
 	switch (comp_type) {
 	case FCOE_GOOD_COMPLETION_CQE_TYPE:
 		atomic_inc(&fcport->free_sqes);
-		switch (io_req->cmd_type) {
+		switch (io_comp_type) {
 		case QEDF_SCSI_CMD:
 			qedf_scsi_completion(qedf, cqe, io_req);
 			break;
@@ -3024,9 +3063,8 @@
 	 * addresses of our queues
 	 */
 	if (!qedf->p_cpuq) {
-		status = -EINVAL;
 		QEDF_ERR(&qedf->dbg_ctx, "p_cpuq is NULL.\n");
-		goto mem_alloc_failure;
+		return -EINVAL;
 	}
 
 	qedf->global_queues = kzalloc((sizeof(struct global_queue *)
@@ -3255,6 +3293,7 @@
 	.probe = qedf_probe,
 	.remove = qedf_remove,
 	.shutdown = qedf_shutdown,
+	.suspend = qedf_suspend,
 };
 
 static int __qedf_probe(struct pci_dev *pdev, int mode)
@@ -3416,7 +3455,9 @@
 		qedf->devlink = qed_ops->common->devlink_register(qedf->cdev);
 		if (IS_ERR(qedf->devlink)) {
 			QEDF_ERR(&qedf->dbg_ctx, "Cannot register devlink\n");
+			rc = PTR_ERR(qedf->devlink);
 			qedf->devlink = NULL;
+			goto err2;
 		}
 	}
 
@@ -3437,6 +3478,7 @@
 	}
 
 	/* Start the Slowpath-process */
+	memset(&slowpath_params, 0, sizeof(struct qed_slowpath_params));
 	slowpath_params.int_mode = QED_INT_MODE_MSIX;
 	slowpath_params.drv_major = QEDF_DRIVER_MAJOR_VER;
 	slowpath_params.drv_minor = QEDF_DRIVER_MINOR_VER;
@@ -3683,11 +3725,6 @@
 err1:
 	scsi_host_put(lport->host);
 err0:
-	if (qedf) {
-		QEDF_INFO(&qedf->dbg_ctx, QEDF_LOG_DISC, "Probe done.\n");
-
-		clear_bit(QEDF_PROBING, &qedf->flags);
-	}
 	return rc;
 }
 
@@ -3700,6 +3737,7 @@
 {
 	struct qedf_ctx *qedf;
 	int rc;
+	int cnt = 0;
 
 	if (!pdev) {
 		QEDF_ERR(NULL, "pdev is NULL.\n");
@@ -3717,6 +3755,17 @@
 		return;
 	}
 
+stag_in_prog:
+	if (test_bit(QEDF_STAG_IN_PROGRESS, &qedf->flags)) {
+		QEDF_ERR(&qedf->dbg_ctx, "Stag in progress, cnt=%d.\n", cnt);
+		cnt++;
+
+		if (cnt < 5) {
+			msleep(500);
+			goto stag_in_prog;
+		}
+	}
+
 	if (mode != QEDF_MODE_RECOVERY)
 		set_bit(QEDF_UNLOADING, &qedf->flags);
 
@@ -3976,7 +4025,27 @@
 	struct qedf_ctx *qedf =
 	    container_of(work, struct qedf_ctx, stag_work.work);
 
-	QEDF_ERR(&qedf->dbg_ctx, "Performing software context reset.\n");
+	if (!qedf) {
+		QEDF_ERR(&qedf->dbg_ctx, "qedf is NULL");
+		return;
+	}
+
+	if (test_bit(QEDF_IN_RECOVERY, &qedf->flags)) {
+		QEDF_ERR(&qedf->dbg_ctx,
+			 "Already is in recovery, hence not calling software context reset.\n");
+		return;
+	}
+
+	if (test_bit(QEDF_UNLOADING, &qedf->flags)) {
+		QEDF_ERR(&qedf->dbg_ctx, "Driver unloading\n");
+		return;
+	}
+
+	set_bit(QEDF_STAG_IN_PROGRESS, &qedf->flags);
+
+	printk_ratelimited("[%s]:[%s:%d]:%d: Performing software context reset.",
+			dev_name(&qedf->pdev->dev), __func__, __LINE__,
+			qedf->dbg_ctx.host_no);
 	qedf_ctx_soft_reset(qedf->lport);
 }
 
@@ -3985,6 +4054,22 @@
 	__qedf_remove(pdev, QEDF_MODE_NORMAL);
 }
 
+static int qedf_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct qedf_ctx *qedf;
+
+	if (!pdev) {
+		QEDF_ERR(NULL, "pdev is NULL.\n");
+		return -ENODEV;
+	}
+
+	qedf = pci_get_drvdata(pdev);
+
+	QEDF_ERR(&qedf->dbg_ctx, "%s: Device does not support suspend operation\n", __func__);
+
+	return -EPERM;
+}
+
 /*
  * Recovery handler code
  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedi/qedi_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedi/qedi_debugfs.c
@@ -120,15 +120,11 @@
 qedi_dbg_do_not_recover_cmd_read(struct file *filp, char __user *buffer,
 				 size_t count, loff_t *ppos)
 {
-	size_t cnt = 0;
+	char buf[64];
+	int len;
 
-	if (*ppos)
-		return 0;
-
-	cnt = sprintf(buffer, "do_not_recover=%d\n", qedi_do_not_recover);
-	cnt = min_t(int, count, cnt - *ppos);
-	*ppos += cnt;
-	return cnt;
+	len = sprintf(buf, "do_not_recover=%d\n", qedi_do_not_recover);
+	return simple_read_from_buffer(buffer, count, ppos, buf, len);
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedi/qedi_fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedi/qedi_fw.c
@@ -772,11 +772,10 @@
 			qedi_cmd->list_tmf_work = NULL;
 		}
 	}
+	spin_unlock_bh(&qedi_conn->tmf_work_lock);
 
-	if (!found) {
-		spin_unlock_bh(&qedi_conn->tmf_work_lock);
+	if (!found)
 		goto check_cleanup_reqs;
-	}
 
 	QEDI_INFO(&qedi->dbg_ctx, QEDI_LOG_SCSI_TM,
 		  "TMF work, cqe->tid=0x%x, tmf flags=0x%x, cid=0x%x\n",
@@ -807,7 +806,6 @@
 	qedi_cmd->state = CLEANUP_RECV;
 unlock:
 	spin_unlock_bh(&conn->session->back_lock);
-	spin_unlock_bh(&qedi_conn->tmf_work_lock);
 	wake_up_interruptible(&qedi_conn->wait_queue);
 	return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedi/qedi_iscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedi/qedi_iscsi.c
@@ -859,6 +859,37 @@
 	return qedi_iscsi_send_ioreq(task);
 }
 
+static void qedi_offload_work(struct work_struct *work)
+{
+	struct qedi_endpoint *qedi_ep =
+		container_of(work, struct qedi_endpoint, offload_work);
+	struct qedi_ctx *qedi;
+	int wait_delay = 5 * HZ;
+	int ret;
+
+	qedi = qedi_ep->qedi;
+
+	ret = qedi_iscsi_offload_conn(qedi_ep);
+	if (ret) {
+		QEDI_ERR(&qedi->dbg_ctx,
+			 "offload error: iscsi_cid=%u, qedi_ep=%p, ret=%d\n",
+			 qedi_ep->iscsi_cid, qedi_ep, ret);
+		qedi_ep->state = EP_STATE_OFLDCONN_FAILED;
+		return;
+	}
+
+	ret = wait_event_interruptible_timeout(qedi_ep->tcp_ofld_wait,
+					       (qedi_ep->state ==
+					       EP_STATE_OFLDCONN_COMPL),
+					       wait_delay);
+	if (ret <= 0 || qedi_ep->state != EP_STATE_OFLDCONN_COMPL) {
+		qedi_ep->state = EP_STATE_OFLDCONN_FAILED;
+		QEDI_ERR(&qedi->dbg_ctx,
+			 "Offload conn TIMEOUT iscsi_cid=%u, qedi_ep=%p\n",
+			 qedi_ep->iscsi_cid, qedi_ep);
+	}
+}
+
 static struct iscsi_endpoint *
 qedi_ep_connect(struct Scsi_Host *shost, struct sockaddr *dst_addr,
 		int non_blocking)
@@ -907,6 +938,7 @@
 	}
 	qedi_ep = ep->dd_data;
 	memset(qedi_ep, 0, sizeof(struct qedi_endpoint));
+	INIT_WORK(&qedi_ep->offload_work, qedi_offload_work);
 	qedi_ep->state = EP_STATE_IDLE;
 	qedi_ep->iscsi_cid = (u32)-1;
 	qedi_ep->qedi = qedi;
@@ -1055,12 +1087,11 @@
 	qedi_ep = ep->dd_data;
 	qedi = qedi_ep->qedi;
 
+	flush_work(&qedi_ep->offload_work);
+
 	if (qedi_ep->state == EP_STATE_OFLDCONN_START)
 		goto ep_exit_recover;
 
-	if (qedi_ep->state != EP_STATE_OFLDCONN_NONE)
-		flush_work(&qedi_ep->offload_work);
-
 	if (qedi_ep->conn) {
 		qedi_conn = qedi_ep->conn;
 		abrt_conn = qedi_conn->abrt_conn;
@@ -1234,37 +1265,6 @@
 	return rc;
 }
 
-static void qedi_offload_work(struct work_struct *work)
-{
-	struct qedi_endpoint *qedi_ep =
-		container_of(work, struct qedi_endpoint, offload_work);
-	struct qedi_ctx *qedi;
-	int wait_delay = 5 * HZ;
-	int ret;
-
-	qedi = qedi_ep->qedi;
-
-	ret = qedi_iscsi_offload_conn(qedi_ep);
-	if (ret) {
-		QEDI_ERR(&qedi->dbg_ctx,
-			 "offload error: iscsi_cid=%u, qedi_ep=%p, ret=%d\n",
-			 qedi_ep->iscsi_cid, qedi_ep, ret);
-		qedi_ep->state = EP_STATE_OFLDCONN_FAILED;
-		return;
-	}
-
-	ret = wait_event_interruptible_timeout(qedi_ep->tcp_ofld_wait,
-					       (qedi_ep->state ==
-					       EP_STATE_OFLDCONN_COMPL),
-					       wait_delay);
-	if ((ret <= 0) || (qedi_ep->state != EP_STATE_OFLDCONN_COMPL)) {
-		qedi_ep->state = EP_STATE_OFLDCONN_FAILED;
-		QEDI_ERR(&qedi->dbg_ctx,
-			 "Offload conn TIMEOUT iscsi_cid=%u, qedi_ep=%p\n",
-			 qedi_ep->iscsi_cid, qedi_ep);
-	}
-}
-
 static int qedi_set_path(struct Scsi_Host *shost, struct iscsi_path *path_data)
 {
 	struct qedi_ctx *qedi;
@@ -1380,7 +1380,6 @@
 			  qedi_ep->dst_addr, qedi_ep->dst_port);
 	}
 
-	INIT_WORK(&qedi_ep->offload_work, qedi_offload_work);
 	queue_work(qedi->offload_thread, &qedi_ep->offload_work);
 
 	ret = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qedi/qedi_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qedi/qedi_main.c
@@ -69,6 +69,7 @@
 static void qedi_recovery_handler(struct work_struct *work);
 static void qedi_schedule_hw_err_handler(void *dev,
 					 enum qed_hw_err_type err_type);
+static int qedi_suspend(struct pci_dev *pdev, pm_message_t state);
 
 static int qedi_iscsi_event_cb(void *context, u8 fw_event_code, void *fw_handle)
 {
@@ -368,6 +369,7 @@
 	ret = qedi_ops->common->sb_init(qedi->cdev, sb_info, sb_virt, sb_phys,
 				       sb_id, QED_SB_TYPE_STORAGE);
 	if (ret) {
+		dma_free_coherent(&qedi->pdev->dev, sizeof(*sb_virt), sb_virt, sb_phys);
 		QEDI_ERR(&qedi->dbg_ctx,
 			 "Status block initialization failed for id = %d.\n",
 			  sb_id);
@@ -1978,8 +1980,9 @@
 	struct qedi_percpu_s *p = this_cpu_ptr(&qedi_percpu);
 	struct qedi_work *work, *tmp;
 	struct task_struct *thread;
+	unsigned long flags;
 
-	spin_lock_bh(&p->p_work_lock);
+	spin_lock_irqsave(&p->p_work_lock, flags);
 	thread = p->iothread;
 	p->iothread = NULL;
 
@@ -1990,7 +1993,7 @@
 			kfree(work);
 	}
 
-	spin_unlock_bh(&p->p_work_lock);
+	spin_unlock_irqrestore(&p->p_work_lock, flags);
 	if (thread)
 		kthread_stop(thread);
 	return 0;
@@ -2417,9 +2420,12 @@
 	int rval;
 	u16 retry = 10;
 
-	if (mode == QEDI_MODE_NORMAL || mode == QEDI_MODE_SHUTDOWN) {
-		iscsi_host_remove(qedi->shost);
+	if (mode == QEDI_MODE_NORMAL)
+		iscsi_host_remove(qedi->shost, false);
+	else if (mode == QEDI_MODE_SHUTDOWN)
+		iscsi_host_remove(qedi->shost, true);
 
+	if (mode == QEDI_MODE_NORMAL || mode == QEDI_MODE_SHUTDOWN) {
 		if (qedi->tmf_thread) {
 			flush_workqueue(qedi->tmf_thread);
 			destroy_workqueue(qedi->tmf_thread);
@@ -2452,6 +2458,9 @@
 		qedi_ops->ll2->stop(qedi->cdev);
 	}
 
+	cancel_delayed_work_sync(&qedi->recovery_work);
+	cancel_delayed_work_sync(&qedi->board_disable_work);
+
 	qedi_free_iscsi_pf_param(qedi);
 
 	rval = qedi_ops->common->update_drv_state(qedi->cdev, false);
@@ -2509,6 +2518,22 @@
 	__qedi_remove(pdev, QEDI_MODE_SHUTDOWN);
 }
 
+static int qedi_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct qedi_ctx *qedi;
+
+	if (!pdev) {
+		QEDI_ERR(NULL, "pdev is NULL.\n");
+		return -ENODEV;
+	}
+
+	qedi = pci_get_drvdata(pdev);
+
+	QEDI_ERR(&qedi->dbg_ctx, "%s: Device does not support suspend operation\n", __func__);
+
+	return -EPERM;
+}
+
 static int __qedi_probe(struct pci_dev *pdev, int mode)
 {
 	struct qedi_ctx *qedi;
@@ -2796,7 +2821,7 @@
 #ifdef CONFIG_DEBUG_FS
 	qedi_dbg_host_exit(&qedi->dbg_ctx);
 #endif
-	iscsi_host_remove(qedi->shost);
+	iscsi_host_remove(qedi->shost, false);
 stop_iscsi_func:
 	qedi_ops->stop(qedi->cdev);
 stop_slowpath:
@@ -2867,6 +2892,7 @@
 	.remove = qedi_remove,
 	.shutdown = qedi_shutdown,
 	.err_handler = &qedi_err_handler,
+	.suspend = qedi_suspend,
 };
 
 static int __init qedi_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla1280.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla1280.c
@@ -2875,7 +2875,7 @@
 			dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n",
 				cpu_to_le32(upper_32_bits(dma_handle)),
 				cpu_to_le32(lower_32_bits(dma_handle)),
-				cpu_to_le32(sg_dma_len(sg_next(s))));
+				cpu_to_le32(sg_dma_len(s)));
 			remseg--;
 		}
 		dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather "
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla1280.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla1280.h
@@ -117,12 +117,12 @@
 	uint16_t id_h;		/* ID high */
 	uint16_t cfg_0;		/* Configuration 0 */
 #define ISP_CFG0_HWMSK   0x000f	/* Hardware revision mask */
-#define ISP_CFG0_1020    BIT_0	/* ISP1020 */
-#define ISP_CFG0_1020A	 BIT_1	/* ISP1020A */
-#define ISP_CFG0_1040	 BIT_2	/* ISP1040 */
-#define ISP_CFG0_1040A	 BIT_3	/* ISP1040A */
-#define ISP_CFG0_1040B	 BIT_4	/* ISP1040B */
-#define ISP_CFG0_1040C	 BIT_5	/* ISP1040C */
+#define ISP_CFG0_1020	 1	/* ISP1020 */
+#define ISP_CFG0_1020A	 2	/* ISP1020A */
+#define ISP_CFG0_1040	 3	/* ISP1040 */
+#define ISP_CFG0_1040A	 4	/* ISP1040A */
+#define ISP_CFG0_1040B	 5	/* ISP1040B */
+#define ISP_CFG0_1040C	 6	/* ISP1040C */
 	uint16_t cfg_1;		/* Configuration 1 */
 #define ISP_CFG1_F128    BIT_6  /* 128-byte FIFO threshold */
 #define ISP_CFG1_F64     BIT_4|BIT_5 /* 128-byte FIFO threshold */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_attr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_attr.c
@@ -555,7 +555,7 @@
 	if (!capable(CAP_SYS_ADMIN))
 		return -EINVAL;
 
-	if (IS_NOCACHE_VPD_TYPE(ha))
+	if (!IS_NOCACHE_VPD_TYPE(ha))
 		goto skip;
 
 	faddr = ha->flt_region_vpd << 2;
@@ -745,7 +745,7 @@
 		ql_log(ql_log_info, vha, 0x706f,
 		    "Issuing MPI reset.\n");
 
-		if (IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha)) {
+		if (IS_QLA83XX(ha)) {
 			uint32_t idc_control;
 
 			qla83xx_idc_lock(vha, 0);
@@ -1056,9 +1056,6 @@
 			continue;
 		if (iter->type == 3 && !(IS_CNA_CAPABLE(ha)))
 			continue;
-		if (iter->type == 0x27 &&
-		    (!IS_QLA27XX(ha) || !IS_QLA28XX(ha)))
-			continue;
 
 		sysfs_remove_bin_file(&host->shost_gendev.kobj,
 		    iter->attr);
@@ -1868,6 +1865,18 @@
 	return strlen(buf);
 }
 
+static const struct {
+	u16 rate;
+	char *str;
+} port_speed_str[] = {
+	{ PORT_SPEED_4GB, "4" },
+	{ PORT_SPEED_8GB, "8" },
+	{ PORT_SPEED_16GB, "16" },
+	{ PORT_SPEED_32GB, "32" },
+	{ PORT_SPEED_64GB, "64" },
+	{ PORT_SPEED_10GB, "10" },
+};
+
 static ssize_t
 qla2x00_port_speed_show(struct device *dev, struct device_attribute *attr,
     char *buf)
@@ -1875,7 +1884,8 @@
 	struct scsi_qla_host *vha = shost_priv(dev_to_shost(dev));
 	struct qla_hw_data *ha = vha->hw;
 	ssize_t rval;
-	char *spd[7] = {"0", "0", "0", "4", "8", "16", "32"};
+	u16 i;
+	char *speed = "Unknown";
 
 	rval = qla2x00_get_data_rate(vha);
 	if (rval != QLA_SUCCESS) {
@@ -1884,7 +1894,14 @@
 		return -EINVAL;
 	}
 
-	return scnprintf(buf, PAGE_SIZE, "%s\n", spd[ha->link_data_rate]);
+	for (i = 0; i < ARRAY_SIZE(port_speed_str); i++) {
+		if (port_speed_str[i].rate != ha->link_data_rate)
+			continue;
+		speed = port_speed_str[i].str;
+		break;
+	}
+
+	return scnprintf(buf, PAGE_SIZE, "%s\n", speed);
 }
 
 static ssize_t
@@ -2688,24 +2705,40 @@
 	if (!fcport)
 		return;
 
-	/* Now that the rport has been deleted, set the fcport state to
-	   FCS_DEVICE_DEAD */
-	qla2x00_set_fcport_state(fcport, FCS_DEVICE_DEAD);
+	ql_dbg(ql_dbg_async, fcport->vha, 0x5101,
+	       DBG_FCPORT_PRFMT(fcport, "dev_loss_tmo expiry, rport_state=%d",
+				rport->port_state));
+
+	/*
+	 * Now that the rport has been deleted, set the fcport state to
+	 * FCS_DEVICE_DEAD, if the fcport is still lost.
+	 */
+	if (fcport->scan_state != QLA_FCPORT_FOUND)
+		qla2x00_set_fcport_state(fcport, FCS_DEVICE_DEAD);
 
 	/*
 	 * Transport has effectively 'deleted' the rport, clear
 	 * all local references.
 	 */
 	spin_lock_irqsave(host->host_lock, flags);
-	fcport->rport = fcport->drport = NULL;
-	*((fc_port_t **)rport->dd_data) = NULL;
+	/* Confirm port has not reappeared before clearing pointers. */
+	if (rport->port_state != FC_PORTSTATE_ONLINE) {
+		fcport->rport = fcport->drport = NULL;
+		*((fc_port_t **)rport->dd_data) = NULL;
+	}
 	spin_unlock_irqrestore(host->host_lock, flags);
 
 	if (test_bit(ABORT_ISP_ACTIVE, &fcport->vha->dpc_flags))
 		return;
 
 	if (unlikely(pci_channel_offline(fcport->vha->hw->pdev))) {
-		qla2x00_abort_all_cmds(fcport->vha, DID_NO_CONNECT << 16);
+		/* Will wait for wind down of adapter */
+		ql_dbg(ql_dbg_aer, fcport->vha, 0x900c,
+		    "%s pci offline detected (id %06x)\n", __func__,
+		    fcport->d_id.b24);
+		qla_pci_set_eeh_busy(fcport->vha);
+		qla2x00_eh_wait_for_pending_commands(fcport->vha, fcport->d_id.b24,
+		    0, WAIT_TARGET);
 		return;
 	}
 }
@@ -2714,6 +2747,7 @@
 qla2x00_terminate_rport_io(struct fc_rport *rport)
 {
 	fc_port_t *fcport = *(fc_port_t **)rport->dd_data;
+	scsi_qla_host_t *vha;
 
 	if (!fcport)
 		return;
@@ -2723,25 +2757,49 @@
 
 	if (test_bit(ABORT_ISP_ACTIVE, &fcport->vha->dpc_flags))
 		return;
+	vha = fcport->vha;
 
 	if (unlikely(pci_channel_offline(fcport->vha->hw->pdev))) {
-		qla2x00_abort_all_cmds(fcport->vha, DID_NO_CONNECT << 16);
+		/* Will wait for wind down of adapter */
+		ql_dbg(ql_dbg_aer, fcport->vha, 0x900b,
+		    "%s pci offline detected (id %06x)\n", __func__,
+		    fcport->d_id.b24);
+		qla_pci_set_eeh_busy(vha);
+		qla2x00_eh_wait_for_pending_commands(fcport->vha, fcport->d_id.b24,
+			0, WAIT_TARGET);
 		return;
 	}
 	/*
 	 * At this point all fcport's software-states are cleared.  Perform any
 	 * final cleanup of firmware resources (PCBs and XCBs).
+	 *
+	 * Attempt to cleanup only lost devices.
 	 */
 	if (fcport->loop_id != FC_NO_LOOP_ID) {
-		if (IS_FWI2_CAPABLE(fcport->vha->hw)) {
+		if (IS_FWI2_CAPABLE(fcport->vha->hw) &&
+		    fcport->scan_state != QLA_FCPORT_FOUND) {
 			if (fcport->loop_id != FC_NO_LOOP_ID)
 				fcport->logout_on_delete = 1;
 
-			qlt_schedule_sess_for_deletion(fcport);
-		} else {
+			if (!EDIF_NEGOTIATION_PENDING(fcport)) {
+				ql_dbg(ql_dbg_disc, fcport->vha, 0x911e,
+				       "%s %d schedule session deletion\n", __func__,
+				       __LINE__);
+				qlt_schedule_sess_for_deletion(fcport);
+			}
+		} else if (!IS_FWI2_CAPABLE(fcport->vha->hw)) {
 			qla2x00_port_logout(fcport->vha, fcport);
 		}
 	}
+
+	/* check for any straggling io left behind */
+	if (qla2x00_eh_wait_for_pending_commands(fcport->vha, fcport->d_id.b24, 0, WAIT_TARGET)) {
+		ql_log(ql_log_warn, vha, 0x300b,
+		       "IO not return.  Resetting. \n");
+		set_bit(ISP_ABORT_NEEDED, &vha->dpc_flags);
+		qla2xxx_wake_dpc(vha);
+		qla2x00_wait_for_chip_reset(vha);
+	}
 }
 
 static int
@@ -3036,8 +3094,6 @@
 			vha->flags.difdix_supported = 1;
 			ql_dbg(ql_dbg_user, vha, 0x7082,
 			    "Registered for DIF/DIX type 1 and 3 protection.\n");
-			if (ql2xenabledif == 1)
-				prot = SHOST_DIX_TYPE0_PROTECTION;
 			scsi_host_set_prot(vha->host,
 			    prot | SHOST_DIF_TYPE1_PROTECTION
 			    | SHOST_DIF_TYPE2_PROTECTION
@@ -3247,6 +3303,7 @@
 	.show_host_node_name = 1,
 	.show_host_port_name = 1,
 	.show_host_supported_classes = 1,
+	.show_host_supported_speeds = 1,
 
 	.get_host_port_id = qla2x00_get_host_port_id,
 	.show_host_port_id = 1,
@@ -3286,11 +3343,34 @@
 	.bsg_timeout = qla24xx_bsg_timeout,
 };
 
+static uint
+qla2x00_get_host_supported_speeds(scsi_qla_host_t *vha, uint speeds)
+{
+	uint supported_speeds = FC_PORTSPEED_UNKNOWN;
+
+	if (speeds & FDMI_PORT_SPEED_64GB)
+		supported_speeds |= FC_PORTSPEED_64GBIT;
+	if (speeds & FDMI_PORT_SPEED_32GB)
+		supported_speeds |= FC_PORTSPEED_32GBIT;
+	if (speeds & FDMI_PORT_SPEED_16GB)
+		supported_speeds |= FC_PORTSPEED_16GBIT;
+	if (speeds & FDMI_PORT_SPEED_8GB)
+		supported_speeds |= FC_PORTSPEED_8GBIT;
+	if (speeds & FDMI_PORT_SPEED_4GB)
+		supported_speeds |= FC_PORTSPEED_4GBIT;
+	if (speeds & FDMI_PORT_SPEED_2GB)
+		supported_speeds |= FC_PORTSPEED_2GBIT;
+	if (speeds & FDMI_PORT_SPEED_1GB)
+		supported_speeds |= FC_PORTSPEED_1GBIT;
+
+	return supported_speeds;
+}
+
 void
 qla2x00_init_host_attr(scsi_qla_host_t *vha)
 {
 	struct qla_hw_data *ha = vha->hw;
-	u32 speeds = FC_PORTSPEED_UNKNOWN;
+	u32 speeds = 0, fdmi_speed = 0;
 
 	fc_host_dev_loss_tmo(vha->host) = ha->port_down_retry_count;
 	fc_host_node_name(vha->host) = wwn_to_u64(vha->node_name);
@@ -3300,7 +3380,8 @@
 	fc_host_max_npiv_vports(vha->host) = ha->max_npiv_vports;
 	fc_host_npiv_vports_inuse(vha->host) = ha->cur_vport_count;
 
-	speeds = qla25xx_fdmi_port_speed_capability(ha);
+	fdmi_speed = qla25xx_fdmi_port_speed_capability(ha);
+	speeds = qla2x00_get_host_supported_speeds(vha, fdmi_speed);
 
 	fc_host_supported_speeds(vha->host) = speeds;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_bsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_bsg.c
@@ -24,16 +24,21 @@
 {
 	struct bsg_job *bsg_job = sp->u.bsg_job;
 	struct fc_bsg_reply *bsg_reply = bsg_job->reply;
+	struct completion *comp = sp->comp;
 
 	ql_dbg(ql_dbg_user, sp->vha, 0x7009,
 	    "%s: sp hdl %x, result=%x bsg ptr %p\n",
 	    __func__, sp->handle, res, bsg_job);
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 
 	bsg_reply->result = res;
 	bsg_job_done(bsg_job, bsg_reply->result,
 		       bsg_reply->reply_payload_rcv_len);
+
+	if (comp)
+		complete(comp);
 }
 
 void qla2x00_bsg_sp_free(srb_t *sp)
@@ -277,11 +282,15 @@
 	const char *type;
 	int req_sg_cnt, rsp_sg_cnt;
 	int rval =  (DID_ERROR << 16);
-	uint16_t nextlid = 0;
 	uint32_t els_cmd = 0;
+	int qla_port_allocated = 0;
 
 	if (bsg_request->msgcode == FC_BSG_RPT_ELS) {
 		rport = fc_bsg_to_rport(bsg_job);
+		if (!rport) {
+			rval = -ENOMEM;
+			goto done;
+		}
 		fcport = *(fc_port_t **) rport->dd_data;
 		host = rport_to_shost(rport);
 		vha = shost_priv(host);
@@ -319,7 +328,7 @@
 		    "request_sg_cnt=%x reply_sg_cnt=%x.\n",
 		    bsg_job->request_payload.sg_cnt,
 		    bsg_job->reply_payload.sg_cnt);
-		rval = -EPERM;
+		rval = -ENOBUFS;
 		goto done;
 	}
 
@@ -328,9 +337,9 @@
 		/* make sure the rport is logged in,
 		 * if not perform fabric login
 		 */
-		if (qla2x00_fabric_login(vha, fcport, &nextlid)) {
+		if (atomic_read(&fcport->state) != FCS_ONLINE) {
 			ql_dbg(ql_dbg_user, vha, 0x7003,
-			    "Failed to login port %06X for ELS passthru.\n",
+			    "Port %06X is not online for ELS passthru.\n",
 			    fcport->d_id.b24);
 			rval = -EIO;
 			goto done;
@@ -347,6 +356,7 @@
 			goto done;
 		}
 
+		qla_port_allocated = 1;
 		/* Initialize all required  fields of fcport */
 		fcport->vha = vha;
 		fcport->d_id.b.al_pa =
@@ -431,7 +441,7 @@
 	goto done_free_fcport;
 
 done_free_fcport:
-	if (bsg_request->msgcode != FC_BSG_RPT_ELS)
+	if (qla_port_allocated)
 		qla2x00_free_fcport(fcport);
 done:
 	return rval;
@@ -484,16 +494,6 @@
 		goto done;
 	}
 
-	if ((req_sg_cnt !=  bsg_job->request_payload.sg_cnt) ||
-	    (rsp_sg_cnt != bsg_job->reply_payload.sg_cnt)) {
-		ql_log(ql_log_warn, vha, 0x7011,
-		    "request_sg_cnt: %x dma_request_sg_cnt: %x reply_sg_cnt:%x "
-		    "dma_reply_sg_cnt: %x\n", bsg_job->request_payload.sg_cnt,
-		    req_sg_cnt, bsg_job->reply_payload.sg_cnt, rsp_sg_cnt);
-		rval = -EAGAIN;
-		goto done_unmap_sg;
-	}
-
 	if (!vha->flags.online) {
 		ql_log(ql_log_warn, vha, 0x7012,
 		    "Host is not online.\n");
@@ -2897,6 +2897,8 @@
 
 	if (bsg_request->msgcode == FC_BSG_RPT_ELS) {
 		rport = fc_bsg_to_rport(bsg_job);
+		if (!rport)
+			return ret;
 		host = rport_to_shost(rport);
 		vha = shost_priv(host);
 	} else {
@@ -2958,58 +2960,151 @@
 	return ret;
 }
 
-int
-qla24xx_bsg_timeout(struct bsg_job *bsg_job)
+static bool qla_bsg_found(struct qla_qpair *qpair, struct bsg_job *bsg_job)
 {
+	bool found, do_bsg_done;
 	struct fc_bsg_reply *bsg_reply = bsg_job->reply;
 	scsi_qla_host_t *vha = shost_priv(fc_bsg_to_shost(bsg_job));
 	struct qla_hw_data *ha = vha->hw;
-	srb_t *sp;
-	int cnt, que;
+	srb_t *sp = NULL;
+	int cnt;
 	unsigned long flags;
 	struct req_que *req;
+	int rval;
+	DECLARE_COMPLETION_ONSTACK(comp);
+	uint32_t ratov_j;
 
-	ql_log(ql_log_info, vha, 0x708b, "%s CMD timeout. bsg ptr %p.\n",
-	    __func__, bsg_job);
-	/* find the bsg job from the active list of commands */
-	spin_lock_irqsave(&ha->hardware_lock, flags);
-	for (que = 0; que < ha->max_req_queues; que++) {
-		req = ha->req_q_map[que];
-		if (!req)
-			continue;
+	found = do_bsg_done = false;
 
-		for (cnt = 1; cnt < req->num_outstanding_cmds; cnt++) {
-			sp = req->outstanding_cmds[cnt];
-			if (sp &&
-			    (sp->type == SRB_CT_CMD ||
-			     sp->type == SRB_ELS_CMD_HST ||
-			     sp->type == SRB_ELS_CMD_HST_NOLOGIN ||
-			     sp->type == SRB_FXIOCB_BCMD) &&
-			    sp->u.bsg_job == bsg_job) {
-				req->outstanding_cmds[cnt] = NULL;
-				spin_unlock_irqrestore(&ha->hardware_lock, flags);
-				if (ha->isp_ops->abort_command(sp)) {
-					ql_log(ql_log_warn, vha, 0x7089,
-					    "mbx abort_command failed.\n");
-					bsg_reply->result = -EIO;
-				} else {
-					ql_dbg(ql_dbg_user, vha, 0x708a,
-					    "mbx abort_command success.\n");
-					bsg_reply->result = 0;
-				}
-				spin_lock_irqsave(&ha->hardware_lock, flags);
-				goto done;
+	spin_lock_irqsave(qpair->qp_lock_ptr, flags);
+	req = qpair->req;
 
-			}
+	for (cnt = 1; cnt < req->num_outstanding_cmds; cnt++) {
+		sp = req->outstanding_cmds[cnt];
+		if (sp &&
+		    (sp->type == SRB_CT_CMD ||
+		     sp->type == SRB_ELS_CMD_HST ||
+		     sp->type == SRB_ELS_CMD_HST_NOLOGIN) &&
+		    sp->u.bsg_job == bsg_job) {
+
+			found = true;
+			sp->comp = &comp;
+			break;
 		}
 	}
-	spin_unlock_irqrestore(&ha->hardware_lock, flags);
-	ql_log(ql_log_info, vha, 0x708b, "SRB not found to abort.\n");
+	spin_unlock_irqrestore(qpair->qp_lock_ptr, flags);
+
+	if (!found)
+		return false;
+
+	if (ha->flags.eeh_busy) {
+		/* skip over abort.  EEH handling will return the bsg. Wait for it */
+		rval = QLA_SUCCESS;
+		ql_dbg(ql_dbg_user, vha, 0x802c,
+			"eeh encounter. bsg %p sp=%p handle=%x \n",
+			bsg_job, sp, sp->handle);
+	} else {
+		rval = ha->isp_ops->abort_command(sp);
+		ql_dbg(ql_dbg_user, vha, 0x802c,
+			"Aborting bsg %p sp=%p handle=%x rval=%x\n",
+			bsg_job, sp, sp->handle, rval);
+	}
+
+	switch (rval) {
+	case QLA_SUCCESS:
+		/* Wait for the command completion. */
+		ratov_j = ha->r_a_tov / 10 * 4 * 1000;
+		ratov_j = msecs_to_jiffies(ratov_j);
+
+		if (!wait_for_completion_timeout(&comp, ratov_j)) {
+			ql_log(ql_log_info, vha, 0x7089,
+				"bsg abort timeout.  bsg=%p sp=%p handle %#x .\n",
+				bsg_job, sp, sp->handle);
+
+			do_bsg_done = true;
+		} else {
+			/* fw had returned the bsg */
+			ql_dbg(ql_dbg_user, vha, 0x708a,
+				"bsg abort success. bsg %p sp=%p handle=%#x\n",
+				bsg_job, sp, sp->handle);
+			do_bsg_done = false;
+		}
+		break;
+	default:
+		ql_log(ql_log_info, vha, 0x704f,
+			"bsg abort fail.  bsg=%p sp=%p rval=%x.\n",
+			bsg_job, sp, rval);
+
+		do_bsg_done = true;
+		break;
+	}
+
+	if (!do_bsg_done)
+		return true;
+
+	spin_lock_irqsave(qpair->qp_lock_ptr, flags);
+	/*
+	 * recheck to make sure it's still the same bsg_job due to
+	 * qp_lock_ptr was released earlier.
+	 */
+	if (req->outstanding_cmds[cnt] &&
+	    req->outstanding_cmds[cnt]->u.bsg_job != bsg_job) {
+		/* fw had returned the bsg */
+		spin_unlock_irqrestore(qpair->qp_lock_ptr, flags);
+		return true;
+	}
+	req->outstanding_cmds[cnt] = NULL;
+	spin_unlock_irqrestore(qpair->qp_lock_ptr, flags);
+
+	/* ref: INIT */
+	sp->comp = NULL;
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	bsg_reply->result = -ENXIO;
-	return 0;
+	bsg_reply->reply_payload_rcv_len = 0;
+
+	ql_dbg(ql_dbg_user, vha, 0x7051,
+	       "%s bsg_job_done : bsg %p result %#x sp %p.\n",
+	       __func__, bsg_job, bsg_reply->result, sp);
+
+	bsg_job_done(bsg_job, bsg_reply->result, bsg_reply->reply_payload_rcv_len);
+
+	return true;
+}
+
+int
+qla24xx_bsg_timeout(struct bsg_job *bsg_job)
+{
+	struct fc_bsg_request *bsg_request = bsg_job->request;
+	scsi_qla_host_t *vha = shost_priv(fc_bsg_to_shost(bsg_job));
+	struct qla_hw_data *ha = vha->hw;
+	int i;
+	struct qla_qpair *qpair;
+
+	ql_log(ql_log_info, vha, 0x708b,
+	       "%s CMD timeout. bsg ptr %p msgcode %x vendor cmd %x\n",
+	       __func__, bsg_job, bsg_request->msgcode,
+	       bsg_request->rqst_data.h_vendor.vendor_cmd[0]);
+
+	if (qla2x00_isp_reg_stat(ha)) {
+		ql_log(ql_log_info, vha, 0x9007,
+		    "PCI/Register disconnect.\n");
+		qla_pci_set_eeh_busy(vha);
+	}
+
+	if (qla_bsg_found(ha->base_qpair, bsg_job))
+		goto done;
+
+	/* find the bsg job from the active list of commands */
+	for (i = 0; i < ha->max_qpairs; i++) {
+		qpair = vha->hw->queue_pair_map[i];
+		if (!qpair)
+			continue;
+		if (qla_bsg_found(qpair, bsg_job))
+			goto done;
+	}
+
+	ql_log(ql_log_info, vha, 0x708b, "SRB not found to abort.\n");
 
 done:
-	spin_unlock_irqrestore(&ha->hardware_lock, flags);
-	sp->free(sp);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_dbg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_dbg.c
@@ -18,7 +18,7 @@
  * | Queue Command and IO tracing |       0x3074       | 0x300b         |
  * |                              |                    | 0x3027-0x3028  |
  * |                              |                    | 0x303d-0x3041  |
- * |                              |                    | 0x302d,0x3033  |
+ * |                              |                    | 0x302e,0x3033  |
  * |                              |                    | 0x3036,0x3038  |
  * |                              |                    | 0x303a		|
  * | DPC Thread                   |       0x4023       | 0x4002,0x4013  |
@@ -2491,6 +2491,9 @@
 	struct va_format vaf;
 	char pbuf[64];
 
+	if (!ql_mask_match(level) && !trace_ql_dbg_log_enabled())
+		return;
+
 	va_start(va, fmt);
 
 	vaf.fmt = fmt;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_def.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_def.h
@@ -78,7 +78,7 @@
 #include "qla_nvme.h"
 #define QLA2XXX_DRIVER_NAME	"qla2xxx"
 #define QLA2XXX_APIDEV		"ql2xapidev"
-#define QLA2XXX_MANUFACTURER	"QLogic Corporation"
+#define QLA2XXX_MANUFACTURER	"Marvell"
 
 /*
  * We have MAILBOX_REGISTER_COUNT sized arrays in a few places,
@@ -452,6 +452,16 @@
 	return res;
 }
 
+struct tmf_arg {
+	struct list_head tmf_elem;
+	struct qla_qpair *qpair;
+	struct fc_port *fcport;
+	struct scsi_qla_host *vha;
+	u64 lun;
+	u32 flags;
+	uint8_t modifier;
+};
+
 struct els_logo_payload {
 	uint8_t opcode;
 	uint8_t rsvd[3];
@@ -531,6 +541,10 @@
 			uint32_t data;
 			struct completion comp;
 			__le16 comp_status;
+
+			uint8_t modifier;
+			uint8_t vp_index;
+			uint16_t loop_id;
 		} tmf;
 		struct {
 #define SRB_FXDISC_REQ_DMA_VALID	BIT_0
@@ -634,6 +648,7 @@
 #define SRB_SA_UPDATE	25
 #define SRB_ELS_CMD_HST_NOLOGIN 26
 #define SRB_SA_REPLACE	27
+#define SRB_MARKER	28
 
 struct qla_els_pt_arg {
 	u8 els_opcode;
@@ -655,7 +670,7 @@
 
 struct iocb_resource {
 	u8 res_type;
-	u8 pad;
+	u8  exch_cnt;
 	u16 iocb_cnt;
 };
 
@@ -676,7 +691,6 @@
 	struct iocb_resource iores;
 	struct kref cmd_kref;	/* need to migrate ref_count over to this */
 	void *priv;
-	wait_queue_head_t nvme_ls_waitq;
 	struct fc_port *fcport;
 	struct scsi_qla_host *vha;
 	unsigned int start_timer:1;
@@ -726,6 +740,11 @@
 	 * code.
 	 */
 	void (*put_fn)(struct kref *kref);
+
+	/*
+	 * Report completion for asynchronous commands.
+	 */
+	void (*async_done)(struct srb *sp, int res);
 } srb_t;
 
 #define GET_CMD_SP(sp) (sp->u.scmd.cmd)
@@ -2153,6 +2172,11 @@
 #define CS_IOCB_ERROR		0x31	/* Generic error for IOCB request
 					   failure */
 #define CS_REJECT_RECEIVED	0x4E	/* Reject received */
+#define CS_EDIF_AUTH_ERROR	0x63	/* decrypt error */
+#define CS_EDIF_PAD_LEN_ERROR	0x65	/* pad > frame size, not 4byte align */
+#define CS_EDIF_INV_REQ		0x66	/* invalid request */
+#define CS_EDIF_SPI_ERROR	0x67	/* rx frame unable to locate sa */
+#define CS_EDIF_HDR_ERROR	0x69	/* data frame != expected len */
 #define CS_BAD_PAYLOAD		0x80	/* Driver defined */
 #define CS_UNKNOWN		0x81	/* Driver defined */
 #define CS_RETRY		0x82	/* Driver defined */
@@ -2520,7 +2544,6 @@
 	unsigned int do_prli_nvme:1;
 
 	uint8_t nvme_flag;
-
 	uint8_t node_name[WWN_SIZE];
 	uint8_t port_name[WWN_SIZE];
 	port_id_t d_id;
@@ -2886,7 +2909,11 @@
 #define FDMI_PORT_SPEED_8GB		0x10
 #define FDMI_PORT_SPEED_16GB		0x20
 #define FDMI_PORT_SPEED_32GB		0x40
-#define FDMI_PORT_SPEED_64GB		0x80
+#define FDMI_PORT_SPEED_20GB		0x80
+#define FDMI_PORT_SPEED_40GB		0x100
+#define FDMI_PORT_SPEED_128GB		0x200
+#define FDMI_PORT_SPEED_64GB		0x400
+#define FDMI_PORT_SPEED_256GB		0x800
 #define FDMI_PORT_SPEED_UNKNOWN		0x8000
 
 #define FC_CLASS_2	0x04
@@ -3192,6 +3219,8 @@
 #define GFF_NVME_OFFSET		23 /* type = 28h */
 		struct {
 			uint8_t fc4_features[128];
+#define FC4_FF_TARGET    BIT_0
+#define FC4_FF_INITIATOR BIT_1
 		} gff_id;
 		struct {
 			uint8_t reserved;
@@ -3235,6 +3264,8 @@
 struct fab_scan {
 	struct fab_scan_rp *l;
 	u32 size;
+	u32 rscn_gen_start;
+	u32 rscn_gen_end;
 	u16 scan_retry;
 #define MAX_SCAN_RETRIES 5
 	enum scan_flags_t scan_flags;
@@ -3432,6 +3463,7 @@
 	int have_irq;
 	int in_use;
 	uint32_t vector;
+	uint32_t vector_base0;
 	uint16_t entry;
 	char name[30];
 	void *handle;
@@ -3691,6 +3723,20 @@
 	u16 iocbs_limit;
 	u16 iocbs_qp_limit;
 	u16 iocbs_used;
+	u16 exch_total;
+	u16 exch_limit;
+	u16 exch_used;
+	u16 pad;
+};
+
+struct qla_fw_res {
+	u16      iocb_total;
+	u16      iocb_limit;
+	atomic_t iocb_used;
+
+	u16      exch_total;
+	u16      exch_limit;
+	atomic_t exch_used;
 };
 
 #define QLA_IOCB_PCT_LIMIT 95
@@ -3747,9 +3793,11 @@
 	uint64_t retry_term_jiff;
 	struct qla_tgt_counters tgt_counters;
 	uint16_t cpuid;
+	bool cpu_mapped;
 	struct qla_fw_resources fwres ____cacheline_aligned;
 	u32	cmd_cnt;
 	u32	cmd_completion_cnt;
+	u32	prev_completion_cnt;
 };
 
 /* Place holder for FW buffer parameters */
@@ -3962,6 +4010,7 @@
 	/* SRB cache. */
 #define SRB_MIN_REQ     128
 	mempool_t       *srb_mempool;
+	u8 port_name[WWN_SIZE];
 
 	volatile struct {
 		uint32_t	mbox_int		:1;
@@ -3980,6 +4029,8 @@
 		uint32_t	npiv_supported		:1;
 		uint32_t	pci_channel_io_perm_failure	:1;
 		uint32_t	fce_enabled		:1;
+		uint32_t	user_enabled_fce	:1;
+		uint32_t	fce_dump_buf_alloced	:1;
 		uint32_t	fac_supported		:1;
 
 		uint32_t	chip_reset_done		:1;
@@ -4027,6 +4078,9 @@
 		uint32_t	n2n_fw_acc_sec:1;
 		uint32_t	plogi_template_valid:1;
 		uint32_t	port_isolated:1;
+		uint32_t	eeh_flush:2;
+#define EEH_FLUSH_RDY  1
+#define EEH_FLUSH_DONE 2
 	} flags;
 
 	uint16_t max_exchg;
@@ -4061,6 +4115,7 @@
 	uint32_t		rsp_que_len;
 	uint32_t		req_que_off;
 	uint32_t		rsp_que_off;
+	unsigned long		eeh_jif;
 
 	/* Multi queue data structs */
 	device_reg_t *mqiobase;
@@ -4070,6 +4125,7 @@
 	struct req_que **req_q_map;
 	struct rsp_que **rsp_q_map;
 	struct qla_qpair **queue_pair_map;
+	struct qla_qpair **qp_cpu_map;
 	unsigned long req_qid_map[(QLA_MAX_QUEUES / 8) / sizeof(unsigned long)];
 	unsigned long rsp_qid_map[(QLA_MAX_QUEUES / 8) / sizeof(unsigned long)];
 	unsigned long qpair_qid_map[(QLA_MAX_QUEUES / 8)
@@ -4243,8 +4299,8 @@
 #define IS_OEM_001(ha)          ((ha)->device_type & DT_OEM_001)
 #define HAS_EXTENDED_IDS(ha)    ((ha)->device_type & DT_EXTENDED_IDS)
 #define IS_CT6_SUPPORTED(ha)	((ha)->device_type & DT_CT6_SUPPORTED)
-#define IS_MQUE_CAPABLE(ha)	((ha)->mqenable || IS_QLA83XX(ha) || \
-				IS_QLA27XX(ha) || IS_QLA28XX(ha))
+#define IS_MQUE_CAPABLE(ha)	(IS_QLA83XX(ha) || IS_QLA27XX(ha) || \
+				 IS_QLA28XX(ha))
 #define IS_BIDI_CAPABLE(ha) \
     (IS_QLA25XX(ha) || IS_QLA2031(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha))
 /* Bit 21 of fw_attributes decides the MCTP capabilities */
@@ -4261,8 +4317,10 @@
 #define QLA_ABTS_WAIT_ENABLED(_sp) \
 	(QLA_NVME_IOS(_sp) && QLA_ABTS_FW_ENABLED(_sp->fcport->vha->hw))
 
-#define IS_PI_UNINIT_CAPABLE(ha)	(IS_QLA83XX(ha) || IS_QLA27XX(ha))
-#define IS_PI_IPGUARD_CAPABLE(ha)	(IS_QLA83XX(ha) || IS_QLA27XX(ha))
+#define IS_PI_UNINIT_CAPABLE(ha)	(IS_QLA83XX(ha) || IS_QLA27XX(ha) || \
+					 IS_QLA28XX(ha))
+#define IS_PI_IPGUARD_CAPABLE(ha)	(IS_QLA83XX(ha) || IS_QLA27XX(ha) || \
+					 IS_QLA28XX(ha))
 #define IS_PI_DIFB_DIX0_CAPABLE(ha)	(0)
 #define IS_PI_SPLIT_DET_CAPABLE_HBA(ha)	(IS_QLA83XX(ha) || IS_QLA27XX(ha) || \
 					IS_QLA28XX(ha))
@@ -4312,7 +4370,6 @@
 	uint8_t		aen_mbx_count;
 	atomic_t	num_pend_mbx_stage1;
 	atomic_t	num_pend_mbx_stage2;
-	atomic_t	num_pend_mbx_stage3;
 	uint16_t	frame_payload_size;
 
 	uint32_t	login_retry_count;
@@ -4582,6 +4639,8 @@
 		uint32_t	flt_region_aux_img_status_sec;
 	};
 	uint8_t         active_image;
+	uint8_t active_tmf;
+#define MAX_ACTIVE_TMF 8
 
 	/* Needed for BEACON */
 	uint16_t        beacon_blink_led;
@@ -4596,6 +4655,8 @@
 
 	struct qla_msix_entry *msix_entries;
 
+	struct list_head tmf_pending;
+	struct list_head tmf_active;
 	struct list_head        vp_list;        /* list of VP */
 	unsigned long   vp_idx_map[(MAX_MULTI_ID_FABRIC / 8) /
 			sizeof(unsigned long)];
@@ -4607,7 +4668,9 @@
 	struct qla_chip_state_84xx *cs84xx;
 	struct isp_operations *isp_ops;
 	struct workqueue_struct *wq;
+	struct work_struct heartbeat_work;
 	struct qlfc_fw fw_buf;
+	unsigned long last_heartbeat_run_jiffies;
 
 	/* FCP_CMND priority support */
 	struct qla_fcp_prio_cfg *fcp_prio_cfg;
@@ -4708,7 +4771,6 @@
 
 	struct qla_hw_data_stat stat;
 	pci_error_state_t pci_error_state;
-	u64 prev_cmd_cnt;
 	struct dma_pool *purex_dma_pool;
 	struct btree_head32 host_map;
 
@@ -4723,6 +4785,7 @@
 	spinlock_t sadb_lock;	/* protects list */
 	struct els_reject elsrej;
 	u8 edif_post_stop_cnt_down;
+	struct qla_fw_res fwres ____cacheline_aligned;
 };
 
 #define RX_ELS_SIZE (roundup(sizeof(struct enode) + ELS_MAX_PAYLOAD, SMP_CACHE_BYTES))
@@ -4854,7 +4917,6 @@
 #define SET_ZIO_THRESHOLD_NEEDED 32
 #define ISP_ABORT_TO_ROM	33
 #define VPORT_DELETE		34
-#define HEARTBEAT_CHK		38
 
 #define PROCESS_PUREX_IOCB	63
 
@@ -4913,6 +4975,7 @@
 
 	/* Counter to detect races between ELS and RSCN events */
 	atomic_t		generation_tick;
+	atomic_t		rscn_gen;
 	/* Time when global fcport update has been scheduled */
 	int			total_fcport_update_gen;
 	/* List of pending LOGOs, protected by tgt_mutex */
@@ -5093,17 +5156,17 @@
 		(test_bit(ISP_ABORT_NEEDED, &ha->dpc_flags) || \
 			 test_bit(LOOP_RESYNC_NEEDED, &ha->dpc_flags))
 
-#define QLA_VHA_MARK_BUSY(__vha, __bail) do {		\
-	atomic_inc(&__vha->vref_count);			\
-	mb();						\
-	if (__vha->flags.delete_progress) {		\
-		atomic_dec(&__vha->vref_count);		\
-		wake_up(&__vha->vref_waitq);		\
-		__bail = 1;				\
-	} else {					\
-		__bail = 0;				\
-	}						\
-} while (0)
+static inline bool qla_vha_mark_busy(scsi_qla_host_t *vha)
+{
+	atomic_inc(&vha->vref_count);
+	mb();
+	if (vha->flags.delete_progress) {
+		atomic_dec(&vha->vref_count);
+		wake_up(&vha->vref_waitq);
+		return true;
+	}
+	return false;
+}
 
 #define QLA_VHA_MARK_NOT_BUSY(__vha) do {		\
 	atomic_dec(&__vha->vref_count);			\
@@ -5427,4 +5490,18 @@
 #include "qla_gbl.h"
 #include "qla_dbg.h"
 #include "qla_inline.h"
+
+#define IS_SESSION_DELETED(_fcport) (_fcport->disc_state == DSC_DELETE_PEND || \
+				      _fcport->disc_state == DSC_DELETED)
+
+#define DBG_FCPORT_PRFMT(_fp, _fmt, _args...) \
+	"%s: %8phC: " _fmt " (state=%d disc_state=%d scan_state=%d loopid=0x%x deleted=%d flags=0x%x)\n", \
+	__func__, _fp->port_name, ##_args, atomic_read(&_fp->state), \
+	_fp->disc_state, _fp->scan_state, _fp->loop_id, _fp->deleted, \
+	_fp->flags
+
+#define TMF_NOT_READY(_fcport) \
+	(!_fcport || IS_SESSION_DELETED(_fcport) || atomic_read(&_fcport->state) != FCS_ONLINE || \
+	!_fcport->vha->hw->flags.fw_started)
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_dfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_dfs.c
@@ -116,7 +116,7 @@
 
 	sprintf(wwn, "pn-%016llx", wwn_to_u64(fp->port_name));
 	fp->dfs_rport_dir = debugfs_create_dir(wwn, vha->dfs_rport_root);
-	if (!fp->dfs_rport_dir)
+	if (IS_ERR(fp->dfs_rport_dir))
 		return;
 	if (NVME_TARGET(vha->hw, fp))
 		debugfs_create_file("dev_loss_tmo", 0600, fp->dfs_rport_dir,
@@ -235,7 +235,7 @@
 	uint16_t mb[MAX_IOCB_MB_REG];
 	int rc;
 	struct qla_hw_data *ha = vha->hw;
-	u16 iocbs_used, i;
+	u16 iocbs_used, i, exch_used;
 
 	rc = qla24xx_res_count_wait(vha, mb, SIZEOF_IOCB_MB_REG);
 	if (rc != QLA_SUCCESS) {
@@ -263,13 +263,29 @@
 	if (ql2xenforce_iocb_limit) {
 		/* lock is not require. It's an estimate. */
 		iocbs_used = ha->base_qpair->fwres.iocbs_used;
+		exch_used = ha->base_qpair->fwres.exch_used;
 		for (i = 0; i < ha->max_qpairs; i++) {
-			if (ha->queue_pair_map[i])
+			if (ha->queue_pair_map[i]) {
 				iocbs_used += ha->queue_pair_map[i]->fwres.iocbs_used;
+				exch_used += ha->queue_pair_map[i]->fwres.exch_used;
+			}
 		}
 
 		seq_printf(s, "Driver: estimate iocb used [%d] high water limit [%d]\n",
 			   iocbs_used, ha->base_qpair->fwres.iocbs_limit);
+
+		seq_printf(s, "estimate exchange used[%d] high water limit [%d]\n",
+			   exch_used, ha->base_qpair->fwres.exch_limit);
+
+		if (ql2xenforce_iocb_limit == 2) {
+			iocbs_used = atomic_read(&ha->fwres.iocb_used);
+			exch_used  = atomic_read(&ha->fwres.exch_used);
+			seq_printf(s, "        estimate iocb2 used [%d] high water limit [%d]\n",
+					iocbs_used, ha->fwres.iocb_limit);
+
+			seq_printf(s, "        estimate exchange2 used[%d] high water limit [%d] \n",
+					exch_used, ha->fwres.exch_limit);
+		}
 	}
 
 	return 0;
@@ -393,26 +409,31 @@
 
 	mutex_lock(&ha->fce_mutex);
 
-	seq_puts(s, "FCE Trace Buffer\n");
-	seq_printf(s, "In Pointer = %llx\n\n", (unsigned long long)ha->fce_wr);
-	seq_printf(s, "Base = %llx\n\n", (unsigned long long) ha->fce_dma);
-	seq_puts(s, "FCE Enable Registers\n");
-	seq_printf(s, "%08x %08x %08x %08x %08x %08x\n",
-	    ha->fce_mb[0], ha->fce_mb[2], ha->fce_mb[3], ha->fce_mb[4],
-	    ha->fce_mb[5], ha->fce_mb[6]);
-
-	fce = (uint32_t *) ha->fce;
-	fce_start = (unsigned long long) ha->fce_dma;
-	for (cnt = 0; cnt < fce_calc_size(ha->fce_bufs) / 4; cnt++) {
-		if (cnt % 8 == 0)
-			seq_printf(s, "\n%llx: ",
-			    (unsigned long long)((cnt * 4) + fce_start));
-		else
-			seq_putc(s, ' ');
-		seq_printf(s, "%08x", *fce++);
-	}
+	if (ha->flags.user_enabled_fce) {
+		seq_puts(s, "FCE Trace Buffer\n");
+		seq_printf(s, "In Pointer = %llx\n\n", (unsigned long long)ha->fce_wr);
+		seq_printf(s, "Base = %llx\n\n", (unsigned long long)ha->fce_dma);
+		seq_puts(s, "FCE Enable Registers\n");
+		seq_printf(s, "%08x %08x %08x %08x %08x %08x\n",
+			   ha->fce_mb[0], ha->fce_mb[2], ha->fce_mb[3], ha->fce_mb[4],
+			   ha->fce_mb[5], ha->fce_mb[6]);
+
+		fce = (uint32_t *)ha->fce;
+		fce_start = (unsigned long long)ha->fce_dma;
+		for (cnt = 0; cnt < fce_calc_size(ha->fce_bufs) / 4; cnt++) {
+			if (cnt % 8 == 0)
+				seq_printf(s, "\n%llx: ",
+					   (unsigned long long)((cnt * 4) + fce_start));
+			else
+				seq_putc(s, ' ');
+			seq_printf(s, "%08x", *fce++);
+		}
 
-	seq_puts(s, "\nEnd\n");
+		seq_puts(s, "\nEnd\n");
+	} else {
+		seq_puts(s, "FCE Trace is currently not enabled\n");
+		seq_puts(s, "\techo [ 1 | 0 ] > fce\n");
+	}
 
 	mutex_unlock(&ha->fce_mutex);
 
@@ -451,7 +472,7 @@
 	struct qla_hw_data *ha = vha->hw;
 	int rval;
 
-	if (ha->flags.fce_enabled)
+	if (ha->flags.fce_enabled || !ha->fce)
 		goto out;
 
 	mutex_lock(&ha->fce_mutex);
@@ -472,11 +493,88 @@
 	return single_release(inode, file);
 }
 
+static ssize_t
+qla2x00_dfs_fce_write(struct file *file, const char __user *buffer,
+		      size_t count, loff_t *pos)
+{
+	struct seq_file *s = file->private_data;
+	struct scsi_qla_host *vha = s->private;
+	struct qla_hw_data *ha = vha->hw;
+	char *buf;
+	int rc = 0;
+	unsigned long enable;
+
+	if (!IS_QLA25XX(ha) && !IS_QLA81XX(ha) && !IS_QLA83XX(ha) &&
+	    !IS_QLA27XX(ha) && !IS_QLA28XX(ha)) {
+		ql_dbg(ql_dbg_user, vha, 0xd034,
+		       "this adapter does not support FCE.");
+		return -EINVAL;
+	}
+
+	buf = memdup_user_nul(buffer, count);
+	if (IS_ERR(buf)) {
+		ql_dbg(ql_dbg_user, vha, 0xd037,
+		    "fail to copy user buffer.");
+		return PTR_ERR(buf);
+	}
+
+	enable = kstrtoul(buf, 0, 0);
+	rc = count;
+
+	mutex_lock(&ha->fce_mutex);
+
+	if (enable) {
+		if (ha->flags.user_enabled_fce) {
+			mutex_unlock(&ha->fce_mutex);
+			goto out_free;
+		}
+		ha->flags.user_enabled_fce = 1;
+		if (!ha->fce) {
+			rc = qla2x00_alloc_fce_trace(vha);
+			if (rc) {
+				ha->flags.user_enabled_fce = 0;
+				mutex_unlock(&ha->fce_mutex);
+				goto out_free;
+			}
+
+			/* adjust fw dump buffer to take into account of this feature */
+			if (!ha->flags.fce_dump_buf_alloced)
+				qla2x00_alloc_fw_dump(vha);
+		}
+
+		if (!ha->flags.fce_enabled)
+			qla_enable_fce_trace(vha);
+
+		ql_dbg(ql_dbg_user, vha, 0xd045, "User enabled FCE .\n");
+	} else {
+		if (!ha->flags.user_enabled_fce) {
+			mutex_unlock(&ha->fce_mutex);
+			goto out_free;
+		}
+		ha->flags.user_enabled_fce = 0;
+		if (ha->flags.fce_enabled) {
+			qla2x00_disable_fce_trace(vha, NULL, NULL);
+			ha->flags.fce_enabled = 0;
+		}
+
+		qla2x00_free_fce_trace(ha);
+		/* no need to re-adjust fw dump buffer */
+
+		ql_dbg(ql_dbg_user, vha, 0xd04f, "User disabled FCE .\n");
+	}
+
+	mutex_unlock(&ha->fce_mutex);
+out_free:
+	kfree(buf);
+	return rc;
+}
+
 static const struct file_operations dfs_fce_ops = {
 	.open		= qla2x00_dfs_fce_open,
 	.read		= seq_read,
 	.llseek		= seq_lseek,
 	.release	= qla2x00_dfs_fce_release,
+	.write		= qla2x00_dfs_fce_write,
 };
 
 static int
@@ -562,8 +660,6 @@
 	if (!IS_QLA25XX(ha) && !IS_QLA81XX(ha) && !IS_QLA83XX(ha) &&
 	    !IS_QLA27XX(ha) && !IS_QLA28XX(ha))
 		goto out;
-	if (!ha->fce)
-		goto out;
 
 	if (qla2x00_dfs_root)
 		goto create_dir;
@@ -599,14 +695,14 @@
 	if (IS_QLA27XX(ha) || IS_QLA83XX(ha) || IS_QLA28XX(ha)) {
 		ha->tgt.dfs_naqp = debugfs_create_file("naqp",
 		    0400, ha->dfs_dir, vha, &dfs_naqp_ops);
-		if (!ha->tgt.dfs_naqp) {
+		if (IS_ERR(ha->tgt.dfs_naqp)) {
 			ql_log(ql_log_warn, vha, 0xd011,
 			       "Unable to create debugFS naqp node.\n");
 			goto out;
 		}
 	}
 	vha->dfs_rport_root = debugfs_create_dir("rports", ha->dfs_dir);
-	if (!vha->dfs_rport_root) {
+	if (IS_ERR(vha->dfs_rport_root)) {
 		ql_log(ql_log_warn, vha, 0xd012,
 		       "Unable to create debugFS rports node.\n");
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_edif.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_edif.c
@@ -218,7 +218,7 @@
 		    "%s edif not enabled\n", __func__);
 		goto done;
 	}
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		ql_dbg(ql_dbg_edif, vha, 0x09102,
 		    "%s doorbell not enabled\n", __func__);
 		goto done;
@@ -290,63 +290,6 @@
 	return false;
 }
 
-static void qla_edif_reset_auth_wait(struct fc_port *fcport, int state,
-		int waitonly)
-{
-	int cnt, max_cnt = 200;
-	bool traced = false;
-
-	fcport->keep_nport_handle = 1;
-
-	if (!waitonly) {
-		qla2x00_set_fcport_disc_state(fcport, state);
-		qlt_schedule_sess_for_deletion(fcport);
-	} else {
-		qla2x00_set_fcport_disc_state(fcport, state);
-	}
-
-	ql_dbg(ql_dbg_edif, fcport->vha, 0xf086,
-		"%s: waiting for session, max_cnt=%u\n",
-		__func__, max_cnt);
-
-	cnt = 0;
-
-	if (waitonly) {
-		/* Marker wait min 10 msecs. */
-		msleep(50);
-		cnt += 50;
-	}
-	while (1) {
-		if (!traced) {
-			ql_dbg(ql_dbg_edif, fcport->vha, 0xf086,
-			    "%s: session sleep.\n",
-			    __func__);
-			traced = true;
-		}
-		msleep(20);
-		cnt++;
-		if (waitonly && (fcport->disc_state == state ||
-			fcport->disc_state == DSC_LOGIN_COMPLETE))
-			break;
-		if (fcport->disc_state == DSC_LOGIN_AUTH_PEND)
-			break;
-		if (cnt > max_cnt)
-			break;
-	}
-
-	if (!waitonly) {
-		ql_dbg(ql_dbg_edif, fcport->vha, 0xf086,
-		    "%s: waited for session - %8phC, loopid=%x portid=%06x fcport=%p state=%u, cnt=%u\n",
-		    __func__, fcport->port_name, fcport->loop_id,
-		    fcport->d_id.b24, fcport, fcport->disc_state, cnt);
-	} else {
-		ql_dbg(ql_dbg_edif, fcport->vha, 0xf086,
-		    "%s: waited ONLY for session - %8phC, loopid=%x portid=%06x fcport=%p state=%u, cnt=%u\n",
-		    __func__, fcport->port_name, fcport->loop_id,
-		    fcport->d_id.b24, fcport, fcport->disc_state, cnt);
-	}
-}
-
 static void
 qla_edif_free_sa_ctl(fc_port_t *fcport, struct edif_sa_ctl *sa_ctl,
 	int index)
@@ -529,7 +472,8 @@
 	struct app_start_reply	appreply;
 	struct fc_port  *fcport, *tf;
 
-	ql_dbg(ql_dbg_edif, vha, 0x911d, "%s app start\n", __func__);
+	ql_log(ql_log_info, vha, 0x1313,
+	       "EDIF application registration with driver, FC device connections will be re-established.\n");
 
 	sg_copy_to_buffer(bsg_job->request_payload.sg_list,
 	    bsg_job->request_payload.sg_cnt, &appstart,
@@ -538,15 +482,17 @@
 	ql_dbg(ql_dbg_edif, vha, 0x911d, "%s app_vid=%x app_start_flags %x\n",
 	     __func__, appstart.app_info.app_vid, appstart.app_start_flags);
 
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		/* mark doorbell as active since an app is now present */
-		vha->e_dbell.db_flags = EDB_ACTIVE;
+		vha->e_dbell.db_flags |= EDB_ACTIVE;
 	} else {
-		ql_dbg(ql_dbg_edif, vha, 0x911e, "%s doorbell already active\n",
-		     __func__);
+		goto out;
 	}
 
 	if (N2N_TOPO(vha->hw)) {
+		list_for_each_entry_safe(fcport, tf, &vha->vp_fcports, list)
+			fcport->n2n_link_reset_cnt = 0;
+
 		if (vha->hw->flags.n2n_fw_acc_sec)
 			set_bit(N2N_LINK_RESET, &vha->dpc_flags);
 		else
@@ -554,39 +500,51 @@
 		qla2xxx_wake_dpc(vha);
 	} else {
 		list_for_each_entry_safe(fcport, tf, &vha->vp_fcports, list) {
+			ql_dbg(ql_dbg_edif, vha, 0x2058,
+			       "FCSP - nn %8phN pn %8phN portid=%06x.\n",
+			       fcport->node_name, fcport->port_name,
+			       fcport->d_id.b24);
 			ql_dbg(ql_dbg_edif, vha, 0xf084,
-			       "%s: sess %p %8phC lid %#04x s_id %06x logout %d\n",
-			       __func__, fcport, fcport->port_name,
-			       fcport->loop_id, fcport->d_id.b24,
-			       fcport->logout_on_delete);
-
-			ql_dbg(ql_dbg_edif, vha, 0xf084,
-			       "keep %d els_logo %d disc state %d auth state %d stop state %d\n",
-			       fcport->keep_nport_handle,
-			       fcport->send_els_logo, fcport->disc_state,
-			       fcport->edif.auth_state, fcport->edif.app_stop);
+			       "%s: se_sess %p / sess %p from port %8phC "
+			       "loop_id %#04x s_id %06x logout %d "
+			       "keep %d els_logo %d disc state %d auth state %d"
+			       "stop state %d\n",
+			       __func__, fcport->se_sess, fcport,
+			       fcport->port_name, fcport->loop_id,
+			       fcport->d_id.b24, fcport->logout_on_delete,
+			       fcport->keep_nport_handle, fcport->send_els_logo,
+			       fcport->disc_state, fcport->edif.auth_state,
+			       fcport->edif.app_stop);
 
 			if (atomic_read(&vha->loop_state) == LOOP_DOWN)
 				break;
-			if (!(fcport->flags & FCF_FCSP_DEVICE))
-				continue;
 
+			fcport->login_retry = vha->hw->login_retry_count;
+
+			fcport->edif.app_stop = 0;
+			fcport->edif.app_sess_online = 0;
 			fcport->edif.app_started = 1;
-			if (fcport->edif.app_stop ||
-			    (fcport->disc_state != DSC_LOGIN_COMPLETE &&
-			     fcport->disc_state != DSC_LOGIN_PEND &&
-			     fcport->disc_state != DSC_DELETED)) {
-				/* no activity */
-				fcport->edif.app_stop = 0;
-
-				ql_dbg(ql_dbg_edif, vha, 0x911e,
-				       "%s wwpn %8phC calling qla_edif_reset_auth_wait\n",
-				       __func__, fcport->port_name);
-				fcport->edif.app_sess_online = 1;
-				qla_edif_reset_auth_wait(fcport, DSC_LOGIN_PEND, 0);
-			}
+
+			if (fcport->scan_state != QLA_FCPORT_FOUND)
+				continue;
+
+			if (fcport->port_type == FCT_UNKNOWN &&
+			    !fcport->fc4_features)
+				rval = qla24xx_async_gffid(vha, fcport, true);
+
+			if (!rval && !(fcport->fc4_features & FC4_FF_TARGET ||
+			    fcport->port_type & (FCT_TARGET|FCT_NVME_TARGET)))
+				continue;
+
+			rval = 0;
+
+			ql_dbg(ql_dbg_edif, vha, 0x911e,
+			       "%s wwpn %8phC calling qla_edif_reset_auth_wait\n",
+			       __func__, fcport->port_name);
+			qlt_schedule_sess_for_deletion(fcport);
 			qla_edif_sa_ctl_init(vha, fcport);
 		}
+		set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
 	}
 
 	if (vha->pur_cinfo.enode_flags != ENODE_ACTIVE) {
@@ -597,18 +555,19 @@
 		     __func__);
 	}
 
+out:
 	appreply.host_support_edif = vha->hw->flags.edif_enabled;
 	appreply.edif_enode_active = vha->pur_cinfo.enode_flags;
 	appreply.edif_edb_active = vha->e_dbell.db_flags;
 
-	bsg_job->reply_len = sizeof(struct fc_bsg_reply) +
-	    sizeof(struct app_start_reply);
+	bsg_job->reply_len = sizeof(struct fc_bsg_reply);
 
 	SET_DID_STATUS(bsg_reply->result, DID_OK);
 
-	sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
-	    bsg_job->reply_payload.sg_cnt, &appreply,
-	    sizeof(struct app_start_reply));
+	bsg_reply->reply_payload_rcv_len = sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
+							       bsg_job->reply_payload.sg_cnt,
+							       &appreply,
+							       sizeof(struct app_start_reply));
 
 	ql_dbg(ql_dbg_edif, vha, 0x911d,
 	    "%s app start completed with 0x%x\n",
@@ -725,6 +684,11 @@
 	    bsg_job->request_payload.sg_cnt, &appplogiok,
 	    sizeof(struct auth_complete_cmd));
 
+	/* silent unaligned access warning */
+	portid.b.domain = appplogiok.u.d_id.b.domain;
+	portid.b.area   = appplogiok.u.d_id.b.area;
+	portid.b.al_pa  = appplogiok.u.d_id.b.al_pa;
+
 	switch (appplogiok.type) {
 	case PL_TYPE_WWPN:
 		fcport = qla2x00_find_fcport_by_wwpn(vha,
@@ -735,7 +699,7 @@
 			    __func__, appplogiok.u.wwpn);
 		break;
 	case PL_TYPE_DID:
-		fcport = qla2x00_find_fcport_by_pid(vha, &appplogiok.u.d_id);
+		fcport = qla2x00_find_fcport_by_pid(vha, &portid);
 		if (!fcport)
 			ql_dbg(ql_dbg_edif, vha, 0x911d,
 			    "%s d_id lookup failed: %x\n", __func__,
@@ -800,15 +764,15 @@
 		ql_dbg(ql_dbg_edif, vha, 0x911e,
 		    "%s AUTH complete - RESUME with prli for wwpn %8phC\n",
 		    __func__, fcport->port_name);
-		qla_edif_reset_auth_wait(fcport, DSC_LOGIN_PEND, 1);
 		qla24xx_post_prli_work(vha, fcport);
 	}
 
 errstate_exit:
 	bsg_job->reply_len = sizeof(struct fc_bsg_reply);
-	sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
-	    bsg_job->reply_payload.sg_cnt, &appplogireply,
-	    sizeof(struct app_plogi_reply));
+	bsg_reply->reply_payload_rcv_len = sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
+							       bsg_job->reply_payload.sg_cnt,
+							       &appplogireply,
+							       sizeof(struct app_plogi_reply));
 
 	return rval;
 }
@@ -834,6 +798,11 @@
 	    bsg_job->request_payload.sg_cnt, &appplogifail,
 	    sizeof(struct auth_complete_cmd));
 
+	/* silent unaligned access warning */
+	portid.b.domain = appplogifail.u.d_id.b.domain;
+	portid.b.area   = appplogifail.u.d_id.b.area;
+	portid.b.al_pa  = appplogifail.u.d_id.b.al_pa;
+
 	/*
 	 * TODO: edif: app has failed this plogi. Inform driver to
 	 * take any action (if any).
@@ -845,7 +814,7 @@
 		SET_DID_STATUS(bsg_reply->result, DID_OK);
 		break;
 	case PL_TYPE_DID:
-		fcport = qla2x00_find_fcport_by_pid(vha, &appplogifail.u.d_id);
+		fcport = qla2x00_find_fcport_by_pid(vha, &portid);
 		if (!fcport)
 			ql_dbg(ql_dbg_edif, vha, 0x911d,
 			    "%s d_id lookup failed: %x\n", __func__,
@@ -873,7 +842,7 @@
 
 		if (qla_ini_mode_enabled(fcport->vha)) {
 			fcport->send_els_logo = 1;
-			qla_edif_reset_auth_wait(fcport, DSC_LOGIN_PEND, 0);
+			qlt_schedule_sess_for_deletion(fcport);
 		}
 	}
 
@@ -891,7 +860,7 @@
 qla_edif_app_getfcinfo(scsi_qla_host_t *vha, struct bsg_job *bsg_job)
 {
 	int32_t			rval = 0;
-	int32_t			num_cnt;
+	int32_t			pcnt = 0;
 	struct fc_bsg_reply	*bsg_reply = bsg_job->reply;
 	struct app_pinfo_req	app_req;
 	struct app_pinfo_reply	*app_reply;
@@ -903,16 +872,14 @@
 	    bsg_job->request_payload.sg_cnt, &app_req,
 	    sizeof(struct app_pinfo_req));
 
-	num_cnt = app_req.num_ports;	/* num of ports alloc'd by app */
-
 	app_reply = kzalloc((sizeof(struct app_pinfo_reply) +
-	    sizeof(struct app_pinfo) * num_cnt), GFP_KERNEL);
+	    sizeof(struct app_pinfo) * app_req.num_ports), GFP_KERNEL);
+
 	if (!app_reply) {
 		SET_DID_STATUS(bsg_reply->result, DID_ERROR);
 		rval = -1;
 	} else {
 		struct fc_port	*fcport = NULL, *tf;
-		uint32_t	pcnt = 0;
 
 		list_for_each_entry_safe(fcport, tf, &vha->vp_fcports, list) {
 			if (!(fcport->flags & FCF_FCSP_DEVICE))
@@ -924,7 +891,7 @@
 			    "APP request entry - portid=%06x.\n", tdid.b24);
 
 			/* Ran out of space */
-			if (pcnt > app_req.num_ports)
+			if (pcnt >= app_req.num_ports)
 				break;
 
 			if (tdid.b24 != 0 && tdid.b24 != fcport->d_id.b24)
@@ -933,6 +900,20 @@
 			app_reply->ports[pcnt].rekey_count =
 				fcport->edif.rekey_cnt;
 
+			if (fcport->scan_state != QLA_FCPORT_FOUND)
+				continue;
+
+			if (fcport->port_type == FCT_UNKNOWN && !fcport->fc4_features)
+				rval = qla24xx_async_gffid(vha, fcport, true);
+
+			if (!rval &&
+			    !(fcport->fc4_features & FC4_FF_TARGET ||
+			      fcport->port_type &
+			      (FCT_TARGET | FCT_NVME_TARGET)))
+				continue;
+
+			rval = 0;
+
 			app_reply->ports[pcnt].remote_type =
 				VND_CMD_RTYPE_UNKNOWN;
 			if (fcport->port_type & (FCT_NVME_TARGET | FCT_TARGET))
@@ -981,9 +962,11 @@
 		SET_DID_STATUS(bsg_reply->result, DID_OK);
 	}
 
-	sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
-	    bsg_job->reply_payload.sg_cnt, app_reply,
-	    sizeof(struct app_pinfo_reply) + sizeof(struct app_pinfo) * num_cnt);
+	bsg_job->reply_len = sizeof(struct fc_bsg_reply);
+	bsg_reply->reply_payload_rcv_len = sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
+							       bsg_job->reply_payload.sg_cnt,
+							       app_reply,
+							       sizeof(struct app_pinfo_reply) + sizeof(struct app_pinfo) * pcnt);
 
 	kfree(app_reply);
 
@@ -1000,10 +983,11 @@
 {
 	int32_t			rval = 0;
 	struct fc_bsg_reply	*bsg_reply = bsg_job->reply;
-	uint32_t ret_size, size;
+	uint32_t size;
 
 	struct app_sinfo_req	app_req;
 	struct app_stats_reply	*app_reply;
+	uint32_t pcnt = 0;
 
 	sg_copy_to_buffer(bsg_job->request_payload.sg_list,
 	    bsg_job->request_payload.sg_cnt, &app_req,
@@ -1019,22 +1003,16 @@
 	size = sizeof(struct app_stats_reply) +
 	    (sizeof(struct app_sinfo) * app_req.num_ports);
 
-	if (size > bsg_job->reply_payload.payload_len)
-		ret_size = bsg_job->reply_payload.payload_len;
-	else
-		ret_size = size;
-
 	app_reply = kzalloc(size, GFP_KERNEL);
 	if (!app_reply) {
 		SET_DID_STATUS(bsg_reply->result, DID_ERROR);
 		rval = -1;
 	} else {
 		struct fc_port	*fcport = NULL, *tf;
-		uint32_t	pcnt = 0;
 
 		list_for_each_entry_safe(fcport, tf, &vha->vp_fcports, list) {
 			if (fcport->edif.enable) {
-				if (pcnt > app_req.num_ports)
+				if (pcnt >= app_req.num_ports)
 					break;
 
 				app_reply->elem[pcnt].rekey_count =
@@ -1054,9 +1032,11 @@
 		SET_DID_STATUS(bsg_reply->result, DID_OK);
 	}
 
+	bsg_job->reply_len = sizeof(struct fc_bsg_reply);
 	bsg_reply->reply_payload_rcv_len =
 	    sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
-	       bsg_job->reply_payload.sg_cnt, app_reply, ret_size);
+	       bsg_job->reply_payload.sg_cnt, app_reply,
+	       sizeof(struct app_stats_reply) + (sizeof(struct app_sinfo) * pcnt));
 
 	kfree(app_reply);
 
@@ -1130,8 +1110,7 @@
 		    __func__,
 		    bsg_request->rqst_data.h_vendor.vendor_cmd[1]);
 		rval = EXT_STATUS_INVALID_PARAM;
-		bsg_job->reply_len = sizeof(struct fc_bsg_reply);
-		SET_DID_STATUS(bsg_reply->result, DID_ERROR);
+		done = false;
 		break;
 	}
 
@@ -1299,6 +1278,8 @@
 
 #define QLA_SA_UPDATE_FLAGS_RX_KEY      0x0
 #define QLA_SA_UPDATE_FLAGS_TX_KEY      0x2
+#define EDIF_MSLEEP_INTERVAL 100
+#define EDIF_RETRY_COUNT  50
 
 int
 qla24xx_sadb_update(struct bsg_job *bsg_job)
@@ -1311,9 +1292,10 @@
 	struct edif_list_entry *edif_entry = NULL;
 	int			found = 0;
 	int			rval = 0;
-	int result = 0;
+	int result = 0, cnt;
 	struct qla_sa_update_frame sa_frame;
 	struct srb_iocb *iocb_cmd;
+	port_id_t portid;
 
 	ql_dbg(ql_dbg_edif + ql_dbg_verbose, vha, 0x911d,
 	    "%s entered, vha: 0x%p\n", __func__, vha);
@@ -1330,14 +1312,19 @@
 		goto done;
 	}
 
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		ql_log(ql_log_warn, vha, 0x70a1, "App not started\n");
 		rval = -EIO;
 		SET_DID_STATUS(bsg_reply->result, DID_ERROR);
 		goto done;
 	}
 
-	fcport = qla2x00_find_fcport_by_pid(vha, &sa_frame.port_id);
+	/* silent unaligned access warning */
+	portid.b.domain = sa_frame.port_id.b.domain;
+	portid.b.area   = sa_frame.port_id.b.area;
+	portid.b.al_pa  = sa_frame.port_id.b.al_pa;
+
+	fcport = qla2x00_find_fcport_by_pid(vha, &portid);
 	if (fcport) {
 		found = 1;
 		if (sa_frame.flags == QLA_SA_UPDATE_FLAGS_TX_KEY)
@@ -1546,11 +1533,23 @@
 	sp->done = qla2x00_bsg_job_done;
 	iocb_cmd = &sp->u.iocb_cmd;
 	iocb_cmd->u.sa_update.sa_frame  = sa_frame;
-
+	cnt = 0;
+retry:
 	rval = qla2x00_start_sp(sp);
-	if (rval != QLA_SUCCESS) {
+	switch (rval) {
+	case QLA_SUCCESS:
+		break;
+	case EAGAIN:
+		msleep(EDIF_MSLEEP_INTERVAL);
+		cnt++;
+		if (cnt < EDIF_RETRY_COUNT)
+			goto retry;
+
+		fallthrough;
+	default:
 		ql_log(ql_dbg_edif, vha, 0x70e3,
-		    "qla2x00_start_sp failed=%d.\n", rval);
+		       "%s qla2x00_start_sp failed=%d.\n",
+		       __func__, rval);
 
 		qla2x00_rel_sp(sp);
 		rval = -EIO;
@@ -1651,6 +1650,40 @@
 	spin_unlock_irqrestore(&vha->pur_cinfo.pur_lock, flags);
 }
 
+static void qla_enode_clear(scsi_qla_host_t *vha, port_id_t portid)
+{
+	unsigned    long flags;
+	struct enode    *e, *tmp;
+	struct purexevent   *purex;
+	LIST_HEAD(enode_list);
+
+	if (vha->pur_cinfo.enode_flags != ENODE_ACTIVE) {
+		ql_dbg(ql_dbg_edif, vha, 0x09102,
+		       "%s enode not active\n", __func__);
+		return;
+	}
+	spin_lock_irqsave(&vha->pur_cinfo.pur_lock, flags);
+	list_for_each_entry_safe(e, tmp, &vha->pur_cinfo.head, list) {
+		purex = &e->u.purexinfo;
+		if (purex->pur_info.pur_sid.b24 == portid.b24) {
+			ql_dbg(ql_dbg_edif, vha, 0x911d,
+			    "%s free ELS sid=%06x. xchg %x, nb=%xh\n",
+			    __func__, portid.b24,
+			    purex->pur_info.pur_rx_xchg_address,
+			    purex->pur_info.pur_bytes_rcvd);
+
+			list_del_init(&e->list);
+			list_add_tail(&e->list, &enode_list);
+		}
+	}
+	spin_unlock_irqrestore(&vha->pur_cinfo.pur_lock, flags);
+
+	list_for_each_entry_safe(e, tmp, &enode_list, list) {
+		list_del_init(&e->list);
+		qla_enode_free(vha, e);
+	}
+}
+
 /*
  *  allocate enode struct and populate buffer
  *  returns: enode pointer with buffers
@@ -1695,41 +1728,25 @@
 qla_enode_find(scsi_qla_host_t *vha, uint32_t ntype, uint32_t p1, uint32_t p2)
 {
 	struct enode		*node_rtn = NULL;
-	struct enode		*list_node = NULL;
+	struct enode		*list_node, *q;
 	unsigned long		flags;
-	struct list_head	*pos, *q;
 	uint32_t		sid;
-	uint32_t		rw_flag;
 	struct purexevent	*purex;
 
 	/* secure the list from moving under us */
 	spin_lock_irqsave(&vha->pur_cinfo.pur_lock, flags);
 
-	list_for_each_safe(pos, q, &vha->pur_cinfo.head) {
-		list_node = list_entry(pos, struct enode, list);
+	list_for_each_entry_safe(list_node, q, &vha->pur_cinfo.head, list) {
 
 		/* node type determines what p1 and p2 are */
 		purex = &list_node->u.purexinfo;
 		sid = p1;
-		rw_flag = p2;
 
 		if (purex->pur_info.pur_sid.b24 == sid) {
-			if (purex->pur_info.pur_pend == 1 &&
-			    rw_flag == PUR_GET) {
-				/*
-				 * if the receive is in progress
-				 * and its a read/get then can't
-				 * transfer yet
-				 */
-				ql_dbg(ql_dbg_edif, vha, 0x9106,
-				    "%s purex xfer in progress for sid=%x\n",
-				    __func__, sid);
-			} else {
-				/* found it and its complete */
-				node_rtn = list_node;
-				list_del(pos);
-				break;
-			}
+			/* found it and its complete */
+			node_rtn = list_node;
+			list_del(&list_node->list);
+			break;
 		}
 	}
 
@@ -1814,7 +1831,7 @@
 void
 qla_edb_init(scsi_qla_host_t *vha)
 {
-	if (vha->e_dbell.db_flags == EDB_ACTIVE) {
+	if (DBELL_ACTIVE(vha)) {
 		/* list already init'd - error */
 		ql_dbg(ql_dbg_edif, vha, 0x09102,
 		    "edif db already initialized, cannot reinit\n");
@@ -1850,6 +1867,57 @@
 	node->ntype = N_UNDEF;
 }
 
+static void qla_edb_clear(scsi_qla_host_t *vha, port_id_t portid)
+{
+	unsigned long flags;
+	struct edb_node *e, *tmp;
+	port_id_t sid;
+	LIST_HEAD(edb_list);
+
+	if (DBELL_INACTIVE(vha)) {
+		/* doorbell list not enabled */
+		ql_dbg(ql_dbg_edif, vha, 0x09102,
+		       "%s doorbell not enabled\n", __func__);
+		return;
+	}
+
+	/* grab lock so list doesn't move */
+	spin_lock_irqsave(&vha->e_dbell.db_lock, flags);
+	list_for_each_entry_safe(e, tmp, &vha->e_dbell.head, list) {
+		switch (e->ntype) {
+		case VND_CMD_AUTH_STATE_NEEDED:
+		case VND_CMD_AUTH_STATE_SESSION_SHUTDOWN:
+			sid = e->u.plogi_did;
+			break;
+		case VND_CMD_AUTH_STATE_ELS_RCVD:
+			sid = e->u.els_sid;
+			break;
+		case VND_CMD_AUTH_STATE_SAUPDATE_COMPL:
+			/* app wants to see this  */
+			continue;
+		default:
+			ql_log(ql_log_warn, vha, 0x09102,
+			       "%s unknown node type: %x\n", __func__, e->ntype);
+			sid.b24 = 0;
+			break;
+		}
+		if (sid.b24 == portid.b24) {
+			ql_dbg(ql_dbg_edif, vha, 0x910f,
+			       "%s free doorbell event : node type = %x %p\n",
+			       __func__, e->ntype, e);
+			list_del_init(&e->list);
+			list_add_tail(&e->list, &edb_list);
+		}
+	}
+	spin_unlock_irqrestore(&vha->e_dbell.db_lock, flags);
+
+	list_for_each_entry_safe(e, tmp, &edb_list, list) {
+		qla_edb_node_free(vha, e);
+		list_del_init(&e->list);
+		kfree(e);
+	}
+}
+
 /* function called when app is stopping */
 
 void
@@ -1858,7 +1926,7 @@
 	unsigned long flags;
 	struct edb_node *node, *q;
 
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		/* doorbell list not enabled */
 		ql_dbg(ql_dbg_edif, vha, 0x09102,
 		    "%s doorbell not enabled\n", __func__);
@@ -1909,7 +1977,7 @@
 {
 	unsigned long		flags;
 
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		/* doorbell list not enabled */
 		ql_dbg(ql_dbg_edif, vha, 0x09102,
 		    "%s doorbell not enabled\n", __func__);
@@ -1940,7 +2008,7 @@
 		return;
 	}
 
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		if (fcport)
 			fcport->edif.auth_state = dbtype;
 		/* doorbell list not enabled */
@@ -2035,7 +2103,7 @@
 	struct qla_hw_data *ha = vha->hw;
 
 	if (!vha->vp_idx && N2N_TOPO(ha) && ha->flags.n2n_fw_acc_sec) {
-		if (vha->e_dbell.db_flags != EDB_ACTIVE &&
+		if (DBELL_INACTIVE(vha) &&
 		    ha->edif_post_stop_cnt_down) {
 			ha->edif_post_stop_cnt_down--;
 
@@ -2073,7 +2141,7 @@
 	sz = 256;
 
 	/* stop new threads from waiting if we're not init'd */
-	if (vha->e_dbell.db_flags != EDB_ACTIVE) {
+	if (DBELL_INACTIVE(vha)) {
 		ql_dbg(ql_dbg_edif + ql_dbg_verbose, vha, 0x09122,
 		    "%s error - edif db not enabled\n", __func__);
 		return 0;
@@ -2137,7 +2205,9 @@
 
 static void qla_noop_sp_done(srb_t *sp, int res)
 {
-	sp->free(sp);
+	sp->fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 /*
@@ -2160,7 +2230,8 @@
 	if (!sa_ctl) {
 		ql_dbg(ql_dbg_edif, vha, 0x70e6,
 		    "sa_ctl allocation failed\n");
-		return -ENOMEM;
+		rval = -ENOMEM;
+		return rval;
 	}
 
 	fcport = sa_ctl->fcport;
@@ -2170,7 +2241,8 @@
 	if (!sp) {
 		ql_dbg(ql_dbg_edif, vha, 0x70e6,
 		 "SRB allocation failed\n");
-		return -ENOMEM;
+		rval = -ENOMEM;
+		goto done;
 	}
 
 	fcport->flags |= FCF_ASYNC_SENT;
@@ -2199,10 +2271,17 @@
 
 	rval = qla2x00_start_sp(sp);
 
-	if (rval != QLA_SUCCESS)
-		rval = QLA_FUNCTION_FAILED;
+	if (rval != QLA_SUCCESS) {
+		goto done_free_sp;
+	}
 
 	return rval;
+done_free_sp:
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
+	fcport->flags &= ~FCF_ASYNC_SENT;
+done:
+	fcport->flags &= ~FCF_ASYNC_ACTIVE;
+	return rval;
 }
 
 void qla24xx_sa_update_iocb(srb_t *sp, struct sa_update_28xx *sa_update_iocb)
@@ -2357,7 +2436,7 @@
 		return;
 	}
 
-	if (totlen > MAX_PAYLOAD) {
+	if (totlen > ELS_MAX_PAYLOAD) {
 		ql_dbg(ql_dbg_edif, vha, 0x0910d,
 		    "%s WARNING: verbose ELS frame received (totlen=%x)\n",
 		    __func__, totlen);
@@ -2387,7 +2466,6 @@
 
 	purex = &ptr->u.purexinfo;
 	purex->pur_info.pur_sid = a.did;
-	purex->pur_info.pur_pend = 0;
 	purex->pur_info.pur_bytes_rcvd = totlen;
 	purex->pur_info.pur_rx_xchg_address = le32_to_cpu(p->rx_xchg_addr);
 	purex->pur_info.pur_nphdl = le16_to_cpu(p->nport_handle);
@@ -2419,8 +2497,7 @@
 
 	fcport = qla2x00_find_fcport_by_pid(host, &purex->pur_info.pur_sid);
 
-	if (host->e_dbell.db_flags != EDB_ACTIVE ||
-	    (fcport && EDIF_SESSION_DOWN(fcport))) {
+	if (DBELL_INACTIVE(vha)) {
 		ql_dbg(ql_dbg_edif, host, 0x0910c, "%s e_dbell.db_flags =%x %06x\n",
 		    __func__, host->e_dbell.db_flags,
 		    fcport ? fcport->d_id.b24 : 0);
@@ -2430,13 +2507,29 @@
 		return;
 	}
 
+	if (fcport && EDIF_SESSION_DOWN(fcport)) {
+		ql_dbg(ql_dbg_edif, host, 0x13b6,
+		    "%s terminate exchange. Send logo to 0x%x\n",
+		    __func__, a.did.b24);
+
+		a.tx_byte_count = a.tx_len = 0;
+		a.tx_addr = 0;
+		a.control_flags = EPD_RX_XCHG;  /* EPD_RX_XCHG = terminate cmd */
+		qla_els_reject_iocb(host, (*rsp)->qpair, &a);
+		qla_enode_free(host, ptr);
+		/* send logo to let remote port knows to tear down session */
+		fcport->send_els_logo = 1;
+		qlt_schedule_sess_for_deletion(fcport);
+		return;
+	}
+
 	/* add the local enode to the list */
 	qla_enode_add(host, ptr);
 
 	ql_dbg(ql_dbg_edif, host, 0x0910c,
 	    "%s COMPLETE purex->pur_info.pur_bytes_rcvd =%xh s:%06x -> d:%06x xchg=%xh\n",
 	    __func__, purex->pur_info.pur_bytes_rcvd, purex->pur_info.pur_sid.b24,
-	    purex->pur_info.pur_did.b24, p->rx_xchg_addr);
+	    purex->pur_info.pur_did.b24, purex->pur_info.pur_rx_xchg_address);
 
 	qla_edb_eventcreate(host, VND_CMD_AUTH_STATE_ELS_RCVD, sid, 0, NULL);
 }
@@ -2805,6 +2898,13 @@
 
 	tot_dsds = nseg;
 	req_cnt = qla24xx_calc_iocbs(vha, tot_dsds);
+
+	sp->iores.res_type = RESOURCE_IOCB | RESOURCE_EXCH;
+	sp->iores.exch_cnt = 1;
+	sp->iores.iocb_cnt = req_cnt;
+	if (qla_get_fw_resources(sp->qpair, &sp->iores))
+		goto queuing_error;
+
 	if (req->cnt < (req_cnt + 2)) {
 		cnt = IS_SHADOW_REG_CAPABLE(ha) ? *req->out_ptr :
 		    rd_reg_dword(req->req_q_out);
@@ -2996,6 +3096,7 @@
 		mempool_free(sp->u.scmd.ct6_ctx, ha->ctx_mempool);
 		sp->u.scmd.ct6_ctx = NULL;
 	}
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(lock, flags);
 
 	return QLA_FUNCTION_FAILED;
@@ -3139,18 +3240,14 @@
 /* release any sadb entries -- only done at teardown */
 void qla_edif_sadb_release(struct qla_hw_data *ha)
 {
-	struct list_head *pos;
-	struct list_head *tmp;
-	struct edif_sa_index_entry *entry;
+	struct edif_sa_index_entry *entry, *tmp;
 
-	list_for_each_safe(pos, tmp, &ha->sadb_rx_index_list) {
-		entry = list_entry(pos, struct edif_sa_index_entry, next);
+	list_for_each_entry_safe(entry, tmp, &ha->sadb_rx_index_list, next) {
 		list_del(&entry->next);
 		kfree(entry);
 	}
 
-	list_for_each_safe(pos, tmp, &ha->sadb_tx_index_list) {
-		entry = list_entry(pos, struct edif_sa_index_entry, next);
+	list_for_each_entry_safe(entry, tmp, &ha->sadb_tx_index_list, next) {
 		list_del(&entry->next);
 		kfree(entry);
 	}
@@ -3326,7 +3423,7 @@
 	fc_port_t *fcport = NULL;
 	struct qla_hw_data *ha = vha->hw;
 	srb_t *sp;
-	int rval =  (DID_ERROR << 16);
+	int rval =  (DID_ERROR << 16), cnt;
 	port_id_t d_id;
 	struct qla_bsg_auth_els_request *p =
 	    (struct qla_bsg_auth_els_request *)bsg_job->request;
@@ -3348,7 +3445,7 @@
 	if (qla_bsg_check(vha, bsg_job, fcport))
 		return 0;
 
-	if (fcport->loop_id == FC_NO_LOOP_ID) {
+	if (EDIF_SESS_DELETE(fcport)) {
 		ql_dbg(ql_dbg_edif, vha, 0x910d,
 		    "%s ELS code %x, no loop id.\n", __func__,
 		    bsg_request->rqst_data.r_els.els_code);
@@ -3417,17 +3514,26 @@
 	sp->free = qla2x00_bsg_sp_free;
 	sp->done = qla2x00_bsg_job_done;
 
+	cnt = 0;
+retry:
 	rval = qla2x00_start_sp(sp);
-
-	ql_dbg(ql_dbg_edif, vha, 0x700a,
-	    "%s %s %8phN xchg %x ctlflag %x hdl %x reqlen %xh bsg ptr %p\n",
-	    __func__, sc_to_str(p->e.sub_cmd), fcport->port_name,
-	    p->e.extra_rx_xchg_address, p->e.extra_control_flags,
-	    sp->handle, sp->remap.req.len, bsg_job);
-
-	if (rval != QLA_SUCCESS) {
+	switch (rval) {
+	case QLA_SUCCESS:
+		ql_dbg(ql_dbg_edif, vha, 0x700a,
+		       "%s %s %8phN xchg %x ctlflag %x hdl %x reqlen %xh bsg ptr %p\n",
+		       __func__, sc_to_str(p->e.sub_cmd), fcport->port_name,
+		       p->e.extra_rx_xchg_address, p->e.extra_control_flags,
+		       sp->handle, sp->remap.req.len, bsg_job);
+		break;
+	case EAGAIN:
+		msleep(EDIF_MSLEEP_INTERVAL);
+		cnt++;
+		if (cnt < EDIF_RETRY_COUNT)
+			goto retry;
+		fallthrough;
+	default:
 		ql_log(ql_log_warn, vha, 0x700e,
-		    "qla2x00_start_sp failed = %d\n", rval);
+		    "%s qla2x00_start_sp failed = %d\n", __func__, rval);
 		SET_DID_STATUS(bsg_reply->result, DID_IMM_RETRY);
 		rval = -EIO;
 		goto done_free_remap_rsp;
@@ -3449,7 +3555,7 @@
 
 void qla_edif_sess_down(struct scsi_qla_host *vha, struct fc_port *sess)
 {
-	if (sess->edif.app_sess_online && vha->e_dbell.db_flags & EDB_ACTIVE) {
+	if (sess->edif.app_sess_online && DBELL_ACTIVE(vha)) {
 		ql_dbg(ql_dbg_disc, vha, 0xf09c,
 			"%s: sess %8phN send port_offline event\n",
 			__func__, sess->port_name);
@@ -3459,3 +3565,12 @@
 		qla2x00_post_aen_work(vha, FCH_EVT_PORT_OFFLINE, sess->d_id.b24);
 	}
 }
+
+void qla_edif_clear_appdata(struct scsi_qla_host *vha, struct fc_port *fcport)
+{
+	if (!(fcport->flags & FCF_FCSP_DEVICE))
+		return;
+
+	qla_edb_clear(vha, fcport->d_id);
+	qla_enode_clear(vha, fcport->d_id);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_edif.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_edif.h
@@ -41,9 +41,12 @@
 };
 
 enum db_flags_t {
-	EDB_ACTIVE = 0x1,
+	EDB_ACTIVE = BIT_0,
 };
 
+#define DBELL_ACTIVE(_v) (_v->e_dbell.db_flags & EDB_ACTIVE)
+#define DBELL_INACTIVE(_v) (!(_v->e_dbell.db_flags & EDB_ACTIVE))
+
 struct edif_dbell {
 	enum db_flags_t		db_flags;
 	spinlock_t		db_lock;
@@ -93,7 +96,6 @@
 };
 
 #define        NUM_ENTRIES     256
-#define        MAX_PAYLOAD     1024
 #define        PUR_GET         1
 
 struct dinfo {
@@ -102,7 +104,6 @@
 };
 
 struct pur_ninfo {
-	unsigned int	pur_pend:1;
 	port_id_t       pur_sid;
 	port_id_t	pur_did;
 	uint8_t		vp_idx;
@@ -128,9 +129,19 @@
 	} u;
 };
 
+#define RX_ELS_SIZE (roundup(sizeof(struct enode) + ELS_MAX_PAYLOAD, SMP_CACHE_BYTES))
+
 #define EDIF_SESSION_DOWN(_s) \
 	(qla_ini_mode_enabled(_s->vha) && (_s->disc_state == DSC_DELETE_PEND || \
 	 _s->disc_state == DSC_DELETED || \
 	 !_s->edif.app_sess_online))
 
+#define EDIF_NEGOTIATION_PENDING(_fcport) \
+	(DBELL_ACTIVE(_fcport->vha) && \
+	 (_fcport->disc_state == DSC_LOGIN_AUTH_PEND))
+
+#define EDIF_SESS_DELETE(_s) \
+	(qla_ini_mode_enabled(_s->vha) && (_s->disc_state == DSC_DELETE_PEND || \
+	 _s->disc_state == DSC_DELETED))
+
 #endif	/* __QLA_EDIF_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_edif_bsg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_edif_bsg.h
@@ -8,7 +8,7 @@
 #define __QLA_EDIF_BSG_H
 
 /* BSG Vendor specific commands */
-#define	ELS_MAX_PAYLOAD		1024
+#define	ELS_MAX_PAYLOAD		2112
 #ifndef	WWN_SIZE
 #define WWN_SIZE		8
 #endif
@@ -217,4 +217,6 @@
 
 #define RX_DELAY_DELETE_TIMEOUT 20
 
+#define FCH_EVT_VENDOR_UNIQUE_VPORT_DOWN  1
+
 #endif	/* QLA_EDIF_BSG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_fw.h
@@ -807,7 +807,7 @@
 #define EPD_ELS_COMMAND		(0 << 13)
 #define EPD_ELS_ACC		(1 << 13)
 #define EPD_ELS_RJT		(2 << 13)
-#define EPD_RX_XCHG		(3 << 13)
+#define EPD_RX_XCHG		(3 << 13)  /* terminate exchange */
 #define ECF_CLR_PASSTHRU_PEND	BIT_12
 #define ECF_INCL_FRAME_HDR	BIT_11
 #define ECF_SEC_LOGIN		BIT_3
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_gbl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_gbl.h
@@ -11,6 +11,9 @@
 /*
  * Global Function Prototypes in qla_init.c source file.
  */
+int  qla2x00_alloc_fce_trace(scsi_qla_host_t *);
+void qla2x00_free_fce_trace(struct qla_hw_data *ha);
+void qla_enable_fce_trace(scsi_qla_host_t *);
 extern int qla2x00_initialize_adapter(scsi_qla_host_t *);
 extern int qla24xx_post_prli_work(struct scsi_qla_host *vha, fc_port_t *fcport);
 
@@ -44,7 +47,7 @@
 extern int qla2x00_local_device_login(scsi_qla_host_t *, fc_port_t *);
 
 extern int qla24xx_els_dcmd_iocb(scsi_qla_host_t *, int, port_id_t);
-extern int qla24xx_els_dcmd2_iocb(scsi_qla_host_t *, int, fc_port_t *, bool);
+extern int qla24xx_els_dcmd2_iocb(scsi_qla_host_t *, int, fc_port_t *);
 extern void qla2x00_els_dcmd2_free(scsi_qla_host_t *vha,
 				   struct els_plogi *els_plogi);
 
@@ -69,9 +72,7 @@
 extern int qla2x00_async_prlo(struct scsi_qla_host *, fc_port_t *);
 extern int qla2x00_async_adisc(struct scsi_qla_host *, fc_port_t *,
     uint16_t *);
-extern int qla2x00_async_tm_cmd(fc_port_t *, uint32_t, uint32_t, uint32_t);
-extern void qla2x00_async_login_done(struct scsi_qla_host *, fc_port_t *,
-    uint16_t *);
+extern int qla2x00_async_tm_cmd(fc_port_t *, uint32_t, uint64_t, uint32_t);
 struct qla_work_evt *qla2x00_alloc_work(struct scsi_qla_host *,
     enum qla_work_type);
 extern int qla24xx_async_gnl(struct scsi_qla_host *, fc_port_t *);
@@ -142,7 +143,10 @@
 void qla2x00_release_all_sadb(struct scsi_qla_host *vha, struct fc_port *fcport);
 int qla_edif_process_els(scsi_qla_host_t *vha, struct bsg_job *bsgjob);
 void qla_edif_sess_down(struct scsi_qla_host *vha, struct fc_port *sess);
+void qla_edif_clear_appdata(struct scsi_qla_host *vha,
+			    struct fc_port *fcport);
 const char *sc_to_str(uint16_t cmd);
+void qla_adjust_iocb_limit(scsi_qla_host_t *vha);
 
 /*
  * Global Data in qla_os.c source file.
@@ -171,7 +175,6 @@
 extern int ql2xgffidenable;
 extern int ql2xenabledif;
 extern int ql2xenablehba_err_chk;
-extern int ql2xtargetreset;
 extern int ql2xdontresethba;
 extern uint64_t ql2xmaxlun;
 extern int ql2xmdcapmask;
@@ -191,6 +194,8 @@
 extern int ql2xsecenable;
 extern int ql2xenforce_iocb_limit;
 extern int ql2xabts_wait_nvme;
+extern int ql2xrspq_follow_inptr;
+extern int ql2xrspq_follow_inptr_legacy;
 
 extern int qla2x00_loop_reset(scsi_qla_host_t *);
 extern void qla2x00_abort_all_cmds(scsi_qla_host_t *, int);
@@ -275,7 +280,6 @@
 extern scsi_qla_host_t *qla24xx_create_vhost(struct fc_vport *);
 
 extern void qla2x00_sp_free_dma(srb_t *sp);
-extern char *qla2x00_get_fw_version_str(struct scsi_qla_host *, char *);
 
 extern void qla2x00_mark_device_lost(scsi_qla_host_t *, fc_port_t *, int);
 extern void qla2x00_mark_all_devices_lost(scsi_qla_host_t *);
@@ -315,7 +319,8 @@
 extern int qla24xx_dif_start_scsi(srb_t *);
 extern int qla2x00_start_bidir(srb_t *, struct scsi_qla_host *, uint32_t);
 extern int qla2xxx_dif_start_scsi_mq(srb_t *);
-extern void qla2x00_init_timer(srb_t *sp, unsigned long tmo);
+extern void qla2x00_init_async_sp(srb_t *sp, unsigned long tmo,
+				  void (*done)(struct srb *, int));
 extern unsigned long qla2x00_get_async_timeout(struct scsi_qla_host *);
 
 extern void *qla2x00_alloc_iocbs(struct scsi_qla_host *, srb_t *);
@@ -331,6 +336,8 @@
 extern int qla24xx_configure_prot_mode(srb_t *, uint16_t *);
 extern int qla24xx_issue_sa_replace_iocb(scsi_qla_host_t *vha,
 	struct qla_work_evt *e);
+void qla2x00_sp_release(struct kref *kref);
+void qla2x00_els_dcmd2_iocb_timeout(void *data);
 
 /*
  * Global Function Prototypes in qla_mbx.c source file.
@@ -429,7 +436,8 @@
 qla2x00_get_resource_cnts(scsi_qla_host_t *);
 
 extern int
-qla2x00_get_fcal_position_map(scsi_qla_host_t *ha, char *pos_map);
+qla2x00_get_fcal_position_map(scsi_qla_host_t *ha, char *pos_map,
+		u8 *num_entries);
 
 extern int
 qla2x00_get_link_status(scsi_qla_host_t *, uint16_t, struct link_statistics *,
@@ -604,7 +612,6 @@
 /*
  * Global Function Prototypes in qla_sup.c source file.
  */
-extern void qla2x00_release_nvram_protection(scsi_qla_host_t *);
 extern int qla24xx_read_flash_data(scsi_qla_host_t *, uint32_t *,
     uint32_t, uint32_t);
 extern uint8_t *qla2x00_read_nvram_data(scsi_qla_host_t *, void *, uint32_t,
@@ -719,7 +726,7 @@
 void qla24xx_handle_gpsc_event(scsi_qla_host_t *, struct event_arg *);
 int qla2x00_mgmt_svr_login(scsi_qla_host_t *);
 void qla24xx_handle_gffid_event(scsi_qla_host_t *vha, struct event_arg *ea);
-int qla24xx_async_gffid(scsi_qla_host_t *vha, fc_port_t *fcport);
+int qla24xx_async_gffid(scsi_qla_host_t *vha, fc_port_t *fcport, bool);
 int qla24xx_async_gpnft(scsi_qla_host_t *, u8, srb_t *);
 void qla24xx_async_gpnft_done(scsi_qla_host_t *, srb_t *);
 void qla24xx_async_gnnft_done(scsi_qla_host_t *, srb_t *);
@@ -774,12 +781,6 @@
 extern int qla25xx_delete_req_que(struct scsi_qla_host *, struct req_que *);
 extern int qla25xx_delete_rsp_que(struct scsi_qla_host *, struct rsp_que *);
 extern int qla25xx_delete_queues(struct scsi_qla_host *);
-extern uint16_t qla24xx_rd_req_reg(struct qla_hw_data *, uint16_t);
-extern uint16_t qla25xx_rd_req_reg(struct qla_hw_data *, uint16_t);
-extern void qla24xx_wrt_req_reg(struct qla_hw_data *, uint16_t, uint16_t);
-extern void qla25xx_wrt_req_reg(struct qla_hw_data *, uint16_t, uint16_t);
-extern void qla25xx_wrt_rsp_reg(struct qla_hw_data *, uint16_t, uint16_t);
-extern void qla24xx_wrt_rsp_reg(struct qla_hw_data *, uint16_t, uint16_t);
 
 /* qlafx00 related functions */
 extern int qlafx00_pci_config(struct scsi_qla_host *);
@@ -816,7 +817,6 @@
 extern void qlafx00_fxdisc_iocb(srb_t *, struct fxdisc_entry_fx00 *);
 extern void qlafx00_timer_routine(scsi_qla_host_t *);
 extern int qlafx00_rescan_isp(scsi_qla_host_t *);
-extern int qlafx00_loop_reset(scsi_qla_host_t *vha);
 
 /* qla82xx related functions */
 
@@ -865,8 +865,6 @@
 extern void qla82xx_set_drv_active(scsi_qla_host_t *);
 extern int qla82xx_wr_32(struct qla_hw_data *, ulong, u32);
 extern int qla82xx_rd_32(struct qla_hw_data *, ulong);
-extern int qla82xx_rdmem(struct qla_hw_data *, u64, void *, int);
-extern int qla82xx_wrmem(struct qla_hw_data *, u64, void *, int);
 
 /* ISP 8021 IDC */
 extern void qla82xx_clear_drv_active(struct qla_hw_data *);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_gs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_gs.c
@@ -529,7 +529,6 @@
 		if (!e)
 			goto err2;
 
-		del_timer(&sp->u.iocb_cmd.timer);
 		e->u.iosb.sp = sp;
 		qla2x00_post_work(vha, e);
 		return;
@@ -556,8 +555,8 @@
 			sp->u.iocb_cmd.u.ctarg.rsp = NULL;
 		}
 
-		sp->free(sp);
-
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
 		return;
 	}
 
@@ -592,13 +591,15 @@
 	if (!vha->flags.online)
 		goto done;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_CT_PTHRU_CMD;
 	sp->name = "rft_id";
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_sns_sp_done);
 
 	sp->u.iocb_cmd.u.ctarg.req = dma_alloc_coherent(&vha->hw->pdev->dev,
 	    sizeof(struct ct_sns_pkt), &sp->u.iocb_cmd.u.ctarg.req_dma,
@@ -638,8 +639,6 @@
 	sp->u.iocb_cmd.u.ctarg.req_size = RFT_ID_REQ_SIZE;
 	sp->u.iocb_cmd.u.ctarg.rsp_size = RFT_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	sp->done = qla2x00_async_sns_sp_done;
 
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s - hdl=%x portid %06x.\n",
@@ -653,7 +652,8 @@
 	}
 	return rval;
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
@@ -676,8 +676,7 @@
 		return (QLA_SUCCESS);
 	}
 
-	return qla_async_rffid(vha, &vha->d_id, qlt_rff_id(vha),
-	    FC4_TYPE_FCP_SCSI);
+	return qla_async_rffid(vha, &vha->d_id, qlt_rff_id(vha), type);
 }
 
 static int qla_async_rffid(scsi_qla_host_t *vha, port_id_t *d_id,
@@ -688,13 +687,15 @@
 	srb_t *sp;
 	struct ct_sns_pkt *ct_sns;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_CT_PTHRU_CMD;
 	sp->name = "rff_id";
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_sns_sp_done);
 
 	sp->u.iocb_cmd.u.ctarg.req = dma_alloc_coherent(&vha->hw->pdev->dev,
 	    sizeof(struct ct_sns_pkt), &sp->u.iocb_cmd.u.ctarg.req_dma,
@@ -727,13 +728,11 @@
 	/* Prepare CT arguments -- port_id, FC-4 feature, FC-4 type */
 	ct_req->req.rff_id.port_id = port_id_to_be_id(*d_id);
 	ct_req->req.rff_id.fc4_feature = fc4feature;
-	ct_req->req.rff_id.fc4_type = fc4type;		/* SCSI - FCP */
+	ct_req->req.rff_id.fc4_type = fc4type;		/* SCSI-FCP or FC-NVMe */
 
 	sp->u.iocb_cmd.u.ctarg.req_size = RFF_ID_REQ_SIZE;
 	sp->u.iocb_cmd.u.ctarg.rsp_size = RFF_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	sp->done = qla2x00_async_sns_sp_done;
 
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s - hdl=%x portid %06x feature %x type %x.\n",
@@ -749,7 +748,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
@@ -779,13 +779,15 @@
 	srb_t *sp;
 	struct ct_sns_pkt *ct_sns;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_CT_PTHRU_CMD;
 	sp->name = "rnid";
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_sns_sp_done);
 
 	sp->u.iocb_cmd.u.ctarg.req = dma_alloc_coherent(&vha->hw->pdev->dev,
 	    sizeof(struct ct_sns_pkt), &sp->u.iocb_cmd.u.ctarg.req_dma,
@@ -823,9 +825,6 @@
 	sp->u.iocb_cmd.u.ctarg.rsp_size = RNN_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	sp->done = qla2x00_async_sns_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s - hdl=%x portid %06x\n",
 	    sp->name, sp->handle, d_id->b24);
@@ -840,7 +839,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
@@ -886,13 +886,15 @@
 	srb_t *sp;
 	struct ct_sns_pkt *ct_sns;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_CT_PTHRU_CMD;
 	sp->name = "rsnn_nn";
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_sns_sp_done);
 
 	sp->u.iocb_cmd.u.ctarg.req = dma_alloc_coherent(&vha->hw->pdev->dev,
 	    sizeof(struct ct_sns_pkt), &sp->u.iocb_cmd.u.ctarg.req_dma,
@@ -936,9 +938,6 @@
 	sp->u.iocb_cmd.u.ctarg.rsp_size = RSNN_NN_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	sp->done = qla2x00_async_sns_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s - hdl=%x.\n",
 	    sp->name, sp->handle);
@@ -953,7 +952,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
@@ -1595,7 +1595,6 @@
 	unsigned int callopt)
 {
 	struct qla_hw_data *ha = vha->hw;
-	struct init_cb_24xx *icb24 = (void *)ha->init_cb;
 	struct new_utsname *p_sysid = utsname();
 	struct ct_fdmi_hba_attr *eiter;
 	uint16_t alen;
@@ -1616,7 +1615,7 @@
 	eiter->type = cpu_to_be16(FDMI_HBA_MANUFACTURER);
 	alen = scnprintf(
 		eiter->a.manufacturer, sizeof(eiter->a.manufacturer),
-		"%s", "QLogic Corporation");
+		"%s", QLA2XXX_MANUFACTURER);
 	alen += FDMI_ATTR_ALIGNMENT(alen);
 	alen += FDMI_ATTR_TYPELEN(eiter);
 	eiter->len = cpu_to_be16(alen);
@@ -1710,7 +1709,7 @@
 	eiter->type = cpu_to_be16(FDMI_HBA_OPTION_ROM_VERSION);
 	alen = scnprintf(
 		eiter->a.orom_version, sizeof(eiter->a.orom_version),
-		"%d.%02d", ha->bios_revision[1], ha->bios_revision[0]);
+		"%d.%02d", ha->efi_revision[1], ha->efi_revision[0]);
 	alen += FDMI_ATTR_ALIGNMENT(alen);
 	alen += FDMI_ATTR_TYPELEN(eiter);
 	eiter->len = cpu_to_be16(alen);
@@ -1757,8 +1756,8 @@
 	/* MAX CT Payload Length */
 	eiter = entries + size;
 	eiter->type = cpu_to_be16(FDMI_HBA_MAXIMUM_CT_PAYLOAD_LENGTH);
-	eiter->a.max_ct_len = cpu_to_be32(le16_to_cpu(IS_FWI2_CAPABLE(ha) ?
-		icb24->frame_payload_size : ha->init_cb->frame_payload_size));
+	eiter->a.max_ct_len = cpu_to_be32(ha->frame_payload_size >> 2);
+
 	alen = sizeof(eiter->a.max_ct_len);
 	alen += FDMI_ATTR_TYPELEN(eiter);
 	eiter->len = cpu_to_be16(alen);
@@ -1850,7 +1849,6 @@
 	unsigned int callopt)
 {
 	struct qla_hw_data *ha = vha->hw;
-	struct init_cb_24xx *icb24 = (void *)ha->init_cb;
 	struct new_utsname *p_sysid = utsname();
 	char *hostname = p_sysid ?
 		p_sysid->nodename : fc_host_system_hostname(vha->host);
@@ -1902,8 +1900,7 @@
 	/* Max frame size. */
 	eiter = entries + size;
 	eiter->type = cpu_to_be16(FDMI_PORT_MAX_FRAME_SIZE);
-	eiter->a.max_frame_size = cpu_to_be32(le16_to_cpu(IS_FWI2_CAPABLE(ha) ?
-		icb24->frame_payload_size : ha->init_cb->frame_payload_size));
+	eiter->a.max_frame_size = cpu_to_be32(ha->frame_payload_size);
 	alen = sizeof(eiter->a.max_frame_size);
 	alen += FDMI_ATTR_TYPELEN(eiter);
 	eiter->len = cpu_to_be16(alen);
@@ -2892,7 +2889,8 @@
 	qla24xx_handle_gpsc_event(vha, &ea);
 
 done:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_async_gpsc(scsi_qla_host_t *vha, fc_port_t *fcport)
@@ -2904,6 +2902,7 @@
 	if (!vha->flags.online || (fcport->flags & FCF_ASYNC_SENT))
 		return rval;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
@@ -2912,8 +2911,8 @@
 	sp->name = "gpsc";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
-
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla24xx_async_gpsc_sp_done);
 
 	/* CT_IU preamble  */
 	ct_req = qla24xx_prep_ct_fm_req(fcport->ct_desc.ct_sns, GPSC_CMD,
@@ -2931,9 +2930,6 @@
 	sp->u.iocb_cmd.u.ctarg.rsp_size = GPSC_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = vha->mgmt_svr_loop_id;
 
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	sp->done = qla24xx_async_gpsc_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0x205e,
 	    "Async-%s %8phC hdl=%x loopid=%x portid=%02x%02x%02x.\n",
 	    sp->name, fcport->port_name, sp->handle,
@@ -2946,7 +2942,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
@@ -2995,7 +2992,8 @@
 		break;
 	}
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 void qla24xx_handle_gpnid_event(scsi_qla_host_t *vha, struct event_arg *ea)
@@ -3134,13 +3132,15 @@
 	if (res) {
 		if (res == QLA_FUNCTION_TIMEOUT) {
 			qla24xx_post_gpnid_work(sp->vha, &ea.id);
-			sp->free(sp);
+			/* ref: INIT */
+			kref_put(&sp->cmd_kref, qla2x00_sp_release);
 			return;
 		}
 	} else if (sp->gen1) {
 		/* There was another RSCN for this Nport ID */
 		qla24xx_post_gpnid_work(sp->vha, &ea.id);
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
 		return;
 	}
 
@@ -3161,7 +3161,8 @@
 				  sp->u.iocb_cmd.u.ctarg.rsp_dma);
 		sp->u.iocb_cmd.u.ctarg.rsp = NULL;
 
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
 		return;
 	}
 
@@ -3181,6 +3182,7 @@
 	if (!vha->flags.online)
 		goto done;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 	if (!sp)
 		goto done;
@@ -3189,14 +3191,16 @@
 	sp->name = "gpnid";
 	sp->u.iocb_cmd.u.ctarg.id = *id;
 	sp->gen1 = 0;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_gpnid_sp_done);
 
 	spin_lock_irqsave(&vha->hw->tgt.sess_lock, flags);
 	list_for_each_entry(tsp, &vha->gpnid_list, elem) {
 		if (tsp->u.iocb_cmd.u.ctarg.id.b24 == id->b24) {
 			tsp->gen1++;
 			spin_unlock_irqrestore(&vha->hw->tgt.sess_lock, flags);
-			sp->free(sp);
+			/* ref: INIT */
+			kref_put(&sp->cmd_kref, qla2x00_sp_release);
 			goto done;
 		}
 	}
@@ -3237,9 +3241,6 @@
 	sp->u.iocb_cmd.u.ctarg.rsp_size = GPN_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	sp->done = qla2x00_async_gpnid_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0x2067,
 	    "Async-%s hdl=%x ID %3phC.\n", sp->name,
 	    sp->handle, &ct_req->req.port_id.port_id);
@@ -3269,25 +3270,18 @@
 			sp->u.iocb_cmd.u.ctarg.rsp_dma);
 		sp->u.iocb_cmd.u.ctarg.rsp = NULL;
 	}
-
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
 
-void qla24xx_handle_gffid_event(scsi_qla_host_t *vha, struct event_arg *ea)
-{
-	fc_port_t *fcport = ea->fcport;
-
-	qla24xx_post_gnl_work(vha, fcport);
-}
 
 void qla24xx_async_gffid_sp_done(srb_t *sp, int res)
 {
 	struct scsi_qla_host *vha = sp->vha;
 	fc_port_t *fcport = sp->fcport;
 	struct ct_sns_rsp *ct_rsp;
-	struct event_arg ea;
 	uint8_t fc4_scsi_feat;
 	uint8_t fc4_nvme_feat;
 
@@ -3295,10 +3289,10 @@
 	       "Async done-%s res %x ID %x. %8phC\n",
 	       sp->name, res, fcport->d_id.b24, fcport->port_name);
 
-	fcport->flags &= ~FCF_ASYNC_SENT;
-	ct_rsp = &fcport->ct_desc.ct_sns->p.rsp;
+	ct_rsp = sp->u.iocb_cmd.u.ctarg.rsp;
 	fc4_scsi_feat = ct_rsp->rsp.gff_id.fc4_features[GFF_FCP_SCSI_OFFSET];
 	fc4_nvme_feat = ct_rsp->rsp.gff_id.fc4_features[GFF_NVME_OFFSET];
+	sp->rc = res;
 
 	/*
 	 * FC-GS-7, 5.2.3.12 FC-4 Features - format
@@ -3319,68 +3313,129 @@
 		}
 	}
 
-	memset(&ea, 0, sizeof(ea));
-	ea.sp = sp;
-	ea.fcport = sp->fcport;
-	ea.rc = res;
+	if (sp->flags & SRB_WAKEUP_ON_COMP) {
+		complete(sp->comp);
+	} else  {
+		if (sp->u.iocb_cmd.u.ctarg.req) {
+			dma_free_coherent(&vha->hw->pdev->dev,
+				sp->u.iocb_cmd.u.ctarg.req_allocated_size,
+				sp->u.iocb_cmd.u.ctarg.req,
+				sp->u.iocb_cmd.u.ctarg.req_dma);
+			sp->u.iocb_cmd.u.ctarg.req = NULL;
+		}
 
-	qla24xx_handle_gffid_event(vha, &ea);
-	sp->free(sp);
+		if (sp->u.iocb_cmd.u.ctarg.rsp) {
+			dma_free_coherent(&vha->hw->pdev->dev,
+				sp->u.iocb_cmd.u.ctarg.rsp_allocated_size,
+				sp->u.iocb_cmd.u.ctarg.rsp,
+				sp->u.iocb_cmd.u.ctarg.rsp_dma);
+			sp->u.iocb_cmd.u.ctarg.rsp = NULL;
+		}
+
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
+		/* we should not be here */
+		dump_stack();
+	}
 }
 
 /* Get FC4 Feature with Nport ID. */
-int qla24xx_async_gffid(scsi_qla_host_t *vha, fc_port_t *fcport)
+int qla24xx_async_gffid(scsi_qla_host_t *vha, fc_port_t *fcport, bool wait)
 {
 	int rval = QLA_FUNCTION_FAILED;
 	struct ct_sns_req       *ct_req;
 	srb_t *sp;
+	DECLARE_COMPLETION_ONSTACK(comp);
 
-	if (!vha->flags.online || (fcport->flags & FCF_ASYNC_SENT))
+	/* this routine does not have handling for no wait */
+	if (!vha->flags.online || !wait)
 		return rval;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		return rval;
 
-	fcport->flags |= FCF_ASYNC_SENT;
 	sp->type = SRB_CT_PTHRU_CMD;
 	sp->name = "gffid";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla24xx_async_gffid_sp_done);
+	sp->comp = &comp;
+	sp->u.iocb_cmd.timeout = qla2x00_els_dcmd2_iocb_timeout;
+
+	if (wait)
+		sp->flags = SRB_WAKEUP_ON_COMP;
 
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	sp->u.iocb_cmd.u.ctarg.req_allocated_size = sizeof(struct ct_sns_pkt);
+	sp->u.iocb_cmd.u.ctarg.req = dma_alloc_coherent(&vha->hw->pdev->dev,
+				sp->u.iocb_cmd.u.ctarg.req_allocated_size,
+				&sp->u.iocb_cmd.u.ctarg.req_dma,
+	    GFP_KERNEL);
+	if (!sp->u.iocb_cmd.u.ctarg.req) {
+		ql_log(ql_log_warn, vha, 0xd041,
+		       "%s: Failed to allocate ct_sns request.\n",
+		       __func__);
+		goto done_free_sp;
+	}
+
+	sp->u.iocb_cmd.u.ctarg.rsp_allocated_size = sizeof(struct ct_sns_pkt);
+	sp->u.iocb_cmd.u.ctarg.rsp = dma_alloc_coherent(&vha->hw->pdev->dev,
+				sp->u.iocb_cmd.u.ctarg.rsp_allocated_size,
+				&sp->u.iocb_cmd.u.ctarg.rsp_dma,
+	    GFP_KERNEL);
+	if (!sp->u.iocb_cmd.u.ctarg.rsp) {
+		ql_log(ql_log_warn, vha, 0xd041,
+		       "%s: Failed to allocate ct_sns response.\n",
+		       __func__);
+		goto done_free_sp;
+	}
 
 	/* CT_IU preamble  */
-	ct_req = qla2x00_prep_ct_req(fcport->ct_desc.ct_sns, GFF_ID_CMD,
-	    GFF_ID_RSP_SIZE);
+	ct_req = qla2x00_prep_ct_req(sp->u.iocb_cmd.u.ctarg.req, GFF_ID_CMD, GFF_ID_RSP_SIZE);
 
 	ct_req->req.gff_id.port_id[0] = fcport->d_id.b.domain;
 	ct_req->req.gff_id.port_id[1] = fcport->d_id.b.area;
 	ct_req->req.gff_id.port_id[2] = fcport->d_id.b.al_pa;
 
-	sp->u.iocb_cmd.u.ctarg.req = fcport->ct_desc.ct_sns;
-	sp->u.iocb_cmd.u.ctarg.req_dma = fcport->ct_desc.ct_sns_dma;
-	sp->u.iocb_cmd.u.ctarg.rsp = fcport->ct_desc.ct_sns;
-	sp->u.iocb_cmd.u.ctarg.rsp_dma = fcport->ct_desc.ct_sns_dma;
 	sp->u.iocb_cmd.u.ctarg.req_size = GFF_ID_REQ_SIZE;
 	sp->u.iocb_cmd.u.ctarg.rsp_size = GFF_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->done = qla24xx_async_gffid_sp_done;
-
-	ql_dbg(ql_dbg_disc, vha, 0x2132,
-	    "Async-%s hdl=%x  %8phC.\n", sp->name,
-	    sp->handle, fcport->port_name);
-
 	rval = qla2x00_start_sp(sp);
-	if (rval != QLA_SUCCESS)
+
+	if (rval != QLA_SUCCESS) {
+		rval = QLA_FUNCTION_FAILED;
 		goto done_free_sp;
+	} else {
+		ql_dbg(ql_dbg_disc, vha, 0x3074,
+		       "Async-%s hdl=%x portid %06x\n",
+		       sp->name, sp->handle, fcport->d_id.b24);
+	}
+
+	wait_for_completion(sp->comp);
+	rval = sp->rc;
 
-	return rval;
 done_free_sp:
-	sp->free(sp);
-	fcport->flags &= ~FCF_ASYNC_SENT;
+	if (sp->u.iocb_cmd.u.ctarg.req) {
+		dma_free_coherent(&vha->hw->pdev->dev,
+				  sp->u.iocb_cmd.u.ctarg.req_allocated_size,
+				  sp->u.iocb_cmd.u.ctarg.req,
+				  sp->u.iocb_cmd.u.ctarg.req_dma);
+		sp->u.iocb_cmd.u.ctarg.req = NULL;
+	}
+
+	if (sp->u.iocb_cmd.u.ctarg.rsp) {
+		dma_free_coherent(&vha->hw->pdev->dev,
+				  sp->u.iocb_cmd.u.ctarg.rsp_allocated_size,
+				  sp->u.iocb_cmd.u.ctarg.rsp,
+				  sp->u.iocb_cmd.u.ctarg.rsp_dma);
+		sp->u.iocb_cmd.u.ctarg.rsp = NULL;
+	}
+
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	return rval;
 }
 
@@ -3409,6 +3464,29 @@
 	return rc;
 }
 
+static bool qla_ok_to_clear_rscn(scsi_qla_host_t *vha, fc_port_t *fcport)
+{
+	u32 rscn_gen;
+
+	rscn_gen = atomic_read(&vha->rscn_gen);
+	ql_dbg(ql_dbg_disc + ql_dbg_verbose, vha, 0x2017,
+	    "%s %d %8phC rscn_gen %x start %x end %x current %x\n",
+	    __func__, __LINE__, fcport->port_name, fcport->rscn_gen,
+	    vha->scan.rscn_gen_start, vha->scan.rscn_gen_end, rscn_gen);
+
+	if (val_is_in_range(fcport->rscn_gen, vha->scan.rscn_gen_start,
+	    vha->scan.rscn_gen_end))
+		/* rscn came in before fabric scan */
+		return true;
+
+	if (val_is_in_range(fcport->rscn_gen, vha->scan.rscn_gen_end, rscn_gen))
+		/* rscn came in after fabric scan */
+		return false;
+
+	/* rare: fcport's scan_needed + rscn_gen must be stale */
+	return true;
+}
+
 void qla24xx_async_gnnft_done(scsi_qla_host_t *vha, srb_t *sp)
 {
 	fc_port_t *fcport;
@@ -3522,10 +3600,10 @@
 				   (fcport->scan_needed &&
 				    fcport->port_type != FCT_INITIATOR &&
 				    fcport->port_type != FCT_NVME_INITIATOR)) {
+				fcport->scan_needed = 0;
 				qlt_schedule_sess_for_deletion(fcport);
 			}
 			fcport->d_id.b24 = rp->id.b24;
-			fcport->scan_needed = 0;
 			break;
 		}
 
@@ -3566,14 +3644,16 @@
 				do_delete = true;
 			}
 
-			fcport->scan_needed = 0;
+			if (qla_ok_to_clear_rscn(vha, fcport))
+				fcport->scan_needed = 0;
+
 			if (((qla_dual_mode_enabled(vha) ||
 			      qla_ini_mode_enabled(vha)) &&
 			    atomic_read(&fcport->state) == FCS_ONLINE) ||
 				do_delete) {
 				if (fcport->loop_id != FC_NO_LOOP_ID) {
 					if (fcport->flags & FCF_FCP2_DEVICE)
-						fcport->logout_on_delete = 0;
+						continue;
 
 					ql_log(ql_log_warn, vha, 0x20f0,
 					       "%s %d %8phC post del sess\n",
@@ -3596,7 +3676,9 @@
 					    fcport->port_name, fcport->loop_id,
 					    fcport->login_retry);
 				}
-				fcport->scan_needed = 0;
+
+				if (qla_ok_to_clear_rscn(vha, fcport))
+					fcport->scan_needed = 0;
 				qla24xx_fcport_handle_login(vha, fcport);
 			}
 		}
@@ -3766,7 +3848,6 @@
 	    "Async done-%s res %x FC4Type %x\n",
 	    sp->name, res, sp->gen2);
 
-	del_timer(&sp->u.iocb_cmd.timer);
 	sp->rc = res;
 	if (res) {
 		unsigned long flags;
@@ -3891,9 +3972,8 @@
 	sp->name = "gnnft";
 	sp->gen1 = vha->hw->base_qpair->chip_reset;
 	sp->gen2 = fc4_type;
-
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_gpnft_gnnft_sp_done);
 
 	memset(sp->u.iocb_cmd.u.ctarg.rsp, 0, sp->u.iocb_cmd.u.ctarg.rsp_size);
 	memset(sp->u.iocb_cmd.u.ctarg.req, 0, sp->u.iocb_cmd.u.ctarg.req_size);
@@ -3909,8 +3989,6 @@
 	sp->u.iocb_cmd.u.ctarg.req_size = GNN_FT_REQ_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->done = qla2x00_async_gpnft_gnnft_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s hdl=%x FC4Type %x.\n", sp->name,
 	    sp->handle, ct_req->req.gpn_ft.port_type);
@@ -3937,8 +4015,8 @@
 		    sp->u.iocb_cmd.u.ctarg.rsp_dma);
 		sp->u.iocb_cmd.u.ctarg.rsp = NULL;
 	}
-
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 
 	spin_lock_irqsave(&vha->work_lock, flags);
 	vha->scan.scan_flags &= ~SF_SCANNING;
@@ -3990,9 +4068,12 @@
 		ql_dbg(ql_dbg_disc + ql_dbg_verbose, vha, 0xffff,
 		    "%s: Performing FCP Scan\n", __func__);
 
-		if (sp)
-			sp->free(sp); /* should not happen */
+		if (sp) {
+			/* ref: INIT */
+			kref_put(&sp->cmd_kref, qla2x00_sp_release);
+		}
 
+		/* ref: INIT */
 		sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 		if (!sp) {
 			spin_lock_irqsave(&vha->work_lock, flags);
@@ -4037,6 +4118,7 @@
 			    sp->u.iocb_cmd.u.ctarg.req,
 			    sp->u.iocb_cmd.u.ctarg.req_dma);
 			sp->u.iocb_cmd.u.ctarg.req = NULL;
+			/* ref: INIT */
 			qla2x00_rel_sp(sp);
 			return rval;
 		}
@@ -4056,9 +4138,8 @@
 	sp->name = "gpnft";
 	sp->gen1 = vha->hw->base_qpair->chip_reset;
 	sp->gen2 = fc4_type;
-
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_gpnft_gnnft_sp_done);
 
 	rspsz = sp->u.iocb_cmd.u.ctarg.rsp_size;
 	memset(sp->u.iocb_cmd.u.ctarg.rsp, 0, sp->u.iocb_cmd.u.ctarg.rsp_size);
@@ -4073,8 +4154,6 @@
 
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->done = qla2x00_async_gpnft_gnnft_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s hdl=%x FC4Type %x.\n", sp->name,
 	    sp->handle, ct_req->req.gpn_ft.port_type);
@@ -4102,7 +4181,8 @@
 		sp->u.iocb_cmd.u.ctarg.rsp = NULL;
 	}
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 
 	spin_lock_irqsave(&vha->work_lock, flags);
 	vha->scan.scan_flags &= ~SF_SCANNING;
@@ -4166,7 +4246,8 @@
 
 	qla24xx_handle_gnnid_event(vha, &ea);
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_async_gnnid(scsi_qla_host_t *vha, fc_port_t *fcport)
@@ -4179,6 +4260,7 @@
 		return rval;
 
 	qla2x00_set_fcport_disc_state(fcport, DSC_GNN_ID);
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_ATOMIC);
 	if (!sp)
 		goto done;
@@ -4188,9 +4270,8 @@
 	sp->name = "gnnid";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
-
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_gnnid_sp_done);
 
 	/* CT_IU preamble  */
 	ct_req = qla2x00_prep_ct_req(fcport->ct_desc.ct_sns, GNN_ID_CMD,
@@ -4209,8 +4290,6 @@
 	sp->u.iocb_cmd.u.ctarg.rsp_size = GNN_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->done = qla2x00_async_gnnid_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s - %8phC hdl=%x loopid=%x portid %06x.\n",
 	    sp->name, fcport->port_name,
@@ -4222,7 +4301,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	fcport->flags &= ~FCF_ASYNC_SENT;
 done:
 	return rval;
@@ -4296,7 +4376,8 @@
 
 	qla24xx_handle_gfpnid_event(vha, &ea);
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_async_gfpnid(scsi_qla_host_t *vha, fc_port_t *fcport)
@@ -4308,6 +4389,7 @@
 	if (!vha->flags.online || (fcport->flags & FCF_ASYNC_SENT))
 		return rval;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_ATOMIC);
 	if (!sp)
 		goto done;
@@ -4316,9 +4398,8 @@
 	sp->name = "gfpnid";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
-
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_gfpnid_sp_done);
 
 	/* CT_IU preamble  */
 	ct_req = qla2x00_prep_ct_req(fcport->ct_desc.ct_sns, GFPN_ID_CMD,
@@ -4337,8 +4418,6 @@
 	sp->u.iocb_cmd.u.ctarg.rsp_size = GFPN_ID_RSP_SIZE;
 	sp->u.iocb_cmd.u.ctarg.nport_handle = NPH_SNS;
 
-	sp->done = qla2x00_async_gfpnid_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0xffff,
 	    "Async-%s - %8phC hdl=%x loopid=%x portid %06x.\n",
 	    sp->name, fcport->port_name,
@@ -4351,7 +4430,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_init.c
@@ -47,10 +47,20 @@
 {
 	srb_t *sp = from_timer(sp, t, u.iocb_cmd.timer);
 	struct srb_iocb *iocb;
+	scsi_qla_host_t *vha = sp->vha;
 
 	WARN_ON(irqs_disabled());
 	iocb = &sp->u.iocb_cmd;
 	iocb->timeout(sp);
+
+	/* ref: TMR */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
+
+	if (vha && qla2x00_isp_reg_stat(vha->hw)) {
+		ql_log(ql_log_info, vha, 0x9008,
+		    "PCI/Register disconnect.\n");
+		qla_pci_set_eeh_busy(vha);
+	}
 }
 
 void qla2x00_sp_free(srb_t *sp)
@@ -100,6 +110,7 @@
 	struct qla_qpair *qpair = sp->qpair;
 	u32 handle;
 	unsigned long flags;
+	int sp_found = 0, cmdsp_found = 0;
 
 	if (sp->cmd_sp)
 		ql_dbg(ql_dbg_async, sp->vha, 0x507c,
@@ -114,22 +125,34 @@
 	spin_lock_irqsave(qpair->qp_lock_ptr, flags);
 	for (handle = 1; handle < qpair->req->num_outstanding_cmds; handle++) {
 		if (sp->cmd_sp && (qpair->req->outstanding_cmds[handle] ==
-		    sp->cmd_sp))
+		    sp->cmd_sp)) {
 			qpair->req->outstanding_cmds[handle] = NULL;
+			cmdsp_found = 1;
+			qla_put_fw_resources(qpair, &sp->cmd_sp->iores);
+		}
 
 		/* removing the abort */
 		if (qpair->req->outstanding_cmds[handle] == sp) {
 			qpair->req->outstanding_cmds[handle] = NULL;
+			sp_found = 1;
+			qla_put_fw_resources(qpair, &sp->iores);
 			break;
 		}
 	}
 	spin_unlock_irqrestore(qpair->qp_lock_ptr, flags);
 
-	if (sp->cmd_sp)
+	if (cmdsp_found && sp->cmd_sp) {
+		/*
+		 * This done function should take care of
+		 * original command ref: INIT
+		 */
 		sp->cmd_sp->done(sp->cmd_sp, QLA_OS_TIMER_EXPIRED);
+	}
 
-	abt->u.abt.comp_status = cpu_to_le16(CS_TIMEOUT);
-	sp->done(sp, QLA_OS_TIMER_EXPIRED);
+	if (sp_found) {
+		abt->u.abt.comp_status = cpu_to_le16(CS_TIMEOUT);
+		sp->done(sp, QLA_OS_TIMER_EXPIRED);
+	}
 }
 
 static void qla24xx_abort_sp_done(srb_t *sp, int res)
@@ -140,11 +163,11 @@
 	if (orig_sp)
 		qla_wait_nvme_release_cmd_kref(orig_sp);
 
-	del_timer(&sp->u.iocb_cmd.timer);
 	if (sp->flags & SRB_WAKEUP_ON_COMP)
 		complete(&abt->u.abt.comp);
 	else
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_async_abort_cmd(srb_t *cmd_sp, bool wait)
@@ -154,11 +177,13 @@
 	srb_t *sp;
 	int rval = QLA_FUNCTION_FAILED;
 
+	/* ref: INIT for ABTS command */
 	sp = qla2xxx_get_qpair_sp(cmd_sp->vha, cmd_sp->qpair, cmd_sp->fcport,
 				  GFP_ATOMIC);
 	if (!sp)
 		return QLA_MEMORY_ALLOC_FAILED;
 
+	qla_vha_mark_busy(vha);
 	abt_iocb = &sp->u.iocb_cmd;
 	sp->type = SRB_ABT_CMD;
 	sp->name = "abort";
@@ -167,23 +192,22 @@
 	if (wait)
 		sp->flags = SRB_WAKEUP_ON_COMP;
 
-	abt_iocb->timeout = qla24xx_abort_iocb_timeout;
 	init_completion(&abt_iocb->u.abt.comp);
 	/* FW can send 2 x ABTS's timeout/20s */
-	qla2x00_init_timer(sp, 42);
+	qla2x00_init_async_sp(sp, 42, qla24xx_abort_sp_done);
+	sp->u.iocb_cmd.timeout = qla24xx_abort_iocb_timeout;
 
 	abt_iocb->u.abt.cmd_hndl = cmd_sp->handle;
 	abt_iocb->u.abt.req_que_no = cpu_to_le16(cmd_sp->qpair->req->id);
 
-	sp->done = qla24xx_abort_sp_done;
-
 	ql_dbg(ql_dbg_async, vha, 0x507c,
 	       "Abort command issued - hdl=%x, type=%x\n", cmd_sp->handle,
 	       cmd_sp->type);
 
 	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS) {
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
 		return rval;
 	}
 
@@ -191,7 +215,8 @@
 		wait_for_completion(&abt_iocb->u.abt.comp);
 		rval = abt_iocb->u.abt.comp_status == CS_COMPLETE ?
 			QLA_SUCCESS : QLA_ERR_FROM_FW;
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	}
 
 	return rval;
@@ -286,10 +311,13 @@
 		ea.iop[0] = lio->u.logio.iop[0];
 		ea.iop[1] = lio->u.logio.iop[1];
 		ea.sp = sp;
+		if (res)
+			ea.data[0] = MBS_COMMAND_ERROR;
 		qla24xx_handle_plogi_done_event(vha, &ea);
 	}
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int
@@ -308,6 +336,7 @@
 		return rval;
 	}
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
@@ -320,17 +349,15 @@
 	sp->name = "login";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_login_sp_done);
 
 	lio = &sp->u.iocb_cmd;
-	lio->timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
-
-	sp->done = qla2x00_async_login_sp_done;
 	if (N2N_TOPO(fcport->vha->hw) && fcport_is_bigger(fcport)) {
 		lio->u.logio.flags |= SRB_LOGIN_PRLI_ONLY;
 	} else {
 		if (vha->hw->flags.edif_enabled &&
-		    vha->e_dbell.db_flags & EDB_ACTIVE) {
+		    DBELL_ACTIVE(vha)) {
 			lio->u.logio.flags |=
 				(SRB_LOGIN_FCSP | SRB_LOGIN_SKIP_PRLI);
 			ql_dbg(ql_dbg_disc, vha, 0x2072,
@@ -359,7 +386,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	fcport->flags &= ~FCF_ASYNC_SENT;
 done:
 	fcport->flags &= ~FCF_ASYNC_ACTIVE;
@@ -371,29 +399,26 @@
 	sp->fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
 	sp->fcport->login_gen++;
 	qlt_logo_completion_handler(sp->fcport, sp->u.iocb_cmd.u.logio.data[0]);
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int
 qla2x00_async_logout(struct scsi_qla_host *vha, fc_port_t *fcport)
 {
 	srb_t *sp;
-	struct srb_iocb *lio;
 	int rval = QLA_FUNCTION_FAILED;
 
 	fcport->flags |= FCF_ASYNC_SENT;
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_LOGOUT_CMD;
 	sp->name = "logout";
-
-	lio = &sp->u.iocb_cmd;
-	lio->timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
-
-	sp->done = qla2x00_async_logout_sp_done;
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_logout_sp_done),
 
 	ql_dbg(ql_dbg_disc, vha, 0x2070,
 	    "Async-logout - hdl=%x loop-id=%x portid=%02x%02x%02x %8phC explicit %d.\n",
@@ -407,7 +432,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
 	return rval;
@@ -433,29 +459,26 @@
 	if (!test_bit(UNLOADING, &vha->dpc_flags))
 		qla2x00_post_async_prlo_done_work(sp->fcport->vha, sp->fcport,
 		    lio->u.logio.data);
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int
 qla2x00_async_prlo(struct scsi_qla_host *vha, fc_port_t *fcport)
 {
 	srb_t *sp;
-	struct srb_iocb *lio;
 	int rval;
 
 	rval = QLA_FUNCTION_FAILED;
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_PRLO_CMD;
 	sp->name = "prlo";
-
-	lio = &sp->u.iocb_cmd;
-	lio->timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
-
-	sp->done = qla2x00_async_prlo_sp_done;
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_prlo_sp_done);
 
 	ql_dbg(ql_dbg_disc, vha, 0x2070,
 	    "Async-prlo - hdl=%x loop-id=%x portid=%02x%02x%02x.\n",
@@ -469,7 +492,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	fcport->flags &= ~FCF_ASYNC_ACTIVE;
 	return rval;
@@ -479,6 +503,7 @@
 void qla24xx_handle_adisc_event(scsi_qla_host_t *vha, struct event_arg *ea)
 {
 	struct fc_port *fcport = ea->fcport;
+	unsigned long flags;
 
 	ql_dbg(ql_dbg_disc, vha, 0x20d2,
 	    "%s %8phC DS %d LS %d rc %d login %d|%d rscn %d|%d lid %d\n",
@@ -493,9 +518,15 @@
 		ql_dbg(ql_dbg_disc, vha, 0x2066,
 		    "%s %8phC: adisc fail: post delete\n",
 		    __func__, ea->fcport->port_name);
+
+		spin_lock_irqsave(&vha->work_lock, flags);
 		/* deleted = 0 & logout_on_delete = force fw cleanup */
-		fcport->deleted = 0;
+		if (fcport->deleted == QLA_SESS_DELETED)
+			fcport->deleted = 0;
+
 		fcport->logout_on_delete = 1;
+		spin_unlock_irqrestore(&vha->work_lock, flags);
+
 		qlt_schedule_sess_for_deletion(ea->fcport);
 		return;
 	}
@@ -552,10 +583,12 @@
 	ea.iop[1] = lio->u.logio.iop[1];
 	ea.fcport = sp->fcport;
 	ea.sp = sp;
+	if (res)
+		ea.data[0] = MBS_COMMAND_ERROR;
 
 	qla24xx_handle_adisc_event(vha, &ea);
-
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int
@@ -566,26 +599,34 @@
 	struct srb_iocb *lio;
 	int rval = QLA_FUNCTION_FAILED;
 
+	if (IS_SESSION_DELETED(fcport)) {
+		ql_log(ql_log_warn, vha, 0xffff,
+		       "%s: %8phC is being delete - not sending command.\n",
+		       __func__, fcport->port_name);
+		fcport->flags &= ~FCF_ASYNC_ACTIVE;
+		return rval;
+	}
+
 	if (!vha->flags.online || (fcport->flags & FCF_ASYNC_SENT))
 		return rval;
 
 	fcport->flags |= FCF_ASYNC_SENT;
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_ADISC_CMD;
 	sp->name = "adisc";
-
-	lio = &sp->u.iocb_cmd;
-	lio->timeout = qla2x00_async_iocb_timeout;
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_adisc_sp_done);
 
-	sp->done = qla2x00_async_adisc_sp_done;
-	if (data[1] & QLA_LOGIO_LOGIN_RETRIED)
+	if (data[1] & QLA_LOGIO_LOGIN_RETRIED) {
+		lio = &sp->u.iocb_cmd;
 		lio->u.logio.flags |= SRB_LOGIN_RETRIED;
+	}
 
 	ql_dbg(ql_dbg_disc, vha, 0x206f,
 	    "Async-adisc - hdl=%x loopid=%x portid=%06x %8phC.\n",
@@ -598,7 +639,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
 	qla2x00_post_async_adisc_work(vha, fcport, data);
@@ -862,7 +904,7 @@
 				break;
 			case DSC_LS_PLOGI_COMP:
 				if (vha->hw->flags.edif_enabled &&
-				    vha->e_dbell.db_flags & EDB_ACTIVE) {
+				    DBELL_ACTIVE(vha)) {
 					/* check to see if App support secure or not */
 					qla24xx_post_gpdb_work(vha, fcport, 0);
 					break;
@@ -964,6 +1006,9 @@
 				set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
 			}
 			break;
+		case ISP_CFG_NL:
+			qla24xx_fcport_handle_login(vha, fcport);
+			break;
 		default:
 			break;
 		}
@@ -987,8 +1032,6 @@
 	    sp->name, res, sp->u.iocb_cmd.u.mbx.in_mb[1],
 	    sp->u.iocb_cmd.u.mbx.in_mb[2]);
 
-	if (res == QLA_FUNCTION_TIMEOUT)
-		return;
 
 	sp->fcport->flags &= ~(FCF_ASYNC_SENT|FCF_ASYNC_ACTIVE);
 	memset(&ea, 0, sizeof(ea));
@@ -1026,8 +1069,8 @@
 	spin_unlock_irqrestore(&vha->hw->tgt.sess_lock, flags);
 
 	list_for_each_entry_safe(fcport, tf, &h, gnl_entry) {
-		list_del_init(&fcport->gnl_entry);
 		spin_lock_irqsave(&vha->hw->tgt.sess_lock, flags);
+		list_del_init(&fcport->gnl_entry);
 		fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
 		spin_unlock_irqrestore(&vha->hw->tgt.sess_lock, flags);
 		ea.fcport = fcport;
@@ -1081,19 +1124,19 @@
 	}
 	spin_unlock_irqrestore(&vha->hw->tgt.sess_lock, flags);
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_async_gnl(struct scsi_qla_host *vha, fc_port_t *fcport)
 {
 	srb_t *sp;
-	struct srb_iocb *mbx;
 	int rval = QLA_FUNCTION_FAILED;
 	unsigned long flags;
 	u16 *mb;
 
 	if (!vha->flags.online || (fcport->flags & FCF_ASYNC_SENT))
-		return rval;
+		goto done;
 
 	ql_dbg(ql_dbg_disc, vha, 0x20d9,
 	    "Async-gnlist WWPN %8phC \n", fcport->port_name);
@@ -1112,6 +1155,7 @@
 	vha->gnl.sent = 1;
 	spin_unlock_irqrestore(&vha->hw->tgt.sess_lock, flags);
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
@@ -1120,10 +1164,8 @@
 	sp->name = "gnlist";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
-
-	mbx = &sp->u.iocb_cmd;
-	mbx->timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha)+2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla24xx_async_gnl_sp_done);
 
 	mb = sp->u.iocb_cmd.u.mbx.out_mb;
 	mb[0] = MBC_PORT_NODE_NAME_LIST;
@@ -1135,8 +1177,6 @@
 	mb[8] = vha->gnl.size;
 	mb[9] = vha->vp_idx;
 
-	sp->done = qla24xx_async_gnl_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0x20da,
 	    "Async-%s - OUT WWPN %8phC hndl %x\n",
 	    sp->name, fcport->port_name, sp->handle);
@@ -1148,9 +1188,15 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/*
+	 * use qla24xx_async_gnl_sp_done to purge all pending gnl request.
+	 * kref_put is call behind the scene.
+	 */
+	sp->u.iocb_cmd.u.mbx.in_mb[0] = MBS_COMMAND_ERROR;
+	qla24xx_async_gnl_sp_done(sp, QLA_COMMAND_ERROR);
+	fcport->flags &= ~(FCF_ASYNC_SENT);
 done:
-	fcport->flags &= ~(FCF_ASYNC_ACTIVE | FCF_ASYNC_SENT);
+	fcport->flags &= ~(FCF_ASYNC_ACTIVE);
 	return rval;
 }
 
@@ -1194,7 +1240,7 @@
 	dma_pool_free(ha->s_dma_pool, sp->u.iocb_cmd.u.mbx.in,
 		sp->u.iocb_cmd.u.mbx.in_dma);
 
-	sp->free(sp);
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_post_prli_work(struct scsi_qla_host *vha, fc_port_t *fcport)
@@ -1235,11 +1281,13 @@
 		ea.sp = sp;
 		if (res == QLA_OS_TIMER_EXPIRED)
 			ea.data[0] = QLA_OS_TIMER_EXPIRED;
+		else if (res)
+			ea.data[0] = MBS_COMMAND_ERROR;
 
 		qla24xx_handle_prli_done_event(vha, &ea);
 	}
 
-	sp->free(sp);
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int
@@ -1272,12 +1320,10 @@
 
 	sp->type = SRB_PRLI_CMD;
 	sp->name = "prli";
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_prli_sp_done);
 
 	lio = &sp->u.iocb_cmd;
-	lio->timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
-
-	sp->done = qla2x00_async_prli_sp_done;
 	lio->u.logio.flags = 0;
 
 	if (NVME_TARGET(vha->hw, fcport))
@@ -1299,7 +1345,8 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	fcport->flags &= ~FCF_ASYNC_SENT;
 	return rval;
 }
@@ -1328,14 +1375,21 @@
 	struct port_database_24xx *pd;
 	struct qla_hw_data *ha = vha->hw;
 
-	if (!vha->flags.online || (fcport->flags & FCF_ASYNC_SENT) ||
-	    fcport->loop_id == FC_NO_LOOP_ID) {
+	if (IS_SESSION_DELETED(fcport)) {
 		ql_log(ql_log_warn, vha, 0xffff,
-		    "%s: %8phC - not sending command.\n",
-		    __func__, fcport->port_name);
+		       "%s: %8phC is being delete - not sending command.\n",
+		       __func__, fcport->port_name);
+		fcport->flags &= ~FCF_ASYNC_ACTIVE;
 		return rval;
 	}
 
+	if (!vha->flags.online || fcport->flags & FCF_ASYNC_SENT) {
+		ql_log(ql_log_warn, vha, 0xffff,
+		    "%s: %8phC online %d flags %x - not sending command.\n",
+		    __func__, fcport->port_name, vha->flags.online, fcport->flags);
+		goto done;
+	}
+
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
@@ -1347,10 +1401,8 @@
 	sp->name = "gpdb";
 	sp->gen1 = fcport->rscn_gen;
 	sp->gen2 = fcport->login_gen;
-
-	mbx = &sp->u.iocb_cmd;
-	mbx->timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla24xx_async_gpdb_sp_done);
 
 	pd = dma_pool_zalloc(ha->s_dma_pool, GFP_KERNEL, &pd_dma);
 	if (pd == NULL) {
@@ -1369,11 +1421,10 @@
 	mb[9] = vha->vp_idx;
 	mb[10] = opt;
 
-	mbx->u.mbx.in = pd;
+	mbx = &sp->u.iocb_cmd;
+	mbx->u.mbx.in = (void *)pd;
 	mbx->u.mbx.in_dma = pd_dma;
 
-	sp->done = qla24xx_async_gpdb_sp_done;
-
 	ql_dbg(ql_dbg_disc, vha, 0x20dc,
 	    "Async-%s %8phC hndl %x opt %x\n",
 	    sp->name, fcport->port_name, sp->handle, opt);
@@ -1387,7 +1438,7 @@
 	if (pd)
 		dma_pool_free(ha->s_dma_pool, pd, pd_dma);
 
-	sp->free(sp);
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	fcport->flags &= ~FCF_ASYNC_SENT;
 done:
 	fcport->flags &= ~FCF_ASYNC_ACTIVE;
@@ -1402,7 +1453,6 @@
 
 	spin_lock_irqsave(&vha->hw->tgt.sess_lock, flags);
 	ea->fcport->login_gen++;
-	ea->fcport->deleted = 0;
 	ea->fcport->logout_on_delete = 1;
 
 	if (!ea->fcport->login_succ && !IS_SW_RESV_ADDR(ea->fcport->d_id)) {
@@ -1454,7 +1504,7 @@
 			qla2x00_post_aen_work(vha, FCH_EVT_PORT_ONLINE,
 			    fcport->d_id.b24);
 
-			if (vha->e_dbell.db_flags ==  EDB_ACTIVE) {
+			if (DBELL_ACTIVE(vha)) {
 				ql_dbg(ql_dbg_disc, vha, 0x20ef,
 				    "%s %d %8phC EDIF: post DB_AUTH: AUTH needed\n",
 				    __func__, __LINE__, fcport->port_name);
@@ -1559,6 +1609,11 @@
 	u8 login = 0;
 	int rc;
 
+	ql_dbg(ql_dbg_disc, vha, 0x307b,
+	    "%s %8phC DS %d LS %d lid %d retries=%d\n",
+	    __func__, fcport->port_name, fcport->disc_state,
+	    fcport->fw_login_state, fcport->loop_id, fcport->login_retry);
+
 	if (qla_tgt_mode_enabled(vha))
 		return;
 
@@ -1617,7 +1672,8 @@
 	    fcport->login_gen, fcport->loop_id, fcport->scan_state,
 	    fcport->fc4_type);
 
-	if (fcport->scan_state != QLA_FCPORT_FOUND)
+	if (fcport->scan_state != QLA_FCPORT_FOUND ||
+	    fcport->disc_state == DSC_DELETE_PEND)
 		return 0;
 
 	if ((fcport->loop_id != FC_NO_LOOP_ID) &&
@@ -1638,7 +1694,7 @@
 	if (vha->host->active_mode == MODE_TARGET && !N2N_TOPO(vha->hw))
 		return 0;
 
-	if (fcport->flags & FCF_ASYNC_SENT) {
+	if (fcport->flags & (FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE)) {
 		set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
 		return 0;
 	}
@@ -1735,8 +1791,16 @@
 		break;
 
 	case DSC_LOGIN_PEND:
-		if (fcport->fw_login_state == DSC_LS_PLOGI_COMP)
+		if (vha->hw->flags.edif_enabled)
+			break;
+
+		if (fcport->fw_login_state == DSC_LS_PLOGI_COMP) {
+			ql_dbg(ql_dbg_disc, vha, 0x2118,
+			       "%s %d %8phC post %s PRLI\n",
+			       __func__, __LINE__, fcport->port_name,
+			       NVME_TARGET(vha->hw, fcport) ? "NVME" : "FC");
 			qla24xx_post_prli_work(vha, fcport);
+		}
 		break;
 
 	case DSC_UPD_FCPORT:
@@ -1781,27 +1845,99 @@
 	return qla2x00_post_work(vha, e);
 }
 
+static void qla_rscn_gen_tick(scsi_qla_host_t *vha, u32 *ret_rscn_gen)
+{
+	*ret_rscn_gen = atomic_inc_return(&vha->rscn_gen);
+	/* memory barrier */
+	wmb();
+}
+
 void qla2x00_handle_rscn(scsi_qla_host_t *vha, struct event_arg *ea)
 {
 	fc_port_t *fcport;
 	unsigned long flags;
+	u32 rscn_gen;
 
-	fcport = qla2x00_find_fcport_by_nportid(vha, &ea->id, 1);
-	if (fcport) {
-		if (fcport->flags & FCF_FCP2_DEVICE) {
-			ql_dbg(ql_dbg_disc, vha, 0x2115,
-			       "Delaying session delete for FCP2 portid=%06x %8phC ",
-			       fcport->d_id.b24, fcport->port_name);
-			return;
+	switch (ea->id.b.rsvd_1) {
+	case RSCN_PORT_ADDR:
+		fcport = qla2x00_find_fcport_by_nportid(vha, &ea->id, 1);
+		if (fcport) {
+			if (fcport->flags & FCF_FCP2_DEVICE &&
+			    atomic_read(&fcport->state) == FCS_ONLINE) {
+				ql_dbg(ql_dbg_disc, vha, 0x2115,
+				       "Delaying session delete for FCP2 portid=%06x %8phC ",
+					fcport->d_id.b24, fcport->port_name);
+				return;
+			}
+
+			if (vha->hw->flags.edif_enabled && DBELL_ACTIVE(vha)) {
+				/*
+				 * On ipsec start by remote port, Target port
+				 * may use RSCN to trigger initiator to
+				 * relogin. If driver is already in the
+				 * process of a relogin, then ignore the RSCN
+				 * and allow the current relogin to continue.
+				 * This reduces thrashing of the connection.
+				 */
+				if (atomic_read(&fcport->state) == FCS_ONLINE) {
+					/*
+					 * If state = online, then set scan_needed=1 to do relogin.
+					 * Otherwise we're already in the middle of a relogin
+					 */
+					fcport->scan_needed = 1;
+					qla_rscn_gen_tick(vha, &fcport->rscn_gen);
+				}
+			} else {
+				fcport->scan_needed = 1;
+				qla_rscn_gen_tick(vha, &fcport->rscn_gen);
+			}
 		}
-		fcport->scan_needed = 1;
-		fcport->rscn_gen++;
+		break;
+	case RSCN_AREA_ADDR:
+		qla_rscn_gen_tick(vha, &rscn_gen);
+		list_for_each_entry(fcport, &vha->vp_fcports, list) {
+			if (fcport->flags & FCF_FCP2_DEVICE &&
+			    atomic_read(&fcport->state) == FCS_ONLINE)
+				continue;
+
+			if ((ea->id.b24 & 0xffff00) == (fcport->d_id.b24 & 0xffff00)) {
+				fcport->scan_needed = 1;
+				fcport->rscn_gen = rscn_gen;
+			}
+		}
+		break;
+	case RSCN_DOM_ADDR:
+		qla_rscn_gen_tick(vha, &rscn_gen);
+		list_for_each_entry(fcport, &vha->vp_fcports, list) {
+			if (fcport->flags & FCF_FCP2_DEVICE &&
+			    atomic_read(&fcport->state) == FCS_ONLINE)
+				continue;
+
+			if ((ea->id.b24 & 0xff0000) == (fcport->d_id.b24 & 0xff0000)) {
+				fcport->scan_needed = 1;
+				fcport->rscn_gen = rscn_gen;
+			}
+		}
+		break;
+	case RSCN_FAB_ADDR:
+	default:
+		qla_rscn_gen_tick(vha, &rscn_gen);
+		list_for_each_entry(fcport, &vha->vp_fcports, list) {
+			if (fcport->flags & FCF_FCP2_DEVICE &&
+			    atomic_read(&fcport->state) == FCS_ONLINE)
+				continue;
+
+			fcport->scan_needed = 1;
+			fcport->rscn_gen = rscn_gen;
+		}
+		break;
 	}
 
 	spin_lock_irqsave(&vha->work_lock, flags);
 	if (vha->scan.scan_flags == 0) {
 		ql_dbg(ql_dbg_disc, vha, 0xffff, "%s: schedule\n", __func__);
 		vha->scan.scan_flags |= SF_QUEUED;
+		vha->scan.rscn_gen_start = atomic_read(&vha->rscn_gen);
 		schedule_delayed_work(&vha->scan.scan_work, 5);
 	}
 	spin_unlock_irqrestore(&vha->work_lock, flags);
@@ -1885,12 +2021,17 @@
 	int rc, h;
 	unsigned long flags;
 
-	rc = qla24xx_async_abort_cmd(sp, false);
+	if (sp->type == SRB_MARKER)
+		rc = QLA_FUNCTION_FAILED;
+	else
+		rc = qla24xx_async_abort_cmd(sp, false);
+
 	if (rc) {
 		spin_lock_irqsave(sp->qpair->qp_lock_ptr, flags);
 		for (h = 1; h < sp->qpair->req->num_outstanding_cmds; h++) {
 			if (sp->qpair->req->outstanding_cmds[h] == sp) {
 				sp->qpair->req->outstanding_cmds[h] = NULL;
+				qla_put_fw_resources(sp->qpair, &sp->iores);
 				break;
 			}
 		}
@@ -1901,45 +2042,176 @@
 	}
 }
 
-static void qla2x00_tmf_sp_done(srb_t *sp, int res)
+static void qla_marker_sp_done(srb_t *sp, int res)
 {
 	struct srb_iocb *tmf = &sp->u.iocb_cmd;
 
+	if (res != QLA_SUCCESS)
+		ql_dbg(ql_dbg_taskm, sp->vha, 0x8004,
+		    "Async-marker fail hdl=%x portid=%06x ctrl=%x lun=%lld qp=%d.\n",
+		    sp->handle, sp->fcport->d_id.b24, sp->u.iocb_cmd.u.tmf.flags,
+		    sp->u.iocb_cmd.u.tmf.lun, sp->qpair->id);
+
+	sp->u.iocb_cmd.u.tmf.data = res;
 	complete(&tmf->u.tmf.comp);
 }
 
-int
-qla2x00_async_tm_cmd(fc_port_t *fcport, uint32_t flags, uint32_t lun,
-	uint32_t tag)
+#define  START_SP_W_RETRIES(_sp, _rval, _chip_gen, _login_gen) \
+{\
+	int cnt = 5; \
+	do { \
+		if (_chip_gen != sp->vha->hw->chip_reset || _login_gen != sp->fcport->login_gen) {\
+			_rval = EINVAL; \
+			break; \
+		} \
+		_rval = qla2x00_start_sp(_sp); \
+		if (_rval == EAGAIN) \
+			msleep(1); \
+		else \
+			break; \
+		cnt--; \
+	} while (cnt); \
+}
+
+/**
+ * qla26xx_marker: send marker IOCB and wait for the completion of it.
+ * @arg: pointer to argument list.
+ *    It is assume caller will provide an fcport pointer and modifier
+ */
+static int
+qla26xx_marker(struct tmf_arg *arg)
 {
-	struct scsi_qla_host *vha = fcport->vha;
+	struct scsi_qla_host *vha = arg->vha;
 	struct srb_iocb *tm_iocb;
 	srb_t *sp;
 	int rval = QLA_FUNCTION_FAILED;
+	fc_port_t *fcport = arg->fcport;
+	u32 chip_gen, login_gen;
 
-	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
+	if (TMF_NOT_READY(arg->fcport)) {
+		ql_dbg(ql_dbg_taskm, vha, 0x8039,
+		    "FC port not ready for marker loop-id=%x portid=%06x modifier=%x lun=%lld qp=%d.\n",
+		    fcport->loop_id, fcport->d_id.b24,
+		    arg->modifier, arg->lun, arg->qpair->id);
+		return QLA_SUSPENDED;
+	}
+
+	chip_gen = vha->hw->chip_reset;
+	login_gen = fcport->login_gen;
+
+	/* ref: INIT */
+	sp = qla2xxx_get_qpair_sp(vha, arg->qpair, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
+	sp->type = SRB_MARKER;
+	sp->name = "marker";
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha), qla_marker_sp_done);
+	sp->u.iocb_cmd.timeout = qla2x00_tmf_iocb_timeout;
+
 	tm_iocb = &sp->u.iocb_cmd;
+	init_completion(&tm_iocb->u.tmf.comp);
+	tm_iocb->u.tmf.modifier = arg->modifier;
+	tm_iocb->u.tmf.lun = arg->lun;
+	tm_iocb->u.tmf.loop_id = fcport->loop_id;
+	tm_iocb->u.tmf.vp_index = vha->vp_idx;
+
+	START_SP_W_RETRIES(sp, rval, chip_gen, login_gen);
+
+	ql_dbg(ql_dbg_taskm, vha, 0x8006,
+	    "Async-marker hdl=%x loop-id=%x portid=%06x modifier=%x lun=%lld qp=%d rval %d.\n",
+	    sp->handle, fcport->loop_id, fcport->d_id.b24,
+	    arg->modifier, arg->lun, sp->qpair->id, rval);
+
+	if (rval != QLA_SUCCESS) {
+		ql_log(ql_log_warn, vha, 0x8031,
+		    "Marker IOCB send failure (%x).\n", rval);
+		goto done_free_sp;
+	}
+
+	wait_for_completion(&tm_iocb->u.tmf.comp);
+	rval = tm_iocb->u.tmf.data;
+
+	if (rval != QLA_SUCCESS) {
+		ql_log(ql_log_warn, vha, 0x8019,
+		    "Marker failed hdl=%x loop-id=%x portid=%06x modifier=%x lun=%lld qp=%d rval %d.\n",
+		    sp->handle, fcport->loop_id, fcport->d_id.b24,
+		    arg->modifier, arg->lun, sp->qpair->id, rval);
+	}
+
+done_free_sp:
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
+done:
+	return rval;
+}
+
+static void qla2x00_tmf_sp_done(srb_t *sp, int res)
+{
+	struct srb_iocb *tmf = &sp->u.iocb_cmd;
+
+	if (res)
+		tmf->u.tmf.data = res;
+	complete(&tmf->u.tmf.comp);
+}
+
+static int qla_tmf_wait(struct tmf_arg *arg)
+{
+	/* there are only 2 types of error handling that reaches here, lun or target reset */
+	if (arg->flags & (TCF_LUN_RESET | TCF_ABORT_TASK_SET | TCF_CLEAR_TASK_SET))
+		return qla2x00_eh_wait_for_pending_commands(arg->vha,
+		    arg->fcport->d_id.b24, arg->lun, WAIT_LUN);
+	else
+		return qla2x00_eh_wait_for_pending_commands(arg->vha,
+		    arg->fcport->d_id.b24, arg->lun, WAIT_TARGET);
+}
+
+static int
+__qla2x00_async_tm_cmd(struct tmf_arg *arg)
+{
+	struct scsi_qla_host *vha = arg->vha;
+	struct srb_iocb *tm_iocb;
+	srb_t *sp;
+	int rval = QLA_FUNCTION_FAILED;
+	fc_port_t *fcport = arg->fcport;
+	u32 chip_gen, login_gen;
+	u64 jif;
+
+	if (TMF_NOT_READY(arg->fcport)) {
+		ql_dbg(ql_dbg_taskm, vha, 0x8032,
+		    "FC port not ready for TM command loop-id=%x portid=%06x modifier=%x lun=%lld qp=%d.\n",
+		    fcport->loop_id, fcport->d_id.b24,
+		    arg->modifier, arg->lun, arg->qpair->id);
+		return QLA_SUSPENDED;
+	}
+
+	chip_gen = vha->hw->chip_reset;
+	login_gen = fcport->login_gen;
+
+	/* ref: INIT */
+	sp = qla2xxx_get_qpair_sp(vha, arg->qpair, fcport, GFP_KERNEL);
+	if (!sp)
+		goto done;
+
+	qla_vha_mark_busy(vha);
 	sp->type = SRB_TM_CMD;
 	sp->name = "tmf";
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha),
+			      qla2x00_tmf_sp_done);
+	sp->u.iocb_cmd.timeout = qla2x00_tmf_iocb_timeout;
 
-	tm_iocb->timeout = qla2x00_tmf_iocb_timeout;
+	tm_iocb = &sp->u.iocb_cmd;
 	init_completion(&tm_iocb->u.tmf.comp);
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha));
+	tm_iocb->u.tmf.flags = arg->flags;
+	tm_iocb->u.tmf.lun = arg->lun;
 
-	tm_iocb->u.tmf.flags = flags;
-	tm_iocb->u.tmf.lun = lun;
-	tm_iocb->u.tmf.data = tag;
-	sp->done = qla2x00_tmf_sp_done;
+	START_SP_W_RETRIES(sp, rval, chip_gen, login_gen);
 
 	ql_dbg(ql_dbg_taskm, vha, 0x802f,
-	    "Async-tmf hdl=%x loop-id=%x portid=%02x%02x%02x.\n",
-	    sp->handle, fcport->loop_id, fcport->d_id.b.domain,
-	    fcport->d_id.b.area, fcport->d_id.b.al_pa);
+	    "Async-tmf hdl=%x loop-id=%x portid=%06x ctrl=%x lun=%lld qp=%d rval=%x.\n",
+	    sp->handle, fcport->loop_id, fcport->d_id.b24,
+	    arg->flags, arg->lun, sp->qpair->id, rval);
 
-	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS)
 		goto done_free_sp;
 	wait_for_completion(&tm_iocb->u.tmf.comp);
@@ -1952,22 +2224,130 @@
 	}
 
 	if (!test_bit(UNLOADING, &vha->dpc_flags) && !IS_QLAFX00(vha->hw)) {
-		flags = tm_iocb->u.tmf.flags;
-		lun = (uint16_t)tm_iocb->u.tmf.lun;
+		jif = jiffies;
+		if (qla_tmf_wait(arg)) {
+			ql_log(ql_log_info, vha, 0x803e,
+			       "Waited %u ms Nexus=%ld:%06x:%llu.\n",
+			       jiffies_to_msecs(jiffies - jif), vha->host_no,
+			       fcport->d_id.b24, arg->lun);
+		}
 
-		/* Issue Marker IOCB */
-		qla2x00_marker(vha, vha->hw->base_qpair,
-		    fcport->loop_id, lun,
-		    flags == TCF_LUN_RESET ? MK_SYNC_ID_LUN : MK_SYNC_ID);
+		if (chip_gen == vha->hw->chip_reset && login_gen == fcport->login_gen) {
+			rval = qla26xx_marker(arg);
+		} else {
+			ql_log(ql_log_info, vha, 0x803e,
+			       "Skip Marker due to disruption. Nexus=%ld:%06x:%llu.\n",
+			       vha->host_no, fcport->d_id.b24, arg->lun);
+			rval = QLA_FUNCTION_FAILED;
+		}
 	}
+	if (tm_iocb->u.tmf.data)
+		rval = tm_iocb->u.tmf.data;
 
 done_free_sp:
-	sp->free(sp);
-	fcport->flags &= ~FCF_ASYNC_SENT;
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
 
+static void qla_put_tmf(struct tmf_arg *arg)
+{
+	struct scsi_qla_host *vha = arg->vha;
+	struct qla_hw_data *ha = vha->hw;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ha->tgt.sess_lock, flags);
+	ha->active_tmf--;
+	list_del(&arg->tmf_elem);
+	spin_unlock_irqrestore(&ha->tgt.sess_lock, flags);
+}
+
+static
+int qla_get_tmf(struct tmf_arg *arg)
+{
+	struct scsi_qla_host *vha = arg->vha;
+	struct qla_hw_data *ha = vha->hw;
+	unsigned long flags;
+	fc_port_t *fcport = arg->fcport;
+	int rc = 0;
+	struct tmf_arg *t;
+
+	spin_lock_irqsave(&ha->tgt.sess_lock, flags);
+	list_for_each_entry(t, &ha->tmf_active, tmf_elem) {
+		if (t->fcport == arg->fcport && t->lun == arg->lun) {
+			/* reject duplicate TMF */
+			ql_log(ql_log_warn, vha, 0x802c,
+			       "found duplicate TMF.  Nexus=%ld:%06x:%llu.\n",
+			       vha->host_no, fcport->d_id.b24, arg->lun);
+			spin_unlock_irqrestore(&ha->tgt.sess_lock, flags);
+			return -EINVAL;
+		}
+	}
+
+	list_add_tail(&arg->tmf_elem, &ha->tmf_pending);
+	while (ha->active_tmf >= MAX_ACTIVE_TMF) {
+		spin_unlock_irqrestore(&ha->tgt.sess_lock, flags);
+
+		msleep(1);
+
+		spin_lock_irqsave(&ha->tgt.sess_lock, flags);
+		if (TMF_NOT_READY(fcport)) {
+			ql_log(ql_log_warn, vha, 0x802c,
+			    "Unable to acquire TM resource due to disruption.\n");
+			rc = EIO;
+			break;
+		}
+		if (ha->active_tmf < MAX_ACTIVE_TMF &&
+		    list_is_first(&arg->tmf_elem, &ha->tmf_pending))
+			break;
+	}
+
+	list_del(&arg->tmf_elem);
+
+	if (!rc) {
+		ha->active_tmf++;
+		list_add_tail(&arg->tmf_elem, &ha->tmf_active);
+	}
+
+	spin_unlock_irqrestore(&ha->tgt.sess_lock, flags);
+
+	return rc;
+}
+
+int
+qla2x00_async_tm_cmd(fc_port_t *fcport, uint32_t flags, uint64_t lun,
+		     uint32_t tag)
+{
+	struct scsi_qla_host *vha = fcport->vha;
+	struct tmf_arg a;
+	int rval = QLA_SUCCESS;
+
+	if (TMF_NOT_READY(fcport))
+		return QLA_SUSPENDED;
+
+	a.vha = fcport->vha;
+	a.fcport = fcport;
+	a.lun = lun;
+	a.flags = flags;
+	INIT_LIST_HEAD(&a.tmf_elem);
+
+	if (flags & (TCF_LUN_RESET|TCF_ABORT_TASK_SET|TCF_CLEAR_TASK_SET|TCF_CLEAR_ACA)) {
+		a.modifier = MK_SYNC_ID_LUN;
+	} else {
+		a.modifier = MK_SYNC_ID;
+	}
+
+	if (qla_get_tmf(&a))
+		return QLA_FUNCTION_FAILED;
+
+	a.qpair = vha->hw->base_qpair;
+	rval = __qla2x00_async_tm_cmd(&a);
+
+	qla_put_tmf(&a);
+	return rval;
+}
+
 int
 qla24xx_async_abort_command(srb_t *sp)
 {
@@ -2021,13 +2401,6 @@
 		qla24xx_post_gpdb_work(vha, ea->fcport, 0);
 		break;
 	default:
-		if ((ea->iop[0] == LSC_SCODE_ELS_REJECT) &&
-		    (ea->iop[1] == 0x50000)) {   /* reson 5=busy expl:0x0 */
-			set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
-			ea->fcport->fw_login_state = DSC_LS_PLOGI_COMP;
-			break;
-		}
-
 		sp = ea->sp;
 		ql_dbg(ql_dbg_disc, vha, 0x2118,
 		       "%s %d %8phC priority %s, fc4type %x prev try %s\n",
@@ -2047,6 +2420,13 @@
 		}
 
 		if (N2N_TOPO(vha->hw)) {
+			if (ea->fcport->n2n_link_reset_cnt ==
+			    vha->hw->login_retry_count &&
+			    ea->fcport->flags & FCF_FCSP_DEVICE) {
+				/* remote authentication app just started */
+				ea->fcport->n2n_link_reset_cnt = 0;
+			}
+
 			if (ea->fcport->n2n_link_reset_cnt <
 			    vha->hw->login_retry_count) {
 				ea->fcport->n2n_link_reset_cnt++;
@@ -2171,12 +2551,7 @@
 		ql_dbg(ql_dbg_disc, vha, 0x20eb, "%s %d %8phC cmd error %x\n",
 		    __func__, __LINE__, ea->fcport->port_name, ea->data[1]);
 
-		ea->fcport->flags &= ~FCF_ASYNC_SENT;
-		qla2x00_set_fcport_disc_state(ea->fcport, DSC_LOGIN_FAILED);
-		if (ea->data[1] & QLA_LOGIO_LOGIN_RETRIED)
-			set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
-		else
-			qla2x00_mark_device_lost(vha, ea->fcport, 1);
+		qlt_schedule_sess_for_deletion(ea->fcport);
 		break;
 	case MBS_LOOP_ID_USED:
 		/* data[1] = IO PARAM 1 = nport ID  */
@@ -2308,6 +2683,40 @@
 	return rval;
 }
 
+void qla_enable_fce_trace(scsi_qla_host_t *vha)
+{
+	int rval;
+	struct qla_hw_data *ha = vha->hw;
+
+	if (ha->fce) {
+		ha->flags.fce_enabled = 1;
+		memset(ha->fce, 0, fce_calc_size(ha->fce_bufs));
+		rval = qla2x00_enable_fce_trace(vha,
+		    ha->fce_dma, ha->fce_bufs, ha->fce_mb, &ha->fce_bufs);
+
+		if (rval) {
+			ql_log(ql_log_warn, vha, 0x8033,
+			    "Unable to reinitialize FCE (%d).\n", rval);
+			ha->flags.fce_enabled = 0;
+		}
+	}
+}
+
+static void qla_enable_eft_trace(scsi_qla_host_t *vha)
+{
+	int rval;
+	struct qla_hw_data *ha = vha->hw;
+
+	if (ha->eft) {
+		memset(ha->eft, 0, EFT_SIZE);
+		rval = qla2x00_enable_eft_trace(vha, ha->eft_dma, EFT_NUM_BUFFERS);
+
+		if (rval) {
+			ql_log(ql_log_warn, vha, 0x8034,
+			    "Unable to reinitialize EFT (%d).\n", rval);
+		}
+	}
+}
 /*
 * qla2x00_initialize_adapter
 *      Initialize board.
@@ -3310,26 +3719,24 @@
 	return rval;
 }
 
-static void
-qla2x00_init_fce_trace(scsi_qla_host_t *vha)
+int qla2x00_alloc_fce_trace(scsi_qla_host_t *vha)
 {
-	int rval;
 	dma_addr_t tc_dma;
 	void *tc;
 	struct qla_hw_data *ha = vha->hw;
 
 	if (!IS_FWI2_CAPABLE(ha))
-		return;
+		return -EINVAL;
 
 	if (!IS_QLA25XX(ha) && !IS_QLA81XX(ha) && !IS_QLA83XX(ha) &&
 	    !IS_QLA27XX(ha) && !IS_QLA28XX(ha))
-		return;
+		return -EINVAL;
 
 	if (ha->fce) {
 		ql_dbg(ql_dbg_init, vha, 0x00bd,
 		       "%s: FCE Mem is already allocated.\n",
 		       __func__);
-		return;
+		return -EIO;
 	}
 
 	/* Allocate memory for Fibre Channel Event Buffer. */
@@ -3339,30 +3746,30 @@
 		ql_log(ql_log_warn, vha, 0x00be,
 		       "Unable to allocate (%d KB) for FCE.\n",
 		       FCE_SIZE / 1024);
-		return;
-	}
-
-	rval = qla2x00_enable_fce_trace(vha, tc_dma, FCE_NUM_BUFFERS,
-					ha->fce_mb, &ha->fce_bufs);
-	if (rval) {
-		ql_log(ql_log_warn, vha, 0x00bf,
-		       "Unable to initialize FCE (%d).\n", rval);
-		dma_free_coherent(&ha->pdev->dev, FCE_SIZE, tc, tc_dma);
-		return;
+		return -ENOMEM;
 	}
 
 	ql_dbg(ql_dbg_init, vha, 0x00c0,
 	       "Allocated (%d KB) for FCE...\n", FCE_SIZE / 1024);
 
-	ha->flags.fce_enabled = 1;
 	ha->fce_dma = tc_dma;
 	ha->fce = tc;
+	ha->fce_bufs = FCE_NUM_BUFFERS;
+	return 0;
+}
+
+void qla2x00_free_fce_trace(struct qla_hw_data *ha)
+{
+	if (!ha->fce)
+		return;
+	dma_free_coherent(&ha->pdev->dev, FCE_SIZE, ha->fce, ha->fce_dma);
+	ha->fce = NULL;
+	ha->fce_dma = 0;
 }
 
 static void
-qla2x00_init_eft_trace(scsi_qla_host_t *vha)
+qla2x00_alloc_eft_trace(scsi_qla_host_t *vha)
 {
-	int rval;
 	dma_addr_t tc_dma;
 	void *tc;
 	struct qla_hw_data *ha = vha->hw;
@@ -3387,14 +3794,6 @@
 		return;
 	}
 
-	rval = qla2x00_enable_eft_trace(vha, tc_dma, EFT_NUM_BUFFERS);
-	if (rval) {
-		ql_log(ql_log_warn, vha, 0x00c2,
-		       "Unable to initialize EFT (%d).\n", rval);
-		dma_free_coherent(&ha->pdev->dev, EFT_SIZE, tc, tc_dma);
-		return;
-	}
-
 	ql_dbg(ql_dbg_init, vha, 0x00c3,
 	       "Allocated (%d KB) EFT ...\n", EFT_SIZE / 1024);
 
@@ -3402,13 +3801,6 @@
 	ha->eft = tc;
 }
 
-static void
-qla2x00_alloc_offload_mem(scsi_qla_host_t *vha)
-{
-	qla2x00_init_fce_trace(vha);
-	qla2x00_init_eft_trace(vha);
-}
-
 void
 qla2x00_alloc_fw_dump(scsi_qla_host_t *vha)
 {
@@ -3419,6 +3811,14 @@
 	struct rsp_que *rsp = ha->rsp_q_map[0];
 	struct qla2xxx_fw_dump *fw_dump;
 
+	if (ha->fw_dump) {
+		ql_dbg(ql_dbg_init, vha, 0x00bd,
+		    "Firmware dump already allocated.\n");
+		return;
+	}
+
+	ha->fw_dumped = 0;
+	ha->fw_dump_cap_flags = 0;
 	dump_size = fixed_size = mem_size = eft_size = fce_size = mq_size = 0;
 	req_q_size = rsp_q_size = 0;
 
@@ -3429,7 +3829,7 @@
 		mem_size = (ha->fw_memory_size - 0x11000 + 1) *
 		    sizeof(uint16_t);
 	} else if (IS_FWI2_CAPABLE(ha)) {
-		if (IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha))
+		if (IS_QLA83XX(ha))
 			fixed_size = offsetof(struct qla83xx_fw_dump, ext_mem);
 		else if (IS_QLA81XX(ha))
 			fixed_size = offsetof(struct qla81xx_fw_dump, ext_mem);
@@ -3441,8 +3841,7 @@
 		mem_size = (ha->fw_memory_size - 0x100000 + 1) *
 		    sizeof(uint32_t);
 		if (ha->mqenable) {
-			if (!IS_QLA83XX(ha) && !IS_QLA27XX(ha) &&
-			    !IS_QLA28XX(ha))
+			if (!IS_QLA83XX(ha))
 				mq_size = sizeof(struct qla2xxx_mq_chain);
 			/*
 			 * Allocate maximum buffer size for all queues - Q0.
@@ -3456,10 +3855,11 @@
 		if (ha->tgt.atio_ring)
 			mq_size += ha->tgt.atio_q_length * sizeof(request_t);
 
-		qla2x00_init_fce_trace(vha);
-		if (ha->fce)
+		if (ha->fce) {
 			fce_size = sizeof(struct qla2xxx_fce_chain) + FCE_SIZE;
-		qla2x00_init_eft_trace(vha);
+			ha->flags.fce_dump_buf_alloced = 1;
+		}
+		qla2x00_alloc_eft_trace(vha);
 		if (ha->eft)
 			eft_size = EFT_SIZE;
 	}
@@ -3818,29 +4218,61 @@
 	return ha->flags.lr_detected;
 }
 
-void qla_init_iocb_limit(scsi_qla_host_t *vha)
+static void __qla_adjust_iocb_limit(struct qla_qpair *qpair)
 {
-	u16 i, num_qps;
-	u32 limit;
-	struct qla_hw_data *ha = vha->hw;
+	u8 num_qps;
+	u16 limit;
+	struct qla_hw_data *ha = qpair->vha->hw;
 
 	num_qps = ha->num_qpairs + 1;
 	limit = (ha->orig_fw_iocb_count * QLA_IOCB_PCT_LIMIT) / 100;
 
-	ha->base_qpair->fwres.iocbs_total = ha->orig_fw_iocb_count;
-	ha->base_qpair->fwres.iocbs_limit = limit;
-	ha->base_qpair->fwres.iocbs_qp_limit = limit / num_qps;
+	qpair->fwres.iocbs_total = ha->orig_fw_iocb_count;
+	qpair->fwres.iocbs_limit = limit;
+	qpair->fwres.iocbs_qp_limit = limit / num_qps;
+
+	qpair->fwres.exch_total = ha->orig_fw_xcb_count;
+	qpair->fwres.exch_limit = (ha->orig_fw_xcb_count *
+				   QLA_IOCB_PCT_LIMIT) / 100;
+}
+
+void qla_init_iocb_limit(scsi_qla_host_t *vha)
+{
+	u8 i;
+	struct qla_hw_data *ha = vha->hw;
+
+	__qla_adjust_iocb_limit(ha->base_qpair);
 	ha->base_qpair->fwres.iocbs_used = 0;
+	ha->base_qpair->fwres.exch_used  = 0;
+
 	for (i = 0; i < ha->max_qpairs; i++) {
 		if (ha->queue_pair_map[i])  {
-			ha->queue_pair_map[i]->fwres.iocbs_total =
-				ha->orig_fw_iocb_count;
-			ha->queue_pair_map[i]->fwres.iocbs_limit = limit;
-			ha->queue_pair_map[i]->fwres.iocbs_qp_limit =
-				limit / num_qps;
+			__qla_adjust_iocb_limit(ha->queue_pair_map[i]);
 			ha->queue_pair_map[i]->fwres.iocbs_used = 0;
+			ha->queue_pair_map[i]->fwres.exch_used = 0;
 		}
 	}
+
+	ha->fwres.iocb_total = ha->orig_fw_iocb_count;
+	ha->fwres.iocb_limit = (ha->orig_fw_iocb_count * QLA_IOCB_PCT_LIMIT) / 100;
+	ha->fwres.exch_total = ha->orig_fw_xcb_count;
+	ha->fwres.exch_limit = (ha->orig_fw_xcb_count * QLA_IOCB_PCT_LIMIT) / 100;
+
+	atomic_set(&ha->fwres.iocb_used, 0);
+	atomic_set(&ha->fwres.exch_used, 0);
+}
+
+void qla_adjust_iocb_limit(scsi_qla_host_t *vha)
+{
+	u8 i;
+	struct qla_hw_data *ha = vha->hw;
+
+	__qla_adjust_iocb_limit(ha->base_qpair);
+
+	for (i = 0; i < ha->max_qpairs; i++) {
+		if (ha->queue_pair_map[i])
+			__qla_adjust_iocb_limit(ha->queue_pair_map[i]);
+	}
 }
 
 /**
@@ -3857,7 +4289,6 @@
 	struct qla_hw_data *ha = vha->hw;
 	struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
 	unsigned long flags;
-	uint16_t fw_major_version;
 	int done_once = 0;
 
 	if (IS_P3P_TYPE(ha)) {
@@ -3924,7 +4355,6 @@
 					goto failed;
 
 enable_82xx_npiv:
-				fw_major_version = ha->fw_major_version;
 				if (IS_P3P_TYPE(ha))
 					qla82xx_check_md_needed(vha);
 				else
@@ -3953,12 +4383,11 @@
 				if (rval != QLA_SUCCESS)
 					goto failed;
 
-				if (!fw_major_version && !(IS_P3P_TYPE(ha)))
-					qla2x00_alloc_offload_mem(vha);
-
 				if (ql2xallocfwdump && !(IS_P3P_TYPE(ha)))
 					qla2x00_alloc_fw_dump(vha);
 
+				qla_enable_fce_trace(vha);
+				qla_enable_eft_trace(vha);
 			} else {
 				goto failed;
 			}
@@ -4003,8 +4432,7 @@
 			    ha->fw_major_version, ha->fw_minor_version,
 			    ha->fw_subminor_version);
 
-			if (IS_QLA83XX(ha) || IS_QLA27XX(ha) ||
-			    IS_QLA28XX(ha)) {
+			if (IS_QLA83XX(ha)) {
 				ha->flags.fac_supported = 0;
 				rval = QLA_SUCCESS;
 			}
@@ -4187,7 +4615,7 @@
 		 * fw shal not send PRLI after PLOGI Acc
 		 */
 		if (ha->flags.edif_enabled &&
-		    vha->e_dbell.db_flags & EDB_ACTIVE) {
+		    DBELL_ACTIVE(vha)) {
 			ha->fw_options[3] |= BIT_15;
 			ha->flags.n2n_fw_acc_sec = 1;
 		} else {
@@ -4431,17 +4859,24 @@
 			 BIT_6) != 0;
 		ql_dbg(ql_dbg_init, vha, 0x00bc, "FA-WWPN Support: %s.\n",
 		    (ha->flags.fawwpn_enabled) ? "enabled" : "disabled");
+		/* Init_cb will be reused for other command(s).  Save a backup copy of port_name */
+		memcpy(ha->port_name, ha->init_cb->port_name, WWN_SIZE);
 	}
 
+	/* ELS pass through payload is limit by frame size. */
+	if (ha->flags.edif_enabled)
+		mid_init_cb->init_cb.frame_payload_size = cpu_to_le16(ELS_MAX_PAYLOAD);
+
+	QLA_FW_STARTED(ha);
 	rval = qla2x00_init_firmware(vha, ha->init_cb_size);
 next_check:
 	if (rval) {
+		QLA_FW_STOPPED(ha);
 		ql_log(ql_log_fatal, vha, 0x00d2,
 		    "Init Firmware **** FAILED ****.\n");
 	} else {
 		ql_dbg(ql_dbg_init, vha, 0x00d3,
 		    "Init Firmware -- success.\n");
-		QLA_FW_STARTED(ha);
 		vha->u_ql2xexchoffld = vha->u_ql2xiniexchg = 0;
 	}
 
@@ -4732,7 +5167,7 @@
 		if (use_tbl &&
 		    ha->pdev->subsystem_vendor == PCI_VENDOR_ID_QLOGIC &&
 		    index < QLA_MODEL_NAMES)
-			strlcpy(ha->model_desc,
+			strscpy(ha->model_desc,
 			    qla2x00_model_name[index * 2 + 1],
 			    sizeof(ha->model_desc));
 	} else {
@@ -4740,14 +5175,14 @@
 		if (use_tbl &&
 		    ha->pdev->subsystem_vendor == PCI_VENDOR_ID_QLOGIC &&
 		    index < QLA_MODEL_NAMES) {
-			strlcpy(ha->model_number,
+			strscpy(ha->model_number,
 				qla2x00_model_name[index * 2],
 				sizeof(ha->model_number));
-			strlcpy(ha->model_desc,
+			strscpy(ha->model_desc,
 			    qla2x00_model_name[index * 2 + 1],
 			    sizeof(ha->model_desc));
 		} else {
-			strlcpy(ha->model_number, def,
+			strscpy(ha->model_number, def,
 				sizeof(ha->model_number));
 		}
 	}
@@ -5335,15 +5770,13 @@
 			    "LOOP READY.\n");
 			ha->flags.fw_init_done = 1;
 
-			if (ha->flags.edif_enabled &&
-			    !(vha->e_dbell.db_flags & EDB_ACTIVE) &&
-			    N2N_TOPO(vha->hw)) {
-				/*
-				 * use port online to wake up app to get ready
-				 * for authentication
-				 */
-				qla2x00_post_aen_work(vha, FCH_EVT_PORT_ONLINE, 0);
-			}
+			/*
+			 * use link up to wake up app to get ready for
+			 * authentication.
+			 */
+			if (ha->flags.edif_enabled && DBELL_INACTIVE(vha))
+				qla2x00_post_aen_work(vha, FCH_EVT_LINKUP,
+						      ha->link_data_rate);
 
 			/*
 			 * Process any ATIO queue entries that came in
@@ -5408,6 +5841,22 @@
 	return QLA_FUNCTION_FAILED;
 }
 
+static void
+qla_reinitialize_link(scsi_qla_host_t *vha)
+{
+	int rval;
+
+	atomic_set(&vha->loop_state, LOOP_DOWN);
+	atomic_set(&vha->loop_down_timer, LOOP_DOWN_TIME);
+	rval = qla2x00_full_login_lip(vha);
+	if (rval == QLA_SUCCESS) {
+		ql_dbg(ql_dbg_disc, vha, 0xd050, "Link reinitialized\n");
+	} else {
+		ql_dbg(ql_dbg_disc, vha, 0xd051,
+			"Link reinitialization failed (%d)\n", rval);
+	}
+}
+
 /*
  * qla2x00_configure_local_loop
  *	Updates Fibre Channel Device Database with local loop devices.
@@ -5459,6 +5908,19 @@
 		spin_unlock_irqrestore(&vha->work_lock, flags);
 
 		if (vha->scan.scan_retry < MAX_SCAN_RETRIES) {
+			u8 loop_map_entries = 0;
+			int rc;
+
+			rc = qla2x00_get_fcal_position_map(vha, NULL,
+						&loop_map_entries);
+			if (rc == QLA_SUCCESS && loop_map_entries > 1) {
+				/*
+				 * There are devices that are still not logged
+				 * in. Reinitialize to give them a chance.
+				 */
+				qla_reinitialize_link(vha);
+				return QLA_FUNCTION_FAILED;
+			}
 			set_bit(LOCAL_LOOP_UPDATE, &vha->dpc_flags);
 			set_bit(LOOP_RESYNC_NEEDED, &vha->dpc_flags);
 		}
@@ -5547,6 +6009,13 @@
 			memcpy(fcport->node_name, new_fcport->node_name,
 			    WWN_SIZE);
 			fcport->scan_state = QLA_FCPORT_FOUND;
+			if (fcport->login_retry == 0) {
+				fcport->login_retry = vha->hw->login_retry_count;
+				ql_dbg(ql_dbg_disc, vha, 0x2135,
+				    "Port login retry %8phN, lid 0x%04x retry cnt=%d.\n",
+				    fcport->port_name, fcport->loop_id,
+				    fcport->login_retry);
+			}
 			found++;
 			break;
 		}
@@ -5739,6 +6208,8 @@
 void
 qla2x00_update_fcport(scsi_qla_host_t *vha, fc_port_t *fcport)
 {
+	unsigned long flags;
+
 	if (IS_SW_RESV_ADDR(fcport->d_id))
 		return;
 
@@ -5748,7 +6219,11 @@
 	qla2x00_set_fcport_disc_state(fcport, DSC_UPD_FCPORT);
 	fcport->login_retry = vha->hw->login_retry_count;
 	fcport->flags &= ~(FCF_LOGIN_NEEDED | FCF_ASYNC_SENT);
+
+	spin_lock_irqsave(&vha->work_lock, flags);
 	fcport->deleted = 0;
+	spin_unlock_irqrestore(&vha->work_lock, flags);
+
 	if (vha->hw->current_topology == ISP_CFG_NL)
 		fcport->logout_on_delete = 0;
 	else
@@ -5970,6 +6445,8 @@
 		qlt_do_generation_tick(vha, &discovery_gen);
 
 		if (USE_ASYNC_SCAN(ha)) {
+			/* start of scan begins here */
+			vha->scan.rscn_gen_end = atomic_read(&vha->rscn_gen);
 			rval = qla24xx_async_gpnft(vha, FC4_TYPE_FCP_SCSI,
 			    NULL);
 			if (rval)
@@ -7026,24 +7503,27 @@
 	ha->chip_reset++;
 	ha->base_qpair->chip_reset = ha->chip_reset;
 	ha->base_qpair->cmd_cnt = ha->base_qpair->cmd_completion_cnt = 0;
+	ha->base_qpair->prev_completion_cnt = 0;
 	for (i = 0; i < ha->max_qpairs; i++) {
 		if (ha->queue_pair_map[i]) {
 			ha->queue_pair_map[i]->chip_reset =
 				ha->base_qpair->chip_reset;
 			ha->queue_pair_map[i]->cmd_cnt =
 			    ha->queue_pair_map[i]->cmd_completion_cnt = 0;
+			ha->base_qpair->prev_completion_cnt = 0;
 		}
 	}
 
 	/* purge MBox commands */
-	if (atomic_read(&ha->num_pend_mbx_stage3)) {
+	spin_lock_irqsave(&ha->hardware_lock, flags);
+	if (test_bit(MBX_INTR_WAIT, &ha->mbx_cmd_flags)) {
 		clear_bit(MBX_INTR_WAIT, &ha->mbx_cmd_flags);
 		complete(&ha->mbx_intr_comp);
 	}
+	spin_unlock_irqrestore(&ha->hardware_lock, flags);
 
 	i = 0;
-	while (atomic_read(&ha->num_pend_mbx_stage3) ||
-	    atomic_read(&ha->num_pend_mbx_stage2) ||
+	while (atomic_read(&ha->num_pend_mbx_stage2) ||
 	    atomic_read(&ha->num_pend_mbx_stage1)) {
 		msleep(20);
 		i++;
@@ -7121,12 +7601,12 @@
 int
 qla2x00_abort_isp(scsi_qla_host_t *vha)
 {
-	int rval;
 	uint8_t        status = 0;
 	struct qla_hw_data *ha = vha->hw;
 	struct scsi_qla_host *vp, *tvp;
 	struct req_que *req = ha->req_q_map[0];
 	unsigned long flags;
+	fc_port_t *fcport;
 
 	if (vha->flags.online) {
 		qla2x00_abort_isp_cleanup(vha);
@@ -7192,6 +7672,15 @@
 			       "ISP Abort - ISP reg disconnect post nvmram config, exiting.\n");
 			return status;
 		}
+
+		/* User may have updated [fcp|nvme] prefer in flash */
+		list_for_each_entry(fcport, &vha->vp_fcports, list) {
+			if (NVME_PRIORITY(ha, fcport))
+				fcport->do_prli_nvme = 1;
+			else
+				fcport->do_prli_nvme = 0;
+		}
+
 		if (!qla2x00_restart_isp(vha)) {
 			clear_bit(RESET_MARKER_NEEDED, &vha->dpc_flags);
 
@@ -7212,31 +7701,7 @@
 
 			if (IS_QLA81XX(ha) || IS_QLA8031(ha))
 				qla2x00_get_fw_version(vha);
-			if (ha->fce) {
-				ha->flags.fce_enabled = 1;
-				memset(ha->fce, 0,
-				    fce_calc_size(ha->fce_bufs));
-				rval = qla2x00_enable_fce_trace(vha,
-				    ha->fce_dma, ha->fce_bufs, ha->fce_mb,
-				    &ha->fce_bufs);
-				if (rval) {
-					ql_log(ql_log_warn, vha, 0x8033,
-					    "Unable to reinitialize FCE "
-					    "(%d).\n", rval);
-					ha->flags.fce_enabled = 0;
-				}
-			}
 
-			if (ha->eft) {
-				memset(ha->eft, 0, EFT_SIZE);
-				rval = qla2x00_enable_eft_trace(vha,
-				    ha->eft_dma, EFT_NUM_BUFFERS);
-				if (rval) {
-					ql_log(ql_log_warn, vha, 0x8034,
-					    "Unable to reinitialize EFT "
-					    "(%d).\n", rval);
-				}
-			}
 		} else {	/* failed the ISP abort */
 			vha->flags.online = 1;
 			if (test_bit(ISP_ABORT_RETRY, &vha->dpc_flags)) {
@@ -7286,6 +7751,14 @@
 				atomic_inc(&vp->vref_count);
 				spin_unlock_irqrestore(&ha->vport_slock, flags);
 
+				/* User may have updated [fcp|nvme] prefer in flash */
+				list_for_each_entry(fcport, &vp->vp_fcports, list) {
+					if (NVME_PRIORITY(ha, fcport))
+						fcport->do_prli_nvme = 1;
+					else
+						fcport->do_prli_nvme = 0;
+				}
+
 				qla2x00_vp_abort_isp(vp);
 
 				spin_lock_irqsave(&ha->vport_slock, flags);
@@ -7833,15 +8306,21 @@
 	struct qla27xx_image_status pri_aux_image_status, sec_aux_image_status;
 	bool valid_pri_image = false, valid_sec_image = false;
 	bool active_pri_image = false, active_sec_image = false;
+	int rc;
 
 	if (!ha->flt_region_aux_img_status_pri) {
 		ql_dbg(ql_dbg_init, vha, 0x018a, "Primary aux image not addressed\n");
 		goto check_sec_image;
 	}
 
-	qla24xx_read_flash_data(vha, (uint32_t *)&pri_aux_image_status,
+	rc = qla24xx_read_flash_data(vha, (uint32_t *)&pri_aux_image_status,
 	    ha->flt_region_aux_img_status_pri,
 	    sizeof(pri_aux_image_status) >> 2);
+	if (rc) {
+		ql_log(ql_log_info, vha, 0x01a1,
+		    "Unable to read Primary aux image(%x).\n", rc);
+		goto check_sec_image;
+	}
 	qla27xx_print_image(vha, "Primary aux image", &pri_aux_image_status);
 
 	if (qla28xx_check_aux_image_status_signature(&pri_aux_image_status)) {
@@ -7872,9 +8351,15 @@
 		goto check_valid_image;
 	}
 
-	qla24xx_read_flash_data(vha, (uint32_t *)&sec_aux_image_status,
+	rc = qla24xx_read_flash_data(vha, (uint32_t *)&sec_aux_image_status,
 	    ha->flt_region_aux_img_status_sec,
 	    sizeof(sec_aux_image_status) >> 2);
+	if (rc) {
+		ql_log(ql_log_info, vha, 0x01a2,
+		    "Unable to read Secondary aux image(%x).\n", rc);
+		goto check_valid_image;
+	}
+
 	qla27xx_print_image(vha, "Secondary aux image", &sec_aux_image_status);
 
 	if (qla28xx_check_aux_image_status_signature(&sec_aux_image_status)) {
@@ -7931,6 +8416,7 @@
 	struct qla27xx_image_status pri_image_status, sec_image_status;
 	bool valid_pri_image = false, valid_sec_image = false;
 	bool active_pri_image = false, active_sec_image = false;
+	int rc;
 
 	if (!ha->flt_region_img_status_pri) {
 		ql_dbg(ql_dbg_init, vha, 0x018a, "Primary image not addressed\n");
@@ -7972,8 +8458,14 @@
 		goto check_valid_image;
 	}
 
-	qla24xx_read_flash_data(vha, (uint32_t *)(&sec_image_status),
+	rc = qla24xx_read_flash_data(vha, (uint32_t *)(&sec_image_status),
 	    ha->flt_region_img_status_sec, sizeof(sec_image_status) >> 2);
+	if (rc) {
+		ql_log(ql_log_info, vha, 0x01a3,
+		    "Unable to read Secondary image status(%x).\n", rc);
+		goto check_valid_image;
+	}
+
 	qla27xx_print_image(vha, "Secondary image", &sec_image_status);
 
 	if (qla27xx_check_image_status_signature(&sec_image_status)) {
@@ -8045,11 +8537,10 @@
 	    "FW: Loading firmware from flash (%x).\n", faddr);
 
 	dcode = (uint32_t *)req->ring;
-	qla24xx_read_flash_data(vha, dcode, faddr, 8);
-	if (qla24xx_risc_firmware_invalid(dcode)) {
+	rval = qla24xx_read_flash_data(vha, dcode, faddr, 8);
+	if (rval || qla24xx_risc_firmware_invalid(dcode)) {
 		ql_log(ql_log_fatal, vha, 0x008c,
-		    "Unable to verify the integrity of flash firmware "
-		    "image.\n");
+		    "Unable to verify the integrity of flash firmware image (rval %x).\n", rval);
 		ql_log(ql_log_fatal, vha, 0x008d,
 		    "Firmware data: %08x %08x %08x %08x.\n",
 		    dcode[0], dcode[1], dcode[2], dcode[3]);
@@ -8063,7 +8554,12 @@
 	for (j = 0; j < segments; j++) {
 		ql_dbg(ql_dbg_init, vha, 0x008d,
 		    "-> Loading segment %u...\n", j);
-		qla24xx_read_flash_data(vha, dcode, faddr, 10);
+		rval = qla24xx_read_flash_data(vha, dcode, faddr, 10);
+		if (rval) {
+			ql_log(ql_log_fatal, vha, 0x016a,
+			    "-> Unable to read segment addr + size .\n");
+			return QLA_FUNCTION_FAILED;
+		}
 		risc_addr = be32_to_cpu((__force __be32)dcode[2]);
 		risc_size = be32_to_cpu((__force __be32)dcode[3]);
 		if (!*srisc_addr) {
@@ -8079,7 +8575,13 @@
 			ql_dbg(ql_dbg_init, vha, 0x008e,
 			    "-> Loading fragment %u: %#x <- %#x (%#lx dwords)...\n",
 			    fragment, risc_addr, faddr, dlen);
-			qla24xx_read_flash_data(vha, dcode, faddr, dlen);
+			rval = qla24xx_read_flash_data(vha, dcode, faddr, dlen);
+			if (rval) {
+				ql_log(ql_log_fatal, vha, 0x016b,
+				    "-> Unable to read fragment(faddr %#x dlen %#lx).\n",
+				    faddr, dlen);
+				return QLA_FUNCTION_FAILED;
+			}
 			for (i = 0; i < dlen; i++)
 				dcode[i] = swab32(dcode[i]);
 
@@ -8108,7 +8610,14 @@
 		fwdt->length = 0;
 
 		dcode = (uint32_t *)req->ring;
-		qla24xx_read_flash_data(vha, dcode, faddr, 7);
+
+		rval = qla24xx_read_flash_data(vha, dcode, faddr, 7);
+		if (rval) {
+			ql_log(ql_log_fatal, vha, 0x016c,
+			    "-> Unable to read template size.\n");
+			goto failed;
+		}
+
 		risc_size = be32_to_cpu((__force __be32)dcode[2]);
 		ql_dbg(ql_dbg_init, vha, 0x0161,
 		    "-> fwdt%u template array at %#x (%#x dwords)\n",
@@ -8134,11 +8643,12 @@
 		}
 
 		dcode = fwdt->template;
-		qla24xx_read_flash_data(vha, dcode, faddr, risc_size);
+		rval = qla24xx_read_flash_data(vha, dcode, faddr, risc_size);
 
-		if (!qla27xx_fwdt_template_valid(dcode)) {
+		if (rval || !qla27xx_fwdt_template_valid(dcode)) {
 			ql_log(ql_log_warn, vha, 0x0165,
-			    "-> fwdt%u failed template validate\n", j);
+			    "-> fwdt%u failed template validate (rval %x)\n",
+			    j, rval);
 			goto failed;
 		}
 
@@ -9332,8 +9842,9 @@
 		qpair->req = ha->req_q_map[req_id];
 		qpair->rsp->req = qpair->req;
 		qpair->rsp->qpair = qpair;
-		/* init qpair to this cpu. Will adjust at run time. */
-		qla_cpu_update(qpair, smp_processor_id());
+
+		if (!qpair->cpu_mapped)
+			qla_cpu_update(qpair, raw_smp_processor_id());
 
 		if (IS_T10_PI_CAPABLE(ha) && ql2xenabledif) {
 			if (ha->fw_attributes & BIT_4)
@@ -9591,6 +10102,12 @@
 
 	vha->hw->flags.port_isolated = 1;
 
+	if (qla2x00_isp_reg_stat(vha->hw)) {
+		ql_log(ql_log_info, vha, 0x9006,
+		    "PCI/Register disconnect, exiting.\n");
+		qla_pci_set_eeh_busy(vha);
+		return FAILED;
+	}
 	if (qla2x00_chip_is_down(vha))
 		return 0;
 
@@ -9606,6 +10123,13 @@
 {
 	scsi_qla_host_t *vha = shost_priv(host);
 
+	if (qla2x00_isp_reg_stat(vha->hw)) {
+		ql_log(ql_log_info, vha, 0x9001,
+		    "PCI/Register disconnect, exiting.\n");
+		qla_pci_set_eeh_busy(vha);
+		return FAILED;
+	}
+
 	vha->hw->flags.port_isolated = 0;
 	/* Set the flag to 1, so that isp_abort can proceed */
 	vha->flags.online = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_inline.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_inline.h
@@ -109,11 +109,13 @@
 {
 	int old_val;
 	uint8_t shiftbits, mask;
+	uint8_t port_dstate_str_sz;
 
 	/* This will have to change when the max no. of states > 16 */
 	shiftbits = 4;
 	mask = (1 << shiftbits) - 1;
 
+	port_dstate_str_sz = sizeof(port_dstate_str) / sizeof(char *);
 	fcport->disc_state = state;
 	while (1) {
 		old_val = atomic_read(&fcport->shadow_disc_state);
@@ -121,7 +123,8 @@
 		    old_val, (old_val << shiftbits) | state)) {
 			ql_dbg(ql_dbg_disc, fcport->vha, 0x2134,
 			    "FCPort %8phC disc_state transition: %s to %s - portid=%06x.\n",
-			    fcport->port_name, port_dstate_str[old_val & mask],
+			    fcport->port_name, (old_val & mask) < port_dstate_str_sz ?
+				    port_dstate_str[old_val & mask] : "Unknown",
 			    port_dstate_str[state], fcport->d_id.b24);
 			return;
 		}
@@ -184,6 +187,8 @@
 	sp->vha = vha;
 	sp->qpair = qpair;
 	sp->cmd_type = TYPE_SRB;
+	/* ref : INIT - normal flow */
+	kref_init(&sp->cmd_kref);
 	INIT_LIST_HEAD(&sp->elem);
 }
 
@@ -223,11 +228,9 @@
 qla2x00_get_sp(scsi_qla_host_t *vha, fc_port_t *fcport, gfp_t flag)
 {
 	srb_t *sp = NULL;
-	uint8_t bail;
 	struct qla_qpair *qpair;
 
-	QLA_VHA_MARK_BUSY(vha, bail);
-	if (unlikely(bail))
+	if (unlikely(qla_vha_mark_busy(vha)))
 		return NULL;
 
 	qpair = vha->hw->base_qpair;
@@ -380,24 +383,27 @@
 
 enum {
 	RESOURCE_NONE,
-	RESOURCE_INI,
+	RESOURCE_IOCB = BIT_0,
+	RESOURCE_EXCH = BIT_1,  /* exchange */
+	RESOURCE_FORCE = BIT_2,
+	RESOURCE_HA = BIT_3,
 };
 
 static inline int
-qla_get_iocbs(struct qla_qpair *qp, struct iocb_resource *iores)
+qla_get_fw_resources(struct qla_qpair *qp, struct iocb_resource *iores)
 {
 	u16 iocbs_used, i;
-	struct qla_hw_data *ha = qp->vha->hw;
+	u16 exch_used;
+	struct qla_hw_data *ha = qp->hw;
 
 	if (!ql2xenforce_iocb_limit) {
 		iores->res_type = RESOURCE_NONE;
 		return 0;
 	}
+	if (iores->res_type & RESOURCE_FORCE)
+		goto force;
 
-	if ((iores->iocb_cnt + qp->fwres.iocbs_used) < qp->fwres.iocbs_qp_limit) {
-		qp->fwres.iocbs_used += iores->iocb_cnt;
-		return 0;
-	} else {
+	if ((iores->iocb_cnt + qp->fwres.iocbs_used) >= qp->fwres.iocbs_qp_limit) {
 		/* no need to acquire qpair lock. It's just rough calculation */
 		iocbs_used = ha->base_qpair->fwres.iocbs_used;
 		for (i = 0; i < ha->max_qpairs; i++) {
@@ -405,30 +411,103 @@
 				iocbs_used += ha->queue_pair_map[i]->fwres.iocbs_used;
 		}
 
-		if ((iores->iocb_cnt + iocbs_used) < qp->fwres.iocbs_limit) {
-			qp->fwres.iocbs_used += iores->iocb_cnt;
-			return 0;
-		} else {
+		if ((iores->iocb_cnt + iocbs_used) >= qp->fwres.iocbs_limit) {
+			iores->res_type = RESOURCE_NONE;
+			return -ENOSPC;
+		}
+	}
+
+	if (iores->res_type & RESOURCE_EXCH) {
+		exch_used = ha->base_qpair->fwres.exch_used;
+		for (i = 0; i < ha->max_qpairs; i++) {
+			if (ha->queue_pair_map[i])
+				exch_used += ha->queue_pair_map[i]->fwres.exch_used;
+		}
+
+		if ((exch_used + iores->exch_cnt) >= qp->fwres.exch_limit) {
+			iores->res_type = RESOURCE_NONE;
+			return -ENOSPC;
+		}
+	}
+
+	if (ql2xenforce_iocb_limit == 2) {
+		if ((iores->iocb_cnt + atomic_read(&ha->fwres.iocb_used)) >=
+		    ha->fwres.iocb_limit) {
 			iores->res_type = RESOURCE_NONE;
 			return -ENOSPC;
 		}
+
+		if (iores->res_type & RESOURCE_EXCH) {
+			if ((iores->exch_cnt + atomic_read(&ha->fwres.exch_used)) >=
+			    ha->fwres.exch_limit) {
+				iores->res_type = RESOURCE_NONE;
+				return -ENOSPC;
+			}
+		}
+	}
+
+force:
+	qp->fwres.iocbs_used += iores->iocb_cnt;
+	qp->fwres.exch_used += iores->exch_cnt;
+	if (ql2xenforce_iocb_limit == 2) {
+		atomic_add(iores->iocb_cnt, &ha->fwres.iocb_used);
+		atomic_add(iores->exch_cnt, &ha->fwres.exch_used);
+		iores->res_type |= RESOURCE_HA;
+	}
+	return 0;
+}
+
+/*
+ * decrement to zero.  This routine will not decrement below zero
+ * @v:  pointer of type atomic_t
+ * @amount: amount to decrement from v
+ */
+static void qla_atomic_dtz(atomic_t *v, int amount)
+{
+	int c, old, dec;
+
+	c = atomic_read(v);
+	for (;;) {
+		dec = c - amount;
+		if (unlikely(dec < 0))
+			dec = 0;
+
+		old = atomic_cmpxchg((v), c, dec);
+		if (likely(old == c))
+			break;
+		c = old;
 	}
 }
 
 static inline void
-qla_put_iocbs(struct qla_qpair *qp, struct iocb_resource *iores)
+qla_put_fw_resources(struct qla_qpair *qp, struct iocb_resource *iores)
 {
-	switch (iores->res_type) {
-	case RESOURCE_NONE:
-		break;
-	default:
+	struct qla_hw_data *ha = qp->hw;
+
+	if (iores->res_type & RESOURCE_HA) {
+		if (iores->res_type & RESOURCE_IOCB)
+			qla_atomic_dtz(&ha->fwres.iocb_used, iores->iocb_cnt);
+
+		if (iores->res_type & RESOURCE_EXCH)
+			qla_atomic_dtz(&ha->fwres.exch_used, iores->exch_cnt);
+	}
+
+	if (iores->res_type & RESOURCE_IOCB) {
 		if (qp->fwres.iocbs_used >= iores->iocb_cnt) {
 			qp->fwres.iocbs_used -= iores->iocb_cnt;
 		} else {
-			// should not happen
+			/* should not happen */
 			qp->fwres.iocbs_used = 0;
 		}
-		break;
+	}
+
+	if (iores->res_type & RESOURCE_EXCH) {
+		if (qp->fwres.exch_used >= iores->exch_cnt) {
+			qp->fwres.exch_used -= iores->exch_cnt;
+		} else {
+			/* should not happen */
+			qp->fwres.exch_used = 0;
+		}
 	}
 	iores->res_type = RESOURCE_NONE;
 }
@@ -494,3 +573,69 @@
 {
 	return !fcport_is_smaller(fcport);
 }
+
+static inline struct qla_qpair *
+qla_mapq_nvme_select_qpair(struct qla_hw_data *ha, struct qla_qpair *qpair)
+{
+	int cpuid = raw_smp_processor_id();
+
+	if (qpair->cpuid != cpuid &&
+	    ha->qp_cpu_map[cpuid]) {
+		qpair = ha->qp_cpu_map[cpuid];
+	}
+	return qpair;
+}
+
+static inline void
+qla_mapq_init_qp_cpu_map(struct qla_hw_data *ha,
+			 struct qla_msix_entry *msix,
+			 struct qla_qpair *qpair)
+{
+	const struct cpumask *mask;
+	unsigned int cpu;
+
+	if (!ha->qp_cpu_map)
+		return;
+	mask = pci_irq_get_affinity(ha->pdev, msix->vector_base0);
+	if (!mask)
+		return;
+	qpair->cpuid = cpumask_first(mask);
+	for_each_cpu(cpu, mask) {
+		ha->qp_cpu_map[cpu] = qpair;
+	}
+	msix->cpuid = qpair->cpuid;
+	qpair->cpu_mapped = true;
+}
+
+static inline void
+qla_mapq_free_qp_cpu_map(struct qla_hw_data *ha)
+{
+	if (ha->qp_cpu_map) {
+		kfree(ha->qp_cpu_map);
+		ha->qp_cpu_map = NULL;
+	}
+}
+
+static inline int qla_mapq_alloc_qp_cpu_map(struct qla_hw_data *ha)
+{
+	scsi_qla_host_t *vha = pci_get_drvdata(ha->pdev);
+
+	if (!ha->qp_cpu_map) {
+		ha->qp_cpu_map = kcalloc(NR_CPUS, sizeof(struct qla_qpair *),
+					 GFP_KERNEL);
+		if (!ha->qp_cpu_map) {
+			ql_log(ql_log_fatal, vha, 0x0180,
+			       "Unable to allocate memory for qp_cpu_map ptrs.\n");
+			return -1;
+		}
+	}
+	return 0;
+}
+
+static inline bool val_is_in_range(u32 val, u32 start, u32 end)
+{
+	if (val >= start && val <= end)
+		return true;
+	else
+		return false;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_iocb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_iocb.c
@@ -522,21 +522,25 @@
 		return (QLA_FUNCTION_FAILED);
 	}
 
+	mrk24 = (struct mrk_entry_24xx *)mrk;
+
 	mrk->entry_type = MARKER_TYPE;
 	mrk->modifier = type;
 	if (type != MK_SYNC_ALL) {
 		if (IS_FWI2_CAPABLE(ha)) {
-			mrk24 = (struct mrk_entry_24xx *) mrk;
 			mrk24->nport_handle = cpu_to_le16(loop_id);
 			int_to_scsilun(lun, (struct scsi_lun *)&mrk24->lun);
 			host_to_fcp_swap(mrk24->lun, sizeof(mrk24->lun));
 			mrk24->vp_index = vha->vp_idx;
-			mrk24->handle = make_handle(req->id, mrk24->handle);
 		} else {
 			SET_TARGET_ID(ha, mrk->target, loop_id);
 			mrk->lun = cpu_to_le16((uint16_t)lun);
 		}
 	}
+
+	if (IS_FWI2_CAPABLE(ha))
+		mrk24->handle = QLA_SKIP_HANDLE;
+
 	wmb();
 
 	qla2x00_start_iocbs(vha, req);
@@ -603,7 +607,8 @@
 	put_unaligned_le32(COMMAND_TYPE_6, &cmd_pkt->entry_type);
 
 	/* No data transfer */
-	if (!scsi_bufflen(cmd) || cmd->sc_data_direction == DMA_NONE) {
+	if (!scsi_bufflen(cmd) || cmd->sc_data_direction == DMA_NONE ||
+	    tot_dsds == 0) {
 		cmd_pkt->byte_count = cpu_to_le32(0);
 		return 0;
 	}
@@ -1589,9 +1594,10 @@
 	tot_dsds = nseg;
 	req_cnt = qla24xx_calc_iocbs(vha, tot_dsds);
 
-	sp->iores.res_type = RESOURCE_INI;
+	sp->iores.res_type = RESOURCE_IOCB | RESOURCE_EXCH;
+	sp->iores.exch_cnt = 1;
 	sp->iores.iocb_cnt = req_cnt;
-	if (qla_get_iocbs(sp->qpair, &sp->iores))
+	if (qla_get_fw_resources(sp->qpair, &sp->iores))
 		goto queuing_error;
 
 	if (req->cnt < (req_cnt + 2)) {
@@ -1678,7 +1684,7 @@
 	if (tot_dsds)
 		scsi_dma_unmap(cmd);
 
-	qla_put_iocbs(sp->qpair, &sp->iores);
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(&ha->hardware_lock, flags);
 
 	return QLA_FUNCTION_FAILED;
@@ -1793,9 +1799,10 @@
 	tot_prot_dsds = nseg;
 	tot_dsds += nseg;
 
-	sp->iores.res_type = RESOURCE_INI;
+	sp->iores.res_type = RESOURCE_IOCB | RESOURCE_EXCH;
+	sp->iores.exch_cnt = 1;
 	sp->iores.iocb_cnt = qla24xx_calc_iocbs(vha, tot_dsds);
-	if (qla_get_iocbs(sp->qpair, &sp->iores))
+	if (qla_get_fw_resources(sp->qpair, &sp->iores))
 		goto queuing_error;
 
 	if (req->cnt < (req_cnt + 2)) {
@@ -1883,7 +1890,7 @@
 	}
 	/* Cleanup will be performed by the caller (queuecommand) */
 
-	qla_put_iocbs(sp->qpair, &sp->iores);
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(&ha->hardware_lock, flags);
 
 	return QLA_FUNCTION_FAILED;
@@ -1952,9 +1959,10 @@
 	tot_dsds = nseg;
 	req_cnt = qla24xx_calc_iocbs(vha, tot_dsds);
 
-	sp->iores.res_type = RESOURCE_INI;
+	sp->iores.res_type = RESOURCE_IOCB | RESOURCE_EXCH;
+	sp->iores.exch_cnt = 1;
 	sp->iores.iocb_cnt = req_cnt;
-	if (qla_get_iocbs(sp->qpair, &sp->iores))
+	if (qla_get_fw_resources(sp->qpair, &sp->iores))
 		goto queuing_error;
 
 	if (req->cnt < (req_cnt + 2)) {
@@ -2041,7 +2049,7 @@
 	if (tot_dsds)
 		scsi_dma_unmap(cmd);
 
-	qla_put_iocbs(sp->qpair, &sp->iores);
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(&qpair->qp_lock, flags);
 
 	return QLA_FUNCTION_FAILED;
@@ -2171,9 +2179,10 @@
 	tot_prot_dsds = nseg;
 	tot_dsds += nseg;
 
-	sp->iores.res_type = RESOURCE_INI;
+	sp->iores.res_type = RESOURCE_IOCB | RESOURCE_EXCH;
+	sp->iores.exch_cnt = 1;
 	sp->iores.iocb_cnt = qla24xx_calc_iocbs(vha, tot_dsds);
-	if (qla_get_iocbs(sp->qpair, &sp->iores))
+	if (qla_get_fw_resources(sp->qpair, &sp->iores))
 		goto queuing_error;
 
 	if (req->cnt < (req_cnt + 2)) {
@@ -2260,7 +2269,7 @@
 	}
 	/* Cleanup will be performed by the caller (queuecommand) */
 
-	qla_put_iocbs(sp->qpair, &sp->iores);
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(&qpair->qp_lock, flags);
 
 	return QLA_FUNCTION_FAILED;
@@ -2537,7 +2546,7 @@
 	scsi_qla_host_t *vha = fcport->vha;
 	struct qla_hw_data *ha = vha->hw;
 	struct srb_iocb *iocb = &sp->u.iocb_cmd;
-	struct req_que *req = vha->req;
+	struct req_que *req = sp->qpair->req;
 
 	flags = iocb->u.tmf.flags;
 	lun = iocb->u.tmf.lun;
@@ -2553,18 +2562,73 @@
 	tsk->port_id[2] = fcport->d_id.b.domain;
 	tsk->vp_index = fcport->vha->vp_idx;
 
-	if (flags == TCF_LUN_RESET) {
+	if (flags & (TCF_LUN_RESET | TCF_ABORT_TASK_SET|
+	    TCF_CLEAR_TASK_SET|TCF_CLEAR_ACA)) {
 		int_to_scsilun(lun, &tsk->lun);
 		host_to_fcp_swap((uint8_t *)&tsk->lun,
 			sizeof(tsk->lun));
 	}
 }
 
-void qla2x00_init_timer(srb_t *sp, unsigned long tmo)
+static void
+qla2x00_async_done(struct srb *sp, int res)
+{
+	if (del_timer(&sp->u.iocb_cmd.timer)) {
+		/*
+		 * Successfully cancelled the timeout handler
+		 * ref: TMR
+		 */
+		if (kref_put(&sp->cmd_kref, qla2x00_sp_release))
+			return;
+	}
+	sp->async_done(sp, res);
+}
+
+void
+qla2x00_sp_release(struct kref *kref)
+{
+	struct srb *sp = container_of(kref, struct srb, cmd_kref);
+	struct scsi_qla_host *vha = sp->vha;
+
+	switch (sp->type) {
+	case SRB_CT_PTHRU_CMD:
+		/* GPSC & GFPNID use fcport->ct_desc.ct_sns for both req & rsp */
+		if (sp->u.iocb_cmd.u.ctarg.req &&
+			(!sp->fcport ||
+			 sp->u.iocb_cmd.u.ctarg.req != sp->fcport->ct_desc.ct_sns)) {
+			dma_free_coherent(&vha->hw->pdev->dev,
+			    sp->u.iocb_cmd.u.ctarg.req_allocated_size,
+			    sp->u.iocb_cmd.u.ctarg.req,
+			    sp->u.iocb_cmd.u.ctarg.req_dma);
+			sp->u.iocb_cmd.u.ctarg.req = NULL;
+		}
+		if (sp->u.iocb_cmd.u.ctarg.rsp &&
+			(!sp->fcport ||
+			 sp->u.iocb_cmd.u.ctarg.rsp != sp->fcport->ct_desc.ct_sns)) {
+			dma_free_coherent(&vha->hw->pdev->dev,
+			    sp->u.iocb_cmd.u.ctarg.rsp_allocated_size,
+			    sp->u.iocb_cmd.u.ctarg.rsp,
+			    sp->u.iocb_cmd.u.ctarg.rsp_dma);
+			sp->u.iocb_cmd.u.ctarg.rsp = NULL;
+		}
+		break;
+	default:
+		break;
+	}
+
+	sp->free(sp);
+}
+
+void
+qla2x00_init_async_sp(srb_t *sp, unsigned long tmo,
+		     void (*done)(struct srb *sp, int res))
 {
 	timer_setup(&sp->u.iocb_cmd.timer, qla2x00_sp_timeout, 0);
-	sp->u.iocb_cmd.timer.expires = jiffies + tmo * HZ;
+	sp->done = qla2x00_async_done;
+	sp->async_done = done;
 	sp->free = qla2x00_sp_free;
+	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
+	sp->u.iocb_cmd.timer.expires = jiffies + tmo * HZ;
 	if (IS_QLAFX00(sp->vha->hw) && sp->type == SRB_FXIOCB_DCMD)
 		init_completion(&sp->u.iocb_cmd.u.fxiocb.fxiocb_comp);
 	sp->start_timer = 1;
@@ -2574,7 +2638,8 @@
 {
 	struct srb_iocb *elsio = &sp->u.iocb_cmd;
 
-	kfree(sp->fcport);
+	if (sp->fcport)
+		qla2x00_free_fcport(sp->fcport);
 
 	if (elsio->u.els_logo.els_logo_pyld)
 		dma_free_coherent(&sp->vha->hw->pdev->dev, DMA_POOL_SIZE,
@@ -2651,10 +2716,12 @@
 	       return -ENOMEM;
 	}
 
-	/* Alloc SRB structure */
+	/* Alloc SRB structure
+	 * ref: INIT
+	 */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp) {
-		kfree(fcport);
+		qla2x00_free_fcport(fcport);
 		ql_log(ql_log_info, vha, 0x70e6,
 		 "SRB allocation failed\n");
 		return -ENOMEM;
@@ -2672,18 +2739,20 @@
 	sp->type = SRB_ELS_DCMD;
 	sp->name = "ELS_DCMD";
 	sp->fcport = fcport;
-	elsio->timeout = qla2x00_els_dcmd_iocb_timeout;
-	qla2x00_init_timer(sp, ELS_DCMD_TIMEOUT);
-	init_completion(&sp->u.iocb_cmd.u.els_logo.comp);
-	sp->done = qla2x00_els_dcmd_sp_done;
+	qla2x00_init_async_sp(sp, ELS_DCMD_TIMEOUT,
+			      qla2x00_els_dcmd_sp_done);
 	sp->free = qla2x00_els_dcmd_sp_free;
+	sp->u.iocb_cmd.timeout = qla2x00_els_dcmd_iocb_timeout;
+	init_completion(&sp->u.iocb_cmd.u.els_logo.comp);
 
 	elsio->u.els_logo.els_logo_pyld = dma_alloc_coherent(&ha->pdev->dev,
 			    DMA_POOL_SIZE, &elsio->u.els_logo.els_logo_pyld_dma,
 			    GFP_KERNEL);
 
 	if (!elsio->u.els_logo.els_logo_pyld) {
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
+		qla2x00_free_fcport(fcport);
 		return QLA_FUNCTION_FAILED;
 	}
 
@@ -2706,7 +2775,9 @@
 
 	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS) {
-		sp->free(sp);
+		/* ref: INIT */
+		kref_put(&sp->cmd_kref, qla2x00_sp_release);
+		qla2x00_free_fcport(fcport);
 		return QLA_FUNCTION_FAILED;
 	}
 
@@ -2717,7 +2788,8 @@
 
 	wait_for_completion(&elsio->u.els_logo.comp);
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	return rval;
 }
 
@@ -2787,7 +2859,7 @@
 	sp->vha->qla_stats.control_requests++;
 }
 
-static void
+void
 qla2x00_els_dcmd2_iocb_timeout(void *data)
 {
 	srb_t *sp = data;
@@ -2850,7 +2922,9 @@
 	    sp->name, res, sp->handle, fcport->d_id.b24, fcport->port_name);
 
 	fcport->flags &= ~(FCF_ASYNC_SENT|FCF_ASYNC_ACTIVE);
-	del_timer(&sp->u.iocb_cmd.timer);
+	/* For edif, set logout on delete to ensure any residual key from FW is flushed.*/
+	fcport->logout_on_delete = 1;
+	fcport->chip_reset = vha->hw->base_qpair->chip_reset;
 
 	if (sp->flags & SRB_WAKEUP_ON_COMP)
 		complete(&lio->u.els_plogi.comp);
@@ -2927,6 +3001,7 @@
 					set_bit(ISP_ABORT_NEEDED,
 					    &vha->dpc_flags);
 					qla2xxx_wake_dpc(vha);
+					break;
 				}
 				fallthrough;
 			default:
@@ -2936,9 +3011,7 @@
 				    fw_status[0], fw_status[1], fw_status[2]);
 
 				fcport->flags &= ~FCF_ASYNC_SENT;
-				qla2x00_set_fcport_disc_state(fcport,
-				    DSC_LOGIN_FAILED);
-				set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
+				qlt_schedule_sess_for_deletion(fcport);
 				break;
 			}
 			break;
@@ -2950,8 +3023,7 @@
 			    fw_status[0], fw_status[1], fw_status[2]);
 
 			sp->fcport->flags &= ~FCF_ASYNC_SENT;
-			qla2x00_set_fcport_disc_state(fcport, DSC_LOGIN_FAILED);
-			set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
+			qlt_schedule_sess_for_deletion(fcport);
 			break;
 		}
 
@@ -2960,7 +3032,8 @@
 			struct srb_iocb *elsio = &sp->u.iocb_cmd;
 
 			qla2x00_els_dcmd2_free(vha, &elsio->u.els_plogi);
-			sp->free(sp);
+			/* ref: INIT */
+			kref_put(&sp->cmd_kref, qla2x00_sp_release);
 			return;
 		}
 		e->u.iosb.sp = sp;
@@ -2970,7 +3043,7 @@
 
 int
 qla24xx_els_dcmd2_iocb(scsi_qla_host_t *vha, int els_opcode,
-    fc_port_t *fcport, bool wait)
+			fc_port_t *fcport)
 {
 	srb_t *sp;
 	struct srb_iocb *elsio = NULL;
@@ -2978,13 +3051,14 @@
 	int rval = QLA_SUCCESS;
 	void	*ptr, *resp_ptr;
 
-	/* Alloc SRB structure */
+	/* Alloc SRB structure
+	 * ref: INIT
+	 */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp) {
 		ql_log(ql_log_info, vha, 0x70e6,
 		 "SRB allocation failed\n");
-		fcport->flags &= ~FCF_ASYNC_ACTIVE;
-		return -ENOMEM;
+		goto done;
 	}
 
 	fcport->flags |= FCF_ASYNC_SENT;
@@ -2996,14 +3070,10 @@
 	sp->type = SRB_ELS_DCMD;
 	sp->name = "ELS_DCMD";
 	sp->fcport = fcport;
+	qla2x00_init_async_sp(sp, ELS_DCMD_TIMEOUT + 2,
+			     qla2x00_els_dcmd2_sp_done);
+	sp->u.iocb_cmd.timeout = qla2x00_els_dcmd2_iocb_timeout;
 
-	elsio->timeout = qla2x00_els_dcmd2_iocb_timeout;
-	if (wait)
-		sp->flags = SRB_WAKEUP_ON_COMP;
-
-	qla2x00_init_timer(sp, ELS_DCMD_TIMEOUT + 2);
-
-	sp->done = qla2x00_els_dcmd2_sp_done;
 	elsio->u.els_plogi.tx_size = elsio->u.els_plogi.rx_size = DMA_POOL_SIZE;
 
 	ptr = elsio->u.els_plogi.els_plogi_pyld =
@@ -3012,7 +3082,7 @@
 
 	if (!elsio->u.els_plogi.els_plogi_pyld) {
 		rval = QLA_FUNCTION_FAILED;
-		goto out;
+		goto done_free_sp;
 	}
 
 	resp_ptr = elsio->u.els_plogi.els_resp_pyld =
@@ -3021,7 +3091,7 @@
 
 	if (!elsio->u.els_plogi.els_resp_pyld) {
 		rval = QLA_FUNCTION_FAILED;
-		goto out;
+		goto done_free_sp;
 	}
 
 	ql_dbg(ql_dbg_io, vha, 0x3073, "PLOGI %p %p\n", ptr, resp_ptr);
@@ -3034,10 +3104,8 @@
 	elsio->u.els_plogi.els_cmd = els_opcode;
 	elsio->u.els_plogi.els_plogi_pyld->opcode = els_opcode;
 
-	if (els_opcode == ELS_DCMD_PLOGI && vha->hw->flags.edif_enabled &&
-	    vha->e_dbell.db_flags & EDB_ACTIVE) {
+	if (els_opcode == ELS_DCMD_PLOGI && DBELL_ACTIVE(vha)) {
 		struct fc_els_flogi *p = ptr;
-
 		p->fl_csp.sp_features |= cpu_to_be16(FC_SP_FT_SEC);
 	}
 
@@ -3046,10 +3114,11 @@
 	    (uint8_t *)elsio->u.els_plogi.els_plogi_pyld,
 	    sizeof(*elsio->u.els_plogi.els_plogi_pyld));
 
-	init_completion(&elsio->u.els_plogi.comp);
 	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS) {
-		rval = QLA_FUNCTION_FAILED;
+		fcport->flags |= FCF_LOGIN_NEEDED;
+		set_bit(RELOGIN_NEEDED, &vha->dpc_flags);
+		goto done_free_sp;
 	} else {
 		ql_dbg(ql_dbg_disc, vha, 0x3074,
 		    "%s PLOGI sent, hdl=%x, loopid=%x, to port_id %06x from port_id %06x\n",
@@ -3057,20 +3126,15 @@
 		    fcport->d_id.b24, vha->d_id.b24);
 	}
 
-	if (wait) {
-		wait_for_completion(&elsio->u.els_plogi.comp);
-
-		if (elsio->u.els_plogi.comp_status != CS_COMPLETE)
-			rval = QLA_FUNCTION_FAILED;
-	} else {
-		goto done;
-	}
+	return rval;
 
-out:
-	fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
+done_free_sp:
 	qla2x00_els_dcmd2_free(vha, &elsio->u.els_plogi);
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
+	fcport->flags &= ~(FCF_ASYNC_SENT | FCF_ASYNC_ACTIVE);
+	qla2x00_set_fcport_disc_state(fcport, DSC_DELETED);
 	return rval;
 }
 
@@ -3779,6 +3843,79 @@
 	logio->vp_index = sp->fcport->vha->vp_idx;
 }
 
+int qla_get_iocbs_resource(struct srb *sp)
+{
+	bool get_exch;
+	bool push_it_through = false;
+
+	if (!ql2xenforce_iocb_limit) {
+		sp->iores.res_type = RESOURCE_NONE;
+		return 0;
+	}
+	sp->iores.res_type = RESOURCE_NONE;
+
+	switch (sp->type) {
+	case SRB_TM_CMD:
+	case SRB_PRLI_CMD:
+	case SRB_ADISC_CMD:
+		push_it_through = true;
+		fallthrough;
+	case SRB_LOGIN_CMD:
+	case SRB_ELS_CMD_RPT:
+	case SRB_ELS_CMD_HST:
+	case SRB_ELS_CMD_HST_NOLOGIN:
+	case SRB_CT_CMD:
+	case SRB_NVME_LS:
+	case SRB_ELS_DCMD:
+		get_exch = true;
+		break;
+
+	case SRB_FXIOCB_DCMD:
+	case SRB_FXIOCB_BCMD:
+		sp->iores.res_type = RESOURCE_NONE;
+		return 0;
+
+	case SRB_SA_UPDATE:
+	case SRB_SA_REPLACE:
+	case SRB_MB_IOCB:
+	case SRB_ABT_CMD:
+	case SRB_NACK_PLOGI:
+	case SRB_NACK_PRLI:
+	case SRB_NACK_LOGO:
+	case SRB_LOGOUT_CMD:
+	case SRB_CTRL_VP:
+	case SRB_MARKER:
+	default:
+		push_it_through = true;
+		get_exch = false;
+	}
+
+	sp->iores.res_type |= RESOURCE_IOCB;
+	sp->iores.iocb_cnt = 1;
+	if (get_exch) {
+		sp->iores.res_type |= RESOURCE_EXCH;
+		sp->iores.exch_cnt = 1;
+	}
+	if (push_it_through)
+		sp->iores.res_type |= RESOURCE_FORCE;
+
+	return qla_get_fw_resources(sp->qpair, &sp->iores);
+}
+
+static void
+qla_marker_iocb(srb_t *sp, struct mrk_entry_24xx *mrk)
+{
+	mrk->entry_type = MARKER_TYPE;
+	mrk->modifier = sp->u.iocb_cmd.u.tmf.modifier;
+	mrk->handle = make_handle(sp->qpair->req->id, sp->handle);
+	if (sp->u.iocb_cmd.u.tmf.modifier != MK_SYNC_ALL) {
+		mrk->nport_handle = cpu_to_le16(sp->u.iocb_cmd.u.tmf.loop_id);
+		int_to_scsilun(sp->u.iocb_cmd.u.tmf.lun, (struct scsi_lun *)&mrk->lun);
+		host_to_fcp_swap(mrk->lun, sizeof(mrk->lun));
+		mrk->vp_index = sp->u.iocb_cmd.u.tmf.vp_index;
+	}
+}
+
 int
 qla2x00_start_sp(srb_t *sp)
 {
@@ -3793,9 +3930,15 @@
 		return -EIO;
 
 	spin_lock_irqsave(qp->qp_lock_ptr, flags);
-	pkt = __qla2x00_alloc_iocbs(sp->qpair, sp);
+	rval = qla_get_iocbs_resource(sp);
+	if (rval) {
+		spin_unlock_irqrestore(qp->qp_lock_ptr, flags);
+		return -EAGAIN;
+	}
+
+	pkt = qla2x00_alloc_iocbs_ready(sp->qpair, sp);
 	if (!pkt) {
-		rval = EAGAIN;
+		rval = -EAGAIN;
 		ql_log(ql_log_warn, vha, 0x700c,
 		    "qla2x00_alloc_iocbs failed.\n");
 		goto done;
@@ -3876,16 +4019,28 @@
 	case SRB_SA_REPLACE:
 		qla24xx_sa_replace_iocb(sp, pkt);
 		break;
+	case SRB_MARKER:
+		qla_marker_iocb(sp, pkt);
+		break;
 	default:
 		break;
 	}
 
-	if (sp->start_timer)
+	if (sp->start_timer) {
+		/* ref: TMR timer ref
+		 * this code should be just before start_iocbs function
+		 * This will make sure that caller function don't to do
+		 * kref_put even on failure
+		 */
+		kref_get(&sp->cmd_kref);
 		add_timer(&sp->u.iocb_cmd.timer);
+	}
 
 	wmb();
 	qla2x00_start_iocbs(vha, qp->req);
 done:
+	if (rval)
+		qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(qp->qp_lock_ptr, flags);
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_isr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_isr.c
@@ -1121,8 +1121,12 @@
 	unsigned long	flags;
 	fc_port_t	*fcport = NULL;
 
-	if (!vha->hw->flags.fw_started)
+	if (!vha->hw->flags.fw_started) {
+		ql_log(ql_log_warn, vha, 0x50ff,
+		    "Dropping AEN - %04x %04x %04x %04x.\n",
+		    mb[0], mb[1], mb[2], mb[3]);
 		return;
+	}
 
 	/* Setup to process RIO completion. */
 	handle_cnt = 0;
@@ -1354,9 +1358,7 @@
 			if (!vha->vp_idx) {
 				if (ha->flags.fawwpn_enabled &&
 				    (ha->current_topology == ISP_CFG_F)) {
-					void *wwpn = ha->init_cb->port_name;
-
-					memcpy(vha->port_name, wwpn, WWN_SIZE);
+					memcpy(vha->port_name, ha->port_name, WWN_SIZE);
 					fc_host_port_name(vha->host) =
 					    wwn_to_u64(vha->port_name);
 					ql_dbg(ql_dbg_init + ql_dbg_verbose,
@@ -1899,6 +1901,8 @@
 	}
 
 	req->outstanding_cmds[index] = NULL;
+
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 	return sp;
 }
 
@@ -2494,6 +2498,7 @@
 		iocb->u.tmf.data = QLA_FUNCTION_FAILED;
 	} else if ((le16_to_cpu(sts->scsi_status) &
 	    SS_RESPONSE_INFO_LEN_VALID)) {
+		host_to_fcp_swap(sts->data, sizeof(sts->data));
 		if (le32_to_cpu(sts->rsp_data_len) < 4) {
 			ql_log(ql_log_warn, fcport->vha, 0x503b,
 			    "Async-%s error - hdl=%x not enough response(%d).\n",
@@ -2512,7 +2517,6 @@
 	case CS_PORT_BUSY:
 	case CS_INCOMPLETE:
 	case CS_PORT_UNAVAILABLE:
-	case CS_TIMEOUT:
 	case CS_RESET:
 		if (atomic_read(&fcport->state) == FCS_ONLINE) {
 			ql_dbg(ql_dbg_disc, fcport->vha, 0x3021,
@@ -2634,7 +2638,7 @@
 	}
 
 	if (unlikely(logit))
-		ql_log(ql_dbg_io, fcport->vha, 0x5060,
+		ql_dbg(ql_dbg_io, fcport->vha, 0x5060,
 		   "NVME-%s ERR Handling - hdl=%x status(%x) tr_len:%x resid=%x  ox_id=%x\n",
 		   sp->name, sp->handle, comp_status,
 		   fd->transferred_length, le32_to_cpu(sts->residual_len),
@@ -3185,7 +3189,7 @@
 		}
 		return;
 	}
-	qla_put_iocbs(sp->qpair, &sp->iores);
+	qla_put_fw_resources(sp->qpair, &sp->iores);
 
 	if (sp->cmd_type != TYPE_SRB) {
 		req->outstanding_cmds[handle] = NULL;
@@ -3350,8 +3354,6 @@
 				       "Dropped frame(s) detected (0x%x of 0x%x bytes).\n",
 				       resid, scsi_bufflen(cp));
 
-				vha->interface_err_cnt++;
-
 				res = DID_ERROR << 16 | lscsi_status;
 				goto check_scsi_status;
 			}
@@ -3421,6 +3423,7 @@
 	case CS_PORT_UNAVAILABLE:
 	case CS_TIMEOUT:
 	case CS_RESET:
+	case CS_EDIF_INV_REQ:
 
 		/*
 		 * We are going to have the fc class block the rport
@@ -3491,7 +3494,7 @@
 
 out:
 	if (logit)
-		ql_log(ql_dbg_io, fcport->vha, 0x3022,
+		ql_dbg(ql_dbg_io, fcport->vha, 0x3022,
 		       "FCP command status: 0x%x-0x%x (0x%x) nexus=%ld:%d:%llu portid=%02x%02x%02x oxid=0x%x cdb=%10phN len=0x%x rsp_info=0x%x resid=0x%x fw_resid=0x%x sp=%p cp=%p.\n",
 		       comp_status, scsi_status, res, vha->host_no,
 		       cp->device->id, cp->device->lun, fcport->d_id.b.domain,
@@ -3605,7 +3608,6 @@
 	default:
 		sp = qla2x00_get_sp_from_handle(vha, func, req, pkt);
 		if (sp) {
-			qla_put_iocbs(sp->qpair, &sp->iores);
 			sp->done(sp, res);
 			return 0;
 		}
@@ -3707,12 +3709,11 @@
  * Return: 0 all iocbs has arrived, xx- all iocbs have not arrived.
  */
 static int qla_chk_cont_iocb_avail(struct scsi_qla_host *vha,
-	struct rsp_que *rsp, response_t *pkt)
+	struct rsp_que *rsp, response_t *pkt, u32 rsp_q_in)
 {
-	int start_pkt_ring_index, end_pkt_ring_index, n_ring_index;
-	response_t *end_pkt;
+	int start_pkt_ring_index;
+	u32 iocb_cnt = 0;
 	int rc = 0;
-	u32 rsp_q_in;
 
 	if (pkt->entry_count == 1)
 		return rc;
@@ -3723,38 +3724,44 @@
 	else
 		start_pkt_ring_index = rsp->ring_index - 1;
 
-	if ((start_pkt_ring_index + pkt->entry_count) >= rsp->length)
-		end_pkt_ring_index = start_pkt_ring_index + pkt->entry_count -
-			rsp->length - 1;
+	if (rsp_q_in < start_pkt_ring_index)
+		/* q in ptr is wrapped */
+		iocb_cnt = rsp->length - start_pkt_ring_index + rsp_q_in;
 	else
-		end_pkt_ring_index = start_pkt_ring_index + pkt->entry_count - 1;
+		iocb_cnt = rsp_q_in - start_pkt_ring_index;
 
-	end_pkt = rsp->ring + end_pkt_ring_index;
-
-	/*  next pkt = end_pkt + 1 */
-	n_ring_index = end_pkt_ring_index + 1;
-	if (n_ring_index >= rsp->length)
-		n_ring_index = 0;
-
-	rsp_q_in = rsp->qpair->use_shadow_reg ? *rsp->in_ptr :
-		rd_reg_dword(rsp->rsp_q_in);
-
-	/* rsp_q_in is either wrapped or pointing beyond endpkt */
-	if ((rsp_q_in < start_pkt_ring_index && rsp_q_in < n_ring_index) ||
-			rsp_q_in >= n_ring_index)
-		/* all IOCBs arrived. */
-		rc = 0;
-	else
+	if (iocb_cnt < pkt->entry_count)
 		rc = -EIO;
 
-	ql_dbg(ql_dbg_init + ql_dbg_verbose, vha, 0x5091,
-	    "%s - ring %p pkt %p end pkt %p entry count %#x rsp_q_in %d rc %d\n",
-	    __func__, rsp->ring, pkt, end_pkt, pkt->entry_count,
-	    rsp_q_in, rc);
+	ql_dbg(ql_dbg_init, vha, 0x5091,
+	       "%s - ring %p pkt %p entry count %d iocb_cnt %d rsp_q_in %d rc %d\n",
+	       __func__, rsp->ring, pkt, pkt->entry_count, iocb_cnt, rsp_q_in, rc);
 
 	return rc;
 }
 
+static void qla_marker_iocb_entry(scsi_qla_host_t *vha, struct req_que *req,
+	struct mrk_entry_24xx *pkt)
+{
+	const char func[] = "MRK-IOCB";
+	srb_t *sp;
+	int res = QLA_SUCCESS;
+
+	if (!IS_FWI2_CAPABLE(vha->hw))
+		return;
+
+	sp = qla2x00_get_sp_from_handle(vha, func, req, pkt);
+	if (!sp)
+		return;
+
+	if (pkt->entry_status) {
+		ql_dbg(ql_dbg_taskm, vha, 0x8025, "marker failure.\n");
+		res = QLA_COMMAND_ERROR;
+	}
+	sp->u.iocb_cmd.u.tmf.data = res;
+	sp->done(sp, res);
+}
+
 /**
  * qla24xx_process_response_queue() - Process response queue entries.
  * @vha: SCSI driver HA context
@@ -3767,17 +3774,40 @@
 	struct qla_hw_data *ha = vha->hw;
 	struct purex_entry_24xx *purex_entry;
 	struct purex_item *pure_item;
+	u16 rsp_in = 0, cur_ring_index;
+	int follow_inptr, is_shadow_hba;
 
 	if (!ha->flags.fw_started)
 		return;
 
-	if (rsp->qpair->cpuid != smp_processor_id() || !rsp->qpair->rcv_intr) {
+	if (rsp->qpair->cpuid != raw_smp_processor_id() || !rsp->qpair->rcv_intr) {
 		rsp->qpair->rcv_intr = 1;
-		qla_cpu_update(rsp->qpair, smp_processor_id());
+
+		if (!rsp->qpair->cpu_mapped)
+			qla_cpu_update(rsp->qpair, raw_smp_processor_id());
 	}
 
-	while (rsp->ring_ptr->signature != RESPONSE_PROCESSED) {
+#define __update_rsp_in(_update, _is_shadow_hba, _rsp, _rsp_in)		\
+	do {								\
+		if (_update) {						\
+			_rsp_in = _is_shadow_hba ? *(_rsp)->in_ptr :	\
+				rd_reg_dword_relaxed((_rsp)->rsp_q_in);	\
+		}							\
+	} while (0)
+
+	is_shadow_hba = IS_SHADOW_REG_CAPABLE(ha);
+	follow_inptr = is_shadow_hba ? ql2xrspq_follow_inptr :
+				ql2xrspq_follow_inptr_legacy;
+
+	__update_rsp_in(follow_inptr, is_shadow_hba, rsp, rsp_in);
+
+	while ((likely(follow_inptr &&
+		       rsp->ring_index != rsp_in &&
+		       rsp->ring_ptr->signature != RESPONSE_PROCESSED)) ||
+		       (!follow_inptr &&
+			rsp->ring_ptr->signature != RESPONSE_PROCESSED)) {
 		pkt = (struct sts_entry_24xx *)rsp->ring_ptr;
+		cur_ring_index = rsp->ring_index;
 
 		rsp->ring_index++;
 		if (rsp->ring_index == rsp->length) {
@@ -3855,9 +3885,7 @@
 					(struct nack_to_isp *)pkt);
 			break;
 		case MARKER_TYPE:
-			/* Do nothing in this case, this check is to prevent it
-			 * from falling into default case
-			 */
+			qla_marker_iocb_entry(vha, rsp->req, (struct mrk_entry_24xx *)pkt);
 			break;
 		case ABORT_IOCB_TYPE:
 			qla24xx_abort_iocb_entry(vha, rsp->req,
@@ -3889,6 +3917,8 @@
 				}
 				pure_item = qla27xx_copy_fpin_pkt(vha,
 							  (void **)&pkt, &rsp);
+				__update_rsp_in(follow_inptr, is_shadow_hba,
+						rsp, rsp_in);
 				if (!pure_item)
 					break;
 				qla24xx_queue_purex_item(vha, pure_item,
@@ -3896,7 +3926,17 @@
 				break;
 
 			case ELS_AUTH_ELS:
-				if (qla_chk_cont_iocb_avail(vha, rsp, (response_t *)pkt)) {
+				if (qla_chk_cont_iocb_avail(vha, rsp, (response_t *)pkt, rsp_in)) {
+					/*
+					 * ring_ptr and ring_index were
+					 * pre-incremented above. Reset them
+					 * back to current. Wait for next
+					 * interrupt with all IOCBs to arrive
+					 * and re-process.
+					 */
+					rsp->ring_ptr = (response_t *)pkt;
+					rsp->ring_index = cur_ring_index;
+
 					ql_dbg(ql_dbg_init, vha, 0x5091,
 					    "Defer processing ELS opcode %#x...\n",
 					    purex_entry->els_frame_payload[3]);
@@ -4239,7 +4279,7 @@
 	}
 	ha = qpair->hw;
 
-	queue_work_on(smp_processor_id(), ha->wq, &qpair->q_work);
+	queue_work(ha->wq, &qpair->q_work);
 
 	return IRQ_HANDLED;
 }
@@ -4265,7 +4305,7 @@
 	wrt_reg_dword(&reg->hccr, HCCRX_CLR_RISC_INT);
 	spin_unlock_irqrestore(&ha->hardware_lock, flags);
 
-	queue_work_on(smp_processor_id(), ha->wq, &qpair->q_work);
+	queue_work(ha->wq, &qpair->q_work);
 
 	return IRQ_HANDLED;
 }
@@ -4358,6 +4398,7 @@
 	for (i = 0; i < ha->msix_count; i++) {
 		qentry = &ha->msix_entries[i];
 		qentry->vector = pci_irq_vector(ha->pdev, i);
+		qentry->vector_base0 = i;
 		qentry->entry = i;
 		qentry->have_irq = 0;
 		qentry->in_use = 0;
@@ -4415,16 +4456,12 @@
 	}
 
 	/* Enable MSI-X vector for response queue update for queue 0 */
-	if (IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha)) {
-		if (ha->msixbase && ha->mqiobase &&
-		    (ha->max_rsp_queues > 1 || ha->max_req_queues > 1 ||
-		     ql2xmqsupport))
-			ha->mqenable = 1;
-	} else
-		if (ha->mqiobase &&
-		    (ha->max_rsp_queues > 1 || ha->max_req_queues > 1 ||
-		     ql2xmqsupport))
-			ha->mqenable = 1;
+	if (IS_MQUE_CAPABLE(ha) &&
+	    (ha->msixbase && ha->mqiobase && ha->max_qpairs))
+		ha->mqenable = 1;
+	else
+		ha->mqenable = 0;
+
 	ql_dbg(ql_dbg_multiq, vha, 0xc005,
 	    "mqiobase=%p, max_rsp_queues=%d, max_req_queues=%d.\n",
 	    ha->mqiobase, ha->max_rsp_queues, ha->max_req_queues);
@@ -4589,5 +4626,6 @@
 	}
 	msix->have_irq = 1;
 	msix->handle = qpair;
+	qla_mapq_init_qp_cpu_map(ha, msix, qpair);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_mbx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_mbx.c
@@ -9,6 +9,12 @@
 #include <linux/delay.h>
 #include <linux/gfp.h>
 
+#ifdef CONFIG_PPC
+#define IS_PPCARCH      true
+#else
+#define IS_PPCARCH      false
+#endif
+
 static struct mb_cmd_name {
 	uint16_t cmd;
 	const char *str;
@@ -188,7 +194,7 @@
 	if (ha->flags.purge_mbox || chip_reset != ha->chip_reset ||
 	    ha->flags.eeh_busy) {
 		ql_log(ql_log_warn, vha, 0xd035,
-		       "Error detected: purge[%d] eeh[%d] cmd=0x%x, Exiting.\n",
+		       "Purge mbox: purge[%d] eeh[%d] cmd=0x%x, Exiting.\n",
 		       ha->flags.purge_mbox, ha->flags.eeh_busy, mcp->mb[0]);
 		rval = QLA_ABORTED;
 		goto premature_exit;
@@ -232,6 +238,8 @@
 			ql_dbg(ql_dbg_mbx, vha, 0x1112,
 			    "mbox[%d]<-0x%04x\n", cnt, *iptr);
 			wrt_reg_word(optr, *iptr);
+		} else {
+			wrt_reg_word(optr, 0);
 		}
 
 		mboxes >>= 1;
@@ -265,9 +273,14 @@
 		spin_unlock_irqrestore(&ha->hardware_lock, flags);
 
 		wait_time = jiffies;
-		atomic_inc(&ha->num_pend_mbx_stage3);
 		if (!wait_for_completion_timeout(&ha->mbx_intr_comp,
 		    mcp->tov * HZ)) {
+			ql_dbg(ql_dbg_mbx, vha, 0x117a,
+			    "cmd=%x Timeout.\n", command);
+			spin_lock_irqsave(&ha->hardware_lock, flags);
+			clear_bit(MBX_INTR_WAIT, &ha->mbx_cmd_flags);
+			spin_unlock_irqrestore(&ha->hardware_lock, flags);
+
 			if (chip_reset != ha->chip_reset) {
 				eeh_delay = ha->flags.eeh_busy ? 1 : 0;
 
@@ -276,16 +289,9 @@
 				spin_unlock_irqrestore(&ha->hardware_lock,
 				    flags);
 				atomic_dec(&ha->num_pend_mbx_stage2);
-				atomic_dec(&ha->num_pend_mbx_stage3);
 				rval = QLA_ABORTED;
 				goto premature_exit;
 			}
-			ql_dbg(ql_dbg_mbx, vha, 0x117a,
-			    "cmd=%x Timeout.\n", command);
-			spin_lock_irqsave(&ha->hardware_lock, flags);
-			clear_bit(MBX_INTR_WAIT, &ha->mbx_cmd_flags);
-			spin_unlock_irqrestore(&ha->hardware_lock, flags);
-
 		} else if (ha->flags.purge_mbox ||
 		    chip_reset != ha->chip_reset) {
 			eeh_delay = ha->flags.eeh_busy ? 1 : 0;
@@ -294,11 +300,9 @@
 			ha->flags.mbox_busy = 0;
 			spin_unlock_irqrestore(&ha->hardware_lock, flags);
 			atomic_dec(&ha->num_pend_mbx_stage2);
-			atomic_dec(&ha->num_pend_mbx_stage3);
 			rval = QLA_ABORTED;
 			goto premature_exit;
 		}
-		atomic_dec(&ha->num_pend_mbx_stage3);
 
 		if (time_after(jiffies, wait_time + 5 * HZ))
 			ql_log(ql_log_warn, vha, 0x1015, "cmd=0x%x, waited %d msecs\n",
@@ -728,6 +732,9 @@
 				vha->min_supported_speed =
 				    nv->min_supported_speed;
 			}
+
+			if (IS_PPCARCH)
+				mcp->mb[11] |= BIT_4;
 		}
 
 		if (ha->flags.exlogins_enabled)
@@ -1695,10 +1702,8 @@
 		mcp->in_mb |= MBX_13|MBX_12|MBX_11|MBX_10;
 	if (IS_FWI2_CAPABLE(vha->hw))
 		mcp->in_mb |= MBX_19|MBX_18|MBX_17|MBX_16;
-	if (IS_QLA27XX(vha->hw) || IS_QLA28XX(vha->hw)) {
-		mcp->in_mb |= MBX_15;
-		mcp->out_mb |= MBX_7|MBX_21|MBX_22|MBX_23;
-	}
+	if (IS_QLA27XX(vha->hw) || IS_QLA28XX(vha->hw))
+		mcp->in_mb |= MBX_15|MBX_21|MBX_22|MBX_23;
 
 	mcp->tov = MBX_TOV_SECONDS;
 	mcp->flags = 0;
@@ -2198,6 +2203,9 @@
 	ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x1054,
 	    "Entered %s.\n", __func__);
 
+	if (!ha->flags.fw_started)
+		return QLA_FUNCTION_FAILED;
+
 	mcp->mb[0] = MBC_GET_FIRMWARE_STATE;
 	mcp->out_mb = MBX_0;
 	if (IS_FWI2_CAPABLE(vha->hw))
@@ -3031,8 +3039,7 @@
 		ha->orig_fw_iocb_count = mcp->mb[10];
 		if (ha->flags.npiv_supported)
 			ha->max_npiv_vports = mcp->mb[11];
-		if (IS_QLA81XX(ha) || IS_QLA83XX(ha) || IS_QLA27XX(ha) ||
-		    IS_QLA28XX(ha))
+		if (IS_QLA81XX(ha) || IS_QLA83XX(ha))
 			ha->fw_max_fcf_count = mcp->mb[12];
 	}
 
@@ -3054,7 +3061,8 @@
  *	Kernel context.
  */
 int
-qla2x00_get_fcal_position_map(scsi_qla_host_t *vha, char *pos_map)
+qla2x00_get_fcal_position_map(scsi_qla_host_t *vha, char *pos_map,
+		u8 *num_entries)
 {
 	int rval;
 	mbx_cmd_t mc;
@@ -3094,6 +3102,8 @@
 
 		if (pos_map)
 			memcpy(pos_map, pmap, FCAL_MAP_SIZE);
+		if (num_entries)
+			*num_entries = pmap[0];
 	}
 	dma_pool_free(ha->s_dma_pool, pmap, pmap_dma);
 
@@ -5623,7 +5633,7 @@
 	mcp->out_mb = MBX_1|MBX_0;
 	mcp->in_mb = MBX_2|MBX_1|MBX_0;
 	if (IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha))
-		mcp->in_mb |= MBX_3;
+		mcp->in_mb |= MBX_4|MBX_3;
 	mcp->tov = MBX_TOV_SECONDS;
 	mcp->flags = 0;
 	rval = qla2x00_mailbox_command(vha, mcp);
@@ -6481,23 +6491,21 @@
 	if (!vha->hw->flags.fw_started)
 		goto done;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, NULL, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
-	sp->type = SRB_MB_IOCB;
-	sp->name = mb_to_str(mcp->mb[0]);
-
 	c = &sp->u.iocb_cmd;
-	c->timeout = qla2x00_async_iocb_timeout;
 	init_completion(&c->u.mbx.comp);
 
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	sp->type = SRB_MB_IOCB;
+	sp->name = mb_to_str(mcp->mb[0]);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_mb_sp_done);
 
 	memcpy(sp->u.iocb_cmd.u.mbx.out_mb, mcp->mb, SIZEOF_IOCB_MB_REG);
 
-	sp->done = qla2x00_async_mb_sp_done;
-
 	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS) {
 		ql_dbg(ql_dbg_mbx, vha, 0x1018,
@@ -6529,7 +6537,8 @@
 	}
 
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_mid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_mid.c
@@ -166,9 +166,13 @@
 	int ret = QLA_SUCCESS;
 	fc_port_t *fcport;
 
-	if (vha->hw->flags.edif_enabled)
+	if (vha->hw->flags.edif_enabled) {
+		if (DBELL_ACTIVE(vha))
+			qla2x00_post_aen_work(vha, FCH_EVT_VENDOR_UNIQUE,
+			    FCH_EVT_VENDOR_UNIQUE_VPORT_DOWN);
 		/* delete sessions and flush sa_indexes */
 		qla2x00_wait_for_sess_deletion(vha);
+	}
 
 	if (vha->hw->flags.fw_started)
 		ret = qla24xx_control_vp(vha, VCE_COMMAND_DISABLE_VPS_LOGO_ALL);
@@ -176,7 +180,7 @@
 	atomic_set(&vha->loop_state, LOOP_DOWN);
 	atomic_set(&vha->loop_down_timer, LOOP_DOWN_TIME);
 	list_for_each_entry(fcport, &vha->vp_fcports, list)
-		fcport->logout_on_delete = 0;
+		fcport->logout_on_delete = 1;
 
 	if (!vha->hw->flags.edif_enabled)
 		qla2x00_wait_for_sess_deletion(vha);
@@ -511,6 +515,7 @@
 		return(NULL);
 	}
 
+	vha->irq_offset = QLA_BASE_VECTORS;
 	host = vha->host;
 	fc_vport->dd_data = vha;
 	/* New host info */
@@ -965,6 +970,7 @@
 	if (vp_index == 0 || vp_index >= ha->max_npiv_vports)
 		return QLA_PARAMETER_ERROR;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(base_vha, NULL, GFP_KERNEL);
 	if (!sp)
 		return rval;
@@ -972,9 +978,8 @@
 	sp->type = SRB_CTRL_VP;
 	sp->name = "ctrl_vp";
 	sp->comp = &comp;
-	sp->done = qla_ctrlvp_sp_done;
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha) + 2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla_ctrlvp_sp_done);
 	sp->u.iocb_cmd.u.ctrlvp.cmd = cmd;
 	sp->u.iocb_cmd.u.ctrlvp.vp_index = vp_index;
 
@@ -1008,6 +1013,7 @@
 		break;
 	}
 done:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_mr.c
@@ -691,7 +691,7 @@
 	struct qla_hw_data *ha = vha->hw;
 
 	if (pci_is_pcie(ha->pdev))
-		strlcpy(str, "PCIe iSA", str_len);
+		strscpy(str, "PCIe iSA", str_len);
 	return str;
 }
 
@@ -739,29 +739,6 @@
 }
 
 int
-qlafx00_loop_reset(scsi_qla_host_t *vha)
-{
-	int ret;
-	struct fc_port *fcport;
-	struct qla_hw_data *ha = vha->hw;
-
-	if (ql2xtargetreset) {
-		list_for_each_entry(fcport, &vha->vp_fcports, list) {
-			if (fcport->port_type != FCT_TARGET)
-				continue;
-
-			ret = ha->isp_ops->target_reset(fcport, 0, 0);
-			if (ret != QLA_SUCCESS) {
-				ql_dbg(ql_dbg_taskm, vha, 0x803d,
-				    "Bus Reset failed: Reset=%d "
-				    "d_id=%x.\n", ret, fcport->d_id.b24);
-			}
-		}
-	}
-	return QLA_SUCCESS;
-}
-
-int
 qlafx00_iospace_config(struct qla_hw_data *ha)
 {
 	if (pci_request_selected_regions(ha->pdev, ha->bars,
@@ -1810,17 +1787,18 @@
 	struct register_host_info *preg_hsi;
 	struct new_utsname *p_sysid = NULL;
 
+	/* ref: INIT */
 	sp = qla2x00_get_sp(vha, fcport, GFP_KERNEL);
 	if (!sp)
 		goto done;
 
 	sp->type = SRB_FXIOCB_DCMD;
 	sp->name = "fxdisc";
+	qla2x00_init_async_sp(sp, FXDISC_TIMEOUT,
+			      qla2x00_fxdisc_sp_done);
+	sp->u.iocb_cmd.timeout = qla2x00_fxdisc_iocb_timeout;
 
 	fdisc = &sp->u.iocb_cmd;
-	fdisc->timeout = qla2x00_fxdisc_iocb_timeout;
-	qla2x00_init_timer(sp, FXDISC_TIMEOUT);
-
 	switch (fx_type) {
 	case FXDISC_GET_CONFIG_INFO:
 	fdisc->u.fxiocb.flags =
@@ -1872,21 +1850,21 @@
 			phost_info = &preg_hsi->hsi;
 			memset(preg_hsi, 0, sizeof(struct register_host_info));
 			phost_info->os_type = OS_TYPE_LINUX;
-			strlcpy(phost_info->sysname, p_sysid->sysname,
+			strscpy(phost_info->sysname, p_sysid->sysname,
 				sizeof(phost_info->sysname));
-			strlcpy(phost_info->nodename, p_sysid->nodename,
+			strscpy(phost_info->nodename, p_sysid->nodename,
 				sizeof(phost_info->nodename));
 			if (!strcmp(phost_info->nodename, "(none)"))
 				ha->mr.host_info_resend = true;
-			strlcpy(phost_info->release, p_sysid->release,
+			strscpy(phost_info->release, p_sysid->release,
 				sizeof(phost_info->release));
-			strlcpy(phost_info->version, p_sysid->version,
+			strscpy(phost_info->version, p_sysid->version,
 				sizeof(phost_info->version));
-			strlcpy(phost_info->machine, p_sysid->machine,
+			strscpy(phost_info->machine, p_sysid->machine,
 				sizeof(phost_info->machine));
-			strlcpy(phost_info->domainname, p_sysid->domainname,
+			strscpy(phost_info->domainname, p_sysid->domainname,
 				sizeof(phost_info->domainname));
-			strlcpy(phost_info->hostdriver, QLA2XXX_VERSION,
+			strscpy(phost_info->hostdriver, QLA2XXX_VERSION,
 				sizeof(phost_info->hostdriver));
 			preg_hsi->utc = (uint64_t)ktime_get_real_seconds();
 			ql_dbg(ql_dbg_init, vha, 0x0149,
@@ -1921,7 +1899,6 @@
 	}
 
 	fdisc->u.fxiocb.req_func_type = cpu_to_le16(fx_type);
-	sp->done = qla2x00_fxdisc_sp_done;
 
 	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS)
@@ -1932,9 +1909,9 @@
 	if (fx_type == FXDISC_GET_CONFIG_INFO) {
 		struct config_info_data *pinfo =
 		    (struct config_info_data *) fdisc->u.fxiocb.rsp_addr;
-		strlcpy(vha->hw->model_number, pinfo->model_num,
+		strscpy(vha->hw->model_number, pinfo->model_num,
 			ARRAY_SIZE(vha->hw->model_number));
-		strlcpy(vha->hw->model_desc, pinfo->model_description,
+		strscpy(vha->hw->model_desc, pinfo->model_description,
 			ARRAY_SIZE(vha->hw->model_desc));
 		memcpy(&vha->hw->mr.symbolic_name, pinfo->symbolic_name,
 		    sizeof(vha->hw->mr.symbolic_name));
@@ -1997,7 +1974,8 @@
 		dma_free_coherent(&ha->pdev->dev, fdisc->u.fxiocb.req_len,
 		    fdisc->u.fxiocb.req_addr, fdisc->u.fxiocb.req_dma_handle);
 done_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	return rval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_nvme.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_nvme.c
@@ -27,7 +27,10 @@
 		return 0;
 	}
 
-	if (!vha->nvme_local_port && qla_nvme_register_hba(vha))
+	if (qla_nvme_register_hba(vha))
+		return 0;
+
+	if (!vha->nvme_local_port)
 		return 0;
 
 	if (!(fcport->nvme_prli_service_param &
@@ -127,6 +130,7 @@
 			       "Failed to allocate qpair\n");
 			return -EINVAL;
 		}
+		qla_adjust_iocb_limit(vha);
 	}
 	*handle = qpair;
 
@@ -181,6 +185,7 @@
 	spin_unlock_irqrestore(&priv->cmd_lock, flags);
 
 	fd = priv->fd;
+
 	fd->done(fd, priv->comp_status);
 out:
 	qla2x00_rel_sp(sp);
@@ -228,6 +233,8 @@
 	fc_port_t *fcport = sp->fcport;
 	struct qla_hw_data *ha = fcport->vha->hw;
 	int rval, abts_done_called = 1;
+	bool io_wait_for_abort_done;
+	uint32_t handle;
 
 	ql_dbg(ql_dbg_io, fcport->vha, 0xffff,
 	       "%s called for sp=%p, hndl=%x on fcport=%p desc=%p deleted=%d\n",
@@ -244,12 +251,20 @@
 		goto out;
 	}
 
+	/*
+	 * sp may not be valid after abort_command if return code is either
+	 * SUCCESS or ERR_FROM_FW codes, so cache the value here.
+	 */
+	io_wait_for_abort_done = ql2xabts_wait_nvme &&
+					QLA_ABTS_WAIT_ENABLED(sp);
+	handle = sp->handle;
+
 	rval = ha->isp_ops->abort_command(sp);
 
 	ql_dbg(ql_dbg_io, fcport->vha, 0x212b,
 	    "%s: %s command for sp=%p, handle=%x on fcport=%p rval=%x\n",
 	    __func__, (rval != QLA_SUCCESS) ? "Failed to abort" : "Aborted",
-	    sp, sp->handle, fcport, rval);
+	    sp, handle, fcport, rval);
 
 	/*
 	 * If async tmf is enabled, the abort callback is called only on
@@ -264,7 +279,7 @@
 	 * are waited until ABTS complete. This kref is decreased
 	 * at qla24xx_abort_sp_done function.
 	 */
-	if (abts_done_called && ql2xabts_wait_nvme && QLA_ABTS_WAIT_ENABLED(sp))
+	if (abts_done_called && io_wait_for_abort_done)
 		return;
 out:
 	/* kref_get was done before work was schedule. */
@@ -336,8 +351,7 @@
 	nvme->u.nvme.rsp_len = fd->rsplen;
 	nvme->u.nvme.rsp_dma = fd->rspdma;
 	nvme->u.nvme.timeout_sec = fd->timeout;
-	nvme->u.nvme.cmd_dma = dma_map_single(&ha->pdev->dev, fd->rqstaddr,
-	    fd->rqstlen, DMA_TO_DEVICE);
+	nvme->u.nvme.cmd_dma = fd->rqstdma;
 	dma_sync_single_for_device(&ha->pdev->dev, nvme->u.nvme.cmd_dma,
 	    fd->rqstlen, DMA_TO_DEVICE);
 
@@ -345,7 +359,6 @@
 	if (rval != QLA_SUCCESS) {
 		ql_log(ql_log_warn, vha, 0x700e,
 		    "qla2x00_start_sp failed = %d\n", rval);
-		wake_up(&sp->nvme_ls_waitq);
 		sp->priv = NULL;
 		priv->sp = NULL;
 		qla2x00_rel_sp(sp);
@@ -411,13 +424,24 @@
 		goto queuing_error;
 	}
 	req_cnt = qla24xx_calc_iocbs(vha, tot_dsds);
+
+	sp->iores.res_type = RESOURCE_IOCB | RESOURCE_EXCH;
+	sp->iores.exch_cnt = 1;
+	sp->iores.iocb_cnt = req_cnt;
+	if (qla_get_fw_resources(sp->qpair, &sp->iores)) {
+		rval = -EBUSY;
+		goto queuing_error;
+	}
+
 	if (req->cnt < (req_cnt + 2)) {
 		if (IS_SHADOW_REG_CAPABLE(ha)) {
 			cnt = *req->out_ptr;
 		} else {
 			cnt = rd_reg_dword_relaxed(req->req_q_out);
-			if (qla2x00_check_reg16_for_disconnect(vha, cnt))
+			if (qla2x00_check_reg16_for_disconnect(vha, cnt)) {
+				rval = -EBUSY;
 				goto queuing_error;
+			}
 		}
 
 		if (req->ring_index < cnt)
@@ -562,6 +586,8 @@
 	wrt_reg_dword(req->req_q_in, req->ring_index);
 
 queuing_error:
+	if (rval)
+		qla_put_fw_resources(sp->qpair, &sp->iores);
 	spin_unlock_irqrestore(&qpair->qp_lock, flags);
 
 	return rval;
@@ -575,6 +601,7 @@
 	fc_port_t *fcport;
 	struct srb_iocb *nvme;
 	struct scsi_qla_host *vha;
+	struct qla_hw_data *ha;
 	int rval;
 	srb_t *sp;
 	struct qla_qpair *qpair = hw_queue_handle;
@@ -595,6 +622,7 @@
 		return -ENODEV;
 
 	vha = fcport->vha;
+	ha = vha->hw;
 
 	if (test_bit(ABORT_ISP_ACTIVE, &vha->dpc_flags))
 		return -EBUSY;
@@ -609,12 +637,13 @@
 	if (fcport->nvme_flag & NVME_FLAG_RESETTING)
 		return -EBUSY;
 
+	qpair = qla_mapq_nvme_select_qpair(ha, qpair);
+
 	/* Alloc SRB structure */
 	sp = qla2xxx_get_qpair_sp(vha, qpair, fcport, GFP_ATOMIC);
 	if (!sp)
 		return -EBUSY;
 
-	init_waitqueue_head(&sp->nvme_ls_waitq);
 	kref_init(&sp->cmd_kref);
 	spin_lock_init(&priv->cmd_lock);
 	sp->priv = priv;
@@ -631,9 +660,8 @@
 
 	rval = qla2x00_start_nvme_mq(sp);
 	if (rval != QLA_SUCCESS) {
-		ql_log(ql_log_warn, vha, 0x212d,
+		ql_dbg(ql_dbg_io + ql_dbg_verbose, vha, 0x212d,
 		    "qla2x00_start_nvme_mq failed = %d\n", rval);
-		wake_up(&sp->nvme_ls_waitq);
 		sp->priv = NULL;
 		priv->sp = NULL;
 		qla2xxx_rel_qpair_sp(sp->qpair, sp);
@@ -743,7 +771,6 @@
 	ha = vha->hw;
 	tmpl = &qla_nvme_fc_transport;
 
-	WARN_ON(vha->nvme_local_port);
 
 	qla_nvme_fc_transport.max_hw_queues =
 	    min((uint8_t)(qla_nvme_fc_transport.max_hw_queues),
@@ -754,13 +781,25 @@
 	pinfo.port_role = FC_PORT_ROLE_NVME_INITIATOR;
 	pinfo.port_id = vha->d_id.b24;
 
-	ql_log(ql_log_info, vha, 0xffff,
-	    "register_localport: host-traddr=nn-0x%llx:pn-0x%llx on portID:%x\n",
-	    pinfo.node_name, pinfo.port_name, pinfo.port_id);
-	qla_nvme_fc_transport.dma_boundary = vha->host->dma_boundary;
-
-	ret = nvme_fc_register_localport(&pinfo, tmpl,
-	    get_device(&ha->pdev->dev), &vha->nvme_local_port);
+	mutex_lock(&ha->vport_lock);
+	/*
+	 * Check again for nvme_local_port to see if any other thread raced
+	 * with this one and finished registration.
+	 */
+	if (!vha->nvme_local_port) {
+		ql_log(ql_log_info, vha, 0xffff,
+		    "register_localport: host-traddr=nn-0x%llx:pn-0x%llx on portID:%x\n",
+		    pinfo.node_name, pinfo.port_name, pinfo.port_id);
+		qla_nvme_fc_transport.dma_boundary = vha->host->dma_boundary;
+
+		ret = nvme_fc_register_localport(&pinfo, tmpl,
+						 get_device(&ha->pdev->dev),
+						 &vha->nvme_local_port);
+		mutex_unlock(&ha->vport_lock);
+	} else {
+		mutex_unlock(&ha->vport_lock);
+		return 0;
+	}
 	if (ret) {
 		ql_log(ql_log_warn, vha, 0xffff,
 		    "register_localport failed: ret=%x\n", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_os.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_os.c
@@ -40,10 +40,11 @@
 MODULE_PARM_DESC(ql2xfulldump_on_mpifail,
 		 "Set this to take full dump on MPI hang.");
 
-int ql2xenforce_iocb_limit = 1;
+int ql2xenforce_iocb_limit = 2;
 module_param(ql2xenforce_iocb_limit, int, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(ql2xenforce_iocb_limit,
-		 "Enforce IOCB throttling, to avoid FW congestion. (default: 1)");
+		 "Enforce IOCB throttling, to avoid FW congestion. (default: 2) "
+		 "1: track usage per queue, 2: track usage per adapter");
 
 /*
  * CT6 CTX allocation cache
@@ -202,12 +203,6 @@
 		" 0 -- Regular doorbell.\n"
 		" 1 -- CAMRAM doorbell (faster).\n");
 
-int ql2xtargetreset = 1;
-module_param(ql2xtargetreset, int, S_IRUGO);
-MODULE_PARM_DESC(ql2xtargetreset,
-		 "Enable target reset."
-		 "Default is 1 - use hw defaults.");
-
 int ql2xgffidenable;
 module_param(ql2xgffidenable, int, S_IRUGO);
 MODULE_PARM_DESC(ql2xgffidenable,
@@ -339,6 +334,21 @@
 		 "To wait for ABTS response on I/O timeouts for NVMe. (default: 1)");
 
 
+u32 ql2xdelay_before_pci_error_handling = 5;
+module_param(ql2xdelay_before_pci_error_handling, uint, 0644);
+MODULE_PARM_DESC(ql2xdelay_before_pci_error_handling,
+	"Number of seconds delayed before qla begin PCI error self-handling (default: 5).\n");
+
+int ql2xrspq_follow_inptr = 1;
+module_param(ql2xrspq_follow_inptr, int, 0644);
+MODULE_PARM_DESC(ql2xrspq_follow_inptr,
+		 "Follow RSP IN pointer for RSP updates for HBAs 27xx and newer (default: 1).");
+
+int ql2xrspq_follow_inptr_legacy = 1;
+module_param(ql2xrspq_follow_inptr_legacy, int, 0644);
+MODULE_PARM_DESC(ql2xrspq_follow_inptr_legacy,
+		 "Follow RSP IN pointer for RSP updates for HBAs older than 27XX. (default: 1).");
+
 static void qla2x00_clear_drv_active(struct qla_hw_data *);
 static void qla2x00_free_device(scsi_qla_host_t *);
 static int qla2xxx_map_queues(struct Scsi_Host *shost);
@@ -457,6 +467,11 @@
 			    "Unable to allocate memory for queue pair ptrs.\n");
 			goto fail_qpair_map;
 		}
+		if (qla_mapq_alloc_qp_cpu_map(ha) != 0) {
+			kfree(ha->queue_pair_map);
+			ha->queue_pair_map = NULL;
+			goto fail_qpair_map;
+		}
 	}
 
 	/*
@@ -531,6 +546,7 @@
 		ha->base_qpair = NULL;
 	}
 
+	qla_mapq_free_qp_cpu_map(ha);
 	spin_lock_irqsave(&ha->hardware_lock, flags);
 	for (cnt = 0; cnt < ha->max_req_queues; cnt++) {
 		if (!test_bit(cnt, ha->req_qid_map))
@@ -734,7 +750,8 @@
 	struct scsi_cmnd *cmd = GET_CMD_SP(sp);
 	struct completion *comp = sp->comp;
 
-	sp->free(sp);
+	/* kref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	cmd->result = res;
 	CMD_SP(cmd) = NULL;
 	cmd->scsi_done(cmd);
@@ -825,7 +842,8 @@
 	struct scsi_cmnd *cmd = GET_CMD_SP(sp);
 	struct completion *comp = sp->comp;
 
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 	cmd->result = res;
 	CMD_SP(cmd) = NULL;
 	cmd->scsi_done(cmd);
@@ -925,6 +943,7 @@
 		goto qc24_target_busy;
 
 	sp = scsi_cmd_priv(cmd);
+	/* ref: INIT */
 	qla2xxx_init_sp(sp, vha, vha->hw->base_qpair, fcport);
 
 	sp->u.scmd.cmd = cmd;
@@ -944,7 +963,8 @@
 	return 0;
 
 qc24_host_busy_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 
 qc24_target_busy:
 	return SCSI_MLQUEUE_TARGET_BUSY;
@@ -1014,6 +1034,7 @@
 		goto qc24_target_busy;
 
 	sp = scsi_cmd_priv(cmd);
+	/* ref: INIT */
 	qla2xxx_init_sp(sp, vha, qpair, fcport);
 
 	sp->u.scmd.cmd = cmd;
@@ -1032,7 +1053,8 @@
 	return 0;
 
 qc24_host_busy_free_sp:
-	sp->free(sp);
+	/* ref: INIT */
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 
 qc24_target_busy:
 	return SCSI_MLQUEUE_TARGET_BUSY;
@@ -1258,6 +1280,7 @@
 	uint32_t ratov_j;
 	struct qla_qpair *qpair;
 	unsigned long flags;
+	int fast_fail_status = SUCCESS;
 
 	if (qla2x00_isp_reg_stat(ha)) {
 		ql_log(ql_log_info, vha, 0x8042,
@@ -1266,9 +1289,10 @@
 		return FAILED;
 	}
 
+	/* Save any FAST_IO_FAIL value to return later if abort succeeds */
 	ret = fc_block_scsi_eh(cmd);
 	if (ret != 0)
-		return ret;
+		fast_fail_status = ret;
 
 	sp = scsi_cmd_priv(cmd);
 	qpair = sp->qpair;
@@ -1276,7 +1300,7 @@
 	vha->cmd_timeout_cnt++;
 
 	if ((sp->fcport && sp->fcport->deleted) || !qpair)
-		return SUCCESS;
+		return fast_fail_status != SUCCESS ? fast_fail_status : FAILED;
 
 	spin_lock_irqsave(qpair->qp_lock_ptr, flags);
 	sp->comp = &comp;
@@ -1311,7 +1335,7 @@
 			    __func__, ha->r_a_tov/10);
 			ret = FAILED;
 		} else {
-			ret = SUCCESS;
+			ret = fast_fail_status;
 		}
 		break;
 	default:
@@ -1331,21 +1355,20 @@
 /*
  * Returns: QLA_SUCCESS or QLA_FUNCTION_FAILED.
  */
-int
-qla2x00_eh_wait_for_pending_commands(scsi_qla_host_t *vha, unsigned int t,
-	uint64_t l, enum nexus_wait_type type)
+static int
+__qla2x00_eh_wait_for_pending_commands(struct qla_qpair *qpair, unsigned int t,
+				       uint64_t l, enum nexus_wait_type type)
 {
 	int cnt, match, status;
 	unsigned long flags;
-	struct qla_hw_data *ha = vha->hw;
-	struct req_que *req;
+	scsi_qla_host_t *vha = qpair->vha;
+	struct req_que *req = qpair->req;
 	srb_t *sp;
 	struct scsi_cmnd *cmd;
 
 	status = QLA_SUCCESS;
 
-	spin_lock_irqsave(&ha->hardware_lock, flags);
-	req = vha->req;
+	spin_lock_irqsave(qpair->qp_lock_ptr, flags);
 	for (cnt = 1; status == QLA_SUCCESS &&
 		cnt < req->num_outstanding_cmds; cnt++) {
 		sp = req->outstanding_cmds[cnt];
@@ -1372,15 +1395,35 @@
 		if (!match)
 			continue;
 
-		spin_unlock_irqrestore(&ha->hardware_lock, flags);
+		spin_unlock_irqrestore(qpair->qp_lock_ptr, flags);
 		status = qla2x00_eh_wait_on_command(cmd);
-		spin_lock_irqsave(&ha->hardware_lock, flags);
+		spin_lock_irqsave(qpair->qp_lock_ptr, flags);
 	}
-	spin_unlock_irqrestore(&ha->hardware_lock, flags);
+	spin_unlock_irqrestore(qpair->qp_lock_ptr, flags);
 
 	return status;
 }
 
+int
+qla2x00_eh_wait_for_pending_commands(scsi_qla_host_t *vha, unsigned int t,
+				     uint64_t l, enum nexus_wait_type type)
+{
+	struct qla_qpair *qpair;
+	struct qla_hw_data *ha = vha->hw;
+	int i, status = QLA_SUCCESS;
+
+	status = __qla2x00_eh_wait_for_pending_commands(ha->base_qpair, t, l,
+							type);
+	for (i = 0; status == QLA_SUCCESS && i < ha->max_qpairs; i++) {
+		qpair = ha->queue_pair_map[i];
+		if (!qpair)
+			continue;
+		status = __qla2x00_eh_wait_for_pending_commands(qpair, t, l,
+								type);
+	}
+	return status;
+}
+
 static char *reset_errors[] = {
 	"HBA not online",
 	"HBA not ready",
@@ -1414,7 +1457,7 @@
 		return err;
 
 	if (fcport->deleted)
-		return SUCCESS;
+		return FAILED;
 
 	ql_log(ql_log_info, vha, 0x8009,
 	    "DEVICE RESET ISSUED nexus=%ld:%d:%llu cmd=%p.\n", vha->host_no,
@@ -1434,8 +1477,9 @@
 		goto eh_reset_failed;
 	}
 	err = 3;
-	if (qla2x00_eh_wait_for_pending_commands(vha, sdev->id,
-	    sdev->lun, WAIT_LUN) != QLA_SUCCESS) {
+	if (qla2x00_eh_wait_for_pending_commands(vha, fcport->d_id.b24,
+						 cmd->device->lun,
+						 WAIT_LUN) != QLA_SUCCESS) {
 		ql_log(ql_log_warn, vha, 0x800d,
 		    "wait for pending cmds failed for cmd=%p.\n", cmd);
 		goto eh_reset_failed;
@@ -1482,7 +1526,7 @@
 		return err;
 
 	if (fcport->deleted)
-		return SUCCESS;
+		return FAILED;
 
 	ql_log(ql_log_info, vha, 0x8009,
 	    "TARGET RESET ISSUED nexus=%ld:%d cmd=%p.\n", vha->host_no,
@@ -1501,8 +1545,8 @@
 		goto eh_reset_failed;
 	}
 	err = 3;
-	if (qla2x00_eh_wait_for_pending_commands(vha, sdev->id,
-	    0, WAIT_TARGET) != QLA_SUCCESS) {
+	if (qla2x00_eh_wait_for_pending_commands(vha, fcport->d_id.b24, 0,
+						 WAIT_TARGET) != QLA_SUCCESS) {
 		ql_log(ql_log_warn, vha, 0x800d,
 		    "wait for pending cmds failed for cmd=%p.\n", cmd);
 		goto eh_reset_failed;
@@ -1693,27 +1737,10 @@
 qla2x00_loop_reset(scsi_qla_host_t *vha)
 {
 	int ret;
-	struct fc_port *fcport;
 	struct qla_hw_data *ha = vha->hw;
 
-	if (IS_QLAFX00(ha)) {
-		return qlafx00_loop_reset(vha);
-	}
-
-	if (ql2xtargetreset == 1 && ha->flags.enable_target_reset) {
-		list_for_each_entry(fcport, &vha->vp_fcports, list) {
-			if (fcport->port_type != FCT_TARGET)
-				continue;
-
-			ret = ha->isp_ops->target_reset(fcport, 0, 0);
-			if (ret != QLA_SUCCESS) {
-				ql_dbg(ql_dbg_taskm, vha, 0x802c,
-				    "Bus Reset failed: Reset=%d "
-				    "d_id=%x.\n", ret, fcport->d_id.b24);
-			}
-		}
-	}
-
+	if (IS_QLAFX00(ha))
+		return QLA_SUCCESS;
 
 	if (ha->flags.enable_lip_full_login && !IS_CNA_CAPABLE(ha)) {
 		atomic_set(&vha->loop_state, LOOP_DOWN);
@@ -1796,8 +1823,16 @@
 		}
 
 		spin_lock_irqsave(qp->qp_lock_ptr, *flags);
-		if (ret_cmd && blk_mq_request_started(scsi_cmd_to_rq(cmd)))
-			sp->done(sp, res);
+		switch (sp->type) {
+		case SRB_SCSI_CMD:
+			if (ret_cmd && blk_mq_request_started(scsi_cmd_to_rq(cmd)))
+				sp->done(sp, res);
+			break;
+		default:
+			if (ret_cmd)
+				sp->done(sp, res);
+			break;
+		}
 	} else {
 		sp->done(sp, res);
 	}
@@ -1826,6 +1861,12 @@
 	for (cnt = 1; cnt < req->num_outstanding_cmds; cnt++) {
 		sp = req->outstanding_cmds[cnt];
 		if (sp) {
+			if (qla2x00_chip_is_down(vha)) {
+				req->outstanding_cmds[cnt] = NULL;
+				sp->done(sp, res);
+				continue;
+			}
+
 			switch (sp->cmd_type) {
 			case TYPE_SRB:
 				qla2x00_abort_srb(qp, sp, res, &flags);
@@ -2794,6 +2835,16 @@
 	return atomic_read(&vha->loop_state) == LOOP_READY;
 }
 
+static void qla_heartbeat_work_fn(struct work_struct *work)
+{
+	struct qla_hw_data *ha = container_of(work,
+		struct qla_hw_data, heartbeat_work);
+	struct scsi_qla_host *base_vha = pci_get_drvdata(ha->pdev);
+
+	if (!ha->flags.mbox_busy && base_vha->flags.init_done)
+		qla_no_op_mb(base_vha);
+}
+
 static void qla2x00_iocb_work_fn(struct work_struct *work)
 {
 	struct scsi_qla_host *vha = container_of(work,
@@ -2930,9 +2981,10 @@
 	ha->max_exchg = FW_MAX_EXCHANGES_CNT;
 	atomic_set(&ha->num_pend_mbx_stage1, 0);
 	atomic_set(&ha->num_pend_mbx_stage2, 0);
-	atomic_set(&ha->num_pend_mbx_stage3, 0);
 	atomic_set(&ha->zio_threshold, DEFAULT_ZIO_THRESHOLD);
 	ha->last_zio_threshold = DEFAULT_ZIO_THRESHOLD;
+	INIT_LIST_HEAD(&ha->tmf_pending);
+	INIT_LIST_HEAD(&ha->tmf_active);
 
 	/* Assign ISP specific operations. */
 	if (IS_QLA2100(ha)) {
@@ -3209,6 +3261,13 @@
 	host->max_id = ha->max_fibre_devices;
 	host->cmd_per_lun = 3;
 	host->unique_id = host->host_no;
+
+	if (ql2xenabledif && ql2xenabledif != 2) {
+		ql_log(ql_log_warn, base_vha, 0x302d,
+		       "Invalid value for ql2xenabledif, resetting it to default (2)\n");
+		ql2xenabledif = 2;
+	}
+
 	if (IS_T10_PI_CAPABLE(ha) && ql2xenabledif)
 		host->max_cmd_len = 32;
 	else
@@ -3232,6 +3291,7 @@
 	    host->transportt, sht->vendor_id);
 
 	INIT_WORK(&base_vha->iocb_work, qla2x00_iocb_work_fn);
+	INIT_WORK(&ha->heartbeat_work, qla_heartbeat_work_fn);
 
 	/* Set up the irqs */
 	ret = qla2x00_request_irqs(ha, rsp);
@@ -3441,8 +3501,6 @@
 			base_vha->flags.difdix_supported = 1;
 			ql_dbg(ql_dbg_init, base_vha, 0x00f1,
 			    "Registering for DIF/DIX type 1 and 3 protection.\n");
-			if (ql2xenabledif == 1)
-				prot = SHOST_DIX_TYPE0_PROTECTION;
 			if (ql2xprotmask)
 				scsi_host_set_prot(host, ql2xprotmask);
 			else
@@ -3532,6 +3590,7 @@
 probe_failed:
 	qla_enode_stop(base_vha);
 	qla_edb_stop(base_vha);
+	vfree(base_vha->scan.l);
 	if (base_vha->gnl.l) {
 		dma_free_coherent(&ha->pdev->dev, base_vha->gnl.size,
 				base_vha->gnl.l, base_vha->gnl.ldma);
@@ -3754,8 +3813,7 @@
 		if (ha->mqiobase)
 			iounmap(ha->mqiobase);
 
-		if ((IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha)) &&
-		    ha->msixbase)
+		if (ha->msixbase)
 			iounmap(ha->msixbase);
 	}
 }
@@ -3891,13 +3949,15 @@
 static inline void
 qla24xx_free_purex_list(struct purex_list *list)
 {
-	struct list_head *item, *next;
+	struct purex_item *item, *next;
 	ulong flags;
 
 	spin_lock_irqsave(&list->lock, flags);
-	list_for_each_safe(item, next, &list->head) {
-		list_del(item);
-		kfree(list_entry(item, struct purex_item, list));
+	list_for_each_entry_safe(item, next, &list->head, list) {
+		list_del(&item->list);
+		if (item == &item->vha->default_item)
+			continue;
+		kfree(item);
 	}
 	spin_unlock_irqrestore(&list->lock, flags);
 }
@@ -4358,7 +4418,7 @@
 
 	/* allocate the purex dma pool */
 	ha->purex_dma_pool = dma_pool_create(name, &ha->pdev->dev,
-	    MAX_PAYLOAD, 8, 0);
+	    ELS_MAX_PAYLOAD, 8, 0);
 
 	if (!ha->purex_dma_pool) {
 		ql_dbg_pci(ql_dbg_init, ha->pdev, 0x011b,
@@ -4569,7 +4629,7 @@
 qla2x00_number_of_exch(scsi_qla_host_t *vha, u32 *ret_cnt, u16 max_cnt)
 {
 	u32 temp;
-	struct init_cb_81xx *icb = (struct init_cb_81xx *)&vha->hw->init_cb;
+	struct init_cb_81xx *icb = (struct init_cb_81xx *)vha->hw->init_cb;
 	*ret_cnt = FW_DEF_EXCHANGES_CNT;
 
 	if (max_cnt > vha->hw->max_exchg)
@@ -4999,7 +5059,8 @@
 	}
 	INIT_DELAYED_WORK(&vha->scan.scan_work, qla_scan_work_fn);
 
-	sprintf(vha->host_str, "%s_%lu", QLA2XXX_DRIVER_NAME, vha->host_no);
+	snprintf(vha->host_str, sizeof(vha->host_str), "%s_%lu",
+		 QLA2XXX_DRIVER_NAME, vha->host_no);
 	ql_dbg(ql_dbg_init, vha, 0x0041,
 	    "Allocated the host=%p hw=%p vha=%p dev_name=%s",
 	    vha->host, vha->hw, vha,
@@ -5012,13 +5073,11 @@
 qla2x00_alloc_work(struct scsi_qla_host *vha, enum qla_work_type type)
 {
 	struct qla_work_evt *e;
-	uint8_t bail;
 
 	if (test_bit(UNLOADING, &vha->dpc_flags))
 		return NULL;
 
-	QLA_VHA_MARK_BUSY(vha, bail);
-	if (bail)
+	if (qla_vha_mark_busy(vha))
 		return NULL;
 
 	e = kzalloc(sizeof(struct qla_work_evt), GFP_ATOMIC);
@@ -5466,10 +5525,10 @@
 			break;
 		case QLA_EVT_ELS_PLOGI:
 			qla24xx_els_dcmd2_iocb(vha, ELS_DCMD_PLOGI,
-			    e->u.fcport.fcport, false);
+			    e->u.fcport.fcport);
 			break;
 		case QLA_EVT_SA_REPLACE:
-			qla24xx_issue_sa_replace_iocb(vha, e);
+			rc = qla24xx_issue_sa_replace_iocb(vha, e);
 			break;
 		}
 
@@ -5533,6 +5592,11 @@
 					ea.fcport = fcport;
 					qla24xx_handle_relogin_event(vha, &ea);
 				} else if (vha->hw->current_topology ==
+					 ISP_CFG_NL &&
+					IS_QLA2XXX_MIDTYPE(vha->hw)) {
+					(void)qla24xx_fcport_handle_login(vha,
+									fcport);
+				} else if (vha->hw->current_topology ==
 				    ISP_CFG_NL) {
 					fcport->login_retry--;
 					status =
@@ -6787,12 +6851,15 @@
 	set_user_nice(current, MIN_NICE);
 
 	set_current_state(TASK_INTERRUPTIBLE);
-	while (!kthread_should_stop()) {
+	while (1) {
 		ql_dbg(ql_dbg_dpc, base_vha, 0x4000,
 		    "DPC handler sleeping.\n");
 
 		schedule();
 
+		if (kthread_should_stop())
+			break;
+
 		if (test_and_clear_bit(DO_EEH_RECOVERY, &base_vha->dpc_flags))
 			qla_pci_set_eeh_busy(base_vha);
 
@@ -6805,15 +6872,16 @@
 			goto end_loop;
 		}
 
+		if (test_bit(UNLOADING, &base_vha->dpc_flags))
+			/* don't do any work. Wait to be terminated by kthread_stop */
+			goto end_loop;
+
 		ha->dpc_active = 1;
 
 		ql_dbg(ql_dbg_dpc + ql_dbg_verbose, base_vha, 0x4001,
 		    "DPC handler waking up, dpc_flags=0x%lx.\n",
 		    base_vha->dpc_flags);
 
-		if (test_bit(UNLOADING, &base_vha->dpc_flags))
-			break;
-
 		if (IS_P3P_TYPE(ha)) {
 			if (IS_QLA8044(ha)) {
 				if (test_and_clear_bit(ISP_UNRECOVERABLE,
@@ -7035,9 +7103,12 @@
 			}
 		}
 loop_resync_check:
-		if (test_and_clear_bit(LOOP_RESYNC_NEEDED,
+		if (!qla2x00_reset_active(base_vha) &&
+		    test_and_clear_bit(LOOP_RESYNC_NEEDED,
 		    &base_vha->dpc_flags)) {
-
+			/*
+			 * Allow abort_isp to complete before moving on to scanning.
+			 */
 			ql_dbg(ql_dbg_dpc, base_vha, 0x400f,
 			    "Loop resync scheduled.\n");
 
@@ -7114,17 +7185,6 @@
 			qla2x00_lip_reset(base_vha);
 		}
 
-		if (test_bit(HEARTBEAT_CHK, &base_vha->dpc_flags)) {
-			/*
-			 * if there is a mb in progress then that's
-			 * enough of a check to see if fw is still ticking.
-			 */
-			if (!ha->flags.mbox_busy && base_vha->flags.init_done)
-				qla_no_op_mb(base_vha);
-
-			clear_bit(HEARTBEAT_CHK, &base_vha->dpc_flags);
-		}
-
 		ha->dpc_active = 0;
 end_loop:
 		set_current_state(TASK_INTERRUPTIBLE);
@@ -7139,9 +7199,6 @@
 	 */
 	ha->dpc_active = 0;
 
-	/* Cleanup any residual CTX SRBs. */
-	qla2x00_abort_all_cmds(base_vha, DID_NO_CONNECT << 16);
-
 	return 0;
 }
 
@@ -7183,56 +7240,99 @@
 
 static bool qla_do_heartbeat(struct scsi_qla_host *vha)
 {
-	u64 cmd_cnt, prev_cmd_cnt;
-	bool do_hb = false;
 	struct qla_hw_data *ha = vha->hw;
-	int i;
+	u32 cmpl_cnt;
+	u16 i;
+	bool do_heartbeat = false;
 
-	/* if cmds are still pending down in fw, then do hb */
-	if (ha->base_qpair->cmd_cnt != ha->base_qpair->cmd_completion_cnt) {
-		do_hb = true;
+	/*
+	 * Allow do_heartbeat only if we don’t have any active interrupts,
+	 * but there are still IOs outstanding with firmware.
+	 */
+	cmpl_cnt = ha->base_qpair->cmd_completion_cnt;
+	if (cmpl_cnt == ha->base_qpair->prev_completion_cnt &&
+	    cmpl_cnt != ha->base_qpair->cmd_cnt) {
+		do_heartbeat = true;
 		goto skip;
 	}
+	ha->base_qpair->prev_completion_cnt = cmpl_cnt;
 
 	for (i = 0; i < ha->max_qpairs; i++) {
-		if (ha->queue_pair_map[i] &&
-		    ha->queue_pair_map[i]->cmd_cnt !=
-		    ha->queue_pair_map[i]->cmd_completion_cnt) {
-			do_hb = true;
-			break;
+		if (ha->queue_pair_map[i]) {
+			cmpl_cnt = ha->queue_pair_map[i]->cmd_completion_cnt;
+			if (cmpl_cnt == ha->queue_pair_map[i]->prev_completion_cnt &&
+			    cmpl_cnt != ha->queue_pair_map[i]->cmd_cnt) {
+				do_heartbeat = true;
+				break;
+			}
+			ha->queue_pair_map[i]->prev_completion_cnt = cmpl_cnt;
 		}
 	}
 
 skip:
-	prev_cmd_cnt = ha->prev_cmd_cnt;
-	cmd_cnt = ha->base_qpair->cmd_cnt;
-	for (i = 0; i < ha->max_qpairs; i++) {
-		if (ha->queue_pair_map[i])
-			cmd_cnt += ha->queue_pair_map[i]->cmd_cnt;
-	}
-	ha->prev_cmd_cnt = cmd_cnt;
-
-	if (!do_hb && ((cmd_cnt - prev_cmd_cnt) > 50))
-		/*
-		 * IOs are completing before periodic hb check.
-		 * IOs seems to be running, do hb for sanity check.
-		 */
-		do_hb = true;
-
-	return do_hb;
+	return do_heartbeat;
 }
 
-static void qla_heart_beat(struct scsi_qla_host *vha)
+static void qla_heart_beat(struct scsi_qla_host *vha, u16 dpc_started)
 {
+	struct qla_hw_data *ha = vha->hw;
+
 	if (vha->vp_idx)
 		return;
 
 	if (vha->hw->flags.eeh_busy || qla2x00_chip_is_down(vha))
 		return;
 
+	/*
+	 * dpc thread cannot run if heartbeat is running at the same time.
+	 * We also do not want to starve heartbeat task. Therefore, do
+	 * heartbeat task at least once every 5 seconds.
+	 */
+	if (dpc_started &&
+	    time_before(jiffies, ha->last_heartbeat_run_jiffies + 5 * HZ))
+		return;
+
 	if (qla_do_heartbeat(vha)) {
-		set_bit(HEARTBEAT_CHK, &vha->dpc_flags);
-		qla2xxx_wake_dpc(vha);
+		ha->last_heartbeat_run_jiffies = jiffies;
+		queue_work(ha->wq, &ha->heartbeat_work);
+	}
+}
+
+static void qla_wind_down_chip(scsi_qla_host_t *vha)
+{
+	struct qla_hw_data *ha = vha->hw;
+
+	if (!ha->flags.eeh_busy)
+		return;
+	if (ha->pci_error_state)
+		/* system is trying to recover */
+		return;
+
+	/*
+	 * Current system is not handling PCIE error.  At this point, this is
+	 * best effort to wind down the adapter.
+	 */
+	if (time_after_eq(jiffies, ha->eeh_jif + ql2xdelay_before_pci_error_handling * HZ) &&
+	    !ha->flags.eeh_flush) {
+		ql_log(ql_log_info, vha, 0x9009,
+		    "PCI Error detected, attempting to reset hardware.\n");
+
+		ha->isp_ops->reset_chip(vha);
+		ha->isp_ops->disable_intrs(ha);
+
+		ha->flags.eeh_flush = EEH_FLUSH_RDY;
+		ha->eeh_jif = jiffies;
+
+	} else if (ha->flags.eeh_flush == EEH_FLUSH_RDY &&
+	    time_after_eq(jiffies, ha->eeh_jif +  5 * HZ)) {
+		pci_clear_master(ha->pdev);
+
+		/* flush all command */
+		qla2x00_abort_isp_cleanup(vha);
+		ha->flags.eeh_flush = EEH_FLUSH_DONE;
+
+		ql_log(ql_log_info, vha, 0x900a,
+		    "PCI Error handling complete, all IOs aborted.\n");
 	}
 }
 
@@ -7259,6 +7359,8 @@
 	fc_port_t *fcport = NULL;
 
 	if (ha->flags.eeh_busy) {
+		qla_wind_down_chip(vha);
+
 		ql_dbg(ql_dbg_timer, vha, 0x6000,
 		    "EEH = %d, restarting timer.\n",
 		    ha->flags.eeh_busy);
@@ -7354,7 +7456,7 @@
 
 		/* if the loop has been down for 4 minutes, reinit adapter */
 		if (atomic_dec_and_test(&vha->loop_down_timer) != 0) {
-			if (!(vha->device_flags & DFLG_NO_CABLE)) {
+			if (!(vha->device_flags & DFLG_NO_CABLE) && !vha->vp_idx) {
 				ql_log(ql_log_warn, vha, 0x6009,
 				    "Loop down - aborting ISP.\n");
 
@@ -7424,6 +7526,8 @@
 		start_dpc++;
 	}
 
+	/* borrowing w to signify dpc will run */
+	w = 0;
 	/* Schedule the DPC routine if needed */
 	if ((test_bit(ISP_ABORT_NEEDED, &vha->dpc_flags) ||
 	    test_bit(LOOP_RESYNC_NEEDED, &vha->dpc_flags) ||
@@ -7456,9 +7560,10 @@
 		    test_bit(RELOGIN_NEEDED, &vha->dpc_flags),
 		    test_bit(PROCESS_PUREX_IOCB, &vha->dpc_flags));
 		qla2xxx_wake_dpc(vha);
+		w = 1;
 	}
 
-	qla_heart_beat(vha);
+	qla_heart_beat(vha, w);
 
 	qla2x00_restart_timer(vha, WATCH_INTERVAL);
 }
@@ -7656,7 +7761,7 @@
 
 	switch (state) {
 	case pci_channel_io_normal:
-		ha->flags.eeh_busy = 0;
+		qla_pci_set_eeh_busy(vha);
 		if (ql2xmqsupport || ql2xnvmeenable) {
 			set_bit(QPAIR_ONLINE_CHECK_NEEDED, &vha->dpc_flags);
 			qla2xxx_wake_dpc(vha);
@@ -7697,9 +7802,16 @@
 	       "mmio enabled\n");
 
 	ha->pci_error_state = QLA_PCI_MMIO_ENABLED;
+
 	if (IS_QLA82XX(ha))
 		return PCI_ERS_RESULT_RECOVERED;
 
+	if (qla2x00_isp_reg_stat(ha)) {
+		ql_log(ql_log_info, base_vha, 0x803f,
+		    "During mmio enabled, PCI/Register disconnect still detected.\n");
+		goto out;
+	}
+
 	spin_lock_irqsave(&ha->hardware_lock, flags);
 	if (IS_QLA2100(ha) || IS_QLA2200(ha)){
 		stat = rd_reg_word(&reg->hccr);
@@ -7721,6 +7833,7 @@
 		    "RISC paused -- mmio_enabled, Dumping firmware.\n");
 		qla2xxx_dump_fw(base_vha);
 	}
+out:
 	/* set PCI_ERS_RESULT_NEED_RESET to trigger call to qla2xxx_pci_slot_reset */
 	ql_dbg(ql_dbg_aer, base_vha, 0x600d,
 	       "mmio enabled returning.\n");
@@ -7828,6 +7941,9 @@
 
 	spin_lock_irqsave(&base_vha->work_lock, flags);
 	if (!ha->flags.eeh_busy) {
+		ha->eeh_jif = jiffies;
+		ha->flags.eeh_flush = 0;
+
 		ha->flags.eeh_busy = 1;
 		do_cleanup = true;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_sup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_sup.c
@@ -555,6 +555,7 @@
 	struct qla_flt_location *fltl = (void *)req->ring;
 	uint32_t *dcode = (uint32_t *)req->ring;
 	uint8_t *buf = (void *)req->ring, *bcode,  last_image;
+	int rc;
 
 	/*
 	 * FLT-location structure resides after the last PCI region.
@@ -584,14 +585,24 @@
 	pcihdr = 0;
 	do {
 		/* Verify PCI expansion ROM header. */
-		qla24xx_read_flash_data(vha, dcode, pcihdr >> 2, 0x20);
+		rc = qla24xx_read_flash_data(vha, dcode, pcihdr >> 2, 0x20);
+		if (rc) {
+			ql_log(ql_log_info, vha, 0x016d,
+			    "Unable to read PCI Expansion Rom Header (%x).\n", rc);
+			return QLA_FUNCTION_FAILED;
+		}
 		bcode = buf + (pcihdr % 4);
 		if (bcode[0x0] != 0x55 || bcode[0x1] != 0xaa)
 			goto end;
 
 		/* Locate PCI data structure. */
 		pcids = pcihdr + ((bcode[0x19] << 8) | bcode[0x18]);
-		qla24xx_read_flash_data(vha, dcode, pcids >> 2, 0x20);
+		rc = qla24xx_read_flash_data(vha, dcode, pcids >> 2, 0x20);
+		if (rc) {
+			ql_log(ql_log_info, vha, 0x0179,
+			    "Unable to read PCI Data Structure (%x).\n", rc);
+			return QLA_FUNCTION_FAILED;
+		}
 		bcode = buf + (pcihdr % 4);
 
 		/* Validate signature of PCI data structure. */
@@ -606,7 +617,12 @@
 	} while (!last_image);
 
 	/* Now verify FLT-location structure. */
-	qla24xx_read_flash_data(vha, dcode, pcihdr >> 2, sizeof(*fltl) >> 2);
+	rc = qla24xx_read_flash_data(vha, dcode, pcihdr >> 2, sizeof(*fltl) >> 2);
+	if (rc) {
+		ql_log(ql_log_info, vha, 0x017a,
+		    "Unable to read FLT (%x).\n", rc);
+		return QLA_FUNCTION_FAILED;
+	}
 	if (memcmp(fltl->sig, "QFLT", 4))
 		goto end;
 
@@ -844,7 +860,7 @@
 				ha->flt_region_nvram = start;
 			break;
 		case FLT_REG_IMG_PRI_27XX:
-			if (IS_QLA27XX(ha) && !IS_QLA28XX(ha))
+			if (IS_QLA27XX(ha) || IS_QLA28XX(ha))
 				ha->flt_region_img_status_pri = start;
 			break;
 		case FLT_REG_IMG_SEC_27XX:
@@ -1356,7 +1372,7 @@
 		    flash_data_addr(ha, faddr), le32_to_cpu(*dwptr));
 		if (ret) {
 			ql_dbg(ql_dbg_user, vha, 0x7006,
-			    "Failed slopw write %x (%x)\n", faddr, *dwptr);
+			    "Failed slow write %x (%x)\n", faddr, *dwptr);
 			break;
 		}
 	}
@@ -2605,13 +2621,18 @@
     uint32_t offset, uint32_t length)
 {
 	struct qla_hw_data *ha = vha->hw;
+	int rc;
 
 	/* Suspend HBA. */
 	scsi_block_requests(vha->host);
 	set_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
 
 	/* Go with read. */
-	qla24xx_read_flash_data(vha, buf, offset >> 2, length >> 2);
+	rc = qla24xx_read_flash_data(vha, buf, offset >> 2, length >> 2);
+	if (rc) {
+		ql_log(ql_log_info, vha, 0x01a0,
+		    "Unable to perform optrom read(%x).\n", rc);
+	}
 
 	/* Resume HBA. */
 	clear_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
@@ -3412,7 +3433,7 @@
 	struct active_regions active_regions = { };
 
 	if (IS_P3P_TYPE(ha))
-		return ret;
+		return QLA_SUCCESS;
 
 	if (!mbuf)
 		return QLA_FUNCTION_FAILED;
@@ -3432,20 +3453,31 @@
 
 	do {
 		/* Verify PCI expansion ROM header. */
-		qla24xx_read_flash_data(vha, dcode, pcihdr >> 2, 0x20);
+		ret = qla24xx_read_flash_data(vha, dcode, pcihdr >> 2, 0x20);
+		if (ret) {
+			ql_log(ql_log_info, vha, 0x017d,
+			    "Unable to read PCI EXP Rom Header(%x).\n", ret);
+			return QLA_FUNCTION_FAILED;
+		}
+
 		bcode = mbuf + (pcihdr % 4);
 		if (memcmp(bcode, "\x55\xaa", 2)) {
 			/* No signature */
 			ql_log(ql_log_fatal, vha, 0x0059,
 			    "No matching ROM signature.\n");
-			ret = QLA_FUNCTION_FAILED;
-			break;
+			return QLA_FUNCTION_FAILED;
 		}
 
 		/* Locate PCI data structure. */
 		pcids = pcihdr + ((bcode[0x19] << 8) | bcode[0x18]);
 
-		qla24xx_read_flash_data(vha, dcode, pcids >> 2, 0x20);
+		ret = qla24xx_read_flash_data(vha, dcode, pcids >> 2, 0x20);
+		if (ret) {
+			ql_log(ql_log_info, vha, 0x018e,
+			    "Unable to read PCI Data Structure (%x).\n", ret);
+			return QLA_FUNCTION_FAILED;
+		}
+
 		bcode = mbuf + (pcihdr % 4);
 
 		/* Validate signature of PCI data structure. */
@@ -3454,8 +3486,7 @@
 			ql_log(ql_log_fatal, vha, 0x005a,
 			    "PCI data struct not found pcir_adr=%x.\n", pcids);
 			ql_dump_buffer(ql_dbg_init, vha, 0x0059, dcode, 32);
-			ret = QLA_FUNCTION_FAILED;
-			break;
+			return QLA_FUNCTION_FAILED;
 		}
 
 		/* Read version */
@@ -3507,20 +3538,26 @@
 			faddr = ha->flt_region_fw_sec;
 	}
 
-	qla24xx_read_flash_data(vha, dcode, faddr, 8);
-	if (qla24xx_risc_firmware_invalid(dcode)) {
-		ql_log(ql_log_warn, vha, 0x005f,
-		    "Unrecognized fw revision at %x.\n",
-		    ha->flt_region_fw * 4);
-		ql_dump_buffer(ql_dbg_init, vha, 0x005f, dcode, 32);
+	ret = qla24xx_read_flash_data(vha, dcode, faddr, 8);
+	if (ret) {
+		ql_log(ql_log_info, vha, 0x019e,
+		    "Unable to read FW version (%x).\n", ret);
+		return ret;
 	} else {
-		for (i = 0; i < 4; i++)
-			ha->fw_revision[i] =
+		if (qla24xx_risc_firmware_invalid(dcode)) {
+			ql_log(ql_log_warn, vha, 0x005f,
+			    "Unrecognized fw revision at %x.\n",
+			    ha->flt_region_fw * 4);
+			ql_dump_buffer(ql_dbg_init, vha, 0x005f, dcode, 32);
+		} else {
+			for (i = 0; i < 4; i++)
+				ha->fw_revision[i] =
 				be32_to_cpu((__force __be32)dcode[4+i]);
-		ql_dbg(ql_dbg_init, vha, 0x0060,
-		    "Firmware revision (flash) %u.%u.%u (%x).\n",
-		    ha->fw_revision[0], ha->fw_revision[1],
-		    ha->fw_revision[2], ha->fw_revision[3]);
+			ql_dbg(ql_dbg_init, vha, 0x0060,
+			    "Firmware revision (flash) %u.%u.%u (%x).\n",
+			    ha->fw_revision[0], ha->fw_revision[1],
+			    ha->fw_revision[2], ha->fw_revision[3]);
+		}
 	}
 
 	/* Check for golden firmware and get version if available */
@@ -3531,18 +3568,23 @@
 
 	memset(ha->gold_fw_version, 0, sizeof(ha->gold_fw_version));
 	faddr = ha->flt_region_gold_fw;
-	qla24xx_read_flash_data(vha, dcode, ha->flt_region_gold_fw, 8);
-	if (qla24xx_risc_firmware_invalid(dcode)) {
-		ql_log(ql_log_warn, vha, 0x0056,
-		    "Unrecognized golden fw at %#x.\n", faddr);
-		ql_dump_buffer(ql_dbg_init, vha, 0x0056, dcode, 32);
+	ret = qla24xx_read_flash_data(vha, dcode, ha->flt_region_gold_fw, 8);
+	if (ret) {
+		ql_log(ql_log_info, vha, 0x019f,
+		    "Unable to read Gold FW version (%x).\n", ret);
 		return ret;
-	}
-
-	for (i = 0; i < 4; i++)
-		ha->gold_fw_version[i] =
-			be32_to_cpu((__force __be32)dcode[4+i]);
+	} else {
+		if (qla24xx_risc_firmware_invalid(dcode)) {
+			ql_log(ql_log_warn, vha, 0x0056,
+			    "Unrecognized golden fw at %#x.\n", faddr);
+			ql_dump_buffer(ql_dbg_init, vha, 0x0056, dcode, 32);
+			return QLA_FUNCTION_FAILED;
+		}
 
+		for (i = 0; i < 4; i++)
+			ha->gold_fw_version[i] =
+			   be32_to_cpu((__force __be32)dcode[4+i]);
+	}
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_target.c
@@ -620,7 +620,7 @@
 	}
 	spin_unlock_irqrestore(&vha->hw->tgt.sess_lock, flags);
 
-	sp->free(sp);
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 }
 
 int qla24xx_async_notify_ack(scsi_qla_host_t *vha, fc_port_t *fcport,
@@ -656,12 +656,10 @@
 
 	sp->type = type;
 	sp->name = "nack";
-
-	sp->u.iocb_cmd.timeout = qla2x00_async_iocb_timeout;
-	qla2x00_init_timer(sp, qla2x00_get_async_timeout(vha)+2);
+	qla2x00_init_async_sp(sp, qla2x00_get_async_timeout(vha) + 2,
+			      qla2x00_async_nack_sp_done);
 
 	sp->u.iocb_cmd.u.nack.ntfy = ntfy;
-	sp->done = qla2x00_async_nack_sp_done;
 
 	ql_dbg(ql_dbg_disc, vha, 0x20f4,
 	    "Async-%s %8phC hndl %x %s\n",
@@ -674,7 +672,7 @@
 	return rval;
 
 done_free_sp:
-	sp->free(sp);
+	kref_put(&sp->cmd_kref, qla2x00_sp_release);
 done:
 	fcport->flags &= ~FCF_ASYNC_SENT;
 	return rval;
@@ -1003,6 +1001,7 @@
 					"%s bypassing release_all_sadb\n",
 					__func__);
 			}
+			qla_edif_clear_appdata(vha, sess);
 			qla_edif_sess_down(vha, sess);
 		}
 		qla2x00_mark_device_lost(vha, sess, 0);
@@ -1084,16 +1083,22 @@
 		    "%s: sess %p logout completed\n", __func__, sess);
 	}
 
+	/* check for any straggling io left behind */
+	if (!(sess->flags & FCF_FCP2_DEVICE) &&
+	    qla2x00_eh_wait_for_pending_commands(sess->vha, sess->d_id.b24, 0, WAIT_TARGET)) {
+		ql_log(ql_log_warn, vha, 0x3027,
+		    "IO not return. Resetting.\n");
+		set_bit(ISP_ABORT_NEEDED, &vha->dpc_flags);
+		qla2xxx_wake_dpc(vha);
+		qla2x00_wait_for_chip_reset(vha);
+	}
+
 	if (sess->logo_ack_needed) {
 		sess->logo_ack_needed = 0;
 		qla24xx_async_notify_ack(vha, sess,
 			(struct imm_ntfy_from_isp *)sess->iocb, SRB_NACK_LOGO);
 	}
 
-	spin_lock_irqsave(&vha->work_lock, flags);
-	sess->flags &= ~FCF_ASYNC_SENT;
-	spin_unlock_irqrestore(&vha->work_lock, flags);
-
 	spin_lock_irqsave(&ha->tgt.sess_lock, flags);
 	if (sess->se_sess) {
 		sess->se_sess = NULL;
@@ -1103,7 +1108,6 @@
 
 	qla2x00_set_fcport_disc_state(sess, DSC_DELETED);
 	sess->fw_login_state = DSC_LS_PORT_UNAVAIL;
-	sess->deleted = QLA_SESS_DELETED;
 
 	if (sess->login_succ && !IS_SW_RESV_ADDR(sess->d_id)) {
 		vha->fcport_count--;
@@ -1155,10 +1159,15 @@
 
 	sess->explicit_logout = 0;
 	spin_unlock_irqrestore(&ha->tgt.sess_lock, flags);
-	sess->free_pending = 0;
 
 	qla2x00_dfs_remove_rport(vha, sess);
 
+	spin_lock_irqsave(&vha->work_lock, flags);
+	sess->flags &= ~FCF_ASYNC_SENT;
+	sess->deleted = QLA_SESS_DELETED;
+	sess->free_pending = 0;
+	spin_unlock_irqrestore(&vha->work_lock, flags);
+
 	ql_dbg(ql_dbg_disc, vha, 0xf001,
 	    "Unregistration of sess %p %8phC finished fcp_cnt %d\n",
 		sess, sess->port_name, vha->fcport_count);
@@ -1207,12 +1216,12 @@
 	 * management from being sent.
 	 */
 	sess->flags |= FCF_ASYNC_SENT;
+	sess->deleted = QLA_SESS_DELETION_IN_PROGRESS;
 	spin_unlock_irqrestore(&sess->vha->work_lock, flags);
 
 	if (sess->se_sess)
 		vha->hw->tgt.tgt_ops->clear_nacl_from_fcport_map(sess);
 
-	sess->deleted = QLA_SESS_DELETION_IN_PROGRESS;
 	qla2x00_set_fcport_disc_state(sess, DSC_DELETE_PEND);
 	sess->last_rscn_gen = sess->rscn_gen;
 	sess->last_login_gen = sess->login_gen;
@@ -2167,8 +2176,10 @@
 
 	abort_cmd = ha->tgt.tgt_ops->find_cmd_by_tag(sess,
 				le32_to_cpu(abts->exchange_addr_to_abort));
-	if (!abort_cmd)
+	if (!abort_cmd) {
+		mempool_free(mcmd, qla_tgt_mgmt_cmd_mempool);
 		return -EIO;
+	}
 	mcmd->unpacked_lun = abort_cmd->se_cmd.orig_fe_lun;
 
 	if (abort_cmd->qpair) {
@@ -3319,6 +3330,7 @@
 			"RESET-RSP online/active/old-count/new-count = %d/%d/%d/%d.\n",
 			vha->flags.online, qla2x00_reset_active(vha),
 			cmd->reset_count, qpair->chip_reset);
+		res = 0;
 		goto out_unmap_unlock;
 	}
 
@@ -3837,6 +3849,9 @@
 
 	spin_lock_irqsave(&cmd->cmd_lock, flags);
 	if (cmd->aborted) {
+		if (cmd->sg_mapped)
+			qlt_unmap_sg(vha, cmd);
+
 		spin_unlock_irqrestore(&cmd->cmd_lock, flags);
 		/*
 		 * It's normal to see 2 calls in this path:
@@ -4454,8 +4469,7 @@
 		queue_work_on(cmd->se_cmd.cpuid, qla_tgt_wq, &cmd->work);
 	} else if (ha->msix_count) {
 		if (cmd->atio.u.isp24.fcp_cmnd.rddata)
-			queue_work_on(smp_processor_id(), qla_tgt_wq,
-			    &cmd->work);
+			queue_work(qla_tgt_wq, &cmd->work);
 		else
 			queue_work_on(cmd->se_cmd.cpuid, qla_tgt_wq,
 			    &cmd->work);
@@ -4812,7 +4826,7 @@
 	}
 
 	if (vha->hw->flags.edif_enabled) {
-		if (!(vha->e_dbell.db_flags & EDB_ACTIVE)) {
+		if (DBELL_INACTIVE(vha)) {
 			ql_dbg(ql_dbg_disc, vha, 0xffff,
 			       "%s %d Term INOT due to app not started lid=%d, NportID %06X ",
 			       __func__, __LINE__, loop_id, port_id.b24);
@@ -6958,14 +6972,8 @@
 
 	if (ha->flags.msix_enabled) {
 		if (IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha)) {
-			if (IS_QLA2071(ha)) {
-				/* 4 ports Baker: Enable Interrupt Handshake */
-				icb->msix_atio = 0;
-				icb->firmware_options_2 |= cpu_to_le32(BIT_26);
-			} else {
-				icb->msix_atio = cpu_to_le16(msix->entry);
-				icb->firmware_options_2 &= cpu_to_le32(~BIT_26);
-			}
+			icb->msix_atio = cpu_to_le16(msix->entry);
+			icb->firmware_options_2 &= cpu_to_le32(~BIT_26);
 			ql_dbg(ql_dbg_init, vha, 0xf072,
 			    "Registering ICB vector 0x%x for atio que.\n",
 			    msix->entry);
@@ -7220,8 +7228,7 @@
 	if (!QLA_TGT_MODE_ENABLED())
 		return;
 
-	if  ((ql2xenablemsix == 0) || IS_QLA83XX(ha) || IS_QLA27XX(ha) ||
-	    IS_QLA28XX(ha)) {
+	if  (ha->mqenable || IS_QLA83XX(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha)) {
 		ISP_ATIO_Q_IN(base_vha) = &ha->mqiobase->isp25mq.atio_q_in;
 		ISP_ATIO_Q_OUT(base_vha) = &ha->mqiobase->isp25mq.atio_q_out;
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_target.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_target.h
@@ -1080,8 +1080,6 @@
 	struct init_cb_81xx *);
 extern void qlt_81xx_config_nvram_stage1(struct scsi_qla_host *,
 	struct nvram_81xx *);
-extern int qlt_24xx_process_response_error(struct scsi_qla_host *,
-	struct sts_entry_24xx *);
 extern void qlt_modify_vp_config(struct scsi_qla_host *,
 	struct vp_config_entry_24xx *);
 extern void qlt_probe_one_stage1(struct scsi_qla_host *, struct qla_hw_data *);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/qla_tmpl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/qla_tmpl.c
@@ -435,8 +435,13 @@
 {
 	ql_dbg(ql_dbg_misc, vha, 0xd20a,
 	    "%s: reset risc [%lx]\n", __func__, *len);
-	if (buf)
-		WARN_ON_ONCE(qla24xx_soft_reset(vha->hw) != QLA_SUCCESS);
+	if (buf) {
+		if (qla24xx_soft_reset(vha->hw) != QLA_SUCCESS) {
+			ql_dbg(ql_dbg_async, vha, 0x5001,
+			    "%s: unable to soft reset\n", __func__);
+			return INVALID_ENTRY;
+		}
+	}
 
 	return qla27xx_next_entry(ent);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla2xxx/tcm_qla2xxx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla2xxx/tcm_qla2xxx.c
@@ -310,7 +310,7 @@
 	cmd->trc_flags |= TRC_CMD_DONE;
 
 	INIT_WORK(&cmd->work, tcm_qla2xxx_complete_free);
-	queue_work_on(smp_processor_id(), tcm_qla2xxx_free_wq, &cmd->work);
+	queue_work(tcm_qla2xxx_free_wq, &cmd->work);
 }
 
 /*
@@ -557,7 +557,7 @@
 	cmd->trc_flags |= TRC_DATA_IN;
 	cmd->cmd_in_wq = 1;
 	INIT_WORK(&cmd->work, tcm_qla2xxx_handle_data_work);
-	queue_work_on(smp_processor_id(), tcm_qla2xxx_free_wq, &cmd->work);
+	queue_work(tcm_qla2xxx_free_wq, &cmd->work);
 }
 
 static int tcm_qla2xxx_chk_dif_tags(uint32_t tag)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/qla4xxx/ql4_os.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/qla4xxx/ql4_os.c
@@ -968,6 +968,11 @@
 	memset(&chap_rec, 0, sizeof(chap_rec));
 
 	nla_for_each_attr(attr, data, len, rem) {
+		if (nla_len(attr) < sizeof(*param_info)) {
+			rc = -EINVAL;
+			goto exit_set_chap;
+		}
+
 		param_info = nla_data(attr);
 
 		switch (param_info->param) {
@@ -2750,6 +2755,11 @@
 	}
 
 	nla_for_each_attr(attr, data, len, rem) {
+		if (nla_len(attr) < sizeof(*iface_param)) {
+			rval = -EINVAL;
+			goto exit_init_fw_cb;
+		}
+
 		iface_param = nla_data(attr);
 
 		if (iface_param->param_type == ISCSI_NET_PARAM) {
@@ -8105,6 +8115,11 @@
 
 	memset((void *)&chap_tbl, 0, sizeof(chap_tbl));
 	nla_for_each_attr(attr, data, len, rem) {
+		if (nla_len(attr) < sizeof(*fnode_param)) {
+			rc = -EINVAL;
+			goto exit_set_param;
+		}
+
 		fnode_param = nla_data(attr);
 
 		switch (fnode_param->param) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/raid_class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/raid_class.c
@@ -209,53 +209,6 @@
 raid_attr_ro_fn(resync);
 raid_attr_ro_state_fn(state);
 
-static void raid_component_release(struct device *dev)
-{
-	struct raid_component *rc =
-		container_of(dev, struct raid_component, dev);
-	dev_printk(KERN_ERR, rc->dev.parent, "COMPONENT RELEASE\n");
-	put_device(rc->dev.parent);
-	kfree(rc);
-}
-
-int raid_component_add(struct raid_template *r,struct device *raid_dev,
-		       struct device *component_dev)
-{
-	struct device *cdev =
-		attribute_container_find_class_device(&r->raid_attrs.ac,
-						      raid_dev);
-	struct raid_component *rc;
-	struct raid_data *rd = dev_get_drvdata(cdev);
-	int err;
-
-	rc = kzalloc(sizeof(*rc), GFP_KERNEL);
-	if (!rc)
-		return -ENOMEM;
-
-	INIT_LIST_HEAD(&rc->node);
-	device_initialize(&rc->dev);
-	rc->dev.release = raid_component_release;
-	rc->dev.parent = get_device(component_dev);
-	rc->num = rd->component_count++;
-
-	dev_set_name(&rc->dev, "component-%d", rc->num);
-	list_add_tail(&rc->node, &rd->component_list);
-	rc->dev.class = &raid_class.class;
-	err = device_add(&rc->dev);
-	if (err)
-		goto err_out;
-
-	return 0;
-
-err_out:
-	list_del(&rc->node);
-	rd->component_count--;
-	put_device(component_dev);
-	kfree(rc);
-	return err;
-}
-EXPORT_SYMBOL(raid_component_add);
-
 struct raid_template *
 raid_class_attach(struct raid_function_template *ft)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi.c
@@ -209,11 +209,11 @@
 
 
 /*
- * 1024 is big enough for saturating the fast scsi LUN now
+ * 1024 is big enough for saturating fast SCSI LUNs.
  */
 int scsi_device_max_queue_depth(struct scsi_device *sdev)
 {
-	return max_t(int, sdev->host->can_queue, 1024);
+	return min_t(int, sdev->host->can_queue, 1024);
 }
 
 /**
@@ -323,11 +323,18 @@
 	if (result)
 		return -EIO;
 
-	/* Sanity check that we got the page back that we asked for */
+	/*
+	 * Sanity check that we got the page back that we asked for and that
+	 * the page size is not 0.
+	 */
 	if (buffer[1] != page)
 		return -EIO;
 
-	return get_unaligned_be16(&buffer[2]) + 4;
+	result = get_unaligned_be16(&buffer[2]);
+	if (!result)
+		return -EIO;
+
+	return result + 4;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_debug.c
@@ -1189,7 +1189,7 @@
 		 __func__, off_dst, scsi_bufflen(scp), act_len,
 		 scsi_get_resid(scp));
 	n = scsi_bufflen(scp) - (off_dst + act_len);
-	scsi_set_resid(scp, min_t(int, scsi_get_resid(scp), n));
+	scsi_set_resid(scp, min_t(u32, scsi_get_resid(scp), n));
 	return 0;
 }
 
@@ -1562,7 +1562,8 @@
 	unsigned char pq_pdt;
 	unsigned char *arr;
 	unsigned char *cmd = scp->cmnd;
-	int alloc_len, n, ret;
+	u32 alloc_len, n;
+	int ret;
 	bool have_wlun, is_disk, is_zbc, is_disk_zbc;
 
 	alloc_len = get_unaligned_be16(cmd + 3);
@@ -1585,7 +1586,8 @@
 		kfree(arr);
 		return check_condition_result;
 	} else if (0x1 & cmd[1]) {  /* EVPD bit set */
-		int lu_id_num, port_group_id, target_dev_id, len;
+		int lu_id_num, port_group_id, target_dev_id;
+		u32 len;
 		char lu_id_str[6];
 		int host_no = devip->sdbg_host->shost->host_no;
 		
@@ -1676,9 +1678,9 @@
 			kfree(arr);
 			return check_condition_result;
 		}
-		len = min(get_unaligned_be16(arr + 2) + 4, alloc_len);
+		len = min_t(u32, get_unaligned_be16(arr + 2) + 4, alloc_len);
 		ret = fill_from_dev_buffer(scp, arr,
-			    min(len, SDEBUG_MAX_INQ_ARR_SZ));
+			    min_t(u32, len, SDEBUG_MAX_INQ_ARR_SZ));
 		kfree(arr);
 		return ret;
 	}
@@ -1714,7 +1716,7 @@
 	}
 	put_unaligned_be16(0x2100, arr + n);	/* SPL-4 no version claimed */
 	ret = fill_from_dev_buffer(scp, arr,
-			    min_t(int, alloc_len, SDEBUG_LONG_INQ_SZ));
+			    min_t(u32, alloc_len, SDEBUG_LONG_INQ_SZ));
 	kfree(arr);
 	return ret;
 }
@@ -1729,8 +1731,8 @@
 	unsigned char *cmd = scp->cmnd;
 	unsigned char arr[SCSI_SENSE_BUFFERSIZE];	/* assume >= 18 bytes */
 	bool dsense = !!(cmd[1] & 1);
-	int alloc_len = cmd[4];
-	int len = 18;
+	u32 alloc_len = cmd[4];
+	u32 len = 18;
 	int stopped_state = atomic_read(&devip->stopped);
 
 	memset(arr, 0, sizeof(arr));
@@ -1774,7 +1776,7 @@
 			arr[7] = 0xa;
 		}
 	}
-	return fill_from_dev_buffer(scp, arr, min_t(int, len, alloc_len));
+	return fill_from_dev_buffer(scp, arr, min_t(u32, len, alloc_len));
 }
 
 static int resp_start_stop(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
@@ -1856,7 +1858,7 @@
 {
 	unsigned char *cmd = scp->cmnd;
 	unsigned char arr[SDEBUG_READCAP16_ARR_SZ];
-	int alloc_len;
+	u32 alloc_len;
 
 	alloc_len = get_unaligned_be32(cmd + 10);
 	/* following just in case virtual_gb changed */
@@ -1877,6 +1879,13 @@
 			arr[14] |= 0x40;
 	}
 
+	/*
+	 * Since the scsi_debug READ CAPACITY implementation always reports the
+	 * total disk capacity, set RC BASIS = 1 for host-managed ZBC devices.
+	 */
+	if (devip->zmodel == BLK_ZONED_HM)
+		arr[12] |= 1 << 4;
+
 	arr[15] = sdebug_lowest_aligned & 0xff;
 
 	if (have_dif_prot) {
@@ -1885,7 +1894,7 @@
 	}
 
 	return fill_from_dev_buffer(scp, arr,
-			    min_t(int, alloc_len, SDEBUG_READCAP16_ARR_SZ));
+			    min_t(u32, alloc_len, SDEBUG_READCAP16_ARR_SZ));
 }
 
 #define SDEBUG_MAX_TGTPGS_ARR_SZ 1412
@@ -1896,8 +1905,9 @@
 	unsigned char *cmd = scp->cmnd;
 	unsigned char *arr;
 	int host_no = devip->sdbg_host->shost->host_no;
-	int n, ret, alen, rlen;
 	int port_group_a, port_group_b, port_a, port_b;
+	u32 alen, n, rlen;
+	int ret;
 
 	alen = get_unaligned_be32(cmd + 6);
 	arr = kzalloc(SDEBUG_MAX_TGTPGS_ARR_SZ, GFP_ATOMIC);
@@ -1959,9 +1969,9 @@
 	 * - The constructed command length
 	 * - The maximum array size
 	 */
-	rlen = min_t(int, alen, n);
+	rlen = min(alen, n);
 	ret = fill_from_dev_buffer(scp, arr,
-			   min_t(int, rlen, SDEBUG_MAX_TGTPGS_ARR_SZ));
+			   min_t(u32, rlen, SDEBUG_MAX_TGTPGS_ARR_SZ));
 	kfree(arr);
 	return ret;
 }
@@ -2311,7 +2321,8 @@
 {
 	int pcontrol, pcode, subpcode, bd_len;
 	unsigned char dev_spec;
-	int alloc_len, offset, len, target_dev_id;
+	u32 alloc_len, offset, len;
+	int target_dev_id;
 	int target = scp->device->id;
 	unsigned char *ap;
 	unsigned char arr[SDEBUG_MAX_MSENSE_SZ];
@@ -2467,7 +2478,7 @@
 		arr[0] = offset - 1;
 	else
 		put_unaligned_be16((offset - 2), arr + 0);
-	return fill_from_dev_buffer(scp, arr, min_t(int, alloc_len, offset));
+	return fill_from_dev_buffer(scp, arr, min_t(u32, alloc_len, offset));
 }
 
 #define SDEBUG_MAX_MSELECT_SZ 512
@@ -2498,11 +2509,11 @@
 			    __func__, param_len, res);
 	md_len = mselect6 ? (arr[0] + 1) : (get_unaligned_be16(arr + 0) + 2);
 	bd_len = mselect6 ? arr[3] : get_unaligned_be16(arr + 6);
-	if (md_len > 2) {
+	off = bd_len + (mselect6 ? 4 : 8);
+	if (md_len > 2 || off >= res) {
 		mk_sense_invalid_fld(scp, SDEB_IN_DATA, 0, -1);
 		return check_condition_result;
 	}
-	off = bd_len + (mselect6 ? 4 : 8);
 	mpage = arr[off] & 0x3f;
 	ps = !!(arr[off] & 0x80);
 	if (ps) {
@@ -2582,7 +2593,8 @@
 static int resp_log_sense(struct scsi_cmnd *scp,
 			  struct sdebug_dev_info *devip)
 {
-	int ppc, sp, pcode, subpcode, alloc_len, len, n;
+	int ppc, sp, pcode, subpcode;
+	u32 alloc_len, len, n;
 	unsigned char arr[SDEBUG_MAX_LSENSE_SZ];
 	unsigned char *cmd = scp->cmnd;
 
@@ -2652,9 +2664,9 @@
 		mk_sense_invalid_fld(scp, SDEB_IN_CDB, 3, -1);
 		return check_condition_result;
 	}
-	len = min_t(int, get_unaligned_be16(arr + 2) + 4, alloc_len);
+	len = min_t(u32, get_unaligned_be16(arr + 2) + 4, alloc_len);
 	return fill_from_dev_buffer(scp, arr,
-		    min_t(int, len, SDEBUG_MAX_INQ_ARR_SZ));
+		    min_t(u32, len, SDEBUG_MAX_INQ_ARR_SZ));
 }
 
 static inline bool sdebug_dev_is_zoned(struct sdebug_dev_info *devip)
@@ -2742,6 +2754,24 @@
 	}
 }
 
+static inline void zbc_set_zone_full(struct sdebug_dev_info *devip,
+				     struct sdeb_zone_state *zsp)
+{
+	switch (zsp->z_cond) {
+	case ZC2_IMPLICIT_OPEN:
+		devip->nr_imp_open--;
+		break;
+	case ZC3_EXPLICIT_OPEN:
+		devip->nr_exp_open--;
+		break;
+	default:
+		WARN_ONCE(true, "Invalid zone %llu condition %x\n",
+			  zsp->z_start, zsp->z_cond);
+		break;
+	}
+	zsp->z_cond = ZC5_FULL;
+}
+
 static void zbc_inc_wp(struct sdebug_dev_info *devip,
 		       unsigned long long lba, unsigned int num)
 {
@@ -2754,7 +2784,7 @@
 	if (zsp->z_type == ZBC_ZONE_TYPE_SWR) {
 		zsp->z_wp += num;
 		if (zsp->z_wp >= zend)
-			zsp->z_cond = ZC5_FULL;
+			zbc_set_zone_full(devip, zsp);
 		return;
 	}
 
@@ -2773,7 +2803,7 @@
 			n = num;
 		}
 		if (zsp->z_wp >= zend)
-			zsp->z_cond = ZC5_FULL;
+			zbc_set_zone_full(devip, zsp);
 
 		num -= n;
 		lba += n;
@@ -3610,7 +3640,7 @@
 		mk_sense_buffer(scp, ILLEGAL_REQUEST, INVALID_FIELD_IN_CDB, 0);
 		return illegal_condition_result;
 	}
-	lrdp = kzalloc(lbdof_blen, GFP_ATOMIC);
+	lrdp = kzalloc(lbdof_blen, GFP_ATOMIC | __GFP_NOWARN);
 	if (lrdp == NULL)
 		return SCSI_MLQUEUE_HOST_BUSY;
 	if (sdebug_verbose)
@@ -4258,13 +4288,15 @@
 		mk_sense_invalid_opcode(scp);
 		return check_condition_result;
 	}
+	if (vnum == 0)
+		return 0;	/* not an error */
 	a_num = is_bytchk3 ? 1 : vnum;
 	/* Treat following check like one for read (i.e. no write) access */
 	ret = check_device_access_params(scp, lba, a_num, false);
 	if (ret)
 		return ret;
 
-	arr = kcalloc(lb_size, vnum, GFP_ATOMIC);
+	arr = kcalloc(lb_size, vnum, GFP_ATOMIC | __GFP_NOWARN);
 	if (!arr) {
 		mk_sense_buffer(scp, ILLEGAL_REQUEST, INSUFF_RES_ASC,
 				INSUFF_RES_ASCQ);
@@ -4321,6 +4353,8 @@
 	}
 	zs_lba = get_unaligned_be64(cmd + 2);
 	alloc_len = get_unaligned_be32(cmd + 10);
+	if (alloc_len == 0)
+		return 0;	/* not an error */
 	rep_opts = cmd[14] & 0x3f;
 	partial = cmd[14] & 0x80;
 
@@ -4333,7 +4367,7 @@
 	rep_max_zones = min((alloc_len - 64) >> ilog2(RZONES_DESC_HD),
 			    max_zones);
 
-	arr = kcalloc(RZONES_DESC_HD, alloc_len, GFP_ATOMIC);
+	arr = kzalloc(alloc_len, GFP_ATOMIC | __GFP_NOWARN);
 	if (!arr) {
 		mk_sense_buffer(scp, ILLEGAL_REQUEST, INSUFF_RES_ASC,
 				INSUFF_RES_ASCQ);
@@ -4425,7 +4459,7 @@
 	put_unaligned_be64(sdebug_capacity - 1, arr + 8);
 
 	rep_len = (unsigned long)desc - (unsigned long)arr;
-	ret = fill_from_dev_buffer(scp, arr, min_t(int, alloc_len, rep_len));
+	ret = fill_from_dev_buffer(scp, arr, min_t(u32, alloc_len, rep_len));
 
 fini:
 	read_unlock(macc_lckp);
@@ -4648,6 +4682,7 @@
 			 struct sdeb_zone_state *zsp)
 {
 	enum sdebug_z_cond zc;
+	struct sdeb_store_info *sip = devip2sip(devip, false);
 
 	if (zbc_zone_is_conv(zsp))
 		return;
@@ -4659,6 +4694,10 @@
 	if (zsp->z_cond == ZC4_CLOSED)
 		devip->nr_closed--;
 
+	if (zsp->z_wp > zsp->z_start)
+		memset(sip->storep + zsp->z_start * sdebug_sector_size, 0,
+		       (zsp->z_wp - zsp->z_start) * sdebug_sector_size);
+
 	zsp->z_non_seq_resource = false;
 	zsp->z_wp = zsp->z_start;
 	zsp->z_cond = ZC1_EMPTY;
@@ -7100,8 +7139,12 @@
 	dev_set_name(&sdbg_host->dev, "adapter%d", sdebug_num_hosts);
 
 	error = device_register(&sdbg_host->dev);
-	if (error)
+	if (error) {
+		spin_lock(&sdebug_host_list_lock);
+		list_del(&sdbg_host->host_list);
+		spin_unlock(&sdebug_host_list_lock);
 		goto clean;
+	}
 
 	++sdebug_num_hosts;
 	return 0;
@@ -7113,7 +7156,10 @@
 		kfree(sdbg_devinfo->zstate);
 		kfree(sdbg_devinfo);
 	}
-	kfree(sdbg_host);
+	if (sdbg_host->dev.release)
+		put_device(&sdbg_host->dev);
+	else
+		kfree(sdbg_host);
 	pr_warn("%s: failed, errno=%d\n", __func__, -error);
 	return error;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_debugfs.c
@@ -9,6 +9,7 @@
 static const char *const scsi_cmd_flags[] = {
 	SCSI_CMD_FLAG_NAME(TAGGED),
 	SCSI_CMD_FLAG_NAME(INITIALIZED),
+	SCSI_CMD_FLAG_NAME(LAST),
 };
 #undef SCSI_CMD_FLAG_NAME
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_devinfo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_devinfo.c
@@ -233,6 +233,7 @@
 	{"SGI", "RAID5", "*", BLIST_SPARSELUN},
 	{"SGI", "TP9100", "*", BLIST_REPORTLUN2},
 	{"SGI", "Universal Xport", "*", BLIST_NO_ULD_ATTACH},
+	{"SKhynix", "H28U74301AMR", NULL, BLIST_SKIP_VPD_PAGES},
 	{"IBM", "Universal Xport", "*", BLIST_NO_ULD_ATTACH},
 	{"SUN", "Universal Xport", "*", BLIST_NO_ULD_ATTACH},
 	{"DELL", "Universal Xport", "*", BLIST_NO_ULD_ATTACH},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_error.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_error.c
@@ -50,8 +50,6 @@
 
 #include <asm/unaligned.h>
 
-static void scsi_eh_done(struct scsi_cmnd *scmd);
-
 /*
  * These should *probably* be handled by the host itself.
  * Since it is allowed to sleep, it probably should.
@@ -63,11 +61,11 @@
 static enum scsi_disposition scsi_try_to_abort_cmd(struct scsi_host_template *,
 						   struct scsi_cmnd *);
 
-void scsi_eh_wakeup(struct Scsi_Host *shost)
+void scsi_eh_wakeup(struct Scsi_Host *shost, unsigned int busy)
 {
 	lockdep_assert_held(shost->host_lock);
 
-	if (scsi_host_busy(shost) == shost->host_failed) {
+	if (busy == shost->host_failed) {
 		trace_scsi_eh_wakeup(shost);
 		wake_up_process(shost->ehandler);
 		SCSI_LOG_ERROR_RECOVERY(5, shost_printk(KERN_INFO, shost,
@@ -90,7 +88,7 @@
 	if (scsi_host_set_state(shost, SHOST_RECOVERY) == 0 ||
 	    scsi_host_set_state(shost, SHOST_CANCEL_RECOVERY) == 0) {
 		shost->host_eh_scheduled++;
-		scsi_eh_wakeup(shost);
+		scsi_eh_wakeup(shost, scsi_host_busy(shost));
 	}
 
 	spin_unlock_irqrestore(shost->host_lock, flags);
@@ -135,6 +133,23 @@
 	return true;
 }
 
+static void scsi_eh_complete_abort(struct scsi_cmnd *scmd, struct Scsi_Host *shost)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(shost->host_lock, flags);
+	list_del_init(&scmd->eh_entry);
+	/*
+	 * If the abort succeeds, and there is no further
+	 * EH action, clear the ->last_reset time.
+	 */
+	if (list_empty(&shost->eh_abort_list) &&
+	    list_empty(&shost->eh_cmd_q))
+		if (shost->eh_deadline != -1)
+			shost->last_reset = 0;
+	spin_unlock_irqrestore(shost->host_lock, flags);
+}
+
 /**
  * scmd_eh_abort_handler - Handle command aborts
  * @work:	command to be aborted.
@@ -152,6 +167,7 @@
 		container_of(work, struct scsi_cmnd, abort_work.work);
 	struct scsi_device *sdev = scmd->device;
 	enum scsi_disposition rtn;
+	unsigned long flags;
 
 	if (scsi_host_eh_past_deadline(sdev->host)) {
 		SCSI_LOG_ERROR_RECOVERY(3,
@@ -175,12 +191,14 @@
 				SCSI_LOG_ERROR_RECOVERY(3,
 					scmd_printk(KERN_WARNING, scmd,
 						    "retry aborted command\n"));
+				scsi_eh_complete_abort(scmd, sdev->host);
 				scsi_queue_insert(scmd, SCSI_MLQUEUE_EH_RETRY);
 				return;
 			} else {
 				SCSI_LOG_ERROR_RECOVERY(3,
 					scmd_printk(KERN_WARNING, scmd,
 						    "finish aborted command\n"));
+				scsi_eh_complete_abort(scmd, sdev->host);
 				scsi_finish_command(scmd);
 				return;
 			}
@@ -193,6 +211,9 @@
 		}
 	}
 
+	spin_lock_irqsave(sdev->host->host_lock, flags);
+	list_del_init(&scmd->eh_entry);
+	spin_unlock_irqrestore(sdev->host->host_lock, flags);
 	scsi_eh_scmd_add(scmd);
 }
 
@@ -223,6 +244,8 @@
 	spin_lock_irqsave(shost->host_lock, flags);
 	if (shost->eh_deadline != -1 && !shost->last_reset)
 		shost->last_reset = jiffies;
+	BUG_ON(!list_empty(&scmd->eh_entry));
+	list_add_tail(&scmd->eh_entry, &shost->eh_abort_list);
 	spin_unlock_irqrestore(shost->host_lock, flags);
 
 	scmd->eh_eflags |= SCSI_EH_ABORT_SCHEDULED;
@@ -253,11 +276,12 @@
 {
 	struct scsi_cmnd *scmd = container_of(head, typeof(*scmd), rcu);
 	struct Scsi_Host *shost = scmd->device->host;
+	unsigned int busy = scsi_host_busy(shost);
 	unsigned long flags;
 
 	spin_lock_irqsave(shost->host_lock, flags);
 	shost->host_failed++;
-	scsi_eh_wakeup(shost);
+	scsi_eh_wakeup(shost, busy);
 	spin_unlock_irqrestore(shost->host_lock, flags);
 }
 
@@ -318,19 +342,11 @@
 
 	if (rtn == BLK_EH_DONE) {
 		/*
-		 * Set the command to complete first in order to prevent a real
-		 * completion from releasing the command while error handling
-		 * is using it. If the command was already completed, then the
-		 * lower level driver beat the timeout handler, and it is safe
-		 * to return without escalating error recovery.
-		 *
-		 * If timeout handling lost the race to a real completion, the
-		 * block layer may ignore that due to a fake timeout injection,
-		 * so return RESET_TIMER to allow error handling another shot
-		 * at this command.
+		 * If scsi_done() has already set SCMD_STATE_COMPLETE, do not
+		 * modify *scmd.
 		 */
 		if (test_and_set_bit(SCMD_STATE_COMPLETE, &scmd->state))
-			return BLK_EH_RESET_TIMER;
+			return BLK_EH_DONE;
 		if (scsi_abort_command(scmd) != SUCCESS) {
 			set_host_byte(scmd, DID_TIME_OUT);
 			scsi_eh_scmd_add(scmd);
@@ -460,8 +476,13 @@
 
 		if (sshdr->asc == 0x29) {
 			evt_type = SDEV_EVT_POWER_ON_RESET_OCCURRED;
-			sdev_printk(KERN_WARNING, sdev,
-				    "Power-on or device reset occurred\n");
+			/*
+			 * Do not print message if it is an expected side-effect
+			 * of runtime PM.
+			 */
+			if (!sdev->silence_suspend)
+				sdev_printk(KERN_WARNING, sdev,
+					    "Power-on or device reset occurred\n");
 		}
 
 		if (sshdr->asc == 0x2a && sshdr->ascq == 0x01) {
@@ -520,7 +541,8 @@
 		/* handler does not care. Drop down to default handling */
 	}
 
-	if (scmd->cmnd[0] == TEST_UNIT_READY && scmd->scsi_done != scsi_eh_done)
+	if (scmd->cmnd[0] == TEST_UNIT_READY &&
+	    scmd->submitter != SUBMITTED_BY_SCSI_ERROR_HANDLER)
 		/*
 		 * nasty: for mid-layer issued TURs, we need to return the
 		 * actual sense data without any recovery attempt.  For eh
@@ -782,7 +804,7 @@
  * scsi_eh_done - Completion function for error handling.
  * @scmd:	Cmd that is done.
  */
-static void scsi_eh_done(struct scsi_cmnd *scmd)
+void scsi_eh_done(struct scsi_cmnd *scmd)
 {
 	struct completion *eh_action;
 
@@ -1082,7 +1104,8 @@
 	shost->eh_action = &done;
 
 	scsi_log_send(scmd);
-	scmd->scsi_done = scsi_eh_done;
+	scmd->submitter = SUBMITTED_BY_SCSI_ERROR_HANDLER;
+	scmd->flags |= SCMD_LAST;
 
 	/*
 	 * Lock sdev->state_mutex to avoid that scsi_device_quiesce() can
@@ -1109,6 +1132,7 @@
 	if (rtn) {
 		if (timeleft > stall_for) {
 			scsi_eh_restore_cmnd(scmd, &ses);
+
 			timeleft -= stall_for;
 			msleep(jiffies_to_msecs(stall_for));
 			goto retry;
@@ -2338,11 +2362,6 @@
 }
 EXPORT_SYMBOL(scsi_report_device_reset);
 
-static void
-scsi_reset_provider_done_command(struct scsi_cmnd *scmd)
-{
-}
-
 /**
  * scsi_ioctl_reset: explicitly reset a host/bus/target/device
  * @dev:	scsi_device to operate on
@@ -2379,7 +2398,8 @@
 	scsi_init_command(dev, scmd);
 	scmd->cmnd = scsi_req(rq)->cmd;
 
-	scmd->scsi_done		= scsi_reset_provider_done_command;
+	scmd->submitter = SUBMITTED_BY_SCSI_RESET_IOCTL;
+	scmd->flags |= SCMD_LAST;
 	memset(&scmd->sdb, 0, sizeof(scmd->sdb));
 
 	scmd->cmd_len			= 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_ioctl.c
@@ -347,6 +347,8 @@
 {
 	struct scsi_request *req = scsi_req(rq);
 
+	if (hdr->cmd_len < 6)
+		return -EMSGSIZE;
 	if (copy_from_user(req->cmd, hdr->cmdp, hdr->cmd_len))
 		return -EFAULT;
 	if (!scsi_cmd_allowed(req->cmd, mode))
@@ -455,7 +457,7 @@
 		goto out_free_cdb;
 
 	ret = 0;
-	if (hdr->iovec_count) {
+	if (hdr->iovec_count && hdr->dxfer_len) {
 		struct iov_iter i;
 		struct iovec *iov = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_lib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_lib.c
@@ -281,9 +281,11 @@
 	rcu_read_lock();
 	__clear_bit(SCMD_STATE_INFLIGHT, &cmd->state);
 	if (unlikely(scsi_host_in_recovery(shost))) {
+		unsigned int busy = scsi_host_busy(shost);
+
 		spin_lock_irqsave(shost->host_lock, flags);
 		if (shost->host_failed || shost->host_eh_scheduled)
-			scsi_eh_wakeup(shost);
+			scsi_eh_wakeup(shost, busy);
 		spin_unlock_irqrestore(shost->host_lock, flags);
 	}
 	rcu_read_unlock();
@@ -1112,44 +1114,16 @@
 /* Called before a request is prepared. See also scsi_mq_prep_fn(). */
 void scsi_init_command(struct scsi_device *dev, struct scsi_cmnd *cmd)
 {
-	void *buf = cmd->sense_buffer;
-	void *prot = cmd->prot_sdb;
 	struct request *rq = scsi_cmd_to_rq(cmd);
-	unsigned int flags = cmd->flags & SCMD_PRESERVED_FLAGS;
-	unsigned long jiffies_at_alloc;
-	int retries, to_clear;
-	bool in_flight;
-	int budget_token = cmd->budget_token;
 
-	if (!blk_rq_is_passthrough(rq) && !(flags & SCMD_INITIALIZED)) {
-		flags |= SCMD_INITIALIZED;
+	if (!blk_rq_is_passthrough(rq) && !(cmd->flags & SCMD_INITIALIZED)) {
+		cmd->flags |= SCMD_INITIALIZED;
 		scsi_initialize_rq(rq);
 	}
 
-	jiffies_at_alloc = cmd->jiffies_at_alloc;
-	retries = cmd->retries;
-	in_flight = test_bit(SCMD_STATE_INFLIGHT, &cmd->state);
-	/*
-	 * Zero out the cmd, except for the embedded scsi_request. Only clear
-	 * the driver-private command data if the LLD does not supply a
-	 * function to initialize that data.
-	 */
-	to_clear = sizeof(*cmd) - sizeof(cmd->req);
-	if (!dev->host->hostt->init_cmd_priv)
-		to_clear += dev->host->hostt->cmd_size;
-	memset((char *)cmd + sizeof(cmd->req), 0, to_clear);
-
 	cmd->device = dev;
-	cmd->sense_buffer = buf;
-	cmd->prot_sdb = prot;
-	cmd->flags = flags;
+	INIT_LIST_HEAD(&cmd->eh_entry);
 	INIT_DELAYED_WORK(&cmd->abort_work, scmd_eh_abort_handler);
-	cmd->jiffies_at_alloc = jiffies_at_alloc;
-	cmd->retries = retries;
-	if (in_flight)
-		__set_bit(SCMD_STATE_INFLIGHT, &cmd->state);
-	cmd->budget_token = budget_token;
-
 }
 
 static blk_status_t scsi_setup_scsi_cmnd(struct scsi_device *sdev,
@@ -1174,8 +1148,6 @@
 	}
 
 	cmd->cmd_len = scsi_req(req)->cmd_len;
-	if (cmd->cmd_len == 0)
-		cmd->cmd_len = scsi_command_size(cmd->cmnd);
 	cmd->cmnd = scsi_req(req)->cmd;
 	cmd->transfersize = blk_rq_bytes(req);
 	cmd->allowed = scsi_req(req)->retries;
@@ -1477,6 +1449,7 @@
 		 */
 		SCSI_LOG_MLQUEUE(3, scmd_printk(KERN_INFO, cmd,
 			"queuecommand : device blocked\n"));
+		atomic_dec(&cmd->device->iorequest_cnt);
 		return SCSI_MLQUEUE_DEVICE_BUSY;
 	}
 
@@ -1509,6 +1482,7 @@
 	trace_scsi_dispatch_cmd_start(cmd);
 	rtn = host->hostt->queuecommand(host, cmd);
 	if (rtn) {
+		atomic_dec(&cmd->device->iorequest_cnt);
 		trace_scsi_dispatch_cmd_error(cmd, rtn);
 		if (rtn != SCSI_MLQUEUE_DEVICE_BUSY &&
 		    rtn != SCSI_MLQUEUE_TARGET_BUSY)
@@ -1536,10 +1510,28 @@
 	struct scsi_cmnd *cmd = blk_mq_rq_to_pdu(req);
 	struct scsi_device *sdev = req->q->queuedata;
 	struct Scsi_Host *shost = sdev->host;
+	bool in_flight = test_bit(SCMD_STATE_INFLIGHT, &cmd->state);
 	struct scatterlist *sg;
 
 	scsi_init_command(sdev, cmd);
 
+	cmd->eh_eflags = 0;
+	cmd->allowed = 0;
+	cmd->prot_type = 0;
+	cmd->prot_flags = 0;
+	cmd->submitter = 0;
+	cmd->cmd_len = 0;
+	cmd->cmnd = NULL;
+	memset(&cmd->sdb, 0, sizeof(cmd->sdb));
+	cmd->underflow = 0;
+	cmd->transfersize = 0;
+	cmd->host_scribble = NULL;
+	cmd->result = 0;
+	cmd->extra_len = 0;
+	cmd->state = 0;
+	if (in_flight)
+		__set_bit(SCMD_STATE_INFLIGHT, &cmd->state);
+
 	cmd->prot_op = SCSI_PROT_NORMAL;
 	if (blk_rq_bytes(req))
 		cmd->sc_data_direction = rq_dma_dir(req);
@@ -1575,8 +1567,17 @@
 	return scsi_cmd_to_driver(cmd)->init_command(cmd);
 }
 
-static void scsi_mq_done(struct scsi_cmnd *cmd)
+void scsi_done(struct scsi_cmnd *cmd)
 {
+	switch (cmd->submitter) {
+	case SUBMITTED_BY_BLOCK_LAYER:
+		break;
+	case SUBMITTED_BY_SCSI_ERROR_HANDLER:
+		return scsi_eh_done(cmd);
+	case SUBMITTED_BY_SCSI_RESET_IOCTL:
+		return;
+	}
+
 	if (unlikely(blk_should_fake_timeout(scsi_cmd_to_rq(cmd)->q)))
 		return;
 	if (unlikely(test_and_set_bit(SCMD_STATE_COMPLETE, &cmd->state)))
@@ -1584,6 +1585,7 @@
 	trace_scsi_dispatch_cmd_done(cmd);
 	blk_mq_complete_request(scsi_cmd_to_rq(cmd));
 }
+EXPORT_SYMBOL(scsi_done);
 
 static void scsi_mq_put_budget(struct request_queue *q, int budget_token)
 {
@@ -1666,6 +1668,13 @@
 	if (!scsi_host_queue_ready(q, shost, sdev, cmd))
 		goto out_dec_target_busy;
 
+	/*
+	 * Only clear the driver-private command data if the LLD does not supply
+	 * a function to initialize that data.
+	 */
+	if (shost->hostt->cmd_size && !shost->hostt->init_cmd_priv)
+		memset(cmd + 1, 0, shost->hostt->cmd_size);
+
 	if (!(req->rq_flags & RQF_DONTPREP)) {
 		ret = scsi_prepare_cmd(req);
 		if (ret != BLK_STS_OK)
@@ -1683,7 +1692,8 @@
 
 	scsi_set_resid(cmd, 0);
 	memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
-	cmd->scsi_done = scsi_mq_done;
+	cmd->submitter = SUBMITTED_BY_BLOCK_LAYER;
+	cmd->scsi_done = scsi_done;
 
 	blk_mq_start_request(req);
 	reason = scsi_dispatch_cmd(cmd);
@@ -1935,9 +1945,13 @@
 	return blk_mq_alloc_tag_set(tag_set);
 }
 
-void scsi_mq_destroy_tags(struct Scsi_Host *shost)
+void scsi_mq_free_tags(struct kref *kref)
 {
+	struct Scsi_Host *shost = container_of(kref, typeof(*shost),
+					       tagset_refcnt);
+
 	blk_mq_free_tag_set(&shost->tag_set);
+	complete(&shost->tagset_freed);
 }
 
 /**
@@ -2026,8 +2040,15 @@
 	memset(cmd, 0, sizeof(cmd));
 	cmd[1] = (pf ? 0x10 : 0) | (sp ? 0x01 : 0);
 
-	if (sdev->use_10_for_ms) {
-		if (len > 65535)
+	/*
+	 * Use MODE SELECT(10) if the device asked for it or if the mode page
+	 * and the mode select header cannot fit within the maximumm 255 bytes
+	 * of the MODE SELECT(6) command.
+	 */
+	if (sdev->use_10_for_ms ||
+	    len + 4 > 255 ||
+	    data->block_descriptor_length > 255) {
+		if (len > 65535 - 8)
 			return -EINVAL;
 		real_buffer = kmalloc(8 + len, GFP_KERNEL);
 		if (!real_buffer)
@@ -2040,15 +2061,13 @@
 		real_buffer[3] = data->device_specific;
 		real_buffer[4] = data->longlba ? 0x01 : 0;
 		real_buffer[5] = 0;
-		real_buffer[6] = data->block_descriptor_length >> 8;
-		real_buffer[7] = data->block_descriptor_length;
+		put_unaligned_be16(data->block_descriptor_length,
+				   &real_buffer[6]);
 
 		cmd[0] = MODE_SELECT_10;
-		cmd[7] = len >> 8;
-		cmd[8] = len;
+		put_unaligned_be16(len, &cmd[7]);
 	} else {
-		if (len > 255 || data->block_descriptor_length > 255 ||
-		    data->longlba)
+		if (data->longlba)
 			return -EINVAL;
 
 		real_buffer = kmalloc(4 + len, GFP_KERNEL);
@@ -2075,7 +2094,7 @@
 /**
  *	scsi_mode_sense - issue a mode sense, falling back from 10 to six bytes if necessary.
  *	@sdev:	SCSI device to be queried
- *	@dbd:	set if mode sense will allow block descriptors to be returned
+ *	@dbd:	set to prevent mode sense from returning block descriptors
  *	@modepage: mode page being requested
  *	@buffer: request buffer (may not be smaller than eight bytes)
  *	@len:	length of request buffer.
@@ -2110,18 +2129,18 @@
 		sshdr = &my_sshdr;
 
  retry:
-	use_10_for_ms = sdev->use_10_for_ms;
+	use_10_for_ms = sdev->use_10_for_ms || len > 255;
 
 	if (use_10_for_ms) {
-		if (len < 8)
-			len = 8;
+		if (len < 8 || len > 65535)
+			return -EINVAL;
 
 		cmd[0] = MODE_SENSE_10;
-		cmd[8] = len;
+		put_unaligned_be16(len, &cmd[7]);
 		header_length = 8;
 	} else {
 		if (len < 4)
-			len = 4;
+			return -EINVAL;
 
 		cmd[0] = MODE_SENSE;
 		cmd[4] = len;
@@ -2145,9 +2164,15 @@
 			if ((sshdr->sense_key == ILLEGAL_REQUEST) &&
 			    (sshdr->asc == 0x20) && (sshdr->ascq == 0)) {
 				/*
-				 * Invalid command operation code
+				 * Invalid command operation code: retry using
+				 * MODE SENSE(6) if this was a MODE SENSE(10)
+				 * request, except if the request mode page is
+				 * too large for MODE SENSE single byte
+				 * allocation length field.
 				 */
 				if (use_10_for_ms) {
+					if (len > 255)
+						return -EIO;
 					sdev->use_10_for_ms = 0;
 					goto retry;
 				}
@@ -2171,12 +2196,11 @@
 		data->longlba = 0;
 		data->block_descriptor_length = 0;
 	} else if (use_10_for_ms) {
-		data->length = buffer[0]*256 + buffer[1] + 2;
+		data->length = get_unaligned_be16(&buffer[0]) + 2;
 		data->medium_type = buffer[2];
 		data->device_specific = buffer[3];
 		data->longlba = buffer[4] & 0x01;
-		data->block_descriptor_length = buffer[6]*256
-			+ buffer[7];
+		data->block_descriptor_length = get_unaligned_be16(&buffer[6]);
 	} else {
 		data->length = buffer[0] + 1;
 		data->medium_type = buffer[1];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_pm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_pm.c
@@ -262,7 +262,7 @@
 	blk_pre_runtime_resume(sdev->request_queue);
 	if (pm && pm->runtime_resume)
 		err = pm->runtime_resume(dev);
-	blk_post_runtime_resume(sdev->request_queue, err);
+	blk_post_runtime_resume(sdev->request_queue);
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_priv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_priv.h
@@ -76,7 +76,7 @@
 extern enum blk_eh_timer_return scsi_times_out(struct request *req);
 extern int scsi_error_handler(void *host);
 extern enum scsi_disposition scsi_decide_disposition(struct scsi_cmnd *cmd);
-extern void scsi_eh_wakeup(struct Scsi_Host *shost);
+extern void scsi_eh_wakeup(struct Scsi_Host *shost, unsigned int busy);
 extern void scsi_eh_scmd_add(struct scsi_cmnd *);
 void scsi_eh_ready_devs(struct Scsi_Host *shost,
 			struct list_head *work_q,
@@ -84,6 +84,7 @@
 int scsi_eh_get_sense(struct list_head *work_q,
 		      struct list_head *done_q);
 int scsi_noretry_cmd(struct scsi_cmnd *scmd);
+void scsi_eh_done(struct scsi_cmnd *scmd);
 
 /* scsi_lib.c */
 extern int scsi_maybe_unblock_host(struct scsi_device *sdev);
@@ -94,7 +95,7 @@
 extern void scsi_requeue_run_queue(struct work_struct *work);
 extern void scsi_start_queue(struct scsi_device *sdev);
 extern int scsi_mq_setup_tags(struct Scsi_Host *shost);
-extern void scsi_mq_destroy_tags(struct Scsi_Host *shost);
+extern void scsi_mq_free_tags(struct kref *kref);
 extern void scsi_exit_queue(void);
 extern void scsi_evt_thread(struct work_struct *work);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_proc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_proc.c
@@ -311,7 +311,7 @@
 			       size_t length, loff_t *ppos)
 {
 	int host, channel, id, lun;
-	char *buffer, *p;
+	char *buffer, *end, *p;
 	int err;
 
 	if (!buf || length > PAGE_SIZE)
@@ -326,10 +326,14 @@
 		goto out;
 
 	err = -EINVAL;
-	if (length < PAGE_SIZE)
-		buffer[length] = '\0';
-	else if (buffer[PAGE_SIZE-1])
-		goto out;
+	if (length < PAGE_SIZE) {
+		end = buffer + length;
+		*end = '\0';
+	} else {
+		end = buffer + PAGE_SIZE - 1;
+		if (*end)
+			goto out;
+	}
 
 	/*
 	 * Usage: echo "scsi add-single-device 0 1 2 3" >/proc/scsi/scsi
@@ -338,10 +342,10 @@
 	if (!strncmp("scsi add-single-device", buffer, 22)) {
 		p = buffer + 23;
 
-		host = simple_strtoul(p, &p, 0);
-		channel = simple_strtoul(p + 1, &p, 0);
-		id = simple_strtoul(p + 1, &p, 0);
-		lun = simple_strtoul(p + 1, &p, 0);
+		host    = (p     < end) ? simple_strtoul(p, &p, 0) : 0;
+		channel = (p + 1 < end) ? simple_strtoul(p + 1, &p, 0) : 0;
+		id      = (p + 1 < end) ? simple_strtoul(p + 1, &p, 0) : 0;
+		lun     = (p + 1 < end) ? simple_strtoul(p + 1, &p, 0) : 0;
 
 		err = scsi_add_single_device(host, channel, id, lun);
 
@@ -352,10 +356,10 @@
 	} else if (!strncmp("scsi remove-single-device", buffer, 25)) {
 		p = buffer + 26;
 
-		host = simple_strtoul(p, &p, 0);
-		channel = simple_strtoul(p + 1, &p, 0);
-		id = simple_strtoul(p + 1, &p, 0);
-		lun = simple_strtoul(p + 1, &p, 0);
+		host    = (p     < end) ? simple_strtoul(p, &p, 0) : 0;
+		channel = (p + 1 < end) ? simple_strtoul(p + 1, &p, 0) : 0;
+		id      = (p + 1 < end) ? simple_strtoul(p + 1, &p, 0) : 0;
+		lun     = (p + 1 < end) ? simple_strtoul(p + 1, &p, 0) : 0;
 
 		err = scsi_remove_single_device(host, channel, id, lun);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_scan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_scan.c
@@ -198,6 +198,53 @@
 			 SCSI_TIMEOUT, 3, NULL);
 }
 
+static int scsi_realloc_sdev_budget_map(struct scsi_device *sdev,
+					unsigned int depth)
+{
+	int new_shift = sbitmap_calculate_shift(depth);
+	bool need_alloc = !sdev->budget_map.map;
+	bool need_free = false;
+	int ret;
+	struct sbitmap sb_backup;
+
+	depth = min_t(unsigned int, depth, scsi_device_max_queue_depth(sdev));
+
+	/*
+	 * realloc if new shift is calculated, which is caused by setting
+	 * up one new default queue depth after calling ->slave_configure
+	 */
+	if (!need_alloc && new_shift != sdev->budget_map.shift)
+		need_alloc = need_free = true;
+
+	if (!need_alloc)
+		return 0;
+
+	/*
+	 * Request queue has to be frozen for reallocating budget map,
+	 * and here disk isn't added yet, so freezing is pretty fast
+	 */
+	if (need_free) {
+		blk_mq_freeze_queue(sdev->request_queue);
+		sb_backup = sdev->budget_map;
+	}
+	ret = sbitmap_init_node(&sdev->budget_map,
+				scsi_device_max_queue_depth(sdev),
+				new_shift, GFP_NOIO,
+				sdev->request_queue->node, false, true);
+	if (!ret)
+		sbitmap_resize(&sdev->budget_map, depth);
+
+	if (need_free) {
+		if (ret)
+			sdev->budget_map = sb_backup;
+		else
+			sbitmap_free(&sb_backup);
+		ret = 0;
+		blk_mq_unfreeze_queue(sdev->request_queue);
+	}
+	return ret;
+}
+
 /**
  * scsi_alloc_sdev - allocate and setup a scsi_Device
  * @starget: which target to allocate a &scsi_device for
@@ -277,6 +324,7 @@
 		kfree(sdev);
 		goto out;
 	}
+	kref_get(&sdev->host->tagset_refcnt);
 	sdev->request_queue = q;
 	q->queuedata = sdev;
 	__scsi_init_queue(sdev->host, q);
@@ -291,11 +339,7 @@
 	 * default device queue depth to figure out sbitmap shift
 	 * since we use this queue depth most of times.
 	 */
-	if (sbitmap_init_node(&sdev->budget_map,
-				scsi_device_max_queue_depth(sdev),
-				sbitmap_calculate_shift(depth),
-				GFP_KERNEL, sdev->request_queue->node,
-				false, true)) {
+	if (scsi_realloc_sdev_budget_map(sdev, depth)) {
 		put_device(&starget->dev);
 		kfree(sdev);
 		goto out;
@@ -1001,6 +1045,13 @@
 			}
 			return SCSI_SCAN_NO_RESPONSE;
 		}
+
+		/*
+		 * The queue_depth is often changed in ->slave_configure.
+		 * Set up budget map again since memory consumption of
+		 * the map depends on actual queue depth.
+		 */
+		scsi_realloc_sdev_budget_map(sdev, sdev->queue_depth);
 	}
 
 	if (sdev->scsi_level >= SCSI_3)
@@ -1156,8 +1207,7 @@
 	 * that no LUN is present, so don't add sdev in these cases.
 	 * Two specific examples are:
 	 * 1) NetApp targets: return PQ=1, PDT=0x1f
-	 * 2) IBM/2145 targets: return PQ=1, PDT=0
-	 * 3) USB UFI: returns PDT=0x1f, with the PQ bits being "reserved"
+	 * 2) USB UFI: returns PDT=0x1f, with the PQ bits being "reserved"
 	 *    in the UFI 1.0 spec (we cannot rely on reserved bits).
 	 *
 	 * References:
@@ -1171,8 +1221,8 @@
 	 * PDT=00h Direct-access device (floppy)
 	 * PDT=1Fh none (no FDD connected to the requested logical unit)
 	 */
-	if (((result[0] >> 5) == 1 ||
-	    (starget->pdt_1f_for_no_lun && (result[0] & 0x1f) == 0x1f)) &&
+	if (((result[0] >> 5) == 1 || starget->pdt_1f_for_no_lun) &&
+	    (result[0] & 0x1f) == 0x1f &&
 	    !scsi_is_wlun(lun)) {
 		SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev,
 					"scsi scan: peripheral device type"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_sysfs.c
@@ -797,6 +797,7 @@
 	int i, ret;
 	struct scsi_device *sdev = to_scsi_device(dev);
 	enum scsi_device_state state = 0;
+	bool rescan_dev = false;
 
 	for (i = 0; i < ARRAY_SIZE(sdev_states); i++) {
 		const int len = strlen(sdev_states[i].name);
@@ -815,20 +816,35 @@
 	}
 
 	mutex_lock(&sdev->state_mutex);
-	ret = scsi_device_set_state(sdev, state);
-	/*
-	 * If the device state changes to SDEV_RUNNING, we need to
-	 * run the queue to avoid I/O hang, and rescan the device
-	 * to revalidate it. Running the queue first is necessary
-	 * because another thread may be waiting inside
-	 * blk_mq_freeze_queue_wait() and because that call may be
-	 * waiting for pending I/O to finish.
-	 */
-	if (ret == 0 && state == SDEV_RUNNING) {
+	switch (sdev->sdev_state) {
+	case SDEV_RUNNING:
+	case SDEV_OFFLINE:
+		break;
+	default:
+		mutex_unlock(&sdev->state_mutex);
+		return -EINVAL;
+	}
+	if (sdev->sdev_state == SDEV_RUNNING && state == SDEV_RUNNING) {
+		ret = 0;
+	} else {
+		ret = scsi_device_set_state(sdev, state);
+		if (ret == 0 && state == SDEV_RUNNING)
+			rescan_dev = true;
+	}
+	mutex_unlock(&sdev->state_mutex);
+
+	if (rescan_dev) {
+		/*
+		 * If the device state changes to SDEV_RUNNING, we need to
+		 * run the queue to avoid I/O hang, and rescan the device
+		 * to revalidate it. Running the queue first is necessary
+		 * because another thread may be waiting inside
+		 * blk_mq_freeze_queue_wait() and because that call may be
+		 * waiting for pending I/O to finish.
+		 */
 		blk_mq_run_hw_queues(sdev->request_queue, true);
 		scsi_rescan_device(dev);
 	}
-	mutex_unlock(&sdev->state_mutex);
 
 	return ret == 0 ? count : -EINVAL;
 }
@@ -1388,6 +1404,7 @@
 			 * We're treating error on bsg register as non-fatal, so
 			 * pretend nothing went wrong.
 			 */
+			error = PTR_ERR(sdev->bsg_dev);
 			sdev_printk(KERN_INFO, sdev,
 				    "Failed to register bsg queue, errno=%d\n",
 				    error);
@@ -1473,6 +1490,7 @@
 	mutex_unlock(&sdev->state_mutex);
 
 	blk_cleanup_queue(sdev->request_queue);
+	kref_put(&sdev->host->tagset_refcnt, scsi_mq_free_tags);
 	cancel_work_sync(&sdev->requeue_work);
 
 	if (sdev->host->hostt->slave_destroy)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_transport_fc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_transport_fc.c
@@ -34,7 +34,7 @@
 static int fc_bsg_rportadd(struct Scsi_Host *, struct fc_rport *);
 static void fc_bsg_remove(struct request_queue *);
 static void fc_bsg_goose_queue(struct fc_rport *);
-static void fc_li_stats_update(struct fc_fn_li_desc *li_desc,
+static void fc_li_stats_update(u16 event_type,
 			       struct fc_fpin_stats *stats);
 static void fc_delivery_stats_update(u32 reason_code,
 				     struct fc_fpin_stats *stats);
@@ -670,42 +670,34 @@
 EXPORT_SYMBOL(fc_find_rport_by_wwpn);
 
 static void
-fc_li_stats_update(struct fc_fn_li_desc *li_desc,
+fc_li_stats_update(u16 event_type,
 		   struct fc_fpin_stats *stats)
 {
-	stats->li += be32_to_cpu(li_desc->event_count);
-	switch (be16_to_cpu(li_desc->event_type)) {
+	stats->li++;
+	switch (event_type) {
 	case FPIN_LI_UNKNOWN:
-		stats->li_failure_unknown +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_failure_unknown++;
 		break;
 	case FPIN_LI_LINK_FAILURE:
-		stats->li_link_failure_count +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_link_failure_count++;
 		break;
 	case FPIN_LI_LOSS_OF_SYNC:
-		stats->li_loss_of_sync_count +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_loss_of_sync_count++;
 		break;
 	case FPIN_LI_LOSS_OF_SIG:
-		stats->li_loss_of_signals_count +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_loss_of_signals_count++;
 		break;
 	case FPIN_LI_PRIM_SEQ_ERR:
-		stats->li_prim_seq_err_count +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_prim_seq_err_count++;
 		break;
 	case FPIN_LI_INVALID_TX_WD:
-		stats->li_invalid_tx_word_count +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_invalid_tx_word_count++;
 		break;
 	case FPIN_LI_INVALID_CRC:
-		stats->li_invalid_crc_count +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_invalid_crc_count++;
 		break;
 	case FPIN_LI_DEVICE_SPEC:
-		stats->li_device_specific +=
-		    be32_to_cpu(li_desc->event_count);
+		stats->li_device_specific++;
 		break;
 	}
 }
@@ -767,6 +759,7 @@
 	struct fc_rport *attach_rport = NULL;
 	struct fc_host_attrs *fc_host = shost_to_fc_host(shost);
 	struct fc_fn_li_desc *li_desc = (struct fc_fn_li_desc *)tlv;
+	u16 event_type = be16_to_cpu(li_desc->event_type);
 	u64 wwpn;
 
 	rport = fc_find_rport_by_wwpn(shost,
@@ -775,7 +768,7 @@
 	    (rport->roles & FC_PORT_ROLE_FCP_TARGET ||
 	     rport->roles & FC_PORT_ROLE_NVME_TARGET)) {
 		attach_rport = rport;
-		fc_li_stats_update(li_desc, &attach_rport->fpin_stats);
+		fc_li_stats_update(event_type, &attach_rport->fpin_stats);
 	}
 
 	if (be32_to_cpu(li_desc->pname_count) > 0) {
@@ -789,14 +782,14 @@
 			    rport->roles & FC_PORT_ROLE_NVME_TARGET)) {
 				if (rport == attach_rport)
 					continue;
-				fc_li_stats_update(li_desc,
+				fc_li_stats_update(event_type,
 						   &rport->fpin_stats);
 			}
 		}
 	}
 
 	if (fc_host->port_name == be64_to_cpu(li_desc->attached_wwpn))
-		fc_li_stats_update(li_desc, &fc_host->fpin_stats);
+		fc_li_stats_update(event_type, &fc_host->fpin_stats);
 }
 
 /*
@@ -1257,7 +1250,7 @@
 		 */
 		if (rport->port_state == FC_PORTSTATE_ONLINE)
 			rport->port_state = port_state;
-		else
+		else if (port_state != rport->port_state)
 			return -EINVAL;
 	} else if (port_state == FC_PORTSTATE_ONLINE) {
 		/*
@@ -1267,7 +1260,7 @@
 		 */
 		if (rport->port_state == FC_PORTSTATE_MARGINAL)
 			rport->port_state = port_state;
-		else
+		else if (port_state != rport->port_state)
 			return -EINVAL;
 	} else
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_transport_iscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_transport_iscsi.c
@@ -86,6 +86,9 @@
 	struct transport_container session_cont;
 };
 
+static DEFINE_IDR(iscsi_ep_idr);
+static DEFINE_MUTEX(iscsi_ep_idr_mutex);
+
 static atomic_t iscsi_session_nr; /* sysfs session id for next new session */
 static struct workqueue_struct *iscsi_eh_timer_workq;
 
@@ -169,6 +172,11 @@
 static void iscsi_endpoint_release(struct device *dev)
 {
 	struct iscsi_endpoint *ep = iscsi_dev_to_endpoint(dev);
+
+	mutex_lock(&iscsi_ep_idr_mutex);
+	idr_remove(&iscsi_ep_idr, ep->id);
+	mutex_unlock(&iscsi_ep_idr_mutex);
+
 	kfree(ep);
 }
 
@@ -181,7 +189,7 @@
 show_ep_handle(struct device *dev, struct device_attribute *attr, char *buf)
 {
 	struct iscsi_endpoint *ep = iscsi_dev_to_endpoint(dev);
-	return sysfs_emit(buf, "%llu\n", (unsigned long long) ep->id);
+	return sysfs_emit(buf, "%d\n", ep->id);
 }
 static ISCSI_ATTR(ep, handle, S_IRUGO, show_ep_handle, NULL);
 
@@ -194,48 +202,37 @@
 	.attrs = iscsi_endpoint_attrs,
 };
 
-#define ISCSI_MAX_EPID -1
-
-static int iscsi_match_epid(struct device *dev, const void *data)
-{
-	struct iscsi_endpoint *ep = iscsi_dev_to_endpoint(dev);
-	const uint64_t *epid = data;
-
-	return *epid == ep->id;
-}
-
 struct iscsi_endpoint *
 iscsi_create_endpoint(int dd_size)
 {
-	struct device *dev;
 	struct iscsi_endpoint *ep;
-	uint64_t id;
-	int err;
-
-	for (id = 1; id < ISCSI_MAX_EPID; id++) {
-		dev = class_find_device(&iscsi_endpoint_class, NULL, &id,
-					iscsi_match_epid);
-		if (!dev)
-			break;
-		else
-			put_device(dev);
-	}
-	if (id == ISCSI_MAX_EPID) {
-		printk(KERN_ERR "Too many connections. Max supported %u\n",
-		       ISCSI_MAX_EPID - 1);
-		return NULL;
-	}
+	int err, id;
 
 	ep = kzalloc(sizeof(*ep) + dd_size, GFP_KERNEL);
 	if (!ep)
 		return NULL;
 
+	mutex_lock(&iscsi_ep_idr_mutex);
+
+	/*
+	 * First endpoint id should be 1 to comply with user space
+	 * applications (iscsid).
+	 */
+	id = idr_alloc(&iscsi_ep_idr, ep, 1, -1, GFP_NOIO);
+	if (id < 0) {
+		mutex_unlock(&iscsi_ep_idr_mutex);
+		printk(KERN_ERR "Could not allocate endpoint ID. Error %d.\n",
+		       id);
+		goto free_ep;
+	}
+	mutex_unlock(&iscsi_ep_idr_mutex);
+
 	ep->id = id;
 	ep->dev.class = &iscsi_endpoint_class;
-	dev_set_name(&ep->dev, "ep-%llu", (unsigned long long) id);
+	dev_set_name(&ep->dev, "ep-%d", id);
 	err = device_register(&ep->dev);
         if (err)
-                goto free_ep;
+		goto put_dev;
 
 	err = sysfs_create_group(&ep->dev.kobj, &iscsi_endpoint_group);
 	if (err)
@@ -249,6 +246,12 @@
 	device_unregister(&ep->dev);
 	return NULL;
 
+put_dev:
+	mutex_lock(&iscsi_ep_idr_mutex);
+	idr_remove(&iscsi_ep_idr, id);
+	mutex_unlock(&iscsi_ep_idr_mutex);
+	put_device(&ep->dev);
+	return NULL;
 free_ep:
 	kfree(ep);
 	return NULL;
@@ -276,14 +279,17 @@
  */
 struct iscsi_endpoint *iscsi_lookup_endpoint(u64 handle)
 {
-	struct device *dev;
+	struct iscsi_endpoint *ep;
 
-	dev = class_find_device(&iscsi_endpoint_class, NULL, &handle,
-				iscsi_match_epid);
-	if (!dev)
-		return NULL;
+	mutex_lock(&iscsi_ep_idr_mutex);
+	ep = idr_find(&iscsi_ep_idr, handle);
+	if (!ep)
+		goto unlock;
 
-	return iscsi_dev_to_endpoint(dev);
+	get_device(&ep->dev);
+unlock:
+	mutex_unlock(&iscsi_ep_idr_mutex);
+	return ep;
 }
 EXPORT_SYMBOL_GPL(iscsi_lookup_endpoint);
 
@@ -763,7 +769,7 @@
 
 	err = device_register(&iface->dev);
 	if (err)
-		goto free_iface;
+		goto put_dev;
 
 	err = sysfs_create_group(&iface->dev.kobj, &iscsi_iface_group);
 	if (err)
@@ -777,9 +783,8 @@
 	device_unregister(&iface->dev);
 	return NULL;
 
-free_iface:
-	put_device(iface->dev.parent);
-	kfree(iface);
+put_dev:
+	put_device(&iface->dev);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(iscsi_create_iface);
@@ -1248,15 +1253,15 @@
 
 	err = device_register(&fnode_sess->dev);
 	if (err)
-		goto free_fnode_sess;
+		goto put_dev;
 
 	if (dd_size)
 		fnode_sess->dd_data = &fnode_sess[1];
 
 	return fnode_sess;
 
-free_fnode_sess:
-	kfree(fnode_sess);
+put_dev:
+	put_device(&fnode_sess->dev);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(iscsi_create_flashnode_sess);
@@ -1296,15 +1301,15 @@
 
 	err = device_register(&fnode_conn->dev);
 	if (err)
-		goto free_fnode_conn;
+		goto put_dev;
 
 	if (dd_size)
 		fnode_conn->dd_data = &fnode_conn[1];
 
 	return fnode_conn;
 
-free_fnode_conn:
-	kfree(fnode_conn);
+put_dev:
+	put_device(&fnode_conn->dev);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(iscsi_create_flashnode_conn);
@@ -1674,6 +1679,13 @@
 	return name;
 }
 
+static char *iscsi_session_target_state_name[] = {
+	[ISCSI_SESSION_TARGET_UNBOUND]   = "UNBOUND",
+	[ISCSI_SESSION_TARGET_ALLOCATED] = "ALLOCATED",
+	[ISCSI_SESSION_TARGET_SCANNED]   = "SCANNED",
+	[ISCSI_SESSION_TARGET_UNBINDING] = "UNBINDING",
+};
+
 int iscsi_session_chkready(struct iscsi_cls_session *session)
 {
 	int err;
@@ -1802,9 +1814,13 @@
 		if ((scan_data->channel == SCAN_WILD_CARD ||
 		     scan_data->channel == 0) &&
 		    (scan_data->id == SCAN_WILD_CARD ||
-		     scan_data->id == id))
+		     scan_data->id == id)) {
 			scsi_scan_target(&session->dev, 0, id,
 					 scan_data->lun, scan_data->rescan);
+			spin_lock_irqsave(&session->lock, flags);
+			session->target_state = ISCSI_SESSION_TARGET_SCANNED;
+			spin_unlock_irqrestore(&session->lock, flags);
+		}
 	}
 
 user_scan_exit:
@@ -1899,12 +1915,12 @@
 	}
 	spin_unlock_irqrestore(&session->lock, flags);
 
-	if (session->transport->session_recovery_timedout)
-		session->transport->session_recovery_timedout(session);
-
 	ISCSI_DBG_TRANS_SESSION(session, "Unblocking SCSI target\n");
 	scsi_target_unblock(&session->dev, SDEV_TRANSPORT_OFFLINE);
 	ISCSI_DBG_TRANS_SESSION(session, "Completed unblocking SCSI target\n");
+
+	if (session->transport->session_recovery_timedout)
+		session->transport->session_recovery_timedout(session);
 }
 
 static void __iscsi_unblock_session(struct work_struct *work)
@@ -1993,31 +2009,41 @@
 	struct iscsi_cls_host *ihost = shost->shost_data;
 	unsigned long flags;
 	unsigned int target_id;
+	bool remove_target = true;
 
 	ISCSI_DBG_TRANS_SESSION(session, "Unbinding session\n");
 
 	/* Prevent new scans and make sure scanning is not in progress */
 	mutex_lock(&ihost->mutex);
 	spin_lock_irqsave(&session->lock, flags);
-	if (session->target_id == ISCSI_MAX_TARGET) {
+	if (session->target_state == ISCSI_SESSION_TARGET_ALLOCATED) {
+		remove_target = false;
+	} else if (session->target_state != ISCSI_SESSION_TARGET_SCANNED) {
 		spin_unlock_irqrestore(&session->lock, flags);
 		mutex_unlock(&ihost->mutex);
-		goto unbind_session_exit;
+		ISCSI_DBG_TRANS_SESSION(session,
+			"Skipping target unbinding: Session is unbound/unbinding.\n");
+		return;
 	}
 
+	session->target_state = ISCSI_SESSION_TARGET_UNBINDING;
 	target_id = session->target_id;
 	session->target_id = ISCSI_MAX_TARGET;
 	spin_unlock_irqrestore(&session->lock, flags);
 	mutex_unlock(&ihost->mutex);
 
-	scsi_remove_target(&session->dev);
+	if (remove_target)
+		scsi_remove_target(&session->dev);
 
 	if (session->ida_used)
 		ida_simple_remove(&iscsi_sess_ida, target_id);
 
-unbind_session_exit:
 	iscsi_session_event(session, ISCSI_KEVENT_UNBIND_SESSION);
 	ISCSI_DBG_TRANS_SESSION(session, "Completed target removal\n");
+
+	spin_lock_irqsave(&session->lock, flags);
+	session->target_state = ISCSI_SESSION_TARGET_UNBOUND;
+	spin_unlock_irqrestore(&session->lock, flags);
 }
 
 static void __iscsi_destroy_session(struct work_struct *work)
@@ -2086,6 +2112,9 @@
 		session->ida_used = true;
 	} else
 		session->target_id = target_id;
+	spin_lock_irqsave(&session->lock, flags);
+	session->target_state = ISCSI_SESSION_TARGET_ALLOCATED;
+	spin_unlock_irqrestore(&session->lock, flags);
 
 	dev_set_name(&session->dev, "session%u", session->sid);
 	err = device_add(&session->dev);
@@ -2221,10 +2250,10 @@
 
 	switch (flag) {
 	case STOP_CONN_RECOVER:
-		conn->state = ISCSI_CONN_FAILED;
+		WRITE_ONCE(conn->state, ISCSI_CONN_FAILED);
 		break;
 	case STOP_CONN_TERM:
-		conn->state = ISCSI_CONN_DOWN;
+		WRITE_ONCE(conn->state, ISCSI_CONN_DOWN);
 		break;
 	default:
 		iscsi_cls_conn_printk(KERN_ERR, conn, "invalid stop flag %d\n",
@@ -2236,16 +2265,51 @@
 	ISCSI_DBG_TRANS_CONN(conn, "Stopping conn done.\n");
 }
 
-static int iscsi_if_stop_conn(struct iscsi_transport *transport,
-			      struct iscsi_uevent *ev)
+static void iscsi_ep_disconnect(struct iscsi_cls_conn *conn, bool is_active)
 {
-	int flag = ev->u.stop_conn.flag;
-	struct iscsi_cls_conn *conn;
+	struct iscsi_cls_session *session = iscsi_conn_to_session(conn);
+	struct iscsi_endpoint *ep;
 
-	conn = iscsi_conn_lookup(ev->u.stop_conn.sid, ev->u.stop_conn.cid);
-	if (!conn)
-		return -EINVAL;
+	ISCSI_DBG_TRANS_CONN(conn, "disconnect ep.\n");
+	WRITE_ONCE(conn->state, ISCSI_CONN_FAILED);
+
+	if (!conn->ep || !session->transport->ep_disconnect)
+		return;
+
+	ep = conn->ep;
+	conn->ep = NULL;
+
+	session->transport->unbind_conn(conn, is_active);
+	session->transport->ep_disconnect(ep);
+	ISCSI_DBG_TRANS_CONN(conn, "disconnect ep done.\n");
+}
 
+static void iscsi_if_disconnect_bound_ep(struct iscsi_cls_conn *conn,
+					 struct iscsi_endpoint *ep,
+					 bool is_active)
+{
+	/* Check if this was a conn error and the kernel took ownership */
+	spin_lock_irq(&conn->lock);
+	if (!test_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags)) {
+		spin_unlock_irq(&conn->lock);
+		iscsi_ep_disconnect(conn, is_active);
+	} else {
+		spin_unlock_irq(&conn->lock);
+		ISCSI_DBG_TRANS_CONN(conn, "flush kernel conn cleanup.\n");
+		mutex_unlock(&conn->ep_mutex);
+
+		flush_work(&conn->cleanup_work);
+		/*
+		 * Userspace is now done with the EP so we can release the ref
+		 * iscsi_cleanup_conn_work_fn took.
+		 */
+		iscsi_put_endpoint(ep);
+		mutex_lock(&conn->ep_mutex);
+	}
+}
+
+static int iscsi_if_stop_conn(struct iscsi_cls_conn *conn, int flag)
+{
 	ISCSI_DBG_TRANS_CONN(conn, "iscsi if conn stop.\n");
 	/*
 	 * If this is a termination we have to call stop_conn with that flag
@@ -2257,11 +2321,24 @@
 		iscsi_stop_conn(conn, flag);
 	} else {
 		/*
+		 * For offload, when iscsid is restarted it won't know about
+		 * existing endpoints so it can't do a ep_disconnect. We clean
+		 * it up here for userspace.
+		 */
+		mutex_lock(&conn->ep_mutex);
+		if (conn->ep)
+			iscsi_if_disconnect_bound_ep(conn, conn->ep, true);
+		mutex_unlock(&conn->ep_mutex);
+
+		/*
 		 * Figure out if it was the kernel or userspace initiating this.
 		 */
+		spin_lock_irq(&conn->lock);
 		if (!test_and_set_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags)) {
+			spin_unlock_irq(&conn->lock);
 			iscsi_stop_conn(conn, flag);
 		} else {
+			spin_unlock_irq(&conn->lock);
 			ISCSI_DBG_TRANS_CONN(conn,
 					     "flush kernel conn cleanup.\n");
 			flush_work(&conn->cleanup_work);
@@ -2270,31 +2347,14 @@
 		 * Only clear for recovery to avoid extra cleanup runs during
 		 * termination.
 		 */
+		spin_lock_irq(&conn->lock);
 		clear_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags);
+		spin_unlock_irq(&conn->lock);
 	}
 	ISCSI_DBG_TRANS_CONN(conn, "iscsi if conn stop done.\n");
 	return 0;
 }
 
-static void iscsi_ep_disconnect(struct iscsi_cls_conn *conn, bool is_active)
-{
-	struct iscsi_cls_session *session = iscsi_conn_to_session(conn);
-	struct iscsi_endpoint *ep;
-
-	ISCSI_DBG_TRANS_CONN(conn, "disconnect ep.\n");
-	conn->state = ISCSI_CONN_FAILED;
-
-	if (!conn->ep || !session->transport->ep_disconnect)
-		return;
-
-	ep = conn->ep;
-	conn->ep = NULL;
-
-	session->transport->unbind_conn(conn, is_active);
-	session->transport->ep_disconnect(ep);
-	ISCSI_DBG_TRANS_CONN(conn, "disconnect ep done.\n");
-}
-
 static void iscsi_cleanup_conn_work_fn(struct work_struct *work)
 {
 	struct iscsi_cls_conn *conn = container_of(work, struct iscsi_cls_conn,
@@ -2303,18 +2363,11 @@
 
 	mutex_lock(&conn->ep_mutex);
 	/*
-	 * If we are not at least bound there is nothing for us to do. Userspace
-	 * will do a ep_disconnect call if offload is used, but will not be
-	 * doing a stop since there is nothing to clean up, so we have to clear
-	 * the cleanup bit here.
+	 * Get a ref to the ep, so we don't release its ID until after
+	 * userspace is done referencing it in iscsi_if_disconnect_bound_ep.
 	 */
-	if (conn->state != ISCSI_CONN_BOUND && conn->state != ISCSI_CONN_UP) {
-		ISCSI_DBG_TRANS_CONN(conn, "Got error while conn is already failed. Ignoring.\n");
-		clear_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags);
-		mutex_unlock(&conn->ep_mutex);
-		return;
-	}
-
+	if (conn->ep)
+		get_device(&conn->ep->dev);
 	iscsi_ep_disconnect(conn, false);
 
 	if (system_state != SYSTEM_RUNNING) {
@@ -2332,6 +2385,55 @@
 	ISCSI_DBG_TRANS_CONN(conn, "cleanup done.\n");
 }
 
+static int iscsi_iter_force_destroy_conn_fn(struct device *dev, void *data)
+{
+	struct iscsi_transport *transport;
+	struct iscsi_cls_conn *conn;
+
+	if (!iscsi_is_conn_dev(dev))
+		return 0;
+
+	conn = iscsi_dev_to_conn(dev);
+	transport = conn->transport;
+
+	if (READ_ONCE(conn->state) != ISCSI_CONN_DOWN)
+		iscsi_if_stop_conn(conn, STOP_CONN_TERM);
+
+	transport->destroy_conn(conn);
+	return 0;
+}
+
+/**
+ * iscsi_force_destroy_session - destroy a session from the kernel
+ * @session: session to destroy
+ *
+ * Force the destruction of a session from the kernel. This should only be
+ * used when userspace is no longer running during system shutdown.
+ */
+void iscsi_force_destroy_session(struct iscsi_cls_session *session)
+{
+	struct iscsi_transport *transport = session->transport;
+	unsigned long flags;
+
+	WARN_ON_ONCE(system_state == SYSTEM_RUNNING);
+
+	spin_lock_irqsave(&sesslock, flags);
+	if (list_empty(&session->sess_list)) {
+		spin_unlock_irqrestore(&sesslock, flags);
+		/*
+		 * Conn/ep is already freed. Session is being torn down via
+		 * async path. For shutdown we don't care about it so return.
+		 */
+		return;
+	}
+	spin_unlock_irqrestore(&sesslock, flags);
+
+	device_for_each_child(&session->dev, NULL,
+			      iscsi_iter_force_destroy_conn_fn);
+	transport->destroy_session(session);
+}
+EXPORT_SYMBOL_GPL(iscsi_force_destroy_session);
+
 void iscsi_free_session(struct iscsi_cls_session *session)
 {
 	ISCSI_DBG_TRANS_SESSION(session, "Freeing session\n");
@@ -2370,11 +2472,12 @@
 		conn->dd_data = &conn[1];
 
 	mutex_init(&conn->ep_mutex);
+	spin_lock_init(&conn->lock);
 	INIT_LIST_HEAD(&conn->conn_list);
 	INIT_WORK(&conn->cleanup_work, iscsi_cleanup_conn_work_fn);
 	conn->transport = transport;
 	conn->cid = cid;
-	conn->state = ISCSI_CONN_DOWN;
+	WRITE_ONCE(conn->state, ISCSI_CONN_DOWN);
 
 	/* this is released in the dev's release function */
 	if (!get_device(&session->dev))
@@ -2561,9 +2664,32 @@
 	struct iscsi_uevent *ev;
 	struct iscsi_internal *priv;
 	int len = nlmsg_total_size(sizeof(*ev));
+	unsigned long flags;
+	int state;
 
-	if (!test_and_set_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags))
-		queue_work(iscsi_conn_cleanup_workq, &conn->cleanup_work);
+	spin_lock_irqsave(&conn->lock, flags);
+	/*
+	 * Userspace will only do a stop call if we are at least bound. And, we
+	 * only need to do the in kernel cleanup if in the UP state so cmds can
+	 * be released to upper layers. If in other states just wait for
+	 * userspace to avoid races that can leave the cleanup_work queued.
+	 */
+	state = READ_ONCE(conn->state);
+	switch (state) {
+	case ISCSI_CONN_BOUND:
+	case ISCSI_CONN_UP:
+		if (!test_and_set_bit(ISCSI_CLS_CONN_BIT_CLEANUP,
+				      &conn->flags)) {
+			queue_work(iscsi_conn_cleanup_workq,
+				   &conn->cleanup_work);
+		}
+		break;
+	default:
+		ISCSI_DBG_TRANS_CONN(conn, "Got conn error in state %d\n",
+				     state);
+		break;
+	}
+	spin_unlock_irqrestore(&conn->lock, flags);
 
 	priv = iscsi_if_transport_lookup(conn->transport);
 	if (!priv)
@@ -2908,14 +3034,15 @@
 }
 
 static int
-iscsi_set_param(struct iscsi_transport *transport, struct iscsi_uevent *ev)
+iscsi_if_set_param(struct iscsi_transport *transport, struct iscsi_uevent *ev, u32 rlen)
 {
 	char *data = (char*)ev + sizeof(*ev);
 	struct iscsi_cls_conn *conn;
 	struct iscsi_cls_session *session;
-	int err = 0, value = 0;
+	int err = 0, value = 0, state;
 
-	if (ev->u.set_param.len > PAGE_SIZE)
+	if (ev->u.set_param.len > rlen ||
+	    ev->u.set_param.len > PAGE_SIZE)
 		return -EINVAL;
 
 	session = iscsi_session_lookup(ev->u.set_param.sid);
@@ -2923,6 +3050,10 @@
 	if (!conn || !session)
 		return -EINVAL;
 
+	/* data will be regarded as NULL-ended string, do length check */
+	if (strlen(data) > ev->u.set_param.len)
+		return -EINVAL;
+
 	switch (ev->u.set_param.param) {
 	case ISCSI_PARAM_SESS_RECOVERY_TMO:
 		sscanf(data, "%d", &value);
@@ -2930,8 +3061,8 @@
 			session->recovery_tmo = value;
 		break;
 	default:
-		if ((conn->state == ISCSI_CONN_BOUND) ||
-			(conn->state == ISCSI_CONN_UP)) {
+		state = READ_ONCE(conn->state);
+		if (state == ISCSI_CONN_BOUND || state == ISCSI_CONN_UP) {
 			err = transport->set_param(conn, ev->u.set_param.param,
 					data, ev->u.set_param.len);
 		} else {
@@ -3003,16 +3134,7 @@
 	}
 
 	mutex_lock(&conn->ep_mutex);
-	/* Check if this was a conn error and the kernel took ownership */
-	if (test_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags)) {
-		ISCSI_DBG_TRANS_CONN(conn, "flush kernel conn cleanup.\n");
-		mutex_unlock(&conn->ep_mutex);
-
-		flush_work(&conn->cleanup_work);
-		goto put_ep;
-	}
-
-	iscsi_ep_disconnect(conn, false);
+	iscsi_if_disconnect_bound_ep(conn, ep, false);
 	mutex_unlock(&conn->ep_mutex);
 put_ep:
 	iscsi_put_endpoint(ep);
@@ -3021,7 +3143,7 @@
 
 static int
 iscsi_if_transport_ep(struct iscsi_transport *transport,
-		      struct iscsi_uevent *ev, int msg_type)
+		      struct iscsi_uevent *ev, int msg_type, u32 rlen)
 {
 	struct iscsi_endpoint *ep;
 	int rc = 0;
@@ -3029,7 +3151,10 @@
 	switch (msg_type) {
 	case ISCSI_UEVENT_TRANSPORT_EP_CONNECT_THROUGH_HOST:
 	case ISCSI_UEVENT_TRANSPORT_EP_CONNECT:
-		rc = iscsi_if_ep_connect(transport, ev, msg_type);
+		if (rlen < sizeof(struct sockaddr))
+			rc = -EINVAL;
+		else
+			rc = iscsi_if_ep_connect(transport, ev, msg_type);
 		break;
 	case ISCSI_UEVENT_TRANSPORT_EP_POLL:
 		if (!transport->ep_poll)
@@ -3053,12 +3178,15 @@
 
 static int
 iscsi_tgt_dscvr(struct iscsi_transport *transport,
-		struct iscsi_uevent *ev)
+		struct iscsi_uevent *ev, u32 rlen)
 {
 	struct Scsi_Host *shost;
 	struct sockaddr *dst_addr;
 	int err;
 
+	if (rlen < sizeof(*dst_addr))
+		return -EINVAL;
+
 	if (!transport->tgt_dscvr)
 		return -EINVAL;
 
@@ -3079,7 +3207,7 @@
 
 static int
 iscsi_set_host_param(struct iscsi_transport *transport,
-		     struct iscsi_uevent *ev)
+		     struct iscsi_uevent *ev, u32 rlen)
 {
 	char *data = (char*)ev + sizeof(*ev);
 	struct Scsi_Host *shost;
@@ -3088,7 +3216,8 @@
 	if (!transport->set_host_param)
 		return -ENOSYS;
 
-	if (ev->u.set_host_param.len > PAGE_SIZE)
+	if (ev->u.set_host_param.len > rlen ||
+	    ev->u.set_host_param.len > PAGE_SIZE)
 		return -EINVAL;
 
 	shost = scsi_host_lookup(ev->u.set_host_param.host_no);
@@ -3098,6 +3227,10 @@
 		return -ENODEV;
 	}
 
+	/* see similar check in iscsi_if_set_param() */
+	if (strlen(data) > ev->u.set_host_param.len)
+		return -EINVAL;
+
 	err = transport->set_host_param(shost, ev->u.set_host_param.param,
 					data, ev->u.set_host_param.len);
 	scsi_host_put(shost);
@@ -3105,12 +3238,15 @@
 }
 
 static int
-iscsi_set_path(struct iscsi_transport *transport, struct iscsi_uevent *ev)
+iscsi_set_path(struct iscsi_transport *transport, struct iscsi_uevent *ev, u32 rlen)
 {
 	struct Scsi_Host *shost;
 	struct iscsi_path *params;
 	int err;
 
+	if (rlen < sizeof(*params))
+		return -EINVAL;
+
 	if (!transport->set_path)
 		return -ENOSYS;
 
@@ -3170,12 +3306,15 @@
 }
 
 static int
-iscsi_send_ping(struct iscsi_transport *transport, struct iscsi_uevent *ev)
+iscsi_send_ping(struct iscsi_transport *transport, struct iscsi_uevent *ev, u32 rlen)
 {
 	struct Scsi_Host *shost;
 	struct sockaddr *dst_addr;
 	int err;
 
+	if (rlen < sizeof(*dst_addr))
+		return -EINVAL;
+
 	if (!transport->send_ping)
 		return -ENOSYS;
 
@@ -3673,13 +3812,12 @@
 }
 
 static int iscsi_if_transport_conn(struct iscsi_transport *transport,
-				   struct nlmsghdr *nlh)
+				   struct nlmsghdr *nlh, u32 pdu_len)
 {
 	struct iscsi_uevent *ev = nlmsg_data(nlh);
 	struct iscsi_cls_session *session;
 	struct iscsi_cls_conn *conn = NULL;
 	struct iscsi_endpoint *ep;
-	uint32_t pdu_len;
 	int err = 0;
 
 	switch (nlh->nlmsg_type) {
@@ -3688,7 +3826,12 @@
 	case ISCSI_UEVENT_DESTROY_CONN:
 		return iscsi_if_destroy_conn(transport, ev);
 	case ISCSI_UEVENT_STOP_CONN:
-		return iscsi_if_stop_conn(transport, ev);
+		conn = iscsi_conn_lookup(ev->u.stop_conn.sid,
+					 ev->u.stop_conn.cid);
+		if (!conn)
+			return -EINVAL;
+
+		return iscsi_if_stop_conn(conn, ev->u.stop_conn.flag);
 	}
 
 	/*
@@ -3715,24 +3858,17 @@
 		return -EINVAL;
 
 	mutex_lock(&conn->ep_mutex);
+	spin_lock_irq(&conn->lock);
 	if (test_bit(ISCSI_CLS_CONN_BIT_CLEANUP, &conn->flags)) {
+		spin_unlock_irq(&conn->lock);
 		mutex_unlock(&conn->ep_mutex);
 		ev->r.retcode = -ENOTCONN;
 		return 0;
 	}
+	spin_unlock_irq(&conn->lock);
 
 	switch (nlh->nlmsg_type) {
 	case ISCSI_UEVENT_BIND_CONN:
-		if (conn->ep) {
-			/*
-			 * For offload boot support where iscsid is restarted
-			 * during the pivot root stage, the ep will be intact
-			 * here when the new iscsid instance starts up and
-			 * reconnects.
-			 */
-			iscsi_ep_disconnect(conn, true);
-		}
-
 		session = iscsi_session_lookup(ev->u.b_conn.sid);
 		if (!session) {
 			err = -EINVAL;
@@ -3743,7 +3879,7 @@
 						ev->u.b_conn.transport_eph,
 						ev->u.b_conn.is_leading);
 		if (!ev->r.retcode)
-			conn->state = ISCSI_CONN_BOUND;
+			WRITE_ONCE(conn->state, ISCSI_CONN_BOUND);
 
 		if (ev->r.retcode || !transport->ep_connect)
 			break;
@@ -3762,11 +3898,10 @@
 	case ISCSI_UEVENT_START_CONN:
 		ev->r.retcode = transport->start_conn(conn);
 		if (!ev->r.retcode)
-			conn->state = ISCSI_CONN_UP;
+			WRITE_ONCE(conn->state, ISCSI_CONN_UP);
+
 		break;
 	case ISCSI_UEVENT_SEND_PDU:
-		pdu_len = nlh->nlmsg_len - sizeof(*nlh) - sizeof(*ev);
-
 		if ((ev->u.send_pdu.hdr_size > pdu_len) ||
 		    (ev->u.send_pdu.data_size > (pdu_len - ev->u.send_pdu.hdr_size))) {
 			err = -EINVAL;
@@ -3796,6 +3931,7 @@
 	struct iscsi_internal *priv;
 	struct iscsi_cls_session *session;
 	struct iscsi_endpoint *ep = NULL;
+	u32 rlen;
 
 	if (!netlink_capable(skb, CAP_SYS_ADMIN))
 		return -EPERM;
@@ -3815,6 +3951,13 @@
 
 	portid = NETLINK_CB(skb).portid;
 
+	/*
+	 * Even though the remaining payload may not be regarded as nlattr,
+	 * (like address or something else), calculate the remaining length
+	 * here to ease following length checks.
+	 */
+	rlen = nlmsg_attrlen(nlh, sizeof(*ev));
+
 	switch (nlh->nlmsg_type) {
 	case ISCSI_UEVENT_CREATE_SESSION:
 		err = iscsi_if_create_session(priv, ep, ev,
@@ -3872,7 +4015,7 @@
 			err = -EINVAL;
 		break;
 	case ISCSI_UEVENT_SET_PARAM:
-		err = iscsi_set_param(transport, ev);
+		err = iscsi_if_set_param(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_CREATE_CONN:
 	case ISCSI_UEVENT_DESTROY_CONN:
@@ -3880,7 +4023,7 @@
 	case ISCSI_UEVENT_START_CONN:
 	case ISCSI_UEVENT_BIND_CONN:
 	case ISCSI_UEVENT_SEND_PDU:
-		err = iscsi_if_transport_conn(transport, nlh);
+		err = iscsi_if_transport_conn(transport, nlh, rlen);
 		break;
 	case ISCSI_UEVENT_GET_STATS:
 		err = iscsi_if_get_stats(transport, nlh);
@@ -3889,23 +4032,22 @@
 	case ISCSI_UEVENT_TRANSPORT_EP_POLL:
 	case ISCSI_UEVENT_TRANSPORT_EP_DISCONNECT:
 	case ISCSI_UEVENT_TRANSPORT_EP_CONNECT_THROUGH_HOST:
-		err = iscsi_if_transport_ep(transport, ev, nlh->nlmsg_type);
+		err = iscsi_if_transport_ep(transport, ev, nlh->nlmsg_type, rlen);
 		break;
 	case ISCSI_UEVENT_TGT_DSCVR:
-		err = iscsi_tgt_dscvr(transport, ev);
+		err = iscsi_tgt_dscvr(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_SET_HOST_PARAM:
-		err = iscsi_set_host_param(transport, ev);
+		err = iscsi_set_host_param(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_PATH_UPDATE:
-		err = iscsi_set_path(transport, ev);
+		err = iscsi_set_path(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_SET_IFACE_PARAMS:
-		err = iscsi_set_iface_params(transport, ev,
-					     nlmsg_attrlen(nlh, sizeof(*ev)));
+		err = iscsi_set_iface_params(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_PING:
-		err = iscsi_send_ping(transport, ev);
+		err = iscsi_send_ping(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_GET_CHAP:
 		err = iscsi_get_chap(transport, nlh);
@@ -3914,13 +4056,10 @@
 		err = iscsi_delete_chap(transport, ev);
 		break;
 	case ISCSI_UEVENT_SET_FLASHNODE_PARAMS:
-		err = iscsi_set_flashnode_param(transport, ev,
-						nlmsg_attrlen(nlh,
-							      sizeof(*ev)));
+		err = iscsi_set_flashnode_param(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_NEW_FLASHNODE:
-		err = iscsi_new_flashnode(transport, ev,
-					  nlmsg_attrlen(nlh, sizeof(*ev)));
+		err = iscsi_new_flashnode(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_DEL_FLASHNODE:
 		err = iscsi_del_flashnode(transport, ev);
@@ -3935,8 +4074,7 @@
 		err = iscsi_logout_flashnode_sid(transport, ev);
 		break;
 	case ISCSI_UEVENT_SET_CHAP:
-		err = iscsi_set_chap(transport, ev,
-				     nlmsg_attrlen(nlh, sizeof(*ev)));
+		err = iscsi_set_chap(transport, ev, rlen);
 		break;
 	case ISCSI_UEVENT_GET_HOST_STATS:
 		err = iscsi_get_host_stats(transport, nlh);
@@ -3986,7 +4124,7 @@
 		}
 		do {
 			/*
-			 * special case for GET_STATS:
+			 * special case for GET_STATS, GET_CHAP and GET_HOST_STATS:
 			 * on success - sending reply and stats from
 			 * inside of if_recv_msg(),
 			 * on error - fall through.
@@ -3995,6 +4133,8 @@
 				break;
 			if (ev->type == ISCSI_UEVENT_GET_CHAP && !err)
 				break;
+			if (ev->type == ISCSI_UEVENT_GET_HOST_STATS && !err)
+				break;
 			err = iscsi_if_send_reply(portid, nlh->nlmsg_type,
 						  ev, sizeof(*ev));
 			if (err == -EAGAIN && --retries < 0) {
@@ -4070,10 +4210,11 @@
 {
 	struct iscsi_cls_conn *conn = iscsi_dev_to_conn(dev->parent);
 	const char *state = "unknown";
+	int conn_state = READ_ONCE(conn->state);
 
-	if (conn->state >= 0 &&
-	    conn->state < ARRAY_SIZE(connection_state_names))
-		state = connection_state_names[conn->state];
+	if (conn_state >= 0 &&
+	    conn_state < ARRAY_SIZE(connection_state_names))
+		state = connection_state_names[conn_state];
 
 	return sysfs_emit(buf, "%s\n", state);
 }
@@ -4299,6 +4440,19 @@
 iscsi_session_attr(discovery_parent_type, ISCSI_PARAM_DISCOVERY_PARENT_TYPE, 0);
 
 static ssize_t
+show_priv_session_target_state(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct iscsi_cls_session *session = iscsi_dev_to_session(dev->parent);
+
+	return sysfs_emit(buf, "%s\n",
+			iscsi_session_target_state_name[session->target_state]);
+}
+
+static ISCSI_CLASS_ATTR(priv_sess, target_state, S_IRUGO,
+			show_priv_session_target_state, NULL);
+
+static ssize_t
 show_priv_session_state(struct device *dev, struct device_attribute *attr,
 			char *buf)
 {
@@ -4400,6 +4554,7 @@
 	&dev_attr_sess_boot_target.attr,
 	&dev_attr_priv_sess_recovery_tmo.attr,
 	&dev_attr_priv_sess_state.attr,
+	&dev_attr_priv_sess_target_state.attr,
 	&dev_attr_priv_sess_creator.attr,
 	&dev_attr_sess_chap_out_idx.attr,
 	&dev_attr_sess_chap_in_idx.attr,
@@ -4513,6 +4668,8 @@
 		return S_IRUGO | S_IWUSR;
 	else if (attr == &dev_attr_priv_sess_state.attr)
 		return S_IRUGO;
+	else if (attr == &dev_attr_priv_sess_target_state.attr)
+		return S_IRUGO;
 	else if (attr == &dev_attr_priv_sess_creator.attr)
 		return S_IRUGO;
 	else if (attr == &dev_attr_priv_sess_target_id.attr)
@@ -4746,7 +4903,7 @@
 	dev_set_name(&priv->dev, "%s", tt->name);
 	err = device_register(&priv->dev);
 	if (err)
-		goto free_priv;
+		goto put_dev;
 
 	err = sysfs_create_group(&priv->dev.kobj, &iscsi_transport_group);
 	if (err)
@@ -4781,8 +4938,8 @@
 unregister_dev:
 	device_unregister(&priv->dev);
 	return NULL;
-free_priv:
-	kfree(priv);
+put_dev:
+	put_device(&priv->dev);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(iscsi_register_transport);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_transport_sas.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_transport_sas.c
@@ -410,6 +410,35 @@
 }
 EXPORT_SYMBOL_GPL(sas_is_tlr_enabled);
 
+/**
+ * sas_ata_ncq_prio_supported - Check for ATA NCQ command priority support
+ * @sdev: SCSI device
+ *
+ * Check if an ATA device supports NCQ priority using VPD page 89h (ATA
+ * Information). Since this VPD page is implemented only for ATA devices,
+ * this function always returns false for SCSI devices.
+ */
+bool sas_ata_ncq_prio_supported(struct scsi_device *sdev)
+{
+	unsigned char *buf;
+	bool ncq_prio_supported = false;
+
+	if (!scsi_device_supports_vpd(sdev))
+		return false;
+
+	buf = kmalloc(SCSI_VPD_PG_LEN, GFP_KERNEL);
+	if (!buf)
+		return false;
+
+	if (!scsi_get_vpd_page(sdev, 0x89, buf, SCSI_VPD_PG_LEN))
+		ncq_prio_supported = (buf[213] >> 4) & 1;
+
+	kfree(buf);
+
+	return ncq_prio_supported;
+}
+EXPORT_SYMBOL_GPL(sas_ata_ncq_prio_supported);
+
 /*
  * SAS Phy attributes
  */
@@ -716,12 +745,17 @@
 	int error;
 
 	error = device_add(&phy->dev);
-	if (!error) {
-		transport_add_device(&phy->dev);
-		transport_configure_device(&phy->dev);
+	if (error)
+		return error;
+
+	error = transport_add_device(&phy->dev);
+	if (error) {
+		device_del(&phy->dev);
+		return error;
 	}
+	transport_configure_device(&phy->dev);
 
-	return error;
+	return 0;
 }
 EXPORT_SYMBOL(sas_phy_add);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/scsi_transport_spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/scsi_transport_spi.c
@@ -677,10 +677,10 @@
 	for (r = 0; r < retries; r++) {
 		result = spi_execute(sdev, spi_write_buffer, DMA_TO_DEVICE,
 				     buffer, len, &sshdr);
-		if(result || !scsi_device_online(sdev)) {
+		if (result || !scsi_device_online(sdev)) {
 
 			scsi_device_set_state(sdev, SDEV_QUIESCE);
-			if (scsi_sense_valid(&sshdr)
+			if (result > 0 && scsi_sense_valid(&sshdr)
 			    && sshdr.sense_key == ILLEGAL_REQUEST
 			    /* INVALID FIELD IN CDB */
 			    && sshdr.asc == 0x24 && sshdr.ascq == 0x00)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sd.c
@@ -48,6 +48,7 @@
 #include <linux/blkpg.h>
 #include <linux/blk-pm.h>
 #include <linux/delay.h>
+#include <linux/major.h>
 #include <linux/mutex.h>
 #include <linux/string_helpers.h>
 #include <linux/async.h>
@@ -1071,6 +1072,7 @@
 	struct bio *bio = rq->bio;
 	u64 lba = sectors_to_logical(sdp, blk_rq_pos(rq));
 	u32 nr_blocks = sectors_to_logical(sdp, blk_rq_sectors(rq));
+	unsigned int nr_bytes = blk_rq_bytes(rq);
 	blk_status_t ret;
 
 	if (sdkp->device->no_write_same)
@@ -1107,7 +1109,7 @@
 	 */
 	rq->__data_len = sdp->sector_size;
 	ret = scsi_alloc_sgtables(cmd);
-	rq->__data_len = blk_rq_bytes(rq);
+	rq->__data_len = nr_bytes;
 
 	return ret;
 }
@@ -2607,6 +2609,13 @@
 		 unsigned char *buffer, int len, struct scsi_mode_data *data,
 		 struct scsi_sense_hdr *sshdr)
 {
+	/*
+	 * If we must use MODE SENSE(10), make sure that the buffer length
+	 * is at least 8 bytes so that the mode sense header fits.
+	 */
+	if (sdkp->device->use_10_for_ms && len < 8)
+		len = 8;
+
 	return scsi_mode_sense(sdkp->device, dbd, modepage, buffer, len,
 			       SD_TIMEOUT, sdkp->max_retries, data,
 			       sshdr);
@@ -3472,7 +3481,6 @@
  out_put:
 	put_disk(gd);
  out_free:
-	sd_zbc_release_disk(sdkp);
 	kfree(sdkp);
  out:
 	scsi_autopm_put_device(sdp);
@@ -3620,7 +3628,8 @@
 		return 0;
 
 	if (sdkp->WCE && sdkp->media_present) {
-		sd_printk(KERN_NOTICE, sdkp, "Synchronizing SCSI cache\n");
+		if (!sdkp->device->silence_suspend)
+			sd_printk(KERN_NOTICE, sdkp, "Synchronizing SCSI cache\n");
 		ret = sd_sync_cache(sdkp, &sshdr);
 
 		if (ret) {
@@ -3642,7 +3651,8 @@
 	}
 
 	if (sdkp->device->manage_start_stop) {
-		sd_printk(KERN_NOTICE, sdkp, "Stopping disk\n");
+		if (!sdkp->device->silence_suspend)
+			sd_printk(KERN_NOTICE, sdkp, "Stopping disk\n");
 		/* an error is not worth aborting a system sleep */
 		ret = sd_start_stop_device(sdkp, 0);
 		if (ignore_stop_errors)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sd_zbc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sd_zbc.c
@@ -168,8 +168,7 @@
 	bufsize = min_t(size_t, bufsize, queue_max_segments(q) << PAGE_SHIFT);
 
 	while (bufsize >= SECTOR_SIZE) {
-		buf = __vmalloc(bufsize,
-				GFP_KERNEL | __GFP_ZERO | __GFP_NORETRY);
+		buf = kvzalloc(bufsize, GFP_KERNEL | __GFP_NORETRY);
 		if (buf) {
 			*buflen = bufsize;
 			return buf;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ses.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ses.c
@@ -433,8 +433,8 @@
 }
 #endif  /*  0  */
 
-static void ses_process_descriptor(struct enclosure_component *ecomp,
-				   unsigned char *desc)
+static int ses_process_descriptor(struct enclosure_component *ecomp,
+				   unsigned char *desc, int max_desc_len)
 {
 	int eip = desc[0] & 0x10;
 	int invalid = desc[0] & 0x80;
@@ -445,22 +445,32 @@
 	unsigned char *d;
 
 	if (invalid)
-		return;
+		return 0;
 
 	switch (proto) {
 	case SCSI_PROTOCOL_FCP:
 		if (eip) {
+			if (max_desc_len <= 7)
+				return 1;
 			d = desc + 4;
 			slot = d[3];
 		}
 		break;
 	case SCSI_PROTOCOL_SAS:
+
 		if (eip) {
+			if (max_desc_len <= 27)
+				return 1;
 			d = desc + 4;
 			slot = d[3];
 			d = desc + 8;
-		} else
+		} else {
+			if (max_desc_len <= 23)
+				return 1;
 			d = desc + 4;
+		}
+
+
 		/* only take the phy0 addr */
 		addr = (u64)d[12] << 56 |
 			(u64)d[13] << 48 |
@@ -477,6 +487,8 @@
 	}
 	ecomp->slot = slot;
 	scomp->addr = addr;
+
+	return 0;
 }
 
 struct efd {
@@ -491,9 +503,6 @@
 	int i;
 	struct ses_component *scomp;
 
-	if (!edev->component[0].scratch)
-		return 0;
-
 	for (i = 0; i < edev->components; i++) {
 		scomp = edev->component[i].scratch;
 		if (scomp->addr != efd->addr)
@@ -549,7 +558,7 @@
 		/* skip past overall descriptor */
 		desc_ptr += len + 4;
 	}
-	if (ses_dev->page10)
+	if (ses_dev->page10 && ses_dev->page10_len > 9)
 		addl_desc_ptr = ses_dev->page10 + 8;
 	type_ptr = ses_dev->page1_types;
 	components = 0;
@@ -557,17 +566,22 @@
 		for (j = 0; j < type_ptr[1]; j++) {
 			char *name = NULL;
 			struct enclosure_component *ecomp;
+			int max_desc_len;
 
 			if (desc_ptr) {
-				if (desc_ptr >= buf + page7_len) {
+				if (desc_ptr + 3 >= buf + page7_len) {
 					desc_ptr = NULL;
 				} else {
 					len = (desc_ptr[2] << 8) + desc_ptr[3];
 					desc_ptr += 4;
-					/* Add trailing zero - pushes into
-					 * reserved space */
-					desc_ptr[len] = '\0';
-					name = desc_ptr;
+					if (desc_ptr + len > buf + page7_len)
+						desc_ptr = NULL;
+					else {
+						/* Add trailing zero - pushes into
+						 * reserved space */
+						desc_ptr[len] = '\0';
+						name = desc_ptr;
+					}
 				}
 			}
 			if (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE ||
@@ -579,14 +593,20 @@
 						components++,
 						type_ptr[0],
 						name);
-				else
+				else if (components < edev->components)
 					ecomp = &edev->component[components++];
+				else
+					ecomp = ERR_PTR(-EINVAL);
 
 				if (!IS_ERR(ecomp)) {
-					if (addl_desc_ptr)
-						ses_process_descriptor(
-							ecomp,
-							addl_desc_ptr);
+					if (addl_desc_ptr) {
+						max_desc_len = ses_dev->page10_len -
+						    (addl_desc_ptr - ses_dev->page10);
+						if (ses_process_descriptor(ecomp,
+						    addl_desc_ptr,
+						    max_desc_len))
+							addl_desc_ptr = NULL;
+					}
 					if (create)
 						enclosure_component_register(
 							ecomp);
@@ -603,9 +623,11 @@
 			     /* these elements are optional */
 			     type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_TARGET_PORT ||
 			     type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_INITIATOR_PORT ||
-			     type_ptr[0] == ENCLOSURE_COMPONENT_CONTROLLER_ELECTRONICS))
+			     type_ptr[0] == ENCLOSURE_COMPONENT_CONTROLLER_ELECTRONICS)) {
 				addl_desc_ptr += addl_desc_ptr[1] + 2;
-
+				if (addl_desc_ptr + 1 >= ses_dev->page10 + ses_dev->page10_len)
+					addl_desc_ptr = NULL;
+			}
 		}
 	}
 	kfree(buf);
@@ -704,6 +726,7 @@
 		    type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE)
 			components += type_ptr[1];
 	}
+
 	ses_dev->page1 = buf;
 	ses_dev->page1_len = len;
 	buf = NULL;
@@ -745,9 +768,11 @@
 		buf = NULL;
 	}
 page2_not_supported:
-	scomp = kcalloc(components, sizeof(struct ses_component), GFP_KERNEL);
-	if (!scomp)
-		goto err_free;
+	if (components > 0) {
+		scomp = kcalloc(components, sizeof(struct ses_component), GFP_KERNEL);
+		if (!scomp)
+			goto err_free;
+	}
 
 	edev = enclosure_register(cdev->parent, dev_name(&sdev->sdev_gendev),
 				  components, &ses_enclosure_callbacks);
@@ -827,7 +852,8 @@
 	kfree(ses_dev->page2);
 	kfree(ses_dev);
 
-	kfree(edev->component[0].scratch);
+	if (edev->components)
+		kfree(edev->component[0].scratch);
 
 	put_device(&edev->edev);
 	enclosure_unregister(edev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sg.c
@@ -31,6 +31,7 @@
 #include <linux/errno.h>
 #include <linux/mtio.h>
 #include <linux/ioctl.h>
+#include <linux/major.h>
 #include <linux/slab.h>
 #include <linux/fcntl.h>
 #include <linux/init.h>
@@ -190,7 +191,7 @@
 static void sg_unlink_reserve(Sg_fd * sfp, Sg_request * srp);
 static Sg_fd *sg_add_sfp(Sg_device * sdp);
 static void sg_remove_sfp(struct kref *);
-static Sg_request *sg_get_rq_mark(Sg_fd * sfp, int pack_id);
+static Sg_request *sg_get_rq_mark(Sg_fd * sfp, int pack_id, bool *busy);
 static Sg_request *sg_add_request(Sg_fd * sfp);
 static int sg_remove_request(Sg_fd * sfp, Sg_request * srp);
 static Sg_device *sg_get_dev(int dev);
@@ -390,7 +391,6 @@
 
 	mutex_lock(&sdp->open_rel_lock);
 	scsi_autopm_put_device(sdp->device);
-	kref_put(&sfp->f_ref, sg_remove_sfp);
 	sdp->open_cnt--;
 
 	/* possibly many open()s waiting on exlude clearing, start many;
@@ -402,6 +402,7 @@
 		wake_up_interruptible(&sdp->open_wait);
 	}
 	mutex_unlock(&sdp->open_rel_lock);
+	kref_put(&sfp->f_ref, sg_remove_sfp);
 	return 0;
 }
 
@@ -444,6 +445,7 @@
 	Sg_fd *sfp;
 	Sg_request *srp;
 	int req_pack_id = -1;
+	bool busy;
 	sg_io_hdr_t *hp;
 	struct sg_header *old_hdr;
 	int retval;
@@ -466,20 +468,16 @@
 	if (retval)
 		return retval;
 
-	srp = sg_get_rq_mark(sfp, req_pack_id);
+	srp = sg_get_rq_mark(sfp, req_pack_id, &busy);
 	if (!srp) {		/* now wait on packet to arrive */
-		if (atomic_read(&sdp->detaching))
-			return -ENODEV;
 		if (filp->f_flags & O_NONBLOCK)
 			return -EAGAIN;
 		retval = wait_event_interruptible(sfp->read_wait,
-			(atomic_read(&sdp->detaching) ||
-			(srp = sg_get_rq_mark(sfp, req_pack_id))));
-		if (atomic_read(&sdp->detaching))
-			return -ENODEV;
-		if (retval)
-			/* -ERESTARTSYS as signal hit process */
-			return retval;
+			((srp = sg_get_rq_mark(sfp, req_pack_id, &busy)) ||
+			(!busy && atomic_read(&sdp->detaching))));
+		if (!srp)
+			/* signal or detaching */
+			return retval ? retval : -ENODEV;
 	}
 	if (srp->header.interface_id != '\0')
 		return sg_new_read(sfp, buf, count, srp);
@@ -940,9 +938,7 @@
 		if (result < 0)
 			return result;
 		result = wait_event_interruptible(sfp->read_wait,
-			(srp_done(sfp, srp) || atomic_read(&sdp->detaching)));
-		if (atomic_read(&sdp->detaching))
-			return -ENODEV;
+			srp_done(sfp, srp));
 		write_lock_irq(&sfp->rq_list_lock);
 		if (srp->done) {
 			srp->done = 2;
@@ -2055,19 +2051,28 @@
 }
 
 static Sg_request *
-sg_get_rq_mark(Sg_fd * sfp, int pack_id)
+sg_get_rq_mark(Sg_fd * sfp, int pack_id, bool *busy)
 {
 	Sg_request *resp;
 	unsigned long iflags;
 
+	*busy = false;
 	write_lock_irqsave(&sfp->rq_list_lock, iflags);
 	list_for_each_entry(resp, &sfp->rq_list, entry) {
-		/* look for requests that are ready + not SG_IO owned */
-		if ((1 == resp->done) && (!resp->sg_io_owned) &&
+		/* look for requests that are not SG_IO owned */
+		if ((!resp->sg_io_owned) &&
 		    ((-1 == pack_id) || (resp->header.pack_id == pack_id))) {
-			resp->done = 2;	/* guard against other readers */
-			write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
-			return resp;
+			switch (resp->done) {
+			case 0: /* request active */
+				*busy = true;
+				break;
+			case 1: /* request done; response ready to return */
+				resp->done = 2;	/* guard against other readers */
+				write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
+				return resp;
+			case 2: /* response already being returned */
+				break;
+			}
 		}
 	}
 	write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
@@ -2121,6 +2126,15 @@
 		res = 1;
 	}
 	write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
+
+	/*
+	 * If the device is detaching, wakeup any readers in case we just
+	 * removed the last response, which would leave nothing for them to
+	 * return other than -ENODEV.
+	 */
+	if (unlikely(atomic_read(&sfp->parentdp->detaching)))
+		wake_up_interruptible_all(&sfp->read_wait);
+
 	return res;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/smartpqi/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/smartpqi/Kconfig
@@ -1,7 +1,7 @@
 #
 # Kernel configuration file for the SMARTPQI
 #
-# Copyright (c) 2019-2021 Microchip Technology Inc. and its subsidiaries
+# Copyright (c) 2019-2022 Microchip Technology Inc. and its subsidiaries
 # Copyright (c) 2017-2018 Microsemi Corporation
 # Copyright (c) 2016 Microsemi Corporation
 # Copyright (c) 2016 PMC-Sierra, Inc.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/smartpqi/smartpqi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/smartpqi/smartpqi.h
@@ -1,7 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
  *    driver for Microchip PQI-based storage controllers
- *    Copyright (c) 2019-2021 Microchip Technology Inc. and its subsidiaries
+ *    Copyright (c) 2019-2022 Microchip Technology Inc. and its subsidiaries
  *    Copyright (c) 2016-2018 Microsemi Corporation
  *    Copyright (c) 2016 PMC-Sierra, Inc.
  *
@@ -82,9 +82,11 @@
 	__le32  sis_product_identifier;			/* B4h */
 	u8	reserved5[0xbc - (0xb4 + sizeof(__le32))];
 	__le32	sis_firmware_status;			/* BCh */
-	u8	reserved6[0x1000 - (0xbc + sizeof(__le32))];
+	u8	reserved6[0xcc - (0xbc + sizeof(__le32))];
+	__le32	sis_ctrl_shutdown_reason_code;		/* CCh */
+	u8	reserved7[0x1000 - (0xcc + sizeof(__le32))];
 	__le32	sis_mailbox[8];				/* 1000h */
-	u8	reserved7[0x4000 - (0x1000 + (sizeof(__le32) * 8))];
+	u8	reserved8[0x4000 - (0x1000 + (sizeof(__le32) * 8))];
 	/*
 	 * The PQI spec states that the PQI registers should be at
 	 * offset 0 from the PCIe BAR 0.  However, we can't map
@@ -94,14 +96,23 @@
 	struct pqi_device_registers pqi_registers;	/* 4000h */
 };
 
-#if ((HZ) < 1000)
-#define PQI_HZ  1000
-#else
-#define PQI_HZ  (HZ)
-#endif
-
 #define PQI_DEVICE_REGISTERS_OFFSET	0x4000
 
+/* shutdown reasons for taking the controller offline */
+enum pqi_ctrl_shutdown_reason {
+	PQI_IQ_NOT_DRAINED_TIMEOUT = 1,
+	PQI_LUN_RESET_TIMEOUT = 2,
+	PQI_IO_PENDING_POST_LUN_RESET_TIMEOUT = 3,
+	PQI_NO_HEARTBEAT = 4,
+	PQI_FIRMWARE_KERNEL_NOT_UP = 5,
+	PQI_OFA_RESPONSE_TIMEOUT = 6,
+	PQI_INVALID_REQ_ID = 7,
+	PQI_UNMATCHED_REQ_ID = 8,
+	PQI_IO_PI_OUT_OF_RANGE = 9,
+	PQI_EVENT_PI_OUT_OF_RANGE = 10,
+	PQI_UNEXPECTED_IU_TYPE = 11
+};
+
 enum pqi_io_path {
 	RAID_PATH = 0,
 	AIO_PATH = 1
@@ -282,7 +293,8 @@
 	u8	additional_cdb_bytes_usage : 3;
 	u8	reserved5 : 3;
 	u8	cdb[16];
-	u8	reserved6[12];
+	u8	reserved6[11];
+	u8	ml_device_lun_number;
 	__le32	timeout;
 	struct pqi_sg_descriptor sg_descriptors[PQI_MAX_EMBEDDED_SG_DESCRIPTORS];
 };
@@ -456,7 +468,8 @@
 	struct pqi_iu_header header;
 	__le16	request_id;
 	__le16	nexus_id;
-	u8	reserved[2];
+	u8	reserved;
+	u8	ml_device_lun_number;
 	__le16  timeout;
 	u8	lun_number[8];
 	__le16	protocol_specific;
@@ -697,6 +710,7 @@
 #define SOP_TMF_COMPLETE		0x0
 #define SOP_TMF_REJECTED		0x4
 #define SOP_TMF_FUNCTION_SUCCEEDED	0x8
+#define SOP_RC_INCORRECT_LOGICAL_UNIT	0x9
 
 /* additional CDB bytes usage field codes */
 #define SOP_ADDITIONAL_CDB_BYTES_0	0	/* 16-byte CDB */
@@ -850,7 +864,10 @@
 #define PQI_FIRMWARE_FEATURE_TMF_IU_TIMEOUT			14
 #define PQI_FIRMWARE_FEATURE_RAID_BYPASS_ON_ENCRYPTED_NVME	15
 #define PQI_FIRMWARE_FEATURE_UNIQUE_WWID_IN_REPORT_PHYS_LUN	16
-#define PQI_FIRMWARE_FEATURE_MAXIMUM				16
+#define PQI_FIRMWARE_FEATURE_FW_TRIAGE				17
+#define PQI_FIRMWARE_FEATURE_RPL_EXTENDED_FORMAT_4_5		18
+#define PQI_FIRMWARE_FEATURE_MULTI_LUN_DEVICE_SUPPORT           21
+#define PQI_FIRMWARE_FEATURE_MAXIMUM                            21
 
 struct pqi_config_table_debug {
 	struct pqi_config_table_section_header header;
@@ -905,7 +922,8 @@
 #define PQI_MAX_TRANSFER_SIZE			(1024U * 1024U)
 #define PQI_MAX_TRANSFER_SIZE_KDUMP		(512 * 1024U)
 
-#define RAID_MAP_MAX_ENTRIES		1024
+#define RAID_MAP_MAX_ENTRIES			1024
+#define RAID_MAP_MAX_DATA_DISKS_PER_ROW		128
 
 #define PQI_PHYSICAL_DEVICE_BUS		0
 #define PQI_RAID_VOLUME_BUS		1
@@ -925,19 +943,21 @@
 #define CISS_REPORT_LOG_FLAG_QUEUE_DEPTH	(1 << 5)
 #define CISS_REPORT_LOG_FLAG_DRIVE_TYPE_MIX	(1 << 6)
 
-#define CISS_REPORT_PHYS_FLAG_OTHER		(1 << 1)
+#define CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_2		0x2
+#define CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_4		0x4
+#define CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_MASK	0xf
 
-struct report_log_lun_extended_entry {
+struct report_log_lun {
 	u8	lunid[8];
 	u8	volume_id[16];
 };
 
-struct report_log_lun_extended {
+struct report_log_lun_list {
 	struct report_lun_header header;
-	struct report_log_lun_extended_entry lun_entries[1];
+	struct report_log_lun lun_entries[1];
 };
 
-struct report_phys_lun_extended_entry {
+struct report_phys_lun_8byte_wwid {
 	u8	lunid[8];
 	__be64	wwid;
 	u8	device_type;
@@ -947,12 +967,27 @@
 	u32	aio_handle;
 };
 
+struct report_phys_lun_16byte_wwid {
+	u8	lunid[8];
+	u8	wwid[16];
+	u8	device_type;
+	u8	device_flags;
+	u8	lun_count;	/* number of LUNs in a multi-LUN device */
+	u8	redundant_paths;
+	u32	aio_handle;
+};
+
 /* for device_flags field of struct report_phys_lun_extended_entry */
 #define CISS_REPORT_PHYS_DEV_FLAG_AIO_ENABLED	0x8
 
-struct report_phys_lun_extended {
+struct report_phys_lun_8byte_wwid_list {
+	struct report_lun_header header;
+	struct report_phys_lun_8byte_wwid lun_entries[1];
+};
+
+struct report_phys_lun_16byte_wwid_list {
 	struct report_lun_header header;
-	struct report_phys_lun_extended_entry lun_entries[1];
+	struct report_phys_lun_16byte_wwid lun_entries[1];
 };
 
 struct raid_map_disk_data {
@@ -1050,8 +1085,10 @@
 	u32	last_accessed;
 };
 
+#define PQI_MAX_LUNS_PER_DEVICE         256
+
 struct pqi_scsi_dev {
-	int	devtype;		/* as reported by INQUIRY commmand */
+	int	devtype;		/* as reported by INQUIRY command */
 	u8	device_type;		/* as reported by */
 					/* BMIC_IDENTIFY_PHYSICAL_DEVICE */
 					/* only valid for devtype = TYPE_DISK */
@@ -1059,7 +1096,7 @@
 	int	target;
 	int	lun;
 	u8	scsi3addr[8];
-	__be64	wwid;
+	u8	wwid[16];
 	u8	volume_id[16];
 	u8	is_physical_device : 1;
 	u8	is_external_raid_device : 1;
@@ -1070,6 +1107,7 @@
 	u8	keep_device : 1;
 	u8	volume_offline : 1;
 	u8	rescan : 1;
+	u8	ignore_device : 1;
 	bool	aio_enabled;		/* only valid for physical disks */
 	bool	in_remove;
 	bool	device_offline;
@@ -1090,9 +1128,12 @@
 	u8	box[8];
 	u16	phys_connector[8];
 	u8	phy_id;
+	u8	ncq_prio_enable;
+	u8	ncq_prio_support;
+	u8	lun_count;
 	bool	raid_bypass_configured;	/* RAID bypass configured */
 	bool	raid_bypass_enabled;	/* RAID bypass enabled */
-	u32	next_bypass_group;
+	u32	next_bypass_group[RAID_MAP_MAX_DATA_DISKS_PER_ROW];
 	struct raid_map *raid_map;	/* RAID bypass map */
 	u32	max_transfer_encrypted;
 
@@ -1105,9 +1146,8 @@
 	struct list_head delete_list_entry;
 
 	struct pqi_stream_data stream_data[NUM_STREAMS_PER_LUN];
-	atomic_t scsi_cmds_outstanding;
+	atomic_t scsi_cmds_outstanding[PQI_MAX_LUNS_PER_DEVICE];
 	atomic_t raid_bypass_cnt;
-	u8	page_83_identifier[16];
 };
 
 /* VPD inquiry pages */
@@ -1229,6 +1269,12 @@
 #define PQI_CTRL_PRODUCT_REVISION_A	0
 #define PQI_CTRL_PRODUCT_REVISION_B	1
 
+enum pqi_ctrl_removal_state {
+	PQI_CTRL_PRESENT = 0,
+	PQI_CTRL_GRACEFUL_REMOVAL,
+	PQI_CTRL_SURPRISE_REMOVAL
+};
+
 struct pqi_ctrl_info {
 	unsigned int	ctrl_id;
 	struct pci_dev	*pci_dev;
@@ -1261,7 +1307,6 @@
 	dma_addr_t	error_buffer_dma_handle;
 	size_t		sg_chain_buffer_length;
 	unsigned int	num_queue_groups;
-	u16		max_hw_queue_index;
 	u16		num_elements_per_iq;
 	u16		num_elements_per_oq;
 	u16		max_inbound_iu_length_per_firmware;
@@ -1289,6 +1334,7 @@
 	bool		controller_online;
 	bool		block_requests;
 	bool		scan_blocked;
+	u8		logical_volume_rescan_needed : 1;
 	u8		inbound_spanning_supported : 1;
 	u8		outbound_spanning_supported : 1;
 	u8		pqi_mode_enabled : 1;
@@ -1296,13 +1342,15 @@
 	u8		soft_reset_handshake_supported : 1;
 	u8		raid_iu_timeout_supported : 1;
 	u8		tmf_iu_timeout_supported : 1;
-	u8		unique_wwid_in_report_phys_lun_supported : 1;
+	u8		firmware_triage_supported : 1;
+	u8		rpl_extended_format_4_5_supported : 1;
+	u8		multi_lun_device_supported : 1;
 	u8		enable_r1_writes : 1;
 	u8		enable_r5_writes : 1;
 	u8		enable_r6_writes : 1;
 	u8		lv_drive_type_mix_valid : 1;
 	u8		enable_stream_detection : 1;
-
+	u8		disable_managed_interrupts : 1;
 	u8		ciss_report_log_flags;
 	u32		max_transfer_encrypted_sas_sata;
 	u32		max_transfer_encrypted_nvme;
@@ -1320,8 +1368,6 @@
 	u64		sas_address;
 
 	struct pqi_io_request *io_request_pool;
-	u16		next_io_request_slot;
-
 	struct pqi_event events[PQI_NUM_SUPPORTED_EVENTS];
 	struct work_struct event_work;
 
@@ -1346,6 +1392,7 @@
 	struct work_struct ofa_quiesce_work;
 	u32		ofa_bytes_requested;
 	u16		ofa_cancel_reason;
+	enum pqi_ctrl_removal_state ctrl_removal_state;
 };
 
 enum pqi_ctrl_mode {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/smartpqi/smartpqi_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/smartpqi/smartpqi_init.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
  *    driver for Microchip PQI-based storage controllers
- *    Copyright (c) 2019-2021 Microchip Technology Inc. and its subsidiaries
+ *    Copyright (c) 2019-2022 Microchip Technology Inc. and its subsidiaries
  *    Copyright (c) 2016-2018 Microsemi Corporation
  *    Copyright (c) 2016 PMC-Sierra, Inc.
  *
@@ -33,11 +33,11 @@
 #define BUILD_TIMESTAMP
 #endif
 
-#define DRIVER_VERSION		"2.1.10-020"
+#define DRIVER_VERSION		"2.1.20-035"
 #define DRIVER_MAJOR		2
 #define DRIVER_MINOR		1
-#define DRIVER_RELEASE		10
-#define DRIVER_REVISION		20
+#define DRIVER_RELEASE		20
+#define DRIVER_REVISION		35
 
 #define DRIVER_NAME		"Microchip SmartPQI Driver (v" \
 				DRIVER_VERSION BUILD_TIMESTAMP ")"
@@ -54,7 +54,18 @@
 MODULE_VERSION(DRIVER_VERSION);
 MODULE_LICENSE("GPL");
 
-static void pqi_take_ctrl_offline(struct pqi_ctrl_info *ctrl_info);
+struct pqi_cmd_priv {
+	int this_residual;
+};
+
+static struct pqi_cmd_priv *pqi_cmd_priv(struct scsi_cmnd *cmd)
+{
+	return scsi_cmd_priv(cmd);
+}
+
+static void pqi_verify_structures(void);
+static void pqi_take_ctrl_offline(struct pqi_ctrl_info *ctrl_info,
+	enum pqi_ctrl_shutdown_reason ctrl_shutdown_reason);
 static void pqi_ctrl_offline_worker(struct work_struct *work);
 static int pqi_scan_scsi_devices(struct pqi_ctrl_info *ctrl_info);
 static void pqi_scan_start(struct Scsi_Host *shost);
@@ -67,7 +78,7 @@
 static int pqi_aio_submit_io(struct pqi_ctrl_info *ctrl_info,
 	struct scsi_cmnd *scmd, u32 aio_handle, u8 *cdb,
 	unsigned int cdb_length, struct pqi_queue_group *queue_group,
-	struct pqi_encryption_info *encryption_info, bool raid_bypass);
+	struct pqi_encryption_info *encryption_info, bool raid_bypass, bool io_high_prio);
 static  int pqi_aio_submit_r1_write_io(struct pqi_ctrl_info *ctrl_info,
 	struct scsi_cmnd *scmd, struct pqi_queue_group *queue_group,
 	struct pqi_encryption_info *encryption_info, struct pqi_scsi_dev *device,
@@ -83,7 +94,8 @@
 static void pqi_ofa_free_host_buffer(struct pqi_ctrl_info *ctrl_info);
 static int pqi_ofa_host_memory_update(struct pqi_ctrl_info *ctrl_info);
 static int pqi_device_wait_for_pending_io(struct pqi_ctrl_info *ctrl_info,
-	struct pqi_scsi_dev *device, unsigned long timeout_msecs);
+	struct pqi_scsi_dev *device, u8 lun, unsigned long timeout_msecs);
+static void pqi_fail_all_outstanding_requests(struct pqi_ctrl_info *ctrl_info);
 
 /* for flags argument to pqi_submit_raid_request_synchronous() */
 #define PQI_SYNC_FLAGS_INTERRUPTABLE	0x1
@@ -163,6 +175,18 @@
 	pqi_hide_vsep, int, 0644);
 MODULE_PARM_DESC(hide_vsep, "Hide the virtual SEP for direct attached drives.");
 
+static int pqi_disable_managed_interrupts;
+module_param_named(disable_managed_interrupts,
+	pqi_disable_managed_interrupts, int, 0644);
+MODULE_PARM_DESC(disable_managed_interrupts,
+	"Disable the kernel automatically assigning SMP affinity to IRQs.");
+
+static unsigned int pqi_ctrl_ready_timeout_secs;
+module_param_named(ctrl_ready_timeout,
+	pqi_ctrl_ready_timeout_secs, uint, 0644);
+MODULE_PARM_DESC(ctrl_ready_timeout,
+	"Timeout in seconds for driver to wait for controller ready.");
+
 static char *raid_levels[] = {
 	"RAID-0",
 	"RAID-4",
@@ -226,7 +250,7 @@
 {
 	if (ctrl_info->controller_online)
 		if (!sis_is_firmware_running(ctrl_info))
-			pqi_take_ctrl_offline(ctrl_info);
+			pqi_take_ctrl_offline(ctrl_info, PQI_FIRMWARE_KERNEL_NOT_UP);
 }
 
 static inline bool pqi_is_hba_lunid(u8 *scsi3addr)
@@ -234,15 +258,46 @@
 	return pqi_scsi3addr_equal(scsi3addr, RAID_CTLR_LUNID);
 }
 
+#define PQI_DRIVER_SCRATCH_PQI_MODE			0x1
+#define PQI_DRIVER_SCRATCH_FW_TRIAGE_SUPPORTED		0x2
+
 static inline enum pqi_ctrl_mode pqi_get_ctrl_mode(struct pqi_ctrl_info *ctrl_info)
 {
-	return sis_read_driver_scratch(ctrl_info);
+	return sis_read_driver_scratch(ctrl_info) & PQI_DRIVER_SCRATCH_PQI_MODE ? PQI_MODE : SIS_MODE;
 }
 
 static inline void pqi_save_ctrl_mode(struct pqi_ctrl_info *ctrl_info,
 	enum pqi_ctrl_mode mode)
 {
-	sis_write_driver_scratch(ctrl_info, mode);
+	u32 driver_scratch;
+
+	driver_scratch = sis_read_driver_scratch(ctrl_info);
+
+	if (mode == PQI_MODE)
+		driver_scratch |= PQI_DRIVER_SCRATCH_PQI_MODE;
+	else
+		driver_scratch &= ~PQI_DRIVER_SCRATCH_PQI_MODE;
+
+	sis_write_driver_scratch(ctrl_info, driver_scratch);
+}
+
+static inline bool pqi_is_fw_triage_supported(struct pqi_ctrl_info *ctrl_info)
+{
+	return (sis_read_driver_scratch(ctrl_info) & PQI_DRIVER_SCRATCH_FW_TRIAGE_SUPPORTED) != 0;
+}
+
+static inline void pqi_save_fw_triage_setting(struct pqi_ctrl_info *ctrl_info, bool is_supported)
+{
+	u32 driver_scratch;
+
+	driver_scratch = sis_read_driver_scratch(ctrl_info);
+
+	if (is_supported)
+		driver_scratch |= PQI_DRIVER_SCRATCH_FW_TRIAGE_SUPPORTED;
+	else
+		driver_scratch &= ~PQI_DRIVER_SCRATCH_FW_TRIAGE_SUPPORTED;
+
+	sis_write_driver_scratch(ctrl_info, driver_scratch);
 }
 
 static inline void pqi_ctrl_block_scan(struct pqi_ctrl_info *ctrl_info)
@@ -344,7 +399,7 @@
 
 	displayed_warning = false;
 	start_jiffies = jiffies;
-	warning_timeout = (PQI_QUIESCE_WARNING_TIMEOUT_SECS * PQI_HZ) + start_jiffies;
+	warning_timeout = (PQI_QUIESCE_WARNING_TIMEOUT_SECS * HZ) + start_jiffies;
 
 	while (atomic_read(&ctrl_info->num_busy_threads) >
 		atomic_read(&ctrl_info->num_blocked_threads)) {
@@ -353,7 +408,7 @@
 				"waiting %u seconds for driver activity to quiesce\n",
 				jiffies_to_msecs(jiffies - start_jiffies) / 1000);
 			displayed_warning = true;
-			warning_timeout = (PQI_QUIESCE_WARNING_TIMEOUT_SECS * PQI_HZ) + jiffies;
+			warning_timeout = (PQI_QUIESCE_WARNING_TIMEOUT_SECS * HZ) + jiffies;
 		}
 		usleep_range(1000, 2000);
 	}
@@ -430,7 +485,7 @@
 	pqi_schedule_rescan_worker_with_delay(ctrl_info, 0);
 }
 
-#define PQI_RESCAN_WORK_DELAY	(10 * PQI_HZ)
+#define PQI_RESCAN_WORK_DELAY	(10 * HZ)
 
 static inline void pqi_schedule_rescan_worker_delayed(struct pqi_ctrl_info *ctrl_info)
 {
@@ -523,6 +578,10 @@
 	cdb = request->cdb;
 
 	switch (cmd) {
+	case TEST_UNIT_READY:
+		request->data_direction = SOP_READ_FLAG;
+		cdb[0] = TEST_UNIT_READY;
+		break;
 	case INQUIRY:
 		request->data_direction = SOP_READ_FLAG;
 		cdb[0] = INQUIRY;
@@ -536,10 +595,14 @@
 	case CISS_REPORT_PHYS:
 		request->data_direction = SOP_READ_FLAG;
 		cdb[0] = cmd;
-		if (cmd == CISS_REPORT_PHYS)
-			cdb[1] = CISS_REPORT_PHYS_FLAG_OTHER;
-		else
+		if (cmd == CISS_REPORT_PHYS) {
+			if (ctrl_info->rpl_extended_format_4_5_supported)
+				cdb[1] = CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_4;
+			else
+				cdb[1] = CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_2;
+		} else {
 			cdb[1] = ctrl_info->ciss_report_log_flags;
+		}
 		put_unaligned_be32(cdb_length, &cdb[6]);
 		break;
 	case CISS_GET_RAID_MAP:
@@ -615,23 +678,36 @@
 	io_request->raid_bypass = false;
 }
 
-static struct pqi_io_request *pqi_alloc_io_request(
-	struct pqi_ctrl_info *ctrl_info)
+static inline struct pqi_io_request *pqi_alloc_io_request(struct pqi_ctrl_info *ctrl_info, struct scsi_cmnd *scmd)
 {
 	struct pqi_io_request *io_request;
-	u16 i = ctrl_info->next_io_request_slot;	/* benignly racy */
+	u16 i;
 
-	while (1) {
+	if (scmd) { /* SML I/O request */
+		u32 blk_tag = blk_mq_unique_tag(scsi_cmd_to_rq(scmd));
+
+		i = blk_mq_unique_tag_to_tag(blk_tag);
 		io_request = &ctrl_info->io_request_pool[i];
-		if (atomic_inc_return(&io_request->refcount) == 1)
-			break;
-		atomic_dec(&io_request->refcount);
-		i = (i + 1) % ctrl_info->max_io_slots;
+		if (atomic_inc_return(&io_request->refcount) > 1) {
+			atomic_dec(&io_request->refcount);
+			return NULL;
+		}
+	} else { /* IOCTL or driver internal request */
+		/*
+		 * benignly racy - may have to wait for an open slot.
+		 * command slot range is scsi_ml_can_queue -
+		 *         [scsi_ml_can_queue + (PQI_RESERVED_IO_SLOTS - 1)]
+		 */
+		i = 0;
+		while (1) {
+			io_request = &ctrl_info->io_request_pool[ctrl_info->scsi_ml_can_queue + i];
+			if (atomic_inc_return(&io_request->refcount) == 1)
+				break;
+			atomic_dec(&io_request->refcount);
+			i = (i + 1) % PQI_RESERVED_IO_SLOTS;
+		}
 	}
 
-	/* benignly racy */
-	ctrl_info->next_io_request_slot = (i + 1) % ctrl_info->max_io_slots;
-
 	pqi_reinit_io_request(io_request);
 
 	return io_request;
@@ -998,7 +1074,7 @@
 	return rc;
 }
 
-#define PQI_UPDATE_TIME_WORK_INTERVAL	(24UL * 60 * 60 * PQI_HZ)
+#define PQI_UPDATE_TIME_WORK_INTERVAL	(24UL * 60 * 60 * HZ)
 
 static void pqi_update_time_worker(struct work_struct *work)
 {
@@ -1096,7 +1172,64 @@
 
 static inline int pqi_report_phys_luns(struct pqi_ctrl_info *ctrl_info, void **buffer)
 {
-	return pqi_report_phys_logical_luns(ctrl_info, CISS_REPORT_PHYS, buffer);
+	int rc;
+	unsigned int i;
+	u8 rpl_response_format;
+	u32 num_physicals;
+	size_t rpl_16byte_wwid_list_length;
+	void *rpl_list;
+	struct report_lun_header *rpl_header;
+	struct report_phys_lun_8byte_wwid_list *rpl_8byte_wwid_list;
+	struct report_phys_lun_16byte_wwid_list *rpl_16byte_wwid_list;
+
+	rc = pqi_report_phys_logical_luns(ctrl_info, CISS_REPORT_PHYS, &rpl_list);
+	if (rc)
+		return rc;
+
+	if (ctrl_info->rpl_extended_format_4_5_supported) {
+		rpl_header = rpl_list;
+		rpl_response_format = rpl_header->flags & CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_MASK;
+		if (rpl_response_format == CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_4) {
+			*buffer = rpl_list;
+			return 0;
+		} else if (rpl_response_format != CISS_REPORT_PHYS_FLAG_EXTENDED_FORMAT_2) {
+			dev_err(&ctrl_info->pci_dev->dev,
+				"RPL returned unsupported data format %u\n",
+				rpl_response_format);
+			return -EINVAL;
+		} else {
+			dev_warn(&ctrl_info->pci_dev->dev,
+				"RPL returned extended format 2 instead of 4\n");
+		}
+	}
+
+	rpl_8byte_wwid_list = rpl_list;
+	num_physicals = get_unaligned_be32(&rpl_8byte_wwid_list->header.list_length) / sizeof(rpl_8byte_wwid_list->lun_entries[0]);
+	rpl_16byte_wwid_list_length = sizeof(struct report_lun_header) + (num_physicals * sizeof(struct report_phys_lun_16byte_wwid));
+
+	rpl_16byte_wwid_list = kmalloc(rpl_16byte_wwid_list_length, GFP_KERNEL);
+	if (!rpl_16byte_wwid_list)
+		return -ENOMEM;
+
+	put_unaligned_be32(num_physicals * sizeof(struct report_phys_lun_16byte_wwid),
+		&rpl_16byte_wwid_list->header.list_length);
+	rpl_16byte_wwid_list->header.flags = rpl_8byte_wwid_list->header.flags;
+
+	for (i = 0; i < num_physicals; i++) {
+		memcpy(&rpl_16byte_wwid_list->lun_entries[i].lunid, &rpl_8byte_wwid_list->lun_entries[i].lunid, sizeof(rpl_8byte_wwid_list->lun_entries[i].lunid));
+		memcpy(&rpl_16byte_wwid_list->lun_entries[i].wwid[0], &rpl_8byte_wwid_list->lun_entries[i].wwid, sizeof(rpl_8byte_wwid_list->lun_entries[i].wwid));
+		memset(&rpl_16byte_wwid_list->lun_entries[i].wwid[8], 0, 8);
+		rpl_16byte_wwid_list->lun_entries[i].device_type = rpl_8byte_wwid_list->lun_entries[i].device_type;
+		rpl_16byte_wwid_list->lun_entries[i].device_flags = rpl_8byte_wwid_list->lun_entries[i].device_flags;
+		rpl_16byte_wwid_list->lun_entries[i].lun_count = rpl_8byte_wwid_list->lun_entries[i].lun_count;
+		rpl_16byte_wwid_list->lun_entries[i].redundant_paths = rpl_8byte_wwid_list->lun_entries[i].redundant_paths;
+		rpl_16byte_wwid_list->lun_entries[i].aio_handle = rpl_8byte_wwid_list->lun_entries[i].aio_handle;
+	}
+
+	kfree(rpl_8byte_wwid_list);
+	*buffer = rpl_16byte_wwid_list;
+
+	return 0;
 }
 
 static inline int pqi_report_logical_luns(struct pqi_ctrl_info *ctrl_info, void **buffer)
@@ -1105,14 +1238,14 @@
 }
 
 static int pqi_get_device_lists(struct pqi_ctrl_info *ctrl_info,
-	struct report_phys_lun_extended **physdev_list,
-	struct report_log_lun_extended **logdev_list)
+	struct report_phys_lun_16byte_wwid_list **physdev_list,
+	struct report_log_lun_list **logdev_list)
 {
 	int rc;
 	size_t logdev_list_length;
 	size_t logdev_data_length;
-	struct report_log_lun_extended *internal_logdev_list;
-	struct report_log_lun_extended *logdev_data;
+	struct report_log_lun_list *internal_logdev_list;
+	struct report_log_lun_list *logdev_data;
 	struct report_lun_header report_lun_header;
 
 	rc = pqi_report_phys_luns(ctrl_info, (void **)physdev_list);
@@ -1137,7 +1270,7 @@
 	} else {
 		memset(&report_lun_header, 0, sizeof(report_lun_header));
 		logdev_data =
-			(struct report_log_lun_extended *)&report_lun_header;
+			(struct report_log_lun_list *)&report_lun_header;
 		logdev_list_length = 0;
 	}
 
@@ -1145,7 +1278,7 @@
 		logdev_list_length;
 
 	internal_logdev_list = kmalloc(logdev_data_length +
-		sizeof(struct report_log_lun_extended), GFP_KERNEL);
+		sizeof(struct report_log_lun), GFP_KERNEL);
 	if (!internal_logdev_list) {
 		kfree(*logdev_list);
 		*logdev_list = NULL;
@@ -1154,9 +1287,9 @@
 
 	memcpy(internal_logdev_list, logdev_data, logdev_data_length);
 	memset((u8 *)internal_logdev_list + logdev_data_length, 0,
-		sizeof(struct report_log_lun_extended_entry));
+		sizeof(struct report_log_lun));
 	put_unaligned_be32(logdev_list_length +
-		sizeof(struct report_log_lun_extended_entry),
+		sizeof(struct report_log_lun),
 		&internal_logdev_list->header.list_length);
 
 	kfree(*logdev_list);
@@ -1452,6 +1585,7 @@
 	device->volume_offline = volume_offline;
 }
 
+#define PQI_DEVICE_NCQ_PRIO_SUPPORTED	0x01
 #define PQI_DEVICE_PHY_MAP_SUPPORTED	0x10
 
 static int pqi_get_physical_device_info(struct pqi_ctrl_info *ctrl_info,
@@ -1489,10 +1623,7 @@
 		&id_phys->alternate_paths_phys_connector,
 		sizeof(device->phys_connector));
 	device->bay = id_phys->phys_bay_in_box;
-
-	memcpy(&device->page_83_identifier, &id_phys->page_83_identifier,
-		sizeof(device->page_83_identifier));
-
+	device->lun_count = id_phys->multi_lun_device_lun_count;
 	if ((id_phys->even_more_flags & PQI_DEVICE_PHY_MAP_SUPPORTED) &&
 		id_phys->phy_count)
 		device->phy_id =
@@ -1500,6 +1631,10 @@
 	else
 		device->phy_id = 0xFF;
 
+	device->ncq_prio_support =
+		((get_unaligned_le32(&id_phys->misc_drive_flags) >> 16) &
+		PQI_DEVICE_NCQ_PRIO_SUPPORTED);
+
 	return 0;
 }
 
@@ -1543,7 +1678,86 @@
 	return rc;
 }
 
-static int pqi_get_device_info(struct pqi_ctrl_info *ctrl_info,
+/*
+ * Prevent adding drive to OS for some corner cases such as a drive
+ * undergoing a sanitize operation. Some OSes will continue to poll
+ * the drive until the sanitize completes, which can take hours,
+ * resulting in long bootup delays. Commands such as TUR, READ_CAP
+ * are allowed, but READ/WRITE cause check condition. So the OS
+ * cannot check/read the partition table.
+ * Note: devices that have completed sanitize must be re-enabled
+ *       using the management utility.
+ */
+static bool pqi_keep_device_offline(struct pqi_ctrl_info *ctrl_info,
+	struct pqi_scsi_dev *device)
+{
+	u8 scsi_status;
+	int rc;
+	enum dma_data_direction dir;
+	char *buffer;
+	int buffer_length = 64;
+	size_t sense_data_length;
+	struct scsi_sense_hdr sshdr;
+	struct pqi_raid_path_request request;
+	struct pqi_raid_error_info error_info;
+	bool offline = false; /* Assume keep online */
+
+	/* Do not check controllers. */
+	if (pqi_is_hba_lunid(device->scsi3addr))
+		return false;
+
+	/* Do not check LVs. */
+	if (pqi_is_logical_device(device))
+		return false;
+
+	buffer = kmalloc(buffer_length, GFP_KERNEL);
+	if (!buffer)
+		return false; /* Assume not offline */
+
+	/* Check for SANITIZE in progress using TUR */
+	rc = pqi_build_raid_path_request(ctrl_info, &request,
+		TEST_UNIT_READY, RAID_CTLR_LUNID, buffer,
+		buffer_length, 0, &dir);
+	if (rc)
+		goto out; /* Assume not offline */
+
+	memcpy(request.lun_number, device->scsi3addr, sizeof(request.lun_number));
+
+	rc = pqi_submit_raid_request_synchronous(ctrl_info, &request.header, 0, &error_info);
+
+	if (rc)
+		goto out; /* Assume not offline */
+
+	scsi_status = error_info.status;
+	sense_data_length = get_unaligned_le16(&error_info.sense_data_length);
+	if (sense_data_length == 0)
+		sense_data_length =
+			get_unaligned_le16(&error_info.response_data_length);
+	if (sense_data_length) {
+		if (sense_data_length > sizeof(error_info.data))
+			sense_data_length = sizeof(error_info.data);
+
+		/*
+		 * Check for sanitize in progress: asc:0x04, ascq: 0x1b
+		 */
+		if (scsi_status == SAM_STAT_CHECK_CONDITION &&
+			scsi_normalize_sense(error_info.data,
+				sense_data_length, &sshdr) &&
+				sshdr.sense_key == NOT_READY &&
+				sshdr.asc == 0x04 &&
+				sshdr.ascq == 0x1b) {
+			device->device_offline = true;
+			offline = true;
+			goto out; /* Keep device offline */
+		}
+	}
+
+out:
+	kfree(buffer);
+	return offline;
+}
+
+static int pqi_get_device_info_phys_logical(struct pqi_ctrl_info *ctrl_info,
 	struct pqi_scsi_dev *device,
 	struct bmic_identify_physical_device *id_phys)
 {
@@ -1560,6 +1774,20 @@
 	return rc;
 }
 
+static int pqi_get_device_info(struct pqi_ctrl_info *ctrl_info,
+	struct pqi_scsi_dev *device,
+	struct bmic_identify_physical_device *id_phys)
+{
+	int rc;
+
+	rc = pqi_get_device_info_phys_logical(ctrl_info, device, id_phys);
+
+	if (rc == 0 && device->lun_count == 0)
+		device->lun_count = 1;
+
+	return rc;
+}
+
 static void pqi_show_volume_status(struct pqi_ctrl_info *ctrl_info,
 	struct pqi_scsi_dev *device)
 {
@@ -1692,22 +1920,25 @@
 static inline void pqi_remove_device(struct pqi_ctrl_info *ctrl_info, struct pqi_scsi_dev *device)
 {
 	int rc;
+	int lun;
 
-	pqi_device_remove_start(device);
-
-	rc = pqi_device_wait_for_pending_io(ctrl_info, device,
-		PQI_REMOVE_DEVICE_PENDING_IO_TIMEOUT_MSECS);
-	if (rc)
-		dev_err(&ctrl_info->pci_dev->dev,
-			"scsi %d:%d:%d:%d removing device with %d outstanding command(s)\n",
-			ctrl_info->scsi_host->host_no, device->bus,
-			device->target, device->lun,
-			atomic_read(&device->scsi_cmds_outstanding));
+	for (lun = 0; lun < device->lun_count; lun++) {
+		rc = pqi_device_wait_for_pending_io(ctrl_info, device, lun,
+			PQI_REMOVE_DEVICE_PENDING_IO_TIMEOUT_MSECS);
+		if (rc)
+			dev_err(&ctrl_info->pci_dev->dev,
+				"scsi %d:%d:%d:%d removing device with %d outstanding command(s)\n",
+				ctrl_info->scsi_host->host_no, device->bus,
+				device->target, lun,
+				atomic_read(&device->scsi_cmds_outstanding[lun]));
+	}
 
 	if (pqi_is_logical_device(device))
 		scsi_remove_device(device->sdev);
 	else
 		pqi_remove_sas_device(device);
+
+	pqi_device_remove_start(device);
 }
 
 /* Assumes the SCSI device list lock is held. */
@@ -1730,7 +1961,7 @@
 		return false;
 
 	if (dev1->is_physical_device)
-		return dev1->wwid == dev2->wwid;
+		return memcmp(dev1->wwid, dev2->wwid, sizeof(dev1->wwid)) == 0;
 
 	return memcmp(dev1->volume_id, dev2->volume_id, sizeof(dev1->volume_id)) == 0;
 }
@@ -1800,7 +2031,9 @@
 	else
 		count += scnprintf(buffer + count,
 			PQI_DEV_INFO_BUFFER_LENGTH - count,
-			" %016llx", device->sas_address);
+			" %016llx%016llx",
+			get_unaligned_be64(&device->wwid[0]),
+			get_unaligned_be64(&device->wwid[8]));
 
 	count += scnprintf(buffer + count, PQI_DEV_INFO_BUFFER_LENGTH - count,
 		" %s %.8s %.16s ",
@@ -1830,10 +2063,27 @@
 	dev_info(&ctrl_info->pci_dev->dev, "%s %s\n", action, buffer);
 }
 
+static bool pqi_raid_maps_equal(struct raid_map *raid_map1, struct raid_map *raid_map2)
+{
+	u32 raid_map1_size;
+	u32 raid_map2_size;
+
+	if (raid_map1 == NULL || raid_map2 == NULL)
+		return raid_map1 == raid_map2;
+
+	raid_map1_size = get_unaligned_le32(&raid_map1->structure_size);
+	raid_map2_size = get_unaligned_le32(&raid_map2->structure_size);
+
+	if (raid_map1_size != raid_map2_size)
+		return false;
+
+	return memcmp(raid_map1, raid_map2, raid_map1_size) == 0;
+}
+
 /* Assumes the SCSI device list lock is held. */
 
-static void pqi_scsi_update_device(struct pqi_scsi_dev *existing_device,
-	struct pqi_scsi_dev *new_device)
+static void pqi_scsi_update_device(struct pqi_ctrl_info *ctrl_info,
+	struct pqi_scsi_dev *existing_device, struct pqi_scsi_dev *new_device)
 {
 	existing_device->device_type = new_device->device_type;
 	existing_device->bus = new_device->bus;
@@ -1843,50 +2093,48 @@
 		existing_device->target_lun_valid = true;
 	}
 
-	if ((existing_device->volume_status == CISS_LV_QUEUED_FOR_EXPANSION ||
-		existing_device->volume_status == CISS_LV_UNDERGOING_EXPANSION) &&
-		new_device->volume_status == CISS_LV_OK)
-		existing_device->rescan = true;
-
 	/* By definition, the scsi3addr and wwid fields are already the same. */
 
 	existing_device->is_physical_device = new_device->is_physical_device;
-	existing_device->is_external_raid_device =
-		new_device->is_external_raid_device;
-	existing_device->is_expander_smp_device =
-		new_device->is_expander_smp_device;
-	existing_device->aio_enabled = new_device->aio_enabled;
-	memcpy(existing_device->vendor, new_device->vendor,
-		sizeof(existing_device->vendor));
-	memcpy(existing_device->model, new_device->model,
-		sizeof(existing_device->model));
+	memcpy(existing_device->vendor, new_device->vendor, sizeof(existing_device->vendor));
+	memcpy(existing_device->model, new_device->model, sizeof(existing_device->model));
 	existing_device->sas_address = new_device->sas_address;
-	existing_device->raid_level = new_device->raid_level;
 	existing_device->queue_depth = new_device->queue_depth;
-	existing_device->aio_handle = new_device->aio_handle;
-	existing_device->volume_status = new_device->volume_status;
-	existing_device->active_path_index = new_device->active_path_index;
-	existing_device->phy_id = new_device->phy_id;
-	existing_device->path_map = new_device->path_map;
-	existing_device->bay = new_device->bay;
-	existing_device->box_index = new_device->box_index;
-	existing_device->phys_box_on_bus = new_device->phys_box_on_bus;
-	existing_device->phy_connected_dev_type = new_device->phy_connected_dev_type;
-	memcpy(existing_device->box, new_device->box,
-		sizeof(existing_device->box));
-	memcpy(existing_device->phys_connector, new_device->phys_connector,
-		sizeof(existing_device->phys_connector));
-	existing_device->next_bypass_group = 0;
-	kfree(existing_device->raid_map);
-	existing_device->raid_map = new_device->raid_map;
-	existing_device->raid_bypass_configured =
-		new_device->raid_bypass_configured;
-	existing_device->raid_bypass_enabled =
-		new_device->raid_bypass_enabled;
 	existing_device->device_offline = false;
+	existing_device->lun_count = new_device->lun_count;
 
-	/* To prevent this from being freed later. */
-	new_device->raid_map = NULL;
+	if (pqi_is_logical_device(existing_device)) {
+		existing_device->is_external_raid_device = new_device->is_external_raid_device;
+
+		if (existing_device->devtype == TYPE_DISK) {
+			existing_device->raid_level = new_device->raid_level;
+			existing_device->volume_status = new_device->volume_status;
+			if (ctrl_info->logical_volume_rescan_needed)
+				existing_device->rescan = true;
+			memset(existing_device->next_bypass_group, 0, sizeof(existing_device->next_bypass_group));
+			if (!pqi_raid_maps_equal(existing_device->raid_map, new_device->raid_map)) {
+				kfree(existing_device->raid_map);
+				existing_device->raid_map = new_device->raid_map;
+				/* To prevent this from being freed later. */
+				new_device->raid_map = NULL;
+			}
+			existing_device->raid_bypass_configured = new_device->raid_bypass_configured;
+			existing_device->raid_bypass_enabled = new_device->raid_bypass_enabled;
+		}
+	} else {
+		existing_device->aio_enabled = new_device->aio_enabled;
+		existing_device->aio_handle = new_device->aio_handle;
+		existing_device->is_expander_smp_device = new_device->is_expander_smp_device;
+		existing_device->active_path_index = new_device->active_path_index;
+		existing_device->phy_id = new_device->phy_id;
+		existing_device->path_map = new_device->path_map;
+		existing_device->bay = new_device->bay;
+		existing_device->box_index = new_device->box_index;
+		existing_device->phys_box_on_bus = new_device->phys_box_on_bus;
+		existing_device->phy_connected_dev_type = new_device->phy_connected_dev_type;
+		memcpy(existing_device->box, new_device->box, sizeof(existing_device->box));
+		memcpy(existing_device->phys_connector, new_device->phys_connector, sizeof(existing_device->phys_connector));
+	}
 }
 
 static inline void pqi_free_device(struct pqi_scsi_dev *device)
@@ -1963,7 +2211,7 @@
 			 */
 			device->new_device = false;
 			matching_device->device_gone = false;
-			pqi_scsi_update_device(matching_device, device);
+			pqi_scsi_update_device(ctrl_info, matching_device, device);
 			break;
 		case DEVICE_NOT_FOUND:
 			/*
@@ -1986,7 +2234,7 @@
 	list_for_each_entry_safe(device, next, &ctrl_info->scsi_device_list,
 		scsi_device_list_entry) {
 		if (device->device_gone) {
-			list_del_init(&device->scsi_device_list_entry);
+			list_del(&device->scsi_device_list_entry);
 			list_add_tail(&device->delete_list_entry, &delete_list);
 		}
 	}
@@ -2025,20 +2273,18 @@
 		if (device->volume_offline) {
 			pqi_dev_info(ctrl_info, "offline", device);
 			pqi_show_volume_status(ctrl_info, device);
-		}
-		list_del(&device->delete_list_entry);
-		if (pqi_is_device_added(device)) {
-			pqi_remove_device(ctrl_info, device);
 		} else {
-			if (!device->volume_offline)
-				pqi_dev_info(ctrl_info, "removed", device);
-			pqi_free_device(device);
+			pqi_dev_info(ctrl_info, "removed", device);
 		}
+		if (pqi_is_device_added(device))
+			pqi_remove_device(ctrl_info, device);
+		list_del(&device->delete_list_entry);
+		pqi_free_device(device);
 	}
 
 	/*
-	 * Notify the SCSI ML if the queue depth of any existing device has
-	 * changed.
+	 * Notify the SML of any existing device changes such as;
+	 * queue depth, device size.
 	 */
 	list_for_each_entry(device, &ctrl_info->scsi_device_list, scsi_device_list_entry) {
 		if (device->sdev && device->queue_depth != device->advertised_queue_depth) {
@@ -2067,6 +2313,9 @@
 			}
 		}
 	}
+
+	ctrl_info->logical_volume_rescan_needed = false;
+
 }
 
 static inline bool pqi_is_supported_device(struct pqi_scsi_dev *device)
@@ -2098,16 +2347,12 @@
 	scsi3addr[3] |= 0xc0;
 }
 
-static inline bool pqi_is_device_with_sas_address(struct pqi_scsi_dev *device)
+static inline bool pqi_is_multipath_device(struct pqi_scsi_dev *device)
 {
-	switch (device->device_type) {
-	case SA_DEVICE_TYPE_SAS:
-	case SA_DEVICE_TYPE_EXPANDER_SMP:
-	case SA_DEVICE_TYPE_SES:
-		return true;
-	}
+	if (pqi_is_logical_device(device))
+		return false;
 
-	return false;
+	return (device->path_map & (device->path_map - 1)) != 0;
 }
 
 static inline bool pqi_expose_device(struct pqi_scsi_dev *device)
@@ -2115,25 +2360,15 @@
 	return !device->is_physical_device || !pqi_skip_device(device->scsi3addr);
 }
 
-static inline void pqi_set_physical_device_wwid(struct pqi_ctrl_info *ctrl_info,
-	struct pqi_scsi_dev *device, struct report_phys_lun_extended_entry *phys_lun_ext_entry)
-{
-	if (ctrl_info->unique_wwid_in_report_phys_lun_supported ||
-		pqi_is_device_with_sas_address(device))
-		device->wwid = phys_lun_ext_entry->wwid;
-	else
-		device->wwid = cpu_to_be64(get_unaligned_be64(&device->page_83_identifier));
-}
-
 static int pqi_update_scsi_devices(struct pqi_ctrl_info *ctrl_info)
 {
 	int i;
 	int rc;
 	LIST_HEAD(new_device_list_head);
-	struct report_phys_lun_extended *physdev_list = NULL;
-	struct report_log_lun_extended *logdev_list = NULL;
-	struct report_phys_lun_extended_entry *phys_lun_ext_entry;
-	struct report_log_lun_extended_entry *log_lun_ext_entry;
+	struct report_phys_lun_16byte_wwid_list *physdev_list = NULL;
+	struct report_log_lun_list *logdev_list = NULL;
+	struct report_phys_lun_16byte_wwid *phys_lun;
+	struct report_log_lun *log_lun;
 	struct bmic_identify_physical_device *id_phys = NULL;
 	u32 num_physicals;
 	u32 num_logicals;
@@ -2184,10 +2419,9 @@
 
 		if (pqi_hide_vsep) {
 			for (i = num_physicals - 1; i >= 0; i--) {
-				phys_lun_ext_entry =
-						&physdev_list->lun_entries[i];
-				if (CISS_GET_DRIVE_NUMBER(phys_lun_ext_entry->lunid) == PQI_VSEP_CISS_BTL) {
-					pqi_mask_device(phys_lun_ext_entry->lunid);
+				phys_lun = &physdev_list->lun_entries[i];
+				if (CISS_GET_DRIVE_NUMBER(phys_lun->lunid) == PQI_VSEP_CISS_BTL) {
+					pqi_mask_device(phys_lun->lunid);
 					break;
 				}
 			}
@@ -2231,16 +2465,14 @@
 		if ((!pqi_expose_ld_first && i < num_physicals) ||
 			(pqi_expose_ld_first && i >= num_logicals)) {
 			is_physical_device = true;
-			phys_lun_ext_entry =
-				&physdev_list->lun_entries[physical_index++];
-			log_lun_ext_entry = NULL;
-			scsi3addr = phys_lun_ext_entry->lunid;
+			phys_lun = &physdev_list->lun_entries[physical_index++];
+			log_lun = NULL;
+			scsi3addr = phys_lun->lunid;
 		} else {
 			is_physical_device = false;
-			phys_lun_ext_entry = NULL;
-			log_lun_ext_entry =
-				&logdev_list->lun_entries[logical_index++];
-			scsi3addr = log_lun_ext_entry->lunid;
+			phys_lun = NULL;
+			log_lun = &logdev_list->lun_entries[logical_index++];
+			scsi3addr = log_lun->lunid;
 		}
 
 		if (is_physical_device && pqi_skip_device(scsi3addr))
@@ -2255,7 +2487,7 @@
 		memcpy(device->scsi3addr, scsi3addr, sizeof(device->scsi3addr));
 		device->is_physical_device = is_physical_device;
 		if (is_physical_device) {
-			device->device_type = phys_lun_ext_entry->device_type;
+			device->device_type = phys_lun->device_type;
 			if (device->device_type == SA_DEVICE_TYPE_EXPANDER_SMP)
 				device->is_expander_smp_device = true;
 		} else {
@@ -2266,6 +2498,10 @@
 		if (!pqi_is_supported_device(device))
 			continue;
 
+		/* Do not present disks that the OS cannot fully probe */
+		if (pqi_keep_device_offline(ctrl_info, device))
+			continue;
+
 		/* Gather information about the device. */
 		rc = pqi_get_device_info(ctrl_info, device, id_phys);
 		if (rc == -ENOMEM) {
@@ -2276,8 +2512,9 @@
 		if (rc) {
 			if (device->is_physical_device)
 				dev_warn(&ctrl_info->pci_dev->dev,
-					"obtaining device info failed, skipping physical device %016llx\n",
-					get_unaligned_be64(&phys_lun_ext_entry->wwid));
+					"obtaining device info failed, skipping physical device %016llx%016llx\n",
+					get_unaligned_be64(&phys_lun->wwid[0]),
+					get_unaligned_be64(&phys_lun->wwid[8]));
 			else
 				dev_warn(&ctrl_info->pci_dev->dev,
 					"obtaining device info failed, skipping logical device %08x%08x\n",
@@ -2290,21 +2527,20 @@
 		pqi_assign_bus_target_lun(device);
 
 		if (device->is_physical_device) {
-			pqi_set_physical_device_wwid(ctrl_info, device, phys_lun_ext_entry);
-			if ((phys_lun_ext_entry->device_flags &
+			memcpy(device->wwid, phys_lun->wwid, sizeof(device->wwid));
+			if ((phys_lun->device_flags &
 				CISS_REPORT_PHYS_DEV_FLAG_AIO_ENABLED) &&
-				phys_lun_ext_entry->aio_handle) {
+				phys_lun->aio_handle) {
 					device->aio_enabled = true;
 					device->aio_handle =
-						phys_lun_ext_entry->aio_handle;
+						phys_lun->aio_handle;
 			}
 		} else {
-			memcpy(device->volume_id, log_lun_ext_entry->volume_id,
+			memcpy(device->volume_id, log_lun->volume_id,
 				sizeof(device->volume_id));
 		}
 
-		if (pqi_is_device_with_sas_address(device))
-			device->sas_address = get_unaligned_be64(&device->wwid);
+		device->sas_address = get_unaligned_be64(&device->wwid[0]);
 
 		new_device_list[num_valid_devices++] = device;
 	}
@@ -2752,11 +2988,11 @@
 		if (rmd.is_write) {
 			pqi_calc_aio_r1_nexus(raid_map, &rmd);
 		} else {
-			group = device->next_bypass_group;
+			group = device->next_bypass_group[rmd.map_index];
 			next_bypass_group = group + 1;
 			if (next_bypass_group >= rmd.layout_map_count)
 				next_bypass_group = 0;
-			device->next_bypass_group = next_bypass_group;
+			device->next_bypass_group[rmd.map_index] = next_bypass_group;
 			rmd.map_index += group * rmd.data_disks_per_row;
 		}
 	} else if ((device->raid_level == SA_RAID_5 ||
@@ -2811,7 +3047,7 @@
 
 	return pqi_aio_submit_io(ctrl_info, scmd, rmd.aio_handle,
 		rmd.cdb, rmd.cdb_length, queue_group,
-		encryption_info_ptr, true);
+		encryption_info_ptr, true, false);
 }
 
 #define PQI_STATUS_IDLE		0x0
@@ -2836,7 +3072,7 @@
 	u8 status;
 
 	pqi_registers = ctrl_info->pqi_registers;
-	timeout = (PQI_MODE_READY_TIMEOUT_SECS * PQI_HZ) + jiffies;
+	timeout = (PQI_MODE_READY_TIMEOUT_SECS * HZ) + jiffies;
 
 	while (1) {
 		signature = readq(&pqi_registers->signature);
@@ -3015,12 +3251,14 @@
 	int residual_count;
 	int xfer_count;
 	bool device_offline;
+	struct pqi_scsi_dev *device;
 
 	scmd = io_request->scmd;
 	error_info = io_request->error_info;
 	host_byte = DID_OK;
 	sense_data_length = 0;
 	device_offline = false;
+	device = scmd->device->hostdata;
 
 	switch (error_info->service_response) {
 	case PQI_AIO_SERV_RESPONSE_COMPLETE:
@@ -3045,8 +3283,14 @@
 			break;
 		case PQI_AIO_STATUS_AIO_PATH_DISABLED:
 			pqi_aio_path_disabled(io_request);
-			scsi_status = SAM_STAT_GOOD;
-			io_request->status = -EAGAIN;
+			if (pqi_is_multipath_device(device)) {
+				pqi_device_remove_start(device);
+				host_byte = DID_NO_CONNECT;
+				scsi_status = SAM_STAT_CHECK_CONDITION;
+			} else {
+				scsi_status = SAM_STAT_GOOD;
+				io_request->status = -EAGAIN;
+			}
 			break;
 		case PQI_AIO_STATUS_NO_PATH_TO_DEVICE:
 		case PQI_AIO_STATUS_INVALID_DEVICE:
@@ -3120,6 +3364,9 @@
 	case SOP_TMF_REJECTED:
 		rc = -EAGAIN;
 		break;
+	case SOP_RC_INCORRECT_LOGICAL_UNIT:
+		rc = -ENODEV;
+		break;
 	default:
 		rc = -EIO;
 		break;
@@ -3132,9 +3379,10 @@
 	return rc;
 }
 
-static inline void pqi_invalid_response(struct pqi_ctrl_info *ctrl_info)
+static inline void pqi_invalid_response(struct pqi_ctrl_info *ctrl_info,
+	enum pqi_ctrl_shutdown_reason ctrl_shutdown_reason)
 {
-	pqi_take_ctrl_offline(ctrl_info);
+	pqi_take_ctrl_offline(ctrl_info, ctrl_shutdown_reason);
 }
 
 static int pqi_process_io_intr(struct pqi_ctrl_info *ctrl_info, struct pqi_queue_group *queue_group)
@@ -3152,7 +3400,7 @@
 	while (1) {
 		oq_pi = readl(queue_group->oq_pi);
 		if (oq_pi >= ctrl_info->num_elements_per_oq) {
-			pqi_invalid_response(ctrl_info);
+			pqi_invalid_response(ctrl_info, PQI_IO_PI_OUT_OF_RANGE);
 			dev_err(&ctrl_info->pci_dev->dev,
 				"I/O interrupt: producer index (%u) out of range (0-%u): consumer index: %u\n",
 				oq_pi, ctrl_info->num_elements_per_oq - 1, oq_ci);
@@ -3167,7 +3415,7 @@
 
 		request_id = get_unaligned_le16(&response->request_id);
 		if (request_id >= ctrl_info->max_io_slots) {
-			pqi_invalid_response(ctrl_info);
+			pqi_invalid_response(ctrl_info, PQI_INVALID_REQ_ID);
 			dev_err(&ctrl_info->pci_dev->dev,
 				"request ID in response (%u) out of range (0-%u): producer index: %u  consumer index: %u\n",
 				request_id, ctrl_info->max_io_slots - 1, oq_pi, oq_ci);
@@ -3176,7 +3424,7 @@
 
 		io_request = &ctrl_info->io_request_pool[request_id];
 		if (atomic_read(&io_request->refcount) == 0) {
-			pqi_invalid_response(ctrl_info);
+			pqi_invalid_response(ctrl_info, PQI_UNMATCHED_REQ_ID);
 			dev_err(&ctrl_info->pci_dev->dev,
 				"request ID in response (%u) does not match an outstanding I/O request: producer index: %u  consumer index: %u\n",
 				request_id, oq_pi, oq_ci);
@@ -3212,7 +3460,7 @@
 			pqi_process_io_error(response->header.iu_type, io_request);
 			break;
 		default:
-			pqi_invalid_response(ctrl_info);
+			pqi_invalid_response(ctrl_info, PQI_UNEXPECTED_IU_TYPE);
 			dev_err(&ctrl_info->pci_dev->dev,
 				"unexpected IU type: 0x%x: producer index: %u  consumer index: %u\n",
 				response->header.iu_type, oq_pi, oq_ci);
@@ -3321,7 +3569,7 @@
 	u8 status;
 	unsigned long timeout;
 
-	timeout = (PQI_SOFT_RESET_STATUS_TIMEOUT_SECS * PQI_HZ) + jiffies;
+	timeout = (PQI_SOFT_RESET_STATUS_TIMEOUT_SECS * HZ) + jiffies;
 
 	while (1) {
 		status = pqi_read_soft_reset_status(ctrl_info);
@@ -3394,7 +3642,7 @@
 		pqi_ofa_free_host_buffer(ctrl_info);
 		pqi_ctrl_ofa_done(ctrl_info);
 		pqi_ofa_ctrl_unquiesce(ctrl_info);
-		pqi_take_ctrl_offline(ctrl_info);
+		pqi_take_ctrl_offline(ctrl_info, PQI_OFA_RESPONSE_TIMEOUT);
 		break;
 	}
 }
@@ -3460,6 +3708,20 @@
 	return ack_event;
 }
 
+static void pqi_disable_raid_bypass(struct pqi_ctrl_info *ctrl_info)
+{
+	unsigned long flags;
+	struct pqi_scsi_dev *device;
+
+	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
+
+	list_for_each_entry(device, &ctrl_info->scsi_device_list, scsi_device_list_entry)
+		if (device->raid_bypass_enabled)
+			device->raid_bypass_enabled = false;
+
+	spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
+}
+
 static void pqi_event_worker(struct work_struct *work)
 {
 	unsigned int i;
@@ -3485,6 +3747,10 @@
 			} else {
 				ack_event = true;
 				rescan_needed = true;
+				if (event->event_type == PQI_EVENT_TYPE_LOGICAL_DEVICE)
+					ctrl_info->logical_volume_rescan_needed = true;
+				else if (event->event_type == PQI_EVENT_TYPE_AIO_STATE_CHANGE)
+					pqi_disable_raid_bypass(ctrl_info);
 			}
 			if (ack_event)
 				pqi_acknowledge_event(ctrl_info, event);
@@ -3492,14 +3758,17 @@
 		event++;
 	}
 
+#define PQI_RESCAN_WORK_FOR_EVENT_DELAY		(5 * HZ)
+
 	if (rescan_needed)
-		pqi_schedule_rescan_worker_delayed(ctrl_info);
+		pqi_schedule_rescan_worker_with_delay(ctrl_info,
+			PQI_RESCAN_WORK_FOR_EVENT_DELAY);
 
 out:
 	pqi_ctrl_unbusy(ctrl_info);
 }
 
-#define PQI_HEARTBEAT_TIMER_INTERVAL	(10 * PQI_HZ)
+#define PQI_HEARTBEAT_TIMER_INTERVAL	(10 * HZ)
 
 static void pqi_heartbeat_timer_handler(struct timer_list *t)
 {
@@ -3519,7 +3788,7 @@
 			dev_err(&ctrl_info->pci_dev->dev,
 				"no heartbeat detected - last heartbeat count: %u\n",
 				heartbeat_count);
-			pqi_take_ctrl_offline(ctrl_info);
+			pqi_take_ctrl_offline(ctrl_info, PQI_NO_HEARTBEAT);
 			return;
 		}
 	} else {
@@ -3583,7 +3852,7 @@
 	while (1) {
 		oq_pi = readl(event_queue->oq_pi);
 		if (oq_pi >= PQI_NUM_EVENT_QUEUE_ELEMENTS) {
-			pqi_invalid_response(ctrl_info);
+			pqi_invalid_response(ctrl_info, PQI_EVENT_PI_OUT_OF_RANGE);
 			dev_err(&ctrl_info->pci_dev->dev,
 				"event interrupt: producer index (%u) out of range (0-%u): consumer index: %u\n",
 				oq_pi, PQI_NUM_EVENT_QUEUE_ELEMENTS - 1, oq_ci);
@@ -3787,10 +4056,14 @@
 static int pqi_enable_msix_interrupts(struct pqi_ctrl_info *ctrl_info)
 {
 	int num_vectors_enabled;
+	unsigned int flags = PCI_IRQ_MSIX;
+
+	if (!pqi_disable_managed_interrupts)
+		flags |= PCI_IRQ_AFFINITY;
 
 	num_vectors_enabled = pci_alloc_irq_vectors(ctrl_info->pci_dev,
 			PQI_MIN_MSIX_VECTORS, ctrl_info->num_queue_groups,
-			PCI_IRQ_MSIX | PCI_IRQ_AFFINITY);
+			flags);
 	if (num_vectors_enabled < 0) {
 		dev_err(&ctrl_info->pci_dev->dev,
 			"MSI-X init failed with error %d\n",
@@ -4046,7 +4319,7 @@
 	return 0;
 }
 
-#define PQI_ADMIN_QUEUE_CREATE_TIMEOUT_JIFFIES		PQI_HZ
+#define PQI_ADMIN_QUEUE_CREATE_TIMEOUT_JIFFIES		HZ
 #define PQI_ADMIN_QUEUE_CREATE_POLL_INTERVAL_MSECS	1
 
 static int pqi_create_admin_queues(struct pqi_ctrl_info *ctrl_info)
@@ -4079,12 +4352,12 @@
 
 	timeout = PQI_ADMIN_QUEUE_CREATE_TIMEOUT_JIFFIES + jiffies;
 	while (1) {
+		msleep(PQI_ADMIN_QUEUE_CREATE_POLL_INTERVAL_MSECS);
 		status = readb(&pqi_registers->function_and_status_code);
 		if (status == PQI_STATUS_IDLE)
 			break;
 		if (time_after(jiffies, timeout))
 			return -ETIMEDOUT;
-		msleep(PQI_ADMIN_QUEUE_CREATE_POLL_INTERVAL_MSECS);
 	}
 
 	/*
@@ -4140,7 +4413,7 @@
 	admin_queues = &ctrl_info->admin_queues;
 	oq_ci = admin_queues->oq_ci_copy;
 
-	timeout = (PQI_ADMIN_REQUEST_TIMEOUT_SECS * PQI_HZ) + jiffies;
+	timeout = (PQI_ADMIN_REQUEST_TIMEOUT_SECS * HZ) + jiffies;
 
 	while (1) {
 		oq_pi = readl(admin_queues->oq_pi);
@@ -4255,7 +4528,7 @@
 
 	while (1) {
 		if (wait_for_completion_io_timeout(wait,
-			PQI_WAIT_FOR_COMPLETION_IO_TIMEOUT_SECS * PQI_HZ)) {
+			PQI_WAIT_FOR_COMPLETION_IO_TIMEOUT_SECS * HZ)) {
 			rc = 0;
 			break;
 		}
@@ -4335,7 +4608,7 @@
 		goto out;
 	}
 
-	io_request = pqi_alloc_io_request(ctrl_info);
+	io_request = pqi_alloc_io_request(ctrl_info, NULL);
 
 	put_unaligned_le16(io_request->index,
 		&(((struct pqi_raid_path_request *)request)->request_id));
@@ -4982,7 +5255,6 @@
 	}
 
 	ctrl_info->num_queue_groups = num_queue_groups;
-	ctrl_info->max_hw_queue_index = num_queue_groups - 1;
 
 	/*
 	 * Make sure that the max. inbound IU length is an even multiple
@@ -5252,6 +5524,7 @@
 	put_unaligned_le16(io_request->index, &request->request_id);
 	request->error_index = request->request_id;
 	memcpy(request->lun_number, device->scsi3addr, sizeof(request->lun_number));
+	request->ml_device_lun_number = (u8)scmd->device->lun;
 
 	cdb_length = min_t(size_t, scmd->cmd_len, sizeof(request->cdb));
 	memcpy(request->cdb, scmd->cmnd, cdb_length);
@@ -5279,10 +5552,10 @@
 	}
 
 	switch (scmd->sc_data_direction) {
-	case DMA_TO_DEVICE:
+	case DMA_FROM_DEVICE:
 		request->data_direction = SOP_READ_FLAG;
 		break;
-	case DMA_FROM_DEVICE:
+	case DMA_TO_DEVICE:
 		request->data_direction = SOP_WRITE_FLAG;
 		break;
 	case DMA_NONE:
@@ -5315,7 +5588,9 @@
 {
 	struct pqi_io_request *io_request;
 
-	io_request = pqi_alloc_io_request(ctrl_info);
+	io_request = pqi_alloc_io_request(ctrl_info, scmd);
+	if (!io_request)
+		return SCSI_MLQUEUE_HOST_BUSY;
 
 	return pqi_raid_submit_scsi_cmd_with_io_request(ctrl_info, io_request,
 		device, scmd, queue_group);
@@ -5356,44 +5631,88 @@
 	scsi_dma_unmap(scmd);
 	if (io_request->status == -EAGAIN || pqi_raid_bypass_retry_needed(io_request)) {
 		set_host_byte(scmd, DID_IMM_RETRY);
-		scmd->SCp.this_residual++;
+		pqi_cmd_priv(scmd)->this_residual++;
 	}
 
 	pqi_free_io_request(io_request);
 	pqi_scsi_done(scmd);
 }
 
+static inline bool pqi_is_io_high_priority(struct pqi_ctrl_info *ctrl_info,
+	struct pqi_scsi_dev *device, struct scsi_cmnd *scmd)
+{
+	bool io_high_prio;
+	int priority_class;
+
+	io_high_prio = false;
+
+	if (device->ncq_prio_enable) {
+		priority_class =
+			IOPRIO_PRIO_CLASS(req_get_ioprio(scsi_cmd_to_rq(scmd)));
+		if (priority_class == IOPRIO_CLASS_RT) {
+			/* Set NCQ priority for read/write commands. */
+			switch (scmd->cmnd[0]) {
+			case WRITE_16:
+			case READ_16:
+			case WRITE_12:
+			case READ_12:
+			case WRITE_10:
+			case READ_10:
+			case WRITE_6:
+			case READ_6:
+				io_high_prio = true;
+				break;
+			}
+		}
+	}
+
+	return io_high_prio;
+}
+
 static inline int pqi_aio_submit_scsi_cmd(struct pqi_ctrl_info *ctrl_info,
 	struct pqi_scsi_dev *device, struct scsi_cmnd *scmd,
 	struct pqi_queue_group *queue_group)
 {
+	bool io_high_prio;
+
+	io_high_prio = pqi_is_io_high_priority(ctrl_info, device, scmd);
+
 	return pqi_aio_submit_io(ctrl_info, scmd, device->aio_handle,
-		scmd->cmnd, scmd->cmd_len, queue_group, NULL, false);
+		scmd->cmnd, scmd->cmd_len, queue_group, NULL,
+		false, io_high_prio);
 }
 
 static int pqi_aio_submit_io(struct pqi_ctrl_info *ctrl_info,
 	struct scsi_cmnd *scmd, u32 aio_handle, u8 *cdb,
 	unsigned int cdb_length, struct pqi_queue_group *queue_group,
-	struct pqi_encryption_info *encryption_info, bool raid_bypass)
+	struct pqi_encryption_info *encryption_info, bool raid_bypass,
+	bool io_high_prio)
 {
 	int rc;
 	struct pqi_io_request *io_request;
 	struct pqi_aio_path_request *request;
+	struct pqi_scsi_dev *device;
 
-	io_request = pqi_alloc_io_request(ctrl_info);
+	device = scmd->device->hostdata;
+	io_request = pqi_alloc_io_request(ctrl_info, scmd);
+	if (!io_request)
+		return SCSI_MLQUEUE_HOST_BUSY;
 	io_request->io_complete_callback = pqi_aio_io_complete;
 	io_request->scmd = scmd;
 	io_request->raid_bypass = raid_bypass;
 
 	request = io_request->iu;
-	memset(request, 0, offsetof(struct pqi_raid_path_request, sg_descriptors));
+	memset(request, 0, offsetof(struct pqi_aio_path_request, sg_descriptors));
 
 	request->header.iu_type = PQI_REQUEST_IU_AIO_PATH_IO;
 	put_unaligned_le32(aio_handle, &request->nexus_id);
 	put_unaligned_le32(scsi_bufflen(scmd), &request->buffer_length);
 	request->task_attribute = SOP_TASK_ATTRIBUTE_SIMPLE;
+	request->command_priority = io_high_prio;
 	put_unaligned_le16(io_request->index, &request->request_id);
 	request->error_index = request->request_id;
+	if (!pqi_is_logical_device(device) && ctrl_info->multi_lun_device_supported)
+		put_unaligned_le64(((scmd->device->lun) << 8), &request->lun_number);
 	if (cdb_length > sizeof(request->cdb))
 		cdb_length = sizeof(request->cdb);
 	request->cdb_length = cdb_length;
@@ -5449,7 +5768,10 @@
 	struct pqi_io_request *io_request;
 	struct pqi_aio_r1_path_request *r1_request;
 
-	io_request = pqi_alloc_io_request(ctrl_info);
+	io_request = pqi_alloc_io_request(ctrl_info, scmd);
+	if (!io_request)
+		return SCSI_MLQUEUE_HOST_BUSY;
+
 	io_request->io_complete_callback = pqi_aio_io_complete;
 	io_request->scmd = scmd;
 	io_request->raid_bypass = true;
@@ -5507,7 +5829,9 @@
 	struct pqi_io_request *io_request;
 	struct pqi_aio_r56_path_request *r56_request;
 
-	io_request = pqi_alloc_io_request(ctrl_info);
+	io_request = pqi_alloc_io_request(ctrl_info, scmd);
+	if (!io_request)
+		return SCSI_MLQUEUE_HOST_BUSY;
 	io_request->io_complete_callback = pqi_aio_io_complete;
 	io_request->scmd = scmd;
 	io_request->raid_bypass = true;
@@ -5566,13 +5890,10 @@
 static inline u16 pqi_get_hw_queue(struct pqi_ctrl_info *ctrl_info,
 	struct scsi_cmnd *scmd)
 {
-	u16 hw_queue;
-
-	hw_queue = blk_mq_unique_tag_to_hwq(blk_mq_unique_tag(scsi_cmd_to_rq(scmd)));
-	if (hw_queue > ctrl_info->max_hw_queue_index)
-		hw_queue = 0;
-
-	return hw_queue;
+	/*
+	 * We are setting host_tagset = 1 during init.
+	 */
+	return blk_mq_unique_tag_to_hwq(blk_mq_unique_tag(scsi_cmd_to_rq(scmd)));
 }
 
 static inline bool pqi_is_bypass_eligible_request(struct scsi_cmnd *scmd)
@@ -5580,7 +5901,7 @@
 	if (blk_rq_is_passthrough(scsi_cmd_to_rq(scmd)))
 		return false;
 
-	return scmd->SCp.this_residual == 0;
+	return pqi_cmd_priv(scmd)->this_residual == 0;
 }
 
 /*
@@ -5603,7 +5924,7 @@
 		return;
 	}
 
-	atomic_dec(&device->scsi_cmds_outstanding);
+	atomic_dec(&device->scsi_cmds_outstanding[scmd->device->lun]);
 }
 
 static bool pqi_is_parity_write_stream(struct pqi_ctrl_info *ctrl_info,
@@ -5615,7 +5936,7 @@
 	int rc;
 	struct pqi_scsi_dev *device;
 	struct pqi_stream_data *pqi_stream_data;
-	struct pqi_scsi_dev_raid_map_data rmd;
+	struct pqi_scsi_dev_raid_map_data rmd = { 0 };
 
 	if (!ctrl_info->enable_stream_detection)
 		return false;
@@ -5698,7 +6019,7 @@
 		return 0;
 	}
 
-	atomic_inc(&device->scsi_cmds_outstanding);
+	atomic_inc(&device->scsi_cmds_outstanding[scmd->device->lun]);
 
 	ctrl_info = shost_to_hba(shost);
 
@@ -5744,69 +6065,96 @@
 
 out:
 	if (rc)
-		atomic_dec(&device->scsi_cmds_outstanding);
+		atomic_dec(&device->scsi_cmds_outstanding[scmd->device->lun]);
 
 	return rc;
 }
 
-static int pqi_wait_until_queued_io_drained(struct pqi_ctrl_info *ctrl_info,
-	struct pqi_queue_group *queue_group)
+static unsigned int pqi_queued_io_count(struct pqi_ctrl_info *ctrl_info)
 {
+	unsigned int i;
 	unsigned int path;
 	unsigned long flags;
-	bool list_is_empty;
+	unsigned int queued_io_count;
+	struct pqi_queue_group *queue_group;
+	struct pqi_io_request *io_request;
 
-	for (path = 0; path < 2; path++) {
-		while (1) {
-			spin_lock_irqsave(
-				&queue_group->submit_lock[path], flags);
-			list_is_empty =
-				list_empty(&queue_group->request_list[path]);
-			spin_unlock_irqrestore(
-				&queue_group->submit_lock[path], flags);
-			if (list_is_empty)
-				break;
-			pqi_check_ctrl_health(ctrl_info);
-			if (pqi_ctrl_offline(ctrl_info))
-				return -ENXIO;
-			usleep_range(1000, 2000);
+	queued_io_count = 0;
+
+	for (i = 0; i < ctrl_info->num_queue_groups; i++) {
+		queue_group = &ctrl_info->queue_groups[i];
+		for (path = 0; path < 2; path++) {
+			spin_lock_irqsave(&queue_group->submit_lock[path], flags);
+			list_for_each_entry(io_request, &queue_group->request_list[path], request_list_entry)
+				queued_io_count++;
+			spin_unlock_irqrestore(&queue_group->submit_lock[path], flags);
 		}
 	}
 
-	return 0;
+	return queued_io_count;
 }
 
-static int pqi_wait_until_inbound_queues_empty(struct pqi_ctrl_info *ctrl_info)
+static unsigned int pqi_nonempty_inbound_queue_count(struct pqi_ctrl_info *ctrl_info)
 {
-	int rc;
 	unsigned int i;
 	unsigned int path;
+	unsigned int nonempty_inbound_queue_count;
 	struct pqi_queue_group *queue_group;
 	pqi_index_t iq_pi;
 	pqi_index_t iq_ci;
 
+	nonempty_inbound_queue_count = 0;
+
 	for (i = 0; i < ctrl_info->num_queue_groups; i++) {
 		queue_group = &ctrl_info->queue_groups[i];
-
-		rc = pqi_wait_until_queued_io_drained(ctrl_info, queue_group);
-		if (rc)
-			return rc;
-
 		for (path = 0; path < 2; path++) {
 			iq_pi = queue_group->iq_pi_copy[path];
+			iq_ci = readl(queue_group->iq_ci[path]);
+			if (iq_ci != iq_pi)
+				nonempty_inbound_queue_count++;
+		}
+	}
 
-			while (1) {
-				iq_ci = readl(queue_group->iq_ci[path]);
-				if (iq_ci == iq_pi)
-					break;
-				pqi_check_ctrl_health(ctrl_info);
-				if (pqi_ctrl_offline(ctrl_info))
-					return -ENXIO;
-				usleep_range(1000, 2000);
-			}
+	return nonempty_inbound_queue_count;
+}
+
+#define PQI_INBOUND_QUEUES_NONEMPTY_WARNING_TIMEOUT_SECS	10
+
+static int pqi_wait_until_inbound_queues_empty(struct pqi_ctrl_info *ctrl_info)
+{
+	unsigned long start_jiffies;
+	unsigned long warning_timeout;
+	unsigned int queued_io_count;
+	unsigned int nonempty_inbound_queue_count;
+	bool displayed_warning;
+
+	displayed_warning = false;
+	start_jiffies = jiffies;
+	warning_timeout = (PQI_INBOUND_QUEUES_NONEMPTY_WARNING_TIMEOUT_SECS * HZ) + start_jiffies;
+
+	while (1) {
+		queued_io_count = pqi_queued_io_count(ctrl_info);
+		nonempty_inbound_queue_count = pqi_nonempty_inbound_queue_count(ctrl_info);
+		if (queued_io_count == 0 && nonempty_inbound_queue_count == 0)
+			break;
+		pqi_check_ctrl_health(ctrl_info);
+		if (pqi_ctrl_offline(ctrl_info))
+			return -ENXIO;
+		if (time_after(jiffies, warning_timeout)) {
+			dev_warn(&ctrl_info->pci_dev->dev,
+				"waiting %u seconds for queued I/O to drain (queued I/O count: %u; non-empty inbound queue count: %u)\n",
+				jiffies_to_msecs(jiffies - start_jiffies) / 1000, queued_io_count, nonempty_inbound_queue_count);
+			displayed_warning = true;
+			warning_timeout = (PQI_INBOUND_QUEUES_NONEMPTY_WARNING_TIMEOUT_SECS * HZ) + jiffies;
 		}
+		usleep_range(1000, 2000);
 	}
 
+	if (displayed_warning)
+		dev_warn(&ctrl_info->pci_dev->dev,
+			"queued I/O drained after waiting for %u seconds\n",
+			jiffies_to_msecs(jiffies - start_jiffies) / 1000);
+
 	return 0;
 }
 
@@ -5857,7 +6205,7 @@
 #define PQI_PENDING_IO_WARNING_TIMEOUT_SECS	10
 
 static int pqi_device_wait_for_pending_io(struct pqi_ctrl_info *ctrl_info,
-	struct pqi_scsi_dev *device, unsigned long timeout_msecs)
+	struct pqi_scsi_dev *device, u8 lun, unsigned long timeout_msecs)
 {
 	int cmds_outstanding;
 	unsigned long start_jiffies;
@@ -5865,26 +6213,28 @@
 	unsigned long msecs_waiting;
 
 	start_jiffies = jiffies;
-	warning_timeout = (PQI_PENDING_IO_WARNING_TIMEOUT_SECS * PQI_HZ) + start_jiffies;
+	warning_timeout = (PQI_PENDING_IO_WARNING_TIMEOUT_SECS * HZ) + start_jiffies;
 
-	while ((cmds_outstanding = atomic_read(&device->scsi_cmds_outstanding)) > 0) {
-		pqi_check_ctrl_health(ctrl_info);
-		if (pqi_ctrl_offline(ctrl_info))
-			return -ENXIO;
+	while ((cmds_outstanding = atomic_read(&device->scsi_cmds_outstanding[lun])) > 0) {
+		if (ctrl_info->ctrl_removal_state != PQI_CTRL_GRACEFUL_REMOVAL) {
+			pqi_check_ctrl_health(ctrl_info);
+			if (pqi_ctrl_offline(ctrl_info))
+				return -ENXIO;
+		}
 		msecs_waiting = jiffies_to_msecs(jiffies - start_jiffies);
-		if (msecs_waiting > timeout_msecs) {
+		if (msecs_waiting >= timeout_msecs) {
 			dev_err(&ctrl_info->pci_dev->dev,
 				"scsi %d:%d:%d:%d: timed out after %lu seconds waiting for %d outstanding command(s)\n",
 				ctrl_info->scsi_host->host_no, device->bus, device->target,
-				device->lun, msecs_waiting / 1000, cmds_outstanding);
+				lun, msecs_waiting / 1000, cmds_outstanding);
 			return -ETIMEDOUT;
 		}
 		if (time_after(jiffies, warning_timeout)) {
 			dev_warn(&ctrl_info->pci_dev->dev,
 				"scsi %d:%d:%d:%d: waiting %lu seconds for %d outstanding command(s)\n",
 				ctrl_info->scsi_host->host_no, device->bus, device->target,
-				device->lun, msecs_waiting / 1000, cmds_outstanding);
-			warning_timeout = (PQI_PENDING_IO_WARNING_TIMEOUT_SECS * PQI_HZ) + jiffies;
+				lun, msecs_waiting / 1000, cmds_outstanding);
+			warning_timeout = (PQI_PENDING_IO_WARNING_TIMEOUT_SECS * HZ) + jiffies;
 		}
 		usleep_range(1000, 2000);
 	}
@@ -5903,16 +6253,17 @@
 #define PQI_LUN_RESET_POLL_COMPLETION_SECS	10
 
 static int pqi_wait_for_lun_reset_completion(struct pqi_ctrl_info *ctrl_info,
-	struct pqi_scsi_dev *device, struct completion *wait)
+	struct pqi_scsi_dev *device, u8 lun, struct completion *wait)
 {
 	int rc;
 	unsigned int wait_secs;
+	int cmds_outstanding;
 
 	wait_secs = 0;
 
 	while (1) {
 		if (wait_for_completion_io_timeout(wait,
-			PQI_LUN_RESET_POLL_COMPLETION_SECS * PQI_HZ)) {
+			PQI_LUN_RESET_POLL_COMPLETION_SECS * HZ)) {
 			rc = 0;
 			break;
 		}
@@ -5924,11 +6275,10 @@
 		}
 
 		wait_secs += PQI_LUN_RESET_POLL_COMPLETION_SECS;
-
+		cmds_outstanding = atomic_read(&device->scsi_cmds_outstanding[lun]);
 		dev_warn(&ctrl_info->pci_dev->dev,
-			"scsi %d:%d:%d:%d: waiting %u seconds for LUN reset to complete\n",
-			ctrl_info->scsi_host->host_no, device->bus, device->target, device->lun,
-			wait_secs);
+			"scsi %d:%d:%d:%d: waiting %u seconds for LUN reset to complete (%d command(s) outstanding)\n",
+			ctrl_info->scsi_host->host_no, device->bus, device->target, lun, wait_secs, cmds_outstanding);
 	}
 
 	return rc;
@@ -5936,14 +6286,16 @@
 
 #define PQI_LUN_RESET_FIRMWARE_TIMEOUT_SECS	30
 
-static int pqi_lun_reset(struct pqi_ctrl_info *ctrl_info, struct pqi_scsi_dev *device)
+static int pqi_lun_reset(struct pqi_ctrl_info *ctrl_info, struct scsi_cmnd *scmd)
 {
 	int rc;
 	struct pqi_io_request *io_request;
 	DECLARE_COMPLETION_ONSTACK(wait);
 	struct pqi_task_management_request *request;
+	struct pqi_scsi_dev *device;
 
-	io_request = pqi_alloc_io_request(ctrl_info);
+	device = scmd->device->hostdata;
+	io_request = pqi_alloc_io_request(ctrl_info, NULL);
 	io_request->io_complete_callback = pqi_lun_reset_complete;
 	io_request->context = &wait;
 
@@ -5956,6 +6308,8 @@
 	put_unaligned_le16(io_request->index, &request->request_id);
 	memcpy(request->lun_number, device->scsi3addr,
 		sizeof(request->lun_number));
+	if (!pqi_is_logical_device(device) && ctrl_info->multi_lun_device_supported)
+		request->ml_device_lun_number = (u8)scmd->device->lun;
 	request->task_management_function = SOP_TASK_MANAGEMENT_LUN_RESET;
 	if (ctrl_info->tmf_iu_timeout_supported)
 		put_unaligned_le16(PQI_LUN_RESET_FIRMWARE_TIMEOUT_SECS, &request->timeout);
@@ -5963,7 +6317,7 @@
 	pqi_start_io(ctrl_info, &ctrl_info->queue_groups[PQI_DEFAULT_QUEUE_GROUP], RAID_PATH,
 		io_request);
 
-	rc = pqi_wait_for_lun_reset_completion(ctrl_info, device, &wait);
+	rc = pqi_wait_for_lun_reset_completion(ctrl_info, device, (u8)scmd->device->lun, &wait);
 	if (rc == 0)
 		rc = io_request->status;
 
@@ -5977,16 +6331,18 @@
 #define PQI_LUN_RESET_PENDING_IO_TIMEOUT_MSECS		(10 * 60 * 1000)
 #define PQI_LUN_RESET_FAILED_PENDING_IO_TIMEOUT_MSECS	(2 * 60 * 1000)
 
-static int pqi_lun_reset_with_retries(struct pqi_ctrl_info *ctrl_info, struct pqi_scsi_dev *device)
+static int pqi_lun_reset_with_retries(struct pqi_ctrl_info *ctrl_info, struct scsi_cmnd *scmd)
 {
 	int reset_rc;
 	int wait_rc;
 	unsigned int retries;
 	unsigned long timeout_msecs;
+	struct pqi_scsi_dev *device;
 
+	device = scmd->device->hostdata;
 	for (retries = 0;;) {
-		reset_rc = pqi_lun_reset(ctrl_info, device);
-		if (reset_rc == 0 || ++retries > PQI_LUN_RESET_RETRIES)
+		reset_rc = pqi_lun_reset(ctrl_info, scmd);
+		if (reset_rc == 0 || reset_rc == -ENODEV || ++retries > PQI_LUN_RESET_RETRIES)
 			break;
 		msleep(PQI_LUN_RESET_RETRY_INTERVAL_MSECS);
 	}
@@ -5994,18 +6350,19 @@
 	timeout_msecs = reset_rc ? PQI_LUN_RESET_FAILED_PENDING_IO_TIMEOUT_MSECS :
 		PQI_LUN_RESET_PENDING_IO_TIMEOUT_MSECS;
 
-	wait_rc = pqi_device_wait_for_pending_io(ctrl_info, device, timeout_msecs);
+	wait_rc = pqi_device_wait_for_pending_io(ctrl_info, device, scmd->device->lun, timeout_msecs);
 	if (wait_rc && reset_rc == 0)
 		reset_rc = wait_rc;
 
 	return reset_rc == 0 ? SUCCESS : FAILED;
 }
 
-static int pqi_device_reset(struct pqi_ctrl_info *ctrl_info,
-	struct pqi_scsi_dev *device)
+static int pqi_device_reset(struct pqi_ctrl_info *ctrl_info, struct scsi_cmnd *scmd)
 {
 	int rc;
+	struct pqi_scsi_dev *device;
 
+	device = scmd->device->hostdata;
 	pqi_ctrl_block_requests(ctrl_info);
 	pqi_ctrl_wait_until_quiesced(ctrl_info);
 	pqi_fail_io_queued_for_device(ctrl_info, device);
@@ -6013,7 +6370,7 @@
 	if (rc)
 		rc = FAILED;
 	else
-		rc = pqi_lun_reset_with_retries(ctrl_info, device);
+		rc = pqi_lun_reset_with_retries(ctrl_info, scmd);
 	pqi_ctrl_unblock_requests(ctrl_info);
 
 	return rc;
@@ -6035,18 +6392,18 @@
 	dev_err(&ctrl_info->pci_dev->dev,
 		"resetting scsi %d:%d:%d:%d due to cmd 0x%02x\n",
 		shost->host_no,
-		device->bus, device->target, device->lun,
+		device->bus, device->target, (u32)scmd->device->lun,
 		scmd->cmd_len > 0 ? scmd->cmnd[0] : 0xff);
 
 	pqi_check_ctrl_health(ctrl_info);
 	if (pqi_ctrl_offline(ctrl_info))
 		rc = FAILED;
 	else
-		rc = pqi_device_reset(ctrl_info, device);
+		rc = pqi_device_reset(ctrl_info, scmd);
 
 	dev_err(&ctrl_info->pci_dev->dev,
 		"reset of scsi %d:%d:%d:%d: %s\n",
-		shost->host_no, device->bus, device->target, device->lun,
+		shost->host_no, device->bus, device->target, (u32)scmd->device->lun,
 		rc == SUCCESS ? "SUCCESS" : "FAILED");
 
 	mutex_unlock(&ctrl_info->lun_reset_mutex);
@@ -6071,9 +6428,13 @@
 		rphy = target_to_rphy(starget);
 		device = pqi_find_device_by_sas_rphy(ctrl_info, rphy);
 		if (device) {
-			device->target = sdev_id(sdev);
-			device->lun = sdev->lun;
-			device->target_lun_valid = true;
+			if (device->target_lun_valid) {
+				device->ignore_device = true;
+			} else {
+				device->target = sdev_id(sdev);
+				device->lun = sdev->lun;
+				device->target_lun_valid = true;
+			}
 		}
 	} else {
 		device = pqi_find_scsi_dev(ctrl_info, sdev_channel(sdev),
@@ -6110,39 +6471,60 @@
 					ctrl_info->pci_dev, 0);
 }
 
+static inline bool pqi_is_tape_changer_device(struct pqi_scsi_dev *device)
+{
+	return device->devtype == TYPE_TAPE || device->devtype == TYPE_MEDIUM_CHANGER;
+}
+
 static int pqi_slave_configure(struct scsi_device *sdev)
 {
+	int rc = 0;
 	struct pqi_scsi_dev *device;
 
 	device = sdev->hostdata;
 	device->devtype = sdev->type;
 
-	return 0;
+	if (pqi_is_tape_changer_device(device) && device->ignore_device) {
+		rc = -ENXIO;
+		device->ignore_device = false;
+	}
+
+	return rc;
 }
 
 static void pqi_slave_destroy(struct scsi_device *sdev)
 {
-	unsigned long flags;
-	struct pqi_scsi_dev *device;
 	struct pqi_ctrl_info *ctrl_info;
+	struct pqi_scsi_dev *device;
+	int mutex_acquired;
+	unsigned long flags;
 
 	ctrl_info = shost_to_hba(sdev->host);
 
-	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
+	mutex_acquired = mutex_trylock(&ctrl_info->scan_mutex);
+	if (!mutex_acquired)
+		return;
 
 	device = sdev->hostdata;
-	if (device) {
-		sdev->hostdata = NULL;
-		if (!list_empty(&device->scsi_device_list_entry))
-			list_del(&device->scsi_device_list_entry);
+	if (!device) {
+		mutex_unlock(&ctrl_info->scan_mutex);
+		return;
 	}
 
+	device->lun_count--;
+	if (device->lun_count > 0) {
+		mutex_unlock(&ctrl_info->scan_mutex);
+		return;
+	}
+
+	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
+	list_del(&device->scsi_device_list_entry);
 	spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
 
-	if (device) {
-		pqi_dev_info(ctrl_info, "removed", device);
-		pqi_free_device(device);
-	}
+	mutex_unlock(&ctrl_info->scan_mutex);
+
+	pqi_dev_info(ctrl_info, "removed", device);
+	pqi_free_device(device);
 }
 
 static int pqi_getpciinfo_ioctl(struct pqi_ctrl_info *ctrl_info, void __user *arg)
@@ -6631,20 +7013,22 @@
 static DEVICE_ATTR(enable_r6_writes, 0644,
 	pqi_host_enable_r6_writes_show, pqi_host_enable_r6_writes_store);
 
-static struct device_attribute *pqi_shost_attrs[] = {
-	&dev_attr_driver_version,
-	&dev_attr_firmware_version,
-	&dev_attr_model,
-	&dev_attr_serial_number,
-	&dev_attr_vendor,
-	&dev_attr_rescan,
-	&dev_attr_lockup_action,
-	&dev_attr_enable_stream_detection,
-	&dev_attr_enable_r5_writes,
-	&dev_attr_enable_r6_writes,
+static struct attribute *pqi_shost_attrs[] = {
+	&dev_attr_driver_version.attr,
+	&dev_attr_firmware_version.attr,
+	&dev_attr_model.attr,
+	&dev_attr_serial_number.attr,
+	&dev_attr_vendor.attr,
+	&dev_attr_rescan.attr,
+	&dev_attr_lockup_action.attr,
+	&dev_attr_enable_stream_detection.attr,
+	&dev_attr_enable_r5_writes.attr,
+	&dev_attr_enable_r6_writes.attr,
 	NULL
 };
 
+ATTRIBUTE_GROUPS(pqi_shost);
+
 static ssize_t pqi_unique_id_show(struct device *dev,
 	struct device_attribute *attr, char *buffer)
 {
@@ -6657,6 +7041,9 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
@@ -6665,12 +7052,10 @@
 		return -ENODEV;
 	}
 
-	if (device->is_physical_device) {
-		memset(unique_id, 0, 8);
-		memcpy(unique_id + 8, &device->wwid, sizeof(device->wwid));
-	} else {
+	if (device->is_physical_device)
+		memcpy(unique_id, device->wwid, sizeof(device->wwid));
+	else
 		memcpy(unique_id, device->volume_id, sizeof(device->volume_id));
-	}
 
 	spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
 
@@ -6695,6 +7080,9 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
@@ -6730,6 +7118,9 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
@@ -6807,10 +7198,13 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
-	if (!device || !pqi_is_device_with_sas_address(device)) {
+	if (!device) {
 		spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
 		return -ENODEV;
 	}
@@ -6833,6 +7227,9 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
@@ -6862,6 +7259,9 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
@@ -6870,7 +7270,7 @@
 		return -ENODEV;
 	}
 
-	if (pqi_is_logical_device(device))
+	if (pqi_is_logical_device(device) && device->devtype == TYPE_DISK)
 		raid_level = pqi_raid_level_to_string(device->raid_level);
 	else
 		raid_level = "N/A";
@@ -6892,6 +7292,9 @@
 	sdev = to_scsi_device(dev);
 	ctrl_info = shost_to_hba(sdev->host);
 
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
 	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
 
 	device = sdev->hostdata;
@@ -6907,6 +7310,74 @@
 	return scnprintf(buffer, PAGE_SIZE, "0x%x\n", raid_bypass_cnt);
 }
 
+static ssize_t pqi_sas_ncq_prio_enable_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct pqi_ctrl_info *ctrl_info;
+	struct scsi_device *sdev;
+	struct pqi_scsi_dev *device;
+	unsigned long flags;
+	int output_len = 0;
+
+	sdev = to_scsi_device(dev);
+	ctrl_info = shost_to_hba(sdev->host);
+
+	if (pqi_ctrl_offline(ctrl_info))
+		return -ENODEV;
+
+	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
+
+	device = sdev->hostdata;
+	if (!device) {
+		spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
+		return -ENODEV;
+	}
+
+	output_len = snprintf(buf, PAGE_SIZE, "%d\n",
+				device->ncq_prio_enable);
+	spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
+
+	return output_len;
+}
+
+static ssize_t pqi_sas_ncq_prio_enable_store(struct device *dev,
+			struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+	struct pqi_ctrl_info *ctrl_info;
+	struct scsi_device *sdev;
+	struct pqi_scsi_dev *device;
+	unsigned long flags;
+	u8 ncq_prio_enable = 0;
+
+	if (kstrtou8(buf, 0, &ncq_prio_enable))
+		return -EINVAL;
+
+	sdev = to_scsi_device(dev);
+	ctrl_info = shost_to_hba(sdev->host);
+
+	spin_lock_irqsave(&ctrl_info->scsi_device_list_lock, flags);
+
+	device = sdev->hostdata;
+
+	if (!device) {
+		spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
+		return -ENODEV;
+	}
+
+	if (!device->ncq_prio_support ||
+		!device->is_physical_device) {
+		spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
+		return -EINVAL;
+	}
+
+	device->ncq_prio_enable = ncq_prio_enable;
+
+	spin_unlock_irqrestore(&ctrl_info->scsi_device_list_lock, flags);
+
+	return  strlen(buf);
+}
+
 static DEVICE_ATTR(lunid, 0444, pqi_lunid_show, NULL);
 static DEVICE_ATTR(unique_id, 0444, pqi_unique_id_show, NULL);
 static DEVICE_ATTR(path_info, 0444, pqi_path_info_show, NULL);
@@ -6914,18 +7385,23 @@
 static DEVICE_ATTR(ssd_smart_path_enabled, 0444, pqi_ssd_smart_path_enabled_show, NULL);
 static DEVICE_ATTR(raid_level, 0444, pqi_raid_level_show, NULL);
 static DEVICE_ATTR(raid_bypass_cnt, 0444, pqi_raid_bypass_cnt_show, NULL);
+static DEVICE_ATTR(sas_ncq_prio_enable, 0644,
+		pqi_sas_ncq_prio_enable_show, pqi_sas_ncq_prio_enable_store);
 
-static struct device_attribute *pqi_sdev_attrs[] = {
-	&dev_attr_lunid,
-	&dev_attr_unique_id,
-	&dev_attr_path_info,
-	&dev_attr_sas_address,
-	&dev_attr_ssd_smart_path_enabled,
-	&dev_attr_raid_level,
-	&dev_attr_raid_bypass_cnt,
+static struct attribute *pqi_sdev_attrs[] = {
+	&dev_attr_lunid.attr,
+	&dev_attr_unique_id.attr,
+	&dev_attr_path_info.attr,
+	&dev_attr_sas_address.attr,
+	&dev_attr_ssd_smart_path_enabled.attr,
+	&dev_attr_raid_level.attr,
+	&dev_attr_raid_bypass_cnt.attr,
+	&dev_attr_sas_ncq_prio_enable.attr,
 	NULL
 };
 
+ATTRIBUTE_GROUPS(pqi_sdev);
+
 static struct scsi_host_template pqi_driver_template = {
 	.module = THIS_MODULE,
 	.name = DRIVER_NAME_SHORT,
@@ -6940,8 +7416,8 @@
 	.slave_configure = pqi_slave_configure,
 	.slave_destroy = pqi_slave_destroy,
 	.map_queues = pqi_map_queues,
-	.sdev_attrs = pqi_sdev_attrs,
-	.shost_attrs = pqi_shost_attrs,
+	.sdev_groups = pqi_sdev_groups,
+	.cmd_size = sizeof(struct pqi_cmd_priv),
 };
 
 static int pqi_register_scsi(struct pqi_ctrl_info *ctrl_info)
@@ -6960,7 +7436,7 @@
 	shost->this_id = -1;
 	shost->max_channel = PQI_MAX_BUS;
 	shost->max_cmd_len = MAX_COMMAND_SIZE;
-	shost->max_lun = ~0;
+	shost->max_lun = PQI_MAX_LUNS_PER_DEVICE;
 	shost->max_id = ~0;
 	shost->max_sectors = ctrl_info->max_sectors;
 	shost->can_queue = ctrl_info->scsi_ml_can_queue;
@@ -7028,8 +7504,7 @@
 		reset_reg.all_bits = readl(&pqi_registers->device_reset);
 		if (reset_reg.bits.reset_action == PQI_RESET_ACTION_COMPLETED)
 			break;
-		pqi_check_ctrl_health(ctrl_info);
-		if (pqi_ctrl_offline(ctrl_info)) {
+		if (!sis_is_firmware_running(ctrl_info)) {
 			rc = -ENXIO;
 			break;
 		}
@@ -7133,6 +7608,9 @@
 		sizeof(identify->vendor_id));
 	ctrl_info->vendor[sizeof(identify->vendor_id)] = '\0';
 
+	dev_info(&ctrl_info->pci_dev->dev,
+		"Firmware version: %s\n", ctrl_info->firmware_version);
+
 out:
 	kfree(identify);
 
@@ -7297,9 +7775,15 @@
 	case PQI_FIRMWARE_FEATURE_TMF_IU_TIMEOUT:
 		ctrl_info->tmf_iu_timeout_supported = firmware_feature->enabled;
 		break;
-	case PQI_FIRMWARE_FEATURE_UNIQUE_WWID_IN_REPORT_PHYS_LUN:
-		ctrl_info->unique_wwid_in_report_phys_lun_supported =
-			firmware_feature->enabled;
+	case PQI_FIRMWARE_FEATURE_FW_TRIAGE:
+		ctrl_info->firmware_triage_supported = firmware_feature->enabled;
+		pqi_save_fw_triage_setting(ctrl_info, firmware_feature->enabled);
+		break;
+	case PQI_FIRMWARE_FEATURE_RPL_EXTENDED_FORMAT_4_5:
+		ctrl_info->rpl_extended_format_4_5_supported = firmware_feature->enabled;
+		break;
+	case PQI_FIRMWARE_FEATURE_MULTI_LUN_DEVICE_SUPPORT:
+		ctrl_info->multi_lun_device_supported = firmware_feature->enabled;
 		break;
 	}
 
@@ -7392,8 +7876,18 @@
 		.feature_status = pqi_firmware_feature_status,
 	},
 	{
-		.feature_name = "Unique WWID in Report Physical LUN",
-		.feature_bit = PQI_FIRMWARE_FEATURE_UNIQUE_WWID_IN_REPORT_PHYS_LUN,
+		.feature_name = "Firmware Triage",
+		.feature_bit = PQI_FIRMWARE_FEATURE_FW_TRIAGE,
+		.feature_status = pqi_ctrl_update_feature_flags,
+	},
+	{
+		.feature_name = "RPL Extended Formats 4 and 5",
+		.feature_bit = PQI_FIRMWARE_FEATURE_RPL_EXTENDED_FORMAT_4_5,
+		.feature_status = pqi_ctrl_update_feature_flags,
+	},
+	{
+		.feature_name = "Multi-LUN Target",
+		.feature_bit = PQI_FIRMWARE_FEATURE_MULTI_LUN_DEVICE_SUPPORT,
 		.feature_status = pqi_ctrl_update_feature_flags,
 	},
 };
@@ -7495,7 +7989,9 @@
 	ctrl_info->enable_r6_writes = false;
 	ctrl_info->raid_iu_timeout_supported = false;
 	ctrl_info->tmf_iu_timeout_supported = false;
-	ctrl_info->unique_wwid_in_report_phys_lun_supported = false;
+	ctrl_info->firmware_triage_supported = false;
+	ctrl_info->rpl_extended_format_4_5_supported = false;
+	ctrl_info->multi_lun_device_supported = false;
 }
 
 static int pqi_process_config_table(struct pqi_ctrl_info *ctrl_info)
@@ -7507,7 +8003,7 @@
 	struct pqi_config_table *config_table;
 	struct pqi_config_table_section_header *section;
 	struct pqi_config_table_section_info section_info;
-	struct pqi_config_table_section_info feature_section_info;
+	struct pqi_config_table_section_info feature_section_info = {0};
 
 	table_length = ctrl_info->config_table_length;
 	if (table_length == 0)
@@ -7621,14 +8117,34 @@
 	return pqi_revert_to_sis_mode(ctrl_info);
 }
 
+static void pqi_perform_lockup_action(void)
+{
+	switch (pqi_lockup_action) {
+	case PANIC:
+		panic("FATAL: Smart Family Controller lockup detected");
+		break;
+	case REBOOT:
+		emergency_restart();
+		break;
+	case NONE:
+	default:
+		break;
+	}
+}
+
 static int pqi_ctrl_init(struct pqi_ctrl_info *ctrl_info)
 {
 	int rc;
 	u32 product_id;
 
 	if (reset_devices) {
+		if (pqi_is_fw_triage_supported(ctrl_info)) {
+			rc = sis_wait_for_fw_triage_completion(ctrl_info);
+			if (rc)
+				return rc;
+		}
 		sis_soft_reset(ctrl_info);
-		msleep(PQI_POST_RESET_DELAY_SECS * PQI_HZ);
+		ssleep(PQI_POST_RESET_DELAY_SECS);
 	} else {
 		rc = pqi_force_sis_mode(ctrl_info);
 		if (rc)
@@ -7640,8 +8156,15 @@
 	 * commands.
 	 */
 	rc = sis_wait_for_ctrl_ready(ctrl_info);
-	if (rc)
+	if (rc) {
+		if (reset_devices) {
+			dev_err(&ctrl_info->pci_dev->dev,
+				"kdump init failed with error %d\n", rc);
+			pqi_lockup_action = REBOOT;
+			pqi_perform_lockup_action();
+		}
 		return rc;
+	}
 
 	/*
 	 * Get the controller properties.  This allows us to determine
@@ -8125,6 +8648,7 @@
 	ctrl_info->max_write_raid_5_6 = PQI_DEFAULT_MAX_WRITE_RAID_5_6;
 	ctrl_info->max_write_raid_1_10_2drive = ~0;
 	ctrl_info->max_write_raid_1_10_3drive = ~0;
+	ctrl_info->disable_managed_interrupts = pqi_disable_managed_interrupts;
 
 	return ctrl_info;
 }
@@ -8142,7 +8666,6 @@
 
 static void pqi_free_ctrl_resources(struct pqi_ctrl_info *ctrl_info)
 {
-	pqi_stop_heartbeat_timer(ctrl_info);
 	pqi_free_interrupts(ctrl_info);
 	if (ctrl_info->queue_memory_base)
 		dma_free_coherent(&ctrl_info->pci_dev->dev,
@@ -8167,8 +8690,15 @@
 
 static void pqi_remove_ctrl(struct pqi_ctrl_info *ctrl_info)
 {
+	ctrl_info->controller_online = false;
+	pqi_stop_heartbeat_timer(ctrl_info);
+	pqi_ctrl_block_requests(ctrl_info);
 	pqi_cancel_rescan_worker(ctrl_info);
 	pqi_cancel_update_time_worker(ctrl_info);
+	if (ctrl_info->ctrl_removal_state == PQI_CTRL_SURPRISE_REMOVAL) {
+		pqi_fail_all_outstanding_requests(ctrl_info);
+		ctrl_info->pqi_mode_enabled = false;
+	}
 	pqi_unregister_scsi(ctrl_info);
 	if (ctrl_info->pqi_mode_enabled)
 		pqi_revert_to_sis_mode(ctrl_info);
@@ -8365,21 +8895,6 @@
 	return pqi_ctrl_init_resume(ctrl_info);
 }
 
-static void pqi_perform_lockup_action(void)
-{
-	switch (pqi_lockup_action) {
-	case PANIC:
-		panic("FATAL: Smart Family Controller lockup detected");
-		break;
-	case REBOOT:
-		emergency_restart();
-		break;
-	case NONE:
-	default:
-		break;
-	}
-}
-
 static struct pqi_raid_error_info pqi_ctrl_offline_raid_error_info = {
 	.data_out_result = PQI_DATA_IN_OUT_HARDWARE_ERROR,
 	.status = SAM_STAT_CHECK_CONDITION,
@@ -8390,6 +8905,7 @@
 	unsigned int i;
 	struct pqi_io_request *io_request;
 	struct scsi_cmnd *scmd;
+	struct scsi_device *sdev;
 
 	for (i = 0; i < ctrl_info->max_io_slots; i++) {
 		io_request = &ctrl_info->io_request_pool[i];
@@ -8398,7 +8914,13 @@
 
 		scmd = io_request->scmd;
 		if (scmd) {
-			set_host_byte(scmd, DID_NO_CONNECT);
+			sdev = scmd->device;
+			if (!sdev || !scsi_device_online(sdev)) {
+				pqi_free_io_request(io_request);
+				continue;
+			} else {
+				set_host_byte(scmd, DID_NO_CONNECT);
+			}
 		} else {
 			io_request->status = -ENXIO;
 			io_request->error_info =
@@ -8430,7 +8952,8 @@
 	pqi_take_ctrl_offline_deferred(ctrl_info);
 }
 
-static void pqi_take_ctrl_offline(struct pqi_ctrl_info *ctrl_info)
+static void pqi_take_ctrl_offline(struct pqi_ctrl_info *ctrl_info,
+	enum pqi_ctrl_shutdown_reason ctrl_shutdown_reason)
 {
 	if (!ctrl_info->controller_online)
 		return;
@@ -8439,7 +8962,7 @@
 	ctrl_info->pqi_mode_enabled = false;
 	pqi_ctrl_block_requests(ctrl_info);
 	if (!pqi_disable_ctrl_shutdown)
-		sis_shutdown_ctrl(ctrl_info);
+		sis_shutdown_ctrl(ctrl_info, ctrl_shutdown_reason);
 	pci_disable_device(ctrl_info->pci_dev);
 	dev_err(&ctrl_info->pci_dev->dev, "controller offline\n");
 	schedule_work(&ctrl_info->ctrl_offline_work);
@@ -8462,7 +8985,7 @@
 	const struct pci_device_id *id)
 {
 	int rc;
-	int node, cp_node;
+	int node;
 	struct pqi_ctrl_info *ctrl_info;
 
 	pqi_print_ctrl_info(pci_dev, id);
@@ -8481,10 +9004,10 @@
 
 	node = dev_to_node(&pci_dev->dev);
 	if (node == NUMA_NO_NODE) {
-		cp_node = cpu_to_node(0);
-		if (cp_node == NUMA_NO_NODE)
-			cp_node = 0;
-		set_dev_node(&pci_dev->dev, cp_node);
+		node = cpu_to_node(0);
+		if (node == NUMA_NO_NODE)
+			node = 0;
+		set_dev_node(&pci_dev->dev, node);
 	}
 
 	ctrl_info = pqi_alloc_ctrl_info(node);
@@ -8515,11 +9038,26 @@
 static void pqi_pci_remove(struct pci_dev *pci_dev)
 {
 	struct pqi_ctrl_info *ctrl_info;
+	u16 vendor_id;
+	int rc;
 
 	ctrl_info = pci_get_drvdata(pci_dev);
 	if (!ctrl_info)
 		return;
 
+	pci_read_config_word(ctrl_info->pci_dev, PCI_SUBSYSTEM_VENDOR_ID, &vendor_id);
+	if (vendor_id == 0xffff)
+		ctrl_info->ctrl_removal_state = PQI_CTRL_SURPRISE_REMOVAL;
+	else
+		ctrl_info->ctrl_removal_state = PQI_CTRL_GRACEFUL_REMOVAL;
+
+	if (ctrl_info->ctrl_removal_state == PQI_CTRL_GRACEFUL_REMOVAL) {
+		rc = pqi_flush_cache(ctrl_info, RESTART);
+		if (rc)
+			dev_err(&pci_dev->dev,
+				"unable to flush controller cache during remove\n");
+	}
+
 	pqi_remove_ctrl(ctrl_info);
 }
 
@@ -8543,6 +9081,7 @@
 {
 	int rc;
 	struct pqi_ctrl_info *ctrl_info;
+	enum bmic_flush_cache_shutdown_event shutdown_event;
 
 	ctrl_info = pci_get_drvdata(pci_dev);
 	if (!ctrl_info) {
@@ -8558,11 +9097,16 @@
 	pqi_ctrl_block_requests(ctrl_info);
 	pqi_ctrl_wait_until_quiesced(ctrl_info);
 
+	if (system_state == SYSTEM_RESTART)
+		shutdown_event = RESTART;
+	else
+		shutdown_event = SHUTDOWN;
+
 	/*
 	 * Write all data in the controller's battery-backed cache to
 	 * storage.
 	 */
-	rc = pqi_flush_cache(ctrl_info, SHUTDOWN);
+	rc = pqi_flush_cache(ctrl_info, shutdown_event);
 	if (rc)
 		dev_err(&pci_dev->dev,
 			"unable to flush controller cache\n");
@@ -8590,15 +9134,49 @@
 		DRIVER_NAME_SHORT, pqi_lockup_action_param);
 }
 
+#define PQI_CTRL_READY_TIMEOUT_PARAM_MIN_SECS		30
+#define PQI_CTRL_READY_TIMEOUT_PARAM_MAX_SECS		(30 * 60)
+
+static void pqi_process_ctrl_ready_timeout_param(void)
+{
+	if (pqi_ctrl_ready_timeout_secs == 0)
+		return;
+
+	if (pqi_ctrl_ready_timeout_secs < PQI_CTRL_READY_TIMEOUT_PARAM_MIN_SECS) {
+		pr_warn("%s: ctrl_ready_timeout parm of %u second(s) is less than minimum timeout of %d seconds - setting timeout to %d seconds\n",
+			DRIVER_NAME_SHORT, pqi_ctrl_ready_timeout_secs, PQI_CTRL_READY_TIMEOUT_PARAM_MIN_SECS, PQI_CTRL_READY_TIMEOUT_PARAM_MIN_SECS);
+		pqi_ctrl_ready_timeout_secs = PQI_CTRL_READY_TIMEOUT_PARAM_MIN_SECS;
+	} else if (pqi_ctrl_ready_timeout_secs > PQI_CTRL_READY_TIMEOUT_PARAM_MAX_SECS) {
+		pr_warn("%s: ctrl_ready_timeout parm of %u seconds is greater than maximum timeout of %d seconds - setting timeout to %d seconds\n",
+			DRIVER_NAME_SHORT, pqi_ctrl_ready_timeout_secs, PQI_CTRL_READY_TIMEOUT_PARAM_MAX_SECS, PQI_CTRL_READY_TIMEOUT_PARAM_MAX_SECS);
+		pqi_ctrl_ready_timeout_secs = PQI_CTRL_READY_TIMEOUT_PARAM_MAX_SECS;
+	}
+
+	sis_ctrl_ready_timeout_secs = pqi_ctrl_ready_timeout_secs;
+}
+
 static void pqi_process_module_params(void)
 {
 	pqi_process_lockup_action_param();
+	pqi_process_ctrl_ready_timeout_param();
 }
 
-static __maybe_unused int pqi_suspend(struct pci_dev *pci_dev, pm_message_t state)
+#if defined(CONFIG_PM)
+
+static inline enum bmic_flush_cache_shutdown_event pqi_get_flush_cache_shutdown_event(struct pci_dev *pci_dev)
 {
+	if (pci_dev->subsystem_vendor == PCI_VENDOR_ID_ADAPTEC2 && pci_dev->subsystem_device == 0x1304)
+		return RESTART;
+
+	return SUSPEND;
+}
+
+static int pqi_suspend_or_freeze(struct device *dev, bool suspend)
+{
+	struct pci_dev *pci_dev;
 	struct pqi_ctrl_info *ctrl_info;
 
+	pci_dev = to_pci_dev(dev);
 	ctrl_info = pci_get_drvdata(pci_dev);
 
 	pqi_wait_until_ofa_finished(ctrl_info);
@@ -8608,16 +9186,17 @@
 	pqi_ctrl_block_device_reset(ctrl_info);
 	pqi_ctrl_block_requests(ctrl_info);
 	pqi_ctrl_wait_until_quiesced(ctrl_info);
-	pqi_flush_cache(ctrl_info, SUSPEND);
-	pqi_stop_heartbeat_timer(ctrl_info);
 
-	pqi_crash_if_pending_command(ctrl_info);
+	if (suspend) {
+		enum bmic_flush_cache_shutdown_event shutdown_event;
 
-	if (state.event == PM_EVENT_FREEZE)
-		return 0;
+		shutdown_event = pqi_get_flush_cache_shutdown_event(pci_dev);
+		pqi_flush_cache(ctrl_info, shutdown_event);
+	}
 
-	pci_save_state(pci_dev);
-	pci_set_power_state(pci_dev, pci_choose_state(pci_dev, state));
+	pqi_stop_heartbeat_timer(ctrl_info);
+	pqi_crash_if_pending_command(ctrl_info);
+	pqi_free_irqs(ctrl_info);
 
 	ctrl_info->controller_online = false;
 	ctrl_info->pqi_mode_enabled = false;
@@ -8625,44 +9204,89 @@
 	return 0;
 }
 
-static __maybe_unused int pqi_resume(struct pci_dev *pci_dev)
+static __maybe_unused int pqi_suspend(struct device *dev)
+{
+	return pqi_suspend_or_freeze(dev, true);
+}
+
+static int pqi_resume_or_restore(struct device *dev)
 {
 	int rc;
+	struct pci_dev *pci_dev;
 	struct pqi_ctrl_info *ctrl_info;
 
+	pci_dev = to_pci_dev(dev);
 	ctrl_info = pci_get_drvdata(pci_dev);
 
-	if (pci_dev->current_state != PCI_D0) {
-		ctrl_info->max_hw_queue_index = 0;
-		pqi_free_interrupts(ctrl_info);
-		pqi_change_irq_mode(ctrl_info, IRQ_MODE_INTX);
-		rc = request_irq(pci_irq_vector(pci_dev, 0), pqi_irq_handler,
-			IRQF_SHARED, DRIVER_NAME_SHORT,
-			&ctrl_info->queue_groups[0]);
-		if (rc) {
-			dev_err(&ctrl_info->pci_dev->dev,
-				"irq %u init failed with error %d\n",
-				pci_dev->irq, rc);
-			return rc;
-		}
-		pqi_ctrl_unblock_device_reset(ctrl_info);
-		pqi_ctrl_unblock_requests(ctrl_info);
-		pqi_scsi_unblock_requests(ctrl_info);
-		pqi_ctrl_unblock_scan(ctrl_info);
-		return 0;
-	}
-
-	pci_set_power_state(pci_dev, PCI_D0);
-	pci_restore_state(pci_dev);
+	rc = pqi_request_irqs(ctrl_info);
+	if (rc)
+		return rc;
 
 	pqi_ctrl_unblock_device_reset(ctrl_info);
 	pqi_ctrl_unblock_requests(ctrl_info);
 	pqi_scsi_unblock_requests(ctrl_info);
 	pqi_ctrl_unblock_scan(ctrl_info);
 
+	ssleep(PQI_POST_RESET_DELAY_SECS);
+
 	return pqi_ctrl_init_resume(ctrl_info);
 }
 
+static int pqi_freeze(struct device *dev)
+{
+	return pqi_suspend_or_freeze(dev, false);
+}
+
+static int pqi_thaw(struct device *dev)
+{
+	int rc;
+	struct pci_dev *pci_dev;
+	struct pqi_ctrl_info *ctrl_info;
+
+	pci_dev = to_pci_dev(dev);
+	ctrl_info = pci_get_drvdata(pci_dev);
+
+	rc = pqi_request_irqs(ctrl_info);
+	if (rc)
+		return rc;
+
+	ctrl_info->controller_online = true;
+	ctrl_info->pqi_mode_enabled = true;
+
+	pqi_ctrl_unblock_device_reset(ctrl_info);
+	pqi_ctrl_unblock_requests(ctrl_info);
+	pqi_scsi_unblock_requests(ctrl_info);
+	pqi_ctrl_unblock_scan(ctrl_info);
+
+	return 0;
+}
+
+static int pqi_poweroff(struct device *dev)
+{
+	struct pci_dev *pci_dev;
+	struct pqi_ctrl_info *ctrl_info;
+	enum bmic_flush_cache_shutdown_event shutdown_event;
+
+	pci_dev = to_pci_dev(dev);
+	ctrl_info = pci_get_drvdata(pci_dev);
+
+	shutdown_event = pqi_get_flush_cache_shutdown_event(pci_dev);
+	pqi_flush_cache(ctrl_info, shutdown_event);
+
+	return 0;
+}
+
+static const struct dev_pm_ops pqi_pm_ops = {
+	.suspend = pqi_suspend,
+	.resume = pqi_resume_or_restore,
+	.freeze = pqi_freeze,
+	.thaw = pqi_thaw,
+	.poweroff = pqi_poweroff,
+	.restore = pqi_resume_or_restore,
+};
+
+#endif /* CONFIG_PM */
+
 /* Define the PCI IDs for the controllers that we support. */
 static const struct pci_device_id pqi_pci_id_table[] = {
 	{
@@ -8695,10 +9319,6 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
-			       0x193d, 0x8460)
-	},
-	{
-		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       0x193d, 0x1104)
 	},
 	{
@@ -8723,6 +9343,10 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x193d, 0x110b)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       0x193d, 0x8460)
 	},
 	{
@@ -8795,6 +9419,50 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x006b)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x006c)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x006d)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x006f)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0070)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0071)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0072)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0086)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0087)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0088)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1bd4, 0x0089)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       0x19e5, 0xd227)
 	},
 	{
@@ -8827,6 +9495,10 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x0659)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_VENDOR_ID_ADAPTEC2, 0x0800)
 	},
 	{
@@ -8951,6 +9623,10 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x1304)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_VENDOR_ID_ADAPTEC2, 0x1380)
 	},
 	{
@@ -9011,6 +9687,10 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x1463)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_VENDOR_ID_ADAPTEC2, 0x1470)
 	},
 	{
@@ -9023,6 +9703,18 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x1473)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x1474)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x1475)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_VENDOR_ID_ADAPTEC2, 0x1480)
 	},
 	{
@@ -9043,6 +9735,22 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14a2)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14a4)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14a5)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14a6)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_VENDOR_ID_ADAPTEC2, 0x14b0)
 	},
 	{
@@ -9059,6 +9767,18 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14c2)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14c3)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_ADAPTEC2, 0x14c4)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_VENDOR_ID_ADAPTEC2, 0x14d0)
 	},
 	{
@@ -9163,6 +9883,22 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1590, 0x036f)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1590, 0x0381)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1590, 0x0382)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1590, 0x0383)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       0x1d8d, 0x0800)
 	},
 	{
@@ -9187,6 +9923,10 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1f0c, 0x3161)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       0x1cf2, 0x5445)
 	},
 	{
@@ -9199,6 +9939,30 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cf2, 0x5449)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cf2, 0x544a)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cf2, 0x544b)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cf2, 0x544d)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cf2, 0x544e)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cf2, 0x544f)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       0x1cf2, 0x0b27)
 	},
 	{
@@ -9211,6 +9975,58 @@
 	},
 	{
 		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cc4, 0x0101)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       0x1cc4, 0x0201)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0220)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0221)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0520)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0522)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0620)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0621)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0622)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+			       PCI_VENDOR_ID_LENOVO, 0x0623)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+				0x1e93, 0x1000)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+				0x1e93, 0x1001)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
+				0x1e93, 0x1002)
+	},
+	{
+		PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x028f,
 			       PCI_ANY_ID, PCI_ANY_ID)
 	},
 	{ 0 }
@@ -9225,8 +10041,9 @@
 	.remove = pqi_pci_remove,
 	.shutdown = pqi_shutdown,
 #if defined(CONFIG_PM)
-	.suspend = pqi_suspend,
-	.resume = pqi_resume,
+	.driver = {
+		.pm = &pqi_pm_ops
+	},
 #endif
 };
 
@@ -9235,6 +10052,8 @@
 	int rc;
 
 	pr_info(DRIVER_NAME "\n");
+	pqi_verify_structures();
+	sis_verify_structures();
 
 	pqi_sas_transport_template = sas_attach_transport(&pqi_sas_transport_functions);
 	if (!pqi_sas_transport_template)
@@ -9258,7 +10077,7 @@
 module_init(pqi_init);
 module_exit(pqi_cleanup);
 
-static void __attribute__((unused)) verify_structures(void)
+static void pqi_verify_structures(void)
 {
 	BUILD_BUG_ON(offsetof(struct pqi_ctrl_registers,
 		sis_host_to_ctrl_doorbell) != 0x20);
@@ -9275,6 +10094,8 @@
 	BUILD_BUG_ON(offsetof(struct pqi_ctrl_registers,
 		sis_firmware_status) != 0xbc);
 	BUILD_BUG_ON(offsetof(struct pqi_ctrl_registers,
+		sis_ctrl_shutdown_reason_code) != 0xcc);
+	BUILD_BUG_ON(offsetof(struct pqi_ctrl_registers,
 		sis_mailbox) != 0x1000);
 	BUILD_BUG_ON(offsetof(struct pqi_ctrl_registers,
 		pqi_registers) != 0x4000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/smartpqi/smartpqi_sas_transport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/smartpqi/smartpqi_sas_transport.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
  *    driver for Microchip PQI-based storage controllers
- *    Copyright (c) 2019-2021 Microchip Technology Inc. and its subsidiaries
+ *    Copyright (c) 2019-2022 Microchip Technology Inc. and its subsidiaries
  *    Copyright (c) 2016-2018 Microsemi Corporation
  *    Copyright (c) 2016 PMC-Sierra, Inc.
  *
@@ -343,7 +343,7 @@
 	}
 
 	if (found_device->devtype == TYPE_ENCLOSURE) {
-		*identifier = get_unaligned_be64(&found_device->wwid);
+		*identifier = get_unaligned_be64(&found_device->wwid[8]);
 		rc = 0;
 		goto out;
 	}
@@ -364,7 +364,7 @@
 			memcmp(device->phys_connector,
 				found_device->phys_connector, 2) == 0) {
 			*identifier =
-				get_unaligned_be64(&device->wwid);
+				get_unaligned_be64(&device->wwid[8]);
 			rc = 0;
 			goto out;
 		}
@@ -380,7 +380,7 @@
 		if (device->devtype == TYPE_ENCLOSURE &&
 			CISS_GET_DRIVE_NUMBER(device->scsi3addr) ==
 				PQI_VSEP_CISS_BTL) {
-			*identifier = get_unaligned_be64(&device->wwid);
+			*identifier = get_unaligned_be64(&device->wwid[8]);
 			rc = 0;
 			goto out;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/smartpqi/smartpqi_sis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/smartpqi/smartpqi_sis.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
  *    driver for Microchip PQI-based storage controllers
- *    Copyright (c) 2019-2021 Microchip Technology Inc. and its subsidiaries
+ *    Copyright (c) 2019-2022 Microchip Technology Inc. and its subsidiaries
  *    Copyright (c) 2016-2018 Microsemi Corporation
  *    Copyright (c) 2016 PMC-Sierra, Inc.
  *
@@ -51,12 +51,20 @@
 #define SIS_BASE_STRUCT_REVISION		9
 #define SIS_BASE_STRUCT_ALIGNMENT		16
 
+#define SIS_CTRL_KERNEL_FW_TRIAGE		0x3
 #define SIS_CTRL_KERNEL_UP			0x80
 #define SIS_CTRL_KERNEL_PANIC			0x100
 #define SIS_CTRL_READY_TIMEOUT_SECS		180
 #define SIS_CTRL_READY_RESUME_TIMEOUT_SECS	90
 #define SIS_CTRL_READY_POLL_INTERVAL_MSECS	10
 
+enum sis_fw_triage_status {
+	FW_TRIAGE_NOT_STARTED = 0,
+	FW_TRIAGE_STARTED,
+	FW_TRIAGE_COND_INVALID,
+	FW_TRIAGE_COMPLETED
+};
+
 #pragma pack(1)
 
 /* for use with SIS_CMD_INIT_BASE_STRUCT_ADDRESS command */
@@ -78,13 +86,15 @@
 
 #pragma pack()
 
+unsigned int sis_ctrl_ready_timeout_secs = SIS_CTRL_READY_TIMEOUT_SECS;
+
 static int sis_wait_for_ctrl_ready_with_timeout(struct pqi_ctrl_info *ctrl_info,
 	unsigned int timeout_secs)
 {
 	unsigned long timeout;
 	u32 status;
 
-	timeout = (timeout_secs * PQI_HZ) + jiffies;
+	timeout = (timeout_secs * HZ) + jiffies;
 
 	while (1) {
 		status = readl(&ctrl_info->registers->sis_firmware_status);
@@ -114,7 +124,7 @@
 int sis_wait_for_ctrl_ready(struct pqi_ctrl_info *ctrl_info)
 {
 	return sis_wait_for_ctrl_ready_with_timeout(ctrl_info,
-		SIS_CTRL_READY_TIMEOUT_SECS);
+		sis_ctrl_ready_timeout_secs);
 }
 
 int sis_wait_for_ctrl_ready_resume(struct pqi_ctrl_info *ctrl_info)
@@ -130,7 +140,7 @@
 
 	status = readl(&ctrl_info->registers->sis_firmware_status);
 
-	if (status & SIS_CTRL_KERNEL_PANIC)
+	if (status != ~0 && (status & SIS_CTRL_KERNEL_PANIC))
 		running = false;
 	else
 		running = true;
@@ -186,6 +196,7 @@
 
 	/* Disable doorbell interrupts by masking all interrupts. */
 	writel(~0, &registers->sis_interrupt_mask);
+	usleep_range(1000, 2000);
 
 	/*
 	 * Force the completion of the interrupt mask register write before
@@ -201,7 +212,7 @@
 	 * the top of the loop in order to give the controller time to start
 	 * processing the command before we start polling.
 	 */
-	timeout = (SIS_CMD_COMPLETE_TIMEOUT_SECS * PQI_HZ) + jiffies;
+	timeout = (SIS_CMD_COMPLETE_TIMEOUT_SECS * HZ) + jiffies;
 	while (1) {
 		msleep(SIS_CMD_COMPLETE_POLL_INTERVAL_MSECS);
 		doorbell = readl(&registers->sis_ctrl_to_host_doorbell);
@@ -347,7 +358,7 @@
 	u32 doorbell_register;
 	unsigned long timeout;
 
-	timeout = (SIS_DOORBELL_BIT_CLEAR_TIMEOUT_SECS * PQI_HZ) + jiffies;
+	timeout = (SIS_DOORBELL_BIT_CLEAR_TIMEOUT_SECS * HZ) + jiffies;
 
 	while (1) {
 		doorbell_register =
@@ -375,6 +386,7 @@
 static inline int sis_set_doorbell_bit(struct pqi_ctrl_info *ctrl_info, u32 bit)
 {
 	writel(bit, &ctrl_info->registers->sis_host_to_ctrl_doorbell);
+	usleep_range(1000, 2000);
 
 	return sis_wait_for_doorbell_bit_to_clear(ctrl_info, bit);
 }
@@ -389,14 +401,17 @@
 	sis_set_doorbell_bit(ctrl_info, SIS_ENABLE_INTX);
 }
 
-void sis_shutdown_ctrl(struct pqi_ctrl_info *ctrl_info)
+void sis_shutdown_ctrl(struct pqi_ctrl_info *ctrl_info,
+	enum pqi_ctrl_shutdown_reason ctrl_shutdown_reason)
 {
 	if (readl(&ctrl_info->registers->sis_firmware_status) &
 		SIS_CTRL_KERNEL_PANIC)
 		return;
 
-	writel(SIS_TRIGGER_SHUTDOWN,
-		&ctrl_info->registers->sis_host_to_ctrl_doorbell);
+	if (ctrl_info->firmware_triage_supported)
+		writel(ctrl_shutdown_reason, &ctrl_info->registers->sis_ctrl_shutdown_reason_code);
+
+	writel(SIS_TRIGGER_SHUTDOWN, &ctrl_info->registers->sis_host_to_ctrl_doorbell);
 }
 
 int sis_pqi_reset_quiesce(struct pqi_ctrl_info *ctrl_info)
@@ -412,6 +427,7 @@
 void sis_write_driver_scratch(struct pqi_ctrl_info *ctrl_info, u32 value)
 {
 	writel(value, &ctrl_info->registers->sis_driver_scratch);
+	usleep_range(1000, 2000);
 }
 
 u32 sis_read_driver_scratch(struct pqi_ctrl_info *ctrl_info)
@@ -419,13 +435,56 @@
 	return readl(&ctrl_info->registers->sis_driver_scratch);
 }
 
+static inline enum sis_fw_triage_status
+	sis_read_firmware_triage_status(struct pqi_ctrl_info *ctrl_info)
+{
+	return ((enum sis_fw_triage_status)(readl(&ctrl_info->registers->sis_firmware_status) &
+		SIS_CTRL_KERNEL_FW_TRIAGE));
+}
+
 void sis_soft_reset(struct pqi_ctrl_info *ctrl_info)
 {
 	writel(SIS_SOFT_RESET,
 		&ctrl_info->registers->sis_host_to_ctrl_doorbell);
 }
 
-static void __attribute__((unused)) verify_structures(void)
+#define SIS_FW_TRIAGE_STATUS_TIMEOUT_SECS		300
+#define SIS_FW_TRIAGE_STATUS_POLL_INTERVAL_SECS		1
+
+int sis_wait_for_fw_triage_completion(struct pqi_ctrl_info *ctrl_info)
+{
+	int rc;
+	enum sis_fw_triage_status status;
+	unsigned long timeout;
+
+	timeout = (SIS_FW_TRIAGE_STATUS_TIMEOUT_SECS * HZ) + jiffies;
+	while (1) {
+		status = sis_read_firmware_triage_status(ctrl_info);
+		if (status == FW_TRIAGE_COND_INVALID) {
+			dev_err(&ctrl_info->pci_dev->dev,
+				"firmware triage condition invalid\n");
+			rc = -EINVAL;
+			break;
+		} else if (status == FW_TRIAGE_NOT_STARTED ||
+			status == FW_TRIAGE_COMPLETED) {
+			rc = 0;
+			break;
+		}
+
+		if (time_after(jiffies, timeout)) {
+			dev_err(&ctrl_info->pci_dev->dev,
+				"timed out waiting for firmware triage status\n");
+			rc = -ETIMEDOUT;
+			break;
+		}
+
+		ssleep(SIS_FW_TRIAGE_STATUS_POLL_INTERVAL_SECS);
+	}
+
+	return rc;
+}
+
+void sis_verify_structures(void)
 {
 	BUILD_BUG_ON(offsetof(struct sis_base_struct,
 		revision) != 0x0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/smartpqi/smartpqi_sis.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/smartpqi/smartpqi_sis.h
@@ -1,7 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
  *    driver for Microchip PQI-based storage controllers
- *    Copyright (c) 2019-2021 Microchip Technology Inc. and its subsidiaries
+ *    Copyright (c) 2019-2022 Microchip Technology Inc. and its subsidiaries
  *    Copyright (c) 2016-2018 Microsemi Corporation
  *    Copyright (c) 2016 PMC-Sierra, Inc.
  *
@@ -12,6 +12,7 @@
 #if !defined(_SMARTPQI_SIS_H)
 #define _SMARTPQI_SIS_H
 
+void sis_verify_structures(void);
 int sis_wait_for_ctrl_ready(struct pqi_ctrl_info *ctrl_info);
 int sis_wait_for_ctrl_ready_resume(struct pqi_ctrl_info *ctrl_info);
 bool sis_is_firmware_running(struct pqi_ctrl_info *ctrl_info);
@@ -21,12 +22,16 @@
 int sis_init_base_struct_addr(struct pqi_ctrl_info *ctrl_info);
 void sis_enable_msix(struct pqi_ctrl_info *ctrl_info);
 void sis_enable_intx(struct pqi_ctrl_info *ctrl_info);
-void sis_shutdown_ctrl(struct pqi_ctrl_info *ctrl_info);
+void sis_shutdown_ctrl(struct pqi_ctrl_info *ctrl_info,
+	enum pqi_ctrl_shutdown_reason ctrl_shutdown_reason);
 int sis_pqi_reset_quiesce(struct pqi_ctrl_info *ctrl_info);
 int sis_reenable_sis_mode(struct pqi_ctrl_info *ctrl_info);
 void sis_write_driver_scratch(struct pqi_ctrl_info *ctrl_info, u32 value);
 u32 sis_read_driver_scratch(struct pqi_ctrl_info *ctrl_info);
 void sis_soft_reset(struct pqi_ctrl_info *ctrl_info);
 u32 sis_get_product_id(struct pqi_ctrl_info *ctrl_info);
+int sis_wait_for_fw_triage_completion(struct pqi_ctrl_info *ctrl_info);
+
+extern unsigned int sis_ctrl_ready_timeout_secs;
 
 #endif	/* _SMARTPQI_SIS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/snic/snic_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/snic/snic_debugfs.c
@@ -451,6 +451,6 @@
 void
 snic_trc_debugfs_term(void)
 {
-	debugfs_remove(debugfs_lookup(TRC_FILE, snic_glob->trc_root));
-	debugfs_remove(debugfs_lookup(TRC_ENABLE_FILE, snic_glob->trc_root));
+	debugfs_lookup_and_remove(TRC_FILE, snic_glob->trc_root);
+	debugfs_lookup_and_remove(TRC_ENABLE_FILE, snic_glob->trc_root);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/snic/snic_disc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/snic/snic_disc.c
@@ -318,7 +318,10 @@
 			      ret);
 
 		put_device(&snic->shost->shost_gendev);
-		kfree(tgt);
+		spin_lock_irqsave(snic->shost->host_lock, flags);
+		list_del(&tgt->list);
+		spin_unlock_irqrestore(snic->shost->host_lock, flags);
+		put_device(&tgt->dev);
 		tgt = NULL;
 
 		return tgt;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sr.c
@@ -44,6 +44,7 @@
 #include <linux/cdrom.h>
 #include <linux/interrupt.h>
 #include <linux/init.h>
+#include <linux/major.h>
 #include <linux/blkdev.h>
 #include <linux/blk-pm.h>
 #include <linux/mutex.h>
@@ -578,7 +579,7 @@
 
 	scsi_autopm_get_device(sdev);
 
-	if (ret != CDROMCLOSETRAY && ret != CDROMEJECT) {
+	if (cmd != CDROMCLOSETRAY && cmd != CDROMEJECT) {
 		ret = cdrom_ioctl(&cd->cdi, bdev, mode, cmd, arg);
 		if (ret != -ENOSYS)
 			goto put;
@@ -683,9 +684,10 @@
 	disk->minors = 1;
 	sprintf(disk->disk_name, "sr%d", minor);
 	disk->fops = &sr_bdops;
-	disk->flags = GENHD_FL_CD | GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE;
+	disk->flags = GENHD_FL_CD;
 	disk->events = DISK_EVENT_MEDIA_CHANGE | DISK_EVENT_EJECT_REQUEST;
-	disk->event_flags = DISK_EVENT_FLAG_POLL | DISK_EVENT_FLAG_UEVENT;
+	disk->event_flags = DISK_EVENT_FLAG_POLL | DISK_EVENT_FLAG_UEVENT |
+				DISK_EVENT_FLAG_BLOCK_ON_EXCL_WRITE;
 
 	blk_queue_rq_timeout(sdev->request_queue, SR_TIMEOUT);
 
@@ -851,7 +853,7 @@
 
 
 	/* allocate transfer buffer */
-	buffer = kmalloc(512, GFP_KERNEL | GFP_DMA);
+	buffer = kmalloc(512, GFP_KERNEL);
 	if (!buffer) {
 		sr_printk(KERN_ERR, cd, "out of memory.\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sr_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sr_ioctl.c
@@ -41,7 +41,7 @@
 	int result;
 	unsigned char *buffer;
 
-	buffer = kmalloc(32, GFP_KERNEL);
+	buffer = kzalloc(32, GFP_KERNEL);
 	if (!buffer)
 		return -ENOMEM;
 
@@ -55,10 +55,13 @@
 	cgc.data_direction = DMA_FROM_DEVICE;
 
 	result = sr_do_ioctl(cd, &cgc);
+	if (result)
+		goto err;
 
 	tochdr->cdth_trk0 = buffer[2];
 	tochdr->cdth_trk1 = buffer[3];
 
+err:
 	kfree(buffer);
 	return result;
 }
@@ -71,7 +74,7 @@
 	int result;
 	unsigned char *buffer;
 
-	buffer = kmalloc(32, GFP_KERNEL);
+	buffer = kzalloc(32, GFP_KERNEL);
 	if (!buffer)
 		return -ENOMEM;
 
@@ -86,6 +89,8 @@
 	cgc.data_direction = DMA_FROM_DEVICE;
 
 	result = sr_do_ioctl(cd, &cgc);
+	if (result)
+		goto err;
 
 	tocentry->cdte_ctrl = buffer[5] & 0xf;
 	tocentry->cdte_adr = buffer[5] >> 4;
@@ -98,6 +103,7 @@
 		tocentry->cdte_addr.lba = (((((buffer[8] << 8) + buffer[9]) << 8)
 			+ buffer[10]) << 8) + buffer[11];
 
+err:
 	kfree(buffer);
 	return result;
 }
@@ -384,7 +390,7 @@
 {
 	Scsi_CD *cd = cdi->handle;
 	struct packet_command cgc;
-	char *buffer = kmalloc(32, GFP_KERNEL);
+	char *buffer = kzalloc(32, GFP_KERNEL);
 	int result;
 
 	if (!buffer)
@@ -400,10 +406,13 @@
 	cgc.data_direction = DMA_FROM_DEVICE;
 	cgc.timeout = IOCTL_TIMEOUT;
 	result = sr_do_ioctl(cd, &cgc);
+	if (result)
+		goto err;
 
 	memcpy(mcn->medium_catalog_number, buffer + 9, 13);
 	mcn->medium_catalog_number[13] = 0;
 
+err:
 	kfree(buffer);
 	return result;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sr_vendor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sr_vendor.c
@@ -131,7 +131,7 @@
 	if (cd->vendor == VENDOR_TOSHIBA)
 		density = (blocklength > 2048) ? 0x81 : 0x83;
 
-	buffer = kmalloc(512, GFP_KERNEL | GFP_DMA);
+	buffer = kmalloc(512, GFP_KERNEL);
 	if (!buffer)
 		return -ENOMEM;
 
@@ -179,7 +179,7 @@
 	if (cd->cdi.mask & CDC_MULTI_SESSION)
 		return 0;
 
-	buffer = kmalloc(512, GFP_KERNEL | GFP_DMA);
+	buffer = kmalloc(512, GFP_KERNEL);
 	if (!buffer)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/st.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/st.c
@@ -32,6 +32,7 @@
 #include <linux/slab.h>
 #include <linux/errno.h>
 #include <linux/mtio.h>
+#include <linux/major.h>
 #include <linux/cdrom.h>
 #include <linux/ioctl.h>
 #include <linux/fcntl.h>
@@ -3500,6 +3501,7 @@
 	int i, cmd_nr, cmd_type, bt;
 	int retval = 0;
 	unsigned int blk;
+	bool cmd_mtiocget;
 	struct scsi_tape *STp = file->private_data;
 	struct st_modedef *STm;
 	struct st_partstat *STps;
@@ -3613,6 +3615,7 @@
 			 */
 			if (mtc.mt_op != MTREW &&
 			    mtc.mt_op != MTOFFL &&
+			    mtc.mt_op != MTLOAD &&
 			    mtc.mt_op != MTRETEN &&
 			    mtc.mt_op != MTERASE &&
 			    mtc.mt_op != MTSEEK &&
@@ -3726,17 +3729,28 @@
 		goto out;
 	}
 
+	cmd_mtiocget = cmd_type == _IOC_TYPE(MTIOCGET) && cmd_nr == _IOC_NR(MTIOCGET);
+
 	if ((i = flush_buffer(STp, 0)) < 0) {
-		retval = i;
-		goto out;
-	}
-	if (STp->can_partitions &&
-	    (i = switch_partition(STp)) < 0) {
-		retval = i;
-		goto out;
+		if (cmd_mtiocget && STp->pos_unknown) {
+			/* flush fails -> modify status accordingly */
+			reset_state(STp);
+			STp->pos_unknown = 1;
+		} else { /* return error */
+			retval = i;
+			goto out;
+		}
+	} else { /* flush_buffer succeeds */
+		if (STp->can_partitions) {
+			i = switch_partition(STp);
+			if (i < 0) {
+				retval = i;
+				goto out;
+			}
+		}
 	}
 
-	if (cmd_type == _IOC_TYPE(MTIOCGET) && cmd_nr == _IOC_NR(MTIOCGET)) {
+	if (cmd_mtiocget) {
 		struct mtget mt_status;
 
 		if (_IOC_SIZE(cmd_in) != sizeof(struct mtget)) {
@@ -3750,7 +3764,7 @@
 		    ((STp->density << MT_ST_DENSITY_SHIFT) & MT_ST_DENSITY_MASK);
 		mt_status.mt_blkno = STps->drv_block;
 		mt_status.mt_fileno = STps->drv_file;
-		if (STp->block_size != 0) {
+		if (STp->block_size != 0 && mt_status.mt_blkno >= 0) {
 			if (STps->rw == ST_WRITING)
 				mt_status.mt_blkno +=
 				    (STp->buffer)->buffer_bytes / STp->block_size;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/stex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/stex.c
@@ -109,7 +109,9 @@
 	TASK_ATTRIBUTE_HEADOFQUEUE		= 0x1,
 	TASK_ATTRIBUTE_ORDERED			= 0x2,
 	TASK_ATTRIBUTE_ACA			= 0x4,
+};
 
+enum {
 	SS_STS_NORMAL				= 0x80000000,
 	SS_STS_DONE				= 0x40000000,
 	SS_STS_HANDSHAKE			= 0x20000000,
@@ -121,7 +123,9 @@
 	SS_I2H_REQUEST_RESET			= 0x2000,
 
 	SS_MU_OPERATIONAL			= 0x80000000,
+};
 
+enum {
 	STEX_CDB_LENGTH				= 16,
 	STATUS_VAR_LEN				= 128,
 
@@ -665,16 +669,17 @@
 		return 0;
 	case PASSTHRU_CMD:
 		if (cmd->cmnd[1] == PASSTHRU_GET_DRVVER) {
-			struct st_drvver ver;
+			const struct st_drvver ver = {
+				.major = ST_VER_MAJOR,
+				.minor = ST_VER_MINOR,
+				.oem = ST_OEM,
+				.build = ST_BUILD_VER,
+				.signature[0] = PASSTHRU_SIGNATURE,
+				.console_id = host->max_id - 1,
+				.host_no = hba->host->host_no,
+			};
 			size_t cp_len = sizeof(ver);
 
-			ver.major = ST_VER_MAJOR;
-			ver.minor = ST_VER_MINOR;
-			ver.oem = ST_OEM;
-			ver.build = ST_BUILD_VER;
-			ver.signature[0] = PASSTHRU_SIGNATURE;
-			ver.console_id = host->max_id - 1;
-			ver.host_no = hba->host->host_no;
 			cp_len = scsi_sg_copy_from_buffer(cmd, &ver, cp_len);
 			if (sizeof(ver) == cp_len)
 				cmd->result = DID_OK << 16;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/storvsc_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/storvsc_drv.c
@@ -155,6 +155,8 @@
 */
 static int vmstor_proto_version;
 
+static bool hv_dev_is_fc(struct hv_device *hv_dev);
+
 #define STORVSC_LOGGING_NONE	0
 #define STORVSC_LOGGING_ERROR	1
 #define STORVSC_LOGGING_WARN	2
@@ -187,6 +189,12 @@
 	u32 queue_sort_ey;
 } __packed;
 
+#define storvsc_log_ratelimited(dev, level, fmt, ...)				\
+do {										\
+	if (do_logging(level))							\
+		dev_warn_ratelimited(&(dev)->device, fmt, ##__VA_ARGS__);	\
+} while (0)
+
 struct vmscsi_request {
 	u16 length;
 	u8 srb_status;
@@ -344,16 +352,21 @@
 };
 
 /*
- * SRB status codes and masks; a subset of the codes used here.
+ * SRB status codes and masks. In the 8-bit field, the two high order bits
+ * are flags, while the remaining 6 bits are an integer status code.  The
+ * definitions here include only the subset of the integer status codes that
+ * are tested for in this driver.
  */
-
 #define SRB_STATUS_AUTOSENSE_VALID	0x80
 #define SRB_STATUS_QUEUE_FROZEN		0x40
-#define SRB_STATUS_INVALID_LUN	0x20
-#define SRB_STATUS_SUCCESS	0x01
-#define SRB_STATUS_ABORTED	0x02
-#define SRB_STATUS_ERROR	0x04
-#define SRB_STATUS_DATA_OVERRUN	0x12
+
+/* SRB status integer codes */
+#define SRB_STATUS_SUCCESS		0x01
+#define SRB_STATUS_ABORTED		0x02
+#define SRB_STATUS_ERROR		0x04
+#define SRB_STATUS_INVALID_REQUEST	0x06
+#define SRB_STATUS_DATA_OVERRUN		0x12
+#define SRB_STATUS_INVALID_LUN		0x20
 
 #define SRB_STATUS(status) \
 	(status & ~(SRB_STATUS_AUTOSENSE_VALID | SRB_STATUS_QUEUE_FROZEN))
@@ -362,6 +375,7 @@
  */
 
 static int storvsc_ringbuffer_size = (128 * 1024);
+static int aligned_ringbuffer_size;
 static u32 max_outstanding_req_per_channel;
 static int storvsc_change_queue_depth(struct scsi_device *sdev, int queue_depth);
 
@@ -401,6 +415,7 @@
 #define STORVSC_FC_MAX_LUNS_PER_TARGET			255
 #define STORVSC_FC_MAX_TARGETS				128
 #define STORVSC_FC_MAX_CHANNELS				8
+#define STORVSC_FC_MAX_XFER_SIZE			((u32)(512 * 1024))
 
 #define STORVSC_IDE_MAX_LUNS_PER_TARGET			64
 #define STORVSC_IDE_MAX_TARGETS				1
@@ -731,8 +746,8 @@
 	new_sc->next_request_id_callback = storvsc_next_request_id;
 
 	ret = vmbus_open(new_sc,
-			 storvsc_ringbuffer_size,
-			 storvsc_ringbuffer_size,
+			 aligned_ringbuffer_size,
+			 aligned_ringbuffer_size,
 			 (void *)&props,
 			 sizeof(struct vmstorage_channel_properties),
 			 storvsc_on_channel_callback, new_sc);
@@ -1032,38 +1047,41 @@
 	void (*process_err_fn)(struct work_struct *work);
 	struct hv_host_device *host_dev = shost_priv(host);
 
-	/*
-	 * In some situations, Hyper-V sets multiple bits in the
-	 * srb_status, such as ABORTED and ERROR. So process them
-	 * individually, with the most specific bits first.
-	 */
-
-	if (vm_srb->srb_status & SRB_STATUS_INVALID_LUN) {
-		set_host_byte(scmnd, DID_NO_CONNECT);
-		process_err_fn = storvsc_remove_lun;
-		goto do_work;
-	}
+	switch (SRB_STATUS(vm_srb->srb_status)) {
+	case SRB_STATUS_ERROR:
+	case SRB_STATUS_ABORTED:
+	case SRB_STATUS_INVALID_REQUEST:
+		if (vm_srb->srb_status & SRB_STATUS_AUTOSENSE_VALID) {
+			/* Check for capacity change */
+			if ((asc == 0x2a) && (ascq == 0x9)) {
+				process_err_fn = storvsc_device_scan;
+				/* Retry the I/O that triggered this. */
+				set_host_byte(scmnd, DID_REQUEUE);
+				goto do_work;
+			}
 
-	if (vm_srb->srb_status & SRB_STATUS_ABORTED) {
-		if (vm_srb->srb_status & SRB_STATUS_AUTOSENSE_VALID &&
-		    /* Capacity data has changed */
-		    (asc == 0x2a) && (ascq == 0x9)) {
-			process_err_fn = storvsc_device_scan;
 			/*
-			 * Retry the I/O that triggered this.
+			 * Check for "Operating parameters have changed"
+			 * due to Hyper-V changing the VHD/VHDX BlockSize
+			 * when adding/removing a differencing disk. This
+			 * causes discard_granularity to change, so do a
+			 * rescan to pick up the new granularity. We don't
+			 * want scsi_report_sense() to output a message
+			 * that a sysadmin wouldn't know what to do with.
 			 */
-			set_host_byte(scmnd, DID_REQUEUE);
-			goto do_work;
-		}
-	}
+			if ((asc == 0x3f) && (ascq != 0x03) &&
+					(ascq != 0x0e)) {
+				process_err_fn = storvsc_device_scan;
+				set_host_byte(scmnd, DID_REQUEUE);
+				goto do_work;
+			}
 
-	if (vm_srb->srb_status & SRB_STATUS_ERROR) {
-		/*
-		 * Let upper layer deal with error when
-		 * sense message is present.
-		 */
-		if (vm_srb->srb_status & SRB_STATUS_AUTOSENSE_VALID)
+			/*
+			 * Otherwise, let upper layer deal with the
+			 * error when sense message is present
+			 */
 			return;
+		}
 
 		/*
 		 * If there is an error; offline the device since all
@@ -1086,6 +1104,13 @@
 		default:
 			set_host_byte(scmnd, DID_ERROR);
 		}
+		return;
+
+	case SRB_STATUS_INVALID_LUN:
+		set_host_byte(scmnd, DID_NO_CONNECT);
+		process_err_fn = storvsc_remove_lun;
+		goto do_work;
+
 	}
 	return;
 
@@ -1175,6 +1200,7 @@
 	 * not correctly handle:
 	 * INQUIRY command with page code parameter set to 0x80
 	 * MODE_SENSE command with cmd[2] == 0x1c
+	 * MAINTENANCE_IN is not supported by HyperV FC passthrough
 	 *
 	 * Setup srb and scsi status so this won't be fatal.
 	 * We do this so we can distinguish truly fatal failues
@@ -1182,7 +1208,9 @@
 	 */
 
 	if ((stor_pkt->vm_srb.cdb[0] == INQUIRY) ||
-	   (stor_pkt->vm_srb.cdb[0] == MODE_SENSE)) {
+	   (stor_pkt->vm_srb.cdb[0] == MODE_SENSE) ||
+	   (stor_pkt->vm_srb.cdb[0] == MAINTENANCE_IN &&
+	   hv_dev_is_fc(device))) {
 		vstor_packet->vm_srb.scsi_status = 0;
 		vstor_packet->vm_srb.srb_status = SRB_STATUS_SUCCESS;
 	}
@@ -1209,7 +1237,7 @@
 		int loglevel = (stor_pkt->vm_srb.cdb[0] == TEST_UNIT_READY) ?
 			STORVSC_LOGGING_WARN : STORVSC_LOGGING_ERROR;
 
-		storvsc_log(device, loglevel,
+		storvsc_log_ratelimited(device, loglevel,
 			"tag#%d cmd 0x%x status: scsi 0x%x srb 0x%x hv 0x%x\n",
 			scsi_cmd_to_rq(request->cmd)->tag,
 			stor_pkt->vm_srb.cdb[0],
@@ -1611,6 +1639,8 @@
 {
 	blk_queue_rq_timeout(sdevice->request_queue, (storvsc_timeout * HZ));
 
+	/* storvsc devices don't support MAINTENANCE_IN SCSI cmd */
+	sdevice->no_report_opcodes = 1;
 	sdevice->no_write_same = 1;
 
 	/*
@@ -1714,10 +1744,6 @@
  */
 static enum blk_eh_timer_return storvsc_eh_timed_out(struct scsi_cmnd *scmnd)
 {
-#if IS_ENABLED(CONFIG_SCSI_FC_ATTRS)
-	if (scmnd->device->host->transportt == fc_transport_template)
-		return fc_eh_timed_out(scmnd);
-#endif
 	return BLK_EH_RESET_TIMER;
 }
 
@@ -1828,7 +1854,8 @@
 
 	length = scsi_bufflen(scmnd);
 	payload = (struct vmbus_packet_mpb_array *)&cmd_request->mpb;
-	payload_sz = sizeof(cmd_request->mpb);
+	payload->range.len = 0;
+	payload_sz = 0;
 
 	if (sg_count) {
 		unsigned int hvpgoff, hvpfns_to_add;
@@ -1836,10 +1863,10 @@
 		unsigned int hvpg_count = HVPFN_UP(offset_in_hvpg + length);
 		u64 hvpfn;
 
-		if (hvpg_count > MAX_PAGE_BUFFER_COUNT) {
+		payload_sz = (hvpg_count * sizeof(u64) +
+			      sizeof(struct vmbus_packet_mpb_array));
 
-			payload_sz = (hvpg_count * sizeof(u64) +
-				      sizeof(struct vmbus_packet_mpb_array));
+		if (hvpg_count > MAX_PAGE_BUFFER_COUNT) {
 			payload = kzalloc(payload_sz, GFP_ATOMIC);
 			if (!payload)
 				return SCSI_MLQUEUE_DEVICE_BUSY;
@@ -1907,7 +1934,7 @@
 	.cmd_per_lun =		2048,
 	.this_id =		-1,
 	/* Ensure there are no gaps in presented sgls */
-	.virt_boundary_mask =	PAGE_SIZE-1,
+	.virt_boundary_mask =	HV_HYP_PAGE_SIZE - 1,
 	.no_write_same =	1,
 	.track_queue_depth =	1,
 	.change_queue_depth =	storvsc_change_queue_depth,
@@ -1961,6 +1988,7 @@
 	int max_targets;
 	int max_channels;
 	int max_sub_channels = 0;
+	u32 max_xfer_bytes;
 
 	/*
 	 * Based on the windows host we are running on,
@@ -2018,7 +2046,7 @@
 	hv_set_drvdata(device, stor_device);
 
 	stor_device->port_number = host->host_no;
-	ret = storvsc_connect_to_vsp(device, storvsc_ringbuffer_size, is_fc);
+	ret = storvsc_connect_to_vsp(device, aligned_ringbuffer_size, is_fc);
 	if (ret)
 		goto err_out1;
 
@@ -2049,12 +2077,31 @@
 	}
 	/* max cmd length */
 	host->max_cmd_len = STORVSC_MAX_CMD_LEN;
-
 	/*
-	 * set the table size based on the info we got
-	 * from the host.
+	 * Any reasonable Hyper-V configuration should provide
+	 * max_transfer_bytes value aligning to HV_HYP_PAGE_SIZE,
+	 * protecting it from any weird value.
+	 */
+	max_xfer_bytes = round_down(stor_device->max_transfer_bytes, HV_HYP_PAGE_SIZE);
+	if (is_fc)
+		max_xfer_bytes = min(max_xfer_bytes, STORVSC_FC_MAX_XFER_SIZE);
+
+	/* max_hw_sectors_kb */
+	host->max_sectors = max_xfer_bytes >> 9;
+	/*
+	 * There are 2 requirements for Hyper-V storvsc sgl segments,
+	 * based on which the below calculation for max segments is
+	 * done:
+	 *
+	 * 1. Except for the first and last sgl segment, all sgl segments
+	 *    should be align to HV_HYP_PAGE_SIZE, that also means the
+	 *    maximum number of segments in a sgl can be calculated by
+	 *    dividing the total max transfer length by HV_HYP_PAGE_SIZE.
+	 *
+	 * 2. Except for the first and last, each entry in the SGL must
+	 *    have an offset that is a multiple of HV_HYP_PAGE_SIZE.
 	 */
-	host->sg_tablesize = (stor_device->max_transfer_bytes >> PAGE_SHIFT);
+	host->sg_tablesize = (max_xfer_bytes >> HV_HYP_PAGE_SHIFT) + 1;
 	/*
 	 * For non-IDE disks, the host supports multiple channels.
 	 * Set the number of HW queues we are supporting.
@@ -2076,7 +2123,7 @@
 	 */
 	host_dev->handle_error_wq =
 			alloc_ordered_workqueue("storvsc_error_wq_%d",
-						WQ_MEM_RECLAIM,
+						0,
 						host->host_no);
 	if (!host_dev->handle_error_wq) {
 		ret = -ENOMEM;
@@ -2192,7 +2239,7 @@
 {
 	int ret;
 
-	ret = storvsc_connect_to_vsp(hv_dev, storvsc_ringbuffer_size,
+	ret = storvsc_connect_to_vsp(hv_dev, aligned_ringbuffer_size,
 				     hv_dev_is_fc(hv_dev));
 	return ret;
 }
@@ -2230,8 +2277,9 @@
 	 * for Win7 and older hosts because it does not take into account
 	 * the vmscsi_size_delta correction to the max request size.
 	 */
+	aligned_ringbuffer_size = VMBUS_RING_SIZE(storvsc_ringbuffer_size);
 	max_outstanding_req_per_channel =
-		((storvsc_ringbuffer_size - PAGE_SIZE) /
+		((aligned_ringbuffer_size - PAGE_SIZE) /
 		ALIGN(MAX_MULTIPAGE_BUFFER_PACKET +
 		sizeof(struct vstor_packet) + sizeof(u64),
 		sizeof(u64)));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/sun3_scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/sun3_scsi.c
@@ -334,7 +334,7 @@
 static int sun3scsi_dma_xfer_len(struct NCR5380_hostdata *hostdata,
                                  struct scsi_cmnd *cmd)
 {
-	int wanted_len = cmd->SCp.this_residual;
+	int wanted_len = NCR5380_to_ncmd(cmd)->this_residual;
 
 	if (wanted_len < DMA_MIN_SIZE || blk_rq_is_passthrough(scsi_cmd_to_rq(cmd)))
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/cdns-pltfrm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/cdns-pltfrm.c
@@ -136,7 +136,7 @@
 	 * Make sure the register was updated,
 	 * UniPro layer will not work with an incorrect value.
 	 */
-	mb();
+	ufshcd_readl(hba, CDNS_UFS_REG_HCLKDIV);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/tc-dwc-g210-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/tc-dwc-g210-pci.c
@@ -110,7 +110,6 @@
 		return err;
 	}
 
-	pci_set_drvdata(pdev, hba);
 	pm_runtime_put_noidle(&pdev->dev);
 	pm_runtime_allow(&pdev->dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ti-j721e-ufs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ti-j721e-ufs.c
@@ -29,11 +29,9 @@
 		return PTR_ERR(regbase);
 
 	pm_runtime_enable(dev);
-	ret = pm_runtime_get_sync(dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(dev);
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret < 0)
 		goto disable_pm;
-	}
 
 	/* Select MPHY refclk frequency */
 	clk = devm_clk_get(dev, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufs-exynos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufs-exynos.c
@@ -1038,12 +1038,12 @@
 	hci_writel(ufs, 1 << 0, HCI_GPIO_OUT);
 }
 
-static void exynos_ufs_pre_hibern8(struct ufs_hba *hba, u8 enter)
+static void exynos_ufs_pre_hibern8(struct ufs_hba *hba, enum uic_cmd_dme cmd)
 {
 	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
 	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
 
-	if (!enter) {
+	if (cmd == UIC_CMD_DME_HIBER_EXIT) {
 		if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL)
 			exynos_ufs_disable_auto_ctrl_hcc(ufs);
 		exynos_ufs_ungate_clks(ufs);
@@ -1071,11 +1071,11 @@
 	}
 }
 
-static void exynos_ufs_post_hibern8(struct ufs_hba *hba, u8 enter)
+static void exynos_ufs_post_hibern8(struct ufs_hba *hba, enum uic_cmd_dme cmd)
 {
 	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
 
-	if (!enter) {
+	if (cmd == UIC_CMD_DME_HIBER_EXIT) {
 		u32 cur_mode = 0;
 		u32 pwrmode;
 
@@ -1094,7 +1094,7 @@
 
 		if (!(ufs->opts & EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB))
 			exynos_ufs_establish_connt(ufs);
-	} else {
+	} else if (cmd == UIC_CMD_DME_HIBER_ENTER) {
 		ufs->entry_hibern8_t = ktime_get();
 		exynos_ufs_gate_clks(ufs);
 		if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL)
@@ -1163,15 +1163,15 @@
 }
 
 static void exynos_ufs_hibern8_notify(struct ufs_hba *hba,
-				     enum uic_cmd_dme enter,
+				     enum uic_cmd_dme cmd,
 				     enum ufs_notify_change_status notify)
 {
 	switch ((u8)notify) {
 	case PRE_CHANGE:
-		exynos_ufs_pre_hibern8(hba, enter);
+		exynos_ufs_pre_hibern8(hba, cmd);
 		break;
 	case POST_CHANGE:
-		exynos_ufs_post_hibern8(hba, enter);
+		exynos_ufs_post_hibern8(hba, cmd);
 		break;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufs-mediatek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufs-mediatek.c
@@ -501,7 +501,7 @@
 	struct ufs_mtk_host *host = ufshcd_get_variant(hba);
 
 	host->reg_va09 = regulator_get(hba->dev, "va09");
-	if (!host->reg_va09)
+	if (IS_ERR(host->reg_va09))
 		dev_info(hba->dev, "failed to get va09");
 	else
 		host->caps |= UFS_MTK_CAP_VA09_PWR_CTRL;
@@ -949,7 +949,6 @@
 		 * ufshcd_suspend() re-enabling regulators while vreg is still
 		 * in low-power mode.
 		 */
-		ufs_mtk_vreg_set_lpm(hba, true);
 		err = ufs_mtk_mphy_power_on(hba, false);
 		if (err)
 			goto fail;
@@ -973,12 +972,13 @@
 {
 	int err;
 
+	if (hba->ufshcd_state != UFSHCD_STATE_OPERATIONAL)
+		ufs_mtk_vreg_set_lpm(hba, false);
+
 	err = ufs_mtk_mphy_power_on(hba, true);
 	if (err)
 		goto fail;
 
-	ufs_mtk_vreg_set_lpm(hba, false);
-
 	if (ufshcd_is_link_hibern8(hba)) {
 		err = ufs_mtk_link_set_hpm(hba);
 		if (err)
@@ -1139,9 +1139,59 @@
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+int ufs_mtk_system_suspend(struct device *dev)
+{
+	struct ufs_hba *hba = dev_get_drvdata(dev);
+	int ret;
+
+	ret = ufshcd_system_suspend(dev);
+	if (ret)
+		return ret;
+
+	ufs_mtk_vreg_set_lpm(hba, true);
+
+	return 0;
+}
+
+int ufs_mtk_system_resume(struct device *dev)
+{
+	struct ufs_hba *hba = dev_get_drvdata(dev);
+
+	ufs_mtk_vreg_set_lpm(hba, false);
+
+	return ufshcd_system_resume(dev);
+}
+#endif
+
+int ufs_mtk_runtime_suspend(struct device *dev)
+{
+	struct ufs_hba *hba = dev_get_drvdata(dev);
+	int ret = 0;
+
+	ret = ufshcd_runtime_suspend(dev);
+	if (ret)
+		return ret;
+
+	ufs_mtk_vreg_set_lpm(hba, true);
+
+	return 0;
+}
+
+int ufs_mtk_runtime_resume(struct device *dev)
+{
+	struct ufs_hba *hba = dev_get_drvdata(dev);
+
+	ufs_mtk_vreg_set_lpm(hba, false);
+
+	return ufshcd_runtime_resume(dev);
+}
+
 static const struct dev_pm_ops ufs_mtk_pm_ops = {
-	SET_SYSTEM_SLEEP_PM_OPS(ufshcd_system_suspend, ufshcd_system_resume)
-	SET_RUNTIME_PM_OPS(ufshcd_runtime_suspend, ufshcd_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(ufs_mtk_system_suspend,
+				ufs_mtk_system_resume)
+	SET_RUNTIME_PM_OPS(ufs_mtk_runtime_suspend,
+			   ufs_mtk_runtime_resume, NULL)
 	.prepare	 = ufshcd_suspend_prepare,
 	.complete	 = ufshcd_resume_complete,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufs-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufs-qcom.c
@@ -242,8 +242,9 @@
 	ufshcd_rmwl(host->hba, QUNIPRO_SEL,
 		   ufs_qcom_cap_qunipro(host) ? QUNIPRO_SEL : 0,
 		   REG_UFS_CFG1);
-	/* make sure above configuration is applied before we return */
-	mb();
+
+	if (host->hw_ver.major >= 0x05)
+		ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0);
 }
 
 /*
@@ -352,7 +353,7 @@
 		REG_UFS_CFG2);
 
 	/* Ensure that HW clock gating is enabled before next operations */
-	mb();
+	ufshcd_readl(hba, REG_UFS_CFG2);
 }
 
 static int ufs_qcom_hce_enable_notify(struct ufs_hba *hba,
@@ -449,7 +450,7 @@
 		 * make sure above write gets applied before we return from
 		 * this function.
 		 */
-		mb();
+		ufshcd_readl(hba, REG_UFS_SYS1CLK_1US);
 	}
 
 	if (ufs_qcom_cap_qunipro(host))
@@ -515,9 +516,9 @@
 		mb();
 	}
 
-	if (update_link_startup_timer) {
+	if (update_link_startup_timer && host->hw_ver.major != 0x5) {
 		ufshcd_writel(hba, ((core_clk_rate / MSEC_PER_SEC) * 100),
-			      REG_UFS_PA_LINK_STARTUP_TIMER);
+			      REG_UFS_CFG0);
 		/*
 		 * make sure that this configuration is applied before
 		 * we return
@@ -637,12 +638,7 @@
 			return err;
 	}
 
-	err = ufs_qcom_ice_resume(host);
-	if (err)
-		return err;
-
-	hba->is_sys_suspended = false;
-	return 0;
+	return ufs_qcom_ice_resume(host);
 }
 
 static void ufs_qcom_dev_ref_clk_ctrl(struct ufs_qcom_host *host, bool enable)
@@ -683,8 +679,11 @@
 
 		writel_relaxed(temp, host->dev_ref_clk_ctrl_mmio);
 
-		/* ensure that ref_clk is enabled/disabled before we return */
-		wmb();
+		/*
+		 * Make sure the write to ref_clk reaches the destination and
+		 * not stored in a Write Buffer (WB).
+		 */
+		readl(host->dev_ref_clk_ctrl_mmio);
 
 		/*
 		 * If we call hibern8 exit after this, we need to make sure that
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufs-qcom.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufs-qcom.h
@@ -35,8 +35,10 @@
 	REG_UFS_TX_SYMBOL_CLK_NS_US         = 0xC4,
 	REG_UFS_LOCAL_PORT_ID_REG           = 0xC8,
 	REG_UFS_PA_ERR_CODE                 = 0xCC,
-	REG_UFS_RETRY_TIMER_REG             = 0xD0,
-	REG_UFS_PA_LINK_STARTUP_TIMER       = 0xD8,
+	/* On older UFS revisions, this register is called "RETRY_TIMER_REG" */
+	REG_UFS_PARAM0                      = 0xD0,
+	/* On older UFS revisions, this register is called "REG_UFS_PA_LINK_STARTUP_TIMER" */
+	REG_UFS_CFG0                        = 0xD8,
 	REG_UFS_CFG1                        = 0xDC,
 	REG_UFS_CFG2                        = 0xE0,
 	REG_UFS_HW_VERSION                  = 0xE4,
@@ -74,6 +76,9 @@
 #define UFS_CNTLR_2_x_x_VEN_REGS_OFFSET(x)	(0x000 + x)
 #define UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(x)	(0x400 + x)
 
+/* bit definitions for REG_UFS_CFG0 register */
+#define QUNIPRO_G4_SEL		BIT(5)
+
 /* bit definitions for REG_UFS_CFG1 register */
 #define QUNIPRO_SEL		0x1
 #define UTP_DBG_RAMS_EN		0x20000
@@ -145,10 +150,10 @@
 			1 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1);
 
 	/*
-	 * Make sure assertion of ufs phy reset is written to
-	 * register before returning
+	 * Dummy read to ensure the write takes effect before doing any sort
+	 * of delay
 	 */
-	mb();
+	ufshcd_readl(hba, REG_UFS_CFG1);
 }
 
 static inline void ufs_qcom_deassert_reset(struct ufs_hba *hba)
@@ -157,10 +162,10 @@
 			0 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1);
 
 	/*
-	 * Make sure de-assertion of ufs phy reset is written to
-	 * register before returning
+	 * Dummy read to ensure the write takes effect before doing any sort
+	 * of delay
 	 */
-	mb();
+	ufshcd_readl(hba, REG_UFS_CFG1);
 }
 
 /* Host controller hardware version: major.minor.step */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufs-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufs-sysfs.c
@@ -371,6 +371,9 @@
 	struct ufs_hba *hba = dev_get_drvdata(dev);
 	struct ufs_hba_monitor *m = &hba->monitor;
 
+	if (!m->nr_req[READ])
+		return sysfs_emit(buf, "0\n");
+
 	return sysfs_emit(buf, "%llu\n", div_u64(ktime_to_us(m->lat_sum[READ]),
 						 m->nr_req[READ]));
 }
@@ -438,6 +441,9 @@
 	struct ufs_hba *hba = dev_get_drvdata(dev);
 	struct ufs_hba_monitor *m = &hba->monitor;
 
+	if (!m->nr_req[WRITE])
+		return sysfs_emit(buf, "0\n");
+
 	return sysfs_emit(buf, "%llu\n", div_u64(ktime_to_us(m->lat_sum[WRITE]),
 						 m->nr_req[WRITE]));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufs_bsg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufs_bsg.c
@@ -213,6 +213,7 @@
 	q = bsg_setup_queue(bsg_dev, dev_name(bsg_dev), ufs_bsg_request, NULL, 0);
 	if (IS_ERR(q)) {
 		ret = PTR_ERR(q);
+		device_del(bsg_dev);
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshcd-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshcd-pci.c
@@ -421,6 +421,19 @@
 	return err;
 }
 
+static int ufs_intel_adl_init(struct ufs_hba *hba)
+{
+	hba->nop_out_timeout = 200;
+	hba->quirks |= UFSHCD_QUIRK_BROKEN_AUTO_HIBERN8;
+	return ufs_intel_common_init(hba);
+}
+
+static int ufs_intel_mtl_init(struct ufs_hba *hba)
+{
+	hba->caps |= UFSHCD_CAP_CRYPTO | UFSHCD_CAP_WB_EN;
+	return ufs_intel_common_init(hba);
+}
+
 static struct ufs_hba_variant_ops ufs_intel_cnl_hba_vops = {
 	.name                   = "intel-pci",
 	.init			= ufs_intel_common_init,
@@ -449,6 +462,25 @@
 	.device_reset		= ufs_intel_device_reset,
 };
 
+static struct ufs_hba_variant_ops ufs_intel_adl_hba_vops = {
+	.name			= "intel-pci",
+	.init			= ufs_intel_adl_init,
+	.exit			= ufs_intel_common_exit,
+	.link_startup_notify	= ufs_intel_link_startup_notify,
+	.resume			= ufs_intel_resume,
+	.device_reset		= ufs_intel_device_reset,
+};
+
+static struct ufs_hba_variant_ops ufs_intel_mtl_hba_vops = {
+	.name                   = "intel-pci",
+	.init			= ufs_intel_mtl_init,
+	.exit			= ufs_intel_common_exit,
+	.hce_enable_notify	= ufs_intel_hce_enable_notify,
+	.link_startup_notify	= ufs_intel_link_startup_notify,
+	.resume			= ufs_intel_resume,
+	.device_reset		= ufs_intel_device_reset,
+};
+
 #ifdef CONFIG_PM_SLEEP
 static int ufshcd_pci_restore(struct device *dev)
 {
@@ -522,8 +554,6 @@
 		return err;
 	}
 
-	pci_set_drvdata(pdev, hba);
-
 	hba->vops = (struct ufs_hba_variant_ops *)id->driver_data;
 
 	err = ufshcd_init(hba, mmio_base, pdev->irq);
@@ -563,6 +593,10 @@
 	{ PCI_VDEVICE(INTEL, 0x4B41), (kernel_ulong_t)&ufs_intel_ehl_hba_vops },
 	{ PCI_VDEVICE(INTEL, 0x4B43), (kernel_ulong_t)&ufs_intel_ehl_hba_vops },
 	{ PCI_VDEVICE(INTEL, 0x98FA), (kernel_ulong_t)&ufs_intel_lkf_hba_vops },
+	{ PCI_VDEVICE(INTEL, 0x51FF), (kernel_ulong_t)&ufs_intel_adl_hba_vops },
+	{ PCI_VDEVICE(INTEL, 0x54FF), (kernel_ulong_t)&ufs_intel_adl_hba_vops },
+	{ PCI_VDEVICE(INTEL, 0x7E47), (kernel_ulong_t)&ufs_intel_mtl_hba_vops },
+	{ PCI_VDEVICE(INTEL, 0xA847), (kernel_ulong_t)&ufs_intel_mtl_hba_vops },
 	{ }	/* terminate list */
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshcd-pltfrm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshcd-pltfrm.c
@@ -91,7 +91,12 @@
 
 		clki->min_freq = clkfreq[i];
 		clki->max_freq = clkfreq[i+1];
-		clki->name = kstrdup(name, GFP_KERNEL);
+		clki->name = devm_kstrdup(dev, name, GFP_KERNEL);
+		if (!clki->name) {
+			ret = -ENOMEM;
+			goto out;
+		}
+
 		if (!strcmp(name, "ref_clk"))
 			clki->keep_link_active = true;
 		dev_dbg(dev, "%s: min %u max %u name %s\n", "freq-table-hz",
@@ -102,9 +107,20 @@
 	return ret;
 }
 
+static bool phandle_exists(const struct device_node *np,
+			   const char *phandle_name, int index)
+{
+	struct device_node *parse_np = of_parse_phandle(np, phandle_name, index);
+
+	if (parse_np)
+		of_node_put(parse_np);
+
+	return parse_np != NULL;
+}
+
 #define MAX_PROP_SIZE 32
 static int ufshcd_populate_vreg(struct device *dev, const char *name,
-		struct ufs_vreg **out_vreg)
+				struct ufs_vreg **out_vreg)
 {
 	char prop_name[MAX_PROP_SIZE];
 	struct ufs_vreg *vreg = NULL;
@@ -116,7 +132,7 @@
 	}
 
 	snprintf(prop_name, MAX_PROP_SIZE, "%s-supply", name);
-	if (!of_parse_phandle(np, prop_name, 0)) {
+	if (!phandle_exists(np, prop_name, 0)) {
 		dev_info(dev, "%s: Unable to find %s regulator, assuming enabled\n",
 				__func__, prop_name);
 		goto out;
@@ -126,7 +142,9 @@
 	if (!vreg)
 		return -ENOMEM;
 
-	vreg->name = kstrdup(name, GFP_KERNEL);
+	vreg->name = devm_kstrdup(dev, name, GFP_KERNEL);
+	if (!vreg->name)
+		return -ENOMEM;
 
 	snprintf(prop_name, MAX_PROP_SIZE, "%s-max-microamp", name);
 	if (of_property_read_u32(np, prop_name, &vreg->max_uA)) {
@@ -361,8 +379,6 @@
 		goto dealloc_host;
 	}
 
-	platform_set_drvdata(pdev, hba);
-
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshcd.c
@@ -112,8 +112,13 @@
 	if (!regs)
 		return -ENOMEM;
 
-	for (pos = 0; pos < len; pos += 4)
+	for (pos = 0; pos < len; pos += 4) {
+		if (offset == 0 &&
+		    pos >= REG_UIC_ERROR_CODE_PHY_ADAPTER_LAYER &&
+		    pos <= REG_UIC_ERROR_CODE_DME)
+			continue;
 		regs[pos / 4] = ufshcd_readl(hba, offset + pos);
+	}
 
 	ufshcd_hex_dump(prefix, regs, len);
 	kfree(regs);
@@ -125,8 +130,9 @@
 enum {
 	UFSHCD_MAX_CHANNEL	= 0,
 	UFSHCD_MAX_ID		= 1,
-	UFSHCD_CMD_PER_LUN	= 32,
-	UFSHCD_CAN_QUEUE	= 32,
+	UFSHCD_NUM_RESERVED	= 1,
+	UFSHCD_CMD_PER_LUN	= 32 - UFSHCD_NUM_RESERVED,
+	UFSHCD_CAN_QUEUE	= 32 - UFSHCD_NUM_RESERVED,
 };
 
 /* UFSHCD error handling flags */
@@ -222,8 +228,7 @@
 static int ufshcd_eh_host_reset_handler(struct scsi_cmnd *cmd);
 static int ufshcd_clear_tm_cmd(struct ufs_hba *hba, int tag);
 static void ufshcd_hba_exit(struct ufs_hba *hba);
-static int ufshcd_clear_ua_wluns(struct ufs_hba *hba);
-static int ufshcd_probe_hba(struct ufs_hba *hba, bool async);
+static int ufshcd_probe_hba(struct ufs_hba *hba, bool init_dev_params);
 static int ufshcd_setup_clocks(struct ufs_hba *hba, bool on);
 static int ufshcd_uic_hibern8_enter(struct ufs_hba *hba);
 static inline void ufshcd_add_delay_before_dme_cmd(struct ufs_hba *hba);
@@ -358,7 +363,7 @@
 static void ufshcd_add_command_trace(struct ufs_hba *hba, unsigned int tag,
 				     enum ufs_trace_str_t str_t)
 {
-	u64 lba;
+	u64 lba = 0;
 	u8 opcode = 0, group_id = 0;
 	u32 intr, doorbell;
 	struct ufshcd_lrb *lrbp = &hba->lrb[tag];
@@ -375,7 +380,6 @@
 		return;
 
 	opcode = cmd->cmnd[0];
-	lba = scsi_get_lba(cmd);
 
 	if (opcode == READ_10 || opcode == WRITE_10) {
 		/*
@@ -383,6 +387,7 @@
 		 */
 		transfer_len =
 		       be32_to_cpu(lrbp->ucd_req_ptr->sc.exp_data_transfer_len);
+		lba = scsi_get_lba(cmd);
 		if (opcode == WRITE_10)
 			group_id = lrbp->cmd->cmnd[6];
 	} else if (opcode == UNMAP) {
@@ -390,6 +395,7 @@
 		 * The number of Bytes to be unmapped beginning with the lba.
 		 */
 		transfer_len = blk_rq_bytes(rq);
+		lba = scsi_get_lba(cmd);
 	}
 
 	intr = ufshcd_readl(hba, REG_INTERRUPT_STATUS);
@@ -576,7 +582,12 @@
 		"INVALID MODE",
 	};
 
-	dev_err(hba->dev, "%s:[RX, TX]: gear=[%d, %d], lane[%d, %d], pwr[%s, %s], rate = %d\n",
+	/*
+	 * Using dev_dbg to avoid messages during runtime PM to avoid
+	 * never-ending cycles of messages written back to storage by user space
+	 * causing runtime resume, causing more messages and so on.
+	 */
+	dev_dbg(hba->dev, "%s:[RX, TX]: gear=[%d, %d], lane[%d, %d], pwr[%s, %s], rate = %d\n",
 		 __func__,
 		 hba->pwr_info.gear_rx, hba->pwr_info.gear_tx,
 		 hba->pwr_info.lane_rx, hba->pwr_info.lane_tx,
@@ -1174,12 +1185,14 @@
 	 * clock scaling is in progress
 	 */
 	ufshcd_scsi_block_requests(hba);
+	mutex_lock(&hba->wb_mutex);
 	down_write(&hba->clk_scaling_lock);
 
 	if (!hba->clk_scaling.is_allowed ||
 	    ufshcd_wait_for_doorbell_clr(hba, DOORBELL_CLR_TOUT_US)) {
 		ret = -EBUSY;
 		up_write(&hba->clk_scaling_lock);
+		mutex_unlock(&hba->wb_mutex);
 		ufshcd_scsi_unblock_requests(hba);
 		goto out;
 	}
@@ -1191,12 +1204,15 @@
 	return ret;
 }
 
-static void ufshcd_clock_scaling_unprepare(struct ufs_hba *hba, bool writelock)
+static void ufshcd_clock_scaling_unprepare(struct ufs_hba *hba, int err, bool scale_up)
 {
-	if (writelock)
-		up_write(&hba->clk_scaling_lock);
-	else
-		up_read(&hba->clk_scaling_lock);
+	up_write(&hba->clk_scaling_lock);
+
+	/* Enable Write Booster if we have scaled up else disable it */
+	ufshcd_wb_toggle(hba, scale_up);
+
+	mutex_unlock(&hba->wb_mutex);
+
 	ufshcd_scsi_unblock_requests(hba);
 	ufshcd_release(hba);
 }
@@ -1213,7 +1229,6 @@
 static int ufshcd_devfreq_scale(struct ufs_hba *hba, bool scale_up)
 {
 	int ret = 0;
-	bool is_writelock = true;
 
 	ret = ufshcd_clock_scaling_prepare(hba);
 	if (ret)
@@ -1242,13 +1257,8 @@
 		}
 	}
 
-	/* Enable Write Booster if we have scaled up else disable it */
-	downgrade_write(&hba->clk_scaling_lock);
-	is_writelock = false;
-	ufshcd_wb_toggle(hba, scale_up);
-
 out_unprepare:
-	ufshcd_clock_scaling_unprepare(hba, is_writelock);
+	ufshcd_clock_scaling_unprepare(hba, ret, scale_up);
 	return ret;
 }
 
@@ -1658,7 +1668,8 @@
 	bool flush_result;
 	unsigned long flags;
 
-	if (!ufshcd_is_clkgating_allowed(hba))
+	if (!ufshcd_is_clkgating_allowed(hba) ||
+	    !hba->clk_gating.is_initialized)
 		goto out;
 	spin_lock_irqsave(hba->host->host_lock, flags);
 	hba->clk_gating.active_reqs++;
@@ -1818,7 +1829,7 @@
 
 	if (hba->clk_gating.active_reqs || hba->clk_gating.is_suspended ||
 	    hba->ufshcd_state != UFSHCD_STATE_OPERATIONAL ||
-	    hba->outstanding_tasks ||
+	    hba->outstanding_tasks || !hba->clk_gating.is_initialized ||
 	    hba->active_uic_cmd || hba->uic_async_done ||
 	    hba->clk_gating.state == CLKS_OFF)
 		return;
@@ -1953,11 +1964,15 @@
 {
 	if (!hba->clk_gating.is_initialized)
 		return;
+
 	ufshcd_remove_clk_gating_sysfs(hba);
-	cancel_work_sync(&hba->clk_gating.ungate_work);
-	cancel_delayed_work_sync(&hba->clk_gating.gate_work);
-	destroy_workqueue(hba->clk_gating.clk_gating_workq);
+
+	/* Ungate the clock if necessary. */
+	ufshcd_hold(hba, false);
 	hba->clk_gating.is_initialized = false;
+	ufshcd_release(hba);
+
+	destroy_workqueue(hba->clk_gating.clk_gating_workq);
 }
 
 /* Must be called with host lock acquired */
@@ -2181,6 +2196,7 @@
 	hba->nutrs = (hba->capabilities & MASK_TRANSFER_REQUESTS_SLOTS) + 1;
 	hba->nutmrs =
 	((hba->capabilities & MASK_TASK_MANAGEMENT_REQUEST_SLOTS) >> 16) + 1;
+	hba->reserved_slot = hba->nutrs - 1;
 
 	/* Read crypto capabilities */
 	err = ufshcd_hba_init_crypto_capabilities(hba);
@@ -2293,7 +2309,6 @@
 		      bool completion)
 {
 	lockdep_assert_held(&hba->uic_cmd_mutex);
-	lockdep_assert_held(hba->host->host_lock);
 
 	if (!ufshcd_ready_for_uic_cmd(hba)) {
 		dev_err(hba->dev,
@@ -2320,15 +2335,12 @@
 int ufshcd_send_uic_cmd(struct ufs_hba *hba, struct uic_command *uic_cmd)
 {
 	int ret;
-	unsigned long flags;
 
 	ufshcd_hold(hba, false);
 	mutex_lock(&hba->uic_cmd_mutex);
 	ufshcd_add_delay_before_dme_cmd(hba);
 
-	spin_lock_irqsave(hba->host->host_lock, flags);
 	ret = __ufshcd_send_uic_cmd(hba, uic_cmd, true);
-	spin_unlock_irqrestore(hba->host->host_lock, flags);
 	if (!ret)
 		ret = ufshcd_wait_for_uic_cmd(hba, uic_cmd);
 
@@ -2683,6 +2695,12 @@
 	if (!down_read_trylock(&hba->clk_scaling_lock))
 		return SCSI_MLQUEUE_HOST_BUSY;
 
+	/*
+	 * Allows the UFS error handler to wait for prior ufshcd_queuecommand()
+	 * calls.
+	 */
+	rcu_read_lock();
+
 	switch (hba->ufshcd_state) {
 	case UFSHCD_STATE_OPERATIONAL:
 	case UFSHCD_STATE_EH_SCHEDULED_NON_FATAL:
@@ -2749,7 +2767,10 @@
 	}
 
 	ufshcd_send_command(hba, tag);
+
 out:
+	rcu_read_unlock();
+
 	up_read(&hba->clk_scaling_lock);
 
 	if (ufs_trigger_eh()) {
@@ -2906,30 +2927,15 @@
 static int ufshcd_exec_dev_cmd(struct ufs_hba *hba,
 		enum dev_cmd_type cmd_type, int timeout)
 {
-	struct request_queue *q = hba->cmd_queue;
 	DECLARE_COMPLETION_ONSTACK(wait);
-	struct request *req;
+	const u32 tag = hba->reserved_slot;
 	struct ufshcd_lrb *lrbp;
 	int err;
-	int tag;
 
-	down_read(&hba->clk_scaling_lock);
+	/* Protects use of hba->reserved_slot. */
+	lockdep_assert_held(&hba->dev_cmd.lock);
 
-	/*
-	 * Get free slot, sleep if slots are unavailable.
-	 * Even though we use wait_event() which sleeps indefinitely,
-	 * the maximum wait time is bounded by SCSI request timeout.
-	 */
-	req = blk_get_request(q, REQ_OP_DRV_OUT, 0);
-	if (IS_ERR(req)) {
-		err = PTR_ERR(req);
-		goto out_unlock;
-	}
-	tag = req->tag;
-	WARN_ONCE(tag < 0, "Invalid tag %d\n", tag);
-	/* Set the timeout such that the SCSI error handler is not activated. */
-	req->timeout = msecs_to_jiffies(2 * timeout);
-	blk_mq_start_request(req);
+	down_read(&hba->clk_scaling_lock);
 
 	lrbp = &hba->lrb[tag];
 	WARN_ON(lrbp->cmd);
@@ -2947,8 +2953,6 @@
 				    (struct utp_upiu_req *)lrbp->ucd_rsp_ptr);
 
 out:
-	blk_put_request(req);
-out_unlock:
 	up_read(&hba->clk_scaling_lock);
 	return err;
 }
@@ -3461,7 +3465,7 @@
 		 */
 		ret = utf16s_to_utf8s(uc_str->uc,
 				      uc_str->len - QUERY_DESC_HDR_SIZE,
-				      UTF16_BIG_ENDIAN, str, ascii_len);
+				      UTF16_BIG_ENDIAN, str, ascii_len - 1);
 
 		/* replace non-printable or non-ASCII characters with spaces */
 		for (i = 0; i < ret; i++)
@@ -3791,11 +3795,16 @@
 			min_sleep_time_us =
 				MIN_DELAY_BEFORE_DME_CMDS_US - delta;
 		else
-			return; /* no more delay required */
+			min_sleep_time_us = 0; /* no more delay required */
 	}
 
-	/* allow sleep for extra 50us if needed */
-	usleep_range(min_sleep_time_us, min_sleep_time_us + 50);
+	if (min_sleep_time_us > 0) {
+		/* allow sleep for extra 50us if needed */
+		usleep_range(min_sleep_time_us, min_sleep_time_us + 50);
+	}
+
+	/* update the last_dme_cmd_tstamp */
+	hba->last_dme_cmd_tstamp = ktime_get();
 }
 
 /**
@@ -3956,11 +3965,11 @@
 		 * Make sure UIC command completion interrupt is disabled before
 		 * issuing UIC command.
 		 */
-		wmb();
+		ufshcd_readl(hba, REG_INTERRUPT_ENABLE);
 		reenable_intr = true;
 	}
-	ret = __ufshcd_send_uic_cmd(hba, cmd, false);
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
+	ret = __ufshcd_send_uic_cmd(hba, cmd, false);
 	if (ret) {
 		dev_err(hba->dev,
 			"pwr ctrl cmd 0x%x with mode 0x%x uic error %d\n",
@@ -4073,8 +4082,6 @@
 	if (ret)
 		dev_err(hba->dev, "%s: link recovery failed, err %d",
 			__func__, ret);
-	else
-		ufshcd_clear_ua_wluns(hba);
 
 	return ret;
 }
@@ -4980,6 +4987,12 @@
 		pm_runtime_get_noresume(&sdev->sdev_gendev);
 	else if (ufshcd_is_rpm_autosuspend_allowed(hba))
 		sdev->rpm_autosuspend = 1;
+	/*
+	 * Do not print messages during runtime PM to avoid never-ending cycles
+	 * of messages written back to storage by user space causing runtime
+	 * resume, causing more messages and so on.
+	 */
+	sdev->silence_suspend = 1;
 
 	ufshcd_crypto_setup_rq_keyslot_manager(hba, q);
 
@@ -5634,7 +5647,7 @@
 	}
 
 	hba->dev_info.wb_enabled = enable;
-	dev_info(hba->dev, "%s Write Booster %s\n",
+	dev_dbg(hba->dev, "%s Write Booster %s\n",
 			__func__, enable ? "enabled" : "disabled");
 
 	return ret;
@@ -5896,11 +5909,21 @@
 	}
 }
 
+static void ufshcd_force_error_recovery(struct ufs_hba *hba)
+{
+	spin_lock_irq(hba->host->host_lock);
+	hba->force_reset = true;
+	ufshcd_schedule_eh_work(hba);
+	spin_unlock_irq(hba->host->host_lock);
+}
+
 static void ufshcd_clk_scaling_allow(struct ufs_hba *hba, bool allow)
 {
+	mutex_lock(&hba->wb_mutex);
 	down_write(&hba->clk_scaling_lock);
 	hba->clk_scaling.is_allowed = allow;
 	up_write(&hba->clk_scaling_lock);
+	mutex_unlock(&hba->wb_mutex);
 }
 
 static void ufshcd_clk_scaling_suspend(struct ufs_hba *hba, bool suspend)
@@ -5948,8 +5971,7 @@
 	}
 	ufshcd_scsi_block_requests(hba);
 	/* Drain ufshcd_queuecommand() */
-	down_write(&hba->clk_scaling_lock);
-	up_write(&hba->clk_scaling_lock);
+	synchronize_rcu();
 	cancel_work_sync(&hba->eeh_work);
 }
 
@@ -5959,7 +5981,6 @@
 	ufshcd_release(hba);
 	if (ufshcd_is_clkscaling_supported(hba))
 		ufshcd_clk_scaling_suspend(hba, false);
-	ufshcd_clear_ua_wluns(hba);
 	ufshcd_rpm_put(hba);
 }
 
@@ -6386,9 +6407,8 @@
 	irqreturn_t ret = IRQ_NONE;
 	int tag;
 
-	pending = ufshcd_readl(hba, REG_UTP_TASK_REQ_DOOR_BELL);
-
 	spin_lock_irqsave(hba->host->host_lock, flags);
+	pending = ufshcd_readl(hba, REG_UTP_TASK_REQ_DOOR_BELL);
 	issued = hba->outstanding_tasks & ~pending;
 	for_each_set_bit(tag, &issued, hba->nutmrs) {
 		struct request *req = hba->tmf_rqs[tag];
@@ -6545,11 +6565,6 @@
 	err = wait_for_completion_io_timeout(&wait,
 			msecs_to_jiffies(TM_CMD_TIMEOUT));
 	if (!err) {
-		/*
-		 * Make sure that ufshcd_compl_tm() does not trigger a
-		 * use-after-free.
-		 */
-		req->end_io_data = NULL;
 		ufshcd_add_tm_upiu_trace(hba, task_tag, UFS_TM_ERR);
 		dev_err(hba->dev, "%s: task management cmd 0x%.2x timed-out\n",
 				__func__, tm_function);
@@ -6645,28 +6660,16 @@
 					enum dev_cmd_type cmd_type,
 					enum query_opcode desc_op)
 {
-	struct request_queue *q = hba->cmd_queue;
 	DECLARE_COMPLETION_ONSTACK(wait);
-	struct request *req;
+	const u32 tag = hba->reserved_slot;
 	struct ufshcd_lrb *lrbp;
 	int err = 0;
-	int tag;
 	u8 upiu_flags;
 
-	down_read(&hba->clk_scaling_lock);
-
-	req = blk_get_request(q, REQ_OP_DRV_OUT, 0);
-	if (IS_ERR(req)) {
-		err = PTR_ERR(req);
-		goto out_unlock;
-	}
-	tag = req->tag;
-	WARN_ONCE(tag < 0, "Invalid tag %d\n", tag);
+	/* Protects use of hba->reserved_slot. */
+	lockdep_assert_held(&hba->dev_cmd.lock);
 
-	if (unlikely(test_bit(tag, &hba->outstanding_reqs))) {
-		err = -EBUSY;
-		goto out;
-	}
+	down_read(&hba->clk_scaling_lock);
 
 	lrbp = &hba->lrb[tag];
 	WARN_ON(lrbp->cmd);
@@ -6735,9 +6738,6 @@
 	ufshcd_add_query_upiu_trace(hba, err ? UFS_QUERY_ERR : UFS_QUERY_COMP,
 				    (struct utp_upiu_req *)lrbp->ucd_rsp_ptr);
 
-out:
-	blk_put_request(req);
-out_unlock:
 	up_read(&hba->clk_scaling_lock);
 	return err;
 }
@@ -7044,6 +7044,7 @@
 		goto release;
 	}
 
+	lrbp->cmd = NULL;
 	err = SUCCESS;
 
 release:
@@ -7233,7 +7234,13 @@
 
 	if (!hba->vreg_info.vcc || !hba->vreg_info.vccq ||
 						!hba->vreg_info.vccq2) {
-		dev_err(hba->dev,
+		/*
+		 * Using dev_dbg to avoid messages during runtime PM to avoid
+		 * never-ending cycles of messages written back to storage by
+		 * user space causing runtime resume, causing more messages and
+		 * so on.
+		 */
+		dev_dbg(hba->dev,
 			"%s: Regulator capability was not set, actvIccLevel=%d",
 							__func__, icc_level);
 		goto out;
@@ -7875,8 +7882,6 @@
 	if (ret)
 		goto out;
 
-	ufshcd_clear_ua_wluns(hba);
-
 	/* Initialize devfreq after UFS device is detected */
 	if (ufshcd_is_clkscaling_supported(hba)) {
 		memcpy(&hba->clk_scaling.saved_pwr_info.info,
@@ -7896,122 +7901,11 @@
 	ufs_bsg_probe(hba);
 	ufshpb_init(hba);
 	scsi_scan_host(hba->host);
-	pm_runtime_put_sync(hba->dev);
 
 out:
 	return ret;
 }
 
-static void ufshcd_request_sense_done(struct request *rq, blk_status_t error)
-{
-	if (error != BLK_STS_OK)
-		pr_err("%s: REQUEST SENSE failed (%d)\n", __func__, error);
-	kfree(rq->end_io_data);
-	blk_put_request(rq);
-}
-
-static int
-ufshcd_request_sense_async(struct ufs_hba *hba, struct scsi_device *sdev)
-{
-	/*
-	 * Some UFS devices clear unit attention condition only if the sense
-	 * size used (UFS_SENSE_SIZE in this case) is non-zero.
-	 */
-	static const u8 cmd[6] = {REQUEST_SENSE, 0, 0, 0, UFS_SENSE_SIZE, 0};
-	struct scsi_request *rq;
-	struct request *req;
-	char *buffer;
-	int ret;
-
-	buffer = kzalloc(UFS_SENSE_SIZE, GFP_KERNEL);
-	if (!buffer)
-		return -ENOMEM;
-
-	req = blk_get_request(sdev->request_queue, REQ_OP_DRV_IN,
-			      /*flags=*/BLK_MQ_REQ_PM);
-	if (IS_ERR(req)) {
-		ret = PTR_ERR(req);
-		goto out_free;
-	}
-
-	ret = blk_rq_map_kern(sdev->request_queue, req,
-			      buffer, UFS_SENSE_SIZE, GFP_NOIO);
-	if (ret)
-		goto out_put;
-
-	rq = scsi_req(req);
-	rq->cmd_len = ARRAY_SIZE(cmd);
-	memcpy(rq->cmd, cmd, rq->cmd_len);
-	rq->retries = 3;
-	req->timeout = 1 * HZ;
-	req->rq_flags |= RQF_PM | RQF_QUIET;
-	req->end_io_data = buffer;
-
-	blk_execute_rq_nowait(/*bd_disk=*/NULL, req, /*at_head=*/true,
-			      ufshcd_request_sense_done);
-	return 0;
-
-out_put:
-	blk_put_request(req);
-out_free:
-	kfree(buffer);
-	return ret;
-}
-
-static int ufshcd_clear_ua_wlun(struct ufs_hba *hba, u8 wlun)
-{
-	struct scsi_device *sdp;
-	unsigned long flags;
-	int ret = 0;
-
-	spin_lock_irqsave(hba->host->host_lock, flags);
-	if (wlun == UFS_UPIU_UFS_DEVICE_WLUN)
-		sdp = hba->sdev_ufs_device;
-	else if (wlun == UFS_UPIU_RPMB_WLUN)
-		sdp = hba->sdev_rpmb;
-	else
-		BUG();
-	if (sdp) {
-		ret = scsi_device_get(sdp);
-		if (!ret && !scsi_device_online(sdp)) {
-			ret = -ENODEV;
-			scsi_device_put(sdp);
-		}
-	} else {
-		ret = -ENODEV;
-	}
-	spin_unlock_irqrestore(hba->host->host_lock, flags);
-	if (ret)
-		goto out_err;
-
-	ret = ufshcd_request_sense_async(hba, sdp);
-	scsi_device_put(sdp);
-out_err:
-	if (ret)
-		dev_err(hba->dev, "%s: UAC clear LU=%x ret = %d\n",
-				__func__, wlun, ret);
-	return ret;
-}
-
-static int ufshcd_clear_ua_wluns(struct ufs_hba *hba)
-{
-	int ret = 0;
-
-	if (!hba->wlun_dev_clr_ua)
-		goto out;
-
-	ret = ufshcd_clear_ua_wlun(hba, UFS_UPIU_UFS_DEVICE_WLUN);
-	if (!ret)
-		ret = ufshcd_clear_ua_wlun(hba, UFS_UPIU_RPMB_WLUN);
-	if (!ret)
-		hba->wlun_dev_clr_ua = false;
-out:
-	if (ret)
-		dev_err(hba->dev, "%s: Failed to clear UAC WLUNS ret = %d\n",
-				__func__, ret);
-	return ret;
-}
-
 /**
  * ufshcd_probe_hba - probe hba to detect device and initialize it
  * @hba: per-adapter instance
@@ -8062,8 +7956,6 @@
 	/* UFS device is also active now */
 	ufshcd_set_ufs_dev_active(hba);
 	ufshcd_force_reset_auto_bkops(hba);
-	hba->wlun_dev_clr_ua = true;
-	hba->wlun_rpmb_clr_ua = true;
 
 	/* Gear up to HS gear if supported */
 	if (hba->max_pwr_info.is_valid) {
@@ -8130,15 +8022,12 @@
 
 	/* Probe and add UFS logical units  */
 	ret = ufshcd_add_lus(hba);
+
 out:
-	/*
-	 * If we failed to initialize the device or the device is not
-	 * present, turn off the power/clocks etc.
-	 */
-	if (ret) {
-		pm_runtime_put_sync(hba->dev);
-		ufshcd_hba_exit(hba);
-	}
+	pm_runtime_put_sync(hba->dev);
+
+	if (ret)
+		dev_err(hba->dev, "%s failed: %d\n", __func__, ret);
 }
 
 static const struct attribute_group *ufshcd_driver_groups[] = {
@@ -8591,7 +8480,7 @@
  * @pwr_mode: device power mode to set
  *
  * Returns 0 if requested power mode is set successfully
- * Returns non-zero if failed to set the requested power mode
+ * Returns < 0 if failed to set the requested power mode
  */
 static int ufshcd_set_dev_pwr_mode(struct ufs_hba *hba,
 				     enum ufs_dev_pwr_mode pwr_mode)
@@ -8600,7 +8489,7 @@
 	struct scsi_sense_hdr sshdr;
 	struct scsi_device *sdp;
 	unsigned long flags;
-	int ret;
+	int ret, retries;
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
 	sdp = hba->sdev_ufs_device;
@@ -8625,8 +8514,6 @@
 	 * handling context.
 	 */
 	hba->host->eh_noresume = 1;
-	if (hba->wlun_dev_clr_ua)
-		ufshcd_clear_ua_wlun(hba, UFS_UPIU_UFS_DEVICE_WLUN);
 
 	cmd[4] = pwr_mode << 4;
 
@@ -8635,14 +8522,23 @@
 	 * callbacks hence set the RQF_PM flag so that it doesn't resume the
 	 * already suspended childs.
 	 */
-	ret = scsi_execute(sdp, cmd, DMA_NONE, NULL, 0, NULL, &sshdr,
-			START_STOP_TIMEOUT, 0, 0, RQF_PM, NULL);
+	for (retries = 3; retries > 0; --retries) {
+		ret = scsi_execute(sdp, cmd, DMA_NONE, NULL, 0, NULL, &sshdr,
+				   HZ, 0, 0, RQF_PM, NULL);
+		if (!scsi_status_is_check_condition(ret) ||
+				!scsi_sense_valid(&sshdr) ||
+				sshdr.sense_key != UNIT_ATTENTION)
+			break;
+	}
 	if (ret) {
 		sdev_printk(KERN_WARNING, sdp,
 			    "START_STOP failed for power mode: %d, result %x\n",
 			    pwr_mode, ret);
-		if (ret > 0 && scsi_sense_valid(&sshdr))
-			scsi_print_sense_hdr(sdp, NULL, &sshdr);
+		if (ret > 0) {
+			if (scsi_sense_valid(&sshdr))
+				scsi_print_sense_hdr(sdp, NULL, &sshdr);
+			ret = -EIO;
+		}
 	}
 
 	if (!ret)
@@ -8857,8 +8753,16 @@
 			 * that performance might be impacted.
 			 */
 			ret = ufshcd_urgent_bkops(hba);
-			if (ret)
+			if (ret) {
+				/*
+				 * If return err in suspend flow, IO will hang.
+				 * Trigger error handler and break suspend for
+				 * error recovery.
+				 */
+				ufshcd_force_error_recovery(hba);
+				ret = -EBUSY;
 				goto enable_scaling;
+			}
 		} else {
 			/* make sure that auto bkops is disabled */
 			ufshcd_disable_auto_bkops(hba);
@@ -8885,6 +8789,15 @@
 
 		if (!hba->dev_info.b_rpm_dev_flush_capable) {
 			ret = ufshcd_set_dev_pwr_mode(hba, req_dev_pwr_mode);
+			if (ret && pm_op != UFS_SHUTDOWN_PM) {
+				/*
+				 * If return err in suspend flow, IO will hang.
+				 * Trigger error handler and break suspend for
+				 * error recovery.
+				 */
+				ufshcd_force_error_recovery(hba);
+				ret = -EBUSY;
+			}
 			if (ret)
 				goto enable_scaling;
 		}
@@ -8896,6 +8809,15 @@
 	 */
 	check_for_bkops = !ufshcd_is_ufs_dev_deepsleep(hba);
 	ret = ufshcd_link_state_transition(hba, req_link_state, check_for_bkops);
+	if (ret && pm_op != UFS_SHUTDOWN_PM) {
+		/*
+		 * If return err in suspend flow, IO will hang.
+		 * Trigger error handler and break suspend for
+		 * error recovery.
+		 */
+		ufshcd_force_error_recovery(hba);
+		ret = -EBUSY;
+	}
 	if (ret)
 		goto set_dev_active;
 
@@ -9357,12 +9279,8 @@
 int ufshcd_shutdown(struct ufs_hba *hba)
 {
 	if (ufshcd_is_ufs_dev_poweroff(hba) && ufshcd_is_link_off(hba))
-		goto out;
-
-	pm_runtime_get_sync(hba->dev);
+		ufshcd_suspend(hba);
 
-	ufshcd_suspend(hba);
-out:
 	hba->is_powered = false;
 	/* allow force shutdown even in case of errors */
 	return 0;
@@ -9485,6 +9403,13 @@
 	struct device *dev = hba->dev;
 	char eh_wq_name[sizeof("ufs_eh_wq_00")];
 
+	/*
+	 * dev_set_drvdata() must be called before any callbacks are registered
+	 * that use dev_get_drvdata() (frequency scaling, clock scaling, hwmon,
+	 * sysfs).
+	 */
+	dev_set_drvdata(dev, hba);
+
 	if (!mmio_base) {
 		dev_err(hba->dev,
 		"Invalid memory reference for mmio_base is NULL\n");
@@ -9527,8 +9452,8 @@
 	/* Configure LRB */
 	ufshcd_host_memory_configure(hba);
 
-	host->can_queue = hba->nutrs;
-	host->cmd_per_lun = hba->nutrs;
+	host->can_queue = hba->nutrs - UFSHCD_NUM_RESERVED;
+	host->cmd_per_lun = hba->nutrs - UFSHCD_NUM_RESERVED;
 	host->max_id = UFSHCD_MAX_ID;
 	host->max_lun = UFS_MAX_LUNS;
 	host->max_channel = UFSHCD_MAX_CHANNEL;
@@ -9561,6 +9486,7 @@
 	/* Initialize mutex for exception event control */
 	mutex_init(&hba->ee_ctrl_mutex);
 
+	mutex_init(&hba->wb_mutex);
 	init_rwsem(&hba->clk_scaling_lock);
 
 	ufshcd_init_clk_gating(hba);
@@ -9579,7 +9505,7 @@
 	 * Make sure that UFS interrupts are disabled and any pending interrupt
 	 * status is cleared before registering UFS interrupt handler.
 	 */
-	mb();
+	ufshcd_readl(hba, REG_INTERRUPT_ENABLE);
 
 	/* IRQ registration */
 	err = devm_request_irq(dev, irq, ufshcd_intr, IRQF_SHARED, UFSHCD, hba);
@@ -9699,10 +9625,6 @@
 		ufshcd_rpm_put(hba);
 		hba->complete_put = false;
 	}
-	if (hba->rpmb_complete_put) {
-		ufshcd_rpmb_rpm_put(hba);
-		hba->rpmb_complete_put = false;
-	}
 }
 EXPORT_SYMBOL_GPL(ufshcd_resume_complete);
 
@@ -9725,10 +9647,6 @@
 		}
 		hba->complete_put = true;
 	}
-	if (hba->sdev_rpmb) {
-		ufshcd_rpmb_rpm_get_sync(hba);
-		hba->rpmb_complete_put = true;
-	}
 	return 0;
 }
 EXPORT_SYMBOL_GPL(ufshcd_suspend_prepare);
@@ -9797,49 +9715,6 @@
 	},
 };
 
-static int ufshcd_rpmb_probe(struct device *dev)
-{
-	return is_rpmb_wlun(to_scsi_device(dev)) ? 0 : -ENODEV;
-}
-
-static inline int ufshcd_clear_rpmb_uac(struct ufs_hba *hba)
-{
-	int ret = 0;
-
-	if (!hba->wlun_rpmb_clr_ua)
-		return 0;
-	ret = ufshcd_clear_ua_wlun(hba, UFS_UPIU_RPMB_WLUN);
-	if (!ret)
-		hba->wlun_rpmb_clr_ua = 0;
-	return ret;
-}
-
-#ifdef CONFIG_PM
-static int ufshcd_rpmb_resume(struct device *dev)
-{
-	struct ufs_hba *hba = wlun_dev_to_hba(dev);
-
-	if (hba->sdev_rpmb)
-		ufshcd_clear_rpmb_uac(hba);
-	return 0;
-}
-#endif
-
-static const struct dev_pm_ops ufs_rpmb_pm_ops = {
-	SET_RUNTIME_PM_OPS(NULL, ufshcd_rpmb_resume, NULL)
-	SET_SYSTEM_SLEEP_PM_OPS(NULL, ufshcd_rpmb_resume)
-};
-
-/* ufs_rpmb_wlun_template - Describes UFS RPMB WLUN. Used only to send UAC. */
-static struct scsi_driver ufs_rpmb_wlun_template = {
-	.gendrv = {
-		.name = "ufs_rpmb_wlun",
-		.owner = THIS_MODULE,
-		.probe = ufshcd_rpmb_probe,
-		.pm = &ufs_rpmb_pm_ops,
-	},
-};
-
 static int __init ufshcd_core_init(void)
 {
 	int ret;
@@ -9848,24 +9723,13 @@
 
 	ret = scsi_register_driver(&ufs_dev_wlun_template.gendrv);
 	if (ret)
-		goto debugfs_exit;
-
-	ret = scsi_register_driver(&ufs_rpmb_wlun_template.gendrv);
-	if (ret)
-		goto unregister;
-
-	return ret;
-unregister:
-	scsi_unregister_driver(&ufs_dev_wlun_template.gendrv);
-debugfs_exit:
-	ufs_debugfs_exit();
+		ufs_debugfs_exit();
 	return ret;
 }
 
 static void __exit ufshcd_core_exit(void)
 {
 	ufs_debugfs_exit();
-	scsi_unregister_driver(&ufs_rpmb_wlun_template.gendrv);
 	scsi_unregister_driver(&ufs_dev_wlun_template.gendrv);
 }
 
@@ -9875,5 +9739,6 @@
 MODULE_AUTHOR("Santosh Yaragnavi <santosh.sy@samsung.com>");
 MODULE_AUTHOR("Vinayak Holikatti <h.vinayak@samsung.com>");
 MODULE_DESCRIPTION("Generic UFS host controller driver Core");
+MODULE_SOFTDEP("pre: governor_simpleondemand");
 MODULE_LICENSE("GPL");
 MODULE_VERSION(UFSHCD_DRIVER_VERSION);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshcd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshcd.h
@@ -725,6 +725,7 @@
  * @capabilities: UFS Controller Capabilities
  * @nutrs: Transfer Request Queue depth supported by controller
  * @nutmrs: Task Management Queue depth supported by controller
+ * @reserved_slot: Used to submit device commands. Protected by @dev_cmd.lock.
  * @ufs_version: UFS Version to which controller complies
  * @vops: pointer to variant specific operations
  * @priv: pointer to variant specific private data
@@ -762,6 +763,7 @@
  * @urgent_bkops_lvl: keeps track of urgent bkops level for device
  * @is_urgent_bkops_lvl_checked: keeps track if the urgent bkops level for
  *  device is known or not.
+ * @wb_mutex: used to serialize devfreq and sysfs write booster toggling
  * @scsi_block_reqs_cnt: reference counting for scsi block requests
  * @crypto_capabilities: Content of crypto capabilities register (0x100)
  * @crypto_cap_array: Array of crypto capabilities
@@ -813,6 +815,7 @@
 	u32 capabilities;
 	int nutrs;
 	int nutmrs;
+	u32 reserved_slot;
 	u32 ufs_version;
 	const struct ufs_hba_variant_ops *vops;
 	struct ufs_hba_variant_params *vps;
@@ -871,9 +874,6 @@
 	struct ufs_vreg_info vreg_info;
 	struct list_head clk_list_head;
 
-	bool wlun_dev_clr_ua;
-	bool wlun_rpmb_clr_ua;
-
 	/* Number of requests aborts */
 	int req_abort_count;
 
@@ -893,6 +893,7 @@
 	enum bkops_status urgent_bkops_lvl;
 	bool is_urgent_bkops_lvl_checked;
 
+	struct mutex wb_mutex;
 	struct rw_semaphore clk_scaling_lock;
 	unsigned char desc_size[QUERY_DESC_IDN_MAX];
 	atomic_t scsi_block_reqs_cnt;
@@ -920,7 +921,6 @@
 #endif
 	u32 luns_avail;
 	bool complete_put;
-	bool rpmb_complete_put;
 };
 
 /* Returns true if clocks can be gated. Otherwise false */
@@ -1393,14 +1393,4 @@
 	return pm_runtime_put(&hba->sdev_ufs_device->sdev_gendev);
 }
 
-static inline int ufshcd_rpmb_rpm_get_sync(struct ufs_hba *hba)
-{
-	return pm_runtime_get_sync(&hba->sdev_rpmb->sdev_gendev);
-}
-
-static inline int ufshcd_rpmb_rpm_put(struct ufs_hba *hba)
-{
-	return pm_runtime_put(&hba->sdev_rpmb->sdev_gendev);
-}
-
 #endif /* End of Header */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshci.h
@@ -133,16 +133,13 @@
 
 #define UFSHCD_UIC_MASK		(UIC_COMMAND_COMPL | UFSHCD_UIC_PWR_MASK)
 
-#define UFSHCD_ERROR_MASK	(UIC_ERROR |\
-				DEVICE_FATAL_ERROR |\
-				CONTROLLER_FATAL_ERROR |\
-				SYSTEM_BUS_FATAL_ERROR |\
-				CRYPTO_ENGINE_FATAL_ERROR)
+#define UFSHCD_ERROR_MASK	(UIC_ERROR | INT_FATAL_ERRORS)
 
 #define INT_FATAL_ERRORS	(DEVICE_FATAL_ERROR |\
 				CONTROLLER_FATAL_ERROR |\
 				SYSTEM_BUS_FATAL_ERROR |\
-				CRYPTO_ENGINE_FATAL_ERROR)
+				CRYPTO_ENGINE_FATAL_ERROR |\
+				UIC_LINK_LOST)
 
 /* HCS - Host Controller Status 30h */
 #define DEVICE_PRESENT				0x1
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshpb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshpb.c
@@ -394,8 +394,6 @@
 	if (!ufshpb_is_supported_chunk(hpb, transfer_len))
 		return 0;
 
-	WARN_ON_ONCE(transfer_len > HPB_MULTI_CHUNK_HIGH);
-
 	if (hpb->is_hcm) {
 		/*
 		 * in host control mode, reads are the main source for
@@ -872,12 +870,6 @@
 	struct ufshpb_region *rgn, *victim_rgn = NULL;
 
 	list_for_each_entry(rgn, &lru_info->lh_lru_rgn, list_lru_rgn) {
-		if (!rgn) {
-			dev_err(&hpb->sdev_ufs_lu->sdev_dev,
-				"%s: no region allocated\n",
-				__func__);
-			return NULL;
-		}
 		if (ufshpb_check_srgns_issue_state(hpb, rgn))
 			continue;
 
@@ -893,6 +885,11 @@
 		break;
 	}
 
+	if (!victim_rgn)
+		dev_err(&hpb->sdev_ufs_lu->sdev_dev,
+			"%s: no region allocated\n",
+			__func__);
+
 	return victim_rgn;
 }
 
@@ -1260,6 +1257,13 @@
 	struct utp_hpb_rsp *rsp_field = &lrbp->ucd_rsp_ptr->hr;
 	int data_seg_len;
 
+	data_seg_len = be32_to_cpu(lrbp->ucd_rsp_ptr->header.dword_2)
+		& MASK_RSP_UPIU_DATA_SEG_LEN;
+
+	/* If data segment length is zero, rsp_field is not valid */
+	if (!data_seg_len)
+		return;
+
 	if (unlikely(lrbp->lun != rsp_field->lun)) {
 		struct scsi_device *sdev;
 		bool found = false;
@@ -1294,18 +1298,6 @@
 		return;
 	}
 
-	data_seg_len = be32_to_cpu(lrbp->ucd_rsp_ptr->header.dword_2)
-		& MASK_RSP_UPIU_DATA_SEG_LEN;
-
-	/* To flush remained rsp_list, we queue the map_work task */
-	if (!data_seg_len) {
-		if (!ufshpb_is_general_lun(hpb->lun))
-			return;
-
-		ufshpb_kick_map_work(hpb);
-		return;
-	}
-
 	BUILD_BUG_ON(sizeof(struct utp_hpb_rsp) != UTP_HPB_RSP_SIZE);
 
 	if (!ufshpb_is_hpb_rsp_valid(hba, lrbp, rsp_field))
@@ -1572,7 +1564,7 @@
 	if (ufshpb_is_legacy(hba))
 		hpb->pre_req_max_tr_len = HPB_LEGACY_CHUNK_HIGH;
 	else
-		hpb->pre_req_max_tr_len = HPB_MULTI_CHUNK_HIGH;
+		hpb->pre_req_max_tr_len = hpb_dev_info->max_hpb_single_cmd;
 
 	hpb->lu_pinned_start = hpb_lu_info->pinned_start;
 	hpb->lu_pinned_end = hpb_lu_info->num_pinned ?
@@ -2371,11 +2363,11 @@
 
 	ufshcd_map_desc_id_to_length(hba, QUERY_DESC_IDN_UNIT, &size);
 
-	pm_runtime_get_sync(hba->dev);
+	ufshcd_rpm_get_sync(hba);
 	ret = ufshcd_query_descriptor_retry(hba, UPIU_QUERY_OPCODE_READ_DESC,
 					    QUERY_DESC_IDN_UNIT, lun, 0,
 					    desc_buf, &size);
-	pm_runtime_put_sync(hba->dev);
+	ufshcd_rpm_put_sync(hba);
 
 	if (ret) {
 		dev_err(hba->dev,
@@ -2582,7 +2574,7 @@
 {
 	struct ufshpb_dev_info *hpb_dev_info = &hba->ufshpb_dev;
 	int version, ret;
-	u32 max_hpb_single_cmd = HPB_MULTI_CHUNK_LOW;
+	int max_single_cmd;
 
 	hpb_dev_info->control_mode = desc_buf[DEVICE_DESC_PARAM_HPB_CONTROL];
 
@@ -2598,21 +2590,22 @@
 	if (version == HPB_SUPPORT_LEGACY_VERSION)
 		hpb_dev_info->is_legacy = true;
 
-	pm_runtime_get_sync(hba->dev);
-	ret = ufshcd_query_attr_retry(hba, UPIU_QUERY_OPCODE_READ_ATTR,
-		QUERY_ATTR_IDN_MAX_HPB_SINGLE_CMD, 0, 0, &max_hpb_single_cmd);
-	pm_runtime_put_sync(hba->dev);
-
-	if (ret)
-		dev_err(hba->dev, "%s: idn: read max size of single hpb cmd query request failed",
-			__func__);
-	hpb_dev_info->max_hpb_single_cmd = max_hpb_single_cmd;
-
 	/*
 	 * Get the number of user logical unit to check whether all
 	 * scsi_device finish initialization
 	 */
 	hpb_dev_info->num_lu = desc_buf[DEVICE_DESC_PARAM_NUM_LU];
+
+	if (hpb_dev_info->is_legacy)
+		return;
+
+	ret = ufshcd_query_attr_retry(hba, UPIU_QUERY_OPCODE_READ_ATTR,
+		QUERY_ATTR_IDN_MAX_HPB_SINGLE_CMD, 0, 0, &max_single_cmd);
+
+	if (ret)
+		hpb_dev_info->max_hpb_single_cmd = HPB_LEGACY_CHUNK_HIGH;
+	else
+		hpb_dev_info->max_hpb_single_cmd = min(max_single_cmd + 1, HPB_MULTI_CHUNK_HIGH);
 }
 
 void ufshpb_init(struct ufs_hba *hba)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/ufs/ufshpb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/ufs/ufshpb.h
@@ -31,7 +31,6 @@
 
 /* hpb support chunk size */
 #define HPB_LEGACY_CHUNK_HIGH			1
-#define HPB_MULTI_CHUNK_LOW			7
 #define HPB_MULTI_CHUNK_HIGH			255
 
 /* hpb vender defined opcode */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/vmw_pvscsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/vmw_pvscsi.c
@@ -586,9 +586,12 @@
 			 * Commands like INQUIRY may transfer less data than
 			 * requested by the initiator via bufflen. Set residual
 			 * count to make upper layer aware of the actual amount
-			 * of data returned.
+			 * of data returned. There are cases when controller
+			 * returns zero dataLen with non zero data - do not set
+			 * residual count in that case.
 			 */
-			scsi_set_resid(cmd, scsi_bufflen(cmd) - e->dataLen);
+			if (e->dataLen && (e->dataLen < scsi_bufflen(cmd)))
+				scsi_set_resid(cmd, scsi_bufflen(cmd) - e->dataLen);
 			cmd->result = (DID_OK << 16);
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/vmw_pvscsi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/vmw_pvscsi.h
@@ -331,8 +331,8 @@
 	u8	tag;
 	u8	bus;
 	u8	target;
-	u8	vcpuHint;
-	u8	unused[59];
+	u16	vcpuHint;
+	u8	unused[58];
 } __packed;
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/xen-scsifront.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/xen-scsifront.c
@@ -233,12 +233,11 @@
 		return;
 
 	for (i = 0; i < shadow->nr_grants; i++) {
-		if (unlikely(gnttab_query_foreign_access(shadow->gref[i]))) {
+		if (unlikely(!gnttab_try_end_foreign_access(shadow->gref[i]))) {
 			shost_printk(KERN_ALERT, info->host, KBUILD_MODNAME
 				     "grant still in use by backend\n");
 			BUG();
 		}
-		gnttab_end_foreign_access(shadow->gref[i], 0, 0UL);
 	}
 
 	kfree(shadow->sg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/scsi/zorro7xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/scsi/zorro7xx.c
@@ -159,6 +159,8 @@
 	scsi_remove_host(host);
 
 	NCR_700_release(host);
+	if (host->base > 0x01000000)
+		iounmap(hostdata->base);
 	kfree(hostdata);
 	free_irq(host->irq, host);
 	zorro_release_device(z);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/sh/clk/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/sh/clk/core.c
@@ -295,7 +295,7 @@
 	int ret;
 
 	if (!clk)
-		return -EINVAL;
+		return 0;
 
 	spin_lock_irqsave(&clock_lock, flags);
 	ret = __clk_enable(clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/sh/intc/chip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/sh/intc/chip.c
@@ -72,7 +72,7 @@
 	if (!cpumask_intersects(cpumask, cpu_online_mask))
 		return -1;
 
-	cpumask_copy(irq_data_get_affinity_mask(data), cpumask);
+	irq_data_update_affinity(data, cpumask);
 
 	return IRQ_SET_MASK_OK_NOCOPY;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/sh/intc/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/sh/intc/core.c
@@ -209,7 +209,6 @@
 		goto err0;
 
 	INIT_LIST_HEAD(&d->list);
-	list_add_tail(&d->list, &intc_list);
 
 	raw_spin_lock_init(&d->lock);
 	INIT_RADIX_TREE(&d->tree, GFP_ATOMIC);
@@ -369,6 +368,7 @@
 
 	d->skip_suspend = desc->skip_syscore_suspend;
 
+	list_add_tail(&d->list, &intc_list);
 	nr_intc_controllers++;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/sh/maple/maple.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/sh/maple/maple.c
@@ -834,8 +834,10 @@
 
 	maple_queue_cache = KMEM_CACHE(maple_buffer, SLAB_HWCACHE_ALIGN);
 
-	if (!maple_queue_cache)
+	if (!maple_queue_cache) {
+		retval = -ENOMEM;
 		goto cleanup_bothirqs;
+	}
 
 	INIT_LIST_HEAD(&maple_waitq);
 	INIT_LIST_HEAD(&maple_sentq);
@@ -848,6 +850,7 @@
 		if (!mdev[i]) {
 			while (i-- > 0)
 				maple_free_dev(mdev[i]);
+			retval = -ENOMEM;
 			goto cleanup_cache;
 		}
 		baseunits[i] = mdev[i];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/siox/siox-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/siox/siox-core.c
@@ -839,6 +839,8 @@
 
 err_device_register:
 	/* don't care to make the buffer smaller again */
+	put_device(&sdevice->dev);
+	sdevice = NULL;
 
 err_buf_alloc:
 	siox_master_unlock(smaster);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/slimbus/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/slimbus/Kconfig
@@ -22,7 +22,8 @@
 
 config SLIM_QCOM_NGD_CTRL
 	tristate "Qualcomm SLIMbus Satellite Non-Generic Device Component"
-	depends on HAS_IOMEM && DMA_ENGINE && NET && QCOM_RPROC_COMMON
+	depends on HAS_IOMEM && DMA_ENGINE && NET
+	depends on QCOM_RPROC_COMMON || (COMPILE_TEST && !QCOM_RPROC_COMMON)
 	depends on ARCH_QCOM || COMPILE_TEST
 	select QCOM_QMI_HELPERS
 	select QCOM_PDR_HELPERS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/slimbus/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/slimbus/core.c
@@ -436,8 +436,8 @@
 		if (ret < 0)
 			goto err;
 	} else if (report_present) {
-		ret = ida_simple_get(&ctrl->laddr_ida,
-				     0, SLIM_LA_MANAGER - 1, GFP_KERNEL);
+		ret = ida_alloc_max(&ctrl->laddr_ida,
+				    SLIM_LA_MANAGER - 1, GFP_KERNEL);
 		if (ret < 0)
 			goto err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/slimbus/messaging.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/slimbus/messaging.c
@@ -147,8 +147,9 @@
 	}
 
 	ret = ctrl->xfer_msg(ctrl, txn);
-
-	if (!ret && need_tid && !txn->msg->comp) {
+	if (ret == -ETIMEDOUT) {
+		slim_free_txn_tid(ctrl, txn);
+	} else if (!ret && need_tid && !txn->msg->comp) {
 		unsigned long ms = txn->rl + HZ;
 
 		timeout = wait_for_completion_timeout(txn->comp,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/slimbus/qcom-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/slimbus/qcom-ctrl.c
@@ -510,9 +510,9 @@
 	}
 
 	ctrl->irq = platform_get_irq(pdev, 0);
-	if (!ctrl->irq) {
+	if (ctrl->irq < 0) {
 		dev_err(&pdev->dev, "no slimbus IRQ\n");
-		return -ENODEV;
+		return ctrl->irq;
 	}
 
 	sctrl = &ctrl->ctrl;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/slimbus/qcom-ngd-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/slimbus/qcom-ngd-ctrl.c
@@ -1376,7 +1376,11 @@
 	ctrl = container_of(work, struct qcom_slim_ngd_ctrl, ngd_up_work);
 
 	/* Make sure qmi service is up before continuing */
-	wait_for_completion_interruptible(&ctrl->qmi_up);
+	if (!wait_for_completion_interruptible_timeout(&ctrl->qmi_up,
+						       msecs_to_jiffies(MSEC_PER_SEC))) {
+		dev_err(ctrl->dev, "QMI wait timeout\n");
+		return;
+	}
 
 	mutex_lock(&ctrl->ssr_lock);
 	qcom_slim_ngd_enable(ctrl, true);
@@ -1567,17 +1571,27 @@
 	ctrl->pdr = pdr_handle_alloc(slim_pd_status, ctrl);
 	if (IS_ERR(ctrl->pdr)) {
 		dev_err(dev, "Failed to init PDR handle\n");
-		return PTR_ERR(ctrl->pdr);
+		ret = PTR_ERR(ctrl->pdr);
+		goto err_pdr_alloc;
 	}
 
 	pds = pdr_add_lookup(ctrl->pdr, "avs/audio", "msm/adsp/audio_pd");
 	if (IS_ERR(pds) && PTR_ERR(pds) != -EALREADY) {
+		ret = PTR_ERR(pds);
 		dev_err(dev, "pdr add lookup failed: %d\n", ret);
-		return PTR_ERR(pds);
+		goto err_pdr_lookup;
 	}
 
 	platform_driver_register(&qcom_slim_ngd_driver);
 	return of_qcom_slim_ngd_register(dev, ctrl);
+
+err_pdr_alloc:
+	qcom_unregister_ssr_notifier(ctrl->notifier, &ctrl->nb);
+
+err_pdr_lookup:
+	pdr_handle_release(ctrl->pdr);
+
+	return ret;
 }
 
 static int qcom_slim_ngd_ctrl_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/slimbus/stream.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/slimbus/stream.c
@@ -67,10 +67,10 @@
 	384000,
 	768000,
 	0, /* Reserved */
-	110250,
-	220500,
-	441000,
-	882000,
+	11025,
+	22050,
+	44100,
+	88200,
 	176400,
 	352800,
 	705600,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/amlogic/meson-mx-socinfo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/amlogic/meson-mx-socinfo.c
@@ -126,6 +126,7 @@
 	np = of_find_matching_node(NULL, meson_mx_socinfo_analog_top_ids);
 	if (np) {
 		analog_top_regmap = syscon_node_to_regmap(np);
+		of_node_put(np);
 		if (IS_ERR(analog_top_regmap))
 			return PTR_ERR(analog_top_regmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/amlogic/meson-secure-pwrc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/amlogic/meson-secure-pwrc.c
@@ -104,7 +104,7 @@
 	SEC_PD(ACODEC,	0),
 	SEC_PD(AUDIO,	0),
 	SEC_PD(OTP,	0),
-	SEC_PD(DMA,	0),
+	SEC_PD(DMA,	GENPD_FLAG_ALWAYS_ON | GENPD_FLAG_IRQ_SAFE),
 	SEC_PD(SD_EMMC,	0),
 	SEC_PD(RAMA,	0),
 	/* SRAMB is used as ATF runtime memory, and should be always on */
@@ -139,8 +139,10 @@
 	}
 
 	pwrc = devm_kzalloc(&pdev->dev, sizeof(*pwrc), GFP_KERNEL);
-	if (!pwrc)
+	if (!pwrc) {
+		of_node_put(sm_np);
 		return -ENOMEM;
+	}
 
 	pwrc->fw = meson_sm_get(sm_np);
 	of_node_put(sm_np);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/aspeed/aspeed-lpc-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/aspeed/aspeed-lpc-ctrl.c
@@ -306,10 +306,9 @@
 	}
 
 	lpc_ctrl->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(lpc_ctrl->clk)) {
-		dev_err(dev, "couldn't get clock\n");
-		return PTR_ERR(lpc_ctrl->clk);
-	}
+	if (IS_ERR(lpc_ctrl->clk))
+		return dev_err_probe(dev, PTR_ERR(lpc_ctrl->clk),
+				     "couldn't get clock\n");
 	rc = clk_prepare_enable(lpc_ctrl->clk);
 	if (rc) {
 		dev_err(dev, "couldn't enable clock\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/aspeed/aspeed-socinfo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/aspeed/aspeed-socinfo.c
@@ -137,6 +137,7 @@
 
 	soc_dev = soc_device_register(attrs);
 	if (IS_ERR(soc_dev)) {
+		kfree(attrs->machine);
 		kfree(attrs->soc_id);
 		kfree(attrs->serial_number);
 		kfree(attrs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/atmel/soc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/atmel/soc.c
@@ -91,14 +91,14 @@
 	AT91_SOC(SAM9X60_CIDR_MATCH, AT91_CIDR_MATCH_MASK,
 		 AT91_CIDR_VERSION_MASK, SAM9X60_EXID_MATCH,
 		 "sam9x60", "sam9x60"),
-	AT91_SOC(SAM9X60_CIDR_MATCH, SAM9X60_D5M_EXID_MATCH,
-		 AT91_CIDR_VERSION_MASK, SAM9X60_EXID_MATCH,
+	AT91_SOC(SAM9X60_CIDR_MATCH, AT91_CIDR_MATCH_MASK,
+		 AT91_CIDR_VERSION_MASK, SAM9X60_D5M_EXID_MATCH,
 		 "sam9x60 64MiB DDR2 SiP", "sam9x60"),
-	AT91_SOC(SAM9X60_CIDR_MATCH, SAM9X60_D1G_EXID_MATCH,
-		 AT91_CIDR_VERSION_MASK, SAM9X60_EXID_MATCH,
+	AT91_SOC(SAM9X60_CIDR_MATCH, AT91_CIDR_MATCH_MASK,
+		 AT91_CIDR_VERSION_MASK, SAM9X60_D1G_EXID_MATCH,
 		 "sam9x60 128MiB DDR2 SiP", "sam9x60"),
-	AT91_SOC(SAM9X60_CIDR_MATCH, SAM9X60_D6K_EXID_MATCH,
-		 AT91_CIDR_VERSION_MASK, SAM9X60_EXID_MATCH,
+	AT91_SOC(SAM9X60_CIDR_MATCH, AT91_CIDR_MATCH_MASK,
+		 AT91_CIDR_VERSION_MASK, SAM9X60_D6K_EXID_MATCH,
 		 "sam9x60 8MiB SDRAM SiP", "sam9x60"),
 #endif
 #ifdef CONFIG_SOC_SAMA5
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/bcm/bcm63xx/bcm-pmb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/bcm/bcm63xx/bcm-pmb.c
@@ -314,6 +314,9 @@
 	for (e = table; e->name; e++) {
 		struct bcm_pmb_pm_domain *pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
 
+		if (!pd)
+			return -ENOMEM;
+
 		pd->pmb = pmb;
 		pd->data = e;
 		pd->genpd.name = e->name;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/bcm/brcmstb/pm/pm-arm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/bcm/brcmstb/pm/pm-arm.c
@@ -684,13 +684,14 @@
 	const struct of_device_id *of_id = NULL;
 	struct device_node *dn;
 	void __iomem *base;
-	int ret, i;
+	int ret, i, s;
 
 	/* AON ctrl registers */
 	base = brcmstb_ioremap_match(aon_ctrl_dt_ids, 0, NULL);
 	if (IS_ERR(base)) {
 		pr_err("error mapping AON_CTRL\n");
-		return PTR_ERR(base);
+		ret = PTR_ERR(base);
+		goto aon_err;
 	}
 	ctrl.aon_ctrl_base = base;
 
@@ -700,8 +701,10 @@
 		/* Assume standard offset */
 		ctrl.aon_sram = ctrl.aon_ctrl_base +
 				     AON_CTRL_SYSTEM_DATA_RAM_OFS;
+		s = 0;
 	} else {
 		ctrl.aon_sram = base;
+		s = 1;
 	}
 
 	writel_relaxed(0, ctrl.aon_sram + AON_REG_PANIC);
@@ -711,7 +714,8 @@
 				     (const void **)&ddr_phy_data);
 	if (IS_ERR(base)) {
 		pr_err("error mapping DDR PHY\n");
-		return PTR_ERR(base);
+		ret = PTR_ERR(base);
+		goto ddr_phy_err;
 	}
 	ctrl.support_warm_boot = ddr_phy_data->supports_warm_boot;
 	ctrl.pll_status_offset = ddr_phy_data->pll_status_offset;
@@ -731,17 +735,20 @@
 	for_each_matching_node(dn, ddr_shimphy_dt_ids) {
 		i = ctrl.num_memc;
 		if (i >= MAX_NUM_MEMC) {
+			of_node_put(dn);
 			pr_warn("too many MEMCs (max %d)\n", MAX_NUM_MEMC);
 			break;
 		}
 
 		base = of_io_request_and_map(dn, 0, dn->full_name);
 		if (IS_ERR(base)) {
+			of_node_put(dn);
 			if (!ctrl.support_warm_boot)
 				break;
 
 			pr_err("error mapping DDR SHIMPHY %d\n", i);
-			return PTR_ERR(base);
+			ret = PTR_ERR(base);
+			goto ddr_shimphy_err;
 		}
 		ctrl.memcs[i].ddr_shimphy_base = base;
 		ctrl.num_memc++;
@@ -752,14 +759,18 @@
 	for_each_matching_node(dn, brcmstb_memc_of_match) {
 		base = of_iomap(dn, 0);
 		if (!base) {
+			of_node_put(dn);
 			pr_err("error mapping DDR Sequencer %d\n", i);
-			return -ENOMEM;
+			ret = -ENOMEM;
+			goto brcmstb_memc_err;
 		}
 
 		of_id = of_match_node(brcmstb_memc_of_match, dn);
 		if (!of_id) {
 			iounmap(base);
-			return -EINVAL;
+			of_node_put(dn);
+			ret = -EINVAL;
+			goto brcmstb_memc_err;
 		}
 
 		ddr_seq_data = of_id->data;
@@ -779,20 +790,24 @@
 	dn = of_find_matching_node(NULL, sram_dt_ids);
 	if (!dn) {
 		pr_err("SRAM not found\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto brcmstb_memc_err;
 	}
 
 	ret = brcmstb_init_sram(dn);
+	of_node_put(dn);
 	if (ret) {
 		pr_err("error setting up SRAM for PM\n");
-		return ret;
+		goto brcmstb_memc_err;
 	}
 
 	ctrl.pdev = pdev;
 
 	ctrl.s3_params = kmalloc(sizeof(*ctrl.s3_params), GFP_KERNEL);
-	if (!ctrl.s3_params)
-		return -ENOMEM;
+	if (!ctrl.s3_params) {
+		ret = -ENOMEM;
+		goto s3_params_err;
+	}
 	ctrl.s3_params_pa = dma_map_single(&pdev->dev, ctrl.s3_params,
 					   sizeof(*ctrl.s3_params),
 					   DMA_TO_DEVICE);
@@ -812,7 +827,21 @@
 
 out:
 	kfree(ctrl.s3_params);
-
+s3_params_err:
+	iounmap(ctrl.boot_sram);
+brcmstb_memc_err:
+	for (i--; i >= 0; i--)
+		iounmap(ctrl.memcs[i].ddr_ctrl);
+ddr_shimphy_err:
+	for (i = 0; i < ctrl.num_memc; i++)
+		iounmap(ctrl.memcs[i].ddr_shimphy_base);
+
+	iounmap(ctrl.memcs[0].ddr_phy_base);
+ddr_phy_err:
+	iounmap(ctrl.aon_ctrl_base);
+	if (s)
+		iounmap(ctrl.aon_sram);
+aon_err:
 	pr_warn("PM: initialization failed with code %d\n", ret);
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/Kconfig
@@ -24,6 +24,7 @@
         tristate "QorIQ DPAA2 DPIO driver"
         depends on FSL_MC_BUS
         select SOC_BUS
+        select FSL_GUTS
         help
 	  Driver for the DPAA2 DPIO object.  A DPIO provides queue and
 	  buffer management facilities for software to interact with
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/dpaa2-console.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/dpaa2-console.c
@@ -231,6 +231,7 @@
 	cd->cur_ptr += bytes;
 	written += bytes;
 
+	kfree(kbuf);
 	return written;
 
 err_free_buf:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/dpio/dpio-service.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/dpio/dpio-service.c
@@ -59,7 +59,7 @@
 	 * potentially being migrated away.
 	 */
 	if (cpu < 0)
-		cpu = smp_processor_id();
+		cpu = raw_smp_processor_id();
 
 	/* If a specific cpu was requested, pick it up immediately */
 	return dpio_by_cpu[cpu];
@@ -485,7 +485,7 @@
 	struct qbman_eq_desc *ed;
 	int i, ret;
 
-	ed = kcalloc(sizeof(struct qbman_eq_desc), 32, GFP_KERNEL);
+	ed = kcalloc(32, sizeof(struct qbman_eq_desc), GFP_KERNEL);
 	if (!ed)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/dpio/qbman-portal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/dpio/qbman-portal.c
@@ -732,8 +732,7 @@
 	int i, num_enqueued = 0;
 	unsigned long irq_flags;
 
-	spin_lock(&s->access_spinlock);
-	local_irq_save(irq_flags);
+	spin_lock_irqsave(&s->access_spinlock, irq_flags);
 
 	half_mask = (s->eqcr.pi_ci_mask>>1);
 	full_mask = s->eqcr.pi_ci_mask;
@@ -744,8 +743,7 @@
 		s->eqcr.available = qm_cyc_diff(s->eqcr.pi_ring_size,
 					eqcr_ci, s->eqcr.ci);
 		if (!s->eqcr.available) {
-			local_irq_restore(irq_flags);
-			spin_unlock(&s->access_spinlock);
+			spin_unlock_irqrestore(&s->access_spinlock, irq_flags);
 			return 0;
 		}
 	}
@@ -784,8 +782,7 @@
 	dma_wmb();
 	qbman_write_register(s, QBMAN_CINH_SWP_EQCR_PI,
 				(QB_RT_BIT)|(s->eqcr.pi)|s->eqcr.pi_vb);
-	local_irq_restore(irq_flags);
-	spin_unlock(&s->access_spinlock);
+	spin_unlock_irqrestore(&s->access_spinlock, irq_flags);
 
 	return num_enqueued;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/guts.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/guts.c
@@ -28,7 +28,6 @@
 static struct guts *guts;
 static struct soc_device_attribute soc_dev_attr;
 static struct soc_device *soc_dev;
-static struct device_node *root;
 
 
 /* SoC die attribute definition for QorIQ platform */
@@ -138,11 +137,11 @@
 
 static int fsl_guts_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
+	struct device_node *root, *np = pdev->dev.of_node;
 	struct device *dev = &pdev->dev;
 	struct resource *res;
 	const struct fsl_soc_die_attr *soc_die;
-	const char *machine;
+	const char *machine = NULL;
 	u32 svr;
 
 	/* Initialize guts */
@@ -161,8 +160,14 @@
 	root = of_find_node_by_path("/");
 	if (of_property_read_string(root, "model", &machine))
 		of_property_read_string_index(root, "compatible", 0, &machine);
-	if (machine)
-		soc_dev_attr.machine = machine;
+	if (machine) {
+		soc_dev_attr.machine = devm_kstrdup(dev, machine, GFP_KERNEL);
+		if (!soc_dev_attr.machine) {
+			of_node_put(root);
+			return -ENOMEM;
+		}
+	}
+	of_node_put(root);
 
 	svr = fsl_guts_get_svr();
 	soc_die = fsl_soc_die_match(svr, fsl_soc_die);
@@ -197,7 +202,6 @@
 static int fsl_guts_remove(struct platform_device *dev)
 {
 	soc_device_unregister(soc_dev);
-	of_node_put(root);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/qbman/qman.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/qbman/qman.c
@@ -991,7 +991,7 @@
 	/* linked-list of CSCN handlers. */
 	struct list_head cgr_cbs;
 	/* list lock */
-	spinlock_t cgr_lock;
+	raw_spinlock_t cgr_lock;
 	struct work_struct congestion_work;
 	struct work_struct mr_work;
 	char irqname[MAX_IRQNAME];
@@ -1281,7 +1281,7 @@
 		/* if the given mask is NULL, assume all CGRs can be seen */
 		qman_cgrs_fill(&portal->cgrs[0]);
 	INIT_LIST_HEAD(&portal->cgr_cbs);
-	spin_lock_init(&portal->cgr_lock);
+	raw_spin_lock_init(&portal->cgr_lock);
 	INIT_WORK(&portal->congestion_work, qm_congestion_task);
 	INIT_WORK(&portal->mr_work, qm_mr_process_task);
 	portal->bits = 0;
@@ -1456,11 +1456,14 @@
 	union qm_mc_result *mcr;
 	struct qman_cgr *cgr;
 
-	spin_lock(&p->cgr_lock);
+	/*
+	 * FIXME: QM_MCR_TIMEOUT is 10ms, which is too long for a raw spinlock!
+	 */
+	raw_spin_lock_irq(&p->cgr_lock);
 	qm_mc_start(&p->p);
 	qm_mc_commit(&p->p, QM_MCC_VERB_QUERYCONGESTION);
 	if (!qm_mc_result_timeout(&p->p, &mcr)) {
-		spin_unlock(&p->cgr_lock);
+		raw_spin_unlock_irq(&p->cgr_lock);
 		dev_crit(p->config->dev, "QUERYCONGESTION timeout\n");
 		qman_p_irqsource_add(p, QM_PIRQ_CSCI);
 		return;
@@ -1476,7 +1479,7 @@
 	list_for_each_entry(cgr, &p->cgr_cbs, node)
 		if (cgr->cb && qman_cgrs_get(&c, cgr->cgrid))
 			cgr->cb(p, cgr, qman_cgrs_get(&rr, cgr->cgrid));
-	spin_unlock(&p->cgr_lock);
+	raw_spin_unlock_irq(&p->cgr_lock);
 	qman_p_irqsource_add(p, QM_PIRQ_CSCI);
 }
 
@@ -2440,7 +2443,7 @@
 	preempt_enable();
 
 	cgr->chan = p->config->channel;
-	spin_lock(&p->cgr_lock);
+	raw_spin_lock_irq(&p->cgr_lock);
 
 	if (opts) {
 		struct qm_mcc_initcgr local_opts = *opts;
@@ -2477,19 +2480,14 @@
 	    qman_cgrs_get(&p->cgrs[1], cgr->cgrid))
 		cgr->cb(p, cgr, 1);
 out:
-	spin_unlock(&p->cgr_lock);
+	raw_spin_unlock_irq(&p->cgr_lock);
 	put_affine_portal();
 	return ret;
 }
 EXPORT_SYMBOL(qman_create_cgr);
 
-int qman_delete_cgr(struct qman_cgr *cgr)
+static struct qman_portal *qman_cgr_get_affine_portal(struct qman_cgr *cgr)
 {
-	unsigned long irqflags;
-	struct qm_mcr_querycgr cgr_state;
-	struct qm_mcc_initcgr local_opts;
-	int ret = 0;
-	struct qman_cgr *i;
 	struct qman_portal *p = get_affine_portal();
 
 	if (cgr->chan != p->config->channel) {
@@ -2497,12 +2495,27 @@
 		dev_err(p->config->dev, "CGR not owned by current portal");
 		dev_dbg(p->config->dev, " create 0x%x, delete 0x%x\n",
 			cgr->chan, p->config->channel);
-
-		ret = -EINVAL;
-		goto put_portal;
+		put_affine_portal();
+		return NULL;
 	}
+
+	return p;
+}
+
+int qman_delete_cgr(struct qman_cgr *cgr)
+{
+	unsigned long irqflags;
+	struct qm_mcr_querycgr cgr_state;
+	struct qm_mcc_initcgr local_opts;
+	int ret = 0;
+	struct qman_cgr *i;
+	struct qman_portal *p = qman_cgr_get_affine_portal(cgr);
+
+	if (!p)
+		return -EINVAL;
+
 	memset(&local_opts, 0, sizeof(struct qm_mcc_initcgr));
-	spin_lock_irqsave(&p->cgr_lock, irqflags);
+	raw_spin_lock_irqsave(&p->cgr_lock, irqflags);
 	list_del(&cgr->node);
 	/*
 	 * If there are no other CGR objects for this CGRID in the list,
@@ -2527,8 +2540,7 @@
 		/* add back to the list */
 		list_add(&cgr->node, &p->cgr_cbs);
 release_lock:
-	spin_unlock_irqrestore(&p->cgr_lock, irqflags);
-put_portal:
+	raw_spin_unlock_irqrestore(&p->cgr_lock, irqflags);
 	put_affine_portal();
 	return ret;
 }
@@ -2559,6 +2571,54 @@
 }
 EXPORT_SYMBOL(qman_delete_cgr_safe);
 
+static int qman_update_cgr(struct qman_cgr *cgr, struct qm_mcc_initcgr *opts)
+{
+	int ret;
+	unsigned long irqflags;
+	struct qman_portal *p = qman_cgr_get_affine_portal(cgr);
+
+	if (!p)
+		return -EINVAL;
+
+	raw_spin_lock_irqsave(&p->cgr_lock, irqflags);
+	ret = qm_modify_cgr(cgr, 0, opts);
+	raw_spin_unlock_irqrestore(&p->cgr_lock, irqflags);
+	put_affine_portal();
+	return ret;
+}
+
+struct update_cgr_params {
+	struct qman_cgr *cgr;
+	struct qm_mcc_initcgr *opts;
+	int ret;
+};
+
+static void qman_update_cgr_smp_call(void *p)
+{
+	struct update_cgr_params *params = p;
+
+	params->ret = qman_update_cgr(params->cgr, params->opts);
+}
+
+int qman_update_cgr_safe(struct qman_cgr *cgr, struct qm_mcc_initcgr *opts)
+{
+	struct update_cgr_params params = {
+		.cgr = cgr,
+		.opts = opts,
+	};
+
+	preempt_disable();
+	if (qman_cgr_cpus[cgr->cgrid] != smp_processor_id())
+		smp_call_function_single(qman_cgr_cpus[cgr->cgrid],
+					 qman_update_cgr_smp_call, &params,
+					 true);
+	else
+		params.ret = qman_update_cgr(cgr, opts);
+	preempt_enable();
+	return params.ret;
+}
+EXPORT_SYMBOL(qman_update_cgr_safe);
+
 /* Cleanup FQs */
 
 static int _qm_mr_consume_and_match_verb(struct qm_portal *p, int v)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/qe/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/qe/Kconfig
@@ -39,6 +39,7 @@
 
 config QE_USB
 	bool
+	depends on QUICC_ENGINE
 	default y if USB_FSL_QE
 	help
 	  QE USB Controller support
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/qe/qe_io.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/qe/qe_io.c
@@ -35,6 +35,8 @@
 	if (ret)
 		return ret;
 	par_io = ioremap(res.start, resource_size(&res));
+	if (!par_io)
+		return -ENOMEM;
 
 	if (!of_property_read_u32(np, "num-ports", &num_ports))
 		num_par_io_ports = num_ports;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/fsl/rcpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/fsl/rcpm.c
@@ -36,6 +36,7 @@
 		return;
 
 	regs = of_iomap(np, 0);
+	of_node_put(np);
 	if (!regs)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/imx/gpcv2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/imx/gpcv2.c
@@ -237,6 +237,8 @@
 		}
 	}
 
+	reset_control_assert(domain->reset);
+
 	/* Enable reset clocks for all devices in the domain */
 	ret = clk_bulk_prepare_enable(domain->num_clks, domain->clks);
 	if (ret) {
@@ -244,6 +246,9 @@
 		goto out_regulator_disable;
 	}
 
+	/* delays for reset to propagate */
+	udelay(5);
+
 	if (domain->bits.pxx) {
 		/* request the domain to power up */
 		regmap_update_bits(domain->regmap, GPC_PU_PGC_SW_PUP_REQ,
@@ -266,8 +271,6 @@
 				  GPC_PGC_CTRL_PCR);
 	}
 
-	reset_control_assert(domain->reset);
-
 	/* delay for reset to propagate */
 	udelay(5);
 
@@ -369,7 +372,7 @@
 		}
 	}
 
-	pm_runtime_put(domain->dev);
+	pm_runtime_put_sync_suspend(domain->dev);
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/imx/soc-imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/imx/soc-imx.c
@@ -36,6 +36,10 @@
 	int ret;
 	int i;
 
+	/* Return early if this is running on devices with different SoCs */
+	if (!__mxc_cpu_type)
+		return 0;
+
 	if (of_machine_is_compatible("fsl,ls1021a"))
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/imx/soc-imx8m.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/imx/soc-imx8m.c
@@ -11,6 +11,7 @@
 #include <linux/platform_device.h>
 #include <linux/arm-smccc.h>
 #include <linux/of.h>
+#include <linux/clk.h>
 
 #define REV_B1				0x21
 
@@ -29,7 +30,7 @@
 
 struct imx8_soc_data {
 	char *name;
-	u32 (*soc_revision)(void);
+	int (*soc_revision)(u32 *socrev);
 };
 
 static u64 soc_uid;
@@ -50,19 +51,32 @@
 static inline u32 imx8mq_soc_revision_from_atf(void) { return 0; };
 #endif
 
-static u32 __init imx8mq_soc_revision(void)
+static int imx8mq_soc_revision(u32 *socrev)
 {
 	struct device_node *np;
 	void __iomem *ocotp_base;
 	u32 magic;
 	u32 rev;
+	struct clk *clk;
+	int ret;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mq-ocotp");
 	if (!np)
-		return 0;
+		return -EINVAL;
 
 	ocotp_base = of_iomap(np, 0);
-	WARN_ON(!ocotp_base);
+	if (!ocotp_base) {
+		ret = -EINVAL;
+		goto err_iomap;
+	}
+
+	clk = of_clk_get_by_name(np, NULL);
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		goto err_clk;
+	}
+
+	clk_prepare_enable(clk);
 
 	/*
 	 * SOC revision on older imx8mq is not available in fuses so query
@@ -79,55 +93,90 @@
 	soc_uid <<= 32;
 	soc_uid |= readl_relaxed(ocotp_base + OCOTP_UID_LOW);
 
+	*socrev = rev;
+
+	clk_disable_unprepare(clk);
+	clk_put(clk);
 	iounmap(ocotp_base);
 	of_node_put(np);
 
-	return rev;
+	return 0;
+
+err_clk:
+	iounmap(ocotp_base);
+err_iomap:
+	of_node_put(np);
+	return ret;
 }
 
-static void __init imx8mm_soc_uid(void)
+static int imx8mm_soc_uid(void)
 {
 	void __iomem *ocotp_base;
 	struct device_node *np;
+	struct clk *clk;
+	int ret = 0;
 	u32 offset = of_machine_is_compatible("fsl,imx8mp") ?
 		     IMX8MP_OCOTP_UID_OFFSET : 0;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mm-ocotp");
 	if (!np)
-		return;
+		return -EINVAL;
 
 	ocotp_base = of_iomap(np, 0);
-	WARN_ON(!ocotp_base);
+	if (!ocotp_base) {
+		ret = -EINVAL;
+		goto err_iomap;
+	}
+
+	clk = of_clk_get_by_name(np, NULL);
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		goto err_clk;
+	}
+
+	clk_prepare_enable(clk);
 
 	soc_uid = readl_relaxed(ocotp_base + OCOTP_UID_HIGH + offset);
 	soc_uid <<= 32;
 	soc_uid |= readl_relaxed(ocotp_base + OCOTP_UID_LOW + offset);
 
+	clk_disable_unprepare(clk);
+	clk_put(clk);
+
+err_clk:
 	iounmap(ocotp_base);
+err_iomap:
 	of_node_put(np);
+
+	return ret;
 }
 
-static u32 __init imx8mm_soc_revision(void)
+static int imx8mm_soc_revision(u32 *socrev)
 {
 	struct device_node *np;
 	void __iomem *anatop_base;
-	u32 rev;
+	int ret;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mm-anatop");
 	if (!np)
-		return 0;
+		return -EINVAL;
 
 	anatop_base = of_iomap(np, 0);
-	WARN_ON(!anatop_base);
+	if (!anatop_base) {
+		ret = -EINVAL;
+		goto err_iomap;
+	}
 
-	rev = readl_relaxed(anatop_base + ANADIG_DIGPROG_IMX8MM);
+	*socrev = readl_relaxed(anatop_base + ANADIG_DIGPROG_IMX8MM);
 
 	iounmap(anatop_base);
 	of_node_put(np);
 
-	imx8mm_soc_uid();
+	return imx8mm_soc_uid();
 
-	return rev;
+err_iomap:
+	of_node_put(np);
+	return ret;
 }
 
 static const struct imx8_soc_data imx8mq_soc_data = {
@@ -163,7 +212,7 @@
 	kasprintf(GFP_KERNEL, "%d.%d", (soc_rev >> 4) & 0xf,  soc_rev & 0xf) : \
 	"unknown"
 
-static int __init imx8_soc_init(void)
+static int imx8m_soc_probe(struct platform_device *pdev)
 {
 	struct soc_device_attribute *soc_dev_attr;
 	struct soc_device *soc_dev;
@@ -191,8 +240,11 @@
 	data = id->data;
 	if (data) {
 		soc_dev_attr->soc_id = data->name;
-		if (data->soc_revision)
-			soc_rev = data->soc_revision();
+		if (data->soc_revision) {
+			ret = data->soc_revision(&soc_rev);
+			if (ret)
+				goto free_soc;
+		}
 	}
 
 	soc_dev_attr->revision = imx8_revision(soc_rev);
@@ -230,4 +282,36 @@
 	kfree(soc_dev_attr);
 	return ret;
 }
+
+static struct platform_driver imx8m_soc_driver = {
+	.probe = imx8m_soc_probe,
+	.driver = {
+		.name = "imx8m-soc",
+	},
+};
+
+static int __init imx8_soc_init(void)
+{
+	struct platform_device *pdev;
+	int ret;
+
+	/* No match means this is non-i.MX8M hardware, do nothing. */
+	if (!of_match_node(imx8_soc_match, of_root))
+		return 0;
+
+	ret = platform_driver_register(&imx8m_soc_driver);
+	if (ret) {
+		pr_err("Failed to register imx8m-soc platform driver: %d\n", ret);
+		return ret;
+	}
+
+	pdev = platform_device_register_simple("imx8m-soc", -1, NULL, 0);
+	if (IS_ERR(pdev)) {
+		pr_err("Failed to register imx8m-soc platform device: %ld\n", PTR_ERR(pdev));
+		platform_driver_unregister(&imx8m_soc_driver);
+		return PTR_ERR(pdev);
+	}
+
+	return 0;
+}
 device_initcall(imx8_soc_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ixp4xx/ixp4xx-npe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ixp4xx/ixp4xx-npe.c
@@ -743,7 +743,7 @@
 static struct platform_driver ixp4xx_npe_driver = {
 	.driver = {
 		.name           = "ixp4xx-npe",
-		.of_match_table = of_match_ptr(ixp4xx_npe_of_match),
+		.of_match_table = ixp4xx_npe_of_match,
 	},
 	.probe = ixp4xx_npe_probe,
 	.remove = ixp4xx_npe_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/mediatek/mtk-cmdq-helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/mediatek/mtk-cmdq-helper.c
@@ -13,7 +13,8 @@
 #define CMDQ_POLL_ENABLE_MASK	BIT(0)
 #define CMDQ_EOC_IRQ_EN		BIT(0)
 #define CMDQ_REG_TYPE		1
-#define CMDQ_JUMP_RELATIVE	1
+#define CMDQ_JUMP_RELATIVE	0
+#define CMDQ_JUMP_ABSOLUTE	1
 
 struct cmdq_instruction {
 	union {
@@ -396,7 +397,7 @@
 	struct cmdq_instruction inst = {};
 
 	inst.op = CMDQ_CODE_JUMP;
-	inst.offset = CMDQ_JUMP_RELATIVE;
+	inst.offset = CMDQ_JUMP_ABSOLUTE;
 	inst.value = addr >>
 		cmdq_get_shift_pa(((struct cmdq_client *)pkt->cl)->chan);
 	return cmdq_pkt_append_command(pkt, inst);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/mediatek/mtk-devapc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/mediatek/mtk-devapc.c
@@ -258,44 +258,44 @@
 		return -EINVAL;
 
 	devapc_irq = irq_of_parse_and_map(node, 0);
-	if (!devapc_irq)
-		return -EINVAL;
-
-	ctx->infra_clk = devm_clk_get(&pdev->dev, "devapc-infra-clock");
-	if (IS_ERR(ctx->infra_clk))
-		return -EINVAL;
+	if (!devapc_irq) {
+		ret = -EINVAL;
+		goto err;
+	}
 
-	if (clk_prepare_enable(ctx->infra_clk))
-		return -EINVAL;
+	ctx->infra_clk = devm_clk_get_enabled(&pdev->dev, "devapc-infra-clock");
+	if (IS_ERR(ctx->infra_clk)) {
+		ret = -EINVAL;
+		goto err;
+	}
 
 	ret = devm_request_irq(&pdev->dev, devapc_irq, devapc_violation_irq,
 			       IRQF_TRIGGER_NONE, "devapc", ctx);
-	if (ret) {
-		clk_disable_unprepare(ctx->infra_clk);
-		return ret;
-	}
+	if (ret)
+		goto err;
 
 	platform_set_drvdata(pdev, ctx);
 
 	start_devapc(ctx);
 
 	return 0;
+
+err:
+	iounmap(ctx->infra_base);
+	return ret;
 }
 
-static int mtk_devapc_remove(struct platform_device *pdev)
+static void mtk_devapc_remove(struct platform_device *pdev)
 {
 	struct mtk_devapc_context *ctx = platform_get_drvdata(pdev);
 
 	stop_devapc(ctx);
-
-	clk_disable_unprepare(ctx->infra_clk);
-
-	return 0;
+	iounmap(ctx->infra_base);
 }
 
 static struct platform_driver mtk_devapc_driver = {
 	.probe = mtk_devapc_probe,
-	.remove = mtk_devapc_remove,
+	.remove_new = mtk_devapc_remove,
 	.driver = {
 		.name = "mtk-devapc",
 		.of_match_table = mtk_devapc_dt_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/mediatek/mtk-pm-domains.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/mediatek/mtk-pm-domains.c
@@ -272,9 +272,9 @@
 	clk_bulk_disable_unprepare(pd->num_subsys_clks, pd->subsys_clks);
 
 	/* subsys power off */
-	regmap_clear_bits(scpsys->base, pd->data->ctl_offs, PWR_RST_B_BIT);
 	regmap_set_bits(scpsys->base, pd->data->ctl_offs, PWR_ISO_BIT);
 	regmap_set_bits(scpsys->base, pd->data->ctl_offs, PWR_CLK_DIS_BIT);
+	regmap_clear_bits(scpsys->base, pd->data->ctl_offs, PWR_RST_B_BIT);
 	regmap_clear_bits(scpsys->base, pd->data->ctl_offs, PWR_ON_2ND_BIT);
 	regmap_clear_bits(scpsys->base, pd->data->ctl_offs, PWR_ON_BIT);
 
@@ -443,6 +443,9 @@
 	pd->genpd.power_off = scpsys_power_off;
 	pd->genpd.power_on = scpsys_power_on;
 
+	if (MTK_SCPD_CAPS(pd, MTK_SCPD_ACTIVE_WAKEUP))
+		pd->genpd.flags |= GENPD_FLAG_ACTIVE_WAKEUP;
+
 	if (MTK_SCPD_CAPS(pd, MTK_SCPD_KEEP_DEFAULT_OFF))
 		pm_genpd_init(&pd->genpd, NULL, true);
 	else
@@ -490,6 +493,11 @@
 			goto err_put_node;
 		}
 
+		/* recursive call to add all subdomains */
+		ret = scpsys_add_subdomain(scpsys, child);
+		if (ret)
+			goto err_put_node;
+
 		ret = pm_genpd_add_subdomain(parent_pd, child_pd);
 		if (ret) {
 			dev_err(scpsys->dev, "failed to add %s subdomain to parent %s\n",
@@ -499,11 +507,6 @@
 			dev_dbg(scpsys->dev, "%s add subdomain: %s\n", parent_pd->name,
 				child_pd->name);
 		}
-
-		/* recursive call to add all subdomains */
-		ret = scpsys_add_subdomain(scpsys, child);
-		if (ret)
-			goto err_put_node;
 	}
 
 	return 0;
@@ -517,9 +520,6 @@
 {
 	int ret;
 
-	if (scpsys_domain_is_on(pd))
-		scpsys_power_off(&pd->genpd);
-
 	/*
 	 * We're in the error cleanup already, so we only complain,
 	 * but won't emit another error on top of the original one.
@@ -529,6 +529,8 @@
 		dev_err(pd->scpsys->dev,
 			"failed to remove domain '%s' : %d - state may be inconsistent\n",
 			pd->genpd.name, ret);
+	if (scpsys_domain_is_on(pd))
+		scpsys_power_off(&pd->genpd);
 
 	clk_bulk_put(pd->num_clks, pd->clks);
 	clk_bulk_put(pd->num_subsys_clks, pd->subsys_clks);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/Kconfig
@@ -63,6 +63,7 @@
 config QCOM_LLCC
 	tristate "Qualcomm Technologies, Inc. LLCC driver"
 	depends on ARCH_QCOM || COMPILE_TEST
+	select REGMAP_MMIO
 	help
 	  Qualcomm Technologies, Inc. platform specific
 	  Last Level Cache Controller(LLCC) driver for platforms such as,
@@ -129,6 +130,7 @@
 
 config QCOM_RPMPD
 	tristate "Qualcomm RPM Power domain driver"
+	depends on PM
 	depends on QCOM_SMD_RPM
 	help
 	  QCOM RPM Power domain driver to support power-domains with
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/apr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/apr.c
@@ -15,13 +15,18 @@
 #include <linux/rpmsg.h>
 #include <linux/of.h>
 
-struct apr {
+enum {
+	PR_TYPE_APR = 0,
+};
+
+struct packet_router {
 	struct rpmsg_endpoint *ch;
 	struct device *dev;
 	spinlock_t svcs_lock;
 	spinlock_t rx_lock;
 	struct idr svcs_idr;
 	int dest_domain_id;
+	int type;
 	struct pdr_handle *pdr;
 	struct workqueue_struct *rxwq;
 	struct work_struct rx_work;
@@ -44,21 +49,21 @@
  */
 int apr_send_pkt(struct apr_device *adev, struct apr_pkt *pkt)
 {
-	struct apr *apr = dev_get_drvdata(adev->dev.parent);
+	struct packet_router *apr = dev_get_drvdata(adev->dev.parent);
 	struct apr_hdr *hdr;
 	unsigned long flags;
 	int ret;
 
-	spin_lock_irqsave(&adev->lock, flags);
+	spin_lock_irqsave(&adev->svc.lock, flags);
 
 	hdr = &pkt->hdr;
 	hdr->src_domain = APR_DOMAIN_APPS;
-	hdr->src_svc = adev->svc_id;
+	hdr->src_svc = adev->svc.id;
 	hdr->dest_domain = adev->domain_id;
-	hdr->dest_svc = adev->svc_id;
+	hdr->dest_svc = adev->svc.id;
 
 	ret = rpmsg_trysend(apr->ch, pkt, hdr->pkt_size);
-	spin_unlock_irqrestore(&adev->lock, flags);
+	spin_unlock_irqrestore(&adev->svc.lock, flags);
 
 	return ret ? ret : hdr->pkt_size;
 }
@@ -74,7 +79,7 @@
 static int apr_callback(struct rpmsg_device *rpdev, void *buf,
 				  int len, void *priv, u32 addr)
 {
-	struct apr *apr = dev_get_drvdata(&rpdev->dev);
+	struct packet_router *apr = dev_get_drvdata(&rpdev->dev);
 	struct apr_rx_buf *abuf;
 	unsigned long flags;
 
@@ -100,11 +105,11 @@
 	return 0;
 }
 
-
-static int apr_do_rx_callback(struct apr *apr, struct apr_rx_buf *abuf)
+static int apr_do_rx_callback(struct packet_router *apr, struct apr_rx_buf *abuf)
 {
 	uint16_t hdr_size, msg_type, ver, svc_id;
-	struct apr_device *svc = NULL;
+	struct pkt_router_svc *svc;
+	struct apr_device *adev;
 	struct apr_driver *adrv = NULL;
 	struct apr_resp_pkt resp;
 	struct apr_hdr *hdr;
@@ -145,12 +150,15 @@
 	svc_id = hdr->dest_svc;
 	spin_lock_irqsave(&apr->svcs_lock, flags);
 	svc = idr_find(&apr->svcs_idr, svc_id);
-	if (svc && svc->dev.driver)
-		adrv = to_apr_driver(svc->dev.driver);
+	if (svc && svc->dev->driver) {
+		adev = svc_to_apr_device(svc);
+		adrv = to_apr_driver(adev->dev.driver);
+	}
 	spin_unlock_irqrestore(&apr->svcs_lock, flags);
 
-	if (!adrv) {
-		dev_err(apr->dev, "APR: service is not registered\n");
+	if (!adrv || !adev) {
+		dev_err(apr->dev, "APR: service is not registered (%d)\n",
+			svc_id);
 		return -EINVAL;
 	}
 
@@ -164,20 +172,26 @@
 	if (resp.payload_size > 0)
 		resp.payload = buf + hdr_size;
 
-	adrv->callback(svc, &resp);
+	adrv->callback(adev, &resp);
 
 	return 0;
 }
 
 static void apr_rxwq(struct work_struct *work)
 {
-	struct apr *apr = container_of(work, struct apr, rx_work);
+	struct packet_router *apr = container_of(work, struct packet_router, rx_work);
 	struct apr_rx_buf *abuf, *b;
 	unsigned long flags;
 
 	if (!list_empty(&apr->rx_list)) {
 		list_for_each_entry_safe(abuf, b, &apr->rx_list, node) {
-			apr_do_rx_callback(apr, abuf);
+			switch (apr->type) {
+			case PR_TYPE_APR:
+				apr_do_rx_callback(apr, abuf);
+				break;
+			default:
+				break;
+			}
 			spin_lock_irqsave(&apr->rx_lock, flags);
 			list_del(&abuf->node);
 			spin_unlock_irqrestore(&apr->rx_lock, flags);
@@ -201,7 +215,7 @@
 
 	while (id->domain_id != 0 || id->svc_id != 0) {
 		if (id->domain_id == adev->domain_id &&
-		    id->svc_id == adev->svc_id)
+		    id->svc_id == adev->svc.id)
 			return 1;
 		id++;
 	}
@@ -221,14 +235,14 @@
 {
 	struct apr_device *adev = to_apr_device(dev);
 	struct apr_driver *adrv;
-	struct apr *apr = dev_get_drvdata(adev->dev.parent);
+	struct packet_router *apr = dev_get_drvdata(adev->dev.parent);
 
 	if (dev->driver) {
 		adrv = to_apr_driver(dev->driver);
 		if (adrv->remove)
 			adrv->remove(adev);
 		spin_lock(&apr->svcs_lock);
-		idr_remove(&apr->svcs_idr, adev->svc_id);
+		idr_remove(&apr->svcs_idr, adev->svc.id);
 		spin_unlock(&apr->svcs_lock);
 	}
 }
@@ -255,28 +269,39 @@
 EXPORT_SYMBOL_GPL(aprbus);
 
 static int apr_add_device(struct device *dev, struct device_node *np,
-			  const struct apr_device_id *id)
+			  u32 svc_id, u32 domain_id)
 {
-	struct apr *apr = dev_get_drvdata(dev);
+	struct packet_router *apr = dev_get_drvdata(dev);
 	struct apr_device *adev = NULL;
+	struct pkt_router_svc *svc;
 	int ret;
 
 	adev = kzalloc(sizeof(*adev), GFP_KERNEL);
 	if (!adev)
 		return -ENOMEM;
 
-	spin_lock_init(&adev->lock);
+	adev->svc_id = svc_id;
+	svc = &adev->svc;
+
+	svc->id = svc_id;
+	svc->pr = apr;
+	svc->priv = adev;
+	svc->dev = dev;
+	spin_lock_init(&svc->lock);
+
+	adev->domain_id = domain_id;
 
-	adev->svc_id = id->svc_id;
-	adev->domain_id = id->domain_id;
-	adev->version = id->svc_version;
 	if (np)
 		snprintf(adev->name, APR_NAME_SIZE, "%pOFn", np);
-	else
-		strscpy(adev->name, id->name, APR_NAME_SIZE);
 
-	dev_set_name(&adev->dev, "aprsvc:%s:%x:%x", adev->name,
-		     id->domain_id, id->svc_id);
+	switch (apr->type) {
+	case PR_TYPE_APR:
+		dev_set_name(&adev->dev, "aprsvc:%s:%x:%x", adev->name,
+			     domain_id, svc_id);
+		break;
+	default:
+		break;
+	}
 
 	adev->dev.bus = &aprbus;
 	adev->dev.parent = dev;
@@ -285,12 +310,20 @@
 	adev->dev.driver = NULL;
 
 	spin_lock(&apr->svcs_lock);
-	idr_alloc(&apr->svcs_idr, adev, id->svc_id,
-		  id->svc_id + 1, GFP_ATOMIC);
+	ret = idr_alloc(&apr->svcs_idr, svc, svc_id, svc_id + 1, GFP_ATOMIC);
 	spin_unlock(&apr->svcs_lock);
+	if (ret < 0) {
+		dev_err(dev, "idr_alloc failed: %d\n", ret);
+		goto out;
+	}
 
-	of_property_read_string_index(np, "qcom,protection-domain",
-				      1, &adev->service_path);
+	/* Protection domain is optional, it does not exist on older platforms */
+	ret = of_property_read_string_index(np, "qcom,protection-domain",
+					    1, &adev->service_path);
+	if (ret < 0 && ret != -EINVAL) {
+		dev_err(dev, "Failed to read second value of qcom,protection-domain\n");
+		goto out;
+	}
 
 	dev_info(dev, "Adding APR dev: %s\n", dev_name(&adev->dev));
 
@@ -300,13 +333,14 @@
 		put_device(&adev->dev);
 	}
 
+out:
 	return ret;
 }
 
 static int of_apr_add_pd_lookups(struct device *dev)
 {
 	const char *service_name, *service_path;
-	struct apr *apr = dev_get_drvdata(dev);
+	struct packet_router *apr = dev_get_drvdata(dev);
 	struct device_node *node;
 	struct pdr_service *pds;
 	int ret;
@@ -321,12 +355,14 @@
 						    1, &service_path);
 		if (ret < 0) {
 			dev_err(dev, "pdr service path missing: %d\n", ret);
+			of_node_put(node);
 			return ret;
 		}
 
 		pds = pdr_add_lookup(apr->pdr, service_name, service_path);
 		if (IS_ERR(pds) && PTR_ERR(pds) != -EALREADY) {
 			dev_err(dev, "pdr add lookup failed: %ld\n", PTR_ERR(pds));
+			of_node_put(node);
 			return PTR_ERR(pds);
 		}
 	}
@@ -336,13 +372,14 @@
 
 static void of_register_apr_devices(struct device *dev, const char *svc_path)
 {
-	struct apr *apr = dev_get_drvdata(dev);
+	struct packet_router *apr = dev_get_drvdata(dev);
 	struct device_node *node;
 	const char *service_path;
 	int ret;
 
 	for_each_child_of_node(dev->of_node, node) {
-		struct apr_device_id id = { {0} };
+		u32 svc_id;
+		u32 domain_id;
 
 		/*
 		 * This function is called with svc_path NULL during
@@ -372,13 +409,13 @@
 				continue;
 		}
 
-		if (of_property_read_u32(node, "reg", &id.svc_id))
+		if (of_property_read_u32(node, "reg", &svc_id))
 			continue;
 
-		id.domain_id = apr->dest_domain_id;
+		domain_id = apr->dest_domain_id;
 
-		if (apr_add_device(dev, node, &id))
-			dev_err(dev, "Failed to add apr %d svc\n", id.svc_id);
+		if (apr_add_device(dev, node, svc_id, domain_id))
+			dev_err(dev, "Failed to add apr %d svc\n", svc_id);
 	}
 }
 
@@ -398,7 +435,7 @@
 
 static void apr_pd_status(int state, char *svc_path, void *priv)
 {
-	struct apr *apr = (struct apr *)priv;
+	struct packet_router *apr = (struct packet_router *)priv;
 
 	switch (state) {
 	case SERVREG_SERVICE_STATE_UP:
@@ -413,16 +450,20 @@
 static int apr_probe(struct rpmsg_device *rpdev)
 {
 	struct device *dev = &rpdev->dev;
-	struct apr *apr;
+	struct packet_router *apr;
 	int ret;
 
 	apr = devm_kzalloc(dev, sizeof(*apr), GFP_KERNEL);
 	if (!apr)
 		return -ENOMEM;
 
-	ret = of_property_read_u32(dev->of_node, "qcom,apr-domain", &apr->dest_domain_id);
+	ret = of_property_read_u32(dev->of_node, "qcom,domain", &apr->dest_domain_id);
+	if (ret) /* try deprecated apr-domain property */
+		ret = of_property_read_u32(dev->of_node, "qcom,apr-domain",
+					   &apr->dest_domain_id);
+	apr->type = PR_TYPE_APR;
 	if (ret) {
-		dev_err(dev, "APR Domain ID not specified in DT\n");
+		dev_err(dev, "Domain ID not specified in DT\n");
 		return ret;
 	}
 
@@ -465,7 +506,7 @@
 
 static void apr_remove(struct rpmsg_device *rpdev)
 {
-	struct apr *apr = dev_get_drvdata(&rpdev->dev);
+	struct packet_router *apr = dev_get_drvdata(&rpdev->dev);
 
 	pdr_handle_release(apr->pdr);
 	device_for_each_child(&rpdev->dev, NULL, apr_remove_device);
@@ -502,20 +543,20 @@
 }
 EXPORT_SYMBOL_GPL(apr_driver_unregister);
 
-static const struct of_device_id apr_of_match[] = {
+static const struct of_device_id pkt_router_of_match[] = {
 	{ .compatible = "qcom,apr"},
 	{ .compatible = "qcom,apr-v2"},
 	{}
 };
-MODULE_DEVICE_TABLE(of, apr_of_match);
+MODULE_DEVICE_TABLE(of, pkt_router_of_match);
 
-static struct rpmsg_driver apr_driver = {
+static struct rpmsg_driver packet_router_driver = {
 	.probe = apr_probe,
 	.remove = apr_remove,
 	.callback = apr_callback,
 	.drv = {
 		.name = "qcom,apr",
-		.of_match_table = apr_of_match,
+		.of_match_table = pkt_router_of_match,
 	},
 };
 
@@ -525,7 +566,7 @@
 
 	ret = bus_register(&aprbus);
 	if (!ret)
-		ret = register_rpmsg_driver(&apr_driver);
+		ret = register_rpmsg_driver(&packet_router_driver);
 	else
 		bus_unregister(&aprbus);
 
@@ -535,7 +576,7 @@
 static void __exit apr_exit(void)
 {
 	bus_unregister(&aprbus);
-	unregister_rpmsg_driver(&apr_driver);
+	unregister_rpmsg_driver(&packet_router_driver);
 }
 
 subsys_initcall(apr_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/cmd-db.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/cmd-db.c
@@ -1,6 +1,10 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-/* Copyright (c) 2016-2018, 2020, The Linux Foundation. All rights reserved. */
+/*
+ * Copyright (c) 2016-2018, 2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
 
+#include <linux/bitfield.h>
 #include <linux/debugfs.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -17,6 +21,8 @@
 #define MAX_SLV_ID		8
 #define SLAVE_ID_MASK		0x7
 #define SLAVE_ID_SHIFT		16
+#define SLAVE_ID(addr)		FIELD_GET(GENMASK(19, 16), addr)
+#define VRM_ADDR(addr)		FIELD_GET(GENMASK(19, 4), addr)
 
 /**
  * struct entry_header: header for each entry in cmddb
@@ -217,6 +223,30 @@
 EXPORT_SYMBOL(cmd_db_read_aux_data);
 
 /**
+ * cmd_db_match_resource_addr() - Compare if both Resource addresses are same
+ *
+ * @addr1: Resource address to compare
+ * @addr2: Resource address to compare
+ *
+ * Return: true if two addresses refer to the same resource, false otherwise
+ */
+bool cmd_db_match_resource_addr(u32 addr1, u32 addr2)
+{
+	/*
+	 * Each RPMh VRM accelerator resource has 3 or 4 contiguous 4-byte
+	 * aligned addresses associated with it. Ignore the offset to check
+	 * for VRM requests.
+	 */
+	if (addr1 == addr2)
+		return true;
+	else if (SLAVE_ID(addr1) == CMD_DB_HW_VRM && VRM_ADDR(addr1) == VRM_ADDR(addr2))
+		return true;
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(cmd_db_match_resource_addr);
+
+/**
  * cmd_db_read_slave_id - Get the slave ID for a given resource address
  *
  * @id: Resource id to query the DB for version
@@ -320,7 +350,7 @@
 		return -EINVAL;
 	}
 
-	cmd_db_header = memremap(rmem->base, rmem->size, MEMREMAP_WB);
+	cmd_db_header = memremap(rmem->base, rmem->size, MEMREMAP_WC);
 	if (!cmd_db_header) {
 		ret = -ENOMEM;
 		cmd_db_header = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/cpr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/cpr.c
@@ -1010,7 +1010,7 @@
 		return corner->uV;
 
 	temp = f_diff * (uV_high - uV_low);
-	do_div(temp, f_high - f_low);
+	temp = div64_ul(temp, f_high - f_low);
 
 	/*
 	 * max_volt_scale has units of uV/MHz while freq values
@@ -1710,12 +1710,16 @@
 
 	ret = of_genpd_add_provider_simple(dev->of_node, &drv->pd);
 	if (ret)
-		return ret;
+		goto err_remove_genpd;
 
 	platform_set_drvdata(pdev, drv);
 	cpr_debugfs_init(drv);
 
 	return 0;
+
+err_remove_genpd:
+	pm_genpd_remove(&drv->pd);
+	return ret;
 }
 
 static int cpr_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/llcc-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/llcc-qcom.c
@@ -115,7 +115,7 @@
 	{ LLCC_CMPT,     10, 768, 1, 1, 0x3f, 0x0, 0, 0, 0, 1, 0, 0},
 	{ LLCC_GPUHTW,   11, 256, 1, 1, 0x3f, 0x0, 0, 0, 0, 1, 0, 0},
 	{ LLCC_GPU,      12, 512, 1, 0, 0x3f, 0x0, 0, 0, 0, 1, 0, 0},
-	{ LLCC_MMUHWT,   13, 256, 1, 1, 0x3f, 0x0, 0, 0, 0, 1, 1, 0},
+	{ LLCC_MMUHWT,   13, 256, 1, 1, 0x3f, 0x0, 0, 0, 0, 0, 1, 0},
 	{ LLCC_MDMPNG,   21, 768, 0, 1, 0x3f, 0x0, 0, 0, 0, 1, 0, 0},
 	{ LLCC_WLHW,     24, 256, 1, 1, 0x3f, 0x0, 0, 0, 0, 1, 0, 0},
 	{ LLCC_MODPE,    29, 64,  1, 1, 0x3f, 0x0, 0, 0, 0, 1, 0, 0},
@@ -450,14 +450,14 @@
 		u32 disable_cap_alloc, retain_pc;
 
 		disable_cap_alloc = config->dis_cap_alloc << config->slice_id;
-		ret = regmap_write(drv_data->bcast_regmap,
-				LLCC_TRP_SCID_DIS_CAP_ALLOC, disable_cap_alloc);
+		ret = regmap_update_bits(drv_data->bcast_regmap, LLCC_TRP_SCID_DIS_CAP_ALLOC,
+					 BIT(config->slice_id), disable_cap_alloc);
 		if (ret)
 			return ret;
 
 		retain_pc = config->retain_on_pc << config->slice_id;
-		ret = regmap_write(drv_data->bcast_regmap,
-				LLCC_TRP_PCB_ACT, retain_pc);
+		ret = regmap_update_bits(drv_data->bcast_regmap, LLCC_TRP_PCB_ACT,
+					 BIT(config->slice_id), retain_pc);
 		if (ret)
 			return ret;
 	}
@@ -537,6 +537,9 @@
 	u32 sz;
 	u32 version;
 
+	if (!IS_ERR(drv_data))
+		return -EBUSY;
+
 	drv_data = devm_kzalloc(dev, sizeof(*drv_data), GFP_KERNEL);
 	if (!drv_data) {
 		ret = -ENOMEM;
@@ -607,7 +610,7 @@
 	if (ret)
 		goto err;
 
-	drv_data->ecc_irq = platform_get_irq(pdev, 0);
+	drv_data->ecc_irq = platform_get_irq_optional(pdev, 0);
 	if (drv_data->ecc_irq >= 0) {
 		llcc_edac = platform_device_register_data(&pdev->dev,
 						"qcom_llcc_edac", -1, drv_data,
@@ -630,6 +633,7 @@
 	{ .compatible = "qcom,sm8250-llcc", .data = &sm8250_cfg },
 	{ }
 };
+MODULE_DEVICE_TABLE(of, qcom_llcc_of_match);
 
 static struct platform_driver qcom_llcc_driver = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/ocmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/ocmem.c
@@ -76,8 +76,12 @@
 #define OCMEM_REG_GFX_MPU_START			0x00001004
 #define OCMEM_REG_GFX_MPU_END			0x00001008
 
-#define OCMEM_HW_PROFILE_NUM_PORTS(val)		FIELD_PREP(0x0000000f, (val))
-#define OCMEM_HW_PROFILE_NUM_MACROS(val)	FIELD_PREP(0x00003f00, (val))
+#define OCMEM_HW_VERSION_MAJOR(val)		FIELD_GET(GENMASK(31, 28), val)
+#define OCMEM_HW_VERSION_MINOR(val)		FIELD_GET(GENMASK(27, 16), val)
+#define OCMEM_HW_VERSION_STEP(val)		FIELD_GET(GENMASK(15, 0), val)
+
+#define OCMEM_HW_PROFILE_NUM_PORTS(val)		FIELD_GET(0x0000000f, (val))
+#define OCMEM_HW_PROFILE_NUM_MACROS(val)	FIELD_GET(0x00003f00, (val))
 
 #define OCMEM_HW_PROFILE_LAST_REGN_HALFSIZE	0x00010000
 #define OCMEM_HW_PROFILE_INTERLEAVING		0x00020000
@@ -194,18 +198,22 @@
 	devnode = of_parse_phandle(dev->of_node, "sram", 0);
 	if (!devnode || !devnode->parent) {
 		dev_err(dev, "Cannot look up sram phandle\n");
+		of_node_put(devnode);
 		return ERR_PTR(-ENODEV);
 	}
 
 	pdev = of_find_device_by_node(devnode->parent);
 	if (!pdev) {
 		dev_err(dev, "Cannot find device node %s\n", devnode->name);
+		of_node_put(devnode);
 		return ERR_PTR(-EPROBE_DEFER);
 	}
+	of_node_put(devnode);
 
 	ocmem = platform_get_drvdata(pdev);
 	if (!ocmem) {
 		dev_err(dev, "Cannot get ocmem\n");
+		put_device(&pdev->dev);
 		return ERR_PTR(-ENODEV);
 	}
 	return ocmem;
@@ -353,6 +361,12 @@
 		}
 	}
 
+	reg = ocmem_read(ocmem, OCMEM_REG_HW_VERSION);
+	dev_dbg(dev, "OCMEM hardware version: %lu.%lu.%lu\n",
+		OCMEM_HW_VERSION_MAJOR(reg),
+		OCMEM_HW_VERSION_MINOR(reg),
+		OCMEM_HW_VERSION_STEP(reg));
+
 	reg = ocmem_read(ocmem, OCMEM_REG_HW_PROFILE);
 	ocmem->num_ports = OCMEM_HW_PROFILE_NUM_PORTS(reg);
 	ocmem->num_macros = OCMEM_HW_PROFILE_NUM_MACROS(reg);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/pdr_interface.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/pdr_interface.c
@@ -74,24 +74,18 @@
 {
 	struct pdr_handle *pdr = container_of(qmi, struct pdr_handle,
 					      locator_hdl);
-	struct pdr_service *pds;
 
+	mutex_lock(&pdr->lock);
 	/* Create a local client port for QMI communication */
 	pdr->locator_addr.sq_family = AF_QIPCRTR;
 	pdr->locator_addr.sq_node = svc->node;
 	pdr->locator_addr.sq_port = svc->port;
 
-	mutex_lock(&pdr->lock);
 	pdr->locator_init_complete = true;
 	mutex_unlock(&pdr->lock);
 
 	/* Service pending lookup requests */
-	mutex_lock(&pdr->list_lock);
-	list_for_each_entry(pds, &pdr->lookups, node) {
-		if (pds->need_locator_lookup)
-			schedule_work(&pdr->locator_work);
-	}
-	mutex_unlock(&pdr->list_lock);
+	schedule_work(&pdr->locator_work);
 
 	return 0;
 }
@@ -104,10 +98,10 @@
 
 	mutex_lock(&pdr->lock);
 	pdr->locator_init_complete = false;
-	mutex_unlock(&pdr->lock);
 
 	pdr->locator_addr.sq_node = 0;
 	pdr->locator_addr.sq_port = 0;
+	mutex_unlock(&pdr->lock);
 }
 
 static const struct qmi_ops pdr_locator_ops = {
@@ -366,12 +360,14 @@
 	if (ret < 0)
 		return ret;
 
+	mutex_lock(&pdr->lock);
 	ret = qmi_send_request(&pdr->locator_hdl,
 			       &pdr->locator_addr,
 			       &txn, SERVREG_GET_DOMAIN_LIST_REQ,
 			       SERVREG_GET_DOMAIN_LIST_REQ_MAX_LEN,
 			       servreg_get_domain_list_req_ei,
 			       req);
+	mutex_unlock(&pdr->lock);
 	if (ret < 0) {
 		qmi_txn_cancel(&txn);
 		return ret;
@@ -416,7 +412,7 @@
 		if (ret < 0)
 			goto out;
 
-		for (i = domains_read; i < resp->domain_list_len; i++) {
+		for (i = 0; i < resp->domain_list_len; i++) {
 			entry = &resp->domain_list[i];
 
 			if (strnlen(entry->name, sizeof(entry->name)) == sizeof(entry->name))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/qcom-geni-se.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/qcom-geni-se.c
@@ -594,7 +594,8 @@
 
 	for (i = 0; i < MAX_CLK_PERF_LEVEL; i++) {
 		freq = clk_round_rate(se->clk, freq + 1);
-		if (freq <= 0 || freq == se->clk_perf_tbl[i - 1])
+		if (freq <= 0 ||
+		    (i > 0 && freq == se->clk_perf_tbl[i - 1]))
 			break;
 		se->clk_perf_tbl[i] = freq;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/qcom_aoss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/qcom_aoss.c
@@ -8,10 +8,12 @@
 #include <linux/io.h>
 #include <linux/mailbox_client.h>
 #include <linux/module.h>
+#include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
 #include <linux/thermal.h>
 #include <linux/slab.h>
+#include <linux/soc/qcom/qcom_aoss.h>
 
 #define QMP_DESC_MAGIC			0x0
 #define QMP_DESC_VERSION		0x4
@@ -223,11 +225,14 @@
  *
  * Return: 0 on success, negative errno on failure
  */
-static int qmp_send(struct qmp *qmp, const void *data, size_t len)
+int qmp_send(struct qmp *qmp, const void *data, size_t len)
 {
 	long time_left;
 	int ret;
 
+	if (WARN_ON(IS_ERR_OR_NULL(qmp) || !data))
+		return -EINVAL;
+
 	if (WARN_ON(len + sizeof(u32) > qmp->size))
 		return -EINVAL;
 
@@ -261,6 +266,7 @@
 
 	return ret;
 }
+EXPORT_SYMBOL(qmp_send);
 
 static int qmp_qdss_clk_prepare(struct clk_hw *hw)
 {
@@ -493,8 +499,10 @@
 			continue;
 		ret = qmp_cooling_device_add(qmp, &qmp->cooling_devs[count++],
 					     child);
-		if (ret)
+		if (ret) {
+			of_node_put(child);
 			goto unroll;
+		}
 	}
 
 	if (!count)
@@ -519,6 +527,55 @@
 		thermal_cooling_device_unregister(qmp->cooling_devs[i].cdev);
 }
 
+/**
+ * qmp_get() - get a qmp handle from a device
+ * @dev: client device pointer
+ *
+ * Return: handle to qmp device on success, ERR_PTR() on failure
+ */
+struct qmp *qmp_get(struct device *dev)
+{
+	struct platform_device *pdev;
+	struct device_node *np;
+	struct qmp *qmp;
+
+	if (!dev || !dev->of_node)
+		return ERR_PTR(-EINVAL);
+
+	np = of_parse_phandle(dev->of_node, "qcom,qmp", 0);
+	if (!np)
+		return ERR_PTR(-ENODEV);
+
+	pdev = of_find_device_by_node(np);
+	of_node_put(np);
+	if (!pdev)
+		return ERR_PTR(-EINVAL);
+
+	qmp = platform_get_drvdata(pdev);
+
+	if (!qmp) {
+		put_device(&pdev->dev);
+		return ERR_PTR(-EPROBE_DEFER);
+	}
+	return qmp;
+}
+EXPORT_SYMBOL(qmp_get);
+
+/**
+ * qmp_put() - release a qmp handle
+ * @qmp: qmp handle obtained from qmp_get()
+ */
+void qmp_put(struct qmp *qmp)
+{
+	/*
+	 * Match get_device() inside of_find_device_by_node() in
+	 * qmp_get()
+	 */
+	if (!IS_ERR_OR_NULL(qmp))
+		put_device(qmp->dev);
+}
+EXPORT_SYMBOL(qmp_put);
+
 static int qmp_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -548,7 +605,7 @@
 	}
 
 	irq = platform_get_irq(pdev, 0);
-	ret = devm_request_irq(&pdev->dev, irq, qmp_intr, IRQF_ONESHOT,
+	ret = devm_request_irq(&pdev->dev, irq, qmp_intr, 0,
 			       "aoss-qmp", qmp);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to request interrupt\n");
@@ -615,6 +672,7 @@
 	.driver = {
 		.name		= "qcom_aoss_qmp",
 		.of_match_table	= qmp_dt_match,
+		.suppress_bind_attrs = true,
 	},
 	.probe = qmp_probe,
 	.remove	= qmp_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/qmi_encdec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/qmi_encdec.c
@@ -534,8 +534,8 @@
 		decoded_bytes += rc;
 	}
 
-	if (string_len > temp_ei->elem_len) {
-		pr_err("%s: String len %d > Max Len %d\n",
+	if (string_len >= temp_ei->elem_len) {
+		pr_err("%s: String len %d >= Max Len %d\n",
 		       __func__, string_len, temp_ei->elem_len);
 		return -ETOOSMALL;
 	} else if (string_len > tlv_len) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/rpmh-rsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/rpmh-rsc.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023-2024, Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #define pr_fmt(fmt) "%s " fmt, KBUILD_MODNAME
@@ -519,7 +520,7 @@
 		for_each_set_bit(j, &curr_enabled, MAX_CMDS_PER_TCS) {
 			addr = read_tcs_cmd(drv, RSC_DRV_CMD_ADDR, i, j);
 			for (k = 0; k < msg->num_cmds; k++) {
-				if (addr == msg->cmds[k].addr)
+				if (cmd_db_match_resource_addr(msg->cmds[k].addr, addr))
 					return -EBUSY;
 			}
 		}
@@ -607,13 +608,14 @@
 {
 	struct tcs_group *tcs;
 	int tcs_id;
-	unsigned long flags;
+
+	might_sleep();
 
 	tcs = get_tcs_for_msg(drv, msg);
 	if (IS_ERR(tcs))
 		return PTR_ERR(tcs);
 
-	spin_lock_irqsave(&drv->lock, flags);
+	spin_lock_irq(&drv->lock);
 
 	/* Wait forever for a free tcs. It better be there eventually! */
 	wait_event_lock_irq(drv->tcs_wait,
@@ -631,7 +633,7 @@
 		write_tcs_reg_sync(drv, RSC_DRV_CMD_ENABLE, tcs_id, 0);
 		enable_tcs_irq(drv, tcs_id, true);
 	}
-	spin_unlock_irqrestore(&drv->lock, flags);
+	spin_unlock_irq(&drv->lock);
 
 	/*
 	 * These two can be done after the lock is released because:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/rpmh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/rpmh.c
@@ -189,7 +189,6 @@
 	}
 
 	if (state == RPMH_ACTIVE_ONLY_STATE) {
-		WARN_ON(irqs_disabled());
 		ret = rpmh_rsc_send_data(ctrlr_to_drv(ctrlr), &rpm_msg->msg);
 	} else {
 		/* Clean up our call by spoofing tx_done */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/rpmhpd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/rpmhpd.c
@@ -30,6 +30,7 @@
  * @active_only:	True if it represents an Active only peer
  * @corner:		current corner
  * @active_corner:	current active corner
+ * @enable_corner:	lowest non-zero corner
  * @level:		An array of level (vlvl) to corner (hlvl) mappings
  *			derived from cmd-db
  * @level_count:	Number of levels supported by the power domain. max
@@ -47,6 +48,7 @@
 	const bool	active_only;
 	unsigned int	corner;
 	unsigned int	active_corner;
+	unsigned int	enable_corner;
 	u32		level[RPMH_ARC_MAX_LEVELS];
 	size_t		level_count;
 	bool		enabled;
@@ -204,7 +206,7 @@
 static struct rpmhpd sm8350_mxc_ao;
 static struct rpmhpd sm8350_mxc = {
 	.pd = { .name = "mxc", },
-	.peer = &sm8150_mmcx_ao,
+	.peer = &sm8350_mxc_ao,
 	.res_name = "mxc.lvl",
 };
 
@@ -349,12 +351,15 @@
 	unsigned int active_corner, sleep_corner;
 	unsigned int this_active_corner = 0, this_sleep_corner = 0;
 	unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
+	unsigned int peer_enabled_corner;
 
 	to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
 
-	if (peer && peer->enabled)
-		to_active_sleep(peer, peer->corner, &peer_active_corner,
+	if (peer && peer->enabled) {
+		peer_enabled_corner = max(peer->corner, peer->enable_corner);
+		to_active_sleep(peer, peer_enabled_corner, &peer_active_corner,
 				&peer_sleep_corner);
+	}
 
 	active_corner = max(this_active_corner, peer_active_corner);
 
@@ -385,13 +390,13 @@
 static int rpmhpd_power_on(struct generic_pm_domain *domain)
 {
 	struct rpmhpd *pd = domain_to_rpmhpd(domain);
-	int ret = 0;
+	unsigned int corner;
+	int ret;
 
 	mutex_lock(&rpmhpd_lock);
 
-	if (pd->corner)
-		ret = rpmhpd_aggregate_corner(pd, pd->corner);
-
+	corner = max(pd->corner, pd->enable_corner);
+	ret = rpmhpd_aggregate_corner(pd, corner);
 	if (!ret)
 		pd->enabled = true;
 
@@ -436,6 +441,10 @@
 		i--;
 
 	if (pd->enabled) {
+		/* Ensure that the domain isn't turn off */
+		if (i < pd->enable_corner)
+			i = pd->enable_corner;
+
 		ret = rpmhpd_aggregate_corner(pd, i);
 		if (ret)
 			goto out;
@@ -472,6 +481,10 @@
 	for (i = 0; i < rpmhpd->level_count; i++) {
 		rpmhpd->level[i] = buf[i];
 
+		/* Remember the first corner with non-zero level */
+		if (!rpmhpd->level[rpmhpd->enable_corner] && rpmhpd->level[i])
+			rpmhpd->enable_corner = i;
+
 		/*
 		 * The AUX data may be zero padded.  These 0 valued entries at
 		 * the end of the map must be ignored.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/rpmpd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/rpmpd.c
@@ -546,6 +546,9 @@
 
 	data->domains = devm_kcalloc(&pdev->dev, num, sizeof(*data->domains),
 				     GFP_KERNEL);
+	if (!data->domains)
+		return -ENOMEM;
+
 	data->num_domains = num;
 
 	for (i = 0; i < num; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/smem_state.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/smem_state.c
@@ -116,7 +116,8 @@
 
 	if (args.args_count != 1) {
 		dev_err(dev, "invalid #qcom,smem-state-cells\n");
-		return ERR_PTR(-EINVAL);
+		state = ERR_PTR(-EINVAL);
+		goto put;
 	}
 
 	state = of_node_to_state(args.np);
@@ -136,6 +137,7 @@
 	struct qcom_smem_state *state = container_of(ref, struct qcom_smem_state, refcount);
 
 	list_del(&state->list);
+	of_node_put(state->of_node);
 	kfree(state);
 }
 
@@ -205,7 +207,7 @@
 
 	kref_init(&state->refcount);
 
-	state->of_node = of_node;
+	state->of_node = of_node_get(of_node);
 	state->ops = *ops;
 	state->priv = priv;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/smp2p.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/smp2p.c
@@ -421,6 +421,7 @@
 	}
 
 	smp2p->ipc_regmap = syscon_node_to_regmap(syscon);
+	of_node_put(syscon);
 	if (IS_ERR(smp2p->ipc_regmap))
 		return PTR_ERR(smp2p->ipc_regmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/smsm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/smsm.c
@@ -374,6 +374,7 @@
 		return 0;
 
 	host->ipc_regmap = syscon_node_to_regmap(syscon);
+	of_node_put(syscon);
 	if (IS_ERR(host->ipc_regmap))
 		return PTR_ERR(host->ipc_regmap);
 
@@ -525,7 +526,7 @@
 	for (id = 0; id < smsm->num_hosts; id++) {
 		ret = smsm_parse_ipc(smsm, id);
 		if (ret < 0)
-			return ret;
+			goto out_put;
 	}
 
 	/* Acquire the main SMSM state vector */
@@ -533,13 +534,14 @@
 			      smsm->num_entries * sizeof(u32));
 	if (ret < 0 && ret != -EEXIST) {
 		dev_err(&pdev->dev, "unable to allocate shared state entry\n");
-		return ret;
+		goto out_put;
 	}
 
 	states = qcom_smem_get(QCOM_SMEM_HOST_ANY, SMEM_SMSM_SHARED_STATE, NULL);
 	if (IS_ERR(states)) {
 		dev_err(&pdev->dev, "Unable to acquire shared state entry\n");
-		return PTR_ERR(states);
+		ret = PTR_ERR(states);
+		goto out_put;
 	}
 
 	/* Acquire the list of interrupt mask vectors */
@@ -547,13 +549,14 @@
 	ret = qcom_smem_alloc(QCOM_SMEM_HOST_ANY, SMEM_SMSM_CPU_INTR_MASK, size);
 	if (ret < 0 && ret != -EEXIST) {
 		dev_err(&pdev->dev, "unable to allocate smsm interrupt mask\n");
-		return ret;
+		goto out_put;
 	}
 
 	intr_mask = qcom_smem_get(QCOM_SMEM_HOST_ANY, SMEM_SMSM_CPU_INTR_MASK, NULL);
 	if (IS_ERR(intr_mask)) {
 		dev_err(&pdev->dev, "unable to acquire shared memory interrupt mask\n");
-		return PTR_ERR(intr_mask);
+		ret = PTR_ERR(intr_mask);
+		goto out_put;
 	}
 
 	/* Setup the reference to the local state bits */
@@ -564,7 +567,8 @@
 	smsm->state = qcom_smem_state_register(local_node, &smsm_state_ops, smsm);
 	if (IS_ERR(smsm->state)) {
 		dev_err(smsm->dev, "failed to register qcom_smem_state\n");
-		return PTR_ERR(smsm->state);
+		ret = PTR_ERR(smsm->state);
+		goto out_put;
 	}
 
 	/* Register handlers for remote processor entries of interest. */
@@ -594,16 +598,19 @@
 	}
 
 	platform_set_drvdata(pdev, smsm);
+	of_node_put(local_node);
 
 	return 0;
 
 unwind_interfaces:
+	of_node_put(node);
 	for (id = 0; id < smsm->num_entries; id++)
 		if (smsm->entries[id].domain)
 			irq_domain_remove(smsm->entries[id].domain);
 
 	qcom_smem_state_unregister(smsm->state);
-
+out_put:
+	of_node_put(local_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/qcom/socinfo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/qcom/socinfo.c
@@ -87,8 +87,8 @@
 	[15] = "PM8901",
 	[16] = "PM8950/PM8027",
 	[17] = "PMI8950/ISL9519",
-	[18] = "PM8921",
-	[19] = "PM8018",
+	[18] = "PMK8001/PM8921",
+	[19] = "PMI8996/PM8018",
 	[20] = "PM8998/PM8015",
 	[21] = "PMI8998/PM8014",
 	[22] = "PM8821",
@@ -614,10 +614,16 @@
 	qs->attr.revision = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%u.%u",
 					   SOCINFO_MAJOR(le32_to_cpu(info->ver)),
 					   SOCINFO_MINOR(le32_to_cpu(info->ver)));
-	if (offsetof(struct socinfo, serial_num) <= item_size)
+	if (!qs->attr.soc_id || !qs->attr.revision)
+		return -ENOMEM;
+
+	if (offsetofend(struct socinfo, serial_num) <= item_size) {
 		qs->attr.serial_number = devm_kasprintf(&pdev->dev, GFP_KERNEL,
 							"%u",
 							le32_to_cpu(info->serial_num));
+		if (!qs->attr.serial_number)
+			return -ENOMEM;
+	}
 
 	qs->soc_dev = soc_device_register(&qs->attr);
 	if (IS_ERR(qs->soc_dev))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/renesas/r8a77980-sysc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/renesas/r8a77980-sysc.c
@@ -25,7 +25,8 @@
 	  PD_CPU_NOCR },
 	{ "ca53-cpu3",	0x200, 3, R8A77980_PD_CA53_CPU3, R8A77980_PD_CA53_SCU,
 	  PD_CPU_NOCR },
-	{ "cr7",	0x240, 0, R8A77980_PD_CR7,	R8A77980_PD_ALWAYS_ON },
+	{ "cr7",	0x240, 0, R8A77980_PD_CR7,	R8A77980_PD_ALWAYS_ON,
+	  PD_CPU_NOCR },
 	{ "a3ir",	0x180, 0, R8A77980_PD_A3IR,	R8A77980_PD_ALWAYS_ON },
 	{ "a2ir0",	0x400, 0, R8A77980_PD_A2IR0,	R8A77980_PD_A3IR },
 	{ "a2ir1",	0x400, 1, R8A77980_PD_A2IR1,	R8A77980_PD_A3IR },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/renesas/r8a779a0-sysc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/renesas/r8a779a0-sysc.c
@@ -83,11 +83,11 @@
 	{ "a2cv6",	R8A779A0_PD_A2CV6, R8A779A0_PD_A3IR },
 	{ "a2cn2",	R8A779A0_PD_A2CN2, R8A779A0_PD_A3IR },
 	{ "a2imp23",	R8A779A0_PD_A2IMP23, R8A779A0_PD_A3IR },
-	{ "a2dp1",	R8A779A0_PD_A2DP0, R8A779A0_PD_A3IR },
-	{ "a2cv2",	R8A779A0_PD_A2CV0, R8A779A0_PD_A3IR },
-	{ "a2cv3",	R8A779A0_PD_A2CV1, R8A779A0_PD_A3IR },
-	{ "a2cv5",	R8A779A0_PD_A2CV4, R8A779A0_PD_A3IR },
-	{ "a2cv7",	R8A779A0_PD_A2CV6, R8A779A0_PD_A3IR },
+	{ "a2dp1",	R8A779A0_PD_A2DP1, R8A779A0_PD_A3IR },
+	{ "a2cv2",	R8A779A0_PD_A2CV2, R8A779A0_PD_A3IR },
+	{ "a2cv3",	R8A779A0_PD_A2CV3, R8A779A0_PD_A3IR },
+	{ "a2cv5",	R8A779A0_PD_A2CV5, R8A779A0_PD_A3IR },
+	{ "a2cv7",	R8A779A0_PD_A2CV7, R8A779A0_PD_A3IR },
 	{ "a2cn1",	R8A779A0_PD_A2CN1, R8A779A0_PD_A3IR },
 	{ "a1cnn0",	R8A779A0_PD_A1CNN0, R8A779A0_PD_A2CN0 },
 	{ "a1cnn2",	R8A779A0_PD_A1CNN2, R8A779A0_PD_A2CN2 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/rockchip/grf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/rockchip/grf.c
@@ -148,12 +148,14 @@
 		return -ENODEV;
 	if (!match || !match->data) {
 		pr_err("%s: missing grf data\n", __func__);
+		of_node_put(np);
 		return -EINVAL;
 	}
 
 	grf_info = match->data;
 
 	grf = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (IS_ERR(grf)) {
 		pr_err("%s: could not get grf syscon\n", __func__);
 		return PTR_ERR(grf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/samsung/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/samsung/Kconfig
@@ -25,6 +25,7 @@
 	bool "Exynos PMU controller driver" if COMPILE_TEST
 	depends on ARCH_EXYNOS || ((ARM || ARM64) && COMPILE_TEST)
 	select EXYNOS_PMU_ARM_DRIVERS if ARM && ARCH_EXYNOS
+	select MFD_CORE
 
 # There is no need to enable these drivers for ARMv8
 config EXYNOS_PMU_ARM_DRIVERS
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/sifive/sifive_l2_cache.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/sifive/sifive_l2_cache.c
@@ -202,17 +202,22 @@
 	if (!np)
 		return -ENODEV;
 
-	if (of_address_to_resource(np, 0, &res))
-		return -ENODEV;
+	if (of_address_to_resource(np, 0, &res)) {
+		rc = -ENODEV;
+		goto err_node_put;
+	}
 
 	l2_base = ioremap(res.start, resource_size(&res));
-	if (!l2_base)
-		return -ENOMEM;
+	if (!l2_base) {
+		rc = -ENOMEM;
+		goto err_node_put;
+	}
 
 	intr_num = of_property_count_u32_elems(np, "interrupts");
 	if (!intr_num) {
 		pr_err("L2CACHE: no interrupts property\n");
-		return -ENODEV;
+		rc = -ENODEV;
+		goto err_unmap;
 	}
 
 	for (i = 0; i < intr_num; i++) {
@@ -220,9 +225,10 @@
 		rc = request_irq(g_irq[i], l2_int_handler, 0, "l2_ecc", NULL);
 		if (rc) {
 			pr_err("L2CACHE: Could not request IRQ %d\n", g_irq[i]);
-			return rc;
+			goto err_free_irq;
 		}
 	}
+	of_node_put(np);
 
 	l2_config_read();
 
@@ -233,5 +239,14 @@
 	setup_sifive_debug();
 #endif
 	return 0;
+
+err_free_irq:
+	while (--i >= 0)
+		free_irq(g_irq[i], NULL);
+err_unmap:
+	iounmap(l2_base);
+err_node_put:
+	of_node_put(np);
+	return rc;
 }
 device_initcall(sifive_l2_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/sunxi/sunxi_sram.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/sunxi/sunxi_sram.c
@@ -78,8 +78,8 @@
 
 static struct sunxi_sram_desc sun50i_a64_sram_c = {
 	.data	= SUNXI_SRAM_DATA("C", 0x4, 24, 1,
-				  SUNXI_SRAM_MAP(0, 1, "cpu"),
-				  SUNXI_SRAM_MAP(1, 0, "de2")),
+				  SUNXI_SRAM_MAP(1, 0, "cpu"),
+				  SUNXI_SRAM_MAP(0, 1, "de2")),
 };
 
 static const struct of_device_id sunxi_sram_dt_ids[] = {
@@ -254,6 +254,7 @@
 	writel(val | ((device << sram_data->offset) & mask),
 	       base + sram_data->reg);
 
+	sram_desc->claimed = true;
 	spin_unlock(&sram_lock);
 
 	return 0;
@@ -329,12 +330,11 @@
 	.writeable_reg	= sunxi_sram_regmap_accessible_reg,
 };
 
-static int sunxi_sram_probe(struct platform_device *pdev)
+static int __init sunxi_sram_probe(struct platform_device *pdev)
 {
-	struct resource *res;
-	struct dentry *d;
 	struct regmap *emac_clock;
 	const struct sunxi_sramc_variant *variant;
+	struct device *dev = &pdev->dev;
 
 	sram_dev = &pdev->dev;
 
@@ -342,18 +342,10 @@
 	if (!variant)
 		return -EINVAL;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	base = devm_ioremap_resource(&pdev->dev, res);
+	base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(base))
 		return PTR_ERR(base);
 
-	of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
-
-	d = debugfs_create_file("sram", S_IRUGO, NULL, NULL,
-				&sunxi_sram_fops);
-	if (!d)
-		return -ENOMEM;
-
 	if (variant->num_emac_clocks > 0) {
 		emac_clock = devm_regmap_init_mmio(&pdev->dev, base,
 						   &sunxi_sram_emac_clock_regmap);
@@ -362,6 +354,10 @@
 			return PTR_ERR(emac_clock);
 	}
 
+	of_platform_populate(dev->of_node, NULL, NULL, dev);
+
+	debugfs_create_file("sram", 0444, NULL, NULL, &sunxi_sram_fops);
+
 	return 0;
 }
 
@@ -411,9 +407,8 @@
 		.name		= "sunxi-sram",
 		.of_match_table	= sunxi_sram_dt_match,
 	},
-	.probe	= sunxi_sram_probe,
 };
-module_platform_driver(sunxi_sram_driver);
+builtin_platform_driver_probe(sunxi_sram_driver, sunxi_sram_probe);
 
 MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
 MODULE_DESCRIPTION("Allwinner sunXi SRAM Controller Driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/tegra/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/tegra/Kconfig
@@ -136,7 +136,6 @@
 	def_bool y
 	depends on ARCH_TEGRA
 	select SOC_BUS
-	select TEGRA20_APB_DMA if ARCH_TEGRA_2x_SOC
 
 config SOC_TEGRA_FLOWCTRL
 	bool
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/tegra/fuse/fuse-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/tegra/fuse/fuse-tegra.c
@@ -320,7 +320,7 @@
 };
 builtin_platform_driver(tegra_fuse_driver);
 
-bool __init tegra_fuse_read_spare(unsigned int spare)
+u32 __init tegra_fuse_read_spare(unsigned int spare)
 {
 	unsigned int offset = fuse->soc->info->spare + spare * 4;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/tegra/fuse/fuse.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/tegra/fuse/fuse.h
@@ -65,7 +65,7 @@
 void tegra_init_revision(void);
 void tegra_init_apbmisc(void);
 
-bool __init tegra_fuse_read_spare(unsigned int spare);
+u32 __init tegra_fuse_read_spare(unsigned int spare);
 u32 __init tegra_fuse_read_early(unsigned int offset);
 
 u8 tegra_get_major_rev(void);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/tegra/pmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/tegra/pmc.c
@@ -782,7 +782,7 @@
 
 	err = reset_control_deassert(pg->reset);
 	if (err)
-		goto powergate_off;
+		goto disable_clks;
 
 	usleep_range(10, 20);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ti/knav_qmss_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ti/knav_qmss_queue.c
@@ -67,7 +67,7 @@
  * Newest followed by older ones. Search is done from start of the array
  * until a firmware file is found.
  */
-const char *knav_acc_firmwares[] = {"ks2_qmss_pdsp_acc48.bin"};
+static const char * const knav_acc_firmwares[] = {"ks2_qmss_pdsp_acc48.bin"};
 
 static bool device_ready;
 bool knav_qmss_device_ready(void)
@@ -1785,9 +1785,9 @@
 	INIT_LIST_HEAD(&kdev->pdsps);
 
 	pm_runtime_enable(&pdev->dev);
-	ret = pm_runtime_get_sync(&pdev->dev);
+	ret = pm_runtime_resume_and_get(&pdev->dev);
 	if (ret < 0) {
-		pm_runtime_put_noidle(&pdev->dev);
+		pm_runtime_disable(&pdev->dev);
 		dev_err(dev, "Failed to enable QMSS\n");
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ti/pm33xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ti/pm33xx.c
@@ -527,7 +527,7 @@
 
 	ret = am33xx_pm_alloc_sram();
 	if (ret)
-		return ret;
+		goto err_wkup_m3_ipc_put;
 
 	ret = am33xx_pm_rtc_setup();
 	if (ret)
@@ -574,13 +574,14 @@
 	pm_runtime_put_sync(dev);
 err_pm_runtime_disable:
 	pm_runtime_disable(dev);
-	wkup_m3_ipc_put(m3_ipc);
 err_unsetup_rtc:
 	iounmap(rtc_base_virt);
 	clk_put(rtc_fck);
 err_free_sram:
 	am33xx_pm_free_sram();
 	pm33xx_dev = NULL;
+err_wkup_m3_ipc_put:
+	wkup_m3_ipc_put(m3_ipc);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ti/pruss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ti/pruss.c
@@ -129,7 +129,7 @@
 
 	clks_np = of_get_child_by_name(cfg_node, "clocks");
 	if (!clks_np) {
-		dev_err(dev, "%pOF is missing its 'clocks' node\n", clks_np);
+		dev_err(dev, "%pOF is missing its 'clocks' node\n", cfg_node);
 		return -ENODEV;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ti/smartreflex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ti/smartreflex.c
@@ -203,10 +203,10 @@
 
 	if (sr_class->notify && sr_class->notify_flags && sr_info->irq) {
 		ret = devm_request_irq(&sr_info->pdev->dev, sr_info->irq,
-				       sr_interrupt, 0, sr_info->name, sr_info);
+				       sr_interrupt, IRQF_NO_AUTOEN,
+				       sr_info->name, sr_info);
 		if (ret)
 			goto error;
-		disable_irq(sr_info->irq);
 	}
 
 	if (pdata && pdata->enable_on_init)
@@ -931,6 +931,7 @@
 err_debugfs:
 	debugfs_remove_recursive(sr_info->dbg_dir);
 err_list_del:
+	pm_runtime_disable(&pdev->dev);
 	list_del(&sr_info->node);
 	clk_unprepare(sr_info->fck);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ti/ti_sci_pm_domains.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ti/ti_sci_pm_domains.c
@@ -114,6 +114,18 @@
 };
 MODULE_DEVICE_TABLE(of, ti_sci_pm_domain_matches);
 
+static bool ti_sci_pm_idx_exists(struct ti_sci_genpd_provider *pd_provider, u32 idx)
+{
+	struct ti_sci_pm_domain *pd;
+
+	list_for_each_entry(pd, &pd_provider->pd_list, node) {
+		if (pd->idx == idx)
+			return true;
+	}
+
+	return false;
+}
+
 static int ti_sci_pm_domain_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -153,8 +165,15 @@
 				break;
 
 			if (args.args_count >= 1 && args.np == dev->of_node) {
-				if (args.args[0] > max_id)
+				of_node_put(args.np);
+				if (args.args[0] > max_id) {
 					max_id = args.args[0];
+				} else {
+					if (ti_sci_pm_idx_exists(pd_provider, args.args[0])) {
+						index++;
+						continue;
+					}
+				}
 
 				pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
 				if (!pd)
@@ -174,7 +193,10 @@
 				pm_genpd_init(&pd->pd, NULL, true);
 
 				list_add(&pd->node, &pd_provider->pd_list);
+			} else {
+				of_node_put(args.np);
 			}
+
 			index++;
 		}
 	}
@@ -183,6 +205,8 @@
 		devm_kcalloc(dev, max_id + 1,
 			     sizeof(*pd_provider->data.domains),
 			     GFP_KERNEL);
+	if (!pd_provider->data.domains)
+		return -ENOMEM;
 
 	pd_provider->data.num_domains = max_id + 1;
 	pd_provider->data.xlate = ti_sci_pd_xlate;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ti/wkup_m3_ipc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ti/wkup_m3_ipc.c
@@ -14,7 +14,6 @@
 #include <linux/irq.h>
 #include <linux/module.h>
 #include <linux/of.h>
-#include <linux/omap-mailbox.h>
 #include <linux/platform_device.h>
 #include <linux/remoteproc.h>
 #include <linux/suspend.h>
@@ -151,7 +150,6 @@
 static int wkup_m3_ping(struct wkup_m3_ipc *m3_ipc)
 {
 	struct device *dev = m3_ipc->dev;
-	mbox_msg_t dummy_msg = 0;
 	int ret;
 
 	if (!m3_ipc->mbox) {
@@ -167,7 +165,7 @@
 	 * the RX callback to avoid multiple interrupts being received
 	 * by the CM3.
 	 */
-	ret = mbox_send_message(m3_ipc->mbox, &dummy_msg);
+	ret = mbox_send_message(m3_ipc->mbox, NULL);
 	if (ret < 0) {
 		dev_err(dev, "%s: mbox_send_message() failed: %d\n",
 			__func__, ret);
@@ -189,7 +187,6 @@
 static int wkup_m3_ping_noirq(struct wkup_m3_ipc *m3_ipc)
 {
 	struct device *dev = m3_ipc->dev;
-	mbox_msg_t dummy_msg = 0;
 	int ret;
 
 	if (!m3_ipc->mbox) {
@@ -198,7 +195,7 @@
 		return -EIO;
 	}
 
-	ret = mbox_send_message(m3_ipc->mbox, &dummy_msg);
+	ret = mbox_send_message(m3_ipc->mbox, NULL);
 	if (ret < 0) {
 		dev_err(dev, "%s: mbox_send_message() failed: %d\n",
 			__func__, ret);
@@ -449,9 +446,9 @@
 		return PTR_ERR(m3_ipc->ipc_mem_base);
 
 	irq = platform_get_irq(pdev, 0);
-	if (!irq) {
+	if (irq < 0) {
 		dev_err(&pdev->dev, "no irq resource\n");
-		return -ENXIO;
+		return irq;
 	}
 
 	ret = devm_request_irq(dev, irq, wkup_m3_txev_handler,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/ux500/ux500-soc-id.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/ux500/ux500-soc-id.c
@@ -167,20 +167,18 @@
 static const char *db8500_read_soc_id(struct device_node *backupram)
 {
 	void __iomem *base;
-	void __iomem *uid;
 	const char *retstr;
+	u32 uid[5];
 
 	base = of_iomap(backupram, 0);
 	if (!base)
 		return NULL;
-	uid = base + 0x1fc0;
+	memcpy_fromio(uid, base + 0x1fc0, sizeof(uid));
 
 	/* Throw these device-specific numbers into the entropy pool */
-	add_device_randomness(uid, 0x14);
+	add_device_randomness(uid, sizeof(uid));
 	retstr = kasprintf(GFP_KERNEL, "%08x%08x%08x%08x%08x",
-			 readl((u32 *)uid+0),
-			 readl((u32 *)uid+1), readl((u32 *)uid+2),
-			 readl((u32 *)uid+3), readl((u32 *)uid+4));
+			   uid[0], uid[1], uid[2], uid[3], uid[4]);
 	iounmap(base);
 	return retstr;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/versatile/soc-integrator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/versatile/soc-integrator.c
@@ -113,6 +113,7 @@
 		return -ENODEV;
 
 	syscon_regmap = syscon_node_to_regmap(np);
+	of_node_put(np);
 	if (IS_ERR(syscon_regmap))
 		return PTR_ERR(syscon_regmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/versatile/soc-realview.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/versatile/soc-realview.c
@@ -4,6 +4,7 @@
  *
  * Author: Linus Walleij <linus.walleij@linaro.org>
  */
+#include <linux/device.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/slab.h>
@@ -81,6 +82,13 @@
 
 ATTRIBUTE_GROUPS(realview);
 
+static void realview_soc_socdev_release(void *data)
+{
+	struct soc_device *soc_dev = data;
+
+	soc_device_unregister(soc_dev);
+}
+
 static int realview_soc_probe(struct platform_device *pdev)
 {
 	struct regmap *syscon_regmap;
@@ -93,7 +101,7 @@
 	if (IS_ERR(syscon_regmap))
 		return PTR_ERR(syscon_regmap);
 
-	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
+	soc_dev_attr = devm_kzalloc(&pdev->dev, sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
 		return -ENOMEM;
 
@@ -106,10 +114,14 @@
 	soc_dev_attr->family = "Versatile";
 	soc_dev_attr->custom_attr_group = realview_groups[0];
 	soc_dev = soc_device_register(soc_dev_attr);
-	if (IS_ERR(soc_dev)) {
-		kfree(soc_dev_attr);
+	if (IS_ERR(soc_dev))
 		return -ENODEV;
-	}
+
+	ret = devm_add_action_or_reset(&pdev->dev, realview_soc_socdev_release,
+				       soc_dev);
+	if (ret)
+		return ret;
+
 	ret = regmap_read(syscon_regmap, REALVIEW_SYS_ID_OFFSET,
 			  &realview_coreid);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/xilinx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/xilinx/Kconfig
@@ -25,4 +25,14 @@
 	  Say yes to enable device power management through PM domains
 	  If in doubt, say N.
 
+config XLNX_EVENT_MANAGER
+	bool "Enable Xilinx Event Management Driver"
+	depends on ZYNQMP_FIRMWARE
+	default ZYNQMP_FIRMWARE
+	help
+	  Say yes to enable event management support for Xilinx.
+	  This driver uses firmware driver as an interface for event/power
+	  management request to firmware.
+
+	  If in doubt, say N.
 endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/xilinx/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_ZYNQMP_POWER)	+= zynqmp_power.o
 obj-$(CONFIG_ZYNQMP_PM_DOMAINS) += zynqmp_pm_domains.o
+obj-$(CONFIG_XLNX_EVENT_MANAGER)	+= xlnx_event_manager.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/xilinx/xlnx_event_manager.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/xilinx/xlnx_event_manager.c
@@ -0,0 +1,605 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Event Management Driver
+ *
+ *  Copyright (C) 2021 Xilinx, Inc.
+ *
+ *  Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
+ */
+
+#include <linux/cpuhotplug.h>
+#include <linux/firmware/xlnx-error-events.h>
+#include <linux/firmware/xlnx-event-manager.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/hashtable.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+static DEFINE_PER_CPU_READ_MOSTLY(int, cpu_number1);
+
+static int virq_sgi;
+static int event_manager_availability = -EACCES;
+
+/* SGI number used for Event management driver */
+#define XLNX_EVENT_SGI_NUM	(15)
+
+/* Max number of driver can register for same event */
+#define MAX_DRIVER_PER_EVENT	(10U)
+
+/* Max HashMap Order for PM API feature check (1<<7 = 128) */
+#define REGISTERED_DRIVER_MAX_ORDER	(7)
+
+#define MAX_BITS	(32U) /* Number of bits available for error mask */
+
+#define REGISTER_NOTIFIER_FIRMWARE_VERSION	(2U)
+
+static DEFINE_HASHTABLE(reg_driver_map, REGISTERED_DRIVER_MAX_ORDER);
+static int sgi_num = XLNX_EVENT_SGI_NUM;
+
+/**
+ * struct registered_event_data - Registered Event Data.
+ * @key:		key is the combine id(Node-Id | Event-Id) of type u64
+ *			where upper u32 for Node-Id and lower u32 for Event-Id,
+ *			And this used as key to index into hashmap.
+ * @agent_data:		Data passed back to handler function.
+ * @cb_type:		Type of Api callback, like PM_NOTIFY_CB, etc.
+ * @eve_cb:		Function pointer to store the callback function.
+ * @wake:		If this flag set, firmware will wakeup processor if is
+ *			in sleep or power down state.
+ * @hentry:		hlist_node that hooks this entry into hashtable.
+ */
+struct registered_event_data {
+	u64 key;
+	enum pm_api_cb_id cb_type;
+	void *agent_data;
+
+	event_cb_func_t eve_cb;
+	bool wake;
+	struct hlist_node hentry;
+};
+
+static bool xlnx_is_error_event(const u32 node_id)
+{
+	if (node_id == XPM_NODETYPE_EVENT_ERROR_PMC_ERR1 ||
+	    node_id == XPM_NODETYPE_EVENT_ERROR_PMC_ERR2 ||
+	    node_id == XPM_NODETYPE_EVENT_ERROR_PSM_ERR1 ||
+	    node_id == XPM_NODETYPE_EVENT_ERROR_PSM_ERR2 ||
+	    node_id == XPM_NODETYPE_EVENT_ERROR_SW_ERR)
+		return true;
+
+	return false;
+}
+
+static int xlnx_add_cb_for_notify_event(const u32 node_id, const u32 event, const bool wake,
+					event_cb_func_t cb_fun,	void *data)
+{
+	u64 key = 0;
+	struct registered_event_data *eve_data;
+
+	key = ((u64)node_id << 32U) | (u64)event;
+	/* Check for existing entry in hash table for given key id */
+	hash_for_each_possible(reg_driver_map, eve_data, hentry, key) {
+		if (eve_data->key == key) {
+			pr_err("Found as already registered\n");
+			return -EINVAL;
+		}
+	}
+
+	/* Add new entry if not present */
+	eve_data = kmalloc(sizeof(*eve_data), GFP_KERNEL);
+	if (!eve_data)
+		return -ENOMEM;
+
+	eve_data->key = key;
+	eve_data->cb_type = PM_NOTIFY_CB;
+	eve_data->eve_cb = cb_fun;
+	eve_data->wake = wake;
+	eve_data->agent_data = data;
+
+	hash_add(reg_driver_map, &eve_data->hentry, key);
+
+	return 0;
+}
+
+static int xlnx_add_cb_for_suspend(event_cb_func_t cb_fun, void *data)
+{
+	struct registered_event_data *eve_data;
+
+	/* Check for existing entry in hash table for given cb_type */
+	hash_for_each_possible(reg_driver_map, eve_data, hentry, PM_INIT_SUSPEND_CB) {
+		if (eve_data->cb_type == PM_INIT_SUSPEND_CB) {
+			pr_err("Found as already registered\n");
+			return -EINVAL;
+		}
+	}
+
+	/* Add new entry if not present */
+	eve_data = kmalloc(sizeof(*eve_data), GFP_KERNEL);
+	if (!eve_data)
+		return -ENOMEM;
+
+	eve_data->key = 0;
+	eve_data->cb_type = PM_INIT_SUSPEND_CB;
+	eve_data->eve_cb = cb_fun;
+	eve_data->agent_data = data;
+
+	hash_add(reg_driver_map, &eve_data->hentry, PM_INIT_SUSPEND_CB);
+
+	return 0;
+}
+
+static int xlnx_remove_cb_for_suspend(event_cb_func_t cb_fun)
+{
+	bool is_callback_found = false;
+	struct registered_event_data *eve_data;
+
+	/* Check for existing entry in hash table for given cb_type */
+	hash_for_each_possible(reg_driver_map, eve_data, hentry, PM_INIT_SUSPEND_CB) {
+		if (eve_data->cb_type == PM_INIT_SUSPEND_CB &&
+		    eve_data->eve_cb == cb_fun) {
+			is_callback_found = true;
+			/* remove an object from a hashtable */
+			hash_del(&eve_data->hentry);
+			kfree(eve_data);
+		}
+	}
+	if (!is_callback_found) {
+		pr_warn("Didn't find any registered callback for suspend event\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int xlnx_remove_cb_for_notify_event(const u32 node_id, const u32 event,
+					   event_cb_func_t cb_fun)
+{
+	bool is_callback_found = false;
+	struct registered_event_data *eve_data;
+	u64 key = ((u64)node_id << 32U) | (u64)event;
+
+	/* Check for existing entry in hash table for given key id */
+	hash_for_each_possible(reg_driver_map, eve_data, hentry, key) {
+		if (eve_data->key == key &&
+		    eve_data->eve_cb == cb_fun) {
+			is_callback_found = true;
+			/* remove an object from a hashtable */
+			hash_del(&eve_data->hentry);
+			kfree(eve_data);
+		}
+	}
+	if (!is_callback_found) {
+		pr_warn("Didn't find any registered callback for 0x%x 0x%x\n",
+			node_id, event);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * xlnx_register_event() - Register for the event.
+ * @cb_type:	Type of callback from pm_api_cb_id,
+ *			PM_NOTIFY_CB - for Error Events,
+ *			PM_INIT_SUSPEND_CB - for suspend callback.
+ * @node_id:	Node-Id related to event.
+ * @event:	Event Mask for the Error Event.
+ * @wake:	Flag specifying whether the subsystem should be woken upon
+ *		event notification.
+ * @cb_fun:	Function pointer to store the callback function.
+ * @data:	Pointer for the driver instance.
+ *
+ * Return:	Returns 0 on successful registration else error code.
+ */
+int xlnx_register_event(const enum pm_api_cb_id cb_type, const u32 node_id, const u32 event,
+			const bool wake, event_cb_func_t cb_fun, void *data)
+{
+	int ret = 0;
+	u32 eve;
+	int pos;
+
+	if (event_manager_availability)
+		return event_manager_availability;
+
+	if (cb_type != PM_NOTIFY_CB && cb_type != PM_INIT_SUSPEND_CB) {
+		pr_err("%s() Unsupported Callback 0x%x\n", __func__, cb_type);
+		return -EINVAL;
+	}
+
+	if (!cb_fun)
+		return -EFAULT;
+
+	if (cb_type == PM_INIT_SUSPEND_CB) {
+		ret = xlnx_add_cb_for_suspend(cb_fun, data);
+	} else {
+		if (!xlnx_is_error_event(node_id)) {
+			/* Add entry for Node-Id/Event in hash table */
+			ret = xlnx_add_cb_for_notify_event(node_id, event, wake, cb_fun, data);
+		} else {
+			/* Add into Hash table */
+			for (pos = 0; pos < MAX_BITS; pos++) {
+				eve = event & (1 << pos);
+				if (!eve)
+					continue;
+
+				/* Add entry for Node-Id/Eve in hash table */
+				ret = xlnx_add_cb_for_notify_event(node_id, eve, wake, cb_fun,
+								   data);
+				/* Break the loop if got error */
+				if (ret)
+					break;
+			}
+			if (ret) {
+				/* Skip the Event for which got the error */
+				pos--;
+				/* Remove registered(during this call) event from hash table */
+				for ( ; pos >= 0; pos--) {
+					eve = event & (1 << pos);
+					if (!eve)
+						continue;
+					xlnx_remove_cb_for_notify_event(node_id, eve, cb_fun);
+				}
+			}
+		}
+
+		if (ret) {
+			pr_err("%s() failed for 0x%x and 0x%x: %d\r\n", __func__, node_id,
+			       event, ret);
+			return ret;
+		}
+
+		/* Register for Node-Id/Event combination in firmware */
+		ret = zynqmp_pm_register_notifier(node_id, event, wake, true);
+		if (ret) {
+			pr_err("%s() failed for 0x%x and 0x%x: %d\r\n", __func__, node_id,
+			       event, ret);
+			/* Remove already registered event from hash table */
+			if (xlnx_is_error_event(node_id)) {
+				for (pos = 0; pos < MAX_BITS; pos++) {
+					eve = event & (1 << pos);
+					if (!eve)
+						continue;
+					xlnx_remove_cb_for_notify_event(node_id, eve, cb_fun);
+				}
+			} else {
+				xlnx_remove_cb_for_notify_event(node_id, event, cb_fun);
+			}
+			return ret;
+		}
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(xlnx_register_event);
+
+/**
+ * xlnx_unregister_event() - Unregister for the event.
+ * @cb_type:	Type of callback from pm_api_cb_id,
+ *			PM_NOTIFY_CB - for Error Events,
+ *			PM_INIT_SUSPEND_CB - for suspend callback.
+ * @node_id:	Node-Id related to event.
+ * @event:	Event Mask for the Error Event.
+ * @cb_fun:	Function pointer of callback function.
+ *
+ * Return:	Returns 0 on successful unregistration else error code.
+ */
+int xlnx_unregister_event(const enum pm_api_cb_id cb_type, const u32 node_id, const u32 event,
+			  event_cb_func_t cb_fun)
+{
+	int ret;
+	u32 eve, pos;
+
+	if (event_manager_availability)
+		return event_manager_availability;
+
+	if (cb_type != PM_NOTIFY_CB && cb_type != PM_INIT_SUSPEND_CB) {
+		pr_err("%s() Unsupported Callback 0x%x\n", __func__, cb_type);
+		return -EINVAL;
+	}
+
+	if (!cb_fun)
+		return -EFAULT;
+
+	if (cb_type == PM_INIT_SUSPEND_CB) {
+		ret = xlnx_remove_cb_for_suspend(cb_fun);
+	} else {
+		/* Remove Node-Id/Event from hash table */
+		if (!xlnx_is_error_event(node_id)) {
+			xlnx_remove_cb_for_notify_event(node_id, event, cb_fun);
+		} else {
+			for (pos = 0; pos < MAX_BITS; pos++) {
+				eve = event & (1 << pos);
+				if (!eve)
+					continue;
+
+				xlnx_remove_cb_for_notify_event(node_id, eve, cb_fun);
+			}
+		}
+
+		/* Un-register for Node-Id/Event combination */
+		ret = zynqmp_pm_register_notifier(node_id, event, false, false);
+		if (ret) {
+			pr_err("%s() failed for 0x%x and 0x%x: %d\n",
+			       __func__, node_id, event, ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(xlnx_unregister_event);
+
+static void xlnx_call_suspend_cb_handler(const u32 *payload)
+{
+	bool is_callback_found = false;
+	struct registered_event_data *eve_data;
+	u32 cb_type = payload[0];
+
+	/* Check for existing entry in hash table for given cb_type */
+	hash_for_each_possible(reg_driver_map, eve_data, hentry, cb_type) {
+		if (eve_data->cb_type == cb_type) {
+			eve_data->eve_cb(&payload[0], eve_data->agent_data);
+			is_callback_found = true;
+		}
+	}
+	if (!is_callback_found)
+		pr_warn("Didn't find any registered callback for suspend event\n");
+}
+
+static void xlnx_call_notify_cb_handler(const u32 *payload)
+{
+	bool is_callback_found = false;
+	struct registered_event_data *eve_data;
+	u64 key = ((u64)payload[1] << 32U) | (u64)payload[2];
+	int ret;
+
+	/* Check for existing entry in hash table for given key id */
+	hash_for_each_possible(reg_driver_map, eve_data, hentry, key) {
+		if (eve_data->key == key) {
+			eve_data->eve_cb(&payload[0], eve_data->agent_data);
+			is_callback_found = true;
+
+			/* re register with firmware to get future events */
+			ret = zynqmp_pm_register_notifier(payload[1], payload[2],
+							  eve_data->wake, true);
+			if (ret) {
+				pr_err("%s() failed for 0x%x and 0x%x: %d\r\n", __func__,
+				       payload[1], payload[2], ret);
+				/* Remove already registered event from hash table */
+				xlnx_remove_cb_for_notify_event(payload[1], payload[2],
+								eve_data->eve_cb);
+			}
+		}
+	}
+	if (!is_callback_found)
+		pr_warn("Didn't find any registered callback for 0x%x 0x%x\n",
+			payload[1], payload[2]);
+}
+
+static void xlnx_get_event_callback_data(u32 *buf)
+{
+	zynqmp_pm_invoke_fn(GET_CALLBACK_DATA, 0, 0, 0, 0, 0, buf);
+}
+
+static irqreturn_t xlnx_event_handler(int irq, void *dev_id)
+{
+	u32 cb_type, node_id, event, pos;
+	u32 payload[CB_MAX_PAYLOAD_SIZE] = {0};
+	u32 event_data[CB_MAX_PAYLOAD_SIZE] = {0};
+
+	/* Get event data */
+	xlnx_get_event_callback_data(payload);
+
+	/* First element is callback type, others are callback arguments */
+	cb_type = payload[0];
+
+	if (cb_type == PM_NOTIFY_CB) {
+		node_id = payload[1];
+		event = payload[2];
+		if (!xlnx_is_error_event(node_id)) {
+			xlnx_call_notify_cb_handler(payload);
+		} else {
+			/*
+			 * Each call back function expecting payload as an input arguments.
+			 * We can get multiple error events as in one call back through error
+			 * mask. So payload[2] may can contain multiple error events.
+			 * In reg_driver_map database we store data in the combination of single
+			 * node_id-error combination.
+			 * So coping the payload message into event_data and update the
+			 * event_data[2] with Error Mask for single error event and use
+			 * event_data as input argument for registered call back function.
+			 *
+			 */
+			memcpy(event_data, payload, (4 * CB_MAX_PAYLOAD_SIZE));
+			/* Support Multiple Error Event */
+			for (pos = 0; pos < MAX_BITS; pos++) {
+				if ((0 == (event & (1 << pos))))
+					continue;
+				event_data[2] = (event & (1 << pos));
+				xlnx_call_notify_cb_handler(event_data);
+			}
+		}
+	} else if (cb_type == PM_INIT_SUSPEND_CB) {
+		xlnx_call_suspend_cb_handler(payload);
+	} else {
+		pr_err("%s() Unsupported Callback %d\n", __func__, cb_type);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int xlnx_event_cpuhp_start(unsigned int cpu)
+{
+	enable_percpu_irq(virq_sgi, IRQ_TYPE_NONE);
+
+	return 0;
+}
+
+static int xlnx_event_cpuhp_down(unsigned int cpu)
+{
+	disable_percpu_irq(virq_sgi);
+
+	return 0;
+}
+
+static void xlnx_disable_percpu_irq(void *data)
+{
+	disable_percpu_irq(virq_sgi);
+}
+
+static int xlnx_event_init_sgi(struct platform_device *pdev)
+{
+	int ret = 0;
+	int cpu = smp_processor_id();
+	/*
+	 * IRQ related structures are used for the following:
+	 * for each SGI interrupt ensure its mapped by GIC IRQ domain
+	 * and that each corresponding linux IRQ for the HW IRQ has
+	 * a handler for when receiving an interrupt from the remote
+	 * processor.
+	 */
+	struct irq_domain *domain;
+	struct irq_fwspec sgi_fwspec;
+	struct device_node *interrupt_parent = NULL;
+	struct device *parent = pdev->dev.parent;
+
+	/* Find GIC controller to map SGIs. */
+	interrupt_parent = of_irq_find_parent(parent->of_node);
+	if (!interrupt_parent) {
+		dev_err(&pdev->dev, "Failed to find property for Interrupt parent\n");
+		return -EINVAL;
+	}
+
+	/* Each SGI needs to be associated with GIC's IRQ domain. */
+	domain = irq_find_host(interrupt_parent);
+	of_node_put(interrupt_parent);
+
+	/* Each mapping needs GIC domain when finding IRQ mapping. */
+	sgi_fwspec.fwnode = domain->fwnode;
+
+	/*
+	 * When irq domain looks at mapping each arg is as follows:
+	 * 3 args for: interrupt type (SGI), interrupt # (set later), type
+	 */
+	sgi_fwspec.param_count = 1;
+
+	/* Set SGI's hwirq */
+	sgi_fwspec.param[0] = sgi_num;
+	virq_sgi = irq_create_fwspec_mapping(&sgi_fwspec);
+
+	per_cpu(cpu_number1, cpu) = cpu;
+	ret = request_percpu_irq(virq_sgi, xlnx_event_handler, "xlnx_event_mgmt",
+				 &cpu_number1);
+	WARN_ON(ret);
+	if (ret) {
+		irq_dispose_mapping(virq_sgi);
+		return ret;
+	}
+
+	irq_to_desc(virq_sgi);
+	irq_set_status_flags(virq_sgi, IRQ_PER_CPU);
+
+	return ret;
+}
+
+static void xlnx_event_cleanup_sgi(struct platform_device *pdev)
+{
+	int cpu = smp_processor_id();
+
+	per_cpu(cpu_number1, cpu) = cpu;
+
+	cpuhp_remove_state(CPUHP_AP_ONLINE_DYN);
+
+	on_each_cpu(xlnx_disable_percpu_irq, NULL, 1);
+
+	irq_clear_status_flags(virq_sgi, IRQ_PER_CPU);
+	free_percpu_irq(virq_sgi, &cpu_number1);
+	irq_dispose_mapping(virq_sgi);
+}
+
+static int xlnx_event_manager_probe(struct platform_device *pdev)
+{
+	int ret;
+
+	ret = zynqmp_pm_feature(PM_REGISTER_NOTIFIER);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Feature check failed with %d\n", ret);
+		return ret;
+	}
+
+	if ((ret & FIRMWARE_VERSION_MASK) <
+	    REGISTER_NOTIFIER_FIRMWARE_VERSION) {
+		dev_err(&pdev->dev, "Register notifier version error. Expected Firmware: v%d - Found: v%d\n",
+			REGISTER_NOTIFIER_FIRMWARE_VERSION,
+			ret & FIRMWARE_VERSION_MASK);
+		return -EOPNOTSUPP;
+	}
+
+	/* Initialize the SGI */
+	ret = xlnx_event_init_sgi(pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "SGI Init has been failed with %d\n", ret);
+		return ret;
+	}
+
+	/* Setup function for the CPU hot-plug cases */
+	cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "soc/event:starting",
+			  xlnx_event_cpuhp_start, xlnx_event_cpuhp_down);
+
+	ret = zynqmp_pm_register_sgi(sgi_num, 0);
+	if (ret) {
+		if (ret == -ENOTSUPP)
+			dev_info(&pdev->dev, "PM firmware event notification not supported\n");
+		else
+			dev_err(&pdev->dev, "SGI %d registration failed, err %d\n",
+				sgi_num, ret);
+
+		xlnx_event_cleanup_sgi(pdev);
+		return ret;
+	}
+
+	event_manager_availability = 0;
+
+	dev_info(&pdev->dev, "SGI %d Registered over ATF\n", sgi_num);
+	dev_info(&pdev->dev, "Xilinx Event Management driver probed\n");
+
+	return ret;
+}
+
+static int xlnx_event_manager_remove(struct platform_device *pdev)
+{
+	int i;
+	struct registered_event_data *eve_data;
+	struct hlist_node *tmp;
+	int ret;
+
+	hash_for_each_safe(reg_driver_map, i, tmp, eve_data, hentry) {
+		hash_del(&eve_data->hentry);
+		kfree(eve_data);
+	}
+
+	ret = zynqmp_pm_register_sgi(0, 1);
+	if (ret)
+		dev_err(&pdev->dev, "SGI unregistration over ATF failed with %d\n", ret);
+
+	xlnx_event_cleanup_sgi(pdev);
+
+	event_manager_availability = -EACCES;
+
+	return ret;
+}
+
+static struct platform_driver xlnx_event_manager_driver = {
+	.probe = xlnx_event_manager_probe,
+	.remove = xlnx_event_manager_remove,
+	.driver = {
+		.name = "xlnx_event_manager",
+	},
+};
+module_param(sgi_num, uint, 0);
+module_platform_driver(xlnx_event_manager_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/xilinx/zynqmp_pm_domains.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/xilinx/zynqmp_pm_domains.c
@@ -152,11 +152,17 @@
 static int zynqmp_gpd_attach_dev(struct generic_pm_domain *domain,
 				 struct device *dev)
 {
+	struct device_link *link;
 	int ret;
 	struct zynqmp_pm_domain *pd;
 
 	pd = container_of(domain, struct zynqmp_pm_domain, gpd);
 
+	link = device_link_add(dev, &domain->dev, DL_FLAG_SYNC_STATE_ONLY);
+	if (!link)
+		dev_dbg(&domain->dev, "failed to create device link for %s\n",
+			dev_name(dev));
+
 	/* If this is not the first device to attach there is nothing to do */
 	if (domain->device_count)
 		return 0;
@@ -226,7 +232,7 @@
 			goto done;
 	}
 
-	/**
+	/*
 	 * Add index in empty node_id of power domain list as no existing
 	 * power domain found for current index.
 	 */
@@ -299,9 +305,19 @@
 	return 0;
 }
 
+static void zynqmp_gpd_sync_state(struct device *dev)
+{
+	int ret;
+
+	ret = zynqmp_pm_init_finalize();
+	if (ret)
+		dev_warn(dev, "failed to release power management to firmware\n");
+}
+
 static struct platform_driver zynqmp_power_domain_driver = {
 	.driver	= {
 		.name = "zynqmp_power_controller",
+		.sync_state = zynqmp_gpd_sync_state,
 	},
 	.probe = zynqmp_gpd_probe,
 	.remove = zynqmp_gpd_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soc/xilinx/zynqmp_power.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soc/xilinx/zynqmp_power.c
@@ -16,6 +16,7 @@
 #include <linux/suspend.h>
 
 #include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/firmware/xlnx-event-manager.h>
 #include <linux/mailbox/zynqmp-ipi-message.h>
 
 /**
@@ -30,6 +31,7 @@
 
 static struct zynqmp_pm_work_struct *zynqmp_pm_init_suspend_work;
 static struct mbox_chan *rx_chan;
+static bool event_registered;
 
 enum pm_suspend_mode {
 	PM_SUSPEND_MODE_FIRST = 0,
@@ -46,15 +48,22 @@
 
 static enum pm_suspend_mode suspend_mode = PM_SUSPEND_MODE_STD;
 
-enum pm_api_cb_id {
-	PM_INIT_SUSPEND_CB = 30,
-	PM_ACKNOWLEDGE_CB,
-	PM_NOTIFY_CB,
-};
-
 static void zynqmp_pm_get_callback_data(u32 *buf)
 {
-	zynqmp_pm_invoke_fn(GET_CALLBACK_DATA, 0, 0, 0, 0, buf);
+	zynqmp_pm_invoke_fn(GET_CALLBACK_DATA, 0, 0, 0, 0, 0, buf);
+}
+
+static void suspend_event_callback(const u32 *payload, void *data)
+{
+	/* First element is callback API ID, others are callback arguments */
+	if (work_pending(&zynqmp_pm_init_suspend_work->callback_work))
+		return;
+
+	/* Copy callback arguments into work's structure */
+	memcpy(zynqmp_pm_init_suspend_work->args, &payload[1],
+	       sizeof(zynqmp_pm_init_suspend_work->args));
+
+	queue_work(system_unbound_wq, &zynqmp_pm_init_suspend_work->callback_work);
 }
 
 static irqreturn_t zynqmp_pm_isr(int irq, void *data)
@@ -73,8 +82,8 @@
 			pm_suspend(PM_SUSPEND_MEM);
 			break;
 		default:
-			pr_err("%s Unsupported InitSuspendCb reason "
-				"code %d\n", __func__, payload[1]);
+			pr_err("%s Unsupported InitSuspendCb reason code %d\n",
+			       __func__, payload[1]);
 		}
 	}
 
@@ -178,14 +187,40 @@
 	u32 pm_api_version;
 	struct mbox_client *client;
 
-	zynqmp_pm_init_finalize();
-	zynqmp_pm_get_api_version(&pm_api_version);
+	ret = zynqmp_pm_get_api_version(&pm_api_version);
+	if (ret)
+		return ret;
 
 	/* Check PM API version number */
 	if (pm_api_version < ZYNQMP_PM_VERSION)
 		return -ENODEV;
 
-	if (of_find_property(pdev->dev.of_node, "mboxes", NULL)) {
+	/*
+	 * First try to use Xilinx Event Manager by registering suspend_event_callback
+	 * for suspend/shutdown event.
+	 * If xlnx_register_event() returns -EACCES (Xilinx Event Manager
+	 * is not available to use) or -ENODEV(Xilinx Event Manager not compiled),
+	 * then use ipi-mailbox or interrupt method.
+	 */
+	ret = xlnx_register_event(PM_INIT_SUSPEND_CB, 0, 0, false,
+				  suspend_event_callback, NULL);
+	if (!ret) {
+		zynqmp_pm_init_suspend_work = devm_kzalloc(&pdev->dev,
+							   sizeof(struct zynqmp_pm_work_struct),
+							   GFP_KERNEL);
+		if (!zynqmp_pm_init_suspend_work) {
+			xlnx_unregister_event(PM_INIT_SUSPEND_CB, 0, 0,
+					      suspend_event_callback);
+			return -ENOMEM;
+		}
+		event_registered = true;
+
+		INIT_WORK(&zynqmp_pm_init_suspend_work->callback_work,
+			  zynqmp_pm_init_suspend_work_fn);
+	} else if (ret != -EACCES && ret != -ENODEV) {
+		dev_err(&pdev->dev, "Failed to Register with Xilinx Event manager %d\n", ret);
+		return ret;
+	} else if (of_find_property(pdev->dev.of_node, "mboxes", NULL)) {
 		zynqmp_pm_init_suspend_work =
 			devm_kzalloc(&pdev->dev,
 				     sizeof(struct zynqmp_pm_work_struct),
@@ -218,8 +253,8 @@
 						dev_name(&pdev->dev),
 						&pdev->dev);
 		if (ret) {
-			dev_err(&pdev->dev, "devm_request_threaded_irq '%d' "
-					    "failed with %d\n", irq, ret);
+			dev_err(&pdev->dev, "devm_request_threaded_irq '%d' failed with %d\n",
+				irq, ret);
 			return ret;
 		}
 	} else {
@@ -229,6 +264,10 @@
 
 	ret = sysfs_create_file(&pdev->dev.kobj, &dev_attr_suspend_mode.attr);
 	if (ret) {
+		if (event_registered) {
+			xlnx_unregister_event(PM_INIT_SUSPEND_CB, 0, 0, suspend_event_callback);
+			event_registered = false;
+		}
 		dev_err(&pdev->dev, "unable to create sysfs interface\n");
 		return ret;
 	}
@@ -239,6 +278,8 @@
 static int zynqmp_pm_remove(struct platform_device *pdev)
 {
 	sysfs_remove_file(&pdev->dev.kobj, &dev_attr_suspend_mode.attr);
+	if (event_registered)
+		xlnx_unregister_event(PM_INIT_SUSPEND_CB, 0, 0, suspend_event_callback);
 
 	if (!rx_chan)
 		mbox_free_channel(rx_chan);
@@ -246,6 +287,23 @@
 	return 0;
 }
 
+static int __init do_init_finalize(void)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "xlnx,zynqmp");
+	if (!np) {
+		np = of_find_compatible_node(NULL, NULL, "xlnx,versal");
+		if (!np)
+			return 0;
+	}
+	of_node_put(np);
+
+	return zynqmp_pm_init_finalize();
+}
+
+late_initcall_sync(do_init_finalize);
+
 static const struct of_device_id pm_of_match[] = {
 	{ .compatible = "xlnx,zynqmp-power", },
 	{ /* end of table */ },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/bus.c
@@ -7,6 +7,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/soundwire/sdw.h>
+#include <linux/soundwire/sdw_type.h>
 #include "bus.h"
 #include "sysfs_local.h"
 
@@ -827,8 +828,8 @@
 			"%s: initializing enumeration and init completion for Slave %d\n",
 			__func__, slave->dev_num);
 
-		init_completion(&slave->enumeration_complete);
-		init_completion(&slave->initialization_complete);
+		reinit_completion(&slave->enumeration_complete);
+		reinit_completion(&slave->initialization_complete);
 
 	} else if ((status == SDW_SLAVE_ATTACHED) &&
 		   (slave->status == SDW_SLAVE_UNATTACHED)) {
@@ -836,7 +837,7 @@
 			"%s: signaling enumeration completion for Slave %d\n",
 			__func__, slave->dev_num);
 
-		complete(&slave->enumeration_complete);
+		complete_all(&slave->enumeration_complete);
 	}
 	slave->status = status;
 	mutex_unlock(&bus->bus_lock);
@@ -846,15 +847,21 @@
 				       enum sdw_clk_stop_mode mode,
 				       enum sdw_clk_stop_type type)
 {
-	int ret;
+	int ret = 0;
 
-	if (slave->ops && slave->ops->clk_stop) {
-		ret = slave->ops->clk_stop(slave, mode, type);
-		if (ret < 0)
-			return ret;
+	mutex_lock(&slave->sdw_dev_lock);
+
+	if (slave->probed)  {
+		struct device *dev = &slave->dev;
+		struct sdw_driver *drv = drv_to_sdw_driver(dev->driver);
+
+		if (drv->ops && drv->ops->clk_stop)
+			ret = drv->ops->clk_stop(slave, mode, type);
 	}
 
-	return 0;
+	mutex_unlock(&slave->sdw_dev_lock);
+
+	return ret;
 }
 
 static int sdw_slave_clk_stop_prepare(struct sdw_slave *slave,
@@ -1110,7 +1117,7 @@
 	if (!simple_clk_stop) {
 		ret = sdw_bus_wait_for_clk_prep_deprep(bus, SDW_BROADCAST_DEV_NUM);
 		if (ret < 0)
-			dev_warn(&slave->dev, "clock stop deprepare wait failed:%d\n", ret);
+			dev_warn(bus->dev, "clock stop deprepare wait failed:%d\n", ret);
 	}
 
 	list_for_each_entry(slave, &bus->slaves, node) {
@@ -1616,14 +1623,24 @@
 		}
 
 		/* Update the Slave driver */
-		if (slave_notify && slave->ops &&
-		    slave->ops->interrupt_callback) {
-			slave_intr.sdca_cascade = sdca_cascade;
-			slave_intr.control_port = clear;
-			memcpy(slave_intr.port, &port_status,
-			       sizeof(slave_intr.port));
+		if (slave_notify) {
+			mutex_lock(&slave->sdw_dev_lock);
+
+			if (slave->probed) {
+				struct device *dev = &slave->dev;
+				struct sdw_driver *drv = drv_to_sdw_driver(dev->driver);
+
+				if (drv->ops && drv->ops->interrupt_callback) {
+					slave_intr.sdca_cascade = sdca_cascade;
+					slave_intr.control_port = clear;
+					memcpy(slave_intr.port, &port_status,
+					       sizeof(slave_intr.port));
+
+					drv->ops->interrupt_callback(slave, &slave_intr);
+				}
+			}
 
-			slave->ops->interrupt_callback(slave, &slave_intr);
+			mutex_unlock(&slave->sdw_dev_lock);
 		}
 
 		/* Ack interrupt */
@@ -1697,29 +1714,21 @@
 static int sdw_update_slave_status(struct sdw_slave *slave,
 				   enum sdw_slave_status status)
 {
-	unsigned long time;
+	int ret = 0;
 
-	if (!slave->probed) {
-		/*
-		 * the slave status update is typically handled in an
-		 * interrupt thread, which can race with the driver
-		 * probe, e.g. when a module needs to be loaded.
-		 *
-		 * make sure the probe is complete before updating
-		 * status.
-		 */
-		time = wait_for_completion_timeout(&slave->probe_complete,
-				msecs_to_jiffies(DEFAULT_PROBE_TIMEOUT));
-		if (!time) {
-			dev_err(&slave->dev, "Probe not complete, timed out\n");
-			return -ETIMEDOUT;
-		}
+	mutex_lock(&slave->sdw_dev_lock);
+
+	if (slave->probed) {
+		struct device *dev = &slave->dev;
+		struct sdw_driver *drv = drv_to_sdw_driver(dev->driver);
+
+		if (drv->ops && drv->ops->update_status)
+			ret = drv->ops->update_status(slave, status);
 	}
 
-	if (!slave->ops || !slave->ops->update_status)
-		return 0;
+	mutex_unlock(&slave->sdw_dev_lock);
 
-	return slave->ops->update_status(slave, status);
+	return ret;
 }
 
 /**
@@ -1831,7 +1840,19 @@
 				"%s: signaling initialization completion for Slave %d\n",
 				__func__, slave->dev_num);
 
-			complete(&slave->initialization_complete);
+			complete_all(&slave->initialization_complete);
+
+			/*
+			 * If the manager became pm_runtime active, the peripherals will be
+			 * restarted and attach, but their pm_runtime status may remain
+			 * suspended. If the 'update_slave_status' callback initiates
+			 * any sort of deferred processing, this processing would not be
+			 * cancelled on pm_runtime suspend.
+			 * To avoid such zombie states, we queue a request to resume.
+			 * This would be a no-op in case the peripheral was being resumed
+			 * by e.g. the ALSA/ASoC framework.
+			 */
+			pm_request_resume(&slave->dev);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/bus_type.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/bus_type.c
@@ -98,8 +98,6 @@
 	if (!id)
 		return -ENODEV;
 
-	slave->ops = drv->ops;
-
 	/*
 	 * attach to power domain but don't turn on (last arg)
 	 */
@@ -112,14 +110,17 @@
 		name = drv->name;
 		if (!name)
 			name = drv->driver.name;
+
 		dev_err(dev, "Probe of %s failed: %d\n", name, ret);
 		dev_pm_domain_detach(dev, false);
 		return ret;
 	}
 
+	mutex_lock(&slave->sdw_dev_lock);
+
 	/* device is probed so let's read the properties now */
-	if (slave->ops && slave->ops->read_prop)
-		slave->ops->read_prop(slave);
+	if (drv->ops && drv->ops->read_prop)
+		drv->ops->read_prop(slave);
 
 	/* init the sysfs as we have properties now */
 	ret = sdw_slave_sysfs_init(slave);
@@ -139,7 +140,19 @@
 					     slave->prop.clk_stop_timeout);
 
 	slave->probed = true;
-	complete(&slave->probe_complete);
+
+	/*
+	 * if the probe happened after the bus was started, notify the codec driver
+	 * of the current hardware status to e.g. start the initialization.
+	 * Errors are only logged as warnings to avoid failing the probe.
+	 */
+	if (drv->ops && drv->ops->update_status) {
+		ret = drv->ops->update_status(slave, slave->status);
+		if (ret < 0)
+			dev_warn(dev, "%s: update_status failed with status %d\n", __func__, ret);
+	}
+
+	mutex_unlock(&slave->sdw_dev_lock);
 
 	dev_dbg(dev, "probe complete\n");
 
@@ -152,6 +165,10 @@
 	struct sdw_driver *drv = drv_to_sdw_driver(dev->driver);
 	int ret = 0;
 
+	mutex_lock(&slave->sdw_dev_lock);
+	slave->probed = false;
+	mutex_unlock(&slave->sdw_dev_lock);
+
 	if (drv->remove)
 		ret = drv->remove(slave);
 
@@ -193,12 +210,8 @@
 
 	drv->driver.owner = owner;
 	drv->driver.probe = sdw_drv_probe;
-
-	if (drv->remove)
-		drv->driver.remove = sdw_drv_remove;
-
-	if (drv->shutdown)
-		drv->driver.shutdown = sdw_drv_shutdown;
+	drv->driver.remove = sdw_drv_remove;
+	drv->driver.shutdown = sdw_drv_shutdown;
 
 	return driver_register(&drv->driver);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/cadence_master.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/cadence_master.c
@@ -127,7 +127,8 @@
 
 #define CDNS_MCP_CMD_BASE			0x80
 #define CDNS_MCP_RESP_BASE			0x80
-#define CDNS_MCP_CMD_LEN			0x20
+/* FIFO can hold 8 commands */
+#define CDNS_MCP_CMD_LEN			8
 #define CDNS_MCP_CMD_WORD_LEN			0x4
 
 #define CDNS_MCP_CMD_SSP_TAG			BIT(31)
@@ -545,13 +546,39 @@
 		return SDW_CMD_IGNORED;
 	}
 
-	/* fill response */
-	for (i = 0; i < count; i++)
-		msg->buf[i + offset] = FIELD_GET(CDNS_MCP_RESP_RDATA, cdns->response_buf[i]);
+	if (msg->flags == SDW_MSG_FLAG_READ) {
+		/* fill response */
+		for (i = 0; i < count; i++)
+			msg->buf[i + offset] = FIELD_GET(CDNS_MCP_RESP_RDATA,
+							 cdns->response_buf[i]);
+	}
 
 	return SDW_CMD_OK;
 }
 
+static void cdns_read_response(struct sdw_cdns *cdns)
+{
+	u32 num_resp, cmd_base;
+	int i;
+
+	/* RX_FIFO_AVAIL can be 2 entries more than the FIFO size */
+	BUILD_BUG_ON(ARRAY_SIZE(cdns->response_buf) < CDNS_MCP_CMD_LEN + 2);
+
+	num_resp = cdns_readl(cdns, CDNS_MCP_FIFOSTAT);
+	num_resp &= CDNS_MCP_RX_FIFO_AVAIL;
+	if (num_resp > ARRAY_SIZE(cdns->response_buf)) {
+		dev_warn(cdns->dev, "RX AVAIL %d too long\n", num_resp);
+		num_resp = ARRAY_SIZE(cdns->response_buf);
+	}
+
+	cmd_base = CDNS_MCP_CMD_BASE;
+
+	for (i = 0; i < num_resp; i++) {
+		cdns->response_buf[i] = cdns_readl(cdns, cmd_base);
+		cmd_base += CDNS_MCP_CMD_WORD_LEN;
+	}
+}
+
 static enum sdw_command_response
 _cdns_xfer_msg(struct sdw_cdns *cdns, struct sdw_msg *msg, int cmd,
 	       int offset, int count, bool defer)
@@ -593,6 +620,10 @@
 		dev_err(cdns->dev, "IO transfer timed out, cmd %d device %d addr %x len %d\n",
 			cmd, msg->dev_num, msg->addr, msg->len);
 		msg->len = 0;
+
+		/* Drain anything in the RX_FIFO */
+		cdns_read_response(cdns);
+
 		return SDW_CMD_TIMEOUT;
 	}
 
@@ -761,22 +792,6 @@
  * IRQ handling
  */
 
-static void cdns_read_response(struct sdw_cdns *cdns)
-{
-	u32 num_resp, cmd_base;
-	int i;
-
-	num_resp = cdns_readl(cdns, CDNS_MCP_FIFOSTAT);
-	num_resp &= CDNS_MCP_RX_FIFO_AVAIL;
-
-	cmd_base = CDNS_MCP_CMD_BASE;
-
-	for (i = 0; i < num_resp; i++) {
-		cdns->response_buf[i] = cdns_readl(cdns, cmd_base);
-		cmd_base += CDNS_MCP_CMD_WORD_LEN;
-	}
-}
-
 static int cdns_update_slave_status(struct sdw_cdns *cdns,
 				    u64 slave_intstat)
 {
@@ -1815,7 +1830,7 @@
 
 	/* check if we found a PDI, else find in bi-directional */
 	if (!pdi)
-		pdi = cdns_find_pdi(cdns, 2, stream->num_bd, stream->bd,
+		pdi = cdns_find_pdi(cdns, 0, stream->num_bd, stream->bd,
 				    dai_id);
 
 	if (pdi) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/cadence_master.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/cadence_master.h
@@ -8,6 +8,12 @@
 #define SDW_CADENCE_GSYNC_KHZ		4 /* 4 kHz */
 #define SDW_CADENCE_GSYNC_HZ		(SDW_CADENCE_GSYNC_KHZ * 1000)
 
+/*
+ * The Cadence IP supports up to 32 entries in the FIFO, though implementations
+ * can configure the IP to have a smaller FIFO.
+ */
+#define CDNS_MCP_IP_MAX_CMD_LEN		32
+
 /**
  * struct sdw_cdns_pdi: PDI (Physical Data Interface) instance
  *
@@ -119,7 +125,12 @@
 	struct sdw_bus bus;
 	unsigned int instance;
 
-	u32 response_buf[0x80];
+	/*
+	 * The datasheet says the RX FIFO AVAIL can be 2 entries more
+	 * than the FIFO capacity, so allow for this.
+	 */
+	u32 response_buf[CDNS_MCP_IP_MAX_CMD_LEN + 2];
+
 	struct completion tx_complete;
 	struct sdw_defer *defer;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/debugfs.c
@@ -19,7 +19,7 @@
 		return;
 
 	/* create the debugfs master-N */
-	snprintf(name, sizeof(name), "master-%d", bus->link_id);
+	snprintf(name, sizeof(name), "master-%d-%d", bus->id, bus->link_id);
 	bus->debugfs = debugfs_create_dir(name, sdw_debugfs_root);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/dmi-quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/dmi-quirks.c
@@ -59,7 +59,14 @@
 	{
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "HP"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "HP Spectre x360 Convertible"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Spectre x360 Conv"),
+		},
+		.driver_data = (void *)intel_tgl_bios,
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "HP"),
+			DMI_MATCH(DMI_BOARD_NAME, "8709"),
 		},
 		.driver_data = (void *)intel_tgl_bios,
 	},
@@ -71,6 +78,14 @@
 		},
 		.driver_data = (void *)intel_tgl_bios,
 	},
+	{
+		/* quirk used for NUC15 LAPBC710 skew */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "LAPBC710"),
+		},
+		.driver_data = (void *)intel_tgl_bios,
+	},
 	{
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/intel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/intel.c
@@ -448,8 +448,8 @@
 
 		/* Clear wake status */
 		wake_sts = intel_readw(shim, SDW_SHIM_WAKESTS);
-		wake_sts |= (SDW_SHIM_WAKEEN_ENABLE << link_id);
-		intel_writew(shim, SDW_SHIM_WAKESTS_STATUS, wake_sts);
+		wake_sts |= (SDW_SHIM_WAKESTS_STATUS << link_id);
+		intel_writew(shim, SDW_SHIM_WAKESTS, wake_sts);
 	}
 	mutex_unlock(sdw->link_res->shim_lock);
 }
@@ -1065,8 +1065,8 @@
 	.prepare = intel_prepare,
 	.hw_free = intel_hw_free,
 	.shutdown = intel_shutdown,
-	.set_sdw_stream = intel_pcm_set_sdw_stream,
-	.get_sdw_stream = intel_get_sdw_stream,
+	.set_stream = intel_pcm_set_sdw_stream,
+	.get_stream = intel_get_sdw_stream,
 };
 
 static const struct snd_soc_dai_ops intel_pdm_dai_ops = {
@@ -1075,8 +1075,8 @@
 	.prepare = intel_prepare,
 	.hw_free = intel_hw_free,
 	.shutdown = intel_shutdown,
-	.set_sdw_stream = intel_pdm_set_sdw_stream,
-	.get_sdw_stream = intel_get_sdw_stream,
+	.set_stream = intel_pdm_set_sdw_stream,
+	.get_stream = intel_get_sdw_stream,
 };
 
 static const struct snd_soc_component_driver dai_component = {
@@ -1285,6 +1285,7 @@
 	cdns->msg_count = 0;
 
 	bus->link_id = auxdev->id;
+	bus->clk_stop_timeout = 1;
 
 	sdw_cdns_probe(cdns);
 
@@ -1298,6 +1299,9 @@
 	/* use generic bandwidth allocation algorithm */
 	sdw->cdns.bus.compute_params = sdw_compute_params;
 
+	/* avoid resuming from pm_runtime suspend if it's not required */
+	dev_pm_set_driver_flags(dev, DPM_FLAG_SMART_SUSPEND);
+
 	ret = sdw_bus_master_add(bus, dev, dev->fwnode);
 	if (ret) {
 		dev_err(dev, "sdw_bus_master_add fail: %d\n", ret);
@@ -1404,7 +1408,6 @@
 	ret = intel_register_dai(sdw);
 	if (ret) {
 		dev_err(dev, "DAI registration failed: %d\n", ret);
-		snd_soc_unregister_component(dev);
 		goto err_interrupt;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/qcom.c
@@ -97,7 +97,7 @@
 
 #define SWRM_SPECIAL_CMD_ID	0xF
 #define MAX_FREQ_NUM		1
-#define TIMEOUT_MS		(2 * HZ)
+#define TIMEOUT_MS		100
 #define QCOM_SWRM_MAX_RD_LEN	0x1
 #define QCOM_SDW_MAX_PORTS	14
 #define DEFAULT_CLK_FREQ	9600000
@@ -146,9 +146,10 @@
 	u32 intr_mask;
 	u8 rcmd_id;
 	u8 wcmd_id;
-	struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS];
+	/* Port numbers are 1 - 14 */
+	struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS + 1];
 	struct sdw_stream_runtime *sruntime[SWRM_MAX_DAIS];
-	enum sdw_slave_status status[SDW_MAX_DEVICES];
+	enum sdw_slave_status status[SDW_MAX_DEVICES + 1];
 	int (*reg_read)(struct qcom_swrm_ctrl *ctrl, int reg, u32 *val);
 	int (*reg_write)(struct qcom_swrm_ctrl *ctrl, int reg, int val);
 	u32 slave_status;
@@ -315,6 +316,9 @@
 	if (swrm_wait_for_wr_fifo_avail(swrm))
 		return SDW_CMD_FAIL_OTHER;
 
+	if (cmd_id == SWR_BROADCAST_CMD_ID)
+		reinit_completion(&swrm->broadcast);
+
 	/* Its assumed that write is okay as we do not get any status back */
 	swrm->reg_write(swrm, SWRM_CMD_FIFO_WR_CMD, val);
 
@@ -348,6 +352,12 @@
 
 	val = swrm_get_packed_reg_val(&swrm->rcmd_id, len, dev_addr, reg_addr);
 
+	/*
+	 * Check for outstanding cmd wrt. write fifo depth to avoid
+	 * overflow as read will also increase write fifo cnt.
+	 */
+	swrm_wait_for_wr_fifo_avail(swrm);
+
 	/* wait for FIFO RD to complete to avoid overflow */
 	usleep_range(100, 105);
 	swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val);
@@ -391,11 +401,11 @@
 
 	ctrl->reg_read(ctrl, SWRM_MCP_SLV_STATUS, &val);
 
-	for (dev_num = 0; dev_num < SDW_MAX_DEVICES; dev_num++) {
+	for (dev_num = 0; dev_num <= SDW_MAX_DEVICES; dev_num++) {
 		status = (val >> (dev_num * SWRM_MCP_SLV_STATUS_SZ));
 
 		if ((status & SWRM_MCP_SLV_STATUS_MASK) == SDW_SLAVE_ALERT) {
-			ctrl->status[dev_num] = status;
+			ctrl->status[dev_num] = status & SWRM_MCP_SLV_STATUS_MASK;
 			return dev_num;
 		}
 	}
@@ -411,7 +421,7 @@
 	ctrl->reg_read(ctrl, SWRM_MCP_SLV_STATUS, &val);
 	ctrl->slave_status = val;
 
-	for (i = 0; i < SDW_MAX_DEVICES; i++) {
+	for (i = 0; i <= SDW_MAX_DEVICES; i++) {
 		u32 s;
 
 		s = (val >> (i * 2));
@@ -451,6 +461,10 @@
 	char *buf1 = (char *)&val1, *buf2 = (char *)&val2;
 
 	for (i = 1; i <= SDW_MAX_DEVICES; i++) {
+		/* do not continue if the status is Not Present  */
+		if (!ctrl->status[i])
+			continue;
+
 		/*SCP_Devid5 - Devid 4*/
 		ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_1(i), &val1);
 
@@ -627,7 +641,7 @@
 
 	ctrl->reg_write(ctrl, SWRM_MCP_BUS_CTRL, SWRM_MCP_BUS_CLK_START);
 	/* Configure number of retries of a read/write cmd */
-	if (ctrl->version > 0x01050001) {
+	if (ctrl->version >= 0x01050001) {
 		/* Only for versions >= 1.5.1 */
 		ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CFG_ADDR,
 				SWRM_RD_WR_CMD_RETRIES |
@@ -1019,8 +1033,8 @@
 	ctrl->sruntime[dai->id] = sruntime;
 
 	for_each_rtd_codec_dais(rtd, i, codec_dai) {
-		ret = snd_soc_dai_set_sdw_stream(codec_dai, sruntime,
-						 substream->stream);
+		ret = snd_soc_dai_set_stream(codec_dai, sruntime,
+					     substream->stream);
 		if (ret < 0 && ret != -ENOTSUPP) {
 			dev_err(dai->dev, "Failed to set sdw stream on %s\n",
 				codec_dai->name);
@@ -1046,8 +1060,8 @@
 	.hw_free = qcom_swrm_hw_free,
 	.startup = qcom_swrm_startup,
 	.shutdown = qcom_swrm_shutdown,
-	.set_sdw_stream = qcom_swrm_set_sdw_stream,
-	.get_sdw_stream = qcom_swrm_get_sdw_stream,
+	.set_stream = qcom_swrm_set_sdw_stream,
+	.get_stream = qcom_swrm_get_sdw_stream,
 };
 
 static const struct snd_soc_component_driver qcom_swrm_dai_component = {
@@ -1129,6 +1143,9 @@
 	ctrl->num_dout_ports = val;
 
 	nports = ctrl->num_dout_ports + ctrl->num_din_ports;
+	if (nports > QCOM_SDW_MAX_PORTS)
+		return -EINVAL;
+
 	/* Valid port numbers are from 1-14, so mask out port 0 explicitly */
 	set_bit(0, &ctrl->dout_port_mask);
 	set_bit(0, &ctrl->din_port_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/slave.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/slave.c
@@ -12,6 +12,8 @@
 {
 	struct sdw_slave *slave = dev_to_sdw_dev(dev);
 
+	of_node_put(slave->dev.of_node);
+	mutex_destroy(&slave->sdw_dev_lock);
 	kfree(slave);
 }
 
@@ -58,9 +60,9 @@
 	init_completion(&slave->enumeration_complete);
 	init_completion(&slave->initialization_complete);
 	slave->dev_num = 0;
-	init_completion(&slave->probe_complete);
 	slave->probed = false;
 	slave->first_interrupt_done = false;
+	mutex_init(&slave->sdw_dev_lock);
 
 	for (i = 0; i < SDW_MAX_PORTS; i++)
 		init_completion(&slave->port_ready[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/soundwire/stream.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/soundwire/stream.c
@@ -13,6 +13,7 @@
 #include <linux/slab.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/soundwire/sdw.h>
+#include <linux/soundwire/sdw_type.h>
 #include <sound/soc.h>
 #include "bus.h"
 
@@ -401,20 +402,26 @@
 			    struct sdw_prepare_ch prep_ch,
 			    enum sdw_port_prep_ops cmd)
 {
-	const struct sdw_slave_ops *ops = s_rt->slave->ops;
-	int ret;
+	int ret = 0;
+	struct sdw_slave *slave = s_rt->slave;
 
-	if (ops->port_prep) {
-		ret = ops->port_prep(s_rt->slave, &prep_ch, cmd);
-		if (ret < 0) {
-			dev_err(&s_rt->slave->dev,
-				"Slave Port Prep cmd %d failed: %d\n",
-				cmd, ret);
-			return ret;
+	mutex_lock(&slave->sdw_dev_lock);
+
+	if (slave->probed) {
+		struct device *dev = &slave->dev;
+		struct sdw_driver *drv = drv_to_sdw_driver(dev->driver);
+
+		if (drv->ops && drv->ops->port_prep) {
+			ret = drv->ops->port_prep(slave, &prep_ch, cmd);
+			if (ret < 0)
+				dev_err(dev, "Slave Port Prep cmd %d failed: %d\n",
+					cmd, ret);
 		}
 	}
 
-	return 0;
+	mutex_unlock(&slave->sdw_dev_lock);
+
+	return ret;
 }
 
 static int sdw_prep_deprep_slave_ports(struct sdw_bus *bus,
@@ -578,7 +585,7 @@
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_bus *bus = m_rt->bus;
 	struct sdw_slave *slave;
-	int ret = 0;
+	int ret;
 
 	if (bus->ops->set_bus_conf) {
 		ret = bus->ops->set_bus_conf(bus, &bus->params);
@@ -589,17 +596,27 @@
 	list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
 		slave = s_rt->slave;
 
-		if (slave->ops->bus_config) {
-			ret = slave->ops->bus_config(slave, &bus->params);
-			if (ret < 0) {
-				dev_err(bus->dev, "Notify Slave: %d failed\n",
-					slave->dev_num);
-				return ret;
+		mutex_lock(&slave->sdw_dev_lock);
+
+		if (slave->probed) {
+			struct device *dev = &slave->dev;
+			struct sdw_driver *drv = drv_to_sdw_driver(dev->driver);
+
+			if (drv->ops && drv->ops->bus_config) {
+				ret = drv->ops->bus_config(slave, &bus->params);
+				if (ret < 0) {
+					dev_err(dev, "Notify Slave: %d failed\n",
+						slave->dev_num);
+					mutex_unlock(&slave->sdw_dev_lock);
+					return ret;
+				}
 			}
 		}
+
+		mutex_unlock(&slave->sdw_dev_lock);
 	}
 
-	return ret;
+	return 0;
 }
 
 /**
@@ -727,14 +744,15 @@
  * sdw_ml_sync_bank_switch: Multilink register bank switch
  *
  * @bus: SDW bus instance
+ * @multi_link: whether this is a multi-link stream with hardware-based sync
  *
  * Caller function should free the buffers on error
  */
-static int sdw_ml_sync_bank_switch(struct sdw_bus *bus)
+static int sdw_ml_sync_bank_switch(struct sdw_bus *bus, bool multi_link)
 {
 	unsigned long time_left;
 
-	if (!bus->multi_link)
+	if (!multi_link)
 		return 0;
 
 	/* Wait for completion of transfer */
@@ -830,7 +848,7 @@
 			bus->bank_switch_timeout = DEFAULT_BANK_SWITCH_TIMEOUT;
 
 		/* Check if bank switch was successful */
-		ret = sdw_ml_sync_bank_switch(bus);
+		ret = sdw_ml_sync_bank_switch(bus, multi_link);
 		if (ret < 0) {
 			dev_err(bus->dev,
 				"multi link bank switch failed: %d\n", ret);
@@ -1863,7 +1881,7 @@
 
 	/* Set stream pointer on all DAIs */
 	for_each_rtd_dais(rtd, i, dai) {
-		ret = snd_soc_dai_set_sdw_stream(dai, sdw_stream, substream->stream);
+		ret = snd_soc_dai_set_stream(dai, sdw_stream, substream->stream);
 		if (ret < 0) {
 			dev_err(rtd->dev, "failed to set stream pointer on dai %s\n", dai->name);
 			break;
@@ -1934,7 +1952,7 @@
 	/* Find stream from first CPU DAI */
 	dai = asoc_rtd_to_cpu(rtd, 0);
 
-	sdw_stream = snd_soc_dai_get_sdw_stream(dai, substream->stream);
+	sdw_stream = snd_soc_dai_get_stream(dai, substream->stream);
 
 	if (IS_ERR(sdw_stream)) {
 		dev_err(rtd->dev, "no stream found for DAI %s\n", dai->name);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/Kconfig
@@ -272,7 +272,6 @@
 	tristate "Baikal-T1 SPI driver for DW SPI core"
 	depends on MIPS_BAIKAL_T1 || COMPILE_TEST
 	select MULTIPLEXER
-	select MUX_MMIO
 	help
 	  Baikal-T1 SoC is equipped with three DW APB SSI-based MMIO SPI
 	  controllers. Two of them are pretty much normal: with IRQ, DMA,
@@ -413,6 +412,16 @@
 	  This enables support for the SPI master controller in the J-Core
 	  synthesizable, open source SoC.
 
+config SPI_LJCA
+	tristate "INTEL La Jolla Cove Adapter SPI support"
+	depends on MFD_LJCA
+	help
+	  Select this option to enable SPI driver for the INTEL
+	  La Jolla Cove Adapter (LJCA) board.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called spi-ljca.
+
 config SPI_LM70_LLP
 	tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 	depends on PARPORT
@@ -977,16 +986,26 @@
 config SPI_ZYNQ_QSPI
 	tristate "Xilinx Zynq QSPI controller"
 	depends on ARCH_ZYNQ || COMPILE_TEST
+	depends on SPI_MEM
 	help
 	  This enables support for the Zynq Quad SPI controller
 	  in master mode.
 	  This controller only supports SPI memory interface.
 
+config SPI_ZYNQ_QSPI_DUAL_STACKED
+	bool "Xilinx Zynq QSPI Dual stacked configuration"
+	depends on SPI_ZYNQ_QSPI
+	help
+	  This selects the Xilinx ZYNQ Quad SPI controller in dual stacked mode.
+	  Enable this option if your hw design is using dual stacked
+	  configuration.
+
 config SPI_ZYNQMP_GQSPI
 	tristate "Xilinx ZynqMP GQSPI controller"
-	depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
+	depends on (SPI_MEM && HAS_DMA) || COMPILE_TEST
 	help
 	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
+	  This controller only supports SPI memory interface.
 
 config SPI_AMD
 	tristate "AMD SPI controller"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/Makefile
@@ -61,6 +61,7 @@
 obj-$(CONFIG_SPI_IMX)			+= spi-imx.o
 obj-$(CONFIG_SPI_LANTIQ_SSC)		+= spi-lantiq-ssc.o
 obj-$(CONFIG_SPI_JCORE)			+= spi-jcore.o
+obj-$(CONFIG_SPI_LJCA)			+= spi-ljca.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi-lm70llp.o
 obj-$(CONFIG_SPI_LP8841_RTC)		+= spi-lp8841-rtc.o
 obj-$(CONFIG_SPI_MESON_SPICC)		+= spi-meson-spicc.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/atmel-quadspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/atmel-quadspi.c
@@ -182,7 +182,7 @@
 	case QSPI_MR:
 		return "MR";
 	case QSPI_RD:
-		return "MR";
+		return "RD";
 	case QSPI_TD:
 		return "TD";
 	case QSPI_SR:
@@ -277,6 +277,9 @@
 static bool atmel_qspi_supports_op(struct spi_mem *mem,
 				   const struct spi_mem_op *op)
 {
+	if (!spi_mem_default_supports_op(mem, op))
+		return false;
+
 	if (atmel_qspi_find_mode(op) < 0)
 		return false;
 
@@ -310,7 +313,7 @@
 		return mode;
 	ifr |= atmel_qspi_modes[mode].config;
 
-	if (op->dummy.buswidth && op->dummy.nbytes)
+	if (op->dummy.nbytes)
 		dummy_cycles = op->dummy.nbytes * 8 / op->dummy.buswidth;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-altera-dfl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-altera-dfl.c
@@ -128,9 +128,9 @@
 	struct spi_master *master;
 	struct altera_spi *hw;
 	void __iomem *base;
-	int err = -ENODEV;
+	int err;
 
-	master = spi_alloc_master(dev, sizeof(struct altera_spi));
+	master = devm_spi_alloc_master(dev, sizeof(struct altera_spi));
 	if (!master)
 		return -ENOMEM;
 
@@ -159,10 +159,9 @@
 	altera_spi_init_master(master);
 
 	err = devm_spi_register_master(dev, master);
-	if (err) {
-		dev_err(dev, "%s failed to register spi master %d\n", __func__, err);
-		goto exit;
-	}
+	if (err)
+		return dev_err_probe(dev, err, "%s failed to register spi master\n",
+				     __func__);
 
 	if (dfl_dev->revision == FME_FEATURE_REV_MAX10_SPI_N5010)
 		strscpy(board_info.modalias, "m10-n5010", SPI_NAME_SIZE);
@@ -179,9 +178,6 @@
 	}
 
 	return 0;
-exit:
-	spi_master_put(master);
-	return err;
 }
 
 static const struct dfl_device_id dfl_spi_altera_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-amd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-amd.c
@@ -28,6 +28,7 @@
 #define AMD_SPI_RX_COUNT_REG	0x4B
 #define AMD_SPI_STATUS_REG	0x4C
 
+#define AMD_SPI_FIFO_SIZE	70
 #define AMD_SPI_MEM_SIZE	200
 
 /* M_CMD OP codes for SPI */
@@ -245,6 +246,11 @@
 	return 0;
 }
 
+static size_t amd_spi_max_transfer_size(struct spi_device *spi)
+{
+	return AMD_SPI_FIFO_SIZE;
+}
+
 static int amd_spi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -275,6 +281,8 @@
 	master->flags = SPI_MASTER_HALF_DUPLEX;
 	master->setup = amd_spi_master_setup;
 	master->transfer_one_message = amd_spi_master_transfer;
+	master->max_transfer_size = amd_spi_max_transfer_size;
+	master->max_message_size = amd_spi_max_transfer_size;
 
 	/* Register the controller with SPI framework */
 	err = devm_spi_register_master(dev, master);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-armada-3700.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-armada-3700.c
@@ -901,7 +901,7 @@
 	return 0;
 
 error_clk:
-	clk_disable_unprepare(spi->clk);
+	clk_unprepare(spi->clk);
 error:
 	spi_master_put(master);
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-bcm-qspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-bcm-qspi.c
@@ -19,7 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
-#include <linux/spi/spi-mem.h>
+#include <linux/mtd/spi-nor.h>
 #include <linux/sysfs.h>
 #include <linux/types.h>
 #include "spi-bcm-qspi.h"
@@ -395,7 +395,8 @@
 	if (addrlen == BSPI_ADDRLEN_4BYTES)
 		bpp = BSPI_BPP_ADDR_SELECT_MASK;
 
-	bpp |= (op->dummy.nbytes * 8) / op->dummy.buswidth;
+	if (op->dummy.nbytes)
+		bpp |= (op->dummy.nbytes * 8) / op->dummy.buswidth;
 
 	switch (width) {
 	case SPI_NBITS_SINGLE:
@@ -551,7 +552,7 @@
 	u32 rd = 0;
 	u32 wr = 0;
 
-	if (qspi->base[CHIP_SELECT]) {
+	if (cs >= 0 && qspi->base[CHIP_SELECT]) {
 		rd = bcm_qspi_read(qspi, CHIP_SELECT, 0);
 		wr = (rd & ~0xff) | (1 << cs);
 		if (rd == wr)
@@ -1032,7 +1033,7 @@
 	addr = op->addr.val;
 	len = op->data.nbytes;
 
-	if (bcm_qspi_bspi_ver_three(qspi) == true) {
+	if (has_bspi(qspi) && bcm_qspi_bspi_ver_three(qspi) == true) {
 		/*
 		 * The address coming into this function is a raw flash offset.
 		 * But for BSPI <= V3, we need to convert it to a remapped BSPI
@@ -1048,10 +1049,10 @@
 
 	/* non-aligned and very short transfers are handled by MSPI */
 	if (!IS_ALIGNED((uintptr_t)addr, 4) || !IS_ALIGNED((uintptr_t)buf, 4) ||
-	    len < 4)
+	    len < 4 || op->cmd.opcode == SPINOR_OP_RDSFDP)
 		mspi_read = true;
 
-	if (mspi_read)
+	if (!has_bspi(qspi) || mspi_read)
 		return bcm_qspi_mspi_exec_mem_op(spi, op);
 
 	ret = bcm_qspi_bspi_set_mode(qspi, op, 0);
@@ -1369,13 +1370,9 @@
 		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 						   "mspi");
 
-	if (res) {
-		qspi->base[MSPI]  = devm_ioremap_resource(dev, res);
-		if (IS_ERR(qspi->base[MSPI]))
-			return PTR_ERR(qspi->base[MSPI]);
-	} else {
-		return 0;
-	}
+	qspi->base[MSPI]  = devm_ioremap_resource(dev, res);
+	if (IS_ERR(qspi->base[MSPI]))
+		return PTR_ERR(qspi->base[MSPI]);
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "bspi");
 	if (res) {
@@ -1460,7 +1457,7 @@
 					       &qspi->dev_ids[val]);
 			if (ret < 0) {
 				dev_err(&pdev->dev, "IRQ %s not found\n", name);
-				goto qspi_probe_err;
+				goto qspi_unprepare_err;
 			}
 
 			qspi->dev_ids[val].dev = qspi;
@@ -1475,7 +1472,7 @@
 	if (!num_ints) {
 		dev_err(&pdev->dev, "no IRQs registered, cannot init driver\n");
 		ret = -EINVAL;
-		goto qspi_probe_err;
+		goto qspi_unprepare_err;
 	}
 
 	bcm_qspi_hw_init(qspi);
@@ -1499,6 +1496,7 @@
 
 qspi_reg_err:
 	bcm_qspi_hw_uninit(qspi);
+qspi_unprepare_err:
 	clk_disable_unprepare(qspi->clk);
 qspi_probe_err:
 	kfree(qspi->dev_ids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-bcm2835.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-bcm2835.c
@@ -1138,10 +1138,14 @@
 	struct bcm2835_spi *bs = spi_controller_get_devdata(ctlr);
 
 	/* if an error occurred and we have an active dma, then terminate */
-	dmaengine_terminate_sync(ctlr->dma_tx);
-	bs->tx_dma_active = false;
-	dmaengine_terminate_sync(ctlr->dma_rx);
-	bs->rx_dma_active = false;
+	if (ctlr->dma_tx) {
+		dmaengine_terminate_sync(ctlr->dma_tx);
+		bs->tx_dma_active = false;
+	}
+	if (ctlr->dma_rx) {
+		dmaengine_terminate_sync(ctlr->dma_rx);
+		bs->rx_dma_active = false;
+	}
 	bcm2835_spi_undo_prologue(bs);
 
 	/* and reset */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-bcm63xx-hsspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-bcm63xx-hsspi.c
@@ -163,6 +163,7 @@
 	int step_size = HSSPI_BUFFER_LEN;
 	const u8 *tx = t->tx_buf;
 	u8 *rx = t->rx_buf;
+	u32 val = 0;
 
 	bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz);
 	bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
@@ -178,11 +179,16 @@
 		step_size -= HSSPI_OPCODE_LEN;
 
 	if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
-	    (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL))
+	    (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL)) {
 		opcode |= HSSPI_OP_MULTIBIT;
 
-	__raw_writel(1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT |
-		     1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT | 0xff,
+		if (t->rx_nbits == SPI_NBITS_DUAL)
+			val |= 1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT;
+		if (t->tx_nbits == SPI_NBITS_DUAL)
+			val |= 1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT;
+	}
+
+	__raw_writel(val | 0xff,
 		     bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
 
 	while (pending > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-bcm63xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-bcm63xx.c
@@ -126,7 +126,7 @@
 	SPI_MSG_DATA_SIZE,
 };
 
-#define BCM63XX_SPI_MAX_PREPEND		15
+#define BCM63XX_SPI_MAX_PREPEND		7
 
 #define BCM63XX_SPI_MAX_CS		8
 #define BCM63XX_SPI_BUS_NUM		0
@@ -476,12 +476,14 @@
 	{
 	},
 };
+MODULE_DEVICE_TABLE(platform, bcm63xx_spi_dev_match);
 
 static const struct of_device_id bcm63xx_spi_of_match[] = {
 	{ .compatible = "brcm,bcm6348-spi", .data = &bcm6348_spi_reg_offsets },
 	{ .compatible = "brcm,bcm6358-spi", .data = &bcm6358_spi_reg_offsets },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, bcm63xx_spi_of_match);
 
 static int bcm63xx_spi_probe(struct platform_device *pdev)
 {
@@ -593,13 +595,15 @@
 
 	bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
 
-	pm_runtime_enable(&pdev->dev);
+	ret = devm_pm_runtime_enable(&pdev->dev);
+	if (ret)
+		goto out_clk_disable;
 
 	/* register and we are done */
 	ret = devm_spi_register_master(dev, master);
 	if (ret) {
 		dev_err(dev, "spi register failed\n");
-		goto out_pm_disable;
+		goto out_clk_disable;
 	}
 
 	dev_info(dev, "at %pr (irq %d, FIFOs size %d)\n",
@@ -607,8 +611,6 @@
 
 	return 0;
 
-out_pm_disable:
-	pm_runtime_disable(&pdev->dev);
 out_clk_disable:
 	clk_disable_unprepare(clk);
 out_err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-cadence-quadspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-cadence-quadspi.c
@@ -13,13 +13,16 @@
 #include <linux/dmaengine.h>
 #include <linux/err.h>
 #include <linux/errno.h>
+#include <linux/firmware/xlnx-zynqmp.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/jiffies.h>
 #include <linux/kernel.h>
+#include <linux/log2.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
@@ -28,6 +31,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/spi-mem.h>
 #include <linux/timer.h>
+#include <linux/workqueue.h>
 
 #define CQSPI_NAME			"cadence-qspi"
 #define CQSPI_MAX_CHIPSELECT		16
@@ -35,6 +39,8 @@
 /* Quirks */
 #define CQSPI_NEEDS_WR_DELAY		BIT(0)
 #define CQSPI_DISABLE_DAC_MODE		BIT(1)
+#define CQSPI_SUPPORT_EXTERNAL_DMA	BIT(2)
+#define CQSPI_NO_SUPPORT_WR_COMPLETION	BIT(3)
 
 /* Capabilities */
 #define CQSPI_SUPPORTS_OCTAL		BIT(0)
@@ -82,22 +88,31 @@
 	u32			wr_delay;
 	bool			use_direct_mode;
 	struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT];
+	bool			wr_completion;
+	bool			use_dma_read;
+	u32			pd_dev_id;
+	bool			extra_dummy;
+	bool			clk_tuned;
+	u8			dll_mode;
+	struct completion	tuning_complete;
+	struct spi_mem_op	tuning_op;
+	int			gpio;
 };
 
 struct cqspi_driver_platdata {
 	u32 hwcaps_mask;
 	u8 quirks;
+	int (*indirect_read_dma)(struct cqspi_flash_pdata *f_pdata,
+				 u_char *rxbuf, loff_t from_addr, size_t n_rx);
+	u32 (*get_dma_status)(struct cqspi_st *cqspi);
+	int (*device_reset)(struct cqspi_st *cqspi, u8 reset_type);
 };
 
 /* Operation timeout value */
 #define CQSPI_TIMEOUT_MS			500
 #define CQSPI_READ_TIMEOUT_MS			10
-
-/* Instruction type */
-#define CQSPI_INST_TYPE_SINGLE			0
-#define CQSPI_INST_TYPE_DUAL			1
-#define CQSPI_INST_TYPE_QUAD			2
-#define CQSPI_INST_TYPE_OCTAL			3
+#define CQSPI_TUNING_TIMEOUT_MS			5000
+#define CQSPI_TUNING_PERIODICITY_MS		300000
 
 #define CQSPI_DUMMY_CLKS_PER_BYTE		8
 #define CQSPI_DUMMY_BYTES_MAX			4
@@ -108,6 +123,7 @@
 /* Register map */
 #define CQSPI_REG_CONFIG			0x00
 #define CQSPI_REG_CONFIG_ENABLE_MASK		BIT(0)
+#define CQSPI_REG_CONFIG_PHY_ENABLE_MASK	BIT(3)
 #define CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL	BIT(7)
 #define CQSPI_REG_CONFIG_DECODE_MASK		BIT(9)
 #define CQSPI_REG_CONFIG_CHIPSELECT_LSB		10
@@ -150,6 +166,7 @@
 #define CQSPI_REG_READCAPTURE_BYPASS_LSB	0
 #define CQSPI_REG_READCAPTURE_DELAY_LSB		1
 #define CQSPI_REG_READCAPTURE_DELAY_MASK	0xF
+#define CQSPI_REG_READCAPTURE_DQS_ENABLE	BIT(8)
 
 #define CQSPI_REG_SIZE				0x14
 #define CQSPI_REG_SIZE_ADDRESS_LSB		0
@@ -179,9 +196,12 @@
 
 #define CQSPI_REG_WR_COMPLETION_CTRL		0x38
 #define CQSPI_REG_WR_DISABLE_AUTO_POLL		BIT(14)
+#define CQSPI_REG_WRCOMPLETION_POLLCNT_MASK	0xFF0000
+#define CQSPI_REG_WRCOMPLETION_POLLCNY_LSB	16
 
 #define CQSPI_REG_IRQSTATUS			0x40
 #define CQSPI_REG_IRQMASK			0x44
+#define CQSPI_REG_VERSAL_ECO			0x48
 
 #define CQSPI_REG_INDIRECTRD			0x60
 #define CQSPI_REG_INDIRECTRD_START_MASK		BIT(0)
@@ -217,6 +237,8 @@
 #define CQSPI_REG_INDIRECTWRSTARTADDR		0x78
 #define CQSPI_REG_INDIRECTWRBYTES		0x7C
 
+#define CQSPI_REG_INDTRIG_ADDRRANGE		0x80
+
 #define CQSPI_REG_CMDADDRESS			0x94
 #define CQSPI_REG_CMDREADDATALOWER		0xA0
 #define CQSPI_REG_CMDREADDATAUPPER		0xA4
@@ -226,11 +248,42 @@
 #define CQSPI_REG_POLLING_STATUS		0xB0
 #define CQSPI_REG_POLLING_STATUS_DUMMY_LSB	16
 
+#define CQSPI_REG_PHY_CONFIG			0xB4
+#define CQSPI_REG_PHY_CONFIG_RESYNC_FLD_MASK	0x80000000
+#define CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK	0x40000000
+#define CQSPI_REG_PHY_CONFIG_TX_DLL_DLY_LSB	16
+
+#define CQSPI_REG_PHY_MASTER_CTRL		0xB8
+#define CQSPI_REG_DLL_LOWER			0xBC
+#define CQSPI_REG_DLL_LOWER_LPBK_LOCK_MASK	0x8000
+#define CQSPI_REG_DLL_LOWER_DLL_LOCK_MASK	0x1
+
+#define CQSPI_REG_DLL_OBSVBLE_UPPER		0xC0
+#define CQSPI_REG_DLL_UPPER_RX_FLD_MASK		0x7F
+
 #define CQSPI_REG_OP_EXT_LOWER			0xE0
 #define CQSPI_REG_OP_EXT_READ_LSB		24
 #define CQSPI_REG_OP_EXT_WRITE_LSB		16
 #define CQSPI_REG_OP_EXT_STIG_LSB		0
 
+#define CQSPI_REG_VERSAL_DMA_SRC_ADDR		0x1000
+
+#define CQSPI_REG_VERSAL_DMA_DST_ADDR		0x1800
+#define CQSPI_REG_VERSAL_DMA_DST_SIZE		0x1804
+
+#define CQSPI_REG_VERSAL_DMA_DST_CTRL		0x180C
+
+#define CQSPI_REG_VERSAL_DMA_DST_I_STS		0x1814
+#define CQSPI_REG_VERSAL_DMA_DST_I_EN		0x1818
+#define CQSPI_REG_VERSAL_DMA_DST_I_DIS		0x181C
+#define CQSPI_REG_VERSAL_DMA_DST_DONE_MASK	BIT(1)
+#define CQSPI_REG_VERSAL_DMA_DST_ALL_I_DIS_MASK	0xFE
+
+#define CQSPI_REG_VERSAL_DMA_DST_ADDR_MSB	0x1828
+
+#define CQSPI_REG_VERSAL_DMA_DST_CTRL_VAL	0xF43FFA00
+#define CQSPI_REG_VERSAL_ADDRRANGE_WIDTH_VAL	0x6
+
 /* Interrupt status bits */
 #define CQSPI_REG_IRQ_MODE_ERR			BIT(0)
 #define CQSPI_REG_IRQ_UNDERFLOW			BIT(1)
@@ -250,6 +303,24 @@
 					 CQSPI_REG_IRQ_UNDERFLOW)
 
 #define CQSPI_IRQ_STATUS_MASK		0x1FFFF
+#define CQSPI_DMA_UNALIGN		0x3
+
+#define CQSPI_REG_VERSAL_DMA_VAL		0x602
+#define CQSPI_VERSAL_MIO_NODE_ID_12	0x14108027
+#define CQSPI_RESET_TYPE_HWPIN		0
+#define CQSPI_READ_ID_LEN		6
+#define TERA_MACRO			1000000000000ULL
+#define VERSAL_OSPI_RESET		0xc10402e
+#define SILICON_VER_MASK		0xFF
+#define SILICON_VER_1			0x10
+#define CQSPI_DLL_MODE_MASTER		0
+#define CQSPI_DLL_MODE_BYPASS		1
+#define TAP_GRAN_SEL_MIN_FREQ		120000000
+#define CQSPI_TX_TAP_MASTER		0x1E
+#define CQSPI_MAX_DLL_TAPS		127
+
+#define CQSPI_CS_LOWER			0
+#define CQSPI_CS_UPPER			1
 
 static int cqspi_wait_for_bit(void __iomem *reg, const u32 mask, bool clr)
 {
@@ -275,10 +346,26 @@
 	return reg & CQSPI_REG_SDRAMLEVEL_RD_MASK;
 }
 
+static u32 cqspi_get_versal_dma_status(struct cqspi_st *cqspi)
+{
+	u32 dma_status;
+
+	dma_status = readl(cqspi->iobase +
+					   CQSPI_REG_VERSAL_DMA_DST_I_STS);
+	writel(dma_status, cqspi->iobase +
+		   CQSPI_REG_VERSAL_DMA_DST_I_STS);
+
+	return dma_status & CQSPI_REG_VERSAL_DMA_DST_DONE_MASK;
+}
+
 static irqreturn_t cqspi_irq_handler(int this_irq, void *dev)
 {
 	struct cqspi_st *cqspi = dev;
 	unsigned int irq_status;
+	struct device *device = &cqspi->pdev->dev;
+	const struct cqspi_driver_platdata *ddata;
+
+	ddata = of_device_get_match_data(device);
 
 	/* Read interrupt status */
 	irq_status = readl(cqspi->iobase + CQSPI_REG_IRQSTATUS);
@@ -286,6 +373,13 @@
 	/* Clear interrupt */
 	writel(irq_status, cqspi->iobase + CQSPI_REG_IRQSTATUS);
 
+	if (cqspi->use_dma_read && ddata && ddata->get_dma_status) {
+		if (ddata->get_dma_status(cqspi)) {
+			complete(&cqspi->transfer_complete);
+			return IRQ_HANDLED;
+		}
+	}
+
 	irq_status &= CQSPI_IRQ_MASK_RD | CQSPI_IRQ_MASK_WR;
 
 	if (irq_status)
@@ -322,10 +416,6 @@
 static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata,
 			      const struct spi_mem_op *op)
 {
-	f_pdata->inst_width = CQSPI_INST_TYPE_SINGLE;
-	f_pdata->addr_width = CQSPI_INST_TYPE_SINGLE;
-	f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
-
 	/*
 	 * For an op to be DTR, cmd phase along with every other non-empty
 	 * phase should have dtr field set to 1. If an op phase has zero
@@ -335,32 +425,23 @@
 		       (!op->addr.nbytes || op->addr.dtr) &&
 		       (!op->data.nbytes || op->data.dtr);
 
-	switch (op->data.buswidth) {
-	case 0:
-		break;
-	case 1:
-		f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
-		break;
-	case 2:
-		f_pdata->data_width = CQSPI_INST_TYPE_DUAL;
-		break;
-	case 4:
-		f_pdata->data_width = CQSPI_INST_TYPE_QUAD;
-		break;
-	case 8:
-		f_pdata->data_width = CQSPI_INST_TYPE_OCTAL;
-		break;
-	default:
-		return -EINVAL;
-	}
+	f_pdata->inst_width = 0;
+	if (op->cmd.buswidth)
+		f_pdata->inst_width = ilog2(op->cmd.buswidth);
+
+	f_pdata->addr_width = 0;
+	if (op->addr.buswidth)
+		f_pdata->addr_width = ilog2(op->addr.buswidth);
+
+	f_pdata->data_width = 0;
+	if (op->data.buswidth)
+		f_pdata->data_width = ilog2(op->data.buswidth);
 
 	/* Right now we only support 8-8-8 DTR mode. */
 	if (f_pdata->dtr) {
 		switch (op->cmd.buswidth) {
 		case 0:
-			break;
 		case 8:
-			f_pdata->inst_width = CQSPI_INST_TYPE_OCTAL;
 			break;
 		default:
 			return -EINVAL;
@@ -368,9 +449,7 @@
 
 		switch (op->addr.buswidth) {
 		case 0:
-			break;
 		case 8:
-			f_pdata->addr_width = CQSPI_INST_TYPE_OCTAL;
 			break;
 		default:
 			return -EINVAL;
@@ -378,9 +457,7 @@
 
 		switch (op->data.buswidth) {
 		case 0:
-			break;
 		case 8:
-			f_pdata->data_width = CQSPI_INST_TYPE_OCTAL;
 			break;
 		default:
 			return -EINVAL;
@@ -540,6 +617,14 @@
 
 	reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
 
+	if (op->addr.nbytes) {
+		reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
+		reg |= ((op->addr.nbytes - 1) &
+			CQSPI_REG_CMDCTRL_ADD_BYTES_MASK) <<
+			CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
+		writel(op->addr.val, reg_base + CQSPI_REG_CMDADDRESS);
+	}
+
 	rdreg = cqspi_calc_rdreg(f_pdata);
 	writel(rdreg, reg_base + CQSPI_REG_RD_INSTR);
 
@@ -547,6 +632,9 @@
 	if (dummy_clk > CQSPI_DUMMY_CLKS_MAX)
 		return -EOPNOTSUPP;
 
+	if (cqspi->extra_dummy)
+		dummy_clk++;
+
 	if (dummy_clk)
 		reg |= (dummy_clk & CQSPI_REG_CMDCTRL_DUMMY_MASK)
 		     << CQSPI_REG_CMDCTRL_DUMMY_LSB;
@@ -577,6 +665,297 @@
 	return 0;
 }
 
+static int cqspi_setdlldelay(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master);
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_flash_pdata *f_pdata;
+	int i;
+	u8 j;
+	int ret;
+	u8 *id = op->data.buf.in;
+	bool rxtapfound = false;
+	u8 min_rxtap = 0;
+	u8 max_rxtap = 0;
+	u8 avg_rxtap;
+	bool id_matched;
+	u32 txtap = 0;
+	u8 max_tap;
+	s8 max_windowsize = -1;
+	u8 windowsize;
+	u8 dummy_incr;
+	u8 dummy_flag = 0;
+	u8 count;
+	u64 tera_macro = TERA_MACRO;
+	u8 max_index = 0, min_index = 0;
+	unsigned int reg;
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg &= CQSPI_REG_CONFIG_ENABLE_MASK;
+	if (!reg)
+		return 0;
+
+	f_pdata = &cqspi->f_pdata[mem->spi->chip_select];
+	max_tap = (do_div(tera_macro, cqspi->master_ref_clk_hz) / 160);
+
+	if (cqspi->dll_mode == CQSPI_DLL_MODE_MASTER) {
+		/* Drive DLL reset bit to low */
+		writel(0, cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+
+		/* Set initial delay value */
+		writel(0x4, cqspi->iobase + CQSPI_REG_PHY_MASTER_CTRL);
+
+		/* Set DLL reset bit */
+		writel(CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK,
+		       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+
+		/* Check for loopback lock */
+		ret = cqspi_wait_for_bit(cqspi->iobase + CQSPI_REG_DLL_LOWER,
+					 CQSPI_REG_DLL_LOWER_LPBK_LOCK_MASK, 0);
+		if (ret) {
+			dev_err(&pdev->dev,
+				"Loopback lock bit error (%i)\n", ret);
+			return ret;
+		}
+
+		/* Re-synchronize slave DLLs */
+		writel(CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK,
+		       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+		writel(CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK |
+		       CQSPI_REG_PHY_CONFIG_RESYNC_FLD_MASK,
+		       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+
+		txtap = CQSPI_TX_TAP_MASTER <<
+			CQSPI_REG_PHY_CONFIG_TX_DLL_DLY_LSB;
+		max_tap = CQSPI_MAX_DLL_TAPS;
+	}
+
+	cqspi->extra_dummy = false;
+	for (dummy_incr = 0; dummy_incr <= 1; dummy_incr++) {
+		if (dummy_incr)
+			cqspi->extra_dummy = true;
+		for (i = 0; i <= max_tap; i++) {
+			writel((txtap | i |
+			       CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK),
+			       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+			writel((CQSPI_REG_PHY_CONFIG_RESYNC_FLD_MASK | txtap |
+			       i | CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK),
+			       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+			if (cqspi->dll_mode == CQSPI_DLL_MODE_MASTER) {
+				ret = cqspi_wait_for_bit(cqspi->iobase +
+							 CQSPI_REG_DLL_LOWER,
+					CQSPI_REG_DLL_LOWER_DLL_LOCK_MASK, 0);
+				if (ret)
+					return ret;
+			}
+
+			count = 0;
+			do {
+				count += 1;
+				ret = cqspi_command_read(f_pdata, op);
+				if (ret < 0) {
+					dev_err(&pdev->dev,
+						"error %d reading JEDEC ID\n", ret);
+					return ret;
+				}
+
+				id_matched = true;
+				for (j = 0; j < op->data.nbytes; j++) {
+					if (mem->device_id[j] != id[j]) {
+						id_matched = false;
+						break;
+					}
+				}
+			} while (id_matched && (count <= 10));
+
+			if (id_matched && !rxtapfound) {
+				if (cqspi->dll_mode == CQSPI_DLL_MODE_MASTER) {
+					min_rxtap = readl(cqspi->iobase +
+							  CQSPI_REG_DLL_OBSVBLE_UPPER) &
+							  CQSPI_REG_DLL_UPPER_RX_FLD_MASK;
+					max_rxtap = min_rxtap;
+					max_index = i;
+					min_index = i;
+				} else {
+					min_rxtap = i;
+					max_rxtap = i;
+				}
+				rxtapfound = true;
+			}
+
+			if (id_matched && rxtapfound) {
+				if (cqspi->dll_mode == CQSPI_DLL_MODE_MASTER) {
+					max_rxtap = readl(cqspi->iobase +
+							  CQSPI_REG_DLL_OBSVBLE_UPPER) &
+							  CQSPI_REG_DLL_UPPER_RX_FLD_MASK;
+					max_index = i;
+				} else {
+					max_rxtap = i;
+				}
+			}
+			if ((!id_matched || i == max_tap) && rxtapfound) {
+				windowsize = max_rxtap - min_rxtap + 1;
+				if (windowsize > max_windowsize) {
+					dummy_flag = dummy_incr;
+					max_windowsize = windowsize;
+					if (cqspi->dll_mode ==
+					    CQSPI_DLL_MODE_MASTER)
+						avg_rxtap = (max_index +
+							     min_index);
+					else
+						avg_rxtap = (max_rxtap +
+							     min_rxtap);
+					avg_rxtap /= 2;
+				}
+
+				if (windowsize >= 3)
+					i = max_tap;
+
+				rxtapfound = false;
+			}
+		}
+		if (!dummy_incr) {
+			rxtapfound = false;
+			min_rxtap = 0;
+			max_rxtap = 0;
+		}
+	}
+	if (!dummy_flag)
+		cqspi->extra_dummy = false;
+
+	if (max_windowsize < 3)
+		return -EINVAL;
+
+	writel((txtap | avg_rxtap | CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK),
+	       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+	writel((CQSPI_REG_PHY_CONFIG_RESYNC_FLD_MASK | txtap | avg_rxtap |
+	       CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK),
+	       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+	if (cqspi->dll_mode == CQSPI_DLL_MODE_MASTER) {
+		ret = cqspi_wait_for_bit(cqspi->iobase + CQSPI_REG_DLL_LOWER,
+					 CQSPI_REG_DLL_LOWER_DLL_LOCK_MASK, 0);
+		if (ret)
+			return ret;
+	}
+
+	cqspi->clk_tuned = true;
+
+	return 0;
+}
+
+static void cqspi_setup_ddrmode(struct cqspi_st *cqspi)
+{
+	u32 reg;
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg |= (CQSPI_REG_CONFIG_PHY_ENABLE_MASK);
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	/* Program POLL_CNT */
+	reg = readl(cqspi->iobase + CQSPI_REG_WR_COMPLETION_CTRL);
+	reg &= ~CQSPI_REG_WRCOMPLETION_POLLCNT_MASK;
+	reg |= (0x3 << CQSPI_REG_WRCOMPLETION_POLLCNY_LSB);
+	writel(reg, cqspi->iobase + CQSPI_REG_WR_COMPLETION_CTRL);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_READCAPTURE);
+	reg |= CQSPI_REG_READCAPTURE_DQS_ENABLE;
+	writel(reg, cqspi->iobase + CQSPI_REG_READCAPTURE);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+}
+
+static void cqspi_setup_sdrmode(struct cqspi_st *cqspi)
+{
+	u32 reg;
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	reg &= ~CQSPI_REG_CONFIG_DTR_PROTO;
+	reg &= ~CQSPI_REG_CONFIG_DUAL_OPCODE;
+	reg &= ~CQSPI_REG_CONFIG_PHY_ENABLE_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	/* Program POLL_CNT */
+	reg = readl(cqspi->iobase + CQSPI_REG_WR_COMPLETION_CTRL);
+	reg &= ~CQSPI_REG_WRCOMPLETION_POLLCNT_MASK;
+	reg |= (1 << CQSPI_REG_WRCOMPLETION_POLLCNY_LSB);
+	writel(reg, cqspi->iobase + CQSPI_REG_WR_COMPLETION_CTRL);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_READCAPTURE);
+	reg &= ~CQSPI_REG_READCAPTURE_DQS_ENABLE;
+	reg |= (1 & CQSPI_REG_READCAPTURE_DELAY_MASK)
+		<< CQSPI_REG_READCAPTURE_DELAY_LSB;
+	writel(reg, cqspi->iobase + CQSPI_REG_READCAPTURE);
+
+	writel(CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK,
+	       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	cqspi->clk_tuned = false;
+	cqspi->extra_dummy = false;
+}
+
+static void cqspi_periodictuning(struct work_struct *work)
+{
+	struct delayed_work *d = to_delayed_work(work);
+	struct spi_mem *mem = container_of(d, struct spi_mem, complete_work);
+	struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master);
+	int ret;
+	u8 buf[CQSPI_READ_ID_LEN];
+
+	if (!mem->request_completion.done)
+		wait_for_completion(&mem->request_completion);
+
+	reinit_completion(&cqspi->tuning_complete);
+	cqspi->tuning_op.data.buf.in = buf;
+	cqspi->tuning_op.data.nbytes = CQSPI_READ_ID_LEN;
+	ret = cqspi_setdlldelay(mem, &cqspi->tuning_op);
+	complete_all(&cqspi->tuning_complete);
+	if (ret) {
+		dev_err(&cqspi->pdev->dev,
+			"Setting dll delay error (%i)\n", ret);
+	} else {
+		schedule_delayed_work(&mem->complete_work,
+				      msecs_to_jiffies(CQSPI_TUNING_PERIODICITY_MS));
+	}
+}
+
+static int cqspi_setup_edgemode(struct spi_mem *mem,
+				const struct spi_mem_op *op)
+{
+	struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master);
+	int ret;
+
+	if (cqspi->clk_tuned)
+		return 0;
+
+	memcpy(&cqspi->tuning_op, op, sizeof(struct spi_mem_op));
+
+	cqspi_setup_ddrmode(cqspi);
+
+	ret = cqspi_setdlldelay(mem, op);
+	if (ret)
+		return ret;
+
+	complete_all(&cqspi->tuning_complete);
+	INIT_DELAYED_WORK(&mem->complete_work, cqspi_periodictuning);
+	schedule_delayed_work(&mem->complete_work,
+			      msecs_to_jiffies(CQSPI_TUNING_PERIODICITY_MS));
+
+	return 0;
+}
+
 static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata,
 			       const struct spi_mem_op *op)
 {
@@ -675,6 +1054,9 @@
 	if (dummy_clk > CQSPI_DUMMY_CLKS_MAX)
 		return -EOPNOTSUPP;
 
+	if (cqspi->extra_dummy)
+		dummy_clk++;
+
 	if (dummy_clk)
 		reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
 		       << CQSPI_REG_RD_INSTR_DUMMY_LSB;
@@ -701,15 +1083,34 @@
 	unsigned int mod_bytes = n_rx % 4;
 	unsigned int bytes_to_read = 0;
 	u8 *rxbuf_end = rxbuf + n_rx;
+	u8 *rxbuf_start = rxbuf;
 	int ret = 0;
+	u8 extra_bytes = 0;
+	u32 req_bytes;
+	u32 threshold_val;
+	bool is_unaligned_cnt = false;
+
+	if (n_rx % 2)
+		is_unaligned_cnt = true;
 
 	writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
-	writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES);
+	if (f_pdata->dtr && (from_addr % 2) != 0) {
+		mod_bytes += 1;
+		if (!is_unaligned_cnt)
+			extra_bytes = 2;
+	}
+
+	if (f_pdata->dtr && (from_addr % 2) != 0)
+		writel(from_addr - 1, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
+
+	req_bytes = remaining + is_unaligned_cnt + extra_bytes;
+	writel(req_bytes, reg_base + CQSPI_REG_INDIRECTRDBYTES);
 
 	/* Clear all interrupts. */
 	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
 
 	writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK);
+	threshold_val = readl(reg_base + CQSPI_REG_INDIRECTRDWATERMARK);
 
 	reinit_completion(&cqspi->transfer_complete);
 	writel(CQSPI_REG_INDIRECTRD_START_MASK,
@@ -720,7 +1121,10 @@
 						 msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS)))
 			ret = -ETIMEDOUT;
 
-		bytes_to_read = cqspi_get_rd_sram_level(cqspi);
+		if (req_bytes > (threshold_val + cqspi->fifo_width))
+			bytes_to_read = threshold_val + cqspi->fifo_width;
+		else
+			bytes_to_read = req_bytes;
 
 		if (ret && bytes_to_read == 0) {
 			dev_err(dev, "Indirect read timeout, no bytes\n");
@@ -729,26 +1133,48 @@
 
 		while (bytes_to_read != 0) {
 			unsigned int word_remain = round_down(remaining, 4);
+			unsigned int bytes_read = 0;
 
-			bytes_to_read *= cqspi->fifo_width;
 			bytes_to_read = bytes_to_read > remaining ?
 					remaining : bytes_to_read;
 			bytes_to_read = round_down(bytes_to_read, 4);
 			/* Read 4 byte word chunks then single bytes */
 			if (bytes_to_read) {
-				ioread32_rep(ahb_base, rxbuf,
-					     (bytes_to_read / 4));
+				u8 offset = 0;
+
+				if (f_pdata->dtr && ((from_addr % 2) != 0) &&
+				    rxbuf == rxbuf_start) {
+					unsigned int temp = ioread32(ahb_base);
+
+					temp >>= 8;
+					memcpy(rxbuf, &temp, 3);
+					bytes_to_read -= 3;
+					offset = 3;
+					bytes_read += 3;
+				}
+				if (bytes_to_read >= 4) {
+					ioread32_rep(ahb_base, rxbuf + offset,
+						     (bytes_to_read / 4));
+					bytes_read += (bytes_to_read / 4) * 4;
+				}
 			} else if (!word_remain && mod_bytes) {
 				unsigned int temp = ioread32(ahb_base);
 
-				bytes_to_read = mod_bytes;
-				memcpy(rxbuf, &temp, min((unsigned int)
-							 (rxbuf_end - rxbuf),
-							 bytes_to_read));
+				if (f_pdata->dtr && ((from_addr % 2) != 0) &&
+				    rxbuf == rxbuf_start)
+					temp >>= 8;
+
+				bytes_to_read = min(remaining, mod_bytes);
+				bytes_read = min((unsigned int)
+						    (rxbuf_end - rxbuf),
+						     bytes_to_read);
+				memcpy(rxbuf, &temp, bytes_read);
 			}
-			rxbuf += bytes_to_read;
-			remaining -= bytes_to_read;
+			rxbuf += bytes_read;
+			remaining -= bytes_read;
+			req_bytes -= bytes_read;
 			bytes_to_read = cqspi_get_rd_sram_level(cqspi);
+			bytes_to_read *= cqspi->fifo_width;
 		}
 
 		if (remaining > 0)
@@ -781,6 +1207,232 @@
 	return ret;
 }
 
+static int cqspi_versal_device_reset(struct cqspi_st *cqspi, u8 reset_type)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	int ret;
+	enum of_gpio_flags flags;
+
+	if (reset_type == CQSPI_RESET_TYPE_HWPIN) {
+		cqspi->gpio = of_get_named_gpio_flags(pdev->dev.of_node,
+						      "reset-gpios", 0, &flags);
+		if (!gpio_is_valid(cqspi->gpio))
+			return -EIO;
+		ret = devm_gpio_request_one(&pdev->dev, cqspi->gpio, flags,
+					    "flash-reset");
+		if (ret) {
+			dev_err(&pdev->dev,
+				"failed to get reset-gpios: %d\n", ret);
+			return -EIO;
+		}
+
+		/* Request for PIN */
+		zynqmp_pm_pinctrl_request(CQSPI_VERSAL_MIO_NODE_ID_12);
+
+		/* Enable hysteresis in cmos receiver */
+		zynqmp_pm_pinctrl_set_config(CQSPI_VERSAL_MIO_NODE_ID_12,
+					     PM_PINCTRL_CONFIG_SCHMITT_CMOS,
+					     PM_PINCTRL_INPUT_TYPE_SCHMITT);
+
+		/* Set the direction as output and enable the output */
+		gpio_direction_output(cqspi->gpio, 1);
+
+		/* Disable Tri-state */
+		zynqmp_pm_pinctrl_set_config(CQSPI_VERSAL_MIO_NODE_ID_12,
+					     PM_PINCTRL_CONFIG_TRI_STATE,
+					     PM_PINCTRL_TRI_STATE_DISABLE);
+		udelay(1);
+
+		/* Set value 0 to pin */
+		gpio_set_value(cqspi->gpio, 0);
+		udelay(10);
+
+		/* Set value 1 to pin */
+		gpio_set_value(cqspi->gpio, 1);
+		udelay(35);
+	} else {
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static int cqspi_versal_indirect_read_dma(struct cqspi_flash_pdata *f_pdata,
+					  u_char *rxbuf, loff_t from_addr,
+					  size_t n_rx)
+{
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
+	void __iomem *reg_base = cqspi->iobase;
+	u32 phy_reg, rd_instr, addr_width;
+	u32 reg, bytes_to_dma;
+	loff_t addr = from_addr;
+	void *buf = rxbuf;
+	dma_addr_t dma_addr;
+	u8 bytes_rem;
+	int ret = 0;
+
+	bytes_rem = n_rx % 4;
+	bytes_to_dma = (n_rx - bytes_rem);
+
+	if (!bytes_to_dma || (f_pdata->dtr && ((from_addr % 2) != 0))) {
+		bytes_to_dma = 0;
+		bytes_rem = n_rx;
+		goto nondmard;
+	}
+
+	/* Issue controller reset */
+	if (cqspi->dll_mode != CQSPI_DLL_MODE_MASTER) {
+		phy_reg = readl(cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+		rd_instr = readl(cqspi->iobase + CQSPI_REG_RD_INSTR);
+		addr_width = readl(cqspi->iobase + CQSPI_REG_SIZE);
+		zynqmp_pm_reset_assert(VERSAL_OSPI_RESET,
+				       PM_RESET_ACTION_ASSERT);
+	}
+
+	ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, PM_OSPI_MUX_SEL_DMA);
+	if (ret)
+		return ret;
+
+	if (cqspi->dll_mode != CQSPI_DLL_MODE_MASTER) {
+		zynqmp_pm_reset_assert(VERSAL_OSPI_RESET,
+				       PM_RESET_ACTION_RELEASE);
+		reg = readl(reg_base + CQSPI_REG_CONFIG);
+		reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
+		writel(reg, reg_base + CQSPI_REG_CONFIG);
+		writel(cqspi->fifo_depth / 2, cqspi->iobase +
+		       CQSPI_REG_SRAMPARTITION);
+
+		/* Load indirect trigger address. */
+		writel(cqspi->trigger_address,
+		       cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER);
+
+		/* Program read watermark -- 1/2 of the FIFO. */
+		writel(cqspi->fifo_depth * cqspi->fifo_width / 2,
+		       cqspi->iobase + CQSPI_REG_INDIRECTRDWATERMARK);
+		/* Program write watermark -- 1/8 of the FIFO. */
+		writel(cqspi->fifo_depth * cqspi->fifo_width / 8,
+		       cqspi->iobase + CQSPI_REG_INDIRECTWRWATERMARK);
+
+		/* Disable direct access controller */
+		if (!cqspi->use_direct_mode)
+			reg &= ~CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL;
+
+		reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
+		writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+		cqspi->current_cs = -1;
+		cqspi->sclk = 0;
+		if (f_pdata->dtr) {
+			cqspi_setup_ddrmode(cqspi);
+			writel(CQSPI_REG_PHY_CONFIG_RESYNC_FLD_MASK | phy_reg,
+			       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+		}
+
+		writel(rd_instr, cqspi->iobase + CQSPI_REG_RD_INSTR);
+		writel(addr_width, cqspi->iobase + CQSPI_REG_SIZE);
+	}
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg |= CQSPI_REG_CONFIG_DMA_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	dma_addr = dma_map_single(dev, rxbuf, bytes_to_dma, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev, dma_addr)) {
+		dev_err(dev, "dma mapping failed\n");
+		return -ENOMEM;
+	}
+
+	writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
+	writel(bytes_to_dma, reg_base + CQSPI_REG_INDIRECTRDBYTES);
+	writel(CQSPI_REG_VERSAL_ADDRRANGE_WIDTH_VAL,
+	       reg_base + CQSPI_REG_INDTRIG_ADDRRANGE);
+
+	/* Clear all interrupts. */
+	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+
+	/* Enable DMA done interrupt */
+	writel(CQSPI_REG_VERSAL_DMA_DST_DONE_MASK,
+	       reg_base + CQSPI_REG_VERSAL_DMA_DST_I_EN);
+
+	/* Default DMA periph configuration */
+	writel(CQSPI_REG_VERSAL_DMA_VAL, reg_base + CQSPI_REG_DMA);
+
+	/* Configure DMA Dst address */
+	writel(lower_32_bits(dma_addr),
+	       reg_base + CQSPI_REG_VERSAL_DMA_DST_ADDR);
+	writel(upper_32_bits(dma_addr),
+	       reg_base + CQSPI_REG_VERSAL_DMA_DST_ADDR_MSB);
+
+	/* Configure DMA Src address */
+	writel(cqspi->trigger_address, reg_base +
+	       CQSPI_REG_VERSAL_DMA_SRC_ADDR);
+
+	/* Set DMA destination size */
+	writel(bytes_to_dma, reg_base + CQSPI_REG_VERSAL_DMA_DST_SIZE);
+
+	/* Set DMA destination control */
+	writel(CQSPI_REG_VERSAL_DMA_DST_CTRL_VAL,
+	       reg_base + CQSPI_REG_VERSAL_DMA_DST_CTRL);
+
+	writel(CQSPI_REG_INDIRECTRD_START_MASK,
+	       reg_base + CQSPI_REG_INDIRECTRD);
+
+	reinit_completion(&cqspi->transfer_complete);
+
+	if (!wait_for_completion_timeout(&cqspi->transfer_complete,
+					 msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS))) {
+		ret = -ETIMEDOUT;
+		goto failrd;
+	}
+
+	/* Disable DMA interrupt */
+	writel(0x0, cqspi->iobase + CQSPI_REG_VERSAL_DMA_DST_I_DIS);
+
+	/* Clear indirect completion status */
+	writel(CQSPI_REG_INDIRECTRD_DONE_MASK,
+	       cqspi->iobase + CQSPI_REG_INDIRECTRD);
+	dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_FROM_DEVICE);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg &= ~CQSPI_REG_CONFIG_DMA_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id,
+					PM_OSPI_MUX_SEL_LINEAR);
+	if (ret)
+		return ret;
+
+nondmard:
+	if (bytes_rem) {
+		addr += bytes_to_dma;
+		buf += bytes_to_dma;
+		ret = cqspi_indirect_read_execute(f_pdata, buf, addr,
+						  bytes_rem);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+
+failrd:
+	/* Disable DMA interrupt */
+	writel(0x0, reg_base + CQSPI_REG_VERSAL_DMA_DST_I_DIS);
+
+	/* Cancel the indirect read */
+	writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
+	       reg_base + CQSPI_REG_INDIRECTRD);
+
+	dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_FROM_DEVICE);
+
+	reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+	reg &= ~CQSPI_REG_CONFIG_DMA_MASK;
+	writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+
+	zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, PM_OSPI_MUX_SEL_LINEAR);
+
+	return ret;
+}
+
 static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata,
 			     const struct spi_mem_op *op)
 {
@@ -819,9 +1471,11 @@
 	 * polling on the controller's side. spinand and spi-nor will take
 	 * care of polling the status register.
 	 */
-	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
-	reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
-	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+	if (cqspi->wr_completion) {
+		reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+		reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
+		writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+	}
 
 	reg = readl(reg_base + CQSPI_REG_SIZE);
 	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
@@ -840,9 +1494,14 @@
 	unsigned int remaining = n_tx;
 	unsigned int write_bytes;
 	int ret;
+	u8 unaligned_bytes = 0;
+
+	if (f_pdata->dtr && ((n_tx % 2) != 0))
+		unaligned_bytes = 1;
 
 	writel(to_addr, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR);
-	writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES);
+	writel(remaining + unaligned_bytes,
+	       reg_base + CQSPI_REG_INDIRECTWRBYTES);
 
 	/* Clear all interrupts. */
 	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
@@ -876,7 +1535,7 @@
 		if (mod_bytes) {
 			unsigned int temp = 0xFFFFFFFF;
 
-			memcpy(&temp, txbuf, mod_bytes);
+			memcpy(&temp, txbuf, mod_bytes + unaligned_bytes);
 			iowrite32(temp, cqspi->ahb_base);
 			txbuf += mod_bytes;
 		}
@@ -1180,11 +1839,15 @@
 			  const struct spi_mem_op *op)
 {
 	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
+	const struct cqspi_driver_platdata *ddata;
 	loff_t from = op->addr.val;
 	size_t len = op->data.nbytes;
 	u_char *buf = op->data.buf.in;
+	u64 dma_align = (u64)(uintptr_t)buf;
 	int ret;
 
+	ddata = of_device_get_match_data(dev);
 	ret = cqspi_set_protocol(f_pdata, op);
 	if (ret)
 		return ret;
@@ -1196,6 +1859,10 @@
 	if (cqspi->use_direct_mode && ((from + len) <= cqspi->ahb_size))
 		return cqspi_direct_read_execute(f_pdata, buf, from, len);
 
+	if (cqspi->use_dma_read && ddata && ddata->indirect_read_dma &&
+	    virt_addr_valid(buf) && ((dma_align & CQSPI_DMA_UNALIGN) == 0))
+		return ddata->indirect_read_dma(f_pdata, buf, from, len);
+
 	return cqspi_indirect_read_execute(f_pdata, buf, from, len);
 }
 
@@ -1222,8 +1889,34 @@
 
 static int cqspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
 {
+	struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master);
+	struct cqspi_flash_pdata *f_pdata;
 	int ret;
 
+	f_pdata = &cqspi->f_pdata[mem->spi->chip_select];
+
+	if (mem->spi->master->flags & SPI_MASTER_U_PAGE)
+		f_pdata->cs = CQSPI_CS_UPPER;
+	else
+		f_pdata->cs = CQSPI_CS_LOWER;
+
+	if (op->cmd.dtr &&
+	    (!op->addr.nbytes || op->addr.dtr) &&
+	    (!op->data.nbytes || op->data.dtr)) {
+		ret = cqspi_setup_edgemode(mem, op);
+		if (ret)
+			return ret;
+	} else {
+		if (cqspi->clk_tuned)
+			cqspi_setup_sdrmode(cqspi);
+	}
+
+	if (f_pdata->dtr && !cqspi->tuning_complete.done &&
+	    !wait_for_completion_timeout(&cqspi->tuning_complete,
+		msecs_to_jiffies(CQSPI_TUNING_TIMEOUT_MS))) {
+		return -ETIMEDOUT;
+	}
+
 	ret = cqspi_mem_process(mem, op);
 	if (ret)
 		dev_err(&mem->spi->dev, "operation failed with %d\n", ret);
@@ -1248,9 +1941,24 @@
 	all_false = !op->cmd.dtr && !op->addr.dtr && !op->dummy.dtr &&
 		    !op->data.dtr;
 
-	/* Mixed DTR modes not supported. */
-	if (!(all_true || all_false))
+	if (all_true) {
+		/* Right now we only support 8-8-8 DTR mode. */
+		if (op->cmd.nbytes && op->cmd.buswidth != 8)
+			return false;
+		if (op->addr.nbytes && op->addr.buswidth != 8)
+			return false;
+		if (op->data.nbytes && op->data.buswidth != 8)
+			return false;
+	} else if (all_false) {
+		/* Only 1-1-X ops are supported without DTR */
+		if (op->cmd.nbytes && op->cmd.buswidth > 1)
+			return false;
+		if (op->addr.nbytes && op->addr.buswidth > 1)
+			return false;
+	} else {
+		/* Mixed DTR modes are not supported. */
 		return false;
+	}
 
 	if (all_true)
 		return spi_mem_dtr_supports_op(mem, op);
@@ -1299,6 +2007,7 @@
 {
 	struct device *dev = &cqspi->pdev->dev;
 	struct device_node *np = dev->of_node;
+	u32 id[2];
 
 	cqspi->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs");
 
@@ -1323,6 +2032,10 @@
 
 	cqspi->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
 
+	if (!of_property_read_u32_array(np, "power-domains", id,
+					ARRAY_SIZE(id)))
+		cqspi->pd_dev_id = id[1];
+
 	return 0;
 }
 
@@ -1335,6 +2048,10 @@
 	/* Configure the remap address register, no remap */
 	writel(0, cqspi->iobase + CQSPI_REG_REMAP);
 
+	/* Reset the Delay lines */
+	writel(CQSPI_REG_PHY_CONFIG_RESET_FLD_MASK,
+	       cqspi->iobase + CQSPI_REG_PHY_CONFIG);
+
 	/* Disable all interrupts. */
 	writel(0, cqspi->iobase + CQSPI_REG_IRQMASK);
 
@@ -1359,6 +2076,13 @@
 		writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
 	}
 
+	/* Enable DMA interface */
+	if (cqspi->use_dma_read) {
+		reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+		reg &= ~CQSPI_REG_CONFIG_PHY_ENABLE_MASK;
+		writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+	}
+
 	cqspi_controller_enable(cqspi, 1);
 }
 
@@ -1372,6 +2096,7 @@
 	cqspi->rx_chan = dma_request_chan_by_mask(&mask);
 	if (IS_ERR(cqspi->rx_chan)) {
 		int ret = PTR_ERR(cqspi->rx_chan);
+
 		cqspi->rx_chan = NULL;
 		return dev_err_probe(&cqspi->pdev->dev, ret, "No Rx DMA available\n");
 	}
@@ -1443,6 +2168,8 @@
 	struct resource *res;
 	int ret;
 	int irq;
+	u32 idcode;
+	u32 version;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
 	if (!master) {
@@ -1495,6 +2222,7 @@
 	cqspi->ahb_size = resource_size(res_ahb);
 
 	init_completion(&cqspi->transfer_complete);
+	init_completion(&cqspi->tuning_complete);
 
 	/* Obtain IRQ line. */
 	irq = platform_get_irq(pdev, 0);
@@ -1539,6 +2267,10 @@
 
 	cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk);
 	master->max_speed_hz = cqspi->master_ref_clk_hz;
+
+	/* write completion is supported by default */
+	cqspi->wr_completion = true;
+
 	ddata  = of_device_get_match_data(dev);
 	if (ddata) {
 		if (ddata->quirks & CQSPI_NEEDS_WR_DELAY)
@@ -1548,6 +2280,26 @@
 			master->mode_bits |= SPI_RX_OCTAL | SPI_TX_OCTAL;
 		if (!(ddata->quirks & CQSPI_DISABLE_DAC_MODE))
 			cqspi->use_direct_mode = true;
+		if (ddata->quirks & CQSPI_NO_SUPPORT_WR_COMPLETION)
+			cqspi->wr_completion = false;
+		if (ddata->quirks & CQSPI_SUPPORT_EXTERNAL_DMA)
+			cqspi->use_dma_read = true;
+
+		if (of_device_is_compatible(pdev->dev.of_node,
+					    "xlnx,versal-ospi-1.0")) {
+			dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
+			cqspi->dll_mode = CQSPI_DLL_MODE_BYPASS;
+			ret = zynqmp_pm_get_chipid(&idcode, &version);
+			if (ret < 0) {
+				dev_err(dev, "Cannot get chipid is %d\n", ret);
+				goto probe_clk_failed;
+			}
+			if ((version & SILICON_VER_MASK) != SILICON_VER_1) {
+				cqspi->dll_mode = CQSPI_DLL_MODE_MASTER;
+				if (cqspi->master_ref_clk_hz >= TAP_GRAN_SEL_MIN_FREQ)
+					writel(0x1, cqspi->iobase + CQSPI_REG_VERSAL_ECO);
+			}
+		}
 	}
 
 	ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0,
@@ -1561,6 +2313,8 @@
 	cqspi_controller_init(cqspi);
 	cqspi->current_cs = -1;
 	cqspi->sclk = 0;
+	cqspi->extra_dummy = false;
+	cqspi->clk_tuned = false;
 
 	master->num_chipselect = cqspi->num_chipselect;
 
@@ -1570,6 +2324,12 @@
 		goto probe_setup_failed;
 	}
 
+	if (ddata->device_reset) {
+		ret = ddata->device_reset(cqspi, CQSPI_RESET_TYPE_HWPIN);
+		if (ret)
+			goto probe_setup_failed;
+	}
+
 	if (cqspi->use_direct_mode) {
 		ret = cqspi_request_mmap_dma(cqspi);
 		if (ret == -EPROBE_DEFER)
@@ -1616,17 +2376,62 @@
 static int cqspi_suspend(struct device *dev)
 {
 	struct cqspi_st *cqspi = dev_get_drvdata(dev);
+	struct spi_master *master = dev_get_drvdata(dev);
+	int ret;
 
+	if (cqspi->clk_tuned && !cqspi->tuning_complete.done &&
+	    !wait_for_completion_timeout(&cqspi->tuning_complete,
+		msecs_to_jiffies(CQSPI_TUNING_TIMEOUT_MS))) {
+		return -ETIMEDOUT;
+	}
+
+	ret = spi_master_suspend(master);
 	cqspi_controller_enable(cqspi, 0);
-	return 0;
+
+	clk_disable_unprepare(cqspi->clk);
+
+	return ret;
 }
 
 static int cqspi_resume(struct device *dev)
 {
 	struct cqspi_st *cqspi = dev_get_drvdata(dev);
+	struct spi_master *master = dev_get_drvdata(dev);
+	u32 ret;
 
-	cqspi_controller_enable(cqspi, 1);
-	return 0;
+	clk_prepare_enable(cqspi->clk);
+	cqspi_wait_idle(cqspi);
+	cqspi_controller_init(cqspi);
+
+	cqspi->current_cs = -1;
+	cqspi->sclk = 0;
+	cqspi->extra_dummy = false;
+	cqspi->clk_tuned = false;
+
+	ret = cqspi_setup_flash(cqspi);
+	if (ret) {
+		dev_err(dev, "failed to setup flash parameters %d\n", ret);
+		return ret;
+	}
+
+	ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id,
+					PM_OSPI_MUX_SEL_LINEAR);
+	if (ret)
+		return ret;
+
+	/* Set the direction as output and enable the output */
+	gpio_direction_output(cqspi->gpio, 1);
+	udelay(1);
+
+	/* Set value 0 to pin */
+	gpio_set_value(cqspi->gpio, 0);
+	udelay(10);
+
+	/* Set value 1 to pin */
+	gpio_set_value(cqspi->gpio, 1);
+	udelay(35);
+
+	return spi_master_resume(master);
 }
 
 static const struct dev_pm_ops cqspi__dev_pm_ops = {
@@ -1656,6 +2461,18 @@
 	.quirks = CQSPI_DISABLE_DAC_MODE,
 };
 
+static const struct cqspi_driver_platdata socfpga_qspi = {
+	.quirks = CQSPI_DISABLE_DAC_MODE | CQSPI_NO_SUPPORT_WR_COMPLETION,
+};
+
+static const struct cqspi_driver_platdata versal_ospi = {
+	.hwcaps_mask = CQSPI_SUPPORTS_OCTAL,
+	.quirks = CQSPI_DISABLE_DAC_MODE | CQSPI_SUPPORT_EXTERNAL_DMA,
+	.indirect_read_dma = cqspi_versal_indirect_read_dma,
+	.get_dma_status = cqspi_get_versal_dma_status,
+	.device_reset = cqspi_versal_device_reset,
+};
+
 static const struct of_device_id cqspi_dt_ids[] = {
 	{
 		.compatible = "cdns,qspi-nor",
@@ -1673,6 +2490,14 @@
 		.compatible = "intel,lgm-qspi",
 		.data = &intel_lgm_qspi,
 	},
+	{
+		.compatible = "intel,socfpga-qspi",
+		.data = (void *)&socfpga_qspi,
+	},
+	{
+		.compatible = "xlnx,versal-ospi-1.0",
+		.data = (void *)&versal_ospi,
+	},
 	{ /* end of table */ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-cadence.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-cadence.c
@@ -69,6 +69,7 @@
 #define CDNS_SPI_BAUD_DIV_SHIFT		3 /* Baud rate divisor shift in CR */
 #define CDNS_SPI_SS_SHIFT		10 /* Slave Select field shift in CR */
 #define CDNS_SPI_SS0			0x1 /* Slave Select zero */
+#define CDNS_SPI_NOSS			0x3C /* No Slave select */
 
 /*
  * SPI Interrupt Registers bit Masks
@@ -342,7 +343,8 @@
 {
 	struct spi_master *master = dev_id;
 	struct cdns_spi *xspi = spi_master_get_devdata(master);
-	u32 intr_status, status;
+	u32 intr_status;
+	irqreturn_t status;
 
 	status = IRQ_NONE;
 	intr_status = cdns_spi_read(xspi, CDNS_SPI_ISR);
@@ -449,15 +451,20 @@
  * @master:	Pointer to the spi_master structure which provides
  *		information about the controller.
  *
- * This function disables the SPI master controller.
+ * This function disables the SPI master controller when no slave selected.
  *
  * Return:	0 always
  */
 static int cdns_unprepare_transfer_hardware(struct spi_master *master)
 {
 	struct cdns_spi *xspi = spi_master_get_devdata(master);
+	u32 ctrl_reg;
 
-	cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE);
+	/* Disable the SPI if slave is deselected */
+	ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
+	ctrl_reg = (ctrl_reg & CDNS_SPI_CR_SSCTRL) >>  CDNS_SPI_SS_SHIFT;
+	if (ctrl_reg == CDNS_SPI_NOSS)
+		cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE);
 
 	return 0;
 }
@@ -475,7 +482,7 @@
 	int ret = 0, irq;
 	struct spi_master *master;
 	struct cdns_spi *xspi;
-	u32 num_cs;
+	u32 num_cs = 0;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*xspi));
 	if (!master)
@@ -650,14 +657,14 @@
 }
 
 /**
- * cdns_spi_runtime_resume - Runtime resume method for the SPI driver
+ * cdns_runtime_resume - Runtime resume method for the SPI driver
  * @dev:	Address of the platform_device structure
  *
  * This function enables the clocks
  *
  * Return:	0 on success and error value on error
  */
-static int __maybe_unused cnds_runtime_resume(struct device *dev)
+static int __maybe_unused cdns_runtime_resume(struct device *dev)
 {
 	struct spi_master *master = dev_get_drvdata(dev);
 	struct cdns_spi *xspi = spi_master_get_devdata(master);
@@ -679,14 +686,14 @@
 }
 
 /**
- * cdns_spi_runtime_suspend - Runtime suspend method for the SPI driver
+ * cdns_runtime_suspend - Runtime suspend method for the SPI driver
  * @dev:	Address of the platform_device structure
  *
  * This function disables the clocks
  *
  * Return:	Always 0
  */
-static int __maybe_unused cnds_runtime_suspend(struct device *dev)
+static int __maybe_unused cdns_runtime_suspend(struct device *dev)
 {
 	struct spi_master *master = dev_get_drvdata(dev);
 	struct cdns_spi *xspi = spi_master_get_devdata(master);
@@ -698,8 +705,8 @@
 }
 
 static const struct dev_pm_ops cdns_spi_dev_pm_ops = {
-	SET_RUNTIME_PM_OPS(cnds_runtime_suspend,
-			   cnds_runtime_resume, NULL)
+	SET_RUNTIME_PM_OPS(cdns_runtime_suspend,
+			   cdns_runtime_resume, NULL)
 	SET_SYSTEM_SLEEP_PM_OPS(cdns_spi_suspend, cdns_spi_resume)
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-dw-bt1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-dw-bt1.c
@@ -293,8 +293,10 @@
 	pm_runtime_enable(&pdev->dev);
 
 	ret = dw_spi_add_host(&pdev->dev, dws);
-	if (ret)
+	if (ret) {
+		pm_runtime_disable(&pdev->dev);
 		goto err_disable_clk;
+	}
 
 	platform_set_drvdata(pdev, dwsbt1);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-dw-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-dw-core.c
@@ -357,7 +357,7 @@
 	 * will be adjusted at the final stage of the IRQ-based SPI transfer
 	 * execution so not to lose the leftover of the incoming data.
 	 */
-	level = min_t(u16, dws->fifo_len / 2, dws->tx_len);
+	level = min_t(unsigned int, dws->fifo_len / 2, dws->tx_len);
 	dw_writel(dws, DW_SPI_TXFTLR, level);
 	dw_writel(dws, DW_SPI_RXFTLR, level - 1);
 
@@ -416,7 +416,10 @@
 	int ret;
 
 	dws->dma_mapped = 0;
-	dws->n_bytes = DIV_ROUND_UP(transfer->bits_per_word, BITS_PER_BYTE);
+	dws->n_bytes =
+		roundup_pow_of_two(DIV_ROUND_UP(transfer->bits_per_word,
+						BITS_PER_BYTE));
+
 	dws->tx = (void *)transfer->tx_buf;
 	dws->tx_len = transfer->len / dws->n_bytes;
 	dws->rx = transfer->rx_buf;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-dw-dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-dw-dma.c
@@ -127,12 +127,15 @@
 
 	dw_spi_dma_sg_burst_init(dws);
 
+	pci_dev_put(dma_dev);
+
 	return 0;
 
 free_rxchan:
 	dma_release_channel(dws->rxchan);
 	dws->rxchan = NULL;
 err_exit:
+	pci_dev_put(dma_dev);
 	return -EBUSY;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-fsl-cpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-fsl-cpm.c
@@ -21,6 +21,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 #include <linux/platform_device.h>
+#include <linux/byteorder/generic.h>
 
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-lib.h"
@@ -120,6 +121,21 @@
 		mspi->rx_dma = mspi->dma_dummy_rx;
 		mspi->map_rx_dma = 0;
 	}
+	if (t->bits_per_word == 16 && t->tx_buf) {
+		const u16 *src = t->tx_buf;
+		u16 *dst;
+		int i;
+
+		dst = kmalloc(t->len, GFP_KERNEL);
+		if (!dst)
+			return -ENOMEM;
+
+		for (i = 0; i < t->len >> 1; i++)
+			dst[i] = cpu_to_le16p(src + i);
+
+		mspi->tx = dst;
+		mspi->map_tx_dma = 1;
+	}
 
 	if (mspi->map_tx_dma) {
 		void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
@@ -173,6 +189,13 @@
 	if (mspi->map_rx_dma)
 		dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
 	mspi->xfer_in_progress = NULL;
+
+	if (t->bits_per_word == 16 && t->rx_buf) {
+		int i;
+
+		for (i = 0; i < t->len; i += 2)
+			le16_to_cpus(t->rx_buf + i);
+	}
 }
 EXPORT_SYMBOL_GPL(fsl_spi_cpm_bufs_complete);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-fsl-dspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-fsl-dspi.c
@@ -975,7 +975,9 @@
 static int dspi_setup(struct spi_device *spi)
 {
 	struct fsl_dspi *dspi = spi_controller_get_devdata(spi->controller);
+	u32 period_ns = DIV_ROUND_UP(NSEC_PER_SEC, spi->max_speed_hz);
 	unsigned char br = 0, pbr = 0, pcssck = 0, cssck = 0;
+	u32 quarter_period_ns = DIV_ROUND_UP(period_ns, 4);
 	u32 cs_sck_delay = 0, sck_cs_delay = 0;
 	struct fsl_dspi_platform_data *pdata;
 	unsigned char pasc = 0, asc = 0;
@@ -1003,6 +1005,19 @@
 		sck_cs_delay = pdata->sck_cs_delay;
 	}
 
+	/* Since tCSC and tASC apply to continuous transfers too, avoid SCK
+	 * glitches of half a cycle by never allowing tCSC + tASC to go below
+	 * half a SCK period.
+	 */
+	if (cs_sck_delay < quarter_period_ns)
+		cs_sck_delay = quarter_period_ns;
+	if (sck_cs_delay < quarter_period_ns)
+		sck_cs_delay = quarter_period_ns;
+
+	dev_dbg(&spi->dev,
+		"DSPI controller timing params: CS-to-SCK delay %u ns, SCK-to-CS delay %u ns\n",
+		cs_sck_delay, sck_cs_delay);
+
 	clkrate = clk_get_rate(dspi->clk);
 	hz_to_spi_baud(&pbr, &br, spi->max_speed_hz, clkrate);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-fsl-lpspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-fsl-lpspi.c
@@ -297,7 +297,7 @@
 static int fsl_lpspi_set_bitrate(struct fsl_lpspi_data *fsl_lpspi)
 {
 	struct lpspi_config config = fsl_lpspi->config;
-	unsigned int perclk_rate, scldiv;
+	unsigned int perclk_rate, scldiv, div;
 	u8 prescale;
 
 	perclk_rate = clk_get_rate(fsl_lpspi->clk_per);
@@ -308,8 +308,10 @@
 		return -EINVAL;
 	}
 
+	div = DIV_ROUND_UP(perclk_rate, config.speed_hz);
+
 	for (prescale = 0; prescale < 8; prescale++) {
-		scldiv = perclk_rate / config.speed_hz / (1 << prescale) - 2;
+		scldiv = div / (1 << prescale) - 2;
 		if (scldiv < 256) {
 			fsl_lpspi->config.prescale = prescale;
 			break;
@@ -869,7 +871,7 @@
 		goto out_controller_put;
 	}
 
-	ret = devm_request_irq(&pdev->dev, irq, fsl_lpspi_isr, 0,
+	ret = devm_request_irq(&pdev->dev, irq, fsl_lpspi_isr, IRQF_NO_AUTOEN,
 			       dev_name(&pdev->dev), fsl_lpspi);
 	if (ret) {
 		dev_err(&pdev->dev, "can't get irq%d: %d\n", irq, ret);
@@ -906,14 +908,15 @@
 	ret = fsl_lpspi_dma_init(&pdev->dev, fsl_lpspi, controller);
 	if (ret == -EPROBE_DEFER)
 		goto out_pm_get;
-
-	if (ret < 0)
-		dev_err(&pdev->dev, "dma setup error %d, use pio\n", ret);
+	if (ret < 0) {
+		dev_warn(&pdev->dev, "dma setup error %d, use pio\n", ret);
+		enable_irq(irq);
+	}
 
 	ret = devm_spi_register_controller(&pdev->dev, controller);
 	if (ret < 0) {
-		dev_err(&pdev->dev, "spi_register_controller error.\n");
-		goto out_pm_get;
+		dev_err_probe(&pdev->dev, ret, "spi_register_controller error\n");
+		goto free_dma;
 	}
 
 	pm_runtime_mark_last_busy(fsl_lpspi->dev);
@@ -921,6 +924,8 @@
 
 	return 0;
 
+free_dma:
+	fsl_lpspi_dma_exit(controller);
 out_pm_get:
 	pm_runtime_dont_use_autosuspend(fsl_lpspi->dev);
 	pm_runtime_put_sync(fsl_lpspi->dev);
@@ -937,6 +942,9 @@
 	struct fsl_lpspi_data *fsl_lpspi =
 				spi_controller_get_devdata(controller);
 
+	fsl_lpspi_dma_exit(controller);
+
+	pm_runtime_dont_use_autosuspend(fsl_lpspi->dev);
 	pm_runtime_disable(fsl_lpspi->dev);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-fsl-qspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-fsl-qspi.c
@@ -876,6 +876,10 @@
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 					"QuadSPI-memory");
+	if (!res) {
+		ret = -EINVAL;
+		goto err_put_ctrl;
+	}
 	q->memmap_phy = res->start;
 	/* Since there are 4 cs, map size required is 4 times ahb_buf_size */
 	q->ahb_addr = devm_ioremap(dev, q->memmap_phy,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-fsl-spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-fsl-spi.c
@@ -203,24 +203,6 @@
 	return bits_per_word;
 }
 
-static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
-				struct spi_device *spi,
-				int bits_per_word)
-{
-	/* QE uses Little Endian for words > 8
-	 * so transform all words > 8 into 8 bits
-	 * Unfortnatly that doesn't work for LSB so
-	 * reject these for now */
-	/* Note: 32 bits word, LSB works iff
-	 * tfcr/rfcr is set to CPMFCR_GBL */
-	if (spi->mode & SPI_LSB_FIRST &&
-	    bits_per_word > 8)
-		return -EINVAL;
-	if (bits_per_word > 8)
-		return 8; /* pretend its 8 bits */
-	return bits_per_word;
-}
-
 static int fsl_spi_setup_transfer(struct spi_device *spi,
 					struct spi_transfer *t)
 {
@@ -248,9 +230,6 @@
 		bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
 							   mpc8xxx_spi,
 							   bits_per_word);
-	else if (mpc8xxx_spi->flags & SPI_QE)
-		bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
-							  bits_per_word);
 
 	if (bits_per_word < 0)
 		return bits_per_word;
@@ -368,14 +347,30 @@
 	 * In CPU mode, optimize large byte transfers to use larger
 	 * bits_per_word values to reduce number of interrupts taken.
 	 */
-	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
-		list_for_each_entry(t, &m->transfers, transfer_list) {
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
 			if (t->len < 256 || t->bits_per_word != 8)
 				continue;
 			if ((t->len & 3) == 0)
 				t->bits_per_word = 32;
 			else if ((t->len & 1) == 0)
 				t->bits_per_word = 16;
+		} else {
+			/*
+			 * CPM/QE uses Little Endian for words > 8
+			 * so transform 16 and 32 bits words into 8 bits
+			 * Unfortnatly that doesn't work for LSB so
+			 * reject these for now
+			 * Note: 32 bits word, LSB works iff
+			 * tfcr/rfcr is set to CPMFCR_GBL
+			 */
+			if (m->spi->mode & SPI_LSB_FIRST && t->bits_per_word > 8)
+				return -EINVAL;
+			if (t->bits_per_word == 16 || t->bits_per_word == 32)
+				t->bits_per_word = 8; /* pretend its 8 bits */
+			if (t->bits_per_word == 8 && t->len >= 256 &&
+			    (mpc8xxx_spi->flags & SPI_CPM1))
+				t->bits_per_word = 16;
 		}
 	}
 
@@ -633,8 +628,14 @@
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
 		fsl_spi_grlib_probe(dev);
 
-	master->bits_per_word_mask =
-		(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
+	if (mpc8xxx_spi->flags & SPI_CPM_MODE)
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 8) | SPI_BPW_MASK(16) | SPI_BPW_MASK(32));
+	else
+		master->bits_per_word_mask =
+			(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32));
+
+	master->bits_per_word_mask &=
 		SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-geni-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-geni-qcom.c
@@ -32,7 +32,7 @@
 #define CS_DEMUX_OUTPUT_SEL	GENMASK(3, 0)
 
 #define SE_SPI_TRANS_CFG	0x25c
-#define CS_TOGGLE		BIT(0)
+#define CS_TOGGLE		BIT(1)
 
 #define SE_SPI_WORD_LEN		0x268
 #define WORD_LEN_MSK		GENMASK(9, 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-gpio.c
@@ -244,9 +244,19 @@
 	if (output)
 		return gpiod_direction_output(spi_gpio->mosi, 1);
 
-	ret = gpiod_direction_input(spi_gpio->mosi);
-	if (ret)
-		return ret;
+	/*
+	 * Only change MOSI to an input if using 3WIRE mode.
+	 * Otherwise, MOSI could be left floating if there is
+	 * no pull resistor connected to the I/O pin, or could
+	 * be left logic high if there is a pull-up. Transmitting
+	 * logic high when only clocking MISO data in can put some
+	 * SPI devices in to a bad state.
+	 */
+	if (spi->mode & SPI_3WIRE) {
+		ret = gpiod_direction_input(spi_gpio->mosi);
+		if (ret)
+			return ret;
+	}
 	/*
 	 * Send a turnaround high impedance cycle when switching
 	 * from output to input. Theoretically there should be
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-hisi-kunpeng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-hisi-kunpeng.c
@@ -127,7 +127,6 @@
 	void __iomem		*regs;
 	int			irq;
 	u32			fifo_len; /* depth of the FIFO buffer */
-	u16			bus_num;
 
 	/* Current message transfer state info */
 	const void		*tx;
@@ -152,8 +151,6 @@
 	HISI_SPI_DBGFS_REG("ENR", HISI_SPI_ENR),
 	HISI_SPI_DBGFS_REG("FIFOC", HISI_SPI_FIFOC),
 	HISI_SPI_DBGFS_REG("IMR", HISI_SPI_IMR),
-	HISI_SPI_DBGFS_REG("DIN", HISI_SPI_DIN),
-	HISI_SPI_DBGFS_REG("DOUT", HISI_SPI_DOUT),
 	HISI_SPI_DBGFS_REG("SR", HISI_SPI_SR),
 	HISI_SPI_DBGFS_REG("RISR", HISI_SPI_RISR),
 	HISI_SPI_DBGFS_REG("ISR", HISI_SPI_ISR),
@@ -165,7 +162,10 @@
 {
 	char name[32];
 
-	snprintf(name, 32, "hisi_spi%d", hs->bus_num);
+	struct spi_controller *master;
+
+	master = container_of(hs->dev, struct spi_controller, dev);
+	snprintf(name, 32, "hisi_spi%d", master->bus_num);
 	hs->debugfs = debugfs_create_dir(name, NULL);
 	if (!hs->debugfs)
 		return -ENOMEM;
@@ -467,7 +467,6 @@
 	hs = spi_controller_get_devdata(master);
 	hs->dev = dev;
 	hs->irq = irq;
-	hs->bus_num = pdev->id;
 
 	hs->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(hs->regs))
@@ -490,7 +489,7 @@
 	master->use_gpio_descriptors = true;
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
-	master->bus_num = hs->bus_num;
+	master->bus_num = pdev->id;
 	master->setup = hisi_spi_setup;
 	master->cleanup = hisi_spi_cleanup;
 	master->transfer_one = hisi_spi_transfer_one;
@@ -506,15 +505,15 @@
 		return ret;
 	}
 
-	if (hisi_spi_debugfs_init(hs))
-		dev_info(dev, "failed to create debugfs dir\n");
-
 	ret = spi_register_controller(master);
 	if (ret) {
 		dev_err(dev, "failed to register spi master, ret=%d\n", ret);
 		return ret;
 	}
 
+	if (hisi_spi_debugfs_init(hs))
+		dev_info(dev, "failed to create debugfs dir\n");
+
 	dev_info(dev, "hw version:0x%x max-freq:%u kHz\n",
 		readl(hs->regs + HISI_SPI_VERSION),
 		master->max_speed_hz / 1000);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-hisi-sfc-v3xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-hisi-sfc-v3xx.c
@@ -377,6 +377,11 @@
 static irqreturn_t hisi_sfc_v3xx_isr(int irq, void *data)
 {
 	struct hisi_sfc_v3xx_host *host = data;
+	u32 reg;
+
+	reg = readl(host->regbase + HISI_SFC_V3XX_INT_STAT);
+	if (!reg)
+		return IRQ_NONE;
 
 	hisi_sfc_v3xx_disable_int(host);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-img-spfi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-img-spfi.c
@@ -731,7 +731,7 @@
 	int ret;
 
 	ret = pm_runtime_get_sync(dev);
-	if (ret) {
+	if (ret < 0) {
 		pm_runtime_put_noidle(dev);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-imx.c
@@ -247,6 +247,18 @@
 	return true;
 }
 
+/*
+ * Note the number of natively supported chip selects for MX51 is 4. Some
+ * devices may have less actual SS pins but the register map supports 4. When
+ * using gpio chip selects the cs values passed into the macros below can go
+ * outside the range 0 - 3. We therefore need to limit the cs value to avoid
+ * corrupting bits outside the allocated locations.
+ *
+ * The simplest way to do this is to just mask the cs bits to 2 bits. This
+ * still allows all 4 native chip selects to work as well as gpio chip selects
+ * (which can use any of the 4 chip select configurations).
+ */
+
 #define MX51_ECSPI_CTRL		0x08
 #define MX51_ECSPI_CTRL_ENABLE		(1 <<  0)
 #define MX51_ECSPI_CTRL_XCH		(1 <<  2)
@@ -255,16 +267,16 @@
 #define MX51_ECSPI_CTRL_DRCTL(drctl)	((drctl) << 16)
 #define MX51_ECSPI_CTRL_POSTDIV_OFFSET	8
 #define MX51_ECSPI_CTRL_PREDIV_OFFSET	12
-#define MX51_ECSPI_CTRL_CS(cs)		((cs) << 18)
+#define MX51_ECSPI_CTRL_CS(cs)		((cs & 3) << 18)
 #define MX51_ECSPI_CTRL_BL_OFFSET	20
 #define MX51_ECSPI_CTRL_BL_MASK		(0xfff << 20)
 
 #define MX51_ECSPI_CONFIG	0x0c
-#define MX51_ECSPI_CONFIG_SCLKPHA(cs)	(1 << ((cs) +  0))
-#define MX51_ECSPI_CONFIG_SCLKPOL(cs)	(1 << ((cs) +  4))
-#define MX51_ECSPI_CONFIG_SBBCTRL(cs)	(1 << ((cs) +  8))
-#define MX51_ECSPI_CONFIG_SSBPOL(cs)	(1 << ((cs) + 12))
-#define MX51_ECSPI_CONFIG_SCLKCTL(cs)	(1 << ((cs) + 20))
+#define MX51_ECSPI_CONFIG_SCLKPHA(cs)	(1 << ((cs & 3) +  0))
+#define MX51_ECSPI_CONFIG_SCLKPOL(cs)	(1 << ((cs & 3) +  4))
+#define MX51_ECSPI_CONFIG_SBBCTRL(cs)	(1 << ((cs & 3) +  8))
+#define MX51_ECSPI_CONFIG_SSBPOL(cs)	(1 << ((cs & 3) + 12))
+#define MX51_ECSPI_CONFIG_SCLKCTL(cs)	(1 << ((cs & 3) + 20))
 
 #define MX51_ECSPI_INT		0x10
 #define MX51_ECSPI_INT_TEEN		(1 <<  0)
@@ -439,8 +451,7 @@
 	unsigned int pre, post;
 	unsigned int fin = spi_imx->spi_clk;
 
-	if (unlikely(fspi > fin))
-		return 0;
+	fspi = min(fspi, fin);
 
 	post = fls(fin) - fls(fspi);
 	if (fin > fspi << post)
@@ -1005,7 +1016,7 @@
 	.rx_available = mx31_rx_available,
 	.reset = mx31_reset,
 	.fifo_size = 8,
-	.has_dmamode = true,
+	.has_dmamode = false,
 	.dynamic_burst = false,
 	.has_slavemode = false,
 	.devtype = IMX35_CSPI,
@@ -1553,9 +1564,8 @@
 	struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
 	int ret;
 
-	ret = pm_runtime_get_sync(spi_imx->dev);
+	ret = pm_runtime_resume_and_get(spi_imx->dev);
 	if (ret < 0) {
-		pm_runtime_put_noidle(spi_imx->dev);
 		dev_err(spi_imx->dev, "failed to enable clock\n");
 		return ret;
 	}
@@ -1751,8 +1761,8 @@
 		spi_imx_sdma_exit(spi_imx);
 out_runtime_pm_put:
 	pm_runtime_dont_use_autosuspend(spi_imx->dev);
-	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_disable(spi_imx->dev);
+	pm_runtime_set_suspended(&pdev->dev);
 
 	clk_disable_unprepare(spi_imx->clk_ipg);
 out_put_per:
@@ -1772,13 +1782,10 @@
 	spi_bitbang_stop(&spi_imx->bitbang);
 
 	ret = pm_runtime_get_sync(spi_imx->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(spi_imx->dev);
-		dev_err(spi_imx->dev, "failed to enable clock\n");
-		return ret;
-	}
-
-	writel(0, spi_imx->base + MXC_CSPICTRL);
+	if (ret >= 0)
+		writel(0, spi_imx->base + MXC_CSPICTRL);
+	else
+		dev_warn(spi_imx->dev, "failed to enable clock, skip hw disable\n");
 
 	pm_runtime_dont_use_autosuspend(spi_imx->dev);
 	pm_runtime_put_sync(spi_imx->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-ljca.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-ljca.c
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Intel La Jolla Cove Adapter USB-SPI driver
+ *
+ * Copyright (c) 2021, Intel Corporation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/mfd/ljca.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+/* SPI commands */
+enum ljca_spi_cmd {
+	LJCA_SPI_INIT = 1,
+	LJCA_SPI_READ,
+	LJCA_SPI_WRITE,
+	LJCA_SPI_WRITEREAD,
+	LJCA_SPI_DEINIT,
+};
+
+#define LJCA_SPI_BUS_MAX_HZ 48000000
+enum {
+	LJCA_SPI_BUS_SPEED_24M,
+	LJCA_SPI_BUS_SPEED_12M,
+	LJCA_SPI_BUS_SPEED_8M,
+	LJCA_SPI_BUS_SPEED_6M,
+	LJCA_SPI_BUS_SPEED_4_8M, /*4.8MHz*/
+	LJCA_SPI_BUS_SPEED_MIN = LJCA_SPI_BUS_SPEED_4_8M,
+};
+
+enum {
+	LJCA_SPI_CLOCK_LOW_POLARITY,
+	LJCA_SPI_CLOCK_HIGH_POLARITY,
+};
+
+enum {
+	LJCA_SPI_CLOCK_FIRST_PHASE,
+	LJCA_SPI_CLOCK_SECOND_PHASE,
+};
+
+#define LJCA_SPI_BUF_SIZE 60
+#define LJCA_SPI_MAX_XFER_SIZE                                                 \
+	(LJCA_SPI_BUF_SIZE - sizeof(struct spi_xfer_packet))
+union spi_clock_mode {
+	struct {
+		u8 polarity : 1;
+		u8 phrase : 1;
+		u8 reserved : 6;
+	} u;
+
+	u8 mode;
+} __packed;
+
+struct spi_init_packet {
+	u8 index;
+	u8 speed;
+	union spi_clock_mode mode;
+} __packed;
+
+struct spi_xfer_indicator {
+	u8 id : 6;
+	u8 cmpl : 1;
+	u8 index : 1;
+};
+
+struct spi_xfer_packet {
+	struct spi_xfer_indicator indicator;
+	s8 len;
+	u8 data[];
+} __packed;
+
+struct ljca_spi_dev {
+	struct platform_device *pdev;
+	struct ljca_spi_info *ctr_info;
+	struct spi_master *master;
+	u8 speed;
+	u8 mode;
+
+	u8 obuf[LJCA_SPI_BUF_SIZE];
+	u8 ibuf[LJCA_SPI_BUF_SIZE];
+};
+
+static int ljca_spi_read_write(struct ljca_spi_dev *ljca_spi, const u8 *w_data,
+			       u8 *r_data, int len, int id, int complete,
+			       int cmd)
+{
+	struct spi_xfer_packet *w_packet =
+		(struct spi_xfer_packet *)ljca_spi->obuf;
+	struct spi_xfer_packet *r_packet =
+		(struct spi_xfer_packet *)ljca_spi->ibuf;
+	int ret;
+	int ibuf_len;
+
+	w_packet->indicator.index = ljca_spi->ctr_info->id;
+	w_packet->indicator.id = id;
+	w_packet->indicator.cmpl = complete;
+
+	if (cmd == LJCA_SPI_READ) {
+		w_packet->len = sizeof(u16);
+		*(u16 *)&w_packet->data[0] = len;
+	} else {
+		w_packet->len = len;
+		memcpy(w_packet->data, w_data, len);
+	}
+
+	ret = ljca_transfer(ljca_spi->pdev, cmd, w_packet,
+			    sizeof(*w_packet) + w_packet->len, r_packet,
+			    &ibuf_len);
+	if (ret)
+		return ret;
+
+	if (ibuf_len < sizeof(*r_packet) || r_packet->len <= 0) {
+		dev_err(&ljca_spi->pdev->dev, "receive patcket error len %d\n",
+			r_packet->len);
+		return -EIO;
+	}
+
+	if (r_data)
+		memcpy(r_data, r_packet->data, r_packet->len);
+
+	return 0;
+}
+
+static int ljca_spi_init(struct ljca_spi_dev *ljca_spi, int div, int mode)
+{
+	struct spi_init_packet w_packet = { 0 };
+	int ret;
+
+	if (ljca_spi->mode == mode && ljca_spi->speed == div)
+		return 0;
+
+	if (mode & SPI_CPOL)
+		w_packet.mode.u.polarity = LJCA_SPI_CLOCK_HIGH_POLARITY;
+	else
+		w_packet.mode.u.polarity = LJCA_SPI_CLOCK_LOW_POLARITY;
+
+	if (mode & SPI_CPHA)
+		w_packet.mode.u.phrase = LJCA_SPI_CLOCK_SECOND_PHASE;
+	else
+		w_packet.mode.u.phrase = LJCA_SPI_CLOCK_FIRST_PHASE;
+
+	w_packet.index = ljca_spi->ctr_info->id;
+	w_packet.speed = div;
+	ret = ljca_transfer(ljca_spi->pdev, LJCA_SPI_INIT, &w_packet,
+			    sizeof(w_packet), NULL, NULL);
+	if (ret)
+		return ret;
+
+	ljca_spi->mode = mode;
+	ljca_spi->speed = div;
+	return 0;
+}
+
+static int ljca_spi_deinit(struct ljca_spi_dev *ljca_spi)
+{
+	struct spi_init_packet w_packet = { 0 };
+
+	w_packet.index = ljca_spi->ctr_info->id;
+	return ljca_transfer(ljca_spi->pdev, LJCA_SPI_DEINIT, &w_packet,
+			     sizeof(w_packet), NULL, NULL);
+}
+
+static int ljca_spi_transfer(struct ljca_spi_dev *ljca_spi, const u8 *tx_data,
+			     u8 *rx_data, u16 len)
+{
+	int ret;
+	int remaining = len;
+	int offset = 0;
+	int cur_len;
+	int complete = 0;
+	int i;
+
+	for (i = 0; remaining > 0;
+	     offset += cur_len, remaining -= cur_len, i++) {
+		dev_dbg(&ljca_spi->pdev->dev,
+			"fragment %d offset %d remaining %d ret %d\n", i,
+			offset, remaining, ret);
+
+		if (remaining > LJCA_SPI_MAX_XFER_SIZE) {
+			cur_len = LJCA_SPI_MAX_XFER_SIZE;
+		} else {
+			cur_len = remaining;
+			complete = 1;
+		}
+
+		if (tx_data && rx_data)
+			ret = ljca_spi_read_write(ljca_spi, tx_data + offset,
+						  rx_data + offset, cur_len, i,
+						  complete, LJCA_SPI_WRITEREAD);
+		else if (tx_data)
+			ret = ljca_spi_read_write(ljca_spi, tx_data + offset,
+						  NULL, cur_len, i, complete,
+						  LJCA_SPI_WRITE);
+		else if (rx_data)
+			ret = ljca_spi_read_write(ljca_spi, NULL,
+						  rx_data + offset, cur_len, i,
+						  complete, LJCA_SPI_READ);
+		else
+			return -EINVAL;
+
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int ljca_spi_prepare_message(struct spi_master *master,
+				    struct spi_message *message)
+{
+	struct ljca_spi_dev *ljca_spi = spi_master_get_devdata(master);
+	struct spi_device *spi = message->spi;
+
+	dev_dbg(&ljca_spi->pdev->dev, "cs %d\n", spi->chip_select);
+	return 0;
+}
+
+static int ljca_spi_transfer_one(struct spi_master *master,
+				 struct spi_device *spi,
+				 struct spi_transfer *xfer)
+{
+	struct ljca_spi_dev *ljca_spi = spi_master_get_devdata(master);
+	int ret;
+	int div;
+
+	div = DIV_ROUND_UP(master->max_speed_hz, xfer->speed_hz) / 2 - 1;
+	if (div > LJCA_SPI_BUS_SPEED_MIN)
+		div = LJCA_SPI_BUS_SPEED_MIN;
+
+	ret = ljca_spi_init(ljca_spi, div, spi->mode);
+	if (ret < 0) {
+		dev_err(&ljca_spi->pdev->dev,
+			"cannot initialize transfer ret %d\n", ret);
+		return ret;
+	}
+
+	ret = ljca_spi_transfer(ljca_spi, xfer->tx_buf, xfer->rx_buf,
+				xfer->len);
+	if (ret < 0)
+		dev_err(&ljca_spi->pdev->dev, "ljca spi transfer failed!\n");
+
+	return ret;
+}
+
+static int ljca_spi_probe(struct platform_device *pdev)
+{
+	struct spi_master *master;
+	struct ljca_spi_dev *ljca_spi;
+	struct ljca_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	int ret;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(*ljca_spi));
+	if (!master)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, master);
+	ljca_spi = spi_master_get_devdata(master);
+
+	ljca_spi->ctr_info = &pdata->spi_info;
+	ljca_spi->master = master;
+	ljca_spi->master->dev.of_node = pdev->dev.of_node;
+	ljca_spi->pdev = pdev;
+
+	ACPI_COMPANION_SET(&ljca_spi->master->dev, ACPI_COMPANION(&pdev->dev));
+
+	master->bus_num = -1;
+	master->mode_bits = SPI_CPHA | SPI_CPOL;
+	master->prepare_message = ljca_spi_prepare_message;
+	master->transfer_one = ljca_spi_transfer_one;
+	master->auto_runtime_pm = false;
+	master->max_speed_hz = LJCA_SPI_BUS_MAX_HZ;
+
+	ret = devm_spi_register_master(&pdev->dev, master);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Failed to register master\n");
+		goto exit_free_master;
+	}
+
+	return ret;
+
+exit_free_master:
+	spi_master_put(master);
+	return ret;
+}
+
+static int ljca_spi_dev_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+	struct ljca_spi_dev *ljca_spi = spi_master_get_devdata(master);
+
+	ljca_spi_deinit(ljca_spi);
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int ljca_spi_dev_suspend(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+
+	return spi_master_suspend(master);
+}
+
+static int ljca_spi_dev_resume(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+
+	return spi_master_resume(master);
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops ljca_spi_pm = {
+	SET_SYSTEM_SLEEP_PM_OPS(ljca_spi_dev_suspend, ljca_spi_dev_resume)
+};
+
+static struct platform_driver spi_ljca_driver = {
+	.driver = {
+		.name	= "ljca-spi",
+		.pm	= &ljca_spi_pm,
+	},
+	.probe		= ljca_spi_probe,
+	.remove		= ljca_spi_dev_remove,
+};
+
+module_platform_driver(spi_ljca_driver);
+
+MODULE_AUTHOR("Ye Xiang <xiang.ye@intel.com>");
+MODULE_DESCRIPTION("Intel La Jolla Cove Adapter USB-SPI driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ljca-spi");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mem.c
@@ -8,6 +8,7 @@
 #include <linux/dmaengine.h>
 #include <linux/iopoll.h>
 #include <linux/pm_runtime.h>
+#include <linux/mtd/spi-nor.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi-mem.h>
 
@@ -15,6 +16,25 @@
 
 #define SPI_MEM_MAX_BUSWIDTH		8
 
+bool update_stripe(const struct spi_mem_op *op)
+{
+	if (op->cmd.opcode ==  SPINOR_OP_BE_4K ||
+	    op->cmd.opcode ==  SPINOR_OP_BE_32K ||
+	    op->cmd.opcode ==  SPINOR_OP_CHIP_ERASE ||
+	    op->cmd.opcode ==  SPINOR_OP_SE ||
+	    op->cmd.opcode ==  SPINOR_OP_BE_32K_4B ||
+	    op->cmd.opcode ==  SPINOR_OP_SE_4B ||
+	    op->cmd.opcode == SPINOR_OP_BE_4K_4B ||
+	    op->cmd.opcode ==  SPINOR_OP_WRSR ||
+	    op->cmd.opcode ==  SPINOR_OP_WREAR ||
+	    op->cmd.opcode ==  SPINOR_OP_BRWR ||
+	    (op->cmd.opcode ==  SPINOR_OP_WRSR2 && !op->addr.nbytes))
+		return false;
+
+	return true;
+}
+EXPORT_SYMBOL(update_stripe);
+
 /**
  * spi_controller_dma_map_mem_op_data() - DMA-map the buffer attached to a
  *					  memory operation
@@ -371,6 +391,7 @@
 		xfers[xferpos].tx_buf = tmpbuf + op->addr.nbytes + 1;
 		xfers[xferpos].len = op->dummy.nbytes;
 		xfers[xferpos].tx_nbits = op->dummy.buswidth;
+		xfers[xferpos].dummy = op->dummy.nbytes * 8;
 		xfers[xferpos].dummy_data = 1;
 		spi_message_add_tail(&xfers[xferpos], &msg);
 		xferpos++;
@@ -386,6 +407,7 @@
 			xfers[xferpos].tx_nbits = op->data.buswidth;
 		}
 
+		xfers[xferpos].stripe = update_stripe(op);
 		xfers[xferpos].len = op->data.nbytes;
 		spi_message_add_tail(&xfers[xferpos], &msg);
 		xferpos++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-meson-spicc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-meson-spicc.c
@@ -156,6 +156,7 @@
 	void __iomem			*base;
 	struct clk			*core;
 	struct clk			*pclk;
+	struct clk_divider		pow2_div;
 	struct clk			*clk;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
@@ -168,6 +169,8 @@
 	unsigned long			xfer_remain;
 };
 
+#define pow2_clk_to_spicc(_div) container_of(_div, struct meson_spicc_device, pow2_div)
+
 static void meson_spicc_oen_enable(struct meson_spicc_device *spicc)
 {
 	u32 conf;
@@ -421,7 +424,7 @@
 {
 	struct meson_spicc_device *spicc = spi_master_get_devdata(master);
 	struct spi_device *spi = message->spi;
-	u32 conf = 0;
+	u32 conf = readl_relaxed(spicc->base + SPICC_CONREG) & SPICC_DATARATE_MASK;
 
 	/* Store current message */
 	spicc->message = message;
@@ -458,8 +461,6 @@
 	/* Select CS */
 	conf |= FIELD_PREP(SPICC_CS_MASK, spi->chip_select);
 
-	/* Default Clock rate core/4 */
-
 	/* Default 8bit word */
 	conf |= FIELD_PREP(SPICC_BITLENGTH_MASK, 8 - 1);
 
@@ -476,12 +477,16 @@
 static int meson_spicc_unprepare_transfer(struct spi_master *master)
 {
 	struct meson_spicc_device *spicc = spi_master_get_devdata(master);
+	u32 conf = readl_relaxed(spicc->base + SPICC_CONREG) & SPICC_DATARATE_MASK;
 
 	/* Disable all IRQs */
 	writel(0, spicc->base + SPICC_INTREG);
 
 	device_reset_optional(&spicc->pdev->dev);
 
+	/* Set default configuration, keeping datarate field */
+	writel_relaxed(conf, spicc->base + SPICC_CONREG);
+
 	return 0;
 }
 
@@ -518,14 +523,60 @@
  * Clk path for G12A series:
  *    pclk -> pow2 fixed div -> pow2 div -> mux -> out
  *    pclk -> enh fixed div -> enh div -> mux -> out
+ *
+ * The pow2 divider is tied to the controller HW state, and the
+ * divider is only valid when the controller is initialized.
+ *
+ * A set of clock ops is added to make sure we don't read/set this
+ * clock rate while the controller is in an unknown state.
  */
 
-static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
+static unsigned long meson_spicc_pow2_recalc_rate(struct clk_hw *hw,
+						  unsigned long parent_rate)
+{
+	struct clk_divider *divider = to_clk_divider(hw);
+	struct meson_spicc_device *spicc = pow2_clk_to_spicc(divider);
+
+	if (!spicc->master->cur_msg)
+		return 0;
+
+	return clk_divider_ops.recalc_rate(hw, parent_rate);
+}
+
+static int meson_spicc_pow2_determine_rate(struct clk_hw *hw,
+					   struct clk_rate_request *req)
+{
+	struct clk_divider *divider = to_clk_divider(hw);
+	struct meson_spicc_device *spicc = pow2_clk_to_spicc(divider);
+
+	if (!spicc->master->cur_msg)
+		return -EINVAL;
+
+	return clk_divider_ops.determine_rate(hw, req);
+}
+
+static int meson_spicc_pow2_set_rate(struct clk_hw *hw, unsigned long rate,
+				     unsigned long parent_rate)
+{
+	struct clk_divider *divider = to_clk_divider(hw);
+	struct meson_spicc_device *spicc = pow2_clk_to_spicc(divider);
+
+	if (!spicc->master->cur_msg)
+		return -EINVAL;
+
+	return clk_divider_ops.set_rate(hw, rate, parent_rate);
+}
+
+const struct clk_ops meson_spicc_pow2_clk_ops = {
+	.recalc_rate = meson_spicc_pow2_recalc_rate,
+	.determine_rate = meson_spicc_pow2_determine_rate,
+	.set_rate = meson_spicc_pow2_set_rate,
+};
+
+static int meson_spicc_pow2_clk_init(struct meson_spicc_device *spicc)
 {
 	struct device *dev = &spicc->pdev->dev;
-	struct clk_fixed_factor *pow2_fixed_div, *enh_fixed_div;
-	struct clk_divider *pow2_div, *enh_div;
-	struct clk_mux *mux;
+	struct clk_fixed_factor *pow2_fixed_div;
 	struct clk_init_data init;
 	struct clk *clk;
 	struct clk_parent_data parent_data[2];
@@ -560,31 +611,45 @@
 	if (WARN_ON(IS_ERR(clk)))
 		return PTR_ERR(clk);
 
-	pow2_div = devm_kzalloc(dev, sizeof(*pow2_div), GFP_KERNEL);
-	if (!pow2_div)
-		return -ENOMEM;
-
 	snprintf(name, sizeof(name), "%s#pow2_div", dev_name(dev));
 	init.name = name;
-	init.ops = &clk_divider_ops;
-	init.flags = CLK_SET_RATE_PARENT;
+	init.ops = &meson_spicc_pow2_clk_ops;
+	/*
+	 * Set NOCACHE here to make sure we read the actual HW value
+	 * since we reset the HW after each transfer.
+	 */
+	init.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE;
 	parent_data[0].hw = &pow2_fixed_div->hw;
 	init.num_parents = 1;
 
-	pow2_div->shift = 16,
-	pow2_div->width = 3,
-	pow2_div->flags = CLK_DIVIDER_POWER_OF_TWO,
-	pow2_div->reg = spicc->base + SPICC_CONREG;
-	pow2_div->hw.init = &init;
+	spicc->pow2_div.shift = 16,
+	spicc->pow2_div.width = 3,
+	spicc->pow2_div.flags = CLK_DIVIDER_POWER_OF_TWO,
+	spicc->pow2_div.reg = spicc->base + SPICC_CONREG;
+	spicc->pow2_div.hw.init = &init;
 
-	clk = devm_clk_register(dev, &pow2_div->hw);
-	if (WARN_ON(IS_ERR(clk)))
-		return PTR_ERR(clk);
+	spicc->clk = devm_clk_register(dev, &spicc->pow2_div.hw);
+	if (WARN_ON(IS_ERR(spicc->clk)))
+		return PTR_ERR(spicc->clk);
 
-	if (!spicc->data->has_enhance_clk_div) {
-		spicc->clk = clk;
-		return 0;
-	}
+	return 0;
+}
+
+static int meson_spicc_enh_clk_init(struct meson_spicc_device *spicc)
+{
+	struct device *dev = &spicc->pdev->dev;
+	struct clk_fixed_factor *enh_fixed_div;
+	struct clk_divider *enh_div;
+	struct clk_mux *mux;
+	struct clk_init_data init;
+	struct clk *clk;
+	struct clk_parent_data parent_data[2];
+	char name[64];
+
+	memset(&init, 0, sizeof(init));
+	memset(&parent_data, 0, sizeof(parent_data));
+
+	init.parent_data = parent_data;
 
 	/* algorithm for enh div: rate = freq / 2 / (N + 1) */
 
@@ -637,7 +702,7 @@
 	snprintf(name, sizeof(name), "%s#sel", dev_name(dev));
 	init.name = name;
 	init.ops = &clk_mux_ops;
-	parent_data[0].hw = &pow2_div->hw;
+	parent_data[0].hw = &spicc->pow2_div.hw;
 	parent_data[1].hw = &enh_div->hw;
 	init.num_parents = 2;
 	init.flags = CLK_SET_RATE_PARENT;
@@ -693,6 +758,11 @@
 	writel_relaxed(0, spicc->base + SPICC_INTREG);
 
 	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto out_master;
+	}
+
 	ret = devm_request_irq(&pdev->dev, irq, meson_spicc_irq,
 			       0, NULL, spicc);
 	if (ret) {
@@ -749,12 +819,20 @@
 
 	meson_spicc_oen_enable(spicc);
 
-	ret = meson_spicc_clk_init(spicc);
+	ret = meson_spicc_pow2_clk_init(spicc);
 	if (ret) {
-		dev_err(&pdev->dev, "clock registration failed\n");
+		dev_err(&pdev->dev, "pow2 clock registration failed\n");
 		goto out_clk;
 	}
 
+	if (spicc->data->has_enhance_clk_div) {
+		ret = meson_spicc_enh_clk_init(spicc);
+		if (ret) {
+			dev_err(&pdev->dev, "clock registration failed\n");
+			goto out_clk;
+		}
+	}
+
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret) {
 		dev_err(&pdev->dev, "spi master registration failed\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-meson-spifc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-meson-spifc.c
@@ -349,6 +349,7 @@
 	return 0;
 out_clk:
 	clk_disable_unprepare(spifc->clk);
+	pm_runtime_disable(spifc->dev);
 out_err:
 	spi_master_put(master);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mpc52xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mpc52xx.c
@@ -521,6 +521,7 @@
 	struct mpc52xx_spi *ms = spi_master_get_devdata(master);
 	int i;
 
+	cancel_work_sync(&ms->work);
 	free_irq(ms->irq0, ms);
 	free_irq(ms->irq1, ms);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mt65xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mt65xx.c
@@ -43,8 +43,11 @@
 #define SPI_CFG1_PACKET_LOOP_OFFSET       8
 #define SPI_CFG1_PACKET_LENGTH_OFFSET     16
 #define SPI_CFG1_GET_TICK_DLY_OFFSET      29
+#define SPI_CFG1_GET_TICK_DLY_OFFSET_V1   30
 
 #define SPI_CFG1_GET_TICK_DLY_MASK        0xe0000000
+#define SPI_CFG1_GET_TICK_DLY_MASK_V1     0xc0000000
+
 #define SPI_CFG1_CS_IDLE_MASK             0xff
 #define SPI_CFG1_PACKET_LOOP_MASK         0xff00
 #define SPI_CFG1_PACKET_LENGTH_MASK       0x3ff0000
@@ -346,9 +349,15 @@
 
 	/* tick delay */
 	reg_val = readl(mdata->base + SPI_CFG1_REG);
-	reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK;
-	reg_val |= ((chip_config->tick_delay & 0x7)
-		<< SPI_CFG1_GET_TICK_DLY_OFFSET);
+	if (mdata->dev_comp->enhance_timing) {
+		reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK;
+		reg_val |= ((chip_config->tick_delay & 0x7)
+			    << SPI_CFG1_GET_TICK_DLY_OFFSET);
+	} else {
+		reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK_V1;
+		reg_val |= ((chip_config->tick_delay & 0x3)
+			    << SPI_CFG1_GET_TICK_DLY_OFFSET_V1);
+	}
 	writel(reg_val, mdata->base + SPI_CFG1_REG);
 
 	/* set hw cs timing */
@@ -624,7 +633,7 @@
 	else
 		mdata->state = MTK_SPI_IDLE;
 
-	if (!master->can_dma(master, master->cur_msg->spi, trans)) {
+	if (!master->can_dma(master, NULL, trans)) {
 		if (trans->rx_buf) {
 			cnt = mdata->xfer_len / 4;
 			ioread32_rep(mdata->base + SPI_RX_DATA_REG,
@@ -650,17 +659,19 @@
 		mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, len);
 		mtk_spi_setup_packet(master);
 
-		cnt = mdata->xfer_len / 4;
-		iowrite32_rep(mdata->base + SPI_TX_DATA_REG,
-				trans->tx_buf + mdata->num_xfered, cnt);
+		if (trans->tx_buf) {
+			cnt = mdata->xfer_len / 4;
+			iowrite32_rep(mdata->base + SPI_TX_DATA_REG,
+					trans->tx_buf + mdata->num_xfered, cnt);
 
-		remainder = mdata->xfer_len % 4;
-		if (remainder > 0) {
-			reg_val = 0;
-			memcpy(&reg_val,
-				trans->tx_buf + (cnt * 4) + mdata->num_xfered,
-				remainder);
-			writel(reg_val, mdata->base + SPI_TX_DATA_REG);
+			remainder = mdata->xfer_len % 4;
+			if (remainder > 0) {
+				reg_val = 0;
+				memcpy(&reg_val,
+					trans->tx_buf + (cnt * 4) + mdata->num_xfered,
+					remainder);
+				writel(reg_val, mdata->base + SPI_TX_DATA_REG);
+			}
 		}
 
 		mtk_spi_enable_transfer(master);
@@ -903,14 +914,20 @@
 {
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct mtk_spi *mdata = spi_master_get_devdata(master);
+	int ret;
 
-	pm_runtime_disable(&pdev->dev);
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret < 0)
+		return ret;
 
 	mtk_spi_reset(mdata);
 
 	if (mdata->dev_comp->no_need_unprepare)
 		clk_unprepare(mdata->spi_clk);
 
+	pm_runtime_put_noidle(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mt7621.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mt7621.c
@@ -340,11 +340,9 @@
 		return PTR_ERR(base);
 
 	clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(clk)) {
-		dev_err(&pdev->dev, "unable to get SYS clock, err=%d\n",
-			status);
-		return PTR_ERR(clk);
-	}
+	if (IS_ERR(clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(clk),
+				     "unable to get SYS clock\n");
 
 	status = clk_prepare_enable(clk);
 	if (status)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mtk-nor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mtk-nor.c
@@ -160,7 +160,7 @@
 {
 	int dummy = 0;
 
-	if (op->dummy.buswidth)
+	if (op->dummy.nbytes)
 		dummy = op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth;
 
 	if ((op->data.buswidth == 2) || (op->data.buswidth == 4)) {
@@ -909,7 +909,17 @@
 
 static int __maybe_unused mtk_nor_resume(struct device *dev)
 {
-	return pm_runtime_force_resume(dev);
+	struct spi_controller *ctlr = dev_get_drvdata(dev);
+	struct mtk_nor *sp = spi_controller_get_devdata(ctlr);
+	int ret;
+
+	ret = pm_runtime_force_resume(dev);
+	if (ret)
+		return ret;
+
+	mtk_nor_init(sp);
+
+	return 0;
 }
 
 static const struct dev_pm_ops mtk_nor_pm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mux.c
@@ -156,6 +156,7 @@
 	/* supported modes are the same as our parent's */
 	ctlr->mode_bits = spi->controller->mode_bits;
 	ctlr->flags = spi->controller->flags;
+	ctlr->bits_per_word_mask = spi->controller->bits_per_word_mask;
 	ctlr->transfer_one_message = spi_mux_transfer_one_message;
 	ctlr->setup = spi_mux_setup;
 	ctlr->num_chipselect = mux_control_states(priv->mux);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mxic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mxic.c
@@ -304,25 +304,21 @@
 
 		writel(data, mxic->regs + TXD(nbytes % 4));
 
-		if (rxbuf) {
-			ret = readl_poll_timeout(mxic->regs + INT_STS, sts,
-						 sts & INT_TX_EMPTY, 0,
-						 USEC_PER_SEC);
-			if (ret)
-				return ret;
+		ret = readl_poll_timeout(mxic->regs + INT_STS, sts,
+					 sts & INT_TX_EMPTY, 0, USEC_PER_SEC);
+		if (ret)
+			return ret;
 
-			ret = readl_poll_timeout(mxic->regs + INT_STS, sts,
-						 sts & INT_RX_NOT_EMPTY, 0,
-						 USEC_PER_SEC);
-			if (ret)
-				return ret;
+		ret = readl_poll_timeout(mxic->regs + INT_STS, sts,
+					 sts & INT_RX_NOT_EMPTY, 0,
+					 USEC_PER_SEC);
+		if (ret)
+			return ret;
 
-			data = readl(mxic->regs + RXD);
+		data = readl(mxic->regs + RXD);
+		if (rxbuf) {
 			data >>= (8 * (4 - nbytes));
 			memcpy(rxbuf + pos, &data, nbytes);
-			WARN_ON(readl(mxic->regs + INT_STS) & INT_RX_NOT_EMPTY);
-		} else {
-			readl(mxic->regs + RXD);
 		}
 		WARN_ON(readl(mxic->regs + INT_STS) & INT_RX_NOT_EMPTY);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-mxs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-mxs.c
@@ -39,6 +39,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/mxs-spi.h>
 #include <trace/events/spi.h>
+#include <linux/dma/mxs-dma.h>
 
 #define DRIVER_NAME		"mxs-spi"
 
@@ -252,7 +253,7 @@
 		desc = dmaengine_prep_slave_sg(ssp->dmach,
 				&dma_xfer[sg_count].sg, 1,
 				(flags & TXRX_WRITE) ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM,
-				DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+				DMA_PREP_INTERRUPT | MXS_DMA_CTRL_WAIT4END);
 
 		if (!desc) {
 			dev_err(ssp->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-npcm-fiu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-npcm-fiu.c
@@ -334,8 +334,9 @@
 		uma_cfg |= ilog2(op->cmd.buswidth);
 		uma_cfg |= ilog2(op->addr.buswidth)
 			<< NPCM_FIU_UMA_CFG_ADBPCK_SHIFT;
-		uma_cfg |= ilog2(op->dummy.buswidth)
-			<< NPCM_FIU_UMA_CFG_DBPCK_SHIFT;
+		if (op->dummy.nbytes)
+			uma_cfg |= ilog2(op->dummy.buswidth)
+				<< NPCM_FIU_UMA_CFG_DBPCK_SHIFT;
 		uma_cfg |= ilog2(op->data.buswidth)
 			<< NPCM_FIU_UMA_CFG_RDBPCK_SHIFT;
 		uma_cfg |= op->dummy.nbytes << NPCM_FIU_UMA_CFG_DBSIZ_SHIFT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-nxp-fspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-nxp-fspi.c
@@ -708,7 +708,7 @@
 		f->memmap_len = len > NXP_FSPI_MIN_IOMAP ?
 				len : NXP_FSPI_MIN_IOMAP;
 
-		f->ahb_addr = ioremap_wc(f->memmap_phy + f->memmap_start,
+		f->ahb_addr = ioremap(f->memmap_phy + f->memmap_start,
 					 f->memmap_len);
 
 		if (!f->ahb_addr) {
@@ -754,14 +754,15 @@
 	if (i < op->data.nbytes) {
 		u32 data = 0;
 		int j;
+		int remaining = op->data.nbytes - i;
 		/* Wait for TXFIFO empty */
 		ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
 					   FSPI_INTR_IPTXWE, 0,
 					   POLL_TOUT, true);
 		WARN_ON(ret);
 
-		for (j = 0; j < ALIGN(op->data.nbytes - i, 4); j += 4) {
-			memcpy(&data, buf + i + j, 4);
+		for (j = 0; j < ALIGN(remaining, 4); j += 4) {
+			memcpy(&data, buf + i + j, min_t(int, 4, remaining - j));
 			fspi_writel(f, data, base + FSPI_TFDR + j);
 		}
 		fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
@@ -1029,6 +1030,13 @@
 	fspi_writel(f, FSPI_AHBCR_PREF_EN | FSPI_AHBCR_RDADDROPT,
 		 base + FSPI_AHBCR);
 
+	/* Reset the FLSHxCR1 registers. */
+	reg = FSPI_FLSHXCR1_TCSH(0x3) | FSPI_FLSHXCR1_TCSS(0x3);
+	fspi_writel(f, reg, base + FSPI_FLSHA1CR1);
+	fspi_writel(f, reg, base + FSPI_FLSHA2CR1);
+	fspi_writel(f, reg, base + FSPI_FLSHB1CR1);
+	fspi_writel(f, reg, base + FSPI_FLSHB2CR1);
+
 	/* AHB Read - Set lut sequence ID for all CS. */
 	fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA1CR2);
 	fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA2CR2);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-omap-100k.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-omap-100k.c
@@ -412,6 +412,7 @@
 	return status;
 
 err_fck:
+	pm_runtime_disable(&pdev->dev);
 	clk_disable_unprepare(spi100k->fck);
 err_ick:
 	clk_disable_unprepare(spi100k->ick);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-ppc4xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-ppc4xx.c
@@ -26,7 +26,6 @@
 #include <linux/errno.h>
 #include <linux/wait.h>
 #include <linux/of_address.h>
-#include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
@@ -166,10 +165,8 @@
 	int scr;
 	u8 cdm = 0;
 	u32 speed;
-	u8 bits_per_word;
 
 	/* Start with the generic configuration for this device. */
-	bits_per_word = spi->bits_per_word;
 	speed = spi->max_speed_hz;
 
 	/*
@@ -177,9 +174,6 @@
 	 * the transfer to overwrite the generic configuration with zeros.
 	 */
 	if (t) {
-		if (t->bits_per_word)
-			bits_per_word = t->bits_per_word;
-
 		if (t->speed_hz)
 			speed = min(t->speed_hz, spi->max_speed_hz);
 	}
@@ -415,7 +409,11 @@
 	}
 
 	/* Request IRQ */
-	hw->irqnum = irq_of_parse_and_map(np, 0);
+	ret = platform_get_irq(op, 0);
+	if (ret < 0)
+		goto free_host;
+	hw->irqnum = ret;
+
 	ret = request_irq(hw->irqnum, spi_ppc4xx_int,
 			  0, "spi_ppc4xx_of", (void *)hw);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-pxa2xx-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-pxa2xx-pci.c
@@ -76,14 +76,23 @@
 	return true;
 }
 
+static void lpss_dma_put_device(void *dma_dev)
+{
+	pci_dev_put(dma_dev);
+}
+
 static int lpss_spi_setup(struct pci_dev *dev, struct pxa_spi_info *c)
 {
 	struct pci_dev *dma_dev;
+	int ret;
 
 	c->num_chipselect = 1;
 	c->max_clk_rate = 50000000;
 
 	dma_dev = pci_get_slot(dev->bus, PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
+	ret = devm_add_action_or_reset(&dev->dev, lpss_dma_put_device, dma_dev);
+	if (ret)
+		return ret;
 
 	if (c->tx_param) {
 		struct dw_dma_slave *slave = c->tx_param;
@@ -107,8 +116,9 @@
 
 static int mrfld_spi_setup(struct pci_dev *dev, struct pxa_spi_info *c)
 {
-	struct pci_dev *dma_dev = pci_get_slot(dev->bus, PCI_DEVFN(21, 0));
 	struct dw_dma_slave *tx, *rx;
+	struct pci_dev *dma_dev;
+	int ret;
 
 	switch (PCI_FUNC(dev->devfn)) {
 	case 0:
@@ -133,6 +143,11 @@
 		return -ENODEV;
 	}
 
+	dma_dev = pci_get_slot(dev->bus, PCI_DEVFN(21, 0));
+	ret = devm_add_action_or_reset(&dev->dev, lpss_dma_put_device, dma_dev);
+	if (ret)
+		return ret;
+
 	tx = c->tx_param;
 	tx->dma_dev = &dma_dev->dev;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-qup.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-qup.c
@@ -1030,23 +1030,8 @@
 		return -ENXIO;
 	}
 
-	ret = clk_prepare_enable(cclk);
-	if (ret) {
-		dev_err(dev, "cannot enable core clock\n");
-		return ret;
-	}
-
-	ret = clk_prepare_enable(iclk);
-	if (ret) {
-		clk_disable_unprepare(cclk);
-		dev_err(dev, "cannot enable iface clock\n");
-		return ret;
-	}
-
 	master = spi_alloc_master(dev, sizeof(struct spi_qup));
 	if (!master) {
-		clk_disable_unprepare(cclk);
-		clk_disable_unprepare(iclk);
 		dev_err(dev, "cannot allocate master\n");
 		return -ENOMEM;
 	}
@@ -1092,6 +1077,19 @@
 	spin_lock_init(&controller->lock);
 	init_completion(&controller->done);
 
+	ret = clk_prepare_enable(cclk);
+	if (ret) {
+		dev_err(dev, "cannot enable core clock\n");
+		goto error_dma;
+	}
+
+	ret = clk_prepare_enable(iclk);
+	if (ret) {
+		clk_disable_unprepare(cclk);
+		dev_err(dev, "cannot enable iface clock\n");
+		goto error_dma;
+	}
+
 	iomode = readl_relaxed(base + QUP_IO_M_MODES);
 
 	size = QUP_IO_M_OUTPUT_BLOCK_SIZE(iomode);
@@ -1121,7 +1119,7 @@
 	ret = spi_qup_set_state(controller, QUP_STATE_RESET);
 	if (ret) {
 		dev_err(dev, "cannot set RESET state\n");
-		goto error_dma;
+		goto error_clk;
 	}
 
 	writel_relaxed(0, base + QUP_OPERATIONAL);
@@ -1145,7 +1143,7 @@
 	ret = devm_request_irq(dev, irq, spi_qup_qup_irq,
 			       IRQF_TRIGGER_HIGH, pdev->name, controller);
 	if (ret)
-		goto error_dma;
+		goto error_clk;
 
 	pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC);
 	pm_runtime_use_autosuspend(dev);
@@ -1160,11 +1158,12 @@
 
 disable_pm:
 	pm_runtime_disable(&pdev->dev);
+error_clk:
+	clk_disable_unprepare(cclk);
+	clk_disable_unprepare(iclk);
 error_dma:
 	spi_qup_release_dma(master);
 error:
-	clk_disable_unprepare(cclk);
-	clk_disable_unprepare(iclk);
 	spi_master_put(master);
 	return ret;
 }
@@ -1199,8 +1198,10 @@
 		return ret;
 
 	ret = clk_prepare_enable(controller->cclk);
-	if (ret)
+	if (ret) {
+		clk_disable_unprepare(controller->iclk);
 		return ret;
+	}
 
 	/* Disable clocks auto gaiting */
 	config = readl_relaxed(controller->base + QUP_CONFIG);
@@ -1246,14 +1247,25 @@
 		return ret;
 
 	ret = clk_prepare_enable(controller->cclk);
-	if (ret)
+	if (ret) {
+		clk_disable_unprepare(controller->iclk);
 		return ret;
+	}
 
 	ret = spi_qup_set_state(controller, QUP_STATE_RESET);
 	if (ret)
-		return ret;
+		goto disable_clk;
+
+	ret = spi_master_resume(master);
+	if (ret)
+		goto disable_clk;
+
+	return 0;
 
-	return spi_master_resume(master);
+disable_clk:
+	clk_disable_unprepare(controller->cclk);
+	clk_disable_unprepare(controller->iclk);
+	return ret;
 }
 #endif /* CONFIG_PM_SLEEP */
 
@@ -1263,18 +1275,22 @@
 	struct spi_qup *controller = spi_master_get_devdata(master);
 	int ret;
 
-	ret = pm_runtime_resume_and_get(&pdev->dev);
-	if (ret < 0)
-		return ret;
+	ret = pm_runtime_get_sync(&pdev->dev);
 
-	ret = spi_qup_set_state(controller, QUP_STATE_RESET);
-	if (ret)
-		return ret;
+	if (ret >= 0) {
+		ret = spi_qup_set_state(controller, QUP_STATE_RESET);
+		if (ret)
+			dev_warn(&pdev->dev, "failed to reset controller (%pe)\n",
+				 ERR_PTR(ret));
 
-	spi_qup_release_dma(master);
+		clk_disable_unprepare(controller->cclk);
+		clk_disable_unprepare(controller->iclk);
+	} else {
+		dev_warn(&pdev->dev, "failed to resume, skip hw disable (%pe)\n",
+			 ERR_PTR(ret));
+	}
 
-	clk_disable_unprepare(controller->cclk);
-	clk_disable_unprepare(controller->iclk);
+	spi_qup_release_dma(master);
 
 	pm_runtime_put_noidle(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-rockchip-sfc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-rockchip-sfc.c
@@ -634,7 +634,7 @@
 	if (ret) {
 		dev_err(dev, "Failed to request irq\n");
 
-		return ret;
+		goto err_irq;
 	}
 
 	ret = rockchip_sfc_init(sfc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-rockchip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-rockchip.c
@@ -133,7 +133,8 @@
 #define INT_TF_OVERFLOW				(1 << 1)
 #define INT_RF_UNDERFLOW			(1 << 2)
 #define INT_RF_OVERFLOW				(1 << 3)
-#define INT_RF_FULL					(1 << 4)
+#define INT_RF_FULL				(1 << 4)
+#define INT_CS_INACTIVE				(1 << 6)
 
 /* Bit fields in ICR, 4bit */
 #define ICR_MASK					0x0f
@@ -194,6 +195,10 @@
 	bool cs_asserted[ROCKCHIP_SPI_MAX_CS_NUM];
 
 	bool slave_abort;
+	bool cs_inactive; /* spi slave tansmition stop when cs inactive */
+	bool cs_high_supported; /* native CS supports active-high polarity */
+
+	struct spi_transfer *xfer; /* Store xfer temporarily */
 };
 
 static inline void spi_enable_chip(struct rockchip_spi *rs, bool enable)
@@ -343,6 +348,15 @@
 	struct spi_controller *ctlr = dev_id;
 	struct rockchip_spi *rs = spi_controller_get_devdata(ctlr);
 
+	/* When int_cs_inactive comes, spi slave abort */
+	if (rs->cs_inactive && readl_relaxed(rs->regs + ROCKCHIP_SPI_IMR) & INT_CS_INACTIVE) {
+		ctlr->slave_abort(ctlr);
+		writel_relaxed(0, rs->regs + ROCKCHIP_SPI_IMR);
+		writel_relaxed(0xffffffff, rs->regs + ROCKCHIP_SPI_ICR);
+
+		return IRQ_HANDLED;
+	}
+
 	if (rs->tx_left)
 		rockchip_spi_pio_writer(rs);
 
@@ -350,6 +364,7 @@
 	if (!rs->rx_left) {
 		spi_enable_chip(rs, false);
 		writel_relaxed(0, rs->regs + ROCKCHIP_SPI_IMR);
+		writel_relaxed(0xffffffff, rs->regs + ROCKCHIP_SPI_ICR);
 		spi_finalize_current_transfer(ctlr);
 	}
 
@@ -357,14 +372,18 @@
 }
 
 static int rockchip_spi_prepare_irq(struct rockchip_spi *rs,
-		struct spi_transfer *xfer)
+				    struct spi_controller *ctlr,
+				    struct spi_transfer *xfer)
 {
 	rs->tx = xfer->tx_buf;
 	rs->rx = xfer->rx_buf;
 	rs->tx_left = rs->tx ? xfer->len / rs->n_bytes : 0;
 	rs->rx_left = xfer->len / rs->n_bytes;
 
-	writel_relaxed(INT_RF_FULL, rs->regs + ROCKCHIP_SPI_IMR);
+	if (rs->cs_inactive)
+		writel_relaxed(INT_RF_FULL | INT_CS_INACTIVE, rs->regs + ROCKCHIP_SPI_IMR);
+	else
+		writel_relaxed(INT_RF_FULL, rs->regs + ROCKCHIP_SPI_IMR);
 	spi_enable_chip(rs, true);
 
 	if (rs->tx_left)
@@ -383,6 +402,9 @@
 	if (state & TXDMA && !rs->slave_abort)
 		return;
 
+	if (rs->cs_inactive)
+		writel_relaxed(0, rs->regs + ROCKCHIP_SPI_IMR);
+
 	spi_enable_chip(rs, false);
 	spi_finalize_current_transfer(ctlr);
 }
@@ -423,14 +445,16 @@
 
 	atomic_set(&rs->state, 0);
 
+	rs->tx = xfer->tx_buf;
+	rs->rx = xfer->rx_buf;
+
 	rxdesc = NULL;
 	if (xfer->rx_buf) {
 		struct dma_slave_config rxconf = {
 			.direction = DMA_DEV_TO_MEM,
 			.src_addr = rs->dma_addr_rx,
 			.src_addr_width = rs->n_bytes,
-			.src_maxburst = rockchip_spi_calc_burst_size(xfer->len /
-								     rs->n_bytes),
+			.src_maxburst = rockchip_spi_calc_burst_size(xfer->len / rs->n_bytes),
 		};
 
 		dmaengine_slave_config(ctlr->dma_rx, &rxconf);
@@ -474,10 +498,13 @@
 	/* rx must be started before tx due to spi instinct */
 	if (rxdesc) {
 		atomic_or(RXDMA, &rs->state);
-		dmaengine_submit(rxdesc);
+		ctlr->dma_rx->cookie = dmaengine_submit(rxdesc);
 		dma_async_issue_pending(ctlr->dma_rx);
 	}
 
+	if (rs->cs_inactive)
+		writel_relaxed(INT_CS_INACTIVE, rs->regs + ROCKCHIP_SPI_IMR);
+
 	spi_enable_chip(rs, true);
 
 	if (txdesc) {
@@ -584,7 +611,48 @@
 static int rockchip_spi_slave_abort(struct spi_controller *ctlr)
 {
 	struct rockchip_spi *rs = spi_controller_get_devdata(ctlr);
+	u32 rx_fifo_left;
+	struct dma_tx_state state;
+	enum dma_status status;
+
+	/* Get current dma rx point */
+	if (atomic_read(&rs->state) & RXDMA) {
+		dmaengine_pause(ctlr->dma_rx);
+		status = dmaengine_tx_status(ctlr->dma_rx, ctlr->dma_rx->cookie, &state);
+		if (status == DMA_ERROR) {
+			rs->rx = rs->xfer->rx_buf;
+			rs->xfer->len = 0;
+			rx_fifo_left = readl_relaxed(rs->regs + ROCKCHIP_SPI_RXFLR);
+			for (; rx_fifo_left; rx_fifo_left--)
+				readl_relaxed(rs->regs + ROCKCHIP_SPI_RXDR);
+			goto out;
+		} else {
+			rs->rx += rs->xfer->len - rs->n_bytes * state.residue;
+		}
+	}
 
+	/* Get the valid data left in rx fifo and set rs->xfer->len real rx size */
+	if (rs->rx) {
+		rx_fifo_left = readl_relaxed(rs->regs + ROCKCHIP_SPI_RXFLR);
+		for (; rx_fifo_left; rx_fifo_left--) {
+			u32 rxw = readl_relaxed(rs->regs + ROCKCHIP_SPI_RXDR);
+
+			if (rs->n_bytes == 1)
+				*(u8 *)rs->rx = (u8)rxw;
+			else
+				*(u16 *)rs->rx = (u16)rxw;
+			rs->rx += rs->n_bytes;
+		}
+		rs->xfer->len = (unsigned int)(rs->rx - rs->xfer->rx_buf);
+	}
+
+out:
+	if (atomic_read(&rs->state) & RXDMA)
+		dmaengine_terminate_sync(ctlr->dma_rx);
+	if (atomic_read(&rs->state) & TXDMA)
+		dmaengine_terminate_sync(ctlr->dma_tx);
+	atomic_set(&rs->state, 0);
+	spi_enable_chip(rs, false);
 	rs->slave_abort = true;
 	spi_finalize_current_transfer(ctlr);
 
@@ -620,7 +688,7 @@
 	}
 
 	rs->n_bytes = xfer->bits_per_word <= 8 ? 1 : 2;
-
+	rs->xfer = xfer;
 	use_dma = ctlr->can_dma ? ctlr->can_dma(ctlr, spi, xfer) : false;
 
 	ret = rockchip_spi_config(rs, spi, xfer, use_dma, ctlr->slave);
@@ -630,7 +698,7 @@
 	if (use_dma)
 		return rockchip_spi_prepare_dma(rs, ctlr, xfer);
 
-	return rockchip_spi_prepare_irq(rs, xfer);
+	return rockchip_spi_prepare_irq(rs, ctlr, xfer);
 }
 
 static bool rockchip_spi_can_dma(struct spi_controller *ctlr,
@@ -647,6 +715,34 @@
 	return xfer->len / bytes_per_word >= rs->fifo_len;
 }
 
+static int rockchip_spi_setup(struct spi_device *spi)
+{
+	struct rockchip_spi *rs = spi_controller_get_devdata(spi->controller);
+	u32 cr0;
+
+	if (!spi->cs_gpiod && (spi->mode & SPI_CS_HIGH) && !rs->cs_high_supported) {
+		dev_warn(&spi->dev, "setup: non GPIO CS can't be active-high\n");
+		return -EINVAL;
+	}
+
+	pm_runtime_get_sync(rs->dev);
+
+	cr0 = readl_relaxed(rs->regs + ROCKCHIP_SPI_CTRLR0);
+
+	cr0 &= ~(0x3 << CR0_SCPH_OFFSET);
+	cr0 |= ((spi->mode & 0x3) << CR0_SCPH_OFFSET);
+	if (spi->mode & SPI_CS_HIGH && spi->chip_select <= 1)
+		cr0 |= BIT(spi->chip_select) << CR0_SOI_OFFSET;
+	else if (spi->chip_select <= 1)
+		cr0 &= ~(BIT(spi->chip_select) << CR0_SOI_OFFSET);
+
+	writel_relaxed(cr0, rs->regs + ROCKCHIP_SPI_CTRLR0);
+
+	pm_runtime_put(rs->dev);
+
+	return 0;
+}
+
 static int rockchip_spi_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -654,7 +750,7 @@
 	struct spi_controller *ctlr;
 	struct resource *mem;
 	struct device_node *np = pdev->dev.of_node;
-	u32 rsd_nsecs;
+	u32 rsd_nsecs, num_cs;
 	bool slave_mode;
 
 	slave_mode = of_property_read_bool(np, "spi-slave");
@@ -764,8 +860,9 @@
 		 * rk spi0 has two native cs, spi1..5 one cs only
 		 * if num-cs is missing in the dts, default to 1
 		 */
-		if (of_property_read_u16(np, "num-cs", &ctlr->num_chipselect))
-			ctlr->num_chipselect = 1;
+		if (of_property_read_u32(np, "num-cs", &num_cs))
+			num_cs = 1;
+		ctlr->num_chipselect = num_cs;
 		ctlr->use_gpio_descriptors = true;
 	}
 	ctlr->dev.of_node = pdev->dev.of_node;
@@ -773,6 +870,7 @@
 	ctlr->min_speed_hz = rs->freq / BAUDR_SCKDV_MAX;
 	ctlr->max_speed_hz = min(rs->freq / BAUDR_SCKDV_MIN, MAX_SCLK_OUT);
 
+	ctlr->setup = rockchip_spi_setup;
 	ctlr->set_cs = rockchip_spi_set_cs;
 	ctlr->transfer_one = rockchip_spi_transfer_one;
 	ctlr->max_transfer_size = rockchip_spi_max_transfer_size;
@@ -807,9 +905,15 @@
 
 	switch (readl_relaxed(rs->regs + ROCKCHIP_SPI_VERSION)) {
 	case ROCKCHIP_SPI_VER2_TYPE2:
+		rs->cs_high_supported = true;
 		ctlr->mode_bits |= SPI_CS_HIGH;
+		if (ctlr->can_dma && slave_mode)
+			rs->cs_inactive = true;
+		else
+			rs->cs_inactive = false;
 		break;
 	default:
+		rs->cs_inactive = false;
 		break;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-rpc-if.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-rpc-if.c
@@ -139,7 +139,9 @@
 		return -ENOMEM;
 
 	rpc = spi_controller_get_devdata(ctlr);
-	rpcif_sw_init(rpc, parent);
+	error = rpcif_sw_init(rpc, parent);
+	if (error)
+		return error;
 
 	platform_set_drvdata(pdev, ctlr);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-rspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-rspi.c
@@ -612,6 +612,10 @@
 					       rspi->dma_callbacked, HZ);
 	if (ret > 0 && rspi->dma_callbacked) {
 		ret = 0;
+		if (tx)
+			dmaengine_synchronize(rspi->ctlr->dma_tx);
+		if (rx)
+			dmaengine_synchronize(rspi->ctlr->dma_rx);
 	} else {
 		if (!ret) {
 			dev_err(&rspi->ctlr->dev, "DMA timeout\n");
@@ -1107,14 +1111,11 @@
 	}
 
 	memset(&cfg, 0, sizeof(cfg));
+	cfg.dst_addr = port_addr + RSPI_SPDR;
+	cfg.src_addr = port_addr + RSPI_SPDR;
+	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 	cfg.direction = dir;
-	if (dir == DMA_MEM_TO_DEV) {
-		cfg.dst_addr = port_addr;
-		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	} else {
-		cfg.src_addr = port_addr;
-		cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	}
 
 	ret = dmaengine_slave_config(chan, &cfg);
 	if (ret) {
@@ -1145,12 +1146,12 @@
 	}
 
 	ctlr->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
-					     res->start + RSPI_SPDR);
+					     res->start);
 	if (!ctlr->dma_tx)
 		return -ENODEV;
 
 	ctlr->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
-					     res->start + RSPI_SPDR);
+					     res->start);
 	if (!ctlr->dma_rx) {
 		dma_release_channel(ctlr->dma_tx);
 		ctlr->dma_tx = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-s3c64xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-s3c64xx.c
@@ -85,6 +85,7 @@
 #define S3C64XX_SPI_ST_TX_FIFORDY		(1<<0)
 
 #define S3C64XX_SPI_PACKET_CNT_EN		(1<<16)
+#define S3C64XX_SPI_PACKET_CNT_MASK		GENMASK(15, 0)
 
 #define S3C64XX_SPI_PND_TX_UNDERRUN_CLR		(1<<4)
 #define S3C64XX_SPI_PND_TX_OVERRUN_CLR		(1<<3)
@@ -215,7 +216,7 @@
 	loops = msecs_to_loops(1);
 	do {
 		val = readl(regs + S3C64XX_SPI_STATUS);
-	} while (TX_FIFO_LVL(val, sdd) && loops--);
+	} while (TX_FIFO_LVL(val, sdd) && --loops);
 
 	if (loops == 0)
 		dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n");
@@ -228,7 +229,7 @@
 			readl(regs + S3C64XX_SPI_RX_DATA);
 		else
 			break;
-	} while (loops--);
+	} while (--loops);
 
 	if (loops == 0)
 		dev_warn(&sdd->pdev->dev, "Timed out flushing RX FIFO\n");
@@ -661,6 +662,13 @@
 	return 0;
 }
 
+static size_t s3c64xx_spi_max_transfer_size(struct spi_device *spi)
+{
+	struct spi_controller *ctlr = spi->controller;
+
+	return ctlr->can_dma ? S3C64XX_SPI_PACKET_CNT_MASK : SIZE_MAX;
+}
+
 static int s3c64xx_spi_transfer_one(struct spi_master *master,
 				    struct spi_device *spi,
 				    struct spi_transfer *xfer)
@@ -1130,6 +1138,7 @@
 	master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer;
 	master->prepare_message = s3c64xx_spi_prepare_message;
 	master->transfer_one = s3c64xx_spi_transfer_one;
+	master->max_transfer_size = s3c64xx_spi_max_transfer_size;
 	master->num_chipselect = sci->num_cs;
 	master->dma_alignment = 8;
 	master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-sh-msiof.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-sh-msiof.c
@@ -30,12 +30,15 @@
 
 #include <asm/unaligned.h>
 
+#define SH_MSIOF_FLAG_FIXED_DTDL_200	BIT(0)
+
 struct sh_msiof_chipdata {
 	u32 bits_per_word_mask;
 	u16 tx_fifo_size;
 	u16 rx_fifo_size;
 	u16 ctlr_flags;
 	u16 min_div_pow;
+	u32 flags;
 };
 
 struct sh_msiof_spi_priv {
@@ -134,14 +137,14 @@
 
 /* SIFCTR */
 #define SIFCTR_TFWM_MASK	GENMASK(31, 29)	/* Transmit FIFO Watermark */
-#define SIFCTR_TFWM_64		(0 << 29)	/*  Transfer Request when 64 empty stages */
-#define SIFCTR_TFWM_32		(1 << 29)	/*  Transfer Request when 32 empty stages */
-#define SIFCTR_TFWM_24		(2 << 29)	/*  Transfer Request when 24 empty stages */
-#define SIFCTR_TFWM_16		(3 << 29)	/*  Transfer Request when 16 empty stages */
-#define SIFCTR_TFWM_12		(4 << 29)	/*  Transfer Request when 12 empty stages */
-#define SIFCTR_TFWM_8		(5 << 29)	/*  Transfer Request when 8 empty stages */
-#define SIFCTR_TFWM_4		(6 << 29)	/*  Transfer Request when 4 empty stages */
-#define SIFCTR_TFWM_1		(7 << 29)	/*  Transfer Request when 1 empty stage */
+#define SIFCTR_TFWM_64		(0UL << 29)	/*  Transfer Request when 64 empty stages */
+#define SIFCTR_TFWM_32		(1UL << 29)	/*  Transfer Request when 32 empty stages */
+#define SIFCTR_TFWM_24		(2UL << 29)	/*  Transfer Request when 24 empty stages */
+#define SIFCTR_TFWM_16		(3UL << 29)	/*  Transfer Request when 16 empty stages */
+#define SIFCTR_TFWM_12		(4UL << 29)	/*  Transfer Request when 12 empty stages */
+#define SIFCTR_TFWM_8		(5UL << 29)	/*  Transfer Request when 8 empty stages */
+#define SIFCTR_TFWM_4		(6UL << 29)	/*  Transfer Request when 4 empty stages */
+#define SIFCTR_TFWM_1		(7UL << 29)	/*  Transfer Request when 1 empty stage */
 #define SIFCTR_TFUA_MASK	GENMASK(26, 20) /* Transmit FIFO Usable Area */
 #define SIFCTR_TFUA_SHIFT	20
 #define SIFCTR_TFUA(i)		((i) << SIFCTR_TFUA_SHIFT)
@@ -1073,6 +1076,16 @@
 	.min_div_pow = 1,
 };
 
+static const struct sh_msiof_chipdata rcar_r8a7795_data = {
+	.bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
+			      SPI_BPW_MASK(24) | SPI_BPW_MASK(32),
+	.tx_fifo_size = 64,
+	.rx_fifo_size = 64,
+	.ctlr_flags = SPI_CONTROLLER_MUST_TX,
+	.min_div_pow = 1,
+	.flags = SH_MSIOF_FLAG_FIXED_DTDL_200,
+};
+
 static const struct of_device_id sh_msiof_match[] = {
 	{ .compatible = "renesas,sh-mobile-msiof", .data = &sh_data },
 	{ .compatible = "renesas,msiof-r8a7743",   .data = &rcar_gen2_data },
@@ -1083,6 +1096,7 @@
 	{ .compatible = "renesas,msiof-r8a7793",   .data = &rcar_gen2_data },
 	{ .compatible = "renesas,msiof-r8a7794",   .data = &rcar_gen2_data },
 	{ .compatible = "renesas,rcar-gen2-msiof", .data = &rcar_gen2_data },
+	{ .compatible = "renesas,msiof-r8a7795",   .data = &rcar_r8a7795_data },
 	{ .compatible = "renesas,msiof-r8a7796",   .data = &rcar_gen3_data },
 	{ .compatible = "renesas,rcar-gen3-msiof", .data = &rcar_gen3_data },
 	{ .compatible = "renesas,sh-msiof",        .data = &sh_data }, /* Deprecated */
@@ -1279,6 +1293,9 @@
 		return -ENXIO;
 	}
 
+	if (chipdata->flags & SH_MSIOF_FLAG_FIXED_DTDL_200)
+		info->dtdl = 200;
+
 	if (info->mode == MSIOF_SPI_SLAVE)
 		ctlr = spi_alloc_slave(&pdev->dev,
 				       sizeof(struct sh_msiof_spi_priv));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-stm32-qspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-stm32-qspi.c
@@ -308,7 +308,8 @@
 	if (!op->data.nbytes)
 		goto wait_nobusy;
 
-	if (readl_relaxed(qspi->io_base + QSPI_SR) & SR_TCF)
+	if ((readl_relaxed(qspi->io_base + QSPI_SR) & SR_TCF) ||
+	    qspi->fmode == CCR_FMODE_APM)
 		goto out;
 
 	reinit_completion(&qspi->data_completion);
@@ -397,7 +398,7 @@
 		ccr |= FIELD_PREP(CCR_ADSIZE_MASK, op->addr.nbytes - 1);
 	}
 
-	if (op->dummy.buswidth && op->dummy.nbytes)
+	if (op->dummy.nbytes)
 		ccr |= FIELD_PREP(CCR_DCYC_MASK,
 				  op->dummy.nbytes * 8 / op->dummy.buswidth);
 
@@ -688,7 +689,7 @@
 	struct resource *res;
 	int ret, irq;
 
-	ctrl = spi_alloc_master(dev, sizeof(*qspi));
+	ctrl = devm_spi_alloc_master(dev, sizeof(*qspi));
 	if (!ctrl)
 		return -ENOMEM;
 
@@ -697,58 +698,46 @@
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi");
 	qspi->io_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(qspi->io_base)) {
-		ret = PTR_ERR(qspi->io_base);
-		goto err_master_put;
-	}
+	if (IS_ERR(qspi->io_base))
+		return PTR_ERR(qspi->io_base);
 
 	qspi->phys_base = res->start;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_mm");
 	qspi->mm_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(qspi->mm_base)) {
-		ret = PTR_ERR(qspi->mm_base);
-		goto err_master_put;
-	}
+	if (IS_ERR(qspi->mm_base))
+		return PTR_ERR(qspi->mm_base);
 
 	qspi->mm_size = resource_size(res);
-	if (qspi->mm_size > STM32_QSPI_MAX_MMAP_SZ) {
-		ret = -EINVAL;
-		goto err_master_put;
-	}
+	if (qspi->mm_size > STM32_QSPI_MAX_MMAP_SZ)
+		return -EINVAL;
 
 	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		ret = irq;
-		goto err_master_put;
-	}
+	if (irq < 0)
+		return irq;
 
 	ret = devm_request_irq(dev, irq, stm32_qspi_irq, 0,
 			       dev_name(dev), qspi);
 	if (ret) {
 		dev_err(dev, "failed to request irq\n");
-		goto err_master_put;
+		return ret;
 	}
 
 	init_completion(&qspi->data_completion);
 	init_completion(&qspi->match_completion);
 
 	qspi->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(qspi->clk)) {
-		ret = PTR_ERR(qspi->clk);
-		goto err_master_put;
-	}
+	if (IS_ERR(qspi->clk))
+		return PTR_ERR(qspi->clk);
 
 	qspi->clk_rate = clk_get_rate(qspi->clk);
-	if (!qspi->clk_rate) {
-		ret = -EINVAL;
-		goto err_master_put;
-	}
+	if (!qspi->clk_rate)
+		return -EINVAL;
 
 	ret = clk_prepare_enable(qspi->clk);
 	if (ret) {
 		dev_err(dev, "can not enable the clock\n");
-		goto err_master_put;
+		return ret;
 	}
 
 	rstc = devm_reset_control_get_exclusive(dev, NULL);
@@ -784,7 +773,7 @@
 	pm_runtime_enable(dev);
 	pm_runtime_get_noresume(dev);
 
-	ret = devm_spi_register_master(dev, ctrl);
+	ret = spi_register_master(ctrl);
 	if (ret)
 		goto err_pm_runtime_free;
 
@@ -806,8 +795,6 @@
 	stm32_qspi_dma_free(qspi);
 err_clk_disable:
 	clk_disable_unprepare(qspi->clk);
-err_master_put:
-	spi_master_put(qspi->ctrl);
 
 	return ret;
 }
@@ -817,6 +804,7 @@
 	struct stm32_qspi *qspi = platform_get_drvdata(pdev);
 
 	pm_runtime_get_sync(qspi->dev);
+	spi_unregister_master(qspi->ctrl);
 	/* disable qspi */
 	writel_relaxed(0, qspi->io_base + QSPI_CR);
 	stm32_qspi_dma_free(qspi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-stm32.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-stm32.c
@@ -268,6 +268,7 @@
  * @fifo_size: size of the embedded fifo in bytes
  * @cur_midi: master inter-data idleness in ns
  * @cur_speed: speed configured in Hz
+ * @cur_half_period: time of a half bit in us
  * @cur_bpw: number of bits in a single SPI data frame
  * @cur_fthlv: fifo threshold level (data frames in a single data packet)
  * @cur_comm: SPI communication mode
@@ -294,6 +295,7 @@
 
 	unsigned int cur_midi;
 	unsigned int cur_speed;
+	unsigned int cur_half_period;
 	unsigned int cur_bpw;
 	unsigned int cur_fthlv;
 	unsigned int cur_comm;
@@ -434,7 +436,7 @@
 	u32 div, mbrdiv;
 
 	/* Ensure spi->clk_rate is even */
-	div = DIV_ROUND_UP(spi->clk_rate & ~0x1, speed_hz);
+	div = DIV_ROUND_CLOSEST(spi->clk_rate & ~0x1, speed_hz);
 
 	/*
 	 * SPI framework set xfer->speed_hz to master->max_speed_hz if
@@ -454,6 +456,8 @@
 
 	spi->cur_speed = spi->clk_rate / (1 << mbrdiv);
 
+	spi->cur_half_period = DIV_ROUND_CLOSEST(USEC_PER_SEC, 2 * spi->cur_speed);
+
 	return mbrdiv - 1;
 }
 
@@ -695,6 +699,10 @@
 		return;
 	}
 
+	/* Add a delay to make sure that transmission is ended. */
+	if (spi->cur_half_period)
+		udelay(spi->cur_half_period);
+
 	if (spi->cur_usedma && spi->dma_tx)
 		dmaengine_terminate_all(spi->dma_tx);
 	if (spi->cur_usedma && spi->dma_rx)
@@ -876,7 +884,7 @@
 		mask |= STM32H7_SPI_SR_TXP | STM32H7_SPI_SR_RXP;
 
 	if (!(sr & mask)) {
-		dev_warn(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
+		dev_vdbg(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
 			 sr, ier);
 		spin_unlock_irqrestore(&spi->lock, flags);
 		return IRQ_NONE;
@@ -886,6 +894,7 @@
 		static DEFINE_RATELIMIT_STATE(rs,
 					      DEFAULT_RATELIMIT_INTERVAL * 10,
 					      1);
+		ratelimit_set_flags(&rs, RATELIMIT_MSG_ON_RELEASE);
 		if (__ratelimit(&rs))
 			dev_dbg_ratelimited(spi->dev, "Communication suspended\n");
 		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-sun6i.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-sun6i.c
@@ -95,6 +95,7 @@
 	struct reset_control	*rstc;
 
 	struct completion	done;
+	struct completion	dma_rx_done;
 
 	const u8		*tx_buf;
 	u8			*rx_buf;
@@ -189,6 +190,13 @@
 	return SUN6I_MAX_XFER_SIZE - 1;
 }
 
+static void sun6i_spi_dma_rx_cb(void *param)
+{
+	struct sun6i_spi *sspi = param;
+
+	complete(&sspi->dma_rx_done);
+}
+
 static int sun6i_spi_prepare_dma(struct sun6i_spi *sspi,
 				 struct spi_transfer *tfr)
 {
@@ -200,7 +208,7 @@
 		struct dma_slave_config rxconf = {
 			.direction = DMA_DEV_TO_MEM,
 			.src_addr = sspi->dma_addr_rx,
-			.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
+			.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
 			.src_maxburst = 8,
 		};
 
@@ -213,6 +221,8 @@
 						 DMA_PREP_INTERRUPT);
 		if (!rxdesc)
 			return -EINVAL;
+		rxdesc->callback_param = sspi;
+		rxdesc->callback = sun6i_spi_dma_rx_cb;
 	}
 
 	txdesc = NULL;
@@ -268,6 +278,7 @@
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);
+	reinit_completion(&sspi->dma_rx_done);
 	sspi->tx_buf = tfr->tx_buf;
 	sspi->rx_buf = tfr->rx_buf;
 	sspi->len = tfr->len;
@@ -426,6 +437,22 @@
 	start = jiffies;
 	timeout = wait_for_completion_timeout(&sspi->done,
 					      msecs_to_jiffies(tx_time));
+
+	if (!use_dma) {
+		sun6i_spi_drain_fifo(sspi);
+	} else {
+		if (timeout && rx_len) {
+			/*
+			 * Even though RX on the peripheral side has finished
+			 * RX DMA might still be in flight
+			 */
+			timeout = wait_for_completion_timeout(&sspi->dma_rx_done,
+							      timeout);
+			if (!timeout)
+				dev_warn(&master->dev, "RX DMA timeout\n");
+		}
+	}
+
 	end = jiffies;
 	if (!timeout) {
 		dev_warn(&master->dev,
@@ -453,7 +480,6 @@
 	/* Transfer complete */
 	if (status & SUN6I_INT_CTL_TC) {
 		sun6i_spi_write(sspi, SUN6I_INT_STA_REG, SUN6I_INT_CTL_TC);
-		sun6i_spi_drain_fifo(sspi);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
@@ -611,6 +637,7 @@
 	}
 
 	init_completion(&sspi->done);
+	init_completion(&sspi->dma_rx_done);
 
 	sspi->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
 	if (IS_ERR(sspi->rstc)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-synquacer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-synquacer.c
@@ -472,10 +472,9 @@
 		read_fifo(sspi);
 	}
 
-	if (status < 0) {
-		dev_err(sspi->dev, "failed to transfer. status: 0x%x\n",
-			status);
-		return status;
+	if (status == 0) {
+		dev_err(sspi->dev, "failed to transfer. Timeout.\n");
+		return -ETIMEDOUT;
 	}
 
 	return 0;
@@ -783,6 +782,7 @@
 
 		ret = synquacer_spi_enable(master);
 		if (ret) {
+			clk_disable_unprepare(sspi->clk);
 			dev_err(dev, "failed to enable spi (%d)\n", ret);
 			return ret;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-tegra114.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-tegra114.c
@@ -1352,6 +1352,10 @@
 	tspi->phys = r->start;
 
 	spi_irq = platform_get_irq(pdev, 0);
+	if (spi_irq < 0) {
+		ret = spi_irq;
+		goto exit_free_master;
+	}
 	tspi->irq = spi_irq;
 
 	tspi->clk = devm_clk_get(&pdev->dev, "spi");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-tegra20-sflash.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-tegra20-sflash.c
@@ -455,7 +455,11 @@
 		goto exit_free_master;
 	}
 
-	tsd->irq = platform_get_irq(pdev, 0);
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0)
+		goto exit_free_master;
+	tsd->irq = ret;
+
 	ret = request_irq(tsd->irq, tegra_sflash_isr, 0,
 			dev_name(&pdev->dev), tsd);
 	if (ret < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-tegra20-slink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-tegra20-slink.c
@@ -1003,14 +1003,8 @@
 	struct resource		*r;
 	int ret, spi_irq;
 	const struct tegra_slink_chip_data *cdata = NULL;
-	const struct of_device_id *match;
 
-	match = of_match_device(tegra_slink_of_match, &pdev->dev);
-	if (!match) {
-		dev_err(&pdev->dev, "Error: No device match found\n");
-		return -ENODEV;
-	}
-	cdata = match->data;
+	cdata = of_device_get_match_data(&pdev->dev);
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*tspi));
 	if (!master) {
@@ -1093,6 +1087,8 @@
 	reset_control_deassert(tspi->rst);
 
 	spi_irq = platform_get_irq(pdev, 0);
+	if (spi_irq < 0)
+		return spi_irq;
 	tspi->irq = spi_irq;
 	ret = request_threaded_irq(tspi->irq, tegra_slink_isr,
 				   tegra_slink_isr_thread, IRQF_ONESHOT,
@@ -1136,7 +1132,7 @@
 
 static int tegra_slink_remove(struct platform_device *pdev)
 {
-	struct spi_master *master = platform_get_drvdata(pdev);
+	struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
 	struct tegra_slink_data	*tspi = spi_master_get_devdata(master);
 
 	spi_unregister_master(master);
@@ -1151,6 +1147,7 @@
 	if (tspi->rx_dma_chan)
 		tegra_slink_deinit_dma_param(tspi, true);
 
+	spi_master_put(master);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-tegra210-quad.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-tegra210-quad.c
@@ -298,7 +298,7 @@
 		for (count = 0; count < max_n_32bit; count++) {
 			u32 x = 0;
 
-			for (i = 0; len && (i < bytes_per_word); i++, len--)
+			for (i = 0; len && (i < min(4, bytes_per_word)); i++, len--)
 				x |= (u32)(*tx_buf++) << (i * 8);
 			tegra_qspi_writel(tqspi, x, QSPI_TX_FIFO);
 		}
@@ -1249,6 +1249,8 @@
 
 	tqspi->phys = r->start;
 	qspi_irq = platform_get_irq(pdev, 0);
+	if (qspi_irq < 0)
+		return qspi_irq;
 	tqspi->irq = qspi_irq;
 
 	tqspi->clk = devm_clk_get(&pdev->dev, "qspi");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-ti-qspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-ti-qspi.c
@@ -448,6 +448,7 @@
 	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
 	struct dma_async_tx_descriptor *tx;
 	int ret;
+	unsigned long time_left;
 
 	tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
 	if (!tx) {
@@ -467,9 +468,9 @@
 	}
 
 	dma_async_issue_pending(chan);
-	ret = wait_for_completion_timeout(&qspi->transfer_complete,
+	time_left = wait_for_completion_timeout(&qspi->transfer_complete,
 					  msecs_to_jiffies(len));
-	if (ret <= 0) {
+	if (time_left == 0) {
 		dmaengine_terminate_sync(chan);
 		dev_err(qspi->dev, "DMA wait_for_completion_timeout\n");
 		return -ETIMEDOUT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-uniphier.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-uniphier.c
@@ -726,7 +726,7 @@
 		if (ret) {
 			dev_err(&pdev->dev, "failed to get TX DMA capacities: %d\n",
 				ret);
-			goto out_disable_clk;
+			goto out_release_dma;
 		}
 		dma_tx_burst = caps.max_burst;
 	}
@@ -735,7 +735,7 @@
 	if (IS_ERR_OR_NULL(master->dma_rx)) {
 		if (PTR_ERR(master->dma_rx) == -EPROBE_DEFER) {
 			ret = -EPROBE_DEFER;
-			goto out_disable_clk;
+			goto out_release_dma;
 		}
 		master->dma_rx = NULL;
 		dma_rx_burst = INT_MAX;
@@ -744,7 +744,7 @@
 		if (ret) {
 			dev_err(&pdev->dev, "failed to get RX DMA capacities: %d\n",
 				ret);
-			goto out_disable_clk;
+			goto out_release_dma;
 		}
 		dma_rx_burst = caps.max_burst;
 	}
@@ -753,10 +753,20 @@
 
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret)
-		goto out_disable_clk;
+		goto out_release_dma;
 
 	return 0;
 
+out_release_dma:
+	if (!IS_ERR_OR_NULL(master->dma_rx)) {
+		dma_release_channel(master->dma_rx);
+		master->dma_rx = NULL;
+	}
+	if (!IS_ERR_OR_NULL(master->dma_tx)) {
+		dma_release_channel(master->dma_tx);
+		master->dma_tx = NULL;
+	}
+
 out_disable_clk:
 	clk_disable_unprepare(priv->clk);
 
@@ -767,12 +777,13 @@
 
 static int uniphier_spi_remove(struct platform_device *pdev)
 {
-	struct uniphier_spi_priv *priv = platform_get_drvdata(pdev);
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct uniphier_spi_priv *priv = spi_master_get_devdata(master);
 
-	if (priv->master->dma_tx)
-		dma_release_channel(priv->master->dma_tx);
-	if (priv->master->dma_rx)
-		dma_release_channel(priv->master->dma_rx);
+	if (master->dma_tx)
+		dma_release_channel(master->dma_tx);
+	if (master->dma_rx)
+		dma_release_channel(master->dma_rx);
 
 	clk_disable_unprepare(priv->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-xilinx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-xilinx.c
@@ -16,10 +16,11 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
 #include <linux/spi/xilinx_spi.h>
 #include <linux/io.h>
-
+#include <linux/delay.h>
+#include <linux/pm_runtime.h>
+#include <linux/clk.h>
 #define XILINX_SPI_MAX_CS	32
 
 #define XILINX_SPI_NAME "xilinx_spi"
@@ -76,14 +77,51 @@
 #define XIPIF_V123B_RESETR_OFFSET	0x40	/* IPIF reset register */
 #define XIPIF_V123B_RESET_MASK		0x0a	/* the value to write */
 
+/* Number of bits per word */
+#define XSPI_ONE_BITS_PER_WORD 1
+#define XSPI_TWO_BITS_PER_WORD 2
+#define XSPI_FOUR_BITS_PER_WORD 4
+
+/* Number of data lines used to receive */
+#define XSPI_RX_ONE_WIRE	1
+#define XSPI_RX_FOUR_WIRE	4
+
+/* Auto suspend timeout in milliseconds */
+#define SPI_AUTOSUSPEND_TIMEOUT		3000
+
+/* Command used for Dummy read Id */
+#define SPI_READ_ID		0x9F
+
+/**
+ * struct xilinx_spi - This definition define spi driver instance
+ * @regs:		virt. address of the control registers
+ * @irq:		IRQ number
+ * @axi_clk:		Pointer to the AXI clock
+ * @axi4_clk:		Pointer to the AXI4 clock
+ * @spi_clk:		Pointer to the SPI clock
+ * @dev:		Pointer to the device
+ * @rx_ptr:		Pointer to the RX buffer
+ * @tx_ptr:		Pointer to the TX buffer
+ * @bytes_per_word:	Number of bytes in a word
+ * @buffer_size:	Buffer size in words
+ * @cs_inactive:	Level of the CS pins when inactive
+ * @read_fn:		For reading data from SPI registers
+ * @write_fn:		For writing data to SPI registers
+ * @bytes_to_transfer:	Number of bytes left to transfer
+ * @bytes_to_receive:	Number of bytes left to receive
+ * @rx_bus_width:	Number of wires used to receive data
+ * @tx_fifo:		For writing data to fifo
+ * @rx_fifo:		For reading data from fifo
+ */
 struct xilinx_spi {
-	/* bitbang has to be first */
-	struct spi_bitbang bitbang;
-	struct completion done;
 	void __iomem	*regs;	/* virt. address of the control registers */
 
 	int		irq;
 
+	struct clk *axi_clk;
+	struct clk *axi4_clk;
+	struct clk *spi_clk;
+	struct device *dev;
 	u8 *rx_ptr;		/* pointer in the Tx buffer */
 	const u8 *tx_ptr;	/* pointer in the Rx buffer */
 	u8 bytes_per_word;
@@ -91,8 +129,69 @@
 	u32 cs_inactive;	/* Level of the CS pins when inactive*/
 	unsigned int (*read_fn)(void __iomem *);
 	void (*write_fn)(u32, void __iomem *);
+	u32 bytes_to_transfer;
+	u32 bytes_to_receive;
+	u32 rx_bus_width;
+	void (*tx_fifo)(struct xilinx_spi *xqspi);
+	void (*rx_fifo)(struct xilinx_spi *xqspi);
 };
 
+/**
+ * XSPI_FIFO_READ - Generate xspi_read_rx_fifo_* functions
+ * @size: bits_per_word that are read from RX FIFO
+ * @type: C type of value argument
+ *
+ * Generates xspi_read_rx_fifo_* functions used to write
+ * data into RX FIFO for different transaction widths.
+ */
+#define XSPI_FIFO_READ(size, type)					\
+static void xspi_read_rx_fifo_##size(struct xilinx_spi *xqspi)		\
+{									\
+	int i;								\
+	int count = (xqspi->bytes_to_receive > xqspi->buffer_size) ?	\
+			xqspi->buffer_size : xqspi->bytes_to_receive;	\
+	u32 data;							\
+	for (i = 0; i < count; i += (size / 8)) {			\
+		data = readl_relaxed(xqspi->regs + XSPI_RXD_OFFSET);	\
+		if (xqspi->rx_ptr)					\
+			((type *)xqspi->rx_ptr)[i] = (type)data;	\
+	}								\
+	xqspi->bytes_to_receive -= count;				\
+	if (xqspi->rx_ptr)						\
+		xqspi->rx_ptr += count;					\
+}
+
+/**
+ * XSPI_FIFO_WRITE - Generate xspi_fill_tx_fifo_* functions
+ * @size: bits_per_word that are written into TX FIFO
+ * @type: C type of value argument
+ *
+ * Generates xspi_fill_tx_fifo_* functions used to write
+ * data into TX FIFO for different transaction widths.
+ */
+#define XSPI_FIFO_WRITE(size, type)					\
+static void xspi_fill_tx_fifo_##size(struct xilinx_spi *xqspi)		\
+{									\
+	int i;								\
+	int count = (xqspi->bytes_to_transfer > xqspi->buffer_size) ?	\
+			xqspi->buffer_size : xqspi->bytes_to_transfer;	\
+	u32 data = 0;							\
+	for (i = 0; i < count; i += (size / 8)) {			\
+		if (xqspi->tx_ptr)					\
+			data = *(type *)&xqspi->tx_ptr[i];		\
+		writel_relaxed(data, (xqspi->regs + XSPI_TXD_OFFSET));	\
+	}								\
+	xqspi->bytes_to_transfer -= count;				\
+	if (xqspi->tx_ptr)						\
+		xqspi->tx_ptr += count;					\
+}
+
+XSPI_FIFO_READ(8, u8)
+XSPI_FIFO_READ(16, u16)
+XSPI_FIFO_READ(32, u32)
+XSPI_FIFO_WRITE(8, u8)
+XSPI_FIFO_WRITE(16, u16)
+XSPI_FIFO_WRITE(32, u32)
 static void xspi_write32(u32 val, void __iomem *addr)
 {
 	iowrite32(val, addr);
@@ -113,53 +212,15 @@
 	return ioread32be(addr);
 }
 
-static void xilinx_spi_tx(struct xilinx_spi *xspi)
-{
-	u32 data = 0;
-
-	if (!xspi->tx_ptr) {
-		xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
-		return;
-	}
-
-	switch (xspi->bytes_per_word) {
-	case 1:
-		data = *(u8 *)(xspi->tx_ptr);
-		break;
-	case 2:
-		data = *(u16 *)(xspi->tx_ptr);
-		break;
-	case 4:
-		data = *(u32 *)(xspi->tx_ptr);
-		break;
-	}
-
-	xspi->write_fn(data, xspi->regs + XSPI_TXD_OFFSET);
-	xspi->tx_ptr += xspi->bytes_per_word;
-}
-
-static void xilinx_spi_rx(struct xilinx_spi *xspi)
-{
-	u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
-
-	if (!xspi->rx_ptr)
-		return;
-
-	switch (xspi->bytes_per_word) {
-	case 1:
-		*(u8 *)(xspi->rx_ptr) = data;
-		break;
-	case 2:
-		*(u16 *)(xspi->rx_ptr) = data;
-		break;
-	case 4:
-		*(u32 *)(xspi->rx_ptr) = data;
-		break;
-	}
-
-	xspi->rx_ptr += xspi->bytes_per_word;
-}
-
+/**
+ * xspi_init_hw - Initialize the hardware
+ * @xspi:	Pointer to the zynqmp_qspi structure
+ *
+ * This function performs the following actions
+ *	- Disable and clear all the interrupts
+ *	- Enable manual slave select
+ *	- Enable the SPI controller
+ */
 static void xspi_init_hw(struct xilinx_spi *xspi)
 {
 	void __iomem *regs_base = xspi->regs;
@@ -183,49 +244,106 @@
 		regs_base + XSPI_CR_OFFSET);
 }
 
-static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
+/**
+ * xspi_chipselect -	Select or deselect the chip select line
+ * @qspi:	Pointer to the spi_device structure
+ * @is_high:	Select(0) or deselect (1) the chip select line
+ *
+ */
+static void xspi_chipselect(struct spi_device *qspi, bool is_high)
 {
-	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
-	u16 cr;
+	struct xilinx_spi *xqspi = spi_master_get_devdata(qspi->master);
 	u32 cs;
 
-	if (is_on == BITBANG_CS_INACTIVE) {
-		/* Deselect the slave on the SPI bus */
-		xspi->write_fn(xspi->cs_inactive, xspi->regs + XSPI_SSR_OFFSET);
-		return;
+	if (is_high) {
+		/* Deselect the slave */
+		xqspi->write_fn(xqspi->cs_inactive,
+			xqspi->regs + XSPI_SSR_OFFSET);
+	} else {
+		cs = xqspi->cs_inactive;
+		cs ^= BIT(qspi->chip_select);
+		/* Activate the chip select */
+		xqspi->write_fn(cs, xqspi->regs + XSPI_SSR_OFFSET);
 	}
+}
 
-	/* Set the SPI clock phase and polarity */
-	cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET)	& ~XSPI_CR_MODE_MASK;
-	if (spi->mode & SPI_CPHA)
-		cr |= XSPI_CR_CPHA;
-	if (spi->mode & SPI_CPOL)
-		cr |= XSPI_CR_CPOL;
-	if (spi->mode & SPI_LSB_FIRST)
-		cr |= XSPI_CR_LSB_FIRST;
-	if (spi->mode & SPI_LOOP)
-		cr |= XSPI_CR_LOOP;
-	xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
-
-	/* We do not check spi->max_speed_hz here as the SPI clock
-	 * frequency is not software programmable (the IP block design
-	 * parameter)
-	 */
-
-	cs = xspi->cs_inactive;
-	cs ^= BIT(spi->chip_select);
+/**
+ * xilinx_spi_startup_block - Perform a dummy read as a
+ * work around for the startup block issue in the spi controller.
+ * @xspi:	Pointer to the xilinx_spi structure
+ * @cs_num:	chip select number.
+ *
+ * Perform a dummy read if startup block is enabled in the
+ * spi controller.
+ *
+ * Return:	None
+ */
+static void xilinx_spi_startup_block(struct xilinx_spi *xspi, u32 cs_num)
+{
+	void __iomem *regs_base = xspi->regs;
+	u32 chip_sel, config_reg, status_reg;
 
 	/* Activate the chip select */
-	xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET);
+	chip_sel = xspi->cs_inactive;
+	chip_sel ^= BIT(cs_num);
+	xspi->write_fn(chip_sel, regs_base + XSPI_SSR_OFFSET);
+
+	/* Write ReadId to the TXD register */
+	xspi->write_fn(SPI_READ_ID, regs_base + XSPI_TXD_OFFSET);
+	xspi->write_fn(0x0, regs_base + XSPI_TXD_OFFSET);
+	xspi->write_fn(0x0, regs_base + XSPI_TXD_OFFSET);
+
+	config_reg = xspi->read_fn(regs_base + XSPI_CR_OFFSET);
+	/* Enable master transaction  */
+	config_reg &= ~XSPI_CR_TRANS_INHIBIT;
+	xspi->write_fn(config_reg, regs_base + XSPI_CR_OFFSET);
+
+	status_reg = xspi->read_fn(regs_base + XSPI_SR_OFFSET);
+	while ((status_reg & XSPI_SR_TX_EMPTY_MASK) == 0)
+		status_reg = xspi->read_fn(regs_base + XSPI_SR_OFFSET);
+
+	/* Disable master transaction */
+	config_reg |= XSPI_CR_TRANS_INHIBIT;
+	xspi->write_fn(config_reg, regs_base + XSPI_CR_OFFSET);
+
+	/* Read the RXD Register */
+	status_reg = xspi->read_fn(regs_base + XSPI_SR_OFFSET);
+	while ((status_reg & XSPI_SR_RX_EMPTY_MASK) == 0) {
+		xspi->read_fn(regs_base + XSPI_RXD_OFFSET);
+		status_reg = xspi->read_fn(regs_base + XSPI_SR_OFFSET);
+	}
+
+	xspi_init_hw(xspi);
 }
 
-/* spi_bitbang requires custom setup_transfer() to be defined if there is a
- * custom txrx_bufs().
+/**
+ * xilinx_spi_setup_transfer - Configure SPI controller for specified
+ *			 transfer
+ * @spi:	Pointer to the spi_device structure
+ * @t:	Pointer to the spi_transfer structure which provides
+ *		information about next transfer setup parameters
+ *
+ * Sets the operational mode of QSPI controller for the next QSPI
+ * transfer.
+ *
+ * Return:	0 always
  */
 static int xilinx_spi_setup_transfer(struct spi_device *spi,
 		struct spi_transfer *t)
 {
 	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
+	u32 config_reg;
+
+	config_reg = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
+	/* Set the QSPI clock phase and clock polarity */
+	config_reg &= ~(XSPI_CR_CPHA | XSPI_CR_CPOL);
+	if (spi->mode & SPI_CPHA)
+		config_reg |= XSPI_CR_CPHA;
+	if (spi->mode & SPI_CPOL)
+		config_reg |= XSPI_CR_CPOL;
+	if (spi->mode & SPI_LSB_FIRST)
+		config_reg |= XSPI_CR_LSB_FIRST;
+	xspi->write_fn(config_reg, xspi->regs + XSPI_CR_OFFSET);
 
 	if (spi->mode & SPI_CS_HIGH)
 		xspi->cs_inactive &= ~BIT(spi->chip_select);
@@ -235,218 +353,425 @@
 	return 0;
 }
 
-static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
+/**
+ * xspi_setup -	Configure the SPI controller
+ * @qspi:	Pointer to the spi_device structure
+ *
+ * Sets the operational mode of QSPI controller for the next QSPI
+ * transfer.
+ *
+ * Return:	0 on success; error value otherwise.
+ */
+static int xspi_setup(struct spi_device *qspi)
 {
-	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
-	int remaining_words;	/* the number of words left to transfer */
-	bool use_irq = false;
-	u16 cr = 0;
-
-	/* We get here with transmitter inhibited */
-
-	xspi->tx_ptr = t->tx_buf;
-	xspi->rx_ptr = t->rx_buf;
-	remaining_words = t->len / xspi->bytes_per_word;
-
-	if (xspi->irq >= 0 &&  remaining_words > xspi->buffer_size) {
-		u32 isr;
-		use_irq = true;
-		/* Inhibit irq to avoid spurious irqs on tx_empty*/
-		cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
-		xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
-			       xspi->regs + XSPI_CR_OFFSET);
-		/* ACK old irqs (if any) */
-		isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
-		if (isr)
-			xspi->write_fn(isr,
-				       xspi->regs + XIPIF_V123B_IISR_OFFSET);
-		/* Enable the global IPIF interrupt */
-		xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
-				xspi->regs + XIPIF_V123B_DGIER_OFFSET);
-		reinit_completion(&xspi->done);
-	}
-
-	while (remaining_words) {
-		int n_words, tx_words, rx_words;
-		u32 sr;
-		int stalled;
-
-		n_words = min(remaining_words, xspi->buffer_size);
-
-		tx_words = n_words;
-		while (tx_words--)
-			xilinx_spi_tx(xspi);
+	int ret;
+	struct xilinx_spi *xqspi = spi_master_get_devdata(qspi->master);
 
-		/* Start the transfer by not inhibiting the transmitter any
-		 * longer
-		 */
+	if (qspi->master->busy)
+		return -EBUSY;
 
-		if (use_irq) {
-			xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
-			wait_for_completion(&xspi->done);
-			/* A transmit has just completed. Process received data
-			 * and check for more data to transmit. Always inhibit
-			 * the transmitter while the Isr refills the transmit
-			 * register/FIFO, or make sure it is stopped if we're
-			 * done.
-			 */
-			xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
-				       xspi->regs + XSPI_CR_OFFSET);
-			sr = XSPI_SR_TX_EMPTY_MASK;
-		} else
-			sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
-
-		/* Read out all the data from the Rx FIFO */
-		rx_words = n_words;
-		stalled = 10;
-		while (rx_words) {
-			if (rx_words == n_words && !(stalled--) &&
-			    !(sr & XSPI_SR_TX_EMPTY_MASK) &&
-			    (sr & XSPI_SR_RX_EMPTY_MASK)) {
-				dev_err(&spi->dev,
-					"Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n");
-				xspi_init_hw(xspi);
-				return -EIO;
-			}
-
-			if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
-				xilinx_spi_rx(xspi);
-				rx_words--;
-				continue;
-			}
-
-			sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
-			if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
-				xilinx_spi_rx(xspi);
-				rx_words--;
-			}
-		}
+	ret = pm_runtime_get_sync(xqspi->dev);
+	if (ret < 0)
+		return ret;
+
+	ret = xilinx_spi_setup_transfer(qspi, NULL);
+	pm_runtime_put_sync(xqspi->dev);
+
+	return ret;
+}
+
+/**
+ * xspi_start_transfer - Initiates the SPI transfer
+ * @master:	Pointer to the spi_master structure which provides
+ *		information about the controller.
+ * @qspi:	Pointer to the spi_device structure
+ * @transfer:	Pointer to the spi_transfer structure which provide information
+ *		about next transfer parameters
+ *
+ * This function fills the TX FIFO, starts the SPI transfer, and waits for the
+ * transfer to be completed.
+ *
+ * Return:	Number of bytes transferred in the last transfer
+ */
+
+static int xspi_start_transfer(struct spi_master *master,
+			       struct spi_device *qspi,
+			       struct spi_transfer *transfer)
+{
+	struct xilinx_spi *xqspi = spi_master_get_devdata(master);
+	u32 cr;
+
+	xqspi->tx_ptr = transfer->tx_buf;
+	xqspi->rx_ptr = transfer->rx_buf;
+
+	if (transfer->dummy) {
+		xqspi->bytes_to_transfer = (transfer->len - (transfer->dummy / 8))
+							+ ((transfer->dummy / 8) *
+							xqspi->rx_bus_width);
+		xqspi->bytes_to_receive = (transfer->len - (transfer->dummy / 8))
+							+ ((transfer->dummy / 8) *
+							xqspi->rx_bus_width);
+	} else {
+		xqspi->bytes_to_transfer = transfer->len;
+		xqspi->bytes_to_receive = transfer->len;
+	}
+
+	xilinx_spi_setup_transfer(qspi, transfer);
+	cr = xqspi->read_fn(xqspi->regs + XSPI_CR_OFFSET);
+	/* Enable master transaction inhibit */
+	cr |= XSPI_CR_TRANS_INHIBIT;
+	xqspi->write_fn(cr, xqspi->regs + XSPI_CR_OFFSET);
+	xqspi->tx_fifo(xqspi);
+	/* Disable master transaction inhibit */
+	cr &= ~XSPI_CR_TRANS_INHIBIT;
+	xqspi->write_fn(cr, xqspi->regs + XSPI_CR_OFFSET);
+	xqspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
+			xqspi->regs + XIPIF_V123B_DGIER_OFFSET);
+
+	return transfer->len;
+}
+
+/**
+ * xspi_prepare_transfer_hardware -	Prepares hardware for transfer.
+ * @master:	Pointer to the spi_master structure which provides
+ *		information about the controller.
+ *
+ * This function enables SPI master controller.
+ *
+ * Return:	0 on success; error value otherwise
+ */
+static int xspi_prepare_transfer_hardware(struct spi_master *master)
+{
+	struct xilinx_spi *xqspi = spi_master_get_devdata(master);
+
+	u32 cr;
+	int ret;
+
+	ret = pm_runtime_get_sync(xqspi->dev);
+	if (ret < 0)
+		return ret;
+
+	cr = xqspi->read_fn(xqspi->regs + XSPI_CR_OFFSET);
+	cr |= XSPI_CR_ENABLE;
+	xqspi->write_fn(cr, xqspi->regs + XSPI_CR_OFFSET);
+
+	return 0;
+}
+
+/**
+ * xspi_unprepare_transfer_hardware -	Relaxes hardware after transfer
+ * @master:	Pointer to the spi_master structure which provides
+ *		information about the controller.
+ *
+ * This function disables the SPI master controller.
+ *
+ * Return:	Always 0
+ */
+static int xspi_unprepare_transfer_hardware(struct spi_master *master)
+{
+	struct xilinx_spi *xqspi = spi_master_get_devdata(master);
+	u32 cr;
 
-		remaining_words -= n_words;
+	cr = xqspi->read_fn(xqspi->regs + XSPI_CR_OFFSET);
+	cr &= ~XSPI_CR_ENABLE;
+	xqspi->write_fn(cr, xqspi->regs + XSPI_CR_OFFSET);
+
+	pm_runtime_put_sync(xqspi->dev);
+
+	return 0;
+}
+
+/**
+ * xilinx_spi_runtime_resume - Runtime resume method for the SPI driver
+ * @dev:	Address of the platform_device structure
+ *
+ * This function enables the clocks
+ *
+ * Return:	0 on success and error value on error
+ */
+static int __maybe_unused xilinx_spi_runtime_resume(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct xilinx_spi *xspi = spi_master_get_devdata(master);
+	int ret;
+
+	ret = clk_enable(xspi->axi_clk);
+	if (ret) {
+		dev_err(dev, "Can not enable AXI clock\n");
+		return ret;
 	}
 
-	if (use_irq) {
-		xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
-		xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
+	ret = clk_enable(xspi->axi4_clk);
+	if (ret) {
+		dev_err(dev, "Can not enable AXI4 clock\n");
+		goto clk_disable_axi_clk;
+	}
+
+	ret = clk_enable(xspi->spi_clk);
+	if (ret) {
+		dev_err(dev, "Can not enable SPI clock\n");
+		goto clk_disable_axi4_clk;
 	}
 
-	return t->len;
+	return 0;
+
+clk_disable_axi4_clk:
+	clk_disable(xspi->axi4_clk);
+clk_disable_axi_clk:
+	clk_disable(xspi->axi_clk);
+
+	return ret;
 }
 
+/**
+ * xilinx_spi_runtime_suspend - Runtime suspend method for the SPI driver
+ * @dev:	Address of the platform_device structure
+ *
+ * This function disables the clocks
+ *
+ * Return:	Always 0
+ */
+static int __maybe_unused xilinx_spi_runtime_suspend(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct xilinx_spi *xspi = spi_master_get_devdata(master);
 
-/* This driver supports single master mode only. Hence Tx FIFO Empty
- * is the only interrupt we care about.
- * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
- * Fault are not to happen.
+	clk_disable(xspi->axi_clk);
+	clk_disable(xspi->axi4_clk);
+	clk_disable(xspi->spi_clk);
+
+	return 0;
+}
+
+/**
+ * xilinx_spi_resume - Resume method for the SPI driver
+ * @dev:	Address of the platform_device structure
+ *
+ * The function starts the SPI driver queue and initializes the SPI
+ * controller
+ *
+ * Return:	0 on success; error value otherwise
  */
-static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
+static int __maybe_unused xilinx_spi_resume(struct device *dev)
 {
-	struct xilinx_spi *xspi = dev_id;
-	u32 ipif_isr;
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct xilinx_spi *xspi = spi_master_get_devdata(master);
+	int ret = 0;
 
-	/* Get the IPIF interrupts, and clear them immediately */
-	ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
-	xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
+	if (!pm_runtime_suspended(dev)) {
+		ret = xilinx_spi_runtime_resume(dev);
+		if (ret < 0)
+			return ret;
+	}
 
-	if (ipif_isr & XSPI_INTR_TX_EMPTY) {	/* Transmission completed */
-		complete(&xspi->done);
-		return IRQ_HANDLED;
+	ret = spi_master_resume(master);
+	if (ret < 0) {
+		clk_disable(xspi->axi_clk);
+		clk_disable(xspi->axi4_clk);
+		clk_disable(xspi->spi_clk);
 	}
 
-	return IRQ_NONE;
+	return ret;
 }
 
-static int xilinx_spi_find_buffer_size(struct xilinx_spi *xspi)
+/**
+ * xilinx_spi_suspend - Suspend method for the SPI driver
+ * @dev:	Address of the platform_device structure
+ *
+ * This function stops the SPI driver queue and disables the SPI controller
+ *
+ * Return:	Always 0
+ */
+static int __maybe_unused xilinx_spi_suspend(struct device *dev)
 {
-	u8 sr;
-	int n_words = 0;
+	struct spi_master *master = dev_get_drvdata(dev);
+	int ret = 0;
 
-	/*
-	 * Before the buffer_size detection we reset the core
-	 * to make sure we start with a clean state.
-	 */
-	xspi->write_fn(XIPIF_V123B_RESET_MASK,
-		xspi->regs + XIPIF_V123B_RESETR_OFFSET);
+	ret = spi_master_suspend(master);
+	if (ret)
+		return ret;
+
+	if (!pm_runtime_suspended(dev))
+		xilinx_spi_runtime_suspend(dev);
 
-	/* Fill the Tx FIFO with as many words as possible */
-	do {
-		xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
-		sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
-		n_words++;
-	} while (!(sr & XSPI_SR_TX_FULL_MASK));
+	xspi_unprepare_transfer_hardware(master);
 
-	return n_words;
+	return ret;
 }
 
-static const struct of_device_id xilinx_spi_of_match[] = {
-	{ .compatible = "xlnx,axi-quad-spi-1.00.a", },
-	{ .compatible = "xlnx,xps-spi-2.00.a", },
-	{ .compatible = "xlnx,xps-spi-2.00.b", },
-	{}
+static const struct dev_pm_ops xilinx_spi_dev_pm_ops = {
+	SET_RUNTIME_PM_OPS(xilinx_spi_runtime_suspend,
+			   xilinx_spi_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(xilinx_spi_suspend, xilinx_spi_resume)
 };
-MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
 
-static int xilinx_spi_probe(struct platform_device *pdev)
+/* This driver supports single master mode only. Hence Tx FIFO Empty
+ * is the only interrupt we care about.
+ * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
+ * Fault are not to happen.
+ */
+static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
 {
-	struct xilinx_spi *xspi;
-	struct xspi_platform_data *pdata;
-	struct resource *res;
-	int ret, num_cs = 0, bits_per_word;
-	struct spi_master *master;
-	u32 tmp;
-	u8 i;
+	struct spi_master *master = dev_id;
+	struct xilinx_spi *xspi = spi_master_get_devdata(dev_id);
+	u32 ipif_isr;
+	irqreturn_t status = IRQ_NONE;
 
-	pdata = dev_get_platdata(&pdev->dev);
-	if (pdata) {
-		num_cs = pdata->num_chipselect;
-		bits_per_word = pdata->bits_per_word;
-	} else {
-		of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits",
-					  &num_cs);
-		ret = of_property_read_u32(pdev->dev.of_node,
-					   "xlnx,num-transfer-bits",
-					   &bits_per_word);
-		if (ret)
-			bits_per_word = 8;
+	/* Get the IPIF interrupts, and clear them immediately */
+	ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
+	xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
+	if (ipif_isr & XSPI_INTR_TX_EMPTY)  {
+		/* Transmission completed */
+		xspi->rx_fifo(xspi);
+		if (xspi->bytes_to_transfer) {
+			/* There is more data to send */
+			xspi->tx_fifo(xspi);
+		}
+		status = IRQ_HANDLED;
 	}
 
-	if (!num_cs) {
-		dev_err(&pdev->dev,
-			"Missing slave select configuration data\n");
-		return -EINVAL;
+	if (!xspi->bytes_to_receive && !xspi->bytes_to_transfer) {
+		spi_finalize_current_transfer(master);
+		/* Disable the interrupts here. */
+		xspi->write_fn(0x0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
 	}
 
+	return status;
+}
+static int xilinx_spi_probe(struct platform_device *pdev)
+{
+	struct xilinx_spi *xspi;
+	struct resource *res;
+	int ret;
+	u32 num_cs = 0, bits_per_word = 8;
+	u32 cs_num;
+	struct spi_master *master;
+	struct device_node *nc;
+	u32 tmp, rx_bus_width, fifo_size;
+	bool startup_block;
+
+	if (of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs))
+		dev_info(&pdev->dev,
+			 "Missing num-cs optional property, assuming default as <1>\n");
+	if (!num_cs)
+		num_cs = 1;
+
 	if (num_cs > XILINX_SPI_MAX_CS) {
 		dev_err(&pdev->dev, "Invalid number of spi slaves\n");
 		return -EINVAL;
 	}
 
+	startup_block = of_property_read_bool(pdev->dev.of_node,
+					      "xlnx,startup-block");
 	master = spi_alloc_master(&pdev->dev, sizeof(struct xilinx_spi));
 	if (!master)
 		return -ENODEV;
 
-	/* the spi->mode bits understood by this driver: */
-	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP |
-			    SPI_CS_HIGH;
-
 	xspi = spi_master_get_devdata(master);
-	xspi->cs_inactive = 0xffffffff;
-	xspi->bitbang.master = master;
-	xspi->bitbang.chipselect = xilinx_spi_chipselect;
-	xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
-	xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
-	init_completion(&xspi->done);
-
+	master->dev.of_node = pdev->dev.of_node;
+	platform_set_drvdata(pdev, master);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	xspi->regs = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(xspi->regs)) {
 		ret = PTR_ERR(xspi->regs);
 		goto put_master;
 	}
+	ret = of_property_read_u32(pdev->dev.of_node, "fifo-size",
+				   &fifo_size);
+	if (ret < 0) {
+		dev_err(&pdev->dev,
+			"Missing fifo size\n");
+		return -EINVAL;
+	}
+	if (of_property_read_u32(pdev->dev.of_node, "bits-per-word",
+				 &bits_per_word))
+		dev_info(&pdev->dev,
+			 "Missing bits-per-word optional property, assuming default as <8>\n");
+
+	xspi->rx_bus_width = XSPI_ONE_BITS_PER_WORD;
+	for_each_available_child_of_node(pdev->dev.of_node, nc) {
+		if (startup_block) {
+			ret = of_property_read_u32(nc, "reg",
+						   &cs_num);
+			if (ret < 0)
+				return -EINVAL;
+		}
+		ret = of_property_read_u32(nc, "spi-rx-bus-width",
+					   &rx_bus_width);
+		if (!ret) {
+			xspi->rx_bus_width = rx_bus_width;
+			break;
+		}
+	}
 
-	master->bus_num = pdev->id;
-	master->num_chipselect = num_cs;
-	master->dev.of_node = pdev->dev.of_node;
+	xspi->axi_clk = devm_clk_get(&pdev->dev, "axi_clk");
+	if (IS_ERR(xspi->axi_clk)) {
+		if (PTR_ERR(xspi->axi_clk) != -ENOENT) {
+			ret = PTR_ERR(xspi->axi_clk);
+			goto put_master;
+		}
+
+		/*
+		 * Clock framework support is optional, continue on,
+		 * anyways if we don't find a matching clock
+		 */
+		xspi->axi_clk = NULL;
+	}
+
+	ret = clk_prepare(xspi->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to prepare AXI clock\n");
+		goto put_master;
+	}
+
+	xspi->axi4_clk = devm_clk_get(&pdev->dev, "axi4_clk");
+	if (IS_ERR(xspi->axi4_clk)) {
+		if (PTR_ERR(xspi->axi4_clk) != -ENOENT) {
+			ret = PTR_ERR(xspi->axi4_clk);
+			goto clk_unprepare_axi_clk;
+		}
+
+		/*
+		 * Clock framework support is optional, continue on,
+		 * anyways if we don't find a matching clock
+		 */
+		xspi->axi4_clk = NULL;
+	}
+
+	ret = clk_prepare(xspi->axi4_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to prepare AXI4 clock\n");
+		goto clk_unprepare_axi_clk;
+	}
+
+	xspi->spi_clk = devm_clk_get(&pdev->dev, "spi_clk");
+	if (IS_ERR(xspi->spi_clk)) {
+		if (PTR_ERR(xspi->spi_clk) != -ENOENT) {
+			ret = PTR_ERR(xspi->spi_clk);
+			goto clk_unprepare_axi4_clk;
+		}
+
+		/*
+		 * Clock framework support is optional, continue on,
+		 * anyways if we don't find a matching clock
+		 */
+		xspi->spi_clk = NULL;
+	}
+
+	ret = clk_prepare(xspi->spi_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to prepare SPI clock\n");
+		goto clk_unprepare_axi4_clk;
+	}
+
+	pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	ret = pm_runtime_get_sync(&pdev->dev);
+	if (ret < 0)
+		goto clk_unprepare_all;
+
+	xspi->dev = &pdev->dev;
 
 	/*
 	 * Detect endianess on the IP via loop bit in CR. Detection
@@ -466,61 +791,112 @@
 		xspi->write_fn = xspi_write32_be;
 	}
 
-	master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word);
-	xspi->bytes_per_word = bits_per_word / 8;
-	xspi->buffer_size = xilinx_spi_find_buffer_size(xspi);
-
+	xspi->buffer_size = fifo_size;
 	xspi->irq = platform_get_irq(pdev, 0);
 	if (xspi->irq < 0 && xspi->irq != -ENXIO) {
 		ret = xspi->irq;
-		goto put_master;
+		goto clk_unprepare_all;
 	} else if (xspi->irq >= 0) {
 		/* Register for SPI Interrupt */
-		ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0,
-				dev_name(&pdev->dev), xspi);
+		ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq,
+				       0, dev_name(&pdev->dev), master);
 		if (ret)
-			goto put_master;
+			goto clk_unprepare_all;
 	}
 
 	/* SPI controller initializations */
 	xspi_init_hw(xspi);
 
-	ret = spi_bitbang_start(&xspi->bitbang);
-	if (ret) {
-		dev_err(&pdev->dev, "spi_bitbang_start FAILED\n");
-		goto put_master;
+	pm_runtime_put(&pdev->dev);
+
+	master->bus_num = pdev->id;
+	master->num_chipselect = num_cs;
+	master->setup = xspi_setup;
+	master->set_cs = xspi_chipselect;
+	master->transfer_one = xspi_start_transfer;
+	master->prepare_transfer_hardware = xspi_prepare_transfer_hardware;
+	master->unprepare_transfer_hardware = xspi_unprepare_transfer_hardware;
+	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+
+	xspi->bytes_per_word = bits_per_word / 8;
+	xspi->tx_fifo = xspi_fill_tx_fifo_8;
+	xspi->rx_fifo = xspi_read_rx_fifo_8;
+	if (xspi->rx_bus_width == XSPI_RX_ONE_WIRE) {
+		if (xspi->bytes_per_word == XSPI_TWO_BITS_PER_WORD) {
+			xspi->tx_fifo = xspi_fill_tx_fifo_16;
+			xspi->rx_fifo = xspi_read_rx_fifo_16;
+		} else if (xspi->bytes_per_word == XSPI_FOUR_BITS_PER_WORD) {
+			xspi->tx_fifo = xspi_fill_tx_fifo_32;
+			xspi->rx_fifo = xspi_read_rx_fifo_32;
+		}
+	} else if (xspi->rx_bus_width == XSPI_RX_FOUR_WIRE) {
+		master->mode_bits |= SPI_TX_QUAD | SPI_RX_QUAD;
+	} else {
+		dev_err(&pdev->dev, "Dual Mode not supported\n");
+		goto clk_unprepare_all;
 	}
+	xspi->cs_inactive = 0xffffffff;
 
-	dev_info(&pdev->dev, "at %pR, irq=%d\n", res, xspi->irq);
+	/*
+	 * This is the work around for the startup block issue in
+	 * the spi controller. SPI clock is passing through STARTUP
+	 * block to FLASH. STARTUP block don't provide clock as soon
+	 * as QSPI provides command. So first command fails.
+	 */
+	if (startup_block)
+		xilinx_spi_startup_block(xspi, cs_num);
 
-	if (pdata) {
-		for (i = 0; i < pdata->num_devices; i++)
-			spi_new_device(master, pdata->devices + i);
+	ret = spi_register_master(master);
+	if (ret) {
+		dev_err(&pdev->dev, "spi_register_master failed\n");
+		goto clk_unprepare_all;
 	}
 
-	platform_set_drvdata(pdev, master);
-	return 0;
+	return ret;
 
+clk_unprepare_all:
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	clk_unprepare(xspi->spi_clk);
+clk_unprepare_axi4_clk:
+	clk_unprepare(xspi->axi4_clk);
+clk_unprepare_axi_clk:
+	clk_unprepare(xspi->axi_clk);
 put_master:
 	spi_master_put(master);
 
 	return ret;
 }
 
+/**
+ * xilinx_spi_remove -	Remove method for the SPI driver
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * This function is called if a device is physically removed from the system or
+ * if the driver module is being unloaded. It frees all resources allocated to
+ * the device.
+ *
+ * Return:	0 Always
+ */
 static int xilinx_spi_remove(struct platform_device *pdev)
 {
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct xilinx_spi *xspi = spi_master_get_devdata(master);
 	void __iomem *regs_base = xspi->regs;
 
-	spi_bitbang_stop(&xspi->bitbang);
-
 	/* Disable all the interrupts just in case */
 	xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
 	/* Disable the global IPIF interrupt */
 	xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
 
-	spi_master_put(xspi->bitbang.master);
+	pm_runtime_disable(&pdev->dev);
+
+	clk_disable_unprepare(xspi->axi_clk);
+	clk_disable_unprepare(xspi->axi4_clk);
+	clk_disable_unprepare(xspi->spi_clk);
+
+	spi_unregister_master(master);
 
 	return 0;
 }
@@ -528,12 +904,21 @@
 /* work with hotplug and coldplug */
 MODULE_ALIAS("platform:" XILINX_SPI_NAME);
 
+static const struct of_device_id xilinx_spi_of_match[] = {
+	{ .compatible = "xlnx,axi-quad-spi-1.00.a", },
+	{ .compatible = "xlnx,xps-spi-2.00.a", },
+	{ .compatible = "xlnx,xps-spi-2.00.b", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
+
 static struct platform_driver xilinx_spi_driver = {
 	.probe = xilinx_spi_probe,
 	.remove = xilinx_spi_remove,
 	.driver = {
 		.name = XILINX_SPI_NAME,
 		.of_match_table = xilinx_spi_of_match,
+		.pm = &xilinx_spi_dev_pm_ops,
 	},
 };
 module_platform_driver(xilinx_spi_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-zynq-qspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-zynq-qspi.c
@@ -62,6 +62,7 @@
 #define ZYNQ_QSPI_CONFIG_BAUD_DIV_MAX	GENMASK(2, 0) /* Baud rate maximum */
 #define ZYNQ_QSPI_CONFIG_BAUD_DIV_SHIFT	3 /* Baud rate divisor shift */
 #define ZYNQ_QSPI_CONFIG_PCS		BIT(10) /* Peripheral Chip Select */
+#define ZYNQ_QSPI_SS_SHIFT		10 /* Slave Select field shift in CR */
 
 /*
  * QSPI Interrupt Registers bit Masks
@@ -117,6 +118,9 @@
 /* Maximum number of chip selects */
 #define ZYNQ_QSPI_MAX_NUM_CS		2
 
+/* Maximum address width */
+#define ZYNQ_QSPI_MAX_ADDR_WIDTH	3
+
 /**
  * struct zynq_qspi - Defines qspi driver instance
  * @dev:		Pointer to the this device's information
@@ -129,6 +133,9 @@
  * @tx_bytes:		Number of bytes left to transfer
  * @rx_bytes:		Number of bytes left to receive
  * @data_completion:	completion structure
+ * @is_dual:		Flag to indicate whether dual flash memories are used
+ * @is_stripe:		Flag to indicate if data needs to be split between flashes
+ *			(Used in dual parallel configuration)
  */
 struct zynq_qspi {
 	struct device *dev;
@@ -141,6 +148,8 @@
 	int tx_bytes;
 	int rx_bytes;
 	struct completion data_completion;
+	u32 is_dual;
+	bool is_stripe;
 };
 
 /*
@@ -185,13 +194,7 @@
 	zynq_qspi_write(xqspi, ZYNQ_QSPI_ENABLE_OFFSET, 0);
 	zynq_qspi_write(xqspi, ZYNQ_QSPI_IDIS_OFFSET, ZYNQ_QSPI_IXR_ALL_MASK);
 
-	/* Disable linear mode as the boot loader may have used it */
-	config_reg = 0;
-	/* At the same time, enable dual mode if more than 1 CS is available */
-	if (num_cs > 1)
-		config_reg |= ZYNQ_QSPI_LCFG_TWO_MEM;
-
-	zynq_qspi_write(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET, config_reg);
+	zynq_qspi_write(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET, 0);
 
 	/* Clear the RX FIFO */
 	while (zynq_qspi_read(xqspi, ZYNQ_QSPI_STATUS_OFFSET) &
@@ -217,7 +220,20 @@
 			ZYNQ_QSPI_RX_THRESHOLD);
 	zynq_qspi_write(xqspi, ZYNQ_QSPI_TX_THRESH_OFFSET,
 			ZYNQ_QSPI_TX_THRESHOLD);
-
+	if (xqspi->is_dual)
+		/* Enable two memories on separate buses */
+		zynq_qspi_write(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET,
+				(ZYNQ_QSPI_LCFG_TWO_MEM |
+				ZYNQ_QSPI_LCFG_SEP_BUS |
+				(1 << ZYNQ_QSPI_LCFG_DUMMY_SHIFT) |
+				ZYNQ_QSPI_FAST_READ_QOUT_CODE));
+#ifdef CONFIG_SPI_ZYNQ_QSPI_DUAL_STACKED
+	/* Enable two memories on shared bus */
+	zynq_qspi_write(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET,
+			(ZYNQ_QSPI_LCFG_TWO_MEM |
+			(1 << ZYNQ_QSPI_LCFG_DUMMY_SHIFT) |
+			ZYNQ_QSPI_FAST_READ_QOUT_CODE));
+#endif
 	zynq_qspi_write(xqspi, ZYNQ_QSPI_ENABLE_OFFSET,
 			ZYNQ_QSPI_ENABLE_ENABLE_MASK);
 }
@@ -227,13 +243,6 @@
 {
 	if (!spi_mem_default_supports_op(mem, op))
 		return false;
-
-	/*
-	 * The number of address bytes should be equal to or less than 3 bytes.
-	 */
-	if (op->addr.nbytes > 3)
-		return false;
-
 	return true;
 }
 
@@ -245,11 +254,15 @@
 static void zynq_qspi_rxfifo_op(struct zynq_qspi *xqspi, unsigned int size)
 {
 	u32 data;
+	unsigned int xsize;
 
 	data = zynq_qspi_read(xqspi, ZYNQ_QSPI_RXD_OFFSET);
 
 	if (xqspi->rxbuf) {
-		memcpy(xqspi->rxbuf, ((u8 *)&data) + 4 - size, size);
+		xsize = size;
+		if (xqspi->is_dual && xqspi->is_stripe && (size % 2))
+			xsize++;
+		memcpy(xqspi->rxbuf, ((u8 *)&data) + 4 - xsize, size);
 		xqspi->rxbuf += size;
 	}
 
@@ -269,6 +282,7 @@
 		ZYNQ_QSPI_TXD_00_01_OFFSET, ZYNQ_QSPI_TXD_00_10_OFFSET,
 		ZYNQ_QSPI_TXD_00_11_OFFSET, ZYNQ_QSPI_TXD_00_00_OFFSET };
 	u32 data;
+	unsigned int xsize;
 
 	if (xqspi->txbuf) {
 		data = 0xffffffff;
@@ -279,7 +293,11 @@
 	}
 
 	xqspi->tx_bytes -= size;
-	zynq_qspi_write(xqspi, offset[size - 1], data);
+	xsize = size;
+	if (xqspi->is_dual && xqspi->is_stripe && (size % 2))
+		xsize++;
+
+	zynq_qspi_write(xqspi, offset[xsize - 1], data);
 }
 
 /**
@@ -292,25 +310,29 @@
 	struct spi_controller *ctlr = spi->master;
 	struct zynq_qspi *xqspi = spi_controller_get_devdata(ctlr);
 	u32 config_reg;
+#ifdef CONFIG_SPI_ZYNQ_QSPI_DUAL_STACKED
+	u32 lqspi_cfg_reg;
+#endif
 
-	/* Select the lower (CS0) or upper (CS1) memory */
-	if (ctlr->num_chipselect > 1) {
-		config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET);
-		if (!spi->chip_select)
-			config_reg &= ~ZYNQ_QSPI_LCFG_U_PAGE;
-		else
-			config_reg |= ZYNQ_QSPI_LCFG_U_PAGE;
-
-		zynq_qspi_write(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET, config_reg);
-	}
+	config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET);
 
+#ifdef CONFIG_SPI_ZYNQ_QSPI_DUAL_STACKED
+	lqspi_cfg_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET);
+		if (spi->master->flags & SPI_MASTER_U_PAGE)
+			lqspi_cfg_reg |= ZYNQ_QSPI_LCFG_U_PAGE;
+		else
+			lqspi_cfg_reg &= ~ZYNQ_QSPI_LCFG_U_PAGE;
+		zynq_qspi_write(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET,
+				lqspi_cfg_reg);
+#endif
 	/* Ground the line to assert the CS */
-	config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET);
-	if (assert)
+	if (assert) {
 		config_reg &= ~ZYNQ_QSPI_CONFIG_PCS;
-	else
+		config_reg |= (((~(BIT(spi->chip_select))) <<
+			       ZYNQ_QSPI_SS_SHIFT) & ZYNQ_QSPI_CONFIG_PCS);
+	} else {
 		config_reg |= ZYNQ_QSPI_CONFIG_PCS;
-
+	}
 	zynq_qspi_write(xqspi, ZYNQ_QSPI_CONFIG_OFFSET, config_reg);
 }
 
@@ -379,12 +401,21 @@
 {
 	struct spi_controller *ctlr = spi->master;
 	struct zynq_qspi *qspi = spi_controller_get_devdata(ctlr);
+	int ret;
 
 	if (ctlr->busy)
 		return -EBUSY;
 
-	clk_enable(qspi->refclk);
-	clk_enable(qspi->pclk);
+	ret = clk_enable(qspi->refclk);
+	if (ret)
+		return ret;
+
+	ret = clk_enable(qspi->pclk);
+	if (ret) {
+		clk_disable(qspi->refclk);
+		return ret;
+	}
+
 	zynq_qspi_write(qspi, ZYNQ_QSPI_ENABLE_OFFSET,
 			ZYNQ_QSPI_ENABLE_ENABLE_MASK);
 
@@ -520,7 +551,8 @@
  *
  * This function first selects the chip and starts the memory operation.
  *
- * Return: 0 in case of success, a negative error code otherwise.
+ * Return: 0 in case of success, -EINVAL if address size greater than
+ * ZYNQ_QSPI_MAX_ADDR_WIDTH.
  */
 static int zynq_qspi_exec_mem_op(struct spi_mem *mem,
 				 const struct spi_mem_op *op)
@@ -528,11 +560,15 @@
 	struct zynq_qspi *xqspi = spi_controller_get_devdata(mem->spi->master);
 	int err = 0, i;
 	u8 *tmpbuf;
+	u8 opaddr[ZYNQ_QSPI_MAX_ADDR_WIDTH];
 
 	dev_dbg(xqspi->dev, "cmd:%#x mode:%d.%d.%d.%d\n",
 		op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
 		op->dummy.buswidth, op->data.buswidth);
 
+	if (op->addr.nbytes > ZYNQ_QSPI_MAX_ADDR_WIDTH)
+		return -EINVAL;
+
 	zynq_qspi_chipselect(mem->spi, true);
 	zynq_qspi_config_op(xqspi, mem->spi);
 
@@ -551,6 +587,7 @@
 	}
 
 	if (op->addr.nbytes) {
+		xqspi->txbuf = opaddr;
 		for (i = 0; i < op->addr.nbytes; i++) {
 			xqspi->txbuf[i] = op->addr.val >>
 					(8 * (op->addr.nbytes - i - 1));
@@ -570,6 +607,9 @@
 
 	if (op->dummy.nbytes) {
 		tmpbuf = kzalloc(op->dummy.nbytes, GFP_KERNEL);
+		if (!tmpbuf)
+			return -ENOMEM;
+
 		memset(tmpbuf, 0xff, op->dummy.nbytes);
 		reinit_completion(&xqspi->data_completion);
 		xqspi->txbuf = tmpbuf;
@@ -587,6 +627,8 @@
 	}
 
 	if (op->data.nbytes) {
+		if (xqspi->is_dual)
+			xqspi->is_stripe = update_stripe(op);
 		reinit_completion(&xqspi->data_completion);
 		if (op->data.dir == SPI_MEM_DATA_OUT) {
 			xqspi->txbuf = (u8 *)op->data.buf.out;
@@ -607,6 +649,9 @@
 							       msecs_to_jiffies(1000)))
 			err = -ETIMEDOUT;
 	}
+	if (xqspi->is_stripe)
+		xqspi->is_stripe = false;
+
 	zynq_qspi_chipselect(mem->spi, false);
 
 	return err;
@@ -647,6 +692,11 @@
 		goto remove_master;
 	}
 
+	if (of_property_read_u32(pdev->dev.of_node, "is-dual",
+				 &xqspi->is_dual)) {
+		dev_warn(&pdev->dev, "couldn't determine configuration info");
+		dev_warn(&pdev->dev, "about dual memories. defaulting to single memory\n");
+	}
 	xqspi->pclk = devm_clk_get(&pdev->dev, "pclk");
 	if (IS_ERR(xqspi->pclk)) {
 		dev_err(&pdev->dev, "pclk clock not found.\n");
@@ -700,7 +750,7 @@
 		ctlr->num_chipselect = num_cs;
 	}
 
-	ctlr->mode_bits =  SPI_RX_DUAL | SPI_RX_QUAD |
+	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
 			    SPI_TX_DUAL | SPI_TX_QUAD;
 	ctlr->mem_ops = &zynq_qspi_mem_ops;
 	ctlr->setup = zynq_qspi_setup_op;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi-zynqmp-gqspi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi-zynqmp-gqspi.c
@@ -16,12 +16,14 @@
 #include <linux/module.h>
 #include <linux/of_irq.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/spi/spi.h>
 #include <linux/spinlock.h>
 #include <linux/workqueue.h>
 #include <linux/spi/spi-mem.h>
+#include <linux/mtd/spi-nor.h>
 
 /* Generic QSPI register offsets */
 #define GQSPI_CONFIG_OFST		0x00000100
@@ -34,6 +36,7 @@
 #define GQSPI_RXD_OFST			0x00000120
 #define GQSPI_TX_THRESHOLD_OFST		0x00000128
 #define GQSPI_RX_THRESHOLD_OFST		0x0000012C
+#define IOU_TAPDLY_BYPASS_OFST		0x0000003C
 #define GQSPI_LPBK_DLY_ADJ_OFST		0x00000138
 #define GQSPI_GEN_FIFO_OFST		0x00000140
 #define GQSPI_SEL_OFST			0x00000144
@@ -48,6 +51,7 @@
 #define GQSPI_QSPIDMA_DST_I_MASK_OFST	0x00000820
 #define GQSPI_QSPIDMA_DST_ADDR_OFST	0x00000800
 #define GQSPI_QSPIDMA_DST_ADDR_MSB_OFST 0x00000828
+#define GQSPI_DATA_DLY_ADJ_OFST		0x000001F8
 
 /* GQSPI register bit masks */
 #define GQSPI_SEL_MASK				0x00000001
@@ -133,11 +137,44 @@
 #define GQSPI_SELECT_MODE_QUADSPI	0x4
 #define GQSPI_DMA_UNALIGN		0x3
 #define GQSPI_DEFAULT_NUM_CS	1	/* Default number of chip selects */
+#define GQSPI_RX_BUS_WIDTH_QUAD		0x4
+#define GQSPI_RX_BUS_WIDTH_DUAL		0x2
+#define GQSPI_RX_BUS_WIDTH_SINGLE	0x1
+#define GQSPI_TX_BUS_WIDTH_QUAD		0x4
+#define GQSPI_TX_BUS_WIDTH_DUAL		0x2
+#define GQSPI_TX_BUS_WIDTH_SINGLE	0x1
+#define GQSPI_LPBK_DLY_ADJ_LPBK_SHIFT	5
+#define GQSPI_LPBK_DLY_ADJ_DLY_1	0x1
+#define GQSPI_LPBK_DLY_ADJ_DLY_1_SHIFT	3
+#define GQSPI_LPBK_DLY_ADJ_DLY_0	0x3
+#define GQSPI_USE_DATA_DLY		0x1
+#define GQSPI_USE_DATA_DLY_SHIFT	31
+#define GQSPI_DATA_DLY_ADJ_VALUE	0x2
+#define GQSPI_DATA_DLY_ADJ_SHIFT	28
+#define TAP_DLY_BYPASS_LQSPI_RX_VALUE	0x1
+#define TAP_DLY_BYPASS_LQSPI_RX_SHIFT	2
+
+/* set to differentiate versal from zynqmp, 1=versal, 0=zynqmp */
+#define QSPI_QUIRK_HAS_TAPDELAY	BIT(0)
+
+#define GQSPI_FREQ_37_5MHZ	37500000
+#define GQSPI_FREQ_40MHZ	40000000
+#define GQSPI_FREQ_100MHZ	100000000
+#define GQSPI_FREQ_150MHZ	150000000
+#define IOU_TAPDLY_BYPASS_MASK	0x7
 
 #define SPI_AUTOSUSPEND_TIMEOUT		3000
 enum mode_type {GQSPI_MODE_IO, GQSPI_MODE_DMA};
 
 /**
+ * struct qspi_platform_data - zynqmp qspi platform data structure
+ * @quirks:	Flags is used to identify the platform
+ */
+struct qspi_platform_data {
+	u32 quirks;
+};
+
+/**
  * struct zynqmp_qspi - Defines qspi driver instance
  * @regs:		Virtual address of the QSPI controller registers
  * @refclk:		Pointer to the peripheral clock
@@ -152,9 +189,15 @@
  * @genfifobus:		Used to select the upper or lower bus
  * @dma_rx_bytes:	Remaining bytes to receive by DMA mode
  * @dma_addr:		DMA address after mapping the kernel buffer
+ * @tx_bus_width:	Used to represent number of data wires for tx
+ * @rx_bus_width:	Used to represent number of data wires
  * @genfifoentry:	Used for storing the genfifoentry instruction.
  * @mode:		Defines the mode in which QSPI is operating
+ * @speed_hz:		Current SPI bus clock speed in hz
+ * @io_mode:		Defines the operating mode, either IO or dma
+ * @has_tapdelay:	Used for tapdelay register available in qspi
  * @data_completion:	completion structure
+ * @op_lock:		Operational lock
  */
 struct zynqmp_qspi {
 	struct spi_controller *ctlr;
@@ -171,13 +214,40 @@
 	u32 genfifobus;
 	u32 dma_rx_bytes;
 	dma_addr_t dma_addr;
+	u32 rx_bus_width;
+	u32 tx_bus_width;
 	u32 genfifoentry;
 	enum mode_type mode;
+	u32 speed_hz;
+	bool io_mode;
+	bool has_tapdelay;
 	struct completion data_completion;
 	struct mutex op_lock;
 };
 
 /**
+ * zynqmp_get_addr_buswidth - Get address buswidth
+ * @op:	The memory operation to execute
+ *
+ * This function gets address busswith
+ *
+ * Return:	buswidth
+ */
+static u8 zynqmp_get_addr_buswidth(const struct spi_mem_op *op)
+{
+	if (op->cmd.opcode == SPINOR_OP_BE_4K ||
+	    op->cmd.opcode == SPINOR_OP_BE_32K ||
+	    op->cmd.opcode == SPINOR_OP_CHIP_ERASE ||
+	    op->cmd.opcode == SPINOR_OP_SE ||
+	    op->cmd.opcode == SPINOR_OP_BE_4K_4B ||
+	    op->cmd.opcode == SPINOR_OP_BE_32K_4B ||
+	    op->cmd.opcode == SPINOR_OP_SE_4B)
+		return op->cmd.buswidth;
+	else
+		return op->addr.buswidth;
+}
+
+/**
  * zynqmp_gqspi_read - For GQSPI controller read operation
  * @xqspi:	Pointer to the zynqmp_qspi structure
  * @offset:	Offset from where to read
@@ -248,6 +318,70 @@
 }
 
 /**
+ * zynqmp_qspi_set_tapdelay:	To configure qspi tap delays
+ * @xqspi:		Pointer to the zynqmp_qspi structure
+ * @baudrateval:	Buadrate to configure
+ */
+static void zynqmp_qspi_set_tapdelay(struct zynqmp_qspi *xqspi, u32 baudrateval)
+{
+	u32 tapdlybypass = 0, lpbkdlyadj = 0, datadlyadj = 0, clk_rate;
+	u32 reqhz = 0;
+
+	clk_rate = clk_get_rate(xqspi->refclk);
+	reqhz = (clk_rate / (GQSPI_BAUD_DIV_SHIFT << baudrateval));
+
+	if (!xqspi->has_tapdelay) {
+		if (reqhz <= GQSPI_FREQ_40MHZ) {
+			zynqmp_pm_set_tapdelay_bypass(
+					   PM_TAPDELAY_QSPI,
+					   PM_TAPDELAY_BYPASS_ENABLE);
+		} else if (reqhz <= GQSPI_FREQ_100MHZ) {
+			zynqmp_pm_set_tapdelay_bypass(
+					   PM_TAPDELAY_QSPI,
+					   PM_TAPDELAY_BYPASS_ENABLE);
+			lpbkdlyadj |= (GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
+			datadlyadj |= ((GQSPI_USE_DATA_DLY <<
+					GQSPI_USE_DATA_DLY_SHIFT)
+					| (GQSPI_DATA_DLY_ADJ_VALUE <<
+						GQSPI_DATA_DLY_ADJ_SHIFT));
+		} else if (reqhz <= GQSPI_FREQ_150MHZ) {
+			lpbkdlyadj |= GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK;
+		}
+	} else {
+		if (reqhz <= GQSPI_FREQ_37_5MHZ) {
+			tapdlybypass |= (TAP_DLY_BYPASS_LQSPI_RX_VALUE <<
+					TAP_DLY_BYPASS_LQSPI_RX_SHIFT);
+		} else if (reqhz <= GQSPI_FREQ_100MHZ) {
+			tapdlybypass |= (TAP_DLY_BYPASS_LQSPI_RX_VALUE <<
+					TAP_DLY_BYPASS_LQSPI_RX_SHIFT);
+			lpbkdlyadj |= (GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
+			datadlyadj |= (GQSPI_USE_DATA_DLY <<
+					GQSPI_USE_DATA_DLY_SHIFT);
+		} else if (reqhz <= GQSPI_FREQ_150MHZ) {
+			lpbkdlyadj |= (GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK
+				       | (GQSPI_LPBK_DLY_ADJ_DLY_1 <<
+					       GQSPI_LPBK_DLY_ADJ_DLY_1_SHIFT));
+		}
+		zynqmp_gqspi_write(xqspi,
+				   IOU_TAPDLY_BYPASS_OFST, tapdlybypass);
+	}
+
+	zynqmp_gqspi_write(xqspi, GQSPI_LPBK_DLY_ADJ_OFST, lpbkdlyadj);
+	zynqmp_gqspi_write(xqspi, GQSPI_DATA_DLY_ADJ_OFST, datadlyadj);
+}
+
+static u32 zynqmp_disable_intr(struct zynqmp_qspi *xqspi)
+{
+	u32 value;
+
+	zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_ISR_IDR_MASK);
+	value = zynqmp_gqspi_read(xqspi, GQSPI_IMASK_OFST);
+	zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_ISR_IDR_MASK);
+
+	return value;
+}
+
+/**
  * zynqmp_qspi_init_hw - Initialize the hardware
  * @xqspi:	Pointer to the zynqmp_qspi structure
  *
@@ -268,13 +402,13 @@
 static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi)
 {
 	u32 config_reg;
+	u32 baud_rate_val = 0;
+	ulong clk_rate = clk_get_rate(xqspi->refclk);
 
 	/* Select the GQSPI mode */
 	zynqmp_gqspi_write(xqspi, GQSPI_SEL_OFST, GQSPI_SEL_MASK);
 	/* Clear and disable interrupts */
-	zynqmp_gqspi_write(xqspi, GQSPI_ISR_OFST,
-			   zynqmp_gqspi_read(xqspi, GQSPI_ISR_OFST) |
-			   GQSPI_ISR_WR_TO_CLR_MASK);
+	zynqmp_disable_intr(xqspi);
 	/* Clear the DMA STS */
 	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_I_STS_OFST,
 			   zynqmp_gqspi_read(xqspi,
@@ -313,9 +447,11 @@
 			   GQSPI_FIFO_CTRL_RST_TX_FIFO_MASK |
 			   GQSPI_FIFO_CTRL_RST_GEN_FIFO_MASK);
 	/* Set by default to allow for high frequencies */
-	zynqmp_gqspi_write(xqspi, GQSPI_LPBK_DLY_ADJ_OFST,
-			   zynqmp_gqspi_read(xqspi, GQSPI_LPBK_DLY_ADJ_OFST) |
-			   GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
+	while ((baud_rate_val < GQSPI_BAUD_DIV_MAX) &&
+	       (clk_rate /
+		(GQSPI_BAUD_DIV_SHIFT << baud_rate_val)) > xqspi->speed_hz)
+		baud_rate_val++;
+	zynqmp_qspi_set_tapdelay(xqspi, baud_rate_val);
 	/* Reset thresholds */
 	zynqmp_gqspi_write(xqspi, GQSPI_TX_THRESHOLD_OFST,
 			   GQSPI_TX_FIFO_THRESHOLD_RESET_VAL);
@@ -326,11 +462,11 @@
 	zynqmp_gqspi_selectslave(xqspi,
 				 GQSPI_SELECT_FLASH_CS_LOWER,
 				 GQSPI_SELECT_FLASH_BUS_LOWER);
-	/* Initialize DMA */
-	zynqmp_gqspi_write(xqspi,
-			   GQSPI_QSPIDMA_DST_CTRL_OFST,
-			   GQSPI_QSPIDMA_DST_CTRL_RESET_VAL);
-
+	if (!xqspi->io_mode)
+		/* Initialize DMA */
+		zynqmp_gqspi_write(xqspi,
+				   GQSPI_QSPIDMA_DST_CTRL_OFST,
+				   GQSPI_QSPIDMA_DST_CTRL_RESET_VAL);
 	/* Enable the GQSPI */
 	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, GQSPI_EN_MASK);
 }
@@ -361,11 +497,22 @@
 	u32 genfifoentry = 0, statusreg;
 
 	genfifoentry |= GQSPI_GENFIFO_MODE_SPI;
+	if (qspi->master->flags & SPI_MASTER_BOTH_CS) {
+		zynqmp_gqspi_selectslave(xqspi,
+					 GQSPI_SELECT_FLASH_CS_BOTH,
+					 GQSPI_SELECT_FLASH_BUS_BOTH);
+	} else if (qspi->master->flags & SPI_MASTER_U_PAGE) {
+		zynqmp_gqspi_selectslave(xqspi,
+					 GQSPI_SELECT_FLASH_CS_UPPER,
+					 GQSPI_SELECT_FLASH_BUS_LOWER);
+	} else {
+		zynqmp_gqspi_selectslave(xqspi,
+					 GQSPI_SELECT_FLASH_CS_LOWER,
+					 GQSPI_SELECT_FLASH_BUS_LOWER);
+	}
 
+	genfifoentry |= xqspi->genfifobus;
 	if (!is_high) {
-		xqspi->genfifobus = GQSPI_GENFIFO_BUS_LOWER;
-		xqspi->genfifocs = GQSPI_GENFIFO_CS_LOWER;
-		genfifoentry |= xqspi->genfifobus;
 		genfifoentry |= xqspi->genfifocs;
 		genfifoentry |= GQSPI_GENFIFO_CS_SETUP;
 	} else {
@@ -385,8 +532,7 @@
 	do {
 		statusreg = zynqmp_gqspi_read(xqspi, GQSPI_ISR_OFST);
 
-		if ((statusreg & GQSPI_ISR_GENFIFOEMPTY_MASK) &&
-		    (statusreg & GQSPI_ISR_TXEMPTY_MASK))
+		if (statusreg & GQSPI_ISR_GENFIFOEMPTY_MASK)
 			break;
 		cpu_relax();
 	} while (!time_after_eq(jiffies, timeout));
@@ -448,30 +594,38 @@
 				 struct spi_device *qspi)
 {
 	ulong clk_rate;
-	u32 config_reg, baud_rate_val = 0;
+	u32 config_reg, req_hz, baud_rate_val = 0;
 
-	/* Set the clock frequency */
-	/* If req_hz == 0, default to lowest speed */
-	clk_rate = clk_get_rate(xqspi->refclk);
+	req_hz = qspi->max_speed_hz;
 
-	while ((baud_rate_val < GQSPI_BAUD_DIV_MAX) &&
-	       (clk_rate /
-		(GQSPI_BAUD_DIV_SHIFT << baud_rate_val)) > qspi->max_speed_hz)
-		baud_rate_val++;
+	if (xqspi->speed_hz != req_hz) {
+		/* Set the clock frequency */
+		/* If req_hz == 0, default to lowest speed */
+		clk_rate = clk_get_rate(xqspi->refclk);
+
+		while ((baud_rate_val < GQSPI_BAUD_DIV_MAX) &&
+		       (clk_rate /
+			(GQSPI_BAUD_DIV_SHIFT << baud_rate_val)) > req_hz)
+			baud_rate_val++;
 
-	config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
-
-	/* Set the QSPI clock phase and clock polarity */
-	config_reg &= (~GQSPI_CFG_CLK_PHA_MASK) & (~GQSPI_CFG_CLK_POL_MASK);
+		config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
 
-	if (qspi->mode & SPI_CPHA)
-		config_reg |= GQSPI_CFG_CLK_PHA_MASK;
-	if (qspi->mode & SPI_CPOL)
-		config_reg |= GQSPI_CFG_CLK_POL_MASK;
+		/* Set the QSPI clock phase and clock polarity */
+		config_reg &= (~GQSPI_CFG_CLK_PHA_MASK) &
+			(~GQSPI_CFG_CLK_POL_MASK);
+
+		if (qspi->mode & SPI_CPHA)
+			config_reg |= GQSPI_CFG_CLK_PHA_MASK;
+		if (qspi->mode & SPI_CPOL)
+			config_reg |= GQSPI_CFG_CLK_POL_MASK;
+		config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
+		config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT);
+		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+		xqspi->speed_hz = clk_rate / (GQSPI_BAUD_DIV_SHIFT <<
+				baud_rate_val);
+		zynqmp_qspi_set_tapdelay(xqspi, baud_rate_val);
+	}
 
-	config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
-	config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT);
-	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
 	return 0;
 }
 
@@ -488,10 +642,24 @@
 {
 	struct spi_controller *ctlr = qspi->master;
 	struct zynqmp_qspi *xqspi = spi_controller_get_devdata(ctlr);
+	struct device *dev = &ctlr->dev;
+	int ret;
 
 	if (ctlr->busy)
 		return -EBUSY;
 
+	ret = clk_enable(xqspi->refclk);
+	if (ret) {
+		dev_err(dev, "Cannot enable device clock.\n");
+		return ret;
+	}
+
+	ret = clk_enable(xqspi->pclk);
+	if (ret) {
+		dev_err(dev, "Cannot enable APB clock.\n");
+		clk_disable(xqspi->refclk);
+		return ret;
+	}
 	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, GQSPI_EN_MASK);
 
 	return 0;
@@ -616,6 +784,12 @@
 		if (imm_data != 0) {
 			genfifoentry &= ~GQSPI_GENFIFO_EXP;
 			genfifoentry &= ~GQSPI_GENFIFO_IMM_DATA_MASK;
+			if (imm_data % 4 != 0) {
+				if (((imm_data + 4 - (imm_data % 4)) & 0xFF) == 0x00)
+					imm_data = 0xFF;
+				else
+					imm_data = imm_data + 4 - (imm_data % 4);
+			}
 			genfifoentry |= (u8)(imm_data & 0xFF);
 			zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST,
 					   genfifoentry);
@@ -705,28 +879,34 @@
 		zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_I_STS_OFST,
 				   dma_status);
 	}
-
-	if (mask & GQSPI_ISR_TXNOT_FULL_MASK) {
-		zynqmp_qspi_filltxfifo(xqspi, GQSPI_TX_FIFO_FILL);
-		ret = IRQ_HANDLED;
-	}
-
 	if (dma_status & GQSPI_QSPIDMA_DST_I_STS_DONE_MASK) {
 		zynqmp_process_dma_irq(xqspi);
 		ret = IRQ_HANDLED;
-	} else if (!(mask & GQSPI_IER_RXEMPTY_MASK) &&
-			(mask & GQSPI_IER_GENFIFOEMPTY_MASK)) {
+	} else if ((mask & GQSPI_IER_RXNEMPTY_MASK)) {
+		zynqmp_qspi_readrxfifo(xqspi, GQSPI_RX_FIFO_FILL);
+		ret = IRQ_HANDLED;
+	}
+	if (!(mask & GQSPI_IER_RXEMPTY_MASK) &&
+	    (mask & GQSPI_IER_GENFIFOEMPTY_MASK)) {
 		zynqmp_qspi_readrxfifo(xqspi, GQSPI_RX_FIFO_FILL);
 		ret = IRQ_HANDLED;
 	}
 
 	if (xqspi->bytes_to_receive == 0 && xqspi->bytes_to_transfer == 0 &&
 	    ((status & GQSPI_IRQ_MASK) == GQSPI_IRQ_MASK)) {
-		zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_ISR_IDR_MASK);
-		complete(&xqspi->data_completion);
+		goto transfer_complete;
+	}
+	if (mask & GQSPI_ISR_TXNOT_FULL_MASK) {
+		zynqmp_qspi_filltxfifo(xqspi, GQSPI_TX_FIFO_FILL);
 		ret = IRQ_HANDLED;
 	}
+
 	return ret;
+
+transfer_complete:
+	zynqmp_disable_intr(xqspi);
+	complete(&xqspi->data_completion);
+	return IRQ_HANDLED;
 }
 
 /**
@@ -739,8 +919,9 @@
 	dma_addr_t addr;
 	u64 dma_align =  (u64)(uintptr_t)xqspi->rxbuf;
 
-	if (xqspi->bytes_to_receive < 8 ||
-	    ((dma_align & GQSPI_DMA_UNALIGN) != 0x0)) {
+	if ((xqspi->bytes_to_receive < 8 || xqspi->io_mode) ||
+	    ((dma_align & GQSPI_DMA_UNALIGN) != 0x0) ||
+	    is_vmalloc_addr(xqspi->rxbuf)) {
 		/* Setting to IO mode */
 		config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
 		config_reg &= ~GQSPI_CFG_MODE_EN_MASK;
@@ -840,8 +1021,8 @@
  */
 static int __maybe_unused zynqmp_qspi_suspend(struct device *dev)
 {
-	struct zynqmp_qspi *xqspi = dev_get_drvdata(dev);
-	struct spi_controller *ctlr = xqspi->ctlr;
+	struct spi_controller *ctlr = dev_get_drvdata(dev);
+	struct zynqmp_qspi *xqspi = spi_controller_get_devdata(ctlr);
 	int ret;
 
 	ret = spi_controller_suspend(ctlr);
@@ -864,13 +1045,28 @@
  */
 static int __maybe_unused zynqmp_qspi_resume(struct device *dev)
 {
-	struct zynqmp_qspi *xqspi = dev_get_drvdata(dev);
-	struct spi_controller *ctlr = xqspi->ctlr;
+	struct spi_controller *ctlr = dev_get_drvdata(dev);
+	struct zynqmp_qspi *xqspi = spi_controller_get_devdata(ctlr);
+	int ret = 0;
 
-	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, GQSPI_EN_MASK);
+	ret = clk_enable(xqspi->pclk);
+	if (ret) {
+		dev_err(dev, "Cannot enable APB clock.\n");
+		return ret;
+	}
 
+	ret = clk_enable(xqspi->refclk);
+	if (ret) {
+		dev_err(dev, "Cannot enable device clock.\n");
+		clk_disable(xqspi->pclk);
+		return ret;
+	}
+
+	zynqmp_qspi_init_hw(xqspi);
 	spi_controller_resume(ctlr);
 
+	clk_disable(xqspi->refclk);
+	clk_disable(xqspi->pclk);
 	return 0;
 }
 
@@ -884,10 +1080,11 @@
  */
 static int __maybe_unused zynqmp_runtime_suspend(struct device *dev)
 {
-	struct zynqmp_qspi *xqspi = dev_get_drvdata(dev);
+	struct spi_controller *ctlr = dev_get_drvdata(dev);
+	struct zynqmp_qspi *xqspi = spi_controller_get_devdata(ctlr);
 
-	clk_disable_unprepare(xqspi->refclk);
-	clk_disable_unprepare(xqspi->pclk);
+	clk_disable(xqspi->refclk);
+	clk_disable(xqspi->pclk);
 
 	return 0;
 }
@@ -902,19 +1099,20 @@
  */
 static int __maybe_unused zynqmp_runtime_resume(struct device *dev)
 {
-	struct zynqmp_qspi *xqspi = dev_get_drvdata(dev);
+	struct spi_controller *ctlr = dev_get_drvdata(dev);
+	struct zynqmp_qspi *xqspi = spi_controller_get_devdata(ctlr);
 	int ret;
 
-	ret = clk_prepare_enable(xqspi->pclk);
+	ret = clk_enable(xqspi->pclk);
 	if (ret) {
 		dev_err(dev, "Cannot enable APB clock.\n");
 		return ret;
 	}
 
-	ret = clk_prepare_enable(xqspi->refclk);
+	ret = clk_enable(xqspi->refclk);
 	if (ret) {
 		dev_err(dev, "Cannot enable device clock.\n");
-		clk_disable_unprepare(xqspi->pclk);
+		clk_disable(xqspi->pclk);
 		return ret;
 	}
 
@@ -941,6 +1139,7 @@
 	u32 genfifoentry = 0;
 	u16 opcode = op->cmd.opcode;
 	u64 opaddr;
+	u8 addrbuswidth = zynqmp_get_addr_buswidth(op);
 
 	dev_dbg(xqspi->dev, "cmd:%#x mode:%d.%d.%d.%d\n",
 		op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
@@ -958,11 +1157,14 @@
 		xqspi->rxbuf = NULL;
 		xqspi->bytes_to_transfer = op->cmd.nbytes;
 		xqspi->bytes_to_receive = 0;
-		zynqmp_qspi_write_op(xqspi, op->cmd.buswidth, genfifoentry);
+		/* Opcode always gets transmitted on single line */
+		zynqmp_qspi_write_op(xqspi, GQSPI_TX_BUS_WIDTH_SINGLE,
+				     genfifoentry);
 		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
 				   zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST) |
 				   GQSPI_CFG_START_GEN_FIFO_MASK);
 		zynqmp_gqspi_write(xqspi, GQSPI_IER_OFST,
+				   GQSPI_IER_TXEMPTY_MASK |
 				   GQSPI_IER_GENFIFOEMPTY_MASK |
 				   GQSPI_IER_TXNOT_FULL_MASK);
 		if (!wait_for_completion_timeout
@@ -983,7 +1185,7 @@
 		xqspi->rxbuf = NULL;
 		xqspi->bytes_to_transfer = op->addr.nbytes;
 		xqspi->bytes_to_receive = 0;
-		zynqmp_qspi_write_op(xqspi, op->addr.buswidth, genfifoentry);
+		zynqmp_qspi_write_op(xqspi, addrbuswidth, genfifoentry);
 		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
 				   zynqmp_gqspi_read(xqspi,
 						     GQSPI_CONFIG_OFST) |
@@ -1020,6 +1222,10 @@
 	}
 
 	if (op->data.nbytes) {
+		if (mem->spi->master->flags & SPI_MASTER_DATA_STRIPE) {
+			if (update_stripe(op))
+				genfifoentry |= GQSPI_GENFIFO_STRIPE;
+		}
 		reinit_completion(&xqspi->data_completion);
 		if (op->data.dir == SPI_MEM_DATA_OUT) {
 			xqspi->txbuf = (u8 *)op->data.buf.out;
@@ -1062,7 +1268,7 @@
 			}
 		}
 		if (!wait_for_completion_timeout
-		    (&xqspi->data_completion, msecs_to_jiffies(1000)))
+		    (&xqspi->data_completion, msecs_to_jiffies(1000000)))
 			err = -ETIMEDOUT;
 	}
 
@@ -1074,12 +1280,35 @@
 	return err;
 }
 
+static int __maybe_unused zynqmp_runtime_idle(struct device *dev)
+{
+	struct spi_controller *ctlr = dev_get_drvdata(dev);
+	struct zynqmp_qspi *xqspi = spi_controller_get_devdata(ctlr);
+	u32 value;
+
+	value = zynqmp_gqspi_read(xqspi, GQSPI_EN_OFST);
+	if (value)
+		return -EBUSY;
+
+	return 0;
+}
+
 static const struct dev_pm_ops zynqmp_qspi_dev_pm_ops = {
 	SET_RUNTIME_PM_OPS(zynqmp_runtime_suspend,
-			   zynqmp_runtime_resume, NULL)
+			   zynqmp_runtime_resume, zynqmp_runtime_idle)
 	SET_SYSTEM_SLEEP_PM_OPS(zynqmp_qspi_suspend, zynqmp_qspi_resume)
 };
 
+static const struct qspi_platform_data versal_qspi_def = {
+	.quirks = QSPI_QUIRK_HAS_TAPDELAY,
+};
+
+static const struct of_device_id zynqmp_qspi_of_match[] = {
+	{ .compatible = "xlnx,zynqmp-qspi-1.0"},
+	{ .compatible = "xlnx,versal-qspi-1.0", .data = &versal_qspi_def },
+	{ /* End of table */ }
+};
+
 static const struct spi_controller_mem_ops zynqmp_qspi_mem_ops = {
 	.exec_op = zynqmp_qspi_exec_op,
 };
@@ -1098,6 +1327,11 @@
 	struct spi_controller *ctlr;
 	struct zynqmp_qspi *xqspi;
 	struct device *dev = &pdev->dev;
+	struct device_node *nc;
+	const struct of_device_id *match;
+	u32 num_cs;
+	u32 rx_bus_width;
+	u32 tx_bus_width;
 	struct device_node *np = dev->of_node;
 
 	ctlr = spi_alloc_master(&pdev->dev, sizeof(*xqspi));
@@ -1107,8 +1341,15 @@
 	xqspi = spi_controller_get_devdata(ctlr);
 	xqspi->dev = dev;
 	xqspi->ctlr = ctlr;
-	platform_set_drvdata(pdev, xqspi);
+	platform_set_drvdata(pdev, ctlr);
+
+	match = of_match_node(zynqmp_qspi_of_match, pdev->dev.of_node);
+	if (match) {
+		const struct qspi_platform_data *p_data = match->data;
 
+		if (p_data && (p_data->quirks & QSPI_QUIRK_HAS_TAPDELAY))
+			xqspi->has_tapdelay = true;
+	}
 	xqspi->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(xqspi->regs)) {
 		ret = PTR_ERR(xqspi->regs);
@@ -1150,6 +1391,12 @@
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
+	if (of_property_read_bool(pdev->dev.of_node, "has-io-mode"))
+		xqspi->io_mode = true;
+
+	ctlr->max_speed_hz = clk_get_rate(xqspi->refclk) / 2;
+	xqspi->speed_hz = ctlr->max_speed_hz;
+
 	ret = pm_runtime_get_sync(&pdev->dev);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "Failed to pm_runtime_get_sync: %d\n", ret);
@@ -1162,6 +1409,7 @@
 	xqspi->irq = platform_get_irq(pdev, 0);
 	if (xqspi->irq <= 0) {
 		ret = -ENXIO;
+		dev_err(dev, "irq resource not found\n");
 		goto clk_dis_all;
 	}
 	ret = devm_request_irq(&pdev->dev, xqspi->irq, zynqmp_qspi_irq,
@@ -1172,12 +1420,43 @@
 		goto clk_dis_all;
 	}
 
-	dma_set_mask(&pdev->dev, DMA_BIT_MASK(44));
+	xqspi->rx_bus_width = GQSPI_RX_BUS_WIDTH_SINGLE;
+	for_each_available_child_of_node(pdev->dev.of_node, nc) {
+		ret = of_property_read_u32(nc, "spi-rx-bus-width",
+					   &rx_bus_width);
+		if (!ret) {
+			xqspi->rx_bus_width = rx_bus_width;
+			break;
+		}
+	}
+	if (ret)
+		dev_err(dev, "rx bus width not found\n");
+
+	xqspi->tx_bus_width = GQSPI_TX_BUS_WIDTH_SINGLE;
+	for_each_available_child_of_node(pdev->dev.of_node, nc) {
+		ret = of_property_read_u32(nc, "spi-tx-bus-width",
+					   &tx_bus_width);
+		if (!ret) {
+			xqspi->tx_bus_width = tx_bus_width;
+			break;
+		}
+	}
+	if (ret)
+		dev_err(dev, "tx bus width not found\n");
+
+	ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
+	if (ret < 0)
+		ctlr->num_chipselect = GQSPI_DEFAULT_NUM_CS;
+	else
+		ctlr->num_chipselect = num_cs;
+
+	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(44));
+	if (ret)
+		goto clk_dis_all;
+
 	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
-	ctlr->num_chipselect = GQSPI_DEFAULT_NUM_CS;
 	ctlr->mem_ops = &zynqmp_qspi_mem_ops;
 	ctlr->setup = zynqmp_qspi_setup_op;
-	ctlr->max_speed_hz = clk_get_rate(xqspi->refclk) / 2;
 	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
 	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
 			    SPI_TX_DUAL | SPI_TX_QUAD;
@@ -1196,9 +1475,10 @@
 	return 0;
 
 clk_dis_all:
-	pm_runtime_put_sync(&pdev->dev);
-	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
 	clk_disable_unprepare(xqspi->refclk);
 clk_dis_pclk:
 	clk_disable_unprepare(xqspi->pclk);
@@ -1218,29 +1498,27 @@
  *
  * Return:	0 Always
  */
-static int zynqmp_qspi_remove(struct platform_device *pdev)
+static void zynqmp_qspi_remove(struct platform_device *pdev)
 {
 	struct zynqmp_qspi *xqspi = platform_get_drvdata(pdev);
 
+	pm_runtime_get_sync(&pdev->dev);
+
 	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, 0x0);
+
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
 	clk_disable_unprepare(xqspi->refclk);
 	clk_disable_unprepare(xqspi->pclk);
-	pm_runtime_set_suspended(&pdev->dev);
-	pm_runtime_disable(&pdev->dev);
-
-	return 0;
 }
 
-static const struct of_device_id zynqmp_qspi_of_match[] = {
-	{ .compatible = "xlnx,zynqmp-qspi-1.0", },
-	{ /* End of table */ }
-};
-
 MODULE_DEVICE_TABLE(of, zynqmp_qspi_of_match);
 
 static struct platform_driver zynqmp_qspi_driver = {
 	.probe = zynqmp_qspi_probe,
-	.remove = zynqmp_qspi_remove,
+	.remove_new = zynqmp_qspi_remove,
 	.driver = {
 		.name = "zynqmp-qspi",
 		.of_match_table = zynqmp_qspi_of_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spi.c
@@ -335,6 +335,18 @@
 }
 EXPORT_SYMBOL_GPL(spi_get_device_id);
 
+const void *spi_get_device_match_data(const struct spi_device *sdev)
+{
+	const void *match;
+
+	match = device_get_match_data(&sdev->dev);
+	if (match)
+		return match;
+
+	return (const void *)spi_get_device_id(sdev)->driver_data;
+}
+EXPORT_SYMBOL_GPL(spi_get_device_match_data);
+
 static int spi_match_device(struct device *dev, struct device_driver *drv)
 {
 	const struct spi_device	*spi = to_spi_device(dev);
@@ -388,6 +400,16 @@
 			spi->irq = 0;
 	}
 
+	if (has_acpi_companion(dev) && spi->irq < 0) {
+		struct acpi_device *adev = to_acpi_device_node(dev->fwnode);
+
+		spi->irq = acpi_dev_gpio_irq_get(adev, 0);
+		if (spi->irq == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		if (spi->irq < 0)
+			spi->irq = 0;
+	}
+
 	ret = dev_pm_domain_attach(dev, true);
 	if (ret)
 		return ret;
@@ -451,6 +473,47 @@
 {
 	sdrv->driver.owner = owner;
 	sdrv->driver.bus = &spi_bus_type;
+
+	/*
+	 * For Really Good Reasons we use spi: modaliases not of:
+	 * modaliases for DT so module autoloading won't work if we
+	 * don't have a spi_device_id as well as a compatible string.
+	 */
+	if (sdrv->driver.of_match_table) {
+		const struct of_device_id *of_id;
+
+		for (of_id = sdrv->driver.of_match_table; of_id->compatible[0];
+		     of_id++) {
+			const char *of_name;
+
+			/* Strip off any vendor prefix */
+			of_name = strnchr(of_id->compatible,
+					  sizeof(of_id->compatible), ',');
+			if (of_name)
+				of_name++;
+			else
+				of_name = of_id->compatible;
+
+			if (sdrv->id_table) {
+				const struct spi_device_id *spi_id;
+
+				for (spi_id = sdrv->id_table; spi_id->name[0];
+				     spi_id++)
+					if (strcmp(spi_id->name, of_name) == 0)
+						break;
+
+				if (spi_id->name[0])
+					continue;
+			} else {
+				if (strcmp(sdrv->driver.name, of_name) == 0)
+					continue;
+			}
+
+			pr_warn("SPI driver %s has no spi_device_id for %s\n",
+				sdrv->driver.name, of_id->compatible);
+		}
+	}
+
 	return driver_register(&sdrv->driver);
 }
 EXPORT_SYMBOL_GPL(__spi_register_driver);
@@ -827,12 +890,9 @@
 	spi->controller->last_cs_enable = enable;
 	spi->controller->last_cs_mode_high = spi->mode & SPI_CS_HIGH;
 
-	if (spi->cs_gpiod || gpio_is_valid(spi->cs_gpio) ||
-	    !spi->controller->set_cs_timing) {
-		if (activate)
-			spi_delay_exec(&spi->cs_setup, NULL);
-		else
-			spi_delay_exec(&spi->cs_hold, NULL);
+	if ((spi->cs_gpiod || gpio_is_valid(spi->cs_gpio) ||
+	    !spi->controller->set_cs_timing) && !activate) {
+		spi_delay_exec(&spi->cs_hold, NULL);
 	}
 
 	if (spi->mode & SPI_CS_HIGH)
@@ -874,7 +934,9 @@
 
 	if (spi->cs_gpiod || gpio_is_valid(spi->cs_gpio) ||
 	    !spi->controller->set_cs_timing) {
-		if (!activate)
+		if (activate)
+			spi_delay_exec(&spi->cs_setup, NULL);
+		else
 			spi_delay_exec(&spi->cs_inactive, NULL);
 	}
 }
@@ -902,10 +964,10 @@
 	int i, ret;
 
 	if (vmalloced_buf || kmap_buf) {
-		desc_len = min_t(int, max_seg_size, PAGE_SIZE);
+		desc_len = min_t(unsigned long, max_seg_size, PAGE_SIZE);
 		sgs = DIV_ROUND_UP(len + offset_in_page(buf), desc_len);
 	} else if (virt_addr_valid(buf)) {
-		desc_len = min_t(int, max_seg_size, ctlr->max_dma_len);
+		desc_len = min_t(size_t, max_seg_size, ctlr->max_dma_len);
 		sgs = DIV_ROUND_UP(len, desc_len);
 	} else {
 		return -EINVAL;
@@ -967,6 +1029,8 @@
 	if (sgt->orig_nents) {
 		dma_unmap_sg(dev, sgt->sgl, sgt->orig_nents, dir);
 		sg_free_table(sgt);
+		sgt->orig_nents = 0;
+		sgt->nents = 0;
 	}
 }
 
@@ -993,6 +1057,7 @@
 	else
 		rx_dev = ctlr->dev.parent;
 
+	ret = -ENOMSG;
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 		if (!ctlr->can_dma(ctlr, msg->spi, xfer))
 			continue;
@@ -1016,6 +1081,9 @@
 			}
 		}
 	}
+	/* No transfer has been mapped, bail out with success */
+	if (ret)
+		return 0;
 
 	ctlr->cur_msg_mapped = true;
 
@@ -1032,11 +1100,15 @@
 
 	if (ctlr->dma_tx)
 		tx_dev = ctlr->dma_tx->device->dev;
+	else if (ctlr->dma_map_dev)
+		tx_dev = ctlr->dma_map_dev;
 	else
 		tx_dev = ctlr->dev.parent;
 
 	if (ctlr->dma_rx)
 		rx_dev = ctlr->dma_rx->device->dev;
+	else if (ctlr->dma_map_dev)
+		rx_dev = ctlr->dma_map_dev;
 	else
 		rx_dev = ctlr->dev.parent;
 
@@ -2064,6 +2136,9 @@
 	if (!of_property_read_u32(nc, "spi-max-frequency", &value))
 		spi->max_speed_hz = value;
 
+	/* Multi die flash */
+	if (of_property_read_bool(nc, "multi-die"))
+		spi->multi_die = true;
 	return 0;
 }
 
@@ -2201,8 +2276,50 @@
 	int			irq;
 	u8			bits_per_word;
 	u8			chip_select;
+	int			n;
+	int			index;
 };
 
+static int acpi_spi_count(struct acpi_resource *ares, void *data)
+{
+	struct acpi_resource_spi_serialbus *sb;
+	int *count = data;
+
+	if (ares->type != ACPI_RESOURCE_TYPE_SERIAL_BUS)
+		return 1;
+
+	sb = &ares->data.spi_serial_bus;
+	if (sb->type != ACPI_RESOURCE_SERIAL_TYPE_SPI)
+		return 1;
+
+	*count = *count + 1;
+
+	return 1;
+}
+
+/**
+ * acpi_spi_count_resources - Count the number of SpiSerialBus resources
+ * @adev:	ACPI device
+ *
+ * Returns the number of SpiSerialBus resources in the ACPI-device's
+ * resource-list; or a negative error code.
+ */
+int acpi_spi_count_resources(struct acpi_device *adev)
+{
+	LIST_HEAD(r);
+	int count = 0;
+	int ret;
+
+	ret = acpi_dev_get_resources(adev, &r, acpi_spi_count, &count);
+	if (ret < 0)
+		return ret;
+
+	acpi_dev_free_resource_list(&r);
+
+	return count;
+}
+EXPORT_SYMBOL_GPL(acpi_spi_count_resources);
+
 static void acpi_spi_parse_apple_properties(struct acpi_device *dev,
 					    struct acpi_spi_lookup *lookup)
 {
@@ -2232,6 +2349,8 @@
 		lookup->mode |= SPI_CPHA;
 }
 
+static struct spi_controller *acpi_spi_find_controller_by_adev(struct acpi_device *adev);
+
 static int acpi_spi_add_resource(struct acpi_resource *ares, void *data)
 {
 	struct acpi_spi_lookup *lookup = data;
@@ -2245,14 +2364,35 @@
 		sb = &ares->data.spi_serial_bus;
 		if (sb->type == ACPI_RESOURCE_SERIAL_TYPE_SPI) {
 
+			if (lookup->index != -1 && lookup->n++ != lookup->index)
+				return 1;
+
+			if (lookup->index == -1 && !ctlr)
+				return -ENODEV;
+
 			status = acpi_get_handle(NULL,
 						 sb->resource_source.string_ptr,
 						 &parent_handle);
 
-			if (ACPI_FAILURE(status) ||
-			    ACPI_HANDLE(ctlr->dev.parent) != parent_handle)
+			if (ACPI_FAILURE(status))
 				return -ENODEV;
 
+			if (ctlr) {
+				if (ACPI_HANDLE(ctlr->dev.parent) != parent_handle)
+					return -ENODEV;
+			} else {
+				struct acpi_device *adev;
+
+				if (acpi_bus_get_device(parent_handle, &adev))
+					return -ENODEV;
+
+				ctlr = acpi_spi_find_controller_by_adev(adev);
+				if (!ctlr)
+					return -ENODEV;
+
+				lookup->ctlr = ctlr;
+			}
+
 			/*
 			 * ACPI DeviceSelection numbering is handled by the
 			 * host controller driver in Windows and can vary
@@ -2291,8 +2431,25 @@
 	return 1;
 }
 
-static acpi_status acpi_register_spi_device(struct spi_controller *ctlr,
-					    struct acpi_device *adev)
+/**
+ * acpi_spi_device_alloc - Allocate a spi device, and fill it in with ACPI information
+ * @ctlr: controller to which the spi device belongs
+ * @adev: ACPI Device for the spi device
+ * @index: Index of the spi resource inside the ACPI Node
+ *
+ * This should be used to allocate a new spi device from and ACPI Node.
+ * The caller is responsible for calling spi_add_device to register the spi device.
+ *
+ * If ctlr is set to NULL, the Controller for the spi device will be looked up
+ * using the resource.
+ * If index is set to -1, index is not used.
+ * Note: If index is -1, ctlr must be set.
+ *
+ * Return: a pointer to the new device, or ERR_PTR on error.
+ */
+struct spi_device *acpi_spi_device_alloc(struct spi_controller *ctlr,
+					 struct acpi_device *adev,
+					 int index)
 {
 	acpi_handle parent_handle = NULL;
 	struct list_head resource_list;
@@ -2300,12 +2457,13 @@
 	struct spi_device *spi;
 	int ret;
 
-	if (acpi_bus_get_status(adev) || !adev->status.present ||
-	    acpi_device_enumerated(adev))
-		return AE_OK;
+	if (!ctlr && index == -1)
+		return ERR_PTR(-EINVAL);
 
 	lookup.ctlr		= ctlr;
 	lookup.irq		= -1;
+	lookup.index		= index;
+	lookup.n		= 0;
 
 	INIT_LIST_HEAD(&resource_list);
 	ret = acpi_dev_get_resources(adev, &resource_list,
@@ -2314,26 +2472,25 @@
 
 	if (ret < 0)
 		/* found SPI in _CRS but it points to another controller */
-		return AE_OK;
+		return ERR_PTR(-ENODEV);
 
 	if (!lookup.max_speed_hz &&
 	    ACPI_SUCCESS(acpi_get_parent(adev->handle, &parent_handle)) &&
-	    ACPI_HANDLE(ctlr->dev.parent) == parent_handle) {
+	    ACPI_HANDLE(lookup.ctlr->dev.parent) == parent_handle) {
 		/* Apple does not use _CRS but nested devices for SPI slaves */
 		acpi_spi_parse_apple_properties(adev, &lookup);
 	}
 
 	if (!lookup.max_speed_hz)
-		return AE_OK;
+		return ERR_PTR(-ENODEV);
 
-	spi = spi_alloc_device(ctlr);
+	spi = spi_alloc_device(lookup.ctlr);
 	if (!spi) {
-		dev_err(&ctlr->dev, "failed to allocate SPI device for %s\n",
+		dev_err(&lookup.ctlr->dev, "failed to allocate SPI device for %s\n",
 			dev_name(&adev->dev));
-		return AE_NO_MEMORY;
+		return ERR_PTR(-ENOMEM);
 	}
 
-
 	ACPI_COMPANION_SET(&spi->dev, adev);
 	spi->max_speed_hz	= lookup.max_speed_hz;
 	spi->mode		|= lookup.mode;
@@ -2341,12 +2498,30 @@
 	spi->bits_per_word	= lookup.bits_per_word;
 	spi->chip_select	= lookup.chip_select;
 
+	return spi;
+}
+EXPORT_SYMBOL_GPL(acpi_spi_device_alloc);
+
+static acpi_status acpi_register_spi_device(struct spi_controller *ctlr,
+					    struct acpi_device *adev)
+{
+	struct spi_device *spi;
+
+	if (acpi_bus_get_status(adev) || !adev->status.present ||
+	    acpi_device_enumerated(adev))
+		return AE_OK;
+
+	spi = acpi_spi_device_alloc(ctlr, adev, -1);
+	if (IS_ERR(spi)) {
+		if (PTR_ERR(spi) == -ENOMEM)
+			return AE_NO_MEMORY;
+		else
+			return AE_OK;
+	}
+
 	acpi_set_modalias(adev, acpi_device_hid(adev), spi->modalias,
 			  sizeof(spi->modalias));
 
-	if (spi->irq < 0)
-		spi->irq = acpi_dev_gpio_irq_get(adev, 0);
-
 	acpi_device_set_enumerated(adev);
 
 	adev->power.flags.ignore_parent = true;
@@ -2905,9 +3080,9 @@
 }
 EXPORT_SYMBOL_GPL(spi_register_controller);
 
-static void devm_spi_unregister(void *ctlr)
+static void devm_spi_unregister(struct device *dev, void *res)
 {
-	spi_unregister_controller(ctlr);
+	spi_unregister_controller(*(struct spi_controller **)res);
 }
 
 /**
@@ -2926,13 +3101,22 @@
 int devm_spi_register_controller(struct device *dev,
 				 struct spi_controller *ctlr)
 {
+	struct spi_controller **ptr;
 	int ret;
 
+	ptr = devres_alloc(devm_spi_unregister, sizeof(*ptr), GFP_KERNEL);
+	if (!ptr)
+		return -ENOMEM;
+
 	ret = spi_register_controller(ctlr);
-	if (ret)
-		return ret;
+	if (!ret) {
+		*ptr = ctlr;
+		devres_add(dev, ptr);
+	} else {
+		devres_free(ptr);
+	}
 
-	return devm_add_action_or_reset(dev, devm_spi_unregister, ctlr);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(devm_spi_register_controller);
 
@@ -2979,12 +3163,6 @@
 
 	device_del(&ctlr->dev);
 
-	/* Release the last reference on the controller if its driver
-	 * has not yet been converted to devm_spi_alloc_master/slave().
-	 */
-	if (!ctlr->devm_allocated)
-		put_device(&ctlr->dev);
-
 	/* free bus id */
 	mutex_lock(&board_lock);
 	if (found == ctlr)
@@ -2993,6 +3171,12 @@
 
 	if (IS_ENABLED(CONFIG_SPI_DYNAMIC))
 		mutex_unlock(&ctlr->add_lock);
+
+	/* Release the last reference on the controller if its driver
+	 * has not yet been converted to devm_spi_alloc_master/slave().
+	 */
+	if (!ctlr->devm_allocated)
+		put_device(&ctlr->dev);
 }
 EXPORT_SYMBOL_GPL(spi_unregister_controller);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spi/spidev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spi/spidev.c
@@ -8,19 +8,18 @@
  */
 
 #include <linux/init.h>
-#include <linux/module.h>
 #include <linux/ioctl.h>
 #include <linux/fs.h>
 #include <linux/device.h>
 #include <linux/err.h>
 #include <linux/list.h>
 #include <linux/errno.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
 #include <linux/mutex.h>
+#include <linux/property.h>
 #include <linux/slab.h>
 #include <linux/compat.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/acpi.h>
 
 #include <linux/spi/spi.h>
 #include <linux/spi/spidev.h>
@@ -376,12 +375,23 @@
 	switch (cmd) {
 	/* read requests */
 	case SPI_IOC_RD_MODE:
-		retval = put_user(spi->mode & SPI_MODE_MASK,
-					(__u8 __user *)arg);
-		break;
 	case SPI_IOC_RD_MODE32:
-		retval = put_user(spi->mode & SPI_MODE_MASK,
-					(__u32 __user *)arg);
+		tmp = spi->mode;
+
+		{
+			struct spi_controller *ctlr = spi->controller;
+
+			if (ctlr->use_gpio_descriptors && ctlr->cs_gpiods &&
+			    ctlr->cs_gpiods[spi->chip_select])
+				tmp &= ~SPI_CS_HIGH;
+		}
+
+		if (cmd == SPI_IOC_RD_MODE)
+			retval = put_user(tmp & SPI_MODE_MASK,
+					  (__u8 __user *)arg);
+		else
+			retval = put_user(tmp & SPI_MODE_MASK,
+					  (__u32 __user *)arg);
 		break;
 	case SPI_IOC_RD_LSB_FIRST:
 		retval = put_user((spi->mode & SPI_LSB_FIRST) ?  1 : 0,
@@ -581,7 +591,6 @@
 	if (!spidev->tx_buffer) {
 		spidev->tx_buffer = kmalloc(bufsiz, GFP_KERNEL);
 		if (!spidev->tx_buffer) {
-			dev_dbg(&spidev->spi->dev, "open/ENOMEM\n");
 			status = -ENOMEM;
 			goto err_find_dev;
 		}
@@ -590,7 +599,6 @@
 	if (!spidev->rx_buffer) {
 		spidev->rx_buffer = kmalloc(bufsiz, GFP_KERNEL);
 		if (!spidev->rx_buffer) {
-			dev_dbg(&spidev->spi->dev, "open/ENOMEM\n");
 			status = -ENOMEM;
 			goto err_alloc_rx_buf;
 		}
@@ -674,7 +682,9 @@
 static struct class *spidev_class;
 
 static const struct spi_device_id spidev_spi_ids[] = {
+	{ .name = "bh2228fv" },
 	{ .name = "dh2228fv" },
+	{ .name = "jg10309-01" },
 	{ .name = "ltc2488" },
 	{ .name = "sx1301" },
 	{ .name = "bk4" },
@@ -682,29 +692,46 @@
 	{ .name = "m53cpld" },
 	{ .name = "spi-petra" },
 	{ .name = "spi-authenta" },
+	{ .name = "em3581" },
 	{},
 };
 MODULE_DEVICE_TABLE(spi, spidev_spi_ids);
 
-#ifdef CONFIG_OF
+/*
+ * spidev should never be referenced in DT without a specific compatible string,
+ * it is a Linux implementation thing rather than a description of the hardware.
+ */
+static int spidev_of_check(struct device *dev)
+{
+	if (device_property_match_string(dev, "compatible", "spidev") < 0)
+		return 0;
+
+	dev_err(dev, "spidev listed directly in DT is not supported\n");
+	return -EINVAL;
+}
+
 static const struct of_device_id spidev_dt_ids[] = {
-	{ .compatible = "rohm,dh2228fv" },
-	{ .compatible = "lineartechnology,ltc2488" },
-	{ .compatible = "semtech,sx1301" },
-	{ .compatible = "lwn,bk4" },
-	{ .compatible = "dh,dhcom-board" },
-	{ .compatible = "menlo,m53cpld" },
-	{ .compatible = "cisco,spi-petra" },
-	{ .compatible = "micron,spi-authenta" },
+	{ .compatible = "cisco,spi-petra", .data = &spidev_of_check },
+	{ .compatible = "dh,dhcom-board", .data = &spidev_of_check },
+	{ .compatible = "elgin,jg10309-01", .data = &spidev_of_check },
+	{ .compatible = "lineartechnology,ltc2488", .data = &spidev_of_check },
+	{ .compatible = "lwn,bk4", .data = &spidev_of_check },
+	{ .compatible = "menlo,m53cpld", .data = &spidev_of_check },
+	{ .compatible = "micron,spi-authenta", .data = &spidev_of_check },
+	{ .compatible = "rohm,bh2228fv", .data = &spidev_of_check },
+	{ .compatible = "rohm,dh2228fv", .data = &spidev_of_check },
+	{ .compatible = "semtech,sx1301", .data = &spidev_of_check },
+	{ .compatible = "silabs,em3581", .data = &spidev_of_check },
 	{},
 };
 MODULE_DEVICE_TABLE(of, spidev_dt_ids);
-#endif
-
-#ifdef CONFIG_ACPI
 
 /* Dummy SPI devices not to be used in production systems */
-#define SPIDEV_ACPI_DUMMY	1
+static int spidev_acpi_check(struct device *dev)
+{
+	dev_warn(dev, "do not use this driver in production systems!\n");
+	return 0;
+}
 
 static const struct acpi_device_id spidev_acpi_ids[] = {
 	/*
@@ -713,49 +740,28 @@
 	 * description of the connected peripheral and they should also use
 	 * a proper driver instead of poking directly to the SPI bus.
 	 */
-	{ "SPT0001", SPIDEV_ACPI_DUMMY },
-	{ "SPT0002", SPIDEV_ACPI_DUMMY },
-	{ "SPT0003", SPIDEV_ACPI_DUMMY },
+	{ "SPT0001", (kernel_ulong_t)&spidev_acpi_check },
+	{ "SPT0002", (kernel_ulong_t)&spidev_acpi_check },
+	{ "SPT0003", (kernel_ulong_t)&spidev_acpi_check },
 	{},
 };
 MODULE_DEVICE_TABLE(acpi, spidev_acpi_ids);
 
-static void spidev_probe_acpi(struct spi_device *spi)
-{
-	const struct acpi_device_id *id;
-
-	if (!has_acpi_companion(&spi->dev))
-		return;
-
-	id = acpi_match_device(spidev_acpi_ids, &spi->dev);
-	if (WARN_ON(!id))
-		return;
-
-	if (id->driver_data == SPIDEV_ACPI_DUMMY)
-		dev_warn(&spi->dev, "do not use this driver in production systems!\n");
-}
-#else
-static inline void spidev_probe_acpi(struct spi_device *spi) {}
-#endif
-
 /*-------------------------------------------------------------------------*/
 
 static int spidev_probe(struct spi_device *spi)
 {
+	int (*match)(struct device *dev);
 	struct spidev_data	*spidev;
 	int			status;
 	unsigned long		minor;
 
-	/*
-	 * spidev should never be referenced in DT without a specific
-	 * compatible string, it is a Linux implementation thing
-	 * rather than a description of the hardware.
-	 */
-	WARN(spi->dev.of_node &&
-	     of_device_is_compatible(spi->dev.of_node, "spidev"),
-	     "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node);
-
-	spidev_probe_acpi(spi);
+	match = device_get_match_data(&spi->dev);
+	if (match) {
+		status = match(&spi->dev);
+		if (status)
+			return status;
+	}
 
 	/* Allocate driver data */
 	spidev = kzalloc(sizeof(*spidev), GFP_KERNEL);
@@ -826,8 +832,8 @@
 static struct spi_driver spidev_spi_driver = {
 	.driver = {
 		.name =		"spidev",
-		.of_match_table = of_match_ptr(spidev_dt_ids),
-		.acpi_match_table = ACPI_PTR(spidev_acpi_ids),
+		.of_match_table = spidev_dt_ids,
+		.acpi_match_table = spidev_acpi_ids,
 	},
 	.probe =	spidev_probe,
 	.remove =	spidev_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spmi/hisi-spmi-controller.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spmi/hisi-spmi-controller.c
@@ -303,7 +303,6 @@
 
 	spin_lock_init(&spmi_controller->lock);
 
-	ctrl->nr = spmi_controller->channel;
 	ctrl->dev.parent = pdev->dev.parent;
 	ctrl->dev.of_node = of_node_get(pdev->dev.of_node);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spmi/spmi-pmic-arb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spmi/spmi-pmic-arb.c
@@ -887,7 +887,8 @@
 	 * version 5, there is more than one APID mapped to each PPID.
 	 * The owner field for each of these mappings specifies the EE which is
 	 * allowed to write to the APID.  The owner of the last (highest) APID
-	 * for a given PPID will receive interrupts from the PPID.
+	 * which has the IRQ owner bit set for a given PPID will receive
+	 * interrupts from the PPID.
 	 */
 	for (i = 0; ; i++, apidd++) {
 		offset = pmic_arb->ver_ops->apid_map_offset(i);
@@ -910,16 +911,16 @@
 		apid = pmic_arb->ppid_to_apid[ppid] & ~PMIC_ARB_APID_VALID;
 		prev_apidd = &pmic_arb->apid_data[apid];
 
-		if (valid && is_irq_ee &&
-				prev_apidd->write_ee == pmic_arb->ee) {
+		if (!valid || apidd->write_ee == pmic_arb->ee) {
+			/* First PPID mapping or one for this EE */
+			pmic_arb->ppid_to_apid[ppid] = i | PMIC_ARB_APID_VALID;
+		} else if (valid && is_irq_ee &&
+			   prev_apidd->write_ee == pmic_arb->ee) {
 			/*
 			 * Duplicate PPID mapping after the one for this EE;
 			 * override the irq owner
 			 */
 			prev_apidd->irq_ee = apidd->irq_ee;
-		} else if (!valid || is_irq_ee) {
-			/* First PPID mapping or duplicate for another EE */
-			pmic_arb->ppid_to_apid[ppid] = i | PMIC_ARB_APID_VALID;
 		}
 
 		apidd->ppid = ppid;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/spmi/spmi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/spmi/spmi.c
@@ -350,7 +350,8 @@
 	const struct spmi_driver *sdrv = to_spmi_driver(dev->driver);
 
 	pm_runtime_get_sync(dev);
-	sdrv->remove(to_spmi_device(dev));
+	if (sdrv->remove)
+		sdrv->remove(to_spmi_device(dev));
 	pm_runtime_put_noidle(dev);
 
 	pm_runtime_disable(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/ssb/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/ssb/main.c
@@ -341,11 +341,13 @@
 
 static int ssb_device_uevent(struct device *dev, struct kobj_uevent_env *env)
 {
-	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_device *ssb_dev;
 
 	if (!dev)
 		return -ENODEV;
 
+	ssb_dev = dev_to_ssb_dev(dev);
+
 	return add_uevent_var(env,
 			     "MODALIAS=ssb:v%04Xid%04Xrev%02X",
 			     ssb_dev->id.vendor, ssb_dev->id.coreid,
@@ -837,7 +839,7 @@
 	case SSB_CHIPCO_CLK_F6_7:
 		return 7;
 	}
-	return 0;
+	return 1;
 }
 
 /* Calculate the speed the backplane would run at a given set of clockcontrol values */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/Kconfig
@@ -72,7 +72,7 @@
 
 source "drivers/staging/unisys/Kconfig"
 
-source "drivers/staging/clocking-wizard/Kconfig"
+source "drivers/staging/apf/Kconfig"
 
 source "drivers/staging/fbtft/Kconfig"
 
@@ -102,4 +102,18 @@
 
 source "drivers/staging/wfx/Kconfig"
 
+source "drivers/staging/fclk/Kconfig"
+
+source "drivers/staging/xlnxsync/Kconfig"
+
+source "drivers/staging/xlnx_tsmux/Kconfig"
+
+source "drivers/staging/xroeframer/Kconfig"
+
+source "drivers/staging/xroetrafficgen/Kconfig"
+
+source "drivers/staging/uartlite-rs485/Kconfig"
+
+source "drivers/staging/xilinx-tsn/Kconfig"
+
 endif # STAGING
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/Makefile
@@ -26,7 +26,7 @@
 obj-$(CONFIG_FIREWIRE_SERIAL)	+= fwserial/
 obj-$(CONFIG_GS_FPGABOOT)	+= gs_fpgaboot/
 obj-$(CONFIG_UNISYSSPAR)	+= unisys/
-obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD)	+= clocking-wizard/
+obj-$(CONFIG_XILINX_APF)	+= apf/
 obj-$(CONFIG_FB_TFT)		+= fbtft/
 obj-$(CONFIG_MOST)		+= most/
 obj-$(CONFIG_KS7010)		+= ks7010/
@@ -41,3 +41,9 @@
 obj-$(CONFIG_FIELDBUS_DEV)     += fieldbus/
 obj-$(CONFIG_QLGE)		+= qlge/
 obj-$(CONFIG_WFX)		+= wfx/
+obj-$(CONFIG_XILINX_FCLK)	+= fclk/
+obj-$(CONFIG_XLNX_SYNC)		+= xlnxsync/
+obj-$(CONFIG_XLNX_TSMUX)	+= xlnx_tsmux/
+obj-$(CONFIG_XROE_FRAMER)	+= xroeframer/
+obj-$(CONFIG_SERIAL_UARTLITE_RS485)	+= uartlite-rs485/
+obj-$(CONFIG_XILINX_TSN)	+= xilinx-tsn/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/android/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/android/Kconfig
@@ -4,7 +4,7 @@
 if ANDROID
 
 config ASHMEM
-	bool "Enable the Anonymous Shared Memory Subsystem"
+	tristate "Enable the Anonymous Shared Memory Subsystem"
 	depends on SHMEM
 	help
 	  The ashmem subsystem is a new shared memory allocator, similar to
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/android/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/android/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
 ccflags-y += -I$(src)			# needed for trace events
 
-obj-$(CONFIG_ASHMEM)			+= ashmem.o
+ashmem_linux-y				+= ashmem.o
+obj-$(CONFIG_ASHMEM)			+= ashmem_linux.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/android/ashmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/android/ashmem.c
@@ -19,6 +19,7 @@
 #include <linux/security.h>
 #include <linux/mm.h>
 #include <linux/mman.h>
+#include <linux/module.h>
 #include <linux/uaccess.h>
 #include <linux/personality.h>
 #include <linux/bitops.h>
@@ -967,4 +968,18 @@
 out:
 	return ret;
 }
-device_initcall(ashmem_init);
+
+static void __exit ashmem_exit(void)
+{
+	misc_deregister(&ashmem_misc);
+	unregister_shrinker(&ashmem_shrinker);
+	kmem_cache_destroy(ashmem_range_cachep);
+	kmem_cache_destroy(ashmem_area_cachep);
+}
+
+module_init(ashmem_init);
+module_exit(ashmem_exit);
+
+MODULE_AUTHOR("Google, Inc.");
+MODULE_DESCRIPTION("Driver for Android shared memory device");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/Kconfig
@@ -0,0 +1,20 @@
+#
+# APF driver configuration
+#
+
+menuconfig XILINX_APF
+	bool "Xilinx APF Accelerator driver"
+	depends on ARCH_ZYNQ || ARCH_ZYNQMP
+	default n
+	select UIO
+	select DMA_SHARED_BUFFER
+	help
+	  Select if you want to include APF accelerator driver
+
+config XILINX_DMA_APF
+	bool "Xilinx APF DMA engines support"
+	depends on XILINX_APF
+	select DMA_ENGINE
+	select DMADEVICES
+	help
+	  Enable support for the Xilinx APF DMA controllers.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/Makefile
@@ -0,0 +1,9 @@
+# gpio support: dedicated expander chips, etc
+
+ccflags-$(CONFIG_DEBUG_XILINX_APF) += -DDEBUG
+ccflags-$(CONFIG_XILINX_APF) += -Idrivers/dma
+
+obj-$(CONFIG_XILINX_APF) += xlnk.o
+obj-$(CONFIG_XILINX_APF) += xlnk-eng.o
+obj-$(CONFIG_XILINX_DMA_APF) += xilinx-dma-apf.o
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/dt-binding.txt
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/dt-binding.txt
@@ -0,0 +1,17 @@
+* Xilinx APF xlnk driver
+
+Required properties:
+- compatible: Should be "xlnx,xlnk"
+- clock-names: List of clock names
+- clocks: List of clock sources corresponding to the clock names
+
+The number of elements on the clock-names and clocks lists should be the same.
+If there are no controllable clocks, the xlnk node should be omitted from the
+devicetree.
+
+Example:
+	xlnk {
+		compatible = "xlnx,xlnk-1.0";
+		clock-names = "clk166", "clk150", "clk100", "clk200";
+		clocks = <&clkc 15>, <&clkc 16>, <&clkc 17>, <&clkc 18>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xilinx-dma-apf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xilinx-dma-apf.c
@@ -0,0 +1,1220 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx AXI DMA Engine support
+ *
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ *
+ * Description:
+ * This driver supports Xilinx AXI DMA engine:
+ *  . Axi DMA engine, it does transfers between memory and device. It can be
+ *    configured to have one channel or two channels. If configured as two
+ *    channels, one is for transmit to device and another is for receive from
+ *    device.
+ */
+
+#include <asm/cacheflush.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/dma-map-ops.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/fs.h>
+#include <linux/gfp.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/pagemap.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+
+#include "xilinx-dma-apf.h"
+#include "xlnk.h"
+
+static DEFINE_MUTEX(dma_list_mutex);
+static LIST_HEAD(dma_device_list);
+/* IO accessors */
+#define DMA_OUT_64(addr, val)   (writeq(val, addr))
+#define DMA_OUT(addr, val)      (iowrite32(val, addr))
+#define DMA_IN(addr)            (ioread32(addr))
+
+#define GET_LOW(x) ((u32)((x) & 0xFFFFFFFF))
+#define GET_HI(x) ((u32)((x) / 0x100000000))
+
+/* Driver functions */
+static void xdma_clean_bd(struct xdma_desc_hw *bd)
+{
+	bd->src_addr = 0x0;
+	bd->control = 0x0;
+	bd->status = 0x0;
+	bd->app[0] = 0x0;
+	bd->app[1] = 0x0;
+	bd->app[2] = 0x0;
+	bd->app[3] = 0x0;
+	bd->app[4] = 0x0;
+	bd->dmahead = 0x0;
+	bd->sw_flag = 0x0;
+}
+
+static int dma_is_running(struct xdma_chan *chan)
+{
+	return !(DMA_IN(&chan->regs->sr) & XDMA_SR_HALTED_MASK) &&
+		(DMA_IN(&chan->regs->cr) & XDMA_CR_RUNSTOP_MASK);
+}
+
+static int dma_is_idle(struct xdma_chan *chan)
+{
+	return DMA_IN(&chan->regs->sr) & XDMA_SR_IDLE_MASK;
+}
+
+static void dma_halt(struct xdma_chan *chan)
+{
+	DMA_OUT(&chan->regs->cr,
+		(DMA_IN(&chan->regs->cr)  & ~XDMA_CR_RUNSTOP_MASK));
+}
+
+static void dma_start(struct xdma_chan *chan)
+{
+	DMA_OUT(&chan->regs->cr,
+		(DMA_IN(&chan->regs->cr) | XDMA_CR_RUNSTOP_MASK));
+}
+
+static int dma_init(struct xdma_chan *chan)
+{
+	int loop = XDMA_RESET_LOOP;
+
+	DMA_OUT(&chan->regs->cr,
+		(DMA_IN(&chan->regs->cr) | XDMA_CR_RESET_MASK));
+
+	/* Wait for the hardware to finish reset
+	 */
+	while (loop) {
+		if (!(DMA_IN(&chan->regs->cr) & XDMA_CR_RESET_MASK))
+			break;
+
+		loop -= 1;
+	}
+
+	if (!loop)
+		return 1;
+
+	return 0;
+}
+
+static int xdma_alloc_chan_descriptors(struct xdma_chan *chan)
+{
+	int i;
+	u8 *ptr;
+
+	/*
+	 * We need the descriptor to be aligned to 64bytes
+	 * for meeting Xilinx DMA specification requirement.
+	 */
+	ptr = (u8 *)dma_alloc_coherent(chan->dev,
+				(sizeof(struct xdma_desc_hw) * XDMA_MAX_BD_CNT),
+				&chan->bd_phys_addr,
+				GFP_KERNEL);
+
+	if (!ptr) {
+		dev_err(chan->dev,
+			"unable to allocate channel %d descriptor pool\n",
+			chan->id);
+		return -ENOMEM;
+	}
+
+	memset(ptr, 0, (sizeof(struct xdma_desc_hw) * XDMA_MAX_BD_CNT));
+	chan->bd_cur = 0;
+	chan->bd_tail = 0;
+	chan->bd_used = 0;
+	chan->bd_chain_size = sizeof(struct xdma_desc_hw) * XDMA_MAX_BD_CNT;
+
+	/*
+	 * Pre allocate all the channels.
+	 */
+	for (i = 0; i < XDMA_MAX_BD_CNT; i++) {
+		chan->bds[i] = (struct xdma_desc_hw *)
+				(ptr + (sizeof(struct xdma_desc_hw) * i));
+		chan->bds[i]->next_desc = chan->bd_phys_addr +
+					(sizeof(struct xdma_desc_hw) *
+						((i + 1) % XDMA_MAX_BD_CNT));
+	}
+
+	/* there is at least one descriptor free to be allocated */
+	return 0;
+}
+
+static void xdma_free_chan_resources(struct xdma_chan *chan)
+{
+	dev_dbg(chan->dev, "Free all channel resources.\n");
+	dma_free_coherent(chan->dev, (sizeof(struct xdma_desc_hw) *
+			XDMA_MAX_BD_CNT), chan->bds[0], chan->bd_phys_addr);
+}
+
+static void xilinx_chan_desc_reinit(struct xdma_chan *chan)
+{
+	struct xdma_desc_hw *desc;
+	unsigned int start, end;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+	start = 0;
+	end = XDMA_MAX_BD_CNT;
+
+	while (start < end) {
+		desc = chan->bds[start];
+		xdma_clean_bd(desc);
+		start++;
+	}
+	/* Re-initialize bd_cur and bd_tail values */
+	chan->bd_cur = 0;
+	chan->bd_tail = 0;
+	chan->bd_used = 0;
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+static void xilinx_chan_desc_cleanup(struct xdma_chan *chan)
+{
+	struct xdma_head *dmahead;
+	struct xdma_desc_hw *desc;
+	struct completion *cmp;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+#define XDMA_BD_STS_RXEOF_MASK 0x04000000
+	desc = chan->bds[chan->bd_cur];
+	while (desc->status & XDMA_BD_STS_ALL_MASK) {
+		if ((desc->status & XDMA_BD_STS_RXEOF_MASK) &&
+		    !(desc->dmahead)) {
+			pr_info("ERROR: premature EOF on DMA\n");
+			dma_init(chan); /* reset the dma HW */
+			while (!(desc->dmahead)) {
+				xdma_clean_bd(desc);
+				chan->bd_used--;
+				chan->bd_cur++;
+				if (chan->bd_cur >= XDMA_MAX_BD_CNT)
+					chan->bd_cur = 0;
+				desc = chan->bds[chan->bd_cur];
+			}
+		}
+		if (desc->dmahead) {
+			if ((desc->sw_flag & XDMA_BD_SF_POLL_MODE_MASK))
+				if (!(desc->sw_flag & XDMA_BD_SF_SW_DONE_MASK))
+					break;
+
+			dmahead = (struct xdma_head *)desc->dmahead;
+			cmp = (struct completion *)&dmahead->cmp;
+			if (dmahead->nappwords_o)
+				memcpy(dmahead->appwords_o, desc->app,
+				       dmahead->nappwords_o * sizeof(u32));
+
+			if (chan->poll_mode)
+				cmp->done = 1;
+			else
+				complete(cmp);
+		}
+		xdma_clean_bd(desc);
+		chan->bd_used--;
+		chan->bd_cur++;
+		if (chan->bd_cur >= XDMA_MAX_BD_CNT)
+			chan->bd_cur = 0;
+		desc = chan->bds[chan->bd_cur];
+	}
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+static void xdma_err_tasklet(unsigned long data)
+{
+	struct xdma_chan *chan = (struct xdma_chan *)data;
+
+	if (chan->err) {
+		/* If reset failed, need to hard reset
+		 * Channel is no longer functional
+		 */
+		if (!dma_init(chan))
+			chan->err = 0;
+		else
+			dev_err(chan->dev, "DMA channel reset failed, please reset system\n");
+	}
+
+	/* Barrier to assert descriptor init is reaches memory */
+	rmb();
+	xilinx_chan_desc_cleanup(chan);
+
+	xilinx_chan_desc_reinit(chan);
+}
+
+static void xdma_tasklet(unsigned long data)
+{
+	struct xdma_chan *chan = (struct xdma_chan *)data;
+
+	xilinx_chan_desc_cleanup(chan);
+}
+
+static void dump_cur_bd(struct xdma_chan *chan)
+{
+	u32 index;
+
+	index = (((u32)DMA_IN(&chan->regs->cdr)) - chan->bd_phys_addr) /
+			sizeof(struct xdma_desc_hw);
+
+	dev_err(chan->dev, "cur bd @ %08x\n",   (u32)DMA_IN(&chan->regs->cdr));
+	dev_err(chan->dev, "  buf  = %p\n",
+		(void *)chan->bds[index]->src_addr);
+	dev_err(chan->dev, "  ctrl = 0x%08x\n", chan->bds[index]->control);
+	dev_err(chan->dev, "  sts  = 0x%08x\n", chan->bds[index]->status);
+	dev_err(chan->dev, "  next = %p\n",
+		(void *)chan->bds[index]->next_desc);
+}
+
+static irqreturn_t xdma_rx_intr_handler(int irq, void *data)
+{
+	struct xdma_chan *chan = data;
+	u32 stat;
+
+	stat = DMA_IN(&chan->regs->sr);
+
+	if (!(stat & XDMA_XR_IRQ_ALL_MASK))
+		return IRQ_NONE;
+
+	/* Ack the interrupts */
+	DMA_OUT(&chan->regs->sr, (stat & XDMA_XR_IRQ_ALL_MASK));
+
+	if (stat & XDMA_XR_IRQ_ERROR_MASK) {
+		dev_err(chan->dev, "Channel %s has errors %x, cdr %x tdr %x\n",
+			chan->name, (unsigned int)stat,
+			(unsigned int)DMA_IN(&chan->regs->cdr),
+			(unsigned int)DMA_IN(&chan->regs->tdr));
+
+		dump_cur_bd(chan);
+
+		chan->err = 1;
+		tasklet_schedule(&chan->dma_err_tasklet);
+	}
+
+	if (!(chan->poll_mode) && ((stat & XDMA_XR_IRQ_DELAY_MASK) ||
+				   (stat & XDMA_XR_IRQ_IOC_MASK)))
+		tasklet_schedule(&chan->tasklet);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t xdma_tx_intr_handler(int irq, void *data)
+{
+	struct xdma_chan *chan = data;
+	u32 stat;
+
+	stat = DMA_IN(&chan->regs->sr);
+
+	if (!(stat & XDMA_XR_IRQ_ALL_MASK))
+		return IRQ_NONE;
+
+	/* Ack the interrupts */
+	DMA_OUT(&chan->regs->sr, (stat & XDMA_XR_IRQ_ALL_MASK));
+
+	if (stat & XDMA_XR_IRQ_ERROR_MASK) {
+		dev_err(chan->dev, "Channel %s has errors %x, cdr %x tdr %x\n",
+			chan->name, (unsigned int)stat,
+			(unsigned int)DMA_IN(&chan->regs->cdr),
+			(unsigned int)DMA_IN(&chan->regs->tdr));
+
+		dump_cur_bd(chan);
+
+		chan->err = 1;
+		tasklet_schedule(&chan->dma_err_tasklet);
+	}
+
+	if (!(chan->poll_mode) && ((stat & XDMA_XR_IRQ_DELAY_MASK) ||
+				   (stat & XDMA_XR_IRQ_IOC_MASK)))
+		tasklet_schedule(&chan->tasklet);
+
+	return IRQ_HANDLED;
+}
+
+static void xdma_start_transfer(struct xdma_chan *chan,
+				int start_index,
+				int end_index)
+{
+	xlnk_intptr_type cur_phys;
+	xlnk_intptr_type tail_phys;
+	u32 regval;
+
+	if (chan->err)
+		return;
+
+	cur_phys = chan->bd_phys_addr + (start_index *
+					sizeof(struct xdma_desc_hw));
+	tail_phys = chan->bd_phys_addr + (end_index *
+					sizeof(struct xdma_desc_hw));
+	/* If hardware is busy, move the tail & return */
+	if (dma_is_running(chan) || dma_is_idle(chan)) {
+#if XLNK_SYS_BIT_WIDTH == 32
+		DMA_OUT(&chan->regs->tdr, tail_phys);
+#else
+		DMA_OUT_64(&chan->regs->tdr, tail_phys);
+#endif
+		return;
+	}
+
+#if XLNK_SYS_BIT_WIDTH == 32
+	DMA_OUT(&chan->regs->cdr, cur_phys);
+#else
+	DMA_OUT_64(&chan->regs->cdr, cur_phys);
+#endif
+
+	dma_start(chan);
+
+	/* Enable interrupts */
+	regval = DMA_IN(&chan->regs->cr);
+	regval |= (chan->poll_mode ? XDMA_XR_IRQ_ERROR_MASK
+					: XDMA_XR_IRQ_ALL_MASK);
+	DMA_OUT(&chan->regs->cr, regval);
+
+	/* Update tail ptr register and start the transfer */
+#if XLNK_SYS_BIT_WIDTH == 32
+	DMA_OUT(&chan->regs->tdr, tail_phys);
+#else
+	DMA_OUT_64(&chan->regs->tdr, tail_phys);
+#endif
+}
+
+static int xdma_setup_hw_desc(struct xdma_chan *chan,
+			      struct xdma_head *dmahead,
+			      struct scatterlist *sgl,
+			      unsigned int sg_len,
+			      enum dma_data_direction direction,
+			      unsigned int nappwords_i,
+			      u32 *appwords_i)
+{
+	struct xdma_desc_hw *bd = NULL;
+	size_t copy;
+	struct scatterlist *sg;
+	size_t sg_used;
+	dma_addr_t dma_src;
+	int i, start_index = -1, end_index1 = 0, end_index2 = -1;
+	int status;
+	unsigned long flags;
+	unsigned int bd_used_saved;
+
+	if (!chan) {
+		pr_err("Requested transfer on invalid channel\n");
+		return -ENODEV;
+	}
+
+	/* if we almost run out of bd, try to recycle some */
+	if ((chan->poll_mode) && (chan->bd_used >= XDMA_BD_CLEANUP_THRESHOLD))
+		xilinx_chan_desc_cleanup(chan);
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	bd_used_saved = chan->bd_used;
+	/*
+	 * Build transactions using information in the scatter gather list
+	 */
+	for_each_sg(sgl, sg, sg_len, i) {
+		sg_used = 0;
+
+		/* Loop until the entire scatterlist entry is used */
+		while (sg_used < sg_dma_len(sg)) {
+			/* Allocate the link descriptor from DMA pool */
+			bd = chan->bds[chan->bd_tail];
+			if ((bd->control) & (XDMA_BD_STS_ACTUAL_LEN_MASK)) {
+				end_index2 = chan->bd_tail;
+				status = -ENOMEM;
+				/* If first was not set, then we failed to
+				 * allocate the very first descriptor,
+				 * and we're done
+				 */
+				if (start_index == -1)
+					goto out_unlock;
+				else
+					goto out_clean;
+			}
+			/*
+			 * Calculate the maximum number of bytes to transfer,
+			 * making sure it is less than the DMA controller limit
+			 */
+			copy = min((size_t)(sg_dma_len(sg) - sg_used),
+				   (size_t)chan->max_len);
+			/*
+			 * Only the src address for DMA
+			 */
+			dma_src = sg_dma_address(sg) + sg_used;
+			bd->src_addr = dma_src;
+
+			/* Fill in the descriptor */
+			bd->control = copy;
+
+			/*
+			 * If this is not the first descriptor, chain the
+			 * current descriptor after the previous descriptor
+			 *
+			 * For the first DMA_TO_DEVICE transfer, set SOP
+			 */
+			if (start_index == -1) {
+				start_index = chan->bd_tail;
+
+				if (nappwords_i)
+					memcpy(bd->app, appwords_i,
+					       nappwords_i * sizeof(u32));
+
+				if (direction == DMA_TO_DEVICE)
+					bd->control |= XDMA_BD_SOP;
+			}
+
+			sg_used += copy;
+			end_index2 = chan->bd_tail;
+			chan->bd_tail++;
+			chan->bd_used++;
+			if (chan->bd_tail >= XDMA_MAX_BD_CNT) {
+				end_index1 = XDMA_MAX_BD_CNT;
+				chan->bd_tail = 0;
+			}
+		}
+	}
+
+	if (start_index == -1) {
+		status = -EINVAL;
+		goto out_unlock;
+	}
+
+	bd->dmahead = (xlnk_intptr_type)dmahead;
+	bd->sw_flag = chan->poll_mode ? XDMA_BD_SF_POLL_MODE_MASK : 0;
+	dmahead->last_bd_index = end_index2;
+
+	if (direction == DMA_TO_DEVICE)
+		bd->control |= XDMA_BD_EOP;
+
+	/* Barrier to assert control word write commits */
+	wmb();
+
+	xdma_start_transfer(chan, start_index, end_index2);
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+	return 0;
+
+out_clean:
+	if (!end_index1) {
+		for (i = start_index; i < end_index2; i++)
+			xdma_clean_bd(chan->bds[i]);
+	} else {
+		/* clean till the end of bd list first, and then 2nd end */
+		for (i = start_index; i < end_index1; i++)
+			xdma_clean_bd(chan->bds[i]);
+
+		end_index1 = 0;
+		for (i = end_index1; i < end_index2; i++)
+			xdma_clean_bd(chan->bds[i]);
+	}
+	/* Move the bd_tail back */
+	chan->bd_tail = start_index;
+	chan->bd_used = bd_used_saved;
+
+out_unlock:
+	spin_unlock_irqrestore(&chan->lock, flags);
+
+	return status;
+}
+
+/*
+ *  create minimal length scatter gather list for physically contiguous buffer
+ *  that starts at phy_buf and has length phy_buf_len bytes
+ */
+static unsigned int phy_buf_to_sgl(xlnk_intptr_type phy_buf,
+				   unsigned int phy_buf_len,
+				   struct scatterlist *sgl)
+{
+	unsigned int sgl_cnt = 0;
+	struct scatterlist *sgl_head;
+	unsigned int dma_len;
+	unsigned int num_bd;
+
+	if (!phy_buf || !phy_buf_len) {
+		pr_err("phy_buf is NULL or phy_buf_len = 0\n");
+		return sgl_cnt;
+	}
+
+	num_bd = (phy_buf_len + (XDMA_MAX_TRANS_LEN - 1))
+		/ XDMA_MAX_TRANS_LEN;
+	sgl_head = sgl;
+	sg_init_table(sgl, num_bd);
+
+	while (phy_buf_len > 0) {
+		xlnk_intptr_type page_id = phy_buf >> PAGE_SHIFT;
+		unsigned int offset = phy_buf - (page_id << PAGE_SHIFT);
+
+		sgl_cnt++;
+		if (sgl_cnt > XDMA_MAX_BD_CNT)
+			return 0;
+
+		dma_len = (phy_buf_len > XDMA_MAX_TRANS_LEN) ?
+				XDMA_MAX_TRANS_LEN : phy_buf_len;
+
+		sg_set_page(sgl_head, pfn_to_page(page_id), dma_len, offset);
+		sg_dma_address(sgl_head) = (dma_addr_t)phy_buf;
+		sg_dma_len(sgl_head) = dma_len;
+		sgl_head = sg_next(sgl_head);
+
+		phy_buf += dma_len;
+		phy_buf_len -= dma_len;
+	}
+
+	return sgl_cnt;
+}
+
+/*  merge sg list, sgl, with length sgl_len, to sgl_merged, to save dma bds */
+static unsigned int sgl_merge(struct scatterlist *sgl,
+			      unsigned int sgl_len,
+			      struct scatterlist *sgl_merged)
+{
+	struct scatterlist *sghead, *sgend, *sgnext, *sg_merged_head;
+	unsigned int sg_visited_cnt = 0, sg_merged_num = 0;
+	unsigned int dma_len = 0;
+
+	sg_init_table(sgl_merged, sgl_len);
+	sg_merged_head = sgl_merged;
+	sghead = sgl;
+
+	while (sghead && (sg_visited_cnt < sgl_len)) {
+		dma_len = sg_dma_len(sghead);
+		sgend = sghead;
+		sg_visited_cnt++;
+		sgnext = sg_next(sgend);
+
+		while (sgnext && (sg_visited_cnt < sgl_len)) {
+			if ((sg_dma_address(sgend) + sg_dma_len(sgend)) !=
+				sg_dma_address(sgnext))
+				break;
+
+			if (dma_len + sg_dma_len(sgnext) >= XDMA_MAX_TRANS_LEN)
+				break;
+
+			sgend = sgnext;
+			dma_len += sg_dma_len(sgend);
+			sg_visited_cnt++;
+			sgnext = sg_next(sgnext);
+		}
+
+		sg_merged_num++;
+		if (sg_merged_num > XDMA_MAX_BD_CNT)
+			return 0;
+
+		memcpy(sg_merged_head, sghead, sizeof(struct scatterlist));
+
+		sg_dma_len(sg_merged_head) = dma_len;
+
+		sg_merged_head = sg_next(sg_merged_head);
+		sghead = sg_next(sgend);
+	}
+
+	return sg_merged_num;
+}
+
+static int xdma_pin_user_pages(xlnk_intptr_type uaddr, unsigned int ulen,
+			       int write, struct scatterlist **scatterpp,
+			       unsigned int *cntp, unsigned int user_flags)
+{
+	int status;
+	struct mm_struct *mm = current->mm;
+	unsigned int first_page;
+	unsigned int last_page;
+	unsigned int num_pages;
+	struct scatterlist *sglist;
+	struct page **mapped_pages;
+
+	unsigned int pgidx;
+	unsigned int pglen;
+	unsigned int pgoff;
+	unsigned int sublen;
+
+	first_page = uaddr / PAGE_SIZE;
+	last_page = (uaddr + ulen - 1) / PAGE_SIZE;
+	num_pages = last_page - first_page + 1;
+	mapped_pages = vmalloc(sizeof(*mapped_pages) * num_pages);
+	if (!mapped_pages)
+		return -ENOMEM;
+
+	down_read(&mm->mmap_lock);
+	status = get_user_pages(uaddr, num_pages,
+				(write ? FOLL_WRITE : 0) | FOLL_FORCE,
+				mapped_pages, NULL);
+	up_read(&mm->mmap_lock);
+
+	if (status == num_pages) {
+		sglist = kcalloc(num_pages,
+				 sizeof(struct scatterlist),
+				 GFP_KERNEL);
+		if (!sglist) {
+			pr_err("%s: kcalloc failed to create sg list\n",
+			       __func__);
+			vfree(mapped_pages);
+			return -ENOMEM;
+		}
+		sg_init_table(sglist, num_pages);
+		sublen = 0;
+		for (pgidx = 0; pgidx < status; pgidx++) {
+			if (pgidx == 0 && num_pages != 1) {
+				pgoff = uaddr & (~PAGE_MASK);
+				pglen = PAGE_SIZE - pgoff;
+			} else if (pgidx == 0 && num_pages == 1) {
+				pgoff = uaddr & (~PAGE_MASK);
+				pglen = ulen;
+			} else if (pgidx == num_pages - 1) {
+				pgoff = 0;
+				pglen = ulen - sublen;
+			} else {
+				pgoff = 0;
+				pglen = PAGE_SIZE;
+			}
+
+			sublen += pglen;
+
+			sg_set_page(&sglist[pgidx],
+				    mapped_pages[pgidx],
+				    pglen, pgoff);
+
+			sg_dma_len(&sglist[pgidx]) = pglen;
+		}
+
+		*scatterpp = sglist;
+		*cntp = num_pages;
+
+		vfree(mapped_pages);
+		return 0;
+	}
+	pr_err("Failed to pin user pages\n");
+	for (pgidx = 0; pgidx < status; pgidx++)
+		put_page(mapped_pages[pgidx]);
+	vfree(mapped_pages);
+	return -ENOMEM;
+}
+
+static int xdma_unpin_user_pages(struct scatterlist *sglist, unsigned int cnt)
+{
+	struct page *pg;
+	unsigned int i;
+
+	if (!sglist)
+		return 0;
+
+	for (i = 0; i < cnt; i++) {
+		pg = sg_page(sglist + i);
+		if (pg)
+			put_page(pg);
+	}
+
+	kfree(sglist);
+	return 0;
+}
+
+struct xdma_chan *xdma_request_channel(char *name)
+{
+	int i;
+	struct xdma_device *device, *tmp;
+
+	list_for_each_entry_safe(device, tmp, &dma_device_list, node) {
+		for (i = 0; i < device->channel_count; i++) {
+			if (!strcmp(device->chan[i]->name, name))
+				return device->chan[i];
+		}
+	}
+	return NULL;
+}
+EXPORT_SYMBOL(xdma_request_channel);
+
+void xdma_release_channel(struct xdma_chan *chan)
+{ }
+EXPORT_SYMBOL(xdma_release_channel);
+
+void xdma_release_all_channels(void)
+{
+	int i;
+	struct xdma_device *device, *tmp;
+
+	list_for_each_entry_safe(device, tmp, &dma_device_list, node) {
+		for (i = 0; i < device->channel_count; i++) {
+			if (device->chan[i]->client_count) {
+				dma_halt(device->chan[i]);
+				xilinx_chan_desc_reinit(device->chan[i]);
+				pr_info("%s: chan %s freed\n",
+					__func__,
+					device->chan[i]->name);
+			}
+		}
+	}
+}
+EXPORT_SYMBOL(xdma_release_all_channels);
+
+static void xdma_release(struct device *dev)
+{
+}
+
+int xdma_submit(struct xdma_chan *chan,
+		xlnk_intptr_type userbuf,
+		void *kaddr,
+		unsigned int size,
+		unsigned int nappwords_i,
+		u32 *appwords_i,
+		unsigned int nappwords_o,
+		unsigned int user_flags,
+		struct xdma_head **dmaheadpp,
+		struct xlnk_dmabuf_reg *dp)
+{
+	struct xdma_head *dmahead;
+	struct scatterlist *pagelist = NULL;
+	struct scatterlist *sglist = NULL;
+	unsigned int pagecnt = 0;
+	unsigned int sgcnt = 0;
+	enum dma_data_direction dmadir;
+	int status;
+	unsigned long attrs = 0;
+
+	dmahead = kzalloc(sizeof(*dmahead), GFP_KERNEL);
+	if (!dmahead)
+		return -ENOMEM;
+
+	dmahead->chan = chan;
+	dmahead->userbuf = userbuf;
+	dmahead->size = size;
+	dmahead->dmadir = chan->direction;
+	dmahead->userflag = user_flags;
+	dmahead->dmabuf = dp;
+	dmadir = chan->direction;
+
+	if (!(user_flags & CF_FLAG_CACHE_FLUSH_INVALIDATE))
+		attrs |= DMA_ATTR_SKIP_CPU_SYNC;
+
+	if (dp) {
+		int i;
+		struct scatterlist *sg;
+		unsigned int remaining_size = size;
+
+		if (IS_ERR_OR_NULL(dp->dbuf_sg_table)) {
+			pr_err("%s dmabuf not mapped: %p\n",
+			       __func__, dp->dbuf_sg_table);
+			return -EINVAL;
+		}
+		if (dp->dbuf_sg_table->nents == 0) {
+			pr_err("%s: cannot map a scatterlist with 0 entries\n",
+			       __func__);
+			return -EINVAL;
+		}
+		sglist = kmalloc_array(dp->dbuf_sg_table->nents,
+				       sizeof(*sglist),
+				       GFP_KERNEL);
+		if (!sglist)
+			return -ENOMEM;
+
+		sg_init_table(sglist, dp->dbuf_sg_table->nents);
+		sgcnt = 0;
+		for_each_sg(dp->dbuf_sg_table->sgl,
+			    sg,
+			    dp->dbuf_sg_table->nents,
+			    i) {
+			sg_set_page(sglist + i,
+				    sg_page(sg),
+				    sg_dma_len(sg),
+				    sg->offset);
+			sg_dma_address(sglist + i) = sg_dma_address(sg);
+			if (remaining_size == 0) {
+				sg_dma_len(sglist + i) = 0;
+			} else if (sg_dma_len(sg) > remaining_size) {
+				sg_dma_len(sglist + i) = remaining_size;
+				sgcnt++;
+			} else {
+				sg_dma_len(sglist + i) = sg_dma_len(sg);
+				remaining_size -= sg_dma_len(sg);
+				sgcnt++;
+			}
+		}
+		dmahead->userbuf = (xlnk_intptr_type)sglist->dma_address;
+		pagelist = NULL;
+		pagecnt = 0;
+	} else if (user_flags & CF_FLAG_PHYSICALLY_CONTIGUOUS) {
+		size_t elem_cnt;
+
+		elem_cnt = DIV_ROUND_UP(size, XDMA_MAX_TRANS_LEN);
+		sglist = kmalloc_array(elem_cnt, sizeof(*sglist), GFP_KERNEL);
+		sgcnt = phy_buf_to_sgl(userbuf, size, sglist);
+		if (!sgcnt)
+			return -ENOMEM;
+
+		status = get_dma_ops(chan->dev)->map_sg(chan->dev,
+							sglist,
+							sgcnt,
+							dmadir,
+							attrs);
+
+		if (!status) {
+			pr_err("sg contiguous mapping failed\n");
+			return -ENOMEM;
+		}
+		pagelist = NULL;
+		pagecnt = 0;
+	} else {
+		status = xdma_pin_user_pages(userbuf, size,
+					     dmadir != DMA_TO_DEVICE, &pagelist,
+					     &pagecnt, user_flags);
+		if (status < 0) {
+			pr_err("xdma_pin_user_pages failed\n");
+			return status;
+		}
+
+		status = get_dma_ops(chan->dev)->map_sg(chan->dev,
+							pagelist,
+							pagecnt,
+							dmadir,
+							attrs);
+		if (!status) {
+			pr_err("dma_map_sg failed\n");
+			xdma_unpin_user_pages(pagelist, pagecnt);
+			return -ENOMEM;
+		}
+
+		sglist = kmalloc_array(pagecnt, sizeof(*sglist), GFP_KERNEL);
+		if (sglist)
+			sgcnt = sgl_merge(pagelist, pagecnt, sglist);
+		if (!sgcnt) {
+			get_dma_ops(chan->dev)->unmap_sg(chan->dev,
+							 pagelist,
+							 pagecnt,
+							 dmadir,
+							 attrs);
+			xdma_unpin_user_pages(pagelist, pagecnt);
+			kfree(sglist);
+			return -ENOMEM;
+		}
+	}
+	dmahead->sglist = sglist;
+	dmahead->sgcnt = sgcnt;
+	dmahead->pagelist = pagelist;
+	dmahead->pagecnt = pagecnt;
+
+	/* skipping config */
+	init_completion(&dmahead->cmp);
+
+	if (nappwords_i > XDMA_MAX_APPWORDS)
+		nappwords_i = XDMA_MAX_APPWORDS;
+
+	if (nappwords_o > XDMA_MAX_APPWORDS)
+		nappwords_o = XDMA_MAX_APPWORDS;
+
+	dmahead->nappwords_o = nappwords_o;
+
+	status = xdma_setup_hw_desc(chan, dmahead, sglist, sgcnt,
+				    dmadir, nappwords_i, appwords_i);
+	if (status) {
+		pr_err("setup hw desc failed\n");
+		if (dmahead->pagelist) {
+			get_dma_ops(chan->dev)->unmap_sg(chan->dev,
+							 pagelist,
+							 pagecnt,
+							 dmadir,
+							 attrs);
+			xdma_unpin_user_pages(pagelist, pagecnt);
+		} else if (!dp) {
+			get_dma_ops(chan->dev)->unmap_sg(chan->dev,
+							 sglist,
+							 sgcnt,
+							 dmadir,
+							 attrs);
+		}
+		kfree(dmahead->sglist);
+		return -ENOMEM;
+	}
+
+	*dmaheadpp = dmahead;
+	return 0;
+}
+EXPORT_SYMBOL(xdma_submit);
+
+int xdma_wait(struct xdma_head *dmahead,
+	      unsigned int user_flags,
+	      unsigned int *operating_flags)
+{
+	struct xdma_chan *chan = dmahead->chan;
+	unsigned long attrs = 0;
+
+	if (chan->poll_mode) {
+		xilinx_chan_desc_cleanup(chan);
+		*operating_flags |= XDMA_FLAGS_WAIT_COMPLETE;
+	} else {
+		if (*operating_flags & XDMA_FLAGS_TRYWAIT) {
+			if (!try_wait_for_completion(&dmahead->cmp))
+				return 0;
+			*operating_flags |= XDMA_FLAGS_WAIT_COMPLETE;
+		} else {
+			wait_for_completion(&dmahead->cmp);
+			*operating_flags |= XDMA_FLAGS_WAIT_COMPLETE;
+		}
+	}
+
+	if (!dmahead->dmabuf) {
+		if (!(user_flags & CF_FLAG_CACHE_FLUSH_INVALIDATE))
+			attrs |= DMA_ATTR_SKIP_CPU_SYNC;
+
+		if (user_flags & CF_FLAG_PHYSICALLY_CONTIGUOUS) {
+			get_dma_ops(chan->dev)->unmap_sg(chan->dev,
+							 dmahead->sglist,
+							 dmahead->sgcnt,
+							 dmahead->dmadir,
+							 attrs);
+		} else {
+			get_dma_ops(chan->dev)->unmap_sg(chan->dev,
+							 dmahead->pagelist,
+							 dmahead->pagecnt,
+							 dmahead->dmadir,
+							 attrs);
+			xdma_unpin_user_pages(dmahead->pagelist,
+					      dmahead->pagecnt);
+		}
+	}
+	kfree(dmahead->sglist);
+
+	return 0;
+}
+EXPORT_SYMBOL(xdma_wait);
+
+int xdma_getconfig(struct xdma_chan *chan,
+		   unsigned char *irq_thresh,
+		   unsigned char *irq_delay)
+{
+	*irq_thresh = (DMA_IN(&chan->regs->cr) >> XDMA_COALESCE_SHIFT) & 0xff;
+	*irq_delay = (DMA_IN(&chan->regs->cr) >> XDMA_DELAY_SHIFT) & 0xff;
+	return 0;
+}
+EXPORT_SYMBOL(xdma_getconfig);
+
+int xdma_setconfig(struct xdma_chan *chan,
+		   unsigned char irq_thresh,
+		   unsigned char irq_delay)
+{
+	unsigned long val;
+
+	if (dma_is_running(chan))
+		return -EBUSY;
+
+	val = DMA_IN(&chan->regs->cr);
+	val &= ~((0xff << XDMA_COALESCE_SHIFT) |
+				(0xff << XDMA_DELAY_SHIFT));
+	val |= ((irq_thresh << XDMA_COALESCE_SHIFT) |
+				(irq_delay << XDMA_DELAY_SHIFT));
+
+	DMA_OUT(&chan->regs->cr, val);
+	return 0;
+}
+EXPORT_SYMBOL(xdma_setconfig);
+
+static const struct of_device_id gic_match[] = {
+	{ .compatible = "arm,cortex-a9-gic", },
+	{ .compatible = "arm,cortex-a15-gic", },
+	{ },
+};
+
+static struct device_node *gic_node;
+
+unsigned int xlate_irq(unsigned int hwirq)
+{
+	struct of_phandle_args irq_data;
+	unsigned int irq;
+
+	if (!gic_node)
+		gic_node = of_find_matching_node(NULL, gic_match);
+
+	if (WARN_ON(!gic_node))
+		return hwirq;
+
+	irq_data.np = gic_node;
+	irq_data.args_count = 3;
+	irq_data.args[0] = 0;
+#if XLNK_SYS_BIT_WIDTH == 32
+	irq_data.args[1] = hwirq - 32; /* GIC SPI offset */
+#else
+	irq_data.args[1] = hwirq;
+#endif
+	irq_data.args[2] = IRQ_TYPE_LEVEL_HIGH;
+
+	irq = irq_create_of_mapping(&irq_data);
+	if (WARN_ON(!irq))
+		irq = hwirq;
+
+	pr_info("%s: hwirq %d, irq %d\n", __func__, hwirq, irq);
+
+	return irq;
+}
+
+/* Brute-force probing for xilinx DMA
+ */
+static int xdma_probe(struct platform_device *pdev)
+{
+	struct xdma_device *xdev;
+	struct resource *res;
+	int err, i, j;
+	struct xdma_chan *chan;
+	struct xdma_device_config *dma_config;
+	int dma_chan_dir;
+	int dma_chan_reg_offset;
+
+	pr_info("%s: probe dma %p, nres %d, id %d\n", __func__,
+		&pdev->dev, pdev->num_resources, pdev->id);
+
+	xdev = devm_kzalloc(&pdev->dev, sizeof(struct xdma_device), GFP_KERNEL);
+	if (!xdev)
+		return -ENOMEM;
+	xdev->dev = &pdev->dev;
+
+	/* Set this as configurable once HPC works */
+	arch_setup_dma_ops(&pdev->dev, 0, 0, NULL, false);
+	dma_set_mask(&pdev->dev, 0xFFFFFFFFFFFFFFFFull);
+
+	dma_config = (struct xdma_device_config *)xdev->dev->platform_data;
+	if (dma_config->channel_count < 1 || dma_config->channel_count > 2)
+		return -EFAULT;
+
+	/* Get the memory resource */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xdev->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (!xdev->regs) {
+		dev_err(&pdev->dev, "unable to iomap registers\n");
+		return -EFAULT;
+	}
+
+	dev_info(&pdev->dev, "AXIDMA device %d physical base address=%pa\n",
+		 pdev->id, &res->start);
+	dev_info(&pdev->dev, "AXIDMA device %d remapped to %pa\n",
+		 pdev->id, &xdev->regs);
+
+	/* Allocate the channels */
+
+	dev_info(&pdev->dev, "has %d channel(s)\n", dma_config->channel_count);
+	for (i = 0; i < dma_config->channel_count; i++) {
+		chan = devm_kzalloc(&pdev->dev, sizeof(*chan), GFP_KERNEL);
+		if (!chan)
+			return -ENOMEM;
+
+		dma_chan_dir = strcmp(dma_config->channel_config[i].type,
+				      "axi-dma-mm2s-channel") ?
+					DMA_FROM_DEVICE :
+					DMA_TO_DEVICE;
+		dma_chan_reg_offset = (dma_chan_dir == DMA_TO_DEVICE) ?
+					0 :
+					0x30;
+
+		/* Initialize channel parameters */
+		chan->id = i;
+		chan->regs = xdev->regs + dma_chan_reg_offset;
+		/* chan->regs = xdev->regs; */
+		chan->dev = xdev->dev;
+		chan->max_len = XDMA_MAX_TRANS_LEN;
+		chan->direction = dma_chan_dir;
+		sprintf(chan->name, "%s:%d", dma_config->name, chan->id);
+		pr_info("  chan %d name: %s\n", chan->id, chan->name);
+		pr_info("  chan %d direction: %s\n", chan->id,
+			dma_chan_dir == DMA_FROM_DEVICE ?
+				"FROM_DEVICE" : "TO_DEVICE");
+
+		spin_lock_init(&chan->lock);
+		tasklet_init(&chan->tasklet,
+			     xdma_tasklet,
+			     (unsigned long)chan);
+		tasklet_init(&chan->dma_err_tasklet,
+			     xdma_err_tasklet,
+			     (unsigned long)chan);
+
+		xdev->chan[chan->id] = chan;
+
+		/* The IRQ resource */
+		chan->irq = xlate_irq(dma_config->channel_config[i].irq);
+		if (chan->irq <= 0) {
+			pr_err("get_resource for IRQ for dev %d failed\n",
+			       pdev->id);
+			return -ENODEV;
+		}
+
+		err = devm_request_irq(&pdev->dev,
+				       chan->irq,
+				       dma_chan_dir == DMA_TO_DEVICE ?
+					xdma_tx_intr_handler :
+					xdma_rx_intr_handler,
+				       IRQF_SHARED,
+				       pdev->name,
+				       chan);
+		if (err) {
+			dev_err(&pdev->dev, "unable to request IRQ\n");
+			return err;
+		}
+		pr_info("  chan%d irq: %d\n", chan->id, chan->irq);
+
+		chan->poll_mode = dma_config->channel_config[i].poll_mode;
+		pr_info("  chan%d poll mode: %s\n",
+			chan->id,
+			chan->poll_mode ? "on" : "off");
+
+		/* Allocate channel BD's */
+		err = xdma_alloc_chan_descriptors(xdev->chan[chan->id]);
+		if (err) {
+			dev_err(&pdev->dev, "unable to allocate BD's\n");
+			return -ENOMEM;
+		}
+		pr_info("  chan%d bd ring @ 0x%p (size: 0x%x bytes)\n",
+			chan->id,
+			(void *)chan->bd_phys_addr,
+			chan->bd_chain_size);
+
+		err = dma_init(xdev->chan[chan->id]);
+		if (err) {
+			dev_err(&pdev->dev, "DMA init failed\n");
+			/* FIXME Check this - unregister all chan resources */
+			for (j = 0; j <= i; j++)
+				xdma_free_chan_resources(xdev->chan[j]);
+			return -EIO;
+		}
+	}
+	xdev->channel_count = dma_config->channel_count;
+	pdev->dev.release = xdma_release;
+	/* Add the DMA device to the global list */
+	mutex_lock(&dma_list_mutex);
+	list_add_tail(&xdev->node, &dma_device_list);
+	mutex_unlock(&dma_list_mutex);
+
+	platform_set_drvdata(pdev, xdev);
+
+	return 0;
+}
+
+static int xdma_remove(struct platform_device *pdev)
+{
+	int i;
+	struct xdma_device *xdev = platform_get_drvdata(pdev);
+
+	/* Remove the DMA device from the global list */
+	mutex_lock(&dma_list_mutex);
+	list_del(&xdev->node);
+	mutex_unlock(&dma_list_mutex);
+
+	for (i = 0; i < XDMA_MAX_CHANS_PER_DEVICE; i++) {
+		if (xdev->chan[i])
+			xdma_free_chan_resources(xdev->chan[i]);
+	}
+
+	return 0;
+}
+
+static struct platform_driver xdma_driver = {
+	.probe = xdma_probe,
+	.remove = xdma_remove,
+	.driver = {
+		.name = "xilinx-axidma",
+	},
+};
+
+module_platform_driver(xdma_driver);
+
+MODULE_DESCRIPTION("Xilinx DMA driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xilinx-dma-apf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xilinx-dma-apf.h
@@ -0,0 +1,229 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Xilinx AXI DMA Engine support
+ *
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ */
+
+#ifndef __XILINX_DMA_APF_H
+#define __XILINX_DMA_APF_H
+
+/* ioctls */
+#include <linux/ioctl.h>
+
+/* tasklet */
+#include <linux/interrupt.h>
+
+/* dma stuff */
+#include <linux/dma-mapping.h>
+
+/* xlnk structures */
+#include "xlnk.h"
+#include "xlnk-sysdef.h"
+
+#define XDMA_IOC_MAGIC 'X'
+#define XDMA_IOCRESET		_IO(XDMA_IOC_MAGIC, 0)
+#define XDMA_IOCREQUEST		_IOWR(XDMA_IOC_MAGIC, 1, unsigned long)
+#define XDMA_IOCRELEASE		_IOWR(XDMA_IOC_MAGIC, 2, unsigned long)
+#define XDMA_IOCSUBMIT		_IOWR(XDMA_IOC_MAGIC, 3, unsigned long)
+#define XDMA_IOCWAIT		_IOWR(XDMA_IOC_MAGIC, 4, unsigned long)
+#define XDMA_IOCGETCONFIG	_IOWR(XDMA_IOC_MAGIC, 5, unsigned long)
+#define XDMA_IOCSETCONFIG	_IOWR(XDMA_IOC_MAGIC, 6, unsigned long)
+#define XDMA_IOC_MAXNR		6
+
+/* Specific hardware configuration-related constants
+ */
+#define XDMA_RESET_LOOP            1000000
+#define XDMA_HALT_LOOP             1000000
+#define XDMA_NO_CHANGE             0xFFFF
+
+/* General register bits definitions
+ */
+#define XDMA_CR_RESET_MASK    0x00000004  /* Reset DMA engine */
+#define XDMA_CR_RUNSTOP_MASK  0x00000001  /* Start/stop DMA engine */
+
+#define XDMA_SR_HALTED_MASK   0x00000001  /* DMA channel halted */
+#define XDMA_SR_IDLE_MASK     0x00000002  /* DMA channel idle */
+
+#define XDMA_SR_ERR_INTERNAL_MASK 0x00000010/* Datamover internal err */
+#define XDMA_SR_ERR_SLAVE_MASK    0x00000020 /* Datamover slave err */
+#define XDMA_SR_ERR_DECODE_MASK   0x00000040 /* Datamover decode err */
+#define XDMA_SR_ERR_SG_INT_MASK   0x00000100 /* SG internal err */
+#define XDMA_SR_ERR_SG_SLV_MASK   0x00000200 /* SG slave err */
+#define XDMA_SR_ERR_SG_DEC_MASK   0x00000400 /* SG decode err */
+#define XDMA_SR_ERR_ALL_MASK      0x00000770 /* All errors */
+
+#define XDMA_XR_IRQ_IOC_MASK	0x00001000 /* Completion interrupt */
+#define XDMA_XR_IRQ_DELAY_MASK	0x00002000 /* Delay interrupt */
+#define XDMA_XR_IRQ_ERROR_MASK	0x00004000 /* Error interrupt */
+#define XDMA_XR_IRQ_ALL_MASK	    0x00007000 /* All interrupts */
+
+#define XDMA_XR_DELAY_MASK    0xFF000000 /* Delay timeout counter */
+#define XDMA_XR_COALESCE_MASK 0x00FF0000 /* Coalesce counter */
+
+#define XDMA_DELAY_SHIFT    24
+#define XDMA_COALESCE_SHIFT 16
+
+#define XDMA_DELAY_MAX     0xFF /**< Maximum delay counter value */
+#define XDMA_COALESCE_MAX  0xFF /**< Maximum coalescing counter value */
+
+/* BD definitions for Axi DMA
+ */
+#define XDMA_BD_STS_ACTUAL_LEN_MASK	0x007FFFFF
+#define XDMA_BD_STS_COMPL_MASK 0x80000000
+#define XDMA_BD_STS_ERR_MASK   0x70000000
+#define XDMA_BD_STS_ALL_MASK   0xF0000000
+
+/* DMA BD special bits definitions
+ */
+#define XDMA_BD_SOP       0x08000000    /* Start of packet bit */
+#define XDMA_BD_EOP       0x04000000    /* End of packet bit */
+
+/* BD Software Flag definitions for Axi DMA
+ */
+#define XDMA_BD_SF_POLL_MODE_MASK	0x00000002
+#define XDMA_BD_SF_SW_DONE_MASK		0x00000001
+
+/* driver defines */
+#define XDMA_MAX_BD_CNT			16384
+#define XDMA_MAX_CHANS_PER_DEVICE	2
+#define XDMA_MAX_TRANS_LEN		0x7FF000
+#define XDMA_MAX_APPWORDS		5
+#define XDMA_BD_CLEANUP_THRESHOLD	((XDMA_MAX_BD_CNT * 8) / 10)
+
+#define XDMA_FLAGS_WAIT_COMPLETE 1
+#define XDMA_FLAGS_TRYWAIT 2
+
+/* Platform data definition until ARM supports device tree */
+struct xdma_channel_config {
+	char *type;
+	unsigned int include_dre;
+	unsigned int datawidth;
+	unsigned int max_burst_len;
+	unsigned int irq;
+	unsigned int poll_mode;
+	unsigned int lite_mode;
+};
+
+struct xdma_device_config {
+	char *type;
+	char *name;
+	unsigned int include_sg;
+	unsigned int sg_include_stscntrl_strm;  /* dma only */
+	unsigned int channel_count;
+	struct xdma_channel_config *channel_config;
+};
+
+struct xdma_desc_hw {
+	xlnk_intptr_type next_desc;	/* 0x00 */
+#if XLNK_SYS_BIT_WIDTH == 32
+	u32 pad1;       /* 0x04 */
+#endif
+	xlnk_intptr_type src_addr;   /* 0x08 */
+#if XLNK_SYS_BIT_WIDTH == 32
+	u32 pad2;       /* 0x0c */
+#endif
+	u32 addr_vsize; /* 0x10 */
+	u32 hsize;       /* 0x14 */
+	u32 control;    /* 0x18 */
+	u32 status;     /* 0x1c */
+	u32 app[5];      /* 0x20 */
+	xlnk_intptr_type dmahead;
+#if XLNK_SYS_BIT_WIDTH == 32
+	u32 Reserved0;
+#endif
+	u32 sw_flag;	/* 0x3C */
+} __aligned(64);
+
+/* shared by all Xilinx DMA engines */
+struct xdma_regs {
+	u32 cr;        /* 0x00 Control Register */
+	u32 sr;        /* 0x04 Status Register */
+	u32 cdr;       /* 0x08 Current Descriptor Register */
+	u32 cdr_hi;
+	u32 tdr;       /* 0x10 Tail Descriptor Register */
+	u32 tdr_hi;
+	u32 src;       /* 0x18 Source Address Register (cdma) */
+	u32 src_hi;
+	u32 dst;       /* 0x20 Destination Address Register (cdma) */
+	u32 dst_hi;
+	u32 btt_ref;   /* 0x28 Bytes To Transfer (cdma) or
+			*		park_ref (vdma)
+			*/
+	u32 version;   /* 0x2c version (vdma) */
+};
+
+/* Per DMA specific operations should be embedded in the channel structure */
+struct xdma_chan {
+	char name[64];
+	struct xdma_regs __iomem *regs;
+	struct device *dev;			/* The dma device */
+	struct xdma_desc_hw *bds[XDMA_MAX_BD_CNT];
+	dma_addr_t bd_phys_addr;
+	u32 bd_chain_size;
+	int bd_cur;
+	int bd_tail;
+	unsigned int bd_used;			/* # of BDs passed to hw chan */
+	enum dma_data_direction direction;	/* Transfer direction */
+	int id;					/* Channel ID */
+	int irq;				/* Channel IRQ */
+	int poll_mode;				/* Poll mode turned on? */
+	spinlock_t lock;			/* Descriptor operation lock */
+	struct tasklet_struct tasklet;		/* Cleanup work after irq */
+	struct tasklet_struct dma_err_tasklet;	/* Cleanup work after irq */
+	int    max_len;				/* Maximum len per transfer */
+	int    err;				/* Channel has errors */
+	int    client_count;
+};
+
+struct xdma_device {
+	void __iomem *regs;
+	struct device *dev;
+	struct list_head node;
+	struct xdma_chan *chan[XDMA_MAX_CHANS_PER_DEVICE];
+	u8 channel_count;
+};
+
+struct xdma_head {
+	xlnk_intptr_type userbuf;
+	unsigned int size;
+	unsigned int dmaflag;
+	enum dma_data_direction dmadir;
+	struct scatterlist *sglist;
+	unsigned int sgcnt;
+	struct scatterlist *pagelist;
+	unsigned int pagecnt;
+	struct completion cmp;
+	struct xdma_chan *chan;
+	unsigned int nappwords_o;
+	u32 appwords_o[XDMA_MAX_APPWORDS];
+	unsigned int userflag;
+	u32 last_bd_index;
+	struct xlnk_dmabuf_reg *dmabuf;
+};
+
+struct xdma_chan *xdma_request_channel(char *name);
+void xdma_release_channel(struct xdma_chan *chan);
+void xdma_release_all_channels(void);
+int xdma_submit(struct xdma_chan *chan,
+		xlnk_intptr_type userbuf,
+		void *kaddr,
+		unsigned int size,
+		unsigned int nappwords_i,
+		u32 *appwords_i,
+		unsigned int nappwords_o,
+		unsigned int user_flags,
+		struct xdma_head **dmaheadpp,
+		struct xlnk_dmabuf_reg *dp);
+int xdma_wait(struct xdma_head *dmahead,
+	      unsigned int user_flags,
+	      unsigned int *operating_flags);
+int xdma_getconfig(struct xdma_chan *chan,
+		   unsigned char *irq_thresh,
+		   unsigned char *irq_delay);
+int xdma_setconfig(struct xdma_chan *chan,
+		   unsigned char irq_thresh,
+		   unsigned char irq_delay);
+unsigned int xlate_irq(unsigned int hwirq);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xlnk-eng.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xlnk-eng.c
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx XLNK Engine Driver
+ *
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/spinlock_types.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/mutex.h>
+#include <linux/string.h>
+#include <linux/uio_driver.h>
+
+
+#include "xlnk-eng.h"
+
+static DEFINE_MUTEX(xlnk_eng_list_mutex);
+static LIST_HEAD(xlnk_eng_list);
+
+int xlnk_eng_register_device(struct xlnk_eng_device *xlnk_dev)
+{
+	mutex_lock(&xlnk_eng_list_mutex);
+	/* todo: need to add more error checking */
+
+	list_add_tail(&xlnk_dev->global_node, &xlnk_eng_list);
+
+	mutex_unlock(&xlnk_eng_list_mutex);
+
+	return 0;
+}
+EXPORT_SYMBOL(xlnk_eng_register_device);
+
+
+void xlnk_eng_unregister_device(struct xlnk_eng_device *xlnk_dev)
+{
+	mutex_lock(&xlnk_eng_list_mutex);
+	/* todo: need to add more error checking */
+
+	list_del(&xlnk_dev->global_node);
+
+	mutex_unlock(&xlnk_eng_list_mutex);
+}
+EXPORT_SYMBOL(xlnk_eng_unregister_device);
+
+struct xlnk_eng_device *xlnk_eng_request_by_name(char *name)
+{
+	struct xlnk_eng_device *device, *_d;
+	int found = 0;
+
+	mutex_lock(&xlnk_eng_list_mutex);
+
+	list_for_each_entry_safe(device, _d, &xlnk_eng_list, global_node) {
+		if (!strcmp(dev_name(device->dev), name)) {
+			found = 1;
+			break;
+		}
+	}
+	if (found)
+		device = device->alloc(device);
+	else
+		device = NULL;
+
+	mutex_unlock(&xlnk_eng_list_mutex);
+
+	return device;
+}
+EXPORT_SYMBOL(xlnk_eng_request_by_name);
+
+/**
+ * struct xilinx_xlnk_eng_device - device structure for xilinx_xlnk_eng
+ * @common:	common device info
+ * @base:	base address for device
+ * @lock:	lock used by device
+ * @cnt:	usage count
+ * @info:	info for registering and unregistering uio device
+ */
+struct xilinx_xlnk_eng_device {
+	struct xlnk_eng_device common;
+	void __iomem *base;
+	spinlock_t lock;
+	int cnt;
+	struct uio_info *info;
+};
+
+static void xlnk_eng_release(struct device *dev)
+{
+	struct xilinx_xlnk_eng_device *xdev;
+	struct xlnk_eng_device *xlnk_dev;
+
+	xdev = dev_get_drvdata(dev);
+	xlnk_dev = &xdev->common;
+	if (!xlnk_dev)
+		return;
+
+	xlnk_dev->free(xlnk_dev);
+}
+
+#define DRIVER_NAME "xilinx-xlnk-eng"
+
+#define to_xilinx_xlnk(dev)	container_of(dev, \
+					struct xilinx_xlnk_eng_device, common)
+
+static struct xlnk_eng_device *xilinx_xlnk_alloc(
+					struct xlnk_eng_device *xlnkdev)
+{
+	struct xilinx_xlnk_eng_device *xdev;
+	struct xlnk_eng_device *retdev;
+
+	xdev = to_xilinx_xlnk(xlnkdev);
+
+	if (xdev->cnt == 0) {
+		xdev->cnt++;
+		retdev = xlnkdev;
+	} else
+		retdev = NULL;
+
+	return retdev;
+}
+
+static void xilinx_xlnk_free(struct xlnk_eng_device *xlnkdev)
+{
+	struct xilinx_xlnk_eng_device *xdev;
+
+	xdev = to_xilinx_xlnk(xlnkdev);
+
+	xdev->cnt = 0;
+}
+
+static int xlnk_eng_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct xilinx_xlnk_eng_device *xdev;
+	struct uio_info *info;
+	char *devname;
+
+	pr_info("xlnk_eng_probe ...\n");
+	xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL);
+	if (!xdev) {
+		dev_err(&pdev->dev, "Not enough memory for device\n");
+		return -ENOMEM;
+	}
+
+	/* more error handling */
+	info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
+	if (!info) {
+		dev_err(&pdev->dev, "Not enough memory for device\n");
+		return -ENOMEM;
+	}
+	xdev->info = info;
+	devname = devm_kzalloc(&pdev->dev, 64, GFP_KERNEL);
+	if (!devname) {
+		dev_err(&pdev->dev, "Not enough memory for device\n");
+		return -ENOMEM;
+	}
+	sprintf(devname, "%s.%d", DRIVER_NAME, pdev->id);
+	pr_info("uio name %s\n", devname);
+	/* iomap registers */
+
+	/* Get the data from the platform device */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xdev->base = devm_ioremap_resource(&pdev->dev, res);
+
+	/* %pa types should be used here */
+	dev_info(&pdev->dev, "physical base : 0x%lx\n",
+		(unsigned long)res->start);
+	dev_info(&pdev->dev, "register range : 0x%lx\n",
+		(unsigned long)resource_size(res));
+	dev_info(&pdev->dev, "base remapped to: 0x%lx\n",
+		(unsigned long)xdev->base);
+	if (!xdev->base) {
+		dev_err(&pdev->dev, "unable to iomap registers\n");
+		return -ENOMEM;
+	}
+
+	info->mem[0].addr = res->start;
+	info->mem[0].size = resource_size(res);
+	info->mem[0].memtype = UIO_MEM_PHYS;
+	info->mem[0].internal_addr = xdev->base;
+
+	/* info->name = DRIVER_NAME; */
+	info->name = devname;
+	info->version = "0.0.1";
+
+	info->irq = -1;
+
+	xdev->common.dev = &pdev->dev;
+
+	xdev->common.alloc = xilinx_xlnk_alloc;
+	xdev->common.free = xilinx_xlnk_free;
+	xdev->common.dev->release = xlnk_eng_release;
+
+	dev_set_drvdata(&pdev->dev, xdev);
+
+	spin_lock_init(&xdev->lock);
+
+	xdev->cnt = 0;
+
+	xlnk_eng_register_device(&xdev->common);
+
+	if (uio_register_device(&pdev->dev, info)) {
+		dev_err(&pdev->dev, "uio_register_device failed\n");
+		return -ENODEV;
+	}
+	dev_info(&pdev->dev, "xilinx-xlnk-eng uio registered\n");
+
+	return 0;
+}
+
+static int xlnk_eng_remove(struct platform_device *pdev)
+{
+	struct uio_info *info;
+	struct xilinx_xlnk_eng_device *xdev;
+
+	xdev = dev_get_drvdata(&pdev->dev);
+	info = xdev->info;
+
+	uio_unregister_device(info);
+	dev_info(&pdev->dev, "xilinx-xlnk-eng uio unregistered\n");
+	xlnk_eng_unregister_device(&xdev->common);
+
+	return 0;
+}
+
+static struct platform_driver xlnk_eng_driver = {
+	.probe = xlnk_eng_probe,
+	.remove = xlnk_eng_remove,
+	.driver = {
+		.owner = THIS_MODULE,
+		.name = DRIVER_NAME,
+	},
+};
+
+module_platform_driver(xlnk_eng_driver);
+
+MODULE_DESCRIPTION("Xilinx xlnk engine generic driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xlnk-eng.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xlnk-eng.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx XLNK Engine Driver
+ *
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ */
+
+#ifndef XLNK_ENG_H
+#define XLNK_ENG_H
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/spinlock_types.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/mutex.h>
+#include <linux/string.h>
+
+struct xlnk_eng_device {
+	struct list_head global_node;
+	struct xlnk_eng_device * (*alloc)(struct xlnk_eng_device *xdev);
+	void (*free)(struct xlnk_eng_device *xdev);
+	struct device *dev;
+};
+extern int xlnk_eng_register_device(struct xlnk_eng_device *xlnk_dev);
+extern void xlnk_eng_unregister_device(struct xlnk_eng_device *xlnk_dev);
+extern struct xlnk_eng_device *xlnk_eng_request_by_name(char *name);
+
+#endif
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xlnk-ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xlnk-ioctl.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ */
+
+#ifndef _XLNK_IOCTL_H
+#define _XLNK_IOCTL_H
+
+#include <linux/ioctl.h>
+
+#define XLNK_IOC_MAGIC 'X'
+
+#define XLNK_IOCRESET		_IO(XLNK_IOC_MAGIC, 0)
+
+#define XLNK_IOCALLOCBUF	_IOWR(XLNK_IOC_MAGIC, 2, unsigned long)
+#define XLNK_IOCFREEBUF		_IOWR(XLNK_IOC_MAGIC, 3, unsigned long)
+#define XLNK_IOCADDDMABUF	_IOWR(XLNK_IOC_MAGIC, 4, unsigned long)
+#define XLNK_IOCCLEARDMABUF	_IOWR(XLNK_IOC_MAGIC, 5, unsigned long)
+
+#define XLNK_IOCDMAREQUEST	_IOWR(XLNK_IOC_MAGIC, 7, unsigned long)
+#define XLNK_IOCDMASUBMIT	_IOWR(XLNK_IOC_MAGIC, 8, unsigned long)
+#define XLNK_IOCDMAWAIT		_IOWR(XLNK_IOC_MAGIC, 9, unsigned long)
+#define XLNK_IOCDMARELEASE	_IOWR(XLNK_IOC_MAGIC, 10, unsigned long)
+
+#define XLNK_IOCMEMOP		_IOWR(XLNK_IOC_MAGIC, 25, unsigned long)
+#define XLNK_IOCDEVREGISTER	_IOWR(XLNK_IOC_MAGIC, 16, unsigned long)
+#define XLNK_IOCDMAREGISTER	_IOWR(XLNK_IOC_MAGIC, 17, unsigned long)
+#define XLNK_IOCDEVUNREGISTER	_IOWR(XLNK_IOC_MAGIC, 18, unsigned long)
+#define XLNK_IOCCDMAREQUEST	_IOWR(XLNK_IOC_MAGIC, 19, unsigned long)
+#define XLNK_IOCCDMASUBMIT	_IOWR(XLNK_IOC_MAGIC, 20, unsigned long)
+#define XLNK_IOCMCDMAREGISTER	_IOWR(XLNK_IOC_MAGIC, 23, unsigned long)
+#define XLNK_IOCCACHECTRL	_IOWR(XLNK_IOC_MAGIC, 24, unsigned long)
+
+#define XLNK_IOCIRQREGISTER	_IOWR(XLNK_IOC_MAGIC, 35, unsigned long)
+#define XLNK_IOCIRQUNREGISTER	_IOWR(XLNK_IOC_MAGIC, 36, unsigned long)
+#define XLNK_IOCIRQWAIT		_IOWR(XLNK_IOC_MAGIC, 37, unsigned long)
+
+#define XLNK_IOCSHUTDOWN	_IOWR(XLNK_IOC_MAGIC, 100, unsigned long)
+#define XLNK_IOCRECRES		_IOWR(XLNK_IOC_MAGIC, 101, unsigned long)
+#define XLNK_IOC_MAXNR		101
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xlnk-sysdef.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xlnk-sysdef.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ */
+
+#ifndef XLNK_SYSDEF_H
+#define XLNK_SYSDEF_H
+
+#if __SIZEOF_POINTER__  == 4
+	#define XLNK_SYS_BIT_WIDTH 32
+#elif __SIZEOF_POINTER__  == 8
+	#define XLNK_SYS_BIT_WIDTH 64
+#endif
+
+#include <linux/types.h>
+
+#if XLNK_SYS_BIT_WIDTH == 32
+
+	typedef u32 xlnk_intptr_type;
+	typedef s32 xlnk_int_type;
+	typedef u32 xlnk_uint_type;
+	typedef u8 xlnk_byte_type;
+	typedef s8 xlnk_char_type;
+	#define xlnk_enum_type s32
+
+#elif XLNK_SYS_BIT_WIDTH == 64
+
+	typedef u64 xlnk_intptr_type;
+	typedef s32 xlnk_int_type;
+	typedef u32 xlnk_uint_type;
+	typedef u8 xlnk_byte_type;
+	typedef s8 xlnk_char_type;
+	#define xlnk_enum_type s32
+
+#else
+	#error "Please define application bit width and system bit width"
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xlnk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xlnk.c
@@ -0,0 +1,1511 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Accelerator driver support.
+ *
+ * Copyright (C) 2010 Xilinx Inc.
+ */
+
+/*  ----------------------------------- Host OS */
+
+#include <asm/cacheflush.h>
+
+#include <linux/cdev.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/dma-map-ops.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
+#include <linux/fs.h>
+#include <linux/gfp.h>
+#include <linux/io.h>
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pagemap.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/sched.h>
+#include <linux/semaphore.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+#include <linux/wait.h>
+
+#include "xlnk-ioctl.h"
+#include "xlnk-sysdef.h"
+#include "xlnk.h"
+
+#ifdef CONFIG_XILINX_DMA_APF
+#include "xilinx-dma-apf.h"
+#endif
+
+#define DRIVER_NAME  "xlnk"
+
+static struct platform_device *xlnk_pdev;
+static struct device *xlnk_dev;
+
+static struct cdev xlnk_cdev;
+
+static struct class *xlnk_class;
+
+static s32 driver_major;
+
+static void *xlnk_dev_buf;
+static ssize_t xlnk_dev_size;
+
+#define XLNK_BUF_POOL_SIZE	4096
+static void *xlnk_bufpool[XLNK_BUF_POOL_SIZE];
+static void *xlnk_bufpool_alloc_point[XLNK_BUF_POOL_SIZE];
+static xlnk_intptr_type xlnk_userbuf[XLNK_BUF_POOL_SIZE];
+static int xlnk_buf_process[XLNK_BUF_POOL_SIZE];
+static dma_addr_t xlnk_phyaddr[XLNK_BUF_POOL_SIZE];
+static size_t xlnk_buflen[XLNK_BUF_POOL_SIZE];
+static unsigned int xlnk_bufcacheable[XLNK_BUF_POOL_SIZE];
+static struct file *xlnk_buf_filp[XLNK_BUF_POOL_SIZE];
+static spinlock_t xlnk_buf_lock;
+
+#define XLNK_IRQ_POOL_SIZE 256
+static struct xlnk_irq_control *xlnk_irq_set[XLNK_IRQ_POOL_SIZE];
+static spinlock_t xlnk_irq_lock;
+
+LIST_HEAD(xlnk_dmabuf_list);
+
+#define MAX_XLNK_DMAS 128
+
+struct xlnk_device_pack {
+	char name[64];
+	struct platform_device pdev;
+	struct resource res[8];
+	int refs;
+
+#ifdef CONFIG_XILINX_DMA_APF
+	struct xdma_channel_config dma_chan_cfg[4];  /* for xidane dma only */
+	struct xdma_device_config dma_dev_cfg;	   /* for xidane dma only */
+#endif
+};
+
+static struct semaphore xlnk_devpack_sem;
+static struct xlnk_device_pack *xlnk_devpacks[MAX_XLNK_DMAS];
+static void xlnk_devpacks_init(void)
+{
+	unsigned int i;
+
+	sema_init(&xlnk_devpack_sem, 1);
+	for (i = 0; i < MAX_XLNK_DMAS; i++)
+		xlnk_devpacks[i] = NULL;
+}
+
+static struct xlnk_device_pack *xlnk_devpacks_alloc(void)
+{
+	unsigned int i;
+
+	for (i = 0; i < MAX_XLNK_DMAS; i++) {
+		if (!xlnk_devpacks[i]) {
+			struct xlnk_device_pack *ret;
+
+			ret = kzalloc(sizeof(*ret), GFP_KERNEL);
+			ret->pdev.id = i;
+			xlnk_devpacks[i] = ret;
+
+			return ret;
+		}
+	}
+
+	return NULL;
+}
+
+static void xlnk_devpacks_delete(struct xlnk_device_pack *devpack)
+{
+	unsigned int i;
+
+	for (i = 0; i < MAX_XLNK_DMAS; i++)
+		if (xlnk_devpacks[i] == devpack)
+			xlnk_devpacks[i] = NULL;
+	kfree(devpack);
+}
+
+static struct xlnk_device_pack *xlnk_devpacks_find(xlnk_intptr_type base)
+{
+	unsigned int i;
+
+	for (i = 0; i < MAX_XLNK_DMAS; i++) {
+		if (xlnk_devpacks[i] &&
+		    xlnk_devpacks[i]->res[0].start == base)
+			return xlnk_devpacks[i];
+	}
+	return NULL;
+}
+
+static void xlnk_devpacks_free(xlnk_intptr_type base)
+{
+	struct xlnk_device_pack *devpack;
+
+	down(&xlnk_devpack_sem);
+	devpack = xlnk_devpacks_find(base);
+	if (!devpack) {
+		up(&xlnk_devpack_sem);
+		return;
+	}
+	devpack->refs--;
+	if (devpack->refs) {
+		up(&xlnk_devpack_sem);
+		return;
+	}
+	platform_device_unregister(&devpack->pdev);
+	xlnk_devpacks_delete(devpack);
+	kfree(devpack);
+	up(&xlnk_devpack_sem);
+}
+
+static void xlnk_devpacks_free_all(void)
+{
+	struct xlnk_device_pack *devpack;
+	unsigned int i;
+
+	for (i = 0; i < MAX_XLNK_DMAS; i++) {
+		devpack = xlnk_devpacks[i];
+		if (devpack) {
+			platform_device_unregister(&devpack->pdev);
+			xlnk_devpacks_delete(devpack);
+			kfree(devpack);
+		}
+	}
+}
+
+static int xlnk_buf_findnull(void)
+{
+	int i;
+
+	for (i = 1; i < XLNK_BUF_POOL_SIZE; i++) {
+		if (!xlnk_bufpool[i])
+			return i;
+	}
+
+	return 0;
+}
+
+static int xlnk_buf_find_by_phys_addr(xlnk_intptr_type addr)
+{
+	int i;
+
+	for (i = 1; i < XLNK_BUF_POOL_SIZE; i++) {
+		if (xlnk_bufpool[i] &&
+		    xlnk_phyaddr[i] <= addr &&
+		    xlnk_phyaddr[i] + xlnk_buflen[i] > addr)
+			return i;
+	}
+
+	return 0;
+}
+
+static int xlnk_buf_find_by_user_addr(xlnk_intptr_type addr, int pid)
+{
+	int i;
+
+	for (i = 1; i < XLNK_BUF_POOL_SIZE; i++) {
+		if (xlnk_bufpool[i] &&
+		    xlnk_buf_process[i] == pid &&
+		    xlnk_userbuf[i] <= addr &&
+		    xlnk_userbuf[i] + xlnk_buflen[i] > addr)
+			return i;
+	}
+
+	return 0;
+}
+
+/*
+ * allocate and return an id
+ * id must be a positve number
+ */
+static int xlnk_allocbuf(struct file *filp, unsigned int len,
+			 unsigned int cacheable)
+{
+	int id;
+	void *kaddr;
+	dma_addr_t phys_addr_anchor;
+
+	kaddr = dma_alloc_attrs(xlnk_dev,
+				len,
+				&phys_addr_anchor,
+				GFP_KERNEL | GFP_DMA,
+				0);
+	if (!kaddr)
+		return -ENOMEM;
+
+	spin_lock(&xlnk_buf_lock);
+	id = xlnk_buf_findnull();
+	if (id > 0 && id < XLNK_BUF_POOL_SIZE) {
+		xlnk_bufpool_alloc_point[id] = kaddr;
+		xlnk_bufpool[id] = kaddr;
+		xlnk_buflen[id] = len;
+		xlnk_bufcacheable[id] = cacheable;
+		xlnk_phyaddr[id] = phys_addr_anchor;
+		xlnk_buf_filp[id] = filp;
+	}
+	spin_unlock(&xlnk_buf_lock);
+
+	if (id <= 0 || id >= XLNK_BUF_POOL_SIZE)
+		return -ENOMEM;
+
+	return id;
+}
+
+static u64 dma_mask = 0xFFFFFFFFFFFFFFFFull;
+
+static int xlnk_devregister(char *name,
+			    unsigned int id,
+			    xlnk_intptr_type base,
+			    unsigned int size,
+			    unsigned int *irqs,
+			    xlnk_intptr_type *handle)
+{
+	unsigned int nres;
+	unsigned int nirq;
+	unsigned int *irqptr;
+	struct xlnk_device_pack *devpack;
+	unsigned int i;
+	int status;
+
+	down(&xlnk_devpack_sem);
+	devpack = xlnk_devpacks_find(base);
+	if (devpack) {
+		*handle = (xlnk_intptr_type)devpack;
+		devpack->refs++;
+		status = 0;
+	} else {
+		nirq = 0;
+		irqptr = irqs;
+
+		while (*irqptr) {
+			nirq++;
+			irqptr++;
+		}
+
+		if (nirq > 7) {
+			up(&xlnk_devpack_sem);
+			return -ENOMEM;
+		}
+
+		nres = nirq + 1;
+
+		devpack = xlnk_devpacks_alloc();
+		if (!devpack) {
+			up(&xlnk_devpack_sem);
+			pr_err("Failed to allocate device %s\n", name);
+			return -ENOMEM;
+		}
+		strcpy(devpack->name, name);
+		devpack->pdev.name = devpack->name;
+
+		devpack->pdev.dev.dma_mask = &dma_mask;
+		devpack->pdev.dev.coherent_dma_mask = dma_mask;
+
+		devpack->res[0].start = base;
+		devpack->res[0].end = base + size - 1;
+		devpack->res[0].flags = IORESOURCE_MEM;
+
+		for (i = 0; i < nirq; i++) {
+			devpack->res[i + 1].start = irqs[i];
+			devpack->res[i + 1].end = irqs[i];
+			devpack->res[i + 1].flags = IORESOURCE_IRQ;
+		}
+
+		devpack->pdev.resource = devpack->res;
+		devpack->pdev.num_resources = nres;
+
+		status = platform_device_register(&devpack->pdev);
+		if (status) {
+			xlnk_devpacks_delete(devpack);
+			*handle = 0;
+		} else {
+			*handle = (xlnk_intptr_type)devpack;
+		}
+	}
+	up(&xlnk_devpack_sem);
+
+	return status;
+}
+
+static int xlnk_dmaregister(char *name,
+			    unsigned int id,
+			    xlnk_intptr_type base,
+			    unsigned int size,
+			    unsigned int chan_num,
+			    unsigned int chan0_dir,
+			    unsigned int chan0_irq,
+			    unsigned int chan0_poll_mode,
+			    unsigned int chan0_include_dre,
+			    unsigned int chan0_data_width,
+			    unsigned int chan1_dir,
+			    unsigned int chan1_irq,
+			    unsigned int chan1_poll_mode,
+			    unsigned int chan1_include_dre,
+			    unsigned int chan1_data_width,
+			    xlnk_intptr_type *handle)
+{
+	int status = 0;
+
+#ifdef CONFIG_XILINX_DMA_APF
+
+	struct xlnk_device_pack *devpack;
+
+	if (chan_num < 1 || chan_num > 2) {
+		pr_err("%s: Expected either 1 or 2 channels, got %d\n",
+		       __func__, chan_num);
+		return -EINVAL;
+	}
+
+	down(&xlnk_devpack_sem);
+	devpack = xlnk_devpacks_find(base);
+	if (devpack) {
+		*handle = (xlnk_intptr_type)devpack;
+		devpack->refs++;
+		status = 0;
+	} else {
+		devpack = xlnk_devpacks_alloc();
+		if (!devpack) {
+			up(&xlnk_devpack_sem);
+			return -ENOMEM;
+		}
+		strcpy(devpack->name, name);
+		devpack->pdev.name = "xilinx-axidma";
+
+		devpack->dma_chan_cfg[0].include_dre = chan0_include_dre;
+		devpack->dma_chan_cfg[0].datawidth = chan0_data_width;
+		devpack->dma_chan_cfg[0].irq = chan0_irq;
+		devpack->dma_chan_cfg[0].poll_mode = chan0_poll_mode;
+		devpack->dma_chan_cfg[0].type =
+			(chan0_dir == XLNK_DMA_FROM_DEVICE) ?
+				"axi-dma-s2mm-channel" :
+				"axi-dma-mm2s-channel";
+
+		if (chan_num > 1) {
+			devpack->dma_chan_cfg[1].include_dre =
+				chan1_include_dre;
+			devpack->dma_chan_cfg[1].datawidth = chan1_data_width;
+			devpack->dma_chan_cfg[1].irq = chan1_irq;
+			devpack->dma_chan_cfg[1].poll_mode = chan1_poll_mode;
+			devpack->dma_chan_cfg[1].type =
+				(chan1_dir == XLNK_DMA_FROM_DEVICE) ?
+					"axi-dma-s2mm-channel" :
+					"axi-dma-mm2s-channel";
+		}
+
+		devpack->dma_dev_cfg.name = devpack->name;
+		devpack->dma_dev_cfg.type = "axi-dma";
+		devpack->dma_dev_cfg.include_sg = 1;
+		devpack->dma_dev_cfg.sg_include_stscntrl_strm = 1;
+		devpack->dma_dev_cfg.channel_count = chan_num;
+		devpack->dma_dev_cfg.channel_config = &devpack->dma_chan_cfg[0];
+
+		devpack->pdev.dev.platform_data = &devpack->dma_dev_cfg;
+
+		devpack->pdev.dev.dma_mask = &dma_mask;
+		devpack->pdev.dev.coherent_dma_mask = dma_mask;
+
+		devpack->res[0].start = base;
+		devpack->res[0].end = base + size - 1;
+		devpack->res[0].flags = IORESOURCE_MEM;
+
+		devpack->pdev.resource = devpack->res;
+		devpack->pdev.num_resources = 1;
+		status = platform_device_register(&devpack->pdev);
+		if (status) {
+			xlnk_devpacks_delete(devpack);
+			*handle = 0;
+		} else {
+			*handle = (xlnk_intptr_type)devpack;
+		}
+	}
+	up(&xlnk_devpack_sem);
+
+#endif
+	return status;
+}
+
+static int xlnk_allocbuf_ioctl(struct file *filp,
+			       unsigned int code,
+			       unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	xlnk_int_type id;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	id = xlnk_allocbuf(filp, temp_args.allocbuf.len,
+			   temp_args.allocbuf.cacheable);
+
+	if (id <= 0)
+		return -ENOMEM;
+
+	temp_args.allocbuf.id = id;
+	temp_args.allocbuf.phyaddr = (xlnk_intptr_type)(xlnk_phyaddr[id]);
+	status = copy_to_user((void __user *)args,
+			      &temp_args,
+			      sizeof(union xlnk_args));
+
+	return status;
+}
+
+static int xlnk_freebuf(int id)
+{
+	void *alloc_point;
+	dma_addr_t p_addr;
+	size_t buf_len;
+
+	if (id <= 0 || id >= XLNK_BUF_POOL_SIZE)
+		return -ENOMEM;
+
+	if (!xlnk_bufpool[id])
+		return -ENOMEM;
+
+	spin_lock(&xlnk_buf_lock);
+	alloc_point = xlnk_bufpool_alloc_point[id];
+	p_addr = xlnk_phyaddr[id];
+	buf_len = xlnk_buflen[id];
+	xlnk_bufpool[id] = NULL;
+	xlnk_phyaddr[id] = (dma_addr_t)NULL;
+	xlnk_buflen[id] = 0;
+	xlnk_buf_filp[id] = NULL;
+	xlnk_bufcacheable[id] = 0;
+	spin_unlock(&xlnk_buf_lock);
+
+	dma_free_attrs(xlnk_dev,
+		       buf_len,
+		       alloc_point,
+		       p_addr,
+		       0);
+
+	return 0;
+}
+
+static void xlnk_free_all_buf(void)
+{
+	int i;
+
+	for (i = 1; i < XLNK_BUF_POOL_SIZE; i++)
+		xlnk_freebuf(i);
+}
+
+static int xlnk_freebuf_ioctl(struct file *filp,
+			      unsigned int code,
+			      unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	int id;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	id = temp_args.freebuf.id;
+	return xlnk_freebuf(id);
+}
+
+static int xlnk_adddmabuf_ioctl(struct file *filp,
+				unsigned int code,
+				unsigned long args)
+{
+	union xlnk_args temp_args;
+	struct xlnk_dmabuf_reg *db;
+	int status;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	spin_lock(&xlnk_buf_lock);
+	list_for_each_entry(db, &xlnk_dmabuf_list, list) {
+		if (db->user_vaddr == temp_args.dmasubmit.buf) {
+			pr_err("Attempting to register DMA-BUF for addr %llx that is already registered\n",
+			       (unsigned long long)temp_args.dmabuf.user_addr);
+			spin_unlock(&xlnk_buf_lock);
+			return -EINVAL;
+		}
+	}
+	spin_unlock(&xlnk_buf_lock);
+
+	db = kzalloc(sizeof(*db), GFP_KERNEL);
+	if (!db)
+		return -ENOMEM;
+
+	db->dmabuf_fd = temp_args.dmabuf.dmabuf_fd;
+	db->user_vaddr = temp_args.dmabuf.user_addr;
+	db->dbuf = dma_buf_get(db->dmabuf_fd);
+	db->dbuf_attach = dma_buf_attach(db->dbuf, xlnk_dev);
+	if (IS_ERR(db->dbuf_attach)) {
+		dma_buf_put(db->dbuf);
+		pr_err("Failed DMA-BUF attach\n");
+		return -EINVAL;
+	}
+
+	db->dbuf_sg_table = dma_buf_map_attachment(db->dbuf_attach,
+						   DMA_BIDIRECTIONAL);
+
+	if (!db->dbuf_sg_table) {
+		pr_err("Failed DMA-BUF map_attachment\n");
+		dma_buf_detach(db->dbuf, db->dbuf_attach);
+		dma_buf_put(db->dbuf);
+		return -EINVAL;
+	}
+
+	spin_lock(&xlnk_buf_lock);
+	INIT_LIST_HEAD(&db->list);
+	list_add_tail(&db->list, &xlnk_dmabuf_list);
+	spin_unlock(&xlnk_buf_lock);
+
+	return 0;
+}
+
+static int xlnk_cleardmabuf_ioctl(struct file *filp,
+				  unsigned int code,
+				  unsigned long args)
+{
+	union xlnk_args temp_args;
+	struct xlnk_dmabuf_reg *dp, *dp_temp;
+	int status;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	spin_lock(&xlnk_buf_lock);
+	list_for_each_entry_safe(dp, dp_temp, &xlnk_dmabuf_list, list) {
+		if (dp->user_vaddr == temp_args.dmabuf.user_addr) {
+			dma_buf_unmap_attachment(dp->dbuf_attach,
+						 dp->dbuf_sg_table,
+						 DMA_BIDIRECTIONAL);
+			dma_buf_detach(dp->dbuf, dp->dbuf_attach);
+			dma_buf_put(dp->dbuf);
+			list_del(&dp->list);
+			spin_unlock(&xlnk_buf_lock);
+			kfree(dp);
+			return 0;
+		}
+	}
+	spin_unlock(&xlnk_buf_lock);
+	pr_err("Attempting to unregister a DMA-BUF that was not registered at addr %llx\n",
+	       (unsigned long long)temp_args.dmabuf.user_addr);
+
+	return 1;
+}
+
+static int xlnk_dmarequest_ioctl(struct file *filp, unsigned int code,
+				 unsigned long args)
+{
+#ifdef CONFIG_XILINX_DMA_APF
+	union xlnk_args temp_args;
+	int status;
+	struct xdma_chan *chan;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	if (!temp_args.dmarequest.name[0])
+		return 0;
+
+	down(&xlnk_devpack_sem);
+	chan = xdma_request_channel(temp_args.dmarequest.name);
+	up(&xlnk_devpack_sem);
+	if (!chan)
+		return -ENOMEM;
+	temp_args.dmarequest.dmachan = (xlnk_intptr_type)chan;
+	temp_args.dmarequest.bd_space_phys_addr = chan->bd_phys_addr;
+	temp_args.dmarequest.bd_space_size = chan->bd_chain_size;
+
+	if (copy_to_user((void __user *)args,
+			 &temp_args,
+			 sizeof(union xlnk_args)))
+		return -EFAULT;
+
+	return 0;
+#else
+	return -1;
+#endif
+}
+
+static int xlnk_dmasubmit_ioctl(struct file *filp, unsigned int code,
+				unsigned long args)
+{
+#ifdef CONFIG_XILINX_DMA_APF
+	union xlnk_args temp_args;
+	struct xdma_head *dmahead;
+	struct xlnk_dmabuf_reg *dp, *cp = NULL;
+	int buf_id;
+	void *kaddr = NULL;
+	int status = -1;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	if (!temp_args.dmasubmit.dmachan)
+		return -ENODEV;
+
+	spin_lock(&xlnk_buf_lock);
+	buf_id = xlnk_buf_find_by_phys_addr(temp_args.dmasubmit.buf);
+	if (buf_id) {
+		xlnk_intptr_type addr_delta =
+			temp_args.dmasubmit.buf -
+			xlnk_phyaddr[buf_id];
+		kaddr = (u8 *)(xlnk_bufpool[buf_id]) + addr_delta;
+	} else {
+		list_for_each_entry(dp, &xlnk_dmabuf_list, list) {
+			if (dp->user_vaddr == temp_args.dmasubmit.buf) {
+				cp = dp;
+				break;
+			}
+		}
+	}
+	spin_unlock(&xlnk_buf_lock);
+
+	status = xdma_submit((struct xdma_chan *)
+					(temp_args.dmasubmit.dmachan),
+					temp_args.dmasubmit.buf,
+					kaddr,
+					temp_args.dmasubmit.len,
+					temp_args.dmasubmit.nappwords_i,
+					temp_args.dmasubmit.appwords_i,
+					temp_args.dmasubmit.nappwords_o,
+					temp_args.dmasubmit.flag,
+					&dmahead,
+					cp);
+
+	temp_args.dmasubmit.dmahandle = (xlnk_intptr_type)dmahead;
+	temp_args.dmasubmit.last_bd_index =
+		(xlnk_intptr_type)dmahead->last_bd_index;
+
+	if (!status) {
+		if (copy_to_user((void __user *)args,
+				 &temp_args,
+				 sizeof(union xlnk_args)))
+			return -EFAULT;
+	}
+	return status;
+#else
+	return -ENOMEM;
+#endif
+}
+
+static int xlnk_dmawait_ioctl(struct file *filp,
+			      unsigned int code,
+			      unsigned long args)
+{
+	int status = -1;
+#ifdef CONFIG_XILINX_DMA_APF
+	union xlnk_args temp_args;
+	struct xdma_head *dmahead;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	dmahead = (struct xdma_head *)temp_args.dmawait.dmahandle;
+	status = xdma_wait(dmahead,
+			   dmahead->userflag,
+			   &temp_args.dmawait.flags);
+	if (temp_args.dmawait.flags & XDMA_FLAGS_WAIT_COMPLETE) {
+		if (temp_args.dmawait.nappwords) {
+			memcpy(temp_args.dmawait.appwords,
+			       dmahead->appwords_o,
+			       dmahead->nappwords_o * sizeof(u32));
+		}
+		kfree(dmahead);
+	}
+	if (copy_to_user((void __user *)args,
+			 &temp_args,
+			 sizeof(union xlnk_args)))
+		return -EFAULT;
+#endif
+
+	return status;
+}
+
+static int xlnk_dmarelease_ioctl(struct file *filp, unsigned int code,
+				 unsigned long args)
+{
+	int status = -1;
+#ifdef CONFIG_XILINX_DMA_APF
+	union xlnk_args temp_args;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+	down(&xlnk_devpack_sem);
+	xdma_release_channel((struct xdma_chan *)
+			     (temp_args.dmarelease.dmachan));
+	up(&xlnk_devpack_sem);
+#endif
+
+	return status;
+}
+
+static int xlnk_devregister_ioctl(struct file *filp, unsigned int code,
+				  unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	xlnk_intptr_type handle;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	status = xlnk_devregister(temp_args.devregister.name,
+				  temp_args.devregister.id,
+				  temp_args.devregister.base,
+				  temp_args.devregister.size,
+				  temp_args.devregister.irqs,
+				  &handle);
+
+	return status;
+}
+
+static int xlnk_dmaregister_ioctl(struct file *filp, unsigned int code,
+				  unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	xlnk_intptr_type handle;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	status = xlnk_dmaregister(temp_args.dmaregister.name,
+				  temp_args.dmaregister.id,
+				  temp_args.dmaregister.base,
+				  temp_args.dmaregister.size,
+				  temp_args.dmaregister.chan_num,
+				  temp_args.dmaregister.chan0_dir,
+				  temp_args.dmaregister.chan0_irq,
+				  temp_args.dmaregister.chan0_poll_mode,
+				  temp_args.dmaregister.chan0_include_dre,
+				  temp_args.dmaregister.chan0_data_width,
+				  temp_args.dmaregister.chan1_dir,
+				  temp_args.dmaregister.chan1_irq,
+				  temp_args.dmaregister.chan1_poll_mode,
+				  temp_args.dmaregister.chan1_include_dre,
+				  temp_args.dmaregister.chan1_data_width,
+				  &handle);
+
+	return status;
+}
+
+static int xlnk_devunregister_ioctl(struct file *filp,
+				    unsigned int code,
+				    unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+
+	status = copy_from_user(&temp_args, (void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status)
+		return -ENOMEM;
+
+	xlnk_devpacks_free(temp_args.devunregister.base);
+
+	return 0;
+}
+
+static irqreturn_t xlnk_accel_isr(int irq, void *arg)
+{
+	struct xlnk_irq_control *irq_control = (struct xlnk_irq_control *)arg;
+
+	disable_irq_nosync(irq);
+	complete(&irq_control->cmp);
+
+	return IRQ_HANDLED;
+}
+
+static int xlnk_irq_register_ioctl(struct file *filp, unsigned int code,
+				   unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	int i;
+	struct xlnk_irq_control *ctrl;
+	int irq_id = -1;
+	int irq_entry_new = 0;
+
+	status = copy_from_user(&temp_args,
+				(void __user *)args,
+				sizeof(temp_args.irqregister));
+	if (status)
+		return -ENOMEM;
+
+	if (temp_args.irqregister.type !=
+	    (XLNK_IRQ_LEVEL | XLNK_IRQ_ACTIVE_HIGH)) {
+		dev_err(xlnk_dev, "Unsupported interrupt type %x\n",
+			temp_args.irqregister.type);
+		return -EINVAL;
+	}
+
+	ctrl = kzalloc(sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return -ENOMEM;
+
+	ctrl->irq = xlate_irq(temp_args.irqregister.irq);
+	ctrl->enabled = 0;
+	init_completion(&ctrl->cmp);
+
+	spin_lock(&xlnk_irq_lock);
+	for (i = 0; i < XLNK_IRQ_POOL_SIZE; i++) {
+		if (!xlnk_irq_set[i] && irq_id == -1) {
+			irq_entry_new = 1;
+			irq_id = i;
+			xlnk_irq_set[i] = ctrl;
+		} else if (xlnk_irq_set[i] &&
+			   xlnk_irq_set[i]->irq == ctrl->irq) {
+			irq_id = i;
+			break;
+		}
+	}
+	spin_unlock(&xlnk_irq_lock);
+
+	if (irq_id == -1) {
+		kfree(ctrl);
+		return -ENOMEM;
+	}
+
+	if (!irq_entry_new) {
+		kfree(ctrl);
+	} else {
+		status = request_irq(ctrl->irq,
+				     xlnk_accel_isr,
+				     IRQF_SHARED,
+				     "xlnk",
+				     ctrl);
+		if (status) {
+			enable_irq(ctrl->irq);
+			xlnk_irq_set[irq_id] = NULL;
+			kfree(ctrl);
+			return -EINVAL;
+		}
+		disable_irq_nosync(ctrl->irq);
+	}
+
+	temp_args.irqregister.irq_id = irq_id;
+
+	status = copy_to_user((void __user *)args,
+			      &temp_args,
+			      sizeof(temp_args.irqregister));
+
+	return status;
+}
+
+static int xlnk_irq_unregister_ioctl(struct file *filp, unsigned int code,
+				     unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	int irq_id;
+	struct xlnk_irq_control *ctrl;
+
+	status = copy_from_user(&temp_args,
+				(void __user *)args,
+				sizeof(union xlnk_args));
+	if (status)
+		return -ENOMEM;
+
+	irq_id = temp_args.irqunregister.irq_id;
+	if (irq_id < 0 || irq_id >= XLNK_IRQ_POOL_SIZE)
+		return -EINVAL;
+
+	ctrl = xlnk_irq_set[irq_id];
+	if (!ctrl)
+		return -EINVAL;
+
+	xlnk_irq_set[irq_id] = NULL;
+
+	if (ctrl->enabled) {
+		disable_irq_nosync(ctrl->irq);
+		complete(&ctrl->cmp);
+	}
+	free_irq(ctrl->irq, ctrl);
+	kfree(ctrl);
+
+	return 0;
+}
+
+static int xlnk_irq_wait_ioctl(struct file *filp, unsigned int code,
+			       unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status;
+	int irq_id;
+	struct xlnk_irq_control *ctrl;
+
+	status = copy_from_user(&temp_args,
+				(void __user *)args,
+				sizeof(temp_args.irqwait));
+	if (status)
+		return -ENOMEM;
+
+	irq_id = temp_args.irqwait.irq_id;
+	if (irq_id < 0 || irq_id >= XLNK_IRQ_POOL_SIZE)
+		return -EINVAL;
+
+	ctrl = xlnk_irq_set[irq_id];
+	if (!ctrl)
+		return -EINVAL;
+
+	if (!ctrl->enabled) {
+		ctrl->enabled = 1;
+		enable_irq(ctrl->irq);
+	}
+
+	if (temp_args.irqwait.polling) {
+		if (!try_wait_for_completion(&ctrl->cmp))
+			temp_args.irqwait.success = 0;
+		else
+			temp_args.irqwait.success = 1;
+	} else {
+		wait_for_completion(&ctrl->cmp);
+		temp_args.irqwait.success = 1;
+	}
+
+	if (temp_args.irqwait.success) {
+		reinit_completion(&ctrl->cmp);
+		ctrl->enabled = 0;
+	}
+
+	status = copy_to_user((void __user *)args,
+			      &temp_args,
+			      sizeof(temp_args.irqwait));
+
+	return status;
+}
+
+static int xlnk_cachecontrol_ioctl(struct file *filp, unsigned int code,
+				   unsigned long args)
+{
+	union xlnk_args temp_args;
+	int status, size;
+	void *kaddr;
+	xlnk_intptr_type paddr;
+	int buf_id;
+
+	status = copy_from_user(&temp_args,
+				(void __user *)args,
+				sizeof(union xlnk_args));
+
+	if (status) {
+		dev_err(xlnk_dev, "Error in copy_from_user. status = %d\n",
+			status);
+		return -ENOMEM;
+	}
+
+	if (!(temp_args.cachecontrol.action == 0 ||
+	      temp_args.cachecontrol.action == 1)) {
+		dev_err(xlnk_dev, "Illegal action specified to cachecontrol_ioctl: %d\n",
+			temp_args.cachecontrol.action);
+		return -EINVAL;
+	}
+
+	size = temp_args.cachecontrol.size;
+	paddr = temp_args.cachecontrol.phys_addr;
+
+	spin_lock(&xlnk_buf_lock);
+	buf_id = xlnk_buf_find_by_phys_addr(paddr);
+	kaddr = xlnk_bufpool[buf_id];
+	spin_unlock(&xlnk_buf_lock);
+
+	if (buf_id == 0) {
+		pr_err("Illegal cachecontrol on non-sds_alloc memory");
+		return -EINVAL;
+	}
+
+#if XLNK_SYS_BIT_WIDTH == 32
+	__cpuc_flush_dcache_area(kaddr, size);
+	outer_flush_range(paddr, paddr + size);
+	if (temp_args.cachecontrol.action == 1)
+		outer_inv_range(paddr, paddr + size);
+#else
+	if (temp_args.cachecontrol.action == 1)
+		__dma_map_area(kaddr, size, DMA_FROM_DEVICE);
+	else
+		__dma_map_area(kaddr, size, DMA_TO_DEVICE);
+#endif
+	return 0;
+}
+
+static int xlnk_memop_ioctl(struct file *filp, unsigned long arg_addr)
+{
+	union xlnk_args args;
+	xlnk_intptr_type p_addr = 0;
+	int status = 0;
+	int buf_id;
+	struct xlnk_dmabuf_reg *cp = NULL;
+	int cacheable = 1;
+	enum dma_data_direction dmadir;
+	xlnk_intptr_type page_id;
+	unsigned int page_offset;
+	struct scatterlist sg;
+	unsigned long attrs = 0;
+
+	status = copy_from_user(&args,
+				(void __user *)arg_addr,
+				sizeof(union xlnk_args));
+
+	if (status) {
+		pr_err("Error in copy_from_user.  status = %d\n", status);
+		return status;
+	}
+
+	if (!(args.memop.flags & XLNK_FLAG_MEM_ACQUIRE) &&
+	    !(args.memop.flags & XLNK_FLAG_MEM_RELEASE)) {
+		pr_err("memop lacks acquire or release flag\n");
+		return -EINVAL;
+	}
+
+	if (args.memop.flags & XLNK_FLAG_MEM_ACQUIRE &&
+	    args.memop.flags & XLNK_FLAG_MEM_RELEASE) {
+		pr_err("memop has both acquire and release defined\n");
+		return -EINVAL;
+	}
+
+	spin_lock(&xlnk_buf_lock);
+	buf_id = xlnk_buf_find_by_user_addr(args.memop.virt_addr,
+					    current->pid);
+	if (buf_id > 0) {
+		cacheable = xlnk_bufcacheable[buf_id];
+		p_addr = xlnk_phyaddr[buf_id] +
+			(args.memop.virt_addr - xlnk_userbuf[buf_id]);
+	} else {
+		struct xlnk_dmabuf_reg *dp;
+
+		list_for_each_entry(dp, &xlnk_dmabuf_list, list) {
+			if (dp->user_vaddr == args.memop.virt_addr) {
+				cp = dp;
+				break;
+			}
+		}
+	}
+	spin_unlock(&xlnk_buf_lock);
+
+	if (buf_id <= 0 && !cp) {
+		pr_err("Error, buffer not found\n");
+		return -EINVAL;
+	}
+
+	dmadir = (enum dma_data_direction)args.memop.dir;
+
+	if (args.memop.flags & XLNK_FLAG_COHERENT || !cacheable)
+		attrs |= DMA_ATTR_SKIP_CPU_SYNC;
+
+	if (buf_id > 0) {
+		page_id = p_addr >> PAGE_SHIFT;
+		page_offset = p_addr - (page_id << PAGE_SHIFT);
+		sg_init_table(&sg, 1);
+		sg_set_page(&sg,
+			    pfn_to_page(page_id),
+			    args.memop.size,
+			    page_offset);
+		sg_dma_len(&sg) = args.memop.size;
+	}
+
+	if (args.memop.flags & XLNK_FLAG_MEM_ACQUIRE) {
+		if (buf_id > 0) {
+			status = get_dma_ops(xlnk_dev)->map_sg(xlnk_dev,
+							       &sg,
+							       1,
+							       dmadir,
+							       attrs);
+			if (!status) {
+				pr_err("Failed to map address\n");
+				return -EINVAL;
+			}
+			args.memop.phys_addr = (xlnk_intptr_type)
+				sg_dma_address(&sg);
+			args.memop.token = (xlnk_intptr_type)
+				sg_dma_address(&sg);
+			status = copy_to_user((void __user *)arg_addr,
+					      &args,
+					      sizeof(union xlnk_args));
+			if (status)
+				pr_err("Error in copy_to_user.  status = %d\n",
+				       status);
+		} else {
+			if (cp->dbuf_sg_table->nents != 1) {
+				pr_err("Non-SG-DMA datamovers require physically contiguous DMABUFs.  DMABUF is not physically contiguous\n");
+				return -EINVAL;
+			}
+			args.memop.phys_addr = (xlnk_intptr_type)
+				sg_dma_address(cp->dbuf_sg_table->sgl);
+			args.memop.token = 0;
+			status = copy_to_user((void __user *)arg_addr,
+					      &args,
+					      sizeof(union xlnk_args));
+			if (status)
+				pr_err("Error in copy_to_user.  status = %d\n",
+				       status);
+		}
+	} else {
+		if (buf_id > 0) {
+			sg_dma_address(&sg) = (dma_addr_t)args.memop.token;
+			get_dma_ops(xlnk_dev)->unmap_sg(xlnk_dev,
+							&sg,
+							1,
+							dmadir,
+							attrs);
+		}
+	}
+
+	return status;
+}
+
+static int xlnk_shutdown(unsigned long buf)
+{
+	return 0;
+}
+
+static int xlnk_recover_resource(unsigned long buf)
+{
+	xlnk_free_all_buf();
+#ifdef CONFIG_XILINX_DMA_APF
+	xdma_release_all_channels();
+#endif
+	return 0;
+}
+
+/* This function provides IO interface to the bridge driver. */
+static long xlnk_ioctl(struct file *filp,
+		       unsigned int code,
+		       unsigned long args)
+{
+	if (_IOC_TYPE(code) != XLNK_IOC_MAGIC)
+		return -ENOTTY;
+	if (_IOC_NR(code) > XLNK_IOC_MAXNR)
+		return -ENOTTY;
+
+	/* some sanity check */
+	switch (code) {
+	case XLNK_IOCALLOCBUF:
+		return xlnk_allocbuf_ioctl(filp, code, args);
+	case XLNK_IOCFREEBUF:
+		return xlnk_freebuf_ioctl(filp, code, args);
+	case XLNK_IOCADDDMABUF:
+		return xlnk_adddmabuf_ioctl(filp, code, args);
+	case XLNK_IOCCLEARDMABUF:
+		return xlnk_cleardmabuf_ioctl(filp, code, args);
+	case XLNK_IOCDMAREQUEST:
+		return xlnk_dmarequest_ioctl(filp, code, args);
+	case XLNK_IOCDMASUBMIT:
+		return xlnk_dmasubmit_ioctl(filp, code, args);
+	case XLNK_IOCDMAWAIT:
+		return xlnk_dmawait_ioctl(filp, code, args);
+	case XLNK_IOCDMARELEASE:
+		return xlnk_dmarelease_ioctl(filp, code, args);
+	case XLNK_IOCDEVREGISTER:
+		return xlnk_devregister_ioctl(filp, code, args);
+	case XLNK_IOCDMAREGISTER:
+		return xlnk_dmaregister_ioctl(filp, code, args);
+	case XLNK_IOCDEVUNREGISTER:
+		return xlnk_devunregister_ioctl(filp, code, args);
+	case XLNK_IOCCACHECTRL:
+		return xlnk_cachecontrol_ioctl(filp, code, args);
+	case XLNK_IOCIRQREGISTER:
+		return xlnk_irq_register_ioctl(filp, code, args);
+	case XLNK_IOCIRQUNREGISTER:
+		return xlnk_irq_unregister_ioctl(filp, code, args);
+	case XLNK_IOCIRQWAIT:
+		return xlnk_irq_wait_ioctl(filp, code, args);
+	case XLNK_IOCSHUTDOWN:
+		return xlnk_shutdown(args);
+	case XLNK_IOCRECRES:
+		return xlnk_recover_resource(args);
+	case XLNK_IOCMEMOP:
+		return xlnk_memop_ioctl(filp, args);
+	default:
+		return -EINVAL;
+	}
+}
+
+/* This function maps kernel space memory to user space memory. */
+static int xlnk_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+	int bufid;
+	int status;
+
+	bufid = vma->vm_pgoff >> (16 - PAGE_SHIFT);
+
+	if (bufid == 0) {
+		unsigned long paddr = virt_to_phys(xlnk_dev_buf);
+
+		status = remap_pfn_range(vma,
+					 vma->vm_start,
+					 paddr >> PAGE_SHIFT,
+					 vma->vm_end - vma->vm_start,
+					 vma->vm_page_prot);
+	} else {
+		if (xlnk_bufcacheable[bufid] == 0)
+			vma->vm_page_prot =
+				pgprot_noncached(vma->vm_page_prot);
+		status = remap_pfn_range(vma, vma->vm_start,
+					 xlnk_phyaddr[bufid]
+					 >> PAGE_SHIFT,
+					 vma->vm_end - vma->vm_start,
+					 vma->vm_page_prot);
+		xlnk_userbuf[bufid] = vma->vm_start;
+		xlnk_buf_process[bufid] = current->pid;
+	}
+	if (status) {
+		pr_err("%s failed with code %d\n", __func__, status);
+		return status;
+	}
+
+	vma->vm_private_data = xlnk_bufpool[bufid];
+
+	return 0;
+}
+
+static ssize_t xlnk_write(struct file *filp, const char __user *buf,
+			  size_t count, loff_t *offp)
+{
+	ssize_t retval = 0;
+
+	if (copy_from_user(xlnk_dev_buf + *offp, buf, count)) {
+		retval = -EFAULT;
+		goto out;
+	}
+	*offp += count;
+	retval = count;
+
+	if (xlnk_dev_size < *offp)
+		xlnk_dev_size = *offp;
+
+ out:
+	return retval;
+}
+
+static ssize_t xlnk_read(struct file *filp,
+			 char __user *buf,
+			 size_t count,
+			 loff_t *offp)
+{
+	ssize_t retval = 0;
+
+	if (*offp >= xlnk_dev_size)
+		goto out;
+
+	if (*offp + count > xlnk_dev_size)
+		count = xlnk_dev_size - *offp;
+
+	if (copy_to_user(buf, xlnk_dev_buf + *offp, count)) {
+		retval = -EFAULT;
+		goto out;
+	}
+	*offp += count;
+	retval = count;
+
+ out:
+	return retval;
+}
+
+/*
+ * This function is called when an application closes handle to the bridge
+ * driver.
+ */
+static int xlnk_release(struct inode *ip, struct file *filp)
+{
+	unsigned int i;
+
+	for (i = 1; i < XLNK_BUF_POOL_SIZE; i++) {
+		if (xlnk_buf_filp[i] == filp)
+			xlnk_freebuf(i);
+	}
+
+	return 0;
+}
+
+/*
+ * This function is called when an application opens handle to the
+ * bridge driver.
+ */
+static int xlnk_open(struct inode *ip, struct file *filp)
+{
+	if ((filp->f_flags & O_ACCMODE) == O_WRONLY)
+		xlnk_dev_size = 0;
+
+	return 0;
+}
+
+static const struct file_operations xlnk_fops = {
+	.open = xlnk_open,
+	.release = xlnk_release,
+	.read = xlnk_read,
+	.write = xlnk_write,
+	.unlocked_ioctl = xlnk_ioctl,
+	.mmap = xlnk_mmap,
+};
+
+static int xlnk_remove(struct platform_device *pdev)
+{
+	dev_t devno;
+
+	kfree(xlnk_dev_buf);
+	xlnk_dev_buf = NULL;
+
+	devno = MKDEV(driver_major, 0);
+	cdev_del(&xlnk_cdev);
+	unregister_chrdev_region(devno, 1);
+	if (xlnk_class) {
+		/* remove the device from sysfs */
+		device_destroy(xlnk_class, MKDEV(driver_major, 0));
+		class_destroy(xlnk_class);
+	}
+
+	xlnk_devpacks_free_all();
+
+	return 0;
+}
+
+static int xlnk_init_bufpool(void)
+{
+	unsigned int i;
+
+	spin_lock_init(&xlnk_buf_lock);
+	xlnk_dev_buf = kmalloc(8192, GFP_KERNEL | GFP_DMA);
+	*((char *)xlnk_dev_buf) = '\0';
+
+	if (!xlnk_dev_buf) {
+		dev_err(xlnk_dev, "%s: malloc failed\n", __func__);
+		return -ENOMEM;
+	}
+
+	xlnk_bufpool[0] = xlnk_dev_buf;
+	for (i = 1; i < XLNK_BUF_POOL_SIZE; i++)
+		xlnk_bufpool[i] = NULL;
+
+	return 0;
+}
+
+static void xlnk_init_irqpool(void)
+{
+	int i;
+
+	spin_lock_init(&xlnk_irq_lock);
+	for (i = 0; i < XLNK_IRQ_POOL_SIZE; i++)
+		xlnk_irq_set[i] = NULL;
+}
+
+static int xlnk_probe(struct platform_device *pdev)
+{
+	int err;
+	dev_t dev = 0;
+
+	xlnk_dev_buf = NULL;
+	xlnk_dev_size = 0;
+
+	/* use 2.6 device model */
+	err = alloc_chrdev_region(&dev, 0, 1, DRIVER_NAME);
+	if (err) {
+		dev_err(&pdev->dev, "%s: Can't get major %d\n",
+			__func__, driver_major);
+		goto err1;
+	}
+
+	cdev_init(&xlnk_cdev, &xlnk_fops);
+
+	xlnk_cdev.owner = THIS_MODULE;
+
+	err = cdev_add(&xlnk_cdev, dev, 1);
+
+	if (err) {
+		dev_err(&pdev->dev, "%s: Failed to add XLNK device\n",
+			__func__);
+		goto err3;
+	}
+
+	/* udev support */
+	xlnk_class = class_create(THIS_MODULE, "xlnk");
+	if (IS_ERR(xlnk_class)) {
+		dev_err(xlnk_dev, "%s: Error creating xlnk class\n", __func__);
+		goto err3;
+	}
+
+	driver_major = MAJOR(dev);
+
+	dev_info(&pdev->dev, "Major %d\n", driver_major);
+
+	device_create(xlnk_class, NULL, MKDEV(driver_major, 0),
+		      NULL, "xlnk");
+
+	err = xlnk_init_bufpool();
+	if (err) {
+		dev_err(&pdev->dev, "%s: Failed to allocate buffer pool\n",
+			__func__);
+		goto err3;
+	}
+
+	xlnk_init_irqpool();
+
+	dev_info(&pdev->dev, "%s driver loaded\n", DRIVER_NAME);
+
+	xlnk_pdev = pdev;
+	xlnk_dev = &pdev->dev;
+
+	if (xlnk_pdev)
+		dev_info(&pdev->dev, "xlnk_pdev is not null\n");
+	else
+		dev_info(&pdev->dev, "xlnk_pdev is null\n");
+
+	xlnk_devpacks_init();
+
+	return 0;
+err3:
+	cdev_del(&xlnk_cdev);
+	unregister_chrdev_region(dev, 1);
+err1:
+	return err;
+}
+
+static const struct of_device_id xlnk_match[] = {
+	{ .compatible = "xlnx,xlnk-1.0", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, xlnk_match);
+
+static struct platform_driver xlnk_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = xlnk_match,
+	},
+	.probe = xlnk_probe,
+	.remove = xlnk_remove,
+};
+
+module_platform_driver(xlnk_driver);
+
+MODULE_DESCRIPTION("Xilinx APF driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/apf/xlnk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/apf/xlnk.h
@@ -0,0 +1,180 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2010 Xilinx, Inc. All rights reserved.
+ */
+
+#ifndef _XLNK_OS_H
+#define _XLNK_OS_H
+
+#include <linux/stddef.h>
+#include <linux/dmaengine.h>
+#include "xilinx-dma-apf.h"
+#include "xlnk-sysdef.h"
+
+#define XLNK_FLAG_COHERENT		0x00000001
+#define XLNK_FLAG_KERNEL_BUFFER		0x00000002
+#define XLNK_FLAG_DMAPOLLING		0x00000004
+#define XLNK_FLAG_IOMMU_VALID		0x00000008
+#define XLNK_FLAG_PHYSICAL_ADDR		0x00000100
+#define XLNK_FLAG_VIRTUAL_ADDR		0x00000200
+#define XLNK_FLAG_MEM_ACQUIRE		0x00001000
+#define XLNK_FLAG_MEM_RELEASE		0x00002000
+#define CF_FLAG_CACHE_FLUSH_INVALIDATE	0x00000001
+#define CF_FLAG_PHYSICALLY_CONTIGUOUS	0x00000002
+#define CF_FLAG_DMAPOLLING		0x00000004
+#define XLNK_IRQ_LEVEL			0x00000001
+#define XLNK_IRQ_EDGE			0x00000002
+#define XLNK_IRQ_ACTIVE_HIGH		0x00000004
+#define XLNK_IRQ_ACTIVE_LOW		0x00000008
+#define XLNK_IRQ_RESET_REG_VALID	0x00000010
+
+enum xlnk_dma_direction {
+	XLNK_DMA_BI = 0,
+	XLNK_DMA_TO_DEVICE = 1,
+	XLNK_DMA_FROM_DEVICE = 2,
+	XLNK_DMA_NONE = 3,
+};
+
+struct xlnk_dma_transfer_handle {
+	dma_addr_t dma_addr;
+	unsigned long transfer_length;
+	void *kern_addr;
+	unsigned long user_addr;
+	enum dma_data_direction transfer_direction;
+	int sg_effective_length;
+	int flags;
+	struct dma_chan *channel;
+	dma_cookie_t dma_cookie;
+	struct dma_async_tx_descriptor *async_desc;
+	struct completion completion_handle;
+};
+
+struct xlnk_dmabuf_reg {
+	xlnk_int_type dmabuf_fd;
+	xlnk_intptr_type user_vaddr;
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *dbuf_attach;
+	struct sg_table *dbuf_sg_table;
+	int is_mapped;
+	int dma_direction;
+	struct list_head list;
+};
+
+struct xlnk_irq_control {
+	int irq;
+	int enabled;
+	struct completion cmp;
+};
+
+/* CROSSES KERNEL-USER BOUNDARY */
+union xlnk_args {
+	struct __attribute__ ((__packed__)) {
+		xlnk_uint_type len;
+		xlnk_int_type id;
+		xlnk_intptr_type phyaddr;
+		xlnk_byte_type cacheable;
+	} allocbuf;
+	struct __attribute__ ((__packed__)) {
+		xlnk_uint_type id;
+		xlnk_intptr_type buf;
+	} freebuf;
+	struct __attribute__ ((__packed__)) {
+		xlnk_int_type dmabuf_fd;
+		xlnk_intptr_type user_addr;
+	} dmabuf;
+	struct __attribute__ ((__packed__)) {
+		xlnk_char_type name[64];
+		xlnk_intptr_type dmachan;
+		xlnk_uint_type bd_space_phys_addr;
+		xlnk_uint_type bd_space_size;
+	} dmarequest;
+#define XLNK_MAX_APPWORDS 5
+	struct __attribute__ ((__packed__)) {
+		xlnk_intptr_type dmachan;
+		xlnk_intptr_type buf;
+		xlnk_intptr_type buf2;
+		xlnk_uint_type buf_offset;
+		xlnk_uint_type len;
+		xlnk_uint_type bufflag;
+		xlnk_intptr_type sglist;
+		xlnk_uint_type sgcnt;
+		xlnk_enum_type dmadir;
+		xlnk_uint_type nappwords_i;
+		xlnk_uint_type appwords_i[XLNK_MAX_APPWORDS];
+		xlnk_uint_type nappwords_o;
+		xlnk_uint_type flag;
+		xlnk_intptr_type dmahandle; /* return value */
+		xlnk_uint_type last_bd_index;
+	} dmasubmit;
+	struct __attribute__ ((__packed__)) {
+		xlnk_intptr_type dmahandle;
+		xlnk_uint_type nappwords;
+		xlnk_uint_type appwords[XLNK_MAX_APPWORDS];
+		/* appwords array we only accept 5 max */
+		xlnk_uint_type flags;
+	} dmawait;
+	struct __attribute__ ((__packed__)) {
+		xlnk_intptr_type dmachan;
+	} dmarelease;
+	struct __attribute__ ((__packed__))  {
+		xlnk_intptr_type base;
+		xlnk_uint_type size;
+		xlnk_uint_type irqs[8];
+		xlnk_char_type name[32];
+		xlnk_uint_type id;
+	} devregister;
+	struct __attribute__ ((__packed__)) {
+		xlnk_intptr_type base;
+	} devunregister;
+	struct __attribute__ ((__packed__)) {
+		xlnk_char_type name[32];
+		xlnk_uint_type id;
+		xlnk_intptr_type base;
+		xlnk_uint_type size;
+		xlnk_uint_type chan_num;
+		xlnk_uint_type chan0_dir;
+		xlnk_uint_type chan0_irq;
+		xlnk_uint_type chan0_poll_mode;
+		xlnk_uint_type chan0_include_dre;
+		xlnk_uint_type chan0_data_width;
+		xlnk_uint_type chan1_dir;
+		xlnk_uint_type chan1_irq;
+		xlnk_uint_type chan1_poll_mode;
+		xlnk_uint_type chan1_include_dre;
+		xlnk_uint_type chan1_data_width;
+	} dmaregister;
+	struct __attribute__ ((__packed__)) {
+		xlnk_intptr_type phys_addr;
+		xlnk_uint_type size;
+		xlnk_int_type action;
+	} cachecontrol;
+	struct __attribute__ ((__packed__)) {
+		xlnk_intptr_type virt_addr;
+		xlnk_int_type size;
+		xlnk_enum_type dir;
+		xlnk_int_type flags;
+		xlnk_intptr_type phys_addr;
+		xlnk_intptr_type token;
+	} memop;
+	struct __attribute__ ((__packed__)) {
+		xlnk_int_type irq;
+		xlnk_int_type subirq;
+		xlnk_uint_type type;
+		xlnk_intptr_type control_base;
+		xlnk_intptr_type reset_reg_base;
+		xlnk_uint_type reset_offset;
+		xlnk_uint_type reset_valid_high;
+		xlnk_uint_type reset_valid_low;
+		xlnk_int_type irq_id;
+	} irqregister;
+	struct __attribute__ ((__packed__)) {
+		xlnk_int_type irq_id;
+	} irqunregister;
+	struct __attribute__ ((__packed__)) {
+		xlnk_int_type irq_id;
+		xlnk_int_type polling;
+		xlnk_int_type success;
+	} irqwait;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/emxx_udc/emxx_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/emxx_udc/emxx_udc.c
@@ -2590,10 +2590,15 @@
 		req->unaligned = false;
 
 	if (req->unaligned) {
-		if (!ep->virt_buf)
+		if (!ep->virt_buf) {
 			ep->virt_buf = dma_alloc_coherent(udc->dev, PAGE_SIZE,
 							  &ep->phys_buf,
 							  GFP_ATOMIC | GFP_DMA);
+			if (!ep->virt_buf) {
+				spin_unlock_irqrestore(&udc->lock, flags);
+				return -ENOMEM;
+			}
+		}
 		if (ep->epnum > 0)  {
 			if (ep->direct == USB_DIR_IN)
 				memcpy(ep->virt_buf, req->req.buf,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fbtft/fb_ssd1351.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fbtft/fb_ssd1351.c
@@ -187,7 +187,6 @@
 	},
 };
 
-#ifdef CONFIG_FB_BACKLIGHT
 static int update_onboard_backlight(struct backlight_device *bd)
 {
 	struct fbtft_par *par = bl_get_data(bd);
@@ -231,9 +230,6 @@
 	if (!par->fbtftops.unregister_backlight)
 		par->fbtftops.unregister_backlight = fbtft_unregister_backlight;
 }
-#else
-static void register_onboard_backlight(struct fbtft_par *par) { };
-#endif
 
 FBTFT_REGISTER_DRIVER(DRVNAME, "solomon,ssd1351", &display);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fbtft/fb_st7789v.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fbtft/fb_st7789v.c
@@ -144,6 +144,8 @@
 {
 	int rc;
 
+	par->fbtftops.reset(par);
+
 	rc = init_tearing_effect_line(par);
 	if (rc)
 		return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fbtft/fbtft-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fbtft/fbtft-core.c
@@ -128,7 +128,6 @@
 	return 0;
 }
 
-#ifdef CONFIG_FB_BACKLIGHT
 static int fbtft_backlight_update_status(struct backlight_device *bd)
 {
 	struct fbtft_par *par = bl_get_data(bd);
@@ -161,6 +160,7 @@
 		par->info->bl_dev = NULL;
 	}
 }
+EXPORT_SYMBOL(fbtft_unregister_backlight);
 
 static const struct backlight_ops fbtft_bl_ops = {
 	.get_brightness	= fbtft_backlight_get_brightness,
@@ -198,12 +198,7 @@
 	if (!par->fbtftops.unregister_backlight)
 		par->fbtftops.unregister_backlight = fbtft_unregister_backlight;
 }
-#else
-void fbtft_register_backlight(struct fbtft_par *par) { };
-void fbtft_unregister_backlight(struct fbtft_par *par) { };
-#endif
 EXPORT_SYMBOL(fbtft_register_backlight);
-EXPORT_SYMBOL(fbtft_unregister_backlight);
 
 static void fbtft_set_addr_win(struct fbtft_par *par, int xs, int ys, int xe,
 			       int ye)
@@ -327,11 +322,11 @@
 	schedule_delayed_work(&info->deferred_work, fbdefio->delay);
 }
 
-static void fbtft_deferred_io(struct fb_info *info, struct list_head *pagelist)
+static void fbtft_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	struct fbtft_par *par = info->par;
 	unsigned int dirty_lines_start, dirty_lines_end;
-	struct page *page;
+	struct fb_deferred_io_pageref *pageref;
 	unsigned long index;
 	unsigned int y_low = 0, y_high = 0;
 	int count = 0;
@@ -345,7 +340,8 @@
 	spin_unlock(&par->dirty_lock);
 
 	/* Mark display lines as dirty */
-	list_for_each_entry(page, pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *page = pageref->page;
 		count++;
 		index = page->index << PAGE_SHIFT;
 		y_low = index / info->fix.line_length;
@@ -658,9 +654,9 @@
 	fbops->fb_setcolreg =      fbtft_fb_setcolreg;
 	fbops->fb_blank     =      fbtft_fb_blank;
 
-	fbdefio->delay =           HZ / fps;
-	fbdefio->deferred_io =     fbtft_deferred_io;
-	fb_deferred_io_init(info);
+	fbdefio->delay =            HZ / fps;
+	fbdefio->sort_pagereflist = true;
+	fbdefio->deferred_io =      fbtft_deferred_io;
 
 	snprintf(info->fix.id, sizeof(info->fix.id), "%s", dev->driver->name);
 	info->fix.type =           FB_TYPE_PACKED_PIXELS;
@@ -671,6 +667,7 @@
 	info->fix.line_length =    width * bpp / 8;
 	info->fix.accel =          FB_ACCEL_NONE;
 	info->fix.smem_len =       vmem_size;
+	fb_deferred_io_init(info);
 
 	info->var.rotate =         pdata->rotate;
 	info->var.xres =           width;
@@ -853,13 +850,11 @@
 		 fb_info->fix.smem_len >> 10, text1,
 		 HZ / fb_info->fbdefio->delay, text2);
 
-#ifdef CONFIG_FB_BACKLIGHT
 	/* Turn on backlight if available */
 	if (fb_info->bl_dev) {
 		fb_info->bl_dev->props.power = FB_BLANK_UNBLANK;
 		fb_info->bl_dev->ops->update_status(fb_info->bl_dev);
 	}
-#endif
 
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fbtft/fbtft.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fbtft/fbtft.h
@@ -332,7 +332,10 @@
 	ret = spi_register_driver(&fbtft_driver_spi_driver);               \
 	if (ret < 0)                                                       \
 		return ret;                                                \
-	return platform_driver_register(&fbtft_driver_platform_driver);    \
+	ret = platform_driver_register(&fbtft_driver_platform_driver);     \
+	if (ret < 0)                                                       \
+		spi_unregister_driver(&fbtft_driver_spi_driver);           \
+	return ret;                                                        \
 }                                                                          \
 									   \
 static void __exit fbtft_driver_module_exit(void)                          \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fclk/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fclk/Kconfig
@@ -0,0 +1,9 @@
+#
+# Xilinx PL clk enabler
+#
+
+config XILINX_FCLK
+	tristate "Xilinx PL clock enabler"
+	depends on COMMON_CLK && OF
+	help
+	  Support for the Xilinx fclk clock enabler.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fclk/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fclk/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_XILINX_FCLK)	+= xilinx_fclk.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fclk/TODO
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fclk/TODO
@@ -0,0 +1,2 @@
+TODO:
+	- Remove this hack and clock adapt all the drivers.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fclk/dt-binding.txt
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fclk/dt-binding.txt
@@ -0,0 +1,16 @@
+Binding for Xilinx pl clocks
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+ - compatible: Must be 'xlnx,fclk'
+ - clocks: Handle to input clock
+
+Example:
+	fclk3: fclk3 {
+		status = "disabled";
+		compatible = "xlnx,fclk";
+		clocks = <&clkc 71>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fclk/xilinx_fclk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fclk/xilinx_fclk.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx fclk clock driver.
+ * Copyright (c) 2017 - 2020 Xilinx Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+struct fclk_state {
+	struct device	*dev;
+	struct clk	*pl;
+};
+
+/* Match table for of_platform binding */
+static const struct of_device_id fclk_of_match[] = {
+	{ .compatible = "xlnx,fclk",},
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, fclk_of_match);
+
+static ssize_t set_rate_show(struct device *dev,
+			     struct device_attribute *attr, char *buf)
+{
+	struct fclk_state *st = dev_get_drvdata(dev);
+
+	return scnprintf(buf, PAGE_SIZE, "%lu\n", clk_get_rate(st->pl));
+}
+
+static ssize_t set_rate_store(struct device *dev,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	int ret = 0;
+	unsigned long rate;
+	struct fclk_state *st = dev_get_drvdata(dev);
+
+	ret = kstrtoul(buf, 0, &rate);
+	if (ret)
+		return -EINVAL;
+
+	rate = clk_round_rate(st->pl, rate);
+	ret = clk_set_rate(st->pl, rate);
+
+	return ret ? ret : count;
+}
+
+static DEVICE_ATTR_RW(set_rate);
+
+static const struct attribute *fclk_ctrl_attrs[] = {
+	&dev_attr_set_rate.attr,
+	NULL,
+};
+
+static const struct attribute_group fclk_ctrl_attr_grp = {
+	.attrs = (struct attribute **)fclk_ctrl_attrs,
+};
+
+static int fclk_probe(struct platform_device *pdev)
+{
+	struct fclk_state *st;
+	int ret;
+	struct device *dev = &pdev->dev;
+
+	st = devm_kzalloc(&pdev->dev, sizeof(*st), GFP_KERNEL);
+	if (!st)
+		return -ENOMEM;
+
+	st->dev = dev;
+	platform_set_drvdata(pdev, st);
+
+	st->pl = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(st->pl))
+		return PTR_ERR(st->pl);
+
+	ret = clk_prepare_enable(st->pl);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return ret;
+	}
+
+	ret = sysfs_create_group(&dev->kobj, &fclk_ctrl_attr_grp);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int fclk_remove(struct platform_device *pdev)
+{
+	struct fclk_state *st = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(st->pl);
+	return 0;
+}
+
+static struct platform_driver fclk_driver = {
+	.driver = {
+		.name = KBUILD_MODNAME,
+		.of_match_table = fclk_of_match,
+	},
+	.probe		= fclk_probe,
+	.remove		= fclk_remove,
+};
+
+module_platform_driver(fclk_driver);
+
+MODULE_AUTHOR("Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>");
+MODULE_DESCRIPTION("fclk enable");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/fieldbus/anybuss/host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/fieldbus/anybuss/host.c
@@ -1384,7 +1384,7 @@
 		goto err_device;
 	return cd;
 err_device:
-	device_unregister(&cd->client->dev);
+	put_device(&cd->client->dev);
 err_kthread:
 	kthread_stop(cd->qthread);
 err_reset:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/gdm724x/gdm_lte.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/gdm724x/gdm_lte.c
@@ -76,14 +76,15 @@
 
 static int gdm_lte_rx(struct sk_buff *skb, struct nic *nic, int nic_type)
 {
-	int ret;
+	int ret, len;
 
+	len = skb->len + ETH_HLEN;
 	ret = netif_rx_ni(skb);
 	if (ret == NET_RX_DROP) {
 		nic->stats.rx_dropped++;
 	} else {
 		nic->stats.rx_packets++;
-		nic->stats.rx_bytes += skb->len + ETH_HLEN;
+		nic->stats.rx_bytes += len;
 	}
 
 	return 0;
@@ -349,7 +350,7 @@
 	/* Get ethernet protocol */
 	eth = (struct ethhdr *)skb->data;
 	if (ntohs(eth->h_proto) == ETH_P_8021Q) {
-		vlan_eth = (struct vlan_ethhdr *)skb->data;
+		vlan_eth = skb_vlan_eth_hdr(skb);
 		mac_proto = ntohs(vlan_eth->h_vlan_encapsulated_proto);
 		network_data = skb->data + VLAN_ETH_HLEN;
 		nic_type |= NIC_TYPE_F_VLAN;
@@ -435,7 +436,7 @@
 	 * driver based on the NIC mac
 	 */
 	if (nic_type & NIC_TYPE_F_VLAN) {
-		struct vlan_ethhdr *vlan_eth = (struct vlan_ethhdr *)skb->data;
+		struct vlan_ethhdr *vlan_eth = skb_vlan_eth_hdr(skb);
 
 		nic->vlan_id = ntohs(vlan_eth->h_vlan_TCI) & VLAN_VID_MASK;
 		data_buf = skb->data + (VLAN_ETH_HLEN - ETH_HLEN);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/greybus/arche-apb-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/greybus/arche-apb-ctrl.c
@@ -468,6 +468,7 @@
 	{ .compatible = "usbffff,2", },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, arche_apb_ctrl_of_match);
 
 static struct platform_driver arche_apb_ctrl_device_driver = {
 	.probe		= arche_apb_ctrl_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/greybus/arche-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/greybus/arche-platform.c
@@ -620,14 +620,7 @@
 	{ .compatible = "google,arche-platform", },
 	{ },
 };
-
-static const struct of_device_id arche_combined_id[] = {
-	/* Use PID/VID of SVC device */
-	{ .compatible = "google,arche-platform", },
-	{ .compatible = "usbffff,2", },
-	{ },
-};
-MODULE_DEVICE_TABLE(of, arche_combined_id);
+MODULE_DEVICE_TABLE(of, arche_platform_of_match);
 
 static struct platform_driver arche_platform_device_driver = {
 	.probe		= arche_platform_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/greybus/audio_codec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/greybus/audio_codec.c
@@ -599,8 +599,8 @@
 			break;
 	}
 	if (!data) {
-		dev_err(dai->dev, "%s:%s DATA connection missing\n",
-			dai->name, module->name);
+		dev_err(dai->dev, "%s DATA connection missing\n",
+			dai->name);
 		mutex_unlock(&codec->lock);
 		return -ENODEV;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/greybus/audio_helper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/greybus/audio_helper.c
@@ -3,7 +3,6 @@
  * Greybus Audio Sound SoC helper APIs
  */
 
-#include <linux/debugfs.h>
 #include <sound/core.h>
 #include <sound/soc.h>
 #include <sound/soc-dapm.h>
@@ -116,10 +115,6 @@
 {
 	int i;
 	struct snd_soc_dapm_widget *w, *next_w;
-#ifdef CONFIG_DEBUG_FS
-	struct dentry *parent = dapm->debugfs_dapm;
-	struct dentry *debugfs_w = NULL;
-#endif
 
 	mutex_lock(&dapm->card->dapm_mutex);
 	for (i = 0; i < num; i++) {
@@ -139,12 +134,6 @@
 			continue;
 		}
 		widget++;
-#ifdef CONFIG_DEBUG_FS
-		if (!parent)
-			debugfs_w = debugfs_lookup(w->name, parent);
-		debugfs_remove(debugfs_w);
-		debugfs_w = NULL;
-#endif
 		gbaudio_dapm_free_widget(w);
 	}
 	mutex_unlock(&dapm->card->dapm_mutex);
@@ -192,7 +181,11 @@
 				      unsigned int num_controls)
 {
 	struct snd_card *card = component->card->snd_card;
+	int err;
 
-	return gbaudio_remove_controls(card, component->dev, controls,
-				       num_controls, component->name_prefix);
+	down_write(&card->controls_rwsem);
+	err = gbaudio_remove_controls(card, component->dev, controls,
+				      num_controls, component->name_prefix);
+	up_write(&card->controls_rwsem);
+	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/greybus/audio_topology.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/greybus/audio_topology.c
@@ -147,6 +147,9 @@
 
 	items = le32_to_cpu(gbenum->items);
 	strings = devm_kcalloc(gb->dev, items, sizeof(char *), GFP_KERNEL);
+	if (!strings)
+		return NULL;
+
 	data = gbenum->names;
 
 	for (i = 0; i < items; i++) {
@@ -655,6 +658,8 @@
 	/* since count=1, and reg is dummy */
 	gbe->items = le32_to_cpu(gb_enum->items);
 	gbe->texts = gb_generate_enum_strings(gb, gb_enum);
+	if (!gbe->texts)
+		return -ENOMEM;
 
 	/* debug enum info */
 	dev_dbg(gb->dev, "Max:%d, name_length:%d\n", gbe->items,
@@ -862,6 +867,8 @@
 	/* since count=1, and reg is dummy */
 	gbe->items = le32_to_cpu(gb_enum->items);
 	gbe->texts = gb_generate_enum_strings(gb, gb_enum);
+	if (!gbe->texts)
+		return -ENOMEM;
 
 	/* debug enum info */
 	dev_dbg(gb->dev, "Max:%d, name_length:%d\n", gbe->items,
@@ -974,6 +981,44 @@
 	return ret;
 }
 
+static const struct snd_soc_dapm_widget gbaudio_widgets[] = {
+	[snd_soc_dapm_spk]	= SND_SOC_DAPM_SPK(NULL, gbcodec_event_spk),
+	[snd_soc_dapm_hp]	= SND_SOC_DAPM_HP(NULL, gbcodec_event_hp),
+	[snd_soc_dapm_mic]	= SND_SOC_DAPM_MIC(NULL, gbcodec_event_int_mic),
+	[snd_soc_dapm_output]	= SND_SOC_DAPM_OUTPUT(NULL),
+	[snd_soc_dapm_input]	= SND_SOC_DAPM_INPUT(NULL),
+	[snd_soc_dapm_switch]	= SND_SOC_DAPM_SWITCH_E(NULL, SND_SOC_NOPM,
+					0, 0, NULL,
+					gbaudio_widget_event,
+					SND_SOC_DAPM_PRE_PMU |
+					SND_SOC_DAPM_POST_PMD),
+	[snd_soc_dapm_pga]	= SND_SOC_DAPM_PGA_E(NULL, SND_SOC_NOPM,
+					0, 0, NULL, 0,
+					gbaudio_widget_event,
+					SND_SOC_DAPM_PRE_PMU |
+					SND_SOC_DAPM_POST_PMD),
+	[snd_soc_dapm_mixer]	= SND_SOC_DAPM_MIXER_E(NULL, SND_SOC_NOPM,
+					0, 0, NULL, 0,
+					gbaudio_widget_event,
+					SND_SOC_DAPM_PRE_PMU |
+					SND_SOC_DAPM_POST_PMD),
+	[snd_soc_dapm_mux]	= SND_SOC_DAPM_MUX_E(NULL, SND_SOC_NOPM,
+					0, 0, NULL,
+					gbaudio_widget_event,
+					SND_SOC_DAPM_PRE_PMU |
+					SND_SOC_DAPM_POST_PMD),
+	[snd_soc_dapm_aif_in]	= SND_SOC_DAPM_AIF_IN_E(NULL, NULL, 0,
+					SND_SOC_NOPM, 0, 0,
+					gbaudio_widget_event,
+					SND_SOC_DAPM_PRE_PMU |
+					SND_SOC_DAPM_POST_PMD),
+	[snd_soc_dapm_aif_out]	= SND_SOC_DAPM_AIF_OUT_E(NULL, NULL, 0,
+					SND_SOC_NOPM, 0, 0,
+					gbaudio_widget_event,
+					SND_SOC_DAPM_PRE_PMU |
+					SND_SOC_DAPM_POST_PMD),
+};
+
 static int gbaudio_tplg_create_widget(struct gbaudio_module_info *module,
 				      struct snd_soc_dapm_widget *dw,
 				      struct gb_audio_widget *w, int *w_size)
@@ -1034,6 +1079,10 @@
 			csize += le16_to_cpu(gbenum->names_length);
 			control->texts = (const char * const *)
 				gb_generate_enum_strings(module, gbenum);
+			if (!control->texts) {
+				ret = -ENOMEM;
+				goto error;
+			}
 			control->items = le32_to_cpu(gbenum->items);
 		} else {
 			csize = sizeof(struct gb_audio_control);
@@ -1052,77 +1101,37 @@
 
 	switch (w->type) {
 	case snd_soc_dapm_spk:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_SPK(w->name, gbcodec_event_spk);
+		*dw = gbaudio_widgets[w->type];
 		module->op_devices |= GBAUDIO_DEVICE_OUT_SPEAKER;
 		break;
 	case snd_soc_dapm_hp:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_HP(w->name, gbcodec_event_hp);
+		*dw = gbaudio_widgets[w->type];
 		module->op_devices |= (GBAUDIO_DEVICE_OUT_WIRED_HEADSET
 					| GBAUDIO_DEVICE_OUT_WIRED_HEADPHONE);
 		module->ip_devices |= GBAUDIO_DEVICE_IN_WIRED_HEADSET;
 		break;
 	case snd_soc_dapm_mic:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_MIC(w->name, gbcodec_event_int_mic);
+		*dw = gbaudio_widgets[w->type];
 		module->ip_devices |= GBAUDIO_DEVICE_IN_BUILTIN_MIC;
 		break;
 	case snd_soc_dapm_output:
-		*dw = (struct snd_soc_dapm_widget)SND_SOC_DAPM_OUTPUT(w->name);
-		break;
 	case snd_soc_dapm_input:
-		*dw = (struct snd_soc_dapm_widget)SND_SOC_DAPM_INPUT(w->name);
-		break;
 	case snd_soc_dapm_switch:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_SWITCH_E(w->name, SND_SOC_NOPM, 0, 0,
-					      widget_kctls,
-					      gbaudio_widget_event,
-					      SND_SOC_DAPM_PRE_PMU |
-					      SND_SOC_DAPM_POST_PMD);
-		break;
 	case snd_soc_dapm_pga:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_PGA_E(w->name, SND_SOC_NOPM, 0, 0, NULL, 0,
-					   gbaudio_widget_event,
-					   SND_SOC_DAPM_PRE_PMU |
-					   SND_SOC_DAPM_POST_PMD);
-		break;
 	case snd_soc_dapm_mixer:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_MIXER_E(w->name, SND_SOC_NOPM, 0, 0, NULL,
-					     0, gbaudio_widget_event,
-					     SND_SOC_DAPM_PRE_PMU |
-					     SND_SOC_DAPM_POST_PMD);
-		break;
 	case snd_soc_dapm_mux:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_MUX_E(w->name, SND_SOC_NOPM, 0, 0,
-					   widget_kctls, gbaudio_widget_event,
-					   SND_SOC_DAPM_PRE_PMU |
-					   SND_SOC_DAPM_POST_PMD);
+		*dw = gbaudio_widgets[w->type];
 		break;
 	case snd_soc_dapm_aif_in:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_AIF_IN_E(w->name, w->sname, 0,
-					      SND_SOC_NOPM,
-					      0, 0, gbaudio_widget_event,
-					      SND_SOC_DAPM_PRE_PMU |
-					      SND_SOC_DAPM_POST_PMD);
-		break;
 	case snd_soc_dapm_aif_out:
-		*dw = (struct snd_soc_dapm_widget)
-			SND_SOC_DAPM_AIF_OUT_E(w->name, w->sname, 0,
-					       SND_SOC_NOPM,
-					       0, 0, gbaudio_widget_event,
-					       SND_SOC_DAPM_PRE_PMU |
-					       SND_SOC_DAPM_POST_PMD);
+		*dw = gbaudio_widgets[w->type];
+		dw->sname = w->sname;
 		break;
 	default:
 		ret = -EINVAL;
 		goto error;
 	}
+	dw->name = w->name;
 
 	dev_dbg(module->dev, "%s: widget of type %d created\n", dw->name,
 		dw->id);
@@ -1183,6 +1192,10 @@
 			csize += le16_to_cpu(gbenum->names_length);
 			control->texts = (const char * const *)
 				gb_generate_enum_strings(module, gbenum);
+			if (!control->texts) {
+				ret = -ENOMEM;
+				goto error;
+			}
 			control->items = le32_to_cpu(gbenum->items);
 		} else {
 			csize = sizeof(struct gb_audio_control);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/greybus/light.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/greybus/light.c
@@ -100,15 +100,15 @@
 static struct gb_channel *get_channel_from_mode(struct gb_light *light,
 						u32 mode)
 {
-	struct gb_channel *channel = NULL;
+	struct gb_channel *channel;
 	int i;
 
 	for (i = 0; i < light->channels_count; i++) {
 		channel = &light->channels[i];
-		if (channel && channel->mode == mode)
-			break;
+		if (channel->mode == mode)
+			return channel;
 	}
-	return channel;
+	return NULL;
 }
 
 static int __gb_lights_flash_intensity_set(struct gb_channel *channel,
@@ -147,6 +147,9 @@
 		channel = get_channel_from_mode(channel->light,
 						GB_CHANNEL_MODE_TORCH);
 
+	if (!channel)
+		return -EINVAL;
+
 	/* For not flash we need to convert brightness to intensity */
 	intensity = channel->intensity_uA.min +
 			(channel->intensity_uA.step * channel->led->brightness);
@@ -549,7 +552,10 @@
 	}
 
 	channel_flash = get_channel_from_mode(light, GB_CHANNEL_MODE_FLASH);
-	WARN_ON(!channel_flash);
+	if (!channel_flash) {
+		dev_err(dev, "failed to get flash channel from mode\n");
+		return -EINVAL;
+	}
 
 	fled = &channel_flash->fled;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/accel/adis16203.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/accel/adis16203.c
@@ -312,3 +312,4 @@
 MODULE_DESCRIPTION("Analog Devices ADIS16203 Programmable 360 Degrees Inclinometer");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("spi:adis16203");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/accel/adis16240.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/accel/adis16240.c
@@ -440,3 +440,4 @@
 MODULE_DESCRIPTION("Analog Devices Programmable Impact Sensor and Recorder");
 MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("spi:adis16240");
+MODULE_IMPORT_NS(IIO_ADISLIB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/adc/ad7280a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/adc/ad7280a.c
@@ -107,9 +107,9 @@
 static unsigned int ad7280a_devaddr(unsigned int addr)
 {
 	return ((addr & 0x1) << 4) |
-	       ((addr & 0x2) << 3) |
+	       ((addr & 0x2) << 2) |
 	       (addr & 0x4) |
-	       ((addr & 0x8) >> 3) |
+	       ((addr & 0x8) >> 2) |
 	       ((addr & 0x10) >> 4);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/frequency/ad9832.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/frequency/ad9832.c
@@ -129,12 +129,15 @@
 static int ad9832_write_frequency(struct ad9832_state *st,
 				  unsigned int addr, unsigned long fout)
 {
+	unsigned long clk_freq;
 	unsigned long regval;
 
-	if (fout > (clk_get_rate(st->mclk) / 2))
+	clk_freq = clk_get_rate(st->mclk);
+
+	if (!clk_freq || fout > (clk_freq / 2))
 		return -EINVAL;
 
-	regval = ad9832_calc_freqreg(clk_get_rate(st->mclk), fout);
+	regval = ad9832_calc_freqreg(clk_freq, fout);
 
 	st->freq_data[0] = cpu_to_be16((AD9832_CMD_FRE8BITSW << CMD_SHIFT) |
 					(addr << ADD_SHIFT) |
@@ -155,7 +158,7 @@
 static int ad9832_write_phase(struct ad9832_state *st,
 			      unsigned long addr, unsigned long phase)
 {
-	if (phase > BIT(AD9832_PHASE_BITS))
+	if (phase >= BIT(AD9832_PHASE_BITS))
 		return -EINVAL;
 
 	st->phase_data[0] = cpu_to_be16((AD9832_CMD_PHA8BITSW << CMD_SHIFT) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/frequency/ad9834.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/frequency/ad9834.c
@@ -114,7 +114,7 @@
 
 	clk_freq = clk_get_rate(st->mclk);
 
-	if (fout > (clk_freq / 2))
+	if (!clk_freq || fout > (clk_freq / 2))
 		return -EINVAL;
 
 	regval = ad9834_calc_freqreg(clk_freq, fout);
@@ -131,7 +131,7 @@
 static int ad9834_write_phase(struct ad9834_state *st,
 			      unsigned long addr, unsigned long phase)
 {
-	if (phase > BIT(AD9834_PHASE_BITS))
+	if (phase >= BIT(AD9834_PHASE_BITS))
 		return -EINVAL;
 	st->data = cpu_to_be16(addr | phase);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/impedance-analyzer/ad5933.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/impedance-analyzer/ad5933.c
@@ -608,7 +608,7 @@
 		struct ad5933_state, work.work);
 	struct iio_dev *indio_dev = i2c_get_clientdata(st->client);
 	__be16 buf[2];
-	int val[2];
+	u16 val[2];
 	unsigned char status;
 	int ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/iio/resolver/ad2s1210.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/iio/resolver/ad2s1210.c
@@ -101,7 +101,7 @@
 static const int ad2s1210_mode_vals[4][2] = {
 	[MOD_POS] = { 0, 0 },
 	[MOD_VEL] = { 0, 1 },
-	[MOD_CONFIG] = { 1, 0 },
+	[MOD_CONFIG] = { 1, 1 },
 };
 
 static inline void ad2s1210_set_mode(enum ad2s1210_mode mode,
@@ -658,9 +658,6 @@
 	if (!indio_dev)
 		return -ENOMEM;
 	st = iio_priv(indio_dev);
-	ret = ad2s1210_setup_gpios(st);
-	if (ret < 0)
-		return ret;
 
 	spi_set_drvdata(spi, indio_dev);
 
@@ -671,6 +668,10 @@
 	st->resolution = 12;
 	st->fexcit = AD2S1210_DEF_EXCIT;
 
+	ret = ad2s1210_setup_gpios(st);
+	if (ret < 0)
+		return ret;
+
 	indio_dev->info = &ad2s1210_info;
 	indio_dev->modes = INDIO_DIRECT_MODE;
 	indio_dev->channels = ad2s1210_channels;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/ks7010/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/ks7010/Kconfig
@@ -5,6 +5,9 @@
 	select WIRELESS_EXT
 	select WEXT_PRIV
 	select FW_LOADER
+	select CRYPTO
+	select CRYPTO_HASH
+	select CRYPTO_MICHAEL_MIC
 	help
 	  This is a driver for KeyStream KS7010 based SDIO WIFI cards. It is
 	  found on at least later Spectec SDW-821 (FCC-ID "S2Y-WLAN-11G-K" only,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/ks7010/ks7010_sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/ks7010/ks7010_sdio.c
@@ -395,9 +395,9 @@
 	priv->hostt.buff[priv->hostt.qtail] = le16_to_cpu(hdr->event);
 	priv->hostt.qtail = (priv->hostt.qtail + 1) % SME_EVENT_BUFF_SIZE;
 
-	spin_lock(&priv->tx_dev.tx_dev_lock);
+	spin_lock_bh(&priv->tx_dev.tx_dev_lock);
 	result = enqueue_txdev(priv, p, size, complete_handler, skb);
-	spin_unlock(&priv->tx_dev.tx_dev_lock);
+	spin_unlock_bh(&priv->tx_dev.tx_dev_lock);
 
 	if (txq_has_space(priv))
 		queue_delayed_work(priv->wq, &priv->rw_dwork, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/ks7010/ks_wlan_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/ks7010/ks_wlan_net.c
@@ -1584,8 +1584,10 @@
 			commit |= SME_WEP_FLAG;
 		}
 		if (enc->key_len) {
-			memcpy(&key->key_val[0], &enc->key[0], enc->key_len);
-			key->key_len = enc->key_len;
+			int key_len = clamp_val(enc->key_len, 0, IW_ENCODING_TOKEN_MAX);
+
+			memcpy(&key->key_val[0], &enc->key[0], key_len);
+			key->key_len = key_len;
 			commit |= (SME_WEP_VAL1 << index);
 		}
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/Kconfig
@@ -13,6 +13,7 @@
 	tristate "Intel Atom Image Signal Processor Driver"
 	depends on VIDEO_V4L2 && INTEL_ATOMISP
 	depends on PMIC_OPREGION
+	select V4L2_FWNODE
 	select IOSF_MBI
 	select VIDEOBUF_VMALLOC
 	select VIDEO_V4L2_SUBDEV_API
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/i2c/atomisp-lm3554.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/i2c/atomisp-lm3554.c
@@ -835,7 +835,6 @@
 	int err = 0;
 	struct lm3554 *flash;
 	unsigned int i;
-	int ret;
 
 	flash = kzalloc(sizeof(*flash), GFP_KERNEL);
 	if (!flash)
@@ -844,7 +843,7 @@
 	flash->pdata = lm3554_platform_data_func(client);
 	if (IS_ERR(flash->pdata)) {
 		err = PTR_ERR(flash->pdata);
-		goto fail1;
+		goto free_flash;
 	}
 
 	v4l2_i2c_subdev_init(&flash->sd, client, &lm3554_ops);
@@ -852,12 +851,12 @@
 	flash->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
 	flash->mode = ATOMISP_FLASH_MODE_OFF;
 	flash->timeout = LM3554_MAX_TIMEOUT / LM3554_TIMEOUT_STEPSIZE - 1;
-	ret =
+	err =
 	    v4l2_ctrl_handler_init(&flash->ctrl_handler,
 				   ARRAY_SIZE(lm3554_controls));
-	if (ret) {
+	if (err) {
 		dev_err(&client->dev, "error initialize a ctrl_handler.\n");
-		goto fail3;
+		goto unregister_subdev;
 	}
 
 	for (i = 0; i < ARRAY_SIZE(lm3554_controls); i++)
@@ -866,14 +865,15 @@
 
 	if (flash->ctrl_handler.error) {
 		dev_err(&client->dev, "ctrl_handler error.\n");
-		goto fail3;
+		err = flash->ctrl_handler.error;
+		goto free_handler;
 	}
 
 	flash->sd.ctrl_handler = &flash->ctrl_handler;
 	err = media_entity_pads_init(&flash->sd.entity, 0, NULL);
 	if (err) {
 		dev_err(&client->dev, "error initialize a media entity.\n");
-		goto fail2;
+		goto free_handler;
 	}
 
 	flash->sd.entity.function = MEDIA_ENT_F_FLASH;
@@ -884,16 +884,27 @@
 
 	err = lm3554_gpio_init(client);
 	if (err) {
-		dev_err(&client->dev, "gpio request/direction_output fail");
-		goto fail3;
+		dev_err(&client->dev, "gpio request/direction_output fail.\n");
+		goto cleanup_media;
+	}
+
+	err = atomisp_register_i2c_module(&flash->sd, NULL, LED_FLASH);
+	if (err) {
+		dev_err(&client->dev, "fail to register atomisp i2c module.\n");
+		goto uninit_gpio;
 	}
-	return atomisp_register_i2c_module(&flash->sd, NULL, LED_FLASH);
-fail3:
+
+	return 0;
+
+uninit_gpio:
+	lm3554_gpio_uninit(client);
+cleanup_media:
 	media_entity_cleanup(&flash->sd.entity);
+free_handler:
 	v4l2_ctrl_handler_free(&flash->ctrl_handler);
-fail2:
+unregister_subdev:
 	v4l2_device_unregister_subdev(&flash->sd);
-fail1:
+free_flash:
 	kfree(flash);
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/i2c/ov2680.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/i2c/ov2680.h
@@ -289,8 +289,6 @@
  */
 static struct ov2680_reg const ov2680_QCIF_30fps[] = {
 	{0x3086, 0x01},
-	{0x3501, 0x24},
-	{0x3502, 0x40},
 	{0x370a, 0x23},
 	{0x3801, 0xa0},
 	{0x3802, 0x00},
@@ -334,8 +332,6 @@
  */
 static struct ov2680_reg const ov2680_CIF_30fps[] = {
 	{0x3086, 0x01},
-	{0x3501, 0x24},
-	{0x3502, 0x40},
 	{0x370a, 0x23},
 	{0x3801, 0xa0},
 	{0x3802, 0x00},
@@ -377,8 +373,6 @@
  */
 static struct ov2680_reg const ov2680_QVGA_30fps[] = {
 	{0x3086, 0x01},
-	{0x3501, 0x24},
-	{0x3502, 0x40},
 	{0x370a, 0x23},
 	{0x3801, 0xa0},
 	{0x3802, 0x00},
@@ -420,8 +414,6 @@
  */
 static struct ov2680_reg const ov2680_656x496_30fps[] = {
 	{0x3086, 0x01},
-	{0x3501, 0x24},
-	{0x3502, 0x40},
 	{0x370a, 0x23},
 	{0x3801, 0xa0},
 	{0x3802, 0x00},
@@ -463,8 +455,6 @@
  */
 static struct ov2680_reg const ov2680_720x592_30fps[] = {
 	{0x3086, 0x01},
-	{0x3501, 0x26},
-	{0x3502, 0x40},
 	{0x370a, 0x23},
 	{0x3801, 0x00}, // X_ADDR_START;
 	{0x3802, 0x00},
@@ -508,8 +498,6 @@
  */
 static struct ov2680_reg const ov2680_800x600_30fps[] = {
 	{0x3086, 0x01},
-	{0x3501, 0x26},
-	{0x3502, 0x40},
 	{0x370a, 0x23},
 	{0x3801, 0x00},
 	{0x3802, 0x00},
@@ -551,8 +539,6 @@
  */
 static struct ov2680_reg const ov2680_720p_30fps[] = {
 	{0x3086, 0x00},
-	{0x3501, 0x48},
-	{0x3502, 0xe0},
 	{0x370a, 0x21},
 	{0x3801, 0xa0},
 	{0x3802, 0x00},
@@ -594,8 +580,6 @@
  */
 static struct ov2680_reg const ov2680_1296x976_30fps[] = {
 	{0x3086, 0x00},
-	{0x3501, 0x48},
-	{0x3502, 0xe0},
 	{0x370a, 0x21},
 	{0x3801, 0xa0},
 	{0x3802, 0x00},
@@ -637,8 +621,6 @@
  */
 static struct ov2680_reg const ov2680_1456x1096_30fps[] = {
 	{0x3086, 0x00},
-	{0x3501, 0x48},
-	{0x3502, 0xe0},
 	{0x370a, 0x21},
 	{0x3801, 0x90},
 	{0x3802, 0x00},
@@ -682,8 +664,6 @@
 
 static struct ov2680_reg const ov2680_1616x916_30fps[] = {
 	{0x3086, 0x00},
-	{0x3501, 0x48},
-	{0x3502, 0xe0},
 	{0x370a, 0x21},
 	{0x3801, 0x00},
 	{0x3802, 0x00},
@@ -726,8 +706,6 @@
 #if 0
 static struct ov2680_reg const ov2680_1616x1082_30fps[] = {
 	{0x3086, 0x00},
-	{0x3501, 0x48},
-	{0x3502, 0xe0},
 	{0x370a, 0x21},
 	{0x3801, 0x00},
 	{0x3802, 0x00},
@@ -769,8 +747,6 @@
  */
 static struct ov2680_reg const ov2680_1616x1216_30fps[] = {
 	{0x3086, 0x00},
-	{0x3501, 0x48},
-	{0x3502, 0xe0},
 	{0x370a, 0x21},
 	{0x3801, 0x00},
 	{0x3802, 0x00},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_acc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_acc.c
@@ -439,6 +439,18 @@
 	return 0;
 }
 
+static void atomisp_acc_unload_some_extensions(struct atomisp_sub_device *asd,
+					      int i,
+					      struct atomisp_acc_fw *acc_fw)
+{
+	while (--i >= 0) {
+		if (acc_fw->flags & acc_flag_to_pipe[i].flag) {
+			atomisp_css_unload_acc_extension(asd, acc_fw->fw,
+							 acc_flag_to_pipe[i].pipe_id);
+		}
+	}
+}
+
 /*
  * Appends the loaded acceleration binary extensions to the
  * current ISP mode. Must be called just before sh_css_start().
@@ -479,16 +491,20 @@
 								     acc_fw->fw,
 								     acc_flag_to_pipe[i].pipe_id,
 								     acc_fw->type);
-				if (ret)
+				if (ret) {
+					atomisp_acc_unload_some_extensions(asd, i, acc_fw);
 					goto error;
+				}
 
 				ext_loaded = true;
 			}
 		}
 
 		ret = atomisp_css_set_acc_parameters(acc_fw);
-		if (ret < 0)
+		if (ret < 0) {
+			atomisp_acc_unload_some_extensions(asd, i, acc_fw);
 			goto error;
+		}
 	}
 
 	if (!ext_loaded)
@@ -497,6 +513,7 @@
 	ret = atomisp_css_update_stream(asd);
 	if (ret) {
 		dev_err(isp->dev, "%s: update stream failed.\n", __func__);
+		atomisp_acc_unload_extensions(asd);
 		goto error;
 	}
 
@@ -504,13 +521,6 @@
 	return 0;
 
 error:
-	while (--i >= 0) {
-		if (acc_fw->flags & acc_flag_to_pipe[i].flag) {
-			atomisp_css_unload_acc_extension(asd, acc_fw->fw,
-							 acc_flag_to_pipe[i].pipe_id);
-		}
-	}
-
 	list_for_each_entry_continue_reverse(acc_fw, &asd->acc.fw, list) {
 		if (acc_fw->type != ATOMISP_ACC_FW_LOAD_TYPE_OUTPUT &&
 		    acc_fw->type != ATOMISP_ACC_FW_LOAD_TYPE_VIEWFINDER)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_cmd.c
@@ -899,9 +899,9 @@
 	int err;
 	unsigned long irqflags;
 	struct ia_css_frame *frame = NULL;
-	struct atomisp_s3a_buf *s3a_buf = NULL, *_s3a_buf_tmp;
-	struct atomisp_dis_buf *dis_buf = NULL, *_dis_buf_tmp;
-	struct atomisp_metadata_buf *md_buf = NULL, *_md_buf_tmp;
+	struct atomisp_s3a_buf *s3a_buf = NULL, *_s3a_buf_tmp, *s3a_iter;
+	struct atomisp_dis_buf *dis_buf = NULL, *_dis_buf_tmp, *dis_iter;
+	struct atomisp_metadata_buf *md_buf = NULL, *_md_buf_tmp, *md_iter;
 	enum atomisp_metadata_type md_type;
 	struct atomisp_device *isp = asd->isp;
 	struct v4l2_control ctrl;
@@ -940,60 +940,75 @@
 
 	switch (buf_type) {
 	case IA_CSS_BUFFER_TYPE_3A_STATISTICS:
-		list_for_each_entry_safe(s3a_buf, _s3a_buf_tmp,
+		list_for_each_entry_safe(s3a_iter, _s3a_buf_tmp,
 					 &asd->s3a_stats_in_css, list) {
-			if (s3a_buf->s3a_data ==
+			if (s3a_iter->s3a_data ==
 			    buffer.css_buffer.data.stats_3a) {
-				list_del_init(&s3a_buf->list);
-				list_add_tail(&s3a_buf->list,
+				list_del_init(&s3a_iter->list);
+				list_add_tail(&s3a_iter->list,
 					      &asd->s3a_stats_ready);
+				s3a_buf = s3a_iter;
 				break;
 			}
 		}
 
 		asd->s3a_bufs_in_css[css_pipe_id]--;
 		atomisp_3a_stats_ready_event(asd, buffer.css_buffer.exp_id);
-		dev_dbg(isp->dev, "%s: s3a stat with exp_id %d is ready\n",
-			__func__, s3a_buf->s3a_data->exp_id);
+		if (s3a_buf)
+			dev_dbg(isp->dev, "%s: s3a stat with exp_id %d is ready\n",
+				__func__, s3a_buf->s3a_data->exp_id);
+		else
+			dev_dbg(isp->dev, "%s: s3a stat is ready with no exp_id found\n",
+				__func__);
 		break;
 	case IA_CSS_BUFFER_TYPE_METADATA:
 		if (error)
 			break;
 
 		md_type = atomisp_get_metadata_type(asd, css_pipe_id);
-		list_for_each_entry_safe(md_buf, _md_buf_tmp,
+		list_for_each_entry_safe(md_iter, _md_buf_tmp,
 					 &asd->metadata_in_css[md_type], list) {
-			if (md_buf->metadata ==
+			if (md_iter->metadata ==
 			    buffer.css_buffer.data.metadata) {
-				list_del_init(&md_buf->list);
-				list_add_tail(&md_buf->list,
+				list_del_init(&md_iter->list);
+				list_add_tail(&md_iter->list,
 					      &asd->metadata_ready[md_type]);
+				md_buf = md_iter;
 				break;
 			}
 		}
 		asd->metadata_bufs_in_css[stream_id][css_pipe_id]--;
 		atomisp_metadata_ready_event(asd, md_type);
-		dev_dbg(isp->dev, "%s: metadata with exp_id %d is ready\n",
-			__func__, md_buf->metadata->exp_id);
+		if (md_buf)
+			dev_dbg(isp->dev, "%s: metadata with exp_id %d is ready\n",
+				__func__, md_buf->metadata->exp_id);
+		else
+			dev_dbg(isp->dev, "%s: metadata is ready with no exp_id found\n",
+				__func__);
 		break;
 	case IA_CSS_BUFFER_TYPE_DIS_STATISTICS:
-		list_for_each_entry_safe(dis_buf, _dis_buf_tmp,
+		list_for_each_entry_safe(dis_iter, _dis_buf_tmp,
 					 &asd->dis_stats_in_css, list) {
-			if (dis_buf->dis_data ==
+			if (dis_iter->dis_data ==
 			    buffer.css_buffer.data.stats_dvs) {
 				spin_lock_irqsave(&asd->dis_stats_lock,
 						  irqflags);
-				list_del_init(&dis_buf->list);
-				list_add(&dis_buf->list, &asd->dis_stats);
+				list_del_init(&dis_iter->list);
+				list_add(&dis_iter->list, &asd->dis_stats);
 				asd->params.dis_proj_data_valid = true;
 				spin_unlock_irqrestore(&asd->dis_stats_lock,
 						       irqflags);
+				dis_buf = dis_iter;
 				break;
 			}
 		}
 		asd->dis_bufs_in_css--;
-		dev_dbg(isp->dev, "%s: dis stat with exp_id %d is ready\n",
-			__func__, dis_buf->dis_data->exp_id);
+		if (dis_buf)
+			dev_dbg(isp->dev, "%s: dis stat with exp_id %d is ready\n",
+				__func__, dis_buf->dis_data->exp_id);
+		else
+			dev_dbg(isp->dev, "%s: dis stat is ready with no exp_id found\n",
+				__func__);
 		break;
 	case IA_CSS_BUFFER_TYPE_VF_OUTPUT_FRAME:
 	case IA_CSS_BUFFER_TYPE_SEC_VF_OUTPUT_FRAME:
@@ -1715,6 +1730,12 @@
 {
 	unsigned long next;
 
+	if (!pipe->asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, pipe->vdev.name);
+		return;
+	}
+
 	if (delay != ATOMISP_WDT_KEEP_CURRENT_DELAY)
 		pipe->wdt_duration = delay;
 
@@ -1777,6 +1798,12 @@
 /* ISP2401 */
 void atomisp_wdt_stop_pipe(struct atomisp_video_pipe *pipe, bool sync)
 {
+	if (!pipe->asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, pipe->vdev.name);
+		return;
+	}
+
 	if (!atomisp_is_wdt_running(pipe))
 		return;
 
@@ -4109,6 +4136,12 @@
 	unsigned long irqflags;
 	bool need_to_enqueue_buffer = false;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, pipe->vdev.name);
+		return;
+	}
+
 	if (atomisp_is_vf_pipe(pipe))
 		return;
 
@@ -4196,6 +4229,12 @@
 	struct atomisp_css_params *css_param = &asd->params.css_param;
 	int ret;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (!asd->stream_env[ATOMISP_INPUT_STREAM_GENERAL].stream) {
 		dev_err(asd->isp->dev, "%s: internal error!\n", __func__);
 		return -EINVAL;
@@ -4857,6 +4896,12 @@
 	int source_pad = atomisp_subdev_source_pad(vdev);
 	int ret;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (!isp->inputs[asd->input_curr].camera)
 		return -EINVAL;
 
@@ -5194,10 +5239,17 @@
 	int (*configure_pp_input)(struct atomisp_sub_device *asd,
 				  unsigned int width, unsigned int height) =
 				      configure_pp_input_nop;
-	u16 stream_index = atomisp_source_pad_to_stream_id(asd, source_pad);
+	u16 stream_index;
 	const struct atomisp_in_fmt_conv *fc;
 	int ret, i;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+	stream_index = atomisp_source_pad_to_stream_id(asd, source_pad);
+
 	v4l2_fh_init(&fh.vfh, vdev);
 
 	isp_sink_crop = atomisp_subdev_get_rect(
@@ -5493,7 +5545,8 @@
 				  unsigned int padding_w, unsigned int padding_h,
 				  unsigned int dvs_env_w, unsigned int dvs_env_h)
 {
-	struct atomisp_sub_device *asd = atomisp_to_video_pipe(vdev)->asd;
+	struct atomisp_video_pipe *pipe = atomisp_to_video_pipe(vdev);
+	struct atomisp_sub_device *asd = pipe->asd;
 	const struct atomisp_format_bridge *format;
 	struct v4l2_subdev_pad_config pad_cfg;
 	struct v4l2_subdev_state pad_state = {
@@ -5504,7 +5557,7 @@
 	};
 	struct v4l2_mbus_framefmt *ffmt = &vformat.format;
 	struct v4l2_mbus_framefmt *req_ffmt;
-	struct atomisp_device *isp = asd->isp;
+	struct atomisp_device *isp;
 	struct atomisp_input_stream_info *stream_info =
 	    (struct atomisp_input_stream_info *)ffmt->reserved;
 	u16 stream_index = ATOMISP_INPUT_STREAM_GENERAL;
@@ -5512,6 +5565,14 @@
 	struct v4l2_subdev_fh fh;
 	int ret;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
+	isp = asd->isp;
+
 	v4l2_fh_init(&fh.vfh, vdev);
 
 	stream_index = atomisp_source_pad_to_stream_id(asd, source_pad);
@@ -5602,6 +5663,12 @@
 	struct v4l2_subdev_fh fh;
 	int ret;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (source_pad >= ATOMISP_SUBDEV_PADS_NUM)
 		return -EINVAL;
 
@@ -6034,6 +6101,12 @@
 	struct v4l2_subdev_fh fh;
 	int ret;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	v4l2_fh_init(&fh.vfh, vdev);
 
 	dev_dbg(isp->dev, "setting fmt %ux%u 0x%x for file inject\n",
@@ -6359,6 +6432,12 @@
 {
 	struct atomisp_sub_device *asd = pipe->asd;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, pipe->vdev.name);
+		return false;
+	}
+
 	if (pipe == &asd->video_out_vf)
 		return true;
 
@@ -6572,6 +6651,12 @@
 {
 	struct atomisp_sub_device *asd = pipe->asd;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, pipe->vdev.name);
+		return -EINVAL;
+	}
+
 	if (ATOMISP_USE_YUVPP(asd)) {
 		return IA_CSS_PIPE_ID_YUVPP;
 	} else if (asd->vfpp->val == ATOMISP_VFPP_DISABLE_SCALER) {
@@ -6609,6 +6694,12 @@
 	struct ia_css_pipe_info p_info;
 	int ret;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (asd->isp->inputs[asd->input_curr].camera_caps->
 	    sensor[asd->sensor_curr].stream_num > 1) {
 		/* External ISP */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_fops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_fops.c
@@ -877,6 +877,11 @@
 	else
 		pipe->users++;
 	rt_mutex_unlock(&isp->mutex);
+
+	/* Ensure that a mode is set */
+	if (asd)
+		v4l2_ctrl_s_ctrl(asd->run_mode, pipe->default_run_mode);
+
 	return 0;
 
 css_error:
@@ -1171,6 +1176,12 @@
 	u32 origin_size, new_size;
 	int ret;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (!(vma->vm_flags & (VM_WRITE | VM_READ)))
 		return -EACCES;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_gmin_platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_gmin_platform.c
@@ -481,7 +481,7 @@
 
 static u8 gmin_get_pmic_id_and_addr(struct device *dev)
 {
-	struct i2c_client *power;
+	struct i2c_client *power = NULL;
 	static u8 pmic_i2c_addr;
 
 	if (pmic_id)
@@ -729,6 +729,21 @@
 	return 0;
 }
 
+/*
+ * Some boards contain a hw-bug where turning eldo2 back on after having turned
+ * it off causes the CPLM3218 ambient-light-sensor on the image-sensor's I2C bus
+ * to crash, hanging the bus. Do not turn eldo2 off on these systems.
+ */
+static const struct dmi_system_id axp_leave_eldo2_on_ids[] = {
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "TrekStor"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "SurfTab duo W1 10.1 (VT4)"),
+		},
+	},
+	{ }
+};
+
 static int axp_v1p8_on(struct device *dev, struct gmin_subdev *gs)
 {
 	int ret;
@@ -763,6 +778,9 @@
 	if (ret)
 		return ret;
 
+	if (dmi_check_system(axp_leave_eldo2_on_ids))
+		return 0;
+
 	ret = axp_regulator_set(dev, gs, gs->eldo2_sel_reg, gs->eldo2_1p8v,
 				ELDO_CTRL_REG, gs->eldo2_ctrl_shift, false);
 	return ret;
@@ -1180,7 +1198,7 @@
 	dev_info(dev, "found _DSM entry for '%s': %s\n", var,
 		 cur->string.pointer);
 	strscpy(out, cur->string.pointer, *out_len);
-	*out_len = strlen(cur->string.pointer);
+	*out_len = strlen(out);
 
 	ACPI_FREE(obj);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_ioctl.c
@@ -646,6 +646,12 @@
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 	struct atomisp_sub_device *asd = atomisp_to_video_pipe(vdev)->asd;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	rt_mutex_lock(&isp->mutex);
 	*input = asd->input_curr;
 	rt_mutex_unlock(&isp->mutex);
@@ -665,6 +671,12 @@
 	struct v4l2_subdev *motor;
 	int ret;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	rt_mutex_lock(&isp->mutex);
 	if (input >= ATOM_ISP_MAX_INPUTS || input >= isp->input_cnt) {
 		dev_dbg(isp->dev, "input_cnt: %d\n", isp->input_cnt);
@@ -761,18 +773,33 @@
 	struct video_device *vdev = video_devdata(file);
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 	struct atomisp_sub_device *asd = atomisp_to_video_pipe(vdev)->asd;
-	struct v4l2_subdev_mbus_code_enum code = { 0 };
+	struct v4l2_subdev_mbus_code_enum code = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
+	struct v4l2_subdev *camera;
 	unsigned int i, fi = 0;
 	int rval;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
+	camera = isp->inputs[asd->input_curr].camera;
+	if(!camera) {
+		dev_err(isp->dev, "%s(): camera is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	rt_mutex_lock(&isp->mutex);
-	rval = v4l2_subdev_call(isp->inputs[asd->input_curr].camera, pad,
-				enum_mbus_code, NULL, &code);
+
+	rval = v4l2_subdev_call(camera, pad, enum_mbus_code, NULL, &code);
 	if (rval == -ENOIOCTLCMD) {
 		dev_warn(isp->dev,
-			 "enum_mbus_code pad op not supported. Please fix your sensor driver!\n");
-		//	rval = v4l2_subdev_call(isp->inputs[asd->input_curr].camera,
-		//				video, enum_mbus_fmt, 0, &code.code);
+			 "enum_mbus_code pad op not supported by %s. Please fix your sensor driver!\n",
+			 camera->name);
 	}
 	rt_mutex_unlock(&isp->mutex);
 
@@ -802,6 +829,8 @@
 		f->pixelformat = format->pixelformat;
 		return 0;
 	}
+	dev_err(isp->dev, "%s(): format for code %x not found.\n",
+		__func__, code.code);
 
 	return -EINVAL;
 }
@@ -834,6 +863,72 @@
 	return 0;
 }
 
+static int atomisp_adjust_fmt(struct v4l2_format *f)
+{
+	const struct atomisp_format_bridge *format_bridge;
+	u32 padded_width;
+
+	format_bridge = atomisp_get_format_bridge(f->fmt.pix.pixelformat);
+
+	padded_width = f->fmt.pix.width + pad_w;
+
+	if (format_bridge->planar) {
+		f->fmt.pix.bytesperline = padded_width;
+		f->fmt.pix.sizeimage = PAGE_ALIGN(f->fmt.pix.height *
+						  DIV_ROUND_UP(format_bridge->depth *
+						  padded_width, 8));
+	} else {
+		f->fmt.pix.bytesperline = DIV_ROUND_UP(format_bridge->depth *
+						      padded_width, 8);
+		f->fmt.pix.sizeimage = PAGE_ALIGN(f->fmt.pix.height * f->fmt.pix.bytesperline);
+	}
+
+	if (f->fmt.pix.field == V4L2_FIELD_ANY)
+		f->fmt.pix.field = V4L2_FIELD_NONE;
+
+	format_bridge = atomisp_get_format_bridge(f->fmt.pix.pixelformat);
+	if (!format_bridge)
+		return -EINVAL;
+
+	/* Currently, raw formats are broken!!! */
+	if (format_bridge->sh_fmt == IA_CSS_FRAME_FORMAT_RAW) {
+		f->fmt.pix.pixelformat = V4L2_PIX_FMT_YUV420;
+
+		format_bridge = atomisp_get_format_bridge(f->fmt.pix.pixelformat);
+		if (!format_bridge)
+			return -EINVAL;
+	}
+
+	padded_width = f->fmt.pix.width + pad_w;
+
+	if (format_bridge->planar) {
+		f->fmt.pix.bytesperline = padded_width;
+		f->fmt.pix.sizeimage = PAGE_ALIGN(f->fmt.pix.height *
+						  DIV_ROUND_UP(format_bridge->depth *
+						  padded_width, 8));
+	} else {
+		f->fmt.pix.bytesperline = DIV_ROUND_UP(format_bridge->depth *
+						      padded_width, 8);
+		f->fmt.pix.sizeimage = PAGE_ALIGN(f->fmt.pix.height * f->fmt.pix.bytesperline);
+	}
+
+	if (f->fmt.pix.field == V4L2_FIELD_ANY)
+		f->fmt.pix.field = V4L2_FIELD_NONE;
+
+	/*
+	 * FIXME: do we need to setup this differently, depending on the
+	 * sensor or the pipeline?
+	 */
+	f->fmt.pix.colorspace = V4L2_COLORSPACE_REC709;
+	f->fmt.pix.ycbcr_enc = V4L2_YCBCR_ENC_709;
+	f->fmt.pix.xfer_func = V4L2_XFER_FUNC_709;
+
+	f->fmt.pix.width -= pad_w;
+	f->fmt.pix.height -= pad_h;
+
+	return 0;
+}
+
 /* This function looks up the closest available resolution. */
 static int atomisp_try_fmt_cap(struct file *file, void *fh,
 			       struct v4l2_format *f)
@@ -845,7 +940,11 @@
 	rt_mutex_lock(&isp->mutex);
 	ret = atomisp_try_fmt(vdev, &f->fmt.pix, NULL);
 	rt_mutex_unlock(&isp->mutex);
-	return ret;
+
+	if (ret)
+		return ret;
+
+	return atomisp_adjust_fmt(f);
 }
 
 static int atomisp_s_fmt_cap(struct file *file, void *fh,
@@ -1024,9 +1123,16 @@
 	struct ia_css_frame *frame;
 	struct videobuf_vmalloc_memory *vm_mem;
 	u16 source_pad = atomisp_subdev_source_pad(vdev);
-	u16 stream_id = atomisp_source_pad_to_stream_id(asd, source_pad);
+	u16 stream_id;
 	int ret = 0, i = 0;
 
+	if (!asd) {
+		dev_err(pipe->isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+	stream_id = atomisp_source_pad_to_stream_id(asd, source_pad);
+
 	if (req->count == 0) {
 		mutex_lock(&pipe->capq.vb_lock);
 		if (!list_empty(&pipe->capq.stream))
@@ -1154,6 +1260,12 @@
 	u32 pgnr;
 	int ret = 0;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	rt_mutex_lock(&isp->mutex);
 	if (isp->isp_fatal_error) {
 		ret = -EIO;
@@ -1389,6 +1501,12 @@
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 	int ret = 0;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	rt_mutex_lock(&isp->mutex);
 
 	if (isp->isp_fatal_error) {
@@ -1640,6 +1758,12 @@
 	int ret = 0;
 	unsigned long irqflags;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	dev_dbg(isp->dev, "Start stream on pad %d for asd%d\n",
 		atomisp_subdev_source_pad(vdev), asd->index);
 
@@ -1901,6 +2025,12 @@
 	unsigned long flags;
 	bool first_streamoff = false;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	dev_dbg(isp->dev, "Stop stream on pad %d for asd%d\n",
 		atomisp_subdev_source_pad(vdev), asd->index);
 
@@ -2150,6 +2280,12 @@
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 	int i, ret = -EINVAL;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	for (i = 0; i < ctrls_num; i++) {
 		if (ci_v4l2_controls[i].id == control->id) {
 			ret = 0;
@@ -2229,6 +2365,12 @@
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 	int i, ret = -EINVAL;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	for (i = 0; i < ctrls_num; i++) {
 		if (ci_v4l2_controls[i].id == control->id) {
 			ret = 0;
@@ -2310,6 +2452,12 @@
 	struct atomisp_sub_device *asd = atomisp_to_video_pipe(vdev)->asd;
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	switch (qc->id) {
 	case V4L2_CID_FOCUS_ABSOLUTE:
 	case V4L2_CID_FOCUS_RELATIVE:
@@ -2355,6 +2503,12 @@
 	int i;
 	int ret = 0;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (!IS_ISP2401)
 		motor = isp->inputs[asd->input_curr].motor;
 	else
@@ -2466,6 +2620,12 @@
 	int i;
 	int ret = 0;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (!IS_ISP2401)
 		motor = isp->inputs[asd->input_curr].motor;
 	else
@@ -2591,6 +2751,12 @@
 	struct atomisp_sub_device *asd = atomisp_to_video_pipe(vdev)->asd;
 	struct atomisp_device *isp = video_get_drvdata(vdev);
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (parm->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) {
 		dev_err(isp->dev, "unsupported v4l2 buf type\n");
 		return -EINVAL;
@@ -2613,6 +2779,12 @@
 	int rval;
 	int fps;
 
+	if (!asd) {
+		dev_err(isp->dev, "%s(): asd is NULL, device is %s\n",
+			__func__, vdev->name);
+		return -EINVAL;
+	}
+
 	if (parm->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) {
 		dev_err(isp->dev, "unsupported v4l2 buf type\n");
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_subdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_subdev.c
@@ -1164,23 +1164,28 @@
 
 	atomisp_init_acc_pipe(asd, &asd->video_acc);
 
-	ret = atomisp_video_init(&asd->video_in, "MEMORY");
+	ret = atomisp_video_init(&asd->video_in, "MEMORY",
+				 ATOMISP_RUN_MODE_SDV);
 	if (ret < 0)
 		return ret;
 
-	ret = atomisp_video_init(&asd->video_out_capture, "CAPTURE");
+	ret = atomisp_video_init(&asd->video_out_capture, "CAPTURE",
+				 ATOMISP_RUN_MODE_STILL_CAPTURE);
 	if (ret < 0)
 		return ret;
 
-	ret = atomisp_video_init(&asd->video_out_vf, "VIEWFINDER");
+	ret = atomisp_video_init(&asd->video_out_vf, "VIEWFINDER",
+				 ATOMISP_RUN_MODE_CONTINUOUS_CAPTURE);
 	if (ret < 0)
 		return ret;
 
-	ret = atomisp_video_init(&asd->video_out_preview, "PREVIEW");
+	ret = atomisp_video_init(&asd->video_out_preview, "PREVIEW",
+				 ATOMISP_RUN_MODE_PREVIEW);
 	if (ret < 0)
 		return ret;
 
-	ret = atomisp_video_init(&asd->video_out_video_capture, "VIDEO");
+	ret = atomisp_video_init(&asd->video_out_video_capture, "VIDEO",
+				 ATOMISP_RUN_MODE_VIDEO);
 	if (ret < 0)
 		return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_subdev.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_subdev.h
@@ -81,6 +81,9 @@
 	/* the link list to store per_frame parameters */
 	struct list_head per_frame_params;
 
+	/* Store here the initial run mode */
+	unsigned int default_run_mode;
+
 	unsigned int buffers_in_css;
 
 	/* irq_lock is used to protect video buffer state change operations and
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_v4l2.c
@@ -447,7 +447,8 @@
 	.dfs_table_size = ARRAY_SIZE(dfs_rules_cht_soc),
 };
 
-int atomisp_video_init(struct atomisp_video_pipe *video, const char *name)
+int atomisp_video_init(struct atomisp_video_pipe *video, const char *name,
+		       unsigned int run_mode)
 {
 	int ret;
 	const char *direction;
@@ -478,6 +479,7 @@
 		 "ATOMISP ISP %s %s", name, direction);
 	video->vdev.release = video_device_release_empty;
 	video_set_drvdata(&video->vdev, video->isp);
+	video->default_run_mode = run_mode;
 
 	return 0;
 }
@@ -711,15 +713,15 @@
 
 	dev_dbg(isp->dev, "IUNIT power-%s.\n", enable ? "on" : "off");
 
-	/*WA:Enable DVFS*/
+	/* WA for P-Unit, if DVFS enabled, ISP timeout observed */
 	if (IS_CHT && enable)
-		punit_ddr_dvfs_enable(true);
+		punit_ddr_dvfs_enable(false);
 
 	/*
 	 * FIXME:WA for ECS28A, with this sleep, CTS
 	 * android.hardware.camera2.cts.CameraDeviceTest#testCameraDeviceAbort
 	 * PASS, no impact on other platforms
-	*/
+	 */
 	if (IS_BYT && enable)
 		msleep(10);
 
@@ -727,7 +729,7 @@
 	iosf_mbi_modify(BT_MBI_UNIT_PMC, MBI_REG_READ, MRFLD_ISPSSPM0,
 			val, MRFLD_ISPSSPM0_ISPSSC_MASK);
 
-	/*WA:Enable DVFS*/
+	/* WA:Enable DVFS */
 	if (IS_CHT && !enable)
 		punit_ddr_dvfs_enable(true);
 
@@ -1182,6 +1184,7 @@
 
 	v4l2_device_unregister(&isp->v4l2_dev);
 	media_device_unregister(&isp->media_dev);
+	media_device_cleanup(&isp->media_dev);
 }
 
 static int atomisp_register_entities(struct atomisp_device *isp)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/atomisp_v4l2.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/atomisp_v4l2.h
@@ -27,7 +27,8 @@
 struct atomisp_device;
 struct firmware;
 
-int atomisp_video_init(struct atomisp_video_pipe *video, const char *name);
+int atomisp_video_init(struct atomisp_video_pipe *video, const char *name,
+		       unsigned int run_mode);
 void atomisp_acc_init(struct atomisp_acc_pipe *video, const char *name);
 void atomisp_video_unregister(struct atomisp_video_pipe *video);
 void atomisp_acc_unregister(struct atomisp_acc_pipe *video);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/hmm/hmm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/hmm/hmm.c
@@ -39,7 +39,7 @@
 struct hmm_bo_device bo_device;
 struct hmm_pool	dynamic_pool;
 struct hmm_pool	reserved_pool;
-static ia_css_ptr dummy_ptr;
+static ia_css_ptr dummy_ptr = mmgr_EXCEPTION;
 static bool hmm_initialized;
 struct _hmm_mem_stat hmm_mem_stat;
 
@@ -209,7 +209,7 @@
 
 void hmm_cleanup(void)
 {
-	if (!dummy_ptr)
+	if (dummy_ptr == mmgr_EXCEPTION)
 		return;
 	sysfs_remove_group(&atomisp_dev->kobj, atomisp_attribute_group);
 
@@ -288,7 +288,8 @@
 
 	dev_dbg(atomisp_dev, "%s: free 0x%08x\n", __func__, virt);
 
-	WARN_ON(!virt);
+	if (WARN_ON(virt == mmgr_EXCEPTION))
+		return;
 
 	bo = hmm_bo_device_search_start(&bo_device, (unsigned int)virt);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/isp/kernels/bh/bh_2/ia_css_bh.host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/isp/kernels/bh/bh_2/ia_css_bh.host.c
@@ -13,7 +13,6 @@
  * more details.
  */
 
-#if !defined(HAS_NO_HMEM)
 
 #include "ia_css_types.h"
 #include "sh_css_internal.h"
@@ -63,4 +62,3 @@
 	    uDIGIT_FITTING(from->ae_y_coef_b, 16, SH_CSS_AE_YCOEF_SHIFT);
 }
 
-#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/isp/kernels/raw_aa_binning/raw_aa_binning_1.0/ia_css_raa.host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/isp/kernels/raw_aa_binning/raw_aa_binning_1.0/ia_css_raa.host.c
@@ -13,7 +13,6 @@
  * more details.
  */
 
-#if !defined(HAS_NO_HMEM)
 
 #include "ia_css_types.h"
 #include "sh_css_internal.h"
@@ -32,4 +31,3 @@
 	(void)from;
 }
 
-#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/isp/kernels/s3a/s3a_1.0/ia_css_s3a.host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/isp/kernels/s3a/s3a_1.0/ia_css_s3a.host.c
@@ -227,10 +227,6 @@
     struct ia_css_3a_statistics *host_stats,
     const struct ia_css_bh_table *hmem_buf)
 {
-#if defined(HAS_NO_HMEM)
-	(void)host_stats;
-	(void)hmem_buf;
-#else
 	struct ia_css_3a_rgby_output	*out_ptr;
 	int			i;
 
@@ -291,7 +287,6 @@
 	out_ptr[0].g -= diff;
 	out_ptr[0].b -= diff;
 	out_ptr[0].y -= diff;
-#endif
 }
 
 void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/runtime/binary/src/binary.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/runtime/binary/src/binary.c
@@ -805,11 +805,7 @@
 	s3a_info->deci_factor_log2  = binary->deci_factor_log2;
 	s3a_info->elem_bit_depth    = SH_CSS_BAYER_BITS;
 	s3a_info->use_dmem          = binary->info->sp.s3a.s3atbl_use_dmem;
-#if defined(HAS_NO_HMEM)
-	s3a_info->has_histogram     = 1;
-#else
 	s3a_info->has_histogram     = 0;
-#endif
 	IA_CSS_LEAVE_ERR_PRIVATE(err);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/sh_css.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/sh_css.c
@@ -522,6 +522,7 @@
 	return bpp;
 }
 
+/* TODO: move define to proper file in tools */
 #define GP_ISEL_TPG_MODE 0x90058
 
 #if !defined(ISP2401)
@@ -573,12 +574,8 @@
 		vblank_cycles = vblank_lines * (width + hblank_cycles);
 		sh_css_sp_configure_sync_gen(width, height, hblank_cycles,
 					     vblank_cycles);
-		if (!IS_ISP2401) {
-			if (pipe->stream->config.mode == IA_CSS_INPUT_MODE_TPG) {
-				/* TODO: move define to proper file in tools */
-				ia_css_device_store_uint32(GP_ISEL_TPG_MODE, 0);
-			}
-		}
+		if (pipe->stream->config.mode == IA_CSS_INPUT_MODE_TPG)
+			ia_css_device_store_uint32(GP_ISEL_TPG_MODE, 0);
 	}
 	ia_css_debug_dtrace(IA_CSS_DEBUG_TRACE_PRIVATE,
 			    "sh_css_config_input_network() leave:\n");
@@ -1009,16 +1006,14 @@
 	 * ia_css_isys_stream_capture_indication() instead of
 	 * ia_css_pipeline_sp_wait_for_isys_stream_N() as isp processing of
 	 * capture takes longer than getting an ISYS frame
-	 *
-	 * Only 2401 relevant ??
 	 */
-#if 0 // FIXME: NOT USED on Yocto Aero
-	isys_stream_descr->polling_mode
-	    = early_polling ? INPUT_SYSTEM_POLL_ON_CAPTURE_REQUEST
-	      : INPUT_SYSTEM_POLL_ON_WAIT_FOR_FRAME;
-	ia_css_debug_dtrace(IA_CSS_DEBUG_TRACE_PRIVATE,
-			    "sh_css_translate_stream_cfg_to_isys_stream_descr() leave:\n");
-#endif
+	if (IS_ISP2401) {
+		isys_stream_descr->polling_mode
+		    = early_polling ? INPUT_SYSTEM_POLL_ON_CAPTURE_REQUEST
+		      : INPUT_SYSTEM_POLL_ON_WAIT_FOR_FRAME;
+		ia_css_debug_dtrace(IA_CSS_DEBUG_TRACE_PRIVATE,
+				    "sh_css_translate_stream_cfg_to_isys_stream_descr() leave:\n");
+	}
 
 	return rc;
 }
@@ -1433,7 +1428,7 @@
 
 	assert(me); /* all callers are in this file and call with non null argument */
 
-	if (!IS_ISP2401) {
+	if (IS_ISP2401) {
 		coord = &me->config.internal_frame_origin_bqs_on_sctbl;
 		params = me->stream->isp_params_configs;
 	}
@@ -5327,6 +5322,7 @@
 						  sizeof(struct ia_css_binary),
 						  GFP_KERNEL);
 		if (!mycs->yuv_scaler_binary) {
+			mycs->num_yuv_scaler = 0;
 			err = -ENOMEM;
 			return err;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/sh_css_frac.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/sh_css_frac.h
@@ -30,12 +30,24 @@
 #define uISP_VAL_MAX		      ((unsigned int)((1 << uISP_REG_BIT) - 1))
 
 /* a:fraction bits for 16bit precision, b:fraction bits for ISP precision */
-#define sDIGIT_FITTING(v, a, b) \
-	min_t(int, max_t(int, (((v) >> sSHIFT) >> max(sFRACTION_BITS_FITTING(a) - (b), 0)), \
-	  sISP_VAL_MIN), sISP_VAL_MAX)
-#define uDIGIT_FITTING(v, a, b) \
-	min((unsigned int)max((unsigned)(((v) >> uSHIFT) \
-	>> max((int)(uFRACTION_BITS_FITTING(a) - (b)), 0)), \
-	  uISP_VAL_MIN), uISP_VAL_MAX)
+static inline int sDIGIT_FITTING(int v, int a, int b)
+{
+	int fit_shift = sFRACTION_BITS_FITTING(a) - b;
+
+	v >>= sSHIFT;
+	v >>= fit_shift > 0 ? fit_shift : 0;
+
+	return clamp_t(int, v, sISP_VAL_MIN, sISP_VAL_MAX);
+}
+
+static inline unsigned int uDIGIT_FITTING(unsigned int v, int a, int b)
+{
+	int fit_shift = uFRACTION_BITS_FITTING(a) - b;
+
+	v >>= uSHIFT;
+	v >>= fit_shift > 0 ? fit_shift : 0;
+
+	return clamp_t(unsigned int, v, uISP_VAL_MIN, uISP_VAL_MAX);
+}
 
 #endif /* __SH_CSS_FRAC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/sh_css_mipi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/sh_css_mipi.c
@@ -374,17 +374,17 @@
 {
 	if (!IS_ISP2401) {
 		if (pipe->stream->config.mode == IA_CSS_INPUT_MODE_BUFFERED_SENSOR)
-			return false;
-		else
 			return true;
+		else
+			return false;
 	}
 
 	if (pipe->stream->config.mode == IA_CSS_INPUT_MODE_BUFFERED_SENSOR ||
 	    pipe->stream->config.mode == IA_CSS_INPUT_MODE_TPG ||
 	    pipe->stream->config.mode == IA_CSS_INPUT_MODE_PRBS)
-		return false;
+		return true;
 
-	return true;
+	return false;
 }
 
 int
@@ -423,14 +423,17 @@
 		return 0; /* AM TODO: Check  */
 	}
 
-	if (!IS_ISP2401)
+	if (!IS_ISP2401) {
 		port = (unsigned int)pipe->stream->config.source.port.port;
-	else
-		err = ia_css_mipi_is_source_port_valid(pipe, &port);
+	} else {
+		/* Returns true if port is valid. So, invert it */
+		err = !ia_css_mipi_is_source_port_valid(pipe, &port);
+	}
 
 	assert(port < N_CSI_PORTS);
 
-	if (port >= N_CSI_PORTS || err) {
+	if ((!IS_ISP2401 && port >= N_CSI_PORTS) ||
+	    (IS_ISP2401 && err)) {
 		ia_css_debug_dtrace(IA_CSS_DEBUG_TRACE_PRIVATE,
 				    "allocate_mipi_frames(%p) exit: error: port is not correct (port=%d).\n",
 				    pipe, port);
@@ -552,14 +555,17 @@
 			return err;
 		}
 
-		if (!IS_ISP2401)
+		if (!IS_ISP2401) {
 			port = (unsigned int)pipe->stream->config.source.port.port;
-		else
-			err = ia_css_mipi_is_source_port_valid(pipe, &port);
+		} else {
+			/* Returns true if port is valid. So, invert it */
+			err = !ia_css_mipi_is_source_port_valid(pipe, &port);
+		}
 
 		assert(port < N_CSI_PORTS);
 
-		if (port >= N_CSI_PORTS || err) {
+		if ((!IS_ISP2401 && port >= N_CSI_PORTS) ||
+		    (IS_ISP2401 && err)) {
 			ia_css_debug_dtrace(IA_CSS_DEBUG_TRACE_PRIVATE,
 					    "free_mipi_frames(%p, %d) exit: error: pipe port is not correct.\n",
 					    pipe, port);
@@ -663,14 +669,17 @@
 		/* TODO: AM: maybe this should be returning an error. */
 	}
 
-	if (!IS_ISP2401)
+	if (!IS_ISP2401) {
 		port = (unsigned int)pipe->stream->config.source.port.port;
-	else
-		err = ia_css_mipi_is_source_port_valid(pipe, &port);
+	} else {
+		/* Returns true if port is valid. So, invert it */
+		err = !ia_css_mipi_is_source_port_valid(pipe, &port);
+	}
 
 	assert(port < N_CSI_PORTS);
 
-	if (port >= N_CSI_PORTS || err) {
+	if ((!IS_ISP2401 && port >= N_CSI_PORTS) ||
+	    (IS_ISP2401 && err)) {
 		IA_CSS_ERROR("send_mipi_frames(%p) exit: invalid port specified (port=%d).\n",
 			     pipe, port);
 		return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/atomisp/pci/sh_css_params.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/atomisp/pci/sh_css_params.c
@@ -16,12 +16,10 @@
 #include "gdc_device.h"		/* gdc_lut_store(), ... */
 #include "isp.h"			/* ISP_VEC_ELEMBITS */
 #include "vamem.h"
-#if !defined(HAS_NO_HMEM)
 #ifndef __INLINE_HMEM__
 #define __INLINE_HMEM__
 #endif
 #include "hmem.h"
-#endif /* !defined(HAS_NO_HMEM) */
 #define IA_CSS_INCLUDE_PARAMETERS
 #define IA_CSS_INCLUDE_ACC_PARAMETERS
 
@@ -962,8 +960,8 @@
 		params->fpn_config.data = NULL;
 	}
 	if (!params->fpn_config.data) {
-		params->fpn_config.data = kvmalloc(height * width *
-						   sizeof(short), GFP_KERNEL);
+		params->fpn_config.data = kvmalloc(array3_size(height, width, sizeof(short)),
+						   GFP_KERNEL);
 		if (!params->fpn_config.data) {
 			IA_CSS_ERROR("out of memory");
 			IA_CSS_LEAVE_ERR_PRIVATE(-ENOMEM);
@@ -1510,10 +1508,8 @@
 		ia_css_s3a_vmem_decode(host_stats, isp_stats->vmem_stats_hi,
 				       isp_stats->vmem_stats_lo);
 	}
-#if !defined(HAS_NO_HMEM)
 	IA_CSS_LOG("3A: HMEM");
 	ia_css_s3a_hmem_decode(host_stats, isp_stats->hmem_stats);
-#endif
 
 	IA_CSS_LEAVE("void");
 }
@@ -2250,9 +2246,7 @@
 		me->vmem_size = ISP_S3ATBL_HI_LO_STRIDE_BYTES *
 				grid->aligned_height;
 	}
-#if !defined(HAS_NO_HMEM)
 	me->hmem_size = sizeof_hmem(HMEM0_ID);
-#endif
 
 	/* All subsections need to be aligned to the system bus width */
 	me->dmem_size = CEIL_MUL(me->dmem_size, HIVE_ISP_DDR_WORD_BYTES);
@@ -2431,7 +2425,7 @@
 	unsigned int i;
 	struct sh_css_ddr_address_map *ddr_ptrs;
 	struct sh_css_ddr_address_map_size *ddr_ptrs_size;
-	int err = 0;
+	int err;
 	size_t params_size;
 	struct ia_css_isp_parameters *params =
 	kvmalloc(sizeof(struct ia_css_isp_parameters), GFP_KERNEL);
@@ -2473,7 +2467,11 @@
 	succ &= (ddr_ptrs->macc_tbl != mmgr_NULL);
 
 	*isp_params_out = params;
-	return err;
+
+	if (!succ)
+		return -ENOMEM;
+
+	return 0;
 }
 
 static bool
@@ -4335,12 +4333,10 @@
 	me->data = kvmalloc(grid_size * sizeof(*me->data), GFP_KERNEL);
 	if (!me->data)
 		goto err;
-#if !defined(HAS_NO_HMEM)
 	/* No weighted histogram, no structure, treat the histogram data as a byte dump in a byte array */
 	me->rgby_data = kvmalloc(sizeof_hmem(HMEM0_ID), GFP_KERNEL);
-#else
-	me->rgby_data = NULL;
-#endif
+	if (!me->rgby_data)
+		goto err;
 
 	IA_CSS_LEAVE("return=%p", me);
 	return me;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/av7110/av7110_av.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/av7110/av7110_av.c
@@ -823,10 +823,10 @@
 		av7110_ipack_flush(ipack);
 
 	if (buf[3] & ADAPT_FIELD) {
+		if (buf[4] > len - 1 - 4)
+			return 0;
 		len -= buf[4] + 1;
 		buf += buf[4] + 1;
-		if (!len)
-			return 0;
 	}
 
 	av7110_ipack_instant_repack(buf + 4, len - 4, ipack);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/av7110/sp8870.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/av7110/sp8870.c
@@ -606,4 +606,4 @@
 MODULE_AUTHOR("Juergen Peitz");
 MODULE_LICENSE("GPL");
 
-EXPORT_SYMBOL(sp8870_attach);
+EXPORT_SYMBOL_GPL(sp8870_attach);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro.h
@@ -262,6 +262,7 @@
  * @max_depth:	Maximum depth, for bitstream formats
  * @enc_fmt:	Format identifier for encoder registers.
  * @frmsize:	Supported range of frame sizes (only for bitstream formats).
+ * @postprocessed: Indicates if this format needs the post-processor.
  */
 struct hantro_fmt {
 	char *name;
@@ -271,6 +272,7 @@
 	int max_depth;
 	enum hantro_enc_fmt enc_fmt;
 	struct v4l2_frmsize_stepwise frmsize;
+	bool postprocessed;
 };
 
 struct hantro_reg {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_drv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_drv.c
@@ -958,7 +958,7 @@
 	ret = clk_bulk_prepare(vpu->variant->num_clocks, vpu->clocks);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to prepare clocks\n");
-		return ret;
+		goto err_pm_disable;
 	}
 
 	ret = v4l2_device_register(&pdev->dev, &vpu->v4l2_dev);
@@ -1014,6 +1014,7 @@
 	v4l2_device_unregister(&vpu->v4l2_dev);
 err_clk_unprepare:
 	clk_bulk_unprepare(vpu->variant->num_clocks, vpu->clocks);
+err_pm_disable:
 	pm_runtime_dont_use_autosuspend(vpu->dev);
 	pm_runtime_disable(vpu->dev);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_g2_hevc_dec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_g2_hevc_dec.c
@@ -74,7 +74,7 @@
 					no_chroma = 1;
 				for (j = 0, tmp_w = 0; j < num_tile_cols - 1; j++) {
 					tmp_w += pps->column_width_minus1[j] + 1;
-					*p++ = pps->column_width_minus1[j + 1];
+					*p++ = pps->column_width_minus1[j] + 1;
 					*p++ = h;
 					if (i == 0 && h == 1 && ctb_size == 16)
 						no_chroma = 1;
@@ -194,13 +194,8 @@
 		hantro_reg_write(vpu, &g2_max_cu_qpd_depth, 0);
 	}
 
-	if (pps->flags & V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT) {
-		hantro_reg_write(vpu, &g2_cb_qp_offset, pps->pps_cb_qp_offset);
-		hantro_reg_write(vpu, &g2_cr_qp_offset, pps->pps_cr_qp_offset);
-	} else {
-		hantro_reg_write(vpu, &g2_cb_qp_offset, 0);
-		hantro_reg_write(vpu, &g2_cr_qp_offset, 0);
-	}
+	hantro_reg_write(vpu, &g2_cb_qp_offset, pps->pps_cb_qp_offset);
+	hantro_reg_write(vpu, &g2_cr_qp_offset, pps->pps_cr_qp_offset);
 
 	hantro_reg_write(vpu, &g2_filt_offset_beta, pps->pps_beta_offset_div2);
 	hantro_reg_write(vpu, &g2_filt_offset_tc, pps->pps_tc_offset_div2);
@@ -269,24 +264,11 @@
 	hantro_reg_write(vpu, &g2_apf_threshold, 8);
 }
 
-static int find_ref_pic_index(const struct v4l2_hevc_dpb_entry *dpb, int pic_order_cnt)
-{
-	int i;
-
-	for (i = 0; i < V4L2_HEVC_DPB_ENTRIES_NUM_MAX; i++) {
-		if (dpb[i].pic_order_cnt[0] == pic_order_cnt)
-			return i;
-	}
-
-	return 0x0;
-}
-
 static void set_ref_pic_list(struct hantro_ctx *ctx)
 {
 	const struct hantro_hevc_dec_ctrls *ctrls = &ctx->hevc_dec.ctrls;
 	struct hantro_dev *vpu = ctx->dev;
 	const struct v4l2_ctrl_hevc_decode_params *decode_params = ctrls->decode_params;
-	const struct v4l2_hevc_dpb_entry *dpb = decode_params->dpb;
 	u32 list0[V4L2_HEVC_DPB_ENTRIES_NUM_MAX] = {};
 	u32 list1[V4L2_HEVC_DPB_ENTRIES_NUM_MAX] = {};
 	static const struct hantro_reg ref_pic_regs0[] = {
@@ -330,11 +312,11 @@
 	/* List 0 contains: short term before, short term after and long term */
 	j = 0;
 	for (i = 0; i < decode_params->num_poc_st_curr_before && j < ARRAY_SIZE(list0); i++)
-		list0[j++] = find_ref_pic_index(dpb, decode_params->poc_st_curr_before[i]);
+		list0[j++] = decode_params->poc_st_curr_before[i];
 	for (i = 0; i < decode_params->num_poc_st_curr_after && j < ARRAY_SIZE(list0); i++)
-		list0[j++] = find_ref_pic_index(dpb, decode_params->poc_st_curr_after[i]);
+		list0[j++] = decode_params->poc_st_curr_after[i];
 	for (i = 0; i < decode_params->num_poc_lt_curr && j < ARRAY_SIZE(list0); i++)
-		list0[j++] = find_ref_pic_index(dpb, decode_params->poc_lt_curr[i]);
+		list0[j++] = decode_params->poc_lt_curr[i];
 
 	/* Fill the list, copying over and over */
 	i = 0;
@@ -343,11 +325,11 @@
 
 	j = 0;
 	for (i = 0; i < decode_params->num_poc_st_curr_after && j < ARRAY_SIZE(list1); i++)
-		list1[j++] = find_ref_pic_index(dpb, decode_params->poc_st_curr_after[i]);
+		list1[j++] = decode_params->poc_st_curr_after[i];
 	for (i = 0; i < decode_params->num_poc_st_curr_before && j < ARRAY_SIZE(list1); i++)
-		list1[j++] = find_ref_pic_index(dpb, decode_params->poc_st_curr_before[i]);
+		list1[j++] = decode_params->poc_st_curr_before[i];
 	for (i = 0; i < decode_params->num_poc_lt_curr && j < ARRAY_SIZE(list1); i++)
-		list1[j++] = find_ref_pic_index(dpb, decode_params->poc_lt_curr[i]);
+		list1[j++] = decode_params->poc_lt_curr[i];
 
 	i = 0;
 	while (j < ARRAY_SIZE(list1))
@@ -431,7 +413,7 @@
 
 	set_ref_pic_list(ctx);
 
-	/* We will only keep the references picture that are still used */
+	/* We will only keep the reference pictures that are still used */
 	ctx->hevc_dec.ref_bufs_used = 0;
 
 	/* Set up addresses of DPB buffers */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_h1_jpeg_enc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_h1_jpeg_enc.c
@@ -23,7 +23,7 @@
 
 	reg = H1_REG_IN_IMG_CTRL_ROW_LEN(pix_fmt->width)
 		| H1_REG_IN_IMG_CTRL_OVRFLR_D4(0)
-		| H1_REG_IN_IMG_CTRL_OVRFLB_D4(0)
+		| H1_REG_IN_IMG_CTRL_OVRFLB(0)
 		| H1_REG_IN_IMG_CTRL_FMT(ctx->vpu_src_fmt->enc_fmt);
 	vepu_write_relaxed(vpu, reg, H1_REG_IN_IMG_CTRL);
 }
@@ -140,7 +140,7 @@
 	return 0;
 }
 
-void hantro_jpeg_enc_done(struct hantro_ctx *ctx)
+void hantro_h1_jpeg_enc_done(struct hantro_ctx *ctx)
 {
 	struct hantro_dev *vpu = ctx->dev;
 	u32 bytesused = vepu_read(vpu, H1_REG_STR_BUF_LIMIT) / 8;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_h1_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_h1_regs.h
@@ -47,7 +47,7 @@
 #define H1_REG_IN_IMG_CTRL				0x03c
 #define     H1_REG_IN_IMG_CTRL_ROW_LEN(x)		((x) << 12)
 #define     H1_REG_IN_IMG_CTRL_OVRFLR_D4(x)		((x) << 10)
-#define     H1_REG_IN_IMG_CTRL_OVRFLB_D4(x)		((x) << 6)
+#define     H1_REG_IN_IMG_CTRL_OVRFLB(x)		((x) << 6)
 #define     H1_REG_IN_IMG_CTRL_FMT(x)			((x) << 2)
 #define H1_REG_ENC_CTRL0				0x040
 #define    H1_REG_ENC_CTRL0_INIT_QP(x)			((x) << 26)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_h264.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_h264.c
@@ -354,8 +354,6 @@
 
 	if (!(dpb->flags & V4L2_H264_DPB_ENTRY_FLAG_ACTIVE))
 		return 0;
-	if (dpb->flags & V4L2_H264_DPB_ENTRY_FLAG_LONG_TERM)
-		return dpb->pic_num;
 	return dpb->frame_num;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_hevc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_hevc.c
@@ -98,7 +98,7 @@
 	struct hantro_hevc_dec_hw_ctx *hevc_dec = &ctx->hevc_dec;
 	int i;
 
-	/* Find the reference buffer in already know ones */
+	/* Find the reference buffer in already known ones */
 	for (i = 0;  i < NUM_REF_PICTURES; i++) {
 		if (hevc_dec->ref_bufs_poc[i] == poc) {
 			hevc_dec->ref_bufs_used |= 1 << i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_hw.h
@@ -235,7 +235,8 @@
 int rockchip_vpu2_jpeg_enc_run(struct hantro_ctx *ctx);
 int hantro_jpeg_enc_init(struct hantro_ctx *ctx);
 void hantro_jpeg_enc_exit(struct hantro_ctx *ctx);
-void hantro_jpeg_enc_done(struct hantro_ctx *ctx);
+void hantro_h1_jpeg_enc_done(struct hantro_ctx *ctx);
+void rockchip_vpu2_jpeg_enc_done(struct hantro_ctx *ctx);
 
 dma_addr_t hantro_h264_get_ref_buf(struct hantro_ctx *ctx,
 				   unsigned int dpb_idx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_postproc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_postproc.c
@@ -53,15 +53,9 @@
 bool hantro_needs_postproc(const struct hantro_ctx *ctx,
 			   const struct hantro_fmt *fmt)
 {
-	struct hantro_dev *vpu = ctx->dev;
-
 	if (ctx->is_encoder)
 		return false;
-
-	if (!vpu->variant->postproc_fmts)
-		return false;
-
-	return fmt->fourcc != V4L2_PIX_FMT_NV12;
+	return fmt->postprocessed;
 }
 
 void hantro_postproc_enable(struct hantro_ctx *ctx)
@@ -132,9 +126,10 @@
 	unsigned int num_buffers = cap_queue->num_buffers;
 	unsigned int i, buf_size;
 
-	buf_size = ctx->dst_fmt.plane_fmt[0].sizeimage +
-		   hantro_h264_mv_size(ctx->dst_fmt.width,
-				       ctx->dst_fmt.height);
+	buf_size = ctx->dst_fmt.plane_fmt[0].sizeimage;
+	if (ctx->vpu_src_fmt->fourcc == V4L2_PIX_FMT_H264_SLICE)
+		buf_size += hantro_h264_mv_size(ctx->dst_fmt.width,
+						ctx->dst_fmt.height);
 
 	for (i = 0; i < num_buffers; ++i) {
 		struct hantro_aux_buf *priv = &ctx->postproc.dec_q[i];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/hantro_v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/hantro_v4l2.c
@@ -647,8 +647,12 @@
 	 * (for OUTPUT buffers, if userspace passes 0 bytesused, v4l2-core sets
 	 * it to buffer length).
 	 */
-	if (V4L2_TYPE_IS_CAPTURE(vq->type))
-		vb2_set_plane_payload(vb, 0, pix_fmt->plane_fmt[0].sizeimage);
+	if (V4L2_TYPE_IS_CAPTURE(vq->type)) {
+		if (ctx->is_encoder)
+			vb2_set_plane_payload(vb, 0, 0);
+		else
+			vb2_set_plane_payload(vb, 0, pix_fmt->plane_fmt[0].sizeimage);
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/imx8m_vpu_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/imx8m_vpu_hw.c
@@ -82,6 +82,7 @@
 	{
 		.fourcc = V4L2_PIX_FMT_YUYV,
 		.codec_mode = HANTRO_MODE_NONE,
+		.postprocessed = true,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/rockchip_vpu2_hw_jpeg_enc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/rockchip_vpu2_hw_jpeg_enc.c
@@ -171,3 +171,20 @@
 
 	return 0;
 }
+
+void rockchip_vpu2_jpeg_enc_done(struct hantro_ctx *ctx)
+{
+	struct hantro_dev *vpu = ctx->dev;
+	u32 bytesused = vepu_read(vpu, VEPU_REG_STR_BUF_LIMIT) / 8;
+	struct vb2_v4l2_buffer *dst_buf = hantro_get_dst_buf(ctx);
+
+	/*
+	 * TODO: Rework the JPEG encoder to eliminate the need
+	 * for a bounce buffer.
+	 */
+	memcpy(vb2_plane_vaddr(&dst_buf->vb2_buf, 0) +
+	       ctx->vpu_dst_fmt->header_size,
+	       ctx->jpeg_enc.bounce_buffer.cpu, bytesused);
+	vb2_set_plane_payload(&dst_buf->vb2_buf, 0,
+			      ctx->vpu_dst_fmt->header_size + bytesused);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/rockchip_vpu_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/rockchip_vpu_hw.c
@@ -62,6 +62,7 @@
 	{
 		.fourcc = V4L2_PIX_FMT_YUYV,
 		.codec_mode = HANTRO_MODE_NONE,
+		.postprocessed = true,
 	},
 };
 
@@ -343,7 +344,7 @@
 		.run = hantro_h1_jpeg_enc_run,
 		.reset = rockchip_vpu1_enc_reset,
 		.init = hantro_jpeg_enc_init,
-		.done = hantro_jpeg_enc_done,
+		.done = hantro_h1_jpeg_enc_done,
 		.exit = hantro_jpeg_enc_exit,
 	},
 	[HANTRO_MODE_H264_DEC] = {
@@ -371,7 +372,7 @@
 		.run = hantro_h1_jpeg_enc_run,
 		.reset = rockchip_vpu1_enc_reset,
 		.init = hantro_jpeg_enc_init,
-		.done = hantro_jpeg_enc_done,
+		.done = hantro_h1_jpeg_enc_done,
 		.exit = hantro_jpeg_enc_exit,
 	},
 	[HANTRO_MODE_H264_DEC] = {
@@ -399,6 +400,7 @@
 		.run = rockchip_vpu2_jpeg_enc_run,
 		.reset = rockchip_vpu2_enc_reset,
 		.init = hantro_jpeg_enc_init,
+		.done = rockchip_vpu2_jpeg_enc_done,
 		.exit = hantro_jpeg_enc_exit,
 	},
 	[HANTRO_MODE_H264_DEC] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/hantro/sama5d4_vdec_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/hantro/sama5d4_vdec_hw.c
@@ -15,6 +15,7 @@
 	{
 		.fourcc = V4L2_PIX_FMT_YUYV,
 		.codec_mode = HANTRO_MODE_NONE,
+		.postprocessed = true,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx-media-capture.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx-media-capture.c
@@ -501,14 +501,14 @@
 				 struct v4l2_streamparm *a)
 {
 	struct capture_priv *priv = video_drvdata(file);
-	struct v4l2_subdev_frame_interval fi;
+	struct v4l2_subdev_frame_interval fi = {
+		.pad = priv->src_sd_pad,
+	};
 	int ret;
 
 	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
 		return -EINVAL;
 
-	memset(&fi, 0, sizeof(fi));
-	fi.pad = priv->src_sd_pad;
 	ret = v4l2_subdev_call(priv->src_sd, video, g_frame_interval, &fi);
 	if (ret < 0)
 		return ret;
@@ -523,14 +523,14 @@
 				 struct v4l2_streamparm *a)
 {
 	struct capture_priv *priv = video_drvdata(file);
-	struct v4l2_subdev_frame_interval fi;
+	struct v4l2_subdev_frame_interval fi = {
+		.pad = priv->src_sd_pad,
+	};
 	int ret;
 
 	if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
 		return -EINVAL;
 
-	memset(&fi, 0, sizeof(fi));
-	fi.pad = priv->src_sd_pad;
 	fi.interval = a->parm.capture.timeperframe;
 	ret = v4l2_subdev_call(priv->src_sd, video, s_frame_interval, &fi);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx-media-csc-scaler.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx-media-csc-scaler.c
@@ -803,6 +803,7 @@
 
 	dev_dbg(priv->dev, "Releasing instance %p\n", ctx);
 
+	v4l2_ctrl_handler_free(&ctx->ctrl_hdlr);
 	v4l2_m2m_ctx_release(ctx->fh.m2m_ctx);
 	v4l2_fh_del(&ctx->fh);
 	v4l2_fh_exit(&ctx->fh);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx-media-dev-common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx-media-dev-common.c
@@ -367,6 +367,8 @@
 	imxmd->v4l2_dev.notify = imx_media_notify;
 	strscpy(imxmd->v4l2_dev.name, "imx-media",
 		sizeof(imxmd->v4l2_dev.name));
+	snprintf(imxmd->md.bus_info, sizeof(imxmd->md.bus_info),
+		 "platform:%s", dev_name(imxmd->md.dev));
 
 	media_device_init(&imxmd->md);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx-media-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx-media-of.c
@@ -55,22 +55,18 @@
 			break;
 
 		ret = imx_media_of_add_csi(imxmd, csi_np);
+		of_node_put(csi_np);
 		if (ret) {
 			/* unavailable or already added is not an error */
 			if (ret == -ENODEV || ret == -EEXIST) {
-				of_node_put(csi_np);
 				continue;
 			}
 
 			/* other error, can't continue */
-			goto err_out;
+			return ret;
 		}
 	}
 
 	return 0;
-
-err_out:
-	of_node_put(csi_np);
-	return ret;
 }
 EXPORT_SYMBOL_GPL(imx_media_add_of_subdevs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx-media-utils.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx-media-utils.c
@@ -432,15 +432,15 @@
 		       struct v4l2_subdev_state *sd_state)
 {
 	struct v4l2_mbus_framefmt *mf_try;
-	struct v4l2_subdev_format format;
 	unsigned int pad;
 	int ret;
 
 	for (pad = 0; pad < sd->entity.num_pads; pad++) {
-		memset(&format, 0, sizeof(format));
+		struct v4l2_subdev_format format = {
+			.pad = pad,
+			.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+		};
 
-		format.pad = pad;
-		format.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 		ret = v4l2_subdev_call(sd, pad, get_fmt, NULL, &format);
 		if (ret)
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx7-mipi-csis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx7-mipi-csis.c
@@ -32,7 +32,6 @@
 #include <media/v4l2-subdev.h>
 
 #define CSIS_DRIVER_NAME			"imx7-mipi-csis"
-#define CSIS_SUBDEV_NAME			CSIS_DRIVER_NAME
 
 #define CSIS_PAD_SINK				0
 #define CSIS_PAD_SOURCE				1
@@ -311,7 +310,6 @@
 	struct reset_control *mrst;
 	struct regulator *mipi_phy_regulator;
 	const struct mipi_csis_info *info;
-	u8 index;
 
 	struct v4l2_subdev sd;
 	struct media_pad pads[CSIS_PADS_NUM];
@@ -1303,8 +1301,8 @@
 
 	v4l2_subdev_init(sd, &mipi_csis_subdev_ops);
 	sd->owner = THIS_MODULE;
-	snprintf(sd->name, sizeof(sd->name), "%s.%d",
-		 CSIS_SUBDEV_NAME, state->index);
+	snprintf(sd->name, sizeof(sd->name), "csis-%s",
+		 dev_name(state->dev));
 
 	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
 	sd->ctrl_handler = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/imx/imx8mq-mipi-csi2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/imx/imx8mq-mipi-csi2.c
@@ -398,9 +398,6 @@
 	struct csi_state *state = mipi_sd_to_csi2_state(sd);
 	int ret = 0;
 
-	imx8mq_mipi_csi_write(state, CSI2RX_IRQ_MASK,
-			      CSI2RX_IRQ_MASK_ULPS_STATUS_CHANGE);
-
 	if (enable) {
 		ret = pm_runtime_resume_and_get(state->dev);
 		if (ret < 0)
@@ -696,7 +693,7 @@
  * Suspend/resume
  */
 
-static int imx8mq_mipi_csi_pm_suspend(struct device *dev, bool runtime)
+static int imx8mq_mipi_csi_pm_suspend(struct device *dev)
 {
 	struct v4l2_subdev *sd = dev_get_drvdata(dev);
 	struct csi_state *state = mipi_sd_to_csi2_state(sd);
@@ -708,36 +705,21 @@
 		imx8mq_mipi_csi_stop_stream(state);
 		imx8mq_mipi_csi_clk_disable(state);
 		state->state &= ~ST_POWERED;
-		if (!runtime)
-			state->state |= ST_SUSPENDED;
 	}
 
 	mutex_unlock(&state->lock);
 
-	ret = icc_set_bw(state->icc_path, 0, 0);
-	if (ret)
-		dev_err(dev, "icc_set_bw failed with %d\n", ret);
-
 	return ret ? -EAGAIN : 0;
 }
 
-static int imx8mq_mipi_csi_pm_resume(struct device *dev, bool runtime)
+static int imx8mq_mipi_csi_pm_resume(struct device *dev)
 {
 	struct v4l2_subdev *sd = dev_get_drvdata(dev);
 	struct csi_state *state = mipi_sd_to_csi2_state(sd);
 	int ret = 0;
 
-	ret = icc_set_bw(state->icc_path, 0, state->icc_path_bw);
-	if (ret) {
-		dev_err(dev, "icc_set_bw failed with %d\n", ret);
-		return ret;
-	}
-
 	mutex_lock(&state->lock);
 
-	if (!runtime && !(state->state & ST_SUSPENDED))
-		goto unlock;
-
 	if (!(state->state & ST_POWERED)) {
 		state->state |= ST_POWERED;
 		ret = imx8mq_mipi_csi_clk_enable(state);
@@ -758,22 +740,60 @@
 
 static int __maybe_unused imx8mq_mipi_csi_suspend(struct device *dev)
 {
-	return imx8mq_mipi_csi_pm_suspend(dev, false);
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct csi_state *state = mipi_sd_to_csi2_state(sd);
+	int ret;
+
+	ret = imx8mq_mipi_csi_pm_suspend(dev);
+	if (ret)
+		return ret;
+
+	state->state |= ST_SUSPENDED;
+
+	return ret;
 }
 
 static int __maybe_unused imx8mq_mipi_csi_resume(struct device *dev)
 {
-	return imx8mq_mipi_csi_pm_resume(dev, false);
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct csi_state *state = mipi_sd_to_csi2_state(sd);
+
+	if (!(state->state & ST_SUSPENDED))
+		return 0;
+
+	return imx8mq_mipi_csi_pm_resume(dev);
 }
 
 static int __maybe_unused imx8mq_mipi_csi_runtime_suspend(struct device *dev)
 {
-	return imx8mq_mipi_csi_pm_suspend(dev, true);
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct csi_state *state = mipi_sd_to_csi2_state(sd);
+	int ret;
+
+	ret = imx8mq_mipi_csi_pm_suspend(dev);
+	if (ret)
+		return ret;
+
+	ret = icc_set_bw(state->icc_path, 0, 0);
+	if (ret)
+		dev_err(dev, "icc_set_bw failed with %d\n", ret);
+
+	return ret;
 }
 
 static int __maybe_unused imx8mq_mipi_csi_runtime_resume(struct device *dev)
 {
-	return imx8mq_mipi_csi_pm_resume(dev, true);
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct csi_state *state = mipi_sd_to_csi2_state(sd);
+	int ret;
+
+	ret = icc_set_bw(state->icc_path, 0, state->icc_path_bw);
+	if (ret) {
+		dev_err(dev, "icc_set_bw failed with %d\n", ret);
+		return ret;
+	}
+
+	return imx8mq_mipi_csi_pm_resume(dev);
 }
 
 static const struct dev_pm_ops imx8mq_mipi_csi_pm_ops = {
@@ -921,7 +941,7 @@
 	/* Enable runtime PM. */
 	pm_runtime_enable(dev);
 	if (!pm_runtime_enabled(dev)) {
-		ret = imx8mq_mipi_csi_pm_resume(dev, true);
+		ret = imx8mq_mipi_csi_runtime_resume(dev);
 		if (ret < 0)
 			goto icc;
 	}
@@ -934,7 +954,7 @@
 
 cleanup:
 	pm_runtime_disable(&pdev->dev);
-	imx8mq_mipi_csi_pm_suspend(&pdev->dev, true);
+	imx8mq_mipi_csi_runtime_suspend(&pdev->dev);
 
 	media_entity_cleanup(&state->sd.entity);
 	v4l2_async_notifier_unregister(&state->notifier);
@@ -958,7 +978,7 @@
 	v4l2_async_unregister_subdev(&state->sd);
 
 	pm_runtime_disable(&pdev->dev);
-	imx8mq_mipi_csi_pm_suspend(&pdev->dev, true);
+	imx8mq_mipi_csi_runtime_suspend(&pdev->dev);
 	media_entity_cleanup(&state->sd.entity);
 	mutex_destroy(&state->lock);
 	pm_runtime_set_suspended(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/ipu3/ipu3-css-fw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/ipu3/ipu3-css-fw.c
@@ -124,12 +124,11 @@
 	/* Check and display fw header info */
 
 	css->fwp = (struct imgu_fw_header *)css->fw->data;
-	if (css->fw->size < sizeof(struct imgu_fw_header *) ||
+	if (css->fw->size < struct_size(css->fwp, binary_header, 1) ||
 	    css->fwp->file_header.h_size != sizeof(struct imgu_fw_bi_file_h))
 		goto bad_fw;
-	if (sizeof(struct imgu_fw_bi_file_h) +
-	    css->fwp->file_header.binary_nr * sizeof(struct imgu_fw_info) >
-	    css->fw->size)
+	if (struct_size(css->fwp, binary_header,
+			css->fwp->file_header.binary_nr) > css->fw->size)
 		goto bad_fw;
 
 	dev_info(dev, "loaded firmware version %.64s, %u binaries, %zu bytes\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/ipu3/ipu3-css-fw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/ipu3/ipu3-css-fw.h
@@ -171,7 +171,7 @@
 
 struct imgu_fw_header {
 	struct imgu_fw_bi_file_h file_header;
-	struct imgu_fw_info binary_header[1];	/* binary_nr items */
+	struct imgu_fw_info binary_header[];	/* binary_nr items */
 };
 
 /******************* Firmware functions *******************/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/ipu3/ipu3-v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/ipu3/ipu3-v4l2.c
@@ -188,37 +188,50 @@
 	return 0;
 }
 
+static struct v4l2_rect *
+imgu_subdev_get_crop(struct imgu_v4l2_subdev *sd,
+		     struct v4l2_subdev_state *sd_state, unsigned int pad,
+		     enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_crop(&sd->subdev, sd_state, pad);
+	else
+		return &sd->rect.eff;
+}
+
+static struct v4l2_rect *
+imgu_subdev_get_compose(struct imgu_v4l2_subdev *sd,
+			struct v4l2_subdev_state *sd_state, unsigned int pad,
+			enum v4l2_subdev_format_whence which)
+{
+	if (which == V4L2_SUBDEV_FORMAT_TRY)
+		return v4l2_subdev_get_try_compose(&sd->subdev, sd_state, pad);
+	else
+		return &sd->rect.bds;
+}
+
 static int imgu_subdev_get_selection(struct v4l2_subdev *sd,
 				     struct v4l2_subdev_state *sd_state,
 				     struct v4l2_subdev_selection *sel)
 {
-	struct v4l2_rect *try_sel, *r;
-	struct imgu_v4l2_subdev *imgu_sd = container_of(sd,
-							struct imgu_v4l2_subdev,
-							subdev);
+	struct imgu_v4l2_subdev *imgu_sd =
+		container_of(sd, struct imgu_v4l2_subdev, subdev);
 
 	if (sel->pad != IMGU_NODE_IN)
 		return -EINVAL;
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP:
-		try_sel = v4l2_subdev_get_try_crop(sd, sd_state, sel->pad);
-		r = &imgu_sd->rect.eff;
-		break;
+		sel->r = *imgu_subdev_get_crop(imgu_sd, sd_state, sel->pad,
+					       sel->which);
+		return 0;
 	case V4L2_SEL_TGT_COMPOSE:
-		try_sel = v4l2_subdev_get_try_compose(sd, sd_state, sel->pad);
-		r = &imgu_sd->rect.bds;
-		break;
+		sel->r = *imgu_subdev_get_compose(imgu_sd, sd_state, sel->pad,
+						  sel->which);
+		return 0;
 	default:
 		return -EINVAL;
 	}
-
-	if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
-		sel->r = *try_sel;
-	else
-		sel->r = *r;
-
-	return 0;
 }
 
 static int imgu_subdev_set_selection(struct v4l2_subdev *sd,
@@ -226,10 +239,9 @@
 				     struct v4l2_subdev_selection *sel)
 {
 	struct imgu_device *imgu = v4l2_get_subdevdata(sd);
-	struct imgu_v4l2_subdev *imgu_sd = container_of(sd,
-							struct imgu_v4l2_subdev,
-							subdev);
-	struct v4l2_rect *rect, *try_sel;
+	struct imgu_v4l2_subdev *imgu_sd =
+		container_of(sd, struct imgu_v4l2_subdev, subdev);
+	struct v4l2_rect *rect;
 
 	dev_dbg(&imgu->pci_dev->dev,
 		 "set subdev %u sel which %u target 0x%4x rect [%ux%u]",
@@ -241,22 +253,18 @@
 
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP:
-		try_sel = v4l2_subdev_get_try_crop(sd, sd_state, sel->pad);
-		rect = &imgu_sd->rect.eff;
+		rect = imgu_subdev_get_crop(imgu_sd, sd_state, sel->pad,
+					    sel->which);
 		break;
 	case V4L2_SEL_TGT_COMPOSE:
-		try_sel = v4l2_subdev_get_try_compose(sd, sd_state, sel->pad);
-		rect = &imgu_sd->rect.bds;
+		rect = imgu_subdev_get_compose(imgu_sd, sd_state, sel->pad,
+					       sel->which);
 		break;
 	default:
 		return -EINVAL;
 	}
 
-	if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
-		*try_sel = sel->r;
-	else
-		*rect = sel->r;
-
+	*rect = sel->r;
 	return 0;
 }
 
@@ -592,11 +600,12 @@
 static int imgu_vidioc_querycap(struct file *file, void *fh,
 				struct v4l2_capability *cap)
 {
-	struct imgu_video_device *node = file_to_intel_imgu_node(file);
+	struct imgu_device *imgu = video_drvdata(file);
 
 	strscpy(cap->driver, IMGU_NAME, sizeof(cap->driver));
 	strscpy(cap->card, IMGU_NAME, sizeof(cap->card));
-	snprintf(cap->bus_info, sizeof(cap->bus_info), "PCI:%s", node->name);
+	snprintf(cap->bus_info, sizeof(cap->bus_info), "PCI:%s",
+		 pci_name(imgu->pci_dev));
 
 	return 0;
 }
@@ -696,7 +705,7 @@
 
 		/* CSS expects some format on OUT queue */
 		if (i != IPU3_CSS_QUEUE_OUT &&
-		    !imgu_pipe->nodes[inode].enabled) {
+		    !imgu_pipe->nodes[inode].enabled && !try) {
 			fmts[i] = NULL;
 			continue;
 		}
@@ -1059,6 +1068,11 @@
 	struct imgu_media_pipe *imgu_pipe = &imgu->imgu_pipe[pipe];
 
 	/* Initialize subdev media entity */
+	imgu_sd->subdev.entity.ops = &imgu_media_ops;
+	for (i = 0; i < IMGU_NODE_NUM; i++) {
+		imgu_sd->subdev_pads[i].flags = imgu_pipe->nodes[i].output ?
+			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
+	}
 	r = media_entity_pads_init(&imgu_sd->subdev.entity, IMGU_NODE_NUM,
 				   imgu_sd->subdev_pads);
 	if (r) {
@@ -1066,11 +1080,6 @@
 			"failed initialize subdev media entity (%d)\n", r);
 		return r;
 	}
-	imgu_sd->subdev.entity.ops = &imgu_media_ops;
-	for (i = 0; i < IMGU_NODE_NUM; i++) {
-		imgu_sd->subdev_pads[i].flags = imgu_pipe->nodes[i].output ?
-			MEDIA_PAD_FL_SINK : MEDIA_PAD_FL_SOURCE;
-	}
 
 	/* Initialize subdev */
 	v4l2_subdev_init(&imgu_sd->subdev, &imgu_subdev_ops);
@@ -1165,15 +1174,15 @@
 	}
 
 	/* Initialize media entities */
+	node->vdev_pad.flags = node->output ?
+		MEDIA_PAD_FL_SOURCE : MEDIA_PAD_FL_SINK;
+	vdev->entity.ops = NULL;
 	r = media_entity_pads_init(&vdev->entity, 1, &node->vdev_pad);
 	if (r) {
 		dev_err(dev, "failed initialize media entity (%d)\n", r);
 		mutex_destroy(&node->lock);
 		return r;
 	}
-	node->vdev_pad.flags = node->output ?
-		MEDIA_PAD_FL_SOURCE : MEDIA_PAD_FL_SINK;
-	vdev->entity.ops = NULL;
 
 	/* Initialize vbq */
 	vbq->type = node->vdev_fmt.type;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/meson/vdec/esparser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/meson/vdec/esparser.c
@@ -328,7 +328,12 @@
 
 	offset = esparser_get_offset(sess);
 
-	amvdec_add_ts(sess, vb->timestamp, vbuf->timecode, offset, vbuf->flags);
+	ret = amvdec_add_ts(sess, vb->timestamp, vbuf->timecode, offset, vbuf->flags);
+	if (ret) {
+		v4l2_m2m_buf_done(vbuf, VB2_BUF_STATE_ERROR);
+		return ret;
+	}
+
 	dev_dbg(core->dev, "esparser: ts = %llu pld_size = %u offset = %08X flags = %08X\n",
 		vb->timestamp, payload_size, offset, vbuf->flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/meson/vdec/vdec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/meson/vdec/vdec.c
@@ -1105,6 +1105,7 @@
 
 err_vdev_release:
 	video_device_release(vdev);
+	v4l2_device_unregister(&core->v4l2_dev);
 	return ret;
 }
 
@@ -1113,6 +1114,7 @@
 	struct amvdec_core *core = platform_get_drvdata(pdev);
 
 	video_unregister_device(core->vdev_dec);
+	v4l2_device_unregister(&core->v4l2_dev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/meson/vdec/vdec_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/meson/vdec/vdec_helpers.c
@@ -227,13 +227,16 @@
 }
 EXPORT_SYMBOL_GPL(amvdec_set_canvases);
 
-void amvdec_add_ts(struct amvdec_session *sess, u64 ts,
-		   struct v4l2_timecode tc, u32 offset, u32 vbuf_flags)
+int amvdec_add_ts(struct amvdec_session *sess, u64 ts,
+		  struct v4l2_timecode tc, u32 offset, u32 vbuf_flags)
 {
 	struct amvdec_timestamp *new_ts;
 	unsigned long flags;
 
 	new_ts = kzalloc(sizeof(*new_ts), GFP_KERNEL);
+	if (!new_ts)
+		return -ENOMEM;
+
 	new_ts->ts = ts;
 	new_ts->tc = tc;
 	new_ts->offset = offset;
@@ -242,6 +245,7 @@
 	spin_lock_irqsave(&sess->ts_spinlock, flags);
 	list_add_tail(&new_ts->list, &sess->timestamps);
 	spin_unlock_irqrestore(&sess->ts_spinlock, flags);
+	return 0;
 }
 EXPORT_SYMBOL_GPL(amvdec_add_ts);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/meson/vdec/vdec_helpers.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/meson/vdec/vdec_helpers.h
@@ -55,8 +55,8 @@
  * @offset: offset in the VIFIFO where the associated packet was written
  * @flags the vb2_v4l2_buffer flags
  */
-void amvdec_add_ts(struct amvdec_session *sess, u64 ts,
-		   struct v4l2_timecode tc, u32 offset, u32 flags);
+int amvdec_add_ts(struct amvdec_session *sess, u64 ts,
+		  struct v4l2_timecode tc, u32 offset, u32 flags);
 void amvdec_remove_ts(struct amvdec_session *sess, u64 ts);
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/meson/vdec/vdec_hevc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/meson/vdec/vdec_hevc.c
@@ -167,8 +167,12 @@
 
 	clk_set_rate(core->vdec_hevc_clk, 666666666);
 	ret = clk_prepare_enable(core->vdec_hevc_clk);
-	if (ret)
+	if (ret) {
+		if (core->platform->revision == VDEC_REVISION_G12A ||
+		    core->platform->revision == VDEC_REVISION_SM1)
+			clk_disable_unprepare(core->vdec_hevcf_clk);
 		return ret;
+	}
 
 	if (core->platform->revision == VDEC_REVISION_SM1)
 		regmap_update_bits(core->regmap_ao, AO_RTI_GEN_PWR_SLEEP0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/omap4iss/iss_video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/omap4iss/iss_video.c
@@ -244,7 +244,9 @@
 __iss_video_get_format(struct iss_video *video,
 		       struct v4l2_mbus_framefmt *format)
 {
-	struct v4l2_subdev_format fmt;
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+	};
 	struct v4l2_subdev *subdev;
 	u32 pad;
 	int ret;
@@ -253,9 +255,7 @@
 	if (!subdev)
 		return -EINVAL;
 
-	memset(&fmt, 0, sizeof(fmt));
 	fmt.pad = pad;
-	fmt.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 
 	mutex_lock(&video->mutex);
 	ret = v4l2_subdev_call(subdev, pad, get_fmt, NULL, &fmt);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/rkvdec/rkvdec-h264.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/rkvdec/rkvdec-h264.c
@@ -112,6 +112,7 @@
 	const struct v4l2_ctrl_h264_sps *sps;
 	const struct v4l2_ctrl_h264_pps *pps;
 	const struct v4l2_ctrl_h264_scaling_matrix *scaling_matrix;
+	int ref_buf_idx[V4L2_H264_NUM_DPB_ENTRIES];
 };
 
 struct rkvdec_h264_ctx {
@@ -661,8 +662,8 @@
 	WRITE_PPS(0xff, PROFILE_IDC);
 	WRITE_PPS(1, CONSTRAINT_SET3_FLAG);
 	WRITE_PPS(sps->chroma_format_idc, CHROMA_FORMAT_IDC);
-	WRITE_PPS(sps->bit_depth_luma_minus8 + 8, BIT_DEPTH_LUMA);
-	WRITE_PPS(sps->bit_depth_chroma_minus8 + 8, BIT_DEPTH_CHROMA);
+	WRITE_PPS(sps->bit_depth_luma_minus8, BIT_DEPTH_LUMA);
+	WRITE_PPS(sps->bit_depth_chroma_minus8, BIT_DEPTH_CHROMA);
 	WRITE_PPS(0, QPPRIME_Y_ZERO_TRANSFORM_BYPASS_FLAG);
 	WRITE_PPS(sps->log2_max_frame_num_minus4, LOG2_MAX_FRAME_NUM_MINUS4);
 	WRITE_PPS(sps->max_num_ref_frames, MAX_NUM_REF_FRAMES);
@@ -725,6 +726,26 @@
 	}
 }
 
+static void lookup_ref_buf_idx(struct rkvdec_ctx *ctx,
+			       struct rkvdec_h264_run *run)
+{
+	const struct v4l2_ctrl_h264_decode_params *dec_params = run->decode_params;
+	u32 i;
+
+	for (i = 0; i < ARRAY_SIZE(dec_params->dpb); i++) {
+		struct v4l2_m2m_ctx *m2m_ctx = ctx->fh.m2m_ctx;
+		const struct v4l2_h264_dpb_entry *dpb = run->decode_params->dpb;
+		struct vb2_queue *cap_q = &m2m_ctx->cap_q_ctx.q;
+		int buf_idx = -1;
+
+		if (dpb[i].flags & V4L2_H264_DPB_ENTRY_FLAG_ACTIVE)
+			buf_idx = vb2_find_timestamp(cap_q,
+						     dpb[i].reference_ts, 0);
+
+		run->ref_buf_idx[i] = buf_idx;
+	}
+}
+
 static void assemble_hw_rps(struct rkvdec_ctx *ctx,
 			    struct rkvdec_h264_run *run)
 {
@@ -762,7 +783,7 @@
 
 	for (j = 0; j < RKVDEC_NUM_REFLIST; j++) {
 		for (i = 0; i < h264_ctx->reflists.num_valid; i++) {
-			u8 dpb_valid = 0;
+			bool dpb_valid = run->ref_buf_idx[i] >= 0;
 			u8 idx = 0;
 
 			switch (j) {
@@ -779,8 +800,6 @@
 
 			if (idx >= ARRAY_SIZE(dec_params->dpb))
 				continue;
-			dpb_valid = !!(dpb[idx].flags &
-				       V4L2_H264_DPB_ENTRY_FLAG_ACTIVE);
 
 			set_ps_field(hw_rps, DPB_INFO(i, j),
 				     idx | dpb_valid << 4);
@@ -859,13 +878,8 @@
 	    unsigned int dpb_idx)
 {
 	struct v4l2_m2m_ctx *m2m_ctx = ctx->fh.m2m_ctx;
-	const struct v4l2_h264_dpb_entry *dpb = run->decode_params->dpb;
 	struct vb2_queue *cap_q = &m2m_ctx->cap_q_ctx.q;
-	int buf_idx = -1;
-
-	if (dpb[dpb_idx].flags & V4L2_H264_DPB_ENTRY_FLAG_ACTIVE)
-		buf_idx = vb2_find_timestamp(cap_q,
-					     dpb[dpb_idx].reference_ts, 0);
+	int buf_idx = run->ref_buf_idx[dpb_idx];
 
 	/*
 	 * If a DPB entry is unused or invalid, address of current destination
@@ -1015,8 +1029,9 @@
 	struct v4l2_pix_format_mplane *fmt = &f->fmt.pix_mp;
 
 	fmt->num_planes = 1;
-	fmt->plane_fmt[0].sizeimage = fmt->width * fmt->height *
-				      RKVDEC_H264_MAX_DEPTH_IN_BYTES;
+	if (!fmt->plane_fmt[0].sizeimage)
+		fmt->plane_fmt[0].sizeimage = fmt->width * fmt->height *
+					      RKVDEC_H264_MAX_DEPTH_IN_BYTES;
 	return 0;
 }
 
@@ -1101,6 +1116,7 @@
 
 	assemble_hw_scaling_list(ctx, &run);
 	assemble_hw_pps(ctx, &run);
+	lookup_ref_buf_idx(ctx, &run);
 	assemble_hw_rps(ctx, &run);
 	config_registers(ctx, &run);
 
@@ -1108,8 +1124,8 @@
 
 	schedule_delayed_work(&rkvdec->watchdog_work, msecs_to_jiffies(2000));
 
-	writel(0xffffffff, rkvdec->regs + RKVDEC_REG_STRMD_ERR_EN);
-	writel(0xffffffff, rkvdec->regs + RKVDEC_REG_H264_ERR_E);
+	writel(0, rkvdec->regs + RKVDEC_REG_STRMD_ERR_EN);
+	writel(0, rkvdec->regs + RKVDEC_REG_H264_ERR_E);
 	writel(1, rkvdec->regs + RKVDEC_REG_PREF_LUMA_CACHE_COMMAND);
 	writel(1, rkvdec->regs + RKVDEC_REG_PREF_CHR_CACHE_COMMAND);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/rkvdec/rkvdec.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/rkvdec/rkvdec.c
@@ -111,7 +111,7 @@
 			.max_width = 4096,
 			.step_width = 16,
 			.min_height = 48,
-			.max_height = 2304,
+			.max_height = 2560,
 			.step_height = 16,
 		},
 		.ctrls = &rkvdec_h264_ctrls,
@@ -280,31 +280,20 @@
 	return 0;
 }
 
-static int rkvdec_s_fmt(struct file *file, void *priv,
-			struct v4l2_format *f,
-			int (*try_fmt)(struct file *, void *,
-				       struct v4l2_format *))
+static int rkvdec_s_capture_fmt(struct file *file, void *priv,
+				struct v4l2_format *f)
 {
 	struct rkvdec_ctx *ctx = fh_to_rkvdec_ctx(priv);
 	struct vb2_queue *vq;
+	int ret;
 
-	if (!try_fmt)
-		return -EINVAL;
-
-	vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx, f->type);
+	/* Change not allowed if queue is busy */
+	vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx,
+			     V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE);
 	if (vb2_is_busy(vq))
 		return -EBUSY;
 
-	return try_fmt(file, priv, f);
-}
-
-static int rkvdec_s_capture_fmt(struct file *file, void *priv,
-				struct v4l2_format *f)
-{
-	struct rkvdec_ctx *ctx = fh_to_rkvdec_ctx(priv);
-	int ret;
-
-	ret = rkvdec_s_fmt(file, priv, f, rkvdec_try_capture_fmt);
+	ret = rkvdec_try_capture_fmt(file, priv, f);
 	if (ret)
 		return ret;
 
@@ -319,10 +308,21 @@
 	struct v4l2_m2m_ctx *m2m_ctx = ctx->fh.m2m_ctx;
 	const struct rkvdec_coded_fmt_desc *desc;
 	struct v4l2_format *cap_fmt;
-	struct vb2_queue *peer_vq;
+	struct vb2_queue *peer_vq, *vq;
 	int ret;
 
 	/*
+	 * In order to support dynamic resolution change, the decoder admits
+	 * a resolution change, as long as the pixelformat remains. Can't be
+	 * done if streaming.
+	 */
+	vq = v4l2_m2m_get_vq(m2m_ctx, V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE);
+	if (vb2_is_streaming(vq) ||
+	    (vb2_is_busy(vq) &&
+	     f->fmt.pix_mp.pixelformat != ctx->coded_fmt.fmt.pix_mp.pixelformat))
+		return -EBUSY;
+
+	/*
 	 * Since format change on the OUTPUT queue will reset the CAPTURE
 	 * queue, we can't allow doing so when the CAPTURE queue has buffers
 	 * allocated.
@@ -331,7 +331,7 @@
 	if (vb2_is_busy(peer_vq))
 		return -EBUSY;
 
-	ret = rkvdec_s_fmt(file, priv, f, rkvdec_try_output_fmt);
+	ret = rkvdec_try_output_fmt(file, priv, f);
 	if (ret)
 		return ret;
 
@@ -967,7 +967,6 @@
 static int rkvdec_probe(struct platform_device *pdev)
 {
 	struct rkvdec_dev *rkvdec;
-	struct resource *res;
 	unsigned int i;
 	int ret, irq;
 
@@ -999,8 +998,7 @@
 	 */
 	clk_set_rate(rkvdec->clocks[0].clk, 500 * 1000 * 1000);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	rkvdec->regs = devm_ioremap_resource(&pdev->dev, res);
+	rkvdec->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(rkvdec->regs))
 		return PTR_ERR(rkvdec->regs);
 
@@ -1044,6 +1042,8 @@
 {
 	struct rkvdec_dev *rkvdec = platform_get_drvdata(pdev);
 
+	cancel_delayed_work_sync(&rkvdec->watchdog_work);
+
 	rkvdec_v4l2_cleanup(rkvdec);
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_dont_use_autosuspend(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/sunxi/cedrus/cedrus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/sunxi/cedrus/cedrus.c
@@ -369,6 +369,8 @@
 	if (!dev)
 		return -ENOMEM;
 
+	platform_set_drvdata(pdev, dev);
+
 	dev->vfd = cedrus_video_device;
 	dev->dev = &pdev->dev;
 	dev->pdev = pdev;
@@ -440,8 +442,6 @@
 		goto err_m2m_mc;
 	}
 
-	platform_set_drvdata(pdev, dev);
-
 	return 0;
 
 err_m2m_mc:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/sunxi/cedrus/cedrus_h264.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/sunxi/cedrus/cedrus_h264.c
@@ -38,7 +38,7 @@
 
 #define CEDRUS_H264_FRAME_NUM		18
 
-#define CEDRUS_NEIGHBOR_INFO_BUF_SIZE	(16 * SZ_1K)
+#define CEDRUS_NEIGHBOR_INFO_BUF_SIZE	(32 * SZ_1K)
 #define CEDRUS_MIN_PIC_INFO_BUF_SIZE       (130 * SZ_1K)
 
 static void cedrus_h264_write_sram(struct cedrus_dev *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/sunxi/cedrus/cedrus_h265.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/sunxi/cedrus/cedrus_h265.c
@@ -23,7 +23,7 @@
  * Subsequent BSP implementations seem to double the neighbor info buffer size
  * for the H6 SoC, which may be related to 10 bit H265 support.
  */
-#define CEDRUS_H265_NEIGHBOR_INFO_BUF_SIZE	(397 * SZ_1K)
+#define CEDRUS_H265_NEIGHBOR_INFO_BUF_SIZE	(794 * SZ_1K)
 #define CEDRUS_H265_ENTRY_POINTS_BUF_SIZE	(4 * SZ_1K)
 #define CEDRUS_H265_MV_COL_BUF_UNIT_CTB_SIZE	160
 
@@ -147,6 +147,9 @@
 			dpb[i].pic_order_cnt[1]
 		};
 
+		if (buffer_index < 0)
+			continue;
+
 		cedrus_h265_frame_info_write_single(ctx, i, dpb[i].field_pic,
 						    pic_order_cnt,
 						    buffer_index);
@@ -231,8 +234,9 @@
 		cedrus_write(dev, VE_DEC_H265_TRIGGER,
 			     VE_DEC_H265_TRIGGER_FLUSH_BITS |
 			     VE_DEC_H265_TRIGGER_TYPE_N_BITS(tmp));
-		while (cedrus_read(dev, VE_DEC_H265_STATUS) & VE_DEC_H265_STATUS_VLD_BUSY)
-			udelay(1);
+
+		if (cedrus_wait_for(dev, VE_DEC_H265_STATUS, VE_DEC_H265_STATUS_VLD_BUSY))
+			dev_err_ratelimited(dev->dev, "timed out waiting to skip bits\n");
 
 		count += tmp;
 	}
@@ -495,7 +499,6 @@
 
 	reg = VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_TC_OFFSET_DIV2(slice_params->slice_tc_offset_div2) |
 	      VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_BETA_OFFSET_DIV2(slice_params->slice_beta_offset_div2) |
-	      VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_POC_BIGEST_IN_RPS_ST(decode_params->num_poc_st_curr_after == 0) |
 	      VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_CR_QP_OFFSET(slice_params->slice_cr_qp_offset) |
 	      VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_CB_QP_OFFSET(slice_params->slice_cb_qp_offset) |
 	      VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_QP_DELTA(slice_params->slice_qp_delta);
@@ -508,6 +511,9 @@
 				V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_LOOP_FILTER_ACROSS_SLICES_ENABLED,
 				slice_params->flags);
 
+	if (decode_params->num_poc_st_curr_after == 0)
+		reg |= VE_DEC_H265_DEC_SLICE_HDR_INFO1_FLAG_SLICE_NOT_LOW_DELAY;
+
 	cedrus_write(dev, VE_DEC_H265_DEC_SLICE_HDR_INFO1, reg);
 
 	chroma_log2_weight_denom = pred_weight_table->luma_log2_weight_denom +
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/sunxi/cedrus/cedrus_hw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/sunxi/cedrus/cedrus_hw.c
@@ -147,12 +147,12 @@
 {
 	struct cedrus_dev *dev = dev_get_drvdata(device);
 
-	reset_control_assert(dev->rstc);
-
 	clk_disable_unprepare(dev->ram_clk);
 	clk_disable_unprepare(dev->mod_clk);
 	clk_disable_unprepare(dev->ahb_clk);
 
+	reset_control_assert(dev->rstc);
+
 	return 0;
 }
 
@@ -161,11 +161,18 @@
 	struct cedrus_dev *dev = dev_get_drvdata(device);
 	int ret;
 
+	ret = reset_control_reset(dev->rstc);
+	if (ret) {
+		dev_err(dev->dev, "Failed to apply reset\n");
+
+		return ret;
+	}
+
 	ret = clk_prepare_enable(dev->ahb_clk);
 	if (ret) {
 		dev_err(dev->dev, "Failed to enable AHB clock\n");
 
-		return ret;
+		goto err_rst;
 	}
 
 	ret = clk_prepare_enable(dev->mod_clk);
@@ -182,21 +189,14 @@
 		goto err_mod_clk;
 	}
 
-	ret = reset_control_reset(dev->rstc);
-	if (ret) {
-		dev_err(dev->dev, "Failed to apply reset\n");
-
-		goto err_ram_clk;
-	}
-
 	return 0;
 
-err_ram_clk:
-	clk_disable_unprepare(dev->ram_clk);
 err_mod_clk:
 	clk_disable_unprepare(dev->mod_clk);
 err_ahb_clk:
 	clk_disable_unprepare(dev->ahb_clk);
+err_rst:
+	reset_control_assert(dev->rstc);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/sunxi/cedrus/cedrus_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/sunxi/cedrus/cedrus_regs.h
@@ -377,13 +377,12 @@
 
 #define VE_DEC_H265_DEC_SLICE_HDR_INFO1_FLAG_SLICE_DEBLOCKING_FILTER_DISABLED BIT(23)
 #define VE_DEC_H265_DEC_SLICE_HDR_INFO1_FLAG_SLICE_LOOP_FILTER_ACROSS_SLICES_ENABLED BIT(22)
+#define VE_DEC_H265_DEC_SLICE_HDR_INFO1_FLAG_SLICE_NOT_LOW_DELAY BIT(21)
 
 #define VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_TC_OFFSET_DIV2(v) \
 	SHIFT_AND_MASK_BITS(v, 31, 28)
 #define VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_BETA_OFFSET_DIV2(v) \
 	SHIFT_AND_MASK_BITS(v, 27, 24)
-#define VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_POC_BIGEST_IN_RPS_ST(v) \
-	((v) ? BIT(21) : 0)
 #define VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_CR_QP_OFFSET(v) \
 	SHIFT_AND_MASK_BITS(v, 20, 16)
 #define VE_DEC_H265_DEC_SLICE_HDR_INFO1_SLICE_CB_QP_OFFSET(v) \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/tegra-video/csi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/tegra-video/csi.c
@@ -433,7 +433,7 @@
 	for (i = 0; i < chan->numgangports; i++)
 		chan->csi_port_nums[i] = port_num + i * CSI_PORTS_PER_BRICK;
 
-	chan->of_node = node;
+	chan->of_node = of_node_get(node);
 	chan->numpads = num_pads;
 	if (num_pads & 0x2) {
 		chan->pads[0].flags = MEDIA_PAD_FL_SINK;
@@ -448,6 +448,7 @@
 	chan->mipi = tegra_mipi_request(csi->dev, node);
 	if (IS_ERR(chan->mipi)) {
 		ret = PTR_ERR(chan->mipi);
+		chan->mipi = NULL;
 		dev_err(csi->dev, "failed to get mipi device: %d\n", ret);
 	}
 
@@ -640,6 +641,7 @@
 			media_entity_cleanup(&subdev->entity);
 		}
 
+		of_node_put(chan->of_node);
 		list_del(&chan->list);
 		kfree(chan);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/tegra-video/csi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/tegra-video/csi.h
@@ -56,7 +56,7 @@
  * @framerate: active framerate for TPG
  * @h_blank: horizontal blanking for TPG active format
  * @v_blank: vertical blanking for TPG active format
- * @mipi: mipi device for corresponding csi channel pads
+ * @mipi: mipi device for corresponding csi channel pads, or NULL if not applicable (TPG, error)
  * @pixel_rate: active pixel rate from the sensor on this channel
  */
 struct tegra_csi_channel {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/zoran/zoran.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/zoran/zoran.h
@@ -313,6 +313,6 @@
 
 #endif
 
-int zoran_queue_init(struct zoran *zr, struct vb2_queue *vq);
+int zoran_queue_init(struct zoran *zr, struct vb2_queue *vq, int dir);
 void zoran_queue_exit(struct zoran *zr);
 int zr_set_buf(struct zoran *zr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/zoran/zoran_card.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/zoran/zoran_card.c
@@ -803,6 +803,52 @@
 	return 0;
 }
 
+static int zoran_init_video_device(struct zoran *zr, struct video_device *video_dev, int dir)
+{
+	int err;
+
+	/* Now add the template and register the device unit. */
+	*video_dev = zoran_template;
+	video_dev->v4l2_dev = &zr->v4l2_dev;
+	video_dev->lock = &zr->lock;
+	video_dev->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_READWRITE | dir;
+
+	strscpy(video_dev->name, ZR_DEVNAME(zr), sizeof(video_dev->name));
+	/*
+	 * It's not a mem2mem device, but you can both capture and output from one and the same
+	 * device. This should really be split up into two device nodes, but that's a job for
+	 * another day.
+	 */
+	video_dev->vfl_dir = VFL_DIR_M2M;
+	zoran_queue_init(zr, &zr->vq, V4L2_BUF_TYPE_VIDEO_CAPTURE);
+
+	err = video_register_device(video_dev, VFL_TYPE_VIDEO, video_nr[zr->id]);
+	if (err < 0)
+		return err;
+	video_set_drvdata(video_dev, zr);
+	return 0;
+}
+
+static void zoran_exit_video_devices(struct zoran *zr)
+{
+	video_unregister_device(zr->video_dev);
+	kfree(zr->video_dev);
+}
+
+static int zoran_init_video_devices(struct zoran *zr)
+{
+	int err;
+
+	zr->video_dev = video_device_alloc();
+	if (!zr->video_dev)
+		return -ENOMEM;
+
+	err = zoran_init_video_device(zr, zr->video_dev, V4L2_CAP_VIDEO_CAPTURE);
+	if (err)
+		kfree(zr->video_dev);
+	return err;
+}
+
 void zoran_open_init_params(struct zoran *zr)
 {
 	int i;
@@ -874,17 +920,11 @@
 	zoran_open_init_params(zr);
 
 	/* allocate memory *before* doing anything to the hardware in case allocation fails */
-	zr->video_dev = video_device_alloc();
-	if (!zr->video_dev) {
-		err = -ENOMEM;
-		goto exit;
-	}
 	zr->stat_com = dma_alloc_coherent(&zr->pci_dev->dev,
 					  BUZ_NUM_STAT_COM * sizeof(u32),
 					  &zr->p_sc, GFP_KERNEL);
 	if (!zr->stat_com) {
-		err = -ENOMEM;
-		goto exit_video;
+		return -ENOMEM;
 	}
 	for (j = 0; j < BUZ_NUM_STAT_COM; j++)
 		zr->stat_com[j] = cpu_to_le32(1); /* mark as unavailable to zr36057 */
@@ -897,26 +937,9 @@
 		goto exit_statcom;
 	}
 
-	/* Now add the template and register the device unit. */
-	*zr->video_dev = zoran_template;
-	zr->video_dev->v4l2_dev = &zr->v4l2_dev;
-	zr->video_dev->lock = &zr->lock;
-	zr->video_dev->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_CAPTURE;
-
-	strscpy(zr->video_dev->name, ZR_DEVNAME(zr), sizeof(zr->video_dev->name));
-	/*
-	 * It's not a mem2mem device, but you can both capture and output from one and the same
-	 * device. This should really be split up into two device nodes, but that's a job for
-	 * another day.
-	 */
-	zr->video_dev->vfl_dir = VFL_DIR_M2M;
-
-	zoran_queue_init(zr, &zr->vq);
-
-	err = video_register_device(zr->video_dev, VFL_TYPE_VIDEO, video_nr[zr->id]);
-	if (err < 0)
+	err = zoran_init_video_devices(zr);
+	if (err)
 		goto exit_statcomb;
-	video_set_drvdata(zr->video_dev, zr);
 
 	zoran_init_hardware(zr);
 	if (!pass_through) {
@@ -931,9 +954,6 @@
 	dma_free_coherent(&zr->pci_dev->dev, BUZ_NUM_STAT_COM * sizeof(u32) * 2, zr->stat_comb, zr->p_scb);
 exit_statcom:
 	dma_free_coherent(&zr->pci_dev->dev, BUZ_NUM_STAT_COM * sizeof(u32), zr->stat_com, zr->p_sc);
-exit_video:
-	kfree(zr->video_dev);
-exit:
 	return err;
 }
 
@@ -965,7 +985,7 @@
 	dma_free_coherent(&zr->pci_dev->dev, BUZ_NUM_STAT_COM * sizeof(u32) * 2, zr->stat_comb, zr->p_scb);
 	pci_release_regions(pdev);
 	pci_disable_device(zr->pci_dev);
-	video_unregister_device(zr->video_dev);
+	zoran_exit_video_devices(zr);
 exit_free:
 	v4l2_ctrl_handler_free(&zr->hdl);
 	v4l2_device_unregister(&zr->v4l2_dev);
@@ -1069,8 +1089,10 @@
 
 	err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
 	if (err)
-		return -ENODEV;
-	vb2_dma_contig_set_max_seg_size(&pdev->dev, DMA_BIT_MASK(32));
+		return err;
+	err = vb2_dma_contig_set_max_seg_size(&pdev->dev, U32_MAX);
+	if (err)
+		return err;
 
 	nr = zoran_num++;
 	if (nr >= BUZ_MAX) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/zoran/zoran_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/zoran/zoran_device.c
@@ -814,7 +814,7 @@
 		if (zr->jpg_settings.tmp_dcm == 1)
 			i = (zr->jpg_dma_tail - zr->jpg_err_shift) & BUZ_MASK_STAT_COM;
 		else
-			i = ((zr->jpg_dma_tail - zr->jpg_err_shift) & 1) * 2 + 1;
+			i = ((zr->jpg_dma_tail - zr->jpg_err_shift) & 1) * 2;
 
 		stat_com = le32_to_cpu(zr->stat_com[i]);
 		if ((stat_com & 1) == 0) {
@@ -826,6 +826,11 @@
 		size = (stat_com & GENMASK(22, 1)) >> 1;
 
 		buf = zr->inuse[i];
+		if (!buf) {
+			spin_unlock_irqrestore(&zr->queued_bufs_lock, flags);
+			pci_err(zr->pci_dev, "No buffer at slot %d\n", i);
+			return;
+		}
 		buf->vbuf.vb2_buf.timestamp = ktime_get_ns();
 
 		if (zr->codec_mode == BUZ_MODE_MOTION_COMPRESS) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/media/zoran/zoran_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/media/zoran/zoran_driver.c
@@ -255,8 +255,6 @@
 	strscpy(cap->card, ZR_DEVNAME(zr), sizeof(cap->card));
 	strscpy(cap->driver, "zoran", sizeof(cap->driver));
 	snprintf(cap->bus_info, sizeof(cap->bus_info), "PCI:%s", pci_name(zr->pci_dev));
-	cap->device_caps = zr->video_dev->device_caps;
-	cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
 	return 0;
 }
 
@@ -582,6 +580,9 @@
 	struct zoran *zr = video_drvdata(file);
 	int res = 0;
 
+	if (zr->norm == std)
+		return 0;
+
 	if (zr->running != ZORAN_MAP_MODE_NONE)
 		return -EBUSY;
 
@@ -739,6 +740,7 @@
 	if (parm->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
 		return -EINVAL;
 
+	parm->parm.capture.readbuffers = 9;
 	return 0;
 }
 
@@ -869,6 +871,10 @@
 		vbuf = &buf->vbuf;
 
 		buf->vbuf.field = V4L2_FIELD_INTERLACED;
+		if (BUZ_MAX_HEIGHT < (zr->v4l_settings.height * 2))
+			buf->vbuf.field = V4L2_FIELD_INTERLACED;
+		else
+			buf->vbuf.field = V4L2_FIELD_TOP;
 		vb2_set_plane_payload(&buf->vbuf.vb2_buf, 0, zr->buffer_size);
 		vb2_buffer_done(&buf->vbuf.vb2_buf, VB2_BUF_STATE_DONE);
 		zr->inuse[0] = NULL;
@@ -928,6 +934,7 @@
 		zr->stat_com[j] = cpu_to_le32(1);
 		zr->inuse[j] = NULL;
 	}
+	zr->vbseq = 0;
 
 	if (zr->map_mode != ZORAN_MAP_MODE_RAW) {
 		pci_info(zr->pci_dev, "START JPG\n");
@@ -1008,7 +1015,7 @@
 	.wait_finish            = vb2_ops_wait_finish,
 };
 
-int zoran_queue_init(struct zoran *zr, struct vb2_queue *vq)
+int zoran_queue_init(struct zoran *zr, struct vb2_queue *vq, int dir)
 {
 	int err;
 
@@ -1016,8 +1023,9 @@
 	INIT_LIST_HEAD(&zr->queued_bufs);
 
 	vq->dev = &zr->pci_dev->dev;
-	vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
-	vq->io_modes = VB2_USERPTR | VB2_DMABUF | VB2_MMAP | VB2_READ | VB2_WRITE;
+	vq->type = dir;
+
+	vq->io_modes = VB2_DMABUF | VB2_MMAP | VB2_READ | VB2_WRITE;
 	vq->drv_priv = zr;
 	vq->buf_struct_size = sizeof(struct zr_buffer);
 	vq->ops = &zr_video_qops;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/most/dim2/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/most/dim2/Makefile
@@ -1,4 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_MOST_DIM2) += most_dim2.o
 
-most_dim2-objs := dim2.o hal.o sysfs.o
+most_dim2-objs := dim2.o hal.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/most/dim2/dim2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/most/dim2/dim2.c
@@ -117,7 +117,8 @@
 	(((p)[1] == 0x18) && ((p)[2] == 0x05) && ((p)[3] == 0x0C) && \
 	 ((p)[13] == 0x3C) && ((p)[14] == 0x00) && ((p)[15] == 0x0A))
 
-bool dim2_sysfs_get_state_cb(void)
+static ssize_t state_show(struct device *dev, struct device_attribute *attr,
+			  char *buf)
 {
 	bool state;
 	unsigned long flags;
@@ -126,9 +127,18 @@
 	state = dim_get_lock_state();
 	spin_unlock_irqrestore(&dim_lock, flags);
 
-	return state;
+	return sysfs_emit(buf, "%s\n", state ? "locked" : "");
 }
 
+static DEVICE_ATTR_RO(state);
+
+static struct attribute *dim2_attrs[] = {
+	&dev_attr_state.attr,
+	NULL,
+};
+
+ATTRIBUTE_GROUPS(dim2);
+
 /**
  * dimcb_on_error - callback from HAL to report miscommunication between
  * HDM and HAL
@@ -716,6 +726,23 @@
 	return -EINVAL;
 }
 
+static void dim2_release(struct device *d)
+{
+	struct dim2_hdm *dev = container_of(d, struct dim2_hdm, dev);
+	unsigned long flags;
+
+	kthread_stop(dev->netinfo_task);
+
+	spin_lock_irqsave(&dim_lock, flags);
+	dim_shutdown();
+	spin_unlock_irqrestore(&dim_lock, flags);
+
+	if (dev->disable_platform)
+		dev->disable_platform(to_platform_device(d->parent));
+
+	kfree(dev);
+}
+
 /*
  * dim2_probe - dim2 probe handler
  * @pdev: platform device structure
@@ -736,7 +763,7 @@
 
 	enum { MLB_INT_IDX, AHB0_INT_IDX };
 
-	dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
 	if (!dev)
 		return -ENOMEM;
 
@@ -748,25 +775,27 @@
 				      "microchip,clock-speed", &clock_speed);
 	if (ret) {
 		dev_err(&pdev->dev, "missing dt property clock-speed\n");
-		return ret;
+		goto err_free_dev;
 	}
 
 	ret = get_dim2_clk_speed(clock_speed, &dev->clk_speed);
 	if (ret) {
 		dev_err(&pdev->dev, "bad dt property clock-speed\n");
-		return ret;
+		goto err_free_dev;
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dev->io_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(dev->io_base))
-		return PTR_ERR(dev->io_base);
+	if (IS_ERR(dev->io_base)) {
+		ret = PTR_ERR(dev->io_base);
+		goto err_free_dev;
+	}
 
 	of_id = of_match_node(dim2_of_match, pdev->dev.of_node);
 	pdata = of_id->data;
 	ret = pdata && pdata->enable ? pdata->enable(pdev) : 0;
 	if (ret)
-		return ret;
+		goto err_free_dev;
 
 	dev->disable_platform = pdata ? pdata->disable : NULL;
 
@@ -857,32 +886,19 @@
 	dev->most_iface.request_netinfo = request_netinfo;
 	dev->most_iface.driver_dev = &pdev->dev;
 	dev->most_iface.dev = &dev->dev;
-	dev->dev.init_name = "dim2_state";
+	dev->dev.init_name = dev->name;
 	dev->dev.parent = &pdev->dev;
+	dev->dev.release = dim2_release;
 
-	ret = most_register_interface(&dev->most_iface);
-	if (ret) {
-		dev_err(&pdev->dev, "failed to register MOST interface\n");
-		goto err_stop_thread;
-	}
-
-	ret = dim2_sysfs_probe(&dev->dev);
-	if (ret) {
-		dev_err(&pdev->dev, "failed to create sysfs attribute\n");
-		goto err_unreg_iface;
-	}
-
-	return 0;
+	return most_register_interface(&dev->most_iface);
 
-err_unreg_iface:
-	most_deregister_interface(&dev->most_iface);
-err_stop_thread:
-	kthread_stop(dev->netinfo_task);
 err_shutdown_dim:
 	dim_shutdown();
 err_disable_platform:
 	if (dev->disable_platform)
 		dev->disable_platform(pdev);
+err_free_dev:
+	kfree(dev);
 
 	return ret;
 }
@@ -896,18 +912,8 @@
 static int dim2_remove(struct platform_device *pdev)
 {
 	struct dim2_hdm *dev = platform_get_drvdata(pdev);
-	unsigned long flags;
 
-	dim2_sysfs_destroy(&dev->dev);
 	most_deregister_interface(&dev->most_iface);
-	kthread_stop(dev->netinfo_task);
-
-	spin_lock_irqsave(&dim_lock, flags);
-	dim_shutdown();
-	spin_unlock_irqrestore(&dim_lock, flags);
-
-	if (dev->disable_platform)
-		dev->disable_platform(pdev);
 
 	return 0;
 }
@@ -1082,6 +1088,7 @@
 	.driver = {
 		.name = "hdm_dim2",
 		.of_match_table = dim2_of_match,
+		.dev_groups = dim2_groups,
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/most/dim2/sysfs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/most/dim2/sysfs.h
@@ -16,15 +16,4 @@
 	struct kobject kobj_group;
 };
 
-struct device;
-
-int dim2_sysfs_probe(struct device *dev);
-void dim2_sysfs_destroy(struct device *dev);
-
-/*
- * callback,
- * must deliver MediaLB state as true if locked or false if unlocked
- */
-bool dim2_sysfs_get_state_cb(void);
-
 #endif	/* DIM2_SYSFS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/mt7621-dts/gbpc1.dts
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/mt7621-dts/gbpc1.dts
@@ -11,14 +11,15 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x0 0x1c000000>, <0x20000000 0x4000000>;
+		reg = <0x00000000 0x1c000000>,
+		      <0x20000000 0x04000000>;
 	};
 
 	chosen {
 		bootargs = "console=ttyS0,57600";
 	};
 
-	palmbus: palmbus@1E000000 {
+	palmbus: palmbus@1e000000 {
 		i2c@900 {
 			status = "okay";
 		};
@@ -37,24 +38,16 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		system {
-			label = "gb-pc1:green:system";
+		power {
+			label = "green:power";
 			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
 		};
 
-		status {
-			label = "gb-pc1:green:status";
+		system {
+			label = "green:system";
 			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
-		};
-
-		lan1 {
-			label = "gb-pc1:green:lan1";
-			gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
-		};
-
-		lan2 {
-			label = "gb-pc1:green:lan2";
-			gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
 		};
 	};
 };
@@ -94,9 +87,8 @@
 
 		partition@50000 {
 			label = "firmware";
-			reg = <0x50000 0x1FB0000>;
+			reg = <0x50000 0x1fb0000>;
 		};
-
 	};
 };
 
@@ -105,9 +97,12 @@
 };
 
 &pinctrl {
-	state_default: pinctrl0 {
-		default_gpio: gpio {
-			groups = "wdt", "rgmii2", "uart3";
+	pinctrl-names = "default";
+	pinctrl-0 = <&state_default>;
+
+	state_default: state-default {
+		gpio-pinmux {
+			groups = "rgmii2", "uart3", "wdt";
 			function = "gpio";
 		};
 	};
@@ -116,12 +111,13 @@
 &switch0 {
 	ports {
 		port@0 {
+			status = "okay";
 			label = "ethblack";
-			status = "ok";
 		};
+
 		port@4 {
+			status = "okay";
 			label = "ethblue";
-			status = "ok";
 		};
 	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/mt7621-dts/gbpc2.dts
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/mt7621-dts/gbpc2.dts
@@ -1,21 +1,121 @@
 /dts-v1/;
 
-#include "gbpc1.dts"
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	compatible = "gnubee,gb-pc2", "mediatek,mt7621-soc";
 	model = "GB-PC2";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x1c000000>,
+		      <0x20000000 0x04000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	palmbus: palmbus@1e000000 {
+		i2c@900 {
+			status = "okay";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&sdhci {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		broken-flash-reset;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+
+		partition@30000 {
+			label = "u-boot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+
+		factory: partition@40000 {
+			label = "factory";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+
+		partition@50000 {
+			label = "firmware";
+			reg = <0x50000 0x1fb0000>;
+		};
+	};
 };
 
-&default_gpio {
-	groups = "wdt", "uart3";
-	function = "gpio";
+&pcie {
+	status = "okay";
 };
 
-&gmac1 {
-	status = "ok";
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&state_default>;
+
+	state_default: state-default {
+		gpio-pinmux {
+			groups = "wdt";
+			function = "gpio";
+		};
+	};
 };
 
-&phy_external {
-	status = "ok";
+&ethernet {
+	gmac1: mac@1 {
+		status = "okay";
+		phy-handle = <&ethphy7>;
+	};
+
+	mdio-bus {
+		ethphy7: ethernet-phy@7 {
+			reg = <7>;
+			phy-mode = "rgmii-rxid";
+		};
+	};
+};
+
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "ethblack";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "ethblue";
+		};
+	};
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/mt7621-dts/mt7621.dtsi
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/mt7621-dts/mt7621.dtsi
@@ -36,9 +36,9 @@
 		regulator-max-microvolt = <3300000>;
 		enable-active-high;
 		regulator-always-on;
-	  };
+	};
 
-	  mmc_fixed_1v8_io: fixedregulator@1 {
+	mmc_fixed_1v8_io: fixedregulator@1 {
 		compatible = "regulator-fixed";
 		regulator-name = "mmc_io";
 		regulator-min-microvolt = <1800000>;
@@ -47,10 +47,10 @@
 		regulator-always-on;
 	};
 
-	palmbus: palmbus@1E000000 {
+	palmbus: palmbus@1e000000 {
 		compatible = "palmbus";
-		reg = <0x1E000000 0x100000>;
-		ranges = <0x0 0x1E000000 0x0FFFFF>;
+		reg = <0x1e000000 0x100000>;
+		ranges = <0x0 0x1e000000 0x0fffff>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -301,11 +301,11 @@
 		#reset-cells = <1>;
 	};
 
-	sdhci: sdhci@1E130000 {
+	sdhci: sdhci@1e130000 {
 		status = "disabled";
 
 		compatible = "mediatek,mt7620-mmc";
-		reg = <0x1E130000 0x4000>;
+		reg = <0x1e130000 0x4000>;
 
 		bus-width = <4>;
 		max-frequency = <48000000>;
@@ -327,7 +327,7 @@
 		interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	xhci: xhci@1E1C0000 {
+	xhci: xhci@1e1c0000 {
 		status = "okay";
 
 		compatible = "mediatek,mt8173-xhci";
@@ -391,37 +391,32 @@
 
 		mediatek,ethsys = <&sysc>;
 
+		pinctrl-names = "default";
+		pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>, <&rgmii2_pins>;
 
 		gmac0: mac@0 {
 			compatible = "mediatek,eth-mac";
 			reg = <0>;
 			phy-mode = "rgmii";
+
 			fixed-link {
 				speed = <1000>;
 				full-duplex;
 				pause;
 			};
 		};
+
 		gmac1: mac@1 {
 			compatible = "mediatek,eth-mac";
 			reg = <1>;
 			status = "off";
 			phy-mode = "rgmii-rxid";
-			phy-handle = <&phy_external>;
 		};
+
 		mdio-bus {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			phy_external: ethernet-phy@5 {
-				status = "off";
-				reg = <5>;
-				phy-mode = "rgmii-rxid";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&rgmii2_pins>;
-			};
-
 			switch0: switch0@0 {
 				compatible = "mediatek,mt7621";
 				#address-cells = <1>;
@@ -439,36 +434,43 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 					reg = <0>;
+
 					port@0 {
 						status = "off";
 						reg = <0>;
 						label = "lan0";
 					};
+
 					port@1 {
 						status = "off";
 						reg = <1>;
 						label = "lan1";
 					};
+
 					port@2 {
 						status = "off";
 						reg = <2>;
 						label = "lan2";
 					};
+
 					port@3 {
 						status = "off";
 						reg = <3>;
 						label = "lan3";
 					};
+
 					port@4 {
 						status = "off";
 						reg = <4>;
 						label = "lan4";
 					};
+
 					port@6 {
 						reg = <6>;
 						label = "cpu";
 						ethernet = <&gmac0>;
 						phy-mode = "trgmii";
+
 						fixed-link {
 							speed = <1000>;
 							full-duplex;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/mt7621-pci/pci-mt7621.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/mt7621-pci/pci-mt7621.c
@@ -93,8 +93,8 @@
  * reset lines are inverted.
  */
 struct mt7621_pcie {
-	void __iomem *base;
 	struct device *dev;
+	void __iomem *base;
 	struct list_head ports;
 	bool resets_inverted;
 };
@@ -129,7 +129,7 @@
 	writel_relaxed(val, port->base + reg);
 }
 
-static inline u32 mt7621_pci_get_cfgaddr(unsigned int bus, unsigned int slot,
+static inline u32 mt7621_pcie_get_cfgaddr(unsigned int bus, unsigned int slot,
 					 unsigned int func, unsigned int where)
 {
 	return (((where & 0xF00) >> 8) << 24) | (bus << 16) | (slot << 11) |
@@ -140,7 +140,7 @@
 					 unsigned int devfn, int where)
 {
 	struct mt7621_pcie *pcie = bus->sysdata;
-	u32 address = mt7621_pci_get_cfgaddr(bus->number, PCI_SLOT(devfn),
+	u32 address = mt7621_pcie_get_cfgaddr(bus->number, PCI_SLOT(devfn),
 					     PCI_FUNC(devfn), where);
 
 	writel_relaxed(address, pcie->base + RALINK_PCI_CONFIG_ADDR);
@@ -148,7 +148,7 @@
 	return pcie->base + RALINK_PCI_CONFIG_DATA + (where & 3);
 }
 
-struct pci_ops mt7621_pci_ops = {
+struct pci_ops mt7621_pcie_ops = {
 	.map_bus	= mt7621_pcie_map_bus,
 	.read		= pci_generic_config_read,
 	.write		= pci_generic_config_write,
@@ -156,7 +156,7 @@
 
 static u32 read_config(struct mt7621_pcie *pcie, unsigned int dev, u32 reg)
 {
-	u32 address = mt7621_pci_get_cfgaddr(0, dev, 0, reg);
+	u32 address = mt7621_pcie_get_cfgaddr(0, dev, 0, reg);
 
 	pcie_write(pcie, address, RALINK_PCI_CONFIG_ADDR);
 	return pcie_read(pcie, RALINK_PCI_CONFIG_DATA);
@@ -165,7 +165,7 @@
 static void write_config(struct mt7621_pcie *pcie, unsigned int dev,
 			 u32 reg, u32 val)
 {
-	u32 address = mt7621_pci_get_cfgaddr(0, dev, 0, reg);
+	u32 address = mt7621_pcie_get_cfgaddr(0, dev, 0, reg);
 
 	pcie_write(pcie, address, RALINK_PCI_CONFIG_ADDR);
 	pcie_write(pcie, val, RALINK_PCI_CONFIG_DATA);
@@ -505,16 +505,17 @@
 {
 	struct mt7621_pcie *pcie = pci_host_bridge_priv(host);
 
-	host->ops = &mt7621_pci_ops;
+	host->ops = &mt7621_pcie_ops;
 	host->sysdata = pcie;
 	return pci_host_probe(host);
 }
 
-static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
-	{ .soc_id = "mt7621", .revision = "E2" }
+static const struct soc_device_attribute mt7621_pcie_quirks_match[] = {
+	{ .soc_id = "mt7621", .revision = "E2" },
+	{ /* sentinel */ }
 };
 
-static int mt7621_pci_probe(struct platform_device *pdev)
+static int mt7621_pcie_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	const struct soc_device_attribute *attr;
@@ -535,7 +536,7 @@
 	platform_set_drvdata(pdev, pcie);
 	INIT_LIST_HEAD(&pcie->ports);
 
-	attr = soc_device_match(mt7621_pci_quirks_match);
+	attr = soc_device_match(mt7621_pcie_quirks_match);
 	if (attr)
 		pcie->resets_inverted = true;
 
@@ -572,7 +573,7 @@
 	return err;
 }
 
-static int mt7621_pci_remove(struct platform_device *pdev)
+static int mt7621_pcie_remove(struct platform_device *pdev)
 {
 	struct mt7621_pcie *pcie = platform_get_drvdata(pdev);
 	struct mt7621_pcie_port *port;
@@ -583,18 +584,18 @@
 	return 0;
 }
 
-static const struct of_device_id mt7621_pci_ids[] = {
+static const struct of_device_id mt7621_pcie_ids[] = {
 	{ .compatible = "mediatek,mt7621-pci" },
 	{},
 };
-MODULE_DEVICE_TABLE(of, mt7621_pci_ids);
+MODULE_DEVICE_TABLE(of, mt7621_pcie_ids);
 
-static struct platform_driver mt7621_pci_driver = {
-	.probe = mt7621_pci_probe,
-	.remove = mt7621_pci_remove,
+static struct platform_driver mt7621_pcie_driver = {
+	.probe = mt7621_pcie_probe,
+	.remove = mt7621_pcie_remove,
 	.driver = {
 		.name = "mt7621-pci",
-		.of_match_table = of_match_ptr(mt7621_pci_ids),
+		.of_match_table = of_match_ptr(mt7621_pcie_ids),
 	},
 };
-builtin_platform_driver(mt7621_pci_driver);
+builtin_platform_driver(mt7621_pcie_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/core/rtw_led.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/core/rtw_led.c
@@ -74,6 +74,7 @@
 	_cancel_workitem_sync(&pLed->BlinkWorkItem);
 	_cancel_timer_ex(&pLed->BlinkTimer);
 	ResetLedStatus(pLed);
+	SwLedOff(pLed->padapter, pLed);
 }
 
 /*  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/core/rtw_mlme.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/core/rtw_mlme.c
@@ -1722,6 +1722,8 @@
 		psetkeyparm->grpkey = 1;
 		break;
 	default:
+		kfree(psetkeyparm);
+		kfree(pcmd);
 		res = _FAIL;
 		goto exit;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/core/rtw_mlme_ext.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/core/rtw_mlme_ext.c
@@ -104,6 +104,7 @@
 	{0x01},	/* 0x10, RT_CHANNEL_DOMAIN_JAPAN */
 	{0x02},	/* 0x11, RT_CHANNEL_DOMAIN_FCC_NO_DFS */
 	{0x01},	/* 0x12, RT_CHANNEL_DOMAIN_JAPAN_NO_DFS */
+	{0x00}, /* 0x13 */
 	{0x02},	/* 0x14, RT_CHANNEL_DOMAIN_TAIWAN_NO_DFS */
 	{0x00},	/* 0x15, RT_CHANNEL_DOMAIN_ETSI_NO_DFS */
 	{0x00},	/* 0x16, RT_CHANNEL_DOMAIN_KOREA_NO_DFS */
@@ -115,6 +116,7 @@
 	{0x00},	/* 0x1C, */
 	{0x00},	/* 0x1D, */
 	{0x00},	/* 0x1E, */
+	{0x00},	/* 0x1F, */
 	/*  0x20 ~ 0x7F , New Define ===== */
 	{0x00},	/* 0x20, RT_CHANNEL_DOMAIN_WORLD_NULL */
 	{0x01},	/* 0x21, RT_CHANNEL_DOMAIN_ETSI1_NULL */
@@ -7080,12 +7082,12 @@
 	struct mlme_ext_priv		*pmlmeext = &padapter->mlmeextpriv;
 	struct cmd_priv *pcmdpriv = &padapter->cmdpriv;
 
-	pcmd_obj = kzalloc(sizeof(struct cmd_obj), GFP_KERNEL);
+	pcmd_obj = kzalloc(sizeof(*pcmd_obj), GFP_ATOMIC);
 	if (!pcmd_obj)
 		return;
 
 	cmdsz = (sizeof(struct stadel_event) + sizeof(struct C2HEvent_Header));
-	pevtcmd = kzalloc(cmdsz, GFP_KERNEL);
+	pevtcmd = kzalloc(cmdsz, GFP_ATOMIC);
 	if (!pevtcmd) {
 		kfree(pcmd_obj);
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/core/rtw_recv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/core/rtw_recv.c
@@ -1942,8 +1942,7 @@
 		struct recv_frame *pending_frame;
 		int cnt = 0;
 
-		pending_frame = rtw_alloc_recvframe(&padapter->recvpriv.uc_swdec_pending_queue);
-		while (pending_frame) {
+		while ((pending_frame = rtw_alloc_recvframe(&padapter->recvpriv.uc_swdec_pending_queue))) {
 			cnt++;
 			recv_func_posthandle(padapter, pending_frame);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/core/rtw_xmit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/core/rtw_xmit.c
@@ -179,7 +179,11 @@
 
 	pxmitpriv->free_xmit_extbuf_cnt = num_xmit_extbuf;
 
-	rtw_alloc_hwxmits(padapter);
+	if (rtw_alloc_hwxmits(padapter)) {
+		res = _FAIL;
+		goto exit;
+	}
+
 	rtw_init_hwxmits(pxmitpriv->hwxmits, pxmitpriv->hwxmit_entry);
 
 	for (i = 0; i < 4; i++)
@@ -1516,7 +1520,7 @@
 	return res;
 }
 
-void rtw_alloc_hwxmits(struct adapter *padapter)
+int rtw_alloc_hwxmits(struct adapter *padapter)
 {
 	struct hw_xmit *hwxmits;
 	struct xmit_priv *pxmitpriv = &padapter->xmitpriv;
@@ -1524,22 +1528,17 @@
 	pxmitpriv->hwxmit_entry = HWXMIT_ENTRY;
 
 	pxmitpriv->hwxmits = kzalloc(sizeof(struct hw_xmit) * pxmitpriv->hwxmit_entry, GFP_KERNEL);
+	if (!pxmitpriv->hwxmits)
+		return -ENOMEM;
 
 	hwxmits = pxmitpriv->hwxmits;
 
-	if (pxmitpriv->hwxmit_entry == 5) {
-		hwxmits[0] .sta_queue = &pxmitpriv->bm_pending;
-		hwxmits[1] .sta_queue = &pxmitpriv->vo_pending;
-		hwxmits[2] .sta_queue = &pxmitpriv->vi_pending;
-		hwxmits[3] .sta_queue = &pxmitpriv->bk_pending;
-		hwxmits[4] .sta_queue = &pxmitpriv->be_pending;
-	} else if (pxmitpriv->hwxmit_entry == 4) {
-		hwxmits[0] .sta_queue = &pxmitpriv->vo_pending;
-		hwxmits[1] .sta_queue = &pxmitpriv->vi_pending;
-		hwxmits[2] .sta_queue = &pxmitpriv->be_pending;
-		hwxmits[3] .sta_queue = &pxmitpriv->bk_pending;
-	} else {
-	}
+	hwxmits[0].sta_queue = &pxmitpriv->vo_pending;
+	hwxmits[1].sta_queue = &pxmitpriv->vi_pending;
+	hwxmits[2].sta_queue = &pxmitpriv->be_pending;
+	hwxmits[3].sta_queue = &pxmitpriv->bk_pending;
+
+	return 0;
 }
 
 void rtw_free_hwxmits(struct adapter *padapter)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/hal/rtl8188e_hal_init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/hal/rtl8188e_hal_init.c
@@ -572,10 +572,10 @@
 	}
 	memcpy(pFirmware->szFwBuffer, fw->data, fw->size);
 	pFirmware->ulFwLength = fw->size;
-	release_firmware(fw);
-	DBG_88E_LEVEL(_drv_info_, "+%s: !bUsedWoWLANFw, FmrmwareLen:%d+\n", __func__, pFirmware->ulFwLength);
+	dev_dbg(device, "!bUsedWoWLANFw, FmrmwareLen:%d+\n", pFirmware->ulFwLength);
 
 Exit:
+	release_firmware(fw);
 	return rtStatus;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/include/rtw_xmit.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/include/rtw_xmit.h
@@ -345,7 +345,7 @@
 void rtw_init_hwxmits(struct hw_xmit *phwxmit, int entry);
 s32 _rtw_init_xmit_priv(struct xmit_priv *pxmitpriv, struct adapter *padapter);
 void _rtw_free_xmit_priv(struct xmit_priv *pxmitpriv);
-void rtw_alloc_hwxmits(struct adapter *padapter);
+int rtw_alloc_hwxmits(struct adapter *padapter);
 void rtw_free_hwxmits(struct adapter *padapter);
 s32 rtw_xmit(struct adapter *padapter, struct sk_buff **pkt);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/os_dep/ioctl_linux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/os_dep/ioctl_linux.c
@@ -465,12 +465,11 @@
 
 		if (wep_key_len > 0) {
 			wep_key_len = wep_key_len <= 5 ? 5 : 13;
-			wep_total_len = wep_key_len + FIELD_OFFSET(struct ndis_802_11_wep, KeyMaterial);
-			pwep = kmalloc(wep_total_len, GFP_KERNEL);
+			wep_total_len = wep_key_len + sizeof(*pwep);
+			pwep = kzalloc(wep_total_len, GFP_KERNEL);
 			if (!pwep)
 				goto exit;
 
-			memset(pwep, 0, wep_total_len);
 			pwep->KeyLength = wep_key_len;
 			pwep->Length = wep_total_len;
 			if (wep_key_len == 13) {
@@ -1249,9 +1248,11 @@
 						break;
 					}
 					sec_len = *(pos++); len -= 1;
-					if (sec_len > 0 && sec_len <= len) {
+					if (sec_len > 0 &&
+					    sec_len <= len &&
+					    sec_len <= 32) {
 						ssid[ssid_index].SsidLength = sec_len;
-						memcpy(ssid[ssid_index].Ssid, pos, ssid[ssid_index].SsidLength);
+						memcpy(ssid[ssid_index].Ssid, pos, sec_len);
 						ssid_index++;
 					}
 					pos += sec_len;
@@ -1978,7 +1979,7 @@
 	struct ieee_param *param = NULL;
 	struct iw_point *pencoding = &wrqu->encoding;
 	struct iw_encode_ext *pext = (struct iw_encode_ext *)extra;
-	int ret = 0;
+	int ret = -1;
 
 	param_len = sizeof(struct ieee_param) + pext->key_len;
 	param = kzalloc(param_len, GFP_KERNEL);
@@ -2004,7 +2005,7 @@
 		alg_name = "CCMP";
 		break;
 	default:
-		return -1;
+		goto out;
 	}
 
 	strncpy((char *)param->u.crypt.alg, alg_name, IEEE_CRYPT_ALG_NAME_LEN);
@@ -2031,6 +2032,7 @@
 
 	ret =  wpa_set_encryption(dev, param, param_len);
 
+out:
 	kfree(param);
 	return ret;
 }
@@ -2049,93 +2051,6 @@
 	return 0;
 }
 
-static int rtw_wx_read32(struct net_device *dev,
-			    struct iw_request_info *info,
-			    union iwreq_data *wrqu, char *extra)
-{
-	struct adapter *padapter;
-	struct iw_point *p;
-	u16 len;
-	u32 addr;
-	u32 data32;
-	u32 bytes;
-	u8 *ptmp;
-
-	padapter = (struct adapter *)rtw_netdev_priv(dev);
-	p = &wrqu->data;
-	len = p->length;
-	ptmp = kmalloc(len, GFP_KERNEL);
-	if (!ptmp)
-		return -ENOMEM;
-
-	if (copy_from_user(ptmp, p->pointer, len)) {
-		kfree(ptmp);
-		return -EFAULT;
-	}
-
-	bytes = 0;
-	addr = 0;
-	sscanf(ptmp, "%d,%x", &bytes, &addr);
-
-	switch (bytes) {
-	case 1:
-		data32 = rtw_read8(padapter, addr);
-		sprintf(extra, "0x%02X", data32);
-		break;
-	case 2:
-		data32 = rtw_read16(padapter, addr);
-		sprintf(extra, "0x%04X", data32);
-		break;
-	case 4:
-		data32 = rtw_read32(padapter, addr);
-		sprintf(extra, "0x%08X", data32);
-		break;
-	default:
-		DBG_88E(KERN_INFO "%s: usage> read [bytes],[address(hex)]\n", __func__);
-		return -EINVAL;
-	}
-	DBG_88E(KERN_INFO "%s: addr = 0x%08X data =%s\n", __func__, addr, extra);
-
-	kfree(ptmp);
-	return 0;
-}
-
-static int rtw_wx_write32(struct net_device *dev,
-			    struct iw_request_info *info,
-			    union iwreq_data *wrqu, char *extra)
-{
-	struct adapter *padapter = (struct adapter *)rtw_netdev_priv(dev);
-
-	u32 addr;
-	u32 data32;
-	u32 bytes;
-
-	bytes = 0;
-	addr = 0;
-	data32 = 0;
-	sscanf(extra, "%d,%x,%x", &bytes, &addr, &data32);
-
-	switch (bytes) {
-	case 1:
-		rtw_write8(padapter, addr, (u8)data32);
-		DBG_88E(KERN_INFO "%s: addr = 0x%08X data = 0x%02X\n", __func__, addr, (u8)data32);
-		break;
-	case 2:
-		rtw_write16(padapter, addr, (u16)data32);
-		DBG_88E(KERN_INFO "%s: addr = 0x%08X data = 0x%04X\n", __func__, addr, (u16)data32);
-		break;
-	case 4:
-		rtw_write32(padapter, addr, data32);
-		DBG_88E(KERN_INFO "%s: addr = 0x%08X data = 0x%08X\n", __func__, addr, data32);
-		break;
-	default:
-		DBG_88E(KERN_INFO "%s: usage> write [bytes],[address(hex)],[data(hex)]\n", __func__);
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
 static int rtw_wx_read_rf(struct net_device *dev,
 			    struct iw_request_info *info,
 			    union iwreq_data *wrqu, char *extra)
@@ -6570,8 +6485,8 @@
 };
 
 static iw_handler rtw_private_handler[] = {
-rtw_wx_write32,				/* 0x00 */
-rtw_wx_read32,				/* 0x01 */
+	NULL,				/* 0x00 */
+	NULL,				/* 0x01 */
 rtw_drvext_hdl,				/* 0x02 */
 rtw_mp_ioctl_hdl,			/* 0x03 */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/os_dep/mlme_linux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/os_dep/mlme_linux.c
@@ -114,7 +114,7 @@
 
 	buff = NULL;
 	if (authmode == _WPA_IE_ID_) {
-		buff = kzalloc(IW_CUSTOM_MAX, GFP_KERNEL);
+		buff = kzalloc(IW_CUSTOM_MAX, GFP_ATOMIC);
 		if (!buff)
 			return;
 		p = buff;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/os_dep/os_intfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/os_dep/os_intfs.c
@@ -17,6 +17,7 @@
 MODULE_DESCRIPTION("Realtek Wireless Lan Driver");
 MODULE_AUTHOR("Realtek Semiconductor Corp.");
 MODULE_VERSION(DRIVERVERSION);
+MODULE_FIRMWARE("rtlwifi/rtl8188eufw.bin");
 
 #define CONFIG_BR_EXT_BRNAME "br0"
 #define RTW_NOTCH_FILTER 0 /* 0:Disable, 1:Enable, */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/r8188eu/os_dep/usb_intf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/r8188eu/os_dep/usb_intf.c
@@ -30,7 +30,7 @@
 	/*=== Realtek demoboard ===*/
 	{USB_DEVICE(USB_VENDER_ID_REALTEK, 0x8179)}, /* 8188EUS */
 	{USB_DEVICE(USB_VENDER_ID_REALTEK, 0x0179)}, /* 8188ETV */
-	{USB_DEVICE(USB_VENDER_ID_REALTEK, 0xf179)}, /* 8188FU */
+	{USB_DEVICE(USB_VENDER_ID_REALTEK, 0xffef)}, /* Rosewill USB-N150 Nano */
 	/*=== Customer ID ===*/
 	/****** 8188EUS ********/
 	{USB_DEVICE(0x07B8, 0x8179)}, /* Abocom - Abocom */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192e/rtl8192e/rtl_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192e/rtl8192e/rtl_core.c
@@ -768,6 +768,7 @@
 	else
 		netif_wake_queue(dev);
 
+	priv->bfirst_after_down = false;
 	return 0;
 }
 
@@ -2549,13 +2550,14 @@
 			free_irq(dev->irq, dev);
 			priv->irq = 0;
 		}
-		free_rtllib(dev);
 
 		if (dev->mem_start != 0) {
 			iounmap((void __iomem *)dev->mem_start);
 			release_mem_region(pci_resource_start(pdev, 1),
 					pci_resource_len(pdev, 1));
 		}
+
+		free_rtllib(dev);
 	}
 
 	pci_disable_device(pdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192e/rtl8192e/rtl_dm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192e/rtl8192e/rtl_dm.c
@@ -185,7 +185,6 @@
 static void _rtl92e_dm_deinit_fsync(struct net_device *dev);
 
 static	void _rtl92e_dm_check_txrateandretrycount(struct net_device *dev);
-static  void _rtl92e_dm_check_ac_dc_power(struct net_device *dev);
 static void _rtl92e_dm_check_fsync(struct net_device *dev);
 static void _rtl92e_dm_check_rf_ctrl_gpio(void *data);
 static void _rtl92e_dm_fsync_timer_callback(struct timer_list *t);
@@ -238,8 +237,6 @@
 	if (priv->being_init_adapter)
 		return;
 
-	_rtl92e_dm_check_ac_dc_power(dev);
-
 	_rtl92e_dm_check_txrateandretrycount(dev);
 	_rtl92e_dm_check_edca_turbo(dev);
 
@@ -257,30 +254,6 @@
 	_rtl92e_dm_cts_to_self(dev);
 }
 
-static void _rtl92e_dm_check_ac_dc_power(struct net_device *dev)
-{
-	struct r8192_priv *priv = rtllib_priv(dev);
-	static const char ac_dc_script[] = "/etc/acpi/wireless-rtl-ac-dc-power.sh";
-	char *argv[] = {(char *)ac_dc_script, DRV_NAME, NULL};
-	static char *envp[] = {"HOME=/",
-			"TERM=linux",
-			"PATH=/usr/bin:/bin",
-			 NULL};
-
-	if (priv->ResetProgress == RESET_TYPE_SILENT) {
-		RT_TRACE((COMP_INIT | COMP_POWER | COMP_RF),
-			 "GPIOChangeRFWorkItemCallBack(): Silent Reset!!!!!!!\n");
-		return;
-	}
-
-	if (priv->rtllib->state != RTLLIB_LINKED)
-		return;
-	call_usermodehelper(ac_dc_script, argv, envp, UMH_WAIT_PROC);
-
-	return;
-};
-
-
 void rtl92e_init_adaptive_rate(struct net_device *dev)
 {
 
@@ -1800,10 +1773,6 @@
 	u8 tmp1byte;
 	enum rt_rf_power_state eRfPowerStateToSet;
 	bool bActuallySet = false;
-	char *argv[3];
-	static const char RadioPowerPath[] = "/etc/acpi/events/RadioPower.sh";
-	static char *envp[] = {"HOME=/", "TERM=linux", "PATH=/usr/bin:/bin",
-			       NULL};
 
 	bActuallySet = false;
 
@@ -1835,14 +1804,6 @@
 		mdelay(1000);
 		priv->bHwRfOffAction = 1;
 		rtl92e_set_rf_state(dev, eRfPowerStateToSet, RF_CHANGE_BY_HW);
-		if (priv->bHwRadioOff)
-			argv[1] = "RFOFF";
-		else
-			argv[1] = "RFON";
-
-		argv[0] = (char *)RadioPowerPath;
-		argv[2] = NULL;
-		call_usermodehelper(RadioPowerPath, argv, envp, UMH_WAIT_PROC);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192e/rtllib.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192e/rtllib.h
@@ -1980,7 +1980,7 @@
 void rtllib_softmac_xmit(struct rtllib_txb *txb, struct rtllib_device *ieee);
 
 void rtllib_start_ibss(struct rtllib_device *ieee);
-void rtllib_softmac_init(struct rtllib_device *ieee);
+int rtllib_softmac_init(struct rtllib_device *ieee);
 void rtllib_softmac_free(struct rtllib_device *ieee);
 void rtllib_disassociate(struct rtllib_device *ieee);
 void rtllib_stop_scan(struct rtllib_device *ieee);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192e/rtllib_module.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192e/rtllib_module.c
@@ -88,7 +88,7 @@
 	err = rtllib_networks_allocate(ieee);
 	if (err) {
 		pr_err("Unable to allocate beacon storage: %d\n", err);
-		goto failed;
+		goto free_netdev;
 	}
 	rtllib_networks_initialize(ieee);
 
@@ -121,11 +121,13 @@
 	ieee->hwsec_active = 0;
 
 	memset(ieee->swcamtable, 0, sizeof(struct sw_cam_table) * 32);
-	rtllib_softmac_init(ieee);
+	err = rtllib_softmac_init(ieee);
+	if (err)
+		goto free_crypt_info;
 
 	ieee->pHTInfo = kzalloc(sizeof(struct rt_hi_throughput), GFP_KERNEL);
 	if (!ieee->pHTInfo)
-		return NULL;
+		goto free_softmac;
 
 	HTUpdateDefaultSetting(ieee);
 	HTInitializeHTInfo(ieee);
@@ -141,8 +143,14 @@
 
 	return dev;
 
- failed:
+free_softmac:
+	rtllib_softmac_free(ieee);
+free_crypt_info:
+	lib80211_crypt_info_free(&ieee->crypt_info);
+	rtllib_networks_free(ieee);
+free_netdev:
 	free_netdev(dev);
+
 	return NULL;
 }
 EXPORT_SYMBOL(alloc_rtllib);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192e/rtllib_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192e/rtllib_rx.c
@@ -1489,9 +1489,9 @@
 		hdrlen += 4;
 	}
 
-	rtllib_monitor_rx(ieee, skb, rx_stats, hdrlen);
 	ieee->stats.rx_packets++;
 	ieee->stats.rx_bytes += skb->len;
+	rtllib_monitor_rx(ieee, skb, rx_stats, hdrlen);
 
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192e/rtllib_softmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192e/rtllib_softmac.c
@@ -651,9 +651,9 @@
 	spin_lock_irqsave(&ieee->beacon_lock, flags);
 
 	ieee->beacon_txing = 0;
-	del_timer_sync(&ieee->beacon_timer);
 
 	spin_unlock_irqrestore(&ieee->beacon_lock, flags);
+	del_timer_sync(&ieee->beacon_timer);
 
 }
 
@@ -2952,7 +2952,7 @@
 	}
 }
 
-void rtllib_softmac_init(struct rtllib_device *ieee)
+int rtllib_softmac_init(struct rtllib_device *ieee)
 {
 	int i;
 
@@ -2963,7 +2963,8 @@
 		ieee->seq_ctrl[i] = 0;
 	ieee->dot11d_info = kzalloc(sizeof(struct rt_dot11d_info), GFP_ATOMIC);
 	if (!ieee->dot11d_info)
-		netdev_err(ieee->dev, "Can't alloc memory for DOT11D\n");
+		return -ENOMEM;
+
 	ieee->LinkDetectInfo.SlotIndex = 0;
 	ieee->LinkDetectInfo.SlotNum = 2;
 	ieee->LinkDetectInfo.NumRecvBcnInPeriod = 0;
@@ -3029,6 +3030,7 @@
 
 	tasklet_setup(&ieee->ps_task, rtllib_sta_ps);
 
+	return 0;
 }
 
 void rtllib_softmac_free(struct rtllib_device *ieee)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192u/ieee80211/ieee80211_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192u/ieee80211/ieee80211_rx.c
@@ -951,9 +951,11 @@
 #endif
 
 	if (ieee->iw_mode == IW_MODE_MONITOR) {
+		unsigned int len = skb->len;
+
 		ieee80211_monitor_rx(ieee, skb, rx_stats);
 		stats->rx_packets++;
-		stats->rx_bytes += skb->len;
+		stats->rx_bytes += len;
 		return 1;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192u/ieee80211/ieee80211_softmac.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192u/ieee80211/ieee80211_softmac.c
@@ -528,9 +528,9 @@
 	spin_lock_irqsave(&ieee->beacon_lock, flags);
 
 	ieee->beacon_txing = 0;
-	del_timer_sync(&ieee->beacon_timer);
 
 	spin_unlock_irqrestore(&ieee->beacon_lock, flags);
+	del_timer_sync(&ieee->beacon_timer);
 }
 
 void ieee80211_stop_send_beacons(struct ieee80211_device *ieee)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192u/r8192U.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192u/r8192U.h
@@ -1013,7 +1013,7 @@
 	bool		bis_any_nonbepkts;
 	bool		bcurrent_turbo_EDCA;
 	bool		bis_cur_rdlstate;
-	struct timer_list fsync_timer;
+	struct delayed_work fsync_work;
 	bool bfsync_processing;	/* 500ms Fsync timer is active or not */
 	u32	rate_record;
 	u32	rateCountDiffRecord;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192u/r8192U_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192u/r8192U_core.c
@@ -229,7 +229,7 @@
 
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
-				 indx | 0xfe00, 0, usbdata, 1, HZ / 2);
+				 indx | 0xfe00, 0, usbdata, 1, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -251,7 +251,7 @@
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 indx | 0xfe00, 0, usbdata, 1, HZ / 2);
+				 indx | 0xfe00, 0, usbdata, 1, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -279,7 +279,7 @@
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 1, HZ / 2);
+				 usbdata, 1, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -305,7 +305,7 @@
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 2, HZ / 2);
+				 usbdata, 2, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -331,7 +331,7 @@
 	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
 				 RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 4, HZ / 2);
+				 usbdata, 4, 500);
 	kfree(usbdata);
 
 	if (status < 0) {
@@ -355,7 +355,7 @@
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 1, HZ / 2);
+				 usbdata, 1, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -380,7 +380,7 @@
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 2, HZ / 2);
+				 usbdata, 2, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -404,7 +404,7 @@
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 indx | 0xfe00, 0, usbdata, 2, HZ / 2);
+				 indx | 0xfe00, 0, usbdata, 2, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
@@ -430,7 +430,7 @@
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx & 0xff) | 0xff00, (indx >> 8) & 0x0f,
-				 usbdata, 4, HZ / 2);
+				 usbdata, 4, 500);
 	*data = *usbdata;
 	kfree(usbdata);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192u/r8192U_dm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192u/r8192U_dm.c
@@ -2578,19 +2578,20 @@
 	priv->ieee80211->fsync_seconddiff_ratethreshold = 200;
 	priv->ieee80211->fsync_state = Default_Fsync;
 	priv->framesyncMonitor = 1;	/* current default 0xc38 monitor on */
-	timer_setup(&priv->fsync_timer, dm_fsync_timer_callback, 0);
+	INIT_DELAYED_WORK(&priv->fsync_work, dm_fsync_work_callback);
 }
 
 static void dm_deInit_fsync(struct net_device *dev)
 {
 	struct r8192_priv *priv = ieee80211_priv(dev);
 
-	del_timer_sync(&priv->fsync_timer);
+	cancel_delayed_work_sync(&priv->fsync_work);
 }
 
-void dm_fsync_timer_callback(struct timer_list *t)
+void dm_fsync_work_callback(struct work_struct *work)
 {
-	struct r8192_priv *priv = from_timer(priv, t, fsync_timer);
+	struct r8192_priv *priv =
+	    container_of(work, struct r8192_priv, fsync_work.work);
 	struct net_device *dev = priv->ieee80211->dev;
 	u32 rate_index, rate_count = 0, rate_count_diff = 0;
 	bool		bSwitchFromCountDiff = false;
@@ -2657,17 +2658,16 @@
 			}
 		}
 		if (bDoubleTimeInterval) {
-			if (timer_pending(&priv->fsync_timer))
-				del_timer_sync(&priv->fsync_timer);
-			priv->fsync_timer.expires = jiffies +
-				msecs_to_jiffies(priv->ieee80211->fsync_time_interval*priv->ieee80211->fsync_multiple_timeinterval);
-			add_timer(&priv->fsync_timer);
+			cancel_delayed_work_sync(&priv->fsync_work);
+			schedule_delayed_work(&priv->fsync_work,
+					      msecs_to_jiffies(priv
+					      ->ieee80211->fsync_time_interval *
+					      priv->ieee80211->fsync_multiple_timeinterval));
 		} else {
-			if (timer_pending(&priv->fsync_timer))
-				del_timer_sync(&priv->fsync_timer);
-			priv->fsync_timer.expires = jiffies +
-				msecs_to_jiffies(priv->ieee80211->fsync_time_interval);
-			add_timer(&priv->fsync_timer);
+			cancel_delayed_work_sync(&priv->fsync_work);
+			schedule_delayed_work(&priv->fsync_work,
+					      msecs_to_jiffies(priv
+					      ->ieee80211->fsync_time_interval));
 		}
 	} else {
 		/* Let Register return to default value; */
@@ -2695,7 +2695,7 @@
 	struct r8192_priv *priv = ieee80211_priv(dev);
 
 	RT_TRACE(COMP_HALDM, "%s\n", __func__);
-	del_timer_sync(&(priv->fsync_timer));
+	cancel_delayed_work_sync(&priv->fsync_work);
 
 	/* Let Register return to default value; */
 	if (priv->bswitch_fsync) {
@@ -2736,11 +2736,9 @@
 		if (priv->ieee80211->fsync_rate_bitmap &  rateBitmap)
 			priv->rate_record += priv->stats.received_rate_histogram[1][rateIndex];
 	}
-	if (timer_pending(&priv->fsync_timer))
-		del_timer_sync(&priv->fsync_timer);
-	priv->fsync_timer.expires = jiffies +
-			msecs_to_jiffies(priv->ieee80211->fsync_time_interval);
-	add_timer(&priv->fsync_timer);
+	cancel_delayed_work_sync(&priv->fsync_work);
+	schedule_delayed_work(&priv->fsync_work,
+			      msecs_to_jiffies(priv->ieee80211->fsync_time_interval));
 
 	write_nic_dword(dev, rOFDM0_RxDetector2, 0x465c12cd);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8192u/r8192U_dm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8192u/r8192U_dm.h
@@ -166,7 +166,7 @@
 void dm_init_edca_turbo(struct net_device *dev);
 void dm_rf_operation_test_callback(unsigned long data);
 void dm_rf_pathcheck_workitemcallback(struct work_struct *work);
-void dm_fsync_timer_callback(struct timer_list *t);
+void dm_fsync_work_callback(struct work_struct *work);
 void dm_cck_txpower_adjust(struct net_device *dev, bool  binch14);
 void dm_shadow_init(struct net_device *dev);
 void dm_initialize_txpower_tracking(struct net_device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/os_intfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/os_intfs.c
@@ -323,6 +323,7 @@
 	mp871xinit(padapter);
 	init_default_value(padapter);
 	r8712_InitSwLeds(padapter);
+	mutex_init(&padapter->mutex_start);
 	return ret;
 }
 
@@ -332,7 +333,6 @@
 	r8712_free_evt_priv(&padapter->evtpriv);
 	r8712_DeInitSwLeds(padapter);
 	r8712_free_mlme_priv(&padapter->mlmepriv);
-	r8712_free_io_queue(padapter);
 	_free_xmit_priv(&padapter->xmitpriv);
 	_r8712_free_sta_priv(&padapter->stapriv);
 	_r8712_free_recv_priv(&padapter->recvpriv);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/rtl8712_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/rtl8712_cmd.c
@@ -117,34 +117,6 @@
 	kfree(pdrvcmd->pbuf);
 }
 
-static u8 read_macreg_hdl(struct _adapter *padapter, u8 *pbuf)
-{
-	void (*pcmd_callback)(struct _adapter *dev, struct cmd_obj	*pcmd);
-	struct cmd_obj *pcmd  = (struct cmd_obj *)pbuf;
-
-	/*  invoke cmd->callback function */
-	pcmd_callback = cmd_callback[pcmd->cmdcode].callback;
-	if (!pcmd_callback)
-		r8712_free_cmd_obj(pcmd);
-	else
-		pcmd_callback(padapter, pcmd);
-	return H2C_SUCCESS;
-}
-
-static u8 write_macreg_hdl(struct _adapter *padapter, u8 *pbuf)
-{
-	void (*pcmd_callback)(struct _adapter *dev, struct cmd_obj	*pcmd);
-	struct cmd_obj *pcmd  = (struct cmd_obj *)pbuf;
-
-	/*  invoke cmd->callback function */
-	pcmd_callback = cmd_callback[pcmd->cmdcode].callback;
-	if (!pcmd_callback)
-		r8712_free_cmd_obj(pcmd);
-	else
-		pcmd_callback(padapter, pcmd);
-	return H2C_SUCCESS;
-}
-
 static u8 read_bbreg_hdl(struct _adapter *padapter, u8 *pbuf)
 {
 	struct cmd_obj *pcmd  = (struct cmd_obj *)pbuf;
@@ -213,14 +185,6 @@
 	pcmd_r = NULL;
 
 	switch (pcmd->cmdcode) {
-	case GEN_CMD_CODE(_Read_MACREG):
-		read_macreg_hdl(padapter, (u8 *)pcmd);
-		pcmd_r = pcmd;
-		break;
-	case GEN_CMD_CODE(_Write_MACREG):
-		write_macreg_hdl(padapter, (u8 *)pcmd);
-		pcmd_r = pcmd;
-		break;
 	case GEN_CMD_CODE(_Read_BBREG):
 		read_bbreg_hdl(padapter, (u8 *)pcmd);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/rtl871x_xmit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/rtl871x_xmit.c
@@ -21,6 +21,7 @@
 #include "osdep_intf.h"
 #include "usb_ops.h"
 
+#include <linux/usb.h>
 #include <linux/ieee80211.h>
 
 static const u8 P802_1H_OUI[P80211_OUI_LEN] = {0x00, 0x00, 0xf8};
@@ -55,6 +56,7 @@
 	sint i;
 	struct xmit_buf *pxmitbuf;
 	struct xmit_frame *pxframe;
+	int j;
 
 	memset((unsigned char *)pxmitpriv, 0, sizeof(struct xmit_priv));
 	spin_lock_init(&pxmitpriv->lock);
@@ -117,11 +119,8 @@
 	_init_queue(&pxmitpriv->pending_xmitbuf_queue);
 	pxmitpriv->pallocated_xmitbuf =
 		kmalloc(NR_XMITBUFF * sizeof(struct xmit_buf) + 4, GFP_ATOMIC);
-	if (!pxmitpriv->pallocated_xmitbuf) {
-		kfree(pxmitpriv->pallocated_frame_buf);
-		pxmitpriv->pallocated_frame_buf = NULL;
-		return -ENOMEM;
-	}
+	if (!pxmitpriv->pallocated_xmitbuf)
+		goto clean_up_frame_buf;
 	pxmitpriv->pxmitbuf = pxmitpriv->pallocated_xmitbuf + 4 -
 			      ((addr_t)(pxmitpriv->pallocated_xmitbuf) & 3);
 	pxmitbuf = (struct xmit_buf *)pxmitpriv->pxmitbuf;
@@ -129,13 +128,17 @@
 		INIT_LIST_HEAD(&pxmitbuf->list);
 		pxmitbuf->pallocated_buf =
 			kmalloc(MAX_XMITBUF_SZ + XMITBUF_ALIGN_SZ, GFP_ATOMIC);
-		if (!pxmitbuf->pallocated_buf)
-			return -ENOMEM;
+		if (!pxmitbuf->pallocated_buf) {
+			j = 0;
+			goto clean_up_alloc_buf;
+		}
 		pxmitbuf->pbuf = pxmitbuf->pallocated_buf + XMITBUF_ALIGN_SZ -
 				 ((addr_t) (pxmitbuf->pallocated_buf) &
 				 (XMITBUF_ALIGN_SZ - 1));
-		if (r8712_xmit_resource_alloc(padapter, pxmitbuf))
-			return -ENOMEM;
+		if (r8712_xmit_resource_alloc(padapter, pxmitbuf)) {
+			j = 1;
+			goto clean_up_alloc_buf;
+		}
 		list_add_tail(&pxmitbuf->list,
 				 &(pxmitpriv->free_xmitbuf_queue.queue));
 		pxmitbuf++;
@@ -146,6 +149,28 @@
 	init_hwxmits(pxmitpriv->hwxmits, pxmitpriv->hwxmit_entry);
 	tasklet_setup(&pxmitpriv->xmit_tasklet, r8712_xmit_bh);
 	return 0;
+
+clean_up_alloc_buf:
+	if (j) {
+		/* failure happened in r8712_xmit_resource_alloc()
+		 * delete extra pxmitbuf->pallocated_buf
+		 */
+		kfree(pxmitbuf->pallocated_buf);
+	}
+	for (j = 0; j < i; j++) {
+		int k;
+
+		pxmitbuf--;			/* reset pointer */
+		kfree(pxmitbuf->pallocated_buf);
+		for (k = 0; k < 8; k++)		/* delete xmit urb's */
+			usb_free_urb(pxmitbuf->pxmit_urb[k]);
+	}
+	kfree(pxmitpriv->pallocated_xmitbuf);
+	pxmitpriv->pallocated_xmitbuf = NULL;
+clean_up_frame_buf:
+	kfree(pxmitpriv->pallocated_frame_buf);
+	pxmitpriv->pallocated_frame_buf = NULL;
+	return -ENOMEM;
 }
 
 void _free_xmit_priv(struct xmit_priv *pxmitpriv)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/usb_intf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/usb_intf.c
@@ -265,6 +265,7 @@
 
 static void r8712_usb_dvobj_deinit(struct _adapter *padapter)
 {
+	r8712_free_io_queue(padapter);
 }
 
 void rtl871x_intf_stop(struct _adapter *padapter)
@@ -302,9 +303,6 @@
 			rtl8712_hal_deinit(padapter);
 		}
 
-		/*s6.*/
-		if (padapter->dvobj_deinit)
-			padapter->dvobj_deinit(padapter);
 		padapter->bup = false;
 	}
 }
@@ -538,13 +536,13 @@
 		} else {
 			AutoloadFail = false;
 		}
-		if (((mac[0] == 0xff) && (mac[1] == 0xff) &&
+		if ((!AutoloadFail) ||
+		    ((mac[0] == 0xff) && (mac[1] == 0xff) &&
 		     (mac[2] == 0xff) && (mac[3] == 0xff) &&
 		     (mac[4] == 0xff) && (mac[5] == 0xff)) ||
 		    ((mac[0] == 0x00) && (mac[1] == 0x00) &&
 		     (mac[2] == 0x00) && (mac[3] == 0x00) &&
-		     (mac[4] == 0x00) && (mac[5] == 0x00)) ||
-		     (!AutoloadFail)) {
+		     (mac[4] == 0x00) && (mac[5] == 0x00))) {
 			mac[0] = 0x00;
 			mac[1] = 0xe0;
 			mac[2] = 0x4c;
@@ -569,7 +567,6 @@
 	if (rtl871x_load_fw(padapter))
 		goto deinit_drv_sw;
 	spin_lock_init(&padapter->lock_rx_ff0_filter);
-	mutex_init(&padapter->mutex_start);
 	return 0;
 
 deinit_drv_sw:
@@ -595,18 +592,20 @@
 
 	/* never exit with a firmware callback pending */
 	wait_for_completion(&padapter->rtl8712_fw_ready);
+	if (pnetdev->reg_state != NETREG_UNINITIALIZED)
+		unregister_netdev(pnetdev); /* will call netdev_close() */
 	usb_set_intfdata(pusb_intf, NULL);
 	release_firmware(padapter->fw);
 	if (drvpriv.drv_registered)
 		padapter->surprise_removed = true;
-	if (pnetdev->reg_state != NETREG_UNINITIALIZED)
-		unregister_netdev(pnetdev); /* will call netdev_close() */
 	r8712_flush_rwctrl_works(padapter);
 	r8712_flush_led_works(padapter);
 	udelay(1);
 	/* Stop driver mlme relation timer */
 	r8712_stop_drv_timers(padapter);
 	r871x_dev_unload(padapter);
+	if (padapter->dvobj_deinit)
+		padapter->dvobj_deinit(padapter);
 	r8712_free_drv_sw(padapter);
 	free_netdev(pnetdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/usb_ops.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/usb_ops.c
@@ -29,7 +29,8 @@
 	u16 wvalue;
 	u16 index;
 	u16 len;
-	__le32 data;
+	int status;
+	__le32 data = 0;
 	struct intf_priv *intfpriv = intfhdl->pintfpriv;
 
 	request = 0x05;
@@ -37,8 +38,10 @@
 	index = 0;
 	wvalue = (u16)(addr & 0x0000ffff);
 	len = 1;
-	r8712_usbctrl_vendorreq(intfpriv, request, wvalue, index, &data, len,
-				requesttype);
+	status = r8712_usbctrl_vendorreq(intfpriv, request, wvalue, index,
+					 &data, len, requesttype);
+	if (status < 0)
+		return 0;
 	return (u8)(le32_to_cpu(data) & 0x0ff);
 }
 
@@ -49,7 +52,8 @@
 	u16 wvalue;
 	u16 index;
 	u16 len;
-	__le32 data;
+	int status;
+	__le32 data = 0;
 	struct intf_priv *intfpriv = intfhdl->pintfpriv;
 
 	request = 0x05;
@@ -57,8 +61,10 @@
 	index = 0;
 	wvalue = (u16)(addr & 0x0000ffff);
 	len = 2;
-	r8712_usbctrl_vendorreq(intfpriv, request, wvalue, index, &data, len,
-				requesttype);
+	status = r8712_usbctrl_vendorreq(intfpriv, request, wvalue, index,
+					 &data, len, requesttype);
+	if (status < 0)
+		return 0;
 	return (u16)(le32_to_cpu(data) & 0xffff);
 }
 
@@ -69,7 +75,8 @@
 	u16 wvalue;
 	u16 index;
 	u16 len;
-	__le32 data;
+	int status;
+	__le32 data = 0;
 	struct intf_priv *intfpriv = intfhdl->pintfpriv;
 
 	request = 0x05;
@@ -77,8 +84,10 @@
 	index = 0;
 	wvalue = (u16)(addr & 0x0000ffff);
 	len = 4;
-	r8712_usbctrl_vendorreq(intfpriv, request, wvalue, index, &data, len,
-				requesttype);
+	status = r8712_usbctrl_vendorreq(intfpriv, request, wvalue, index,
+					 &data, len, requesttype);
+	if (status < 0)
+		return 0;
 	return le32_to_cpu(data);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/usb_ops_linux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/usb_ops_linux.c
@@ -494,7 +494,7 @@
 		memcpy(pIo_buf, pdata, len);
 	}
 	status = usb_control_msg(udev, pipe, request, reqtype, value, index,
-				 pIo_buf, len, HZ / 2);
+				 pIo_buf, len, 500);
 	if (status > 0) {  /* Success this control transfer. */
 		if (requesttype == 0x01) {
 			/* For Control read transfer, we have to copy the read
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8712/xmit_linux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8712/xmit_linux.c
@@ -118,6 +118,12 @@
 	for (i = 0; i < 8; i++) {
 		pxmitbuf->pxmit_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
 		if (!pxmitbuf->pxmit_urb[i]) {
+			int k;
+
+			for (k = i - 1; k >= 0; k--) {
+				/* handle allocation errors part way through loop */
+				usb_free_urb(pxmitbuf->pxmit_urb[k]);
+			}
 			netdev_err(padapter->pnetdev, "pxmitbuf->pxmit_urb[i] == NULL\n");
 			return -ENOMEM;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_ap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_ap.c
@@ -891,7 +891,7 @@
 		&ie_len,
 		(pbss_network->ie_length - _BEACON_IE_OFFSET_)
 	);
-	if (p !=  NULL) {
+	if (p) {
 		memcpy(supportRate, p + 2, ie_len);
 		supportRateNum = ie_len;
 	}
@@ -903,7 +903,7 @@
 		&ie_len,
 		pbss_network->ie_length - _BEACON_IE_OFFSET_
 	);
-	if (p !=  NULL) {
+	if (p) {
 		memcpy(supportRate + supportRateNum, p + 2, ie_len);
 		supportRateNum += ie_len;
 	}
@@ -991,7 +991,7 @@
 			break;
 		}
 
-		if ((p == NULL) || (ie_len == 0))
+		if (!p || ie_len == 0)
 			break;
 	}
 
@@ -1021,7 +1021,7 @@
 				break;
 			}
 
-			if ((p == NULL) || (ie_len == 0))
+			if (!p || ie_len == 0)
 				break;
 		}
 	}
@@ -1145,7 +1145,7 @@
 	psta = rtw_get_stainfo(&padapter->stapriv, pbss_network->mac_address);
 	if (!psta) {
 		psta = rtw_alloc_stainfo(&padapter->stapriv, pbss_network->mac_address);
-		if (psta == NULL)
+		if (!psta)
 			return _FAIL;
 	}
 
@@ -1275,7 +1275,7 @@
 	}
 
 	psetstakey_para = rtw_zmalloc(sizeof(struct set_stakey_parm));
-	if (psetstakey_para == NULL) {
+	if (!psetstakey_para) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1311,12 +1311,12 @@
 	int res = _SUCCESS;
 
 	pcmd = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (pcmd == NULL) {
+	if (!pcmd) {
 		res = _FAIL;
 		goto exit;
 	}
 	psetkeyparm = rtw_zmalloc(sizeof(struct setkey_parm));
-	if (psetkeyparm == NULL) {
+	if (!psetkeyparm) {
 		kfree(pcmd);
 		res = _FAIL;
 		goto exit;
@@ -1474,11 +1474,11 @@
 		&wps_ielen
 	);
 
-	if (pwps_ie == NULL || wps_ielen == 0)
+	if (!pwps_ie || wps_ielen == 0)
 		return;
 
 	pwps_ie_src = pmlmepriv->wps_beacon_ie;
-	if (pwps_ie_src == NULL)
+	if (!pwps_ie_src)
 		return;
 
 	wps_offset = (uint)(pwps_ie - ie);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_cmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_cmd.c
@@ -161,8 +161,6 @@
 
 int rtw_init_cmd_priv(struct	cmd_priv *pcmdpriv)
 {
-	int res = 0;
-
 	init_completion(&pcmdpriv->cmd_queue_comp);
 	init_completion(&pcmdpriv->terminate_cmdthread_comp);
 
@@ -174,18 +172,16 @@
 
 	pcmdpriv->cmd_allocated_buf = rtw_zmalloc(MAX_CMDSZ + CMDBUFF_ALIGN_SZ);
 
-	if (!pcmdpriv->cmd_allocated_buf) {
-		res = -ENOMEM;
-		goto exit;
-	}
+	if (!pcmdpriv->cmd_allocated_buf)
+		return -ENOMEM;
 
 	pcmdpriv->cmd_buf = pcmdpriv->cmd_allocated_buf  +  CMDBUFF_ALIGN_SZ - ((SIZE_PTR)(pcmdpriv->cmd_allocated_buf) & (CMDBUFF_ALIGN_SZ-1));
 
 	pcmdpriv->rsp_allocated_buf = rtw_zmalloc(MAX_RSPSZ + 4);
 
 	if (!pcmdpriv->rsp_allocated_buf) {
-		res = -ENOMEM;
-		goto exit;
+		kfree(pcmdpriv->cmd_allocated_buf);
+		return -ENOMEM;
 	}
 
 	pcmdpriv->rsp_buf = pcmdpriv->rsp_allocated_buf  +  4 - ((SIZE_PTR)(pcmdpriv->rsp_allocated_buf) & 3);
@@ -195,8 +191,8 @@
 	pcmdpriv->rsp_cnt = 0;
 
 	mutex_init(&pcmdpriv->sctx_mutex);
-exit:
-	return res;
+
+	return 0;
 }
 
 static void c2h_wk_callback(struct work_struct *work);
@@ -255,7 +251,7 @@
 {
 	unsigned long irqL;
 
-	if (obj == NULL)
+	if (!obj)
 		goto exit;
 
 	/* spin_lock_bh(&queue->lock); */
@@ -323,7 +319,7 @@
 	int res = _FAIL;
 	struct adapter *padapter = pcmdpriv->padapter;
 
-	if (cmd_obj == NULL)
+	if (!cmd_obj)
 		goto exit;
 
 	cmd_obj->padapter = padapter;
@@ -488,7 +484,7 @@
 		/* call callback function for post-processed */
 		if (pcmd->cmdcode < ARRAY_SIZE(rtw_cmd_callback)) {
 			pcmd_callback = rtw_cmd_callback[pcmd->cmdcode].callback;
-			if (pcmd_callback == NULL) {
+			if (!pcmd_callback) {
 				rtw_free_cmd_obj(pcmd);
 			} else {
 				/* todo: !!! fill rsp_buf to pcmd->rsp if (pcmd->rsp!= NULL) */
@@ -507,7 +503,7 @@
 	/*  free all cmd_obj resources */
 	do {
 		pcmd = rtw_dequeue_cmd(pcmdpriv);
-		if (pcmd == NULL) {
+		if (!pcmd) {
 			rtw_unregister_cmd_alive(padapter);
 			break;
 		}
@@ -546,11 +542,11 @@
 		rtw_lps_ctrl_wk_cmd(padapter, LPS_CTRL_SCAN, 1);
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL)
+	if (!ph2c)
 		return _FAIL;
 
 	psurveyPara = rtw_zmalloc(sizeof(struct sitesurvey_parm));
-	if (psurveyPara == NULL) {
+	if (!psurveyPara) {
 		kfree(ph2c);
 		return _FAIL;
 	}
@@ -608,13 +604,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pbsetdataratepara = rtw_zmalloc(sizeof(struct setdatarate_parm));
-	if (pbsetdataratepara == NULL) {
+	if (!pbsetdataratepara) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -644,7 +640,7 @@
 	u8 res = _SUCCESS;
 
 	pcmd = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (pcmd == NULL) {
+	if (!pcmd) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -677,7 +673,7 @@
 	} else {
 		/* need enqueue, prepare cmd_obj and enqueue */
 		pcmd = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (pcmd == NULL) {
+		if (!pcmd) {
 			res = _FAIL;
 			goto exit;
 		}
@@ -729,7 +725,7 @@
 	u8 *ptmp = NULL;
 
 	pcmd = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (pcmd == NULL) {
+	if (!pcmd) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -841,7 +837,7 @@
 
 	/* prepare cmd parameter */
 	param = rtw_zmalloc(sizeof(*param));
-	if (param == NULL) {
+	if (!param) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -850,7 +846,7 @@
 	if (enqueue) {
 		/* need enqueue, prepare cmd_obj and enqueue */
 		cmdobj = rtw_zmalloc(sizeof(*cmdobj));
-		if (cmdobj == NULL) {
+		if (!cmdobj) {
 			res = _FAIL;
 			kfree(param);
 			goto exit;
@@ -878,7 +874,7 @@
 
 	psetop = rtw_zmalloc(sizeof(struct setopmode_parm));
 
-	if (psetop == NULL) {
+	if (!psetop) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -886,7 +882,7 @@
 
 	if (enqueue) {
 		ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (ph2c == NULL) {
+		if (!ph2c) {
 			kfree(psetop);
 			res = _FAIL;
 			goto exit;
@@ -914,7 +910,7 @@
 	u8 res = _SUCCESS;
 
 	psetstakey_para = rtw_zmalloc(sizeof(struct set_stakey_parm));
-	if (psetstakey_para == NULL) {
+	if (!psetstakey_para) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -936,14 +932,14 @@
 
 	if (enqueue) {
 		ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (ph2c == NULL) {
+		if (!ph2c) {
 			kfree(psetstakey_para);
 			res = _FAIL;
 			goto exit;
 		}
 
 		psetstakey_rsp = rtw_zmalloc(sizeof(struct set_stakey_rsp));
-		if (psetstakey_rsp == NULL) {
+		if (!psetstakey_rsp) {
 			kfree(ph2c);
 			kfree(psetstakey_para);
 			res = _FAIL;
@@ -981,20 +977,20 @@
 		}
 	} else {
 		ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (ph2c == NULL) {
+		if (!ph2c) {
 			res = _FAIL;
 			goto exit;
 		}
 
 		psetstakey_para = rtw_zmalloc(sizeof(struct set_stakey_parm));
-		if (psetstakey_para == NULL) {
+		if (!psetstakey_para) {
 			kfree(ph2c);
 			res = _FAIL;
 			goto exit;
 		}
 
 		psetstakey_rsp = rtw_zmalloc(sizeof(struct set_stakey_rsp));
-		if (psetstakey_rsp == NULL) {
+		if (!psetstakey_rsp) {
 			kfree(ph2c);
 			kfree(psetstakey_para);
 			res = _FAIL;
@@ -1026,13 +1022,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	paddbareq_parm = rtw_zmalloc(sizeof(struct addBaReq_parm));
-	if (paddbareq_parm == NULL) {
+	if (!paddbareq_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1058,13 +1054,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1093,13 +1089,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1129,13 +1125,13 @@
 
 	/* only  primary padapter does this cmd */
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1177,7 +1173,7 @@
 
 	/* prepare cmd parameter */
 	setChannelPlan_param = rtw_zmalloc(sizeof(struct SetChannelPlan_param));
-	if (setChannelPlan_param == NULL) {
+	if (!setChannelPlan_param) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -1186,7 +1182,7 @@
 	if (enqueue) {
 		/* need enqueue, prepare cmd_obj and enqueue */
 		pcmdobj = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (pcmdobj == NULL) {
+		if (!pcmdobj) {
 			kfree(setChannelPlan_param);
 			res = _FAIL;
 			goto exit;
@@ -1436,13 +1432,13 @@
 
 	if (enqueue) {
 		ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (ph2c == NULL) {
+		if (!ph2c) {
 			res = _FAIL;
 			goto exit;
 		}
 
 		pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-		if (pdrvextra_cmd_parm == NULL) {
+		if (!pdrvextra_cmd_parm) {
 			kfree(ph2c);
 			res = _FAIL;
 			goto exit;
@@ -1478,13 +1474,13 @@
 
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1544,13 +1540,13 @@
 
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1579,13 +1575,13 @@
 	u8 res = _SUCCESS;
 
 	ppscmd = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ppscmd == NULL) {
+	if (!ppscmd) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ppscmd);
 		res = _FAIL;
 		goto exit;
@@ -1651,13 +1647,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1745,13 +1741,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1780,13 +1776,13 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	pdrvextra_cmd_parm = rtw_zmalloc(sizeof(struct drvextra_cmd_parm));
-	if (pdrvextra_cmd_parm == NULL) {
+	if (!pdrvextra_cmd_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -1961,7 +1957,7 @@
 	struct wlan_bssid_ex *pnetwork = (struct wlan_bssid_ex *)pcmd->parmbuf;
 	struct wlan_network *tgt_network = &(pmlmepriv->cur_network);
 
-	if (pcmd->parmbuf == NULL)
+	if (!pcmd->parmbuf)
 		goto exit;
 
 	if (pcmd->res != H2C_SUCCESS)
@@ -1984,9 +1980,9 @@
 	} else {
 		pwlan = rtw_alloc_network(pmlmepriv);
 		spin_lock_bh(&(pmlmepriv->scanned_queue.lock));
-		if (pwlan == NULL) {
+		if (!pwlan) {
 			pwlan = rtw_get_oldest_wlan_network(&pmlmepriv->scanned_queue);
-			if (pwlan == NULL) {
+			if (!pwlan) {
 				spin_unlock_bh(&(pmlmepriv->scanned_queue.lock));
 				goto createbss_cmd_fail;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_ioctl_set.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_ioctl_set.c
@@ -370,7 +370,7 @@
 	struct	mlme_priv 	*pmlmepriv = &padapter->mlmepriv;
 	u8 res = true;
 
-	if (padapter == NULL) {
+	if (!padapter) {
 		res = false;
 		goto exit;
 	}
@@ -481,7 +481,7 @@
 		return 0;
 
 	psta = rtw_get_stainfo(&adapter->stapriv, get_bssid(pmlmepriv));
-	if (psta == NULL)
+	if (!psta)
 		return 0;
 
 	short_GI = query_ra_short_GI(psta);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_mlme.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_mlme.c
@@ -439,7 +439,7 @@
 		pwlan = list_entry(plist, struct wlan_network, list);
 
 		if (!pwlan->fixed) {
-			if (oldest == NULL || time_after(oldest->last_scanned, pwlan->last_scanned))
+			if (!oldest || time_after(oldest->last_scanned, pwlan->last_scanned))
 				oldest = pwlan;
 		}
 	}
@@ -542,7 +542,7 @@
 			/* TODO: don't select network in the same ess as oldest if it's new enough*/
 		}
 
-		if (oldest == NULL || time_after(oldest->last_scanned, pnetwork->last_scanned))
+		if (!oldest || time_after(oldest->last_scanned, pnetwork->last_scanned))
 			oldest = pnetwork;
 
 	}
@@ -749,7 +749,9 @@
 	}
 
 	if (check_fwstate(pmlmepriv, _FW_UNDER_SURVEY)) {
+		spin_unlock_bh(&pmlmepriv->lock);
 		del_timer_sync(&pmlmepriv->scan_to_timer);
+		spin_lock_bh(&pmlmepriv->lock);
 		_clr_fwstate_(pmlmepriv, _FW_UNDER_SURVEY);
 	}
 
@@ -897,7 +899,6 @@
 {
 	struct	mlme_priv *pmlmepriv = &adapter->mlmepriv;
 	struct wlan_network *tgt_network = &pmlmepriv->cur_network;
-	struct	sta_priv *pstapriv = &adapter->stapriv;
 	struct dvobj_priv *psdpriv = adapter->dvobj;
 	struct debug_priv *pdbgpriv = &psdpriv->drv_dbg;
 
@@ -905,11 +906,7 @@
 		struct sta_info *psta;
 
 		psta = rtw_get_stainfo(&adapter->stapriv, tgt_network->network.mac_address);
-		spin_lock_bh(&(pstapriv->sta_hash_lock));
 		rtw_free_stainfo(adapter,  psta);
-
-		spin_unlock_bh(&(pstapriv->sta_hash_lock));
-
 	}
 
 	if (check_fwstate(pmlmepriv, WIFI_ADHOC_STATE|WIFI_ADHOC_MASTER_STATE|WIFI_AP_STATE)) {
@@ -1239,16 +1236,15 @@
 				rtw_indicate_connect(adapter);
 			}
 
+			spin_unlock_bh(&pmlmepriv->scanned_queue.lock);
+
+			spin_unlock_bh(&pmlmepriv->lock);
 			/* s5. Cancel assoc_timer */
 			del_timer_sync(&pmlmepriv->assoc_timer);
-
+			spin_lock_bh(&pmlmepriv->lock);
 		} else {
 			spin_unlock_bh(&(pmlmepriv->scanned_queue.lock));
-			goto ignore_joinbss_callback;
 		}
-
-		spin_unlock_bh(&(pmlmepriv->scanned_queue.lock));
-
 	} else if (pnetwork->join_res == -4) {
 		rtw_reset_securitypriv(adapter);
 		_set_timer(&pmlmepriv->assoc_timer, 1);
@@ -1820,7 +1816,7 @@
 			goto exit;
 	}
 
-	if (*candidate == NULL || (*candidate)->network.rssi < competitor->network.rssi) {
+	if (!*candidate || (*candidate)->network.rssi < competitor->network.rssi) {
 		*candidate = competitor;
 		updated = true;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_mlme_ext.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_mlme_ext.c
@@ -742,11 +742,11 @@
 	}
 
 	pstat = rtw_get_stainfo(pstapriv, sa);
-	if (pstat == NULL) {
+	if (!pstat) {
 
 		/*  allocate a new one */
 		pstat = rtw_alloc_stainfo(pstapriv, sa);
-		if (pstat == NULL) {
+		if (!pstat) {
 			status = WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA;
 			goto auth_fail;
 		}
@@ -814,7 +814,7 @@
 			p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + 4 + _AUTH_IE_OFFSET_, WLAN_EID_CHALLENGE, (int *)&ie_len,
 					len - WLAN_HDR_A3_LEN - _AUTH_IE_OFFSET_ - 4);
 
-			if ((p == NULL) || (ie_len <= 0)) {
+			if (!p || ie_len <= 0) {
 				status = WLAN_STATUS_CHALLENGE_FAIL;
 				goto auth_fail;
 			}
@@ -1034,7 +1034,7 @@
 
 	/*  check if the supported rate is ok */
 	p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + ie_offset, WLAN_EID_SUPP_RATES, &ie_len, pkt_len - WLAN_HDR_A3_LEN - ie_offset);
-	if (p == NULL) {
+	if (!p) {
 		/*  use our own rate set as statoin used */
 		/* memcpy(supportRate, AP_BSSRATE, AP_BSSRATE_LEN); */
 		/* supportRateNum = AP_BSSRATE_LEN; */
@@ -1047,7 +1047,7 @@
 
 		p = rtw_get_ie(pframe + WLAN_HDR_A3_LEN + ie_offset, WLAN_EID_EXT_SUPP_RATES, &ie_len,
 				pkt_len - WLAN_HDR_A3_LEN - ie_offset);
-		if (p !=  NULL) {
+		if (p) {
 
 			if (supportRateNum <= sizeof(supportRate)) {
 				memcpy(supportRate+supportRateNum, p+2, ie_len);
@@ -1294,7 +1294,7 @@
 	/* get a unique AID */
 	if (pstat->aid == 0) {
 		for (pstat->aid = 1; pstat->aid <= NUM_STA; pstat->aid++)
-			if (pstapriv->sta_aid[pstat->aid - 1] == NULL)
+			if (!pstapriv->sta_aid[pstat->aid - 1])
 				break;
 
 		/* if (pstat->aid > NUM_STA) { */
@@ -1489,9 +1489,7 @@
 		struct sta_info *psta;
 		struct sta_priv *pstapriv = &padapter->stapriv;
 
-		/* spin_lock_bh(&(pstapriv->sta_hash_lock)); */
 		/* rtw_free_stainfo(padapter, psta); */
-		/* spin_unlock_bh(&(pstapriv->sta_hash_lock)); */
 
 		netdev_dbg(padapter->pnetdev,
 			   "ap recv deauth reason code(%d) sta:%pM\n", reason,
@@ -1565,9 +1563,7 @@
 		struct sta_info *psta;
 		struct sta_priv *pstapriv = &padapter->stapriv;
 
-		/* spin_lock_bh(&(pstapriv->sta_hash_lock)); */
 		/* rtw_free_stainfo(padapter, psta); */
-		/* spin_unlock_bh(&(pstapriv->sta_hash_lock)); */
 
 		netdev_dbg(padapter->pnetdev,
 			   "ap recv disassoc reason code(%d) sta:%pM\n",
@@ -1944,7 +1940,7 @@
 		goto exit;
 
 	pxmitbuf = rtw_alloc_xmitbuf_ext(pxmitpriv);
-	if (pxmitbuf == NULL) {
+	if (!pxmitbuf) {
 		rtw_free_xmitframe(pxmitpriv, pmgntframe);
 		pmgntframe = NULL;
 		goto exit;
@@ -2297,7 +2293,7 @@
 	struct wlan_bssid_ex		*cur_network = &(pmlmeinfo->network);
 	unsigned int	rate_len;
 
-	if (da == NULL)
+	if (!da)
 		return;
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
@@ -2621,7 +2617,7 @@
 	__le16 le_tmp;
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL)
+	if (!pmgntframe)
 		return;
 
 	/* update attribute */
@@ -2752,7 +2748,7 @@
 	__le16 lestatus, le_tmp;
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL)
+	if (!pmgntframe)
 		return;
 
 	/* update attribute */
@@ -2840,7 +2836,7 @@
 				break;
 			}
 
-			if ((pbuf == NULL) || (ie_len == 0)) {
+			if (!pbuf || ie_len == 0) {
 				break;
 			}
 		}
@@ -2884,7 +2880,7 @@
 	u8 vs_ie_length = 0;
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL)
+	if (!pmgntframe)
 		goto exit;
 
 	/* update attribute */
@@ -3061,7 +3057,7 @@
 	pmlmeinfo = &(pmlmeext->mlmext_info);
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL)
+	if (!pmgntframe)
 		goto exit;
 
 	/* update attribute */
@@ -3200,7 +3196,7 @@
 	struct mlme_ext_info *pmlmeinfo = &(pmlmeext->mlmext_info);
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL)
+	if (!pmgntframe)
 		goto exit;
 
 	/* update attribute */
@@ -3313,7 +3309,7 @@
 	__le16 le_tmp;
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL) {
+	if (!pmgntframe) {
 		goto exit;
 	}
 
@@ -3639,7 +3635,7 @@
 	action = ACT_PUBLIC_BSSCOEXIST;
 
 	pmgntframe = alloc_mgtxmitframe(pxmitpriv);
-	if (pmgntframe == NULL) {
+	if (!pmgntframe) {
 		return;
 	}
 
@@ -3706,7 +3702,7 @@
 			pbss_network = (struct wlan_bssid_ex *)&pnetwork->network;
 
 			p = rtw_get_ie(pbss_network->ies + _FIXED_IE_LENGTH_, WLAN_EID_HT_CAPABILITY, &len, pbss_network->ie_length - _FIXED_IE_LENGTH_);
-			if ((p == NULL) || (len == 0)) {/* non-HT */
+			if (!p || len == 0) {/* non-HT */
 
 				if (pbss_network->configuration.ds_config <= 0)
 					continue;
@@ -3769,7 +3765,7 @@
 			return _SUCCESS;
 
 	psta = rtw_get_stainfo(pstapriv, addr);
-	if (psta == NULL)
+	if (!psta)
 		return _SUCCESS;
 
 	if (initiator == 0) {/*  recipient */
@@ -4641,13 +4637,13 @@
 	struct cmd_priv *pcmdpriv = &padapter->cmdpriv;
 
 	pcmd_obj = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (pcmd_obj == NULL) {
+	if (!pcmd_obj) {
 		return;
 	}
 
 	cmdsz = (sizeof(struct stadel_event) + sizeof(struct C2HEvent_Header));
 	pevtcmd = rtw_zmalloc(cmdsz);
-	if (pevtcmd == NULL) {
+	if (!pevtcmd) {
 		kfree(pcmd_obj);
 		return;
 	}
@@ -4693,12 +4689,12 @@
 	struct cmd_priv *pcmdpriv = &padapter->cmdpriv;
 
 	pcmd_obj = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (pcmd_obj == NULL)
+	if (!pcmd_obj)
 		return;
 
 	cmdsz = (sizeof(struct stassoc_event) + sizeof(struct C2HEvent_Header));
 	pevtcmd = rtw_zmalloc(cmdsz);
-	if (pevtcmd == NULL) {
+	if (!pevtcmd) {
 		kfree(pcmd_obj);
 		return;
 	}
@@ -5147,12 +5143,12 @@
 		}
 
 		ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-		if (ph2c == NULL) {
+		if (!ph2c) {
 			goto exit_survey_timer_hdl;
 		}
 
 		psurveyPara = rtw_zmalloc(sizeof(struct sitesurvey_parm));
-		if (psurveyPara == NULL) {
+		if (!psurveyPara) {
 			kfree(ph2c);
 			goto exit_survey_timer_hdl;
 		}
@@ -5781,7 +5777,7 @@
 	u8 res = _SUCCESS;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
@@ -5805,13 +5801,13 @@
 	int len_diff = 0;
 
 	ph2c = rtw_zmalloc(sizeof(struct cmd_obj));
-	if (ph2c == NULL) {
+	if (!ph2c) {
 		res = _FAIL;
 		goto exit;
 	}
 
 	ptxBeacon_parm = rtw_zmalloc(sizeof(struct Tx_Beacon_param));
-	if (ptxBeacon_parm == NULL) {
+	if (!ptxBeacon_parm) {
 		kfree(ph2c);
 		res = _FAIL;
 		goto exit;
@@ -5871,7 +5867,7 @@
 	void (*event_callback)(struct adapter *dev, u8 *pbuf);
 	struct evt_priv *pevt_priv = &(padapter->evtpriv);
 
-	if (pbuf == NULL)
+	if (!pbuf)
 		goto _abort_event_;
 
 	peventbuf = (uint *)pbuf;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_security.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_security.c
@@ -51,7 +51,7 @@
 	struct xmit_priv *pxmitpriv = &padapter->xmitpriv;
 	struct arc4_ctx *ctx = &psecuritypriv->xmit_arc4_ctx;
 
-	if (((struct xmit_frame *)pxmitframe)->buf_addr == NULL)
+	if (!((struct xmit_frame *)pxmitframe)->buf_addr)
 		return;
 
 	hw_hdr_offset = TXDESC_OFFSET;
@@ -476,7 +476,7 @@
 	struct arc4_ctx *ctx = &psecuritypriv->xmit_arc4_ctx;
 	u32 res = _SUCCESS;
 
-	if (((struct xmit_frame *)pxmitframe)->buf_addr == NULL)
+	if (!((struct xmit_frame *)pxmitframe)->buf_addr)
 		return _FAIL;
 
 	hw_hdr_offset = TXDESC_OFFSET;
@@ -1043,7 +1043,7 @@
 
 	u32 res = _SUCCESS;
 
-	if (((struct xmit_frame *)pxmitframe)->buf_addr == NULL)
+	if (!((struct xmit_frame *)pxmitframe)->buf_addr)
 		return _FAIL;
 
 	hw_hdr_offset = TXDESC_OFFSET;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/core/rtw_sta_mgt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/core/rtw_sta_mgt.c
@@ -263,7 +263,6 @@
 	return psta;
 }
 
-/*  using pstapriv->sta_hash_lock to protect */
 u32 rtw_free_stainfo(struct adapter *padapter, struct sta_info *psta)
 {
 	int i;
@@ -332,8 +331,10 @@
 
 	spin_unlock_bh(&pxmitpriv->lock);
 
+	spin_lock_bh(&pstapriv->sta_hash_lock);
 	list_del_init(&psta->hash_list);
 	pstapriv->asoc_sta_count--;
+	spin_unlock_bh(&pstapriv->sta_hash_lock);
 
 	/*  re-init sta_info; 20061114 will be init in alloc_stainfo */
 	/* _rtw_init_sta_xmit_priv(&psta->sta_xmitpriv); */
@@ -428,6 +429,7 @@
 	struct sta_info *psta = NULL;
 	struct	sta_priv *pstapriv = &padapter->stapriv;
 	struct sta_info *pbcmc_stainfo = rtw_get_bcmc_stainfo(padapter);
+	LIST_HEAD(stainfo_free_list);
 
 	if (pstapriv->asoc_sta_count == 1)
 		return;
@@ -440,11 +442,16 @@
 			psta = list_entry(plist, struct sta_info, hash_list);
 
 			if (pbcmc_stainfo != psta)
-				rtw_free_stainfo(padapter, psta);
+				list_move(&psta->hash_list, &stainfo_free_list);
 		}
 	}
 
 	spin_unlock_bh(&pstapriv->sta_hash_lock);
+
+	list_for_each_safe(plist, tmp, &stainfo_free_list) {
+		psta = list_entry(plist, struct sta_info, hash_list);
+		rtw_free_stainfo(padapter, psta);
+	}
 }
 
 /* any station allocated can be searched by hash list */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/include/rtw_security.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/include/rtw_security.h
@@ -107,13 +107,13 @@
 
 	u32 dot118021XGrpPrivacy;	/*  This specify the privacy algthm. used for Grp key */
 	u32 dot118021XGrpKeyid;		/*  key id used for Grp Key (tx key index) */
-	union Keytype	dot118021XGrpKey[BIP_MAX_KEYID];	/*  802.1x Group Key, for inx0 and inx1 */
-	union Keytype	dot118021XGrptxmickey[BIP_MAX_KEYID];
-	union Keytype	dot118021XGrprxmickey[BIP_MAX_KEYID];
+	union Keytype	dot118021XGrpKey[BIP_MAX_KEYID + 1];	/*  802.1x Group Key, for inx0 and inx1 */
+	union Keytype	dot118021XGrptxmickey[BIP_MAX_KEYID + 1];
+	union Keytype	dot118021XGrprxmickey[BIP_MAX_KEYID + 1];
 	union pn48		dot11Grptxpn;			/*  PN48 used for Grp Key xmit. */
 	union pn48		dot11Grprxpn;			/*  PN48 used for Grp Key recv. */
 	u32 dot11wBIPKeyid;						/*  key id used for BIP Key (tx key index) */
-	union Keytype	dot11wBIPKey[6];		/*  BIP Key, for index4 and index5 */
+	union Keytype	dot11wBIPKey[BIP_MAX_KEYID + 1];	/*  BIP Key, for index4 and index5 */
 	union pn48		dot11wBIPtxpn;			/*  PN48 used for Grp Key xmit. */
 	union pn48		dot11wBIPrxpn;			/*  PN48 used for Grp Key recv. */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/os_dep/ioctl_cfg80211.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/os_dep/ioctl_cfg80211.c
@@ -113,13 +113,10 @@
 	struct ieee80211_supported_band *spt_band = NULL;
 	int n_channels, n_bitrates;
 
-	if (band == NL80211_BAND_2GHZ)
-	{
+	if (band == NL80211_BAND_2GHZ) {
 		n_channels = RTW_2G_CHANNELS_NUM;
 		n_bitrates = RTW_G_RATES_NUM;
-	}
-	else
-	{
+	} else {
 		goto exit;
 	}
 
@@ -135,8 +132,7 @@
 	spt_band->n_channels = n_channels;
 	spt_band->n_bitrates = n_bitrates;
 
-	if (band == NL80211_BAND_2GHZ)
-	{
+	if (band == NL80211_BAND_2GHZ) {
 		rtw_2g_channels_init(spt_band->channels);
 		rtw_2g_rates_init(spt_band->bitrates);
 	}
@@ -235,8 +231,7 @@
 	{
 		u16 wapi_len = 0;
 
-		if (rtw_get_wapi_ie(pnetwork->network.ies, pnetwork->network.ie_length, NULL, &wapi_len) > 0)
-		{
+		if (rtw_get_wapi_ie(pnetwork->network.ies, pnetwork->network.ie_length, NULL, &wapi_len) > 0) {
 			if (wapi_len > 0)
 				goto exit;
 		}
@@ -244,8 +239,7 @@
 
 	/* To reduce PBC Overlap rate */
 	/* spin_lock_bh(&pwdev_priv->scan_req_lock); */
-	if (adapter_wdev_data(padapter)->scan_request)
-	{
+	if (adapter_wdev_data(padapter)->scan_request) {
 		u8 *psr = NULL, sr = 0;
 		struct ndis_802_11_ssid *pssid = &pnetwork->network.ssid;
 		struct cfg80211_scan_request *request = adapter_wdev_data(padapter)->scan_request;
@@ -258,14 +252,12 @@
 		if (wpsie && wpsielen > 0)
 			psr = rtw_get_wps_attr_content(wpsie,  wpsielen, WPS_ATTR_SELECTED_REGISTRAR, (u8 *)(&sr), NULL);
 
-		if (sr != 0)
-		{
-			if (request->n_ssids == 1 && request->n_channels == 1) /*  it means under processing WPS */
-			{
+		if (sr != 0) {
+			/* it means under processing WPS */
+			if (request->n_ssids == 1 && request->n_channels == 1) {
 				if (ssids[0].ssid_len != 0 &&
 				    (pssid->ssid_length != ssids[0].ssid_len ||
-				     memcmp(pssid->ssid, ssids[0].ssid, ssids[0].ssid_len)))
-				{
+				     memcmp(pssid->ssid, ssids[0].ssid, ssids[0].ssid_len))) {
 					if (psr)
 						*psr = 0; /* clear sr */
 				}
@@ -358,7 +350,7 @@
 	bss = cfg80211_get_bss(padapter->rtw_wdev->wiphy, notify_channel,
 			pnetwork->mac_address, pnetwork->ssid.ssid,
 			pnetwork->ssid.ssid_length,
-			WLAN_CAPABILITY_ESS, WLAN_CAPABILITY_ESS);
+			IEEE80211_BSS_TYPE_ANY, IEEE80211_PRIVACY_ANY);
 
 	cfg80211_put_bss(padapter->rtw_wdev->wiphy, bss);
 
@@ -375,23 +367,18 @@
 	struct ieee80211_channel *chan;
 
 	if (pwdev->iftype != NL80211_IFTYPE_ADHOC)
-	{
 		return;
-	}
 
 	if (!rtw_cfg80211_check_bss(padapter)) {
 		struct wlan_bssid_ex  *pnetwork = &(padapter->mlmeextpriv.mlmext_info.network);
 		struct wlan_network *scanned = pmlmepriv->cur_network_scanned;
 
-		if (check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE) == true)
-		{
+		if (check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE) == true) {
 
 			memcpy(&cur_network->network, pnetwork, sizeof(struct wlan_bssid_ex));
 			rtw_cfg80211_inform_bss(padapter, cur_network);
-		}
-		else
-		{
-			if (scanned == NULL) {
+		} else {
+			if (!scanned) {
 				rtw_warn_on(1);
 				return;
 			}
@@ -432,7 +419,7 @@
 		struct wlan_bssid_ex  *pnetwork = &(padapter->mlmeextpriv.mlmext_info.network);
 		struct wlan_network *scanned = pmlmepriv->cur_network_scanned;
 
-		if (scanned == NULL) {
+		if (!scanned) {
 			rtw_warn_on(1);
 			goto check_bss;
 		}
@@ -473,9 +460,7 @@
 		roam_info.resp_ie_len =
 			pmlmepriv->assoc_rsp_len-sizeof(struct ieee80211_hdr_3addr)-6;
 		cfg80211_roamed(padapter->pnetdev, &roam_info, GFP_ATOMIC);
-	}
-	else
-	{
+	} else {
 		cfg80211_connect_result(padapter->pnetdev, cur_network->network.mac_address
 			, pmlmepriv->assoc_req+sizeof(struct ieee80211_hdr_3addr)+2
 			, pmlmepriv->assoc_req_len-sizeof(struct ieee80211_hdr_3addr)-2
@@ -527,51 +512,41 @@
 	param->u.crypt.err = 0;
 	param->u.crypt.alg[IEEE_CRYPT_ALG_NAME_LEN - 1] = '\0';
 
-	if (param_len !=  sizeof(struct ieee_param) + param->u.crypt.key_len)
-	{
+	if (param_len !=  sizeof(struct ieee_param) + param->u.crypt.key_len) {
 		ret =  -EINVAL;
 		goto exit;
 	}
 
 	if (param->sta_addr[0] == 0xff && param->sta_addr[1] == 0xff &&
 	    param->sta_addr[2] == 0xff && param->sta_addr[3] == 0xff &&
-	    param->sta_addr[4] == 0xff && param->sta_addr[5] == 0xff)
-	{
-		if (param->u.crypt.idx >= WEP_KEYS)
-		{
+	    param->sta_addr[4] == 0xff && param->sta_addr[5] == 0xff) {
+		if (param->u.crypt.idx >= WEP_KEYS) {
 			ret = -EINVAL;
 			goto exit;
 		}
-	}
-	else
-	{
+	} else {
 		psta = rtw_get_stainfo(pstapriv, param->sta_addr);
 		if (!psta)
 			/* ret = -EINVAL; */
 			goto exit;
 	}
 
-	if (strcmp(param->u.crypt.alg, "none") == 0 && (psta == NULL))
+	if (strcmp(param->u.crypt.alg, "none") == 0 && !psta)
 		goto exit;
 
-	if (strcmp(param->u.crypt.alg, "WEP") == 0 && (psta == NULL))
-	{
+	if (strcmp(param->u.crypt.alg, "WEP") == 0 && !psta) {
 		wep_key_idx = param->u.crypt.idx;
 		wep_key_len = param->u.crypt.key_len;
 
-		if ((wep_key_idx >= WEP_KEYS) || (wep_key_len <= 0))
-		{
+		if ((wep_key_idx >= WEP_KEYS) || (wep_key_len <= 0)) {
 			ret = -EINVAL;
 			goto exit;
 		}
 
 		if (wep_key_len > 0)
-		{
 			wep_key_len = wep_key_len <= 5 ? 5 : 13;
-		}
 
-		if (psecuritypriv->bWepDefaultKeyIdxSet == 0)
-		{
+		if (psecuritypriv->bWepDefaultKeyIdxSet == 0) {
 			/* wep default key has not been set, so use this key index as default key. */
 
 			psecuritypriv->dot11AuthAlgrthm = dot11AuthAlgrthm_Auto;
@@ -579,8 +554,7 @@
 			psecuritypriv->dot11PrivacyAlgrthm = _WEP40_;
 			psecuritypriv->dot118021XGrpPrivacy = _WEP40_;
 
-			if (wep_key_len == 13)
-			{
+			if (wep_key_len == 13) {
 				psecuritypriv->dot11PrivacyAlgrthm = _WEP104_;
 				psecuritypriv->dot118021XGrpPrivacy = _WEP104_;
 			}
@@ -598,24 +572,18 @@
 
 	}
 
-
-	if (!psta && check_fwstate(pmlmepriv, WIFI_AP_STATE)) /* group key */
-	{
-		if (param->u.crypt.set_tx == 0) /* group key */
-		{
-			if (strcmp(param->u.crypt.alg, "WEP") == 0)
-			{
+	/* group key */
+	if (!psta && check_fwstate(pmlmepriv, WIFI_AP_STATE)) {
+		/* group key */
+		if (param->u.crypt.set_tx == 0) {
+			if (strcmp(param->u.crypt.alg, "WEP") == 0) {
 				memcpy(grpkey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
 
 				psecuritypriv->dot118021XGrpPrivacy = _WEP40_;
 				if (param->u.crypt.key_len == 13)
-				{
 						psecuritypriv->dot118021XGrpPrivacy = _WEP104_;
-				}
 
-			}
-			else if (strcmp(param->u.crypt.alg, "TKIP") == 0)
-			{
+			} else if (strcmp(param->u.crypt.alg, "TKIP") == 0) {
 				psecuritypriv->dot118021XGrpPrivacy = _TKIP_;
 
 				memcpy(grpkey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
@@ -627,15 +595,11 @@
 
 				psecuritypriv->busetkipkey = true;
 
-			}
-			else if (strcmp(param->u.crypt.alg, "CCMP") == 0)
-			{
+			} else if (strcmp(param->u.crypt.alg, "CCMP") == 0) {
 				psecuritypriv->dot118021XGrpPrivacy = _AES_;
 
 				memcpy(grpkey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
-			}
-			else
-			{
+			} else {
 				psecuritypriv->dot118021XGrpPrivacy = _NO_PRIVACY_;
 			}
 
@@ -648,8 +612,7 @@
 			rtw_ap_set_group_key(padapter, param->u.crypt.key, psecuritypriv->dot118021XGrpPrivacy, param->u.crypt.idx);
 
 			pbcmc_sta = rtw_get_bcmc_stainfo(padapter);
-			if (pbcmc_sta)
-			{
+			if (pbcmc_sta) {
 				pbcmc_sta->ieee8021x_blocked = false;
 				pbcmc_sta->dot118021XPrivacy = psecuritypriv->dot118021XGrpPrivacy;/* rx will use bmc_sta's dot118021XPrivacy */
 			}
@@ -660,24 +623,16 @@
 
 	}
 
-	if (psecuritypriv->dot11AuthAlgrthm == dot11AuthAlgrthm_8021X && psta) /*  psk/802_1x */
-	{
-		if (check_fwstate(pmlmepriv, WIFI_AP_STATE))
-		{
-			if (param->u.crypt.set_tx == 1) /* pairwise key */
-			{
+	if (psecuritypriv->dot11AuthAlgrthm == dot11AuthAlgrthm_8021X && psta) { /*  psk/802_1x */
+		if (check_fwstate(pmlmepriv, WIFI_AP_STATE)) {
+			if (param->u.crypt.set_tx == 1) { /* pairwise key */
 				memcpy(psta->dot118021x_UncstKey.skey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
 
-				if (strcmp(param->u.crypt.alg, "WEP") == 0)
-				{
+				if (strcmp(param->u.crypt.alg, "WEP") == 0) {
 					psta->dot118021XPrivacy = _WEP40_;
 					if (param->u.crypt.key_len == 13)
-					{
 						psta->dot118021XPrivacy = _WEP104_;
-					}
-				}
-				else if (strcmp(param->u.crypt.alg, "TKIP") == 0)
-				{
+				} else if (strcmp(param->u.crypt.alg, "TKIP") == 0) {
 					psta->dot118021XPrivacy = _TKIP_;
 
 					/* DEBUG_ERR("set key length :param->u.crypt.key_len =%d\n", param->u.crypt.key_len); */
@@ -687,14 +642,10 @@
 
 					psecuritypriv->busetkipkey = true;
 
-				}
-				else if (strcmp(param->u.crypt.alg, "CCMP") == 0)
-				{
+				} else if (strcmp(param->u.crypt.alg, "CCMP") == 0) {
 
 					psta->dot118021XPrivacy = _AES_;
-				}
-				else
-				{
+				} else {
 					psta->dot118021XPrivacy = _NO_PRIVACY_;
 				}
 
@@ -704,21 +655,14 @@
 
 				psta->bpairwise_key_installed = true;
 
-			}
-			else/* group key??? */
-			{
-				if (strcmp(param->u.crypt.alg, "WEP") == 0)
-				{
+			} else { /* group key??? */
+				if (strcmp(param->u.crypt.alg, "WEP") == 0) {
 					memcpy(grpkey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
 
 					psecuritypriv->dot118021XGrpPrivacy = _WEP40_;
 					if (param->u.crypt.key_len == 13)
-					{
 						psecuritypriv->dot118021XGrpPrivacy = _WEP104_;
-					}
-				}
-				else if (strcmp(param->u.crypt.alg, "TKIP") == 0)
-				{
+				} else if (strcmp(param->u.crypt.alg, "TKIP") == 0) {
 					psecuritypriv->dot118021XGrpPrivacy = _TKIP_;
 
 					memcpy(grpkey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
@@ -730,15 +674,11 @@
 
 					psecuritypriv->busetkipkey = true;
 
-				}
-				else if (strcmp(param->u.crypt.alg, "CCMP") == 0)
-				{
+				} else if (strcmp(param->u.crypt.alg, "CCMP") == 0) {
 					psecuritypriv->dot118021XGrpPrivacy = _AES_;
 
 					memcpy(grpkey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
-				}
-				else
-				{
+				} else {
 					psecuritypriv->dot118021XGrpPrivacy = _NO_PRIVACY_;
 				}
 
@@ -751,8 +691,7 @@
 				rtw_ap_set_group_key(padapter, param->u.crypt.key, psecuritypriv->dot118021XGrpPrivacy, param->u.crypt.idx);
 
 				pbcmc_sta = rtw_get_bcmc_stainfo(padapter);
-				if (pbcmc_sta)
-				{
+				if (pbcmc_sta) {
 					pbcmc_sta->ieee8021x_blocked = false;
 					pbcmc_sta->dot118021XPrivacy = psecuritypriv->dot118021XGrpPrivacy;/* rx will use bmc_sta's dot118021XPrivacy */
 				}
@@ -772,6 +711,7 @@
 static int rtw_cfg80211_set_encryption(struct net_device *dev, struct ieee_param *param, u32 param_len)
 {
 	int ret = 0;
+	u8 max_idx;
 	u32 wep_key_idx, wep_key_len;
 	struct adapter *padapter = rtw_netdev_priv(dev);
 	struct mlme_priv *pmlmepriv = &padapter->mlmepriv;
@@ -780,43 +720,39 @@
 	param->u.crypt.err = 0;
 	param->u.crypt.alg[IEEE_CRYPT_ALG_NAME_LEN - 1] = '\0';
 
-	if (param_len < (u32) ((u8 *) param->u.crypt.key - (u8 *) param) + param->u.crypt.key_len)
-	{
+	if (param_len < (u32) ((u8 *) param->u.crypt.key - (u8 *) param) + param->u.crypt.key_len) {
 		ret =  -EINVAL;
 		goto exit;
 	}
 
-	if (param->sta_addr[0] == 0xff && param->sta_addr[1] == 0xff &&
-	    param->sta_addr[2] == 0xff && param->sta_addr[3] == 0xff &&
-	    param->sta_addr[4] == 0xff && param->sta_addr[5] == 0xff)
-	{
-		if (param->u.crypt.idx >= WEP_KEYS
-			|| param->u.crypt.idx >= BIP_MAX_KEYID
-		)
-		{
-			ret = -EINVAL;
-			goto exit;
-		}
-	} else {
-		{
+	if (param->sta_addr[0] != 0xff || param->sta_addr[1] != 0xff ||
+	    param->sta_addr[2] != 0xff || param->sta_addr[3] != 0xff ||
+	    param->sta_addr[4] != 0xff || param->sta_addr[5] != 0xff) {
 		ret = -EINVAL;
 		goto exit;
 	}
-	}
 
 	if (strcmp(param->u.crypt.alg, "WEP") == 0)
-	{
+		max_idx = WEP_KEYS - 1;
+	else
+		max_idx = BIP_MAX_KEYID;
+
+	if (param->u.crypt.idx > max_idx) {
+		netdev_err(dev, "Error crypt.idx %d > %d\n", param->u.crypt.idx, max_idx);
+		ret = -EINVAL;
+		goto exit;
+	}
+
+	if (strcmp(param->u.crypt.alg, "WEP") == 0) {
 		wep_key_idx = param->u.crypt.idx;
 		wep_key_len = param->u.crypt.key_len;
 
-		if ((wep_key_idx >= WEP_KEYS) || (wep_key_len <= 0))
-		{
+		if (wep_key_len <= 0) {
 			ret = -EINVAL;
 			goto exit;
 		}
 
-		if (psecuritypriv->bWepDefaultKeyIdxSet == 0)
-		{
+		if (psecuritypriv->bWepDefaultKeyIdxSet == 0) {
 			/* wep default key has not been set, so use this key index as default key. */
 
 			wep_key_len = wep_key_len <= 5 ? 5 : 13;
@@ -825,8 +761,7 @@
 			psecuritypriv->dot11PrivacyAlgrthm = _WEP40_;
 			psecuritypriv->dot118021XGrpPrivacy = _WEP40_;
 
-			if (wep_key_len == 13)
-			{
+			if (wep_key_len == 13) {
 				psecuritypriv->dot11PrivacyAlgrthm = _WEP104_;
 				psecuritypriv->dot118021XGrpPrivacy = _WEP104_;
 			}
@@ -843,13 +778,11 @@
 		goto exit;
 	}
 
-	if (padapter->securitypriv.dot11AuthAlgrthm == dot11AuthAlgrthm_8021X) /*  802_1x */
-	{
+	if (padapter->securitypriv.dot11AuthAlgrthm == dot11AuthAlgrthm_8021X) { /*  802_1x */
 		struct sta_info *psta, *pbcmc_sta;
 		struct sta_priv *pstapriv = &padapter->stapriv;
 
-		if (check_fwstate(pmlmepriv, WIFI_STATION_STATE | WIFI_MP_STATE) == true) /* sta mode */
-		{
+		if (check_fwstate(pmlmepriv, WIFI_STATION_STATE | WIFI_MP_STATE) == true) { /* sta mode */
 			psta = rtw_get_stainfo(pstapriv, get_bssid(pmlmepriv));
 			if (psta) {
 				/* Jeff: don't disable ieee8021x_blocked while clearing key */
@@ -858,18 +791,15 @@
 
 
 				if ((padapter->securitypriv.ndisencryptstatus == Ndis802_11Encryption2Enabled) ||
-						(padapter->securitypriv.ndisencryptstatus ==  Ndis802_11Encryption3Enabled))
-				{
+						(padapter->securitypriv.ndisencryptstatus ==  Ndis802_11Encryption3Enabled)) {
 					psta->dot118021XPrivacy = padapter->securitypriv.dot11PrivacyAlgrthm;
 				}
 
-				if (param->u.crypt.set_tx == 1)/* pairwise key */
-				{
+				if (param->u.crypt.set_tx == 1) { /* pairwise key */
 
 					memcpy(psta->dot118021x_UncstKey.skey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
 
-					if (strcmp(param->u.crypt.alg, "TKIP") == 0)/* set mic key */
-					{
+					if (strcmp(param->u.crypt.alg, "TKIP") == 0) { /* set mic key */
 						/* DEBUG_ERR(("\nset key length :param->u.crypt.key_len =%d\n", param->u.crypt.key_len)); */
 						memcpy(psta->dot11tkiptxmickey.skey, &(param->u.crypt.key[16]), 8);
 						memcpy(psta->dot11tkiprxmickey.skey, &(param->u.crypt.key[24]), 8);
@@ -879,11 +809,8 @@
 					}
 
 					rtw_setstakey_cmd(padapter, psta, true, true);
-				}
-				else/* group key */
-				{
-					if (strcmp(param->u.crypt.alg, "TKIP") == 0 || strcmp(param->u.crypt.alg, "CCMP") == 0)
-					{
+				} else { /* group key */
+					if (strcmp(param->u.crypt.alg, "TKIP") == 0 || strcmp(param->u.crypt.alg, "CCMP") == 0) {
 						memcpy(padapter->securitypriv.dot118021XGrpKey[param->u.crypt.idx].skey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
 						memcpy(padapter->securitypriv.dot118021XGrptxmickey[param->u.crypt.idx].skey, &(param->u.crypt.key[16]), 8);
 						memcpy(padapter->securitypriv.dot118021XGrprxmickey[param->u.crypt.idx].skey, &(param->u.crypt.key[24]), 8);
@@ -891,9 +818,7 @@
 
 						padapter->securitypriv.dot118021XGrpKeyid = param->u.crypt.idx;
 						rtw_set_key(padapter, &padapter->securitypriv, param->u.crypt.idx, 1, true);
-					}
-					else if (strcmp(param->u.crypt.alg, "BIP") == 0)
-					{
+					} else if (strcmp(param->u.crypt.alg, "BIP") == 0) {
 						/* save the IGTK key, length 16 bytes */
 						memcpy(padapter->securitypriv.dot11wBIPKey[param->u.crypt.idx].skey, param->u.crypt.key, (param->u.crypt.key_len > 16 ? 16 : param->u.crypt.key_len));
 						/*
@@ -907,25 +832,19 @@
 			}
 
 			pbcmc_sta = rtw_get_bcmc_stainfo(padapter);
-			if (pbcmc_sta == NULL)
-			{
+			if (!pbcmc_sta) {
 				/* DEBUG_ERR(("Set OID_802_11_ADD_KEY: bcmc stainfo is null\n")); */
-			}
-			else
-			{
+			} else {
 				/* Jeff: don't disable ieee8021x_blocked while clearing key */
 				if (strcmp(param->u.crypt.alg, "none") != 0)
 					pbcmc_sta->ieee8021x_blocked = false;
 
 				if ((padapter->securitypriv.ndisencryptstatus == Ndis802_11Encryption2Enabled) ||
-						(padapter->securitypriv.ndisencryptstatus ==  Ndis802_11Encryption3Enabled))
-				{
+						(padapter->securitypriv.ndisencryptstatus ==  Ndis802_11Encryption3Enabled)) {
 					pbcmc_sta->dot118021XPrivacy = padapter->securitypriv.dot11PrivacyAlgrthm;
 				}
 			}
-		}
-		else if (check_fwstate(pmlmepriv, WIFI_ADHOC_STATE)) /* adhoc mode */
-		{
+		} else if (check_fwstate(pmlmepriv, WIFI_ADHOC_STATE)) { /* adhoc mode */
 		}
 	}
 
@@ -947,7 +866,7 @@
 
 	param_len = sizeof(struct ieee_param) + params->key_len;
 	param = rtw_malloc(param_len);
-	if (param == NULL)
+	if (!param)
 		return -1;
 
 	memset(param, 0, param_len);
@@ -983,39 +902,29 @@
 
 
 	if (!mac_addr || is_broadcast_ether_addr(mac_addr))
-	{
 		param->u.crypt.set_tx = 0; /* for wpa/wpa2 group key */
-	} else {
+	else
 		param->u.crypt.set_tx = 1; /* for wpa/wpa2 pairwise key */
-	}
 
 	param->u.crypt.idx = key_index;
 
 	if (params->seq_len && params->seq)
-	{
 		memcpy(param->u.crypt.seq, (u8 *)params->seq, params->seq_len);
-	}
 
-	if (params->key_len && params->key)
-	{
+	if (params->key_len && params->key) {
 		param->u.crypt.key_len = params->key_len;
 		memcpy(param->u.crypt.key, (u8 *)params->key, params->key_len);
 	}
 
-	if (check_fwstate(pmlmepriv, WIFI_STATION_STATE) == true)
-	{
+	if (check_fwstate(pmlmepriv, WIFI_STATION_STATE) == true) {
 		ret =  rtw_cfg80211_set_encryption(ndev, param, param_len);
-	}
-	else if (check_fwstate(pmlmepriv, WIFI_AP_STATE) == true)
-	{
+	} else if (check_fwstate(pmlmepriv, WIFI_AP_STATE) == true) {
 		if (mac_addr)
 			memcpy(param->sta_addr, (void *)mac_addr, ETH_ALEN);
 
 		ret = rtw_cfg80211_ap_set_encryption(ndev, param, param_len);
-	}
-        else if (check_fwstate(pmlmepriv, WIFI_ADHOC_STATE) == true
-                || check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE) == true)
-        {
+	} else if (check_fwstate(pmlmepriv, WIFI_ADHOC_STATE) == true
+                || check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE) == true) {
                 ret =  rtw_cfg80211_set_encryption(ndev, param, param_len);
         }
 
@@ -1041,8 +950,7 @@
 	struct adapter *padapter = rtw_netdev_priv(ndev);
 	struct security_priv *psecuritypriv = &padapter->securitypriv;
 
-	if (key_index == psecuritypriv->dot11PrivacyKeyIndex)
-	{
+	if (key_index == psecuritypriv->dot11PrivacyKeyIndex) {
 		/* clear the flag of wep default key set. */
 		psecuritypriv->bWepDefaultKeyIdxSet = 0;
 	}
@@ -1058,16 +966,14 @@
 	struct adapter *padapter = rtw_netdev_priv(ndev);
 	struct security_priv *psecuritypriv = &padapter->securitypriv;
 
-	if ((key_index < WEP_KEYS) && ((psecuritypriv->dot11PrivacyAlgrthm == _WEP40_) || (psecuritypriv->dot11PrivacyAlgrthm == _WEP104_))) /* set wep default key */
-	{
+	if ((key_index < WEP_KEYS) && ((psecuritypriv->dot11PrivacyAlgrthm == _WEP40_) || (psecuritypriv->dot11PrivacyAlgrthm == _WEP104_))) { /* set wep default key */
 		psecuritypriv->ndisencryptstatus = Ndis802_11Encryption1Enabled;
 
 		psecuritypriv->dot11PrivacyKeyIndex = key_index;
 
 		psecuritypriv->dot11PrivacyAlgrthm = _WEP40_;
 		psecuritypriv->dot118021XGrpPrivacy = _WEP40_;
-		if (psecuritypriv->dot11DefKeylen[key_index] == 13)
-		{
+		if (psecuritypriv->dot11DefKeylen[key_index] == 13) {
 			psecuritypriv->dot11PrivacyAlgrthm = _WEP104_;
 			psecuritypriv->dot118021XGrpPrivacy = _WEP104_;
 		}
@@ -1098,16 +1004,14 @@
 	}
 
 	psta = rtw_get_stainfo(pstapriv, (u8 *)mac);
-	if (psta == NULL) {
+	if (!psta) {
 		ret = -ENOENT;
 		goto exit;
 	}
 
 	/* for infra./P2PClient mode */
 	if (check_fwstate(pmlmepriv, WIFI_STATION_STATE)
-		&& check_fwstate(pmlmepriv, _FW_LINKED)
-	)
-	{
+		&& check_fwstate(pmlmepriv, _FW_LINKED)) {
 		struct wlan_network  *cur_network = &(pmlmepriv->cur_network);
 
 		if (memcmp((u8 *)mac, cur_network->network.mac_address, ETH_ALEN)) {
@@ -1133,9 +1037,7 @@
 	if ((check_fwstate(pmlmepriv, WIFI_ADHOC_STATE)
  || check_fwstate(pmlmepriv, WIFI_ADHOC_MASTER_STATE)
  || check_fwstate(pmlmepriv, WIFI_AP_STATE))
-		&& check_fwstate(pmlmepriv, _FW_LINKED)
-	)
-	{
+		&& check_fwstate(pmlmepriv, _FW_LINKED)) {
 		/* TODO: should acquire station info... */
 	}
 
@@ -1155,8 +1057,7 @@
 	struct mlme_ext_priv *pmlmeext = &(padapter->mlmeextpriv);
 	int ret = 0;
 
-	if (adapter_to_dvobj(padapter)->processing_dev_remove == true)
-	{
+	if (adapter_to_dvobj(padapter)->processing_dev_remove == true) {
 		ret = -EPERM;
 		goto exit;
 	}
@@ -1175,8 +1076,7 @@
 
 	old_type = rtw_wdev->iftype;
 
-	if (old_type != type)
-	{
+	if (old_type != type) {
 		pmlmeext->action_public_rxseq = 0xffff;
 		pmlmeext->action_public_dialog_token = 0xff;
 	}
@@ -1198,8 +1098,7 @@
 
 	rtw_wdev->iftype = type;
 
-	if (rtw_set_802_11_infrastructure_mode(padapter, networkType) == false)
-	{
+	if (rtw_set_802_11_infrastructure_mode(padapter, networkType) == false) {
 		rtw_wdev->iftype = old_type;
 		ret = -EPERM;
 		goto exit;
@@ -1239,8 +1138,8 @@
 
 	bss = cfg80211_get_bss(wiphy, NULL/*notify_channel*/,
 		select_network->mac_address, select_network->ssid.ssid,
-		select_network->ssid.ssid_length, 0/*WLAN_CAPABILITY_ESS*/,
-		0/*WLAN_CAPABILITY_ESS*/);
+		select_network->ssid.ssid_length, IEEE80211_BSS_TYPE_ANY,
+		IEEE80211_PRIVACY_ANY);
 
 	if (bss) {
 		cfg80211_unlink_bss(wiphy, bss);
@@ -1264,9 +1163,7 @@
 
 		/* report network only if the current channel set contains the channel to which this network belongs */
 		if (rtw_ch_set_search_ch(padapter->mlmeextpriv.channel_set, pnetwork->network.configuration.ds_config) >= 0
-			&& true == rtw_validate_ssid(&(pnetwork->network.ssid))
-		)
-		{
+			&& true == rtw_validate_ssid(&(pnetwork->network.ssid))) {
 			/* ev =translate_scan(padapter, a, pnetwork, ev, stop); */
 			rtw_cfg80211_inform_bss(padapter, pnetwork);
 		}
@@ -1283,13 +1180,10 @@
 	u8 *wps_ie;
 	struct mlme_priv *pmlmepriv = &(padapter->mlmepriv);
 
-	if (len > 0)
-	{
+	if (len > 0) {
 		wps_ie = rtw_get_wps_ie(buf, len, NULL, &wps_ielen);
-		if (wps_ie)
-		{
-			if (pmlmepriv->wps_probe_req_ie)
-			{
+		if (wps_ie) {
+			if (pmlmepriv->wps_probe_req_ie) {
 				pmlmepriv->wps_probe_req_ie_len = 0;
 				kfree(pmlmepriv->wps_probe_req_ie);
 				pmlmepriv->wps_probe_req_ie = NULL;
@@ -1327,7 +1221,7 @@
 	struct rtw_wdev_priv *pwdev_priv;
 	struct mlme_priv *pmlmepriv;
 
-	if (ndev == NULL) {
+	if (!ndev) {
 		ret = -EINVAL;
 		goto exit;
 	}
@@ -1341,10 +1235,8 @@
 	pwdev_priv->scan_request = request;
 	spin_unlock_bh(&pwdev_priv->scan_req_lock);
 
-	if (check_fwstate(pmlmepriv, WIFI_AP_STATE) == true)
-	{
-		if (check_fwstate(pmlmepriv, WIFI_UNDER_WPS|_FW_UNDER_SURVEY|_FW_UNDER_LINKING) == true)
-		{
+	if (check_fwstate(pmlmepriv, WIFI_AP_STATE) == true) {
+		if (check_fwstate(pmlmepriv, WIFI_UNDER_WPS|_FW_UNDER_SURVEY|_FW_UNDER_LINKING) == true) {
 			need_indicate_scan_done = true;
 			goto check_need_indicate_scan_done;
 		}
@@ -1367,15 +1259,13 @@
 		goto check_need_indicate_scan_done;
 	}
 
-	if (pmlmepriv->LinkDetectInfo.bBusyTraffic == true)
-	{
+	if (pmlmepriv->LinkDetectInfo.bBusyTraffic == true) {
 		static unsigned long lastscantime = 0;
 		unsigned long passtime;
 
 		passtime = jiffies_to_msecs(jiffies - lastscantime);
 		lastscantime = jiffies;
-		if (passtime > 12000)
-		{
+		if (passtime > 12000) {
 			need_indicate_scan_done = true;
 			goto check_need_indicate_scan_done;
 		}
@@ -1414,9 +1304,7 @@
 	} else if (request->n_channels <= 4) {
 		for (j = request->n_channels - 1; j >= 0; j--)
 			for (i = 0; i < survey_times; i++)
-		{
 			memcpy(&ch[j*survey_times+i], &ch[j], sizeof(struct rtw_ieee80211_channel));
-		}
 		_status = rtw_sitesurvey_cmd(padapter, ssid, RTW_SSID_SCAN_AMOUNT, ch, survey_times * request->n_channels);
 	} else {
 		_status = rtw_sitesurvey_cmd(padapter, ssid, RTW_SSID_SCAN_AMOUNT, NULL, 0);
@@ -1425,14 +1313,11 @@
 
 
 	if (_status == false)
-	{
 		ret = -1;
-	}
 
 check_need_indicate_scan_done:
 	kfree(ssid);
-	if (need_indicate_scan_done)
-	{
+	if (need_indicate_scan_done) {
 		rtw_cfg80211_surveydone_event_callback(padapter);
 		rtw_cfg80211_indicate_scan_done(padapter, false);
 	}
@@ -1458,9 +1343,7 @@
 
 
 	if (wpa_version & (NL80211_WPA_VERSION_1 | NL80211_WPA_VERSION_2))
-	{
 		psecuritypriv->ndisauthtype = Ndis802_11AuthModeWPAPSK;
-	}
 
 	return 0;
 
@@ -1571,7 +1454,7 @@
 	u8 *pwpa, *pwpa2;
 	u8 null_addr[] = {0, 0, 0, 0, 0, 0};
 
-	if (pie == NULL || !ielen) {
+	if (!pie || !ielen) {
 		/* Treat this as normal case, but need to clear WIFI_UNDER_WPS */
 		_clr_fwstate_(&padapter->mlmepriv, WIFI_UNDER_WPS);
 		goto exit;
@@ -1583,7 +1466,7 @@
 	}
 
 	buf = rtw_zmalloc(ielen);
-	if (buf == NULL) {
+	if (!buf) {
 		ret =  -ENOMEM;
 		goto exit;
 	}
@@ -1619,8 +1502,7 @@
 	if (pairwise_cipher == 0)
 		pairwise_cipher = WPA_CIPHER_NONE;
 
-	switch (group_cipher)
-	{
+	switch (group_cipher) {
 		case WPA_CIPHER_NONE:
 			padapter->securitypriv.dot118021XGrpPrivacy = _NO_PRIVACY_;
 			padapter->securitypriv.ndisencryptstatus = Ndis802_11EncryptionDisabled;
@@ -1643,8 +1525,7 @@
 			break;
 	}
 
-	switch (pairwise_cipher)
-	{
+	switch (pairwise_cipher) {
 		case WPA_CIPHER_NONE:
 			padapter->securitypriv.dot11PrivacyAlgrthm = _NO_PRIVACY_;
 			padapter->securitypriv.ndisencryptstatus = Ndis802_11EncryptionDisabled;
@@ -1765,8 +1646,7 @@
 
 		rtw_wdev->iftype = NL80211_IFTYPE_STATION;
 
-		if (rtw_set_802_11_infrastructure_mode(padapter, Ndis802_11Infrastructure) == false)
-		{
+		if (rtw_set_802_11_infrastructure_mode(padapter, Ndis802_11Infrastructure) == false) {
 			rtw_wdev->iftype = old_type;
 			ret = -EPERM;
 			goto leave_ibss;
@@ -1826,9 +1706,8 @@
 		ret = -EBUSY;
 		goto exit;
 	}
-	if (check_fwstate(pmlmepriv, _FW_UNDER_SURVEY) == true) {
+	if (check_fwstate(pmlmepriv, _FW_UNDER_SURVEY) == true)
 		rtw_scan_abort(padapter);
-	}
 
 	psecuritypriv->ndisencryptstatus = Ndis802_11EncryptionDisabled;
 	psecuritypriv->dot11PrivacyAlgrthm = _NO_PRIVACY_;
@@ -1873,7 +1752,7 @@
 			wep_key_len = wep_key_len <= 5 ? 5 : 13;
 			wep_total_len = wep_key_len + FIELD_OFFSET(struct ndis_802_11_wep, key_material);
 			pwep = rtw_malloc(wep_total_len);
-			if (pwep == NULL) {
+			if (!pwep) {
 				ret = -ENOMEM;
 				goto exit;
 			}
@@ -2321,9 +2200,8 @@
 	mon_ndev->ieee80211_ptr = mon_wdev;
 
 	ret = cfg80211_register_netdevice(mon_ndev);
-	if (ret) {
+	if (ret)
 		goto out;
-	}
 
 	*ndev = pwdev_priv->pmon_ndev = mon_ndev;
 	memcpy(pwdev_priv->ifname_mon, name, IFNAMSIZ+1);
@@ -2436,11 +2314,10 @@
 	rtw_ies_remove_ie(pbuf, &len, _BEACON_IE_OFFSET_, WLAN_EID_VENDOR_SPECIFIC, P2P_OUI, 4);
 	rtw_ies_remove_ie(pbuf, &len, _BEACON_IE_OFFSET_, WLAN_EID_VENDOR_SPECIFIC, WFD_OUI, 4);
 
-	if (rtw_check_beacon_data(adapter, pbuf,  len) == _SUCCESS) {
+	if (rtw_check_beacon_data(adapter, pbuf,  len) == _SUCCESS)
 		ret = 0;
-	} else {
+	else
 		ret = -EINVAL;
-	}
 
 
 	kfree(pbuf);
@@ -2708,7 +2585,7 @@
 	struct adapter *padapter;
 	struct rtw_wdev_priv *pwdev_priv;
 
-	if (ndev == NULL) {
+	if (!ndev) {
 		ret = -EINVAL;
 		goto exit;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/os_dep/ioctl_linux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/os_dep/ioctl_linux.c
@@ -60,6 +60,7 @@
 static int wpa_set_encryption(struct net_device *dev, struct ieee_param *param, u32 param_len)
 {
 	int ret = 0;
+	u8 max_idx;
 	u32 wep_key_idx, wep_key_len, wep_total_len;
 	struct ndis_802_11_wep	 *pwep = NULL;
 	struct adapter *padapter = rtw_netdev_priv(dev);
@@ -74,19 +75,22 @@
 		goto exit;
 	}
 
-	if (param->sta_addr[0] == 0xff && param->sta_addr[1] == 0xff &&
-	    param->sta_addr[2] == 0xff && param->sta_addr[3] == 0xff &&
-	    param->sta_addr[4] == 0xff && param->sta_addr[5] == 0xff) {
-		if (param->u.crypt.idx >= WEP_KEYS ||
-		    param->u.crypt.idx >= BIP_MAX_KEYID) {
-			ret = -EINVAL;
-			goto exit;
-		}
-	} else {
-		{
-			ret = -EINVAL;
-			goto exit;
-		}
+	if (param->sta_addr[0] != 0xff || param->sta_addr[1] != 0xff ||
+	    param->sta_addr[2] != 0xff || param->sta_addr[3] != 0xff ||
+	    param->sta_addr[4] != 0xff || param->sta_addr[5] != 0xff) {
+		ret = -EINVAL;
+		goto exit;
+	}
+
+	if (strcmp(param->u.crypt.alg, "WEP") == 0)
+		max_idx = WEP_KEYS - 1;
+	else
+		max_idx = BIP_MAX_KEYID;
+
+	if (param->u.crypt.idx > max_idx) {
+		netdev_err(dev, "Error crypt.idx %d > %d\n", param->u.crypt.idx, max_idx);
+		ret = -EINVAL;
+		goto exit;
 	}
 
 	if (strcmp(param->u.crypt.alg, "WEP") == 0) {
@@ -98,9 +102,6 @@
 		wep_key_idx = param->u.crypt.idx;
 		wep_key_len = param->u.crypt.key_len;
 
-		if (wep_key_idx > WEP_KEYS)
-			return -EINVAL;
-
 		if (wep_key_len > 0) {
 			wep_key_len = wep_key_len <= 5 ? 5 : 13;
 			wep_total_len = wep_key_len + FIELD_OFFSET(struct ndis_802_11_wep, key_material);
@@ -153,7 +154,7 @@
 
 		if (check_fwstate(pmlmepriv, WIFI_STATION_STATE | WIFI_MP_STATE) == true) { /* sta mode */
 			psta = rtw_get_stainfo(pstapriv, get_bssid(pmlmepriv));
-			if (psta == NULL) {
+			if (!psta) {
 				/* DEBUG_ERR(("Set wpa_set_encryption: Obtain Sta_info fail\n")); */
 			} else {
 				/* Jeff: don't disable ieee8021x_blocked while clearing key */
@@ -206,7 +207,7 @@
 			}
 
 			pbcmc_sta = rtw_get_bcmc_stainfo(padapter);
-			if (pbcmc_sta == NULL) {
+			if (!pbcmc_sta) {
 				/* DEBUG_ERR(("Set OID_802_11_ADD_KEY: bcmc stainfo is null\n")); */
 			} else {
 				/* Jeff: don't disable ieee8021x_blocked while clearing key */
@@ -236,9 +237,9 @@
 	int ret = 0;
 	u8 null_addr[] = {0, 0, 0, 0, 0, 0};
 
-	if ((ielen > MAX_WPA_IE_LEN) || (pie == NULL)) {
+	if (ielen > MAX_WPA_IE_LEN || !pie) {
 		_clr_fwstate_(&padapter->mlmepriv, WIFI_UNDER_WPS);
-		if (pie == NULL)
+		if (!pie)
 			return ret;
 		else
 			return -EINVAL;
@@ -246,7 +247,7 @@
 
 	if (ielen) {
 		buf = rtw_zmalloc(ielen);
-		if (buf == NULL) {
+		if (!buf) {
 			ret =  -ENOMEM;
 			goto exit;
 		}
@@ -491,7 +492,7 @@
 		return -EINVAL;
 
 	param = rtw_malloc(p->length);
-	if (param == NULL)
+	if (!param)
 		return -ENOMEM;
 
 	if (copy_from_user(param, p->pointer, p->length)) {
@@ -571,7 +572,7 @@
 			goto exit;
 	}
 
-	if (strcmp(param->u.crypt.alg, "none") == 0 && (psta == NULL)) {
+	if (strcmp(param->u.crypt.alg, "none") == 0 && !psta) {
 		/* todo:clear default encryption keys */
 
 		psecuritypriv->dot11AuthAlgrthm = dot11AuthAlgrthm_Open;
@@ -583,7 +584,7 @@
 	}
 
 
-	if (strcmp(param->u.crypt.alg, "WEP") == 0 && (psta == NULL)) {
+	if (strcmp(param->u.crypt.alg, "WEP") == 0 && !psta) {
 		wep_key_idx = param->u.crypt.idx;
 		wep_key_len = param->u.crypt.key_len;
 
@@ -835,9 +836,7 @@
 	psta = rtw_get_stainfo(pstapriv, param->sta_addr);
 	if (psta)
 	{
-		spin_lock_bh(&(pstapriv->sta_hash_lock));
 		rtw_free_stainfo(padapter,  psta);
-		spin_unlock_bh(&(pstapriv->sta_hash_lock));
 
 		psta = NULL;
 	}
@@ -1229,7 +1228,7 @@
 		return -EINVAL;
 
 	param = rtw_malloc(p->length);
-	if (param == NULL)
+	if (!param)
 		return -ENOMEM;
 
 	if (copy_from_user(param, p->pointer, p->length)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/rtl8723bs/os_dep/os_intfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/rtl8723bs/os_dep/os_intfs.c
@@ -488,7 +488,7 @@
 
 	padapter = dvobj->padapters;
 
-	if (padapter == NULL)
+	if (!padapter)
 		return;
 
 	pnetdev = padapter->pnetdev;
@@ -594,7 +594,7 @@
 	struct dvobj_priv *pdvobj = NULL;
 
 	pdvobj = rtw_zmalloc(sizeof(*pdvobj));
-	if (pdvobj == NULL)
+	if (!pdvobj)
 		return NULL;
 
 	mutex_init(&pdvobj->hw_init_mutex);
@@ -664,51 +664,36 @@
 
 u8 rtw_init_drv_sw(struct adapter *padapter)
 {
-	u8 ret8 = _SUCCESS;
-
 	rtw_init_default_value(padapter);
 
 	rtw_init_hal_com_default_value(padapter);
 
-	if (rtw_init_cmd_priv(&padapter->cmdpriv)) {
-		ret8 = _FAIL;
-		goto exit;
-	}
+	if (rtw_init_cmd_priv(&padapter->cmdpriv))
+		return _FAIL;
 
 	padapter->cmdpriv.padapter = padapter;
 
-	if (rtw_init_evt_priv(&padapter->evtpriv)) {
-		ret8 = _FAIL;
-		goto exit;
-	}
-
+	if (rtw_init_evt_priv(&padapter->evtpriv))
+		goto free_cmd_priv;
 
-	if (rtw_init_mlme_priv(padapter) == _FAIL) {
-		ret8 = _FAIL;
-		goto exit;
-	}
+	if (rtw_init_mlme_priv(padapter) == _FAIL)
+		goto free_evt_priv;
 
 	init_mlme_ext_priv(padapter);
 
-	if (_rtw_init_xmit_priv(&padapter->xmitpriv, padapter) == _FAIL) {
-		ret8 = _FAIL;
-		goto exit;
-	}
-
-	if (_rtw_init_recv_priv(&padapter->recvpriv, padapter) == _FAIL) {
-		ret8 = _FAIL;
-		goto exit;
-	}
+	if (_rtw_init_xmit_priv(&padapter->xmitpriv, padapter) == _FAIL)
+		goto free_mlme_ext;
+
+	if (_rtw_init_recv_priv(&padapter->recvpriv, padapter) == _FAIL)
+		goto free_xmit_priv;
 	/*  add for CONFIG_IEEE80211W, none 11w also can use */
 	spin_lock_init(&padapter->security_key_mutex);
 
 	/*  We don't need to memset padapter->XXX to zero, because adapter is allocated by vzalloc(). */
 	/* memset((unsigned char *)&padapter->securitypriv, 0, sizeof (struct security_priv)); */
 
-	if (_rtw_init_sta_priv(&padapter->stapriv) == _FAIL) {
-		ret8 = _FAIL;
-		goto exit;
-	}
+	if (_rtw_init_sta_priv(&padapter->stapriv) == _FAIL)
+		goto free_recv_priv;
 
 	padapter->stapriv.padapter = padapter;
 	padapter->setband = GHZ24_50;
@@ -719,9 +704,26 @@
 
 	rtw_hal_dm_init(padapter);
 
-exit:
+	return _SUCCESS;
+
+free_recv_priv:
+	_rtw_free_recv_priv(&padapter->recvpriv);
+
+free_xmit_priv:
+	_rtw_free_xmit_priv(&padapter->xmitpriv);
+
+free_mlme_ext:
+	free_mlme_ext_priv(&padapter->mlmeextpriv);
+
+	rtw_free_mlme_priv(&padapter->mlmepriv);
+
+free_evt_priv:
+	rtw_free_evt_priv(&padapter->evtpriv);
+
+free_cmd_priv:
+	rtw_free_cmd_priv(&padapter->cmdpriv);
 
-	return ret8;
+	return _FAIL;
 }
 
 void rtw_cancel_all_timer(struct adapter *padapter)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/uartlite-rs485/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/uartlite-rs485/Kconfig
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Uartlite RS485 Serial device configuration
+#
+
+config SERIAL_UARTLITE_RS485
+	tristate "Xilinx uartlite rs485 serial port support"
+	depends on HAS_IOMEM
+	select SERIAL_CORE
+	help
+	  Say Y here if you want to use the Xilinx uartlite with rs485 serial controller.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called uartlite_485.
+
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/uartlite-rs485/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/uartlite-rs485/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the kernel serial device drivers.
+#
+
+obj-$(CONFIG_SERIAL_UARTLITE_RS485) += uartlite-rs485.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/uartlite-rs485/uartlite-rs485.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/uartlite-rs485/uartlite-rs485.c
@@ -0,0 +1,718 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * uartlite.c: Serial driver for Xilinx uartlite serial controller
+ *
+ * Copyright (C) 2006 Peter Korsgaard <jacmet@sunsite.dk>
+ * Copyright (C) 2007 Secret Lab Technologies Ltd.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/console.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/pm_runtime.h>
+
+#define ULITE_NAME		"ttyULR"
+#define ULITE_DRV_NAME		"uartlite_rs485"
+#define ULITE_MAJOR		205
+#define ULITE_MINOR		187
+#define ULITE_NR_UARTS		CONFIG_SERIAL_UARTLITE_NR_UARTS
+
+/* ---------------------------------------------------------------------
+ * Register definitions
+ *
+ * For register details see datasheet:
+ * https://www.xilinx.com/support/documentation/ip_documentation/opb_uartlite.pdf
+ */
+
+#define ULITE_RX		0x00
+#define ULITE_TX		0x04
+#define ULITE_STATUS		0x08
+#define ULITE_CONTROL		0x0c
+
+#define ULITE_REGION		16
+
+#define ULITE_STATUS_RXVALID	0x01
+#define ULITE_STATUS_RXFULL	0x02
+#define ULITE_STATUS_TXEMPTY	0x04
+#define ULITE_STATUS_TXFULL	0x08
+#define ULITE_STATUS_IE		0x10
+#define ULITE_STATUS_OVERRUN	0x20
+#define ULITE_STATUS_FRAME	0x40
+#define ULITE_STATUS_PARITY	0x80
+
+#define ULITE_CONTROL_RST_TX	0x01
+#define ULITE_CONTROL_RST_RX	0x02
+#define ULITE_CONTROL_IE	0x10
+#define UART_AUTOSUSPEND_TIMEOUT	3000	/* ms */
+
+struct uartlite_data {
+	const struct uartlite_reg_ops *reg_ops;
+	struct clk *clk;
+};
+
+struct uartlite_reg_ops {
+	u32 (*in)(void __iomem *addr);
+	void (*out)(u32 val, void __iomem *addr);
+};
+
+static u32 uartlite_inbe32(void __iomem *addr)
+{
+	return ioread32be(addr);
+}
+
+static void uartlite_outbe32(u32 val, void __iomem *addr)
+{
+	iowrite32be(val, addr);
+}
+
+static const struct uartlite_reg_ops uartlite_be = {
+	.in = uartlite_inbe32,
+	.out = uartlite_outbe32,
+};
+
+static u32 uartlite_inle32(void __iomem *addr)
+{
+	return ioread32(addr);
+}
+
+static void uartlite_outle32(u32 val, void __iomem *addr)
+{
+	iowrite32(val, addr);
+}
+
+static const struct uartlite_reg_ops uartlite_le = {
+	.in = uartlite_inle32,
+	.out = uartlite_outle32,
+};
+
+static inline u32 uart_in32(u32 offset, struct uart_port *port)
+{
+	struct uartlite_data *pdata = port->private_data;
+
+	return pdata->reg_ops->in(port->membase + offset);
+}
+
+static inline void uart_out32(u32 val, u32 offset, struct uart_port *port)
+{
+	struct uartlite_data *pdata = port->private_data;
+
+	pdata->reg_ops->out(val, port->membase + offset);
+}
+
+static struct uart_port ulite_ports[ULITE_NR_UARTS];
+
+/* ---------------------------------------------------------------------
+ * Core UART driver operations
+ */
+
+static int ulite_receive(struct uart_port *port, int stat)
+{
+	struct tty_port *tport = &port->state->port;
+	unsigned char ch = 0;
+	char flag = TTY_NORMAL;
+
+	if ((stat & (ULITE_STATUS_RXVALID | ULITE_STATUS_OVERRUN
+		     | ULITE_STATUS_FRAME)) == 0)
+		return 0;
+
+	/* stats */
+	if (stat & ULITE_STATUS_RXVALID) {
+		port->icount.rx++;
+		ch = uart_in32(ULITE_RX, port);
+
+		if (stat & ULITE_STATUS_PARITY)
+			port->icount.parity++;
+	}
+
+	if (stat & ULITE_STATUS_OVERRUN)
+		port->icount.overrun++;
+
+	if (stat & ULITE_STATUS_FRAME)
+		port->icount.frame++;
+
+	/* drop byte with parity error if IGNPAR specified */
+	if (stat & port->ignore_status_mask & ULITE_STATUS_PARITY)
+		stat &= ~ULITE_STATUS_RXVALID;
+
+	stat &= port->read_status_mask;
+
+	if (stat & ULITE_STATUS_PARITY)
+		flag = TTY_PARITY;
+
+	stat &= ~port->ignore_status_mask;
+
+	if (stat & ULITE_STATUS_RXVALID)
+		tty_insert_flip_char(tport, ch, flag);
+
+	if (stat & ULITE_STATUS_FRAME)
+		tty_insert_flip_char(tport, 0, TTY_FRAME);
+
+	if (stat & ULITE_STATUS_OVERRUN)
+		tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+
+	return 1;
+}
+
+static int ulite_transmit(struct uart_port *port, int stat)
+{
+	struct circ_buf *xmit  = &port->state->xmit;
+
+	if (stat & ULITE_STATUS_TXFULL)
+		return 0;
+
+	if (port->x_char) {
+		uart_out32(port->x_char, ULITE_TX, port);
+		port->x_char = 0;
+		port->icount.tx++;
+		return 1;
+	}
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+		return 0;
+
+	uart_out32(xmit->buf[xmit->tail], ULITE_TX, port);
+	xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+	port->icount.tx++;
+
+	/* wake up */
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	return 1;
+}
+
+static irqreturn_t ulite_isr(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	int stat, busy, n = 0;
+	unsigned long flags;
+
+	do {
+		spin_lock_irqsave(&port->lock, flags);
+		stat = uart_in32(ULITE_STATUS, port);
+		busy  = ulite_receive(port, stat);
+		busy |= ulite_transmit(port, stat);
+		spin_unlock_irqrestore(&port->lock, flags);
+		n++;
+	} while (busy);
+
+	/* work done? */
+	if (n > 1) {
+		tty_flip_buffer_push(&port->state->port);
+		return IRQ_HANDLED;
+	} else {
+		return IRQ_NONE;
+	}
+}
+
+static unsigned int ulite_tx_empty(struct uart_port *port)
+{
+	unsigned long flags;
+	unsigned int ret;
+
+	spin_lock_irqsave(&port->lock, flags);
+	ret = uart_in32(ULITE_STATUS, port);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return ret & ULITE_STATUS_TXEMPTY ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int ulite_get_mctrl(struct uart_port *port)
+{
+	return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void ulite_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	/* N/A */
+}
+
+static void ulite_stop_tx(struct uart_port *port)
+{
+	/* N/A */
+}
+
+static void ulite_start_tx(struct uart_port *port)
+{
+	ulite_transmit(port, uart_in32(ULITE_STATUS, port));
+}
+
+static void ulite_stop_rx(struct uart_port *port)
+{
+	/* don't forward any more data (like !CREAD) */
+	port->ignore_status_mask = ULITE_STATUS_RXVALID | ULITE_STATUS_PARITY
+		| ULITE_STATUS_FRAME | ULITE_STATUS_OVERRUN;
+}
+
+static void ulite_break_ctl(struct uart_port *port, int ctl)
+{
+	/* N/A */
+}
+
+static int ulite_startup(struct uart_port *port)
+{
+	struct uartlite_data *pdata = port->private_data;
+	int ret;
+
+	ret = clk_enable(pdata->clk);
+	if (ret) {
+		dev_err(port->dev, "Failed to enable clock\n");
+		return ret;
+	}
+
+	ret = request_irq(port->irq, ulite_isr, IRQF_SHARED | IRQF_TRIGGER_RISING,
+			  ULITE_DRV_NAME, port);
+	if (ret)
+		return ret;
+
+	uart_out32(ULITE_CONTROL_RST_RX | ULITE_CONTROL_RST_TX,
+		   ULITE_CONTROL, port);
+	uart_out32(ULITE_CONTROL_IE, ULITE_CONTROL, port);
+
+	return 0;
+}
+
+static void ulite_shutdown(struct uart_port *port)
+{
+	struct uartlite_data *pdata = port->private_data;
+
+	uart_out32(0, ULITE_CONTROL, port);
+	free_irq(port->irq, port);
+	clk_disable(pdata->clk);
+}
+
+static void ulite_set_termios(struct uart_port *port, struct ktermios *termios,
+			      struct ktermios *old)
+{
+	unsigned long flags;
+	unsigned int baud;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	port->read_status_mask = ULITE_STATUS_RXVALID | ULITE_STATUS_OVERRUN
+		| ULITE_STATUS_TXFULL;
+
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |=
+			ULITE_STATUS_PARITY | ULITE_STATUS_FRAME;
+
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= ULITE_STATUS_PARITY
+			| ULITE_STATUS_FRAME | ULITE_STATUS_OVERRUN;
+
+	/* ignore all characters if CREAD is not set */
+	if ((termios->c_cflag & CREAD) == 0)
+		port->ignore_status_mask |=
+			ULITE_STATUS_RXVALID | ULITE_STATUS_PARITY
+			| ULITE_STATUS_FRAME | ULITE_STATUS_OVERRUN;
+
+	/* update timeout */
+	baud = uart_get_baud_rate(port, termios, old, 0, 460800);
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *ulite_type(struct uart_port *port)
+{
+	return port->type == PORT_UARTLITE ? ULITE_DRV_NAME : NULL;
+}
+
+static void ulite_release_port(struct uart_port *port)
+{
+	release_mem_region(port->mapbase, ULITE_REGION);
+	iounmap(port->membase);
+	port->membase = NULL;
+}
+
+static int ulite_request_port(struct uart_port *port)
+{
+	struct uartlite_data *pdata = port->private_data;
+	int ret;
+
+	pr_debug("ulite console: port=%p; port->mapbase=%llx\n",
+		 port, (unsigned long long)port->mapbase);
+
+	if (!request_mem_region(port->mapbase, ULITE_REGION, ULITE_DRV_NAME)) {
+		dev_err(port->dev, "Memory region busy\n");
+		return -EBUSY;
+	}
+
+	port->membase = ioremap(port->mapbase, ULITE_REGION);
+	if (!port->membase) {
+		dev_err(port->dev, "Unable to map registers\n");
+		release_mem_region(port->mapbase, ULITE_REGION);
+		return -EBUSY;
+	}
+
+	pdata->reg_ops = &uartlite_be;
+	uart_out32(ULITE_CONTROL_RST_TX, ULITE_CONTROL, port);
+	ret = uart_in32(ULITE_STATUS, port);
+	/* Endianness detection */
+	if ((ret & ULITE_STATUS_TXEMPTY) != ULITE_STATUS_TXEMPTY)
+		pdata->reg_ops = &uartlite_le;
+
+	return 0;
+}
+
+static void ulite_config_port(struct uart_port *port, int flags)
+{
+	if (!ulite_request_port(port))
+		port->type = PORT_UARTLITE;
+}
+
+static int ulite_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	/* we don't want the core code to modify any port params */
+	return -EINVAL;
+}
+
+static void ulite_pm(struct uart_port *port, unsigned int state,
+		     unsigned int oldstate)
+{
+	int ret;
+
+	if (!state) {
+		ret = pm_runtime_get_sync(port->dev);
+		if (ret < 0)
+			dev_err(port->dev, "Failed to enable clocks\n");
+	} else {
+		pm_runtime_mark_last_busy(port->dev);
+		pm_runtime_put_autosuspend(port->dev);
+	}
+}
+
+static int ulite_config_rs485(struct uart_port *port,
+			      struct ktermios *termios,
+			      struct serial_rs485 *rs485conf)
+{
+	port->rs485 = *rs485conf;
+
+	if (rs485conf->flags & SER_RS485_ENABLED)
+		dev_dbg(port->dev, "Setting UART to RS485\n");
+	else
+		dev_dbg(port->dev, "Setting UART to RS232\n");
+
+	return 0;
+}
+
+static const struct uart_ops ulite_ops = {
+	.tx_empty	= ulite_tx_empty,
+	.set_mctrl	= ulite_set_mctrl,
+	.get_mctrl	= ulite_get_mctrl,
+	.stop_tx	= ulite_stop_tx,
+	.start_tx	= ulite_start_tx,
+	.stop_rx	= ulite_stop_rx,
+	.break_ctl	= ulite_break_ctl,
+	.startup	= ulite_startup,
+	.shutdown	= ulite_shutdown,
+	.set_termios	= ulite_set_termios,
+	.type		= ulite_type,
+	.release_port	= ulite_release_port,
+	.request_port	= ulite_request_port,
+	.config_port	= ulite_config_port,
+	.verify_port	= ulite_verify_port,
+	.pm		= ulite_pm,
+};
+
+static struct uart_driver ulite_uart_driver = {
+	.owner		= THIS_MODULE,
+	.driver_name	= ULITE_DRV_NAME,
+	.dev_name	= ULITE_NAME,
+	.major		= ULITE_MAJOR,
+	.minor		= ULITE_MINOR,
+	.nr		= ULITE_NR_UARTS,
+};
+
+/* ---------------------------------------------------------------------
+ * Port assignment functions (mapping devices to uart_port structures)
+ */
+
+/** ulite_assign: register a uartlite device with the driver
+ *
+ * @dev: pointer to device structure
+ * @id: requested id number.  Pass -1 for automatic port assignment
+ * @base: base address of uartlite registers
+ * @irq: irq number for uartlite
+ * @pdata: private data for uartlite
+ *
+ * Returns: 0 on success, <0 otherwise
+ */
+static int ulite_assign(struct device *dev, int id, phys_addr_t base, int irq,
+			struct uartlite_data *pdata)
+{
+	struct uart_port *port;
+	int rc;
+
+	/* if id = -1; then scan for a free id and use that */
+	if (id < 0) {
+		for (id = 0; id < ULITE_NR_UARTS; id++)
+			if (ulite_ports[id].mapbase == 0)
+				break;
+	}
+	if (id < 0 || id >= ULITE_NR_UARTS) {
+		dev_err(dev, "%s%i too large\n", ULITE_NAME, id);
+		return -EINVAL;
+	}
+
+	if ((ulite_ports[id].mapbase) && (ulite_ports[id].mapbase != base)) {
+		dev_err(dev, "cannot assign to %s%i; it is already in use\n",
+			ULITE_NAME, id);
+		return -EBUSY;
+	}
+
+	port = &ulite_ports[id];
+
+	spin_lock_init(&port->lock);
+	port->fifosize = 16;
+	port->regshift = 2;
+	port->iotype = UPIO_MEM;
+	port->iobase = 1; /* mark port in use */
+	port->mapbase = base;
+	port->membase = NULL;
+	port->ops = &ulite_ops;
+	port->irq = irq;
+	port->flags = UPF_BOOT_AUTOCONF;
+	port->dev = dev;
+	port->type = PORT_UNKNOWN;
+	port->line = id;
+	port->private_data = pdata;
+
+	port->rs485.flags |= SER_RS485_ENABLED;
+	port->rs485_config = ulite_config_rs485;
+
+	dev_set_drvdata(dev, port);
+
+	/* Register the port */
+	rc = uart_add_one_port(&ulite_uart_driver, port);
+	if (rc) {
+		dev_err(dev, "uart_add_one_port() failed; err=%i\n", rc);
+		port->mapbase = 0;
+		dev_set_drvdata(dev, NULL);
+		return rc;
+	}
+
+	return 0;
+}
+
+/** ulite_release: register a uartlite device with the driver
+ *
+ * @dev: pointer to device structure
+ */
+static int ulite_release(struct device *dev)
+{
+	struct uart_port *port = dev_get_drvdata(dev);
+	int rc = 0;
+
+	if (port) {
+		rc = uart_remove_one_port(&ulite_uart_driver, port);
+		dev_set_drvdata(dev, NULL);
+		port->mapbase = 0;
+	}
+
+	return rc;
+}
+
+/**
+ * ulite_suspend - Stop the device.
+ *
+ * @dev: handle to the device structure.
+ * Return: 0 always.
+ */
+static int __maybe_unused ulite_suspend(struct device *dev)
+{
+	struct uart_port *port = dev_get_drvdata(dev);
+
+	if (port)
+		uart_suspend_port(&ulite_uart_driver, port);
+
+	return 0;
+}
+
+/**
+ * ulite_resume - Resume the device.
+ *
+ * @dev: handle to the device structure.
+ * Return: 0 on success, errno otherwise.
+ */
+static int __maybe_unused ulite_resume(struct device *dev)
+{
+	struct uart_port *port = dev_get_drvdata(dev);
+
+	if (port)
+		uart_resume_port(&ulite_uart_driver, port);
+
+	return 0;
+}
+
+static int __maybe_unused ulite_runtime_suspend(struct device *dev)
+{
+	struct uart_port *port = dev_get_drvdata(dev);
+	struct uartlite_data *pdata = port->private_data;
+
+	clk_disable(pdata->clk);
+	return 0;
+};
+
+static int __maybe_unused ulite_runtime_resume(struct device *dev)
+{
+	struct uart_port *port = dev_get_drvdata(dev);
+	struct uartlite_data *pdata = port->private_data;
+	int ret;
+
+	ret = clk_enable(pdata->clk);
+	if (ret) {
+		dev_err(dev, "Cannot enable clock.\n");
+		return ret;
+	}
+	return 0;
+}
+
+/* ---------------------------------------------------------------------
+ * Platform bus binding
+ */
+
+static const struct dev_pm_ops ulite_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(ulite_suspend, ulite_resume)
+	SET_RUNTIME_PM_OPS(ulite_runtime_suspend,
+			   ulite_runtime_resume, NULL)
+};
+
+#if defined(CONFIG_OF)
+/* Match table for of_platform binding */
+static const struct of_device_id ulite_of_match[] = {
+	{ .compatible = "xlnx,axi-uartlite-rs485", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, ulite_of_match);
+#endif /* CONFIG_OF */
+
+static int ulite_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct uartlite_data *pdata;
+	int irq, ret;
+	int id = pdev->id;
+#ifdef CONFIG_OF
+	const __be32 *prop;
+
+	prop = of_get_property(pdev->dev.of_node, "port-number", NULL);
+	if (prop)
+		id = be32_to_cpup(prop);
+#endif
+	pdata = devm_kzalloc(&pdev->dev, sizeof(struct uartlite_data),
+			     GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	pdata->clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+	if (IS_ERR(pdata->clk)) {
+		if (PTR_ERR(pdata->clk) != -ENOENT)
+			return PTR_ERR(pdata->clk);
+
+		/*
+		 * Clock framework support is optional, continue on
+		 * anyways if we don't find a matching clock.
+		 */
+		pdata->clk = NULL;
+	}
+
+	ret = clk_prepare_enable(pdata->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to prepare clock\n");
+		return ret;
+	}
+
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
+	if (!ulite_uart_driver.state) {
+		dev_dbg(&pdev->dev, "uartlite: calling uart_register_driver()\n");
+		ret = uart_register_driver(&ulite_uart_driver);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "Failed to register driver\n");
+			clk_disable_unprepare(pdata->clk);
+			return ret;
+		}
+	}
+
+	ret = ulite_assign(&pdev->dev, id, res->start, irq, pdata);
+
+	pm_runtime_mark_last_busy(&pdev->dev);
+	pm_runtime_put_autosuspend(&pdev->dev);
+
+	return ret;
+}
+
+static int ulite_remove(struct platform_device *pdev)
+{
+	struct uart_port *port = dev_get_drvdata(&pdev->dev);
+	struct uartlite_data *pdata = port->private_data;
+	int rc;
+
+	clk_disable_unprepare(pdata->clk);
+	rc = ulite_release(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	return rc;
+}
+
+static struct platform_driver ulite_platform_driver = {
+	.probe = ulite_probe,
+	.remove = ulite_remove,
+	.driver = {
+		.name  = ULITE_DRV_NAME,
+		.of_match_table = of_match_ptr(ulite_of_match),
+		.pm = &ulite_pm_ops,
+	},
+};
+
+/* ---------------------------------------------------------------------
+ * Module setup/teardown
+ */
+
+static int __init ulite_init(void)
+{
+	pr_debug("uartlite: calling platform_driver_register()\n");
+	return platform_driver_register(&ulite_platform_driver);
+}
+
+static void __exit ulite_exit(void)
+{
+	platform_driver_unregister(&ulite_platform_driver);
+	if (ulite_uart_driver.state)
+		uart_unregister_driver(&ulite_uart_driver);
+}
+
+module_init(ulite_init);
+module_exit(ulite_exit);
+
+MODULE_AUTHOR("Peter Korsgaard <jacmet@sunsite.dk>");
+MODULE_DESCRIPTION("Xilinx uartlite serial driver");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/vc04_services/include/linux/raspberrypi/vchiq.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/vc04_services/include/linux/raspberrypi/vchiq.h
@@ -82,7 +82,7 @@
 
 struct vchiq_instance;
 
-extern enum vchiq_status vchiq_initialise(struct vchiq_instance **pinstance);
+extern int vchiq_initialise(struct vchiq_instance **pinstance);
 extern enum vchiq_status vchiq_shutdown(struct vchiq_instance *instance);
 extern enum vchiq_status vchiq_connect(struct vchiq_instance *instance);
 extern enum vchiq_status vchiq_open_service(struct vchiq_instance *instance,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
@@ -1033,15 +1033,27 @@
 
 	DEBUG_TRACE(SERVICE_CALLBACK_LINE);
 
+	rcu_read_lock();
 	service = handle_to_service(handle);
-	if (WARN_ON(!service))
+	if (WARN_ON(!service)) {
+		rcu_read_unlock();
 		return VCHIQ_SUCCESS;
+	}
 
 	user_service = (struct user_service *)service->base.userdata;
 	instance = user_service->instance;
 
-	if (!instance || instance->closing)
+	if (!instance || instance->closing) {
+		rcu_read_unlock();
 		return VCHIQ_SUCCESS;
+	}
+
+	/*
+	 * As hopping around different synchronization mechanism,
+	 * taking an extra reference results in simpler implementation.
+	 */
+	vchiq_service_get(service);
+	rcu_read_unlock();
 
 	vchiq_log_trace(vchiq_arm_log_level,
 		"%s - service %lx(%d,%p), reason %d, header %lx, instance %lx, bulk_userdata %lx",
@@ -1074,6 +1086,7 @@
 					NULL, user_service, bulk_userdata);
 				if (status != VCHIQ_SUCCESS) {
 					DEBUG_TRACE(SERVICE_CALLBACK_LINE);
+					vchiq_service_put(service);
 					return status;
 				}
 			}
@@ -1084,11 +1097,13 @@
 				vchiq_log_info(vchiq_arm_log_level,
 					"%s interrupted", __func__);
 				DEBUG_TRACE(SERVICE_CALLBACK_LINE);
+				vchiq_service_put(service);
 				return VCHIQ_RETRY;
 			} else if (instance->closing) {
 				vchiq_log_info(vchiq_arm_log_level,
 					"%s closing", __func__);
 				DEBUG_TRACE(SERVICE_CALLBACK_LINE);
+				vchiq_service_put(service);
 				return VCHIQ_ERROR;
 			}
 			DEBUG_TRACE(SERVICE_CALLBACK_LINE);
@@ -1117,6 +1132,7 @@
 		header = NULL;
 	}
 	DEBUG_TRACE(SERVICE_CALLBACK_LINE);
+	vchiq_service_put(service);
 
 	if (skip_completion)
 		return VCHIQ_SUCCESS;
@@ -1173,6 +1189,9 @@
 	int len;
 	int i;
 
+	if (!state)
+		return -ENOTCONN;
+
 	/*
 	 * There is no list of instances, so instead scan all services,
 	 * marking those that have been dumped.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.h
@@ -152,10 +152,10 @@
 vchiq_platform_get_arm_state(struct vchiq_state *state);
 
 
-extern enum vchiq_status
+extern int
 vchiq_use_internal(struct vchiq_state *state, struct vchiq_service *service,
 		   enum USE_TYPE_E use_type);
-extern enum vchiq_status
+extern int
 vchiq_release_internal(struct vchiq_state *state,
 		       struct vchiq_service *service);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_core.c
@@ -2421,6 +2421,9 @@
 	struct vchiq_service *service = find_service_by_handle(handle);
 	int pos;
 
+	if (!service)
+		return;
+
 	while (service->msg_queue_write == service->msg_queue_read +
 		VCHIQ_MAX_SLOTS) {
 		if (wait_for_completion_interruptible(&service->msg_queue_pop))
@@ -2441,6 +2444,9 @@
 	struct vchiq_header *header;
 	int pos;
 
+	if (!service)
+		return NULL;
+
 	if (service->msg_queue_write == service->msg_queue_read)
 		return NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c
@@ -940,8 +940,9 @@
 	/* build component create message */
 	m.h.type = MMAL_MSG_TYPE_COMPONENT_CREATE;
 	m.u.component_create.client_component = component->client_component;
-	strncpy(m.u.component_create.name, name,
-		sizeof(m.u.component_create.name));
+	strscpy_pad(m.u.component_create.name, name,
+		    sizeof(m.u.component_create.name));
+	m.u.component_create.pid = 0;
 
 	ret = send_synchronous_mmal_msg(instance, &m,
 					sizeof(m.u.component_create),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/vt6655/device_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/vt6655/device_main.c
@@ -565,7 +565,7 @@
 	kfree(desc->rd_info);
 
 err_free_desc:
-	while (--i) {
+	while (i--) {
 		desc = &priv->aRD0Ring[i];
 		device_free_rx_buf(priv, desc);
 		kfree(desc->rd_info);
@@ -611,7 +611,7 @@
 	kfree(desc->rd_info);
 
 err_free_desc:
-	while (--i) {
+	while (i--) {
 		desc = &priv->aRD1Ring[i];
 		device_free_rx_buf(priv, desc);
 		kfree(desc->rd_info);
@@ -676,7 +676,7 @@
 	return 0;
 
 err_free_desc:
-	while (--i) {
+	while (i--) {
 		desc = &priv->apTD0Rings[i];
 		kfree(desc->td_info);
 	}
@@ -716,7 +716,7 @@
 	return 0;
 
 err_free_desc:
-	while (--i) {
+	while (i--) {
 		desc = &priv->apTD1Rings[i];
 		kfree(desc->td_info);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/wfx/bus_sdio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/wfx/bus_sdio.c
@@ -120,19 +120,22 @@
 		return ret;
 	}
 
+	flags = irq_get_trigger_type(bus->of_irq);
+	if (!flags)
+		flags = IRQF_TRIGGER_HIGH;
+	flags |= IRQF_ONESHOT;
+	ret = devm_request_threaded_irq(&bus->func->dev, bus->of_irq, NULL,
+					wfx_sdio_irq_handler_ext, flags,
+					"wfx", bus);
+	if (ret)
+		return ret;
 	sdio_claim_host(bus->func);
 	cccr = sdio_f0_readb(bus->func, SDIO_CCCR_IENx, NULL);
 	cccr |= BIT(0);
 	cccr |= BIT(bus->func->num);
 	sdio_f0_writeb(bus->func, cccr, SDIO_CCCR_IENx, NULL);
 	sdio_release_host(bus->func);
-	flags = irq_get_trigger_type(bus->of_irq);
-	if (!flags)
-		flags = IRQF_TRIGGER_HIGH;
-	flags |= IRQF_ONESHOT;
-	return devm_request_threaded_irq(&bus->func->dev, bus->of_irq, NULL,
-					 wfx_sdio_irq_handler_ext, flags,
-					 "wfx", bus);
+	return 0;
 }
 
 static int wfx_sdio_irq_unsubscribe(void *priv)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/wfx/main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/wfx/main.c
@@ -309,7 +309,8 @@
 	wdev->pdata.gpio_wakeup = devm_gpiod_get_optional(dev, "wakeup",
 							  GPIOD_OUT_LOW);
 	if (IS_ERR(wdev->pdata.gpio_wakeup))
-		return NULL;
+		goto err;
+
 	if (wdev->pdata.gpio_wakeup)
 		gpiod_set_consumer_name(wdev->pdata.gpio_wakeup, "wfx wakeup");
 
@@ -328,6 +329,10 @@
 		return NULL;
 
 	return wdev;
+
+err:
+	ieee80211_free_hw(hw);
+	return NULL;
 }
 
 int wfx_probe(struct wfx_dev *wdev)
@@ -471,10 +476,23 @@
 {
 	int ret = 0;
 
-	if (IS_ENABLED(CONFIG_SPI))
+	if (IS_ENABLED(CONFIG_SPI)) {
 		ret = spi_register_driver(&wfx_spi_driver);
-	if (IS_ENABLED(CONFIG_MMC) && !ret)
+		if (ret)
+			goto out;
+	}
+	if (IS_ENABLED(CONFIG_MMC)) {
 		ret = sdio_register_driver(&wfx_sdio_driver);
+		if (ret)
+			goto unregister_spi;
+	}
+
+	return 0;
+
+unregister_spi:
+	if (IS_ENABLED(CONFIG_SPI))
+		spi_unregister_driver(&wfx_spi_driver);
+out:
 	return ret;
 }
 module_init(wfx_core_init);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/wlan-ng/hfa384x_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/wlan-ng/hfa384x_usb.c
@@ -3778,18 +3778,18 @@
 
 	spin_lock_irqsave(&hw->ctlxq.lock, flags);
 
-	/*
-	 * We need to check BOTH the RX and the TX throttle controls,
-	 * so we use the bitwise OR instead of the logical OR.
-	 */
 	pr_debug("flags=0x%lx\n", hw->usb_flags);
-	if (!hw->wlandev->hwremoved &&
-	    ((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
-	      !test_and_set_bit(WORK_RX_RESUME, &hw->usb_flags)) |
-	     (test_and_clear_bit(THROTTLE_TX, &hw->usb_flags) &&
-	      !test_and_set_bit(WORK_TX_RESUME, &hw->usb_flags))
-	    )) {
-		schedule_work(&hw->usb_work);
+	if (!hw->wlandev->hwremoved) {
+		bool rx_throttle = test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
+				   !test_and_set_bit(WORK_RX_RESUME, &hw->usb_flags);
+		bool tx_throttle = test_and_clear_bit(THROTTLE_TX, &hw->usb_flags) &&
+				   !test_and_set_bit(WORK_TX_RESUME, &hw->usb_flags);
+		/*
+		 * We need to check BOTH the RX and the TX throttle controls,
+		 * so we use the bitwise OR instead of the logical OR.
+		 */
+		if (rx_throttle | tx_throttle)
+			schedule_work(&hw->usb_work);
 	}
 
 	spin_unlock_irqrestore(&hw->ctlxq.lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/Kconfig
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Xilinx device configuration
+#
+
+if NET_VENDOR_XILINX
+
+config AXIENET_HAS_TADMA
+	bool "AxiEthernet is configured with TADMA"
+	depends on XILINX_TSN
+	help
+	  When hardware is generated with Axi Ethernet with TADMA select this option.
+	  This driver enables Time Aware DMA to support TSN Qbv clause accurately.
+	  It is used to fetch schedule traffic.
+	  It contains one queue.
+
+config XILINX_TSN
+	bool "Enable Xilinx's TSN IP"
+	help
+	  Enable Xilinx's TSN IP.
+
+config XILINX_TSN_PTP
+	bool "Generate hardware packet timestamps using Xilinx's TSN IP"
+	depends on XILINX_TSN
+	select PTP_1588_CLOCK
+	default y
+	help
+	  Generate hardware packet timestamps. This is to facilitate IEEE 1588.
+
+config XILINX_TSN_QBV
+	bool "Support Qbv protocol in TSN"
+	depends on XILINX_TSN_PTP
+	select PTP_1588_CLOCK
+	default y
+	help
+	  Enables TSN Qbv protocol.
+
+config XILINX_TSN_SWITCH
+	bool "Support TSN switch"
+	depends on XILINX_TSN
+	select NET_SWITCHDEV
+	default y
+	help
+	  Enable Xilinx's TSN Switch support.
+
+config XILINX_TSN_QCI
+	bool "Support Qci protocol in TSN"
+	depends on XILINX_TSN_SWITCH
+	default y
+	help
+	  Enable TSN QCI protocol.
+
+config XILINX_TSN_CB
+	bool "Support CB protocol in TSN"
+	depends on XILINX_TSN_SWITCH
+	default y
+	help
+	  Enable TSN CB protocol support.
+
+config XILINX_TSN_QBR
+	bool "Support QBR protocol in TSN"
+	depends on XILINX_TSN_SWITCH
+	default y
+	help
+	  Enable TSN QBR protocol support.
+
+endif # NET_VENDOR_XILINX
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the Xilinx network device drivers.
+#
+
+xilinx_emac_tsn-objs := xilinx_axienet_main_tsn.o xilinx_axienet_mcdma_tsn.o
+obj-$(CONFIG_XILINX_TSN) += xilinx_tsn_ep.o xilinx_tsn_ep_ex.o xilinx_tsn_ip.o xilinx_emac_tsn.o
+obj-$(CONFIG_XILINX_TSN_PTP) += xilinx_tsn_ptp_xmit.o xilinx_tsn_ptp_clock.o
+obj-$(CONFIG_XILINX_TSN_QBV) += xilinx_tsn_shaper.o
+obj-$(CONFIG_XILINX_TSN_QCI) += xilinx_tsn_qci.o
+obj-$(CONFIG_XILINX_TSN_CB) += xilinx_tsn_cb.o
+obj-$(CONFIG_XILINX_TSN_SWITCH) += xilinx_tsn_switch.o xilinx_tsn_switchdev.o
+obj-$(CONFIG_XILINX_TSN_QBR) += xilinx_tsn_preemption.o
+obj-$(CONFIG_AXIENET_HAS_TADMA) += xilinx_tsn_tadma.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_axienet_main_tsn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_axienet_main_tsn.c
@@ -0,0 +1,2033 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx Axi Ethernet device driver
+ *
+ * Copyright (c) 2008 Nissin Systems Co., Ltd.,  Yoshio Kashiwagi
+ * Copyright (c) 2005-2008 DLA Systems,  David H. Lynch Jr. <dhlii@dlasys.net>
+ * Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
+ * Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
+ * Copyright (c) 2010 - 2011 PetaLogix
+ * Copyright (c) 2019 SED Systems, a division of Calian Ltd.
+ * Copyright (c) 2010 - 2012 Xilinx, Inc. All rights reserved.
+ *
+ * This is a driver for the Xilinx Axi Ethernet which is used in the Virtex6
+ * and Spartan6.
+ *
+ * TODO:
+ *  - Add Axi Fifo support.
+ *  - Factor out Axi DMA code into separate driver.
+ *  - Test and fix basic multicast filtering.
+ *  - Add support for extended multicast filtering.
+ *  - Test basic VLAN support.
+ *  - Add support for extended VLAN support.
+ */
+
+#include <linux/clk.h>
+#include <linux/circ_buf.h>
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/phy.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/iopoll.h>
+#include <linux/ptp_classify.h>
+#include <linux/net_tstamp.h>
+#include <linux/random.h>
+#include <net/sock.h>
+#include <linux/xilinx_phy.h>
+#include <linux/clk.h>
+
+#include "xilinx_axienet_tsn.h"
+
+/* Descriptors defines for Tx and Rx DMA */
+#define TX_BD_NUM_DEFAULT		64
+#define RX_BD_NUM_DEFAULT		128
+#define TX_BD_NUM_MAX			4096
+#define RX_BD_NUM_MAX			4096
+
+/* Must be shorter than length of ethtool_drvinfo.driver field to fit */
+#define DRIVER_NAME		"xaxienet"
+#define DRIVER_DESCRIPTION	"Xilinx Axi Ethernet driver"
+#define DRIVER_VERSION		"1.00a"
+
+#define AXIENET_REGS_N		40
+#define AXIENET_TS_HEADER_LEN	8
+#define XXVENET_TS_HEADER_LEN	4
+#define MRMAC_TS_HEADER_LEN		16
+#define MRMAC_TS_HEADER_WORDS   (MRMAC_TS_HEADER_LEN / 4)
+#define NS_PER_SEC              1000000000ULL /* Nanoseconds per second */
+
+#define MRMAC_RESET_DELAY	1 /* Delay in msecs*/
+
+/* IEEE1588 Message Type field values  */
+#define PTP_TYPE_SYNC		0
+#define PTP_TYPE_PDELAY_REQ	2
+#define PTP_TYPE_PDELAY_RESP	3
+#define PTP_TYPE_OFFSET		42
+/* SW flags used to convey message type for command FIFO handling */
+#define MSG_TYPE_SHIFT			4
+#define MSG_TYPE_SYNC_FLAG		((PTP_TYPE_SYNC + 1) << MSG_TYPE_SHIFT)
+#define MSG_TYPE_PDELAY_RESP_FLAG	((PTP_TYPE_PDELAY_RESP + 1) << \
+									 MSG_TYPE_SHIFT)
+
+#define FILTER_SELECT		0x100	   /* Filter select */
+#define ETHERTYPE_FILTER_IPV4	0x00000008 /* Ethertype field 0x08 for IPv4 packets */
+#define ETHERTYPE_FILTER_PTP    0x0000F788 /* Ethertype field 0x88F7 for PTP packets */
+#define PROTO_FILTER_UDP	0x11000000 /* protocol field 0x11 for UDP packets */
+#define PTP_UDP_PORT		0x00003F01 /* dest port field 0x013F for PTP over UDP packes */
+#define PTP_VERSION		0x02000000 /* PTPv2 */
+
+#define DESTMAC_FILTER_ENABLE_MASK_MSB		0xFFFFFFFF /* Enable filtering for bytes 0-3 in a
+							    * packet corresponding to 4 Most
+							    * significant bytes of
+							    * Destination MAC address
+							    */
+#define DESTMAC_FILTER_ENABLE_MASK_LSB		0xFF000000 /* Enable filtering for bytes
+							    * 4-5 in a packet
+							    * corresponding to 2 Least
+							    * significant bytes of
+							    * Destination MAC address
+							    */
+#define PROTO_FILTER_DISABLE_MASK		0x0 /* Disable protocol based filtering */
+#define PORT_NUM_FILTER_DISABLE_MASK		0x0 /* Disable port number based filtering */
+#define VERSION_FILTER_DISABLE_MASK		0x0 /* Disable filtering based on PTP version */
+
+#define DESTMAC_FILTER_DISABLE_MASK_MSB		0 /* Disable Dest MAC address filtering(4 MSB'S) */
+#define DESTMAC_FILTER_DISABLE_MASK_LSB		0 /* Disable Dest MAC address filtering(2 LSB's) */
+#define PROTO_FILTER_ENABLE_MASK		0xFF000000 /* Enable protocol based filtering */
+#define PORT_NUM_FILTER_ENABLE_MASK		0x0000FFFF /* Enable port number based filtering */
+#define VERSION_FILTER_ENABLE_MASK		0xFF000000 /* Enable PTP version based filtering */
+
+#ifdef CONFIG_XILINX_TSN_PTP
+int axienet_phc_index = -1;
+EXPORT_SYMBOL(axienet_phc_index);
+#endif
+
+/* Option table for setting up Axi Ethernet hardware options */
+static struct axienet_option axienet_options[] = {
+	/* Turn on jumbo packet support for both Rx and Tx */
+	{
+		.opt = XAE_OPTION_JUMBO,
+		.reg = XAE_TC_OFFSET,
+		.m_or = XAE_TC_JUM_MASK,
+	}, {
+		.opt = XAE_OPTION_JUMBO,
+		.reg = XAE_RCW1_OFFSET,
+		.m_or = XAE_RCW1_JUM_MASK,
+	}, { /* Turn on VLAN packet support for both Rx and Tx */
+		.opt = XAE_OPTION_VLAN,
+		.reg = XAE_TC_OFFSET,
+		.m_or = XAE_TC_VLAN_MASK,
+	}, {
+		.opt = XAE_OPTION_VLAN,
+		.reg = XAE_RCW1_OFFSET,
+		.m_or = XAE_RCW1_VLAN_MASK,
+	}, { /* Turn on FCS stripping on receive packets */
+		.opt = XAE_OPTION_FCS_STRIP,
+		.reg = XAE_RCW1_OFFSET,
+		.m_or = XAE_RCW1_FCS_MASK,
+	}, { /* Turn on FCS insertion on transmit packets */
+		.opt = XAE_OPTION_FCS_INSERT,
+		.reg = XAE_TC_OFFSET,
+		.m_or = XAE_TC_FCS_MASK,
+	}, { /* Turn off length/type field checking on receive packets */
+		.opt = XAE_OPTION_LENTYPE_ERR,
+		.reg = XAE_RCW1_OFFSET,
+		.m_or = XAE_RCW1_LT_DIS_MASK,
+	}, { /* Turn on Rx flow control */
+		.opt = XAE_OPTION_FLOW_CONTROL,
+		.reg = XAE_FCC_OFFSET,
+		.m_or = XAE_FCC_FCRX_MASK,
+	}, { /* Turn on Tx flow control */
+		.opt = XAE_OPTION_FLOW_CONTROL,
+		.reg = XAE_FCC_OFFSET,
+		.m_or = XAE_FCC_FCTX_MASK,
+	}, { /* Turn on promiscuous frame filtering */
+		.opt = XAE_OPTION_PROMISC,
+		.reg = XAE_FMC_OFFSET,
+		.m_or = XAE_FMC_PM_MASK,
+	}, { /* Enable transmitter */
+		.opt = XAE_OPTION_TXEN,
+		.reg = XAE_TC_OFFSET,
+		.m_or = XAE_TC_TX_MASK,
+	}, { /* Enable receiver */
+		.opt = XAE_OPTION_RXEN,
+		.reg = XAE_RCW1_OFFSET,
+		.m_or = XAE_RCW1_RX_MASK,
+	},
+	{}
+};
+
+struct axienet_ethtools_stat {
+	const char *name;
+};
+
+static struct axienet_ethtools_stat axienet_get_ethtools_strings_stats[] = {
+	{ "tx_packets" },
+	{ "rx_packets" },
+	{ "tx_bytes" },
+	{ "rx_bytes" },
+	{ "tx_errors" },
+	{ "rx_errors" },
+};
+
+/**
+ * axienet_dma_bd_release_tsn - Release buffer descriptor rings
+ * @ndev:	Pointer to the net_device structure
+ *
+ * This function is used to release the descriptors allocated in
+ * axienet_dma_bd_init. axienet_dma_bd_release is called when Axi Ethernet
+ * driver stop api is called.
+ */
+void axienet_dma_bd_release_tsn(struct net_device *ndev)
+{
+	int i;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	for_each_tx_dma_queue(lp, i) {
+		axienet_mcdma_tx_bd_free_tsn(ndev, lp->dq[i]);
+	}
+	for_each_rx_dma_queue(lp, i) {
+		axienet_mcdma_rx_bd_free_tsn(ndev, lp->dq[i]);
+	}
+}
+
+/**
+ * axienet_set_mac_address_tsn - Write the MAC address
+ * @ndev:	Pointer to the net_device structure
+ * @address:	6 byte Address to be written as MAC address
+ *
+ * This function is called to initialize the MAC address of the Axi Ethernet
+ * core. It writes to the UAW0 and UAW1 registers of the core.
+ */
+void axienet_set_mac_address_tsn(struct net_device *ndev,
+				 const void *address)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (address)
+		ether_addr_copy(ndev->dev_addr, address);
+	if (!is_valid_ether_addr(ndev->dev_addr))
+		eth_hw_addr_random(ndev);
+
+	if (lp->axienet_config->mactype != XAXIENET_1G &&
+	    lp->axienet_config->mactype != XAXIENET_2_5G)
+		return;
+
+	/* Set up unicast MAC address filter set its mac address */
+	axienet_iow(lp, XAE_UAW0_OFFSET,
+		    (ndev->dev_addr[0]) |
+		    (ndev->dev_addr[1] << 8) |
+		    (ndev->dev_addr[2] << 16) |
+		    (ndev->dev_addr[3] << 24));
+	axienet_iow(lp, XAE_UAW1_OFFSET,
+		    (((axienet_ior(lp, XAE_UAW1_OFFSET)) &
+		      ~XAE_UAW1_UNICASTADDR_MASK) |
+		     (ndev->dev_addr[4] |
+		     (ndev->dev_addr[5] << 8))));
+}
+
+/**
+ * netdev_set_mac_address - Write the MAC address (from outside the driver)
+ * @ndev:	Pointer to the net_device structure
+ * @p:		6 byte Address to be written as MAC address
+ *
+ * Return: 0 for all conditions. Presently, there is no failure case.
+ *
+ * This function is called to initialize the MAC address of the Axi Ethernet
+ * core. It calls the core specific axienet_set_mac_address_tsn. This is the
+ * function that goes into net_device_ops structure entry ndo_set_mac_address.
+ */
+static int netdev_set_mac_address(struct net_device *ndev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	axienet_set_mac_address_tsn(ndev, addr->sa_data);
+	return 0;
+}
+
+/**
+ * axienet_set_multicast_list_tsn - Prepare the multicast table
+ * @ndev:	Pointer to the net_device structure
+ *
+ * This function is called to initialize the multicast table during
+ * initialization. The Axi Ethernet basic multicast support has a four-entry
+ * multicast table which is initialized here. Additionally this function
+ * goes into the net_device_ops structure entry ndo_set_multicast_list. This
+ * means whenever the multicast table entries need to be updated this
+ * function gets called.
+ */
+void axienet_set_multicast_list_tsn(struct net_device *ndev)
+{
+	int i;
+	u32 reg, af0reg, af1reg;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (lp->axienet_config->mactype != XAXIENET_1G || lp->eth_hasnobuf)
+		return;
+
+	if (ndev->flags & (IFF_ALLMULTI | IFF_PROMISC) ||
+	    netdev_mc_count(ndev) > XAE_MULTICAST_CAM_TABLE_NUM) {
+		/* We must make the kernel realize we had to move into
+		 * promiscuous mode. If it was a promiscuous mode request
+		 * the flag is already set. If not we set it.
+		 */
+		ndev->flags |= IFF_PROMISC;
+		reg = axienet_ior(lp, XAE_FMC_OFFSET);
+		reg |= XAE_FMC_PM_MASK;
+		axienet_iow(lp, XAE_FMC_OFFSET, reg);
+		dev_info(&ndev->dev, "Promiscuous mode enabled.\n");
+	} else if (!netdev_mc_empty(ndev)) {
+		struct netdev_hw_addr *ha;
+
+		i = 0;
+		netdev_for_each_mc_addr(ha, ndev) {
+			if (i >= XAE_MULTICAST_CAM_TABLE_NUM)
+				break;
+
+			af0reg = (ha->addr[0]);
+			af0reg |= (ha->addr[1] << 8);
+			af0reg |= (ha->addr[2] << 16);
+			af0reg |= (ha->addr[3] << 24);
+
+			af1reg = (ha->addr[4]);
+			af1reg |= (ha->addr[5] << 8);
+
+			reg = axienet_ior(lp, XAE_FMC_OFFSET) & 0xFFFFFF00;
+			reg |= i;
+
+			axienet_iow(lp, XAE_FMC_OFFSET, reg);
+			axienet_iow(lp, XAE_AF0_OFFSET, af0reg);
+			axienet_iow(lp, XAE_AF1_OFFSET, af1reg);
+			i++;
+		}
+	} else {
+		reg = axienet_ior(lp, XAE_FMC_OFFSET);
+		reg &= ~XAE_FMC_PM_MASK;
+
+		axienet_iow(lp, XAE_FMC_OFFSET, reg);
+
+		for (i = 0; i < XAE_MULTICAST_CAM_TABLE_NUM; i++) {
+			reg = axienet_ior(lp, XAE_FMC_OFFSET) & 0xFFFFFF00;
+			reg |= i;
+
+			axienet_iow(lp, XAE_FMC_OFFSET, reg);
+			axienet_iow(lp, XAE_AF0_OFFSET, 0);
+			axienet_iow(lp, XAE_AF1_OFFSET, 0);
+		}
+
+		dev_info(&ndev->dev, "Promiscuous mode disabled.\n");
+	}
+}
+
+/**
+ * axienet_setoptions_tsn - Set an Axi Ethernet option
+ * @ndev:	Pointer to the net_device structure
+ * @options:	Option to be enabled/disabled
+ *
+ * The Axi Ethernet core has multiple features which can be selectively turned
+ * on or off. The typical options could be jumbo frame option, basic VLAN
+ * option, promiscuous mode option etc. This function is used to set or clear
+ * these options in the Axi Ethernet hardware. This is done through
+ * axienet_option structure .
+ */
+void axienet_setoptions_tsn(struct net_device *ndev, u32 options)
+{
+	int reg;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_option *tp = &axienet_options[0];
+
+	while (tp->opt) {
+		reg = ((axienet_ior(lp, tp->reg)) & ~(tp->m_or));
+		if (options & tp->opt)
+			reg |= tp->m_or;
+		axienet_iow(lp, tp->reg, reg);
+		tp++;
+	}
+
+	lp->options |= options;
+}
+
+void __axienet_device_reset_tsn(struct axienet_dma_q *q)
+{
+	u32 timeout;
+	/* Reset Axi DMA. This would reset Axi Ethernet core as well. The reset
+	 * process of Axi DMA takes a while to complete as all pending
+	 * commands/transfers will be flushed or completed during this
+	 * reset process.
+	 * Note that even though both TX and RX have their own reset register,
+	 * they both reset the entire DMA core, so only one needs to be used.
+	 */
+	axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET, XAXIDMA_CR_RESET_MASK);
+	timeout = DELAY_OF_ONE_MILLISEC;
+	while (axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET) &
+				XAXIDMA_CR_RESET_MASK) {
+		udelay(1);
+		if (--timeout == 0) {
+			netdev_err(q->lp->ndev, "%s: DMA reset timeout!\n",
+				   __func__);
+			break;
+		}
+	}
+}
+
+/**
+ * axienet_adjust_link_tsn - Adjust the PHY link speed/duplex.
+ * @ndev:	Pointer to the net_device structure
+ *
+ * This function is called to change the speed and duplex setting after
+ * auto negotiation is done by the PHY. This is the function that gets
+ * registered with the PHY interface through the "of_phy_connect" call.
+ */
+void axienet_adjust_link_tsn(struct net_device *ndev)
+{
+	u32 emmc_reg;
+	u32 link_state;
+	u32 setspeed = 1;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct phy_device *phy = ndev->phydev;
+
+	link_state = phy->speed | (phy->duplex << 1) | phy->link;
+	if (lp->last_link != link_state) {
+		if (phy->speed == SPEED_10 || phy->speed == SPEED_100) {
+			if (lp->phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+				setspeed = 0;
+		} else {
+			if (phy->speed == SPEED_1000 &&
+			    lp->phy_mode == PHY_INTERFACE_MODE_MII)
+				setspeed = 0;
+		}
+
+		if (setspeed == 1) {
+			emmc_reg = axienet_ior(lp, XAE_EMMC_OFFSET);
+			emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
+
+			switch (phy->speed) {
+			case SPEED_2500:
+				emmc_reg |= XAE_EMMC_LINKSPD_2500;
+				break;
+			case SPEED_1000:
+				emmc_reg |= XAE_EMMC_LINKSPD_1000;
+				break;
+			case SPEED_100:
+				emmc_reg |= XAE_EMMC_LINKSPD_100;
+				break;
+			case SPEED_10:
+				emmc_reg |= XAE_EMMC_LINKSPD_10;
+				break;
+			default:
+				dev_err(&ndev->dev, "Speed other than 10, 100 ");
+				dev_err(&ndev->dev, "or 1Gbps is not supported\n");
+				break;
+			}
+
+			axienet_iow(lp, XAE_EMMC_OFFSET, emmc_reg);
+			phy_print_status(phy);
+		} else {
+			netdev_err(ndev,
+				   "Error setting Axi Ethernet mac speed\n");
+		}
+
+		lp->last_link = link_state;
+	}
+}
+
+/**
+ * axienet_start_xmit_done_tsn - Invoked once a transmit is completed by the
+ * Axi DMA Tx channel.
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * This function is invoked from the Axi DMA Tx isr to notify the completion
+ * of transmit operation. It clears fields in the corresponding Tx BDs and
+ * unmaps the corresponding buffer so that CPU can regain ownership of the
+ * buffer. It finally invokes "netif_wake_queue" to restart transmission if
+ * required.
+ */
+void axienet_start_xmit_done_tsn(struct net_device *ndev,
+				 struct axienet_dma_q *q)
+{
+	u32 size = 0;
+	u32 packets = 0;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct aximcdma_bd *cur_p;
+	unsigned int status = 0;
+
+	cur_p = &q->txq_bd_v[q->tx_bd_ci];
+	status = cur_p->sband_stats;
+	while (status & XAXIDMA_BD_STS_COMPLETE_MASK) {
+		if (cur_p->tx_desc_mapping == DESC_DMA_MAP_PAGE)
+			dma_unmap_page(ndev->dev.parent, cur_p->phys,
+				       cur_p->cntrl &
+				       XAXIDMA_BD_CTRL_LENGTH_MASK,
+				       DMA_TO_DEVICE);
+		else
+			dma_unmap_single(ndev->dev.parent, cur_p->phys,
+					 cur_p->cntrl &
+					 XAXIDMA_BD_CTRL_LENGTH_MASK,
+					 DMA_TO_DEVICE);
+		if (cur_p->tx_skb)
+			dev_kfree_skb_irq((struct sk_buff *)cur_p->tx_skb);
+		/*cur_p->phys = 0;*/
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app4 = 0;
+		cur_p->status = 0;
+		cur_p->tx_skb = 0;
+		cur_p->sband_stats = 0;
+
+		size += status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+		packets++;
+
+		if (++q->tx_bd_ci >= lp->tx_bd_num)
+			q->tx_bd_ci = 0;
+		cur_p = &q->txq_bd_v[q->tx_bd_ci];
+		status = cur_p->sband_stats;
+	}
+
+	ndev->stats.tx_packets += packets;
+	ndev->stats.tx_bytes += size;
+	q->tx_packets += packets;
+	q->tx_bytes += size;
+
+	/* Matches barrier in axienet_start_xmit */
+	smp_mb();
+
+	/* Fixme: With the existing multiqueue implementation
+	 * in the driver it is difficult to get the exact queue info.
+	 * We should wake only the particular queue
+	 * instead of waking all ndev queues.
+	 */
+	netif_tx_wake_all_queues(ndev);
+}
+
+/**
+ * axienet_check_tx_bd_space - Checks if a BD/group of BDs are currently busy
+ * @q:		Pointer to DMA queue structure
+ * @num_frag:	The number of BDs to check for
+ *
+ * Return: 0, on success
+ *	    NETDEV_TX_BUSY, if any of the descriptors are not free
+ *
+ * This function is invoked before BDs are allocated and transmission starts.
+ * This function returns 0 if a BD or group of BDs can be allocated for
+ * transmission. If the BD or any of the BDs are not free the function
+ * returns a busy status. This is invoked from axienet_start_xmit.
+ */
+static inline int axienet_check_tx_bd_space(struct axienet_dma_q *q,
+					    int num_frag)
+{
+	struct axienet_local *lp = q->lp;
+	struct aximcdma_bd *cur_p;
+
+	if (CIRC_SPACE(q->tx_bd_tail, q->tx_bd_ci, lp->tx_bd_num) < (num_frag + 1))
+		return NETDEV_TX_BUSY;
+
+	cur_p = &q->txq_bd_v[(q->tx_bd_tail + num_frag) % lp->tx_bd_num];
+	if (cur_p->sband_stats & XMCDMA_BD_STS_ALL_MASK)
+		return NETDEV_TX_BUSY;
+	return 0;
+}
+
+int axienet_queue_xmit_tsn(struct sk_buff *skb,
+			   struct net_device *ndev, u16 map)
+{
+	u32 ii;
+	u32 num_frag;
+	u32 csum_start_off;
+	u32 csum_index_off;
+	dma_addr_t tail_p;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct aximcdma_bd *cur_p;
+	unsigned long flags;
+	struct axienet_dma_q *q;
+
+	num_frag = skb_shinfo(skb)->nr_frags;
+
+	q = lp->dq[map];
+
+	cur_p = &q->txq_bd_v[q->tx_bd_tail];
+	spin_lock_irqsave(&q->tx_lock, flags);
+	if (axienet_check_tx_bd_space(q, num_frag)) {
+		if (netif_queue_stopped(ndev)) {
+			spin_unlock_irqrestore(&q->tx_lock, flags);
+			return NETDEV_TX_BUSY;
+		}
+
+		netif_stop_queue(ndev);
+
+		/* Matches barrier in axienet_start_xmit_done_tsn */
+		smp_mb();
+
+		/* Space might have just been freed - check again */
+		if (axienet_check_tx_bd_space(q, num_frag)) {
+			spin_unlock_irqrestore(&q->tx_lock, flags);
+			return NETDEV_TX_BUSY;
+		}
+
+		netif_wake_queue(ndev);
+	}
+
+	if (skb->ip_summed == CHECKSUM_PARTIAL && !lp->eth_hasnobuf &&
+	    lp->axienet_config->mactype == XAXIENET_1G) {
+		if (lp->features & XAE_FEATURE_FULL_TX_CSUM) {
+			/* Tx Full Checksum Offload Enabled */
+			cur_p->app0 |= 2;
+		} else if (lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) {
+			csum_start_off = skb_transport_offset(skb);
+			csum_index_off = csum_start_off + skb->csum_offset;
+			/* Tx Partial Checksum Offload Enabled */
+			cur_p->app0 |= 1;
+			cur_p->app1 = (csum_start_off << 16) | csum_index_off;
+		}
+	} else if (skb->ip_summed == CHECKSUM_UNNECESSARY &&
+		   !lp->eth_hasnobuf &&
+		   (lp->axienet_config->mactype == XAXIENET_1G)) {
+		cur_p->app0 |= 2; /* Tx Full Checksum Offload Enabled */
+	}
+
+	cur_p->cntrl = (skb_headlen(skb) | XMCDMA_BD_CTRL_TXSOF_MASK);
+
+	if (!q->eth_hasdre &&
+	    (((phys_addr_t)skb->data & 0x3) || num_frag > 0)) {
+		skb_copy_and_csum_dev(skb, q->tx_buf[q->tx_bd_tail]);
+
+		cur_p->phys = q->tx_bufs_dma +
+			      (q->tx_buf[q->tx_bd_tail] - q->tx_bufs);
+
+		cur_p->cntrl = skb_pagelen(skb) | XMCDMA_BD_CTRL_TXSOF_MASK;
+		goto out;
+	} else {
+		cur_p->phys = dma_map_single(ndev->dev.parent, skb->data,
+					     skb_headlen(skb), DMA_TO_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, cur_p->phys))) {
+			cur_p->phys = 0;
+			spin_unlock_irqrestore(&q->tx_lock, flags);
+			dev_err(&ndev->dev, "TX buffer map failed\n");
+			return NETDEV_TX_BUSY;
+		}
+	}
+	cur_p->tx_desc_mapping = DESC_DMA_MAP_SINGLE;
+
+	for (ii = 0; ii < num_frag; ii++) {
+		u32 len;
+		skb_frag_t *frag;
+
+		if (++q->tx_bd_tail >= lp->tx_bd_num)
+			q->tx_bd_tail = 0;
+
+		cur_p = &q->txq_bd_v[q->tx_bd_tail];
+		frag = &skb_shinfo(skb)->frags[ii];
+		len = skb_frag_size(frag);
+		cur_p->phys = skb_frag_dma_map(ndev->dev.parent, frag, 0, len,
+					       DMA_TO_DEVICE);
+		cur_p->cntrl = len;
+		cur_p->tx_desc_mapping = DESC_DMA_MAP_PAGE;
+	}
+
+out:
+	cur_p->cntrl |= XMCDMA_BD_CTRL_TXEOF_MASK;
+	tail_p = q->tx_bd_p + sizeof(*q->txq_bd_v) * q->tx_bd_tail;
+	cur_p->tx_skb = (phys_addr_t)skb;
+	cur_p->tx_skb = (phys_addr_t)skb;
+
+	tail_p = q->tx_bd_p + sizeof(*q->tx_bd_v) * q->tx_bd_tail;
+	/* Ensure BD write before starting transfer */
+	wmb();
+
+	/* Start the transfer */
+	axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id),
+			  tail_p);
+	if (++q->tx_bd_tail >= lp->tx_bd_num)
+		q->tx_bd_tail = 0;
+
+	spin_unlock_irqrestore(&q->tx_lock, flags);
+
+	return NETDEV_TX_OK;
+}
+
+/**
+ * axienet_recv - Is called from Axi DMA Rx Isr to complete the received
+ *		  BD processing.
+ * @ndev:	Pointer to net_device structure.
+ * @budget:	NAPI budget
+ * @q:		Pointer to axienet DMA queue structure
+ *
+ * This function is invoked from the Axi DMA Rx isr(poll) to process the Rx BDs
+ * It does minimal processing and invokes "netif_receive_skb" to complete
+ * further processing.
+ * Return: Number of BD's processed.
+ */
+static int axienet_recv(struct net_device *ndev, int budget,
+			struct axienet_dma_q *q)
+{
+	u32 length;
+	u32 csumstatus;
+	u32 size = 0;
+	u32 packets = 0;
+	dma_addr_t tail_p = 0;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct sk_buff *skb, *new_skb;
+	u32 sband_status = 0;
+	struct net_device *temp_ndev = NULL;
+	struct aximcdma_bd *cur_p;
+	unsigned int numbdfree = 0;
+
+	/* Get relevat BD status value */
+	rmb();
+	cur_p = &q->rxq_bd_v[q->rx_bd_ci];
+	sband_status = cur_p->sband_stats;
+
+	while ((numbdfree < budget) &&
+	       (cur_p->status & XAXIDMA_BD_STS_COMPLETE_MASK)) {
+		new_skb = netdev_alloc_skb(ndev, lp->max_frm_size);
+		if (!new_skb)
+			break;
+		tail_p = q->rx_bd_p + sizeof(*q->rxq_bd_v) * q->rx_bd_ci;
+
+		dma_unmap_single(ndev->dev.parent, cur_p->phys,
+				 lp->max_frm_size,
+				 DMA_FROM_DEVICE);
+
+		skb = (struct sk_buff *)(cur_p->sw_id_offset);
+
+		if (lp->eth_hasnobuf ||
+		    lp->axienet_config->mactype != XAXIENET_1G)
+			length = cur_p->status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+		else
+			length = cur_p->app4 & 0x0000FFFF;
+
+		skb_put(skb, length);
+		skb->protocol = eth_type_trans(skb, ndev);
+		/*skb_checksum_none_assert(skb);*/
+		skb->ip_summed = CHECKSUM_NONE;
+
+		/* if we're doing Rx csum offload, set it up */
+		if (lp->features & XAE_FEATURE_FULL_RX_CSUM &&
+		    lp->axienet_config->mactype == XAXIENET_1G &&
+		    !lp->eth_hasnobuf) {
+			csumstatus = (cur_p->app2 &
+				      XAE_FULL_CSUM_STATUS_MASK) >> 3;
+			if (csumstatus == XAE_IP_TCP_CSUM_VALIDATED ||
+			    csumstatus == XAE_IP_UDP_CSUM_VALIDATED) {
+				skb->ip_summed = CHECKSUM_UNNECESSARY;
+			}
+		} else if ((lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) != 0 &&
+			   skb->protocol == htons(ETH_P_IP) &&
+			   skb->len > 64 && !lp->eth_hasnobuf &&
+			   (lp->axienet_config->mactype == XAXIENET_1G)) {
+			skb->csum = be32_to_cpu(cur_p->app3 & 0xFFFF);
+			skb->ip_summed = CHECKSUM_COMPLETE;
+		}
+		if (unlikely(q->flags & MCDMA_MGMT_CHAN)) {
+			/* received packet on mgmt channel */
+			if ((sband_status & XMCDMA_BD_SD_STS_ALL_MASK)
+			    == XMCDMA_BD_SD_STS_TUSER_MAC_1) {
+				temp_ndev = lp->slaves[0];
+			} else if ((sband_status & XMCDMA_BD_SD_STS_ALL_MASK)
+				 == XMCDMA_BD_SD_STS_TUSER_MAC_2) {
+				temp_ndev = lp->slaves[1];
+			} else if ((sband_status & XMCDMA_BD_SD_STS_ALL_MASK)
+				 == XMCDMA_BD_SD_STS_TUSER_EP) {
+				temp_ndev = lp->ndev;
+			} else if (lp->ex_ep && ((sband_status &
+				XMCDMA_BD_SD_STS_ALL_MASK) ==
+				XMCDMA_BD_SD_STS_TUSER_EX_EP)) {
+				temp_ndev = lp->ex_ep;
+			}
+
+			/* send to one of the front panel port */
+			if (temp_ndev && netif_running(temp_ndev)) {
+				skb->dev = temp_ndev;
+				netif_receive_skb(skb);
+			} else {
+				kfree(skb); /* dont send up the stack */
+			}
+		} else if (unlikely(q->flags & MCDMA_EP_EX_CHAN)) {
+			temp_ndev = lp->ex_ep;
+			if (temp_ndev && netif_running(temp_ndev)) {
+				skb->dev = temp_ndev;
+				netif_receive_skb(skb);
+			} else {
+				kfree(skb); /* dont send up the stack */
+			}
+		} else {
+			netif_receive_skb(skb); /* send on normal data path */
+		}
+
+		size += length;
+		packets++;
+
+		/* Ensure that the skb is completely updated
+		 * prio to mapping the DMA
+		 */
+		wmb();
+
+		cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
+					     lp->max_frm_size,
+					   DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, cur_p->phys))) {
+			cur_p->phys = 0;
+			dev_kfree_skb(skb);
+			dev_err(lp->dev, "RX buffer map failed\n");
+			break;
+		}
+		cur_p->cntrl = lp->max_frm_size;
+		cur_p->status = 0;
+		cur_p->sw_id_offset = (phys_addr_t)new_skb;
+
+		if (++q->rx_bd_ci >= lp->rx_bd_num)
+			q->rx_bd_ci = 0;
+
+		/* Get relevat BD status value */
+		rmb();
+		cur_p = &q->rxq_bd_v[q->rx_bd_ci];
+		numbdfree++;
+	}
+
+	ndev->stats.rx_packets += packets;
+	ndev->stats.rx_bytes += size;
+	q->rx_packets += packets;
+	q->rx_bytes += size;
+
+	if (tail_p) {
+		axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id) +
+				  q->rx_offset, tail_p);
+	}
+
+	return numbdfree;
+}
+
+/**
+ * xaxienet_rx_poll_tsn - Poll routine for rx packets (NAPI)
+ * @napi:	napi structure pointer
+ * @quota:	Max number of rx packets to be processed.
+ *
+ * This is the poll routine for rx part.
+ * It will process the packets maximux quota value.
+ *
+ * Return: number of packets received
+ */
+int xaxienet_rx_poll_tsn(struct napi_struct *napi, int quota)
+{
+	struct net_device *ndev = napi->dev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int work_done = 0;
+	unsigned int status, cr;
+
+	int map = napi - lp->napi;
+
+	struct axienet_dma_q *q = lp->dq[map];
+
+	spin_lock(&q->rx_lock);
+	status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset);
+	while ((status & (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK)) &&
+	       (work_done < quota)) {
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset, status);
+		if (status & XMCDMA_IRQ_ERR_MASK) {
+			dev_err(lp->dev, "Rx error 0x%x\n\r", status);
+			break;
+		}
+		work_done += axienet_recv(lp->ndev, quota - work_done, q);
+		status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+					  q->rx_offset);
+	}
+	spin_unlock(&q->rx_lock);
+
+	if (work_done < quota) {
+		napi_complete(napi);
+		/* Enable the interrupts again */
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      XMCDMA_RX_OFFSET);
+		cr |= (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK);
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  XMCDMA_RX_OFFSET, cr);
+	}
+
+	return work_done;
+}
+
+/**
+ * axienet_change_mtu - Driver change mtu routine.
+ * @ndev:	Pointer to net_device structure
+ * @new_mtu:	New mtu value to be applied
+ *
+ * Return: Always returns 0 (success).
+ *
+ * This is the change mtu driver routine. It checks if the Axi Ethernet
+ * hardware supports jumbo frames before changing the mtu. This can be
+ * called only when the device is not up.
+ */
+static int axienet_change_mtu(struct net_device *ndev, int new_mtu)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (netif_running(ndev))
+		return -EBUSY;
+
+	if ((new_mtu + VLAN_ETH_HLEN +
+		XAE_TRL_SIZE) > lp->rxmem)
+		return -EINVAL;
+
+	ndev->mtu = new_mtu;
+
+	return 0;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/**
+ * axienet_poll_controller - Axi Ethernet poll mechanism.
+ * @ndev:	Pointer to net_device structure
+ *
+ * This implements Rx/Tx ISR poll mechanisms. The interrupts are disabled prior
+ * to polling the ISRs and are enabled back after the polling is done.
+ */
+static void axienet_poll_controller(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i;
+
+	for_each_tx_dma_queue(lp, i)
+		disable_irq(lp->dq[i]->tx_irq);
+	for_each_rx_dma_queue(lp, i)
+		disable_irq(lp->dq[i]->rx_irq);
+
+	for_each_rx_dma_queue(lp, i)
+		axienet_mcdma_rx_irq_tsn(lp->dq[i]->rx_irq, ndev);
+	for_each_tx_dma_queue(lp, i)
+		axienet_mcdma_tx_irq_tsn(lp->dq[i]->tx_irq, ndev);
+	for_each_tx_dma_queue(lp, i)
+		enable_irq(lp->dq[i]->tx_irq);
+	for_each_rx_dma_queue(lp, i)
+		enable_irq(lp->dq[i]->rx_irq);
+}
+#endif
+
+#if defined(CONFIG_XILINX_TSN_PTP)
+/**
+ *  axienet_set_timestamp_mode - sets up the hardware for the requested mode
+ *  @lp: Pointer to axienet local structure
+ *  @config: the hwtstamp configuration requested
+ *
+ * Return: 0 on success, Negative value on errors
+ */
+static int axienet_set_timestamp_mode(struct axienet_local *lp,
+				      struct hwtstamp_config *config)
+{
+	u32 regval;
+
+#ifdef CONFIG_XILINX_TSN_PTP
+	/* reserved for future extensions */
+	if (config->flags)
+		return -EINVAL;
+
+	if (config->tx_type < HWTSTAMP_TX_OFF ||
+	    config->tx_type > HWTSTAMP_TX_ONESTEP_SYNC)
+		return -ERANGE;
+
+	lp->ptp_ts_type = config->tx_type;
+
+	/* On RX always timestamp everything */
+	switch (config->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		break;
+	default:
+		config->rx_filter = lp->current_rx_filter;
+	}
+	return 0;
+
+#endif
+
+	/* reserved for future extensions */
+	if (config->flags)
+		return -EINVAL;
+
+	/* Read the current value in the MAC TX CTRL register */
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		regval = axienet_ior(lp, XAE_TC_OFFSET);
+
+	switch (config->tx_type) {
+	case HWTSTAMP_TX_OFF:
+		regval &= ~XAE_TC_INBAND1588_MASK;
+		break;
+	case HWTSTAMP_TX_ON:
+		config->tx_type = HWTSTAMP_TX_ON;
+		regval |= XAE_TC_INBAND1588_MASK;
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC)
+			axienet_iow(lp, MRMAC_CFG1588_OFFSET, 0x0);
+		break;
+	case HWTSTAMP_TX_ONESTEP_SYNC:
+		config->tx_type = HWTSTAMP_TX_ONESTEP_SYNC;
+		regval |= XAE_TC_INBAND1588_MASK;
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC)
+			axienet_iow(lp, MRMAC_CFG1588_OFFSET, MRMAC_ONE_STEP_EN);
+		break;
+	case HWTSTAMP_TX_ONESTEP_P2P:
+		if (lp->axienet_config->mactype == XAXIENET_MRMAC) {
+			config->tx_type = HWTSTAMP_TX_ONESTEP_P2P;
+			axienet_iow(lp, MRMAC_CFG1588_OFFSET, MRMAC_ONE_STEP_EN);
+		} else {
+			return -ERANGE;
+		}
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		axienet_iow(lp, XAE_TC_OFFSET, regval);
+
+	/* Read the current value in the MAC RX RCW1 register */
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		regval = axienet_ior(lp, XAE_RCW1_OFFSET);
+
+	/* On RX always timestamp everything */
+	switch (config->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		regval &= ~XAE_RCW1_INBAND1588_MASK;
+		break;
+	default:
+		config->rx_filter = HWTSTAMP_FILTER_ALL;
+		regval |= XAE_RCW1_INBAND1588_MASK;
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		axienet_iow(lp, XAE_RCW1_OFFSET, regval);
+
+	return 0;
+}
+
+static void change_filter_values_to_udp(struct axienet_local *lp)
+{
+	axienet_iow(lp, XAE_FMC_OFFSET, FILTER_SELECT);
+	/**
+	 * axienet_iow(lp, 0x70C, 0x0); values may not
+	 * be written on to the specified address if this is not given
+	 */
+	axienet_iow(lp, XAE_FF_3_OFFSET, ETHERTYPE_FILTER_IPV4);
+	axienet_iow(lp, XAE_FF_5_OFFSET, PROTO_FILTER_UDP);
+	axienet_iow(lp, XAE_FF_9_OFFSET, PTP_UDP_PORT);
+	axienet_iow(lp, XAE_FF_10_OFFSET, PTP_VERSION);
+
+	axienet_iow(lp, XAE_AF0_MASK_OFFSET, DESTMAC_FILTER_DISABLE_MASK_MSB);
+	axienet_iow(lp, XAE_AF1_MASK_OFFSET, DESTMAC_FILTER_DISABLE_MASK_LSB);
+	axienet_iow(lp, XAE_FF_5_MASK_OFFSET, PROTO_FILTER_ENABLE_MASK);
+	axienet_iow(lp, XAE_FF_9_MASK_OFFSET, PORT_NUM_FILTER_ENABLE_MASK);
+	axienet_iow(lp, XAE_FF_10_MASK_OFFSET, VERSION_FILTER_DISABLE_MASK);
+}
+
+static void change_filter_values_to_gptp(struct axienet_local *lp)
+{
+	axienet_iow(lp, XAE_FF_3_OFFSET, ETHERTYPE_FILTER_PTP);
+	axienet_iow(lp, XAE_AF0_MASK_OFFSET, DESTMAC_FILTER_ENABLE_MASK_MSB);
+	axienet_iow(lp, XAE_AF1_MASK_OFFSET, DESTMAC_FILTER_ENABLE_MASK_LSB);
+	axienet_iow(lp, XAE_FF_5_MASK_OFFSET, PROTO_FILTER_DISABLE_MASK);
+	axienet_iow(lp, XAE_FF_9_MASK_OFFSET, PORT_NUM_FILTER_ENABLE_MASK);
+	axienet_iow(lp, XAE_FF_10_MASK_OFFSET, VERSION_FILTER_DISABLE_MASK);
+}
+
+/**
+ * axienet_set_ts_config - user entry point for timestamp mode
+ * @lp: Pointer to axienet local structure
+ * @ifr: ioctl data
+ *
+ * Set hardware to the requested more. If unsupported return an error
+ * with no changes. Otherwise, store the mode for future reference
+ *
+ * Return: 0 on success, Negative value on errors
+ */
+static int axienet_set_ts_config(struct axienet_local *lp, struct ifreq *ifr)
+{
+	struct hwtstamp_config config;
+	int err;
+
+	if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+		return -EFAULT;
+	if (config.rx_filter == HWTSTAMP_FILTER_PTP_V2_L2_EVENT &&
+	    lp->current_rx_filter == HWTSTAMP_FILTER_PTP_V2_L4_EVENT) {
+		lp->current_rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
+		change_filter_values_to_gptp(lp);
+	}
+	if (config.rx_filter == HWTSTAMP_FILTER_PTP_V2_L4_EVENT &&
+	    lp->current_rx_filter == HWTSTAMP_FILTER_PTP_V2_L2_EVENT) {
+		lp->current_rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_EVENT;
+		change_filter_values_to_udp(lp);
+	}
+	err = axienet_set_timestamp_mode(lp, &config);
+	if (err)
+		return err;
+
+	/* save these settings for future reference */
+	memcpy(&lp->tstamp_config, &config, sizeof(lp->tstamp_config));
+
+	return copy_to_user(ifr->ifr_data, &config,
+			    sizeof(config)) ? -EFAULT : 0;
+}
+
+/**
+ * axienet_get_ts_config - return the current timestamp configuration
+ * to the user
+ * @lp: pointer to axienet local structure
+ * @ifr: ioctl data
+ *
+ * Return: 0 on success, Negative value on errors
+ */
+static int axienet_get_ts_config(struct axienet_local *lp, struct ifreq *ifr)
+{
+	struct hwtstamp_config *config = &lp->tstamp_config;
+
+	return copy_to_user(ifr->ifr_data, config,
+			    sizeof(*config)) ? -EFAULT : 0;
+}
+#endif
+
+/* Ioctl MII Interface */
+static int axienet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+#if defined(CONFIG_XILINX_TSN_PTP)
+	struct axienet_local *lp = netdev_priv(dev);
+#endif
+
+	if (!netif_running(dev))
+		return -EINVAL;
+
+	switch (cmd) {
+	case SIOCGMIIPHY:
+	case SIOCGMIIREG:
+	case SIOCSMIIREG:
+		if (!dev->phydev)
+			return -EOPNOTSUPP;
+		return phy_mii_ioctl(dev->phydev, rq, cmd);
+#if defined(CONFIG_XILINX_TSN_PTP)
+	case SIOCSHWTSTAMP:
+		return axienet_set_ts_config(lp, rq);
+	case SIOCGHWTSTAMP:
+		return axienet_get_ts_config(lp, rq);
+#endif
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int axienet_ioctl_siocdevprivate(struct net_device *dev,
+					struct ifreq *rq, void __user *data, int cmd)
+{
+	struct axienet_local *lp = netdev_priv(dev);
+
+	switch (cmd) {
+#ifdef CONFIG_XILINX_TSN_QBV
+	case SIOCCHIOCTL:
+		if (lp->qbv_regs)
+			return axienet_set_schedule(dev, data);
+		return -EINVAL;
+	case SIOC_GET_SCHED:
+		if (lp->qbv_regs)
+			return axienet_get_schedule(dev, data);
+		return -EINVAL;
+#endif
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	case SIOC_TADMA_OFF:
+		if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY))
+			return -ENOENT;
+		return axienet_tadma_off(dev, data);
+	case SIOC_TADMA_STR_ADD:
+		if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY))
+			return -ENOENT;
+		return axienet_tadma_add_stream(dev, data);
+	case SIOC_TADMA_PROG_ALL:
+		if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY))
+			return -ENOENT;
+		return axienet_tadma_program(dev, data);
+	case SIOC_TADMA_STR_FLUSH:
+		if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY))
+			return -ENOENT;
+		return axienet_tadma_flush_stream(dev, data);
+#endif
+#ifdef CONFIG_XILINX_TSN_QBR
+	case SIOC_PREEMPTION_CFG:
+		return axienet_preemption(dev, data);
+	case SIOC_PREEMPTION_CTRL:
+		return axienet_preemption_ctrl(dev, data);
+	case SIOC_PREEMPTION_STS:
+		return axienet_preemption_sts(dev, data);
+	case SIOC_PREEMPTION_RECEIVE:
+		return axienet_preemption_receive(dev);
+	case SIOC_PREEMPTION_COUNTER:
+		return axienet_preemption_cnt(dev, data);
+#ifdef CONFIG_XILINX_TSN_QBV
+	case SIOC_QBU_USER_OVERRIDE:
+		return axienet_qbu_user_override(dev, data);
+	case SIOC_QBU_STS:
+		return axienet_qbu_sts(dev, data);
+#endif
+#endif
+
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static const struct net_device_ops axienet_netdev_ops = {
+	.ndo_open = axienet_tsn_open,
+	.ndo_stop = axienet_tsn_stop,
+	.ndo_start_xmit = axienet_tsn_xmit,
+	.ndo_change_mtu	= axienet_change_mtu,
+	.ndo_set_mac_address = netdev_set_mac_address,
+	.ndo_validate_addr = eth_validate_addr,
+	.ndo_eth_ioctl = axienet_ioctl,
+	.ndo_siocdevprivate = axienet_ioctl_siocdevprivate,
+	.ndo_set_rx_mode = axienet_set_multicast_list_tsn,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	.ndo_poll_controller = axienet_poll_controller,
+#endif
+#ifdef CONFIG_XILINX_TSN
+	.ndo_select_queue = axienet_tsn_select_queue,
+#if defined(CONFIG_XILINX_TSN_SWITCH)
+	.ndo_get_port_parent_id = tsn_switch_get_port_parent_id,
+#endif
+#endif
+};
+
+/**
+ * axienet_ethtools_get_drvinfo - Get various Axi Ethernet driver information.
+ * @ndev:	Pointer to net_device structure
+ * @ed:		Pointer to ethtool_drvinfo structure
+ *
+ * This implements ethtool command for getting the driver information.
+ * Issue "ethtool -i ethX" under linux prompt to execute this function.
+ */
+static void axienet_ethtools_get_drvinfo(struct net_device *ndev,
+					 struct ethtool_drvinfo *ed)
+{
+	strscpy(ed->driver, DRIVER_NAME, sizeof(ed->driver));
+	strscpy(ed->version, DRIVER_VERSION, sizeof(ed->version));
+}
+
+/**
+ * axienet_ethtools_get_regs_len - Get the total regs length present in the
+ *				   AxiEthernet core.
+ * @ndev:	Pointer to net_device structure
+ *
+ * This implements ethtool command for getting the total register length
+ * information.
+ *
+ * Return: the total regs length
+ */
+static int axienet_ethtools_get_regs_len(struct net_device *ndev)
+{
+	return sizeof(u32) * AXIENET_REGS_N;
+}
+
+/**
+ * axienet_ethtools_get_regs - Dump the contents of all registers present
+ *			       in AxiEthernet core.
+ * @ndev:	Pointer to net_device structure
+ * @regs:	Pointer to ethtool_regs structure
+ * @ret:	Void pointer used to return the contents of the registers.
+ *
+ * This implements ethtool command for getting the Axi Ethernet register dump.
+ * Issue "ethtool -d ethX" to execute this function.
+ */
+static void axienet_ethtools_get_regs(struct net_device *ndev,
+				      struct ethtool_regs *regs, void *ret)
+{
+	u32 *data = (u32 *)ret;
+	size_t len = sizeof(u32) * AXIENET_REGS_N;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	regs->version = 0;
+	regs->len = len;
+
+	memset(data, 0, len);
+	data[13] = axienet_ior(lp, XAE_RCW0_OFFSET);
+	data[14] = axienet_ior(lp, XAE_RCW1_OFFSET);
+	data[15] = axienet_ior(lp, XAE_TC_OFFSET);
+	data[16] = axienet_ior(lp, XAE_FCC_OFFSET);
+	data[17] = axienet_ior(lp, XAE_EMMC_OFFSET);
+	data[18] = axienet_ior(lp, XAE_RMFC_OFFSET);
+	data[19] = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
+	data[20] = axienet_ior(lp, XAE_MDIO_MCR_OFFSET);
+	data[21] = axienet_ior(lp, XAE_MDIO_MWD_OFFSET);
+	data[22] = axienet_ior(lp, XAE_MDIO_MRD_OFFSET);
+	data[23] = axienet_ior(lp, XAE_TEMAC_IS_OFFSET);
+	data[24] = axienet_ior(lp, XAE_TEMAC_IP_OFFSET);
+	data[25] = axienet_ior(lp, XAE_TEMAC_IE_OFFSET);
+	data[26] = axienet_ior(lp, XAE_TEMAC_IC_OFFSET);
+	data[27] = axienet_ior(lp, XAE_UAW0_OFFSET);
+	data[28] = axienet_ior(lp, XAE_UAW1_OFFSET);
+	data[29] = axienet_ior(lp, XAE_FMC_OFFSET);
+	data[30] = axienet_ior(lp, XAE_AF0_OFFSET);
+	data[31] = axienet_ior(lp, XAE_AF1_OFFSET);
+	/* Support only single DMA queue */
+	data[32] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_CR_OFFSET);
+	data[33] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_SR_OFFSET);
+	data[34] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_CDESC_OFFSET);
+	data[35] = axienet_dma_in32(lp->dq[0], XAXIDMA_TX_TDESC_OFFSET);
+	data[36] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_CR_OFFSET);
+	data[37] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_SR_OFFSET);
+	data[38] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_CDESC_OFFSET);
+	data[39] = axienet_dma_in32(lp->dq[0], XAXIDMA_RX_TDESC_OFFSET);
+}
+
+static void axienet_ethtools_get_ringparam(struct net_device *ndev,
+					   struct ethtool_ringparam *ering)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	ering->rx_max_pending = RX_BD_NUM_MAX;
+	ering->rx_mini_max_pending = 0;
+	ering->rx_jumbo_max_pending = 0;
+	ering->tx_max_pending = TX_BD_NUM_MAX;
+	ering->rx_pending = lp->rx_bd_num;
+	ering->rx_mini_pending = 0;
+	ering->rx_jumbo_pending = 0;
+	ering->tx_pending = lp->tx_bd_num;
+}
+
+static int axienet_ethtools_set_ringparam(struct net_device *ndev,
+					  struct ethtool_ringparam *ering)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (ering->rx_pending > RX_BD_NUM_MAX ||
+	    ering->rx_mini_pending ||
+	    ering->rx_jumbo_pending ||
+	    ering->rx_pending > TX_BD_NUM_MAX)
+		return -EINVAL;
+
+	if (netif_running(ndev))
+		return -EBUSY;
+
+	lp->rx_bd_num = ering->rx_pending;
+	lp->tx_bd_num = ering->tx_pending;
+	return 0;
+}
+
+/**
+ * axienet_ethtools_get_pauseparam - Get the pause parameter setting for
+ *				     Tx and Rx paths.
+ * @ndev:	Pointer to net_device structure
+ * @epauseparm:	Pointer to ethtool_pauseparam structure.
+ *
+ * This implements ethtool command for getting axi ethernet pause frame
+ * setting. Issue "ethtool -a ethX" to execute this function.
+ */
+static void
+axienet_ethtools_get_pauseparam(struct net_device *ndev,
+				struct ethtool_pauseparam *epauseparm)
+{
+	u32 regval;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	epauseparm->autoneg  = 0;
+	regval = axienet_ior(lp, XAE_FCC_OFFSET);
+	epauseparm->tx_pause = regval & XAE_FCC_FCTX_MASK;
+	epauseparm->rx_pause = regval & XAE_FCC_FCRX_MASK;
+}
+
+/**
+ * axienet_ethtools_set_pauseparam - Set device pause parameter(flow control)
+ *				     settings.
+ * @ndev:	Pointer to net_device structure
+ * @epauseparm:	Pointer to ethtool_pauseparam structure
+ *
+ * This implements ethtool command for enabling flow control on Rx and Tx
+ * paths. Issue "ethtool -A ethX tx on|off" under linux prompt to execute this
+ * function.
+ *
+ * Return: 0 on success, -EFAULT if device is running
+ */
+static int
+axienet_ethtools_set_pauseparam(struct net_device *ndev,
+				struct ethtool_pauseparam *epauseparm)
+{
+	u32 regval = 0;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (netif_running(ndev)) {
+		netdev_err(ndev,
+			   "Please stop netif before applying configuration\n");
+		return -EFAULT;
+	}
+
+	regval = axienet_ior(lp, XAE_FCC_OFFSET);
+	if (epauseparm->tx_pause)
+		regval |= XAE_FCC_FCTX_MASK;
+	else
+		regval &= ~XAE_FCC_FCTX_MASK;
+	if (epauseparm->rx_pause)
+		regval |= XAE_FCC_FCRX_MASK;
+	else
+		regval &= ~XAE_FCC_FCRX_MASK;
+	axienet_iow(lp, XAE_FCC_OFFSET, regval);
+
+	return 0;
+}
+
+/**
+ * axienet_ethtools_get_coalesce - Get DMA interrupt coalescing count.
+ * @ndev:	Pointer to net_device structure
+ * @ecoalesce:	Pointer to ethtool_coalesce structure
+ * @kernel_coal: ethtool CQE mode setting structure
+ * @extack:	extack for reporting error messages
+ *
+ * This implements ethtool command for getting the DMA interrupt coalescing
+ * count on Tx and Rx paths. Issue "ethtool -c ethX" under linux prompt to
+ * execute this function.
+ *
+ * Return: 0 always
+ */
+int axienet_ethtools_get_coalesce(struct net_device *ndev,
+				  struct ethtool_coalesce *ecoalesce,
+				  struct kernel_ethtool_coalesce *kernel_coal,
+				  struct netlink_ext_ack *extack)
+{
+	u32 regval = 0;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	int i;
+
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		if (!q)
+			return 0;
+
+		regval = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		ecoalesce->rx_max_coalesced_frames +=
+						(regval & XAXIDMA_COALESCE_MASK)
+						     >> XAXIDMA_COALESCE_SHIFT;
+	}
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		if (!q)
+			return 0;
+		regval = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+		ecoalesce->tx_max_coalesced_frames +=
+						(regval & XAXIDMA_COALESCE_MASK)
+						     >> XAXIDMA_COALESCE_SHIFT;
+	}
+	return 0;
+}
+
+/**
+ * axienet_ethtools_set_coalesce - Set DMA interrupt coalescing count.
+ * @ndev:	Pointer to net_device structure
+ * @ecoalesce:	Pointer to ethtool_coalesce structure
+ * @kernel_coal: ethtool CQE mode setting structure
+ * @extack:	extack for reporting error messages
+ *
+ * This implements ethtool command for setting the DMA interrupt coalescing
+ * count on Tx and Rx paths. Issue "ethtool -C ethX rx-frames 5" under linux
+ * prompt to execute this function.
+ *
+ * Return: 0, on success, Non-zero error value on failure.
+ */
+int axienet_ethtools_set_coalesce(struct net_device *ndev,
+				  struct ethtool_coalesce *ecoalesce,
+				  struct kernel_ethtool_coalesce *kernel_coal,
+				  struct netlink_ext_ack *extack)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (netif_running(ndev)) {
+		netdev_err(ndev,
+			   "Please stop netif before applying configuration\n");
+		return -EFAULT;
+	}
+
+	if (ecoalesce->rx_coalesce_usecs ||
+	    ecoalesce->rx_coalesce_usecs_irq ||
+	    ecoalesce->rx_max_coalesced_frames_irq ||
+	    ecoalesce->tx_coalesce_usecs ||
+	    ecoalesce->tx_coalesce_usecs_irq ||
+	    ecoalesce->tx_max_coalesced_frames_irq ||
+	    ecoalesce->stats_block_coalesce_usecs ||
+	    ecoalesce->use_adaptive_rx_coalesce ||
+	    ecoalesce->use_adaptive_tx_coalesce ||
+	    ecoalesce->pkt_rate_low ||
+	    ecoalesce->rx_coalesce_usecs_low ||
+	    ecoalesce->rx_max_coalesced_frames_low ||
+	    ecoalesce->tx_coalesce_usecs_low ||
+	    ecoalesce->tx_max_coalesced_frames_low ||
+	    ecoalesce->pkt_rate_high ||
+	    ecoalesce->rx_coalesce_usecs_high ||
+	    ecoalesce->rx_max_coalesced_frames_high ||
+	    ecoalesce->tx_coalesce_usecs_high ||
+	    ecoalesce->tx_max_coalesced_frames_high ||
+	    ecoalesce->rate_sample_interval)
+		return -EOPNOTSUPP;
+	if (ecoalesce->rx_max_coalesced_frames)
+		lp->coalesce_count_rx = ecoalesce->rx_max_coalesced_frames;
+	if (ecoalesce->tx_max_coalesced_frames)
+		lp->coalesce_count_tx = ecoalesce->tx_max_coalesced_frames;
+
+	return 0;
+}
+
+#if defined(CONFIG_XILINX_TSN_PTP)
+/**
+ * axienet_ethtools_get_ts_info - Get h/w timestamping capabilities.
+ * @ndev:	Pointer to net_device structure
+ * @info:	Pointer to ethtool_ts_info structure
+ *
+ * Return: 0, on success, Non-zero error value on failure.
+ */
+static int axienet_ethtools_get_ts_info(struct net_device *ndev,
+					struct ethtool_ts_info *info)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE |
+				SOF_TIMESTAMPING_RX_HARDWARE |
+				SOF_TIMESTAMPING_RAW_HARDWARE;
+	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON) |
+			(1 << HWTSTAMP_TX_ONESTEP_SYNC) |
+			(1 << HWTSTAMP_TX_ONESTEP_P2P);
+	info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) |
+			   (1 << HWTSTAMP_FILTER_ALL);
+	info->phc_index = lp->phc_index;
+
+#ifdef CONFIG_XILINX_TSN_PTP
+	info->phc_index = axienet_phc_index;
+#endif
+	return 0;
+}
+#endif
+
+/**
+ * axienet_ethtools_sset_count - Get number of strings that
+ *				 get_strings will write.
+ * @ndev:	Pointer to net_device structure
+ * @sset:	Get the set strings
+ *
+ * Return: number of strings, on success, Non-zero error value on
+ *	   failure.
+ */
+static int axienet_ethtools_sset_count(struct net_device *ndev, int sset)
+{
+	switch (sset) {
+	case ETH_SS_STATS:
+		return axienet_sset_count_tsn(ndev, sset);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+/**
+ * axienet_ethtools_get_stats - Get the extended statistics
+ *				about the device.
+ * @ndev:	Pointer to net_device structure
+ * @stats:	Pointer to ethtool_stats structure
+ * @data:	To store the statistics values
+ *
+ * Return: None.
+ */
+static void axienet_ethtools_get_stats(struct net_device *ndev,
+				       struct ethtool_stats *stats,
+				       u64 *data)
+{
+	unsigned int i = 0;
+
+	data[i++] = ndev->stats.tx_packets;
+	data[i++] = ndev->stats.rx_packets;
+	data[i++] = ndev->stats.tx_bytes;
+	data[i++] = ndev->stats.rx_bytes;
+	data[i++] = ndev->stats.tx_errors;
+	data[i++] = ndev->stats.rx_missed_errors + ndev->stats.rx_frame_errors;
+
+	axienet_get_stats_tsn(ndev, stats, data);
+}
+
+/**
+ * axienet_ethtools_strings - Set of strings that describe
+ *			 the requested objects.
+ * @ndev:	Pointer to net_device structure
+ * @sset:	Get the set strings
+ * @data:	Data of Transmit and Receive statistics
+ *
+ * Return: None.
+ */
+static void axienet_ethtools_strings(struct net_device *ndev, u32 sset, u8 *data)
+{
+	int i;
+
+	for (i = 0; i < AXIENET_ETHTOOLS_SSTATS_LEN; i++) {
+		if (sset == ETH_SS_STATS)
+			memcpy(data + i * ETH_GSTRING_LEN,
+			       axienet_get_ethtools_strings_stats[i].name,
+			       ETH_GSTRING_LEN);
+	}
+	axienet_strings_tsn(ndev, sset, data);
+}
+
+static const struct ethtool_ops axienet_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_MAX_FRAMES,
+	.get_drvinfo    = axienet_ethtools_get_drvinfo,
+	.get_regs_len   = axienet_ethtools_get_regs_len,
+	.get_regs       = axienet_ethtools_get_regs,
+	.get_link       = ethtool_op_get_link,
+	.get_ringparam	= axienet_ethtools_get_ringparam,
+	.set_ringparam  = axienet_ethtools_set_ringparam,
+	.get_pauseparam = axienet_ethtools_get_pauseparam,
+	.set_pauseparam = axienet_ethtools_set_pauseparam,
+	.get_coalesce   = axienet_ethtools_get_coalesce,
+	.set_coalesce   = axienet_ethtools_set_coalesce,
+	.get_sset_count	= axienet_ethtools_sset_count,
+	.get_ethtool_stats = axienet_ethtools_get_stats,
+	.get_strings = axienet_ethtools_strings,
+#if defined(CONFIG_XILINX_TSN_PTP)
+	.get_ts_info    = axienet_ethtools_get_ts_info,
+#endif
+	.get_link_ksettings = phy_ethtool_get_link_ksettings,
+	.set_link_ksettings = phy_ethtool_set_link_ksettings,
+#if defined(CONFIG_XILINX_TSN_QBR)
+	.get_mm		= axienet_preemption_sts_ethtool,
+	.set_mm		= axienet_preemption_ctrl_ethtool,
+	.get_mm_stats	= axienet_preemption_cnt_ethtool,
+#endif
+};
+
+static int axienet_clk_init(struct platform_device *pdev,
+			    struct clk **axi_aclk, struct clk **axis_clk,
+			    struct clk **ref_clk, struct clk **tmpclk)
+{
+	int err;
+
+	*tmpclk = NULL;
+
+	/* The "ethernet_clk" is deprecated and will be removed sometime in
+	 * the future. For proper clock usage check axiethernet binding
+	 * documentation.
+	 */
+	*axi_aclk = devm_clk_get(&pdev->dev, "ethernet_clk");
+	if (IS_ERR(*axi_aclk)) {
+		if (PTR_ERR(*axi_aclk) != -ENOENT) {
+			err = PTR_ERR(*axi_aclk);
+			return err;
+		}
+
+		*axi_aclk = devm_clk_get(&pdev->dev, "s_axi_lite_clk");
+		if (IS_ERR(*axi_aclk)) {
+			if (PTR_ERR(*axi_aclk) != -ENOENT) {
+				err = PTR_ERR(*axi_aclk);
+				return err;
+			}
+			*axi_aclk = NULL;
+		}
+
+	} else {
+		dev_warn(&pdev->dev, "ethernet_clk is deprecated and will be removed sometime in the future\n");
+	}
+
+	*axis_clk = devm_clk_get(&pdev->dev, "axis_clk");
+	if (IS_ERR(*axis_clk)) {
+		if (PTR_ERR(*axis_clk) != -ENOENT) {
+			err = PTR_ERR(*axis_clk);
+			return err;
+		}
+		*axis_clk = NULL;
+	}
+
+	*ref_clk = devm_clk_get(&pdev->dev, "ref_clk");
+	if (IS_ERR(*ref_clk)) {
+		if (PTR_ERR(*ref_clk) != -ENOENT) {
+			err = PTR_ERR(*ref_clk);
+			return err;
+		}
+		*ref_clk = NULL;
+	}
+
+	err = clk_prepare_enable(*axi_aclk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable axi_aclk/ethernet_clk (%d)\n", err);
+		return err;
+	}
+
+	err = clk_prepare_enable(*axis_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable axis_clk (%d)\n", err);
+		goto err_disable_axi_aclk;
+	}
+
+	err = clk_prepare_enable(*ref_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable ref_clk (%d)\n", err);
+		goto err_disable_axis_clk;
+	}
+
+	return 0;
+
+err_disable_axis_clk:
+	clk_disable_unprepare(*axis_clk);
+err_disable_axi_aclk:
+	clk_disable_unprepare(*axi_aclk);
+
+	return err;
+}
+
+static void axienet_clk_disable(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	clk_disable_unprepare(lp->dma_sg_clk);
+	clk_disable_unprepare(lp->dma_tx_clk);
+	clk_disable_unprepare(lp->dma_rx_clk);
+	clk_disable_unprepare(lp->eth_sclk);
+	clk_disable_unprepare(lp->eth_refclk);
+	clk_disable_unprepare(lp->eth_dclk);
+	clk_disable_unprepare(lp->aclk);
+}
+
+static const struct axienet_config axienet_1g_config_tsn = {
+	.mactype = XAXIENET_1G,
+	.setoptions = axienet_setoptions_tsn,
+	.clk_init = axienet_clk_init,
+	.tx_ptplen = XAE_TX_PTP_LEN,
+};
+
+/* Match table for of_platform binding */
+static const struct of_device_id axienet_of_match[] = {
+	{ .compatible = "xlnx,tsn-ethernet-1.00.a", .data = &axienet_1g_config_tsn},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, axienet_of_match);
+
+/**
+ * axienet_probe - Axi Ethernet probe function.
+ * @pdev:	Pointer to platform device structure.
+ *
+ * Return: 0, on success
+ *	    Non-zero error value on failure.
+ *
+ * This is the probe routine for Axi Ethernet driver. This is called before
+ * any other driver routines are invoked. It allocates and sets up the Ethernet
+ * device. Parses through device tree and populates fields of
+ * axienet_local. It registers the Ethernet device.
+ */
+static int axienet_probe(struct platform_device *pdev)
+{
+	int (*axienet_clk_init)(struct platform_device *pdev,
+				struct clk **axi_aclk, struct clk **axis_clk,
+				struct clk **ref_clk, struct clk **tmpclk) =
+					axienet_clk_init;
+	int ret = 0;
+	struct axienet_local *lp;
+	struct net_device *ndev;
+	u8 mac_addr[ETH_ALEN];
+	struct resource *ethres;
+	u32 value;
+	u16 num_queues = XAE_MAX_QUEUES;
+
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-queues",
+				   &num_queues);
+	if (num_queues < XAE_TSN_MIN_QUEUES)
+		num_queues = XAE_TSN_MIN_QUEUES;
+	else if (num_queues > XAE_MAX_QUEUES)
+		num_queues = XAE_MAX_QUEUES;
+
+	ndev = alloc_etherdev_mq(sizeof(*lp), num_queues);
+	if (!ndev)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ndev);
+
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+	ndev->flags &= ~IFF_MULTICAST;  /* clear multicast */
+	ndev->features = NETIF_F_SG;
+	ndev->netdev_ops = &axienet_netdev_ops;
+	ndev->ethtool_ops = &axienet_ethtool_ops;
+
+	/* MTU range: 64 - 9000 */
+	ndev->min_mtu = 64;
+	ndev->max_mtu = XAE_JUMBO_MTU;
+
+	lp = netdev_priv(ndev);
+	lp->ndev = ndev;
+	lp->dev = &pdev->dev;
+	lp->options = XAE_OPTION_DEFAULTS;
+	lp->num_tx_queues = num_queues;
+	lp->num_rx_queues = num_queues;
+	lp->rx_bd_num = RX_BD_NUM_DEFAULT;
+	lp->tx_bd_num = TX_BD_NUM_DEFAULT;
+
+	lp->axi_clk = devm_clk_get_optional(&pdev->dev, "s_axi_lite_clk");
+	if (!lp->axi_clk) {
+		/* For backward compatibility, if named AXI clock is not present,
+		 * treat the first clock specified as the AXI clock.
+		 */
+		lp->axi_clk = devm_clk_get_optional(&pdev->dev, NULL);
+	}
+	if (IS_ERR(lp->axi_clk)) {
+		ret = PTR_ERR(lp->axi_clk);
+		goto free_netdev;
+	}
+	ret = clk_prepare_enable(lp->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable AXI clock: %d\n", ret);
+		goto free_netdev;
+	}
+
+	lp->misc_clks[0].id = "axis_clk";
+	lp->misc_clks[1].id = "ref_clk";
+	lp->misc_clks[2].id = "mgt_clk";
+
+	ret = devm_clk_bulk_get_optional(&pdev->dev, XAE_NUM_MISC_CLOCKS, lp->misc_clks);
+	if (ret)
+		goto cleanup_clk;
+
+	ret = clk_bulk_prepare_enable(XAE_NUM_MISC_CLOCKS, lp->misc_clks);
+	if (ret)
+		goto cleanup_clk;
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-tc",
+				   &lp->num_tc);
+	if (ret || (lp->num_tc != 2 && lp->num_tc != 3))
+		lp->num_tc = XAE_MAX_TSN_TC;
+
+	/* Map device registers */
+	lp->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &ethres);
+	if (IS_ERR(lp->regs)) {
+		ret = PTR_ERR(lp->regs);
+		goto cleanup_clk;
+	}
+	lp->regs_start = ethres->start;
+
+	/* Setup checksum offload, but default to off if not specified */
+	lp->features = 0;
+
+	if (pdev->dev.of_node) {
+		const struct of_device_id *match;
+
+		match = of_match_node(axienet_of_match, pdev->dev.of_node);
+		if (match && match->data) {
+			lp->axienet_config = match->data;
+			axienet_clk_init = lp->axienet_config->clk_init;
+		}
+	}
+
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,txcsum", &value);
+	if (!ret) {
+		dev_info(&pdev->dev, "TX_CSUM %d\n", value);
+
+		switch (value) {
+		case 1:
+			lp->csum_offload_on_tx_path =
+				XAE_FEATURE_PARTIAL_TX_CSUM;
+			lp->features |= XAE_FEATURE_PARTIAL_TX_CSUM;
+			/* Can checksum TCP/UDP over IPv4. */
+			ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
+			break;
+		case 2:
+			lp->csum_offload_on_tx_path =
+				XAE_FEATURE_FULL_TX_CSUM;
+			lp->features |= XAE_FEATURE_FULL_TX_CSUM;
+			/* Can checksum TCP/UDP over IPv4. */
+			ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
+			break;
+		default:
+			lp->csum_offload_on_tx_path = XAE_NO_CSUM_OFFLOAD;
+		}
+	}
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,rxcsum", &value);
+	if (!ret) {
+		dev_info(&pdev->dev, "RX_CSUM %d\n", value);
+
+		switch (value) {
+		case 1:
+			lp->csum_offload_on_rx_path =
+				XAE_FEATURE_PARTIAL_RX_CSUM;
+			lp->features |= XAE_FEATURE_PARTIAL_RX_CSUM;
+			break;
+		case 2:
+			lp->csum_offload_on_rx_path =
+				XAE_FEATURE_FULL_RX_CSUM;
+			lp->features |= XAE_FEATURE_FULL_RX_CSUM;
+			break;
+		default:
+			lp->csum_offload_on_rx_path = XAE_NO_CSUM_OFFLOAD;
+		}
+	}
+	/* For supporting jumbo frames, the Axi Ethernet hardware must have
+	 * a larger Rx/Tx Memory. Typically, the size must be large so that
+	 * we can enable jumbo option and start supporting jumbo frames.
+	 * Here we check for memory allocated for Rx/Tx in the hardware from
+	 * the device-tree and accordingly set flags.
+	 */
+	of_property_read_u32(pdev->dev.of_node, "xlnx,rxmem", &lp->rxmem);
+
+	/* The phy_mode is optional but when it is not specified it should not
+	 *  be a value that alters the driver behavior so set it to an invalid
+	 *  value as the default.
+	 */
+	lp->phy_mode = PHY_INTERFACE_MODE_NA;
+	ret = of_property_read_u32(pdev->dev.of_node, "xlnx,phy-type", &lp->phy_mode);
+	if (!ret)
+		netdev_warn(ndev, "xlnx,phy-type is deprecated, Please upgrade your device tree to use phy-mode");
+
+	/* Set default USXGMII rate */
+	lp->usxgmii_rate = SPEED_1000;
+	of_property_read_u32(pdev->dev.of_node, "xlnx,usxgmii-rate",
+			     &lp->usxgmii_rate);
+
+	/* Set default MRMAC rate */
+	lp->mrmac_rate = SPEED_10000;
+	of_property_read_u32(pdev->dev.of_node, "xlnx,mrmac-rate",
+			     &lp->mrmac_rate);
+
+	lp->eth_hasnobuf = of_property_read_bool(pdev->dev.of_node,
+						 "xlnx,eth-hasnobuf");
+	lp->eth_hasptp = of_property_read_bool(pdev->dev.of_node,
+					       "xlnx,eth-hasptp");
+
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf)
+		lp->eth_irq = platform_get_irq(pdev, 0);
+
+	ret = axienet_tsn_probe(pdev, lp, ndev);
+
+	if (ret)
+		goto cleanup_clk;
+
+	ret = axienet_clk_init(pdev, &lp->aclk, &lp->eth_sclk,
+			       &lp->eth_refclk, &lp->eth_dclk);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Ethernet clock init failed %d\n", ret);
+		goto err_disable_clk;
+	}
+
+	lp->eth_irq = platform_get_irq(pdev, 0);
+	/* Check for Ethernet core IRQ (optional) */
+	if (lp->eth_irq <= 0)
+		dev_info(&pdev->dev, "Ethernet core IRQ not defined\n");
+
+	/* Retrieve the MAC address */
+	ret = of_get_mac_address(pdev->dev.of_node, mac_addr);
+	if (!ret) {
+		axienet_set_mac_address_tsn(ndev, mac_addr);
+	} else {
+		dev_warn(&pdev->dev, "could not find MAC address property: %d\n",
+			 ret);
+		axienet_set_mac_address_tsn(ndev, NULL);
+	}
+
+	lp->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD;
+	lp->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD;
+
+	ret = of_get_phy_mode(pdev->dev.of_node, &lp->phy_mode);
+	if (ret < 0)
+		dev_warn(&pdev->dev, "couldn't find phy i/f\n");
+	if (lp->phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+		lp->phy_flags = XAE_PHY_TYPE_1000BASE_X;
+
+	lp->phy_node = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0);
+	if (lp->phy_node) {
+		ret = axienet_mdio_setup(lp);
+		if (ret)
+			dev_warn(&pdev->dev,
+				 "error registering MDIO bus: %d\n", ret);
+	}
+
+	/* Create sysfs file entries for the device */
+	ret = axeinet_mcdma_create_sysfs_tsn(&lp->dev->kobj);
+	if (ret < 0) {
+		dev_err(lp->dev, "unable to create sysfs entries\n");
+		return ret;
+	}
+
+	ret = register_netdev(lp->ndev);
+	if (ret) {
+		dev_err(lp->dev, "register_netdev() error (%i)\n", ret);
+		axienet_mdio_teardown(lp);
+		goto cleanup_clk;
+	}
+
+	return 0;
+
+cleanup_clk:
+	clk_bulk_disable_unprepare(XAE_NUM_MISC_CLOCKS, lp->misc_clks);
+	clk_disable_unprepare(lp->axi_clk);
+
+err_disable_clk:
+	axienet_clk_disable(pdev);
+
+free_netdev:
+	free_netdev(ndev);
+
+	return ret;
+}
+
+static int axienet_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct axienet_local *lp = netdev_priv(ndev);
+
+#ifdef CONFIG_XILINX_TSN_PTP
+	if (lp->timer_priv)
+		axienet_ptp_timer_remove(lp->timer_priv);
+#ifdef CONFIG_XILINX_TSN_QBV
+		axienet_qbv_remove(ndev);
+#endif
+#endif
+	unregister_netdev(ndev);
+	axienet_clk_disable(pdev);
+
+	if (lp->mii_bus)
+		axienet_mdio_teardown(lp);
+
+	clk_bulk_disable_unprepare(XAE_NUM_MISC_CLOCKS, lp->misc_clks);
+	clk_disable_unprepare(lp->axi_clk);
+
+	axeinet_mcdma_remove_sysfs_tsn(&lp->dev->kobj);
+	of_node_put(lp->phy_node);
+	lp->phy_node = NULL;
+
+	free_netdev(ndev);
+
+	return 0;
+}
+
+static void axienet_shutdown(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+
+	rtnl_lock();
+	netif_device_detach(ndev);
+
+	if (netif_running(ndev))
+		dev_close(ndev);
+
+	rtnl_unlock();
+}
+
+static struct platform_driver axienet_driver_tsn = {
+	.probe = axienet_probe,
+	.remove = axienet_remove,
+	.shutdown = axienet_shutdown,
+	.driver = {
+		 .name = "xilinx_axienet_tsn",
+		 .of_match_table = axienet_of_match,
+	},
+};
+
+module_platform_driver(axienet_driver_tsn);
+
+MODULE_DESCRIPTION("Xilinx Axi Ethernet driver");
+MODULE_AUTHOR("Xilinx");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_axienet_mcdma_tsn.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_axienet_mcdma_tsn.c
@@ -0,0 +1,1118 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Xilinx AXI Ethernet (MCDMA programming)
+ *
+ * Copyright (c) 2008 Nissin Systems Co., Ltd.,  Yoshio Kashiwagi
+ * Copyright (c) 2005-2008 DLA Systems,  David H. Lynch Jr. <dhlii@dlasys.net>
+ * Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
+ * Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
+ * Copyright (c) 2010 - 2011 PetaLogix
+ * Copyright (c) 2010 - 2012 Xilinx, Inc.
+ * Copyright (C) 2018 Xilinx, Inc. All rights reserved.
+ *
+ * This file contains helper functions for AXI MCDMA TX and RX programming.
+ */
+
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/of_net.h>
+
+#include "xilinx_axienet_tsn.h"
+
+struct axienet_stat {
+	const char *name;
+};
+
+/* TODO
+ * The channel numbers for managemnet frames in 5 channel mcdma on EP+Switch
+ * system. These are not exposed via hdf/dtsi, so need to hardcode here
+ */
+#define TSN_MAX_RX_Q_EX_EPSWITCH 7
+#define TSN_MIN_RX_Q_EX_EPSWITCH 5
+#define TSN_MGMT_CHAN 3
+#define TSN_MAX_EX_EP_BE_CHAN 5
+#define TSN_MAX_EX_EP_ST_CHAN 6
+#define TSN_MAX_EX_EP_RES_CHAN 7
+#define TSN_MIN_EX_EP_BE_CHAN 4
+#define TSN_MIN_EX_EP_ST_CHAN 5
+
+static struct axienet_stat axienet_get_tx_strings_stats[] = {
+	{ "txq0_packets" },
+	{ "txq0_bytes"   },
+	{ "txq1_packets" },
+	{ "txq1_bytes"   },
+	{ "txq2_packets" },
+	{ "txq2_bytes"   },
+	{ "txq3_packets" },
+	{ "txq3_bytes"   },
+	{ "txq4_packets" },
+	{ "txq4_bytes"   },
+	{ "txq5_packets" },
+	{ "txq5_bytes"   },
+	{ "txq6_packets" },
+	{ "txq6_bytes"   },
+	{ "txq7_packets" },
+	{ "txq7_bytes"   },
+	{ "txq8_packets" },
+	{ "txq8_bytes"   },
+	{ "txq9_packets" },
+	{ "txq9_bytes"   },
+	{ "txq10_packets" },
+	{ "txq10_bytes"   },
+	{ "txq11_packets" },
+	{ "txq11_bytes"   },
+	{ "txq12_packets" },
+	{ "txq12_bytes"   },
+	{ "txq13_packets" },
+	{ "txq13_bytes"   },
+	{ "txq14_packets" },
+	{ "txq14_bytes"   },
+	{ "txq15_packets" },
+	{ "txq15_bytes"   },
+};
+
+static struct axienet_stat axienet_get_rx_strings_stats[] = {
+	{ "rxq0_packets" },
+	{ "rxq0_bytes"   },
+	{ "rxq1_packets" },
+	{ "rxq1_bytes"   },
+	{ "rxq2_packets" },
+	{ "rxq2_bytes"   },
+	{ "rxq3_packets" },
+	{ "rxq3_bytes"   },
+	{ "rxq4_packets" },
+	{ "rxq4_bytes"   },
+	{ "rxq5_packets" },
+	{ "rxq5_bytes"   },
+	{ "rxq6_packets" },
+	{ "rxq6_bytes"   },
+	{ "rxq7_packets" },
+	{ "rxq7_bytes"   },
+	{ "rxq8_packets" },
+	{ "rxq8_bytes"   },
+	{ "rxq9_packets" },
+	{ "rxq9_bytes"   },
+	{ "rxq10_packets" },
+	{ "rxq10_bytes"   },
+	{ "rxq11_packets" },
+	{ "rxq11_bytes"   },
+	{ "rxq12_packets" },
+	{ "rxq12_bytes"   },
+	{ "rxq13_packets" },
+	{ "rxq13_bytes"   },
+	{ "rxq14_packets" },
+	{ "rxq14_bytes"   },
+	{ "rxq15_packets" },
+	{ "rxq15_bytes"   },
+};
+
+/**
+ * axienet_mcdma_tx_bd_free_tsn - Release MCDMA Tx buffer descriptor rings
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * This function is used to release the descriptors allocated in
+ * axienet_mcdma_tx_q_init_tsn.
+ */
+void __maybe_unused axienet_mcdma_tx_bd_free_tsn(struct net_device *ndev,
+						 struct axienet_dma_q *q)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (q->txq_bd_v) {
+		dma_free_coherent(ndev->dev.parent,
+				  sizeof(*q->txq_bd_v) * lp->tx_bd_num,
+				  q->txq_bd_v,
+				  q->tx_bd_p);
+	}
+	if (q->tx_bufs) {
+		dma_free_coherent(ndev->dev.parent,
+				  XAE_MAX_PKT_LEN * lp->tx_bd_num,
+				  q->tx_bufs,
+				  q->tx_bufs_dma);
+	}
+}
+
+/**
+ * axienet_mcdma_rx_bd_free_tsn - Release MCDMA Rx buffer descriptor rings
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * This function is used to release the descriptors allocated in
+ * axienet_mcdma_rx_q_init_tsn.
+ */
+void __maybe_unused axienet_mcdma_rx_bd_free_tsn(struct net_device *ndev,
+						 struct axienet_dma_q *q)
+{
+	int i;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	if (!q->rxq_bd_v)
+		return;
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		if (q->rxq_bd_v[i].phys)
+			dma_unmap_single(ndev->dev.parent, q->rxq_bd_v[i].phys,
+					 lp->max_frm_size, DMA_FROM_DEVICE);
+		dev_kfree_skb((struct sk_buff *)
+			      (q->rxq_bd_v[i].sw_id_offset));
+	}
+
+	dma_free_coherent(ndev->dev.parent,
+			  sizeof(*q->rxq_bd_v) * lp->rx_bd_num,
+			  q->rxq_bd_v,
+			  q->rx_bd_p);
+	q->rxq_bd_v = NULL;
+}
+
+/**
+ * axienet_mcdma_tx_q_init_tsn - Setup buffer descriptor rings for individual Axi
+ * MCDMA-Tx
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_bd_init
+ */
+int __maybe_unused axienet_mcdma_tx_q_init_tsn(struct net_device *ndev,
+					       struct axienet_dma_q *q)
+{
+	u32 cr, chan_en;
+	int i;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	q->tx_bd_ci = 0;
+	q->tx_bd_tail = 0;
+
+	q->txq_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					 sizeof(*q->txq_bd_v) * lp->tx_bd_num,
+					 &q->tx_bd_p, GFP_KERNEL);
+	if (!q->txq_bd_v)
+		goto out;
+
+	if (!q->eth_hasdre) {
+		q->tx_bufs = dma_alloc_coherent(ndev->dev.parent,
+						XAE_MAX_PKT_LEN * lp->tx_bd_num,
+						&q->tx_bufs_dma,
+						GFP_KERNEL);
+		if (!q->tx_bufs)
+			goto out;
+
+		for (i = 0; i < lp->tx_bd_num; i++)
+			q->tx_buf[i] = &q->tx_bufs[i * XAE_MAX_PKT_LEN];
+	}
+
+	for (i = 0; i < lp->tx_bd_num; i++) {
+		q->txq_bd_v[i].next = q->tx_bd_p +
+				      sizeof(*q->txq_bd_v) *
+				      ((i + 1) % lp->tx_bd_num);
+	}
+
+	/* Start updating the Tx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	/* Update the interrupt coalesce count */
+	cr = (((cr & ~XMCDMA_COALESCE_MASK)) |
+	      ((lp->coalesce_count_tx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = (((cr & ~XMCDMA_DELAY_MASK)) |
+	      (XAXIDMA_DFT_TX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Tx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+	/* Write to the RS (Run-stop) bit in the Tx channel control register.
+	 * Tx channel is now ready to run. But only after we write to the
+	 * tail pointer register that the Tx channel will start transmitting.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id),
+			  q->tx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id),
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET, chan_en);
+
+	return 0;
+out:
+	for_each_tx_dma_queue(lp, i) {
+		axienet_mcdma_tx_bd_free_tsn(ndev, lp->dq[i]);
+	}
+	return -ENOMEM;
+}
+
+/**
+ * axienet_mcdma_rx_q_init_tsn - Setup buffer descriptor rings for individual Axi
+ * MCDMA-Rx
+ * @ndev:	Pointer to the net_device structure
+ * @q:		Pointer to DMA queue structure
+ *
+ * Return: 0, on success -ENOMEM, on failure
+ *
+ * This function is helper function to axienet_dma_bd_init
+ */
+int __maybe_unused axienet_mcdma_rx_q_init_tsn(struct net_device *ndev,
+					       struct axienet_dma_q *q)
+{
+	u32 cr, chan_en;
+	int i;
+	struct sk_buff *skb;
+	struct axienet_local *lp = netdev_priv(ndev);
+	dma_addr_t mapping;
+
+	q->rx_bd_ci = 0;
+	q->rx_offset = XMCDMA_CHAN_RX_OFFSET;
+
+	q->rxq_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					 sizeof(*q->rxq_bd_v) * lp->rx_bd_num,
+					 &q->rx_bd_p, GFP_KERNEL);
+	if (!q->rxq_bd_v)
+		goto out;
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		q->rxq_bd_v[i].next = q->rx_bd_p +
+				      sizeof(*q->rxq_bd_v) *
+				      ((i + 1) % lp->rx_bd_num);
+
+		skb = netdev_alloc_skb(ndev, lp->max_frm_size);
+		if (!skb)
+			goto out;
+
+		/* Ensure that the skb is completely updated
+		 * prio to mapping the DMA
+		 */
+		wmb();
+
+		q->rxq_bd_v[i].sw_id_offset = (phys_addr_t)skb;
+		mapping = dma_map_single(ndev->dev.parent,
+					 skb->data,
+					 lp->max_frm_size,
+					 DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(ndev->dev.parent, mapping))) {
+			dev_err(&ndev->dev, "mcdma map error\n");
+			goto out;
+		}
+
+		q->rxq_bd_v[i].phys = mapping;
+		q->rxq_bd_v[i].cntrl = lp->max_frm_size;
+	}
+
+	/* check if this is a mgmt channel */
+	if (lp->num_rx_queues == TSN_MAX_RX_Q_EX_EPSWITCH &&
+	    (q->chan_id == TSN_MAX_EX_EP_BE_CHAN ||
+	     q->chan_id == TSN_MAX_EX_EP_ST_CHAN ||
+	     q->chan_id == TSN_MAX_EX_EP_RES_CHAN)) {
+		q->flags = MCDMA_EP_EX_CHAN;
+	} else if ((lp->num_rx_queues == TSN_MIN_RX_Q_EX_EPSWITCH) &&
+		   ((q->chan_id == TSN_MIN_EX_EP_BE_CHAN) ||
+		    (q->chan_id == TSN_MIN_EX_EP_ST_CHAN))) {
+		q->flags = MCDMA_EP_EX_CHAN;
+	} else if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY) && q->chan_id == TSN_MGMT_CHAN) {
+		q->flags = MCDMA_MGMT_CHAN;
+	}
+
+	/* Start updating the Rx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			      q->rx_offset);
+	/* Update the interrupt coalesce count */
+	cr = ((cr & ~XMCDMA_COALESCE_MASK) |
+	      ((lp->coalesce_count_rx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = ((cr & ~XMCDMA_DELAY_MASK) |
+	      (XAXIDMA_DFT_RX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Rx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			  q->rx_offset, cr);
+
+	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
+	 * halted state. This will make the Rx side ready for reception.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET +  q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET +  q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) + q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p + (sizeof(*q->rxq_bd_v) *
+			    (lp->rx_bd_num - 1)));
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET + q->rx_offset);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET + q->rx_offset, chan_en);
+
+	return 0;
+
+out:
+	for_each_rx_dma_queue(lp, i) {
+		axienet_mcdma_rx_bd_free_tsn(ndev, lp->dq[i]);
+	}
+	return -ENOMEM;
+}
+
+static inline int get_mcdma_tx_q(struct axienet_local *lp, u32 chan_id)
+{
+	int i;
+
+	for_each_tx_dma_queue(lp, i) {
+		if (chan_id == lp->chan_num[i])
+			return lp->qnum[i];
+	}
+
+	return -ENODEV;
+}
+
+static inline int get_mcdma_rx_q(struct axienet_local *lp, u32 chan_id)
+{
+	int i;
+
+	for_each_rx_dma_queue(lp, i) {
+		if (chan_id == lp->chan_num[i])
+			return lp->qnum[i];
+	}
+
+	return -ENODEV;
+}
+
+static inline int map_dma_q_txirq(int irq, struct axienet_local *lp)
+{
+	int i, chan_sermask;
+	u16 chan_id = 1;
+	struct axienet_dma_q *q = lp->dq[0];
+
+	chan_sermask = axienet_dma_in32(q, XMCDMA_TXINT_SER_OFFSET);
+
+	for (i = 1, chan_id = 1; i != 0 && i <= chan_sermask;
+	     i <<= 1, chan_id++) {
+		if (chan_sermask & i)
+			return chan_id;
+	}
+
+	return -ENODEV;
+}
+
+irqreturn_t __maybe_unused axienet_mcdma_tx_irq_tsn(int irq, void *_ndev)
+{
+	u32 cr;
+	unsigned int status;
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i, j = map_dma_q_txirq(irq, lp);
+	struct axienet_dma_q *q;
+
+	if (j < 0)
+		return IRQ_NONE;
+
+	i = get_mcdma_tx_q(lp, j);
+	q = lp->dq[i];
+
+	status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id));
+	if (status & (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK)) {
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id), status);
+		axienet_start_xmit_done_tsn(lp->ndev, q);
+		goto out;
+	}
+	if (!(status & XMCDMA_IRQ_ALL_MASK))
+		return IRQ_NONE;
+	if (status & XMCDMA_IRQ_ERR_MASK) {
+		dev_err(&ndev->dev, "DMA Tx error 0x%x\n", status);
+		dev_err(&ndev->dev, "Current BD is at: %pa\n",
+			&q->txq_bd_v[q->tx_bd_ci].phys);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* Finally write to the Tx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      q->rx_offset);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* write to the Rx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  q->rx_offset, cr);
+
+		tasklet_schedule(&lp->dma_err_tasklet[i]);
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset, status);
+	}
+out:
+	return IRQ_HANDLED;
+}
+
+static inline int map_dma_q_rxirq(int irq, struct axienet_local *lp)
+{
+	int i, chan_sermask;
+	u16 chan_id = 1;
+	struct axienet_dma_q *q = lp->dq[0];
+
+	chan_sermask = axienet_dma_in32(q, XMCDMA_RXINT_SER_OFFSET +
+					q->rx_offset);
+
+	for (i = 1, chan_id = 1; i != 0 && i <= chan_sermask;
+		i <<= 1, chan_id++) {
+		if (chan_sermask & i)
+			return chan_id;
+	}
+
+	return -ENODEV;
+}
+
+irqreturn_t __maybe_unused axienet_mcdma_rx_irq_tsn(int irq, void *_ndev)
+{
+	u32 cr;
+	unsigned int status;
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i, j = map_dma_q_rxirq(irq, lp);
+	struct axienet_dma_q *q;
+
+	if (j < 0)
+		return IRQ_NONE;
+
+	i = get_mcdma_rx_q(lp, j);
+	q = lp->dq[i];
+
+	status = axienet_dma_in32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset);
+	if (status & (XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK)) {
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      q->rx_offset);
+		cr &= ~(XMCDMA_IRQ_IOC_MASK | XMCDMA_IRQ_DELAY_MASK);
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  q->rx_offset, cr);
+		napi_schedule(&lp->napi[i]);
+	}
+
+	if (!(status & XMCDMA_IRQ_ALL_MASK))
+		return IRQ_NONE;
+
+	if (status & XMCDMA_IRQ_ERR_MASK) {
+		dev_err(&ndev->dev, "DMA Rx error 0x%x\n", status);
+		dev_err(&ndev->dev, "Current BD is at: %pa\n",
+			&q->rxq_bd_v[q->rx_bd_ci].phys);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* Finally write to the Tx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+		cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				      q->rx_offset);
+		/* Disable coalesce, delay timer and error interrupts */
+		cr &= (~XMCDMA_IRQ_ALL_MASK);
+		/* write to the Rx channel control register */
+		axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				  q->rx_offset, cr);
+
+		tasklet_schedule(&lp->dma_err_tasklet[i]);
+		axienet_dma_out32(q, XMCDMA_CHAN_SR_OFFSET(q->chan_id) +
+				  q->rx_offset, status);
+	}
+
+	return IRQ_HANDLED;
+}
+
+void axienet_strings_tsn(struct net_device *ndev, u32 sset, u8 *data)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	int i = AXIENET_ETHTOOLS_SSTATS_LEN, j, k = 0, l = 0;
+	static const char tx_packets[] = "tx_packets";
+	static const char tx_bytes[] = "tx_bytes";
+	static const char rx_packets[] = "rx_packets";
+	static const char rx_bytes[] = "rx_bytes";
+
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_tx_queues)
+			break;
+		q = lp->dq[j];
+		if (!q) {
+			if (sset == ETH_SS_STATS) {
+				memcpy(data + l++ * ETH_GSTRING_LEN, tx_packets,
+				       sizeof(tx_packets));
+				memcpy(data + l++ * ETH_GSTRING_LEN, tx_bytes, sizeof(tx_bytes));
+				memcpy(data + l++ * ETH_GSTRING_LEN, rx_packets,
+				       sizeof(rx_packets));
+				memcpy(data + l++ * ETH_GSTRING_LEN, rx_bytes, sizeof(rx_bytes));
+			}
+			return;
+		}
+		if (i % 2 == 0)
+			k = (q->chan_id - 1) * 2;
+		if (sset == ETH_SS_STATS)
+			memcpy(data + i * ETH_GSTRING_LEN,
+			       axienet_get_tx_strings_stats[k].name,
+			       ETH_GSTRING_LEN);
+		++i;
+		k++;
+		if (i % 2 == 0)
+			++j;
+	}
+	k = 0;
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_RX_SSTATS_LEN(lp) +
+			AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_rx_queues)
+			break;
+		q = lp->dq[j];
+		if (!q) {
+			if (sset == ETH_SS_STATS) {
+				memcpy(data + l++ * ETH_GSTRING_LEN, tx_packets,
+				       sizeof(tx_packets));
+				memcpy(data + l++ * ETH_GSTRING_LEN, tx_bytes, sizeof(tx_bytes));
+				memcpy(data + l++ * ETH_GSTRING_LEN, rx_packets,
+				       sizeof(rx_packets));
+				memcpy(data + l++ * ETH_GSTRING_LEN, rx_bytes, sizeof(rx_bytes));
+			}
+			return;
+		}
+		if (i % 2 == 0)
+			k = (q->chan_id - 1) * 2;
+		if (sset == ETH_SS_STATS)
+			memcpy(data + i * ETH_GSTRING_LEN,
+			       axienet_get_rx_strings_stats[k].name,
+			       ETH_GSTRING_LEN);
+		++i;
+		k++;
+		if (i % 2 == 0)
+			++j;
+	}
+}
+
+int axienet_sset_count_tsn(struct net_device *ndev, int sset)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int i;
+
+	switch (sset) {
+	case ETH_SS_STATS:
+		for (i = 0; i < AXIENET_TX_SSTATS_LEN(lp); i++) {
+			if (!(lp->dq[i]))
+				return 4;
+		}
+		return (AXIENET_TX_SSTATS_LEN(lp) + AXIENET_RX_SSTATS_LEN(lp) +
+			AXIENET_ETHTOOLS_SSTATS_LEN);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+void axienet_get_stats_tsn(struct net_device *ndev,
+			   struct ethtool_stats *stats,
+			   u64 *data)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+	int i = AXIENET_ETHTOOLS_SSTATS_LEN, j, k = 0;
+
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_tx_queues)
+			break;
+
+		q = lp->dq[j];
+		if (!q) {
+			data[k++] = ndev->stats.tx_packets;
+			data[k++] = ndev->stats.tx_bytes;
+			data[k++] = ndev->stats.rx_packets;
+			data[k++] = ndev->stats.rx_bytes;
+			return;
+		}
+
+		data[i++] = q->tx_packets;
+		data[i++] = q->tx_bytes;
+		++j;
+	}
+	for (j = 0; i < AXIENET_TX_SSTATS_LEN(lp) + AXIENET_RX_SSTATS_LEN(lp) +
+			AXIENET_ETHTOOLS_SSTATS_LEN;) {
+		if (j >= lp->num_rx_queues)
+			break;
+
+		q = lp->dq[j];
+		if (!q) {
+			data[k++] = ndev->stats.tx_packets;
+			data[k++] = ndev->stats.tx_bytes;
+			data[k++] = ndev->stats.rx_packets;
+			data[k++] = ndev->stats.rx_bytes;
+			return;
+		}
+		data[i++] = q->rx_packets;
+		data[i++] = q->rx_bytes;
+		++j;
+	}
+}
+
+/**
+ * axienet_mcdma_err_handler_tsn - Tasklet handler for Axi MCDMA Error
+ * @data:	Data passed
+ *
+ * Resets the Axi MCDMA and Axi Ethernet devices, and reconfigures the
+ * Tx/Rx BDs.
+ */
+void __maybe_unused axienet_mcdma_err_handler_tsn(unsigned long data)
+{
+	u32 axienet_status;
+	u32 cr, i, chan_en;
+	struct axienet_dma_q *q = (struct axienet_dma_q *)data;
+	struct axienet_local *lp = q->lp;
+	struct net_device *ndev = lp->ndev;
+	struct aximcdma_bd *cur_p;
+
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+	__axienet_device_reset_tsn(q);
+
+	for (i = 0; i < lp->tx_bd_num; i++) {
+		cur_p = &q->txq_bd_v[i];
+		if (cur_p->phys)
+			dma_unmap_single(ndev->dev.parent, cur_p->phys,
+					 (cur_p->cntrl &
+					  XAXIDMA_BD_CTRL_LENGTH_MASK),
+					 DMA_TO_DEVICE);
+		if (cur_p->tx_skb)
+			dev_kfree_skb_irq((struct sk_buff *)cur_p->tx_skb);
+		cur_p->phys = 0;
+		cur_p->cntrl = 0;
+		cur_p->status = 0;
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app3 = 0;
+		cur_p->app4 = 0;
+		cur_p->sw_id_offset = 0;
+		cur_p->tx_skb = 0;
+	}
+
+	for (i = 0; i < lp->rx_bd_num; i++) {
+		cur_p = &q->rxq_bd_v[i];
+		cur_p->status = 0;
+		cur_p->app0 = 0;
+		cur_p->app1 = 0;
+		cur_p->app2 = 0;
+		cur_p->app3 = 0;
+		cur_p->app4 = 0;
+	}
+
+	q->tx_bd_ci = 0;
+	q->tx_bd_tail = 0;
+	q->rx_bd_ci = 0;
+
+	/* Start updating the Rx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			      q->rx_offset);
+	/* Update the interrupt coalesce count */
+	cr = ((cr & ~XMCDMA_COALESCE_MASK) |
+	      ((lp->coalesce_count_rx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = ((cr & ~XMCDMA_DELAY_MASK) |
+	      (XAXIDMA_DFT_RX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Rx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+			  q->rx_offset, cr);
+
+	/* Start updating the Tx channel control register */
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	/* Update the interrupt coalesce count */
+	cr = (((cr & ~XMCDMA_COALESCE_MASK)) |
+	      ((lp->coalesce_count_tx) << XMCDMA_COALESCE_SHIFT));
+	/* Update the delay timer count */
+	cr = (((cr & ~XMCDMA_DELAY_MASK)) |
+	      (XAXIDMA_DFT_TX_WAITBOUND << XMCDMA_DELAY_SHIFT));
+	/* Enable coalesce, delay timer and error interrupts */
+	cr |= XMCDMA_IRQ_ALL_MASK;
+	/* Write to the Tx channel control register */
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id), cr);
+
+	/* Populate the tail pointer and bring the Rx Axi DMA engine out of
+	 * halted state. This will make the Rx side ready for reception.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET +  q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET +  q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) +
+				q->rx_offset);
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id) + q->rx_offset,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	axienet_dma_bdout(q, XMCDMA_CHAN_TAILDESC_OFFSET(q->chan_id) +
+			    q->rx_offset, q->rx_bd_p + (sizeof(*q->rxq_bd_v) *
+			    (lp->rx_bd_num - 1)));
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET + q->rx_offset);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET + q->rx_offset, chan_en);
+
+	/* Write to the RS (Run-stop) bit in the Tx channel control register.
+	 * Tx channel is now ready to run. But only after we write to the
+	 * tail pointer register that the Tx channel will start transmitting.
+	 */
+	axienet_dma_bdout(q, XMCDMA_CHAN_CURDESC_OFFSET(q->chan_id),
+			  q->tx_bd_p);
+	cr = axienet_dma_in32(q, XMCDMA_CR_OFFSET);
+	axienet_dma_out32(q, XMCDMA_CR_OFFSET,
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	cr = axienet_dma_in32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id));
+	axienet_dma_out32(q, XMCDMA_CHAN_CR_OFFSET(q->chan_id),
+			  cr | XMCDMA_CR_RUNSTOP_MASK);
+	chan_en = axienet_dma_in32(q, XMCDMA_CHEN_OFFSET);
+	chan_en |= (1 << (q->chan_id - 1));
+	axienet_dma_out32(q, XMCDMA_CHEN_OFFSET, chan_en);
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC) {
+		axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+		axienet_status &= ~XAE_RCW1_RX_MASK;
+		axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
+	}
+
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf) {
+		axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+		if (axienet_status & XAE_INT_RXRJECT_MASK)
+			axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+	}
+
+	if (lp->axienet_config->mactype != XAXIENET_10G_25G &&
+	    lp->axienet_config->mactype != XAXIENET_MRMAC)
+		axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+	axienet_set_mac_address_tsn(ndev, NULL);
+	axienet_set_multicast_list_tsn(ndev);
+	lp->axienet_config->setoptions(ndev, lp->options);
+}
+
+int __maybe_unused axienet_mcdma_tx_probe_tsn(struct platform_device *pdev,
+					      struct device_node *np,
+					      struct axienet_local *lp)
+{
+	int i;
+	char dma_name[24];
+
+	u32 num = XAE_TSN_MIN_QUEUES;
+	int ret = 0;
+	/* get number of associated queues */
+	ret = of_property_read_u32(np, "xlnx,num-mm2s-channels", &num);
+	if (ret)
+		num = XAE_TSN_MIN_QUEUES;
+	lp->num_tx_queues = num;
+
+	for_each_tx_dma_queue(lp, i) {
+		struct axienet_dma_q *q;
+
+		q = lp->dq[i];
+
+		q->dma_regs = lp->mcdma_regs;
+		snprintf(dma_name, sizeof(dma_name), "mm2s_ch%d_introut",
+			 q->chan_id);
+		q->tx_irq = of_irq_get_byname(np, dma_name);
+		q->eth_hasdre = of_property_read_bool(np,
+						      "xlnx,include-mm2s-dre");
+		spin_lock_init(&q->tx_lock);
+	}
+	of_node_put(np);
+
+	return 0;
+}
+
+int __maybe_unused axienet_mcdma_rx_probe_tsn(struct platform_device *pdev,
+					      struct device_node *np,
+					      struct net_device *ndev)
+{
+	int i;
+	char dma_name[24];
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	for_each_rx_dma_queue(lp, i) {
+		struct axienet_dma_q *q;
+
+		q = lp->dq[i];
+
+		q->dma_regs = lp->mcdma_regs;
+		snprintf(dma_name, sizeof(dma_name), "s2mm_ch%d_introut",
+			 q->chan_id);
+		q->rx_irq = of_irq_get_byname(np, dma_name);
+		spin_lock_init(&q->rx_lock);
+
+		netif_napi_add(ndev, &lp->napi[i], xaxienet_rx_poll_tsn,
+			       XAXIENET_NAPI_WEIGHT);
+	}
+
+	return 0;
+}
+
+static ssize_t rxch_obs1_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS1_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 1 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs2_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS2_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 2 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs3_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS3_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 3 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs4_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS4_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 4 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs5_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS5_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 5 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t rxch_obs6_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS6_OFFSET + q->rx_offset);
+
+	return sprintf(buf, "Ingress Channel Observer 6 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs1_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS1_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 1 Contents is 0x%x\n",
+		       reg);
+}
+
+static ssize_t txch_obs2_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS2_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 2 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs3_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS3_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 3 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs4_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS4_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 4 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs5_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS5_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 5 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t txch_obs6_show(struct device *dev,
+			      struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	u32 reg;
+
+	reg = axienet_dma_in32(q, XMCDMA_CHOBS6_OFFSET);
+
+	return sprintf(buf, "Egress Channel Observer 6 Contents is 0x%x\n\r",
+		       reg);
+}
+
+static ssize_t chan_weight_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	return sprintf(buf, "chan_id is %d and weight is %d\n",
+		       lp->chan_id, lp->weight);
+}
+
+static ssize_t chan_weight_store(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q = lp->dq[0];
+	int ret;
+	u16 flags, chan_id;
+	u32 val;
+
+	ret = kstrtou16(buf, 16, &flags);
+	if (ret)
+		return ret;
+
+	lp->chan_id = (flags & 0xF0) >> 4;
+	lp->weight = flags & 0x0F;
+
+	if (lp->chan_id < 8)
+		val = axienet_dma_in32(q, XMCDMA_TXWEIGHT0_OFFSET);
+	else
+		val = axienet_dma_in32(q, XMCDMA_TXWEIGHT1_OFFSET);
+
+	if (lp->chan_id > 7)
+		chan_id = lp->chan_id - 8;
+	else
+		chan_id = lp->chan_id;
+
+	val &= ~XMCDMA_TXWEIGHT_CH_MASK(chan_id);
+	val |= lp->weight << XMCDMA_TXWEIGHT_CH_SHIFT(chan_id);
+
+	if (lp->chan_id < 8)
+		axienet_dma_out32(q, XMCDMA_TXWEIGHT0_OFFSET, val);
+	else
+		axienet_dma_out32(q, XMCDMA_TXWEIGHT1_OFFSET, val);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(chan_weight);
+static DEVICE_ATTR_RO(rxch_obs1);
+static DEVICE_ATTR_RO(rxch_obs2);
+static DEVICE_ATTR_RO(rxch_obs3);
+static DEVICE_ATTR_RO(rxch_obs4);
+static DEVICE_ATTR_RO(rxch_obs5);
+static DEVICE_ATTR_RO(rxch_obs6);
+static DEVICE_ATTR_RO(txch_obs1);
+static DEVICE_ATTR_RO(txch_obs2);
+static DEVICE_ATTR_RO(txch_obs3);
+static DEVICE_ATTR_RO(txch_obs4);
+static DEVICE_ATTR_RO(txch_obs5);
+static DEVICE_ATTR_RO(txch_obs6);
+static const struct attribute *mcdma_attrs[] = {
+	&dev_attr_chan_weight.attr,
+	&dev_attr_rxch_obs1.attr,
+	&dev_attr_rxch_obs2.attr,
+	&dev_attr_rxch_obs3.attr,
+	&dev_attr_rxch_obs4.attr,
+	&dev_attr_rxch_obs5.attr,
+	&dev_attr_rxch_obs6.attr,
+	&dev_attr_txch_obs1.attr,
+	&dev_attr_txch_obs2.attr,
+	&dev_attr_txch_obs3.attr,
+	&dev_attr_txch_obs4.attr,
+	&dev_attr_txch_obs5.attr,
+	&dev_attr_txch_obs6.attr,
+	NULL,
+};
+
+static const struct attribute_group mcdma_attributes = {
+	.attrs = (struct attribute **)mcdma_attrs,
+};
+
+int axeinet_mcdma_create_sysfs_tsn(struct kobject *kobj)
+{
+	return sysfs_create_group(kobj, &mcdma_attributes);
+}
+
+void axeinet_mcdma_remove_sysfs_tsn(struct kobject *kobj)
+{
+	sysfs_remove_group(kobj, &mcdma_attributes);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_axienet_tsn.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_axienet_tsn.h
@@ -0,0 +1,1354 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Definitions for Xilinx Axi Ethernet device driver.
+ *
+ * Copyright (c) 2009 Secret Lab Technologies, Ltd.
+ * Copyright (c) 2010 - 2012 Xilinx, Inc. All rights reserved.
+ */
+
+#ifndef XILINX_AXIENET_TSN_H
+#define XILINX_AXIENET_TSN_H
+
+#include <linux/netdevice.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/if_vlan.h>
+#include <linux/net_tstamp.h>
+#include <linux/phy.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
+
+/* Packet size info */
+#define XAE_HDR_SIZE			14 /* Size of Ethernet header */
+#define XAE_TRL_SIZE			 4 /* Size of Ethernet trailer (FCS) */
+#define XAE_MTU			      1500 /* Max MTU of an Ethernet frame */
+#define XAE_JUMBO_MTU		      9000 /* Max MTU of a jumbo Eth. frame */
+
+#define XAE_MAX_FRAME_SIZE	 (XAE_MTU + XAE_HDR_SIZE + XAE_TRL_SIZE)
+#define XAE_MAX_VLAN_FRAME_SIZE  (XAE_MTU + VLAN_ETH_HLEN + XAE_TRL_SIZE)
+#define XAE_MAX_JUMBO_FRAME_SIZE (XAE_JUMBO_MTU + XAE_HDR_SIZE + XAE_TRL_SIZE)
+
+/* Queue Numbers of BE, RES, ST and PTP */
+
+#define BE_QUEUE_NUMBER  0
+#define RES_QUEUE_NUMBER 1
+#define ST_QUEUE_NUMBER  2
+#define PTP_QUEUE_NUMBER 3
+
+/* DMA address width min and max range */
+#define XAE_DMA_MASK_MIN	32
+#define XAE_DMA_MASK_MAX	64
+
+/* In AXI DMA Tx and Rx queue count is same */
+#define for_each_tx_dma_queue(lp, var) \
+	for ((var) = 0; (var) < (lp)->num_tx_queues; (var)++)
+
+#define for_each_rx_dma_queue(lp, var) \
+	for ((var) = 0; (var) < (lp)->num_rx_queues; (var)++)
+/* Configuration options */
+
+/* Accept all incoming packets. Default: disabled (cleared) */
+#define XAE_OPTION_PROMISC			BIT(0)
+
+/* Jumbo frame support for Tx & Rx. Default: disabled (cleared) */
+#define XAE_OPTION_JUMBO			BIT(1)
+
+/* VLAN Rx & Tx frame support. Default: disabled (cleared) */
+#define XAE_OPTION_VLAN				BIT(2)
+
+/* Enable recognition of flow control frames on Rx. Default: enabled (set) */
+#define XAE_OPTION_FLOW_CONTROL			BIT(4)
+
+/* Strip FCS and PAD from incoming frames. Note: PAD from VLAN frames is not
+ * stripped. Default: disabled (set)
+ */
+#define XAE_OPTION_FCS_STRIP			BIT(5)
+
+/* Generate FCS field and add PAD automatically for outgoing frames.
+ * Default: enabled (set)
+ */
+#define XAE_OPTION_FCS_INSERT			BIT(6)
+
+/* Enable Length/Type error checking for incoming frames. When this option is
+ * set, the MAC will filter frames that have a mismatched type/length field
+ * and if XAE_OPTION_REPORT_RXERR is set, the user is notified when these
+ * types of frames are encountered. When this option is cleared, the MAC will
+ * allow these types of frames to be received. Default: enabled (set)
+ */
+#define XAE_OPTION_LENTYPE_ERR			BIT(7)
+
+/* Enable the transmitter. Default: enabled (set) */
+#define XAE_OPTION_TXEN				BIT(11)
+
+/*  Enable the receiver. Default: enabled (set) */
+#define XAE_OPTION_RXEN				BIT(12)
+
+/*  Default options set when device is initialized or reset */
+#define XAE_OPTION_DEFAULTS				   \
+				(XAE_OPTION_TXEN |	   \
+				 XAE_OPTION_FLOW_CONTROL | \
+				 XAE_OPTION_RXEN)
+
+/* Axi DMA Register definitions */
+
+#define XAXIDMA_TX_CR_OFFSET	0x00000000 /* Channel control */
+#define XAXIDMA_TX_SR_OFFSET	0x00000004 /* Status */
+#define XAXIDMA_TX_CDESC_OFFSET	0x00000008 /* Current descriptor pointer */
+#define XAXIDMA_TX_TDESC_OFFSET	0x00000010 /* Tail descriptor pointer */
+
+#define XAXIDMA_RX_CR_OFFSET	0x00000030 /* Channel control */
+#define XAXIDMA_RX_SR_OFFSET	0x00000034 /* Status */
+#define XAXIDMA_RX_CDESC_OFFSET	0x00000038 /* Current descriptor pointer */
+#define XAXIDMA_RX_TDESC_OFFSET	0x00000040 /* Tail descriptor pointer */
+
+#define XAXIDMA_CR_RUNSTOP_MASK	0x00000001 /* Start/stop DMA channel */
+#define XAXIDMA_CR_RESET_MASK	0x00000004 /* Reset DMA engine */
+
+#define XAXIDMA_SR_HALT_MASK	0x00000001 /* Indicates DMA channel halted */
+
+#define XAXIDMA_BD_NDESC_OFFSET		0x00 /* Next descriptor pointer */
+#define XAXIDMA_BD_BUFA_OFFSET		0x08 /* Buffer address */
+#define XAXIDMA_BD_CTRL_LEN_OFFSET	0x18 /* Control/buffer length */
+#define XAXIDMA_BD_STS_OFFSET		0x1C /* Status */
+#define XAXIDMA_BD_USR0_OFFSET		0x20 /* User IP specific word0 */
+#define XAXIDMA_BD_USR1_OFFSET		0x24 /* User IP specific word1 */
+#define XAXIDMA_BD_USR2_OFFSET		0x28 /* User IP specific word2 */
+#define XAXIDMA_BD_USR3_OFFSET		0x2C /* User IP specific word3 */
+#define XAXIDMA_BD_USR4_OFFSET		0x30 /* User IP specific word4 */
+#define XAXIDMA_BD_ID_OFFSET		0x34 /* Sw ID */
+#define XAXIDMA_BD_HAS_STSCNTRL_OFFSET	0x38 /* Whether has stscntrl strm */
+#define XAXIDMA_BD_HAS_DRE_OFFSET	0x3C /* Whether has DRE */
+
+#define XAXIDMA_BD_HAS_DRE_SHIFT	8 /* Whether has DRE shift */
+#define XAXIDMA_BD_HAS_DRE_MASK		0xF00 /* Whether has DRE mask */
+#define XAXIDMA_BD_WORDLEN_MASK		0xFF /* Whether has DRE mask */
+
+#define XAXIDMA_BD_CTRL_LENGTH_MASK	0x007FFFFF /* Requested len */
+#define XAXIDMA_BD_CTRL_TXSOF_MASK	0x08000000 /* First tx packet */
+#define XAXIDMA_BD_CTRL_TXEOF_MASK	0x04000000 /* Last tx packet */
+#define XAXIDMA_BD_CTRL_ALL_MASK	0x0C000000 /* All control bits */
+
+#define XAXIDMA_DELAY_MASK		0xFF000000 /* Delay timeout counter */
+#define XAXIDMA_COALESCE_MASK		0x00FF0000 /* Coalesce counter */
+
+#define XAXIDMA_DELAY_SHIFT		24
+#define XAXIDMA_COALESCE_SHIFT		16
+
+#define XAXIDMA_IRQ_IOC_MASK		0x00001000 /* Completion intr */
+#define XAXIDMA_IRQ_DELAY_MASK		0x00002000 /* Delay interrupt */
+#define XAXIDMA_IRQ_ERROR_MASK		0x00004000 /* Error interrupt */
+#define XAXIDMA_IRQ_ALL_MASK		0x00007000 /* All interrupts */
+
+/* Default TX/RX Threshold and waitbound values for SGDMA mode */
+#define XAXIDMA_DFT_TX_THRESHOLD	24
+#define XAXIDMA_DFT_TX_WAITBOUND	254
+#define XAXIDMA_DFT_RX_THRESHOLD	1
+#define XAXIDMA_DFT_RX_WAITBOUND	254
+
+#define XAXIDMA_BD_CTRL_TXSOF_MASK	0x08000000 /* First tx packet */
+#define XAXIDMA_BD_CTRL_TXEOF_MASK	0x04000000 /* Last tx packet */
+#define XAXIDMA_BD_CTRL_ALL_MASK	0x0C000000 /* All control bits */
+
+#define XAXIDMA_BD_STS_ACTUAL_LEN_MASK	0x007FFFFF /* Actual len */
+#define XAXIDMA_BD_STS_COMPLETE_MASK	0x80000000 /* Completed */
+#define XAXIDMA_BD_STS_DEC_ERR_MASK	0x40000000 /* Decode error */
+#define XAXIDMA_BD_STS_SLV_ERR_MASK	0x20000000 /* Slave error */
+#define XAXIDMA_BD_STS_INT_ERR_MASK	0x10000000 /* Internal err */
+#define XAXIDMA_BD_STS_ALL_ERR_MASK	0x70000000 /* All errors */
+#define XAXIDMA_BD_STS_RXSOF_MASK	0x08000000 /* First rx pkt */
+#define XAXIDMA_BD_STS_RXEOF_MASK	0x04000000 /* Last rx pkt */
+#define XAXIDMA_BD_STS_ALL_MASK		0xFC000000 /* All status bits */
+
+#define XAXIDMA_BD_MINIMUM_ALIGNMENT	0x40
+
+/* AXI Tx Timestamp Stream FIFO Register Definitions */
+#define XAXIFIFO_TXTS_ISR	0x00000000 /* Interrupt Status Register */
+#define XAXIFIFO_TXTS_TDFV	0x0000000C /* Transmit Data FIFO Vacancy */
+#define XAXIFIFO_TXTS_TXFD	0x00000010 /* Tx Data Write Port */
+#define XAXIFIFO_TXTS_TLR	0x00000014 /* Transmit Length Register */
+#define XAXIFIFO_TXTS_RFO	0x0000001C /* Rx Fifo Occupancy */
+#define XAXIFIFO_TXTS_RDFR	0x00000018 /* Rx Fifo reset */
+#define XAXIFIFO_TXTS_RXFD	0x00000020 /* Rx Data Read Port */
+#define XAXIFIFO_TXTS_RLR	0x00000024 /* Receive Length Register */
+#define XAXIFIFO_TXTS_SRR	0x00000028 /* AXI4-Stream Reset */
+
+#define XAXIFIFO_TXTS_INT_RC_MASK	0x04000000
+#define XAXIFIFO_TXTS_RXFD_MASK		0x7FFFFFFF
+#define XAXIFIFO_TXTS_RESET_MASK	0x000000A5
+#define XAXIFIFO_TXTS_TAG_MASK		0xFFFF0000
+#define XAXIFIFO_TXTS_TAG_SHIFT		16
+#define XAXIFIFO_TXTS_TAG_MAX		0xFFFE
+
+/* Axi Ethernet registers definition */
+#define XAE_RAF_OFFSET		0x00000000 /* Reset and Address filter */
+#define XAE_TPF_OFFSET		0x00000004 /* Tx Pause Frame */
+#define XAE_IFGP_OFFSET		0x00000008 /* Tx Inter-frame gap adjustment*/
+#define XAE_IS_OFFSET		0x0000000C /* Interrupt status */
+#define XAE_IP_OFFSET		0x00000010 /* Interrupt pending */
+#define XAE_IE_OFFSET		0x00000014 /* Interrupt enable */
+#define XAE_TTAG_OFFSET		0x00000018 /* Tx VLAN TAG */
+#define XAE_RTAG_OFFSET		0x0000001C /* Rx VLAN TAG */
+#define XAE_UAWL_OFFSET		0x00000020 /* Unicast address word lower */
+#define XAE_UAWU_OFFSET		0x00000024 /* Unicast address word upper */
+#define XAE_TPID0_OFFSET	0x00000028 /* VLAN TPID0 register */
+#define XAE_TPID1_OFFSET	0x0000002C /* VLAN TPID1 register */
+#define XAE_PPST_OFFSET		0x00000030 /* PCS PMA Soft Temac Status Reg */
+#define XAE_RCW0_OFFSET		0x00000400 /* Rx Configuration Word 0 */
+#define XAE_RCW1_OFFSET		0x00000404 /* Rx Configuration Word 1 */
+#define XAE_TC_OFFSET		0x00000408 /* Tx Configuration */
+#define XAE_FCC_OFFSET		0x0000040C /* Flow Control Configuration */
+#define XAE_ID_OFFSET		0x000004F8 /* Identification register */
+#define XAE_EMMC_OFFSET		0x00000410 /* MAC speed configuration */
+#define XAE_RMFC_OFFSET		0x00000414 /* RX Max Frame Configuration */
+#define XAE_TSN_ABL_OFFSET	0x000004FC /* Ability Register */
+#define XAE_MDIO_MC_OFFSET	0x00000500 /* MDIO Setup */
+#define XAE_MDIO_MCR_OFFSET	0x00000504 /* MDIO Control */
+#define XAE_MDIO_MWD_OFFSET	0x00000508 /* MDIO Write Data */
+#define XAE_MDIO_MRD_OFFSET	0x0000050C /* MDIO Read Data */
+#define XAE_TEMAC_IS_OFFSET	0x00000600 /* TEMAC Interrupt Status */
+#define XAE_TEMAC_IP_OFFSET	0x00000610 /* TEMAC Interrupt Pending Status */
+#define XAE_TEMAC_IE_OFFSET	0x00000620 /* TEMAC Interrupt Enable Status */
+#define XAE_TEMAC_IC_OFFSET	0x00000630 /* TEMAC Interrupt Clear Status */
+#define XAE_UAW0_OFFSET		0x00000700 /* Unicast address word 0 */
+#define XAE_UAW1_OFFSET		0x00000704 /* Unicast address word 1 */
+#define XAE_FMC_OFFSET		0x00000708 /* Frame Filter Control */
+#define XAE_AF0_OFFSET		0x00000710 /* Address Filter 0 */
+#define XAE_AF1_OFFSET		0x00000714 /* Address Filter 1 */
+#define XAE_FF_3_OFFSET		0x0000071C /* Frame Filter 3 */
+#define XAE_FF_5_OFFSET		0x00000724 /* Frame Filter 5 */
+#define XAE_FF_9_OFFSET		0x00000734 /* Frame Filter 9 */
+#define XAE_FF_10_OFFSET	0x00000738 /* Frame Filter 10 */
+#define XAE_AF0_MASK_OFFSET	0x00000750 /* Address Filter Mask 0 */
+#define XAE_AF1_MASK_OFFSET	0x00000754 /* Address Filter Mask 1 */
+#define XAE_FF_5_MASK_OFFSET	0x00000764 /* Frame Filter Mask register 5 */
+#define XAE_FF_9_MASK_OFFSET	0x00000774 /* Frame Filter Mask register 9 */
+#define XAE_FF_10_MASK_OFFSET	0x00000778 /* Frame Filter Mask register 10 */
+
+#define XAE_TX_VLAN_DATA_OFFSET 0x00004000 /* TX VLAN data table address */
+#define XAE_RX_VLAN_DATA_OFFSET 0x00008000 /* RX VLAN data table address */
+#define XAE_MCAST_TABLE_OFFSET	0x00020000 /* Multicast table address */
+
+/* Bit Masks for Axi Ethernet RAF register */
+/* Reject receive multicast destination address */
+#define XAE_RAF_MCSTREJ_MASK		0x00000002
+/* Reject receive broadcast destination address */
+#define XAE_RAF_BCSTREJ_MASK		0x00000004
+#define XAE_RAF_TXVTAGMODE_MASK		0x00000018 /* Tx VLAN TAG mode */
+#define XAE_RAF_RXVTAGMODE_MASK		0x00000060 /* Rx VLAN TAG mode */
+#define XAE_RAF_TXVSTRPMODE_MASK	0x00000180 /* Tx VLAN STRIP mode */
+#define XAE_RAF_RXVSTRPMODE_MASK	0x00000600 /* Rx VLAN STRIP mode */
+#define XAE_RAF_NEWFNCENBL_MASK		0x00000800 /* New function mode */
+/* Extended Multicast Filtering mode */
+#define XAE_RAF_EMULTIFLTRENBL_MASK	0x00001000
+#define XAE_RAF_STATSRST_MASK		0x00002000 /* Stats. Counter Reset */
+#define XAE_RAF_RXBADFRMEN_MASK		0x00004000 /* Recv Bad Frame Enable */
+#define XAE_RAF_TXVTAGMODE_SHIFT	3 /* Tx Tag mode shift bits */
+#define XAE_RAF_RXVTAGMODE_SHIFT	5 /* Rx Tag mode shift bits */
+#define XAE_RAF_TXVSTRPMODE_SHIFT	7 /* Tx strip mode shift bits*/
+#define XAE_RAF_RXVSTRPMODE_SHIFT	9 /* Rx Strip mode shift bits*/
+
+/* Bit Masks for Axi Ethernet TPF and IFGP registers */
+#define XAE_TPF_TPFV_MASK		0x0000FFFF /* Tx pause frame value */
+/* Transmit inter-frame gap adjustment value */
+#define XAE_IFGP0_IFGP_MASK		0x0000007F
+
+/* Bit Masks for Axi Ethernet IS, IE and IP registers, Same masks apply
+ * for all 3 registers.
+ */
+/* Hard register access complete */
+#define XAE_INT_HARDACSCMPLT_MASK	0x00000001
+/* Auto negotiation complete */
+#define XAE_INT_AUTONEG_MASK		0x00000002
+#define XAE_INT_RXCMPIT_MASK		0x00000004 /* Rx complete */
+#define XAE_INT_RXRJECT_MASK		0x00000008 /* Rx frame rejected */
+#define XAE_INT_RXFIFOOVR_MASK		0x00000010 /* Rx fifo overrun */
+#define XAE_INT_TXCMPIT_MASK		0x00000020 /* Tx complete */
+#define XAE_INT_RXDCMLOCK_MASK		0x00000040 /* Rx Dcm Lock */
+#define XAE_INT_MGTRDY_MASK		0x00000080 /* MGT clock Lock */
+#define XAE_INT_PHYRSTCMPLT_MASK	0x00000100 /* Phy Reset complete */
+#define XAE_INT_ALL_MASK		0x0000003F /* All the ints */
+
+/* INT bits that indicate receive errors */
+#define XAE_INT_RECV_ERROR_MASK				\
+	(XAE_INT_RXRJECT_MASK | XAE_INT_RXFIFOOVR_MASK)
+
+/* Bit masks for Axi Ethernet VLAN TPID Word 0 register */
+#define XAE_TPID_0_MASK		0x0000FFFF /* TPID 0 */
+#define XAE_TPID_1_MASK		0xFFFF0000 /* TPID 1 */
+
+/* Bit masks for Axi Ethernet VLAN TPID Word 1 register */
+#define XAE_TPID_2_MASK		0x0000FFFF /* TPID 0 */
+#define XAE_TPID_3_MASK		0xFFFF0000 /* TPID 1 */
+
+/* Bit masks for Axi Ethernet RCW1 register */
+#define XAE_RCW1_INBAND1588_MASK 0x00400000 /* Inband 1588 Enable */
+#define XAE_RCW1_RST_MASK	0x80000000 /* Reset */
+#define XAE_RCW1_JUM_MASK	0x40000000 /* Jumbo frame enable */
+/* In-Band FCS enable (FCS not stripped) */
+#define XAE_RCW1_FCS_MASK	0x20000000
+#define XAE_RCW1_RX_MASK	0x10000000 /* Receiver enable */
+#define XAE_RCW1_VLAN_MASK	0x08000000 /* VLAN frame enable */
+/* Length/type field valid check disable */
+#define XAE_RCW1_LT_DIS_MASK	0x02000000
+/* Control frame Length check disable */
+#define XAE_RCW1_CL_DIS_MASK	0x01000000
+/* Pause frame source address bits [47:32]. Bits [31:0] are
+ * stored in register RCW0
+ */
+#define XAE_RCW1_PAUSEADDR_MASK 0x0000FFFF
+
+/* Bit masks for Axi Ethernet TC register */
+#define XAE_TC_INBAND1588_MASK 0x00400000 /* Inband 1588 Enable */
+#define XAE_TC_RST_MASK		0x80000000 /* Reset */
+#define XAE_TC_JUM_MASK		0x40000000 /* Jumbo frame enable */
+/* In-Band FCS enable (FCS not generated) */
+#define XAE_TC_FCS_MASK		0x20000000
+#define XAE_TC_TX_MASK		0x10000000 /* Transmitter enable */
+#define XAE_TC_VLAN_MASK	0x08000000 /* VLAN frame enable */
+/* Inter-frame gap adjustment enable */
+#define XAE_TC_IFG_MASK		0x02000000
+
+/* Bit masks for Axi Ethernet FCC register */
+#define XAE_FCC_FCRX_MASK	0x20000000 /* Rx flow control enable */
+#define XAE_FCC_FCTX_MASK	0x40000000 /* Tx flow control enable */
+
+/* Bit masks for Axi Ethernet EMMC register */
+#define XAE_EMMC_LINKSPEED_MASK	0xC0000000 /* Link speed */
+#define XAE_EMMC_RGMII_MASK	0x20000000 /* RGMII mode enable */
+#define XAE_EMMC_SGMII_MASK	0x10000000 /* SGMII mode enable */
+#define XAE_EMMC_GPCS_MASK	0x08000000 /* 1000BaseX mode enable */
+#define XAE_EMMC_HOST_MASK	0x04000000 /* Host interface enable */
+#define XAE_EMMC_TX16BIT	0x02000000 /* 16 bit Tx client enable */
+#define XAE_EMMC_RX16BIT	0x01000000 /* 16 bit Rx client enable */
+#define XAE_EMMC_LINKSPD_10	0x00000000 /* Link Speed mask for 10 Mbit */
+#define XAE_EMMC_LINKSPD_100	0x40000000 /* Link Speed mask for 100 Mbit */
+#define XAE_EMMC_LINKSPD_1000	0x80000000 /* Link Speed mask for 1000 Mbit */
+#define XAE_EMMC_LINKSPD_2500	0x80000000 /* Link Speed mask for 2500 Mbit */
+
+/* Bit masks for Axi Ethernet MDIO interface MC register */
+#define XAE_MDIO_MC_MDIOEN_MASK		0x00000040 /* MII management enable */
+#define XAE_MDIO_MC_CLOCK_DIVIDE_MAX	0x3F	   /* Maximum MDIO divisor */
+
+/* Bit masks for Axi Ethernet MDIO interface MCR register */
+#define XAE_MDIO_MCR_PHYAD_MASK		0x1F000000 /* Phy Address Mask */
+#define XAE_MDIO_MCR_PHYAD_SHIFT	24	   /* Phy Address Shift */
+#define XAE_MDIO_MCR_REGAD_MASK		0x001F0000 /* Reg Address Mask */
+#define XAE_MDIO_MCR_REGAD_SHIFT	16	   /* Reg Address Shift */
+#define XAE_MDIO_MCR_OP_MASK		0x0000C000 /* Operation Code Mask */
+#define XAE_MDIO_MCR_OP_SHIFT		13	   /* Operation Code Shift */
+#define XAE_MDIO_MCR_OP_READ_MASK	0x00008000 /* Op Code Read Mask */
+#define XAE_MDIO_MCR_OP_WRITE_MASK	0x00004000 /* Op Code Write Mask */
+#define XAE_MDIO_MCR_INITIATE_MASK	0x00000800 /* Ready Mask */
+#define XAE_MDIO_MCR_READY_MASK		0x00000080 /* Ready Mask */
+
+/* Bit masks for Axi Ethernet UAW1 register */
+/* Station address bits [47:32]; Station address
+ * bits [31:0] are stored in register UAW0
+ */
+#define XAE_UAW1_UNICASTADDR_MASK	0x0000FFFF
+
+/* Bit masks for Axi Ethernet FMC register */
+#define XAE_FMC_PM_MASK			0x80000000 /* Promis. mode enable */
+#define XAE_FMC_IND_MASK		0x00000003 /* Index Mask */
+
+#define XAE_MDIO_DIV_DFT		29 /* Default MDIO clock divisor */
+
+/* Total number of entries in the hardware multicast table. */
+#define XAE_MULTICAST_CAM_TABLE_NUM	4
+
+/* Axi Ethernet Synthesis features */
+#define XAE_FEATURE_PARTIAL_RX_CSUM	BIT(0)
+#define XAE_FEATURE_PARTIAL_TX_CSUM	BIT(1)
+#define XAE_FEATURE_FULL_RX_CSUM	BIT(2)
+#define XAE_FEATURE_FULL_TX_CSUM	BIT(3)
+#define XAE_FEATURE_DMA_64BIT		BIT(4)
+
+#define XAE_NO_CSUM_OFFLOAD		0
+
+#define XAE_FULL_CSUM_STATUS_MASK	0x00000038
+#define XAE_IP_UDP_CSUM_VALIDATED	0x00000003
+#define XAE_IP_TCP_CSUM_VALIDATED	0x00000002
+
+#define DELAY_OF_ONE_MILLISEC		1000
+
+#define XAXIENET_NAPI_WEIGHT		64
+
+/* Definition of 1588 PTP in Axi Ethernet IP */
+#define TX_TS_OP_NOOP           0x0
+#define TX_TS_OP_ONESTEP        0x1
+#define TX_TS_OP_TWOSTEP        0x2
+#define TX_TS_CSUM_UPDATE       0x1
+#define TX_TS_CSUM_UPDATE_MRMAC		0x4
+#define TX_TS_PDELAY_UPDATE_MRMAC	0x8
+#define TX_PTP_CSUM_OFFSET      0x28
+#define TX_PTP_TS_OFFSET        0x4C
+#define TX_PTP_CF_OFFSET        0x32
+
+/* XXV MAC Register Definitions */
+#define XXV_GT_RESET_OFFSET		0x00000000
+#define XXV_TC_OFFSET			0x0000000C
+#define XXV_RCW1_OFFSET			0x00000014
+#define XXV_JUM_OFFSET			0x00000018
+#define XXV_TICKREG_OFFSET		0x00000020
+#define XXV_STATRX_BLKLCK_OFFSET	0x0000040C
+#define XXV_USXGMII_AN_OFFSET		0x000000C8
+#define XXV_USXGMII_AN_STS_OFFSET	0x00000458
+#define XXV_STAT_GTWIZ_OFFSET		0x000004A0
+#define XXV_CONFIG_REVISION		0x00000024
+
+/* XXV MAC Register Mask Definitions */
+#define XXV_GT_RESET_MASK	BIT(0)
+#define XXV_TC_TX_MASK		BIT(0)
+#define XXV_RCW1_RX_MASK	BIT(0)
+#define XXV_RCW1_FCS_MASK	BIT(1)
+#define XXV_TC_FCS_MASK		BIT(1)
+#define XXV_MIN_JUM_MASK	GENMASK(7, 0)
+#define XXV_MAX_JUM_MASK	GENMASK(10, 8)
+#define XXV_RX_BLKLCK_MASK	BIT(0)
+#define XXV_TICKREG_STATEN_MASK BIT(0)
+#define XXV_MAC_MIN_PKT_LEN	64
+#define XXV_GTWIZ_RESET_DONE	(BIT(0) | BIT(1))
+#define XXV_MAJ_MASK		GENMASK(7, 0)
+#define XXV_MIN_MASK		GENMASK(15, 8)
+
+/* USXGMII Register Mask Definitions  */
+#define USXGMII_AN_EN		BIT(5)
+#define USXGMII_AN_RESET	BIT(6)
+#define USXGMII_AN_RESTART	BIT(7)
+#define USXGMII_EN		BIT(16)
+#define USXGMII_RATE_MASK	0x0E000700
+#define USXGMII_RATE_1G		0x04000200
+#define USXGMII_RATE_2G5	0x08000400
+#define USXGMII_RATE_10M	0x0
+#define USXGMII_RATE_100M	0x02000100
+#define USXGMII_RATE_5G		0x0A000500
+#define USXGMII_RATE_10G	0x06000300
+#define USXGMII_FD		BIT(28)
+#define USXGMII_LINK_STS	BIT(31)
+
+/* USXGMII AN STS register mask definitions */
+#define USXGMII_AN_STS_COMP_MASK	BIT(16)
+
+/* MCDMA Register Definitions */
+#define XMCDMA_CR_OFFSET	0x00
+#define XMCDMA_SR_OFFSET	0x04
+#define XMCDMA_CHEN_OFFSET	0x08
+#define XMCDMA_CHSER_OFFSET	0x0C
+#define XMCDMA_ERR_OFFSET	0x10
+#define XMCDMA_PKTDROP_OFFSET	0x14
+#define XMCDMA_TXWEIGHT0_OFFSET 0x18
+#define XMCDMA_TXWEIGHT1_OFFSET 0x1C
+#define XMCDMA_RXINT_SER_OFFSET 0x20
+#define XMCDMA_TXINT_SER_OFFSET 0x28
+
+#define XMCDMA_CHOBS1_OFFSET	0x440
+#define XMCDMA_CHOBS2_OFFSET	0x444
+#define XMCDMA_CHOBS3_OFFSET	0x448
+#define XMCDMA_CHOBS4_OFFSET	0x44C
+#define XMCDMA_CHOBS5_OFFSET	0x450
+#define XMCDMA_CHOBS6_OFFSET	0x454
+
+#define XMCDMA_CHAN_RX_OFFSET  0x500
+
+/* Per Channel Registers */
+#define XMCDMA_CHAN_CR_OFFSET(chan_id)		(0x40 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_SR_OFFSET(chan_id)		(0x44 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_CURDESC_OFFSET(chan_id)	(0x48 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_TAILDESC_OFFSET(chan_id)	(0x50 + ((chan_id) - 1) * 0x40)
+#define XMCDMA_CHAN_PKTDROP_OFFSET(chan_id)	(0x58 + ((chan_id) - 1) * 0x40)
+
+#define XMCDMA_RX_OFFSET	0x500
+
+/* MCDMA Mask registers */
+#define XMCDMA_CR_RUNSTOP_MASK		BIT(0) /* Start/stop DMA channel */
+#define XMCDMA_CR_RESET_MASK		BIT(2) /* Reset DMA engine */
+
+#define XMCDMA_SR_HALTED_MASK		BIT(0)
+#define XMCDMA_SR_IDLE_MASK		BIT(1)
+
+#define XMCDMA_IRQ_ERRON_OTHERQ_MASK	BIT(3)
+#define XMCDMA_IRQ_PKTDROP_MASK		BIT(4)
+#define XMCDMA_IRQ_IOC_MASK		BIT(5)
+#define XMCDMA_IRQ_DELAY_MASK		BIT(6)
+#define XMCDMA_IRQ_ERR_MASK		BIT(7)
+#define XMCDMA_IRQ_ALL_MASK		GENMASK(7, 5)
+#define XMCDMA_PKTDROP_COALESCE_MASK	GENMASK(15, 8)
+#define XMCDMA_COALESCE_MASK		GENMASK(23, 16)
+#define XMCDMA_DELAY_MASK		GENMASK(31, 24)
+
+#define XMCDMA_CHEN_MASK		GENMASK(7, 0)
+#define XMCDMA_CHID_MASK		GENMASK(7, 0)
+
+#define XMCDMA_ERR_INTERNAL_MASK	BIT(0)
+#define XMCDMA_ERR_SLAVE_MASK		BIT(1)
+#define XMCDMA_ERR_DECODE_MASK		BIT(2)
+#define XMCDMA_ERR_SG_INT_MASK		BIT(4)
+#define XMCDMA_ERR_SG_SLV_MASK		BIT(5)
+#define XMCDMA_ERR_SG_DEC_MASK		BIT(6)
+
+#define XMCDMA_PKTDROP_CNT_MASK		GENMASK(31, 0)
+
+#define XMCDMA_BD_CTRL_TXSOF_MASK	0x80000000 /* First tx packet */
+#define XMCDMA_BD_CTRL_TXEOF_MASK	0x40000000 /* Last tx packet */
+#define XMCDMA_BD_CTRL_ALL_MASK		0xC0000000 /* All control bits */
+#define XMCDMA_BD_STS_ALL_MASK		0xF0000000 /* All status bits */
+#define XMCDMA_BD_SD_STS_ALL_MASK	0x00000030 /* TUSER input port bits */
+
+#define XMCDMA_BD_SD_STS_TUSER_EP	0x00000000
+#define XMCDMA_BD_SD_STS_TUSER_MAC_1	0x00000010
+#define XMCDMA_BD_SD_STS_TUSER_MAC_2	0x00000020
+#define XMCDMA_BD_SD_STS_TUSER_EX_EP	0x00000030
+
+#define XMCDMA_COALESCE_SHIFT		16
+#define XMCDMA_DELAY_SHIFT		24
+#define XMCDMA_DFT_TX_THRESHOLD		1
+
+#define XMCDMA_TXWEIGHT_CH_MASK(chan_id)	GENMASK(((chan_id) * 4 + 3), \
+							(chan_id) * 4)
+#define XMCDMA_TXWEIGHT_CH_SHIFT(chan_id)	((chan_id) * 4)
+
+/* PTP Packet length */
+#define XAE_TX_PTP_LEN		16
+#define XXV_TX_PTP_LEN		12
+
+/* Macros used when AXI DMA h/w is configured without DRE */
+#define XAE_TX_BUFFERS		64
+#define XAE_MAX_PKT_LEN		8192
+
+/* MRMAC Register Definitions */
+/* Configuration Registers */
+#define MRMAC_REV_OFFSET		0x00000000
+#define MRMAC_RESET_OFFSET		0x00000004
+#define MRMAC_MODE_OFFSET		0x00000008
+#define MRMAC_CONFIG_TX_OFFSET		0x0000000C
+#define MRMAC_CONFIG_RX_OFFSET		0x00000010
+#define MRMAC_TICK_OFFSET		0x0000002C
+#define MRMAC_CFG1588_OFFSET	0x00000040
+
+/* Status Registers */
+#define MRMAC_TX_STS_OFFSET		0x00000740
+#define MRMAC_RX_STS_OFFSET		0x00000744
+#define MRMAC_TX_RT_STS_OFFSET		0x00000748
+#define MRMAC_RX_RT_STS_OFFSET		0x0000074C
+#define MRMAC_STATRX_BLKLCK_OFFSET	0x00000754
+#define MRMAC_STATRX_VALID_CTRL_OFFSET	0x000007B8
+
+/* Register bit masks */
+#define MRMAC_RX_SERDES_RST_MASK	(BIT(3) | BIT(2) | BIT(1) | BIT(0))
+#define MRMAC_TX_SERDES_RST_MASK	BIT(4)
+#define MRMAC_RX_RST_MASK		BIT(5)
+#define MRMAC_TX_RST_MASK		BIT(6)
+#define MRMAC_RX_AXI_RST_MASK		BIT(8)
+#define MRMAC_TX_AXI_RST_MASK		BIT(9)
+#define MRMAC_STS_ALL_MASK		0xFFFFFFFF
+
+#define MRMAC_RX_EN_MASK		BIT(0)
+#define MRMAC_RX_DEL_FCS_MASK		BIT(1)
+
+#define MRMAC_TX_EN_MASK		BIT(0)
+#define MRMAC_TX_INS_FCS_MASK		BIT(1)
+
+#define MRMAC_RX_BLKLCK_MASK		BIT(0)
+#define MRMAC_RX_STATUS_MASK		BIT(0)
+#define MRMAC_RX_VALID_MASK		BIT(0)
+
+#define MRMAC_CTL_DATA_RATE_MASK	GENMASK(2, 0)
+#define MRMAC_CTL_DATA_RATE_10G		0
+#define MRMAC_CTL_DATA_RATE_25G		1
+#define MRMAC_CTL_DATA_RATE_40G		2
+#define MRMAC_CTL_DATA_RATE_50G		3
+#define MRMAC_CTL_DATA_RATE_100G	4
+
+#define MRMAC_CTL_AXIS_CFG_MASK		GENMASK(11, 9)
+#define MRMAC_CTL_AXIS_CFG_SHIFT	9
+#define MRMAC_CTL_AXIS_CFG_10G_IND	1
+#define MRMAC_CTL_AXIS_CFG_25G_IND	1
+
+#define MRMAC_CTL_SERDES_WIDTH_MASK	GENMASK(6, 4)
+#define MRMAC_CTL_SERDES_WIDTH_SHIFT	4
+#define MRMAC_CTL_SERDES_WIDTH_10G	4
+#define MRMAC_CTL_SERDES_WIDTH_25G	6
+
+#define MRMAC_CTL_RATE_CFG_MASK		(MRMAC_CTL_DATA_RATE_MASK |	\
+					 MRMAC_CTL_AXIS_CFG_MASK |	\
+					 MRMAC_CTL_SERDES_WIDTH_MASK)
+
+#define MRMAC_CTL_PM_TICK_MASK		BIT(30)
+#define MRMAC_TICK_TRIGGER		BIT(0)
+#define MRMAC_ONE_STEP_EN		BIT(0)
+
+/* MRMAC GT wrapper registers */
+#define MRMAC_GT_PLL_OFFSET		0x0
+#define MRMAC_GT_PLL_STS_OFFSET		0x8
+#define MRMAC_GT_RATE_OFFSET		0x0
+#define MRMAC_GT_CTRL_OFFSET		0x8
+
+#define MRMAC_GT_PLL_RST_MASK		0x00030003
+#define MRMAC_GT_PLL_DONE_MASK		0xFF
+#define MRMAC_GT_RST_ALL_MASK		BIT(0)
+#define MRMAC_GT_RST_RX_MASK		BIT(1)
+#define MRMAC_GT_RST_TX_MASK		BIT(2)
+#define MRMAC_GT_10G_MASK		0x00000001
+#define MRMAC_GT_25G_MASK		0x00000002
+
+#define MRMAC_GT_LANE_OFFSET		BIT(16)
+#define MRMAC_MAX_GT_LANES		4
+/**
+ * struct axidma_bd - Axi Dma buffer descriptor layout
+ * @next:         MM2S/S2MM Next Descriptor Pointer
+ * @reserved1:    Reserved and not used for 32-bit
+ * @phys:         MM2S/S2MM Buffer Address
+ * @reserved2:    Reserved and not used for 32-bit
+ * @reserved3:    Reserved and not used
+ * @reserved4:    Reserved and not used
+ * @cntrl:        MM2S/S2MM Control value
+ * @status:       MM2S/S2MM Status value
+ * @app0:         MM2S/S2MM User Application Field 0.
+ * @app1:         MM2S/S2MM User Application Field 1.
+ * @app2:         MM2S/S2MM User Application Field 2.
+ * @app3:         MM2S/S2MM User Application Field 3.
+ * @app4:         MM2S/S2MM User Application Field 4.
+ * @sw_id_offset: MM2S/S2MM Sw ID
+ * @ptp_tx_skb:   If timestamping is enabled used for timestamping skb
+ *		  Otherwise reserved.
+ * @ptp_tx_ts_tag: Tag value of 2 step timestamping if timestamping is enabled
+ *		   Otherwise reserved.
+ * @tx_skb:	  Transmit skb address
+ * @tx_desc_mapping: Tx Descriptor DMA mapping type.
+ */
+struct axidma_bd {
+	phys_addr_t next;	/* Physical address of next buffer descriptor */
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved1;
+#endif
+	phys_addr_t phys;
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved2;
+#endif
+	u32 reserved3;
+	u32 reserved4;
+	u32 cntrl;
+	u32 status;
+	u32 app0;
+	u32 app1;	/* TX start << 16 | insert */
+	u32 app2;	/* TX csum seed */
+	u32 app3;
+	u32 app4;
+	phys_addr_t sw_id_offset; /* first unused field by h/w */
+	phys_addr_t ptp_tx_skb;
+	u32 ptp_tx_ts_tag;
+	phys_addr_t tx_skb;
+	u32 tx_desc_mapping;
+} __aligned(XAXIDMA_BD_MINIMUM_ALIGNMENT);
+/**
+ * struct aximcdma_bd - Axi MCDMA buffer descriptor layout
+ * @next:         MM2S/S2MM Next Descriptor Pointer
+ * @reserved1:    Reserved and not used for 32-bit
+ * @phys:         MM2S/S2MM Buffer Address
+ * @reserved2:    Reserved and not used for 32-bit
+ * @reserved3:    Reserved and not used
+ * @cntrl:        MM2S/S2MM Control value
+ * @status:       S2MM Status value
+ * @sband_stats:  S2MM Sideband Status value
+ *		  MM2S Status value
+ * @app0:         MM2S/S2MM User Application Field 0.
+ * @app1:         MM2S/S2MM User Application Field 1.
+ * @app2:         MM2S/S2MM User Application Field 2.
+ * @app3:         MM2S/S2MM User Application Field 3.
+ * @app4:         MM2S/S2MM User Application Field 4.
+ * @sw_id_offset: MM2S/S2MM Sw ID
+ * @ptp_tx_skb:   If timestamping is enabled used for timestamping skb
+ *		  Otherwise reserved.
+ * @ptp_tx_ts_tag: Tag value of 2 step timestamping if timestamping is enabled
+ *		   Otherwise reserved.
+ * @tx_skb:	  Transmit skb address
+ * @tx_desc_mapping: Tx Descriptor DMA mapping type.
+ */
+struct aximcdma_bd {
+	phys_addr_t next;	/* Physical address of next buffer descriptor */
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved1;
+#endif
+	phys_addr_t phys;
+#ifndef CONFIG_PHYS_ADDR_T_64BIT
+	u32 reserved2;
+#endif
+	u32 reserved3;
+	u32 cntrl;
+	u32 status;
+	u32 sband_stats;
+	u32 app0;
+	u32 app1;	/* TX start << 16 | insert */
+	u32 app2;	/* TX csum seed */
+	u32 app3;
+	u32 app4;
+	phys_addr_t sw_id_offset; /* first unused field by h/w */
+	phys_addr_t ptp_tx_skb;
+	u32 ptp_tx_ts_tag;
+	phys_addr_t tx_skb;
+	u32 tx_desc_mapping;
+} __aligned(XAXIDMA_BD_MINIMUM_ALIGNMENT);
+
+#define XAE_NUM_MISC_CLOCKS 3
+#define DESC_DMA_MAP_SINGLE 0
+#define DESC_DMA_MAP_PAGE 1
+
+#define XAE_MAX_QUEUES		7
+
+/* TSN queues range is 2 to 5. For eg: for num_tc = 2 minimum queues = 2;
+ * for num_tc = 3 with sideband signalling maximum queues = 5
+ */
+#define XAE_MAX_TSN_TC		3
+#define XAE_TSN_MIN_QUEUES	4
+
+#define TSN_BRIDGEEP_EPONLY	BIT(29)
+
+#ifdef CONFIG_AXIENET_HAS_TADMA
+#define TADMA_MAX_NO_STREAM	128
+struct axitadma_bd {
+	u32 phys;
+	phys_addr_t tx_skb;
+	u32 tx_desc_mapping;
+	u32 num_frag;
+	u32 len;
+};
+#endif
+
+enum axienet_tsn_ioctl {
+	SIOCCHIOCTL = SIOCDEVPRIVATE,
+	SIOC_GET_SCHED,
+	SIOC_PREEMPTION_CFG,
+	SIOC_PREEMPTION_CTRL,
+	SIOC_PREEMPTION_STS,
+	SIOC_PREEMPTION_COUNTER,
+	SIOC_QBU_USER_OVERRIDE,
+	SIOC_QBU_STS,
+	SIOC_TADMA_STR_ADD,
+	SIOC_TADMA_PROG_ALL,
+	SIOC_TADMA_STR_FLUSH,
+	SIOC_PREEMPTION_RECEIVE,
+	SIOC_TADMA_OFF,
+};
+
+/**
+ * struct axienet_local - axienet private per device data
+ * @ndev:	Pointer for net_device to which it will be attached.
+ * @dev:	Pointer to device structure
+ * @phy_node:	Pointer to device node structure
+ * @axi_clk:	AXI4-Lite bus clock
+ * @misc_clks:	Misc ethernet clocks (AXI4-Stream, Ref, MGT clocks)
+ * @mii_bus:	Pointer to MII bus structure
+ * @mii_clk_div: MII bus clock divider value
+ * @regs_start: Resource start for axienet device addresses
+ * @regs:	Base address for the axienet_local device address space
+ * @mcdma_regs:	Base address for the aximcdma device address space
+ * @napi:	Napi Structure array for all dma queues
+ * @num_tx_queues: Total number of Tx DMA queues
+ * @num_rx_queues: Total number of Rx DMA queues
+ * @dq:		DMA queues data
+ * @phy_mode:	Phy type to identify between MII/GMII/RGMII/SGMII/1000 Base-X
+ * @num_tc:	Total number of TSN Traffic classes
+ * @abl_reg:	TSN abilities register
+ * @st_pcp:     pcp values mapped to scheduled traffic.
+ * @res_pcp:    pcp values mapped to reserved traffic.
+ * @master:	Master endpoint
+ * @slaves:	Front panel ports
+ * @ex_ep:	extended end point
+ * @packet_switch: packet switching parameter
+ * @switch_prt: Switch port number
+ * @timer_priv: PTP timer private data pointer
+ * @ptp_tx_irq: PTP tx irq
+ * @ptp_rx_irq: PTP rx irq
+ * @rtc_irq:	PTP RTC irq
+ * @qbv_irq:	QBV shed irq
+ * @ptp_ts_type: ptp time stamp type - 1 or 2 step mode
+ * @ptp_rx_hw_pointer: ptp rx hw pointer
+ * @ptp_rx_sw_pointer: ptp rx sw pointer
+ * @ptp_txq:	PTP tx queue header
+ * @tx_tstamp_work: PTP timestamping work queue
+ * @qbv_regs:	pointer to qbv registers base address
+ * @tadma_regs: pointer to tadma registers base address
+ * @tadma_irq: TADMA IRQ number
+ * @t_cb: pointer to tadma_cb
+ * @active_sfm: current active stream fetch memory
+ * @num_tadma_buffers: number of TADMA buffers per stream
+ * @num_streams: maximum number of streams TADMA can fetch
+ * @num_entries: maximum number of entries in TADMA streams config
+ * @tx_bd: tadma transmit buffer descriptor
+ * @tx_bd_head: transmit BD head indices
+ * @tx_bd_tail: transmit BD tail indices
+ * @tx_bd_rd: TADMA read pointer offset
+ * @tadma_tx_lock: TADMA tx lock
+ * @ptp_tx_lock: PTP tx lock
+ * @dma_err_tasklet: Tasklet structure to process Axi DMA errors
+ * @eth_irq:	Axi Ethernet IRQ number
+ * @options:	AxiEthernet option word
+ * @last_link:	Phy link state in which the PHY was negotiated earlier
+ * @features:	Stores the extended features supported by the axienet hw
+ * @tx_bd_num:	Number of TX buffer descriptors.
+ * @rx_bd_num:	Number of RX buffer descriptors.
+ * @max_frm_size: Stores the maximum size of the frame that can be that
+ *		  Txed/Rxed in the existing hardware. If jumbo option is
+ *		  supported, the maximum frame size would be 9k. Else it is
+ *		  1522 bytes (assuming support for basic VLAN)
+ * @rxmem:	Stores rx memory size for jumbo frame handling.
+ * @csum_offload_on_tx_path:	Stores the checksum selection on TX side.
+ * @csum_offload_on_rx_path:	Stores the checksum selection on RX side.
+ * @coalesce_count_rx:	Store the irq coalesce on RX side.
+ * @coalesce_count_tx:	Store the irq coalesce on TX side.
+ * @phy_flags:	Phy interface flags.
+ * @eth_hasnobuf: Ethernet is configured in Non buf mode.
+ * @eth_hasptp: Ethernet is configured for ptp.
+ * @axienet_config: Ethernet config structure
+ * @tx_ts_regs:	  Base address for the axififo device address space.
+ * @rx_ts_regs:	  Base address for the rx axififo device address space.
+ * @tstamp_config: Hardware timestamp config structure.
+ * @current_rx_filter : Current rx filter.
+ * @tx_ptpheader: Stores the tx ptp header.
+ * @aclk: AXI4-Lite clock for ethernet and dma.
+ * @eth_sclk: AXI4-Stream interface clock.
+ * @eth_refclk: Stable clock used by signal delay primitives and transceivers.
+ * @eth_dclk: Dynamic Reconfiguration Port(DRP) clock.
+ * @dma_sg_clk: DMA Scatter Gather Clock.
+ * @dma_rx_clk: DMA S2MM Primary Clock.
+ * @dma_tx_clk: DMA MM2S Primary Clock.
+ * @qnum:     Axi Ethernet queue number to be operate on.
+ * @chan_num: MCDMA Channel number to be operate on.
+ * @chan_id:  MCMDA Channel id used in conjunction with weight parameter.
+ * @weight:   MCDMA Channel weight value to be configured for.
+ * @dma_mask: Specify the width of the DMA address space.
+ * @usxgmii_rate: USXGMII PHY speed.
+ * @mrmac_rate: MRMAC speed.
+ * @gt_pll: Common GT PLL mask control register space.
+ * @gt_ctrl: GT speed and reset control register space.
+ * @phc_index: Index to corresponding PTP clock used.
+ * @gt_lane: MRMAC GT lane index used.
+ * @ptp_os_cf: CF TS of PTP PDelay req for one step usage.
+ * @xxv_ip_version: XXV IP version
+ */
+struct axienet_local {
+	struct net_device *ndev;
+	struct device *dev;
+
+	struct device_node *phy_node;
+
+	struct clk *axi_clk;
+	struct clk_bulk_data misc_clks[XAE_NUM_MISC_CLOCKS];
+
+	struct mii_bus *mii_bus;
+	u8 mii_clk_div;
+
+	resource_size_t regs_start;
+	void __iomem *regs;
+	void __iomem *mcdma_regs;
+
+	struct tasklet_struct dma_err_tasklet[XAE_MAX_QUEUES];
+	struct napi_struct napi[XAE_MAX_QUEUES];	/* NAPI Structure */
+
+	u16    num_tx_queues;	/* Number of TX DMA queues */
+	u16    num_rx_queues;	/* Number of RX DMA queues */
+	struct axienet_dma_q *dq[XAE_MAX_QUEUES];	/* DMA queue data*/
+
+	phy_interface_t phy_mode;
+
+	u16   num_tc;
+	u32   abl_reg;
+	u8    st_pcp;
+	u8    res_pcp;
+	struct net_device *master; /* master endpoint */
+	struct net_device *slaves[2]; /* two front panel ports */
+	struct net_device *ex_ep; /* extended endpoint*/
+	u8	packet_switch;
+	u8      switch_prt;	/* port on the switch */
+#ifdef CONFIG_XILINX_TSN_PTP
+	void *timer_priv;
+	int ptp_tx_irq;
+	int ptp_rx_irq;
+	int rtc_irq;
+	int qbv_irq;
+	int ptp_ts_type;
+	u8  ptp_rx_hw_pointer;
+	u8  ptp_rx_sw_pointer;
+	struct sk_buff_head ptp_txq;
+	struct work_struct tx_tstamp_work;
+#endif
+#ifdef CONFIG_XILINX_TSN_QBV
+	void __iomem *qbv_regs;
+#endif
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	void __iomem *tadma_regs;
+	int tadma_irq;
+	void *t_cb;
+	int active_sfm;
+	int num_tadma_buffers;
+	int num_streams;
+	int num_entries;
+	struct axitadma_bd **tx_bd;
+	u32 tx_bd_head[TADMA_MAX_NO_STREAM];
+	u32 tx_bd_tail[TADMA_MAX_NO_STREAM];
+	u32 tx_bd_rd[TADMA_MAX_NO_STREAM];
+	spinlock_t tadma_tx_lock;               /* TSN TADMA tx lock*/
+#endif
+	spinlock_t ptp_tx_lock;		/* PTP tx lock*/
+	int eth_irq;
+
+	u32 options;			/* Current options word */
+	u32 last_link;
+	u32 features;
+
+	u16 tx_bd_num;
+	u32 rx_bd_num;
+
+	u32 max_frm_size;
+	u32 rxmem;
+
+	int csum_offload_on_tx_path;
+	int csum_offload_on_rx_path;
+
+	u32 coalesce_count_rx;
+	u32 coalesce_count_tx;
+	u32 phy_flags;
+	bool eth_hasnobuf;
+	bool eth_hasptp;
+	const struct axienet_config *axienet_config;
+
+#if defined(CONFIG_XILINX_TSN_PTP)
+	void __iomem *tx_ts_regs;
+	void __iomem *rx_ts_regs;
+	struct hwtstamp_config tstamp_config;
+	int current_rx_filter;
+	u8 *tx_ptpheader;
+#endif
+	struct clk *aclk;
+	struct clk *eth_sclk;
+	struct clk *eth_refclk;
+	struct clk *eth_dclk;
+	struct clk *dma_sg_clk;
+	struct clk *dma_rx_clk;
+	struct clk *dma_tx_clk;
+
+	/* MCDMA Fields */
+	int qnum[XAE_MAX_QUEUES];
+	int chan_num[XAE_MAX_QUEUES];
+	/* WRR Fields */
+	u16 chan_id;
+	u16 weight;
+
+	u8 dma_mask;
+	u32 usxgmii_rate;
+
+	u32 mrmac_rate;		/* MRMAC speed */
+	void __iomem *gt_pll;	/* Common GT PLL mask control register space */
+	void __iomem *gt_ctrl;	/* GT speed and reset control register space */
+	u32 phc_index;		/* Index to corresponding PTP clock used  */
+	u32 gt_lane;		/* MRMAC GT lane index used */
+	u64 ptp_os_cf;		/* CF TS of PTP PDelay req for one step usage */
+	u32 xxv_ip_version;
+};
+
+/**
+ * struct axienet_dma_q - axienet private per dma queue data
+ * @lp:		Parent pointer
+ * @dma_regs:	Base address for the axidma device address space
+ * @tx_irq:	Axidma TX IRQ number
+ * @rx_irq:	Axidma RX IRQ number
+ * @tx_lock:	Spin lock for tx path
+ * @rx_lock:	Spin lock for tx path
+ * @tx_bd_v:	Virtual address of the TX buffer descriptor ring
+ * @tx_bd_p:	Physical address(start address) of the TX buffer descr. ring
+ * @rx_bd_v:	Virtual address of the RX buffer descriptor ring
+ * @rx_bd_p:	Physical address(start address) of the RX buffer descr. ring
+ * @tx_buf:	Virtual address of the Tx buffer pool used by the driver when
+ *		DMA h/w is configured without DRE.
+ * @tx_bufs:	Virutal address of the Tx buffer address.
+ * @tx_bufs_dma: Physical address of the Tx buffer address used by the driver
+ *		 when DMA h/w is configured without DRE.
+ * @eth_hasdre: Tells whether DMA h/w is configured with dre or not.
+ * @tx_bd_ci:	Stores the index of the Tx buffer descriptor in the ring being
+ *		accessed currently. Used while alloc. BDs before a TX starts
+ * @tx_bd_tail:	Stores the index of the Tx buffer descriptor in the ring being
+ *		accessed currently. Used while processing BDs after the TX
+ *		completed.
+ * @rx_bd_ci:	Stores the index of the Rx buffer descriptor in the ring being
+ *		accessed currently.
+ * @flags:      MCDMA management channel flags
+ * @chan_id:    MCDMA channel to operate on.
+ * @rx_offset:	MCDMA S2MM channel starting offset.
+ * @txq_bd_v:	Virtual address of the MCDMA TX buffer descriptor ring
+ * @rxq_bd_v:	Virtual address of the MCDMA RX buffer descriptor ring
+ * @tx_packets: Number of transmit packets processed by the dma queue.
+ * @tx_bytes:   Number of transmit bytes processed by the dma queue.
+ * @rx_packets: Number of receive packets processed by the dma queue.
+ * @rx_bytes:	Number of receive bytes processed by the dma queue.
+ */
+struct axienet_dma_q {
+	struct axienet_local	*lp; /* parent */
+	void __iomem *dma_regs;
+
+	int tx_irq;
+	int rx_irq;
+
+	spinlock_t tx_lock;		/* tx lock */
+	spinlock_t rx_lock;		/* rx lock */
+
+	/* Buffer descriptors */
+	struct axidma_bd *tx_bd_v;
+	struct axidma_bd *rx_bd_v;
+	dma_addr_t rx_bd_p;
+	dma_addr_t tx_bd_p;
+
+	unsigned char *tx_buf[XAE_TX_BUFFERS];
+	unsigned char *tx_bufs;
+	dma_addr_t tx_bufs_dma;
+	bool eth_hasdre;
+
+	u32 tx_bd_ci;
+	u32 rx_bd_ci;
+	u32 tx_bd_tail;
+
+	/* MCDMA fields */
+#ifdef CONFIG_XILINX_TSN
+#define MCDMA_MGMT_CHAN		BIT(0)
+#define MCDMA_EP_EX_CHAN	BIT(1)
+	u32 flags;
+#endif
+	u16 chan_id;
+	u32 rx_offset;
+	struct aximcdma_bd *txq_bd_v;
+	struct aximcdma_bd *rxq_bd_v;
+
+	unsigned long tx_packets;
+	unsigned long tx_bytes;
+	unsigned long rx_packets;
+	unsigned long rx_bytes;
+};
+
+#define AXIENET_ETHTOOLS_SSTATS_LEN 6
+#define AXIENET_TX_SSTATS_LEN(lp) ((lp)->num_tx_queues * 2)
+#define AXIENET_RX_SSTATS_LEN(lp) ((lp)->num_rx_queues * 2)
+
+/**
+ * enum axienet_ip_type - AXIENET IP/MAC type.
+ *
+ * @XAXIENET_1G:	 IP is 1G MAC
+ * @XAXIENET_2_5G:	 IP type is 2.5G MAC.
+ * @XAXIENET_LEGACY_10G: IP type is legacy 10G MAC.
+ * @XAXIENET_10G_25G:	 IP type is 10G/25G MAC(XXV MAC).
+ * @XAXIENET_MRMAC:	 IP type is hardened Multi Rate MAC (MRMAC).
+ *
+ */
+enum axienet_ip_type {
+	XAXIENET_1G = 0,
+	XAXIENET_2_5G,
+	XAXIENET_LEGACY_10G,
+	XAXIENET_10G_25G,
+	XAXIENET_MRMAC,
+};
+
+struct axienet_config {
+	enum axienet_ip_type mactype;
+	void (*setoptions)(struct net_device *ndev, u32 options);
+	int (*clk_init)(struct platform_device *pdev, struct clk **axi_aclk,
+			struct clk **axis_clk, struct clk **ref_clk,
+			struct clk **dclk);
+	u32 tx_ptplen;
+	u8 ts_header_len;
+};
+
+/**
+ * struct axienet_option - Used to set axi ethernet hardware options
+ * @opt:	Option to be set.
+ * @reg:	Register offset to be written for setting the option
+ * @m_or:	Mask to be ORed for setting the option in the register
+ */
+struct axienet_option {
+	u32 opt;
+	u32 reg;
+	u32 m_or;
+};
+
+struct xxvenet_option {
+	u32 opt;
+	u32 reg;
+	u32 m_or;
+};
+
+extern void __iomem *mrmac_gt_pll;
+extern void __iomem *mrmac_gt_ctrl;
+extern int mrmac_pll_reg;
+extern int mrmac_pll_rst;
+
+/**
+ * axienet_ior - Memory mapped Axi Ethernet register read
+ * @lp:         Pointer to axienet local structure
+ * @offset:     Address offset from the base address of Axi Ethernet core
+ *
+ * Return: The contents of the Axi Ethernet register
+ *
+ * This function returns the contents of the corresponding register.
+ */
+static inline u32 axienet_ior(struct axienet_local *lp, off_t offset)
+{
+	return ioread32(lp->regs + offset);
+}
+
+/**
+ * axienet_ior64 - Memory mapped Axi Ethernet register read from two consecutive registers
+ * @lp:         Pointer to axienet local structure
+ * @offset:     Address offset from the base address of Axi Ethernet core
+ *
+ * Return: 64 bit value, where the LSB 32 bits correspond to the contents of the register
+ * at baseaddress+offset and MSB 32 bits correspond to the contents of the register at
+ * baseaddress+offset+4
+ *
+ * This function returns the 64 bit value corresponding to two consecutive registers.
+ */
+static inline u64 axienet_ior64(struct axienet_local *lp, off_t offset)
+{
+	return ioread64_lo_hi(lp->regs + offset);
+}
+
+static inline u32 axinet_ior_read_mcr(struct axienet_local *lp)
+{
+	return axienet_ior(lp, XAE_MDIO_MCR_OFFSET);
+}
+
+/**
+ * axienet_iow - Memory mapped Axi Ethernet register write
+ * @lp:         Pointer to axienet local structure
+ * @offset:     Address offset from the base address of Axi Ethernet core
+ * @value:      Value to be written into the Axi Ethernet register
+ *
+ * This function writes the desired value into the corresponding Axi Ethernet
+ * register.
+ */
+static inline void axienet_iow(struct axienet_local *lp, off_t offset,
+			       u32 value)
+{
+	iowrite32(value, lp->regs + offset);
+}
+
+/**
+ * axienet_get_mrmac_blocklock - Write to Clear MRMAC RX block lock status register
+ * and read the latest status
+ * @lp:         Pointer to axienet local structure
+ *
+ * Return: The contents of the Contents of MRMAC RX block lock status register
+ */
+
+static inline u32 axienet_get_mrmac_blocklock(struct axienet_local *lp)
+{
+	axienet_iow(lp, MRMAC_STATRX_BLKLCK_OFFSET, MRMAC_STS_ALL_MASK);
+	return axienet_ior(lp, MRMAC_STATRX_BLKLCK_OFFSET);
+}
+
+/**
+ * axienet_get_mrmac_rx_status - Write to Clear MRMAC RX status register
+ * and read the latest status
+ * @lp:		Pointer to axienet local structure
+ *
+ * Return: The contents of the Contents of MRMAC RX status register
+ */
+
+static inline u32 axienet_get_mrmac_rx_status(struct axienet_local *lp)
+{
+	axienet_iow(lp, MRMAC_RX_STS_OFFSET, MRMAC_STS_ALL_MASK);
+	return axienet_ior(lp, MRMAC_RX_STS_OFFSET);
+}
+
+/**
+ * axienet_dma_in32 - Memory mapped Axi DMA register read
+ * @q:		Pointer to DMA queue structure
+ * @reg:	Address offset from the base address of the Axi DMA core
+ *
+ * Return: The contents of the Axi DMA register
+ *
+ * This function returns the contents of the corresponding Axi DMA register.
+ */
+static inline u32 axienet_dma_in32(struct axienet_dma_q *q, off_t reg)
+{
+	return ioread32(q->dma_regs + reg);
+}
+
+/**
+ * axienet_dma_out32 - Memory mapped Axi DMA register write.
+ * @q:		Pointer to DMA queue structure
+ * @reg:	Address offset from the base address of the Axi DMA core
+ * @value:	Value to be written into the Axi DMA register
+ *
+ * This function writes the desired value into the corresponding Axi DMA
+ * register.
+ */
+static inline void axienet_dma_out32(struct axienet_dma_q *q,
+				     off_t reg, u32 value)
+{
+	iowrite32(value, q->dma_regs + reg);
+}
+
+/**
+ * axienet_dma_bdout - Memory mapped Axi DMA register Buffer Descriptor write.
+ * @q:		Pointer to DMA queue structure
+ * @reg:	Address offset from the base address of the Axi DMA core
+ * @value:	Value to be written into the Axi DMA register
+ *
+ * This function writes the desired value into the corresponding Axi DMA
+ * register.
+ */
+static inline void axienet_dma_bdout(struct axienet_dma_q *q,
+				     off_t reg, dma_addr_t value)
+{
+#if defined(CONFIG_PHYS_ADDR_T_64BIT)
+	writeq(value, (q->dma_regs + reg));
+#else
+	writel(value, (q->dma_regs + reg));
+#endif
+}
+
+#ifdef CONFIG_XILINX_TSN_QBV
+/**
+ * axienet_qbv_ior - Memory mapped TSN QBV register read
+ * @lp:         Pointer to axienet local structure
+ * @offset:     Address offset from the base address of Axi Ethernet core
+ *
+ * Return: The contents of the Axi Ethernet register
+ *
+ * This function returns the contents of the corresponding register.
+ */
+static inline u32 axienet_qbv_ior(struct axienet_local *lp, off_t offset)
+{
+	return ioread32(lp->qbv_regs + offset);
+}
+
+/**
+ * axienet_qbv_iow - Memory mapped TSN QBV register write
+ * @lp:         Pointer to axienet local structure
+ * @offset:     Address offset from the base address of Axi Ethernet core
+ * @value:      Value to be written into the Axi Ethernet register
+ *
+ * This function writes the desired value into the corresponding Axi Ethernet
+ * register.
+ */
+static inline void axienet_qbv_iow(struct axienet_local *lp, off_t offset,
+				   u32 value)
+{
+	iowrite32(value, (lp->qbv_regs + offset));
+}
+#endif
+
+/* Function prototypes visible in xilinx_axienet_mdio.c for other files */
+int axienet_mdio_enable(struct axienet_local *lp);
+void axienet_mdio_disable(struct axienet_local *lp);
+int axienet_mdio_setup(struct axienet_local *lp);
+void axienet_mdio_teardown(struct axienet_local *lp);
+void axienet_adjust_link_tsn(struct net_device *ndev);
+int axienet_tsn_open(struct net_device *ndev);
+int axienet_tsn_stop(struct net_device *ndev);
+int axienet_tsn_probe(struct platform_device *pdev,
+		      struct axienet_local *lp,
+		      struct net_device *ndev);
+int tsn_mcdma_probe(struct platform_device *pdev, struct axienet_local *lp,
+		    struct net_device *ndev);
+int axienet_tsn_xmit(struct sk_buff *skb, struct net_device *ndev);
+u16 axienet_tsn_select_queue(struct net_device *ndev, struct sk_buff *skb,
+			     struct net_device *sb_dev);
+u16 axienet_tsn_pcp_to_queue(struct net_device *ndev, struct sk_buff *skb);
+int axienet_get_pcp_mask(struct axienet_local *lp, u16 num_tc);
+int tsn_data_path_open(struct net_device *ndev);
+int tsn_data_path_close(struct net_device *ndev);
+#ifdef CONFIG_XILINX_TSN_PTP
+void *axienet_ptp_timer_probe(void __iomem *base, struct platform_device *pdev);
+void axienet_tx_tstamp(struct work_struct *work);
+int axienet_ptp_timer_remove(void *priv);
+#endif
+#ifdef CONFIG_XILINX_TSN_QBV
+int axienet_qbv_init(struct net_device *ndev);
+void axienet_qbv_remove(struct net_device *ndev);
+int axienet_set_schedule(struct net_device *ndev, void __user *useraddr);
+int axienet_get_schedule(struct net_device *ndev, void __user *useraddr);
+#endif
+
+#ifdef CONFIG_XILINX_TSN_QBR
+int axienet_preemption(struct net_device *ndev, void __user *useraddr);
+int axienet_preemption_ctrl(struct net_device *ndev, void __user *useraddr);
+int axienet_preemption_sts(struct net_device *ndev, void __user *useraddr);
+int axienet_preemption_receive(struct net_device *ndev);
+int axienet_preemption_cnt(struct net_device *ndev, void __user *useraddr);
+int axienet_preemption_sts_ethtool(struct net_device *ndev, struct ethtool_mm_state *state);
+void axienet_preemption_cnt_ethtool(struct net_device *ndev, struct ethtool_mm_stats *stats);
+int axienet_preemption_ctrl_ethtool(struct net_device *ndev, struct ethtool_mm_cfg *config_data,
+				    struct netlink_ext_ack *extack);
+#ifdef CONFIG_XILINX_TSN_QBV
+int axienet_qbu_user_override(struct net_device *ndev, void __user *useraddr);
+int axienet_qbu_sts(struct net_device *ndev, void __user *useraddr);
+#endif
+#endif
+
+int axienet_mdio_wait_until_ready(struct axienet_local *lp);
+void __maybe_unused axienet_bd_free(struct net_device *ndev,
+				    struct axienet_dma_q *q);
+
+#ifdef CONFIG_AXIENET_HAS_TADMA
+int axienet_tadma_add_stream(struct net_device *ndev, void __user *useraddr);
+int axienet_tadma_flush_stream(struct net_device *ndev, void __user *useraddr);
+int axienet_tadma_off(struct net_device *ndev, void __user *useraddr);
+int axienet_tadma_program(struct net_device *ndev, void __user *useraddr);
+int axienet_tadma_probe(struct platform_device *pdev, struct net_device *ndev);
+int axienet_tadma_xmit(struct sk_buff *skb, struct net_device *ndev, u16 queue_type);
+int axienet_tadma_open(struct net_device *ndev);
+int axienet_tadma_stop(struct net_device *ndev);
+#endif
+
+int __maybe_unused axienet_dma_q_init(struct net_device *ndev,
+				      struct axienet_dma_q *q);
+void axienet_dma_err_handler(unsigned long data);
+irqreturn_t __maybe_unused axienet_tx_irq(int irq, void *_ndev);
+irqreturn_t __maybe_unused axienet_rx_irq(int irq, void *_ndev);
+void axienet_start_xmit_done_tsn(struct net_device *ndev, struct axienet_dma_q *q);
+void axienet_dma_bd_release_tsn(struct net_device *ndev);
+void __axienet_device_reset_tsn(struct axienet_dma_q *q);
+void axienet_set_mac_address_tsn(struct net_device *ndev, const void *address);
+void axienet_set_multicast_list_tsn(struct net_device *ndev);
+int xaxienet_rx_poll_tsn(struct napi_struct *napi, int quota);
+void axienet_setoptions_tsn(struct net_device *ndev, u32 options);
+int axienet_queue_xmit_tsn(struct sk_buff *skb, struct net_device *ndev,
+			   u16 map);
+
+int __maybe_unused axienet_mcdma_rx_q_init_tsn(struct net_device *ndev,
+					       struct axienet_dma_q *q);
+int __maybe_unused axienet_mcdma_tx_q_init_tsn(struct net_device *ndev,
+					       struct axienet_dma_q *q);
+void __maybe_unused axienet_mcdma_tx_bd_free_tsn(struct net_device *ndev,
+						 struct axienet_dma_q *q);
+void __maybe_unused axienet_mcdma_rx_bd_free_tsn(struct net_device *ndev,
+						 struct axienet_dma_q *q);
+irqreturn_t __maybe_unused axienet_mcdma_tx_irq_tsn(int irq, void *_ndev);
+irqreturn_t __maybe_unused axienet_mcdma_rx_irq_tsn(int irq, void *_ndev);
+void __maybe_unused axienet_mcdma_err_handler_tsn(unsigned long data);
+void axienet_strings_tsn(struct net_device *ndev, u32 sset, u8 *data);
+int axienet_sset_count_tsn(struct net_device *ndev, int sset);
+void axienet_get_stats_tsn(struct net_device *ndev,
+			   struct ethtool_stats *stats,
+			   u64 *data);
+int axeinet_mcdma_create_sysfs_tsn(struct kobject *kobj);
+void axeinet_mcdma_remove_sysfs_tsn(struct kobject *kobj);
+int __maybe_unused axienet_mcdma_tx_probe_tsn(struct platform_device *pdev,
+					      struct device_node *np,
+					      struct axienet_local *lp);
+int __maybe_unused axienet_mcdma_rx_probe_tsn(struct platform_device *pdev,
+					      struct device_node *np,
+					      struct net_device *ndev);
+int axienet_ethtools_get_coalesce(struct net_device *ndev,
+				  struct ethtool_coalesce *ecoalesce,
+				  struct kernel_ethtool_coalesce *kernel_coal,
+				  struct netlink_ext_ack *extack);
+int axienet_ethtools_set_coalesce(struct net_device *ndev,
+				  struct ethtool_coalesce *ecoalesce,
+				  struct kernel_ethtool_coalesce *kernel_coal,
+				  struct netlink_ext_ack *extack);
+#if defined(CONFIG_XILINX_TSN_SWITCH)
+int tsn_switch_get_port_parent_id(struct net_device *dev,
+				  struct netdev_phys_item_id *ppid);
+#endif
+
+#endif /* XILINX_AXI_ENET_TSN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_cb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_cb.c
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN QCI Controller module.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#include "xilinx_tsn_switch.h"
+
+#define IN_PORTID_MASK				0x3
+#define IN_PORTID_SHIFT				24
+#define MAX_SEQID_MASK				0x0000FFFF
+#define REMAINING_TICKS_MASK			0x0000FFFF
+
+#define SEQ_REC_HIST_LEN_MASK			0x000000FF
+#define SEQ_REC_HIST_LEN_SHIFT			16
+#define SPLIT_STREAM_INPORTID_SHIFT		12
+#define SPLIT_STREAM_INPORTID_MASK		0x3
+#define SPLIT_STREAM_VLANID_MASK		0x00000FFF
+
+#define GATE_ID_SHIFT				24
+#define MEMBER_ID_SHIFT				8
+#define SEQ_RESET_SHIFT				7
+#define REC_TIMEOUT_SHIFT			6
+#define GATE_STATE_SHIFT			5
+#define FRER_VALID_SHIFT			4
+#define WR_OP_TYPE_SHIFT			2
+#define OP_TYPE_SHIFT				1
+#define WR_OP_TYPE_MASK				0x3
+#define FRER_EN_CONTROL_MASK			0x1
+
+/**
+ * frer_control - Configure thr control for frer
+ * @data:	Value to be programmed
+ */
+void frer_control(struct frer_ctrl data)
+{
+	u32 mask = 0;
+
+	mask = data.gate_id << GATE_ID_SHIFT;
+	mask |= data.memb_id << MEMBER_ID_SHIFT;
+	mask |= data.seq_reset << SEQ_RESET_SHIFT;
+	mask |= data.gate_state << GATE_STATE_SHIFT;
+	mask |= data.rcvry_tmout << REC_TIMEOUT_SHIFT;
+	mask |= data.frer_valid << FRER_VALID_SHIFT;
+	mask |= (data.wr_op_type & WR_OP_TYPE_MASK) << WR_OP_TYPE_SHIFT;
+	mask |= data.op_type << OP_TYPE_SHIFT;
+	mask |= FRER_EN_CONTROL_MASK;
+
+	axienet_iow(&lp, FRER_CONTROL_OFFSET, mask);
+
+	/* wait for write to complete */
+	while ((axienet_ior(&lp, FRER_CONTROL_OFFSET) & FRER_EN_CONTROL_MASK))
+		;
+}
+
+/**
+ * get_ingress_filter_config -  Get Ingress Filter Configuration
+ * @data:	Value returned
+ */
+void get_ingress_filter_config(struct in_fltr *data)
+{
+	u32 reg_val = 0;
+
+	reg_val = axienet_ior(&lp, INGRESS_FILTER_OFFSET);
+
+	data->max_seq_id = reg_val & MAX_SEQID_MASK;
+	data->in_port_id = (reg_val >> IN_PORTID_SHIFT) & IN_PORTID_MASK;
+}
+
+/**
+ * config_ingress_filter -  Configure Ingress Filter Configuration
+ * @data:	Value to be programmed
+ */
+void config_ingress_filter(struct cb data)
+{
+	u32 conf_r1;
+
+	conf_r1 = axienet_ior(&lp, INGRESS_FILTER_OFFSET);
+	conf_r1 &= ~(IN_PORTID_MASK << IN_PORTID_SHIFT);
+	conf_r1 |= ((data.in_fltr_data.in_port_id & IN_PORTID_MASK) <<
+			IN_PORTID_SHIFT);
+	axienet_iow(&lp, INGRESS_FILTER_OFFSET, conf_r1);
+
+	conf_r1 = axienet_ior(&lp, FRER_CONFIG_REG1);
+	conf_r1 &= ~(SEQ_REC_HIST_LEN_MASK << SEQ_REC_HIST_LEN_SHIFT);
+	conf_r1 |= (data.frer_memb_config_data.seq_rec_hist_len &
+			SEQ_REC_HIST_LEN_MASK)
+			<< SEQ_REC_HIST_LEN_SHIFT;
+	axienet_iow(&lp, FRER_CONFIG_REG1, conf_r1);
+	conf_r1 = axienet_ior(&lp, FRER_CONFIG_REG2);
+	conf_r1 &= ~(REMAINING_TICKS_MASK);
+	conf_r1 |= data.frer_memb_config_data.rem_ticks;
+	axienet_iow(&lp, FRER_CONFIG_REG2, conf_r1);
+}
+
+/**
+ * get_member_reg -  Read frer member Configuration registers value
+ * @data:	Value returned
+ */
+void get_member_reg(struct frer_memb_config *data)
+{
+	u32 conf_r1 = 0;
+
+	conf_r1 = axienet_ior(&lp, FRER_CONFIG_REG1);
+	data->rem_ticks = axienet_ior(&lp, FRER_CONFIG_REG2);
+
+	data->seq_rec_hist_len = (conf_r1 >> SEQ_REC_HIST_LEN_SHIFT)
+						& SEQ_REC_HIST_LEN_MASK;
+	data->split_strm_egport_id = (conf_r1 >> SPLIT_STREAM_INPORTID_SHIFT)
+						& SPLIT_STREAM_INPORTID_MASK;
+	data->split_strm_vlan_id = conf_r1 & SPLIT_STREAM_VLANID_MASK;
+}
+
+/**
+ * program_member_reg -  configure frer member Configuration registers
+ * @data:	Value to be programmed
+ */
+void program_member_reg(struct cb data)
+{
+	u32 conf_r1 = 0;
+
+	conf_r1 = axienet_ior(&lp, FRER_CONFIG_REG1);
+	conf_r1 &= ~(SPLIT_STREAM_INPORTID_MASK << SPLIT_STREAM_INPORTID_SHIFT);
+	conf_r1 &= ~(SPLIT_STREAM_VLANID_MASK);
+	conf_r1 |= ((data.frer_memb_config_data.split_strm_egport_id
+					& SPLIT_STREAM_INPORTID_MASK)
+					<< SPLIT_STREAM_INPORTID_SHIFT);
+	conf_r1 |= (data.frer_memb_config_data.split_strm_vlan_id &
+					SPLIT_STREAM_VLANID_MASK);
+
+	axienet_iow(&lp, FRER_CONFIG_REG1, conf_r1);
+	axienet_iow(&lp, FRER_CONFIG_REG2,
+		    data.frer_memb_config_data.rem_ticks);
+
+	conf_r1 = axienet_ior(&lp, INGRESS_FILTER_OFFSET);
+	conf_r1 &= ~MAX_SEQID_MASK;
+	conf_r1 |= (data.in_fltr_data.max_seq_id & MAX_SEQID_MASK);
+	axienet_iow(&lp, INGRESS_FILTER_OFFSET, conf_r1);
+}
+
+/**
+ * get_frer_static_counter -  get frer static counters value
+ * @data:	return value, containing counter value
+ */
+void get_frer_static_counter(struct frer_static_counter *data)
+{
+	int offset = (data->num) * 8;
+
+	data->frer_fr_count.lsb = axienet_ior(&lp, TOTAL_FRER_FRAMES_OFFSET +
+									offset);
+	data->frer_fr_count.msb = axienet_ior(&lp, TOTAL_FRER_FRAMES_OFFSET +
+								offset + 0x4);
+
+	data->disc_frames_in_portid.lsb = axienet_ior(&lp,
+						      FRER_DISCARD_INGS_FLTR_OFFSET + offset);
+	data->disc_frames_in_portid.msb = axienet_ior(&lp,
+						      FRER_DISCARD_INGS_FLTR_OFFSET + offset + 0x4);
+
+	data->pass_frames_ind_recv.lsb = axienet_ior(&lp,
+						     FRER_PASS_FRAMES_INDV_OFFSET + offset);
+	data->pass_frames_ind_recv.msb = axienet_ior(&lp,
+						     FRER_PASS_FRAMES_INDV_OFFSET + offset + 0x4);
+
+	data->disc_frames_ind_recv.lsb = axienet_ior(&lp,
+						     FRER_DISCARD_FRAMES_INDV_OFFSET + offset);
+	data->disc_frames_ind_recv.msb =
+	axienet_ior(&lp, FRER_DISCARD_FRAMES_INDV_OFFSET + offset + 0x4);
+
+	data->pass_frames_seq_recv.lsb = axienet_ior(&lp,
+						     FRER_PASS_FRAMES_SEQ_OFFSET + offset);
+	data->pass_frames_seq_recv.msb = axienet_ior(&lp,
+						     FRER_PASS_FRAMES_SEQ_OFFSET + offset + 0x4);
+
+	data->disc_frames_seq_recv.lsb = axienet_ior(&lp,
+						     FRER_DISCARD_FRAMES_SEQ_OFFSET + offset);
+	data->disc_frames_seq_recv.msb = axienet_ior(&lp,
+						     FRER_DISCARD_FRAMES_SEQ_OFFSET + offset + 0x4);
+
+	data->rogue_frames_seq_recv.lsb = axienet_ior(&lp,
+						      FRER_ROGUE_FRAMES_SEQ_OFFSET + offset);
+	data->rogue_frames_seq_recv.msb = axienet_ior(&lp,
+						      FRER_ROGUE_FRAMES_SEQ_OFFSET + offset + 0x4);
+
+	data->seq_recv_rst.lsb = axienet_ior(&lp,
+					     SEQ_RECV_RESETS_OFFSET + offset);
+	data->seq_recv_rst.msb = axienet_ior(&lp,
+					     SEQ_RECV_RESETS_OFFSET + offset + 0x4);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_ep.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_ep.c
@@ -0,0 +1,675 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN End point driver.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_net.h>
+#include <linux/skbuff.h>
+
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_switch.h"
+
+#define TX_BD_NUM_DEFAULT	64
+#define RX_BD_NUM_DEFAULT	1024
+
+static u8 st_pcp[8];
+static uint st_count;
+module_param_array(st_pcp, byte, &st_count, 0644);
+MODULE_PARM_DESC(st_pcp, "Array of pcp values mapped to ST class at the compile time");
+
+static u8 res_pcp[8];
+static uint res_count;
+module_param_array(res_pcp, byte, &res_count, 0644);
+MODULE_PARM_DESC(res_pcp, "Array of pcp values mapped to RES class at the compile time");
+
+extern int axienet_phc_index;
+
+int tsn_data_path_open(struct net_device *ndev)
+{
+	int ret, i = 0;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct net_device *emac0_ndev = NULL;
+	struct net_device *emac1_ndev = NULL;
+	struct axienet_dma_q *q;
+	u8 emac0_addr[ETH_ALEN];
+	u8 emac1_addr[ETH_ALEN];
+	u8 ep_addr[ETH_ALEN];
+
+	static char irq_name[XAE_MAX_QUEUES + XAE_TSN_MIN_QUEUES][24];
+	u8 irq_cnt = 0;
+
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		/*MCDMA TX RESET*/
+		__axienet_device_reset_tsn(q);
+	}
+
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+
+		ret = axienet_mcdma_rx_q_init_tsn(ndev, q);
+		/* Enable interrupts for Axi MCDMA Rx
+		 */
+		sprintf(irq_name[irq_cnt], "%s_mcdma_rx_%d", ndev->name, i + 1);
+		ret = request_irq(q->rx_irq, axienet_mcdma_rx_irq_tsn,
+				  IRQF_SHARED, irq_name[irq_cnt], ndev);
+		if (ret)
+			goto err_dma_rx_irq;
+
+		tasklet_init(&lp->dma_err_tasklet[i],
+			     axienet_mcdma_err_handler_tsn,
+			     (unsigned long)lp->dq[i]);
+		napi_enable(&lp->napi[i]);
+		irq_cnt++;
+	}
+
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+
+		ret = axienet_mcdma_tx_q_init_tsn(ndev, q);
+		/* Enable interrupts for Axi MCDMA Tx */
+		sprintf(irq_name[irq_cnt], "%s_mcdma_tx_%d", ndev->name, i + 1);
+		ret = request_irq(q->tx_irq, axienet_mcdma_tx_irq_tsn,
+				  IRQF_SHARED, irq_name[irq_cnt], ndev);
+		if (ret)
+			goto err_dma_tx_irq;
+		irq_cnt++;
+	}
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	ret = axienet_tadma_open(ndev);
+	if (ret)
+		goto err_tadma;
+#endif
+	if (lp->slaves[0] && lp->slaves[1]) {
+		emac0_ndev = lp->slaves[0];
+		emac1_ndev = lp->slaves[1];
+
+		/* copy mac address of all ports */
+		memcpy(emac0_addr, emac0_ndev->dev_addr, ETH_ALEN);
+		memcpy(emac1_addr, emac1_ndev->dev_addr, ETH_ALEN);
+		memcpy(ep_addr, ndev->dev_addr, ETH_ALEN);
+
+		emac0_addr[5] = emac0_addr[5] | 0xF; /* ignore last 4 bits for comparision */
+		emac1_addr[5] = emac1_addr[5] | 0xF;
+		ep_addr[5] = ep_addr[5] | 0xF;
+
+		for (i = 0; i < ETH_ALEN; i++) {
+			if (emac0_addr[i] != emac1_addr[i]) {
+				netdev_warn(ndev, "MSB 44 bits of tsn_emac_0 and tsn_emac_1 "
+					    "are different");
+				break;
+			}
+			if (emac0_addr[i] != ep_addr[i]) {
+				netdev_warn(ndev, "MSB 44 bits of tsn_emac_0 and tsn_ep "
+					    "are different");
+				break;
+			}
+			if (emac1_addr[i] != ep_addr[i]) {
+				netdev_warn(ndev, "MSB 44 bits of tsn_emac_1 and tsn_ep "
+					    "are different");
+				break;
+			}
+		}
+	}
+
+	netif_tx_start_all_queues(ndev);
+	return 0;
+
+#ifdef CONFIG_AXIENET_HAS_TADMA
+err_tadma:
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		free_irq(q->tx_irq, ndev);
+	}
+#endif
+err_dma_tx_irq:
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		free_irq(q->rx_irq, ndev);
+	}
+err_dma_rx_irq:
+	return ret;
+}
+
+/**
+ * tsn_ep_open - TSN EP driver open routine.
+ * @ndev:       Pointer to net_device structure
+ *
+ * Return: 0, on success.
+ *          non-zero error value on failure
+ *
+ * This is the driver open routine. It also allocates interrupt service
+ * routines, enables the interrupt lines and ISR handling. Axi Ethernet
+ * core is reset through Axi DMA core. Buffer descriptors are initialized.
+ */
+static int tsn_ep_open(struct net_device *ndev)
+{
+	return tsn_data_path_open(ndev);
+}
+
+int tsn_data_path_close(struct net_device *ndev)
+{
+	u32 cr;
+	u32 i;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct axienet_dma_q *q;
+
+	for_each_tx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		cr = axienet_dma_in32(q, XAXIDMA_TX_CR_OFFSET);
+		axienet_dma_out32(q, XAXIDMA_TX_CR_OFFSET,
+				  cr & (~XAXIDMA_CR_RUNSTOP_MASK));
+		if (netif_running(ndev))
+			netif_stop_queue(ndev);
+		free_irq(q->tx_irq, ndev);
+	}
+	for_each_rx_dma_queue(lp, i) {
+		q = lp->dq[i];
+		cr = axienet_dma_in32(q, XAXIDMA_RX_CR_OFFSET);
+		axienet_dma_out32(q, XAXIDMA_RX_CR_OFFSET,
+				  cr & (~XAXIDMA_CR_RUNSTOP_MASK));
+		if (netif_running(ndev))
+			netif_stop_queue(ndev);
+		napi_disable(&lp->napi[i]);
+		tasklet_kill(&lp->dma_err_tasklet[i]);
+
+		free_irq(q->rx_irq, ndev);
+	}
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	axienet_tadma_stop(ndev);
+#endif
+	axienet_dma_bd_release_tsn(ndev);
+
+	return 0;
+}
+
+/**
+ * tsn_ep_stop - TSN EP driver stop routine.
+ * @ndev:	Pointer to net_device structure
+ *
+ * Return: 0, on success.
+ *
+ * This is the driver stop routine. It also removes the interrupt handlers
+ * and disables the interrupts. The Axi DMA Tx/Rx BDs are released.
+ */
+static int tsn_ep_stop(struct net_device *ndev)
+{
+	return tsn_data_path_close(ndev);
+}
+
+/**
+ * tsn_ep_ioctl - TSN endpoint ioctl interface.
+ * @dev: Pointer to the net_device structure
+ * @rq: Socket ioctl interface request structure
+ * @data: User data
+ * @cmd: Ioctl case
+ *
+ * Return: 0 on success, Non-zero error value on failure.
+ *
+ * This is the ioctl interface for TSN end point. Currently this
+ * supports only gate programming.
+ */
+static int tsn_ep_ioctl(struct net_device *dev, struct ifreq *rq, void __user *data, int cmd)
+{
+	switch (cmd) {
+#ifdef CONFIG_XILINX_TSN_QBV
+	case SIOCCHIOCTL:
+		return axienet_set_schedule(dev, data);
+	case SIOC_GET_SCHED:
+		return axienet_get_schedule(dev, data);
+#endif
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	case SIOC_TADMA_OFF:
+		return axienet_tadma_off(dev, data);
+	case SIOC_TADMA_STR_ADD:
+		return axienet_tadma_add_stream(dev, data);
+	case SIOC_TADMA_PROG_ALL:
+		return axienet_tadma_program(dev, data);
+	case SIOC_TADMA_STR_FLUSH:
+		return axienet_tadma_flush_stream(dev, data);
+#endif
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+u16 axienet_tsn_pcp_to_queue(struct net_device *ndev, struct sk_buff *skb)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct ethhdr *hdr = (struct ethhdr *)skb->data;
+	u16 ether_type = ntohs(hdr->h_proto);
+	u16 vlan_tci;
+	u8 pcp = 0;
+	int i;
+
+	if (unlikely(ether_type == ETH_P_8021Q)) {
+		struct vlan_ethhdr *vhdr = (struct vlan_ethhdr *)skb->data;
+
+		/* ether_type = ntohs(vhdr->h_vlan_encapsulated_proto); */
+
+		vlan_tci = ntohs(vhdr->h_vlan_TCI);
+
+		pcp = (vlan_tci & VLAN_PRIO_MASK) >> VLAN_PRIO_SHIFT;
+#ifdef CONFIG_AXIENET_HAS_TADMA
+		for (i = 0; i < st_count; i++) {
+			if (st_pcp[i] == pcp)
+				return ST_QUEUE_NUMBER;
+		}
+#endif
+		if (lp->num_tc == 3 && lp->num_tx_queues > 1) {
+			for (i = 0; i < res_count; i++) {
+				if (res_pcp[i] == pcp)
+					return RES_QUEUE_NUMBER;
+			}
+		}
+	}
+	return BE_QUEUE_NUMBER;
+}
+
+static u16 axienet_tsn_ep_select_queue(struct net_device *ndev, struct sk_buff *skb,
+				       struct net_device *sb_dev)
+{
+	return axienet_tsn_pcp_to_queue(ndev, skb);
+}
+
+/**
+ * tsn_ep_xmit - TSN endpoint xmit routine.
+ * @skb: Packet data
+ * @ndev: Pointer to the net_device structure
+ *
+ * Return: Always returns NETDEV_TX_OK.
+ *
+ * This is dummy xmit function for endpoint as all the data path is assumed to
+ * be connected by TEMAC1 as per linux view
+ */
+static int tsn_ep_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	u16 map = skb_get_queue_mapping(skb);
+
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	if (map == ST_QUEUE_NUMBER) /* ST Traffic */
+		return axienet_tadma_xmit(skb, ndev, map);
+#endif
+
+	return axienet_queue_xmit_tsn(skb, ndev, map);
+}
+
+static void tsn_ep_set_mac_address(struct net_device *ndev, const void *address)
+{
+	if (address)
+		ether_addr_copy(ndev->dev_addr, address);
+	if (!is_valid_ether_addr(ndev->dev_addr))
+		eth_hw_addr_random(ndev);
+}
+
+/**
+ * netdev_set_mac_address - Write the MAC address (from outside the driver)
+ * @ndev:	Pointer to the net_device structure
+ * @p:		6 byte Address to be written as MAC address
+ *
+ * Return: 0 for all conditions. Presently, there is no failure case.
+ *
+ * This function is called to initialize the MAC address of the Axi Ethernet
+ * core. This is the function that goes into net_device_ops structure entry
+ * ndo_set_mac_address.
+ */
+static int netdev_set_mac_address(struct net_device *ndev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	tsn_ep_set_mac_address(ndev, addr->sa_data);
+	return 0;
+}
+
+#if defined(CONFIG_XILINX_TSN_PTP)
+/**
+ * tsn_ethtools_get_ts_info - Get h/w timestamping capabilities.
+ * @ndev:       Pointer to net_device structure
+ * @info:       Pointer to ethtool_ts_info structure
+ *
+ * Return: 0
+ */
+static int tsn_ethtools_get_ts_info(struct net_device *ndev,
+				    struct ethtool_ts_info *info)
+{
+	info->phc_index = axienet_phc_index;
+	return 0;
+}
+#endif
+
+static const struct ethtool_ops ep_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_MAX_FRAMES,
+	.get_sset_count	 = axienet_sset_count_tsn,
+	.get_ethtool_stats = axienet_get_stats_tsn,
+	.get_coalesce   = axienet_ethtools_get_coalesce,
+	.set_coalesce   = axienet_ethtools_set_coalesce,
+	.get_strings = axienet_strings_tsn,
+#if defined(CONFIG_XILINX_TSN_PTP)
+	.get_ts_info    = tsn_ethtools_get_ts_info,
+#endif
+};
+
+static const struct net_device_ops ep_netdev_ops = {
+	.ndo_open = tsn_ep_open,
+	.ndo_stop = tsn_ep_stop,
+	.ndo_siocdevprivate = tsn_ep_ioctl,
+	.ndo_start_xmit = tsn_ep_xmit,
+	.ndo_set_mac_address = netdev_set_mac_address,
+	.ndo_select_queue = axienet_tsn_ep_select_queue,
+#if defined(CONFIG_XILINX_TSN_SWITCH)
+	.ndo_get_port_parent_id = tsn_switch_get_port_parent_id,
+#endif
+};
+
+static const struct of_device_id tsn_ep_of_match[] = {
+	{ .compatible = "xlnx,tsn-ep"},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, tsn_ep_of_match);
+
+/* separate function is needed to probe tsn mcdma
+ * as there is asymmetry between rx channels and tx channels
+ * having unique probe for both tsn and axienet with mcdma is not possible
+ */
+int __maybe_unused tsn_mcdma_probe(struct platform_device *pdev, struct axienet_local *lp,
+				   struct net_device *ndev)
+{
+	int i, ret = 0;
+	struct axienet_dma_q *q;
+	struct device_node *np;
+	struct resource dmares;
+	const char *str;
+	u32 num;
+
+	ret = of_property_count_strings(pdev->dev.of_node, "xlnx,channel-ids");
+	if (ret < 0)
+		return -EINVAL;
+
+	np = of_parse_phandle(pdev->dev.of_node, "axistream-connected-rx",
+			      0);
+	/* get number of associated queues */
+	ret = of_property_read_u32(np, "xlnx,num-s2mm-channels", &num);
+	if (ret < 0)
+		return -EINVAL;
+
+	lp->num_rx_queues = num;
+	pr_info("%s: num_rx_queues: %d\n", __func__, lp->num_rx_queues);
+
+	for_each_rx_dma_queue(lp, i) {
+		q = kzalloc(sizeof(*q), GFP_KERNEL);
+
+		/* parent */
+		q->lp = lp;
+		lp->dq[i] = q;
+		ret = of_property_read_string_index(pdev->dev.of_node,
+						    "xlnx,channel-ids", i,
+						    &str);
+		ret = kstrtou16(str, 16, &q->chan_id);
+		lp->qnum[i] = i;
+		lp->chan_num[i] = q->chan_id;
+	}
+
+	if (IS_ERR(np)) {
+		dev_err(&pdev->dev, "could not find DMA node\n");
+		return ret;
+	}
+
+	ret = of_address_to_resource(np, 0, &dmares);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to get DMA resource\n");
+		return ret;
+	}
+
+	lp->mcdma_regs = devm_ioremap_resource(&pdev->dev, &dmares);
+	if (IS_ERR(lp->mcdma_regs)) {
+		dev_err(&pdev->dev, "iormeap failed for the dma\n");
+		ret = PTR_ERR(lp->mcdma_regs);
+		return ret;
+	}
+
+	axienet_mcdma_rx_probe_tsn(pdev, np, ndev);
+	axienet_mcdma_tx_probe_tsn(pdev, np, lp);
+
+	return 0;
+}
+
+static const struct axienet_config tsn_endpoint_cfg = {
+	.mactype = XAXIENET_1G,
+	.setoptions = NULL,
+	.tx_ptplen = XAE_TX_PTP_LEN,
+};
+
+/**
+ *axienet_get_pcp_mask - gets the compile time pcp values that
+ *are mapped to ST and RES traffic from uEnv.txt and assigns them
+ *to st_pcp and res_pcp fields of axienet_local structure
+ *@lp:		axienet local structure
+ *@num_tc:	number of traffic classes
+ *
+ * Return: Always returns 0
+ */
+int axienet_get_pcp_mask(struct axienet_local *lp, u16 num_tc)
+{
+	u8 i;
+	u8 invalid_pcp = 0;
+
+	lp->st_pcp = 0;
+	lp->res_pcp = 0;
+	if (st_count == 0 || st_count > 8) {
+		lp->st_pcp = 1 << 4;
+	} else {
+		for (i = 0; i < st_count; i++) {
+			if (st_pcp[i] >= 8) {
+				invalid_pcp = 1;
+				break;
+			}
+			lp->st_pcp = lp->st_pcp | 1 << st_pcp[i];
+		}
+		if (invalid_pcp) {
+			pr_warn("pcp value cannot be greater than or equal to 8\n");
+			lp->st_pcp = 1 << 4;
+			invalid_pcp = 0;
+		}
+	}
+	if (num_tc == 3) {
+		if (res_count == 0 || res_count > 8) {
+			lp->res_pcp = 1 << 2 | 1 << 3;
+		} else {
+			for (i = 0; i < res_count; i++) {
+				if (res_pcp[i] >= 8) {
+					invalid_pcp = 1;
+					break;
+				}
+				lp->res_pcp = lp->res_pcp | 1 << res_pcp[i];
+			}
+			if (invalid_pcp) {
+				pr_warn("pcp value cannot be greater than or equal to 8\n");
+				lp->res_pcp = 1 << 2 | 1 << 3;
+			}
+		}
+	}
+	return 0;
+}
+
+/**
+ * tsn_ep_probe - TSN ep pointer probe function.
+ * @pdev:	Pointer to platform device structure.
+ *
+ * Return: 0, on success
+ *	    Non-zero error value on failure.
+ *
+ * This is the probe routine for TSN endpoint driver.
+ */
+static int tsn_ep_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct axienet_local *lp;
+	struct net_device *ndev;
+	struct resource *ethres;
+	u16 num_queues = XAE_MAX_QUEUES;
+	u16 num_tc = 0;
+	struct device_node *np;
+	char irq_name[32];
+
+	ndev = alloc_netdev_mq(sizeof(*lp), "ep",
+			       NET_NAME_UNKNOWN, ether_setup, num_queues);
+	if (!ndev)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ndev);
+
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+	ndev->flags &= ~IFF_MULTICAST;  /* clear multicast */
+	ndev->features = NETIF_F_SG;
+	ndev->netdev_ops = &ep_netdev_ops;
+	ndev->ethtool_ops = &ep_ethtool_ops;
+
+	/* MTU range: 64 - 9000 */
+	ndev->min_mtu = 64;
+	ndev->max_mtu = XAE_JUMBO_MTU;
+
+	lp = netdev_priv(ndev);
+	lp->ndev = ndev;
+	lp->dev = &pdev->dev;
+	lp->options = XAE_OPTION_DEFAULTS;
+	lp->tx_bd_num = TX_BD_NUM_DEFAULT;
+	lp->rx_bd_num = RX_BD_NUM_DEFAULT;
+	lp->switch_prt = PORT_EP;
+
+	/* TODO
+	 * there are two temacs or two slaves to ep
+	 * get this infor from design?
+	 */
+	lp->slaves[0] = NULL;
+	lp->slaves[1] = NULL;
+	lp->ex_ep = NULL;
+	lp->packet_switch = 0;
+
+	lp->axienet_config = &tsn_endpoint_cfg;
+
+	lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
+
+	/* check if ep has dma connected
+	 * in a ep_only system dma(mcdma/tadma) is connected to temac1
+	 */
+	np = of_parse_phandle(pdev->dev.of_node, "axistream-connected-rx", 0);
+	if (!np) {
+		/* dont expose ep dev in ep_only system
+		 * all functionality handled by temac1/eth1
+		 */
+		free_netdev(ndev);
+		of_node_put(np);
+		return 0;
+	}
+
+	/* Setup checksum offload, but default to off if not specified */
+	lp->features = 0;
+
+	lp->eth_hasnobuf = of_property_read_bool(pdev->dev.of_node,
+						 "xlnx,eth-hasnobuf");
+
+	/* Retrieve the MAC address */
+	ret = of_get_mac_address(pdev->dev.of_node, ndev->dev_addr);
+	if (ret) {
+		dev_err(&pdev->dev, "could not find MAC address\n");
+		eth_hw_addr_random(ndev);
+	}
+	if (!is_valid_ether_addr(ndev->dev_addr))
+		eth_hw_addr_random(ndev);
+
+	ret = tsn_mcdma_probe(pdev, lp, ndev);
+	if (ret) {
+		dev_err(&pdev->dev, "Getting MCDMA resource failed\n");
+		goto free_netdev;
+	}
+
+#ifdef CONFIG_AXIENET_HAS_TADMA
+	ret = axienet_tadma_probe(pdev, ndev);
+	if (ret) {
+		dev_err(&pdev->dev, "Getting TADMA resource failed\n");
+		goto free_netdev;
+	}
+#endif
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-tc", &num_tc);
+	if (ret || (num_tc != 2 && num_tc != 3))
+		lp->num_tc = XAE_MAX_TSN_TC;
+	else
+		lp->num_tc = num_tc;
+	axienet_get_pcp_mask(lp, lp->num_tc);
+	/* Map device registers */
+	ethres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	lp->regs = devm_ioremap_resource(&pdev->dev, ethres);
+	if (IS_ERR(lp->regs)) {
+		ret = PTR_ERR(lp->regs);
+		goto free_netdev;
+	}
+#ifdef CONFIG_XILINX_TSN_QBV
+	lp->qbv_regs = lp->regs;
+#endif
+
+	sprintf(irq_name, "tsn_ep_scheduler_irq");
+	lp->qbv_irq = platform_get_irq_byname(pdev, irq_name);
+#ifdef CONFIG_XILINX_TSN_QBV
+	axienet_qbv_init(ndev);
+#endif
+
+	ret = register_netdev(lp->ndev);
+	if (ret) {
+		dev_err(lp->dev, "register_netdev() error (%i)\n", ret);
+		goto free_netdev;
+	}
+	return ret;
+
+free_netdev:
+	free_netdev(ndev);
+
+	return ret;
+}
+
+static int tsn_ep_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+
+#ifdef CONFIG_XILINX_TSN_QBV
+	axienet_qbv_remove(ndev);
+#endif
+	unregister_netdev(ndev);
+
+	free_netdev(ndev);
+
+	return 0;
+}
+
+static struct platform_driver tsn_ep_driver = {
+	.probe = tsn_ep_probe,
+	.remove = tsn_ep_remove,
+	.driver = {
+		 .name = "tsn_ep_axienet",
+		 .of_match_table = tsn_ep_of_match,
+	},
+};
+
+module_platform_driver(tsn_ep_driver);
+
+MODULE_DESCRIPTION("Xilinx Axi Ethernet driver");
+MODULE_AUTHOR("Xilinx");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_ep_ex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_ep_ex.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN End point driver.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_net.h>
+#include <linux/skbuff.h>
+
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_switch.h"
+
+static const struct of_device_id tsn_ex_ep_of_match[] = {
+	{ .compatible = "xlnx,tsn-ex-ep"},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, tsn_ex_ep_of_match);
+
+static int tsn_ex_ep_open(struct net_device *ndev)
+{
+	return 0;
+}
+
+static int tsn_ex_ep_stop(struct net_device *ndev)
+{
+	return 0;
+}
+
+static int tsn_ex_ep_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct net_device *master = lp->master;
+
+	skb->dev = master;
+	dev_queue_xmit(skb);
+	return NETDEV_TX_OK;
+}
+
+static void tsn_ex_ep_set_mac_address(struct net_device *ndev, const void *address)
+{
+	if (address)
+		ether_addr_copy(ndev->dev_addr, address);
+	if (!is_valid_ether_addr(ndev->dev_addr))
+		eth_hw_addr_random(ndev);
+}
+
+static int netdev_set_ex_ep_mac_address(struct net_device *ndev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	tsn_ex_ep_set_mac_address(ndev, addr->sa_data);
+	return 0;
+}
+
+static const struct net_device_ops ex_ep_netdev_ops = {
+	.ndo_open = tsn_ex_ep_open,
+	.ndo_stop = tsn_ex_ep_stop,
+	.ndo_start_xmit = tsn_ex_ep_xmit,
+	.ndo_set_mac_address = netdev_set_ex_ep_mac_address,
+};
+
+static int tsn_ex_ep_probe(struct platform_device *pdev)
+{
+	struct axienet_local *lp;
+	struct net_device *ndev;
+	struct device_node *ep_node;
+	struct axienet_local *ep_lp;
+	const void *mac_addr;
+	int ret = 0;
+	const void *packet_switch;
+
+	ndev = alloc_netdev(sizeof(*lp), "exep",
+			    NET_NAME_UNKNOWN, ether_setup);
+	if (!ndev)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ndev);
+
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+	ndev->flags &= ~IFF_MULTICAST;  /* clear multicast */
+	ndev->features = NETIF_F_SG;
+	ndev->netdev_ops = &ex_ep_netdev_ops;
+
+	/* MTU range: 64 - 9000 */
+	ndev->min_mtu = 64;
+	ndev->max_mtu = XAE_JUMBO_MTU;
+
+	lp = netdev_priv(ndev);
+	lp->ndev = ndev;
+	lp->dev = &pdev->dev;
+	lp->options = XAE_OPTION_DEFAULTS;
+	/* Retrieve the MAC address */
+	ret = of_get_mac_address(pdev->dev.of_node, (u8 *)mac_addr);
+	if (ret) {
+		dev_err(&pdev->dev, "could not find MAC address\n");
+		goto free_netdev;
+	}
+	tsn_ex_ep_set_mac_address(ndev, mac_addr);
+	packet_switch = of_get_property(pdev->dev.of_node, "packet-switch", NULL);
+	ep_node = of_parse_phandle(pdev->dev.of_node, "tsn,endpoint", 0);
+
+	lp->master = of_find_net_device_by_node(ep_node);
+	ret = register_netdev(lp->ndev);
+	if (ret) {
+		dev_err(lp->dev, "register_netdev() error (%i)\n", ret);
+		goto free_netdev;
+	}
+	ep_lp = netdev_priv(lp->master);
+	ep_lp->ex_ep = ndev;
+	if (packet_switch)
+		ep_lp->packet_switch = 1;
+	return ret;
+free_netdev:
+	free_netdev(ndev);
+
+	return ret;
+}
+
+static int tsn_ex_ep_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+
+	unregister_netdev(ndev);
+	free_netdev(ndev);
+	return 0;
+}
+
+static struct platform_driver tsn_ex_ep_driver = {
+	.probe = tsn_ex_ep_probe,
+	.remove = tsn_ex_ep_remove,
+	.driver = {
+		 .name = "tsn_ex_ep_axienet",
+		 .of_match_table = tsn_ex_ep_of_match,
+	},
+};
+
+module_platform_driver(tsn_ex_ep_driver);
+
+MODULE_DESCRIPTION("Xilinx Axi Ethernet driver");
+MODULE_AUTHOR("Xilinx");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_ip.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_ip.c
@@ -0,0 +1,455 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Xilinx FPGA Xilinx TSN IP driver.
+ *
+ * Copyright (C) 2018 Xilinx, Inc. All rights reserved.
+ *
+ * Author: Priyadarshini Babu <priyadar@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/netdevice.h>
+#include <linux/skbuff.h>
+#include <linux/phy.h>
+#include <linux/udp.h>
+#include <linux/mii.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_address.h>
+#include <linux/xilinx_phy.h>
+
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_switch.h"
+
+#ifdef CONFIG_XILINX_TSN_PTP
+#include "xilinx_tsn_ptp.h"
+#include "xilinx_tsn_timer.h"
+#endif
+
+#define TSN_TX_BE_QUEUE  0
+#define TSN_TX_RES_QUEUE 1
+#define TSN_TX_ST_QUEUE  2
+
+#define XAE_TEMAC1 0
+#define XAE_TEMAC2 1
+static const struct of_device_id tsn_ip_of_match[] = {
+	{ .compatible = "xlnx,tsn-endpoint-ethernet-mac-1.0"},
+	{ .compatible = "xlnx,tsn-endpoint-ethernet-mac-2.0"},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, tsn_ip_of_match);
+
+/**
+ * tsn_ip_probe - TSN ip pointer probe function.
+ * @pdev:	Pointer to platform device structure.
+ *
+ * Return: 0, on success
+ *	    Non-zero error value on failure.
+ *
+ * This is the probe routine for TSN driver.
+ */
+static int tsn_ip_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+
+	pr_info("TSN endpoint ethernet mac Probe\n");
+
+	ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+	if (ret)
+		pr_err("TSN endpoint probe error (%i)\n", ret);
+
+	return ret;
+}
+
+static int tsn_ip_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+u16 axienet_tsn_select_queue(struct net_device *ndev, struct sk_buff *skb,
+			     struct net_device *sb_dev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct ethhdr *hdr = (struct ethhdr *)skb->data;
+#ifdef CONFIG_XILINX_TSN_PTP
+	const struct udphdr *udp;
+
+	udp = udp_hdr(skb);
+	if (hdr->h_proto == htons(ETH_P_1588) ||
+	    (lp->current_rx_filter == HWTSTAMP_FILTER_PTP_V2_L4_EVENT &&
+	     hdr->h_proto == htons(ETH_P_IP) && udp->dest == htons(0x013f))) {
+		return PTP_QUEUE_NUMBER;
+	}
+#endif
+	if (lp->abl_reg & TSN_BRIDGEEP_EPONLY)
+		return axienet_tsn_pcp_to_queue(ndev, skb);
+
+	return BE_QUEUE_NUMBER;
+}
+
+/**
+ * axienet_tsn_xmit - Starts the TSN transmission.
+ * @skb:	sk_buff pointer that contains data to be Txed.
+ * @ndev:	Pointer to net_device structure.
+ *
+ * Return: NETDEV_TX_OK, on success
+ *	    Non-zero error value on failure.
+ *
+ * This function is invoked from upper layers to initiate transmission. The
+ * function uses the next available free BDs and populates their fields to
+ * start the transmission. Use axienet_ptp_xmit() for PTP 1588 packets and
+ * use master EP xmit for other packets transmission.
+ */
+int axienet_tsn_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct net_device *master = lp->master;
+	u16 map = skb_get_queue_mapping(skb);
+
+#ifdef CONFIG_XILINX_TSN_PTP
+	/* check if skb is a PTP frame ? */
+	if (map == PTP_QUEUE_NUMBER)
+		return axienet_ptp_xmit(skb, ndev);
+#endif
+	if (lp->abl_reg & TSN_BRIDGEEP_EPONLY) {
+#ifdef CONFIG_AXIENET_HAS_TADMA
+		if (map == ST_QUEUE_NUMBER) /* ST Traffic */
+			return axienet_tadma_xmit(skb, ndev, map);
+#endif
+		return axienet_queue_xmit_tsn(skb, ndev, map);
+	}
+	/* use EP to xmit non-PTP frames */
+	skb->dev = master;
+	dev_queue_xmit(skb);
+
+	return NETDEV_TX_OK;
+}
+
+/**
+ * axienet_tsn_probe - TSN mac probe function.
+ * @pdev:	Pointer to platform device structure.
+ * @lp:		Pointer to axienet local structure
+ * @ndev:	Pointer to net_device structure.
+ *
+ * Return: 0, on success
+ *	    Non-zero error value on failure.
+ *
+ * This is the probe for TSN mac nodes.
+ */
+int axienet_tsn_probe(struct platform_device *pdev,
+		      struct axienet_local *lp,
+		      struct net_device *ndev)
+{
+	int ret = 0;
+	char irq_name[32];
+	bool slave = false;
+	u8     temac_no;
+	u32 qbv_addr, qbv_size;
+	struct device_node *ep_node;
+	struct axienet_local *ep_lp;
+
+	slave = of_property_read_bool(pdev->dev.of_node,
+				      "xlnx,tsn-slave");
+	if (slave) {
+		temac_no = XAE_TEMAC2;
+		lp->switch_prt = PORT_MAC2;
+	} else {
+		temac_no = XAE_TEMAC1;
+		lp->switch_prt = PORT_MAC1;
+	}
+	lp->current_rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
+	sprintf(irq_name, "interrupt_ptp_rx_%d", temac_no + 1);
+	lp->ptp_rx_irq = platform_get_irq_byname(pdev, irq_name);
+
+	pr_info("ptp RX irq: %d %s\n", lp->ptp_rx_irq, irq_name);
+	sprintf(irq_name, "interrupt_ptp_tx_%d", temac_no + 1);
+	lp->ptp_tx_irq = platform_get_irq_byname(pdev, irq_name);
+	pr_info("ptp TX irq: %d %s\n", lp->ptp_tx_irq, irq_name);
+
+	sprintf(irq_name, "tsn_switch_scheduler_irq_%d", temac_no + 1);
+	lp->qbv_irq = platform_get_irq_byname(pdev, irq_name);
+
+	/*Ignoring if the qbv_irq is not exist*/
+	if (lp->qbv_irq > 0)
+		pr_info("qbv_irq: %d %s\n", lp->qbv_irq, irq_name);
+
+	spin_lock_init(&lp->ptp_tx_lock);
+
+	if (temac_no == XAE_TEMAC1)
+		lp->timer_priv = axienet_ptp_timer_probe((lp->regs + XAE_RTC_OFFSET), pdev);
+
+	/* enable VLAN */
+	lp->options |= XAE_OPTION_VLAN;
+	axienet_setoptions_tsn(lp->ndev, lp->options);
+
+	/* get the ep device */
+	ep_node = of_parse_phandle(pdev->dev.of_node, "tsn,endpoint", 0);
+
+	if (ep_node)
+		lp->master = of_find_net_device_by_node(ep_node);
+
+	if (!lp->master) {
+		netdev_info(ndev, "Defer probe as ep is not probed\n");
+		ret = -EPROBE_DEFER;
+		goto err;
+	}
+
+	lp->abl_reg = axienet_ior(lp, XAE_TSN_ABL_OFFSET);
+
+	/* in ep only case tie the data path to eth1 */
+	if (lp->abl_reg & TSN_BRIDGEEP_EPONLY && temac_no == XAE_TEMAC1) {
+		axienet_get_pcp_mask(lp, lp->num_tc);
+		ret = tsn_mcdma_probe(pdev, lp, ndev);
+		if (ret) {
+			dev_err(&pdev->dev, "Getting MCDMA resource failed\n");
+			goto err_1;
+		}
+#ifdef CONFIG_AXIENET_HAS_TADMA
+		ret = axienet_tadma_probe(pdev, ndev);
+		if (ret) {
+			dev_err(&pdev->dev, "Getting TADMA resource failed\n");
+			goto err_1;
+		}
+#endif
+	}
+
+#ifdef CONFIG_XILINX_TSN_QBV
+	lp->qbv_regs = NULL;
+	if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY)) {
+		of_property_read_u32(pdev->dev.of_node, "xlnx,qbv-addr",
+				     &qbv_addr);
+		of_property_read_u32(pdev->dev.of_node, "xlnx,qbv-size",
+				     &qbv_size);
+	} else {
+		struct resource res;
+
+		/* get qbv info from ep_node */
+		if (of_address_to_resource(ep_node, 0, &res) < 0)
+			dev_err(&pdev->dev, "error reading reg property\n");
+		qbv_addr = res.start;
+		qbv_size = res.end - res.start;
+	}
+	lp->qbv_regs = devm_ioremap(&pdev->dev, qbv_addr, qbv_size);
+	if (IS_ERR(lp->qbv_regs)) {
+		dev_err(&pdev->dev, "ioremap failed for the qbv\n");
+		ret = PTR_ERR(lp->qbv_regs);
+		return ret;
+	}
+	ret = axienet_qbv_init(ndev);
+#endif
+	if (!(lp->abl_reg & TSN_BRIDGEEP_EPONLY)) {
+		/* EP+Switch */
+		/* store the slaves to master(ep) */
+		ep_lp = netdev_priv(lp->master);
+		ep_lp->slaves[temac_no] = ndev;
+	}
+
+	return 0;
+err_1:
+	return -EINVAL;
+err:
+	if (lp->timer_priv)
+		axienet_ptp_timer_remove(lp->timer_priv);
+	return ret;
+}
+
+/**
+ * axienet_device_reset - Reset and initialize the Axi Ethernet hardware.
+ * @ndev:	Pointer to the net_device structure
+ *
+ * This function is called to reset and initialize the Axi Ethernet core. This
+ * is typically called during initialization. It does a reset of the Axi DMA
+ * Rx/Tx channels and initializes the Axi DMA BDs. Since Axi DMA reset lines
+ * areconnected to Axi Ethernet reset lines, this in turn resets the Axi
+ * Ethernet core. No separate hardware reset is done for the Axi Ethernet
+ * core.
+ */
+static void axienet_device_reset(struct net_device *ndev)
+{
+	u32 axienet_status;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
+
+	lp->options |= XAE_OPTION_VLAN;
+	lp->options &= (~XAE_OPTION_JUMBO);
+
+	if (ndev->mtu > XAE_MTU && ndev->mtu <= XAE_JUMBO_MTU) {
+		lp->max_frm_size = ndev->mtu + VLAN_ETH_HLEN +
+					XAE_TRL_SIZE;
+		if (lp->max_frm_size <= lp->rxmem)
+			lp->options |= XAE_OPTION_JUMBO;
+	}
+
+	axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+	axienet_status &= ~XAE_RCW1_RX_MASK;
+	axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
+
+	if (lp->axienet_config->mactype == XAXIENET_1G &&
+	    !lp->eth_hasnobuf) {
+		axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+		if (axienet_status & XAE_INT_RXRJECT_MASK)
+			axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+
+		/* Enable Receive errors */
+		axienet_iow(lp, XAE_IE_OFFSET, XAE_INT_RECV_ERROR_MASK);
+	}
+
+	axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+	lp->axienet_config->setoptions(ndev, lp->options &
+				       ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+
+	axienet_set_mac_address_tsn(ndev, NULL);
+	axienet_set_multicast_list_tsn(ndev);
+	lp->axienet_config->setoptions(ndev, lp->options);
+
+	netif_trans_update(ndev);
+}
+
+/**
+ * axienet_tsn_open - TSN driver open routine.
+ * @ndev:	Pointer to net_device structure
+ *
+ * Return: 0, on success.
+ *	    non-zero error value on failure
+ *
+ * This is the driver open routine. It calls phy_start to start the PHY device.
+ * It also allocates interrupt service routines, enables the interrupt lines
+ * and ISR handling. Axi Ethernet core is reset through Axi DMA core.
+ */
+int axienet_tsn_open(struct net_device *ndev)
+{
+	int ret;
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct net_device *emac0_ndev = NULL;
+	struct net_device *emac1_ndev = NULL;
+	struct axienet_local *ep_node = NULL;
+	struct phy_device *phydev = NULL;
+	u8 emac0_addr[ETH_ALEN];
+	u8 emac1_addr[ETH_ALEN];
+	u8 ep_addr[ETH_ALEN];
+	int i;
+
+	axienet_device_reset(ndev);
+
+	if (lp->phy_node) {
+		phydev = of_phy_connect(lp->ndev, lp->phy_node,
+					axienet_adjust_link_tsn,
+					lp->phy_flags,
+					lp->phy_mode);
+		if (!phydev)
+			dev_err(lp->dev, "of_phy_connect() failed\n");
+		else
+			phy_start(phydev);
+	}
+
+	INIT_WORK(&lp->tx_tstamp_work, axienet_tx_tstamp);
+	skb_queue_head_init(&lp->ptp_txq);
+
+	lp->ptp_rx_hw_pointer = 0;
+	lp->ptp_rx_sw_pointer = 0xff;
+
+	axienet_iow(lp, PTP_RX_CONTROL_OFFSET, PTP_RX_PACKET_CLEAR);
+
+	ret = request_irq(lp->ptp_rx_irq, axienet_ptp_rx_irq,
+			  0, "ptp_rx", ndev);
+	if (ret)
+		goto err_ptp_rx_irq;
+
+	ret = request_irq(lp->ptp_tx_irq, axienet_ptp_tx_irq,
+			  0, "ptp_tx", ndev);
+	if (ret)
+		goto err_ptp_tx_irq;
+
+	if (lp->abl_reg & TSN_BRIDGEEP_EPONLY)
+		tsn_data_path_open(ndev);
+
+	if (lp->master) {
+		ep_node = netdev_priv(lp->master);
+		emac0_ndev = ep_node->slaves[0];
+		emac1_ndev = ep_node->slaves[1];
+
+		if(ep_node && emac0_ndev && emac1_ndev) {
+			/* copy mac address of all ports */
+			memcpy(emac0_addr, emac0_ndev->dev_addr, ETH_ALEN);
+			memcpy(emac1_addr, emac1_ndev->dev_addr, ETH_ALEN);
+			memcpy(ep_addr, ndev->dev_addr, ETH_ALEN);
+
+			emac0_addr[5] = emac0_addr[5] | 0xF; /* ignore last 4 bits for comparision */
+			emac1_addr[5] = emac1_addr[5] | 0xF;
+			ep_addr[5] = ep_addr[5] | 0xF;
+
+			for (i = 0; i < ETH_ALEN; i++) {
+				if (emac0_addr[i] != emac1_addr[i]) {
+					netdev_warn(ndev, "MSB 44 bits of tsn_emac_0 and "
+						    "tsn_emac_1 are different");
+					break;
+				}
+				if (emac0_addr[i] != ep_addr[i]) {
+					netdev_warn(ndev, "MSB 44 bits of tsn_emac_0 and "
+						    "tsn_ep are different");
+					break;
+				}
+				if (emac1_addr[i] != ep_addr[i]) {
+					netdev_warn(ndev, "MSB 44 bits of tsn_emac_1 and "
+						    "tsn ep are different");
+				break;
+				}
+			}
+		}
+	}
+
+	netif_tx_start_all_queues(ndev);
+
+	return 0;
+
+err_ptp_tx_irq:
+	free_irq(lp->ptp_rx_irq, ndev);
+err_ptp_rx_irq:
+	return ret;
+}
+
+int axienet_tsn_stop(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	free_irq(lp->ptp_tx_irq, ndev);
+	free_irq(lp->ptp_rx_irq, ndev);
+
+	if (lp->axienet_config->mactype == XAXIENET_1G && !lp->eth_hasnobuf)
+		free_irq(lp->eth_irq, ndev);
+
+	if (ndev->phydev)
+		phy_disconnect(ndev->phydev);
+
+	if (lp->abl_reg & TSN_BRIDGEEP_EPONLY)
+		tsn_data_path_close(ndev);
+
+	return 0;
+}
+
+static struct platform_driver tsn_ip_driver = {
+	.probe = tsn_ip_probe,
+	.remove = tsn_ip_remove,
+	.driver = {
+		 .name = "tsn_ip_axienet",
+		 .of_match_table = tsn_ip_of_match,
+	},
+};
+
+module_platform_driver(tsn_ip_driver);
+
+MODULE_DESCRIPTION("Xilinx Axi Ethernet driver");
+MODULE_AUTHOR("Xilinx");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_preemption.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_preemption.c
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN QBU/QBR - Frame Preemption module.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Priyadarshini Babu <priyadar@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_preemption.h"
+
+/**
+ * axienet_preemption -  Configure Frame Preemption
+ * @ndev: Pointer to the net_device structure
+ * @useraddr: Value to be programmed
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_preemption(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u8 preemp;
+
+	if (copy_from_user(&preemp, useraddr, sizeof(preemp)))
+		return -EFAULT;
+
+	axienet_iow(lp, PREEMPTION_ENABLE_REG, preemp & PREEMPTION_ENABLE);
+	return 0;
+}
+
+/**
+ * axienet_preemption_ctrl_ethtool -  Configure Frame Preemption Control register
+ * @ndev: Pointer to the net_device structure
+ * @config_data: Pointer to the mm cfg data struct
+ * @extack: Pointer to the netlink_ext_ack struct
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_preemption_ctrl_ethtool(struct net_device *ndev, struct ethtool_mm_cfg *config_data,
+				    struct netlink_ext_ack *extack)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	bool preemption_support;
+	int add_frag_size, err;
+	u32 value;
+
+	value = axienet_ior(lp, XAE_TSN_ABL_OFFSET);
+	preemption_support = (value & PREEMPTION_SUPPORT) ? 1 : 0;
+	if (!preemption_support)
+		return -EOPNOTSUPP;
+
+	err = ethtool_mm_frag_size_min_to_add(config_data->tx_min_frag_size,
+					      &add_frag_size, extack);
+	if (err)
+		return err;
+
+	if (config_data->tx_enabled) {
+		value = axienet_ior(lp, PREEMPTION_ENABLE_REG);
+		value = value | config_data->tx_enabled;
+		axienet_iow(lp, PREEMPTION_ENABLE_REG, value);
+	}
+
+	value = axienet_ior(lp, PREEMPTION_CTRL_STS_REG);
+
+	value &= ~(VERIFY_TIMER_VALUE_MASK << VERIFY_TIMER_VALUE_SHIFT);
+	value |= (config_data->verify_time << VERIFY_TIMER_VALUE_SHIFT);
+	value &= ~(ADDITIONAL_FRAG_SIZE_MASK << ADDITIONAL_FRAG_SIZE_SHIFT);
+	value |= (add_frag_size << ADDITIONAL_FRAG_SIZE_SHIFT);
+
+	if (!config_data->verify_enabled) {
+		value &= ~(DISABLE_PREEMPTION_VERIFY);
+		value |= !(config_data->verify_enabled);
+	}
+
+	axienet_iow(lp, PREEMPTION_CTRL_STS_REG, value);
+	return 0;
+}
+
+/**
+ * axienet_preemption_ctrl -  Configure Frame Preemption Control register
+ * @ndev: Pointer to the net_device structure
+ * @useraddr: Value to be programmed
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_preemption_ctrl(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct preempt_ctrl_sts data;
+	u32 value;
+
+	if (copy_from_user(&data, useraddr, sizeof(struct preempt_ctrl_sts)))
+		return -EFAULT;
+	value = axienet_ior(lp, PREEMPTION_CTRL_STS_REG);
+
+	value &= ~(VERIFY_TIMER_VALUE_MASK << VERIFY_TIMER_VALUE_SHIFT);
+	value |= (data.verify_timer_value << VERIFY_TIMER_VALUE_SHIFT);
+	value &= ~(ADDITIONAL_FRAG_SIZE_MASK << ADDITIONAL_FRAG_SIZE_SHIFT);
+	value |= (data.additional_frag_size << ADDITIONAL_FRAG_SIZE_SHIFT);
+	value &= ~(DISABLE_PREEMPTION_VERIFY);
+	value |= (data.disable_preemp_verify);
+
+	axienet_iow(lp, PREEMPTION_CTRL_STS_REG, value);
+	return 0;
+}
+
+/**
+ * axienet_preemption_sts_ethtool -  Get Frame Preemption Status
+ * @ndev: Pointer to the net_device structure
+ * @state: Pointer to ethtool_mm_state struct
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_preemption_sts_ethtool(struct net_device *ndev, struct ethtool_mm_state *state)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 value;
+
+	value = axienet_ior(lp, XAE_TSN_ABL_OFFSET);
+	state->pmac_enabled = (value & PREEMPTION_SUPPORT) ? 1 : 0;
+	if (!state->pmac_enabled)
+		return -EOPNOTSUPP;
+
+	state->max_verify_time = MAX_VERIFY_TIME;
+	value = axienet_ior(lp, PREEMPTION_ENABLE_REG);
+	state->tx_enabled = value & PREEMPTION_ENABLE;
+
+	value = axienet_ior(lp, PREEMPTION_CTRL_STS_REG);
+	state->tx_active = (value & TX_PREEMPTION_STS) ? 1 : 0;
+	state->verify_status = ((value >> MAC_MERGE_TX_VERIFY_STS_SHIFT)
+				 & MAC_MERGE_TX_VERIFY_STS_MASK) + 1;
+	state->verify_time = (value >> VERIFY_TIMER_VALUE_SHIFT) &
+					VERIFY_TIMER_VALUE_MASK;
+	state->tx_min_frag_size = ethtool_mm_frag_size_add_to_min((value
+								   >> ADDITIONAL_FRAG_SIZE_SHIFT)
+								   & ADDITIONAL_FRAG_SIZE_MASK);
+	state->rx_min_frag_size = ETH_ZLEN;
+	state->verify_enabled = ~(value & DISABLE_PREEMPTION_VERIFY);
+
+	return 0;
+}
+
+/**
+ * axienet_preemption_sts -  Get Frame Preemption Status
+ * @ndev: Pointer to the net_device structure
+ * @useraddr: return value, containing Frame Preemption status
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_preemption_sts(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct preempt_status status;
+	u32 value;
+
+	value = axienet_ior(lp, PREEMPTION_ENABLE_REG);
+	status.preemp_en = value & PREEMPTION_ENABLE;
+	value = axienet_ior(lp, XAE_TSN_ABL_OFFSET);
+	status.preemp_sup = (value & PREEMPTION_SUPPORT) ? 1 : 0;
+
+	value = axienet_ior(lp, PREEMPTION_CTRL_STS_REG);
+	status.ctrl.tx_preemp_sts = (value & TX_PREEMPTION_STS) ? 1 : 0;
+	status.ctrl.mac_tx_verify_sts = (value >> MAC_MERGE_TX_VERIFY_STS_SHIFT)
+					& MAC_MERGE_TX_VERIFY_STS_MASK;
+	status.ctrl.verify_timer_value = (value >> VERIFY_TIMER_VALUE_SHIFT) &
+					VERIFY_TIMER_VALUE_MASK;
+	status.ctrl.additional_frag_size = (value >> ADDITIONAL_FRAG_SIZE_SHIFT)
+						& ADDITIONAL_FRAG_SIZE_MASK;
+	status.ctrl.disable_preemp_verify = value & DISABLE_PREEMPTION_VERIFY;
+
+	if (copy_to_user(useraddr, &status, sizeof(struct preempt_status)))
+		return -EFAULT;
+	return 0;
+}
+
+int axienet_preemption_receive(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 value;
+	u8 preemption_support;
+
+	value = axienet_ior(lp, XAE_TSN_ABL_OFFSET);
+	preemption_support = (value & PREEMPTION_SUPPORT) ? 1 : 0;
+
+	if (!preemption_support)
+		return -EOPNOTSUPP;
+
+	value = axienet_ior(lp, PREEMPTION_ENABLE_REG);
+	value = value | PREEMPTION_ENABLE;
+	axienet_iow(lp, PREEMPTION_ENABLE_REG, value);
+	return 0;
+}
+
+/**
+ * statistic_cnts -  Read statistics counter registers
+ * @ndev: Pointer to the net_device structure
+ * @ptr: Buffer addr to fill the counter values
+ * @count: read #count number of registers
+ * @addr_off: Register address to be read
+ */
+static void statistic_cnts(struct net_device *ndev, void *ptr,
+			   unsigned int count, unsigned int addr_off)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int *buf = (int *)ptr;
+	int i = 0;
+
+	for (i = 0; i < count; i++) {
+		buf[i] = axienet_ior(lp, addr_off);
+		addr_off += 4;
+	}
+}
+
+/**
+ * axienet_preemption_cnt_ethtool -  Get Frame Preemption Statistics counter
+ * @ndev: Pointer to the net_device structure
+ * @stats: return value, containing counters value
+ * Return: 0 on success, Non-zero error value on failure
+ */
+void axienet_preemption_cnt_ethtool(struct net_device *ndev, struct ethtool_mm_stats *stats)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	stats->MACMergeFrameAssErrorCount = axienet_ior64(lp,
+							  MAC_MERGE_FRAME_ASSEMBLY_ERROR_COUNT_REG);
+	stats->MACMergeFrameSmdErrorCount = axienet_ior64(lp, MAC_MERGE_FRAME_SMD_ERROR_COUNT_REG);
+	stats->MACMergeFrameAssOkCount = axienet_ior64(lp,
+						       MAC_MERGE_FRAME_ASSEMBLY_OK_COUNT_RX_REG);
+	stats->MACMergeFragCountRx = axienet_ior64(lp, MAC_MERGE_FRAG_COUNT_RX_REG);
+	stats->MACMergeFragCountTx = axienet_ior64(lp, MAC_MERGE_FRAG_COUNT_TX_REG);
+	stats->MACMergeHoldCount = axienet_ior64(lp, MAC_MERGE_HOLD_COUNT_REG);
+}
+
+/**
+ * axienet_preemption_cnt -  Get Frame Preemption Statistics counter
+ * @ndev: Pointer to the net_device structure
+ * @useraddr: return value, containing counters value
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_preemption_cnt(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct emac_pmac_stats stats;
+
+	statistic_cnts(ndev, &stats.emac,
+		       sizeof(struct statistics_counters) / 4,
+		       RX_BYTES_EMAC_REG);
+
+	stats.preemp_en = axienet_ior(lp, PREEMPTION_ENABLE_REG);
+	if (stats.preemp_en) {
+		statistic_cnts(ndev, &stats.pmac.sts,
+			       sizeof(struct statistics_counters) / 4,
+			       RX_BYTES_PMAC_REG);
+		statistic_cnts(ndev, &stats.pmac.merge,
+			       sizeof(struct mac_merge_counters) / 4,
+			       MAC_MERGE_HOLD_COUNT_REG);
+	}
+
+	if (copy_to_user(useraddr, &stats, sizeof(struct emac_pmac_stats)))
+		return -EFAULT;
+	return 0;
+}
+
+/**
+ * axienet_qbu_user_override -  Configure QBU user override register
+ * @ndev: Pointer to the net_device structure
+ * @useraddr: Value to be programmed
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_qbu_user_override(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct qbu_prog data;
+	u32 value;
+
+	if (copy_from_user(&data, useraddr, sizeof(struct qbu_prog)))
+		return -EFAULT;
+
+	value = axienet_ior(lp, QBU_USER_OVERRIDE_REG);
+
+	if (data.set & QBU_WINDOW) {
+		if (data.user.hold_rel_window) {
+			value |= USER_HOLD_REL_ENABLE_VALUE;
+			value |= HOLD_REL_WINDOW_OVERRIDE;
+		} else {
+			value &= ~(USER_HOLD_REL_ENABLE_VALUE);
+			value &= ~(HOLD_REL_WINDOW_OVERRIDE);
+		}
+	}
+	if (data.set & QBU_GUARD_BAND) {
+		if (data.user.guard_band)
+			value |= GUARD_BAND_OVERRUN_CNT_INC_OVERRIDE;
+		else
+			value &= ~(GUARD_BAND_OVERRUN_CNT_INC_OVERRIDE);
+	}
+	if (data.set & QBU_HOLD_TIME) {
+		if (data.user.hold_time_override) {
+			value |= HOLD_TIME_OVERRIDE;
+			value &= ~(USER_HOLD_TIME_MASK << USER_HOLD_TIME_SHIFT);
+			value |= data.user.user_hold_time <<
+					USER_HOLD_TIME_SHIFT;
+		} else {
+			value &= ~(HOLD_TIME_OVERRIDE);
+			value &= ~(USER_HOLD_TIME_MASK << USER_HOLD_TIME_SHIFT);
+		}
+	}
+	if (data.set & QBU_REL_TIME) {
+		if (data.user.rel_time_override) {
+			value |= REL_TIME_OVERRIDE;
+			value &= ~(USER_REL_TIME_MASK << USER_REL_TIME_SHIFT);
+			value |= data.user.user_rel_time << USER_REL_TIME_SHIFT;
+		} else {
+			value &= ~(REL_TIME_OVERRIDE);
+			value &= ~(USER_REL_TIME_MASK << USER_REL_TIME_SHIFT);
+		}
+	}
+
+	axienet_iow(lp, QBU_USER_OVERRIDE_REG, value);
+	return 0;
+}
+
+/**
+ * axienet_qbu_sts -  Get QBU Core status
+ * @ndev: Pointer to the net_device structure
+ * @useraddr: return value, containing QBU core status value
+ * Return: 0 on success, Non-zero error value on failure
+ */
+int axienet_qbu_sts(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct qbu_all_status status;
+	u32 value = 0;
+
+	value = axienet_ior(lp, QBU_USER_OVERRIDE_REG);
+	status.prog.hold_rel_window = (value & USER_HOLD_REL_ENABLE_VALUE)
+					? 1 : 0;
+	status.prog.guard_band = (value & GUARD_BAND_OVERRUN_CNT_INC_OVERRIDE)
+					? 1 : 0;
+	status.prog.user_hold_time = (value >> USER_HOLD_TIME_SHIFT) &
+					USER_HOLD_TIME_MASK;
+	status.prog.user_rel_time = (value >> USER_REL_TIME_SHIFT) &
+					USER_REL_TIME_MASK;
+
+	value = axienet_ior(lp, QBU_CORE_STS_REG);
+	status.core.hold_time = (value >> HOLD_TIME_STS_SHIFT) &
+					HOLD_TIME_STS_MASK;
+	status.core.rel_time = (value >> REL_TIME_STS_SHIFT) &
+					REL_TIME_STS_MASK;
+	status.core.hold_rel_en = (value & HOLD_REL_ENABLE_STS) ? 1 : 0;
+	status.core.pmac_hold_req = value & PMAC_HOLD_REQ_STS;
+
+	if (copy_to_user(useraddr, &status, sizeof(struct qbu_all_status)))
+		return -EFAULT;
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_preemption.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_preemption.h
@@ -0,0 +1,177 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Xilinx TSN QBU/QBR - Frame Preemption header
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * Author: Priyadarshini Babu <priyadar@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef XILINX_TSN_PREEMPTION_H
+#define XILINX_TSN_PREEMPTION_H
+
+#define PREEMPTION_ENABLE_REG			0x00000440
+#define PREEMPTION_CTRL_STS_REG			0x00000444
+#define QBU_USER_OVERRIDE_REG			0x00000448
+#define QBU_CORE_STS_REG			0x0000044c
+#define RX_BYTES_EMAC_REG			0x00000200
+#define RX_BYTES_PMAC_REG			0x00000800
+#define MAC_MERGE_HOLD_COUNT_REG		0x00000910
+#define MAC_MERGE_FRAG_COUNT_TX_REG		0x00000918
+#define MAC_MERGE_FRAME_ASSEMBLY_OK_COUNT_RX_REG	0x00000920
+#define MAC_MERGE_FRAME_ASSEMBLY_ERROR_COUNT_REG	0x00000928
+#define MAC_MERGE_FRAME_SMD_ERROR_COUNT_REG		0x00000930
+#define MAC_MERGE_FRAG_COUNT_RX_REG			0x00000938
+
+#define PREEMPTION_ENABLE			BIT(0)
+#define PREEMPTION_SUPPORT			BIT(15)
+
+#define TX_PREEMPTION_STS			BIT(31)
+#define MAC_MERGE_TX_VERIFY_STS_MASK		0x7
+#define MAC_MERGE_TX_VERIFY_STS_SHIFT		24
+#define VERIFY_TIMER_VALUE_MASK			0x7F
+#define VERIFY_TIMER_VALUE_SHIFT		8
+#define ADDITIONAL_FRAG_SIZE_MASK		0x3
+#define ADDITIONAL_FRAG_SIZE_SHIFT		4
+#define DISABLE_PREEMPTION_VERIFY		BIT(0)
+#define MAX_VERIFY_TIME				0x7F	/* 7-bit field */
+
+#define USER_HOLD_REL_ENABLE_VALUE		BIT(31)
+#define USER_HOLD_TIME_MASK			0x1FF
+#define USER_HOLD_TIME_SHIFT			16
+#define USER_REL_TIME_MASK			0x3F
+#define USER_REL_TIME_SHIFT			8
+#define GUARD_BAND_OVERRUN_CNT_INC_OVERRIDE	BIT(3)
+#define HOLD_REL_WINDOW_OVERRIDE		BIT(2)
+#define HOLD_TIME_OVERRIDE			BIT(1)
+#define REL_TIME_OVERRIDE			BIT(0)
+
+#define HOLD_REL_ENABLE_STS			BIT(31)
+#define HOLD_TIME_STS_MASK			0x1FF
+#define HOLD_TIME_STS_SHIFT			16
+#define REL_TIME_STS_MASK			0x3F
+#define REL_TIME_STS_SHIFT			8
+#define PMAC_HOLD_REQ_STS			BIT(0)
+
+struct preempt_ctrl_sts {
+	u8 tx_preemp_sts;
+	u8 mac_tx_verify_sts;
+	u8 verify_timer_value;
+	u8 additional_frag_size;
+	u8 disable_preemp_verify;
+};
+
+struct qbu_prog_override {
+	u8 enable_value:1;
+	u16 user_hold_time:9;
+	u8 user_rel_time:6;
+	u8 guard_band:1;
+	u8 hold_rel_window:1;
+	u8 hold_time_override:1;
+	u8 rel_time_override:1;
+} __packed;
+
+struct qbu_prog {
+	struct qbu_prog_override user;
+	u8 set;
+};
+
+#define QBU_WINDOW BIT(0)
+#define QBU_GUARD_BAND BIT(1)
+#define QBU_HOLD_TIME BIT(2)
+#define QBU_REL_TIME BIT(3)
+
+struct qbu_core_status {
+	u16 hold_time;
+	u8 rel_time;
+	u8 hold_rel_en:1;
+	u8 pmac_hold_req:1;
+} __packed;
+
+struct qbu_all_status {
+	struct qbu_prog_override prog;
+	struct qbu_core_status core;
+};
+
+struct cnt_64 {
+	unsigned int msb;
+	unsigned int lsb;
+};
+
+union static_cntr {
+	u64 cnt;
+	struct cnt_64 word;
+};
+
+struct mac_merge_counters {
+	union static_cntr tx_hold_cnt;
+	union static_cntr tx_frag_cnt;
+	union static_cntr rx_assembly_ok_cnt;
+	union static_cntr rx_assembly_err_cnt;
+	union static_cntr rx_smd_err_cnt;
+	union static_cntr rx_frag_cnt;
+};
+
+struct statistics_counters {
+	union static_cntr rx_bytes_cnt;
+	union static_cntr tx_bytes_cnt;
+	union static_cntr undersize_frames_cnt;
+	union static_cntr frag_frames_cnt;
+	union static_cntr rx_64_bytes_frames_cnt;
+	union static_cntr rx_65_127_bytes_frames_cnt;
+	union static_cntr rx_128_255_bytes_frames_cnt;
+	union static_cntr rx_256_511_bytes_frames_cnt;
+	union static_cntr rx_512_1023_bytes_frames_cnt;
+	union static_cntr rx_1024_max_frames_cnt;
+	union static_cntr rx_oversize_frames_cnt;
+	union static_cntr tx_64_bytes_frames_cnt;
+	union static_cntr tx_65_127_bytes_frames_cnt;
+	union static_cntr tx_128_255_bytes_frames_cnt;
+	union static_cntr tx_256_511_bytes_frames_cnt;
+	union static_cntr tx_512_1023_bytes_frames_cnt;
+	union static_cntr tx_1024_max_frames_cnt;
+	union static_cntr tx_oversize_frames_cnt;
+	union static_cntr rx_good_frames_cnt;
+	union static_cntr rx_fcs_err_cnt;
+	union static_cntr rx_good_broadcast_frames_cnt;
+	union static_cntr rx_good_multicast_frames_cnt;
+	union static_cntr rx_good_control_frames_cnt;
+	union static_cntr rx_out_of_range_err_cnt;
+	union static_cntr rx_good_vlan_frames_cnt;
+	union static_cntr rx_good_pause_frames_cnt;
+	union static_cntr rx_bad_opcode_frames_cnt;
+	union static_cntr tx_good_frames_cnt;
+	union static_cntr tx_good_broadcast_frames_cnt;
+	union static_cntr tx_good_multicast_frames_cnt;
+	union static_cntr tx_underrun_err_cnt;
+	union static_cntr tx_good_control_frames_cnt;
+	union static_cntr tx_good_vlan_frames_cnt;
+	union static_cntr tx_good_pause_frames_cnt;
+};
+
+struct pmac_counters {
+	struct statistics_counters sts;
+	struct mac_merge_counters merge;
+};
+
+struct emac_pmac_stats {
+	u8 preemp_en;
+	struct statistics_counters emac;
+	struct pmac_counters pmac;
+};
+
+struct preempt_status {
+	u8 preemp_en;
+	u8 preemp_sup;
+	struct preempt_ctrl_sts ctrl;
+};
+#endif /* XILINX_TSN_PREEMPTION_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_ptp.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_ptp.h
@@ -0,0 +1,89 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Xilinx TSN PTP header
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * Author: Syed S <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _TSN_PTP_H_
+#define _TSN_PTP_H_
+
+#define PTP_HW_TSTAMP_SIZE  8   /* 64 bit timestamp */
+#define PTP_RX_HWBUF_SIZE   256
+#define PTP_RX_FRAME_SIZE   252
+#define PTP_HW_TSTAMP_OFFSET (PTP_RX_HWBUF_SIZE - PTP_HW_TSTAMP_SIZE)
+
+#define PTP_MSG_TYPE_MASK				BIT(3)
+#define PTP_TYPE_SYNC                                   0x0
+#define PTP_TYPE_FOLLOW_UP                              0x8
+#define PTP_TYPE_PDELAYREQ                              0x2
+#define PTP_TYPE_PDELAYRESP                             0x3
+#define PTP_TYPE_PDELAYRESP_FOLLOW_UP                   0xA
+#define PTP_TYPE_ANNOUNCE                               0xB
+#define PTP_TYPE_SIGNALING                              0xC
+
+#define PTP_TX_CONTROL_OFFSET		0x00012000 /**< Tx PTP Control Reg */
+#define PTP_RX_CONTROL_OFFSET		0x00012004 /**< Rx PTP Control Reg */
+#define RX_FILTER_CONTROL		0x00012008 /**< Rx Filter Ctrl Reg */
+
+#define PTP_RX_BASE_OFFSET		0x00010000
+#define PTP_RX_CONTROL_OFFSET		0x00012004 /**< Rx PTP Control Reg */
+#define PTP_RX_PACKET_FIELD_MASK	0x00000F00
+#define PTP_RX_PACKET_CLEAR		0x00000001
+
+#define PTP_TX_BUFFER_OFFSET(index)	   (0x00011000 + (index) * 0x100)
+
+#define PTP_TX_CMD_FIELD_LEN			8
+#define PTP_TX_CMD_1STEP_SHIFT			BIT(16)
+#define PTP_TX_BUFFER_CMD2_FIELD		0x4
+
+#define PTP_TX_SYNC_OFFSET                 0x00011000
+#define PTP_TX_FOLLOW_UP_OFFSET            0x00011100
+#define PTP_TX_PDELAYREQ_OFFSET            0x00011200
+#define PTP_TX_PDELAYRESP_OFFSET           0x00011300
+#define PTP_TX_PDELAYRESP_FOLLOW_UP_OFFSET 0x00011400
+#define PTP_TX_ANNOUNCE_OFFSET             0x00011500
+#define PTP_TX_SIGNALING_OFFSET		   0x00011600
+#define PTP_TX_GENERIC_OFFSET		   0x00011700
+#define PTP_TX_SEND_SYNC_FRAME_MASK                     0x00000001
+#define PTP_TX_SEND_FOLLOWUP_FRAME_MASK                 0x00000002
+#define PTP_TX_SEND_PDELAYREQ_FRAME_MASK                0x00000004
+#define PTP_TX_SEND_PDELAYRESP_FRAME_MASK               0x00000008
+#define PTP_TX_SEND_PDELAYRESPFOLLOWUP_FRAME_MASK       0x00000010
+#define PTP_TX_SEND_ANNOUNCE_FRAME_MASK                 0x00000020
+#define PTP_TX_SEND_FRAME6_BIT_MASK                     0x00000040
+#define PTP_TX_SEND_FRAME7_BIT_MASK                     0x00000080
+#define PTP_TX_FRAME_WAITING_MASK			0x0000ff00
+#define PTP_TX_FRAME_WAITING_SHIFT			8
+#define PTP_TX_WAIT_SYNC_FRAME_MASK                     0x00000100
+#define PTP_TX_WAIT_FOLLOWUP_FRAME_MASK                 0x00000200
+#define PTP_TX_WAIT_PDELAYREQ_FRAME_MASK                0x00000400
+#define PTP_TX_WAIT_PDELAYRESP_FRAME_MASK               0x00000800
+#define PTP_TX_WAIT_PDELAYRESPFOLLOWUP_FRAME_MASK       0x00001000
+#define PTP_TX_WAIT_ANNOUNCE_FRAME_MASK                 0x00002000
+#define PTP_TX_WAIT_FRAME6_BIT_MASK                     0x00004000
+#define PTP_TX_WAIT_FRAME7_BIT_MASK                     0x00008000
+#define PTP_TX_WAIT_ALL_FRAMES_MASK                     0x0000FF00
+#define PTP_TX_PACKET_FIELD_MASK                        0x00070000
+#define PTP_TX_PACKET_FIELD_SHIFT                       16
+/* 1-step Correction Field offset 802.1 ASrev */
+#define PTP_CRCT_FIELD_OFFSET				22
+/* 1-step Time Of Day offset 1588-2008 */
+#define PTP_TOD_FIELD_OFFSET				48
+
+int axienet_ptp_xmit(struct sk_buff *skb, struct net_device *ndev);
+irqreturn_t axienet_ptp_rx_irq(int irq, void *_ndev);
+irqreturn_t axienet_ptp_tx_irq(int irq, void *_ndev);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_ptp_clock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_ptp_clock.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN PTP protocol clock Controller module.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Syed S <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/kernel.h>
+#include <linux/ptp_clock_kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of_irq.h>
+#include "xilinx_tsn_timer.h"
+
+struct xlnx_ptp_timer {
+	struct                 device *dev;
+	void __iomem          *baseaddr;
+	struct ptp_clock      *ptp_clock;
+	struct ptp_clock_info  ptp_clock_info;
+	spinlock_t             reg_lock; /* ptp timer lock */
+	int                    irq;
+	int                    pps_enable;
+	int                    countpulse;
+};
+
+static void xlnx_tod_read(struct xlnx_ptp_timer *timer, struct timespec64 *ts)
+{
+	u32 sec, nsec;
+
+	nsec = in_be32(timer->baseaddr + XTIMER1588_CURRENT_RTC_NS);
+	sec = in_be32(timer->baseaddr + XTIMER1588_CURRENT_RTC_SEC_L);
+
+	ts->tv_sec = sec;
+	ts->tv_nsec = nsec;
+}
+
+static void xlnx_rtc_offset_write(struct xlnx_ptp_timer *timer,
+				  const struct timespec64 *ts)
+{
+	pr_debug("%s: sec: %lld nsec: %ld\n", __func__, ts->tv_sec, ts->tv_nsec);
+
+	out_be32((timer->baseaddr + XTIMER1588_RTC_OFFSET_SEC_H), 0);
+	out_be32((timer->baseaddr + XTIMER1588_RTC_OFFSET_SEC_L),
+		 (ts->tv_sec));
+	out_be32((timer->baseaddr + XTIMER1588_RTC_OFFSET_NS), ts->tv_nsec);
+}
+
+static void xlnx_rtc_offset_read(struct xlnx_ptp_timer *timer,
+				 struct timespec64 *ts)
+{
+	ts->tv_sec = in_be32(timer->baseaddr + XTIMER1588_RTC_OFFSET_SEC_L);
+	ts->tv_nsec = in_be32(timer->baseaddr + XTIMER1588_RTC_OFFSET_NS);
+}
+
+/* PTP clock operations
+ */
+static int xlnx_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						    ptp_clock_info);
+
+	int neg_adj = 0;
+	u64 freq;
+	u32 diff, incval;
+
+	/* This number should be replaced by a call to get the frequency
+	 * from the device-tree. Currently assumes 125MHz
+	 */
+	incval = 0x800000;
+	/* for 156.25 MHZ Ref clk the value is  incval = 0x800000; */
+
+	if (ppb < 0) {
+		neg_adj = 1;
+		ppb = -ppb;
+	}
+
+	freq = incval;
+	freq *= ppb;
+	diff = div_u64(freq, 1000000000ULL);
+
+	pr_debug("%s: adj: %d ppb: %d\n", __func__, diff, ppb);
+
+	incval = neg_adj ? (incval - diff) : (incval + diff);
+	out_be32((timer->baseaddr + XTIMER1588_RTC_INCREMENT), incval);
+	return 0;
+}
+
+static int xlnx_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+	unsigned long flags;
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						    ptp_clock_info);
+	struct timespec64 now, then = ns_to_timespec64(delta);
+
+	spin_lock_irqsave(&timer->reg_lock, flags);
+
+	xlnx_rtc_offset_read(timer, &now);
+
+	now = timespec64_add(now, then);
+
+	xlnx_rtc_offset_write(timer, (const struct timespec64 *)&now);
+	spin_unlock_irqrestore(&timer->reg_lock, flags);
+
+	return 0;
+}
+
+static int xlnx_ptp_gettime(struct ptp_clock_info *ptp, struct timespec64 *ts)
+{
+	unsigned long flags;
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						    ptp_clock_info);
+	spin_lock_irqsave(&timer->reg_lock, flags);
+
+	xlnx_tod_read(timer, ts);
+
+	spin_unlock_irqrestore(&timer->reg_lock, flags);
+	return 0;
+}
+
+/**
+ * xlnx_ptp_settime - Set the current time on the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec64 containing the new time for the cycle counter
+ *
+ * Return: 0 in all cases.
+ *
+ * The seconds register is written first, then the nanosecond
+ * The hardware loads the entire new value when a nanosecond register
+ * is written
+ **/
+static int xlnx_ptp_settime(struct ptp_clock_info *ptp,
+			    const struct timespec64 *ts)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						    ptp_clock_info);
+	struct timespec64 delta, tod;
+	struct timespec64 offset;
+	unsigned long flags;
+
+	spin_lock_irqsave(&timer->reg_lock, flags);
+
+	/* First zero the offset */
+	offset.tv_sec = 0;
+	offset.tv_nsec = 0;
+	xlnx_rtc_offset_write(timer, &offset);
+
+	/* Get the current timer value */
+	xlnx_tod_read(timer, &tod);
+
+	/* Subtract the current reported time from our desired time */
+	delta = timespec64_sub(*ts, tod);
+
+	/* Don't write a negative offset */
+	if (delta.tv_sec <= 0) {
+		delta.tv_sec = 0;
+		if (delta.tv_nsec < 0)
+			delta.tv_nsec = 0;
+	}
+
+	xlnx_rtc_offset_write(timer, &delta);
+	spin_unlock_irqrestore(&timer->reg_lock, flags);
+	return 0;
+}
+
+static int xlnx_ptp_enable(struct ptp_clock_info *ptp,
+			   struct ptp_clock_request *rq, int on)
+{
+	struct xlnx_ptp_timer *timer = container_of(ptp, struct xlnx_ptp_timer,
+						    ptp_clock_info);
+
+	switch (rq->type) {
+	case PTP_CLK_REQ_PPS:
+		timer->pps_enable = 1;
+		return 0;
+	default:
+		break;
+	}
+
+	return -EOPNOTSUPP;
+}
+
+static struct ptp_clock_info xlnx_ptp_clock_info = {
+	.owner    = THIS_MODULE,
+	.name     = "Xilinx Timer",
+	.max_adj  = 999999999,
+	.n_ext_ts	= 0,
+	.pps      = 1,
+	.adjfreq  = xlnx_ptp_adjfreq,
+	.adjtime  = xlnx_ptp_adjtime,
+	.gettime64  = xlnx_ptp_gettime,
+	.settime64 = xlnx_ptp_settime,
+	.enable   = xlnx_ptp_enable,
+};
+
+/* module operations */
+
+/**
+ * xlnx_ptp_timer_isr - Interrupt Service Routine
+ * @irq:               IRQ number
+ * @priv:              pointer to the timer structure
+ *
+ * Returns: IRQ_HANDLED for all cases
+ *
+ * Handles the timer interrupt. The timer interrupt fires 128 times per
+ * secound. When our count reaches 128 emit a PTP_CLOCK_PPS event
+ */
+static irqreturn_t xlnx_ptp_timer_isr(int irq, void *priv)
+{
+	struct xlnx_ptp_timer *timer = (struct xlnx_ptp_timer *)priv;
+	struct ptp_clock_event event;
+
+	event.type = PTP_CLOCK_PPS;
+	++timer->countpulse;
+	if (timer->countpulse >= PULSESIN1PPS) {
+		timer->countpulse = 0;
+		if (timer->ptp_clock && timer->pps_enable)
+			ptp_clock_event(timer->ptp_clock, &event);
+	}
+	out_be32((timer->baseaddr + XTIMER1588_INTERRUPT),
+		 (1 << XTIMER1588_INT_SHIFT));
+
+	return IRQ_HANDLED;
+}
+
+int axienet_ptp_timer_remove(void *priv)
+{
+	struct xlnx_ptp_timer *timer = (struct xlnx_ptp_timer *)priv;
+
+	free_irq(timer->irq, (void *)timer);
+
+	axienet_phc_index = -1;
+	if (timer->ptp_clock) {
+		ptp_clock_unregister(timer->ptp_clock);
+		timer->ptp_clock = NULL;
+	}
+	kfree(timer);
+	return 0;
+}
+
+int axienet_get_phc_index(void *priv)
+{
+	struct xlnx_ptp_timer *timer = (struct xlnx_ptp_timer *)priv;
+
+	if (timer->ptp_clock)
+		return ptp_clock_index(timer->ptp_clock);
+	else
+		return -1;
+}
+
+void *axienet_ptp_timer_probe(void __iomem *base, struct platform_device *pdev)
+{
+	struct xlnx_ptp_timer *timer;
+	struct timespec64 ts;
+	int err = 0;
+
+	timer = kzalloc(sizeof(*timer), GFP_KERNEL);
+	if (!timer)
+		return NULL;
+
+	timer->baseaddr = base;
+
+	timer->irq = platform_get_irq_byname(pdev, "interrupt_ptp_timer");
+
+	if (timer->irq < 0) {
+		timer->irq = platform_get_irq_byname(pdev, "rtc_irq");
+		if (timer->irq > 0) {
+			pr_err("ptp timer interrupt name 'rtc_irq' is deprecated\n");
+		} else {
+			pr_err("ptp timer interrupt not found\n");
+			kfree(timer);
+			return NULL;
+		}
+	}
+	spin_lock_init(&timer->reg_lock);
+
+	timer->ptp_clock_info = xlnx_ptp_clock_info;
+
+	timer->ptp_clock = ptp_clock_register(&timer->ptp_clock_info,
+					      &pdev->dev);
+
+	if (IS_ERR(timer->ptp_clock)) {
+		err = PTR_ERR(timer->ptp_clock);
+		pr_debug("Failed to register ptp clock\n");
+		goto out;
+	}
+
+	axienet_phc_index = ptp_clock_index(timer->ptp_clock);
+
+	ts = ktime_to_timespec64(ktime_get_real());
+
+	xlnx_ptp_settime(&timer->ptp_clock_info, &ts);
+
+	/* Enable interrupts */
+	err = request_irq(timer->irq,
+			  xlnx_ptp_timer_isr,
+			  0,
+			  "ptp_rtc",
+			  (void *)timer);
+	if (err)
+		goto err_irq;
+
+	return timer;
+
+err_irq:
+	ptp_clock_unregister(timer->ptp_clock);
+out:
+	timer->ptp_clock = NULL;
+	return NULL;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_ptp_xmit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_ptp_xmit.c
@@ -0,0 +1,370 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN PTP transfer protocol module.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Syed S <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_ptp.h"
+#include "xilinx_tsn_timer.h"
+#include <linux/ptp_classify.h>
+
+#define PTP_ONE_SECOND            1000000000    /**< Value in ns */
+
+#define msg_type_string(type) \
+	((type) == PTP_TYPE_SYNC) ? "SYNC" : \
+	((type) == PTP_TYPE_FOLLOW_UP)		  ? "FOLLOW_UP" : \
+	((type) == PTP_TYPE_PDELAYREQ)		  ? "PDELAY_REQ" : \
+	((type) == PTP_TYPE_PDELAYRESP)		  ? "PDELAY_RESP" : \
+	((type) == PTP_TYPE_PDELAYRESP_FOLLOW_UP) ? "PDELAY_RESP_FOLLOW_UP" : \
+	((type) == PTP_TYPE_ANNOUNCE)		  ? "ANNOUNCE" : \
+	"UNKNOWN"
+
+/**
+ * memcpy_fromio_32 - copy ptp buffer from HW
+ * @lp:		Pointer to axienet local structure
+ * @offset:	Offset in the PTP buffer
+ * @data:	Destination buffer
+ * @len:	Len to copy
+ *
+ * This functions copies the data from PTP buffer to destination data buffer
+ */
+static void memcpy_fromio_32(struct axienet_local *lp,
+			     unsigned long offset, u8 *data, size_t len)
+{
+	while (len >= 4) {
+		*(u32 *)data = axienet_ior(lp, offset);
+		len -= 4;
+		offset += 4;
+		data += 4;
+	}
+
+	if (len > 0) {
+		u32 leftover = axienet_ior(lp, offset);
+		u8 *src = (u8 *)&leftover;
+
+		while (len) {
+			*data++ = *src++;
+			len--;
+		}
+	}
+}
+
+/**
+ * memcpy_toio_32 - copy ptp buffer from HW
+ * @lp:		Pointer to axienet local structure
+ * @offset:	Offset in the PTP buffer
+ * @data:	Source data
+ * @len:	Len to copy
+ *
+ * This functions copies the source data to destination ptp buffer
+ */
+static void memcpy_toio_32(struct axienet_local *lp,
+			   unsigned long offset, u8 *data, size_t len)
+{
+	while (len >= 4) {
+		axienet_iow(lp, offset, *(u32 *)data);
+		len -= 4;
+		offset += 4;
+		data += 4;
+	}
+
+	if (len > 0) {
+		u32 leftover = 0;
+		u8 *dest = (u8 *)&leftover;
+
+		while (len) {
+			*dest++ = *data++;
+			len--;
+		}
+		axienet_iow(lp, offset, leftover);
+	}
+}
+
+static int is_sync(struct sk_buff *skb)
+{
+	u8 *msg_type;
+
+	msg_type = (u8 *)skb->data + ETH_HLEN;
+
+	return (*msg_type & 0xf) == PTP_TYPE_SYNC;
+}
+
+/**
+ * axienet_ptp_xmit - xmit skb using PTP HW
+ * @skb:	sk_buff pointer that contains data to be Txed.
+ * @ndev:	Pointer to net_device structure.
+ *
+ * Return: NETDEV_TX_OK, on success
+ *	    NETDEV_TX_BUSY, if any of the descriptors are not free
+ *
+ * This function is called to transmit a PTP skb. The function uses
+ * the free PTP TX buffer entry and sends the frame
+ */
+int axienet_ptp_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	u8 msg_type;
+	struct axienet_local *lp = netdev_priv(ndev);
+	unsigned long flags;
+	u8 tx_frame_waiting;
+	u8 free_index;
+	u32 cmd1_field = 0;
+	u32 cmd2_field = 0;
+
+	msg_type  = *(u8 *)(skb->data + ETH_HLEN);
+
+	pr_debug("  -->XMIT: protocol: %x message: %s frame_len: %d\n",
+		 skb->protocol,
+		 msg_type_string(msg_type & 0xf), skb->len);
+
+	tx_frame_waiting =  (axienet_ior(lp, PTP_TX_CONTROL_OFFSET) &
+				PTP_TX_FRAME_WAITING_MASK) >>
+				PTP_TX_FRAME_WAITING_SHIFT;
+
+	/* we reached last frame */
+	if (tx_frame_waiting & (1 << 7)) {
+		if (!netif_queue_stopped(ndev))
+			netif_stop_queue(ndev);
+		pr_debug("tx_frame_waiting: %d\n", tx_frame_waiting);
+		return NETDEV_TX_BUSY;
+	}
+
+	/* go to next available slot */
+	free_index  = fls(tx_frame_waiting);
+
+	/* write the len */
+	if (lp->ptp_ts_type == HWTSTAMP_TX_ONESTEP_SYNC &&
+	    is_sync(skb)) {
+		/* enable 1STEP SYNC */
+		cmd1_field |= PTP_TX_CMD_1STEP_SHIFT;
+		cmd2_field |= PTP_TOD_FIELD_OFFSET;
+	}
+
+	cmd1_field |= skb->len;
+
+	axienet_iow(lp, PTP_TX_BUFFER_OFFSET(free_index), cmd1_field);
+	axienet_iow(lp, PTP_TX_BUFFER_OFFSET(free_index) +
+			PTP_TX_BUFFER_CMD2_FIELD, cmd2_field);
+	memcpy_toio_32(lp,
+		       (PTP_TX_BUFFER_OFFSET(free_index) +
+			PTP_TX_CMD_FIELD_LEN),
+		       skb->data, skb->len);
+
+	/* send the frame */
+	axienet_iow(lp, PTP_TX_CONTROL_OFFSET, (1 << free_index));
+
+	if (lp->ptp_ts_type != HWTSTAMP_TX_ONESTEP_SYNC ||
+	    (!is_sync(skb))) {
+		spin_lock_irqsave(&lp->ptp_tx_lock, flags);
+		skb->cb[0] = free_index;
+		skb_queue_tail(&lp->ptp_txq, skb);
+
+		if (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)
+			skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+
+		skb_tx_timestamp(skb);
+		spin_unlock_irqrestore(&lp->ptp_tx_lock, flags);
+	}
+	return NETDEV_TX_OK;
+}
+
+/**
+ * axienet_set_timestamp - timestamp skb with HW timestamp
+ * @lp:		Pointer to axienet local structure
+ * @hwtstamps:  Pointer to skb timestamp structure
+ * @offset:	offset of the timestamp in the PTP buffer
+ *
+ * Return:	None.
+ *
+ */
+static void axienet_set_timestamp(struct axienet_local *lp,
+				  struct skb_shared_hwtstamps *hwtstamps,
+				  unsigned int offset)
+{
+	u32 captured_ns;
+	u32 captured_sec;
+
+	captured_ns = axienet_ior(lp, offset + 4);
+	captured_sec = axienet_ior(lp, offset);
+
+	/* Upper 32 bits contain s, lower 32 bits contain ns. */
+	hwtstamps->hwtstamp = ktime_set(captured_sec,
+					captured_ns);
+}
+
+/**
+ * axienet_ptp_recv - receive ptp buffer in skb from HW
+ * @ndev:	Pointer to net_device structure.
+ *
+ * This function is called from the ptp rx isr. It allocates skb, and
+ * copies the ptp rx buffer data to it and calls netif_rx for further
+ * processing.
+ *
+ */
+static void axienet_ptp_recv(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	unsigned long ptp_frame_base_addr = 0;
+	struct sk_buff *skb;
+	u16 msg_len;
+	u8 msg_type;
+	u32 bytes = 0;
+	u32 packets = 0;
+
+	pr_debug("%s:\n ", __func__);
+
+	while (((lp->ptp_rx_hw_pointer & 0xf) !=
+		 (lp->ptp_rx_sw_pointer & 0xf))) {
+		skb = netdev_alloc_skb(ndev, PTP_RX_FRAME_SIZE);
+
+		lp->ptp_rx_sw_pointer += 1;
+
+		ptp_frame_base_addr = PTP_RX_BASE_OFFSET +
+				   ((lp->ptp_rx_sw_pointer & 0xf) *
+							PTP_RX_HWBUF_SIZE);
+
+		memset(skb->data, 0x0, PTP_RX_FRAME_SIZE);
+
+		memcpy_fromio_32(lp, ptp_frame_base_addr, skb->data,
+				 PTP_RX_FRAME_SIZE);
+
+		msg_type  = *(u8 *)(skb->data + ETH_HLEN) & 0xf;
+		msg_len  = *(u16 *)(skb->data + ETH_HLEN + 2);
+
+		skb_put(skb, ntohs(msg_len) + ETH_HLEN);
+
+		bytes += skb->len;
+		packets++;
+
+		skb->protocol = eth_type_trans(skb, ndev);
+		skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+		pr_debug("  -->RECV: protocol: %x message: %s frame_len: %d\n",
+			 skb->protocol, msg_type_string(msg_type & 0xf),
+			 skb->len);
+		/* timestamp only event messages */
+		if (!(msg_type & PTP_MSG_TYPE_MASK)) {
+			axienet_set_timestamp(lp, skb_hwtstamps(skb),
+					      (ptp_frame_base_addr +
+					      PTP_HW_TSTAMP_OFFSET));
+		}
+
+		netif_rx(skb);
+	}
+	ndev->stats.rx_packets += packets;
+	ndev->stats.rx_bytes += bytes;
+}
+
+/**
+ * axienet_ptp_rx_irq - PTP RX ISR handler
+ * @irq:		irq number
+ * @_ndev:	net_device pointer
+ *
+ * Return:	IRQ_HANDLED for all cases.
+ */
+irqreturn_t axienet_ptp_rx_irq(int irq, void *_ndev)
+{
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	pr_debug("%s: received\n ", __func__);
+	lp->ptp_rx_hw_pointer = (axienet_ior(lp, PTP_RX_CONTROL_OFFSET)
+					& PTP_RX_PACKET_FIELD_MASK)  >> 8;
+
+	axienet_ptp_recv(ndev);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * axienet_tx_tstamp - timestamp skb on trasmit path
+ * @work:	Pointer to work_struct structure
+ *
+ * This adds TX timestamp to skb
+ */
+void axienet_tx_tstamp(struct work_struct *work)
+{
+	struct axienet_local *lp = container_of(work, struct axienet_local,
+			tx_tstamp_work);
+	struct net_device *ndev = lp->ndev;
+	struct skb_shared_hwtstamps hwtstamps;
+	struct sk_buff *skb;
+	unsigned long ts_reg_offset;
+	unsigned long flags;
+	u8 tx_packet;
+	u8 index;
+	u32 bytes = 0;
+	u32 packets = 0;
+
+	memset(&hwtstamps, 0, sizeof(struct skb_shared_hwtstamps));
+
+	spin_lock_irqsave(&lp->ptp_tx_lock, flags);
+
+	tx_packet =  (axienet_ior(lp, PTP_TX_CONTROL_OFFSET) &
+				PTP_TX_PACKET_FIELD_MASK) >>
+				PTP_TX_PACKET_FIELD_SHIFT;
+
+	while ((skb = __skb_dequeue(&lp->ptp_txq)) != NULL) {
+		index = skb->cb[0];
+
+		/* dequeued packet yet to be xmited? */
+		if (index > tx_packet) {
+			/* enqueue it back and break */
+			skb_queue_tail(&lp->ptp_txq, skb);
+			break;
+		}
+		/* time stamp reg offset */
+		ts_reg_offset = PTP_TX_BUFFER_OFFSET(index) +
+					PTP_HW_TSTAMP_OFFSET;
+
+		if (skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS) {
+			axienet_set_timestamp(lp, &hwtstamps, ts_reg_offset);
+			skb_tstamp_tx(skb, &hwtstamps);
+		}
+
+		bytes += skb->len;
+		packets++;
+		dev_kfree_skb_any(skb);
+	}
+	ndev->stats.tx_packets += packets;
+	ndev->stats.tx_bytes += bytes;
+
+	spin_unlock_irqrestore(&lp->ptp_tx_lock, flags);
+}
+
+/**
+ * axienet_ptp_tx_irq - PTP TX irq handler
+ * @irq:		irq number
+ * @_ndev:	net_device pointer
+ *
+ * Return:	IRQ_HANDLED for all cases.
+ *
+ */
+irqreturn_t axienet_ptp_tx_irq(int irq, void *_ndev)
+{
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	pr_debug("%s: got tx interrupt\n", __func__);
+
+	/* read ctrl register to clear the interrupt */
+	axienet_ior(lp, PTP_TX_CONTROL_OFFSET);
+
+	schedule_work(&lp->tx_tstamp_work);
+
+	netif_wake_queue(ndev);
+
+	return IRQ_HANDLED;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_qci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_qci.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN QCI Controller module.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "xilinx_tsn_switch.h"
+
+#define SMC_MODE_SHIFT				28
+#define	SMC_CBR_MASK				0x00FFFFFF
+#define	SMC_EBR_MASK				0x00FFFFFF
+#define IN_PORTID_MASK				0x3
+#define IN_PORT_SHIFT				14
+#define MAX_FR_SIZE_MASK			0x00000FFF
+
+#define GATE_ID_SHIFT				24
+#define METER_ID_SHIFT				8
+#define EN_METER_SHIFT				6
+#define ALLOW_STREM_SHIFT			5
+#define EN_PSFP_SHIFT				4
+#define WR_OP_TYPE_MASK				0x3
+#define WR_OP_TYPE_SHIFT			2
+#define OP_TYPE_SHIFT				1
+#define PSFP_EN_CONTROL_MASK			0x1
+
+/**
+ * psfp_control - Configure thr control for PSFP
+ * @data:	Value to be programmed
+ */
+void psfp_control(struct psfp_config data)
+{
+	u32 mask;
+	u32 timeout = 20000;
+
+	mask = data.gate_id << GATE_ID_SHIFT;
+	mask |= data.meter_id << METER_ID_SHIFT;
+	mask |= data.en_meter << EN_METER_SHIFT;
+	mask |= data.allow_stream << ALLOW_STREM_SHIFT;
+	mask |= data.en_psfp << EN_PSFP_SHIFT;
+	mask |= (data.wr_op_type & WR_OP_TYPE_MASK) << WR_OP_TYPE_SHIFT;
+	mask |= data.op_type << OP_TYPE_SHIFT;
+	mask |= PSFP_EN_CONTROL_MASK;
+
+	axienet_iow(&lp, PSFP_CONTROL_OFFSET, mask);
+
+	/* wait for write to complete */
+	while ((axienet_ior(&lp, PSFP_CONTROL_OFFSET) &
+		PSFP_EN_CONTROL_MASK) && timeout)
+		timeout--;
+
+	if (!timeout)
+		pr_warn("PSFP control write took longer time!!");
+}
+
+/**
+ * get_stream_filter_config -  Get Stream Filter Configuration
+ * @data:	Value returned
+ */
+void get_stream_filter_config(struct stream_filter *data)
+{
+	u32 reg_val;
+
+	reg_val = axienet_ior(&lp, STREAM_FILTER_CONFIG_OFFSET);
+
+	data->max_fr_size = reg_val & MAX_FR_SIZE_MASK;
+	data->in_pid = (reg_val >> IN_PORT_SHIFT) & IN_PORTID_MASK;
+}
+
+/**
+ * config_stream_filter -  Configure Stream Filter Configuration
+ * @data:	Value to be programmed
+ */
+void config_stream_filter(struct stream_filter data)
+{
+	u32 mask;
+
+	mask = ((data.in_pid & IN_PORTID_MASK) << IN_PORT_SHIFT) |
+					(data.max_fr_size & MAX_FR_SIZE_MASK);
+	axienet_iow(&lp, STREAM_FILTER_CONFIG_OFFSET, mask);
+}
+
+/**
+ * get_meter_reg -  Read Stream Meter Configuration registers value
+ * @data:	Value returned
+ */
+void get_meter_reg(struct meter_config *data)
+{
+	u32 conf_r4;
+
+	data->cir = axienet_ior(&lp, STREAM_METER_CIR_OFFSET);
+	data->eir = axienet_ior(&lp, STREAM_METER_EIR_OFFSET);
+	data->cbr = axienet_ior(&lp, STREAM_METER_CBR_OFFSET) & SMC_CBR_MASK;
+	conf_r4 = axienet_ior(&lp, STREAM_METER_EBR_OFFSET);
+
+	data->ebr = conf_r4 & SMC_EBR_MASK;
+	data->mode = (conf_r4 & 0xF0000000) >> SMC_MODE_SHIFT;
+}
+
+/**
+ * program_meter_reg -  configure Stream Meter Configuration registers
+ * @data:	Value to be programmed
+ */
+void program_meter_reg(struct meter_config data)
+{
+	u32 conf_r4;
+
+	axienet_iow(&lp, STREAM_METER_CIR_OFFSET, data.cir);
+	axienet_iow(&lp, STREAM_METER_EIR_OFFSET, data.eir);
+	/* TODO: Check if this barrier is necessary */
+	wmb();
+	axienet_iow(&lp, STREAM_METER_CBR_OFFSET, data.cbr & SMC_CBR_MASK);
+
+	conf_r4 = (data.ebr & SMC_EBR_MASK) | (data.mode << SMC_MODE_SHIFT);
+	axienet_iow(&lp, STREAM_METER_EBR_OFFSET, conf_r4);
+}
+
+/**
+ * get_psfp_static_counter -  get memory static counters value
+ * @data  :	return value, containing counter value
+ */
+void get_psfp_static_counter(struct psfp_static_counter *data)
+{
+	int offset = (data->num) * 8;
+
+	data->psfp_fr_count.lsb = axienet_ior(&lp, TOTAL_PSFP_FRAMES_OFFSET +
+									offset);
+	data->psfp_fr_count.msb = axienet_ior(&lp, TOTAL_PSFP_FRAMES_OFFSET  +
+								offset + 0x4);
+
+	data->err_filter_ins_port.lsb = axienet_ior(&lp,
+						    FLTR_INGS_PORT_ERR_OFFSET + offset);
+	data->err_filter_ins_port.msb = axienet_ior(&lp,
+						    FLTR_INGS_PORT_ERR_OFFSET + offset + 0x4);
+
+	data->err_filtr_sdu.lsb = axienet_ior(&lp, FLTR_STDU_ERR_OFFSET +
+									offset);
+	data->err_filtr_sdu.msb = axienet_ior(&lp, FLTR_STDU_ERR_OFFSET +
+								offset + 0x4);
+
+	data->err_meter.lsb = axienet_ior(&lp, METER_ERR_OFFSET + offset);
+	data->err_meter.msb = axienet_ior(&lp, METER_ERR_OFFSET + offset + 0x4);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_shaper.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_shaper.c
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN QBV sheduler module.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Syed S <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_shaper.h"
+
+static inline int axienet_map_gs_to_hw(struct axienet_local *lp, u32 gs)
+{
+	u8 be_queue = 0;
+	u8 re_queue = 1;
+	u8 st_queue = 2;
+	unsigned int acl_bit_map = 0;
+
+	if (lp->num_tc == 2)
+		st_queue = 1;
+
+	if (gs & GS_BE_OPEN)
+		acl_bit_map |= (1 << be_queue);
+	if (gs & GS_ST_OPEN)
+		acl_bit_map |= (1 << st_queue);
+	if (lp->num_tc == 3 && (gs & GS_RE_OPEN))
+		acl_bit_map |= (1 << re_queue);
+
+	return acl_bit_map;
+}
+
+static int __axienet_set_schedule(struct net_device *ndev, struct qbv_info *qbv)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u16 i;
+	unsigned int acl_bit_map = 0;
+	u32 u_config_change = 0;
+
+	if (qbv->cycle_time == 0) {
+		/* clear the gate enable bit */
+		u_config_change &= ~CC_ADMIN_GATE_ENABLE_BIT;
+		/* open all the gates */
+		u_config_change |= CC_ADMIN_GATE_STATE_SHIFT;
+
+		axienet_qbv_iow(lp, CONFIG_CHANGE, u_config_change);
+
+		return 0;
+	}
+
+	if (axienet_qbv_ior(lp, PORT_STATUS) & 1) {
+		if (qbv->force) {
+			u_config_change &= ~CC_ADMIN_GATE_ENABLE_BIT;
+			axienet_qbv_iow(lp, CONFIG_CHANGE, u_config_change);
+		} else {
+			return -EALREADY;
+		}
+	}
+	/* write admin time */
+	axienet_qbv_iow(lp, ADMIN_CYCLE_TIME_DENOMINATOR,
+			qbv->cycle_time & CYCLE_TIME_DENOMINATOR_MASK);
+
+	axienet_qbv_iow(lp, ADMIN_BASE_TIME_NS, qbv->ptp_time_ns);
+
+	axienet_qbv_iow(lp, ADMIN_BASE_TIME_SEC,
+			qbv->ptp_time_sec & 0xFFFFFFFF);
+	axienet_qbv_iow(lp, ADMIN_BASE_TIME_SECS,
+			(qbv->ptp_time_sec >> 32) & BASE_TIME_SECS_MASK);
+
+	u_config_change = axienet_qbv_ior(lp, CONFIG_CHANGE);
+
+	u_config_change &= ~(CC_ADMIN_CTRL_LIST_LENGTH_MASK <<
+				CC_ADMIN_CTRL_LIST_LENGTH_SHIFT);
+	u_config_change |= (qbv->list_length & CC_ADMIN_CTRL_LIST_LENGTH_MASK)
+					<< CC_ADMIN_CTRL_LIST_LENGTH_SHIFT;
+
+	/* program each list */
+	for (i = 0; i < qbv->list_length; i++) {
+		acl_bit_map = axienet_map_gs_to_hw(lp, qbv->acl_gate_state[i]);
+		axienet_qbv_iow(lp,  ADMIN_CTRL_LIST(i),
+				(acl_bit_map & (ACL_GATE_STATE_MASK)) <<
+				ACL_GATE_STATE_SHIFT);
+
+	    /* set the time for each entry */
+	    axienet_qbv_iow(lp, ADMIN_CTRL_LIST_TIME(i),
+			    qbv->acl_gate_time[i] &
+			    CTRL_LIST_TIME_INTERVAL_MASK);
+	}
+
+	/* clear interrupt status */
+	axienet_qbv_iow(lp, INT_STATUS, 0);
+
+	/* kick in new config change */
+	u_config_change |= CC_ADMIN_CONFIG_CHANGE_BIT;
+
+	/* enable gate */
+	u_config_change |= CC_ADMIN_GATE_ENABLE_BIT;
+
+	/* start */
+	axienet_qbv_iow(lp, CONFIG_CHANGE, u_config_change);
+
+	return 0;
+}
+
+int axienet_set_schedule(struct net_device *ndev, void __user *useraddr)
+{
+	struct qbv_info *config;
+	int ret;
+
+	config = kmalloc(sizeof(*config), GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	if (copy_from_user(config, useraddr, sizeof(struct qbv_info))) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	pr_debug("setting new schedule\n");
+
+	ret = __axienet_set_schedule(ndev, config);
+out:
+	kfree(config);
+	return ret;
+}
+
+static int __axienet_get_schedule(struct net_device *ndev, struct qbv_info *qbv)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u16 i = 0;
+	u32 u_value = 0;
+
+	if (!(axienet_qbv_ior(lp, CONFIG_CHANGE) &
+			CC_ADMIN_GATE_ENABLE_BIT)) {
+		qbv->cycle_time = 0;
+		return 0;
+	}
+
+	u_value = axienet_qbv_ior(lp, GATE_STATE);
+	qbv->list_length = (u_value >> CC_ADMIN_CTRL_LIST_LENGTH_SHIFT) &
+				CC_ADMIN_CTRL_LIST_LENGTH_MASK;
+
+	u_value = axienet_qbv_ior(lp, OPER_CYCLE_TIME_DENOMINATOR);
+	qbv->cycle_time = u_value & CYCLE_TIME_DENOMINATOR_MASK;
+
+	u_value = axienet_qbv_ior(lp, OPER_BASE_TIME_NS);
+	qbv->ptp_time_ns = u_value & OPER_BASE_TIME_NS_MASK;
+
+	qbv->ptp_time_sec = axienet_qbv_ior(lp, OPER_BASE_TIME_SEC);
+	u_value = axienet_qbv_ior(lp, OPER_BASE_TIME_SECS);
+	qbv->ptp_time_sec |= (u64)(u_value & BASE_TIME_SECS_MASK) << 32;
+
+	for (i = 0; i < qbv->list_length; i++) {
+		u_value = axienet_qbv_ior(lp, OPER_CTRL_LIST(i));
+		qbv->acl_gate_state[i] = (u_value >> ACL_GATE_STATE_SHIFT) &
+					ACL_GATE_STATE_MASK;
+		/**
+		 * In 2Q system, the actual ST Gate state value is 2,
+		 * for user the ST Gate state value is always 4.
+		 */
+		if (lp->num_tc == 2 && qbv->acl_gate_state[i] == 2)
+			qbv->acl_gate_state[i] = 4;
+
+		u_value = axienet_qbv_ior(lp, OPER_CTRL_LIST_TIME(i));
+		qbv->acl_gate_time[i] = u_value & CTRL_LIST_TIME_INTERVAL_MASK;
+	}
+	return 0;
+}
+
+int axienet_get_schedule(struct net_device *ndev, void __user *useraddr)
+{
+	struct qbv_info *qbv;
+	int ret = 0;
+
+	qbv = kmalloc(sizeof(*qbv), GFP_KERNEL);
+	if (!qbv)
+		return -ENOMEM;
+
+	if (copy_from_user(qbv, useraddr, sizeof(struct qbv_info))) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	__axienet_get_schedule(ndev, qbv);
+
+	if (copy_to_user(useraddr, qbv, sizeof(struct qbv_info)))
+		ret = -EFAULT;
+out:
+	kfree(qbv);
+	return ret;
+}
+
+static irqreturn_t axienet_qbv_irq(int irq, void *_ndev)
+{
+	struct net_device *ndev = _ndev;
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	/* clear status */
+	axienet_qbv_iow(lp, INT_CLEAR, 0);
+
+	return IRQ_HANDLED;
+}
+
+int axienet_qbv_init(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int rc = 0;
+	static char irq_name[24];
+
+	if (lp->qbv_irq > 0) {
+		sprintf(irq_name, "%s_qbv", ndev->name);
+		rc = request_irq(lp->qbv_irq, axienet_qbv_irq, 0, irq_name,
+				 ndev);
+	}
+	return rc;
+}
+
+void axienet_qbv_remove(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	free_irq(lp->qbv_irq, ndev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_shaper.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_shaper.h
@@ -0,0 +1,137 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Xilinx TSN QBV scheduler header
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * Author: Syed S <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef XILINX_TSN_SHAPER_H
+#define XILINX_TSN_SHAPER_H
+
+/* 0x0		CONFIG_CHANGE
+ * 0x8		GATE_STATE
+ * 0x10		ADMIN_CTRL_LIST_LENGTH
+ * 0x18		ADMIN_CYCLE_TIME_DENOMINATOR
+ * 0x20         ADMIN_BASE_TIME_NS
+ * 0x24		ADMIN_BASE_TIME_SEC
+ * 0x28		ADMIN_BASE_TIME_SECS
+ * 0x30		INT_STAT
+ * 0x34		INT_EN
+ * 0x38		INT_CLR
+ * 0x3c		STATUS
+ * 0x40		CONFIG_CHANGE_TIME_NS
+ * 0x44		CONFIG_CHANGE_TIME_SEC
+ * 0x48		CONFIG_CHANGE_TIME_SECS
+ * 0x50		OPER_CTRL_LIST_LENGTH
+ * 0x58		OPER_CYCLE_TIME_DENOMINATOR
+ * 0x60		OPER_BASE_TIME_NS
+ * 0x64		OPER_BASE_TIME_SEC
+ * 0x68		OPER_BASE_TIME_SECS
+ * 0x6c		BE_XMIT_OVRRUN_CNT
+ * 0x74		RES_XMIT_OVRRUN_CNT
+ * 0x7c		ST_XMIT_OVRRUN_CNT
+ */
+
+#define CTRL_LIST_BASE			0x1000
+
+/* control list entries
+ * admin control list 0 : 31
+ * "Time interval between two gate entries" must be greater than
+ * "time required to transmit biggest supported frame" on that queue when
+ * the gate for the queue is going from open to close state.
+ */
+#define ADMIN_CTRL_LIST(n)		(CTRL_LIST_BASE + ((n) * 8))
+#define ACL_GATE_STATE_SHIFT		8
+#define ACL_GATE_STATE_MASK		0x7
+#define ADMIN_CTRL_LIST_TIME(n)		(ADMIN_CTRL_LIST(n) + 4)
+
+#define OPER_CTRL_LIST(n)		(CTRL_LIST_BASE + 0x800 + ((n) * 8))
+#define OPER_CTRL_LIST_TIME(n)		(OPER_CTRL_LIST(n) + 4)
+#define CTRL_LIST_TIME_INTERVAL_MASK	0xFFFFF
+
+#define CONFIG_CHANGE			0x0
+#define CC_ADMIN_GATE_STATE_SHIFT	0x7
+#define CC_ADMIN_GATE_STATE_MASK	(7)
+#define CC_ADMIN_CTRL_LIST_LENGTH_SHIFT	(8)
+#define CC_ADMIN_CTRL_LIST_LENGTH_MASK	(0x1FF)
+/* This request bit is set when all the related Admin* filelds are populated.
+ * This bit is set by S/W and clear by core when core start with new schedule.
+ * Once set it can only be cleared by core or hard/soft reset.
+ */
+#define CC_ADMIN_CONFIG_CHANGE_BIT	BIT(30)
+#define CC_ADMIN_GATE_ENABLE_BIT	BIT(31)
+
+#define GATE_STATE			0x8
+#define GS_OPER_GATE_STATE_SHIFT	(0)
+#define GS_OPER_GATE_STATE_MASK		(0x7)
+#define GS_OPER_CTRL_LIST_LENGTH_SHIFT	(8)
+#define GS_OPER_CTRL_LIST_LENGTH_MASK	(0x3F)
+#define GS_SUP_MAX_LIST_LENGTH_SHIFT	(16)
+#define GS_SUP_MAX_LIST_LENGTH_MASK	(0x3F)
+#define GS_TICK_GRANULARITY_SHIFT	(24)
+#define GS_TICK_GRANULARITY_MASK	(0x3F)
+
+#define ADMIN_CYCLE_TIME_DENOMINATOR	0x18
+#define ADMIN_BASE_TIME_NS		0x20
+#define ADMIN_BASE_TIME_SEC		0x24
+#define ADMIN_BASE_TIME_SECS		0x28
+
+#define INT_STATUS			0x30
+#define INT_ENABLE			0x34
+#define INT_CLEAR			0x38
+#define PORT_STATUS			0x3c
+
+/* Config Change time is valid after Config Pending bit is set. */
+#define CONFIG_CHANGE_TIME_NS		0x40
+#define CONFIG_CHANGE_TIME_SEC		0x44
+#define CONFIG_CHANGE_TIME_SECS		0x48
+
+#define OPER_CONTROL_LIST_LENGTH	0x50
+#define OPER_CYCLE_TIME_DENOMINATOR	0x58
+#define CYCLE_TIME_DENOMINATOR_MASK	(0x3FFFFFFF)
+
+#define OPER_BASE_TIME_NS		0x60
+#define OPER_BASE_TIME_NS_MASK		(0x3FFFFFFF)
+#define OPER_BASE_TIME_SEC		0x64
+#define OPER_BASE_TIME_SECS		0x68
+#define BASE_TIME_SECS_MASK		(0xFFFF)
+
+#define BE_XMIT_OVERRUN_COUNT		0x6c
+#define RES_XMIT_OVERRUN_COUNT		0x74
+#define ST_XMIT_OVERRUN_COUNT		0x7c
+
+/* internally hw deals with queues only,
+ * in 3q system ST acl bitmap would be would 1 << 2
+ * in 2q system ST acl bitmap would be 1 << 1
+ * But this is confusing to users.
+ * so use the following fixed gate state and internally
+ * map them to hw
+ */
+#define GS_BE_OPEN			BIT(0)
+#define GS_RE_OPEN			BIT(1)
+#define GS_ST_OPEN			BIT(2)
+#define QBV_MAX_ENTRIES			256
+
+struct qbv_info {
+	u8 port;
+	u8 force;
+	u32 cycle_time;
+	u64 ptp_time_sec;
+	u32 ptp_time_ns;
+	u32 list_length;
+	u32 acl_gate_state[QBV_MAX_ENTRIES];
+	u32 acl_gate_time[QBV_MAX_ENTRIES];
+};
+
+#endif /* XILINX_TSN_SHAPER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_switch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_switch.c
@@ -0,0 +1,1865 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx FPGA Xilinx TSN Switch Controller driver.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/of_platform.h>
+#include <linux/module.h>
+#include <linux/miscdevice.h>
+#include <linux/of_net.h>
+#include "xilinx_tsn_switch.h"
+
+static struct miscdevice switch_dev;
+static struct device_node *ep_node;
+struct axienet_local lp;
+static struct axienet_local *ep_lp;
+static u8 en_hw_addr_learning;
+static u8 sw_mac_addr[ETH_ALEN];
+
+#define DELAY_OF_FIVE_MILLISEC			(5 * DELAY_OF_ONE_MILLISEC)
+
+#define ADD					1
+#define DELETE					0
+
+#define PMAP_EGRESS_QUEUE_MASK			0x7
+#define PMAP_EGRESS_QUEUE0_SELECT		0x0
+#define PMAP_EGRESS_QUEUE1_SELECT		0x1
+#define PMAP_EGRESS_QUEUE2_SELECT		0x2
+#define SDL_EN_CAM_IPV_SHIFT			28
+#define SDL_CAM_IPV_SHIFT			29
+
+#define SDL_CAM_WR_ENABLE			BIT(0)
+#define SDL_CAM_ADD_ENTRY			0x3
+#define SDL_CAM_DELETE_ENTRY			0x5
+#define SDL_CAM_READ_KEY_ENTRY			0x1
+#define SDL_CAM_READ_ENTRY			GENMASK(2, 0)
+#define SDL_CAM_VLAN_SHIFT			16
+#define SDL_CAM_VLAN_MASK			0xFFF
+#define SDL_CAM_IPV_MASK			0x7
+#define SDL_CAM_PORT_LIST_SHIFT			8
+#define SDL_GATEID_SHIFT			16
+#define SDL_CAM_EP_MGMTQ_EN			BIT(15)
+#define SDL_CAM_FWD_TO_EP			BIT(0)
+#define SDL_CAM_FWD_TO_PORT_1			BIT(1)
+#define SDL_CAM_FWD_TO_PORT_2			BIT(2)
+#define SDL_CAM_EP_ACTION_LIST_SHIFT		0
+#define SDL_CAM_MAC_ACTION_LIST_SHIFT		4
+#define SDL_CAM_DEST_MAC_XLATION		BIT(0)
+#define SDL_CAM_VLAN_ID_XLATION			BIT(1)
+#define SDL_CAM_UNTAG_FRAME			BIT(2)
+#define SDL_CAM_TAG_FRAME			BIT(3)
+
+#define PORT_MAC_ADDR_LSB_MASK			(0xF)
+#define MAC2_PORT_MAC_ADDR_LSB_SHIFT		(20)
+#define PORT_STATUS_MASK                       (0x7)
+#define MAC2_PORT_STATUS_SHIFT                 (17)
+#define MAC2_PORT_STATUS_CHG_BIT               BIT(16)
+#define MAC1_PORT_MAC_ADDR_LSB_SHIFT		(12)
+#define MAC1_PORT_STATUS_SHIFT                 (9)
+#define MAC1_PORT_STATUS_CHG_BIT               BIT(8)
+#define EP_PORT_STATUS_SHIFT                   (1)
+#define EP_PORT_STATUS_CHG_BIT                 BIT(0)
+#define EX_EP_PORT_STATUS_SHIFT			(25)
+#define EX_EP_PORT_STATUS_CHG_BIT		BIT(24)
+
+#define SDL_CAM_LEARNT_ENT_MAC2_SHIFT		(20)
+#define SDL_CAM_LEARNT_ENT_MAC1_SHIFT		(8)
+#define SDL_CAM_LEARNT_ENT_MASK			GENMASK(11, 0)
+#define SDL_CAM_FOUND_BIT			BIT(7)
+#define SDL_CAM_READ_KEY_ADDR_SHIFT		(8)
+
+#define HW_ADDR_AGING_TIME_SHIFT		(8)
+#define HW_ADDR_AGING_TIME_MASK			GENMASK(19, 0)
+#define HW_ADDR_AGING_BIT			BIT(2)
+#define HW_ADDR_LEARN_UNTAG_BIT			BIT(1)
+#define HW_ADDR_LEARN_BIT			BIT(0)
+
+#define PORT_VLAN_ID_SHIFT			(16)
+#define PORT_VLAN_ID_MASK			(0xFFF)
+#define PORT_VLAN_IPV_SHIFT			(13)
+#define PORT_VLAN_EN_IPV_SHIFT			(12)
+#define PORT_VLAN_WRITE				(0x3)
+#define PORT_VLAN_READ				(0x1)
+#define PORT_VLAN_WRITE_READ_EN_BIT		BIT(0)
+#define PORT_VLAN_PORT_LIST_VALID_BIT		BIT(3)
+#define PORT_VLAN_HW_ADDR_LEARN_BIT		BIT(9)
+#define PORT_VLAN_HW_ADDR_AGING_BIT		BIT(11)
+#define PORT_VLAN_HW_ADDR_AGING_TIME_SHIFT	(12)
+
+#define NATIVE_MAC1_PCP_SHIFT			(13)
+#define NATIVE_MAC2_VLAN_SHIFT			(16)
+#define NATIVE_MAC2_PCP_SHIFT			(29)
+
+#define DEFAULT_PVID		1
+#define DEFAULT_FWD_ALL		GENMASK(2, 0)
+
+/* Match table for of_platform binding */
+static const struct of_device_id tsnswitch_of_match[] = {
+	{ .compatible = "xlnx,tsn-switch", },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, tsnswitch_of_match);
+
+static int switch_open(struct inode *inode, struct file *file)
+{
+	return 0;
+}
+
+static int switch_release(struct inode *inode, struct file *file)
+{
+	return 0;
+}
+
+/* set_frame_filter_option Frame Filtering Type Field Options */
+static void set_frame_filter_opt(u16 type1, u16 type2)
+{
+	int type = axienet_ior(&lp, XAS_FRM_FLTR_TYPE_FIELD_OPT_OFFSET);
+
+	if (type1)
+		type = (type & 0x0000FFFF) | (type1 << 16);
+	if (type2)
+		type = (type & 0xFFFF0000) | type2;
+	axienet_iow(&lp, XAS_FRM_FLTR_TYPE_FIELD_OPT_OFFSET, type);
+}
+
+/* MAC Port-1 Management Queueing Options */
+static void set_mac1_mngmntq(u32 config)
+{
+	axienet_iow(&lp, XAS_MAC1_MNG_Q_OPTION_OFFSET, config);
+}
+
+/* MAC Port-2 Management Queueing Options */
+static void set_mac2_mngmntq(u32 config)
+{
+	axienet_iow(&lp, XAS_MNG_Q_CTRL_OFFSET, config);
+}
+
+static int set_pmap_config(struct pmap_data pri_info)
+{
+	u32 pmap = 0;
+	u8 pmap_priority_shift = 0;
+	u8 i = 0;
+	u32 reg, err;
+	u16 num_q = lp.num_tc;
+
+	/* wait for switch init done */
+	err = readl_poll_timeout(lp.regs + XAS_STATUS_OFFSET, reg,
+				 (reg & SDL_CAM_WR_ENABLE), 10,
+				  DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM init timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	if (num_q == 3) {
+		/* map pcp's to queues in accordance with device tree */
+		i = 0;
+		while (i < 8) {
+			if (pri_info.st_pcp_reg & (1 << i)) {
+				pmap_priority_shift = 4 * i;
+				pmap = pmap |
+				PMAP_EGRESS_QUEUE2_SELECT << pmap_priority_shift;
+			} else if (pri_info.res_pcp_reg & (1 << i)) {
+				pmap_priority_shift = 4 * i;
+				pmap = pmap |
+				PMAP_EGRESS_QUEUE1_SELECT << pmap_priority_shift;
+			}
+			i = i + 1;
+		}
+	} else {
+		i = 0;
+		while (i < 8) {
+			if (pri_info.st_pcp_reg & (1 << i)) {
+				pmap_priority_shift = 4 * i;
+				pmap = pmap |
+				PMAP_EGRESS_QUEUE1_SELECT << pmap_priority_shift;
+			}
+			i = i + 1;
+		}
+	}
+
+	axienet_iow(&lp, XAS_PMAP_OFFSET, pmap);
+
+	/* wait for cam init done */
+	err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_STATUS_OFFSET, reg,
+				 (reg & SDL_CAM_WR_ENABLE), 10,
+				  DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM init timed out\n");
+		return -ETIMEDOUT;
+	}
+	return 0;
+}
+
+/**
+ * set_switch_regs -  read the various status of switch
+ * @data:	Pointer which will be writen to switch
+ */
+static void set_switch_regs(struct switch_data *data)
+{
+	int tmp;
+	u8 mac_addr[6];
+
+	axienet_iow(&lp, XAS_CONTROL_OFFSET, data->switch_ctrl);
+	axienet_iow(&lp, XAS_PMAP_OFFSET, data->switch_prt);
+	mac_addr[0] = data->sw_mac_addr[0];
+	mac_addr[1] = data->sw_mac_addr[1];
+	mac_addr[2] = data->sw_mac_addr[2];
+	mac_addr[3] = data->sw_mac_addr[3];
+	mac_addr[4] = data->sw_mac_addr[4];
+	mac_addr[5] = data->sw_mac_addr[5];
+	axienet_iow(&lp, XAS_MAC_LSB_OFFSET,
+		    (mac_addr[0] << 24) | (mac_addr[1] << 16) |
+		    (mac_addr[2] << 8)  | (mac_addr[3]));
+	axienet_iow(&lp, XAS_MAC_MSB_OFFSET, (mac_addr[4] << 8) | mac_addr[5]);
+
+	/* Threshold */
+	tmp = (data->thld_ep_mac[0].t1 << 16) | data->thld_ep_mac[0].t2;
+	axienet_iow(&lp, XAS_EP2MAC_ST_FIFOT_OFFSET, tmp);
+
+	tmp = (data->thld_ep_mac[1].t1 << 16) | data->thld_ep_mac[1].t2;
+	axienet_iow(&lp, XAS_EP2MAC_RE_FIFOT_OFFSET, tmp);
+
+	tmp = (data->thld_ep_mac[2].t1 << 16) | data->thld_ep_mac[2].t2;
+	axienet_iow(&lp, XAS_EP2MAC_BE_FIFOT_OFFSET, tmp);
+
+	tmp = (data->thld_mac_mac[0].t1 << 16) | data->thld_mac_mac[0].t2;
+	axienet_iow(&lp, XAS_MAC2MAC_ST_FIFOT_OFFSET, tmp);
+
+	tmp = (data->thld_mac_mac[1].t1 << 16) | data->thld_mac_mac[1].t2;
+	axienet_iow(&lp, XAS_MAC2MAC_RE_FIFOT_OFFSET, tmp);
+
+	tmp = (data->thld_mac_mac[2].t1 << 16) | data->thld_mac_mac[2].t2;
+	axienet_iow(&lp, XAS_MAC2MAC_BE_FIFOT_OFFSET, tmp);
+
+	/* Port VLAN ID */
+	axienet_iow(&lp, XAS_EP_PORT_VLAN_OFFSET, data->ep_vlan);
+	axienet_iow(&lp, XAS_MAC_PORT_VLAN_OFFSET, data->mac_vlan);
+
+	/* max frame size */
+	axienet_iow(&lp, XAS_ST_MAX_FRAME_SIZE_OFFSET, data->max_frame_sc_que);
+	axienet_iow(&lp, XAS_RE_MAX_FRAME_SIZE_OFFSET, data->max_frame_res_que);
+	axienet_iow(&lp, XAS_BE_MAX_FRAME_SIZE_OFFSET, data->max_frame_be_que);
+}
+
+/**
+ * get_switch_regs -  read the various status of switch
+ * @data:	Pointer which will return the switch status
+ */
+static void get_switch_regs(struct switch_data *data)
+{
+	int tmp;
+
+	data->switch_status = axienet_ior(&lp, XAS_STATUS_OFFSET);
+	data->switch_ctrl = axienet_ior(&lp, XAS_CONTROL_OFFSET);
+	data->switch_prt = axienet_ior(&lp, XAS_PMAP_OFFSET);
+	tmp = axienet_ior(&lp, XAS_MAC_LSB_OFFSET);
+	data->sw_mac_addr[0] = (tmp & 0xFF000000) >> 24;
+	data->sw_mac_addr[1] = (tmp & 0xFF0000) >> 16;
+	data->sw_mac_addr[2] = (tmp & 0xFF00) >> 8;
+	data->sw_mac_addr[3] = (tmp & 0xFF);
+	tmp = axienet_ior(&lp, XAS_MAC_MSB_OFFSET);
+	data->sw_mac_addr[4] = (tmp & 0xFF00) >> 8;
+	data->sw_mac_addr[5] = (tmp & 0xFF);
+
+	/* Threshold */
+	tmp = axienet_ior(&lp, XAS_EP2MAC_ST_FIFOT_OFFSET);
+	data->thld_ep_mac[0].t1 = ((tmp >> 16) & 0xFFFF);
+	data->thld_ep_mac[0].t2 = tmp & (0xFFFF);
+
+	tmp = axienet_ior(&lp, XAS_EP2MAC_RE_FIFOT_OFFSET);
+	data->thld_ep_mac[1].t1 = ((tmp >> 16) & 0xFFFF);
+	data->thld_ep_mac[1].t2 = tmp & (0xFFFF);
+
+	tmp = axienet_ior(&lp, XAS_EP2MAC_BE_FIFOT_OFFSET);
+	data->thld_ep_mac[2].t1 = ((tmp >> 16) & 0xFFFF);
+	data->thld_ep_mac[2].t2 = tmp & (0xFFFF);
+
+	tmp = axienet_ior(&lp, XAS_MAC2MAC_ST_FIFOT_OFFSET);
+	data->thld_mac_mac[0].t1 = ((tmp >> 16) & 0xFFFF);
+	data->thld_mac_mac[0].t2 = tmp & (0xFFFF);
+
+	tmp = axienet_ior(&lp, XAS_MAC2MAC_RE_FIFOT_OFFSET);
+	data->thld_mac_mac[1].t1 = ((tmp >> 16) & 0xFFFF);
+	data->thld_mac_mac[1].t2 = tmp & (0xFFFF);
+
+	tmp = axienet_ior(&lp, XAS_MAC2MAC_BE_FIFOT_OFFSET);
+	data->thld_mac_mac[2].t1 = ((tmp >> 16) & 0xFFFF);
+	data->thld_mac_mac[2].t2 = tmp & (0xFFFF);
+
+	/* Port VLAN ID */
+	data->ep_vlan = axienet_ior(&lp, XAS_EP_PORT_VLAN_OFFSET);
+	data->mac_vlan = axienet_ior(&lp, XAS_MAC_PORT_VLAN_OFFSET);
+
+	/* max frame size */
+	data->max_frame_sc_que = (axienet_ior(&lp,
+				XAS_ST_MAX_FRAME_SIZE_OFFSET) & 0xFFFF);
+	data->max_frame_res_que = (axienet_ior(&lp,
+				XAS_RE_MAX_FRAME_SIZE_OFFSET) & 0xFFFF);
+	data->max_frame_be_que = (axienet_ior(&lp,
+				XAS_BE_MAX_FRAME_SIZE_OFFSET) & 0xFFFF);
+
+	/* frame filter type options*/
+	tmp = axienet_ior(&lp, XAS_FRM_FLTR_TYPE_FIELD_OPT_OFFSET);
+	data->typefield.type2 = (tmp & 0xFFFF0000) >> 16;
+	data->typefield.type2 = tmp & 0x0000FFFF;
+
+	/* MAC Port 1 Management Q option*/
+	data->mac1_config = axienet_ior(&lp, XAS_MAC1_MNG_Q_OPTION_OFFSET);
+	/* MAC Port 2 Management Q option*/
+	data->mac2_config = axienet_ior(&lp, XAS_MNG_Q_CTRL_OFFSET);
+
+	/* Port VLAN Membership control*/
+	data->port_vlan_mem_ctrl = axienet_ior(&lp, XAS_VLAN_MEMB_CTRL_REG);
+	/* Port VLAN Membership read data*/
+	data->port_vlan_mem_data = axienet_ior(&lp, XAS_VLAN_MEMB_DATA_REG);
+}
+
+int tsn_switch_get_port_parent_id(struct net_device *dev, struct netdev_phys_item_id *ppid)
+{
+	u8 *switchid;
+
+	switchid = tsn_switch_get_id();
+	ppid->id_len = ETH_ALEN;
+	memcpy(&ppid->id, switchid, ppid->id_len);
+
+	return 0;
+}
+
+/**
+ * get_memory_static_counter -  get memory static counters value
+ * @data:	Value to be programmed
+ */
+static void get_memory_static_counter(struct switch_data *data)
+{
+	data->mem_arr_cnt.cam_lookup.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_CAM_LOOKUP);
+	data->mem_arr_cnt.cam_lookup.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_CAM_LOOKUP + 0x4);
+
+	data->mem_arr_cnt.multicast_fr.lsb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_MULTCAST);
+	data->mem_arr_cnt.multicast_fr.msb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_MULTCAST + 0x4);
+
+	data->mem_arr_cnt.err_mac1.lsb = axienet_ior(&lp,
+						     XAS_MEM_STCNTR_ERR_MAC1);
+	data->mem_arr_cnt.err_mac1.msb = axienet_ior(&lp,
+						     XAS_MEM_STCNTR_ERR_MAC1 + 0x4);
+
+	data->mem_arr_cnt.err_mac2.lsb = axienet_ior(&lp,
+						     XAS_MEM_STCNTR_ERR_MAC2);
+	data->mem_arr_cnt.err_mac2.msb = axienet_ior(&lp,
+						     XAS_MEM_STCNTR_ERR_MAC2 + 0x4);
+
+	data->mem_arr_cnt.sc_mac1_ep.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_MAC1_EP);
+	data->mem_arr_cnt.sc_mac1_ep.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_MAC1_EP + 0x4);
+	data->mem_arr_cnt.res_mac1_ep.lsb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_MAC1_EP);
+	data->mem_arr_cnt.res_mac1_ep.msb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_MAC1_EP + 0x4);
+	data->mem_arr_cnt.be_mac1_ep.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_MAC1_EP);
+	data->mem_arr_cnt.be_mac1_ep.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_MAC1_EP + 0x4);
+	data->mem_arr_cnt.err_sc_mac1_ep.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_MAC1_EP);
+	data->mem_arr_cnt.err_sc_mac1_ep.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_MAC1_EP + 0x4);
+	data->mem_arr_cnt.err_res_mac1_ep.lsb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_MAC1_EP);
+	data->mem_arr_cnt.err_res_mac1_ep.msb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_MAC1_EP + 0x4);
+	data->mem_arr_cnt.err_be_mac1_ep.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_MAC1_EP);
+	data->mem_arr_cnt.err_be_mac1_ep.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_MAC1_EP + 0x4);
+
+	data->mem_arr_cnt.sc_mac2_ep.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_MAC2_EP);
+	data->mem_arr_cnt.sc_mac2_ep.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_MAC2_EP + 0x4);
+	data->mem_arr_cnt.res_mac2_ep.lsb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_MAC2_EP);
+	data->mem_arr_cnt.res_mac2_ep.msb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_MAC2_EP + 0x4);
+	data->mem_arr_cnt.be_mac2_ep.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_MAC2_EP);
+	data->mem_arr_cnt.be_mac2_ep.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_MAC2_EP + 0x4);
+	data->mem_arr_cnt.err_sc_mac2_ep.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_MAC2_EP);
+	data->mem_arr_cnt.err_sc_mac2_ep.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_MAC2_EP + 0x4);
+	data->mem_arr_cnt.err_res_mac2_ep.lsb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_MAC2_EP);
+	data->mem_arr_cnt.err_res_mac2_ep.msb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_MAC2_EP + 0x4);
+	data->mem_arr_cnt.err_be_mac2_ep.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_MAC2_EP);
+	data->mem_arr_cnt.err_be_mac2_ep.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_MAC2_EP + 0x4);
+
+	data->mem_arr_cnt.sc_ep_mac1.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_EP_MAC1);
+	data->mem_arr_cnt.sc_ep_mac1.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_EP_MAC1 + 0x4);
+	data->mem_arr_cnt.res_ep_mac1.lsb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_EP_MAC1);
+	data->mem_arr_cnt.res_ep_mac1.msb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_EP_MAC1 + 0x4);
+	data->mem_arr_cnt.be_ep_mac1.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_EP_MAC1);
+	data->mem_arr_cnt.be_ep_mac1.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_EP_MAC1 + 0x4);
+	data->mem_arr_cnt.err_sc_ep_mac1.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_EP_MAC1);
+	data->mem_arr_cnt.err_sc_ep_mac1.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_EP_MAC1 + 0x4);
+	data->mem_arr_cnt.err_res_ep_mac1.lsb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_EP_MAC1);
+	data->mem_arr_cnt.err_res_ep_mac1.msb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_EP_MAC1 + 0x4);
+	data->mem_arr_cnt.err_be_ep_mac1.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_EP_MAC1);
+	data->mem_arr_cnt.err_be_ep_mac1.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_EP_MAC1 + 0x4);
+
+	data->mem_arr_cnt.sc_mac2_mac1.lsb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_SC_MAC2_MAC1);
+	data->mem_arr_cnt.sc_mac2_mac1.msb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_SC_MAC2_MAC1 + 0x4);
+	data->mem_arr_cnt.res_mac2_mac1.lsb = axienet_ior(&lp,
+							  XAS_MEM_STCNTR_RES_MAC2_MAC1);
+	data->mem_arr_cnt.res_mac2_mac1.msb = axienet_ior(&lp,
+							  XAS_MEM_STCNTR_RES_MAC2_MAC1 + 0x4);
+	data->mem_arr_cnt.be_mac2_mac1.lsb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_BE_MAC2_MAC1);
+	data->mem_arr_cnt.be_mac2_mac1.msb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_BE_MAC2_MAC1 + 0x4);
+	data->mem_arr_cnt.err_sc_mac2_mac1.lsb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_SC_MAC2_MAC1);
+	data->mem_arr_cnt.err_sc_mac2_mac1.msb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_SC_MAC2_MAC1 + 0x4);
+	data->mem_arr_cnt.err_res_mac2_mac1.lsb = axienet_ior(&lp,
+							      XAS_MEM_STCNTR_ERR_RES_MAC2_MAC1);
+	data->mem_arr_cnt.err_res_mac2_mac1.msb =
+	axienet_ior(&lp, XAS_MEM_STCNTR_ERR_RES_MAC2_MAC1 + 0x4);
+	data->mem_arr_cnt.err_be_mac2_mac1.lsb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_BE_MAC2_MAC1);
+	data->mem_arr_cnt.err_be_mac2_mac1.msb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_BE_MAC2_MAC1 + 0x4);
+
+	data->mem_arr_cnt.sc_ep_mac2.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_EP_MAC2);
+	data->mem_arr_cnt.sc_ep_mac2.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_SC_EP_MAC2 + 0x4);
+	data->mem_arr_cnt.res_ep_mac2.lsb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_EP_MAC2);
+	data->mem_arr_cnt.res_ep_mac2.msb = axienet_ior(&lp,
+							XAS_MEM_STCNTR_RES_EP_MAC2 + 0x4);
+	data->mem_arr_cnt.be_ep_mac2.lsb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_EP_MAC2);
+	data->mem_arr_cnt.be_ep_mac2.msb = axienet_ior(&lp,
+						       XAS_MEM_STCNTR_BE_EP_MAC2 + 0x4);
+	data->mem_arr_cnt.err_sc_ep_mac2.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_EP_MAC2);
+	data->mem_arr_cnt.err_sc_ep_mac2.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_SC_EP_MAC2 + 0x4);
+	data->mem_arr_cnt.err_res_ep_mac2.lsb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_EP_MAC2);
+	data->mem_arr_cnt.err_res_ep_mac2.msb = axienet_ior(&lp,
+							    XAS_MEM_STCNTR_ERR_RES_EP_MAC2 + 0x4);
+	data->mem_arr_cnt.err_be_ep_mac2.lsb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_EP_MAC2);
+	data->mem_arr_cnt.err_be_ep_mac2.msb = axienet_ior(&lp,
+							   XAS_MEM_STCNTR_ERR_BE_EP_MAC2 + 0x4);
+
+	data->mem_arr_cnt.sc_mac1_mac2.lsb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_SC_MAC1_MAC2);
+	data->mem_arr_cnt.sc_mac1_mac2.msb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_SC_MAC1_MAC2 + 0x4);
+	data->mem_arr_cnt.res_mac1_mac2.lsb = axienet_ior(&lp,
+							  XAS_MEM_STCNTR_RES_MAC1_MAC2);
+	data->mem_arr_cnt.res_mac1_mac2.msb = axienet_ior(&lp,
+							  XAS_MEM_STCNTR_RES_MAC1_MAC2 + 0x4);
+	data->mem_arr_cnt.be_mac1_mac2.lsb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_BE_MAC1_MAC2);
+	data->mem_arr_cnt.be_mac1_mac2.msb = axienet_ior(&lp,
+							 XAS_MEM_STCNTR_BE_MAC1_MAC2 + 0x4);
+	data->mem_arr_cnt.err_sc_mac1_mac2.lsb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_SC_MAC1_MAC2);
+	data->mem_arr_cnt.err_sc_mac1_mac2.msb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_SC_MAC1_MAC2 + 0x4);
+	data->mem_arr_cnt.err_res_mac1_mac2.lsb = axienet_ior(&lp,
+							      XAS_MEM_STCNTR_ERR_RES_MAC1_MAC2);
+	data->mem_arr_cnt.err_res_mac1_mac2.msb =
+	axienet_ior(&lp, XAS_MEM_STCNTR_ERR_RES_MAC1_MAC2 + 0x4);
+	data->mem_arr_cnt.err_be_mac1_mac2.lsb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_BE_MAC1_MAC2);
+	data->mem_arr_cnt.err_be_mac1_mac2.msb = axienet_ior(&lp,
+							     XAS_MEM_STCNTR_ERR_BE_MAC1_MAC2 + 0x4);
+}
+
+int tsn_switch_cam_set(struct cam_struct data, u8 add)
+{
+	u32 port_action = 0;
+	u32 tv2 = 0;
+	u32 reg, err;
+	u8 en_ipv = 0;
+
+	err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_STATUS_OFFSET, reg,
+				 (reg & SDL_CAM_WR_ENABLE), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM init timed out\n");
+		return -ETIMEDOUT;
+	}
+	if (add && ((data.fwd_port & PORT_EX_ONLY) || (data.fwd_port & PORT_EX_EP))) {
+		if (!(ep_lp->ex_ep)) {
+			pr_err("Endpoint extension support is not present in this design\n");
+			return -EINVAL;
+		} else if ((data.fwd_port & PORT_EX_ONLY) &&
+			    (data.fwd_port & PORT_EX_EP)) {
+			if (!(ep_lp->packet_switch)) {
+				pr_err("Support for forwarding packets from endpoint to extended endpoint or vice versa is not present in this design\n");
+				return -EINVAL;
+			}
+		}
+	}
+	/* mac and vlan */
+	axienet_iow(&lp, XAS_SDL_CAM_KEY1_OFFSET,
+		    (data.dest_addr[0] << 24) | (data.dest_addr[1] << 16) |
+		    (data.dest_addr[2] << 8)  | (data.dest_addr[3]));
+	axienet_iow(&lp, XAS_SDL_CAM_KEY2_OFFSET,
+		    ((data.dest_addr[4] << 8) | data.dest_addr[5]) |
+		    ((data.vlanid & SDL_CAM_VLAN_MASK) << SDL_CAM_VLAN_SHIFT));
+
+	/* Introduce wmb to preserve KEY2 and TV1 write order fix possible
+	 * HW hang when KEY2 and TV1 registers are accessed sequentially.
+	 * TODO: Check alternatives to barrier.
+	 */
+	wmb();
+	/* TV 1 and TV 2 */
+	axienet_iow(&lp, XAS_SDL_CAM_TV1_OFFSET,
+		    (data.src_addr[0] << 24) | (data.src_addr[1] << 16) |
+		    (data.src_addr[2] << 8)  | (data.src_addr[3]));
+
+	tv2 = ((data.src_addr[4] << 8) | data.src_addr[5]) |
+	       ((data.tv_vlanid & SDL_CAM_VLAN_MASK) << SDL_CAM_VLAN_SHIFT);
+
+	if (data.flags & XAS_CAM_IPV_EN)
+		en_ipv = 1;
+
+	tv2 = tv2 | ((data.ipv & SDL_CAM_IPV_MASK) << SDL_CAM_IPV_SHIFT)
+				| (en_ipv << SDL_EN_CAM_IPV_SHIFT);
+
+	axienet_iow(&lp, XAS_SDL_CAM_TV2_OFFSET, tv2);
+	/* Force complete write to translation value registers
+	 * before writing to port action register
+	 * TODO: Check alternatives to barrier.
+	 */
+	wmb();
+
+	if (data.fwd_port & PORT_EP)
+		port_action = data.ep_port_act << SDL_CAM_EP_ACTION_LIST_SHIFT;
+	if (data.fwd_port & PORT_MAC1 || data.fwd_port & PORT_MAC2)
+		port_action |= data.mac_port_act <<
+				SDL_CAM_MAC_ACTION_LIST_SHIFT;
+
+	if (data.flags & XAS_CAM_EP_MGMTQ_EN)
+		port_action |= SDL_CAM_EP_MGMTQ_EN;
+
+	port_action = port_action | (data.fwd_port << SDL_CAM_PORT_LIST_SHIFT);
+
+#if IS_ENABLED(CONFIG_XILINX_TSN_QCI) || IS_ENABLED(CONFIG_XILINX_TSN_CB)
+	port_action = port_action | (data.gate_id << SDL_GATEID_SHIFT);
+#endif
+
+	/* port action */
+	axienet_iow(&lp, XAS_SDL_CAM_PORT_ACT_OFFSET, port_action);
+	/* Force complete writes to port action register before initiating
+	 * CAM write by setting CAM ADD bit in control register since this value
+	 * needs to be written to the CAM.
+	 * TODO: Check alternatives to barrier.
+	 */
+	wmb();
+
+	if (add)
+		axienet_iow(&lp, XAS_SDL_CAM_CTRL_OFFSET, SDL_CAM_ADD_ENTRY);
+	else
+		axienet_iow(&lp, XAS_SDL_CAM_CTRL_OFFSET, SDL_CAM_DELETE_ENTRY);
+
+	/* wait for write to complete */
+	err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_CTRL_OFFSET, reg,
+				 (!(reg & SDL_CAM_WR_ENABLE)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM write timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static void port_vlan_mem_ctrl(u32 port_vlan_mem)
+{
+		axienet_iow(&lp, XAS_VLAN_MEMB_CTRL_REG, port_vlan_mem);
+}
+
+static int read_cam_entry(struct cam_struct data, void __user *arg)
+{
+	u32 u_value, reg, err;
+
+	/* wait for cam init done */
+	err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_STATUS_OFFSET, reg,
+				 (reg & SDL_CAM_WR_ENABLE), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM init timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	/* mac and vlan */
+	axienet_iow(&lp, XAS_SDL_CAM_KEY1_OFFSET,
+		    (data.dest_addr[0] << 24) | (data.dest_addr[1] << 16) |
+		    (data.dest_addr[2] << 8)  | (data.dest_addr[3]));
+	axienet_iow(&lp, XAS_SDL_CAM_KEY2_OFFSET,
+		    ((data.dest_addr[4] << 8) | data.dest_addr[5]) |
+		    ((data.vlanid & SDL_CAM_VLAN_MASK) << SDL_CAM_VLAN_SHIFT));
+	/* Finish writing vlan id and mac address before triggering a read
+	 * from the CAM since read depends on these parameters
+	 * TODO: Check alternatives to barrier.
+	 */
+	wmb();
+	axienet_iow(&lp, XAS_SDL_CAM_CTRL_OFFSET, SDL_CAM_READ_ENTRY);
+	err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_CTRL_OFFSET, reg,
+				 (!(reg & SDL_CAM_WR_ENABLE)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM write timed out\n");
+		return -ETIMEDOUT;
+	}
+	u_value = axienet_ior(&lp, XAS_SDL_CAM_CTRL_OFFSET);
+
+	if (u_value & SDL_CAM_FOUND_BIT) {
+		u_value = axienet_ior(&lp, XAS_SDL_CAM_TV1_OFFSET);
+		data.src_addr[0] = (u_value >> 24) & 0xFF;
+		data.src_addr[1] = (u_value >> 16) & 0xFF;
+		data.src_addr[2] = (u_value >> 8) & 0xFF;
+		data.src_addr[3] = (u_value) & 0xFF;
+		u_value = axienet_ior(&lp, XAS_SDL_CAM_TV2_OFFSET);
+		data.src_addr[4] = (u_value >> 8) & 0xFF;
+		data.src_addr[5] = (u_value) & 0xFF;
+		data.tv_vlanid   = (u_value >> SDL_CAM_VLAN_SHIFT)
+					& SDL_CAM_VLAN_MASK;
+		data.ipv = (u_value >> SDL_CAM_IPV_SHIFT) & SDL_CAM_IPV_MASK;
+		if ((u_value >> SDL_EN_CAM_IPV_SHIFT) & 0x1)
+			data.flags |= XAS_CAM_IPV_EN;
+		u_value = axienet_ior(&lp, XAS_SDL_CAM_PORT_ACT_OFFSET);
+		if (ep_lp->ex_ep)
+			data.fwd_port = (u_value >> SDL_CAM_PORT_LIST_SHIFT) & 0x1F;
+		else
+			data.fwd_port = (u_value >> SDL_CAM_PORT_LIST_SHIFT) & 0x7;
+		data.ep_port_act = (u_value >> SDL_CAM_EP_ACTION_LIST_SHIFT)
+					& 0xF;
+		data.mac_port_act = (u_value >> SDL_CAM_MAC_ACTION_LIST_SHIFT)
+					& 0xF;
+		data.gate_id = (u_value >> SDL_GATEID_SHIFT) & 0xFF;
+		data.flags |= XAS_CAM_VALID;
+	} else {
+		data.flags &= ~XAS_CAM_VALID;
+	}
+	if (copy_to_user(arg, &data, sizeof(struct cam_struct)))
+		return -EFAULT;
+
+	return 0;
+}
+
+static int set_mac_addr_learn(void __user *arg)
+{
+	struct mac_addr_learn mac_learn;
+	u32 u_value;
+
+	if (copy_from_user(&mac_learn, arg, sizeof(struct mac_addr_learn)))
+		return -EFAULT;
+
+	u_value = axienet_ior(&lp, XAS_HW_ADDR_LEARN_CTRL_OFFSET);
+	if (mac_learn.aging_time) {
+		u_value &= ~(HW_ADDR_AGING_TIME_MASK <<
+				HW_ADDR_AGING_TIME_SHIFT);
+		u_value |= (mac_learn.aging_time << HW_ADDR_AGING_TIME_SHIFT);
+	}
+	if (mac_learn.is_age) {
+		if (!mac_learn.aging)
+			u_value |= HW_ADDR_AGING_BIT;
+		else
+			u_value &= ~HW_ADDR_AGING_BIT;
+	}
+	if (mac_learn.is_learn) {
+		if (!mac_learn.learning)
+			u_value |= HW_ADDR_LEARN_BIT;
+		else
+			u_value &= ~HW_ADDR_LEARN_BIT;
+	}
+	if (mac_learn.is_untag) {
+		if (mac_learn.learn_untag)
+			u_value |= HW_ADDR_LEARN_UNTAG_BIT;
+		else
+			u_value &= ~HW_ADDR_LEARN_UNTAG_BIT;
+	}
+	axienet_iow(&lp, XAS_HW_ADDR_LEARN_CTRL_OFFSET, u_value);
+
+	return 0;
+}
+
+static int get_mac_addr_learn(void __user *arg)
+{
+	struct mac_addr_learn mac_learn;
+	u32 u_value;
+
+	u_value = axienet_ior(&lp, XAS_HW_ADDR_LEARN_CTRL_OFFSET);
+	mac_learn.aging_time = (u_value >> HW_ADDR_AGING_TIME_SHIFT) &
+				HW_ADDR_AGING_TIME_MASK;
+	mac_learn.aging = u_value & HW_ADDR_AGING_BIT;
+	mac_learn.learning = u_value & HW_ADDR_LEARN_BIT;
+	mac_learn.learn_untag = u_value & HW_ADDR_LEARN_UNTAG_BIT;
+
+	u_value = axienet_ior(&lp, XAS_PORT_STATE_CTRL_OFFSET);
+
+	if (copy_to_user(arg, &mac_learn, sizeof(struct mac_addr_learn)))
+		return -EFAULT;
+
+	return 0;
+}
+
+static int get_mac_addr_learnt_list(void __user *arg)
+{
+	struct mac_addr_list *mac_list;
+	u32 i = 0;
+	u32 u_value, reg, err;
+	u16 read_key_addr = 0;
+	int ret = 0;
+
+	mac_list = kzalloc(sizeof(*mac_list), GFP_KERNEL);
+	if (!mac_list) {
+		ret = -ENOMEM;
+		goto ret_status;
+	}
+
+	if (copy_from_user(mac_list, arg, sizeof(u8))) {
+		ret = -EFAULT;
+		goto free_mac_list;
+	}
+	/* wait for cam init done */
+	err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_STATUS_OFFSET, reg,
+				 (reg & SDL_CAM_WR_ENABLE), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM init timed out\n");
+		ret = -ETIMEDOUT;
+		goto free_mac_list;
+	}
+	u_value = axienet_ior(&lp, XAS_SDL_CAM_STATUS_OFFSET);
+
+	if (mac_list->port_num == PORT_MAC1) {
+		mac_list->num_list = (u_value >> SDL_CAM_LEARNT_ENT_MAC1_SHIFT)
+					& SDL_CAM_LEARNT_ENT_MASK;
+	} else {
+		mac_list->num_list = (u_value >> SDL_CAM_LEARNT_ENT_MAC2_SHIFT)
+					& SDL_CAM_LEARNT_ENT_MASK;
+		read_key_addr = 0x800;
+	}
+
+	for (i = 0; i < MAX_NUM_MAC_ENTRIES ; i++) {
+		err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_STATUS_OFFSET, reg,
+					 (reg & SDL_CAM_WR_ENABLE), 10,
+					 DELAY_OF_FIVE_MILLISEC);
+		if (err) {
+			pr_err("CAM init timed out\n");
+			ret = -ETIMEDOUT;
+			goto free_mac_list;
+		}
+
+		u_value = ((read_key_addr + i) << SDL_CAM_READ_KEY_ADDR_SHIFT)
+			  | SDL_CAM_READ_KEY_ENTRY;
+		axienet_iow(&lp, XAS_SDL_CAM_CTRL_OFFSET, u_value);
+
+		err = readl_poll_timeout(lp.regs + XAS_SDL_CAM_CTRL_OFFSET, reg,
+					 (!(reg & SDL_CAM_WR_ENABLE)), 10,
+					 DELAY_OF_FIVE_MILLISEC);
+		if (err) {
+			pr_err("CAM write timed out\n");
+			ret = -ETIMEDOUT;
+			goto free_mac_list;
+		}
+		u_value = axienet_ior(&lp, XAS_SDL_CAM_CTRL_OFFSET);
+
+		if (u_value & SDL_CAM_FOUND_BIT) {
+			u_value = axienet_ior(&lp, XAS_SDL_CAM_KEY1_OFFSET);
+			mac_list->list[i].mac_addr[0] = (u_value >> 24) & 0xFF;
+			mac_list->list[i].mac_addr[1] = (u_value >> 16) & 0xFF;
+			mac_list->list[i].mac_addr[2] = (u_value >> 8) & 0xFF;
+			mac_list->list[i].mac_addr[3] = (u_value) & 0xFF;
+			u_value = axienet_ior(&lp, XAS_SDL_CAM_KEY2_OFFSET);
+			mac_list->list[i].mac_addr[4] = (u_value >> 8) & 0xFF;
+			mac_list->list[i].mac_addr[5] = (u_value) & 0xFF;
+			mac_list->list[i].vlan_id     = (u_value >> 16) & 0xFFF;
+		}
+	}
+	if (copy_to_user(arg, mac_list, sizeof(struct mac_addr_list))) {
+		ret = -EFAULT;
+		goto free_mac_list;
+	}
+
+free_mac_list:
+	kfree(mac_list);
+ret_status:
+	return ret;
+}
+
+int tsn_switch_set_stp_state(struct port_status *port)
+{
+	u32 u_value, reg, err;
+	u32 en_port_sts_chg_bit = 1;
+
+	u_value = axienet_ior(&lp, XAS_PORT_STATE_CTRL_OFFSET);
+	switch (port->port_num) {
+	case PORT_EP:
+		if (!(u_value & EP_PORT_STATUS_CHG_BIT)) {
+			u_value &= ~(PORT_STATUS_MASK <<
+					EP_PORT_STATUS_SHIFT);
+			u_value |= (port->port_status << EP_PORT_STATUS_SHIFT);
+			en_port_sts_chg_bit = EP_PORT_STATUS_CHG_BIT;
+		}
+		break;
+	case PORT_MAC1:
+		if (!(u_value & MAC1_PORT_STATUS_CHG_BIT)) {
+			u_value &= ~(PORT_STATUS_MASK <<
+					MAC1_PORT_STATUS_SHIFT);
+			u_value |= (port->port_status <<
+					MAC1_PORT_STATUS_SHIFT);
+			en_port_sts_chg_bit = MAC1_PORT_STATUS_CHG_BIT;
+		}
+		break;
+	case PORT_MAC2:
+		if (!(u_value & MAC2_PORT_STATUS_CHG_BIT)) {
+			u_value &= ~(PORT_STATUS_MASK <<
+					MAC2_PORT_STATUS_SHIFT);
+			u_value |= (port->port_status <<
+					MAC2_PORT_STATUS_SHIFT);
+			en_port_sts_chg_bit = MAC2_PORT_STATUS_CHG_BIT;
+		}
+		break;
+	case PORT_EX_ONLY:
+		if (!(ep_lp->ex_ep))
+			return -EINVAL;
+		if (!(u_value & EX_EP_PORT_STATUS_CHG_BIT)) {
+			u_value &= ~(PORT_STATUS_MASK << EX_EP_PORT_STATUS_SHIFT);
+			u_value |= (port->port_status << EX_EP_PORT_STATUS_SHIFT);
+			en_port_sts_chg_bit = EX_EP_PORT_STATUS_CHG_BIT;
+		}
+		break;
+	}
+
+	u_value |= en_port_sts_chg_bit;
+	axienet_iow(&lp, XAS_PORT_STATE_CTRL_OFFSET, u_value);
+
+	/* wait for write to complete */
+	err = readl_poll_timeout(lp.regs + XAS_PORT_STATE_CTRL_OFFSET, reg,
+				 (!(reg & en_port_sts_chg_bit)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("CAM write timed out\n");
+		return -ETIMEDOUT;
+	}
+	u_value = axienet_ior(&lp, XAS_PORT_STATE_CTRL_OFFSET);
+
+	return 0;
+}
+
+static int set_port_status(void __user *arg)
+{
+	struct port_status port;
+
+	if (copy_from_user(&port, arg, sizeof(struct port_status)))
+		return -EFAULT;
+
+	return tsn_switch_set_stp_state(&port);
+}
+
+static int get_port_status(void __user *arg)
+{
+	struct port_status port;
+	u32 u_value;
+
+	if (copy_from_user(&port, arg, sizeof(struct port_status)))
+		return -EINVAL;
+
+	u_value = axienet_ior(&lp, XAS_PORT_STATE_CTRL_OFFSET);
+	switch (port.port_num) {
+	case PORT_EP:
+		port.port_status = (u_value >> EP_PORT_STATUS_SHIFT) &
+					PORT_STATUS_MASK;
+		break;
+	case PORT_MAC1:
+		port.port_status = (u_value >> MAC1_PORT_STATUS_SHIFT) &
+					PORT_STATUS_MASK;
+		break;
+	case PORT_MAC2:
+		port.port_status = (u_value >> MAC2_PORT_STATUS_SHIFT) &
+					PORT_STATUS_MASK;
+		break;
+	case PORT_EX_ONLY:
+		if (!(ep_lp->ex_ep))
+			return -EINVAL;
+		port.port_status = (u_value >> EX_EP_PORT_STATUS_SHIFT) & PORT_STATUS_MASK;
+		break;
+	}
+
+	if (copy_to_user(arg, &port, sizeof(struct port_status)))
+		return -EINVAL;
+
+	return 0;
+}
+
+u8 *tsn_switch_get_id(void)
+{
+	return sw_mac_addr;
+}
+
+int tsn_switch_vlan_add(struct port_vlan *port, int add)
+{
+	u32 u_value, u_value1, reg, err;
+	u8 learning = 0;
+
+	u_value1 = axienet_ior(&lp, XAS_VLAN_MEMB_DATA_REG);
+	learning = (u_value1 & PORT_VLAN_HW_ADDR_LEARN_BIT) ? 0 : 1;
+	if (learning) {
+		if (port->en_ipv == 1) {
+			pr_err("When hardware address learning is enabled for a VLAN, TSN streams cannot be mapped to a particular priority queue\n");
+			return -EPERM;
+		}
+	} else {
+		if (port->en_port_status == 1) {
+			pr_err("When hardware address learning is disabled for a VLAN, port status cannot be set per VLAN\n");
+			return -EPERM;
+		}
+	}
+	u_value = ((port->vlan_id & PORT_VLAN_ID_MASK) << PORT_VLAN_ID_SHIFT)
+			| PORT_VLAN_READ;
+	axienet_iow(&lp, XAS_VLAN_MEMB_CTRL_REG, u_value);
+
+	/* wait for port vlan write completion */
+	err = readl_poll_timeout(lp.regs + XAS_VLAN_MEMB_CTRL_REG, reg,
+				 (!(reg & PORT_VLAN_WRITE_READ_EN_BIT)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("Port vlan write timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	if (add)
+		u_value1 |= PORT_VLAN_PORT_LIST_VALID_BIT | port->port_num;
+	else
+		u_value1 &= ~(port->port_num);
+	axienet_iow(&lp, XAS_VLAN_MEMB_DATA_REG, u_value1);
+
+	u_value = ((port->vlan_id & PORT_VLAN_ID_MASK) << PORT_VLAN_ID_SHIFT)
+			| PORT_VLAN_WRITE;
+	if (port->en_port_status == 1) {
+		u_value |= ((port->port_status & SDL_CAM_IPV_MASK) << PORT_VLAN_IPV_SHIFT)
+				| (port->en_port_status << PORT_VLAN_EN_IPV_SHIFT);
+	}
+	if (port->en_ipv == 1) {
+		u_value |= ((port->ipv & SDL_CAM_IPV_MASK) << PORT_VLAN_IPV_SHIFT)
+				| (port->en_ipv << PORT_VLAN_EN_IPV_SHIFT);
+	}
+	axienet_iow(&lp, XAS_VLAN_MEMB_CTRL_REG, u_value);
+
+	/* wait for port vlan write completion */
+	err = readl_poll_timeout(lp.regs + XAS_VLAN_MEMB_CTRL_REG, reg,
+				 (!(reg & PORT_VLAN_WRITE_READ_EN_BIT)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("Port vlan write timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int add_del_port_vlan(void __user *arg, u8 add)
+{
+	struct port_vlan port;
+
+	if (copy_from_user(&port, arg, sizeof(struct port_vlan)))
+		return -EFAULT;
+
+	return tsn_switch_vlan_add(&port, add);
+}
+
+static int set_vlan_mac_addr_learn(void __user *arg)
+{
+	struct port_vlan port;
+	u32 u_value, u_value1, reg, err;
+
+	if (copy_from_user(&port, arg, sizeof(struct port_vlan)))
+		return -EFAULT;
+
+	u_value = ((port.vlan_id & PORT_VLAN_ID_MASK) << PORT_VLAN_ID_SHIFT)
+			| PORT_VLAN_READ;
+	axienet_iow(&lp, XAS_VLAN_MEMB_CTRL_REG, u_value);
+
+	/* wait for port vlan write completion */
+	err = readl_poll_timeout(lp.regs + XAS_VLAN_MEMB_CTRL_REG, reg,
+				 (!(reg & PORT_VLAN_WRITE_READ_EN_BIT)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("Port vlan write timed out\n");
+		return -ETIMEDOUT;
+	}
+	u_value = axienet_ior(&lp, XAS_VLAN_MEMB_CTRL_REG);
+
+	u_value1 = axienet_ior(&lp, XAS_VLAN_MEMB_DATA_REG);
+
+	if (port.aging_time) {
+		u_value1 &= ~(HW_ADDR_AGING_TIME_MASK <<
+				PORT_VLAN_HW_ADDR_AGING_TIME_SHIFT);
+		u_value1 |= (port.aging_time <<
+				PORT_VLAN_HW_ADDR_AGING_TIME_SHIFT);
+	}
+	if (port.is_age) {
+		if (port.aging)
+			u_value1 |= PORT_VLAN_HW_ADDR_AGING_BIT;
+		else
+			u_value1 &= ~PORT_VLAN_HW_ADDR_AGING_BIT;
+	}
+	if (port.is_learn) {
+		if (port.learning)
+			u_value1 &= ~PORT_VLAN_HW_ADDR_LEARN_BIT;
+		else
+			u_value1 |= PORT_VLAN_HW_ADDR_LEARN_BIT;
+	}
+	axienet_iow(&lp, XAS_VLAN_MEMB_DATA_REG, u_value1);
+
+	u_value |= PORT_VLAN_WRITE;
+	axienet_iow(&lp, XAS_VLAN_MEMB_CTRL_REG, u_value);
+
+	/* wait for port vlan write completion */
+	err = readl_poll_timeout(lp.regs + XAS_VLAN_MEMB_CTRL_REG, reg,
+				 (!(reg & PORT_VLAN_WRITE_READ_EN_BIT)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("Port vlan write timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int get_vlan_mac_addr_learn(void __user *arg)
+{
+	struct port_vlan port;
+	u32 u_value, u_value1, reg, err;
+
+	if (copy_from_user(&port, arg, sizeof(struct port_vlan)))
+		return -EFAULT;
+
+	u_value = ((port.vlan_id & PORT_VLAN_ID_MASK) << PORT_VLAN_ID_SHIFT)
+			| PORT_VLAN_READ;
+	axienet_iow(&lp, XAS_VLAN_MEMB_CTRL_REG, u_value);
+
+	/* wait for port vlan write completion */
+	err = readl_poll_timeout(lp.regs + XAS_VLAN_MEMB_CTRL_REG, reg,
+				 (!(reg & PORT_VLAN_WRITE_READ_EN_BIT)), 10,
+				 DELAY_OF_FIVE_MILLISEC);
+	if (err) {
+		pr_err("Port vlan write timed out\n");
+		return -ETIMEDOUT;
+	}
+	u_value1 = axienet_ior(&lp, XAS_VLAN_MEMB_CTRL_REG);
+
+	u_value = axienet_ior(&lp, XAS_VLAN_MEMB_DATA_REG);
+
+	port.aging_time = (u_value >> PORT_VLAN_HW_ADDR_AGING_TIME_SHIFT) &
+				HW_ADDR_AGING_TIME_MASK;
+	port.aging = (u_value & PORT_VLAN_HW_ADDR_AGING_BIT) ? 1 : 0;
+	port.learning = (u_value & PORT_VLAN_HW_ADDR_LEARN_BIT) ? 0 : 1;
+	port.port_num = u_value & PORT_STATUS_MASK;
+
+#if IS_ENABLED(CONFIG_XILINX_TSN_QCI)
+	if (port.learning) {
+		port.port_status = (u_value1 >> PORT_VLAN_IPV_SHIFT) & SDL_CAM_IPV_MASK;
+		port.en_port_status = (u_value1 >> PORT_VLAN_EN_IPV_SHIFT) & 0x1;
+	} else {
+		port.ipv = (u_value1 >> PORT_VLAN_IPV_SHIFT) & SDL_CAM_IPV_MASK;
+		port.en_ipv = (u_value1 >> PORT_VLAN_EN_IPV_SHIFT) & 0x1;
+	}
+#endif
+	if (copy_to_user(arg, &port, sizeof(struct port_vlan)))
+		return -EFAULT;
+
+	return 0;
+}
+
+int tsn_switch_pvid_add(struct native_vlan *port)
+{
+	u32 u_value;
+
+	switch (port->port_num) {
+	case PORT_EP:
+		u_value = axienet_ior(&lp, XAS_EP_PORT_VLAN_OFFSET);
+		u_value &= ~PORT_VLAN_ID_MASK;
+		u_value |= port->vlan_id;
+		if (port->en_ipv) {
+			u_value &= ~(SDL_CAM_IPV_MASK << NATIVE_MAC1_PCP_SHIFT);
+			u_value |= (port->ipv << NATIVE_MAC1_PCP_SHIFT);
+		}
+		axienet_iow(&lp, XAS_EP_PORT_VLAN_OFFSET, u_value);
+		break;
+	case PORT_MAC1:
+		u_value = axienet_ior(&lp, XAS_MAC_PORT_VLAN_OFFSET);
+		u_value &= ~PORT_VLAN_ID_MASK;
+		u_value |= port->vlan_id;
+		if (port->en_ipv) {
+			u_value &= ~(SDL_CAM_IPV_MASK << NATIVE_MAC1_PCP_SHIFT);
+			u_value |= (port->ipv << NATIVE_MAC1_PCP_SHIFT);
+		}
+		axienet_iow(&lp, XAS_MAC_PORT_VLAN_OFFSET, u_value);
+		break;
+	case PORT_MAC2:
+		u_value = axienet_ior(&lp, XAS_MAC_PORT_VLAN_OFFSET);
+		u_value &= ~(PORT_VLAN_ID_MASK << NATIVE_MAC2_VLAN_SHIFT);
+		u_value |= (port->vlan_id << NATIVE_MAC2_VLAN_SHIFT);
+		if (port->en_ipv) {
+			u_value &= ~(SDL_CAM_IPV_MASK << NATIVE_MAC2_PCP_SHIFT);
+			u_value |= (port->ipv << NATIVE_MAC2_PCP_SHIFT);
+		}
+		axienet_iow(&lp, XAS_MAC_PORT_VLAN_OFFSET, u_value);
+		break;
+	}
+
+	return 0;
+}
+
+static int set_native_vlan(void __user *arg)
+{
+	struct native_vlan port;
+
+	if (copy_from_user(&port, arg, sizeof(struct native_vlan)))
+		return -EFAULT;
+
+	return tsn_switch_pvid_add(&port);
+}
+
+int tsn_switch_pvid_get(struct native_vlan *port)
+{
+	u32 u_value;
+
+	switch (port->port_num) {
+	case PORT_EP:
+		u_value = axienet_ior(&lp, XAS_EP_PORT_VLAN_OFFSET);
+		port->vlan_id = u_value & PORT_VLAN_ID_MASK;
+		port->ipv = (u_value >> NATIVE_MAC1_PCP_SHIFT) &
+				SDL_CAM_IPV_MASK;
+		break;
+	case PORT_MAC1:
+		u_value = axienet_ior(&lp, XAS_MAC_PORT_VLAN_OFFSET);
+		port->vlan_id = u_value & PORT_VLAN_ID_MASK;
+		port->ipv = (u_value >> NATIVE_MAC1_PCP_SHIFT) &
+				SDL_CAM_IPV_MASK;
+		break;
+	case PORT_MAC2:
+		u_value = axienet_ior(&lp, XAS_MAC_PORT_VLAN_OFFSET);
+		port->vlan_id = (u_value >> NATIVE_MAC2_VLAN_SHIFT) &
+				PORT_VLAN_ID_MASK;
+		port->ipv = (u_value >> NATIVE_MAC2_PCP_SHIFT) &
+				SDL_CAM_IPV_MASK;
+		break;
+	}
+
+	return 0;
+}
+
+static int get_native_vlan(void __user *arg)
+{
+	struct native_vlan port;
+
+	if (copy_from_user(&port, arg, sizeof(struct native_vlan)))
+		return -EFAULT;
+
+	tsn_switch_pvid_get(&port);
+	if (copy_to_user(arg, &port, sizeof(struct native_vlan)))
+		return -EFAULT;
+
+	return 0;
+}
+
+static long switch_ioctl(struct file *file, unsigned int cmd,
+			 unsigned long arg)
+{
+	long retval = 0;
+	struct switch_data data;
+	struct pmap_data pri_info;
+#if IS_ENABLED(CONFIG_XILINX_TSN_QCI)
+	struct qci qci_data;
+#endif
+#if IS_ENABLED(CONFIG_XILINX_TSN_CB)
+	struct cb cb_data;
+#endif
+	switch (cmd) {
+	case GET_STATUS_SWITCH:
+		/* Switch configurations */
+		get_switch_regs(&data);
+
+		/* Memory static counter*/
+		get_memory_static_counter(&data);
+		if (copy_to_user((char __user *)arg, &data, sizeof(data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+			}
+		break;
+
+	case SET_STATUS_SWITCH:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		set_switch_regs(&data);
+		break;
+
+	case ADD_CAM_ENTRY:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		if (tsn_switch_cam_set(data.cam_data, ADD)) {
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+
+	case DELETE_CAM_ENTRY:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		if (tsn_switch_cam_set(data.cam_data, DELETE)) {
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+
+	case PORT_VLAN_MEM_CTRL:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		port_vlan_mem_ctrl(data.port_vlan_mem_ctrl);
+		break;
+
+	case READ_CAM_ENTRY:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			retval = -EFAULT;
+			goto end;
+		}
+		retval = read_cam_entry(data.cam_data, (void __user *)arg);
+		break;
+
+	case SET_MAC_ADDR_LEARN_CONFIG:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = set_mac_addr_learn((void __user *)arg);
+		goto end;
+
+	case GET_MAC_ADDR_LEARN_CONFIG:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = get_mac_addr_learn((void __user *)arg);
+		goto end;
+
+	case GET_MAC_ADDR_LEARNT_LIST:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = get_mac_addr_learnt_list((void __user *)arg);
+		goto end;
+
+	case SET_PORT_STATUS:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = set_port_status((void __user *)arg);
+		goto end;
+
+	case GET_PORT_STATUS:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = get_port_status((void __user *)arg);
+		goto end;
+
+	case ADD_PORT_VLAN:
+		retval = add_del_port_vlan((void __user *)arg, ADD);
+		break;
+
+	case DEL_PORT_VLAN:
+		retval = add_del_port_vlan((void __user *)arg, DELETE);
+		break;
+
+	case SET_VLAN_MAC_ADDR_LEARN_CONFIG:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = set_vlan_mac_addr_learn((void __user *)arg);
+		break;
+
+	case GET_VLAN_MAC_ADDR_LEARN_CONFIG:
+		if (!en_hw_addr_learning)
+			return -EPERM;
+		retval = get_vlan_mac_addr_learn((void __user *)arg);
+		break;
+
+	case GET_VLAN_MAC_ADDR_LEARN_CONFIG_VLANM:
+		retval = get_vlan_mac_addr_learn((void __user *)arg);
+		break;
+
+	case SET_PORT_NATIVE_VLAN:
+		retval = set_native_vlan((void __user *)arg);
+		break;
+
+	case GET_PORT_NATIVE_VLAN:
+		retval = get_native_vlan((void __user *)arg);
+		break;
+
+	case SET_PMAP_CONFIG:
+		if (copy_from_user(&pri_info, (char __user *)arg, sizeof(pri_info))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		retval = set_pmap_config(pri_info);
+		break;
+
+	case SET_FRAME_TYPE_FIELD:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		set_frame_filter_opt(data.typefield.type1,
+				     data.typefield.type2);
+		break;
+
+	case SET_MAC1_MNGMNT_Q_CONFIG:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		set_mac1_mngmntq(data.mac1_config);
+		break;
+
+	case SET_MAC2_MNGMNT_Q_CONFIG:
+		if (copy_from_user(&data, (char __user *)arg, sizeof(data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		set_mac2_mngmntq(data.mac2_config);
+		break;
+#if IS_ENABLED(CONFIG_XILINX_TSN_QCI)
+	case CONFIG_METER_MEM:
+		if (copy_from_user(&qci_data, (char __user *)arg,
+				   sizeof(qci_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		program_meter_reg(qci_data.meter_config_data);
+		break;
+
+	case CONFIG_GATE_MEM:
+		if (copy_from_user(&qci_data, (char __user *)arg,
+				   sizeof(qci_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		config_stream_filter(qci_data.stream_config_data);
+		break;
+
+	case PSFP_CONTROL:
+		if (copy_from_user(&qci_data, (char __user *)arg,
+				   sizeof(qci_data))) {
+			retval = -EINVAL;
+			pr_err("Copy from user failed\n");
+			goto end;
+		}
+		psfp_control(qci_data.psfp_config_data);
+		break;
+
+	case GET_STATIC_PSFP_COUNTER:
+		if (copy_from_user(&qci_data, (char __user *)arg,
+				   sizeof(qci_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		get_psfp_static_counter(&qci_data.psfp_counter_data);
+		if (copy_to_user((char __user *)arg, &qci_data,
+				 sizeof(qci_data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+	case GET_METER_REG:
+		get_meter_reg(&qci_data.meter_config_data);
+		if (copy_to_user((char __user *)arg, &qci_data,
+				 sizeof(qci_data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+	case GET_STREAM_FLTR_CONFIG:
+		get_stream_filter_config(&qci_data.stream_config_data);
+		if (copy_to_user((char __user *)arg, &qci_data,
+				 sizeof(qci_data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+#endif
+#if IS_ENABLED(CONFIG_XILINX_TSN_CB)
+	case CONFIG_MEMBER_MEM:
+		if (copy_from_user(&cb_data, (char __user *)arg,
+				   sizeof(cb_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		program_member_reg(cb_data);
+		break;
+
+	case CONFIG_INGRESS_FLTR:
+		if (copy_from_user(&cb_data, (char __user *)arg,
+				   sizeof(cb_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		config_ingress_filter(cb_data);
+		break;
+
+	case FRER_CONTROL:
+		if (copy_from_user(&cb_data, (char __user *)arg,
+				   sizeof(cb_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		frer_control(cb_data.frer_ctrl_data);
+		break;
+
+	case GET_STATIC_FRER_COUNTER:
+		if (copy_from_user(&cb_data, (char __user *)arg,
+				   sizeof(cb_data))) {
+			pr_err("Copy from user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		get_frer_static_counter(&cb_data.frer_counter_data);
+		if (copy_to_user((char __user *)arg, &cb_data,
+				 sizeof(cb_data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+
+	case GET_MEMBER_REG:
+		get_member_reg(&cb_data.frer_memb_config_data);
+		if (copy_to_user((char __user *)arg, &cb_data,
+				 sizeof(cb_data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+
+	case GET_INGRESS_FLTR:
+		get_ingress_filter_config(&cb_data.in_fltr_data);
+		if (copy_to_user((char __user *)arg, &cb_data,
+				 sizeof(cb_data))) {
+			pr_err("Copy to user failed\n");
+			retval = -EINVAL;
+			goto end;
+		}
+		break;
+#endif
+	}
+end:
+	return retval;
+}
+
+static const struct file_operations switch_fops = {
+	.owner		=	THIS_MODULE,
+	.unlocked_ioctl	=	switch_ioctl,
+	.open		=	switch_open,
+	.release	=       switch_release,
+};
+
+static int tsn_switch_init(void)
+{
+	int ret;
+
+	switch_dev.minor = MISC_DYNAMIC_MINOR;
+	switch_dev.name = "switch";
+	switch_dev.fops = &switch_fops;
+	ret = misc_register(&switch_dev);
+	if (ret < 0) {
+		pr_err("Switch driver registration failed!\n");
+		return ret;
+	}
+
+	eth_random_addr((u8 *)&sw_mac_addr);
+
+	pr_debug("Xilinx TSN Switch driver initialized!\n");
+	return 0;
+}
+
+static inline void tsn_switch_set_src_mac_filter(const u8 *mac, int port)
+{
+	u32 val;
+	u32 shift = (port == 1) ? MAC1_PORT_MAC_ADDR_LSB_SHIFT :
+		MAC2_PORT_MAC_ADDR_LSB_SHIFT;
+
+	/* program the Source MAC address to filter */
+	val = axienet_ior(&lp, XAS_PORT_STATE_CTRL_OFFSET);
+
+	val &= ~(PORT_MAC_ADDR_LSB_MASK << shift);
+	val |= ((mac[5] & PORT_MAC_ADDR_LSB_MASK) << shift);
+
+	axienet_iow(&lp, XAS_PORT_STATE_CTRL_OFFSET, val);
+}
+
+/* initialize pre-configured fdbs in the system */
+static int tsn_switch_fdb_init(struct platform_device *pdev)
+{
+	u32 val, port;
+	u8 mac_addr[ETH_ALEN];
+	struct device_node *np;
+	u16 num_ports;
+	int ret;
+	struct cam_struct cam;
+
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-ports",
+				   &num_ports);
+	if (ret) {
+		dev_err(&pdev->dev, "could not read xlnx,num-ports\n");
+		return -EINVAL;
+	}
+
+	/* enable source mac based filtering */
+	val = axienet_ior(&lp, XAS_MNG_Q_CTRL_OFFSET);
+
+	/* compares Source MAC address to determine the Network
+	 * Port on which a frame needs to be forwarded for frames received
+	 * with Internal Endpoint interface.
+	 * [i.e. CPU generated  management frames]
+	 */
+	val |= (1 << XAS_MNG_Q_SRC_MAC_FIL_EN_SHIFT);
+
+	axienet_iow(&lp, XAS_MNG_Q_CTRL_OFFSET, val);
+
+	/* port0 == ep, port1 == temac1 port2 == temac2
+	 * temac1, temac2.. temacn are network ports
+	 */
+	/* network port mac addresses must differ in last lsb nibble
+	 * this is a pre-requisite;
+	 * we program the last nibble here per mac basis
+	 */
+	ep_node = of_parse_phandle(pdev->dev.of_node, "ports", 0);
+	for (port = 1; port < num_ports; port++) {
+		np = of_parse_phandle(pdev->dev.of_node, "ports", port);
+
+		ret = of_get_mac_address(np, mac_addr);
+		if (ret) {
+			dev_err(&pdev->dev, "could not find MAC address\n");
+			return -EINVAL;
+		}
+		tsn_switch_set_src_mac_filter(mac_addr, port);
+	}
+
+	/* rest of the mac addr for all ports would be same
+	 * so use the last mac instance of the loop above
+	 * set the 32bit lsb of mac address
+	 */
+	axienet_iow(&lp, XAS_MAC_LSB_OFFSET,
+		    (mac_addr[2] << 24) | (mac_addr[3] << 16) |
+		    (mac_addr[4] << 8)  | (mac_addr[5]));
+
+	/* set rest of 16bit msb and 4bit filter(0xF) */
+	axienet_iow(&lp, XAS_MAC_MSB_OFFSET,
+		    (0xF << XAS_MAC_MSB_FF_MASK_SHIFT) |
+		    (mac_addr[0] << 8) | mac_addr[1]);
+
+	/* now tell the switch which frames to consider as mgmt frames
+	 */
+	/*  DA list
+	 *  01-80-C2-00-00-00 STP 802.1d && LLDP
+	 */
+	memset(&cam, 0, sizeof(struct cam_struct));
+
+	cam.dest_addr[0] = 0x01;
+	cam.dest_addr[1] = 0x80;
+	cam.dest_addr[2] = 0xc2;
+	cam.dest_addr[3] = 0x00;
+	cam.dest_addr[4] = 0x00;
+	cam.dest_addr[5] = 0x00;
+
+	/* send it all, src mac filter will pick the port */
+	cam.fwd_port = DEFAULT_FWD_ALL;
+	cam.flags |= XAS_CAM_EP_MGMTQ_EN;
+	cam.vlanid = DEFAULT_PVID;
+	/* TODO if pvid changes on the port of switch,
+	 * these cam entries have to be updated
+	 */
+
+	if (tsn_switch_cam_set(cam, ADD) < 0)
+		dev_err(&pdev->dev, "could not add default fdb\n");
+
+	/* 01-80-c2-00-00-0e  LLDP */
+	cam.dest_addr[5] = 0x0e;
+	if (tsn_switch_cam_set(cam, ADD) < 0)
+		dev_err(&pdev->dev, "could not add default fdb\n");
+	/* CDP */
+	cam.dest_addr[0] = 0x01;
+	cam.dest_addr[1] = 0x00;
+	cam.dest_addr[2] = 0x0c;
+	cam.dest_addr[3] = 0xcc;
+	cam.dest_addr[4] = 0xcc;
+	cam.dest_addr[5] = 0xcc;
+	if (tsn_switch_cam_set(cam, ADD) < 0)
+		dev_err(&pdev->dev, "could not add default fdb\n");
+
+	/* PTPv2 UDP Announce Messages */
+	cam.dest_addr[0] = 0x01;
+	cam.dest_addr[1] = 0x00;
+	cam.dest_addr[2] = 0x5e;
+	cam.dest_addr[3] = 0x00;
+	cam.dest_addr[4] = 0x01;
+	cam.dest_addr[5] = 0x81;
+	if (tsn_switch_cam_set(cam, ADD) < 0)
+		dev_err(&pdev->dev, "could not add default fdb\n");
+	/* PTPv2 UDP P2P Mechanism Messages */
+	cam.dest_addr[4] = 0x00;
+	cam.dest_addr[5] = 0x6b;
+	if (tsn_switch_cam_set(cam, ADD) < 0)
+		dev_err(&pdev->dev, "could not add default fdb\n");
+
+	/* on RX path enable sideband management on frames forwarded to ep
+	 * this only applicable if IP param EN_INBAND_MGMT_TAG is 0
+	 */
+	val = axienet_ior(&lp, XAS_MNG_Q_CTRL_OFFSET);
+	val |= (1 << XAS_MNG_Q_SIDEBAND_EN_SHIFT);
+	axienet_iow(&lp, XAS_MNG_Q_CTRL_OFFSET, val);
+
+	return 0;
+}
+
+static int tsnswitch_probe(struct platform_device *pdev)
+{
+	struct resource *swt;
+	int ret;
+	u16 num_tc;
+	int data;
+	struct net_device *ndev;
+	int value;
+	u8 inband_mgmt_tag;
+	struct pmap_data pri_info;
+
+	pr_info("TSN Switch probe\n");
+	/* Map device registers */
+	swt = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	lp.regs = devm_ioremap_resource(&pdev->dev, swt);
+	if (IS_ERR(lp.regs))
+		return PTR_ERR(lp.regs);
+
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-tc",
+				   &num_tc);
+	if (ret || (num_tc != 2 && num_tc != 3))
+		num_tc = XAE_MAX_TSN_TC;
+	lp.num_tc = num_tc;
+
+	axienet_get_pcp_mask(&lp, num_tc);
+
+	en_hw_addr_learning = of_property_read_bool(pdev->dev.of_node,
+						    "xlnx,has-hwaddr-learning");
+
+	pr_info("TSN Switch Initializing ....\n");
+	pr_info("TSN Switch hw_addr_learning :%d\n", en_hw_addr_learning);
+
+	ret = tsn_switch_init();
+	if (ret)
+		return ret;
+	pr_info("TSN CAM Initializing ....\n");
+	pri_info.st_pcp_reg = lp.st_pcp;
+	pri_info.res_pcp_reg = lp.res_pcp;
+	ret = set_pmap_config(pri_info);
+	if (ret)
+		return ret;
+	inband_mgmt_tag = of_property_read_bool(pdev->dev.of_node,
+						"xlnx,has-inband-mgmt-tag");
+	/* only support switchdev in sideband management */
+	if (!inband_mgmt_tag) {
+		ret = tsn_switch_fdb_init(pdev);
+		xlnx_switchdev_init();
+	} else {
+		pr_info("TSN IP with inband mgmt: Linux SWITCHDEV turned off\n");
+	}
+
+	/* writing into endpoint extension control register for channel mapping as follows:
+	 *
+	 *	3 traffic classes & EP + switch + Extended EP
+	 *	      +---------+
+	 *	  1   |         |
+	 *    BE-------         |
+	 *	  2   |         |   1
+	 *     ST------         |------BE
+	 *	  3   |         |   2
+	 *   mgmt------         |------RES
+	 *	  4   |         |
+	 *   RES-------         |
+	 *	  5   |         |
+	 * EX-BE-------         |
+	 *	  6   |         |
+	 * EX-ST-------         |
+	 *	  7   |         |
+	 * EX-RES------         |
+	 *	      +---------+
+	 *
+	 *	2 traffic classes & EP + switch + Extended EP
+	 *	      +---------+
+	 *	  1   |         |
+	 *    BE-------         |
+	 *	  2   |         |   1
+	 *    ST-------         |------BE
+	 *	  3   |         |
+	 *   mgmt------         |
+	 *	  4   |         |
+	 * EX-BE-------         |
+	 *	  5   |         |
+	 * EX-ST-------         |
+	 *	      |         |
+	 *	      +---------+
+	 *	3 traffic classes & EP + switch
+	 *	      +---------+
+	 *	  1   |         |
+	 *    BE-------         |
+	 *	  2   |         |   1
+	 *     ST------         |------BE
+	 *	  3   |         |   2
+	 *   mgmt------         |------RES
+	 *	  4   |         |
+	 *   RES-------         |
+	 *	      |         |
+	 *	      +---------+
+	 *
+	 *	2 traffic classes & EP + switch
+	 *	      +---------+
+	 *	  1   |         |
+	 *    BE-------         |
+	 *	  2   |         |   1
+	 *     ST------         |------BE
+	 *	  3   |         |
+	 *   mgmt------         |
+	 *	      |         |
+	 *	      +---------+
+	 */
+	data = axienet_ior(&lp, XAE_EP_EXT_CTRL_OFFSET);
+	pr_info("Data in Endpoint Extension Control Register is %x\n", data);
+	ndev = of_find_net_device_by_node(ep_node);
+	if (!ndev) {
+		pr_info("Defer switch probe as ep is not probed\n");
+		misc_deregister(&switch_dev);
+		xlnx_switchdev_remove();
+		return -EPROBE_DEFER;
+	}
+	ep_lp = netdev_priv(ndev);
+	if (ep_lp->ex_ep) {
+		if (num_tc == 3) {
+			data = (data & XAE_EX_EP_EXT_CTRL_MASK) |
+					XAE_EX_EP_EXT_CTRL_DATA_TC_3;
+			axienet_iow(&lp, XAE_EP_EXT_CTRL_OFFSET, data);
+		}
+		if (num_tc == 2) {
+			data = (data & XAE_EX_EP_EXT_CTRL_MASK) |
+					XAE_EX_EP_EXT_CTRL_DATA_TC_2;
+			axienet_iow(&lp, XAE_EP_EXT_CTRL_OFFSET, data);
+		}
+		/* Enabling endpoint packet switching extension for broadcast and
+		 * multicast packets received from endpoint
+		 */
+		value = axienet_ior(&lp, XAE_MGMT_QUEUING_OPTIONS_OFFSET);
+		value |= XAE_EX_EP_BROADCAST_PKT_SWITCH;
+		value |= XAE_EX_EP_MULTICAST_PKT_SWITCH;
+		axienet_iow(&lp, XAE_MGMT_QUEUING_OPTIONS_OFFSET, value);
+	} else {
+		if (num_tc == 3) {
+			data = (data & XAE_EP_EXT_CTRL_MASK) |
+					XAE_EP_EXT_CTRL_DATA_TC_3;
+			axienet_iow(&lp, XAE_EP_EXT_CTRL_OFFSET, data);
+		}
+		if (num_tc == 2) {
+			data = (data & XAE_EP_EXT_CTRL_MASK) |
+					XAE_EP_EXT_CTRL_DATA_TC_2;
+			axienet_iow(&lp, XAE_EP_EXT_CTRL_OFFSET, data);
+		}
+	}
+
+	return ret;
+}
+
+static int tsnswitch_remove(struct platform_device *pdev)
+{
+	misc_deregister(&switch_dev);
+	xlnx_switchdev_remove();
+	return 0;
+}
+
+static struct platform_driver tsnswitch_driver = {
+	.probe = tsnswitch_probe,
+	.remove = tsnswitch_remove,
+	.driver = {
+		 .name = "xilinx_tsnswitch",
+		 .of_match_table = tsnswitch_of_match,
+	},
+};
+
+module_platform_driver(tsnswitch_driver);
+
+MODULE_DESCRIPTION("Xilinx TSN Switch driver");
+MODULE_AUTHOR("Xilinx");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_switch.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_switch.h
@@ -0,0 +1,479 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Xilinx TSN core switch header
+ *
+ * Copyright (C) 2017 Xilinx, Inc.
+ *
+ * Author: Saurabh Sengar <saurabhs@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef XILINX_TSN_SWITCH_H
+#define XILINX_TSN_SWITCH_H
+
+#include "xilinx_axienet_tsn.h"
+
+/* ioctls */
+#define GET_STATUS_SWITCH			0x16
+#define SET_STATUS_SWITCH			0x17
+#define ADD_CAM_ENTRY				0x18
+#define DELETE_CAM_ENTRY			0x19
+#define PORT_VLAN_MEM_CTRL			0x20
+#define SET_FRAME_TYPE_FIELD			0x21
+#define SET_MAC1_MNGMNT_Q_CONFIG		0x22
+#define SET_MAC2_MNGMNT_Q_CONFIG		0x23
+#define CONFIG_METER_MEM			0x24
+#define CONFIG_GATE_MEM				0x25
+#define PSFP_CONTROL				0x26
+#define GET_STATIC_PSFP_COUNTER			0x27
+#define GET_METER_REG				0x28
+#define GET_STREAM_FLTR_CONFIG			0x29
+#define CONFIG_MEMBER_MEM			0x2A
+#define CONFIG_INGRESS_FLTR			0x2B
+#define FRER_CONTROL				0x2C
+#define GET_STATIC_FRER_COUNTER			0x2D
+#define GET_MEMBER_REG				0x2E
+#define GET_INGRESS_FLTR			0x2F
+#define SET_PORT_STATUS				0x33
+#define GET_PORT_STATUS				0x34
+#define SET_MAC_ADDR_LEARN_CONFIG		0x30
+#define GET_MAC_ADDR_LEARN_CONFIG		0x31
+#define GET_MAC_ADDR_LEARNT_LIST		0x32
+#define ADD_PORT_VLAN				0x35
+#define DEL_PORT_VLAN				0x36
+#define SET_VLAN_MAC_ADDR_LEARN_CONFIG		0x37
+#define GET_VLAN_MAC_ADDR_LEARN_CONFIG		0x38
+#define READ_CAM_ENTRY				0x39
+#define GET_VLAN_MAC_ADDR_LEARN_CONFIG_VLANM	0x3C
+#define SET_PORT_NATIVE_VLAN			0x3A
+#define GET_PORT_NATIVE_VLAN			0x3B
+#define SET_PMAP_CONFIG				0x3D
+
+/* Xilinx Axi Switch Offsets*/
+#define XAS_STATUS_OFFSET			0x00000
+#define XAS_CONTROL_OFFSET			0x00004
+#define XAS_PMAP_OFFSET				0x00008
+#define XAS_MAC_LSB_OFFSET			0x0000C
+#define XAS_MAC_MSB_OFFSET			0x00010
+#define XAS_MAC_MSB_FF_MASK_SHIFT		(16)
+
+#define XAS_EP2MAC_ST_FIFOT_OFFSET		0x00020
+#define XAS_EP2MAC_RE_FIFOT_OFFSET		0x00024
+#define XAS_EP2MAC_BE_FIFOT_OFFSET		0x00028
+#define XAS_MAC2MAC_ST_FIFOT_OFFSET		0x00030
+#define XAS_MAC2MAC_RE_FIFOT_OFFSET		0x00034
+#define XAS_MAC2MAC_BE_FIFOT_OFFSET		0x00038
+#define XAS_EP_PORT_VLAN_OFFSET			0x00040
+#define XAS_MAC_PORT_VLAN_OFFSET		0x00044
+#define XAS_HW_ADDR_LEARN_CTRL_OFFSET		0x00048
+#define XAS_PORT_STATE_CTRL_OFFSET		0x0004c
+#define XAS_FRM_FLTR_TYPE_FIELD_OPT_OFFSET	0x00050
+
+#define XAS_MNG_Q_CTRL_OFFSET			0x00054
+#define XAS_MNG_Q_SRC_MAC_FIL_EN_SHIFT		(4)
+#define XAS_MNG_Q_SIDEBAND_EN_SHIFT		(3)
+
+#define XAS_MAC1_MNG_Q_OPTION_OFFSET		0x00058
+#define XAS_ST_MAX_FRAME_SIZE_OFFSET		0x00060
+#define XAS_RE_MAX_FRAME_SIZE_OFFSET		0x00064
+#define XAS_BE_MAX_FRAME_SIZE_OFFSET		0x00068
+
+/* Memory static counters */
+#define XAS_MEM_STCNTR_CAM_LOOKUP		0x00400
+#define XAS_MEM_STCNTR_MULTCAST			0x00408
+#define XAS_MEM_STCNTR_ERR_MAC1			0x00410
+#define XAS_MEM_STCNTR_ERR_MAC2			0x00418
+#define XAS_MEM_STCNTR_SC_MAC1_EP		0x00420
+#define XAS_MEM_STCNTR_RES_MAC1_EP		0x00428
+#define XAS_MEM_STCNTR_BE_MAC1_EP		0x00430
+#define XAS_MEM_STCNTR_ERR_SC_MAC1_EP		0x00438
+#define XAS_MEM_STCNTR_ERR_RES_MAC1_EP		0x00440
+#define XAS_MEM_STCNTR_ERR_BE_MAC1_EP		0x00448
+#define XAS_MEM_STCNTR_SC_MAC2_EP		0x00458
+#define XAS_MEM_STCNTR_RES_MAC2_EP		0x00460
+#define XAS_MEM_STCNTR_BE_MAC2_EP		0x00468
+#define XAS_MEM_STCNTR_ERR_SC_MAC2_EP		0x00470
+#define XAS_MEM_STCNTR_ERR_RES_MAC2_EP		0x00478
+#define XAS_MEM_STCNTR_ERR_BE_MAC2_EP		0x00480
+#define XAS_MEM_STCNTR_SC_EP_MAC1		0x00490
+#define XAS_MEM_STCNTR_RES_EP_MAC1		0x00498
+#define XAS_MEM_STCNTR_BE_EP_MAC1		0x004A0
+#define XAS_MEM_STCNTR_ERR_SC_EP_MAC1		0x004A8
+#define XAS_MEM_STCNTR_ERR_RES_EP_MAC1		0x004B0
+#define XAS_MEM_STCNTR_ERR_BE_EP_MAC1		0x004B8
+#define XAS_MEM_STCNTR_SC_MAC2_MAC1		0x004C0
+#define XAS_MEM_STCNTR_RES_MAC2_MAC1		0x004C8
+#define XAS_MEM_STCNTR_BE_MAC2_MAC1		0x004D0
+#define XAS_MEM_STCNTR_ERR_SC_MAC2_MAC1		0x004D8
+#define XAS_MEM_STCNTR_ERR_RES_MAC2_MAC1	0x004E0
+#define XAS_MEM_STCNTR_ERR_BE_MAC2_MAC1		0x004E8
+#define XAS_MEM_STCNTR_SC_EP_MAC2		0x004F0
+#define XAS_MEM_STCNTR_RES_EP_MAC2		0x004F8
+#define XAS_MEM_STCNTR_BE_EP_MAC2		0x00500
+#define XAS_MEM_STCNTR_ERR_SC_EP_MAC2		0x00508
+#define XAS_MEM_STCNTR_ERR_RES_EP_MAC2		0x00510
+#define XAS_MEM_STCNTR_ERR_BE_EP_MAC2		0x00518
+#define XAS_MEM_STCNTR_SC_MAC1_MAC2		0x00520
+#define XAS_MEM_STCNTR_RES_MAC1_MAC2		0x00528
+#define XAS_MEM_STCNTR_BE_MAC1_MAC2		0x00530
+#define XAS_MEM_STCNTR_ERR_SC_MAC1_MAC2		0x00538
+#define XAS_MEM_STCNTR_ERR_RES_MAC1_MAC2	0x00540
+#define XAS_MEM_STCNTR_ERR_BE_MAC1_MAC2		0x00548
+
+/* Stream Destination Lookup CAM */
+#define XAS_SDL_CAM_CTRL_OFFSET			0x1000
+#define XAS_SDL_CAM_STATUS_OFFSET		0x1004
+#define XAS_SDL_CAM_KEY1_OFFSET			0x1008
+#define XAS_SDL_CAM_KEY2_OFFSET			0x100C
+#define XAS_SDL_CAM_TV1_OFFSET			0x1010
+#define XAS_SDL_CAM_TV2_OFFSET			0x1014
+#define XAS_SDL_CAM_PORT_ACT_OFFSET		0x1018
+
+/* Port VLAN Membership Memory */
+#define XAS_VLAN_MEMB_CTRL_REG			0x1100
+#define XAS_VLAN_MEMB_DATA_REG			0x1104
+
+/* QCI */
+#define PSFP_CONTROL_OFFSET			0x1200
+#define STREAM_FILTER_CONFIG_OFFSET		0x1204
+#define	STREAM_METER_CIR_OFFSET			0x1208
+#define	STREAM_METER_EIR_OFFSET			0x120C
+#define	STREAM_METER_CBR_OFFSET			0x1210
+#define	STREAM_METER_EBR_OFFSET			0x1214
+
+/* PSFP Statistics Counters */
+#define TOTAL_PSFP_FRAMES_OFFSET		0x2000
+#define FLTR_INGS_PORT_ERR_OFFSET		0x2800
+#define FLTR_STDU_ERR_OFFSET			0x3000
+#define METER_ERR_OFFSET			0x3800
+
+/* CB */
+#define FRER_CONTROL_OFFSET			0x1300
+#define INGRESS_FILTER_OFFSET			0x1304
+#define FRER_CONFIG_REG1			0x1308
+#define FRER_CONFIG_REG2			0x130C
+
+/* FRER Statistics Counters */
+#define TOTAL_FRER_FRAMES_OFFSET		0x4000
+#define FRER_DISCARD_INGS_FLTR_OFFSET		0x4800
+#define FRER_PASS_FRAMES_INDV_OFFSET		0x5000
+#define FRER_DISCARD_FRAMES_INDV_OFFSET		0x5800
+#define FRER_PASS_FRAMES_SEQ_OFFSET		0x6000
+#define FRER_DISCARD_FRAMES_SEQ_OFFSET		0x6800
+#define FRER_ROGUE_FRAMES_SEQ_OFFSET		0x7000
+#define SEQ_RECV_RESETS_OFFSET			0x7800
+
+/* endpoint extension control register */
+#define XAE_EP_EXT_CTRL_OFFSET			0x0058
+#define XAE_MGMT_QUEUING_OPTIONS_OFFSET		0x0054
+#define XAE_EX_EP_BROADCAST_PKT_SWITCH		BIT(7)
+#define XAE_EX_EP_MULTICAST_PKT_SWITCH		BIT(6)
+#define XAE_EX_EP_EXT_CTRL_DATA_TC_3		0x00135419
+#define XAE_EX_EP_EXT_CTRL_DATA_TC_2		0x000DC401
+#define XAE_EP_EXT_CTRL_DATA_TC_3		0x00400419
+#define XAE_EP_EXT_CTRL_DATA_TC_2		0x00400409
+#define XAE_EX_EP_EXT_CTRL_MASK			0xFFE00000
+#define XAE_EP_EXT_CTRL_MASK			0xFF1FF000
+
+/* 64 bit counter*/
+struct static_cntr {
+	u32 msb;
+	u32 lsb;
+};
+
+/*********** QCI Structures **************/
+struct psfp_config {
+	u8 gate_id;
+	u8 meter_id;
+	bool en_meter;
+	bool allow_stream;
+	bool en_psfp;
+	u8 wr_op_type;
+	bool op_type;
+};
+
+struct meter_config {
+	u32 cir;
+	u32 eir;
+	u32 cbr;
+	u32 ebr;
+	u8 mode;
+};
+
+struct stream_filter {
+	u8 in_pid; /* ingress port id*/
+	u16 max_fr_size; /* max frame size*/
+};
+
+/* PSFP Static counter*/
+struct psfp_static_counter {
+	struct static_cntr psfp_fr_count;
+	struct static_cntr err_filter_ins_port;
+	struct static_cntr err_filtr_sdu;
+	struct static_cntr err_meter;
+	unsigned char num;
+};
+
+/* QCI Core stuctures */
+struct qci {
+	struct meter_config meter_config_data;
+	struct stream_filter stream_config_data;
+	struct psfp_config psfp_config_data;
+	struct psfp_static_counter psfp_counter_data;
+};
+
+/************* QCI Structures end *************/
+
+/*********** CB Structures **************/
+struct frer_ctrl {
+	u8 gate_id;
+	u8 memb_id;
+	bool seq_reset;
+	bool gate_state;
+	bool rcvry_tmout;
+	bool frer_valid;
+	u8 wr_op_type;
+	bool op_type;
+};
+
+struct in_fltr {
+	u8 in_port_id;
+	u16 max_seq_id;
+};
+
+struct frer_memb_config {
+	u8 seq_rec_hist_len;
+	u8 split_strm_egport_id;
+	u16 split_strm_vlan_id;
+	u32 rem_ticks;
+};
+
+/* FRER Static counter*/
+struct frer_static_counter {
+	struct static_cntr frer_fr_count;
+	struct static_cntr disc_frames_in_portid;
+	struct static_cntr pass_frames_seq_recv;
+	struct static_cntr disc_frames_seq_recv;
+	struct static_cntr rogue_frames_seq_recv;
+	struct static_cntr pass_frames_ind_recv;
+	struct static_cntr disc_frames_ind_recv;
+	struct static_cntr seq_recv_rst;
+	unsigned char num;
+};
+
+/* CB Core stuctures */
+struct cb {
+	struct frer_ctrl frer_ctrl_data;
+	struct in_fltr in_fltr_data;
+	struct frer_memb_config frer_memb_config_data;
+	struct frer_static_counter frer_counter_data;
+};
+
+/************* CB Structures end *************/
+
+/********* Switch Structures Starts ***********/
+struct thershold {
+	u16 t1;
+	u16 t2;
+};
+
+struct pmap_data {
+	int st_pcp_reg;
+	int res_pcp_reg;
+};
+
+/* memory static counters */
+struct mem_static_arr_cntr {
+	struct static_cntr cam_lookup;
+	struct static_cntr multicast_fr;
+	struct static_cntr err_mac1;
+	struct static_cntr err_mac2;
+	struct static_cntr sc_mac1_ep;
+	struct static_cntr res_mac1_ep;
+	struct static_cntr be_mac1_ep;
+	struct static_cntr err_sc_mac1_ep;
+	struct static_cntr err_res_mac1_ep;
+	struct static_cntr err_be_mac1_ep;
+	struct static_cntr sc_mac2_ep;
+	struct static_cntr res_mac2_ep;
+	struct static_cntr be_mac2_ep;
+	struct static_cntr err_sc_mac2_ep;
+	struct static_cntr err_res_mac2_ep;
+	struct static_cntr err_be_mac2_ep;
+	struct static_cntr sc_ep_mac1;
+	struct static_cntr res_ep_mac1;
+	struct static_cntr be_ep_mac1;
+	struct static_cntr err_sc_ep_mac1;
+	struct static_cntr err_res_ep_mac1;
+	struct static_cntr err_be_ep_mac1;
+	struct static_cntr sc_mac2_mac1;
+	struct static_cntr res_mac2_mac1;
+	struct static_cntr be_mac2_mac1;
+	struct static_cntr err_sc_mac2_mac1;
+	struct static_cntr err_res_mac2_mac1;
+	struct static_cntr err_be_mac2_mac1;
+	struct static_cntr sc_ep_mac2;
+	struct static_cntr res_ep_mac2;
+	struct static_cntr be_ep_mac2;
+	struct static_cntr err_sc_ep_mac2;
+	struct static_cntr err_res_ep_mac2;
+	struct static_cntr err_be_ep_mac2;
+	struct static_cntr sc_mac1_mac2;
+	struct static_cntr res_mac1_mac2;
+	struct static_cntr be_mac1_mac2;
+	struct static_cntr err_sc_mac1_mac2;
+	struct static_cntr err_res_mac1_mac2;
+	struct static_cntr err_be_mac1_mac2;
+};
+
+#define XAS_CAM_IPV_EN		BIT(0)
+#define XAS_CAM_EP_MGMTQ_EN	BIT(1)
+#define XAS_CAM_VALID		BIT(2)
+
+/* CAM structure */
+struct cam_struct {
+	u8 src_addr[6];
+	u8 dest_addr[6];
+	u16 vlanid;
+	u16 tv_vlanid;
+	u8 fwd_port;
+	u8 gate_id;
+	u8 ipv;
+	u32 flags;
+	u8 ep_port_act;
+	u8 mac_port_act;
+};
+
+/*Frame Filtering Type Field Option */
+struct ff_type {
+	u16 type1;
+	u16 type2;
+};
+
+/* TODO Fix holes in this structure and corresponding TSN switch_prog app */
+struct mac_addr_learn {
+	bool aging;
+	bool is_age;
+	bool learning;
+	bool is_learn;
+	bool learn_untag;
+	bool is_untag;
+	u32 aging_time;
+};
+
+struct mac_learnt {
+	u8 mac_addr[6];
+	u16 vlan_id;
+};
+
+#define MAX_NUM_MAC_ENTRIES	2048
+struct mac_addr_list {
+	u8 port_num;
+	u16 num_list;
+	struct mac_learnt list[MAX_NUM_MAC_ENTRIES];
+};
+
+struct port_status {
+	u8 port_num;
+	u8 port_status;
+};
+
+struct port_vlan {
+	bool aging;
+	bool is_age;
+	bool learning;
+	bool is_learn;
+	bool is_mgmtq;
+	bool en_ipv;
+	bool en_port_status;
+	u8 mgmt_ext_id;
+	u8 port_num;
+	u8 ipv;
+	u8 port_status;
+	u16 vlan_id;
+	u32 aging_time;
+};
+
+struct native_vlan {
+	bool en_ipv;
+	u8 port_num;
+	u8 ipv;
+	u16 vlan_id;
+};
+
+enum switch_port {
+	PORT_EP = 1,
+	PORT_MAC1 = 2,
+	PORT_MAC2 = 4,
+	PORT_EX_ONLY = 8,
+	PORT_EX_EP = 16,
+};
+
+/* Core switch structure*/
+/* TODO Fix holes in this structure and corresponding TSN switch_prog app */
+struct switch_data {
+	u32 switch_status;
+	u32 switch_ctrl;
+	u32 switch_prt;
+	u8 sw_mac_addr[6];
+	/*0 - schedule, 1 - reserved, 2 - best effort queue*/
+	struct thershold thld_ep_mac[3];
+	struct thershold thld_mac_mac[3];
+	u32 ep_vlan;
+	u32 mac_vlan;
+	u32 max_frame_sc_que;
+	u32 max_frame_res_que;
+	u32 max_frame_be_que;
+	/* Memory counters */
+	struct mem_static_arr_cntr mem_arr_cnt;
+	/* CAM */
+	struct cam_struct cam_data;
+/* Frame Filtering Type Field Option */
+	struct ff_type typefield;
+/* MAC Port-1 Management Queueing Options */
+	int mac1_config;
+/* MAC Port-2 Management Queueing Options */
+	int mac2_config;
+/* Port VLAN Membership Registers */
+	int port_vlan_mem_ctrl;
+	char port_vlan_mem_data;
+};
+
+/********* Switch Structures ends ***********/
+
+extern struct axienet_local lp;
+
+/********* qci function declararions ********/
+void psfp_control(struct psfp_config data);
+void config_stream_filter(struct stream_filter data);
+void program_meter_reg(struct meter_config data);
+void get_psfp_static_counter(struct psfp_static_counter *data);
+void get_meter_reg(struct meter_config *data);
+void get_stream_filter_config(struct stream_filter *data);
+
+/********* cb function declararions ********/
+void frer_control(struct frer_ctrl data);
+void get_ingress_filter_config(struct in_fltr *data);
+void config_ingress_filter(struct cb data);
+void get_member_reg(struct frer_memb_config *data);
+void program_member_reg(struct cb data);
+void get_frer_static_counter(struct frer_static_counter *data);
+int tsn_switch_cam_set(struct cam_struct data, u8 add);
+u8 *tsn_switch_get_id(void);
+int tsn_switch_set_stp_state(struct port_status *port);
+int tsn_switch_vlan_add(struct port_vlan *port, int add);
+int tsn_switch_pvid_get(struct native_vlan *port);
+int tsn_switch_pvid_add(struct native_vlan *port);
+#ifdef CONFIG_XILINX_TSN_SWITCH
+int xlnx_switchdev_init(void);
+void xlnx_switchdev_remove(void);
+#endif
+#endif /* XILINX_TSN_SWITCH_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_switchdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_switchdev.c
@@ -0,0 +1,374 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx TSN Switch Device support driver
+ *
+ * Copyright (c) 2022 Xilinx, Inc. All rights reserved.
+ */
+#ifdef CONFIG_XILINX_TSN_SWITCH
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/if_bridge.h>
+#include <net/switchdev.h>
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_switch.h"
+
+#define tsn_to_linux_sw_state(s) \
+	(((s) == BR_STATE_DISABLED)   ? TSN_SW_STATE_DISABLED : \
+	 ((s) == BR_STATE_BLOCKING)   ? TSN_SW_STATE_BLOCKING : \
+	 ((s) == BR_STATE_LISTENING)  ? TSN_SW_STATE_LISTENING : \
+	 ((s) == BR_STATE_LEARNING)   ? TSN_SW_STATE_LEARNING : \
+	 ((s) == BR_STATE_FORWARDING) ? TSN_SW_STATE_FORWARDING : \
+	 TSN_SW_STATE_DISABLED)
+
+#define stp_state_string(s) \
+	(((s) == BR_STATE_DISABLED)   ? "disabled" : \
+	 ((s) == BR_STATE_BLOCKING)   ? "blocking" : \
+	 ((s) == BR_STATE_LISTENING)  ? "listening" : \
+	 ((s) == BR_STATE_LEARNING)   ? "learning" : \
+	 ((s) == BR_STATE_FORWARDING) ? "forwarding" : \
+	 "und_blocked")
+
+#define TSN_SW_STATE_DISABLED		0
+#define TSN_SW_STATE_BLOCKING		1
+#define TSN_SW_STATE_LISTENING		2
+#define TSN_SW_STATE_LEARNING		3
+#define TSN_SW_STATE_FORWARDING		4
+#define TSN_SW_STATE_FLUSH		5
+
+static struct workqueue_struct *xlnx_sw_owq;
+static int
+xlnx_switchdev_port_attr_set_event(struct net_device *netdev,
+				   struct switchdev_notifier_port_attr_info *port_attr_info);
+
+static int xlnx_switch_fdb_set(struct axienet_local *lp,
+			       struct switchdev_notifier_fdb_info *fdb_info,
+			       bool adding)
+{
+	struct cam_struct data;
+
+	memset(&data, 0, sizeof(struct cam_struct));
+	data.fwd_port = lp->switch_prt;
+	ether_addr_copy((u8 *)&data.dest_addr, fdb_info->addr);
+	data.vlanid = fdb_info->vid;
+
+	return tsn_switch_cam_set(data, adding);
+}
+
+struct xlnx_switchdev_event_work {
+	struct work_struct work;
+	struct switchdev_notifier_fdb_info fdb_info;
+	struct axienet_local *lp;
+	unsigned long event;
+};
+
+static void xlnx_sw_fdb_offload_notify(struct axienet_local *lp,
+				       struct switchdev_notifier_fdb_info *recv_info)
+{
+	struct switchdev_notifier_fdb_info info;
+
+	info.addr = recv_info->addr;
+	info.vid = recv_info->vid;
+	call_switchdev_notifiers(SWITCHDEV_FDB_OFFLOADED,
+				 lp->ndev, &info.info, NULL);
+}
+
+static int xlnx_sw_port_obj_vlan_add(struct axienet_local *lp,
+				     const struct switchdev_obj_port_vlan *vlan)
+{
+	struct port_vlan pvl;
+	struct native_vlan nvl;
+	bool flag_pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
+	u16 vid;
+	int err;
+
+	memset(&nvl, 0, sizeof(struct native_vlan));
+	memset(&pvl, 0, sizeof(struct port_vlan));
+
+	pvl.port_num = lp->switch_prt;
+	nvl.port_num = lp->switch_prt;
+
+	/* TODO deal with vlan->flags for PVID and untagged */
+	vid = vlan->vid;
+	if (flag_pvid) {
+		nvl.vlan_id = vid;
+		err = tsn_switch_pvid_add(&nvl);
+	} else {
+		pvl.vlan_id = vid;
+		err = tsn_switch_vlan_add(&pvl, true);
+	}
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static int xlnx_sw_port_obj_vlan_del(struct axienet_local *lp,
+				     const struct switchdev_obj_port_vlan *vlan)
+{
+	struct port_vlan pvl;
+	struct native_vlan nvl;
+	u16 vid;
+	int err;
+
+	memset(&nvl, 0, sizeof(struct native_vlan));
+	memset(&pvl, 0, sizeof(struct port_vlan));
+
+	pvl.port_num = lp->switch_prt;
+	nvl.port_num = lp->switch_prt;
+
+	tsn_switch_pvid_get(&nvl);
+
+	vid = vlan->vid;
+	if (vid == nvl.vlan_id) {
+		nvl.vlan_id = 1;
+		err = tsn_switch_pvid_add(&nvl);
+	} else {
+		pvl.vlan_id = vid;
+		err = tsn_switch_vlan_add(&pvl, false);
+	}
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static int xlnx_sw_obj_add(struct net_device *ndev,
+			   const struct switchdev_obj *obj)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int err = 0;
+
+	switch (obj->id) {
+	case SWITCHDEV_OBJ_ID_PORT_VLAN:
+		err = xlnx_sw_port_obj_vlan_add(lp,
+						SWITCHDEV_OBJ_PORT_VLAN(obj));
+		break;
+	default:
+		err = -EOPNOTSUPP;
+		break;
+	}
+
+	return err;
+}
+
+static int xlnx_sw_obj_del(struct net_device *ndev,
+			   const struct switchdev_obj *obj)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int err = 0;
+
+	switch (obj->id) {
+	case SWITCHDEV_OBJ_ID_PORT_VLAN:
+		err = xlnx_sw_port_obj_vlan_del(lp,
+						SWITCHDEV_OBJ_PORT_VLAN(obj));
+		break;
+	default:
+		err = -EOPNOTSUPP;
+		break;
+	}
+
+	return err;
+}
+
+static void xlnx_switchdev_event_work(struct work_struct *work)
+{
+	struct xlnx_switchdev_event_work *switchdev_work =
+		container_of(work, struct xlnx_switchdev_event_work, work);
+	struct axienet_local *lp = switchdev_work->lp;
+	struct switchdev_notifier_fdb_info *fdb_info;
+	int err;
+
+	rtnl_lock();
+	switch (switchdev_work->event) {
+	case SWITCHDEV_FDB_ADD_TO_DEVICE:
+		fdb_info = &switchdev_work->fdb_info;
+		err = xlnx_switch_fdb_set(lp, fdb_info, true);
+		if (err) {
+			netdev_dbg(lp->ndev, "fdb add failed err=%d\n", err);
+			break;
+		}
+		xlnx_sw_fdb_offload_notify(lp, fdb_info);
+		break;
+	case SWITCHDEV_FDB_DEL_TO_DEVICE:
+		fdb_info = &switchdev_work->fdb_info;
+		err = xlnx_switch_fdb_set(lp, fdb_info, false);
+		if (err) {
+			netdev_dbg(lp->ndev, "fdb add failed err=%d\n", err);
+			break;
+		}
+		break;
+	}
+	rtnl_unlock();
+
+	kfree(switchdev_work->fdb_info.addr);
+	kfree(switchdev_work);
+	dev_put(lp->ndev);
+}
+
+static int xlnx_switchdev_event(struct notifier_block *unused,
+				unsigned long event, void *ptr)
+{
+	struct net_device *dev = switchdev_notifier_info_to_dev(ptr);
+	struct switchdev_notifier_fdb_info *fdb_info = ptr;
+	struct xlnx_switchdev_event_work *switchdev_work;
+	struct axienet_local *lp;
+
+	lp = netdev_priv(dev);
+	switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC);
+	if (!switchdev_work)
+		return NOTIFY_BAD;
+
+	if (event == SWITCHDEV_PORT_ATTR_SET)
+		return xlnx_switchdev_port_attr_set_event(dev, ptr);
+
+	INIT_WORK(&switchdev_work->work, xlnx_switchdev_event_work);
+	switchdev_work->lp = lp;
+	switchdev_work->event = event;
+
+	switch (event) {
+	case SWITCHDEV_FDB_ADD_TO_DEVICE:
+	case SWITCHDEV_FDB_DEL_TO_DEVICE:
+		memcpy(&switchdev_work->fdb_info, ptr,
+		       sizeof(switchdev_work->fdb_info));
+		switchdev_work->fdb_info.addr = kzalloc(ETH_ALEN, GFP_ATOMIC);
+		ether_addr_copy((u8 *)switchdev_work->fdb_info.addr,
+				fdb_info->addr);
+		/* take a reference on the switch port dev */
+		dev_hold(dev);
+		break;
+	default:
+		kfree(switchdev_work);
+		return NOTIFY_DONE;
+	}
+
+	queue_work(xlnx_sw_owq, &switchdev_work->work);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block xlnx_switchdev_notifier = {
+	.notifier_call = xlnx_switchdev_event,
+};
+
+static int
+xlnx_switchdev_port_obj_event(unsigned long event, struct net_device *netdev,
+			      struct switchdev_notifier_port_obj_info *port_obj_info)
+{
+	int err = -EOPNOTSUPP;
+
+	switch (event) {
+	case SWITCHDEV_PORT_OBJ_ADD:
+		err = xlnx_sw_obj_add(netdev, port_obj_info->obj);
+		break;
+	case SWITCHDEV_PORT_OBJ_DEL:
+		err = xlnx_sw_obj_del(netdev, port_obj_info->obj);
+		break;
+	}
+
+	port_obj_info->handled = true;
+
+	return notifier_from_errno(err);
+}
+
+static int xlnx_switchdev_blocking_event(struct notifier_block *unused, unsigned long event,
+					 void *ptr)
+{
+	struct net_device *dev = switchdev_notifier_info_to_dev(ptr);
+
+	switch (event) {
+	case SWITCHDEV_PORT_OBJ_ADD:
+	case SWITCHDEV_PORT_OBJ_DEL:
+		return xlnx_switchdev_port_obj_event(event, dev, ptr);
+	case SWITCHDEV_PORT_ATTR_SET:
+		return xlnx_switchdev_port_attr_set_event(dev, ptr);
+	}
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block xlnx_switchdev_blocking_notifier = {
+	.notifier_call = xlnx_switchdev_blocking_event,
+};
+
+static int xlnx_sw_port_attr_stp_state_set(struct axienet_local *lp, u8 state)
+{
+	struct port_status ps;
+
+	ps.port_num = lp->switch_prt;
+	ps.port_status = tsn_to_linux_sw_state(state);
+
+	return tsn_switch_set_stp_state(&ps);
+}
+
+static int xlnx_sw_port_attr_pre_bridge_flags_set(struct axienet_local *lp,
+						  struct switchdev_brport_flags brport_flags)
+{
+	if (brport_flags.mask & ~(BR_LEARNING | BR_FLOOD))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int xlnx_sw_attr_set(struct net_device *ndev,
+			    const struct switchdev_attr *attr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	int err = 0;
+
+	switch (attr->id) {
+	case SWITCHDEV_ATTR_ID_PORT_STP_STATE:
+		err = xlnx_sw_port_attr_stp_state_set(lp,
+						      attr->u.stp_state);
+		break;
+	case SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS:
+		pr_info("received request to SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: %lu\n",
+			attr->u.brport_flags.val);
+		break;
+	case SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS:
+		err = xlnx_sw_port_attr_pre_bridge_flags_set(lp, attr->u.brport_flags);
+		break;
+	case SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME:
+		break;
+	case SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING:
+		break;
+	default:
+		pr_info("%s: unhandled id: %d\n", __func__, attr->id);
+		err = -EOPNOTSUPP;
+		break;
+	}
+
+	return err;
+}
+
+static int
+xlnx_switchdev_port_attr_set_event(struct net_device *netdev,
+				   struct switchdev_notifier_port_attr_info *port_attr_info)
+{
+	int err;
+
+	err = xlnx_sw_attr_set(netdev, port_attr_info->attr);
+
+	port_attr_info->handled = true;
+
+	return notifier_from_errno(err);
+}
+
+int xlnx_switchdev_init(void)
+{
+	xlnx_sw_owq = alloc_ordered_workqueue("%s_ordered", WQ_MEM_RECLAIM,
+					      "xlnx_sw");
+	if (!xlnx_sw_owq)
+		return -ENOMEM;
+	register_switchdev_notifier(&xlnx_switchdev_notifier);
+	register_switchdev_blocking_notifier(&xlnx_switchdev_blocking_notifier);
+
+	return 0;
+}
+
+void xlnx_switchdev_remove(void)
+{
+	destroy_workqueue(xlnx_sw_owq);
+	unregister_switchdev_notifier(&xlnx_switchdev_notifier);
+	unregister_switchdev_blocking_notifier(&xlnx_switchdev_blocking_notifier);
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_tadma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_tadma.c
@@ -0,0 +1,735 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Xilinx FPGA Xilinx TADMA driver.
+ *
+ * Copyright (C) 2018 Xilinx, Inc. All rights reserved.
+ *
+ * Author: Syed Syed <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/list.h>
+#include <linux/hash.h>
+#include "xilinx_axienet_tsn.h"
+#include "xilinx_tsn_tadma.h"
+
+/* max packets that can be sent in a time trigger */
+#define MAX_TRIG_COUNT 4
+
+/* This driver assumes the num_streams configured in HW is always 2^n */
+
+typedef u32 pm_entry_t;
+
+struct tadma_stream {
+	u8 dmac[6];
+	short vid;
+	u32 trigger;
+	u32 count;
+	u8 start;
+};
+
+static u8  tadma_hash_bits;
+struct tadma_stream_entry {
+	u8 macvlan[8];
+	u32 tticks;
+	struct hlist_node hash_link;
+	int sid;
+	int sfm;
+	int count;
+};
+
+static u32 get_sid;
+static u32 get_sfm;
+#define sfm_entry_offset(lp, sid) \
+	((lp->active_sfm == SFM_UPPER) ? \
+	(XTADMA_USFM_OFFSET) +  ((sid) * sizeof(struct sfm_entry)) : \
+	(XTADMA_LSFM_OFFSET) +  ((sid) * sizeof(struct sfm_entry)))
+
+#define STRID_BE 0
+
+static inline u32 tadma_macvlan_hash(const unsigned char *addr)
+{
+	u64 value = get_unaligned((u64 *)addr);
+
+	return hash_64(value, tadma_hash_bits);
+}
+
+static inline bool mac_vlan_equal(const u8 addr1[8],
+				  const u8 addr2[8])
+{
+	const u16 *a = (const u16 *)addr1;
+	const u16 *b = (const u16 *)addr2;
+	bool ret = 1;
+
+	if ((a[0] ^ b[0]) | (a[1] ^ b[1]) |
+		(a[2] ^ b[2]) | (a[3] ^ a[3])) {
+		ret = 0;
+	}
+
+	return ret;
+}
+
+static struct tadma_stream_entry *tadma_hash_lookup_stream(struct hlist_head *head,
+							   const unsigned char *mac_vlan)
+{
+	struct tadma_stream_entry *entry;
+
+	hlist_for_each_entry(entry, head, hash_link) {
+		if (mac_vlan_equal(entry->macvlan, mac_vlan))
+			return entry;
+	}
+
+	return NULL;
+}
+
+static u32 tadma_stream_alm_offset_irq(int sid, u32 tx_bd_rd, struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 alm_offset;
+
+	alm_offset = XTADMA_ALM_OFFSET +
+		sid * sizeof(struct alm_entry) * lp->num_tadma_buffers;
+
+	return alm_offset + (tx_bd_rd * sizeof(struct alm_entry));
+}
+
+static void tadma_xmit_done(struct net_device *ndev, u8 sid, u32 cnt)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 size = 0, packets = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&lp->tadma_tx_lock, flags);
+
+	if (lp->tx_bd_head[sid] == lp->tx_bd_tail[sid]) {
+		spin_unlock_irqrestore(&lp->tadma_tx_lock, flags);
+		return;
+	}
+
+	while ((lp->tx_bd_head[sid] != lp->tx_bd_tail[sid]) && cnt) {
+		if (lp->tx_bd[sid][lp->tx_bd_tail[sid]].tx_desc_mapping ==
+		    DESC_DMA_MAP_PAGE) {
+			dma_unmap_page(ndev->dev.parent,
+				       lp->tx_bd[sid][lp->tx_bd_tail[sid]].phys,
+				       lp->tx_bd[sid][lp->tx_bd_tail[sid]].len,
+				       DMA_TO_DEVICE);
+		} else {
+			dma_unmap_single(ndev->dev.parent,
+					 lp->tx_bd[sid][lp->tx_bd_tail[sid]].
+					 phys,
+					 lp->tx_bd[sid][lp->tx_bd_tail[sid]].
+					 len,
+					 DMA_TO_DEVICE);
+		}
+		if (lp->tx_bd[sid][lp->tx_bd_tail[sid]].tx_skb) {
+			dev_kfree_skb_irq((struct sk_buff *)
+					  lp->tx_bd[sid][lp->tx_bd_tail[sid]].
+					  tx_skb);
+		}
+
+		size += lp->tx_bd[sid][lp->tx_bd_tail[sid]].len;
+		packets++;
+		lp->tx_bd_tail[sid]++;
+		lp->tx_bd_tail[sid] %= lp->num_tadma_buffers;
+		cnt--;
+	}
+
+	ndev->stats.tx_packets += packets;
+	ndev->stats.tx_bytes += size;
+	spin_unlock_irqrestore(&lp->tadma_tx_lock, flags);
+}
+
+static irqreturn_t tadma_irq(int irq, void *_ndev)
+{
+	struct axienet_local *lp = netdev_priv(_ndev);
+	struct alm_entry alm;
+	u32 status, sid = 0, alm_offset;
+	int cnt = 0;
+
+	status = tadma_ior(lp, XTADMA_INT_STA_OFFSET);
+
+	/* clear interrupt */
+	tadma_iow(lp, XTADMA_INT_CLR_OFFSET, status);
+
+	if (status & XTADMA_FFI_INT_EN) {
+		for (sid = 0; sid < lp->num_streams; sid++) {
+			cnt = 0;
+			alm_offset = tadma_stream_alm_offset_irq(sid, lp->tx_bd_rd[sid], _ndev);
+			alm.cfg = tadma_ior(lp, alm_offset + 4);
+			while (((alm.cfg & XTADMA_ALM_UFF) == 0) &&
+			       (cnt < lp->num_tadma_buffers) &&
+			       (lp->tx_bd_rd[sid] != lp->tx_bd_head[sid])) {
+				lp->tx_bd_rd[sid]++;
+				lp->tx_bd_rd[sid] = lp->tx_bd_rd[sid] % lp->num_tadma_buffers;
+				alm_offset = tadma_stream_alm_offset_irq(sid,
+									 lp->tx_bd_rd[sid], _ndev);
+				alm.cfg = tadma_ior(lp, alm_offset + 4);
+				cnt++;
+			}
+			if (cnt)
+				tadma_xmit_done(_ndev, sid, cnt);
+		}
+	}
+	netif_tx_wake_all_queues(_ndev);
+
+	return IRQ_HANDLED;
+}
+
+static int tadma_sfm_hash_init(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct tadma_cb *cb;
+	int i;
+
+	cb = kzalloc(sizeof(*cb), GFP_KERNEL);
+	if (!cb)
+		return -ENOMEM;
+
+	cb->stream_hash = kcalloc(lp->num_entries, sizeof(struct hlist_head *),
+				  GFP_KERNEL);
+
+	if (!cb->stream_hash) {
+		kfree(cb);
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < lp->num_entries; i++)
+		INIT_HLIST_HEAD(&cb->stream_hash[i]);
+
+	lp->t_cb = cb;
+
+	return 0;
+}
+
+static void tadma_sfm_program(struct net_device *ndev,
+			      int sid, u32 tticks, u32 count)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct sfm_entry sfm = {0, };
+	u32 offset;
+
+	pr_debug("%s entry: %d, count: %d\n", __func__, sid, count);
+	offset = sfm_entry_offset(lp, sid);
+
+	/* each tick is 8ns */
+	sfm.tticks = tticks / 8;
+
+	/*clear strid and queue type */
+	sfm.cfg &= ~(XTADMA_STR_ID_MASK | XTADMA_STR_QUE_TYPE_MASK);
+
+	sfm.cfg |= (sid << XTADMA_STR_ID_SHIFT) & XTADMA_STR_ID_MASK;
+	sfm.cfg |= (qt_st << XTADMA_STR_QUE_TYPE_SHIFT) &
+		   XTADMA_STR_QUE_TYPE_MASK;
+	if (count != 0)
+		sfm.cfg &= ~XTADMA_STR_CONT_FETCH_EN;
+	else
+		sfm.cfg |= XTADMA_STR_CONT_FETCH_EN;
+	sfm.cfg |= XTADMA_STR_ENTRY_VALID;
+
+	count  = (count > 0) ? (count - 1) : count;
+	/* hw xmits 1 more than what is programmed, so use count */
+	sfm.cfg |= (count << XTADMA_STR_NUM_FRM_SHIFT) &
+			XTADMA_STR_NUM_FRM_MASK;
+	pr_debug("sfm cfg: %x\n", sfm.cfg);
+	tadma_iow(lp, offset, sfm.tticks);
+	tadma_iow(lp, offset + 4, sfm.cfg);
+}
+
+static int tadma_sfm_init(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	lp->active_sfm = SFM_UPPER;
+
+	tadma_sfm_program(ndev, STRID_BE, NSEC_PER_MSEC, 0);
+
+	return 0;
+}
+
+int axienet_tadma_stop(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u8 i = 0;
+
+	for (i = 0; i < lp->num_streams ; i++)
+		kfree(lp->tx_bd[i]);
+
+	kfree(lp->tx_bd);
+
+	free_irq(lp->tadma_irq, ndev);
+
+	return 0;
+}
+
+int axienet_tadma_open(struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 cr;
+	u8 i = 0;
+	int ret;
+	static char irq_name[24];
+
+	if (lp->tadma_irq) {
+		sprintf(irq_name, "%s_tadma_tx", ndev->name);
+		ret = request_irq(lp->tadma_irq, tadma_irq, IRQF_SHARED,
+				  irq_name, ndev);
+		if (ret)
+			return ret;
+	}
+	pr_debug("%s TADMA irq %d\n", __func__, lp->tadma_irq);
+
+	/* enable all interrupts */
+	tadma_iow(lp, XTADMA_INT_EN_OFFSET, XTADMA_FFI_INT_EN |
+		  XTADMA_IE_INT_EN);
+
+	tadma_sfm_init(ndev);
+	tadma_sfm_hash_init(ndev);
+	cr = XTADMA_CFG_DONE;
+	tadma_iow(lp, XTADMA_CR_OFFSET, cr);
+
+	lp->tx_bd = kmalloc_array(lp->num_streams, sizeof(struct axitadma_bd *),
+				  GFP_KERNEL);
+	if (!lp->tx_bd)
+		ret = -ENOMEM;
+
+	for (i = 0; i < lp->num_streams ; i++) {
+		lp->tx_bd_head[i] = 0;
+		lp->tx_bd_tail[i] = 0;
+		lp->tx_bd_rd[i] = 0;
+		lp->tx_bd[i] = kmalloc_array(lp->num_tadma_buffers,
+					     sizeof(*lp->tx_bd[i]), GFP_KERNEL);
+		if (!lp->tx_bd[i])
+			return -ENOMEM;
+	}
+
+	return ret;
+}
+
+/*TODO: Fix TADMA probe error handling path */
+int __maybe_unused axienet_tadma_probe(struct platform_device *pdev,
+				       struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct resource tadma_res;
+	struct device_node *np;
+	u16 num_tc = XAE_MAX_TSN_TC;
+	u8 count = 0;
+	int ret;
+
+	ret = of_property_read_u16(pdev->dev.of_node, "xlnx,num-tc",
+				   &num_tc);
+	np = of_parse_phandle(pdev->dev.of_node, "axistream-connected-tx",
+			      num_tc - 1);
+
+	if (np) {
+		ret = of_address_to_resource(np, 0, &tadma_res);
+		if (ret >= 0)
+			lp->tadma_regs = devm_ioremap_resource(&pdev->dev,
+							       &tadma_res);
+		else
+			return -ENODEV;
+	} else {
+		return -ENODEV;
+	}
+
+	lp->tadma_irq = irq_of_parse_and_map(np, 0);
+
+	ret = of_property_read_u32(np, "xlnx,num-buffers-per-stream",
+				   &lp->num_tadma_buffers);
+	if (ret)
+		lp->num_tadma_buffers = 64;
+
+	ret = of_property_read_u32(np, "xlnx,num-streams", &lp->num_streams);
+	if (ret)
+		lp->num_streams = 8;
+	ret = of_property_read_u32(np, "xlnx,num-fetch-entries",
+				   &lp->num_entries);
+	if (ret)
+		lp->num_entries = 8;
+
+	while (!((lp->num_streams >> count) & 1))
+		count++;
+
+	tadma_hash_bits = count;
+	pr_debug("%s num_stream: %d hash_bits: %d\n", __func__, lp->num_streams,
+		 tadma_hash_bits);
+	pr_info("TADMA probe done\n");
+	spin_lock_init(&lp->tadma_tx_lock);
+	of_node_put(np);
+
+	return 0;
+}
+
+static inline void tadma_pm_inc(int sid, struct axienet_local *lp)
+{
+	pm_entry_t pm;
+	u32 offset;
+	u8 wr;
+
+	offset = XTADMA_PM_OFFSET + (sid * sizeof(pm_entry_t));
+	pm = tadma_ior(lp, offset);
+	wr = (pm & XTADMA_PM_WR_MASK) >> XTADMA_PM_WR_SHIFT;
+	wr = (wr + 1) % lp->num_tadma_buffers;
+	pm &= ~XTADMA_PM_WR_MASK;
+	pm |= (wr << XTADMA_PM_WR_SHIFT);
+
+	tadma_iow(lp, offset, pm);
+}
+
+static int axienet_check_pm_space(int sid, int num_frag,
+				  u32 wr, u32 rd, int total)
+{
+	int avail;
+
+	avail = rd - wr;
+
+	if (avail < 0)
+		avail = total + avail;
+
+	return (avail >= num_frag);
+}
+
+static int tadma_get_strid(struct sk_buff *skb,
+			   struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct tadma_cb *cb = lp->t_cb;
+	struct tadma_stream_entry *entry;
+	struct vlan_ethhdr *vhdr = (struct vlan_ethhdr *)skb->data;
+	int sid = -1; /* BE entry is always 0 */
+	u32 idx;
+	u16 vlan_tci;
+	u8 mac_vlan[8];
+
+	if (!get_sid)
+		return 0;
+
+	memcpy(mac_vlan, vhdr->h_dest, 6);
+
+	vlan_tci = ntohs(vhdr->h_vlan_TCI);
+
+	mac_vlan[6] = (vlan_tci >> 8) & 0x0f;
+	mac_vlan[7] = (vlan_tci & 0xff);
+
+	idx = tadma_macvlan_hash(mac_vlan);
+	entry = tadma_hash_lookup_stream(&cb->stream_hash[idx],
+					 mac_vlan);
+	if (entry)
+		return entry->sid;
+
+	return sid;
+}
+
+static u32 tadma_stream_alm_offset(int sid, u32 wr, struct net_device *ndev)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	u32 alm_offset;
+
+	alm_offset = XTADMA_ALM_OFFSET +
+		sid * sizeof(struct alm_entry) * lp->num_tadma_buffers;
+
+	wr = (wr + lp->num_tadma_buffers - 1) & (lp->num_tadma_buffers - 1);
+
+	return alm_offset + (wr * sizeof(struct alm_entry));
+}
+
+int axienet_tadma_xmit(struct sk_buff *skb, struct net_device *ndev,
+		       u16 queue_type)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct alm_entry alm, alm_fframe = {0};
+	dma_addr_t phys_addr;
+	pm_entry_t pm;
+	u32 num_frag, len, tot_len, alm_offset, alm_offset_fframe, write_p, read_p;
+	unsigned long flags;
+	int sid, ii, tot_sz8;
+	static int chk_ptr;
+
+	/* fetch stream ID */
+	sid = tadma_get_strid(skb, ndev);
+
+	if (sid < 0) {
+		dev_kfree_skb_irq(skb);
+		return NETDEV_TX_OK;
+	}
+	num_frag = skb_shinfo(skb)->nr_frags;
+
+	spin_lock_irqsave(&lp->tadma_tx_lock, flags);
+	pm = tadma_ior(lp, XTADMA_PM_OFFSET + (sid * sizeof(pm_entry_t)));
+
+	read_p  = pm & XTADMA_PM_RD_MASK;
+	write_p = (pm & XTADMA_PM_WR_MASK) >> XTADMA_PM_WR_SHIFT;
+
+	if (!axienet_check_pm_space(sid, num_frag + 1, write_p, read_p,
+				    lp->num_tadma_buffers)) {
+		if (!chk_ptr) {
+			pr_err("%s NO SPACE rd: %x wd: %x\n", __func__, read_p,
+			       write_p);
+			chk_ptr = 1;
+		}
+		spin_unlock_irqrestore(&lp->tadma_tx_lock, flags);
+		return NETDEV_TX_BUSY;
+	}
+	if (((lp->tx_bd_head[sid] + (num_frag + 1)) % lp->num_tadma_buffers) ==
+	    lp->tx_bd_tail[sid]) {
+		if (!__netif_subqueue_stopped(ndev, queue_type))
+			netif_stop_subqueue(ndev, queue_type);
+		spin_unlock_irqrestore(&lp->tadma_tx_lock, flags);
+		return NETDEV_TX_BUSY;
+	}
+
+	/* get current alm offset */
+	alm_offset_fframe = tadma_stream_alm_offset(sid, write_p, ndev);
+
+	pr_debug("%d: num_frag: %d len: %d\n", sid, num_frag,
+		 skb_headlen(skb));
+	pr_debug("w:%d r:%d\n", write_p, read_p);
+
+	tot_len = skb_headlen(skb);
+	len = skb_headlen(skb);
+	phys_addr = dma_map_single(ndev->dev.parent, skb->data,
+				   len, DMA_TO_DEVICE);
+	if (unlikely(dma_mapping_error(ndev->dev.parent, phys_addr))) {
+		dev_err(&ndev->dev, "tadma map error\n");
+		spin_unlock_irqrestore(&lp->tadma_tx_lock, flags);
+		return NETDEV_TX_BUSY;
+	}
+
+	alm_fframe.addr = (u32)phys_addr;
+
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+	alm_fframe.cfg |= (u32)(phys_addr >> 32);
+#endif
+
+	lp->tx_bd[sid][lp->tx_bd_head[sid]].num_frag = num_frag + 1;
+	if (num_frag == 0) {
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].tx_skb = (phys_addr_t)skb;
+		alm_fframe.cfg |= XTADMA_ALM_SOP | XTADMA_ALM_EOP;
+	} else {
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].tx_skb = 0;
+		alm_fframe.cfg |= XTADMA_ALM_SOP;
+	}
+	alm_fframe.cfg &= ~XTADMA_ALM_FETCH_SZ_MASK;
+	alm_fframe.cfg |= ((len << XTADMA_ALM_FETCH_SZ_SHIFT) &
+			   XTADMA_ALM_FETCH_SZ_MASK);
+	lp->tx_bd[sid][lp->tx_bd_head[sid]].phys = phys_addr;
+	lp->tx_bd[sid][lp->tx_bd_head[sid]].len = len;
+	lp->tx_bd[sid][lp->tx_bd_head[sid]].tx_desc_mapping =
+							DESC_DMA_MAP_SINGLE;
+	lp->tx_bd_head[sid]++;
+	lp->tx_bd_head[sid] %= lp->num_tadma_buffers;
+
+	for (ii = 0; ii < num_frag; ii++) {
+		skb_frag_t *frag;
+
+		frag = &skb_shinfo(skb)->frags[ii];
+		len = skb_frag_size(frag);
+		tot_len += len;
+		phys_addr = skb_frag_dma_map(ndev->dev.parent, frag, 0,
+					     len, DMA_TO_DEVICE);
+		memset(&alm, 0, sizeof(struct alm_entry));
+		alm.addr = (u32)phys_addr;
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+		alm.cfg |= (u32)(phys_addr >> 32);
+#endif
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].tx_skb = 0;
+		if (ii == (num_frag - 1)) {
+			alm.cfg |= XTADMA_ALM_EOP;
+			lp->tx_bd[sid][lp->tx_bd_head[sid]].tx_skb =
+							(phys_addr_t)skb;
+		}
+		alm.cfg &= ~XTADMA_ALM_FETCH_SZ_MASK;
+		alm.cfg |= ((len << XTADMA_ALM_FETCH_SZ_SHIFT) &
+				XTADMA_ALM_FETCH_SZ_MASK);
+		alm.cfg |= XTADMA_ALM_UFF;
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].num_frag = 0;
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].phys = phys_addr;
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].len = len;
+		lp->tx_bd[sid][lp->tx_bd_head[sid]].tx_desc_mapping =
+							DESC_DMA_MAP_PAGE;
+		lp->tx_bd_head[sid]++;
+		lp->tx_bd_head[sid] %= lp->num_tadma_buffers;
+
+		/* increment write */
+		write_p = (write_p + 1) & (lp->num_tadma_buffers - 1);
+		/* get current alm offset */
+		alm_offset = tadma_stream_alm_offset(sid, write_p, ndev);
+
+		tadma_iow(lp, alm_offset, alm.addr);
+		tadma_iow(lp, alm_offset + 4, alm.cfg);
+	}
+	tot_sz8 = tot_len / 8 + 1;
+	alm_fframe.cfg &= ~XTADMA_ALM_TOT_PKT_SZ_BY8_MASK;
+	alm_fframe.cfg |= ((tot_sz8 << XTADMA_ALM_TOT_PKT_SZ_BY8_SHIFT) &
+			  XTADMA_ALM_TOT_PKT_SZ_BY8_MASK);
+	alm_fframe.cfg |= XTADMA_ALM_UFF;
+
+	tadma_iow(lp, alm_offset_fframe, alm_fframe.addr);
+	tadma_iow(lp, alm_offset_fframe + 4, alm_fframe.cfg);
+
+	/* increment write */
+	write_p = (write_p + 1) & (lp->num_tadma_buffers - 1);
+
+	pm &= ~XTADMA_PM_WR_MASK;
+	pm |= (write_p << XTADMA_PM_WR_SHIFT);
+
+	tadma_iow(lp, (XTADMA_PM_OFFSET + (sid * sizeof(pm_entry_t))), pm);
+	spin_unlock_irqrestore(&lp->tadma_tx_lock, flags);
+
+	return NETDEV_TX_OK;
+}
+
+int axienet_tadma_program(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct tadma_cb *cb = lp->t_cb;
+	struct tadma_stream_entry *entry;
+	struct hlist_head *bucket;
+	struct hlist_node *tmp;
+	u32 cr, hash = 0;
+	int ret = 0;
+
+	for (hash = 0; hash < lp->num_entries; hash++) {
+		bucket = &cb->stream_hash[hash];
+		hlist_for_each_entry_safe(entry, tmp, bucket, hash_link) {
+			tadma_sfm_program(ndev, entry->sfm,
+					  entry->tticks, entry->count);
+		}
+	}
+	/* flip memory first so access other sfm bank
+	 * cr = tadma_ior(lp, XTADMA_CR_OFFSET);
+	 * cr |= XTADMA_FLIP_FETCH_MEM;
+	 * tadma_iow(lp, XTADMA_CR_OFFSET, cr);
+	 */
+
+	/* re-enable interrupts */
+	tadma_iow(lp, XTADMA_INT_EN_OFFSET, XTADMA_FFI_INT_EN |
+		  XTADMA_IE_INT_EN);
+	/* enable schedule */
+	cr = XTADMA_CFG_DONE | XTADMA_SCHED_ENABLE;
+	tadma_iow(lp, XTADMA_CR_OFFSET, cr);
+
+	return ret;
+}
+
+int axienet_tadma_off(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+
+	tadma_iow(lp, XTADMA_INT_EN_OFFSET, XTADMA_FFI_INT_EN |
+		  XTADMA_IE_INT_EN);
+	tadma_sfm_program(ndev, STRID_BE, NSEC_PER_MSEC, 0);
+	tadma_iow(lp, XTADMA_CR_OFFSET, XTADMA_CFG_DONE);
+	get_sid = 0;
+	return 0;
+}
+
+int axienet_tadma_flush_stream(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct tadma_cb *cb = lp->t_cb;
+	struct tadma_stream_entry *entry;
+	struct hlist_head *bucket;
+	struct hlist_node *tmp;
+	u32 offset;
+	int hash;
+
+	/* set CFG_DONE to 0 */
+	tadma_iow(lp, XTADMA_CR_OFFSET, 0);
+
+	for (hash = 0; hash < lp->num_entries; hash++) {
+		offset = sfm_entry_offset(lp, hash);
+		tadma_iow(lp, offset, 0);
+		tadma_iow(lp, offset + 4, 0);
+
+		bucket = &cb->stream_hash[hash];
+		hlist_for_each_entry_safe(entry, tmp, bucket, hash_link) {
+			hlist_del(&entry->hash_link);
+			kfree(entry);
+		}
+	}
+
+	return 0;
+}
+
+int axienet_tadma_add_stream(struct net_device *ndev, void __user *useraddr)
+{
+	struct axienet_local *lp = netdev_priv(ndev);
+	struct tadma_stream stream;
+	struct tadma_cb *cb = lp->t_cb;
+	struct tadma_stream_entry *entry;
+	u32 idx, sid;
+	u16 vlan_tci;
+	u8 mac_vlan[8];
+	int st_pcp_val;
+
+	if (copy_from_user(&stream, useraddr, sizeof(struct tadma_stream)))
+		return -EFAULT;
+
+	if (stream.count > MAX_TRIG_COUNT)
+		return -EINVAL;
+
+	if (stream.start) {
+		get_sid = 0;
+		get_sfm = 0;
+	}
+
+	memcpy(mac_vlan, stream.dmac, 6);
+
+	for (st_pcp_val = 0; st_pcp_val < 8; st_pcp_val++) {
+		if (lp->st_pcp & (1 << st_pcp_val))
+			break;
+	}
+	vlan_tci = stream.vid & VLAN_VID_MASK;
+	vlan_tci |= (st_pcp_val << VLAN_PRIO_SHIFT) & VLAN_PRIO_MASK;
+	mac_vlan[6] = (vlan_tci >> 8) & 0x0f;
+	mac_vlan[7] = (vlan_tci & 0xff);
+
+	idx = tadma_macvlan_hash(mac_vlan);
+
+	entry = tadma_hash_lookup_stream(&cb->stream_hash[idx], mac_vlan);
+	if (entry && entry->count == stream.count &&
+	    entry->tticks == stream.trigger) {
+		return -EEXIST;	/*same entry*/
+	}
+
+	if (entry)
+		sid = entry->sid;	/*same sid diff entry*/
+	else
+		sid = get_sid++;
+
+	if (sid >= lp->num_streams) {
+		pr_err("More no. of streams %d\n", sid);
+		return -EINVAL;
+	}
+	if (get_sfm >= lp->num_entries) {
+		pr_err("\nMore no. of entries %d\n", get_sfm + 1);
+		return -EINVAL;
+	}
+
+	entry = kzalloc(sizeof(*entry), GFP_KERNEL);
+	if (!entry)
+		return -ENOMEM;
+
+	entry->tticks = stream.trigger;
+	entry->count = stream.count;
+	entry->sid = sid;
+	memcpy(entry->macvlan, mac_vlan, 8);
+	entry->sfm = get_sfm++;
+
+	pr_debug("%s sid: %d\n", __func__, sid);
+	hlist_add_head(&entry->hash_link, &cb->stream_hash[idx]);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_tadma.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_tadma.h
@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Definitions for TSN TADMA implementation
+ */
+#ifndef _XTADMA_TSN_H
+#define _XTADMA_TSN_H
+
+/* upper&lower stream fetch memory offsets */
+#define XTADMA_USFM_OFFSET	0x1000
+#define XTADMA_LSFM_OFFSET	0x2000
+
+/* pointers memory offset */
+#define XTADMA_PM_OFFSET	0x3000
+#define XTADMA_PM_RD_MASK	0xFF
+#define XTADMA_PM_WR_MASK	0xFF0000
+#define XTADMA_PM_WR_SHIFT	16
+
+/* Address length memory offset */
+#define XTADMA_ALM_OFFSET	0x40000
+
+#define XTADMA_CR_OFFSET		0x0
+#define XTADMA_TO_OFFSET		0x4
+#define XTADMA_FF_THRE_OFFSET		0x8
+#define XTADMA_STR_ID_OFFSET		0xC
+#define XTADMA_INT_EN_OFFSET		0x10
+#define XTADMA_INT_STA_OFFSET		0x14
+#define XTADMA_INT_CLR_OFFSET		0x18
+#define XTADMA_EDI_FFI_STAT_OFFSET	0x20
+#define XTADMA_NRDFI_FNDI_STAT_OFFSET	0x24
+#define XTADMA_BEI_STNSI_STAT_OFFSET	0x28
+#define XTADMA_BENSI_RESNSI_STAT_OFFSET	0x2C
+#define XTADMA_SEI_DEI_STAT_OFFSET	0x30
+#define XTADMA_IEI_STAT_OFFSET		0x34
+
+#define XTADMA_HALTED		BIT(5)
+#define XTADMA_SCHED_ENABLE	BIT(4)
+#define XTADMA_FLIP_FETCH_MEM	BIT(3)
+#define XTADMA_SKIP_DEL_ENTRY	BIT(2)
+#define XTADMA_SOFT_RST		BIT(1)
+#define XTADMA_CFG_DONE		BIT(0)
+
+#define XTADMA_OFFSET_TIME_SHIFT	16
+#define XTADMA_OFFSET_TIME_MASK		(0xFFFF)
+
+#define XTADMA_ENT_NUM_SEC_INTR_SHIFT	16
+#define XTADMA_ENT_NUM_SEC_INTR_MASK	(0xFF)
+#define XTADMA_FRAME_THRES_SHIFT	8
+#define XTADMA_FRAME_THRES_MASK		(0xFF)
+
+#define XTADMA_FIX_RES_QUEUE_ID_SHIFT	16
+#define XTADMA_FIX_RES_QUEUE_ID_MASK	(0xFF0000)
+#define XTADMA_FIX_BE_QUEUE_ID_SHIFT	0
+#define XTADMA_FIX_BE_QUEUE_ID_MASK	(0xFF)
+
+#define XTADMA_SEC_COMP_INT_EN		BIT(12)
+#define XTADMA_IE_INT_EN		BIT(11)
+#define XTADMA_SEI_INT_EN		BIT(10)
+#define XTADMA_DEI_INT_EN		BIT(9)
+#define XTADMA_BENSI_INT_EN		BIT(8)
+#define XTADMA_RESNSI_INT_EN		BIT(7)
+#define XTADMA_STNSI_INT_EN		BIT(6)
+#define XTADMA_BEI_INT_EN		BIT(5)
+#define XTADMA_NRDFI_INT_EN		BIT(4)
+#define XTADMA_FNDI_INT_EN		BIT(3)
+#define XTADMA_CDI_INT_EN		BIT(2)
+#define XTADMA_EDI_INT_EN		BIT(1)
+#define XTADMA_FFI_INT_EN		BIT(0)
+#define XTADMA_INT_EN_ALL_MASK		(0x1FFF)
+
+#define XTADMA_STR_FETCH_ENTRY_SIZE	64
+#define XTADMA_STR_TIME_TICKS_SHIFT	0
+#define XTADMA_STR_TIME_TICKS_MASK	(0x7FFFFFF)
+
+#define XTADMA_STR_ID_SHIFT		0
+#define XTADMA_STR_ID_MASK		0xFF
+#define XTADMA_STR_NUM_FRM_SHIFT	16
+#define XTADMA_STR_NUM_FRM_MASK		0x30000
+#define XTADMA_STR_QUE_TYPE_SHIFT	20
+#define XTADMA_STR_QUE_TYPE_MASK	0x300000
+#define XTADMA_STR_CONT_FETCH_EN	BIT(22)
+#define XTADMA_STR_ENTRY_VALID		BIT(31)
+
+#define XTADMA_ALM_ADDR_MSB_SHIFT	0
+#define XTADMA_ALM_ADDR_MSB_MASK	0xFF
+#define XTADMA_ALM_TOT_PKT_SZ_BY8_SHIFT	8
+#define XTADMA_ALM_TOT_PKT_SZ_BY8_MASK	0xFF00
+#define XTADMA_ALM_FETCH_SZ_SHIFT	16
+#define XTADMA_ALM_FETCH_SZ_MASK	0xFFF0000
+#define XTADMA_ALM_UFF			BIT(28)
+#define XTADMA_ALM_SOP			BIT(30)
+#define XTADMA_ALM_EOP			BIT(31)
+
+#define SFM_UPPER 0
+#define SFM_LOWER 1
+
+
+enum qtype {
+	qt_st = 0,
+	qt_res,
+	qt_be,
+	qt_resbe
+};
+
+/* address/length memory entry */
+struct alm_entry {
+	u32 addr;
+	u32 cfg;
+};
+
+/* stream fetch entry */
+struct sfm_entry {
+	u32 tticks;
+	u32 cfg;
+};
+
+struct tadma_cb {
+	struct hlist_head *stream_hash;
+	int streams;
+	u32 be_trigger;
+};
+
+static inline u32 tadma_ior(struct axienet_local *lp, off_t offset)
+{
+	return ioread32(lp->tadma_regs + offset);
+}
+
+static inline void tadma_iow(struct axienet_local *lp, off_t offset,
+			     u32 value)
+{
+	iowrite32(value, (lp->tadma_regs + offset));
+}
+#endif /* _XTADMA_TSN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xilinx-tsn/xilinx_tsn_timer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xilinx-tsn/xilinx_tsn_timer.h
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Xilinx FPGA Xilinx TSN timer module header.
+ *
+ * Copyright (c) 2017 Xilinx Pvt., Ltd
+ *
+ * Author: Syed S <syeds@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XILINX_TSN_H_
+#define _XILINX_TSN_H_
+
+#include <linux/platform_device.h>
+
+#define XAE_RTC_OFFSET			0x12800
+/* RTC Nanoseconds Field Offset Register */
+#define XTIMER1588_RTC_OFFSET_NS	0x00000
+/* RTC Seconds Field Offset Register - Low */
+#define XTIMER1588_RTC_OFFSET_SEC_L	0x00008
+/* RTC Seconds Field Offset Register - High */
+#define XTIMER1588_RTC_OFFSET_SEC_H	0x0000C
+/* RTC Increment */
+#define XTIMER1588_RTC_INCREMENT	0x00010
+/* Current TOD Nanoseconds - RO */
+#define XTIMER1588_CURRENT_RTC_NS	0x00014
+/* Current TOD Seconds -Low RO  */
+#define XTIMER1588_CURRENT_RTC_SEC_L	0x00018
+/* Current TOD Seconds -High RO */
+#define XTIMER1588_CURRENT_RTC_SEC_H	0x0001C
+#define XTIMER1588_SYNTONIZED_NS	0x0002C
+#define XTIMER1588_SYNTONIZED_SEC_L	0x00030
+#define XTIMER1588_SYNTONIZED_SEC_H	0x00034
+/* Write to Bit 0 to clear the interrupt */
+#define XTIMER1588_INTERRUPT		0x00020
+/* 8kHz Pulse Offset Register */
+#define XTIMER1588_8KPULSE		0x00024
+/* Correction Field - Low */
+#define XTIMER1588_CF_L			0x0002C
+/* Correction Field - Low */
+#define XTIMER1588_CF_H			0x00030
+
+#define XTIMER1588_RTC_MASK  ((1 << 26) - 1)
+#define XTIMER1588_INT_SHIFT 0
+#define NANOSECOND_BITS 20
+#define NANOSECOND_MASK ((1 << NANOSECOND_BITS) - 1)
+#define SECOND_MASK ((1 << (32 - NANOSECOND_BITS)) - 1)
+#define XTIMER1588_RTC_INCREMENT_SHIFT 20
+#define PULSESIN1PPS 128
+
+/* Read/Write access to the registers */
+#ifndef out_be32
+#if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP)
+#define in_be32(offset)		__raw_readl(offset)
+#define out_be32(offset, val)	__raw_writel(val, offset)
+#endif
+#endif
+
+/* The tsn ptp module will set this variable */
+extern int axienet_phc_index;
+
+void *axienet_ptp_timer_probe(void __iomem *base,
+			      struct platform_device *pdev);
+int axienet_ptp_timer_remove(void *priv);
+int axienet_get_phc_index(void *priv);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnx_tsmux/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnx_tsmux/Kconfig
@@ -0,0 +1,11 @@
+config XLNX_TSMUX
+	tristate "Xilinx MPEG2 Transport Stream Muxer"
+	select DMA_SHARED_BUFFER
+	help
+	  This driver is developed for mpeg2 transport stream muxer,
+	  designed to allow passage of multimedia streams from the source
+	  kernel sub-system, prepares mpeg2 transport stream and forward
+	  to the sink kernel subsystem.
+
+	  To compile this driver as a module, choose M here.
+	  If unsure, choose N.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnx_tsmux/MAINTAINERS
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnx_tsmux/MAINTAINERS
@@ -0,0 +1,4 @@
+XILINX MPG2TSMUX DRIVER
+M:	Venkateshwar Rao <venkateshwar.rao.gannavarapu@xilinx.com>
+S:	Maintained
+F:	drivers/staging/xlnx_tsmux
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnx_tsmux/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnx_tsmux/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_XLNX_TSMUX) += xlnx_mpg2tsmux.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnx_tsmux/dt-binding.txt
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnx_tsmux/dt-binding.txt
@@ -0,0 +1,28 @@
+The Xilinx mpegtsmux IP reads the elementary streams from memory and
+writes the MPEG2 TS(transport stream) to memory.
+
+The mpeg2 ts muxer follows the dma descriptor based approach. Each DMA
+descriptor contains information about each of the elementary stream
+buffer properties and buffer address. It reads the descriptors one after
+the other and generates the TS packets with the information in the
+descriptor. The IP writes the generated TS packets at the output buffer
+address.
+
+Required properties:
+
+- compatible: must be "xlnx,tsmux-1.0"
+- interrupts: interrupt number
+- interrupts-parent: phandle for interrupt controller
+- reg: base address and size of the IP core
+- clock-names: must contain "ap_clk"
+- clocks: phandle to AXI Lite
+
+Example:
+	ts2mux: ts2mux@0xa0200000 {
+		compatible = "xlnx,tsmux-1.0";
+		interrupt-parent = <&gic>;
+		interrupts = <0 90 4>;
+		reg = <0x0 0xa0200000 0x0 0x30000>;
+		clock-names = "ap_clk";
+		clocks = <&misc_clk_0>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnx_tsmux/xlnx_mpg2tsmux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnx_tsmux/xlnx_mpg2tsmux.c
@@ -0,0 +1,1568 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx TS mux driver
+ *
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author: Venkateshwar Rao G <venkateshwar.rao.gannavarapu@xilinx.com>
+ */
+#include <linux/bitops.h>
+#include <linux/cdev.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dmapool.h>
+#include <linux/dma-buf.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/poll.h>
+#include <uapi/linux/xlnx_mpg2tsmux_interface.h>
+
+#define DRIVER_NAME "mpegtsmux-1.0"
+#define DRIVER_CLASS "mpg2mux_ts_cls"
+#define DRIVER_MAX_DEV (10)
+
+/* Register offsets and bit masks */
+#define XTSMUX_RST_CTRL			0x00
+#define XTSMUX_GLBL_IER			0x04
+#define XTSMUX_IER_STAT			0x08
+#define XTSMUX_ISR_STAT			0x0c
+#define XTSMUX_ERR_STAT			0x10
+#define XTSMUX_LAST_NODE_PROCESSED	0x14
+#define XTSMUX_MUXCONTEXT_ADDR		0x20
+#define XTSMUX_STREAMCONTEXT_ADDR	0x30
+#define XTSMUX_NUM_STREAM_IDTBL		0x48
+#define XTSMUX_NUM_DESC			0x70
+#define XTSMUX_STREAM_IDTBL_ADDR	0x78
+#define XTSMUX_CONTEXT_DATA_SIZE	64
+
+#define XTSMUX_RST_CTRL_START_MASK	BIT(0)
+#define XTSMUX_GLBL_IER_ENABLE_MASK	BIT(0)
+#define XTSMUX_IER_ENABLE_MASK		BIT(0)
+
+/* Number of input/output streams supported */
+#define XTSMUX_MAXIN_STRM		112
+#define XTSMUX_MAXIN_PLSTRM		16
+#define XTSMUX_MAXIN_TLSTRM	(XTSMUX_MAXIN_STRM + XTSMUX_MAXIN_PLSTRM)
+#define XTSMUX_MAXOUT_STRM		112
+#define XTSMUX_MAXOUT_PLSTRM		16
+#define XTSMUX_MAXOUT_TLSTRM	(XTSMUX_MAXOUT_STRM + XTSMUX_MAXOUT_PLSTRM)
+#define XTSMUX_POOL_SIZE		128
+/* Initial version is tested with 256 align only */
+#define XTSMUX_POOL_ALIGN		256
+#define XTSMUX_STRMBL_FREE		0
+#define XTSMUX_STRMBL_BUSY		1
+
+/**
+ * struct stream_context - struct to enqueue a stream context descriptor
+ * @command: stream context type
+ * @is_pcr_stream: flag for pcr(programmable clock recovery) stream
+ * @stream_id: stream identification number
+ * @extended_stream_id: extended stream id
+ * @reserved1: reserved for hardware alignment
+ * @pid: packet id number
+ * @dmabuf_id: 0 for buf allocated by driver, nonzero for external buf
+ * @size_data_in: size in bytes of input buffer
+ * @pts: presentation time stamp
+ * @dts: display time stamp
+ * @in_buf_pointer: physical address of src buf address
+ * @reserved2: reserved for hardware alignment
+ * @insert_pcr: inserting pcr in stream context
+ * @reserved3: reserved for hardware alignment
+ * @pcr_extension: pcr extension number
+ * @pcr_base: pcr base number
+ */
+struct stream_context {
+	enum ts_mux_command command;
+	bool is_pcr_stream;
+	u8 stream_id;
+	u8 extended_stream_id;
+	u8 reserved1;
+	u16 pid;
+	u16 dmabuf_id;
+	u32 size_data_in;
+	u64 pts;
+	u64 dts;
+	u64 in_buf_pointer;
+	u32 reserved2;
+	bool insert_pcr;
+	bool reserved3;
+	u16 pcr_extension;
+	u64 pcr_base;
+};
+
+/**
+ * enum node_status_info - status of stream context
+ * @NOT_FILLED: node not filled
+ * @UPDATED_BY_DRIVER: updated by driver
+ * @READ_BY_IP: read by IP
+ * @USED_BY_IP: used by IP
+ * @NODE_INVALID: invalid node
+ */
+enum node_status_info {
+	NOT_FILLED = 0,
+	UPDATED_BY_DRIVER,
+	READ_BY_IP,
+	USED_BY_IP,
+	NODE_INVALID
+};
+
+/**
+ * enum stream_errors - stream context error type
+ * @NO_ERROR: no error
+ * @PARTIAL_FRAME_WRITTEN: partial frame written
+ * @DESCRIPTOR_NOT_READABLE: descriptor not readable
+ */
+enum stream_errors {
+	NO_ERROR = 0,
+	PARTIAL_FRAME_WRITTEN,
+	DESCRIPTOR_NOT_READABLE
+};
+
+/**
+ * struct strm_node - struct to describe stream node in linked list
+ * @node_number: node number to handle streams
+ * @node_status: status of stream node
+ * @element: stream context info
+ * @error_code: error codes
+ * @reserved1: reserved bits for hardware align
+ * @tail_pointer: physical address of next stream node in linked list
+ * @strm_phy_addr: physical address of stream context
+ * @node: struct of linked list head
+ * @reserved2: reserved for hardware align
+ */
+struct stream_context_node {
+	u32 node_number;
+	enum node_status_info node_status;
+	struct stream_context element;
+	enum stream_errors error_code;
+	u32 reserved1;
+	u64 tail_pointer;
+	u64 strm_phy_addr;
+	struct list_head node;
+	u64 reserved2;
+};
+
+/**
+ * struct strm_info - struct to describe streamid node in streamid table
+ * @pid: identification number of stream
+ * @continuity_counter: counter to maintain packet count for a stream
+ * @usageflag: flag to know free or under use for allocating streamid node
+ * @strmtbl_update: struct to know enqueue or dequeue streamid in table
+ */
+struct stream_info {
+	u16 pid;
+	u8 continuity_counter;
+	bool usageflag;
+	enum strmtbl_cnxt strmtbl_update;
+};
+
+/* Enum for error handling of mux context */
+enum mux_op_errs {
+	MUXER_NO_ERROR = 0,
+	ERROR_OUTPUT_BUFFER_IS_NOT_ACCESIBLE,
+	ERROR_PARTIAL_PACKET_WRITTEN
+};
+
+/**
+ * struct muxer_context - struct to describe mux node in linked list
+ * @node_status: status of mux node
+ * @reserved: reserved for hardware align
+ * @dst_buf_start_addr: physical address of dst buf
+ * @dst_buf_size: size of the output buffer
+ * @dst_buf_written: size of data written in dst buf
+ * @num_of_pkts_written: number of packets in dst buf
+ * @error_code: error status of mux node updated by IP
+ * @mux_phy_addr: physical address of muxer
+ * @node: struct of linked list head
+ */
+struct muxer_context {
+	enum node_status_info node_status;
+	u32 reserved;
+	u64 dst_buf_start_addr;
+	u32 dst_buf_size;
+	u32 dst_buf_written;
+	u32 num_of_pkts_written;
+	enum mux_op_errs error_code;
+	u64 mux_phy_addr;
+	struct list_head node;
+};
+
+/**
+ * struct xlnx_tsmux_dmabufintl - dma buf internal info
+ * @dbuf: reference to a buffer's dmabuf struct
+ * @attach: attachment to the buffer's dmabuf
+ * @sgt: scatterlist info for the buffer's dmabuf
+ * @dmabuf_addr: buffer physical address
+ * @dmabuf_fd: dma buffer fd
+ * @buf_id: dma buffer reference id
+ */
+struct xlnx_tsmux_dmabufintl {
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	dma_addr_t dmabuf_addr;
+	s32 dmabuf_fd;
+	u16 buf_id;
+};
+
+/**
+ * struct xlnx_tsmux - xilinx mpeg2 TS muxer device
+ * @dev: pointer to struct device instance used by the driver
+ * @iomem: base address of the HW/IP
+ * @chdev: char device handle
+ * @user_count: count of users who have opened the device
+ * @lock: spinlock to protect driver data structures
+ * @waitq: wait queue used by the driver
+ * @irq: irq number
+ * @id: device instance ID
+ * @num_inbuf: number of input buffers allocated uisng DMA
+ * @num_outbuf: number of output buffers allocated uisng DMA
+ * @srcbuf_size: size of each source buffer
+ * @dstbuf_size: size of each destination buffer
+ * @strm_node: list containing descriptors of stream context
+ * @mux_node: list containing descriptors of mux context
+ * @stcxt_node_cnt: stream number used for maintaing list
+ * @num_strmnodes: number of stream nodes in the streamid table
+ * @intn_stream_count: internal count of streams added to stream context
+ * @outbuf_idx: index number to maintain output buffers
+ * @srcbuf_addrs: physical address of source buffer
+ * @dstbuf_addrs: physical address of destination buffer
+ * @src_kaddrs: kernel VA for source buffer allocated by the driver
+ * @dst_kaddrs: kernel VA for destination buffer allocated by the driver
+ * @strm_ctx_pool: dma pool to allocate stream context buffers
+ * @mux_ctx_pool: dma pool to allocate mux context buffers
+ * @strmtbl_addrs: physical address of streamid table
+ * @strmtbl_kaddrs: kernel VA for streamid table
+ * @intn_strmtbl_addrs: physical address of streamid table for internal
+ * @intn_strmtbl_kaddrs: kernel VA for streamid table for internal
+ * @ap_clk: interface clock
+ * @src_dmabufintl: array of src DMA buf allocated by user
+ * @dst_dmabufintl: array of src DMA buf allocated by user
+ * @outbuf_written: size in bytes written in output buffer
+ * @stream_count: stream count
+ */
+struct xlnx_tsmux {
+	struct device *dev;
+	void __iomem *iomem;
+	struct cdev chdev;
+	atomic_t user_count;
+	/* lock is used to protect access to sync_err and wdg_err */
+	spinlock_t lock;
+	wait_queue_head_t waitq;
+	s32 irq;
+	s32 id;
+	u32 num_inbuf;
+	u32 num_outbuf;
+	size_t srcbuf_size;
+	size_t dstbuf_size;
+	struct list_head strm_node;
+	struct list_head mux_node;
+	u32 stcxt_node_cnt;
+	u32 num_strmnodes;
+	atomic_t intn_stream_count;
+	atomic_t outbuf_idx;
+	dma_addr_t srcbuf_addrs[XTSMUX_MAXIN_TLSTRM];
+	dma_addr_t dstbuf_addrs[XTSMUX_MAXOUT_TLSTRM];
+	void *src_kaddrs[XTSMUX_MAXIN_TLSTRM];
+	void *dst_kaddrs[XTSMUX_MAXOUT_TLSTRM];
+	struct dma_pool *strm_ctx_pool;
+	struct dma_pool *mux_ctx_pool;
+	dma_addr_t strmtbl_addrs;
+	void *strmtbl_kaddrs;
+	dma_addr_t intn_strmtbl_addrs;
+	void *intn_strmtbl_kaddrs;
+	struct clk *ap_clk;
+	struct xlnx_tsmux_dmabufintl src_dmabufintl[XTSMUX_MAXIN_STRM];
+	struct xlnx_tsmux_dmabufintl dst_dmabufintl[XTSMUX_MAXOUT_STRM];
+	s32 outbuf_written;
+	atomic_t stream_count;
+};
+
+static inline u32 xlnx_tsmux_read(const struct xlnx_tsmux *mpgmuxts,
+				  const u32 reg)
+{
+	return ioread32(mpgmuxts->iomem + reg);
+}
+
+static inline void xlnx_tsmux_write(const struct xlnx_tsmux *mpgmuxts,
+				    const u32 reg, const u32 val)
+{
+	iowrite32(val, (void __iomem *)(mpgmuxts->iomem + reg));
+}
+
+/* TODO: Optimize using iowrite64 call */
+static inline void xlnx_tsmux_write64(const struct xlnx_tsmux *mpgmuxts,
+				      const u32 reg, const u64 val)
+{
+	iowrite32(lower_32_bits(val), (void __iomem *)(mpgmuxts->iomem + reg));
+	iowrite32(upper_32_bits(val), (void __iomem *)(mpgmuxts->iomem +
+						       reg + 4));
+}
+
+static int xlnx_tsmux_start_muxer(struct xlnx_tsmux *mpgmuxts)
+{
+	struct stream_context_node *new_strm_node;
+	struct muxer_context *new_mux_node;
+
+	new_mux_node = list_first_entry_or_null(&mpgmuxts->mux_node,
+						struct muxer_context, node);
+	if (!new_mux_node)
+		return -ENXIO;
+
+	xlnx_tsmux_write64(mpgmuxts, XTSMUX_MUXCONTEXT_ADDR,
+			   new_mux_node->mux_phy_addr);
+
+	new_strm_node = list_first_entry_or_null(&mpgmuxts->strm_node,
+						 struct stream_context_node,
+						 node);
+	if (!new_strm_node)
+		return -ENXIO;
+
+	xlnx_tsmux_write64(mpgmuxts, XTSMUX_STREAMCONTEXT_ADDR,
+			   new_strm_node->strm_phy_addr);
+
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_NUM_DESC,
+			 atomic_read(&mpgmuxts->intn_stream_count));
+
+	xlnx_tsmux_write64(mpgmuxts, XTSMUX_STREAM_IDTBL_ADDR,
+			   (u64)mpgmuxts->intn_strmtbl_addrs);
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_NUM_STREAM_IDTBL, 1);
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_GLBL_IER,
+			 XTSMUX_GLBL_IER_ENABLE_MASK);
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_IER_STAT,
+			 XTSMUX_IER_ENABLE_MASK);
+
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_RST_CTRL,
+			 XTSMUX_RST_CTRL_START_MASK);
+
+	return 0;
+}
+
+static void xlnx_tsmux_stop_muxer(const struct xlnx_tsmux *mpgmuxts)
+{
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_GLBL_IER, 0);
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_IER_STAT, 0);
+	xlnx_tsmux_write(mpgmuxts, XTSMUX_RST_CTRL, 0);
+}
+
+static enum xlnx_tsmux_status xlnx_tsmux_get_status(const struct
+						    xlnx_tsmux * mpgmuxts)
+{
+	u32 status;
+
+	status = xlnx_tsmux_read(mpgmuxts, XTSMUX_RST_CTRL);
+
+	if (!status)
+		return MPG2MUX_ERROR;
+
+	if (status & XTSMUX_RST_CTRL_START_MASK)
+		return MPG2MUX_BUSY;
+
+	return MPG2MUX_READY;
+}
+
+static struct class *xlnx_tsmux_class;
+static dev_t xlnx_tsmux_devt;
+static atomic_t xlnx_tsmux_ndevs = ATOMIC_INIT(0);
+
+static int xlnx_tsmux_open(struct inode *pin, struct file *fptr)
+{
+	struct xlnx_tsmux *mpgtsmux;
+
+	mpgtsmux = container_of(pin->i_cdev, struct xlnx_tsmux, chdev);
+
+	fptr->private_data = mpgtsmux;
+	atomic_inc(&mpgtsmux->user_count);
+	atomic_set(&mpgtsmux->outbuf_idx, 0);
+	mpgtsmux->stcxt_node_cnt = 0;
+
+	return 0;
+}
+
+static int xlnx_tsmux_release(struct inode *pin, struct file *fptr)
+{
+	struct xlnx_tsmux *mpgtsmux = (struct xlnx_tsmux *)fptr->private_data;
+
+	if (!mpgtsmux)
+		return -EIO;
+
+	return 0;
+}
+
+/* TODO: Optimize buf alloc, dealloc API's to accommodate src, dst, strmtbl */
+static int xlnx_tsmux_ioctl_srcbuf_dealloc(struct xlnx_tsmux *mpgmuxts)
+{
+	unsigned int i;
+
+	for (i = 0; i < mpgmuxts->num_inbuf; i++) {
+		if (!mpgmuxts->src_kaddrs[i] || !mpgmuxts->srcbuf_addrs[i])
+			break;
+		dma_free_coherent(mpgmuxts->dev, mpgmuxts->srcbuf_size,
+				  mpgmuxts->src_kaddrs[i],
+				  mpgmuxts->srcbuf_addrs[i]);
+		mpgmuxts->src_kaddrs[i] = NULL;
+	}
+
+	return 0;
+}
+
+static int xlnx_tsmux_ioctl_srcbuf_alloc(struct xlnx_tsmux *mpgmuxts,
+					 void __user *arg)
+{
+	int ret;
+	unsigned int i;
+	struct strc_bufs_info buf_data;
+
+	ret = copy_from_user(&buf_data, arg, sizeof(struct strc_bufs_info));
+	if (ret < 0) {
+		dev_dbg(mpgmuxts->dev, "Failed to read input buffer info\n");
+		return ret;
+	}
+
+	if (buf_data.num_buf > XTSMUX_MAXIN_PLSTRM) {
+		dev_dbg(mpgmuxts->dev, "Excessive input payload. supported %d",
+			XTSMUX_MAXIN_PLSTRM);
+		return -EINVAL;
+	}
+
+	mpgmuxts->num_inbuf = buf_data.num_buf;
+	mpgmuxts->srcbuf_size = buf_data.buf_size;
+	/* buf_size & num_buf boundary conditions are handled in application
+	 * and initial version of driver tested with 32-bit addressing only
+	 */
+	for (i = 0; i < mpgmuxts->num_inbuf; i++) {
+		mpgmuxts->src_kaddrs[i] =
+			dma_alloc_coherent(mpgmuxts->dev,
+					   mpgmuxts->srcbuf_size,
+					   &mpgmuxts->srcbuf_addrs[i],
+					   GFP_KERNEL | GFP_DMA32);
+		if (!mpgmuxts->src_kaddrs[i]) {
+			dev_dbg(mpgmuxts->dev, "dma alloc fail %d buffer", i);
+			goto exit_free;
+		}
+	}
+
+	return 0;
+
+exit_free:
+	xlnx_tsmux_ioctl_srcbuf_dealloc(mpgmuxts);
+
+	return -ENOMEM;
+}
+
+static int xlnx_tsmux_ioctl_dstbuf_dealloc(struct xlnx_tsmux *mpgmuxts)
+{
+	unsigned int i;
+
+	for (i = 0; i < mpgmuxts->num_outbuf; i++) {
+		if (!mpgmuxts->dst_kaddrs[i] || !mpgmuxts->dstbuf_addrs[i])
+			break;
+		dma_free_coherent(mpgmuxts->dev, mpgmuxts->dstbuf_size,
+				  mpgmuxts->dst_kaddrs[i],
+				  mpgmuxts->dstbuf_addrs[i]);
+		mpgmuxts->dst_kaddrs[i] = NULL;
+	}
+
+	return 0;
+}
+
+static int xlnx_tsmux_ioctl_dstbuf_alloc(struct xlnx_tsmux *mpgmuxts,
+					 void __user *arg)
+{
+	int ret;
+	unsigned int i;
+	struct strc_bufs_info buf_data;
+
+	ret = copy_from_user(&buf_data, arg, sizeof(struct strc_bufs_info));
+	if (ret < 0) {
+		dev_dbg(mpgmuxts->dev, "%s: Failed to read output buffer info",
+			__func__);
+		return ret;
+	}
+
+	if (buf_data.num_buf > XTSMUX_MAXOUT_PLSTRM) {
+		dev_dbg(mpgmuxts->dev, "Excessive output payload supported %d",
+			XTSMUX_MAXOUT_PLSTRM);
+		return -EINVAL;
+	}
+
+	mpgmuxts->num_outbuf = buf_data.num_buf;
+	mpgmuxts->dstbuf_size = buf_data.buf_size;
+	/* buf_size & num_buf boundary conditions are handled in application*/
+	for (i = 0; i < mpgmuxts->num_outbuf; i++) {
+		mpgmuxts->dst_kaddrs[i] =
+			dma_alloc_coherent(mpgmuxts->dev,
+					   mpgmuxts->dstbuf_size,
+					   &mpgmuxts->dstbuf_addrs[i],
+					   GFP_KERNEL | GFP_DMA32);
+		if (!mpgmuxts->dst_kaddrs[i]) {
+			dev_dbg(mpgmuxts->dev, "dmamem alloc fail for %d", i);
+			goto exit_free;
+		}
+	}
+
+	return 0;
+
+exit_free:
+	xlnx_tsmux_ioctl_dstbuf_dealloc(mpgmuxts);
+
+	return -ENOMEM;
+}
+
+static int xlnx_tsmux_ioctl_strmtbl_dealloc(struct xlnx_tsmux *mpgmuxts)
+{
+	u32 buf_size;
+
+	buf_size = sizeof(struct stream_info) * mpgmuxts->num_strmnodes;
+	if (!mpgmuxts->strmtbl_kaddrs || !mpgmuxts->strmtbl_addrs)
+		return 0;
+
+	dma_free_coherent(mpgmuxts->dev, buf_size, mpgmuxts->strmtbl_kaddrs,
+			  mpgmuxts->strmtbl_addrs);
+	mpgmuxts->strmtbl_kaddrs = NULL;
+
+	if (!mpgmuxts->intn_strmtbl_kaddrs || !mpgmuxts->intn_strmtbl_addrs)
+		return 0;
+	dma_free_coherent(mpgmuxts->dev, buf_size,
+			  mpgmuxts->intn_strmtbl_kaddrs,
+			  mpgmuxts->intn_strmtbl_addrs);
+	mpgmuxts->intn_strmtbl_kaddrs = NULL;
+
+	return 0;
+}
+
+static int xlnx_tsmux_ioctl_strmtbl_alloc(struct xlnx_tsmux *mpgmuxts,
+					  void __user *arg)
+{
+	int ret, buf_size;
+	u16 num_nodes;
+
+	ret = copy_from_user(&num_nodes, arg, sizeof(u16));
+	if (ret < 0) {
+		dev_dbg(mpgmuxts->dev, "Failed to read streamid table info");
+		return ret;
+	}
+	mpgmuxts->num_strmnodes = num_nodes;
+	buf_size = sizeof(struct stream_info) * mpgmuxts->num_strmnodes;
+
+	mpgmuxts->strmtbl_kaddrs =
+		dma_alloc_coherent(mpgmuxts->dev,
+				   buf_size, &mpgmuxts->strmtbl_addrs,
+				   GFP_KERNEL | GFP_DMA32);
+	if (!mpgmuxts->strmtbl_kaddrs) {
+		dev_dbg(mpgmuxts->dev, "dmamem alloc fail for strm table");
+		return -ENOMEM;
+	}
+
+	/* Allocating memory for internal streamid table */
+	mpgmuxts->intn_strmtbl_kaddrs =
+		dma_alloc_coherent(mpgmuxts->dev,
+				   buf_size, &mpgmuxts->intn_strmtbl_addrs,
+				   GFP_KERNEL | GFP_DMA32);
+
+	if (!mpgmuxts->intn_strmtbl_kaddrs) {
+		dev_dbg(mpgmuxts->dev, "dmamem alloc fail for intr strm table");
+		goto exist_free;
+	}
+
+	return 0;
+exist_free:
+	xlnx_tsmux_ioctl_strmtbl_dealloc(mpgmuxts);
+
+	return -ENOMEM;
+}
+
+/**
+ * xlnx_tsmux_update_intstrm_tbl - updates stream id table
+ * @mpgmuxts: pointer to the device structure
+ *
+ * This function updates the stream id table
+ *
+ * Return: 0 on success and error value on failure.
+ *
+ */
+static int xlnx_tsmux_update_intstrm_tbl(struct xlnx_tsmux *mpgmuxts)
+{
+	struct stream_info *cptr, *intn_cptr;
+	int i, j;
+
+	cptr = (struct stream_info *)mpgmuxts->strmtbl_kaddrs;
+
+	if (!cptr->usageflag)
+		return 0;
+
+	for (i = 0; i < mpgmuxts->num_strmnodes && cptr->usageflag;
+	     i++, cptr++) {
+		intn_cptr = (struct stream_info *)mpgmuxts->intn_strmtbl_kaddrs;
+		/* Adding to table */
+		if (cptr->strmtbl_update == ADD_TO_TBL) {
+			for (j = 0; j < mpgmuxts->num_strmnodes;
+			     j++, intn_cptr++) {
+				if (!intn_cptr->usageflag) {
+					intn_cptr->pid = cptr->pid;
+					intn_cptr->continuity_counter = 0;
+					intn_cptr->usageflag = 1;
+					cptr->usageflag = 0;
+					break;
+				}
+			}
+			if (j == mpgmuxts->num_strmnodes)
+				return -EIO;
+		} else if (cptr->strmtbl_update == DEL_FR_TBL) {
+			/* deleting from table */
+			for (j = 0; j < mpgmuxts->num_strmnodes; j++,
+			     intn_cptr++) {
+				if (intn_cptr->usageflag) {
+					if (intn_cptr->pid == cptr->pid) {
+						intn_cptr->pid = 0;
+						intn_cptr->continuity_counter = 0;
+						intn_cptr->usageflag = 0;
+						cptr->usageflag = 0;
+						break;
+					}
+				}
+			}
+			if (j == mpgmuxts->num_strmnodes)
+				return -EIO;
+		} else {
+			return -EIO;
+		}
+	}
+
+	return 0;
+}
+
+static int xlnx_tsmux_update_strminfo_table(struct xlnx_tsmux *mpgmuxts,
+					    struct strc_strminfo new_strm_info)
+{
+	u32 i = 0;
+	struct stream_info *cptr;
+
+	cptr = (struct stream_info *)mpgmuxts->strmtbl_kaddrs;
+
+	/* Finding free memory block and writing input data into the block*/
+	for (i = 0; i < mpgmuxts->num_strmnodes; i++, cptr++) {
+		if (!cptr->usageflag) {
+			cptr->pid = new_strm_info.pid;
+			cptr->continuity_counter = 0;
+			cptr->usageflag = XTSMUX_STRMBL_BUSY;
+			cptr->strmtbl_update = new_strm_info.strmtbl_ctxt;
+			break;
+		}
+	}
+	if (i == mpgmuxts->num_strmnodes)
+		return -EIO;
+
+	return 0;
+}
+
+static int xlnx_tsmux_ioctl_update_strmtbl(struct xlnx_tsmux *mpgmuxts,
+					   void __user *arg)
+{
+	int ret;
+	struct strc_strminfo new_strm_info;
+
+	ret = copy_from_user(&new_strm_info, arg, sizeof(struct strc_strminfo));
+	if (ret < 0) {
+		dev_dbg(mpgmuxts->dev, "Reading strmInfo failed");
+		return ret;
+	}
+
+	return xlnx_tsmux_update_strminfo_table(mpgmuxts, new_strm_info);
+}
+
+static int xlnx_tsmux_enqueue_stream_context(struct xlnx_tsmux *mpgmuxts,
+					     struct
+					     stream_context_in * stream_data)
+{
+	struct stream_context_node *new_strm_node, *prev_strm_node;
+	void *kaddr_strm_node;
+	dma_addr_t strm_phy_addr;
+	unsigned long flags;
+	u32 i;
+
+	kaddr_strm_node = dma_pool_alloc(mpgmuxts->strm_ctx_pool,
+					 GFP_KERNEL | GFP_DMA32,
+					 &strm_phy_addr);
+
+	new_strm_node = (struct stream_context_node *)kaddr_strm_node;
+	if (!new_strm_node)
+		return -ENOMEM;
+
+	/* update the stream context node */
+	wmb();
+	new_strm_node->element.command = stream_data->command;
+	new_strm_node->element.is_pcr_stream = stream_data->is_pcr_stream;
+	new_strm_node->element.stream_id = stream_data->stream_id;
+	new_strm_node->element.extended_stream_id =
+				stream_data->extended_stream_id;
+	new_strm_node->element.pid = stream_data->pid;
+	new_strm_node->element.size_data_in = stream_data->size_data_in;
+	new_strm_node->element.pts = stream_data->pts;
+	new_strm_node->element.dts = stream_data->dts;
+	new_strm_node->element.insert_pcr = stream_data->insert_pcr;
+	new_strm_node->element.pcr_base = stream_data->pcr_base;
+	new_strm_node->element.pcr_extension = stream_data->pcr_extension;
+
+	/* Check for external dma buffer */
+	if (!stream_data->is_dmabuf) {
+		new_strm_node->element.in_buf_pointer =
+			mpgmuxts->srcbuf_addrs[stream_data->srcbuf_id];
+		new_strm_node->element.dmabuf_id = 0;
+	} else {
+		for (i = 0; i < XTSMUX_MAXIN_STRM; i++) {
+			/* Serching dma buf info based on srcbuf_id */
+			if (stream_data->srcbuf_id ==
+					mpgmuxts->src_dmabufintl[i].dmabuf_fd) {
+				new_strm_node->element.in_buf_pointer =
+					mpgmuxts->src_dmabufintl[i].dmabuf_addr;
+				new_strm_node->element.dmabuf_id =
+					mpgmuxts->src_dmabufintl[i].buf_id;
+				break;
+			}
+		}
+
+		/* No dma buf found with srcbuf_id*/
+		if (i == XTSMUX_MAXIN_STRM) {
+			dev_err(mpgmuxts->dev, "No DMA buffer with %d",
+				stream_data->srcbuf_id);
+			return -ENOMEM;
+		}
+	}
+
+	new_strm_node->strm_phy_addr = (u64)strm_phy_addr;
+	new_strm_node->node_number = mpgmuxts->stcxt_node_cnt + 1;
+	mpgmuxts->stcxt_node_cnt++;
+	new_strm_node->node_status = UPDATED_BY_DRIVER;
+	new_strm_node->error_code = NO_ERROR;
+	new_strm_node->tail_pointer = 0;
+
+	spin_lock_irqsave(&mpgmuxts->lock, flags);
+	/* If it is not first stream in stream node linked list find
+	 * physical address of current node and add to last node in list
+	 */
+	if (!list_empty_careful(&mpgmuxts->strm_node)) {
+		prev_strm_node = list_last_entry(&mpgmuxts->strm_node,
+						 struct stream_context_node,
+						 node);
+		prev_strm_node->tail_pointer = new_strm_node->strm_phy_addr;
+	}
+	/* update the list and stream count */
+	wmb();
+	list_add_tail(&new_strm_node->node, &mpgmuxts->strm_node);
+	atomic_inc(&mpgmuxts->stream_count);
+	spin_unlock_irqrestore(&mpgmuxts->lock, flags);
+
+	return 0;
+}
+
+static int xlnx_tsmux_set_stream_desc(struct xlnx_tsmux *mpgmuxts,
+				      void __user *arg)
+{
+	struct stream_context_in *stream_data;
+	int ret = 0;
+
+	stream_data = kzalloc(sizeof(*stream_data), GFP_KERNEL);
+	if (!stream_data)
+		return -ENOMEM;
+
+	ret = copy_from_user(stream_data, arg,
+			     sizeof(struct stream_context_in));
+	if (ret) {
+		dev_err(mpgmuxts->dev, "Failed to copy stream data from user");
+		goto error_free;
+	}
+
+	ret = xlnx_tsmux_enqueue_stream_context(mpgmuxts, stream_data);
+
+error_free:
+	kfree(stream_data);
+
+	return ret;
+}
+
+static int xlnx_tsmux_ioctl_set_stream_context(struct xlnx_tsmux *mpgmuxts,
+					       void __user *arg)
+{
+	int ret;
+
+	ret = xlnx_tsmux_set_stream_desc(mpgmuxts, arg);
+	if (ret < 0) {
+		dev_err(mpgmuxts->dev, "Setting stream descripter failed");
+		return ret;
+	}
+
+	return 0;
+}
+
+static enum xlnx_tsmux_status xlnx_tsmux_get_device_status(struct xlnx_tsmux *
+							   mpgmuxts)
+{
+	enum xlnx_tsmux_status ip_status;
+
+	ip_status = xlnx_tsmux_get_status(mpgmuxts);
+
+	if (ip_status == MPG2MUX_ERROR) {
+		dev_err(mpgmuxts->dev, "Failed to get device status");
+		return -EACCES;
+	}
+
+	if (ip_status == MPG2MUX_BUSY)
+		return -EBUSY;
+
+	return MPG2MUX_READY;
+}
+
+static int xlnx_tsmux_ioctl_start(struct xlnx_tsmux *mpgmuxts)
+{
+	enum xlnx_tsmux_status ip_stat;
+	int cnt, ret;
+
+	/* get IP status */
+	ip_stat = xlnx_tsmux_get_device_status(mpgmuxts);
+	if (ip_stat != MPG2MUX_READY) {
+		dev_err(mpgmuxts->dev, "device is busy");
+		return ip_stat;
+	}
+
+	if (list_empty(&mpgmuxts->mux_node) ||
+	    list_empty(&mpgmuxts->strm_node)) {
+		dev_err(mpgmuxts->dev, "No stream or mux to start device");
+		return -EIO;
+	}
+
+	cnt = atomic_read(&mpgmuxts->stream_count);
+	atomic_set(&mpgmuxts->intn_stream_count, cnt);
+
+	/* update streamid table */
+	ret = xlnx_tsmux_update_intstrm_tbl(mpgmuxts);
+
+	if (ret < 0) {
+		dev_err(mpgmuxts->dev, "Update streamid intn table failed\n");
+		return ret;
+	}
+	return xlnx_tsmux_start_muxer(mpgmuxts);
+}
+
+static void xlnx_tsmux_free_dmalloc(struct xlnx_tsmux *mpgmuxts)
+{
+	dma_pool_destroy(mpgmuxts->strm_ctx_pool);
+	dma_pool_destroy(mpgmuxts->mux_ctx_pool);
+}
+
+static int xlnx_tsmux_ioctl_stop(struct xlnx_tsmux *mpgmuxts)
+{
+	enum xlnx_tsmux_status ip_stat;
+	unsigned long flags;
+
+	ip_stat = xlnx_tsmux_get_device_status(mpgmuxts);
+	if (ip_stat != MPG2MUX_READY) {
+		dev_err(mpgmuxts->dev, "device is busy");
+		return ip_stat;
+	}
+
+	/* Free all driver allocated memory and reset linked list
+	 * Reset IP registers
+	 */
+	xlnx_tsmux_free_dmalloc(mpgmuxts);
+	spin_lock_irqsave(&mpgmuxts->lock, flags);
+	INIT_LIST_HEAD(&mpgmuxts->strm_node);
+	INIT_LIST_HEAD(&mpgmuxts->mux_node);
+	spin_unlock_irqrestore(&mpgmuxts->lock, flags);
+	xlnx_tsmux_stop_muxer(mpgmuxts);
+
+	return 0;
+}
+
+static int xlnx_tsmux_ioctl_get_status(struct xlnx_tsmux *mpgmuxts,
+				       void __user *arg)
+{
+	int ret;
+	enum xlnx_tsmux_status ip_stat;
+
+	ip_stat = xlnx_tsmux_get_device_status(mpgmuxts);
+
+	ret = copy_to_user(arg, (void *)&ip_stat,
+			   (unsigned long)(sizeof(enum xlnx_tsmux_status)));
+	if (ret) {
+		dev_err(mpgmuxts->dev, "Unable to copy device status to user");
+		return -EACCES;
+	}
+
+	return 0;
+}
+
+static int xlnx_tsmux_ioctl_get_outbufinfo(struct xlnx_tsmux *mpgmuxts,
+					   void __user *arg)
+{
+	int ret;
+	int out_index;
+	struct out_buffer out_info;
+
+	out_info.buf_write = mpgmuxts->outbuf_written;
+	mpgmuxts->outbuf_written = 0;
+	out_index = atomic_read(&mpgmuxts->outbuf_idx);
+	if (out_index)
+		out_info.buf_id = 0;
+	else
+		out_info.buf_id = 1;
+
+	ret = copy_to_user(arg, (void *)&out_info,
+			   (unsigned long)(sizeof(struct out_buffer)));
+	if (ret) {
+		dev_err(mpgmuxts->dev, "Unable to copy outbuf info");
+		return -EACCES;
+	}
+
+	return 0;
+}
+
+static int xlnx_tsmux_enqueue_mux_context(struct xlnx_tsmux *mpgmuxts,
+					  struct muxer_context_in *mux_data)
+{
+	struct muxer_context *new_mux_node;
+	u32 out_index;
+	void *kaddr_mux_node;
+	dma_addr_t mux_phy_addr;
+	unsigned long flags;
+	s32 i;
+
+	kaddr_mux_node = dma_pool_alloc(mpgmuxts->mux_ctx_pool,
+					GFP_KERNEL | GFP_DMA32,
+					&mux_phy_addr);
+
+	new_mux_node = (struct muxer_context *)kaddr_mux_node;
+	if (!new_mux_node)
+		return -EAGAIN;
+
+	new_mux_node->node_status = UPDATED_BY_DRIVER;
+	new_mux_node->mux_phy_addr = (u64)mux_phy_addr;
+
+	/* Check for external dma buffer */
+	if (!mux_data->is_dmabuf) {
+		out_index = 0;
+		new_mux_node->dst_buf_start_addr =
+			(u64)mpgmuxts->dstbuf_addrs[out_index];
+		new_mux_node->dst_buf_size = mpgmuxts->dstbuf_size;
+		if (out_index)
+			atomic_set(&mpgmuxts->outbuf_idx, 0);
+		else
+			atomic_set(&mpgmuxts->outbuf_idx, 1);
+	} else {
+		for (i = 0; i < XTSMUX_MAXOUT_STRM; i++) {
+			if (mux_data->dstbuf_id ==
+			   mpgmuxts->dst_dmabufintl[i].dmabuf_fd) {
+				new_mux_node->dst_buf_start_addr =
+					mpgmuxts->dst_dmabufintl[i].dmabuf_addr;
+				break;
+			}
+		}
+		if (i == XTSMUX_MAXOUT_STRM) {
+			dev_err(mpgmuxts->dev, "No DMA buffer with %d",
+				mux_data->dstbuf_id);
+			return -ENOMEM;
+		}
+		new_mux_node->dst_buf_size = mux_data->dmabuf_size;
+	}
+	new_mux_node->error_code = MUXER_NO_ERROR;
+
+	spin_lock_irqsave(&mpgmuxts->lock, flags);
+	list_add_tail(&new_mux_node->node, &mpgmuxts->mux_node);
+	spin_unlock_irqrestore(&mpgmuxts->lock, flags);
+
+	return 0;
+}
+
+static int xlnx_tsmux_set_mux_desc(struct xlnx_tsmux *mpgmuxts,
+				   void __user *arg)
+{
+	struct muxer_context_in *mux_data;
+	int ret = 0;
+
+	mux_data = kzalloc(sizeof(*mux_data), GFP_KERNEL);
+	if (!mux_data)
+		return -ENOMEM;
+
+	ret = copy_from_user(mux_data, arg,
+			     sizeof(struct muxer_context_in));
+	if (ret) {
+		dev_err(mpgmuxts->dev, "failed to copy muxer data from user");
+		goto kmem_free;
+	}
+
+	return xlnx_tsmux_enqueue_mux_context(mpgmuxts, mux_data);
+
+kmem_free:
+	kfree(mux_data);
+
+	return ret;
+}
+
+static int xlnx_tsmux_ioctl_set_mux_context(struct xlnx_tsmux *mpgmuxts,
+					    void __user *arg)
+{
+	int ret;
+
+	ret = xlnx_tsmux_set_mux_desc(mpgmuxts, arg);
+	if (ret < 0)
+		dev_dbg(mpgmuxts->dev, "Setting mux context failed");
+
+	return ret;
+}
+
+static int xlnx_tsmux_ioctl_verify_dmabuf(struct xlnx_tsmux *mpgmuxts,
+					  void __user *arg)
+{
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	struct xlnx_tsmux_dmabuf_info *dbuf_info;
+	s32 i;
+	int ret = 0;
+
+	dbuf_info = kzalloc(sizeof(*dbuf_info), GFP_KERNEL);
+	if (!dbuf_info)
+		return -ENOMEM;
+
+	ret = copy_from_user(dbuf_info, arg,
+			     sizeof(struct xlnx_tsmux_dmabuf_info));
+	if (ret) {
+		dev_err(mpgmuxts->dev, "Failed to copy from user");
+		goto dmak_free;
+	}
+	if (dbuf_info->dir != DMA_TO_MPG2MUX &&
+	    dbuf_info->dir != DMA_FROM_MPG2MUX) {
+		dev_err(mpgmuxts->dev, "Incorrect DMABUF direction %d",
+			dbuf_info->dir);
+		ret = -EINVAL;
+		goto dmak_free;
+	}
+	dbuf = dma_buf_get(dbuf_info->buf_fd);
+	if (IS_ERR(dbuf)) {
+		dev_err(mpgmuxts->dev, "dma_buf_get fail fd %d direction %d",
+			dbuf_info->buf_fd, dbuf_info->dir);
+		ret = PTR_ERR(dbuf);
+		goto dmak_free;
+	}
+	attach = dma_buf_attach(dbuf, mpgmuxts->dev);
+	if (IS_ERR(attach)) {
+		dev_err(mpgmuxts->dev, "dma_buf_attach fail fd %d dir %d",
+			dbuf_info->buf_fd, dbuf_info->dir);
+		ret = PTR_ERR(attach);
+		goto err_dmabuf_put;
+	}
+	sgt = dma_buf_map_attachment(attach,
+				     (enum dma_data_direction)(dbuf_info->dir));
+	if (IS_ERR(sgt)) {
+		dev_err(mpgmuxts->dev, "dma_buf_map_attach fail fd %d dir %d",
+			dbuf_info->buf_fd, dbuf_info->dir);
+		ret = PTR_ERR(sgt);
+		goto err_dmabuf_detach;
+	}
+
+	if (sgt->nents > 1) {
+		ret = -EIO;
+		dev_dbg(mpgmuxts->dev, "Not contig nents %d fd %d direction %d",
+			sgt->nents, dbuf_info->buf_fd, dbuf_info->dir);
+		goto err_dmabuf_unmap_attachment;
+	}
+	dev_dbg(mpgmuxts->dev, "dmabuf %s is physically contiguous",
+		(dbuf_info->dir ==
+		 DMA_TO_MPG2MUX ? "Source" : "Destination"));
+
+	if (dbuf_info->dir == DMA_TO_MPG2MUX) {
+		for (i = 0; i < XTSMUX_MAXIN_STRM; i++) {
+			if (!mpgmuxts->src_dmabufintl[i].buf_id) {
+				mpgmuxts->src_dmabufintl[i].dbuf = dbuf;
+				mpgmuxts->src_dmabufintl[i].attach = attach;
+				mpgmuxts->src_dmabufintl[i].sgt = sgt;
+				mpgmuxts->src_dmabufintl[i].dmabuf_addr =
+						sg_dma_address(sgt->sgl);
+				mpgmuxts->src_dmabufintl[i].dmabuf_fd =
+							dbuf_info->buf_fd;
+				mpgmuxts->src_dmabufintl[i].buf_id = i + 1;
+				dev_dbg(mpgmuxts->dev,
+					"%s: phy-addr=0x%llx for src dmabuf=%d",
+					__func__,
+					mpgmuxts->src_dmabufintl[i].dmabuf_addr,
+					mpgmuxts->src_dmabufintl[i].dmabuf_fd);
+				break;
+			}
+		}
+		/* External src streams more than XTSMUX_MAXIN_STRM
+		 * can not be handled
+		 */
+		if (i == XTSMUX_MAXIN_STRM) {
+			ret = -EIO;
+			dev_dbg(mpgmuxts->dev, "src DMA bufs more than %d",
+				XTSMUX_MAXIN_STRM);
+			goto err_dmabuf_unmap_attachment;
+		}
+	} else {
+		for (i = 0; i < XTSMUX_MAXOUT_STRM; i++) {
+			if (!mpgmuxts->dst_dmabufintl[i].buf_id) {
+				mpgmuxts->dst_dmabufintl[i].dbuf = dbuf;
+				mpgmuxts->dst_dmabufintl[i].attach = attach;
+				mpgmuxts->dst_dmabufintl[i].sgt = sgt;
+				mpgmuxts->dst_dmabufintl[i].dmabuf_addr =
+						sg_dma_address(sgt->sgl);
+				mpgmuxts->dst_dmabufintl[i].dmabuf_fd =
+						dbuf_info->buf_fd;
+				mpgmuxts->dst_dmabufintl[i].buf_id = i + 1;
+				dev_dbg(mpgmuxts->dev,
+					"phy-addr=0x%llx for src dmabuf=%d",
+					mpgmuxts->dst_dmabufintl[i].dmabuf_addr,
+					mpgmuxts->dst_dmabufintl[i].dmabuf_fd);
+				break;
+			}
+		}
+		/* External dst streams more than XTSMUX_MAXOUT_STRM
+		 * can not be handled
+		 */
+		if (i == XTSMUX_MAXOUT_STRM) {
+			ret = -EIO;
+			dev_dbg(mpgmuxts->dev, "dst DMA bufs more than %d",
+				XTSMUX_MAXOUT_STRM);
+			goto err_dmabuf_unmap_attachment;
+		}
+	}
+
+	return 0;
+
+err_dmabuf_unmap_attachment:
+	dma_buf_unmap_attachment(attach, sgt,
+				 (enum dma_data_direction)dbuf_info->dir);
+err_dmabuf_detach:
+	dma_buf_detach(dbuf, attach);
+err_dmabuf_put:
+	dma_buf_put(dbuf);
+dmak_free:
+	kfree(dbuf_info);
+
+	return ret;
+}
+
+static long xlnx_tsmux_ioctl(struct file *fptr,
+			     unsigned int cmd, unsigned long data)
+{
+	struct xlnx_tsmux *mpgmuxts;
+	void __user *arg;
+	int ret;
+
+	mpgmuxts = fptr->private_data;
+	if (!mpgmuxts)
+		return -EINVAL;
+
+	arg = (void __user *)data;
+	switch (cmd) {
+	case MPG2MUX_INBUFALLOC:
+		ret = xlnx_tsmux_ioctl_srcbuf_alloc(mpgmuxts, arg);
+		break;
+	case MPG2MUX_INBUFDEALLOC:
+		ret = xlnx_tsmux_ioctl_srcbuf_dealloc(mpgmuxts);
+		break;
+	case MPG2MUX_OUTBUFALLOC:
+		ret = xlnx_tsmux_ioctl_dstbuf_alloc(mpgmuxts, arg);
+		break;
+	case MPG2MUX_OUTBUFDEALLOC:
+		ret = xlnx_tsmux_ioctl_dstbuf_dealloc(mpgmuxts);
+		break;
+	case MPG2MUX_STBLALLOC:
+		ret = xlnx_tsmux_ioctl_strmtbl_alloc(mpgmuxts, arg);
+		break;
+	case MPG2MUX_STBLDEALLOC:
+		ret = xlnx_tsmux_ioctl_strmtbl_dealloc(mpgmuxts);
+		break;
+	case MPG2MUX_TBLUPDATE:
+		ret = xlnx_tsmux_ioctl_update_strmtbl(mpgmuxts, arg);
+		break;
+	case MPG2MUX_SETSTRM:
+		ret = xlnx_tsmux_ioctl_set_stream_context(mpgmuxts, arg);
+		break;
+	case MPG2MUX_START:
+		ret = xlnx_tsmux_ioctl_start(mpgmuxts);
+		break;
+	case MPG2MUX_STOP:
+		ret = xlnx_tsmux_ioctl_stop(mpgmuxts);
+		break;
+	case MPG2MUX_STATUS:
+		ret = xlnx_tsmux_ioctl_get_status(mpgmuxts, arg);
+		break;
+	case MPG2MUX_GETOUTBUF:
+		ret = xlnx_tsmux_ioctl_get_outbufinfo(mpgmuxts, arg);
+		break;
+	case MPG2MUX_SETMUX:
+		ret = xlnx_tsmux_ioctl_set_mux_context(mpgmuxts, arg);
+		break;
+	case MPG2MUX_VDBUF:
+		ret = xlnx_tsmux_ioctl_verify_dmabuf(mpgmuxts, arg);
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (ret < 0)
+		dev_err(mpgmuxts->dev, "ioctl %d failed\n", cmd);
+
+	return ret;
+}
+
+static int xlnx_tsmux_mmap(struct file *fp, struct vm_area_struct *vma)
+{
+	struct xlnx_tsmux *mpgmuxts = fp->private_data;
+	int ret, buf_id;
+
+	if (!mpgmuxts)
+		return -ENODEV;
+
+	buf_id = vma->vm_pgoff;
+
+	if (buf_id < mpgmuxts->num_inbuf) {
+		if (!mpgmuxts->srcbuf_addrs[buf_id]) {
+			dev_err(mpgmuxts->dev, "Mem not allocated for src %d",
+				buf_id);
+			return -EINVAL;
+		}
+		vma->vm_page_prot = pgprot_writecombine(vma->vm_page_prot);
+		ret = remap_pfn_range(vma, vma->vm_start,
+				      mpgmuxts->srcbuf_addrs[buf_id] >>
+				      PAGE_SHIFT, vma->vm_end - vma->vm_start,
+				      vma->vm_page_prot);
+		if (ret) {
+			dev_err(mpgmuxts->dev, "mmap fail bufid = %d", buf_id);
+			return -EINVAL;
+		}
+	} else if (buf_id < (mpgmuxts->num_inbuf + mpgmuxts->num_outbuf)) {
+		buf_id -= mpgmuxts->num_inbuf;
+		if (!mpgmuxts->dstbuf_addrs[buf_id]) {
+			dev_err(mpgmuxts->dev, "Mem not allocated fordst %d",
+				buf_id);
+			return -EINVAL;
+		}
+		vma->vm_page_prot = pgprot_writecombine(vma->vm_page_prot);
+		ret =
+		remap_pfn_range(vma, vma->vm_start,
+				mpgmuxts->dstbuf_addrs[buf_id] >> PAGE_SHIFT,
+				vma->vm_end - vma->vm_start, vma->vm_page_prot);
+		if (ret) {
+			dev_err(mpgmuxts->dev, "mmap fail buf_id = %d", buf_id);
+			ret = -EINVAL;
+		}
+	} else {
+		dev_err(mpgmuxts->dev, "Wrong buffer id -> %d buf", buf_id);
+		return -EINVAL;
+	}
+	fp->private_data = mpgmuxts;
+	return 0;
+}
+
+static __poll_t xlnx_tsmux_poll(struct file *fptr, poll_table *wait)
+{
+	struct xlnx_tsmux *mpgmuxts = fptr->private_data;
+
+	poll_wait(fptr, &mpgmuxts->waitq, wait);
+
+	if (xlnx_tsmux_read(mpgmuxts, XTSMUX_LAST_NODE_PROCESSED))
+		return POLLIN | POLLPRI;
+
+	return 0;
+}
+
+static const struct file_operations mpg2mux_fops = {
+	.open = xlnx_tsmux_open,
+	.release = xlnx_tsmux_release,
+	.unlocked_ioctl = xlnx_tsmux_ioctl,
+	.mmap = xlnx_tsmux_mmap,
+	.poll = xlnx_tsmux_poll,
+};
+
+static void xlnx_tsmux_free_dmabufintl(struct xlnx_tsmux_dmabufintl
+				       *intl_dmabuf, u16 dmabuf_id,
+				       enum xlnx_tsmux_dma_dir dir)
+{
+	unsigned int i = dmabuf_id - 1;
+
+	if (intl_dmabuf[i].dmabuf_fd) {
+		dma_buf_unmap_attachment(intl_dmabuf[i].attach,
+					 intl_dmabuf[i].sgt,
+					 (enum dma_data_direction)dir);
+		dma_buf_detach(intl_dmabuf[i].dbuf, intl_dmabuf[i].attach);
+		dma_buf_put(intl_dmabuf[i].dbuf);
+		intl_dmabuf[i].dmabuf_fd = 0;
+		intl_dmabuf[i].buf_id = 0;
+	}
+}
+
+static int xlnx_tsmux_update_complete(struct xlnx_tsmux *mpgmuxts)
+{
+	struct stream_context_node *tstrm_node;
+	struct muxer_context *temp_mux;
+	u32 num_strm_node, i;
+	u32 num_strms;
+	unsigned long flags;
+
+	num_strm_node = xlnx_tsmux_read(mpgmuxts, XTSMUX_LAST_NODE_PROCESSED);
+	if (num_strm_node == 0)
+		return -1;
+
+	/* Removing completed stream nodes from the list  */
+	spin_lock_irqsave(&mpgmuxts->lock, flags);
+	num_strms = atomic_read(&mpgmuxts->intn_stream_count);
+	for (i = 0; i < num_strms; i++) {
+		tstrm_node =
+			list_first_entry(&mpgmuxts->strm_node,
+					 struct stream_context_node, node);
+		list_del(&tstrm_node->node);
+		atomic_dec(&mpgmuxts->stream_count);
+		if (tstrm_node->element.dmabuf_id)
+			xlnx_tsmux_free_dmabufintl
+				(mpgmuxts->src_dmabufintl,
+				 tstrm_node->element.dmabuf_id,
+				 DMA_TO_MPG2MUX);
+		if (tstrm_node->node_number == num_strm_node) {
+			dma_pool_free(mpgmuxts->strm_ctx_pool, tstrm_node,
+				      tstrm_node->strm_phy_addr);
+			break;
+		}
+	}
+
+	/* Removing completed mux nodes from the list  */
+	temp_mux = list_first_entry(&mpgmuxts->mux_node, struct muxer_context,
+				    node);
+	mpgmuxts->outbuf_written = temp_mux->dst_buf_written;
+
+	list_del(&temp_mux->node);
+	spin_unlock_irqrestore(&mpgmuxts->lock, flags);
+
+	return 0;
+}
+
+static irqreturn_t xlnx_tsmux_intr_handler(int irq, void *ctx)
+{
+	u32 status;
+	struct xlnx_tsmux *mpgmuxts = (struct xlnx_tsmux *)ctx;
+
+	status = xlnx_tsmux_read(mpgmuxts, XTSMUX_ISR_STAT);
+	status &= XTSMUX_IER_ENABLE_MASK;
+
+	if (status) {
+		xlnx_tsmux_write(mpgmuxts, XTSMUX_ISR_STAT, status);
+		xlnx_tsmux_update_complete(mpgmuxts);
+		if (mpgmuxts->outbuf_written)
+			wake_up_interruptible(&mpgmuxts->waitq);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int xlnx_tsmux_probe(struct platform_device *pdev)
+{
+	struct xlnx_tsmux *mpgmuxts;
+	struct device *dev = &pdev->dev;
+	struct device *dev_crt;
+	struct resource *dev_resrc;
+	int ret = -1;
+	unsigned long flags;
+
+	/* DRIVER_MAX_DEV is to limit the number of instances, but
+	 * Initial version is tested with single instance only.
+	 * TODO: replace atomic_read with ida_simple_get
+	 */
+	if (atomic_read(&xlnx_tsmux_ndevs) >= DRIVER_MAX_DEV) {
+		dev_err(&pdev->dev, "Limit of %d number of device is reached",
+			DRIVER_MAX_DEV);
+		return -EIO;
+	}
+
+	mpgmuxts = devm_kzalloc(&pdev->dev, sizeof(struct xlnx_tsmux),
+				GFP_KERNEL);
+	if (!mpgmuxts)
+		return -ENOMEM;
+	mpgmuxts->dev = &pdev->dev;
+	dev_resrc = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mpgmuxts->iomem = devm_ioremap_resource(mpgmuxts->dev, dev_resrc);
+	if (IS_ERR(mpgmuxts->iomem))
+		return PTR_ERR(mpgmuxts->iomem);
+
+	mpgmuxts->irq = irq_of_parse_and_map(mpgmuxts->dev->of_node, 0);
+	if (!mpgmuxts->irq) {
+		dev_err(mpgmuxts->dev, "Unable to get IRQ");
+		return -EINVAL;
+	}
+
+	mpgmuxts->ap_clk = devm_clk_get(dev, "ap_clk");
+	if (IS_ERR(mpgmuxts->ap_clk)) {
+		ret = PTR_ERR(mpgmuxts->ap_clk);
+		dev_err(dev, "failed to get ap clk %d\n", ret);
+		goto cdev_err;
+	}
+	ret = clk_prepare_enable(mpgmuxts->ap_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable ap clk %d\n", ret);
+		goto err_disable_ap_clk;
+	}
+
+	/* Initializing variables used in Muxer */
+	spin_lock_irqsave(&mpgmuxts->lock, flags);
+	INIT_LIST_HEAD(&mpgmuxts->strm_node);
+	INIT_LIST_HEAD(&mpgmuxts->mux_node);
+	spin_unlock_irqrestore(&mpgmuxts->lock, flags);
+	mpgmuxts->strm_ctx_pool = dma_pool_create("strcxt_pool", mpgmuxts->dev,
+						  XTSMUX_POOL_SIZE,
+						  XTSMUX_POOL_ALIGN,
+						  XTSMUX_POOL_SIZE *
+						  XTSMUX_MAXIN_TLSTRM);
+	if (!mpgmuxts->strm_ctx_pool) {
+		dev_err(mpgmuxts->dev, "Allocation fail for strm ctx pool");
+		return -ENOMEM;
+	}
+
+	mpgmuxts->mux_ctx_pool = dma_pool_create("muxcxt_pool", mpgmuxts->dev,
+						 XTSMUX_POOL_SIZE,
+						 XTSMUX_POOL_SIZE,
+						 XTSMUX_POOL_SIZE *
+						 XTSMUX_MAXIN_TLSTRM);
+
+	if (!mpgmuxts->mux_ctx_pool) {
+		dev_err(mpgmuxts->dev, "Allocation fail for mux ctx pool");
+		goto mux_err;
+	}
+
+	init_waitqueue_head(&mpgmuxts->waitq);
+
+	ret = devm_request_irq(mpgmuxts->dev, mpgmuxts->irq,
+			       xlnx_tsmux_intr_handler, IRQF_SHARED,
+			       DRIVER_NAME, mpgmuxts);
+
+	if (ret < 0) {
+		dev_err(mpgmuxts->dev, "Unable to register IRQ");
+		goto mux_err;
+	}
+
+	cdev_init(&mpgmuxts->chdev, &mpg2mux_fops);
+	mpgmuxts->chdev.owner = THIS_MODULE;
+	mpgmuxts->id = atomic_read(&xlnx_tsmux_ndevs);
+	ret = cdev_add(&mpgmuxts->chdev, MKDEV(MAJOR(xlnx_tsmux_devt),
+					       mpgmuxts->id), 1);
+
+	if (ret < 0) {
+		dev_err(mpgmuxts->dev, "cdev_add failed");
+		goto cadd_err;
+	}
+
+	dev_crt = device_create(xlnx_tsmux_class, mpgmuxts->dev,
+				MKDEV(MAJOR(xlnx_tsmux_devt), mpgmuxts->id),
+				mpgmuxts, "mpgmuxts%d", mpgmuxts->id);
+
+	if (IS_ERR(dev_crt)) {
+		ret = PTR_ERR(dev_crt);
+		dev_err(mpgmuxts->dev, "Unable to create device");
+		goto cdev_err;
+	}
+
+	dev_info(mpgmuxts->dev,
+		 "Xilinx mpeg2 TS muxer device probe completed");
+
+	atomic_inc(&xlnx_tsmux_ndevs);
+
+	return 0;
+
+err_disable_ap_clk:
+	clk_disable_unprepare(mpgmuxts->ap_clk);
+cdev_err:
+	cdev_del(&mpgmuxts->chdev);
+	device_destroy(xlnx_tsmux_class, MKDEV(MAJOR(xlnx_tsmux_devt),
+					       mpgmuxts->id));
+cadd_err:
+	dma_pool_destroy(mpgmuxts->mux_ctx_pool);
+mux_err:
+	dma_pool_destroy(mpgmuxts->strm_ctx_pool);
+
+	return ret;
+}
+
+static int xlnx_tsmux_remove(struct platform_device *pdev)
+{
+	struct xlnx_tsmux *mpgmuxts;
+
+	mpgmuxts = platform_get_drvdata(pdev);
+	if (!mpgmuxts || !xlnx_tsmux_class)
+		return -EIO;
+	dma_pool_destroy(mpgmuxts->mux_ctx_pool);
+	dma_pool_destroy(mpgmuxts->strm_ctx_pool);
+
+	device_destroy(xlnx_tsmux_class, MKDEV(MAJOR(xlnx_tsmux_devt),
+					       mpgmuxts->id));
+	cdev_del(&mpgmuxts->chdev);
+	atomic_dec(&xlnx_tsmux_ndevs);
+	clk_disable_unprepare(mpgmuxts->ap_clk);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_tsmux_of_match[] = {
+	{ .compatible = "xlnx,tsmux-1.0", },
+	{ }
+};
+
+static struct platform_driver xlnx_tsmux_driver = {
+	.probe = xlnx_tsmux_probe,
+	.remove = xlnx_tsmux_remove,
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = xlnx_tsmux_of_match,
+	},
+};
+
+static int __init xlnx_tsmux_mod_init(void)
+{
+	int err;
+
+	xlnx_tsmux_class = class_create(THIS_MODULE, DRIVER_NAME);
+	if (IS_ERR(xlnx_tsmux_class)) {
+		pr_err("%s : Unable to create driver class", __func__);
+		return PTR_ERR(xlnx_tsmux_class);
+	}
+
+	err = alloc_chrdev_region(&xlnx_tsmux_devt, 0, DRIVER_MAX_DEV,
+				  DRIVER_NAME);
+	if (err < 0) {
+		pr_err("%s : Unable to get major number", __func__);
+		goto err_class;
+	}
+
+	err = platform_driver_register(&xlnx_tsmux_driver);
+	if (err < 0) {
+		pr_err("%s : Unable to register %s driver", __func__,
+		       DRIVER_NAME);
+		goto err_driver;
+	}
+
+	return 0;
+
+err_driver:
+	unregister_chrdev_region(xlnx_tsmux_devt, DRIVER_MAX_DEV);
+err_class:
+	class_destroy(xlnx_tsmux_class);
+
+	return err;
+}
+
+static void __exit xlnx_tsmux_mod_exit(void)
+{
+	platform_driver_unregister(&xlnx_tsmux_driver);
+	unregister_chrdev_region(xlnx_tsmux_devt, DRIVER_MAX_DEV);
+	class_destroy(xlnx_tsmux_class);
+	xlnx_tsmux_class = NULL;
+}
+
+module_init(xlnx_tsmux_mod_init);
+module_exit(xlnx_tsmux_mod_exit);
+
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("Xilinx mpeg2 transport stream muxer IP driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnxsync/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnxsync/Kconfig
@@ -0,0 +1,11 @@
+config XLNX_SYNC
+	tristate "Xilinx Synchronizer"
+	depends on ARCH_ZYNQMP
+	help
+	  This driver is developed for Xilinx Synchronizer IP. It is used to
+	  monitor the AXI addresses of the producer and initiate the
+	  consumer to start earlier, thereby reducing the latency to process
+	  the data.
+
+	  To compile this driver as a module, choose M here.
+	  If unsure, choose N
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnxsync/MAINTAINERS
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnxsync/MAINTAINERS
@@ -0,0 +1,4 @@
+XILINX SYNCHRONIZER DRIVER
+M:	Vishal Sagar <vishal.sagar@xilinx.com>
+S:	Maintained
+F:	drivers/staging/xlnxsync
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnxsync/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnxsync/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_XLNX_SYNC) += xlnxsync.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnxsync/dt-binding.txt
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnxsync/dt-binding.txt
@@ -0,0 +1,34 @@
+Xilinx Synchronizer
+-------------------
+
+The Xilinx Synchronizer is used for buffer synchronization between
+producer and consumer blocks. It manages to do so by tapping onto the bus
+where the producer block is writing frame data to memory and consumer block is
+reading the frame data from memory.
+
+It can work on the encode path with max 4 channels or on decode path with
+max 2 channels.
+
+Required properties:
+- compatible : Must contain "xlnx,sync-ip-1.0"
+- reg: Physical base address and length of the registers set for the device.
+- interrupts: Contains the interrupt line number.
+- interrupt-parent: phandle to interrupt controller.
+- clock-names: The input clock names for axilite, producer and consumer clock.
+- clocks: Reference to the clock that drives the axi interface, producer and consumer.
+- xlnx,num-chan: Range from 1 to 2 for decode.
+		 Range from 1 to 4 for encode.
+
+Optional properties:
+- xlnx,encode: Present if IP configured for encoding path, else absent.
+
+v_sync_vcu: subframe_sync_vcu@a00e0000 {
+	compatible = "xlnx,sync-ip-1.0";
+	reg = <0x0 0xa00e0000 0x0 0x10000>;
+	interrupt-parent = <&gic>;
+	interrupts = <0 96 4>;
+	clock-names = "s_axi_ctrl_aclk", "s_axi_mm_p_aclk", "s_axi_mm_aclk";
+	clocks = <&vid_s_axi_clk>, <&vid_stream_clk>, <&vid_stream_clk>;
+	xlnx,num-chan = <4>;
+	xlnx,encode;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xlnxsync/xlnxsync.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xlnxsync/xlnxsync.c
@@ -0,0 +1,1494 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Synchronizer IP driver
+ *
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author: Vishal Sagar <vishal.sagar@xilinx.com>
+ *
+ * This driver is used to control the Xilinx Synchronizer IP
+ * to achieve sub frame latency for encode and decode with VCU.
+ * This is done by monitoring the address lines for specific values.
+ */
+
+#include <linux/cdev.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioctl.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/poll.h>
+#include <linux/uaccess.h>
+#include <linux/xlnxsync.h>
+
+/* Register offsets and bit masks */
+#define XLNXSYNC_CTRL_REG		0x00
+#define XLNXSYNC_ISR_REG		0x04
+/* Producer Luma/Chroma Start/End Address */
+#define XLNXSYNC_PL_START_LO_REG	0x08
+#define XLNXSYNC_PL_START_HI_REG	0x0C
+#define XLNXSYNC_PC_START_LO_REG	0x20
+#define XLNXSYNC_PC_START_HI_REG	0x24
+#define XLNXSYNC_PL_END_LO_REG		0x38
+#define XLNXSYNC_PL_END_HI_REG		0x3C
+#define XLNXSYNC_PC_END_LO_REG		0x50
+#define XLNXSYNC_PC_END_HI_REG		0x54
+#define XLNXSYNC_L_MARGIN_REG		0x68
+#define XLNXSYNC_C_MARGIN_REG		0x74
+#define XLNXSYNC_IMR_REG		0x80
+#define XLNXSYNC_DBG_REG		0x84
+/* Consumer Luma/Chroma Start/End Address */
+#define XLNXSYNC_CL_START_LO_REG	0x88
+#define XLNXSYNC_CL_START_HI_REG	0x8C
+#define XLNXSYNC_CC_START_LO_REG	0xA0
+#define XLNXSYNC_CC_START_HI_REG	0xA4
+#define XLNXSYNC_CL_END_LO_REG		0xB8
+#define XLNXSYNC_CL_END_HI_REG		0xBC
+#define XLNXSYNC_CC_END_LO_REG		0xD0
+#define XLNXSYNC_CC_END_HI_REG		0xD4
+
+/* Luma/Chroma Core offset registers */
+#define XLNXSYNC_LCOREOFF_REG		0x400
+#define XLNXSYNC_CCOREOFF_REG		0x410
+#define XLNXSYNC_COREOFF_NEXT		0x4
+
+#define XLNXSYNC_CTRL_ENCDEC_MASK	BIT(0)
+#define XLNXSYNC_CTRL_ENABLE_MASK	BIT(1)
+#define XLNXSYNC_CTRL_INTR_EN_MASK	BIT(2)
+#define XLNXSYNC_CTRL_SOFTRESET		BIT(3)
+
+#define XLNXSYNC_ISR_PROD_SYNC_FAIL_MASK BIT(0)
+#define XLNXSYNC_ISR_PROD_WDG_ERR_MASK	BIT(1)
+/* Producer related */
+#define XLNXSYNC_ISR_PLDONE_SHIFT	(2)
+#define XLNXSYNC_ISR_PLDONE_MASK	GENMASK(3, 2)
+#define XLNXSYNC_ISR_PLSKIP_MASK	BIT(4)
+#define XLNXSYNC_ISR_PLVALID_MASK	BIT(5)
+#define XLNXSYNC_ISR_PCDONE_SHIFT	(6)
+#define XLNXSYNC_ISR_PCDONE_MASK	GENMASK(7, 6)
+#define XLNXSYNC_ISR_PCSKIP_MASK	BIT(8)
+#define XLNXSYNC_ISR_PCVALID_MASK	BIT(9)
+/* Consumer related */
+#define XLNXSYNC_ISR_CLDONE_SHIFT	(10)
+#define XLNXSYNC_ISR_CLDONE_MASK	GENMASK(11, 10)
+#define XLNXSYNC_ISR_CLSKIP_MASK	BIT(12)
+#define XLNXSYNC_ISR_CLVALID_MASK	BIT(13)
+#define XLNXSYNC_ISR_CCDONE_SHIFT	(14)
+#define XLNXSYNC_ISR_CCDONE_MASK	GENMASK(15, 14)
+#define XLNXSYNC_ISR_CCSKIP_MASK	BIT(16)
+#define XLNXSYNC_ISR_CCVALID_MASK	BIT(17)
+
+#define XLNXSYNC_ISR_LDIFF		BIT(18)
+#define XLNXSYNC_ISR_CDIFF		BIT(19)
+#define XLNXSYNC_ISR_CONS_SYNC_FAIL_MASK BIT(20)
+#define XLNXSYNC_ISR_CONS_WDG_ERR_MASK	BIT(21)
+
+/* bit 44 of start address */
+#define XLNXSYNC_FB_VALID_MASK		BIT(12)
+#define XLNXSYNC_FB_HI_ADDR_MASK	GENMASK(11, 0)
+
+#define XLNXSYNC_IMR_PROD_SYNC_FAIL_MASK BIT(0)
+#define XLNXSYNC_IMR_PROD_WDG_ERR_MASK	BIT(1)
+/* Producer */
+#define XLNXSYNC_IMR_PLVALID_MASK	BIT(5)
+#define XLNXSYNC_IMR_PCVALID_MASK	BIT(9)
+/* Consumer */
+#define XLNXSYNC_IMR_CLVALID_MASK	BIT(13)
+#define XLNXSYNC_IMR_CCVALID_MASK	BIT(17)
+/* Diff */
+#define XLNXSYNC_IMR_LDIFF		BIT(18)
+#define XLNXSYNC_IMR_CDIFF		BIT(19)
+#define XLNXSYNC_IMR_CONS_SYNC_FAIL_MASK BIT(20)
+#define XLNXSYNC_IMR_CONS_WDG_ERR_MASK	BIT(21)
+
+#define XLNXSYNC_IMR_ALL_MASK		(XLNXSYNC_IMR_PROD_SYNC_FAIL_MASK |\
+					 XLNXSYNC_IMR_PROD_WDG_ERR_MASK |\
+					 XLNXSYNC_IMR_PLVALID_MASK |\
+					 XLNXSYNC_IMR_PCVALID_MASK |\
+					 XLNXSYNC_IMR_CLVALID_MASK |\
+					 XLNXSYNC_IMR_CCVALID_MASK |\
+					 XLNXSYNC_IMR_LDIFF |\
+					 XLNXSYNC_IMR_CDIFF |\
+					 XLNXSYNC_IMR_CONS_SYNC_FAIL_MASK |\
+					 XLNXSYNC_IMR_CONS_WDG_ERR_MASK)
+
+/* Other macros */
+#define XLNXSYNC_CHAN_OFFSET		0x100
+#define XLNXSYNC_BUF_ADDR_SHIFT	0x3
+#define XLNXSYNC_DEVNAME_LEN		(32)
+
+#define XLNXSYNC_DRIVER_NAME		"xlnxsync"
+#define XLNXSYNC_DRIVER_VERSION		"0.1"
+
+#define XLNXSYNC_DEV_MAX		256
+
+/* Module Parameters */
+static struct class *xlnxsync_class;
+static dev_t xlnxsync_devt;
+/* Used to keep track of sync devices */
+static DEFINE_IDA(xs_ida);
+
+/**
+ * struct xlnxsync_device - Xilinx Synchronizer struct
+ * @chdev: Character device driver struct
+ * @dev: Pointer to device
+ * @iomem: Pointer to the register space
+ * @sync_mutex: Serialize general device specific ioctl calls
+ * @axi_clk: Pointer to clock structure for axilite clock
+ * @p_clk: Pointer to clock structure for producer clock
+ * @c_clk: Pointer to clock structure for consumer clock
+ * @user_count: Usage count
+ * @irq: IRQ number
+ * @irq_lock: Spinlock used to protect access to sync and watchdog error
+ * @minor: Device id count
+ * @config: IP config struct
+ * @channels: List head for syncip channel linked list
+ * @chan_count : Active channel number count
+ * @reserved : Bitmap to track reserved channels
+ *
+ * This structure contains the device driver related parameters
+ */
+struct xlnxsync_device {
+	struct cdev chdev;
+	struct device *dev;
+	void __iomem *iomem;
+	/* sync_mutex is used to serialize general device ioctl calls */
+	struct mutex sync_mutex;
+	struct clk *axi_clk;
+	struct clk *p_clk;
+	struct clk *c_clk;
+	atomic_t user_count;
+	unsigned int irq;
+	/* irq_lock is used to protect access to sync_err and wdg_err */
+	spinlock_t irq_lock;
+	u32 minor;
+	struct xlnxsync_config config;
+	struct list_head channels;
+	u8 chan_count;
+	unsigned long reserved;
+};
+
+/**
+ * struct xlnxsync_channel - Synchronizer context struct
+ * @dev: Xilinx synchronizer device struct
+ * @mutex: Serialize channel specific ioctl calls
+ * @id: Channel id
+ * @last_buf_used: Save last buffer id used
+ * @channel: list entry into syncip channel lists
+ * @wq_fbdone: Wait queue for frame buffer done events
+ * @wq_error: Wait queue for error events
+ * @l_done: Luma done result array
+ * @c_done: Chroma done result array
+ * @prod_sync_err: Capture synchronization error per channel
+ * @prod_wdg_err: Capture watchdog error per channel
+ * @cons_sync_err: Consumer synchronization error per channel
+ * @cons_wdg_err: Consumer watchdog error per channel
+ * @ldiff_err: Luma buffer diff > 1
+ * @cdiff_err: Chroma buffer diff > 1
+ * @err_event: Error event per channel
+ * @framedone_event: Framebuffer done event per channel
+ *
+ * This structure contains the syncip channel specific parameters
+ */
+struct xlnxsync_channel {
+	struct xlnxsync_device *dev;
+	/* Serialize channel specific ioctl calls */
+	struct mutex mutex;
+	u32 id;
+	int last_buf_used;
+	struct list_head channel;
+	wait_queue_head_t wq_fbdone;
+	wait_queue_head_t wq_error;
+	u8 l_done[XLNXSYNC_BUF_PER_CHAN][XLNXSYNC_IO];
+	u8 c_done[XLNXSYNC_BUF_PER_CHAN][XLNXSYNC_IO];
+	u8 prod_sync_err : 1;
+	u8 prod_wdg_err : 1;
+	u8 cons_sync_err : 1;
+	u8 cons_wdg_err : 1;
+	u8 ldiff_err : 1;
+	u8 cdiff_err : 1;
+	u8 err_event : 1;
+	u8 framedone_event : 1;
+};
+
+static inline u32 xlnxsync_read(struct xlnxsync_device *dev, u32 chan, u32 reg)
+{
+	return ioread32(dev->iomem + (chan * XLNXSYNC_CHAN_OFFSET) + reg);
+}
+
+static inline void xlnxsync_write(struct xlnxsync_device *dev, u32 chan,
+				  u32 reg, u32 val)
+{
+	iowrite32(val, dev->iomem + (chan * XLNXSYNC_CHAN_OFFSET) + reg);
+}
+
+static inline void xlnxsync_clr(struct xlnxsync_device *dev, u32 chan, u32 reg,
+				u32 clr)
+{
+	xlnxsync_write(dev, chan, reg, xlnxsync_read(dev, chan, reg) & ~clr);
+}
+
+static inline void xlnxsync_set(struct xlnxsync_device *dev, u32 chan, u32 reg,
+				u32 set)
+{
+	xlnxsync_write(dev, chan, reg, xlnxsync_read(dev, chan, reg) | set);
+}
+
+static bool xlnxsync_is_buf_done(struct xlnxsync_device *dev,
+				 u32 channel, u32 buf, u32 io,
+				 u8 force_clr_valid)
+{
+	u32 luma_valid, chroma_valid, reg_laddr, reg_caddr, buf_offset;
+
+	switch (io) {
+	case XLNXSYNC_PROD:
+		reg_laddr = XLNXSYNC_PL_START_HI_REG;
+		reg_caddr = XLNXSYNC_PC_START_HI_REG;
+		break;
+	case XLNXSYNC_CONS:
+		reg_laddr = XLNXSYNC_CL_START_HI_REG;
+		reg_caddr = XLNXSYNC_CC_START_HI_REG;
+		break;
+	default:
+		return false;
+	}
+
+	buf_offset = buf << XLNXSYNC_BUF_ADDR_SHIFT;
+	if (force_clr_valid) {
+		xlnxsync_clr(dev, channel, reg_laddr + buf_offset,
+			     XLNXSYNC_FB_VALID_MASK);
+		xlnxsync_clr(dev, channel, reg_caddr + buf_offset,
+			     XLNXSYNC_FB_VALID_MASK);
+	}
+
+	luma_valid = xlnxsync_read(dev, channel, reg_laddr + buf_offset) &
+				   XLNXSYNC_FB_VALID_MASK;
+	chroma_valid = xlnxsync_read(dev, channel, reg_caddr + buf_offset) &
+				     XLNXSYNC_FB_VALID_MASK;
+	if (!luma_valid && !chroma_valid)
+		return true;
+
+	return false;
+}
+
+static void xlnxsync_reset_chan(struct xlnxsync_device *dev, u32 chan)
+{
+	u8 num_retries = 50;
+
+	xlnxsync_set(dev, chan, XLNXSYNC_CTRL_REG, XLNXSYNC_CTRL_SOFTRESET);
+	/* Wait for a maximum of ~100ms to flush pending transactions */
+	while (num_retries--) {
+		if (!(xlnxsync_read(dev, chan, XLNXSYNC_CTRL_REG) &
+				XLNXSYNC_CTRL_SOFTRESET))
+			break;
+		usleep_range(2000, 2100);
+	}
+}
+
+static void xlnxsync_reset(struct xlnxsync_device *dev)
+{
+	u32 i;
+
+	for (i = 0; i < dev->config.max_channels; i++)
+		xlnxsync_reset_chan(dev, i);
+}
+
+static dma_addr_t xlnxsync_get_phy_addr(struct xlnxsync_device *dev,
+					u32 fd)
+{
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	dma_addr_t phy_addr = 0;
+
+	dbuf = dma_buf_get(fd);
+	if (IS_ERR(dbuf)) {
+		dev_err(dev->dev, "%s : Failed to get dma buf\n", __func__);
+		goto get_phy_addr_err;
+	}
+
+	attach = dma_buf_attach(dbuf, dev->dev);
+	if (IS_ERR(attach)) {
+		dev_err(dev->dev, "%s : Failed to attach buf\n", __func__);
+		goto fail_attach;
+	}
+
+	sgt = dma_buf_map_attachment(attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR(sgt)) {
+		dev_err(dev->dev, "%s : Failed to attach map\n", __func__);
+		goto fail_map;
+	}
+
+	phy_addr = sg_dma_address(sgt->sgl);
+	dma_buf_unmap_attachment(attach, sgt, DMA_BIDIRECTIONAL);
+
+fail_map:
+	dma_buf_detach(dbuf, attach);
+fail_attach:
+	dma_buf_put(dbuf);
+get_phy_addr_err:
+	return phy_addr;
+}
+
+static int xlnxsync_chan_config(struct xlnxsync_channel *channel,
+				void __user *arg)
+{
+	struct xlnxsync_chan_config cfg;
+	int ret, i = 0, j;
+	dma_addr_t phy_start_address;
+	u64 luma_start_address[XLNXSYNC_IO];
+	u64 chroma_start_address[XLNXSYNC_IO];
+	u64 luma_end_address[XLNXSYNC_IO];
+	u64 chroma_end_address[XLNXSYNC_IO];
+	struct xlnxsync_device *dev = channel->dev;
+
+	ret = copy_from_user(&cfg, arg, sizeof(cfg));
+	if (ret) {
+		dev_err(dev->dev, "%s : Failed to copy from user\n", __func__);
+		return ret;
+	}
+
+	if (cfg.hdr_ver != XLNXSYNC_IOCTL_HDR_VER) {
+		dev_err(dev->dev, "%s : ioctl version mismatch\n", __func__);
+		dev_err(dev->dev,
+			"ioctl ver = 0x%llx expected ver = 0x%llx\n",
+			cfg.hdr_ver, (u64)XLNXSYNC_IOCTL_HDR_VER);
+		return -EINVAL;
+	}
+
+	/* Calculate luma/chroma physical addresses */
+	phy_start_address = xlnxsync_get_phy_addr(dev, cfg.dma_fd);
+	if (!phy_start_address) {
+		dev_err(dev->dev, "%s : Failed to obtain physical address\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	luma_start_address[XLNXSYNC_PROD] =
+		cfg.luma_start_offset[XLNXSYNC_PROD] + phy_start_address;
+	luma_start_address[XLNXSYNC_CONS] =
+		cfg.luma_start_offset[XLNXSYNC_CONS] + phy_start_address;
+	chroma_start_address[XLNXSYNC_PROD] =
+		cfg.chroma_start_offset[XLNXSYNC_PROD] + phy_start_address;
+	chroma_start_address[XLNXSYNC_CONS] =
+		cfg. chroma_start_offset[XLNXSYNC_CONS] + phy_start_address;
+	luma_end_address[XLNXSYNC_PROD] =
+		cfg.luma_end_offset[XLNXSYNC_PROD] + phy_start_address;
+	luma_end_address[XLNXSYNC_CONS] =
+		cfg.luma_end_offset[XLNXSYNC_CONS] + phy_start_address;
+	chroma_end_address[XLNXSYNC_PROD] =
+		cfg.chroma_end_offset[XLNXSYNC_PROD] + phy_start_address;
+	chroma_end_address[XLNXSYNC_CONS] =
+		cfg.chroma_end_offset[XLNXSYNC_CONS] + phy_start_address;
+
+	dev_dbg(dev->dev, "Channel id = %d", channel->id);
+	dev_dbg(dev->dev, "Producer address\n");
+	dev_dbg(dev->dev, "Luma Start Addr = 0x%llx End Addr = 0x%llx Margin = 0x%08x\n",
+		luma_start_address[XLNXSYNC_PROD],
+		luma_end_address[XLNXSYNC_PROD], cfg.luma_margin);
+	dev_dbg(dev->dev, "Chroma Start Addr = 0x%llx End Addr = 0x%llx Margin = 0x%08x\n",
+		chroma_start_address[XLNXSYNC_PROD],
+		chroma_end_address[XLNXSYNC_PROD], cfg.chroma_margin);
+	dev_dbg(dev->dev, "FB id = %d IsMono = %d\n",
+		cfg.fb_id[XLNXSYNC_PROD], cfg.ismono[XLNXSYNC_PROD]);
+	dev_dbg(dev->dev, "Consumer address\n");
+	dev_dbg(dev->dev, "Luma Start Addr = 0x%llx End Addr = 0x%llx\n",
+		luma_start_address[XLNXSYNC_CONS],
+		luma_end_address[XLNXSYNC_CONS]);
+	dev_dbg(dev->dev, "Chroma Start Addr = 0x%llx End Addr = 0x%llx\n",
+		chroma_start_address[XLNXSYNC_CONS],
+		chroma_end_address[XLNXSYNC_CONS]);
+	dev_dbg(dev->dev, "FB id = %d IsMono = %d\n",
+		cfg.fb_id[XLNXSYNC_CONS], cfg.ismono[XLNXSYNC_CONS]);
+
+	for (j = 0; j < XLNXSYNC_IO; j++) {
+		u32 l_start_reg, l_end_reg, c_start_reg, c_end_reg;
+
+		if (cfg.fb_id[j] == XLNXSYNC_AUTO_SEARCH) {
+			/*
+			 * When fb_id is 0xFF auto search for free fb
+			 * in a channel
+			 */
+			dev_dbg(dev->dev, "%s : auto search free fb\n",
+				__func__);
+			switch (channel->last_buf_used) {
+			case 0:
+				i = 1;
+				break;
+			case 1:
+				i = 2;
+				break;
+			case 2:
+			case -1:
+			default:
+				i = 0;
+				break;
+			}
+
+			if (xlnxsync_is_buf_done(dev, channel->id, i, j, false)) {
+				dev_dbg(dev->dev,
+					"Channel %d %s FB %d is assigned\n",
+					channel->id, j ? "cons" : "prod", i);
+				if (j)
+					channel->last_buf_used = i;
+			} else {
+				dev_dbg(dev->dev,
+					"Channel %d %s FB %d is busy\n",
+					channel->id, j ? "cons" : "prod", i);
+				if (j) {
+					/* Force clear producer buf valid */
+					if (!xlnxsync_is_buf_done(dev,
+								  channel->id,
+								  i, 0, true)) {
+						dev_err(dev->dev,
+							"prod:buffer valid:\t"
+							"resetting failed\n");
+					}
+				}
+				return -EBUSY;
+			}
+		} else if (cfg.fb_id[j] >= 0 &&
+			   cfg.fb_id[j] < XLNXSYNC_BUF_PER_CHAN) {
+			/* If fb_id is specified, check its availability */
+			if (!(xlnxsync_is_buf_done(dev, channel->id,
+						   cfg.fb_id[j], j, false))) {
+				dev_dbg(dev->dev,
+					"%s : %s FB %d in channel %d is busy!\n",
+					__func__, j ? "prod" : "cons",
+					i, channel->id);
+				return -EBUSY;
+			}
+			dev_dbg(dev->dev, "%s : Configure fb %d\n",
+				__func__, i);
+		} else {
+			/* Invalid fb_id passed */
+			dev_err(dev->dev, "Invalid FB id %d for configuration!\n",
+				cfg.fb_id[j]);
+			return -EINVAL;
+		}
+
+		if (j == XLNXSYNC_PROD) {
+			l_start_reg = XLNXSYNC_PL_START_LO_REG;
+			l_end_reg = XLNXSYNC_PL_END_LO_REG;
+			c_start_reg = XLNXSYNC_PC_START_LO_REG;
+			c_end_reg = XLNXSYNC_PC_END_LO_REG;
+		} else {
+			l_start_reg = XLNXSYNC_CL_START_LO_REG;
+			l_end_reg = XLNXSYNC_CL_END_LO_REG;
+			c_start_reg = XLNXSYNC_CC_START_LO_REG;
+			c_end_reg = XLNXSYNC_CC_END_LO_REG;
+		}
+
+		/* Start Address */
+		xlnxsync_write(dev, channel->id, l_start_reg + (i << 3),
+			       lower_32_bits(luma_start_address[j]));
+
+		xlnxsync_write(dev, channel->id,
+			       (l_start_reg + 4) + (i << 3),
+			       upper_32_bits(luma_start_address[j]) &
+			       XLNXSYNC_FB_HI_ADDR_MASK);
+
+		/* End Address */
+		xlnxsync_write(dev, channel->id, l_end_reg + (i << 3),
+			       lower_32_bits(luma_end_address[j]));
+		xlnxsync_write(dev, channel->id, l_end_reg + 4 + (i << 3),
+			       upper_32_bits(luma_end_address[j]));
+
+		/* Set margin */
+		xlnxsync_write(dev, channel->id,
+			       XLNXSYNC_L_MARGIN_REG + (i << 2),
+			       cfg.luma_margin);
+
+		if (!cfg.ismono[j]) {
+			dev_dbg(dev->dev, "%s : Not monochrome. Program Chroma\n",
+				__func__);
+
+			/* Chroma Start Address */
+			xlnxsync_write(dev, channel->id,
+				       c_start_reg + (i << 3),
+				       lower_32_bits(chroma_start_address[j]));
+
+			xlnxsync_write(dev, channel->id,
+				       c_start_reg + 4 + (i << 3),
+				       upper_32_bits(chroma_start_address[j]) &
+				       XLNXSYNC_FB_HI_ADDR_MASK);
+
+			/* Chroma End Address */
+			xlnxsync_write(dev, channel->id,
+				       c_end_reg + (i << 3),
+				       lower_32_bits(chroma_end_address[j]));
+
+			xlnxsync_write(dev, channel->id,
+				       c_end_reg + 4 + (i << 3),
+				       upper_32_bits(chroma_end_address[j]));
+
+			/* Chroma Margin */
+			xlnxsync_write(dev, channel->id,
+				       XLNXSYNC_C_MARGIN_REG + (i << 2),
+				       cfg.chroma_margin);
+
+			/* Set the Valid bit */
+			xlnxsync_set(dev, channel->id,
+				     c_start_reg + 4 + (i << 3),
+				     XLNXSYNC_FB_VALID_MASK);
+		}
+
+		/* Set the Valid bit */
+		xlnxsync_set(dev, channel->id, l_start_reg + 4 + (i << 3),
+			     XLNXSYNC_FB_VALID_MASK);
+	}
+
+	for (i = 0; i < XLNXSYNC_MAX_CORES; i++) {
+		iowrite32(cfg.luma_core_offset[i],
+			  dev->iomem + XLNXSYNC_LCOREOFF_REG +
+			  (i * XLNXSYNC_COREOFF_NEXT));
+
+		iowrite32(cfg.chroma_core_offset[i],
+			  dev->iomem + XLNXSYNC_CCOREOFF_REG +
+			  (i * XLNXSYNC_COREOFF_NEXT));
+	}
+
+	return 0;
+}
+
+static int xlnxsync_chan_get_status(struct xlnxsync_channel *channel,
+				    void __user *arg)
+{
+	int ret;
+	u32 i, j;
+	unsigned long flags;
+	struct xlnxsync_stat status;
+	struct xlnxsync_device *dev = channel->dev;
+
+	/* Update Buffers status */
+	for (i = 0; i < XLNXSYNC_BUF_PER_CHAN; i++) {
+		for (j = 0; j < XLNXSYNC_IO; j++) {
+			if (xlnxsync_is_buf_done(dev, channel->id, i, j, false))
+				status.fbdone[i][j] = true;
+			else
+				status.fbdone[i][j] = false;
+		}
+	}
+
+	/* Update channel enable status */
+	if (xlnxsync_read(dev, channel->id, XLNXSYNC_CTRL_REG) &
+	    XLNXSYNC_CTRL_ENABLE_MASK)
+		status.enable = true;
+
+	/* Update channel error status */
+	spin_lock_irqsave(&dev->irq_lock, flags);
+	status.err.prod_sync = channel->prod_sync_err;
+	status.err.prod_wdg = channel->prod_wdg_err;
+	status.err.cons_sync = channel->cons_sync_err;
+	status.err.cons_wdg = channel->cons_wdg_err;
+	status.err.ldiff = channel->ldiff_err;
+	status.err.cdiff = channel->cdiff_err;
+	spin_unlock_irqrestore(&dev->irq_lock, flags);
+
+	status.hdr_ver = XLNXSYNC_IOCTL_HDR_VER;
+
+	ret = copy_to_user(arg, &status, sizeof(status));
+	if (ret) {
+		dev_err(dev->dev, "%s: failed to copy result data to user\n",
+			__func__);
+	} else {
+		channel->prod_sync_err = 0;
+		channel->prod_wdg_err = 0;
+		channel->cons_sync_err = 0;
+		channel->cons_wdg_err = 0;
+		channel->ldiff_err = 0;
+		channel->cdiff_err = 0;
+	}
+
+	return ret;
+}
+
+static int xlnxsync_reset_slot(struct xlnxsync_channel *channel)
+{
+	struct xlnxsync_device *dev = channel->dev;
+	int slot;
+
+	if (dev->config.hdr_ver != XLNXSYNC_IOCTL_HDR_VER) {
+		dev_err(dev->dev, "ioctl not supported!\n");
+		return -EINVAL;
+	}
+
+	/* check channel v/s max from dt */
+	if (channel->id >= dev->config.max_channels) {
+		dev_err(dev->dev, "Invalid channel %d. Max channels = %d!\n",
+			channel->id, dev->config.max_channels);
+		return -EINVAL;
+	}
+
+	slot = channel->last_buf_used + 1;
+	if (slot == XLNXSYNC_BUF_PER_CHAN)
+		slot = 0;
+
+	xlnxsync_write(dev, channel->id,
+		       XLNXSYNC_CL_START_LO_REG + 4 + (slot << 3), 0);
+	xlnxsync_write(dev, channel->id,
+		       XLNXSYNC_CC_START_LO_REG + 4 + (slot << 3), 0);
+	xlnxsync_write(dev, channel->id,
+		       XLNXSYNC_PL_START_LO_REG + 4 + (slot << 3), 0);
+	xlnxsync_write(dev, channel->id,
+		       XLNXSYNC_PC_START_LO_REG + 4 + (slot << 3), 0);
+
+	return 0;
+}
+
+static int xlnxsync_chan_enable(struct xlnxsync_channel *channel, bool enable)
+{
+	struct xlnxsync_device *dev = channel->dev;
+	unsigned int i, j;
+
+	if (dev->config.hdr_ver != XLNXSYNC_IOCTL_HDR_VER) {
+		dev_err(dev->dev, "ioctl not supported!\n");
+		return -EINVAL;
+	}
+
+	/* check channel v/s max from dt */
+	if (channel->id >= dev->config.max_channels) {
+		dev_err(dev->dev, "Invalid channel %d. Max channels = %d!\n",
+			channel->id, dev->config.max_channels);
+		return -EINVAL;
+	}
+
+	if (enable) {
+		dev_dbg(dev->dev, "Enabling %d channel\n", channel->id);
+		xlnxsync_set(dev, channel->id, XLNXSYNC_CTRL_REG,
+			     XLNXSYNC_CTRL_ENABLE_MASK |
+			     XLNXSYNC_CTRL_INTR_EN_MASK);
+	} else {
+		dev_dbg(dev->dev, "Disabling %d channel\n", channel->id);
+		xlnxsync_reset_chan(dev, channel->id);
+		xlnxsync_clr(dev, channel->id, XLNXSYNC_CTRL_REG,
+			     XLNXSYNC_CTRL_ENABLE_MASK |
+			     XLNXSYNC_CTRL_INTR_EN_MASK);
+		channel->prod_sync_err = false;
+		channel->prod_wdg_err = false;
+		channel->cons_sync_err = false;
+		channel->cons_wdg_err = false;
+		channel->ldiff_err = false;
+		channel->cdiff_err = false;
+
+		for (i = 0; i < XLNXSYNC_BUF_PER_CHAN; i++) {
+			for (j = 0; j < XLNXSYNC_IO; j++) {
+				channel->l_done[i][j] = false;
+				channel->c_done[i][j] = false;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int xlnxsync_get_config(struct xlnxsync_channel *channel,
+			       void __user *arg)
+{
+	struct xlnxsync_config cfg;
+	int ret;
+	struct xlnxsync_device *dev = channel->dev;
+
+	cfg.encode = dev->config.encode;
+	cfg.max_channels = dev->config.max_channels;
+	cfg.active_channels = dev->chan_count;
+	cfg.hdr_ver = XLNXSYNC_IOCTL_HDR_VER;
+	cfg.reserved_id = channel->id;
+	dev_dbg(dev->dev, "IP Config : encode = %d max_channels = %d\n",
+		cfg.encode, cfg.max_channels);
+	dev_dbg(dev->dev, "IP Config : active channels = %d reserved id = %d\n",
+		cfg.active_channels, cfg.reserved_id);
+	dev_dbg(dev->dev, "ioctl version = 0x%llx\n", cfg.hdr_ver);
+	ret = copy_to_user(arg, &cfg, sizeof(cfg));
+	if (ret) {
+		dev_err(dev->dev, "%s: failed to copy result data to user\n",
+			__func__);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xlnxsync_chan_clr_err(struct xlnxsync_channel *channel,
+				 void __user *arg)
+{
+	struct xlnxsync_clr_err errcfg;
+	u32 intr_unmask_val = 0;
+	int ret;
+	unsigned long flags;
+	struct xlnxsync_device *dev = channel->dev;
+
+	ret = copy_from_user(&errcfg, arg, sizeof(errcfg));
+	if (ret) {
+		dev_err(dev->dev, "%s : Failed to copy from user\n", __func__);
+		return ret;
+	}
+
+	if (errcfg.hdr_ver != XLNXSYNC_IOCTL_HDR_VER) {
+		dev_err(dev->dev, "%s : ioctl version mismatch\n", __func__);
+		dev_err(dev->dev,
+			"ioctl ver = 0x%llx expected ver = 0x%llx\n",
+			errcfg.hdr_ver, (u64)XLNXSYNC_IOCTL_HDR_VER);
+		return -EINVAL;
+	}
+
+	dev_dbg(dev->dev, "%s : Clearing %d channel errors\n",
+		__func__, channel->id);
+	/* Clear channel error status */
+	spin_lock_irqsave(&dev->irq_lock, flags);
+	if (errcfg.err.prod_sync) {
+		dev_dbg(dev->dev, "Unmasking producer sync err\n");
+		intr_unmask_val |= XLNXSYNC_IMR_PROD_SYNC_FAIL_MASK;
+	}
+
+	if (errcfg.err.prod_wdg) {
+		dev_dbg(dev->dev, "Unmasking producer wdg err\n");
+		intr_unmask_val |= XLNXSYNC_IMR_PROD_WDG_ERR_MASK;
+	}
+
+	if (errcfg.err.cons_sync) {
+		dev_dbg(dev->dev, "Unmasking consumer sync err\n");
+		intr_unmask_val |= XLNXSYNC_IMR_CONS_SYNC_FAIL_MASK;
+	}
+
+	if (errcfg.err.cons_wdg) {
+		dev_dbg(dev->dev, "Unmasking consumer wdg err\n");
+		intr_unmask_val |= XLNXSYNC_IMR_CONS_WDG_ERR_MASK;
+	}
+
+	if (errcfg.err.ldiff) {
+		dev_dbg(dev->dev, "Unmasking ldiff_err err\n");
+		intr_unmask_val |= XLNXSYNC_IMR_LDIFF;
+	}
+
+	if (errcfg.err.cdiff) {
+		dev_dbg(dev->dev, "Unmasking cdiff_err err\n");
+		intr_unmask_val |= XLNXSYNC_IMR_CDIFF;
+	}
+
+	xlnxsync_clr(dev, channel->id, XLNXSYNC_IMR_REG, intr_unmask_val);
+
+	dev_dbg(dev->dev, "Channel num:%d IMR: %x\n", channel->id,
+		xlnxsync_read(dev, channel->id, XLNXSYNC_IMR_REG));
+
+	spin_unlock_irqrestore(&dev->irq_lock, flags);
+
+	return 0;
+}
+
+static int xlnxsync_chan_get_fbdone_status(struct xlnxsync_channel *channel,
+					   void __user *arg)
+{
+	struct xlnxsync_fbdone fbdone_stat;
+	int ret, i, j;
+	struct xlnxsync_device *dev = channel->dev;
+
+	fbdone_stat.hdr_ver = XLNXSYNC_IOCTL_HDR_VER;
+
+	for (i = 0; i < XLNXSYNC_BUF_PER_CHAN; i++)
+		for (j = 0; j < XLNXSYNC_IO; j++)
+			if (channel->l_done[i][j] &&
+			    channel->c_done[i][j])
+				fbdone_stat.status[i][j] = true;
+
+	ret = copy_to_user(arg, &fbdone_stat, sizeof(fbdone_stat));
+	if (ret)
+		dev_err(dev->dev, "%s: failed to copy result data to user\n",
+			__func__);
+
+	return ret;
+}
+
+static int xlnxsync_chan_clr_fbdone_status(struct xlnxsync_channel *channel,
+					   void __user *arg)
+{
+	struct xlnxsync_fbdone fbd;
+	int ret, i, j;
+	unsigned long flags;
+	struct xlnxsync_device *dev = channel->dev;
+
+	ret = copy_from_user(&fbd, arg, sizeof(fbd));
+	if (ret) {
+		dev_err(dev->dev, "%s : Failed to copy from user\n", __func__);
+		return ret;
+	}
+
+	if (fbd.hdr_ver != XLNXSYNC_IOCTL_HDR_VER) {
+		dev_err(dev->dev, "%s : ioctl version mismatch\n", __func__);
+		dev_err(dev->dev,
+			"ioctl ver = 0x%llx expected ver = 0x%llx\n",
+			fbd.hdr_ver, (u64)XLNXSYNC_IOCTL_HDR_VER);
+		return -EINVAL;
+	}
+
+	/* Clear channel error status */
+	spin_lock_irqsave(&dev->irq_lock, flags);
+	for (i = 0; i < XLNXSYNC_BUF_PER_CHAN; i++) {
+		for (j = 0; j < XLNXSYNC_IO; j++) {
+			fbd.status[i][j] = false;
+			channel->l_done[i][j] = false;
+			channel->c_done[i][j] = false;
+		}
+	}
+	spin_unlock_irqrestore(&dev->irq_lock, flags);
+
+	return 0;
+}
+
+static int xlnxsync_chan_set_int_mask(struct xlnxsync_channel *channel,
+				      void __user *arg)
+{
+	struct xlnxsync_device *dev = channel->dev;
+	struct xlnxsync_intr intr_mask;
+	u32 intr_mask_val = 0;
+	int ret;
+
+	ret = copy_from_user(&intr_mask, arg, sizeof(intr_mask));
+	if (ret) {
+		dev_err(dev->dev, "%s : Failed to copy from user\n", __func__);
+		return ret;
+	}
+
+	/* check driver header version */
+	if (intr_mask.hdr_ver != XLNXSYNC_IOCTL_HDR_VER) {
+		dev_err(dev->dev, "%s : ioctl version mismatch\n", __func__);
+		dev_err(dev->dev,
+			"ioctl ver = 0x%llx expected ver = 0x%llx\n",
+			intr_mask.hdr_ver, (u64)XLNXSYNC_IOCTL_HDR_VER);
+		return -EINVAL;
+	}
+
+	if (intr_mask.err.prod_sync)
+		intr_mask_val |= XLNXSYNC_IMR_PROD_SYNC_FAIL_MASK;
+	if (intr_mask.err.prod_wdg)
+		intr_mask_val |= XLNXSYNC_IMR_PROD_WDG_ERR_MASK;
+	if (intr_mask.err.cons_sync)
+		intr_mask_val |= XLNXSYNC_IMR_CONS_SYNC_FAIL_MASK;
+	if (intr_mask.err.cons_wdg)
+		intr_mask_val |= XLNXSYNC_IMR_CONS_WDG_ERR_MASK;
+	if (intr_mask.err.ldiff)
+		intr_mask_val |= XLNXSYNC_IMR_LDIFF;
+	if (intr_mask.err.cdiff)
+		intr_mask_val |= XLNXSYNC_IMR_CDIFF;
+	if (intr_mask.prod_lfbdone)
+		intr_mask_val |= XLNXSYNC_IMR_PLVALID_MASK;
+	if (intr_mask.prod_cfbdone)
+		intr_mask_val |= XLNXSYNC_IMR_PCVALID_MASK;
+	if (intr_mask.cons_lfbdone)
+		intr_mask_val |= XLNXSYNC_IMR_CLVALID_MASK;
+	if (intr_mask.cons_cfbdone)
+		intr_mask_val |= XLNXSYNC_IMR_CCVALID_MASK;
+
+	dev_dbg(dev->dev, "Set interrupt mask: 0x%x for channel: %d\n",
+		intr_mask_val, channel->id);
+
+	xlnxsync_write(dev, channel->id, XLNXSYNC_IMR_REG, intr_mask_val);
+
+	return ret;
+}
+
+static long xlnxsync_ioctl(struct file *fptr, unsigned int cmd,
+			   unsigned long data)
+{
+	int ret = -EINVAL;
+	void __user *arg = (void __user *)data;
+	struct xlnxsync_channel *channel = fptr->private_data;
+	struct xlnxsync_device *xlnxsync_dev;
+
+	xlnxsync_dev = channel->dev;
+	if (!xlnxsync_dev) {
+		pr_err("%s: File op error\n", __func__);
+		return -EIO;
+	}
+
+	dev_dbg(xlnxsync_dev->dev, "ioctl = 0x%08x\n", cmd);
+
+	switch (cmd) {
+	case XLNXSYNC_GET_CFG:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_get_config(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_GET_STATUS:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_get_status(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_SET_CONFIG:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_config(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_ENABLE:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_enable(channel, true);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_DISABLE:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_enable(channel, false);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_CLR_ERR:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_clr_err(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_GET_FBDONE_STAT:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_get_fbdone_status(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_CLR_FBDONE_STAT:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_clr_fbdone_status(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_CHAN_SET_INTR_MASK:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_chan_set_int_mask(channel, arg);
+		mutex_unlock(&channel->mutex);
+		break;
+	case XLNXSYNC_RESET_SLOT:
+		if (mutex_lock_interruptible(&channel->mutex))
+			return -ERESTARTSYS;
+		ret = xlnxsync_reset_slot(channel);
+		mutex_unlock(&channel->mutex);
+		break;
+	}
+
+	return ret;
+}
+
+static __poll_t xlnxsync_poll(struct file *fptr, poll_table *wait)
+{
+	__poll_t ret = 0, req_events = poll_requested_events(wait);
+	struct xlnxsync_channel *channel = fptr->private_data;
+	struct xlnxsync_device *dev;
+	unsigned long flags;
+
+	dev = channel->dev;
+	if (!dev) {
+		pr_err("%s: File op error\n", __func__);
+		return -EIO;
+	}
+
+	dev_dbg_ratelimited(dev->dev, "%s : entered req_events = 0x%x!\n",
+			    __func__, req_events);
+
+	if (!(req_events & (POLLPRI | POLLIN)))
+		return 0;
+
+	if (req_events & EPOLLPRI) {
+		poll_wait(fptr, &channel->wq_error, wait);
+		spin_lock_irqsave(&dev->irq_lock, flags);
+		if (channel->err_event) {
+			dev_dbg_ratelimited(dev->dev,
+					    "%s : error event in chan = %d!\n",
+					     __func__, channel->id);
+			ret |= POLLPRI;
+			channel->err_event = false;
+		}
+		spin_unlock_irqrestore(&dev->irq_lock, flags);
+	}
+
+	if (req_events & EPOLLIN) {
+		poll_wait(fptr, &channel->wq_fbdone, wait);
+		spin_lock_irqsave(&dev->irq_lock, flags);
+		if (channel->framedone_event) {
+			dev_dbg_ratelimited(dev->dev,
+					    "%s : fbdone event in chan = %d!\n",
+					    __func__, channel->id);
+			ret |= POLLIN;
+			channel->framedone_event = false;
+		}
+		spin_unlock_irqrestore(&dev->irq_lock, flags);
+	}
+
+	return ret;
+}
+
+static int xlnxsync_open(struct inode *iptr, struct file *fptr)
+{
+	struct xlnxsync_device *dev;
+	struct xlnxsync_channel *chan;
+	unsigned int i;
+
+	dev = container_of(iptr->i_cdev, struct xlnxsync_device, chdev);
+	if (!dev) {
+		pr_err("%s: failed to get xlnxsync driver handle\n", __func__);
+		return -EAGAIN;
+	}
+
+	chan = devm_kzalloc(dev->dev, sizeof(*chan), GFP_KERNEL);
+	if (!chan)
+		return -ENOMEM;
+
+	if (mutex_lock_interruptible(&dev->sync_mutex))
+		return -ERESTARTSYS;
+	i = find_first_zero_bit_le(&dev->reserved, dev->config.max_channels);
+	if (i >= dev->config.max_channels) {
+		dev_err(dev->dev, "No free channel available\n");
+		mutex_unlock(&dev->sync_mutex);
+		return -ENOSPC;
+	}
+	dev_dbg(dev->dev, "Reserving channel %d\n", i);
+	set_bit(i, &dev->reserved);
+	chan->id = i;
+	chan->last_buf_used = -1;
+	list_add_tail(&chan->channel, &dev->channels);
+	chan->dev = dev;
+	fptr->private_data = chan;
+	mutex_init(&chan->mutex);
+	init_waitqueue_head(&chan->wq_fbdone);
+	init_waitqueue_head(&chan->wq_error);
+	dev->chan_count++;
+	atomic_inc(&dev->user_count);
+	dev_dbg(dev->dev, "%s: tid=%d Opened with user count = %d\n",
+		__func__, current->pid, atomic_read(&dev->user_count));
+	mutex_unlock(&dev->sync_mutex);
+
+	return 0;
+}
+
+static int xlnxsync_release(struct inode *iptr, struct file *fptr)
+{
+	struct xlnxsync_device *dev;
+	struct xlnxsync_channel *channel = fptr->private_data;
+
+	dev = container_of(iptr->i_cdev, struct xlnxsync_device, chdev);
+	if (!dev) {
+		pr_err("%s: failed to get xlnxsync driver handle", __func__);
+		return -EAGAIN;
+	}
+
+	dev_dbg(dev->dev, "%s: tid=%d user count = %d id = %d\n",
+		__func__, current->pid, atomic_read(&dev->user_count),
+		channel->id);
+
+	if (xlnxsync_read(dev, channel->id, XLNXSYNC_CTRL_REG) &
+			XLNXSYNC_CTRL_ENABLE_MASK) {
+		dev_dbg(dev->dev, "Disabling %d channel\n", channel->id);
+		xlnxsync_reset_chan(dev, channel->id);
+		xlnxsync_clr(dev, channel->id, XLNXSYNC_CTRL_REG,
+			     XLNXSYNC_CTRL_ENABLE_MASK |
+			     XLNXSYNC_CTRL_INTR_EN_MASK);
+	}
+
+	if (mutex_lock_interruptible(&dev->sync_mutex))
+		return -ERESTARTSYS;
+	clear_bit(channel->id, &dev->reserved);
+	dev->chan_count--;
+	list_del(&channel->channel);
+	mutex_unlock(&dev->sync_mutex);
+	devm_kfree(dev->dev, channel);
+
+	if (atomic_dec_and_test(&dev->user_count)) {
+		xlnxsync_reset(dev);
+		dev_dbg(dev->dev,
+			"%s: tid=%d Stopping and clearing device",
+			__func__, current->pid);
+	}
+
+	return 0;
+}
+
+static const struct file_operations xlnxsync_fops = {
+	.open = xlnxsync_open,
+	.release = xlnxsync_release,
+	.unlocked_ioctl = xlnxsync_ioctl,
+	.poll = xlnxsync_poll,
+};
+
+static irqreturn_t xlnxsync_irq_handler(int irq, void *data)
+{
+	struct xlnxsync_device *xlnxsync = (struct xlnxsync_device *)data;
+	u32 val;
+	u32 intr_mask_val = 0;
+	struct xlnxsync_channel *chan;
+
+	/*
+	 * Use simple spin_lock (instead of spin_lock_irqsave) as interrupt
+	 * is registered with irqf_oneshot and !irqf_shared
+	 */
+	spin_lock(&xlnxsync->irq_lock);
+	list_for_each_entry(chan, &xlnxsync->channels, channel) {
+		u32 i, j;
+
+		val = xlnxsync_read(xlnxsync, chan->id, XLNXSYNC_ISR_REG);
+
+		if (val & XLNXSYNC_ISR_PROD_SYNC_FAIL_MASK) {
+			chan->prod_sync_err = true;
+			intr_mask_val |= XLNXSYNC_IMR_PROD_SYNC_FAIL_MASK;
+		}
+		if (val & XLNXSYNC_ISR_PROD_WDG_ERR_MASK) {
+			chan->prod_wdg_err = true;
+			intr_mask_val |= XLNXSYNC_IMR_PROD_WDG_ERR_MASK;
+		}
+		if (val & XLNXSYNC_ISR_LDIFF) {
+			chan->ldiff_err = true;
+			intr_mask_val |= XLNXSYNC_IMR_LDIFF;
+		}
+		if (val & XLNXSYNC_ISR_CDIFF) {
+			chan->cdiff_err = true;
+			intr_mask_val |= XLNXSYNC_IMR_CDIFF;
+		}
+		if (val & XLNXSYNC_ISR_CONS_SYNC_FAIL_MASK) {
+			chan->cons_sync_err = true;
+			intr_mask_val |= XLNXSYNC_IMR_CONS_SYNC_FAIL_MASK;
+		}
+		if (val & XLNXSYNC_ISR_CONS_WDG_ERR_MASK) {
+			chan->cons_wdg_err = true;
+			intr_mask_val |= XLNXSYNC_IMR_CONS_WDG_ERR_MASK;
+		}
+		if (chan->prod_sync_err || chan->prod_wdg_err ||
+		    chan->ldiff_err || chan->cdiff_err ||
+		    chan->cons_sync_err || chan->cons_wdg_err)
+			chan->err_event = true;
+
+		if (val & XLNXSYNC_ISR_PLVALID_MASK) {
+			i = (val & XLNXSYNC_ISR_PLDONE_MASK) >>
+				XLNXSYNC_ISR_PLDONE_SHIFT;
+
+			chan->l_done[i][XLNXSYNC_PROD] = true;
+		}
+
+		if (val & XLNXSYNC_ISR_PCVALID_MASK) {
+			i = (val & XLNXSYNC_ISR_PCDONE_MASK) >>
+				XLNXSYNC_ISR_PCDONE_SHIFT;
+
+			chan->c_done[i][XLNXSYNC_PROD] = true;
+		}
+
+		if (val & XLNXSYNC_ISR_CLVALID_MASK) {
+			i = (val & XLNXSYNC_ISR_CLDONE_MASK) >>
+				XLNXSYNC_ISR_CLDONE_SHIFT;
+
+			chan->l_done[i][XLNXSYNC_CONS] = true;
+		}
+
+		if (val & XLNXSYNC_ISR_CCVALID_MASK) {
+			i = (val & XLNXSYNC_ISR_CCDONE_MASK) >>
+				XLNXSYNC_ISR_CCDONE_SHIFT;
+
+			chan->c_done[i][XLNXSYNC_CONS] = true;
+		}
+
+		for (i = 0; i < XLNXSYNC_BUF_PER_CHAN; i++) {
+			for (j = 0; j < XLNXSYNC_IO; j++) {
+				if (chan->l_done[i][j] &&
+				    chan->c_done[i][j])
+					chan->framedone_event = true;
+			}
+		}
+
+		/* Mask corresponding interrupts */
+		if (intr_mask_val)
+			xlnxsync_set(xlnxsync, chan->id, XLNXSYNC_IMR_REG,
+				     intr_mask_val);
+
+		if (chan->err_event) {
+			dev_dbg(xlnxsync->dev, "%s : error occurred at channel->id = %d\n",
+				__func__, chan->id);
+			wake_up_interruptible(&chan->wq_error);
+		}
+
+		if (chan->framedone_event) {
+			dev_dbg_ratelimited(xlnxsync->dev, "%s : framedone occurred\n",
+					    __func__);
+			wake_up_interruptible(&chan->wq_fbdone);
+		}
+
+	}
+
+	spin_unlock(&xlnxsync->irq_lock);
+
+	return IRQ_HANDLED;
+}
+
+static int xlnxsync_parse_dt_prop(struct xlnxsync_device *xlnxsync)
+{
+	struct device_node *node = xlnxsync->dev->of_node;
+	int ret;
+
+	xlnxsync->config.encode = of_property_read_bool(node, "xlnx,encode");
+	dev_dbg(xlnxsync->dev, "synchronizer type = %s\n",
+		xlnxsync->config.encode ? "encode" : "decode");
+
+	ret = of_property_read_u32(node, "xlnx,num-chan",
+				   (u32 *)&xlnxsync->config.max_channels);
+	if (ret)
+		return ret;
+
+	dev_dbg(xlnxsync->dev, "max channels = %d\n",
+		xlnxsync->config.max_channels);
+
+	if (xlnxsync->config.max_channels == 0 ||
+	    xlnxsync->config.max_channels > XLNXSYNC_MAX_ENC_CHAN) {
+		dev_err(xlnxsync->dev, "Number of channels should be 1 to 4.\n");
+		dev_err(xlnxsync->dev, "Invalid number of channels : %d\n",
+			xlnxsync->config.max_channels);
+		return -EINVAL;
+	}
+
+	if (!xlnxsync->config.encode &&
+	    xlnxsync->config.max_channels > XLNXSYNC_MAX_DEC_CHAN) {
+		dev_err(xlnxsync->dev, "Decode can't have more than 2 channels.\n");
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static int xlnxsync_clk_setup(struct xlnxsync_device *xlnxsync)
+{
+	int ret;
+
+	xlnxsync->axi_clk = devm_clk_get(xlnxsync->dev, "s_axi_ctrl_aclk");
+	if (IS_ERR(xlnxsync->axi_clk)) {
+		ret = PTR_ERR(xlnxsync->axi_clk);
+		dev_err(xlnxsync->dev, "failed to get axi_aclk (%d)\n", ret);
+		return ret;
+	}
+
+	xlnxsync->p_clk = devm_clk_get(xlnxsync->dev, "s_axi_mm_p_aclk");
+	if (IS_ERR(xlnxsync->p_clk)) {
+		ret = PTR_ERR(xlnxsync->p_clk);
+		dev_err(xlnxsync->dev, "failed to get p_aclk (%d)\n", ret);
+		return ret;
+	}
+
+	xlnxsync->c_clk = devm_clk_get(xlnxsync->dev, "s_axi_mm_aclk");
+	if (IS_ERR(xlnxsync->c_clk)) {
+		ret = PTR_ERR(xlnxsync->c_clk);
+		dev_err(xlnxsync->dev, "failed to get axi_mm (%d)\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xlnxsync->axi_clk);
+	if (ret) {
+		dev_err(xlnxsync->dev, "failed to enable axi_clk (%d)\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xlnxsync->p_clk);
+	if (ret) {
+		dev_err(xlnxsync->dev, "failed to enable p_clk (%d)\n", ret);
+		goto err_pclk;
+	}
+
+	ret = clk_prepare_enable(xlnxsync->c_clk);
+	if (ret) {
+		dev_err(xlnxsync->dev, "failed to enable axi_mm (%d)\n", ret);
+		goto err_cclk;
+	}
+
+	return ret;
+
+err_cclk:
+	clk_disable_unprepare(xlnxsync->p_clk);
+err_pclk:
+	clk_disable_unprepare(xlnxsync->axi_clk);
+
+	return ret;
+}
+
+static int xlnxsync_probe(struct platform_device *pdev)
+{
+	struct xlnxsync_device *xlnxsync;
+	struct device *dc;
+	struct resource *res;
+	int ret;
+
+	xlnxsync = devm_kzalloc(&pdev->dev, sizeof(*xlnxsync), GFP_KERNEL);
+	if (!xlnxsync)
+		return -ENOMEM;
+
+	xlnxsync->minor = ida_simple_get(&xs_ida, 0, XLNXSYNC_DEV_MAX,
+					 GFP_KERNEL);
+	if (xlnxsync->minor < 0)
+		return xlnxsync->minor;
+
+	xlnxsync->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "Failed to get resource.\n");
+		return -ENODEV;
+	}
+
+	xlnxsync->iomem = devm_ioremap(xlnxsync->dev, res->start,
+				       resource_size(res));
+	if (!xlnxsync->iomem) {
+		dev_err(&pdev->dev, "ip register mapping failed.\n");
+		return -ENOMEM;
+	}
+
+	ret = xlnxsync_parse_dt_prop(xlnxsync);
+	if (ret < 0)
+		return ret;
+
+	xlnxsync->config.hdr_ver = XLNXSYNC_IOCTL_HDR_VER;
+	dev_dbg(xlnxsync->dev, "ioctl header version = 0x%llx\n",
+		xlnxsync->config.hdr_ver);
+
+	xlnxsync->irq = irq_of_parse_and_map(xlnxsync->dev->of_node, 0);
+	if (!xlnxsync->irq) {
+		dev_err(xlnxsync->dev, "Unable to parse and get irq.\n");
+		return -EINVAL;
+	}
+	ret = devm_request_threaded_irq(xlnxsync->dev, xlnxsync->irq, NULL,
+					xlnxsync_irq_handler,
+					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
+					dev_name(xlnxsync->dev), xlnxsync);
+
+	if (ret) {
+		dev_err(xlnxsync->dev, "Err = %d Interrupt handler reg failed!\n",
+			ret);
+		return ret;
+	}
+
+	ret = xlnxsync_clk_setup(xlnxsync);
+	if (ret) {
+		dev_err(xlnxsync->dev, "clock setup failed!\n");
+		return ret;
+	}
+
+	INIT_LIST_HEAD(&xlnxsync->channels);
+	spin_lock_init(&xlnxsync->irq_lock);
+
+	mutex_init(&xlnxsync->sync_mutex);
+
+	cdev_init(&xlnxsync->chdev, &xlnxsync_fops);
+	xlnxsync->chdev.owner = THIS_MODULE;
+	ret = cdev_add(&xlnxsync->chdev,
+		       MKDEV(MAJOR(xlnxsync_devt), xlnxsync->minor), 1);
+	if (ret < 0) {
+		dev_err(xlnxsync->dev, "cdev_add failed");
+		goto clk_err;
+	}
+
+	if (!xlnxsync_class) {
+		dev_err(xlnxsync->dev, "xvfsync device class not created");
+		goto cdev_err;
+	}
+	dc = device_create(xlnxsync_class, xlnxsync->dev,
+			   MKDEV(MAJOR(xlnxsync_devt), xlnxsync->minor),
+			   xlnxsync, "xlnxsync%d", xlnxsync->minor);
+	if (IS_ERR(dc)) {
+		ret = PTR_ERR(dc);
+		dev_err(xlnxsync->dev, "Unable to create device");
+		goto cdev_err;
+	}
+
+	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(44));
+	if (ret) {
+		dev_err(&pdev->dev, "dma_set_mask: %d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, xlnxsync);
+	dev_info(xlnxsync->dev, "Xilinx Synchronizer probe successful!\n");
+
+	return 0;
+
+cdev_err:
+	cdev_del(&xlnxsync->chdev);
+clk_err:
+	clk_disable_unprepare(xlnxsync->c_clk);
+	clk_disable_unprepare(xlnxsync->p_clk);
+	clk_disable_unprepare(xlnxsync->axi_clk);
+	ida_simple_remove(&xs_ida, xlnxsync->minor);
+
+	return ret;
+}
+
+static int xlnxsync_remove(struct platform_device *pdev)
+{
+	struct xlnxsync_device *xlnxsync = platform_get_drvdata(pdev);
+
+	if (!xlnxsync || !xlnxsync_class)
+		return -EIO;
+
+	cdev_del(&xlnxsync->chdev);
+	clk_disable_unprepare(xlnxsync->c_clk);
+	clk_disable_unprepare(xlnxsync->p_clk);
+	clk_disable_unprepare(xlnxsync->axi_clk);
+	ida_simple_remove(&xs_ida, xlnxsync->minor);
+
+	return 0;
+}
+
+static const struct of_device_id xlnxsync_of_match[] = {
+	{ .compatible = "xlnx,sync-ip-1.0", },
+	{ /* end of table*/ }
+};
+MODULE_DEVICE_TABLE(of, xlnxsync_of_match);
+
+static struct platform_driver xlnxsync_driver = {
+	.driver = {
+		.name = XLNXSYNC_DRIVER_NAME,
+		.of_match_table = xlnxsync_of_match,
+	},
+	.probe = xlnxsync_probe,
+	.remove = xlnxsync_remove,
+};
+
+static int __init xlnxsync_init_mod(void)
+{
+	int err;
+
+	xlnxsync_class = class_create(THIS_MODULE, XLNXSYNC_DRIVER_NAME);
+	if (IS_ERR(xlnxsync_class)) {
+		pr_err("%s : Unable to create xlnxsync class", __func__);
+		return PTR_ERR(xlnxsync_class);
+	}
+	err = alloc_chrdev_region(&xlnxsync_devt, 0,
+				  XLNXSYNC_DEV_MAX, XLNXSYNC_DRIVER_NAME);
+	if (err < 0) {
+		pr_err("%s: Unable to get major number for xlnxsync", __func__);
+		goto err_class;
+	}
+	err = platform_driver_register(&xlnxsync_driver);
+	if (err < 0) {
+		pr_err("%s: Unable to register %s driver",
+		       __func__, XLNXSYNC_DRIVER_NAME);
+		goto err_pdrv;
+	}
+	return 0;
+err_pdrv:
+	unregister_chrdev_region(xlnxsync_devt, XLNXSYNC_DEV_MAX);
+err_class:
+	class_destroy(xlnxsync_class);
+	return err;
+}
+
+static void __exit xlnxsync_cleanup_mod(void)
+{
+	platform_driver_unregister(&xlnxsync_driver);
+	unregister_chrdev_region(xlnxsync_devt, XLNXSYNC_DEV_MAX);
+	class_destroy(xlnxsync_class);
+	xlnxsync_class = NULL;
+}
+module_init(xlnxsync_init_mod);
+module_exit(xlnxsync_cleanup_mod);
+
+MODULE_AUTHOR("Vishal Sagar");
+MODULE_DESCRIPTION("Xilinx Synchronizer IP Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION(XLNXSYNC_DRIVER_VERSION);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/Kconfig
@@ -0,0 +1,18 @@
+#
+# Xilinx Radio over Ethernet Framer driver
+#
+
+config XROE_FRAMER
+	tristate "Xilinx Radio over Ethernet Framer driver"
+	help
+	  The "Radio Over Ethernet Framer" IP (roe_framer) ingests/generates
+	  Ethernet packet data, (de-)multiplexes packets based on protocol
+	  into/from various Radio Antenna data streams.
+
+	  It has 2 main, independent, data paths:
+
+	  - Downlink, from the BaseBand to the Phone, Ethernet to Antenna,
+	  we call this the De-Framer path, or defm on all related IP signals.
+
+	  - Uplink, from the Phone to the BaseBand, Antenna to Ethernet,
+	  we call this the Framer path, or fram on all related IP signals.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for Radio over Ethernet Framer driver
+#
+obj-$(CONFIG_XROE_FRAMER)	:= framer.o
+
+framer-objs := 	xroe_framer.o \
+		sysfs_xroe.o \
+		sysfs_xroe_framer_ipv4.o \
+		sysfs_xroe_framer_ipv6.o \
+		sysfs_xroe_framer_udp.o \
+		sysfs_xroe_framer_stats.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/README
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/README
@@ -0,0 +1,47 @@
+Xilinx Radio over Ethernet Framer driver
+=========================================
+
+About the RoE Framer
+
+The "Radio Over Ethernet Framer" IP (roe_framer) ingests/generates Ethernet
+packet data, (de-)multiplexes packets based on protocol into/from various
+Radio Antenna data streams.
+
+It has 2 main, independent, data paths
+
+- Downlink, from the BaseBand to the Phone, Ethernet to Antenna,
+we call this the De-Framer path, or defm on all related IP signals.
+
+- Uplink, from the Phone to the BaseBand, Antenna to Ethernet,
+we call this the Framer path, or fram on all related IP signals.
+
+Key points:
+
+- Apart from the AXI4-Lite configuration port and a handful of strobe/control
+signals all data interfaces are AXI Stream(AXIS).
+- The IP does not contain an Ethernet MAC IP, rather it routes, or creates
+packets based on the direction through the roe_framer.
+- Currently designed to work with
+	- 1, 2 or 4 10G Ethernet AXIS stream ports to/from 1, 2, 4, 8, 16,
+	or 32 antenna ports
+		Note: each Ethernet port is 64 bit data @ 156.25MHz
+	- 1 or 2 25G Ethernet AXIS stream ports to/from 1, 2, 4, 8, 16,
+	or 32 antenna ports
+		Note: each Ethernet port is 64 bit data @ 390.25MHz
+- Contains a filter so that all non-protocol packets, or non-hardware-IP
+processed packets can be forwarded to another block for processing. In general
+this in a Microprocessor, specifically the Zynq ARM in our case. This filter
+function can move into the optional switch when TSN is used.
+
+About the Linux Driver
+
+The RoE Framer Linux Driver provides sysfs access to the framer controls. The
+loading of the driver to the hardware is possible using Device Tree binding
+(see "dt-binding.txt" for more information). When the driver is loaded, the
+general controls (such as framing mode, enable, restart etc) are exposed
+under /sys/kernel/xroe. Furthermore, specific controls can be found under
+/sys/kernel/xroe/framer. These include protocol-specific settings, for
+IPv4, IPv6 & UDP.
+
+There is also the option of accessing the framer's register map using
+ioctl calls for both reading and writing (where permitted) directly.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/dt-binding.txt
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/dt-binding.txt
@@ -0,0 +1,17 @@
+* Xilinx Radio over Ethernet Framer driver
+
+Required properties:
+- compatible: must be "xlnx,roe-framer-1.0"
+- reg: physical base address of the framer and length of memory mapped region
+- clock-names: list of clock names
+- clocks: list of clock sources corresponding to the clock names
+
+Example:
+	roe_framer@a0000000 {
+		compatible = "xlnx,roe-framer-1.0";
+		reg = <0x0 0xa0000000 0x0 0x10000>;
+		clock-names = "s_axi_aclk", "m_axis_defm_aclk",
+			      "s_axis_fram_aclk", "tx0_eth_port_clk",
+			      "internal_bus_clk";
+		clocks = <0x43 0x44 0x44 0x45 0x45>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/roe_framer_ctrl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/roe_framer_ctrl.h
@@ -0,0 +1,1088 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+/*-----------------------------------------------------------------------------
+ * C Header bank BASE definitions
+ *-----------------------------------------------------------------------------
+ */
+#define ROE_FRAMER_V1_0_CFG_BASE_ADDR 0x0 /* 0 */
+#define ROE_FRAMER_V1_0_FRAM_BASE_ADDR 0x2000 /* 8192 */
+#define ROE_FRAMER_V1_0_FRAM_DRP_BASE_ADDR 0x4000 /* 16384 */
+#define ROE_FRAMER_V1_0_DEFM_BASE_ADDR 0x6000 /* 24576 */
+#define ROE_FRAMER_V1_0_DEFM_DRP_BASE_ADDR 0x8000 /* 32768 */
+#define ROE_FRAMER_V1_0_ETH_BASE_ADDR 0xa000 /* 40960 */
+#define ROE_FRAMER_V1_0_STATS_BASE_ADDR 0xc000 /* 49152 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_cfg
+ * with prefix cfg_ @ address 0x0
+ *-----------------------------------------------------------------------------
+ */
+/* Type = roInt */
+#define CFG_MAJOR_REVISION_ADDR 0x0 /* 0 */
+#define CFG_MAJOR_REVISION_MASK 0xff000000 /* 4278190080 */
+#define CFG_MAJOR_REVISION_OFFSET 0x18 /* 24 */
+#define CFG_MAJOR_REVISION_WIDTH 0x8 /* 8 */
+#define CFG_MAJOR_REVISION_DEFAULT 0x1 /* 1 */
+
+/* Type = roInt */
+#define CFG_MINOR_REVISION_ADDR 0x0 /* 0 */
+#define CFG_MINOR_REVISION_MASK 0xff0000 /* 16711680 */
+#define CFG_MINOR_REVISION_OFFSET 0x10 /* 16 */
+#define CFG_MINOR_REVISION_WIDTH 0x8 /* 8 */
+#define CFG_MINOR_REVISION_DEFAULT 0x0 /* 0 */
+
+/* Type = roInt */
+#define CFG_VERSION_REVISION_ADDR 0x0 /* 0 */
+#define CFG_VERSION_REVISION_MASK 0xff00 /* 65280 */
+#define CFG_VERSION_REVISION_OFFSET 0x8 /* 8 */
+#define CFG_VERSION_REVISION_WIDTH 0x8 /* 8 */
+#define CFG_VERSION_REVISION_DEFAULT 0x0 /* 0 */
+
+/* Type = roInt */
+#define CFG_INTERNAL_REVISION_ADDR 0x4 /* 4 */
+#define CFG_INTERNAL_REVISION_MASK 0xffffffff /* 4294967295 */
+#define CFG_INTERNAL_REVISION_OFFSET 0x0 /* 0 */
+#define CFG_INTERNAL_REVISION_WIDTH 0x20 /* 32 */
+#define CFG_INTERNAL_REVISION_DEFAULT 0x12345678 /* 305419896 */
+
+/* Type = rw */
+#define CFG_TIMEOUT_VALUE_ADDR 0x8 /* 8 */
+#define CFG_TIMEOUT_VALUE_MASK 0xfff /* 4095 */
+#define CFG_TIMEOUT_VALUE_OFFSET 0x0 /* 0 */
+#define CFG_TIMEOUT_VALUE_WIDTH 0xc /* 12 */
+#define CFG_TIMEOUT_VALUE_DEFAULT 0x80 /* 128 */
+
+/* Type = rw */
+#define CFG_USER_RW_OUT_ADDR 0xc /* 12 */
+#define CFG_USER_RW_OUT_MASK 0xff /* 255 */
+#define CFG_USER_RW_OUT_OFFSET 0x0 /* 0 */
+#define CFG_USER_RW_OUT_WIDTH 0x8 /* 8 */
+#define CFG_USER_RW_OUT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_USER_RO_IN_ADDR 0xc /* 12 */
+#define CFG_USER_RO_IN_MASK 0xff0000 /* 16711680 */
+#define CFG_USER_RO_IN_OFFSET 0x10 /* 16 */
+#define CFG_USER_RO_IN_WIDTH 0x8 /* 8 */
+#define CFG_USER_RO_IN_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define CFG_MASTER_INT_ENABLE_ADDR 0x10 /* 16 */
+#define CFG_MASTER_INT_ENABLE_MASK 0x1 /* 1 */
+#define CFG_MASTER_INT_ENABLE_OFFSET 0x0 /* 0 */
+#define CFG_MASTER_INT_ENABLE_WIDTH 0x1 /* 1 */
+#define CFG_MASTER_INT_ENABLE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define CFG_FRAM_FIFO_OF_ENABLE_ADDR 0x14 /* 20 */
+#define CFG_FRAM_FIFO_OF_ENABLE_MASK 0x1 /* 1 */
+#define CFG_FRAM_FIFO_OF_ENABLE_OFFSET 0x0 /* 0 */
+#define CFG_FRAM_FIFO_OF_ENABLE_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_FIFO_OF_ENABLE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define CFG_FRAM_FIFO_UF_ENABLE_ADDR 0x14 /* 20 */
+#define CFG_FRAM_FIFO_UF_ENABLE_MASK 0x2 /* 2 */
+#define CFG_FRAM_FIFO_UF_ENABLE_OFFSET 0x1 /* 1 */
+#define CFG_FRAM_FIFO_UF_ENABLE_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_FIFO_UF_ENABLE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define CFG_AXI_TIMEOUT_ENABLE_ADDR 0x14 /* 20 */
+#define CFG_AXI_TIMEOUT_ENABLE_MASK 0x80000000 /* 2147483648 */
+#define CFG_AXI_TIMEOUT_ENABLE_OFFSET 0x1f /* 31 */
+#define CFG_AXI_TIMEOUT_ENABLE_WIDTH 0x1 /* 1 */
+#define CFG_AXI_TIMEOUT_ENABLE_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define CFG_INTERRUPT_STATUS_SAMPLE_ADDR 0x1c /* 28 */
+#define CFG_INTERRUPT_STATUS_SAMPLE_MASK 0x1 /* 1 */
+#define CFG_INTERRUPT_STATUS_SAMPLE_OFFSET 0x0 /* 0 */
+#define CFG_INTERRUPT_STATUS_SAMPLE_WIDTH 0x1 /* 1 */
+#define CFG_INTERRUPT_STATUS_SAMPLE_DEFAULT 0x1 /* 1 */
+
+/* Type = roSig */
+#define CFG_FRAM_RESET_STATUS_ADDR 0x18 /* 24 */
+#define CFG_FRAM_RESET_STATUS_MASK 0x1 /* 1 */
+#define CFG_FRAM_RESET_STATUS_OFFSET 0x0 /* 0 */
+#define CFG_FRAM_RESET_STATUS_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_RESET_STATUS_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_DEFM_RESET_STATUS_ADDR 0x18 /* 24 */
+#define CFG_DEFM_RESET_STATUS_MASK 0x2 /* 2 */
+#define CFG_DEFM_RESET_STATUS_OFFSET 0x1 /* 1 */
+#define CFG_DEFM_RESET_STATUS_WIDTH 0x1 /* 1 */
+#define CFG_DEFM_RESET_STATUS_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_FRAM_ANT_OF_INTERRUPT_ADDR 0x18 /* 24 */
+#define CFG_FRAM_ANT_OF_INTERRUPT_MASK 0x100 /* 256 */
+#define CFG_FRAM_ANT_OF_INTERRUPT_OFFSET 0x8 /* 8 */
+#define CFG_FRAM_ANT_OF_INTERRUPT_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_ANT_OF_INTERRUPT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_FRAM_ETH_OF_INTERRUPT_ADDR 0x18 /* 24 */
+#define CFG_FRAM_ETH_OF_INTERRUPT_MASK 0x200 /* 512 */
+#define CFG_FRAM_ETH_OF_INTERRUPT_OFFSET 0x9 /* 9 */
+#define CFG_FRAM_ETH_OF_INTERRUPT_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_ETH_OF_INTERRUPT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_FRAM_ANT_UF_INTERRUPT_ADDR 0x18 /* 24 */
+#define CFG_FRAM_ANT_UF_INTERRUPT_MASK 0x400 /* 1024 */
+#define CFG_FRAM_ANT_UF_INTERRUPT_OFFSET 0xa /* 10 */
+#define CFG_FRAM_ANT_UF_INTERRUPT_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_ANT_UF_INTERRUPT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_FRAM_ETH_UF_INTERRUPT_ADDR 0x18 /* 24 */
+#define CFG_FRAM_ETH_UF_INTERRUPT_MASK 0x800 /* 2048 */
+#define CFG_FRAM_ETH_UF_INTERRUPT_OFFSET 0xb /* 11 */
+#define CFG_FRAM_ETH_UF_INTERRUPT_WIDTH 0x1 /* 1 */
+#define CFG_FRAM_ETH_UF_INTERRUPT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_AXI_TIMEOUT_STATUS_ADDR 0x18 /* 24 */
+#define CFG_AXI_TIMEOUT_STATUS_MASK 0x80000000 /* 2147483648 */
+#define CFG_AXI_TIMEOUT_STATUS_OFFSET 0x1f /* 31 */
+#define CFG_AXI_TIMEOUT_STATUS_WIDTH 0x1 /* 1 */
+#define CFG_AXI_TIMEOUT_STATUS_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_CONFIG_NO_OF_FRAM_ANTS_ADDR 0x20 /* 32 */
+#define CFG_CONFIG_NO_OF_FRAM_ANTS_MASK 0xffff /* 65535 */
+#define CFG_CONFIG_NO_OF_FRAM_ANTS_OFFSET 0x0 /* 0 */
+#define CFG_CONFIG_NO_OF_FRAM_ANTS_WIDTH 0x10 /* 16 */
+#define CFG_CONFIG_NO_OF_FRAM_ANTS_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_CONFIG_NO_OF_DEFM_ANTS_ADDR 0x20 /* 32 */
+#define CFG_CONFIG_NO_OF_DEFM_ANTS_MASK 0xffff0000 /* 4294901760 */
+#define CFG_CONFIG_NO_OF_DEFM_ANTS_OFFSET 0x10 /* 16 */
+#define CFG_CONFIG_NO_OF_DEFM_ANTS_WIDTH 0x10 /* 16 */
+#define CFG_CONFIG_NO_OF_DEFM_ANTS_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_CONFIG_NO_OF_ETH_PORTS_ADDR 0x24 /* 36 */
+#define CFG_CONFIG_NO_OF_ETH_PORTS_MASK 0x3ff /* 1023 */
+#define CFG_CONFIG_NO_OF_ETH_PORTS_OFFSET 0x0 /* 0 */
+#define CFG_CONFIG_NO_OF_ETH_PORTS_WIDTH 0xa /* 10 */
+#define CFG_CONFIG_NO_OF_ETH_PORTS_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define CFG_CONFIG_ETH_SPEED_ADDR 0x24 /* 36 */
+#define CFG_CONFIG_ETH_SPEED_MASK 0x3ff0000 /* 67043328 */
+#define CFG_CONFIG_ETH_SPEED_OFFSET 0x10 /* 16 */
+#define CFG_CONFIG_ETH_SPEED_WIDTH 0xa /* 10 */
+#define CFG_CONFIG_ETH_SPEED_DEFAULT 0x0 /* 0 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_fram
+ * with prefix fram_ @ address 0x2000
+ *------------------------------------------------------------------------------
+ */
+/* Type = rwpdef */
+#define FRAM_DISABLE_ADDR 0x2000 /* 8192 */
+#define FRAM_DISABLE_MASK 0x1 /* 1 */
+#define FRAM_DISABLE_OFFSET 0x0 /* 0 */
+#define FRAM_DISABLE_WIDTH 0x1 /* 1 */
+#define FRAM_DISABLE_DEFAULT 0x1 /* 1 */
+
+/* Type = roSig */
+#define FRAM_READY_ADDR 0x2000 /* 8192 */
+#define FRAM_READY_MASK 0x2 /* 2 */
+#define FRAM_READY_OFFSET 0x1 /* 1 */
+#define FRAM_READY_WIDTH 0x1 /* 1 */
+#define FRAM_READY_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define FRAM_FIFO_FULL_INDICATOR_ADDR 0x2004 /* 8196 */
+#define FRAM_FIFO_FULL_INDICATOR_MASK 0xffffffff /* 4294967295 */
+#define FRAM_FIFO_FULL_INDICATOR_OFFSET 0x0 /* 0 */
+#define FRAM_FIFO_FULL_INDICATOR_WIDTH 0x20 /* 32 */
+#define FRAM_FIFO_FULL_INDICATOR_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_LOW_CNT_MIN_ADDR 0x2020 /* 8224 */
+#define FRAM_SN_DATA_LOW_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_LOW_CNT_MIN_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_LOW_CNT_MIN_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_LOW_CNT_MIN_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_LOW_CNT_MAX_ADDR 0x2024 /* 8228 */
+#define FRAM_SN_DATA_LOW_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_LOW_CNT_MAX_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_LOW_CNT_MAX_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_LOW_CNT_MAX_DEFAULT 0x78 /* 120 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_LOW_CNT_INITVAL_ADDR 0x2028 /* 8232 */
+#define FRAM_SN_DATA_LOW_CNT_INITVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_LOW_CNT_INITVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_LOW_CNT_INITVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_LOW_CNT_INITVAL_DEFAULT 0x75 /* 117 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_LOW_CNT_INCVAL_ADDR 0x202c /* 8236 */
+#define FRAM_SN_DATA_LOW_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_LOW_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_LOW_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_LOW_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_HIGH_CNT_MIN_ADDR 0x2030 /* 8240 */
+#define FRAM_SN_DATA_HIGH_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_HIGH_CNT_MIN_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_HIGH_CNT_MIN_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_HIGH_CNT_MIN_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_HIGH_CNT_MAX_ADDR 0x2034 /* 8244 */
+#define FRAM_SN_DATA_HIGH_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_HIGH_CNT_MAX_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_HIGH_CNT_MAX_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_HIGH_CNT_MAX_DEFAULT 0x4f /* 79 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_HIGH_CNT_INITVAL_ADDR 0x2038 /* 8248 */
+#define FRAM_SN_DATA_HIGH_CNT_INITVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_HIGH_CNT_INITVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_HIGH_CNT_INITVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_HIGH_CNT_INITVAL_DEFAULT 0x4f /* 79 */
+
+/* Type = rw */
+#define FRAM_SN_DATA_HIGH_CNT_INCVAL_ADDR 0x203c /* 8252 */
+#define FRAM_SN_DATA_HIGH_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_DATA_HIGH_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_DATA_HIGH_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_DATA_HIGH_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_LOW_CNT_MIN_ADDR 0x2050 /* 8272 */
+#define FRAM_SN_CTRL_LOW_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_LOW_CNT_MIN_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_LOW_CNT_MIN_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_LOW_CNT_MIN_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_LOW_CNT_MAX_ADDR 0x2054 /* 8276 */
+#define FRAM_SN_CTRL_LOW_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_LOW_CNT_MAX_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_LOW_CNT_MAX_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_LOW_CNT_MAX_DEFAULT 0x78 /* 120 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_LOW_CNT_INITVAL_ADDR 0x2058 /* 8280 */
+#define FRAM_SN_CTRL_LOW_CNT_INITVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_LOW_CNT_INITVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_LOW_CNT_INITVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_LOW_CNT_INITVAL_DEFAULT 0x75 /* 117 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_LOW_CNT_INCVAL_ADDR 0x205c /* 8284 */
+#define FRAM_SN_CTRL_LOW_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_LOW_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_LOW_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_LOW_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_HIGH_CNT_MIN_ADDR 0x2060 /* 8288 */
+#define FRAM_SN_CTRL_HIGH_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_HIGH_CNT_MIN_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_HIGH_CNT_MIN_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_HIGH_CNT_MIN_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_HIGH_CNT_MAX_ADDR 0x2064 /* 8292 */
+#define FRAM_SN_CTRL_HIGH_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_HIGH_CNT_MAX_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_HIGH_CNT_MAX_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_HIGH_CNT_MAX_DEFAULT 0x4f /* 79 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_HIGH_CNT_INITVAL_ADDR 0x2068 /* 8296 */
+#define FRAM_SN_CTRL_HIGH_CNT_INITVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_HIGH_CNT_INITVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_HIGH_CNT_INITVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_HIGH_CNT_INITVAL_DEFAULT 0x4f /* 79 */
+
+/* Type = rw */
+#define FRAM_SN_CTRL_HIGH_CNT_INCVAL_ADDR 0x206c /* 8300 */
+#define FRAM_SN_CTRL_HIGH_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define FRAM_SN_CTRL_HIGH_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define FRAM_SN_CTRL_HIGH_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define FRAM_SN_CTRL_HIGH_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define FRAM_PROTOCOL_DEFINITION_ADDR 0x2200 /* 8704 */
+#define FRAM_PROTOCOL_DEFINITION_MASK 0xf /* 15 */
+#define FRAM_PROTOCOL_DEFINITION_OFFSET 0x0 /* 0 */
+#define FRAM_PROTOCOL_DEFINITION_WIDTH 0x4 /* 4 */
+#define FRAM_PROTOCOL_DEFINITION_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_GEN_VLAN_TAG_ADDR 0x2200 /* 8704 */
+#define FRAM_GEN_VLAN_TAG_MASK 0x10 /* 16 */
+#define FRAM_GEN_VLAN_TAG_OFFSET 0x4 /* 4 */
+#define FRAM_GEN_VLAN_TAG_WIDTH 0x1 /* 1 */
+#define FRAM_GEN_VLAN_TAG_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_SEL_IPV_ADDRESS_TYPE_ADDR 0x2200 /* 8704 */
+#define FRAM_SEL_IPV_ADDRESS_TYPE_MASK 0x60 /* 96 */
+#define FRAM_SEL_IPV_ADDRESS_TYPE_OFFSET 0x5 /* 5 */
+#define FRAM_SEL_IPV_ADDRESS_TYPE_WIDTH 0x2 /* 2 */
+#define FRAM_SEL_IPV_ADDRESS_TYPE_DEFAULT 0x0 /* 0 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_fram_drp
+ * with prefix fram_drp @ address 0x4000
+ *------------------------------------------------------------------------------
+ */
+/* Type = rw */
+#define FRAM_DRPFRAM_DATA_PC_ID_ADDR 0x4000 /* 16384 */
+#define FRAM_DRPFRAM_DATA_PC_ID_MASK 0xffff /* 65535 */
+#define FRAM_DRPFRAM_DATA_PC_ID_OFFSET 0x0 /* 0 */
+#define FRAM_DRPFRAM_DATA_PC_ID_WIDTH 0x10 /* 16 */
+#define FRAM_DRPFRAM_DATA_PC_ID_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_DRPFRAM_DATA_MESSAGE_TYPE_ADDR 0x4000 /* 16384 */
+#define FRAM_DRPFRAM_DATA_MESSAGE_TYPE_MASK 0xff0000 /* 16711680 */
+#define FRAM_DRPFRAM_DATA_MESSAGE_TYPE_OFFSET 0x10 /* 16 */
+#define FRAM_DRPFRAM_DATA_MESSAGE_TYPE_WIDTH 0x8 /* 8 */
+#define FRAM_DRPFRAM_DATA_MESSAGE_TYPE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_DRPFRAM_DATA_ETHERNET_PORT_ADDR 0x4000 /* 16384 */
+#define FRAM_DRPFRAM_DATA_ETHERNET_PORT_MASK 0xff000000 /* 4278190080 */
+#define FRAM_DRPFRAM_DATA_ETHERNET_PORT_OFFSET 0x18 /* 24 */
+#define FRAM_DRPFRAM_DATA_ETHERNET_PORT_WIDTH 0x8 /* 8 */
+#define FRAM_DRPFRAM_DATA_ETHERNET_PORT_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_DRPFRAM_CTRL_PC_ID_ADDR 0x4400 /* 17408 */
+#define FRAM_DRPFRAM_CTRL_PC_ID_MASK 0xffff /* 65535 */
+#define FRAM_DRPFRAM_CTRL_PC_ID_OFFSET 0x0 /* 0 */
+#define FRAM_DRPFRAM_CTRL_PC_ID_WIDTH 0x10 /* 16 */
+#define FRAM_DRPFRAM_CTRL_PC_ID_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_DRPFRAM_CTRL_MESSAGE_TYPE_ADDR 0x4400 /* 17408 */
+#define FRAM_DRPFRAM_CTRL_MESSAGE_TYPE_MASK 0xff0000 /* 16711680 */
+#define FRAM_DRPFRAM_CTRL_MESSAGE_TYPE_OFFSET 0x10 /* 16 */
+#define FRAM_DRPFRAM_CTRL_MESSAGE_TYPE_WIDTH 0x8 /* 8 */
+#define FRAM_DRPFRAM_CTRL_MESSAGE_TYPE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define FRAM_DRPFRAM_CTRL_ETHERNET_PORT_ADDR 0x4400 /* 17408 */
+#define FRAM_DRPFRAM_CTRL_ETHERNET_PORT_MASK 0xff000000 /* 4278190080 */
+#define FRAM_DRPFRAM_CTRL_ETHERNET_PORT_OFFSET 0x18 /* 24 */
+#define FRAM_DRPFRAM_CTRL_ETHERNET_PORT_WIDTH 0x8 /* 8 */
+#define FRAM_DRPFRAM_CTRL_ETHERNET_PORT_DEFAULT 0x0 /* 0 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_defm
+ * with prefix defm_ @ address 0x6000
+ *------------------------------------------------------------------------------
+ */
+/* Type = rw */
+#define DEFM_RESTART_ADDR 0x6000 /* 24576 */
+#define DEFM_RESTART_MASK 0x1 /* 1 */
+#define DEFM_RESTART_OFFSET 0x0 /* 0 */
+#define DEFM_RESTART_WIDTH 0x1 /* 1 */
+#define DEFM_RESTART_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_READY_ADDR 0x6000 /* 24576 */
+#define DEFM_READY_MASK 0x2 /* 2 */
+#define DEFM_READY_OFFSET 0x1 /* 1 */
+#define DEFM_READY_WIDTH 0x1 /* 1 */
+#define DEFM_READY_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_ERR_PACKET_FILTER_ADDR 0x6004 /* 24580 */
+#define DEFM_ERR_PACKET_FILTER_MASK 0x3 /* 3 */
+#define DEFM_ERR_PACKET_FILTER_OFFSET 0x0 /* 0 */
+#define DEFM_ERR_PACKET_FILTER_WIDTH 0x2 /* 2 */
+#define DEFM_ERR_PACKET_FILTER_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_DATA_PKT_MESSAGE_TYPE_ADDR 0x6008 /* 24584 */
+#define DEFM_DATA_PKT_MESSAGE_TYPE_MASK 0xff /* 255 */
+#define DEFM_DATA_PKT_MESSAGE_TYPE_OFFSET 0x0 /* 0 */
+#define DEFM_DATA_PKT_MESSAGE_TYPE_WIDTH 0x8 /* 8 */
+#define DEFM_DATA_PKT_MESSAGE_TYPE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_CTRL_PKT_MESSAGE_TYPE_ADDR 0x600c /* 24588 */
+#define DEFM_CTRL_PKT_MESSAGE_TYPE_MASK 0xff /* 255 */
+#define DEFM_CTRL_PKT_MESSAGE_TYPE_OFFSET 0x0 /* 0 */
+#define DEFM_CTRL_PKT_MESSAGE_TYPE_WIDTH 0x8 /* 8 */
+#define DEFM_CTRL_PKT_MESSAGE_TYPE_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_SN_DATA_LOW_CNT_MIN_ADDR 0x6020 /* 24608 */
+#define DEFM_SN_DATA_LOW_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_DATA_LOW_CNT_MIN_OFFSET 0x0 /* 0 */
+#define DEFM_SN_DATA_LOW_CNT_MIN_WIDTH 0x20 /* 32 */
+#define DEFM_SN_DATA_LOW_CNT_MIN_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define DEFM_SN_DATA_LOW_CNT_MAX_ADDR 0x6024 /* 24612 */
+#define DEFM_SN_DATA_LOW_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_DATA_LOW_CNT_MAX_OFFSET 0x0 /* 0 */
+#define DEFM_SN_DATA_LOW_CNT_MAX_WIDTH 0x20 /* 32 */
+#define DEFM_SN_DATA_LOW_CNT_MAX_DEFAULT 0x78 /* 120 */
+
+/* Type = rw */
+#define DEFM_SN_DATA_LOW_CNT_INCVAL_ADDR 0x602c /* 24620 */
+#define DEFM_SN_DATA_LOW_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_DATA_LOW_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define DEFM_SN_DATA_LOW_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define DEFM_SN_DATA_LOW_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define DEFM_SN_DATA_HIGH_CNT_MIN_ADDR 0x6030 /* 24624 */
+#define DEFM_SN_DATA_HIGH_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_DATA_HIGH_CNT_MIN_OFFSET 0x0 /* 0 */
+#define DEFM_SN_DATA_HIGH_CNT_MIN_WIDTH 0x20 /* 32 */
+#define DEFM_SN_DATA_HIGH_CNT_MIN_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_SN_DATA_HIGH_CNT_MAX_ADDR 0x6034 /* 24628 */
+#define DEFM_SN_DATA_HIGH_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_DATA_HIGH_CNT_MAX_OFFSET 0x0 /* 0 */
+#define DEFM_SN_DATA_HIGH_CNT_MAX_WIDTH 0x20 /* 32 */
+#define DEFM_SN_DATA_HIGH_CNT_MAX_DEFAULT 0x4f /* 79 */
+
+/* Type = rw */
+#define DEFM_SN_DATA_HIGH_CNT_INCVAL_ADDR 0x603c /* 24636 */
+#define DEFM_SN_DATA_HIGH_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_DATA_HIGH_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define DEFM_SN_DATA_HIGH_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define DEFM_SN_DATA_HIGH_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define DEFM_SN_CTRL_LOW_CNT_MIN_ADDR 0x6050 /* 24656 */
+#define DEFM_SN_CTRL_LOW_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_CTRL_LOW_CNT_MIN_OFFSET 0x0 /* 0 */
+#define DEFM_SN_CTRL_LOW_CNT_MIN_WIDTH 0x20 /* 32 */
+#define DEFM_SN_CTRL_LOW_CNT_MIN_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define DEFM_SN_CTRL_LOW_CNT_MAX_ADDR 0x6054 /* 24660 */
+#define DEFM_SN_CTRL_LOW_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_CTRL_LOW_CNT_MAX_OFFSET 0x0 /* 0 */
+#define DEFM_SN_CTRL_LOW_CNT_MAX_WIDTH 0x20 /* 32 */
+#define DEFM_SN_CTRL_LOW_CNT_MAX_DEFAULT 0x78 /* 120 */
+
+/* Type = rw */
+#define DEFM_SN_CTRL_LOW_CNT_INCVAL_ADDR 0x605c /* 24668 */
+#define DEFM_SN_CTRL_LOW_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_CTRL_LOW_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define DEFM_SN_CTRL_LOW_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define DEFM_SN_CTRL_LOW_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rw */
+#define DEFM_SN_CTRL_HIGH_CNT_MIN_ADDR 0x6060 /* 24672 */
+#define DEFM_SN_CTRL_HIGH_CNT_MIN_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_CTRL_HIGH_CNT_MIN_OFFSET 0x0 /* 0 */
+#define DEFM_SN_CTRL_HIGH_CNT_MIN_WIDTH 0x20 /* 32 */
+#define DEFM_SN_CTRL_HIGH_CNT_MIN_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_SN_CTRL_HIGH_CNT_MAX_ADDR 0x6064 /* 24676 */
+#define DEFM_SN_CTRL_HIGH_CNT_MAX_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_CTRL_HIGH_CNT_MAX_OFFSET 0x0 /* 0 */
+#define DEFM_SN_CTRL_HIGH_CNT_MAX_WIDTH 0x20 /* 32 */
+#define DEFM_SN_CTRL_HIGH_CNT_MAX_DEFAULT 0x4f /* 79 */
+
+/* Type = rw */
+#define DEFM_SN_CTRL_HIGH_CNT_INCVAL_ADDR 0x606c /* 24684 */
+#define DEFM_SN_CTRL_HIGH_CNT_INCVAL_MASK 0xffffffff /* 4294967295 */
+#define DEFM_SN_CTRL_HIGH_CNT_INCVAL_OFFSET 0x0 /* 0 */
+#define DEFM_SN_CTRL_HIGH_CNT_INCVAL_WIDTH 0x20 /* 32 */
+#define DEFM_SN_CTRL_HIGH_CNT_INCVAL_DEFAULT 0x1 /* 1 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W0_31_0_ADDR 0x6100 /* 24832 */
+#define DEFM_USER_DATA_FILTER_W0_31_0_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W0_31_0_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W0_31_0_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W0_31_0_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W0_63_32_ADDR 0x6104 /* 24836 */
+#define DEFM_USER_DATA_FILTER_W0_63_32_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W0_63_32_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W0_63_32_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W0_63_32_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W0_95_64_ADDR 0x6108 /* 24840 */
+#define DEFM_USER_DATA_FILTER_W0_95_64_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W0_95_64_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W0_95_64_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W0_95_64_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W0_127_96_ADDR 0x610c /* 24844 */
+#define DEFM_USER_DATA_FILTER_W0_127_96_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W0_127_96_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W0_127_96_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W0_127_96_DEFAULT 0xfffffeae /* 4294966958 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W0_MASK_ADDR 0x6110 /* 24848 */
+#define DEFM_USER_DATA_FILTER_W0_MASK_MASK 0xffff /* 65535 */
+#define DEFM_USER_DATA_FILTER_W0_MASK_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W0_MASK_WIDTH 0x10 /* 16 */
+#define DEFM_USER_DATA_FILTER_W0_MASK_DEFAULT 0xcfff /* 53247 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W1_31_0_ADDR 0x6120 /* 24864 */
+#define DEFM_USER_DATA_FILTER_W1_31_0_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W1_31_0_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W1_31_0_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W1_31_0_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W1_63_32_ADDR 0x6124 /* 24868 */
+#define DEFM_USER_DATA_FILTER_W1_63_32_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W1_63_32_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W1_63_32_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W1_63_32_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W1_95_64_ADDR 0x6128 /* 24872 */
+#define DEFM_USER_DATA_FILTER_W1_95_64_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W1_95_64_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W1_95_64_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W1_95_64_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W1_127_96_ADDR 0x612c /* 24876 */
+#define DEFM_USER_DATA_FILTER_W1_127_96_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W1_127_96_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W1_127_96_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W1_127_96_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W1_MASK_ADDR 0x6130 /* 24880 */
+#define DEFM_USER_DATA_FILTER_W1_MASK_MASK 0xffff /* 65535 */
+#define DEFM_USER_DATA_FILTER_W1_MASK_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W1_MASK_WIDTH 0x10 /* 16 */
+#define DEFM_USER_DATA_FILTER_W1_MASK_DEFAULT 0xffff /* 65535 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W2_31_0_ADDR 0x6140 /* 24896 */
+#define DEFM_USER_DATA_FILTER_W2_31_0_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W2_31_0_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W2_31_0_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W2_31_0_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W2_63_32_ADDR 0x6144 /* 24900 */
+#define DEFM_USER_DATA_FILTER_W2_63_32_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W2_63_32_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W2_63_32_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W2_63_32_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W2_95_64_ADDR 0x6148 /* 24904 */
+#define DEFM_USER_DATA_FILTER_W2_95_64_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W2_95_64_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W2_95_64_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W2_95_64_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W2_127_96_ADDR 0x614c /* 24908 */
+#define DEFM_USER_DATA_FILTER_W2_127_96_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W2_127_96_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W2_127_96_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W2_127_96_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W2_MASK_ADDR 0x6150 /* 24912 */
+#define DEFM_USER_DATA_FILTER_W2_MASK_MASK 0xffff /* 65535 */
+#define DEFM_USER_DATA_FILTER_W2_MASK_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W2_MASK_WIDTH 0x10 /* 16 */
+#define DEFM_USER_DATA_FILTER_W2_MASK_DEFAULT 0xffff /* 65535 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W3_31_0_ADDR 0x6160 /* 24928 */
+#define DEFM_USER_DATA_FILTER_W3_31_0_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W3_31_0_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W3_31_0_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W3_31_0_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W3_63_32_ADDR 0x6164 /* 24932 */
+#define DEFM_USER_DATA_FILTER_W3_63_32_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W3_63_32_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W3_63_32_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W3_63_32_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W3_95_64_ADDR 0x6168 /* 24936 */
+#define DEFM_USER_DATA_FILTER_W3_95_64_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W3_95_64_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W3_95_64_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W3_95_64_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W3_127_96_ADDR 0x616c /* 24940 */
+#define DEFM_USER_DATA_FILTER_W3_127_96_MASK 0xffffffff /* 4294967295 */
+#define DEFM_USER_DATA_FILTER_W3_127_96_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W3_127_96_WIDTH 0x20 /* 32 */
+#define DEFM_USER_DATA_FILTER_W3_127_96_DEFAULT 0xffffffff /* 4294967295 */
+
+/* Type = rwpdef */
+#define DEFM_USER_DATA_FILTER_W3_MASK_ADDR 0x6170 /* 24944 */
+#define DEFM_USER_DATA_FILTER_W3_MASK_MASK 0xffff /* 65535 */
+#define DEFM_USER_DATA_FILTER_W3_MASK_OFFSET 0x0 /* 0 */
+#define DEFM_USER_DATA_FILTER_W3_MASK_WIDTH 0x10 /* 16 */
+#define DEFM_USER_DATA_FILTER_W3_MASK_DEFAULT 0xffff /* 65535 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_defm_drp
+ * with prefix defm_drp @ address 0x8000
+ *------------------------------------------------------------------------------
+ */
+/* Type = rw */
+#define DEFM_DRPDEFM_DATA_PC_ID_ADDR 0x8000 /* 32768 */
+#define DEFM_DRPDEFM_DATA_PC_ID_MASK 0xffff /* 65535 */
+#define DEFM_DRPDEFM_DATA_PC_ID_OFFSET 0x0 /* 0 */
+#define DEFM_DRPDEFM_DATA_PC_ID_WIDTH 0x10 /* 16 */
+#define DEFM_DRPDEFM_DATA_PC_ID_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define DEFM_DRPDEFM_CTRL_PC_ID_ADDR 0x8400 /* 33792 */
+#define DEFM_DRPDEFM_CTRL_PC_ID_MASK 0xffff /* 65535 */
+#define DEFM_DRPDEFM_CTRL_PC_ID_OFFSET 0x0 /* 0 */
+#define DEFM_DRPDEFM_CTRL_PC_ID_WIDTH 0x10 /* 16 */
+#define DEFM_DRPDEFM_CTRL_PC_ID_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_LATENCY_ADDR 0x8800 /* 34816 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_LATENCY_MASK 0xffffff /* 16777215 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_LATENCY_OFFSET 0x0 /* 0 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_LATENCY_WIDTH 0x18 /* 24 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_LATENCY_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_ALIGNMENT_ADDR 0x8800 /* 34816 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_ALIGNMENT_MASK 0x1000000 /* 16777216 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_ALIGNMENT_OFFSET 0x18 /* 24 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_ALIGNMENT_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_ALIGNMENT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_OVERFLOW_ADDR 0x8800 /* 34816 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_OVERFLOW_MASK 0x2000000 /* 33554432 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_OVERFLOW_OFFSET 0x19 /* 25 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_OVERFLOW_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_OVERFLOW_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_UNDERFLOW_ADDR 0x8800 /* 34816 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_UNDERFLOW_MASK 0x4000000 /* 67108864 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_UNDERFLOW_OFFSET 0x1a /* 26 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_UNDERFLOW_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_UNDERFLOW_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_REGULAR_ADDR 0x8800 /* 34816 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_REGULAR_MASK 0x8000000 /* 134217728 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_REGULAR_OFFSET 0x1b /* 27 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_REGULAR_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_REGULAR_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_RWIN_ADDR 0x8800 /* 34816 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_RWIN_MASK 0xf0000000 /* 4026531840 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_RWIN_OFFSET 0x1c /* 28 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_RWIN_WIDTH 0x4 /* 4 */
+#define DEFM_DRPDEFM_DATA_BUFFER_STATE_RWIN_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_LATENCY_ADDR 0x9800 /* 38912 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_LATENCY_MASK 0xffffff /* 16777215 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_LATENCY_OFFSET 0x0 /* 0 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_LATENCY_WIDTH 0x18 /* 24 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_LATENCY_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_ALIGNMENT_ADDR 0x9800 /* 38912 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_ALIGNMENT_MASK 0x1000000 /* 16777216 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_ALIGNMENT_OFFSET 0x18 /* 24 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_ALIGNMENT_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_ALIGNMENT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_OVERFLOW_ADDR 0x9800 /* 38912 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_OVERFLOW_MASK 0x2000000 /* 33554432 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_OVERFLOW_OFFSET 0x19 /* 25 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_OVERFLOW_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_OVERFLOW_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_UNDERFLOW_ADDR 0x9800 /* 38912 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_UNDERFLOW_MASK 0x4000000 /* 67108864 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_UNDERFLOW_OFFSET 0x1a /* 26 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_UNDERFLOW_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_UNDERFLOW_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_REGULAR_ADDR 0x9800 /* 38912 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_REGULAR_MASK 0x8000000 /* 134217728 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_REGULAR_OFFSET 0x1b /* 27 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_REGULAR_WIDTH 0x1 /* 1 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_REGULAR_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_RWIN_ADDR 0x9800 /* 38912 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_RWIN_MASK 0xf0000000 /* 4026531840 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_RWIN_OFFSET 0x1c /* 28 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_RWIN_WIDTH 0x4 /* 4 */
+#define DEFM_DRPDEFM_CTRL_BUFFER_STATE_RWIN_DEFAULT 0x0 /* 0 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_eth
+ * with prefix eth_ @ address 0xa000
+ *------------------------------------------------------------------------------
+ */
+/* Type = rwpdef */
+#define ETH_DEST_ADDR_31_0_ADDR 0xa000 /* 40960 */
+#define ETH_DEST_ADDR_31_0_MASK 0xffffffff /* 4294967295 */
+#define ETH_DEST_ADDR_31_0_OFFSET 0x0 /* 0 */
+#define ETH_DEST_ADDR_31_0_WIDTH 0x20 /* 32 */
+#define ETH_DEST_ADDR_31_0_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_DEST_ADDR_47_32_ADDR 0xa004 /* 40964 */
+#define ETH_DEST_ADDR_47_32_MASK 0xffff /* 65535 */
+#define ETH_DEST_ADDR_47_32_OFFSET 0x0 /* 0 */
+#define ETH_DEST_ADDR_47_32_WIDTH 0x10 /* 16 */
+#define ETH_DEST_ADDR_47_32_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_SRC_ADDR_31_0_ADDR 0xa008 /* 40968 */
+#define ETH_SRC_ADDR_31_0_MASK 0xffffffff /* 4294967295 */
+#define ETH_SRC_ADDR_31_0_OFFSET 0x0 /* 0 */
+#define ETH_SRC_ADDR_31_0_WIDTH 0x20 /* 32 */
+#define ETH_SRC_ADDR_31_0_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_SRC_ADDR_47_32_ADDR 0xa00c /* 40972 */
+#define ETH_SRC_ADDR_47_32_MASK 0xffff /* 65535 */
+#define ETH_SRC_ADDR_47_32_OFFSET 0x0 /* 0 */
+#define ETH_SRC_ADDR_47_32_WIDTH 0x10 /* 16 */
+#define ETH_SRC_ADDR_47_32_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_VLAN_ID_ADDR 0xa010 /* 40976 */
+#define ETH_VLAN_ID_MASK 0xfff /* 4095 */
+#define ETH_VLAN_ID_OFFSET 0x0 /* 0 */
+#define ETH_VLAN_ID_WIDTH 0xc /* 12 */
+#define ETH_VLAN_ID_DEFAULT 0x1 /* 1 */
+
+/* Type = rwpdef */
+#define ETH_VLAN_DEI_ADDR 0xa010 /* 40976 */
+#define ETH_VLAN_DEI_MASK 0x1000 /* 4096 */
+#define ETH_VLAN_DEI_OFFSET 0xc /* 12 */
+#define ETH_VLAN_DEI_WIDTH 0x1 /* 1 */
+#define ETH_VLAN_DEI_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_VLAN_PCP_ADDR 0xa010 /* 40976 */
+#define ETH_VLAN_PCP_MASK 0xe000 /* 57344 */
+#define ETH_VLAN_PCP_OFFSET 0xd /* 13 */
+#define ETH_VLAN_PCP_WIDTH 0x3 /* 3 */
+#define ETH_VLAN_PCP_DEFAULT 0x7 /* 7 */
+
+/* Type = rw */
+#define ETH_IPV4_VERSION_ADDR 0xa030 /* 41008 */
+#define ETH_IPV4_VERSION_MASK 0xf /* 15 */
+#define ETH_IPV4_VERSION_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_VERSION_WIDTH 0x4 /* 4 */
+#define ETH_IPV4_VERSION_DEFAULT 0x4 /* 4 */
+
+/* Type = rw */
+#define ETH_IPV4_IHL_ADDR 0xa030 /* 41008 */
+#define ETH_IPV4_IHL_MASK 0xf0 /* 240 */
+#define ETH_IPV4_IHL_OFFSET 0x4 /* 4 */
+#define ETH_IPV4_IHL_WIDTH 0x4 /* 4 */
+#define ETH_IPV4_IHL_DEFAULT 0x5 /* 5 */
+
+/* Type = rw */
+#define ETH_IPV4_DSCP_ADDR 0xa034 /* 41012 */
+#define ETH_IPV4_DSCP_MASK 0x3f /* 63 */
+#define ETH_IPV4_DSCP_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_DSCP_WIDTH 0x6 /* 6 */
+#define ETH_IPV4_DSCP_DEFAULT 0x2e /* 46 */
+
+/* Type = rw */
+#define ETH_IPV4_ECN_ADDR 0xa034 /* 41012 */
+#define ETH_IPV4_ECN_MASK 0xc0 /* 192 */
+#define ETH_IPV4_ECN_OFFSET 0x6 /* 6 */
+#define ETH_IPV4_ECN_WIDTH 0x2 /* 2 */
+#define ETH_IPV4_ECN_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define ETH_IPV4_ID_ADDR 0xa038 /* 41016 */
+#define ETH_IPV4_ID_MASK 0xffff /* 65535 */
+#define ETH_IPV4_ID_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_ID_WIDTH 0x10 /* 16 */
+#define ETH_IPV4_ID_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define ETH_IPV4_FLAGS_ADDR 0xa03c /* 41020 */
+#define ETH_IPV4_FLAGS_MASK 0x7 /* 7 */
+#define ETH_IPV4_FLAGS_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_FLAGS_WIDTH 0x3 /* 3 */
+#define ETH_IPV4_FLAGS_DEFAULT 0x2 /* 2 */
+
+/* Type = rw */
+#define ETH_IPV4_FRAGMENT_OFFSET_ADDR 0xa03c /* 41020 */
+#define ETH_IPV4_FRAGMENT_OFFSET_MASK 0x1fff8 /* 131064 */
+#define ETH_IPV4_FRAGMENT_OFFSET_OFFSET 0x3 /* 3 */
+#define ETH_IPV4_FRAGMENT_OFFSET_WIDTH 0xe /* 14 */
+#define ETH_IPV4_FRAGMENT_OFFSET_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define ETH_IPV4_TIME_TO_LIVE_ADDR 0xa040 /* 41024 */
+#define ETH_IPV4_TIME_TO_LIVE_MASK 0xff /* 255 */
+#define ETH_IPV4_TIME_TO_LIVE_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_TIME_TO_LIVE_WIDTH 0x8 /* 8 */
+#define ETH_IPV4_TIME_TO_LIVE_DEFAULT 0x40 /* 64 */
+
+/* Type = rw */
+#define ETH_IPV4_PROTOCOL_ADDR 0xa044 /* 41028 */
+#define ETH_IPV4_PROTOCOL_MASK 0xff /* 255 */
+#define ETH_IPV4_PROTOCOL_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_PROTOCOL_WIDTH 0x8 /* 8 */
+#define ETH_IPV4_PROTOCOL_DEFAULT 0x11 /* 17 */
+
+/* Type = rwpdef */
+#define ETH_IPV4_SOURCE_ADD_ADDR 0xa048 /* 41032 */
+#define ETH_IPV4_SOURCE_ADD_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV4_SOURCE_ADD_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_SOURCE_ADD_WIDTH 0x20 /* 32 */
+#define ETH_IPV4_SOURCE_ADD_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV4_DESTINATION_ADD_ADDR 0xa04c /* 41036 */
+#define ETH_IPV4_DESTINATION_ADD_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV4_DESTINATION_ADD_OFFSET 0x0 /* 0 */
+#define ETH_IPV4_DESTINATION_ADD_WIDTH 0x20 /* 32 */
+#define ETH_IPV4_DESTINATION_ADD_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define ETH_UDP_SOURCE_PORT_ADDR 0xa050 /* 41040 */
+#define ETH_UDP_SOURCE_PORT_MASK 0xffff /* 65535 */
+#define ETH_UDP_SOURCE_PORT_OFFSET 0x0 /* 0 */
+#define ETH_UDP_SOURCE_PORT_WIDTH 0x10 /* 16 */
+#define ETH_UDP_SOURCE_PORT_DEFAULT 0x8000 /* 32768 */
+
+/* Type = rw */
+#define ETH_UDP_DESTINATION_PORT_ADDR 0xa050 /* 41040 */
+#define ETH_UDP_DESTINATION_PORT_MASK 0xffff0000 /* 4294901760 */
+#define ETH_UDP_DESTINATION_PORT_OFFSET 0x10 /* 16 */
+#define ETH_UDP_DESTINATION_PORT_WIDTH 0x10 /* 16 */
+#define ETH_UDP_DESTINATION_PORT_DEFAULT 0xc000 /* 49152 */
+
+/* Type = rw */
+#define ETH_IPV6_V_ADDR 0xa080 /* 41088 */
+#define ETH_IPV6_V_MASK 0xf /* 15 */
+#define ETH_IPV6_V_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_V_WIDTH 0x4 /* 4 */
+#define ETH_IPV6_V_DEFAULT 0x6 /* 6 */
+
+/* Type = rw */
+#define ETH_IPV6_TRAFFIC_CLASS_ADDR 0xa084 /* 41092 */
+#define ETH_IPV6_TRAFFIC_CLASS_MASK 0xff /* 255 */
+#define ETH_IPV6_TRAFFIC_CLASS_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_TRAFFIC_CLASS_WIDTH 0x8 /* 8 */
+#define ETH_IPV6_TRAFFIC_CLASS_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define ETH_IPV6_FLOW_LABEL_ADDR 0xa088 /* 41096 */
+#define ETH_IPV6_FLOW_LABEL_MASK 0xfffff /* 1048575 */
+#define ETH_IPV6_FLOW_LABEL_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_FLOW_LABEL_WIDTH 0x14 /* 20 */
+#define ETH_IPV6_FLOW_LABEL_DEFAULT 0x0 /* 0 */
+
+/* Type = rw */
+#define ETH_IPV6_NEXT_HEADER_ADDR 0xa08c /* 41100 */
+#define ETH_IPV6_NEXT_HEADER_MASK 0xff /* 255 */
+#define ETH_IPV6_NEXT_HEADER_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_NEXT_HEADER_WIDTH 0x8 /* 8 */
+#define ETH_IPV6_NEXT_HEADER_DEFAULT 0x11 /* 17 */
+
+/* Type = rw */
+#define ETH_IPV6_HOP_LIMIT_ADDR 0xa090 /* 41104 */
+#define ETH_IPV6_HOP_LIMIT_MASK 0xff /* 255 */
+#define ETH_IPV6_HOP_LIMIT_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_HOP_LIMIT_WIDTH 0x8 /* 8 */
+#define ETH_IPV6_HOP_LIMIT_DEFAULT 0x40 /* 64 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_SOURCE_ADD_31_0_ADDR 0xa094 /* 41108 */
+#define ETH_IPV6_SOURCE_ADD_31_0_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_SOURCE_ADD_31_0_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_SOURCE_ADD_31_0_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_SOURCE_ADD_31_0_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_SOURCE_ADD_63_32_ADDR 0xa098 /* 41112 */
+#define ETH_IPV6_SOURCE_ADD_63_32_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_SOURCE_ADD_63_32_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_SOURCE_ADD_63_32_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_SOURCE_ADD_63_32_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_SOURCE_ADD_95_64_ADDR 0xa09c /* 41116 */
+#define ETH_IPV6_SOURCE_ADD_95_64_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_SOURCE_ADD_95_64_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_SOURCE_ADD_95_64_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_SOURCE_ADD_95_64_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_SOURCE_ADD_127_96_ADDR 0xa0a0 /* 41120 */
+#define ETH_IPV6_SOURCE_ADD_127_96_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_SOURCE_ADD_127_96_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_SOURCE_ADD_127_96_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_SOURCE_ADD_127_96_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_DEST_ADD_31_0_ADDR 0xa0a4 /* 41124 */
+#define ETH_IPV6_DEST_ADD_31_0_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_DEST_ADD_31_0_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_DEST_ADD_31_0_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_DEST_ADD_31_0_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_DEST_ADD_63_32_ADDR 0xa0a8 /* 41128 */
+#define ETH_IPV6_DEST_ADD_63_32_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_DEST_ADD_63_32_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_DEST_ADD_63_32_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_DEST_ADD_63_32_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_DEST_ADD_95_64_ADDR 0xa0ac /* 41132 */
+#define ETH_IPV6_DEST_ADD_95_64_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_DEST_ADD_95_64_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_DEST_ADD_95_64_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_DEST_ADD_95_64_DEFAULT 0x0 /* 0 */
+
+/* Type = rwpdef */
+#define ETH_IPV6_DEST_ADD_127_96_ADDR 0xa0b0 /* 41136 */
+#define ETH_IPV6_DEST_ADD_127_96_MASK 0xffffffff /* 4294967295 */
+#define ETH_IPV6_DEST_ADD_127_96_OFFSET 0x0 /* 0 */
+#define ETH_IPV6_DEST_ADD_127_96_WIDTH 0x20 /* 32 */
+#define ETH_IPV6_DEST_ADD_127_96_DEFAULT 0x0 /* 0 */
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_framer_v1_0_stats
+ * with prefix stats_ @ address 0xc000
+ *------------------------------------------------------------------------------
+ */
+/* Type = roSig */
+#define STATS_TOTAL_RX_GOOD_PKT_CNT_ADDR 0xc000 /* 49152 */
+#define STATS_TOTAL_RX_GOOD_PKT_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_TOTAL_RX_GOOD_PKT_CNT_OFFSET 0x0 /* 0 */
+#define STATS_TOTAL_RX_GOOD_PKT_CNT_WIDTH 0x20 /* 32 */
+#define STATS_TOTAL_RX_GOOD_PKT_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_TOTAL_RX_BAD_PKT_CNT_ADDR 0xc004 /* 49156 */
+#define STATS_TOTAL_RX_BAD_PKT_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_TOTAL_RX_BAD_PKT_CNT_OFFSET 0x0 /* 0 */
+#define STATS_TOTAL_RX_BAD_PKT_CNT_WIDTH 0x20 /* 32 */
+#define STATS_TOTAL_RX_BAD_PKT_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_TOTAL_RX_BAD_FCS_CNT_ADDR 0xc008 /* 49160 */
+#define STATS_TOTAL_RX_BAD_FCS_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_TOTAL_RX_BAD_FCS_CNT_OFFSET 0x0 /* 0 */
+#define STATS_TOTAL_RX_BAD_FCS_CNT_WIDTH 0x20 /* 32 */
+#define STATS_TOTAL_RX_BAD_FCS_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_DATA_RX_PACKETS_CNT_ADDR 0xc00c /* 49164 */
+#define STATS_USER_DATA_RX_PACKETS_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_DATA_RX_PACKETS_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_DATA_RX_PACKETS_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_DATA_RX_PACKETS_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_DATA_RX_GOOD_PKT_CNT_ADDR 0xc010 /* 49168 */
+#define STATS_USER_DATA_RX_GOOD_PKT_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_DATA_RX_GOOD_PKT_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_DATA_RX_GOOD_PKT_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_DATA_RX_GOOD_PKT_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_DATA_RX_BAD_PKT_CNT_ADDR 0xc014 /* 49172 */
+#define STATS_USER_DATA_RX_BAD_PKT_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_DATA_RX_BAD_PKT_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_DATA_RX_BAD_PKT_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_DATA_RX_BAD_PKT_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_DATA_RX_BAD_FCS_CNT_ADDR 0xc018 /* 49176 */
+#define STATS_USER_DATA_RX_BAD_FCS_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_DATA_RX_BAD_FCS_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_DATA_RX_BAD_FCS_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_DATA_RX_BAD_FCS_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_CTRL_RX_PACKETS_CNT_ADDR 0xc01c /* 49180 */
+#define STATS_USER_CTRL_RX_PACKETS_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_CTRL_RX_PACKETS_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_CTRL_RX_PACKETS_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_CTRL_RX_PACKETS_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_CTRL_RX_GOOD_PKT_CNT_ADDR 0xc020 /* 49184 */
+#define STATS_USER_CTRL_RX_GOOD_PKT_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_CTRL_RX_GOOD_PKT_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_CTRL_RX_GOOD_PKT_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_CTRL_RX_GOOD_PKT_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_CTRL_RX_BAD_PKT_CNT_ADDR 0xc024 /* 49188 */
+#define STATS_USER_CTRL_RX_BAD_PKT_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_CTRL_RX_BAD_PKT_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_CTRL_RX_BAD_PKT_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_CTRL_RX_BAD_PKT_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_CTRL_RX_BAD_FCS_CNT_ADDR 0xc028 /* 49192 */
+#define STATS_USER_CTRL_RX_BAD_FCS_CNT_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_CTRL_RX_BAD_FCS_CNT_OFFSET 0x0 /* 0 */
+#define STATS_USER_CTRL_RX_BAD_FCS_CNT_WIDTH 0x20 /* 32 */
+#define STATS_USER_CTRL_RX_BAD_FCS_CNT_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_DATA_RX_PKTS_RATE_ADDR 0xc02c /* 49196 */
+#define STATS_USER_DATA_RX_PKTS_RATE_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_DATA_RX_PKTS_RATE_OFFSET 0x0 /* 0 */
+#define STATS_USER_DATA_RX_PKTS_RATE_WIDTH 0x20 /* 32 */
+#define STATS_USER_DATA_RX_PKTS_RATE_DEFAULT 0x0 /* 0 */
+
+/* Type = roSig */
+#define STATS_USER_CTRL_RX_PKTS_RATE_ADDR 0xc030 /* 49200 */
+#define STATS_USER_CTRL_RX_PKTS_RATE_MASK 0xffffffff /* 4294967295 */
+#define STATS_USER_CTRL_RX_PKTS_RATE_OFFSET 0x0 /* 0 */
+#define STATS_USER_CTRL_RX_PKTS_RATE_WIDTH 0x20 /* 32 */
+#define STATS_USER_CTRL_RX_PKTS_RATE_DEFAULT 0x0 /* 0 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/sysfs_xroe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/sysfs_xroe.c
@@ -0,0 +1,562 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "xroe_framer.h"
+
+enum { XROE_SIZE_MAX = 15 };
+static int xroe_size;
+static char xroe_tmp[XROE_SIZE_MAX];
+
+/**
+ * version_show - Returns the block's revision number
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the revision string
+ *
+ * Returns the block's major, minor & version revision numbers
+ * in a %d.%d.%d format
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t version_show(struct kobject *kobj, struct kobj_attribute *attr,
+			    char *buff)
+{
+	u32 major_rev;
+	u32 minor_rev;
+	u32 version_rev;
+
+	major_rev = utils_sysfs_show_wrapper(CFG_MAJOR_REVISION_ADDR,
+					     CFG_MAJOR_REVISION_OFFSET,
+					     CFG_MAJOR_REVISION_MASK, kobj);
+	minor_rev = utils_sysfs_show_wrapper(CFG_MINOR_REVISION_ADDR,
+					     CFG_MINOR_REVISION_OFFSET,
+					     CFG_MINOR_REVISION_MASK, kobj);
+	version_rev = utils_sysfs_show_wrapper(CFG_VERSION_REVISION_ADDR,
+					       CFG_VERSION_REVISION_OFFSET,
+					       CFG_VERSION_REVISION_MASK, kobj);
+	sprintf(buff, "%d.%d.%d\n", major_rev, minor_rev, version_rev);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * version_store - Writes to the framer version sysfs entry (not permitted)
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the revision string
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the framer version sysfs entry (not permitted)
+ *
+ * Return: 0
+ */
+static ssize_t version_store(struct  kobject *kobj, struct kobj_attribute *attr,
+			     const char *buff, size_t count)
+{
+	return 0;
+}
+
+/**
+ * enable_show - Returns the framer's enable status
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the enable status
+ *
+ * Reads and writes the framer's enable status to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t enable_show(struct kobject *kobj, struct kobj_attribute *attr,
+			   char *buff)
+{
+	u32 enable;
+
+	enable = utils_sysfs_show_wrapper(CFG_MASTER_INT_ENABLE_ADDR,
+					  CFG_MASTER_INT_ENABLE_OFFSET,
+					  CFG_MASTER_INT_ENABLE_MASK, kobj);
+	if (enable)
+		sprintf(buff, "true\n");
+	else
+		sprintf(buff, "false\n");
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * version_store - Writes to the framer's enable status register
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the enable status
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the framer's enable status
+ * to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t enable_store(struct kobject *kobj, struct kobj_attribute *attr,
+			    const char *buff, size_t count)
+{
+	u32 enable = 0;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (strncmp(xroe_tmp, "true", xroe_size) == 0)
+		enable = 1;
+	else if (strncmp(xroe_tmp, "false", xroe_size) == 0)
+		enable = 0;
+	utils_sysfs_store_wrapper(CFG_MASTER_INT_ENABLE_ADDR,
+				  CFG_MASTER_INT_ENABLE_OFFSET,
+				  CFG_MASTER_INT_ENABLE_MASK, enable, kobj);
+	return xroe_size;
+}
+
+/**
+ * framer_restart_show - Returns the framer's restart status
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the restart status
+ *
+ * Reads and writes the framer's restart status to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t framer_restart_show(struct kobject *kobj,
+				   struct kobj_attribute *attr, char *buff)
+{
+	u32 restart;
+
+	restart = utils_sysfs_show_wrapper(FRAM_DISABLE_ADDR,
+					   FRAM_DISABLE_OFFSET,
+					   FRAM_DISABLE_MASK, kobj);
+	if (restart)
+		sprintf(buff, "true\n");
+
+	else
+		sprintf(buff, "false\n");
+
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * framer_restart_store - Writes to the framer's restart status register
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the restart status
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the framer's restart status
+ * to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t framer_restart_store(struct  kobject *kobj,
+				    struct kobj_attribute *attr,
+				    const char *buff, size_t count)
+{
+	u32 restart = 0;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (strncmp(xroe_tmp, "true", xroe_size) == 0)
+		restart = 0x01;
+	else if (strncmp(xroe_tmp, "false", xroe_size) == 0)
+		restart = 0x00;
+	utils_sysfs_store_wrapper(FRAM_DISABLE_ADDR, FRAM_DISABLE_OFFSET,
+				  FRAM_DISABLE_MASK, restart, kobj);
+	return xroe_size;
+}
+
+/**
+ * deframer_restart_show - Returns the deframer's restart status
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the restart status
+ *
+ * Reads and writes the deframer's restart status to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t deframer_restart_show(struct kobject *kobj,
+				     struct kobj_attribute *attr, char *buff)
+{
+	u32 offset = DEFM_RESTART_OFFSET;
+	u32 mask = DEFM_RESTART_MASK;
+	u32 buffer = 0;
+	u32 restart = 0;
+	void __iomem *working_address = ((u8 *)xroe_lp->base_addr
+	+ DEFM_RESTART_ADDR);
+
+	buffer = ioread32(working_address);
+	restart = (buffer & mask) >> offset;
+
+	if (restart)
+		sprintf(buff, "true\n");
+
+	else
+		sprintf(buff, "false\n");
+
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * deframer_restart_store - Writes to the deframer's restart status register
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the restart status
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the deframer's restart status
+ * to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t deframer_restart_store(struct kobject *kobj,
+				      struct kobj_attribute *attr,
+				      const char *buff, size_t count)
+{
+	u32 offset = DEFM_RESTART_OFFSET;
+	u32 mask = DEFM_RESTART_MASK;
+	void __iomem *working_address = ((u8 *)xroe_lp->base_addr
+	+ DEFM_RESTART_ADDR);
+	u32 restart = 0;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (strncmp(xroe_tmp, "true", xroe_size) == 0) {
+		restart = 0x01;
+		utils_write32withmask(working_address, restart,
+				      mask, offset);
+	} else if (strncmp(xroe_tmp, "false", xroe_size) == 0) {
+		restart = 0x00;
+		utils_write32withmask(working_address, restart,
+				      mask, offset);
+	}
+
+	return xroe_size;
+}
+
+/**
+ * xxv_reset_show - Returns the XXV's reset status
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the reset status
+ *
+ * Reads and writes the XXV's reset status to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t xxv_reset_show(struct kobject *kobj, struct kobj_attribute *attr,
+			      char *buff)
+{
+	u32 offset = CFG_USER_RW_OUT_OFFSET;
+	u32 mask = CFG_USER_RW_OUT_MASK;
+	u32 buffer = 0;
+	u32 restart = 0;
+	void __iomem *working_address = ((u8 *)xroe_lp->base_addr +
+	CFG_USER_RW_OUT_ADDR);
+
+	buffer = ioread32(working_address);
+	restart = (buffer & mask) >> offset;
+	if (restart)
+		sprintf(buff, "true\n");
+	else
+		sprintf(buff, "false\n");
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * xxv_reset_store - Writes to the XXV's reset register
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the reset status
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the XXV's reset status
+ * to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t xxv_reset_store(struct  kobject *kobj,
+			       struct kobj_attribute *attr,
+			       const char *buff, size_t count)
+{
+	u32 offset = CFG_USER_RW_OUT_OFFSET;
+	u32 mask = CFG_USER_RW_OUT_MASK;
+	void __iomem *working_address = ((u8 *)xroe_lp->base_addr +
+	CFG_USER_RW_OUT_ADDR);
+	u32 restart = 0;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+
+	if (strncmp(xroe_tmp, "true", xroe_size) == 0) {
+		restart = 0x01;
+		utils_write32withmask(working_address, restart,
+				      mask, offset);
+	} else if (strncmp(xroe_tmp, "false", xroe_size) == 0) {
+		restart = 0x00;
+		utils_write32withmask(working_address, restart,
+				      mask, offset);
+	}
+	return xroe_size;
+}
+
+/**
+ * framing_show - Returns the current framing
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the reset status
+ *
+ * Reads and writes the current framing type to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t framing_show(struct kobject *kobj, struct kobj_attribute *attr,
+			    char *buff)
+{
+	u32 offset = (DEFM_DATA_PKT_MESSAGE_TYPE_ADDR +
+	DEFM_DATA_PKT_MESSAGE_TYPE_OFFSET);
+	u8 buffer = 0;
+	u8 framing = 0xff;
+	void __iomem *working_address = ((u8 *)xroe_lp->base_addr + offset);
+
+	buffer = ioread8(working_address);
+	framing = buffer;
+	if (framing == 0)
+		sprintf(buff, "eCPRI\n");
+	else if (framing == 1)
+		sprintf(buff, "1914.3\n");
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * framing_store - Writes to the current framing register
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the reset status
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the current framing
+ * to the sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t framing_store(struct kobject *kobj, struct kobj_attribute *attr,
+			     const char *buff, size_t count)
+{
+	u32 offset = (DEFM_DATA_PKT_MESSAGE_TYPE_ADDR +
+	DEFM_DATA_PKT_MESSAGE_TYPE_OFFSET);
+	void __iomem *working_address = ((u8 *)xroe_lp->base_addr + offset);
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (strncmp(xroe_tmp, "eCPRI", xroe_size) == 0)
+		iowrite8(0, working_address);
+	else if (strncmp(xroe_tmp, "1914.3", xroe_size) == 0)
+		iowrite8(1, working_address);
+	return xroe_size;
+}
+
+/* TODO Use DEVICE_ATTR/_RW/_RO macros */
+
+static struct kobj_attribute version_attribute =
+	__ATTR(version, 0444, version_show, version_store);
+
+static struct kobj_attribute enable_attribute =
+	__ATTR(enable, 0660, enable_show, enable_store);
+
+static struct kobj_attribute framer_restart =
+	__ATTR(framer_restart, 0660, framer_restart_show, framer_restart_store);
+
+static struct kobj_attribute deframer_restart =
+	__ATTR(deframer_restart, 0660, deframer_restart_show,
+	       deframer_restart_store);
+
+static struct kobj_attribute xxv_reset =
+	__ATTR(xxv_reset, 0660, xxv_reset_show, xxv_reset_store);
+
+static struct kobj_attribute framing_attribute =
+	__ATTR(framing, 0660, framing_show, framing_store);
+
+static struct attribute *attrs[] = {
+	&version_attribute.attr,
+	&enable_attribute.attr,
+	&framer_restart.attr,
+	&deframer_restart.attr,
+	&xxv_reset.attr,
+	&framing_attribute.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+
+struct kobject *root_xroe_kobj;
+
+/**
+ * xroe_sysfs_init - Creates the xroe sysfs directory and entries
+ *
+ * Return: 0 on success, negative value in case of failure to
+ * create the sysfs group
+ *
+ * Creates the xroe sysfs directory and entries, as well as the
+ * subdirectories for IPv4, IPv6 & UDP
+ */
+int xroe_sysfs_init(void)
+{
+	int ret;
+
+	root_xroe_kobj = kobject_create_and_add("xroe", kernel_kobj);
+	if (!root_xroe_kobj)
+		return -ENOMEM;
+	ret = sysfs_create_group(root_xroe_kobj, &attr_group);
+	if (ret)
+		kobject_put(root_xroe_kobj);
+	ret = xroe_sysfs_ipv4_init();
+	if (ret)
+		return ret;
+	ret = xroe_sysfs_ipv6_init();
+	if (ret)
+		return ret;
+	ret = xroe_sysfs_udp_init();
+	if (ret)
+		return ret;
+	ret = xroe_sysfs_stats_init();
+	return ret;
+}
+
+/**
+ * xroe_sysfs_exit - Deletes the xroe sysfs directory and entries
+ *
+ * Deletes the xroe sysfs directory and entries, as well as the
+ * subdirectories for IPv4, IPv6 & UDP
+ *
+ */
+void xroe_sysfs_exit(void)
+{
+	int i;
+
+	xroe_sysfs_ipv4_exit();
+	xroe_sysfs_ipv6_exit();
+	xroe_sysfs_udp_exit();
+	xroe_sysfs_stats_exit();
+	for (i = 0; i < MAX_NUM_ETH_PORTS; i++)
+		kobject_put(kobj_eth_ports[i]);
+	kobject_put(kobj_framer);
+	kobject_put(root_xroe_kobj);
+}
+
+/**
+ * utils_write32withmask - Writes a masked 32-bit value
+ * @working_address:	The starting address to write
+ * @value:			The value to be written
+ * @mask:			The mask to be used
+ * @offset:			The offset from the provided starting address
+ *
+ * Writes a 32-bit value to the provided address with the input mask
+ *
+ * Return: 0 on success
+ */
+int utils_write32withmask(void __iomem *working_address, u32 value,
+			  u32 mask, u32 offset)
+{
+	u32 read_register_value = 0;
+	u32 register_value_to_write = 0;
+	u32 delta = 0, buffer = 0;
+
+	read_register_value = ioread32(working_address);
+	buffer = (value << offset);
+	register_value_to_write = read_register_value & ~mask;
+	delta = buffer & mask;
+	register_value_to_write |= delta;
+	iowrite32(register_value_to_write, working_address);
+	return 0;
+}
+
+/**
+ * utils_sysfs_path_to_eth_port_num - Get the current ethernet port
+ * @kobj:	The kobject of the entry calling the function
+ *
+ * Extracts the number of the current ethernet port instance
+ *
+ * Return: The number of the ethernet port instance (0 - MAX_NUM_ETH_PORTS) on
+ * success, -1 otherwise
+ */
+static int utils_sysfs_path_to_eth_port_num(struct kobject *kobj)
+{
+	char *current_path = NULL;
+	int port;
+	int ret;
+
+	current_path = kobject_get_path(kobj, GFP_KERNEL);
+	ret = sscanf(current_path, "/kernel/xroe/framer/eth_port_%d/", &port);
+	/* if sscanf() returns 0, no fields were assigned, therefore no
+	 * adjustments will be made for port number
+	 */
+	if (ret == 0)
+		port = 0;
+//	printk(KERN_ALERT "current_path: %s port: %d\n", current_path, port);
+	kfree(current_path);
+	return port;
+}
+
+/**
+ * utils_sysfs_store_wrapper - Wraps the storing function for sysfs entries
+ * @address:	The address of the register to be written
+ * @offset:	The offset from the address of the register
+ * @mask:	The mask to be used on the value to be written
+ * @value:	The value to be written to the register
+ * @kobj:	The kobject of the entry calling the function
+ *
+ * Wraps the core functionality of all "store" functions of sysfs entries.
+ * After calculating the ethernet port number (in N/A cases, it's 0), the value
+ * is written to the designated register
+ *
+ */
+void utils_sysfs_store_wrapper(u32 address, u32 offset, u32 mask, u32 value,
+			       struct kobject *kobj)
+{
+	int port;
+	void __iomem *working_address;
+
+	port = utils_sysfs_path_to_eth_port_num(kobj);
+	working_address = (void __iomem *)(xroe_lp->base_addr +
+			  (address + (0x100 * port)));
+	utils_write32withmask(working_address, value, mask, offset);
+}
+
+/**
+ * utils_sysfs_store_wrapper - Wraps the storing function for sysfs entries
+ * @address:	The address of the register to be read
+ * @offset:	The offset from the address of the register
+ * @mask:	The mask to be used on the value to be read
+ * @kobj:	The kobject of the entry calling the function
+ *
+ * Wraps the core functionality of all "show" functions of sysfs entries.
+ * After calculating the ethernet port number (in N/A cases, it's 0), the value
+ * is read from the designated register and returned.
+ *
+ * Return: The value designated by the address, offset and mask
+ */
+u32 utils_sysfs_show_wrapper(u32 address, u32 offset, u32 mask,
+			     struct kobject *kobj)
+{
+	int port;
+	void __iomem *working_address;
+	u32 buffer;
+
+	port = utils_sysfs_path_to_eth_port_num(kobj);
+	working_address = (void __iomem *)(xroe_lp->base_addr +
+			  (address + (0x100 * port)));
+	buffer = ioread32(working_address);
+	return (buffer & mask) >> offset;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/sysfs_xroe_framer_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/sysfs_xroe_framer_ipv4.c
@@ -0,0 +1,718 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "xroe_framer.h"
+
+enum { XROE_SIZE_MAX = 15 };
+static int xroe_size;
+static char xroe_tmp[XROE_SIZE_MAX];
+
+static void utils_ipv4addr_hextochar(u32 ip, unsigned char *bytes);
+static int utils_ipv4addr_chartohex(char *ip_addr, uint32_t *p_ip_addr);
+
+/**
+ * ipv4_version_show - Returns the IPv4 version number
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 version number
+ *
+ * Returns the IPv4 version number
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_version_show(struct kobject *kobj,
+				 struct kobj_attribute *attr, char *buff)
+{
+	u32 version;
+
+	version = utils_sysfs_show_wrapper(ETH_IPV4_VERSION_ADDR,
+					   ETH_IPV4_VERSION_OFFSET,
+					   ETH_IPV4_VERSION_MASK, kobj);
+	sprintf(buff, "%d\n", version);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_version_store - Writes to the IPv4 version number sysfs entry
+ * (not permitted)
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 version
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 version number sysfs entry (not permitted)
+ *
+ * Return: 0
+ */
+static ssize_t ipv4_version_store(struct kobject *kobj,
+				  struct kobj_attribute *attr, const char *buff,
+				  size_t count)
+{
+	return 0;
+}
+
+/**
+ * ipv4_ihl_show - Returns the IPv4 IHL
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 IHL
+ *
+ * Returns the IPv4 IHL
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_ihl_show(struct kobject *kobj,
+			     struct kobj_attribute *attr, char *buff)
+{
+	u32 ihl;
+
+	ihl = utils_sysfs_show_wrapper(ETH_IPV4_IHL_ADDR, ETH_IPV4_IHL_OFFSET,
+				       ETH_IPV4_IHL_MASK, kobj);
+	sprintf(buff, "%d\n", ihl);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_ihl_store - Writes to the IPv4 IHL sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 IHL
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 IHL sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_ihl_store(struct kobject *kobj,
+			      struct kobj_attribute *attr, const char *buff,
+			      size_t count)
+{
+	int ret;
+	u32 ihl;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &ihl);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_IHL_ADDR, ETH_IPV4_IHL_OFFSET,
+				  ETH_IPV4_IHL_MASK, ihl, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_dscp_show - Returns the IPv4 DSCP
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 DSCP
+ *
+ * Returns the IPv4 DSCP
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_dscp_show(struct kobject *kobj,
+			      struct kobj_attribute *attr, char *buff)
+{
+	u32 dscp;
+
+	dscp = utils_sysfs_show_wrapper(ETH_IPV4_DSCP_ADDR,
+					ETH_IPV4_DSCP_OFFSET,
+					ETH_IPV4_DSCP_MASK, kobj);
+	sprintf(buff, "%d\n", dscp);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_dscp_store - Writes to the IPv4 DSCP sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 DSCP
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 DSCP sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_dscp_store(struct kobject *kobj,
+			       struct kobj_attribute *attr, const char *buff,
+			       size_t count)
+{
+	int ret;
+	u32 dscp;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &dscp);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_DSCP_ADDR, ETH_IPV4_DSCP_OFFSET,
+				  ETH_IPV4_DSCP_MASK, dscp, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_ecn_show - Returns the IPv4 ECN
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 ECN
+ *
+ * Returns the IPv4 ECN
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_ecn_show(struct kobject *kobj,
+			     struct kobj_attribute *attr, char *buff)
+{
+	u32 ecn;
+
+	ecn = utils_sysfs_show_wrapper(ETH_IPV4_ECN_ADDR, ETH_IPV4_ECN_OFFSET,
+				       ETH_IPV4_ECN_MASK, kobj);
+	sprintf(buff, "%d\n", ecn);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_ecn_store - Writes to the IPv4 ECN sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 ECN
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 ECN sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_ecn_store(struct kobject *kobj,
+			      struct kobj_attribute *attr, const char *buff,
+			      size_t count)
+{
+	int ret;
+	u32 ecn;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &ecn);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_ECN_ADDR, ETH_IPV4_ECN_OFFSET,
+				  ETH_IPV4_ECN_MASK, ecn, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_id_show - Returns the IPv4 ID
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 ID
+ *
+ * Returns the IPv4 ID
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_id_show(struct kobject *kobj,
+			    struct kobj_attribute *attr, char *buff)
+{
+	u32 id;
+
+	id = utils_sysfs_show_wrapper(ETH_IPV4_ID_ADDR, ETH_IPV4_ID_OFFSET,
+				      ETH_IPV4_ID_MASK, kobj);
+	sprintf(buff, "%d\n", id);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_id_store - Writes to the IPv4 ID sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 ID
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 ID sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_id_store(struct kobject *kobj,
+			     struct kobj_attribute *attr, const char *buff,
+			     size_t count)
+{
+	int ret;
+	u32 id;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &id);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_ID_ADDR, ETH_IPV4_ID_OFFSET,
+				  ETH_IPV4_ID_MASK, id, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_flags_show - Returns the IPv4 flags
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 flags
+ *
+ * Returns the IPv4 flags
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_flags_show(struct kobject *kobj,
+			       struct kobj_attribute *attr, char *buff)
+{
+	u32 flags;
+
+	flags = utils_sysfs_show_wrapper(ETH_IPV4_FLAGS_ADDR,
+					 ETH_IPV4_FLAGS_OFFSET,
+					 ETH_IPV4_FLAGS_MASK, kobj);
+	sprintf(buff, "%d\n", flags);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_flags_store - Writes to the IPv4 flags sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 flags
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 flags sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_flags_store(struct kobject *kobj,
+				struct kobj_attribute *attr, const char *buff,
+				size_t count)
+{
+	int ret;
+	u32 flags;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &flags);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_FLAGS_ADDR, ETH_IPV4_FLAGS_OFFSET,
+				  ETH_IPV4_FLAGS_MASK, flags, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_fragment_offset_show - Returns the IPv4 fragment offset
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 fragment offset
+ *
+ * Returns the IPv4 fragment offset
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_fragment_offset_show
+(struct kobject *kobj, struct kobj_attribute *attr, char *buff)
+{
+	u32 fragment;
+
+	fragment = utils_sysfs_show_wrapper(ETH_IPV4_FRAGMENT_OFFSET_ADDR,
+					    ETH_IPV4_FRAGMENT_OFFSET_OFFSET,
+					    ETH_IPV4_FRAGMENT_OFFSET_MASK,
+					    kobj);
+	sprintf(buff, "%d\n", fragment);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_fragment_offset_store - Writes to the IPv4 fragment offset sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 fragment offset
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 fragment offset sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_fragment_offset_store
+(struct kobject *kobj, struct kobj_attribute *attr, const char *buff,
+size_t count)
+{
+	int ret;
+	u32 fragment;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &fragment);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_FRAGMENT_OFFSET_ADDR,
+				  ETH_IPV4_FRAGMENT_OFFSET_OFFSET,
+				  ETH_IPV4_FRAGMENT_OFFSET_MASK, fragment,
+				  kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_ttl_show - Returns the IPv4 TTL
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 TTL
+ *
+ * Returns the IPv4 TTL
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_ttl_show(struct kobject *kobj, struct kobj_attribute *attr,
+			     char *buff)
+{
+	u32 ttl;
+
+	ttl = utils_sysfs_show_wrapper(ETH_IPV4_TIME_TO_LIVE_ADDR,
+				       ETH_IPV4_TIME_TO_LIVE_OFFSET,
+				       ETH_IPV4_TIME_TO_LIVE_MASK, kobj);
+	sprintf(buff, "%d\n", ttl);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_ttl_store - Writes to the IPv4 TTL sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 TTL
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 TTL sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_ttl_store(struct kobject *kobj,
+			      struct kobj_attribute *attr, const char *buff,
+			      size_t count)
+{
+	int ret;
+	u32 ttl;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &ttl);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_TIME_TO_LIVE_ADDR,
+				  ETH_IPV4_TIME_TO_LIVE_OFFSET,
+				  ETH_IPV4_TIME_TO_LIVE_MASK, ttl, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_protocol_show - Returns the IPv4 protocol
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 protocol
+ *
+ * Returns the IPv4 protocol
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_protocol_show(struct kobject *kobj,
+				  struct kobj_attribute *attr, char *buff)
+{
+	u32 protocol;
+
+	protocol = utils_sysfs_show_wrapper(ETH_IPV4_PROTOCOL_ADDR,
+					    ETH_IPV4_PROTOCOL_OFFSET,
+					    ETH_IPV4_PROTOCOL_MASK, kobj);
+	sprintf(buff, "%d\n", protocol);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_protocol_store - Writes to the IPv4 protocol sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 protocol
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 protocol sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_protocol_store(struct kobject *kobj,
+				   struct kobj_attribute *attr,
+				   const char *buff, size_t count)
+{
+	int ret;
+	u32 protocol;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &protocol);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV4_PROTOCOL_ADDR,
+				  ETH_IPV4_PROTOCOL_OFFSET,
+				  ETH_IPV4_PROTOCOL_MASK, protocol, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_source_address_show - Returns the IPv4 source address
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 source address
+ *
+ * Returns the IPv4 source address in x.x.x.x format
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_source_address_show
+(struct kobject *kobj, struct kobj_attribute *attr, char *buff)
+{
+	u32 source_add = 0;
+	unsigned char ip_addr_char[4];
+
+	source_add = utils_sysfs_show_wrapper(ETH_IPV4_SOURCE_ADD_ADDR,
+					      ETH_IPV4_SOURCE_ADD_OFFSET,
+					      ETH_IPV4_SOURCE_ADD_MASK, kobj);
+	utils_ipv4addr_hextochar(source_add, ip_addr_char);
+	sprintf(buff, "%d.%d.%d.%d\n", ip_addr_char[3], ip_addr_char[2],
+		ip_addr_char[1], ip_addr_char[0]);
+
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_source_address_store - Writes to the IPv4 source address sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 source address
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 source address sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_source_address_store
+(struct kobject *kobj, struct kobj_attribute *attr, const char *buff,
+size_t count)
+{
+	u32 source_add = 0;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (utils_ipv4addr_chartohex(xroe_tmp, &source_add) == 4)
+		utils_sysfs_store_wrapper(ETH_IPV4_SOURCE_ADD_ADDR,
+					  ETH_IPV4_SOURCE_ADD_OFFSET,
+					  ETH_IPV4_SOURCE_ADD_MASK, source_add,
+					  kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv4_destination_address_show - Returns the IPv4 destination address
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 destination address
+ *
+ * Returns the IPv4 destination address in x.x.x.x format
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv4_destination_address_show
+(struct kobject *kobj, struct kobj_attribute *attr, char *buff)
+{
+	u32 dest_add = 0;
+	unsigned char ip_addr_char[4];
+
+	dest_add = utils_sysfs_show_wrapper(ETH_IPV4_DESTINATION_ADD_ADDR,
+					    ETH_IPV4_DESTINATION_ADD_OFFSET,
+					    ETH_IPV4_DESTINATION_ADD_MASK,
+					    kobj);
+	utils_ipv4addr_hextochar(dest_add, ip_addr_char);
+	sprintf(buff, "%d.%d.%d.%d\n", ip_addr_char[3], ip_addr_char[2],
+		ip_addr_char[1], ip_addr_char[0]);
+
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv4_destination_address_store - Writes to the IPv4 destination address
+ * sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 destination address
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv4 destination address sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv4_destination_address_store
+(struct kobject *kobj, struct kobj_attribute *attr, const char *buff,
+size_t count)
+{
+	u32 dest_add = 0;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (utils_ipv4addr_chartohex(xroe_tmp, &dest_add) == 4)
+		utils_sysfs_store_wrapper(ETH_IPV4_DESTINATION_ADD_ADDR,
+					  ETH_IPV4_DESTINATION_ADD_OFFSET,
+					  ETH_IPV4_DESTINATION_ADD_MASK,
+					  dest_add, kobj);
+	return xroe_size;
+}
+
+/* TODO Use DEVICE_ATTR/_RW/_RO macros */
+
+static struct kobj_attribute version_attribute =
+	__ATTR(version, 0444, ipv4_version_show, ipv4_version_store);
+static struct kobj_attribute ihl_attribute =
+	__ATTR(ihl, 0660, ipv4_ihl_show, ipv4_ihl_store);
+static struct kobj_attribute dscp_attribute =
+	__ATTR(dscp, 0660, ipv4_dscp_show, ipv4_dscp_store);
+static struct kobj_attribute ecn_attribute =
+	__ATTR(ecn, 0660, ipv4_ecn_show, ipv4_ecn_store);
+static struct kobj_attribute id_attribute =
+	__ATTR(id, 0660, ipv4_id_show, ipv4_id_store);
+static struct kobj_attribute flags_attribute =
+	__ATTR(flags, 0660, ipv4_flags_show, ipv4_flags_store);
+static struct kobj_attribute fragment_offset_attribute =
+	__ATTR(fragment_offset, 0660, ipv4_fragment_offset_show,
+	       ipv4_fragment_offset_store);
+static struct kobj_attribute ttl_attribute =
+	__ATTR(ttl, 0660, ipv4_ttl_show, ipv4_ttl_store);
+static struct kobj_attribute protocol_attribute =
+	__ATTR(protocol, 0660, ipv4_protocol_show, ipv4_protocol_store);
+static struct kobj_attribute source_add_attribute =
+	__ATTR(source_add, 0660, ipv4_source_address_show,
+	       ipv4_source_address_store);
+static struct kobj_attribute destination_add_attribute =
+	__ATTR(dest_add, 0660, ipv4_destination_address_show,
+	       ipv4_destination_address_store);
+
+static struct attribute *attrs[] = {
+	&version_attribute.attr,
+	&ihl_attribute.attr,
+	&dscp_attribute.attr,
+	&ecn_attribute.attr,
+	&id_attribute.attr,
+	&flags_attribute.attr,
+	&fragment_offset_attribute.attr,
+	&ttl_attribute.attr,
+	&protocol_attribute.attr,
+	&source_add_attribute.attr,
+	&destination_add_attribute.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+
+struct kobject *kobj_framer;
+static struct kobject *kobj_ipv4[MAX_NUM_ETH_PORTS];
+struct kobject *kobj_eth_ports[MAX_NUM_ETH_PORTS];
+
+/**
+ * xroe_sysfs_ipv4_init - Creates the xroe sysfs "ipv4" subdirectory & entries
+ *
+ * Return: 0 on success, negative value in case of failure to
+ * create the sysfs group
+ *
+ * Creates the xroe sysfs "ipv4" subdirectory and entries under "xroe"
+ */
+int xroe_sysfs_ipv4_init(void)
+{
+	int ret;
+	int i;
+	char eth_port_dir_name[11];
+
+	kobj_framer = kobject_create_and_add("framer", root_xroe_kobj);
+	if (!kobj_framer)
+		return -ENOMEM;
+	for (i = 0; i < 4; i++) {
+		snprintf(eth_port_dir_name, sizeof(eth_port_dir_name),
+			 "eth_port_%d", i);
+		kobj_eth_ports[i] = kobject_create_and_add(eth_port_dir_name,
+							   kobj_framer);
+		if (!kobj_eth_ports[i])
+			return -ENOMEM;
+		kobj_ipv4[i] = kobject_create_and_add("ipv4",
+						      kobj_eth_ports[i]);
+		if (!kobj_ipv4[i])
+			return -ENOMEM;
+		ret = sysfs_create_group(kobj_ipv4[i], &attr_group);
+		if (ret)
+			kobject_put(kobj_ipv4[i]);
+	}
+	return ret;
+}
+
+/**
+ * xroe_sysfs_ipv4_exit - Deletes the xroe sysfs "ipv4" subdirectory & entries
+ *
+ * Deletes the xroe sysfs "ipv4" subdirectory and entries,
+ * under the "xroe" entry
+ */
+void xroe_sysfs_ipv4_exit(void)
+{
+	int i;
+
+	for (i = 0; i < MAX_NUM_ETH_PORTS; i++)
+		kobject_put(kobj_ipv4[i]);
+}
+
+/**
+ * utils_ipv4addr_hextochar - Integer to char array for IPv4 addresses
+ * @ip:		The IP address in integer format
+ * @bytes:	The IP address in a 4-byte array
+ *
+ * Coverts an IPv4 address given in unsigned integer format to a character array
+ */
+static void utils_ipv4addr_hextochar(u32 ip, unsigned char *bytes)
+{
+	bytes[0] = ip & 0xFF;
+	bytes[1] = (ip >> 8) & 0xFF;
+	bytes[2] = (ip >> 16) & 0xFF;
+	bytes[3] = (ip >> 24) & 0xFF;
+}
+
+/**
+ * utils_ipv4addr_chartohex - Character to char array for IPv4 addresses
+ * @ip_addr:	The character array containing the IP address
+ * @p_ip_addr:	The converted IPv4 address
+ *
+ * Coverts an IPv4 address given as a character array to integer format
+ *
+ * Return: 4 (the length of the resulting character array) on success,
+ * -1 in case of wrong input
+ */
+static int utils_ipv4addr_chartohex(char *ip_addr, uint32_t *p_ip_addr)
+{
+	int count = 0, ret = -1;
+	char *string;
+	unsigned char *found;
+	u32 byte_array[4];
+	u32 byte = 0;
+
+	string = ip_addr;
+	while ((found = (unsigned char *)strsep(&string, ".")) != NULL) {
+		if (count <= 4) {
+			ret = kstrtouint(found, 10, &byte);
+			if (ret)
+				return ret;
+			byte_array[count] = byte;
+		} else {
+			break;
+		}
+		count++;
+	}
+
+	if (count == 4) {
+		ret = count;
+		*p_ip_addr = byte_array[3] | (byte_array[2] << 8)
+		| (byte_array[1] << 16) | (byte_array[0] << 24);
+	}
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/sysfs_xroe_framer_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/sysfs_xroe_framer_ipv6.c
@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "xroe_framer.h"
+
+enum { XROE_SIZE_MAX = 60 };
+static int xroe_size;
+static char xroe_tmp[XROE_SIZE_MAX];
+
+static void utils_ipv6addr_32to16(u32 *ip32, uint16_t *ip16);
+static int utils_ipv6addr_chartohex(char *ip_addr, uint32_t *p_ip_addr);
+
+/**
+ * ipv6_version_show - Returns the IPv6 version number
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 version number
+ *
+ * Returns the IPv6 version number
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_version_show(struct kobject *kobj,
+				 struct kobj_attribute *attr, char *buff)
+{
+	u32 version;
+
+	version = utils_sysfs_show_wrapper(ETH_IPV6_V_ADDR, ETH_IPV6_V_OFFSET,
+					   ETH_IPV6_V_MASK, kobj);
+	sprintf(buff, "%d\n", version);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_version_store - Writes to the IPv6 version number sysfs entry
+ * (not permitted)
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 version
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 version number sysfs entry (not permitted)
+ *
+ * Return: 0
+ */
+static ssize_t ipv6_version_store(struct kobject *kobj,
+				  struct kobj_attribute *attr,
+				  const char *buff, size_t count)
+{
+	return 0;
+}
+
+/**
+ * ipv6_traffic_class_show - Returns the IPv6 traffic class
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 traffic class
+ *
+ * Returns the IPv6 traffic class
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_traffic_class_show(struct kobject *kobj,
+				       struct kobj_attribute *attr, char *buff)
+{
+	u32 traffic_class;
+
+	traffic_class = utils_sysfs_show_wrapper(ETH_IPV6_TRAFFIC_CLASS_ADDR,
+						 ETH_IPV6_TRAFFIC_CLASS_OFFSET,
+						 ETH_IPV6_TRAFFIC_CLASS_MASK,
+						 kobj);
+	sprintf(buff, "%d\n", traffic_class);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_traffic_class_store - Writes to the IPv6 traffic class
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 traffic class
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 traffic class sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv6_traffic_class_store(struct kobject *kobj,
+					struct kobj_attribute *attr,
+					const char *buff, size_t count)
+{
+	int ret;
+	u32 traffic_class;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &traffic_class);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV6_TRAFFIC_CLASS_ADDR,
+				  ETH_IPV6_TRAFFIC_CLASS_OFFSET,
+				  ETH_IPV6_TRAFFIC_CLASS_MASK, traffic_class,
+				  kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv6_flow_label_show - Returns the IPv6 flow label
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 flow label
+ *
+ * Returns the IPv6 flow label
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_flow_label_show(struct kobject *kobj,
+				    struct kobj_attribute *attr, char *buff)
+{
+	u32 flow_label;
+
+	flow_label = utils_sysfs_show_wrapper(ETH_IPV6_FLOW_LABEL_ADDR,
+					      ETH_IPV6_FLOW_LABEL_OFFSET,
+					      ETH_IPV6_FLOW_LABEL_MASK, kobj);
+	sprintf(buff, "%d\n", flow_label);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_flow_label_store - Writes to the IPv6 flow label
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 flow label
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 flow label sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv6_flow_label_store(struct kobject *kobj,
+				     struct kobj_attribute *attr,
+				     const char *buff, size_t count)
+{
+	int ret;
+	u32 flow_label;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &flow_label);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV6_FLOW_LABEL_ADDR,
+				  ETH_IPV6_FLOW_LABEL_OFFSET,
+				  ETH_IPV6_FLOW_LABEL_MASK, flow_label, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv6_next_header_show - Returns the IPv6 next header
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 next header
+ *
+ * Returns the IPv6 next header
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_next_header_show(struct kobject *kobj,
+				     struct kobj_attribute *attr,
+				     char *buff)
+{
+	u32 next_header;
+
+	next_header = utils_sysfs_show_wrapper(ETH_IPV6_NEXT_HEADER_ADDR,
+					       ETH_IPV6_NEXT_HEADER_OFFSET,
+					       ETH_IPV6_NEXT_HEADER_MASK, kobj);
+	sprintf(buff, "%d\n", next_header);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_next_header_store - Writes to the IPv6 next header
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 next header
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 next header sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv6_next_header_store(struct kobject *kobj,
+				      struct kobj_attribute *attr,
+				      const char *buff, size_t count)
+{
+	int ret;
+	u32 next_header;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &next_header);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV6_NEXT_HEADER_ADDR,
+				  ETH_IPV6_NEXT_HEADER_OFFSET,
+				  ETH_IPV6_NEXT_HEADER_MASK, next_header, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv6_hop_limit_show - Returns the IPv6 hop limit
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 hop limit
+ *
+ * Returns the IPv6 hop limit
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_hop_limit_show(struct kobject *kobj,
+				   struct kobj_attribute *attr, char *buff)
+{
+	u32 hop_limit;
+
+	hop_limit = utils_sysfs_show_wrapper(ETH_IPV6_HOP_LIMIT_ADDR,
+					     ETH_IPV6_HOP_LIMIT_OFFSET,
+					     ETH_IPV6_HOP_LIMIT_MASK, kobj);
+	sprintf(buff, "%d\n", hop_limit);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_hop_limit_store - Writes to the IPv6 hop limit
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv6 hop limit
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 hop limit sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv6_hop_limit_store
+(struct kobject *kobj, struct kobj_attribute *attr, const char *buff,
+size_t count)
+{
+	int ret;
+	u32 hop_limit;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &hop_limit);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_IPV6_HOP_LIMIT_ADDR,
+				  ETH_IPV6_HOP_LIMIT_OFFSET,
+				  ETH_IPV6_HOP_LIMIT_MASK, hop_limit, kobj);
+	return xroe_size;
+}
+
+/**
+ * ipv6_source_address_show - Returns the IPv6 source address
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 source address
+ *
+ * Returns the IPv6 source address in xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx
+ * format
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_source_address_show
+(struct kobject *kobj, struct kobj_attribute *attr, char *buff)
+{
+	u32 source[4];
+	u16 source_add16[8];
+
+	source[0] = utils_sysfs_show_wrapper(ETH_IPV6_SOURCE_ADD_31_0_ADDR,
+					     ETH_IPV6_SOURCE_ADD_31_0_OFFSET,
+					     ETH_IPV6_SOURCE_ADD_31_0_MASK,
+					     kobj);
+	source[1] = utils_sysfs_show_wrapper(ETH_IPV6_SOURCE_ADD_63_32_ADDR,
+					     ETH_IPV6_SOURCE_ADD_63_32_OFFSET,
+					     ETH_IPV6_SOURCE_ADD_63_32_MASK,
+					     kobj);
+	source[2] = utils_sysfs_show_wrapper(ETH_IPV6_SOURCE_ADD_95_64_ADDR,
+					     ETH_IPV6_SOURCE_ADD_95_64_OFFSET,
+					     ETH_IPV6_SOURCE_ADD_95_64_MASK,
+					     kobj);
+	source[3] = utils_sysfs_show_wrapper(ETH_IPV6_SOURCE_ADD_127_96_ADDR,
+					     ETH_IPV6_SOURCE_ADD_127_96_OFFSET,
+					     ETH_IPV6_SOURCE_ADD_127_96_MASK,
+					     kobj);
+
+	utils_ipv6addr_32to16(source, source_add16);
+	sprintf(buff, "%04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x\n",
+		source_add16[0], source_add16[1], source_add16[2],
+		source_add16[3],
+		source_add16[4], source_add16[5], source_add16[6],
+		source_add16[7]);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_source_address_store - Writes to the IPv6 source address sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 source address
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 source address sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv6_source_address_store
+(struct kobject *kobj, struct kobj_attribute *attr, const char *buff,
+size_t count)
+{
+	u32 source_add[4];
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (utils_ipv6addr_chartohex(xroe_tmp, source_add) == 8) {
+		utils_sysfs_store_wrapper(ETH_IPV6_SOURCE_ADD_31_0_ADDR,
+					  ETH_IPV6_SOURCE_ADD_31_0_OFFSET,
+					  ETH_IPV6_SOURCE_ADD_31_0_MASK,
+					  source_add[0], kobj);
+		utils_sysfs_store_wrapper(ETH_IPV6_SOURCE_ADD_63_32_ADDR,
+					  ETH_IPV6_SOURCE_ADD_63_32_OFFSET,
+					  ETH_IPV6_SOURCE_ADD_63_32_MASK,
+					  source_add[1], kobj);
+		utils_sysfs_store_wrapper(ETH_IPV6_SOURCE_ADD_95_64_ADDR,
+					  ETH_IPV6_SOURCE_ADD_95_64_OFFSET,
+					  ETH_IPV6_SOURCE_ADD_95_64_MASK,
+					  source_add[2], kobj);
+		utils_sysfs_store_wrapper(ETH_IPV6_SOURCE_ADD_127_96_ADDR,
+					  ETH_IPV6_SOURCE_ADD_127_96_OFFSET,
+					  ETH_IPV6_SOURCE_ADD_127_96_MASK,
+					  source_add[3], kobj);
+	}
+	return xroe_size;
+}
+
+/**
+ * ipv6_destination_address_show - Returns the IPv6 destination address
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 destination address
+ *
+ * Returns the IPv6 destination address in
+ * xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx format
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t ipv6_destination_address_show
+(struct kobject *kobj, struct kobj_attribute *attr, char *buff)
+{
+	u32 dest[4];
+	u16 dest_add16[8];
+
+	dest[0] = utils_sysfs_show_wrapper(ETH_IPV6_DEST_ADD_31_0_ADDR,
+					   ETH_IPV6_DEST_ADD_31_0_OFFSET,
+					   ETH_IPV6_DEST_ADD_31_0_MASK,
+					   kobj);
+	dest[1] = utils_sysfs_show_wrapper(ETH_IPV6_DEST_ADD_63_32_ADDR,
+					   ETH_IPV6_DEST_ADD_63_32_OFFSET,
+					   ETH_IPV6_DEST_ADD_63_32_MASK,
+					   kobj);
+	dest[2] = utils_sysfs_show_wrapper(ETH_IPV6_DEST_ADD_95_64_ADDR,
+					   ETH_IPV6_DEST_ADD_95_64_OFFSET,
+					   ETH_IPV6_DEST_ADD_95_64_MASK,
+					   kobj);
+	dest[3] = utils_sysfs_show_wrapper(ETH_IPV6_DEST_ADD_127_96_ADDR,
+					   ETH_IPV6_DEST_ADD_127_96_OFFSET,
+					   ETH_IPV6_DEST_ADD_127_96_MASK,
+					   kobj);
+
+	utils_ipv6addr_32to16(dest, dest_add16);
+	sprintf(buff, "%04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x\n",
+		dest_add16[0], dest_add16[1], dest_add16[2],
+		dest_add16[3],
+		dest_add16[4], dest_add16[5], dest_add16[6],
+		dest_add16[7]);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * ipv6_destination_address_store - Writes to the IPv6 destination address
+ * sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the IPv4 destination address
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the IPv6 destination address sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t ipv6_destination_address_store
+(struct kobject *kobj, struct kobj_attribute *attr, const char *buff,
+size_t count)
+{
+	u32 dest_add[4];
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	strncpy(xroe_tmp, buff, xroe_size);
+	if (utils_ipv6addr_chartohex(xroe_tmp, dest_add) == 8) {
+		utils_sysfs_store_wrapper(ETH_IPV6_DEST_ADD_31_0_ADDR,
+					  ETH_IPV6_DEST_ADD_31_0_OFFSET,
+					  ETH_IPV6_DEST_ADD_31_0_MASK,
+					  dest_add[0], kobj);
+		utils_sysfs_store_wrapper(ETH_IPV6_DEST_ADD_63_32_ADDR,
+					  ETH_IPV6_DEST_ADD_63_32_OFFSET,
+					  ETH_IPV6_DEST_ADD_63_32_MASK,
+					  dest_add[1], kobj);
+		utils_sysfs_store_wrapper(ETH_IPV6_DEST_ADD_95_64_ADDR,
+					  ETH_IPV6_DEST_ADD_95_64_OFFSET,
+					  ETH_IPV6_DEST_ADD_95_64_MASK,
+					  dest_add[2], kobj);
+		utils_sysfs_store_wrapper(ETH_IPV6_DEST_ADD_127_96_ADDR,
+					  ETH_IPV6_DEST_ADD_127_96_OFFSET,
+					  ETH_IPV6_DEST_ADD_127_96_MASK,
+					  dest_add[3], kobj);
+	}
+	return xroe_size;
+}
+
+/* TODO Use DEVICE_ATTR/_RW/_RO macros */
+
+static struct kobj_attribute version_attribute =
+	__ATTR(version, 0444, ipv6_version_show, ipv6_version_store);
+static struct kobj_attribute traffic_class =
+	__ATTR(traffic_class, 0660, ipv6_traffic_class_show,
+	       ipv6_traffic_class_store);
+static struct kobj_attribute flow_label =
+	__ATTR(flow_label, 0660, ipv6_flow_label_show, ipv6_flow_label_store);
+static struct kobj_attribute next_header =
+	__ATTR(next_header, 0660, ipv6_next_header_show,
+	       ipv6_next_header_store);
+static struct kobj_attribute hop_limit =
+	__ATTR(hop_limit, 0660, ipv6_hop_limit_show, ipv6_hop_limit_store);
+static struct kobj_attribute source_add_attribute =
+	__ATTR(source_add, 0660, ipv6_source_address_show,
+	       ipv6_source_address_store);
+static struct kobj_attribute dest_add_attribute =
+	__ATTR(dest_add, 0660, ipv6_destination_address_show,
+	       ipv6_destination_address_store);
+
+static struct attribute *attrs[] = {
+	&version_attribute.attr,
+	&traffic_class.attr,
+	&flow_label.attr,
+	&next_header.attr,
+	&hop_limit.attr,
+	&source_add_attribute.attr,
+	&dest_add_attribute.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+
+static struct kobject *kobj_ipv6[MAX_NUM_ETH_PORTS];
+
+/**
+ * xroe_sysfs_ipv6_init - Creates the xroe sysfs "ipv6" subdirectory & entries
+ *
+ * Return: 0 on success, negative value in case of failure to
+ * create the sysfs group
+ *
+ * Creates the xroe sysfs "ipv6" subdirectory and entries under "xroe"
+ */
+int xroe_sysfs_ipv6_init(void)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		kobj_ipv6[i] = kobject_create_and_add("ipv6",
+						      kobj_eth_ports[i]);
+		if (!kobj_ipv6[i])
+			return -ENOMEM;
+		ret = sysfs_create_group(kobj_ipv6[i], &attr_group);
+		if (ret)
+			kobject_put(kobj_ipv6[i]);
+	}
+	return ret;
+}
+
+/**
+ * xroe_sysfs_ipv4_exit - Deletes the xroe sysfs "ipv6" subdirectory & entries
+ *
+ * Deletes the xroe sysfs "ipv6" subdirectory and entries,
+ * under the "xroe" entry
+ *
+ */
+void xroe_sysfs_ipv6_exit(void)
+{
+	int i;
+
+	for (i = 0; i < MAX_NUM_ETH_PORTS; i++)
+		kobject_put(kobj_ipv6[i]);
+}
+
+/**
+ * utils_ipv6addr_32to16 - uint32_t to uint16_t for IPv6 addresses
+ * @ip32:	The IPv6 address in uint32_t format
+ * @ip16:	The IPv6 address in uint16_t format
+ *
+ * Coverts an IPv6 address given in uint32_t format to uint16_t
+ */
+static void utils_ipv6addr_32to16(u32 *ip32, uint16_t *ip16)
+{
+	ip16[0] = ip32[0] >> 16;
+	ip16[1] = ip32[0] & 0x0000FFFF;
+	ip16[2] = ip32[1] >> 16;
+	ip16[3] = ip32[1] & 0x0000FFFF;
+	ip16[4] = ip32[2] >> 16;
+	ip16[5] = ip32[2] & 0x0000FFFF;
+	ip16[6] = ip32[3] >> 16;
+	ip16[7] = ip32[3] & 0x0000FFFF;
+}
+
+/**
+ * utils_ipv6addr_chartohex - Character to char array for IPv6 addresses
+ * @ip_addr:	The character array containing the IP address
+ * @p_ip_addr:	The converted IPv4 address
+ *
+ * Coverts an IPv6 address given as a character array to integer format
+ *
+ * Return: 8 (the length of the resulting character array) on success,
+ * -1 in case of wrong input
+ */
+static int utils_ipv6addr_chartohex(char *ip_addr, uint32_t *p_ip_addr)
+{
+	int ret;
+	int count;
+	char *string;
+	unsigned char *found;
+	u16 ip_array_16[8];
+	u32 field;
+
+	ret = -1;
+	count = 0;
+	string = ip_addr;
+	while ((found = (unsigned char *)strsep(&string, ":")) != NULL) {
+		if (count <= 8) {
+			ret = kstrtouint(found, 16, &field);
+			if (ret)
+				return ret;
+			ip_array_16[count] = (uint16_t)field;
+		} else {
+			break;
+		}
+		count++;
+	}
+	if (count == 8) {
+		p_ip_addr[0] = ip_array_16[1] | (ip_array_16[0] << 16);
+		p_ip_addr[1] = ip_array_16[3] | (ip_array_16[2] << 16);
+		p_ip_addr[2] = ip_array_16[5] | (ip_array_16[4] << 16);
+		p_ip_addr[3] = ip_array_16[7] | (ip_array_16[6] << 16);
+		ret = count;
+	}
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/sysfs_xroe_framer_stats.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/sysfs_xroe_framer_stats.c
@@ -0,0 +1,401 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "xroe_framer.h"
+
+/**
+ * total_rx_good_pkt_show - Returns the total good rx packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total good rx packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_good_pkt_show(struct kobject *kobj,
+				      struct kobj_attribute *attr, char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_TOTAL_RX_GOOD_PKT_CNT_ADDR,
+					 STATS_TOTAL_RX_GOOD_PKT_CNT_OFFSET,
+					 STATS_TOTAL_RX_GOOD_PKT_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_bad_pkt_show - Returns the total bad rx packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total bad rx packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_bad_pkt_show(struct kobject *kobj,
+				     struct kobj_attribute *attr, char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_TOTAL_RX_BAD_PKT_CNT_ADDR,
+					 STATS_TOTAL_RX_BAD_PKT_CNT_OFFSET,
+					 STATS_TOTAL_RX_BAD_PKT_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_bad_fcs_show - Returns the total bad fcs count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total bad frame check sequences count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_bad_fcs_show(struct kobject *kobj,
+				     struct kobj_attribute *attr,
+				     char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_TOTAL_RX_BAD_FCS_CNT_ADDR,
+					 STATS_TOTAL_RX_BAD_FCS_CNT_OFFSET,
+					 STATS_TOTAL_RX_BAD_FCS_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_user_pkt_show - Returns the total user rx packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total user rx packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_user_pkt_show(struct kobject *kobj,
+				      struct kobj_attribute *attr,
+				      char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_DATA_RX_PACKETS_CNT_ADDR,
+					 STATS_USER_DATA_RX_PACKETS_CNT_OFFSET,
+					 STATS_USER_DATA_RX_PACKETS_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_good_user_pkt_show - Returns the total good user rx packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total good user rx packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_good_user_pkt_show(struct kobject *kobj,
+					   struct kobj_attribute *attr,
+					   char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_DATA_RX_GOOD_PKT_CNT_ADDR,
+					 STATS_USER_DATA_RX_GOOD_PKT_CNT_OFFSET,
+					 STATS_USER_DATA_RX_GOOD_PKT_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_bad_user_pkt_show - Returns the total bad user rx packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total bad user rx packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_bad_user_pkt_show(struct kobject *kobj,
+					  struct kobj_attribute *attr,
+					  char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_DATA_RX_BAD_PKT_CNT_ADDR,
+					 STATS_USER_DATA_RX_BAD_PKT_CNT_OFFSET,
+					 STATS_USER_DATA_RX_BAD_PKT_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_bad_user_fcs_show - Returns the total bad user rx fcs count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total bad user frame check sequences count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_bad_user_fcs_show(struct kobject *kobj,
+					  struct kobj_attribute *attr,
+					  char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_DATA_RX_BAD_FCS_CNT_ADDR,
+					 STATS_USER_DATA_RX_BAD_FCS_CNT_OFFSET,
+					 STATS_USER_DATA_RX_BAD_FCS_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_user_ctrl_pkt_show - Returns the total user rx control packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total user rx control packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_user_ctrl_pkt_show(struct kobject *kobj,
+					   struct kobj_attribute *attr,
+					   char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_CTRL_RX_PACKETS_CNT_ADDR,
+					 STATS_USER_CTRL_RX_PACKETS_CNT_OFFSET,
+					 STATS_USER_CTRL_RX_PACKETS_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_good_user_ctrl_pkt_show - Returns the total good user rx
+ * control packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total good user rx control packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_good_user_ctrl_pkt_show(struct kobject *kobj,
+						struct kobj_attribute *attr,
+						char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_CTRL_RX_GOOD_PKT_CNT_ADDR,
+					 STATS_USER_CTRL_RX_GOOD_PKT_CNT_OFFSET,
+					 STATS_USER_CTRL_RX_GOOD_PKT_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_bad_user_ctrl_pkt_show - Returns the total bad user rx
+ * control packet count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total bad user rx control packet count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_bad_user_ctrl_pkt_show(struct kobject *kobj,
+					       struct kobj_attribute *attr,
+					       char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_CTRL_RX_BAD_PKT_CNT_ADDR,
+					 STATS_USER_CTRL_RX_BAD_PKT_CNT_OFFSET,
+					 STATS_USER_CTRL_RX_BAD_PKT_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * total_rx_bad_user_ctrl_fcs_show - Returns the total bad user rx
+ * control fcs count
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total bad user control frame check sequences count
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t total_rx_bad_user_ctrl_fcs_show(struct kobject *kobj,
+					       struct kobj_attribute *attr,
+					       char *buff)
+{
+	u32 count;
+
+	count = utils_sysfs_show_wrapper(STATS_USER_CTRL_RX_BAD_FCS_CNT_ADDR,
+					 STATS_USER_CTRL_RX_BAD_FCS_CNT_OFFSET,
+					 STATS_USER_CTRL_RX_BAD_FCS_CNT_MASK,
+					 kobj);
+	return sprintf(buff, "%d\n", count);
+}
+
+/**
+ * rx_user_pkt_rate_show - Returns the rate of user packets
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total user rx packet count
+ *
+ * Return: Returns the rate of user packets
+ */
+static ssize_t rx_user_pkt_rate_show(struct kobject *kobj,
+				     struct kobj_attribute *attr, char *buff)
+{
+	u32 rate;
+
+	rate = utils_sysfs_show_wrapper(STATS_USER_DATA_RX_PKTS_RATE_ADDR,
+					STATS_USER_DATA_RX_PKTS_RATE_OFFSET,
+					STATS_USER_DATA_RX_PKTS_RATE_MASK,
+					kobj);
+	return sprintf(buff, "%d\n", rate);
+}
+
+/**
+ * rx_user_ctrl_pkt_rate_show - Returns the rate of user control packets
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer the value will be written to
+ *
+ * Returns the total user rx packet count
+ *
+ * Return: Returns the rate of user control packets
+ */
+static ssize_t rx_user_ctrl_pkt_rate_show(struct kobject *kobj,
+					  struct kobj_attribute *attr,
+					  char *buff)
+{
+	u32 rate;
+
+	rate = utils_sysfs_show_wrapper(STATS_USER_CTRL_RX_PKTS_RATE_ADDR,
+					STATS_USER_CTRL_RX_PKTS_RATE_OFFSET,
+					STATS_USER_CTRL_RX_PKTS_RATE_MASK,
+					kobj);
+	return sprintf(buff, "%d\n", rate);
+}
+
+/* TODO Use DEVICE_ATTR/_RW/_RO macros */
+static struct kobj_attribute total_rx_good_pkt_attribute =
+	__ATTR(total_rx_good_pkt, 0444, total_rx_good_pkt_show, NULL);
+static struct kobj_attribute total_rx_bad_pkt_attribute =
+	__ATTR(total_rx_bad_pkt, 0444, total_rx_bad_pkt_show, NULL);
+static struct kobj_attribute total_rx_bad_fcs_attribute =
+	__ATTR(total_rx_bad_fcs, 0444, total_rx_bad_fcs_show, NULL);
+static struct kobj_attribute total_rx_user_pkt_attribute =
+	__ATTR(total_rx_user_pkt, 0444, total_rx_user_pkt_show, NULL);
+static struct kobj_attribute total_rx_good_user_pkt_attribute =
+	__ATTR(total_rx_good_user_pkt, 0444, total_rx_good_user_pkt_show, NULL);
+static struct kobj_attribute total_rx_bad_user_pkt_attribute =
+	__ATTR(total_rx_bad_user_pkt, 0444, total_rx_bad_user_pkt_show, NULL);
+static struct kobj_attribute total_rx_bad_user_fcs_attribute =
+	__ATTR(total_rx_bad_user_fcs, 0444, total_rx_bad_user_fcs_show, NULL);
+static struct kobj_attribute total_rx_user_ctrl_pkt_attribute =
+	__ATTR(total_rx_user_ctrl_pkt, 0444, total_rx_user_ctrl_pkt_show, NULL);
+static struct kobj_attribute total_rx_good_user_ctrl_pkt_attribute =
+	__ATTR(total_rx_good_user_ctrl_pkt, 0444,
+	       total_rx_good_user_ctrl_pkt_show, NULL);
+static struct kobj_attribute total_rx_bad_user_ctrl_pkt_attribute =
+	__ATTR(total_rx_bad_user_ctrl_pkt, 0444,
+	       total_rx_bad_user_ctrl_pkt_show, NULL);
+static struct kobj_attribute total_rx_bad_user_ctrl_fcs_attribute =
+	__ATTR(total_rx_bad_user_ctrl_fcs, 0444,
+	       total_rx_bad_user_ctrl_fcs_show, NULL);
+static struct kobj_attribute rx_user_pkt_rate_attribute =
+	__ATTR(rx_user_pkt_rate, 0444, rx_user_pkt_rate_show, NULL);
+static struct kobj_attribute rx_user_ctrl_pkt_rate_attribute =
+	__ATTR(rx_user_ctrl_pkt_rate, 0444, rx_user_ctrl_pkt_rate_show, NULL);
+
+static struct attribute *attrs[] = {
+	&total_rx_good_pkt_attribute.attr,
+	&total_rx_bad_pkt_attribute.attr,
+	&total_rx_bad_fcs_attribute.attr,
+	&total_rx_user_pkt_attribute.attr,
+	&total_rx_good_user_pkt_attribute.attr,
+	&total_rx_bad_user_pkt_attribute.attr,
+	&total_rx_bad_user_fcs_attribute.attr,
+	&total_rx_user_ctrl_pkt_attribute.attr,
+	&total_rx_good_user_ctrl_pkt_attribute.attr,
+	&total_rx_bad_user_ctrl_pkt_attribute.attr,
+	&total_rx_bad_user_ctrl_fcs_attribute.attr,
+	&rx_user_pkt_rate_attribute.attr,
+	&rx_user_ctrl_pkt_rate_attribute.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+
+struct kobject *kobj_stats;
+
+/**
+ * xroe_sysfs_stats_init - Creates the xroe sysfs "stats" subdirectory & entries
+ *
+ * Return: 0 on success, negative value in case of failure to
+ * create the sysfs group
+ *
+ * Creates the xroe sysfs "stats" subdirectory and entries under "xroe"
+ */
+int xroe_sysfs_stats_init(void)
+{
+	int ret;
+
+	kobj_stats = kobject_create_and_add("stats", root_xroe_kobj);
+	if (!kobj_stats)
+		return -ENOMEM;
+
+	ret = sysfs_create_group(kobj_stats, &attr_group);
+	if (ret)
+		kobject_put(kobj_stats);
+
+	return ret;
+}
+
+/**
+ * xroe_sysfs_stats_exit - Deletes the xroe sysfs "ipv4" subdirectory & entries
+ *
+ * Deletes the xroe sysfs "stats" subdirectory and entries,
+ * under the "xroe" entry
+ */
+void xroe_sysfs_stats_exit(void)
+{
+	kobject_put(kobj_stats);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/sysfs_xroe_framer_udp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/sysfs_xroe_framer_udp.c
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "xroe_framer.h"
+
+enum { XROE_SIZE_MAX = 15 };
+static int xroe_size;
+
+/**
+ * udp_source_port_show - Returns the UDP source port
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the UDP source port
+ *
+ * Returns the UDP source port
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t udp_source_port_show(struct kobject *kobj,
+				    struct kobj_attribute *attr,
+				    char *buff)
+{
+	u32 source_port;
+
+	source_port = utils_sysfs_show_wrapper(ETH_UDP_SOURCE_PORT_ADDR,
+					       ETH_UDP_SOURCE_PORT_OFFSET,
+					       ETH_UDP_SOURCE_PORT_MASK, kobj);
+	sprintf(buff, "%d\n", source_port);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * udp_source_port_store - Writes to the UDP source port sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the UDP source port
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the UDP source port sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t udp_source_port_store(struct kobject *kobj,
+				     struct kobj_attribute *attr,
+				     const char *buff, size_t count)
+{
+	int ret;
+	u32 source_port;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &source_port);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_UDP_SOURCE_PORT_ADDR,
+				  ETH_UDP_SOURCE_PORT_OFFSET,
+				  ETH_UDP_SOURCE_PORT_MASK, source_port, kobj);
+	return xroe_size;
+}
+
+/**
+ * udp_destination_port_show - Returns the UDP destination port
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the UDP destination port
+ *
+ * Returns the UDP destination port
+ *
+ * Return: XROE_SIZE_MAX on success
+ */
+static ssize_t udp_destination_port_show(struct kobject *kobj,
+					 struct kobj_attribute *attr,
+					 char *buff)
+{
+	u32 dest_port;
+
+	dest_port = utils_sysfs_show_wrapper(ETH_UDP_DESTINATION_PORT_ADDR,
+					     ETH_UDP_DESTINATION_PORT_OFFSET,
+					     ETH_UDP_DESTINATION_PORT_MASK,
+					     kobj);
+	sprintf(buff, "%d\n", dest_port);
+	return XROE_SIZE_MAX;
+}
+
+/**
+ * udp_destination_port_store - Writes to the UDP destination port sysfs entry
+ * @kobj:	The kernel object of the entry
+ * @attr:	The attributes of the kernel object
+ * @buff:	The buffer containing the UDP destination port
+ * @count:	The number of characters typed by the user
+ *
+ * Writes to the UDP destination port sysfs entry
+ *
+ * Return: XROE_SIZE_MAX or the value of "count", if that's lesser, on success
+ */
+static ssize_t udp_destination_port_store(struct kobject *kobj,
+					  struct kobj_attribute *attr,
+					  const char *buff, size_t count)
+{
+	int ret;
+	u32 dest_port;
+
+	xroe_size = min_t(size_t, count, (size_t)XROE_SIZE_MAX);
+	ret = kstrtouint(buff, 10, &dest_port);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(ETH_UDP_DESTINATION_PORT_ADDR,
+				  ETH_UDP_DESTINATION_PORT_OFFSET,
+				  ETH_UDP_DESTINATION_PORT_MASK, dest_port,
+				  kobj);
+	return xroe_size;
+}
+
+/* TODO Use DEVICE_ATTR/_RW/_RO macros */
+
+static struct kobj_attribute source_port =
+	__ATTR(source_port, 0660, udp_source_port_show,
+	       udp_source_port_store);
+static struct kobj_attribute dest_port =
+	__ATTR(dest_port, 0660, udp_destination_port_show,
+	       udp_destination_port_store);
+
+static struct attribute *attrs[] = {
+	&source_port.attr,
+	&dest_port.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+
+static struct kobject *kobj_udp[MAX_NUM_ETH_PORTS];
+
+/**
+ * xroe_sysfs_udp_init - Creates the xroe sysfs "udp" subdirectory and entries
+ *
+ * Return: 0 on success, negative value in case of failure to
+ * create the sysfs group
+ *
+ * Creates the xroe sysfs "udp" subdirectory and entries under "xroe"
+ */
+int xroe_sysfs_udp_init(void)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		kobj_udp[i] = kobject_create_and_add("udp",  kobj_eth_ports[i]);
+		if (!kobj_udp[i])
+			return -ENOMEM;
+		ret = sysfs_create_group(kobj_udp[i], &attr_group);
+		if (ret)
+			kobject_put(kobj_udp[i]);
+	}
+	return ret;
+}
+
+/**
+ * xroe_sysfs_ipv6_exit - Deletes the xroe sysfs "udp" subdirectory & entries
+ *
+ * Deletes the xroe sysfs "udp" subdirectory and entries,
+ * under the "xroe" entry
+ *
+ */
+void xroe_sysfs_udp_exit(void)
+{
+	int i;
+
+	for (i = 0; i < MAX_NUM_ETH_PORTS; i++)
+		kobject_put(kobj_udp[i]);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/xroe_framer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/xroe_framer.c
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include "xroe_framer.h"
+
+#define DRIVER_NAME "framer"
+
+/*
+ * TODO: to be made static as well, so that multiple instances can be used. As
+ * of now, the "xroe_lp" structure is shared among the multiple source files
+ */
+struct framer_local *xroe_lp;
+static struct platform_driver framer_driver;
+/*
+ * TODO: placeholder for the IRQ once it's been implemented
+ * in the framer block
+ */
+static irqreturn_t framer_irq(int irq, void *xroe_lp)
+{
+	return IRQ_HANDLED;
+}
+
+/**
+ * framer_probe - Probes the device tree to locate the framer block
+ * @pdev:	The structure containing the device's details
+ *
+ * Probes the device tree to locate the framer block and maps it to
+ * the kernel virtual memory space
+ *
+ * Return: 0 on success or a negative errno on error.
+ */
+static int framer_probe(struct platform_device *pdev)
+{
+	struct resource *r_mem; /* IO mem resources */
+	struct resource *r_irq;
+	struct device *dev = &pdev->dev;
+	int rc = 0;
+
+	dev_dbg(dev, "Device Tree Probing\n");
+	xroe_lp = devm_kzalloc(&pdev->dev, sizeof(*xroe_lp), GFP_KERNEL);
+	if (!xroe_lp)
+		return -ENOMEM;
+
+	/* Get iospace for the device */
+	r_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xroe_lp->base_addr = devm_ioremap_resource(&pdev->dev, r_mem);
+	if (IS_ERR(xroe_lp->base_addr))
+		return PTR_ERR(xroe_lp->base_addr);
+
+	dev_set_drvdata(dev, xroe_lp);
+	xroe_sysfs_init();
+	/* Get IRQ for the device */
+	/*
+	 * TODO: No IRQ *yet* in the DT from the framer block, as it's still
+	 * under development. To be added once it's in the block, and also
+	 * replace with platform_get_irq_byname()
+	 */
+	r_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (IS_ERR(r_irq)) {
+		dev_info(dev, "no IRQ found\n");
+		/*
+		 * TODO: Return non-zero (error) code on no IRQ found.
+		 * To be implemented once the IRQ is in the block
+		 */
+		return 0;
+	}
+	rc = devm_request_irq(dev, xroe_lp->irq, &framer_irq, 0, DRIVER_NAME, xroe_lp);
+	if (rc) {
+		dev_err(dev, "testmodule: Could not allocate interrupt %d.\n",
+			xroe_lp->irq);
+		/*
+		 * TODO: Return non-zero (error) code on no IRQ found.
+		 * To be implemented once the IRQ is in the block
+		 */
+		return 0;
+	}
+
+	return rc;
+}
+
+/**
+ * framer_init - Registers the driver
+ *
+ * Return: 0 on success, -1 on allocation error
+ *
+ * Registers the framer driver and creates character device drivers
+ * for the whole block, as well as separate ones for stats and
+ * radio control.
+ */
+static int __init framer_init(void)
+{
+	int ret;
+
+	pr_debug("XROE framer driver init\n");
+
+	ret = platform_driver_register(&framer_driver);
+
+	return ret;
+}
+
+/**
+ * framer_exit - Destroys the driver
+ *
+ * Unregisters the framer driver and destroys the character
+ * device driver for the whole block, as well as the separate ones
+ * for stats and radio control. Returns 0 upon successful execution
+ */
+static void __exit framer_exit(void)
+{
+	xroe_sysfs_exit();
+	platform_driver_unregister(&framer_driver);
+	pr_info("XROE Framer exit\n");
+}
+
+module_init(framer_init);
+module_exit(framer_exit);
+
+static const struct of_device_id framer_of_match[] = {
+	{ .compatible = "xlnx,roe-framer-1.0", },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, framer_of_match);
+
+static struct platform_driver framer_driver = {
+	.driver = {
+		/*
+		 * TODO: .name shouldn't be necessary, though removing
+		 * it results in kernel panic. To investigate further
+		 */
+		.name = DRIVER_NAME,
+		.of_match_table = framer_of_match,
+	},
+	.probe = framer_probe,
+};
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("framer - Xilinx Radio over Ethernet Framer driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroeframer/xroe_framer.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroeframer/xroe_framer.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+#include "roe_framer_ctrl.h"
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioctl.h>
+#include <linux/kernel.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include <linux/uaccess.h>
+#include <uapi/linux/stat.h> /* S_IRUSR, S_IWUSR */
+
+/* TODO: Remove hardcoded value of number of Ethernet ports and read the value
+ * from the device tree.
+ */
+#define MAX_NUM_ETH_PORTS 0x4
+/* TODO: to be made static as well, so that multiple instances can be used. As
+ * of now, the following 3 structures are shared among the multiple
+ * source files
+ */
+extern struct framer_local *xroe_lp;
+extern struct kobject *root_xroe_kobj;
+extern struct kobject *kobj_framer;
+extern struct kobject *kobj_eth_ports[MAX_NUM_ETH_PORTS];
+struct framer_local {
+	int irq;
+	unsigned long mem_start;
+	unsigned long mem_end;
+	void __iomem *base_addr;
+};
+
+int xroe_sysfs_init(void);
+int xroe_sysfs_ipv4_init(void);
+int xroe_sysfs_ipv6_init(void);
+int xroe_sysfs_udp_init(void);
+int xroe_sysfs_stats_init(void);
+void xroe_sysfs_exit(void);
+void xroe_sysfs_ipv4_exit(void);
+void xroe_sysfs_ipv6_exit(void);
+void xroe_sysfs_udp_exit(void);
+void xroe_sysfs_stats_exit(void);
+int utils_write32withmask(void __iomem *working_address, u32 value,
+			  u32 mask, u32 offset);
+int utils_check_address_offset(u32 offset, size_t device_size);
+void utils_sysfs_store_wrapper(u32 address, u32 offset, u32 mask, u32 value,
+			       struct kobject *kobj);
+u32 utils_sysfs_show_wrapper(u32 address, u32 offset, u32 mask,
+			     struct kobject *kobj);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/Kconfig
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+
+#
+# Xilinx Radio over Ethernet Traffic Generator driver
+#
+
+config XROE_TRAFFIC_GEN
+	tristate "Xilinx Radio over Ethernet Traffic Generator driver"
+	help
+	  The Traffic Generator is used for in testing of other RoE IP Blocks
+	  (currenty the XRoE Framer) and simulates an radio antenna interface.
+	  It generates rolling rampdata for eCPRI antenna paths.
+	  Each path is tagged with the antenna number. The sink locks to this
+	  ramp data, then checks the next value is as expected.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for Radio over Ethernet Framer driver
+#
+obj-$(XROE_TRAFFIC_GEN)	:= xroe_traffic_gen.o
+
+framer-objs := 	xroe-traffic-gen.o \
+		xroe-traffic-gen-sysfs.o \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/README
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/README
@@ -0,0 +1,19 @@
+Xilinx Radio over Ethernet Traffic Generator driver
+===================================================
+
+About the RoE Framer Traffic Generator
+
+The Traffic Generator is used for in testing of other RoE IP Blocks (currenty
+the XRoE Framer) and simulates an radio antenna interface. It generates rolling
+rampdata for eCPRI antenna paths. Each path is tagged with the antenna number.
+The sink locks to this ramp data, then checks the next value is as expected.
+
+
+About the Linux Driver
+
+The RoE Traffic Generator Linux Driver provides sysfs access to control a
+simulated radio antenna interface.
+The loading of the driver to the hardware is possible using Device Tree binding
+(see "dt-binding.txt" for more information). When the driver is loaded, the
+general controls (such as sink lock, enable, loopback etc) are exposed
+under /sys/kernel/xroetrafficgen.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/dt-binding.txt
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/dt-binding.txt
@@ -0,0 +1,15 @@
+* Xilinx Radio over Ethernet Traffic Generator driver
+
+Required properties:
+- compatible: must be "xlnx,roe-framer-1.0"
+- reg: physical base address of the framer and length of memory mapped region
+- clock-names: list of clock names
+- clocks: list of clock sources corresponding to the clock names
+
+Example:
+	roe_radio_ctrl@a0060000 {
+		compatible = "xlnx,roe-traffic-gen-1.0";
+		reg = <0x0 0xa0060000 0x0 0x10000>;
+		clock-names = "s_axis_fram_aclk", "s_axi_aclk";
+		clocks = <0x44 0x43>;
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/roe_radio_ctrl.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/roe_radio_ctrl.h
@@ -0,0 +1,183 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+/*-----------------------------------------------------------------------------
+ * C Header bank BASE definitions
+ *-----------------------------------------------------------------------------
+ */
+#define ROE_RADIO_CFG_BASE_ADDR 0x0
+#define ROE_RADIO_SOURCE_BASE_ADDR 0x1000
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_radio_cfg
+ * with prefix radio_ @ address 0x0
+ *-----------------------------------------------------------------------------
+ */
+/* Type = roInt */
+#define RADIO_ID_ADDR 0x0
+#define RADIO_ID_MASK 0xffffffff
+#define RADIO_ID_OFFSET 0x0
+#define RADIO_ID_WIDTH 0x20
+#define RADIO_ID_DEFAULT 0x120001
+
+/* Type = rw */
+#define RADIO_TIMEOUT_ENABLE_ADDR 0x4
+#define RADIO_TIMEOUT_ENABLE_MASK 0x1
+#define RADIO_TIMEOUT_ENABLE_OFFSET 0x0
+#define RADIO_TIMEOUT_ENABLE_WIDTH 0x1
+#define RADIO_TIMEOUT_ENABLE_DEFAULT 0x0
+
+/* Type = ro */
+#define RADIO_TIMEOUT_STATUS_ADDR 0x8
+#define RADIO_TIMEOUT_STATUS_MASK 0x1
+#define RADIO_TIMEOUT_STATUS_OFFSET 0x0
+#define RADIO_TIMEOUT_STATUS_WIDTH 0x1
+#define RADIO_TIMEOUT_STATUS_DEFAULT 0x1
+
+/* Type = rw */
+#define RADIO_TIMEOUT_VALUE_ADDR 0xc
+#define RADIO_TIMEOUT_VALUE_MASK 0xfff
+#define RADIO_TIMEOUT_VALUE_OFFSET 0x0
+#define RADIO_TIMEOUT_VALUE_WIDTH 0xc
+#define RADIO_TIMEOUT_VALUE_DEFAULT 0x80
+
+/* Type = rw */
+#define RADIO_GPIO_CDC_LEDMODE2_ADDR 0x10
+#define RADIO_GPIO_CDC_LEDMODE2_MASK 0x1
+#define RADIO_GPIO_CDC_LEDMODE2_OFFSET 0x0
+#define RADIO_GPIO_CDC_LEDMODE2_WIDTH 0x1
+#define RADIO_GPIO_CDC_LEDMODE2_DEFAULT 0x0
+
+/* Type = rw */
+#define RADIO_GPIO_CDC_LEDGPIO_ADDR 0x10
+#define RADIO_GPIO_CDC_LEDGPIO_MASK 0x30
+#define RADIO_GPIO_CDC_LEDGPIO_OFFSET 0x4
+#define RADIO_GPIO_CDC_LEDGPIO_WIDTH 0x2
+#define RADIO_GPIO_CDC_LEDGPIO_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_GPIO_CDC_DIPSTATUS_ADDR 0x14
+#define RADIO_GPIO_CDC_DIPSTATUS_MASK 0xff
+#define RADIO_GPIO_CDC_DIPSTATUS_OFFSET 0x0
+#define RADIO_GPIO_CDC_DIPSTATUS_WIDTH 0x8
+#define RADIO_GPIO_CDC_DIPSTATUS_DEFAULT 0x0
+
+/* Type = wPlsH */
+#define RADIO_SW_TRIGGER_ADDR 0x20
+#define RADIO_SW_TRIGGER_MASK 0x1
+#define RADIO_SW_TRIGGER_OFFSET 0x0
+#define RADIO_SW_TRIGGER_WIDTH 0x1
+#define RADIO_SW_TRIGGER_DEFAULT 0x0
+
+/* Type = rw */
+#define RADIO_CDC_ENABLE_ADDR 0x24
+#define RADIO_CDC_ENABLE_MASK 0x1
+#define RADIO_CDC_ENABLE_OFFSET 0x0
+#define RADIO_CDC_ENABLE_WIDTH 0x1
+#define RADIO_CDC_ENABLE_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_ERROR_ADDR 0x24
+#define RADIO_CDC_ERROR_MASK 0x2
+#define RADIO_CDC_ERROR_OFFSET 0x1
+#define RADIO_CDC_ERROR_WIDTH 0x1
+#define RADIO_CDC_ERROR_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_STATUS_ADDR 0x24
+#define RADIO_CDC_STATUS_MASK 0x4
+#define RADIO_CDC_STATUS_OFFSET 0x2
+#define RADIO_CDC_STATUS_WIDTH 0x1
+#define RADIO_CDC_STATUS_DEFAULT 0x0
+
+/* Type = rw */
+#define RADIO_CDC_LOOPBACK_ADDR 0x28
+#define RADIO_CDC_LOOPBACK_MASK 0x1
+#define RADIO_CDC_LOOPBACK_OFFSET 0x0
+#define RADIO_CDC_LOOPBACK_WIDTH 0x1
+#define RADIO_CDC_LOOPBACK_DEFAULT 0x0
+
+/* Type = rw */
+#define RADIO_SINK_ENABLE_ADDR 0x2c
+#define RADIO_SINK_ENABLE_MASK 0x1
+#define RADIO_SINK_ENABLE_OFFSET 0x0
+#define RADIO_SINK_ENABLE_WIDTH 0x1
+#define RADIO_SINK_ENABLE_DEFAULT 0x1
+
+/* Type = roSig */
+#define RADIO_CDC_ERROR_31_0_ADDR 0x30
+#define RADIO_CDC_ERROR_31_0_MASK 0xffffffff
+#define RADIO_CDC_ERROR_31_0_OFFSET 0x0
+#define RADIO_CDC_ERROR_31_0_WIDTH 0x20
+#define RADIO_CDC_ERROR_31_0_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_ERROR_63_32_ADDR 0x34
+#define RADIO_CDC_ERROR_63_32_MASK 0xffffffff
+#define RADIO_CDC_ERROR_63_32_OFFSET 0x0
+#define RADIO_CDC_ERROR_63_32_WIDTH 0x20
+#define RADIO_CDC_ERROR_63_32_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_ERROR_95_64_ADDR 0x38
+#define RADIO_CDC_ERROR_95_64_MASK 0xffffffff
+#define RADIO_CDC_ERROR_95_64_OFFSET 0x0
+#define RADIO_CDC_ERROR_95_64_WIDTH 0x20
+#define RADIO_CDC_ERROR_95_64_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_ERROR_127_96_ADDR 0x3c
+#define RADIO_CDC_ERROR_127_96_MASK 0xffffffff
+#define RADIO_CDC_ERROR_127_96_OFFSET 0x0
+#define RADIO_CDC_ERROR_127_96_WIDTH 0x20
+#define RADIO_CDC_ERROR_127_96_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_STATUS_31_0_ADDR 0x40
+#define RADIO_CDC_STATUS_31_0_MASK 0xffffffff
+#define RADIO_CDC_STATUS_31_0_OFFSET 0x0
+#define RADIO_CDC_STATUS_31_0_WIDTH 0x20
+#define RADIO_CDC_STATUS_31_0_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_STATUS_63_32_ADDR 0x44
+#define RADIO_CDC_STATUS_63_32_MASK 0xffffffff
+#define RADIO_CDC_STATUS_63_32_OFFSET 0x0
+#define RADIO_CDC_STATUS_63_32_WIDTH 0x20
+#define RADIO_CDC_STATUS_63_32_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_STATUS_95_64_ADDR 0x48
+#define RADIO_CDC_STATUS_95_64_MASK 0xffffffff
+#define RADIO_CDC_STATUS_95_64_OFFSET 0x0
+#define RADIO_CDC_STATUS_95_64_WIDTH 0x20
+#define RADIO_CDC_STATUS_95_64_DEFAULT 0x0
+
+/* Type = roSig */
+#define RADIO_CDC_STATUS_127_96_ADDR 0x4c
+#define RADIO_CDC_STATUS_127_96_MASK 0xffffffff
+#define RADIO_CDC_STATUS_127_96_OFFSET 0x0
+#define RADIO_CDC_STATUS_127_96_WIDTH 0x20
+#define RADIO_CDC_STATUS_127_96_DEFAULT 0x0
+
+/*-----------------------------------------------------------------------------
+ * C Header bank register definitions for bank roe_radio_source
+ * with prefix fram_ @ address 0x1000
+ *-----------------------------------------------------------------------------
+ */
+/* Type = rwpdef */
+#define FRAM_PACKET_DATA_SIZE_ADDR 0x1000
+#define FRAM_PACKET_DATA_SIZE_MASK 0x7f
+#define FRAM_PACKET_DATA_SIZE_OFFSET 0x0
+#define FRAM_PACKET_DATA_SIZE_WIDTH 0x7
+#define FRAM_PACKET_DATA_SIZE_DEFAULT 0x0
+
+/* Type = rwpdef */
+#define FRAM_PAUSE_DATA_SIZE_ADDR 0x1004
+#define FRAM_PAUSE_DATA_SIZE_MASK 0x7f
+#define FRAM_PAUSE_DATA_SIZE_OFFSET 0x0
+#define FRAM_PAUSE_DATA_SIZE_WIDTH 0x7
+#define FRAM_PAUSE_DATA_SIZE_DEFAULT 0x0
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/xroe-traffic-gen-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/xroe-traffic-gen-sysfs.c
@@ -0,0 +1,824 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "roe_radio_ctrl.h"
+#include "xroe-traffic-gen.h"
+
+static int xroe_size;
+static char xroe_tmp[XROE_SIZE_MAX];
+
+/**
+ * utils_sysfs_store_wrapper - Wraps the storing function for sysfs entries
+ * @dev:	The structure containing the device's information
+ * @address:	The address of the register to be written
+ * @offset:	The offset from the address of the register
+ * @mask:	The mask to be used on the value to be written
+ * @value:	The value to be written to the register
+ *
+ * Wraps the core functionality of all "store" functions of sysfs entries.
+ */
+static void utils_sysfs_store_wrapper(struct device *dev, u32 address,
+				      u32 offset, u32 mask, u32 value)
+{
+	void __iomem *working_address;
+	u32 read_register_value = 0;
+	u32 register_value_to_write = 0;
+	u32 delta = 0;
+	u32 buffer = 0;
+	struct xroe_traffic_gen_local *lp = dev_get_drvdata(dev);
+
+	working_address = (void __iomem *)(lp->base_addr + address);
+	read_register_value = ioread32(working_address);
+	buffer = (value << offset);
+	register_value_to_write = read_register_value & ~mask;
+	delta = buffer & mask;
+	register_value_to_write |= delta;
+	iowrite32(register_value_to_write, working_address);
+}
+
+/**
+ * utils_sysfs_show_wrapper - Wraps the "show" function for sysfs entries
+ * @dev:	The structure containing the device's information
+ * @address:	The address of the register to be read
+ * @offset:	The offset from the address of the register
+ * @mask:	The mask to be used on the value to be read
+ *
+ * Wraps the core functionality of all "show" functions of sysfs entries.
+ *
+ * Return: The value designated by the address, offset and mask
+ */
+static u32 utils_sysfs_show_wrapper(struct device *dev, u32 address, u32 offset,
+				    u32 mask)
+{
+	void __iomem *working_address;
+	u32 buffer;
+	struct xroe_traffic_gen_local *lp = dev_get_drvdata(dev);
+
+	working_address = (void __iomem *)(lp->base_addr + address);
+	buffer = ioread32(working_address);
+	return (buffer & mask) >> offset;
+}
+
+/**
+ * radio_id_show - Returns the block's ID number
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the ID number string
+ *
+ * Returns the traffic gen's ID (0x1179649 by default)
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t radio_id_show(struct device *dev,
+			     struct device_attribute *attr, char *buf)
+{
+	u32 radio_id;
+
+	radio_id = utils_sysfs_show_wrapper(dev, RADIO_ID_ADDR,
+					    RADIO_ID_OFFSET,
+					    RADIO_ID_MASK);
+	return sprintf(buf, "%d\n", radio_id);
+}
+static DEVICE_ATTR_RO(radio_id);
+
+/**
+ * timeout_enable_show - Returns the traffic gen's timeout enable status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the traffic gen's timeout enable status to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t timeout_enable_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	u32 timeout_enable;
+
+	timeout_enable = utils_sysfs_show_wrapper(dev,
+						  RADIO_TIMEOUT_ENABLE_ADDR,
+						  RADIO_TIMEOUT_ENABLE_OFFSET,
+						  RADIO_TIMEOUT_ENABLE_MASK);
+	return sprintf(buf, "%d\n", timeout_enable);
+}
+
+/**
+ * timeout_enable_store - Writes to the traffic gens's timeout enable
+ * status register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's timeout enable
+ * status to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t timeout_enable_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	u32 enable = 0;
+
+	strncpy(xroe_tmp, buf, xroe_size);
+	if (strncmp(xroe_tmp, "true", xroe_size) == 0)
+		enable = 1;
+	else if (strncmp(xroe_tmp, "false", xroe_size) == 0)
+		enable = 0;
+	utils_sysfs_store_wrapper(dev, RADIO_TIMEOUT_ENABLE_ADDR,
+				  RADIO_TIMEOUT_ENABLE_OFFSET,
+				  RADIO_TIMEOUT_ENABLE_MASK, enable);
+	return count;
+}
+static DEVICE_ATTR_RW(timeout_enable);
+
+/**
+ * timeout_status_show - Returns the timeout status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the ID number string
+ *
+ * Returns the traffic gen's timeout status (0x1 by default)
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t timeout_status_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	u32 timeout;
+
+	timeout = utils_sysfs_show_wrapper(dev, RADIO_TIMEOUT_STATUS_ADDR,
+					   RADIO_TIMEOUT_STATUS_OFFSET,
+					   RADIO_TIMEOUT_STATUS_MASK);
+	return sprintf(buf, "%d\n", timeout);
+}
+static DEVICE_ATTR_RO(timeout_status);
+
+/**
+ * timeout_enable_show - Returns the traffic gen's timeout value
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the traffic gen's timeout value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t timeout_value_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	u32 timeout_value;
+
+	timeout_value = utils_sysfs_show_wrapper(dev, RADIO_TIMEOUT_VALUE_ADDR,
+						 RADIO_TIMEOUT_VALUE_OFFSET,
+						 RADIO_TIMEOUT_VALUE_MASK);
+	return sprintf(buf, "%d\n", timeout_value);
+}
+
+/**
+ * timeout_enable_store - Writes to the traffic gens's timeout value
+ * status register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's timeout value
+ * to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t timeout_value_store(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t count)
+{
+	u32 timeout_value;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &timeout_value);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_TIMEOUT_VALUE_ADDR,
+				  RADIO_TIMEOUT_VALUE_OFFSET,
+				  RADIO_TIMEOUT_VALUE_MASK, timeout_value);
+	return count;
+}
+static DEVICE_ATTR_RW(timeout_value);
+
+/**
+ * ledmode_show - Returns the current LED mode
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the traffic gen's LED mode value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t ledmode_show(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	u32 ledmode;
+
+	ledmode = utils_sysfs_show_wrapper(dev, RADIO_GPIO_CDC_LEDMODE2_ADDR,
+					   RADIO_GPIO_CDC_LEDMODE2_OFFSET,
+					   RADIO_GPIO_CDC_LEDMODE2_MASK);
+	return sprintf(buf, "%d\n", ledmode);
+}
+
+/**
+ * ledmode_store - Writes to the current LED mode register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's LED mode value
+ * to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t ledmode_store(struct device *dev,
+			     struct device_attribute *attr,
+			     const char *buf, size_t count)
+{
+	u32 ledmode;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &ledmode);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_GPIO_CDC_LEDMODE2_ADDR,
+				  RADIO_GPIO_CDC_LEDMODE2_OFFSET,
+				  RADIO_GPIO_CDC_LEDMODE2_MASK, ledmode);
+	return count;
+}
+static DEVICE_ATTR_RW(ledmode);
+
+/**
+ * ledgpio_show - Returns the current LED gpio
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the traffic gen's LED gpio value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t ledgpio_show(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	u32 ledgpio;
+
+	ledgpio = utils_sysfs_show_wrapper(dev, RADIO_GPIO_CDC_LEDGPIO_ADDR,
+					   RADIO_GPIO_CDC_LEDGPIO_OFFSET,
+					   RADIO_GPIO_CDC_LEDGPIO_MASK);
+	return sprintf(buf, "%d\n", ledgpio);
+}
+
+/**
+ * ledgpio_store - Writes to the current LED gpio register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's LED gpio value
+ * to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t ledgpio_store(struct device *dev,
+			     struct device_attribute *attr,
+			     const char *buf, size_t count)
+{
+	u32 ledgpio;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &ledgpio);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_GPIO_CDC_LEDGPIO_ADDR,
+				  RADIO_GPIO_CDC_LEDGPIO_OFFSET,
+				  RADIO_GPIO_CDC_LEDGPIO_MASK, ledgpio);
+	return count;
+}
+static DEVICE_ATTR_RW(ledgpio);
+
+/**
+ * dip_status_show - Returns the current DIP switch value
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the GPIO DIP switch value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t dip_status_show(struct device *dev,
+			       struct device_attribute *attr, char *buf)
+{
+	u32 dip_status;
+
+	dip_status = utils_sysfs_show_wrapper(dev, RADIO_GPIO_CDC_LEDGPIO_ADDR,
+					      RADIO_GPIO_CDC_LEDGPIO_OFFSET,
+					      RADIO_GPIO_CDC_LEDGPIO_MASK);
+	return sprintf(buf, "0x%08x\n", dip_status);
+}
+static DEVICE_ATTR_RO(dip_status);
+
+/**
+ * sw_trigger_show - Returns the current SW trigger status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the traffic gen's SW trigger status value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t sw_trigger_show(struct device *dev,
+			       struct device_attribute *attr,
+			       char *buf)
+{
+	u32 sw_trigger;
+
+	sw_trigger = utils_sysfs_show_wrapper(dev, RADIO_SW_TRIGGER_ADDR,
+					      RADIO_SW_TRIGGER_OFFSET,
+					      RADIO_SW_TRIGGER_MASK);
+	return sprintf(buf, "%d\n", sw_trigger);
+}
+
+/**
+ * sw_trigger_store - Writes to the SW trigger status register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's SW trigger
+ * value to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t sw_trigger_store(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	u32 sw_trigger;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &sw_trigger);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_SW_TRIGGER_ADDR,
+				  RADIO_SW_TRIGGER_OFFSET,
+				  RADIO_SW_TRIGGER_MASK, sw_trigger);
+	return count;
+}
+static DEVICE_ATTR_RW(sw_trigger);
+
+/**
+ * radio_enable_show - Returns the current radio enable status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the enable status
+ *
+ * Reads and writes the traffic gen's radio enable value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t radio_enable_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	u32 radio_enable;
+
+	radio_enable = utils_sysfs_show_wrapper(dev, RADIO_CDC_ENABLE_ADDR,
+						RADIO_CDC_ENABLE_OFFSET,
+						RADIO_CDC_ENABLE_MASK);
+	return sprintf(buf, "%d\n", radio_enable);
+}
+
+/**
+ * radio_enable_store - Writes to the radio enable register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's radio enable
+ * value to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t radio_enable_store(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t count)
+{
+	u32 radio_enable;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &radio_enable);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_CDC_ENABLE_ADDR,
+				  RADIO_CDC_ENABLE_OFFSET,
+				  RADIO_CDC_ENABLE_MASK,
+				  radio_enable);
+	return count;
+}
+static DEVICE_ATTR_RW(radio_enable);
+
+/**
+ * radio_error_show - Returns the current radio error status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the error status
+ *
+ * Reads and writes the traffic gen's radio error value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t radio_error_show(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	u32 radio_error;
+
+	radio_error = utils_sysfs_show_wrapper(dev, RADIO_CDC_ERROR_ADDR,
+					       RADIO_CDC_STATUS_OFFSET,
+					       RADIO_CDC_STATUS_MASK);
+	return sprintf(buf, "%d\n", radio_error);
+}
+static DEVICE_ATTR_RO(radio_error);
+
+/**
+ * radio_status_show - Returns the current radio status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the status
+ *
+ * Reads and writes the traffic gen's radio status value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t radio_status_show(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	u32 radio_status;
+
+	radio_status = utils_sysfs_show_wrapper(dev, RADIO_CDC_STATUS_ADDR,
+						RADIO_CDC_STATUS_OFFSET,
+						RADIO_CDC_STATUS_MASK);
+	return sprintf(buf, "%d\n", radio_status);
+}
+static DEVICE_ATTR_RO(radio_status);
+
+/**
+ * radio_loopback_show - Returns the current radio loopback status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the loopback status
+ *
+ * Reads and writes the traffic gen's radio loopback value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t radio_loopback_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	u32 radio_loopback;
+
+	radio_loopback = utils_sysfs_show_wrapper(dev,
+						  RADIO_CDC_LOOPBACK_ADDR,
+						  RADIO_CDC_LOOPBACK_OFFSET,
+						  RADIO_CDC_LOOPBACK_MASK);
+	return sprintf(buf, "%d\n", radio_loopback);
+}
+
+/**
+ * radio_loopback_store - Writes to the radio loopback register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's radio loopback
+ * value to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t radio_loopback_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	u32 radio_loopback;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &radio_loopback);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_CDC_LOOPBACK_ADDR,
+				  RADIO_CDC_LOOPBACK_OFFSET,
+				  RADIO_CDC_LOOPBACK_MASK, radio_loopback);
+	return count;
+}
+static DEVICE_ATTR_RW(radio_loopback);
+
+/**
+ * radio_sink_enable_show - Returns the current radio sink enable status
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the loopback status
+ *
+ * Reads and writes the traffic gen's radio sink enable value to the sysfs entry
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t radio_sink_enable_show(struct device *dev,
+				      struct device_attribute *attr, char *buf)
+{
+	u32 sink_enable;
+
+	sink_enable = utils_sysfs_show_wrapper(dev, RADIO_SINK_ENABLE_ADDR,
+					       RADIO_SINK_ENABLE_OFFSET,
+					       RADIO_SINK_ENABLE_MASK);
+	return sprintf(buf, "%d\n", sink_enable);
+}
+
+/**
+ * radio_sink_enable_store - Writes to the radio sink enable register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's radio sink
+ * enable value to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t radio_sink_enable_store(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t count)
+{
+	u32 sink_enable;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &sink_enable);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, RADIO_SINK_ENABLE_ADDR,
+				  RADIO_SINK_ENABLE_OFFSET,
+				  RADIO_SINK_ENABLE_MASK, sink_enable);
+	return count;
+}
+static DEVICE_ATTR_RW(radio_sink_enable);
+
+/**
+ * antenna_status_show - Returns the status for all antennas
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the ID number string
+ *
+ * Returns the traffic gen's status for all antennas
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t antenna_status_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	u32 status_0_31;
+	u32 status_63_32;
+	u32 status_95_64;
+	u32 status_127_96;
+
+	status_0_31 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_STATUS_31_0_ADDR,
+				 RADIO_CDC_STATUS_31_0_OFFSET,
+				 lower_32_bits(RADIO_CDC_STATUS_31_0_MASK));
+	status_63_32 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_STATUS_63_32_ADDR,
+				 RADIO_CDC_STATUS_63_32_OFFSET,
+				 lower_32_bits(RADIO_CDC_STATUS_63_32_MASK));
+	status_95_64 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_STATUS_95_64_ADDR,
+				 RADIO_CDC_STATUS_95_64_OFFSET,
+				 lower_32_bits(RADIO_CDC_STATUS_95_64_MASK));
+	status_127_96 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_STATUS_127_96_ADDR,
+				 RADIO_CDC_STATUS_127_96_OFFSET,
+				 lower_32_bits(RADIO_CDC_STATUS_127_96_MASK));
+
+	return sprintf(buf, "0x%08x 0x%08x 0x%08x 0x%08x\n",
+		       status_0_31, status_63_32, status_95_64, status_127_96);
+}
+static DEVICE_ATTR_RO(antenna_status);
+
+/**
+ * antenna_error_show - Returns the error for all antennas
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the ID number string
+ *
+ * Returns the traffic gen's error for all antennas
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t antenna_error_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	u32 error_0_31;
+	u32 error_63_32;
+	u32 error_95_64;
+	u32 error_127_96;
+
+	error_0_31 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_ERROR_31_0_ADDR,
+				 RADIO_CDC_ERROR_31_0_OFFSET,
+				 lower_32_bits(RADIO_CDC_ERROR_31_0_MASK));
+	error_63_32 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_ERROR_63_32_ADDR,
+				 RADIO_CDC_ERROR_63_32_OFFSET,
+				 lower_32_bits(RADIO_CDC_ERROR_63_32_MASK));
+	error_95_64 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_ERROR_95_64_ADDR,
+				 RADIO_CDC_ERROR_95_64_OFFSET,
+				 lower_32_bits(RADIO_CDC_ERROR_95_64_MASK));
+	error_127_96 =
+	utils_sysfs_show_wrapper(dev, RADIO_CDC_ERROR_127_96_ADDR,
+				 RADIO_CDC_ERROR_127_96_OFFSET,
+				 lower_32_bits(RADIO_CDC_ERROR_127_96_MASK));
+
+	return sprintf(buf, "0x%08x 0x%08x 0x%08x 0x%08x\n",
+		       error_0_31, error_63_32, error_95_64, error_127_96);
+}
+static DEVICE_ATTR_RO(antenna_error);
+
+/**
+ * framer_packet_size_show - Returns the size of the framer's packet
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the loopback status
+ *
+ * Reads and writes the traffic gen's framer packet size value
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t framer_packet_size_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	u32 packet_size;
+
+	packet_size = utils_sysfs_show_wrapper(dev, FRAM_PACKET_DATA_SIZE_ADDR,
+					       FRAM_PACKET_DATA_SIZE_OFFSET,
+					       FRAM_PACKET_DATA_SIZE_MASK);
+	return sprintf(buf, "%d\n", packet_size);
+}
+
+/**
+ * framer_packet_size_store - Writes to the framer's packet size register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's framer packet
+ * size value to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t framer_packet_size_store(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	u32 packet_size;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &packet_size);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, FRAM_PACKET_DATA_SIZE_ADDR,
+				  FRAM_PACKET_DATA_SIZE_OFFSET,
+				  FRAM_PACKET_DATA_SIZE_MASK, packet_size);
+	return count;
+}
+static DEVICE_ATTR_RW(framer_packet_size);
+
+/**
+ * framer_pause_size_show - Returns the size of the framer's pause
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the loopback status
+ *
+ * Reads and writes the traffic gen's framer pause size value
+ *
+ * Return: The number of characters printed on success
+ */
+static ssize_t framer_pause_size_show(struct device *dev,
+				      struct device_attribute *attr, char *buf)
+{
+	u32 pause_size;
+
+	pause_size = utils_sysfs_show_wrapper(dev, FRAM_PAUSE_DATA_SIZE_ADDR,
+					      FRAM_PAUSE_DATA_SIZE_OFFSET,
+					      FRAM_PAUSE_DATA_SIZE_MASK);
+	return sprintf(buf, "%d\n", pause_size);
+}
+
+/**
+ * framer_pause_size_store - Writes to the framer's pause size register
+ * @dev:	The device's structure
+ * @attr:	The attributes of the kernel object
+ * @buf:	The buffer containing the timeout value
+ * @count:	The number of characters typed by the user
+ *
+ * Reads the user input and accordingly writes the traffic gens's framer pause
+ * size value to the sysfs entry
+ *
+ * Return: The number of characters of the entry (count) on success
+ */
+static ssize_t framer_pause_size_store(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t count)
+{
+	u32 pause_size;
+	int ret;
+
+	ret = kstrtouint(buf, 10, &pause_size);
+	if (ret)
+		return ret;
+	utils_sysfs_store_wrapper(dev, FRAM_PAUSE_DATA_SIZE_ADDR,
+				  FRAM_PAUSE_DATA_SIZE_OFFSET,
+				  FRAM_PAUSE_DATA_SIZE_MASK, pause_size);
+	return count;
+}
+static DEVICE_ATTR_RW(framer_pause_size);
+
+static struct attribute *xroe_traffic_gen_attrs[] = {
+	&dev_attr_radio_id.attr,
+	&dev_attr_timeout_enable.attr,
+	&dev_attr_timeout_status.attr,
+	&dev_attr_timeout_value.attr,
+	&dev_attr_ledmode.attr,
+	&dev_attr_ledgpio.attr,
+	&dev_attr_dip_status.attr,
+	&dev_attr_sw_trigger.attr,
+	&dev_attr_radio_enable.attr,
+	&dev_attr_radio_error.attr,
+	&dev_attr_radio_status.attr,
+	&dev_attr_radio_loopback.attr,
+	&dev_attr_radio_sink_enable.attr,
+	&dev_attr_antenna_status.attr,
+	&dev_attr_antenna_error.attr,
+	&dev_attr_framer_packet_size.attr,
+	&dev_attr_framer_pause_size.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(xroe_traffic_gen);
+
+/**
+ * xroe_traffic_gen_sysfs_init - Creates the xroe sysfs directory and entries
+ * @dev:	The device's structure
+ *
+ * Return: 0 on success, negative value in case of failure to
+ * create the sysfs group
+ *
+ * Creates the xroetrafficgen sysfs directory and entries
+ */
+int xroe_traffic_gen_sysfs_init(struct device *dev)
+{
+	int ret;
+
+	dev->groups = xroe_traffic_gen_groups;
+	ret = sysfs_create_group(&dev->kobj, *xroe_traffic_gen_groups);
+	if (ret)
+		dev_err(dev, "sysfs creation failed\n");
+
+	return ret;
+}
+
+/**
+ * xroe_traffic_gen_sysfs_exit - Deletes the xroe sysfs directory and entries
+ * @dev:	The device's structure
+ *
+ * Deletes the xroetrafficgen sysfs directory and entries
+ */
+void xroe_traffic_gen_sysfs_exit(struct device *dev)
+{
+	sysfs_remove_group(&dev->kobj, *xroe_traffic_gen_groups);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/xroe-traffic-gen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/xroe-traffic-gen.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/stat.h>
+#include <linux/sysfs.h>
+#include "xroe-traffic-gen.h"
+
+#define DRIVER_NAME "xroe_traffic_gen"
+
+static struct platform_driver xroe_traffic_gen_driver;
+
+/**
+ * xroe_traffic_gen_probe - Probes the device tree to locate the traffic gen
+ * block
+ * @pdev:	The structure containing the device's details
+ *
+ * Probes the device tree to locate the traffic gen block and maps it to
+ * the kernel virtual memory space
+ *
+ * Return: 0 on success or a negative errno on error.
+ */
+static int xroe_traffic_gen_probe(struct platform_device *pdev)
+{
+	struct xroe_traffic_gen_local *lp;
+	struct resource *r_mem; /* IO mem resources */
+	struct device *dev = &pdev->dev;
+
+	lp = devm_kzalloc(&pdev->dev, sizeof(*lp), GFP_KERNEL);
+	if (!lp)
+		return -ENOMEM;
+
+	/* Get iospace for the device */
+	/*
+	 * TODO: Use platform_get_resource_byname() instead when the DT entry
+	 * of the traffic gen block has been finalised (when it gets out of
+	 * the development stage).
+	 */
+	r_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	lp->base_addr = devm_ioremap_resource(&pdev->dev, r_mem);
+	if (IS_ERR(lp->base_addr))
+		return PTR_ERR(lp->base_addr);
+
+	dev_set_drvdata(dev, lp);
+	xroe_traffic_gen_sysfs_init(dev);
+	return 0;
+}
+
+/**
+ * xroe_traffic_gen_remove - Removes the sysfs entries created by the driver
+ * @pdev:	The structure containing the device's details
+ *
+ * Removes the sysfs entries created by the driver
+ *
+ * Return: 0
+ */
+static int xroe_traffic_gen_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+
+	xroe_traffic_gen_sysfs_exit(dev);
+	return 0;
+}
+
+/**
+ * xroe_traffic_gen_init - Registers the driver
+ *
+ * Return: 0 on success, -1 on allocation error
+ *
+ * Registers the traffic gen driver and creates the sysfs entries related
+ * to it
+ */
+static int __init xroe_traffic_gen_init(void)
+{
+	int ret;
+
+	pr_info("XROE traffic generator driver init\n");
+	ret = platform_driver_register(&xroe_traffic_gen_driver);
+	return ret;
+}
+
+/**
+ * xroe_traffic_gen_exit - Destroys the driver
+ *
+ * Unregisters the traffic gen driver
+ */
+static void __exit xroe_traffic_gen_exit(void)
+{
+	platform_driver_unregister(&xroe_traffic_gen_driver);
+	pr_debug("XROE traffic generator driver exit\n");
+}
+
+static const struct of_device_id xroe_traffic_gen_of_match[] = {
+	{ .compatible = "xlnx,roe-traffic-gen-1.0", },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, xroe_traffic_gen_of_match);
+
+static struct platform_driver xroe_traffic_gen_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table	= xroe_traffic_gen_of_match,
+	},
+	.probe = xroe_traffic_gen_probe,
+	.remove = xroe_traffic_gen_remove,
+};
+
+module_init(xroe_traffic_gen_init);
+module_exit(xroe_traffic_gen_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("Xilinx Radio over Ethernet Traffic Generator driver");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/staging/xroetrafficgen/xroe-traffic-gen.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/staging/xroetrafficgen/xroe-traffic-gen.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Vasileios Bimpikas <vasileios.bimpikas@xilinx.com>
+ */
+
+struct xroe_traffic_gen_local {
+	void __iomem *base_addr;
+};
+
+enum { XROE_SIZE_MAX = 15 };
+
+int xroe_traffic_gen_sysfs_init(struct device *dev);
+void xroe_traffic_gen_sysfs_exit(struct device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/iscsi/iscsi_target.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/iscsi/iscsi_target.c
@@ -4086,9 +4086,12 @@
 	list_for_each_entry_safe(cmd, cmd_tmp, &tmp_list, i_conn_node) {
 		struct se_cmd *se_cmd = &cmd->se_cmd;
 
-		if (se_cmd->se_tfo != NULL) {
-			spin_lock_irq(&se_cmd->t_state_lock);
-			if (se_cmd->transport_state & CMD_T_ABORTED) {
+		if (!se_cmd->se_tfo)
+			continue;
+
+		spin_lock_irq(&se_cmd->t_state_lock);
+		if (se_cmd->transport_state & CMD_T_ABORTED) {
+			if (!(se_cmd->transport_state & CMD_T_TAS))
 				/*
 				 * LIO's abort path owns the cleanup for this,
 				 * so put it back on the list and let
@@ -4096,11 +4099,10 @@
 				 */
 				list_move_tail(&cmd->i_conn_node,
 					       &conn->conn_cmd_list);
-			} else {
-				se_cmd->transport_state |= CMD_T_FABRIC_STOP;
-			}
-			spin_unlock_irq(&se_cmd->t_state_lock);
+		} else {
+			se_cmd->transport_state |= CMD_T_FABRIC_STOP;
 		}
+		spin_unlock_irq(&se_cmd->t_state_lock);
 	}
 	spin_unlock_bh(&conn->cmd_lock);
 
@@ -4385,6 +4387,9 @@
 	iscsit_stop_time2retain_timer(sess);
 	spin_unlock_bh(&se_tpg->session_lock);
 
+	if (sess->sess_ops->ErrorRecoveryLevel == 2)
+		iscsit_free_connection_recovery_entries(sess);
+
 	/*
 	 * transport_deregister_session_configfs() will clear the
 	 * struct se_node_acl->nacl_sess pointer now as a iscsi_np process context
@@ -4408,9 +4413,6 @@
 
 	transport_deregister_session(sess->se_sess);
 
-	if (sess->sess_ops->ErrorRecoveryLevel == 2)
-		iscsit_free_connection_recovery_entries(sess);
-
 	iscsit_free_all_ooo_cmdsns(sess);
 
 	spin_lock_bh(&se_tpg->session_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/iscsi/iscsi_target_configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/iscsi/iscsi_target_configfs.c
@@ -507,102 +507,102 @@
 	spin_lock_bh(&se_nacl->nacl_sess_lock);
 	se_sess = se_nacl->nacl_sess;
 	if (!se_sess) {
-		rb += sprintf(page+rb, "No active iSCSI Session for Initiator"
+		rb += sysfs_emit_at(page, rb, "No active iSCSI Session for Initiator"
 			" Endpoint: %s\n", se_nacl->initiatorname);
 	} else {
 		sess = se_sess->fabric_sess_ptr;
 
-		rb += sprintf(page+rb, "InitiatorName: %s\n",
+		rb += sysfs_emit_at(page, rb, "InitiatorName: %s\n",
 			sess->sess_ops->InitiatorName);
-		rb += sprintf(page+rb, "InitiatorAlias: %s\n",
+		rb += sysfs_emit_at(page, rb, "InitiatorAlias: %s\n",
 			sess->sess_ops->InitiatorAlias);
 
-		rb += sprintf(page+rb,
+		rb += sysfs_emit_at(page, rb,
 			      "LIO Session ID: %u   ISID: 0x%6ph  TSIH: %hu  ",
 			      sess->sid, sess->isid, sess->tsih);
-		rb += sprintf(page+rb, "SessionType: %s\n",
+		rb += sysfs_emit_at(page, rb, "SessionType: %s\n",
 				(sess->sess_ops->SessionType) ?
 				"Discovery" : "Normal");
-		rb += sprintf(page+rb, "Session State: ");
+		rb += sysfs_emit_at(page, rb, "Session State: ");
 		switch (sess->session_state) {
 		case TARG_SESS_STATE_FREE:
-			rb += sprintf(page+rb, "TARG_SESS_FREE\n");
+			rb += sysfs_emit_at(page, rb, "TARG_SESS_FREE\n");
 			break;
 		case TARG_SESS_STATE_ACTIVE:
-			rb += sprintf(page+rb, "TARG_SESS_STATE_ACTIVE\n");
+			rb += sysfs_emit_at(page, rb, "TARG_SESS_STATE_ACTIVE\n");
 			break;
 		case TARG_SESS_STATE_LOGGED_IN:
-			rb += sprintf(page+rb, "TARG_SESS_STATE_LOGGED_IN\n");
+			rb += sysfs_emit_at(page, rb, "TARG_SESS_STATE_LOGGED_IN\n");
 			break;
 		case TARG_SESS_STATE_FAILED:
-			rb += sprintf(page+rb, "TARG_SESS_STATE_FAILED\n");
+			rb += sysfs_emit_at(page, rb, "TARG_SESS_STATE_FAILED\n");
 			break;
 		case TARG_SESS_STATE_IN_CONTINUE:
-			rb += sprintf(page+rb, "TARG_SESS_STATE_IN_CONTINUE\n");
+			rb += sysfs_emit_at(page, rb, "TARG_SESS_STATE_IN_CONTINUE\n");
 			break;
 		default:
-			rb += sprintf(page+rb, "ERROR: Unknown Session"
+			rb += sysfs_emit_at(page, rb, "ERROR: Unknown Session"
 					" State!\n");
 			break;
 		}
 
-		rb += sprintf(page+rb, "---------------------[iSCSI Session"
+		rb += sysfs_emit_at(page, rb, "---------------------[iSCSI Session"
 				" Values]-----------------------\n");
-		rb += sprintf(page+rb, "  CmdSN/WR  :  CmdSN/WC  :  ExpCmdSN"
+		rb += sysfs_emit_at(page, rb, "  CmdSN/WR  :  CmdSN/WC  :  ExpCmdSN"
 				"  :  MaxCmdSN  :     ITT    :     TTT\n");
 		max_cmd_sn = (u32) atomic_read(&sess->max_cmd_sn);
-		rb += sprintf(page+rb, " 0x%08x   0x%08x   0x%08x   0x%08x"
+		rb += sysfs_emit_at(page, rb, " 0x%08x   0x%08x   0x%08x   0x%08x"
 				"   0x%08x   0x%08x\n",
 			sess->cmdsn_window,
 			(max_cmd_sn - sess->exp_cmd_sn) + 1,
 			sess->exp_cmd_sn, max_cmd_sn,
 			sess->init_task_tag, sess->targ_xfer_tag);
-		rb += sprintf(page+rb, "----------------------[iSCSI"
+		rb += sysfs_emit_at(page, rb, "----------------------[iSCSI"
 				" Connections]-------------------------\n");
 
 		spin_lock(&sess->conn_lock);
 		list_for_each_entry(conn, &sess->sess_conn_list, conn_list) {
-			rb += sprintf(page+rb, "CID: %hu  Connection"
+			rb += sysfs_emit_at(page, rb, "CID: %hu  Connection"
 					" State: ", conn->cid);
 			switch (conn->conn_state) {
 			case TARG_CONN_STATE_FREE:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_FREE\n");
 				break;
 			case TARG_CONN_STATE_XPT_UP:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_XPT_UP\n");
 				break;
 			case TARG_CONN_STATE_IN_LOGIN:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_IN_LOGIN\n");
 				break;
 			case TARG_CONN_STATE_LOGGED_IN:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_LOGGED_IN\n");
 				break;
 			case TARG_CONN_STATE_IN_LOGOUT:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_IN_LOGOUT\n");
 				break;
 			case TARG_CONN_STATE_LOGOUT_REQUESTED:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_LOGOUT_REQUESTED\n");
 				break;
 			case TARG_CONN_STATE_CLEANUP_WAIT:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"TARG_CONN_STATE_CLEANUP_WAIT\n");
 				break;
 			default:
-				rb += sprintf(page+rb,
+				rb += sysfs_emit_at(page, rb,
 					"ERROR: Unknown Connection State!\n");
 				break;
 			}
 
-			rb += sprintf(page+rb, "   Address %pISc %s", &conn->login_sockaddr,
+			rb += sysfs_emit_at(page, rb, "   Address %pISc %s", &conn->login_sockaddr,
 				(conn->network_transport == ISCSI_TCP) ?
 				"TCP" : "SCTP");
-			rb += sprintf(page+rb, "  StatSN: 0x%08x\n",
+			rb += sysfs_emit_at(page, rb, "  StatSN: 0x%08x\n",
 				conn->stat_sn);
 		}
 		spin_unlock(&sess->conn_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/iscsi/iscsi_target_nego.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/iscsi/iscsi_target_nego.c
@@ -1071,6 +1071,7 @@
 	iscsi_target_set_sock_callbacks(conn);
 
 	login->np = np;
+	conn->tpg = NULL;
 
 	login_req = (struct iscsi_login_req *) login->req;
 	payload_length = ntoh24(login_req->dlength);
@@ -1138,7 +1139,6 @@
 	 */
 	sessiontype = strncmp(s_buf, DISCOVERY, 9);
 	if (!sessiontype) {
-		conn->tpg = iscsit_global->discovery_tpg;
 		if (!login->leading_connection)
 			goto get_target;
 
@@ -1155,9 +1155,11 @@
 		 * Serialize access across the discovery struct iscsi_portal_group to
 		 * process login attempt.
 		 */
+		conn->tpg = iscsit_global->discovery_tpg;
 		if (iscsit_access_np(np, conn->tpg) < 0) {
 			iscsit_tx_login_rsp(conn, ISCSI_STATUS_CLS_TARGET_ERR,
 				ISCSI_LOGIN_STATUS_SVC_UNAVAILABLE);
+			conn->tpg = NULL;
 			ret = -1;
 			goto out;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/iscsi/iscsi_target_parameters.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/iscsi/iscsi_target_parameters.c
@@ -1262,18 +1262,20 @@
 		return param;
 
 	if (!(param->phase & phase)) {
-		pr_err("Key \"%s\" may not be negotiated during ",
-				param->name);
+		char *phase_name;
+
 		switch (phase) {
 		case PHASE_SECURITY:
-			pr_debug("Security phase.\n");
+			phase_name = "Security";
 			break;
 		case PHASE_OPERATIONAL:
-			pr_debug("Operational phase.\n");
+			phase_name = "Operational";
 			break;
 		default:
-			pr_debug("Unknown phase.\n");
+			phase_name = "Unknown";
 		}
+		pr_err("Key \"%s\" may not be negotiated during %s phase.\n",
+				param->name, phase_name);
 		return NULL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/iscsi/iscsi_target_tpg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/iscsi/iscsi_target_tpg.c
@@ -443,6 +443,9 @@
 				break;
 		}
 		spin_unlock(&tpg->tpg_np_lock);
+
+		if (match)
+			break;
 	}
 	spin_unlock(&tiqn->tiqn_tpg_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/loopback/tcm_loop.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/loopback/tcm_loop.c
@@ -397,6 +397,7 @@
 	ret = device_register(&tl_hba->dev);
 	if (ret) {
 		pr_err("device_register() failed for tl_hba->dev: %d\n", ret);
+		put_device(&tl_hba->dev);
 		return -ENODEV;
 	}
 
@@ -1073,7 +1074,7 @@
 	 */
 	ret = tcm_loop_setup_hba_bus(tl_hba, tcm_loop_hba_no_cnt);
 	if (ret)
-		goto out;
+		return ERR_PTR(ret);
 
 	sh = tl_hba->sh;
 	tcm_loop_hba_no_cnt++;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_alua.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_alua.c
@@ -1674,7 +1674,6 @@
 		pr_err("Maximum ALUA alua_tg_pt_gps_count:"
 			" 0x0000ffff reached\n");
 		spin_unlock(&dev->t10_alua.tg_pt_gps_lock);
-		kmem_cache_free(t10_alua_tg_pt_gp_cache, tg_pt_gp);
 		return -ENOSPC;
 	}
 again:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_configfs.c
@@ -3566,6 +3566,8 @@
 {
 	struct configfs_subsystem *subsys = &target_core_fabrics;
 	struct t10_alua_lu_gp *lu_gp;
+	struct cred *kern_cred;
+	const struct cred *old_cred;
 	int ret;
 
 	pr_debug("TARGET_CORE[0]: Loading Generic Kernel Storage"
@@ -3642,11 +3644,21 @@
 	if (ret < 0)
 		goto out;
 
+	/* We use the kernel credentials to access the target directory */
+	kern_cred = prepare_kernel_cred(&init_task);
+	if (!kern_cred) {
+		ret = -ENOMEM;
+		goto out;
+	}
+	old_cred = override_creds(kern_cred);
 	target_init_dbroot();
+	revert_creds(old_cred);
+	put_cred(kern_cred);
 
 	return 0;
 
 out:
+	target_xcopy_release_pt();
 	configfs_unregister_subsystem(subsys);
 	core_dev_release_virtual_lun0();
 	rd_module_exit();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_device.c
@@ -147,7 +147,6 @@
 	struct se_session *se_sess = se_cmd->se_sess;
 	struct se_node_acl *nacl = se_sess->se_node_acl;
 	struct se_tmr_req *se_tmr = se_cmd->se_tmr_req;
-	unsigned long flags;
 
 	rcu_read_lock();
 	deve = target_nacl_find_deve(nacl, se_cmd->orig_fe_lun);
@@ -178,10 +177,6 @@
 	se_cmd->se_dev = rcu_dereference_raw(se_lun->lun_se_dev);
 	se_tmr->tmr_dev = rcu_dereference_raw(se_lun->lun_se_dev);
 
-	spin_lock_irqsave(&se_tmr->tmr_dev->se_tmr_lock, flags);
-	list_add_tail(&se_tmr->tmr_list, &se_tmr->tmr_dev->dev_tmr_list);
-	spin_unlock_irqrestore(&se_tmr->tmr_dev->se_tmr_lock, flags);
-
 	return 0;
 }
 EXPORT_SYMBOL(transport_lookup_tmr_lun);
@@ -729,7 +724,7 @@
 
 	dev->queues = kcalloc(nr_cpu_ids, sizeof(*dev->queues), GFP_KERNEL);
 	if (!dev->queues) {
-		dev->transport->free_device(dev);
+		hba->backend->ops->free_device(dev);
 		return NULL;
 	}
 
@@ -772,6 +767,9 @@
 	INIT_LIST_HEAD(&dev->t10_alua.lba_map_list);
 	spin_lock_init(&dev->t10_alua.lba_map_lock);
 
+	INIT_WORK(&dev->delayed_cmd_work, target_do_delayed_work);
+	mutex_init(&dev->lun_reset_mutex);
+
 	dev->t10_wwn.t10_dev = dev;
 	/*
 	 * Use OpenFabrics IEEE Company ID: 00 14 05
@@ -848,7 +846,6 @@
 	attrib->unmap_granularity = q->limits.discard_granularity / block_size;
 	attrib->unmap_granularity_alignment = q->limits.discard_alignment /
 								block_size;
-	attrib->unmap_zeroes_data = !!(q->limits.max_write_zeroes_sectors);
 	return true;
 }
 EXPORT_SYMBOL(target_configure_unmap_from_queue);
@@ -873,7 +870,6 @@
 EXPORT_SYMBOL(target_to_linux_sector);
 
 struct devices_idr_iter {
-	struct config_item *prev_item;
 	int (*fn)(struct se_device *dev, void *data);
 	void *data;
 };
@@ -883,11 +879,9 @@
 {
 	struct devices_idr_iter *iter = data;
 	struct se_device *dev = p;
+	struct config_item *item;
 	int ret;
 
-	config_item_put(iter->prev_item);
-	iter->prev_item = NULL;
-
 	/*
 	 * We add the device early to the idr, so it can be used
 	 * by backend modules during configuration. We do not want
@@ -897,12 +891,13 @@
 	if (!target_dev_configured(dev))
 		return 0;
 
-	iter->prev_item = config_item_get_unless_zero(&dev->dev_group.cg_item);
-	if (!iter->prev_item)
+	item = config_item_get_unless_zero(&dev->dev_group.cg_item);
+	if (!item)
 		return 0;
 	mutex_unlock(&device_mutex);
 
 	ret = iter->fn(dev, iter->data);
+	config_item_put(item);
 
 	mutex_lock(&device_mutex);
 	return ret;
@@ -925,7 +920,6 @@
 	mutex_lock(&device_mutex);
 	ret = idr_for_each(&devices_idr, target_devices_idr_iter, &iter);
 	mutex_unlock(&device_mutex);
-	config_item_put(iter.prev_item);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_file.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_file.c
@@ -332,7 +332,7 @@
 		len += sg->length;
 	}
 
-	iov_iter_bvec(&iter, READ, bvec, sgl_nents, len);
+	iov_iter_bvec(&iter, is_write, bvec, sgl_nents, len);
 	if (is_write)
 		ret = vfs_iter_write(fd, &iter, &pos, 0);
 	else
@@ -469,7 +469,7 @@
 		len += se_dev->dev_attrib.block_size;
 	}
 
-	iov_iter_bvec(&iter, READ, bvec, nolb, len);
+	iov_iter_bvec(&iter, WRITE, bvec, nolb, len);
 	ret = vfs_iter_write(fd_dev->fd_file, &iter, &pos, 0);
 
 	kfree(bvec);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_internal.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_internal.h
@@ -151,6 +151,7 @@
 void	transport_clear_lun_ref(struct se_lun *);
 sense_reason_t	target_cmd_size_check(struct se_cmd *cmd, unsigned int size);
 void	target_qf_do_work(struct work_struct *work);
+void	target_do_delayed_work(struct work_struct *work);
 bool	target_check_wce(struct se_device *dev);
 bool	target_check_fua(struct se_device *dev);
 void	__target_execute_cmd(struct se_cmd *, bool);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_tmr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_tmr.c
@@ -50,15 +50,6 @@
 
 void core_tmr_release_req(struct se_tmr_req *tmr)
 {
-	struct se_device *dev = tmr->tmr_dev;
-	unsigned long flags;
-
-	if (dev) {
-		spin_lock_irqsave(&dev->se_tmr_lock, flags);
-		list_del_init(&tmr->tmr_list);
-		spin_unlock_irqrestore(&dev->se_tmr_lock, flags);
-	}
-
 	kfree(tmr);
 }
 
@@ -82,8 +73,8 @@
 {
 	struct se_session *sess = se_cmd->se_sess;
 
-	assert_spin_locked(&sess->sess_cmd_lock);
-	WARN_ON_ONCE(!irqs_disabled());
+	lockdep_assert_held(&sess->sess_cmd_lock);
+
 	/*
 	 * If command already reached CMD_T_COMPLETE state within
 	 * target_complete_cmd() or CMD_T_FABRIC_STOP due to shutdown,
@@ -156,13 +147,6 @@
 			se_cmd->state_active = false;
 			spin_unlock_irqrestore(&dev->queues[i].lock, flags);
 
-			/*
-			 * Ensure that this ABORT request is visible to the LU
-			 * RESET code.
-			 */
-			if (!tmr->tmr_dev)
-				WARN_ON_ONCE(transport_lookup_tmr_lun(tmr->task_cmd) < 0);
-
 			if (dev->transport->tmr_notify)
 				dev->transport->tmr_notify(dev, TMR_ABORT_TASK,
 							   &aborted_list);
@@ -204,14 +188,23 @@
 	 * LUN_RESET tmr..
 	 */
 	spin_lock_irqsave(&dev->se_tmr_lock, flags);
-	if (tmr)
-		list_del_init(&tmr->tmr_list);
 	list_for_each_entry_safe(tmr_p, tmr_pp, &dev->dev_tmr_list, tmr_list) {
+		if (tmr_p == tmr)
+			continue;
+
 		cmd = tmr_p->task_cmd;
 		if (!cmd) {
 			pr_err("Unable to locate struct se_cmd for TMR\n");
 			continue;
 		}
+
+		/*
+		 * We only execute one LUN_RESET at a time so we can't wait
+		 * on them below.
+		 */
+		if (tmr_p->function == TMR_LUN_RESET)
+			continue;
+
 		/*
 		 * If this function was called with a valid pr_res_key
 		 * parameter (eg: for PROUT PREEMPT_AND_ABORT service action
@@ -234,6 +227,7 @@
 		}
 
 		list_move_tail(&tmr_p->tmr_list, &drain_tmr_list);
+		tmr_p->tmr_dev = NULL;
 	}
 	spin_unlock_irqrestore(&dev->se_tmr_lock, flags);
 
@@ -394,14 +388,25 @@
 				tmr_nacl->initiatorname);
 		}
 	}
+
+
+	/*
+	 * We only allow one reset or preempt and abort to execute at a time
+	 * to prevent one call from claiming all the cmds causing a second
+	 * call from returning while cmds it should have waited on are still
+	 * running.
+	 */
+	mutex_lock(&dev->lun_reset_mutex);
+
 	pr_debug("LUN_RESET: %s starting for [%s], tas: %d\n",
 		(preempt_and_abort_list) ? "Preempt" : "TMR",
 		dev->transport->name, tas);
-
 	core_tmr_drain_tmr_list(dev, tmr, preempt_and_abort_list);
 	core_tmr_drain_state_list(dev, prout_cmd, tmr_sess, tas,
 				preempt_and_abort_list);
 
+	mutex_unlock(&dev->lun_reset_mutex);
+
 	/*
 	 * Clear any legacy SPC-2 reservation when called during
 	 * LOGICAL UNIT RESET
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_transport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_transport.c
@@ -676,6 +676,21 @@
 	spin_unlock_irqrestore(&dev->queues[cmd->cpuid].lock, flags);
 }
 
+static void target_remove_from_tmr_list(struct se_cmd *cmd)
+{
+	struct se_device *dev = NULL;
+	unsigned long flags;
+
+	if (cmd->se_cmd_flags & SCF_SCSI_TMR_CDB)
+		dev = cmd->se_tmr_req->tmr_dev;
+
+	if (dev) {
+		spin_lock_irqsave(&dev->se_tmr_lock, flags);
+		if (cmd->se_tmr_req->tmr_dev)
+			list_del_init(&cmd->se_tmr_req->tmr_list);
+		spin_unlock_irqrestore(&dev->se_tmr_lock, flags);
+	}
+}
 /*
  * This function is called by the target core after the target core has
  * finished processing a SCSI command or SCSI TMF. Both the regular command
@@ -687,13 +702,6 @@
 {
 	unsigned long flags;
 
-	target_remove_from_state_list(cmd);
-
-	/*
-	 * Clear struct se_cmd->se_lun before the handoff to FE.
-	 */
-	cmd->se_lun = NULL;
-
 	spin_lock_irqsave(&cmd->t_state_lock, flags);
 	/*
 	 * Determine if frontend context caller is requesting the stopping of
@@ -728,8 +736,16 @@
 	if (!lun)
 		return;
 
+	target_remove_from_state_list(cmd);
+	target_remove_from_tmr_list(cmd);
+
 	if (cmpxchg(&cmd->lun_ref_active, true, false))
 		percpu_ref_put(&lun->lun_ref);
+
+	/*
+	 * Clear struct se_cmd->se_lun before the handoff to FE.
+	 */
+	cmd->se_lun = NULL;
 }
 
 static void target_complete_failure_work(struct work_struct *work)
@@ -2173,32 +2189,35 @@
 	 */
 	switch (cmd->sam_task_attr) {
 	case TCM_HEAD_TAG:
+		atomic_inc_mb(&dev->non_ordered);
 		pr_debug("Added HEAD_OF_QUEUE for CDB: 0x%02x\n",
 			 cmd->t_task_cdb[0]);
 		return false;
 	case TCM_ORDERED_TAG:
-		atomic_inc_mb(&dev->dev_ordered_sync);
+		atomic_inc_mb(&dev->delayed_cmd_count);
 
 		pr_debug("Added ORDERED for CDB: 0x%02x to ordered list\n",
 			 cmd->t_task_cdb[0]);
-
-		/*
-		 * Execute an ORDERED command if no other older commands
-		 * exist that need to be completed first.
-		 */
-		if (!atomic_read(&dev->simple_cmds))
-			return false;
 		break;
 	default:
 		/*
 		 * For SIMPLE and UNTAGGED Task Attribute commands
 		 */
-		atomic_inc_mb(&dev->simple_cmds);
+		atomic_inc_mb(&dev->non_ordered);
+
+		if (atomic_read(&dev->delayed_cmd_count) == 0)
+			return false;
 		break;
 	}
 
-	if (atomic_read(&dev->dev_ordered_sync) == 0)
-		return false;
+	if (cmd->sam_task_attr != TCM_ORDERED_TAG) {
+		atomic_inc_mb(&dev->delayed_cmd_count);
+		/*
+		 * We will account for this when we dequeue from the delayed
+		 * list.
+		 */
+		atomic_dec_mb(&dev->non_ordered);
+	}
 
 	spin_lock(&dev->delayed_cmd_lock);
 	list_add_tail(&cmd->se_delayed_node, &dev->delayed_cmd_list);
@@ -2206,6 +2225,12 @@
 
 	pr_debug("Added CDB: 0x%02x Task Attr: 0x%02x to delayed CMD listn",
 		cmd->t_task_cdb[0], cmd->sam_task_attr);
+	/*
+	 * We may have no non ordered cmds when this function started or we
+	 * could have raced with the last simple/head cmd completing, so kick
+	 * the delayed handler here.
+	 */
+	schedule_work(&dev->delayed_cmd_work);
 	return true;
 }
 
@@ -2243,29 +2268,48 @@
  * Process all commands up to the last received ORDERED task attribute which
  * requires another blocking boundary
  */
-static void target_restart_delayed_cmds(struct se_device *dev)
+void target_do_delayed_work(struct work_struct *work)
 {
-	for (;;) {
+	struct se_device *dev = container_of(work, struct se_device,
+					     delayed_cmd_work);
+
+	spin_lock(&dev->delayed_cmd_lock);
+	while (!dev->ordered_sync_in_progress) {
 		struct se_cmd *cmd;
 
-		spin_lock(&dev->delayed_cmd_lock);
-		if (list_empty(&dev->delayed_cmd_list)) {
-			spin_unlock(&dev->delayed_cmd_lock);
+		if (list_empty(&dev->delayed_cmd_list))
 			break;
-		}
 
 		cmd = list_entry(dev->delayed_cmd_list.next,
 				 struct se_cmd, se_delayed_node);
+
+		if (cmd->sam_task_attr == TCM_ORDERED_TAG) {
+			/*
+			 * Check if we started with:
+			 * [ordered] [simple] [ordered]
+			 * and we are now at the last ordered so we have to wait
+			 * for the simple cmd.
+			 */
+			if (atomic_read(&dev->non_ordered) > 0)
+				break;
+
+			dev->ordered_sync_in_progress = true;
+		}
+
 		list_del(&cmd->se_delayed_node);
+		atomic_dec_mb(&dev->delayed_cmd_count);
 		spin_unlock(&dev->delayed_cmd_lock);
 
+		if (cmd->sam_task_attr != TCM_ORDERED_TAG)
+			atomic_inc_mb(&dev->non_ordered);
+
 		cmd->transport_state |= CMD_T_SENT;
 
 		__target_execute_cmd(cmd, true);
 
-		if (cmd->sam_task_attr == TCM_ORDERED_TAG)
-			break;
+		spin_lock(&dev->delayed_cmd_lock);
 	}
+	spin_unlock(&dev->delayed_cmd_lock);
 }
 
 /*
@@ -2283,14 +2327,17 @@
 		goto restart;
 
 	if (cmd->sam_task_attr == TCM_SIMPLE_TAG) {
-		atomic_dec_mb(&dev->simple_cmds);
+		atomic_dec_mb(&dev->non_ordered);
 		dev->dev_cur_ordered_id++;
 	} else if (cmd->sam_task_attr == TCM_HEAD_TAG) {
+		atomic_dec_mb(&dev->non_ordered);
 		dev->dev_cur_ordered_id++;
 		pr_debug("Incremented dev_cur_ordered_id: %u for HEAD_OF_QUEUE\n",
 			 dev->dev_cur_ordered_id);
 	} else if (cmd->sam_task_attr == TCM_ORDERED_TAG) {
-		atomic_dec_mb(&dev->dev_ordered_sync);
+		spin_lock(&dev->delayed_cmd_lock);
+		dev->ordered_sync_in_progress = false;
+		spin_unlock(&dev->delayed_cmd_lock);
 
 		dev->dev_cur_ordered_id++;
 		pr_debug("Incremented dev_cur_ordered_id: %u for ORDERED\n",
@@ -2299,7 +2346,8 @@
 	cmd->se_cmd_flags &= ~SCF_TASK_ATTR_SET;
 
 restart:
-	target_restart_delayed_cmds(dev);
+	if (atomic_read(&dev->delayed_cmd_count) > 0)
+		schedule_work(&dev->delayed_cmd_work);
 }
 
 static void transport_complete_qf(struct se_cmd *cmd)
@@ -3520,6 +3568,10 @@
 	unsigned long flags;
 	bool aborted = false;
 
+	spin_lock_irqsave(&cmd->se_dev->se_tmr_lock, flags);
+	list_add_tail(&cmd->se_tmr_req->tmr_list, &cmd->se_dev->dev_tmr_list);
+	spin_unlock_irqrestore(&cmd->se_dev->se_tmr_lock, flags);
+
 	spin_lock_irqsave(&cmd->t_state_lock, flags);
 	if (cmd->transport_state & CMD_T_ABORTED) {
 		aborted = true;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/target/target_core_user.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/target/target_core_user.c
@@ -20,6 +20,7 @@
 #include <linux/configfs.h>
 #include <linux/mutex.h>
 #include <linux/workqueue.h>
+#include <linux/pagemap.h>
 #include <net/genetlink.h>
 #include <scsi/scsi_common.h>
 #include <scsi/scsi_proto.h>
@@ -1660,17 +1661,37 @@
 static u32 tcmu_blocks_release(struct tcmu_dev *udev, unsigned long first,
 				unsigned long last)
 {
-	XA_STATE(xas, &udev->data_pages, first * udev->data_pages_per_blk);
 	struct page *page;
+	unsigned long dpi;
 	u32 pages_freed = 0;
 
-	xas_lock(&xas);
-	xas_for_each(&xas, page, (last + 1) * udev->data_pages_per_blk - 1) {
-		xas_store(&xas, NULL);
+	first = first * udev->data_pages_per_blk;
+	last = (last + 1) * udev->data_pages_per_blk - 1;
+	xa_for_each_range(&udev->data_pages, dpi, page, first, last) {
+		xa_erase(&udev->data_pages, dpi);
+		/*
+		 * While reaching here there may be page faults occurring on
+		 * the to-be-released pages. A race condition may occur if
+		 * unmap_mapping_range() is called before page faults on these
+		 * pages have completed; a valid but stale map is created.
+		 *
+		 * If another command subsequently runs and needs to extend
+		 * dbi_thresh, it may reuse the slot corresponding to the
+		 * previous page in data_bitmap. Though we will allocate a new
+		 * page for the slot in data_area, no page fault will happen
+		 * because we have a valid map. Therefore the command's data
+		 * will be lost.
+		 *
+		 * We lock and unlock pages that are to be released to ensure
+		 * all page faults have completed. This way
+		 * unmap_mapping_range() can ensure stale maps are cleanly
+		 * removed.
+		 */
+		lock_page(page);
+		unlock_page(page);
 		__free_page(page);
 		pages_freed++;
 	}
-	xas_unlock(&xas);
 
 	atomic_sub(pages_freed, &global_page_count);
 
@@ -1821,6 +1842,8 @@
 	mutex_lock(&udev->cmdr_lock);
 	page = xa_load(&udev->data_pages, dpi);
 	if (likely(page)) {
+		get_page(page);
+		lock_page(page);
 		mutex_unlock(&udev->cmdr_lock);
 		return page;
 	}
@@ -1862,6 +1885,7 @@
 	struct page *page;
 	unsigned long offset;
 	void *addr;
+	vm_fault_t ret = 0;
 
 	int mi = tcmu_find_mem_index(vmf->vma);
 	if (mi < 0)
@@ -1877,6 +1901,7 @@
 		/* For the vmalloc()ed cmd area pages */
 		addr = (void *)(unsigned long)info->mem[mi].addr + offset;
 		page = vmalloc_to_page(addr);
+		get_page(page);
 	} else {
 		uint32_t dpi;
 
@@ -1885,11 +1910,11 @@
 		page = tcmu_try_get_data_page(udev, dpi);
 		if (!page)
 			return VM_FAULT_SIGBUS;
+		ret = VM_FAULT_LOCKED;
 	}
 
-	get_page(page);
 	vmf->page = page;
-	return 0;
+	return ret;
 }
 
 static const struct vm_operations_struct tcmu_vm_ops = {
@@ -2104,7 +2129,7 @@
 	}
 
 	ret = genlmsg_multicast_allns(&tcmu_genl_family, skb, 0,
-				      TCMU_MCGRP_CONFIG, GFP_KERNEL);
+				      TCMU_MCGRP_CONFIG);
 
 	/* Wait during an add as the listener may not be up yet */
 	if (ret == 0 ||
@@ -3152,12 +3177,22 @@
 			udev->dbi_max = block;
 		}
 
+		/*
+		 * Release the block pages.
+		 *
+		 * Also note that since tcmu_vma_fault() gets an extra page
+		 * refcount, tcmu_blocks_release() won't free pages if pages
+		 * are mapped. This means it is safe to call
+		 * tcmu_blocks_release() before unmap_mapping_range() which
+		 * drops the refcount of any pages it unmaps and thus releases
+		 * them.
+		 */
+		pages_freed = tcmu_blocks_release(udev, start, end - 1);
+
 		/* Here will truncate the data area from off */
 		off = udev->data_off + (loff_t)start * udev->data_blk_size;
 		unmap_mapping_range(udev->inode->i_mapping, off, 0, 1);
 
-		/* Release the block pages */
-		pages_freed = tcmu_blocks_release(udev, start, end - 1);
 		mutex_unlock(&udev->cmdr_lock);
 
 		total_pages_freed += pages_freed;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/amdtee/amdtee_if.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/amdtee/amdtee_if.h
@@ -118,16 +118,18 @@
 
 /**
  * struct tee_cmd_load_ta - load Trusted Application (TA) binary into TEE
- * @low_addr:    [in] bits [31:0] of the physical address of the TA binary
- * @hi_addr:     [in] bits [63:32] of the physical address of the TA binary
- * @size:        [in] size of TA binary in bytes
- * @ta_handle:   [out] return handle of the loaded TA
+ * @low_addr:       [in] bits [31:0] of the physical address of the TA binary
+ * @hi_addr:        [in] bits [63:32] of the physical address of the TA binary
+ * @size:           [in] size of TA binary in bytes
+ * @ta_handle:      [out] return handle of the loaded TA
+ * @return_origin:  [out] origin of return code after TEE processing
  */
 struct tee_cmd_load_ta {
 	u32 low_addr;
 	u32 hi_addr;
 	u32 size;
 	u32 ta_handle;
+	u32 return_origin;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/amdtee/call.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/amdtee/call.c
@@ -423,19 +423,23 @@
 	if (ret) {
 		arg->ret_origin = TEEC_ORIGIN_COMMS;
 		arg->ret = TEEC_ERROR_COMMUNICATION;
-	} else if (arg->ret == TEEC_SUCCESS) {
-		ret = get_ta_refcount(load_cmd.ta_handle);
-		if (!ret) {
-			arg->ret_origin = TEEC_ORIGIN_COMMS;
-			arg->ret = TEEC_ERROR_OUT_OF_MEMORY;
+	} else {
+		arg->ret_origin = load_cmd.return_origin;
 
-			/* Unload the TA on error */
-			unload_cmd.ta_handle = load_cmd.ta_handle;
-			psp_tee_process_cmd(TEE_CMD_ID_UNLOAD_TA,
-					    (void *)&unload_cmd,
-					    sizeof(unload_cmd), &ret);
-		} else {
-			set_session_id(load_cmd.ta_handle, 0, &arg->session);
+		if (arg->ret == TEEC_SUCCESS) {
+			ret = get_ta_refcount(load_cmd.ta_handle);
+			if (!ret) {
+				arg->ret_origin = TEEC_ORIGIN_COMMS;
+				arg->ret = TEEC_ERROR_OUT_OF_MEMORY;
+
+				/* Unload the TA on error */
+				unload_cmd.ta_handle = load_cmd.ta_handle;
+				psp_tee_process_cmd(TEE_CMD_ID_UNLOAD_TA,
+						    (void *)&unload_cmd,
+						    sizeof(unload_cmd), &ret);
+			} else {
+				set_session_id(load_cmd.ta_handle, 0, &arg->session);
+			}
 		}
 	}
 	mutex_unlock(&ta_refcount_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/amdtee/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/amdtee/core.c
@@ -203,9 +203,8 @@
 
 	*ta_size = roundup(fw->size, PAGE_SIZE);
 	*ta = (void *)__get_free_pages(GFP_KERNEL, get_order(*ta_size));
-	if (IS_ERR(*ta)) {
-		pr_err("%s: get_free_pages failed 0x%llx\n", __func__,
-		       (u64)*ta);
+	if (!*ta) {
+		pr_err("%s: get_free_pages failed\n", __func__);
 		rc = -ENOMEM;
 		goto rel_fw;
 	}
@@ -218,12 +217,12 @@
 	return rc;
 }
 
+/* mutex must be held by caller */
 static void destroy_session(struct kref *ref)
 {
 	struct amdtee_session *sess = container_of(ref, struct amdtee_session,
 						   refcount);
 
-	mutex_lock(&session_list_mutex);
 	list_del(&sess->list_node);
 	mutex_unlock(&session_list_mutex);
 	kfree(sess);
@@ -268,35 +267,36 @@
 		goto out;
 	}
 
+	/* Open session with loaded TA */
+	handle_open_session(arg, &session_info, param);
+	if (arg->ret != TEEC_SUCCESS) {
+		pr_err("open_session failed %d\n", arg->ret);
+		handle_unload_ta(ta_handle);
+		kref_put_mutex(&sess->refcount, destroy_session,
+			       &session_list_mutex);
+		goto out;
+	}
+
 	/* Find an empty session index for the given TA */
 	spin_lock(&sess->lock);
 	i = find_first_zero_bit(sess->sess_mask, TEE_NUM_SESSIONS);
-	if (i < TEE_NUM_SESSIONS)
+	if (i < TEE_NUM_SESSIONS) {
+		sess->session_info[i] = session_info;
+		set_session_id(ta_handle, i, &arg->session);
 		set_bit(i, sess->sess_mask);
+	}
 	spin_unlock(&sess->lock);
 
 	if (i >= TEE_NUM_SESSIONS) {
 		pr_err("reached maximum session count %d\n", TEE_NUM_SESSIONS);
+		handle_close_session(ta_handle, session_info);
 		handle_unload_ta(ta_handle);
-		kref_put(&sess->refcount, destroy_session);
+		kref_put_mutex(&sess->refcount, destroy_session,
+			       &session_list_mutex);
 		rc = -ENOMEM;
 		goto out;
 	}
 
-	/* Open session with loaded TA */
-	handle_open_session(arg, &session_info, param);
-	if (arg->ret != TEEC_SUCCESS) {
-		pr_err("open_session failed %d\n", arg->ret);
-		spin_lock(&sess->lock);
-		clear_bit(i, sess->sess_mask);
-		spin_unlock(&sess->lock);
-		handle_unload_ta(ta_handle);
-		kref_put(&sess->refcount, destroy_session);
-		goto out;
-	}
-
-	sess->session_info[i] = session_info;
-	set_session_id(ta_handle, i, &arg->session);
 out:
 	free_pages((u64)ta, get_order(ta_size));
 	return rc;
@@ -333,7 +333,7 @@
 	handle_close_session(ta_handle, session_info);
 	handle_unload_ta(ta_handle);
 
-	kref_put(&sess->refcount, destroy_session);
+	kref_put_mutex(&sess->refcount, destroy_session, &session_list_mutex);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/optee/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/optee/core.c
@@ -588,6 +588,7 @@
 	/* Unregister OP-TEE specific client devices on TEE bus */
 	optee_unregister_devices();
 
+	teedev_close_context(optee->ctx);
 	/*
 	 * Ask OP-TEE to free all cached shared memory objects to decrease
 	 * reference counters and also avoid wild pointers in secure world
@@ -633,6 +634,7 @@
 	struct optee *optee = NULL;
 	void *memremaped_shm = NULL;
 	struct tee_device *teedev;
+	struct tee_context *ctx;
 	u32 sec_caps;
 	int rc;
 
@@ -719,6 +721,12 @@
 	optee_supp_init(&optee->supp);
 	optee->memremaped_shm = memremaped_shm;
 	optee->pool = pool;
+	ctx = teedev_open(optee->teedev);
+	if (IS_ERR(ctx)) {
+		rc = PTR_ERR(ctx);
+		goto err;
+	}
+	optee->ctx = ctx;
 
 	/*
 	 * Ensure that there are no pre-existing shm objects before enabling
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/optee/device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/optee/device.c
@@ -60,7 +60,16 @@
 	kfree(optee_device);
 }
 
-static int optee_register_device(const uuid_t *device_uuid)
+static ssize_t need_supplicant_show(struct device *dev,
+				    struct device_attribute *attr,
+				    char *buf)
+{
+	return 0;
+}
+
+static DEVICE_ATTR_RO(need_supplicant);
+
+static int optee_register_device(const uuid_t *device_uuid, u32 func)
 {
 	struct tee_client_device *optee_device = NULL;
 	int rc;
@@ -80,10 +89,15 @@
 	rc = device_register(&optee_device->dev);
 	if (rc) {
 		pr_err("device registration failed, err: %d\n", rc);
-		kfree(optee_device);
+		put_device(&optee_device->dev);
+		return rc;
 	}
 
-	return rc;
+	if (func == PTA_CMD_GET_DEVICES_SUPP)
+		device_create_file(&optee_device->dev,
+				   &dev_attr_need_supplicant);
+
+	return 0;
 }
 
 static int __optee_enumerate_devices(u32 func)
@@ -143,7 +157,7 @@
 	num_devices = shm_size / sizeof(uuid_t);
 
 	for (idx = 0; idx < num_devices; idx++) {
-		rc = optee_register_device(&device_uuid[idx]);
+		rc = optee_register_device(&device_uuid[idx], func);
 		if (rc)
 			goto out_shm;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/optee/optee_private.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/optee/optee_private.h
@@ -70,6 +70,7 @@
  * struct optee - main service struct
  * @supp_teedev:	supplicant device
  * @teedev:		client device
+ * @ctx:		driver internal TEE context
  * @invoke_fn:		function to issue smc or hvc
  * @call_queue:		queue of threads waiting to call @invoke_fn
  * @wait_queue:		queue of threads from secure world waiting for a
@@ -87,6 +88,7 @@
 	struct tee_device *supp_teedev;
 	struct tee_device *teedev;
 	optee_invoke_fn *invoke_fn;
+	struct tee_context *ctx;
 	struct optee_call_queue call_queue;
 	struct optee_wait_queue wait_queue;
 	struct optee_supp supp;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/optee/rpc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/optee/rpc.c
@@ -285,6 +285,7 @@
 }
 
 static void handle_rpc_func_cmd_shm_alloc(struct tee_context *ctx,
+					  struct optee *optee,
 					  struct optee_msg_arg *arg,
 					  struct optee_call_ctx *call_ctx)
 {
@@ -314,7 +315,8 @@
 		shm = cmd_alloc_suppl(ctx, sz);
 		break;
 	case OPTEE_RPC_SHM_TYPE_KERNEL:
-		shm = tee_shm_alloc(ctx, sz, TEE_SHM_MAPPED | TEE_SHM_PRIV);
+		shm = tee_shm_alloc(optee->ctx, sz,
+				    TEE_SHM_MAPPED | TEE_SHM_PRIV);
 		break;
 	default:
 		arg->ret = TEEC_ERROR_BAD_PARAMETERS;
@@ -471,7 +473,7 @@
 		break;
 	case OPTEE_RPC_CMD_SHM_ALLOC:
 		free_pages_list(call_ctx);
-		handle_rpc_func_cmd_shm_alloc(ctx, arg, call_ctx);
+		handle_rpc_func_cmd_shm_alloc(ctx, optee, arg, call_ctx);
 		break;
 	case OPTEE_RPC_CMD_SHM_FREE:
 		handle_rpc_func_cmd_shm_free(ctx, arg);
@@ -502,7 +504,7 @@
 
 	switch (OPTEE_SMC_RETURN_GET_RPC_FUNC(param->a0)) {
 	case OPTEE_SMC_RPC_FUNC_ALLOC:
-		shm = tee_shm_alloc(ctx, param->a1,
+		shm = tee_shm_alloc(optee->ctx, param->a1,
 				    TEE_SHM_MAPPED | TEE_SHM_PRIV);
 		if (!IS_ERR(shm) && !tee_shm_get_pa(shm, 0, &pa)) {
 			reg_pair_from_64(&param->a1, &param->a2, pa);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/optee/shm_pool.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/optee/shm_pool.c
@@ -41,10 +41,8 @@
 			goto err;
 		}
 
-		for (i = 0; i < nr_pages; i++) {
-			pages[i] = page;
-			page++;
-		}
+		for (i = 0; i < nr_pages; i++)
+			pages[i] = page + i;
 
 		shm->flags |= TEE_SHM_REGISTER;
 		rc = optee_shm_register(shm->ctx, shm, pages, nr_pages,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/optee/supp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/optee/supp.c
@@ -80,7 +80,6 @@
 	struct optee *optee = tee_get_drvdata(ctx->teedev);
 	struct optee_supp *supp = &optee->supp;
 	struct optee_supp_req *req;
-	bool interruptable;
 	u32 ret;
 
 	/*
@@ -111,36 +110,18 @@
 	/*
 	 * Wait for supplicant to process and return result, once we've
 	 * returned from wait_for_completion(&req->c) successfully we have
-	 * exclusive access again.
+	 * exclusive access again. Allow the wait to be killable such that
+	 * the wait doesn't turn into an indefinite state if the supplicant
+	 * gets hung for some reason.
 	 */
-	while (wait_for_completion_interruptible(&req->c)) {
+	if (wait_for_completion_killable(&req->c)) {
 		mutex_lock(&supp->mutex);
-		interruptable = !supp->ctx;
-		if (interruptable) {
-			/*
-			 * There's no supplicant available and since the
-			 * supp->mutex currently is held none can
-			 * become available until the mutex released
-			 * again.
-			 *
-			 * Interrupting an RPC to supplicant is only
-			 * allowed as a way of slightly improving the user
-			 * experience in case the supplicant hasn't been
-			 * started yet. During normal operation the supplicant
-			 * will serve all requests in a timely manner and
-			 * interrupting then wouldn't make sense.
-			 */
-			if (req->in_queue) {
-				list_del(&req->link);
-				req->in_queue = false;
-			}
+		if (req->in_queue) {
+			list_del(&req->link);
+			req->in_queue = false;
 		}
 		mutex_unlock(&supp->mutex);
-
-		if (interruptable) {
-			req->ret = TEEC_ERROR_COMMUNICATION;
-			break;
-		}
+		req->ret = TEEC_ERROR_COMMUNICATION;
 	}
 
 	ret = req->ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/tee_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/tee_core.c
@@ -43,7 +43,7 @@
 static struct class *tee_class;
 static dev_t tee_devt;
 
-static struct tee_context *teedev_open(struct tee_device *teedev)
+struct tee_context *teedev_open(struct tee_device *teedev)
 {
 	int rc;
 	struct tee_context *ctx;
@@ -70,6 +70,7 @@
 	return ERR_PTR(rc);
 
 }
+EXPORT_SYMBOL_GPL(teedev_open);
 
 void teedev_ctx_get(struct tee_context *ctx)
 {
@@ -96,11 +97,14 @@
 	kref_put(&ctx->refcount, teedev_ctx_release);
 }
 
-static void teedev_close_context(struct tee_context *ctx)
+void teedev_close_context(struct tee_context *ctx)
 {
-	tee_device_put(ctx->teedev);
+	struct tee_device *teedev = ctx->teedev;
+
 	teedev_ctx_put(ctx);
+	tee_device_put(teedev);
 }
+EXPORT_SYMBOL_GPL(teedev_close_context);
 
 static int tee_open(struct inode *inode, struct file *filp)
 {
@@ -330,6 +334,9 @@
 	if (data.flags)
 		return -EINVAL;
 
+	if (!access_ok((void __user *)(unsigned long)data.addr, data.length))
+		return -EFAULT;
+
 	shm = tee_shm_register(ctx, data.addr, data.length,
 			       TEE_SHM_DMA_BUF | TEE_SHM_USER_MAPPED);
 	if (IS_ERR(shm))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tee/tee_shm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tee/tee_shm.c
@@ -1,14 +1,15 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (c) 2015-2016, Linaro Limited
+ * Copyright (c) 2015-2017, 2019-2021 Linaro Limited
  */
+#include <linux/anon_inodes.h>
 #include <linux/device.h>
-#include <linux/dma-buf.h>
-#include <linux/fdtable.h>
 #include <linux/idr.h>
+#include <linux/mm.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/tee_drv.h>
+#include <linux/uaccess.h>
 #include <linux/uio.h>
 #include "tee_private.h"
 
@@ -28,16 +29,8 @@
 	}
 }
 
-static void tee_shm_release(struct tee_shm *shm)
+static void tee_shm_release(struct tee_device *teedev, struct tee_shm *shm)
 {
-	struct tee_device *teedev = shm->ctx->teedev;
-
-	if (shm->flags & TEE_SHM_DMA_BUF) {
-		mutex_lock(&teedev->mutex);
-		idr_remove(&teedev->idr, shm->id);
-		mutex_unlock(&teedev->mutex);
-	}
-
 	if (shm->flags & TEE_SHM_POOL) {
 		struct tee_shm_pool_mgr *poolm;
 
@@ -64,45 +57,6 @@
 	tee_device_put(teedev);
 }
 
-static struct sg_table *tee_shm_op_map_dma_buf(struct dma_buf_attachment
-			*attach, enum dma_data_direction dir)
-{
-	return NULL;
-}
-
-static void tee_shm_op_unmap_dma_buf(struct dma_buf_attachment *attach,
-				     struct sg_table *table,
-				     enum dma_data_direction dir)
-{
-}
-
-static void tee_shm_op_release(struct dma_buf *dmabuf)
-{
-	struct tee_shm *shm = dmabuf->priv;
-
-	tee_shm_release(shm);
-}
-
-static int tee_shm_op_mmap(struct dma_buf *dmabuf, struct vm_area_struct *vma)
-{
-	struct tee_shm *shm = dmabuf->priv;
-	size_t size = vma->vm_end - vma->vm_start;
-
-	/* Refuse sharing shared memory provided by application */
-	if (shm->flags & TEE_SHM_USER_MAPPED)
-		return -EINVAL;
-
-	return remap_pfn_range(vma, vma->vm_start, shm->paddr >> PAGE_SHIFT,
-			       size, vma->vm_page_prot);
-}
-
-static const struct dma_buf_ops tee_shm_dma_buf_ops = {
-	.map_dma_buf = tee_shm_op_map_dma_buf,
-	.unmap_dma_buf = tee_shm_op_unmap_dma_buf,
-	.release = tee_shm_op_release,
-	.mmap = tee_shm_op_mmap,
-};
-
 struct tee_shm *tee_shm_alloc(struct tee_context *ctx, size_t size, u32 flags)
 {
 	struct tee_device *teedev = ctx->teedev;
@@ -137,6 +91,7 @@
 		goto err_dev_put;
 	}
 
+	refcount_set(&shm->refcount, 1);
 	shm->flags = flags | TEE_SHM_POOL;
 	shm->ctx = ctx;
 	if (flags & TEE_SHM_DMA_BUF)
@@ -150,10 +105,7 @@
 		goto err_kfree;
 	}
 
-
 	if (flags & TEE_SHM_DMA_BUF) {
-		DEFINE_DMA_BUF_EXPORT_INFO(exp_info);
-
 		mutex_lock(&teedev->mutex);
 		shm->id = idr_alloc(&teedev->idr, shm, 1, 0, GFP_KERNEL);
 		mutex_unlock(&teedev->mutex);
@@ -161,28 +113,11 @@
 			ret = ERR_PTR(shm->id);
 			goto err_pool_free;
 		}
-
-		exp_info.ops = &tee_shm_dma_buf_ops;
-		exp_info.size = shm->size;
-		exp_info.flags = O_RDWR;
-		exp_info.priv = shm;
-
-		shm->dmabuf = dma_buf_export(&exp_info);
-		if (IS_ERR(shm->dmabuf)) {
-			ret = ERR_CAST(shm->dmabuf);
-			goto err_rem;
-		}
 	}
 
 	teedev_ctx_get(ctx);
 
 	return shm;
-err_rem:
-	if (flags & TEE_SHM_DMA_BUF) {
-		mutex_lock(&teedev->mutex);
-		idr_remove(&teedev->idr, shm->id);
-		mutex_unlock(&teedev->mutex);
-	}
 err_pool_free:
 	poolm->ops->free(poolm, shm);
 err_kfree:
@@ -243,6 +178,7 @@
 		goto err;
 	}
 
+	refcount_set(&shm->refcount, 1);
 	shm->flags = flags | TEE_SHM_REGISTER;
 	shm->ctx = ctx;
 	shm->id = -1;
@@ -303,22 +239,6 @@
 		goto err;
 	}
 
-	if (flags & TEE_SHM_DMA_BUF) {
-		DEFINE_DMA_BUF_EXPORT_INFO(exp_info);
-
-		exp_info.ops = &tee_shm_dma_buf_ops;
-		exp_info.size = shm->size;
-		exp_info.flags = O_RDWR;
-		exp_info.priv = shm;
-
-		shm->dmabuf = dma_buf_export(&exp_info);
-		if (IS_ERR(shm->dmabuf)) {
-			ret = ERR_CAST(shm->dmabuf);
-			teedev->desc->ops->shm_unregister(ctx, shm);
-			goto err;
-		}
-	}
-
 	return shm;
 err:
 	if (shm) {
@@ -336,6 +256,35 @@
 }
 EXPORT_SYMBOL_GPL(tee_shm_register);
 
+static int tee_shm_fop_release(struct inode *inode, struct file *filp)
+{
+	tee_shm_put(filp->private_data);
+	return 0;
+}
+
+static int tee_shm_fop_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+	struct tee_shm *shm = filp->private_data;
+	size_t size = vma->vm_end - vma->vm_start;
+
+	/* Refuse sharing shared memory provided by application */
+	if (shm->flags & TEE_SHM_USER_MAPPED)
+		return -EINVAL;
+
+	/* check for overflowing the buffer's size */
+	if (vma->vm_pgoff + vma_pages(vma) > shm->size >> PAGE_SHIFT)
+		return -EINVAL;
+
+	return remap_pfn_range(vma, vma->vm_start, shm->paddr >> PAGE_SHIFT,
+			       size, vma->vm_page_prot);
+}
+
+static const struct file_operations tee_shm_fops = {
+	.owner = THIS_MODULE,
+	.release = tee_shm_fop_release,
+	.mmap = tee_shm_fop_mmap,
+};
+
 /**
  * tee_shm_get_fd() - Increase reference count and return file descriptor
  * @shm:	Shared memory handle
@@ -348,10 +297,11 @@
 	if (!(shm->flags & TEE_SHM_DMA_BUF))
 		return -EINVAL;
 
-	get_dma_buf(shm->dmabuf);
-	fd = dma_buf_fd(shm->dmabuf, O_CLOEXEC);
+	/* matched by tee_shm_put() in tee_shm_op_release() */
+	refcount_inc(&shm->refcount);
+	fd = anon_inode_getfd("tee_shm", &tee_shm_fops, shm, O_RDWR);
 	if (fd < 0)
-		dma_buf_put(shm->dmabuf);
+		tee_shm_put(shm);
 	return fd;
 }
 
@@ -361,17 +311,7 @@
  */
 void tee_shm_free(struct tee_shm *shm)
 {
-	/*
-	 * dma_buf_put() decreases the dmabuf reference counter and will
-	 * call tee_shm_release() when the last reference is gone.
-	 *
-	 * In the case of driver private memory we call tee_shm_release
-	 * directly instead as it doesn't have a reference counter.
-	 */
-	if (shm->flags & TEE_SHM_DMA_BUF)
-		dma_buf_put(shm->dmabuf);
-	else
-		tee_shm_release(shm);
+	tee_shm_put(shm);
 }
 EXPORT_SYMBOL_GPL(tee_shm_free);
 
@@ -478,10 +418,15 @@
 	teedev = ctx->teedev;
 	mutex_lock(&teedev->mutex);
 	shm = idr_find(&teedev->idr, id);
+	/*
+	 * If the tee_shm was found in the IDR it must have a refcount
+	 * larger than 0 due to the guarantee in tee_shm_put() below. So
+	 * it's safe to use refcount_inc().
+	 */
 	if (!shm || shm->ctx != ctx)
 		shm = ERR_PTR(-EINVAL);
-	else if (shm->flags & TEE_SHM_DMA_BUF)
-		get_dma_buf(shm->dmabuf);
+	else
+		refcount_inc(&shm->refcount);
 	mutex_unlock(&teedev->mutex);
 	return shm;
 }
@@ -493,7 +438,24 @@
  */
 void tee_shm_put(struct tee_shm *shm)
 {
-	if (shm->flags & TEE_SHM_DMA_BUF)
-		dma_buf_put(shm->dmabuf);
+	struct tee_device *teedev = shm->ctx->teedev;
+	bool do_release = false;
+
+	mutex_lock(&teedev->mutex);
+	if (refcount_dec_and_test(&shm->refcount)) {
+		/*
+		 * refcount has reached 0, we must now remove it from the
+		 * IDR before releasing the mutex. This will guarantee that
+		 * the refcount_inc() in tee_shm_get_from_id() never starts
+		 * from 0.
+		 */
+		if (shm->flags & TEE_SHM_DMA_BUF)
+			idr_remove(&teedev->idr, shm->id);
+		do_release = true;
+	}
+	mutex_unlock(&teedev->mutex);
+
+	if (do_release)
+		tee_shm_release(teedev, shm);
 }
 EXPORT_SYMBOL_GPL(tee_shm_put);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/broadcom/bcm2711_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/broadcom/bcm2711_thermal.c
@@ -38,7 +38,6 @@
 	int offset = thermal_zone_get_offset(priv->thermal);
 	u32 val;
 	int ret;
-	long t;
 
 	ret = regmap_read(priv->regmap, AVS_RO_TEMP_STATUS, &val);
 	if (ret)
@@ -50,9 +49,7 @@
 	val &= AVS_RO_TEMP_STATUS_DATA_MSK;
 
 	/* Convert a HW code to a temperature reading (millidegree celsius) */
-	t = slope * val + offset;
-
-	*temp = t < 0 ? 0 : t;
+	*temp = slope * val + offset;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/broadcom/sr-thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/broadcom/sr-thermal.c
@@ -60,6 +60,9 @@
 		return -ENOMEM;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENOENT;
+
 	sr_thermal->regs = (void __iomem *)devm_memremap(&pdev->dev, res->start,
 							 resource_size(res),
 							 MEMREMAP_WB);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/cpufreq_cooling.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/cpufreq_cooling.c
@@ -56,8 +56,6 @@
  * @max_level: maximum cooling level. One less than total number of valid
  *	cpufreq frequencies.
  * @em: Reference on the Energy Model of the device
- * @cdev: thermal_cooling_device pointer to keep track of the
- *	registered cooling device.
  * @policy: cpufreq policy.
  * @idle_time: idle time stats
  * @qos_req: PM QoS contraint to apply
@@ -525,17 +523,17 @@
 	struct thermal_cooling_device_ops *cooling_ops;
 	char *name;
 
+	if (IS_ERR_OR_NULL(policy)) {
+		pr_err("%s: cpufreq policy isn't valid: %p\n", __func__, policy);
+		return ERR_PTR(-EINVAL);
+	}
+
 	dev = get_cpu_device(policy->cpu);
 	if (unlikely(!dev)) {
 		pr_warn("No cpu device for cpu %d\n", policy->cpu);
 		return ERR_PTR(-ENODEV);
 	}
 
-	if (IS_ERR_OR_NULL(policy)) {
-		pr_err("%s: cpufreq policy isn't valid: %p\n", __func__, policy);
-		return ERR_PTR(-EINVAL);
-	}
-
 	i = cpufreq_table_count_valid_entries(policy);
 	if (!i) {
 		pr_debug("%s: CPUFreq table not found or has no valid entries\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/devfreq_cooling.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/devfreq_cooling.c
@@ -199,7 +199,7 @@
 
 		res = dfc->power_ops->get_real_power(df, power, freq, voltage);
 		if (!res) {
-			state = dfc->capped_state;
+			state = dfc->max_state - dfc->capped_state;
 			dfc->res_util = dfc->em_pd->table[state].power;
 			dfc->res_util *= SCALE_ERROR_MITIGATION;
 
@@ -358,21 +358,28 @@
 	struct thermal_cooling_device *cdev;
 	struct device *dev = df->dev.parent;
 	struct devfreq_cooling_device *dfc;
+	struct thermal_cooling_device_ops *ops;
 	char *name;
 	int err, num_opps;
 
-	dfc = kzalloc(sizeof(*dfc), GFP_KERNEL);
-	if (!dfc)
+	ops = kmemdup(&devfreq_cooling_ops, sizeof(*ops), GFP_KERNEL);
+	if (!ops)
 		return ERR_PTR(-ENOMEM);
 
+	dfc = kzalloc(sizeof(*dfc), GFP_KERNEL);
+	if (!dfc) {
+		err = -ENOMEM;
+		goto free_ops;
+	}
+
 	dfc->devfreq = df;
 
 	dfc->em_pd = em_pd_get(dev);
 	if (dfc->em_pd) {
-		devfreq_cooling_ops.get_requested_power =
+		ops->get_requested_power =
 			devfreq_cooling_get_requested_power;
-		devfreq_cooling_ops.state2power = devfreq_cooling_state2power;
-		devfreq_cooling_ops.power2state = devfreq_cooling_power2state;
+		ops->state2power = devfreq_cooling_state2power;
+		ops->power2state = devfreq_cooling_power2state;
 
 		dfc->power_ops = dfc_power;
 
@@ -407,8 +414,7 @@
 	if (!name)
 		goto remove_qos_req;
 
-	cdev = thermal_of_cooling_device_register(np, name, dfc,
-						  &devfreq_cooling_ops);
+	cdev = thermal_of_cooling_device_register(np, name, dfc, ops);
 	kfree(name);
 
 	if (IS_ERR(cdev)) {
@@ -429,6 +435,8 @@
 	kfree(dfc->freq_table);
 free_dfc:
 	kfree(dfc);
+free_ops:
+	kfree(ops);
 
 	return ERR_PTR(err);
 }
@@ -510,11 +518,13 @@
 void devfreq_cooling_unregister(struct thermal_cooling_device *cdev)
 {
 	struct devfreq_cooling_device *dfc;
+	const struct thermal_cooling_device_ops *ops;
 	struct device *dev;
 
 	if (IS_ERR_OR_NULL(cdev))
 		return;
 
+	ops = cdev->ops;
 	dfc = cdev->devdata;
 	dev = dfc->devfreq->dev.parent;
 
@@ -525,5 +535,6 @@
 
 	kfree(dfc->freq_table);
 	kfree(dfc);
+	kfree(ops);
 }
 EXPORT_SYMBOL_GPL(devfreq_cooling_unregister);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/gov_fair_share.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/gov_fair_share.c
@@ -25,10 +25,10 @@
 	int trip_temp;
 	enum thermal_trip_type trip_type;
 
-	if (tz->trips == 0 || !tz->ops->get_trip_temp)
+	if (tz->num_trips == 0 || !tz->ops->get_trip_temp)
 		return 0;
 
-	for (count = 0; count < tz->trips; count++) {
+	for (count = 0; count < tz->num_trips; count++) {
 		tz->ops->get_trip_temp(tz, count, &trip_temp);
 		if (tz->temperature < trip_temp)
 			break;
@@ -49,11 +49,7 @@
 static long get_target_state(struct thermal_zone_device *tz,
 		struct thermal_cooling_device *cdev, int percentage, int level)
 {
-	unsigned long max_state;
-
-	cdev->ops->get_max_state(cdev, &max_state);
-
-	return (long)(percentage * level * max_state) / (100 * tz->trips);
+	return (long)(percentage * level * cdev->max_state) / (100 * tz->num_trips);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/gov_power_allocator.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/gov_power_allocator.c
@@ -527,7 +527,7 @@
 	last_active = INVALID_TRIP;
 	last_passive = INVALID_TRIP;
 
-	for (i = 0; i < tz->trips; i++) {
+	for (i = 0; i < tz->num_trips; i++) {
 		enum thermal_trip_type type;
 		int ret;
 
@@ -668,7 +668,7 @@
 
 	get_governor_trips(tz, params);
 
-	if (tz->trips > 0) {
+	if (tz->num_trips > 0) {
 		ret = tz->ops->get_trip_temp(tz,
 					params->trip_max_desired_temperature,
 					&control_temp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/hisi_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/hisi_thermal.c
@@ -435,10 +435,6 @@
 	data->sensor[0].irq_name = "tsensor_a73";
 	data->sensor[0].data = data;
 
-	data->sensor[1].id = HI3660_LITTLE_SENSOR;
-	data->sensor[1].irq_name = "tsensor_a53";
-	data->sensor[1].data = data;
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/imx8mm_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/imx8mm_thermal.c
@@ -21,6 +21,7 @@
 #define TPS			0x4
 #define TRITSR			0x20	/* TMU immediate temp */
 
+#define TER_ADC_PD		BIT(30)
 #define TER_EN			BIT(31)
 #define TRITSR_TEMP0_VAL_MASK	0xff
 #define TRITSR_TEMP1_VAL_MASK	0xff0000
@@ -64,8 +65,14 @@
 	u32 val;
 
 	val = readl_relaxed(tmu->base + TRITSR) & TRITSR_TEMP0_VAL_MASK;
+
+	/*
+	 * Do not validate against the V bit (bit 31) due to errata
+	 * ERR051272: TMU: Bit 31 of registers TMU_TSCR/TMU_TRITSR/TMU_TRATSR invalid
+	 */
+
 	*temp = val * 1000;
-	if (*temp < VER1_TEMP_LOW_LIMIT)
+	if (*temp < VER1_TEMP_LOW_LIMIT || *temp > VER2_TEMP_HIGH_LIMIT)
 		return -EAGAIN;
 
 	return 0;
@@ -113,6 +120,8 @@
 
 	val = readl_relaxed(tmu->base + TER);
 	val = enable ? (val | TER_EN) : (val & ~TER_EN);
+	if (tmu->socdata->version == TMU_VER2)
+		val = enable ? (val & ~TER_ADC_PD) : (val | TER_ADC_PD);
 	writel_relaxed(val, tmu->base + TER);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/imx_sc_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/imx_sc_thermal.c
@@ -94,8 +94,8 @@
 		sensor = devm_kzalloc(&pdev->dev, sizeof(*sensor), GFP_KERNEL);
 		if (!sensor) {
 			of_node_put(child);
-			of_node_put(sensor_np);
-			return -ENOMEM;
+			ret = -ENOMEM;
+			goto put_node;
 		}
 
 		ret = thermal_zone_of_get_sensor_id(child,
@@ -124,7 +124,9 @@
 			dev_warn(&pdev->dev, "failed to add hwmon sysfs attributes\n");
 	}
 
+put_node:
 	of_node_put(sensor_np);
+	of_node_put(np);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/imx_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/imx_thermal.c
@@ -15,6 +15,7 @@
 #include <linux/regmap.h>
 #include <linux/thermal.h>
 #include <linux/nvmem-consumer.h>
+#include <linux/pm_runtime.h>
 
 #define REG_SET		0x4
 #define REG_CLR		0x8
@@ -194,6 +195,7 @@
 };
 
 struct imx_thermal_data {
+	struct device *dev;
 	struct cpufreq_policy *policy;
 	struct thermal_zone_device *tz;
 	struct thermal_cooling_device *cdev;
@@ -252,44 +254,15 @@
 	const struct thermal_soc_data *soc_data = data->socdata;
 	struct regmap *map = data->tempmon;
 	unsigned int n_meas;
-	bool wait, run_measurement;
 	u32 val;
+	int ret;
 
-	run_measurement = !data->irq_enabled;
-	if (!run_measurement) {
-		/* Check if a measurement is currently in progress */
-		regmap_read(map, soc_data->temp_data, &val);
-		wait = !(val & soc_data->temp_valid_mask);
-	} else {
-		/*
-		 * Every time we measure the temperature, we will power on the
-		 * temperature sensor, enable measurements, take a reading,
-		 * disable measurements, power off the temperature sensor.
-		 */
-		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
-			    soc_data->power_down_mask);
-		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
-			    soc_data->measure_temp_mask);
-
-		wait = true;
-	}
-
-	/*
-	 * According to the temp sensor designers, it may require up to ~17us
-	 * to complete a measurement.
-	 */
-	if (wait)
-		usleep_range(20, 50);
+	ret = pm_runtime_resume_and_get(data->dev);
+	if (ret < 0)
+		return ret;
 
 	regmap_read(map, soc_data->temp_data, &val);
 
-	if (run_measurement) {
-		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
-			     soc_data->measure_temp_mask);
-		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
-			     soc_data->power_down_mask);
-	}
-
 	if ((val & soc_data->temp_valid_mask) == 0) {
 		dev_dbg(&tz->device, "temp measurement never finished\n");
 		return -EAGAIN;
@@ -328,6 +301,8 @@
 		enable_irq(data->irq);
 	}
 
+	pm_runtime_put(data->dev);
+
 	return 0;
 }
 
@@ -335,24 +310,16 @@
 			   enum thermal_device_mode mode)
 {
 	struct imx_thermal_data *data = tz->devdata;
-	struct regmap *map = data->tempmon;
-	const struct thermal_soc_data *soc_data = data->socdata;
 
 	if (mode == THERMAL_DEVICE_ENABLED) {
-		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
-			     soc_data->power_down_mask);
-		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
-			     soc_data->measure_temp_mask);
+		pm_runtime_get(data->dev);
 
 		if (!data->irq_enabled) {
 			data->irq_enabled = true;
 			enable_irq(data->irq);
 		}
 	} else {
-		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
-			     soc_data->measure_temp_mask);
-		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
-			     soc_data->power_down_mask);
+		pm_runtime_put(data->dev);
 
 		if (data->irq_enabled) {
 			disable_irq(data->irq);
@@ -393,6 +360,11 @@
 			     int temp)
 {
 	struct imx_thermal_data *data = tz->devdata;
+	int ret;
+
+	ret = pm_runtime_resume_and_get(data->dev);
+	if (ret < 0)
+		return ret;
 
 	/* do not allow changing critical threshold */
 	if (trip == IMX_TRIP_CRITICAL)
@@ -406,6 +378,8 @@
 
 	imx_set_alarm_temp(data, temp);
 
+	pm_runtime_put(data->dev);
+
 	return 0;
 }
 
@@ -681,6 +655,8 @@
 	if (!data)
 		return -ENOMEM;
 
+	data->dev = &pdev->dev;
+
 	map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "fsl,tempmon");
 	if (IS_ERR(map)) {
 		ret = PTR_ERR(map);
@@ -800,6 +776,16 @@
 		     data->socdata->power_down_mask);
 	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
 		     data->socdata->measure_temp_mask);
+	/* After power up, we need a delay before first access can be done. */
+	usleep_range(20, 50);
+
+	/* the core was configured and enabled just before */
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(data->dev);
+
+	ret = pm_runtime_resume_and_get(data->dev);
+	if (ret < 0)
+		goto disable_runtime_pm;
 
 	data->irq_enabled = true;
 	ret = thermal_zone_device_enable(data->tz);
@@ -814,10 +800,15 @@
 		goto thermal_zone_unregister;
 	}
 
+	pm_runtime_put(data->dev);
+
 	return 0;
 
 thermal_zone_unregister:
 	thermal_zone_device_unregister(data->tz);
+disable_runtime_pm:
+	pm_runtime_put_noidle(data->dev);
+	pm_runtime_disable(data->dev);
 clk_disable:
 	clk_disable_unprepare(data->thermal_clk);
 legacy_cleanup:
@@ -829,13 +820,9 @@
 static int imx_thermal_remove(struct platform_device *pdev)
 {
 	struct imx_thermal_data *data = platform_get_drvdata(pdev);
-	struct regmap *map = data->tempmon;
 
-	/* Disable measurements */
-	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
-		     data->socdata->power_down_mask);
-	if (!IS_ERR(data->thermal_clk))
-		clk_disable_unprepare(data->thermal_clk);
+	pm_runtime_put_noidle(data->dev);
+	pm_runtime_disable(data->dev);
 
 	thermal_zone_device_unregister(data->tz);
 	imx_thermal_unregister_legacy_cooling(data);
@@ -858,29 +845,79 @@
 	ret = thermal_zone_device_disable(data->tz);
 	if (ret)
 		return ret;
+
+	return pm_runtime_force_suspend(data->dev);
+}
+
+static int __maybe_unused imx_thermal_resume(struct device *dev)
+{
+	struct imx_thermal_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = pm_runtime_force_resume(data->dev);
+	if (ret)
+		return ret;
+	/* Enabled thermal sensor after resume */
+	return thermal_zone_device_enable(data->tz);
+}
+
+static int __maybe_unused imx_thermal_runtime_suspend(struct device *dev)
+{
+	struct imx_thermal_data *data = dev_get_drvdata(dev);
+	const struct thermal_soc_data *socdata = data->socdata;
+	struct regmap *map = data->tempmon;
+	int ret;
+
+	ret = regmap_write(map, socdata->sensor_ctrl + REG_CLR,
+			   socdata->measure_temp_mask);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(map, socdata->sensor_ctrl + REG_SET,
+			   socdata->power_down_mask);
+	if (ret)
+		return ret;
+
 	clk_disable_unprepare(data->thermal_clk);
 
 	return 0;
 }
 
-static int __maybe_unused imx_thermal_resume(struct device *dev)
+static int __maybe_unused imx_thermal_runtime_resume(struct device *dev)
 {
 	struct imx_thermal_data *data = dev_get_drvdata(dev);
+	const struct thermal_soc_data *socdata = data->socdata;
+	struct regmap *map = data->tempmon;
 	int ret;
 
 	ret = clk_prepare_enable(data->thermal_clk);
 	if (ret)
 		return ret;
-	/* Enabled thermal sensor after resume */
-	ret = thermal_zone_device_enable(data->tz);
+
+	ret = regmap_write(map, socdata->sensor_ctrl + REG_CLR,
+			   socdata->power_down_mask);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(map, socdata->sensor_ctrl + REG_SET,
+			   socdata->measure_temp_mask);
 	if (ret)
 		return ret;
 
+	/*
+	 * According to the temp sensor designers, it may require up to ~17us
+	 * to complete a measurement.
+	 */
+	usleep_range(20, 50);
+
 	return 0;
 }
 
-static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops,
-			 imx_thermal_suspend, imx_thermal_resume);
+static const struct dev_pm_ops imx_thermal_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(imx_thermal_suspend, imx_thermal_resume)
+	SET_RUNTIME_PM_OPS(imx_thermal_runtime_suspend,
+			   imx_thermal_runtime_resume, NULL)
+};
 
 static struct platform_driver imx_thermal = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/Kconfig
@@ -64,7 +64,8 @@
 
 config INTEL_BXT_PMIC_THERMAL
 	tristate "Intel Broxton PMIC thermal driver"
-	depends on X86 && INTEL_SOC_PMIC_BXTWC && REGMAP
+	depends on X86 && INTEL_SOC_PMIC_BXTWC
+	select REGMAP
 	help
 	  Select this driver for Intel Broxton PMIC with ADC channels monitoring
 	  system temperature measurements and alerts.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/Kconfig
@@ -5,12 +5,12 @@
 
 config INT340X_THERMAL
 	tristate "ACPI INT340X thermal drivers"
-	depends on X86 && ACPI && PCI
+	depends on X86_64 && ACPI && PCI
 	select THERMAL_GOV_USER_SPACE
 	select ACPI_THERMAL_REL
 	select ACPI_FAN
 	select INTEL_SOC_DTS_IOSF_CORE
-	select PROC_THERMAL_MMIO_RAPL if X86_64 && POWERCAP
+	select PROC_THERMAL_MMIO_RAPL if POWERCAP
 	help
 	  Newer laptops and tablets that use ACPI may have thermal sensors and
 	  other devices with thermal control capabilities outside the core
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/int3400_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/int3400_thermal.c
@@ -17,8 +17,8 @@
 #define INT3400_KEEP_ALIVE 0xA0
 
 enum int3400_thermal_uuid {
+	INT3400_THERMAL_ACTIVE = 0,
 	INT3400_THERMAL_PASSIVE_1,
-	INT3400_THERMAL_ACTIVE,
 	INT3400_THERMAL_CRITICAL,
 	INT3400_THERMAL_ADAPTIVE_PERFORMANCE,
 	INT3400_THERMAL_EMERGENCY_CALL_MODE,
@@ -31,8 +31,8 @@
 };
 
 static char *int3400_thermal_uuids[INT3400_THERMAL_MAXIMUM_UUID] = {
-	"42A441D6-AE6A-462b-A84B-4A8CE79027D3",
 	"3A95C389-E4B8-4629-A526-C52C88626BAE",
+	"42A441D6-AE6A-462b-A84B-4A8CE79027D3",
 	"97C68AE7-15FA-499c-B8C9-5DA81D606E0A",
 	"63BE270F-1C11-48FD-A6F7-3AF253FF3E2D",
 	"5349962F-71E6-431D-9AE8-0A635B710AEE",
@@ -53,12 +53,13 @@
 	struct art *arts;
 	int trt_count;
 	struct trt *trts;
-	u8 uuid_bitmap;
+	u32 uuid_bitmap;
 	int rel_misc_dev_res;
 	int current_uuid_index;
 	char *data_vault;
 	int odvp_count;
 	int *odvp;
+	u32 os_uuid_mask;
 	struct odvp_attr *odvp_attrs;
 };
 
@@ -67,7 +68,7 @@
 struct odvp_attr {
 	int odvp;
 	struct int3400_thermal_priv *priv;
-	struct kobj_attribute attr;
+	struct device_attribute attr;
 };
 
 static ssize_t data_vault_read(struct file *file, struct kobject *kobj,
@@ -143,12 +144,55 @@
 				 struct device_attribute *devattr, char *buf)
 {
 	struct int3400_thermal_priv *priv = dev_get_drvdata(dev);
+	int i, length = 0;
+
+	if (priv->current_uuid_index > 0)
+		return sprintf(buf, "%s\n",
+			       int3400_thermal_uuids[priv->current_uuid_index]);
+
+	for (i = 0; i <= INT3400_THERMAL_CRITICAL; i++) {
+		if (priv->os_uuid_mask & BIT(i))
+			length += scnprintf(&buf[length],
+					    PAGE_SIZE - length,
+					    "%s\n",
+					    int3400_thermal_uuids[i]);
+	}
 
-	if (priv->current_uuid_index == -1)
-		return sprintf(buf, "INVALID\n");
+	if (length)
+		return length;
 
-	return sprintf(buf, "%s\n",
-		       int3400_thermal_uuids[priv->current_uuid_index]);
+	return sprintf(buf, "INVALID\n");
+}
+
+static int int3400_thermal_run_osc(acpi_handle handle, char *uuid_str, int *enable)
+{
+	u32 ret, buf[2];
+	acpi_status status;
+	int result = 0;
+	struct acpi_osc_context context = {
+		.uuid_str = NULL,
+		.rev = 1,
+		.cap.length = 8,
+	};
+
+	context.uuid_str = uuid_str;
+
+	buf[OSC_QUERY_DWORD] = 0;
+	buf[OSC_SUPPORT_DWORD] = *enable;
+
+	context.cap.pointer = buf;
+
+	status = acpi_run_osc(handle, &context);
+	if (ACPI_SUCCESS(status)) {
+		ret = *((u32 *)(context.ret.pointer + 4));
+		if (ret != *enable)
+			result = -EPERM;
+	} else
+		result = -EPERM;
+
+	kfree(context.ret.pointer);
+
+	return result;
 }
 
 static ssize_t current_uuid_store(struct device *dev,
@@ -165,16 +209,47 @@
 			 * If we have a list of supported UUIDs, make sure
 			 * this one is supported.
 			 */
-			if (priv->uuid_bitmap &&
-			    !(priv->uuid_bitmap & (1 << i)))
+			if (priv->uuid_bitmap & BIT(i)) {
+				priv->current_uuid_index = i;
+				return count;
+			}
+
+			/*
+			 * There is support of only 3 policies via the new
+			 * _OSC to inform OS capability:
+			 * INT3400_THERMAL_ACTIVE
+			 * INT3400_THERMAL_PASSIVE_1
+			 * INT3400_THERMAL_CRITICAL
+			 */
+
+			if (i > INT3400_THERMAL_CRITICAL)
 				return -EINVAL;
 
-			priv->current_uuid_index = i;
-			return count;
+			priv->os_uuid_mask |= BIT(i);
+
+			break;
 		}
 	}
 
-	return -EINVAL;
+	if (priv->os_uuid_mask) {
+		int cap, ret;
+
+		/*
+		 * Capability bits:
+		 * Bit 0: set to 1 to indicate DPTF is active
+		 * Bi1 1: set to 1 to active cooling is supported by user space daemon
+		 * Bit 2: set to 1 to passive cooling is supported by user space daemon
+		 * Bit 3: set to 1 to critical trip is handled by user space daemon
+		 */
+		cap = ((priv->os_uuid_mask << 1) | 0x01);
+		ret = int3400_thermal_run_osc(priv->adev->handle,
+					      "b23ba85d-c8b7-3542-88de-8de2ffcfd698",
+					      &cap);
+		if (ret)
+			return ret;
+	}
+
+	return count;
 }
 
 static DEVICE_ATTR_RW(current_uuid);
@@ -237,42 +312,7 @@
 	return result;
 }
 
-static int int3400_thermal_run_osc(acpi_handle handle,
-				enum int3400_thermal_uuid uuid, bool enable)
-{
-	u32 ret, buf[2];
-	acpi_status status;
-	int result = 0;
-	struct acpi_osc_context context = {
-		.uuid_str = NULL,
-		.rev = 1,
-		.cap.length = 8,
-	};
-
-	if (uuid < 0 || uuid >= INT3400_THERMAL_MAXIMUM_UUID)
-		return -EINVAL;
-
-	context.uuid_str = int3400_thermal_uuids[uuid];
-
-	buf[OSC_QUERY_DWORD] = 0;
-	buf[OSC_SUPPORT_DWORD] = enable;
-
-	context.cap.pointer = buf;
-
-	status = acpi_run_osc(handle, &context);
-	if (ACPI_SUCCESS(status)) {
-		ret = *((u32 *)(context.ret.pointer + 4));
-		if (ret != enable)
-			result = -EPERM;
-	} else
-		result = -EPERM;
-
-	kfree(context.ret.pointer);
-
-	return result;
-}
-
-static ssize_t odvp_show(struct kobject *kobj, struct kobj_attribute *attr,
+static ssize_t odvp_show(struct device *dev, struct device_attribute *attr,
 			 char *buf)
 {
 	struct odvp_attr *odvp_attr;
@@ -405,6 +445,10 @@
 	thermal_prop[3] = kasprintf(GFP_KERNEL, "EVENT=%d", therm_event);
 	thermal_prop[4] = NULL;
 	kobject_uevent_env(&priv->thermal->device.kobj, KOBJ_CHANGE, thermal_prop);
+	kfree(thermal_prop[0]);
+	kfree(thermal_prop[1]);
+	kfree(thermal_prop[2]);
+	kfree(thermal_prop[3]);
 }
 
 static int int3400_thermal_get_temp(struct thermal_zone_device *thermal,
@@ -423,10 +467,18 @@
 	if (!priv)
 		return -EINVAL;
 
-	if (mode != thermal->mode)
+	if (mode != thermal->mode) {
+		int enabled;
+
+		if (priv->current_uuid_index < 0 ||
+		    priv->current_uuid_index >= INT3400_THERMAL_MAXIMUM_UUID)
+			return -EINVAL;
+
+		enabled = (mode == THERMAL_DEVICE_ENABLED);
 		result = int3400_thermal_run_osc(priv->adev->handle,
-						priv->current_uuid_index,
-						mode == THERMAL_DEVICE_ENABLED);
+						 int3400_thermal_uuids[priv->current_uuid_index],
+						 &enabled);
+	}
 
 
 	evaluate_odvp(priv);
@@ -465,6 +517,11 @@
 	priv->data_vault = kmemdup(obj->package.elements[0].buffer.pointer,
 				   obj->package.elements[0].buffer.length,
 				   GFP_KERNEL);
+	if (!priv->data_vault) {
+		kfree(buffer.pointer);
+		return;
+	}
+
 	bin_attr_data_vault.private = priv->data_vault;
 	bin_attr_data_vault.size = obj->package.elements[0].buffer.length;
 	kfree(buffer.pointer);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/int3401_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/int3401_thermal.c
@@ -44,15 +44,21 @@
 }
 
 #ifdef CONFIG_PM_SLEEP
+static int int3401_thermal_suspend(struct device *dev)
+{
+	return proc_thermal_suspend(dev);
+}
 static int int3401_thermal_resume(struct device *dev)
 {
 	return proc_thermal_resume(dev);
 }
 #else
+#define int3401_thermal_suspend NULL
 #define int3401_thermal_resume NULL
 #endif
 
-static SIMPLE_DEV_PM_OPS(int3401_proc_thermal_pm, NULL, int3401_thermal_resume);
+static SIMPLE_DEV_PM_OPS(int3401_proc_thermal_pm, int3401_thermal_suspend,
+			 int3401_thermal_resume);
 
 static struct platform_driver int3401_driver = {
 	.probe = int3401_add,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/int3402_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/int3402_thermal.c
@@ -45,6 +45,9 @@
 	struct int3402_thermal_data *d;
 	int ret;
 
+	if (!adev)
+		return -ENODEV;
+
 	if (!acpi_has_method(adev->handle, "_TMP"))
 		return -ENODEV;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.c
@@ -44,11 +44,13 @@
 					 int trip, int *temp)
 {
 	struct int34x_thermal_zone *d = zone->devdata;
-	int i;
+	int i, ret = 0;
 
 	if (d->override_ops && d->override_ops->get_trip_temp)
 		return d->override_ops->get_trip_temp(zone, trip, temp);
 
+	mutex_lock(&d->trip_mutex);
+
 	if (trip < d->aux_trip_nr)
 		*temp = d->aux_trips[trip];
 	else if (trip == d->crt_trip_id)
@@ -66,10 +68,12 @@
 			}
 		}
 		if (i == INT340X_THERMAL_MAX_ACT_TRIP_COUNT)
-			return -EINVAL;
+			ret = -EINVAL;
 	}
 
-	return 0;
+	mutex_unlock(&d->trip_mutex);
+
+	return ret;
 }
 
 static int int340x_thermal_get_trip_type(struct thermal_zone_device *zone,
@@ -77,11 +81,13 @@
 					 enum thermal_trip_type *type)
 {
 	struct int34x_thermal_zone *d = zone->devdata;
-	int i;
+	int i, ret = 0;
 
 	if (d->override_ops && d->override_ops->get_trip_type)
 		return d->override_ops->get_trip_type(zone, trip, type);
 
+	mutex_lock(&d->trip_mutex);
+
 	if (trip < d->aux_trip_nr)
 		*type = THERMAL_TRIP_PASSIVE;
 	else if (trip == d->crt_trip_id)
@@ -99,10 +105,12 @@
 			}
 		}
 		if (i == INT340X_THERMAL_MAX_ACT_TRIP_COUNT)
-			return -EINVAL;
+			ret = -EINVAL;
 	}
 
-	return 0;
+	mutex_unlock(&d->trip_mutex);
+
+	return ret;
 }
 
 static int int340x_thermal_set_trip_temp(struct thermal_zone_device *zone,
@@ -180,6 +188,8 @@
 	int trip_cnt = int34x_zone->aux_trip_nr;
 	int i;
 
+	mutex_lock(&int34x_zone->trip_mutex);
+
 	int34x_zone->crt_trip_id = -1;
 	if (!int340x_thermal_get_trip_config(int34x_zone->adev->handle, "_CRT",
 					     &int34x_zone->crt_temp))
@@ -207,6 +217,8 @@
 		int34x_zone->act_trips[i].valid = true;
 	}
 
+	mutex_unlock(&int34x_zone->trip_mutex);
+
 	return trip_cnt;
 }
 EXPORT_SYMBOL_GPL(int340x_thermal_read_trips);
@@ -230,6 +242,8 @@
 	if (!int34x_thermal_zone)
 		return ERR_PTR(-ENOMEM);
 
+	mutex_init(&int34x_thermal_zone->trip_mutex);
+
 	int34x_thermal_zone->adev = adev;
 	int34x_thermal_zone->override_ops = override_ops;
 
@@ -281,6 +295,7 @@
 	acpi_lpat_free_conversion_table(int34x_thermal_zone->lpat_table);
 	kfree(int34x_thermal_zone->aux_trips);
 err_trip_alloc:
+	mutex_destroy(&int34x_thermal_zone->trip_mutex);
 	kfree(int34x_thermal_zone);
 	return ERR_PTR(ret);
 }
@@ -292,6 +307,7 @@
 	thermal_zone_device_unregister(int34x_thermal_zone->zone);
 	acpi_lpat_free_conversion_table(int34x_thermal_zone->lpat_table);
 	kfree(int34x_thermal_zone->aux_trips);
+	mutex_destroy(&int34x_thermal_zone->trip_mutex);
 	kfree(int34x_thermal_zone);
 }
 EXPORT_SYMBOL_GPL(int340x_thermal_zone_remove);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.h
@@ -32,6 +32,7 @@
 	struct thermal_zone_device_ops *override_ops;
 	void *priv_data;
 	struct acpi_lpat_conversion_table *lpat_table;
+	struct mutex trip_mutex;
 };
 
 struct int34x_thermal_zone *int340x_thermal_zone_add(struct acpi_device *,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
@@ -68,8 +68,7 @@
 	.name = "power_limits"
 };
 
-static ssize_t tcc_offset_degree_celsius_show(struct device *dev,
-			       struct device_attribute *attr, char *buf)
+static int tcc_get_offset(void)
 {
 	u64 val;
 	int err;
@@ -78,8 +77,20 @@
 	if (err)
 		return err;
 
-	val = (val >> 24) & 0x3f;
-	return sprintf(buf, "%d\n", (int)val);
+	return (val >> 24) & 0x3f;
+}
+
+static ssize_t tcc_offset_degree_celsius_show(struct device *dev,
+					      struct device_attribute *attr,
+					      char *buf)
+{
+	int tcc;
+
+	tcc = tcc_get_offset();
+	if (tcc < 0)
+		return tcc;
+
+	return sprintf(buf, "%d\n", tcc);
 }
 
 static int tcc_offset_update(unsigned int tcc)
@@ -107,8 +118,6 @@
 	return 0;
 }
 
-static int tcc_offset_save = -1;
-
 static ssize_t tcc_offset_degree_celsius_store(struct device *dev,
 				struct device_attribute *attr, const char *buf,
 				size_t count)
@@ -131,8 +140,6 @@
 	if (err)
 		return err;
 
-	tcc_offset_save = tcc;
-
 	return count;
 }
 
@@ -345,6 +352,18 @@
 }
 EXPORT_SYMBOL_GPL(proc_thermal_remove);
 
+static int tcc_offset_save = -1;
+
+int proc_thermal_suspend(struct device *dev)
+{
+	tcc_offset_save = tcc_get_offset();
+	if (tcc_offset_save < 0)
+		dev_warn(dev, "failed to save offset (%d)\n", tcc_offset_save);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(proc_thermal_suspend);
+
 int proc_thermal_resume(struct device *dev)
 {
 	struct proc_thermal_device *proc_dev;
@@ -352,6 +371,7 @@
 	proc_dev = dev_get_drvdata(dev);
 	proc_thermal_read_ppcc(proc_dev);
 
+	/* Do not update if saving failed */
 	if (tcc_offset_save >= 0)
 		tcc_offset_update(tcc_offset_save);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
@@ -80,9 +80,11 @@
 int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv);
 void proc_thermal_mbox_remove(struct pci_dev *pdev);
 
-int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp);
+int processor_thermal_send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp);
+int processor_thermal_send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data);
 int proc_thermal_add(struct device *dev, struct proc_thermal_device *priv);
 void proc_thermal_remove(struct proc_thermal_device *proc_priv);
+int proc_thermal_suspend(struct device *dev);
 int proc_thermal_resume(struct device *dev);
 int proc_thermal_mmio_add(struct pci_dev *pdev,
 			  struct proc_thermal_device *proc_priv,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c
@@ -237,26 +237,26 @@
 
 	INIT_DELAYED_WORK(&pci_info->work, proc_thermal_threshold_work_fn);
 
-	ret = proc_thermal_add(&pdev->dev, proc_priv);
-	if (ret) {
-		dev_err(&pdev->dev, "error: proc_thermal_add, will continue\n");
-		pci_info->no_legacy = 1;
-	}
-
 	proc_priv->priv_data = pci_info;
 	pci_info->proc_priv = proc_priv;
 	pci_set_drvdata(pdev, proc_priv);
 
 	ret = proc_thermal_mmio_add(pdev, proc_priv, id->driver_data);
 	if (ret)
-		goto err_ret_thermal;
+		return ret;
+
+	ret = proc_thermal_add(&pdev->dev, proc_priv);
+	if (ret) {
+		dev_err(&pdev->dev, "error: proc_thermal_add, will continue\n");
+		pci_info->no_legacy = 1;
+	}
 
 	pci_info->tzone = thermal_zone_device_register("TCPU_PCI", 1, 1, pci_info,
 							&tzone_ops,
 							&tzone_params, 0, 0);
 	if (IS_ERR(pci_info->tzone)) {
 		ret = PTR_ERR(pci_info->tzone);
-		goto err_ret_mmio;
+		goto err_del_legacy;
 	}
 
 	/* request and enable interrupt */
@@ -283,12 +283,10 @@
 	pci_free_irq_vectors(pdev);
 err_ret_tzone:
 	thermal_zone_device_unregister(pci_info->tzone);
-err_ret_mmio:
-	proc_thermal_mmio_remove(pdev, proc_priv);
-err_ret_thermal:
+err_del_legacy:
 	if (!pci_info->no_legacy)
 		proc_thermal_remove(proc_priv);
-	pci_disable_device(pdev);
+	proc_thermal_mmio_remove(pdev, proc_priv);
 
 	return ret;
 }
@@ -310,10 +308,23 @@
 	proc_thermal_mmio_remove(pdev, pci_info->proc_priv);
 	if (!pci_info->no_legacy)
 		proc_thermal_remove(proc_priv);
-	pci_disable_device(pdev);
 }
 
 #ifdef CONFIG_PM_SLEEP
+static int proc_thermal_pci_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct proc_thermal_device *proc_priv;
+	struct proc_thermal_pci *pci_info;
+
+	proc_priv = pci_get_drvdata(pdev);
+	pci_info = proc_priv->priv_data;
+
+	if (!pci_info->no_legacy)
+		return proc_thermal_suspend(dev);
+
+	return 0;
+}
 static int proc_thermal_pci_resume(struct device *dev)
 {
 	struct pci_dev *pdev = to_pci_dev(dev);
@@ -335,10 +346,12 @@
 	return 0;
 }
 #else
+#define proc_thermal_pci_suspend NULL
 #define proc_thermal_pci_resume NULL
 #endif
 
-static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, NULL, proc_thermal_pci_resume);
+static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, proc_thermal_pci_suspend,
+			 proc_thermal_pci_resume);
 
 static const struct pci_device_id proc_thermal_pci_ids[] = {
 	{ PCI_DEVICE_DATA(INTEL, ADL_THERMAL, PROC_THERMAL_FEATURE_RAPL | PROC_THERMAL_FEATURE_FIVR | PROC_THERMAL_FEATURE_DVFS | PROC_THERMAL_FEATURE_MBOX) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci_legacy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci_legacy.c
@@ -107,15 +107,21 @@
 }
 
 #ifdef CONFIG_PM_SLEEP
+static int proc_thermal_pci_suspend(struct device *dev)
+{
+	return proc_thermal_suspend(dev);
+}
 static int proc_thermal_pci_resume(struct device *dev)
 {
 	return proc_thermal_resume(dev);
 }
 #else
+#define proc_thermal_pci_suspend NULL
 #define proc_thermal_pci_resume NULL
 #endif
 
-static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, NULL, proc_thermal_pci_resume);
+static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, proc_thermal_pci_suspend,
+			 proc_thermal_pci_resume);
 
 static const struct pci_device_id proc_thermal_pci_ids[] = {
 	{ PCI_DEVICE_DATA(INTEL, BDW_THERMAL, 0) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c
@@ -7,6 +7,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
 #include "processor_thermal_device.h"
 
 #define MBOX_CMD_WORKLOAD_TYPE_READ	0x0E
@@ -23,19 +24,15 @@
 
 static DEFINE_MUTEX(mbox_lock);
 
-static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp)
+static int wait_for_mbox_ready(struct proc_thermal_device *proc_priv)
 {
-	struct proc_thermal_device *proc_priv;
 	u32 retries, data;
 	int ret;
 
-	mutex_lock(&mbox_lock);
-	proc_priv = pci_get_drvdata(pdev);
-
 	/* Poll for rb bit == 0 */
 	retries = MBOX_RETRY_COUNT;
 	do {
-		data = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE));
+		data = readl(proc_priv->mmio_base + MBOX_OFFSET_INTERFACE);
 		if (data & BIT_ULL(MBOX_BUSY_BIT)) {
 			ret = -EBUSY;
 			continue;
@@ -44,49 +41,78 @@
 		break;
 	} while (--retries);
 
+	return ret;
+}
+
+static int send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data)
+{
+	struct proc_thermal_device *proc_priv;
+	u32 reg_data;
+	int ret;
+
+	proc_priv = pci_get_drvdata(pdev);
+
+	mutex_lock(&mbox_lock);
+
+	ret = wait_for_mbox_ready(proc_priv);
 	if (ret)
 		goto unlock_mbox;
 
-	if (cmd_id == MBOX_CMD_WORKLOAD_TYPE_WRITE)
-		writel(cmd_data, (void __iomem *) ((proc_priv->mmio_base + MBOX_OFFSET_DATA)));
-
+	writel(data, (proc_priv->mmio_base + MBOX_OFFSET_DATA));
 	/* Write command register */
-	data = BIT_ULL(MBOX_BUSY_BIT) | cmd_id;
-	writel(data, (void __iomem *) ((proc_priv->mmio_base + MBOX_OFFSET_INTERFACE)));
+	reg_data = BIT_ULL(MBOX_BUSY_BIT) | id;
+	writel(reg_data, (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE));
 
-	/* Poll for rb bit == 0 */
-	retries = MBOX_RETRY_COUNT;
-	do {
-		data = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE));
-		if (data & BIT_ULL(MBOX_BUSY_BIT)) {
-			ret = -EBUSY;
-			continue;
-		}
+	ret = wait_for_mbox_ready(proc_priv);
 
-		if (data) {
-			ret = -ENXIO;
-			goto unlock_mbox;
-		}
+unlock_mbox:
+	mutex_unlock(&mbox_lock);
+	return ret;
+}
 
-		if (cmd_id == MBOX_CMD_WORKLOAD_TYPE_READ) {
-			data = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA));
-			*cmd_resp = data & 0xff;
-		}
+static int send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp)
+{
+	struct proc_thermal_device *proc_priv;
+	u32 reg_data;
+	int ret;
 
-		ret = 0;
-		break;
-	} while (--retries);
+	proc_priv = pci_get_drvdata(pdev);
+
+	mutex_lock(&mbox_lock);
+
+	ret = wait_for_mbox_ready(proc_priv);
+	if (ret)
+		goto unlock_mbox;
+
+	/* Write command register */
+	reg_data = BIT_ULL(MBOX_BUSY_BIT) | id;
+	writel(reg_data, (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE));
+
+	ret = wait_for_mbox_ready(proc_priv);
+	if (ret)
+		goto unlock_mbox;
+
+	if (id == MBOX_CMD_WORKLOAD_TYPE_READ)
+		*resp = readl(proc_priv->mmio_base + MBOX_OFFSET_DATA);
+	else
+		*resp = readq(proc_priv->mmio_base + MBOX_OFFSET_DATA);
 
 unlock_mbox:
 	mutex_unlock(&mbox_lock);
 	return ret;
 }
 
-int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp)
+int processor_thermal_send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp)
 {
-	return send_mbox_cmd(pdev, cmd_id, cmd_data, cmd_resp);
+	return send_mbox_read_cmd(pdev, id, resp);
 }
-EXPORT_SYMBOL_GPL(processor_thermal_send_mbox_cmd);
+EXPORT_SYMBOL_NS_GPL(processor_thermal_send_mbox_read_cmd, INT340X_THERMAL);
+
+int processor_thermal_send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data)
+{
+	return send_mbox_write_cmd(pdev, id, data);
+}
+EXPORT_SYMBOL_NS_GPL(processor_thermal_send_mbox_write_cmd, INT340X_THERMAL);
 
 /* List of workload types */
 static const char * const workload_types[] = {
@@ -99,7 +125,6 @@
 	NULL
 };
 
-
 static ssize_t workload_available_types_show(struct device *dev,
 					       struct device_attribute *attr,
 					       char *buf)
@@ -141,7 +166,7 @@
 
 	data |= ret;
 
-	ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_WRITE, data, NULL);
+	ret = send_mbox_write_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_WRITE, data);
 	if (ret)
 		return false;
 
@@ -153,10 +178,10 @@
 				   char *buf)
 {
 	struct pci_dev *pdev = to_pci_dev(dev);
-	u32 cmd_resp;
+	u64 cmd_resp;
 	int ret;
 
-	ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, 0, &cmd_resp);
+	ret = send_mbox_read_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, &cmd_resp);
 	if (ret)
 		return false;
 
@@ -181,17 +206,15 @@
 	.name = "workload_request"
 };
 
-
-
 static bool workload_req_created;
 
 int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv)
 {
-	u32 cmd_resp;
+	u64 cmd_resp;
 	int ret;
 
 	/* Check if there is a mailbox support, if fails return success */
-	ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, 0, &cmd_resp);
+	ret = send_mbox_read_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, &cmd_resp);
 	if (ret)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c
@@ -9,6 +9,8 @@
 #include <linux/pci.h>
 #include "processor_thermal_device.h"
 
+MODULE_IMPORT_NS(INT340X_THERMAL);
+
 struct mmio_reg {
 	int read_only;
 	u32 offset;
@@ -29,7 +31,7 @@
 };
 
 static const struct mmio_reg tgl_fivr_mmio_regs[] = {
-	{ 0, 0x5A18, 3, 0x7, 12}, /* vco_ref_code_lo */
+	{ 0, 0x5A18, 3, 0x7, 11}, /* vco_ref_code_lo */
 	{ 0, 0x5A18, 8, 0xFF, 16}, /* vco_ref_code_hi */
 	{ 0, 0x5A08, 8, 0xFF, 0}, /* spread_spectrum_pct */
 	{ 0, 0x5A08, 1, 0x1, 8}, /* spread_spectrum_clk_enable */
@@ -170,6 +172,7 @@
 RFIM_SHOW(rfi_restriction_run_busy, 1)
 RFIM_SHOW(rfi_restriction_err_code, 1)
 RFIM_SHOW(rfi_restriction_data_rate, 1)
+RFIM_SHOW(rfi_restriction_data_rate_base, 1)
 RFIM_SHOW(ddr_data_rate_point_0, 1)
 RFIM_SHOW(ddr_data_rate_point_1, 1)
 RFIM_SHOW(ddr_data_rate_point_2, 1)
@@ -179,11 +182,13 @@
 RFIM_STORE(rfi_restriction_run_busy, 1)
 RFIM_STORE(rfi_restriction_err_code, 1)
 RFIM_STORE(rfi_restriction_data_rate, 1)
+RFIM_STORE(rfi_restriction_data_rate_base, 1)
 RFIM_STORE(rfi_disable, 1)
 
 static DEVICE_ATTR_RW(rfi_restriction_run_busy);
 static DEVICE_ATTR_RW(rfi_restriction_err_code);
 static DEVICE_ATTR_RW(rfi_restriction_data_rate);
+static DEVICE_ATTR_RW(rfi_restriction_data_rate_base);
 static DEVICE_ATTR_RO(ddr_data_rate_point_0);
 static DEVICE_ATTR_RO(ddr_data_rate_point_1);
 static DEVICE_ATTR_RO(ddr_data_rate_point_2);
@@ -194,8 +199,7 @@
 				     struct device_attribute *attr,
 				     const char *buf, size_t count)
 {
-	u16 cmd_id = 0x0008;
-	u32 cmd_resp;
+	u16 id = 0x0008;
 	u32 input;
 	int ret;
 
@@ -203,7 +207,7 @@
 	if (ret)
 		return ret;
 
-	ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, input, &cmd_resp);
+	ret = processor_thermal_send_mbox_write_cmd(to_pci_dev(dev), id, input);
 	if (ret)
 		return ret;
 
@@ -214,30 +218,30 @@
 				    struct device_attribute *attr,
 				    char *buf)
 {
-	u16 cmd_id = 0x0007;
-	u32 cmd_resp;
+	u16 id = 0x0007;
+	u64 resp;
 	int ret;
 
-	ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, 0, &cmd_resp);
+	ret = processor_thermal_send_mbox_read_cmd(to_pci_dev(dev), id, &resp);
 	if (ret)
 		return ret;
 
-	return sprintf(buf, "%u\n", cmd_resp);
+	return sprintf(buf, "%llu\n", resp);
 }
 
 static ssize_t ddr_data_rate_show(struct device *dev,
 				  struct device_attribute *attr,
 				  char *buf)
 {
-	u16 cmd_id = 0x0107;
-	u32 cmd_resp;
+	u16 id = 0x0107;
+	u64 resp;
 	int ret;
 
-	ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, 0, &cmd_resp);
+	ret = processor_thermal_send_mbox_read_cmd(to_pci_dev(dev), id, &resp);
 	if (ret)
 		return ret;
 
-	return sprintf(buf, "%u\n", cmd_resp);
+	return sprintf(buf, "%llu\n", resp);
 }
 
 static DEVICE_ATTR_RW(rfi_restriction);
@@ -247,6 +251,7 @@
 	&dev_attr_rfi_restriction_run_busy.attr,
 	&dev_attr_rfi_restriction_err_code.attr,
 	&dev_attr_rfi_restriction_data_rate.attr,
+	&dev_attr_rfi_restriction_data_rate_base.attr,
 	&dev_attr_ddr_data_rate_point_0.attr,
 	&dev_attr_ddr_data_rate_point_1.attr,
 	&dev_attr_ddr_data_rate_point_2.attr,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/intel_pch_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/intel_pch_thermal.c
@@ -29,6 +29,7 @@
 #define PCH_THERMAL_DID_CNL_LP	0x02F9 /* CNL-LP PCH */
 #define PCH_THERMAL_DID_CML_H	0X06F9 /* CML-H PCH */
 #define PCH_THERMAL_DID_LWB	0xA1B1 /* Lewisburg PCH */
+#define PCH_THERMAL_DID_WBG	0x8D24 /* Wellsburg PCH */
 
 /* Wildcat Point-LP  PCH Thermal registers */
 #define WPT_TEMP	0x0000	/* Temperature */
@@ -345,6 +346,7 @@
 	board_cnl,
 	board_cml,
 	board_lwb,
+	board_wbg,
 };
 
 static const struct board_info {
@@ -375,6 +377,10 @@
 		.name = "pch_lewisburg",
 		.ops = &pch_dev_ops_wpt,
 	},
+	[board_wbg] = {
+		.name = "pch_wellsburg",
+		.ops = &pch_dev_ops_wpt,
+	},
 };
 
 static int intel_pch_thermal_probe(struct pci_dev *pdev,
@@ -490,6 +496,8 @@
 		.driver_data = board_cml, },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_LWB),
 		.driver_data = board_lwb, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WBG),
+		.driver_data = board_wbg, },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/intel_powerclamp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/intel_powerclamp.c
@@ -57,6 +57,7 @@
 
 static unsigned int target_mwait;
 static struct dentry *debug_dir;
+static bool poll_pkg_cstate_enable;
 
 /* user selected target */
 static unsigned int set_target_ratio;
@@ -262,6 +263,9 @@
 {
 	unsigned int comp = 0;
 
+	if (!poll_pkg_cstate_enable)
+		return 0;
+
 	/* we only use compensation if all adjacent ones are good */
 	if (ratio == 1 &&
 		cal_data[ratio].confidence >= CONFIDENCE_OK &&
@@ -531,12 +535,11 @@
 	cpus_read_lock();
 
 	/* prefer BSP */
-	control_cpu = 0;
-	if (!cpu_online(control_cpu))
-		control_cpu = smp_processor_id();
+	control_cpu = cpumask_first(cpu_online_mask);
 
 	clamping = true;
-	schedule_delayed_work(&poll_pkg_cstate_work, 0);
+	if (poll_pkg_cstate_enable)
+		schedule_delayed_work(&poll_pkg_cstate_work, 0);
 
 	/* start one kthread worker per online cpu */
 	for_each_online_cpu(cpu) {
@@ -605,11 +608,15 @@
 static int powerclamp_get_cur_state(struct thermal_cooling_device *cdev,
 				 unsigned long *state)
 {
-	if (true == clamping)
-		*state = pkg_cstate_ratio_cur;
-	else
+	if (clamping) {
+		if (poll_pkg_cstate_enable)
+			*state = pkg_cstate_ratio_cur;
+		else
+			*state = set_target_ratio;
+	} else {
 		/* to save power, do not poll idle ratio while not clamping */
 		*state = -1; /* indicates invalid state */
+	}
 
 	return 0;
 }
@@ -734,6 +741,9 @@
 		goto exit_unregister;
 	}
 
+	if (topology_max_packages() == 1 && topology_max_die_per_package() == 1)
+		poll_pkg_cstate_enable = true;
+
 	cooling_dev = thermal_cooling_device_register("intel_powerclamp", NULL,
 						&powerclamp_cooling_ops);
 	if (IS_ERR(cooling_dev)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/intel_quark_dts_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/intel_quark_dts_thermal.c
@@ -415,22 +415,14 @@
 
 static int __init intel_quark_thermal_init(void)
 {
-	int err = 0;
-
 	if (!x86_match_cpu(qrk_thermal_ids) || !iosf_mbi_available())
 		return -ENODEV;
 
 	soc_dts = alloc_soc_dts();
-	if (IS_ERR(soc_dts)) {
-		err = PTR_ERR(soc_dts);
-		goto err_free;
-	}
+	if (IS_ERR(soc_dts))
+		return PTR_ERR(soc_dts);
 
 	return 0;
-
-err_free:
-	free_soc_dts(soc_dts);
-	return err;
 }
 
 static void __exit intel_quark_thermal_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/intel/intel_soc_dts_iosf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/intel/intel_soc_dts_iosf.c
@@ -405,7 +405,7 @@
 {
 	struct intel_soc_dts_sensors *sensors;
 	bool notification;
-	u32 tj_max;
+	int tj_max;
 	int ret;
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/Kconfig
@@ -34,7 +34,7 @@
 
 config QCOM_LMH
 	tristate "Qualcomm Limits Management Hardware"
-	depends on ARCH_QCOM
+	depends on ARCH_QCOM && QCOM_SCM
 	help
 	  This enables initialization of Qualcomm limits management
 	  hardware(LMh). LMh allows for hardware-enforced mitigation for cpus based on
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/lmh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/lmh.c
@@ -43,7 +43,7 @@
 	if (irq)
 		generic_handle_irq(irq);
 
-	return 0;
+	return IRQ_HANDLED;
 }
 
 static void lmh_enable_interrupt(struct irq_data *d)
@@ -71,7 +71,14 @@
 static int lmh_irq_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
 {
 	struct lmh_hw_data *lmh_data = d->host_data;
+	static struct lock_class_key lmh_lock_key;
+	static struct lock_class_key lmh_request_key;
 
+	/*
+	 * This lock class tells lockdep that GPIO irqs are in a different
+	 * category than their parents, so it won't report false recursion.
+	 */
+	irq_set_lockdep_class(irq, &lmh_lock_key, &lmh_request_key);
 	irq_set_chip_and_handler(irq, &lmh_irq_chip, handle_simple_irq);
 	irq_set_chip_data(irq, lmh_data);
 
@@ -92,6 +99,9 @@
 	int temp_low, temp_high, temp_arm, cpu_id, ret;
 	u32 node_id;
 
+	if (!qcom_scm_is_available())
+		return -EPROBE_DEFER;
+
 	lmh_data = devm_kzalloc(dev, sizeof(*lmh_data), GFP_KERNEL);
 	if (!lmh_data)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -251,7 +251,8 @@
 			disable_s2_shutdown = true;
 		else
 			dev_warn(chip->dev,
-				 "No ADC is configured and critical temperature is above the maximum stage 2 threshold of 140 C! Configuring stage 2 shutdown at 140 C.\n");
+				 "No ADC is configured and critical temperature %d mC is above the maximum stage 2 threshold of %ld mC! Configuring stage 2 shutdown at %ld mC.\n",
+				 temp, stage2_threshold_max, stage2_threshold_max);
 	}
 
 skip:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/tsens-v0_1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/tsens-v0_1.c
@@ -285,7 +285,7 @@
 	u32 p1[10], p2[10];
 	int mode = 0;
 	u32 *qfprom_cdata;
-	u32 cdata[6];
+	u32 cdata[4];
 
 	qfprom_cdata = (u32 *)qfprom_read(priv->dev, "calib");
 	if (IS_ERR(qfprom_cdata))
@@ -296,8 +296,6 @@
 	cdata[1] = qfprom_cdata[13];
 	cdata[2] = qfprom_cdata[0];
 	cdata[3] = qfprom_cdata[1];
-	cdata[4] = qfprom_cdata[22];
-	cdata[5] = qfprom_cdata[21];
 
 	mode = (cdata[0] & MSM8939_CAL_SEL_MASK) >> MSM8939_CAL_SEL_SHIFT;
 	dev_dbg(priv->dev, "calibration mode is %d\n", mode);
@@ -314,8 +312,6 @@
 		p2[6] = (cdata[2] & MSM8939_S6_P2_MASK) >> MSM8939_S6_P2_SHIFT;
 		p2[7] = (cdata[3] & MSM8939_S7_P2_MASK) >> MSM8939_S7_P2_SHIFT;
 		p2[8] = (cdata[3] & MSM8939_S8_P2_MASK) >> MSM8939_S8_P2_SHIFT;
-		p2[9] = (cdata[4] & MSM8939_S9_P2_MASK_0_4) >> MSM8939_S9_P2_SHIFT_0_4;
-		p2[9] |= ((cdata[5] & MSM8939_S9_P2_MASK_5) >> MSM8939_S9_P2_SHIFT_5) << 5;
 		for (i = 0; i < priv->num_sensors; i++)
 			p2[i] = (base1 + p2[i]) << 2;
 		fallthrough;
@@ -331,7 +327,6 @@
 		p1[6] = (cdata[2] & MSM8939_S6_P1_MASK) >> MSM8939_S6_P1_SHIFT;
 		p1[7] = (cdata[3] & MSM8939_S7_P1_MASK) >> MSM8939_S7_P1_SHIFT;
 		p1[8] = (cdata[3] & MSM8939_S8_P1_MASK) >> MSM8939_S8_P1_SHIFT;
-		p1[9] = (cdata[4] & MSM8939_S9_P1_MASK) >> MSM8939_S9_P1_SHIFT;
 		for (i = 0; i < priv->num_sensors; i++)
 			p1[i] = ((base0) + p1[i]) << 2;
 		break;
@@ -534,6 +529,21 @@
 	return 0;
 }
 
+static int __init init_8939(struct tsens_priv *priv) {
+	priv->sensor[0].slope = 2911;
+	priv->sensor[1].slope = 2789;
+	priv->sensor[2].slope = 2906;
+	priv->sensor[3].slope = 2763;
+	priv->sensor[4].slope = 2922;
+	priv->sensor[5].slope = 2867;
+	priv->sensor[6].slope = 2833;
+	priv->sensor[7].slope = 2838;
+	priv->sensor[8].slope = 2840;
+	/* priv->sensor[9].slope = 2852; */
+
+	return init_common(priv);
+}
+
 /* v0.1: 8916, 8939, 8974, 9607 */
 
 static struct tsens_features tsens_v0_1_feat = {
@@ -596,15 +606,15 @@
 };
 
 static const struct tsens_ops ops_8939 = {
-	.init		= init_common,
+	.init		= init_8939,
 	.calibrate	= calibrate_8939,
 	.get_temp	= get_temp_common,
 };
 
 struct tsens_plat_data data_8939 = {
-	.num_sensors	= 10,
+	.num_sensors	= 9,
 	.ops		= &ops_8939,
-	.hw_ids		= (unsigned int []){ 0, 1, 2, 4, 5, 6, 7, 8, 9, 10 },
+	.hw_ids		= (unsigned int []){ 0, 1, 2, 3, 5, 6, 7, 8, 9, /* 10 */ },
 
 	.feat		= &tsens_v0_1_feat,
 	.fields	= tsens_v0_1_regfields,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/tsens-v1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/tsens-v1.c
@@ -78,11 +78,6 @@
 
 #define MSM8976_CAL_SEL_MASK	0x3
 
-#define MSM8976_CAL_DEGC_PT1	30
-#define MSM8976_CAL_DEGC_PT2	120
-#define MSM8976_SLOPE_FACTOR	1000
-#define MSM8976_SLOPE_DEFAULT	3200
-
 /* eeprom layout data for qcs404/405 (v1) */
 #define BASE0_MASK	0x000007f8
 #define BASE1_MASK	0x0007f800
@@ -142,30 +137,6 @@
 #define CAL_SEL_MASK	7
 #define CAL_SEL_SHIFT	0
 
-static void compute_intercept_slope_8976(struct tsens_priv *priv,
-			      u32 *p1, u32 *p2, u32 mode)
-{
-	int i;
-
-	priv->sensor[0].slope = 3313;
-	priv->sensor[1].slope = 3275;
-	priv->sensor[2].slope = 3320;
-	priv->sensor[3].slope = 3246;
-	priv->sensor[4].slope = 3279;
-	priv->sensor[5].slope = 3257;
-	priv->sensor[6].slope = 3234;
-	priv->sensor[7].slope = 3269;
-	priv->sensor[8].slope = 3255;
-	priv->sensor[9].slope = 3239;
-	priv->sensor[10].slope = 3286;
-
-	for (i = 0; i < priv->num_sensors; i++) {
-		priv->sensor[i].offset = (p1[i] * MSM8976_SLOPE_FACTOR) -
-				(MSM8976_CAL_DEGC_PT1 *
-				priv->sensor[i].slope);
-	}
-}
-
 static int calibrate_v1(struct tsens_priv *priv)
 {
 	u32 base0 = 0, base1 = 0;
@@ -291,7 +262,7 @@
 		break;
 	}
 
-	compute_intercept_slope_8976(priv, p1, p2, mode);
+	compute_intercept_slope(priv, p1, p2, mode);
 	kfree(qfprom_cdata);
 
 	return 0;
@@ -362,6 +333,22 @@
 	[TRDY] = REG_FIELD(TM_TRDY_OFF, 0, 0),
 };
 
+static int __init init_8956(struct tsens_priv *priv) {
+	priv->sensor[0].slope = 3313;
+	priv->sensor[1].slope = 3275;
+	priv->sensor[2].slope = 3320;
+	priv->sensor[3].slope = 3246;
+	priv->sensor[4].slope = 3279;
+	priv->sensor[5].slope = 3257;
+	priv->sensor[6].slope = 3234;
+	priv->sensor[7].slope = 3269;
+	priv->sensor[8].slope = 3255;
+	priv->sensor[9].slope = 3239;
+	priv->sensor[10].slope = 3286;
+
+	return init_common(priv);
+}
+
 static const struct tsens_ops ops_generic_v1 = {
 	.init		= init_common,
 	.calibrate	= calibrate_v1,
@@ -374,13 +361,25 @@
 	.fields	= tsens_v1_regfields,
 };
 
+static const struct tsens_ops ops_8956 = {
+	.init		= init_8956,
+	.calibrate	= calibrate_8976,
+	.get_temp	= get_temp_tsens_valid,
+};
+
+struct tsens_plat_data data_8956 = {
+	.num_sensors	= 11,
+	.ops		= &ops_8956,
+	.feat		= &tsens_v1_feat,
+	.fields		= tsens_v1_regfields,
+};
+
 static const struct tsens_ops ops_8976 = {
 	.init		= init_common,
 	.calibrate	= calibrate_8976,
 	.get_temp	= get_temp_tsens_valid,
 };
 
-/* Valid for both MSM8956 and MSM8976. */
 struct tsens_plat_data data_8976 = {
 	.num_sensors	= 11,
 	.ops		= &ops_8976,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/tsens.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/tsens.c
@@ -84,7 +84,7 @@
 	for (i = 0; i < priv->num_sensors; i++) {
 		dev_dbg(priv->dev,
 			"%s: sensor%d - data_point1:%#x data_point2:%#x\n",
-			__func__, i, p1[i], p2[i]);
+			__func__, i, p1[i], p2 ? p2[i] : 0);
 
 		if (!priv->sensor[i].slope)
 			priv->sensor[i].slope = SLOPE_DEFAULT;
@@ -603,22 +603,21 @@
 	int ret;
 
 	/* VER_0 doesn't have VALID bit */
-	if (tsens_version(priv) >= VER_0_1) {
-		ret = regmap_field_read(priv->rf[valid_idx], &valid);
-		if (ret)
-			return ret;
-		while (!valid) {
-			/* Valid bit is 0 for 6 AHB clock cycles.
-			 * At 19.2MHz, 1 AHB clock is ~60ns.
-			 * We should enter this loop very, very rarely.
-			 */
-			ndelay(400);
-			ret = regmap_field_read(priv->rf[valid_idx], &valid);
-			if (ret)
-				return ret;
-		}
-	}
+	if (tsens_version(priv) == VER_0)
+		goto get_temp;
+
+	/* Valid bit is 0 for 6 AHB clock cycles.
+	 * At 19.2MHz, 1 AHB clock is ~60ns.
+	 * We should enter this loop very, very rarely.
+	 * Wait 1 us since it's the min of poll_timeout macro.
+	 * Old value was 400 ns.
+	 */
+	ret = regmap_field_read_poll_timeout(priv->rf[valid_idx], valid,
+					     valid, 1, 20 * USEC_PER_MSEC);
+	if (ret)
+		return ret;
 
+get_temp:
 	/* Valid bit is set, OK to read the temperature */
 	*temp = tsens_hw_to_mC(s, temp_idx);
 
@@ -980,6 +979,12 @@
 		.compatible = "qcom,msm8939-tsens",
 		.data = &data_8939,
 	}, {
+		.compatible = "qcom,msm8956-tsens",
+		.data = &data_8956,
+	}, {
+		.compatible = "qcom,msm8960-tsens",
+		.data = &data_8960,
+	}, {
 		.compatible = "qcom,msm8974-tsens",
 		.data = &data_8974,
 	}, {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/qcom/tsens.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/qcom/tsens.h
@@ -590,7 +590,7 @@
 extern struct tsens_plat_data data_8916, data_8939, data_8974, data_9607;
 
 /* TSENS v1 targets */
-extern struct tsens_plat_data data_tsens_v1, data_8976;
+extern struct tsens_plat_data data_tsens_v1, data_8976, data_8956;
 
 /* TSENS v2 targets */
 extern struct tsens_plat_data data_8996, data_tsens_v2;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/sun8i_thermal.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/sun8i_thermal.c
@@ -319,6 +319,11 @@
 	return ret;
 }
 
+static void sun8i_ths_reset_control_assert(void *data)
+{
+	reset_control_assert(data);
+}
+
 static int sun8i_ths_resource_init(struct ths_device *tmdev)
 {
 	struct device *dev = tmdev->dev;
@@ -339,47 +344,35 @@
 		if (IS_ERR(tmdev->reset))
 			return PTR_ERR(tmdev->reset);
 
-		tmdev->bus_clk = devm_clk_get(&pdev->dev, "bus");
+		ret = reset_control_deassert(tmdev->reset);
+		if (ret)
+			return ret;
+
+		ret = devm_add_action_or_reset(dev, sun8i_ths_reset_control_assert,
+					       tmdev->reset);
+		if (ret)
+			return ret;
+
+		tmdev->bus_clk = devm_clk_get_enabled(&pdev->dev, "bus");
 		if (IS_ERR(tmdev->bus_clk))
 			return PTR_ERR(tmdev->bus_clk);
 	}
 
 	if (tmdev->chip->has_mod_clk) {
-		tmdev->mod_clk = devm_clk_get(&pdev->dev, "mod");
+		tmdev->mod_clk = devm_clk_get_enabled(&pdev->dev, "mod");
 		if (IS_ERR(tmdev->mod_clk))
 			return PTR_ERR(tmdev->mod_clk);
 	}
 
-	ret = reset_control_deassert(tmdev->reset);
-	if (ret)
-		return ret;
-
-	ret = clk_prepare_enable(tmdev->bus_clk);
-	if (ret)
-		goto assert_reset;
-
 	ret = clk_set_rate(tmdev->mod_clk, 24000000);
 	if (ret)
-		goto bus_disable;
-
-	ret = clk_prepare_enable(tmdev->mod_clk);
-	if (ret)
-		goto bus_disable;
+		return ret;
 
 	ret = sun8i_ths_calibrate(tmdev);
 	if (ret)
-		goto mod_disable;
+		return ret;
 
 	return 0;
-
-mod_disable:
-	clk_disable_unprepare(tmdev->mod_clk);
-bus_disable:
-	clk_disable_unprepare(tmdev->bus_clk);
-assert_reset:
-	reset_control_assert(tmdev->reset);
-
-	return ret;
 }
 
 static int sun8i_h3_thermal_init(struct ths_device *tmdev)
@@ -530,17 +523,6 @@
 	return 0;
 }
 
-static int sun8i_ths_remove(struct platform_device *pdev)
-{
-	struct ths_device *tmdev = platform_get_drvdata(pdev);
-
-	clk_disable_unprepare(tmdev->mod_clk);
-	clk_disable_unprepare(tmdev->bus_clk);
-	reset_control_assert(tmdev->reset);
-
-	return 0;
-}
-
 static const struct ths_thermal_chip sun8i_a83t_ths = {
 	.sensor_num = 3,
 	.scale = 705,
@@ -642,7 +624,6 @@
 
 static struct platform_driver ths_driver = {
 	.probe = sun8i_ths_probe,
-	.remove = sun8i_ths_remove,
 	.driver = {
 		.name = "sun8i-thermal",
 		.of_match_table = of_ths_match,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/tegra/tegra30-tsensor.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/tegra/tegra30-tsensor.c
@@ -316,7 +316,7 @@
 	*hot_trip  = 85000;
 	*crit_trip = 90000;
 
-	for (i = 0; i < tzd->trips; i++) {
+	for (i = 0; i < tzd->num_trips; i++) {
 		enum thermal_trip_type type;
 		int trip_temp;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/thermal_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/thermal_core.c
@@ -419,6 +419,8 @@
 {
 	struct thermal_instance *pos;
 	tz->temperature = THERMAL_TEMP_INVALID;
+	tz->prev_low_trip = -INT_MAX;
+	tz->prev_high_trip = INT_MAX;
 	list_for_each_entry(pos, &tz->thermal_instances, tz_node)
 		pos->initialized = false;
 }
@@ -501,7 +503,7 @@
 
 	tz->notify_event = event;
 
-	for (count = 0; count < tz->trips; count++)
+	for (count = 0; count < tz->num_trips; count++)
 		handle_thermal_trip(tz, count);
 }
 EXPORT_SYMBOL_GPL(thermal_zone_device_update);
@@ -623,10 +625,9 @@
 	struct thermal_instance *pos;
 	struct thermal_zone_device *pos1;
 	struct thermal_cooling_device *pos2;
-	unsigned long max_state;
-	int result, ret;
+	int result;
 
-	if (trip >= tz->trips || trip < 0)
+	if (trip >= tz->num_trips || trip < 0)
 		return -EINVAL;
 
 	list_for_each_entry(pos1, &thermal_tz_list, node) {
@@ -641,15 +642,11 @@
 	if (tz != pos1 || cdev != pos2)
 		return -EINVAL;
 
-	ret = cdev->ops->get_max_state(cdev, &max_state);
-	if (ret)
-		return ret;
-
 	/* lower default 0, upper default max_state */
 	lower = lower == THERMAL_NO_LIMIT ? 0 : lower;
-	upper = upper == THERMAL_NO_LIMIT ? max_state : upper;
+	upper = upper == THERMAL_NO_LIMIT ? cdev->max_state : upper;
 
-	if (lower > upper || upper > max_state)
+	if (lower > upper || upper > cdev->max_state)
 		return -EINVAL;
 
 	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
@@ -674,7 +671,8 @@
 	if (result)
 		goto release_ida;
 
-	sprintf(dev->attr_name, "cdev%d_trip_point", dev->id);
+	snprintf(dev->attr_name, sizeof(dev->attr_name), "cdev%d_trip_point",
+		 dev->id);
 	sysfs_attr_init(&dev->attr.attr);
 	dev->attr.attr.name = dev->attr_name;
 	dev->attr.attr.mode = 0444;
@@ -683,7 +681,8 @@
 	if (result)
 		goto remove_symbol_link;
 
-	sprintf(dev->weight_attr_name, "cdev%d_weight", dev->id);
+	snprintf(dev->weight_attr_name, sizeof(dev->weight_attr_name),
+		 "cdev%d_weight", dev->id);
 	sysfs_attr_init(&dev->weight_attr.attr);
 	dev->weight_attr.attr.name = dev->weight_attr_name;
 	dev->weight_attr.attr.mode = S_IWUSR | S_IRUGO;
@@ -807,7 +806,7 @@
 {
 	int i, ret;
 
-	for (i = 0; i < tz->trips; i++) {
+	for (i = 0; i < tz->num_trips; i++) {
 		if (mask & (1 << i)) {
 			unsigned long upper, lower;
 
@@ -887,7 +886,7 @@
 {
 	struct thermal_cooling_device *cdev;
 	struct thermal_zone_device *pos = NULL;
-	int ret;
+	int id, ret;
 
 	if (!ops || !ops->get_max_state || !ops->get_cur_state ||
 	    !ops->set_cur_state)
@@ -901,6 +900,7 @@
 	if (ret < 0)
 		goto out_kfree_cdev;
 	cdev->id = ret;
+	id = ret;
 
 	cdev->type = kstrdup(type ? type : "", GFP_KERNEL);
 	if (!cdev->type) {
@@ -915,8 +915,22 @@
 	cdev->updated = false;
 	cdev->device.class = &thermal_class;
 	cdev->devdata = devdata;
+
+	ret = cdev->ops->get_max_state(cdev, &cdev->max_state);
+	if (ret) {
+		kfree(cdev->type);
+		goto out_ida_remove;
+	}
+
 	thermal_cooling_device_setup_sysfs(cdev);
-	dev_set_name(&cdev->device, "cooling_device%d", cdev->id);
+
+	ret = dev_set_name(&cdev->device, "cooling_device%d", cdev->id);
+	if (ret) {
+		kfree(cdev->type);
+		thermal_cooling_device_destroy_sysfs(cdev);
+		goto out_ida_remove;
+	}
+
 	ret = device_register(&cdev->device);
 	if (ret)
 		goto out_kfree_type;
@@ -939,10 +953,14 @@
 	return cdev;
 
 out_kfree_type:
+	thermal_cooling_device_destroy_sysfs(cdev);
 	kfree(cdev->type);
 	put_device(&cdev->device);
+
+	/* thermal_release() takes care of the rest */
+	cdev = NULL;
 out_ida_remove:
-	ida_simple_remove(&thermal_cdev_ida, cdev->id);
+	ida_simple_remove(&thermal_cdev_ida, id);
 out_kfree_cdev:
 	kfree(cdev);
 	return ERR_PTR(ret);
@@ -1047,7 +1065,7 @@
 {
 	int i;
 
-	for (i = 0; i < tz->trips; i++)
+	for (i = 0; i < tz->num_trips; i++)
 		if (mask & (1 << i))
 			thermal_zone_unbind_cooling_device(tz, i, cdev);
 }
@@ -1152,7 +1170,7 @@
 /**
  * thermal_zone_device_register() - register a new thermal zone device
  * @type:	the thermal zone device type
- * @trips:	the number of trip points the thermal zone support
+ * @num_trips:	the number of trip points the thermal zone support
  * @mask:	a bit string indicating the writeablility of trip points
  * @devdata:	private device data
  * @ops:	standard thermal zone device callbacks
@@ -1174,7 +1192,7 @@
  * IS_ERR*() helpers.
  */
 struct thermal_zone_device *
-thermal_zone_device_register(const char *type, int trips, int mask,
+thermal_zone_device_register(const char *type, int num_trips, int mask,
 			     void *devdata, struct thermal_zone_device_ops *ops,
 			     struct thermal_zone_params *tzp, int passive_delay,
 			     int polling_delay)
@@ -1188,27 +1206,27 @@
 	struct thermal_governor *governor;
 
 	if (!type || strlen(type) == 0) {
-		pr_err("Error: No thermal zone type defined\n");
+		pr_err("No thermal zone type defined\n");
 		return ERR_PTR(-EINVAL);
 	}
 
 	if (type && strlen(type) >= THERMAL_NAME_LENGTH) {
-		pr_err("Error: Thermal zone name (%s) too long, should be under %d chars\n",
+		pr_err("Thermal zone name (%s) too long, should be under %d chars\n",
 		       type, THERMAL_NAME_LENGTH);
 		return ERR_PTR(-EINVAL);
 	}
 
-	if (trips > THERMAL_MAX_TRIPS || trips < 0 || mask >> trips) {
-		pr_err("Error: Incorrect number of thermal trips\n");
+	if (num_trips > THERMAL_MAX_TRIPS || num_trips < 0 || mask >> num_trips) {
+		pr_err("Incorrect number of thermal trips\n");
 		return ERR_PTR(-EINVAL);
 	}
 
 	if (!ops) {
-		pr_err("Error: Thermal zone device ops not defined\n");
+		pr_err("Thermal zone device ops not defined\n");
 		return ERR_PTR(-EINVAL);
 	}
 
-	if (trips > 0 && (!ops->get_trip_type || !ops->get_trip_temp))
+	if (num_trips > 0 && (!ops->get_trip_type || !ops->get_trip_temp))
 		return ERR_PTR(-EINVAL);
 
 	tz = kzalloc(sizeof(*tz), GFP_KERNEL);
@@ -1234,7 +1252,7 @@
 	tz->tzp = tzp;
 	tz->device.class = &thermal_class;
 	tz->devdata = devdata;
-	tz->trips = trips;
+	tz->num_trips = num_trips;
 
 	thermal_set_delay_jiffies(&tz->passive_delay_jiffies, passive_delay);
 	thermal_set_delay_jiffies(&tz->polling_delay_jiffies, polling_delay);
@@ -1248,12 +1266,17 @@
 	/* A new thermal zone needs to be updated anyway. */
 	atomic_set(&tz->need_update, 1);
 
-	dev_set_name(&tz->device, "thermal_zone%d", tz->id);
+	result = dev_set_name(&tz->device, "thermal_zone%d", tz->id);
+	if (result) {
+		thermal_zone_destroy_device_groups(tz);
+		goto remove_id;
+	}
+	thermal_zone_device_init(tz);
 	result = device_register(&tz->device);
 	if (result)
 		goto release_device;
 
-	for (count = 0; count < trips; count++) {
+	for (count = 0; count < num_trips; count++) {
 		if (tz->ops->get_trip_type(tz, count, &trip_type) ||
 		    tz->ops->get_trip_temp(tz, count, &trip_temp) ||
 		    !trip_temp)
@@ -1291,7 +1314,6 @@
 
 	INIT_DELAYED_WORK(&tz->poll_queue, thermal_zone_device_check);
 
-	thermal_zone_device_init(tz);
 	/* Update the new thermal zone and mark it as already updated. */
 	if (atomic_cmpxchg(&tz->need_update, 1, 0))
 		thermal_zone_device_update(tz, THERMAL_EVENT_UNSPECIFIED);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/thermal_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/thermal_helpers.c
@@ -90,7 +90,7 @@
 	ret = tz->ops->get_temp(tz, temp);
 
 	if (IS_ENABLED(CONFIG_THERMAL_EMULATION) && tz->emul_temperature) {
-		for (count = 0; count < tz->trips; count++) {
+		for (count = 0; count < tz->num_trips; count++) {
 			ret = tz->ops->get_trip_type(tz, count, &type);
 			if (!ret && type == THERMAL_TRIP_CRITICAL) {
 				ret = tz->ops->get_trip_temp(tz, count,
@@ -138,7 +138,7 @@
 	if (!tz->ops->set_trips || !tz->ops->get_trip_hyst)
 		goto exit;
 
-	for (i = 0; i < tz->trips; i++) {
+	for (i = 0; i < tz->num_trips; i++) {
 		int trip_low;
 
 		tz->ops->get_trip_temp(tz, i, &trip_temp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/thermal_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/thermal_netlink.c
@@ -415,14 +415,15 @@
 
 	mutex_lock(&tz->lock);
 
-	for (i = 0; i < tz->trips; i++) {
+	for (i = 0; i < tz->num_trips; i++) {
 
 		enum thermal_trip_type type;
-		int temp, hyst;
+		int temp, hyst = 0;
 
 		tz->ops->get_trip_type(tz, i, &type);
 		tz->ops->get_trip_temp(tz, i, &temp);
-		tz->ops->get_trip_hyst(tz, i, &hyst);
+		if (tz->ops->get_trip_hyst)
+			tz->ops->get_trip_hyst(tz, i, &hyst);
 
 		if (nla_put_u32(msg, THERMAL_GENL_ATTR_TZ_TRIP_ID, i) ||
 		    nla_put_u32(msg, THERMAL_GENL_ATTR_TZ_TRIP_TYPE, type) ||
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/thermal_of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/thermal_of.c
@@ -89,7 +89,7 @@
 {
 	struct __thermal_zone *data = tz->devdata;
 
-	if (!data->ops->get_temp)
+	if (!data->ops || !data->ops->get_temp)
 		return -EINVAL;
 
 	return data->ops->get_temp(data->sensor_data, temp);
@@ -186,6 +186,9 @@
 {
 	struct __thermal_zone *data = tz->devdata;
 
+	if (!data->ops || !data->ops->set_emul_temp)
+		return -EINVAL;
+
 	return data->ops->set_emul_temp(data->sensor_data, temp);
 }
 
@@ -194,7 +197,7 @@
 {
 	struct __thermal_zone *data = tz->devdata;
 
-	if (!data->ops->get_trend)
+	if (!data->ops || !data->ops->get_trend)
 		return -EINVAL;
 
 	return data->ops->get_trend(data->sensor_data, trip, trend);
@@ -301,7 +304,7 @@
 	if (trip >= data->ntrips || trip < 0)
 		return -EDOM;
 
-	if (data->ops->set_trip_temp) {
+	if (data->ops && data->ops->set_trip_temp) {
 		int ret;
 
 		ret = data->ops->set_trip_temp(data->sensor_data, trip, temp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thermal/thermal_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thermal/thermal_sysfs.c
@@ -416,15 +416,15 @@
 	int indx;
 
 	/* This function works only for zones with at least one trip */
-	if (tz->trips <= 0)
+	if (tz->num_trips <= 0)
 		return -EINVAL;
 
-	tz->trip_type_attrs = kcalloc(tz->trips, sizeof(*tz->trip_type_attrs),
+	tz->trip_type_attrs = kcalloc(tz->num_trips, sizeof(*tz->trip_type_attrs),
 				      GFP_KERNEL);
 	if (!tz->trip_type_attrs)
 		return -ENOMEM;
 
-	tz->trip_temp_attrs = kcalloc(tz->trips, sizeof(*tz->trip_temp_attrs),
+	tz->trip_temp_attrs = kcalloc(tz->num_trips, sizeof(*tz->trip_temp_attrs),
 				      GFP_KERNEL);
 	if (!tz->trip_temp_attrs) {
 		kfree(tz->trip_type_attrs);
@@ -432,7 +432,7 @@
 	}
 
 	if (tz->ops->get_trip_hyst) {
-		tz->trip_hyst_attrs = kcalloc(tz->trips,
+		tz->trip_hyst_attrs = kcalloc(tz->num_trips,
 					      sizeof(*tz->trip_hyst_attrs),
 					      GFP_KERNEL);
 		if (!tz->trip_hyst_attrs) {
@@ -442,7 +442,7 @@
 		}
 	}
 
-	attrs = kcalloc(tz->trips * 3 + 1, sizeof(*attrs), GFP_KERNEL);
+	attrs = kcalloc(tz->num_trips * 3 + 1, sizeof(*attrs), GFP_KERNEL);
 	if (!attrs) {
 		kfree(tz->trip_type_attrs);
 		kfree(tz->trip_temp_attrs);
@@ -451,7 +451,7 @@
 		return -ENOMEM;
 	}
 
-	for (indx = 0; indx < tz->trips; indx++) {
+	for (indx = 0; indx < tz->num_trips; indx++) {
 		/* create trip type attribute */
 		snprintf(tz->trip_type_attrs[indx].name, THERMAL_NAME_LENGTH,
 			 "trip_point_%d_type", indx);
@@ -478,7 +478,7 @@
 			tz->trip_temp_attrs[indx].attr.store =
 							trip_point_temp_store;
 		}
-		attrs[indx + tz->trips] = &tz->trip_temp_attrs[indx].attr.attr;
+		attrs[indx + tz->num_trips] = &tz->trip_temp_attrs[indx].attr.attr;
 
 		/* create Optional trip hyst attribute */
 		if (!tz->ops->get_trip_hyst)
@@ -496,10 +496,10 @@
 			tz->trip_hyst_attrs[indx].attr.store =
 					trip_point_hyst_store;
 		}
-		attrs[indx + tz->trips * 2] =
+		attrs[indx + tz->num_trips * 2] =
 					&tz->trip_hyst_attrs[indx].attr.attr;
 	}
-	attrs[tz->trips * 3] = NULL;
+	attrs[tz->num_trips * 3] = NULL;
 
 	tz->trips_attribute_group.attrs = attrs;
 
@@ -540,7 +540,7 @@
 	for (i = 0; i < size - 2; i++)
 		groups[i] = thermal_zone_attribute_groups[i];
 
-	if (tz->trips) {
+	if (tz->num_trips) {
 		result = create_trip_attrs(tz, mask);
 		if (result) {
 			kfree(groups);
@@ -561,7 +561,7 @@
 	if (!tz)
 		return;
 
-	if (tz->trips)
+	if (tz->num_trips)
 		destroy_trip_attrs(tz);
 
 	kfree(tz->device.groups);
@@ -580,13 +580,8 @@
 			      char *buf)
 {
 	struct thermal_cooling_device *cdev = to_cooling_device(dev);
-	unsigned long state;
-	int ret;
 
-	ret = cdev->ops->get_max_state(cdev, &state);
-	if (ret)
-		return ret;
-	return sprintf(buf, "%ld\n", state);
+	return sprintf(buf, "%ld\n", cdev->max_state);
 }
 
 static ssize_t cur_state_show(struct device *dev, struct device_attribute *attr,
@@ -616,6 +611,10 @@
 	if ((long)state < 0)
 		return -EINVAL;
 
+	/* Requested state should be less than max_state + 1 */
+	if (state > cdev->max_state)
+		return -EINVAL;
+
 	mutex_lock(&cdev->lock);
 
 	result = cdev->ops->set_cur_state(cdev, state);
@@ -813,12 +812,13 @@
 
 static void cooling_device_stats_setup(struct thermal_cooling_device *cdev)
 {
+	const struct attribute_group *stats_attr_group = NULL;
 	struct cooling_dev_stats *stats;
 	unsigned long states;
 	int var;
 
 	if (cdev->ops->get_max_state(cdev, &states))
-		return;
+		goto out;
 
 	states++; /* Total number of states is highest state + 1 */
 
@@ -828,7 +828,7 @@
 
 	stats = kzalloc(var, GFP_KERNEL);
 	if (!stats)
-		return;
+		goto out;
 
 	stats->time_in_state = (ktime_t *)(stats + 1);
 	stats->trans_table = (unsigned int *)(stats->time_in_state + states);
@@ -838,9 +838,12 @@
 
 	spin_lock_init(&stats->lock);
 
+	stats_attr_group = &cooling_device_stats_attr_group;
+
+out:
 	/* Fill the empty slot left in cooling_device_attr_groups */
 	var = ARRAY_SIZE(cooling_device_attr_groups) - 2;
-	cooling_device_attr_groups[var] = &cooling_device_stats_attr_group;
+	cooling_device_attr_groups[var] = stats_attr_group;
 }
 
 static void cooling_device_stats_destroy(struct thermal_cooling_device *cdev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/acpi.c
@@ -7,6 +7,7 @@
  */
 
 #include <linux/acpi.h>
+#include <linux/pm_runtime.h>
 
 #include "tb.h"
 
@@ -74,8 +75,18 @@
 		 pci_pcie_type(pdev) == PCI_EXP_TYPE_DOWNSTREAM))) {
 		const struct device_link *link;
 
+		/*
+		 * Make them both active first to make sure the NHI does
+		 * not runtime suspend before the consumer. The
+		 * pm_runtime_put() below then allows the consumer to
+		 * runtime suspend again (which then allows NHI runtime
+		 * suspend too now that the device link is established).
+		 */
+		pm_runtime_get_sync(&pdev->dev);
+
 		link = device_link_add(&pdev->dev, &nhi->pdev->dev,
 				       DL_FLAG_AUTOREMOVE_SUPPLIER |
+				       DL_FLAG_RPM_ACTIVE |
 				       DL_FLAG_PM_RUNTIME);
 		if (link) {
 			dev_dbg(&nhi->pdev->dev, "created link from %s\n",
@@ -84,6 +95,8 @@
 			dev_warn(&nhi->pdev->dev, "device link creation from %s failed\n",
 				 dev_name(&pdev->dev));
 		}
+
+		pm_runtime_put(&pdev->dev);
 	}
 
 out_put:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/ctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/ctl.c
@@ -17,7 +17,7 @@
 
 
 #define TB_CTL_RX_PKG_COUNT	10
-#define TB_CTL_RETRIES		1
+#define TB_CTL_RETRIES		4
 
 /**
  * struct tb_ctl - Thunderbolt control channel
@@ -408,7 +408,7 @@
 
 static int tb_async_error(const struct ctl_pkg *pkg)
 {
-	const struct cfg_error_pkg *error = (const struct cfg_error_pkg *)pkg;
+	const struct cfg_error_pkg *error = pkg->buffer;
 
 	if (pkg->frame.eof != TB_CFG_PKG_ERROR)
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/dma_test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/dma_test.c
@@ -192,9 +192,9 @@
 	}
 
 	ret = tb_xdomain_enable_paths(dt->xd, dt->tx_hopid,
-				      dt->tx_ring ? dt->tx_ring->hop : 0,
+				      dt->tx_ring ? dt->tx_ring->hop : -1,
 				      dt->rx_hopid,
-				      dt->rx_ring ? dt->rx_ring->hop : 0);
+				      dt->rx_ring ? dt->rx_ring->hop : -1);
 	if (ret) {
 		dma_test_free_rings(dt);
 		return ret;
@@ -218,9 +218,9 @@
 		tb_ring_stop(dt->tx_ring);
 
 	ret = tb_xdomain_disable_paths(dt->xd, dt->tx_hopid,
-				       dt->tx_ring ? dt->tx_ring->hop : 0,
+				       dt->tx_ring ? dt->tx_ring->hop : -1,
 				       dt->rx_hopid,
-				       dt->rx_ring ? dt->rx_ring->hop : 0);
+				       dt->rx_ring ? dt->rx_ring->hop : -1);
 	if (ret)
 		dev_warn(&dt->svc->dev, "failed to disable DMA paths\n");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/eeprom.c
@@ -553,9 +553,9 @@
 	crc = tb_crc8((u8 *) &header->uid, 8);
 	if (crc != header->uid_crc8) {
 		tb_sw_warn(sw,
-			"DROM UID CRC8 mismatch (expected: %#x, got: %#x), aborting\n",
+			"DROM UID CRC8 mismatch (expected: %#x, got: %#x)\n",
 			header->uid_crc8, crc);
-		return -EINVAL;
+		return -EILSEQ;
 	}
 	if (!sw->uid)
 		sw->uid = header->uid;
@@ -654,6 +654,7 @@
 	sw->drom = kzalloc(size, GFP_KERNEL);
 	if (!sw->drom)
 		return -ENOMEM;
+read:
 	res = tb_drom_read_n(sw, 0, sw->drom, size);
 	if (res)
 		goto err;
@@ -662,7 +663,11 @@
 	header = (void *) sw->drom;
 
 	if (header->data_len + TB_DROM_DATA_START != size) {
-		tb_sw_warn(sw, "drom size mismatch, aborting\n");
+		tb_sw_warn(sw, "drom size mismatch\n");
+		if (retries--) {
+			msleep(100);
+			goto read;
+		}
 		goto err;
 	}
 
@@ -683,11 +688,9 @@
 
 	/* If the DROM parsing fails, wait a moment and retry once */
 	if (res == -EILSEQ && retries--) {
-		tb_sw_warn(sw, "parsing DROM failed, retrying\n");
+		tb_sw_warn(sw, "parsing DROM failed\n");
 		msleep(100);
-		res = tb_drom_read_n(sw, 0, sw->drom, size);
-		if (!res)
-			goto parse;
+		goto read;
 	}
 
 	if (!res)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/icm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/icm.c
@@ -41,6 +41,7 @@
 #define PHY_PORT_CS1_LINK_STATE_SHIFT	26
 
 #define ICM_TIMEOUT			5000	/* ms */
+#define ICM_RETRIES			3
 #define ICM_APPROVE_TIMEOUT		10000	/* ms */
 #define ICM_MAX_LINK			4
 
@@ -296,10 +297,9 @@
 
 static int icm_request(struct tb *tb, const void *request, size_t request_size,
 		       void *response, size_t response_size, size_t npackets,
-		       unsigned int timeout_msec)
+		       int retries, unsigned int timeout_msec)
 {
 	struct icm *icm = tb_priv(tb);
-	int retries = 3;
 
 	do {
 		struct tb_cfg_request *req;
@@ -410,7 +410,7 @@
 		return -ENOMEM;
 
 	ret = icm_request(tb, &request, sizeof(request), switches,
-			  sizeof(*switches), npackets, ICM_TIMEOUT);
+			  sizeof(*switches), npackets, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		goto err_free;
 
@@ -463,7 +463,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -488,7 +488,7 @@
 	memset(&reply, 0, sizeof(reply));
 	/* Use larger timeout as establishing tunnels can take some time */
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_APPROVE_TIMEOUT);
+			  1, ICM_RETRIES, ICM_APPROVE_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -515,7 +515,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -543,7 +543,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -577,7 +577,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1022,7 +1022,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, 20000);
+			  1, 10, 2000);
 	if (ret)
 		return ret;
 
@@ -1055,7 +1055,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_APPROVE_TIMEOUT);
+			  1, ICM_RETRIES, ICM_APPROVE_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1083,7 +1083,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1112,7 +1112,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1146,7 +1146,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1172,7 +1172,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1498,7 +1498,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1524,7 +1524,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1545,7 +1545,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1606,7 +1606,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -1628,7 +1628,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, 20000);
+			  1, ICM_RETRIES, 20000);
 	if (ret)
 		return ret;
 
@@ -2295,7 +2295,7 @@
 
 	memset(&reply, 0, sizeof(reply));
 	ret = icm_request(tb, &request, sizeof(request), &reply, sizeof(reply),
-			  1, ICM_TIMEOUT);
+			  1, ICM_RETRIES, ICM_TIMEOUT);
 	if (ret)
 		return ret;
 
@@ -2511,6 +2511,11 @@
 	case PCI_DEVICE_ID_INTEL_TGL_H_NHI1:
 	case PCI_DEVICE_ID_INTEL_ADL_NHI0:
 	case PCI_DEVICE_ID_INTEL_ADL_NHI1:
+	case PCI_DEVICE_ID_INTEL_RPL_NHI0:
+	case PCI_DEVICE_ID_INTEL_RPL_NHI1:
+	case PCI_DEVICE_ID_INTEL_MTL_M_NHI0:
+	case PCI_DEVICE_ID_INTEL_MTL_P_NHI0:
+	case PCI_DEVICE_ID_INTEL_MTL_P_NHI1:
 		icm->is_supported = icm_tgl_is_supported;
 		icm->driver_ready = icm_icl_driver_ready;
 		icm->set_uuid = icm_icl_set_uuid;
@@ -2522,6 +2527,7 @@
 		tb->cm_ops = &icm_icl_ops;
 		break;
 
+	case PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_2C_NHI:
 	case PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_4C_NHI:
 		icm->is_supported = icm_tgl_is_supported;
 		icm->get_mode = icm_ar_get_mode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/nhi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/nhi.c
@@ -25,7 +25,11 @@
 #define RING_TYPE(ring) ((ring)->is_tx ? "TX ring" : "RX ring")
 
 #define RING_FIRST_USABLE_HOPID	1
-
+/*
+ * Used with QUIRK_E2E to specify an unused HopID the Rx credits are
+ * transferred.
+ */
+#define RING_E2E_RESERVED_HOPID	RING_FIRST_USABLE_HOPID
 /*
  * Minimal number of vectors when we use MSI-X. Two for control channel
  * Rx/Tx and the rest four are for cross domain DMA paths.
@@ -35,9 +39,11 @@
 
 #define NHI_MAILBOX_TIMEOUT	500 /* ms */
 
+/* Host interface quirks */
 #define QUIRK_AUTO_CLEAR_INT	BIT(0)
+#define QUIRK_E2E		BIT(1)
 
-static int ring_interrupt_index(struct tb_ring *ring)
+static int ring_interrupt_index(const struct tb_ring *ring)
 {
 	int bit = ring->hop;
 	if (!ring->is_tx)
@@ -45,6 +51,26 @@
 	return bit;
 }
 
+static void nhi_mask_interrupt(struct tb_nhi *nhi, int mask, int ring)
+{
+	if (nhi->quirks & QUIRK_AUTO_CLEAR_INT) {
+		u32 val;
+
+		val = ioread32(nhi->iobase + REG_RING_INTERRUPT_BASE + ring);
+		iowrite32(val & ~mask, nhi->iobase + REG_RING_INTERRUPT_BASE + ring);
+	} else {
+		iowrite32(mask, nhi->iobase + REG_RING_INTERRUPT_MASK_CLEAR_BASE + ring);
+	}
+}
+
+static void nhi_clear_interrupt(struct tb_nhi *nhi, int ring)
+{
+	if (nhi->quirks & QUIRK_AUTO_CLEAR_INT)
+		ioread32(nhi->iobase + REG_RING_NOTIFY_BASE + ring);
+	else
+		iowrite32(~0, nhi->iobase + REG_RING_INT_CLEAR + ring);
+}
+
 /*
  * ring_interrupt_active() - activate/deactivate interrupts for a single ring
  *
@@ -52,15 +78,16 @@
  */
 static void ring_interrupt_active(struct tb_ring *ring, bool active)
 {
-	int reg = REG_RING_INTERRUPT_BASE +
-		  ring_interrupt_index(ring) / 32 * 4;
-	int bit = ring_interrupt_index(ring) & 31;
-	int mask = 1 << bit;
+	int index = ring_interrupt_index(ring) / 32 * 4;
+	int reg = REG_RING_INTERRUPT_BASE + index;
+	int interrupt_bit = ring_interrupt_index(ring) & 31;
+	int mask = 1 << interrupt_bit;
 	u32 old, new;
 
 	if (ring->irq > 0) {
 		u32 step, shift, ivr, misc;
 		void __iomem *ivr_base;
+		int auto_clear_bit;
 		int index;
 
 		if (ring->is_tx)
@@ -68,18 +95,25 @@
 		else
 			index = ring->hop + ring->nhi->hop_count;
 
-		if (ring->nhi->quirks & QUIRK_AUTO_CLEAR_INT) {
-			/*
-			 * Ask the hardware to clear interrupt status
-			 * bits automatically since we already know
-			 * which interrupt was triggered.
-			 */
-			misc = ioread32(ring->nhi->iobase + REG_DMA_MISC);
-			if (!(misc & REG_DMA_MISC_INT_AUTO_CLEAR)) {
-				misc |= REG_DMA_MISC_INT_AUTO_CLEAR;
-				iowrite32(misc, ring->nhi->iobase + REG_DMA_MISC);
-			}
-		}
+		/*
+		 * Intel routers support a bit that isn't part of
+		 * the USB4 spec to ask the hardware to clear
+		 * interrupt status bits automatically since
+		 * we already know which interrupt was triggered.
+		 *
+		 * Other routers explicitly disable auto-clear
+		 * to prevent conditions that may occur where two
+		 * MSIX interrupts are simultaneously active and
+		 * reading the register clears both of them.
+		 */
+		misc = ioread32(ring->nhi->iobase + REG_DMA_MISC);
+		if (ring->nhi->quirks & QUIRK_AUTO_CLEAR_INT)
+			auto_clear_bit = REG_DMA_MISC_INT_AUTO_CLEAR;
+		else
+			auto_clear_bit = REG_DMA_MISC_DISABLE_AUTO_CLEAR;
+		if (!(misc & auto_clear_bit))
+			iowrite32(misc | auto_clear_bit,
+				  ring->nhi->iobase + REG_DMA_MISC);
 
 		ivr_base = ring->nhi->iobase + REG_INT_VEC_ALLOC_BASE;
 		step = index / REG_INT_VEC_ALLOC_REGS * REG_INT_VEC_ALLOC_BITS;
@@ -99,14 +133,18 @@
 
 	dev_dbg(&ring->nhi->pdev->dev,
 		"%s interrupt at register %#x bit %d (%#x -> %#x)\n",
-		active ? "enabling" : "disabling", reg, bit, old, new);
+		active ? "enabling" : "disabling", reg, interrupt_bit, old, new);
 
 	if (new == old)
 		dev_WARN(&ring->nhi->pdev->dev,
 					 "interrupt for %s %d is already %s\n",
 					 RING_TYPE(ring), ring->hop,
 					 active ? "enabled" : "disabled");
-	iowrite32(new, ring->nhi->iobase + reg);
+
+	if (active)
+		iowrite32(new, ring->nhi->iobase + reg);
+	else
+		nhi_mask_interrupt(ring->nhi, mask, index);
 }
 
 /*
@@ -119,11 +157,11 @@
 	int i = 0;
 	/* disable interrupts */
 	for (i = 0; i < RING_INTERRUPT_REG_COUNT(nhi); i++)
-		iowrite32(0, nhi->iobase + REG_RING_INTERRUPT_BASE + 4 * i);
+		nhi_mask_interrupt(nhi, ~0, 4 * i);
 
 	/* clear interrupt status bits */
 	for (i = 0; i < RING_NOTIFY_REG_COUNT(nhi); i++)
-		ioread32(nhi->iobase + REG_RING_NOTIFY_BASE + 4 * i);
+		nhi_clear_interrupt(nhi, 4 * i);
 }
 
 /* ring helper methods */
@@ -384,14 +422,17 @@
 
 static void ring_clear_msix(const struct tb_ring *ring)
 {
+	int bit;
+
 	if (ring->nhi->quirks & QUIRK_AUTO_CLEAR_INT)
 		return;
 
+	bit = ring_interrupt_index(ring) & 31;
 	if (ring->is_tx)
-		ioread32(ring->nhi->iobase + REG_RING_NOTIFY_BASE);
+		iowrite32(BIT(bit), ring->nhi->iobase + REG_RING_INT_CLEAR);
 	else
-		ioread32(ring->nhi->iobase + REG_RING_NOTIFY_BASE +
-			 4 * (ring->nhi->hop_count / 32));
+		iowrite32(BIT(bit), ring->nhi->iobase + REG_RING_INT_CLEAR +
+			  4 * (ring->nhi->hop_count / 32));
 }
 
 static irqreturn_t ring_msix(int irq, void *data)
@@ -455,8 +496,18 @@
 
 static int nhi_alloc_hop(struct tb_nhi *nhi, struct tb_ring *ring)
 {
+	unsigned int start_hop = RING_FIRST_USABLE_HOPID;
 	int ret = 0;
 
+	if (nhi->quirks & QUIRK_E2E) {
+		start_hop = RING_FIRST_USABLE_HOPID + 1;
+		if (ring->flags & RING_FLAG_E2E && !ring->is_tx) {
+			dev_dbg(&nhi->pdev->dev, "quirking E2E TX HopID %u -> %u\n",
+				ring->e2e_tx_hop, RING_E2E_RESERVED_HOPID);
+			ring->e2e_tx_hop = RING_E2E_RESERVED_HOPID;
+		}
+	}
+
 	spin_lock_irq(&nhi->lock);
 
 	if (ring->hop < 0) {
@@ -466,7 +517,7 @@
 		 * Automatically allocate HopID from the non-reserved
 		 * range 1 .. hop_count - 1.
 		 */
-		for (i = RING_FIRST_USABLE_HOPID; i < nhi->hop_count; i++) {
+		for (i = start_hop; i < nhi->hop_count; i++) {
 			if (ring->is_tx) {
 				if (!nhi->tx_rings[i]) {
 					ring->hop = i;
@@ -481,6 +532,11 @@
 		}
 	}
 
+	if (ring->hop > 0 && ring->hop < start_hop) {
+		dev_warn(&nhi->pdev->dev, "invalid hop: %d\n", ring->hop);
+		ret = -EINVAL;
+		goto err_unlock;
+	}
 	if (ring->hop < 0 || ring->hop >= nhi->hop_count) {
 		dev_warn(&nhi->pdev->dev, "invalid hop: %d\n", ring->hop);
 		ret = -EINVAL;
@@ -1094,12 +1150,26 @@
 
 static void nhi_check_quirks(struct tb_nhi *nhi)
 {
-	/*
-	 * Intel hardware supports auto clear of the interrupt status
-	 * reqister right after interrupt is being issued.
-	 */
-	if (nhi->pdev->vendor == PCI_VENDOR_ID_INTEL)
+	if (nhi->pdev->vendor == PCI_VENDOR_ID_INTEL) {
+		/*
+		 * Intel hardware supports auto clear of the interrupt
+		 * status register right after interrupt is being
+		 * issued.
+		 */
 		nhi->quirks |= QUIRK_AUTO_CLEAR_INT;
+
+		switch (nhi->pdev->device) {
+		case PCI_DEVICE_ID_INTEL_FALCON_RIDGE_2C_NHI:
+		case PCI_DEVICE_ID_INTEL_FALCON_RIDGE_4C_NHI:
+			/*
+			 * Falcon Ridge controller needs the end-to-end
+			 * flow control workaround to avoid losing Rx
+			 * packets when RING_FLAG_E2E is set.
+			 */
+			nhi->quirks |= QUIRK_E2E;
+			break;
+		}
+	}
 }
 
 static int nhi_init_msi(struct tb_nhi *nhi)
@@ -1367,6 +1437,30 @@
 	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ADL_NHI1),
 	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_RPL_NHI0),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_RPL_NHI1),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTL_M_NHI0),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTL_P_NHI0),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTL_P_NHI1),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_LNL_NHI0),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_LNL_NHI1),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_PTL_M_NHI0),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_PTL_M_NHI1),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_PTL_P_NHI0),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_PTL_P_NHI1),
+	  .driver_data = (kernel_ulong_t)&icl_nhi_ops },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_BARLOW_RIDGE_HOST_80G_NHI) },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_BARLOW_RIDGE_HOST_40G_NHI) },
 
 	/* Any USB4 compliant host */
 	{ PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_USB4, ~0) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/nhi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/nhi.h
@@ -55,6 +55,7 @@
  * need for the PCI quirk anymore as we will use ICM also on Apple
  * hardware.
  */
+#define PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_2C_NHI		0x1134
 #define PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_4C_NHI		0x1137
 #define PCI_DEVICE_ID_INTEL_WIN_RIDGE_2C_NHI            0x157d
 #define PCI_DEVICE_ID_INTEL_WIN_RIDGE_2C_BRIDGE         0x157e
@@ -74,12 +75,25 @@
 #define PCI_DEVICE_ID_INTEL_TITAN_RIDGE_DD_BRIDGE	0x15ef
 #define PCI_DEVICE_ID_INTEL_ADL_NHI0			0x463e
 #define PCI_DEVICE_ID_INTEL_ADL_NHI1			0x466d
+#define PCI_DEVICE_ID_INTEL_BARLOW_RIDGE_HOST_80G_NHI	0x5781
+#define PCI_DEVICE_ID_INTEL_BARLOW_RIDGE_HOST_40G_NHI	0x5784
+#define PCI_DEVICE_ID_INTEL_MTL_M_NHI0			0x7eb2
+#define PCI_DEVICE_ID_INTEL_MTL_P_NHI0			0x7ec2
+#define PCI_DEVICE_ID_INTEL_MTL_P_NHI1			0x7ec3
 #define PCI_DEVICE_ID_INTEL_ICL_NHI1			0x8a0d
 #define PCI_DEVICE_ID_INTEL_ICL_NHI0			0x8a17
 #define PCI_DEVICE_ID_INTEL_TGL_NHI0			0x9a1b
 #define PCI_DEVICE_ID_INTEL_TGL_NHI1			0x9a1d
 #define PCI_DEVICE_ID_INTEL_TGL_H_NHI0			0x9a1f
 #define PCI_DEVICE_ID_INTEL_TGL_H_NHI1			0x9a21
+#define PCI_DEVICE_ID_INTEL_RPL_NHI0			0xa73e
+#define PCI_DEVICE_ID_INTEL_RPL_NHI1			0xa76d
+#define PCI_DEVICE_ID_INTEL_LNL_NHI0			0xa833
+#define PCI_DEVICE_ID_INTEL_LNL_NHI1			0xa834
+#define PCI_DEVICE_ID_INTEL_PTL_M_NHI0			0xe333
+#define PCI_DEVICE_ID_INTEL_PTL_M_NHI1			0xe334
+#define PCI_DEVICE_ID_INTEL_PTL_P_NHI0			0xe433
+#define PCI_DEVICE_ID_INTEL_PTL_P_NHI1			0xe434
 
 #define PCI_CLASS_SERIAL_USB_USB4			0x0c0340
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/nhi_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/nhi_regs.h
@@ -77,12 +77,13 @@
 
 /*
  * three bitfields: tx, rx, rx overflow
- * Every bitfield contains one bit for every hop (REG_HOP_COUNT). Registers are
- * cleared on read. New interrupts are fired only after ALL registers have been
+ * Every bitfield contains one bit for every hop (REG_HOP_COUNT).
+ * New interrupts are fired only after ALL registers have been
  * read (even those containing only disabled rings).
  */
 #define REG_RING_NOTIFY_BASE	0x37800
 #define RING_NOTIFY_REG_COUNT(nhi) ((31 + 3 * nhi->hop_count) / 32)
+#define REG_RING_INT_CLEAR	0x37808
 
 /*
  * two bitfields: rx, tx
@@ -92,6 +93,8 @@
 #define REG_RING_INTERRUPT_BASE	0x38200
 #define RING_INTERRUPT_REG_COUNT(nhi) ((31 + 2 * nhi->hop_count) / 32)
 
+#define REG_RING_INTERRUPT_MASK_CLEAR_BASE	0x38208
+
 #define REG_INT_THROTTLING_RATE	0x38c00
 
 /* Interrupt Vector Allocation */
@@ -105,6 +108,7 @@
 
 #define REG_DMA_MISC			0x39864
 #define REG_DMA_MISC_INT_AUTO_CLEAR     BIT(2)
+#define REG_DMA_MISC_DISABLE_AUTO_CLEAR	BIT(17)
 
 #define REG_INMAIL_DATA			0x39900
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/path.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/path.c
@@ -85,11 +85,12 @@
  * @dst_hopid: HopID to the @dst (%-1 if don't care)
  * @last: Last port is filled here if not %NULL
  * @name: Name of the path
+ * @alloc_hopid: Allocate HopIDs for the ports
  *
  * Follows a path starting from @src and @src_hopid to the last output
- * port of the path. Allocates HopIDs for the visited ports. Call
- * tb_path_free() to release the path and allocated HopIDs when the path
- * is not needed anymore.
+ * port of the path. Allocates HopIDs for the visited ports (if
+ * @alloc_hopid is true). Call tb_path_free() to release the path and
+ * allocated HopIDs when the path is not needed anymore.
  *
  * Note function discovers also incomplete paths so caller should check
  * that the @dst port is the expected one. If it is not, the path can be
@@ -99,7 +100,8 @@
  */
 struct tb_path *tb_path_discover(struct tb_port *src, int src_hopid,
 				 struct tb_port *dst, int dst_hopid,
-				 struct tb_port **last, const char *name)
+				 struct tb_port **last, const char *name,
+				 bool alloc_hopid)
 {
 	struct tb_port *out_port;
 	struct tb_regs_hop hop;
@@ -156,6 +158,7 @@
 	path->tb = src->sw->tb;
 	path->path_length = num_hops;
 	path->activated = true;
+	path->alloc_hopid = alloc_hopid;
 
 	path->hops = kcalloc(num_hops, sizeof(*path->hops), GFP_KERNEL);
 	if (!path->hops) {
@@ -177,13 +180,14 @@
 			goto err;
 		}
 
-		if (tb_port_alloc_in_hopid(p, h, h) < 0)
+		if (alloc_hopid && tb_port_alloc_in_hopid(p, h, h) < 0)
 			goto err;
 
 		out_port = &sw->ports[hop.out_port];
 		next_hop = hop.next_hop;
 
-		if (tb_port_alloc_out_hopid(out_port, next_hop, next_hop) < 0) {
+		if (alloc_hopid &&
+		    tb_port_alloc_out_hopid(out_port, next_hop, next_hop) < 0) {
 			tb_port_release_in_hopid(p, h);
 			goto err;
 		}
@@ -263,6 +267,8 @@
 		return NULL;
 	}
 
+	path->alloc_hopid = true;
+
 	in_hopid = src_hopid;
 	out_port = NULL;
 
@@ -345,17 +351,19 @@
  */
 void tb_path_free(struct tb_path *path)
 {
-	int i;
+	if (path->alloc_hopid) {
+		int i;
 
-	for (i = 0; i < path->path_length; i++) {
-		const struct tb_path_hop *hop = &path->hops[i];
+		for (i = 0; i < path->path_length; i++) {
+			const struct tb_path_hop *hop = &path->hops[i];
 
-		if (hop->in_port)
-			tb_port_release_in_hopid(hop->in_port,
-						 hop->in_hop_index);
-		if (hop->out_port)
-			tb_port_release_out_hopid(hop->out_port,
-						  hop->next_hop_index);
+			if (hop->in_port)
+				tb_port_release_in_hopid(hop->in_port,
+							 hop->in_hop_index);
+			if (hop->out_port)
+				tb_port_release_out_hopid(hop->out_port,
+							  hop->next_hop_index);
+		}
 	}
 
 	kfree(path->hops);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/retimer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/retimer.c
@@ -208,6 +208,37 @@
 	return ret;
 }
 
+static void tb_retimer_nvm_authenticate_status(struct tb_port *port, u32 *status)
+{
+	int i;
+
+	tb_port_dbg(port, "reading NVM authentication status of retimers\n");
+
+	/*
+	 * Before doing anything else, read the authentication status.
+	 * If the retimer has it set, store it for the new retimer
+	 * device instance.
+	 */
+	for (i = 1; i <= TB_MAX_RETIMER_INDEX; i++)
+		usb4_port_retimer_nvm_authenticate_status(port, i, &status[i]);
+}
+
+static void tb_retimer_set_inbound_sbtx(struct tb_port *port)
+{
+	int i;
+
+	for (i = 1; i <= TB_MAX_RETIMER_INDEX; i++)
+		usb4_port_retimer_set_inbound_sbtx(port, i);
+}
+
+static void tb_retimer_unset_inbound_sbtx(struct tb_port *port)
+{
+	int i;
+
+	for (i = TB_MAX_RETIMER_INDEX; i >= 1; i--)
+		usb4_port_retimer_unset_inbound_sbtx(port, i);
+}
+
 static ssize_t nvm_authenticate_store(struct device *dev,
 	struct device_attribute *attr, const char *buf, size_t count)
 {
@@ -234,6 +265,7 @@
 	rt->auth_status = 0;
 
 	if (val) {
+		tb_retimer_set_inbound_sbtx(rt->port);
 		if (val == AUTHENTICATE_ONLY) {
 			ret = tb_retimer_nvm_authenticate(rt, true);
 		} else {
@@ -253,6 +285,7 @@
 	}
 
 exit_unlock:
+	tb_retimer_unset_inbound_sbtx(rt->port);
 	mutex_unlock(&rt->tb->lock);
 exit_rpm:
 	pm_runtime_mark_last_busy(&rt->dev);
@@ -324,15 +357,10 @@
 
 static int tb_retimer_add(struct tb_port *port, u8 index, u32 auth_status)
 {
-	struct usb4_port *usb4;
 	struct tb_retimer *rt;
 	u32 vendor, device;
 	int ret;
 
-	usb4 = port->usb4;
-	if (!usb4)
-		return -EINVAL;
-
 	ret = usb4_port_retimer_read(port, index, USB4_SB_VENDOR_ID, &vendor,
 				     sizeof(vendor));
 	if (ret) {
@@ -374,7 +402,7 @@
 	rt->port = port;
 	rt->tb = port->sw->tb;
 
-	rt->dev.parent = &usb4->dev;
+	rt->dev.parent = &port->usb4->dev;
 	rt->dev.bus = &tb_bus_type;
 	rt->dev.type = &tb_retimer_type;
 	dev_set_name(&rt->dev, "%s:%u.%u", dev_name(&port->sw->dev),
@@ -453,6 +481,13 @@
 {
 	u32 status[TB_MAX_RETIMER_INDEX + 1] = {};
 	int ret, i, last_idx = 0;
+	struct usb4_port *usb4;
+
+	usb4 = port->usb4;
+	if (!usb4)
+		return 0;
+
+	pm_runtime_get_sync(&usb4->dev);
 
 	/*
 	 * Send broadcast RT to make sure retimer indices facing this
@@ -460,22 +495,19 @@
 	 */
 	ret = usb4_port_enumerate_retimers(port);
 	if (ret)
-		return ret;
+		goto out;
 
 	/*
-	 * Enable sideband channel for each retimer. We can do this
-	 * regardless whether there is device connected or not.
+	 * Immediately after sending enumerate retimers read the
+	 * authentication status of each retimer.
 	 */
-	for (i = 1; i <= TB_MAX_RETIMER_INDEX; i++)
-		usb4_port_retimer_set_inbound_sbtx(port, i);
+	tb_retimer_nvm_authenticate_status(port, status);
 
 	/*
-	 * Before doing anything else, read the authentication status.
-	 * If the retimer has it set, store it for the new retimer
-	 * device instance.
+	 * Enable sideband channel for each retimer. We can do this
+	 * regardless whether there is device connected or not.
 	 */
-	for (i = 1; i <= TB_MAX_RETIMER_INDEX; i++)
-		usb4_port_retimer_nvm_authenticate_status(port, i, &status[i]);
+	tb_retimer_set_inbound_sbtx(port);
 
 	for (i = 1; i <= TB_MAX_RETIMER_INDEX; i++) {
 		/*
@@ -490,8 +522,12 @@
 			break;
 	}
 
-	if (!last_idx)
-		return 0;
+	tb_retimer_unset_inbound_sbtx(port);
+
+	if (!last_idx) {
+		ret = 0;
+		goto out;
+	}
 
 	/* Add on-board retimers if they do not exist already */
 	for (i = 1; i <= last_idx; i++) {
@@ -507,7 +543,11 @@
 		}
 	}
 
-	return 0;
+out:
+	pm_runtime_mark_last_busy(&usb4->dev);
+	pm_runtime_put_autosuspend(&usb4->dev);
+
+	return ret;
 }
 
 static int remove_retimer(struct device *dev, void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/sb_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/sb_regs.h
@@ -20,6 +20,7 @@
 	USB4_SB_OPCODE_ROUTER_OFFLINE = 0x4e45534c,		/* "LSEN" */
 	USB4_SB_OPCODE_ENUMERATE_RETIMERS = 0x4d554e45,		/* "ENUM" */
 	USB4_SB_OPCODE_SET_INBOUND_SBTX = 0x5055534c,		/* "LSUP" */
+	USB4_SB_OPCODE_UNSET_INBOUND_SBTX = 0x50555355,		/* "USUP" */
 	USB4_SB_OPCODE_QUERY_LAST_RETIMER = 0x5453414c,		/* "LAST" */
 	USB4_SB_OPCODE_GET_NVM_SECTOR_SIZE = 0x53534e47,	/* "GNSS" */
 	USB4_SB_OPCODE_NVM_SET_OFFSET = 0x53504f42,		/* "BOPS" */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/switch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/switch.c
@@ -623,6 +623,9 @@
 		return 0;
 
 	nfc_credits = port->config.nfc_credits & ADP_CS_4_NFC_BUFFERS_MASK;
+	if (credits < 0)
+		credits = max_t(int, -nfc_credits, credits);
+
 	nfc_credits += credits;
 
 	tb_port_dbg(port, "adding %d NFC credits to %lu", credits,
@@ -1319,7 +1322,9 @@
  * @aux_tx: AUX TX Hop ID
  * @aux_rx: AUX RX Hop ID
  *
- * Programs specified Hop IDs for DP IN/OUT port.
+ * Programs specified Hop IDs for DP IN/OUT port. Can be called for USB4
+ * router DP adapters too but does not program the values as the fields
+ * are read-only.
  */
 int tb_dp_port_set_hops(struct tb_port *port, unsigned int video,
 			unsigned int aux_tx, unsigned int aux_rx)
@@ -1327,6 +1332,9 @@
 	u32 data[2];
 	int ret;
 
+	if (tb_switch_is_usb4(port->sw))
+		return 0;
+
 	ret = tb_port_read(port, data, TB_CFG_PORT,
 			   port->cap_adap + ADP_DP_CS_0, ARRAY_SIZE(data));
 	if (ret)
@@ -2281,6 +2289,7 @@
 		 * additional capabilities.
 		 */
 		sw->config.cmuv = USB4_VERSION_1_0;
+		sw->config.plug_events_delay = 0xa;
 
 		/* Enumerate the switch */
 		ret = tb_sw_write(sw, (u32 *)&sw->config + 1, TB_CFG_SWITCH,
@@ -2551,6 +2560,13 @@
 	    !tb_port_is_width_supported(down, 2))
 		return 0;
 
+	/*
+	 * Both lanes need to be in CL0. Here we assume lane 0 already be in
+	 * CL0 and check just for lane 1.
+	 */
+	if (tb_wait_for_port(down->dual_link_port, false) <= 0)
+		return -ENOTCONN;
+
 	ret = tb_port_lane_bonding_enable(up);
 	if (ret) {
 		tb_port_warn(up, "failed to enable lane bonding\n");
@@ -2661,22 +2677,29 @@
 {
 	struct tb_port *up, *down;
 
-	if (sw->is_unplugged)
-		return;
 	if (!tb_route(sw) || tb_switch_is_icm(sw))
 		return;
 
+	/*
+	 * Unconfigure downstream port so that wake-on-connect can be
+	 * configured after router unplug. No need to unconfigure upstream port
+	 * since its router is unplugged.
+	 */
 	up = tb_upstream_port(sw);
-	if (tb_switch_is_usb4(up->sw))
-		usb4_port_unconfigure(up);
-	else
-		tb_lc_unconfigure_port(up);
-
 	down = up->remote;
 	if (tb_switch_is_usb4(down->sw))
 		usb4_port_unconfigure(down);
 	else
 		tb_lc_unconfigure_port(down);
+
+	if (sw->is_unplugged)
+		return;
+
+	up = tb_upstream_port(sw);
+	if (tb_switch_is_usb4(up->sw))
+		usb4_port_unconfigure(up);
+	else
+		tb_lc_unconfigure_port(up);
 }
 
 static void tb_switch_credits_init(struct tb_switch *sw)
@@ -2689,6 +2712,26 @@
 		tb_sw_info(sw, "failed to determine preferred buffer allocation, using defaults\n");
 }
 
+static int tb_switch_port_hotplug_enable(struct tb_switch *sw)
+{
+	struct tb_port *port;
+
+	if (tb_switch_is_icm(sw))
+		return 0;
+
+	tb_switch_for_each_port(sw, port) {
+		int res;
+
+		if (!port->cap_usb4)
+			continue;
+
+		res = usb4_port_hotplug_enable(port);
+		if (res)
+			return res;
+	}
+	return 0;
+}
+
 /**
  * tb_switch_add() - Add a switch to the domain
  * @sw: Switch to add
@@ -2723,14 +2766,10 @@
 
 		/* read drom */
 		ret = tb_drom_read(sw);
-		if (ret) {
-			dev_err(&sw->dev, "reading DROM failed\n");
-			return ret;
-		}
+		if (ret)
+			dev_warn(&sw->dev, "reading DROM failed: %d\n", ret);
 		tb_sw_dbg(sw, "uid: %#llx\n", sw->uid);
 
-		tb_check_quirks(sw);
-
 		ret = tb_switch_set_uuid(sw);
 		if (ret) {
 			dev_err(&sw->dev, "failed to set UUID\n");
@@ -2749,6 +2788,8 @@
 			}
 		}
 
+		tb_check_quirks(sw);
+
 		tb_switch_default_link_ports(sw);
 
 		ret = tb_switch_update_link_attributes(sw);
@@ -2760,6 +2801,10 @@
 			return ret;
 	}
 
+	ret = tb_switch_port_hotplug_enable(sw);
+	if (ret)
+		return ret;
+
 	ret = device_add(&sw->dev);
 	if (ret) {
 		dev_err(&sw->dev, "failed to add device: %d\n", ret);
@@ -2838,6 +2883,7 @@
 			tb_switch_remove(port->remote->sw);
 			port->remote = NULL;
 		} else if (port->xdomain) {
+			port->xdomain->is_unplugged = true;
 			tb_xdomain_remove(port->xdomain);
 			port->xdomain = NULL;
 		}
@@ -2894,7 +2940,26 @@
 	return tb_lc_set_wake(sw, flags);
 }
 
-int tb_switch_resume(struct tb_switch *sw)
+static void tb_switch_check_wakes(struct tb_switch *sw)
+{
+	if (device_may_wakeup(&sw->dev)) {
+		if (tb_switch_is_usb4(sw))
+			usb4_switch_check_wakes(sw);
+	}
+}
+
+/**
+ * tb_switch_resume() - Resume a switch after sleep
+ * @sw: Switch to resume
+ * @runtime: Is this resume from runtime suspend or system sleep
+ *
+ * Resumes and re-enumerates router (and all its children), if still plugged
+ * after suspend. Don't enumerate device router whose UID was changed during
+ * suspend. If this is resume from system sleep, notifies PM core about the
+ * wakes occurred during suspend. Disables all wakes, except USB4 wake of
+ * upstream port for USB4 routers that shall be always enabled.
+ */
+int tb_switch_resume(struct tb_switch *sw, bool runtime)
 {
 	struct tb_port *port;
 	int err;
@@ -2919,6 +2984,10 @@
 			return err;
 		}
 
+		/* We don't have any way to confirm this was the same device */
+		if (!sw->uid)
+			return -ENODEV;
+
 		if (tb_switch_is_usb4(sw))
 			err = usb4_switch_read_uid(sw, &uid);
 		else
@@ -2939,6 +3008,9 @@
 	if (err)
 		return err;
 
+	if (!runtime)
+		tb_switch_check_wakes(sw);
+
 	/* Disable wakes */
 	tb_switch_set_wake(sw, 0);
 
@@ -2968,7 +3040,8 @@
 			 */
 			if (tb_port_unlock(port))
 				tb_port_warn(port, "failed to unlock port\n");
-			if (port->remote && tb_switch_resume(port->remote->sw)) {
+			if (port->remote &&
+			    tb_switch_resume(port->remote->sw, runtime)) {
 				tb_port_warn(port,
 					     "lost during suspend, disconnecting\n");
 				tb_sw_set_unplugged(port->remote->sw);
@@ -3048,9 +3121,20 @@
  */
 int tb_switch_alloc_dp_resource(struct tb_switch *sw, struct tb_port *in)
 {
+	int ret;
+
 	if (tb_switch_is_usb4(sw))
-		return usb4_switch_alloc_dp_resource(sw, in);
-	return tb_lc_dp_sink_alloc(sw, in);
+		ret = usb4_switch_alloc_dp_resource(sw, in);
+	else
+		ret = tb_lc_dp_sink_alloc(sw, in);
+
+	if (ret)
+		tb_sw_warn(sw, "failed to allocate DP resource for port %d\n",
+			   in->port);
+	else
+		tb_sw_dbg(sw, "allocated DP resource for port %d\n", in->port);
+
+	return ret;
 }
 
 /**
@@ -3073,6 +3157,8 @@
 	if (ret)
 		tb_sw_warn(sw, "failed to de-allocate DP resource for port %d\n",
 			   in->port);
+	else
+		tb_sw_dbg(sw, "released DP resource for port %d\n", in->port);
 }
 
 struct tb_sw_lookup {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/tb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/tb.c
@@ -105,10 +105,37 @@
 	}
 }
 
-static void tb_discover_tunnels(struct tb_switch *sw)
+static void tb_discover_dp_resource(struct tb *tb, struct tb_port *port)
 {
-	struct tb *tb = sw->tb;
 	struct tb_cm *tcm = tb_priv(tb);
+	struct tb_port *p;
+
+	list_for_each_entry(p, &tcm->dp_resources, list) {
+		if (p == port)
+			return;
+	}
+
+	tb_port_dbg(port, "DP %s resource available discovered\n",
+		    tb_port_is_dpin(port) ? "IN" : "OUT");
+	list_add_tail(&port->list, &tcm->dp_resources);
+}
+
+static void tb_discover_dp_resources(struct tb *tb)
+{
+	struct tb_cm *tcm = tb_priv(tb);
+	struct tb_tunnel *tunnel;
+
+	list_for_each_entry(tunnel, &tcm->tunnel_list, list) {
+		if (tb_tunnel_is_dp(tunnel))
+			tb_discover_dp_resource(tb, tunnel->dst_port);
+	}
+}
+
+static void tb_switch_discover_tunnels(struct tb_switch *sw,
+				       struct list_head *list,
+				       bool alloc_hopids)
+{
+	struct tb *tb = sw->tb;
 	struct tb_port *port;
 
 	tb_switch_for_each_port(sw, port) {
@@ -116,24 +143,41 @@
 
 		switch (port->config.type) {
 		case TB_TYPE_DP_HDMI_IN:
-			tunnel = tb_tunnel_discover_dp(tb, port);
+			tunnel = tb_tunnel_discover_dp(tb, port, alloc_hopids);
 			break;
 
 		case TB_TYPE_PCIE_DOWN:
-			tunnel = tb_tunnel_discover_pci(tb, port);
+			tunnel = tb_tunnel_discover_pci(tb, port, alloc_hopids);
 			break;
 
 		case TB_TYPE_USB3_DOWN:
-			tunnel = tb_tunnel_discover_usb3(tb, port);
+			tunnel = tb_tunnel_discover_usb3(tb, port, alloc_hopids);
 			break;
 
 		default:
 			break;
 		}
 
-		if (!tunnel)
-			continue;
+		if (tunnel)
+			list_add_tail(&tunnel->list, list);
+	}
+
+	tb_switch_for_each_port(sw, port) {
+		if (tb_port_has_remote(port)) {
+			tb_switch_discover_tunnels(port->remote->sw, list,
+						   alloc_hopids);
+		}
+	}
+}
+
+static void tb_discover_tunnels(struct tb *tb)
+{
+	struct tb_cm *tcm = tb_priv(tb);
+	struct tb_tunnel *tunnel;
 
+	tb_switch_discover_tunnels(tb->root_switch, &tcm->tunnel_list, true);
+
+	list_for_each_entry(tunnel, &tcm->tunnel_list, list) {
 		if (tb_tunnel_is_pci(tunnel)) {
 			struct tb_switch *parent = tunnel->dst_port->sw;
 
@@ -146,13 +190,6 @@
 			pm_runtime_get_sync(&tunnel->src_port->sw->dev);
 			pm_runtime_get_sync(&tunnel->dst_port->sw->dev);
 		}
-
-		list_add_tail(&tunnel->list, &tcm->tunnel_list);
-	}
-
-	tb_switch_for_each_port(sw, port) {
-		if (tb_port_has_remote(port))
-			tb_discover_tunnels(port->remote->sw);
 	}
 }
 
@@ -851,7 +888,7 @@
 
 static void tb_tunnel_dp(struct tb *tb)
 {
-	int available_up, available_down, ret;
+	int available_up, available_down, ret, link_nr;
 	struct tb_cm *tcm = tb_priv(tb);
 	struct tb_port *port, *in, *out;
 	struct tb_tunnel *tunnel;
@@ -897,6 +934,20 @@
 	}
 
 	/*
+	 * This is only applicable to links that are not bonded (so
+	 * when Thunderbolt 1 hardware is involved somewhere in the
+	 * topology). For these try to share the DP bandwidth between
+	 * the two lanes.
+	 */
+	link_nr = 1;
+	list_for_each_entry(tunnel, &tcm->tunnel_list, list) {
+		if (tb_tunnel_is_dp(tunnel)) {
+			link_nr = 0;
+			break;
+		}
+	}
+
+	/*
 	 * DP stream needs the domain to be active so runtime resume
 	 * both ends of the tunnel.
 	 *
@@ -927,7 +978,8 @@
 	tb_dbg(tb, "available bandwidth for new DP tunnel %u/%u Mb/s\n",
 	       available_up, available_down);
 
-	tunnel = tb_tunnel_alloc_dp(tb, in, out, available_up, available_down);
+	tunnel = tb_tunnel_alloc_dp(tb, in, out, link_nr, available_up,
+				    available_down);
 	if (!tunnel) {
 		tb_port_dbg(out, "could not allocate DP tunnel\n");
 		goto err_reclaim;
@@ -1369,7 +1421,9 @@
 	/* Full scan to discover devices added before the driver was loaded. */
 	tb_scan_switch(tb->root_switch);
 	/* Find out tunnels created by the boot firmware */
-	tb_discover_tunnels(tb->root_switch);
+	tb_discover_tunnels(tb);
+	/* Add DP resources from the DP tunnels created by the boot firmware */
+	tb_discover_dp_resources(tb);
 	/*
 	 * If the boot firmware did not create USB 3.x tunnels create them
 	 * now for the whole topology.
@@ -1429,18 +1483,43 @@
 {
 	struct tb_cm *tcm = tb_priv(tb);
 	struct tb_tunnel *tunnel, *n;
+	unsigned int usb3_delay = 0;
+	LIST_HEAD(tunnels);
 
 	tb_dbg(tb, "resuming...\n");
 
 	/* remove any pci devices the firmware might have setup */
 	tb_switch_reset(tb->root_switch);
 
-	tb_switch_resume(tb->root_switch);
+	tb_switch_resume(tb->root_switch, false);
 	tb_free_invalid_tunnels(tb);
 	tb_free_unplugged_children(tb->root_switch);
 	tb_restore_children(tb->root_switch);
-	list_for_each_entry_safe(tunnel, n, &tcm->tunnel_list, list)
+
+	/*
+	 * If we get here from suspend to disk the boot firmware or the
+	 * restore kernel might have created tunnels of its own. Since
+	 * we cannot be sure they are usable for us we find and tear
+	 * them down.
+	 */
+	tb_switch_discover_tunnels(tb->root_switch, &tunnels, false);
+	list_for_each_entry_safe_reverse(tunnel, n, &tunnels, list) {
+		if (tb_tunnel_is_usb3(tunnel))
+			usb3_delay = 500;
+		tb_tunnel_deactivate(tunnel);
+		tb_tunnel_free(tunnel);
+	}
+
+	/* Re-create our tunnels now */
+	list_for_each_entry_safe(tunnel, n, &tcm->tunnel_list, list) {
+		/* USB3 requires delay before it can be re-activated */
+		if (tb_tunnel_is_usb3(tunnel)) {
+			msleep(usb3_delay);
+			/* Only need to do it once */
+			usb3_delay = 0;
+		}
 		tb_tunnel_restart(tunnel);
+	}
 	if (!list_empty(&tcm->tunnel_list)) {
 		/*
 		 * the pcie links need some time to get going.
@@ -1538,7 +1617,7 @@
 	struct tb_tunnel *tunnel, *n;
 
 	mutex_lock(&tb->lock);
-	tb_switch_resume(tb->root_switch);
+	tb_switch_resume(tb->root_switch, true);
 	tb_free_invalid_tunnels(tb);
 	tb_restore_children(tb->root_switch);
 	list_for_each_entry_safe(tunnel, n, &tcm->tunnel_list, list)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/tb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/tb.h
@@ -354,6 +354,7 @@
  *	      when deactivating this path
  * @hops: Path hops
  * @path_length: How many hops the path uses
+ * @alloc_hopid: Does this path consume port HopID
  *
  * A path consists of a number of hops (see &struct tb_path_hop). To
  * establish a PCIe tunnel two paths have to be created between the two
@@ -374,6 +375,7 @@
 	bool clear_fc;
 	struct tb_path_hop *hops;
 	int path_length;
+	bool alloc_hopid;
 };
 
 /* HopIDs 0-7 are reserved by the Thunderbolt protocol */
@@ -738,7 +740,7 @@
 int tb_switch_add(struct tb_switch *sw);
 void tb_switch_remove(struct tb_switch *sw);
 void tb_switch_suspend(struct tb_switch *sw, bool runtime);
-int tb_switch_resume(struct tb_switch *sw);
+int tb_switch_resume(struct tb_switch *sw, bool runtime);
 int tb_switch_reset(struct tb_switch *sw);
 void tb_sw_set_unplugged(struct tb_switch *sw);
 struct tb_port *tb_switch_find_port(struct tb_switch *sw,
@@ -957,7 +959,8 @@
 
 struct tb_path *tb_path_discover(struct tb_port *src, int src_hopid,
 				 struct tb_port *dst, int dst_hopid,
-				 struct tb_port **last, const char *name);
+				 struct tb_port **last, const char *name,
+				 bool alloc_hopid);
 struct tb_path *tb_path_alloc(struct tb *tb, struct tb_port *src, int src_hopid,
 			      struct tb_port *dst, int dst_hopid, int link_nr,
 			      const char *name);
@@ -1040,6 +1043,7 @@
 	return NULL;
 }
 
+void usb4_switch_check_wakes(struct tb_switch *sw);
 int usb4_switch_setup(struct tb_switch *sw);
 int usb4_switch_read_uid(struct tb_switch *sw, u64 *uid);
 int usb4_switch_drom_read(struct tb_switch *sw, unsigned int address, void *buf,
@@ -1067,6 +1071,7 @@
 void usb4_switch_remove_ports(struct tb_switch *sw);
 
 int usb4_port_unlock(struct tb_port *port);
+int usb4_port_hotplug_enable(struct tb_port *port);
 int usb4_port_configure(struct tb_port *port);
 void usb4_port_unconfigure(struct tb_port *port);
 int usb4_port_configure_xdomain(struct tb_port *port);
@@ -1076,6 +1081,7 @@
 int usb4_port_enumerate_retimers(struct tb_port *port);
 
 int usb4_port_retimer_set_inbound_sbtx(struct tb_port *port, u8 index);
+int usb4_port_retimer_unset_inbound_sbtx(struct tb_port *port, u8 index);
 int usb4_port_retimer_read(struct tb_port *port, u8 index, u8 reg, void *buf,
 			   u8 size);
 int usb4_port_retimer_write(struct tb_port *port, u8 index, u8 reg,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/tb_regs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/tb_regs.h
@@ -301,6 +301,7 @@
 #define ADP_CS_5				0x05
 #define ADP_CS_5_LCA_MASK			GENMASK(28, 22)
 #define ADP_CS_5_LCA_SHIFT			22
+#define ADP_CS_5_DHP				BIT(31)
 
 /* TMU adapter registers */
 #define TMU_ADP_CS_3				0x03
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/test.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/test.c
@@ -1348,7 +1348,7 @@
 	in = &host->ports[5];
 	out = &dev->ports[13];
 
-	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, tunnel != NULL);
 	KUNIT_EXPECT_EQ(test, tunnel->type, TB_TUNNEL_DP);
 	KUNIT_EXPECT_PTR_EQ(test, tunnel->src_port, in);
@@ -1394,7 +1394,7 @@
 	in = &host->ports[5];
 	out = &dev4->ports[14];
 
-	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, tunnel != NULL);
 	KUNIT_EXPECT_EQ(test, tunnel->type, TB_TUNNEL_DP);
 	KUNIT_EXPECT_PTR_EQ(test, tunnel->src_port, in);
@@ -1444,7 +1444,7 @@
 	in = &dev2->ports[13];
 	out = &dev5->ports[13];
 
-	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, tunnel != NULL);
 	KUNIT_EXPECT_EQ(test, tunnel->type, TB_TUNNEL_DP);
 	KUNIT_EXPECT_PTR_EQ(test, tunnel->src_port, in);
@@ -1509,7 +1509,7 @@
 	in = &dev6->ports[13];
 	out = &dev12->ports[13];
 
-	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, tunnel != NULL);
 	KUNIT_EXPECT_EQ(test, tunnel->type, TB_TUNNEL_DP);
 	KUNIT_EXPECT_PTR_EQ(test, tunnel->src_port, in);
@@ -1627,7 +1627,7 @@
 	in = &dev2->ports[13];
 	out = &dev5->ports[13];
 
-	dp_tunnel = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	dp_tunnel = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, dp_tunnel != NULL);
 
 	KUNIT_EXPECT_TRUE(test, tb_tunnel_port_on_path(dp_tunnel, in));
@@ -2009,7 +2009,7 @@
 	in = &host->ports[5];
 	out = &dev->ports[14];
 
-	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	tunnel = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, tunnel != NULL);
 	KUNIT_ASSERT_EQ(test, tunnel->npaths, (size_t)3);
 
@@ -2245,7 +2245,7 @@
 
 	in = &host->ports[5];
 	out = &dev->ports[13];
-	dp_tunnel1 = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	dp_tunnel1 = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, dp_tunnel1 != NULL);
 	KUNIT_ASSERT_EQ(test, dp_tunnel1->npaths, (size_t)3);
 
@@ -2282,7 +2282,7 @@
 
 	in = &host->ports[6];
 	out = &dev->ports[14];
-	dp_tunnel2 = tb_tunnel_alloc_dp(NULL, in, out, 0, 0);
+	dp_tunnel2 = tb_tunnel_alloc_dp(NULL, in, out, 1, 0, 0);
 	KUNIT_ASSERT_TRUE(test, dp_tunnel2 != NULL);
 	KUNIT_ASSERT_EQ(test, dp_tunnel2->npaths, (size_t)3);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/tunnel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/tunnel.c
@@ -207,12 +207,14 @@
  * tb_tunnel_discover_pci() - Discover existing PCIe tunnels
  * @tb: Pointer to the domain structure
  * @down: PCIe downstream adapter
+ * @alloc_hopid: Allocate HopIDs from visited ports
  *
  * If @down adapter is active, follows the tunnel to the PCIe upstream
  * adapter and back. Returns the discovered tunnel or %NULL if there was
  * no tunnel.
  */
-struct tb_tunnel *tb_tunnel_discover_pci(struct tb *tb, struct tb_port *down)
+struct tb_tunnel *tb_tunnel_discover_pci(struct tb *tb, struct tb_port *down,
+					 bool alloc_hopid)
 {
 	struct tb_tunnel *tunnel;
 	struct tb_path *path;
@@ -233,7 +235,7 @@
 	 * case.
 	 */
 	path = tb_path_discover(down, TB_PCI_HOPID, NULL, -1,
-				&tunnel->dst_port, "PCIe Up");
+				&tunnel->dst_port, "PCIe Up", alloc_hopid);
 	if (!path) {
 		/* Just disable the downstream port */
 		tb_pci_port_enable(down, false);
@@ -244,7 +246,7 @@
 		goto err_free;
 
 	path = tb_path_discover(tunnel->dst_port, -1, down, TB_PCI_HOPID, NULL,
-				"PCIe Down");
+				"PCIe Down", alloc_hopid);
 	if (!path)
 		goto err_deactivate;
 	tunnel->paths[TB_PCI_PATH_DOWN] = path;
@@ -761,6 +763,7 @@
  * tb_tunnel_discover_dp() - Discover existing Display Port tunnels
  * @tb: Pointer to the domain structure
  * @in: DP in adapter
+ * @alloc_hopid: Allocate HopIDs from visited ports
  *
  * If @in adapter is active, follows the tunnel to the DP out adapter
  * and back. Returns the discovered tunnel or %NULL if there was no
@@ -768,7 +771,8 @@
  *
  * Return: DP tunnel or %NULL if no tunnel found.
  */
-struct tb_tunnel *tb_tunnel_discover_dp(struct tb *tb, struct tb_port *in)
+struct tb_tunnel *tb_tunnel_discover_dp(struct tb *tb, struct tb_port *in,
+					bool alloc_hopid)
 {
 	struct tb_tunnel *tunnel;
 	struct tb_port *port;
@@ -787,7 +791,7 @@
 	tunnel->src_port = in;
 
 	path = tb_path_discover(in, TB_DP_VIDEO_HOPID, NULL, -1,
-				&tunnel->dst_port, "Video");
+				&tunnel->dst_port, "Video", alloc_hopid);
 	if (!path) {
 		/* Just disable the DP IN port */
 		tb_dp_port_enable(in, false);
@@ -797,14 +801,15 @@
 	if (tb_dp_init_video_path(tunnel->paths[TB_DP_VIDEO_PATH_OUT]))
 		goto err_free;
 
-	path = tb_path_discover(in, TB_DP_AUX_TX_HOPID, NULL, -1, NULL, "AUX TX");
+	path = tb_path_discover(in, TB_DP_AUX_TX_HOPID, NULL, -1, NULL, "AUX TX",
+				alloc_hopid);
 	if (!path)
 		goto err_deactivate;
 	tunnel->paths[TB_DP_AUX_PATH_OUT] = path;
 	tb_dp_init_aux_path(tunnel->paths[TB_DP_AUX_PATH_OUT]);
 
 	path = tb_path_discover(tunnel->dst_port, -1, in, TB_DP_AUX_RX_HOPID,
-				&port, "AUX RX");
+				&port, "AUX RX", alloc_hopid);
 	if (!path)
 		goto err_deactivate;
 	tunnel->paths[TB_DP_AUX_PATH_IN] = path;
@@ -843,6 +848,7 @@
  * @tb: Pointer to the domain structure
  * @in: DP in adapter port
  * @out: DP out adapter port
+ * @link_nr: Preferred lane adapter when the link is not bonded
  * @max_up: Maximum available upstream bandwidth for the DP tunnel (%0
  *	    if not limited)
  * @max_down: Maximum available downstream bandwidth for the DP tunnel
@@ -854,8 +860,8 @@
  * Return: Returns a tb_tunnel on success or NULL on failure.
  */
 struct tb_tunnel *tb_tunnel_alloc_dp(struct tb *tb, struct tb_port *in,
-				     struct tb_port *out, int max_up,
-				     int max_down)
+				     struct tb_port *out, int link_nr,
+				     int max_up, int max_down)
 {
 	struct tb_tunnel *tunnel;
 	struct tb_path **paths;
@@ -879,21 +885,21 @@
 	paths = tunnel->paths;
 
 	path = tb_path_alloc(tb, in, TB_DP_VIDEO_HOPID, out, TB_DP_VIDEO_HOPID,
-			     1, "Video");
+			     link_nr, "Video");
 	if (!path)
 		goto err_free;
 	tb_dp_init_video_path(path);
 	paths[TB_DP_VIDEO_PATH_OUT] = path;
 
 	path = tb_path_alloc(tb, in, TB_DP_AUX_TX_HOPID, out,
-			     TB_DP_AUX_TX_HOPID, 1, "AUX TX");
+			     TB_DP_AUX_TX_HOPID, link_nr, "AUX TX");
 	if (!path)
 		goto err_free;
 	tb_dp_init_aux_path(path);
 	paths[TB_DP_AUX_PATH_OUT] = path;
 
 	path = tb_path_alloc(tb, out, TB_DP_AUX_RX_HOPID, in,
-			     TB_DP_AUX_RX_HOPID, 1, "AUX RX");
+			     TB_DP_AUX_RX_HOPID, link_nr, "AUX RX");
 	if (!path)
 		goto err_free;
 	tb_dp_init_aux_path(path);
@@ -1256,7 +1262,7 @@
 		return;
 	} else if (!ret) {
 		/* Use maximum link rate if the link valid is not set */
-		ret = usb4_usb3_port_max_link_rate(tunnel->src_port);
+		ret = tb_usb3_max_link_rate(tunnel->dst_port, tunnel->src_port);
 		if (ret < 0) {
 			tb_tunnel_warn(tunnel, "failed to read maximum link rate\n");
 			return;
@@ -1343,12 +1349,14 @@
  * tb_tunnel_discover_usb3() - Discover existing USB3 tunnels
  * @tb: Pointer to the domain structure
  * @down: USB3 downstream adapter
+ * @alloc_hopid: Allocate HopIDs from visited ports
  *
  * If @down adapter is active, follows the tunnel to the USB3 upstream
  * adapter and back. Returns the discovered tunnel or %NULL if there was
  * no tunnel.
  */
-struct tb_tunnel *tb_tunnel_discover_usb3(struct tb *tb, struct tb_port *down)
+struct tb_tunnel *tb_tunnel_discover_usb3(struct tb *tb, struct tb_port *down,
+					  bool alloc_hopid)
 {
 	struct tb_tunnel *tunnel;
 	struct tb_path *path;
@@ -1369,7 +1377,7 @@
 	 * case.
 	 */
 	path = tb_path_discover(down, TB_USB3_HOPID, NULL, -1,
-				&tunnel->dst_port, "USB3 Down");
+				&tunnel->dst_port, "USB3 Down", alloc_hopid);
 	if (!path) {
 		/* Just disable the downstream port */
 		tb_usb3_port_enable(down, false);
@@ -1379,7 +1387,7 @@
 	tb_usb3_init_path(tunnel->paths[TB_USB3_PATH_DOWN]);
 
 	path = tb_path_discover(tunnel->dst_port, -1, down, TB_USB3_HOPID, NULL,
-				"USB3 Up");
+				"USB3 Up", alloc_hopid);
 	if (!path)
 		goto err_deactivate;
 	tunnel->paths[TB_USB3_PATH_UP] = path;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/tunnel.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/tunnel.h
@@ -64,20 +64,23 @@
 	int allocated_down;
 };
 
-struct tb_tunnel *tb_tunnel_discover_pci(struct tb *tb, struct tb_port *down);
+struct tb_tunnel *tb_tunnel_discover_pci(struct tb *tb, struct tb_port *down,
+					 bool alloc_hopid);
 struct tb_tunnel *tb_tunnel_alloc_pci(struct tb *tb, struct tb_port *up,
 				      struct tb_port *down);
-struct tb_tunnel *tb_tunnel_discover_dp(struct tb *tb, struct tb_port *in);
+struct tb_tunnel *tb_tunnel_discover_dp(struct tb *tb, struct tb_port *in,
+					bool alloc_hopid);
 struct tb_tunnel *tb_tunnel_alloc_dp(struct tb *tb, struct tb_port *in,
-				     struct tb_port *out, int max_up,
-				     int max_down);
+				     struct tb_port *out, int link_nr,
+				     int max_up, int max_down);
 struct tb_tunnel *tb_tunnel_alloc_dma(struct tb *tb, struct tb_port *nhi,
 				      struct tb_port *dst, int transmit_path,
 				      int transmit_ring, int receive_path,
 				      int receive_ring);
 bool tb_tunnel_match_dma(const struct tb_tunnel *tunnel, int transmit_path,
 			 int transmit_ring, int receive_path, int receive_ring);
-struct tb_tunnel *tb_tunnel_discover_usb3(struct tb *tb, struct tb_port *down);
+struct tb_tunnel *tb_tunnel_discover_usb3(struct tb *tb, struct tb_port *down,
+					  bool alloc_hopid);
 struct tb_tunnel *tb_tunnel_alloc_usb3(struct tb *tb, struct tb_port *up,
 				       struct tb_port *down, int max_up,
 				       int max_down);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/thunderbolt/usb4.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/thunderbolt/usb4.c
@@ -175,15 +175,18 @@
 				tx_dwords, rx_data, rx_dwords);
 }
 
-static void usb4_switch_check_wakes(struct tb_switch *sw)
+/**
+ * usb4_switch_check_wakes() - Check for wakes and notify PM core about them
+ * @sw: Router whose wakes to check
+ *
+ * Checks wakes occurred during suspend and notify the PM core about them.
+ */
+void usb4_switch_check_wakes(struct tb_switch *sw)
 {
 	struct tb_port *port;
 	bool wakeup = false;
 	u32 val;
 
-	if (!device_may_wakeup(&sw->dev))
-		return;
-
 	if (tb_route(sw)) {
 		if (tb_sw_read(sw, &val, TB_CFG_SWITCH, ROUTER_CS_6, 1))
 			return;
@@ -248,8 +251,6 @@
 	u32 val = 0;
 	int ret;
 
-	usb4_switch_check_wakes(sw);
-
 	if (!tb_route(sw))
 		return 0;
 
@@ -1068,6 +1069,26 @@
 	return tb_port_write(port, &val, TB_CFG_PORT, ADP_CS_4, 1);
 }
 
+/**
+ * usb4_port_hotplug_enable() - Enables hotplug for a port
+ * @port: USB4 port to operate on
+ *
+ * Enables hot plug events on a given port. This is only intended
+ * to be used on lane, DP-IN, and DP-OUT adapters.
+ */
+int usb4_port_hotplug_enable(struct tb_port *port)
+{
+	int ret;
+	u32 val;
+
+	ret = tb_port_read(port, &val, TB_CFG_PORT, ADP_CS_5, 1);
+	if (ret)
+		return ret;
+
+	val &= ~ADP_CS_5_DHP;
+	return tb_port_write(port, &val, TB_CFG_PORT, ADP_CS_5, 1);
+}
+
 static int usb4_port_set_configured(struct tb_port *port, bool configured)
 {
 	int ret;
@@ -1422,6 +1443,20 @@
 }
 
 /**
+ * usb4_port_retimer_unset_inbound_sbtx() - Disable sideband channel transactions
+ * @port: USB4 port
+ * @index: Retimer index
+ *
+ * Disables sideband channel transations on SBTX. The reverse of
+ * usb4_port_retimer_set_inbound_sbtx().
+ */
+int usb4_port_retimer_unset_inbound_sbtx(struct tb_port *port, u8 index)
+{
+	return usb4_port_retimer_op(port, index,
+				    USB4_SB_OPCODE_UNSET_INBOUND_SBTX, 500);
+}
+
+/**
  * usb4_port_retimer_read() - Read from retimer sideband registers
  * @port: USB4 port
  * @index: Retimer index
@@ -1910,18 +1945,30 @@
 						    int downstream_bw)
 {
 	u32 val, ubw, dbw, scale;
-	int ret;
+	int ret, max_bw;
 
-	/* Read the used scale, hardware default is 0 */
-	ret = tb_port_read(port, &scale, TB_CFG_PORT,
-			   port->cap_adap + ADP_USB3_CS_3, 1);
+	/* Figure out suitable scale */
+	scale = 0;
+	max_bw = max(upstream_bw, downstream_bw);
+	while (scale < 64) {
+		if (mbps_to_usb3_bw(max_bw, scale) < 4096)
+			break;
+		scale++;
+	}
+
+	if (WARN_ON(scale >= 64))
+		return -EINVAL;
+
+	ret = tb_port_write(port, &scale, TB_CFG_PORT,
+			    port->cap_adap + ADP_USB3_CS_3, 1);
 	if (ret)
 		return ret;
 
-	scale &= ADP_USB3_CS_3_SCALE_MASK;
 	ubw = mbps_to_usb3_bw(upstream_bw, scale);
 	dbw = mbps_to_usb3_bw(downstream_bw, scale);
 
+	tb_port_dbg(port, "scaled bandwidth %u/%u, scale %u\n", ubw, dbw, scale);
+
 	ret = tb_port_read(port, &val, TB_CFG_PORT,
 			   port->cap_adap + ADP_USB3_CS_2, 1);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/goldfish.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/goldfish.c
@@ -61,13 +61,13 @@
 	spin_lock_irqsave(&qtty->lock, irq_flags);
 	gf_write_ptr((void *)address, base + GOLDFISH_TTY_REG_DATA_PTR,
 		     base + GOLDFISH_TTY_REG_DATA_PTR_HIGH);
-	__raw_writel(count, base + GOLDFISH_TTY_REG_DATA_LEN);
+	gf_iowrite32(count, base + GOLDFISH_TTY_REG_DATA_LEN);
 
 	if (is_write)
-		__raw_writel(GOLDFISH_TTY_CMD_WRITE_BUFFER,
+		gf_iowrite32(GOLDFISH_TTY_CMD_WRITE_BUFFER,
 		       base + GOLDFISH_TTY_REG_CMD);
 	else
-		__raw_writel(GOLDFISH_TTY_CMD_READ_BUFFER,
+		gf_iowrite32(GOLDFISH_TTY_CMD_READ_BUFFER,
 		       base + GOLDFISH_TTY_REG_CMD);
 
 	spin_unlock_irqrestore(&qtty->lock, irq_flags);
@@ -142,7 +142,7 @@
 	unsigned char *buf;
 	u32 count;
 
-	count = __raw_readl(base + GOLDFISH_TTY_REG_BYTES_READY);
+	count = gf_ioread32(base + GOLDFISH_TTY_REG_BYTES_READY);
 	if (count == 0)
 		return IRQ_NONE;
 
@@ -151,7 +151,7 @@
 	address = (unsigned long)(void *)buf;
 	goldfish_tty_rw(qtty, address, count, 0);
 
-	tty_schedule_flip(&qtty->port);
+	tty_flip_buffer_push(&qtty->port);
 	return IRQ_HANDLED;
 }
 
@@ -159,7 +159,7 @@
 {
 	struct goldfish_tty *qtty = container_of(port, struct goldfish_tty,
 									port);
-	__raw_writel(GOLDFISH_TTY_CMD_INT_ENABLE, qtty->base + GOLDFISH_TTY_REG_CMD);
+	gf_iowrite32(GOLDFISH_TTY_CMD_INT_ENABLE, qtty->base + GOLDFISH_TTY_REG_CMD);
 	return 0;
 }
 
@@ -167,7 +167,7 @@
 {
 	struct goldfish_tty *qtty = container_of(port, struct goldfish_tty,
 									port);
-	__raw_writel(GOLDFISH_TTY_CMD_INT_DISABLE, qtty->base + GOLDFISH_TTY_REG_CMD);
+	gf_iowrite32(GOLDFISH_TTY_CMD_INT_DISABLE, qtty->base + GOLDFISH_TTY_REG_CMD);
 }
 
 static int goldfish_tty_open(struct tty_struct *tty, struct file *filp)
@@ -202,7 +202,7 @@
 {
 	struct goldfish_tty *qtty = &goldfish_ttys[tty->index];
 	void __iomem *base = qtty->base;
-	return __raw_readl(base + GOLDFISH_TTY_REG_BYTES_READY);
+	return gf_ioread32(base + GOLDFISH_TTY_REG_BYTES_READY);
 }
 
 static void goldfish_tty_console_write(struct console *co, const char *b,
@@ -357,7 +357,7 @@
 	 * on Ranchu emulator (qemu2) returns 1 here and
 	 * driver will use physical addresses.
 	 */
-	qtty->version = __raw_readl(base + GOLDFISH_TTY_REG_VERSION);
+	qtty->version = gf_ioread32(base + GOLDFISH_TTY_REG_VERSION);
 
 	/*
 	 * Goldfish TTY device on Ranchu emulator (qemu2)
@@ -376,7 +376,7 @@
 		}
 	}
 
-	__raw_writel(GOLDFISH_TTY_CMD_INT_DISABLE, base + GOLDFISH_TTY_REG_CMD);
+	gf_iowrite32(GOLDFISH_TTY_CMD_INT_DISABLE, base + GOLDFISH_TTY_REG_CMD);
 
 	ret = request_irq(irq, goldfish_tty_interrupt, IRQF_SHARED,
 			  "goldfish_tty", qtty);
@@ -407,6 +407,7 @@
 err_tty_register_device_failed:
 	free_irq(irq, qtty);
 err_dec_line_count:
+	tty_port_destroy(&qtty->port);
 	goldfish_tty_current_line_count--;
 	if (goldfish_tty_current_line_count == 0)
 		goldfish_tty_delete_driver();
@@ -427,7 +428,8 @@
 	tty_unregister_device(goldfish_tty_driver, qtty->console.index);
 	iounmap(qtty->base);
 	qtty->base = NULL;
-	free_irq(qtty->irq, pdev);
+	free_irq(qtty->irq, qtty);
+	tty_port_destroy(&qtty->port);
 	goldfish_tty_current_line_count--;
 	if (goldfish_tty_current_line_count == 0)
 		goldfish_tty_delete_driver();
@@ -438,7 +440,7 @@
 #ifdef CONFIG_GOLDFISH_TTY_EARLY_CONSOLE
 static void gf_early_console_putchar(struct uart_port *port, int ch)
 {
-	__raw_writel(ch, port->membase);
+	gf_iowrite32(ch, port->membase);
 }
 
 static void gf_early_write(struct console *con, const char *s, unsigned int n)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/hvc/hvc_iucv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/hvc/hvc_iucv.c
@@ -1417,7 +1417,9 @@
  */
 static	int __init hvc_iucv_config(char *val)
 {
-	 return kstrtoul(val, 10, &hvc_iucv_devices);
+	if (kstrtoul(val, 10, &hvc_iucv_devices))
+		pr_warn("hvc_iucv= invalid parameter value '%s'\n", val);
+	return 1;
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/hvc/hvc_xen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/hvc/hvc_xen.c
@@ -37,10 +37,13 @@
 	struct xenbus_device *xbdev;
 	struct xencons_interface *intf;
 	unsigned int evtchn;
+	XENCONS_RING_IDX out_cons;
+	unsigned int out_cons_same;
 	struct hvc_struct *hvc;
 	int irq;
 	int vtermno;
 	grant_ref_t gntref;
+	spinlock_t ring_lock;
 };
 
 static LIST_HEAD(xenconsoles);
@@ -50,17 +53,22 @@
 
 static struct xencons_info *vtermno_to_xencons(int vtermno)
 {
-	struct xencons_info *entry, *n, *ret = NULL;
+	struct xencons_info *entry, *ret = NULL;
+	unsigned long flags;
 
-	if (list_empty(&xenconsoles))
-			return NULL;
+	spin_lock_irqsave(&xencons_lock, flags);
+	if (list_empty(&xenconsoles)) {
+		spin_unlock_irqrestore(&xencons_lock, flags);
+		return NULL;
+	}
 
-	list_for_each_entry_safe(entry, n, &xenconsoles, list) {
+	list_for_each_entry(entry, &xenconsoles, list) {
 		if (entry->vtermno == vtermno) {
 			ret  = entry;
 			break;
 		}
 	}
+	spin_unlock_irqrestore(&xencons_lock, flags);
 
 	return ret;
 }
@@ -82,12 +90,15 @@
 	XENCONS_RING_IDX cons, prod;
 	struct xencons_interface *intf = xencons->intf;
 	int sent = 0;
+	unsigned long flags;
 
+	spin_lock_irqsave(&xencons->ring_lock, flags);
 	cons = intf->out_cons;
 	prod = intf->out_prod;
 	mb();			/* update queue values before going on */
 
 	if ((prod - cons) > sizeof(intf->out)) {
+		spin_unlock_irqrestore(&xencons->ring_lock, flags);
 		pr_err_once("xencons: Illegal ring page indices");
 		return -EINVAL;
 	}
@@ -97,6 +108,7 @@
 
 	wmb();			/* write ring before updating pointer */
 	intf->out_prod = prod;
+	spin_unlock_irqrestore(&xencons->ring_lock, flags);
 
 	if (sent)
 		notify_daemon(xencons);
@@ -138,15 +150,20 @@
 	XENCONS_RING_IDX cons, prod;
 	int recv = 0;
 	struct xencons_info *xencons = vtermno_to_xencons(vtermno);
+	unsigned int eoiflag = 0;
+	unsigned long flags;
+
 	if (xencons == NULL)
 		return -EINVAL;
 	intf = xencons->intf;
 
+	spin_lock_irqsave(&xencons->ring_lock, flags);
 	cons = intf->in_cons;
 	prod = intf->in_prod;
 	mb();			/* get pointers before reading ring */
 
 	if ((prod - cons) > sizeof(intf->in)) {
+		spin_unlock_irqrestore(&xencons->ring_lock, flags);
 		pr_err_once("xencons: Illegal ring page indices");
 		return -EINVAL;
 	}
@@ -157,7 +174,30 @@
 	mb();			/* read ring before consuming */
 	intf->in_cons = cons;
 
-	notify_daemon(xencons);
+	/*
+	 * When to mark interrupt having been spurious:
+	 * - there was no new data to be read, and
+	 * - the backend did not consume some output bytes, and
+	 * - the previous round with no read data didn't see consumed bytes
+	 *   (we might have a race with an interrupt being in flight while
+	 *   updating xencons->out_cons, so account for that by allowing one
+	 *   round without any visible reason)
+	 */
+	if (intf->out_cons != xencons->out_cons) {
+		xencons->out_cons = intf->out_cons;
+		xencons->out_cons_same = 0;
+	}
+	if (!recv && xencons->out_cons_same++ > 1) {
+		eoiflag = XEN_EOI_FLAG_SPURIOUS;
+	}
+	spin_unlock_irqrestore(&xencons->ring_lock, flags);
+
+	if (recv) {
+		notify_daemon(xencons);
+	}
+
+	xen_irq_lateeoi(xencons->irq, eoiflag);
+
 	return recv;
 }
 
@@ -199,7 +239,7 @@
 {
 	int r;
 	uint64_t v = 0;
-	unsigned long gfn;
+	unsigned long gfn, flags;
 	struct xencons_info *info;
 
 	if (!xen_hvm_domain())
@@ -210,6 +250,7 @@
 		info = kzalloc(sizeof(struct xencons_info), GFP_KERNEL);
 		if (!info)
 			return -ENOMEM;
+		spin_lock_init(&info->ring_lock);
 	} else if (info->intf != NULL) {
 		/* already configured */
 		return 0;
@@ -234,9 +275,9 @@
 		goto err;
 	info->vtermno = HVC_COOKIE;
 
-	spin_lock(&xencons_lock);
+	spin_lock_irqsave(&xencons_lock, flags);
 	list_add_tail(&info->list, &xenconsoles);
-	spin_unlock(&xencons_lock);
+	spin_unlock_irqrestore(&xencons_lock, flags);
 
 	return 0;
 err:
@@ -246,6 +287,7 @@
 
 static int xencons_info_pv_init(struct xencons_info *info, int vtermno)
 {
+	spin_lock_init(&info->ring_lock);
 	info->evtchn = xen_start_info->console.domU.evtchn;
 	/* GFN == MFN for PV guest */
 	info->intf = gfn_to_virt(xen_start_info->console.domU.mfn);
@@ -259,6 +301,7 @@
 static int xen_pv_console_init(void)
 {
 	struct xencons_info *info;
+	unsigned long flags;
 
 	if (!xen_pv_domain())
 		return -ENODEV;
@@ -275,9 +318,9 @@
 		/* already configured */
 		return 0;
 	}
-	spin_lock(&xencons_lock);
+	spin_lock_irqsave(&xencons_lock, flags);
 	xencons_info_pv_init(info, HVC_COOKIE);
-	spin_unlock(&xencons_lock);
+	spin_unlock_irqrestore(&xencons_lock, flags);
 
 	return 0;
 }
@@ -285,6 +328,7 @@
 static int xen_initial_domain_console_init(void)
 {
 	struct xencons_info *info;
+	unsigned long flags;
 
 	if (!xen_initial_domain())
 		return -ENODEV;
@@ -294,14 +338,15 @@
 		info = kzalloc(sizeof(struct xencons_info), GFP_KERNEL);
 		if (!info)
 			return -ENOMEM;
+		spin_lock_init(&info->ring_lock);
 	}
 
 	info->irq = bind_virq_to_irq(VIRQ_CONSOLE, 0, false);
 	info->vtermno = HVC_COOKIE;
 
-	spin_lock(&xencons_lock);
+	spin_lock_irqsave(&xencons_lock, flags);
 	list_add_tail(&info->list, &xenconsoles);
-	spin_unlock(&xencons_lock);
+	spin_unlock_irqrestore(&xencons_lock, flags);
 
 	return 0;
 }
@@ -332,18 +377,21 @@
 #ifdef CONFIG_HVC_XEN_FRONTEND
 static void xencons_disconnect_backend(struct xencons_info *info)
 {
-	if (info->irq > 0)
-		unbind_from_irqhandler(info->irq, NULL);
-	info->irq = 0;
+	if (info->hvc != NULL)
+		hvc_remove(info->hvc);
+	info->hvc = NULL;
+	if (info->irq > 0) {
+		evtchn_put(info->evtchn);
+		info->irq = 0;
+		info->evtchn = 0;
+	}
+	/* evtchn_put() will also close it so this is only an error path */
 	if (info->evtchn > 0)
 		xenbus_free_evtchn(info->xbdev, info->evtchn);
 	info->evtchn = 0;
 	if (info->gntref > 0)
 		gnttab_free_grant_references(info->gntref);
 	info->gntref = 0;
-	if (info->hvc != NULL)
-		hvc_remove(info->hvc);
-	info->hvc = NULL;
 }
 
 static void xencons_free(struct xencons_info *info)
@@ -356,10 +404,12 @@
 
 static int xen_console_remove(struct xencons_info *info)
 {
+	unsigned long flags;
+
 	xencons_disconnect_backend(info);
-	spin_lock(&xencons_lock);
+	spin_lock_irqsave(&xencons_lock, flags);
 	list_del(&info->list);
-	spin_unlock(&xencons_lock);
+	spin_unlock_irqrestore(&xencons_lock, flags);
 	if (info->xbdev != NULL)
 		xencons_free(info);
 	else {
@@ -386,7 +436,7 @@
 	if (ret)
 		return ret;
 	info->evtchn = evtchn;
-	irq = bind_evtchn_to_irq(evtchn);
+	irq = bind_evtchn_to_irq_lateeoi(evtchn);
 	if (irq < 0)
 		return irq;
 	info->irq = irq;
@@ -440,6 +490,7 @@
 {
 	int ret, devid;
 	struct xencons_info *info;
+	unsigned long flags;
 
 	devid = dev->nodename[strlen(dev->nodename) - 1] - '0';
 	if (devid == 0)
@@ -448,6 +499,7 @@
 	info = kzalloc(sizeof(struct xencons_info), GFP_KERNEL);
 	if (!info)
 		return -ENOMEM;
+	spin_lock_init(&info->ring_lock);
 	dev_set_drvdata(&dev->dev, info);
 	info->xbdev = dev;
 	info->vtermno = xenbus_devid_to_vtermno(devid);
@@ -458,9 +510,9 @@
 	ret = xencons_connect_backend(dev, info);
 	if (ret < 0)
 		goto error;
-	spin_lock(&xencons_lock);
+	spin_lock_irqsave(&xencons_lock, flags);
 	list_add_tail(&info->list, &xenconsoles);
-	spin_unlock(&xencons_lock);
+	spin_unlock_irqrestore(&xencons_lock, flags);
 
 	return 0;
 
@@ -504,10 +556,23 @@
 		if (dev->state == XenbusStateClosed)
 			break;
 		fallthrough;	/* Missed the backend's CLOSING state */
-	case XenbusStateClosing:
+	case XenbusStateClosing: {
+		struct xencons_info *info = dev_get_drvdata(&dev->dev);;
+
+		/*
+		 * Don't tear down the evtchn and grant ref before the other
+		 * end has disconnected, but do stop userspace from trying
+		 * to use the device before we allow the backend to close.
+		 */
+		if (info->hvc) {
+			hvc_remove(info->hvc);
+			info->hvc = NULL;
+		}
+
 		xenbus_frontend_closed(dev);
 		break;
 	}
+	}
 }
 
 static const struct xenbus_device_id xencons_ids[] = {
@@ -538,7 +603,7 @@
 		ops = &dom0_hvc_ops;
 		r = xen_initial_domain_console_init();
 		if (r < 0)
-			return r;
+			goto register_fe;
 		info = vtermno_to_xencons(HVC_COOKIE);
 	} else {
 		ops = &domU_hvc_ops;
@@ -547,10 +612,10 @@
 		else
 			r = xen_pv_console_init();
 		if (r < 0)
-			return r;
+			goto register_fe;
 
 		info = vtermno_to_xencons(HVC_COOKIE);
-		info->irq = bind_evtchn_to_irq(info->evtchn);
+		info->irq = bind_evtchn_to_irq_lateeoi(info->evtchn);
 	}
 	if (info->irq < 0)
 		info->irq = 0; /* NO_IRQ */
@@ -559,17 +624,20 @@
 
 	info->hvc = hvc_alloc(HVC_COOKIE, info->irq, ops, 256);
 	if (IS_ERR(info->hvc)) {
+		unsigned long flags;
+
 		r = PTR_ERR(info->hvc);
-		spin_lock(&xencons_lock);
+		spin_lock_irqsave(&xencons_lock, flags);
 		list_del(&info->list);
-		spin_unlock(&xencons_lock);
+		spin_unlock_irqrestore(&xencons_lock, flags);
 		if (info->irq)
-			unbind_from_irqhandler(info->irq, NULL);
+			evtchn_put(info->evtchn);
 		kfree(info);
 		return r;
 	}
 
 	r = 0;
+ register_fe:
 #ifdef CONFIG_HVC_XEN_FRONTEND
 	r = xenbus_register_frontend(&xencons_driver);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/hvc/hvcs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/hvc/hvcs.c
@@ -52,6 +52,7 @@
 
 #include <linux/device.h>
 #include <linux/init.h>
+#include <linux/completion.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/kref.h>
@@ -284,6 +285,7 @@
 	char p_location_code[HVCS_CLC_LENGTH + 1]; /* CLC + Null Term */
 	struct list_head next; /* list management */
 	struct vio_dev *vdev;
+	struct completion *destroyed;
 };
 
 static LIST_HEAD(hvcs_structs);
@@ -431,7 +433,7 @@
 
 static DEVICE_ATTR(index, S_IRUGO, hvcs_index_show, NULL);
 
-static struct attribute *hvcs_attrs[] = {
+static struct attribute *hvcs_dev_attrs[] = {
 	&dev_attr_partner_vtys.attr,
 	&dev_attr_partner_clcs.attr,
 	&dev_attr_current_vty.attr,
@@ -440,9 +442,7 @@
 	NULL,
 };
 
-static struct attribute_group hvcs_attr_group = {
-	.attrs = hvcs_attrs,
-};
+ATTRIBUTE_GROUPS(hvcs_dev);
 
 static ssize_t rescan_show(struct device_driver *ddp, char *buf)
 {
@@ -467,6 +467,13 @@
 
 static DRIVER_ATTR_RW(rescan);
 
+static struct attribute *hvcs_attrs[] = {
+	&driver_attr_rescan.attr,
+	NULL,
+};
+
+ATTRIBUTE_GROUPS(hvcs);
+
 static void hvcs_kick(void)
 {
 	hvcs_kicked = 1;
@@ -658,11 +665,13 @@
 {
 	struct hvcs_struct *hvcsd = container_of(p, struct hvcs_struct, port);
 	struct vio_dev *vdev;
+	struct completion *comp;
 	unsigned long flags;
 
 	spin_lock(&hvcs_structs_lock);
 	spin_lock_irqsave(&hvcsd->lock, flags);
 
+	comp = hvcsd->destroyed;
 	/* the list_del poisons the pointers */
 	list_del(&(hvcsd->next));
 
@@ -682,15 +691,16 @@
 
 	hvcsd->p_unit_address = 0;
 	hvcsd->p_partition_ID = 0;
+	hvcsd->destroyed = NULL;
 	hvcs_return_index(hvcsd->index);
 	memset(&hvcsd->p_location_code[0], 0x00, HVCS_CLC_LENGTH + 1);
 
 	spin_unlock_irqrestore(&hvcsd->lock, flags);
 	spin_unlock(&hvcs_structs_lock);
 
-	sysfs_remove_group(&vdev->dev.kobj, &hvcs_attr_group);
-
 	kfree(hvcsd);
+	if (comp)
+		complete(comp);
 }
 
 static const struct tty_port_operations hvcs_port_ops = {
@@ -721,7 +731,6 @@
 {
 	struct hvcs_struct *hvcsd;
 	int index, rc;
-	int retval;
 
 	if (!dev || !id) {
 		printk(KERN_ERR "HVCS: probed with invalid parameter.\n");
@@ -778,13 +787,6 @@
 	list_add_tail(&(hvcsd->next), &hvcs_structs);
 	spin_unlock(&hvcs_structs_lock);
 
-	retval = sysfs_create_group(&dev->dev.kobj, &hvcs_attr_group);
-	if (retval) {
-		printk(KERN_ERR "HVCS: Can't create sysfs attrs for vty-server@%X\n",
-		       hvcsd->vdev->unit_address);
-		return retval;
-	}
-
 	printk(KERN_INFO "HVCS: vty-server@%X added to the vio bus.\n", dev->unit_address);
 
 	/*
@@ -797,6 +799,7 @@
 static void hvcs_remove(struct vio_dev *dev)
 {
 	struct hvcs_struct *hvcsd = dev_get_drvdata(&dev->dev);
+	DECLARE_COMPLETION_ONSTACK(comp);
 	unsigned long flags;
 	struct tty_struct *tty;
 
@@ -804,24 +807,22 @@
 
 	spin_lock_irqsave(&hvcsd->lock, flags);
 
-	tty = hvcsd->port.tty;
+	hvcsd->destroyed = &comp;
+	tty = tty_port_tty_get(&hvcsd->port);
 
 	spin_unlock_irqrestore(&hvcsd->lock, flags);
 
 	/*
-	 * Let the last holder of this object cause it to be removed, which
-	 * would probably be tty_hangup below.
-	 */
-	tty_port_put(&hvcsd->port);
-
-	/*
-	 * The hangup is a scheduled function which will auto chain call
-	 * hvcs_hangup.  The tty should always be valid at this time unless a
+	 * The tty should always be valid at this time unless a
 	 * simultaneous tty close already cleaned up the hvcs_struct.
 	 */
-	if (tty)
-		tty_hangup(tty);
+	if (tty) {
+		tty_vhangup(tty);
+		tty_kref_put(tty);
+	}
 
+	tty_port_put(&hvcsd->port);
+	wait_for_completion(&comp);
 	printk(KERN_INFO "HVCS: vty-server@%X removed from the"
 			" vio bus.\n", dev->unit_address);
 };
@@ -831,6 +832,10 @@
 	.probe		= hvcs_probe,
 	.remove		= hvcs_remove,
 	.name		= hvcs_driver_name,
+	.driver = {
+		.groups = hvcs_groups,
+		.dev_groups = hvcs_dev_groups,
+	},
 };
 
 /* Only called from hvcs_get_pi please */
@@ -1171,7 +1176,10 @@
 	hvcsd = tty->driver_data;
 
 	spin_lock_irqsave(&hvcsd->lock, flags);
-	if (--hvcsd->port.count == 0) {
+	if (hvcsd->port.count == 0) {
+		spin_unlock_irqrestore(&hvcsd->lock, flags);
+		return;
+	} else if (--hvcsd->port.count == 0) {
 
 		vio_disable_interrupts(hvcsd->vdev);
 
@@ -1215,12 +1223,9 @@
 {
 	struct hvcs_struct *hvcsd = tty->driver_data;
 	unsigned long flags;
-	int temp_open_count;
 	int irq;
 
 	spin_lock_irqsave(&hvcsd->lock, flags);
-	/* Preserve this so that we know how many kref refs to put */
-	temp_open_count = hvcsd->port.count;
 
 	/*
 	 * Don't kref put inside the spinlock because the destruction
@@ -1230,11 +1235,7 @@
 	vio_disable_interrupts(hvcsd->vdev);
 
 	hvcsd->todo_mask = 0;
-
-	/* I don't think the tty needs the hvcs_struct pointer after a hangup */
-	tty->driver_data = NULL;
 	hvcsd->port.tty = NULL;
-
 	hvcsd->port.count = 0;
 
 	/* This will drop any buffered data on the floor which is OK in a hangup
@@ -1247,21 +1248,6 @@
 	spin_unlock_irqrestore(&hvcsd->lock, flags);
 
 	free_irq(irq, hvcsd);
-
-	/*
-	 * We need to kref_put() for every open_count we have since the
-	 * tty_hangup() function doesn't invoke a close per open connection on a
-	 * non-console device.
-	 */
-	while(temp_open_count) {
-		--temp_open_count;
-		/*
-		 * The final put will trigger destruction of the hvcs_struct.
-		 * NOTE:  If this hangup was signaled from user space then the
-		 * final put will never happen.
-		 */
-		tty_port_put(&hvcsd->port);
-	}
 }
 
 /*
@@ -1525,13 +1511,6 @@
 
 	pr_info("HVCS: Driver registered.\n");
 
-	/* This needs to be done AFTER the vio_register_driver() call or else
-	 * the kobjects won't be initialized properly.
-	 */
-	rc = driver_create_file(&(hvcs_vio_driver.driver), &driver_attr_rescan);
-	if (rc)
-		pr_warn("HVCS: Failed to create rescan file (err %d)\n", rc);
-
 	return 0;
 }
 
@@ -1556,8 +1535,6 @@
 	hvcs_pi_buff = NULL;
 	spin_unlock(&hvcs_pi_lock);
 
-	driver_remove_file(&hvcs_vio_driver.driver, &driver_attr_rescan);
-
 	tty_unregister_driver(hvcs_tty_driver);
 
 	hvcs_free_index_list();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/moxa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/moxa.c
@@ -1383,7 +1383,7 @@
 		if (inited && !tty_throttled(tty) &&
 				MoxaPortRxQueue(p) > 0) { /* RX */
 			MoxaPortReadData(p);
-			tty_schedule_flip(&p->port);
+			tty_flip_buffer_push(&p->port);
 		}
 	} else {
 		clear_bit(EMPTYWAIT, &p->statusflags);
@@ -1408,7 +1408,7 @@
 
 	if (tty && (intr & IntrBreak) && !I_IGNBRK(tty)) { /* BREAK */
 		tty_insert_flip_char(&p->port, 0, TTY_BREAK);
-		tty_schedule_flip(&p->port);
+		tty_flip_buffer_push(&p->port);
 	}
 
 	if (intr & IntrLine)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/mxser.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/mxser.c
@@ -261,7 +261,6 @@
 	unsigned int xmit_head;
 	unsigned int xmit_tail;
 	unsigned int xmit_cnt;
-	int closing;
 
 	spinlock_t slock;
 };
@@ -712,6 +711,7 @@
 	struct mxser_port *info = container_of(port, struct mxser_port, port);
 	unsigned long page;
 	unsigned long flags;
+	int ret;
 
 	page = __get_free_page(GFP_KERNEL);
 	if (!page)
@@ -721,9 +721,9 @@
 
 	if (!info->type) {
 		set_bit(TTY_IO_ERROR, &tty->flags);
-		free_page(page);
 		spin_unlock_irqrestore(&info->slock, flags);
-		return 0;
+		ret = 0;
+		goto err_free_xmit;
 	}
 	info->port.xmit_buf = (unsigned char *) page;
 
@@ -749,8 +749,10 @@
 		if (capable(CAP_SYS_ADMIN)) {
 			set_bit(TTY_IO_ERROR, &tty->flags);
 			return 0;
-		} else
-			return -ENODEV;
+		}
+
+		ret = -ENODEV;
+		goto err_free_xmit;
 	}
 
 	/*
@@ -795,6 +797,10 @@
 	spin_unlock_irqrestore(&info->slock, flags);
 
 	return 0;
+err_free_xmit:
+	free_page(page);
+	info->port.xmit_buf = NULL;
+	return ret;
 }
 
 /*
@@ -923,7 +929,6 @@
 		return;
 	if (tty_port_close_start(port, tty, filp) == 0)
 		return;
-	info->closing = 1;
 	mutex_lock(&port->mutex);
 	mxser_close_port(port);
 	mxser_flush_buffer(tty);
@@ -932,7 +937,6 @@
 	mxser_shutdown_port(port);
 	tty_port_set_initialized(port, 0);
 	mutex_unlock(&port->mutex);
-	info->closing = 0;
 	/* Right now the tty_port set is done outside of the close_end helper
 	   as we don't yet have everyone using refcounts */	
 	tty_port_close_end(port, tty);
@@ -1693,7 +1697,7 @@
 
 	iir &= MOXA_MUST_IIR_MASK;
 	tty = tty_port_tty_get(&port->port);
-	if (!tty || port->closing || !tty_port_initialized(&port->port)) {
+	if (!tty) {
 		status = inb(port->ioaddr + UART_LSR);
 		outb(MOXA_MUST_FCR_GDA_MODE_ENABLE | UART_FCR_ENABLE_FIFO |
 				UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/n_gsm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/n_gsm.c
@@ -73,6 +73,8 @@
  */
 #define MAX_MRU 1500
 #define MAX_MTU 1500
+/* SOF, ADDR, CTRL, LEN1, LEN2, ..., FCS, EOF */
+#define PROT_OVERHEAD 7
 #define	GSM_NET_TX_TIMEOUT (HZ*10)
 
 /*
@@ -135,6 +137,7 @@
 	int retries;
 	/* Uplink tty if active */
 	struct tty_port port;	/* The tty bound to this DLCI if there is one */
+#define TX_SIZE		4096    /* Must be power of 2. */
 	struct kfifo fifo;	/* Queue fifo for the DLCI */
 	int adaption;		/* Adaption layer in use */
 	int prev_adaption;
@@ -175,16 +178,18 @@
 
 enum gsm_mux_state {
 	GSM_SEARCH,
-	GSM_START,
-	GSM_ADDRESS,
-	GSM_CONTROL,
-	GSM_LEN,
-	GSM_DATA,
-	GSM_FCS,
-	GSM_OVERRUN,
-	GSM_LEN0,
-	GSM_LEN1,
-	GSM_SSOF,
+	GSM0_ADDRESS,
+	GSM0_CONTROL,
+	GSM0_LEN0,
+	GSM0_LEN1,
+	GSM0_DATA,
+	GSM0_FCS,
+	GSM0_SSOF,
+	GSM1_START,
+	GSM1_ADDRESS,
+	GSM1_CONTROL,
+	GSM1_DATA,
+	GSM1_OVERRUN,
 };
 
 /*
@@ -219,7 +224,6 @@
 	int encoding;
 	u8 control;
 	u8 fcs;
-	u8 received_fcs;
 	u8 *txframe;			/* TX framing buffer */
 
 	/* Method for the receiver side */
@@ -231,7 +235,9 @@
 	int initiator;			/* Did we initiate connection */
 	bool dead;			/* Has the mux been shut down */
 	struct gsm_dlci *dlci[NUM_DLCI];
+	int old_c_iflag;		/* termios c_iflag value before attach */
 	bool constipated;		/* Asked by remote to shut up */
+	bool has_devices;		/* Devices were registered */
 
 	spinlock_t tx_lock;
 	unsigned int tx_bytes;		/* TX data outstanding */
@@ -240,6 +246,7 @@
 	struct list_head tx_list;	/* Pending data packets */
 
 	/* Control messages */
+	struct timer_list kick_timer;	/* Kick TX queuing on timeout */
 	struct timer_list t2_timer;	/* Retransmit timer for commands */
 	int cretries;			/* Command retry counter */
 	struct gsm_control *pending_cmd;/* Our current pending command */
@@ -271,6 +278,10 @@
 
 static struct tty_driver *gsm_tty_driver;
 
+/* Save dlci open address */
+static int addr_open[256] = { 0 };
+/* Save dlci open count */
+static int addr_cnt;
 /*
  *	This section of the driver logic implements the GSM encodings
  *	both the basic and the 'advanced'. Reliable transport is not
@@ -318,6 +329,7 @@
 #define GSM1_ESCAPE_BITS	0x20
 #define XON			0x11
 #define XOFF			0x13
+#define ISO_IEC_646_MASK	0x7F
 
 static const struct tty_port_operations gsm_port_ops;
 
@@ -364,6 +376,7 @@
 #define GOOD_FCS	0xCF
 
 static int gsmld_output(struct gsm_mux *gsm, u8 *data, int len);
+static int gsm_modem_update(struct gsm_dlci *dlci, u8 brk);
 
 /**
  *	gsm_fcs_add	-	update FCS
@@ -415,6 +428,27 @@
 }
 
 /**
+ *	gsm_read_ea_val	-	read a value until EA
+ *	@val: variable holding value
+ *	@data: buffer of data
+ *	@dlen: length of data
+ *
+ *	Processes an EA value. Updates the passed variable and
+ *	returns the processed data length.
+ */
+static unsigned int gsm_read_ea_val(unsigned int *val, const u8 *data, int dlen)
+{
+	unsigned int len = 0;
+
+	for (; dlen > 0; dlen--) {
+		len++;
+		if (gsm_read_ea(val, *data++))
+			break;
+	}
+	return len;
+}
+
+/**
  *	gsm_encode_modem	-	encode modem data bits
  *	@dlci: DLCI to encode from
  *
@@ -434,16 +468,97 @@
 		modembits |= MDM_RTR;
 	if (dlci->modem_tx & TIOCM_RI)
 		modembits |= MDM_IC;
-	if (dlci->modem_tx & TIOCM_CD)
+	if (dlci->modem_tx & TIOCM_CD || dlci->gsm->initiator)
 		modembits |= MDM_DV;
 	return modembits;
 }
 
+static void gsm_hex_dump_bytes(const char *fname, const u8 *data,
+			       unsigned long len)
+{
+	char *prefix;
+
+	if (!fname) {
+		print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 1, data, len,
+			       true);
+		return;
+	}
+
+	prefix = kasprintf(GFP_ATOMIC, "%s: ", fname);
+	if (!prefix)
+		return;
+	print_hex_dump(KERN_INFO, prefix, DUMP_PREFIX_OFFSET, 16, 1, data, len,
+		       true);
+	kfree(prefix);
+}
+
+/**
+ *	gsm_register_devices	-	register all tty devices for a given mux index
+ *
+ *	@driver: the tty driver that describes the tty devices
+ *	@index:  the mux number is used to calculate the minor numbers of the
+ *	         ttys for this mux and may differ from the position in the
+ *	         mux array.
+ */
+static int gsm_register_devices(struct tty_driver *driver, unsigned int index)
+{
+	struct device *dev;
+	int i;
+	unsigned int base;
+
+	if (!driver || index >= MAX_MUX)
+		return -EINVAL;
+
+	base = index * NUM_DLCI; /* first minor for this index */
+	for (i = 1; i < NUM_DLCI; i++) {
+		/* Don't register device 0 - this is the control channel
+		 * and not a usable tty interface
+		 */
+		dev = tty_register_device(gsm_tty_driver, base + i, NULL);
+		if (IS_ERR(dev)) {
+			if (debug & 8)
+				pr_info("%s failed to register device minor %u",
+					__func__, base + i);
+			for (i--; i >= 1; i--)
+				tty_unregister_device(gsm_tty_driver, base + i);
+			return PTR_ERR(dev);
+		}
+	}
+
+	return 0;
+}
+
+/**
+ *	gsm_unregister_devices	-	unregister all tty devices for a given mux index
+ *
+ *	@driver: the tty driver that describes the tty devices
+ *	@index:  the mux number is used to calculate the minor numbers of the
+ *	         ttys for this mux and may differ from the position in the
+ *	         mux array.
+ */
+static void gsm_unregister_devices(struct tty_driver *driver,
+				   unsigned int index)
+{
+	int i;
+	unsigned int base;
+
+	if (!driver || index >= MAX_MUX)
+		return;
+
+	base = index * NUM_DLCI; /* first minor for this index */
+	for (i = 1; i < NUM_DLCI; i++) {
+		/* Don't unregister device 0 - this is the control
+		 * channel and not a usable tty interface
+		 */
+		tty_unregister_device(gsm_tty_driver, base + i);
+	}
+}
+
 /**
  *	gsm_print_packet	-	display a frame for debug
  *	@hdr: header to print before decode
  *	@addr: address EA from the frame
- *	@cr: C/R bit from the frame
+ *	@cr: C/R bit seen as initiator
  *	@control: control including PF bit
  *	@data: following data bytes
  *	@dlen: length of data
@@ -503,7 +618,7 @@
 	else
 		pr_cont("(F)");
 
-	print_hex_dump_bytes("", DUMP_PREFIX_NONE, data, dlen);
+	gsm_hex_dump_bytes(NULL, data, dlen);
 }
 
 
@@ -527,7 +642,8 @@
 	int olen = 0;
 	while (len--) {
 		if (*input == GSM1_SOF || *input == GSM1_ESCAPE
-		    || *input == XON || *input == XOFF) {
+		    || (*input & ISO_IEC_646_MASK) == XON
+		    || (*input & ISO_IEC_646_MASK) == XOFF) {
 			*output++ = GSM1_ESCAPE;
 			*output++ = *input++ ^ GSM1_ESCAPE_BITS;
 			olen++;
@@ -542,7 +658,7 @@
  *	gsm_send	-	send a control frame
  *	@gsm: our GSM mux
  *	@addr: address for control frame
- *	@cr: command/response bit
+ *	@cr: command/response bit seen as initiator
  *	@control:  control byte including PF bit
  *
  *	Format up and transmit a control frame. These do not go via the
@@ -557,11 +673,15 @@
 	int len;
 	u8 cbuf[10];
 	u8 ibuf[3];
+	int ocr;
+
+	/* toggle C/R coding if not initiator */
+	ocr = cr ^ (gsm->initiator ? 0 : 1);
 
 	switch (gsm->encoding) {
 	case 0:
 		cbuf[0] = GSM0_SOF;
-		cbuf[1] = (addr << 2) | (cr << 1) | EA;
+		cbuf[1] = (addr << 2) | (ocr << 1) | EA;
 		cbuf[2] = control;
 		cbuf[3] = EA;	/* Length of data = 0 */
 		cbuf[4] = 0xFF - gsm_fcs_add_block(INIT_FCS, cbuf + 1, 3);
@@ -571,7 +691,7 @@
 	case 1:
 	case 2:
 		/* Control frame + packing (but not frame stuffing) in mode 1 */
-		ibuf[0] = (addr << 2) | (cr << 1) | EA;
+		ibuf[0] = (addr << 2) | (ocr << 1) | EA;
 		ibuf[1] = control;
 		ibuf[2] = 0xFF - gsm_fcs_add_block(INIT_FCS, ibuf, 2);
 		/* Stuffing may double the size worst case */
@@ -650,6 +770,37 @@
 }
 
 /**
+ *	gsm_is_flow_ctrl_msg	-	checks if flow control message
+ *	@msg: message to check
+ *
+ *	Returns true if the given message is a flow control command of the
+ *	control channel. False is returned in any other case.
+ */
+static bool gsm_is_flow_ctrl_msg(struct gsm_msg *msg)
+{
+	unsigned int cmd;
+
+	if (msg->addr > 0)
+		return false;
+
+	switch (msg->ctrl & ~PF) {
+	case UI:
+	case UIH:
+		cmd = 0;
+		if (gsm_read_ea_val(&cmd, msg->data + 2, msg->len - 2) < 1)
+			break;
+		switch (cmd & ~PF) {
+		case CMD_FCOFF:
+		case CMD_FCON:
+			return true;
+		}
+		break;
+	}
+
+	return false;
+}
+
+/**
  *	gsm_data_kick		-	poke the queue
  *	@gsm: GSM Mux
  *	@dlci: DLCI sending the data
@@ -668,7 +819,7 @@
 	int len;
 
 	list_for_each_entry_safe(msg, nmsg, &gsm->tx_list, list) {
-		if (gsm->constipated && msg->addr)
+		if (gsm->constipated && !gsm_is_flow_ctrl_msg(msg))
 			continue;
 		if (gsm->encoding != 0) {
 			gsm->txframe[0] = GSM1_SOF;
@@ -684,10 +835,8 @@
 		}
 
 		if (debug & 4)
-			print_hex_dump_bytes("gsm_data_kick: ",
-					     DUMP_PREFIX_OFFSET,
-					     gsm->txframe, len);
-		if (gsmld_output(gsm, gsm->txframe, len) < 0)
+			gsm_hex_dump_bytes(__func__, gsm->txframe, len);
+		if (gsmld_output(gsm, gsm->txframe, len) <= 0)
 			break;
 		/* FIXME: Can eliminate one SOF in many more cases */
 		gsm->tx_bytes -= msg->len;
@@ -756,6 +905,7 @@
 	list_add_tail(&msg->list, &gsm->tx_list);
 	gsm->tx_bytes += msg->len;
 	gsm_data_kick(gsm, dlci);
+	mod_timer(&gsm->kick_timer, jiffies + 10 * gsm->t1 * HZ / 100);
 }
 
 /**
@@ -792,41 +942,48 @@
 {
 	struct gsm_msg *msg;
 	u8 *dp;
-	int len, total_size, size;
-	int h = dlci->adaption - 1;
+	int h, len, size;
 
-	total_size = 0;
-	while (1) {
-		len = kfifo_len(&dlci->fifo);
-		if (len == 0)
-			return total_size;
+	/* for modem bits without break data */
+	h = ((dlci->adaption == 1) ? 0 : 1);
 
-		/* MTU/MRU count only the data bits */
-		if (len > gsm->mtu)
-			len = gsm->mtu;
-
-		size = len + h;
-
-		msg = gsm_data_alloc(gsm, dlci->addr, size, gsm->ftype);
-		/* FIXME: need a timer or something to kick this so it can't
-		   get stuck with no work outstanding and no buffer free */
-		if (msg == NULL)
-			return -ENOMEM;
-		dp = msg->data;
-		switch (dlci->adaption) {
-		case 1:	/* Unstructured */
-			break;
-		case 2:	/* Unstructed with modem bits.
-		Always one byte as we never send inline break data */
-			*dp++ = gsm_encode_modem(dlci);
-			break;
-		}
-		WARN_ON(kfifo_out_locked(&dlci->fifo, dp , len, &dlci->lock) != len);
-		__gsm_data_queue(dlci, msg);
-		total_size += size;
+	len = kfifo_len(&dlci->fifo);
+	if (len == 0)
+		return 0;
+
+	/* MTU/MRU count only the data bits but watch adaption mode */
+	if ((len + h) > gsm->mtu)
+		len = gsm->mtu - h;
+
+	size = len + h;
+
+	msg = gsm_data_alloc(gsm, dlci->addr, size, gsm->ftype);
+	if (!msg)
+		return -ENOMEM;
+	dp = msg->data;
+	switch (dlci->adaption) {
+	case 1: /* Unstructured */
+		break;
+	case 2: /* Unstructured with modem bits.
+		 * Always one byte as we never send inline break data
+		 */
+		*dp++ = (gsm_encode_modem(dlci) << 1) | EA;
+		break;
+	default:
+		pr_err("%s: unsupported adaption %d\n", __func__,
+		       dlci->adaption);
+		break;
 	}
+
+	WARN_ON(len != kfifo_out_locked(&dlci->fifo, dp, len,
+		&dlci->lock));
+
+	/* Notify upper layer about available send space. */
+	tty_port_tty_wakeup(&dlci->port);
+
+	__gsm_data_queue(dlci, msg);
 	/* Bytes of data we used up */
-	return total_size;
+	return size;
 }
 
 /**
@@ -877,9 +1034,6 @@
 
 	size = len + overhead;
 	msg = gsm_data_alloc(gsm, dlci->addr, size, gsm->ftype);
-
-	/* FIXME: need a timer or something to kick this so it can't
-	   get stuck with no work outstanding and no buffer free */
 	if (msg == NULL) {
 		skb_queue_tail(&dlci->skb_list, dlci->skb);
 		dlci->skb = NULL;
@@ -903,6 +1057,66 @@
 }
 
 /**
+ *	gsm_dlci_modem_output	-	try and push modem status out of a DLCI
+ *	@gsm: mux
+ *	@dlci: the DLCI to pull modem status from
+ *	@brk: break signal
+ *
+ *	Push an empty frame in to the transmit queue to update the modem status
+ *	bits and to transmit an optional break.
+ *
+ *	Caller must hold the tx_lock of the mux.
+ */
+
+static int gsm_dlci_modem_output(struct gsm_mux *gsm, struct gsm_dlci *dlci,
+				 u8 brk)
+{
+	u8 *dp = NULL;
+	struct gsm_msg *msg;
+	int size = 0;
+
+	/* for modem bits without break data */
+	switch (dlci->adaption) {
+	case 1: /* Unstructured */
+		break;
+	case 2: /* Unstructured with modem bits. */
+		size++;
+		if (brk > 0)
+			size++;
+		break;
+	default:
+		pr_err("%s: unsupported adaption %d\n", __func__,
+		       dlci->adaption);
+		return -EINVAL;
+	}
+
+	msg = gsm_data_alloc(gsm, dlci->addr, size, gsm->ftype);
+	if (!msg) {
+		pr_err("%s: gsm_data_alloc error", __func__);
+		return -ENOMEM;
+	}
+	dp = msg->data;
+	switch (dlci->adaption) {
+	case 1: /* Unstructured */
+		break;
+	case 2: /* Unstructured with modem bits. */
+		if (brk == 0) {
+			*dp++ = (gsm_encode_modem(dlci) << 1) | EA;
+		} else {
+			*dp++ = gsm_encode_modem(dlci) << 1;
+			*dp++ = (brk << 4) | 2 | EA; /* Length, Break, EA */
+		}
+		break;
+	default:
+		/* Handled above */
+		break;
+	}
+
+	__gsm_data_queue(dlci, msg);
+	return size;
+}
+
+/**
  *	gsm_dlci_data_sweep		-	look for data to send
  *	@gsm: the GSM mux
  *
@@ -915,9 +1129,9 @@
  *	renegotiate DLCI priorities with optional stuff. Needs optimising.
  */
 
-static void gsm_dlci_data_sweep(struct gsm_mux *gsm)
+static int gsm_dlci_data_sweep(struct gsm_mux *gsm)
 {
-	int len;
+	int len, ret = 0;
 	/* Priority ordering: We should do priority with RR of the groups */
 	int i = 1;
 
@@ -940,7 +1154,11 @@
 		/* DLCI empty - try the next */
 		if (len == 0)
 			i++;
+		else
+			ret++;
 	}
+
+	return ret;
 }
 
 /**
@@ -1007,25 +1225,25 @@
  *	@tty: virtual tty bound to the DLCI
  *	@dlci: DLCI to affect
  *	@modem: modem bits (full EA)
- *	@clen: command length
+ *	@slen: number of signal octets
  *
  *	Used when a modem control message or line state inline in adaption
  *	layer 2 is processed. Sort out the local modem state and throttles
  */
 
 static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci,
-							u32 modem, int clen)
+							u32 modem, int slen)
 {
 	int  mlines = 0;
 	u8 brk = 0;
 	int fc;
 
-	/* The modem status command can either contain one octet (v.24 signals)
-	   or two octets (v.24 signals + break signals). The length field will
-	   either be 2 or 3 respectively. This is specified in section
-	   5.4.6.3.7 of the  27.010 mux spec. */
+	/* The modem status command can either contain one octet (V.24 signals)
+	 * or two octets (V.24 signals + break signals). This is specified in
+	 * section 5.4.6.3.7 of the 07.10 mux spec.
+	 */
 
-	if (clen == 2)
+	if (slen == 1)
 		modem = modem & 0x7f;
 	else {
 		brk = modem & 0x7f;
@@ -1079,9 +1297,9 @@
 {
 	unsigned int addr = 0;
 	unsigned int modem = 0;
-	unsigned int brk = 0;
 	struct gsm_dlci *dlci;
 	int len = clen;
+	int slen;
 	const u8 *dp = data;
 	struct tty_struct *tty;
 
@@ -1101,23 +1319,15 @@
 		return;
 	dlci = gsm->dlci[addr];
 
+	slen = len;
 	while (gsm_read_ea(&modem, *dp++) == 0) {
 		len--;
 		if (len == 0)
 			return;
 	}
 	len--;
-	if (len > 0) {
-		while (gsm_read_ea(&brk, *dp++) == 0) {
-			len--;
-			if (len == 0)
-				return;
-		}
-		modem <<= 7;
-		modem |= (brk & 0x7f);
-	}
 	tty = tty_port_tty_get(&dlci->port);
-	gsm_process_modem(tty, dlci, modem, clen);
+	gsm_process_modem(tty, dlci, modem, slen - len);
 	if (tty) {
 		tty_wakeup(tty);
 		tty_kref_put(tty);
@@ -1177,6 +1387,7 @@
 }
 
 static void gsm_dlci_begin_close(struct gsm_dlci *dlci);
+static void gsm_dlci_close(struct gsm_dlci *dlci);
 
 /**
  *	gsm_control_message	-	DLCI 0 control processing
@@ -1195,15 +1406,28 @@
 {
 	u8 buf[1];
 	unsigned long flags;
+	struct gsm_dlci *dlci;
+	int i;
+	int address;
 
 	switch (command) {
 	case CMD_CLD: {
-		struct gsm_dlci *dlci = gsm->dlci[0];
+		if (addr_cnt > 0) {
+			for (i = 0; i < addr_cnt; i++) {
+				address = addr_open[i];
+				dlci = gsm->dlci[address];
+				gsm_dlci_close(dlci);
+				addr_open[i] = 0;
+			}
+		}
 		/* Modem wishes to close down */
+		dlci = gsm->dlci[0];
 		if (dlci) {
 			dlci->dead = true;
 			gsm->dead = true;
-			gsm_dlci_begin_close(dlci);
+			gsm_dlci_close(dlci);
+			addr_cnt = 0;
+			gsm_response(gsm, 0, UA|PF);
 		}
 		}
 		break;
@@ -1296,11 +1520,12 @@
 
 static void gsm_control_transmit(struct gsm_mux *gsm, struct gsm_control *ctrl)
 {
-	struct gsm_msg *msg = gsm_data_alloc(gsm, 0, ctrl->len + 1, gsm->ftype);
+	struct gsm_msg *msg = gsm_data_alloc(gsm, 0, ctrl->len + 2, gsm->ftype);
 	if (msg == NULL)
 		return;
-	msg->data[0] = (ctrl->cmd << 1) | 2 | EA;	/* command */
-	memcpy(msg->data + 1, ctrl->data, ctrl->len);
+	msg->data[0] = (ctrl->cmd << 1) | CR | EA;	/* command */
+	msg->data[1] = (ctrl->len << 1) | EA;
+	memcpy(msg->data + 2, ctrl->data, ctrl->len);
 	gsm_data_queue(gsm->dlci[0], msg);
 }
 
@@ -1323,8 +1548,7 @@
 	spin_lock_irqsave(&gsm->control_lock, flags);
 	ctrl = gsm->pending_cmd;
 	if (ctrl) {
-		gsm->cretries--;
-		if (gsm->cretries == 0) {
+		if (gsm->cretries == 0 || !gsm->dlci[0] || gsm->dlci[0]->dead) {
 			gsm->pending_cmd = NULL;
 			ctrl->error = -ETIMEDOUT;
 			ctrl->done = 1;
@@ -1332,6 +1556,7 @@
 			wake_up(&gsm->event);
 			return;
 		}
+		gsm->cretries--;
 		gsm_control_transmit(gsm, ctrl);
 		mod_timer(&gsm->t2_timer, jiffies + gsm->t2 * HZ / 100);
 	}
@@ -1354,7 +1579,7 @@
 		unsigned int command, u8 *data, int clen)
 {
 	struct gsm_control *ctrl = kzalloc(sizeof(struct gsm_control),
-						GFP_KERNEL);
+						GFP_ATOMIC);
 	unsigned long flags;
 	if (ctrl == NULL)
 		return NULL;
@@ -1372,7 +1597,7 @@
 
 	/* If DLCI0 is in ADM mode skip retries, it won't respond */
 	if (gsm->dlci[0]->mode == DLCI_MODE_ADM)
-		gsm->cretries = 1;
+		gsm->cretries = 0;
 	else
 		gsm->cretries = gsm->n2;
 
@@ -1420,13 +1645,22 @@
 
 static void gsm_dlci_close(struct gsm_dlci *dlci)
 {
+	unsigned long flags;
+
 	del_timer(&dlci->t1);
 	if (debug & 8)
 		pr_debug("DLCI %d goes closed.\n", dlci->addr);
 	dlci->state = DLCI_CLOSED;
+	/* Prevent us from sending data before the link is up again */
+	dlci->constipated = true;
 	if (dlci->addr != 0) {
 		tty_port_tty_hangup(&dlci->port, false);
+		spin_lock_irqsave(&dlci->lock, flags);
 		kfifo_reset(&dlci->fifo);
+		spin_unlock_irqrestore(&dlci->lock, flags);
+		/* Ensure that gsmtty_open() can return. */
+		tty_port_set_initialized(&dlci->port, 0);
+		wake_up_interruptible(&dlci->port.open_wait);
 	} else
 		dlci->gsm->dead = true;
 	wake_up(&dlci->gsm->event);
@@ -1448,8 +1682,12 @@
 	del_timer(&dlci->t1);
 	/* This will let a tty open continue */
 	dlci->state = DLCI_OPEN;
+	dlci->constipated = false;
 	if (debug & 8)
 		pr_debug("DLCI %d goes open.\n", dlci->addr);
+	/* Send current modem state */
+	if (dlci->addr)
+		gsm_modem_update(dlci, 0);
 	wake_up(&dlci->gsm->event);
 }
 
@@ -1475,8 +1713,8 @@
 
 	switch (dlci->state) {
 	case DLCI_OPENING:
-		dlci->retries--;
 		if (dlci->retries) {
+			dlci->retries--;
 			gsm_command(dlci->gsm, dlci->addr, SABM|PF);
 			mod_timer(&dlci->t1, jiffies + gsm->t1 * HZ / 100);
 		} else if (!dlci->addr && gsm->control == (DM | PF)) {
@@ -1486,13 +1724,13 @@
 			dlci->mode = DLCI_MODE_ADM;
 			gsm_dlci_open(dlci);
 		} else {
-			gsm_dlci_close(dlci);
+			gsm_dlci_begin_close(dlci); /* prevent half open link */
 		}
 
 		break;
 	case DLCI_CLOSING:
-		dlci->retries--;
 		if (dlci->retries) {
+			dlci->retries--;
 			gsm_command(dlci->gsm, dlci->addr, DISC|PF);
 			mod_timer(&dlci->t1, jiffies + gsm->t1 * HZ / 100);
 		} else
@@ -1526,6 +1764,25 @@
 }
 
 /**
+ *	gsm_dlci_set_opening	-	change state to opening
+ *	@dlci: DLCI to open
+ *
+ *	Change internal state to wait for DLCI open from initiator side.
+ *	We set off timers and responses upon reception of an SABM.
+ */
+static void gsm_dlci_set_opening(struct gsm_dlci *dlci)
+{
+	switch (dlci->state) {
+	case DLCI_CLOSED:
+	case DLCI_CLOSING:
+		dlci->state = DLCI_OPENING;
+		break;
+	default:
+		break;
+	}
+}
+
+/**
  *	gsm_dlci_begin_close	-	start channel open procedure
  *	@dlci: DLCI to open
  *
@@ -1565,6 +1822,7 @@
 	struct tty_struct *tty;
 	unsigned int modem = 0;
 	int len = clen;
+	int slen = 0;
 
 	if (debug & 16)
 		pr_debug("%d bytes for tty\n", len);
@@ -1577,12 +1835,16 @@
 	case 2:		/* Asynchronous serial with line state in each frame */
 		while (gsm_read_ea(&modem, *data++) == 0) {
 			len--;
+			slen++;
 			if (len == 0)
 				return;
 		}
+		len--;
+		slen++;
 		tty = tty_port_tty_get(port);
 		if (tty) {
-			gsm_process_modem(tty, dlci, modem, clen);
+			gsm_process_modem(tty, dlci, modem, slen);
+			tty_wakeup(tty);
 			tty_kref_put(tty);
 		}
 		fallthrough;
@@ -1629,6 +1891,30 @@
 	}
 }
 
+/**
+ *	gsm_kick_timer	-	transmit if possible
+ *	@t: timer contained in our gsm object
+ *
+ *	Transmit data from DLCIs if the queue is empty. We can't rely on
+ *	a tty wakeup except when we filled the pipe so we need to fire off
+ *	new data ourselves in other cases.
+ */
+static void gsm_kick_timer(struct timer_list *t)
+{
+	struct gsm_mux *gsm = from_timer(gsm, t, kick_timer);
+	unsigned long flags;
+	int sent = 0;
+
+	spin_lock_irqsave(&gsm->tx_lock, flags);
+	/* If we have nothing running then we need to fire up */
+	if (gsm->tx_bytes < TX_THRESH_LO)
+		sent = gsm_dlci_data_sweep(gsm);
+	spin_unlock_irqrestore(&gsm->tx_lock, flags);
+
+	if (sent && debug & 4)
+		pr_info("%s TX queue stalled\n", __func__);
+}
+
 /*
  *	Allocate/Free DLCI channels
  */
@@ -1650,7 +1936,7 @@
 		return NULL;
 	spin_lock_init(&dlci->lock);
 	mutex_init(&dlci->mutex);
-	if (kfifo_alloc(&dlci->fifo, 4096, GFP_KERNEL) < 0) {
+	if (kfifo_alloc(&dlci->fifo, TX_SIZE, GFP_KERNEL) < 0) {
 		kfree(dlci);
 		return NULL;
 	}
@@ -1663,10 +1949,13 @@
 	dlci->addr = addr;
 	dlci->adaption = gsm->adaption;
 	dlci->state = DLCI_CLOSED;
-	if (addr)
+	if (addr) {
 		dlci->data = gsm_dlci_data;
-	else
+		/* Prevent us from sending data before the link is up */
+		dlci->constipated = true;
+	} else {
 		dlci->data = gsm_dlci_command;
+	}
 	gsm->dlci[addr] = dlci;
 	return dlci;
 }
@@ -1720,7 +2009,12 @@
 		gsm_destroy_network(dlci);
 		mutex_unlock(&dlci->mutex);
 
-		tty_hangup(tty);
+		/* We cannot use tty_hangup() because in tty_kref_put() the tty
+		 * driver assumes that the hangup queue is free and reuses it to
+		 * queue release_one_tty() -> NULL pointer panic in
+		 * process_one_work().
+		 */
+		tty_vhangup(tty);
 
 		tty_port_tty_set(&dlci->port, NULL);
 		tty_kref_put(tty);
@@ -1748,18 +2042,8 @@
 	struct gsm_dlci *dlci;
 	u8 cr;
 	int address;
-	/* We have to sneak a look at the packet body to do the FCS.
-	   A somewhat layering violation in the spec */
+	int i, j, k, address_tmp;
 
-	if ((gsm->control & ~PF) == UI)
-		gsm->fcs = gsm_fcs_add_block(gsm->fcs, gsm->buf, gsm->len);
-	if (gsm->encoding == 0) {
-		/* WARNING: gsm->received_fcs is used for
-		gsm->encoding = 0 only.
-		In this case it contain the last piece of data
-		required to generate final CRC */
-		gsm->fcs = gsm_fcs_add(gsm->fcs, gsm->received_fcs);
-	}
 	if (gsm->fcs != GOOD_FCS) {
 		gsm->bad_fcs++;
 		if (debug & 4)
@@ -1771,10 +2055,10 @@
 		goto invalid;
 
 	cr = gsm->address & 1;		/* C/R bit */
+	cr ^= gsm->initiator ? 0 : 1;	/* Flip so 1 always means command */
 
 	gsm_print_packet("<--", address, cr, gsm->control, gsm->buf, gsm->len);
 
-	cr ^= 1 - gsm->initiator;	/* Flip so 1 always means command */
 	dlci = gsm->dlci[address];
 
 	switch (gsm->control) {
@@ -1786,24 +2070,53 @@
 		if (dlci == NULL)
 			return;
 		if (dlci->dead)
-			gsm_response(gsm, address, DM);
+			gsm_response(gsm, address, DM|PF);
 		else {
-			gsm_response(gsm, address, UA);
+			gsm_response(gsm, address, UA|PF);
 			gsm_dlci_open(dlci);
+			/* Save dlci open address */
+			if (address) {
+				addr_open[addr_cnt] = address;
+				addr_cnt++;
+			}
 		}
 		break;
 	case DISC|PF:
 		if (cr == 0)
 			goto invalid;
 		if (dlci == NULL || dlci->state == DLCI_CLOSED) {
-			gsm_response(gsm, address, DM);
+			gsm_response(gsm, address, DM|PF);
 			return;
 		}
 		/* Real close complete */
-		gsm_response(gsm, address, UA);
-		gsm_dlci_close(dlci);
+		if (!address) {
+			if (addr_cnt > 0) {
+				for (i = 0; i < addr_cnt; i++) {
+					address = addr_open[i];
+					dlci = gsm->dlci[address];
+					gsm_dlci_close(dlci);
+					addr_open[i] = 0;
+				}
+			}
+			dlci = gsm->dlci[0];
+			gsm_dlci_close(dlci);
+			addr_cnt = 0;
+			gsm_response(gsm, 0, UA|PF);
+		} else {
+			gsm_response(gsm, address, UA|PF);
+			gsm_dlci_close(dlci);
+			/* clear dlci address */
+			for (j = 0; j < addr_cnt; j++) {
+				address_tmp = addr_open[j];
+				if (address_tmp == address) {
+					for (k = j; k < addr_cnt; k++)
+						addr_open[k] = addr_open[k+1];
+				addr_cnt--;
+				break;
+				}
+			}
+		}
 		break;
-	case UA:
 	case UA|PF:
 		if (cr == 0 || dlci == NULL)
 			break;
@@ -1837,7 +2150,7 @@
 			goto invalid;
 #endif
 		if (dlci == NULL || dlci->state != DLCI_OPEN) {
-			gsm_command(gsm, address, DM|PF);
+			gsm_response(gsm, address, DM|PF);
 			return;
 		}
 		dlci->data(dlci, gsm->buf, gsm->len);
@@ -1851,6 +2164,30 @@
 	return;
 }
 
+/**
+ * gsm0_receive_state_check_and_fix	-	check and correct receive state
+ * @gsm: gsm data for this ldisc instance
+ *
+ * Ensures that the current receive state is valid for basic option mode.
+ */
+
+static void gsm0_receive_state_check_and_fix(struct gsm_mux *gsm)
+{
+	switch (gsm->state) {
+	case GSM_SEARCH:
+	case GSM0_ADDRESS:
+	case GSM0_CONTROL:
+	case GSM0_LEN0:
+	case GSM0_LEN1:
+	case GSM0_DATA:
+	case GSM0_FCS:
+	case GSM0_SSOF:
+		break;
+	default:
+		gsm->state = GSM_SEARCH;
+		break;
+	}
+}
 
 /**
  *	gsm0_receive	-	perform processing for non-transparency
@@ -1864,26 +2201,27 @@
 {
 	unsigned int len;
 
+	gsm0_receive_state_check_and_fix(gsm);
 	switch (gsm->state) {
 	case GSM_SEARCH:	/* SOF marker */
 		if (c == GSM0_SOF) {
-			gsm->state = GSM_ADDRESS;
+			gsm->state = GSM0_ADDRESS;
 			gsm->address = 0;
 			gsm->len = 0;
 			gsm->fcs = INIT_FCS;
 		}
 		break;
-	case GSM_ADDRESS:	/* Address EA */
+	case GSM0_ADDRESS:	/* Address EA */
 		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
 		if (gsm_read_ea(&gsm->address, c))
-			gsm->state = GSM_CONTROL;
+			gsm->state = GSM0_CONTROL;
 		break;
-	case GSM_CONTROL:	/* Control Byte */
+	case GSM0_CONTROL:	/* Control Byte */
 		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
 		gsm->control = c;
-		gsm->state = GSM_LEN0;
+		gsm->state = GSM0_LEN0;
 		break;
-	case GSM_LEN0:		/* Length EA */
+	case GSM0_LEN0:		/* Length EA */
 		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
 		if (gsm_read_ea(&gsm->len, c)) {
 			if (gsm->len > gsm->mru) {
@@ -1893,14 +2231,14 @@
 			}
 			gsm->count = 0;
 			if (!gsm->len)
-				gsm->state = GSM_FCS;
+				gsm->state = GSM0_FCS;
 			else
-				gsm->state = GSM_DATA;
+				gsm->state = GSM0_DATA;
 			break;
 		}
-		gsm->state = GSM_LEN1;
+		gsm->state = GSM0_LEN1;
 		break;
-	case GSM_LEN1:
+	case GSM0_LEN1:
 		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
 		len = c;
 		gsm->len |= len << 7;
@@ -1911,26 +2249,35 @@
 		}
 		gsm->count = 0;
 		if (!gsm->len)
-			gsm->state = GSM_FCS;
+			gsm->state = GSM0_FCS;
 		else
-			gsm->state = GSM_DATA;
+			gsm->state = GSM0_DATA;
 		break;
-	case GSM_DATA:		/* Data */
+	case GSM0_DATA:		/* Data */
 		gsm->buf[gsm->count++] = c;
-		if (gsm->count == gsm->len)
-			gsm->state = GSM_FCS;
-		break;
-	case GSM_FCS:		/* FCS follows the packet */
-		gsm->received_fcs = c;
-		gsm_queue(gsm);
-		gsm->state = GSM_SSOF;
-		break;
-	case GSM_SSOF:
-		if (c == GSM0_SOF) {
+		if (gsm->count >= MAX_MRU) {
+			gsm->bad_size++;
 			gsm->state = GSM_SEARCH;
-			break;
+		} else if (gsm->count >= gsm->len) {
+			/* Calculate final FCS for UI frames over all data */
+			if ((gsm->control & ~PF) != UIH) {
+				gsm->fcs = gsm_fcs_add_block(gsm->fcs, gsm->buf,
+							     gsm->count);
+			}
+			gsm->state = GSM0_FCS;
 		}
 		break;
+	case GSM0_FCS:		/* FCS follows the packet */
+		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
+		gsm->state = GSM0_SSOF;
+		break;
+	case GSM0_SSOF:
+		gsm->state = GSM_SEARCH;
+		if (c == GSM0_SOF)
+			gsm_queue(gsm);
+		else
+			gsm->bad_size++;
+		break;
 	default:
 		pr_debug("%s: unhandled state: %d\n", __func__, gsm->state);
 		break;
@@ -1938,6 +2285,29 @@
 }
 
 /**
+ * gsm1_receive_state_check_and_fix	-	check and correct receive state
+ * @gsm: gsm data for this ldisc instance
+ *
+ * Ensures that the current receive state is valid for advanced option mode.
+ */
+
+static void gsm1_receive_state_check_and_fix(struct gsm_mux *gsm)
+{
+	switch (gsm->state) {
+	case GSM_SEARCH:
+	case GSM1_START:
+	case GSM1_ADDRESS:
+	case GSM1_CONTROL:
+	case GSM1_DATA:
+	case GSM1_OVERRUN:
+		break;
+	default:
+		gsm->state = GSM_SEARCH;
+		break;
+	}
+}
+
+/**
  *	gsm1_receive	-	perform processing for non-transparency
  *	@gsm: gsm data for this ldisc instance
  *	@c: character
@@ -1947,22 +2317,47 @@
 
 static void gsm1_receive(struct gsm_mux *gsm, unsigned char c)
 {
+	gsm1_receive_state_check_and_fix(gsm);
+	/* handle XON/XOFF */
+	if ((c & ISO_IEC_646_MASK) == XON) {
+		gsm->constipated = true;
+		return;
+	} else if ((c & ISO_IEC_646_MASK) == XOFF) {
+		gsm->constipated = false;
+		/* Kick the link in case it is idling */
+		gsm_data_kick(gsm, NULL);
+		return;
+	}
 	if (c == GSM1_SOF) {
-		/* EOF is only valid in frame if we have got to the data state
-		   and received at least one byte (the FCS) */
-		if (gsm->state == GSM_DATA && gsm->count) {
-			/* Extract the FCS */
+		/* EOF is only valid in frame if we have got to the data state */
+		if (gsm->state == GSM1_DATA) {
+			if (gsm->count < 1) {
+				/* Missing FSC */
+				gsm->malformed++;
+				gsm->state = GSM1_START;
+				return;
+			}
+			/* Remove the FCS from data */
 			gsm->count--;
+			if ((gsm->control & ~PF) != UIH) {
+				/* Calculate final FCS for UI frames over all
+				 * data but FCS
+				 */
+				gsm->fcs = gsm_fcs_add_block(gsm->fcs, gsm->buf,
+							     gsm->count);
+			}
+			/* Add the FCS itself to test against GOOD_FCS */
 			gsm->fcs = gsm_fcs_add(gsm->fcs, gsm->buf[gsm->count]);
 			gsm->len = gsm->count;
 			gsm_queue(gsm);
-			gsm->state  = GSM_START;
+			gsm->state  = GSM1_START;
 			return;
 		}
 		/* Any partial frame was a runt so go back to start */
-		if (gsm->state != GSM_START) {
-			gsm->malformed++;
-			gsm->state = GSM_START;
+		if (gsm->state != GSM1_START) {
+			if (gsm->state != GSM_SEARCH)
+				gsm->malformed++;
+			gsm->state = GSM1_START;
 		}
 		/* A SOF in GSM_START means we are still reading idling or
 		   framing bytes */
@@ -1983,30 +2378,30 @@
 		gsm->escape = false;
 	}
 	switch (gsm->state) {
-	case GSM_START:		/* First byte after SOF */
+	case GSM1_START:		/* First byte after SOF */
 		gsm->address = 0;
-		gsm->state = GSM_ADDRESS;
+		gsm->state = GSM1_ADDRESS;
 		gsm->fcs = INIT_FCS;
 		fallthrough;
-	case GSM_ADDRESS:	/* Address continuation */
+	case GSM1_ADDRESS:	/* Address continuation */
 		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
 		if (gsm_read_ea(&gsm->address, c))
-			gsm->state = GSM_CONTROL;
+			gsm->state = GSM1_CONTROL;
 		break;
-	case GSM_CONTROL:	/* Control Byte */
+	case GSM1_CONTROL:	/* Control Byte */
 		gsm->fcs = gsm_fcs_add(gsm->fcs, c);
 		gsm->control = c;
 		gsm->count = 0;
-		gsm->state = GSM_DATA;
+		gsm->state = GSM1_DATA;
 		break;
-	case GSM_DATA:		/* Data */
-		if (gsm->count > gsm->mru) {	/* Allow one for the FCS */
-			gsm->state = GSM_OVERRUN;
+	case GSM1_DATA:		/* Data */
+		if (gsm->count > gsm->mru || gsm->count > MAX_MRU) {	/* Allow one for the FCS */
+			gsm->state = GSM1_OVERRUN;
 			gsm->bad_size++;
 		} else
 			gsm->buf[gsm->count++] = c;
 		break;
-	case GSM_OVERRUN:	/* Over-long - eg a dropped SOF */
+	case GSM1_OVERRUN:	/* Over-long - eg a dropped SOF */
 		break;
 	default:
 		pr_debug("%s: unhandled state: %d\n", __func__, gsm->state);
@@ -2033,74 +2428,49 @@
 	gsm->io_error++;
 }
 
-static int gsm_disconnect(struct gsm_mux *gsm)
-{
-	struct gsm_dlci *dlci = gsm->dlci[0];
-	struct gsm_control *gc;
-
-	if (!dlci)
-		return 0;
-
-	/* In theory disconnecting DLCI 0 is sufficient but for some
-	   modems this is apparently not the case. */
-	gc = gsm_control_send(gsm, CMD_CLD, NULL, 0);
-	if (gc)
-		gsm_control_wait(gsm, gc);
-
-	del_timer_sync(&gsm->t2_timer);
-	/* Now we are sure T2 has stopped */
-
-	gsm_dlci_begin_close(dlci);
-	wait_event_interruptible(gsm->event,
-				dlci->state == DLCI_CLOSED);
-
-	if (signal_pending(current))
-		return -EINTR;
-
-	return 0;
-}
-
 /**
  *	gsm_cleanup_mux		-	generic GSM protocol cleanup
  *	@gsm: our mux
+ *	@disc: disconnect link?
  *
  *	Clean up the bits of the mux which are the same for all framing
  *	protocols. Remove the mux from the mux table, stop all the timers
  *	and then shut down each device hanging up the channels as we go.
  */
 
-static void gsm_cleanup_mux(struct gsm_mux *gsm)
+static void gsm_cleanup_mux(struct gsm_mux *gsm, bool disc)
 {
 	int i;
-	struct gsm_dlci *dlci = gsm->dlci[0];
+	struct gsm_dlci *dlci;
 	struct gsm_msg *txq, *ntxq;
 
 	gsm->dead = true;
+	mutex_lock(&gsm->mutex);
 
-	spin_lock(&gsm_mux_lock);
-	for (i = 0; i < MAX_MUX; i++) {
-		if (gsm_mux[i] == gsm) {
-			gsm_mux[i] = NULL;
-			break;
+	dlci = gsm->dlci[0];
+	if (dlci) {
+		if (disc && dlci->state != DLCI_CLOSED) {
+			gsm_dlci_begin_close(dlci);
+			wait_event(gsm->event, dlci->state == DLCI_CLOSED);
 		}
+		dlci->dead = true;
 	}
-	spin_unlock(&gsm_mux_lock);
-	/* open failed before registering => nothing to do */
-	if (i == MAX_MUX)
-		return;
 
+	/* Finish outstanding timers, making sure they are done */
+	del_timer_sync(&gsm->kick_timer);
 	del_timer_sync(&gsm->t2_timer);
-	/* Now we are sure T2 has stopped */
-	if (dlci)
-		dlci->dead = true;
 
-	/* Free up any link layer users */
-	mutex_lock(&gsm->mutex);
-	for (i = 0; i < NUM_DLCI; i++)
+	/* Free up any link layer users and finally the control channel */
+	if (gsm->has_devices) {
+		gsm_unregister_devices(gsm_tty_driver, gsm->num);
+		gsm->has_devices = false;
+	}
+	for (i = NUM_DLCI - 1; i >= 0; i--)
 		if (gsm->dlci[i])
 			gsm_dlci_release(gsm->dlci[i]);
 	mutex_unlock(&gsm->mutex);
 	/* Now wipe the queues */
+	tty_ldisc_flush(gsm->tty);
 	list_for_each_entry_safe(txq, ntxq, &gsm->tx_list, list)
 		kfree(txq);
 	INIT_LIST_HEAD(&gsm->tx_list);
@@ -2118,8 +2488,13 @@
 static int gsm_activate_mux(struct gsm_mux *gsm)
 {
 	struct gsm_dlci *dlci;
-	int i = 0;
+	int ret;
+
+	dlci = gsm_dlci_alloc(gsm, 0);
+	if (dlci == NULL)
+		return -ENOMEM;
 
+	timer_setup(&gsm->kick_timer, gsm_kick_timer, 0);
 	timer_setup(&gsm->t2_timer, gsm_control_retransmit, 0);
 	init_waitqueue_head(&gsm->event);
 	spin_lock_init(&gsm->control_lock);
@@ -2130,21 +2505,11 @@
 	else
 		gsm->receive = gsm1_receive;
 
-	spin_lock(&gsm_mux_lock);
-	for (i = 0; i < MAX_MUX; i++) {
-		if (gsm_mux[i] == NULL) {
-			gsm->num = i;
-			gsm_mux[i] = gsm;
-			break;
-		}
-	}
-	spin_unlock(&gsm_mux_lock);
-	if (i == MAX_MUX)
-		return -EBUSY;
+	ret = gsm_register_devices(gsm_tty_driver, gsm->num);
+	if (ret)
+		return ret;
 
-	dlci = gsm_dlci_alloc(gsm, 0);
-	if (dlci == NULL)
-		return -ENOMEM;
+	gsm->has_devices = true;
 	gsm->dead = false;		/* Tty opens are now permissible */
 	return 0;
 }
@@ -2157,6 +2522,15 @@
  */
 static void gsm_free_mux(struct gsm_mux *gsm)
 {
+	int i;
+
+	for (i = 0; i < MAX_MUX; i++) {
+		if (gsm == gsm_mux[i]) {
+			gsm_mux[i] = NULL;
+			break;
+		}
+	}
+	mutex_destroy(&gsm->mutex);
 	kfree(gsm->txframe);
 	kfree(gsm->buf);
 	kfree(gsm);
@@ -2176,12 +2550,20 @@
 
 static inline void mux_get(struct gsm_mux *gsm)
 {
+	unsigned long flags;
+
+	spin_lock_irqsave(&gsm_mux_lock, flags);
 	kref_get(&gsm->ref);
+	spin_unlock_irqrestore(&gsm_mux_lock, flags);
 }
 
 static inline void mux_put(struct gsm_mux *gsm)
 {
+	unsigned long flags;
+
+	spin_lock_irqsave(&gsm_mux_lock, flags);
 	kref_put(&gsm->ref, gsm_free_muxr);
+	spin_unlock_irqrestore(&gsm_mux_lock, flags);
 }
 
 static inline unsigned int mux_num_to_base(struct gsm_mux *gsm)
@@ -2202,6 +2584,7 @@
 
 static struct gsm_mux *gsm_alloc_mux(void)
 {
+	int i;
 	struct gsm_mux *gsm = kzalloc(sizeof(struct gsm_mux), GFP_KERNEL);
 	if (gsm == NULL)
 		return NULL;
@@ -2210,7 +2593,7 @@
 		kfree(gsm);
 		return NULL;
 	}
-	gsm->txframe = kmalloc(2 * MAX_MRU + 2, GFP_KERNEL);
+	gsm->txframe = kmalloc(2 * (MAX_MTU + PROT_OVERHEAD - 1), GFP_KERNEL);
 	if (gsm->txframe == NULL) {
 		kfree(gsm->buf);
 		kfree(gsm);
@@ -2231,6 +2614,26 @@
 	gsm->mtu = 64;
 	gsm->dead = true;	/* Avoid early tty opens */
 
+	/* Store the instance to the mux array or abort if no space is
+	 * available.
+	 */
+	spin_lock(&gsm_mux_lock);
+	for (i = 0; i < MAX_MUX; i++) {
+		if (!gsm_mux[i]) {
+			gsm_mux[i] = gsm;
+			gsm->num = i;
+			break;
+		}
+	}
+	spin_unlock(&gsm_mux_lock);
+	if (i == MAX_MUX) {
+		mutex_destroy(&gsm->mutex);
+		kfree(gsm->txframe);
+		kfree(gsm->buf);
+		kfree(gsm);
+		return NULL;
+	}
+
 	return gsm;
 }
 
@@ -2257,6 +2660,7 @@
 
 static int gsm_config(struct gsm_mux *gsm, struct gsm_config *c)
 {
+	int ret = 0;
 	int need_close = 0;
 	int need_restart = 0;
 
@@ -2266,7 +2670,7 @@
 	/* Check the MRU/MTU range looks sane */
 	if (c->mru > MAX_MRU || c->mtu > MAX_MTU || c->mru < 8 || c->mtu < 8)
 		return -EINVAL;
-	if (c->n2 < 3)
+	if (c->n2 > 255)
 		return -EINVAL;
 	if (c->encapsulation > 1)	/* Basic, advanced, no I */
 		return -EINVAL;
@@ -2297,19 +2701,11 @@
 
 	/*
 	 * Close down what is needed, restart and initiate the new
-	 * configuration
+	 * configuration. On the first time there is no DLCI[0]
+	 * and closing or cleaning up is not necessary.
 	 */
-
-	if (need_close || need_restart) {
-		int ret;
-
-		ret = gsm_disconnect(gsm);
-
-		if (ret)
-			return ret;
-	}
-	if (need_restart)
-		gsm_cleanup_mux(gsm);
+	if (need_close || need_restart)
+		gsm_cleanup_mux(gsm, true);
 
 	gsm->initiator = c->initiator;
 	gsm->mru = c->mru;
@@ -2332,10 +2728,13 @@
 	 * FIXME: We need to separate activation/deactivation from adding
 	 * and removing from the mux array
 	 */
-	if (need_restart)
-		gsm_activate_mux(gsm);
-	if (gsm->initiator && need_close)
-		gsm_dlci_begin_open(gsm->dlci[0]);
+	if (gsm->dead) {
+		ret = gsm_activate_mux(gsm);
+		if (ret)
+			return ret;
+		if (gsm->initiator)
+			gsm_dlci_begin_open(gsm->dlci[0]);
+	}
 	return 0;
 }
 
@@ -2356,10 +2755,8 @@
 		return -ENOSPC;
 	}
 	if (debug & 4)
-		print_hex_dump_bytes("gsmld_output: ", DUMP_PREFIX_OFFSET,
-				     data, len);
-	gsm->tty->ops->write(gsm->tty, data, len);
-	return len;
+		gsm_hex_dump_bytes(__func__, data, len);
+	return gsm->tty->ops->write(gsm->tty, data, len);
 }
 
 /**
@@ -2372,36 +2769,14 @@
  *	will need moving to an ioctl path.
  */
 
-static int gsmld_attach_gsm(struct tty_struct *tty, struct gsm_mux *gsm)
+static void gsmld_attach_gsm(struct tty_struct *tty, struct gsm_mux *gsm)
 {
-	unsigned int base;
-	int ret, i;
-
 	gsm->tty = tty_kref_get(tty);
-	ret =  gsm_activate_mux(gsm);
-	if (ret != 0)
-		tty_kref_put(gsm->tty);
-	else {
-		/* Don't register device 0 - this is the control channel and not
-		   a usable tty interface */
-		base = mux_num_to_base(gsm); /* Base for this MUX */
-		for (i = 1; i < NUM_DLCI; i++) {
-			struct device *dev;
-
-			dev = tty_register_device(gsm_tty_driver,
-							base + i, NULL);
-			if (IS_ERR(dev)) {
-				for (i--; i >= 1; i--)
-					tty_unregister_device(gsm_tty_driver,
-								base + i);
-				return PTR_ERR(dev);
-			}
-		}
-	}
-	return ret;
+	/* Turn off tty XON/XOFF handling to handle it explicitly. */
+	gsm->old_c_iflag = tty->termios.c_iflag;
+	tty->termios.c_iflag &= (IXON | IXOFF);
 }
 
-
 /**
  *	gsmld_detach_gsm	-	stop doing 0710 mux
  *	@tty: tty attached to the mux
@@ -2412,13 +2787,9 @@
 
 static void gsmld_detach_gsm(struct tty_struct *tty, struct gsm_mux *gsm)
 {
-	unsigned int base = mux_num_to_base(gsm); /* Base for this MUX */
-	int i;
-
 	WARN_ON(tty != gsm->tty);
-	for (i = 1; i < NUM_DLCI; i++)
-		tty_unregister_device(gsm_tty_driver, base + i);
-	gsm_cleanup_mux(gsm);
+	/* Restore tty XON/XOFF handling. */
+	gsm->tty->termios.c_iflag = gsm->old_c_iflag;
 	tty_kref_put(gsm->tty);
 	gsm->tty = NULL;
 }
@@ -2430,15 +2801,15 @@
 	char flags = TTY_NORMAL;
 
 	if (debug & 4)
-		print_hex_dump_bytes("gsmld_receive: ", DUMP_PREFIX_OFFSET,
-				     cp, count);
+		gsm_hex_dump_bytes(__func__, cp, count);
 
 	for (; count; count--, cp++) {
 		if (fp)
 			flags = *fp++;
 		switch (flags) {
 		case TTY_NORMAL:
-			gsm->receive(gsm, *cp);
+			if (gsm->receive)
+				gsm->receive(gsm, *cp);
 			break;
 		case TTY_OVERRUN:
 		case TTY_BREAK:
@@ -2483,6 +2854,12 @@
 {
 	struct gsm_mux *gsm = tty->disc_data;
 
+	/* The ldisc locks and closes the port before calling our close. This
+	 * means we have no way to do a proper disconnect. We will not bother
+	 * to do one.
+	 */
+	gsm_cleanup_mux(gsm, false);
+
 	gsmld_detach_gsm(tty, gsm);
 
 	gsmld_flush_buffer(tty);
@@ -2503,7 +2880,9 @@
 static int gsmld_open(struct tty_struct *tty)
 {
 	struct gsm_mux *gsm;
-	int ret;
+
+	if (!capable(CAP_NET_ADMIN))
+		return -EPERM;
 
 	if (tty->ops->write == NULL)
 		return -EINVAL;
@@ -2519,12 +2898,12 @@
 	/* Attach the initial passive connection */
 	gsm->encoding = 1;
 
-	ret = gsmld_attach_gsm(tty, gsm);
-	if (ret != 0) {
-		gsm_cleanup_mux(gsm);
-		mux_put(gsm);
-	}
-	return ret;
+	gsmld_attach_gsm(tty, gsm);
+
+	timer_setup(&gsm->kick_timer, gsm_kick_timer, 0);
+	timer_setup(&gsm->t2_timer, gsm_control_retransmit, 0);
+
+	return 0;
 }
 
 /**
@@ -2592,11 +2971,24 @@
 static ssize_t gsmld_write(struct tty_struct *tty, struct file *file,
 			   const unsigned char *buf, size_t nr)
 {
-	int space = tty_write_room(tty);
+	struct gsm_mux *gsm = tty->disc_data;
+	unsigned long flags;
+	int space;
+	int ret;
+
+	if (!gsm)
+		return -ENODEV;
+
+	ret = -ENOBUFS;
+	spin_lock_irqsave(&gsm->tx_lock, flags);
+	space = tty_write_room(tty);
 	if (space >= nr)
-		return tty->ops->write(tty, buf, nr);
-	set_bit(TTY_DO_WRITE_WAKEUP, &tty->flags);
-	return -ENOBUFS;
+		ret = tty->ops->write(tty, buf, nr);
+	else
+		set_bit(TTY_DO_WRITE_WAKEUP, &tty->flags);
+	spin_unlock_irqrestore(&gsm->tx_lock, flags);
+
+	return ret;
 }
 
 /**
@@ -2621,12 +3013,15 @@
 
 	poll_wait(file, &tty->read_wait, wait);
 	poll_wait(file, &tty->write_wait, wait);
+
+	if (gsm->dead)
+		mask |= EPOLLHUP;
 	if (tty_hung_up_p(file))
 		mask |= EPOLLHUP;
+	if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
+		mask |= EPOLLHUP;
 	if (!tty_is_writelocked(tty) && tty_write_room(tty) > 0)
 		mask |= EPOLLOUT | EPOLLWRNORM;
-	if (gsm->dead)
-		mask |= EPOLLHUP;
 	return mask;
 }
 
@@ -2876,28 +3271,80 @@
  *	Virtual tty side
  */
 
-#define TX_SIZE		512
+/**
+ *	gsm_modem_upd_via_data	-	send modem bits via convergence layer
+ *	@dlci: channel
+ *	@brk: break signal
+ *
+ *	Send an empty frame to signal mobile state changes and to transmit the
+ *	break signal for adaption 2.
+ */
+
+static void gsm_modem_upd_via_data(struct gsm_dlci *dlci, u8 brk)
+{
+	struct gsm_mux *gsm = dlci->gsm;
+	unsigned long flags;
+
+	if (dlci->state != DLCI_OPEN || dlci->adaption != 2)
+		return;
+
+	spin_lock_irqsave(&gsm->tx_lock, flags);
+	gsm_dlci_modem_output(gsm, dlci, brk);
+	spin_unlock_irqrestore(&gsm->tx_lock, flags);
+}
+
+/**
+ *	gsm_modem_upd_via_msc	-	send modem bits via control frame
+ *	@dlci: channel
+ *	@brk: break signal
+ */
 
-static int gsmtty_modem_update(struct gsm_dlci *dlci, u8 brk)
+static int gsm_modem_upd_via_msc(struct gsm_dlci *dlci, u8 brk)
 {
-	u8 modembits[5];
+	u8 modembits[3];
 	struct gsm_control *ctrl;
 	int len = 2;
 
-	if (brk)
-		len++;
+	if (dlci->gsm->encoding != 0)
+		return 0;
 
-	modembits[0] = len << 1 | EA;		/* Data bytes */
-	modembits[1] = dlci->addr << 2 | 3;	/* DLCI, EA, 1 */
-	modembits[2] = gsm_encode_modem(dlci) << 1 | EA;
-	if (brk)
-		modembits[3] = brk << 4 | 2 | EA;	/* Valid, EA */
-	ctrl = gsm_control_send(dlci->gsm, CMD_MSC, modembits, len + 1);
+	modembits[0] = (dlci->addr << 2) | 2 | EA;  /* DLCI, Valid, EA */
+	if (!brk) {
+		modembits[1] = (gsm_encode_modem(dlci) << 1) | EA;
+	} else {
+		modembits[1] = gsm_encode_modem(dlci) << 1;
+		modembits[2] = (brk << 4) | 2 | EA; /* Length, Break, EA */
+		len++;
+	}
+	ctrl = gsm_control_send(dlci->gsm, CMD_MSC, modembits, len);
 	if (ctrl == NULL)
 		return -ENOMEM;
 	return gsm_control_wait(dlci->gsm, ctrl);
 }
 
+/**
+ *	gsm_modem_update	-	send modem status line state
+ *	@dlci: channel
+ *	@brk: break signal
+ */
+
+static int gsm_modem_update(struct gsm_dlci *dlci, u8 brk)
+{
+	if (dlci->gsm->dead)
+		return -EL2HLT;
+	if (dlci->adaption == 2) {
+		/* Send convergence layer type 2 empty data frame. */
+		gsm_modem_upd_via_data(dlci, brk);
+		return 0;
+	} else if (dlci->gsm->encoding == 0) {
+		/* Send as MSC control message. */
+		return gsm_modem_upd_via_msc(dlci, brk);
+	}
+
+	/* Modem status lines are not supported. */
+	return -EPROTONOSUPPORT;
+}
+
 static int gsm_carrier_raised(struct tty_port *port)
 {
 	struct gsm_dlci *dlci = container_of(port, struct gsm_dlci, port);
@@ -2930,7 +3377,7 @@
 		modem_tx &= ~(TIOCM_DTR | TIOCM_RTS);
 	if (modem_tx != dlci->modem_tx) {
 		dlci->modem_tx = modem_tx;
-		gsmtty_modem_update(dlci, 0);
+		gsm_modem_update(dlci, 0);
 	}
 }
 
@@ -3000,6 +3447,7 @@
 {
 	struct gsm_dlci *dlci = tty->driver_data;
 	struct tty_port *port = &dlci->port;
+	struct gsm_mux *gsm = dlci->gsm;
 
 	port->count++;
 	tty_port_tty_set(port, tty);
@@ -3009,7 +3457,10 @@
 	   a DM straight back. This is ok as that will have caused a hangup */
 	tty_port_set_initialized(port, 1);
 	/* Start sending off SABM messages */
-	gsm_dlci_begin_open(dlci);
+	if (gsm->initiator)
+		gsm_dlci_begin_open(dlci);
+	else
+		gsm_dlci_set_opening(dlci);
 	/* And wait for virtual carrier */
 	return tty_port_block_til_ready(port, tty, filp);
 }
@@ -3063,7 +3514,7 @@
 	struct gsm_dlci *dlci = tty->driver_data;
 	if (dlci->state == DLCI_CLOSED)
 		return 0;
-	return TX_SIZE - kfifo_len(&dlci->fifo);
+	return kfifo_avail(&dlci->fifo);
 }
 
 static unsigned int gsmtty_chars_in_buffer(struct tty_struct *tty)
@@ -3077,13 +3528,17 @@
 static void gsmtty_flush_buffer(struct tty_struct *tty)
 {
 	struct gsm_dlci *dlci = tty->driver_data;
+	unsigned long flags;
+
 	if (dlci->state == DLCI_CLOSED)
 		return;
 	/* Caution needed: If we implement reliable transport classes
 	   then the data being transmitted can't simply be junked once
 	   it has first hit the stack. Until then we can just blow it
 	   away */
+	spin_lock_irqsave(&dlci->lock, flags);
 	kfifo_reset(&dlci->fifo);
+	spin_unlock_irqrestore(&dlci->lock, flags);
 	/* Need to unhook this DLCI from the transmit queue logic */
 }
 
@@ -3115,7 +3570,7 @@
 
 	if (modem_tx != dlci->modem_tx) {
 		dlci->modem_tx = modem_tx;
-		return gsmtty_modem_update(dlci, 0);
+		return gsm_modem_update(dlci, 0);
 	}
 	return 0;
 }
@@ -3173,10 +3628,10 @@
 	if (dlci->state == DLCI_CLOSED)
 		return;
 	if (C_CRTSCTS(tty))
-		dlci->modem_tx &= ~TIOCM_DTR;
+		dlci->modem_tx &= ~TIOCM_RTS;
 	dlci->throttled = true;
-	/* Send an MSC with DTR cleared */
-	gsmtty_modem_update(dlci, 0);
+	/* Send an MSC with RTS cleared */
+	gsm_modem_update(dlci, 0);
 }
 
 static void gsmtty_unthrottle(struct tty_struct *tty)
@@ -3185,10 +3640,10 @@
 	if (dlci->state == DLCI_CLOSED)
 		return;
 	if (C_CRTSCTS(tty))
-		dlci->modem_tx |= TIOCM_DTR;
+		dlci->modem_tx |= TIOCM_RTS;
 	dlci->throttled = false;
-	/* Send an MSC with DTR set */
-	gsmtty_modem_update(dlci, 0);
+	/* Send an MSC with RTS set */
+	gsm_modem_update(dlci, 0);
 }
 
 static int gsmtty_break_ctl(struct tty_struct *tty, int state)
@@ -3206,7 +3661,7 @@
 		if (encode > 0x0F)
 			encode = 0x0F;	/* Best effort */
 	}
-	return gsmtty_modem_update(dlci, encode);
+	return gsm_modem_update(dlci, encode);
 }
 
 static void gsmtty_cleanup(struct tty_struct *tty)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/n_hdlc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/n_hdlc.c
@@ -140,6 +140,8 @@
 	struct n_hdlc_buf_list	rx_buf_list;
 	struct n_hdlc_buf_list	tx_free_buf_list;
 	struct n_hdlc_buf_list	rx_free_buf_list;
+	struct work_struct	write_work;
+	struct tty_struct	*tty_for_write_work;
 };
 
 /*
@@ -154,6 +156,7 @@
 /* Local functions */
 
 static struct n_hdlc *n_hdlc_alloc(void);
+static void n_hdlc_tty_write_work(struct work_struct *work);
 
 /* max frame size for memory allocations */
 static int maxframe = 4096;
@@ -210,6 +213,8 @@
 	wake_up_interruptible(&tty->read_wait);
 	wake_up_interruptible(&tty->write_wait);
 
+	cancel_work_sync(&n_hdlc->write_work);
+
 	n_hdlc_free_buf_list(&n_hdlc->rx_free_buf_list);
 	n_hdlc_free_buf_list(&n_hdlc->tx_free_buf_list);
 	n_hdlc_free_buf_list(&n_hdlc->rx_buf_list);
@@ -241,6 +246,8 @@
 		return -ENFILE;
 	}
 
+	INIT_WORK(&n_hdlc->write_work, n_hdlc_tty_write_work);
+	n_hdlc->tty_for_write_work = tty;
 	tty->disc_data = n_hdlc;
 	tty->receive_room = 65536;
 
@@ -335,6 +342,20 @@
 }	/* end of n_hdlc_send_frames() */
 
 /**
+ * n_hdlc_tty_write_work - Asynchronous callback for transmit wakeup
+ * @work: pointer to work_struct
+ *
+ * Called when low level device driver can accept more send data.
+ */
+static void n_hdlc_tty_write_work(struct work_struct *work)
+{
+	struct n_hdlc *n_hdlc = container_of(work, struct n_hdlc, write_work);
+	struct tty_struct *tty = n_hdlc->tty_for_write_work;
+
+	n_hdlc_send_frames(n_hdlc, tty);
+}	/* end of n_hdlc_tty_write_work() */
+
+/**
  * n_hdlc_tty_wakeup - Callback for transmit wakeup
  * @tty: pointer to associated tty instance data
  *
@@ -344,7 +365,7 @@
 {
 	struct n_hdlc *n_hdlc = tty->disc_data;
 
-	n_hdlc_send_frames(n_hdlc, tty);
+	schedule_work(&n_hdlc->write_work);
 }	/* end of n_hdlc_tty_wakeup() */
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/n_tty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/n_tty.c
@@ -202,8 +202,8 @@
 	struct n_tty_data *ldata = tty->disc_data;
 
 	/* Did the input worker stop? Restart it */
-	if (unlikely(ldata->no_room)) {
-		ldata->no_room = 0;
+	if (unlikely(READ_ONCE(ldata->no_room))) {
+		WRITE_ONCE(ldata->no_room, 0);
 
 		WARN_RATELIMIT(tty->port->itty == NULL,
 				"scheduling with invalid itty\n");
@@ -1369,7 +1369,7 @@
 			put_tty_queue(c, ldata);
 			smp_store_release(&ldata->canon_head, ldata->read_head);
 			kill_fasync(&tty->fasync, SIGIO, POLL_IN);
-			wake_up_interruptible_poll(&tty->read_wait, EPOLLIN);
+			wake_up_interruptible_poll(&tty->read_wait, EPOLLIN | EPOLLRDNORM);
 			return;
 		}
 	}
@@ -1589,7 +1589,7 @@
 
 	if (read_cnt(ldata)) {
 		kill_fasync(&tty->fasync, SIGIO, POLL_IN);
-		wake_up_interruptible_poll(&tty->read_wait, EPOLLIN);
+		wake_up_interruptible_poll(&tty->read_wait, EPOLLIN | EPOLLRDNORM);
 	}
 }
 
@@ -1661,7 +1661,7 @@
 			if (overflow && room < 0)
 				ldata->read_head--;
 			room = overflow;
-			ldata->no_room = flow && !room;
+			WRITE_ONCE(ldata->no_room, flow && !room);
 		} else
 			overflow = 0;
 
@@ -1692,6 +1692,17 @@
 	} else
 		n_tty_check_throttle(tty);
 
+	if (unlikely(ldata->no_room)) {
+		/*
+		 * Barrier here is to ensure to read the latest read_tail in
+		 * chars_in_buffer() and to make sure that read_tail is not loaded
+		 * before ldata->no_room is set.
+		 */
+		smp_mb();
+		if (!chars_in_buffer(tty))
+			n_tty_kick_worker(tty);
+	}
+
 	up_read(&tty->termios_rwsem);
 
 	return rcvd;
@@ -1963,7 +1974,7 @@
 		return false;
 
 	canon_head = smp_load_acquire(&ldata->canon_head);
-	n = min(*nr + 1, canon_head - ldata->read_tail);
+	n = min(*nr, canon_head - ldata->read_tail);
 
 	tail = ldata->read_tail & (N_TTY_BUF_SIZE - 1);
 	size = min_t(size_t, tail + n, N_TTY_BUF_SIZE);
@@ -1985,10 +1996,8 @@
 		n += N_TTY_BUF_SIZE;
 	c = n + found;
 
-	if (!found || read_buf(ldata, eol) != __DISABLED_CHAR) {
-		c = min(*nr, c);
+	if (!found || read_buf(ldata, eol) != __DISABLED_CHAR)
 		n = c;
-	}
 
 	n_tty_trace("%s: eol:%zu found:%d n:%zu c:%zu tail:%zu more:%zu\n",
 		    __func__, eol, found, n, c, tail, more);
@@ -2014,6 +2023,35 @@
 	return ldata->read_tail != canon_head;
 }
 
+/*
+ * If we finished a read at the exact location of an
+ * EOF (special EOL character that's a __DISABLED_CHAR)
+ * in the stream, silently eat the EOF.
+ */
+static void canon_skip_eof(struct tty_struct *tty)
+{
+	struct n_tty_data *ldata = tty->disc_data;
+	size_t tail, canon_head;
+
+	canon_head = smp_load_acquire(&ldata->canon_head);
+	tail = ldata->read_tail;
+
+	// No data?
+	if (tail == canon_head)
+		return;
+
+	// See if the tail position is EOF in the circular buffer
+	tail &= (N_TTY_BUF_SIZE - 1);
+	if (!test_bit(tail, ldata->read_flags))
+		return;
+	if (read_buf(ldata, tail) != __DISABLED_CHAR)
+		return;
+
+	// Clear the EOL bit, skip the EOF char.
+	clear_bit(tail, ldata->read_flags);
+	smp_store_release(&ldata->read_tail, ldata->read_tail + 1);
+}
+
 /**
  *	job_control		-	check job control
  *	@tty: tty
@@ -2073,7 +2111,7 @@
 	ssize_t retval = 0;
 	long timeout;
 	bool packet;
-	size_t tail;
+	size_t old_tail;
 
 	/*
 	 * Is this a continuation of a read started earler?
@@ -2083,7 +2121,14 @@
 	 */
 	if (*cookie) {
 		if (ldata->icanon && !L_EXTPROC(tty)) {
-			if (canon_copy_from_read_buf(tty, &kb, &nr))
+			/*
+			 * If we have filled the user buffer, see
+			 * if we should skip an EOF character before
+			 * releasing the lock and returning done.
+			 */
+			if (!nr)
+				canon_skip_eof(tty);
+			else if (canon_copy_from_read_buf(tty, &kb, &nr))
 				return kb - kbuf;
 		} else {
 			if (copy_from_read_buf(tty, &kb, &nr))
@@ -2129,7 +2174,7 @@
 	}
 
 	packet = tty->ctrl.packet;
-	tail = ldata->read_tail;
+	old_tail = ldata->read_tail;
 
 	add_wait_queue(&tty->read_wait, &wait);
 	while (nr) {
@@ -2218,8 +2263,14 @@
 		if (time)
 			timeout = time;
 	}
-	if (tail != ldata->read_tail)
+	if (old_tail != ldata->read_tail) {
+		/*
+		 * Make sure no_room is not read in n_tty_kick_worker()
+		 * before setting ldata->read_tail in copy_from_read_buf().
+		 */
+		smp_mb();
 		n_tty_kick_worker(tty);
+	}
 	up_read(&tty->termios_rwsem);
 
 	remove_wait_queue(&tty->read_wait, &wait);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/pty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/pty.c
@@ -111,21 +111,11 @@
 static int pty_write(struct tty_struct *tty, const unsigned char *buf, int c)
 {
 	struct tty_struct *to = tty->link;
-	unsigned long flags;
 
-	if (tty->flow.stopped)
+	if (tty->flow.stopped || !c)
 		return 0;
 
-	if (c > 0) {
-		spin_lock_irqsave(&to->port->lock, flags);
-		/* Stuff the data into the input queue of the other end */
-		c = tty_insert_flip_string(to->port, buf, c);
-		spin_unlock_irqrestore(&to->port->lock, flags);
-		/* And shovel */
-		if (c)
-			tty_flip_buffer_push(to->port);
-	}
-	return c;
+	return tty_insert_flip_string_and_push_buffer(to->port, buf, c);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250.h
@@ -17,6 +17,8 @@
 struct uart_8250_dma {
 	int (*tx_dma)(struct uart_8250_port *p);
 	int (*rx_dma)(struct uart_8250_port *p);
+	void (*prepare_tx_dma)(struct uart_8250_port *p);
+	void (*prepare_rx_dma)(struct uart_8250_port *p);
 
 	/* Filter function */
 	dma_filter_fn		fn;
@@ -88,7 +90,6 @@
 #define UART_BUG_TXEN	BIT(1)	/* UART has buggy TX IIR status */
 #define UART_BUG_NOMSR	BIT(2)	/* UART has buggy MSR status bits (Au1x00) */
 #define UART_BUG_THRE	BIT(3)	/* UART has buggy THRE reassertion */
-#define UART_BUG_PARITY	BIT(4)	/* UART mishandles parity if FIFO enabled */
 #define UART_BUG_TXRACE	BIT(5)	/* UART Tx fails to set remote DR */
 
 
@@ -120,6 +121,28 @@
 	up->port.serial_out(&up->port, offset, value);
 }
 
+/*
+ * For the 16C950
+ */
+static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
+{
+	serial_out(up, UART_SCR, offset);
+	serial_out(up, UART_ICR, value);
+}
+
+static unsigned int __maybe_unused serial_icr_read(struct uart_8250_port *up,
+						   int offset)
+{
+	unsigned int value;
+
+	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
+	serial_out(up, UART_SCR, offset);
+	value = serial_in(up, UART_ICR);
+	serial_icr_write(up, UART_ACR, up->acr);
+
+	return value;
+}
+
 void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p);
 
 static inline int serial_dl_read(struct uart_8250_port *up)
@@ -158,7 +181,8 @@
 void serial8250_rpm_get_tx(struct uart_8250_port *p);
 void serial8250_rpm_put_tx(struct uart_8250_port *p);
 
-int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485);
+int serial8250_em485_config(struct uart_port *port, struct ktermios *termios,
+			    struct serial_rs485 *rs485);
 void serial8250_em485_start_tx(struct uart_8250_port *p);
 void serial8250_em485_stop_tx(struct uart_8250_port *p);
 void serial8250_em485_destroy(struct uart_8250_port *p);
@@ -305,15 +329,40 @@
 
 #ifdef CONFIG_SERIAL_8250_DMA
 extern int serial8250_tx_dma(struct uart_8250_port *);
+extern void serial8250_tx_dma_flush(struct uart_8250_port *);
 extern int serial8250_rx_dma(struct uart_8250_port *);
 extern void serial8250_rx_dma_flush(struct uart_8250_port *);
 extern int serial8250_request_dma(struct uart_8250_port *);
 extern void serial8250_release_dma(struct uart_8250_port *);
+
+static inline void serial8250_do_prepare_tx_dma(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	if (dma->prepare_tx_dma)
+		dma->prepare_tx_dma(p);
+}
+
+static inline void serial8250_do_prepare_rx_dma(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	if (dma->prepare_rx_dma)
+		dma->prepare_rx_dma(p);
+}
+
+static inline bool serial8250_tx_dma_running(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	return dma && dma->tx_running;
+}
 #else
 static inline int serial8250_tx_dma(struct uart_8250_port *p)
 {
 	return -1;
 }
+static inline void serial8250_tx_dma_flush(struct uart_8250_port *p) { }
 static inline int serial8250_rx_dma(struct uart_8250_port *p)
 {
 	return -1;
@@ -324,6 +373,11 @@
 	return -1;
 }
 static inline void serial8250_release_dma(struct uart_8250_port *p) { }
+
+static inline bool serial8250_tx_dma_running(struct uart_8250_port *p)
+{
+	return false;
+}
 #endif
 
 static inline int ns16550a_goto_highspeed(struct uart_8250_port *up)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_aspeed_vuart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_aspeed_vuart.c
@@ -429,6 +429,8 @@
 	timer_setup(&vuart->unthrottle_timer, aspeed_vuart_unthrottle_exp, 0);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
 
 	memset(&port, 0, sizeof(port));
 	port.port.private_data = vuart;
@@ -487,7 +489,7 @@
 	port.port.irq = irq_of_parse_and_map(np, 0);
 	port.port.handle_irq = aspeed_vuart_handle_irq;
 	port.port.iotype = UPIO_MEM;
-	port.port.type = PORT_16550A;
+	port.port.type = PORT_ASPEED_VUART;
 	port.port.uartclk = clk;
 	port.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
 		| UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_NO_THRE_TEST;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_bcm7271.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_bcm7271.c
@@ -237,6 +237,7 @@
 	u32		rx_err;
 	u32		rx_timeout;
 	u32		rx_abort;
+	u32		saved_mctrl;
 };
 
 static struct dentry *brcmuart_debugfs_root;
@@ -673,18 +674,46 @@
 	clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate);
 }
 
+static u32 find_quot(struct device *dev, u32 freq, u32 baud, u32 *percent)
+{
+	u32 quot;
+	u32 rate;
+	u64 hires_rate;
+	u64 hires_baud;
+	u64 hires_err;
+
+	rate = freq / 16;
+	quot = DIV_ROUND_CLOSEST(rate, baud);
+	if (!quot)
+		return 0;
+
+	/* increase resolution to get xx.xx percent */
+	hires_rate = div_u64((u64)rate * 10000, (u64)quot);
+	hires_baud = (u64)baud * 10000;
+
+	/* get the delta */
+	if (hires_rate > hires_baud)
+		hires_err = (hires_rate - hires_baud);
+	else
+		hires_err = (hires_baud - hires_rate);
+
+	*percent = (unsigned long)DIV_ROUND_CLOSEST_ULL(hires_err, baud);
+
+	dev_dbg(dev, "Baud rate: %u, MUX Clk: %u, Error: %u.%u%%\n",
+		baud, freq, *percent / 100, *percent % 100);
+
+	return quot;
+}
+
 static void set_clock_mux(struct uart_port *up, struct brcmuart_priv *priv,
 			u32 baud)
 {
 	u32 percent;
 	u32 best_percent = UINT_MAX;
 	u32 quot;
+	u32 freq;
 	u32 best_quot = 1;
-	u32 rate;
-	int best_index = -1;
-	u64 hires_rate;
-	u64 hires_baud;
-	u64 hires_err;
+	u32 best_freq = 0;
 	int rc;
 	int i;
 	int real_baud;
@@ -693,44 +722,35 @@
 	if (priv->baud_mux_clk == NULL)
 		return;
 
-	/* Find the closest match for specified baud */
-	for (i = 0; i < ARRAY_SIZE(priv->real_rates); i++) {
-		if (priv->real_rates[i] == 0)
-			continue;
-		rate = priv->real_rates[i] / 16;
-		quot = DIV_ROUND_CLOSEST(rate, baud);
-		if (!quot)
-			continue;
-
-		/* increase resolution to get xx.xx percent */
-		hires_rate = (u64)rate * 10000;
-		hires_baud = (u64)baud * 10000;
-
-		hires_err = div_u64(hires_rate, (u64)quot);
-
-		/* get the delta */
-		if (hires_err > hires_baud)
-			hires_err = (hires_err - hires_baud);
-		else
-			hires_err = (hires_baud - hires_err);
-
-		percent = (unsigned long)DIV_ROUND_CLOSEST_ULL(hires_err, baud);
-		dev_dbg(up->dev,
-			"Baud rate: %u, MUX Clk: %u, Error: %u.%u%%\n",
-			baud, priv->real_rates[i], percent / 100,
-			percent % 100);
-		if (percent < best_percent) {
-			best_percent = percent;
-			best_index = i;
-			best_quot = quot;
+	/* Try default_mux_rate first */
+	quot = find_quot(up->dev, priv->default_mux_rate, baud, &percent);
+	if (quot) {
+		best_percent = percent;
+		best_freq = priv->default_mux_rate;
+		best_quot = quot;
+	}
+	/* If more than 1% error, find the closest match for specified baud */
+	if (best_percent > 100) {
+		for (i = 0; i < ARRAY_SIZE(priv->real_rates); i++) {
+			freq = priv->real_rates[i];
+			if (freq == 0 || freq == priv->default_mux_rate)
+				continue;
+			quot = find_quot(up->dev, freq, baud, &percent);
+			if (!quot)
+				continue;
+
+			if (percent < best_percent) {
+				best_percent = percent;
+				best_freq = freq;
+				best_quot = quot;
+			}
 		}
 	}
-	if (best_index == -1) {
+	if (!best_freq) {
 		dev_err(up->dev, "Error, %d BAUD rate is too fast.\n", baud);
 		return;
 	}
-	rate = priv->real_rates[best_index];
-	rc = clk_set_rate(priv->baud_mux_clk, rate);
+	rc = clk_set_rate(priv->baud_mux_clk, best_freq);
 	if (rc)
 		dev_err(up->dev, "Error selecting BAUD MUX clock\n");
 
@@ -739,8 +759,8 @@
 		dev_err(up->dev, "Error, baud: %d has %u.%u%% error\n",
 			baud, percent / 100, percent % 100);
 
-	real_baud = rate / 16 / best_quot;
-	dev_dbg(up->dev, "Selecting BAUD MUX rate: %u\n", rate);
+	real_baud = best_freq / 16 / best_quot;
+	dev_dbg(up->dev, "Selecting BAUD MUX rate: %u\n", best_freq);
 	dev_dbg(up->dev, "Requested baud: %u, Actual baud: %u\n",
 		baud, real_baud);
 
@@ -749,7 +769,7 @@
 	i += (i / 2);
 	priv->char_wait = ns_to_ktime(i);
 
-	up->uartclk = rate;
+	up->uartclk = best_freq;
 }
 
 static void brcmstb_set_termios(struct uart_port *up,
@@ -1015,16 +1035,18 @@
 	of_property_read_u32(np, "clock-frequency", &clk_rate);
 
 	/* See if a Baud clock has been specified */
-	baud_mux_clk = of_clk_get_by_name(np, "sw_baud");
+	baud_mux_clk = devm_clk_get(dev, "sw_baud");
 	if (IS_ERR(baud_mux_clk)) {
-		if (PTR_ERR(baud_mux_clk) == -EPROBE_DEFER)
-			return -EPROBE_DEFER;
+		if (PTR_ERR(baud_mux_clk) == -EPROBE_DEFER) {
+			ret = -EPROBE_DEFER;
+			goto release_dma;
+		}
 		dev_dbg(dev, "BAUD MUX clock not specified\n");
 	} else {
 		dev_dbg(dev, "BAUD MUX clock found\n");
 		ret = clk_prepare_enable(baud_mux_clk);
 		if (ret)
-			return ret;
+			goto release_dma;
 		priv->baud_mux_clk = baud_mux_clk;
 		init_real_clk_rates(dev, priv);
 		clk_rate = priv->default_mux_rate;
@@ -1032,7 +1054,8 @@
 
 	if (clk_rate == 0) {
 		dev_err(dev, "clock-frequency or clk not defined\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_clk_disable;
 	}
 
 	dev_dbg(dev, "DMA is %senabled\n", priv->dma_enabled ? "" : "not ");
@@ -1075,14 +1098,18 @@
 		priv->rx_bufs = dma_alloc_coherent(dev,
 						   priv->rx_size,
 						   &priv->rx_addr, GFP_KERNEL);
-		if (!priv->rx_bufs)
+		if (!priv->rx_bufs) {
+			ret = -EINVAL;
 			goto err;
+		}
 		priv->tx_size = UART_XMIT_SIZE;
 		priv->tx_buf = dma_alloc_coherent(dev,
 						  priv->tx_size,
 						  &priv->tx_addr, GFP_KERNEL);
-		if (!priv->tx_buf)
+		if (!priv->tx_buf) {
+			ret = -EINVAL;
 			goto err;
+		}
 	}
 
 	ret = serial8250_register_8250_port(&up);
@@ -1096,6 +1123,7 @@
 	if (priv->dma_enabled) {
 		dma_irq = platform_get_irq_byname(pdev,  "dma");
 		if (dma_irq < 0) {
+			ret = dma_irq;
 			dev_err(dev, "no IRQ resource info\n");
 			goto err1;
 		}
@@ -1114,8 +1142,12 @@
 	serial8250_unregister_port(priv->line);
 err:
 	brcmuart_free_bufs(dev, priv);
-	brcmuart_arbitration(priv, 0);
-	return -ENODEV;
+err_clk_disable:
+	clk_disable_unprepare(baud_mux_clk);
+release_dma:
+	if (priv->dma_enabled)
+		brcmuart_arbitration(priv, 0);
+	return ret;
 }
 
 static int brcmuart_remove(struct platform_device *pdev)
@@ -1126,13 +1158,27 @@
 	hrtimer_cancel(&priv->hrt);
 	serial8250_unregister_port(priv->line);
 	brcmuart_free_bufs(&pdev->dev, priv);
-	brcmuart_arbitration(priv, 0);
+	clk_disable_unprepare(priv->baud_mux_clk);
+	if (priv->dma_enabled)
+		brcmuart_arbitration(priv, 0);
 	return 0;
 }
 
 static int __maybe_unused brcmuart_suspend(struct device *dev)
 {
 	struct brcmuart_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	struct uart_port *port = &up->port;
+	unsigned long flags;
+
+	/*
+	 * This will prevent resume from enabling RTS before the
+	 *  baud rate has been restored.
+	 */
+	spin_lock_irqsave(&port->lock, flags);
+	priv->saved_mctrl = port->mctrl;
+	port->mctrl &= ~TIOCM_RTS;
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	serial8250_suspend_port(priv->line);
 	clk_disable_unprepare(priv->baud_mux_clk);
@@ -1143,6 +1189,9 @@
 static int __maybe_unused brcmuart_resume(struct device *dev)
 {
 	struct brcmuart_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	struct uart_port *port = &up->port;
+	unsigned long flags;
 	int ret;
 
 	ret = clk_prepare_enable(priv->baud_mux_clk);
@@ -1165,6 +1214,15 @@
 		start_rx_dma(serial8250_get_port(priv->line));
 	}
 	serial8250_resume_port(priv->line);
+
+	if (priv->saved_mctrl & TIOCM_RTS) {
+		/* Restore RTS */
+		spin_lock_irqsave(&port->lock, flags);
+		port->mctrl |= TIOCM_RTS;
+		port->ops->set_mctrl(port, port->mctrl);
+		spin_unlock_irqrestore(&port->lock, flags);
+	}
+
 	return 0;
 }
 
@@ -1184,9 +1242,17 @@
 
 static int __init brcmuart_init(void)
 {
+	int ret;
+
 	brcmuart_debugfs_root = debugfs_create_dir(
 		brcmuart_platform_driver.driver.name, NULL);
-	return platform_driver_register(&brcmuart_platform_driver);
+	ret = platform_driver_register(&brcmuart_platform_driver);
+	if (ret) {
+		debugfs_remove_recursive(brcmuart_debugfs_root);
+		return ret;
+	}
+
+	return 0;
 }
 module_init(brcmuart_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_core.c
@@ -23,6 +23,7 @@
 #include <linux/sysrq.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/tty.h>
 #include <linux/ratelimit.h>
 #include <linux/tty_flip.h>
@@ -299,10 +300,9 @@
 		jiffies + uart_poll_timeout(&up->port) + HZ / 5);
 }
 
-static int univ8250_setup_irq(struct uart_8250_port *up)
+static void univ8250_setup_timer(struct uart_8250_port *up)
 {
 	struct uart_port *port = &up->port;
-	int retval = 0;
 
 	/*
 	 * The above check will only give an accurate result the first time
@@ -323,10 +323,16 @@
 	 */
 	if (!port->irq)
 		mod_timer(&up->timer, jiffies + uart_poll_timeout(port));
-	else
-		retval = serial_link_irq_chain(up);
+}
 
-	return retval;
+static int univ8250_setup_irq(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+
+	if (port->irq)
+		return serial_link_irq_chain(up);
+
+	return 0;
 }
 
 static void univ8250_release_irq(struct uart_8250_port *up)
@@ -382,6 +388,7 @@
 static const struct uart_8250_ops univ8250_driver_ops = {
 	.setup_irq	= univ8250_setup_irq,
 	.release_irq	= univ8250_release_irq,
+	.setup_timer	= univ8250_setup_timer,
 };
 
 static struct uart_8250_port serial8250_ports[UART_NR];
@@ -561,6 +568,9 @@
 
 		up->port.dev = dev;
 
+		if (uart_console_enabled(&up->port))
+			pm_runtime_get_sync(up->port.dev);
+
 		serial8250_apply_quirks(up);
 		uart_add_one_port(drv, &up->port);
 	}
@@ -1006,6 +1016,7 @@
 		uart->port.throttle	= up->port.throttle;
 		uart->port.unthrottle	= up->port.unthrottle;
 		uart->port.rs485_config	= up->port.rs485_config;
+		uart->port.rs485_supported = up->port.rs485_supported;
 		uart->port.rs485	= up->port.rs485;
 		uart->rs485_start_tx	= up->rs485_start_tx;
 		uart->rs485_stop_tx	= up->rs485_stop_tx;
@@ -1145,6 +1156,7 @@
 		uart->port.type = PORT_UNKNOWN;
 		uart->port.dev = &serial8250_isa_devs->dev;
 		uart->capabilities = 0;
+		serial8250_init_port(uart);
 		serial8250_apply_quirks(uart);
 		uart_add_one_port(&serial8250_reg, &uart->port);
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_dma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_dma.c
@@ -46,28 +46,57 @@
 	struct uart_8250_dma	*dma = p->dma;
 	struct tty_port		*tty_port = &p->port.state->port;
 	struct dma_tx_state	state;
+	enum dma_status		dma_status;
 	int			count;
 
-	dma->rx_running = 0;
-	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
+	/*
+	 * New DMA Rx can be started during the completion handler before it
+	 * could acquire port's lock and it might still be ongoing. Don't to
+	 * anything in such case.
+	 */
+	dma_status = dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
+	if (dma_status == DMA_IN_PROGRESS)
+		return;
 
 	count = dma->rx_size - state.residue;
 
 	tty_insert_flip_string(tty_port, dma->rx_buf, count);
 	p->port.icount.rx += count;
+	dma->rx_running = 0;
 
 	tty_flip_buffer_push(tty_port);
 }
 
+static void dma_rx_complete(void *param)
+{
+	struct uart_8250_port *p = param;
+	struct uart_8250_dma *dma = p->dma;
+	unsigned long flags;
+
+	spin_lock_irqsave(&p->port.lock, flags);
+	if (dma->rx_running)
+		__dma_rx_complete(p);
+	spin_unlock_irqrestore(&p->port.lock, flags);
+}
+
 int serial8250_tx_dma(struct uart_8250_port *p)
 {
 	struct uart_8250_dma		*dma = p->dma;
 	struct circ_buf			*xmit = &p->port.state->xmit;
 	struct dma_async_tx_descriptor	*desc;
+	struct uart_port		*up = &p->port;
 	int ret;
 
-	if (dma->tx_running)
+	if (dma->tx_running) {
+		if (up->x_char) {
+			dmaengine_pause(dma->txchan);
+			uart_xchar_out(up, UART_TX);
+			dmaengine_resume(dma->txchan);
+		}
 		return 0;
+	} else if (up->x_char) {
+		uart_xchar_out(up, UART_TX);
+	}
 
 	if (uart_tx_stopped(&p->port) || uart_circ_empty(xmit)) {
 		/* We have been called from __dma_tx_complete() */
@@ -77,6 +106,8 @@
 
 	dma->tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
 
+	serial8250_do_prepare_tx_dma(p);
+
 	desc = dmaengine_prep_slave_single(dma->txchan,
 					   dma->tx_addr + xmit->tail,
 					   dma->tx_size, DMA_MEM_TO_DEV,
@@ -106,6 +137,22 @@
 	return ret;
 }
 
+void serial8250_tx_dma_flush(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	if (!dma->tx_running)
+		return;
+
+	/*
+	 * kfifo_reset() has been called by the serial core, avoid
+	 * advancing and underflowing in __dma_tx_complete().
+	 */
+	dma->tx_size = 0;
+
+	dmaengine_terminate_async(dma->txchan);
+}
+
 int serial8250_rx_dma(struct uart_8250_port *p)
 {
 	struct uart_8250_dma		*dma = p->dma;
@@ -114,6 +161,8 @@
 	if (dma->rx_running)
 		return 0;
 
+	serial8250_do_prepare_rx_dma(p);
+
 	desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
 					   dma->rx_size, DMA_DEV_TO_MEM,
 					   DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
@@ -121,7 +170,7 @@
 		return -EBUSY;
 
 	dma->rx_running = 1;
-	desc->callback = __dma_rx_complete;
+	desc->callback = dma_rx_complete;
 	desc->callback_param = p;
 
 	dma->rx_cookie = dmaengine_submit(desc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_dw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_dw.c
@@ -124,12 +124,15 @@
 /* Returns once the transmitter is empty or we run out of retries */
 static void dw8250_tx_wait_empty(struct uart_port *p)
 {
+	struct uart_8250_port *up = up_to_u8250p(p);
 	unsigned int tries = 20000;
 	unsigned int delay_threshold = tries - 1000;
 	unsigned int lsr;
 
 	while (tries--) {
 		lsr = readb (p->membase + (UART_LSR << p->regshift));
+		up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+
 		if (lsr & UART_LSR_TEMT)
 			break;
 
@@ -726,7 +729,7 @@
 		.name		= "dw-apb-uart",
 		.pm		= &dw8250_pm_ops,
 		.of_match_table	= dw8250_of_match,
-		.acpi_match_table = ACPI_PTR(dw8250_acpi_match),
+		.acpi_match_table = dw8250_acpi_match,
 	},
 	.probe			= dw8250_probe,
 	.remove			= dw8250_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_dwlib.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_dwlib.c
@@ -80,7 +80,7 @@
 void dw8250_setup_port(struct uart_port *p)
 {
 	struct uart_8250_port *up = up_to_u8250p(p);
-	u32 reg;
+	u32 reg, old_dlf;
 
 	/*
 	 * If the Component Version Register returns zero, we know that
@@ -93,9 +93,11 @@
 	dev_dbg(p->dev, "Designware UART version %c.%c%c\n",
 		(reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
 
+	/* Preserve value written by firmware or bootloader  */
+	old_dlf = dw8250_readl_ext(p, DW_UART_DLF);
 	dw8250_writel_ext(p, DW_UART_DLF, ~0U);
 	reg = dw8250_readl_ext(p, DW_UART_DLF);
-	dw8250_writel_ext(p, DW_UART_DLF, 0);
+	dw8250_writel_ext(p, DW_UART_DLF, old_dlf);
 
 	if (reg) {
 		struct dw8250_port_data *d = p->private_data;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_early.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_early.c
@@ -199,6 +199,7 @@
 OF_EARLYCON_DECLARE(omap8250, "ti,omap2-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap3-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap4-uart", early_omap8250_setup);
+OF_EARLYCON_DECLARE(omap8250, "ti,am654-uart", early_omap8250_setup);
 
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_em.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_em.c
@@ -106,8 +106,8 @@
 	memset(&up, 0, sizeof(up));
 	up.port.mapbase = regs->start;
 	up.port.irq = irq;
-	up.port.type = PORT_UNKNOWN;
-	up.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT | UPF_IOREMAP;
+	up.port.type = PORT_16750;
+	up.port.flags = UPF_FIXED_PORT | UPF_IOREMAP | UPF_FIXED_TYPE;
 	up.port.dev = &pdev->dev;
 	up.port.private_data = priv;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_exar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_exar.c
@@ -40,8 +40,60 @@
 #define PCI_DEVICE_ID_COMMTECH_4224PCIE		0x0020
 #define PCI_DEVICE_ID_COMMTECH_4228PCIE		0x0021
 #define PCI_DEVICE_ID_COMMTECH_4222PCIE		0x0022
+
+#define PCI_VENDOR_ID_CONNECT_TECH				0x12c4
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_SP_OPTO        0x0340
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_SP_OPTO_A      0x0341
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_SP_OPTO_B      0x0342
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS           0x0350
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A         0x0351
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B         0x0352
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS           0x0353
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A        0x0354
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B        0x0355
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO      0x0360
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A    0x0361
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B    0x0362
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP             0x0370
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_232         0x0371
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485         0x0372
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP           0x0373
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP           0x0374
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP           0x0375
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_232_NS      0x0376
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT   0x0380
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT  0x0381
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO        0x0382
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO    0x0392
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP        0x03A0
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_232    0x03A1
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485    0x03A2
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_232_NS 0x03A3
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XEG001               0x0602
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XR35X_BASE           0x1000
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XR35X_2              0x1002
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XR35X_4              0x1004
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XR35X_8              0x1008
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XR35X_12             0x100C
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_PCIE_XR35X_16             0x1010
+#define PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG00X          0x110c
+#define PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG01X          0x110d
+#define PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_16                 0x1110
+
 #define PCI_DEVICE_ID_EXAR_XR17V4358		0x4358
 #define PCI_DEVICE_ID_EXAR_XR17V8358		0x8358
+#define PCI_DEVICE_ID_EXAR_XR17V252		0x0252
+#define PCI_DEVICE_ID_EXAR_XR17V254		0x0254
+#define PCI_DEVICE_ID_EXAR_XR17V258		0x0258
+
+#define PCI_SUBDEVICE_ID_USR_2980		0x0128
+#define PCI_SUBDEVICE_ID_USR_2981		0x0129
+
+#define PCI_DEVICE_ID_SEALEVEL_710xC		0x1001
+#define PCI_DEVICE_ID_SEALEVEL_720xC		0x1002
+#define PCI_DEVICE_ID_SEALEVEL_740xC		0x1004
+#define PCI_DEVICE_ID_SEALEVEL_780xC		0x1008
+#define PCI_DEVICE_ID_SEALEVEL_716xC		0x1010
 
 #define UART_EXAR_INT0		0x80
 #define UART_EXAR_8XMODE	0x88	/* 8X sampling rate select */
@@ -112,7 +164,9 @@
 struct exar8250;
 
 struct exar8250_platform {
-	int (*rs485_config)(struct uart_port *, struct serial_rs485 *);
+	int (*rs485_config)(struct uart_port *, struct ktermios *,
+			    struct serial_rs485 *);
+	const struct serial_rs485 *rs485_supported;
 	int (*register_gpio)(struct pci_dev *, struct uart_8250_port *);
 	void (*unregister_gpio)(struct uart_8250_port *);
 };
@@ -408,7 +462,7 @@
 	port->port.private_data = NULL;
 }
 
-static int generic_rs485_config(struct uart_port *port,
+static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
 				struct serial_rs485 *rs485)
 {
 	bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
@@ -431,13 +485,18 @@
 	return 0;
 }
 
+static const struct serial_rs485 generic_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
+};
+
 static const struct exar8250_platform exar8250_default_platform = {
 	.register_gpio = xr17v35x_register_gpio,
 	.unregister_gpio = xr17v35x_unregister_gpio,
 	.rs485_config = generic_rs485_config,
+	.rs485_supported = &generic_rs485_supported,
 };
 
-static int iot2040_rs485_config(struct uart_port *port,
+static int iot2040_rs485_config(struct uart_port *port, struct ktermios *termios,
 				struct serial_rs485 *rs485)
 {
 	bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
@@ -467,9 +526,14 @@
 	value |= mode;
 	writeb(value, p + UART_EXAR_MPIOLVL_7_0);
 
-	return generic_rs485_config(port, rs485);
+	return generic_rs485_config(port, termios, rs485);
 }
 
+static const struct serial_rs485 iot2040_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+		 SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
+};
+
 static const struct property_entry iot2040_gpio_properties[] = {
 	PROPERTY_ENTRY_U32("exar,first-pin", 10),
 	PROPERTY_ENTRY_U32("ngpios", 1),
@@ -498,6 +562,7 @@
 
 static const struct exar8250_platform iot2040_platform = {
 	.rs485_config = iot2040_rs485_config,
+	.rs485_supported = &iot2040_rs485_supported,
 	.register_gpio = iot2040_register_gpio,
 	.unregister_gpio = xr17v35x_unregister_gpio,
 };
@@ -540,6 +605,7 @@
 
 	port->port.uartclk = baud * 16;
 	port->port.rs485_config = platform->rs485_config;
+	port->port.rs485_supported = platform->rs485_supported;
 
 	/*
 	 * Setup the UART clock for the devices on expansion slot to
@@ -623,7 +689,14 @@
 
 	maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3);
 
-	nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
+	if (pcidev->vendor == PCI_VENDOR_ID_ACCESSIO)
+		nr_ports = BIT(((pcidev->device & 0x38) >> 3) - 1);
+	else if (board->num_ports)
+		nr_ports = board->num_ports;
+	else if (pcidev->vendor == PCI_VENDOR_ID_SEALEVEL)
+		nr_ports = pcidev->device & 0xff;
+	else
+		nr_ports = pcidev->device & 0x0f;
 
 	priv = devm_kzalloc(&pcidev->dev, struct_size(priv, line, nr_ports), GFP_KERNEL);
 	if (!priv)
@@ -685,6 +758,7 @@
 	for (i = 0; i < priv->nr; i++)
 		serial8250_unregister_port(priv->line[i]);
 
+	/* Ensure that every init quirk is properly torn down */
 	if (priv->board->exit)
 		priv->board->exit(pcidev);
 }
@@ -699,10 +773,6 @@
 		if (priv->line[i] >= 0)
 			serial8250_suspend_port(priv->line[i]);
 
-	/* Ensure that every init quirk is properly torn down */
-	if (priv->board->exit)
-		priv->board->exit(pcidev);
-
 	return 0;
 }
 
@@ -722,22 +792,6 @@
 
 static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
 
-static const struct exar8250_board acces_com_2x = {
-	.num_ports	= 2,
-	.setup		= pci_xr17c154_setup,
-};
-
-static const struct exar8250_board acces_com_4x = {
-	.num_ports	= 4,
-	.setup		= pci_xr17c154_setup,
-};
-
-static const struct exar8250_board acces_com_8x = {
-	.num_ports	= 8,
-	.setup		= pci_xr17c154_setup,
-};
-
-
 static const struct exar8250_board pbn_fastcom335_2 = {
 	.num_ports	= 2,
 	.setup		= pci_fastcom335_setup,
@@ -821,14 +875,23 @@
 		(kernel_ulong_t)&bd			\
 	}
 
+#define USR_DEVICE(devid, sdevid, bd) {			\
+	PCI_DEVICE_SUB(					\
+		PCI_VENDOR_ID_USR,			\
+		PCI_DEVICE_ID_EXAR_##devid,		\
+		PCI_VENDOR_ID_EXAR,			\
+		PCI_SUBDEVICE_ID_USR_##sdevid), 0, 0,	\
+		(kernel_ulong_t)&bd			\
+	}
+
 static const struct pci_device_id exar_pci_tbl[] = {
-	EXAR_DEVICE(ACCESSIO, COM_2S, acces_com_2x),
-	EXAR_DEVICE(ACCESSIO, COM_4S, acces_com_4x),
-	EXAR_DEVICE(ACCESSIO, COM_8S, acces_com_8x),
-	EXAR_DEVICE(ACCESSIO, COM232_8, acces_com_8x),
-	EXAR_DEVICE(ACCESSIO, COM_2SM, acces_com_2x),
-	EXAR_DEVICE(ACCESSIO, COM_4SM, acces_com_4x),
-	EXAR_DEVICE(ACCESSIO, COM_8SM, acces_com_8x),
+	EXAR_DEVICE(ACCESSIO, COM_2S, pbn_exar_XR17C15x),
+	EXAR_DEVICE(ACCESSIO, COM_4S, pbn_exar_XR17C15x),
+	EXAR_DEVICE(ACCESSIO, COM_8S, pbn_exar_XR17C15x),
+	EXAR_DEVICE(ACCESSIO, COM232_8, pbn_exar_XR17C15x),
+	EXAR_DEVICE(ACCESSIO, COM_2SM, pbn_exar_XR17C15x),
+	EXAR_DEVICE(ACCESSIO, COM_4SM, pbn_exar_XR17C15x),
+	EXAR_DEVICE(ACCESSIO, COM_8SM, pbn_exar_XR17C15x),
 
 	CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect),
 	CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect),
@@ -845,6 +908,10 @@
 
 	IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn),
 
+	/* USRobotics USR298x-OEM PCI Modems */
+	USR_DEVICE(XR17C152, 2980, pbn_exar_XR17C15x),
+	USR_DEVICE(XR17C152, 2981, pbn_exar_XR17C15x),
+
 	/* Exar Corp. XR17C15[248] Dual/Quad/Octal UART */
 	EXAR_DEVICE(EXAR, XR17C152, pbn_exar_XR17C15x),
 	EXAR_DEVICE(EXAR, XR17C154, pbn_exar_XR17C15x),
@@ -864,6 +931,12 @@
 	EXAR_DEVICE(COMMTECH, 4224PCI335, pbn_fastcom335_4),
 	EXAR_DEVICE(COMMTECH, 2324PCI335, pbn_fastcom335_4),
 	EXAR_DEVICE(COMMTECH, 2328PCI335, pbn_fastcom335_8),
+
+	EXAR_DEVICE(SEALEVEL, 710xC, pbn_exar_XR17V35x),
+	EXAR_DEVICE(SEALEVEL, 720xC, pbn_exar_XR17V35x),
+	EXAR_DEVICE(SEALEVEL, 740xC, pbn_exar_XR17V35x),
+	EXAR_DEVICE(SEALEVEL, 780xC, pbn_exar_XR17V35x),
+	EXAR_DEVICE(SEALEVEL, 716xC, pbn_exar_XR17V35x),
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, exar_pci_tbl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_fintek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_fintek.c
@@ -191,7 +191,7 @@
 	return -ENODEV;
 }
 
-static int fintek_8250_rs485_config(struct uart_port *port,
+static int fintek_8250_rs485_config(struct uart_port *port, struct ktermios *termios,
 			      struct serial_rs485 *rs485)
 {
 	uint8_t config = 0;
@@ -200,12 +200,12 @@
 	if (!pdata)
 		return -EINVAL;
 
-	/* Hardware do not support same RTS level on send and receive */
-	if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
-			!(rs485->flags & SER_RS485_RTS_AFTER_SEND))
-		return -EINVAL;
 
 	if (rs485->flags & SER_RS485_ENABLED) {
+		/* Hardware do not support same RTS level on send and receive */
+		if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+		    !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
+			return -EINVAL;
 		memset(rs485->padding, 0, sizeof(rs485->padding));
 		config |= RS485_URA;
 	} else {
@@ -290,25 +290,6 @@
 	}
 }
 
-static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
-			      struct fintek_8250 *pdata)
-{
-	sio_write_reg(pdata, LDN, pdata->index);
-
-	switch (pdata->pid) {
-	case CHIP_ID_F81966:
-	case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
-		sio_write_mask_reg(pdata, F81866_UART_CLK,
-			F81866_UART_CLK_MASK,
-			F81866_UART_CLK_14_769MHZ);
-
-		uart->port.uartclk = 921600 * 16;
-		break;
-	default: /* leave clock speed untouched */
-		break;
-	}
-}
-
 static void fintek_8250_set_termios(struct uart_port *port,
 				    struct ktermios *termios,
 				    struct ktermios *old)
@@ -430,7 +411,6 @@
 
 				fintek_8250_set_irq_mode(pdata, level_mode);
 				fintek_8250_set_max_fifo(pdata);
-				fintek_8250_goto_highspeed(uart, pdata);
 
 				fintek_8250_exit_key(addr[i]);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_fsl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_fsl.c
@@ -38,7 +38,7 @@
 
 	iir = port->serial_in(port, UART_IIR);
 	if (iir & UART_IIR_NO_INT) {
-		spin_unlock(&up->port.lock);
+		spin_unlock_irqrestore(&up->port.lock, flags);
 		return 0;
 	}
 
@@ -46,7 +46,7 @@
 	if (unlikely(up->lsr_saved_flags & UART_LSR_BI)) {
 		up->lsr_saved_flags &= ~UART_LSR_BI;
 		port->serial_in(port, UART_RX);
-		spin_unlock(&up->port.lock);
+		spin_unlock_irqrestore(&up->port.lock, flags);
 		return 1;
 	}
 
@@ -81,7 +81,7 @@
 	if ((lsr & UART_LSR_THRE) && (up->ier & UART_IER_THRI))
 		serial8250_tx_chars(up);
 
-	up->lsr_saved_flags = orig_lsr;
+	up->lsr_saved_flags |= orig_lsr & UART_LSR_BI;
 
 	uart_unlock_and_check_sysrq_irqrestore(&up->port, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_gsc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_gsc.c
@@ -26,7 +26,7 @@
 	unsigned long address;
 	int err;
 
-#ifdef CONFIG_64BIT
+#if defined(CONFIG_64BIT) && defined(CONFIG_IOSAPIC)
 	if (!dev->irq && (dev->id.sversion == 0xad))
 		dev->irq = iosapic_serial_irq(dev);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_lpc18xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_lpc18xx.c
@@ -32,7 +32,7 @@
 	int line;
 };
 
-static int lpc18xx_rs485_config(struct uart_port *port,
+static int lpc18xx_rs485_config(struct uart_port *port, struct ktermios *termios,
 				struct serial_rs485 *rs485)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_lpss.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_lpss.c
@@ -121,8 +121,7 @@
 {
 	struct dw_dma_slave *param = &lpss->dma_param;
 	struct pci_dev *pdev = to_pci_dev(port->dev);
-	unsigned int dma_devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0);
-	struct pci_dev *dma_dev = pci_get_slot(pdev->bus, dma_devfn);
+	struct pci_dev *dma_dev;
 
 	switch (pdev->device) {
 	case PCI_DEVICE_ID_INTEL_BYT_UART1:
@@ -141,6 +140,8 @@
 		return -EINVAL;
 	}
 
+	dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
+
 	param->dma_dev = &dma_dev->dev;
 	param->m_master = 0;
 	param->p_master = 1;
@@ -156,6 +157,14 @@
 	return 0;
 }
 
+static void byt_serial_exit(struct lpss8250 *lpss)
+{
+	struct dw_dma_slave *param = &lpss->dma_param;
+
+	/* Paired with pci_get_slot() in the byt_serial_setup() above */
+	put_device(param->dma_dev);
+}
+
 static int ehl_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 {
 	struct uart_8250_dma *dma = &lpss->data.dma;
@@ -168,9 +177,19 @@
 	 * matching with the registered General Purpose DMA controllers.
 	 */
 	up->dma = dma;
+
+	lpss->dma_maxburst = 16;
+
 	return 0;
 }
 
+static void ehl_serial_exit(struct lpss8250 *lpss)
+{
+	struct uart_8250_port *up = serial8250_get_port(lpss->data.line);
+
+	up->dma = NULL;
+}
+
 #ifdef CONFIG_SERIAL_8250_DMA
 static const struct dw_dma_platform_data qrk_serial_dma_pdata = {
 	.nr_channels = 2,
@@ -262,8 +281,13 @@
 	struct dw_dma_slave *rx_param, *tx_param;
 	struct device *dev = port->port.dev;
 
-	if (!lpss->dma_param.dma_dev)
+	if (!lpss->dma_param.dma_dev) {
+		dma = port->dma;
+		if (dma)
+			goto out_configuration_only;
+
 		return 0;
+	}
 
 	rx_param = devm_kzalloc(dev, sizeof(*rx_param), GFP_KERNEL);
 	if (!rx_param)
@@ -274,16 +298,18 @@
 		return -ENOMEM;
 
 	*rx_param = lpss->dma_param;
-	dma->rxconf.src_maxburst = lpss->dma_maxburst;
-
 	*tx_param = lpss->dma_param;
-	dma->txconf.dst_maxburst = lpss->dma_maxburst;
 
 	dma->fn = lpss8250_dma_filter;
 	dma->rx_param = rx_param;
 	dma->tx_param = tx_param;
 
 	port->dma = dma;
+
+out_configuration_only:
+	dma->rxconf.src_maxburst = lpss->dma_maxburst;
+	dma->txconf.dst_maxburst = lpss->dma_maxburst;
+
 	return 0;
 }
 
@@ -345,8 +371,7 @@
 	return 0;
 
 err_exit:
-	if (lpss->board->exit)
-		lpss->board->exit(lpss);
+	lpss->board->exit(lpss);
 	pci_free_irq_vectors(pdev);
 	return ret;
 }
@@ -357,8 +382,7 @@
 
 	serial8250_unregister_port(lpss->data.line);
 
-	if (lpss->board->exit)
-		lpss->board->exit(lpss);
+	lpss->board->exit(lpss);
 	pci_free_irq_vectors(pdev);
 }
 
@@ -366,12 +390,14 @@
 	.freq = 100000000,
 	.base_baud = 2764800,
 	.setup = byt_serial_setup,
+	.exit = byt_serial_exit,
 };
 
 static const struct lpss8250_board ehl_board = {
 	.freq = 200000000,
 	.base_baud = 12500000,
 	.setup = ehl_serial_setup,
+	.exit = ehl_serial_exit,
 };
 
 static const struct lpss8250_board qrk_board = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_mid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_mid.c
@@ -73,6 +73,11 @@
 	return 0;
 }
 
+static void pnw_exit(struct mid8250 *mid)
+{
+	pci_dev_put(mid->dma_dev);
+}
+
 static int tng_handle_irq(struct uart_port *p)
 {
 	struct mid8250 *mid = p->private_data;
@@ -124,6 +129,11 @@
 	return 0;
 }
 
+static void tng_exit(struct mid8250 *mid)
+{
+	pci_dev_put(mid->dma_dev);
+}
+
 static int dnv_handle_irq(struct uart_port *p)
 {
 	struct mid8250 *mid = p->private_data;
@@ -330,9 +340,9 @@
 
 	pci_set_drvdata(pdev, mid);
 	return 0;
+
 err:
-	if (mid->board->exit)
-		mid->board->exit(mid);
+	mid->board->exit(mid);
 	return ret;
 }
 
@@ -342,8 +352,7 @@
 
 	serial8250_unregister_port(mid->line);
 
-	if (mid->board->exit)
-		mid->board->exit(mid);
+	mid->board->exit(mid);
 }
 
 static const struct mid8250_board pnw_board = {
@@ -351,6 +360,7 @@
 	.freq = 50000000,
 	.base_baud = 115200,
 	.setup = pnw_setup,
+	.exit = pnw_exit,
 };
 
 static const struct mid8250_board tng_board = {
@@ -358,6 +368,7 @@
 	.freq = 38400000,
 	.base_baud = 1843200,
 	.setup = tng_setup,
+	.exit = tng_exit,
 };
 
 static const struct mid8250_board dnv_board = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_mtk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_mtk.c
@@ -37,6 +37,7 @@
 #define MTK_UART_IER_RTSI	0x40	/* Enable RTS Modem status interrupt */
 #define MTK_UART_IER_CTSI	0x80	/* Enable CTS Modem status interrupt */
 
+#define MTK_UART_EFR		38	/* I/O: Extended Features Register */
 #define MTK_UART_EFR_EN		0x10	/* Enable enhancement feature */
 #define MTK_UART_EFR_RTS	0x40	/* Enable hardware rx flow control */
 #define MTK_UART_EFR_CTS	0x80	/* Enable hardware tx flow control */
@@ -53,6 +54,9 @@
 #define MTK_UART_TX_TRIGGER	1
 #define MTK_UART_RX_TRIGGER	MTK_UART_RX_SIZE
 
+#define MTK_UART_XON1		40	/* I/O: Xon character 1 */
+#define MTK_UART_XOFF1		42	/* I/O: Xoff character 1 */
+
 #ifdef CONFIG_SERIAL_8250_DMA
 enum dma_rx_status {
 	DMA_RX_START = 0,
@@ -169,7 +173,7 @@
 		   MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_out(up, UART_EFR, UART_EFR_ECB);
+	serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
 	serial_out(up, UART_LCR, lcr);
 
 	if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0)
@@ -232,7 +236,7 @@
 	int lcr = serial_in(up, UART_LCR);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_out(up, UART_EFR, UART_EFR_ECB);
+	serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
 	serial_out(up, UART_LCR, lcr);
 	lcr = serial_in(up, UART_LCR);
 
@@ -241,7 +245,7 @@
 		serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
 		serial_out(up, MTK_UART_ESCAPE_EN, 0x00);
 		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-		serial_out(up, UART_EFR, serial_in(up, UART_EFR) &
+		serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) &
 			(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)));
 		serial_out(up, UART_LCR, lcr);
 		mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI |
@@ -255,8 +259,8 @@
 		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 		/*enable hw flow control*/
-		serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC |
-			(serial_in(up, UART_EFR) &
+		serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC |
+			(serial_in(up, MTK_UART_EFR) &
 			(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
 
 		serial_out(up, UART_LCR, lcr);
@@ -270,12 +274,12 @@
 		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 
 		/*enable sw flow control */
-		serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
-			(serial_in(up, UART_EFR) &
+		serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
+			(serial_in(up, MTK_UART_EFR) &
 			(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
 
-		serial_out(up, UART_XON1, START_CHAR(port->state->port.tty));
-		serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty));
+		serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty));
+		serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty));
 		serial_out(up, UART_LCR, lcr);
 		mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI);
 		mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_of.c
@@ -83,8 +83,17 @@
 		port->mapsize = resource_size(&resource);
 
 		/* Check for shifted address mapping */
-		if (of_property_read_u32(np, "reg-offset", &prop) == 0)
+		if (of_property_read_u32(np, "reg-offset", &prop) == 0) {
+			if (prop >= port->mapsize) {
+				dev_warn(&ofdev->dev, "reg-offset %u exceeds region size %pa\n",
+					 prop, &port->mapsize);
+				ret = -EINVAL;
+				goto err_unprepare;
+			}
+
 			port->mapbase += prop;
+			port->mapsize -= prop;
+		}
 
 		port->iotype = UPIO_MEM;
 		if (of_property_read_u32(np, "reg-io-width", &prop) == 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_omap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_omap.c
@@ -32,6 +32,7 @@
 #include "8250.h"
 
 #define DEFAULT_CLK_SPEED	48000000
+#define OMAP_UART_REGSHIFT	2
 
 #define UART_ERRATA_i202_MDR1_ACCESS	(1 << 0)
 #define OMAP_UART_WER_HAS_TX_WAKEUP	(1 << 1)
@@ -109,6 +110,7 @@
 #define UART_OMAP_RX_LVL		0x19
 
 struct omap8250_priv {
+	void __iomem *membase;
 	int line;
 	u8 habit;
 	u8 mdr1;
@@ -152,12 +154,20 @@
 static inline void omap_8250_rx_dma_flush(struct uart_8250_port *p) { }
 #endif
 
-static u32 uart_read(struct uart_8250_port *up, u32 reg)
+static u32 uart_read(struct omap8250_priv *priv, u32 reg)
 {
-	return readl(up->port.membase + (reg << up->port.regshift));
+	return readl(priv->membase + (reg << OMAP_UART_REGSHIFT));
 }
 
-static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
+/* Timeout low and High */
+#define UART_OMAP_TO_L                 0x26
+#define UART_OMAP_TO_H                 0x27
+
+/*
+ * Called on runtime PM resume path from omap8250_restore_regs(), and
+ * omap8250_set_mctrl().
+ */
+static void __omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 	struct omap8250_priv *priv = up->port.private_data;
@@ -181,6 +191,20 @@
 	}
 }
 
+static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	int err;
+
+	err = pm_runtime_resume_and_get(port->dev);
+	if (err)
+		return;
+
+	__omap8250_set_mctrl(port, mctrl);
+
+	pm_runtime_mark_last_busy(port->dev);
+	pm_runtime_put_autosuspend(port->dev);
+}
+
 /*
  * Work Around for Errata i202 (2430, 3430, 3630, 4430 and 4460)
  * The access to uart register after MDR1 Access
@@ -193,27 +217,10 @@
 static void omap_8250_mdr1_errataset(struct uart_8250_port *up,
 				     struct omap8250_priv *priv)
 {
-	u8 timeout = 255;
-
 	serial_out(up, UART_OMAP_MDR1, priv->mdr1);
 	udelay(2);
 	serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_XMIT |
 			UART_FCR_CLEAR_RCVR);
-	/*
-	 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
-	 * TX_FIFO_E bit is 1.
-	 */
-	while (UART_LSR_THRE != (serial_in(up, UART_LSR) &
-				(UART_LSR_THRE | UART_LSR_DR))) {
-		timeout--;
-		if (!timeout) {
-			/* Should *never* happen. we warn and carry on */
-			dev_crit(up->port.dev, "Errata i202: timedout %x\n",
-				 serial_in(up, UART_LSR));
-			break;
-		}
-		udelay(1);
-	}
 }
 
 static void omap_8250_get_divisor(struct uart_port *port, unsigned int baud,
@@ -292,6 +299,7 @@
 {
 	struct omap8250_priv *priv = up->port.private_data;
 	struct uart_8250_dma	*dma = up->dma;
+	u8 mcr = serial8250_in_MCR(up);
 
 	if (dma && dma->tx_running) {
 		/*
@@ -308,7 +316,7 @@
 	serial_out(up, UART_EFR, UART_EFR_ECB);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial8250_out_MCR(up, UART_MCR_TCRTLR);
+	serial8250_out_MCR(up, mcr | UART_MCR_TCRTLR);
 	serial_out(up, UART_FCR, up->fcr);
 
 	omap8250_update_scr(up, priv);
@@ -324,7 +332,8 @@
 	serial_out(up, UART_LCR, 0);
 
 	/* drop TCR + TLR access, we setup XON/XOFF later */
-	serial8250_out_MCR(up, up->mcr);
+	serial8250_out_MCR(up, mcr);
+
 	serial_out(up, UART_IER, up->ier);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
@@ -341,7 +350,10 @@
 
 	omap8250_update_mdr1(up, priv);
 
-	up->port.ops->set_mctrl(&up->port, up->port.mctrl);
+	__omap8250_set_mctrl(&up->port, up->port.mctrl);
+
+	if (up->port.rs485.flags & SER_RS485_ENABLED)
+		serial8250_em485_stop_tx(up);
 }
 
 /*
@@ -546,7 +558,7 @@
 	u32 mvr, scheme;
 	u16 revision, major, minor;
 
-	mvr = uart_read(up, UART_OMAP_MVER);
+	mvr = uart_read(priv, UART_OMAP_MVER);
 
 	/* Check revision register scheme */
 	scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
@@ -634,19 +646,33 @@
 
 	/*
 	 * On K3 SoCs, it is observed that RX TIMEOUT is signalled after
-	 * FIFO has been drained, in which case a dummy read of RX FIFO
-	 * is required to clear RX TIMEOUT condition.
+	 * FIFO has been drained or erroneously.
+	 * So apply solution of Errata i2310 as mentioned in
+	 * https://www.ti.com/lit/pdf/sprz536
 	 */
 	if (priv->habit & UART_RX_TIMEOUT_QUIRK &&
 	    (iir & UART_IIR_RX_TIMEOUT) == UART_IIR_RX_TIMEOUT &&
 	    serial_port_in(port, UART_OMAP_RX_LVL) == 0) {
-		serial_port_in(port, UART_RX);
+		unsigned char efr2, timeout_h, timeout_l;
+
+		efr2 = serial_in(up, UART_OMAP_EFR2);
+		timeout_h = serial_in(up, UART_OMAP_TO_H);
+		timeout_l = serial_in(up, UART_OMAP_TO_L);
+		serial_out(up, UART_OMAP_TO_H, 0xFF);
+		serial_out(up, UART_OMAP_TO_L, 0xFF);
+		serial_out(up, UART_OMAP_EFR2, UART_OMAP_EFR2_TIMEOUT_BEHAVE);
+		serial_in(up, UART_IIR);
+		serial_out(up, UART_OMAP_EFR2, efr2);
+		serial_out(up, UART_OMAP_TO_H, timeout_h);
+		serial_out(up, UART_OMAP_TO_L, timeout_l);
 	}
 
 	/* Stop processing interrupts on input overrun */
 	if ((lsr & UART_LSR_OE) && up->overrun_backoff_time_ms > 0) {
 		unsigned long delay;
 
+		/* Synchronize UART_IER access against the console. */
+		spin_lock(&port->lock);
 		up->ier = port->serial_in(port, UART_IER);
 		if (up->ier & (UART_IER_RLSI | UART_IER_RDI)) {
 			port->ops->stop_rx(port);
@@ -656,6 +682,7 @@
 			 */
 			cancel_delayed_work(&up->overrun_backoff);
 		}
+		spin_unlock(&port->lock);
 
 		delay = msecs_to_jiffies(up->overrun_backoff_time_ms);
 		schedule_delayed_work(&up->overrun_backoff, delay);
@@ -680,7 +707,6 @@
 
 	pm_runtime_get_sync(port->dev);
 
-	up->mcr = 0;
 	serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
 
 	serial_out(up, UART_LCR, UART_LCR_WLEN8);
@@ -737,12 +763,12 @@
 	struct uart_8250_port *up = up_to_u8250p(port);
 	struct omap8250_priv *priv = port->private_data;
 
+	pm_runtime_get_sync(port->dev);
+
 	flush_work(&priv->qos_work);
 	if (up->dma)
 		omap_8250_rx_dma_flush(up);
 
-	pm_runtime_get_sync(port->dev);
-
 	serial_out(up, UART_OMAP_WER, 0);
 	if (priv->habit & UART_HAS_EFR2)
 		serial_out(up, UART_OMAP_EFR2, 0x0);
@@ -829,7 +855,7 @@
 	if (priv->habit & UART_HAS_RHR_IT_DIS) {
 		reg = serial_in(p, UART_OMAP_IER2);
 		reg &= ~UART_OMAP_IER2_RHR_IT_DIS;
-		serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS);
+		serial_out(p, UART_OMAP_IER2, reg);
 	}
 
 	dmaengine_tx_status(rxchan, cookie, &state);
@@ -971,7 +997,7 @@
 	if (priv->habit & UART_HAS_RHR_IT_DIS) {
 		reg = serial_in(p, UART_OMAP_IER2);
 		reg |= UART_OMAP_IER2_RHR_IT_DIS;
-		serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS);
+		serial_out(p, UART_OMAP_IER2, reg);
 	}
 
 	dma_async_issue_pending(dma->rxchan);
@@ -1193,10 +1219,12 @@
 
 	status = serial_port_in(port, UART_LSR);
 
-	if (priv->habit & UART_HAS_EFR2)
-		am654_8250_handle_rx_dma(up, iir, status);
-	else
-		status = omap_8250_handle_rx_dma(up, iir, status);
+	if ((iir & 0x3f) != UART_IIR_THRI) {
+		if (priv->habit & UART_HAS_EFR2)
+			am654_8250_handle_rx_dma(up, iir, status);
+		else
+			status = omap_8250_handle_rx_dma(up, iir, status);
+	}
 
 	serial8250_modem_status(up);
 	if (status & UART_LSR_THRE && up->dma->tx_err) {
@@ -1328,7 +1356,7 @@
 		UPF_HARD_FLOW;
 	up.port.private_data = priv;
 
-	up.port.regshift = 2;
+	up.port.regshift = OMAP_UART_REGSHIFT;
 	up.port.fifosize = 64;
 	up.tx_loadsz = 64;
 	up.capabilities = UART_CAP_FIFO;
@@ -1389,6 +1417,8 @@
 			 DEFAULT_CLK_SPEED);
 	}
 
+	priv->membase = membase;
+	priv->line = -ENODEV;
 	priv->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
 	priv->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
 	cpu_latency_qos_add_request(&priv->pm_qos_request, priv->latency);
@@ -1396,6 +1426,8 @@
 
 	spin_lock_init(&priv->rx_dma_lock);
 
+	platform_set_drvdata(pdev, priv);
+
 	device_init_wakeup(&pdev->dev, true);
 	pm_runtime_enable(&pdev->dev);
 	pm_runtime_use_autosuspend(&pdev->dev);
@@ -1457,25 +1489,33 @@
 		goto err;
 	}
 	priv->line = ret;
-	platform_set_drvdata(pdev, priv);
 	pm_runtime_mark_last_busy(&pdev->dev);
 	pm_runtime_put_autosuspend(&pdev->dev);
 	return 0;
 err:
 	pm_runtime_dont_use_autosuspend(&pdev->dev);
 	pm_runtime_put_sync(&pdev->dev);
+	flush_work(&priv->qos_work);
 	pm_runtime_disable(&pdev->dev);
+	cpu_latency_qos_remove_request(&priv->pm_qos_request);
 	return ret;
 }
 
 static int omap8250_remove(struct platform_device *pdev)
 {
 	struct omap8250_priv *priv = platform_get_drvdata(pdev);
+	int err;
 
+	err = pm_runtime_resume_and_get(&pdev->dev);
+	if (err)
+		dev_err(&pdev->dev, "Failed to resume hardware\n");
+
+	serial8250_unregister_port(priv->line);
+	priv->line = -ENODEV;
 	pm_runtime_dont_use_autosuspend(&pdev->dev);
 	pm_runtime_put_sync(&pdev->dev);
+	flush_work(&priv->qos_work);
 	pm_runtime_disable(&pdev->dev);
-	serial8250_unregister_port(priv->line);
 	cpu_latency_qos_remove_request(&priv->pm_qos_request);
 	device_init_wakeup(&pdev->dev, false);
 	return 0;
@@ -1505,25 +1545,40 @@
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
 	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	int err = 0;
 
 	serial8250_suspend_port(priv->line);
 
-	pm_runtime_get_sync(dev);
+	err = pm_runtime_resume_and_get(dev);
+	if (err)
+		return err;
 	if (!device_may_wakeup(dev))
 		priv->wer = 0;
 	serial_out(up, UART_OMAP_WER, priv->wer);
-	pm_runtime_mark_last_busy(dev);
-	pm_runtime_put_autosuspend(dev);
-
+	if (uart_console(&up->port) && console_suspend_enabled)
+		err = pm_runtime_force_suspend(dev);
 	flush_work(&priv->qos_work);
-	return 0;
+
+	return err;
 }
 
 static int omap8250_resume(struct device *dev)
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	int err;
+
+	if (uart_console(&up->port) && console_suspend_enabled) {
+		err = pm_runtime_force_resume(dev);
+		if (err)
+			return err;
+	}
 
 	serial8250_resume_port(priv->line);
+	/* Paired with pm_runtime_resume_and_get() in omap8250_suspend() */
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+
 	return 0;
 }
 #else
@@ -1547,11 +1602,15 @@
 	return 0;
 }
 
+static void uart_write(struct omap8250_priv *priv, u32 reg, u32 val)
+{
+	writel(val, priv->membase + (reg << OMAP_UART_REGSHIFT));
+}
+
 /* TODO: in future, this should happen via API in drivers/reset/ */
 static int omap8250_soft_reset(struct device *dev)
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
-	struct uart_8250_port *up = serial8250_get_port(priv->line);
 	int timeout = 100;
 	int sysc;
 	int syss;
@@ -1565,20 +1624,20 @@
 	 * needing omap8250_soft_reset() quirk. Do it in two writes as
 	 * recommended in the comment for omap8250_update_scr().
 	 */
-	serial_out(up, UART_OMAP_SCR, OMAP_UART_SCR_DMAMODE_1);
-	serial_out(up, UART_OMAP_SCR,
+	uart_write(priv, UART_OMAP_SCR, OMAP_UART_SCR_DMAMODE_1);
+	uart_write(priv, UART_OMAP_SCR,
 		   OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL);
 
-	sysc = serial_in(up, UART_OMAP_SYSC);
+	sysc = uart_read(priv, UART_OMAP_SYSC);
 
 	/* softreset the UART */
 	sysc |= OMAP_UART_SYSC_SOFTRESET;
-	serial_out(up, UART_OMAP_SYSC, sysc);
+	uart_write(priv, UART_OMAP_SYSC, sysc);
 
 	/* By experiments, 1us enough for reset complete on AM335x */
 	do {
 		udelay(1);
-		syss = serial_in(up, UART_OMAP_SYSS);
+		syss = uart_read(priv, UART_OMAP_SYSS);
 	} while (--timeout && !(syss & OMAP_UART_SYSS_RESETDONE));
 
 	if (!timeout) {
@@ -1592,23 +1651,10 @@
 static int omap8250_runtime_suspend(struct device *dev)
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
-	struct uart_8250_port *up;
+	struct uart_8250_port *up = NULL;
 
-	/* In case runtime-pm tries this before we are setup */
-	if (!priv)
-		return 0;
-
-	up = serial8250_get_port(priv->line);
-	/*
-	 * When using 'no_console_suspend', the console UART must not be
-	 * suspended. Since driver suspend is managed by runtime suspend,
-	 * preventing runtime suspend (by returning error) will keep device
-	 * active during suspend.
-	 */
-	if (priv->is_suspending && !console_suspend_enabled) {
-		if (uart_console(&up->port))
-			return -EBUSY;
-	}
+	if (priv->line >= 0)
+		up = serial8250_get_port(priv->line);
 
 	if (priv->habit & UART_ERRATA_CLOCK_DISABLE) {
 		int ret;
@@ -1617,13 +1663,15 @@
 		if (ret)
 			return ret;
 
-		/* Restore to UART mode after reset (for wakeup) */
-		omap8250_update_mdr1(up, priv);
-		/* Restore wakeup enable register */
-		serial_out(up, UART_OMAP_WER, priv->wer);
+		if (up) {
+			/* Restore to UART mode after reset (for wakeup) */
+			omap8250_update_mdr1(up, priv);
+			/* Restore wakeup enable register */
+			serial_out(up, UART_OMAP_WER, priv->wer);
+		}
 	}
 
-	if (up->dma && up->dma->rxchan)
+	if (up && up->dma && up->dma->rxchan)
 		omap_8250_rx_dma_flush(up);
 
 	priv->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
@@ -1635,18 +1683,15 @@
 static int omap8250_runtime_resume(struct device *dev)
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
-	struct uart_8250_port *up;
-
-	/* In case runtime-pm tries this before we are setup */
-	if (!priv)
-		return 0;
+	struct uart_8250_port *up = NULL;
 
-	up = serial8250_get_port(priv->line);
+	if (priv->line >= 0)
+		up = serial8250_get_port(priv->line);
 
-	if (omap8250_lost_context(up))
+	if (up && omap8250_lost_context(up))
 		omap8250_restore_regs(up);
 
-	if (up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2))
+	if (up && up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2))
 		omap_8250_rx_dma(up);
 
 	priv->latency = priv->calc_latency;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_pci.c
@@ -11,6 +11,7 @@
 #include <linux/pci.h>
 #include <linux/string.h>
 #include <linux/kernel.h>
+#include <linux/math.h>
 #include <linux/slab.h>
 #include <linux/delay.h>
 #include <linux/tty.h>
@@ -65,6 +66,8 @@
 			 0xA000, 0x1000) },
 	{ PCI_DEVICE_SUB(PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9922,
 			 0xA000, 0x1000) },
+	{ PCI_DEVICE_SUB(PCI_VENDOR_ID_ASIX, PCI_DEVICE_ID_ASIX_AX99100,
+			 0xA000, 0x1000) },
 	{ PCI_DEVICE_SUB(PCI_VENDOR_ID_HP_3PAR, PCI_DEVICE_ID_HPE_PCI_SERIAL,
 			 PCI_ANY_ID, PCI_ANY_ID) },
 	{ }
@@ -75,13 +78,12 @@
 
 static void moan_device(const char *str, struct pci_dev *dev)
 {
-	dev_err(&dev->dev,
-	       "%s: %s\n"
+	pci_err(dev, "%s\n"
 	       "Please send the output of lspci -vv, this\n"
 	       "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n"
 	       "manufacturer and name of serial board or\n"
 	       "modem board to <linux-serial@vger.kernel.org>.\n",
-	       pci_name(dev), str, dev->vendor, dev->device,
+	       str, dev->vendor, dev->device,
 	       dev->subsystem_vendor, dev->subsystem_device);
 }
 
@@ -238,7 +240,7 @@
 	/* is firmware started? */
 	pci_read_config_dword(dev, 0x44, &oldval);
 	if (oldval == 0x00001000L) { /* RESET value */
-		dev_dbg(&dev->dev, "Local i960 firmware missing\n");
+		pci_dbg(dev, "Local i960 firmware missing\n");
 		return -ENODEV;
 	}
 	return 0;
@@ -588,9 +590,8 @@
 	 * (0,2,3,5,6: serial only -- 7,8,9: serial + parallel)
 	 */
 	if ((dev->subsystem_device & 0x00f0) >= 0x70) {
-		dev_info(&dev->dev,
-			"ignoring Timedia subdevice %04x for parport_serial\n",
-			dev->subsystem_device);
+		pci_info(dev, "ignoring Timedia subdevice %04x for parport_serial\n",
+			 dev->subsystem_device);
 		return -ENODEV;
 	}
 
@@ -827,8 +828,7 @@
 		if (sub_serports > 0)
 			return sub_serports;
 
-		dev_err(&dev->dev,
-			"NetMos/Mostech serial driver ignoring port on ambiguous config.\n");
+		pci_err(dev, "NetMos/Mostech serial driver ignoring port on ambiguous config.\n");
 		return 0;
 	}
 
@@ -897,18 +897,16 @@
 /* enable IO_Space bit */
 #define ITE_887x_POSIO_ENABLE		(1 << 31)
 
+/* inta_addr are the configuration addresses of the ITE */
+static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0, 0x200, 0x280 };
 static int pci_ite887x_init(struct pci_dev *dev)
 {
-	/* inta_addr are the configuration addresses of the ITE */
-	static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0,
-							0x200, 0x280, 0 };
 	int ret, i, type;
 	struct resource *iobase = NULL;
 	u32 miscr, uartbar, ioport;
 
 	/* search for the base-ioport */
-	i = 0;
-	while (inta_addr[i] && iobase == NULL) {
+	for (i = 0; i < ARRAY_SIZE(inta_addr); i++) {
 		iobase = request_region(inta_addr[i], ITE_887x_IOSIZE,
 								"ite887x");
 		if (iobase != NULL) {
@@ -925,13 +923,11 @@
 				break;
 			}
 			release_region(iobase->start, ITE_887x_IOSIZE);
-			iobase = NULL;
 		}
-		i++;
 	}
 
-	if (!inta_addr[i]) {
-		dev_err(&dev->dev, "ite887x: could not find iobase\n");
+	if (i == ARRAY_SIZE(inta_addr)) {
+		pci_err(dev, "could not find iobase\n");
 		return -ENODEV;
 	}
 
@@ -1001,43 +997,29 @@
 }
 
 /*
- * EndRun Technologies.
- * Determine the number of ports available on the device.
+ * Oxford Semiconductor Inc.
+ * Check if an OxSemi device is part of the Tornado range of devices.
  */
 #define PCI_VENDOR_ID_ENDRUN			0x7401
 #define PCI_DEVICE_ID_ENDRUN_1588	0xe100
 
-static int pci_endrun_init(struct pci_dev *dev)
+static bool pci_oxsemi_tornado_p(struct pci_dev *dev)
 {
-	u8 __iomem *p;
-	unsigned long deviceID;
-	unsigned int  number_uarts = 0;
+	/* OxSemi Tornado devices are all 0xCxxx */
+	if (dev->vendor == PCI_VENDOR_ID_OXSEMI &&
+	    (dev->device & 0xf000) != 0xc000)
+		return false;
 
-	/* EndRun device is all 0xexxx */
+	/* EndRun devices are all 0xExxx */
 	if (dev->vendor == PCI_VENDOR_ID_ENDRUN &&
-		(dev->device & 0xf000) != 0xe000)
-		return 0;
+	    (dev->device & 0xf000) != 0xe000)
+		return false;
 
-	p = pci_iomap(dev, 0, 5);
-	if (p == NULL)
-		return -ENOMEM;
-
-	deviceID = ioread32(p);
-	/* EndRun device */
-	if (deviceID == 0x07000200) {
-		number_uarts = ioread8(p + 4);
-		dev_dbg(&dev->dev,
-			"%d ports detected on EndRun PCI Express device\n",
-			number_uarts);
-	}
-	pci_iounmap(dev, p);
-	return number_uarts;
+	return true;
 }
 
 /*
- * Oxford Semiconductor Inc.
- * Check that device is part of the Tornado range of devices, then determine
- * the number of ports available on the device.
+ * Determine the number of ports available on a Tornado device.
  */
 static int pci_oxsemi_tornado_init(struct pci_dev *dev)
 {
@@ -1045,9 +1027,7 @@
 	unsigned long deviceID;
 	unsigned int  number_uarts = 0;
 
-	/* OxSemi Tornado devices are all 0xCxxx */
-	if (dev->vendor == PCI_VENDOR_ID_OXSEMI &&
-	    (dev->device & 0xF000) != 0xC000)
+	if (!pci_oxsemi_tornado_p(dev))
 		return 0;
 
 	p = pci_iomap(dev, 0, 5);
@@ -1058,20 +1038,220 @@
 	/* Tornado device */
 	if (deviceID == 0x07000200) {
 		number_uarts = ioread8(p + 4);
-		dev_dbg(&dev->dev,
-			"%d ports detected on Oxford PCI Express device\n",
-			number_uarts);
+		pci_dbg(dev, "%d ports detected on %s PCI Express device\n",
+			number_uarts,
+			dev->vendor == PCI_VENDOR_ID_ENDRUN ?
+			"EndRun" : "Oxford");
 	}
 	pci_iounmap(dev, p);
 	return number_uarts;
 }
 
-static int pci_asix_setup(struct serial_private *priv,
-		  const struct pciserial_board *board,
-		  struct uart_8250_port *port, int idx)
+/* Tornado-specific constants for the TCR and CPR registers; see below.  */
+#define OXSEMI_TORNADO_TCR_MASK	0xf
+#define OXSEMI_TORNADO_CPR_MASK	0x1ff
+#define OXSEMI_TORNADO_CPR_MIN	0x008
+#define OXSEMI_TORNADO_CPR_DEF	0x10f
+
+/*
+ * Determine the oversampling rate, the clock prescaler, and the clock
+ * divisor for the requested baud rate.  The clock rate is 62.5 MHz,
+ * which is four times the baud base, and the prescaler increments in
+ * steps of 1/8.  Therefore to make calculations on integers we need
+ * to use a scaled clock rate, which is the baud base multiplied by 32
+ * (or our assumed UART clock rate multiplied by 2).
+ *
+ * The allowed oversampling rates are from 4 up to 16 inclusive (values
+ * from 0 to 3 inclusive map to 16).  Likewise the clock prescaler allows
+ * values between 1.000 and 63.875 inclusive (operation for values from
+ * 0.000 to 0.875 has not been specified).  The clock divisor is the usual
+ * unsigned 16-bit integer.
+ *
+ * For the most accurate baud rate we use a table of predetermined
+ * oversampling rates and clock prescalers that records all possible
+ * products of the two parameters in the range from 4 up to 255 inclusive,
+ * and additionally 335 for the 1500000bps rate, with the prescaler scaled
+ * by 8.  The table is sorted by the decreasing value of the oversampling
+ * rate and ties are resolved by sorting by the decreasing value of the
+ * product.  This way preference is given to higher oversampling rates.
+ *
+ * We iterate over the table and choose the product of an oversampling
+ * rate and a clock prescaler that gives the lowest integer division
+ * result deviation, or if an exact integer divider is found we stop
+ * looking for it right away.  We do some fixup if the resulting clock
+ * divisor required would be out of its unsigned 16-bit integer range.
+ *
+ * Finally we abuse the supposed fractional part returned to encode the
+ * 4-bit value of the oversampling rate and the 9-bit value of the clock
+ * prescaler which will end up in the TCR and CPR/CPR2 registers.
+ */
+static unsigned int pci_oxsemi_tornado_get_divisor(struct uart_port *port,
+						   unsigned int baud,
+						   unsigned int *frac)
+{
+	static u8 p[][2] = {
+		{ 16, 14, }, { 16, 13, }, { 16, 12, }, { 16, 11, },
+		{ 16, 10, }, { 16,  9, }, { 16,  8, }, { 15, 17, },
+		{ 15, 16, }, { 15, 15, }, { 15, 14, }, { 15, 13, },
+		{ 15, 12, }, { 15, 11, }, { 15, 10, }, { 15,  9, },
+		{ 15,  8, }, { 14, 18, }, { 14, 17, }, { 14, 14, },
+		{ 14, 13, }, { 14, 12, }, { 14, 11, }, { 14, 10, },
+		{ 14,  9, }, { 14,  8, }, { 13, 19, }, { 13, 18, },
+		{ 13, 17, }, { 13, 13, }, { 13, 12, }, { 13, 11, },
+		{ 13, 10, }, { 13,  9, }, { 13,  8, }, { 12, 19, },
+		{ 12, 18, }, { 12, 17, }, { 12, 11, }, { 12,  9, },
+		{ 12,  8, }, { 11, 23, }, { 11, 22, }, { 11, 21, },
+		{ 11, 20, }, { 11, 19, }, { 11, 18, }, { 11, 17, },
+		{ 11, 11, }, { 11, 10, }, { 11,  9, }, { 11,  8, },
+		{ 10, 25, }, { 10, 23, }, { 10, 20, }, { 10, 19, },
+		{ 10, 17, }, { 10, 10, }, { 10,  9, }, { 10,  8, },
+		{  9, 27, }, {  9, 23, }, {  9, 21, }, {  9, 19, },
+		{  9, 18, }, {  9, 17, }, {  9,  9, }, {  9,  8, },
+		{  8, 31, }, {  8, 29, }, {  8, 23, }, {  8, 19, },
+		{  8, 17, }, {  8,  8, }, {  7, 35, }, {  7, 31, },
+		{  7, 29, }, {  7, 25, }, {  7, 23, }, {  7, 21, },
+		{  7, 19, }, {  7, 17, }, {  7, 15, }, {  7, 14, },
+		{  7, 13, }, {  7, 12, }, {  7, 11, }, {  7, 10, },
+		{  7,  9, }, {  7,  8, }, {  6, 41, }, {  6, 37, },
+		{  6, 31, }, {  6, 29, }, {  6, 23, }, {  6, 19, },
+		{  6, 17, }, {  6, 13, }, {  6, 11, }, {  6, 10, },
+		{  6,  9, }, {  6,  8, }, {  5, 67, }, {  5, 47, },
+		{  5, 43, }, {  5, 41, }, {  5, 37, }, {  5, 31, },
+		{  5, 29, }, {  5, 25, }, {  5, 23, }, {  5, 19, },
+		{  5, 17, }, {  5, 15, }, {  5, 13, }, {  5, 11, },
+		{  5, 10, }, {  5,  9, }, {  5,  8, }, {  4, 61, },
+		{  4, 59, }, {  4, 53, }, {  4, 47, }, {  4, 43, },
+		{  4, 41, }, {  4, 37, }, {  4, 31, }, {  4, 29, },
+		{  4, 23, }, {  4, 19, }, {  4, 17, }, {  4, 13, },
+		{  4,  9, }, {  4,  8, },
+	};
+	/* Scale the quotient for comparison to get the fractional part.  */
+	const unsigned int quot_scale = 65536;
+	unsigned int sclk = port->uartclk * 2;
+	unsigned int sdiv = DIV_ROUND_CLOSEST(sclk, baud);
+	unsigned int best_squot;
+	unsigned int squot;
+	unsigned int quot;
+	u16 cpr;
+	u8 tcr;
+	int i;
+
+	/* Old custom speed handling.  */
+	if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) {
+		unsigned int cust_div = port->custom_divisor;
+
+		quot = cust_div & UART_DIV_MAX;
+		tcr = (cust_div >> 16) & OXSEMI_TORNADO_TCR_MASK;
+		cpr = (cust_div >> 20) & OXSEMI_TORNADO_CPR_MASK;
+		if (cpr < OXSEMI_TORNADO_CPR_MIN)
+			cpr = OXSEMI_TORNADO_CPR_DEF;
+	} else {
+		best_squot = quot_scale;
+		for (i = 0; i < ARRAY_SIZE(p); i++) {
+			unsigned int spre;
+			unsigned int srem;
+			u8 cp;
+			u8 tc;
+
+			tc = p[i][0];
+			cp = p[i][1];
+			spre = tc * cp;
+
+			srem = sdiv % spre;
+			if (srem > spre / 2)
+				srem = spre - srem;
+			squot = DIV_ROUND_CLOSEST(srem * quot_scale, spre);
+
+			if (srem == 0) {
+				tcr = tc;
+				cpr = cp;
+				quot = sdiv / spre;
+				break;
+			} else if (squot < best_squot) {
+				best_squot = squot;
+				tcr = tc;
+				cpr = cp;
+				quot = DIV_ROUND_CLOSEST(sdiv, spre);
+			}
+		}
+		while (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1 &&
+		       quot % 2 == 0) {
+			quot >>= 1;
+			tcr <<= 1;
+		}
+		while (quot > UART_DIV_MAX) {
+			if (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1) {
+				quot >>= 1;
+				tcr <<= 1;
+			} else if (cpr <= OXSEMI_TORNADO_CPR_MASK >> 1) {
+				quot >>= 1;
+				cpr <<= 1;
+			} else {
+				quot = quot * cpr / OXSEMI_TORNADO_CPR_MASK;
+				cpr = OXSEMI_TORNADO_CPR_MASK;
+			}
+		}
+	}
+
+	*frac = (cpr << 8) | (tcr & OXSEMI_TORNADO_TCR_MASK);
+	return quot;
+}
+
+/*
+ * Set the oversampling rate in the transmitter clock cycle register (TCR),
+ * the clock prescaler in the clock prescaler register (CPR and CPR2), and
+ * the clock divisor in the divisor latch (DLL and DLM).  Note that for
+ * backwards compatibility any write to CPR clears CPR2 and therefore CPR
+ * has to be written first, followed by CPR2, which occupies the location
+ * of CKS used with earlier UART designs.
+ */
+static void pci_oxsemi_tornado_set_divisor(struct uart_port *port,
+					   unsigned int baud,
+					   unsigned int quot,
+					   unsigned int quot_frac)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	u8 cpr2 = quot_frac >> 16;
+	u8 cpr = quot_frac >> 8;
+	u8 tcr = quot_frac;
+
+	serial_icr_write(up, UART_TCR, tcr);
+	serial_icr_write(up, UART_CPR, cpr);
+	serial_icr_write(up, UART_CKS, cpr2);
+	serial8250_do_set_divisor(port, baud, quot, 0);
+}
+
+/*
+ * For Tornado devices we force MCR[7] set for the Divide-by-M N/8 baud rate
+ * generator prescaler (CPR and CPR2).  Otherwise no prescaler would be used.
+ */
+static void pci_oxsemi_tornado_set_mctrl(struct uart_port *port,
+					 unsigned int mctrl)
 {
-	port->bugs |= UART_BUG_PARITY;
-	return pci_default_setup(priv, board, port, idx);
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	up->mcr |= UART_MCR_CLKSEL;
+	serial8250_do_set_mctrl(port, mctrl);
+}
+
+/*
+ * We require EFR features for clock programming, so set UPF_FULL_PROBE
+ * for full probing regardless of CONFIG_SERIAL_8250_16550A_VARIANTS setting.
+ */
+static int pci_oxsemi_tornado_setup(struct serial_private *priv,
+				    const struct pciserial_board *board,
+				    struct uart_8250_port *up, int idx)
+{
+	struct pci_dev *dev = priv->dev;
+
+	if (pci_oxsemi_tornado_p(dev)) {
+		up->port.flags |= UPF_FULL_PROBE;
+		up->port.get_divisor = pci_oxsemi_tornado_get_divisor;
+		up->port.set_divisor = pci_oxsemi_tornado_set_divisor;
+		up->port.set_mctrl = pci_oxsemi_tornado_set_mctrl;
+	}
+
+	return pci_default_setup(priv, board, up, idx);
 }
 
 /* Quatech devices have their own extra interface features */
@@ -1120,15 +1300,15 @@
 	{ 0, }
 };
 
-static int pci_quatech_amcc(u16 devid)
+static int pci_quatech_amcc(struct pci_dev *dev)
 {
 	struct quatech_feature *qf = &quatech_cards[0];
 	while (qf->devid) {
-		if (qf->devid == devid)
+		if (qf->devid == dev->device)
 			return qf->amcc;
 		qf++;
 	}
-	pr_err("quatech: unknown port type '0x%04X'.\n", devid);
+	pci_err(dev, "unknown port type '0x%04X'.\n", dev->device);
 	return 0;
 };
 
@@ -1291,7 +1471,7 @@
 
 static int pci_quatech_init(struct pci_dev *dev)
 {
-	if (pci_quatech_amcc(dev->device)) {
+	if (pci_quatech_amcc(dev)) {
 		unsigned long base = pci_resource_start(dev, 0);
 		if (base) {
 			u32 tmp;
@@ -1315,7 +1495,7 @@
 	port->port.uartclk = pci_quatech_clock(port);
 	/* For now just warn about RS422 */
 	if (pci_quatech_rs422(port))
-		pr_warn("quatech: software control of RS422 features not currently supported.\n");
+		pci_warn(priv->dev, "software control of RS422 features not currently supported.\n");
 	return pci_default_setup(priv, board, port, idx);
 }
 
@@ -1349,29 +1529,33 @@
 {
 	int scr;
 	int lcr;
-	int actual_baud;
-	int tolerance;
-
-	for (scr = 5 ; scr <= 15 ; scr++) {
-		actual_baud = 921600 * 16 / scr;
-		tolerance = actual_baud / 50;
-
-		if ((baud < actual_baud + tolerance) &&
-			(baud > actual_baud - tolerance)) {
 
+	for (scr = 16; scr > 4; scr--) {
+		unsigned int maxrate = port->uartclk / scr;
+		unsigned int divisor = max(maxrate / baud, 1U);
+		int delta = maxrate / divisor - baud;
+
+		if (baud > maxrate + baud / 50)
+			continue;
+
+		if (delta > baud / 50)
+			divisor++;
+
+		if (divisor > 0xffff)
+			continue;
+
+		/* Update delta due to possible divisor change */
+		delta = maxrate / divisor - baud;
+		if (abs(delta) < baud / 50) {
 			lcr = serial_port_in(port, UART_LCR);
 			serial_port_out(port, UART_LCR, lcr | 0x80);
-
-			serial_port_out(port, UART_DLL, 1);
-			serial_port_out(port, UART_DLM, 0);
+			serial_port_out(port, UART_DLL, divisor & 0xff);
+			serial_port_out(port, UART_DLM, divisor >> 8 & 0xff);
 			serial_port_out(port, 2, 16 - scr);
 			serial_port_out(port, UART_LCR, lcr);
 			return;
-		} else if (baud > actual_baud) {
-			break;
 		}
 	}
-	serial8250_do_set_divisor(port, baud, quot, quot_frac);
 }
 static int pci_pericom_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
@@ -1465,7 +1649,7 @@
 #define FINTEK_RTS_INVERT		BIT(5)
 
 /* We should do proper H/W transceiver setting before change to RS485 mode */
-static int pci_fintek_rs485_config(struct uart_port *port,
+static int pci_fintek_rs485_config(struct uart_port *port, struct ktermios *termios,
 			       struct serial_rs485 *rs485)
 {
 	struct pci_dev *pci_dev = to_pci_dev(port->dev);
@@ -1525,7 +1709,7 @@
 	/* Get the io address from configuration space */
 	pci_read_config_word(pdev, config_base + 4, &iobase);
 
-	dev_dbg(&pdev->dev, "%s: idx=%d iobase=0x%x", __func__, idx, iobase);
+	pci_dbg(pdev, "idx=%d iobase=0x%x", idx, iobase);
 
 	port->port.iotype = UPIO_PORT;
 	port->port.iobase = iobase;
@@ -1549,7 +1733,6 @@
 	resource_size_t bar_data[3];
 	u8 config_base;
 	struct serial_private *priv = pci_get_drvdata(dev);
-	struct uart_8250_port *port;
 
 	if (!(pci_resource_flags(dev, 5) & IORESOURCE_IO) ||
 			!(pci_resource_flags(dev, 4) & IORESOURCE_IO) ||
@@ -1596,13 +1779,7 @@
 
 		pci_write_config_byte(dev, config_base + 0x06, dev->irq);
 
-		if (priv) {
-			/* re-apply RS232/485 mode when
-			 * pciserial_resume_ports()
-			 */
-			port = serial8250_get_port(priv->line[i]);
-			pci_fintek_rs485_config(&port->port, NULL);
-		} else {
+		if (!priv) {
 			/* First init without port data
 			 * force init to RS232 Mode
 			 */
@@ -1689,7 +1866,7 @@
 			struct uart_8250_port *port, int idx)
 {
 	port->port.quirks |= UPQ_NO_TXEN_TEST;
-	dev_dbg(&priv->dev->dev,
+	pci_dbg(priv->dev,
 		"serial8250: skipping TxEn test for device [%04x:%04x] subsystem [%04x:%04x]\n",
 		priv->dev->vendor, priv->dev->device,
 		priv->dev->subsystem_vendor, priv->dev->subsystem_device);
@@ -1864,6 +2041,8 @@
 #define PCI_SUBDEVICE_ID_SIIG_DUAL_30	0x2530
 #define PCI_VENDOR_ID_ADVANTECH		0x13fe
 #define PCI_DEVICE_ID_INTEL_CE4100_UART 0x2e66
+#define PCI_DEVICE_ID_ADVANTECH_PCI1600	0x1600
+#define PCI_DEVICE_ID_ADVANTECH_PCI1600_1611	0x1611
 #define PCI_DEVICE_ID_ADVANTECH_PCI3620	0x3620
 #define PCI_DEVICE_ID_ADVANTECH_PCI3618	0x3618
 #define PCI_DEVICE_ID_ADVANTECH_PCIf618	0xf618
@@ -1897,7 +2076,6 @@
 #define PCI_DEVICE_ID_WCH_CH355_4S	0x7173
 #define PCI_VENDOR_ID_AGESTAR		0x5372
 #define PCI_DEVICE_ID_AGESTAR_9375	0x6872
-#define PCI_VENDOR_ID_ASIX		0x9710
 #define PCI_DEVICE_ID_BROADCOM_TRUMANAGE 0x160a
 #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800 0x818e
 
@@ -2317,7 +2495,7 @@
 		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
-		.vendor     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
@@ -2325,6 +2503,13 @@
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
+		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+		.subvendor  = PCI_ANY_ID,
+		.subdevice  = PCI_ANY_ID,
+		.setup      = pci_pericom_setup_four_at_eight,
+	},
+	{
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
@@ -2506,7 +2691,7 @@
 		.device		= PCI_ANY_ID,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
-		.init		= pci_endrun_init,
+		.init		= pci_oxsemi_tornado_init,
 		.setup		= pci_default_setup,
 	},
 	/*
@@ -2518,7 +2703,7 @@
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.init		= pci_oxsemi_tornado_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_oxsemi_tornado_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_MAINPINE,
@@ -2526,7 +2711,7 @@
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.init		= pci_oxsemi_tornado_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_oxsemi_tornado_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_DIGI,
@@ -2534,7 +2719,170 @@
 		.subvendor		= PCI_SUBVENDOR_ID_IBM,
 		.subdevice		= PCI_ANY_ID,
 		.init			= pci_oxsemi_tornado_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	/*
+	 * Brainboxes devices - all Oxsemi based
+	 */
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4027,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4028,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4029,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4019,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4016,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4015,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x400A,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x400E,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x400C,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x400B,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x400F,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4010,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4011,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x401D,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x401E,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4013,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4017,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4018,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4026,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
+	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTASHIELD,
+		.device		= 0x4021,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_oxsemi_tornado_init,
+		.setup		= pci_oxsemi_tornado_setup,
 	},
 	{
 		.vendor         = PCI_VENDOR_ID_INTEL,
@@ -2701,16 +3049,6 @@
 		.setup          = pci_wch_ch38x_setup,
 	},
 	/*
-	 * ASIX devices with FIFO bug
-	 */
-	{
-		.vendor		= PCI_VENDOR_ID_ASIX,
-		.device		= PCI_ANY_ID,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_asix_setup,
-	},
-	/*
 	 * Broadcom TruManage (NetXtreme)
 	 */
 	{
@@ -2851,7 +3189,7 @@
 	pbn_b0_2_1843200,
 	pbn_b0_4_1843200,
 
-	pbn_b0_1_3906250,
+	pbn_b0_1_15625000,
 
 	pbn_b0_bt_1_115200,
 	pbn_b0_bt_2_115200,
@@ -2929,12 +3267,11 @@
 	pbn_panacom2,
 	pbn_panacom4,
 	pbn_plx_romulus,
-	pbn_endrun_2_4000000,
 	pbn_oxsemi,
-	pbn_oxsemi_1_3906250,
-	pbn_oxsemi_2_3906250,
-	pbn_oxsemi_4_3906250,
-	pbn_oxsemi_8_3906250,
+	pbn_oxsemi_1_15625000,
+	pbn_oxsemi_2_15625000,
+	pbn_oxsemi_4_15625000,
+	pbn_oxsemi_8_15625000,
 	pbn_intel_i960,
 	pbn_sgi_ioc3,
 	pbn_computone_4,
@@ -3081,10 +3418,10 @@
 		.uart_offset	= 8,
 	},
 
-	[pbn_b0_1_3906250] = {
+	[pbn_b0_1_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 8,
 	},
 
@@ -3456,20 +3793,6 @@
 	},
 
 	/*
-	 * EndRun Technologies
-	* Uses the size of PCI Base region 0 to
-	* signal now many ports are available
-	* 2 port 952 Uart support
-	*/
-	[pbn_endrun_2_4000000] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 2,
-		.base_baud	= 4000000,
-		.uart_offset	= 0x200,
-		.first_offset	= 0x1000,
-	},
-
-	/*
 	 * This board uses the size of PCI Base region 0 to
 	 * signal now many ports are available
 	 */
@@ -3479,31 +3802,31 @@
 		.base_baud	= 115200,
 		.uart_offset	= 8,
 	},
-	[pbn_oxsemi_1_3906250] = {
+	[pbn_oxsemi_1_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
-	[pbn_oxsemi_2_3906250] = {
+	[pbn_oxsemi_2_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 2,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
-	[pbn_oxsemi_4_3906250] = {
+	[pbn_oxsemi_4_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 4,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
-	[pbn_oxsemi_8_3906250] = {
+	[pbn_oxsemi_8_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 8,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
@@ -4000,12 +4323,12 @@
 		uart.port.irq = 0;
 	} else {
 		if (pci_match_id(pci_use_msi, dev)) {
-			dev_dbg(&dev->dev, "Using MSI(-X) interrupts\n");
+			pci_dbg(dev, "Using MSI(-X) interrupts\n");
 			pci_set_master(dev);
 			uart.port.flags &= ~UPF_SHARE_IRQ;
 			rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES);
 		} else {
-			dev_dbg(&dev->dev, "Using legacy interrupts\n");
+			pci_dbg(dev, "Using legacy interrupts\n");
 			rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_LEGACY);
 		}
 		if (rc < 0) {
@@ -4023,12 +4346,12 @@
 		if (quirk->setup(priv, board, &uart, i))
 			break;
 
-		dev_dbg(&dev->dev, "Setup PCI port: port %lx, irq %d, type %d\n",
+		pci_dbg(dev, "Setup PCI port: port %lx, irq %d, type %d\n",
 			uart.port.iobase, uart.port.irq, uart.port.iotype);
 
 		priv->line[i] = serial8250_register_8250_port(&uart);
 		if (priv->line[i] < 0) {
-			dev_err(&dev->dev,
+			pci_err(dev,
 				"Couldn't register serial port %lx, irq %d, type %d, error %d\n",
 				uart.port.iobase, uart.port.irq,
 				uart.port.iotype, priv->line[i]);
@@ -4124,8 +4447,7 @@
 	}
 
 	if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
-		dev_err(&dev->dev, "invalid driver_data: %ld\n",
-			ent->driver_data);
+		pci_err(dev, "invalid driver_data: %ld\n", ent->driver_data);
 		return -EINVAL;
 	}
 
@@ -4208,7 +4530,7 @@
 		err = pci_enable_device(pdev);
 		/* FIXME: We cannot simply error out here */
 		if (err)
-			dev_err(dev, "Unable to re-enable ports, trying to continue.\n");
+			pci_err(pdev, "Unable to re-enable ports, trying to continue.\n");
 		pciserial_resume_ports(priv);
 	}
 	return 0;
@@ -4219,6 +4541,9 @@
 			 pciserial_resume_one);
 
 static const struct pci_device_id serial_pci_tbl[] = {
+	{	PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI1600,
+		PCI_DEVICE_ID_ADVANTECH_PCI1600_1611, PCI_ANY_ID, 0, 0,
+		pbn_b0_4_921600 },
 	/* Advantech use PCI_DEVICE_ID_ADVANTECH_PCI3620 (0x3620) as 'PCI_SUBVENDOR_ID' */
 	{	PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620,
 		PCI_DEVICE_ID_ADVANTECH_PCI3620, 0x0001, 0, 0,
@@ -4402,13 +4727,6 @@
 		0x10b5, 0x106a, 0, 0,
 		pbn_plx_romulus },
 	/*
-	* EndRun Technologies. PCI express device range.
-	*    EndRun PTP/1588 has 2 Native UARTs.
-	*/
-	{	PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
-		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_endrun_2_4000000 },
-	/*
 	 * Quatech cards. These actually have configurable clocks but for
 	 * now we just use the default.
 	 *
@@ -4517,158 +4835,165 @@
 	 */
 	{	PCI_VENDOR_ID_OXSEMI, 0xc101,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc105,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc11b,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc11f,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc120,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc124,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc138,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc13d,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc140,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc141,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc144,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc145,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc158,    /* OXPCIe952 2 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc15d,    /* OXPCIe952 2 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc208,    /* OXPCIe954 4 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_4_3906250 },
+		pbn_oxsemi_4_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc20d,    /* OXPCIe954 4 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_4_3906250 },
+		pbn_oxsemi_4_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc308,    /* OXPCIe958 8 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_8_3906250 },
+		pbn_oxsemi_8_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc30d,    /* OXPCIe958 8 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_8_3906250 },
+		pbn_oxsemi_8_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc40b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc40f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc41b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc41f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc42b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc42f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc43b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc43f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc44b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc44f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc45b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc45f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc46b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc46f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc47b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc47f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc48b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc48f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc49b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc49f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4ab,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4af,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4bb,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4bf,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4cb,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4cf,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	/*
 	 * Mainpine Inc. IQ Express "Rev3" utilizing OxSemi Tornado
 	 */
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 1 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4001, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 2 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4002, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 4 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4004, 0, 0,
-		pbn_oxsemi_4_3906250 },
+		pbn_oxsemi_4_15625000 },
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 8 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4008, 0, 0,
-		pbn_oxsemi_8_3906250 },
+		pbn_oxsemi_8_15625000 },
 
 	/*
 	 * Digi/IBM PCIe 2-port Async EIA-232 Adapter utilizing OxSemi Tornado
 	 */
 	{	PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_2_OX_IBM,
 		PCI_SUBVENDOR_ID_IBM, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * EndRun Technologies. PCI express device range.
+	 * EndRun PTP/1588 has 2 Native UARTs utilizing OxSemi 952.
+	 */
+	{	PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+		pbn_oxsemi_2_15625000 },
 
 	/*
 	 * SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards,
@@ -5181,6 +5506,12 @@
 		pbn_b1_bt_1_115200 },
 
 	/*
+	 * IntaShield IS-100
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0D60,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+		pbn_b2_1_115200 },
+	/*
 	 * IntaShield IS-200
 	 */
 	{	PCI_VENDOR_ID_INTASHIELD, PCI_DEVICE_ID_INTASHIELD_IS200,
@@ -5193,7 +5524,62 @@
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,    /* 135a.0dc0 */
 		pbn_b2_4_115200 },
 	/*
-	 * BrainBoxes UC-260
+	 * IntaShield IX-100
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4027,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+	/*
+	 * IntaShield IX-200
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4028,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * IntaShield IX-400
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4029,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_4_15625000 },
+	/* Brainboxes Devices */
+	/*
+	* Brainboxes UC-101
+	*/
+	{       PCI_VENDOR_ID_INTASHIELD, 0x0BA1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{       PCI_VENDOR_ID_INTASHIELD, 0x0BA2,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{       PCI_VENDOR_ID_INTASHIELD, 0x0BA3,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-235/246
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0AA1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_1_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0AA2,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_1_115200 },
+	/*
+	 * Brainboxes UC-253/UC-734
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0CA1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-260/271/701/756
 	 */
 	{	PCI_VENDOR_ID_INTASHIELD, 0x0D21,
 		PCI_ANY_ID, PCI_ANY_ID,
@@ -5201,8 +5587,348 @@
 		pbn_b2_4_115200 },
 	{	PCI_VENDOR_ID_INTASHIELD, 0x0E34,
 		PCI_ANY_ID, PCI_ANY_ID,
-		 PCI_CLASS_COMMUNICATION_MULTISERIAL << 8, 0xffff00,
+		PCI_CLASS_COMMUNICATION_MULTISERIAL << 8, 0xffff00,
+		pbn_b2_4_115200 },
+	/*
+	 * Brainboxes UC-268
+	 */
+	{       PCI_VENDOR_ID_INTASHIELD, 0x0841,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	/*
+	 * Brainboxes UC-275/279
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0881,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_8_115200 },
+	/*
+	 * Brainboxes UC-302
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x08E1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x08E2,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x08E3,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-310
+	 */
+	{       PCI_VENDOR_ID_INTASHIELD, 0x08C1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-313
+	 */
+	{       PCI_VENDOR_ID_INTASHIELD, 0x08A1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{       PCI_VENDOR_ID_INTASHIELD, 0x08A2,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{       PCI_VENDOR_ID_INTASHIELD, 0x08A3,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-320/324
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0A61,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_1_115200 },
+	/*
+	 * Brainboxes UC-346
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0B01,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0B02,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	/*
+	 * Brainboxes UC-357
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0A81,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0A82,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0A83,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-368
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C41,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
 		pbn_b2_4_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C42,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C43,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	/*
+	 * Brainboxes UC-420
+	 */
+	{       PCI_VENDOR_ID_INTASHIELD, 0x0921,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	/*
+	 * Brainboxes UC-607
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x09A1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x09A2,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x09A3,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UC-836
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0D41,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_4_115200 },
+	/*
+	 * Brainboxes UP-189
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0AC1,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0AC2,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0AC3,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UP-200
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0B21,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0B22,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0B23,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UP-869
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C01,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C02,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C03,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes UP-880
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C21,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C22,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0C23,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_2_115200 },
+	/*
+	 * Brainboxes PX-101
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4005,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4019,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * Brainboxes PX-235/246
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4004,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_1_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4016,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+	/*
+	 * Brainboxes PX-203/PX-257
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4006,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4015,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * Brainboxes PX-260/PX-701
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x400A,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_4_15625000 },
+	/*
+	 * Brainboxes PX-275/279
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x0E41,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b2_8_115200 },
+	/*
+	 * Brainboxes PX-310
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x400E,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * Brainboxes PX-313
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x400C,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * Brainboxes PX-320/324/PX-376/PX-387
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x400B,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+	/*
+	 * Brainboxes PX-335/346
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x400F,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_4_15625000 },
+	/*
+	 * Brainboxes PX-368
+	 */
+	{       PCI_VENDOR_ID_INTASHIELD, 0x4010,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_4_15625000 },
+	/*
+	 * Brainboxes PX-420
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4000,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_4_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4011,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_4_15625000 },
+	/*
+	 * Brainboxes PX-475
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x401D,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+	/*
+	 * Brainboxes PX-803/PX-857
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4009,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_2_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4018,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x401E,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_2_15625000 },
+	/*
+	 * Brainboxes PX-820
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4002,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_4_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4013,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_4_15625000 },
+	/*
+	 * Brainboxes PX-846
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4008,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b0_1_115200 },
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4017,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+	/*
+	 * Brainboxes XC-235
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4026,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+	/*
+	 * Brainboxes XC-475
+	 */
+	{	PCI_VENDOR_ID_INTASHIELD, 0x4021,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_oxsemi_1_15625000 },
+
 	/*
 	 * Perle PCI-RAS cards
 	 */
@@ -5621,6 +6347,14 @@
 	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
 		0xA000, 0x3004,
 		0, 0, pbn_b0_bt_4_115200 },
+
+	/*
+	 * ASIX AX99100 PCIe to Multi I/O Controller
+	 */
+	{	PCI_VENDOR_ID_ASIX, PCI_DEVICE_ID_ASIX_AX99100,
+		0xA000, 0x1000,
+		0, 0, pbn_b0_1_115200 },
+
 	/* Intel CE4100 */
 	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CE4100_UART,
 		PCI_ANY_ID,  PCI_ANY_ID, 0, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_port.c
@@ -15,6 +15,7 @@
 #include <linux/moduleparam.h>
 #include <linux/ioport.h>
 #include <linux/init.h>
+#include <linux/irq.h>
 #include <linux/console.h>
 #include <linux/gpio/consumer.h>
 #include <linux/sysrq.h>
@@ -307,6 +308,14 @@
 		.rxtrig_bytes	= {1, 32, 64, 112},
 		.flags		= UART_CAP_FIFO | UART_CAP_SLEEP,
 	},
+	[PORT_ASPEED_VUART] = {
+		.name		= "ASPEED VUART",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO,
+	},
 };
 
 /* Uart divisor latch read */
@@ -530,27 +539,6 @@
 }
 
 /*
- * For the 16C950
- */
-static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
-{
-	serial_out(up, UART_SCR, offset);
-	serial_out(up, UART_ICR, value);
-}
-
-static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
-{
-	unsigned int value;
-
-	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
-	serial_out(up, UART_SCR, offset);
-	value = serial_in(up, UART_ICR);
-	serial_icr_write(up, UART_ACR, up->acr);
-
-	return value;
-}
-
-/*
  * FIFO support.
  */
 static void serial8250_clear_fifos(struct uart_8250_port *p)
@@ -613,7 +601,7 @@
 static int serial8250_em485_init(struct uart_8250_port *p)
 {
 	if (p->em485)
-		return 0;
+		goto deassert_rts;
 
 	p->em485 = kmalloc(sizeof(struct uart_8250_em485), GFP_ATOMIC);
 	if (!p->em485)
@@ -629,7 +617,9 @@
 	p->em485->active_timer = NULL;
 	p->em485->tx_stopped = true;
 
-	p->rs485_stop_tx(p);
+deassert_rts:
+	if (p->em485->tx_stopped)
+		p->rs485_stop_tx(p);
 
 	return 0;
 }
@@ -663,13 +653,15 @@
 /**
  * serial8250_em485_config() - generic ->rs485_config() callback
  * @port: uart port
+ * @termios: termios structure
  * @rs485: rs485 settings
  *
  * Generic callback usable by 8250 uart drivers to activate rs485 settings
  * if the uart is incapable of driving RTS as a Transmit Enable signal in
  * hardware, relying on software emulation instead.
  */
-int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485)
+int serial8250_em485_config(struct uart_port *port, struct ktermios *termios,
+			    struct serial_rs485 *rs485)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 
@@ -680,13 +672,6 @@
 		rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
 	}
 
-	/* clamp the delays to [0, 100ms] */
-	rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U);
-	rs485->delay_rts_after_send  = min(rs485->delay_rts_after_send, 100U);
-
-	memset(rs485->padding, 0, sizeof(rs485->padding));
-	port->rs485 = *rs485;
-
 	gpiod_set_value(port->rs485_term_gpio,
 			rs485->flags & SER_RS485_TERMINATE_BUS);
 
@@ -694,15 +679,8 @@
 	 * Both serial8250_em485_init() and serial8250_em485_destroy()
 	 * are idempotent.
 	 */
-	if (rs485->flags & SER_RS485_ENABLED) {
-		int ret = serial8250_em485_init(up);
-
-		if (ret) {
-			rs485->flags &= ~SER_RS485_ENABLED;
-			port->rs485.flags &= ~SER_RS485_ENABLED;
-		}
-		return ret;
-	}
+	if (rs485->flags & SER_RS485_ENABLED)
+		return serial8250_em485_init(up);
 
 	serial8250_em485_destroy(up);
 	return 0;
@@ -1042,7 +1020,8 @@
 	up->port.type = PORT_16550A;
 	up->capabilities |= UART_CAP_FIFO;
 
-	if (!IS_ENABLED(CONFIG_SERIAL_8250_16550A_VARIANTS))
+	if (!IS_ENABLED(CONFIG_SERIAL_8250_16550A_VARIANTS) &&
+	    !(up->port.flags & UPF_FULL_PROBE))
 		return;
 
 	/*
@@ -1389,9 +1368,6 @@
 		inb_p(ICP);
 	}
 
-	if (uart_console(port))
-		console_lock();
-
 	/* forget possible initially masked and pending IRQ */
 	probe_irq_off(probe_irq_on());
 	save_mcr = serial8250_in_MCR(up);
@@ -1422,9 +1398,6 @@
 	if (port->flags & UPF_FOURPORT)
 		outb_p(save_ICP, ICP);
 
-	if (uart_console(port))
-		console_unlock();
-
 	port->irq = (irq > 0) ? irq : 0;
 }
 
@@ -1527,6 +1500,8 @@
 
 	if (em485) {
 		unsigned char lsr = serial_in(p, UART_LSR);
+		p->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+
 		/*
 		 * To provide required timeing and allow FIFO transfer,
 		 * __stop_tx_rs485() must be called only when both FIFO and
@@ -1615,6 +1590,18 @@
 	struct uart_8250_port *up = up_to_u8250p(port);
 	struct uart_8250_em485 *em485 = up->em485;
 
+	/*
+	 * While serial8250_em485_handle_stop_tx() is a noop if
+	 * em485->active_timer != &em485->stop_tx_timer, it might happen that
+	 * the timer is still armed and triggers only after the current bunch of
+	 * chars is send and em485->active_timer == &em485->stop_tx_timer again.
+	 * So cancel the timer. There is still a theoretical race condition if
+	 * the timer is already running and only comes around to check for
+	 * em485->active_timer when &em485->stop_tx_timer is armed again.
+	 */
+	if (em485->active_timer == &em485->stop_tx_timer)
+		hrtimer_try_to_cancel(&em485->stop_tx_timer);
+
 	em485->active_timer = NULL;
 
 	if (em485->tx_stopped) {
@@ -1799,9 +1786,7 @@
 	int count;
 
 	if (port->x_char) {
-		serial_out(up, UART_TX, port->x_char);
-		port->icount.tx++;
-		port->x_char = 0;
+		uart_xchar_out(port, UART_TX);
 		return;
 	}
 	if (uart_tx_stopped(port)) {
@@ -1883,10 +1868,13 @@
 static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
 {
 	switch (iir & 0x3f) {
-	case UART_IIR_RX_TIMEOUT:
-		serial8250_rx_dma_flush(up);
+	case UART_IIR_RDI:
+		if (!up->dma->rx_running)
+			break;
 		fallthrough;
 	case UART_IIR_RLSI:
+	case UART_IIR_RX_TIMEOUT:
+		serial8250_rx_dma_flush(up);
 		return true;
 	}
 	return up->dma->rx_dma(up);
@@ -1899,6 +1887,7 @@
 {
 	unsigned char status;
 	struct uart_8250_port *up = up_to_u8250p(port);
+	struct tty_port *tport = &port->state->port;
 	bool skip_rx = false;
 	unsigned long flags;
 
@@ -1923,6 +1912,11 @@
 		skip_rx = true;
 
 	if (status & (UART_LSR_DR | UART_LSR_BI) && !skip_rx) {
+		struct irq_data *d;
+
+		d = irq_get_irq_data(port->irq);
+		if (d && irqd_is_wakeup_set(d))
+			pm_wakeup_event(tport->tty->dev, 0);
 		if (!up->dma || handle_rx_dma(up, iir))
 			status = serial8250_rx_chars(up, status);
 	}
@@ -1979,19 +1973,25 @@
 static unsigned int serial8250_tx_empty(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned int result = 0;
 	unsigned long flags;
 	unsigned int lsr;
 
 	serial8250_rpm_get(up);
 
 	spin_lock_irqsave(&port->lock, flags);
-	lsr = serial_port_in(port, UART_LSR);
-	up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+	if (!serial8250_tx_dma_running(up)) {
+		lsr = serial_port_in(port, UART_LSR);
+		up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+
+		if ((lsr & BOTH_EMPTY) == BOTH_EMPTY)
+			result = TIOCSER_TEMT;
+	}
 	spin_unlock_irqrestore(&port->lock, flags);
 
 	serial8250_rpm_put(up);
 
-	return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
+	return result;
 }
 
 unsigned int serial8250_do_get_mctrl(struct uart_port *port)
@@ -2024,13 +2024,6 @@
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned char mcr;
 
-	if (port->rs485.flags & SER_RS485_ENABLED) {
-		if (serial8250_in_MCR(up) & UART_MCR_RTS)
-			mctrl |= TIOCM_RTS;
-		else
-			mctrl &= ~TIOCM_RTS;
-	}
-
 	mcr = serial8250_TIOCM_to_MCR(mctrl);
 
 	mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
@@ -2041,6 +2034,9 @@
 
 static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
+	if (port->rs485.flags & SER_RS485_ENABLED)
+		return;
+
 	if (port->set_mctrl)
 		port->set_mctrl(port, mctrl);
 	else
@@ -2287,6 +2283,10 @@
 	if (port->irq && (up->port.flags & UPF_SHARE_IRQ))
 		up->port.irqflags |= IRQF_SHARED;
 
+	retval = up->ops->setup_irq(up);
+	if (retval)
+		goto out;
+
 	if (port->irq && !(up->port.flags & UPF_NO_THRE_TEST)) {
 		unsigned char iir1;
 
@@ -2329,9 +2329,7 @@
 		}
 	}
 
-	retval = up->ops->setup_irq(up);
-	if (retval)
-		goto out;
+	up->ops->setup_timer(up);
 
 	/*
 	 * Now, initialize the UART
@@ -2516,6 +2514,14 @@
 	return DIV_ROUND_CLOSEST(port->uartclk, 16 * baud + 2) - 2;
 }
 
+static void serial8250_flush_buffer(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	if (up->dma)
+		serial8250_tx_dma_flush(up);
+}
+
 static unsigned int serial8250_do_get_divisor(struct uart_port *port,
 					      unsigned int baud,
 					      unsigned int *frac)
@@ -2607,11 +2613,8 @@
 
 	if (c_cflag & CSTOPB)
 		cval |= UART_LCR_STOP;
-	if (c_cflag & PARENB) {
+	if (c_cflag & PARENB)
 		cval |= UART_LCR_PARITY;
-		if (up->bugs & UART_BUG_PARITY)
-			up->fifo_bug = true;
-	}
 	if (!(c_cflag & PARODD))
 		cval |= UART_LCR_EPAR;
 #ifdef CMSPAR
@@ -2696,21 +2699,32 @@
 void serial8250_update_uartclk(struct uart_port *port, unsigned int uartclk)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
+	struct tty_port *tport = &port->state->port;
 	unsigned int baud, quot, frac = 0;
 	struct ktermios *termios;
+	struct tty_struct *tty;
 	unsigned long flags;
 
-	mutex_lock(&port->state->port.mutex);
+	tty = tty_port_tty_get(tport);
+	if (!tty) {
+		mutex_lock(&tport->mutex);
+		port->uartclk = uartclk;
+		mutex_unlock(&tport->mutex);
+		return;
+	}
+
+	down_write(&tty->termios_rwsem);
+	mutex_lock(&tport->mutex);
 
 	if (port->uartclk == uartclk)
 		goto out_lock;
 
 	port->uartclk = uartclk;
 
-	if (!tty_port_initialized(&port->state->port))
+	if (!tty_port_initialized(tport))
 		goto out_lock;
 
-	termios = &port->state->port.tty->termios;
+	termios = &tty->termios;
 
 	baud = serial8250_get_baud_rate(port, termios, NULL);
 	quot = serial8250_get_divisor(port, baud, &frac);
@@ -2727,7 +2741,9 @@
 	serial8250_rpm_put(up);
 
 out_lock:
-	mutex_unlock(&port->state->port.mutex);
+	mutex_unlock(&tport->mutex);
+	up_write(&tty->termios_rwsem);
+	tty_kref_put(tty);
 }
 EXPORT_SYMBOL_GPL(serial8250_update_uartclk);
 
@@ -2761,8 +2777,7 @@
 	up->lcr = cval;					/* Save computed LCR */
 
 	if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
-		/* NOTE: If fifo_bug is not set, a user can set RX_trigger. */
-		if ((baud < 2400 && !up->dma) || up->fifo_bug) {
+		if (baud < 2400 && !up->dma) {
 			up->fcr &= ~UART_FCR_TRIGGER_MASK;
 			up->fcr |= UART_FCR_TRIGGER_1;
 		}
@@ -2956,8 +2971,10 @@
 	case UPIO_MEM32BE:
 	case UPIO_MEM16:
 	case UPIO_MEM:
-		if (!port->mapbase)
+		if (!port->mapbase) {
+			ret = -EINVAL;
 			break;
+		}
 
 		if (!request_mem_region(port->mapbase, size, "serial")) {
 			ret = -EBUSY;
@@ -3096,8 +3113,7 @@
 	struct uart_8250_port *up = up_to_u8250p(uport);
 	int rxtrig;
 
-	if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 ||
-	    up->fifo_bug)
+	if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1)
 		return -EINVAL;
 
 	rxtrig = bytes_to_fcr_rxtrig(up, bytes);
@@ -3181,9 +3197,6 @@
 	if (flags & UART_CONFIG_TYPE)
 		autoconfig(up);
 
-	if (port->rs485.flags & SER_RS485_ENABLED)
-		port->rs485_config(port, &port->rs485);
-
 	/* if access method is AU, it is a 16550 with a quirk */
 	if (port->type == PORT_16550A && port->iotype == UPIO_AU)
 		up->bugs |= UART_BUG_NOMSR;
@@ -3235,6 +3248,7 @@
 	.break_ctl	= serial8250_break_ctl,
 	.startup	= serial8250_startup,
 	.shutdown	= serial8250_shutdown,
+	.flush_buffer	= serial8250_flush_buffer,
 	.set_termios	= serial8250_set_termios,
 	.set_ldisc	= serial8250_set_ldisc,
 	.pm		= serial8250_pm,
@@ -3254,6 +3268,7 @@
 	struct uart_port *port = &up->port;
 
 	spin_lock_init(&port->lock);
+	port->pm = NULL;
 	port->ops = &serial8250_pops;
 	port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE);
 
@@ -3308,15 +3323,20 @@
 	unsigned int baud, quot, frac = 0;
 
 	termios.c_cflag = port->cons->cflag;
-	if (port->state->port.tty && termios.c_cflag == 0)
+	termios.c_ispeed = port->cons->ispeed;
+	termios.c_ospeed = port->cons->ospeed;
+	if (port->state->port.tty && termios.c_cflag == 0) {
 		termios.c_cflag = port->state->port.tty->termios.c_cflag;
+		termios.c_ispeed = port->state->port.tty->termios.c_ispeed;
+		termios.c_ospeed = port->state->port.tty->termios.c_ospeed;
+	}
 
 	baud = serial8250_get_baud_rate(port, &termios, NULL);
 	quot = serial8250_get_divisor(port, baud, &frac);
 
 	serial8250_set_divisor(port, baud, quot, frac);
 	serial_port_out(port, UART_LCR, up->lcr);
-	serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
+	serial8250_out_MCR(up, up->mcr | UART_MCR_DTR | UART_MCR_RTS);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_pxa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_pxa.c
@@ -125,6 +125,7 @@
 	uart.port.regshift = 2;
 	uart.port.irq = irq;
 	uart.port.fifosize = 64;
+	uart.tx_loadsz = 32;
 	uart.port.flags = UPF_IOREMAP | UPF_SKIP_TEST | UPF_FIXED_TYPE;
 	uart.port.dev = &pdev->dev;
 	uart.port.uartclk = clk_get_rate(data->clk);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/8250_tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/8250_tegra.c
@@ -112,13 +112,15 @@
 
 	ret = serial8250_register_8250_port(&port8250);
 	if (ret < 0)
-		goto err_clkdisable;
+		goto err_ctrl_assert;
 
 	platform_set_drvdata(pdev, uart);
 	uart->line = ret;
 
 	return 0;
 
+err_ctrl_assert:
+	reset_control_assert(uart->rst);
 err_clkdisable:
 	clk_disable_unprepare(uart->clk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/8250/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/8250/Kconfig
@@ -118,7 +118,7 @@
 
 config SERIAL_8250_GSC
 	tristate
-	depends on SERIAL_8250 && GSC
+	depends on SERIAL_8250 && PARISC
 	default SERIAL_8250
 
 config SERIAL_8250_DMA
@@ -253,7 +253,9 @@
 	tristate "Aspeed Virtual UART"
 	depends on SERIAL_8250
 	depends on OF
-	depends on REGMAP && MFD_SYSCON
+	depends on MFD_SYSCON
+	depends on ARCH_ASPEED || COMPILE_TEST
+	select REGMAP
 	help
 	  If you want to use the virtual UART (VUART) device on Aspeed
 	  BMC platforms, enable this option. This enables the 16550A-
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/Kconfig
@@ -531,7 +531,7 @@
 	int "Maximum number of uartlite serial ports"
 	depends on SERIAL_UARTLITE
 	range 1 256
-	default 1
+	default 16
 	help
 	  Set this to the number of uartlites in your system, or the number
 	  you think you might implement.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/altera_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/altera_uart.c
@@ -199,9 +199,8 @@
 	 */
 }
 
-static void altera_uart_rx_chars(struct altera_uart *pp)
+static void altera_uart_rx_chars(struct uart_port *port)
 {
-	struct uart_port *port = &pp->port;
 	unsigned char ch, flag;
 	unsigned short status;
 
@@ -246,9 +245,8 @@
 	tty_flip_buffer_push(&port->state->port);
 }
 
-static void altera_uart_tx_chars(struct altera_uart *pp)
+static void altera_uart_tx_chars(struct uart_port *port)
 {
-	struct uart_port *port = &pp->port;
 	struct circ_buf *xmit = &port->state->xmit;
 
 	if (port->x_char) {
@@ -272,26 +270,25 @@
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(port);
 
-	if (xmit->head == xmit->tail) {
-		pp->imr &= ~ALTERA_UART_CONTROL_TRDY_MSK;
-		altera_uart_update_ctrl_reg(pp);
-	}
+	if (uart_circ_empty(xmit))
+		altera_uart_stop_tx(port);
 }
 
 static irqreturn_t altera_uart_interrupt(int irq, void *data)
 {
 	struct uart_port *port = data;
 	struct altera_uart *pp = container_of(port, struct altera_uart, port);
+	unsigned long flags;
 	unsigned int isr;
 
 	isr = altera_uart_readl(port, ALTERA_UART_STATUS_REG) & pp->imr;
 
-	spin_lock(&port->lock);
+	spin_lock_irqsave(&port->lock, flags);
 	if (isr & ALTERA_UART_STATUS_RRDY_MSK)
-		altera_uart_rx_chars(pp);
+		altera_uart_rx_chars(port);
 	if (isr & ALTERA_UART_STATUS_TRDY_MSK)
-		altera_uart_tx_chars(pp);
-	spin_unlock(&port->lock);
+		altera_uart_tx_chars(port);
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	return IRQ_RETVAL(isr);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/amba-pl010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/amba-pl010.c
@@ -446,14 +446,11 @@
 	if ((termios->c_cflag & CREAD) == 0)
 		uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
 
-	/* first, disable everything */
 	old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
 
 	if (UART_ENABLE_MS(port, termios->c_cflag))
 		old_cr |= UART010_CR_MSIE;
 
-	writel(0, uap->port.membase + UART010_CR);
-
 	/* Set baud rate */
 	quot -= 1;
 	writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/amba-pl011.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/amba-pl011.c
@@ -222,17 +222,18 @@
 
 /* Deals with DMA transactions */
 
-struct pl011_sgbuf {
-	struct scatterlist sg;
-	char *buf;
+struct pl011_dmabuf {
+	dma_addr_t		dma;
+	size_t			len;
+	char			*buf;
 };
 
 struct pl011_dmarx_data {
 	struct dma_chan		*chan;
 	struct completion	complete;
 	bool			use_buf_b;
-	struct pl011_sgbuf	sgbuf_a;
-	struct pl011_sgbuf	sgbuf_b;
+	struct pl011_dmabuf	dbuf_a;
+	struct pl011_dmabuf	dbuf_b;
 	dma_cookie_t		cookie;
 	bool			running;
 	struct timer_list	timer;
@@ -245,7 +246,8 @@
 
 struct pl011_dmatx_data {
 	struct dma_chan		*chan;
-	struct scatterlist	sg;
+	dma_addr_t		dma;
+	size_t			len;
 	char			*buf;
 	bool			queued;
 };
@@ -349,9 +351,9 @@
 				flag = TTY_FRAME;
 		}
 
-		spin_unlock(&uap->port.lock);
+		uart_port_unlock(&uap->port);
 		sysrq = uart_handle_sysrq_char(&uap->port, ch & 255);
-		spin_lock(&uap->port.lock);
+		uart_port_lock(&uap->port);
 
 		if (!sysrq)
 			uart_insert_char(&uap->port, ch, UART011_DR_OE, ch, flag);
@@ -370,32 +372,24 @@
 
 #define PL011_DMA_BUFFER_SIZE PAGE_SIZE
 
-static int pl011_sgbuf_init(struct dma_chan *chan, struct pl011_sgbuf *sg,
+static int pl011_dmabuf_init(struct dma_chan *chan, struct pl011_dmabuf *db,
 	enum dma_data_direction dir)
 {
-	dma_addr_t dma_addr;
-
-	sg->buf = dma_alloc_coherent(chan->device->dev,
-		PL011_DMA_BUFFER_SIZE, &dma_addr, GFP_KERNEL);
-	if (!sg->buf)
+	db->buf = dma_alloc_coherent(chan->device->dev, PL011_DMA_BUFFER_SIZE,
+				     &db->dma, GFP_KERNEL);
+	if (!db->buf)
 		return -ENOMEM;
-
-	sg_init_table(&sg->sg, 1);
-	sg_set_page(&sg->sg, phys_to_page(dma_addr),
-		PL011_DMA_BUFFER_SIZE, offset_in_page(dma_addr));
-	sg_dma_address(&sg->sg) = dma_addr;
-	sg_dma_len(&sg->sg) = PL011_DMA_BUFFER_SIZE;
+	db->len = PL011_DMA_BUFFER_SIZE;
 
 	return 0;
 }
 
-static void pl011_sgbuf_free(struct dma_chan *chan, struct pl011_sgbuf *sg,
+static void pl011_dmabuf_free(struct dma_chan *chan, struct pl011_dmabuf *db,
 	enum dma_data_direction dir)
 {
-	if (sg->buf) {
+	if (db->buf) {
 		dma_free_coherent(chan->device->dev,
-			PL011_DMA_BUFFER_SIZE, sg->buf,
-			sg_dma_address(&sg->sg));
+				  PL011_DMA_BUFFER_SIZE, db->buf, db->dma);
 	}
 }
 
@@ -554,10 +548,10 @@
 	unsigned long flags;
 	u16 dmacr;
 
-	spin_lock_irqsave(&uap->port.lock, flags);
+	uart_port_lock_irqsave(&uap->port, &flags);
 	if (uap->dmatx.queued)
-		dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1,
-			     DMA_TO_DEVICE);
+		dma_unmap_single(dmatx->chan->device->dev, dmatx->dma,
+				dmatx->len, DMA_TO_DEVICE);
 
 	dmacr = uap->dmacr;
 	uap->dmacr = dmacr & ~UART011_TXDMAE;
@@ -575,7 +569,7 @@
 	if (!(dmacr & UART011_TXDMAE) || uart_tx_stopped(&uap->port) ||
 	    uart_circ_empty(&uap->port.state->xmit)) {
 		uap->dmatx.queued = false;
-		spin_unlock_irqrestore(&uap->port.lock, flags);
+		uart_port_unlock_irqrestore(&uap->port, flags);
 		return;
 	}
 
@@ -586,7 +580,7 @@
 		 */
 		pl011_start_tx_pio(uap);
 
-	spin_unlock_irqrestore(&uap->port.lock, flags);
+	uart_port_unlock_irqrestore(&uap->port, flags);
 }
 
 /*
@@ -643,18 +637,19 @@
 			memcpy(&dmatx->buf[first], &xmit->buf[0], second);
 	}
 
-	dmatx->sg.length = count;
-
-	if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) {
+	dmatx->len = count;
+	dmatx->dma = dma_map_single(dma_dev->dev, dmatx->buf, count,
+				    DMA_TO_DEVICE);
+	if (dmatx->dma == DMA_MAPPING_ERROR) {
 		uap->dmatx.queued = false;
 		dev_dbg(uap->port.dev, "unable to map TX DMA\n");
 		return -EBUSY;
 	}
 
-	desc = dmaengine_prep_slave_sg(chan, &dmatx->sg, 1, DMA_MEM_TO_DEV,
+	desc = dmaengine_prep_slave_single(chan, dmatx->dma, dmatx->len, DMA_MEM_TO_DEV,
 					     DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!desc) {
-		dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE);
+		dma_unmap_single(dma_dev->dev, dmatx->dma, dmatx->len, DMA_TO_DEVICE);
 		uap->dmatx.queued = false;
 		/*
 		 * If DMA cannot be used right now, we complete this
@@ -818,8 +813,8 @@
 	dmaengine_terminate_async(uap->dmatx.chan);
 
 	if (uap->dmatx.queued) {
-		dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
-			     DMA_TO_DEVICE);
+		dma_unmap_single(uap->dmatx.chan->device->dev, uap->dmatx.dma,
+				 uap->dmatx.len, DMA_TO_DEVICE);
 		uap->dmatx.queued = false;
 		uap->dmacr &= ~UART011_TXDMAE;
 		pl011_write(uap->dmacr, uap, REG_DMACR);
@@ -833,15 +828,15 @@
 	struct dma_chan *rxchan = uap->dmarx.chan;
 	struct pl011_dmarx_data *dmarx = &uap->dmarx;
 	struct dma_async_tx_descriptor *desc;
-	struct pl011_sgbuf *sgbuf;
+	struct pl011_dmabuf *dbuf;
 
 	if (!rxchan)
 		return -EIO;
 
 	/* Start the RX DMA job */
-	sgbuf = uap->dmarx.use_buf_b ?
-		&uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
-	desc = dmaengine_prep_slave_sg(rxchan, &sgbuf->sg, 1,
+	dbuf = uap->dmarx.use_buf_b ?
+		&uap->dmarx.dbuf_b : &uap->dmarx.dbuf_a;
+	desc = dmaengine_prep_slave_single(rxchan, dbuf->dma, dbuf->len,
 					DMA_DEV_TO_MEM,
 					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	/*
@@ -881,8 +876,8 @@
 			       bool readfifo)
 {
 	struct tty_port *port = &uap->port.state->port;
-	struct pl011_sgbuf *sgbuf = use_buf_b ?
-		&uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
+	struct pl011_dmabuf *dbuf = use_buf_b ?
+		&uap->dmarx.dbuf_b : &uap->dmarx.dbuf_a;
 	int dma_count = 0;
 	u32 fifotaken = 0; /* only used for vdbg() */
 
@@ -891,7 +886,7 @@
 
 	if (uap->dmarx.poll_rate) {
 		/* The data can be taken by polling */
-		dmataken = sgbuf->sg.length - dmarx->last_residue;
+		dmataken = dbuf->len - dmarx->last_residue;
 		/* Recalculate the pending size */
 		if (pending >= dmataken)
 			pending -= dmataken;
@@ -905,7 +900,7 @@
 		 * Note that tty_insert_flip_buf() tries to take as many chars
 		 * as it can.
 		 */
-		dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken,
+		dma_count = tty_insert_flip_string(port, dbuf->buf + dmataken,
 				pending);
 
 		uap->port.icount.rx += dma_count;
@@ -916,7 +911,7 @@
 
 	/* Reset the last_residue for Rx DMA poll */
 	if (uap->dmarx.poll_rate)
-		dmarx->last_residue = sgbuf->sg.length;
+		dmarx->last_residue = dbuf->len;
 
 	/*
 	 * Only continue with trying to read the FIFO if all DMA chars have
@@ -951,8 +946,8 @@
 {
 	struct pl011_dmarx_data *dmarx = &uap->dmarx;
 	struct dma_chan *rxchan = dmarx->chan;
-	struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
-		&dmarx->sgbuf_b : &dmarx->sgbuf_a;
+	struct pl011_dmabuf *dbuf = dmarx->use_buf_b ?
+		&dmarx->dbuf_b : &dmarx->dbuf_a;
 	size_t pending;
 	struct dma_tx_state state;
 	enum dma_status dmastat;
@@ -974,7 +969,7 @@
 	pl011_write(uap->dmacr, uap, REG_DMACR);
 	uap->dmarx.running = false;
 
-	pending = sgbuf->sg.length - state.residue;
+	pending = dbuf->len - state.residue;
 	BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
 	/* Then we terminate the transfer - we now know our residue */
 	dmaengine_terminate_all(rxchan);
@@ -1001,8 +996,8 @@
 	struct pl011_dmarx_data *dmarx = &uap->dmarx;
 	struct dma_chan *rxchan = dmarx->chan;
 	bool lastbuf = dmarx->use_buf_b;
-	struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
-		&dmarx->sgbuf_b : &dmarx->sgbuf_a;
+	struct pl011_dmabuf *dbuf = dmarx->use_buf_b ?
+		&dmarx->dbuf_b : &dmarx->dbuf_a;
 	size_t pending;
 	struct dma_tx_state state;
 	int ret;
@@ -1014,13 +1009,13 @@
 	 * routine to flush out the secondary DMA buffer while
 	 * we immediately trigger the next DMA job.
 	 */
-	spin_lock_irq(&uap->port.lock);
+	uart_port_lock_irq(&uap->port);
 	/*
 	 * Rx data can be taken by the UART interrupts during
 	 * the DMA irq handler. So we check the residue here.
 	 */
 	rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state);
-	pending = sgbuf->sg.length - state.residue;
+	pending = dbuf->len - state.residue;
 	BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
 	/* Then we terminate the transfer - we now know our residue */
 	dmaengine_terminate_all(rxchan);
@@ -1030,7 +1025,7 @@
 	ret = pl011_dma_rx_trigger_dma(uap);
 
 	pl011_dma_rx_chars(uap, pending, lastbuf, false);
-	spin_unlock_irq(&uap->port.lock);
+	uart_port_unlock_irq(&uap->port);
 	/*
 	 * Do this check after we picked the DMA chars so we don't
 	 * get some IRQ immediately from RX.
@@ -1050,6 +1045,9 @@
  */
 static inline void pl011_dma_rx_stop(struct uart_amba_port *uap)
 {
+	if (!uap->using_rx_dma)
+		return;
+
 	/* FIXME.  Just disable the DMA enable */
 	uap->dmacr &= ~UART011_RXDMAE;
 	pl011_write(uap->dmacr, uap, REG_DMACR);
@@ -1069,16 +1067,16 @@
 	unsigned long flags;
 	unsigned int dmataken = 0;
 	unsigned int size = 0;
-	struct pl011_sgbuf *sgbuf;
+	struct pl011_dmabuf *dbuf;
 	int dma_count;
 	struct dma_tx_state state;
 
-	sgbuf = dmarx->use_buf_b ? &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
+	dbuf = dmarx->use_buf_b ? &uap->dmarx.dbuf_b : &uap->dmarx.dbuf_a;
 	rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state);
 	if (likely(state.residue < dmarx->last_residue)) {
-		dmataken = sgbuf->sg.length - dmarx->last_residue;
+		dmataken = dbuf->len - dmarx->last_residue;
 		size = dmarx->last_residue - state.residue;
-		dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken,
+		dma_count = tty_insert_flip_string(port, dbuf->buf + dmataken,
 				size);
 		if (dma_count == size)
 			dmarx->last_residue =  state.residue;
@@ -1093,11 +1091,11 @@
 	if (jiffies_to_msecs(jiffies - dmarx->last_jiffies)
 			> uap->dmarx.poll_timeout) {
 
-		spin_lock_irqsave(&uap->port.lock, flags);
+		uart_port_lock_irqsave(&uap->port, &flags);
 		pl011_dma_rx_stop(uap);
 		uap->im |= UART011_RXIM;
 		pl011_write(uap->im, uap, REG_IMSC);
-		spin_unlock_irqrestore(&uap->port.lock, flags);
+		uart_port_unlock_irqrestore(&uap->port, flags);
 
 		uap->dmarx.running = false;
 		dmaengine_terminate_all(rxchan);
@@ -1125,7 +1123,7 @@
 		return;
 	}
 
-	sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE);
+	uap->dmatx.len = PL011_DMA_BUFFER_SIZE;
 
 	/* The DMA buffer is now the FIFO the TTY subsystem can use */
 	uap->port.fifosize = PL011_DMA_BUFFER_SIZE;
@@ -1135,7 +1133,7 @@
 		goto skip_rx;
 
 	/* Allocate and map DMA RX buffers */
-	ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
+	ret = pl011_dmabuf_init(uap->dmarx.chan, &uap->dmarx.dbuf_a,
 			       DMA_FROM_DEVICE);
 	if (ret) {
 		dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
@@ -1143,12 +1141,12 @@
 		goto skip_rx;
 	}
 
-	ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_b,
+	ret = pl011_dmabuf_init(uap->dmarx.chan, &uap->dmarx.dbuf_b,
 			       DMA_FROM_DEVICE);
 	if (ret) {
 		dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
 			"RX buffer B", ret);
-		pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
+		pl011_dmabuf_free(uap->dmarx.chan, &uap->dmarx.dbuf_a,
 				 DMA_FROM_DEVICE);
 		goto skip_rx;
 	}
@@ -1193,17 +1191,18 @@
 	while (pl011_read(uap, REG_FR) & uap->vendor->fr_busy)
 		cpu_relax();
 
-	spin_lock_irq(&uap->port.lock);
+	uart_port_lock_irq(&uap->port);
 	uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE);
 	pl011_write(uap->dmacr, uap, REG_DMACR);
-	spin_unlock_irq(&uap->port.lock);
+	uart_port_unlock_irq(&uap->port);
 
 	if (uap->using_tx_dma) {
 		/* In theory, this should already be done by pl011_dma_flush_buffer */
 		dmaengine_terminate_all(uap->dmatx.chan);
 		if (uap->dmatx.queued) {
-			dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
-				     DMA_TO_DEVICE);
+			dma_unmap_single(uap->dmatx.chan->device->dev,
+					 uap->dmatx.dma, uap->dmatx.len,
+					 DMA_TO_DEVICE);
 			uap->dmatx.queued = false;
 		}
 
@@ -1214,8 +1213,8 @@
 	if (uap->using_rx_dma) {
 		dmaengine_terminate_all(uap->dmarx.chan);
 		/* Clean up the RX DMA */
-		pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a, DMA_FROM_DEVICE);
-		pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_b, DMA_FROM_DEVICE);
+		pl011_dmabuf_free(uap->dmarx.chan, &uap->dmarx.dbuf_a, DMA_FROM_DEVICE);
+		pl011_dmabuf_free(uap->dmarx.chan, &uap->dmarx.dbuf_b, DMA_FROM_DEVICE);
 		if (uap->dmarx.poll_rate)
 			del_timer_sync(&uap->dmarx.timer);
 		uap->using_rx_dma = false;
@@ -1288,13 +1287,18 @@
 
 static void pl011_rs485_tx_stop(struct uart_amba_port *uap)
 {
+	/*
+	 * To be on the safe side only time out after twice as many iterations
+	 * as fifo size.
+	 */
+	const int MAX_TX_DRAIN_ITERS = uap->port.fifosize * 2;
 	struct uart_port *port = &uap->port;
 	int i = 0;
 	u32 cr;
 
 	/* Wait until hardware tx queue is empty */
 	while (!pl011_tx_empty(port)) {
-		if (i == port->fifosize) {
+		if (i > MAX_TX_DRAIN_ITERS) {
 			dev_warn(port->dev,
 				 "timeout while draining hardware tx queue\n");
 			break;
@@ -1346,11 +1350,41 @@
 	}
 }
 
+static void pl011_rs485_tx_start(struct uart_amba_port *uap)
+{
+	struct uart_port *port = &uap->port;
+	u32 cr;
+
+	/* Enable transmitter */
+	cr = pl011_read(uap, REG_CR);
+	cr |= UART011_CR_TXE;
+
+	/* Disable receiver if half-duplex */
+	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
+		cr &= ~UART011_CR_RXE;
+
+	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
+		cr &= ~UART011_CR_RTS;
+	else
+		cr |= UART011_CR_RTS;
+
+	pl011_write(cr, uap, REG_CR);
+
+	if (port->rs485.delay_rts_before_send)
+		mdelay(port->rs485.delay_rts_before_send);
+
+	uap->rs485_tx_started = true;
+}
+
 static void pl011_start_tx(struct uart_port *port)
 {
 	struct uart_amba_port *uap =
 	    container_of(port, struct uart_amba_port, port);
 
+	if ((uap->port.rs485.flags & SER_RS485_ENABLED) &&
+	    !uap->rs485_tx_started)
+		pl011_rs485_tx_start(uap);
+
 	if (!pl011_dma_tx_start(uap))
 		pl011_start_tx_pio(uap);
 }
@@ -1367,6 +1401,15 @@
 	pl011_dma_rx_stop(uap);
 }
 
+static void pl011_throttle_rx(struct uart_port *port)
+{
+	unsigned long flags;
+
+	uart_port_lock_irqsave(port, &flags);
+	pl011_stop_rx(port);
+	uart_port_unlock_irqrestore(port, flags);
+}
+
 static void pl011_enable_ms(struct uart_port *port)
 {
 	struct uart_amba_port *uap =
@@ -1382,7 +1425,7 @@
 {
 	pl011_fifo_to_tty(uap);
 
-	spin_unlock(&uap->port.lock);
+	uart_port_unlock(&uap->port);
 	tty_flip_buffer_push(&uap->port.state->port);
 	/*
 	 * If we were temporarily out of DMA mode for a while,
@@ -1407,7 +1450,7 @@
 #endif
 		}
 	}
-	spin_lock(&uap->port.lock);
+	uart_port_lock(&uap->port);
 }
 
 static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
@@ -1423,32 +1466,6 @@
 	return true;
 }
 
-static void pl011_rs485_tx_start(struct uart_amba_port *uap)
-{
-	struct uart_port *port = &uap->port;
-	u32 cr;
-
-	/* Enable transmitter */
-	cr = pl011_read(uap, REG_CR);
-	cr |= UART011_CR_TXE;
-
-	/* Disable receiver if half-duplex */
-	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
-		cr &= ~UART011_CR_RXE;
-
-	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
-		cr &= ~UART011_CR_RTS;
-	else
-		cr |= UART011_CR_RTS;
-
-	pl011_write(cr, uap, REG_CR);
-
-	if (port->rs485.delay_rts_before_send)
-		mdelay(port->rs485.delay_rts_before_send);
-
-	uap->rs485_tx_started = true;
-}
-
 /* Returns true if tx interrupts have to be (kept) enabled  */
 static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 {
@@ -1466,10 +1483,6 @@
 		return false;
 	}
 
-	if ((uap->port.rs485.flags & SER_RS485_ENABLED) &&
-	    !uap->rs485_tx_started)
-		pl011_rs485_tx_start(uap);
-
 	/* If we are using DMA mode, try to send some characters. */
 	if (pl011_dma_tx_irq(uap))
 		return true;
@@ -1543,7 +1556,7 @@
 	unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
 	int handled = 0;
 
-	spin_lock_irqsave(&uap->port.lock, flags);
+	uart_port_lock_irqsave(&uap->port, &flags);
 	status = pl011_read(uap, REG_RIS) & uap->im;
 	if (status) {
 		do {
@@ -1573,7 +1586,7 @@
 		handled = 1;
 	}
 
-	spin_unlock_irqrestore(&uap->port.lock, flags);
+	uart_port_unlock_irqrestore(&uap->port, flags);
 
 	return IRQ_RETVAL(handled);
 }
@@ -1615,9 +1628,6 @@
 	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr;
 
-	if (port->rs485.flags & SER_RS485_ENABLED)
-		mctrl &= ~TIOCM_RTS;
-
 	cr = pl011_read(uap, REG_CR);
 
 #define	TIOCMBIT(tiocmbit, uartbit)		\
@@ -1648,14 +1658,14 @@
 	unsigned long flags;
 	unsigned int lcr_h;
 
-	spin_lock_irqsave(&uap->port.lock, flags);
+	uart_port_lock_irqsave(&uap->port, &flags);
 	lcr_h = pl011_read(uap, REG_LCRH_TX);
 	if (break_state == -1)
 		lcr_h |= UART01x_LCRH_BRK;
 	else
 		lcr_h &= ~UART01x_LCRH_BRK;
 	pl011_write(lcr_h, uap, REG_LCRH_TX);
-	spin_unlock_irqrestore(&uap->port.lock, flags);
+	uart_port_unlock_irqrestore(&uap->port, flags);
 }
 
 #ifdef CONFIG_CONSOLE_POLL
@@ -1791,9 +1801,10 @@
  */
 static void pl011_enable_interrupts(struct uart_amba_port *uap)
 {
+	unsigned long flags;
 	unsigned int i;
 
-	spin_lock_irq(&uap->port.lock);
+	uart_port_lock_irqsave(&uap->port, &flags);
 
 	/* Clear out any spuriously appearing RX interrupts */
 	pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR);
@@ -1815,7 +1826,30 @@
 	if (!pl011_dma_rx_running(uap))
 		uap->im |= UART011_RXIM;
 	pl011_write(uap->im, uap, REG_IMSC);
-	spin_unlock_irq(&uap->port.lock);
+	uart_port_unlock_irqrestore(&uap->port, flags);
+}
+
+static void pl011_unthrottle_rx(struct uart_port *port)
+{
+	struct uart_amba_port *uap = container_of(port, struct uart_amba_port, port);
+	unsigned long flags;
+
+	uart_port_lock_irqsave(&uap->port, &flags);
+
+	uap->im = UART011_RTIM;
+	if (!pl011_dma_rx_running(uap))
+		uap->im |= UART011_RXIM;
+
+	pl011_write(uap->im, uap, REG_IMSC);
+
+#ifdef CONFIG_DMA_ENGINE
+	if (uap->using_rx_dma) {
+		uap->dmacr |= UART011_RXDMAE;
+		pl011_write(uap->dmacr, uap, REG_DMACR);
+	}
+#endif
+
+	uart_port_unlock_irqrestore(&uap->port, flags);
 }
 
 static int pl011_startup(struct uart_port *port)
@@ -1835,24 +1869,18 @@
 
 	pl011_write(uap->vendor->ifls, uap, REG_IFLS);
 
-	spin_lock_irq(&uap->port.lock);
+	uart_port_lock_irq(&uap->port);
 
 	/* restore RTS and DTR */
 	cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR);
 	cr |= UART01x_CR_UARTEN | UART011_CR_RXE;
 
-	if (port->rs485.flags & SER_RS485_ENABLED) {
-		if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
-			cr &= ~UART011_CR_RTS;
-		else
-			cr |= UART011_CR_RTS;
-	} else {
+	if (!(port->rs485.flags & SER_RS485_ENABLED))
 		cr |= UART011_CR_TXE;
-	}
 
 	pl011_write(cr, uap, REG_CR);
 
-	spin_unlock_irq(&uap->port.lock);
+	uart_port_unlock_irq(&uap->port);
 
 	/*
 	 * initialise the old status of the modem signals
@@ -1913,13 +1941,13 @@
 	unsigned int cr;
 
 	uap->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS);
-	spin_lock_irq(&uap->port.lock);
+	uart_port_lock_irq(&uap->port);
 	cr = pl011_read(uap, REG_CR);
 	uap->old_cr = cr;
 	cr &= UART011_CR_RTS | UART011_CR_DTR;
 	cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
 	pl011_write(cr, uap, REG_CR);
-	spin_unlock_irq(&uap->port.lock);
+	uart_port_unlock_irq(&uap->port);
 
 	/*
 	 * disable break condition and fifos
@@ -1931,14 +1959,14 @@
 
 static void pl011_disable_interrupts(struct uart_amba_port *uap)
 {
-	spin_lock_irq(&uap->port.lock);
+	uart_port_lock_irq(&uap->port);
 
 	/* mask all interrupts and clear all pending ones */
 	uap->im = 0;
 	pl011_write(uap->im, uap, REG_IMSC);
 	pl011_write(0xffff, uap, REG_ICR);
 
-	spin_unlock_irq(&uap->port.lock);
+	uart_port_unlock_irq(&uap->port);
 }
 
 static void pl011_shutdown(struct uart_port *port)
@@ -2083,7 +2111,7 @@
 
 	bits = tty_get_frame_size(termios->c_cflag);
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 
 	/*
 	 * Update the per-port timeout.
@@ -2095,7 +2123,7 @@
 	 * with the given baud rate. We use this as the poll interval when we
 	 * wait for the tx queue to empty.
 	 */
-	uap->rs485_tx_drain_interval = (bits * 1000 * 1000) / baud;
+	uap->rs485_tx_drain_interval = DIV_ROUND_UP(bits * 1000 * 1000, baud);
 
 	pl011_setup_status_masks(port, termios);
 
@@ -2105,9 +2133,7 @@
 	if (port->rs485.flags & SER_RS485_ENABLED)
 		termios->c_cflag &= ~CRTSCTS;
 
-	/* first, disable everything */
 	old_cr = pl011_read(uap, REG_CR);
-	pl011_write(0, uap, REG_CR);
 
 	if (termios->c_cflag & CRTSCTS) {
 		if (old_cr & UART011_CR_RTS)
@@ -2152,7 +2178,7 @@
 	pl011_write_lcr_h(uap, lcr_h);
 	pl011_write(old_cr, uap, REG_CR);
 
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 }
 
 static void
@@ -2170,9 +2196,58 @@
 	termios->c_cflag &= ~(CMSPAR | CRTSCTS);
 	termios->c_cflag |= CS8 | CLOCAL;
 
+	uart_port_lock_irqsave(port, &flags);
+	uart_update_timeout(port, CS8, uap->fixed_baud);
+	pl011_setup_status_masks(port, termios);
+	uart_port_unlock_irqrestore(port, flags);
+}
+
+static void
+xlnx_sbsa_uart_set_termios(struct uart_port *port, struct ktermios *termios,
+			   struct ktermios *old)
+{
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
+	unsigned long flags;
+	unsigned int lcr_h, old_cr;
+
+	tty_termios_encode_baud_rate(termios, uap->fixed_baud, uap->fixed_baud);
+	/* The SBSA UART only supports 8n1 without hardware flow control. */
+	termios->c_cflag &= ~(CMSPAR | CRTSCTS);
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		lcr_h = UART01x_LCRH_WLEN_5;
+		break;
+	case CS6:
+		lcr_h = UART01x_LCRH_WLEN_6;
+		break;
+	case CS7:
+		lcr_h = UART01x_LCRH_WLEN_7;
+		break;
+	default:
+		lcr_h = UART01x_LCRH_WLEN_8;
+		break;
+	}
+	if (termios->c_cflag & CSTOPB)
+		lcr_h |= UART01x_LCRH_STP2;
+	if (termios->c_cflag & PARENB) {
+		lcr_h |= UART01x_LCRH_PEN;
+		if (!(termios->c_cflag & PARODD))
+			lcr_h |= UART01x_LCRH_EPS;
+		if (termios->c_cflag & CMSPAR)
+			lcr_h |= UART011_LCRH_SPS;
+	}
+	if (uap->fifosize > 1)
+		lcr_h |= UART01x_LCRH_FEN;
+
 	spin_lock_irqsave(&port->lock, flags);
 	uart_update_timeout(port, CS8, uap->fixed_baud);
 	pl011_setup_status_masks(port, termios);
+	/* first, disable everything */
+	old_cr = pl011_read(uap, REG_CR);
+	pl011_write(0, uap, REG_CR);
+	pl011_write_lcr_h(uap, lcr_h);
+	pl011_write(old_cr, uap, REG_CR);
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
@@ -2205,10 +2280,8 @@
  */
 static void pl011_config_port(struct uart_port *port, int flags)
 {
-	if (flags & UART_CONFIG_TYPE) {
+	if (flags & UART_CONFIG_TYPE)
 		port->type = PORT_AMBA;
-		pl011_request_port(port);
-	}
 }
 
 /*
@@ -2223,10 +2296,12 @@
 		ret = -EINVAL;
 	if (ser->baud_base < 9600)
 		ret = -EINVAL;
+	if (port->mapbase != (unsigned long) ser->iomem_base)
+		ret = -EINVAL;
 	return ret;
 }
 
-static int pl011_rs485_config(struct uart_port *port,
+static int pl011_rs485_config(struct uart_port *port, struct ktermios *termios,
 			      struct serial_rs485 *rs485)
 {
 	struct uart_amba_port *uap =
@@ -2268,6 +2343,8 @@
 	.stop_tx	= pl011_stop_tx,
 	.start_tx	= pl011_start_tx,
 	.stop_rx	= pl011_stop_rx,
+	.throttle	= pl011_throttle_rx,
+	.unthrottle	= pl011_unthrottle_rx,
 	.enable_ms	= pl011_enable_ms,
 	.break_ctl	= pl011_break_ctl,
 	.startup	= pl011_startup,
@@ -2275,8 +2352,6 @@
 	.flush_buffer	= pl011_dma_flush_buffer,
 	.set_termios	= pl011_set_termios,
 	.type		= pl011_type,
-	.release_port	= pl011_release_port,
-	.request_port	= pl011_request_port,
 	.config_port	= pl011_config_port,
 	.verify_port	= pl011_verify_port,
 #ifdef CONFIG_CONSOLE_POLL
@@ -2306,6 +2381,26 @@
 	.shutdown	= sbsa_uart_shutdown,
 	.set_termios	= sbsa_uart_set_termios,
 	.type		= pl011_type,
+	.config_port	= pl011_config_port,
+	.verify_port	= pl011_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_init     = pl011_hwinit,
+	.poll_get_char = pl011_get_poll_char,
+	.poll_put_char = pl011_put_poll_char,
+#endif
+};
+
+static const struct uart_ops xlnx_sbsa_uart_pops = {
+	.tx_empty	= pl011_tx_empty,
+	.set_mctrl	= sbsa_uart_set_mctrl,
+	.get_mctrl	= sbsa_uart_get_mctrl,
+	.stop_tx	= pl011_stop_tx,
+	.start_tx	= pl011_start_tx,
+	.stop_rx	= pl011_stop_rx,
+	.startup	= sbsa_uart_startup,
+	.shutdown	= sbsa_uart_shutdown,
+	.set_termios	= xlnx_sbsa_uart_set_termios,
+	.type		= pl011_type,
 	.release_port	= pl011_release_port,
 	.request_port	= pl011_request_port,
 	.config_port	= pl011_config_port,
@@ -2345,9 +2440,9 @@
 	if (uap->port.sysrq)
 		locked = 0;
 	else if (oops_in_progress)
-		locked = spin_trylock(&uap->port.lock);
+		locked = uart_port_trylock(&uap->port);
 	else
-		spin_lock(&uap->port.lock);
+		uart_port_lock(&uap->port);
 
 	/*
 	 *	First save the CR then disable the interrupts
@@ -2373,7 +2468,7 @@
 		pl011_write(old_cr, uap, REG_CR);
 
 	if (locked)
-		spin_unlock(&uap->port.lock);
+		uart_port_unlock(&uap->port);
 	local_irq_restore(flags);
 
 	clk_disable(uap->clk);
@@ -2914,7 +3009,10 @@
 	uap->reg_offset	= uap->vendor->reg_offset;
 	uap->fifosize	= 32;
 	uap->port.iotype = uap->vendor->access_32b ? UPIO_MEM32 : UPIO_MEM;
-	uap->port.ops	= &sbsa_uart_pops;
+	if (of_device_is_compatible(pdev->dev.of_node, "arm,xlnx-sbsa-uart"))
+		uap->port.ops	= &xlnx_sbsa_uart_pops;
+	else
+		uap->port.ops	= &sbsa_uart_pops;
 	uap->fixed_baud = baudrate;
 
 	snprintf(uap->type, sizeof(uap->type), "SBSA");
@@ -2941,12 +3039,14 @@
 
 static const struct of_device_id sbsa_uart_of_match[] = {
 	{ .compatible = "arm,sbsa-uart", },
+	{ .compatible = "arm,xlnx-sbsa-uart", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, sbsa_uart_of_match);
 
 static const struct acpi_device_id __maybe_unused sbsa_uart_acpi_match[] = {
 	{ "ARMH0011", 0 },
+	{ "ARMHB000", 0 },
 	{},
 };
 MODULE_DEVICE_TABLE(acpi, sbsa_uart_acpi_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/ar933x_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/ar933x_uart.c
@@ -580,7 +580,7 @@
 	.verify_port	= ar933x_uart_verify_port,
 };
 
-static int ar933x_config_rs485(struct uart_port *port,
+static int ar933x_config_rs485(struct uart_port *port, struct ktermios *termios,
 				struct serial_rs485 *rs485conf)
 {
 	struct ar933x_uart_port *up =
@@ -591,6 +591,11 @@
 		dev_err(port->dev, "RS485 needs rts-gpio\n");
 		return 1;
 	}
+
+	if (rs485conf->flags & SER_RS485_ENABLED)
+		gpiod_set_value(up->rts_gpiod,
+			!!(rs485conf->flags & SER_RS485_RTS_AFTER_SEND));
+
 	port->rs485 = *rs485conf;
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/arc_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/arc_uart.c
@@ -607,10 +607,11 @@
 	}
 	uart->baud = val;
 
-	port->membase = of_iomap(np, 0);
-	if (!port->membase)
+	port->membase = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(port->membase)) {
 		/* No point of dev_err since UART itself is hosed here */
-		return -ENXIO;
+		return PTR_ERR(port->membase);
+	}
 
 	port->irq = irq_of_parse_and_map(np, 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/atmel_serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/atmel_serial.c
@@ -284,7 +284,7 @@
 }
 
 /* Enable or disable the rs485 support */
-static int atmel_config_rs485(struct uart_port *port,
+static int atmel_config_rs485(struct uart_port *port, struct ktermios *termios,
 			      struct serial_rs485 *rs485conf)
 {
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
@@ -295,20 +295,16 @@
 
 	mode = atmel_uart_readl(port, ATMEL_US_MR);
 
-	/* Resetting serial mode to RS232 (0x0) */
-	mode &= ~ATMEL_US_USMODE;
-
-	port->rs485 = *rs485conf;
-
 	if (rs485conf->flags & SER_RS485_ENABLED) {
 		dev_dbg(port->dev, "Setting UART to RS485\n");
-		if (port->rs485.flags & SER_RS485_RX_DURING_TX)
+		if (rs485conf->flags & SER_RS485_RX_DURING_TX)
 			atmel_port->tx_done_mask = ATMEL_US_TXRDY;
 		else
 			atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
 
 		atmel_uart_writel(port, ATMEL_US_TTGR,
 				  rs485conf->delay_rts_after_send);
+		mode &= ~ATMEL_US_USMODE;
 		mode |= ATMEL_US_USMODE_RS485;
 	} else {
 		dev_dbg(port->dev, "Setting UART to RS232\n");
@@ -877,11 +873,11 @@
 
 	port->icount.tx += atmel_port->tx_len;
 
-	spin_lock_irq(&atmel_port->lock_tx);
+	spin_lock(&atmel_port->lock_tx);
 	async_tx_ack(atmel_port->desc_tx);
 	atmel_port->cookie_tx = -EINVAL;
 	atmel_port->desc_tx = NULL;
-	spin_unlock_irq(&atmel_port->lock_tx);
+	spin_unlock(&atmel_port->lock_tx);
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(port);
@@ -1004,6 +1000,13 @@
 		desc->callback = atmel_complete_tx_dma;
 		desc->callback_param = atmel_port;
 		atmel_port->cookie_tx = dmaengine_submit(desc);
+		if (dma_submit_error(atmel_port->cookie_tx)) {
+			dev_err(port->dev, "dma_submit_error %d\n",
+				atmel_port->cookie_tx);
+			return;
+		}
+
+		dma_async_issue_pending(chan);
 	}
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
@@ -1258,6 +1261,13 @@
 	desc->callback_param = port;
 	atmel_port->desc_rx = desc;
 	atmel_port->cookie_rx = dmaengine_submit(desc);
+	if (dma_submit_error(atmel_port->cookie_rx)) {
+		dev_err(port->dev, "dma_submit_error %d\n",
+			atmel_port->cookie_rx);
+		goto chan_err;
+	}
+
+	dma_async_issue_pending(atmel_port->chan_rx);
 
 	return 0;
 
@@ -2605,13 +2615,7 @@
 	else if (mr == ATMEL_US_PAR_ODD)
 		*parity = 'o';
 
-	/*
-	 * The serial core only rounds down when matching this to a
-	 * supported baud rate. Make sure we don't end up slightly
-	 * lower than one of those, as it would make us fall through
-	 * to a much lower baud rate than we really want.
-	 */
-	*baud = port->uartclk / (16 * (quot - 1));
+	*baud = port->uartclk / (16 * quot);
 }
 
 static int __init atmel_console_setup(struct console *co, char *options)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/cpm_uart/cpm_uart_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/cpm_uart/cpm_uart_core.c
@@ -1090,6 +1090,7 @@
 	cpm_uart_early_write(pinfo, ch, 1, false);
 }
 
+#ifdef CONFIG_SERIAL_CPM_CONSOLE
 static struct uart_port *udbg_port;
 
 static void udbg_cpm_putc(char c)
@@ -1114,6 +1115,7 @@
 		cpu_relax();
 	return c;
 }
+#endif /* CONFIG_SERIAL_CPM_CONSOLE */
 
 #endif /* CONFIG_CONSOLE_POLL */
 
@@ -1245,7 +1247,7 @@
 	}
 
 #ifdef CONFIG_PPC_EARLY_DEBUG_CPM
-#ifdef CONFIG_CONSOLE_POLL
+#if defined(CONFIG_CONSOLE_POLL) && defined(CONFIG_SERIAL_CPM_CONSOLE)
 	if (!udbg_port)
 #endif
 		udbg_putc = NULL;
@@ -1274,19 +1276,14 @@
 {
 	struct uart_cpm_port *pinfo = &cpm_uart_ports[co->index];
 	unsigned long flags;
-	int nolock = oops_in_progress;
 
-	if (unlikely(nolock)) {
+	if (unlikely(oops_in_progress)) {
 		local_irq_save(flags);
-	} else {
-		spin_lock_irqsave(&pinfo->port.lock, flags);
-	}
-
-	cpm_uart_early_write(pinfo, s, count, true);
-
-	if (unlikely(nolock)) {
+		cpm_uart_early_write(pinfo, s, count, true);
 		local_irq_restore(flags);
 	} else {
+		spin_lock_irqsave(&pinfo->port.lock, flags);
+		cpm_uart_early_write(pinfo, s, count, true);
 		spin_unlock_irqrestore(&pinfo->port.lock, flags);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/digicolor-usart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/digicolor-usart.c
@@ -309,6 +309,8 @@
 	case CS8:
 	default:
 		config |= UA_CONFIG_CHAR_LEN;
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
 		break;
 	}
 
@@ -471,11 +473,10 @@
 	if (IS_ERR(uart_clk))
 		return PTR_ERR(uart_clk);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	dp->port.mapbase = res->start;
-	dp->port.membase = devm_ioremap_resource(&pdev->dev, res);
+	dp->port.membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 	if (IS_ERR(dp->port.membase))
 		return PTR_ERR(dp->port.membase);
+	dp->port.mapbase = res->start;
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/fsl_lpuart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/fsl_lpuart.c
@@ -12,6 +12,7 @@
 #include <linux/dmaengine.h>
 #include <linux/dmapool.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/irq.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -239,14 +240,13 @@
 /* IMX lpuart has four extra unused regs located at the beginning */
 #define IMX_REG_OFF	0x10
 
-static DEFINE_IDA(fsl_lpuart_ida);
-
 enum lpuart_type {
 	VF610_LPUART,
 	LS1021A_LPUART,
 	LS1028A_LPUART,
 	IMX7ULP_LPUART,
 	IMX8QXP_LPUART,
+	IMXRT1050_LPUART,
 };
 
 struct lpuart_port {
@@ -257,6 +257,7 @@
 	unsigned int		txfifo_size;
 	unsigned int		rxfifo_size;
 
+	u8			rx_watermark;
 	bool			lpuart_dma_tx_use;
 	bool			lpuart_dma_rx_use;
 	struct dma_chan		*dma_tx_chan;
@@ -275,40 +276,51 @@
 	int			rx_dma_rng_buf_len;
 	unsigned int		dma_tx_nents;
 	wait_queue_head_t	dma_wait;
-	bool			id_allocated;
 };
 
 struct lpuart_soc_data {
 	enum lpuart_type devtype;
 	char iotype;
 	u8 reg_off;
+	u8 rx_watermark;
 };
 
 static const struct lpuart_soc_data vf_data = {
 	.devtype = VF610_LPUART,
 	.iotype = UPIO_MEM,
+	.rx_watermark = 1,
 };
 
 static const struct lpuart_soc_data ls1021a_data = {
 	.devtype = LS1021A_LPUART,
 	.iotype = UPIO_MEM32BE,
+	.rx_watermark = 1,
 };
 
 static const struct lpuart_soc_data ls1028a_data = {
 	.devtype = LS1028A_LPUART,
 	.iotype = UPIO_MEM32,
+	.rx_watermark = 0,
 };
 
 static struct lpuart_soc_data imx7ulp_data = {
 	.devtype = IMX7ULP_LPUART,
 	.iotype = UPIO_MEM32,
 	.reg_off = IMX_REG_OFF,
+	.rx_watermark = 1,
 };
 
 static struct lpuart_soc_data imx8qxp_data = {
 	.devtype = IMX8QXP_LPUART,
 	.iotype = UPIO_MEM32,
 	.reg_off = IMX_REG_OFF,
+	.rx_watermark = 1,
+};
+static struct lpuart_soc_data imxrt1050_data = {
+	.devtype = IMXRT1050_LPUART,
+	.iotype = UPIO_MEM32,
+	.reg_off = IMX_REG_OFF,
+	.rx_watermark = 1,
 };
 
 static const struct of_device_id lpuart_dt_ids[] = {
@@ -317,6 +329,7 @@
 	{ .compatible = "fsl,ls1028a-lpuart",	.data = &ls1028a_data, },
 	{ .compatible = "fsl,imx7ulp-lpuart",	.data = &imx7ulp_data, },
 	{ .compatible = "fsl,imx8qxp-lpuart",	.data = &imx8qxp_data, },
+	{ .compatible = "fsl,imxrt1050-lpuart",	.data = &imxrt1050_data},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, lpuart_dt_ids);
@@ -398,33 +411,6 @@
 #define lpuart_enable_clks(x)	__lpuart_enable_clks(x, true)
 #define lpuart_disable_clks(x)	__lpuart_enable_clks(x, false)
 
-static int lpuart_global_reset(struct lpuart_port *sport)
-{
-	struct uart_port *port = &sport->port;
-	void __iomem *global_addr;
-	int ret;
-
-	if (uart_console(port))
-		return 0;
-
-	ret = clk_prepare_enable(sport->ipg_clk);
-	if (ret) {
-		dev_err(sport->port.dev, "failed to enable uart ipg clk: %d\n", ret);
-		return ret;
-	}
-
-	if (is_imx7ulp_lpuart(sport) || is_imx8qxp_lpuart(sport)) {
-		global_addr = port->membase + UART_GLOBAL - IMX_REG_OFF;
-		writel(UART_GLOBAL_RST, global_addr);
-		usleep_range(GLOBAL_RST_MIN_US, GLOBAL_RST_MAX_US);
-		writel(0, global_addr);
-		usleep_range(GLOBAL_RST_MIN_US, GLOBAL_RST_MAX_US);
-	}
-
-	clk_disable_unprepare(sport->ipg_clk);
-	return 0;
-}
-
 static void lpuart_stop_tx(struct uart_port *port)
 {
 	unsigned char temp;
@@ -602,7 +588,7 @@
 				sport->dma_tx_nents, DMA_TO_DEVICE);
 			sport->dma_tx_in_progress = false;
 		}
-		dmaengine_terminate_all(chan);
+		dmaengine_terminate_async(chan);
 	}
 
 	if (lpuart_is_32(sport)) {
@@ -858,11 +844,17 @@
 			struct lpuart_port, port);
 	unsigned long stat = lpuart32_read(port, UARTSTAT);
 	unsigned long sfifo = lpuart32_read(port, UARTFIFO);
+	unsigned long ctrl = lpuart32_read(port, UARTCTRL);
 
 	if (sport->dma_tx_in_progress)
 		return 0;
 
-	if (stat & UARTSTAT_TC && sfifo & UARTFIFO_TXEMPT)
+	/*
+	 * LPUART Transmission Complete Flag may never be set while queuing a break
+	 * character, so avoid checking for transmission complete when UARTCTRL_SBK
+	 * is asserted.
+	 */
+	if ((stat & UARTSTAT_TC && sfifo & UARTFIFO_TXEMPT) || ctrl & UARTCTRL_SBK)
 		return TIOCSER_TEMT;
 
 	return 0;
@@ -985,12 +977,12 @@
 
 		if (sr & (UARTSTAT_PE | UARTSTAT_OR | UARTSTAT_FE)) {
 			if (sr & UARTSTAT_PE) {
+				sport->port.icount.parity++;
+			} else if (sr & UARTSTAT_FE) {
 				if (is_break)
 					sport->port.icount.brk++;
 				else
-					sport->port.icount.parity++;
-			} else if (sr & UARTSTAT_FE) {
-				sport->port.icount.frame++;
+					sport->port.icount.frame++;
 			}
 
 			if (sr & UARTSTAT_OR)
@@ -1005,12 +997,12 @@
 			sr &= sport->port.read_status_mask;
 
 			if (sr & UARTSTAT_PE) {
+				flg = TTY_PARITY;
+			} else if (sr & UARTSTAT_FE) {
 				if (is_break)
 					flg = TTY_BREAK;
 				else
-					flg = TTY_PARITY;
-			} else if (sr & UARTSTAT_FE) {
-				flg = TTY_FRAME;
+					flg = TTY_FRAME;
 			}
 
 			if (sr & UARTSTAT_OR)
@@ -1115,8 +1107,8 @@
 		unsigned long sr = lpuart32_read(&sport->port, UARTSTAT);
 
 		if (sr & (UARTSTAT_PE | UARTSTAT_FE)) {
-			/* Read DR to clear the error flags */
-			lpuart32_read(&sport->port, UARTDATA);
+			/* Clear the error flags */
+			lpuart32_write(&sport->port, sr, UARTSTAT);
 
 			if (sr & UARTSTAT_PE)
 				sport->port.icount.parity++;
@@ -1273,7 +1265,7 @@
 	 * 10ms at any baud rate.
 	 */
 	sport->rx_dma_rng_buf_len = (DMA_RX_TIMEOUT * baud /  bits / 1000) * 2;
-	sport->rx_dma_rng_buf_len = (1 << (fls(sport->rx_dma_rng_buf_len) - 1));
+	sport->rx_dma_rng_buf_len = (1 << fls(sport->rx_dma_rng_buf_len));
 	if (sport->rx_dma_rng_buf_len < 16)
 		sport->rx_dma_rng_buf_len = 16;
 
@@ -1336,7 +1328,8 @@
 					struct lpuart_port, port);
 	struct dma_chan *chan = sport->dma_rx_chan;
 
-	dmaengine_terminate_all(chan);
+	dmaengine_terminate_sync(chan);
+	del_timer_sync(&sport->lpuart_timer);
 	dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
 	kfree(sport->rx_ring.buf);
 	sport->rx_ring.tail = 0;
@@ -1345,7 +1338,7 @@
 	sport->dma_rx_cookie = -EINVAL;
 }
 
-static int lpuart_config_rs485(struct uart_port *port,
+static int lpuart_config_rs485(struct uart_port *port, struct ktermios *termios,
 			struct serial_rs485 *rs485)
 {
 	struct lpuart_port *sport = container_of(port,
@@ -1384,9 +1377,9 @@
 		 * Note: UART is assumed to be active high.
 		 */
 		if (rs485->flags & SER_RS485_RTS_ON_SEND)
-			modem &= ~UARTMODEM_TXRTSPOL;
-		else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
 			modem |= UARTMODEM_TXRTSPOL;
+		else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
+			modem &= ~UARTMODEM_TXRTSPOL;
 	}
 
 	/* Store the new configuration */
@@ -1396,14 +1389,27 @@
 	return 0;
 }
 
-static int lpuart32_config_rs485(struct uart_port *port,
+static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termios,
 			struct serial_rs485 *rs485)
 {
 	struct lpuart_port *sport = container_of(port,
 			struct lpuart_port, port);
 
 	unsigned long modem = lpuart32_read(&sport->port, UARTMODIR)
-				& ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
+				& ~(UARTMODIR_TXRTSPOL | UARTMODIR_TXRTSE);
+	u32 ctrl;
+
+	/* TXRTSE and TXRTSPOL only can be changed when transmitter is disabled. */
+	ctrl = lpuart32_read(&sport->port, UARTCTRL);
+	if (ctrl & UARTCTRL_TE) {
+		/* wait for the transmit engine to complete */
+		lpuart32_wait_bit_set(&sport->port, UARTSTAT, UARTSTAT_TC);
+		lpuart32_write(&sport->port, ctrl & ~UARTCTRL_TE, UARTCTRL);
+
+		while (lpuart32_read(&sport->port, UARTCTRL) & UARTCTRL_TE)
+			cpu_relax();
+	}
+
 	lpuart32_write(&sport->port, modem, UARTMODIR);
 
 	/* clear unsupported configurations */
@@ -1413,7 +1419,7 @@
 
 	if (rs485->flags & SER_RS485_ENABLED) {
 		/* Enable auto RS-485 RTS mode */
-		modem |= UARTMODEM_TXRTSE;
+		modem |= UARTMODIR_TXRTSE;
 
 		/*
 		 * RTS needs to be logic HIGH either during transfer _or_ after
@@ -1435,15 +1441,19 @@
 		 * Note: UART is assumed to be active high.
 		 */
 		if (rs485->flags & SER_RS485_RTS_ON_SEND)
-			modem &= ~UARTMODEM_TXRTSPOL;
+			modem |= UARTMODIR_TXRTSPOL;
 		else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
-			modem |= UARTMODEM_TXRTSPOL;
+			modem &= ~UARTMODIR_TXRTSPOL;
 	}
 
 	/* Store the new configuration */
 	sport->port.rs485 = *rs485;
 
 	lpuart32_write(&sport->port, modem, UARTMODIR);
+
+	if (ctrl & UARTCTRL_TE)
+		lpuart32_write(&sport->port, ctrl, UARTCTRL);
+
 	return 0;
 }
 
@@ -1515,12 +1525,34 @@
 {
 	unsigned long temp;
 
-	temp = lpuart32_read(port, UARTCTRL) & ~UARTCTRL_SBK;
-
-	if (break_state != 0)
-		temp |= UARTCTRL_SBK;
+	temp = lpuart32_read(port, UARTCTRL);
 
-	lpuart32_write(port, temp, UARTCTRL);
+	/*
+	 * LPUART IP now has two known bugs, one is CTS has higher priority than the
+	 * break signal, which causes the break signal sending through UARTCTRL_SBK
+	 * may impacted by the CTS input if the HW flow control is enabled. It
+	 * exists on all platforms we support in this driver.
+	 * Another bug is i.MX8QM LPUART may have an additional break character
+	 * being sent after SBK was cleared.
+	 * To avoid above two bugs, we use Transmit Data Inversion function to send
+	 * the break signal instead of UARTCTRL_SBK.
+	 */
+	if (break_state != 0) {
+		/*
+		 * Disable the transmitter to prevent any data from being sent out
+		 * during break, then invert the TX line to send break.
+		 */
+		temp &= ~UARTCTRL_TE;
+		lpuart32_write(port, temp, UARTCTRL);
+		temp |= UARTCTRL_TXINV;
+		lpuart32_write(port, temp, UARTCTRL);
+	} else {
+		/* Disable the TXINV to turn off break and re-enable transmitter. */
+		temp &= ~UARTCTRL_TXINV;
+		lpuart32_write(port, temp, UARTCTRL);
+		temp |= UARTCTRL_TE;
+		lpuart32_write(port, temp, UARTCTRL);
+	}
 }
 
 static void lpuart_setup_watermark(struct lpuart_port *sport)
@@ -1549,7 +1581,7 @@
 	}
 
 	writeb(0, sport->port.membase + UARTTWFIFO);
-	writeb(1, sport->port.membase + UARTRWFIFO);
+	writeb(sport->rx_watermark, sport->port.membase + UARTRWFIFO);
 
 	/* Restore cr2 */
 	writeb(cr2_saved, sport->port.membase + UARTCR2);
@@ -1584,7 +1616,8 @@
 	lpuart32_write(&sport->port, val, UARTFIFO);
 
 	/* set the watermark */
-	val = (0x1 << UARTWATER_RXWATER_OFF) | (0x0 << UARTWATER_TXWATER_OFF);
+	val = (sport->rx_watermark << UARTWATER_RXWATER_OFF) |
+	      (0x0 << UARTWATER_TXWATER_OFF);
 	lpuart32_write(&sport->port, val, UARTWATER);
 
 	/* Restore cr2 */
@@ -1729,12 +1762,6 @@
 {
 	unsigned long temp;
 
-	if (sport->lpuart_dma_rx_use) {
-		/* RXWATER must be 0 */
-		temp = lpuart32_read(&sport->port, UARTWATER);
-		temp &= ~(UARTWATER_WATER_MASK << UARTWATER_RXWATER_OFF);
-		lpuart32_write(&sport->port, temp, UARTWATER);
-	}
 	temp = lpuart32_read(&sport->port, UARTCTRL);
 	if (!sport->lpuart_dma_rx_use)
 		temp |= UARTCTRL_RIE;
@@ -1788,16 +1815,17 @@
 static void lpuart_dma_shutdown(struct lpuart_port *sport)
 {
 	if (sport->lpuart_dma_rx_use) {
-		del_timer_sync(&sport->lpuart_timer);
 		lpuart_dma_rx_free(&sport->port);
+		sport->lpuart_dma_rx_use = false;
 	}
 
 	if (sport->lpuart_dma_tx_use) {
 		if (wait_event_interruptible(sport->dma_wait,
 			!sport->dma_tx_in_progress) != false) {
 			sport->dma_tx_in_progress = false;
-			dmaengine_terminate_all(sport->dma_tx_chan);
+			dmaengine_terminate_sync(sport->dma_tx_chan);
 		}
+		sport->lpuart_dma_tx_use = false;
 	}
 
 	if (sport->dma_tx_chan)
@@ -1834,6 +1862,15 @@
 
 	spin_lock_irqsave(&port->lock, flags);
 
+	/* clear status */
+	temp = lpuart32_read(&sport->port, UARTSTAT);
+	lpuart32_write(&sport->port, temp, UARTSTAT);
+
+	/* disable Rx/Tx DMA */
+	temp = lpuart32_read(port, UARTBAUD);
+	temp &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE);
+	lpuart32_write(port, temp, UARTBAUD);
+
 	/* disable Rx/Tx and interrupts */
 	temp = lpuart32_read(port, UARTCTRL);
 	temp &= ~(UARTCTRL_TE | UARTCTRL_RE |
@@ -1937,10 +1974,8 @@
 	 * Since timer function acqures sport->port.lock, need to stop before
 	 * acquring same lock because otherwise del_timer_sync() can deadlock.
 	 */
-	if (old && sport->lpuart_dma_rx_use) {
-		del_timer_sync(&sport->lpuart_timer);
+	if (old && sport->lpuart_dma_rx_use)
 		lpuart_dma_rx_free(&sport->port);
-	}
 
 	spin_lock_irqsave(&sport->port.lock, flags);
 
@@ -2175,10 +2210,8 @@
 	 * Since timer function acqures sport->port.lock, need to stop before
 	 * acquring same lock because otherwise del_timer_sync() can deadlock.
 	 */
-	if (old && sport->lpuart_dma_rx_use) {
-		del_timer_sync(&sport->lpuart_timer);
+	if (old && sport->lpuart_dma_rx_use)
 		lpuart_dma_rx_free(&sport->port);
-	}
 
 	spin_lock_irqsave(&sport->port.lock, flags);
 
@@ -2205,8 +2238,15 @@
 	/* update the per-port timeout */
 	uart_update_timeout(port, termios->c_cflag, baud);
 
-	/* wait transmit engin complete */
-	lpuart32_wait_bit_set(&sport->port, UARTSTAT, UARTSTAT_TC);
+	/*
+	 * LPUART Transmission Complete Flag may never be set while queuing a break
+	 * character, so skip waiting for transmission complete when UARTCTRL_SBK is
+	 * asserted.
+	 */
+	if (!(old_ctrl & UARTCTRL_SBK)) {
+		lpuart32_write(&sport->port, 0, UARTMODIR);
+		lpuart32_wait_bit_set(&sport->port, UARTSTAT, UARTSTAT_TC);
+	}
 
 	/* disable transmit and receive */
 	lpuart32_write(&sport->port, old_ctrl & ~(UARTCTRL_TE | UARTCTRL_RE),
@@ -2214,9 +2254,12 @@
 
 	lpuart32_write(&sport->port, bd, UARTBAUD);
 	lpuart32_serial_setbrg(sport, baud);
-	lpuart32_write(&sport->port, modem, UARTMODIR);
-	lpuart32_write(&sport->port, ctrl, UARTCTRL);
+	/* disable CTS before enabling UARTCTRL_TE to avoid pending idle preamble */
+	lpuart32_write(&sport->port, modem & ~UARTMODIR_TXCTSE, UARTMODIR);
 	/* restore control register */
+	lpuart32_write(&sport->port, ctrl, UARTCTRL);
+	/* re-enable the CTS if needed */
+	lpuart32_write(&sport->port, modem, UARTMODIR);
 
 	if (old && sport->lpuart_dma_rx_use) {
 		if (!lpuart_start_rx_dma(sport))
@@ -2625,6 +2668,9 @@
 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1028a-lpuart", ls1028a_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
+OF_EARLYCON_DECLARE(lpuart32, "fsl,imx8ulp-lpuart", lpuart32_imx_early_console_setup);
+OF_EARLYCON_DECLARE(lpuart32, "fsl,imx8qxp-lpuart", lpuart32_imx_early_console_setup);
+OF_EARLYCON_DECLARE(lpuart32, "fsl,imxrt1050-lpuart", lpuart32_imx_early_console_setup);
 EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
 EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
 
@@ -2643,12 +2689,66 @@
 	.cons		= LPUART_CONSOLE,
 };
 
+static const struct serial_rs485 lpuart_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
+	/* delay_rts_* and RX_DURING_TX are not supported */
+};
+
+static int lpuart_global_reset(struct lpuart_port *sport)
+{
+	struct uart_port *port = &sport->port;
+	void __iomem *global_addr;
+	unsigned long ctrl, bd;
+	unsigned int val = 0;
+	int ret;
+
+	ret = clk_prepare_enable(sport->ipg_clk);
+	if (ret) {
+		dev_err(sport->port.dev, "failed to enable uart ipg clk: %d\n", ret);
+		return ret;
+	}
+
+	if (is_imx7ulp_lpuart(sport) || is_imx8qxp_lpuart(sport)) {
+		/*
+		 * If the transmitter is used by earlycon, wait for transmit engine to
+		 * complete and then reset.
+		 */
+		ctrl = lpuart32_read(port, UARTCTRL);
+		if (ctrl & UARTCTRL_TE) {
+			bd = lpuart32_read(&sport->port, UARTBAUD);
+			if (read_poll_timeout(lpuart32_tx_empty, val, val, 1, 100000, false,
+					      port)) {
+				dev_warn(sport->port.dev,
+					 "timeout waiting for transmit engine to complete\n");
+				clk_disable_unprepare(sport->ipg_clk);
+				return 0;
+			}
+		}
+
+		global_addr = port->membase + UART_GLOBAL - IMX_REG_OFF;
+		writel(UART_GLOBAL_RST, global_addr);
+		usleep_range(GLOBAL_RST_MIN_US, GLOBAL_RST_MAX_US);
+		writel(0, global_addr);
+		usleep_range(GLOBAL_RST_MIN_US, GLOBAL_RST_MAX_US);
+
+		/* Recover the transmitter for earlycon. */
+		if (ctrl & UARTCTRL_TE) {
+			lpuart32_write(port, bd, UARTBAUD);
+			lpuart32_write(port, ctrl, UARTCTRL);
+		}
+	}
+
+	clk_disable_unprepare(sport->ipg_clk);
+	return 0;
+}
+
 static int lpuart_probe(struct platform_device *pdev)
 {
 	const struct lpuart_soc_data *sdata = of_device_get_match_data(&pdev->dev);
 	struct device_node *np = pdev->dev.of_node;
 	struct lpuart_port *sport;
 	struct resource *res;
+	irq_handler_t handler;
 	int ret;
 
 	sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
@@ -2665,6 +2765,7 @@
 	sport->port.dev = &pdev->dev;
 	sport->port.type = PORT_LPUART;
 	sport->devtype = sdata->devtype;
+	sport->rx_watermark = sdata->rx_watermark;
 	ret = platform_get_irq(pdev, 0);
 	if (ret < 0)
 		return ret;
@@ -2681,6 +2782,7 @@
 		sport->port.rs485_config = lpuart32_config_rs485;
 	else
 		sport->port.rs485_config = lpuart_config_rs485;
+	sport->port.rs485_supported = &lpuart_rs485_supported;
 
 	sport->ipg_clk = devm_clk_get(&pdev->dev, "ipg");
 	if (IS_ERR(sport->ipg_clk)) {
@@ -2701,23 +2803,18 @@
 
 	ret = of_alias_get_id(np, "serial");
 	if (ret < 0) {
-		ret = ida_simple_get(&fsl_lpuart_ida, 0, UART_NR, GFP_KERNEL);
-		if (ret < 0) {
-			dev_err(&pdev->dev, "port line is full, add device failed\n");
-			return ret;
-		}
-		sport->id_allocated = true;
+		dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+		return ret;
 	}
 	if (ret >= ARRAY_SIZE(lpuart_ports)) {
 		dev_err(&pdev->dev, "serial%d out of range\n", ret);
-		ret = -EINVAL;
-		goto failed_out_of_range;
+		return -EINVAL;
 	}
 	sport->port.line = ret;
 
 	ret = lpuart_enable_clks(sport);
 	if (ret)
-		goto failed_clock_enable;
+		return ret;
 	sport->port.uartclk = lpuart_get_baud_clk_rate(sport);
 
 	lpuart_ports[sport->port.line] = sport;
@@ -2726,21 +2823,12 @@
 
 	if (lpuart_is_32(sport)) {
 		lpuart_reg.cons = LPUART32_CONSOLE;
-		ret = devm_request_irq(&pdev->dev, sport->port.irq, lpuart32_int, 0,
-					DRIVER_NAME, sport);
+		handler = lpuart32_int;
 	} else {
 		lpuart_reg.cons = LPUART_CONSOLE;
-		ret = devm_request_irq(&pdev->dev, sport->port.irq, lpuart_int, 0,
-					DRIVER_NAME, sport);
+		handler = lpuart_int;
 	}
 
-	if (ret)
-		goto failed_irq_request;
-
-	ret = uart_add_one_port(&lpuart_reg, &sport->port);
-	if (ret)
-		goto failed_attach_port;
-
 	ret = lpuart_global_reset(sport);
 	if (ret)
 		goto failed_reset;
@@ -2756,20 +2844,23 @@
 	    sport->port.rs485.delay_rts_after_send)
 		dev_err(&pdev->dev, "driver doesn't support RTS delays\n");
 
-	sport->port.rs485_config(&sport->port, &sport->port.rs485);
+	ret = uart_add_one_port(&lpuart_reg, &sport->port);
+	if (ret)
+		goto failed_attach_port;
+
+	ret = devm_request_irq(&pdev->dev, sport->port.irq, handler, 0,
+				DRIVER_NAME, sport);
+	if (ret)
+		goto failed_irq_request;
 
 	return 0;
 
-failed_get_rs485:
-failed_reset:
+failed_irq_request:
 	uart_remove_one_port(&lpuart_reg, &sport->port);
 failed_attach_port:
-failed_irq_request:
+failed_get_rs485:
+failed_reset:
 	lpuart_disable_clks(sport);
-failed_clock_enable:
-failed_out_of_range:
-	if (sport->id_allocated)
-		ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
 	return ret;
 }
 
@@ -2779,9 +2870,6 @@
 
 	uart_remove_one_port(&lpuart_reg, &sport->port);
 
-	if (sport->id_allocated)
-		ida_simple_remove(&fsl_lpuart_ida, sport->port.line);
-
 	lpuart_disable_clks(sport);
 
 	if (sport->dma_tx_chan)
@@ -2821,11 +2909,10 @@
 		 * EDMA driver during suspend will forcefully release any
 		 * non-idle DMA channels. If port wakeup is enabled or if port
 		 * is console port or 'no_console_suspend' is set the Rx DMA
-		 * cannot resume as as expected, hence gracefully release the
+		 * cannot resume as expected, hence gracefully release the
 		 * Rx DMA path before suspend and start Rx DMA path on resume.
 		 */
 		if (irq_wake) {
-			del_timer_sync(&sport->lpuart_timer);
 			lpuart_dma_rx_free(&sport->port);
 		}
 
@@ -2911,7 +2998,6 @@
 
 static void __exit lpuart_serial_exit(void)
 {
-	ida_destroy(&fsl_lpuart_ida);
 	platform_driver_unregister(&lpuart_driver);
 	uart_unregister_driver(&lpuart_reg);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/icom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/icom.c
@@ -1501,7 +1501,7 @@
 	retval = pci_read_config_dword(dev, PCI_COMMAND, &command_reg);
 	if (retval) {
 		dev_err(&dev->dev, "PCI Config read FAILED\n");
-		return retval;
+		goto probe_exit0;
 	}
 
 	pci_write_config_dword(dev, PCI_COMMAND,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/imx.c
@@ -27,6 +27,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/dma-mapping.h>
 
 #include <asm/irq.h>
@@ -380,8 +381,7 @@
 {
 	*ucr2 &= ~(UCR2_CTSC | UCR2_CTS);
 
-	sport->port.mctrl |= TIOCM_RTS;
-	mctrl_gpio_set(sport->gpios, sport->port.mctrl);
+	mctrl_gpio_set(sport->gpios, sport->port.mctrl | TIOCM_RTS);
 }
 
 /* called with port.lock taken and irqs caller dependent */
@@ -390,8 +390,7 @@
 	*ucr2 &= ~UCR2_CTSC;
 	*ucr2 |= UCR2_CTS;
 
-	sport->port.mctrl &= ~TIOCM_RTS;
-	mctrl_gpio_set(sport->gpios, sport->port.mctrl);
+	mctrl_gpio_set(sport->gpios, sport->port.mctrl & ~TIOCM_RTS);
 }
 
 static void start_hrtimer_ms(struct hrtimer *hrt, unsigned long msec)
@@ -399,6 +398,16 @@
        hrtimer_start(hrt, ms_to_ktime(msec), HRTIMER_MODE_REL);
 }
 
+static void imx_uart_disable_loopback_rs485(struct imx_port *sport)
+{
+	unsigned int uts;
+
+	/* See SER_RS485_ENABLED/UTS_LOOP comment in imx_uart_probe() */
+	uts = imx_uart_readl(sport, imx_uart_uts_reg(sport));
+	uts &= ~UTS_LOOP;
+	imx_uart_writel(sport, uts, imx_uart_uts_reg(sport));
+}
+
 /* called with port.lock taken and irqs off */
 static void imx_uart_start_rx(struct uart_port *port)
 {
@@ -420,6 +429,7 @@
 	/* Write UCR2 first as it includes RXEN */
 	imx_uart_writel(sport, ucr2, UCR2);
 	imx_uart_writel(sport, ucr1, UCR1);
+	imx_uart_disable_loopback_rs485(sport);
 }
 
 /* called with port.lock taken and irqs off */
@@ -441,13 +451,13 @@
 	ucr1 = imx_uart_readl(sport, UCR1);
 	imx_uart_writel(sport, ucr1 & ~UCR1_TRDYEN, UCR1);
 
+	ucr4 = imx_uart_readl(sport, UCR4);
 	usr2 = imx_uart_readl(sport, USR2);
-	if (!(usr2 & USR2_TXDC)) {
+	if ((!(usr2 & USR2_TXDC)) && (ucr4 & UCR4_TCEN)) {
 		/* The shifter is still busy, so retry once TC triggers */
 		return;
 	}
 
-	ucr4 = imx_uart_readl(sport, UCR4);
 	ucr4 &= ~UCR4_TCEN;
 	imx_uart_writel(sport, ucr4, UCR4);
 
@@ -482,28 +492,51 @@
 	}
 }
 
-/* called with port.lock taken and irqs off */
-static void imx_uart_stop_rx(struct uart_port *port)
+static void imx_uart_stop_rx_with_loopback_ctrl(struct uart_port *port, bool loopback)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	u32 ucr1, ucr2;
+	u32 ucr1, ucr2, ucr4, uts;
 
 	ucr1 = imx_uart_readl(sport, UCR1);
 	ucr2 = imx_uart_readl(sport, UCR2);
+	ucr4 = imx_uart_readl(sport, UCR4);
 
 	if (sport->dma_is_enabled) {
 		ucr1 &= ~(UCR1_RXDMAEN | UCR1_ATDMAEN);
 	} else {
 		ucr1 &= ~UCR1_RRDYEN;
 		ucr2 &= ~UCR2_ATEN;
+		ucr4 &= ~UCR4_OREN;
 	}
 	imx_uart_writel(sport, ucr1, UCR1);
+	imx_uart_writel(sport, ucr4, UCR4);
+
+	/* See SER_RS485_ENABLED/UTS_LOOP comment in imx_uart_probe() */
+	if (port->rs485.flags & SER_RS485_ENABLED &&
+	    port->rs485.flags & SER_RS485_RTS_ON_SEND &&
+	    sport->have_rtscts && !sport->have_rtsgpio && loopback) {
+		uts = imx_uart_readl(sport, imx_uart_uts_reg(sport));
+		uts |= UTS_LOOP;
+		imx_uart_writel(sport, uts, imx_uart_uts_reg(sport));
+		ucr2 |= UCR2_RXEN;
+	} else {
+		ucr2 &= ~UCR2_RXEN;
+	}
 
-	ucr2 &= ~UCR2_RXEN;
 	imx_uart_writel(sport, ucr2, UCR2);
 }
 
 /* called with port.lock taken and irqs off */
+static void imx_uart_stop_rx(struct uart_port *port)
+{
+	/*
+	 * Stop RX and enable loopback in order to make sure RS485 bus
+	 * is not blocked. Se comment in imx_uart_probe().
+	 */
+	imx_uart_stop_rx_with_loopback_ctrl(port, true);
+}
+
+/* called with port.lock taken and irqs off */
 static void imx_uart_enable_ms(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
@@ -691,8 +724,13 @@
 				imx_uart_rts_inactive(sport, &ucr2);
 			imx_uart_writel(sport, ucr2, UCR2);
 
+			/*
+			 * Since we are about to transmit we can not stop RX
+			 * with loopback enabled because that will make our
+			 * transmitted data being just looped to RX.
+			 */
 			if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
-				imx_uart_stop_rx(port);
+				imx_uart_stop_rx_with_loopback_ctrl(port, false);
 
 			sport->tx_state = WAIT_AFTER_RTS;
 			start_hrtimer_ms(&sport->trigger_start_tx,
@@ -1435,7 +1473,7 @@
 	imx_uart_writel(sport, ucr1, UCR1);
 
 	ucr4 = imx_uart_readl(sport, UCR4) & ~(UCR4_OREN | UCR4_INVR);
-	if (!sport->dma_is_enabled)
+	if (!dma_is_inited)
 		ucr4 |= UCR4_OREN;
 	if (sport->inverted_rx)
 		ucr4 |= UCR4_INVR;
@@ -1487,6 +1525,8 @@
 		imx_uart_writel(sport, ucr2, UCR2);
 	}
 
+	imx_uart_disable_loopback_rs485(sport);
+
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 
 	return 0;
@@ -1496,7 +1536,7 @@
 {
 	struct imx_port *sport = (struct imx_port *)port;
 	unsigned long flags;
-	u32 ucr1, ucr2, ucr4;
+	u32 ucr1, ucr2, ucr4, uts;
 
 	if (sport->dma_is_enabled) {
 		dmaengine_terminate_sync(sport->dma_chan_tx);
@@ -1540,11 +1580,22 @@
 	spin_lock_irqsave(&sport->port.lock, flags);
 
 	ucr1 = imx_uart_readl(sport, UCR1);
-	ucr1 &= ~(UCR1_TRDYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN | UCR1_RXDMAEN | UCR1_ATDMAEN);
+	ucr1 &= ~(UCR1_TRDYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_RXDMAEN | UCR1_ATDMAEN);
+	/* See SER_RS485_ENABLED/UTS_LOOP comment in imx_uart_probe() */
+	if (port->rs485.flags & SER_RS485_ENABLED &&
+	    port->rs485.flags & SER_RS485_RTS_ON_SEND &&
+	    sport->have_rtscts && !sport->have_rtsgpio) {
+		uts = imx_uart_readl(sport, imx_uart_uts_reg(sport));
+		uts |= UTS_LOOP;
+		imx_uart_writel(sport, uts, imx_uart_uts_reg(sport));
+		ucr1 |= UCR1_UARTEN;
+	} else {
+		ucr1 &= ~UCR1_UARTEN;
+	}
 	imx_uart_writel(sport, ucr1, UCR1);
 
 	ucr4 = imx_uart_readl(sport, UCR4);
-	ucr4 &= ~(UCR4_OREN | UCR4_TCEN);
+	ucr4 &= ~UCR4_TCEN;
 	imx_uart_writel(sport, ucr4, UCR4);
 
 	spin_unlock_irqrestore(&sport->port.lock, flags);
@@ -1894,7 +1945,7 @@
 #endif
 
 /* called with port.lock taken and irqs off or from .probe without locking */
-static int imx_uart_rs485_config(struct uart_port *port,
+static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termios,
 				 struct serial_rs485 *rs485conf)
 {
 	struct imx_port *sport = (struct imx_port *)port;
@@ -1974,7 +2025,7 @@
 	struct imx_port *sport = imx_uart_ports[co->index];
 	struct imx_port_ucrs old_ucr;
 	unsigned long flags;
-	unsigned int ucr1;
+	unsigned int ucr1, usr2;
 	int locked = 1;
 
 	if (sport->port.sysrq)
@@ -2005,8 +2056,8 @@
 	 *	Finally, wait for transmitter to become empty
 	 *	and restore UCR1/2/3
 	 */
-	while (!(imx_uart_readl(sport, USR2) & USR2_TXDC));
-
+	read_poll_timeout_atomic(imx_uart_readl, usr2, usr2 & USR2_TXDC,
+				 0, USEC_PER_SEC, false, sport, USR2);
 	imx_uart_ucrs_restore(sport, &old_ucr);
 
 	if (locked)
@@ -2017,7 +2068,7 @@
  * If the port was already initialised (eg, by a boot loader),
  * try to determine the current setup.
  */
-static void __init
+static void
 imx_uart_console_get_options(struct imx_port *sport, int *baud,
 			     int *parity, int *bits)
 {
@@ -2076,7 +2127,7 @@
 	}
 }
 
-static int __init
+static int
 imx_uart_console_setup(struct console *co, char *options)
 {
 	struct imx_port *sport;
@@ -2188,7 +2239,7 @@
 	void __iomem *base;
 	u32 dma_buf_conf[2];
 	int ret = 0;
-	u32 ucr1;
+	u32 ucr1, ucr2, uts;
 	struct resource *res;
 	int txirq, rxirq, rtsirq;
 
@@ -2282,7 +2333,7 @@
 	/* For register access, we only need to enable the ipg clock. */
 	ret = clk_prepare_enable(sport->clk_ipg);
 	if (ret) {
-		dev_err(&pdev->dev, "failed to enable per clk: %d\n", ret);
+		dev_err(&pdev->dev, "failed to enable ipg clk: %d\n", ret);
 		return ret;
 	}
 
@@ -2294,10 +2345,8 @@
 	sport->ufcr = readl(sport->port.membase + UFCR);
 
 	ret = uart_get_rs485_mode(&sport->port);
-	if (ret) {
-		clk_disable_unprepare(sport->clk_ipg);
-		return ret;
-	}
+	if (ret)
+		goto err_clk;
 
 	if (sport->port.rs485.flags & SER_RS485_ENABLED &&
 	    (!sport->have_rtscts && !sport->have_rtsgpio))
@@ -2315,13 +2364,41 @@
 		dev_err(&pdev->dev,
 			"low-active RTS not possible when receiver is off, enabling receiver\n");
 
-	imx_uart_rs485_config(&sport->port, &sport->port.rs485);
-
 	/* Disable interrupts before requesting them */
 	ucr1 = imx_uart_readl(sport, UCR1);
 	ucr1 &= ~(UCR1_ADEN | UCR1_TRDYEN | UCR1_IDEN | UCR1_RRDYEN | UCR1_RTSDEN);
 	imx_uart_writel(sport, ucr1, UCR1);
 
+	/* Disable Ageing Timer interrupt */
+	ucr2 = imx_uart_readl(sport, UCR2);
+	ucr2 &= ~UCR2_ATEN;
+	imx_uart_writel(sport, ucr2, UCR2);
+
+	/*
+	 * In case RS485 is enabled without GPIO RTS control, the UART IP
+	 * is used to control CTS signal. Keep both the UART and Receiver
+	 * enabled, otherwise the UART IP pulls CTS signal always HIGH no
+	 * matter how the UCR2 CTSC and CTS bits are set. To prevent any
+	 * data from being fed into the RX FIFO, enable loopback mode in
+	 * UTS register, which disconnects the RX path from external RXD
+	 * pin and connects it to the Transceiver, which is disabled, so
+	 * no data can be fed to the RX FIFO that way.
+	 */
+	if (sport->port.rs485.flags & SER_RS485_ENABLED &&
+	    sport->have_rtscts && !sport->have_rtsgpio) {
+		uts = imx_uart_readl(sport, imx_uart_uts_reg(sport));
+		uts |= UTS_LOOP;
+		imx_uart_writel(sport, uts, imx_uart_uts_reg(sport));
+
+		ucr1 = imx_uart_readl(sport, UCR1);
+		ucr1 |= UCR1_UARTEN;
+		imx_uart_writel(sport, ucr1, UCR1);
+
+		ucr2 = imx_uart_readl(sport, UCR2);
+		ucr2 |= UCR2_RXEN;
+		imx_uart_writel(sport, ucr2, UCR2);
+	}
+
 	if (!imx_uart_is_imx1(sport) && sport->dte_mode) {
 		/*
 		 * The DCEDTE bit changes the direction of DSR, DCD, DTR and RI
@@ -2353,8 +2430,6 @@
 		imx_uart_writel(sport, ucr3, UCR3);
 	}
 
-	clk_disable_unprepare(sport->clk_ipg);
-
 	hrtimer_init(&sport->trigger_start_tx, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
 	hrtimer_init(&sport->trigger_stop_tx, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
 	sport->trigger_start_tx.function = imx_trigger_start_tx;
@@ -2370,7 +2445,7 @@
 		if (ret) {
 			dev_err(&pdev->dev, "failed to request rx irq: %d\n",
 				ret);
-			return ret;
+			goto err_clk;
 		}
 
 		ret = devm_request_irq(&pdev->dev, txirq, imx_uart_txint, 0,
@@ -2378,7 +2453,7 @@
 		if (ret) {
 			dev_err(&pdev->dev, "failed to request tx irq: %d\n",
 				ret);
-			return ret;
+			goto err_clk;
 		}
 
 		ret = devm_request_irq(&pdev->dev, rtsirq, imx_uart_rtsint, 0,
@@ -2386,14 +2461,14 @@
 		if (ret) {
 			dev_err(&pdev->dev, "failed to request rts irq: %d\n",
 				ret);
-			return ret;
+			goto err_clk;
 		}
 	} else {
 		ret = devm_request_irq(&pdev->dev, rxirq, imx_uart_int, 0,
 				       dev_name(&pdev->dev), sport);
 		if (ret) {
 			dev_err(&pdev->dev, "failed to request irq: %d\n", ret);
-			return ret;
+			goto err_clk;
 		}
 	}
 
@@ -2401,7 +2476,12 @@
 
 	platform_set_drvdata(pdev, sport);
 
-	return uart_add_one_port(&imx_uart_uart_driver, &sport->port);
+	ret = uart_add_one_port(&imx_uart_uart_driver, &sport->port);
+
+err_clk:
+	clk_disable_unprepare(sport->clk_ipg);
+
+	return ret;
 }
 
 static int imx_uart_remove(struct platform_device *pdev)
@@ -2564,6 +2644,7 @@
 	.suspend_noirq = imx_uart_suspend_noirq,
 	.resume_noirq = imx_uart_resume_noirq,
 	.freeze_noirq = imx_uart_suspend_noirq,
+	.thaw_noirq = imx_uart_resume_noirq,
 	.restore_noirq = imx_uart_resume_noirq,
 	.suspend = imx_uart_suspend,
 	.resume = imx_uart_resume,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/jsm/jsm_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/jsm/jsm_driver.c
@@ -211,7 +211,8 @@
 
 		break;
 	default:
-		return -ENXIO;
+		rc = -ENXIO;
+		goto out_kfree_brd;
 	}
 
 	rc = request_irq(brd->irq, brd->bd_ops->intr, IRQF_SHARED, "JSM", brd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/kgdboc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/kgdboc.c
@@ -19,6 +19,7 @@
 #include <linux/console.h>
 #include <linux/vt_kern.h>
 #include <linux/input.h>
+#include <linux/irq_work.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
@@ -48,6 +49,25 @@
 static int                      (*earlycon_orig_exit)(struct console *con);
 #endif /* IS_BUILTIN(CONFIG_KGDB_SERIAL_CONSOLE) */
 
+/*
+ * When we leave the debug trap handler we need to reset the keyboard status
+ * (since the original keyboard state gets partially clobbered by kdb use of
+ * the keyboard).
+ *
+ * The path to deliver the reset is somewhat circuitous.
+ *
+ * To deliver the reset we register an input handler, reset the keyboard and
+ * then deregister the input handler. However, to get this done right, we do
+ * have to carefully manage the calling context because we can only register
+ * input handlers from task context.
+ *
+ * In particular we need to trigger the action from the debug trap handler with
+ * all its NMI and/or NMI-like oddities. To solve this the kgdboc trap exit code
+ * (the "post_exception" callback) uses irq_work_queue(), which is NMI-safe, to
+ * schedule a callback from a hardirq context. From there we have to defer the
+ * work again, this time using schedule_work(), to get a callback using the
+ * system workqueue, which runs in task context.
+ */
 #ifdef CONFIG_KDB_KEYBOARD
 static int kgdboc_reset_connect(struct input_handler *handler,
 				struct input_dev *dev,
@@ -99,10 +119,17 @@
 
 static DECLARE_WORK(kgdboc_restore_input_work, kgdboc_restore_input_helper);
 
+static void kgdboc_queue_restore_input_helper(struct irq_work *unused)
+{
+	schedule_work(&kgdboc_restore_input_work);
+}
+
+static DEFINE_IRQ_WORK(kgdboc_restore_input_irq_work, kgdboc_queue_restore_input_helper);
+
 static void kgdboc_restore_input(void)
 {
 	if (likely(system_state == SYSTEM_RUNNING))
-		schedule_work(&kgdboc_restore_input_work);
+		irq_work_queue(&kgdboc_restore_input_irq_work);
 }
 
 static int kgdboc_register_kbd(char **cptr)
@@ -133,6 +160,7 @@
 			i--;
 		}
 	}
+	irq_work_sync(&kgdboc_restore_input_irq_work);
 	flush_work(&kgdboc_restore_input_work);
 }
 #else /* ! CONFIG_KDB_KEYBOARD */
@@ -403,16 +431,16 @@
 {
 	if (!opt) {
 		pr_err("config string not provided\n");
-		return -EINVAL;
+		return 1;
 	}
 
 	if (strlen(opt) >= MAX_CONFIG_LEN) {
 		pr_err("config string too long\n");
-		return -ENOSPC;
+		return 1;
 	}
 	strcpy(config, opt);
 
-	return 0;
+	return 1;
 }
 
 __setup("kgdboc=", kgdboc_option_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/lantiq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/lantiq.c
@@ -274,6 +274,7 @@
 	struct ltq_uart_port *ltq_port = to_ltq_uart_port(port);
 
 	spin_lock_irqsave(&ltq_port->lock, flags);
+	__raw_writel(ASC_IRNCR_EIR, port->membase + LTQ_ASC_IRNCR);
 	/* clear any pending interrupts */
 	asc_update_bits(0, ASCWHBSTATE_CLRPE | ASCWHBSTATE_CLRFE |
 		ASCWHBSTATE_CLRROE, port->membase + LTQ_ASC_WHBSTATE);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/liteuart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/liteuart.c
@@ -270,8 +270,10 @@
 
 	/* get membase */
 	port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, NULL);
-	if (IS_ERR(port->membase))
-		return PTR_ERR(port->membase);
+	if (IS_ERR(port->membase)) {
+		ret = PTR_ERR(port->membase);
+		goto err_erase_id;
+	}
 
 	/* values not from device tree */
 	port->dev = &pdev->dev;
@@ -285,7 +287,18 @@
 	port->line = dev_id;
 	spin_lock_init(&port->lock);
 
-	return uart_add_one_port(&liteuart_driver, &uart->port);
+	platform_set_drvdata(pdev, port);
+
+	ret = uart_add_one_port(&liteuart_driver, &uart->port);
+	if (ret)
+		goto err_erase_id;
+
+	return 0;
+
+err_erase_id:
+	xa_erase(&liteuart_array, uart->id);
+
+	return ret;
 }
 
 static int liteuart_remove(struct platform_device *pdev)
@@ -293,6 +306,7 @@
 	struct uart_port *port = platform_get_drvdata(pdev);
 	struct liteuart_port *uart = to_liteuart_port(port);
 
+	uart_remove_one_port(&liteuart_driver, port);
 	xa_erase(&liteuart_array, uart->id);
 
 	return 0;
@@ -422,4 +436,4 @@
 MODULE_AUTHOR("Antmicro <www.antmicro.com>");
 MODULE_DESCRIPTION("LiteUART serial driver");
 MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform: liteuart");
+MODULE_ALIAS("platform:liteuart");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/lpc32xx_hs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/lpc32xx_hs.c
@@ -341,7 +341,7 @@
 		       LPC32XX_HSUART_IIR(port->membase));
 		port->icount.overrun++;
 		tty_insert_flip_char(tport, 0, TTY_OVERRUN);
-		tty_schedule_flip(tport);
+		tty_flip_buffer_push(tport);
 	}
 
 	/* Data received? */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/max3100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/max3100.c
@@ -45,6 +45,9 @@
 #include <linux/freezer.h>
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
+#include <linux/types.h>
+
+#include <asm/unaligned.h>
 
 #include <linux/serial_max3100.h>
 
@@ -191,7 +194,7 @@
 static int max3100_sr(struct max3100_port *s, u16 tx, u16 *rx)
 {
 	struct spi_message message;
-	u16 etx, erx;
+	__be16 etx, erx;
 	int status;
 	struct spi_transfer tran = {
 		.tx_buf = &etx,
@@ -213,7 +216,7 @@
 	return 0;
 }
 
-static int max3100_handlerx(struct max3100_port *s, u16 rx)
+static int max3100_handlerx_unlocked(struct max3100_port *s, u16 rx)
 {
 	unsigned int ch, flg, status = 0;
 	int ret = 0, cts;
@@ -253,6 +256,17 @@
 	return ret;
 }
 
+static int max3100_handlerx(struct max3100_port *s, u16 rx)
+{
+	unsigned long flags;
+	int ret;
+
+	uart_port_lock_irqsave(&s->port, &flags);
+	ret = max3100_handlerx_unlocked(s, rx);
+	uart_port_unlock_irqrestore(&s->port, flags);
+	return ret;
+}
+
 static void max3100_work(struct work_struct *w)
 {
 	struct max3100_port *s = container_of(w, struct max3100_port, work);
@@ -740,13 +754,14 @@
 	mutex_lock(&max3100s_lock);
 
 	if (!uart_driver_registered) {
-		uart_driver_registered = 1;
 		retval = uart_register_driver(&max3100_uart_driver);
 		if (retval) {
 			printk(KERN_ERR "Couldn't register max3100 uart driver\n");
 			mutex_unlock(&max3100s_lock);
 			return retval;
 		}
+
+		uart_driver_registered = 1;
 	}
 
 	for (i = 0; i < MAX_MAX3100; i++)
@@ -832,6 +847,7 @@
 		}
 	pr_debug("removing max3100 driver\n");
 	uart_unregister_driver(&max3100_uart_driver);
+	uart_driver_registered = 0;
 
 	mutex_unlock(&max3100s_lock);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/max310x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/max310x.c
@@ -72,7 +72,7 @@
 #define MAX310X_GLOBALCMD_REG		MAX310X_REG_1F /* Global Command (WO) */
 
 /* Extended registers */
-#define MAX310X_REVID_EXTREG		MAX310X_REG_05 /* Revision ID */
+#define MAX310X_SPI_REVID_EXTREG	MAX310X_REG_05 /* Revision ID */
 
 /* IRQ register bits */
 #define MAX310X_IRQ_LSR_BIT		(1 << 0) /* LSR interrupt */
@@ -235,6 +235,14 @@
 #define MAX310x_REV_MASK		(0xf8)
 #define MAX310X_WRITE_BIT		0x80
 
+/* Port startup definitions */
+#define MAX310X_PORT_STARTUP_WAIT_RETRIES	20 /* Number of retries */
+#define MAX310X_PORT_STARTUP_WAIT_DELAY_MS	10 /* Delay between retries */
+
+/* Crystal-related definitions */
+#define MAX310X_XTAL_WAIT_RETRIES	20 /* Number of retries */
+#define MAX310X_XTAL_WAIT_DELAY_MS	10 /* Delay between retries */
+
 /* MAX3107 specific */
 #define MAX3107_REV_ID			(0xa0)
 
@@ -245,6 +253,12 @@
 #define MAX14830_BRGCFG_CLKDIS_BIT	(1 << 6) /* Clock Disable */
 #define MAX14830_REV_ID			(0xb0)
 
+struct max310x_if_cfg {
+	int (*extended_reg_enable)(struct device *dev, bool enable);
+
+	unsigned int rev_id_reg;
+};
+
 struct max310x_devtype {
 	char	name[9];
 	int	nr;
@@ -258,9 +272,8 @@
 	struct work_struct	tx_work;
 	struct work_struct	md_work;
 	struct work_struct	rs_work;
+	struct regmap		*regmap;
 
-	u8 wr_header;
-	u8 rd_header;
 	u8 rx_buf[MAX310X_FIFO_SIZE];
 };
 #define to_max310x_port(_port) \
@@ -268,6 +281,7 @@
 
 struct max310x_port {
 	const struct max310x_devtype *devtype;
+	const struct max310x_if_cfg *if_cfg;
 	struct regmap		*regmap;
 	struct clk		*clk;
 #ifdef CONFIG_GPIOLIB
@@ -289,26 +303,26 @@
 
 static u8 max310x_port_read(struct uart_port *port, u8 reg)
 {
-	struct max310x_port *s = dev_get_drvdata(port->dev);
+	struct max310x_one *one = to_max310x_port(port);
 	unsigned int val = 0;
 
-	regmap_read(s->regmap, port->iobase + reg, &val);
+	regmap_read(one->regmap, reg, &val);
 
 	return val;
 }
 
 static void max310x_port_write(struct uart_port *port, u8 reg, u8 val)
 {
-	struct max310x_port *s = dev_get_drvdata(port->dev);
+	struct max310x_one *one = to_max310x_port(port);
 
-	regmap_write(s->regmap, port->iobase + reg, val);
+	regmap_write(one->regmap, reg, val);
 }
 
 static void max310x_port_update(struct uart_port *port, u8 reg, u8 mask, u8 val)
 {
-	struct max310x_port *s = dev_get_drvdata(port->dev);
+	struct max310x_one *one = to_max310x_port(port);
 
-	regmap_update_bits(s->regmap, port->iobase + reg, mask, val);
+	regmap_update_bits(one->regmap, reg, mask, val);
 }
 
 static int max3107_detect(struct device *dev)
@@ -357,13 +371,12 @@
 	unsigned int val = 0;
 	int ret;
 
-	ret = regmap_write(s->regmap, MAX310X_GLOBALCMD_REG,
-			   MAX310X_EXTREG_ENBL);
+	ret = s->if_cfg->extended_reg_enable(dev, true);
 	if (ret)
 		return ret;
 
-	regmap_read(s->regmap, MAX310X_REVID_EXTREG, &val);
-	regmap_write(s->regmap, MAX310X_GLOBALCMD_REG, MAX310X_EXTREG_DSBL);
+	regmap_read(s->regmap, s->if_cfg->rev_id_reg, &val);
+	s->if_cfg->extended_reg_enable(dev, false);
 	if (((val & MAX310x_REV_MASK) != MAX3109_REV_ID)) {
 		dev_err(dev,
 			"%s ID 0x%02x does not match\n", s->devtype->name, val);
@@ -388,13 +401,12 @@
 	unsigned int val = 0;
 	int ret;
 
-	ret = regmap_write(s->regmap, MAX310X_GLOBALCMD_REG,
-			   MAX310X_EXTREG_ENBL);
+	ret = s->if_cfg->extended_reg_enable(dev, true);
 	if (ret)
 		return ret;
 	
-	regmap_read(s->regmap, MAX310X_REVID_EXTREG, &val);
-	regmap_write(s->regmap, MAX310X_GLOBALCMD_REG, MAX310X_EXTREG_DSBL);
+	regmap_read(s->regmap, s->if_cfg->rev_id_reg, &val);
+	s->if_cfg->extended_reg_enable(dev, false);
 	if (((val & MAX310x_REV_MASK) != MAX14830_REV_ID)) {
 		dev_err(dev,
 			"%s ID 0x%02x does not match\n", s->devtype->name, val);
@@ -447,7 +459,7 @@
 
 static bool max310x_reg_writeable(struct device *dev, unsigned int reg)
 {
-	switch (reg & 0x1f) {
+	switch (reg) {
 	case MAX310X_IRQSTS_REG:
 	case MAX310X_LSR_IRQSTS_REG:
 	case MAX310X_SPCHR_IRQSTS_REG:
@@ -464,7 +476,7 @@
 
 static bool max310x_reg_volatile(struct device *dev, unsigned int reg)
 {
-	switch (reg & 0x1f) {
+	switch (reg) {
 	case MAX310X_RHR_REG:
 	case MAX310X_IRQSTS_REG:
 	case MAX310X_LSR_IRQSTS_REG:
@@ -486,7 +498,7 @@
 
 static bool max310x_reg_precious(struct device *dev, unsigned int reg)
 {
-	switch (reg & 0x1f) {
+	switch (reg) {
 	case MAX310X_RHR_REG:
 	case MAX310X_IRQSTS_REG:
 	case MAX310X_SPCHR_IRQSTS_REG:
@@ -499,6 +511,11 @@
 	return false;
 }
 
+static bool max310x_reg_noinc(struct device *dev, unsigned int reg)
+{
+	return reg == MAX310X_RHR_REG;
+}
+
 static int max310x_set_baud(struct uart_port *port, int baud)
 {
 	unsigned int mode = 0, div = 0, frac = 0, c = 0, F = 0;
@@ -552,7 +569,7 @@
 	return 1;
 }
 
-static u32 max310x_set_ref_clk(struct device *dev, struct max310x_port *s,
+static s32 max310x_set_ref_clk(struct device *dev, struct max310x_port *s,
 			       unsigned long freq, bool xtal)
 {
 	unsigned int div, clksrc, pllcfg = 0;
@@ -610,12 +627,20 @@
 
 	/* Wait for crystal */
 	if (xtal) {
-		unsigned int val;
-		msleep(10);
-		regmap_read(s->regmap, MAX310X_STS_IRQSTS_REG, &val);
-		if (!(val & MAX310X_STS_CLKREADY_BIT)) {
-			dev_warn(dev, "clock is not stable yet\n");
-		}
+		bool stable = false;
+		unsigned int try = 0, val = 0;
+
+		do {
+			msleep(MAX310X_XTAL_WAIT_DELAY_MS);
+			regmap_read(s->regmap, MAX310X_STS_IRQSTS_REG, &val);
+
+			if (val & MAX310X_STS_CLKREADY_BIT)
+				stable = true;
+		} while (!stable && (++try < MAX310X_XTAL_WAIT_RETRIES));
+
+		if (!stable)
+			return dev_err_probe(dev, -EAGAIN,
+					     "clock is not stable\n");
 	}
 
 	return bestfreq;
@@ -624,31 +649,15 @@
 static void max310x_batch_write(struct uart_port *port, u8 *txbuf, unsigned int len)
 {
 	struct max310x_one *one = to_max310x_port(port);
-	struct spi_transfer xfer[] = {
-		{
-			.tx_buf = &one->wr_header,
-			.len = sizeof(one->wr_header),
-		}, {
-			.tx_buf = txbuf,
-			.len = len,
-		}
-	};
-	spi_sync_transfer(to_spi_device(port->dev), xfer, ARRAY_SIZE(xfer));
+
+	regmap_noinc_write(one->regmap, MAX310X_THR_REG, txbuf, len);
 }
 
 static void max310x_batch_read(struct uart_port *port, u8 *rxbuf, unsigned int len)
 {
 	struct max310x_one *one = to_max310x_port(port);
-	struct spi_transfer xfer[] = {
-		{
-			.tx_buf = &one->rd_header,
-			.len = sizeof(one->rd_header),
-		}, {
-			.rx_buf = rxbuf,
-			.len = len,
-		}
-	};
-	spi_sync_transfer(to_spi_device(port->dev), xfer, ARRAY_SIZE(xfer));
+
+	regmap_noinc_read(one->regmap, MAX310X_RHR_REG, rxbuf, len);
 }
 
 static void max310x_handle_rx(struct uart_port *port, unsigned int rxlen)
@@ -1026,7 +1035,7 @@
 			MAX310X_MODE2_ECHOSUPR_BIT, mode2);
 }
 
-static int max310x_rs485_config(struct uart_port *port,
+static int max310x_rs485_config(struct uart_port *port, struct ktermios *termios,
 				struct serial_rs485 *rs485)
 {
 	struct max310x_one *one = to_max310x_port(port);
@@ -1251,15 +1260,17 @@
 #endif
 
 static int max310x_probe(struct device *dev, const struct max310x_devtype *devtype,
-			 struct regmap *regmap, int irq)
+			 const struct max310x_if_cfg *if_cfg,
+			 struct regmap *regmaps[], int irq)
 {
 	int i, ret, fmin, fmax, freq;
 	struct max310x_port *s;
-	u32 uartclk = 0;
+	s32 uartclk = 0;
 	bool xtal;
 
-	if (IS_ERR(regmap))
-		return PTR_ERR(regmap);
+	for (i = 0; i < devtype->nr; i++)
+		if (IS_ERR(regmaps[i]))
+			return PTR_ERR(regmaps[i]);
 
 	/* Alloc port structure */
 	s = devm_kzalloc(dev, struct_size(s, p, devtype->nr), GFP_KERNEL);
@@ -1306,8 +1317,9 @@
 		goto out_clk;
 	}
 
-	s->regmap = regmap;
+	s->regmap = regmaps[0];
 	s->devtype = devtype;
+	s->if_cfg = if_cfg;
 	dev_set_drvdata(dev, s);
 
 	/* Check device to ensure we are talking to what we expect */
@@ -1316,25 +1328,38 @@
 		goto out_clk;
 
 	for (i = 0; i < devtype->nr; i++) {
-		unsigned int offs = i << 5;
+		bool started = false;
+		unsigned int try = 0, val = 0;
 
 		/* Reset port */
-		regmap_write(s->regmap, MAX310X_MODE2_REG + offs,
+		regmap_write(regmaps[i], MAX310X_MODE2_REG,
 			     MAX310X_MODE2_RST_BIT);
 		/* Clear port reset */
-		regmap_write(s->regmap, MAX310X_MODE2_REG + offs, 0);
+		regmap_write(regmaps[i], MAX310X_MODE2_REG, 0);
 
 		/* Wait for port startup */
 		do {
-			regmap_read(s->regmap,
-				    MAX310X_BRGDIVLSB_REG + offs, &ret);
-		} while (ret != 0x01);
+			msleep(MAX310X_PORT_STARTUP_WAIT_DELAY_MS);
+			regmap_read(regmaps[i], MAX310X_BRGDIVLSB_REG, &val);
+
+			if (val == 0x01)
+				started = true;
+		} while (!started && (++try < MAX310X_PORT_STARTUP_WAIT_RETRIES));
+
+		if (!started) {
+			ret = dev_err_probe(dev, -EAGAIN, "port reset failed\n");
+			goto out_uart;
+		}
 
-		regmap_write(s->regmap, MAX310X_MODE1_REG + offs,
-			     devtype->mode1);
+		regmap_write(regmaps[i], MAX310X_MODE1_REG, devtype->mode1);
 	}
 
 	uartclk = max310x_set_ref_clk(dev, s, freq, xtal);
+	if (uartclk < 0) {
+		ret = uartclk;
+		goto out_uart;
+	}
+
 	dev_dbg(dev, "Reference clock set to %i Hz\n", uartclk);
 
 	for (i = 0; i < devtype->nr; i++) {
@@ -1354,11 +1379,13 @@
 		s->p[i].port.fifosize	= MAX310X_FIFO_SIZE;
 		s->p[i].port.flags	= UPF_FIXED_TYPE | UPF_LOW_LATENCY;
 		s->p[i].port.iotype	= UPIO_PORT;
-		s->p[i].port.iobase	= i * 0x20;
+		s->p[i].port.iobase	= i;
 		s->p[i].port.membase	= (void __iomem *)~0;
 		s->p[i].port.uartclk	= uartclk;
 		s->p[i].port.rs485_config = max310x_rs485_config;
 		s->p[i].port.ops	= &max310x_ops;
+		s->p[i].regmap		= regmaps[i];
+
 		/* Disable all interrupts */
 		max310x_port_write(&s->p[i].port, MAX310X_IRQEN_REG, 0);
 		/* Clear IRQ status register */
@@ -1369,10 +1396,6 @@
 		INIT_WORK(&s->p[i].md_work, max310x_md_proc);
 		/* Initialize queue for changing RS485 mode */
 		INIT_WORK(&s->p[i].rs_work, max310x_rs_proc);
-		/* Initialize SPI-transfer buffers */
-		s->p[i].wr_header = (s->p[i].port.iobase + MAX310X_THR_REG) |
-				    MAX310X_WRITE_BIT;
-		s->p[i].rd_header = (s->p[i].port.iobase + MAX310X_RHR_REG);
 
 		/* Register port */
 		ret = uart_add_one_port(&max310x_uart, &s->p[i].port);
@@ -1410,7 +1433,7 @@
 	if (!ret)
 		return 0;
 
-	dev_err(dev, "Unable to reguest IRQ %i\n", irq);
+	dev_err(dev, "Unable to request IRQ %i\n", irq);
 
 out_uart:
 	for (i = 0; i < devtype->nr; i++) {
@@ -1459,16 +1482,35 @@
 	.val_bits = 8,
 	.write_flag_mask = MAX310X_WRITE_BIT,
 	.cache_type = REGCACHE_RBTREE,
+	.max_register = MAX310X_REG_1F,
 	.writeable_reg = max310x_reg_writeable,
 	.volatile_reg = max310x_reg_volatile,
 	.precious_reg = max310x_reg_precious,
+	.writeable_noinc_reg = max310x_reg_noinc,
+	.readable_noinc_reg = max310x_reg_noinc,
+	.max_raw_read = MAX310X_FIFO_SIZE,
+	.max_raw_write = MAX310X_FIFO_SIZE,
 };
 
 #ifdef CONFIG_SPI_MASTER
+static int max310x_spi_extended_reg_enable(struct device *dev, bool enable)
+{
+	struct max310x_port *s = dev_get_drvdata(dev);
+
+	return regmap_write(s->regmap, MAX310X_GLOBALCMD_REG,
+			    enable ? MAX310X_EXTREG_ENBL : MAX310X_EXTREG_DSBL);
+}
+
+static const struct max310x_if_cfg __maybe_unused max310x_spi_if_cfg = {
+	.extended_reg_enable = max310x_spi_extended_reg_enable,
+	.rev_id_reg = MAX310X_SPI_REVID_EXTREG,
+};
+
 static int max310x_spi_probe(struct spi_device *spi)
 {
 	const struct max310x_devtype *devtype;
-	struct regmap *regmap;
+	struct regmap *regmaps[4];
+	unsigned int i;
 	int ret;
 
 	/* Setup SPI bus */
@@ -1483,10 +1525,14 @@
 	if (!devtype)
 		devtype = (struct max310x_devtype *)spi_get_device_id(spi)->driver_data;
 
-	regcfg.max_register = devtype->nr * 0x20 - 1;
-	regmap = devm_regmap_init_spi(spi, &regcfg);
+	for (i = 0; i < devtype->nr; i++) {
+		u8 port_mask = i * 0x20;
+		regcfg.read_flag_mask = port_mask;
+		regcfg.write_flag_mask = port_mask | MAX310X_WRITE_BIT;
+		regmaps[i] = devm_regmap_init_spi(spi, &regcfg);
+	}
 
-	return max310x_probe(&spi->dev, devtype, regmap, spi->irq);
+	return max310x_probe(&spi->dev, devtype, &max310x_spi_if_cfg, regmaps, spi->irq);
 }
 
 static int max310x_spi_remove(struct spi_device *spi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/mcf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/mcf.c
@@ -432,7 +432,8 @@
 /****************************************************************************/
 
 /* Enable or disable the RS485 support */
-static int mcf_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
+static int mcf_config_rs485(struct uart_port *port, struct ktermios *termios,
+			    struct serial_rs485 *rs485)
 {
 	unsigned char mr1, mr2;
 
@@ -477,7 +478,7 @@
 	.verify_port	= mcf_verify_port,
 };
 
-static struct mcf_uart mcf_ports[4];
+static struct mcf_uart mcf_ports[10];
 
 #define	MCF_MAXPORTS	ARRAY_SIZE(mcf_ports)
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/meson_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/meson_uart.c
@@ -253,6 +253,14 @@
 	return (port->type == PORT_MESON) ? "meson_uart" : NULL;
 }
 
+/*
+ * This function is called only from probe() using a temporary io mapping
+ * in order to perform a reset before setting up the device. Since the
+ * temporarily mapped region was successfully requested, there can be no
+ * console on this port at this time. Hence it is not necessary for this
+ * function to acquire the port->lock. (Since there is no console on this
+ * port at this time, the port->lock is not initialized yet.)
+ */
 static void meson_uart_reset(struct uart_port *port)
 {
 	u32 val;
@@ -267,9 +275,12 @@
 
 static int meson_uart_startup(struct uart_port *port)
 {
+	unsigned long flags;
 	u32 val;
 	int ret = 0;
 
+	spin_lock_irqsave(&port->lock, flags);
+
 	val = readl(port->membase + AML_UART_CONTROL);
 	val |= AML_UART_CLEAR_ERR;
 	writel(val, port->membase + AML_UART_CONTROL);
@@ -285,6 +296,8 @@
 	val = (AML_UART_RECV_IRQ(1) | AML_UART_XMIT_IRQ(port->fifosize / 2));
 	writel(val, port->membase + AML_UART_MISC);
 
+	spin_unlock_irqrestore(&port->lock, flags);
+
 	ret = request_irq(port->irq, meson_uart_interrupt, 0,
 			  port->name, port);
 
@@ -355,10 +368,14 @@
 	else
 		val |= AML_UART_STOP_BIT_1SB;
 
-	if (cflags & CRTSCTS)
-		val &= ~AML_UART_TWO_WIRE_EN;
-	else
+	if (cflags & CRTSCTS) {
+		if (port->flags & UPF_HARD_FLOW)
+			val &= ~AML_UART_TWO_WIRE_EN;
+		else
+			termios->c_cflag &= ~CRTSCTS;
+	} else {
 		val |= AML_UART_TWO_WIRE_EN;
+	}
 
 	writel(val, port->membase + AML_UART_CONTROL);
 
@@ -713,10 +730,12 @@
 
 static int meson_uart_probe(struct platform_device *pdev)
 {
-	struct resource *res_mem, *res_irq;
+	struct resource *res_mem;
 	struct uart_port *port;
 	u32 fifosize = 64; /* Default is 64, 128 for EE UART_0 */
 	int ret = 0;
+	int irq;
+	bool has_rtscts;
 
 	if (pdev->dev.of_node)
 		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
@@ -739,11 +758,12 @@
 	if (!res_mem)
 		return -ENODEV;
 
-	res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (!res_irq)
-		return -ENODEV;
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
 
 	of_property_read_u32(pdev->dev.of_node, "fifo-size", &fifosize);
+	has_rtscts = of_property_read_bool(pdev->dev.of_node, "uart-has-rtscts");
 
 	if (meson_ports[pdev->id]) {
 		dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
@@ -766,8 +786,10 @@
 	port->iotype = UPIO_MEM;
 	port->mapbase = res_mem->start;
 	port->mapsize = resource_size(res_mem);
-	port->irq = res_irq->start;
+	port->irq = irq;
 	port->flags = UPF_BOOT_AUTOCONF | UPF_LOW_LATENCY;
+	if (has_rtscts)
+		port->flags |= UPF_HARD_FLOW;
 	port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_MESON_CONSOLE);
 	port->dev = &pdev->dev;
 	port->line = pdev->id;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/msm_serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/msm_serial.c
@@ -598,6 +598,9 @@
 	u32 val;
 	int ret;
 
+	if (IS_ENABLED(CONFIG_CONSOLE_POLL))
+		return;
+
 	if (!dma->chan)
 		return;
 
@@ -1585,6 +1588,7 @@
 static void __msm_console_write(struct uart_port *port, const char *s,
 				unsigned int count, bool is_uartdm)
 {
+	unsigned long flags;
 	int i;
 	int num_newlines = 0;
 	bool replaced = false;
@@ -1602,6 +1606,8 @@
 			num_newlines++;
 	count += num_newlines;
 
+	local_irq_save(flags);
+
 	if (port->sysrq)
 		locked = 0;
 	else if (oops_in_progress)
@@ -1647,6 +1653,8 @@
 
 	if (locked)
 		spin_unlock(&port->lock);
+
+	local_irq_restore(flags);
 }
 
 static void msm_console_write(struct console *co, const char *s,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/mvebu-uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/mvebu-uart.c
@@ -237,6 +237,7 @@
 	struct tty_port *tport = &port->state->port;
 	unsigned char ch = 0;
 	char flag = 0;
+	int ret;
 
 	do {
 		if (status & STAT_RX_RDY(port)) {
@@ -249,6 +250,16 @@
 				port->icount.parity++;
 		}
 
+		/*
+		 * For UART2, error bits are not cleared on buffer read.
+		 * This causes interrupt loop and system hang.
+		 */
+		if (IS_EXTENDED(port) && (status & STAT_BRK_ERR)) {
+			ret = readl(port->membase + UART_STAT);
+			ret |= STAT_BRK_ERR;
+			writel(ret, port->membase + UART_STAT);
+		}
+
 		if (status & STAT_BRK_DET) {
 			port->icount.brk++;
 			status &= ~(STAT_FRM_ERR | STAT_PAR_ERR);
@@ -442,13 +453,13 @@
 	}
 }
 
-static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
+static unsigned int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
 {
 	unsigned int d_divisor, m_divisor;
 	u32 brdv, osamp;
 
 	if (!port->uartclk)
-		return -EOPNOTSUPP;
+		return 0;
 
 	/*
 	 * The baudrate is derived from the UART clock thanks to two divisors:
@@ -472,7 +483,7 @@
 	osamp &= ~OSAMP_DIVISORS_MASK;
 	writel(osamp, port->membase + UART_OSAMP);
 
-	return 0;
+	return DIV_ROUND_CLOSEST(port->uartclk, d_divisor * m_divisor);
 }
 
 static void mvebu_uart_set_termios(struct uart_port *port,
@@ -509,15 +520,11 @@
 	max_baud = 230400;
 
 	baud = uart_get_baud_rate(port, termios, old, min_baud, max_baud);
-	if (mvebu_uart_baud_rate_set(port, baud)) {
-		/* No clock available, baudrate cannot be changed */
-		if (old)
-			baud = uart_get_baud_rate(port, old, NULL,
-						  min_baud, max_baud);
-	} else {
-		tty_termios_encode_baud_rate(termios, baud, baud);
-		uart_update_timeout(port, termios->c_cflag, baud);
-	}
+	baud = mvebu_uart_baud_rate_set(port, baud);
+
+	/* In case baudrate cannot be changed, report previous old value */
+	if (baud == 0 && old)
+		baud = tty_termios_baud_rate(old);
 
 	/* Only the following flag changes are supported */
 	if (old) {
@@ -528,6 +535,11 @@
 		termios->c_cflag |= CS8;
 	}
 
+	if (baud != 0) {
+		tty_termios_encode_baud_rate(termios, baud, baud);
+		uart_update_timeout(port, termios->c_cflag, baud);
+	}
+
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/mxs-auart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/mxs-auart.c
@@ -1094,11 +1094,13 @@
 
 static irqreturn_t mxs_auart_irq_handle(int irq, void *context)
 {
-	u32 istat;
+	u32 istat, stat;
 	struct mxs_auart_port *s = context;
 	u32 mctrl_temp = s->mctrl_prev;
-	u32 stat = mxs_read(s, REG_STAT);
 
+	uart_port_lock(&s->port);
+
+	stat = mxs_read(s, REG_STAT);
 	istat = mxs_read(s, REG_INTR);
 
 	/* ack irq */
@@ -1134,6 +1136,8 @@
 		istat &= ~AUART_INTR_TXIS;
 	}
 
+	uart_port_unlock(&s->port);
+
 	return IRQ_HANDLED;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/omap-serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/omap-serial.c
@@ -1339,7 +1339,8 @@
 
 /* Enable or disable the rs485 support */
 static int
-serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
+serial_omap_config_rs485(struct uart_port *port, struct ktermios *termios,
+			 struct serial_rs485 *rs485)
 {
 	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned int mode;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/owl-uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/owl-uart.c
@@ -731,6 +731,7 @@
 	owl_port->port.uartclk = clk_get_rate(owl_port->clk);
 	if (owl_port->port.uartclk == 0) {
 		dev_err(&pdev->dev, "clock rate is zero\n");
+		clk_disable_unprepare(owl_port->clk);
 		return -EINVAL;
 	}
 	owl_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_LOW_LATENCY;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/pch_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/pch_uart.c
@@ -624,22 +624,6 @@
 	return 0;
 }
 
-static int pop_tx_x(struct eg20t_port *priv, unsigned char *buf)
-{
-	int ret = 0;
-	struct uart_port *port = &priv->port;
-
-	if (port->x_char) {
-		dev_dbg(priv->port.dev, "%s:X character send %02x (%lu)\n",
-			__func__, port->x_char, jiffies);
-		buf[0] = port->x_char;
-		port->x_char = 0;
-		ret = 1;
-	}
-
-	return ret;
-}
-
 static int dma_push_rx(struct eg20t_port *priv, int size)
 {
 	int room;
@@ -723,6 +707,7 @@
 	if (!chan) {
 		dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Tx)\n",
 			__func__);
+		pci_dev_put(dma_dev);
 		return;
 	}
 	priv->chan_tx = chan;
@@ -739,6 +724,7 @@
 			__func__);
 		dma_release_channel(priv->chan_tx);
 		priv->chan_tx = NULL;
+		pci_dev_put(dma_dev);
 		return;
 	}
 
@@ -746,6 +732,8 @@
 	priv->rx_buf_virt = dma_alloc_coherent(port->dev, port->fifosize,
 				    &priv->rx_buf_dma, GFP_KERNEL);
 	priv->chan_rx = chan;
+
+	pci_dev_put(dma_dev);
 }
 
 static void pch_dma_rx_complete(void *arg)
@@ -777,7 +765,7 @@
 	}
 	xmit->tail &= UART_XMIT_SIZE - 1;
 	async_tx_ack(priv->desc_tx);
-	dma_unmap_sg(port->dev, sg, priv->orig_nent, DMA_TO_DEVICE);
+	dma_unmap_sg(port->dev, priv->sg_tx_p, priv->orig_nent, DMA_TO_DEVICE);
 	priv->tx_dma_use = 0;
 	priv->nent = 0;
 	priv->orig_nent = 0;
@@ -889,9 +877,10 @@
 
 	fifo_size = max(priv->fifo_size, 1);
 	tx_empty = 1;
-	if (pop_tx_x(priv, xmit->buf)) {
-		pch_uart_hal_write(priv, xmit->buf, 1);
+	if (port->x_char) {
+		pch_uart_hal_write(priv, &port->x_char, 1);
 		port->icount.tx++;
+		port->x_char = 0;
 		tx_empty = 0;
 		fifo_size--;
 	}
@@ -946,9 +935,11 @@
 	}
 
 	fifo_size = max(priv->fifo_size, 1);
-	if (pop_tx_x(priv, xmit->buf)) {
-		pch_uart_hal_write(priv, xmit->buf, 1);
+
+	if (port->x_char) {
+		pch_uart_hal_write(priv, &port->x_char, 1);
 		port->icount.tx++;
+		port->x_char = 0;
 		fifo_size--;
 	}
 
@@ -1830,7 +1821,7 @@
 	char name[32];
 
 	snprintf(name, sizeof(name), "uart%d_regs", priv->port.line);
-	debugfs_remove(debugfs_lookup(name, NULL));
+	debugfs_lookup_and_remove(name, NULL);
 	uart_remove_one_port(&pch_uart_driver, &priv->port);
 	free_page((unsigned long)priv->rxbuf.buf);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/pmac_zilog.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/pmac_zilog.c
@@ -217,7 +217,6 @@
 {
 	struct tty_port *port;
 	unsigned char ch, r1, drop, flag;
-	int loops = 0;
 
 	/* Sanity check, make sure the old bug is no longer happening */
 	if (uap->port.state == NULL) {
@@ -298,25 +297,12 @@
 		if (r1 & Rx_OVR)
 			tty_insert_flip_char(port, 0, TTY_OVERRUN);
 	next_char:
-		/* We can get stuck in an infinite loop getting char 0 when the
-		 * line is in a wrong HW state, we break that here.
-		 * When that happens, I disable the receive side of the driver.
-		 * Note that what I've been experiencing is a real irq loop where
-		 * I'm getting flooded regardless of the actual port speed.
-		 * Something strange is going on with the HW
-		 */
-		if ((++loops) > 1000)
-			goto flood;
 		ch = read_zsreg(uap, R0);
 		if (!(ch & Rx_CH_AV))
 			break;
 	}
 
 	return true;
- flood:
-	pmz_interrupt_control(uap, 0);
-	pmz_error("pmz: rx irq flood !\n");
-	return true;
 }
 
 static void pmz_status_handle(struct uart_pmac_port *uap)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/qcom_geni_serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/qcom_geni_serial.c
@@ -125,6 +125,7 @@
 	u32 tx_fifo_width;
 	u32 rx_fifo_depth;
 	bool setup;
+	unsigned long clk_rate;
 	int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop);
 	unsigned int baud;
 	void *rx_fifo;
@@ -866,9 +867,10 @@
 	return IRQ_HANDLED;
 }
 
-static void get_tx_fifo_size(struct qcom_geni_serial_port *port)
+static int setup_fifos(struct qcom_geni_serial_port *port)
 {
 	struct uart_port *uport;
+	u32 old_rx_fifo_depth = port->rx_fifo_depth;
 
 	uport = &port->uport;
 	port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se);
@@ -876,6 +878,16 @@
 	port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se);
 	uport->fifosize =
 		(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;
+
+	if (port->rx_fifo && (old_rx_fifo_depth != port->rx_fifo_depth) && port->rx_fifo_depth) {
+		port->rx_fifo = devm_krealloc(uport->dev, port->rx_fifo,
+					      port->rx_fifo_depth * sizeof(u32),
+					      GFP_KERNEL);
+		if (!port->rx_fifo)
+			return -ENOMEM;
+	}
+
+	return 0;
 }
 
 
@@ -890,6 +902,7 @@
 	u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
 	u32 proto;
 	u32 pin_swap;
+	int ret;
 
 	proto = geni_se_read_proto(&port->se);
 	if (proto != GENI_SE_UART) {
@@ -899,7 +912,9 @@
 
 	qcom_geni_serial_stop_rx(uport);
 
-	get_tx_fifo_size(port);
+	ret = setup_fifos(port);
+	if (ret)
+		return ret;
 
 	writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
 
@@ -1008,6 +1023,7 @@
 		goto out_restart_rx;
 
 	uport->uartclk = clk_rate;
+	port->clk_rate = clk_rate;
 	dev_pm_opp_set_rate(uport->dev, clk_rate);
 	ser_clk_cfg = SER_CLK_EN;
 	ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
@@ -1277,10 +1293,13 @@
 
 	if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) {
 		geni_icc_enable(&port->se);
+		if (port->clk_rate)
+			dev_pm_opp_set_rate(uport->dev, port->clk_rate);
 		geni_se_resources_on(&port->se);
 	} else if (new_state == UART_PM_STATE_OFF &&
 			old_state == UART_PM_STATE_ON) {
 		geni_se_resources_off(&port->se);
+		dev_pm_opp_set_rate(uport->dev, 0);
 		geni_icc_disable(&port->se);
 	}
 }
@@ -1429,25 +1448,17 @@
 	platform_set_drvdata(pdev, port);
 	port->handle_rx = console ? handle_rx_console : handle_rx_uart;
 
-	ret = uart_add_one_port(drv, uport);
-	if (ret)
-		return ret;
-
 	irq_set_status_flags(uport->irq, IRQ_NOAUTOEN);
 	ret = devm_request_irq(uport->dev, uport->irq, qcom_geni_serial_isr,
 			IRQF_TRIGGER_HIGH, port->name, uport);
 	if (ret) {
 		dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret);
-		uart_remove_one_port(drv, uport);
 		return ret;
 	}
 
-	/*
-	 * Set pm_runtime status as ACTIVE so that wakeup_irq gets
-	 * enabled/disabled from dev_pm_arm_wake_irq during system
-	 * suspend/resume respectively.
-	 */
-	pm_runtime_set_active(&pdev->dev);
+	ret = uart_add_one_port(drv, uport);
+	if (ret)
+		return ret;
 
 	if (port->wakeup_irq > 0) {
 		device_init_wakeup(&pdev->dev, true);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/rda-uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/rda-uart.c
@@ -262,6 +262,8 @@
 		fallthrough;
 	case CS7:
 		ctrl &= ~RDA_UART_DBITS_8;
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS7;
 		break;
 	default:
 		ctrl |= RDA_UART_DBITS_8;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/rp2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/rp2.c
@@ -598,8 +598,8 @@
 	u32 clk_cfg;
 
 	writew(1, base + RP2_GLOBAL_CMD);
-	readw(base + RP2_GLOBAL_CMD);
 	msleep(100);
+	readw(base + RP2_GLOBAL_CMD);
 	writel(0, base + RP2_CLK_PRESCALER);
 
 	/* TDM clock configuration */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/sa1100.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/sa1100.c
@@ -446,6 +446,8 @@
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
 	quot = uart_get_divisor(port, baud);
 
+	del_timer_sync(&sport->timer);
+
 	spin_lock_irqsave(&sport->port.lock, flags);
 
 	sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS);
@@ -476,8 +478,6 @@
 				UTSR1_TO_SM(UTSR1_ROR);
 	}
 
-	del_timer_sync(&sport->timer);
-
 	/*
 	 * Update the per-port timeout.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/samsung_tty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/samsung_tty.c
@@ -378,8 +378,7 @@
 	/* Enable tx dma mode */
 	ucon = rd_regl(port, S3C2410_UCON);
 	ucon &= ~(S3C64XX_UCON_TXBURST_MASK | S3C64XX_UCON_TXMODE_MASK);
-	ucon |= (dma_get_cache_alignment() >= 16) ?
-		S3C64XX_UCON_TXBURST_16 : S3C64XX_UCON_TXBURST_1;
+	ucon |= S3C64XX_UCON_TXBURST_1;
 	ucon |= S3C64XX_UCON_TXMODE_DMA;
 	wr_regl(port,  S3C2410_UCON, ucon);
 
@@ -675,7 +674,7 @@
 			S3C64XX_UCON_DMASUS_EN |
 			S3C64XX_UCON_TIMEOUT_EN |
 			S3C64XX_UCON_RXMODE_MASK);
-	ucon |= S3C64XX_UCON_RXBURST_16 |
+	ucon |= S3C64XX_UCON_RXBURST_1 |
 			0xf << S3C64XX_UCON_TIMEOUT_SHIFT |
 			S3C64XX_UCON_EMPTYINT_EN |
 			S3C64XX_UCON_TIMEOUT_EN |
@@ -922,11 +921,8 @@
 		return;
 	}
 
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) {
-		spin_unlock(&port->lock);
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(port);
-		spin_lock(&port->lock);
-	}
 
 	if (uart_circ_empty(xmit))
 		s3c24xx_serial_stop_tx(port);
@@ -995,11 +991,10 @@
 		if ((ufstat & info->tx_fifomask) != 0 ||
 		    (ufstat & info->tx_fifofull))
 			return 0;
-
-		return 1;
+		return TIOCSER_TEMT;
 	}
 
-	return s3c24xx_serial_txempty_nofifo(port);
+	return s3c24xx_serial_txempty_nofifo(port) ? TIOCSER_TEMT : 0;
 }
 
 /* no modem control lines */
@@ -1482,8 +1477,12 @@
 			continue;
 
 		rate = clk_get_rate(clk);
-		if (!rate)
+		if (!rate) {
+			dev_err(ourport->port.dev,
+				"Failed to get clock rate for %s.\n", clkname);
+			clk_put(clk);
 			continue;
+		}
 
 		if (ourport->info->has_divslot) {
 			unsigned long div = rate / req_baud;
@@ -1509,10 +1508,18 @@
 			calc_deviation = -calc_deviation;
 
 		if (calc_deviation < deviation) {
+			/*
+			 * If we find a better clk, release the previous one, if
+			 * any.
+			 */
+			if (!IS_ERR(*best_clk))
+				clk_put(*best_clk);
 			*best_clk = clk;
 			best_quot = quot;
 			*clk_num = cnt;
 			deviation = calc_deviation;
+		} else {
+			clk_put(clk);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/sc16is7xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/sc16is7xx.c
@@ -18,13 +18,14 @@
 #include <linux/module.h>
 #include <linux/property.h>
 #include <linux/regmap.h>
+#include <linux/sched.h>
 #include <linux/serial_core.h>
 #include <linux/serial.h>
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
 #include <linux/spi/spi.h>
 #include <linux/uaccess.h>
-#include <uapi/linux/sched/types.h>
+#include <linux/units.h>
 
 #define SC16IS7XX_NAME			"sc16is7xx"
 #define SC16IS7XX_MAX_DEVS		8
@@ -375,9 +376,7 @@
 	const u8 line = sc16is7xx_line(port);
 	u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line;
 
-	regcache_cache_bypass(s->regmap, true);
-	regmap_raw_read(s->regmap, addr, s->buf, rxlen);
-	regcache_cache_bypass(s->regmap, false);
+	regmap_noinc_read(s->regmap, addr, s->buf, rxlen);
 }
 
 static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send)
@@ -393,9 +392,7 @@
 	if (unlikely(!to_send))
 		return;
 
-	regcache_cache_bypass(s->regmap, true);
-	regmap_raw_write(s->regmap, addr, s->buf, to_send);
-	regcache_cache_bypass(s->regmap, false);
+	regmap_noinc_write(s->regmap, addr, s->buf, to_send);
 }
 
 static void sc16is7xx_port_update(struct uart_port *port, u8 reg,
@@ -488,16 +485,33 @@
 	return false;
 }
 
+static bool sc16is7xx_regmap_noinc(struct device *dev, unsigned int reg)
+{
+	return reg == SC16IS7XX_RHR_REG;
+}
+
+/*
+ * Configure programmable baud rate generator (divisor) according to the
+ * desired baud rate.
+ *
+ * From the datasheet, the divisor is computed according to:
+ *
+ *              XTAL1 input frequency
+ *             -----------------------
+ *                    prescaler
+ * divisor = ---------------------------
+ *            baud-rate x sampling-rate
+ */
 static int sc16is7xx_set_baud(struct uart_port *port, int baud)
 {
 	struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
 	u8 lcr;
-	u8 prescaler = 0;
+	unsigned int prescaler = 1;
 	unsigned long clk = port->uartclk, div = clk / 16 / baud;
 
-	if (div > 0xffff) {
-		prescaler = SC16IS7XX_MCR_CLKSEL_BIT;
-		div /= 4;
+	if (div >= BIT(16)) {
+		prescaler = 4;
+		div /= prescaler;
 	}
 
 	/* In an amazing feat of design, the Enhanced Features Register shares
@@ -532,9 +546,10 @@
 
 	mutex_unlock(&s->efr_lock);
 
+	/* If bit MCR_CLKSEL is set, the divide by 4 prescaler is activated. */
 	sc16is7xx_port_update(port, SC16IS7XX_MCR_REG,
 			      SC16IS7XX_MCR_CLKSEL_BIT,
-			      prescaler);
+			      prescaler == 1 ? 0 : SC16IS7XX_MCR_CLKSEL_BIT);
 
 	/* Open the LCR divisors for configuration */
 	sc16is7xx_port_write(port, SC16IS7XX_LCR_REG,
@@ -549,7 +564,7 @@
 	/* Put LCR back to the normal mode */
 	sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);
 
-	return DIV_ROUND_CLOSEST(clk / 16, div);
+	return DIV_ROUND_CLOSEST((clk / prescaler) / 16, div);
 }
 
 static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen,
@@ -694,6 +709,18 @@
 		case SC16IS7XX_IIR_RTOI_SRC:
 		case SC16IS7XX_IIR_XOFFI_SRC:
 			rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG);
+
+			/*
+			 * There is a silicon bug that makes the chip report a
+			 * time-out interrupt but no data in the FIFO. This is
+			 * described in errata section 18.1.4.
+			 *
+			 * When this happens, read one byte from the FIFO to
+			 * clear the interrupt.
+			 */
+			if (iir == SC16IS7XX_IIR_RTOI_SRC && !rxlen)
+				rxlen = 1;
+
 			if (rxlen)
 				sc16is7xx_handle_rx(port, rxlen, iir);
 			break;
@@ -734,12 +761,15 @@
 static void sc16is7xx_tx_proc(struct kthread_work *ws)
 {
 	struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port);
+	struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
 
 	if ((port->rs485.flags & SER_RS485_ENABLED) &&
 	    (port->rs485.delay_rts_before_send > 0))
 		msleep(port->rs485.delay_rts_before_send);
 
+	mutex_lock(&s->efr_lock);
 	sc16is7xx_handle_tx(port);
+	mutex_unlock(&s->efr_lock);
 }
 
 static void sc16is7xx_reconf_rs485(struct uart_port *port)
@@ -952,7 +982,7 @@
 	uart_update_timeout(port, termios->c_cflag, baud);
 }
 
-static int sc16is7xx_config_rs485(struct uart_port *port,
+static int sc16is7xx_config_rs485(struct uart_port *port, struct ktermios *termios,
 				  struct serial_rs485 *rs485)
 {
 	struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
@@ -1167,9 +1197,18 @@
 		state |= BIT(offset);
 	else
 		state &= ~BIT(offset);
-	sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state);
+
+	/*
+	 * If we write IOSTATE first, and then IODIR, the output value is not
+	 * transferred to the corresponding I/O pin.
+	 * The datasheet states that each register bit will be transferred to
+	 * the corresponding I/O pin programmed as output when writing to
+	 * IOSTATE. Therefore, configure direction first with IODIR, and then
+	 * set value after with IOSTATE.
+	 */
 	sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset),
 			      BIT(offset));
+	sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state);
 
 	return 0;
 }
@@ -1242,25 +1281,6 @@
 	}
 	sched_set_fifo(s->kworker_task);
 
-#ifdef CONFIG_GPIOLIB
-	if (devtype->nr_gpio) {
-		/* Setup GPIO cotroller */
-		s->gpio.owner		 = THIS_MODULE;
-		s->gpio.parent		 = dev;
-		s->gpio.label		 = dev_name(dev);
-		s->gpio.direction_input	 = sc16is7xx_gpio_direction_input;
-		s->gpio.get		 = sc16is7xx_gpio_get;
-		s->gpio.direction_output = sc16is7xx_gpio_direction_output;
-		s->gpio.set		 = sc16is7xx_gpio_set;
-		s->gpio.base		 = -1;
-		s->gpio.ngpio		 = devtype->nr_gpio;
-		s->gpio.can_sleep	 = 1;
-		ret = gpiochip_add_data(&s->gpio, s);
-		if (ret)
-			goto out_thread;
-	}
-#endif
-
 	/* reset device, purging any pending irq / data */
 	regmap_write(s->regmap, SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT,
 			SC16IS7XX_IOCONTROL_SRESET_BIT);
@@ -1274,6 +1294,12 @@
 		s->p[i].port.fifosize	= SC16IS7XX_FIFO_SIZE;
 		s->p[i].port.flags	= UPF_FIXED_TYPE | UPF_LOW_LATENCY;
 		s->p[i].port.iobase	= i;
+		/*
+		 * Use all ones as membase to make sure uart_configure_port() in
+		 * serial_core.c does not abort for SPI/I2C devices where the
+		 * membase address is not applicable.
+		 */
+		s->p[i].port.membase	= (void __iomem *)~0;
 		s->p[i].port.iotype	= UPIO_PORT;
 		s->p[i].port.uartclk	= freq;
 		s->p[i].port.rs485_config = sc16is7xx_config_rs485;
@@ -1326,6 +1352,25 @@
 				s->p[u].irda_mode = true;
 	}
 
+#ifdef CONFIG_GPIOLIB
+	if (devtype->nr_gpio) {
+		/* Setup GPIO cotroller */
+		s->gpio.owner		 = THIS_MODULE;
+		s->gpio.parent		 = dev;
+		s->gpio.label		 = dev_name(dev);
+		s->gpio.direction_input	 = sc16is7xx_gpio_direction_input;
+		s->gpio.get		 = sc16is7xx_gpio_get;
+		s->gpio.direction_output = sc16is7xx_gpio_direction_output;
+		s->gpio.set		 = sc16is7xx_gpio_set;
+		s->gpio.base		 = -1;
+		s->gpio.ngpio		 = devtype->nr_gpio;
+		s->gpio.can_sleep	 = 1;
+		ret = gpiochip_add_data(&s->gpio, s);
+		if (ret)
+			goto out_thread;
+	}
+#endif
+
 	/*
 	 * Setup interrupt. We first try to acquire the IRQ line as level IRQ.
 	 * If that succeeds, we can allow sharing the interrupt as well.
@@ -1345,18 +1390,19 @@
 	if (!ret)
 		return 0;
 
-out_ports:
-	for (i--; i >= 0; i--) {
-		uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port);
-		clear_bit(s->p[i].port.line, &sc16is7xx_lines);
-	}
-
 #ifdef CONFIG_GPIOLIB
 	if (devtype->nr_gpio)
 		gpiochip_remove(&s->gpio);
 
 out_thread:
 #endif
+
+out_ports:
+	for (i--; i >= 0; i--) {
+		uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port);
+		clear_bit(s->p[i].port.line, &sc16is7xx_lines);
+	}
+
 	kthread_stop(s->kworker_task);
 
 out_clk:
@@ -1407,6 +1453,8 @@
 	.cache_type = REGCACHE_RBTREE,
 	.volatile_reg = sc16is7xx_regmap_volatile,
 	.precious_reg = sc16is7xx_regmap_precious,
+	.writeable_noinc_reg = sc16is7xx_regmap_noinc,
+	.readable_noinc_reg = sc16is7xx_regmap_noinc,
 };
 
 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI
@@ -1418,9 +1466,12 @@
 
 	/* Setup SPI bus */
 	spi->bits_per_word	= 8;
-	/* only supports mode 0 on SC16IS762 */
+	/* For all variants, only mode 0 is supported */
+	if ((spi->mode & SPI_MODE_X_MASK) != SPI_MODE_0)
+		return dev_err_probe(&spi->dev, -EINVAL, "Unsupported SPI mode\n");
+
 	spi->mode		= spi->mode ? : SPI_MODE_0;
-	spi->max_speed_hz	= spi->max_speed_hz ? : 15000000;
+	spi->max_speed_hz	= spi->max_speed_hz ? : 4 * HZ_PER_MHZ;
 	ret = spi_setup(spi);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/serial-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/serial-tegra.c
@@ -525,7 +525,7 @@
 	count = tup->tx_bytes_requested - state.residue;
 	async_tx_ack(tup->tx_dma_desc);
 	spin_lock_irqsave(&tup->uport.lock, flags);
-	xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
+	uart_xmit_advance(&tup->uport, count);
 	tup->tx_in_progress = 0;
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(&tup->uport);
@@ -613,18 +613,18 @@
 static void tegra_uart_stop_tx(struct uart_port *u)
 {
 	struct tegra_uart_port *tup = to_tegra_uport(u);
-	struct circ_buf *xmit = &tup->uport.state->xmit;
 	struct dma_tx_state state;
 	unsigned int count;
 
 	if (tup->tx_in_progress != TEGRA_UART_TX_DMA)
 		return;
 
-	dmaengine_terminate_all(tup->tx_dma_chan);
+	dmaengine_pause(tup->tx_dma_chan);
 	dmaengine_tx_status(tup->tx_dma_chan, tup->tx_cookie, &state);
+	dmaengine_terminate_all(tup->tx_dma_chan);
 	count = tup->tx_bytes_requested - state.residue;
 	async_tx_ack(tup->tx_dma_desc);
-	xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
+	uart_xmit_advance(&tup->uport, count);
 	tup->tx_in_progress = 0;
 }
 
@@ -764,8 +764,9 @@
 		return;
 	}
 
-	dmaengine_terminate_all(tup->rx_dma_chan);
+	dmaengine_pause(tup->rx_dma_chan);
 	dmaengine_tx_status(tup->rx_dma_chan, tup->rx_cookie, &state);
+	dmaengine_terminate_all(tup->rx_dma_chan);
 
 	tegra_uart_rx_buffer_push(tup, state.residue);
 	tup->rx_dma_active = false;
@@ -998,7 +999,11 @@
 	tup->ier_shadow = 0;
 	tup->current_baud = 0;
 
-	clk_prepare_enable(tup->uart_clk);
+	ret = clk_prepare_enable(tup->uart_clk);
+	if (ret) {
+		dev_err(tup->uport.dev, "could not enable clk\n");
+		return ret;
+	}
 
 	/* Reset the UART controller to clear all previous status.*/
 	reset_control_assert(tup->rst);
@@ -1046,6 +1051,7 @@
 	if (tup->cdata->fifo_mode_enable_status) {
 		ret = tegra_uart_wait_fifo_mode_enabled(tup);
 		if (ret < 0) {
+			clk_disable_unprepare(tup->uart_clk);
 			dev_err(tup->uport.dev,
 				"Failed to enable FIFO mode: %d\n", ret);
 			return ret;
@@ -1067,6 +1073,7 @@
 	 */
 	ret = tegra_set_baudrate(tup, TEGRA_UART_DEFAULT_BAUD);
 	if (ret < 0) {
+		clk_disable_unprepare(tup->uart_clk);
 		dev_err(tup->uport.dev, "Failed to set baud rate\n");
 		return ret;
 	}
@@ -1226,10 +1233,13 @@
 				dev_name(u->dev), tup);
 	if (ret < 0) {
 		dev_err(u->dev, "Failed to register ISR for IRQ %d\n", u->irq);
-		goto fail_hw_init;
+		goto fail_request_irq;
 	}
 	return 0;
 
+fail_request_irq:
+	/* tup->uart_clk is already enabled in tegra_uart_hw_init */
+	clk_disable_unprepare(tup->uart_clk);
 fail_hw_init:
 	if (!tup->use_rx_pio)
 		tegra_uart_dma_channel_free(tup, true);
@@ -1506,7 +1516,7 @@
 	.fifo_mode_enable_status	= false,
 	.uart_max_port			= 5,
 	.max_dma_burst_bytes		= 4,
-	.error_tolerance_low_range	= 0,
+	.error_tolerance_low_range	= -4,
 	.error_tolerance_high_range	= 4,
 };
 
@@ -1517,7 +1527,7 @@
 	.fifo_mode_enable_status	= false,
 	.uart_max_port			= 5,
 	.max_dma_burst_bytes		= 4,
-	.error_tolerance_low_range	= 0,
+	.error_tolerance_low_range	= -4,
 	.error_tolerance_high_range	= 4,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/serial_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/serial_core.c
@@ -24,6 +24,7 @@
 #include <linux/sysrq.h>
 #include <linux/delay.h>
 #include <linux/mutex.h>
+#include <linux/math64.h>
 #include <linux/security.h>
 
 #include <linux/irq.h>
@@ -42,6 +43,11 @@
 
 #define HIGH_BITS_OFFSET	((sizeof(long)-sizeof(int))*8)
 
+/*
+ * Max time with active RTS before/after data is sent.
+ */
+#define RS485_MAX_RTS_DELAY	100 /* msecs */
+
 static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
 					struct ktermios *old_termios);
 static void uart_wait_until_sent(struct tty_struct *tty, int timeout);
@@ -147,7 +153,7 @@
 	spin_lock_irqsave(&port->lock, flags);
 	old = port->mctrl;
 	port->mctrl = (old & ~clear) | set;
-	if (old != port->mctrl)
+	if (old != port->mctrl && !(port->rs485.flags & SER_RS485_ENABLED))
 		port->ops->set_mctrl(port, port->mctrl);
 	spin_unlock_irqrestore(&port->lock, flags);
 }
@@ -157,23 +163,10 @@
 
 static void uart_port_dtr_rts(struct uart_port *uport, int raise)
 {
-	int rs485_on = uport->rs485_config &&
-		(uport->rs485.flags & SER_RS485_ENABLED);
-	int RTS_after_send = !!(uport->rs485.flags & SER_RS485_RTS_AFTER_SEND);
-
-	if (raise) {
-		if (rs485_on && !RTS_after_send) {
-			uart_set_mctrl(uport, TIOCM_DTR);
-			uart_clear_mctrl(uport, TIOCM_RTS);
-		} else {
-			uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
-		}
-	} else {
-		unsigned int clear = TIOCM_DTR;
-
-		clear |= (!rs485_on || !RTS_after_send) ? TIOCM_RTS : 0;
-		uart_clear_mctrl(uport, clear);
-	}
+	if (raise)
+		uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
+	else
+		uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
 }
 
 /*
@@ -222,7 +215,11 @@
 	if (retval == 0) {
 		if (uart_console(uport) && uport->cons->cflag) {
 			tty->termios.c_cflag = uport->cons->cflag;
+			tty->termios.c_ispeed = uport->cons->ispeed;
+			tty->termios.c_ospeed = uport->cons->ospeed;
 			uport->cons->cflag = 0;
+			uport->cons->ispeed = 0;
+			uport->cons->ospeed = 0;
 		}
 		/*
 		 * Initialise the hardware port settings.
@@ -290,11 +287,16 @@
 		/*
 		 * Turn off DTR and RTS early.
 		 */
-		if (uport && uart_console(uport) && tty)
-			uport->cons->cflag = tty->termios.c_cflag;
+		if (uport) {
+			if (uart_console(uport) && tty) {
+				uport->cons->cflag = tty->termios.c_cflag;
+				uport->cons->ispeed = tty->termios.c_ispeed;
+				uport->cons->ospeed = tty->termios.c_ospeed;
+			}
 
-		if (!tty || C_HUPCL(tty))
-			uart_port_dtr_rts(uport, 0);
+			if (!tty || C_HUPCL(tty))
+				uart_port_dtr_rts(uport, 0);
+		}
 
 		uart_port_shutdown(port);
 	}
@@ -334,15 +336,18 @@
 uart_update_timeout(struct uart_port *port, unsigned int cflag,
 		    unsigned int baud)
 {
-	unsigned int size;
+	unsigned int size = tty_get_frame_size(cflag);
+	u64 frame_time;
 
-	size = tty_get_frame_size(cflag) * port->fifosize;
+	frame_time = (u64)size * NSEC_PER_SEC;
+	size *= port->fifosize;
 
 	/*
 	 * Figure the timeout to send the above number of bits.
 	 * Add .02 seconds of slop
 	 */
 	port->timeout = (HZ * size) / baud + HZ/50;
+	port->frame_time = DIV64_U64_ROUND_UP(frame_time, baud);
 }
 
 EXPORT_SYMBOL(uart_update_timeout);
@@ -646,6 +651,20 @@
 }
 
 /*
+ * This function performs low-level write of high-priority XON/XOFF
+ * character and accounting for it.
+ *
+ * Requires uart_port to implement .serial_out().
+ */
+void uart_xchar_out(struct uart_port *uport, int offset)
+{
+	serial_port_out(uport, offset, uport->x_char);
+	uport->icount.tx++;
+	uport->x_char = 0;
+}
+EXPORT_SYMBOL_GPL(uart_xchar_out);
+
+/*
  * This function is used to send a high-priority XON/XOFF character to
  * the device
  */
@@ -823,6 +842,14 @@
 	new_flags = (__force upf_t)new_info->flags;
 	old_custom_divisor = uport->custom_divisor;
 
+	if (!(uport->flags & UPF_FIXED_PORT)) {
+		unsigned int uartclk = new_info->baud_base * 16;
+		/* check needs to be done here before other settings made */
+		if (uartclk == 0) {
+			retval = -EINVAL;
+			goto exit;
+		}
+	}
 	if (!capable(CAP_SYS_ADMIN)) {
 		retval = -EPERM;
 		if (change_irq || change_port ||
@@ -1273,7 +1300,7 @@
 	return 0;
 }
 
-static int uart_set_rs485_config(struct uart_port *port,
+static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
 			 struct serial_rs485 __user *rs485_user)
 {
 	struct serial_rs485 rs485;
@@ -1286,8 +1313,41 @@
 	if (copy_from_user(&rs485, rs485_user, sizeof(*rs485_user)))
 		return -EFAULT;
 
+	/* pick sane settings if the user hasn't */
+	if (!(rs485.flags & SER_RS485_RTS_ON_SEND) ==
+	    !(rs485.flags & SER_RS485_RTS_AFTER_SEND)) {
+		dev_warn_ratelimited(port->dev,
+			"%s (%d): invalid RTS setting, using RTS_ON_SEND instead\n",
+			port->name, port->line);
+		rs485.flags |= SER_RS485_RTS_ON_SEND;
+		rs485.flags &= ~SER_RS485_RTS_AFTER_SEND;
+	}
+
+	if (rs485.delay_rts_before_send > RS485_MAX_RTS_DELAY) {
+		rs485.delay_rts_before_send = RS485_MAX_RTS_DELAY;
+		dev_warn_ratelimited(port->dev,
+			"%s (%d): RTS delay before sending clamped to %u ms\n",
+			port->name, port->line, rs485.delay_rts_before_send);
+	}
+
+	if (rs485.delay_rts_after_send > RS485_MAX_RTS_DELAY) {
+		rs485.delay_rts_after_send = RS485_MAX_RTS_DELAY;
+		dev_warn_ratelimited(port->dev,
+			"%s (%d): RTS delay after sending clamped to %u ms\n",
+			port->name, port->line, rs485.delay_rts_after_send);
+	}
+	/* Return clean padding area to userspace */
+	memset(rs485.padding, 0, sizeof(rs485.padding));
+
 	spin_lock_irqsave(&port->lock, flags);
-	ret = port->rs485_config(port, &rs485);
+	ret = port->rs485_config(port, &tty->termios, &rs485);
+	if (!ret) {
+		port->rs485 = rs485;
+
+		/* Reset RTS and other mctrl lines when disabling RS485 */
+		if (!(rs485.flags & SER_RS485_ENABLED))
+			port->ops->set_mctrl(port, port->mctrl);
+	}
 	spin_unlock_irqrestore(&port->lock, flags);
 	if (ret)
 		return ret;
@@ -1394,6 +1454,10 @@
 	if (ret != -ENOIOCTLCMD)
 		goto out;
 
+	/* rs485_config requires more locking than others */
+	if (cmd == TIOCSRS485)
+		down_write(&tty->termios_rwsem);
+
 	mutex_lock(&port->mutex);
 	uport = uart_port_check(state);
 
@@ -1417,7 +1481,7 @@
 		break;
 
 	case TIOCSRS485:
-		ret = uart_set_rs485_config(uport, uarg);
+		ret = uart_set_rs485_config(tty, uport, uarg);
 		break;
 
 	case TIOCSISO7816:
@@ -1434,6 +1498,8 @@
 	}
 out_up:
 	mutex_unlock(&port->mutex);
+	if (cmd == TIOCSRS485)
+		up_write(&tty->termios_rwsem);
 out:
 	return ret;
 }
@@ -1542,6 +1608,7 @@
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
 	struct uart_port *uport = uart_port_check(state);
+	char *buf;
 
 	/*
 	 * At this point, we stop accepting input.  To do this, we
@@ -1563,8 +1630,18 @@
 	 */
 	tty_port_set_suspended(port, 0);
 
-	uart_change_pm(state, UART_PM_STATE_OFF);
+	/*
+	 * Free the transmit buffer.
+	 */
+	spin_lock_irq(&uport->lock);
+	buf = state->xmit.buf;
+	state->xmit.buf = NULL;
+	spin_unlock_irq(&uport->lock);
+
+	if (buf)
+		free_page((unsigned long)buf);
 
+	uart_change_pm(state, UART_PM_STATE_OFF);
 }
 
 static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
@@ -1590,10 +1667,8 @@
 	 * Note: we have to use pretty tight timings here to satisfy
 	 * the NIST-PCTS.
 	 */
-	char_time = (port->timeout - HZ/50) / port->fifosize;
-	char_time = char_time / 5;
-	if (char_time == 0)
-		char_time = 1;
+	char_time = max(nsecs_to_jiffies(port->frame_time / 5), 1UL);
+
 	if (timeout && timeout < char_time)
 		char_time = timeout;
 
@@ -1888,11 +1963,6 @@
 }
 #endif
 
-static inline bool uart_console_enabled(struct uart_port *port)
-{
-	return uart_console(port) && (port->cons->flags & CON_ENABLED);
-}
-
 static void uart_port_spin_lock_init(struct uart_port *port)
 {
 	spin_lock_init(&port->lock);
@@ -2094,8 +2164,11 @@
 	 * Allow the setting of the UART parameters with a NULL console
 	 * too:
 	 */
-	if (co)
+	if (co) {
 		co->cflag = termios.c_cflag;
+		co->ispeed = termios.c_ispeed;
+		co->ospeed = termios.c_ospeed;
+	}
 
 	return 0;
 }
@@ -2170,7 +2243,8 @@
 
 		spin_lock_irq(&uport->lock);
 		ops->stop_tx(uport);
-		ops->set_mctrl(uport, 0);
+		if (!(uport->rs485.flags & SER_RS485_ENABLED))
+			ops->set_mctrl(uport, 0);
 		ops->stop_rx(uport);
 		spin_unlock_irq(&uport->lock);
 
@@ -2229,6 +2303,8 @@
 		 */
 		memset(&termios, 0, sizeof(struct ktermios));
 		termios.c_cflag = uport->cons->cflag;
+		termios.c_ispeed = uport->cons->ispeed;
+		termios.c_ospeed = uport->cons->ospeed;
 
 		/*
 		 * If that's unset, use the tty termios setting.
@@ -2249,7 +2325,8 @@
 
 		uart_change_pm(state, UART_PM_STATE_ON);
 		spin_lock_irq(&uport->lock);
-		ops->set_mctrl(uport, 0);
+		if (!(uport->rs485.flags & SER_RS485_ENABLED))
+			ops->set_mctrl(uport, 0);
 		spin_unlock_irq(&uport->lock);
 		if (console_suspend_enabled || !uart_console(uport)) {
 			/* Protected by port mutex for now */
@@ -2260,7 +2337,10 @@
 				if (tty)
 					uart_change_speed(tty, state, NULL);
 				spin_lock_irq(&uport->lock);
-				ops->set_mctrl(uport, uport->mctrl);
+				if (!(uport->rs485.flags & SER_RS485_ENABLED))
+					ops->set_mctrl(uport, uport->mctrl);
+				else
+					uport->rs485_config(uport, NULL, &uport->rs485);
 				ops->start_tx(uport);
 				spin_unlock_irq(&uport->lock);
 				tty_port_set_initialized(port, 1);
@@ -2348,7 +2428,12 @@
 			port->type = PORT_UNKNOWN;
 			flags |= UART_CONFIG_TYPE;
 		}
+		/* Synchronize with possible boot console. */
+		if (uart_console(port))
+			console_lock();
 		port->ops->config_port(port, flags);
+		if (uart_console(port))
+			console_unlock();
 	}
 
 	if (port->type != PORT_UNKNOWN) {
@@ -2356,6 +2441,10 @@
 
 		uart_report_port(drv, port);
 
+		/* Synchronize with possible boot console. */
+		if (uart_console(port))
+			console_lock();
+
 		/* Power up port for set_mctrl() */
 		uart_change_pm(state, UART_PM_STATE_ON);
 
@@ -2365,9 +2454,16 @@
 		 * We probably don't need a spinlock around this, but
 		 */
 		spin_lock_irqsave(&port->lock, flags);
-		port->ops->set_mctrl(port, port->mctrl & TIOCM_DTR);
+		port->mctrl &= TIOCM_DTR;
+		if (!(port->rs485.flags & SER_RS485_ENABLED))
+			port->ops->set_mctrl(port, port->mctrl);
+		else
+			port->rs485_config(port, NULL, &port->rs485);
 		spin_unlock_irqrestore(&port->lock, flags);
 
+		if (uart_console(port))
+			console_unlock();
+
 		/*
 		 * If this driver supports console, and it hasn't been
 		 * successfully registered yet, try to re-register it.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/serial_txx9.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/serial_txx9.c
@@ -644,6 +644,8 @@
 	case CS6:	/* not supported */
 	case CS8:
 		cval |= TXX9_SILCR_UMODE_8BIT;
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
 		break;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/sh-sci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/sh-sci.c
@@ -31,6 +31,7 @@
 #include <linux/ioport.h>
 #include <linux/ktime.h>
 #include <linux/major.h>
+#include <linux/minmax.h>
 #include <linux/module.h>
 #include <linux/mm.h>
 #include <linux/of.h>
@@ -163,6 +164,7 @@
 static struct sci_port sci_ports[SCI_NPORTS];
 static unsigned long sci_ports_in_use;
 static struct uart_driver sci_uart_driver;
+static bool sci_uart_earlycon;
 
 static inline struct sci_port *
 to_sci_port(struct uart_port *uart)
@@ -1254,9 +1256,14 @@
 static void sci_dma_rx_release(struct sci_port *s)
 {
 	struct dma_chan *chan = s->chan_rx_saved;
+	struct uart_port *port = &s->port;
+	unsigned long flags;
 
+	uart_port_lock_irqsave(port, &flags);
 	s->chan_rx_saved = NULL;
 	sci_dma_rx_chan_invalidate(s);
+	uart_port_unlock_irqrestore(port, flags);
+
 	dmaengine_terminate_sync(chan);
 	dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0],
 			  sg_dma_address(&s->sg_rx[0]));
@@ -2390,8 +2397,12 @@
 	int best_clk = -1;
 	unsigned long flags;
 
-	if ((termios->c_cflag & CSIZE) == CS7)
+	if ((termios->c_cflag & CSIZE) == CS7) {
 		smr_val |= SCSMR_CHR;
+	} else {
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
+	}
 	if (termios->c_cflag & PARENB)
 		smr_val |= SCSMR_PE;
 	if (termios->c_cflag & PARODD)
@@ -2891,6 +2902,13 @@
 			sci_port->irqs[i] = platform_get_irq(dev, i);
 	}
 
+	/*
+	 * The fourth interrupt on SCI port is transmit end interrupt, so
+	 * shuffle the interrupts.
+	 */
+	if (p->type == PORT_SCI)
+		swap(sci_port->irqs[SCIx_BRI_IRQ], sci_port->irqs[SCIx_TEI_IRQ]);
+
 	/* The SCI generates several interrupts. They can be muxed together or
 	 * connected to different interrupt lines. In the muxed case only one
 	 * interrupt resource is specified as there is only one interrupt ID.
@@ -2956,7 +2974,7 @@
 	port->flags		= UPF_FIXED_PORT | UPF_BOOT_AUTOCONF | p->flags;
 	port->fifosize		= sci_port->params->fifosize;
 
-	if (port->type == PORT_SCI) {
+	if (port->type == PORT_SCI && !dev->dev.of_node) {
 		if (sci_port->reg_size >= 0x20)
 			port->regshift = 2;
 		else
@@ -3302,6 +3320,7 @@
 static int sci_probe(struct platform_device *dev)
 {
 	struct plat_sci_port *p;
+	struct resource *res;
 	struct sci_port *sp;
 	unsigned int dev_id;
 	int ret;
@@ -3331,6 +3350,26 @@
 	}
 
 	sp = &sci_ports[dev_id];
+
+	/*
+	 * In case:
+	 * - the probed port alias is zero (as the one used by earlycon), and
+	 * - the earlycon is still active (e.g., "earlycon keep_bootcon" in
+	 *   bootargs)
+	 *
+	 * defer the probe of this serial. This is a debug scenario and the user
+	 * must be aware of it.
+	 *
+	 * Except when the probed port is the same as the earlycon port.
+	 */
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+
+	if (sci_uart_earlycon && sp == &sci_ports[0] && sp->port.mapbase != res->start)
+		return dev_err_probe(&dev->dev, -EBUSY, "sci_port[0] is used by earlycon!\n");
+
 	platform_set_drvdata(dev, sp);
 
 	ret = sci_probe_single(dev, dev_id, p, sp);
@@ -3414,7 +3453,7 @@
 			   early_serial_buf, ARRAY_SIZE(early_serial_buf));
 #endif
 #ifdef CONFIG_SERIAL_SH_SCI_EARLYCON
-static struct plat_sci_port port_cfg __initdata;
+static struct plat_sci_port port_cfg;
 
 static int __init early_console_setup(struct earlycon_device *device,
 				      int type)
@@ -3429,6 +3468,7 @@
 	port_cfg.type = type;
 	sci_ports[0].cfg = &port_cfg;
 	sci_ports[0].params = sci_probe_regmap(&port_cfg);
+	sci_uart_earlycon = true;
 	port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR);
 	sci_serial_out(&sci_ports[0].port, SCSCR,
 		       SCSCR_RE | SCSCR_TE | port_cfg.scscr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/sifive.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/sifive.c
@@ -666,12 +666,16 @@
 	int rate;
 	char nstop;
 
-	if ((termios->c_cflag & CSIZE) != CS8)
+	if ((termios->c_cflag & CSIZE) != CS8) {
 		dev_err_once(ssp->port.dev, "only 8-bit words supported\n");
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
+	}
 	if (termios->c_iflag & (INPCK | PARMRK))
 		dev_err_once(ssp->port.dev, "parity checking not supported\n");
 	if (termios->c_iflag & BRKINT)
 		dev_err_once(ssp->port.dev, "BREAK detection not supported\n");
+	termios->c_iflag &= ~(INPCK|PARMRK|BRKINT);
 
 	/* Set number of stop bits */
 	nstop = (termios->c_cflag & CSTOPB) ? 2 : 1;
@@ -839,7 +843,7 @@
 	local_irq_restore(flags);
 }
 
-static int __init sifive_serial_console_setup(struct console *co, char *options)
+static int sifive_serial_console_setup(struct console *co, char *options)
 {
 	struct sifive_serial_port *ssp;
 	int baud = SIFIVE_DEFAULT_BAUD_RATE;
@@ -998,7 +1002,7 @@
 	/* Set up clock divider */
 	ssp->clkin_rate = clk_get_rate(ssp->clk);
 	ssp->baud_rate = SIFIVE_DEFAULT_BAUD_RATE;
-	ssp->port.uartclk = ssp->baud_rate * 16;
+	ssp->port.uartclk = ssp->clkin_rate;
 	__ssp_update_div(ssp);
 
 	platform_set_drvdata(pdev, ssp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/sprd_serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/sprd_serial.c
@@ -367,7 +367,7 @@
 	if (sp->rx_dma.virt)
 		dma_free_coherent(sp->port.dev, SPRD_UART_RX_SIZE,
 				  sp->rx_dma.virt, sp->rx_dma.phys_addr);
-
+	sp->rx_dma.virt = NULL;
 }
 
 static int sprd_rx_dma_config(struct uart_port *port, u32 burst)
@@ -1133,7 +1133,7 @@
 static int sprd_clk_init(struct uart_port *uport)
 {
 	struct clk *clk_uart, *clk_parent;
-	struct sprd_uart_port *u = sprd_port[uport->line];
+	struct sprd_uart_port *u = container_of(uport, struct sprd_uart_port, port);
 
 	clk_uart = devm_clk_get(uport->dev, "uart");
 	if (IS_ERR(clk_uart)) {
@@ -1176,22 +1176,22 @@
 {
 	struct resource *res;
 	struct uart_port *up;
+	struct sprd_uart_port *sport;
 	int irq;
 	int index;
 	int ret;
 
 	index = of_alias_get_id(pdev->dev.of_node, "serial");
-	if (index < 0 || index >= ARRAY_SIZE(sprd_port)) {
+	if (index < 0 || index >= UART_NR_MAX) {
 		dev_err(&pdev->dev, "got a wrong serial alias id %d\n", index);
 		return -EINVAL;
 	}
 
-	sprd_port[index] = devm_kzalloc(&pdev->dev, sizeof(*sprd_port[index]),
-					GFP_KERNEL);
-	if (!sprd_port[index])
+	sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
+	if (!sport)
 		return -ENOMEM;
 
-	up = &sprd_port[index]->port;
+	up = &sport->port;
 	up->dev = &pdev->dev;
 	up->line = index;
 	up->type = PORT_SPRD;
@@ -1222,7 +1222,7 @@
 	 * Allocate one dma buffer to prepare for receive transfer, in case
 	 * memory allocation failure at runtime.
 	 */
-	ret = sprd_rx_alloc_buf(sprd_port[index]);
+	ret = sprd_rx_alloc_buf(sport);
 	if (ret)
 		return ret;
 
@@ -1230,17 +1230,27 @@
 		ret = uart_register_driver(&sprd_uart_driver);
 		if (ret < 0) {
 			pr_err("Failed to register SPRD-UART driver\n");
-			return ret;
+			goto free_rx_buf;
 		}
 	}
+
 	sprd_ports_num++;
+	sprd_port[index] = sport;
 
 	ret = uart_add_one_port(&sprd_uart_driver, up);
 	if (ret)
-		sprd_remove(pdev);
+		goto clean_port;
 
 	platform_set_drvdata(pdev, up);
 
+	return 0;
+
+clean_port:
+	sprd_port[index] = NULL;
+	if (--sprd_ports_num == 0)
+		uart_unregister_driver(&sprd_uart_driver);
+free_rx_buf:
+	sprd_rx_free_buf(sport);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/st-asc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/st-asc.c
@@ -535,10 +535,14 @@
 	/* set character length */
 	if ((cflag & CSIZE) == CS7) {
 		ctrl_val |= ASC_CTL_MODE_7BIT_PAR;
+		cflag |= PARENB;
 	} else {
 		ctrl_val |= (cflag & PARENB) ?  ASC_CTL_MODE_8BIT_PAR :
 						ASC_CTL_MODE_8BIT;
+		cflag &= ~CSIZE;
+		cflag |= CS8;
 	}
+	termios->c_cflag = cflag;
 
 	/* set stop bit */
 	ctrl_val |= (cflag & CSTOPB) ? ASC_CTL_STOP_2BIT : ASC_CTL_STOP_1BIT;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/stm32-usart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/stm32-usart.c
@@ -61,6 +61,53 @@
 	writel_relaxed(val, port->membase + reg);
 }
 
+static unsigned int stm32_usart_tx_empty(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
+
+	if (readl_relaxed(port->membase + ofs->isr) & USART_SR_TC)
+		return TIOCSER_TEMT;
+
+	return 0;
+}
+
+static void stm32_usart_rs485_rts_enable(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	struct serial_rs485 *rs485conf = &port->rs485;
+
+	if (stm32_port->hw_flow_control ||
+	    !(rs485conf->flags & SER_RS485_ENABLED))
+		return;
+
+	if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
+		mctrl_gpio_set(stm32_port->gpios,
+			       stm32_port->port.mctrl | TIOCM_RTS);
+	} else {
+		mctrl_gpio_set(stm32_port->gpios,
+			       stm32_port->port.mctrl & ~TIOCM_RTS);
+	}
+}
+
+static void stm32_usart_rs485_rts_disable(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	struct serial_rs485 *rs485conf = &port->rs485;
+
+	if (stm32_port->hw_flow_control ||
+	    !(rs485conf->flags & SER_RS485_ENABLED))
+		return;
+
+	if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
+		mctrl_gpio_set(stm32_port->gpios,
+			       stm32_port->port.mctrl & ~TIOCM_RTS);
+	} else {
+		mctrl_gpio_set(stm32_port->gpios,
+			       stm32_port->port.mctrl | TIOCM_RTS);
+	}
+}
+
 static void stm32_usart_config_reg_rs485(u32 *cr1, u32 *cr3, u32 delay_ADE,
 					 u32 delay_DDE, u32 baud)
 {
@@ -71,6 +118,8 @@
 	*cr3 |= USART_CR3_DEM;
 	over8 = *cr1 & USART_CR1_OVER8;
 
+	*cr1 &= ~(USART_CR1_DEDT_MASK | USART_CR1_DEAT_MASK);
+
 	if (over8)
 		rs485_deat_dedt = delay_ADE * baud * 8;
 	else
@@ -96,7 +145,7 @@
 	*cr1 |= rs485_deat_dedt;
 }
 
-static int stm32_usart_config_rs485(struct uart_port *port,
+static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *termios,
 				    struct serial_rs485 *rs485conf)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
@@ -147,6 +196,12 @@
 
 	stm32_usart_set_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
 
+	/* Adjust RTS polarity in case it's driven in software */
+	if (stm32_usart_tx_empty(port))
+		stm32_usart_rs485_rts_disable(port);
+	else
+		stm32_usart_rs485_rts_enable(port);
+
 	return 0;
 }
 
@@ -165,63 +220,60 @@
 	return uart_get_rs485_mode(port);
 }
 
-static int stm32_usart_pending_rx(struct uart_port *port, u32 *sr,
-				  int *last_res, bool threaded)
+static bool stm32_usart_rx_dma_enabled(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
+
+	if (!stm32_port->rx_ch)
+		return false;
+
+	return !!(readl_relaxed(port->membase + ofs->cr3) & USART_CR3_DMAR);
+}
+
+/* Return true when data is pending (in pio mode), and false when no data is pending. */
+static bool stm32_usart_pending_rx_pio(struct uart_port *port, u32 *sr)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
-	enum dma_status status;
-	struct dma_tx_state state;
 
 	*sr = readl_relaxed(port->membase + ofs->isr);
+	/* Get pending characters in RDR or FIFO */
+	if (*sr & USART_SR_RXNE) {
+		/* Get all pending characters from the RDR or the FIFO when using interrupts */
+		if (!stm32_usart_rx_dma_enabled(port))
+			return true;
 
-	if (threaded && stm32_port->rx_ch) {
-		status = dmaengine_tx_status(stm32_port->rx_ch,
-					     stm32_port->rx_ch->cookie,
-					     &state);
-		if (status == DMA_IN_PROGRESS && (*last_res != state.residue))
-			return 1;
-		else
-			return 0;
-	} else if (*sr & USART_SR_RXNE) {
-		return 1;
+		/* Handle only RX data errors when using DMA */
+		if (*sr & USART_SR_ERR_MASK)
+			return true;
 	}
-	return 0;
+
+	return false;
 }
 
-static unsigned long stm32_usart_get_char(struct uart_port *port, u32 *sr,
-					  int *last_res)
+static unsigned long stm32_usart_get_char_pio(struct uart_port *port)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	unsigned long c;
 
-	if (stm32_port->rx_ch) {
-		c = stm32_port->rx_buf[RX_BUF_L - (*last_res)--];
-		if ((*last_res) == 0)
-			*last_res = RX_BUF_L;
-	} else {
-		c = readl_relaxed(port->membase + ofs->rdr);
-		/* apply RDR data mask */
-		c &= stm32_port->rdr_mask;
-	}
+	c = readl_relaxed(port->membase + ofs->rdr);
+	/* Apply RDR data mask */
+	c &= stm32_port->rdr_mask;
 
 	return c;
 }
 
-static void stm32_usart_receive_chars(struct uart_port *port, bool threaded)
+static void stm32_usart_receive_chars_pio(struct uart_port *port)
 {
-	struct tty_port *tport = &port->state->port;
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	unsigned long c;
 	u32 sr;
 	char flag;
 
-	spin_lock(&port->lock);
-
-	while (stm32_usart_pending_rx(port, &sr, &stm32_port->last_res,
-				      threaded)) {
+	while (stm32_usart_pending_rx_pio(port, &sr)) {
 		sr |= USART_SR_DUMMY_RX;
 		flag = TTY_NORMAL;
 
@@ -240,7 +292,7 @@
 			writel_relaxed(sr & USART_SR_ERR_MASK,
 				       port->membase + ofs->icr);
 
-		c = stm32_usart_get_char(port, &sr, &stm32_port->last_res);
+		c = stm32_usart_get_char_pio(port);
 		port->icount.rx++;
 		if (sr & USART_SR_ERR_MASK) {
 			if (sr & USART_SR_ORE) {
@@ -274,8 +326,99 @@
 			continue;
 		uart_insert_char(port, sr, USART_SR_ORE, c, flag);
 	}
+}
+
+static void stm32_usart_push_buffer_dma(struct uart_port *port, unsigned int dma_size)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	struct tty_port *ttyport = &stm32_port->port.state->port;
+	unsigned char *dma_start;
+	int dma_count, i;
+
+	dma_start = stm32_port->rx_buf + (RX_BUF_L - stm32_port->last_res);
+
+	/*
+	 * Apply rdr_mask on buffer in order to mask parity bit.
+	 * This loop is useless in cs8 mode because DMA copies only
+	 * 8 bits and already ignores parity bit.
+	 */
+	if (!(stm32_port->rdr_mask == (BIT(8) - 1)))
+		for (i = 0; i < dma_size; i++)
+			*(dma_start + i) &= stm32_port->rdr_mask;
+
+	dma_count = tty_insert_flip_string(ttyport, dma_start, dma_size);
+	port->icount.rx += dma_count;
+	if (dma_count != dma_size)
+		port->icount.buf_overrun++;
+	stm32_port->last_res -= dma_count;
+	if (stm32_port->last_res == 0)
+		stm32_port->last_res = RX_BUF_L;
+}
+
+static void stm32_usart_receive_chars_dma(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	unsigned int dma_size;
+
+	/* DMA buffer is configured in cyclic mode and handles the rollback of the buffer. */
+	if (stm32_port->rx_dma_state.residue > stm32_port->last_res) {
+		/* Conditional first part: from last_res to end of DMA buffer */
+		dma_size = stm32_port->last_res;
+		stm32_usart_push_buffer_dma(port, dma_size);
+	}
+
+	dma_size = stm32_port->last_res - stm32_port->rx_dma_state.residue;
+	stm32_usart_push_buffer_dma(port, dma_size);
+}
+
+static void stm32_usart_receive_chars(struct uart_port *port, bool irqflag)
+{
+	struct tty_port *tport = &port->state->port;
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
+	enum dma_status rx_dma_status;
+	unsigned long flags;
+	u32 sr;
+
+	if (irqflag)
+		spin_lock_irqsave(&port->lock, flags);
+	else
+		spin_lock(&port->lock);
+
+	if (stm32_usart_rx_dma_enabled(port)) {
+		rx_dma_status = dmaengine_tx_status(stm32_port->rx_ch,
+						    stm32_port->rx_ch->cookie,
+						    &stm32_port->rx_dma_state);
+		if (rx_dma_status == DMA_IN_PROGRESS) {
+			/* Empty DMA buffer */
+			stm32_usart_receive_chars_dma(port);
+			sr = readl_relaxed(port->membase + ofs->isr);
+			if (sr & USART_SR_ERR_MASK) {
+				/* Disable DMA request line */
+				stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAR);
+
+				/* Switch to PIO mode to handle the errors */
+				stm32_usart_receive_chars_pio(port);
+
+				/* Switch back to DMA mode */
+				stm32_usart_set_bits(port, ofs->cr3, USART_CR3_DMAR);
+			}
+		} else {
+			/* Disable RX DMA */
+			dmaengine_terminate_async(stm32_port->rx_ch);
+			stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAR);
+			/* Fall back to interrupt mode */
+			dev_dbg(port->dev, "DMA error, fallback to irq mode\n");
+			stm32_usart_receive_chars_pio(port);
+		}
+	} else {
+		stm32_usart_receive_chars_pio(port);
+	}
 
-	uart_unlock_and_check_sysrq(port);
+	if (irqflag)
+		uart_unlock_and_check_sysrq_irqrestore(port, irqflag);
+	else
+		uart_unlock_and_check_sysrq(port);
 
 	tty_flip_buffer_push(tport);
 }
@@ -312,6 +455,21 @@
 		stm32_usart_set_bits(port, ofs->cr1, USART_CR1_TXEIE);
 }
 
+static void stm32_usart_rx_dma_complete(void *arg)
+{
+	struct uart_port *port = arg;
+
+	stm32_usart_receive_chars(port, true);
+}
+
+static void stm32_usart_tc_interrupt_enable(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
+
+	stm32_usart_set_bits(port, ofs->cr1, USART_CR1_TCIE);
+}
+
 static void stm32_usart_tx_interrupt_disable(struct uart_port *port)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
@@ -323,6 +481,14 @@
 		stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_TXEIE);
 }
 
+static void stm32_usart_tc_interrupt_disable(struct uart_port *port)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
+
+	stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_TCIE);
+}
+
 static void stm32_usart_transmit_chars_pio(struct uart_port *port)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
@@ -421,10 +587,30 @@
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	struct circ_buf *xmit = &port->state->xmit;
+	u32 isr;
+	int ret;
+
+	if (!stm32_port->hw_flow_control &&
+	    port->rs485.flags & SER_RS485_ENABLED &&
+	    (port->x_char ||
+	     !(uart_circ_empty(xmit) || uart_tx_stopped(port)))) {
+		stm32_usart_tc_interrupt_disable(port);
+		stm32_usart_rs485_rts_enable(port);
+	}
 
 	if (port->x_char) {
 		if (stm32_port->tx_dma_busy)
 			stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAT);
+
+		/* Check that TDR is empty before filling FIFO */
+		ret =
+		readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr,
+						  isr,
+						  (isr & USART_SR_TXE),
+						  10, 1000);
+		if (ret)
+			dev_warn(port->dev, "1 character may be erased\n");
+
 		writel_relaxed(port->x_char, port->membase + ofs->tdr);
 		port->x_char = 0;
 		port->icount.tx++;
@@ -451,8 +637,14 @@
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(port);
 
-	if (uart_circ_empty(xmit))
+	if (uart_circ_empty(xmit)) {
 		stm32_usart_tx_interrupt_disable(port);
+		if (!stm32_port->hw_flow_control &&
+		    port->rs485.flags & SER_RS485_ENABLED) {
+			stm32_port->txdone = true;
+			stm32_usart_tc_interrupt_enable(port);
+		}
+	}
 }
 
 static irqreturn_t stm32_usart_interrupt(int irq, void *ptr)
@@ -465,6 +657,13 @@
 
 	sr = readl_relaxed(port->membase + ofs->isr);
 
+	if (!stm32_port->hw_flow_control &&
+	    port->rs485.flags & SER_RS485_ENABLED &&
+	    (sr & USART_SR_TC)) {
+		stm32_usart_tc_interrupt_disable(port);
+		stm32_usart_rs485_rts_disable(port);
+	}
+
 	if ((sr & USART_SR_RTOF) && ofs->icr != UNDEF_REG)
 		writel_relaxed(USART_ICR_RTOCF,
 			       port->membase + ofs->icr);
@@ -478,7 +677,12 @@
 			pm_wakeup_event(tport->tty->dev, 0);
 	}
 
-	if ((sr & USART_SR_RXNE) && !(stm32_port->rx_ch))
+	/*
+	 * rx errors in dma mode has to be handled ASAP to avoid overrun as the DMA request
+	 * line has been masked by HW and rx data are stacking in FIFO.
+	 */
+	if (((sr & USART_SR_RXNE) && !stm32_usart_rx_dma_enabled(port)) ||
+	    ((sr & USART_SR_ERR_MASK) && stm32_usart_rx_dma_enabled(port)))
 		stm32_usart_receive_chars(port, false);
 
 	if ((sr & USART_SR_TXE) && !(stm32_port->tx_ch)) {
@@ -487,7 +691,7 @@
 		spin_unlock(&port->lock);
 	}
 
-	if (stm32_port->rx_ch)
+	if (stm32_usart_rx_dma_enabled(port))
 		return IRQ_WAKE_THREAD;
 	else
 		return IRQ_HANDLED;
@@ -496,25 +700,13 @@
 static irqreturn_t stm32_usart_threaded_interrupt(int irq, void *ptr)
 {
 	struct uart_port *port = ptr;
-	struct stm32_port *stm32_port = to_stm32_port(port);
 
-	if (stm32_port->rx_ch)
-		stm32_usart_receive_chars(port, true);
+	/* Receiver timeout irq for DMA RX */
+	stm32_usart_receive_chars(port, false);
 
 	return IRQ_HANDLED;
 }
 
-static unsigned int stm32_usart_tx_empty(struct uart_port *port)
-{
-	struct stm32_port *stm32_port = to_stm32_port(port);
-	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
-
-	if (readl_relaxed(port->membase + ofs->isr) & USART_SR_TC)
-		return TIOCSER_TEMT;
-
-	return 0;
-}
-
 static void stm32_usart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
@@ -552,42 +744,23 @@
 /* Transmit stop */
 static void stm32_usart_stop_tx(struct uart_port *port)
 {
-	struct stm32_port *stm32_port = to_stm32_port(port);
-	struct serial_rs485 *rs485conf = &port->rs485;
-
 	stm32_usart_tx_interrupt_disable(port);
 
-	if (rs485conf->flags & SER_RS485_ENABLED) {
-		if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
-			mctrl_gpio_set(stm32_port->gpios,
-					stm32_port->port.mctrl & ~TIOCM_RTS);
-		} else {
-			mctrl_gpio_set(stm32_port->gpios,
-					stm32_port->port.mctrl | TIOCM_RTS);
-		}
-	}
+	stm32_usart_rs485_rts_disable(port);
 }
 
 /* There are probably characters waiting to be transmitted. */
 static void stm32_usart_start_tx(struct uart_port *port)
 {
-	struct stm32_port *stm32_port = to_stm32_port(port);
-	struct serial_rs485 *rs485conf = &port->rs485;
 	struct circ_buf *xmit = &port->state->xmit;
 
-	if (uart_circ_empty(xmit))
+	if (uart_circ_empty(xmit) && !port->x_char) {
+		stm32_usart_rs485_rts_disable(port);
 		return;
-
-	if (rs485conf->flags & SER_RS485_ENABLED) {
-		if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
-			mctrl_gpio_set(stm32_port->gpios,
-					stm32_port->port.mctrl | TIOCM_RTS);
-		} else {
-			mctrl_gpio_set(stm32_port->gpios,
-					stm32_port->port.mctrl & ~TIOCM_RTS);
-		}
 	}
 
+	stm32_usart_rs485_rts_enable(port);
+
 	stm32_usart_transmit_chars(port);
 }
 
@@ -691,6 +864,11 @@
 	u32 val, isr;
 	int ret;
 
+	if (stm32_port->tx_dma_busy) {
+		dmaengine_terminate_async(stm32_port->tx_ch);
+		stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAT);
+	}
+
 	/* Disable modem control interrupts */
 	stm32_usart_disable_ms(port);
 
@@ -790,13 +968,22 @@
 	 * CS8 or (CS7 + parity), 8 bits word aka [M1:M0] = 0b00
 	 * M0 and M1 already cleared by cr1 initialization.
 	 */
-	if (bits == 9)
+	if (bits == 9) {
 		cr1 |= USART_CR1_M0;
-	else if ((bits == 7) && cfg->has_7bits_data)
+	} else if ((bits == 7) && cfg->has_7bits_data) {
 		cr1 |= USART_CR1_M1;
-	else if (bits != 8)
+	} else if (bits != 8) {
 		dev_dbg(port->dev, "Unsupported data bits config: %u bits\n"
 			, bits);
+		cflag &= ~CSIZE;
+		cflag |= CS8;
+		termios->c_cflag = cflag;
+		bits = 8;
+		if (cflag & PARENB) {
+			bits++;
+			cr1 |= USART_CR1_M0;
+		}
+	}
 
 	if (ofs->rtor != UNDEF_REG && (stm32_port->rx_ch ||
 				       (stm32_port->fifoen &&
@@ -810,9 +997,11 @@
 		stm32_port->cr1_irq = USART_CR1_RTOIE;
 		writel_relaxed(bits, port->membase + ofs->rtor);
 		cr2 |= USART_CR2_RTOEN;
-		/* Not using dma, enable fifo threshold irq */
-		if (!stm32_port->rx_ch)
-			stm32_port->cr3_irq =  USART_CR3_RXFTIE;
+		/*
+		 * Enable fifo threshold irq in two cases, either when there is no DMA, or when
+		 * wake up over usart, from low power until the DMA gets re-enabled by resume.
+		 */
+		stm32_port->cr3_irq =  USART_CR3_RXFTIE;
 	}
 
 	cr1 |= stm32_port->cr1_irq;
@@ -875,8 +1064,16 @@
 	if ((termios->c_cflag & CREAD) == 0)
 		port->ignore_status_mask |= USART_SR_DUMMY_RX;
 
-	if (stm32_port->rx_ch)
+	if (stm32_port->rx_ch) {
+		/*
+		 * Setup DMA to collect only valid data and enable error irqs.
+		 * This also enables break reception when using DMA.
+		 */
+		cr1 |= USART_CR1_PEIE;
+		cr3 |= USART_CR3_EIE;
 		cr3 |= USART_CR3_DMAR;
+		cr3 |= USART_CR3_DDRE;
+	}
 
 	if (rs485conf->flags & SER_RS485_ENABLED) {
 		stm32_usart_config_reg_rs485(&cr1, &cr3,
@@ -1205,9 +1402,9 @@
 		return -ENODEV;
 	}
 
-	/* No callback as dma buffer is drained on usart interrupt */
-	desc->callback = NULL;
-	desc->callback_param = NULL;
+	/* Set DMA callback */
+	desc->callback = stm32_usart_rx_dma_complete;
+	desc->callback_param = port;
 
 	/* Push current DMA transaction in the pending queue */
 	ret = dma_submit_error(dmaengine_submit(desc));
@@ -1276,22 +1473,10 @@
 	if (!stm32port->info)
 		return -EINVAL;
 
-	ret = stm32_usart_init_port(stm32port, pdev);
-	if (ret)
-		return ret;
-
-	if (stm32port->wakeup_src) {
-		device_set_wakeup_capable(&pdev->dev, true);
-		ret = dev_pm_set_wake_irq(&pdev->dev, stm32port->port.irq);
-		if (ret)
-			goto err_deinit_port;
-	}
-
 	stm32port->rx_ch = dma_request_chan(&pdev->dev, "rx");
-	if (PTR_ERR(stm32port->rx_ch) == -EPROBE_DEFER) {
-		ret = -EPROBE_DEFER;
-		goto err_wakeirq;
-	}
+	if (PTR_ERR(stm32port->rx_ch) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
 	/* Fall back in interrupt mode for any non-deferral error */
 	if (IS_ERR(stm32port->rx_ch))
 		stm32port->rx_ch = NULL;
@@ -1305,6 +1490,17 @@
 	if (IS_ERR(stm32port->tx_ch))
 		stm32port->tx_ch = NULL;
 
+	ret = stm32_usart_init_port(stm32port, pdev);
+	if (ret)
+		goto err_dma_tx;
+
+	if (stm32port->wakeup_src) {
+		device_set_wakeup_capable(&pdev->dev, true);
+		ret = dev_pm_set_wake_irq(&pdev->dev, stm32port->port.irq);
+		if (ret)
+			goto err_deinit_port;
+	}
+
 	if (stm32port->rx_ch && stm32_usart_of_dma_rx_probe(stm32port, pdev)) {
 		/* Fall back in interrupt mode */
 		dma_release_channel(stm32port->rx_ch);
@@ -1341,19 +1537,11 @@
 	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_put_noidle(&pdev->dev);
 
-	if (stm32port->tx_ch) {
+	if (stm32port->tx_ch)
 		stm32_usart_of_dma_tx_remove(stm32port, pdev);
-		dma_release_channel(stm32port->tx_ch);
-	}
-
 	if (stm32port->rx_ch)
 		stm32_usart_of_dma_rx_remove(stm32port, pdev);
 
-err_dma_rx:
-	if (stm32port->rx_ch)
-		dma_release_channel(stm32port->rx_ch);
-
-err_wakeirq:
 	if (stm32port->wakeup_src)
 		dev_pm_clear_wake_irq(&pdev->dev);
 
@@ -1363,6 +1551,14 @@
 
 	stm32_usart_deinit_port(stm32port);
 
+err_dma_tx:
+	if (stm32port->tx_ch)
+		dma_release_channel(stm32port->tx_ch);
+
+err_dma_rx:
+	if (stm32port->rx_ch)
+		dma_release_channel(stm32port->rx_ch);
+
 	return ret;
 }
 
@@ -1372,6 +1568,7 @@
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	int err;
+	u32 cr3;
 
 	pm_runtime_get_sync(&pdev->dev);
 	err = uart_remove_one_port(&stm32_usart_driver, port);
@@ -1382,10 +1579,14 @@
 	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_put_noidle(&pdev->dev);
 
-	stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAR);
+	stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_PEIE);
+	cr3 = readl_relaxed(port->membase + ofs->cr3);
+	cr3 &= ~USART_CR3_EIE;
+	cr3 &= ~USART_CR3_DMAR;
+	cr3 &= ~USART_CR3_DDRE;
+	writel_relaxed(cr3, port->membase + ofs->cr3);
 
 	if (stm32_port->tx_ch) {
-		dmaengine_terminate_async(stm32_port->tx_ch);
 		stm32_usart_of_dma_tx_remove(stm32_port, pdev);
 		dma_release_channel(stm32_port->tx_ch);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/stm32-usart.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/stm32-usart.h
@@ -109,7 +109,7 @@
 /* USART_SR (F4) / USART_ISR (F7) */
 #define USART_SR_PE		BIT(0)
 #define USART_SR_FE		BIT(1)
-#define USART_SR_NF		BIT(2)
+#define USART_SR_NE		BIT(2)		/* F7 (NF for F4) */
 #define USART_SR_ORE		BIT(3)
 #define USART_SR_IDLE		BIT(4)
 #define USART_SR_RXNE		BIT(5)
@@ -126,7 +126,8 @@
 #define USART_SR_SBKF		BIT(18)		/* F7 */
 #define USART_SR_WUF		BIT(20)		/* H7 */
 #define USART_SR_TEACK		BIT(21)		/* F7 */
-#define USART_SR_ERR_MASK	(USART_SR_ORE | USART_SR_FE | USART_SR_PE)
+#define USART_SR_ERR_MASK	(USART_SR_ORE | USART_SR_NE | USART_SR_FE |\
+				 USART_SR_PE)
 /* Dummy bits */
 #define USART_SR_DUMMY_RX	BIT(16)
 
@@ -246,9 +247,9 @@
 #define STM32_SERIAL_NAME "ttySTM"
 #define STM32_MAX_PORTS 8
 
-#define RX_BUF_L 200		 /* dma rx buffer length     */
-#define RX_BUF_P RX_BUF_L	 /* dma rx buffer period     */
-#define TX_BUF_L 200		 /* dma tx buffer length     */
+#define RX_BUF_L 4096		 /* dma rx buffer length     */
+#define RX_BUF_P (RX_BUF_L / 2)	 /* dma rx buffer period     */
+#define TX_BUF_L RX_BUF_L	 /* dma tx buffer length     */
 
 struct stm32_port {
 	struct uart_port port;
@@ -267,11 +268,13 @@
 	bool hw_flow_control;
 	bool swap;		 /* swap RX & TX pins */
 	bool fifoen;
+	bool txdone;
 	int rxftcfg;		/* RX FIFO threshold CFG      */
 	int txftcfg;		/* TX FIFO threshold CFG      */
 	bool wakeup_src;
 	int rdr_mask;		/* receive data register mask */
 	struct mctrl_gpios *gpios; /* modem control gpios */
+	struct dma_tx_state rx_dma_state;
 };
 
 static struct stm32_port stm32_ports[STM32_MAX_PORTS];
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/sunsab.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/sunsab.c
@@ -1137,7 +1137,13 @@
 		}
 	}
 
-	return platform_driver_register(&sab_driver);
+	err = platform_driver_register(&sab_driver);
+	if (err) {
+		kfree(sunsab_ports);
+		sunsab_ports = NULL;
+	}
+
+	return err;
 }
 
 static void __exit sunsab_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/tegra-tcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/tegra-tcu.c
@@ -101,7 +101,7 @@
 			break;
 
 		tegra_tcu_write(tcu, &xmit->buf[xmit->tail], count);
-		xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
+		uart_xmit_advance(port, count);
 	}
 
 	uart_write_wakeup(port);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/uartlite.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/uartlite.c
@@ -297,7 +297,6 @@
 	struct uartlite_data *pdata = port->private_data;
 
 	uart_out32(0, ULITE_CONTROL, port);
-	uart_in32(ULITE_CONTROL, port); /* dummy */
 	free_irq(port->irq, port);
 	clk_disable(pdata->clk);
 }
@@ -368,7 +367,6 @@
 	}
 
 	pdata->reg_ops = &uartlite_be;
-	ret = uart_in32(ULITE_CONTROL, port);
 	uart_out32(ULITE_CONTROL_RST_TX, ULITE_CONTROL, port);
 	ret = uart_in32(ULITE_STATUS, port);
 	/* Endianess detection */
@@ -612,7 +610,7 @@
  *
  * Returns: 0 on success, <0 otherwise
  */
-static int ulite_assign(struct device *dev, int id, u32 base, int irq,
+static int ulite_assign(struct device *dev, int id, phys_addr_t base, int irq,
 			struct uartlite_data *pdata)
 {
 	struct uart_port *port;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/ucc_uart.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/ucc_uart.c
@@ -1137,6 +1137,8 @@
 		/* No compatible property, so try the name. */
 		soc_string = np->name;
 
+	of_node_put(np);
+
 	/* Extract the SOC number from the "PowerPC," string */
 	if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc)
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/serial/xilinx_uartps.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/serial/xilinx_uartps.c
@@ -2,7 +2,7 @@
 /*
  * Cadence UART driver (found in Xilinx Zynq)
  *
- * 2011 - 2014 (C) Xilinx Inc.
+ * Copyright (c) 2011 - 2014 Xilinx, Inc.
  *
  * This driver has originally been pushed by Xilinx using a Zynq-branding. This
  * still shows in the naming of this file, the kconfig symbols and some symbols
@@ -22,7 +22,10 @@
 #include <linux/of.h>
 #include <linux/module.h>
 #include <linux/pm_runtime.h>
-#include <linux/iopoll.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
 
 #define CDNS_UART_TTY_NAME	"ttyPS"
 #define CDNS_UART_NAME		"xuartps"
@@ -34,12 +37,12 @@
 #define TX_TIMEOUT		500000
 
 /* Rx Trigger level */
-static int rx_trigger_level = 56;
+static uint rx_trigger_level = 56;
 module_param(rx_trigger_level, uint, 0444);
 MODULE_PARM_DESC(rx_trigger_level, "Rx trigger level, 1-63 bytes");
 
 /* Rx Timeout */
-static int rx_timeout = 10;
+static uint rx_timeout = 10;
 module_param(rx_timeout, uint, 0444);
 MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
 
@@ -193,6 +196,10 @@
  * @clk_rate_change_nb:	Notifier block for clock changes
  * @quirks:		Flags for RXBS support.
  * @cts_override:	Modem control state override
+ * @gpiod_rts:		Pointer to the gpio descriptor
+ * @rs485_tx_started:	RS485 tx state
+ * @tx_timer:		Timer for tx
+ * @rstc:		Pointer to the reset control
  */
 struct cdns_uart {
 	struct uart_port	*port;
@@ -203,10 +210,22 @@
 	struct notifier_block	clk_rate_change_nb;
 	u32			quirks;
 	bool cts_override;
+	struct gpio_desc	*gpiod_rts;
+	bool			rs485_tx_started;
+	struct hrtimer		tx_timer;
+	struct reset_control	*rstc;
 };
 struct cdns_platform_data {
 	u32 quirks;
 };
+
+struct serial_rs485 cdns_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+		 SER_RS485_RTS_AFTER_SEND,
+	.delay_rts_before_send = 1,
+	.delay_rts_after_send = 1,
+};
+
 #define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
 		clk_rate_change_nb)
 
@@ -229,6 +248,13 @@
 
 	is_rxbs_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
 
+	/*
+	 * RXEMPTY will never be set if RX is disabled as read bytes
+	 * will not be removed from the FIFO
+	 */
+	if (readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_RX_DIS)
+		return;
+
 	while ((readl(port->membase + CDNS_UART_SR) &
 		CDNS_UART_SR_RXEMPTY) != CDNS_UART_SR_RXEMPTY) {
 		if (is_rxbs_support)
@@ -268,7 +294,7 @@
 				continue;
 		}
 
-		if (uart_handle_sysrq_char(port, data))
+		if (uart_prepare_sysrq_char(port, data))
 			continue;
 
 		if (is_rxbs_support) {
@@ -306,16 +332,113 @@
 }
 
 /**
- * cdns_uart_handle_tx - Handle the bytes to be Txed.
+ * cdns_rts_gpio_enable - Configure RTS/GPIO to high/low
+ * @cdns_uart: Handle to the cdns_uart
+ * @enable: Value to be set to RTS/GPIO
+ */
+static void cdns_rts_gpio_enable(struct cdns_uart *cdns_uart, bool enable)
+{
+	u32 val;
+
+	if (cdns_uart->gpiod_rts) {
+		gpiod_set_value(cdns_uart->gpiod_rts, enable);
+	} else {
+		val = readl(cdns_uart->port->membase + CDNS_UART_MODEMCR);
+		if (enable)
+			val |= CDNS_UART_MODEMCR_RTS;
+		else
+			val &= ~CDNS_UART_MODEMCR_RTS;
+		writel(val, cdns_uart->port->membase + CDNS_UART_MODEMCR);
+	}
+}
+
+/**
+ * cdns_rs485_tx_setup - Tx setup specific to rs485
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static void cdns_rs485_tx_setup(struct cdns_uart *cdns_uart)
+{
+	bool enable;
+
+	enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_ON_SEND;
+	cdns_rts_gpio_enable(cdns_uart, enable);
+
+	cdns_uart->rs485_tx_started = true;
+}
+
+/**
+ * cdns_rs485_rx_setup - Rx setup specific to rs485
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static void cdns_rs485_rx_setup(struct cdns_uart *cdns_uart)
+{
+	bool enable;
+
+	enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_AFTER_SEND;
+	cdns_rts_gpio_enable(cdns_uart, enable);
+
+	cdns_uart->rs485_tx_started = false;
+}
+
+/**
+ * cdns_uart_tx_empty -  Check whether TX is empty
+ * @port: Handle to the uart port structure
+ *
+ * Return: TIOCSER_TEMT on success, 0 otherwise
+ */
+static unsigned int cdns_uart_tx_empty(struct uart_port *port)
+{
+	unsigned int status;
+
+	status = readl(port->membase + CDNS_UART_SR);
+	status &= (CDNS_UART_SR_TXEMPTY | CDNS_UART_SR_TACTIVE);
+	return (status == CDNS_UART_SR_TXEMPTY) ? TIOCSER_TEMT : 0;
+}
+
+/**
+ * cdns_rs485_rx_callback - Timer rx callback handler for rs485.
+ * @t: Handle to the hrtimer structure
+ */
+static enum hrtimer_restart cdns_rs485_rx_callback(struct hrtimer *t)
+{
+	struct cdns_uart *cdns_uart = container_of(t, struct cdns_uart, tx_timer);
+
+	/*
+	 * Default Rx should be setup, because Rx signaling path
+	 * need to enable to receive data.
+	 */
+	cdns_rs485_rx_setup(cdns_uart);
+
+	return HRTIMER_NORESTART;
+}
+
+/**
+ * cdns_calc_after_tx_delay - calculate delay required for after tx.
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static u64 cdns_calc_after_tx_delay(struct cdns_uart *cdns_uart)
+{
+	/*
+	 * Frame time + stop bit time + rs485.delay_rts_after_send
+	 */
+	return cdns_uart->port->frame_time
+	       + DIV_ROUND_UP(cdns_uart->port->frame_time, 7)
+	       + (u64)cdns_uart->port->rs485.delay_rts_after_send * NSEC_PER_MSEC;
+}
+
+/**
+ * cdns_uart_handle_tx - Handle the bytes to be transmitted.
  * @dev_id: Id of the UART port
  * Return: None
  */
 static void cdns_uart_handle_tx(void *dev_id)
 {
 	struct uart_port *port = (struct uart_port *)dev_id;
+	struct cdns_uart *cdns_uart = port->private_data;
 	unsigned int numbytes;
 
-	if (uart_circ_empty(&port->state->xmit)) {
+	if (uart_circ_empty(&port->state->xmit) || uart_tx_stopped(port)) {
+		/* Disable the TX Empty interrupt */
 		writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IDR);
 	} else {
 		numbytes = port->fifosize;
@@ -348,6 +471,16 @@
 				&port->state->xmit) < WAKEUP_CHARS)
 			uart_write_wakeup(port);
 	}
+
+	/* Enable the TX Empty interrupt */
+	writel(CDNS_UART_IXR_TXEMPTY, cdns_uart->port->membase + CDNS_UART_IER);
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED &&
+	    (uart_circ_empty(&port->state->xmit) || uart_tx_stopped(port))) {
+		cdns_uart->tx_timer.function = &cdns_rs485_rx_callback;
+		hrtimer_start(&cdns_uart->tx_timer,
+			      ns_to_ktime(cdns_calc_after_tx_delay(cdns_uart)), HRTIMER_MODE_REL);
+	}
 }
 
 /**
@@ -375,6 +508,8 @@
 		isrstatus &= ~CDNS_UART_IXR_TXEMPTY;
 	}
 
+	isrstatus &= port->read_status_mask;
+	isrstatus &= ~port->ignore_status_mask;
 	/*
 	 * Skip RX processing if RX is disabled as RXEMPTY will never be set
 	 * as read bytes will not be removed from the FIFO.
@@ -383,7 +518,7 @@
 	    !(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_RX_DIS))
 		cdns_uart_handle_rx(dev_id, isrstatus);
 
-	spin_unlock(&port->lock);
+	uart_unlock_and_check_sysrq(port);
 	return IRQ_HANDLED;
 }
 
@@ -579,12 +714,28 @@
 #endif
 
 /**
+ * cdns_rs485_tx_callback - Timer tx callback handler for rs485.
+ * @t: Handle to the hrtimer structure
+ */
+static enum hrtimer_restart cdns_rs485_tx_callback(struct hrtimer *t)
+{
+	struct cdns_uart *cdns_uart = container_of(t, struct cdns_uart, tx_timer);
+
+	uart_port_lock(cdns_uart->port);
+	cdns_uart_handle_tx(cdns_uart->port);
+	uart_port_unlock(cdns_uart->port);
+
+	return HRTIMER_NORESTART;
+}
+
+/**
  * cdns_uart_start_tx -  Start transmitting bytes
  * @port: Handle to the uart port structure
  */
 static void cdns_uart_start_tx(struct uart_port *port)
 {
 	unsigned int status;
+	struct cdns_uart *cdns_uart = port->private_data;
 
 	if (uart_tx_stopped(port))
 		return;
@@ -601,11 +752,19 @@
 	if (uart_circ_empty(&port->state->xmit))
 		return;
 
-	cdns_uart_handle_tx(port);
-
+	/* Clear the TX Empty interrupt */
 	writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR);
-	/* Enable the TX Empty interrupt */
-	writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER);
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED) {
+		if (!cdns_uart->rs485_tx_started) {
+			cdns_uart->tx_timer.function = &cdns_rs485_tx_callback;
+			cdns_rs485_tx_setup(cdns_uart);
+			return hrtimer_start(&cdns_uart->tx_timer,
+					     ms_to_ktime(port->rs485.delay_rts_before_send),
+					     HRTIMER_MODE_REL);
+		}
+	}
+	cdns_uart_handle_tx(port);
 }
 
 /**
@@ -615,6 +774,10 @@
 static void cdns_uart_stop_tx(struct uart_port *port)
 {
 	unsigned int regval;
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
+		cdns_rs485_rx_setup(cdns_uart);
 
 	regval = readl(port->membase + CDNS_UART_CR);
 	regval |= CDNS_UART_CR_TX_DIS;
@@ -640,21 +803,6 @@
 }
 
 /**
- * cdns_uart_tx_empty -  Check whether TX is empty
- * @port: Handle to the uart port structure
- *
- * Return: TIOCSER_TEMT on success, 0 otherwise
- */
-static unsigned int cdns_uart_tx_empty(struct uart_port *port)
-{
-	unsigned int status;
-
-	status = readl(port->membase + CDNS_UART_SR) &
-		       (CDNS_UART_SR_TXEMPTY | CDNS_UART_SR_TACTIVE);
-	return (status == CDNS_UART_SR_TXEMPTY) ? TIOCSER_TEMT : 0;
-}
-
-/**
  * cdns_uart_break_ctl - Based on the input ctl we have to start or stop
  *			transmitting char breaks
  * @port: Handle to the uart port structure
@@ -825,6 +973,10 @@
 
 	is_brk_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
 
+	ret = reset_control_deassert(cdns_uart->rstc);
+	if (ret)
+		return ret;
+
 	spin_lock_irqsave(&port->lock, flags);
 
 	/* Disable the TX and RX */
@@ -841,6 +993,9 @@
 		(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
 		cpu_relax();
 
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
+		cdns_rs485_rx_setup(cdns_uart);
+
 	/*
 	 * Clear the RX disable bit and then set the RX enable bit to enable
 	 * the receiver.
@@ -900,6 +1055,10 @@
 {
 	int status;
 	unsigned long flags;
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
+		hrtimer_cancel(&cdns_uart->tx_timer);
 
 	spin_lock_irqsave(&port->lock, flags);
 
@@ -1045,6 +1204,8 @@
 
 	if (mctrl & TIOCM_RTS)
 		val |= CDNS_UART_MODEMCR_RTS;
+	if (cdns_uart_data->gpiod_rts)
+		gpiod_set_value(cdns_uart_data->gpiod_rts, !(mctrl & TIOCM_RTS));
 	if (mctrl & TIOCM_DTR)
 		val |= CDNS_UART_MODEMCR_DTR;
 	if (mctrl & TIOCM_LOOP)
@@ -1099,13 +1260,17 @@
 static void cdns_uart_pm(struct uart_port *port, unsigned int state,
 		   unsigned int oldstate)
 {
+	int ret;
+
 	switch (state) {
 	case UART_PM_STATE_OFF:
 		pm_runtime_mark_last_busy(port->dev);
 		pm_runtime_put_autosuspend(port->dev);
 		break;
 	default:
-		pm_runtime_get_sync(port->dev);
+		ret = pm_runtime_get_sync(port->dev);
+		if (ret < 0)
+			dev_err(port->dev, "Failed to enable clocks\n");
 		break;
 	}
 }
@@ -1143,6 +1308,13 @@
  */
 static void cdns_uart_console_putchar(struct uart_port *port, int ch)
 {
+	unsigned int ctrl_reg;
+
+	ctrl_reg = readl(port->membase + CDNS_UART_CR);
+	while (ctrl_reg & CDNS_UART_CR_TX_DIS) {
+		ctrl_reg = readl(port->membase + CDNS_UART_CR);
+		cpu_relax();
+	}
 	while (readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)
 		cpu_relax();
 	writel(ch, port->membase + CDNS_UART_FIFO);
@@ -1214,10 +1386,8 @@
 	unsigned int imr, ctrl;
 	int locked = 1;
 
-	if (port->sysrq)
-		locked = 0;
-	else if (oops_in_progress)
-		locked = spin_trylock_irqsave(&port->lock, flags);
+	if (oops_in_progress)
+		locked = uart_port_trylock_irqsave(port, &flags);
 	else
 		spin_lock_irqsave(&port->lock, flags);
 
@@ -1342,12 +1512,18 @@
 	unsigned long flags;
 	u32 ctrl_reg;
 	int may_wake;
+	int ret;
 
 	may_wake = device_may_wakeup(device);
 
 	if (console_suspend_enabled && uart_console(port) && !may_wake) {
-		clk_enable(cdns_uart->pclk);
-		clk_enable(cdns_uart->uartclk);
+		ret = clk_enable(cdns_uart->pclk);
+		if (ret)
+			return ret;
+
+		ret = clk_enable(cdns_uart->uartclk);
+		if (ret)
+			return ret;
 
 		spin_lock_irqsave(&port->lock, flags);
 
@@ -1396,9 +1572,17 @@
 {
 	struct uart_port *port = dev_get_drvdata(dev);
 	struct cdns_uart *cdns_uart = port->private_data;
+	int ret;
+
+	ret = clk_enable(cdns_uart->pclk);
+	if (ret)
+		return ret;
 
-	clk_enable(cdns_uart->pclk);
-	clk_enable(cdns_uart->uartclk);
+	ret = clk_enable(cdns_uart->uartclk);
+	if (ret) {
+		clk_disable(cdns_uart->pclk);
+		return ret;
+	}
 	return 0;
 };
 
@@ -1424,6 +1608,115 @@
 /* Temporary variable for storing number of instances */
 static int instances;
 
+/* Stores static aliases list */
+static DECLARE_BITMAP(alias_bitmap, CDNS_UART_NR_PORTS);
+static int alias_bitmap_initialized;
+
+/* Stores actual bitmap of allocated IDs with alias IDs together */
+static DECLARE_BITMAP(bitmap, CDNS_UART_NR_PORTS);
+/* Protect bitmap operations to have unique IDs */
+static DEFINE_MUTEX(bitmap_lock);
+
+static int cdns_get_id(struct platform_device *pdev)
+{
+	int id, ret;
+
+	mutex_lock(&bitmap_lock);
+
+	/* Alias list is stable that's why get alias bitmap only once */
+	if (!alias_bitmap_initialized) {
+		ret = of_alias_get_alias_list(cdns_uart_of_match, "serial",
+					      alias_bitmap, CDNS_UART_NR_PORTS);
+		if (ret)
+			return ret;
+
+		alias_bitmap_initialized++;
+	}
+
+	/* Make sure that alias ID is not taken by instance without alias */
+	bitmap_or(bitmap, bitmap, alias_bitmap, CDNS_UART_NR_PORTS);
+
+	dev_dbg(&pdev->dev, "Alias bitmap: %*pb\n",
+		CDNS_UART_NR_PORTS, bitmap);
+
+	/* Look for a serialN alias */
+	id = of_alias_get_id(pdev->dev.of_node, "serial");
+	if (id < 0) {
+		dev_warn(&pdev->dev,
+			 "No serial alias passed. Using the first free id\n");
+
+		/*
+		 * Start with id 0 and check if there is no serial0 alias
+		 * which points to device which is compatible with this driver.
+		 * If alias exists then try next free position.
+		 */
+		id = 0;
+
+		for (;;) {
+			dev_info(&pdev->dev, "Checking id %d\n", id);
+			id = find_next_zero_bit(bitmap, CDNS_UART_NR_PORTS, id);
+
+			/* No free empty instance */
+			if (id == CDNS_UART_NR_PORTS) {
+				dev_err(&pdev->dev, "No free ID\n");
+				mutex_unlock(&bitmap_lock);
+				return -EINVAL;
+			}
+
+			dev_dbg(&pdev->dev, "The empty id is %d\n", id);
+			/* Check if ID is empty */
+			if (!test_and_set_bit(id, bitmap)) {
+				/* Break the loop if bit is taken */
+				dev_dbg(&pdev->dev,
+					"Selected ID %d allocation passed\n",
+					id);
+				break;
+			}
+			dev_dbg(&pdev->dev,
+				"Selected ID %d allocation failed\n", id);
+			/* if taking bit fails then try next one */
+			id++;
+		}
+	}
+
+	mutex_unlock(&bitmap_lock);
+
+	return id;
+}
+
+/**
+ * cdns_rs485_config - Called when an application calls TIOCSRS485 ioctl.
+ * @port: Pointer to the uart_port structure
+ * @termios: Pointer to the ktermios structure
+ * @rs485: Pointer to the serial_rs485 structure
+ *
+ * Return: 0
+ */
+static int cdns_rs485_config(struct uart_port *port, struct ktermios *termios,
+			     struct serial_rs485 *rs485)
+{
+	u32 val;
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		dev_dbg(port->dev, "Setting UART to RS485\n");
+		/* Make sure auto RTS is disabled */
+		val = readl(port->membase + CDNS_UART_MODEMCR);
+		val &= ~CDNS_UART_MODEMCR_FCM;
+		writel(val, port->membase + CDNS_UART_MODEMCR);
+
+		/* Timer setup */
+		hrtimer_init(&cdns_uart->tx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+		cdns_uart->tx_timer.function = &cdns_rs485_tx_callback;
+
+		/* Disable transmitter and make Rx setup*/
+		cdns_uart_stop_tx(port);
+	} else {
+		hrtimer_cancel(&cdns_uart->tx_timer);
+	}
+	return 0;
+}
+
 /**
  * cdns_uart_probe - Platform driver probe
  * @pdev: Pointer to the platform device structure
@@ -1446,15 +1739,9 @@
 	if (!port)
 		return -ENOMEM;
 
-	/* Look for a serialN alias */
-	id = of_alias_get_id(pdev->dev.of_node, "serial");
+	id = cdns_get_id(pdev);
 	if (id < 0)
-		id = 0;
-
-	if (id >= CDNS_UART_NR_PORTS) {
-		dev_err(&pdev->dev, "Cannot get uart_port structure\n");
-		return -ENODEV;
-	}
+		return id;
 
 	if (!cdns_uart_uart_driver.state) {
 		cdns_uart_uart_driver.owner = THIS_MODULE;
@@ -1463,6 +1750,7 @@
 		cdns_uart_uart_driver.major = CDNS_UART_MAJOR;
 		cdns_uart_uart_driver.minor = CDNS_UART_MINOR;
 		cdns_uart_uart_driver.nr = CDNS_UART_NR_PORTS;
+
 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
 		cdns_uart_uart_driver.cons = &cdns_uart_console;
 #endif
@@ -1513,6 +1801,13 @@
 		dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
 	}
 
+	cdns_uart_data->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(cdns_uart_data->rstc)) {
+		rc = PTR_ERR(cdns_uart_data->rstc);
+		dev_err_probe(&pdev->dev, rc, "Cannot get UART reset\n");
+		goto err_out_unregister_driver;
+	}
+
 	rc = clk_prepare_enable(cdns_uart_data->pclk);
 	if (rc) {
 		dev_err(&pdev->dev, "Unable to enable pclk clock.\n");
@@ -1564,9 +1859,25 @@
 	port->dev = &pdev->dev;
 	port->uartclk = clk_get_rate(cdns_uart_data->uartclk);
 	port->private_data = cdns_uart_data;
+	port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
+			CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
+	port->rs485_config = cdns_rs485_config;
+	port->rs485_supported = &cdns_rs485_supported;
 	cdns_uart_data->port = port;
 	platform_set_drvdata(pdev, port);
 
+	rc = uart_get_rs485_mode(port);
+	if (rc)
+		goto err_out_clk_notifier;
+
+	cdns_uart_data->gpiod_rts = devm_gpiod_get_optional(&pdev->dev, "rts",
+							    GPIOD_OUT_LOW);
+	if (IS_ERR(cdns_uart_data->gpiod_rts)) {
+		rc = PTR_ERR(cdns_uart_data->gpiod_rts);
+		dev_err(port->dev, "xuartps: devm_gpiod_get_optional failed\n");
+		goto err_out_clk_notifier;
+	}
+
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
 	pm_runtime_set_active(&pdev->dev);
@@ -1585,6 +1896,8 @@
 		console_port = port;
 	}
 #endif
+	if (cdns_uart_data->port->rs485.flags & SER_RS485_ENABLED)
+		cdns_rs485_rx_setup(cdns_uart_data);
 
 	rc = uart_add_one_port(&cdns_uart_uart_driver, port);
 	if (rc) {
@@ -1613,6 +1926,7 @@
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_dont_use_autosuspend(&pdev->dev);
+err_out_clk_notifier:
 #ifdef CONFIG_COMMON_CLK
 	clk_notifier_unregister(cdns_uart_data->uartclk,
 			&cdns_uart_data->clk_rate_change_nb);
@@ -1624,6 +1938,11 @@
 err_out_unregister_driver:
 	if (!instances)
 		uart_unregister_driver(cdns_uart_data->cdns_uart_driver);
+
+	mutex_lock(&bitmap_lock);
+	clear_bit(port->line, bitmap);
+	mutex_unlock(&bitmap_lock);
+
 	return rc;
 }
 
@@ -1646,6 +1965,9 @@
 #endif
 	rc = uart_remove_one_port(cdns_uart_data->cdns_uart_driver, port);
 	port->mapbase = 0;
+	mutex_lock(&bitmap_lock);
+	clear_bit(port->line, bitmap);
+	mutex_unlock(&bitmap_lock);
 	clk_disable_unprepare(cdns_uart_data->uartclk);
 	clk_disable_unprepare(cdns_uart_data->pclk);
 	pm_runtime_disable(&pdev->dev);
@@ -1657,6 +1979,7 @@
 	if (console_port == port)
 		console_port = NULL;
 #endif
+	reset_control_assert(cdns_uart_data->rstc);
 
 	if (!--instances)
 		uart_unregister_driver(cdns_uart_data->cdns_uart_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/synclink_gt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/synclink_gt.c
@@ -1746,6 +1746,8 @@
  */
 static void hdlcdev_exit(struct slgt_info *info)
 {
+	if (!info->netdev)
+		return;
 	unregister_hdlc_device(info->netdev);
 	free_netdev(info->netdev);
 	info->netdev = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/sysrq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/sysrq.c
@@ -232,8 +232,10 @@
 	unsigned long flags;
 
 	/* Idle CPUs have no interesting backtrace. */
-	if (idle_cpu(smp_processor_id()))
+	if (idle_cpu(smp_processor_id())) {
+		pr_info("CPU%d: backtrace skipped as idling\n", smp_processor_id());
 		return;
+	}
 
 	raw_spin_lock_irqsave(&show_lock, flags);
 	pr_info("CPU%d:\n", smp_processor_id());
@@ -260,11 +262,15 @@
 
 		if (in_hardirq())
 			regs = get_irq_regs();
-		if (regs) {
-			pr_info("CPU%d:\n", smp_processor_id());
+
+		pr_info("CPU%d:\n", get_cpu());
+		if (regs)
 			show_regs(regs);
-		}
+		else
+			show_stack(NULL, NULL, KERN_INFO);
+
 		schedule_work(&sysrq_showallcpus);
+		put_cpu();
 	}
 }
 
@@ -296,7 +302,7 @@
 static void sysrq_handle_showstate(int key)
 {
 	show_state();
-	show_workqueue_state();
+	show_all_workqueues();
 }
 static const struct sysrq_key_op sysrq_showstate_op = {
 	.handler	= sysrq_handle_showstate,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/tty.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/tty.h
@@ -62,6 +62,8 @@
 int tty_check_change(struct tty_struct *tty);
 void __stop_tty(struct tty_struct *tty);
 void __start_tty(struct tty_struct *tty);
+void tty_write_unlock(struct tty_struct *tty);
+int tty_write_lock(struct tty_struct *tty, bool ndelay);
 void tty_vhangup_session(struct tty_struct *tty);
 void tty_open_proc_set_tty(struct file *filp, struct tty_struct *tty);
 int tty_signal_session_leader(struct tty_struct *tty, int exit_session);
@@ -111,4 +113,7 @@
 
 ssize_t redirected_tty_write(struct kiocb *, struct iov_iter *);
 
+int tty_insert_flip_string_and_push_buffer(struct tty_port *port,
+		const unsigned char *chars, size_t cnt);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/tty_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/tty_buffer.c
@@ -174,7 +174,8 @@
 	 */
 	if (atomic_read(&port->buf.mem_used) > port->buf.mem_limit)
 		return NULL;
-	p = kmalloc(sizeof(struct tty_buffer) + 2 * size, GFP_ATOMIC);
+	p = kmalloc(sizeof(struct tty_buffer) + 2 * size,
+		    GFP_ATOMIC | __GFP_NOWARN);
 	if (p == NULL)
 		return NULL;
 
@@ -402,27 +403,6 @@
 EXPORT_SYMBOL(__tty_insert_flip_char);
 
 /**
- *	tty_schedule_flip	-	push characters to ldisc
- *	@port: tty port to push from
- *
- *	Takes any pending buffers and transfers their ownership to the
- *	ldisc side of the queue. It then schedules those characters for
- *	processing by the line discipline.
- */
-
-void tty_schedule_flip(struct tty_port *port)
-{
-	struct tty_bufhead *buf = &port->buf;
-
-	/* paired w/ acquire in flush_to_ldisc(); ensures
-	 * flush_to_ldisc() sees buffer data.
-	 */
-	smp_store_release(&buf->tail->commit, buf->tail->used);
-	queue_work(system_unbound_wq, &buf->work);
-}
-EXPORT_SYMBOL(tty_schedule_flip);
-
-/**
  *	tty_prepare_flip_string		-	make room for characters
  *	@port: tty port
  *	@chars: return pointer for character write area
@@ -544,12 +524,24 @@
 		if (!count)
 			break;
 		head->read += count;
+
+		if (need_resched())
+			cond_resched();
 	}
 
 	mutex_unlock(&buf->lock);
 
 }
 
+static inline void tty_flip_buffer_commit(struct tty_buffer *tail)
+{
+	/*
+	 * Paired w/ acquire in flush_to_ldisc(); ensures flush_to_ldisc() sees
+	 * buffer data.
+	 */
+	smp_store_release(&tail->commit, tail->used);
+}
+
 /**
  *	tty_flip_buffer_push	-	terminal
  *	@port: tty port to push
@@ -563,11 +555,45 @@
 
 void tty_flip_buffer_push(struct tty_port *port)
 {
-	tty_schedule_flip(port);
+	struct tty_bufhead *buf = &port->buf;
+
+	tty_flip_buffer_commit(buf->tail);
+	queue_work(system_unbound_wq, &buf->work);
 }
 EXPORT_SYMBOL(tty_flip_buffer_push);
 
 /**
+ * tty_insert_flip_string_and_push_buffer - add characters to the tty buffer and
+ *	push
+ * @port: tty port
+ * @chars: characters
+ * @size: size
+ *
+ * The function combines tty_insert_flip_string() and tty_flip_buffer_push()
+ * with the exception of properly holding the @port->lock.
+ *
+ * To be used only internally (by pty currently).
+ *
+ * Returns: the number added.
+ */
+int tty_insert_flip_string_and_push_buffer(struct tty_port *port,
+		const unsigned char *chars, size_t size)
+{
+	struct tty_bufhead *buf = &port->buf;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	size = tty_insert_flip_string(port, chars, size);
+	if (size)
+		tty_flip_buffer_commit(buf->tail);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	queue_work(system_unbound_wq, &buf->work);
+
+	return size;
+}
+
+/**
  *	tty_buffer_init		-	prepare a tty buffer structure
  *	@port: tty port to initialise
  *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/tty_io.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/tty_io.c
@@ -950,13 +950,13 @@
 	return i;
 }
 
-static void tty_write_unlock(struct tty_struct *tty)
+void tty_write_unlock(struct tty_struct *tty)
 {
 	mutex_unlock(&tty->atomic_write_lock);
 	wake_up_interruptible_poll(&tty->write_wait, EPOLLOUT);
 }
 
-static int tty_write_lock(struct tty_struct *tty, int ndelay)
+int tty_write_lock(struct tty_struct *tty, bool ndelay)
 {
 	if (!mutex_trylock(&tty->atomic_write_lock)) {
 		if (ndelay)
@@ -1173,7 +1173,7 @@
 		return 0;
 	}
 
-	if (tty_write_lock(tty, 0) < 0)
+	if (tty_write_lock(tty, false) < 0)
 		return -ERESTARTSYS;
 
 	down_read(&tty->termios_rwsem);
@@ -1244,14 +1244,16 @@
 {
 	struct tty_struct *tty;
 
-	if (driver->ops->lookup)
+	if (driver->ops->lookup) {
 		if (!file)
 			tty = ERR_PTR(-EIO);
 		else
 			tty = driver->ops->lookup(driver, file, idx);
-	else
+	} else {
+		if (idx >= driver->num)
+			return ERR_PTR(-EINVAL);
 		tty = driver->ttys[idx];
-
+	}
 	if (!IS_ERR(tty))
 		tty_kref_get(tty);
 	return tty;
@@ -2502,22 +2504,25 @@
 		return 0;
 
 	if (tty->driver->flags & TTY_DRIVER_HARDWARE_BREAK)
-		retval = tty->ops->break_ctl(tty, duration);
-	else {
-		/* Do the work ourselves */
-		if (tty_write_lock(tty, 0) < 0)
-			return -EINTR;
-		retval = tty->ops->break_ctl(tty, -1);
-		if (retval)
-			goto out;
-		if (!signal_pending(current))
-			msleep_interruptible(duration);
+		return tty->ops->break_ctl(tty, duration);
+
+	/* Do the work ourselves */
+	if (tty_write_lock(tty, false) < 0)
+		return -EINTR;
+
+	retval = tty->ops->break_ctl(tty, -1);
+	if (!retval) {
+		msleep_interruptible(duration);
 		retval = tty->ops->break_ctl(tty, 0);
-out:
-		tty_write_unlock(tty);
-		if (signal_pending(current))
-			retval = -EINTR;
+	} else if (retval == -EOPNOTSUPP) {
+		/* some drivers can tell only dynamically */
+		retval = 0;
 	}
+	tty_write_unlock(tty);
+
+	if (signal_pending(current))
+		retval = -EINTR;
+
 	return retval;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/tty_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/tty_ioctl.c
@@ -421,22 +421,43 @@
 	tmp_termios.c_ispeed = tty_termios_input_baud_rate(&tmp_termios);
 	tmp_termios.c_ospeed = tty_termios_baud_rate(&tmp_termios);
 
-	ld = tty_ldisc_ref(tty);
-
-	if (ld != NULL) {
-		if ((opt & TERMIOS_FLUSH) && ld->ops->flush_buffer)
-			ld->ops->flush_buffer(tty);
-		tty_ldisc_deref(ld);
-	}
-
-	if (opt & TERMIOS_WAIT) {
-		tty_wait_until_sent(tty, 0);
-		if (signal_pending(current))
-			return -ERESTARTSYS;
+	if (opt & (TERMIOS_FLUSH|TERMIOS_WAIT)) {
+retry_write_wait:
+		retval = wait_event_interruptible(tty->write_wait, !tty_chars_in_buffer(tty));
+		if (retval < 0)
+			return retval;
+
+		if (tty_write_lock(tty, false) < 0)
+			goto retry_write_wait;
+
+		/* Racing writer? */
+		if (tty_chars_in_buffer(tty)) {
+			tty_write_unlock(tty);
+			goto retry_write_wait;
+		}
+
+		ld = tty_ldisc_ref(tty);
+		if (ld != NULL) {
+			if ((opt & TERMIOS_FLUSH) && ld->ops->flush_buffer)
+				ld->ops->flush_buffer(tty);
+			tty_ldisc_deref(ld);
+		}
+
+		if ((opt & TERMIOS_WAIT) && tty->ops->wait_until_sent) {
+			tty->ops->wait_until_sent(tty, 0);
+			if (signal_pending(current)) {
+				tty_write_unlock(tty);
+				return -ERESTARTSYS;
+			}
+		}
+
+		tty_set_termios(tty, &tmp_termios);
+
+		tty_write_unlock(tty);
+	} else {
+		tty_set_termios(tty, &tmp_termios);
 	}
 
-	tty_set_termios(tty, &tmp_termios);
-
 	/* FIXME: Arguably if tmp_termios == tty->termios AND the
 	   actual requested termios was not tmp_termios then we may
 	   want to return an error as no user requested change has
@@ -765,7 +786,7 @@
 			ret = -EFAULT;
 		return ret;
 	case TIOCSLCKTRMIOS:
-		if (!capable(CAP_SYS_ADMIN))
+		if (!checkpoint_restore_ns_capable(&init_user_ns))
 			return -EPERM;
 		copy_termios_locked(real_tty, &kterm);
 		if (user_termios_to_kernel_termios(&kterm,
@@ -782,7 +803,7 @@
 			ret = -EFAULT;
 		return ret;
 	case TIOCSLCKTRMIOS:
-		if (!capable(CAP_SYS_ADMIN))
+		if (!checkpoint_restore_ns_capable(&init_user_ns))
 			return -EPERM;
 		copy_termios_locked(real_tty, &kterm);
 		if (user_termios_to_kernel_termios_1(&kterm,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/tty_jobctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/tty_jobctrl.c
@@ -300,12 +300,7 @@
 		return;
 	}
 
-	spin_lock_irq(&current->sighand->siglock);
-	put_pid(current->signal->tty_old_pgrp);
-	current->signal->tty_old_pgrp = NULL;
-	tty = tty_kref_get(current->signal->tty);
-	spin_unlock_irq(&current->sighand->siglock);
-
+	tty = get_current_tty();
 	if (tty) {
 		unsigned long flags;
 
@@ -320,6 +315,16 @@
 		tty_kref_put(tty);
 	}
 
+	/* If tty->ctrl.pgrp is not NULL, it may be assigned to
+	 * current->signal->tty_old_pgrp in a race condition, and
+	 * cause pid memleak. Release current->signal->tty_old_pgrp
+	 * after tty->ctrl.pgrp set to NULL.
+	 */
+	spin_lock_irq(&current->sighand->siglock);
+	put_pid(current->signal->tty_old_pgrp);
+	current->signal->tty_old_pgrp = NULL;
+	spin_unlock_irq(&current->sighand->siglock);
+
 	/* Now clear signal->tty under the lock */
 	read_lock(&tasklist_lock);
 	session_clear_tty(task_session(current));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/tty_ldisc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/tty_ldisc.c
@@ -852,7 +852,7 @@
 		.data		= &tty_ldisc_autoload,
 		.maxlen		= sizeof(tty_ldisc_autoload),
 		.mode		= 0644,
-		.proc_handler	= proc_dointvec,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= SYSCTL_ONE,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/vcc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/vcc.c
@@ -578,18 +578,22 @@
 		return -ENOMEM;
 
 	name = kstrdup(dev_name(&vdev->dev), GFP_KERNEL);
+	if (!name) {
+		rv = -ENOMEM;
+		goto free_port;
+	}
 
 	rv = vio_driver_init(&port->vio, vdev, VDEV_CONSOLE_CON, vcc_versions,
 			     ARRAY_SIZE(vcc_versions), NULL, name);
 	if (rv)
-		goto free_port;
+		goto free_name;
 
 	port->vio.debug = vcc_dbg_vio;
 	vcc_ldc_cfg.debug = vcc_dbg_ldc;
 
 	rv = vio_ldc_alloc(&port->vio, &vcc_ldc_cfg, port);
 	if (rv)
-		goto free_port;
+		goto free_name;
 
 	spin_lock_init(&port->lock);
 
@@ -623,6 +627,11 @@
 		goto unreg_tty;
 	}
 	port->domain = kstrdup(domain, GFP_KERNEL);
+	if (!port->domain) {
+		rv = -ENOMEM;
+		goto unreg_tty;
+	}
+
 
 	mdesc_release(hp);
 
@@ -652,8 +661,9 @@
 	vcc_table_remove(port->index);
 free_ldc:
 	vio_ldc_free(&port->vio);
-free_port:
+free_name:
 	kfree(name);
+free_port:
 	kfree(port);
 
 	return rv;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/vt/keyboard.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/vt/keyboard.c
@@ -324,13 +324,13 @@
 static void put_queue(struct vc_data *vc, int ch)
 {
 	tty_insert_flip_char(&vc->port, ch, 0);
-	tty_schedule_flip(&vc->port);
+	tty_flip_buffer_push(&vc->port);
 }
 
 static void puts_queue(struct vc_data *vc, const char *cp)
 {
 	tty_insert_flip_string(&vc->port, cp, strlen(cp));
-	tty_schedule_flip(&vc->port);
+	tty_flip_buffer_push(&vc->port);
 }
 
 static void applkey(struct vc_data *vc, int key, char mode)
@@ -584,7 +584,7 @@
 static void fn_send_intr(struct vc_data *vc)
 {
 	tty_insert_flip_char(&vc->port, 0, TTY_BREAK);
-	tty_schedule_flip(&vc->port);
+	tty_flip_buffer_push(&vc->port);
 }
 
 static void fn_scroll_forw(struct vc_data *vc)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/vt/vc_screen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/vt/vc_screen.c
@@ -386,10 +386,6 @@
 
 	uni_mode = use_unicode(inode);
 	attr = use_attributes(inode);
-	ret = -ENXIO;
-	vc = vcs_vc(inode, &viewed);
-	if (!vc)
-		goto unlock_out;
 
 	ret = -EINVAL;
 	if (pos < 0)
@@ -407,16 +403,20 @@
 		unsigned int this_round, skip = 0;
 		int size;
 
+		vc = vcs_vc(inode, &viewed);
+		if (!vc) {
+			ret = -ENXIO;
+			break;
+		}
+
 		/* Check whether we are above size each round,
 		 * as copy_to_user at the end of this loop
 		 * could sleep.
 		 */
 		size = vcs_size(vc, attr, uni_mode);
 		if (size < 0) {
-			if (read)
-				break;
 			ret = size;
-			goto unlock_out;
+			break;
 		}
 		if (pos >= size)
 			break;
@@ -656,10 +656,17 @@
 			}
 		}
 
-		/* The vcs_size might have changed while we slept to grab
-		 * the user buffer, so recheck.
+		/* The vc might have been freed or vcs_size might have changed
+		 * while we slept to grab the user buffer, so recheck.
 		 * Return data written up to now on failure.
 		 */
+		vc = vcs_vc(inode, &viewed);
+		if (!vc) {
+			if (written)
+				break;
+			ret = -ENXIO;
+			goto unlock_out;
+		}
 		size = vcs_size(vc, attr, false);
 		if (size < 0) {
 			if (written)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/vt/vt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/vt/vt.c
@@ -344,7 +344,7 @@
 	/* allocate everything in one go */
 	memsize = cols * rows * sizeof(char32_t);
 	memsize += rows * sizeof(char32_t *);
-	p = vmalloc(memsize);
+	p = vzalloc(memsize);
 	if (!p)
 		return NULL;
 
@@ -398,7 +398,7 @@
 		char32_t *ln = uniscr->lines[vc->state.y];
 		unsigned int x = vc->state.x, cols = vc->vc_cols;
 
-		memcpy(&ln[x], &ln[x + nr], (cols - x - nr) * sizeof(*ln));
+		memmove(&ln[x], &ln[x + nr], (cols - x - nr) * sizeof(*ln));
 		memset32(&ln[cols - nr], ' ', nr);
 	}
 }
@@ -855,7 +855,7 @@
 	unsigned short *p = (unsigned short *) vc->vc_pos;
 
 	vc_uniscr_delete(vc, nr);
-	scr_memcpyw(p, p + nr, (vc->vc_cols - vc->state.x - nr) * 2);
+	scr_memmovew(p, p + nr, (vc->vc_cols - vc->state.x - nr) * 2);
 	scr_memsetw(p + vc->vc_cols - vc->state.x - nr, vc->vc_video_erase_char,
 			nr * 2);
 	vc->vc_need_wrap = 0;
@@ -1833,7 +1833,7 @@
 static void respond_string(const char *p, size_t len, struct tty_port *port)
 {
 	tty_insert_flip_string(port, p, len);
-	tty_schedule_flip(port);
+	tty_flip_buffer_push(port);
 }
 
 static void cursor_report(struct vc_data *vc, struct tty_struct *tty)
@@ -2515,7 +2515,7 @@
 		}
 		return;
 	case EScsiignore:
-		if (c >= 20 && c <= 0x3f)
+		if (c >= 0x20 && c <= 0x3f)
 			return;
 		vc->vc_state = ESnormal;
 		return;
@@ -4594,7 +4594,7 @@
 	int c;
 
 	if (op->data) {
-		font.data = kmalloc(max_font_size, GFP_KERNEL);
+		font.data = kzalloc(max_font_size, GFP_KERNEL);
 		if (!font.data)
 			return -ENOMEM;
 	} else
@@ -4662,9 +4662,11 @@
 	console_lock();
 	if (vc->vc_mode != KD_TEXT)
 		rc = -EINVAL;
-	else if (vc->vc_sw->con_font_set)
+	else if (vc->vc_sw->con_font_set) {
+		if (vc_is_sel(vc))
+			clear_selection();
 		rc = vc->vc_sw->con_font_set(vc, &font, op->flags);
-	else
+	} else
 		rc = -ENOSYS;
 	console_unlock();
 	kfree(font.data);
@@ -4691,9 +4693,11 @@
 		console_unlock();
 		return -EINVAL;
 	}
-	if (vc->vc_sw->con_font_default)
+	if (vc->vc_sw->con_font_default) {
+		if (vc_is_sel(vc))
+			clear_selection();
 		rc = vc->vc_sw->con_font_default(vc, &font, s);
-	else
+	} else
 		rc = -ENOSYS;
 	console_unlock();
 	if (!rc) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/tty/vt/vt_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/tty/vt/vt_ioctl.c
@@ -599,8 +599,8 @@
 	if (vsa.console == 0 || vsa.console > MAX_NR_CONSOLES)
 		return -ENXIO;
 
-	vsa.console = array_index_nospec(vsa.console, MAX_NR_CONSOLES + 1);
 	vsa.console--;
+	vsa.console = array_index_nospec(vsa.console, MAX_NR_CONSOLES);
 	console_lock();
 	ret = vc_allocate(vsa.console);
 	if (ret) {
@@ -845,6 +845,7 @@
 			return -ENXIO;
 
 		arg--;
+		arg = array_index_nospec(arg, MAX_NR_CONSOLES);
 		console_lock();
 		ret = vc_allocate(arg);
 		console_unlock();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/Kconfig
@@ -2,6 +2,7 @@
 menuconfig UIO
 	tristate "Userspace I/O drivers"
 	depends on MMU
+	select DMA_SHARED_BUFFER
 	help
 	  Enable this to allow the userspace driver core code to be
 	  built.  This code allows userspace programs easy access to
@@ -166,6 +167,28 @@
 
 	  If you compile this as a module, it will be called uio_hv_generic.
 
+config UIO_XILINX_APM
+	tristate "Xilinx AXI Performance Monitor driver"
+	depends on MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP
+	help
+	  This driver is developed for AXI Performance Monitor IP, designed to
+	  monitor AXI4 traffic for performance analysis of AXI bus in the
+	  system. Driver maps HW registers and parameters to userspace.
+
+	  To compile this driver as a module, choose M here; the module
+	  will be called uio_xilinx_apm.
+
+config UIO_XILINX_AI_ENGINE
+	tristate "Xilinx AI Engine driver"
+	select IRQ_SIM
+	select UIO_DMEM_GENIRQ
+	select UIO_PDRV_GENIRQ
+	help
+	  The driver for Xilinx AI Engine that utilizes the uio_dmem_genirq.
+	  The userspace library will use this to interact with the AI Engine
+	  hardware, as well as for the memory allocation.
+	  Say 'y' only for platforms with the AI Engine IP.
+
 config UIO_DFL
 	tristate "Generic driver for DFL (Device Feature List) bus"
 	depends on FPGA_DFL
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/Makefile
@@ -1,4 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
+uio-y := uio_core.o uio_dmabuf.o
+
 obj-$(CONFIG_UIO)	+= uio.o
 obj-$(CONFIG_UIO_CIF)	+= uio_cif.o
 obj-$(CONFIG_UIO_PDRV_GENIRQ)	+= uio_pdrv_genirq.o
@@ -9,6 +11,8 @@
 obj-$(CONFIG_UIO_NETX)	+= uio_netx.o
 obj-$(CONFIG_UIO_PRUSS)         += uio_pruss.o
 obj-$(CONFIG_UIO_MF624)         += uio_mf624.o
+obj-$(CONFIG_UIO_XILINX_APM)	+= uio_xilinx_apm.o
 obj-$(CONFIG_UIO_FSL_ELBC_GPCM)	+= uio_fsl_elbc_gpcm.o
 obj-$(CONFIG_UIO_HV_GENERIC)	+= uio_hv_generic.o
+obj-$(CONFIG_UIO_XILINX_AI_ENGINE) += uio_xilinx_ai_engine.o
 obj-$(CONFIG_UIO_DFL)	+= uio_dfl.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_core.c
@@ -0,0 +1,1128 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * drivers/uio/uio.c
+ *
+ * Copyright(C) 2005, Benedikt Spranger <b.spranger@linutronix.de>
+ * Copyright(C) 2005, Thomas Gleixner <tglx@linutronix.de>
+ * Copyright(C) 2006, Hans J. Koch <hjk@hansjkoch.de>
+ * Copyright(C) 2006, Greg Kroah-Hartman <greg@kroah.com>
+ *
+ * Userspace IO
+ *
+ * Base Functions
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/poll.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/idr.h>
+#include <linux/sched/signal.h>
+#include <linux/string.h>
+#include <linux/kobject.h>
+#include <linux/cdev.h>
+#include <linux/uio_driver.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+
+#include <uapi/linux/uio/uio.h>
+
+#include "uio_dmabuf.h"
+
+#define UIO_MAX_DEVICES		(1U << MINORBITS)
+
+static int uio_major;
+static struct cdev *uio_cdev;
+static DEFINE_IDR(uio_idr);
+static const struct file_operations uio_fops;
+
+/* Protect idr accesses */
+static DEFINE_MUTEX(minor_lock);
+
+/*
+ * attributes
+ */
+
+struct uio_map {
+	struct kobject kobj;
+	struct uio_mem *mem;
+};
+#define to_map(map) container_of(map, struct uio_map, kobj)
+
+static ssize_t map_name_show(struct uio_mem *mem, char *buf)
+{
+	if (unlikely(!mem->name))
+		mem->name = "";
+
+	return sprintf(buf, "%s\n", mem->name);
+}
+
+static ssize_t map_addr_show(struct uio_mem *mem, char *buf)
+{
+	return sprintf(buf, "%pa\n", &mem->addr);
+}
+
+static ssize_t map_size_show(struct uio_mem *mem, char *buf)
+{
+	return sprintf(buf, "%pa\n", &mem->size);
+}
+
+static ssize_t map_offset_show(struct uio_mem *mem, char *buf)
+{
+	return sprintf(buf, "0x%llx\n", (unsigned long long)mem->offs);
+}
+
+struct map_sysfs_entry {
+	struct attribute attr;
+	ssize_t (*show)(struct uio_mem *, char *);
+	ssize_t (*store)(struct uio_mem *, const char *, size_t);
+};
+
+static struct map_sysfs_entry name_attribute =
+	__ATTR(name, S_IRUGO, map_name_show, NULL);
+static struct map_sysfs_entry addr_attribute =
+	__ATTR(addr, S_IRUGO, map_addr_show, NULL);
+static struct map_sysfs_entry size_attribute =
+	__ATTR(size, S_IRUGO, map_size_show, NULL);
+static struct map_sysfs_entry offset_attribute =
+	__ATTR(offset, S_IRUGO, map_offset_show, NULL);
+
+static struct attribute *attrs[] = {
+	&name_attribute.attr,
+	&addr_attribute.attr,
+	&size_attribute.attr,
+	&offset_attribute.attr,
+	NULL,	/* need to NULL terminate the list of attributes */
+};
+
+static void map_release(struct kobject *kobj)
+{
+	struct uio_map *map = to_map(kobj);
+	kfree(map);
+}
+
+static ssize_t map_type_show(struct kobject *kobj, struct attribute *attr,
+			     char *buf)
+{
+	struct uio_map *map = to_map(kobj);
+	struct uio_mem *mem = map->mem;
+	struct map_sysfs_entry *entry;
+
+	entry = container_of(attr, struct map_sysfs_entry, attr);
+
+	if (!entry->show)
+		return -EIO;
+
+	return entry->show(mem, buf);
+}
+
+static const struct sysfs_ops map_sysfs_ops = {
+	.show = map_type_show,
+};
+
+static struct kobj_type map_attr_type = {
+	.release	= map_release,
+	.sysfs_ops	= &map_sysfs_ops,
+	.default_attrs	= attrs,
+};
+
+struct uio_portio {
+	struct kobject kobj;
+	struct uio_port *port;
+};
+#define to_portio(portio) container_of(portio, struct uio_portio, kobj)
+
+static ssize_t portio_name_show(struct uio_port *port, char *buf)
+{
+	if (unlikely(!port->name))
+		port->name = "";
+
+	return sprintf(buf, "%s\n", port->name);
+}
+
+static ssize_t portio_start_show(struct uio_port *port, char *buf)
+{
+	return sprintf(buf, "0x%lx\n", port->start);
+}
+
+static ssize_t portio_size_show(struct uio_port *port, char *buf)
+{
+	return sprintf(buf, "0x%lx\n", port->size);
+}
+
+static ssize_t portio_porttype_show(struct uio_port *port, char *buf)
+{
+	const char *porttypes[] = {"none", "x86", "gpio", "other"};
+
+	if ((port->porttype < 0) || (port->porttype > UIO_PORT_OTHER))
+		return -EINVAL;
+
+	return sprintf(buf, "port_%s\n", porttypes[port->porttype]);
+}
+
+struct portio_sysfs_entry {
+	struct attribute attr;
+	ssize_t (*show)(struct uio_port *, char *);
+	ssize_t (*store)(struct uio_port *, const char *, size_t);
+};
+
+static struct portio_sysfs_entry portio_name_attribute =
+	__ATTR(name, S_IRUGO, portio_name_show, NULL);
+static struct portio_sysfs_entry portio_start_attribute =
+	__ATTR(start, S_IRUGO, portio_start_show, NULL);
+static struct portio_sysfs_entry portio_size_attribute =
+	__ATTR(size, S_IRUGO, portio_size_show, NULL);
+static struct portio_sysfs_entry portio_porttype_attribute =
+	__ATTR(porttype, S_IRUGO, portio_porttype_show, NULL);
+
+static struct attribute *portio_attrs[] = {
+	&portio_name_attribute.attr,
+	&portio_start_attribute.attr,
+	&portio_size_attribute.attr,
+	&portio_porttype_attribute.attr,
+	NULL,
+};
+
+static void portio_release(struct kobject *kobj)
+{
+	struct uio_portio *portio = to_portio(kobj);
+	kfree(portio);
+}
+
+static ssize_t portio_type_show(struct kobject *kobj, struct attribute *attr,
+			     char *buf)
+{
+	struct uio_portio *portio = to_portio(kobj);
+	struct uio_port *port = portio->port;
+	struct portio_sysfs_entry *entry;
+
+	entry = container_of(attr, struct portio_sysfs_entry, attr);
+
+	if (!entry->show)
+		return -EIO;
+
+	return entry->show(port, buf);
+}
+
+static const struct sysfs_ops portio_sysfs_ops = {
+	.show = portio_type_show,
+};
+
+static struct kobj_type portio_attr_type = {
+	.release	= portio_release,
+	.sysfs_ops	= &portio_sysfs_ops,
+	.default_attrs	= portio_attrs,
+};
+
+static ssize_t name_show(struct device *dev,
+			 struct device_attribute *attr, char *buf)
+{
+	struct uio_device *idev = dev_get_drvdata(dev);
+	int ret;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info) {
+		ret = -EINVAL;
+		dev_err(dev, "the device has been unregistered\n");
+		goto out;
+	}
+
+	ret = sprintf(buf, "%s\n", idev->info->name);
+
+out:
+	mutex_unlock(&idev->info_lock);
+	return ret;
+}
+static DEVICE_ATTR_RO(name);
+
+static ssize_t version_show(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	struct uio_device *idev = dev_get_drvdata(dev);
+	int ret;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info) {
+		ret = -EINVAL;
+		dev_err(dev, "the device has been unregistered\n");
+		goto out;
+	}
+
+	ret = sprintf(buf, "%s\n", idev->info->version);
+
+out:
+	mutex_unlock(&idev->info_lock);
+	return ret;
+}
+static DEVICE_ATTR_RO(version);
+
+static ssize_t event_show(struct device *dev,
+			  struct device_attribute *attr, char *buf)
+{
+	struct uio_device *idev = dev_get_drvdata(dev);
+	return sprintf(buf, "%u\n", (unsigned int)atomic_read(&idev->event));
+}
+static DEVICE_ATTR_RO(event);
+
+static struct attribute *uio_attrs[] = {
+	&dev_attr_name.attr,
+	&dev_attr_version.attr,
+	&dev_attr_event.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(uio);
+
+/* UIO class infrastructure */
+static struct class uio_class = {
+	.name = "uio",
+	.dev_groups = uio_groups,
+};
+
+static bool uio_class_registered;
+
+/*
+ * device functions
+ */
+static int uio_dev_add_attributes(struct uio_device *idev)
+{
+	int ret;
+	int mi, pi;
+	int map_found = 0;
+	int portio_found = 0;
+	struct uio_mem *mem;
+	struct uio_map *map;
+	struct uio_port *port;
+	struct uio_portio *portio;
+
+	for (mi = 0; mi < MAX_UIO_MAPS; mi++) {
+		mem = &idev->info->mem[mi];
+		if (mem->size == 0)
+			break;
+		if (!map_found) {
+			map_found = 1;
+			idev->map_dir = kobject_create_and_add("maps",
+							&idev->dev.kobj);
+			if (!idev->map_dir) {
+				ret = -ENOMEM;
+				goto err_map;
+			}
+		}
+		map = kzalloc(sizeof(*map), GFP_KERNEL);
+		if (!map) {
+			ret = -ENOMEM;
+			goto err_map;
+		}
+		kobject_init(&map->kobj, &map_attr_type);
+		map->mem = mem;
+		mem->map = map;
+		ret = kobject_add(&map->kobj, idev->map_dir, "map%d", mi);
+		if (ret)
+			goto err_map_kobj;
+		ret = kobject_uevent(&map->kobj, KOBJ_ADD);
+		if (ret)
+			goto err_map_kobj;
+	}
+
+	for (pi = 0; pi < MAX_UIO_PORT_REGIONS; pi++) {
+		port = &idev->info->port[pi];
+		if (port->size == 0)
+			break;
+		if (!portio_found) {
+			portio_found = 1;
+			idev->portio_dir = kobject_create_and_add("portio",
+							&idev->dev.kobj);
+			if (!idev->portio_dir) {
+				ret = -ENOMEM;
+				goto err_portio;
+			}
+		}
+		portio = kzalloc(sizeof(*portio), GFP_KERNEL);
+		if (!portio) {
+			ret = -ENOMEM;
+			goto err_portio;
+		}
+		kobject_init(&portio->kobj, &portio_attr_type);
+		portio->port = port;
+		port->portio = portio;
+		ret = kobject_add(&portio->kobj, idev->portio_dir,
+							"port%d", pi);
+		if (ret)
+			goto err_portio_kobj;
+		ret = kobject_uevent(&portio->kobj, KOBJ_ADD);
+		if (ret)
+			goto err_portio_kobj;
+	}
+
+	return 0;
+
+err_portio:
+	pi--;
+err_portio_kobj:
+	for (; pi >= 0; pi--) {
+		port = &idev->info->port[pi];
+		portio = port->portio;
+		kobject_put(&portio->kobj);
+	}
+	kobject_put(idev->portio_dir);
+err_map:
+	mi--;
+err_map_kobj:
+	for (; mi >= 0; mi--) {
+		mem = &idev->info->mem[mi];
+		map = mem->map;
+		kobject_put(&map->kobj);
+	}
+	kobject_put(idev->map_dir);
+	dev_err(&idev->dev, "error creating sysfs files (%d)\n", ret);
+	return ret;
+}
+
+static void uio_dev_del_attributes(struct uio_device *idev)
+{
+	int i;
+	struct uio_mem *mem;
+	struct uio_port *port;
+
+	for (i = 0; i < MAX_UIO_MAPS; i++) {
+		mem = &idev->info->mem[i];
+		if (mem->size == 0)
+			break;
+		kobject_put(&mem->map->kobj);
+	}
+	kobject_put(idev->map_dir);
+
+	for (i = 0; i < MAX_UIO_PORT_REGIONS; i++) {
+		port = &idev->info->port[i];
+		if (port->size == 0)
+			break;
+		kobject_put(&port->portio->kobj);
+	}
+	kobject_put(idev->portio_dir);
+}
+
+static int uio_get_minor(struct uio_device *idev)
+{
+	int retval;
+
+	mutex_lock(&minor_lock);
+	retval = idr_alloc(&uio_idr, idev, 0, UIO_MAX_DEVICES, GFP_KERNEL);
+	if (retval >= 0) {
+		idev->minor = retval;
+		retval = 0;
+	} else if (retval == -ENOSPC) {
+		dev_err(&idev->dev, "too many uio devices\n");
+		retval = -EINVAL;
+	}
+	mutex_unlock(&minor_lock);
+	return retval;
+}
+
+static void uio_free_minor(unsigned long minor)
+{
+	mutex_lock(&minor_lock);
+	idr_remove(&uio_idr, minor);
+	mutex_unlock(&minor_lock);
+}
+
+/**
+ * uio_event_notify - trigger an interrupt event
+ * @info: UIO device capabilities
+ */
+void uio_event_notify(struct uio_info *info)
+{
+	struct uio_device *idev = info->uio_dev;
+
+	atomic_inc(&idev->event);
+	wake_up_interruptible(&idev->wait);
+	kill_fasync(&idev->async_queue, SIGIO, POLL_IN);
+}
+EXPORT_SYMBOL_GPL(uio_event_notify);
+
+/**
+ * uio_interrupt - hardware interrupt handler
+ * @irq: IRQ number, can be UIO_IRQ_CYCLIC for cyclic timer
+ * @dev_id: Pointer to the devices uio_device structure
+ */
+static irqreturn_t uio_interrupt(int irq, void *dev_id)
+{
+	struct uio_device *idev = (struct uio_device *)dev_id;
+	irqreturn_t ret;
+
+	ret = idev->info->handler(irq, idev->info);
+	if (ret == IRQ_HANDLED)
+		uio_event_notify(idev->info);
+
+	return ret;
+}
+
+struct uio_listener {
+	struct uio_device *dev;
+	s32 event_count;
+	struct list_head dbufs;
+	struct mutex dbufs_lock; /* protect @dbufs */
+};
+
+static int uio_open(struct inode *inode, struct file *filep)
+{
+	struct uio_device *idev;
+	struct uio_listener *listener;
+	int ret = 0;
+
+	mutex_lock(&minor_lock);
+	idev = idr_find(&uio_idr, iminor(inode));
+	if (!idev) {
+		ret = -ENODEV;
+		mutex_unlock(&minor_lock);
+		goto out;
+	}
+	get_device(&idev->dev);
+	mutex_unlock(&minor_lock);
+
+	if (!try_module_get(idev->owner)) {
+		ret = -ENODEV;
+		goto err_module_get;
+	}
+
+	listener = kmalloc(sizeof(*listener), GFP_KERNEL);
+	if (!listener) {
+		ret = -ENOMEM;
+		goto err_alloc_listener;
+	}
+
+	listener->dev = idev;
+	listener->event_count = atomic_read(&idev->event);
+	filep->private_data = listener;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info) {
+		mutex_unlock(&idev->info_lock);
+		ret = -EINVAL;
+		goto err_infoopen;
+	}
+
+	if (idev->info->open)
+		ret = idev->info->open(idev->info, inode);
+	mutex_unlock(&idev->info_lock);
+	if (ret)
+		goto err_infoopen;
+
+	INIT_LIST_HEAD(&listener->dbufs);
+	mutex_init(&listener->dbufs_lock);
+
+	return 0;
+
+err_infoopen:
+	kfree(listener);
+
+err_alloc_listener:
+	module_put(idev->owner);
+
+err_module_get:
+	put_device(&idev->dev);
+
+out:
+	return ret;
+}
+
+static int uio_fasync(int fd, struct file *filep, int on)
+{
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+
+	return fasync_helper(fd, filep, on, &idev->async_queue);
+}
+
+static int uio_release(struct inode *inode, struct file *filep)
+{
+	int ret = 0;
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+
+	ret = uio_dmabuf_cleanup(idev, &listener->dbufs, &listener->dbufs_lock);
+	if (ret)
+		dev_err(&idev->dev, "failed to clean up the dma bufs\n");
+
+	mutex_lock(&idev->info_lock);
+	if (idev->info && idev->info->release)
+		ret = idev->info->release(idev->info, inode);
+	mutex_unlock(&idev->info_lock);
+
+	module_put(idev->owner);
+	kfree(listener);
+	put_device(&idev->dev);
+	return ret;
+}
+
+static __poll_t uio_poll(struct file *filep, poll_table *wait)
+{
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+	__poll_t ret = 0;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info || !idev->info->irq)
+		ret = -EIO;
+	mutex_unlock(&idev->info_lock);
+
+	if (ret)
+		return ret;
+
+	poll_wait(filep, &idev->wait, wait);
+	if (listener->event_count != atomic_read(&idev->event))
+		return EPOLLIN | EPOLLRDNORM;
+	return 0;
+}
+
+static ssize_t uio_read(struct file *filep, char __user *buf,
+			size_t count, loff_t *ppos)
+{
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+	DECLARE_WAITQUEUE(wait, current);
+	ssize_t retval = 0;
+	s32 event_count;
+
+	if (count != sizeof(s32))
+		return -EINVAL;
+
+	add_wait_queue(&idev->wait, &wait);
+
+	do {
+		mutex_lock(&idev->info_lock);
+		if (!idev->info || !idev->info->irq) {
+			retval = -EIO;
+			mutex_unlock(&idev->info_lock);
+			break;
+		}
+		mutex_unlock(&idev->info_lock);
+
+		set_current_state(TASK_INTERRUPTIBLE);
+
+		event_count = atomic_read(&idev->event);
+		if (event_count != listener->event_count) {
+			__set_current_state(TASK_RUNNING);
+			if (copy_to_user(buf, &event_count, count))
+				retval = -EFAULT;
+			else {
+				listener->event_count = event_count;
+				retval = count;
+			}
+			break;
+		}
+
+		if (filep->f_flags & O_NONBLOCK) {
+			retval = -EAGAIN;
+			break;
+		}
+
+		if (signal_pending(current)) {
+			retval = -ERESTARTSYS;
+			break;
+		}
+		schedule();
+	} while (1);
+
+	__set_current_state(TASK_RUNNING);
+	remove_wait_queue(&idev->wait, &wait);
+
+	return retval;
+}
+
+static ssize_t uio_write(struct file *filep, const char __user *buf,
+			size_t count, loff_t *ppos)
+{
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+	ssize_t retval;
+	s32 irq_on;
+
+	if (count != sizeof(s32))
+		return -EINVAL;
+
+	if (copy_from_user(&irq_on, buf, count))
+		return -EFAULT;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info) {
+		retval = -EINVAL;
+		goto out;
+	}
+
+	if (!idev->info->irq) {
+		retval = -EIO;
+		goto out;
+	}
+
+	if (!idev->info->irqcontrol) {
+		retval = -ENOSYS;
+		goto out;
+	}
+
+	retval = idev->info->irqcontrol(idev->info, irq_on);
+
+out:
+	mutex_unlock(&idev->info_lock);
+	return retval ? retval : sizeof(s32);
+}
+
+static long uio_ioctl(struct file *filep, unsigned int cmd, unsigned long arg)
+{
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+	long ret;
+
+	if (!idev->info)
+		return -EIO;
+
+	switch (cmd) {
+	case UIO_IOC_MAP_DMABUF:
+		ret = uio_dmabuf_map(idev, &listener->dbufs,
+				     &listener->dbufs_lock, (void __user *)arg);
+		break;
+	case UIO_IOC_UNMAP_DMABUF:
+		ret = uio_dmabuf_unmap(idev, &listener->dbufs,
+				       &listener->dbufs_lock,
+				       (void __user *)arg);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+static int uio_find_mem_index(struct vm_area_struct *vma)
+{
+	struct uio_device *idev = vma->vm_private_data;
+
+	if (vma->vm_pgoff < MAX_UIO_MAPS) {
+		if (idev->info->mem[vma->vm_pgoff].size == 0)
+			return -1;
+		return (int)vma->vm_pgoff;
+	}
+	return -1;
+}
+
+static vm_fault_t uio_vma_fault(struct vm_fault *vmf)
+{
+	struct uio_device *idev = vmf->vma->vm_private_data;
+	struct page *page;
+	unsigned long offset;
+	void *addr;
+	vm_fault_t ret = 0;
+	int mi;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info) {
+		ret = VM_FAULT_SIGBUS;
+		goto out;
+	}
+
+	mi = uio_find_mem_index(vmf->vma);
+	if (mi < 0) {
+		ret = VM_FAULT_SIGBUS;
+		goto out;
+	}
+
+	/*
+	 * We need to subtract mi because userspace uses offset = N*PAGE_SIZE
+	 * to use mem[N].
+	 */
+	offset = (vmf->pgoff - mi) << PAGE_SHIFT;
+
+	addr = (void *)(unsigned long)idev->info->mem[mi].addr + offset;
+	if (idev->info->mem[mi].memtype == UIO_MEM_LOGICAL)
+		page = virt_to_page(addr);
+	else
+		page = vmalloc_to_page(addr);
+	get_page(page);
+	vmf->page = page;
+
+out:
+	mutex_unlock(&idev->info_lock);
+
+	return ret;
+}
+
+static const struct vm_operations_struct uio_logical_vm_ops = {
+	.fault = uio_vma_fault,
+};
+
+static int uio_mmap_logical(struct vm_area_struct *vma)
+{
+	vma->vm_flags |= VM_DONTEXPAND | VM_DONTDUMP;
+	vma->vm_ops = &uio_logical_vm_ops;
+	return 0;
+}
+
+static const struct vm_operations_struct uio_physical_vm_ops = {
+#ifdef CONFIG_HAVE_IOREMAP_PROT
+	.access = generic_access_phys,
+#endif
+};
+
+static int uio_mmap_physical(struct vm_area_struct *vma)
+{
+	struct uio_device *idev = vma->vm_private_data;
+	int mi = uio_find_mem_index(vma);
+	struct uio_mem *mem;
+
+	if (mi < 0)
+		return -EINVAL;
+	mem = idev->info->mem + mi;
+
+	if (mem->addr & ~PAGE_MASK)
+		return -ENODEV;
+	if (vma->vm_end - vma->vm_start > mem->size)
+		return -EINVAL;
+
+	vma->vm_ops = &uio_physical_vm_ops;
+	if (idev->info->mem[mi].memtype == UIO_MEM_PHYS)
+		vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+
+	/*
+	 * We cannot use the vm_iomap_memory() helper here,
+	 * because vma->vm_pgoff is the map index we looked
+	 * up above in uio_find_mem_index(), rather than an
+	 * actual page offset into the mmap.
+	 *
+	 * So we just do the physical mmap without a page
+	 * offset.
+	 */
+	return remap_pfn_range(vma,
+			       vma->vm_start,
+			       mem->addr >> PAGE_SHIFT,
+			       vma->vm_end - vma->vm_start,
+			       vma->vm_page_prot);
+}
+
+static int uio_mmap(struct file *filep, struct vm_area_struct *vma)
+{
+	struct uio_listener *listener = filep->private_data;
+	struct uio_device *idev = listener->dev;
+	int mi;
+	unsigned long requested_pages, actual_pages;
+	int ret = 0;
+
+	if (vma->vm_end < vma->vm_start)
+		return -EINVAL;
+
+	vma->vm_private_data = idev;
+
+	mutex_lock(&idev->info_lock);
+	if (!idev->info) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	mi = uio_find_mem_index(vma);
+	if (mi < 0) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	requested_pages = vma_pages(vma);
+	actual_pages = ((idev->info->mem[mi].addr & ~PAGE_MASK)
+			+ idev->info->mem[mi].size + PAGE_SIZE -1) >> PAGE_SHIFT;
+	if (requested_pages > actual_pages) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (idev->info->mmap) {
+		ret = idev->info->mmap(idev->info, vma);
+		goto out;
+	}
+
+	switch (idev->info->mem[mi].memtype) {
+	case UIO_MEM_IOVA:
+	case UIO_MEM_PHYS:
+		ret = uio_mmap_physical(vma);
+		break;
+	case UIO_MEM_LOGICAL:
+	case UIO_MEM_VIRTUAL:
+		ret = uio_mmap_logical(vma);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+ out:
+	mutex_unlock(&idev->info_lock);
+	return ret;
+}
+
+static const struct file_operations uio_fops = {
+	.owner		= THIS_MODULE,
+	.open		= uio_open,
+	.release	= uio_release,
+	.read		= uio_read,
+	.write		= uio_write,
+	.mmap		= uio_mmap,
+	.poll		= uio_poll,
+	.unlocked_ioctl	= uio_ioctl,
+	.fasync		= uio_fasync,
+	.llseek		= noop_llseek,
+};
+
+static int uio_major_init(void)
+{
+	static const char name[] = "uio";
+	struct cdev *cdev = NULL;
+	dev_t uio_dev = 0;
+	int result;
+
+	result = alloc_chrdev_region(&uio_dev, 0, UIO_MAX_DEVICES, name);
+	if (result)
+		goto out;
+
+	result = -ENOMEM;
+	cdev = cdev_alloc();
+	if (!cdev)
+		goto out_unregister;
+
+	cdev->owner = THIS_MODULE;
+	cdev->ops = &uio_fops;
+	kobject_set_name(&cdev->kobj, "%s", name);
+
+	result = cdev_add(cdev, uio_dev, UIO_MAX_DEVICES);
+	if (result)
+		goto out_put;
+
+	uio_major = MAJOR(uio_dev);
+	uio_cdev = cdev;
+	return 0;
+out_put:
+	kobject_put(&cdev->kobj);
+out_unregister:
+	unregister_chrdev_region(uio_dev, UIO_MAX_DEVICES);
+out:
+	return result;
+}
+
+static void uio_major_cleanup(void)
+{
+	unregister_chrdev_region(MKDEV(uio_major, 0), UIO_MAX_DEVICES);
+	cdev_del(uio_cdev);
+}
+
+static int init_uio_class(void)
+{
+	int ret;
+
+	/* This is the first time in here, set everything up properly */
+	ret = uio_major_init();
+	if (ret)
+		goto exit;
+
+	ret = class_register(&uio_class);
+	if (ret) {
+		printk(KERN_ERR "class_register failed for uio\n");
+		goto err_class_register;
+	}
+
+	uio_class_registered = true;
+
+	return 0;
+
+err_class_register:
+	uio_major_cleanup();
+exit:
+	return ret;
+}
+
+static void release_uio_class(void)
+{
+	uio_class_registered = false;
+	class_unregister(&uio_class);
+	uio_major_cleanup();
+}
+
+static void uio_device_release(struct device *dev)
+{
+	struct uio_device *idev = dev_get_drvdata(dev);
+
+	kfree(idev);
+}
+
+/**
+ * __uio_register_device - register a new userspace IO device
+ * @owner:	module that creates the new device
+ * @parent:	parent device
+ * @info:	UIO device capabilities
+ *
+ * returns zero on success or a negative error code.
+ */
+int __uio_register_device(struct module *owner,
+			  struct device *parent,
+			  struct uio_info *info)
+{
+	struct uio_device *idev;
+	int ret = 0;
+
+	if (!uio_class_registered)
+		return -EPROBE_DEFER;
+
+	if (!parent || !info || !info->name || !info->version)
+		return -EINVAL;
+
+	info->uio_dev = NULL;
+
+	idev = kzalloc(sizeof(*idev), GFP_KERNEL);
+	if (!idev) {
+		return -ENOMEM;
+	}
+
+	idev->owner = owner;
+	idev->info = info;
+	mutex_init(&idev->info_lock);
+	init_waitqueue_head(&idev->wait);
+	atomic_set(&idev->event, 0);
+
+	ret = uio_get_minor(idev);
+	if (ret) {
+		kfree(idev);
+		return ret;
+	}
+
+	device_initialize(&idev->dev);
+	idev->dev.devt = MKDEV(uio_major, idev->minor);
+	idev->dev.class = &uio_class;
+	idev->dev.parent = parent;
+	idev->dev.release = uio_device_release;
+	dev_set_drvdata(&idev->dev, idev);
+
+	ret = dev_set_name(&idev->dev, "uio%d", idev->minor);
+	if (ret)
+		goto err_device_create;
+
+	ret = device_add(&idev->dev);
+	if (ret)
+		goto err_device_create;
+
+	ret = uio_dev_add_attributes(idev);
+	if (ret)
+		goto err_uio_dev_add_attributes;
+
+	info->uio_dev = idev;
+
+	if (info->irq && (info->irq != UIO_IRQ_CUSTOM)) {
+		/*
+		 * Note that we deliberately don't use devm_request_irq
+		 * here. The parent module can unregister the UIO device
+		 * and call pci_disable_msi, which requires that this
+		 * irq has been freed. However, the device may have open
+		 * FDs at the time of unregister and therefore may not be
+		 * freed until they are released.
+		 */
+		ret = request_irq(info->irq, uio_interrupt,
+				  info->irq_flags, info->name, idev);
+		if (ret) {
+			info->uio_dev = NULL;
+			goto err_request_irq;
+		}
+	}
+
+	return 0;
+
+err_request_irq:
+	uio_dev_del_attributes(idev);
+err_uio_dev_add_attributes:
+	device_del(&idev->dev);
+err_device_create:
+	uio_free_minor(idev->minor);
+	put_device(&idev->dev);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(__uio_register_device);
+
+static void devm_uio_unregister_device(struct device *dev, void *res)
+{
+	uio_unregister_device(*(struct uio_info **)res);
+}
+
+/**
+ * __devm_uio_register_device - Resource managed uio_register_device()
+ * @owner:	module that creates the new device
+ * @parent:	parent device
+ * @info:	UIO device capabilities
+ *
+ * returns zero on success or a negative error code.
+ */
+int __devm_uio_register_device(struct module *owner,
+			       struct device *parent,
+			       struct uio_info *info)
+{
+	struct uio_info **ptr;
+	int ret;
+
+	ptr = devres_alloc(devm_uio_unregister_device, sizeof(*ptr),
+			   GFP_KERNEL);
+	if (!ptr)
+		return -ENOMEM;
+
+	*ptr = info;
+	ret = __uio_register_device(owner, parent, info);
+	if (ret) {
+		devres_free(ptr);
+		return ret;
+	}
+
+	devres_add(parent, ptr);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(__devm_uio_register_device);
+
+/**
+ * uio_unregister_device - unregister a industrial IO device
+ * @info:	UIO device capabilities
+ *
+ */
+void uio_unregister_device(struct uio_info *info)
+{
+	struct uio_device *idev;
+	unsigned long minor;
+
+	if (!info || !info->uio_dev)
+		return;
+
+	idev = info->uio_dev;
+	minor = idev->minor;
+
+	mutex_lock(&idev->info_lock);
+	uio_dev_del_attributes(idev);
+
+	if (info->irq && info->irq != UIO_IRQ_CUSTOM)
+		free_irq(info->irq, idev);
+
+	idev->info = NULL;
+	mutex_unlock(&idev->info_lock);
+
+	wake_up_interruptible(&idev->wait);
+	kill_fasync(&idev->async_queue, SIGIO, POLL_HUP);
+
+	uio_free_minor(minor);
+	device_unregister(&idev->dev);
+
+	return;
+}
+EXPORT_SYMBOL_GPL(uio_unregister_device);
+
+static int __init uio_init(void)
+{
+	return init_uio_class();
+}
+
+static void __exit uio_exit(void)
+{
+	release_uio_class();
+	idr_destroy(&uio_idr);
+}
+
+module_init(uio_init)
+module_exit(uio_exit)
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_dmabuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_dmabuf.c
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * DMA buf support for UIO device
+ *
+ */
+
+#include <linux/dma-buf.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/uaccess.h>
+#include <linux/uio_driver.h>
+#include <linux/slab.h>
+
+#include <uapi/linux/uio/uio.h>
+
+#include "uio_dmabuf.h"
+
+struct uio_dmabuf_mem {
+	int dbuf_fd;
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *dbuf_attach;
+	struct sg_table *sgt;
+	enum dma_data_direction dir;
+	struct list_head list;
+};
+
+long uio_dmabuf_map(struct uio_device *dev, struct list_head *dbufs,
+		    struct mutex *dbufs_lock, void __user *user_args)
+{
+	struct uio_dmabuf_args args;
+	struct uio_dmabuf_mem *dbuf_mem;
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *dbuf_attach;
+	enum dma_data_direction dir;
+	struct sg_table *sgt;
+	long ret;
+
+	if (copy_from_user(&args, user_args, sizeof(args))) {
+		ret = -EFAULT;
+		dev_err(dev->dev.parent, "failed to copy from user\n");
+		goto err;
+	}
+
+	dbuf = dma_buf_get(args.dbuf_fd);
+	if (IS_ERR(dbuf)) {
+		dev_err(dev->dev.parent, "failed to get dmabuf\n");
+		return PTR_ERR(dbuf);
+	}
+
+	dbuf_attach = dma_buf_attach(dbuf, dev->dev.parent);
+	if (IS_ERR(dbuf_attach)) {
+		dev_err(dev->dev.parent, "failed to attach dmabuf\n");
+		ret = PTR_ERR(dbuf_attach);
+		goto err_put;
+	}
+
+	switch (args.dir) {
+	case UIO_DMABUF_DIR_BIDIR:
+		dir = DMA_BIDIRECTIONAL;
+		break;
+	case UIO_DMABUF_DIR_TO_DEV:
+		dir = DMA_TO_DEVICE;
+		break;
+	case UIO_DMABUF_DIR_FROM_DEV:
+		dir = DMA_FROM_DEVICE;
+		break;
+	default:
+		/* Not needed with check. Just here for any future change  */
+		dev_err(dev->dev.parent, "invalid direction\n");
+		ret = -EINVAL;
+		goto err_detach;
+	}
+
+	sgt = dma_buf_map_attachment(dbuf_attach, dir);
+	if (IS_ERR(sgt)) {
+		dev_err(dev->dev.parent, "failed to get dmabuf scatterlist\n");
+		ret = PTR_ERR(sgt);
+		goto err_detach;
+	}
+
+	/* Accept only contiguous one */
+	if (sgt->nents != 1) {
+		dma_addr_t next_addr = sg_dma_address(sgt->sgl);
+		struct scatterlist *s;
+		unsigned int i;
+
+		for_each_sg(sgt->sgl, s, sgt->nents, i) {
+			if (!sg_dma_len(s))
+				continue;
+
+			if (sg_dma_address(s) != next_addr) {
+				dev_err(dev->dev.parent,
+					"dmabuf not contiguous\n");
+				ret = -EINVAL;
+				goto err_unmap;
+			}
+
+			next_addr = sg_dma_address(s) + sg_dma_len(s);
+		}
+	}
+
+	dbuf_mem = kzalloc(sizeof(*dbuf_mem), GFP_KERNEL);
+	if (!dbuf_mem) {
+		ret = -ENOMEM;
+		goto err_unmap;
+	}
+
+	dbuf_mem->dbuf_fd = args.dbuf_fd;
+	dbuf_mem->dbuf = dbuf;
+	dbuf_mem->dbuf_attach = dbuf_attach;
+	dbuf_mem->sgt = sgt;
+	dbuf_mem->dir = dir;
+	args.dma_addr = sg_dma_address(sgt->sgl);
+	args.size = dbuf->size;
+
+	if (copy_to_user(user_args, &args, sizeof(args))) {
+		ret = -EFAULT;
+		dev_err(dev->dev.parent, "failed to copy to user\n");
+		goto err_free;
+	}
+
+	mutex_lock(dbufs_lock);
+	list_add(&dbuf_mem->list, dbufs);
+	mutex_unlock(dbufs_lock);
+
+	return 0;
+
+err_free:
+	kfree(dbuf_mem);
+err_unmap:
+	dma_buf_unmap_attachment(dbuf_attach, sgt, dir);
+err_detach:
+	dma_buf_detach(dbuf, dbuf_attach);
+err_put:
+	dma_buf_put(dbuf);
+err:
+	return ret;
+}
+
+long uio_dmabuf_unmap(struct uio_device *dev, struct list_head *dbufs,
+		      struct mutex *dbufs_lock, void __user *user_args)
+
+{
+	struct uio_dmabuf_args args;
+	struct uio_dmabuf_mem *dbuf_mem;
+	long ret;
+
+	if (copy_from_user(&args, user_args, sizeof(args))) {
+		ret = -EFAULT;
+		goto err;
+	}
+
+	mutex_lock(dbufs_lock);
+	list_for_each_entry(dbuf_mem, dbufs, list) {
+		if (dbuf_mem->dbuf_fd == args.dbuf_fd)
+			break;
+	}
+
+	if (dbuf_mem->dbuf_fd != args.dbuf_fd) {
+		dev_err(dev->dev.parent, "failed to find the dmabuf (%d)\n",
+			args.dbuf_fd);
+		ret = -EINVAL;
+		goto err_unlock;
+	}
+	list_del(&dbuf_mem->list);
+	mutex_unlock(dbufs_lock);
+
+	dma_buf_unmap_attachment(dbuf_mem->dbuf_attach, dbuf_mem->sgt,
+				 dbuf_mem->dir);
+	dma_buf_detach(dbuf_mem->dbuf, dbuf_mem->dbuf_attach);
+	dma_buf_put(dbuf_mem->dbuf);
+	kfree(dbuf_mem);
+
+	memset(&args, 0x0, sizeof(args));
+
+	if (copy_to_user(user_args, &args, sizeof(args))) {
+		ret = -EFAULT;
+		goto err;
+	}
+
+	return 0;
+
+err_unlock:
+	mutex_unlock(dbufs_lock);
+err:
+	return ret;
+}
+
+int uio_dmabuf_cleanup(struct uio_device *dev, struct list_head *dbufs,
+		       struct mutex *dbufs_lock)
+{
+	struct uio_dmabuf_mem *dbuf_mem, *next;
+
+	mutex_lock(dbufs_lock);
+	list_for_each_entry_safe(dbuf_mem, next, dbufs, list) {
+		list_del(&dbuf_mem->list);
+		dma_buf_unmap_attachment(dbuf_mem->dbuf_attach, dbuf_mem->sgt,
+					 dbuf_mem->dir);
+		dma_buf_detach(dbuf_mem->dbuf, dbuf_mem->dbuf_attach);
+		dma_buf_put(dbuf_mem->dbuf);
+		kfree(dbuf_mem);
+	}
+	mutex_unlock(dbufs_lock);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_dmabuf.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_dmabuf.h
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ *
+ * DMA buf support for UIO device
+ *
+ */
+
+#ifndef _UIO_DMABUF_H_
+#define _UIO_DMABUF_H_
+
+struct uio_device;
+struct list_head;
+struct mutex;
+
+long uio_dmabuf_map(struct uio_device *dev, struct list_head *dbufs,
+		    struct mutex *dbufs_lock, void __user *user_args);
+long uio_dmabuf_unmap(struct uio_device *dev, struct list_head *dbufs,
+		      struct mutex *dbufs_lock, void __user *user_args);
+
+int uio_dmabuf_cleanup(struct uio_device *dev, struct list_head *dbufs,
+		       struct mutex *dbufs_lock);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_dmem_genirq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_dmem_genirq.c
@@ -110,8 +110,10 @@
 	 * remember the state so we can allow user space to enable it later.
 	 */
 
+	spin_lock(&priv->lock);
 	if (!test_and_set_bit(0, &priv->flags))
 		disable_irq_nosync(irq);
+	spin_unlock(&priv->lock);
 
 	return IRQ_HANDLED;
 }
@@ -125,20 +127,19 @@
 	 * in the interrupt controller, but keep track of the
 	 * state to prevent per-irq depth damage.
 	 *
-	 * Serialize this operation to support multiple tasks.
+	 * Serialize this operation to support multiple tasks and concurrency
+	 * with irq handler on SMP systems.
 	 */
 
 	spin_lock_irqsave(&priv->lock, flags);
 	if (irq_on) {
 		if (test_and_clear_bit(0, &priv->flags))
 			enable_irq(dev_info->irq);
-		spin_unlock_irqrestore(&priv->lock, flags);
 	} else {
-		if (!test_and_set_bit(0, &priv->flags)) {
-			spin_unlock_irqrestore(&priv->lock, flags);
-			disable_irq(dev_info->irq);
-		}
+		if (!test_and_set_bit(0, &priv->flags))
+			disable_irq_nosync(dev_info->irq);
 	}
+	spin_unlock_irqrestore(&priv->lock, flags);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_hv_generic.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_hv_generic.c
@@ -104,10 +104,11 @@
 
 /*
  * Callback from vmbus_event when channel is rescinded.
+ * It is meant for rescind of primary channels only.
  */
 static void hv_uio_rescind(struct vmbus_channel *channel)
 {
-	struct hv_device *hv_dev = channel->primary_channel->device_obj;
+	struct hv_device *hv_dev = channel->device_obj;
 	struct hv_uio_private_data *pdata = hv_get_drvdata(hv_dev);
 
 	/*
@@ -118,6 +119,14 @@
 
 	/* Wake up reader */
 	uio_event_notify(&pdata->info);
+
+	/*
+	 * With rescind callback registered, rescind path will not unregister the device
+	 * from vmbus when the primary channel is rescinded.
+	 * Without it, rescind handling is incomplete and next onoffer msg does not come.
+	 * Unregister the device from vmbus here.
+	 */
+	vmbus_device_unregister(channel->device_obj);
 }
 
 /* Sysfs API to allow mmap of the ring buffers
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_xilinx_ai_engine.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_xilinx_ai_engine.c
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx UIO driver for AI Engine
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ */
+
+#include <linux/debugfs.h>
+#include <linux/irq_sim.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_data/uio_dmem_genirq.h>
+#include <linux/platform_device.h>
+#include <linux/uio_driver.h>
+
+#define DRIVER_NAME "xilinx-aiengine"
+#define XILINX_AI_ENGINE_MAX_IRQ	4
+
+static uint xilinx_ai_engine_mem_cnt = 1;
+module_param_named(mem_cnt, xilinx_ai_engine_mem_cnt, uint, 0444);
+MODULE_PARM_DESC(mem_cnt, "Dynamic memory allocation count (default: 1)");
+
+static uint xilinx_ai_engine_mem_size = 32 * 1024 * 1024;
+module_param_named(mem_size, xilinx_ai_engine_mem_size, uint, 0444);
+MODULE_PARM_DESC(mem_size,
+		 "Dynamic memory allocation size in bytes (default: 32 MB)");
+
+#ifdef CONFIG_DEBUG_FS
+
+static ssize_t xilinx_ai_engine_debugfs_write(struct file *f,
+					      const char __user *buf,
+					      size_t size, loff_t *pos)
+{
+	struct irq_domain *irq_sim_domain = file_inode(f)->i_private;
+	int irq, ret;
+
+	irq = irq_find_mapping(irq_sim_domain, 1);
+	ret = irq_set_irqchip_state(1, IRQCHIP_STATE_PENDING, true);
+	if (ret)
+		return ret;
+
+	return size;
+}
+
+static const struct file_operations debugfs_ops = {
+	.owner = THIS_MODULE,
+	.write = xilinx_ai_engine_debugfs_write,
+};
+
+/**
+ * xilinx_ai_engine_debugfs_init - Initialize the debugfs for irq sim
+ * @pdev: platform device to simulate irq for
+ * @irq_sim_domain: simualated irq
+ *
+ * Initialize the debugfs for irq simulation. This allows to generate
+ * the simulated interrupt from user.
+ *
+ * Return: 0 for success, error code otherwise.
+ */
+static int xilinx_ai_engine_debugfs_init(struct platform_device *pdev,
+					 struct irq_domain *irq_sim_domain)
+{
+	int ret;
+	struct dentry *debugfs_dir, *debugfs_file;
+
+	debugfs_dir = debugfs_create_dir("xilinx-ai-engine", NULL);
+	if (!debugfs_dir)
+		return -ENODEV;
+
+	debugfs_file = debugfs_create_file(dev_name(&pdev->dev), 0644,
+					   debugfs_dir, irq_sim_domain,
+					   &debugfs_ops);
+	if (!debugfs_file) {
+		ret = -ENODEV;
+		goto err_out;
+	}
+
+	return 0;
+
+err_out:
+	debugfs_remove_recursive(debugfs_dir);
+	return ret;
+}
+
+/**
+ * xilinx_ai_engine_simulate_irq - Simulate the irq
+ * @pdev: platform device to simulate irq for
+ *
+ * Simulate the irq so the irq can be generated from user. This is only for
+ * debugging purpose.
+ *
+ * Return: 0 for success, error code otherwise.
+ */
+static int xilinx_ai_engine_simulate_irq(struct platform_device *pdev)
+{
+	struct irq_domain *irq_sim_domain;
+	int ret;
+
+	/*
+	 * Sometimes, the returned base value is 0, so allocate 2 irqs, and
+	 * always use the 2nd one.
+	 */
+	irq_sim_domain = irq_domain_create_sim(NULL, 2);
+	if (IS_ERR(irq_sim_domain)) {
+		ret = PTR_ERR(irq_sim_domain);
+		dev_err(&pdev->dev, "failed to create irq simulation domain");
+		return ret;
+	}
+
+	ret = xilinx_ai_engine_debugfs_init(pdev, irq_sim_domain);
+	if (ret < 0)
+		dev_err(&pdev->dev, "failed create debugfs for sim irq");
+
+	return ret;
+}
+
+#else
+
+static int xilinx_ai_engine_simulate_irq(struct platform_device *pdev)
+{
+	return -ENODEV;
+}
+
+#endif
+
+static int xilinx_ai_engine_mem_index(struct uio_info *info,
+				      struct vm_area_struct *vma)
+{
+	if (vma->vm_pgoff < MAX_UIO_MAPS) {
+		if (info->mem[vma->vm_pgoff].size == 0)
+			return -1;
+		return (int)vma->vm_pgoff;
+	}
+	return -1;
+}
+
+static const struct vm_operations_struct xilinx_ai_engine_vm_ops = {
+#ifdef CONFIG_HAVE_IOREMAP_PROT
+	.access = generic_access_phys,
+#endif
+};
+
+static int xilinx_ai_engine_mmap(struct uio_info *info,
+				 struct vm_area_struct *vma)
+{
+	int mi = xilinx_ai_engine_mem_index(info, vma);
+	struct uio_mem *mem;
+
+	if (mi < 0)
+		return -EINVAL;
+	mem = info->mem + mi;
+
+	if (mem->addr & ~PAGE_MASK)
+		return -ENODEV;
+	if (vma->vm_end - vma->vm_start > mem->size)
+		return -EINVAL;
+
+	vma->vm_ops = &xilinx_ai_engine_vm_ops;
+	/*
+	 * Make the dynamic memory mapping as write-combined. Only first one
+	 * will be the mmio region, which will be mapped as noncached.
+	 */
+	if (mi < 1)
+		vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	else
+		vma->vm_page_prot = pgprot_writecombine(vma->vm_page_prot);
+
+	/*
+	 * We cannot use the vm_iomap_memory() helper here,
+	 * because vma->vm_pgoff is the map index we looked
+	 * up above in uio_find_mem_index(), rather than an
+	 * actual page offset into the mmap.
+	 *
+	 * So we just do the physical mmap without a page
+	 * offset.
+	 */
+	return remap_pfn_range(vma,
+			       vma->vm_start,
+			       mem->addr >> PAGE_SHIFT,
+			       vma->vm_end - vma->vm_start,
+			       vma->vm_page_prot);
+}
+
+static int xilinx_ai_engine_probe(struct platform_device *pdev)
+{
+	struct platform_device *uio;
+	struct uio_dmem_genirq_pdata *pdata;
+	unsigned int i;
+	static const char * const interrupt_names[] = { "interrupt0",
+							"interrupt1",
+							"interrupt2",
+							"interrupt3" };
+	int ret;
+
+	uio = platform_device_alloc(DRIVER_NAME, PLATFORM_DEVID_NONE);
+	if (!uio)
+		return -ENOMEM;
+	uio->driver_override = "uio_dmem_genirq";
+	uio->dev.parent = &pdev->dev;
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata) {
+		ret = -ENOMEM;
+		goto err_out;
+	}
+
+	pdata->num_dynamic_regions = xilinx_ai_engine_mem_cnt;
+	pdata->dynamic_region_sizes = &xilinx_ai_engine_mem_size;
+	pdata->uioinfo.name = DRIVER_NAME;
+	pdata->uioinfo.version = "devicetree";
+	pdata->uioinfo.mmap = xilinx_ai_engine_mmap;
+	/* Set the offset value as it's map index for each memory */
+	for (i = 0; i < MAX_UIO_MAPS; i++)
+		pdata->uioinfo.mem[i].offs = i << PAGE_SHIFT;
+
+	/* TODO: Only one interrupt is supported out of 4 */
+	for (i  = 0; i < XILINX_AI_ENGINE_MAX_IRQ; i++) {
+		ret = platform_get_irq_byname(pdev, interrupt_names[i]);
+		if (ret >= 0) {
+			dev_info(&pdev->dev, "%s is used", interrupt_names[i]);
+			break;
+		}
+	}
+
+	/* Interrupt is optional */
+	if (ret < 0) {
+		ret = xilinx_ai_engine_simulate_irq(pdev);
+		if (ret < 0)
+			ret = UIO_IRQ_CUSTOM;
+	}
+	pdata->uioinfo.irq = ret;
+
+	ret = platform_device_add_data(uio, pdata, sizeof(*pdata));
+	if (ret)
+		goto err_out;
+
+	/* Mirror the parent device resource to uio device */
+	ret = platform_device_add_resources(uio, pdev->resource,
+					    pdev->num_resources);
+	if (ret)
+		goto err_out;
+
+	/* Configure the dma for uio device using the parent of_node */
+	uio->dev.bus = &platform_bus_type;
+	ret = of_dma_configure(&uio->dev, of_node_get(pdev->dev.of_node), true);
+	of_node_put(pdev->dev.of_node);
+	if (ret)
+		goto err_out;
+
+	ret = platform_device_add(uio);
+	if (ret)
+		goto err_out;
+	platform_set_drvdata(uio, pdata);
+	platform_set_drvdata(pdev, uio);
+
+	dev_info(&pdev->dev, "Xilinx AI Engine UIO driver probed");
+	return 0;
+
+err_out:
+	platform_device_put(uio);
+	dev_err(&pdev->dev,
+		"failed to probe Xilinx AI Engine UIO driver");
+	return ret;
+}
+
+static int xilinx_ai_engine_remove(struct platform_device *pdev)
+{
+	struct platform_device *uio = platform_get_drvdata(pdev);
+
+	platform_device_unregister(uio);
+	of_node_put(pdev->dev.of_node);
+
+	return 0;
+}
+
+static const struct of_device_id xilinx_ai_engine_of_match[] = {
+	{ .compatible = "xlnx,ai_engine", },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xilinx_ai_engine_of_match);
+
+static struct platform_driver xilinx_ai_engine_driver = {
+	.probe			= xilinx_ai_engine_probe,
+	.remove			= xilinx_ai_engine_remove,
+	.driver			= {
+		.name		= DRIVER_NAME,
+		.of_match_table	= xilinx_ai_engine_of_match,
+	},
+};
+
+module_platform_driver(xilinx_ai_engine_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/uio/uio_xilinx_apm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/uio/uio_xilinx_apm.c
@@ -0,0 +1,358 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx AXI Performance Monitor
+ *
+ * Copyright (C) 2013 - 2019 Xilinx, Inc. All rights reserved.
+ *
+ * Description:
+ * This driver is developed for AXI Performance Monitor IP,
+ * designed to monitor AXI4 traffic for performance analysis
+ * of AXI bus in the system. Driver maps HW registers and parameters
+ * to userspace. Userspace need not clear the interrupt of IP since
+ * driver clears the interrupt.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+#include <linux/uio_driver.h>
+
+#define XAPM_IS_OFFSET		0x0038  /* Interrupt Status Register */
+#define DRV_NAME		"xilinxapm_uio"
+#define DRV_VERSION		"1.0"
+#define UIO_DUMMY_MEMSIZE	4096
+#define XAPM_MODE_ADVANCED	1
+#define XAPM_MODE_PROFILE	2
+#define XAPM_MODE_TRACE		3
+
+/**
+ * struct xapm_param - HW parameters structure
+ * @mode: Mode in which APM is working
+ * @maxslots: Maximum number of Slots in APM
+ * @eventcnt: Event counting enabled in APM
+ * @eventlog: Event logging enabled in APM
+ * @sampledcnt: Sampled metric counters enabled in APM
+ * @numcounters: Number of counters in APM
+ * @metricwidth: Metric Counter width (32/64)
+ * @sampledwidth: Sampled metric counter width
+ * @globalcntwidth: Global Clock counter width
+ * @scalefactor: Scaling factor
+ * @isr: Interrupts info shared to userspace
+ * @is_32bit_filter: Flags for 32bit filter
+ * @clk: Clock handle
+ */
+struct xapm_param {
+	u32 mode;
+	u32 maxslots;
+	u32 eventcnt;
+	u32 eventlog;
+	u32 sampledcnt;
+	u32 numcounters;
+	u32 metricwidth;
+	u32 sampledwidth;
+	u32 globalcntwidth;
+	u32 scalefactor;
+	u32 isr;
+	bool is_32bit_filter;
+	struct clk *clk;
+};
+
+/**
+ * struct xapm_dev - Global driver structure
+ * @info: uio_info structure
+ * @param: xapm_param structure
+ * @regs: IOmapped base address
+ */
+struct xapm_dev {
+	struct uio_info info;
+	struct xapm_param param;
+	void __iomem *regs;
+};
+
+/**
+ * xapm_handler - Interrupt handler for APM
+ * @irq: IRQ number
+ * @info: Pointer to uio_info structure
+ *
+ * Return: Always returns IRQ_HANDLED
+ */
+static irqreturn_t xapm_handler(int irq, struct uio_info *info)
+{
+	struct xapm_dev *xapm = (struct xapm_dev *)info->priv;
+	void *ptr;
+
+	ptr = (unsigned long *)xapm->info.mem[1].addr;
+	/* Clear the interrupt and copy the ISR value to userspace */
+	xapm->param.isr = readl(xapm->regs + XAPM_IS_OFFSET);
+	writel(xapm->param.isr, xapm->regs + XAPM_IS_OFFSET);
+	memcpy(ptr, &xapm->param, sizeof(struct xapm_param));
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xapm_getprop - Retrieves dts properties to param structure
+ * @pdev: Pointer to platform device
+ * @param: Pointer to param structure
+ *
+ * Returns: '0' on success and failure value on error
+ */
+static int xapm_getprop(struct platform_device *pdev, struct xapm_param *param)
+{
+	u32 mode = 0;
+	int ret;
+	struct device_node *node;
+
+	node = pdev->dev.of_node;
+
+	/* Retrieve required dts properties and fill param structure */
+	ret = of_property_read_u32(node, "xlnx,enable-profile", &mode);
+	if (ret < 0)
+		dev_info(&pdev->dev, "no property xlnx,enable-profile\n");
+	else if (mode)
+		param->mode = XAPM_MODE_PROFILE;
+
+	ret = of_property_read_u32(node, "xlnx,enable-trace", &mode);
+	if (ret < 0)
+		dev_info(&pdev->dev, "no property xlnx,enable-trace\n");
+	else if (mode)
+		param->mode = XAPM_MODE_TRACE;
+
+	ret = of_property_read_u32(node, "xlnx,num-monitor-slots",
+				   &param->maxslots);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,num-monitor-slots");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,enable-event-count",
+				   &param->eventcnt);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,enable-event-count");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,enable-event-log",
+				   &param->eventlog);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,enable-event-log");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,have-sampled-metric-cnt",
+				   &param->sampledcnt);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,have-sampled-metric-cnt");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,num-of-counters",
+				   &param->numcounters);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,num-of-counters");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,metric-count-width",
+				   &param->metricwidth);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,metric-count-width");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,metrics-sample-count-width",
+				   &param->sampledwidth);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property metrics-sample-count-width");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,global-count-width",
+				   &param->globalcntwidth);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,global-count-width");
+		return ret;
+	}
+
+	ret = of_property_read_u32(node, "xlnx,metric-count-scale",
+				   &param->scalefactor);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "no property xlnx,metric-count-scale");
+		return ret;
+	}
+
+	param->is_32bit_filter = of_property_read_bool(node,
+						"xlnx,id-filter-32bit");
+
+	return 0;
+}
+
+/**
+ * xapm_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * Returns: '0' on success and failure value on error
+ */
+
+static int xapm_probe(struct platform_device *pdev)
+{
+	struct xapm_dev *xapm;
+	struct resource *res;
+	int irq;
+	int ret;
+	void *ptr;
+
+	xapm = devm_kzalloc(&pdev->dev, (sizeof(struct xapm_dev)), GFP_KERNEL);
+	if (!xapm)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xapm->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(xapm->regs)) {
+		dev_err(&pdev->dev, "unable to iomap registers\n");
+		return PTR_ERR(xapm->regs);
+	}
+
+	xapm->param.clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(xapm->param.clk)) {
+		if (PTR_ERR(xapm->param.clk) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "axi clock error\n");
+		return PTR_ERR(xapm->param.clk);
+	}
+
+	ret = clk_prepare_enable(xapm->param.clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return ret;
+	}
+	pm_runtime_get_noresume(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	/* Initialize mode as Advanced so that if no mode in dts, default
+	 * is Advanced
+	 */
+	xapm->param.mode = XAPM_MODE_ADVANCED;
+	ret = xapm_getprop(pdev, &xapm->param);
+	if (ret < 0)
+		goto err_clk_dis;
+
+	xapm->info.mem[0].name = "xilinx_apm";
+	xapm->info.mem[0].addr = res->start;
+	xapm->info.mem[0].size = resource_size(res);
+	xapm->info.mem[0].memtype = UIO_MEM_PHYS;
+
+	xapm->info.mem[1].addr = (unsigned long)kzalloc(UIO_DUMMY_MEMSIZE,
+							GFP_KERNEL);
+	ptr = (unsigned long *)xapm->info.mem[1].addr;
+	xapm->info.mem[1].size = UIO_DUMMY_MEMSIZE;
+	xapm->info.mem[1].memtype = UIO_MEM_LOGICAL;
+
+	xapm->info.name = "axi-pmon";
+	xapm->info.version = DRV_VERSION;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "unable to get irq\n");
+		ret = irq;
+		goto err_clk_dis;
+	}
+
+	xapm->info.irq = irq;
+	xapm->info.handler = xapm_handler;
+	xapm->info.priv = xapm;
+	xapm->info.irq_flags = IRQF_SHARED;
+
+	memcpy(ptr, &xapm->param, sizeof(struct xapm_param));
+
+	ret = uio_register_device(&pdev->dev, &xapm->info);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "unable to register to UIO\n");
+		goto err_clk_dis;
+	}
+
+	platform_set_drvdata(pdev, xapm);
+
+	dev_info(&pdev->dev, "Probed Xilinx APM\n");
+
+	return 0;
+
+err_clk_dis:
+	clk_disable_unprepare(xapm->param.clk);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	return ret;
+}
+
+/**
+ * xapm_remove - Driver remove function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * Return: Always returns '0'
+ */
+static int xapm_remove(struct platform_device *pdev)
+{
+	struct xapm_dev *xapm = platform_get_drvdata(pdev);
+
+	uio_unregister_device(&xapm->info);
+	clk_disable_unprepare(xapm->param.clk);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+
+	return 0;
+}
+
+static int __maybe_unused xapm_runtime_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct xapm_dev *xapm = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(xapm->param.clk);
+	return 0;
+};
+
+static int __maybe_unused xapm_runtime_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct xapm_dev *xapm = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = clk_prepare_enable(xapm->param.clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return ret;
+	}
+	return 0;
+};
+
+static const struct dev_pm_ops xapm_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xapm_runtime_suspend, xapm_runtime_resume)
+	SET_RUNTIME_PM_OPS(xapm_runtime_suspend,
+			   xapm_runtime_resume, NULL)
+};
+
+static const struct of_device_id xapm_of_match[] = {
+	{ .compatible = "xlnx,axi-perf-monitor", },
+	{ /* end of table*/ }
+};
+
+MODULE_DEVICE_TABLE(of, xapm_of_match);
+
+static struct platform_driver xapm_driver = {
+	.driver = {
+		.name = "xilinx-axipmon",
+		.of_match_table = xapm_of_match,
+		.pm = &xapm_dev_pm_ops,
+	},
+	.probe = xapm_probe,
+	.remove = xapm_remove,
+};
+
+module_platform_driver(xapm_driver);
+
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_DESCRIPTION("Xilinx AXI Performance Monitor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/atm/cxacru.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/atm/cxacru.c
@@ -1131,6 +1131,10 @@
 	struct cxacru_data *instance;
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
 	struct usb_host_endpoint *cmd_ep = usb_dev->ep_in[CXACRU_EP_CMD];
+	static const u8 ep_addrs[] = {
+		CXACRU_EP_CMD + USB_DIR_IN,
+		CXACRU_EP_CMD + USB_DIR_OUT,
+		0};
 	int ret;
 
 	/* instance init */
@@ -1176,6 +1180,17 @@
 		ret = -ENODEV;
 		goto fail;
 	}
+
+	if (usb_endpoint_xfer_int(&cmd_ep->desc))
+		ret = usb_check_int_endpoints(intf, ep_addrs);
+	else
+		ret = usb_check_bulk_endpoints(intf, ep_addrs);
+
+	if (!ret) {
+		usb_err(usbatm_instance, "cxacru_bind: interface has incorrect endpoints\n");
+		ret = -ENODEV;
+		goto fail;
+	}
 
 	if ((cmd_ep->desc.bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
 			== USB_ENDPOINT_XFER_INT) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdns3-gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdns3-gadget.c
@@ -220,7 +220,7 @@
 
 	if (!priv_ep->trb_pool) {
 		priv_ep->trb_pool = dma_pool_alloc(priv_dev->eps_dma_pool,
-						   GFP_DMA32 | GFP_ATOMIC,
+						   GFP_ATOMIC,
 						   &priv_ep->trb_pool_dma);
 
 		if (!priv_ep->trb_pool)
@@ -337,19 +337,6 @@
 	cdns3_ep_inc_trb(&priv_ep->dequeue, &priv_ep->ccs, priv_ep->num_trbs);
 }
 
-static void cdns3_move_deq_to_next_trb(struct cdns3_request *priv_req)
-{
-	struct cdns3_endpoint *priv_ep = priv_req->priv_ep;
-	int current_trb = priv_req->start_trb;
-
-	while (current_trb != priv_req->end_trb) {
-		cdns3_ep_inc_deq(priv_ep);
-		current_trb = priv_ep->dequeue;
-	}
-
-	cdns3_ep_inc_deq(priv_ep);
-}
-
 /**
  * cdns3_allow_enable_l1 - enable/disable permits to transition to L1.
  * @priv_dev: Extended gadget object
@@ -638,9 +625,9 @@
 		trace_cdns3_wa2(priv_ep, "removes eldest request");
 
 		kfree(priv_req->request.buf);
+		list_del_init(&priv_req->list);
 		cdns3_gadget_ep_free_request(&priv_ep->endpoint,
 					     &priv_req->request);
-		list_del_init(&priv_req->list);
 		--priv_ep->wa2_counter;
 
 		if (!chain)
@@ -839,7 +826,11 @@
 			return;
 	}
 
-	if (request->complete) {
+	/*
+	 * zlp request is appended by driver, needn't call usb_gadget_giveback_request() to notify
+	 * gadget composite driver.
+	 */
+	if (request->complete && request->buf != priv_dev->zlp_buf) {
 		spin_unlock(&priv_dev->lock);
 		usb_gadget_giveback_request(&priv_ep->endpoint,
 					    request);
@@ -1130,6 +1121,8 @@
 	dma_addr_t trb_dma;
 	u32 togle_pcs = 1;
 	int sg_iter = 0;
+	int num_trb_req;
+	int trb_burst;
 	int num_trb;
 	int address;
 	u32 control;
@@ -1138,15 +1131,13 @@
 	struct scatterlist *s = NULL;
 	bool sg_supported = !!(request->num_mapped_sgs);
 
+	num_trb_req = sg_supported ? request->num_mapped_sgs : 1;
+
+	/* ISO transfer require each SOF have a TD, each TD include some TRBs */
 	if (priv_ep->type == USB_ENDPOINT_XFER_ISOC)
-		num_trb = priv_ep->interval;
+		num_trb = priv_ep->interval * num_trb_req;
 	else
-		num_trb = sg_supported ? request->num_mapped_sgs : 1;
-
-	if (num_trb > priv_ep->free_trbs) {
-		priv_ep->flags |= EP_RING_FULL;
-		return -ENOBUFS;
-	}
+		num_trb = num_trb_req;
 
 	priv_req = to_cdns3_request(request);
 	address = priv_ep->endpoint.desc->bEndpointAddress;
@@ -1195,14 +1186,31 @@
 
 		link_trb->control = cpu_to_le32(((priv_ep->pcs) ? TRB_CYCLE : 0) |
 				    TRB_TYPE(TRB_LINK) | TRB_TOGGLE | ch_bit);
+
+		if (priv_ep->type == USB_ENDPOINT_XFER_ISOC) {
+			/*
+			 * ISO require LINK TRB must be first one of TD.
+			 * Fill LINK TRBs for left trb space to simply software process logic.
+			 */
+			while (priv_ep->enqueue) {
+				*trb = *link_trb;
+				trace_cdns3_prepare_trb(priv_ep, trb);
+
+				cdns3_ep_inc_enq(priv_ep);
+				trb = priv_ep->trb_pool + priv_ep->enqueue;
+				priv_req->trb = trb;
+			}
+		}
+	}
+
+	if (num_trb > priv_ep->free_trbs) {
+		priv_ep->flags |= EP_RING_FULL;
+		return -ENOBUFS;
 	}
 
 	if (priv_dev->dev_ver <= DEV_VER_V2)
 		togle_pcs = cdns3_wa1_update_guard(priv_ep, trb);
 
-	if (sg_supported)
-		s = request->sg;
-
 	/* set incorrect Cycle Bit for first trb*/
 	control = priv_ep->pcs ? 0 : TRB_CYCLE;
 	trb->length = 0;
@@ -1220,6 +1228,9 @@
 	do {
 		u32 length;
 
+		if (!(sg_iter % num_trb_req) && sg_supported)
+			s = request->sg;
+
 		/* fill TRB */
 		control |= TRB_TYPE(TRB_NORMAL);
 		if (sg_supported) {
@@ -1234,7 +1245,36 @@
 			total_tdl += DIV_ROUND_UP(length,
 					       priv_ep->endpoint.maxpacket);
 
-		trb->length |= cpu_to_le32(TRB_BURST_LEN(priv_ep->trb_burst_size) |
+		trb_burst = priv_ep->trb_burst_size;
+
+		/*
+		 * Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but still
+		 * met problem when do ISO transfer if sg enabled.
+		 *
+		 * Data pattern likes below when sg enabled, package size is 1k and mult is 2
+		 *       [UVC Header(8B) ] [data(3k - 8)] ...
+		 *
+		 * The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error happen
+		 * as below pattern:
+		 *	0xd000: wrong
+		 *	0xe000: wrong
+		 *	0xf000: correct
+		 *	0x10000: wrong
+		 *	0x11000: wrong
+		 *	0x12000: correct
+		 *	...
+		 *
+		 * But it is still unclear about why error have not happen below 0xd000, it should
+		 * cross 4k bounder. But anyway, the below code can fix this problem.
+		 *
+		 * To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according to 16.
+		 */
+		if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && priv_dev->dev_ver <= DEV_VER_V2)
+			if (ALIGN_DOWN(trb->buffer, SZ_4K) !=
+			    ALIGN_DOWN(trb->buffer + length, SZ_4K))
+				trb_burst = 16;
+
+		trb->length |= cpu_to_le32(TRB_BURST_LEN(trb_burst) |
 					TRB_LEN(length));
 		pcs = priv_ep->pcs ? TRB_CYCLE : 0;
 
@@ -1261,7 +1301,7 @@
 		if (sg_supported) {
 			trb->control |= cpu_to_le32(TRB_ISP);
 			/* Don't set chain bit for last TRB */
-			if (sg_iter < num_trb - 1)
+			if ((sg_iter % num_trb_req) < num_trb_req - 1)
 				trb->control |= cpu_to_le32(TRB_CHAIN);
 
 			s = sg_next(s);
@@ -1517,10 +1557,17 @@
 
 		trb = priv_ep->trb_pool + priv_ep->dequeue;
 
-		/* Request was dequeued and TRB was changed to TRB_LINK. */
-		if (TRB_FIELD_TO_TYPE(le32_to_cpu(trb->control)) == TRB_LINK) {
+		/* The TRB was changed as link TRB, and the request was handled at ep_dequeue */
+		while (TRB_FIELD_TO_TYPE(le32_to_cpu(trb->control)) == TRB_LINK) {
+
+			/* ISO ep_traddr may stop at LINK TRB */
+			if (priv_ep->dequeue == cdns3_get_dma_pos(priv_dev, priv_ep) &&
+			    priv_ep->type == USB_ENDPOINT_XFER_ISOC)
+				break;
+
 			trace_cdns3_complete_trb(priv_ep, trb);
-			cdns3_move_deq_to_next_trb(priv_req);
+			cdns3_ep_inc_deq(priv_ep);
+			trb = priv_ep->trb_pool + priv_ep->dequeue;
 		}
 
 		if (!request->stream_id) {
@@ -1542,13 +1589,18 @@
 						TRB_LEN(le32_to_cpu(trb->length));
 
 				if (priv_req->num_of_trb > 1 &&
-					le32_to_cpu(trb->control) & TRB_SMM)
+					le32_to_cpu(trb->control) & TRB_SMM &&
+					le32_to_cpu(trb->control) & TRB_CHAIN)
 					transfer_end = true;
 
 				cdns3_ep_inc_deq(priv_ep);
 			}
 
 			if (request_handled) {
+				/* TRBs are duplicated by priv_ep->interval time for ISO IN */
+				if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && priv_ep->dir)
+					request->actual /= priv_ep->interval;
+
 				cdns3_gadget_giveback(priv_ep, priv_req, 0);
 				request_handled = false;
 				transfer_end = false;
@@ -1702,6 +1754,7 @@
 				ep_cfg &= ~EP_CFG_ENABLE;
 				writel(ep_cfg, &priv_dev->regs->ep_cfg);
 				priv_ep->flags &= ~EP_QUIRK_ISO_OUT_EN;
+				priv_ep->flags |= EP_UPDATE_EP_TRBADDR;
 			}
 			cdns3_transfer_completed(priv_dev, priv_ep);
 		} else if (!(priv_ep->flags & EP_STALLED) &&
@@ -2043,14 +2096,13 @@
 	bool is_iso_ep = (priv_ep->type == USB_ENDPOINT_XFER_ISOC);
 	struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
 	u32 bEndpointAddress = priv_ep->num | priv_ep->dir;
-	u32 max_packet_size = 0;
-	u8 maxburst = 0;
+	u32 max_packet_size = priv_ep->wMaxPacketSize;
+	u8 maxburst = priv_ep->bMaxBurst;
 	u32 ep_cfg = 0;
 	u8 buffering;
-	u8 mult = 0;
 	int ret;
 
-	buffering = CDNS3_EP_BUF_SIZE - 1;
+	buffering = priv_dev->ep_buf_size - 1;
 
 	cdns3_configure_dmult(priv_dev, priv_ep);
 
@@ -2069,8 +2121,7 @@
 		break;
 	default:
 		ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_ISOC);
-		mult = CDNS3_EP_ISO_HS_MULT - 1;
-		buffering = mult + 1;
+		buffering = (priv_ep->bMaxBurst + 1) * (priv_ep->mult + 1) - 1;
 	}
 
 	switch (priv_dev->gadget.speed) {
@@ -2081,18 +2132,9 @@
 		max_packet_size = is_iso_ep ? 1024 : 512;
 		break;
 	case USB_SPEED_SUPER:
-		/* It's limitation that driver assumes in driver. */
-		mult = 0;
-		max_packet_size = 1024;
-		if (priv_ep->type == USB_ENDPOINT_XFER_ISOC) {
-			maxburst = CDNS3_EP_ISO_SS_BURST - 1;
-			buffering = (mult + 1) *
-				    (maxburst + 1);
-
-			if (priv_ep->interval > 1)
-				buffering++;
-		} else {
-			maxburst = CDNS3_EP_BUF_SIZE - 1;
+		if (priv_ep->type != USB_ENDPOINT_XFER_ISOC) {
+			max_packet_size = 1024;
+			maxburst = priv_dev->ep_buf_size - 1;
 		}
 		break;
 	default:
@@ -2107,6 +2149,22 @@
 	else
 		priv_ep->trb_burst_size = 16;
 
+	/*
+	 * In versions preceding DEV_VER_V2, for example, iMX8QM, there exit the bugs
+	 * in the DMA. These bugs occur when the trb_burst_size exceeds 16 and the
+	 * address is not aligned to 128 Bytes (which is a product of the 64-bit AXI
+	 * and AXI maximum burst length of 16 or 0xF+1, dma_axi_ctrl0[3:0]). This
+	 * results in data corruption when it crosses the 4K border. The corruption
+	 * specifically occurs from the position (4K - (address & 0x7F)) to 4K.
+	 *
+	 * So force trb_burst_size to 16 at such platform.
+	 */
+	if (priv_dev->dev_ver < DEV_VER_V2)
+		priv_ep->trb_burst_size = 16;
+
+	buffering = min_t(u8, buffering, EP_CFG_BUFFERING_MAX);
+	maxburst = min_t(u8, maxburst, EP_CFG_MAXBURST_MAX);
+
 	/* onchip buffer is only allocated before configuration */
 	if (!priv_dev->hw_configured_flag) {
 		ret = cdns3_ep_onchip_buffer_reserve(priv_dev, buffering + 1,
@@ -2137,7 +2195,7 @@
 	}
 
 	ep_cfg |= EP_CFG_MAXPKTSIZE(max_packet_size) |
-		  EP_CFG_MULT(mult) |
+		  EP_CFG_MULT(priv_ep->mult) |			/* must match EP setting */
 		  EP_CFG_BUFFERING(buffering) |
 		  EP_CFG_MAXBURST(maxburst);
 
@@ -2227,6 +2285,13 @@
 	priv_ep->type = usb_endpoint_type(desc);
 	priv_ep->flags |= EP_CLAIMED;
 	priv_ep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0;
+	priv_ep->wMaxPacketSize =  usb_endpoint_maxp(desc);
+	priv_ep->mult = USB_EP_MAXP_MULT(priv_ep->wMaxPacketSize);
+	priv_ep->wMaxPacketSize &= USB_ENDPOINT_MAXP_MASK;
+	if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && comp_desc) {
+		priv_ep->mult =  USB_SS_MULT(comp_desc->bmAttributes) - 1;
+		priv_ep->bMaxBurst = comp_desc->bMaxBurst;
+	}
 
 	spin_unlock_irqrestore(&priv_dev->lock, flags);
 	return &priv_ep->endpoint;
@@ -2292,11 +2357,16 @@
 	int ret = 0;
 	int val;
 
+	if (!ep) {
+		pr_debug("usbss: ep not configured?\n");
+		return -EINVAL;
+	}
+
 	priv_ep = ep_to_cdns3_ep(ep);
 	priv_dev = priv_ep->cdns3_dev;
 	comp_desc = priv_ep->endpoint.comp_desc;
 
-	if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
+	if (!desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
 		dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
 		return -EINVAL;
 	}
@@ -2471,11 +2541,11 @@
 
 	while (!list_empty(&priv_ep->wa2_descmiss_req_list)) {
 		priv_req = cdns3_next_priv_request(&priv_ep->wa2_descmiss_req_list);
+		list_del_init(&priv_req->list);
 
 		kfree(priv_req->request.buf);
 		cdns3_gadget_ep_free_request(&priv_ep->endpoint,
 					     &priv_req->request);
-		list_del_init(&priv_req->list);
 		--priv_ep->wa2_counter;
 	}
 
@@ -2608,17 +2678,20 @@
 			    struct usb_request *request)
 {
 	struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
-	struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
+	struct cdns3_device *priv_dev;
 	struct usb_request *req, *req_temp;
 	struct cdns3_request *priv_req;
 	struct cdns3_trb *link_trb;
 	u8 req_on_hw_ring = 0;
 	unsigned long flags;
 	int ret = 0;
+	int val;
 
 	if (!ep || !request || !ep->desc)
 		return -EINVAL;
 
+	priv_dev = priv_ep->cdns3_dev;
+
 	spin_lock_irqsave(&priv_dev->lock, flags);
 
 	priv_req = to_cdns3_request(request);
@@ -2648,6 +2721,13 @@
 
 	/* Update ring only if removed request is on pending_req_list list */
 	if (req_on_hw_ring && link_trb) {
+		/* Stop DMA */
+		writel(EP_CMD_DFLUSH, &priv_dev->regs->ep_cmd);
+
+		/* wait for DFLUSH cleared */
+		readl_poll_timeout_atomic(&priv_dev->regs->ep_cmd, val,
+					  !(val & EP_CMD_DFLUSH), 1, 1000);
+
 		link_trb->buffer = cpu_to_le32(TRB_BUFFER(priv_ep->trb_pool_dma +
 			((priv_req->end_trb + 1) * TRB_SIZE)));
 		link_trb->control = cpu_to_le32((le32_to_cpu(link_trb->control) & TRB_CYCLE) |
@@ -2659,6 +2739,10 @@
 
 	cdns3_gadget_giveback(priv_ep, priv_req, -ECONNRESET);
 
+	req = cdns3_next_request(&priv_ep->pending_req_list);
+	if (req)
+		cdns3_rearm_transfer(priv_ep, 1);
+
 not_found:
 	spin_unlock_irqrestore(&priv_dev->lock, flags);
 	return ret;
@@ -2696,6 +2780,7 @@
 	struct usb_request *request;
 	struct cdns3_request *priv_req;
 	struct cdns3_trb *trb = NULL;
+	struct cdns3_trb trb_tmp;
 	int ret;
 	int val;
 
@@ -2705,8 +2790,10 @@
 	if (request) {
 		priv_req = to_cdns3_request(request);
 		trb = priv_req->trb;
-		if (trb)
+		if (trb) {
+			trb_tmp = *trb;
 			trb->control = trb->control ^ cpu_to_le32(TRB_CYCLE);
+		}
 	}
 
 	writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
@@ -2721,7 +2808,7 @@
 
 	if (request) {
 		if (trb)
-			trb->control = trb->control ^ cpu_to_le32(TRB_CYCLE);
+			*trb = trb_tmp;
 
 		cdns3_rearm_transfer(priv_ep, 1);
 	}
@@ -2970,6 +3057,60 @@
 	return 0;
 }
 
+/**
+ * cdns3_gadget_check_config - ensure cdns3 can support the USB configuration
+ * @gadget: pointer to the USB gadget
+ *
+ * Used to record the maximum number of endpoints being used in a USB composite
+ * device. (across all configurations)  This is to be used in the calculation
+ * of the TXFIFO sizes when resizing internal memory for individual endpoints.
+ * It will help ensured that the resizing logic reserves enough space for at
+ * least one max packet.
+ */
+static int cdns3_gadget_check_config(struct usb_gadget *gadget)
+{
+	struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
+	struct cdns3_endpoint *priv_ep;
+	struct usb_ep *ep;
+	int n_in = 0;
+	int iso = 0;
+	int out = 1;
+	int total;
+	int n;
+
+	list_for_each_entry(ep, &gadget->ep_list, ep_list) {
+		priv_ep = ep_to_cdns3_ep(ep);
+		if (!(priv_ep->flags & EP_CLAIMED))
+			continue;
+
+		n = (priv_ep->mult + 1) * (priv_ep->bMaxBurst + 1);
+		if (ep->address & USB_DIR_IN) {
+			/*
+			 * ISO transfer: DMA start move data when get ISO, only transfer
+			 * data as min(TD size, iso). No benefit for allocate bigger
+			 * internal memory than 'iso'.
+			 */
+			if (priv_ep->type == USB_ENDPOINT_XFER_ISOC)
+				iso += n;
+			else
+				n_in++;
+		} else {
+			if (priv_ep->type == USB_ENDPOINT_XFER_ISOC)
+				out = max_t(int, out, n);
+		}
+	}
+
+	/* 2KB are reserved for EP0, 1KB for out*/
+	total = 2 + n_in + out + iso;
+
+	if (total > priv_dev->onchip_buffers)
+		return -ENOMEM;
+
+	priv_dev->ep_buf_size = (priv_dev->onchip_buffers - 2 - iso) / (n_in + out);
+
+	return 0;
+}
+
 static const struct usb_gadget_ops cdns3_gadget_ops = {
 	.get_frame = cdns3_gadget_get_frame,
 	.wakeup = cdns3_gadget_wakeup,
@@ -2978,6 +3119,7 @@
 	.udc_start = cdns3_gadget_udc_start,
 	.udc_stop = cdns3_gadget_udc_stop,
 	.match_ep = cdns3_gadget_match_ep,
+	.check_config = cdns3_gadget_check_config,
 };
 
 static void cdns3_free_all_eps(struct cdns3_device *priv_dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdns3-gadget.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdns3-gadget.h
@@ -562,15 +562,18 @@
 /* Max burst size (used only in SS mode). */
 #define EP_CFG_MAXBURST_MASK	GENMASK(11, 8)
 #define EP_CFG_MAXBURST(p)	(((p) << 8) & EP_CFG_MAXBURST_MASK)
+#define EP_CFG_MAXBURST_MAX	15
 /* ISO max burst. */
 #define EP_CFG_MULT_MASK	GENMASK(15, 14)
 #define EP_CFG_MULT(p)		(((p) << 14) & EP_CFG_MULT_MASK)
+#define EP_CFG_MULT_MAX		2
 /* ISO max burst. */
 #define EP_CFG_MAXPKTSIZE_MASK	GENMASK(26, 16)
 #define EP_CFG_MAXPKTSIZE(p)	(((p) << 16) & EP_CFG_MAXPKTSIZE_MASK)
 /* Max number of buffered packets. */
 #define EP_CFG_BUFFERING_MASK	GENMASK(31, 27)
 #define EP_CFG_BUFFERING(p)	(((p) << 27) & EP_CFG_BUFFERING_MASK)
+#define EP_CFG_BUFFERING_MAX	15
 
 /* EP_CMD - bitmasks */
 /* Endpoint reset. */
@@ -1094,9 +1097,6 @@
 #define CDNS3_ENDPOINTS_MAX_COUNT	32
 #define CDNS3_EP_ZLP_BUF_SIZE		1024
 
-#define CDNS3_EP_BUF_SIZE		4	/* KB */
-#define CDNS3_EP_ISO_HS_MULT		3
-#define CDNS3_EP_ISO_SS_BURST		3
 #define CDNS3_MAX_NUM_DESCMISS_BUF	32
 #define CDNS3_DESCMIS_BUF_SIZE		2048	/* Bytes */
 #define CDNS3_WA2_NUM_BUFFERS		128
@@ -1168,6 +1168,9 @@
 	u8			dir;
 	u8			num;
 	u8			type;
+	u8			mult;
+	u8			bMaxBurst;
+	u16			wMaxPacketSize;
 	int			interval;
 
 	int			free_trbs;
@@ -1333,6 +1336,9 @@
 	/*in KB */
 	u16				onchip_buffers;
 	u16				onchip_used_size;
+
+	u16				ep_buf_size;
+	u16				ep_iso_burst;
 };
 
 void cdns3_set_register_bit(void __iomem *ptr, u32 mask);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdns3-pci-wrap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdns3-pci-wrap.c
@@ -60,6 +60,11 @@
 			return NULL;
 	}
 
+	if (func->devfn != PCI_DEV_FN_HOST_DEVICE &&
+	    func->devfn != PCI_DEV_FN_OTG) {
+		return NULL;
+	}
+
 	return func;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdns3-plat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdns3-plat.c
@@ -256,9 +256,10 @@
 	cdns3_set_platform_suspend(cdns->dev, false, false);
 
 	spin_lock_irqsave(&cdns->lock, flags);
-	cdns_resume(cdns, !PMSG_IS_AUTO(msg));
+	cdns_resume(cdns);
 	cdns->in_lpm = false;
 	spin_unlock_irqrestore(&cdns->lock, flags);
+	cdns_set_active(cdns, !PMSG_IS_AUTO(msg));
 	if (cdns->wakeup_pending) {
 		cdns->wakeup_pending = false;
 		enable_irq(cdns->wakeup_irq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-debug.h
@@ -182,208 +182,211 @@
 	int ep_id = TRB_TO_EP_INDEX(field3) - 1;
 	int type = TRB_FIELD_TO_TYPE(field3);
 	unsigned int ep_num;
-	int ret = 0;
+	int ret;
 	u32 temp;
 
 	ep_num = DIV_ROUND_UP(ep_id, 2);
 
 	switch (type) {
 	case TRB_LINK:
-		ret += snprintf(str, size,
-				"LINK %08x%08x intr %ld type '%s' flags %c:%c:%c:%c",
-				field1, field0, GET_INTR_TARGET(field2),
-				cdnsp_trb_type_string(type),
-				field3 & TRB_IOC ? 'I' : 'i',
-				field3 & TRB_CHAIN ? 'C' : 'c',
-				field3 & TRB_TC ? 'T' : 't',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "LINK %08x%08x intr %ld type '%s' flags %c:%c:%c:%c",
+			       field1, field0, GET_INTR_TARGET(field2),
+			       cdnsp_trb_type_string(type),
+			       field3 & TRB_IOC ? 'I' : 'i',
+			       field3 & TRB_CHAIN ? 'C' : 'c',
+			       field3 & TRB_TC ? 'T' : 't',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_TRANSFER:
 	case TRB_COMPLETION:
 	case TRB_PORT_STATUS:
 	case TRB_HC_EVENT:
-		ret += snprintf(str, size,
-				"ep%d%s(%d) type '%s' TRB %08x%08x status '%s'"
-				" len %ld slot %ld flags %c:%c",
-				ep_num, ep_id % 2 ? "out" : "in",
-				TRB_TO_EP_INDEX(field3),
-				cdnsp_trb_type_string(type), field1, field0,
-				cdnsp_trb_comp_code_string(GET_COMP_CODE(field2)),
-				EVENT_TRB_LEN(field2), TRB_TO_SLOT_ID(field3),
-				field3 & EVENT_DATA ? 'E' : 'e',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "ep%d%s(%d) type '%s' TRB %08x%08x status '%s'"
+			       " len %ld slot %ld flags %c:%c",
+			       ep_num, ep_id % 2 ? "out" : "in",
+			       TRB_TO_EP_INDEX(field3),
+			       cdnsp_trb_type_string(type), field1, field0,
+			       cdnsp_trb_comp_code_string(GET_COMP_CODE(field2)),
+			       EVENT_TRB_LEN(field2), TRB_TO_SLOT_ID(field3),
+			       field3 & EVENT_DATA ? 'E' : 'e',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_MFINDEX_WRAP:
-		ret += snprintf(str, size, "%s: flags %c",
-				cdnsp_trb_type_string(type),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size, "%s: flags %c",
+			       cdnsp_trb_type_string(type),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_SETUP:
-		ret += snprintf(str, size,
-				"type '%s' bRequestType %02x bRequest %02x "
-				"wValue %02x%02x wIndex %02x%02x wLength %d "
-				"length %ld TD size %ld intr %ld Setup ID %ld "
-				"flags %c:%c:%c",
-				cdnsp_trb_type_string(type),
-				field0 & 0xff,
-				(field0 & 0xff00) >> 8,
-				(field0 & 0xff000000) >> 24,
-				(field0 & 0xff0000) >> 16,
-				(field1 & 0xff00) >> 8,
-				field1 & 0xff,
-				(field1 & 0xff000000) >> 16 |
-				(field1 & 0xff0000) >> 16,
-				TRB_LEN(field2), GET_TD_SIZE(field2),
-				GET_INTR_TARGET(field2),
-				TRB_SETUPID_TO_TYPE(field3),
-				field3 & TRB_IDT ? 'D' : 'd',
-				field3 & TRB_IOC ? 'I' : 'i',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "type '%s' bRequestType %02x bRequest %02x "
+			       "wValue %02x%02x wIndex %02x%02x wLength %d "
+			       "length %ld TD size %ld intr %ld Setup ID %ld "
+			       "flags %c:%c:%c",
+			       cdnsp_trb_type_string(type),
+			       field0 & 0xff,
+			       (field0 & 0xff00) >> 8,
+			       (field0 & 0xff000000) >> 24,
+			       (field0 & 0xff0000) >> 16,
+			       (field1 & 0xff00) >> 8,
+			       field1 & 0xff,
+			       (field1 & 0xff000000) >> 16 |
+			       (field1 & 0xff0000) >> 16,
+			       TRB_LEN(field2), GET_TD_SIZE(field2),
+			       GET_INTR_TARGET(field2),
+			       TRB_SETUPID_TO_TYPE(field3),
+			       field3 & TRB_IDT ? 'D' : 'd',
+			       field3 & TRB_IOC ? 'I' : 'i',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_DATA:
-		ret += snprintf(str, size,
-				"type '%s' Buffer %08x%08x length %ld TD size %ld "
-				"intr %ld flags %c:%c:%c:%c:%c:%c:%c",
-				cdnsp_trb_type_string(type),
-				field1, field0, TRB_LEN(field2),
-				GET_TD_SIZE(field2),
-				GET_INTR_TARGET(field2),
-				field3 & TRB_IDT ? 'D' : 'i',
-				field3 & TRB_IOC ? 'I' : 'i',
-				field3 & TRB_CHAIN ? 'C' : 'c',
-				field3 & TRB_NO_SNOOP ? 'S' : 's',
-				field3 & TRB_ISP ? 'I' : 'i',
-				field3 & TRB_ENT ? 'E' : 'e',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "type '%s' Buffer %08x%08x length %ld TD size %ld "
+			       "intr %ld flags %c:%c:%c:%c:%c:%c:%c",
+			       cdnsp_trb_type_string(type),
+			       field1, field0, TRB_LEN(field2),
+			       GET_TD_SIZE(field2),
+			       GET_INTR_TARGET(field2),
+			       field3 & TRB_IDT ? 'D' : 'i',
+			       field3 & TRB_IOC ? 'I' : 'i',
+			       field3 & TRB_CHAIN ? 'C' : 'c',
+			       field3 & TRB_NO_SNOOP ? 'S' : 's',
+			       field3 & TRB_ISP ? 'I' : 'i',
+			       field3 & TRB_ENT ? 'E' : 'e',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_STATUS:
-		ret += snprintf(str, size,
-				"Buffer %08x%08x length %ld TD size %ld intr"
-				"%ld type '%s' flags %c:%c:%c:%c",
-				field1, field0, TRB_LEN(field2),
-				GET_TD_SIZE(field2),
-				GET_INTR_TARGET(field2),
-				cdnsp_trb_type_string(type),
-				field3 & TRB_IOC ? 'I' : 'i',
-				field3 & TRB_CHAIN ? 'C' : 'c',
-				field3 & TRB_ENT ? 'E' : 'e',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "Buffer %08x%08x length %ld TD size %ld intr"
+			       "%ld type '%s' flags %c:%c:%c:%c",
+			       field1, field0, TRB_LEN(field2),
+			       GET_TD_SIZE(field2),
+			       GET_INTR_TARGET(field2),
+			       cdnsp_trb_type_string(type),
+			       field3 & TRB_IOC ? 'I' : 'i',
+			       field3 & TRB_CHAIN ? 'C' : 'c',
+			       field3 & TRB_ENT ? 'E' : 'e',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_NORMAL:
 	case TRB_ISOC:
 	case TRB_EVENT_DATA:
 	case TRB_TR_NOOP:
-		ret += snprintf(str, size,
-				"type '%s' Buffer %08x%08x length %ld "
-				"TD size %ld intr %ld "
-				"flags %c:%c:%c:%c:%c:%c:%c:%c:%c",
-				cdnsp_trb_type_string(type),
-				field1, field0, TRB_LEN(field2),
-				GET_TD_SIZE(field2),
-				GET_INTR_TARGET(field2),
-				field3 & TRB_BEI ? 'B' : 'b',
-				field3 & TRB_IDT ? 'T' : 't',
-				field3 & TRB_IOC ? 'I' : 'i',
-				field3 & TRB_CHAIN ? 'C' : 'c',
-				field3 & TRB_NO_SNOOP ? 'S' : 's',
-				field3 & TRB_ISP ? 'I' : 'i',
-				field3 & TRB_ENT ? 'E' : 'e',
-				field3 & TRB_CYCLE ? 'C' : 'c',
-				!(field3 & TRB_EVENT_INVALIDATE) ? 'V' : 'v');
+		ret = snprintf(str, size,
+			       "type '%s' Buffer %08x%08x length %ld "
+			       "TD size %ld intr %ld "
+			       "flags %c:%c:%c:%c:%c:%c:%c:%c:%c",
+			       cdnsp_trb_type_string(type),
+			       field1, field0, TRB_LEN(field2),
+			       GET_TD_SIZE(field2),
+			       GET_INTR_TARGET(field2),
+			       field3 & TRB_BEI ? 'B' : 'b',
+			       field3 & TRB_IDT ? 'T' : 't',
+			       field3 & TRB_IOC ? 'I' : 'i',
+			       field3 & TRB_CHAIN ? 'C' : 'c',
+			       field3 & TRB_NO_SNOOP ? 'S' : 's',
+			       field3 & TRB_ISP ? 'I' : 'i',
+			       field3 & TRB_ENT ? 'E' : 'e',
+			       field3 & TRB_CYCLE ? 'C' : 'c',
+			       !(field3 & TRB_EVENT_INVALIDATE) ? 'V' : 'v');
 		break;
 	case TRB_CMD_NOOP:
 	case TRB_ENABLE_SLOT:
-		ret += snprintf(str, size, "%s: flags %c",
-				cdnsp_trb_type_string(type),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size, "%s: flags %c",
+			       cdnsp_trb_type_string(type),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_DISABLE_SLOT:
-		ret += snprintf(str, size, "%s: slot %ld flags %c",
-				cdnsp_trb_type_string(type),
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size, "%s: slot %ld flags %c",
+			       cdnsp_trb_type_string(type),
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_ADDR_DEV:
-		ret += snprintf(str, size,
-				"%s: ctx %08x%08x slot %ld flags %c:%c",
-				cdnsp_trb_type_string(type), field1, field0,
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_BSR ? 'B' : 'b',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ctx %08x%08x slot %ld flags %c:%c",
+			       cdnsp_trb_type_string(type), field1, field0,
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_BSR ? 'B' : 'b',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_CONFIG_EP:
-		ret += snprintf(str, size,
-				"%s: ctx %08x%08x slot %ld flags %c:%c",
-				cdnsp_trb_type_string(type), field1, field0,
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_DC ? 'D' : 'd',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ctx %08x%08x slot %ld flags %c:%c",
+			       cdnsp_trb_type_string(type), field1, field0,
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_DC ? 'D' : 'd',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_EVAL_CONTEXT:
-		ret += snprintf(str, size,
-				"%s: ctx %08x%08x slot %ld flags %c",
-				cdnsp_trb_type_string(type), field1, field0,
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ctx %08x%08x slot %ld flags %c",
+			       cdnsp_trb_type_string(type), field1, field0,
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_RESET_EP:
 	case TRB_HALT_ENDPOINT:
 	case TRB_FLUSH_ENDPOINT:
-		ret += snprintf(str, size,
-				"%s: ep%d%s(%d) ctx %08x%08x slot %ld flags %c",
-				cdnsp_trb_type_string(type),
-				ep_num, ep_id % 2 ? "out" : "in",
-				TRB_TO_EP_INDEX(field3), field1, field0,
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ep%d%s(%d) ctx %08x%08x slot %ld flags %c",
+			       cdnsp_trb_type_string(type),
+			       ep_num, ep_id % 2 ? "out" : "in",
+			       TRB_TO_EP_INDEX(field3), field1, field0,
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_STOP_RING:
-		ret += snprintf(str, size,
-				"%s: ep%d%s(%d) slot %ld sp %d flags %c",
-				cdnsp_trb_type_string(type),
-				ep_num, ep_id % 2 ? "out" : "in",
-				TRB_TO_EP_INDEX(field3),
-				TRB_TO_SLOT_ID(field3),
-				TRB_TO_SUSPEND_PORT(field3),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ep%d%s(%d) slot %ld sp %d flags %c",
+			       cdnsp_trb_type_string(type),
+			       ep_num, ep_id % 2 ? "out" : "in",
+			       TRB_TO_EP_INDEX(field3),
+			       TRB_TO_SLOT_ID(field3),
+			       TRB_TO_SUSPEND_PORT(field3),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_SET_DEQ:
-		ret += snprintf(str, size,
-				"%s: ep%d%s(%d) deq %08x%08x stream %ld slot %ld  flags %c",
-				cdnsp_trb_type_string(type),
-				ep_num, ep_id % 2 ? "out" : "in",
-				TRB_TO_EP_INDEX(field3), field1, field0,
-				TRB_TO_STREAM_ID(field2),
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ep%d%s(%d) deq %08x%08x stream %ld slot %ld  flags %c",
+			       cdnsp_trb_type_string(type),
+			       ep_num, ep_id % 2 ? "out" : "in",
+			       TRB_TO_EP_INDEX(field3), field1, field0,
+			       TRB_TO_STREAM_ID(field2),
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_RESET_DEV:
-		ret += snprintf(str, size, "%s: slot %ld flags %c",
-				cdnsp_trb_type_string(type),
-				TRB_TO_SLOT_ID(field3),
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size, "%s: slot %ld flags %c",
+			       cdnsp_trb_type_string(type),
+			       TRB_TO_SLOT_ID(field3),
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_ENDPOINT_NRDY:
-		temp  = TRB_TO_HOST_STREAM(field2);
+		temp = TRB_TO_HOST_STREAM(field2);
 
-		ret += snprintf(str, size,
-				"%s: ep%d%s(%d) H_SID %x%s%s D_SID %lx flags %c:%c",
-				cdnsp_trb_type_string(type),
-				ep_num, ep_id % 2 ? "out" : "in",
-				TRB_TO_EP_INDEX(field3), temp,
-				temp == STREAM_PRIME_ACK ? "(PRIME)" : "",
-				temp == STREAM_REJECTED ? "(REJECTED)" : "",
-				TRB_TO_DEV_STREAM(field0),
-				field3 & TRB_STAT ? 'S' : 's',
-				field3 & TRB_CYCLE ? 'C' : 'c');
+		ret = snprintf(str, size,
+			       "%s: ep%d%s(%d) H_SID %x%s%s D_SID %lx flags %c:%c",
+			       cdnsp_trb_type_string(type),
+			       ep_num, ep_id % 2 ? "out" : "in",
+			       TRB_TO_EP_INDEX(field3), temp,
+			       temp == STREAM_PRIME_ACK ? "(PRIME)" : "",
+			       temp == STREAM_REJECTED ? "(REJECTED)" : "",
+			       TRB_TO_DEV_STREAM(field0),
+			       field3 & TRB_STAT ? 'S' : 's',
+			       field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	default:
-		ret += snprintf(str, size,
-				"type '%s' -> raw %08x %08x %08x %08x",
-				cdnsp_trb_type_string(type),
-				field0, field1, field2, field3);
+		ret = snprintf(str, size,
+			       "type '%s' -> raw %08x %08x %08x %08x",
+			       cdnsp_trb_type_string(type),
+			       field0, field1, field2, field3);
 	}
 
+	if (ret >= size)
+		pr_info("CDNSP: buffer overflowed.\n");
+
 	return str;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-ep0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-ep0.c
@@ -403,20 +403,6 @@
 	case USB_REQ_SET_ISOCH_DELAY:
 		ret = cdnsp_ep0_set_isoch_delay(pdev, ctrl);
 		break;
-	case USB_REQ_SET_INTERFACE:
-		/*
-		 * Add request into pending list to block sending status stage
-		 * by libcomposite.
-		 */
-		list_add_tail(&pdev->ep0_preq.list,
-			      &pdev->ep0_preq.pep->pending_list);
-
-		ret = cdnsp_ep0_delegate_req(pdev, ctrl);
-		if (ret == -EBUSY)
-			ret = 0;
-
-		list_del(&pdev->ep0_preq.list);
-		break;
 	default:
 		ret = cdnsp_ep0_delegate_req(pdev, ctrl);
 		break;
@@ -428,7 +414,7 @@
 void cdnsp_setup_analyze(struct cdnsp_device *pdev)
 {
 	struct usb_ctrlrequest *ctrl = &pdev->setup;
-	int ret = 0;
+	int ret = -EINVAL;
 	u16 len;
 
 	trace_cdnsp_ctrl_req(ctrl);
@@ -438,7 +424,6 @@
 
 	if (pdev->gadget.state == USB_STATE_NOTATTACHED) {
 		dev_err(pdev->dev, "ERR: Setup detected in unattached state\n");
-		ret = -EINVAL;
 		goto out;
 	}
 
@@ -474,9 +459,6 @@
 	else
 		ret = cdnsp_ep0_delegate_req(pdev, ctrl);
 
-	if (!len)
-		pdev->ep0_stage = CDNSP_STATUS_STAGE;
-
 	if (ret == USB_GADGET_DELAYED_STATUS) {
 		trace_cdnsp_ep0_status_stage("delayed");
 		return;
@@ -484,6 +466,6 @@
 out:
 	if (ret < 0)
 		cdnsp_ep0_stall(pdev);
-	else if (pdev->ep0_stage == CDNSP_STATUS_STAGE)
+	else if (!len && pdev->ep0_stage != CDNSP_STATUS_STAGE)
 		cdnsp_status_stage(pdev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-gadget.c
@@ -600,11 +600,11 @@
 
 	trace_cdnsp_ep_halt(value ? "Set" : "Clear");
 
-	if (value) {
-		ret = cdnsp_cmd_stop_ep(pdev, pep);
-		if (ret)
-			return ret;
+	ret = cdnsp_cmd_stop_ep(pdev, pep);
+	if (ret)
+		return ret;
 
+	if (value) {
 		if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_STOPPED) {
 			cdnsp_queue_halt_endpoint(pdev, pep->idx);
 			cdnsp_ring_cmd_db(pdev);
@@ -613,10 +613,6 @@
 
 		pep->ep_state |= EP_HALTED;
 	} else {
-		/*
-		 * In device mode driver can call reset endpoint command
-		 * from any endpoint state.
-		 */
 		cdnsp_queue_reset_ep(pdev, pep->idx);
 		cdnsp_ring_cmd_db(pdev);
 		ret = cdnsp_wait_for_cmd_compl(pdev);
@@ -1129,6 +1125,9 @@
 	unsigned long flags;
 	int ret;
 
+	if (request->status != -EINPROGRESS)
+		return 0;
+
 	if (!pep->endpoint.desc) {
 		dev_err(pdev->dev,
 			"%s: can't dequeue to disabled endpoint\n",
@@ -1541,15 +1540,27 @@
 {
 	struct cdnsp_device *pdev = gadget_to_cdnsp(gadget);
 	struct cdns *cdns = dev_get_drvdata(pdev->dev);
+	unsigned long flags;
 
 	trace_cdnsp_pullup(is_on);
 
+	/*
+	 * Disable events handling while controller is being
+	 * enabled/disabled.
+	 */
+	disable_irq(cdns->dev_irq);
+	spin_lock_irqsave(&pdev->lock, flags);
+
 	if (!is_on) {
 		cdnsp_reset_device(pdev);
 		cdns_clear_vbus(cdns);
 	} else {
 		cdns_set_vbus(cdns);
 	}
+
+	spin_unlock_irqrestore(&pdev->lock, flags);
+	enable_irq(cdns->dev_irq);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-gadget.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-gadget.h
@@ -811,6 +811,7 @@
  *        generate Missed Service Error Event.
  *        Set skip flag when receive a Missed Service Error Event and
  *        process the missed tds on the endpoint ring.
+ * @wa1_nop_trb: hold pointer to NOP trb.
  */
 struct cdnsp_ep {
 	struct usb_ep endpoint;
@@ -838,6 +839,8 @@
 #define EP_UNCONFIGURED		BIT(7)
 
 	bool skip;
+	union cdnsp_trb	 *wa1_nop_trb;
+
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-mem.c
@@ -987,6 +987,9 @@
 
 	/* Set up the endpoint ring. */
 	pep->ring = cdnsp_ring_alloc(pdev, 2, ring_type, max_packet, mem_flags);
+	if (!pep->ring)
+		return -ENOMEM;
+
 	pep->skip = false;
 
 	/* Fill the endpoint context */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-pci.c
@@ -29,30 +29,23 @@
 #define PLAT_DRIVER_NAME	"cdns-usbssp"
 
 #define CDNS_VENDOR_ID		0x17cd
-#define CDNS_DEVICE_ID		0x0100
+#define CDNS_DEVICE_ID		0x0200
+#define CDNS_DRD_ID		0x0100
 #define CDNS_DRD_IF		(PCI_CLASS_SERIAL_USB << 8 | 0x80)
 
 static struct pci_dev *cdnsp_get_second_fun(struct pci_dev *pdev)
 {
-	struct pci_dev *func;
-
 	/*
 	 * Gets the second function.
-	 * It's little tricky, but this platform has two function.
-	 * The fist keeps resources for Host/Device while the second
-	 * keeps resources for DRD/OTG.
+	 * Platform has two function. The fist keeps resources for
+	 * Host/Device while the secon keeps resources for DRD/OTG.
 	 */
-	func = pci_get_device(pdev->vendor, pdev->device, NULL);
-	if (!func)
-		return NULL;
+	if (pdev->device == CDNS_DEVICE_ID)
+		return  pci_get_device(pdev->vendor, CDNS_DRD_ID, NULL);
+	else if (pdev->device == CDNS_DRD_ID)
+		return pci_get_device(pdev->vendor, CDNS_DEVICE_ID, NULL);
 
-	if (func->devfn == pdev->devfn) {
-		func = pci_get_device(pdev->vendor, pdev->device, func);
-		if (!func)
-			return NULL;
-	}
-
-	return func;
+	return NULL;
 }
 
 static int cdnsp_pci_probe(struct pci_dev *pdev,
@@ -217,8 +210,9 @@
 	int ret;
 
 	spin_lock_irqsave(&cdns->lock, flags);
-	ret = cdns_resume(cdns, 1);
+	ret = cdns_resume(cdns);
 	spin_unlock_irqrestore(&cdns->lock, flags);
+	cdns_set_active(cdns, 1);
 
 	return ret;
 }
@@ -232,6 +226,8 @@
 	  PCI_CLASS_SERIAL_USB_DEVICE, PCI_ANY_ID },
 	{ PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
 	  CDNS_DRD_IF, PCI_ANY_ID },
+	{ PCI_VENDOR_ID_CDNS, CDNS_DRD_ID, PCI_ANY_ID, PCI_ANY_ID,
+	  CDNS_DRD_IF, PCI_ANY_ID },
 	{ 0, }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-ring.c
@@ -402,7 +402,7 @@
 	struct cdnsp_stream_ctx *st_ctx;
 	struct cdnsp_ep *pep;
 
-	pep = &pdev->eps[stream_id];
+	pep = &pdev->eps[ep_index];
 
 	if (pep->ep_state & EP_HAS_STREAMS) {
 		st_ctx = &pep->stream_info.stream_ctx_array[stream_id];
@@ -718,7 +718,8 @@
 	seg = cdnsp_trb_in_td(pdev, cur_td->start_seg, cur_td->first_trb,
 			      cur_td->last_trb, hw_deq);
 
-	if (seg && (pep->ep_state & EP_ENABLED))
+	if (seg && (pep->ep_state & EP_ENABLED) &&
+	    !(pep->ep_state & EP_DIS_IN_RROGRESS))
 		cdnsp_find_new_dequeue_state(pdev, pep, preq->request.stream_id,
 					     cur_td, &deq_state);
 	else
@@ -736,7 +737,8 @@
 	 * During disconnecting all endpoint will be disabled so we don't
 	 * have to worry about updating dequeue pointer.
 	 */
-	if (pdev->cdnsp_state & CDNSP_STATE_DISCONNECT_PENDING) {
+	if (pdev->cdnsp_state & CDNSP_STATE_DISCONNECT_PENDING ||
+	    pep->ep_state & EP_DIS_IN_RROGRESS) {
 		status = -ESHUTDOWN;
 		ret = cdnsp_cmd_set_deq(pdev, pep, &deq_state);
 	}
@@ -1029,6 +1031,8 @@
 		return;
 	}
 
+	*status = 0;
+
 	cdnsp_finish_td(pdev, td, event, pep, status);
 }
 
@@ -1520,11 +1524,20 @@
 	unsigned long flags;
 	int counter = 0;
 
+	local_bh_disable();
 	spin_lock_irqsave(&pdev->lock, flags);
 
 	if (pdev->cdnsp_state & (CDNSP_STATE_HALTED | CDNSP_STATE_DYING)) {
-		cdnsp_died(pdev);
+		/*
+		 * While removing or stopping driver there may still be deferred
+		 * not handled interrupt which should not be treated as error.
+		 * Driver should simply ignore it.
+		 */
+		if (pdev->gadget_driver)
+			cdnsp_died(pdev);
+
 		spin_unlock_irqrestore(&pdev->lock, flags);
+		local_bh_enable();
 		return IRQ_HANDLED;
 	}
 
@@ -1541,6 +1554,7 @@
 	cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1);
 
 	spin_unlock_irqrestore(&pdev->lock, flags);
+	local_bh_enable();
 
 	return IRQ_HANDLED;
 }
@@ -1754,10 +1768,15 @@
 			      int trb_buff_len,
 			      unsigned int td_total_len,
 			      struct cdnsp_request *preq,
-			      bool more_trbs_coming)
+			      bool more_trbs_coming,
+			      bool zlp)
 {
 	u32 maxp, total_packet_count;
 
+	/* Before ZLP driver needs set TD_SIZE = 1. */
+	if (zlp)
+		return 1;
+
 	/* One TRB with a zero-length data packet. */
 	if (!more_trbs_coming || (transferred == 0 && trb_buff_len == 0) ||
 	    trb_buff_len == td_total_len)
@@ -1886,6 +1905,23 @@
 		return ret;
 
 	/*
+	 * workaround 1: STOP EP command on LINK TRB with TC bit set to 1
+	 * causes that internal cycle bit can have incorrect state after
+	 * command complete. In consequence empty transfer ring can be
+	 * incorrectly detected when EP is resumed.
+	 * NOP TRB before LINK TRB avoid such scenario. STOP EP command is
+	 * then on NOP TRB and internal cycle bit is not changed and have
+	 * correct value.
+	 */
+	if (pep->wa1_nop_trb) {
+		field = le32_to_cpu(pep->wa1_nop_trb->trans_event.flags);
+		field ^= TRB_CYCLE;
+
+		pep->wa1_nop_trb->trans_event.flags = cpu_to_le32(field);
+		pep->wa1_nop_trb = NULL;
+	}
+
+	/*
 	 * Don't give the first TRB to the hardware (by toggling the cycle bit)
 	 * until we've finished creating all the other TRBs. The ring's cycle
 	 * state may change as we enqueue the other TRBs, so save it too.
@@ -1932,13 +1968,16 @@
 		}
 
 		if (enqd_len + trb_buff_len >= full_len) {
-			if (need_zero_pkt)
-				zero_len_trb = !zero_len_trb;
-
-			field &= ~TRB_CHAIN;
-			field |= TRB_IOC;
-			more_trbs_coming = false;
-			preq->td.last_trb = ring->enqueue;
+			if (need_zero_pkt && !zero_len_trb) {
+				zero_len_trb = true;
+			} else {
+				zero_len_trb = false;
+				field &= ~TRB_CHAIN;
+				field |= TRB_IOC;
+				more_trbs_coming = false;
+				need_zero_pkt = false;
+				preq->td.last_trb = ring->enqueue;
+			}
 		}
 
 		/* Only set interrupt on short packet for OUT endpoints. */
@@ -1948,12 +1987,13 @@
 		/* Set the TRB length, TD size, and interrupter fields. */
 		remainder = cdnsp_td_remainder(pdev, enqd_len, trb_buff_len,
 					       full_len, preq,
-					       more_trbs_coming);
+					       more_trbs_coming,
+					       zero_len_trb);
 
 		length_field = TRB_LEN(trb_buff_len) | TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
-		cdnsp_queue_trb(pdev, ring, more_trbs_coming | zero_len_trb,
+		cdnsp_queue_trb(pdev, ring, more_trbs_coming,
 				lower_32_bits(send_addr),
 				upper_32_bits(send_addr),
 				length_field,
@@ -1976,6 +2016,17 @@
 		send_addr = addr;
 	}
 
+	if (cdnsp_trb_is_link(ring->enqueue + 1)) {
+		field = TRB_TYPE(TRB_TR_NOOP) | TRB_IOC;
+		if (!ring->cycle_state)
+			field |= TRB_CYCLE;
+
+		pep->wa1_nop_trb = ring->enqueue;
+
+		cdnsp_queue_trb(pdev, ring, 0, 0x0, 0x0,
+				TRB_INTR_TARGET(0), field);
+	}
+
 	cdnsp_check_trb_math(preq, enqd_len);
 	ret = cdnsp_giveback_first_trb(pdev, pep, preq->request.stream_id,
 				       start_cycle, start_trb);
@@ -1988,10 +2039,11 @@
 
 int cdnsp_queue_ctrl_tx(struct cdnsp_device *pdev, struct cdnsp_request *preq)
 {
-	u32 field, length_field, remainder;
+	u32 field, length_field, zlp = 0;
 	struct cdnsp_ep *pep = preq->pep;
 	struct cdnsp_ring *ep_ring;
 	int num_trbs;
+	u32 maxp;
 	int ret;
 
 	ep_ring = cdnsp_request_to_transfer_ring(pdev, preq);
@@ -2001,26 +2053,33 @@
 	/* 1 TRB for data, 1 for status */
 	num_trbs = (pdev->three_stage_setup) ? 2 : 1;
 
+	maxp = usb_endpoint_maxp(pep->endpoint.desc);
+
+	if (preq->request.zero && preq->request.length &&
+	    (preq->request.length % maxp == 0)) {
+		num_trbs++;
+		zlp = 1;
+	}
+
 	ret = cdnsp_prepare_transfer(pdev, preq, num_trbs);
 	if (ret)
 		return ret;
 
 	/* If there's data, queue data TRBs */
-	if (pdev->ep0_expect_in)
-		field = TRB_TYPE(TRB_DATA) | TRB_IOC;
-	else
-		field = TRB_ISP | TRB_TYPE(TRB_DATA) | TRB_IOC;
-
 	if (preq->request.length > 0) {
-		remainder = cdnsp_td_remainder(pdev, 0, preq->request.length,
-					       preq->request.length, preq, 1);
+		field = TRB_TYPE(TRB_DATA);
 
-		length_field = TRB_LEN(preq->request.length) |
-				TRB_TD_SIZE(remainder) | TRB_INTR_TARGET(0);
+		if (zlp)
+			field |= TRB_CHAIN;
+		else
+			field |= TRB_IOC | (pdev->ep0_expect_in ? 0 : TRB_ISP);
 
 		if (pdev->ep0_expect_in)
 			field |= TRB_DIR_IN;
 
+		length_field = TRB_LEN(preq->request.length) |
+			       TRB_TD_SIZE(zlp) | TRB_INTR_TARGET(0);
+
 		cdnsp_queue_trb(pdev, ep_ring, true,
 				lower_32_bits(preq->request.dma),
 				upper_32_bits(preq->request.dma), length_field,
@@ -2028,6 +2087,20 @@
 				TRB_SETUPID(pdev->setup_id) |
 				pdev->setup_speed);
 
+		if (zlp) {
+			field = TRB_TYPE(TRB_NORMAL) | TRB_IOC;
+
+			if (!pdev->ep0_expect_in)
+				field = TRB_ISP;
+
+			cdnsp_queue_trb(pdev, ep_ring, true,
+					lower_32_bits(preq->request.dma),
+					upper_32_bits(preq->request.dma), 0,
+					field | ep_ring->cycle_state |
+					TRB_SETUPID(pdev->setup_id) |
+					pdev->setup_speed);
+		}
+
 		pdev->ep0_stage = CDNSP_DATA_STAGE;
 	}
 
@@ -2064,7 +2137,8 @@
 	u32 ep_state = GET_EP_CTX_STATE(pep->out_ctx);
 	int ret = 0;
 
-	if (ep_state == EP_STATE_STOPPED || ep_state == EP_STATE_DISABLED) {
+	if (ep_state == EP_STATE_STOPPED || ep_state == EP_STATE_DISABLED ||
+	    ep_state == EP_STATE_HALTED) {
 		trace_cdnsp_ep_stopped_or_disabled(pep->out_ctx);
 		goto ep_stopped;
 	}
@@ -2213,7 +2287,7 @@
 		/* Set the TRB length, TD size, & interrupter fields. */
 		remainder = cdnsp_td_remainder(pdev, running_total,
 					       trb_buff_len, td_len, preq,
-					       more_trbs_coming);
+					       more_trbs_coming, 0);
 
 		length_field = TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/cdnsp-trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/cdnsp-trace.h
@@ -57,9 +57,9 @@
 		__entry->first_prime_det = pep->stream_info.first_prime_det;
 		__entry->drbls_count = pep->stream_info.drbls_count;
 	),
-	TP_printk("%s: SID: %08x ep state: %x stream: enabled: %d num  %d "
+	TP_printk("%s: SID: %08x, ep state: %x, stream: enabled: %d num %d "
 		  "tds %d, first prime: %d drbls %d",
-		  __get_str(name), __entry->state, __entry->stream_id,
+		  __get_str(name), __entry->stream_id, __entry->state,
 		  __entry->enabled, __entry->num_streams, __entry->td_count,
 		  __entry->first_prime_det, __entry->drbls_count)
 );
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/core.c
@@ -394,7 +394,6 @@
 	return ret;
 }
 
-
 /**
  * cdns_wakeup_irq - interrupt handler for wakeup events
  * @irq: irq number for cdns3/cdnsp core device
@@ -522,9 +521,8 @@
 }
 EXPORT_SYMBOL_GPL(cdns_suspend);
 
-int cdns_resume(struct cdns *cdns, u8 set_active)
+int cdns_resume(struct cdns *cdns)
 {
-	struct device *dev = cdns->dev;
 	enum usb_role real_role;
 	bool role_changed = false;
 	int ret = 0;
@@ -556,15 +554,23 @@
 	if (cdns->roles[cdns->role]->resume)
 		cdns->roles[cdns->role]->resume(cdns, cdns_power_is_lost(cdns));
 
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cdns_resume);
+
+void cdns_set_active(struct cdns *cdns, u8 set_active)
+{
+	struct device *dev = cdns->dev;
+
 	if (set_active) {
 		pm_runtime_disable(dev);
 		pm_runtime_set_active(dev);
 		pm_runtime_enable(dev);
 	}
 
-	return 0;
+	return;
 }
-EXPORT_SYMBOL_GPL(cdns_resume);
+EXPORT_SYMBOL_GPL(cdns_set_active);
 #endif /* CONFIG_PM_SLEEP */
 
 MODULE_AUTHOR("Peter Chen <peter.chen@nxp.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/core.h
@@ -44,6 +44,7 @@
 			bool suspend, bool wakeup);
 	unsigned long quirks;
 #define CDNS3_DEFAULT_PM_RUNTIME_ALLOW	BIT(0)
+#define CDNS3_DRD_SUSPEND_RESIDENCY_ENABLE	BIT(1)
 };
 
 /**
@@ -125,11 +126,13 @@
 int cdns_remove(struct cdns *cdns);
 
 #ifdef CONFIG_PM_SLEEP
-int cdns_resume(struct cdns *cdns, u8 set_active);
+int cdns_resume(struct cdns *cdns);
 int cdns_suspend(struct cdns *cdns);
+void cdns_set_active(struct cdns *cdns, u8 set_active);
 #else /* CONFIG_PM_SLEEP */
-static inline int cdns_resume(struct cdns *cdns, u8 set_active)
+static inline int cdns_resume(struct cdns *cdns)
 { return 0; }
+static inline void cdns_set_active(struct cdns *cdns, u8 set_active) { }
 static inline int cdns_suspend(struct cdns *cdns)
 { return 0; }
 #endif /* CONFIG_PM_SLEEP */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/drd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/drd.c
@@ -156,7 +156,8 @@
  */
 static void cdns_otg_disable_irq(struct cdns *cdns)
 {
-	writel(0, &cdns->otg_irq_regs->ien);
+	if (cdns->version)
+		writel(0, &cdns->otg_irq_regs->ien);
 }
 
 /**
@@ -384,7 +385,7 @@
 int cdns_drd_init(struct cdns *cdns)
 {
 	void __iomem *regs;
-	u32 state;
+	u32 state, reg;
 	int ret;
 
 	regs = devm_ioremap_resource(cdns->dev, &cdns->otg_res);
@@ -418,15 +419,28 @@
 
 		cdns->otg_regs = (void __iomem *)&cdns->otg_v1_regs->cmd;
 
-		if (readl(&cdns->otg_cdnsp_regs->did) == OTG_CDNSP_DID) {
+		state = readl(&cdns->otg_cdnsp_regs->did);
+
+		if (OTG_CDNSP_CHECK_DID(state)) {
 			cdns->otg_irq_regs = (struct cdns_otg_irq_regs __iomem *)
 					      &cdns->otg_cdnsp_regs->ien;
 			cdns->version  = CDNSP_CONTROLLER_V2;
-		} else {
+		} else if (OTG_CDNS3_CHECK_DID(state)) {
 			cdns->otg_irq_regs = (struct cdns_otg_irq_regs __iomem *)
 					      &cdns->otg_v1_regs->ien;
 			writel(1, &cdns->otg_v1_regs->simulate);
+
+			if (cdns->pdata &&
+			    (cdns->pdata->quirks & CDNS3_DRD_SUSPEND_RESIDENCY_ENABLE)) {
+				reg = readl(&cdns->otg_v1_regs->susp_ctrl);
+				reg |= SUSP_CTRL_SUSPEND_RESIDENCY_ENABLE;
+				writel(reg, &cdns->otg_v1_regs->susp_ctrl);
+			}
+
 			cdns->version  = CDNS3_CONTROLLER_V1;
+		} else {
+			dev_err(cdns->dev, "not supporte DID=0x%08x\n", state);
+			return -EINVAL;
 		}
 
 		dev_dbg(cdns->dev, "DRD version v1 (ID: %08x, rev: %08x)\n",
@@ -479,15 +493,14 @@
 	return 0;
 }
 
-
 /* Indicate the cdns3 core was power lost before */
 bool cdns_power_is_lost(struct cdns *cdns)
 {
-	if (cdns->version == CDNS3_CONTROLLER_V1) {
-		if (!(readl(&cdns->otg_v1_regs->simulate) & BIT(0)))
+	if (cdns->version == CDNS3_CONTROLLER_V0) {
+		if (!(readl(&cdns->otg_v0_regs->simulate) & BIT(0)))
 			return true;
 	} else {
-		if (!(readl(&cdns->otg_v0_regs->simulate) & BIT(0)))
+		if (!(readl(&cdns->otg_v1_regs->simulate) & BIT(0)))
 			return true;
 	}
 	return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/drd.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/drd.h
@@ -79,7 +79,11 @@
 	__le32 susp_timing_ctrl;
 };
 
-#define OTG_CDNSP_DID	0x0004034E
+/* CDNSP driver supports 0x000403xx Cadence USB controller family. */
+#define OTG_CDNSP_CHECK_DID(did) (((did) & GENMASK(31, 8)) == 0x00040300)
+
+/* CDNS3 driver supports 0x000402xx Cadence USB controller family. */
+#define OTG_CDNS3_CHECK_DID(did) (((did) & GENMASK(31, 8)) == 0x00040200)
 
 /*
  * Common registers interface for both CDNS3 and CDNSP version of DRD.
@@ -189,6 +193,9 @@
 /* OTGREFCLK - bitmasks */
 #define OTGREFCLK_STB_CLK_SWITCH_EN	BIT(31)
 
+/* SUPS_CTRL - bitmasks */
+#define SUSP_CTRL_SUSPEND_RESIDENCY_ENABLE	BIT(17)
+
 /* OVERRIDE - bitmasks */
 #define OVERRIDE_IDPULLUP		BIT(0)
 /* Only for CDNS3_CONTROLLER_V0 version */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/cdns3/host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/cdns3/host.c
@@ -17,17 +17,52 @@
 #include "../host/xhci.h"
 #include "../host/xhci-plat.h"
 
+/*
+ * The XECP_PORT_CAP_REG and XECP_AUX_CTRL_REG1 exist only
+ * in Cadence USB3 dual-role controller, so it can't be used
+ * with Cadence CDNSP dual-role controller.
+ */
 #define XECP_PORT_CAP_REG	0x8000
 #define XECP_AUX_CTRL_REG1	0x8120
 
 #define CFG_RXDET_P3_EN		BIT(15)
 #define LPM_2_STB_SWITCH_EN	BIT(25)
 
-static int xhci_cdns3_suspend_quirk(struct usb_hcd *hcd);
+static void xhci_cdns3_plat_start(struct usb_hcd *hcd)
+{
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+	u32 value;
+
+	/* set usbcmd.EU3S */
+	value = readl(&xhci->op_regs->command);
+	value |= CMD_PM_INDEX;
+	writel(value, &xhci->op_regs->command);
+
+	if (hcd->regs) {
+		value = readl(hcd->regs + XECP_AUX_CTRL_REG1);
+		value |= CFG_RXDET_P3_EN;
+		writel(value, hcd->regs + XECP_AUX_CTRL_REG1);
+
+		value = readl(hcd->regs + XECP_PORT_CAP_REG);
+		value |= LPM_2_STB_SWITCH_EN;
+		writel(value, hcd->regs + XECP_PORT_CAP_REG);
+	}
+}
+
+static int xhci_cdns3_resume_quirk(struct usb_hcd *hcd)
+{
+	xhci_cdns3_plat_start(hcd);
+	return 0;
+}
 
 static const struct xhci_plat_priv xhci_plat_cdns3_xhci = {
 	.quirks = XHCI_SKIP_PHY_INIT | XHCI_AVOID_BEI,
-	.suspend_quirk = xhci_cdns3_suspend_quirk,
+	.plat_start = xhci_cdns3_plat_start,
+	.resume_quirk = xhci_cdns3_resume_quirk,
+};
+
+static const struct xhci_plat_priv xhci_plat_cdnsp_xhci = {
+	.quirks = XHCI_CDNS_SCTX_QUIRK,
 };
 
 static int __cdns_host_init(struct cdns *cdns)
@@ -54,8 +89,13 @@
 		goto err1;
 	}
 
-	cdns->xhci_plat_data = kmemdup(&xhci_plat_cdns3_xhci,
-			sizeof(struct xhci_plat_priv), GFP_KERNEL);
+	if (cdns->version < CDNSP_CONTROLLER_V2)
+		cdns->xhci_plat_data = kmemdup(&xhci_plat_cdns3_xhci,
+				sizeof(struct xhci_plat_priv), GFP_KERNEL);
+	else
+		cdns->xhci_plat_data = kmemdup(&xhci_plat_cdnsp_xhci,
+				sizeof(struct xhci_plat_priv), GFP_KERNEL);
+
 	if (!cdns->xhci_plat_data) {
 		ret = -ENOMEM;
 		goto err1;
@@ -89,32 +129,6 @@
 	return ret;
 }
 
-static int xhci_cdns3_suspend_quirk(struct usb_hcd *hcd)
-{
-	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	u32 value;
-
-	if (pm_runtime_status_suspended(hcd->self.controller))
-		return 0;
-
-	/* set usbcmd.EU3S */
-	value = readl(&xhci->op_regs->command);
-	value |= CMD_PM_INDEX;
-	writel(value, &xhci->op_regs->command);
-
-	if (hcd->regs) {
-		value = readl(hcd->regs + XECP_AUX_CTRL_REG1);
-		value |= CFG_RXDET_P3_EN;
-		writel(value, hcd->regs + XECP_AUX_CTRL_REG1);
-
-		value = readl(hcd->regs + XECP_PORT_CAP_REG);
-		value |= LPM_2_STB_SWITCH_EN;
-		writel(value, hcd->regs + XECP_PORT_CAP_REG);
-	}
-
-	return 0;
-}
-
 static void cdns_host_exit(struct cdns *cdns)
 {
 	kfree(cdns->xhci_plat_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/ci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/ci.h
@@ -203,6 +203,7 @@
  * @in_lpm: if the core in low power mode
  * @wakeup_int: if wakeup interrupt occur
  * @rev: The revision number for controller
+ * @mutex: protect code from concorrent running when doing role switch
  */
 struct ci_hdrc {
 	struct device			*dev;
@@ -255,6 +256,7 @@
 	bool				in_lpm;
 	bool				wakeup_int;
 	enum ci_revision		rev;
+	struct mutex                    mutex;
 };
 
 static inline struct ci_role_driver *ci_role(struct ci_hdrc *ci)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/ci_hdrc_imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/ci_hdrc_imx.c
@@ -70,6 +70,10 @@
 		CI_HDRC_PMQOS,
 };
 
+static const struct ci_hdrc_imx_platform_flag imx8ulp_usb_data = {
+	.flags = CI_HDRC_SUPPORTS_RUNTIME_PM,
+};
+
 static const struct of_device_id ci_hdrc_imx_dt_ids[] = {
 	{ .compatible = "fsl,imx23-usb", .data = &imx23_usb_data},
 	{ .compatible = "fsl,imx28-usb", .data = &imx28_usb_data},
@@ -80,6 +84,7 @@
 	{ .compatible = "fsl,imx6ul-usb", .data = &imx6ul_usb_data},
 	{ .compatible = "fsl,imx7d-usb", .data = &imx7d_usb_data},
 	{ .compatible = "fsl,imx7ulp-usb", .data = &imx7ulp_usb_data},
+	{ .compatible = "fsl,imx8ulp-usb", .data = &imx8ulp_usb_data},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, ci_hdrc_imx_dt_ids);
@@ -170,10 +175,12 @@
 	if (of_usb_get_phy_mode(np) == USBPHY_INTERFACE_MODE_ULPI)
 		data->ulpi = 1;
 
-	of_property_read_u32(np, "samsung,picophy-pre-emp-curr-control",
-			&data->emp_curr_control);
-	of_property_read_u32(np, "samsung,picophy-dc-vol-level-adjust",
-			&data->dc_vol_level_adjust);
+	if (of_property_read_u32(np, "samsung,picophy-pre-emp-curr-control",
+			&data->emp_curr_control))
+		data->emp_curr_control = -1;
+	if (of_property_read_u32(np, "samsung,picophy-dc-vol-level-adjust",
+			&data->dc_vol_level_adjust))
+		data->dc_vol_level_adjust = -1;
 
 	return data;
 }
@@ -349,10 +356,9 @@
 		if (PTR_ERR(data->pinctrl) == -ENODEV)
 			data->pinctrl = NULL;
 		else if (IS_ERR(data->pinctrl)) {
-			if (PTR_ERR(data->pinctrl) != -EPROBE_DEFER)
-				dev_err(dev, "pinctrl get failed, err=%ld\n",
-					PTR_ERR(data->pinctrl));
-			return PTR_ERR(data->pinctrl);
+			ret = dev_err_probe(dev, PTR_ERR(data->pinctrl),
+					     "pinctrl get failed\n");
+			goto err_put;
 		}
 
 		data->hsic_pad_regulator =
@@ -361,11 +367,9 @@
 			/* no pad regualator is needed */
 			data->hsic_pad_regulator = NULL;
 		} else if (IS_ERR(data->hsic_pad_regulator)) {
-			if (PTR_ERR(data->hsic_pad_regulator) != -EPROBE_DEFER)
-				dev_err(dev,
-					"Get HSIC pad regulator error: %ld\n",
-					PTR_ERR(data->hsic_pad_regulator));
-			return PTR_ERR(data->hsic_pad_regulator);
+			ret = dev_err_probe(dev, PTR_ERR(data->hsic_pad_regulator),
+					     "Get HSIC pad regulator error\n");
+			goto err_put;
 		}
 
 		if (data->hsic_pad_regulator) {
@@ -373,7 +377,7 @@
 			if (ret) {
 				dev_err(dev,
 					"Failed to enable HSIC pad regulator\n");
-				return ret;
+				goto err_put;
 			}
 		}
 	}
@@ -387,13 +391,14 @@
 			dev_err(dev,
 				"pinctrl_hsic_idle lookup failed, err=%ld\n",
 					PTR_ERR(pinctrl_hsic_idle));
-			return PTR_ERR(pinctrl_hsic_idle);
+			ret = PTR_ERR(pinctrl_hsic_idle);
+			goto err_put;
 		}
 
 		ret = pinctrl_select_state(data->pinctrl, pinctrl_hsic_idle);
 		if (ret) {
 			dev_err(dev, "hsic_idle select failed, err=%d\n", ret);
-			return ret;
+			goto err_put;
 		}
 
 		data->pinctrl_hsic_active = pinctrl_lookup_state(data->pinctrl,
@@ -402,7 +407,8 @@
 			dev_err(dev,
 				"pinctrl_hsic_active lookup failed, err=%ld\n",
 					PTR_ERR(data->pinctrl_hsic_active));
-			return PTR_ERR(data->pinctrl_hsic_active);
+			ret = PTR_ERR(data->pinctrl_hsic_active);
+			goto err_put;
 		}
 	}
 
@@ -420,15 +426,15 @@
 	data->phy = devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0);
 	if (IS_ERR(data->phy)) {
 		ret = PTR_ERR(data->phy);
-		if (ret == -ENODEV) {
-			data->phy = devm_usb_get_phy_by_phandle(dev, "phys", 0);
-			if (IS_ERR(data->phy)) {
-				ret = PTR_ERR(data->phy);
-				if (ret == -ENODEV)
-					data->phy = NULL;
-				else
-					goto err_clk;
-			}
+		if (ret != -ENODEV)
+			goto err_clk;
+		data->phy = devm_usb_get_phy_by_phandle(dev, "phys", 0);
+		if (IS_ERR(data->phy)) {
+			ret = PTR_ERR(data->phy);
+			if (ret == -ENODEV)
+				data->phy = NULL;
+			else
+				goto err_clk;
 		}
 	}
 
@@ -458,9 +464,7 @@
 				&pdata);
 	if (IS_ERR(data->ci_pdev)) {
 		ret = PTR_ERR(data->ci_pdev);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "ci_hdrc_add_device failed, err=%d\n",
-					ret);
+		dev_err_probe(dev, ret, "ci_hdrc_add_device failed\n");
 		goto err_clk;
 	}
 
@@ -504,10 +508,12 @@
 	if (pdata.flags & CI_HDRC_PMQOS)
 		cpu_latency_qos_remove_request(&data->pm_qos_req);
 	data->ci_pdev = NULL;
+err_put:
+	put_device(data->usbmisc_data->dev);
 	return ret;
 }
 
-static int ci_hdrc_imx_remove(struct platform_device *pdev)
+static void ci_hdrc_imx_remove(struct platform_device *pdev)
 {
 	struct ci_hdrc_imx_data *data = platform_get_drvdata(pdev);
 
@@ -527,8 +533,7 @@
 		if (data->hsic_pad_regulator)
 			regulator_disable(data->hsic_pad_regulator);
 	}
-
-	return 0;
+	put_device(data->usbmisc_data->dev);
 }
 
 static void ci_hdrc_imx_shutdown(struct platform_device *pdev)
@@ -674,7 +679,7 @@
 };
 static struct platform_driver ci_hdrc_imx_driver = {
 	.probe = ci_hdrc_imx_probe,
-	.remove = ci_hdrc_imx_remove,
+	.remove_new = ci_hdrc_imx_remove,
 	.shutdown = ci_hdrc_imx_shutdown,
 	.driver = {
 		.name = "imx_usb",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/ci_hdrc_usb2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/ci_hdrc_usb2.c
@@ -30,6 +30,7 @@
 
 static const struct ci_hdrc_platform_data ci_zynq_pdata = {
 	.capoffset	= DEF_CAPOFFSET,
+	.flags          = CI_HDRC_PHY_VBUS_CONTROL,
 };
 
 static const struct ci_hdrc_platform_data ci_zevio_pdata = {
@@ -64,6 +65,10 @@
 	if (match && match->data) {
 		/* struct copy */
 		*ci_pdata = *(struct ci_hdrc_platform_data *)match->data;
+		ci_pdata->usb_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy",
+					 0);
+		if (IS_ERR(ci_pdata->usb_phy))
+			return PTR_ERR(ci_pdata->usb_phy);
 	}
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/core.c
@@ -324,7 +324,8 @@
 
 		ret = phy_power_on(ci->phy);
 		if (ret) {
-			phy_exit(ci->phy);
+			if (phy_exit(ci->phy) < 0)
+				dev_dbg(ci->dev, "phy exit failed\r\n");
 			return ret;
 		}
 	} else {
@@ -341,12 +342,20 @@
  */
 static void ci_usb_phy_exit(struct ci_hdrc *ci)
 {
+	int ret;
+
 	if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL)
 		return;
 
 	if (ci->phy) {
-		phy_power_off(ci->phy);
-		phy_exit(ci->phy);
+		ret = phy_power_off(ci->phy);
+		if (ret < 0)
+			dev_dbg(ci->dev, "phy poweroff failed\r\n");
+
+		ret = phy_exit(ci->phy);
+		if (ret < 0)
+			dev_dbg(ci->dev, "phy exit failed\r\n");
+
 	} else {
 		usb_phy_shutdown(ci->usb_phy);
 	}
@@ -514,13 +523,20 @@
 	return 0;
 }
 
-static irqreturn_t ci_irq(int irq, void *data)
+static irqreturn_t ci_irq_handler(int irq, void *data)
 {
 	struct ci_hdrc *ci = data;
 	irqreturn_t ret = IRQ_NONE;
 	u32 otgsc = 0;
 
 	if (ci->in_lpm) {
+		/*
+		 * If we already have a wakeup irq pending there,
+		 * let's just return to wait resume finished firstly.
+		 */
+		if (ci->wakeup_int)
+			return IRQ_HANDLED;
+
 		disable_irq_nosync(irq);
 		ci->wakeup_int = true;
 		pm_runtime_get(ci->dev);
@@ -567,6 +583,15 @@
 	return ret;
 }
 
+static void ci_irq(struct ci_hdrc *ci)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	ci_irq_handler(ci->irq, ci);
+	local_irq_restore(flags);
+}
+
 static int ci_cable_notifier(struct notifier_block *nb, unsigned long event,
 			     void *ptr)
 {
@@ -576,7 +601,7 @@
 	cbl->connected = event;
 	cbl->changed = true;
 
-	ci_irq(ci->irq, ci);
+	ci_irq(ci);
 	return NOTIFY_DONE;
 }
 
@@ -617,7 +642,7 @@
 	if (cable) {
 		cable->changed = true;
 		cable->connected = false;
-		ci_irq(ci->irq, ci);
+		ci_irq(ci);
 		spin_unlock_irqrestore(&ci->lock, flags);
 		if (ci->wq && role != USB_ROLE_NONE)
 			flush_workqueue(ci->wq);
@@ -635,7 +660,7 @@
 	if (cable) {
 		cable->changed = true;
 		cable->connected = true;
-		ci_irq(ci->irq, ci);
+		ci_irq(ci);
 	}
 	spin_unlock_irqrestore(&ci->lock, flags);
 	pm_runtime_put_sync(ci->dev);
@@ -700,13 +725,16 @@
 	if (usb_get_maximum_speed(dev) == USB_SPEED_FULL)
 		platdata->flags |= CI_HDRC_FORCE_FULLSPEED;
 
-	of_property_read_u32(dev->of_node, "phy-clkgate-delay-us",
-				     &platdata->phy_clkgate_delay_us);
+	if (of_property_read_u32(dev->of_node, "phy-clkgate-delay-us",
+				 &platdata->phy_clkgate_delay_us))
+		dev_dbg(dev, "Missing phy-clkgate-delay-us property\n");
 
 	platdata->itc_setting = 1;
 
-	of_property_read_u32(dev->of_node, "itc-setting",
-					&platdata->itc_setting);
+	if (of_property_read_u32(dev->of_node, "itc-setting",
+				 &platdata->itc_setting))
+		dev_dbg(dev, "Missing itc-setting property\n");
+
 
 	ret = of_property_read_u32(dev->of_node, "ahb-burst-config",
 				&platdata->ahb_burst_config);
@@ -965,9 +993,16 @@
 			     strlen(ci->roles[role]->name)))
 			break;
 
-	if (role == CI_ROLE_END || role == ci->role)
+	if (role == CI_ROLE_END)
 		return -EINVAL;
 
+	mutex_lock(&ci->mutex);
+
+	if (role == ci->role) {
+		mutex_unlock(&ci->mutex);
+		return n;
+	}
+
 	pm_runtime_get_sync(dev);
 	disable_irq(ci->irq);
 	ci_role_stop(ci);
@@ -976,6 +1011,7 @@
 		ci_handle_vbus_change(ci);
 	enable_irq(ci->irq);
 	pm_runtime_put_sync(dev);
+	mutex_unlock(&ci->mutex);
 
 	return (ret == 0) ? n : ret;
 }
@@ -1011,6 +1047,7 @@
 		return -ENOMEM;
 
 	spin_lock_init(&ci->lock);
+	mutex_init(&ci->mutex);
 	ci->dev = dev;
 	ci->platdata = dev_get_platdata(dev);
 	ci->imx28_write_fix = !!(ci->platdata->flags &
@@ -1080,7 +1117,7 @@
 	ret = ci_usb_phy_init(ci);
 	if (ret) {
 		dev_err(dev, "unable to init phy: %d\n", ret);
-		return ret;
+		goto ulpi_exit;
 	}
 
 	ci->hw_bank.phys = res->start;
@@ -1174,7 +1211,7 @@
 		}
 	}
 
-	ret = devm_request_irq(dev, ci->irq, ci_irq, IRQF_SHARED,
+	ret = devm_request_irq(dev, ci->irq, ci_irq_handler, IRQF_SHARED,
 			ci->platdata->name, ci);
 	if (ret)
 		goto stop;
@@ -1295,11 +1332,11 @@
 
 	if (!IS_ERR(cable_id->edev) && ci->is_otg &&
 		(otgsc & OTGSC_IDIE) && (otgsc & OTGSC_IDIS))
-		ci_irq(ci->irq, ci);
+		ci_irq(ci);
 
 	if (!IS_ERR(cable_vbus->edev) && ci->is_otg &&
 		(otgsc & OTGSC_BSVIE) && (otgsc & OTGSC_BSVIS))
-		ci_irq(ci->irq, ci);
+		ci_irq(ci);
 }
 
 static int ci_controller_resume(struct device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/debug.c
@@ -364,5 +364,5 @@
  */
 void dbg_remove_files(struct ci_hdrc *ci)
 {
-	debugfs_remove(debugfs_lookup(dev_name(ci->dev), usb_debug_root));
+	debugfs_lookup_and_remove(dev_name(ci->dev), usb_debug_root);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/host.c
@@ -30,8 +30,7 @@
 };
 
 struct ci_hdrc_dma_aligned_buffer {
-	void *kmalloc_ptr;
-	void *old_xfer_buffer;
+	void *original_buffer;
 	u8 data[];
 };
 
@@ -63,6 +62,14 @@
 		priv->enabled = enable;
 	}
 
+	if (ci->platdata->flags & CI_HDRC_PHY_VBUS_CONTROL &&
+			ci->usb_phy && ci->usb_phy->set_vbus) {
+		if (enable)
+			ci->usb_phy->set_vbus(ci->usb_phy, 1);
+		else
+			ci->usb_phy->set_vbus(ci->usb_phy, 0);
+	}
+
 	if (enable && (ci->platdata->phy_mode == USBPHY_INTERFACE_MODE_HSIC)) {
 		/*
 		 * Marvell 28nm HSIC PHY requires forcing the port to HS mode.
@@ -71,6 +78,7 @@
 		hw_port_test_set(ci, 5);
 		hw_port_test_set(ci, 0);
 	}
+
 	return 0;
 };
 
@@ -372,59 +380,52 @@
 	return 0;
 }
 
-static void ci_hdrc_free_dma_aligned_buffer(struct urb *urb)
+static void ci_hdrc_free_dma_aligned_buffer(struct urb *urb, bool copy_back)
 {
 	struct ci_hdrc_dma_aligned_buffer *temp;
-	size_t length;
 
 	if (!(urb->transfer_flags & URB_ALIGNED_TEMP_BUFFER))
 		return;
+	urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER;
 
 	temp = container_of(urb->transfer_buffer,
 			    struct ci_hdrc_dma_aligned_buffer, data);
+	urb->transfer_buffer = temp->original_buffer;
+
+	if (copy_back && usb_urb_dir_in(urb)) {
+		size_t length;
 
-	if (usb_urb_dir_in(urb)) {
 		if (usb_pipeisoc(urb->pipe))
 			length = urb->transfer_buffer_length;
 		else
 			length = urb->actual_length;
 
-		memcpy(temp->old_xfer_buffer, temp->data, length);
+		memcpy(temp->original_buffer, temp->data, length);
 	}
-	urb->transfer_buffer = temp->old_xfer_buffer;
-	kfree(temp->kmalloc_ptr);
 
-	urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER;
+	kfree(temp);
 }
 
 static int ci_hdrc_alloc_dma_aligned_buffer(struct urb *urb, gfp_t mem_flags)
 {
-	struct ci_hdrc_dma_aligned_buffer *temp, *kmalloc_ptr;
-	const unsigned int ci_hdrc_usb_dma_align = 32;
-	size_t kmalloc_size;
+	struct ci_hdrc_dma_aligned_buffer *temp;
 
-	if (urb->num_sgs || urb->sg || urb->transfer_buffer_length == 0 ||
-	    !((uintptr_t)urb->transfer_buffer & (ci_hdrc_usb_dma_align - 1)))
+	if (urb->num_sgs || urb->sg || urb->transfer_buffer_length == 0)
+		return 0;
+	if (IS_ALIGNED((uintptr_t)urb->transfer_buffer, 4)
+	    && IS_ALIGNED(urb->transfer_buffer_length, 4))
 		return 0;
 
-	/* Allocate a buffer with enough padding for alignment */
-	kmalloc_size = urb->transfer_buffer_length +
-		       sizeof(struct ci_hdrc_dma_aligned_buffer) +
-		       ci_hdrc_usb_dma_align - 1;
-
-	kmalloc_ptr = kmalloc(kmalloc_size, mem_flags);
-	if (!kmalloc_ptr)
+	temp = kmalloc(sizeof(*temp) + ALIGN(urb->transfer_buffer_length, 4), mem_flags);
+	if (!temp)
 		return -ENOMEM;
 
-	/* Position our struct dma_aligned_buffer such that data is aligned */
-	temp = PTR_ALIGN(kmalloc_ptr + 1, ci_hdrc_usb_dma_align) - 1;
-	temp->kmalloc_ptr = kmalloc_ptr;
-	temp->old_xfer_buffer = urb->transfer_buffer;
 	if (usb_urb_dir_out(urb))
 		memcpy(temp->data, urb->transfer_buffer,
 		       urb->transfer_buffer_length);
-	urb->transfer_buffer = temp->data;
 
+	temp->original_buffer = urb->transfer_buffer;
+	urb->transfer_buffer = temp->data;
 	urb->transfer_flags |= URB_ALIGNED_TEMP_BUFFER;
 
 	return 0;
@@ -441,7 +442,7 @@
 
 	ret = usb_hcd_map_urb_for_dma(hcd, urb, mem_flags);
 	if (ret)
-		ci_hdrc_free_dma_aligned_buffer(urb);
+		ci_hdrc_free_dma_aligned_buffer(urb, false);
 
 	return ret;
 }
@@ -449,7 +450,7 @@
 static void ci_hdrc_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb)
 {
 	usb_hcd_unmap_urb_for_dma(hcd, urb);
-	ci_hdrc_free_dma_aligned_buffer(urb);
+	ci_hdrc_free_dma_aligned_buffer(urb, true);
 }
 
 int ci_hdrc_host_init(struct ci_hdrc *ci)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/otg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/otg.c
@@ -167,8 +167,11 @@
 
 static void ci_handle_id_switch(struct ci_hdrc *ci)
 {
-	enum ci_role role = ci_otg_role(ci);
+	enum ci_role role;
+	int ret;
 
+	mutex_lock(&ci->mutex);
+	role = ci_otg_role(ci);
 	if (role != ci->role) {
 		dev_dbg(ci->dev, "switching from %s to %s\n",
 			ci_role(ci)->name, ci->roles[role]->name);
@@ -193,11 +196,15 @@
 			 */
 			hw_wait_vbus_lower_bsv(ci);
 
-		ci_role_start(ci, role);
+		ret = ci_role_start(ci, role);
+		if (ret < 0)
+			dev_dbg(ci->dev, "switching err %d\n", ret);
+
 		/* vbus change may have already occurred */
 		if (role == CI_ROLE_GADGET)
 			ci_handle_vbus_change(ci);
 	}
+	mutex_unlock(&ci->mutex);
 }
 /**
  * ci_otg_work - perform otg (vbus/id) event handle
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/otg_fsm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/otg_fsm.c
@@ -256,8 +256,10 @@
 	ci->enabled_otg_timer_bits &= ~(1 << t);
 	if (ci->next_otg_timer == t) {
 		if (ci->enabled_otg_timer_bits == 0) {
+			spin_unlock_irqrestore(&ci->lock, flags);
 			/* No enabled timers after delete it */
 			hrtimer_cancel(&ci->otg_fsm_hrtimer);
+			spin_lock_irqsave(&ci->lock, flags);
 			ci->next_otg_timer = NUM_OTG_FSM_TIMERS;
 		} else {
 			/* Find the next timer */
@@ -471,6 +473,11 @@
 				return;
 			}
 		}
+
+		if (ci->platdata->flags & CI_HDRC_PHY_VBUS_CONTROL &&
+				ci->usb_phy && ci->usb_phy->set_vbus)
+			ci->usb_phy->set_vbus(ci->usb_phy, 1);
+
 		/* Disable data pulse irq */
 		hw_write_otgsc(ci, OTGSC_DPIE, 0);
 
@@ -480,6 +487,10 @@
 		if (ci->platdata->reg_vbus)
 			regulator_disable(ci->platdata->reg_vbus);
 
+		if (ci->platdata->flags & CI_HDRC_PHY_VBUS_CONTROL &&
+				ci->usb_phy && ci->usb_phy->set_vbus)
+			ci->usb_phy->set_vbus(ci->usb_phy, 0);
+
 		fsm->a_bus_drop = 1;
 		fsm->a_bus_req = 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/udc.c
@@ -49,6 +49,8 @@
 	.wMaxPacketSize  = cpu_to_le16(CTRL_PAYLOAD_MAX),
 };
 
+static int reprime_dtd(struct ci_hdrc *ci, struct ci_hw_ep *hwep,
+		       struct td_node *node);
 /**
  * hw_ep_bit: calculates the bit number
  * @num: endpoint number
@@ -84,7 +86,7 @@
 		hw_write(ci, OP_ENDPTLISTADDR, ~0, dma);
 		/* interrupt, error, port change, reset, sleep/suspend */
 		hw_write(ci, OP_USBINTR, ~0,
-			     USBi_UI|USBi_UEI|USBi_PCI|USBi_URI|USBi_SLI);
+			     USBi_UI|USBi_UEI|USBi_PCI|USBi_URI);
 	} else {
 		hw_write(ci, OP_USBINTR, ~0, 0);
 	}
@@ -599,6 +601,12 @@
 
 		prevlastnode->ptr->next = cpu_to_le32(next);
 		wmb();
+
+		if (ci->rev == CI_REVISION_22) {
+			if (!hw_read(ci, OP_ENDPTSTAT, BIT(n)))
+				reprime_dtd(ci, hwep, prevlastnode);
+		}
+
 		if (hw_read(ci, OP_ENDPTPRIME, BIT(n)))
 			goto done;
 		do {
@@ -680,7 +688,8 @@
 		if ((TD_STATUS_ACTIVE & tmptoken) != 0) {
 			int n = hw_ep_bit(hwep->num, hwep->dir);
 
-			if (ci->rev == CI_REVISION_24)
+			if (ci->rev == CI_REVISION_24 ||
+			    ci->rev == CI_REVISION_22)
 				if (!hw_read(ci, OP_ENDPTSTAT, BIT(n)))
 					reprime_dtd(ci, hwep, node);
 			hwreq->req.status = -EALREADY;
@@ -868,6 +877,7 @@
 __acquires(ci->lock)
 {
 	int retval;
+	u32 intr;
 
 	spin_unlock(&ci->lock);
 	if (ci->gadget.speed != USB_SPEED_UNKNOWN)
@@ -881,6 +891,11 @@
 	if (retval)
 		goto done;
 
+	/* clear SLI */
+	hw_write(ci, OP_USBSTS, USBi_SLI, USBi_SLI);
+	intr = hw_read(ci, OP_USBINTR, ~0);
+	hw_write(ci, OP_USBINTR, ~0, intr | USBi_SLI);
+
 	ci->status = usb_ep_alloc_request(&ci->ep0in->ep, GFP_ATOMIC);
 	if (ci->status == NULL)
 		retval = -ENOMEM;
@@ -1040,6 +1055,9 @@
 	struct ci_hdrc *ci = req->context;
 	unsigned long flags;
 
+	if (req->status < 0)
+		return;
+
 	if (ci->setaddr) {
 		hw_usb_set_address(ci, ci->address);
 		ci->setaddr = false;
@@ -2021,7 +2039,7 @@
 			}
 		}
 
-		if (USBi_UI  & intr)
+		if ((USBi_UI | USBi_UEI) & intr)
 			isr_tr_complete_handler(ci);
 
 		if ((USBi_SLI & intr) && !(ci->suspended)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/chipidea/usbmisc_imx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/chipidea/usbmisc_imx.c
@@ -135,7 +135,7 @@
 #define TXVREFTUNE0_MASK		(0xf << 20)
 
 #define MX6_USB_OTG_WAKEUP_BITS (MX6_BM_WAKEUP_ENABLE | MX6_BM_VBUS_WAKEUP | \
-				 MX6_BM_ID_WAKEUP)
+				 MX6_BM_ID_WAKEUP | MX6SX_BM_DPDM_WAKEUP_EN)
 
 struct usbmisc_ops {
 	/* It's called once when probe a usb device */
@@ -657,13 +657,15 @@
 			usbmisc->base + MX7D_USBNC_USB_CTRL2);
 		/* PHY tuning for signal quality */
 		reg = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG1);
-		if (data->emp_curr_control && data->emp_curr_control <=
+		if (data->emp_curr_control >= 0 &&
+			data->emp_curr_control <=
 			(TXPREEMPAMPTUNE0_MASK >> TXPREEMPAMPTUNE0_BIT)) {
 			reg &= ~TXPREEMPAMPTUNE0_MASK;
 			reg |= (data->emp_curr_control << TXPREEMPAMPTUNE0_BIT);
 		}
 
-		if (data->dc_vol_level_adjust && data->dc_vol_level_adjust <=
+		if (data->dc_vol_level_adjust >= 0 &&
+			data->dc_vol_level_adjust <=
 			(TXVREFTUNE0_MASK >> TXVREFTUNE0_BIT)) {
 			reg &= ~TXVREFTUNE0_MASK;
 			reg |= (data->dc_vol_level_adjust << TXVREFTUNE0_BIT);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/class/cdc-acm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/class/cdc-acm.c
@@ -360,7 +360,7 @@
 static void acm_ctrl_irq(struct urb *urb)
 {
 	struct acm *acm = urb->context;
-	struct usb_cdc_notification *dr = urb->transfer_buffer;
+	struct usb_cdc_notification *dr;
 	unsigned int current_size = urb->actual_length;
 	unsigned int expected_size, copy_size, alloc_size;
 	int retval;
@@ -387,14 +387,25 @@
 
 	usb_mark_last_busy(acm->dev);
 
-	if (acm->nb_index)
+	if (acm->nb_index == 0) {
+		/*
+		 * The first chunk of a message must contain at least the
+		 * notification header with the length field, otherwise we
+		 * can't get an expected_size.
+		 */
+		if (current_size < sizeof(struct usb_cdc_notification)) {
+			dev_dbg(&acm->control->dev, "urb too short\n");
+			goto exit;
+		}
+		dr = urb->transfer_buffer;
+	} else {
 		dr = (struct usb_cdc_notification *)acm->notification_buffer;
-
+	}
 	/* size = notification-header + (optional) data */
 	expected_size = sizeof(struct usb_cdc_notification) +
 					le16_to_cpu(dr->wLength);
 
-	if (current_size < expected_size) {
+	if (acm->nb_index != 0 || current_size < expected_size) {
 		/* notification is transmitted fragmented, reassemble */
 		if (acm->nb_size < expected_size) {
 			u8 *new_buffer;
@@ -896,6 +907,9 @@
 	struct acm *acm = tty->driver_data;
 	int retval;
 
+	if (!(acm->ctrl_caps & USB_CDC_CAP_BRK))
+		return -EOPNOTSUPP;
+
 	retval = acm_send_break(acm, state ? 0xffff : 0);
 	if (retval < 0)
 		dev_dbg(&acm->control->dev,
@@ -939,10 +953,12 @@
 	struct acm *acm = tty->driver_data;
 
 	ss->line = acm->minor;
+	mutex_lock(&acm->port.mutex);
 	ss->close_delay	= jiffies_to_msecs(acm->port.close_delay) / 10;
 	ss->closing_wait = acm->port.closing_wait == ASYNC_CLOSING_WAIT_NONE ?
 				ASYNC_CLOSING_WAIT_NONE :
 				jiffies_to_msecs(acm->port.closing_wait) / 10;
+	mutex_unlock(&acm->port.mutex);
 	return 0;
 }
 
@@ -1702,13 +1718,16 @@
 	{ USB_DEVICE(0x0870, 0x0001), /* Metricom GS Modem */
 	.driver_info = NO_UNION_NORMAL, /* has no union descriptor */
 	},
-	{ USB_DEVICE(0x045b, 0x023c),	/* Renesas USB Download mode */
+	{ USB_DEVICE(0x045b, 0x023c),	/* Renesas R-Car H3 USB Download mode */
+	.driver_info = DISABLE_ECHO,	/* Don't echo banner */
+	},
+	{ USB_DEVICE(0x045b, 0x0247),	/* Renesas R-Car D3 USB Download mode */
 	.driver_info = DISABLE_ECHO,	/* Don't echo banner */
 	},
-	{ USB_DEVICE(0x045b, 0x0248),	/* Renesas USB Download mode */
+	{ USB_DEVICE(0x045b, 0x0248),	/* Renesas R-Car M3-N USB Download mode */
 	.driver_info = DISABLE_ECHO,	/* Don't echo banner */
 	},
-	{ USB_DEVICE(0x045b, 0x024D),	/* Renesas USB Download mode */
+	{ USB_DEVICE(0x045b, 0x024D),	/* Renesas R-Car E3 USB Download mode */
 	.driver_info = DISABLE_ECHO,	/* Don't echo banner */
 	},
 	{ USB_DEVICE(0x0e8d, 0x0003), /* FIREFLY, MediaTek Inc; andrey.arapov@gmail.com */
@@ -1738,6 +1757,9 @@
 	{ USB_DEVICE(0x11ca, 0x0201), /* VeriFone Mx870 Gadget Serial */
 	.driver_info = SINGLE_RX_URB,
 	},
+	{ USB_DEVICE(0x1901, 0x0006), /* GE Healthcare Patient Monitor UI Controller */
+	.driver_info = DISABLE_ECHO, /* DISABLE ECHO in termios flag */
+	},
 	{ USB_DEVICE(0x1965, 0x0018), /* Uniden UBC125XLT */
 	.driver_info = NO_UNION_NORMAL, /* has no union descriptor */
 	},
@@ -1814,6 +1836,9 @@
 	{ USB_DEVICE(0x09d8, 0x0320), /* Elatec GmbH TWN3 */
 	.driver_info = NO_UNION_NORMAL, /* has misplaced union descriptor */
 	},
+	{ USB_DEVICE(0x0c26, 0x0020), /* Icom ICF3400 Serie */
+	.driver_info = NO_UNION_NORMAL, /* reports zero length descriptor */
+	},
 	{ USB_DEVICE(0x0ca6, 0xa050), /* Castles VEGA3000 */
 	.driver_info = NO_UNION_NORMAL, /* reports zero length descriptor */
 	},
@@ -1962,6 +1987,20 @@
 	.driver_info = IGNORE_DEVICE,
 	},
 
+	/* Exclude Exar USB serial ports */
+	{ USB_DEVICE(0x04e2, 0x1400), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1401), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1402), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1403), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1410), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1411), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1412), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1414), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1420), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1421), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1422), .driver_info = IGNORE_DEVICE, },
+	{ USB_DEVICE(0x04e2, 0x1424), .driver_info = IGNORE_DEVICE, },
+
 	/* control interfaces without any protocol set */
 	{ USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_ACM,
 		USB_CDC_PROTO_NONE) },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/class/cdc-wdm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/class/cdc-wdm.c
@@ -266,14 +266,14 @@
 			dev_err(&desc->intf->dev, "Stall on int endpoint\n");
 			goto sw; /* halt is cleared in work */
 		default:
-			dev_err(&desc->intf->dev,
+			dev_err_ratelimited(&desc->intf->dev,
 				"nonzero urb status received: %d\n", status);
 			break;
 		}
 	}
 
 	if (urb->actual_length < sizeof(struct usb_cdc_notification)) {
-		dev_err(&desc->intf->dev, "wdm_int_callback - %d bytes\n",
+		dev_err_ratelimited(&desc->intf->dev, "wdm_int_callback - %d bytes\n",
 			urb->actual_length);
 		goto exit;
 	}
@@ -774,6 +774,7 @@
 			poison_urbs(desc);
 			spin_lock_irq(&desc->iuspin);
 			desc->resp_count = 0;
+			clear_bit(WDM_RESPONDING, &desc->flags);
 			spin_unlock_irq(&desc->iuspin);
 			desc->manage_power(desc->intf, 0);
 			unpoison_urbs(desc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/class/usblp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/class/usblp.c
@@ -1337,11 +1337,12 @@
 	if (protocol < USBLP_FIRST_PROTOCOL || protocol > USBLP_LAST_PROTOCOL)
 		return -EINVAL;
 
+	alts = usblp->protocol[protocol].alt_setting;
+	if (alts < 0)
+		return -EINVAL;
+
 	/* Don't unnecessarily set the interface if there's a single alt. */
 	if (usblp->intf->num_altsetting > 1) {
-		alts = usblp->protocol[protocol].alt_setting;
-		if (alts < 0)
-			return -EINVAL;
 		r = usb_set_interface(usblp->dev, usblp->ifnum, alts);
 		if (r < 0) {
 			printk(KERN_ERR "usblp: can't set desired altsetting %d on interface %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/class/usbtmc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/class/usbtmc.c
@@ -754,7 +754,7 @@
 	if (!urb)
 		return NULL;
 
-	dmabuf = kmalloc(bufsize, GFP_KERNEL);
+	dmabuf = kzalloc(bufsize, GFP_KERNEL);
 	if (!dmabuf) {
 		usb_free_urb(urb);
 		return NULL;
@@ -1919,6 +1919,7 @@
 	struct usbtmc_ctrlrequest request;
 	u8 *buffer = NULL;
 	int rv;
+	unsigned int is_in, pipe;
 	unsigned long res;
 
 	res = copy_from_user(&request, arg, sizeof(struct usbtmc_ctrlrequest));
@@ -1927,13 +1928,17 @@
 
 	if (request.req.wLength > USBTMC_BUFSIZE)
 		return -EMSGSIZE;
+	if (request.req.wLength == 0)	/* Length-0 requests are never IN */
+		request.req.bRequestType &= ~USB_DIR_IN;
+
+	is_in = request.req.bRequestType & USB_DIR_IN;
 
 	if (request.req.wLength) {
 		buffer = kmalloc(request.req.wLength, GFP_KERNEL);
 		if (!buffer)
 			return -ENOMEM;
 
-		if ((request.req.bRequestType & USB_DIR_IN) == 0) {
+		if (!is_in) {
 			/* Send control data to device */
 			res = copy_from_user(buffer, request.data,
 					     request.req.wLength);
@@ -1944,8 +1949,12 @@
 		}
 	}
 
+	if (is_in)
+		pipe = usb_rcvctrlpipe(data->usb_dev, 0);
+	else
+		pipe = usb_sndctrlpipe(data->usb_dev, 0);
 	rv = usb_control_msg(data->usb_dev,
-			usb_rcvctrlpipe(data->usb_dev, 0),
+			pipe,
 			request.req.bRequest,
 			request.req.bRequestType,
 			request.req.wValue,
@@ -1957,7 +1966,7 @@
 		goto exit;
 	}
 
-	if (rv && (request.req.bRequestType & USB_DIR_IN)) {
+	if (rv && is_in) {
 		/* Read control data from device */
 		res = copy_to_user(request.data, buffer, rv);
 		if (res)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/common/debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/common/debug.c
@@ -207,30 +207,28 @@
 	snprintf(str, size, "Set Isochronous Delay(Delay = %d ns)", wValue);
 }
 
-/**
- * usb_decode_ctrl - Returns human readable representation of control request.
- * @str: buffer to return a human-readable representation of control request.
- *       This buffer should have about 200 bytes.
- * @size: size of str buffer.
- * @bRequestType: matches the USB bmRequestType field
- * @bRequest: matches the USB bRequest field
- * @wValue: matches the USB wValue field (CPU byte order)
- * @wIndex: matches the USB wIndex field (CPU byte order)
- * @wLength: matches the USB wLength field (CPU byte order)
- *
- * Function returns decoded, formatted and human-readable description of
- * control request packet.
- *
- * The usage scenario for this is for tracepoints, so function as a return
- * use the same value as in parameters. This approach allows to use this
- * function in TP_printk
- *
- * Important: wValue, wIndex, wLength parameters before invoking this function
- * should be processed by le16_to_cpu macro.
- */
-const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
-			    __u8 bRequest, __u16 wValue, __u16 wIndex,
-			    __u16 wLength)
+static void usb_decode_ctrl_generic(char *str, size_t size, __u8 bRequestType,
+				    __u8 bRequest, __u16 wValue, __u16 wIndex,
+				    __u16 wLength)
+{
+	u8 recip = bRequestType & USB_RECIP_MASK;
+	u8 type = bRequestType & USB_TYPE_MASK;
+
+	snprintf(str, size,
+		 "Type=%s Recipient=%s Dir=%s bRequest=%u wValue=%u wIndex=%u wLength=%u",
+		 (type == USB_TYPE_STANDARD)    ? "Standard" :
+		 (type == USB_TYPE_VENDOR)      ? "Vendor" :
+		 (type == USB_TYPE_CLASS)       ? "Class" : "Unknown",
+		 (recip == USB_RECIP_DEVICE)    ? "Device" :
+		 (recip == USB_RECIP_INTERFACE) ? "Interface" :
+		 (recip == USB_RECIP_ENDPOINT)  ? "Endpoint" : "Unknown",
+		 (bRequestType & USB_DIR_IN)    ? "IN" : "OUT",
+		 bRequest, wValue, wIndex, wLength);
+}
+
+static void usb_decode_ctrl_standard(char *str, size_t size, __u8 bRequestType,
+				     __u8 bRequest, __u16 wValue, __u16 wIndex,
+				     __u16 wLength)
 {
 	switch (bRequest) {
 	case USB_REQ_GET_STATUS:
@@ -271,14 +269,48 @@
 		usb_decode_set_isoch_delay(wValue, str, size);
 		break;
 	default:
-		snprintf(str, size, "%02x %02x %02x %02x %02x %02x %02x %02x",
-			 bRequestType, bRequest,
-			 (u8)(cpu_to_le16(wValue) & 0xff),
-			 (u8)(cpu_to_le16(wValue) >> 8),
-			 (u8)(cpu_to_le16(wIndex) & 0xff),
-			 (u8)(cpu_to_le16(wIndex) >> 8),
-			 (u8)(cpu_to_le16(wLength) & 0xff),
-			 (u8)(cpu_to_le16(wLength) >> 8));
+		usb_decode_ctrl_generic(str, size, bRequestType, bRequest,
+					wValue, wIndex, wLength);
+		break;
+	}
+}
+
+/**
+ * usb_decode_ctrl - Returns human readable representation of control request.
+ * @str: buffer to return a human-readable representation of control request.
+ *       This buffer should have about 200 bytes.
+ * @size: size of str buffer.
+ * @bRequestType: matches the USB bmRequestType field
+ * @bRequest: matches the USB bRequest field
+ * @wValue: matches the USB wValue field (CPU byte order)
+ * @wIndex: matches the USB wIndex field (CPU byte order)
+ * @wLength: matches the USB wLength field (CPU byte order)
+ *
+ * Function returns decoded, formatted and human-readable description of
+ * control request packet.
+ *
+ * The usage scenario for this is for tracepoints, so function as a return
+ * use the same value as in parameters. This approach allows to use this
+ * function in TP_printk
+ *
+ * Important: wValue, wIndex, wLength parameters before invoking this function
+ * should be processed by le16_to_cpu macro.
+ */
+const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
+			    __u8 bRequest, __u16 wValue, __u16 wIndex,
+			    __u16 wLength)
+{
+	switch (bRequestType & USB_TYPE_MASK) {
+	case USB_TYPE_STANDARD:
+		usb_decode_ctrl_standard(str, size, bRequestType, bRequest,
+					 wValue, wIndex, wLength);
+		break;
+	case USB_TYPE_VENDOR:
+	case USB_TYPE_CLASS:
+	default:
+		usb_decode_ctrl_generic(str, size, bRequestType, bRequest,
+					wValue, wIndex, wLength);
+		break;
 	}
 
 	return str;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/common/ulpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/common/ulpi.c
@@ -39,8 +39,11 @@
 	struct ulpi *ulpi = to_ulpi_dev(dev);
 	const struct ulpi_device_id *id;
 
-	/* Some ULPI devices don't have a vendor id so rely on OF match */
-	if (ulpi->id.vendor == 0)
+	/*
+	 * Some ULPI devices don't have a vendor id
+	 * or provide an id_table so rely on OF match.
+	 */
+	if (ulpi->id.vendor == 0 || !drv->id_table)
 		return of_driver_match_device(dev, driver);
 
 	for (id = drv->id_table; id->vendor; id++)
@@ -127,6 +130,7 @@
 
 static void ulpi_dev_release(struct device *dev)
 {
+	of_node_put(dev->of_node);
 	kfree(to_ulpi_dev(dev));
 }
 
@@ -244,12 +248,16 @@
 		return ret;
 
 	ret = ulpi_read_id(ulpi);
-	if (ret)
+	if (ret) {
+		of_node_put(ulpi->dev.of_node);
 		return ret;
+	}
 
 	ret = device_register(&ulpi->dev);
-	if (ret)
+	if (ret) {
+		put_device(&ulpi->dev);
 		return ret;
+	}
 
 	dev_dbg(&ulpi->dev, "registered ULPI PHY: vendor %04x, product %04x\n",
 		ulpi->id.vendor, ulpi->id.product);
@@ -296,7 +304,6 @@
  */
 void ulpi_unregister_interface(struct ulpi *ulpi)
 {
-	of_node_put(ulpi->dev.of_node);
 	device_unregister(&ulpi->dev);
 }
 EXPORT_SYMBOL_GPL(ulpi_unregister_interface);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/common/usb-conn-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/common/usb-conn-gpio.c
@@ -42,6 +42,7 @@
 
 	struct power_supply_desc desc;
 	struct power_supply *charger;
+	bool initial_detection;
 };
 
 /*
@@ -86,11 +87,13 @@
 	dev_dbg(info->dev, "role %s -> %s, gpios: id %d, vbus %d\n",
 		usb_role_string(info->last_role), usb_role_string(role), id, vbus);
 
-	if (info->last_role == role) {
+	if (!info->initial_detection && info->last_role == role) {
 		dev_warn(info->dev, "repeated role: %s\n", usb_role_string(role));
 		return;
 	}
 
+	info->initial_detection = false;
+
 	if (info->last_role == USB_ROLE_HOST && info->vbus)
 		regulator_disable(info->vbus);
 
@@ -273,6 +276,7 @@
 	platform_set_drvdata(pdev, info);
 
 	/* Perform initial detection */
+	info->initial_detection = true;
 	usb_conn_queue_dwork(info, 0);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/buffer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/buffer.c
@@ -172,3 +172,44 @@
 	}
 	dma_free_coherent(hcd->self.sysdev, size, addr, dma);
 }
+
+void *hcd_buffer_alloc_pages(struct usb_hcd *hcd,
+		size_t size, gfp_t mem_flags, dma_addr_t *dma)
+{
+	if (size == 0)
+		return NULL;
+
+	if (hcd->localmem_pool)
+		return gen_pool_dma_alloc_align(hcd->localmem_pool,
+				size, dma, PAGE_SIZE);
+
+	/* some USB hosts just use PIO */
+	if (!hcd_uses_dma(hcd)) {
+		*dma = DMA_MAPPING_ERROR;
+		return (void *)__get_free_pages(mem_flags,
+				get_order(size));
+	}
+
+	return dma_alloc_coherent(hcd->self.sysdev,
+			size, dma, mem_flags);
+}
+
+void hcd_buffer_free_pages(struct usb_hcd *hcd,
+		size_t size, void *addr, dma_addr_t dma)
+{
+	if (!addr)
+		return;
+
+	if (hcd->localmem_pool) {
+		gen_pool_free(hcd->localmem_pool,
+				(unsigned long)addr, size);
+		return;
+	}
+
+	if (!hcd_uses_dma(hcd)) {
+		free_pages((unsigned long)addr, get_order(size));
+		return;
+	}
+
+	dma_free_coherent(hcd->self.sysdev, size, addr, dma);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/config.c
@@ -61,7 +61,7 @@
 	desc = (struct usb_ssp_isoc_ep_comp_descriptor *) buffer;
 	if (desc->bDescriptorType != USB_DT_SSP_ISOC_ENDPOINT_COMP ||
 	    size < USB_DT_SSP_ISOC_EP_COMP_SIZE) {
-		dev_warn(ddev, "Invalid SuperSpeedPlus isoc endpoint companion"
+		dev_notice(ddev, "Invalid SuperSpeedPlus isoc endpoint companion"
 			 "for config %d interface %d altsetting %d ep %d.\n",
 			 cfgno, inum, asnum, ep->desc.bEndpointAddress);
 		return;
@@ -83,7 +83,7 @@
 
 	if (desc->bDescriptorType != USB_DT_SS_ENDPOINT_COMP ||
 			size < USB_DT_SS_EP_COMP_SIZE) {
-		dev_warn(ddev, "No SuperSpeed endpoint companion for config %d "
+		dev_notice(ddev, "No SuperSpeed endpoint companion for config %d "
 				" interface %d altsetting %d ep %d: "
 				"using minimum values\n",
 				cfgno, inum, asnum, ep->desc.bEndpointAddress);
@@ -109,13 +109,13 @@
 
 	/* Check the various values */
 	if (usb_endpoint_xfer_control(&ep->desc) && desc->bMaxBurst != 0) {
-		dev_warn(ddev, "Control endpoint with bMaxBurst = %d in "
+		dev_notice(ddev, "Control endpoint with bMaxBurst = %d in "
 				"config %d interface %d altsetting %d ep %d: "
 				"setting to zero\n", desc->bMaxBurst,
 				cfgno, inum, asnum, ep->desc.bEndpointAddress);
 		ep->ss_ep_comp.bMaxBurst = 0;
 	} else if (desc->bMaxBurst > 15) {
-		dev_warn(ddev, "Endpoint with bMaxBurst = %d in "
+		dev_notice(ddev, "Endpoint with bMaxBurst = %d in "
 				"config %d interface %d altsetting %d ep %d: "
 				"setting to 15\n", desc->bMaxBurst,
 				cfgno, inum, asnum, ep->desc.bEndpointAddress);
@@ -125,7 +125,7 @@
 	if ((usb_endpoint_xfer_control(&ep->desc) ||
 			usb_endpoint_xfer_int(&ep->desc)) &&
 				desc->bmAttributes != 0) {
-		dev_warn(ddev, "%s endpoint with bmAttributes = %d in "
+		dev_notice(ddev, "%s endpoint with bmAttributes = %d in "
 				"config %d interface %d altsetting %d ep %d: "
 				"setting to zero\n",
 				usb_endpoint_xfer_control(&ep->desc) ? "Control" : "Bulk",
@@ -134,7 +134,7 @@
 		ep->ss_ep_comp.bmAttributes = 0;
 	} else if (usb_endpoint_xfer_bulk(&ep->desc) &&
 			desc->bmAttributes > 16) {
-		dev_warn(ddev, "Bulk endpoint with more than 65536 streams in "
+		dev_notice(ddev, "Bulk endpoint with more than 65536 streams in "
 				"config %d interface %d altsetting %d ep %d: "
 				"setting to max\n",
 				cfgno, inum, asnum, ep->desc.bEndpointAddress);
@@ -142,7 +142,7 @@
 	} else if (usb_endpoint_xfer_isoc(&ep->desc) &&
 		   !USB_SS_SSP_ISOC_COMP(desc->bmAttributes) &&
 		   USB_SS_MULT(desc->bmAttributes) > 3) {
-		dev_warn(ddev, "Isoc endpoint has Mult of %d in "
+		dev_notice(ddev, "Isoc endpoint has Mult of %d in "
 				"config %d interface %d altsetting %d ep %d: "
 				"setting to 3\n",
 				USB_SS_MULT(desc->bmAttributes),
@@ -160,7 +160,7 @@
 	else
 		max_tx = 999999;
 	if (le16_to_cpu(desc->wBytesPerInterval) > max_tx) {
-		dev_warn(ddev, "%s endpoint with wBytesPerInterval of %d in "
+		dev_notice(ddev, "%s endpoint with wBytesPerInterval of %d in "
 				"config %d interface %d altsetting %d ep %d: "
 				"setting to %d\n",
 				usb_endpoint_xfer_isoc(&ep->desc) ? "Isoc" : "Int",
@@ -273,7 +273,7 @@
 	else if (d->bLength >= USB_DT_ENDPOINT_SIZE)
 		n = USB_DT_ENDPOINT_SIZE;
 	else {
-		dev_warn(ddev, "config %d interface %d altsetting %d has an "
+		dev_notice(ddev, "config %d interface %d altsetting %d has an "
 		    "invalid endpoint descriptor of length %d, skipping\n",
 		    cfgno, inum, asnum, d->bLength);
 		goto skip_to_next_endpoint_or_interface_descriptor;
@@ -281,7 +281,7 @@
 
 	i = d->bEndpointAddress & ~USB_ENDPOINT_DIR_MASK;
 	if (i >= 16 || i == 0) {
-		dev_warn(ddev, "config %d interface %d altsetting %d has an "
+		dev_notice(ddev, "config %d interface %d altsetting %d has an "
 		    "invalid endpoint with address 0x%X, skipping\n",
 		    cfgno, inum, asnum, d->bEndpointAddress);
 		goto skip_to_next_endpoint_or_interface_descriptor;
@@ -291,9 +291,23 @@
 	if (ifp->desc.bNumEndpoints >= num_ep)
 		goto skip_to_next_endpoint_or_interface_descriptor;
 
+	/* Save a copy of the descriptor and use it instead of the original */
+	endpoint = &ifp->endpoint[ifp->desc.bNumEndpoints];
+	memcpy(&endpoint->desc, d, n);
+	d = &endpoint->desc;
+
+	/* Clear the reserved bits in bEndpointAddress */
+	i = d->bEndpointAddress &
+			(USB_ENDPOINT_DIR_MASK | USB_ENDPOINT_NUMBER_MASK);
+	if (i != d->bEndpointAddress) {
+		dev_notice(ddev, "config %d interface %d altsetting %d has an endpoint descriptor with address 0x%X, changing to 0x%X\n",
+		    cfgno, inum, asnum, d->bEndpointAddress, i);
+		endpoint->desc.bEndpointAddress = i;
+	}
+
 	/* Check for duplicate endpoint addresses */
 	if (config_endpoint_is_duplicate(config, inum, asnum, d)) {
-		dev_warn(ddev, "config %d interface %d altsetting %d has a duplicate endpoint with address 0x%X, skipping\n",
+		dev_notice(ddev, "config %d interface %d altsetting %d has a duplicate endpoint with address 0x%X, skipping\n",
 				cfgno, inum, asnum, d->bEndpointAddress);
 		goto skip_to_next_endpoint_or_interface_descriptor;
 	}
@@ -301,17 +315,15 @@
 	/* Ignore some endpoints */
 	if (udev->quirks & USB_QUIRK_ENDPOINT_IGNORE) {
 		if (usb_endpoint_is_ignored(udev, ifp, d)) {
-			dev_warn(ddev, "config %d interface %d altsetting %d has an ignored endpoint with address 0x%X, skipping\n",
+			dev_notice(ddev, "config %d interface %d altsetting %d has an ignored endpoint with address 0x%X, skipping\n",
 					cfgno, inum, asnum,
 					d->bEndpointAddress);
 			goto skip_to_next_endpoint_or_interface_descriptor;
 		}
 	}
 
-	endpoint = &ifp->endpoint[ifp->desc.bNumEndpoints];
+	/* Accept this endpoint */
 	++ifp->desc.bNumEndpoints;
-
-	memcpy(&endpoint->desc, d, n);
 	INIT_LIST_HEAD(&endpoint->urb_list);
 
 	/*
@@ -378,7 +390,7 @@
 		}
 	}
 	if (d->bInterval < i || d->bInterval > j) {
-		dev_warn(ddev, "config %d interface %d altsetting %d "
+		dev_notice(ddev, "config %d interface %d altsetting %d "
 		    "endpoint 0x%X has an invalid bInterval %d, "
 		    "changing to %d\n",
 		    cfgno, inum, asnum,
@@ -391,7 +403,7 @@
 	 * them usable, we will try treating them as Interrupt endpoints.
 	 */
 	if (udev->speed == USB_SPEED_LOW && usb_endpoint_xfer_bulk(d)) {
-		dev_warn(ddev, "config %d interface %d altsetting %d "
+		dev_notice(ddev, "config %d interface %d altsetting %d "
 		    "endpoint 0x%X is Bulk; changing to Interrupt\n",
 		    cfgno, inum, asnum, d->bEndpointAddress);
 		endpoint->desc.bmAttributes = USB_ENDPOINT_XFER_INT;
@@ -406,9 +418,9 @@
 	 * the USB-2 spec requires such endpoints to have wMaxPacketSize = 0
 	 * (see the end of section 5.6.3), so don't warn about them.
 	 */
-	maxp = usb_endpoint_maxp(&endpoint->desc);
+	maxp = le16_to_cpu(endpoint->desc.wMaxPacketSize);
 	if (maxp == 0 && !(usb_endpoint_xfer_isoc(d) && asnum == 0)) {
-		dev_warn(ddev, "config %d interface %d altsetting %d endpoint 0x%X has invalid wMaxPacketSize 0\n",
+		dev_notice(ddev, "config %d interface %d altsetting %d endpoint 0x%X has invalid wMaxPacketSize 0\n",
 		    cfgno, inum, asnum, d->bEndpointAddress);
 	}
 
@@ -422,9 +434,9 @@
 		maxpacket_maxes = full_speed_maxpacket_maxes;
 		break;
 	case USB_SPEED_HIGH:
-		/* Bits 12..11 are allowed only for HS periodic endpoints */
+		/* Multiple-transactions bits are allowed only for HS periodic endpoints */
 		if (usb_endpoint_xfer_int(d) || usb_endpoint_xfer_isoc(d)) {
-			i = maxp & (BIT(12) | BIT(11));
+			i = maxp & USB_EP_MAXP_MULT_MASK;
 			maxp &= ~i;
 		}
 		fallthrough;
@@ -439,7 +451,7 @@
 	j = maxpacket_maxes[usb_endpoint_type(&endpoint->desc)];
 
 	if (maxp > j) {
-		dev_warn(ddev, "config %d interface %d altsetting %d endpoint 0x%X has invalid maxpacket %d, setting to %d\n",
+		dev_notice(ddev, "config %d interface %d altsetting %d endpoint 0x%X has invalid maxpacket %d, setting to %d\n",
 		    cfgno, inum, asnum, d->bEndpointAddress, maxp, j);
 		maxp = j;
 		endpoint->desc.wMaxPacketSize = cpu_to_le16(i | maxp);
@@ -452,7 +464,7 @@
 	 */
 	if (udev->speed == USB_SPEED_HIGH && usb_endpoint_xfer_bulk(d)) {
 		if (maxp != 512)
-			dev_warn(ddev, "config %d interface %d altsetting %d "
+			dev_notice(ddev, "config %d interface %d altsetting %d "
 				"bulk endpoint 0x%X has invalid maxpacket %d\n",
 				cfgno, inum, asnum, d->bEndpointAddress,
 				maxp);
@@ -533,7 +545,7 @@
 	      i < intfc->num_altsetting;
 	     (++i, ++alt)) {
 		if (alt->desc.bAlternateSetting == asnum) {
-			dev_warn(ddev, "Duplicate descriptor for config %d "
+			dev_notice(ddev, "Duplicate descriptor for config %d "
 			    "interface %d altsetting %d, skipping\n",
 			    cfgno, inum, asnum);
 			goto skip_to_next_interface_descriptor;
@@ -559,7 +571,7 @@
 	num_ep = num_ep_orig = alt->desc.bNumEndpoints;
 	alt->desc.bNumEndpoints = 0;		/* Use as a counter */
 	if (num_ep > USB_MAXENDPOINTS) {
-		dev_warn(ddev, "too many endpoints for config %d interface %d "
+		dev_notice(ddev, "too many endpoints for config %d interface %d "
 		    "altsetting %d: %d, using maximum allowed: %d\n",
 		    cfgno, inum, asnum, num_ep, USB_MAXENDPOINTS);
 		num_ep = USB_MAXENDPOINTS;
@@ -590,7 +602,7 @@
 	}
 
 	if (n != num_ep_orig)
-		dev_warn(ddev, "config %d interface %d altsetting %d has %d "
+		dev_notice(ddev, "config %d interface %d altsetting %d has %d "
 		    "endpoint descriptor%s, different from the interface "
 		    "descriptor's value: %d\n",
 		    cfgno, inum, asnum, n, plural(n), num_ep_orig);
@@ -625,7 +637,7 @@
 	if (config->desc.bDescriptorType != USB_DT_CONFIG ||
 	    config->desc.bLength < USB_DT_CONFIG_SIZE ||
 	    config->desc.bLength > size) {
-		dev_err(ddev, "invalid descriptor for config index %d: "
+		dev_notice(ddev, "invalid descriptor for config index %d: "
 		    "type = 0x%X, length = %d\n", cfgidx,
 		    config->desc.bDescriptorType, config->desc.bLength);
 		return -EINVAL;
@@ -636,7 +648,7 @@
 	size -= config->desc.bLength;
 
 	if (nintf > USB_MAXINTERFACES) {
-		dev_warn(ddev, "config %d has too many interfaces: %d, "
+		dev_notice(ddev, "config %d has too many interfaces: %d, "
 		    "using maximum allowed: %d\n",
 		    cfgno, nintf, USB_MAXINTERFACES);
 		nintf = USB_MAXINTERFACES;
@@ -650,7 +662,7 @@
 	     (buffer2 += header->bLength, size2 -= header->bLength)) {
 
 		if (size2 < sizeof(struct usb_descriptor_header)) {
-			dev_warn(ddev, "config %d descriptor has %d excess "
+			dev_notice(ddev, "config %d descriptor has %d excess "
 			    "byte%s, ignoring\n",
 			    cfgno, size2, plural(size2));
 			break;
@@ -658,7 +670,7 @@
 
 		header = (struct usb_descriptor_header *) buffer2;
 		if ((header->bLength > size2) || (header->bLength < 2)) {
-			dev_warn(ddev, "config %d has an invalid descriptor "
+			dev_notice(ddev, "config %d has an invalid descriptor "
 			    "of length %d, skipping remainder of the config\n",
 			    cfgno, header->bLength);
 			break;
@@ -670,7 +682,7 @@
 
 			d = (struct usb_interface_descriptor *) header;
 			if (d->bLength < USB_DT_INTERFACE_SIZE) {
-				dev_warn(ddev, "config %d has an invalid "
+				dev_notice(ddev, "config %d has an invalid "
 				    "interface descriptor of length %d, "
 				    "skipping\n", cfgno, d->bLength);
 				continue;
@@ -680,7 +692,7 @@
 
 			if ((dev->quirks & USB_QUIRK_HONOR_BNUMINTERFACES) &&
 			    n >= nintf_orig) {
-				dev_warn(ddev, "config %d has more interface "
+				dev_notice(ddev, "config %d has more interface "
 				    "descriptors, than it declares in "
 				    "bNumInterfaces, ignoring interface "
 				    "number: %d\n", cfgno, inum);
@@ -688,7 +700,7 @@
 			}
 
 			if (inum >= nintf_orig)
-				dev_warn(ddev, "config %d has an invalid "
+				dev_notice(ddev, "config %d has an invalid "
 				    "interface number: %d but max is %d\n",
 				    cfgno, inum, nintf_orig - 1);
 
@@ -713,14 +725,14 @@
 
 			d = (struct usb_interface_assoc_descriptor *)header;
 			if (d->bLength < USB_DT_INTERFACE_ASSOCIATION_SIZE) {
-				dev_warn(ddev,
+				dev_notice(ddev,
 					 "config %d has an invalid interface association descriptor of length %d, skipping\n",
 					 cfgno, d->bLength);
 				continue;
 			}
 
 			if (iad_num == USB_MAXIADS) {
-				dev_warn(ddev, "found more Interface "
+				dev_notice(ddev, "found more Interface "
 					       "Association Descriptors "
 					       "than allocated for in "
 					       "configuration %d\n", cfgno);
@@ -731,7 +743,7 @@
 
 		} else if (header->bDescriptorType == USB_DT_DEVICE ||
 			    header->bDescriptorType == USB_DT_CONFIG)
-			dev_warn(ddev, "config %d contains an unexpected "
+			dev_notice(ddev, "config %d contains an unexpected "
 			    "descriptor of type 0x%X, skipping\n",
 			    cfgno, header->bDescriptorType);
 
@@ -740,11 +752,11 @@
 	config->desc.wTotalLength = cpu_to_le16(buffer2 - buffer0);
 
 	if (n != nintf)
-		dev_warn(ddev, "config %d has %d interface%s, different from "
+		dev_notice(ddev, "config %d has %d interface%s, different from "
 		    "the descriptor's value: %d\n",
 		    cfgno, n, plural(n), nintf_orig);
 	else if (n == 0)
-		dev_warn(ddev, "config %d has no interfaces?\n", cfgno);
+		dev_notice(ddev, "config %d has no interfaces?\n", cfgno);
 	config->desc.bNumInterfaces = nintf = n;
 
 	/* Check for missing interface numbers */
@@ -754,7 +766,7 @@
 				break;
 		}
 		if (j >= nintf)
-			dev_warn(ddev, "config %d has no interface number "
+			dev_notice(ddev, "config %d has no interface number "
 			    "%d\n", cfgno, i);
 	}
 
@@ -762,7 +774,7 @@
 	for (i = 0; i < nintf; ++i) {
 		j = nalts[i];
 		if (j > USB_MAXALTSETTING) {
-			dev_warn(ddev, "too many alternate settings for "
+			dev_notice(ddev, "too many alternate settings for "
 			    "config %d interface %d: %d, "
 			    "using maximum allowed: %d\n",
 			    cfgno, inums[i], j, USB_MAXALTSETTING);
@@ -811,7 +823,7 @@
 					break;
 			}
 			if (n >= intfc->num_altsetting)
-				dev_warn(ddev, "config %d interface %d has no "
+				dev_notice(ddev, "config %d interface %d has no "
 				    "altsetting %d\n", cfgno, inums[i], j);
 		}
 	}
@@ -868,7 +880,7 @@
 	int result;
 
 	if (ncfg > USB_MAXCONFIG) {
-		dev_warn(ddev, "too many configurations: %d, "
+		dev_notice(ddev, "too many configurations: %d, "
 		    "using maximum allowed: %d\n", ncfg, USB_MAXCONFIG);
 		dev->descriptor.bNumConfigurations = ncfg = USB_MAXCONFIG;
 	}
@@ -902,7 +914,7 @@
 			    "descriptor/%s: %d\n", cfgno, "start", result);
 			if (result != -EPIPE)
 				goto err;
-			dev_err(ddev, "chopping to %d config(s)\n", cfgno);
+			dev_notice(ddev, "chopping to %d config(s)\n", cfgno);
 			dev->descriptor.bNumConfigurations = cfgno;
 			break;
 		} else if (result < 4) {
@@ -934,7 +946,7 @@
 			goto err;
 		}
 		if (result < length) {
-			dev_warn(ddev, "config index %d descriptor too short "
+			dev_notice(ddev, "config index %d descriptor too short "
 			    "(expected %i, got %i)\n", cfgno, length, result);
 			length = result;
 		}
@@ -993,7 +1005,7 @@
 	/* Get BOS descriptor */
 	ret = usb_get_descriptor(dev, USB_DT_BOS, 0, bos, USB_DT_BOS_SIZE);
 	if (ret < USB_DT_BOS_SIZE || bos->bLength < USB_DT_BOS_SIZE) {
-		dev_err(ddev, "unable to get BOS descriptor or descriptor too short\n");
+		dev_notice(ddev, "unable to get BOS descriptor or descriptor too short\n");
 		if (ret >= 0)
 			ret = -ENOMSG;
 		kfree(bos);
@@ -1021,7 +1033,7 @@
 
 	ret = usb_get_descriptor(dev, USB_DT_BOS, 0, buffer, total_len);
 	if (ret < total_len) {
-		dev_err(ddev, "unable to get BOS descriptor set\n");
+		dev_notice(ddev, "unable to get BOS descriptor set\n");
 		if (ret >= 0)
 			ret = -ENOMSG;
 		goto err;
@@ -1046,8 +1058,8 @@
 		}
 
 		if (cap->bDescriptorType != USB_DT_DEVICE_CAPABILITY) {
-			dev_warn(ddev, "descriptor type invalid, skip\n");
-			continue;
+			dev_notice(ddev, "descriptor type invalid, skip\n");
+			goto skip_to_next_descriptor;
 		}
 
 		switch (cap_type) {
@@ -1081,6 +1093,7 @@
 			break;
 		}
 
+skip_to_next_descriptor:
 		total_len -= length;
 		buffer += length;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/devio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/devio.c
@@ -32,6 +32,7 @@
 #include <linux/usb.h>
 #include <linux/usbdevice_fs.h>
 #include <linux/usb/hcd.h>	/* for usbcore internals */
+#include <linux/usb/quirks.h>
 #include <linux/cdev.h>
 #include <linux/notifier.h>
 #include <linux/security.h>
@@ -173,6 +174,7 @@
 static void dec_usb_memory_use_count(struct usb_memory *usbm, int *count)
 {
 	struct usb_dev_state *ps = usbm->ps;
+	struct usb_hcd *hcd = bus_to_hcd(ps->dev->bus);
 	unsigned long flags;
 
 	spin_lock_irqsave(&ps->lock, flags);
@@ -181,8 +183,8 @@
 		list_del(&usbm->memlist);
 		spin_unlock_irqrestore(&ps->lock, flags);
 
-		usb_free_coherent(ps->dev, usbm->size, usbm->mem,
-				usbm->dma_handle);
+		hcd_buffer_free_pages(hcd, usbm->size,
+				usbm->mem, usbm->dma_handle);
 		usbfs_decrease_memory_usage(
 			usbm->size + sizeof(struct usb_memory));
 		kfree(usbm);
@@ -221,7 +223,7 @@
 	size_t size = vma->vm_end - vma->vm_start;
 	void *mem;
 	unsigned long flags;
-	dma_addr_t dma_handle;
+	dma_addr_t dma_handle = DMA_MAPPING_ERROR;
 	int ret;
 
 	ret = usbfs_increase_memory_usage(size + sizeof(struct usb_memory));
@@ -234,8 +236,8 @@
 		goto error_decrease_mem;
 	}
 
-	mem = usb_alloc_coherent(ps->dev, size, GFP_USER | __GFP_NOWARN,
-			&dma_handle);
+	mem = hcd_buffer_alloc_pages(hcd,
+			size, GFP_USER | __GFP_NOWARN, &dma_handle);
 	if (!mem) {
 		ret = -ENOMEM;
 		goto error_free_usbm;
@@ -251,7 +253,14 @@
 	usbm->vma_use_count = 1;
 	INIT_LIST_HEAD(&usbm->memlist);
 
-	if (hcd->localmem_pool || !hcd_uses_dma(hcd)) {
+	/*
+	 * In DMA-unavailable cases, hcd_buffer_alloc_pages allocates
+	 * normal pages and assigns DMA_MAPPING_ERROR to dma_handle. Check
+	 * whether we are in such cases, and then use remap_pfn_range (or
+	 * dma_mmap_coherent) to map normal (or DMA) pages into the user
+	 * space, respectively.
+	 */
+	if (dma_handle == DMA_MAPPING_ERROR) {
 		if (remap_pfn_range(vma, vma->vm_start,
 				    virt_to_phys(usbm->mem) >> PAGE_SHIFT,
 				    size, vma->vm_page_prot) < 0) {
@@ -726,6 +735,7 @@
 	return 0;
 }
 
+#ifdef CONFIG_PM
 /* The following routines apply to the entire device, not interfaces */
 void usbfs_notify_suspend(struct usb_device *udev)
 {
@@ -744,6 +754,7 @@
 	}
 	mutex_unlock(&usbfs_mutex);
 }
+#endif
 
 struct usb_driver usbfs_driver = {
 	.name =		"usbfs",
@@ -1102,14 +1113,55 @@
 	return 0;
 }
 
+static void usbfs_blocking_completion(struct urb *urb)
+{
+	complete((struct completion *) urb->context);
+}
+
+/*
+ * Much like usb_start_wait_urb, but returns status separately from
+ * actual_length and uses a killable wait.
+ */
+static int usbfs_start_wait_urb(struct urb *urb, int timeout,
+		unsigned int *actlen)
+{
+	DECLARE_COMPLETION_ONSTACK(ctx);
+	unsigned long expire;
+	int rc;
+
+	urb->context = &ctx;
+	urb->complete = usbfs_blocking_completion;
+	*actlen = 0;
+	rc = usb_submit_urb(urb, GFP_KERNEL);
+	if (unlikely(rc))
+		return rc;
+
+	expire = (timeout ? msecs_to_jiffies(timeout) : MAX_SCHEDULE_TIMEOUT);
+	rc = wait_for_completion_killable_timeout(&ctx, expire);
+	if (rc <= 0) {
+		usb_kill_urb(urb);
+		*actlen = urb->actual_length;
+		if (urb->status != -ENOENT)
+			;	/* Completed before it was killed */
+		else if (rc < 0)
+			return -EINTR;
+		else
+			return -ETIMEDOUT;
+	}
+	*actlen = urb->actual_length;
+	return urb->status;
+}
+
 static int do_proc_control(struct usb_dev_state *ps,
 		struct usbdevfs_ctrltransfer *ctrl)
 {
 	struct usb_device *dev = ps->dev;
 	unsigned int tmo;
 	unsigned char *tbuf;
-	unsigned wLength;
+	unsigned int wLength, actlen;
 	int i, pipe, ret;
+	struct urb *urb = NULL;
+	struct usb_ctrlrequest *dr = NULL;
 
 	ret = check_ctrlrecip(ps, ctrl->bRequestType, ctrl->bRequest,
 			      ctrl->wIndex);
@@ -1122,51 +1174,71 @@
 			sizeof(struct usb_ctrlrequest));
 	if (ret)
 		return ret;
+
+	ret = -ENOMEM;
 	tbuf = (unsigned char *)__get_free_page(GFP_KERNEL);
-	if (!tbuf) {
-		ret = -ENOMEM;
+	if (!tbuf)
 		goto done;
-	}
+	urb = usb_alloc_urb(0, GFP_NOIO);
+	if (!urb)
+		goto done;
+	dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_NOIO);
+	if (!dr)
+		goto done;
+
+	dr->bRequestType = ctrl->bRequestType;
+	dr->bRequest = ctrl->bRequest;
+	dr->wValue = cpu_to_le16(ctrl->wValue);
+	dr->wIndex = cpu_to_le16(ctrl->wIndex);
+	dr->wLength = cpu_to_le16(ctrl->wLength);
+
 	tmo = ctrl->timeout;
 	snoop(&dev->dev, "control urb: bRequestType=%02x "
 		"bRequest=%02x wValue=%04x "
 		"wIndex=%04x wLength=%04x\n",
 		ctrl->bRequestType, ctrl->bRequest, ctrl->wValue,
 		ctrl->wIndex, ctrl->wLength);
-	if ((ctrl->bRequestType & USB_DIR_IN) && ctrl->wLength) {
+
+	if ((ctrl->bRequestType & USB_DIR_IN) && wLength) {
 		pipe = usb_rcvctrlpipe(dev, 0);
-		snoop_urb(dev, NULL, pipe, ctrl->wLength, tmo, SUBMIT, NULL, 0);
+		usb_fill_control_urb(urb, dev, pipe, (unsigned char *) dr, tbuf,
+				wLength, NULL, NULL);
+		snoop_urb(dev, NULL, pipe, wLength, tmo, SUBMIT, NULL, 0);
 
 		usb_unlock_device(dev);
-		i = usb_control_msg(dev, pipe, ctrl->bRequest,
-				    ctrl->bRequestType, ctrl->wValue, ctrl->wIndex,
-				    tbuf, ctrl->wLength, tmo);
+		i = usbfs_start_wait_urb(urb, tmo, &actlen);
+
+		/* Linger a bit, prior to the next control message. */
+		if (dev->quirks & USB_QUIRK_DELAY_CTRL_MSG)
+			msleep(200);
 		usb_lock_device(dev);
-		snoop_urb(dev, NULL, pipe, max(i, 0), min(i, 0), COMPLETE,
-			  tbuf, max(i, 0));
-		if ((i > 0) && ctrl->wLength) {
-			if (copy_to_user(ctrl->data, tbuf, i)) {
+		snoop_urb(dev, NULL, pipe, actlen, i, COMPLETE, tbuf, actlen);
+		if (!i && actlen) {
+			if (copy_to_user(ctrl->data, tbuf, actlen)) {
 				ret = -EFAULT;
 				goto done;
 			}
 		}
 	} else {
-		if (ctrl->wLength) {
-			if (copy_from_user(tbuf, ctrl->data, ctrl->wLength)) {
+		if (wLength) {
+			if (copy_from_user(tbuf, ctrl->data, wLength)) {
 				ret = -EFAULT;
 				goto done;
 			}
 		}
 		pipe = usb_sndctrlpipe(dev, 0);
-		snoop_urb(dev, NULL, pipe, ctrl->wLength, tmo, SUBMIT,
-			tbuf, ctrl->wLength);
+		usb_fill_control_urb(urb, dev, pipe, (unsigned char *) dr, tbuf,
+				wLength, NULL, NULL);
+		snoop_urb(dev, NULL, pipe, wLength, tmo, SUBMIT, tbuf, wLength);
 
 		usb_unlock_device(dev);
-		i = usb_control_msg(dev, pipe, ctrl->bRequest,
-				    ctrl->bRequestType, ctrl->wValue, ctrl->wIndex,
-				    tbuf, ctrl->wLength, tmo);
+		i = usbfs_start_wait_urb(urb, tmo, &actlen);
+
+		/* Linger a bit, prior to the next control message. */
+		if (dev->quirks & USB_QUIRK_DELAY_CTRL_MSG)
+			msleep(200);
 		usb_lock_device(dev);
-		snoop_urb(dev, NULL, pipe, max(i, 0), min(i, 0), COMPLETE, NULL, 0);
+		snoop_urb(dev, NULL, pipe, actlen, i, COMPLETE, NULL, 0);
 	}
 	if (i < 0 && i != -EPIPE) {
 		dev_printk(KERN_DEBUG, &dev->dev, "usbfs: USBDEVFS_CONTROL "
@@ -1174,8 +1246,11 @@
 			   current->comm, ctrl->bRequestType, ctrl->bRequest,
 			   ctrl->wLength, i);
 	}
-	ret = i;
+	ret = (i < 0 ? i : actlen);
+
  done:
+	kfree(dr);
+	usb_free_urb(urb);
 	free_page((unsigned long) tbuf);
 	usbfs_decrease_memory_usage(PAGE_SIZE + sizeof(struct urb) +
 			sizeof(struct usb_ctrlrequest));
@@ -1195,10 +1270,11 @@
 		struct usbdevfs_bulktransfer *bulk)
 {
 	struct usb_device *dev = ps->dev;
-	unsigned int tmo, len1, pipe;
-	int len2;
+	unsigned int tmo, len1, len2, pipe;
 	unsigned char *tbuf;
 	int i, ret;
+	struct urb *urb = NULL;
+	struct usb_host_endpoint *ep;
 
 	ret = findintfep(ps->dev, bulk->ep);
 	if (ret < 0)
@@ -1206,14 +1282,17 @@
 	ret = checkintf(ps, ret);
 	if (ret)
 		return ret;
+
+	len1 = bulk->len;
+	if (len1 < 0 || len1 >= (INT_MAX - sizeof(struct urb)))
+		return -EINVAL;
+
 	if (bulk->ep & USB_DIR_IN)
 		pipe = usb_rcvbulkpipe(dev, bulk->ep & 0x7f);
 	else
 		pipe = usb_sndbulkpipe(dev, bulk->ep & 0x7f);
-	if (!usb_maxpacket(dev, pipe, !(bulk->ep & USB_DIR_IN)))
-		return -EINVAL;
-	len1 = bulk->len;
-	if (len1 >= (INT_MAX - sizeof(struct urb)))
+	ep = usb_pipe_endpoint(dev, pipe);
+	if (!ep || !usb_endpoint_maxp(&ep->desc))
 		return -EINVAL;
 	ret = usbfs_increase_memory_usage(len1 + sizeof(struct urb));
 	if (ret)
@@ -1223,17 +1302,29 @@
 	 * len1 can be almost arbitrarily large.  Don't WARN if it's
 	 * too big, just fail the request.
 	 */
+	ret = -ENOMEM;
 	tbuf = kmalloc(len1, GFP_KERNEL | __GFP_NOWARN);
-	if (!tbuf) {
-		ret = -ENOMEM;
+	if (!tbuf)
+		goto done;
+	urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!urb)
 		goto done;
+
+	if ((ep->desc.bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+			USB_ENDPOINT_XFER_INT) {
+		pipe = (pipe & ~(3 << 30)) | (PIPE_INTERRUPT << 30);
+		usb_fill_int_urb(urb, dev, pipe, tbuf, len1,
+				NULL, NULL, ep->desc.bInterval);
+	} else {
+		usb_fill_bulk_urb(urb, dev, pipe, tbuf, len1, NULL, NULL);
 	}
+
 	tmo = bulk->timeout;
 	if (bulk->ep & 0x80) {
 		snoop_urb(dev, NULL, pipe, len1, tmo, SUBMIT, NULL, 0);
 
 		usb_unlock_device(dev);
-		i = usb_bulk_msg(dev, pipe, tbuf, len1, &len2, tmo);
+		i = usbfs_start_wait_urb(urb, tmo, &len2);
 		usb_lock_device(dev);
 		snoop_urb(dev, NULL, pipe, len2, i, COMPLETE, tbuf, len2);
 
@@ -1253,12 +1344,13 @@
 		snoop_urb(dev, NULL, pipe, len1, tmo, SUBMIT, tbuf, len1);
 
 		usb_unlock_device(dev);
-		i = usb_bulk_msg(dev, pipe, tbuf, len1, &len2, tmo);
+		i = usbfs_start_wait_urb(urb, tmo, &len2);
 		usb_lock_device(dev);
 		snoop_urb(dev, NULL, pipe, len2, i, COMPLETE, NULL, 0);
 	}
 	ret = (i < 0 ? i : len2);
  done:
+	usb_free_urb(urb);
 	kfree(tbuf);
 	usbfs_decrease_memory_usage(len1 + sizeof(struct urb));
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/hcd-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/hcd-pci.c
@@ -616,10 +616,10 @@
 	.suspend_noirq	= hcd_pci_suspend_noirq,
 	.resume_noirq	= hcd_pci_resume_noirq,
 	.resume		= hcd_pci_resume,
-	.freeze		= check_root_hub_suspended,
+	.freeze		= hcd_pci_suspend,
 	.freeze_noirq	= check_root_hub_suspended,
 	.thaw_noirq	= NULL,
-	.thaw		= NULL,
+	.thaw		= hcd_pci_resume,
 	.poweroff	= hcd_pci_suspend,
 	.poweroff_noirq	= hcd_pci_suspend_noirq,
 	.restore_noirq	= hcd_pci_resume_noirq,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/hcd.c
@@ -753,6 +753,7 @@
 {
 	struct urb	*urb;
 	int		length;
+	int		status;
 	unsigned long	flags;
 	char		buffer[6];	/* Any root hubs with > 31 ports? */
 
@@ -770,11 +771,17 @@
 		if (urb) {
 			clear_bit(HCD_FLAG_POLL_PENDING, &hcd->flags);
 			hcd->status_urb = NULL;
+			if (urb->transfer_buffer_length >= length) {
+				status = 0;
+			} else {
+				status = -EOVERFLOW;
+				length = urb->transfer_buffer_length;
+			}
 			urb->actual_length = length;
 			memcpy(urb->transfer_buffer, buffer, length);
 
 			usb_hcd_unlink_urb_from_ep(hcd, urb);
-			usb_hcd_giveback_urb(hcd, urb, 0);
+			usb_hcd_giveback_urb(hcd, urb, status);
 		} else {
 			length = 0;
 			set_bit(HCD_FLAG_POLL_PENDING, &hcd->flags);
@@ -976,6 +983,7 @@
 {
 	struct device *parent_dev = hcd->self.controller;
 	struct usb_device *usb_dev = hcd->self.root_hub;
+	struct usb_device_descriptor *descr;
 	const int devnum = 1;
 	int retval;
 
@@ -987,13 +995,16 @@
 	mutex_lock(&usb_bus_idr_lock);
 
 	usb_dev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
-	retval = usb_get_device_descriptor(usb_dev, USB_DT_DEVICE_SIZE);
-	if (retval != sizeof usb_dev->descriptor) {
+	descr = usb_get_device_descriptor(usb_dev);
+	if (IS_ERR(descr)) {
+		retval = PTR_ERR(descr);
 		mutex_unlock(&usb_bus_idr_lock);
 		dev_dbg (parent_dev, "can't read %s device descriptor %d\n",
 				dev_name(&usb_dev->dev), retval);
-		return (retval < 0) ? retval : -EMSGSIZE;
+		return retval;
 	}
+	usb_dev->descriptor = *descr;
+	kfree(descr);
 
 	if (le16_to_cpu(usb_dev->descriptor.bcdUSB) >= 0x0201) {
 		retval = usb_get_bos_descriptor(usb_dev);
@@ -1556,6 +1567,13 @@
 		urb->hcpriv = NULL;
 		INIT_LIST_HEAD(&urb->urb_list);
 		atomic_dec(&urb->use_count);
+		/*
+		 * Order the write of urb->use_count above before the read
+		 * of urb->reject below.  Pairs with the memory barriers in
+		 * usb_kill_urb() and usb_poison_urb().
+		 */
+		smp_mb__after_atomic();
+
 		atomic_dec(&urb->dev->urbnum);
 		if (atomic_read(&urb->reject))
 			wake_up(&usb_kill_urb_queue);
@@ -1658,6 +1676,13 @@
 
 	usb_anchor_resume_wakeups(anchor);
 	atomic_dec(&urb->use_count);
+	/*
+	 * Order the write of urb->use_count above before the read
+	 * of urb->reject below.  Pairs with the memory barriers in
+	 * usb_kill_urb() and usb_poison_urb().
+	 */
+	smp_mb__after_atomic();
+
 	if (unlikely(atomic_read(&urb->reject)))
 		wake_up(&usb_kill_urb_queue);
 	usb_put_urb(urb);
@@ -1670,7 +1695,6 @@
 
 	spin_lock_irq(&bh->lock);
 	bh->running = true;
- restart:
 	list_replace_init(&bh->head, &local_list);
 	spin_unlock_irq(&bh->lock);
 
@@ -1684,10 +1708,17 @@
 		bh->completing_ep = NULL;
 	}
 
-	/* check if there are new URBs to giveback */
+	/*
+	 * giveback new URBs next time to prevent this function
+	 * from not exiting for a long time.
+	 */
 	spin_lock_irq(&bh->lock);
-	if (!list_empty(&bh->head))
-		goto restart;
+	if (!list_empty(&bh->head)) {
+		if (bh->high_prio)
+			tasklet_hi_schedule(&bh->bh);
+		else
+			tasklet_schedule(&bh->bh);
+	}
 	bh->running = false;
 	spin_unlock_irq(&bh->lock);
 }
@@ -1716,7 +1747,7 @@
 void usb_hcd_giveback_urb(struct usb_hcd *hcd, struct urb *urb, int status)
 {
 	struct giveback_urb_bh *bh;
-	bool running, high_prio_bh;
+	bool running;
 
 	/* pass status to tasklet via unlinked */
 	if (likely(!urb->unlinked))
@@ -1727,13 +1758,10 @@
 		return;
 	}
 
-	if (usb_pipeisoc(urb->pipe) || usb_pipeint(urb->pipe)) {
+	if (usb_pipeisoc(urb->pipe) || usb_pipeint(urb->pipe))
 		bh = &hcd->high_prio_bh;
-		high_prio_bh = true;
-	} else {
+	else
 		bh = &hcd->low_prio_bh;
-		high_prio_bh = false;
-	}
 
 	spin_lock(&bh->lock);
 	list_add_tail(&urb->urb_list, &bh->head);
@@ -1742,7 +1770,7 @@
 
 	if (running)
 		;
-	else if (high_prio_bh)
+	else if (bh->high_prio)
 		tasklet_hi_schedule(&bh->bh);
 	else
 		tasklet_schedule(&bh->bh);
@@ -2938,6 +2966,7 @@
 
 	/* initialize tasklets */
 	init_giveback_urb_bh(&hcd->high_prio_bh);
+	hcd->high_prio_bh.high_prio = true;
 	init_giveback_urb_bh(&hcd->low_prio_bh);
 
 	/* enable irqs just before we start the controller,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/hub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/hub.c
@@ -43,8 +43,11 @@
 #define USB_PRODUCT_USB5534B			0x5534
 #define USB_VENDOR_CYPRESS			0x04b4
 #define USB_PRODUCT_CY7C65632			0x6570
-#define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND	0x01
-#define HUB_QUIRK_DISABLE_AUTOSUSPEND		0x02
+#define USB_VENDOR_TEXAS_INSTRUMENTS		0x0451
+#define USB_PRODUCT_TUSB8041_USB3		0x8140
+#define USB_PRODUCT_TUSB8041_USB2		0x8142
+#define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND	BIT(0)
+#define HUB_QUIRK_DISABLE_AUTOSUSPEND		BIT(1)
 
 #define USB_TP_TRANSMISSION_DELAY	40	/* ns */
 #define USB_TP_TRANSMISSION_DELAY_MAX	65535	/* ns */
@@ -113,7 +116,6 @@
 #define HUB_DEBOUNCE_STEP	  25
 #define HUB_DEBOUNCE_STABLE	 100
 
-static void hub_release(struct kref *kref);
 static int usb_reset_and_verify_device(struct usb_device *udev);
 static int hub_port_disable(struct usb_hub *hub, int port1, int set_state);
 static bool hub_port_warm_reset_required(struct usb_hub *hub, int port1,
@@ -147,6 +149,10 @@
 	if (udev->quirks & USB_QUIRK_NO_LPM)
 		return 0;
 
+	/* Skip if the device BOS descriptor couldn't be read */
+	if (!udev->bos)
+		return 0;
+
 	/* USB 2.1 (and greater) devices indicate LPM support through
 	 * their USB 2.0 Extended Capabilities BOS descriptor.
 	 */
@@ -323,6 +329,10 @@
 	if (!udev->lpm_capable || udev->speed < USB_SPEED_SUPER)
 		return;
 
+	/* Skip if the device BOS descriptor couldn't be read */
+	if (!udev->bos)
+		return;
+
 	hub = usb_hub_to_struct_hub(udev->parent);
 	/* It doesn't take time to transition the roothub into U0, since it
 	 * doesn't have an upstream link.
@@ -667,14 +677,14 @@
 	 */
 	intf = to_usb_interface(hub->intfdev);
 	usb_autopm_get_interface_no_resume(intf);
-	kref_get(&hub->kref);
+	hub_get(hub);
 
 	if (queue_work(hub_wq, &hub->events))
 		return;
 
 	/* the work has already been scheduled */
 	usb_autopm_put_interface_async(intf);
-	kref_put(&hub->kref, hub_release);
+	hub_put(hub);
 }
 
 void usb_kick_hub_wq(struct usb_device *hdev)
@@ -828,9 +838,9 @@
  *
  * Return: 0 if successful. A negative error code otherwise.
  */
-int usb_hub_set_port_power(struct usb_device *hdev, struct usb_hub *hub,
-			   int port1, bool set)
+int usb_hub_set_port_power(struct usb_hub *hub, int port1, bool set)
 {
+	struct usb_device *hdev = hub->hdev;
 	int ret;
 
 	if (set)
@@ -1042,7 +1052,7 @@
 			goto init2;
 		goto init3;
 	}
-	kref_get(&hub->kref);
+	hub_get(hub);
 
 	/* The superspeed hub except for root hub has to use Hub Depth
 	 * value as an offset into the route string to locate the bits
@@ -1110,7 +1120,10 @@
 		} else {
 			hub_power_on(hub, true);
 		}
-	}
+	/* Give some time on remote wakeup to let links to transit to U0 */
+	} else if (hub_is_superspeed(hub->hdev))
+		msleep(20);
+
  init2:
 
 	/*
@@ -1225,7 +1238,7 @@
 			 */
 			if (portchange || (hub_is_superspeed(hub->hdev) &&
 						port_resumed))
-				set_bit(port1, hub->change_bits);
+				set_bit(port1, hub->event_bits);
 
 		} else if (udev->persist_enabled) {
 #ifdef CONFIG_PM
@@ -1287,7 +1300,7 @@
 		device_unlock(&hdev->dev);
 	}
 
-	kref_put(&hub->kref, hub_release);
+	hub_put(hub);
 }
 
 /* Implement the continuations for the delays above */
@@ -1703,6 +1716,16 @@
 	kfree(hub);
 }
 
+void hub_get(struct usb_hub *hub)
+{
+	kref_get(&hub->kref);
+}
+
+void hub_put(struct usb_hub *hub)
+{
+	kref_put(&hub->kref, hub_release);
+}
+
 static unsigned highspeed_hubs;
 
 static void hub_disconnect(struct usb_interface *intf)
@@ -1749,7 +1772,7 @@
 	if (hub->quirk_disable_autosuspend)
 		usb_autopm_put_interface(intf);
 
-	kref_put(&hub->kref, hub_release);
+	hub_put(hub);
 }
 
 static bool hub_descriptor_is_sane(struct usb_host_interface *desc)
@@ -1781,6 +1804,17 @@
 	hdev = interface_to_usbdev(intf);
 
 	/*
+	 * The USB 2.0 spec prohibits hubs from having more than one
+	 * configuration or interface, and we rely on this prohibition.
+	 * Refuse to accept a device that violates it.
+	 */
+	if (hdev->descriptor.bNumConfigurations > 1 ||
+			hdev->actconfig->desc.bNumInterfaces > 1) {
+		dev_err(&intf->dev, "Invalid hub with more than one config or interface\n");
+		return -EINVAL;
+	}
+
+	/*
 	 * Set default autosuspend delay as 0 to speedup bus suspend,
 	 * based on the below considerations:
 	 *
@@ -2354,17 +2388,25 @@
 			}
 		} else if (desc->bLength == sizeof
 				(struct usb_otg_descriptor)) {
-			/* Set a_alt_hnp_support for legacy otg device */
-			err = usb_control_msg(udev,
-				usb_sndctrlpipe(udev, 0),
-				USB_REQ_SET_FEATURE, 0,
-				USB_DEVICE_A_ALT_HNP_SUPPORT,
-				0, NULL, 0,
-				USB_CTRL_SET_TIMEOUT);
-			if (err < 0)
-				dev_err(&udev->dev,
-					"set a_alt_hnp_support failed: %d\n",
-					err);
+			/*
+			 * We are operating on a legacy OTP device
+			 * These should be told that they are operating
+			 * on the wrong port if we have another port that does
+			 * support HNP
+			 */
+			if (bus->otg_port != 0) {
+				/* Set a_alt_hnp_support for legacy otg device */
+				err = usb_control_msg(udev,
+					usb_sndctrlpipe(udev, 0),
+					USB_REQ_SET_FEATURE, 0,
+					USB_DEVICE_A_ALT_HNP_SUPPORT,
+					0, NULL, 0,
+					USB_CTRL_SET_TIMEOUT);
+				if (err < 0)
+					dev_err(&udev->dev,
+						"set a_alt_hnp_support failed: %d\n",
+						err);
+			}
 		}
 	}
 #endif
@@ -2376,9 +2418,8 @@
  * usb_enumerate_device - Read device configs/intfs/otg (usbcore-internal)
  * @udev: newly addressed device (in ADDRESS state)
  *
- * This is only called by usb_new_device() and usb_authorize_device()
- * and FIXME -- all comments that apply to them apply here wrt to
- * environment.
+ * This is only called by usb_new_device() -- all comments that apply there
+ * apply here wrt to environment.
  *
  * If the device is WUSB and not authorized, we don't attempt to read
  * the string descriptors, as they will be errored out by the device
@@ -2575,13 +2616,13 @@
 		err = sysfs_create_link(&udev->dev.kobj,
 				&port_dev->dev.kobj, "port");
 		if (err)
-			goto fail;
+			goto out_del_dev;
 
 		err = sysfs_create_link(&port_dev->dev.kobj,
 				&udev->dev.kobj, "device");
 		if (err) {
 			sysfs_remove_link(&udev->dev.kobj, "port");
-			goto fail;
+			goto out_del_dev;
 		}
 
 		if (!test_and_set_bit(port1, hub->child_usage_bits))
@@ -2593,6 +2634,8 @@
 	pm_runtime_put_sync_autosuspend(&udev->dev);
 	return err;
 
+out_del_dev:
+	device_del(&udev->dev);
 fail:
 	usb_set_device_state(udev, USB_STATE_NOTATTACHED);
 	pm_runtime_disable(&udev->dev);
@@ -2644,12 +2687,17 @@
 	}
 
 	if (usb_dev->wusb) {
-		result = usb_get_device_descriptor(usb_dev, sizeof(usb_dev->descriptor));
-		if (result < 0) {
+		struct usb_device_descriptor *descr;
+
+		descr = usb_get_device_descriptor(usb_dev);
+		if (IS_ERR(descr)) {
+			result = PTR_ERR(descr);
 			dev_err(&usb_dev->dev, "can't re-read device descriptor for "
 				"authorization: %d\n", result);
 			goto error_device_descriptor;
 		}
+		usb_dev->descriptor = *descr;
+		kfree(descr);
 	}
 
 	usb_dev->authorized = 1;
@@ -2688,13 +2736,17 @@
 static enum usb_ssp_rate get_port_ssp_rate(struct usb_device *hdev,
 					   u32 ext_portstatus)
 {
-	struct usb_ssp_cap_descriptor *ssp_cap = hdev->bos->ssp_cap;
+	struct usb_ssp_cap_descriptor *ssp_cap;
 	u32 attr;
 	u8 speed_id;
 	u8 ssac;
 	u8 lanes;
 	int i;
 
+	if (!hdev->bos)
+		goto out;
+
+	ssp_cap = hdev->bos->ssp_cap;
 	if (!ssp_cap)
 		goto out;
 
@@ -2829,6 +2881,39 @@
 		|| link_state == USB_SS_PORT_LS_COMP_MOD;
 }
 
+static bool hub_port_power_cycle_required(struct usb_hub *hub, int port1,
+		u16 portstatus)
+{
+	u16 link_state;
+
+	if (!hub_is_superspeed(hub->hdev))
+		return false;
+
+	link_state = portstatus & USB_PORT_STAT_LINK_STATE;
+	return link_state == USB_SS_PORT_LS_SS_DISABLED;
+}
+
+static void hub_port_power_cycle(struct usb_hub *hub, int port1)
+{
+	struct usb_port *port_dev = hub->ports[port1  - 1];
+	int ret;
+
+	ret = usb_hub_set_port_power(hub, port1, false);
+	if (ret) {
+		dev_info(&port_dev->dev, "failed to disable port power\n");
+		return;
+	}
+
+	msleep(2 * hub_power_on_good_delay(hub));
+	ret = usb_hub_set_port_power(hub, port1, true);
+	if (ret) {
+		dev_info(&port_dev->dev, "failed to enable port power\n");
+		return;
+	}
+
+	msleep(hub_power_on_good_delay(hub));
+}
+
 static int hub_port_wait_reset(struct usb_hub *hub, int port1,
 			struct usb_device *udev, unsigned int delay, bool warm)
 {
@@ -3700,6 +3785,10 @@
 	if (status < 0) {
 		dev_dbg(&udev->dev, "can't resume, status %d\n", status);
 		hub_port_logical_disconnect(hub, port1);
+		if (hub_port_power_cycle_required(hub, port1, portstatus)) {
+			dev_dbg(&udev->dev, "device in disabled state, attempt power cycle\n");
+			hub_port_power_cycle(hub, port1);
+		}
 	} else  {
 		/* Try to enable USB2 hardware LPM */
 		usb_enable_usb2_hardware_lpm(udev);
@@ -4176,8 +4265,15 @@
 		enum usb3_link_state state)
 {
 	int timeout, ret;
-	__u8 u1_mel = udev->bos->ss_cap->bU1devExitLat;
-	__le16 u2_mel = udev->bos->ss_cap->bU2DevExitLat;
+	__u8 u1_mel;
+	__le16 u2_mel;
+
+	/* Skip if the device BOS descriptor couldn't be read */
+	if (!udev->bos)
+		return;
+
+	u1_mel = udev->bos->ss_cap->bU1devExitLat;
+	u2_mel = udev->bos->ss_cap->bU2DevExitLat;
 
 	/* If the device says it doesn't have *any* exit latency to come out of
 	 * U1 or U2, it's probably lying.  Assume it doesn't implement that link
@@ -4588,7 +4684,6 @@
 EXPORT_SYMBOL_GPL(usb_ep0_reinit);
 
 #define usb_sndaddr0pipe()	(PIPE_CONTROL << 30)
-#define usb_rcvaddr0pipe()	((PIPE_CONTROL << 30) | USB_DIR_IN)
 
 static int hub_set_address(struct usb_device *udev, int devnum)
 {
@@ -4606,7 +4701,7 @@
 	if (udev->state != USB_STATE_DEFAULT)
 		return -EINVAL;
 	if (hcd->driver->address_device)
-		retval = hcd->driver->address_device(hcd, udev);
+		retval = hcd->driver->address_device(hcd, udev, USB_CTRL_SET_TIMEOUT);
 	else
 		retval = usb_control_msg(udev, usb_sndaddr0pipe(),
 				USB_REQ_SET_ADDRESS, 0, devnum, 0,
@@ -4661,6 +4756,67 @@
 	return hcd->driver->enable_device(hcd, udev);
 }
 
+/*
+ * Get the bMaxPacketSize0 value during initialization by reading the
+ * device's device descriptor.  Since we don't already know this value,
+ * the transfer is unsafe and it ignores I/O errors, only testing for
+ * reasonable received values.
+ *
+ * For "old scheme" initialization, size will be 8 so we read just the
+ * start of the device descriptor, which should work okay regardless of
+ * the actual bMaxPacketSize0 value.  For "new scheme" initialization,
+ * size will be 64 (and buf will point to a sufficiently large buffer),
+ * which might not be kosher according to the USB spec but it's what
+ * Windows does and what many devices expect.
+ *
+ * Returns: bMaxPacketSize0 or a negative error code.
+ */
+static int get_bMaxPacketSize0(struct usb_device *udev,
+		struct usb_device_descriptor *buf, int size, bool first_time)
+{
+	int i, rc;
+
+	/*
+	 * Retry on all errors; some devices are flakey.
+	 * 255 is for WUSB devices, we actually need to use
+	 * 512 (WUSB1.0[4.8.1]).
+	 */
+	for (i = 0; i < GET_MAXPACKET0_TRIES; ++i) {
+		/* Start with invalid values in case the transfer fails */
+		buf->bDescriptorType = buf->bMaxPacketSize0 = 0;
+		rc = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
+				USB_REQ_GET_DESCRIPTOR, USB_DIR_IN,
+				USB_DT_DEVICE << 8, 0,
+				buf, size,
+				initial_descriptor_timeout);
+		switch (buf->bMaxPacketSize0) {
+		case 8: case 16: case 32: case 64: case 9:
+			if (buf->bDescriptorType == USB_DT_DEVICE) {
+				rc = buf->bMaxPacketSize0;
+				break;
+			}
+			fallthrough;
+		default:
+			if (rc >= 0)
+				rc = -EPROTO;
+			break;
+		}
+
+		/*
+		 * Some devices time out if they are powered on
+		 * when already connected. They need a second
+		 * reset, so return early. But only on the first
+		 * attempt, lest we get into a time-out/reset loop.
+		 */
+		if (rc > 0 || (rc == -ETIMEDOUT && first_time &&
+				udev->speed > USB_SPEED_FULL))
+			break;
+	}
+	return rc;
+}
+
+#define GET_DESCRIPTOR_BUFSIZE	64
+
 /* Reset device, (re)assign address, get device descriptor.
  * Device connection must be stable, no more debouncing needed.
  * Returns device in USB_STATE_ADDRESS, except on error.
@@ -4670,10 +4826,17 @@
  * the port lock.  For a newly detected device that is not accessible
  * through any global pointers, it's not necessary to lock the device,
  * but it is still necessary to lock the port.
+ *
+ * For a newly detected device, @dev_descr must be NULL.  The device
+ * descriptor retrieved from the device will then be stored in
+ * @udev->descriptor.  For an already existing device, @dev_descr
+ * must be non-NULL.  The device descriptor will be stored there,
+ * not in @udev->descriptor, because descriptors for registered
+ * devices are meant to be immutable.
  */
 static int
 hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1,
-		int retry_counter)
+		int retry_counter, struct usb_device_descriptor *dev_descr)
 {
 	struct usb_device	*hdev = hub->hdev;
 	struct usb_hcd		*hcd = bus_to_hcd(hdev->bus);
@@ -4685,6 +4848,13 @@
 	int			devnum = udev->devnum;
 	const char		*driver_name;
 	bool			do_new_scheme;
+	const bool		initial = !dev_descr;
+	int			maxp0;
+	struct usb_device_descriptor	*buf, *descr;
+
+	buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO);
+	if (!buf)
+		return -ENOMEM;
 
 	/* root hub ports have a slightly longer reset period
 	 * (from USB 2.0 spec, section 7.1.7.5)
@@ -4700,8 +4870,6 @@
 	if (oldspeed == USB_SPEED_LOW)
 		delay = HUB_LONG_RESET_TIME;
 
-	mutex_lock(hcd->address0_mutex);
-
 	/* Reset the device; full speed may morph to high speed */
 	/* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */
 	retval = hub_port_reset(hub, port1, udev, delay, false);
@@ -4719,32 +4887,34 @@
 	}
 	oldspeed = udev->speed;
 
-	/* USB 2.0 section 5.5.3 talks about ep0 maxpacket ...
-	 * it's fixed size except for full speed devices.
-	 * For Wireless USB devices, ep0 max packet is always 512 (tho
-	 * reported as 0xff in the device descriptor). WUSB1.0[4.8.1].
-	 */
-	switch (udev->speed) {
-	case USB_SPEED_SUPER_PLUS:
-	case USB_SPEED_SUPER:
-	case USB_SPEED_WIRELESS:	/* fixed at 512 */
-		udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512);
-		break;
-	case USB_SPEED_HIGH:		/* fixed at 64 */
-		udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
-		break;
-	case USB_SPEED_FULL:		/* 8, 16, 32, or 64 */
-		/* to determine the ep0 maxpacket size, try to read
-		 * the device descriptor to get bMaxPacketSize0 and
-		 * then correct our initial guess.
+	if (initial) {
+		/* USB 2.0 section 5.5.3 talks about ep0 maxpacket ...
+		 * it's fixed size except for full speed devices.
+		 * For Wireless USB devices, ep0 max packet is always 512 (tho
+		 * reported as 0xff in the device descriptor). WUSB1.0[4.8.1].
 		 */
-		udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
-		break;
-	case USB_SPEED_LOW:		/* fixed at 8 */
-		udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8);
-		break;
-	default:
-		goto fail;
+		switch (udev->speed) {
+		case USB_SPEED_SUPER_PLUS:
+		case USB_SPEED_SUPER:
+		case USB_SPEED_WIRELESS:	/* fixed at 512 */
+			udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512);
+			break;
+		case USB_SPEED_HIGH:		/* fixed at 64 */
+			udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
+			break;
+		case USB_SPEED_FULL:		/* 8, 16, 32, or 64 */
+			/* to determine the ep0 maxpacket size, try to read
+			 * the device descriptor to get bMaxPacketSize0 and
+			 * then correct our initial guess.
+			 */
+			udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
+			break;
+		case USB_SPEED_LOW:		/* fixed at 8 */
+			udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8);
+			break;
+		default:
+			goto fail;
+		}
 	}
 
 	if (udev->speed == USB_SPEED_WIRELESS)
@@ -4767,22 +4937,24 @@
 	if (udev->speed < USB_SPEED_SUPER)
 		dev_info(&udev->dev,
 				"%s %s USB device number %d using %s\n",
-				(udev->config) ? "reset" : "new", speed,
+				(initial ? "new" : "reset"), speed,
 				devnum, driver_name);
 
-	/* Set up TT records, if needed  */
-	if (hdev->tt) {
-		udev->tt = hdev->tt;
-		udev->ttport = hdev->ttport;
-	} else if (udev->speed != USB_SPEED_HIGH
-			&& hdev->speed == USB_SPEED_HIGH) {
-		if (!hub->tt.hub) {
-			dev_err(&udev->dev, "parent hub has no TT\n");
-			retval = -EINVAL;
-			goto fail;
+	if (initial) {
+		/* Set up TT records, if needed  */
+		if (hdev->tt) {
+			udev->tt = hdev->tt;
+			udev->ttport = hdev->ttport;
+		} else if (udev->speed != USB_SPEED_HIGH
+				&& hdev->speed == USB_SPEED_HIGH) {
+			if (!hub->tt.hub) {
+				dev_err(&udev->dev, "parent hub has no TT\n");
+				retval = -EINVAL;
+				goto fail;
+			}
+			udev->tt = &hub->tt;
+			udev->ttport = port1;
 		}
-		udev->tt = &hub->tt;
-		udev->ttport = port1;
 	}
 
 	/* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way?
@@ -4801,9 +4973,6 @@
 
 	for (retries = 0; retries < GET_DESCRIPTOR_TRIES; (++retries, msleep(100))) {
 		if (do_new_scheme) {
-			struct usb_device_descriptor *buf;
-			int r = 0;
-
 			retval = hub_enable_device(udev);
 			if (retval < 0) {
 				dev_err(&udev->dev,
@@ -4812,52 +4981,14 @@
 				goto fail;
 			}
 
-#define GET_DESCRIPTOR_BUFSIZE	64
-			buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO);
-			if (!buf) {
-				retval = -ENOMEM;
-				continue;
-			}
-
-			/* Retry on all errors; some devices are flakey.
-			 * 255 is for WUSB devices, we actually need to use
-			 * 512 (WUSB1.0[4.8.1]).
-			 */
-			for (operations = 0; operations < GET_MAXPACKET0_TRIES;
-					++operations) {
-				buf->bMaxPacketSize0 = 0;
-				r = usb_control_msg(udev, usb_rcvaddr0pipe(),
-					USB_REQ_GET_DESCRIPTOR, USB_DIR_IN,
-					USB_DT_DEVICE << 8, 0,
-					buf, GET_DESCRIPTOR_BUFSIZE,
-					initial_descriptor_timeout);
-				switch (buf->bMaxPacketSize0) {
-				case 8: case 16: case 32: case 64: case 255:
-					if (buf->bDescriptorType ==
-							USB_DT_DEVICE) {
-						r = 0;
-						break;
-					}
-					fallthrough;
-				default:
-					if (r == 0)
-						r = -EPROTO;
-					break;
-				}
-				/*
-				 * Some devices time out if they are powered on
-				 * when already connected. They need a second
-				 * reset. But only on the first attempt,
-				 * lest we get into a time out/reset loop
-				 */
-				if (r == 0 || (r == -ETIMEDOUT &&
-						retries == 0 &&
-						udev->speed > USB_SPEED_FULL))
-					break;
+			maxp0 = get_bMaxPacketSize0(udev, buf,
+					GET_DESCRIPTOR_BUFSIZE, retries == 0);
+			if (maxp0 > 0 && !initial &&
+					maxp0 != udev->descriptor.bMaxPacketSize0) {
+				dev_err(&udev->dev, "device reset changed ep0 maxpacket size!\n");
+				retval = -ENODEV;
+				goto fail;
 			}
-			udev->descriptor.bMaxPacketSize0 =
-					buf->bMaxPacketSize0;
-			kfree(buf);
 
 			retval = hub_port_reset(hub, port1, udev, delay, false);
 			if (retval < 0)		/* error or disconnect */
@@ -4868,14 +4999,13 @@
 				retval = -ENODEV;
 				goto fail;
 			}
-			if (r) {
-				if (r != -ENODEV)
+			if (maxp0 < 0) {
+				if (maxp0 != -ENODEV)
 					dev_err(&udev->dev, "device descriptor read/64, error %d\n",
-							r);
-				retval = -EMSGSIZE;
+							maxp0);
+				retval = maxp0;
 				continue;
 			}
-#undef GET_DESCRIPTOR_BUFSIZE
 		}
 
 		/*
@@ -4921,18 +5051,22 @@
 				break;
 		}
 
-		retval = usb_get_device_descriptor(udev, 8);
-		if (retval < 8) {
+		/* !do_new_scheme || wusb */
+		maxp0 = get_bMaxPacketSize0(udev, buf, 8, retries == 0);
+		if (maxp0 < 0) {
+			retval = maxp0;
 			if (retval != -ENODEV)
 				dev_err(&udev->dev,
 					"device descriptor read/8, error %d\n",
 					retval);
-			if (retval >= 0)
-				retval = -EMSGSIZE;
 		} else {
 			u32 delay;
 
-			retval = 0;
+			if (!initial && maxp0 != udev->descriptor.bMaxPacketSize0) {
+				dev_err(&udev->dev, "device reset changed ep0 maxpacket size!\n");
+				retval = -ENODEV;
+				goto fail;
+			}
 
 			delay = udev->parent->hub_delay;
 			udev->hub_delay = min_t(u32, delay,
@@ -4951,48 +5085,62 @@
 		goto fail;
 
 	/*
-	 * Some superspeed devices have finished the link training process
-	 * and attached to a superspeed hub port, but the device descriptor
-	 * got from those devices show they aren't superspeed devices. Warm
-	 * reset the port attached by the devices can fix them.
-	 */
-	if ((udev->speed >= USB_SPEED_SUPER) &&
-			(le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) {
-		dev_err(&udev->dev, "got a wrong device descriptor, "
-				"warm reset device\n");
-		hub_port_reset(hub, port1, udev,
-				HUB_BH_RESET_TIME, true);
-		retval = -EINVAL;
-		goto fail;
+	 * Check the ep0 maxpacket guess and correct it if necessary.
+	 * maxp0 is the value stored in the device descriptor;
+	 * i is the value it encodes (logarithmic for SuperSpeed or greater).
+	 */
+	i = maxp0;
+	if (udev->speed >= USB_SPEED_SUPER) {
+		if (maxp0 <= 16)
+			i = 1 << maxp0;
+		else
+			i = 0;		/* Invalid */
 	}
-
-	if (udev->descriptor.bMaxPacketSize0 == 0xff ||
-			udev->speed >= USB_SPEED_SUPER)
-		i = 512;
-	else
-		i = udev->descriptor.bMaxPacketSize0;
-	if (usb_endpoint_maxp(&udev->ep0.desc) != i) {
-		if (udev->speed == USB_SPEED_LOW ||
-				!(i == 8 || i == 16 || i == 32 || i == 64)) {
-			dev_err(&udev->dev, "Invalid ep0 maxpacket: %d\n", i);
-			retval = -EMSGSIZE;
-			goto fail;
-		}
+	if (usb_endpoint_maxp(&udev->ep0.desc) == i) {
+		;	/* Initial ep0 maxpacket guess is right */
+	} else if (((udev->speed == USB_SPEED_FULL ||
+				udev->speed == USB_SPEED_HIGH) &&
+			(i == 8 || i == 16 || i == 32 || i == 64)) ||
+			(udev->speed >= USB_SPEED_SUPER && i > 0)) {
+		/* Initial guess is wrong; use the descriptor's value */
 		if (udev->speed == USB_SPEED_FULL)
 			dev_dbg(&udev->dev, "ep0 maxpacket = %d\n", i);
 		else
 			dev_warn(&udev->dev, "Using ep0 maxpacket: %d\n", i);
 		udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i);
 		usb_ep0_reinit(udev);
+	} else {
+		/* Initial guess is wrong and descriptor's value is invalid */
+		dev_err(&udev->dev, "Invalid ep0 maxpacket: %d\n", maxp0);
+		retval = -EMSGSIZE;
+		goto fail;
 	}
 
-	retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE);
-	if (retval < (signed)sizeof(udev->descriptor)) {
+	descr = usb_get_device_descriptor(udev);
+	if (IS_ERR(descr)) {
+		retval = PTR_ERR(descr);
 		if (retval != -ENODEV)
 			dev_err(&udev->dev, "device descriptor read/all, error %d\n",
 					retval);
-		if (retval >= 0)
-			retval = -ENOMSG;
+		goto fail;
+	}
+	if (initial)
+		udev->descriptor = *descr;
+	else
+		*dev_descr = *descr;
+	kfree(descr);
+
+	/*
+	 * Some superspeed devices have finished the link training process
+	 * and attached to a superspeed hub port, but the device descriptor
+	 * got from those devices show they aren't superspeed devices. Warm
+	 * reset the port attached by the devices can fix them.
+	 */
+	if ((udev->speed >= USB_SPEED_SUPER) &&
+			(le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) {
+		dev_err(&udev->dev, "got a wrong device descriptor, warm reset device\n");
+		hub_port_reset(hub, port1, udev, HUB_BH_RESET_TIME, true);
+		retval = -EINVAL;
 		goto fail;
 	}
 
@@ -5016,7 +5164,7 @@
 		hub_port_disable(hub, port1, 0);
 		update_devnum(udev, devnum);	/* for disconnect processing */
 	}
-	mutex_unlock(hcd->address0_mutex);
+	kfree(buf);
 	return retval;
 }
 
@@ -5097,7 +5245,7 @@
 
 
 static int descriptors_changed(struct usb_device *udev,
-		struct usb_device_descriptor *old_device_descriptor,
+		struct usb_device_descriptor *new_device_descriptor,
 		struct usb_host_bos *old_bos)
 {
 	int		changed = 0;
@@ -5108,8 +5256,8 @@
 	int		length;
 	char		*buf;
 
-	if (memcmp(&udev->descriptor, old_device_descriptor,
-			sizeof(*old_device_descriptor)) != 0)
+	if (memcmp(&udev->descriptor, new_device_descriptor,
+			sizeof(*new_device_descriptor)) != 0)
 		return 1;
 
 	if ((old_bos && !udev->bos) || (!old_bos && udev->bos))
@@ -5191,6 +5339,7 @@
 	struct usb_port *port_dev = hub->ports[port1 - 1];
 	struct usb_device *udev = port_dev->child;
 	static int unreliable_port = -1;
+	bool retry_locked;
 
 	/* Disconnect any existing devices under this port */
 	if (udev) {
@@ -5246,8 +5395,11 @@
 		unit_load = 100;
 
 	status = 0;
-	for (i = 0; i < PORT_INIT_TRIES; i++) {
 
+	for (i = 0; i < PORT_INIT_TRIES; i++) {
+		usb_lock_port(port_dev);
+		mutex_lock(hcd->address0_mutex);
+		retry_locked = true;
 		/* reallocate for each attempt, since references
 		 * to the previous one can escape in various ways
 		 */
@@ -5255,6 +5407,8 @@
 		if (!udev) {
 			dev_err(&port_dev->dev,
 					"couldn't allocate usb_device\n");
+			mutex_unlock(hcd->address0_mutex);
+			usb_unlock_port(port_dev);
 			goto done;
 		}
 
@@ -5276,12 +5430,14 @@
 		}
 
 		/* reset (non-USB 3.0 devices) and get descriptor */
-		usb_lock_port(port_dev);
-		status = hub_port_init(hub, udev, port1, i);
-		usb_unlock_port(port_dev);
+		status = hub_port_init(hub, udev, port1, i, NULL);
 		if (status < 0)
 			goto loop;
 
+		mutex_unlock(hcd->address0_mutex);
+		usb_unlock_port(port_dev);
+		retry_locked = false;
+
 		if (udev->quirks & USB_QUIRK_DELAY_INIT)
 			msleep(2000);
 
@@ -5374,6 +5530,10 @@
 		usb_ep0_reinit(udev);
 		release_devnum(udev);
 		hub_free_dev(udev);
+		if (retry_locked) {
+			mutex_unlock(hcd->address0_mutex);
+			usb_unlock_port(port_dev);
+		}
 		usb_put_dev(udev);
 		if ((status == -ENOTCONN) || (status == -ENOTSUPP))
 			break;
@@ -5381,10 +5541,7 @@
 		/* When halfway through our retry count, power-cycle the port */
 		if (i == (PORT_INIT_TRIES - 1) / 2) {
 			dev_info(&port_dev->dev, "attempt power cycle\n");
-			usb_hub_set_port_power(hdev, hub, port1, false);
-			msleep(2 * hub_power_on_good_delay(hub));
-			usb_hub_set_port_power(hdev, hub, port1, true);
-			msleep(hub_power_on_good_delay(hub));
+			hub_port_power_cycle(hub, port1);
 		}
 	}
 	if (hub->hdev->parent ||
@@ -5417,9 +5574,8 @@
 {
 	struct usb_port *port_dev = hub->ports[port1 - 1];
 	struct usb_device *udev = port_dev->child;
-	struct usb_device_descriptor descriptor;
+	struct usb_device_descriptor *descr;
 	int status = -ENODEV;
-	int retval;
 
 	dev_dbg(&port_dev->dev, "status %04x, change %04x, %s\n", portstatus,
 			portchange, portspeed(hub, portstatus));
@@ -5446,23 +5602,20 @@
 			 * changed device descriptors before resuscitating the
 			 * device.
 			 */
-			descriptor = udev->descriptor;
-			retval = usb_get_device_descriptor(udev,
-					sizeof(udev->descriptor));
-			if (retval < 0) {
+			descr = usb_get_device_descriptor(udev);
+			if (IS_ERR(descr)) {
 				dev_dbg(&udev->dev,
-						"can't read device descriptor %d\n",
-						retval);
+						"can't read device descriptor %ld\n",
+						PTR_ERR(descr));
 			} else {
-				if (descriptors_changed(udev, &descriptor,
+				if (descriptors_changed(udev, descr,
 						udev->bos)) {
 					dev_dbg(&udev->dev,
 							"device descriptor has changed\n");
-					/* for disconnect() calls */
-					udev->descriptor = descriptor;
 				} else {
 					status = 0; /* Nothing to do */
 				}
+				kfree(descr);
 			}
 #ifdef CONFIG_PM
 		} else if (udev->state == USB_STATE_SUSPENDED &&
@@ -5756,7 +5909,7 @@
 
 	/* Balance the stuff in kick_hub_wq() and allow autosuspend */
 	usb_autopm_put_interface(intf);
-	kref_put(&hub->kref, hub_release);
+	hub_put(hub);
 
 	kcov_remote_stop();
 }
@@ -5779,6 +5932,16 @@
       .idVendor = USB_VENDOR_GENESYS_LOGIC,
       .bInterfaceClass = USB_CLASS_HUB,
       .driver_info = HUB_QUIRK_CHECK_PORT_AUTOSUSPEND},
+    { .match_flags = USB_DEVICE_ID_MATCH_VENDOR
+			| USB_DEVICE_ID_MATCH_PRODUCT,
+      .idVendor = USB_VENDOR_TEXAS_INSTRUMENTS,
+      .idProduct = USB_PRODUCT_TUSB8041_USB2,
+      .driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND},
+    { .match_flags = USB_DEVICE_ID_MATCH_VENDOR
+			| USB_DEVICE_ID_MATCH_PRODUCT,
+      .idVendor = USB_VENDOR_TEXAS_INSTRUMENTS,
+      .idProduct = USB_PRODUCT_TUSB8041_USB3,
+      .driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND},
     { .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS,
       .bDeviceClass = USB_CLASS_HUB},
     { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS,
@@ -5842,6 +6005,36 @@
 } /* usb_hub_cleanup() */
 
 /**
+ * hub_hc_release_resources - clear resources used by host controller
+ * @udev: pointer to device being released
+ *
+ * Context: task context, might sleep
+ *
+ * Function releases the host controller resources in correct order before
+ * making any operation on resuming usb device. The host controller resources
+ * allocated for devices in tree should be released starting from the last
+ * usb device in tree toward the root hub. This function is used only during
+ * resuming device when usb device require reinitialization – that is, when
+ * flag udev->reset_resume is set.
+ *
+ * This call is synchronous, and may not be used in an interrupt context.
+ */
+static void hub_hc_release_resources(struct usb_device *udev)
+{
+	struct usb_hub *hub = usb_hub_to_struct_hub(udev);
+	struct usb_hcd *hcd = bus_to_hcd(udev->bus);
+	int i;
+
+	/* Release up resources for all children before this device */
+	for (i = 0; i < udev->maxchild; i++)
+		if (hub->ports[i]->child)
+			hub_hc_release_resources(hub->ports[i]->child);
+
+	if (hcd->driver->reset_device)
+		hcd->driver->reset_device(hcd, udev);
+}
+
+/**
  * usb_reset_and_verify_device - perform a USB port reset to reinitialize a device
  * @udev: device to reset (not in SUSPENDED or NOTATTACHED state)
  *
@@ -5880,7 +6073,7 @@
 	struct usb_device		*parent_hdev = udev->parent;
 	struct usb_hub			*parent_hub;
 	struct usb_hcd			*hcd = bus_to_hcd(udev->bus);
-	struct usb_device_descriptor	descriptor = udev->descriptor;
+	struct usb_device_descriptor	descriptor;
 	struct usb_host_bos		*bos;
 	int				i, j, ret = 0;
 	int				port1 = udev->portnum;
@@ -5915,15 +6108,21 @@
 	bos = udev->bos;
 	udev->bos = NULL;
 
+	if (udev->reset_resume)
+		hub_hc_release_resources(udev);
+
+	mutex_lock(hcd->address0_mutex);
+
 	for (i = 0; i < PORT_INIT_TRIES; ++i) {
 
 		/* ep0 maxpacket size may change; let the HCD know about it.
 		 * Other endpoints will be handled by re-enumeration. */
 		usb_ep0_reinit(udev);
-		ret = hub_port_init(parent_hub, udev, port1, i);
+		ret = hub_port_init(parent_hub, udev, port1, i, &descriptor);
 		if (ret >= 0 || ret == -ENOTCONN || ret == -ENODEV)
 			break;
 	}
+	mutex_unlock(hcd->address0_mutex);
 
 	if (ret < 0)
 		goto re_enumerate;
@@ -5931,7 +6130,6 @@
 	/* Device might have changed firmware (DFU or similar) */
 	if (descriptors_changed(udev, &descriptor, bos)) {
 		dev_info(&udev->dev, "device firmware changed\n");
-		udev->descriptor = descriptor;	/* for disconnect() calls */
 		goto re_enumerate;
 	}
 
@@ -6028,6 +6226,11 @@
  * the reset is over (using their post_reset method).
  *
  * Return: The same as for usb_reset_and_verify_device().
+ * However, if a reset is already in progress (for instance, if a
+ * driver doesn't have pre_reset() or post_reset() callbacks, and while
+ * being unbound or re-bound during the ongoing reset its disconnect()
+ * or probe() routine tries to perform a second, nested reset), the
+ * routine returns -EINPROGRESS.
  *
  * Note:
  * The caller must own the device lock.  For example, it's safe to use
@@ -6061,6 +6264,10 @@
 		return -EISDIR;
 	}
 
+	if (udev->reset_in_progress)
+		return -EINPROGRESS;
+	udev->reset_in_progress = 1;
+
 	port_dev = hub->ports[udev->portnum - 1];
 
 	/*
@@ -6125,6 +6332,7 @@
 
 	usb_autosuspend_device(udev);
 	memalloc_noio_restore(noio_flag);
+	udev->reset_in_progress = 0;
 	return ret;
 }
 EXPORT_SYMBOL_GPL(usb_reset_device);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/hub.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/hub.h
@@ -114,9 +114,10 @@
 		int port1);
 extern void usb_hub_remove_port_device(struct usb_hub *hub,
 		int port1);
-extern int usb_hub_set_port_power(struct usb_device *hdev, struct usb_hub *hub,
-		int port1, bool set);
+extern int usb_hub_set_port_power(struct usb_hub *hub, int port1, bool set);
 extern struct usb_hub *usb_hub_to_struct_hub(struct usb_device *hdev);
+extern void hub_get(struct usb_hub *hub);
+extern void hub_put(struct usb_hub *hub);
 extern int hub_port_debounce(struct usb_hub *hub, int port1,
 		bool must_be_connected);
 extern int usb_clear_port_feature(struct usb_device *hdev,
@@ -141,17 +142,15 @@
 {
 	return (hdev->descriptor.bDeviceProtocol == USB_HUB_PR_SS &&
 		le16_to_cpu(hdev->descriptor.bcdUSB) >= 0x0310 &&
-		hdev->bos->ssp_cap);
+		hdev->bos && hdev->bos->ssp_cap);
 }
 
 static inline unsigned hub_power_on_good_delay(struct usb_hub *hub)
 {
 	unsigned delay = hub->descriptor->bPwrOn2PwrGood * 2;
 
-	if (!hub->hdev->parent)	/* root hub */
-		return delay;
-	else /* Wait at least 100 msec for power to become stable */
-		return max(delay, 100U);
+	/* Wait at least 100 msec for power to become stable */
+	return max(delay, 100U);
 }
 
 static inline int hub_port_debounce_be_connected(struct usb_hub *hub,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/message.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/message.c
@@ -1039,40 +1039,35 @@
 }
 
 /*
- * usb_get_device_descriptor - (re)reads the device descriptor (usbcore)
- * @dev: the device whose device descriptor is being updated
- * @size: how much of the descriptor to read
+ * usb_get_device_descriptor - read the device descriptor
+ * @udev: the device whose device descriptor should be read
  *
  * Context: task context, might sleep.
  *
- * Updates the copy of the device descriptor stored in the device structure,
- * which dedicates space for this purpose.
- *
  * Not exported, only for use by the core.  If drivers really want to read
  * the device descriptor directly, they can call usb_get_descriptor() with
  * type = USB_DT_DEVICE and index = 0.
  *
- * This call is synchronous, and may not be used in an interrupt context.
- *
- * Return: The number of bytes received on success, or else the status code
- * returned by the underlying usb_control_msg() call.
+ * Returns: a pointer to a dynamically allocated usb_device_descriptor
+ * structure (which the caller must deallocate), or an ERR_PTR value.
  */
-int usb_get_device_descriptor(struct usb_device *dev, unsigned int size)
+struct usb_device_descriptor *usb_get_device_descriptor(struct usb_device *udev)
 {
 	struct usb_device_descriptor *desc;
 	int ret;
 
-	if (size > sizeof(*desc))
-		return -EINVAL;
 	desc = kmalloc(sizeof(*desc), GFP_NOIO);
 	if (!desc)
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
+
+	ret = usb_get_descriptor(udev, USB_DT_DEVICE, 0, desc, sizeof(*desc));
+	if (ret == sizeof(*desc))
+		return desc;
 
-	ret = usb_get_descriptor(dev, USB_DT_DEVICE, 0, desc, size);
 	if (ret >= 0)
-		memcpy(&dev->descriptor, desc, size);
+		ret = -EMSGSIZE;
 	kfree(desc);
-	return ret;
+	return ERR_PTR(ret);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/port.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/port.c
@@ -217,7 +217,7 @@
 	if (retval < 0)
 		return retval;
 
-	retval = usb_hub_set_port_power(hdev, hub, port1, true);
+	retval = usb_hub_set_port_power(hub, port1, true);
 	msleep(hub_power_on_good_delay(hub));
 	if (udev && !retval) {
 		/*
@@ -273,7 +273,7 @@
 	if (retval < 0)
 		return retval;
 
-	retval = usb_hub_set_port_power(hdev, hub, port1, false);
+	retval = usb_hub_set_port_power(hub, port1, false);
 	usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_CONNECTION);
 	if (!port_dev->is_superspeed)
 		usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_ENABLE);
@@ -294,9 +294,12 @@
 static void usb_port_shutdown(struct device *dev)
 {
 	struct usb_port *port_dev = to_usb_port(dev);
+	struct usb_device *udev = port_dev->child;
 
-	if (port_dev->child)
-		usb_disable_usb2_hardware_lpm(port_dev->child);
+	if (udev && !udev->port_is_suspended) {
+		usb_disable_usb2_hardware_lpm(udev);
+		usb_unlocked_disable_lpm(udev);
+	}
 }
 
 static const struct dev_pm_ops usb_port_pm_ops = {
@@ -450,7 +453,7 @@
 	struct usb_hub *peer_hub = usb_hub_to_struct_hub(peer_hdev);
 	struct usb_device *hdev = to_usb_device(port_dev->dev.parent->parent);
 
-	if (!peer_hub)
+	if (!peer_hub || port_dev->connect_type == USB_PORT_NOT_USED)
 		return 0;
 
 	hcd = bus_to_hcd(hdev->bus);
@@ -461,7 +464,8 @@
 
 	for (port1 = 1; port1 <= peer_hdev->maxchild; port1++) {
 		peer = peer_hub->ports[port1 - 1];
-		if (peer && peer->location == port_dev->location) {
+		if (peer && peer->connect_type != USB_PORT_NOT_USED &&
+		    peer->location == port_dev->location) {
 			link_peers_report(port_dev, peer);
 			return 1; /* done */
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/quirks.c
@@ -338,6 +338,10 @@
 	{ USB_DEVICE(0x0638, 0x0a13), .driver_info =
 	  USB_QUIRK_STRING_FETCH_255 },
 
+	/* Prolific Single-LUN Mass Storage Card Reader */
+	{ USB_DEVICE(0x067b, 0x2731), .driver_info = USB_QUIRK_DELAY_INIT |
+	  USB_QUIRK_NO_LPM },
+
 	/* Saitek Cyborg Gold Joystick */
 	{ USB_DEVICE(0x06a3, 0x0006), .driver_info =
 			USB_QUIRK_CONFIG_INTF_STRINGS },
@@ -362,6 +366,9 @@
 	{ USB_DEVICE(0x0781, 0x5583), .driver_info = USB_QUIRK_NO_LPM },
 	{ USB_DEVICE(0x0781, 0x5591), .driver_info = USB_QUIRK_NO_LPM },
 
+	/* Realforce 87U Keyboard */
+	{ USB_DEVICE(0x0853, 0x011b), .driver_info = USB_QUIRK_NO_LPM },
+
 	/* M-Systems Flash Disk Pioneers */
 	{ USB_DEVICE(0x08ec, 0x1000), .driver_info = USB_QUIRK_RESET_RESUME },
 
@@ -388,6 +395,15 @@
 	/* Kingston DataTraveler 3.0 */
 	{ USB_DEVICE(0x0951, 0x1666), .driver_info = USB_QUIRK_NO_LPM },
 
+	/* NVIDIA Jetson devices in Force Recovery mode */
+	{ USB_DEVICE(0x0955, 0x7018), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x0955, 0x7019), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x0955, 0x7418), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x0955, 0x7721), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x0955, 0x7c18), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x0955, 0x7e19), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x0955, 0x7f21), .driver_info = USB_QUIRK_RESET_RESUME },
+
 	/* X-Rite/Gretag-Macbeth Eye-One Pro display colorimeter */
 	{ USB_DEVICE(0x0971, 0x2000), .driver_info = USB_QUIRK_NO_SET_INTF },
 
@@ -404,6 +420,9 @@
 	{ USB_DEVICE(0x0b05, 0x17e0), .driver_info =
 			USB_QUIRK_IGNORE_REMOTE_WAKEUP },
 
+	/* Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader)*/
+	{ USB_DEVICE(0x0bda, 0x0151), .driver_info = USB_QUIRK_CONFIG_INTF_STRINGS },
+
 	/* Realtek hub in Dell WD19 (Type-C) */
 	{ USB_DEVICE(0x0bda, 0x0487), .driver_info = USB_QUIRK_NO_LPM },
 
@@ -414,6 +433,9 @@
 	{ USB_DEVICE(0x0c45, 0x7056), .driver_info =
 			USB_QUIRK_IGNORE_REMOTE_WAKEUP },
 
+	/* Sony Xperia XZ1 Compact (lilac) smartphone in fastboot mode */
+	{ USB_DEVICE(0x0fce, 0x0dde), .driver_info = USB_QUIRK_NO_LPM },
+
 	/* Action Semiconductor flash disk */
 	{ USB_DEVICE(0x10d6, 0x2200), .driver_info =
 			USB_QUIRK_STRING_FETCH_255 },
@@ -421,6 +443,10 @@
 	/* novation SoundControl XL */
 	{ USB_DEVICE(0x1235, 0x0061), .driver_info = USB_QUIRK_RESET_RESUME },
 
+	/* Focusrite Scarlett Solo USB */
+	{ USB_DEVICE(0x1235, 0x8211), .driver_info =
+			USB_QUIRK_DISCONNECT_SUSPEND },
+
 	/* Huawei 4G LTE module */
 	{ USB_DEVICE(0x12d1, 0x15bb), .driver_info =
 			USB_QUIRK_DISCONNECT_SUSPEND },
@@ -434,6 +460,16 @@
 	{ USB_DEVICE(0x1532, 0x0116), .driver_info =
 			USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL },
 
+	/* Lenovo ThinkPad OneLink+ Dock twin hub controllers (VIA Labs VL812) */
+	{ USB_DEVICE(0x17ef, 0x1018), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x17ef, 0x1019), .driver_info = USB_QUIRK_RESET_RESUME },
+
+	/* Lenovo USB-C to Ethernet Adapter RTL8153-04 */
+	{ USB_DEVICE(0x17ef, 0x720c), .driver_info = USB_QUIRK_NO_LPM },
+
+	/* Lenovo Powered USB-C Travel Hub (4X90S92381, RTL8153 GigE) */
+	{ USB_DEVICE(0x17ef, 0x721e), .driver_info = USB_QUIRK_NO_LPM },
+
 	/* Lenovo ThinkCenter A630Z TI024Gen3 usb-audio */
 	{ USB_DEVICE(0x17ef, 0xa012), .driver_info =
 			USB_QUIRK_DISCONNECT_SUSPEND },
@@ -474,6 +510,9 @@
 	{ USB_DEVICE(0x1b1c, 0x1b38), .driver_info = USB_QUIRK_DELAY_INIT |
 	  USB_QUIRK_DELAY_CTRL_MSG },
 
+	/* START BP-850k Printer */
+	{ USB_DEVICE(0x1bc3, 0x0003), .driver_info = USB_QUIRK_NO_SET_INTF },
+
 	/* MIDI keyboard WORLDE MINI */
 	{ USB_DEVICE(0x1c75, 0x0204), .driver_info =
 			USB_QUIRK_CONFIG_INTF_STRINGS },
@@ -487,6 +526,9 @@
 	/* Blackmagic Design UltraStudio SDI */
 	{ USB_DEVICE(0x1edb, 0xbd4f), .driver_info = USB_QUIRK_NO_LPM },
 
+	/* Teclast disk */
+	{ USB_DEVICE(0x1f75, 0x0917), .driver_info = USB_QUIRK_NO_LPM },
+
 	/* Hauppauge HVR-950q */
 	{ USB_DEVICE(0x2040, 0x7200), .driver_info =
 			USB_QUIRK_CONFIG_INTF_STRINGS },
@@ -501,6 +543,15 @@
 	/* DJI CineSSD */
 	{ USB_DEVICE(0x2ca3, 0x0031), .driver_info = USB_QUIRK_NO_LPM },
 
+	/* Alcor Link AK9563 SC Reader used in 2022 Lenovo ThinkPads */
+	{ USB_DEVICE(0x2ce3, 0x9563), .driver_info = USB_QUIRK_NO_LPM },
+
+	/* DELL USB GEN2 */
+	{ USB_DEVICE(0x413c, 0xb062), .driver_info = USB_QUIRK_NO_LPM | USB_QUIRK_RESET_RESUME },
+
+	/* VCOM device */
+	{ USB_DEVICE(0x4296, 0x7570), .driver_info = USB_QUIRK_CONFIG_INTF_STRINGS },
+
 	/* INTEL VALUE SSD */
 	{ USB_DEVICE(0x8086, 0xf1a5), .driver_info = USB_QUIRK_RESET_RESUME },
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/sysfs.c
@@ -670,6 +670,7 @@
 
 static void remove_power_attributes(struct device *dev)
 {
+	sysfs_unmerge_group(&dev->kobj, &usb3_hardware_lpm_attr_group);
 	sysfs_unmerge_group(&dev->kobj, &usb2_hardware_lpm_attr_group);
 	sysfs_unmerge_group(&dev->kobj, &power_attr_group);
 }
@@ -868,11 +869,7 @@
 	size_t srclen, n;
 	int cfgno;
 	void *src;
-	int retval;
 
-	retval = usb_lock_device_interruptible(udev);
-	if (retval < 0)
-		return -EINTR;
 	/* The binary attribute begins with the device descriptor.
 	 * Following that are the raw descriptor entries for all the
 	 * configurations (config plus subsidiary descriptors).
@@ -897,7 +894,6 @@
 			off -= srclen;
 		}
 	}
-	usb_unlock_device(udev);
 	return count - nleft;
 }
 
@@ -1174,14 +1170,24 @@
 {
 	struct usb_interface *intf = to_usb_interface(dev);
 	bool val;
+	struct kernfs_node *kn;
 
 	if (strtobool(buf, &val) != 0)
 		return -EINVAL;
 
-	if (val)
+	if (val) {
 		usb_authorize_interface(intf);
-	else
-		usb_deauthorize_interface(intf);
+	} else {
+		/*
+		 * Prevent deadlock if another process is concurrently
+		 * trying to unregister intf.
+		 */
+		kn = sysfs_break_active_protection(&dev->kobj, &attr->attr);
+		if (kn) {
+			usb_deauthorize_interface(intf);
+			sysfs_unbreak_active_protection(kn);
+		}
+	}
 
 	return count;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/urb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/urb.c
@@ -715,6 +715,12 @@
 	if (!(urb && urb->dev && urb->ep))
 		return;
 	atomic_inc(&urb->reject);
+	/*
+	 * Order the write of urb->reject above before the read
+	 * of urb->use_count below.  Pairs with the barriers in
+	 * __usb_hcd_giveback_urb() and usb_hcd_submit_urb().
+	 */
+	smp_mb__after_atomic();
 
 	usb_hcd_unlink_urb(urb, -ENOENT);
 	wait_event(usb_kill_urb_queue, atomic_read(&urb->use_count) == 0);
@@ -756,6 +762,12 @@
 	if (!urb)
 		return;
 	atomic_inc(&urb->reject);
+	/*
+	 * Order the write of urb->reject above before the read
+	 * of urb->use_count below.  Pairs with the barriers in
+	 * __usb_hcd_giveback_urb() and usb_hcd_submit_urb().
+	 */
+	smp_mb__after_atomic();
 
 	if (!urb->dev || !urb->ep)
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/usb-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/usb-acpi.c
@@ -37,6 +37,71 @@
 }
 EXPORT_SYMBOL_GPL(usb_acpi_power_manageable);
 
+#define UUID_USB_CONTROLLER_DSM "ce2ee385-00e6-48cb-9f05-2edb927c4899"
+#define USB_DSM_DISABLE_U1_U2_FOR_PORT	5
+
+/**
+ * usb_acpi_port_lpm_incapable - check if lpm should be disabled for a port.
+ * @hdev: USB device belonging to the usb hub
+ * @index: zero based port index
+ *
+ * Some USB3 ports may not support USB3 link power management U1/U2 states
+ * due to different retimer setup. ACPI provides _DSM method which returns 0x01
+ * if U1 and U2 states should be disabled. Evaluate _DSM with:
+ * Arg0: UUID = ce2ee385-00e6-48cb-9f05-2edb927c4899
+ * Arg1: Revision ID = 0
+ * Arg2: Function Index = 5
+ * Arg3: (empty)
+ *
+ * Return 1 if USB3 port is LPM incapable, negative on error, otherwise 0
+ */
+
+int usb_acpi_port_lpm_incapable(struct usb_device *hdev, int index)
+{
+	union acpi_object *obj;
+	acpi_handle port_handle;
+	int port1 = index + 1;
+	guid_t guid;
+	int ret;
+
+	ret = guid_parse(UUID_USB_CONTROLLER_DSM, &guid);
+	if (ret)
+		return ret;
+
+	port_handle = usb_get_hub_port_acpi_handle(hdev, port1);
+	if (!port_handle) {
+		dev_dbg(&hdev->dev, "port-%d no acpi handle\n", port1);
+		return -ENODEV;
+	}
+
+	if (!acpi_check_dsm(port_handle, &guid, 0,
+			    BIT(USB_DSM_DISABLE_U1_U2_FOR_PORT))) {
+		dev_dbg(&hdev->dev, "port-%d no _DSM function %d\n",
+			port1, USB_DSM_DISABLE_U1_U2_FOR_PORT);
+		return -ENODEV;
+	}
+
+	obj = acpi_evaluate_dsm(port_handle, &guid, 0,
+				USB_DSM_DISABLE_U1_U2_FOR_PORT, NULL);
+
+	if (!obj)
+		return -ENODEV;
+
+	if (obj->type != ACPI_TYPE_INTEGER) {
+		dev_dbg(&hdev->dev, "evaluate port-%d _DSM failed\n", port1);
+		ACPI_FREE(obj);
+		return -EINVAL;
+	}
+
+	if (obj->integer.value == 0x01)
+		ret = 1;
+
+	ACPI_FREE(obj);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(usb_acpi_port_lpm_incapable);
+
 /**
  * usb_acpi_set_power_state - control usb port's power via acpi power
  * resource
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/usb.c
@@ -207,6 +207,82 @@
 EXPORT_SYMBOL_GPL(usb_find_common_endpoints_reverse);
 
 /**
+ * usb_find_endpoint() - Given an endpoint address, search for the endpoint's
+ * usb_host_endpoint structure in an interface's current altsetting.
+ * @intf: the interface whose current altsetting should be searched
+ * @ep_addr: the endpoint address (number and direction) to find
+ *
+ * Search the altsetting's list of endpoints for one with the specified address.
+ *
+ * Return: Pointer to the usb_host_endpoint if found, %NULL otherwise.
+ */
+static const struct usb_host_endpoint *usb_find_endpoint(
+		const struct usb_interface *intf, unsigned int ep_addr)
+{
+	int n;
+	const struct usb_host_endpoint *ep;
+
+	n = intf->cur_altsetting->desc.bNumEndpoints;
+	ep = intf->cur_altsetting->endpoint;
+	for (; n > 0; (--n, ++ep)) {
+		if (ep->desc.bEndpointAddress == ep_addr)
+			return ep;
+	}
+	return NULL;
+}
+
+/**
+ * usb_check_bulk_endpoints - Check whether an interface's current altsetting
+ * contains a set of bulk endpoints with the given addresses.
+ * @intf: the interface whose current altsetting should be searched
+ * @ep_addrs: 0-terminated array of the endpoint addresses (number and
+ * direction) to look for
+ *
+ * Search for endpoints with the specified addresses and check their types.
+ *
+ * Return: %true if all the endpoints are found and are bulk, %false otherwise.
+ */
+bool usb_check_bulk_endpoints(
+		const struct usb_interface *intf, const u8 *ep_addrs)
+{
+	const struct usb_host_endpoint *ep;
+
+	for (; *ep_addrs; ++ep_addrs) {
+		ep = usb_find_endpoint(intf, *ep_addrs);
+		if (!ep || !usb_endpoint_xfer_bulk(&ep->desc))
+			return false;
+	}
+	return true;
+}
+EXPORT_SYMBOL_GPL(usb_check_bulk_endpoints);
+
+/**
+ * usb_check_int_endpoints - Check whether an interface's current altsetting
+ * contains a set of interrupt endpoints with the given addresses.
+ * @intf: the interface whose current altsetting should be searched
+ * @ep_addrs: 0-terminated array of the endpoint addresses (number and
+ * direction) to look for
+ *
+ * Search for endpoints with the specified addresses and check their types.
+ *
+ * Return: %true if all the endpoints are found and are interrupt,
+ * %false otherwise.
+ */
+bool usb_check_int_endpoints(
+		const struct usb_interface *intf, const u8 *ep_addrs)
+{
+	const struct usb_host_endpoint *ep;
+
+	for (; *ep_addrs; ++ep_addrs) {
+		ep = usb_find_endpoint(intf, *ep_addrs);
+		if (!ep || !usb_endpoint_xfer_int(&ep->desc))
+			return false;
+	}
+	return true;
+}
+EXPORT_SYMBOL_GPL(usb_check_int_endpoints);
+
+/**
  * usb_find_alt_setting() - Given a configuration, find the alternate setting
  * for the given interface.
  * @config: the configuration to search (not necessarily the current config).
@@ -1036,7 +1112,7 @@
 
 static void usb_debugfs_cleanup(void)
 {
-	debugfs_remove(debugfs_lookup("devices", usb_debug_root));
+	debugfs_lookup_and_remove("devices", usb_debug_root);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/core/usb.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/core/usb.h
@@ -42,8 +42,8 @@
 		struct usb_endpoint_descriptor *epd);
 extern int usb_remove_device(struct usb_device *udev);
 
-extern int usb_get_device_descriptor(struct usb_device *dev,
-		unsigned int size);
+extern struct usb_device_descriptor *usb_get_device_descriptor(
+		struct usb_device *udev);
 extern int usb_set_isoch_delay(struct usb_device *dev);
 extern int usb_get_bos_descriptor(struct usb_device *dev);
 extern void usb_release_bos_descriptor(struct usb_device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/core.h
@@ -755,8 +755,14 @@
  * struct dwc2_hregs_backup - Holds host registers state before
  * entering partial power down
  * @hcfg:		Backup of HCFG register
+ * @hflbaddr:		Backup of HFLBADDR register
  * @haintmsk:		Backup of HAINTMSK register
+ * @hcchar:		Backup of HCCHAR register
+ * @hcsplt:		Backup of HCSPLT register
  * @hcintmsk:		Backup of HCINTMSK register
+ * @hctsiz:		Backup of HCTSIZ register
+ * @hdma:		Backup of HCDMA register
+ * @hcdmab:		Backup of HCDMAB register
  * @hprt0:		Backup of HPTR0 register
  * @hfir:		Backup of HFIR register
  * @hptxfsiz:		Backup of HPTXFSIZ register
@@ -764,8 +770,14 @@
  */
 struct dwc2_hregs_backup {
 	u32 hcfg;
+	u32 hflbaddr;
 	u32 haintmsk;
+	u32 hcchar[MAX_EPS_CHANNELS];
+	u32 hcsplt[MAX_EPS_CHANNELS];
 	u32 hcintmsk[MAX_EPS_CHANNELS];
+	u32 hctsiz[MAX_EPS_CHANNELS];
+	u32 hcidma[MAX_EPS_CHANNELS];
+	u32 hcidmab[MAX_EPS_CHANNELS];
 	u32 hprt0;
 	u32 hfir;
 	u32 hptxfsiz;
@@ -1107,6 +1119,7 @@
 	bool needs_byte_swap;
 
 	/* DWC OTG HW Release versions */
+#define DWC2_CORE_REV_4_30a	0x4f54430a
 #define DWC2_CORE_REV_2_71a	0x4f54271a
 #define DWC2_CORE_REV_2_72a     0x4f54272a
 #define DWC2_CORE_REV_2_80a	0x4f54280a
@@ -1345,6 +1358,7 @@
 int dwc2_restore_global_registers(struct dwc2_hsotg *hsotg);
 
 void dwc2_enable_acg(struct dwc2_hsotg *hsotg);
+void dwc2_wakeup_from_lpm_l1(struct dwc2_hsotg *hsotg, bool remotewakeup);
 
 /* This function should be called on every hardware interrupt. */
 irqreturn_t dwc2_handle_common_intr(int irq, void *dev);
@@ -1417,6 +1431,7 @@
 void dwc2_hsotg_disconnect(struct dwc2_hsotg *dwc2);
 int dwc2_hsotg_set_test_mode(struct dwc2_hsotg *hsotg, int testmode);
 #define dwc2_is_device_connected(hsotg) (hsotg->connected)
+#define dwc2_is_device_enabled(hsotg) (hsotg->enabled)
 int dwc2_backup_device_registers(struct dwc2_hsotg *hsotg);
 int dwc2_restore_device_registers(struct dwc2_hsotg *hsotg, int remote_wakeup);
 int dwc2_gadget_enter_hibernation(struct dwc2_hsotg *hsotg);
@@ -1453,6 +1468,7 @@
 					   int testmode)
 { return 0; }
 #define dwc2_is_device_connected(hsotg) (0)
+#define dwc2_is_device_enabled(hsotg) (0)
 static inline int dwc2_backup_device_registers(struct dwc2_hsotg *hsotg)
 { return 0; }
 static inline int dwc2_restore_device_registers(struct dwc2_hsotg *hsotg,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/core_intr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/core_intr.c
@@ -327,7 +327,8 @@
 
 			/* Exit gadget mode clock gating. */
 			if (hsotg->params.power_down ==
-			    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended)
+			    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended &&
+			    !hsotg->params.no_clock_gating)
 				dwc2_gadget_exit_clock_gating(hsotg, 0);
 		}
 
@@ -352,10 +353,11 @@
  * @hsotg: Programming view of DWC_otg controller
  *
  */
-static void dwc2_wakeup_from_lpm_l1(struct dwc2_hsotg *hsotg)
+void dwc2_wakeup_from_lpm_l1(struct dwc2_hsotg *hsotg, bool remotewakeup)
 {
 	u32 glpmcfg;
-	u32 i = 0;
+	u32 pcgctl;
+	u32 dctl;
 
 	if (hsotg->lx_state != DWC2_L1) {
 		dev_err(hsotg->dev, "Core isn't in DWC2_L1 state\n");
@@ -364,37 +366,57 @@
 
 	glpmcfg = dwc2_readl(hsotg, GLPMCFG);
 	if (dwc2_is_device_mode(hsotg)) {
-		dev_dbg(hsotg->dev, "Exit from L1 state\n");
+		dev_dbg(hsotg->dev, "Exit from L1 state, remotewakeup=%d\n", remotewakeup);
 		glpmcfg &= ~GLPMCFG_ENBLSLPM;
-		glpmcfg &= ~GLPMCFG_HIRD_THRES_EN;
+		glpmcfg &= ~GLPMCFG_HIRD_THRES_MASK;
 		dwc2_writel(hsotg, glpmcfg, GLPMCFG);
 
-		do {
-			glpmcfg = dwc2_readl(hsotg, GLPMCFG);
+		pcgctl = dwc2_readl(hsotg, PCGCTL);
+		pcgctl &= ~PCGCTL_ENBL_SLEEP_GATING;
+		dwc2_writel(hsotg, pcgctl, PCGCTL);
+
+		glpmcfg = dwc2_readl(hsotg, GLPMCFG);
+		if (glpmcfg & GLPMCFG_ENBESL) {
+			glpmcfg |= GLPMCFG_RSTRSLPSTS;
+			dwc2_writel(hsotg, glpmcfg, GLPMCFG);
+		}
 
-			if (!(glpmcfg & (GLPMCFG_COREL1RES_MASK |
-					 GLPMCFG_L1RESUMEOK | GLPMCFG_SLPSTS)))
-				break;
+		if (remotewakeup) {
+			if (dwc2_hsotg_wait_bit_set(hsotg, GLPMCFG, GLPMCFG_L1RESUMEOK, 1000)) {
+				dev_warn(hsotg->dev, "%s: timeout GLPMCFG_L1RESUMEOK\n", __func__);
+				goto fail;
+				return;
+			}
 
-			udelay(1);
-		} while (++i < 200);
+			dctl = dwc2_readl(hsotg, DCTL);
+			dctl |= DCTL_RMTWKUPSIG;
+			dwc2_writel(hsotg, dctl, DCTL);
+
+			if (dwc2_hsotg_wait_bit_set(hsotg, GINTSTS, GINTSTS_WKUPINT, 1000)) {
+				dev_warn(hsotg->dev, "%s: timeout GINTSTS_WKUPINT\n", __func__);
+				goto fail;
+				return;
+			}
+		}
 
-		if (i == 200) {
-			dev_err(hsotg->dev, "Failed to exit L1 sleep state in 200us.\n");
+		glpmcfg = dwc2_readl(hsotg, GLPMCFG);
+		if (glpmcfg & GLPMCFG_COREL1RES_MASK || glpmcfg & GLPMCFG_SLPSTS ||
+		    glpmcfg & GLPMCFG_L1RESUMEOK) {
+			goto fail;
 			return;
 		}
-		dwc2_gadget_init_lpm(hsotg);
+
+		/* Inform gadget to exit from L1 */
+		call_gadget(hsotg, resume);
+		/* Change to L0 state */
+		hsotg->lx_state = DWC2_L0;
+		hsotg->bus_suspended = false;
+fail:		dwc2_gadget_init_lpm(hsotg);
 	} else {
 		/* TODO */
 		dev_err(hsotg->dev, "Host side LPM is not supported.\n");
 		return;
 	}
-
-	/* Change to L0 state */
-	hsotg->lx_state = DWC2_L0;
-
-	/* Inform gadget to exit from L1 */
-	call_gadget(hsotg, resume);
 }
 
 /*
@@ -415,7 +437,7 @@
 	dev_dbg(hsotg->dev, "%s lxstate = %d\n", __func__, hsotg->lx_state);
 
 	if (hsotg->lx_state == DWC2_L1) {
-		dwc2_wakeup_from_lpm_l1(hsotg);
+		dwc2_wakeup_from_lpm_l1(hsotg, false);
 		return;
 	}
 
@@ -438,7 +460,8 @@
 
 			/* Exit gadget mode clock gating. */
 			if (hsotg->params.power_down ==
-			    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended)
+			    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended &&
+			    !hsotg->params.no_clock_gating)
 				dwc2_gadget_exit_clock_gating(hsotg, 0);
 		} else {
 			/* Change to L0 state */
@@ -455,7 +478,8 @@
 			}
 
 			if (hsotg->params.power_down ==
-			    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended)
+			    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended &&
+			    !hsotg->params.no_clock_gating)
 				dwc2_host_exit_clock_gating(hsotg, 1);
 
 			/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/drd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/drd.c
@@ -7,6 +7,7 @@
  * Author(s): Amelie Delaunay <amelie.delaunay@st.com>
  */
 
+#include <linux/clk.h>
 #include <linux/iopoll.h>
 #include <linux/platform_device.h>
 #include <linux/usb/role.h>
@@ -25,9 +26,9 @@
 	gotgctl &= ~(GOTGCTL_BVALOVAL | GOTGCTL_AVALOVAL | GOTGCTL_VBVALOVAL);
 	dwc2_writel(hsotg, gotgctl, GOTGCTL);
 
-	dwc2_force_mode(hsotg, false);
-
 	spin_unlock_irqrestore(&hsotg->lock, flags);
+
+	dwc2_force_mode(hsotg, (hsotg->dr_mode == USB_DR_MODE_HOST));
 }
 
 static int dwc2_ovr_avalid(struct dwc2_hsotg *hsotg, bool valid)
@@ -39,6 +40,7 @@
 	    (!valid && !(gotgctl & GOTGCTL_ASESVLD)))
 		return -EALREADY;
 
+	gotgctl &= ~GOTGCTL_BVALOVAL;
 	if (valid)
 		gotgctl |= GOTGCTL_AVALOVAL | GOTGCTL_VBVALOVAL;
 	else
@@ -57,6 +59,7 @@
 	    (!valid && !(gotgctl & GOTGCTL_BSESVLD)))
 		return -EALREADY;
 
+	gotgctl &= ~GOTGCTL_AVALOVAL;
 	if (valid)
 		gotgctl |= GOTGCTL_BVALOVAL | GOTGCTL_VBVALOVAL;
 	else
@@ -86,14 +89,39 @@
 	}
 #endif
 
+	/*
+	 * In case of USB_DR_MODE_PERIPHERAL, clock is disabled at the end of
+	 * the probe and enabled on udc_start.
+	 * If role-switch set is called before the udc_start, we need to enable
+	 * the clock to read/write GOTGCTL and GUSBCFG registers to override
+	 * mode and sessions. It is the case if cable is plugged at boot.
+	 */
+	if (!hsotg->ll_hw_enabled && hsotg->clk) {
+		int ret = clk_prepare_enable(hsotg->clk);
+
+		if (ret)
+			return ret;
+	}
+
 	spin_lock_irqsave(&hsotg->lock, flags);
 
+	if ((IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL) ||
+	     IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)) &&
+	     dwc2_is_device_mode(hsotg) &&
+	     hsotg->lx_state == DWC2_L2 &&
+	     hsotg->params.power_down == DWC2_POWER_DOWN_PARAM_NONE &&
+	     hsotg->bus_suspended &&
+	     !hsotg->params.no_clock_gating)
+		dwc2_gadget_exit_clock_gating(hsotg, 0);
+
 	if (role == USB_ROLE_HOST) {
 		already = dwc2_ovr_avalid(hsotg, true);
 	} else if (role == USB_ROLE_DEVICE) {
 		already = dwc2_ovr_bvalid(hsotg, true);
-		/* This clear DCTL.SFTDISCON bit */
-		dwc2_hsotg_core_connect(hsotg);
+		if (dwc2_is_device_enabled(hsotg)) {
+			/* This clear DCTL.SFTDISCON bit */
+			dwc2_hsotg_core_connect(hsotg);
+		}
 	} else {
 		if (dwc2_is_device_mode(hsotg)) {
 			if (!dwc2_ovr_bvalid(hsotg, false))
@@ -110,6 +138,9 @@
 		/* This will raise a Connector ID Status Change Interrupt */
 		dwc2_force_mode(hsotg, role == USB_ROLE_HOST);
 
+	if (!hsotg->ll_hw_enabled && hsotg->clk)
+		clk_disable_unprepare(hsotg->clk);
+
 	dev_dbg(hsotg->dev, "%s-session valid\n",
 		role == USB_ROLE_NONE ? "No" :
 		role == USB_ROLE_HOST ? "A" : "B");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/gadget.c
@@ -886,10 +886,10 @@
 	}
 
 	/* DMA sg buffer */
-	for_each_sg(ureq->sg, sg, ureq->num_sgs, i) {
+	for_each_sg(ureq->sg, sg, ureq->num_mapped_sgs, i) {
 		dwc2_gadget_fill_nonisoc_xfer_ddma_one(hs_ep, &desc,
 			sg_dma_address(sg) + sg->offset, sg_dma_len(sg),
-			sg_is_last(sg));
+			(i == (ureq->num_mapped_sgs - 1)));
 		desc_count += hs_ep->desc_count;
 	}
 
@@ -1198,6 +1198,8 @@
 			}
 			ctrl |= DXEPCTL_CNAK;
 		} else {
+			hs_req->req.frame_number = hs_ep->target_frame;
+			hs_req->req.actual = 0;
 			dwc2_hsotg_complete_request(hsotg, hs_ep, hs_req, -ENODATA);
 			return;
 		}
@@ -1414,6 +1416,10 @@
 		ep->name, req, req->length, req->buf, req->no_interrupt,
 		req->zero, req->short_not_ok);
 
+	if (hs->lx_state == DWC2_L1) {
+		dwc2_wakeup_from_lpm_l1(hs, true);
+	}
+
 	/* Prevent new request submission when controller is suspended */
 	if (hs->lx_state != DWC2_L0) {
 		dev_dbg(hs->dev, "%s: submit request only in active state\n",
@@ -2857,9 +2863,12 @@
 
 	do {
 		hs_req = get_ep_head(hs_ep);
-		if (hs_req)
+		if (hs_req) {
+			hs_req->req.frame_number = hs_ep->target_frame;
+			hs_req->req.actual = 0;
 			dwc2_hsotg_complete_request(hsotg, hs_ep, hs_req,
 						    -ENODATA);
+		}
 		dwc2_gadget_incr_frame_num(hs_ep);
 		/* Update current frame number value. */
 		hsotg->frame_number = dwc2_hsotg_read_frameno(hsotg);
@@ -2912,8 +2921,11 @@
 
 	while (dwc2_gadget_target_frame_elapsed(ep)) {
 		hs_req = get_ep_head(ep);
-		if (hs_req)
+		if (hs_req) {
+			hs_req->req.frame_number = ep->target_frame;
+			hs_req->req.actual = 0;
 			dwc2_hsotg_complete_request(hsotg, ep, hs_req, -ENODATA);
+		}
 
 		dwc2_gadget_incr_frame_num(ep);
 		/* Update current frame number value. */
@@ -3002,8 +3014,11 @@
 
 	while (dwc2_gadget_target_frame_elapsed(hs_ep)) {
 		hs_req = get_ep_head(hs_ep);
-		if (hs_req)
+		if (hs_req) {
+			hs_req->req.frame_number = hs_ep->target_frame;
+			hs_req->req.actual = 0;
 			dwc2_hsotg_complete_request(hsotg, hs_ep, hs_req, -ENODATA);
+		}
 
 		dwc2_gadget_incr_frame_num(hs_ep);
 		/* Update current frame number value. */
@@ -3583,7 +3598,8 @@
 void dwc2_hsotg_core_connect(struct dwc2_hsotg *hsotg)
 {
 	/* remove the soft-disconnect and let's go */
-	dwc2_clear_bit(hsotg, DCTL, DCTL_SFTDISCON);
+	if (!hsotg->role_sw || (dwc2_readl(hsotg, GOTGCTL) & GOTGCTL_BSESVLD))
+		dwc2_clear_bit(hsotg, DCTL, DCTL_SFTDISCON);
 }
 
 /**
@@ -3716,6 +3732,12 @@
 		if (hsotg->in_ppd && hsotg->lx_state == DWC2_L2)
 			dwc2_exit_partial_power_down(hsotg, 0, true);
 
+		/* Exit gadget mode clock gating. */
+		if (hsotg->params.power_down ==
+		    DWC2_POWER_DOWN_PARAM_NONE && hsotg->bus_suspended &&
+		    !hsotg->params.no_clock_gating)
+			dwc2_gadget_exit_clock_gating(hsotg, 0);
+
 		hsotg->lx_state = DWC2_L0;
 	}
 
@@ -4533,7 +4555,6 @@
 
 	WARN_ON(hsotg->driver);
 
-	driver->driver.bus = NULL;
 	hsotg->driver = driver;
 	hsotg->gadget.dev.of_node = hsotg->dev->of_node;
 	hsotg->gadget.speed = USB_SPEED_UNKNOWN;
@@ -4592,6 +4613,7 @@
 	spin_lock_irqsave(&hsotg->lock, flags);
 
 	hsotg->driver = NULL;
+	hsotg->gadget.dev.of_node = NULL;
 	hsotg->gadget.speed = USB_SPEED_UNKNOWN;
 	hsotg->enabled = 0;
 
@@ -4963,7 +4985,18 @@
 		hsotg->params.g_np_tx_fifo_size);
 	dev_dbg(dev, "RXFIFO size: %d\n", hsotg->params.g_rx_fifo_size);
 
-	hsotg->gadget.max_speed = USB_SPEED_HIGH;
+	switch (hsotg->params.speed) {
+	case DWC2_SPEED_PARAM_LOW:
+		hsotg->gadget.max_speed = USB_SPEED_LOW;
+		break;
+	case DWC2_SPEED_PARAM_FULL:
+		hsotg->gadget.max_speed = USB_SPEED_FULL;
+		break;
+	default:
+		hsotg->gadget.max_speed = USB_SPEED_HIGH;
+		break;
+	}
+
 	hsotg->gadget.ops = &dwc2_hsotg_gadget_ops;
 	hsotg->gadget.name = dev_name(dev);
 	hsotg->remote_wakeup_allowed = 0;
@@ -5074,7 +5107,7 @@
 		hsotg->gadget.speed = USB_SPEED_UNKNOWN;
 		spin_unlock_irqrestore(&hsotg->lock, flags);
 
-		for (ep = 0; ep < hsotg->num_of_eps; ep++) {
+		for (ep = 1; ep < hsotg->num_of_eps; ep++) {
 			if (hsotg->eps_in[ep])
 				dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
 			if (hsotg->eps_out[ep])
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/hcd.c
@@ -2734,8 +2734,11 @@
 			hsotg->available_host_channels--;
 		}
 		qh = list_entry(qh_ptr, struct dwc2_qh, qh_list_entry);
-		if (dwc2_assign_and_init_hc(hsotg, qh))
+		if (dwc2_assign_and_init_hc(hsotg, qh)) {
+			if (hsotg->params.uframe_sched)
+				hsotg->available_host_channels++;
 			break;
+		}
 
 		/*
 		 * Move the QH from the periodic ready schedule to the
@@ -2768,8 +2771,11 @@
 			hsotg->available_host_channels--;
 		}
 
-		if (dwc2_assign_and_init_hc(hsotg, qh))
+		if (dwc2_assign_and_init_hc(hsotg, qh)) {
+			if (hsotg->params.uframe_sched)
+				hsotg->available_host_channels++;
 			break;
+		}
 
 		/*
 		 * Move the QH from the non-periodic inactive schedule to the
@@ -3573,11 +3579,9 @@
 			port_status |= USB_PORT_STAT_C_OVERCURRENT << 16;
 		}
 
-		if (!hsotg->flags.b.port_connect_status) {
+		if (dwc2_is_device_mode(hsotg)) {
 			/*
-			 * The port is disconnected, which means the core is
-			 * either in device mode or it soon will be. Just
-			 * return 0's for the remainder of the port status
+			 * Just return 0's for the remainder of the port status
 			 * since the port register can't be read if the core
 			 * is in device mode.
 			 */
@@ -3647,13 +3651,11 @@
 		if (wvalue != USB_PORT_FEAT_TEST && (!windex || windex > 1))
 			goto error;
 
-		if (!hsotg->flags.b.port_connect_status) {
+		if (dwc2_is_device_mode(hsotg)) {
 			/*
-			 * The port is disconnected, which means the core is
-			 * either in device mode or it soon will be. Just
-			 * return without doing anything since the port
-			 * register can't be written if the core is in device
-			 * mode.
+			 * Just return 0's for the remainder of the port status
+			 * since the port register can't be read if the core
+			 * is in device mode.
 			 */
 			break;
 		}
@@ -4176,6 +4178,8 @@
 			 urb->actual_length);
 
 	if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
+		if (!hsotg->params.dma_desc_enable)
+			urb->start_frame = qtd->qh->start_active_frame;
 		urb->error_count = dwc2_hcd_urb_get_error_count(qtd->urb);
 		for (i = 0; i < urb->number_of_packets; ++i) {
 			urb->iso_frame_desc[i].actual_length =
@@ -4374,7 +4378,7 @@
 	if (hsotg->bus_suspended)
 		goto skip_power_saving;
 
-	if (hsotg->flags.b.port_connect_status == 0)
+	if (!(dwc2_read_hprt0(hsotg) & HPRT0_CONNSTS))
 		goto skip_power_saving;
 
 	switch (hsotg->params.power_down) {
@@ -4403,11 +4407,12 @@
 		 * If not hibernation nor partial power down are supported,
 		 * clock gating is used to save power.
 		 */
-		if (!hsotg->params.no_clock_gating)
+		if (!hsotg->params.no_clock_gating) {
 			dwc2_host_enter_clock_gating(hsotg);
 
-		/* After entering suspend, hardware is not accessible */
-		clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+			/* After entering suspend, hardware is not accessible */
+			clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+		}
 		break;
 	default:
 		goto skip_power_saving;
@@ -4455,6 +4460,7 @@
 	 * Power Down mode.
 	 */
 	if (hprt0 & HPRT0_CONNSTS) {
+		set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
 		hsotg->lx_state = DWC2_L0;
 		goto unlock;
 	}
@@ -4681,7 +4687,7 @@
 	}
 
 	if (hsotg->params.power_down == DWC2_POWER_DOWN_PARAM_NONE &&
-	    hsotg->bus_suspended) {
+	    hsotg->bus_suspended && !hsotg->params.no_clock_gating) {
 		if (dwc2_is_device_mode(hsotg))
 			dwc2_gadget_exit_clock_gating(hsotg, 0);
 		else
@@ -4801,8 +4807,8 @@
 	if (qh_allocated && qh->channel && qh->channel->qh == qh)
 		qh->channel->qh = NULL;
 fail2:
-	spin_unlock_irqrestore(&hsotg->lock, flags);
 	urb->hcpriv = NULL;
+	spin_unlock_irqrestore(&hsotg->lock, flags);
 	kfree(qtd);
 fail1:
 	if (qh_allocated) {
@@ -5193,7 +5199,7 @@
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		retval = -EINVAL;
-		goto error1;
+		goto error2;
 	}
 	hcd->rsrc_start = res->start;
 	hcd->rsrc_len = resource_size(res);
@@ -5436,9 +5442,16 @@
 	/* Backup Host regs */
 	hr = &hsotg->hr_backup;
 	hr->hcfg = dwc2_readl(hsotg, HCFG);
+	hr->hflbaddr = dwc2_readl(hsotg, HFLBADDR);
 	hr->haintmsk = dwc2_readl(hsotg, HAINTMSK);
-	for (i = 0; i < hsotg->params.host_channels; ++i)
+	for (i = 0; i < hsotg->params.host_channels; ++i) {
+		hr->hcchar[i] = dwc2_readl(hsotg, HCCHAR(i));
+		hr->hcsplt[i] = dwc2_readl(hsotg, HCSPLT(i));
 		hr->hcintmsk[i] = dwc2_readl(hsotg, HCINTMSK(i));
+		hr->hctsiz[i] = dwc2_readl(hsotg, HCTSIZ(i));
+		hr->hcidma[i] = dwc2_readl(hsotg, HCDMA(i));
+		hr->hcidmab[i] = dwc2_readl(hsotg, HCDMAB(i));
+	}
 
 	hr->hprt0 = dwc2_read_hprt0(hsotg);
 	hr->hfir = dwc2_readl(hsotg, HFIR);
@@ -5472,10 +5485,17 @@
 	hr->valid = false;
 
 	dwc2_writel(hsotg, hr->hcfg, HCFG);
+	dwc2_writel(hsotg, hr->hflbaddr, HFLBADDR);
 	dwc2_writel(hsotg, hr->haintmsk, HAINTMSK);
 
-	for (i = 0; i < hsotg->params.host_channels; ++i)
+	for (i = 0; i < hsotg->params.host_channels; ++i) {
+		dwc2_writel(hsotg, hr->hcchar[i], HCCHAR(i));
+		dwc2_writel(hsotg, hr->hcsplt[i], HCSPLT(i));
 		dwc2_writel(hsotg, hr->hcintmsk[i], HCINTMSK(i));
+		dwc2_writel(hsotg, hr->hctsiz[i], HCTSIZ(i));
+		dwc2_writel(hsotg, hr->hcidma[i], HCDMA(i));
+		dwc2_writel(hsotg, hr->hcidmab[i], HCDMAB(i));
+	}
 
 	dwc2_writel(hsotg, hr->hprt0, HPRT0);
 	dwc2_writel(hsotg, hr->hfir, HFIR);
@@ -5640,10 +5660,12 @@
 	dwc2_writel(hsotg, hr->hcfg, HCFG);
 
 	/* De-assert Wakeup Logic */
-	gpwrdn = dwc2_readl(hsotg, GPWRDN);
-	gpwrdn &= ~GPWRDN_PMUACTV;
-	dwc2_writel(hsotg, gpwrdn, GPWRDN);
-	udelay(10);
+	if (!(rem_wakeup && hsotg->hw_params.snpsid >= DWC2_CORE_REV_4_30a)) {
+		gpwrdn = dwc2_readl(hsotg, GPWRDN);
+		gpwrdn &= ~GPWRDN_PMUACTV;
+		dwc2_writel(hsotg, gpwrdn, GPWRDN);
+		udelay(10);
+	}
 
 	hprt0 = hr->hprt0;
 	hprt0 |= HPRT0_PWR;
@@ -5668,6 +5690,13 @@
 		hprt0 |= HPRT0_RES;
 		dwc2_writel(hsotg, hprt0, HPRT0);
 
+		/* De-assert Wakeup Logic */
+		if ((rem_wakeup && hsotg->hw_params.snpsid >= DWC2_CORE_REV_4_30a)) {
+			gpwrdn = dwc2_readl(hsotg, GPWRDN);
+			gpwrdn &= ~GPWRDN_PMUACTV;
+			dwc2_writel(hsotg, gpwrdn, GPWRDN);
+			udelay(10);
+		}
 		/* Wait for Resume time and then program HPRT again */
 		mdelay(100);
 		hprt0 &= ~HPRT0_RES;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/hcd_ddma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/hcd_ddma.c
@@ -589,7 +589,7 @@
 	idx = qh->td_last;
 	inc = qh->host_interval;
 	hsotg->frame_number = dwc2_hcd_get_frame_number(hsotg);
-	cur_idx = dwc2_frame_list_idx(hsotg->frame_number);
+	cur_idx = idx;
 	next_idx = dwc2_desclist_idx_inc(qh->td_last, inc, qh->dev_speed);
 
 	/*
@@ -896,20 +896,27 @@
 {
 	struct dwc2_dma_desc *dma_desc;
 	struct dwc2_hcd_iso_packet_desc *frame_desc;
+	u16 frame_desc_idx;
+	struct urb *usb_urb;
 	u16 remain = 0;
 	int rc = 0;
 
 	if (!qtd->urb)
 		return -EINVAL;
 
+	usb_urb = qtd->urb->priv;
+
 	dma_sync_single_for_cpu(hsotg->dev, qh->desc_list_dma + (idx *
 				sizeof(struct dwc2_dma_desc)),
 				sizeof(struct dwc2_dma_desc),
 				DMA_FROM_DEVICE);
 
 	dma_desc = &qh->desc_list[idx];
+	frame_desc_idx = (idx - qtd->isoc_td_first) & (usb_urb->number_of_packets - 1);
 
-	frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index_last];
+	frame_desc = &qtd->urb->iso_descs[frame_desc_idx];
+	if (idx == qtd->isoc_td_first)
+		usb_urb->start_frame = dwc2_hcd_get_frame_number(hsotg);
 	dma_desc->buf = (u32)(qtd->urb->dma + frame_desc->offset);
 	if (chan->ep_is_in)
 		remain = (dma_desc->status & HOST_DMA_ISOC_NBYTES_MASK) >>
@@ -930,7 +937,7 @@
 		frame_desc->status = 0;
 	}
 
-	if (++qtd->isoc_frame_index == qtd->urb->packet_count) {
+	if (++qtd->isoc_frame_index == usb_urb->number_of_packets) {
 		/*
 		 * urb->status is not used for isoc transfers here. The
 		 * individual frame_desc status are used instead.
@@ -1035,11 +1042,11 @@
 				return;
 			idx = dwc2_desclist_idx_inc(idx, qh->host_interval,
 						    chan->speed);
-			if (!rc)
+			if (rc == 0)
 				continue;
 
-			if (rc == DWC2_CMPL_DONE)
-				break;
+			if (rc == DWC2_CMPL_DONE || rc == DWC2_CMPL_STOP)
+				goto stop_scan;
 
 			/* rc == DWC2_CMPL_STOP */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/hcd_intr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/hcd_intr.c
@@ -2045,15 +2045,17 @@
 {
 	struct dwc2_qtd *qtd;
 	struct dwc2_host_chan *chan;
-	u32 hcint, hcintmsk;
+	u32 hcint, hcintraw, hcintmsk;
 
 	chan = hsotg->hc_ptr_array[chnum];
 
-	hcint = dwc2_readl(hsotg, HCINT(chnum));
+	hcintraw = dwc2_readl(hsotg, HCINT(chnum));
 	hcintmsk = dwc2_readl(hsotg, HCINTMSK(chnum));
+	hcint = hcintraw & hcintmsk;
+	dwc2_writel(hsotg, hcint, HCINT(chnum));
+
 	if (!chan) {
 		dev_err(hsotg->dev, "## hc_ptr_array for channel is NULL ##\n");
-		dwc2_writel(hsotg, hcint, HCINT(chnum));
 		return;
 	}
 
@@ -2062,11 +2064,9 @@
 			 chnum);
 		dev_vdbg(hsotg->dev,
 			 "  hcint 0x%08x, hcintmsk 0x%08x, hcint&hcintmsk 0x%08x\n",
-			 hcint, hcintmsk, hcint & hcintmsk);
+			 hcintraw, hcintmsk, hcint);
 	}
 
-	dwc2_writel(hsotg, hcint, HCINT(chnum));
-
 	/*
 	 * If we got an interrupt after someone called
 	 * dwc2_hcd_endpoint_disable() we don't want to crash below
@@ -2076,8 +2076,7 @@
 		return;
 	}
 
-	chan->hcint = hcint;
-	hcint &= hcintmsk;
+	chan->hcint = hcintraw;
 
 	/*
 	 * If the channel was halted due to a dequeue, the qtd list might
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/hcd_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/hcd_queue.c
@@ -59,7 +59,7 @@
 #define DWC2_UNRESERVE_DELAY (msecs_to_jiffies(5))
 
 /* If we get a NAK, wait this long before retrying */
-#define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
+#define DWC2_RETRY_WAIT_DELAY (1 * NSEC_PER_MSEC)
 
 /**
  * dwc2_periodic_channel_available() - Checks that a channel is available for a
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/hw.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/hw.h
@@ -728,7 +728,7 @@
 #define TXSTS_QTOP_TOKEN_MASK		(0x3 << 25)
 #define TXSTS_QTOP_TOKEN_SHIFT		25
 #define TXSTS_QTOP_TERMINATE		BIT(24)
-#define TXSTS_QSPCAVAIL_MASK		(0xff << 16)
+#define TXSTS_QSPCAVAIL_MASK		(0x7f << 16)
 #define TXSTS_QSPCAVAIL_SHIFT		16
 #define TXSTS_FSPCAVAIL_MASK		(0xffff << 0)
 #define TXSTS_FSPCAVAIL_SHIFT		0
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc2/platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc2/platform.c
@@ -121,13 +121,6 @@
 	return 0;
 }
 
-static void __dwc2_disable_regulators(void *data)
-{
-	struct dwc2_hsotg *hsotg = data;
-
-	regulator_bulk_disable(ARRAY_SIZE(hsotg->supplies), hsotg->supplies);
-}
-
 static int __dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg)
 {
 	struct platform_device *pdev = to_platform_device(hsotg->dev);
@@ -138,11 +131,6 @@
 	if (ret)
 		return ret;
 
-	ret = devm_add_action_or_reset(&pdev->dev,
-				       __dwc2_disable_regulators, hsotg);
-	if (ret)
-		return ret;
-
 	if (hsotg->clk) {
 		ret = clk_prepare_enable(hsotg->clk);
 		if (ret)
@@ -154,9 +142,9 @@
 	} else if (hsotg->plat && hsotg->plat->phy_init) {
 		ret = hsotg->plat->phy_init(pdev, hsotg->plat->phy_type);
 	} else {
-		ret = phy_power_on(hsotg->phy);
+		ret = phy_init(hsotg->phy);
 		if (ret == 0)
-			ret = phy_init(hsotg->phy);
+			ret = phy_power_on(hsotg->phy);
 	}
 
 	return ret;
@@ -188,9 +176,9 @@
 	} else if (hsotg->plat && hsotg->plat->phy_exit) {
 		ret = hsotg->plat->phy_exit(pdev, hsotg->plat->phy_type);
 	} else {
-		ret = phy_exit(hsotg->phy);
+		ret = phy_power_off(hsotg->phy);
 		if (ret == 0)
-			ret = phy_power_off(hsotg->phy);
+			ret = phy_exit(hsotg->phy);
 	}
 	if (ret)
 		return ret;
@@ -198,7 +186,7 @@
 	if (hsotg->clk)
 		clk_disable_unprepare(hsotg->clk);
 
-	return 0;
+	return regulator_bulk_disable(ARRAY_SIZE(hsotg->supplies), hsotg->supplies);
 }
 
 /**
@@ -217,6 +205,11 @@
 	return ret;
 }
 
+static void dwc2_reset_control_assert(void *data)
+{
+	reset_control_assert(data);
+}
+
 static int dwc2_lowlevel_hw_init(struct dwc2_hsotg *hsotg)
 {
 	int i, ret;
@@ -229,6 +222,10 @@
 	}
 
 	reset_control_deassert(hsotg->reset);
+	ret = devm_add_action_or_reset(hsotg->dev, dwc2_reset_control_assert,
+				       hsotg->reset);
+	if (ret)
+		return ret;
 
 	hsotg->reset_ecc = devm_reset_control_get_optional(hsotg->dev, "dwc2-ecc");
 	if (IS_ERR(hsotg->reset_ecc)) {
@@ -238,6 +235,10 @@
 	}
 
 	reset_control_deassert(hsotg->reset_ecc);
+	ret = devm_add_action_or_reset(hsotg->dev, dwc2_reset_control_assert,
+				       hsotg->reset_ecc);
+	if (ret)
+		return ret;
 
 	/*
 	 * Attempt to find a generic PHY, then look for an old style
@@ -343,7 +344,7 @@
 
 	/* Exit clock gating when driver is removed. */
 	if (hsotg->params.power_down == DWC2_POWER_DOWN_PARAM_NONE &&
-	    hsotg->bus_suspended) {
+	    hsotg->bus_suspended && !hsotg->params.no_clock_gating) {
 		if (dwc2_is_device_mode(hsotg))
 			dwc2_gadget_exit_clock_gating(hsotg, 0);
 		else
@@ -364,10 +365,7 @@
 	if (hsotg->ll_hw_enabled)
 		dwc2_lowlevel_hw_disable(hsotg);
 
-	reset_control_assert(hsotg->reset);
-	reset_control_assert(hsotg->reset_ecc);
-
-	return ret;
+	return 0;
 }
 
 /**
@@ -486,18 +484,6 @@
 
 	spin_lock_init(&hsotg->lock);
 
-	hsotg->irq = platform_get_irq(dev, 0);
-	if (hsotg->irq < 0)
-		return hsotg->irq;
-
-	dev_dbg(hsotg->dev, "registering common handler for irq%d\n",
-		hsotg->irq);
-	retval = devm_request_irq(hsotg->dev, hsotg->irq,
-				  dwc2_handle_common_intr, IRQF_SHARED,
-				  dev_name(hsotg->dev), hsotg);
-	if (retval)
-		return retval;
-
 	hsotg->vbus_supply = devm_regulator_get_optional(hsotg->dev, "vbus");
 	if (IS_ERR(hsotg->vbus_supply)) {
 		retval = PTR_ERR(hsotg->vbus_supply);
@@ -541,6 +527,20 @@
 	if (retval)
 		goto error;
 
+	hsotg->irq = platform_get_irq(dev, 0);
+	if (hsotg->irq < 0) {
+		retval = hsotg->irq;
+		goto error;
+	}
+
+	dev_dbg(hsotg->dev, "registering common handler for irq%d\n",
+		hsotg->irq);
+	retval = devm_request_irq(hsotg->dev, hsotg->irq,
+				  dwc2_handle_common_intr, IRQF_SHARED,
+				  dev_name(hsotg->dev), hsotg);
+	if (retval)
+		goto error;
+
 	/*
 	 * For OTG cores, set the force mode bits to reflect the value
 	 * of dr_mode. Force mode bits should not be touched at any
@@ -575,6 +575,9 @@
 		ggpio |= GGPIO_STM32_OTG_GCCFG_IDEN;
 		ggpio |= GGPIO_STM32_OTG_GCCFG_VBDEN;
 		dwc2_writel(hsotg, ggpio, GGPIO);
+
+		/* ID/VBUS detection startup time */
+		usleep_range(5000, 7000);
 	}
 
 	retval = dwc2_drd_init(hsotg);
@@ -655,7 +658,7 @@
 	if (hsotg->params.activate_stm_id_vb_detection)
 		regulator_disable(hsotg->usb33d);
 error:
-	if (hsotg->dr_mode != USB_DR_MODE_PERIPHERAL)
+	if (hsotg->ll_hw_enabled)
 		dwc2_lowlevel_hw_disable(hsotg);
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/Kconfig
@@ -24,6 +24,7 @@
 choice
 	bool "DWC3 Mode Selection"
 	default USB_DWC3_DUAL_ROLE if (USB && USB_GADGET)
+	default USB_DWC3_OTG if (USB && USB_GADGET && USB_OTG && USB_OTG_FSM)
 	default USB_DWC3_HOST if (USB && !USB_GADGET)
 	default USB_DWC3_GADGET if (!USB && USB_GADGET)
 
@@ -49,6 +50,15 @@
 	  This is the default mode of working of DWC3 controller where
 	  both host and gadget features are enabled.
 
+config USB_DWC3_OTG
+	bool "Dual Role mode + OTG"
+	depends on ((USB=y || USB=USB_DWC3) && \
+			(USB_GADGET=y || USB_GADGET=USB_DWC3) && \
+				USB_OTG && USB_OTG_FSM && PM)
+	help
+	  This is the default mode of working of DWC3 controller where
+	  both host and gadget features are enabled with OTG support.
+
 endchoice
 
 comment "Platform Glue Driver Support"
@@ -151,7 +161,7 @@
 
 config USB_DWC3_XILINX
 	tristate "Xilinx Platforms"
-	depends on (ARCH_ZYNQMP || ARCH_VERSAL) && OF
+	depends on (ARCH_ZYNQMP || ARCH_VERSAL) && OF && REGULATOR
 	default USB_DWC3
 	help
 	  Support Xilinx SoCs with DesignWare Core USB3 IP.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/Makefile
@@ -10,12 +10,18 @@
 	dwc3-y				+= trace.o
 endif
 
-ifneq ($(filter y,$(CONFIG_USB_DWC3_HOST) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
+ifneq ($(filter y,$(CONFIG_USB_DWC3_HOST) $(CONFIG_USB_DWC3_DUAL_ROLE)\
+		 $(CONFIG_USB_DWC3_OTG)),)
 	dwc3-y				+= host.o
 endif
 
-ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
-	dwc3-y				+= gadget.o ep0.o
+ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET) $(CONFIG_USB_DWC3_DUAL_ROLE)\
+		 $(CONFIG_USB_DWC3_OTG)),)
+	dwc3-y				+= gadget.o ep0.o gadget_hibernation.o
+endif
+
+ifneq ($(CONFIG_USB_DWC3_OTG),)
+	dwc3-y				+= otg.o
 endif
 
 ifneq ($(CONFIG_USB_DWC3_DUAL_ROLE),)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/core.c
@@ -25,6 +25,7 @@
 #include <linux/of.h>
 #include <linux/acpi.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/of_address.h>
 #include <linux/reset.h>
 
 #include <linux/usb/ch9.h>
@@ -78,17 +79,6 @@
 			mode = USB_DR_MODE_HOST;
 		else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET))
 			mode = USB_DR_MODE_PERIPHERAL;
-
-		/*
-		 * DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG
-		 * mode. If the controller supports DRD but the dr_mode is not
-		 * specified or set to OTG, then set the mode to peripheral.
-		 */
-		if (mode == USB_DR_MODE_OTG &&
-		    (!IS_ENABLED(CONFIG_USB_ROLE_SWITCH) ||
-		     !device_property_read_bool(dwc->dev, "usb-role-switch")) &&
-		    !DWC3_VER_IS_PRIOR(DWC3, 330A))
-			mode = USB_DR_MODE_PERIPHERAL;
 	}
 
 	if (mode != dwc->dr_mode) {
@@ -102,11 +92,45 @@
 	return 0;
 }
 
-void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode)
+void dwc3_enable_susphy(struct dwc3 *dwc, bool enable)
 {
 	u32 reg;
 
+	reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
+	if (enable && !dwc->dis_u3_susphy_quirk)
+		reg |= DWC3_GUSB3PIPECTL_SUSPHY;
+	else
+		reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
+
+	dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
+
+	reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
+	if (enable && !dwc->dis_u2_susphy_quirk)
+		reg |= DWC3_GUSB2PHYCFG_SUSPHY;
+	else
+		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
+
+	dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+}
+
+void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode, bool ignore_susphy)
+{
+	unsigned int hw_mode;
+	u32 reg;
+
 	reg = dwc3_readl(dwc->regs, DWC3_GCTL);
+
+	 /*
+	  * For DRD controllers, GUSB3PIPECTL.SUSPENDENABLE and
+	  * GUSB2PHYCFG.SUSPHY should be cleared during mode switching,
+	  * and they can be set after core initialization.
+	  */
+	hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
+	if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD && !ignore_susphy) {
+		if (DWC3_GCTL_PRTCAP(reg) != mode)
+			dwc3_enable_susphy(dwc, false);
+	}
+
 	reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
 	reg |= DWC3_GCTL_PRTCAPDIR(mode);
 	dwc3_writel(dwc->regs, DWC3_GCTL, reg);
@@ -114,29 +138,31 @@
 	dwc->current_dr_role = mode;
 }
 
-static int dwc3_core_soft_reset(struct dwc3 *dwc);
-
 static void __dwc3_set_mode(struct work_struct *work)
 {
 	struct dwc3 *dwc = work_to_dwc(work);
 	unsigned long flags;
 	int ret;
 	u32 reg;
+	u32 desired_dr_role;
 
 	mutex_lock(&dwc->mutex);
+	spin_lock_irqsave(&dwc->lock, flags);
+	desired_dr_role = dwc->desired_dr_role;
+	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	pm_runtime_get_sync(dwc->dev);
 
 	if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_OTG)
 		dwc3_otg_update(dwc, 0);
 
-	if (!dwc->desired_dr_role)
+	if (!desired_dr_role)
 		goto out;
 
-	if (dwc->desired_dr_role == dwc->current_dr_role)
+	if (desired_dr_role == dwc->current_dr_role)
 		goto out;
 
-	if (dwc->desired_dr_role == DWC3_GCTL_PRTCAP_OTG && dwc->edev)
+	if (desired_dr_role == DWC3_GCTL_PRTCAP_OTG && dwc->edev)
 		goto out;
 
 	switch (dwc->current_dr_role) {
@@ -158,8 +184,13 @@
 		break;
 	}
 
-	/* For DRD host or device mode only */
-	if (dwc->desired_dr_role != DWC3_GCTL_PRTCAP_OTG) {
+	/*
+	 * When current_dr_role is not set, there's no role switching.
+	 * Only perform GCTL.CoreSoftReset when there's DRD role switching.
+	 */
+	if (dwc->current_dr_role && ((DWC3_IP_IS(DWC3) ||
+			DWC3_VER_IS_PRIOR(DWC31, 190A)) &&
+			desired_dr_role != DWC3_GCTL_PRTCAP_OTG)) {
 		reg = dwc3_readl(dwc->regs, DWC3_GCTL);
 		reg |= DWC3_GCTL_CORESOFTRESET;
 		dwc3_writel(dwc->regs, DWC3_GCTL, reg);
@@ -179,11 +210,11 @@
 
 	spin_lock_irqsave(&dwc->lock, flags);
 
-	dwc3_set_prtcap(dwc, dwc->desired_dr_role);
+	dwc3_set_prtcap(dwc, desired_dr_role, false);
 
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
-	switch (dwc->desired_dr_role) {
+	switch (desired_dr_role) {
 	case DWC3_GCTL_PRTCAP_HOST:
 		ret = dwc3_host_init(dwc);
 		if (ret) {
@@ -260,7 +291,7 @@
  * dwc3_core_soft_reset - Issues core soft reset and PHY reset
  * @dwc: pointer to our context structure
  */
-static int dwc3_core_soft_reset(struct dwc3 *dwc)
+int dwc3_core_soft_reset(struct dwc3 *dwc)
 {
 	u32		reg;
 	int		retries = 1000;
@@ -269,13 +300,16 @@
 	 * We're resetting only the device side because, if we're in host mode,
 	 * XHCI driver will reset the host block. If dwc3 was configured for
 	 * host-only mode, then we can return early.
+	 * When hibernated don't perform core soft reset.
 	 */
-	if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
+	if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST
+	    || dwc->is_hibernated == true)
 		return 0;
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	reg |= DWC3_DCTL_CSFTRST;
-	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	reg &= ~DWC3_DCTL_RUN_STOP;
+	dwc3_gadget_dctl_write_safe(dwc, reg);
 
 	/*
 	 * For DWC_usb31 controller 1.90a and later, the DCTL.CSFRST bit
@@ -317,7 +351,7 @@
  */
 static void dwc3_frame_length_adjustment(struct dwc3 *dwc)
 {
-	u32 reg;
+	u32 reg, gfladj;
 	u32 dft;
 
 	if (DWC3_VER_IS_PRIOR(DWC3, 250A))
@@ -326,13 +360,24 @@
 	if (dwc->fladj == 0)
 		return;
 
+	/* Save the initial DWC3_GFLADJ register value */
 	reg = dwc3_readl(dwc->regs, DWC3_GFLADJ);
+	gfladj = reg;
+
+	if (dwc->refclk_fladj) {
+		reg &= ~DWC3_GFLADJ_REFCLK_FLADJ;
+		reg |= (dwc->fladj & DWC3_GFLADJ_REFCLK_FLADJ);
+	}
+
 	dft = reg & DWC3_GFLADJ_30MHZ_MASK;
 	if (dft != dwc->fladj) {
 		reg &= ~DWC3_GFLADJ_30MHZ_MASK;
 		reg |= DWC3_GFLADJ_30MHZ_SDBND_SEL | dwc->fladj;
-		dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
 	}
+
+	/* Update DWC3_GFLADJ if there is any change from initial value */
+	if (reg != gfladj)
+		dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
 }
 
 /**
@@ -381,7 +426,7 @@
  * dwc3_free_event_buffers - frees all allocated event buffers
  * @dwc: Pointer to our controller context structure
  */
-static void dwc3_free_event_buffers(struct dwc3 *dwc)
+void dwc3_free_event_buffers(struct dwc3 *dwc)
 {
 	struct dwc3_event_buffer	*evt;
 
@@ -398,9 +443,16 @@
  * Returns 0 on success otherwise negative errno. In the error case, dwc
  * may contain some buffers allocated but not all which were requested.
  */
-static int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length)
+int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length)
 {
 	struct dwc3_event_buffer *evt;
+	unsigned int hw_mode;
+
+	hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
+	if (hw_mode == DWC3_GHWPARAMS0_MODE_HOST) {
+		dwc->ev_buf = NULL;
+		return 0;
+	}
 
 	evt = dwc3_alloc_one_event_buffer(dwc, length);
 	if (IS_ERR(evt)) {
@@ -421,6 +473,13 @@
 int dwc3_event_buffers_setup(struct dwc3 *dwc)
 {
 	struct dwc3_event_buffer	*evt;
+	u32				reg;
+
+	if (!dwc->ev_buf)
+		return 0;
+
+	if (dwc->dr_mode == USB_DR_MODE_HOST)
+		return 0;
 
 	evt = dwc->ev_buf;
 	evt->lpos = 0;
@@ -430,14 +489,27 @@
 			upper_32_bits(evt->dma));
 	dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
 			DWC3_GEVNTSIZ_SIZE(evt->length));
-	dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
 
+	/* Clear any stale event */
+	reg = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
+	dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), reg);
 	return 0;
 }
 
 void dwc3_event_buffers_cleanup(struct dwc3 *dwc)
 {
 	struct dwc3_event_buffer	*evt;
+	u32				reg;
+
+	if (!dwc->ev_buf)
+		return;
+	/*
+	 * Exynos platforms may not be able to access event buffer if the
+	 * controller failed to halt on dwc3_core_exit().
+	 */
+	reg = dwc3_readl(dwc->regs, DWC3_DSTS);
+	if (!(reg & DWC3_DSTS_DEVCTRLHLT))
+		return;
 
 	evt = dwc->ev_buf;
 
@@ -447,31 +519,53 @@
 	dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 0);
 	dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_INTMASK
 			| DWC3_GEVNTSIZ_SIZE(0));
-	dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
+
+	/* Clear any stale event */
+	reg = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
+	dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), reg);
 }
 
 static int dwc3_alloc_scratch_buffers(struct dwc3 *dwc)
 {
+	u32 size;
+
+	if (dwc->dr_mode == USB_DR_MODE_HOST)
+		return 0;
+
 	if (!dwc->has_hibernation)
 		return 0;
 
 	if (!dwc->nr_scratch)
 		return 0;
 
-	dwc->scratchbuf = kmalloc_array(dwc->nr_scratch,
-			DWC3_SCRATCHBUF_SIZE, GFP_KERNEL);
+	/* Allocate only if scratchbuf is NULL */
+	if (dwc->scratchbuf)
+		return 0;
+
+	size = dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE;
+
+	dwc->scratchbuf = kzalloc(size, GFP_KERNEL);
 	if (!dwc->scratchbuf)
 		return -ENOMEM;
 
+	dwc->scratch_addr = dma_map_single(dwc->dev, dwc->scratchbuf, size,
+					   DMA_BIDIRECTIONAL);
+	if (dma_mapping_error(dwc->dev, dwc->scratch_addr)) {
+		dev_err(dwc->dev, "failed to map scratch buffer\n");
+		return -EFAULT;
+	}
+
 	return 0;
 }
 
 static int dwc3_setup_scratch_buffers(struct dwc3 *dwc)
 {
-	dma_addr_t scratch_addr;
 	u32 param;
 	int ret;
 
+	if (dwc->dr_mode == USB_DR_MODE_HOST)
+		return 0;
+
 	if (!dwc->has_hibernation)
 		return 0;
 
@@ -479,28 +573,17 @@
 		return 0;
 
 	 /* should never fall here */
-	if (!WARN_ON(dwc->scratchbuf))
+	if (WARN_ON(!dwc->scratchbuf))
 		return 0;
 
-	scratch_addr = dma_map_single(dwc->sysdev, dwc->scratchbuf,
-			dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE,
-			DMA_BIDIRECTIONAL);
-	if (dma_mapping_error(dwc->sysdev, scratch_addr)) {
-		dev_err(dwc->sysdev, "failed to map scratch buffer\n");
-		ret = -EFAULT;
-		goto err0;
-	}
-
-	dwc->scratch_addr = scratch_addr;
-
-	param = lower_32_bits(scratch_addr);
+	param = lower_32_bits(dwc->scratch_addr);
 
 	ret = dwc3_send_gadget_generic_command(dwc,
 			DWC3_DGCMD_SET_SCRATCHPAD_ADDR_LO, param);
 	if (ret < 0)
 		goto err1;
 
-	param = upper_32_bits(scratch_addr);
+	param = upper_32_bits(dwc->scratch_addr);
 
 	ret = dwc3_send_gadget_generic_command(dwc,
 			DWC3_DGCMD_SET_SCRATCHPAD_ADDR_HI, param);
@@ -510,15 +593,19 @@
 	return 0;
 
 err1:
-	dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch *
-			DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL);
+	dma_unmap_single(dwc->sysdev, dwc->scratch_addr,
+			(size_t)(dwc->nr_scratch *
+			(size_t)DWC3_SCRATCHBUF_SIZE),
+			DMA_BIDIRECTIONAL);
 
-err0:
 	return ret;
 }
 
 static void dwc3_free_scratch_buffers(struct dwc3 *dwc)
 {
+	if (dwc->dr_mode == USB_DR_MODE_HOST)
+		return;
+
 	if (!dwc->has_hibernation)
 		return;
 
@@ -526,11 +613,13 @@
 		return;
 
 	 /* should never fall here */
-	if (!WARN_ON(dwc->scratchbuf))
+	if (WARN_ON(!dwc->scratchbuf))
 		return;
 
-	dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch *
-			DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL);
+	dma_unmap_single(dwc->sysdev, dwc->scratch_addr,
+			(size_t)(dwc->nr_scratch *
+			(size_t)DWC3_SCRATCHBUF_SIZE),
+			DMA_BIDIRECTIONAL);
 	kfree(dwc->scratchbuf);
 }
 
@@ -559,6 +648,25 @@
 		parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9);
 }
 
+static void dwc3_config_soc_bus(struct dwc3 *dwc)
+{
+	/*
+	 * Check if CCI is enabled for USB. Returns true
+	 * if the node has property 'dma-coherent'. Otherwise
+	 * returns false.
+	 */
+	if (of_dma_is_coherent(dwc->dev->of_node)) {
+		u32 reg;
+
+		reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
+		reg |= DWC3_GSBUSCFG0_DATRDREQINFO |
+			DWC3_GSBUSCFG0_DESRDREQINFO |
+			DWC3_GSBUSCFG0_DATWRREQINFO |
+			DWC3_GSBUSCFG0_DESWRREQINFO;
+		dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
+	}
+}
+
 static int dwc3_core_ulpi_init(struct dwc3 *dwc)
 {
 	int intf;
@@ -585,11 +693,8 @@
  */
 static int dwc3_phy_setup(struct dwc3 *dwc)
 {
-	unsigned int hw_mode;
 	u32 reg;
 
-	hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
-
 	reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
 
 	/*
@@ -598,22 +703,8 @@
 	 */
 	reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX;
 
-	/*
-	 * Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY
-	 * to '0' during coreConsultant configuration. So default value
-	 * will be '0' when the core is reset. Application needs to set it
-	 * to '1' after the core initialization is completed.
-	 */
-	if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A))
-		reg |= DWC3_GUSB3PIPECTL_SUSPHY;
-
-	/*
-	 * For DRD controllers, GUSB3PIPECTL.SUSPENDENABLE must be cleared after
-	 * power-on reset, and it can be set after core initialization, which is
-	 * after device soft-reset during initialization.
-	 */
-	if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD)
-		reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
+	/* Ensure the GUSB3PIPECTL.SUSPENDENABLE is cleared prior to phy init. */
+	reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
 
 	if (dwc->u2ss_inp3_quirk)
 		reg |= DWC3_GUSB3PIPECTL_U2SSINP3OK;
@@ -639,9 +730,6 @@
 	if (dwc->tx_de_emphasis_quirk)
 		reg |= DWC3_GUSB3PIPECTL_TX_DEEPH(dwc->tx_de_emphasis);
 
-	if (dwc->dis_u3_susphy_quirk)
-		reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
-
 	if (dwc->dis_del_phy_power_chg_quirk)
 		reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE;
 
@@ -688,25 +776,8 @@
 		break;
 	}
 
-	/*
-	 * Above 1.94a, it is recommended to set DWC3_GUSB2PHYCFG_SUSPHY to
-	 * '0' during coreConsultant configuration. So default value will
-	 * be '0' when the core is reset. Application needs to set it to
-	 * '1' after the core initialization is completed.
-	 */
-	if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A))
-		reg |= DWC3_GUSB2PHYCFG_SUSPHY;
-
-	/*
-	 * For DRD controllers, GUSB2PHYCFG.SUSPHY must be cleared after
-	 * power-on reset, and it can be set after core initialization, which is
-	 * after device soft-reset during initialization.
-	 */
-	if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD)
-		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
-
-	if (dwc->dis_u2_susphy_quirk)
-		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
+	/* Ensure the GUSB2PHYCFG.SUSPHY is cleared prior to phy init. */
+	reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
 
 	if (dwc->dis_enblslpm_quirk)
 		reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
@@ -725,15 +796,16 @@
 {
 	dwc3_event_buffers_cleanup(dwc);
 
+	usb_phy_set_suspend(dwc->usb2_phy, 1);
+	usb_phy_set_suspend(dwc->usb3_phy, 1);
+	phy_power_off(dwc->usb2_generic_phy);
+	phy_power_off(dwc->usb3_generic_phy);
+
 	usb_phy_shutdown(dwc->usb2_phy);
 	usb_phy_shutdown(dwc->usb3_phy);
 	phy_exit(dwc->usb2_generic_phy);
 	phy_exit(dwc->usb3_generic_phy);
 
-	usb_phy_set_suspend(dwc->usb2_phy, 1);
-	usb_phy_set_suspend(dwc->usb3_phy, 1);
-	phy_power_off(dwc->usb2_generic_phy);
-	phy_power_off(dwc->usb3_generic_phy);
 	clk_bulk_disable_unprepare(dwc->num_clks, dwc->clks);
 	reset_control_assert(dwc->reset);
 }
@@ -790,12 +862,14 @@
 	case DWC3_GHWPARAMS1_EN_PWROPT_HIB:
 		/* enable hibernation here */
 		dwc->nr_scratch = DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(hwparams4);
+		dwc->has_hibernation = 1;
 
 		/*
 		 * REVISIT Enabling this bit so that host-mode hibernation
 		 * will work. Device-mode hibernation is not yet implemented.
 		 */
-		reg |= DWC3_GCTL_GBLHIBERNATIONEN;
+		if (dwc->dr_mode == USB_DR_MODE_HOST)
+			reg |= DWC3_GCTL_GBLHIBERNATIONEN;
 		break;
 	default:
 		/* nothing */
@@ -934,7 +1008,7 @@
  *
  * Returns 0 on success otherwise negative errno.
  */
-static int dwc3_core_init(struct dwc3 *dwc)
+int dwc3_core_init(struct dwc3 *dwc)
 {
 	unsigned int		hw_mode;
 	u32			reg;
@@ -954,8 +1028,13 @@
 
 	if (!dwc->ulpi_ready) {
 		ret = dwc3_core_ulpi_init(dwc);
-		if (ret)
+		if (ret) {
+			if (ret == -ETIMEDOUT) {
+				dwc3_core_soft_reset(dwc);
+				ret = -EPROBE_DEFER;
+			}
 			goto err0;
+		}
 		dwc->ulpi_ready = true;
 	}
 
@@ -982,33 +1061,31 @@
 	if (ret)
 		goto err1;
 
-	if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD &&
-	    !DWC3_VER_IS_WITHIN(DWC3, ANY, 194A)) {
-		if (!dwc->dis_u3_susphy_quirk) {
-			reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
-			reg |= DWC3_GUSB3PIPECTL_SUSPHY;
-			dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
-		}
+	dwc3_core_setup_global_control(dwc);
+	dwc3_core_num_eps(dwc);
 
-		if (!dwc->dis_u2_susphy_quirk) {
-			reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
-			reg |= DWC3_GUSB2PHYCFG_SUSPHY;
-			dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+	if (dwc->scratchbuf == NULL) {
+		ret = dwc3_alloc_scratch_buffers(dwc);
+		if (ret) {
+			dev_err(dwc->dev,
+				"Not enough memory for scratch buffers\n");
+			goto err1;
 		}
 	}
 
-	dwc3_core_setup_global_control(dwc);
-	dwc3_core_num_eps(dwc);
-
 	ret = dwc3_setup_scratch_buffers(dwc);
-	if (ret)
+	if (ret) {
+		dev_err(dwc->dev, "Failed to setup scratch buffers: %d\n", ret);
 		goto err1;
+	}
 
 	/* Adjust Frame Length */
 	dwc3_frame_length_adjustment(dwc);
 
 	dwc3_set_incr_burst_type(dwc);
 
+	dwc3_config_soc_bus(dwc);
+
 	usb_phy_set_suspend(dwc->usb2_phy, 0);
 	usb_phy_set_suspend(dwc->usb3_phy, 0);
 	ret = phy_power_on(dwc->usb2_generic_phy);
@@ -1025,6 +1102,21 @@
 		goto err4;
 	}
 
+	switch (dwc->dr_mode) {
+	case USB_DR_MODE_PERIPHERAL:
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true);
+		break;
+	case USB_DR_MODE_HOST:
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, true);
+		break;
+	case USB_DR_MODE_OTG:
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true);
+		break;
+	default:
+		dev_warn(dwc->dev, "Unsupported mode %d\n", dwc->dr_mode);
+		break;
+	}
+
 	/*
 	 * ENDXFER polling is available on version 3.10a and later of
 	 * the DWC_usb3 controller. It is NOT available in the
@@ -1036,6 +1128,50 @@
 		dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
 	}
 
+	/*
+	 * STAR 9001285599: This issue affects DWC_usb3 version 3.20a
+	 * only. If the PM TIMER ECM is enabled through GUCTL2[19], the
+	 * link compliance test (TD7.21) may fail. If the ECN is not
+	 * enabled (GUCTL2[19] = 0), the controller will use the old timer
+	 * value (5us), which is still acceptable for the link compliance
+	 * test. Therefore, do not enable PM TIMER ECM in 3.20a by
+	 * setting GUCTL2[19] by default; instead, use GUCTL2[19] = 0.
+	 */
+	if (DWC3_VER_IS(DWC3, 320A)) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
+		reg &= ~DWC3_GUCTL2_LC_TIMER;
+		dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
+	}
+
+	/*
+	 * When configured in HOST mode, after issuing U3/L2 exit controller
+	 * fails to send proper CRC checksum in CRC5 feild. Because of this
+	 * behaviour Transaction Error is generated, resulting in reset and
+	 * re-enumeration of usb device attached. All the termsel, xcvrsel,
+	 * opmode becomes 0 during end of resume. Enabling bit 10 of GUCTL1
+	 * will correct this problem. This option is to support certain
+	 * legacy ULPI PHYs.
+	 */
+	if (dwc->resume_hs_terminations) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
+		reg |= DWC3_GUCTL1_RESUME_OPMODE_HS_HOST;
+		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
+	}
+
+	/* SNPS controller when configureed in HOST mode maintains Inter Packet
+	 * Delay (IPD) of ~380ns which works with most of the super-speed hubs
+	 * except VIA-LAB hubs. When IPD is ~380ns HOST controller fails to
+	 * enumerate FS/LS devices when connected behind VIA-LAB hubs.
+	 * Enabling bit 9 of GUCTL1 enables the workaround in HW to reduce the
+	 * ULPI clock latency by 1 cycle, thus reducing the IPD (~360ns) and
+	 * making controller enumerate FS/LS devices connected behind VIA-LAB.
+	 */
+	if (dwc->enable_guctl1_ipd_quirk) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
+		reg |= DWC3_GUCTL1_IPD_QUIRK;
+		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
+	}
+
 	if (!DWC3_VER_IS_PRIOR(DWC3, 250A)) {
 		reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
 
@@ -1064,22 +1200,6 @@
 		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
 	}
 
-	if (dwc->dr_mode == USB_DR_MODE_HOST ||
-	    dwc->dr_mode == USB_DR_MODE_OTG) {
-		reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
-
-		/*
-		 * Enable Auto retry Feature to make the controller operating in
-		 * Host mode on seeing transaction errors(CRC errors or internal
-		 * overrun scenerios) on IN transfers to reply to the device
-		 * with a non-terminating retry ACK (i.e, an ACK transcation
-		 * packet with Retry=1 & Nump != 0)
-		 */
-		reg |= DWC3_GUCTL_HSTINAUTORETRY;
-
-		dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
-	}
-
 	/*
 	 * Must config both number of packets and max burst settings to enable
 	 * RX and/or TX threshold.
@@ -1117,6 +1237,25 @@
 		}
 	}
 
+	/*
+	 * Above DWC_usb3.0 1.94a, it is recommended to set
+	 * DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY to '0' during
+	 * coreConsultant configuration. So default value will be '0' when the
+	 * core is reset. Application needs to set it to '1' after the core
+	 * initialization is completed.
+	 *
+	 * Certain phy requires to be in P0 power state during initialization.
+	 * Make sure GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY are clear
+	 * prior to phy init to maintain in the P0 state.
+	 *
+	 * After phy initialization, some phy operations can only be executed
+	 * while in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
+	 * GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid
+	 * blocking phy ops.
+	 */
+	if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A))
+		dwc3_enable_susphy(dwc, true);
+
 	return 0;
 
 err4:
@@ -1204,7 +1343,7 @@
 
 	switch (dwc->dr_mode) {
 	case USB_DR_MODE_PERIPHERAL:
-		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, false);
 
 		if (dwc->usb2_phy)
 			otg_set_vbus(dwc->usb2_phy->otg, false);
@@ -1216,7 +1355,7 @@
 			return dev_err_probe(dev, ret, "failed to initialize gadget\n");
 		break;
 	case USB_DR_MODE_HOST:
-		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, false);
 
 		if (dwc->usb2_phy)
 			otg_set_vbus(dwc->usb2_phy->otg, true);
@@ -1232,6 +1371,11 @@
 		ret = dwc3_drd_init(dwc);
 		if (ret)
 			return dev_err_probe(dev, ret, "failed to initialize dual-role\n");
+
+#if IS_ENABLED(CONFIG_USB_DWC3_OTG)
+		dwc->current_dr_role = 0;
+		dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_OTG);
+#endif
 		break;
 	default:
 		dev_err(dev, "Unsupported mode of operation %d\n", dwc->dr_mode);
@@ -1259,7 +1403,7 @@
 	}
 
 	/* de-assert DRVVBUS for HOST and OTG mode */
-	dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
+	dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true);
 }
 
 static void dwc3_get_properties(struct dwc3 *dwc)
@@ -1268,13 +1412,11 @@
 	u8			lpm_nyet_threshold;
 	u8			tx_de_emphasis;
 	u8			hird_threshold;
-	u8			rx_thr_num_pkt_prd;
-	u8			rx_max_burst_prd;
-	u8			tx_thr_num_pkt_prd;
-	u8			tx_max_burst_prd;
+	u8			rx_thr_num_pkt_prd = 0;
+	u8			rx_max_burst_prd = 0;
+	u8			tx_thr_num_pkt_prd = 0;
+	u8			tx_max_burst_prd = 0;
 	u8			tx_fifo_resize_max_num;
-	const char		*usb_psy_name;
-	int			ret;
 
 	/* default to highest possible threshold */
 	lpm_nyet_threshold = 0xf;
@@ -1307,13 +1449,6 @@
 	else
 		dwc->sysdev = dwc->dev;
 
-	ret = device_property_read_string(dev, "usb-psy-name", &usb_psy_name);
-	if (ret >= 0) {
-		dwc->usb_psy = power_supply_get_by_name(usb_psy_name);
-		if (!dwc->usb_psy)
-			dev_err(dev, "couldn't get usb power supply\n");
-	}
-
 	dwc->has_lpm_erratum = device_property_read_bool(dev,
 				"snps,has-lpm-erratum");
 	device_property_read_u8(dev, "snps,lpm-nyet-threshold",
@@ -1378,6 +1513,8 @@
 				"snps,dis-del-phy-power-chg-quirk");
 	dwc->dis_tx_ipgap_linecheck_quirk = device_property_read_bool(dev,
 				"snps,dis-tx-ipgap-linecheck-quirk");
+	dwc->resume_hs_terminations = device_property_read_bool(dev,
+				"snps,resume-hs-terminations");
 	dwc->parkmode_disable_ss_quirk = device_property_read_bool(dev,
 				"snps,parkmode-disable-ss-quirk");
 
@@ -1390,6 +1527,10 @@
 	device_property_read_u32(dev, "snps,quirk-frame-length-adjustment",
 				 &dwc->fladj);
 
+	dwc->refclk_fladj = device_property_read_bool(dev,
+						      "snps,refclk_fladj");
+	dwc->enable_guctl1_ipd_quirk = device_property_read_bool(dev,
+				"snps,enable_guctl1_ipd_quirk");
 	dwc->dis_metastability_quirk = device_property_read_bool(dev,
 				"snps,dis_metastability_quirk");
 
@@ -1407,8 +1548,6 @@
 	dwc->tx_thr_num_pkt_prd = tx_thr_num_pkt_prd;
 	dwc->tx_max_burst_prd = tx_max_burst_prd;
 
-	dwc->imod_interval = 0;
-
 	dwc->tx_fifo_resize_max_num = tx_fifo_resize_max_num;
 }
 
@@ -1426,21 +1565,19 @@
 	unsigned int hwparam_gen =
 		DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3);
 
-	/* Check for proper value of imod_interval */
-	if (dwc->imod_interval && !dwc3_has_imod(dwc)) {
-		dev_warn(dwc->dev, "Interrupt moderation not supported\n");
-		dwc->imod_interval = 0;
-	}
-
 	/*
+	 * Enable IMOD for all supporting controllers.
+	 *
+	 * Particularly, DWC_usb3 v3.00a must enable this feature for
+	 * the following reason:
+	 *
 	 * Workaround for STAR 9000961433 which affects only version
 	 * 3.00a of the DWC_usb3 core. This prevents the controller
 	 * interrupt from being masked while handling events. IMOD
 	 * allows us to work around this issue. Enable it for the
 	 * affected version.
 	 */
-	if (!dwc->imod_interval &&
-	    DWC3_VER_IS(DWC3, 300A))
+	if (dwc3_has_imod((dwc)))
 		dwc->imod_interval = 1;
 
 	/* Check the maximum_speed parameter */
@@ -1521,14 +1658,30 @@
 	}
 }
 
+static struct power_supply *dwc3_get_usb_power_supply(struct dwc3 *dwc)
+{
+	struct power_supply *usb_psy;
+	const char *usb_psy_name;
+	int ret;
+
+	ret = device_property_read_string(dwc->dev, "usb-psy-name", &usb_psy_name);
+	if (ret < 0)
+		return NULL;
+
+	usb_psy = power_supply_get_by_name(usb_psy_name);
+	if (!usb_psy)
+		return ERR_PTR(-EPROBE_DEFER);
+
+	return usb_psy;
+}
+
 static int dwc3_probe(struct platform_device *pdev)
 {
 	struct device		*dev = &pdev->dev;
 	struct resource		*res, dwc_res;
 	struct dwc3		*dwc;
-
 	int			ret;
-
+	u32			mdwidth;
 	void __iomem		*regs;
 
 	dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL);
@@ -1565,9 +1718,9 @@
 
 	dwc3_get_properties(dwc);
 
-	ret = dma_set_mask_and_coherent(dwc->sysdev, DMA_BIT_MASK(64));
-	if (ret)
-		return ret;
+	dwc->usb_psy = dwc3_get_usb_power_supply(dwc);
+	if (IS_ERR(dwc->usb_psy))
+		return dev_err_probe(dev, PTR_ERR(dwc->usb_psy), "couldn't get usb power supply\n");
 
 	dwc->reset = devm_reset_control_array_get_optional_shared(dev);
 	if (IS_ERR(dwc->reset))
@@ -1605,16 +1758,26 @@
 	platform_set_drvdata(pdev, dwc);
 	dwc3_cache_hwparams(dwc);
 
+	if (!dwc->sysdev_is_parent &&
+	    DWC3_GHWPARAMS0_AWIDTH(dwc->hwparams.hwparams0) == 64) {
+		ret = dma_set_mask_and_coherent(dwc->sysdev, DMA_BIT_MASK(64));
+		if (ret)
+			goto disable_clks;
+	}
+
 	spin_lock_init(&dwc->lock);
 	mutex_init(&dwc->mutex);
 
+	/* Set dma coherent mask to DMA BUS data width */
+	mdwidth = DWC3_GHWPARAMS0_MDWIDTH(dwc->hwparams.hwparams0);
+	dev_dbg(dev, "Enabling %d-bit DMA addresses.\n", mdwidth);
+	dma_set_coherent_mask(dev, DMA_BIT_MASK(mdwidth));
+
+	pm_runtime_get_noresume(dev);
 	pm_runtime_set_active(dev);
 	pm_runtime_use_autosuspend(dev);
 	pm_runtime_set_autosuspend_delay(dev, DWC3_DEFAULT_AUTOSUSPEND_DELAY);
 	pm_runtime_enable(dev);
-	ret = pm_runtime_get_sync(dev);
-	if (ret < 0)
-		goto err1;
 
 	pm_runtime_forbid(dev);
 
@@ -1629,10 +1792,6 @@
 	if (ret)
 		goto err3;
 
-	ret = dwc3_alloc_scratch_buffers(dwc);
-	if (ret)
-		goto err3;
-
 	ret = dwc3_core_init(dwc);
 	if (ret) {
 		dev_err_probe(dev, ret, "failed to initialize core\n");
@@ -1646,24 +1805,41 @@
 	if (ret)
 		goto err5;
 
+	/*
+	 * DWC3 controller has a Power Management Unit(PMU) module
+	 * which requests the power controller for entering into
+	 * D3/D0 state. Try getting the regulator.
+	 */
+	dwc->dwc3_pmu = devm_regulator_get(dev,
+					   dev->parent->of_node->full_name);
+	if (!IS_ERR(dwc->dwc3_pmu)) {
+		ret = regulator_enable(dwc->dwc3_pmu);
+		if (ret) {
+			dev_err(dev, "Failed to enable dwc3_pmu supply\n");
+			goto err5;
+		}
+	}
+
 	pm_runtime_put(dev);
 
+	dma_set_max_seg_size(dev, UINT_MAX);
+
 	return 0;
 
 err5:
 	dwc3_debugfs_exit(dwc);
 	dwc3_event_buffers_cleanup(dwc);
 
-	usb_phy_shutdown(dwc->usb2_phy);
-	usb_phy_shutdown(dwc->usb3_phy);
-	phy_exit(dwc->usb2_generic_phy);
-	phy_exit(dwc->usb3_generic_phy);
-
 	usb_phy_set_suspend(dwc->usb2_phy, 1);
 	usb_phy_set_suspend(dwc->usb3_phy, 1);
 	phy_power_off(dwc->usb2_generic_phy);
 	phy_power_off(dwc->usb3_generic_phy);
 
+	usb_phy_shutdown(dwc->usb2_phy);
+	usb_phy_shutdown(dwc->usb3_phy);
+	phy_exit(dwc->usb2_generic_phy);
+	phy_exit(dwc->usb3_generic_phy);
+
 	dwc3_ulpi_exit(dwc);
 
 err4:
@@ -1673,12 +1849,10 @@
 	dwc3_free_event_buffers(dwc);
 
 err2:
-	pm_runtime_allow(&pdev->dev);
-
-err1:
-	pm_runtime_put_sync(&pdev->dev);
-	pm_runtime_disable(&pdev->dev);
-
+	pm_runtime_allow(dev);
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+	pm_runtime_put_noidle(dev);
 disable_clks:
 	clk_bulk_disable_unprepare(dwc->num_clks, dwc->clks);
 assert_reset:
@@ -1696,14 +1870,35 @@
 
 	pm_runtime_get_sync(&pdev->dev);
 
+#ifdef CONFIG_PM_SLEEP
+	if (dwc->is_hibernated) {
+		/*
+		 * As we are about to get removed, wake the controller from
+		 * D3 & hibernation states
+		 */
+		dwc->force_hiber_wake = true;
+		dwc3_gadget_exit_hibernation(dwc);
+		dwc->force_hiber_wake = false;
+	}
+#endif /* CONFIG_PM_SLEEP */
+
 	dwc3_core_exit_mode(dwc);
 	dwc3_debugfs_exit(dwc);
 
 	dwc3_core_exit(dwc);
 	dwc3_ulpi_exit(dwc);
 
+	if (dwc->dwc3_pmu)
+		regulator_disable(dwc->dwc3_pmu);
+
+	pm_runtime_allow(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_put_noidle(&pdev->dev);
+	/*
+	 * HACK: Clear the driver data, which is currently accessed by parent
+	 * glue drivers, before allowing the parent to suspend.
+	 */
+	platform_set_drvdata(pdev, NULL);
 	pm_runtime_set_suspended(&pdev->dev);
 
 	dwc3_free_event_buffers(dwc);
@@ -1744,16 +1939,26 @@
 
 static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
 {
-	unsigned long	flags;
 	u32 reg;
 
+	if (!pm_runtime_suspended(dwc->dev) && !PMSG_IS_AUTO(msg)) {
+		dwc->susphy_state = (dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)) &
+				    DWC3_GUSB2PHYCFG_SUSPHY) ||
+				    (dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0)) &
+				    DWC3_GUSB3PIPECTL_SUSPHY);
+		/*
+		 * TI AM62 platform requires SUSPHY to be
+		 * enabled for system suspend to work.
+		 */
+		if (!dwc->susphy_state)
+			dwc3_enable_susphy(dwc, true);
+	}
+
 	switch (dwc->current_dr_role) {
 	case DWC3_GCTL_PRTCAP_DEVICE:
 		if (pm_runtime_suspended(dwc->dev))
 			break;
-		spin_lock_irqsave(&dwc->lock, flags);
 		dwc3_gadget_suspend(dwc);
-		spin_unlock_irqrestore(&dwc->lock, flags);
 		synchronize_irq(dwc->irq_gadget);
 		dwc3_core_exit(dwc);
 		break;
@@ -1784,9 +1989,7 @@
 			break;
 
 		if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
-			spin_lock_irqsave(&dwc->lock, flags);
 			dwc3_gadget_suspend(dwc);
-			spin_unlock_irqrestore(&dwc->lock, flags);
 			synchronize_irq(dwc->irq_gadget);
 		}
 
@@ -1798,32 +2001,50 @@
 		break;
 	}
 
+	/* Put the core into D3 state */
+	if (dwc->dwc3_pmu) {
+		int ret;
+
+		ret = regulator_disable(dwc->dwc3_pmu);
+		if (ret) {
+			dev_err(dwc->dev,
+				"Failed to disable dwc3_pmu supply\n");
+			return ret;
+		}
+	}
+
 	return 0;
 }
 
 static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
 {
-	unsigned long	flags;
 	int		ret;
 	u32		reg;
 
+	/* Bring core to D0 state */
+	if (dwc->dwc3_pmu) {
+		ret = regulator_enable(dwc->dwc3_pmu);
+		if (ret) {
+			dev_err(dwc->dev, "Failed to enable dwc3_pmu supply\n");
+			return ret;
+		}
+	}
+
 	switch (dwc->current_dr_role) {
 	case DWC3_GCTL_PRTCAP_DEVICE:
 		ret = dwc3_core_init_for_resume(dwc);
 		if (ret)
 			return ret;
 
-		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
-		spin_lock_irqsave(&dwc->lock, flags);
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true);
 		dwc3_gadget_resume(dwc);
-		spin_unlock_irqrestore(&dwc->lock, flags);
 		break;
 	case DWC3_GCTL_PRTCAP_HOST:
 		if (!PMSG_IS_AUTO(msg)) {
 			ret = dwc3_core_init_for_resume(dwc);
 			if (ret)
 				return ret;
-			dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
+			dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, true);
 			break;
 		}
 		/* Restore GUSB2PHYCFG bits that were modified in suspend */
@@ -1848,15 +2069,13 @@
 		if (ret)
 			return ret;
 
-		dwc3_set_prtcap(dwc, dwc->current_dr_role);
+		dwc3_set_prtcap(dwc, dwc->current_dr_role, true);
 
 		dwc3_otg_init(dwc);
 		if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) {
 			dwc3_otg_host_init(dwc);
 		} else if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
-			spin_lock_irqsave(&dwc->lock, flags);
 			dwc3_gadget_resume(dwc);
-			spin_unlock_irqrestore(&dwc->lock, flags);
 		}
 
 		break;
@@ -1865,6 +2084,11 @@
 		break;
 	}
 
+	if (!PMSG_IS_AUTO(msg)) {
+		/* restore SUSPHY state to that before system suspend. */
+		dwc3_enable_susphy(dwc, dwc->susphy_state);
+	}
+
 	return 0;
 }
 
@@ -1914,7 +2138,11 @@
 
 	switch (dwc->current_dr_role) {
 	case DWC3_GCTL_PRTCAP_DEVICE:
-		dwc3_gadget_process_pending_events(dwc);
+		if (dwc->pending_events) {
+			pm_runtime_put(dwc->dev);
+			dwc->pending_events = false;
+			enable_irq(dwc->irq_gadget);
+		}
 		break;
 	case DWC3_GCTL_PRTCAP_HOST:
 	default:
@@ -1955,6 +2183,16 @@
 	struct dwc3	*dwc = dev_get_drvdata(dev);
 	int		ret;
 
+	if (dwc->is_hibernated) {
+		/*
+		 * As we are about to suspend, wake the controller from
+		 * D3 & hibernation states
+		 */
+		dwc->force_hiber_wake = true;
+		dwc3_gadget_exit_hibernation(dwc);
+		dwc->force_hiber_wake = false;
+	}
+
 	ret = dwc3_suspend_common(dwc, PMSG_SUSPEND);
 	if (ret)
 		return ret;
@@ -2001,6 +2239,12 @@
 static const struct dev_pm_ops dwc3_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(dwc3_suspend, dwc3_resume)
 	.complete = dwc3_complete,
+
+	/*
+	 * Runtime suspend halts the controller on disconnection. It relies on
+	 * platforms with custom connection notification to start the controller
+	 * again.
+	 */
 	SET_RUNTIME_PM_OPS(dwc3_runtime_suspend, dwc3_runtime_resume,
 			dwc3_runtime_idle)
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/core.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/core.h
@@ -30,6 +30,7 @@
 #include <linux/ulpi/interface.h>
 
 #include <linux/phy/phy.h>
+#include <../drivers/usb/host/xhci.h>
 
 #include <linux/power_supply.h>
 
@@ -143,7 +144,7 @@
 #define DWC3_GHWPARAMS8		0xc600
 #define DWC3_GUCTL3		0xc60c
 #define DWC3_GFLADJ		0xc630
-#define DWC3_GHWPARAMS9		0xc680
+#define DWC3_GHWPARAMS9		0xc6e0
 
 /* Device Registers */
 #define DWC3_DCFG		0xc700
@@ -171,6 +172,9 @@
 
 /* Bit fields */
 
+/* Global Status Register */
+#define DWC3_GSTS_CUR_MODE			(1 << 0)
+
 /* Global SoC Bus Configuration INCRx Register 0 */
 #define DWC3_GSBUSCFG0_INCR256BRSTENA	(1 << 7) /* INCR256 burst */
 #define DWC3_GSBUSCFG0_INCR128BRSTENA	(1 << 6) /* INCR128 burst */
@@ -203,6 +207,12 @@
 #define DWC3_EVENTQ		7
 #define DWC3_AUXEVENTQ		8
 
+/* Global SoC Bus Configuration Register */
+#define DWC3_GSBUSCFG0_DATRDREQINFO	(0xf << 28)
+#define DWC3_GSBUSCFG0_DESRDREQINFO	(0xf << 24)
+#define DWC3_GSBUSCFG0_DATWRREQINFO	(0xf << 20)
+#define DWC3_GSBUSCFG0_DESWRREQINFO	(0xf << 16)
+
 /* Global RX Threshold Configuration Register */
 #define DWC3_GRXTHRCFG_MAXRXBURSTSIZE(n) (((n) & 0x1f) << 19)
 #define DWC3_GRXTHRCFG_RXPKTCNT(n) (((n) & 0xf) << 24)
@@ -252,14 +262,13 @@
 #define DWC3_GCTL_GBLHIBERNATIONEN	BIT(1)
 #define DWC3_GCTL_DSBLCLKGTNG		BIT(0)
 
-/* Global User Control Register */
-#define DWC3_GUCTL_HSTINAUTORETRY	BIT(14)
-
 /* Global User Control 1 Register */
 #define DWC3_GUCTL1_DEV_DECOUPLE_L1L2_EVT	BIT(31)
 #define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS	BIT(28)
 #define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW		BIT(24)
 #define DWC3_GUCTL1_PARKMODE_DISABLE_SS		BIT(17)
+#define DWC3_GUCTL1_RESUME_OPMODE_HS_HOST	BIT(10)
+#define DWC3_GUCTL1_IPD_QUIRK			BIT(9)
 
 /* Global Status Register */
 #define DWC3_GSTS_OTG_IP	BIT(10)
@@ -386,9 +395,11 @@
 /* Global Frame Length Adjustment Register */
 #define DWC3_GFLADJ_30MHZ_SDBND_SEL		BIT(7)
 #define DWC3_GFLADJ_30MHZ_MASK			0x3f
+#define DWC3_GFLADJ_REFCLK_FLADJ		(0x3fff << 8)
 
 /* Global User Control Register 2 */
 #define DWC3_GUCTL2_RST_ACTBITLATER		BIT(14)
+#define DWC3_GUCTL2_LC_TIMER			BIT(19)
 
 /* Global User Control Register 3 */
 #define DWC3_GUCTL3_SPLITDISABLE		BIT(14)
@@ -431,6 +442,7 @@
 #define DWC3_DCTL_TRGTULST_SS_INACT	(DWC3_DCTL_TRGTULST(6))
 
 /* These apply for core versions 1.94a and later */
+#define DWC3_DCTL_NYET_THRES_MASK	(0xf << 20)
 #define DWC3_DCTL_NYET_THRES(n)		(((n) & 0xf) << 20)
 
 #define DWC3_DCTL_KEEP_CONNECT		BIT(19)
@@ -473,6 +485,7 @@
 
 /* Device Status Register */
 #define DWC3_DSTS_DCNRD			BIT(29)
+#define DWC3_DSTS_SRE			BIT(28)
 
 /* This applies for core versions 1.87a and earlier */
 #define DWC3_DSTS_PWRUPREQ		BIT(24)
@@ -632,6 +645,9 @@
 #define DWC3_OSTS_VBUSVLD		BIT(1)
 #define DWC3_OSTS_CONIDSTS		BIT(0)
 
+/* Stream timer timeout value in millisecs */
+#define STREAM_TIMEOUT_MS		50
+
 /* Structures */
 
 struct dwc3_trb;
@@ -723,6 +739,8 @@
 #define DWC3_EP_FORCE_RESTART_STREAM	BIT(9)
 #define DWC3_EP_FIRST_STREAM_PRIMED	BIT(10)
 #define DWC3_EP_PENDING_CLEAR_STALL	BIT(11)
+#define DWC3_EP_TXFIFO_RESIZED		BIT(12)
+#define DWC3_EP_DELAY_STOP             BIT(13)
 
 	/* This last one is specific to EP0 */
 #define DWC3_EP0_DIR_IN		BIT(31)
@@ -900,6 +918,11 @@
  * @num_trbs: number of TRBs used by this request
  * @needs_extra_trb: true when request needs one extra TRB (either due to ZLP
  *	or unaligned OUT)
+ * @stream_timeout_timer: Some endpoints may go out of sync with host and
+ *	enter into deadlock. For example, stream capable endpoints may enter
+ *	into deadlock where the host waits on gadget to issue ERDY and gadget
+ *	waits for host to issue prime transaction. To avoid such deadlock this
+ *	timer is used.
  * @direction: IN or OUT direction flag
  * @mapped: true when request has been dma-mapped
  */
@@ -930,6 +953,7 @@
 	unsigned int		num_trbs;
 
 	unsigned int		needs_extra_trb:1;
+	struct timer_list	stream_timeout_timer;
 	unsigned int		direction:1;
 	unsigned int		mapped:1;
 };
@@ -970,7 +994,9 @@
  * @regs: base address for our registers
  * @regs_size: address space size
  * @fladj: frame length adjustment
+ * @refclk_fladj: boolean to update GFLADJ_REFCLK_FLADJ field also
  * @irq_gadget: peripheral controller's IRQ number
+ * @otg: pointer to the dwc3_otg structure
  * @otg_irq: IRQ number for OTG IRQs
  * @current_otg_role: current role of operation while using the OTG block
  * @desired_otg_role: desired role of operation while using the OTG block
@@ -1027,6 +1053,7 @@
  * @tx_fifo_resize_max_num: max number of fifos allocated during txfifo resize
  * @hsphy_interface: "utmi" or "ulpi"
  * @connected: true when we're connected to a host, false otherwise
+ * @softconnect: true when gadget connect is called, false when disconnect runs
  * @delayed_status: true when gadget driver asks for delayed status
  * @ep0_bounced: true when we used bounce buffer
  * @ep0_expect_in: true when we expect a DATA IN transfer
@@ -1048,6 +1075,7 @@
  * @usb3_lpm_capable: set if hadrware supports Link Power Management
  * @usb2_lpm_disable: set to disable usb2 lpm for host
  * @usb2_gadget_lpm_disable: set to disable usb2 lpm for gadget
+ * @remote_wakeup: set if host supports Remote Wakeup from Peripheral
  * @disable_scramble_quirk: set if we enable the disable scramble quirk
  * @u2exit_lfps_quirk: set if we enable u2exit lfps quirk
  * @u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
@@ -1068,8 +1096,12 @@
  *			provide a free-running PHY clock.
  * @dis_del_phy_power_chg_quirk: set if we disable delay phy power
  *			change quirk.
+ * @enable_guctl1_ipd_quirk: set if we enable quirk for reducing timing of inter
+ *			packet delay(ipd).
  * @dis_tx_ipgap_linecheck_quirk: set if we disable u2mac linestate
  *			check during HS transmit.
+ * @resume-hs-terminations: Set if we enable quirk for fixing improper crc
+ *			generation after resume from suspend.
  * @parkmode_disable_ss_quirk: set if we need to disable all SuperSpeed
  *			instances in park mode.
  * @tx_de_emphasis_quirk: set if we enable Tx de-emphasis quirk
@@ -1078,8 +1110,12 @@
  *	1	- -3.5dB de-emphasis
  *	2	- No de-emphasis
  *	3	- Reserved
+ * @is_hibernated: true when dwc3 is hibernated; abort processing events
  * @dis_metastability_quirk: set to disable metastability quirk.
  * @dis_split_quirk: set to disable split boundary.
+ * @suspended: set to track suspend event due to U3/L2.
+ * @susphy_state: state of DWC3_GUSB2PHYCFG_SUSPHY + DWC3_GUSB3PIPECTL_SUSPHY
+ *		  before PM suspend.
  * @imod_interval: set the interrupt moderation interval in 250ns
  *			increments or 0 to disable.
  * @max_cfg_eps: current max number of IN eps used across all USB configs.
@@ -1087,6 +1123,13 @@
  *		     address.
  * @num_ep_resized: carries the current number endpoints which have had its tx
  *		    fifo resized.
+ * @debug_root: root debugfs directory for this device to put its files in.
+ * @is_d3: set if the controller is in d3 state
+ * @saved_regs: registers to be saved/restored during hibernation/wakeup events
+ * @irq_wakeup: wakeup IRQ number, triggered when host asks to wakeup from
+ *              hibernation
+ * @force_hiber_wake: flag set when the gadget driver is forcefully triggering
+		a hibernation wakeup event
  */
 struct dwc3 {
 	struct work_struct	drd_work;
@@ -1123,6 +1166,8 @@
 
 	struct reset_control	*reset;
 
+	struct dwc3_otg		*otg;
+
 	struct usb_phy		*usb2_phy;
 	struct usb_phy		*usb3_phy;
 
@@ -1143,12 +1188,14 @@
 	struct extcon_dev	*edev;
 	struct notifier_block	edev_nb;
 	enum usb_phy_interface	hsphy_mode;
+	struct regulator	*dwc3_pmu;
 	struct usb_role_switch	*role_sw;
 	enum usb_dr_mode	role_switch_default_mode;
 
 	struct power_supply	*usb_psy;
 
 	u32			fladj;
+	bool			refclk_fladj;
 	u32			irq_gadget;
 	u32			otg_irq;
 	u32			current_otg_role;
@@ -1192,6 +1239,7 @@
 #define DWC3_REVISION_290A	0x5533290a
 #define DWC3_REVISION_300A	0x5533300a
 #define DWC3_REVISION_310A	0x5533310a
+#define DWC3_REVISION_320A	0x5533320a
 #define DWC3_REVISION_330A	0x5533330a
 
 #define DWC31_REVISION_ANY	0x0
@@ -1246,6 +1294,7 @@
 	const char		*hsphy_interface;
 
 	unsigned		connected:1;
+	unsigned		softconnect:1;
 	unsigned		delayed_status:1;
 	unsigned		ep0_bounced:1;
 	unsigned		ep0_expect_in:1;
@@ -1264,6 +1313,7 @@
 	unsigned		usb2_lpm_disable:1;
 	unsigned		usb2_gadget_lpm_disable:1;
 
+	unsigned                remote_wakeup:1;
 	unsigned		disable_scramble_quirk:1;
 	unsigned		u2exit_lfps_quirk:1;
 	unsigned		u2ss_inp3_quirk:1;
@@ -1280,22 +1330,33 @@
 	unsigned		dis_rxdet_inp3_quirk:1;
 	unsigned		dis_u2_freeclk_exists_quirk:1;
 	unsigned		dis_del_phy_power_chg_quirk:1;
+	unsigned		enable_guctl1_ipd_quirk:1;
 	unsigned		dis_tx_ipgap_linecheck_quirk:1;
+	unsigned		resume_hs_terminations:1;
 	unsigned		parkmode_disable_ss_quirk:1;
 
 	unsigned		tx_de_emphasis_quirk:1;
 	unsigned		tx_de_emphasis:2;
+	unsigned		is_hibernated:1;
 
 	unsigned		dis_metastability_quirk:1;
+	unsigned		mask_phy_rst:1;
 
 	unsigned		dis_split_quirk:1;
 	unsigned		async_callbacks:1;
+	unsigned		suspended:1;
+	unsigned		susphy_state:1;
 
 	u16			imod_interval;
 
 	int			max_cfg_eps;
 	int			last_fifo_depth;
 	int			num_ep_resized;
+	struct dentry		*debug_root;
+	bool			is_d3;
+	u32			*saved_regs;
+	u32			irq_wakeup;
+	bool			force_hiber_wake;
 };
 
 #define INCRX_BURST_MODE 0
@@ -1460,10 +1521,13 @@
 #define DWC3_HAS_OTG			BIT(3)
 
 /* prototypes */
-void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode);
+void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode, bool ignore_susphy);
 void dwc3_set_mode(struct dwc3 *dwc, u32 mode);
 u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type);
 
+typedef void (*dwc3_wakeup_t)(struct device *dev, bool wakeup);
+void dwc3_host_wakeup_register(dwc3_wakeup_t func);
+
 #define DWC3_IP_IS(_ip)							\
 	(dwc->ip == _ip##_IP)
 
@@ -1507,7 +1571,11 @@
 int dwc3_event_buffers_setup(struct dwc3 *dwc);
 void dwc3_event_buffers_cleanup(struct dwc3 *dwc);
 
-#if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
+int dwc3_core_soft_reset(struct dwc3 *dwc);
+void dwc3_enable_susphy(struct dwc3 *dwc, bool enable);
+
+#if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)\
+	 || IS_ENABLED(CONFIG_USB_DWC3_OTG)
 int dwc3_host_init(struct dwc3 *dwc);
 void dwc3_host_exit(struct dwc3 *dwc);
 #else
@@ -1517,7 +1585,8 @@
 { }
 #endif
 
-#if IS_ENABLED(CONFIG_USB_DWC3_GADGET) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
+#if IS_ENABLED(CONFIG_USB_DWC3_GADGET) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)\
+	 || IS_ENABLED(CONFIG_USB_DWC3_OTG)
 int dwc3_gadget_init(struct dwc3 *dwc);
 void dwc3_gadget_exit(struct dwc3 *dwc);
 int dwc3_gadget_set_test_mode(struct dwc3 *dwc, int mode);
@@ -1528,6 +1597,7 @@
 int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
 		u32 param);
 void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
+int dwc3_core_init(struct dwc3 *dwc);
 #else
 static inline int dwc3_gadget_init(struct dwc3 *dwc)
 { return 0; }
@@ -1551,11 +1621,19 @@
 { }
 #endif
 
+#if IS_ENABLED(CONFIG_USB_DWC3_OTG) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
+void dwc3_otg_init(struct dwc3 *dwc);
+void dwc3_otg_exit(struct dwc3 *dwc);
+#else
+static inline void dwc3_otg_init(struct dwc3 *dwc)
+{ }
+static inline void dwc3_otg_exit(struct dwc3 *dwc)
+{ }
+#endif
+
 #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
 int dwc3_drd_init(struct dwc3 *dwc);
 void dwc3_drd_exit(struct dwc3 *dwc);
-void dwc3_otg_init(struct dwc3 *dwc);
-void dwc3_otg_exit(struct dwc3 *dwc);
 void dwc3_otg_update(struct dwc3 *dwc, bool ignore_idstatus);
 void dwc3_otg_host_init(struct dwc3 *dwc);
 #else
@@ -1563,10 +1641,6 @@
 { return 0; }
 static inline void dwc3_drd_exit(struct dwc3 *dwc)
 { }
-static inline void dwc3_otg_init(struct dwc3 *dwc)
-{ }
-static inline void dwc3_otg_exit(struct dwc3 *dwc)
-{ }
 static inline void dwc3_otg_update(struct dwc3 *dwc, bool ignore_idstatus)
 { }
 static inline void dwc3_otg_host_init(struct dwc3 *dwc)
@@ -1577,7 +1651,6 @@
 #if !IS_ENABLED(CONFIG_USB_DWC3_HOST)
 int dwc3_gadget_suspend(struct dwc3 *dwc);
 int dwc3_gadget_resume(struct dwc3 *dwc);
-void dwc3_gadget_process_pending_events(struct dwc3 *dwc);
 #else
 static inline int dwc3_gadget_suspend(struct dwc3 *dwc)
 {
@@ -1589,9 +1662,6 @@
 	return 0;
 }
 
-static inline void dwc3_gadget_process_pending_events(struct dwc3 *dwc)
-{
-}
 #endif /* !IS_ENABLED(CONFIG_USB_DWC3_HOST) */
 
 #if IS_ENABLED(CONFIG_USB_DWC3_ULPI)
@@ -1603,5 +1673,8 @@
 static inline void dwc3_ulpi_exit(struct dwc3 *dwc)
 { }
 #endif
+int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length);
+void dwc3_free_event_buffers(struct dwc3 *dwc);
+int dwc3_event_buffers_setup(struct dwc3 *dwc);
 
 #endif /* __DRIVERS_USB_DWC3_CORE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/debug.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/debug.h
@@ -414,11 +414,14 @@
 
 #ifdef CONFIG_DEBUG_FS
 extern void dwc3_debugfs_create_endpoint_dir(struct dwc3_ep *dep);
+extern void dwc3_debugfs_remove_endpoint_dir(struct dwc3_ep *dep);
 extern void dwc3_debugfs_init(struct dwc3 *d);
 extern void dwc3_debugfs_exit(struct dwc3 *d);
 #else
 static inline void dwc3_debugfs_create_endpoint_dir(struct dwc3_ep *dep)
 {  }
+static inline void dwc3_debugfs_remove_endpoint_dir(struct dwc3_ep *dep)
+{  }
 static inline void dwc3_debugfs_init(struct dwc3 *d)
 {  }
 static inline void dwc3_debugfs_exit(struct dwc3 *d)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/debugfs.c
@@ -327,6 +327,11 @@
 	unsigned int		current_mode;
 	unsigned long		flags;
 	u32			reg;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	reg = dwc3_readl(dwc->regs, DWC3_GSTS);
@@ -345,6 +350,8 @@
 	}
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -390,6 +397,11 @@
 	struct dwc3		*dwc = s->private;
 	unsigned long		flags;
 	u32			reg;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	reg = dwc3_readl(dwc->regs, DWC3_GCTL);
@@ -409,6 +421,8 @@
 		seq_printf(s, "UNKNOWN %08x\n", DWC3_GCTL_PRTCAP(reg));
 	}
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -458,6 +472,11 @@
 	struct dwc3		*dwc = s->private;
 	unsigned long		flags;
 	u32			reg;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
@@ -488,6 +507,8 @@
 		seq_printf(s, "UNKNOWN %d\n", reg);
 	}
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -504,6 +525,7 @@
 	unsigned long		flags;
 	u32			testmode = 0;
 	char			buf[32];
+	int			ret;
 
 	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
 		return -EFAULT;
@@ -521,10 +543,16 @@
 	else
 		testmode = 0;
 
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
+
 	spin_lock_irqsave(&dwc->lock, flags);
 	dwc3_gadget_set_test_mode(dwc, testmode);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return count;
 }
 
@@ -543,12 +571,18 @@
 	enum dwc3_link_state	state;
 	u32			reg;
 	u8			speed;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	reg = dwc3_readl(dwc->regs, DWC3_GSTS);
 	if (DWC3_GSTS_CURMOD(reg) != DWC3_GSTS_CURMOD_DEVICE) {
 		seq_puts(s, "Not available\n");
 		spin_unlock_irqrestore(&dwc->lock, flags);
+		pm_runtime_put_sync(dwc->dev);
 		return 0;
 	}
 
@@ -561,6 +595,8 @@
 		   dwc3_gadget_hs_link_string(state));
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -579,6 +615,7 @@
 	char			buf[32];
 	u32			reg;
 	u8			speed;
+	int			ret;
 
 	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
 		return -EFAULT;
@@ -598,10 +635,15 @@
 	else
 		return -EINVAL;
 
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
+
 	spin_lock_irqsave(&dwc->lock, flags);
 	reg = dwc3_readl(dwc->regs, DWC3_GSTS);
 	if (DWC3_GSTS_CURMOD(reg) != DWC3_GSTS_CURMOD_DEVICE) {
 		spin_unlock_irqrestore(&dwc->lock, flags);
+		pm_runtime_put_sync(dwc->dev);
 		return -EINVAL;
 	}
 
@@ -611,12 +653,15 @@
 	if (speed < DWC3_DSTS_SUPERSPEED &&
 	    state != DWC3_LINK_STATE_RECOV) {
 		spin_unlock_irqrestore(&dwc->lock, flags);
+		pm_runtime_put_sync(dwc->dev);
 		return -EINVAL;
 	}
 
 	dwc3_gadget_set_link_state(dwc, state);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return count;
 }
 
@@ -628,6 +673,53 @@
 	.release		= single_release,
 };
 
+static int dwc3_hiber_enable_show(struct seq_file *s, void *unused)
+{
+	struct dwc3		*dwc = s->private;
+
+	seq_printf(s, "%s\n", (dwc->has_hibernation ? "Enabled" : "Disabled"));
+
+	return 0;
+}
+
+static int dwc3_hiber_enable_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, dwc3_hiber_enable_show, inode->i_private);
+}
+
+static ssize_t dwc3_hiber_enable_write(struct file *file,
+				       const char __user *ubuf,
+				       size_t count, loff_t *ppos)
+{
+	struct seq_file		*s = file->private_data;
+	struct dwc3		*dwc = s->private;
+	char			buf[32];
+
+	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
+		return -EFAULT;
+
+	/* Enable hibernation feature */
+	if (!strncmp(buf, "Enable", 6)) {
+		dwc3_gadget_exit(dwc);
+		dwc->has_hibernation = 1;
+		dwc3_gadget_init(dwc);
+	} else if (!strncmp(buf, "Disable", 6)) {
+		dwc3_gadget_exit(dwc);
+		dwc->has_hibernation = 0;
+		dwc3_gadget_init(dwc);
+	} else {
+		return -EINVAL;
+	}
+
+	return count;
+}
+
+static const struct file_operations dwc3_hiber_enable_fops = {
+	.open			= dwc3_hiber_enable_open,
+	.write			= dwc3_hiber_enable_write,
+	.read			= seq_read,
+};
+
 struct dwc3_ep_file_map {
 	const char name[25];
 	const struct file_operations *const fops;
@@ -640,6 +732,11 @@
 	unsigned long		flags;
 	u32			mdwidth;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_TXFIFO);
@@ -652,6 +749,8 @@
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -662,6 +761,11 @@
 	unsigned long		flags;
 	u32			mdwidth;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_RXFIFO);
@@ -674,6 +778,8 @@
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -683,12 +789,19 @@
 	struct dwc3		*dwc = dep->dwc;
 	unsigned long		flags;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_TXREQQ);
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -698,12 +811,19 @@
 	struct dwc3		*dwc = dep->dwc;
 	unsigned long		flags;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_RXREQQ);
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -713,12 +833,19 @@
 	struct dwc3		*dwc = dep->dwc;
 	unsigned long		flags;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_RXINFOQ);
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -728,12 +855,19 @@
 	struct dwc3		*dwc = dep->dwc;
 	unsigned long		flags;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_DESCFETCHQ);
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -743,12 +877,19 @@
 	struct dwc3		*dwc = dep->dwc;
 	unsigned long		flags;
 	u32			val;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	val = dwc3_core_fifo_space(dep, DWC3_EVENTQ);
 	seq_printf(s, "%u\n", val);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -793,6 +934,11 @@
 	struct dwc3		*dwc = dep->dwc;
 	unsigned long		flags;
 	int			i;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	if (dep->number <= 1) {
@@ -822,6 +968,8 @@
 out:
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -834,6 +982,11 @@
 	u32			lower_32_bits;
 	u32			upper_32_bits;
 	u32			reg;
+	int			ret;
+
+	ret = pm_runtime_resume_and_get(dwc->dev);
+	if (ret < 0)
+		return ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	reg = DWC3_GDBGLSPMUX_EPSELECT(dep->number);
@@ -846,6 +999,8 @@
 	seq_printf(s, "0x%016llx\n", ep_info);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
+	pm_runtime_put_sync(dwc->dev);
+
 	return 0;
 }
 
@@ -873,27 +1028,23 @@
 	{ "GDBGEPINFO", &dwc3_ep_info_register_fops, },
 };
 
-static void dwc3_debugfs_create_endpoint_files(struct dwc3_ep *dep,
-		struct dentry *parent)
+void dwc3_debugfs_create_endpoint_dir(struct dwc3_ep *dep)
 {
+	struct dentry		*dir;
 	int			i;
 
+	dir = debugfs_create_dir(dep->name, dep->dwc->debug_root);
 	for (i = 0; i < ARRAY_SIZE(dwc3_ep_file_map); i++) {
 		const struct file_operations *fops = dwc3_ep_file_map[i].fops;
 		const char *name = dwc3_ep_file_map[i].name;
 
-		debugfs_create_file(name, 0444, parent, dep, fops);
+		debugfs_create_file(name, 0444, dir, dep, fops);
 	}
 }
 
-void dwc3_debugfs_create_endpoint_dir(struct dwc3_ep *dep)
+void dwc3_debugfs_remove_endpoint_dir(struct dwc3_ep *dep)
 {
-	struct dentry		*dir;
-	struct dentry		*root;
-
-	root = debugfs_lookup(dev_name(dep->dwc->dev), usb_debug_root);
-	dir = debugfs_create_dir(dep->name, root);
-	dwc3_debugfs_create_endpoint_files(dep, dir);
+	debugfs_lookup_and_remove(dep->name, dep->dwc->debug_root);
 }
 
 void dwc3_debugfs_init(struct dwc3 *dwc)
@@ -909,8 +1060,10 @@
 	dwc->regset->regs = dwc3_regs;
 	dwc->regset->nregs = ARRAY_SIZE(dwc3_regs);
 	dwc->regset->base = dwc->regs - DWC3_GLOBALS_REGS_START;
+	dwc->regset->dev = dwc->dev;
 
 	root = debugfs_create_dir(dev_name(dwc->dev), usb_debug_root);
+	dwc->debug_root = root;
 	debugfs_create_regset32("regdump", 0444, root, dwc->regset);
 	debugfs_create_file("lsp_dump", 0644, root, dwc, &dwc3_lsp_fops);
 
@@ -924,11 +1077,13 @@
 				&dwc3_testmode_fops);
 		debugfs_create_file("link_state", 0644, root, dwc,
 				    &dwc3_link_state_fops);
+		debugfs_create_file("hiber_enable", S_IRUGO | S_IWUSR, root,
+				    dwc, &dwc3_hiber_enable_fops);
 	}
 }
 
 void dwc3_debugfs_exit(struct dwc3 *dwc)
 {
-	debugfs_remove(debugfs_lookup(dev_name(dwc->dev), usb_debug_root));
+	debugfs_lookup_and_remove(dev_name(dwc->dev), usb_debug_root);
 	kfree(dwc->regset);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/drd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/drd.c
@@ -173,7 +173,7 @@
 	 * block "Initialize GCTL for OTG operation".
 	 */
 	/* GCTL.PrtCapDir=2'b11 */
-	dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG);
+	dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true);
 	/* GUSB2PHYCFG0.SusPHY=0 */
 	reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
 	reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
@@ -443,7 +443,7 @@
 	struct device *dev = dwc->dev;
 	struct device_node *np_phy;
 	struct extcon_dev *edev = NULL;
-	const char *name;
+	const char *name = "";
 
 	if (device_property_read_bool(dev, "extcon"))
 		return extcon_get_edev_by_phandle(dev, 0);
@@ -454,13 +454,8 @@
 	 * This device property is for kernel internal use only and
 	 * is expected to be set by the glue code.
 	 */
-	if (device_property_read_string(dev, "linux,extcon-name", &name) == 0) {
-		edev = extcon_get_extcon_dev(name);
-		if (!edev)
-			return ERR_PTR(-EPROBE_DEFER);
-
-		return edev;
-	}
+	if (device_property_read_string(dev, "linux,extcon-name", &name) == 0)
+		return extcon_get_extcon_dev(name);
 
 	/*
 	 * Try to get an extcon device from the USB PHY controller's "port"
@@ -550,6 +545,7 @@
 		dwc->role_switch_default_mode = USB_DR_MODE_PERIPHERAL;
 		mode = DWC3_GCTL_PRTCAP_DEVICE;
 	}
+	dwc3_set_mode(dwc, mode);
 
 	dwc3_role_switch.fwnode = dev_fwnode(dwc->dev);
 	dwc3_role_switch.set = dwc3_usb_role_switch_set;
@@ -559,7 +555,6 @@
 	if (IS_ERR(dwc->role_sw))
 		return PTR_ERR(dwc->role_sw);
 
-	dwc3_set_mode(dwc, mode);
 	return 0;
 }
 #else
@@ -571,16 +566,15 @@
 {
 	int ret, irq;
 
+	if (ROLE_SWITCH &&
+	    device_property_read_bool(dwc->dev, "usb-role-switch"))
+		return dwc3_setup_role_switch(dwc);
+
 	dwc->edev = dwc3_get_extcon(dwc);
 	if (IS_ERR(dwc->edev))
 		return PTR_ERR(dwc->edev);
 
-	if (ROLE_SWITCH &&
-	    device_property_read_bool(dwc->dev, "usb-role-switch")) {
-		ret = dwc3_setup_role_switch(dwc);
-		if (ret < 0)
-			return ret;
-	} else if (dwc->edev) {
+	if (dwc->edev) {
 		dwc->edev_nb.notifier_call = dwc3_drd_notifier;
 		ret = extcon_register_notifier(dwc->edev, EXTCON_USB_HOST,
 					       &dwc->edev_nb);
@@ -591,7 +585,7 @@
 
 		dwc3_drd_update(dwc);
 	} else {
-		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG);
+		dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true);
 
 		/* use OTG block to get ID event */
 		irq = dwc3_otg_get_irq(dwc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-exynos.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-exynos.c
@@ -37,15 +37,6 @@
 	struct regulator	*vdd10;
 };
 
-static int dwc3_exynos_remove_child(struct device *dev, void *unused)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-
-	platform_device_unregister(pdev);
-
-	return 0;
-}
-
 static int dwc3_exynos_probe(struct platform_device *pdev)
 {
 	struct dwc3_exynos	*exynos;
@@ -142,7 +133,7 @@
 	struct dwc3_exynos	*exynos = platform_get_drvdata(pdev);
 	int i;
 
-	device_for_each_child(&pdev->dev, NULL, dwc3_exynos_remove_child);
+	of_platform_depopulate(&pdev->dev);
 
 	for (i = exynos->num_clks - 1; i >= 0; i--)
 		clk_disable_unprepare(exynos->clks[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-meson-g12a.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-meson-g12a.c
@@ -755,16 +755,16 @@
 
 	ret = dwc3_meson_g12a_get_phys(priv);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	ret = priv->drvdata->setup_regmaps(priv, base);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	if (priv->vbus) {
 		ret = regulator_enable(priv->vbus);
 		if (ret)
-			goto err_disable_clks;
+			goto err_rearm;
 	}
 
 	/* Get dr_mode */
@@ -805,7 +805,7 @@
 
 	ret = dwc3_meson_g12a_otg_init(pdev, priv);
 	if (ret)
-		goto err_phys_power;
+		goto err_plat_depopulate;
 
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
@@ -813,6 +813,9 @@
 
 	return 0;
 
+err_plat_depopulate:
+	of_platform_depopulate(dev);
+
 err_phys_power:
 	for (i = 0 ; i < PHY_COUNT ; ++i)
 		phy_power_off(priv->phys[i]);
@@ -825,6 +828,9 @@
 	if (priv->vbus)
 		regulator_disable(priv->vbus);
 
+err_rearm:
+	reset_control_rearm(priv->reset);
+
 err_disable_clks:
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
@@ -852,6 +858,8 @@
 	pm_runtime_put_noidle(dev);
 	pm_runtime_set_suspended(dev);
 
+	reset_control_rearm(priv->reset);
+
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
 
@@ -892,7 +900,7 @@
 		phy_exit(priv->phys[i]);
 	}
 
-	reset_control_assert(priv->reset);
+	reset_control_rearm(priv->reset);
 
 	return 0;
 }
@@ -902,7 +910,9 @@
 	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
 	int i, ret;
 
-	reset_control_deassert(priv->reset);
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;
 
 	ret = priv->drvdata->usb_init(priv);
 	if (ret)
@@ -927,6 +937,12 @@
 		if (ret)
 			return ret;
 	}
+
+	if (priv->drvdata->usb_post_init) {
+		ret = priv->drvdata->usb_post_init(priv);
+		if (ret)
+			return ret;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-omap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-omap.c
@@ -242,7 +242,7 @@
 		break;
 
 	case OMAP_DWC3_ID_FLOAT:
-		if (omap->vbus_reg)
+		if (omap->vbus_reg && regulator_is_enabled(omap->vbus_reg))
 			regulator_disable(omap->vbus_reg);
 		val = dwc3_omap_read_utmi_ctrl(omap);
 		val |= USBOTGSS_UTMI_OTG_CTRL_IDDIG;
@@ -522,11 +522,13 @@
 	if (ret) {
 		dev_err(dev, "failed to request IRQ #%d --> %d\n",
 			omap->irq, ret);
-		goto err1;
+		goto err2;
 	}
 	dwc3_omap_enable_irqs(omap);
 	return 0;
 
+err2:
+	of_platform_depopulate(dev);
 err1:
 	pm_runtime_put_sync(dev);
 	pm_runtime_disable(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-pci.c
@@ -43,6 +43,12 @@
 #define PCI_DEVICE_ID_INTEL_ADLP		0x51ee
 #define PCI_DEVICE_ID_INTEL_ADLM		0x54ee
 #define PCI_DEVICE_ID_INTEL_ADLS		0x7ae1
+#define PCI_DEVICE_ID_INTEL_RPL			0xa70e
+#define PCI_DEVICE_ID_INTEL_RPLS		0x7a61
+#define PCI_DEVICE_ID_INTEL_MTLM		0x7eb1
+#define PCI_DEVICE_ID_INTEL_MTLP		0x7ec1
+#define PCI_DEVICE_ID_INTEL_MTLS		0x7f6f
+#define PCI_DEVICE_ID_INTEL_MTL			0x7e7e
 #define PCI_DEVICE_ID_INTEL_TGL			0x9a15
 #define PCI_DEVICE_ID_AMD_MR			0x163a
 
@@ -85,8 +91,8 @@
 static struct gpiod_lookup_table platform_bytcr_gpios = {
 	.dev_id		= "0000:00:16.0",
 	.table		= {
-		GPIO_LOOKUP("INT33FC:00", 54, "reset", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("INT33FC:02", 14, "cs", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("INT33FC:00", 54, "cs", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("INT33FC:02", 14, "reset", GPIO_ACTIVE_HIGH),
 		{}
 	},
 };
@@ -119,6 +125,13 @@
 	{}
 };
 
+static const struct property_entry dwc3_pci_intel_byt_properties[] = {
+	PROPERTY_ENTRY_STRING("dr_mode", "peripheral"),
+	PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"),
+	PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
+	{}
+};
+
 static const struct property_entry dwc3_pci_mrfld_properties[] = {
 	PROPERTY_ENTRY_STRING("dr_mode", "otg"),
 	PROPERTY_ENTRY_STRING("linux,extcon-name", "mrfld_bcove_pwrsrc"),
@@ -161,6 +174,10 @@
 	.properties = dwc3_pci_intel_properties,
 };
 
+static const struct software_node dwc3_pci_intel_byt_swnode = {
+	.properties = dwc3_pci_intel_byt_properties,
+};
+
 static const struct software_node dwc3_pci_intel_mrfld_swnode = {
 	.properties = dwc3_pci_mrfld_properties,
 };
@@ -173,7 +190,8 @@
 	.properties = dwc3_pci_mr_properties,
 };
 
-static int dwc3_pci_quirks(struct dwc3_pci *dwc)
+static int dwc3_pci_quirks(struct dwc3_pci *dwc,
+			   const struct software_node *swnode)
 {
 	struct pci_dev			*pdev = dwc->pci;
 
@@ -201,10 +219,12 @@
 
 			/*
 			 * A lot of BYT devices lack ACPI resource entries for
-			 * the GPIOs, add a fallback mapping to the reference
+			 * the GPIOs. If the ACPI entry for the GPIO controller
+			 * is present add a fallback mapping to the reference
 			 * design GPIOs which all boards seem to use.
 			 */
-			gpiod_add_lookup_table(&platform_bytcr_gpios);
+			if (acpi_dev_present("INT33FC", NULL, -1))
+				gpiod_add_lookup_table(&platform_bytcr_gpios);
 
 			/*
 			 * These GPIOs will turn on the USB2 PHY. Note that we have to
@@ -230,7 +250,7 @@
 		}
 	}
 
-	return 0;
+	return device_add_software_node(&dwc->dwc3->dev, swnode);
 }
 
 #ifdef CONFIG_PM
@@ -241,7 +261,7 @@
 	int ret;
 
 	ret = pm_runtime_get_sync(&dwc3->dev);
-	if (ret) {
+	if (ret < 0) {
 		pm_runtime_put_sync_autosuspend(&dwc3->dev);
 		return;
 	}
@@ -295,11 +315,7 @@
 	dwc->dwc3->dev.parent = dev;
 	ACPI_COMPANION_SET(&dwc->dwc3->dev, ACPI_COMPANION(dev));
 
-	ret = device_add_software_node(&dwc->dwc3->dev, (void *)id->driver_data);
-	if (ret < 0)
-		goto err;
-
-	ret = dwc3_pci_quirks(dwc);
+	ret = dwc3_pci_quirks(dwc, (void *)id->driver_data);
 	if (ret)
 		goto err;
 
@@ -344,7 +360,7 @@
 	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
 
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_BYT),
-	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+	  (kernel_ulong_t) &dwc3_pci_intel_byt_swnode, },
 
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MRFLD),
 	  (kernel_ulong_t) &dwc3_pci_intel_mrfld_swnode, },
@@ -409,6 +425,24 @@
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ADLS),
 	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
 
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_RPL),
+	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_RPLS),
+	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTLM),
+	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTLP),
+	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTLS),
+	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MTL),
+	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
+
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_TGL),
 	  (kernel_ulong_t) &dwc3_pci_intel_swnode, },
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-qcom.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-qcom.c
@@ -258,7 +258,8 @@
 	if (IS_ERR(qcom->icc_path_apps)) {
 		dev_err(dev, "failed to get apps-usb path: %ld\n",
 				PTR_ERR(qcom->icc_path_apps));
-		return PTR_ERR(qcom->icc_path_apps);
+		ret = PTR_ERR(qcom->icc_path_apps);
+		goto put_path_ddr;
 	}
 
 	if (usb_get_maximum_speed(&qcom->dwc3->dev) >= USB_SPEED_SUPER ||
@@ -271,17 +272,23 @@
 
 	if (ret) {
 		dev_err(dev, "failed to set bandwidth for usb-ddr path: %d\n", ret);
-		return ret;
+		goto put_path_apps;
 	}
 
 	ret = icc_set_bw(qcom->icc_path_apps,
 		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
 	if (ret) {
 		dev_err(dev, "failed to set bandwidth for apps-usb path: %d\n", ret);
-		return ret;
+		goto put_path_apps;
 	}
 
 	return 0;
+
+put_path_apps:
+	icc_put(qcom->icc_path_apps);
+put_path_ddr:
+	icc_put(qcom->icc_path_ddr);
+	return ret;
 }
 
 /**
@@ -296,6 +303,23 @@
 	icc_put(qcom->icc_path_apps);
 }
 
+/* Only usable in contexts where the role can not change. */
+static bool dwc3_qcom_is_host(struct dwc3_qcom *qcom)
+{
+	struct dwc3 *dwc;
+
+	/*
+	 * FIXME: Fix this layering violation.
+	 */
+	dwc = platform_get_drvdata(qcom->dwc3);
+
+	/* Core driver may not have probed yet. */
+	if (!dwc)
+		return false;
+
+	return dwc->xhci;
+}
+
 static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
 	if (qcom->hs_phy_irq) {
@@ -411,7 +435,11 @@
 	if (qcom->pm_suspended)
 		return IRQ_HANDLED;
 
-	if (dwc->xhci)
+	/*
+	 * This is safe as role switching is done from a freezable workqueue
+	 * and the wakeup interrupts are disabled as part of resume.
+	 */
+	if (dwc3_qcom_is_host(qcom))
 		pm_runtime_resume(&dwc->xhci->dev);
 
 	return IRQ_HANDLED;
@@ -443,9 +471,9 @@
 	int ret;
 
 	if (np)
-		ret = platform_get_irq_byname(pdev_irq, name);
+		ret = platform_get_irq_byname_optional(pdev_irq, name);
 	else
-		ret = platform_get_irq(pdev_irq, num);
+		ret = platform_get_irq_optional(pdev_irq, num);
 
 	return ret;
 }
@@ -464,7 +492,7 @@
 		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT,
 					"qcom_dwc3 HS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "hs_phy_irq failed: %d\n", ret);
@@ -479,7 +507,7 @@
 		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT,
 					"qcom_dwc3 DP_HS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "dp_hs_phy_irq failed: %d\n", ret);
@@ -494,7 +522,7 @@
 		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT,
 					"qcom_dwc3 DM_HS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "dm_hs_phy_irq failed: %d\n", ret);
@@ -509,7 +537,7 @@
 		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT,
 					"qcom_dwc3 SS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "ss_phy_irq failed: %d\n", ret);
@@ -598,8 +626,10 @@
 	qcom->dwc3->dev.coherent_dma_mask = dev->coherent_dma_mask;
 
 	child_res = kcalloc(2, sizeof(*child_res), GFP_KERNEL);
-	if (!child_res)
+	if (!child_res) {
+		platform_device_put(qcom->dwc3);
 		return -ENOMEM;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
@@ -637,9 +667,13 @@
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add device\n");
 		device_remove_software_node(&qcom->dwc3->dev);
+		goto out;
 	}
+	kfree(child_res);
+	return 0;
 
 out:
+	platform_device_put(qcom->dwc3);
 	kfree(child_res);
 	return ret;
 }
@@ -649,7 +683,6 @@
 	struct dwc3_qcom	*qcom = platform_get_drvdata(pdev);
 	struct device_node	*np = pdev->dev.of_node, *dwc3_np;
 	struct device		*dev = &pdev->dev;
-	struct property		*prop;
 	int			ret;
 
 	dwc3_np = of_get_compatible_child(np, "snps,dwc3");
@@ -658,20 +691,6 @@
 		return -ENODEV;
 	}
 
-	prop = devm_kzalloc(dev, sizeof(*prop), GFP_KERNEL);
-	if (!prop) {
-		ret = -ENOMEM;
-		dev_err(dev, "unable to allocate memory for property\n");
-		goto node_put;
-	}
-
-	prop->name = "tx-fifo-resize";
-	ret = of_add_property(dwc3_np, prop);
-	if (ret) {
-		dev_err(dev, "unable to add property\n");
-		goto node_put;
-	}
-
 	ret = of_platform_populate(np, NULL, NULL, dev);
 	if (ret) {
 		dev_err(dev, "failed to register dwc3 core - %d\n", ret);
@@ -682,6 +701,7 @@
 	if (!qcom->dwc3) {
 		ret = -ENODEV;
 		dev_err(dev, "failed to get dwc3 platform device\n");
+		of_platform_depopulate(dev);
 	}
 
 node_put:
@@ -690,9 +710,9 @@
 	return ret;
 }
 
-static struct platform_device *
-dwc3_qcom_create_urs_usb_platdev(struct device *dev)
+static struct platform_device *dwc3_qcom_create_urs_usb_platdev(struct device *dev)
 {
+	struct platform_device *urs_usb = NULL;
 	struct fwnode_handle *fwh;
 	struct acpi_device *adev;
 	char name[8];
@@ -712,9 +732,26 @@
 
 	adev = to_acpi_device_node(fwh);
 	if (!adev)
-		return NULL;
+		goto err_put_handle;
+
+	urs_usb = acpi_create_platform_device(adev, NULL);
+	if (IS_ERR_OR_NULL(urs_usb))
+		goto err_put_handle;
+
+	return urs_usb;
+
+err_put_handle:
+	fwnode_handle_put(fwh);
 
-	return acpi_create_platform_device(adev, NULL);
+	return urs_usb;
+}
+
+static void dwc3_qcom_destroy_urs_usb_platdev(struct platform_device *urs_usb)
+{
+	struct fwnode_handle *fwh = urs_usb->dev.fwnode;
+
+	platform_device_unregister(urs_usb);
+	fwnode_handle_put(fwh);
 }
 
 static int dwc3_qcom_probe(struct platform_device *pdev)
@@ -723,6 +760,7 @@
 	struct device		*dev = &pdev->dev;
 	struct dwc3_qcom	*qcom;
 	struct resource		*res, *parent_res = NULL;
+	struct resource		local_res;
 	int			ret, i;
 	bool			ignore_pipe_clk;
 
@@ -773,9 +811,8 @@
 	if (np) {
 		parent_res = res;
 	} else {
-		parent_res = kmemdup(res, sizeof(struct resource), GFP_KERNEL);
-		if (!parent_res)
-			return -ENOMEM;
+		memcpy(&local_res, res, sizeof(struct resource));
+		parent_res = &local_res;
 
 		parent_res->start = res->start +
 			qcom->acpi_pdata->qscratch_base_offset;
@@ -784,9 +821,13 @@
 
 		if (qcom->acpi_pdata->is_urs) {
 			qcom->urs_usb = dwc3_qcom_create_urs_usb_platdev(dev);
-			if (!qcom->urs_usb) {
+			if (IS_ERR_OR_NULL(qcom->urs_usb)) {
 				dev_err(dev, "failed to create URS USB platdev\n");
-				return -ENODEV;
+				if (!qcom->urs_usb)
+					ret = -ENODEV;
+				else
+					ret = PTR_ERR(qcom->urs_usb);
+				goto clk_disable;
 			}
 		}
 	}
@@ -794,13 +835,13 @@
 	qcom->qscratch_base = devm_ioremap_resource(dev, parent_res);
 	if (IS_ERR(qcom->qscratch_base)) {
 		ret = PTR_ERR(qcom->qscratch_base);
-		goto clk_disable;
+		goto free_urs;
 	}
 
 	ret = dwc3_qcom_setup_irq(pdev);
 	if (ret) {
 		dev_err(dev, "failed to setup IRQs, err=%d\n", ret);
-		goto clk_disable;
+		goto free_urs;
 	}
 
 	/*
@@ -819,7 +860,7 @@
 
 	if (ret) {
 		dev_err(dev, "failed to register DWC3 Core, err=%d\n", ret);
-		goto depopulate;
+		goto free_urs;
 	}
 
 	ret = dwc3_qcom_interconnect_init(qcom);
@@ -829,7 +870,7 @@
 	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
 
 	/* enable vbus override for device mode */
-	if (qcom->mode == USB_DR_MODE_PERIPHERAL)
+	if (qcom->mode != USB_DR_MODE_HOST)
 		dwc3_qcom_vbus_override_enable(qcom, true);
 
 	/* register extcon to override sw_vbus on Vbus change later */
@@ -848,10 +889,16 @@
 interconnect_exit:
 	dwc3_qcom_interconnect_exit(qcom);
 depopulate:
-	if (np)
+	if (np) {
 		of_platform_depopulate(&pdev->dev);
-	else
-		platform_device_put(pdev);
+	} else {
+		device_remove_software_node(&qcom->dwc3->dev);
+		platform_device_del(qcom->dwc3);
+	}
+	platform_device_put(qcom->dwc3);
+free_urs:
+	if (qcom->urs_usb)
+		dwc3_qcom_destroy_urs_usb_platdev(qcom->urs_usb);
 clk_disable:
 	for (i = qcom->num_clocks - 1; i >= 0; i--) {
 		clk_disable_unprepare(qcom->clks[i]);
@@ -866,11 +913,20 @@
 static int dwc3_qcom_remove(struct platform_device *pdev)
 {
 	struct dwc3_qcom *qcom = platform_get_drvdata(pdev);
+	struct device_node *np = pdev->dev.of_node;
 	struct device *dev = &pdev->dev;
 	int i;
 
-	device_remove_software_node(&qcom->dwc3->dev);
-	of_platform_depopulate(dev);
+	if (np) {
+		of_platform_depopulate(&pdev->dev);
+	} else {
+		device_remove_software_node(&qcom->dwc3->dev);
+		platform_device_del(qcom->dwc3);
+	}
+	platform_device_put(qcom->dwc3);
+
+	if (qcom->urs_usb)
+		dwc3_qcom_destroy_urs_usb_platdev(qcom->urs_usb);
 
 	for (i = qcom->num_clocks - 1; i >= 0; i--) {
 		clk_disable_unprepare(qcom->clks[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-st.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-st.c
@@ -219,10 +219,8 @@
 	dwc3_data->regmap = regmap;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "syscfg-reg");
-	if (!res) {
-		ret = -ENXIO;
-		goto undo_platform_dev_alloc;
-	}
+	if (!res)
+		return -ENXIO;
 
 	dwc3_data->syscfg_reg_off = res->start;
 
@@ -233,8 +231,7 @@
 		devm_reset_control_get_exclusive(dev, "powerdown");
 	if (IS_ERR(dwc3_data->rstc_pwrdn)) {
 		dev_err(&pdev->dev, "could not get power controller\n");
-		ret = PTR_ERR(dwc3_data->rstc_pwrdn);
-		goto undo_platform_dev_alloc;
+		return PTR_ERR(dwc3_data->rstc_pwrdn);
 	}
 
 	/* Manage PowerDown */
@@ -269,7 +266,7 @@
 	if (!child_pdev) {
 		dev_err(dev, "failed to find dwc3 core device\n");
 		ret = -ENODEV;
-		goto err_node_put;
+		goto depopulate;
 	}
 
 	dwc3_data->dr_mode = usb_get_dr_mode(&child_pdev->dev);
@@ -285,6 +282,7 @@
 	ret = st_dwc3_drd_init(dwc3_data);
 	if (ret) {
 		dev_err(dev, "drd initialisation failed\n");
+		of_platform_depopulate(dev);
 		goto undo_softreset;
 	}
 
@@ -294,14 +292,14 @@
 	platform_set_drvdata(pdev, dwc3_data);
 	return 0;
 
+depopulate:
+	of_platform_depopulate(dev);
 err_node_put:
 	of_node_put(child);
 undo_softreset:
 	reset_control_assert(dwc3_data->rstc_rst);
 undo_powerdown:
 	reset_control_assert(dwc3_data->rstc_pwrdn);
-undo_platform_dev_alloc:
-	platform_device_put(pdev);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/dwc3-xilinx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/dwc3-xilinx.c
@@ -13,16 +13,23 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
+#include <linux/of_gpio.h>
 #include <linux/of_platform.h>
 #include <linux/pm_runtime.h>
 #include <linux/reset.h>
 #include <linux/of_address.h>
 #include <linux/delay.h>
 #include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/of.h>
 #include <linux/io.h>
 
 #include <linux/phy/phy.h>
 
+#include "core.h"
+
 /* USB phy reset mask register */
 #define XLNX_USB_PHY_RST_EN			0x001C
 #define XLNX_PHY_RST_MASK			0x1
@@ -31,6 +38,25 @@
 #define XLNX_USB_TRAFFIC_ROUTE_CONFIG		0x005C
 #define XLNX_USB_TRAFFIC_ROUTE_FPD		0x1
 
+#define XLNX_USB_CUR_PWR_STATE			0x0000
+#define XLNX_CUR_PWR_STATE_D0			0x00
+#define XLNX_CUR_PWR_STATE_D3			0x0F
+#define XLNX_CUR_PWR_STATE_BITMASK		0x0F
+
+#define XLNX_USB_PME_ENABLE			0x0034
+#define XLNX_PME_ENABLE_SIG_GEN			0x01
+
+#define XLNX_USB_REQ_PWR_STATE			0x003c
+#define XLNX_REQ_PWR_STATE_D0			0x00
+#define XLNX_REQ_PWR_STATE_D3			0x03
+
+/* Number of retries for USB operations */
+#define DWC3_PWR_STATE_RETRIES			1000
+#define DWC3_PWR_TIMEOUT			100
+
+/* Versal USB Node ID */
+#define VERSAL_USB_NODE_ID			0x18224018
+
 /* Versal USB Reset ID */
 #define VERSAL_USB_RESET_ID			0xC104036
 
@@ -40,14 +66,270 @@
 #define XLNX_USB_FPD_POWER_PRSNT		0x80
 #define FPD_POWER_PRSNT_OPTION			BIT(0)
 
+enum dwc3_xlnx_core_state {
+	UNKNOWN_STATE = 0,
+	D0_STATE,
+	D3_STATE
+};
+
 struct dwc3_xlnx {
 	int				num_clocks;
 	struct clk_bulk_data		*clks;
 	struct device			*dev;
 	void __iomem			*regs;
 	int				(*pltfm_init)(struct dwc3_xlnx *data);
+	struct phy			*usb3_phy;
+	struct regulator		*dwc3_pmu;
+	struct regulator_dev		*dwc3_xlnx_reg_rdev;
+	enum dwc3_xlnx_core_state	pmu_state;
+	bool				wakeup_capable;
+	struct reset_control		*crst;
+	bool				enable_d3_suspend;
+	enum usb_dr_mode		dr_mode;
+	struct regulator_desc		dwc3_xlnx_reg_desc;
+};
+
+static const char *const usb_dr_modes[] = {
+	[USB_DR_MODE_UNKNOWN]		= "",
+	[USB_DR_MODE_HOST]		= "host",
+	[USB_DR_MODE_PERIPHERAL]	= "peripheral",
+	[USB_DR_MODE_OTG]		= "otg",
+};
+
+static enum usb_dr_mode usb_get_dr_mode_from_string(const char *str)
+{
+	int ret;
+
+	ret = match_string(usb_dr_modes, ARRAY_SIZE(usb_dr_modes), str);
+	return (ret < 0) ? USB_DR_MODE_UNKNOWN : ret;
+}
+
+#ifdef CONFIG_PM
+static struct regulator_init_data dwc3_xlnx_reg_initdata = {
+	.constraints = {
+		.always_on = 0,
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
 };
 
+static int dwc3_zynqmp_power_req(struct device *dev, bool on)
+{
+	u32 reg, retries;
+	void __iomem *reg_base;
+	struct dwc3_xlnx *priv_data;
+	int ret;
+
+	priv_data = dev_get_drvdata(dev);
+	reg_base = priv_data->regs;
+
+	/* Check if entering into D3 state is allowed during suspend */
+	if (!priv_data->enable_d3_suspend)
+		return 0;
+
+	if (on) {
+		dev_dbg(priv_data->dev,
+			"trying to set power state to D0....\n");
+
+		if (priv_data->pmu_state == D0_STATE)
+			return 0;
+
+		/* Release USB core reset , which was assert during D3 entry */
+		ret = reset_control_deassert(priv_data->crst);
+		if (ret < 0) {
+			dev_err(dev, "Failed to release core reset\n");
+			return ret;
+		}
+
+		/* change power state to D0 */
+		writel(XLNX_REQ_PWR_STATE_D0,
+		       reg_base + XLNX_USB_REQ_PWR_STATE);
+
+		/* wait till current state is changed to D0 */
+		retries = DWC3_PWR_STATE_RETRIES;
+		do {
+			reg = readl(reg_base + XLNX_USB_CUR_PWR_STATE);
+			if ((reg & XLNX_CUR_PWR_STATE_BITMASK) ==
+			     XLNX_CUR_PWR_STATE_D0)
+				break;
+
+			udelay(DWC3_PWR_TIMEOUT);
+		} while (--retries);
+
+		if (!retries) {
+			dev_err(priv_data->dev,
+				"Failed to set power state to D0\n");
+			return -EIO;
+		}
+
+		priv_data->pmu_state = D0_STATE;
+		/* disable D3 entry */
+		priv_data->enable_d3_suspend = false;
+	} else {
+		dev_dbg(priv_data->dev, "Trying to set power state to D3...\n");
+
+		if (priv_data->pmu_state == D3_STATE)
+			return 0;
+
+		/* enable PME to wakeup from hibernation */
+		writel(XLNX_PME_ENABLE_SIG_GEN, reg_base + XLNX_USB_PME_ENABLE);
+
+		/* change power state to D3 */
+		writel(XLNX_REQ_PWR_STATE_D3,
+		       reg_base + XLNX_USB_REQ_PWR_STATE);
+
+		/* wait till current state is changed to D3 */
+		retries = DWC3_PWR_STATE_RETRIES;
+		do {
+			reg = readl(reg_base + XLNX_USB_CUR_PWR_STATE);
+			if ((reg & XLNX_CUR_PWR_STATE_BITMASK) ==
+					XLNX_CUR_PWR_STATE_D3)
+				break;
+
+			udelay(DWC3_PWR_TIMEOUT);
+		} while (--retries);
+
+		if (!retries) {
+			dev_err(priv_data->dev,
+				"Failed to set power state to D3\n");
+			return -EIO;
+		}
+
+		/* Assert USB core reset after entering D3 state */
+		ret = reset_control_assert(priv_data->crst);
+		if (ret < 0) {
+			dev_err(dev, "Failed to assert core reset\n");
+			return ret;
+		}
+
+		priv_data->pmu_state = D3_STATE;
+	}
+
+	return 0;
+}
+
+static int dwc3_versal_power_req(struct device *dev, bool on)
+{
+	int ret;
+	struct dwc3_xlnx *priv_data;
+
+	priv_data = dev_get_drvdata(dev);
+
+	if (on) {
+		dev_dbg(dev, "%s:Trying to set power state to D0....\n",
+			 __func__);
+
+		if (priv_data->pmu_state == D0_STATE)
+			return 0;
+
+		ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
+					     PM_RESET_ACTION_RELEASE);
+		if (ret < 0)
+			dev_err(priv_data->dev, "failed to De-assert Reset\n");
+
+		ret = zynqmp_pm_usb_set_state(VERSAL_USB_NODE_ID,
+					      XLNX_REQ_PWR_STATE_D0,
+					      DWC3_PWR_STATE_RETRIES *
+					      DWC3_PWR_TIMEOUT);
+		if (ret < 0)
+			dev_err(priv_data->dev, "failed to enter D0 state\n");
+
+		priv_data->pmu_state = D0_STATE;
+	} else {
+		dev_dbg(dev, "%s:Trying to set power state to D3...\n",
+			__func__);
+
+		if (priv_data->pmu_state == D3_STATE)
+			return 0;
+
+		ret = zynqmp_pm_usb_set_state(VERSAL_USB_NODE_ID,
+					      XLNX_REQ_PWR_STATE_D3,
+					      DWC3_PWR_STATE_RETRIES *
+					      DWC3_PWR_TIMEOUT);
+		if (ret < 0)
+			dev_err(priv_data->dev, "failed to enter D3 state\n");
+
+		ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
+					     PM_RESET_ACTION_ASSERT);
+		if (ret < 0)
+			dev_err(priv_data->dev, "failed to assert Reset\n");
+
+		priv_data->pmu_state = D3_STATE;
+	}
+
+	return ret;
+}
+
+static int dwc3_set_usb_core_power(struct device *dev, bool on)
+{
+	int ret;
+	struct device_node *node = dev->of_node;
+
+	if (of_device_is_compatible(node, "xlnx,zynqmp-dwc3"))
+		/* Set D3/D0 state for ZynqMP */
+		ret = dwc3_zynqmp_power_req(dev, on);
+	else if (of_device_is_compatible(node, "xlnx,versal-dwc3"))
+		/* Set D3/D0 state for Versal */
+		ret = dwc3_versal_power_req(dev, on);
+	else
+		/* This is only for Xilinx devices */
+		return 0;
+
+	return ret;
+}
+
+static int dwc3_xlnx_reg_enable(struct regulator_dev *rdev)
+{
+	return dwc3_set_usb_core_power(rdev->dev.parent, true);
+}
+
+static int dwc3_xlnx_reg_disable(struct regulator_dev *rdev)
+{
+	return dwc3_set_usb_core_power(rdev->dev.parent, false);
+}
+
+static int dwc3_xlnx_reg_is_enabled(struct regulator_dev *rdev)
+{
+	struct dwc3_xlnx	*priv_data = dev_get_drvdata(rdev->dev.parent);
+
+	return !!(priv_data->pmu_state == D0_STATE);
+}
+
+static struct regulator_ops dwc3_xlnx_reg_ops = {
+	.enable			= dwc3_xlnx_reg_enable,
+	.disable		= dwc3_xlnx_reg_disable,
+	.is_enabled		= dwc3_xlnx_reg_is_enabled,
+};
+
+static int dwc3_xlnx_register_regulator(struct device *dev,
+					struct dwc3_xlnx *priv_data)
+{
+	struct regulator_config config = { };
+	int ret = 0;
+
+	config.dev = dev;
+	config.driver_data = (void *)priv_data;
+	config.init_data = &dwc3_xlnx_reg_initdata;
+
+	priv_data->dwc3_xlnx_reg_desc.name = dev->of_node->full_name;
+	priv_data->dwc3_xlnx_reg_desc.id = -1;
+	priv_data->dwc3_xlnx_reg_desc.type = REGULATOR_VOLTAGE;
+	priv_data->dwc3_xlnx_reg_desc.owner = THIS_MODULE;
+	priv_data->dwc3_xlnx_reg_desc.ops = &dwc3_xlnx_reg_ops;
+
+	/* Register the dwc3 PMU regulator */
+	priv_data->dwc3_xlnx_reg_rdev =
+		devm_regulator_register(dev, &priv_data->dwc3_xlnx_reg_desc,
+					&config);
+
+	if (IS_ERR(priv_data->dwc3_xlnx_reg_rdev)) {
+		ret = PTR_ERR(priv_data->dwc3_xlnx_reg_rdev);
+		pr_err("Failed to register regulator: %d\n", ret);
+	}
+
+	return ret;
+}
+#endif
+
 static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool mask)
 {
 	u32 reg;
@@ -98,17 +380,9 @@
 {
 	struct device		*dev = priv_data->dev;
 	struct reset_control	*crst, *hibrst, *apbrst;
-	struct phy		*usb3_phy;
 	int			ret;
 	u32			reg;
-
-	usb3_phy = devm_phy_get(dev, "usb3-phy");
-	if (PTR_ERR(usb3_phy) == -EPROBE_DEFER) {
-		ret = -EPROBE_DEFER;
-		goto err;
-	} else if (IS_ERR(usb3_phy)) {
-		usb3_phy = NULL;
-	}
+	struct gpio_desc	*reset_gpio = NULL;
 
 	crst = devm_reset_control_get_exclusive(dev, "usb_crst");
 	if (IS_ERR(crst)) {
@@ -117,6 +391,7 @@
 			      "failed to get core reset signal\n");
 		goto err;
 	}
+	priv_data->crst = crst;
 
 	hibrst = devm_reset_control_get_exclusive(dev, "usb_hibrst");
 	if (IS_ERR(hibrst)) {
@@ -134,6 +409,25 @@
 		goto err;
 	}
 
+	priv_data->usb3_phy = devm_phy_optional_get(dev, "usb3-phy");
+	if (IS_ERR(priv_data->usb3_phy)) {
+		ret = PTR_ERR(priv_data->usb3_phy);
+		dev_err_probe(dev, ret,
+			      "failed to get USB3 PHY\n");
+		goto err;
+	}
+
+	/*
+	 * When no USB3 PHY 'usb3-phy' property is specified in the
+	 * device-tree, then zynqmp board work as a USB2.0 mode only.
+	 * USB2.0 mode only design is non-SerDes based, so we are
+	 * skipping phy initialization.
+	 */
+	if (!priv_data->usb3_phy) {
+		ret = 0;
+		goto skip_usb3_phy;
+	}
+
 	ret = reset_control_assert(crst);
 	if (ret < 0) {
 		dev_err(dev, "Failed to assert core reset\n");
@@ -152,9 +446,9 @@
 		goto err;
 	}
 
-	ret = phy_init(usb3_phy);
+	ret = phy_init(priv_data->usb3_phy);
 	if (ret < 0) {
-		phy_exit(usb3_phy);
+		phy_exit(priv_data->usb3_phy);
 		goto err;
 	}
 
@@ -182,12 +476,30 @@
 		goto err;
 	}
 
-	ret = phy_power_on(usb3_phy);
+	ret = phy_power_on(priv_data->usb3_phy);
 	if (ret < 0) {
-		phy_exit(usb3_phy);
+		phy_exit(priv_data->usb3_phy);
+		goto err;
+	}
+
+skip_usb3_phy:
+	/* ulpi reset via gpio-modepin or gpio-framework driver */
+	reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(reset_gpio)) {
+		ret = PTR_ERR(reset_gpio);
+		dev_err_probe(dev, ret,
+			      "Failed to bind reset gpio %d,errcode\n", ret);
 		goto err;
 	}
 
+	if (reset_gpio) {
+		/* Toggle ulpi to reset the phy. */
+		gpiod_set_value_cansleep(reset_gpio, 1);
+		usleep_range(5000, 10000); /* delay */
+		gpiod_set_value_cansleep(reset_gpio, 0);
+		usleep_range(5000, 10000); /* delay */
+	}
+
 	/*
 	 * This routes the USB DMA traffic to go through FPD path instead
 	 * of reaching DDR directly. This traffic routing is needed to
@@ -203,6 +515,36 @@
 	return ret;
 }
 
+/* xilinx feature support functions */
+void dwc3_xilinx_wakeup_capable(struct device *dev, bool wakeup)
+{
+	struct device_node *node = of_node_get(dev->parent->of_node);
+
+	/* check for valid parent node */
+	while (node) {
+		if (of_device_is_compatible(node, "xlnx,zynqmp-dwc3") ||
+		    of_device_is_compatible(node, "xlnx,versal-dwc3"))
+			break;
+
+		/* get the next parent node */
+		node = of_get_next_parent(node);
+	}
+
+	if (node) {
+		struct platform_device *pdev_parent;
+		struct dwc3_xlnx *priv_data;
+
+		pdev_parent = of_find_device_by_node(node);
+		priv_data = platform_get_drvdata(pdev_parent);
+
+		/* Set wakeup capable as true or false */
+		priv_data->wakeup_capable = wakeup;
+
+		/* Allow D3 state if wakeup capable only */
+		priv_data->enable_d3_suspend = wakeup;
+	}
+}
+
 static const struct of_device_id dwc3_xlnx_of_match[] = {
 	{
 		.compatible = "xlnx,zynqmp-dwc3",
@@ -221,9 +563,11 @@
 	struct dwc3_xlnx		*priv_data;
 	struct device			*dev = &pdev->dev;
 	struct device_node		*np = dev->of_node;
+	struct device_node		*dwc3_child_node = NULL;
 	const struct of_device_id	*match;
 	void __iomem			*regs;
 	int				ret;
+	const char                      *dr_modes;
 
 	priv_data = devm_kzalloc(dev, sizeof(*priv_data), GFP_KERNEL);
 	if (!priv_data)
@@ -238,12 +582,39 @@
 
 	match = of_match_node(dwc3_xlnx_of_match, pdev->dev.of_node);
 
+	dwc3_child_node = of_get_next_child(pdev->dev.of_node, dwc3_child_node);
+	if (!dwc3_child_node)
+		return -ENODEV;
+
 	priv_data->pltfm_init = match->data;
 	priv_data->regs = regs;
 	priv_data->dev = dev;
 
+	/* get the dr_mode from child node */
+	ret = of_property_read_string(dwc3_child_node, "dr_mode", &dr_modes);
+	if (ret < 0)
+		priv_data->dr_mode = USB_DR_MODE_UNKNOWN;
+	else
+		priv_data->dr_mode = usb_get_dr_mode_from_string(dr_modes);
+
+	of_node_put(dwc3_child_node);
+
+	/*
+	 * TODO: This flag needs to be handled while implementing
+	 *	the remote wake-up feature.
+	 */
+	priv_data->enable_d3_suspend = false;
+
 	platform_set_drvdata(pdev, priv_data);
 
+#ifdef CONFIG_PM
+	ret = dwc3_xlnx_register_regulator(dev, priv_data);
+	if (ret)
+		return ret;
+#endif
+	/* Register the dwc3-xilinx wakeup function to dwc3 host */
+	dwc3_host_wakeup_register(dwc3_xilinx_wakeup_capable);
+
 	ret = devm_clk_bulk_get_all(priv_data->dev, &priv_data->clks);
 	if (ret < 0)
 		return ret;
@@ -282,6 +653,8 @@
 
 	of_platform_depopulate(dev);
 
+	/* Unregister the dwc3-xilinx wakeup function from dwc3 host */
+	dwc3_host_wakeup_register(NULL);
 	clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data->clks);
 	priv_data->num_clocks = 0;
 
@@ -292,7 +665,7 @@
 	return 0;
 }
 
-static int __maybe_unused dwc3_xlnx_suspend_common(struct device *dev)
+static int __maybe_unused dwc3_xlnx_runtime_suspend(struct device *dev)
 {
 	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
 
@@ -301,7 +674,7 @@
 	return 0;
 }
 
-static int __maybe_unused dwc3_xlnx_resume_common(struct device *dev)
+static int __maybe_unused dwc3_xlnx_runtime_resume(struct device *dev)
 {
 	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
 
@@ -316,8 +689,61 @@
 	return 0;
 }
 
-static UNIVERSAL_DEV_PM_OPS(dwc3_xlnx_dev_pm_ops, dwc3_xlnx_suspend_common,
-			    dwc3_xlnx_resume_common, dwc3_xlnx_runtime_idle);
+static int __maybe_unused dwc3_xlnx_suspend(struct device *dev)
+{
+	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
+
+	if (!priv_data->wakeup_capable) {
+#ifdef CONFIG_PM
+		if (priv_data->dr_mode == USB_DR_MODE_PERIPHERAL)
+			/* Put the core into D3 */
+			dwc3_set_usb_core_power(dev, false);
+#endif
+		phy_exit(priv_data->usb3_phy);
+
+		/* Disable the clocks */
+		clk_bulk_disable(priv_data->num_clocks, priv_data->clks);
+	}
+	return 0;
+}
+
+static int __maybe_unused dwc3_xlnx_resume(struct device *dev)
+{
+	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
+	int ret;
+
+	if (priv_data->wakeup_capable)
+		return 0;
+
+#ifdef CONFIG_PM
+	if (priv_data->dr_mode == USB_DR_MODE_PERIPHERAL)
+		/* Put the core into D0 */
+		dwc3_set_usb_core_power(dev, true);
+#endif
+
+	/* Enabled the clocks */
+	ret = clk_bulk_enable(priv_data->num_clocks, priv_data->clks);
+	if (ret)
+		return ret;
+
+	ret = phy_init(priv_data->usb3_phy);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_power_on(priv_data->usb3_phy);
+	if (ret < 0) {
+		phy_exit(priv_data->usb3_phy);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct dev_pm_ops dwc3_xlnx_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(dwc3_xlnx_suspend, dwc3_xlnx_resume)
+	SET_RUNTIME_PM_OPS(dwc3_xlnx_runtime_suspend,
+			dwc3_xlnx_runtime_resume, dwc3_xlnx_runtime_idle)
+};
 
 static struct platform_driver dwc3_xlnx_driver = {
 	.probe		= dwc3_xlnx_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/ep0.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/ep0.c
@@ -218,7 +218,7 @@
 	return ret;
 }
 
-static void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
+void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
 {
 	struct dwc3_ep		*dep;
 
@@ -236,7 +236,10 @@
 		struct dwc3_request	*req;
 
 		req = next_request(&dep->pending_list);
-		dwc3_gadget_giveback(dep, req, -ECONNRESET);
+		if (!dwc->connected)
+			dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
+		else
+			dwc3_gadget_giveback(dep, req, -ECONNRESET);
 	}
 
 	dwc->ep0state = EP0_SETUP_PHASE;
@@ -271,6 +274,7 @@
 {
 	struct dwc3_ep			*dep;
 	int				ret;
+	int                             i;
 
 	complete(&dwc->ep0_in_setup);
 
@@ -279,6 +283,19 @@
 			DWC3_TRBCTL_CONTROL_SETUP, false);
 	ret = dwc3_ep0_start_trans(dep);
 	WARN_ON(ret < 0);
+	for (i = 2; i < DWC3_ENDPOINTS_NUM; i++) {
+		struct dwc3_ep *dwc3_ep;
+
+		dwc3_ep = dwc->eps[i];
+		if (!dwc3_ep)
+			continue;
+
+		if (!(dwc3_ep->flags & DWC3_EP_DELAY_STOP))
+			continue;
+
+		dwc3_ep->flags &= ~DWC3_EP_DELAY_STOP;
+		dwc3_stop_active_transfer(dwc3_ep, true, true);
+	}
 }
 
 static struct dwc3_ep *dwc3_wIndex_to_dep(struct dwc3 *dwc, __le16 wIndex_le)
@@ -339,6 +356,11 @@
 				usb_status |= 1 << USB_DEV_STAT_U2_ENABLED;
 		}
 
+		/* Sends the status indicating if the remote wakeup is
+		 * supported by device.
+		 */
+		usb_status |= dwc->remote_wakeup << USB_DEVICE_REMOTE_WAKEUP;
+
 		break;
 
 	case USB_RECIP_INTERFACE:
@@ -457,6 +479,11 @@
 
 	switch (wValue) {
 	case USB_DEVICE_REMOTE_WAKEUP:
+		if (set)
+			dwc->remote_wakeup = 1;
+		else
+			dwc->remote_wakeup = 0;
+
 		break;
 	/*
 	 * 9.4.1 says only only for SS, in AddressState only for
@@ -474,6 +501,34 @@
 	case USB_DEVICE_TEST_MODE:
 		ret = dwc3_ep0_handle_test(dwc, state, wIndex, set);
 		break;
+	case USB_DEVICE_B_HNP_ENABLE:
+		if (set) {
+			if (dwc->gadget->host_request_flag) {
+				struct usb_phy *phy =
+					usb_get_phy(USB_PHY_TYPE_USB3);
+
+				dwc->gadget->b_hnp_enable = 0;
+				dwc->gadget->host_request_flag = 0;
+				otg_start_hnp(phy->otg);
+				usb_put_phy(phy);
+			} else {
+				dwc->gadget->b_hnp_enable = 1;
+			}
+		} else
+			return -EINVAL;
+		break;
+
+	case USB_DEVICE_A_HNP_SUPPORT:
+		/* RH port supports HNP */
+		dev_dbg(dwc->dev,
+			    "SET_FEATURE: USB_DEVICE_A_HNP_SUPPORT\n");
+		break;
+
+	case USB_DEVICE_A_ALT_HNP_SUPPORT:
+		/* other RH port does */
+		dev_dbg(dwc->dev,
+			    "SET_FEATURE: USB_DEVICE_A_ALT_HNP_SUPPORT\n");
+		break;
 	default:
 		ret = -EINVAL;
 	}
@@ -764,7 +819,10 @@
 
 	switch (ctrl->bRequest) {
 	case USB_REQ_GET_STATUS:
-		ret = dwc3_ep0_handle_status(dwc, ctrl);
+		if (le16_to_cpu(ctrl->wIndex) == OTG_STS_SELECTOR)
+			ret = dwc3_ep0_delegate_req(dwc, ctrl);
+		else
+			ret = dwc3_ep0_handle_status(dwc, ctrl);
 		break;
 	case USB_REQ_CLEAR_FEATURE:
 		ret = dwc3_ep0_handle_feature(dwc, ctrl, 0);
@@ -799,7 +857,7 @@
 	int ret = -EINVAL;
 	u32 len;
 
-	if (!dwc->gadget_driver)
+	if (!dwc->gadget_driver || !dwc->connected)
 		goto out;
 
 	trace_dwc3_ctrl_req(ctrl);
@@ -1073,13 +1131,18 @@
 	__dwc3_ep0_do_control_status(dwc, dwc->eps[direction]);
 }
 
-static void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
+void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
 {
 	struct dwc3_gadget_ep_cmd_params params;
 	u32			cmd;
 	int			ret;
 
-	if (!dep->resource_index)
+	/*
+	 * For status/DATA OUT stage, TRB will be queued on ep0 out
+	 * endpoint for which resource index is zero. Hence allow
+	 * queuing ENDXFER command for ep0 out endpoint.
+	 */
+	if (!dep->resource_index && dep->number)
 		return;
 
 	cmd = DWC3_DEPCMD_ENDTRANSFER;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/gadget.c
@@ -139,6 +139,24 @@
 	return -ETIMEDOUT;
 }
 
+static void dwc3_ep0_reset_state(struct dwc3 *dwc)
+{
+	unsigned int	dir;
+
+	if (dwc->ep0state != EP0_SETUP_PHASE) {
+		dir = !!dwc->ep0_expect_in;
+		if (dwc->ep0state == EP0_DATA_PHASE)
+			dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
+		else
+			dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
+
+		dwc->eps[0]->trb_enqueue = 0;
+		dwc->eps[1]->trb_enqueue = 0;
+
+		dwc3_ep0_stall_and_restart(dwc);
+	}
+}
+
 /**
  * dwc3_ep_inc_trb - increment a trb index.
  * @index: Pointer to the TRB index to increment.
@@ -180,6 +198,7 @@
 	list_del(&req->list);
 	req->remaining = 0;
 	req->needs_extra_trb = false;
+	req->num_trbs = 0;
 
 	if (req->request.status == -EINPROGRESS)
 		req->request.status = status;
@@ -210,6 +229,9 @@
 {
 	struct dwc3			*dwc = dep->dwc;
 
+	if (dep->stream_capable && timer_pending(&req->stream_timeout_timer))
+		del_timer(&req->stream_timeout_timer);
+
 	dwc3_gadget_del_and_unmap_request(dep, req, status);
 	req->status = DWC3_REQUEST_STATUS_COMPLETED;
 
@@ -274,7 +296,7 @@
 {
 	const struct usb_endpoint_descriptor *desc = dep->endpoint.desc;
 	struct dwc3		*dwc = dep->dwc;
-	u32			timeout = 5000;
+	u32			timeout = 10000;
 	u32			saved_config = 0;
 	u32			reg;
 
@@ -291,7 +313,8 @@
 	 *
 	 * DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
 	 */
-	if (dwc->gadget->speed <= USB_SPEED_HIGH) {
+	if (dwc->gadget->speed <= USB_SPEED_HIGH ||
+	    DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_ENDTRANSFER) {
 		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
 		if (unlikely(reg & DWC3_GUSB2PHYCFG_SUSPHY)) {
 			saved_config |= DWC3_GUSB2PHYCFG_SUSPHY;
@@ -310,19 +333,38 @@
 	if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
 		int link_state;
 
+		/*
+		 * Initiate remote wakeup if the link state is in U3 when
+		 * operating in SS/SSP or L1/L2 when operating in HS/FS. If the
+		 * link state is in U1/U2, no remote wakeup is needed. The Start
+		 * Transfer command will initiate the link recovery.
+		 */
 		link_state = dwc3_gadget_get_link_state(dwc);
-		if (link_state == DWC3_LINK_STATE_U1 ||
-		    link_state == DWC3_LINK_STATE_U2 ||
-		    link_state == DWC3_LINK_STATE_U3) {
+		switch (link_state) {
+		case DWC3_LINK_STATE_U2:
+			if (dwc->gadget->speed >= USB_SPEED_SUPER)
+				break;
+
+			fallthrough;
+		case DWC3_LINK_STATE_U3:
 			ret = __dwc3_gadget_wakeup(dwc);
 			dev_WARN_ONCE(dwc->dev, ret, "wakeup failed --> %d\n",
 					ret);
+			break;
 		}
 	}
 
-	dwc3_writel(dep->regs, DWC3_DEPCMDPAR0, params->param0);
-	dwc3_writel(dep->regs, DWC3_DEPCMDPAR1, params->param1);
-	dwc3_writel(dep->regs, DWC3_DEPCMDPAR2, params->param2);
+	/*
+	 * For some commands such as Update Transfer command, DEPCMDPARn
+	 * registers are reserved. Since the driver often sends Update Transfer
+	 * command, don't write to DEPCMDPARn to avoid register write delays and
+	 * improve performance.
+	 */
+	if (DWC3_DEPCMD_CMD(cmd) != DWC3_DEPCMD_UPDATETRANSFER) {
+		dwc3_writel(dep->regs, DWC3_DEPCMDPAR0, params->param0);
+		dwc3_writel(dep->regs, DWC3_DEPCMDPAR1, params->param1);
+		dwc3_writel(dep->regs, DWC3_DEPCMDPAR2, params->param2);
+	}
 
 	/*
 	 * Synopsys Databook 2.60a states in section 6.3.2.5.6 of that if we're
@@ -346,6 +388,12 @@
 		cmd |= DWC3_DEPCMD_CMDACT;
 
 	dwc3_writel(dep->regs, DWC3_DEPCMD, cmd);
+
+	if (!(cmd & DWC3_DEPCMD_CMDACT)) {
+		ret = 0;
+		goto skip_status;
+	}
+
 	do {
 		reg = dwc3_readl(dep->regs, DWC3_DEPCMD);
 		if (!(reg & DWC3_DEPCMD_CMDACT)) {
@@ -387,6 +435,7 @@
 		cmd_status = -ETIMEDOUT;
 	}
 
+skip_status:
 	trace_dwc3_gadget_ep_cmd(dep, cmd, params, cmd_status);
 
 	if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
@@ -430,7 +479,7 @@
 	return dwc3_send_gadget_ep_cmd(dep, cmd, &params);
 }
 
-static dma_addr_t dwc3_trb_dma_offset(struct dwc3_ep *dep,
+dma_addr_t dwc3_trb_dma_offset(struct dwc3_ep *dep,
 		struct dwc3_trb *trb)
 {
 	u32		offset = (char *) trb - (char *) dep->trb_pool;
@@ -533,7 +582,7 @@
 		return ret;
 
 	for (i = 0; i < DWC3_ENDPOINTS_NUM; i++) {
-		struct dwc3_ep *dep = dwc->eps[i];
+		dep = dwc->eps[i];
 
 		if (!dep)
 			continue;
@@ -546,6 +595,20 @@
 	return 0;
 }
 
+static void stream_timeout_function(struct timer_list *arg)
+{
+	struct dwc3_request	*req = from_timer(req, arg,
+						stream_timeout_timer);
+	struct dwc3_ep		*dep = req->dep;
+	struct dwc3		*dwc = dep->dwc;
+	unsigned long		flags;
+
+	spin_lock_irqsave(&dwc->lock, flags);
+	dwc3_stop_active_transfer(dep, true, true);
+	__dwc3_gadget_kick_transfer(dep);
+	spin_unlock_irqrestore(&dwc->lock, flags);
+}
+
 static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)
 {
 	const struct usb_ss_ep_comp_descriptor *comp_desc;
@@ -628,9 +691,6 @@
 	return dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_SETEPCONFIG, &params);
 }
 
-static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
-		bool interrupt);
-
 /**
  * dwc3_gadget_calc_tx_fifo_size - calculates the txfifo size value
  * @dwc: pointer to the DWC3 context
@@ -702,6 +762,7 @@
 				   DWC31_GTXFIFOSIZ_TXFRAMNUM;
 
 		dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
+		dep->flags &= ~DWC3_EP_TXFIFO_RESIZED;
 	}
 	dwc->num_ep_resized = 0;
 }
@@ -747,6 +808,10 @@
 	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
 		return 0;
 
+	/* bail if already resized */
+	if (dep->flags & DWC3_EP_TXFIFO_RESIZED)
+		return 0;
+
 	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
 
 	if ((dep->endpoint.maxburst > 1 &&
@@ -807,6 +872,7 @@
 	}
 
 	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);
+	dep->flags |= DWC3_EP_TXFIFO_RESIZED;
 	dwc->num_ep_resized++;
 
 	return 0;
@@ -820,7 +886,7 @@
  * Caller should take care of locking. Execute all necessary commands to
  * initialize a HW endpoint so it can be used by a gadget driver.
  */
-static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
+int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
 {
 	const struct usb_endpoint_descriptor *desc = dep->endpoint.desc;
 	struct dwc3		*dwc = dep->dwc;
@@ -828,7 +894,7 @@
 	u32			reg;
 	int			ret;
 
-	if (!(dep->flags & DWC3_EP_ENABLED)) {
+	if (!(dep->flags & DWC3_EP_ENABLED) || dwc->is_hibernated) {
 		ret = dwc3_gadget_resize_tx_fifos(dep);
 		if (ret)
 			return ret;
@@ -842,7 +908,7 @@
 	if (ret)
 		return ret;
 
-	if (!(dep->flags & DWC3_EP_ENABLED)) {
+	if (!(dep->flags & DWC3_EP_ENABLED) || dwc->is_hibernated) {
 		struct dwc3_trb	*trb_st_hw;
 		struct dwc3_trb	*trb_link;
 
@@ -853,14 +919,17 @@
 		reg |= DWC3_DALEPENA_EP(dep->number);
 		dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);
 
+		dep->trb_dequeue = 0;
+		dep->trb_enqueue = 0;
+
 		if (usb_endpoint_xfer_control(desc))
 			goto out;
 
-		/* Initialize the TRB ring */
-		dep->trb_dequeue = 0;
-		dep->trb_enqueue = 0;
-		memset(dep->trb_pool, 0,
-		       sizeof(struct dwc3_trb) * DWC3_TRB_NUM);
+		if (!dwc->is_hibernated) {
+			/* Initialize the TRB ring */
+			memset(dep->trb_pool, 0,
+			       sizeof(struct dwc3_trb) * DWC3_TRB_NUM);
+		}
 
 		/* Link TRB. The HWO bit is never reset */
 		trb_st_hw = &dep->trb_pool[0];
@@ -876,8 +945,8 @@
 	 * Issue StartTransfer here with no-op TRB so we can always rely on No
 	 * Response Update Transfer command.
 	 */
-	if (usb_endpoint_xfer_bulk(desc) ||
-			usb_endpoint_xfer_int(desc)) {
+	if ((usb_endpoint_xfer_bulk(desc) || usb_endpoint_xfer_int(desc)) &&
+	     !dwc->is_hibernated) {
 		struct dwc3_gadget_ep_cmd_params params;
 		struct dwc3_trb	*trb;
 		dma_addr_t trb_dma;
@@ -934,7 +1003,7 @@
 	return 0;
 }
 
-static void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep)
+static void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep, int status)
 {
 	struct dwc3_request		*req;
 
@@ -944,19 +1013,19 @@
 	while (!list_empty(&dep->started_list)) {
 		req = next_request(&dep->started_list);
 
-		dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
+		dwc3_gadget_giveback(dep, req, status);
 	}
 
 	while (!list_empty(&dep->pending_list)) {
 		req = next_request(&dep->pending_list);
 
-		dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
+		dwc3_gadget_giveback(dep, req, status);
 	}
 
 	while (!list_empty(&dep->cancelled_list)) {
 		req = next_request(&dep->cancelled_list);
 
-		dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
+		dwc3_gadget_giveback(dep, req, status);
 	}
 }
 
@@ -970,7 +1039,7 @@
  *
  * Caller should take care of locking.
  */
-static int __dwc3_gadget_ep_disable(struct dwc3_ep *dep)
+int __dwc3_gadget_ep_disable(struct dwc3_ep *dep)
 {
 	struct dwc3		*dwc = dep->dwc;
 	u32			reg;
@@ -985,18 +1054,18 @@
 	reg &= ~DWC3_DALEPENA_EP(dep->number);
 	dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);
 
+	dwc3_remove_requests(dwc, dep, -ESHUTDOWN);
+
+	dep->stream_capable = false;
+	dep->type = 0;
+	dep->flags &= DWC3_EP_TXFIFO_RESIZED;
+
 	/* Clear out the ep descriptors for non-ep0 */
 	if (dep->number > 1) {
 		dep->endpoint.comp_desc = NULL;
 		dep->endpoint.desc = NULL;
 	}
 
-	dwc3_remove_requests(dwc, dep);
-
-	dep->stream_capable = false;
-	dep->type = 0;
-	dep->flags = 0;
-
 	return 0;
 }
 
@@ -1133,11 +1202,14 @@
 	 * pending to be processed by the driver.
 	 */
 	if (dep->trb_enqueue == dep->trb_dequeue) {
+		struct dwc3_request *req;
+
 		/*
-		 * If there is any request remained in the started_list at
-		 * this point, that means there is no TRB available.
+		 * If there is any request remained in the started_list with
+		 * active TRBs at this point, then there is no TRB available.
 		 */
-		if (!list_empty(&dep->started_list))
+		req = next_request(&dep->started_list);
+		if (req && req->num_trbs)
 			return 0;
 
 		return DWC3_TRB_NUM - 1;
@@ -1152,17 +1224,49 @@
 	return trbs_left;
 }
 
-static void __dwc3_prepare_one_trb(struct dwc3_ep *dep, struct dwc3_trb *trb,
-		dma_addr_t dma, unsigned int length, unsigned int chain,
-		unsigned int node, unsigned int stream_id,
-		unsigned int short_not_ok, unsigned int no_interrupt,
-		unsigned int is_last, bool must_interrupt)
+/**
+ * dwc3_prepare_one_trb - setup one TRB from one request
+ * @dep: endpoint for which this request is prepared
+ * @req: dwc3_request pointer
+ * @trb_length: buffer size of the TRB
+ * @chain: should this TRB be chained to the next?
+ * @node: only for isochronous endpoints. First TRB needs different type.
+ * @use_bounce_buffer: set to use bounce buffer
+ * @must_interrupt: set to interrupt on TRB completion
+ */
+static void dwc3_prepare_one_trb(struct dwc3_ep *dep,
+		struct dwc3_request *req, unsigned int trb_length,
+		unsigned int chain, unsigned int node, bool use_bounce_buffer,
+		bool must_interrupt)
 {
+	struct dwc3_trb		*trb;
+	dma_addr_t		dma;
+	unsigned int		stream_id = req->request.stream_id;
+	unsigned int		short_not_ok = req->request.short_not_ok;
+	unsigned int		no_interrupt = req->request.no_interrupt;
+	unsigned int		is_last = req->request.is_last;
 	struct dwc3		*dwc = dep->dwc;
 	struct usb_gadget	*gadget = dwc->gadget;
 	enum usb_device_speed	speed = gadget->speed;
 
-	trb->size = DWC3_TRB_SIZE_LENGTH(length);
+	if (use_bounce_buffer)
+		dma = dep->dwc->bounce_addr;
+	else if (req->request.num_sgs > 0)
+		dma = sg_dma_address(req->start_sg);
+	else
+		dma = req->request.dma;
+
+	trb = &dep->trb_pool[dep->trb_enqueue];
+
+	if (!req->trb) {
+		dwc3_gadget_move_started_request(req);
+		req->trb = trb;
+		req->trb_dma = dwc3_trb_dma_offset(dep, trb);
+	}
+
+	req->num_trbs++;
+
+	trb->size = DWC3_TRB_SIZE_LENGTH(trb_length);
 	trb->bpl = lower_32_bits(dma);
 	trb->bph = upper_32_bits(dma);
 
@@ -1202,10 +1306,10 @@
 				unsigned int mult = 2;
 				unsigned int maxp = usb_endpoint_maxp(ep->desc);
 
-				if (length <= (2 * maxp))
+				if (req->request.length <= (2 * maxp))
 					mult--;
 
-				if (length <= maxp)
+				if (req->request.length <= maxp)
 					mult--;
 
 				trb->size |= DWC3_TRB_SIZE_PCM1(mult);
@@ -1214,8 +1318,8 @@
 			trb->ctrl = DWC3_TRBCTL_ISOCHRONOUS;
 		}
 
-		/* always enable Interrupt on Missed ISOC */
-		trb->ctrl |= DWC3_TRB_CTRL_ISP_IMI;
+		if (!no_interrupt && !chain)
+			trb->ctrl |= DWC3_TRB_CTRL_ISP_IMI;
 		break;
 
 	case USB_ENDPOINT_XFER_BULK:
@@ -1254,6 +1358,19 @@
 	if (usb_endpoint_xfer_bulk(dep->endpoint.desc) && dep->stream_capable)
 		trb->ctrl |= DWC3_TRB_CTRL_SID_SOFN(stream_id);
 
+	/*
+	 * As per data book 4.2.3.2TRB Control Bit Rules section
+	 *
+	 * The controller autonomously checks the HWO field of a TRB to determine if the
+	 * entire TRB is valid. Therefore, software must ensure that the rest of the TRB
+	 * is valid before setting the HWO field to '1'. In most systems, this means that
+	 * software must update the fourth DWORD of a TRB last.
+	 *
+	 * However there is a possibility of CPU re-ordering here which can cause
+	 * controller to observe the HWO bit set prematurely.
+	 * Add a write memory barrier to prevent CPU re-ordering.
+	 */
+	wmb();
 	trb->ctrl |= DWC3_TRB_CTRL_HWO;
 
 	dwc3_ep_inc_enq(dep);
@@ -1261,50 +1378,6 @@
 	trace_dwc3_prepare_trb(dep, trb);
 }
 
-/**
- * dwc3_prepare_one_trb - setup one TRB from one request
- * @dep: endpoint for which this request is prepared
- * @req: dwc3_request pointer
- * @trb_length: buffer size of the TRB
- * @chain: should this TRB be chained to the next?
- * @node: only for isochronous endpoints. First TRB needs different type.
- * @use_bounce_buffer: set to use bounce buffer
- * @must_interrupt: set to interrupt on TRB completion
- */
-static void dwc3_prepare_one_trb(struct dwc3_ep *dep,
-		struct dwc3_request *req, unsigned int trb_length,
-		unsigned int chain, unsigned int node, bool use_bounce_buffer,
-		bool must_interrupt)
-{
-	struct dwc3_trb		*trb;
-	dma_addr_t		dma;
-	unsigned int		stream_id = req->request.stream_id;
-	unsigned int		short_not_ok = req->request.short_not_ok;
-	unsigned int		no_interrupt = req->request.no_interrupt;
-	unsigned int		is_last = req->request.is_last;
-
-	if (use_bounce_buffer)
-		dma = dep->dwc->bounce_addr;
-	else if (req->request.num_sgs > 0)
-		dma = sg_dma_address(req->start_sg);
-	else
-		dma = req->request.dma;
-
-	trb = &dep->trb_pool[dep->trb_enqueue];
-
-	if (!req->trb) {
-		dwc3_gadget_move_started_request(req);
-		req->trb = trb;
-		req->trb_dma = dwc3_trb_dma_offset(dep, trb);
-	}
-
-	req->num_trbs++;
-
-	__dwc3_prepare_one_trb(dep, trb, dma, trb_length, chain, node,
-			stream_id, short_not_ok, no_interrupt, is_last,
-			must_interrupt);
-}
-
 static bool dwc3_needs_extra_trb(struct dwc3_ep *dep, struct dwc3_request *req)
 {
 	unsigned int maxp = usb_endpoint_maxp(dep->endpoint.desc);
@@ -1364,8 +1437,8 @@
 	struct scatterlist *s;
 	int		i;
 	unsigned int length = req->request.length;
-	unsigned int remaining = req->request.num_mapped_sgs
-		- req->num_queued_sgs;
+	unsigned int remaining = req->num_pending_sgs;
+	unsigned int num_queued_sgs = req->request.num_mapped_sgs - remaining;
 	unsigned int num_trbs = req->num_trbs;
 	bool needs_extra_trb = dwc3_needs_extra_trb(dep, req);
 
@@ -1373,7 +1446,7 @@
 	 * If we resume preparing the request, then get the remaining length of
 	 * the request and resume where we left off.
 	 */
-	for_each_sg(req->request.sg, s, req->num_queued_sgs, i)
+	for_each_sg(req->request.sg, s, num_queued_sgs, i)
 		length -= sg_dma_len(s);
 
 	for_each_sg(sg, s, remaining, i) {
@@ -1538,7 +1611,7 @@
 
 static void dwc3_gadget_ep_cleanup_cancelled_requests(struct dwc3_ep *dep);
 
-static int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep)
+int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep)
 {
 	struct dwc3_gadget_ep_cmd_params params;
 	struct dwc3_request		*req;
@@ -1609,6 +1682,13 @@
 	if (dep->stream_capable && req->request.is_last)
 		dep->flags |= DWC3_EP_WAIT_TRANSFER_COMPLETE;
 
+	if (starting && dep->stream_capable) {
+		req->stream_timeout_timer.expires = jiffies +
+				msecs_to_jiffies(STREAM_TIMEOUT_MS);
+		mod_timer(&req->stream_timeout_timer,
+			  req->stream_timeout_timer.expires);
+	}
+
 	return 0;
 }
 
@@ -1621,6 +1701,69 @@
 }
 
 /**
+ * __dwc3_stop_active_transfer - stop the current active transfer
+ * @dep: isoc endpoint
+ * @force: set forcerm bit in the command
+ * @interrupt: command complete interrupt after End Transfer command
+ *
+ * When setting force, the ForceRM bit will be set. In that case
+ * the controller won't update the TRB progress on command
+ * completion. It also won't clear the HWO bit in the TRB.
+ * The command will also not complete immediately in that case.
+ */
+static int __dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, bool interrupt)
+{
+	struct dwc3 *dwc = dep->dwc;
+	struct dwc3_gadget_ep_cmd_params params;
+	u32 cmd;
+	int ret;
+
+	cmd = DWC3_DEPCMD_ENDTRANSFER;
+	cmd |= force ? DWC3_DEPCMD_HIPRI_FORCERM : 0;
+	cmd |= interrupt ? DWC3_DEPCMD_CMDIOC : 0;
+	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
+	memset(&params, 0, sizeof(params));
+	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
+	/*
+	 * If the End Transfer command was timed out while the device is
+	 * not in SETUP phase, it's possible that an incoming Setup packet
+	 * may prevent the command's completion. Let's retry when the
+	 * ep0state returns to EP0_SETUP_PHASE.
+	 */
+	if (ret == -ETIMEDOUT && dep->dwc->ep0state != EP0_SETUP_PHASE) {
+		dep->flags |= DWC3_EP_DELAY_STOP;
+		return 0;
+	}
+	WARN_ON_ONCE(ret);
+
+	/*
+	 * when transfer is stopped with force rm bit false, it can be
+	 * restarted by passing resource_index in params; don't loose it
+	 */
+	if (force)
+		dep->resource_index = 0;
+
+	if (!interrupt) {
+		if (!DWC3_IP_IS(DWC3) || DWC3_VER_IS_PRIOR(DWC3, 310A))
+			mdelay(1);
+		dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
+	} else if (!ret) {
+		dep->flags |= DWC3_EP_END_TRANSFER_PENDING;
+	}
+
+	dep->flags &= ~DWC3_EP_DELAY_STOP;
+
+	/*
+	 * when transfer is stopped with force rm bit false, it can be
+	 * restarted by passing resource_index in params; don't loose it
+	 */
+	if (force)
+		dep->resource_index = 0;
+
+	return ret;
+}
+
+/**
  * dwc3_gadget_start_isoc_quirk - workaround invalid frame number
  * @dep: isoc endpoint
  *
@@ -1683,6 +1826,7 @@
 
 		params.param0 = upper_32_bits(dep->dwc->bounce_addr);
 		params.param1 = lower_32_bits(dep->dwc->bounce_addr);
+		params.param2 = 0;
 
 		cmd = DWC3_DEPCMD_STARTTRANSFER;
 		cmd |= DWC3_DEPCMD_PARAM(test_frame_number);
@@ -1789,25 +1933,13 @@
 	 * status, issue END_TRANSFER command and retry on the next XferNotReady
 	 * event.
 	 */
-	if (ret == -EAGAIN) {
-		struct dwc3_gadget_ep_cmd_params params;
-		u32 cmd;
-
-		cmd = DWC3_DEPCMD_ENDTRANSFER |
-			DWC3_DEPCMD_CMDIOC |
-			DWC3_DEPCMD_PARAM(dep->resource_index);
-
-		dep->resource_index = 0;
-		memset(&params, 0, sizeof(params));
-
-		ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
-		if (!ret)
-			dep->flags |= DWC3_EP_END_TRANSFER_PENDING;
-	}
+	if (ret == -EAGAIN)
+		ret = __dwc3_stop_active_transfer(dep, false, true);
 
 	return ret;
 }
 
+static void dwc3_gadget_wakeup_interrupt(struct dwc3 *dwc);
 static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 {
 	struct dwc3		*dwc = dep->dwc;
@@ -1832,6 +1964,10 @@
 	req->request.actual	= 0;
 	req->request.status	= -EINPROGRESS;
 
+	if (dep->stream_capable)
+		timer_setup(&req->stream_timeout_timer,
+			    stream_timeout_function, 0);
+
 	trace_dwc3_ep_queue(req);
 
 	list_add_tail(&req->list, &dep->pending_list);
@@ -1846,11 +1982,19 @@
 	 */
 	if ((dep->flags & DWC3_EP_END_TRANSFER_PENDING) ||
 	    (dep->flags & DWC3_EP_WEDGE) ||
+	    (dep->flags & DWC3_EP_DELAY_STOP) ||
 	    (dep->flags & DWC3_EP_STALL)) {
 		dep->flags |= DWC3_EP_DELAY_START;
 		return 0;
 	}
 
+	/* If core is hibernated, need to wakeup (remote wakeup) */
+	if (dwc->is_hibernated) {
+		dwc->force_hiber_wake = true;
+		dwc3_gadget_exit_hibernation(dwc);
+		dwc->force_hiber_wake = false;
+	}
+
 	/*
 	 * NOTICE: Isochronous endpoints should NEVER be prestarted. We must
 	 * wait for a XferNotReady event so we will know what's the current
@@ -1864,9 +2008,20 @@
 				!(dep->flags & DWC3_EP_TRANSFER_STARTED))
 			return 0;
 
-		if ((dep->flags & DWC3_EP_PENDING_REQUEST)) {
-			if (!(dep->flags & DWC3_EP_TRANSFER_STARTED))
-				return __dwc3_gadget_start_isoc(dep);
+		if (dep->flags & DWC3_EP_PENDING_REQUEST) {
+			if (dep->flags & DWC3_EP_TRANSFER_STARTED) {
+				/*
+				 * If there are not entries in request list
+				 * then PENDING flag would be set, so that END
+				 * TRANSFER is issued when an entry is added
+				 * into request list.
+				 */
+				dwc3_stop_active_transfer(dep, true, true);
+				dep->flags = DWC3_EP_ENABLED;
+			}
+
+			/* Rest is taken care by DWC3_DEPEVT_XFERNOTREADY */
+			return 0;
 		}
 	}
 
@@ -1925,10 +2080,10 @@
 static void dwc3_gadget_ep_cleanup_cancelled_requests(struct dwc3_ep *dep)
 {
 	struct dwc3_request		*req;
-	struct dwc3_request		*tmp;
 	struct dwc3			*dwc = dep->dwc;
 
-	list_for_each_entry_safe(req, tmp, &dep->cancelled_list, list) {
+	while (!list_empty(&dep->cancelled_list)) {
+		req = next_request(&dep->cancelled_list);
 		dwc3_gadget_ep_skip_trbs(dep, req);
 		switch (req->status) {
 		case DWC3_REQUEST_STATUS_DISCONNECTED:
@@ -1945,6 +2100,12 @@
 			dwc3_gadget_giveback(dep, req, -ECONNRESET);
 			break;
 		}
+		/*
+		 * The endpoint is disabled, let the dwc3_remove_requests()
+		 * handle the cleanup.
+		 */
+		if (!dep->endpoint.desc)
+			break;
 	}
 }
 
@@ -1964,6 +2125,9 @@
 
 	spin_lock_irqsave(&dwc->lock, flags);
 
+	if (dep->stream_capable && timer_pending(&req->stream_timeout_timer))
+		del_timer(&req->stream_timeout_timer);
+
 	list_for_each_entry(r, &dep->cancelled_list, list) {
 		if (r == req)
 			goto out;
@@ -1971,7 +2135,17 @@
 
 	list_for_each_entry(r, &dep->pending_list, list) {
 		if (r == req) {
-			dwc3_gadget_giveback(dep, req, -ECONNRESET);
+			/*
+			 * Explicitly check for EP0/1 as dequeue for those
+			 * EPs need to be handled differently.  Control EP
+			 * only deals with one USB req, and giveback will
+			 * occur during dwc3_ep0_stall_and_restart().  EP0
+			 * requests are never added to started_list.
+			 */
+			if (dep->number > 1)
+				dwc3_gadget_giveback(dep, req, -ECONNRESET);
+			else
+				dwc3_ep0_reset_state(dwc);
 			goto out;
 		}
 	}
@@ -2063,7 +2237,8 @@
 		list_for_each_entry_safe(req, tmp, &dep->started_list, list)
 			dwc3_gadget_move_cancelled_request(req, DWC3_REQUEST_STATUS_STALLED);
 
-		if (dep->flags & DWC3_EP_END_TRANSFER_PENDING) {
+		if (dep->flags & DWC3_EP_END_TRANSFER_PENDING ||
+		    (dep->flags & DWC3_EP_DELAY_STOP)) {
 			dep->flags |= DWC3_EP_PENDING_CLEAR_STALL;
 			return 0;
 		}
@@ -2264,7 +2439,7 @@
 		if (!dep)
 			continue;
 
-		dwc3_remove_requests(dwc, dep);
+		dwc3_remove_requests(dwc, dep, -ESHUTDOWN);
 	}
 }
 
@@ -2361,14 +2536,42 @@
 	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
 }
 
-static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
+int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
 {
 	u32			reg;
-	u32			timeout = 500;
+	u32			timeout = 2000;
+	u32			saved_config = 0;
 
 	if (pm_runtime_suspended(dwc->dev))
 		return 0;
 
+	/*
+	 * When operating in USB 2.0 speeds (HS/FS), ensure that
+	 * GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
+	 * or stopping the controller. This resolves timeout issues that occur
+	 * during frequent role switches between host and device modes.
+	 *
+	 * Save and clear these settings, then restore them after completing the
+	 * controller start or stop sequence.
+	 *
+	 * This solution was discovered through experimentation as it is not
+	 * mentioned in the dwc3 programming guide. It has been tested on an
+	 * Exynos platforms.
+	 */
+	reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
+	if (reg & DWC3_GUSB2PHYCFG_SUSPHY) {
+		saved_config |= DWC3_GUSB2PHYCFG_SUSPHY;
+		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
+	}
+
+	if (reg & DWC3_GUSB2PHYCFG_ENBLSLPM) {
+		saved_config |= DWC3_GUSB2PHYCFG_ENBLSLPM;
+		reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
+	}
+
+	if (saved_config)
+		dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	if (is_on) {
 		if (DWC3_VER_IS_WITHIN(DWC3, ANY, 187A)) {
@@ -2380,59 +2583,135 @@
 			reg &= ~DWC3_DCTL_KEEP_CONNECT;
 		reg |= DWC3_DCTL_RUN_STOP;
 
-		if (dwc->has_hibernation)
-			reg |= DWC3_DCTL_KEEP_CONNECT;
-
 		__dwc3_gadget_set_speed(dwc);
 		dwc->pullups_connected = true;
 	} else {
 		reg &= ~DWC3_DCTL_RUN_STOP;
 
-		if (dwc->has_hibernation && !suspend)
-			reg &= ~DWC3_DCTL_KEEP_CONNECT;
-
 		dwc->pullups_connected = false;
 	}
 
 	dwc3_gadget_dctl_write_safe(dwc, reg);
 
 	do {
+		usleep_range(1000, 2000);
 		reg = dwc3_readl(dwc->regs, DWC3_DSTS);
 		reg &= DWC3_DSTS_DEVCTRLHLT;
 	} while (--timeout && !(!is_on ^ !reg));
 
+	if (saved_config) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
+		reg |= saved_config;
+		dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+	}
+
 	if (!timeout)
 		return -ETIMEDOUT;
 
 	return 0;
 }
 
-static void dwc3_gadget_disable_irq(struct dwc3 *dwc);
+void dwc3_gadget_disable_irq(struct dwc3 *dwc);
 static void __dwc3_gadget_stop(struct dwc3 *dwc);
 static int __dwc3_gadget_start(struct dwc3 *dwc);
 
-static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
+static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
 {
-	struct dwc3		*dwc = gadget_to_dwc(g);
-	unsigned long		flags;
-	int			ret;
+	unsigned long flags;
+	int ret;
 
-	is_on = !!is_on;
+	spin_lock_irqsave(&dwc->lock, flags);
+	if (!dwc->pullups_connected) {
+		spin_unlock_irqrestore(&dwc->lock, flags);
+		return 0;
+	}
+
+	dwc->connected = false;
+
+	/*
+	 * Attempt to end pending SETUP status phase, and not wait for the
+	 * function to do so.
+	 */
+	if (dwc->delayed_status)
+		dwc3_ep0_send_delayed_status(dwc);
+
+	/*
+	 * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
+	 * Section 4.1.8 Table 4-7, it states that for a device-initiated
+	 * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
+	 * command for any active transfers" before clearing the RunStop
+	 * bit.
+	 */
+	dwc3_stop_active_transfers(dwc);
+	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	/*
 	 * Per databook, when we want to stop the gadget, if a control transfer
 	 * is still in process, complete it and get the core into setup phase.
+	 * In case the host is unresponsive to a SETUP transaction, forcefully
+	 * stall the transfer, and move back to the SETUP phase, so that any
+	 * pending endxfers can be executed.
 	 */
-	if (!is_on && dwc->ep0state != EP0_SETUP_PHASE) {
+	if (dwc->ep0state != EP0_SETUP_PHASE) {
 		reinit_completion(&dwc->ep0_in_setup);
 
 		ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
 				msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
-		if (ret == 0)
-			dev_warn(dwc->dev, "timed out waiting for SETUP phase\n");
+		if (ret == 0) {
+			dev_warn(dwc->dev, "wait for SETUP phase timed out\n");
+			spin_lock_irqsave(&dwc->lock, flags);
+			dwc3_ep0_reset_state(dwc);
+			spin_unlock_irqrestore(&dwc->lock, flags);
+		}
 	}
 
 	/*
+	 * Note: if the GEVNTCOUNT indicates events in the event buffer, the
+	 * driver needs to acknowledge them before the controller can halt.
+	 * Simply let the interrupt handler acknowledges and handle the
+	 * remaining event generated by the controller while polling for
+	 * DSTS.DEVCTLHLT.
+	 */
+	ret = dwc3_gadget_run_stop(dwc, false, false);
+
+	/*
+	 * Stop the gadget after controller is halted, so that if needed, the
+	 * events to update EP0 state can still occur while the run/stop
+	 * routine polls for the halted state.  DEVTEN is cleared as part of
+	 * gadget stop.
+	 */
+	spin_lock_irqsave(&dwc->lock, flags);
+	__dwc3_gadget_stop(dwc);
+	spin_unlock_irqrestore(&dwc->lock, flags);
+
+	return ret;
+}
+
+static int dwc3_gadget_soft_connect(struct dwc3 *dwc)
+{
+	/*
+	 * In the Synopsys DWC_usb31 1.90a programming guide section
+	 * 4.1.9, it specifies that for a reconnect after a
+	 * device-initiated disconnect requires a core soft reset
+	 * (DCTL.CSftRst) before enabling the run/stop bit.
+	 */
+	dwc3_core_soft_reset(dwc);
+
+	dwc3_event_buffers_setup(dwc);
+	__dwc3_gadget_start(dwc);
+	return dwc3_gadget_run_stop(dwc, true, false);
+}
+
+static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
+{
+	struct dwc3		*dwc = gadget_to_dwc(g);
+	int			ret;
+
+	is_on = !!is_on;
+
+	dwc->softconnect = is_on;
+
+	/*
 	 * Avoid issuing a runtime resume if the device is already in the
 	 * suspended state during gadget disconnect.  DWC3 gadget was already
 	 * halted/stopped during runtime suspend.
@@ -2451,59 +2730,29 @@
 	ret = pm_runtime_get_sync(dwc->dev);
 	if (!ret || ret < 0) {
 		pm_runtime_put(dwc->dev);
-		return 0;
+		if (ret < 0)
+			pm_runtime_set_suspended(dwc->dev);
+		return ret;
 	}
 
-	/*
-	 * Synchronize and disable any further event handling while controller
-	 * is being enabled/disabled.
-	 */
-	disable_irq(dwc->irq_gadget);
-
-	spin_lock_irqsave(&dwc->lock, flags);
-
-	if (!is_on) {
-		u32 count;
-
-		dwc->connected = false;
-		/*
-		 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
-		 * Section 4.1.8 Table 4-7, it states that for a device-initiated
-		 * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
-		 * command for any active transfers" before clearing the RunStop
-		 * bit.
-		 */
-		dwc3_stop_active_transfers(dwc);
-		__dwc3_gadget_stop(dwc);
-
-		/*
-		 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
-		 * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the
-		 * "software needs to acknowledge the events that are generated
-		 * (by writing to GEVNTCOUNTn) while it is waiting for this bit
-		 * to be set to '1'."
-		 */
-		count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
-		count &= DWC3_GEVNTCOUNT_MASK;
-		if (count > 0) {
-			dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
-			dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
-						dwc->ev_buf->length;
-		}
-	} else {
-		__dwc3_gadget_start(dwc);
+	if (dwc->pullups_connected == is_on) {
+		pm_runtime_put(dwc->dev);
+		return 0;
 	}
 
-	ret = dwc3_gadget_run_stop(dwc, is_on, false);
-	spin_unlock_irqrestore(&dwc->lock, flags);
-	enable_irq(dwc->irq_gadget);
+	synchronize_irq(dwc->irq_gadget);
+
+	if (!is_on)
+		ret = dwc3_gadget_soft_disconnect(dwc);
+	else
+		ret = dwc3_gadget_soft_connect(dwc);
 
 	pm_runtime_put(dwc->dev);
 
 	return ret;
 }
 
-static void dwc3_gadget_enable_irq(struct dwc3 *dwc)
+void dwc3_gadget_enable_irq(struct dwc3 *dwc)
 {
 	u32			reg;
 
@@ -2516,6 +2765,10 @@
 			DWC3_DEVTEN_USBRSTEN |
 			DWC3_DEVTEN_DISCONNEVTEN);
 
+	/* Enable hibernation IRQ */
+	if (dwc->has_hibernation)
+		reg |= DWC3_DEVTEN_HIBERNATIONREQEVTEN;
+
 	if (DWC3_VER_IS_PRIOR(DWC3, 250A))
 		reg |= DWC3_DEVTEN_ULSTCNGEN;
 
@@ -2526,7 +2779,7 @@
 	dwc3_writel(dwc->regs, DWC3_DEVTEN, reg);
 }
 
-static void dwc3_gadget_disable_irq(struct dwc3 *dwc)
+void dwc3_gadget_disable_irq(struct dwc3 *dwc)
 {
 	/* mask all interrupts */
 	dwc3_writel(dwc->regs, DWC3_DEVTEN, 0x00);
@@ -2621,6 +2874,16 @@
 	reg |= DWC3_DCFG_IGNSTRMPP;
 	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
 
+	/* For OTG mode, check if the core is currently in Host mode.
+	 * This is not an error condition as there are times when the core is
+	 * working as host and kernel is told to initiate bind operation with
+	 * gadget class driver module.
+	 * The below remaining operations are handled in OTG driver whenever
+	 * required.
+	 */
+	if (dwc3_readl(dwc->regs, DWC3_GSTS) & DWC3_GSTS_CUR_MODE)
+		return 0;
+
 	/* Start with SuperSpeed Default */
 	dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
 
@@ -2640,11 +2903,13 @@
 
 	/* begin to receive SETUP packets */
 	dwc->ep0state = EP0_SETUP_PHASE;
+	dwc->ep0_bounced = false;
 	dwc->link_state = DWC3_LINK_STATE_SS_DIS;
 	dwc->delayed_status = false;
 	dwc3_ep0_out_start(dwc);
 
 	dwc3_gadget_enable_irq(dwc);
+	dwc3_enable_susphy(dwc, true);
 
 	return 0;
 
@@ -2655,6 +2920,7 @@
 	return ret;
 }
 
+static irqreturn_t dwc3_wakeup_interrupt(int irq, void *_dwc);
 static int dwc3_gadget_start(struct usb_gadget *g,
 		struct usb_gadget_driver *driver)
 {
@@ -2672,6 +2938,20 @@
 		return ret;
 	}
 
+	/* Look for wakeup interrupt if hibernation is supported */
+	if (dwc->has_hibernation) {
+		irq = dwc->irq_wakeup;
+		ret = devm_request_irq(dwc->dev, irq, dwc3_wakeup_interrupt,
+				       IRQF_SHARED, "usb-wakeup", dwc);
+
+		if (ret) {
+			dev_err(dwc->dev, "failed to request wakeup irq #%d --> %d\n",
+				irq, ret);
+			free_irq(dwc->irq_gadget, dwc);
+			return ret;
+		}
+	}
+
 	spin_lock_irqsave(&dwc->lock, flags);
 	dwc->gadget_driver	= driver;
 	spin_unlock_irqrestore(&dwc->lock, flags);
@@ -3051,9 +3331,7 @@
 			list_del(&dep->endpoint.ep_list);
 		}
 
-		debugfs_remove_recursive(debugfs_lookup(dep->name,
-				debugfs_lookup(dev_name(dep->dwc->dev),
-					       usb_debug_root)));
+		dwc3_debugfs_remove_endpoint_dir(dep);
 		kfree(dep);
 	}
 }
@@ -3117,7 +3395,15 @@
 	if (event->status & DEPEVT_STATUS_SHORT && !chain)
 		return 1;
 
-	if ((trb->ctrl & DWC3_TRB_CTRL_IOC) ||
+	if ((trb->ctrl & DWC3_TRB_CTRL_ISP_IMI) &&
+	    DWC3_TRB_SIZE_TRBSTS(trb->size) == DWC3_TRBSTS_MISSED_ISOC)
+		return 1;
+
+	if ((event->status & DEPEVT_STATUS_IOC) &&
+	    (trb->ctrl & DWC3_TRB_CTRL_IOC))
+		return 1;
+
+	if ((event->status & DEPEVT_STATUS_LST) &&
 	    (trb->ctrl & DWC3_TRB_CTRL_LST))
 		return 1;
 
@@ -3169,6 +3455,7 @@
 		const struct dwc3_event_depevt *event,
 		struct dwc3_request *req, int status)
 {
+	int request_status;
 	int ret;
 
 	if (req->request.num_mapped_sgs)
@@ -3189,6 +3476,45 @@
 		req->needs_extra_trb = false;
 	}
 
+	/*
+	 * The event status only reflects the status of the TRB with IOC set.
+	 * For the requests that don't set interrupt on completion, the driver
+	 * needs to check and return the status of the completed TRBs associated
+	 * with the request. Use the status of the last TRB of the request.
+	 */
+	if (req->request.no_interrupt) {
+		struct dwc3_trb *trb;
+
+		trb = dwc3_ep_prev_trb(dep, dep->trb_dequeue);
+		switch (DWC3_TRB_SIZE_TRBSTS(trb->size)) {
+		case DWC3_TRBSTS_MISSED_ISOC:
+			/* Isoc endpoint only */
+			request_status = -EXDEV;
+			break;
+		case DWC3_TRB_STS_XFER_IN_PROG:
+			/* Applicable when End Transfer with ForceRM=0 */
+		case DWC3_TRBSTS_SETUP_PENDING:
+			/* Control endpoint only */
+		case DWC3_TRBSTS_OK:
+		default:
+			request_status = 0;
+			break;
+		}
+	} else {
+		request_status = status;
+	}
+
+	req->request.actual = req->request.length - req->remaining;
+
+	if ((!dwc3_gadget_ep_request_completed(req) &&
+	     req->num_pending_sgs) || req->num_pending_sgs) {
+		if (!(event->status &
+			(DEPEVT_STATUS_SHORT | DEPEVT_STATUS_LST))) {
+			__dwc3_gadget_kick_transfer(dep);
+			goto out;
+		}
+	}
+
 	dwc3_gadget_giveback(dep, req, status);
 
 out:
@@ -3199,15 +3525,21 @@
 		const struct dwc3_event_depevt *event, int status)
 {
 	struct dwc3_request	*req;
-	struct dwc3_request	*tmp;
 
-	list_for_each_entry_safe(req, tmp, &dep->started_list, list) {
+	while (!list_empty(&dep->started_list)) {
 		int ret;
 
+		req = next_request(&dep->started_list);
 		ret = dwc3_gadget_ep_cleanup_completed_request(dep, event,
 				req, status);
 		if (ret)
 			break;
+		/*
+		 * The endpoint is disabled, let the dwc3_remove_requests()
+		 * handle the cleanup.
+		 */
+		if (!dep->endpoint.desc)
+			break;
 	}
 }
 
@@ -3248,14 +3580,28 @@
 
 	dwc3_gadget_ep_cleanup_completed_requests(dep, event, status);
 
+	if (dep->stream_capable && !list_empty(&dep->started_list))
+		__dwc3_gadget_kick_transfer(dep);
+
 	if (dep->flags & DWC3_EP_END_TRANSFER_PENDING)
 		goto out;
 
+	if (!dep->endpoint.desc)
+		return no_started_trb;
+
 	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
-		list_empty(&dep->started_list) &&
-		(list_empty(&dep->pending_list) || status == -EXDEV))
-		dwc3_stop_active_transfer(dep, true, true);
-	else if (dwc3_gadget_ep_should_continue(dep))
+	    list_empty(&dep->started_list)) {
+		if (list_empty(&dep->pending_list))
+			/*
+			 * If there is no entry in request list then do
+			 * not issue END TRANSFER now. Just set PENDING
+			 * flag, so that END TRANSFER is issued when an
+			 * entry is added into request list.
+			 */
+			dep->flags |= DWC3_EP_PENDING_REQUEST;
+		else if (status == -EXDEV)
+			dwc3_stop_active_transfer(dep, true, true);
+	} else if (dwc3_gadget_ep_should_continue(dep))
 		if (__dwc3_gadget_kick_transfer(dep) == 0)
 			no_started_trb = false;
 
@@ -3293,13 +3639,17 @@
 {
 	int status = 0;
 
+	if (!dep->endpoint.desc)
+		return;
+
 	if (usb_endpoint_xfer_isoc(dep->endpoint.desc))
 		dwc3_gadget_endpoint_frame_from_event(dep, event);
 
 	if (event->status & DEPEVT_STATUS_BUSERR)
 		status = -ECONNRESET;
 
-	if (event->status & DEPEVT_STATUS_MISSED_ISOC)
+	if ((event->status & DEPEVT_STATUS_MISSED_ISOC) &&
+	    usb_endpoint_xfer_isoc(dep->endpoint.desc))
 		status = -EXDEV;
 
 	dwc3_gadget_endpoint_trbs_complete(dep, event, status);
@@ -3346,6 +3696,14 @@
 	if (cmd != DWC3_DEPCMD_ENDTRANSFER)
 		return;
 
+	/*
+	 * The END_TRANSFER command will cause the controller to generate a
+	 * NoStream Event, and it's not due to the host DP NoStream rejection.
+	 * Ignore the next NoStream event.
+	 */
+	if (dep->stream_capable)
+		dep->flags |= DWC3_EP_IGNORE_NEXT_NOSTREAM;
+
 	dep->flags &= ~DWC3_EP_END_TRANSFER_PENDING;
 	dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
 	dwc3_gadget_ep_cleanup_cancelled_requests(dep);
@@ -3378,10 +3736,24 @@
 static void dwc3_gadget_endpoint_stream_event(struct dwc3_ep *dep,
 		const struct dwc3_event_depevt *event)
 {
-	struct dwc3 *dwc = dep->dwc;
+	struct dwc3		*dwc = dep->dwc;
+	struct dwc3_request	*req;
+	u8			stream_id;
 
 	if (event->status == DEPEVT_STREAMEVT_FOUND) {
+		stream_id = event->parameters;
+
+		/* Check for req matching the streamid and delete the timer */
+		list_for_each_entry(req, &dep->started_list, list) {
+			if (req->request.stream_id == stream_id) {
+				if (timer_pending(&req->stream_timeout_timer))
+					del_timer(&req->stream_timeout_timer);
+				break;
+			}
+		}
+
 		dep->flags |= DWC3_EP_FIRST_STREAM_PRIMED;
+
 		goto out;
 	}
 
@@ -3406,6 +3778,7 @@
 	case DEPEVT_STREAM_NOSTREAM:
 		if ((dep->flags & DWC3_EP_IGNORE_NEXT_NOSTREAM) ||
 		    !(dep->flags & DWC3_EP_FORCE_RESTART_STREAM) ||
+		    !(dep->flags & DWC3_EP_END_TRANSFER_PENDING) ||
 		    !(dep->flags & DWC3_EP_WAIT_TRANSFER_COMPLETE))
 			break;
 
@@ -3420,7 +3793,7 @@
 		 * streams are updated, and the device controller will not be
 		 * triggered to generate ERDY to move the next stream data. To
 		 * workaround this and maintain compatibility with various
-		 * hosts, force to reinitate the stream until the host is ready
+		 * hosts, force to reinitiate the stream until the host is ready
 		 * instead of waiting for the host to prime the endpoint.
 		 */
 		if (DWC3_VER_IS_WITHIN(DWC32, 100A, ANY)) {
@@ -3472,6 +3845,8 @@
 		dwc3_gadget_endpoint_command_complete(dep, event);
 		break;
 	case DWC3_DEPEVT_XFERCOMPLETE:
+		if (!dep->stream_capable)
+			break;
 		dwc3_gadget_endpoint_transfer_complete(dep, event);
 		break;
 	case DWC3_DEPEVT_STREAMEVT:
@@ -3521,18 +3896,40 @@
 	}
 }
 
-static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
+void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 	bool interrupt)
 {
-	struct dwc3_gadget_ep_cmd_params params;
-	u32 cmd;
-	int ret;
+	struct dwc3 *dwc = dep->dwc;
+
+	/*
+	 * Only issue End Transfer command to the control endpoint of a started
+	 * Data Phase. Typically we should only do so in error cases such as
+	 * invalid/unexpected direction as described in the control transfer
+	 * flow of the programming guide.
+	 */
+	if (dep->number <= 1 && dwc->ep0state != EP0_DATA_PHASE)
+		return;
+
+	if (interrupt && (dep->flags & DWC3_EP_DELAY_STOP))
+		return;
 
 	if (!(dep->flags & DWC3_EP_TRANSFER_STARTED) ||
 	    (dep->flags & DWC3_EP_END_TRANSFER_PENDING))
 		return;
 
 	/*
+	 * If a Setup packet is received but yet to DMA out, the controller will
+	 * not process the End Transfer command of any endpoint. Polling of its
+	 * DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
+	 * timeout. Delay issuing the End Transfer command until the Setup TRB is
+	 * prepared.
+	 */
+	if (dwc->ep0state != EP0_SETUP_PHASE && !dwc->delayed_status) {
+		dep->flags |= DWC3_EP_DELAY_STOP;
+		return;
+	}
+
+	/*
 	 * NOTICE: We are violating what the Databook says about the
 	 * EndTransfer command. Ideally we would _always_ wait for the
 	 * EndTransfer Command Completion IRQ, but that's causing too
@@ -3556,30 +3953,14 @@
 	 * enabled, the EndTransfer command will have completed upon
 	 * returning from this function.
 	 *
-	 * This mode is NOT available on the DWC_usb31 IP.
-	 */
-
-	cmd = DWC3_DEPCMD_ENDTRANSFER;
-	cmd |= force ? DWC3_DEPCMD_HIPRI_FORCERM : 0;
-	cmd |= interrupt ? DWC3_DEPCMD_CMDIOC : 0;
-	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
-	memset(&params, 0, sizeof(params));
-	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
-	WARN_ON_ONCE(ret);
-	dep->resource_index = 0;
-
-	/*
-	 * The END_TRANSFER command will cause the controller to generate a
-	 * NoStream Event, and it's not due to the host DP NoStream rejection.
-	 * Ignore the next NoStream event.
+	 * This mode is NOT available on the DWC_usb31 IP.  In this
+	 * case, if the IOC bit is not set, then delay by 1ms
+	 * after issuing the EndTransfer command.  This allows for the
+	 * controller to handle the command completely before DWC3
+	 * remove requests attempts to unmap USB request buffers.
 	 */
-	if (dep->stream_capable)
-		dep->flags |= DWC3_EP_IGNORE_NEXT_NOSTREAM;
 
-	if (!interrupt)
-		dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
-	else
-		dep->flags |= DWC3_EP_END_TRANSFER_PENDING;
+	__dwc3_stop_active_transfer(dep, force, interrupt);
 }
 
 static void dwc3_clear_stall_all_ep(struct dwc3 *dwc)
@@ -3608,6 +3989,8 @@
 {
 	int			reg;
 
+	dwc->suspended = false;
+
 	dwc3_gadget_set_link_state(dwc, DWC3_LINK_STATE_RX_DET);
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
@@ -3615,19 +3998,39 @@
 	reg &= ~DWC3_DCTL_INITU2ENA;
 	dwc3_gadget_dctl_write_safe(dwc, reg);
 
+	dwc->connected = false;
+
 	dwc3_disconnect_gadget(dwc);
 
+	/* In USB 2.0, to avoid hibernation interrupt at the time of connection
+	 * clear DWC3_DCTL_KEEP_CONNECT bit.
+	 */
+	if (dwc->has_hibernation) {
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg &= ~DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	}
+
 	dwc->gadget->speed = USB_SPEED_UNKNOWN;
 	dwc->setup_packet_pending = false;
 	usb_gadget_set_state(dwc->gadget, USB_STATE_NOTATTACHED);
 
-	dwc->connected = false;
+	dwc3_ep0_reset_state(dwc);
+
+	/*
+	 * Request PM idle to address condition where usage count is
+	 * already decremented to zero, but waiting for the disconnect
+	 * interrupt to set dwc->connected to FALSE.
+	 */
+	pm_request_idle(dwc->dev);
 }
 
 static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
 {
 	u32			reg;
 
+	dwc->suspended = false;
+
 	/*
 	 * Ideally, dwc3_reset_gadget() would trigger the function
 	 * drivers to stop any active transfers through ep disable.
@@ -3668,7 +4071,29 @@
 			dwc3_gadget_disconnect_interrupt(dwc);
 	}
 
+	/*
+	 * To avoid hibernation interrupt at the time of connection on hot-plug
+	 * clear DWC3_DCTL_KEEP_CONNECT bit on gadget enumeration and disable
+	 * DWC3_GCTL_GBLHIBERNATIONEN hibernation interrupt.
+	 */
+	if (dwc->has_hibernation) {
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg &= ~DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+		reg = dwc3_readl(dwc->regs, DWC3_GCTL);
+		reg &= ~DWC3_GCTL_GBLHIBERNATIONEN;
+		dwc3_writel(dwc->regs, DWC3_GCTL, reg);
+	}
+
 	dwc3_reset_gadget(dwc);
+
+	/*
+	 * From SNPS databook section 8.1.2, the EP0 should be in setup
+	 * phase. So ensure that EP0 is in setup phase by issuing a stall
+	 * and restart if EP0 is not in setup phase.
+	 */
+	dwc3_ep0_reset_state(dwc);
+
 	/*
 	 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
 	 * Section 4.1.2 Table 4-2, it states that during a USB reset, the SW
@@ -3792,8 +4217,10 @@
 		WARN_ONCE(DWC3_VER_IS_PRIOR(DWC3, 240A) && dwc->has_lpm_erratum,
 				"LPM Erratum not available on dwc3 revisions < 2.40a\n");
 
-		if (dwc->has_lpm_erratum && !DWC3_VER_IS_PRIOR(DWC3, 240A))
+		if (dwc->has_lpm_erratum && !DWC3_VER_IS_PRIOR(DWC3, 240A)) {
+			reg &= ~DWC3_DCTL_NYET_THRES_MASK;
 			reg |= DWC3_DCTL_NYET_THRES(dwc->lpm_nyet_threshold);
+		}
 
 		dwc3_gadget_dctl_write_safe(dwc, reg);
 	} else {
@@ -3823,6 +4250,27 @@
 	}
 
 	/*
+	 * In USB 2.0, to avoid hibernation interrupt at the time of connection
+	 * set DWC3_DCTL_KEEP_CONNECT bit here
+	 */
+	if (dwc->has_hibernation) {
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg |= DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+
+		/*
+		 * WORKAROUND: In USB 2.0, before connection done early
+		 * hibernation interrupt occurred. To avoid early hibernation
+		 * event for gadget mode set DWC3_GCTL_GBLHIBERNATIONEN bit
+		 * after connection done instead of global core setup in
+		 * dwc3 core.
+		 */
+		reg = dwc3_readl(dwc->regs, DWC3_GCTL);
+		reg |= DWC3_GCTL_GBLHIBERNATIONEN;
+		dwc3_writel(dwc->regs, DWC3_GCTL, reg);
+	}
+
+	/*
 	 * Configure PHY via GUSB3PIPECTLn if required.
 	 *
 	 * Update GTXFIFOSIZn
@@ -3833,10 +4281,11 @@
 
 static void dwc3_gadget_wakeup_interrupt(struct dwc3 *dwc)
 {
-	/*
-	 * TODO take core out of low power mode when that's
-	 * implemented.
-	 */
+	dwc->suspended = false;
+
+	/* Take core out of low power mode. */
+	if (dwc->is_hibernated)
+		dwc3_gadget_exit_hibernation(dwc);
 
 	if (dwc->async_callbacks && dwc->gadget_driver->resume) {
 		spin_unlock(&dwc->lock);
@@ -3845,6 +4294,17 @@
 	}
 }
 
+static irqreturn_t dwc3_wakeup_interrupt(int irq, void *_dwc)
+{
+	struct dwc3 *dwc = (struct dwc3 *)_dwc;
+
+	spin_lock(&dwc->lock);
+	dwc3_gadget_wakeup_interrupt(dwc);
+	spin_unlock(&dwc->lock);
+
+	return IRQ_HANDLED;
+}
+
 static void dwc3_gadget_linksts_change_interrupt(struct dwc3 *dwc,
 		unsigned int evtinfo)
 {
@@ -3948,8 +4408,10 @@
 {
 	enum dwc3_link_state next = evtinfo & DWC3_LINK_STATE_MASK;
 
-	if (dwc->link_state != next && next == DWC3_LINK_STATE_U3)
+	if (!dwc->suspended && next == DWC3_LINK_STATE_U3) {
+		dwc->suspended = true;
 		dwc3_suspend_gadget(dwc);
+	}
 
 	dwc->link_state = next;
 }
@@ -3972,10 +4434,12 @@
 	 * STAR#9000546576: Device Mode Hibernation: Issue in USB 2.0
 	 * Device Fallback from SuperSpeed
 	 */
-	if (is_ss ^ (dwc->speed == USB_SPEED_SUPER))
+	if ((!!is_ss ^ (dwc->speed == USB_SPEED_SUPER)) &&
+	    (!(dwc->has_hibernation)))
 		return;
 
 	/* enter hibernation here */
+	dwc3_gadget_enter_hibernation(dwc);
 }
 
 static void dwc3_gadget_interrupt(struct dwc3 *dwc,
@@ -3995,26 +4459,15 @@
 		dwc3_gadget_wakeup_interrupt(dwc);
 		break;
 	case DWC3_DEVICE_EVENT_HIBER_REQ:
-		if (dev_WARN_ONCE(dwc->dev, !dwc->has_hibernation,
-					"unexpected hibernation event\n"))
-			break;
-
-		dwc3_gadget_hibernation_interrupt(dwc, event->event_info);
+		dev_WARN_ONCE(dwc->dev, true, "unexpected hibernation event\n");
 		break;
 	case DWC3_DEVICE_EVENT_LINK_STATUS_CHANGE:
 		dwc3_gadget_linksts_change_interrupt(dwc, event->event_info);
 		break;
 	case DWC3_DEVICE_EVENT_SUSPEND:
 		/* It changed to be suspend event for version 2.30a and above */
-		if (!DWC3_VER_IS_PRIOR(DWC3, 230A)) {
-			/*
-			 * Ignore suspend event until the gadget enters into
-			 * USB_STATE_CONFIGURED state.
-			 */
-			if (dwc->gadget->state >= USB_STATE_CONFIGURED)
-				dwc3_gadget_suspend_interrupt(dwc,
-						event->event_info);
-		}
+		if (!DWC3_VER_IS_PRIOR(DWC3, 230A))
+			dwc3_gadget_suspend_interrupt(dwc, event->event_info);
 		break;
 	case DWC3_DEVICE_EVENT_SOF:
 	case DWC3_DEVICE_EVENT_ERRATIC_ERROR:
@@ -4069,16 +4522,29 @@
 		 */
 		evt->lpos = (evt->lpos + 4) % evt->length;
 		left -= 4;
+
+		/* Stop processing any events after core is hibernated */
+		if (dwc->is_hibernated)
+			break;
 	}
 
 	evt->count = 0;
-	evt->flags &= ~DWC3_EVENT_PENDING;
 	ret = IRQ_HANDLED;
 
-	/* Unmask interrupt */
-	reg = dwc3_readl(dwc->regs, DWC3_GEVNTSIZ(0));
-	reg &= ~DWC3_GEVNTSIZ_INTMASK;
-	dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), reg);
+	/* Prevent interrupt generation when hibernated */
+	if (!dwc->is_hibernated) {
+		/* Unmask interrupt */
+		reg = dwc3_readl(dwc->regs, DWC3_GEVNTSIZ(0));
+		reg &= ~DWC3_GEVNTSIZ_INTMASK;
+		dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), reg);
+	}
+
+	evt->flags &= ~DWC3_EVENT_PENDING;
+	/*
+	 * Add an explicit write memory barrier to make sure that the update of
+	 * clearing DWC3_EVENT_PENDING is observed in dwc3_check_event_buf()
+	 */
+	wmb();
 
 	if (dwc->imod_interval) {
 		dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), DWC3_GEVNTCOUNT_EHB);
@@ -4095,9 +4561,11 @@
 	unsigned long flags;
 	irqreturn_t ret = IRQ_NONE;
 
+	local_bh_disable();
 	spin_lock_irqsave(&dwc->lock, flags);
 	ret = dwc3_process_event_buf(evt);
 	spin_unlock_irqrestore(&dwc->lock, flags);
+	local_bh_enable();
 
 	return ret;
 }
@@ -4110,12 +4578,21 @@
 	u32 reg;
 
 	if (pm_runtime_suspended(dwc->dev)) {
+		dwc->pending_events = true;
+		/*
+		 * Trigger runtime resume. The get() function will be balanced
+		 * after processing the pending events in dwc3_process_pending
+		 * events().
+		 */
 		pm_runtime_get(dwc->dev);
 		disable_irq_nosync(dwc->irq_gadget);
-		dwc->pending_events = true;
 		return IRQ_HANDLED;
 	}
 
+	/* Stop processing events after hibernated */
+	if (dwc->is_hibernated)
+		return IRQ_HANDLED;
+
 	/*
 	 * With PCIe legacy interrupt, test shows that top-half irq handler can
 	 * be called again after HW interrupt deassertion. Check if bottom-half
@@ -4159,7 +4636,7 @@
 static int dwc3_gadget_get_irq(struct dwc3 *dwc)
 {
 	struct platform_device *dwc3_pdev = to_platform_device(dwc->dev);
-	int irq;
+	int irq, irq_hiber;
 
 	irq = platform_get_irq_byname_optional(dwc3_pdev, "peripheral");
 	if (irq > 0)
@@ -4183,6 +4660,18 @@
 		irq = -EINVAL;
 
 out:
+	/* look for wakeup interrupt if hibernation is supported */
+	if (dwc->has_hibernation) {
+		irq_hiber = platform_get_irq_byname(dwc3_pdev, "hiber");
+		if (irq_hiber > 0) {
+			dwc->irq_wakeup = irq_hiber;
+		} else {
+			irq_hiber = platform_get_irq(dwc3_pdev, 2);
+			if (irq_hiber > 0)
+				dwc->irq_wakeup = irq_hiber;
+		}
+	}
+
 	return irq;
 }
 
@@ -4213,6 +4702,19 @@
 
 	dwc->irq_gadget = irq;
 
+	if (dwc->dr_mode == USB_DR_MODE_OTG) {
+		struct usb_phy *phy;
+
+		/* Switch otg to peripheral mode */
+		phy = usb_get_phy(USB_PHY_TYPE_USB3);
+		if (!IS_ERR(phy)) {
+			if (phy && phy->otg)
+				otg_set_peripheral(phy->otg,
+						(struct usb_gadget *)1);
+			usb_put_phy(phy);
+		}
+	}
+
 	dwc->ep0_trb = dma_alloc_coherent(dwc->sysdev,
 					  sizeof(*dwc->ep0_trb) * 2,
 					  &dwc->ep0_trb_addr, GFP_KERNEL);
@@ -4292,6 +4794,26 @@
 		goto err5;
 	}
 
+	if (dwc->dr_mode == USB_DR_MODE_OTG) {
+		struct usb_phy *phy;
+
+		phy = usb_get_phy(USB_PHY_TYPE_USB3);
+		if (!IS_ERR(phy)) {
+			if (phy && phy->otg) {
+				ret = otg_set_peripheral(phy->otg,
+						dwc->gadget);
+				if (ret) {
+					dev_err(dwc->dev,
+					"otg_set_peripheral failed\n");
+					usb_put_phy(phy);
+					goto err5;
+				}
+			} else {
+				usb_put_phy(phy);
+			}
+		}
+	}
+
 	if (DWC3_IP_IS(DWC32) && dwc->maximum_speed == USB_SPEED_SUPER_PLUS)
 		dwc3_gadget_set_ssp_rate(dwc->gadget, dwc->max_ssp_rate);
 	else
@@ -4326,6 +4848,7 @@
 	if (!dwc->gadget)
 		return;
 
+	dwc3_enable_susphy(dwc, false);
 	usb_del_gadget(dwc->gadget);
 	dwc3_gadget_free_endpoints(dwc);
 	usb_put_gadget(dwc->gadget);
@@ -4338,45 +4861,52 @@
 
 int dwc3_gadget_suspend(struct dwc3 *dwc)
 {
-	if (!dwc->gadget_driver)
-		return 0;
+	unsigned long flags;
+	int ret;
 
-	dwc3_gadget_run_stop(dwc, false, false);
-	dwc3_disconnect_gadget(dwc);
-	__dwc3_gadget_stop(dwc);
+	ret = dwc3_gadget_soft_disconnect(dwc);
+	if (ret)
+		goto err;
+
+	spin_lock_irqsave(&dwc->lock, flags);
+	if (dwc->gadget_driver)
+		dwc3_disconnect_gadget(dwc);
+	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	return 0;
+
+err:
+	/*
+	 * Attempt to reset the controller's state. Likely no
+	 * communication can be established until the host
+	 * performs a port reset.
+	 */
+	if (dwc->softconnect)
+		dwc3_gadget_soft_connect(dwc);
+
+	return ret;
 }
 
 int dwc3_gadget_resume(struct dwc3 *dwc)
 {
-	int			ret;
+	int			ret, reg;
 
-	if (!dwc->gadget_driver)
+	if (!dwc->gadget_driver || !dwc->softconnect)
 		return 0;
 
-	ret = __dwc3_gadget_start(dwc);
+	ret = dwc3_gadget_soft_connect(dwc);
 	if (ret < 0)
-		goto err0;
+		return ret;
 
-	ret = dwc3_gadget_run_stop(dwc, true, false);
-	if (ret < 0)
-		goto err1;
+	/*
+	 * In USB 2.0, to avoid hibernation interrupt at the time of connection
+	 * set DWC3_DCTL_KEEP_CONNECT bit.
+	 */
+	if (dwc->has_hibernation) {
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg |= DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	}
 
 	return 0;
-
-err1:
-	__dwc3_gadget_stop(dwc);
-
-err0:
-	return ret;
-}
-
-void dwc3_gadget_process_pending_events(struct dwc3 *dwc)
-{
-	if (dwc->pending_events) {
-		dwc3_interrupt(dwc->irq_gadget, dwc->ev_buf);
-		dwc->pending_events = false;
-		enable_irq(dwc->irq_gadget);
-	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/gadget.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/gadget.h
@@ -56,6 +56,15 @@
 
 /* Frame/Microframe Number Mask */
 #define DWC3_FRNUMBER_MASK		0x3fff
+
+/* Below used in hibernation */
+#define DWC3_NON_STICKY_RESTORE_RETRIES	500
+#define DWC3_NON_STICKY_SAVE_RETRIES	500
+#define DWC3_DEVICE_CTRL_READY_RETRIES	20000
+#define DWC3_NON_STICKY_RESTORE_DELAY	100
+#define DWC3_NON_STICKY_SAVE_DELAY	100
+#define DWC3_DEVICE_CTRL_READY_DELAY	5
+
 /* -------------------------------------------------------------------------- */
 
 #define to_dwc3_request(r)	(container_of(r, struct dwc3_request, request))
@@ -110,12 +119,26 @@
 void dwc3_ep0_interrupt(struct dwc3 *dwc,
 		const struct dwc3_event_depevt *event);
 void dwc3_ep0_out_start(struct dwc3 *dwc);
+void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep);
+void dwc3_ep0_stall_and_restart(struct dwc3 *dwc);
+void dwc3_gadget_enable_irq(struct dwc3 *dwc);
+void dwc3_gadget_disable_irq(struct dwc3 *dwc);
 int __dwc3_gadget_ep0_set_halt(struct usb_ep *ep, int value);
 int dwc3_gadget_ep0_set_halt(struct usb_ep *ep, int value);
 int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
 		gfp_t gfp_flags);
 int __dwc3_gadget_ep_set_halt(struct dwc3_ep *dep, int value, int protocol);
+int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action);
+int __dwc3_gadget_ep_disable(struct dwc3_ep *dep);
+int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep);
+void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
+		bool interrupt);
+int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend);
+dma_addr_t dwc3_trb_dma_offset(struct dwc3_ep *dep, struct dwc3_trb *trb);
+void dwc3_gadget_enter_hibernation(struct dwc3 *dwc);
+void dwc3_gadget_exit_hibernation(void *_dwc);
 void dwc3_ep0_send_delayed_status(struct dwc3 *dwc);
+void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, bool interrupt);
 
 /**
  * dwc3_gadget_ep_get_transfer_index - Gets transfer index from HW
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/gadget_hibernation.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/gadget_hibernation.c
@@ -0,0 +1,549 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * gadget_hibernation.c - DesignWare USB3 DRD Controller gadget hibernation file
+ *
+ * This file has routines to handle hibernation and wakeup events in gadget mode
+ *
+ * Author: Manish Narani <manish.narani@xilinx.com>
+ */
+
+#include "core.h"
+#include "gadget.h"
+#include "debug.h"
+#include "io.h"
+
+/* array of registers to save on hibernation and restore them on wakeup */
+static u32 save_reg_addr[] = {
+	DWC3_DCTL,
+	DWC3_DCFG,
+	DWC3_DEVTEN
+};
+
+/**
+ * save_regs - Saves registers on hibernation
+ * @dwc: pointer to our controller context structure
+ *
+ * Returns 0 on success otherwise negative errno.
+ */
+static int save_regs(struct dwc3 *dwc)
+{
+	int i;
+
+	if (!dwc->saved_regs) {
+		dwc->saved_regs = devm_kmalloc(dwc->dev,
+					       sizeof(save_reg_addr),
+					       GFP_KERNEL);
+		if (!dwc->saved_regs) {
+			dev_err(dwc->dev, "Not enough memory to save regs\n");
+			return -ENOMEM;
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(save_reg_addr); i++)
+		dwc->saved_regs[i] = dwc3_readl(dwc->regs,
+						save_reg_addr[i]);
+	return 0;
+}
+
+/**
+ * restore_regs - Restores registers on wakeup
+ * @dwc: pointer to our controller context structure
+ */
+static void restore_regs(struct dwc3 *dwc)
+{
+	int i;
+
+	if (!dwc->saved_regs) {
+		dev_warn(dwc->dev, "Regs not saved\n");
+		return;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(save_reg_addr); i++)
+		dwc3_writel(dwc->regs, save_reg_addr[i],
+			    dwc->saved_regs[i]);
+}
+
+/**
+ * restart_ep0_trans - Restarts EP0 transfer on wakeup
+ * @dwc: pointer to our controller context structure
+ * epnum: endpoint number
+ *
+ * Returns 0 on success otherwise negative errno.
+ */
+static int restart_ep0_trans(struct dwc3 *dwc, int epnum)
+{
+	struct dwc3_ep *dep = dwc->eps[epnum];
+	struct dwc3_trb *trb = dwc->ep0_trb;
+	struct dwc3_gadget_ep_cmd_params params;
+	int ret;
+	u32 cmd;
+
+	memset(&params, 0, sizeof(params));
+	params.param0 = upper_32_bits(dwc->ep0_trb_addr);
+	params.param1 = lower_32_bits(dwc->ep0_trb_addr);
+
+	/* set HWO bit back to 1 and restart transfer */
+	trb->ctrl |= DWC3_TRB_CTRL_HWO;
+
+	/* Clear the TRBSTS feild */
+	trb->size &= ~(0x0F << 28);
+
+	cmd = DWC3_DEPCMD_STARTTRANSFER | DWC3_DEPCMD_PARAM(0);
+	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
+	if (ret < 0) {
+		dev_err(dwc->dev, "failed to restart transfer on %s\n",
+			dep->name);
+		return ret;
+	}
+
+	dwc3_gadget_ep_get_transfer_index(dep);
+
+	return 0;
+}
+
+extern dma_addr_t dwc3_trb_dma_offset(struct dwc3_ep *dep,
+				      struct dwc3_trb *trb);
+/**
+ * restore_eps - Restores non EP0 eps in the same state as they were before
+ * hibernation
+ * @dwc: pointer to our controller context structure
+ *
+ * Returns 0 on success otherwise negative errno.
+ */
+static int restore_eps(struct dwc3 *dwc)
+{
+	int epnum, ret;
+
+	for (epnum = 2; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
+		/* Enable the endpoint */
+		struct dwc3_ep *dep = dwc->eps[epnum];
+
+		if (!dep)
+			continue;
+
+		if (!(dep->flags & DWC3_EP_ENABLED))
+			continue;
+
+		ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_RESTORE);
+		if (ret) {
+			dev_err(dwc->dev, "failed to enable %s\n", dep->name);
+			return ret;
+		}
+	}
+
+	for (epnum = 2; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
+		struct dwc3_ep *dep = dwc->eps[epnum];
+
+		if (!dep)
+			continue;
+
+		if (!(dep->flags & DWC3_EP_ENABLED))
+			continue;
+
+		if (dep->flags & DWC3_EP_STALL) {
+			/* Set stall for the endpoint */
+			struct dwc3_gadget_ep_cmd_params	params;
+
+			memset(&params, 0x00, sizeof(params));
+
+			ret = dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_SETSTALL,
+						      &params);
+			if (ret) {
+				dev_err(dwc->dev, "failed to set STALL on %s\n",
+					dep->name);
+				return ret;
+			}
+		} else {
+			u32 cmd;
+			struct dwc3_gadget_ep_cmd_params params;
+			struct dwc3_trb *trb;
+			u8 trb_dequeue = dep->trb_dequeue;
+
+			trb = &dep->trb_pool[trb_dequeue];
+
+			/*
+			 * check the last processed TRBSTS field has value
+			 * 4 (TRBInProgress), if yes resubmit the same TRB
+			 */
+			if (DWC3_TRB_SIZE_TRBSTS(trb->size) ==
+					DWC3_TRB_STS_XFER_IN_PROG) {
+				/* Set the HWO bit */
+				trb->ctrl |= DWC3_TRB_CTRL_HWO;
+
+				/* Clear the TRBSTS field */
+				trb->size &= ~(0x0F << 28);
+
+				memset(&params, 0, sizeof(params));
+
+				/* Issue starttransfer */
+				params.param0 =
+					upper_32_bits(dwc3_trb_dma_offset(dep,
+									  trb));
+				params.param1 =
+					lower_32_bits(dwc3_trb_dma_offset(dep,
+									  trb));
+
+				cmd = DWC3_DEPCMD_STARTTRANSFER |
+					DWC3_DEPCMD_PARAM(0);
+
+				dwc3_send_gadget_ep_cmd(dep, cmd, &params);
+			} else {
+				ret = __dwc3_gadget_kick_transfer(dep);
+				if (ret) {
+					dev_err(dwc->dev,
+						"%s: restart transfer failed\n",
+						dep->name);
+					return ret;
+				}
+			}
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * restore_ep0 - Restores EP0 in the same state as they were before hibernation
+ * @dwc: pointer to our controller context structure
+ *
+ * Returns 0 on success otherwise negative errno.
+ */
+static int restore_ep0(struct dwc3 *dwc)
+{
+	int epnum, ret;
+
+	for (epnum = 0; epnum < 2; epnum++) {
+		struct dwc3_ep *dep = dwc->eps[epnum];
+
+		if (!dep)
+			continue;
+
+		if (!(dep->flags & DWC3_EP_ENABLED))
+			continue;
+
+		ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_RESTORE);
+		if (ret) {
+			dev_err(dwc->dev, "failed to enable %s\n", dep->name);
+			return ret;
+		}
+
+		if (dep->flags & DWC3_EP_STALL) {
+			struct dwc3_gadget_ep_cmd_params        params;
+
+			memset(&params, 0x00, sizeof(params));
+
+			ret = dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_SETSTALL,
+						      &params);
+			if (ret) {
+				dev_err(dwc->dev, "failed to set STALL on %s\n",
+					dep->name);
+				return ret;
+			}
+		} else {
+			if (!dep->resource_index && epnum)
+				continue;
+
+			ret = restart_ep0_trans(dwc, epnum);
+			if (ret) {
+				dev_err(dwc->dev,
+					"failed to restart transfer on: %s\n",
+					dep->name);
+				return ret;
+			}
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * save_endpoint_state - Saves ep state on hibernation
+ * @dep: endpoint to get state
+ *
+ * Returns 0 on success otherwise negative errno.
+ */
+static int save_endpoint_state(struct dwc3_ep *dep)
+{
+	struct dwc3 *dwc = dep->dwc;
+	struct dwc3_gadget_ep_cmd_params params;
+	int ret;
+
+	memset(&params, 0, sizeof(params));
+	ret = dwc3_send_gadget_ep_cmd(dep, DWC3_DEPCMD_GETEPSTATE,
+				      &params);
+	if (ret) {
+		dev_err(dwc->dev, "Failed to get endpoint state on %s\n",
+			dep->name);
+		return ret;
+	}
+
+	dep->saved_state = dwc3_readl(dep->regs, DWC3_DEPCMDPAR2);
+	return 0;
+}
+
+/**
+ * dwc3_gadget_enter_hibernation - Interrupt handler of hibernation
+ * @dwc: pointer to our controller context structure
+ */
+void dwc3_gadget_enter_hibernation(struct dwc3 *dwc)
+{
+	u32 epnum, reg;
+	int retries, ret;
+
+	/* Check if the link state is valid before hibernating */
+	switch (dwc3_gadget_get_link_state(dwc)) {
+	case DWC3_LINK_STATE_U3:
+	case DWC3_LINK_STATE_SS_DIS:
+		break;
+	default:
+		dev_dbg(dwc->dev,
+			"%s: Got fake hiber event\n", __func__);
+		return;
+	}
+
+	/* stop all active transfers and save endpoint status */
+	for (epnum = 0; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
+		struct dwc3_ep *dep = dwc->eps[epnum];
+
+		if (!dep)
+			continue;
+
+		if (!(dep->flags & DWC3_EP_ENABLED))
+			continue;
+
+		if (dep->flags & DWC3_EP_TRANSFER_STARTED)
+			dwc3_stop_active_transfer(dep, false, true);
+
+		dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
+
+		save_endpoint_state(dep);
+	}
+
+	/* stop the controller */
+	dwc3_gadget_run_stop(dwc, false, true);
+
+	/* set the flag */
+	dwc->is_hibernated = true;
+
+	/*
+	 * ack events, don't process them; h/w decrements the count by the value
+	 * written
+	 */
+	reg = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
+	dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), reg);
+	dwc->ev_buf->count = 0;
+	dwc->ev_buf->flags &= ~DWC3_EVENT_PENDING;
+
+	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+
+	/* disable keep connect if we are disconnected right now */
+	if (dwc3_gadget_get_link_state(dwc) == DWC3_LINK_STATE_SS_DIS) {
+		reg &= ~DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	} else {
+		reg |= DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	}
+
+	/* save generic registers */
+	save_regs(dwc);
+
+	/* initiate controller save state */
+	reg |= DWC3_DCTL_CSS;
+	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+
+	/* wait till controller saves state */
+	retries = DWC3_NON_STICKY_SAVE_RETRIES;
+	do {
+		reg = dwc3_readl(dwc->regs, DWC3_DSTS);
+		if (!(reg & DWC3_DSTS_SSS))
+			break;
+
+		udelay(DWC3_NON_STICKY_SAVE_DELAY);
+	} while (--retries);
+
+	if (retries < 0) {
+		dev_err(dwc->dev, "USB core failed to save state\n");
+		goto err;
+	}
+
+	if (dwc->dwc3_pmu) {
+		ret = regulator_disable(dwc->dwc3_pmu);
+		if (ret) {
+			dev_err(dwc->dev,
+					"%s: %d Failed to enable dwc3_pmu supply\n",
+					__func__, __LINE__);
+			goto err;
+		}
+	}
+
+	dev_dbg(dwc->dev, "Hibernated!\n");
+	return;
+
+err:
+	dev_err(dwc->dev, "Fail in handling Hibernation Interrupt\n");
+	return;
+}
+
+/**
+ * dwc3_gadget_exit_hibernation - Interrupt handler of wakeup
+ * @dwc: pointer to our controller context structure
+ */
+void dwc3_gadget_exit_hibernation(void *_dwc)
+{
+	struct dwc3 *dwc = (struct dwc3 *)(_dwc);
+
+	u32 reg, link_state;
+	int ret, retries;
+	bool enter_hiber = false;
+
+	/* On USB 2.0 we observed back to back wakeup interrupts */
+	if (!dwc->is_hibernated) {
+		dev_dbg(dwc->dev, "Not in hibernated state\n");
+		goto err;
+	}
+
+	if (dwc->dwc3_pmu) {
+		ret = regulator_enable(dwc->dwc3_pmu);
+		if (ret) {
+			dev_err(dwc->dev,
+					"%s:%d: Failed to enable dwc3_pmu supply\n",
+					__func__, __LINE__);
+			goto err;
+		}
+	}
+
+	restore_regs(dwc);
+
+	/* Initialize the core and restore the saved registers */
+	dwc3_core_init(dwc);
+
+	/* ask controller to save the non-sticky registers */
+	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+	reg |= DWC3_DCTL_CRS;
+	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+
+	/* Wait till non-sticky registers are restored */
+	retries = DWC3_NON_STICKY_RESTORE_RETRIES;
+	do {
+		reg = dwc3_readl(dwc->regs, DWC3_DSTS);
+		if (!(reg & DWC3_DSTS_RSS))
+			break;
+
+		udelay(DWC3_NON_STICKY_RESTORE_DELAY);
+	} while (--retries);
+
+	if (retries < 0 || (reg & DWC3_DSTS_SRE)) {
+		dev_err(dwc->dev, "Failed to restore non-sticky regs\n");
+		goto err;
+	}
+
+	/* restore ep0 endpoints */
+	ret = restore_ep0(dwc);
+	if (ret) {
+		dev_err(dwc->dev, "Failed in restorig EP0 states\n");
+		goto err;
+	}
+
+	/* start the controller */
+	ret = dwc3_gadget_run_stop(dwc, true, false);
+	if (ret < 0) {
+		dev_err(dwc->dev, "USB core failed to start on wakeup\n");
+		goto err;
+	}
+
+	/* Wait until device controller is ready */
+	retries = DWC3_DEVICE_CTRL_READY_RETRIES;
+	while (--retries) {
+		reg = dwc3_readl(dwc->regs, DWC3_DSTS);
+		if (reg & DWC3_DSTS_DCNRD)
+			udelay(DWC3_DEVICE_CTRL_READY_DELAY);
+		else
+			break;
+	}
+
+	if (retries < 0) {
+		dev_err(dwc->dev, "USB core failed to restore controller\n");
+		goto err;
+	}
+
+	/*
+	 * As some suprious signals also cause wakeup event, wait for some time
+	 * and check the link state to confirm if the wakeup signal is real
+	 */
+	udelay(10);
+
+	link_state = dwc3_gadget_get_link_state(dwc);
+
+	/* check if the link state is in a valid state */
+	switch (link_state) {
+	case DWC3_LINK_STATE_RESET:
+		/* Reset devaddr */
+		reg = dwc3_readl(dwc->regs, DWC3_DCFG);
+		reg &= ~(DWC3_DCFG_DEVADDR_MASK);
+		dwc3_writel(dwc->regs, DWC3_DCFG, reg);
+
+		/* issue recovery on the link */
+		ret = dwc3_gadget_set_link_state(dwc, DWC3_LINK_STATE_RECOV);
+		if (ret < 0) {
+			dev_err(dwc->dev,
+				"Failed to set link state to Recovery\n");
+			goto err;
+		}
+
+		break;
+
+	case DWC3_LINK_STATE_SS_DIS:
+		/* Clear keep connect from reconnecting to HOST */
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg &= ~DWC3_DCTL_KEEP_CONNECT;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+		fallthrough;
+	case DWC3_LINK_STATE_U3:
+		/* Ignore wakeup event as the link is still in U3 state */
+		dev_dbg(dwc->dev, "False wakeup event %d\n", link_state);
+
+		if (!dwc->force_hiber_wake)
+			enter_hiber = true;
+		break;
+
+	default:
+		/* issue recovery on the link */
+		ret = dwc3_gadget_set_link_state(dwc, DWC3_LINK_STATE_RECOV);
+		if (ret < 0) {
+			dev_err(dwc->dev,
+				"Failed to set link state to Recovery\n");
+			goto err;
+		}
+
+		break;
+	}
+
+	if (link_state != DWC3_LINK_STATE_SS_DIS) {
+		/* Restore non EP0 EPs */
+		ret = restore_eps(dwc);
+		if (ret) {
+			dev_err(dwc->dev, "Failed restoring non-EP0 states\n");
+			goto err;
+		}
+	}
+
+	/* clear the flag */
+	dwc->is_hibernated = false;
+
+	if (enter_hiber) {
+		/*
+		 * as the wakeup was because of the spurious signals,
+		 * enter hibernation again
+		 */
+		dwc3_gadget_enter_hibernation(dwc);
+		return;
+	}
+
+	dev_dbg(dwc->dev, "We are back from hibernation!\n");
+	return;
+
+err:
+	dev_err(dwc->dev, "Fail in handling Wakeup Interrupt\n");
+	return;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/host.c
@@ -9,9 +9,46 @@
 
 #include <linux/acpi.h>
 #include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
 
+#include "../host/xhci-plat.h"
 #include "core.h"
 
+static void dwc3_xhci_plat_start(struct usb_hcd *hcd)
+{
+	struct platform_device *pdev;
+	struct dwc3 *dwc;
+
+	if (!usb_hcd_is_primary_hcd(hcd))
+		return;
+
+	pdev = to_platform_device(hcd->self.controller);
+	dwc = dev_get_drvdata(pdev->dev.parent);
+
+	dwc3_enable_susphy(dwc, true);
+}
+
+static const struct xhci_plat_priv dwc3_xhci_plat_quirk = {
+	.plat_start = dwc3_xhci_plat_start,
+};
+
+static dwc3_wakeup_t dwc3_wakeup_fn;
+
+ /* dwc3 host wakeup registration */
+void dwc3_host_wakeup_register(dwc3_wakeup_t func)
+{
+	dwc3_wakeup_fn = func;
+}
+
+/* callback function */
+void dwc3_host_wakeup_capable(struct device *dev, bool wakeup)
+{
+	if (dwc3_wakeup_fn)
+		dwc3_wakeup_fn(dev, wakeup);
+}
+
 static int dwc3_host_get_irq(struct dwc3 *dwc)
 {
 	struct platform_device	*dwc3_pdev = to_platform_device(dwc->dev);
@@ -44,7 +81,7 @@
 
 int dwc3_host_init(struct dwc3 *dwc)
 {
-	struct property_entry	props[4];
+	struct property_entry	props[6];
 	struct platform_device	*xhci;
 	int			ret, irq;
 	struct resource		*res;
@@ -89,12 +126,22 @@
 
 	memset(props, 0, sizeof(struct property_entry) * ARRAY_SIZE(props));
 
+	props[prop_idx++] = PROPERTY_ENTRY_BOOL("xhci-sg-trb-cache-size-quirk");
+
 	if (dwc->usb3_lpm_capable)
 		props[prop_idx++] = PROPERTY_ENTRY_BOOL("usb3-lpm-capable");
 
 	if (dwc->usb2_lpm_disable)
 		props[prop_idx++] = PROPERTY_ENTRY_BOOL("usb2-lpm-disable");
 
+	if (device_property_read_bool(&dwc3_pdev->dev,
+					"snps,xhci-stream-quirk"))
+		props[prop_idx++] = PROPERTY_ENTRY_BOOL("xhci-stream-quirk");
+
+	if (device_property_read_bool(&dwc3_pdev->dev,
+				      "snps,xhci-reset-on-resume"))
+		props[prop_idx++] = PROPERTY_ENTRY_BOOL("xhci-reset-on-resume");
+
 	/**
 	 * WORKAROUND: dwc3 revisions <=3.00a have a limitation
 	 * where Port Disable command doesn't work.
@@ -115,6 +162,29 @@
 		}
 	}
 
+	ret = platform_device_add_data(xhci, &dwc3_xhci_plat_quirk,
+				       sizeof(struct xhci_plat_priv));
+	if (ret)
+		goto err;
+
+	phy_create_lookup(dwc->usb2_generic_phy, "usb2-phy",
+			  dev_name(dwc->dev));
+	phy_create_lookup(dwc->usb3_generic_phy, "usb3-phy",
+			  dev_name(dwc->dev));
+
+	if (dwc->dr_mode == USB_DR_MODE_OTG) {
+
+		struct usb_phy *phy = usb_get_phy(USB_PHY_TYPE_USB3);
+
+		if (!IS_ERR(phy)) {
+			if (phy && phy->otg)
+				otg_set_host(phy->otg,
+					     (struct usb_bus *)0xdeadbeef);
+
+			usb_put_phy(phy);
+		}
+	}
+
 	ret = platform_device_add(xhci);
 	if (ret) {
 		dev_err(dwc->dev, "failed to register xHCI device\n");
@@ -129,5 +199,7 @@
 
 void dwc3_host_exit(struct dwc3 *dwc)
 {
+	dwc3_enable_susphy(dwc, false);
 	platform_device_unregister(dwc->xhci);
+	dwc->xhci = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/otg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/otg.c
@@ -0,0 +1,2190 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * otg.c - DesignWare USB3 DRD Controller OTG file
+ *
+ * Copyright (C) 2016 Xilinx, Inc. All rights reserved.
+ *
+ * Author:  Manish Narani <mnarani@xilinx.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/pci.h>
+#include <linux/slab.h>
+#include <linux/sched/signal.h>
+#include <linux/sched.h>
+#include <linux/freezer.h>
+#include <linux/kthread.h>
+#include <linux/version.h>
+#include <linux/sysfs.h>
+
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/phy.h>
+
+#include <../drivers/usb/host/xhci.h>
+#include "platform_data.h"
+#include "core.h"
+#include "gadget.h"
+#include "io.h"
+#include "otg.h"
+
+#include <linux/ulpi/regs.h>
+#include <linux/ulpi/driver.h>
+#include "debug.h"
+
+/* Print the hardware registers' value for debugging purpose */
+static void print_debug_regs(struct dwc3_otg *otg)
+{
+	u32 gctl = otg_read(otg, DWC3_GCTL);
+	u32 gsts = otg_read(otg, DWC3_GSTS);
+	u32 gdbgltssm = otg_read(otg, DWC3_GDBGLTSSM);
+	u32 gusb2phycfg0 = otg_read(otg, DWC3_GUSB2PHYCFG(0));
+	u32 gusb3pipectl0 = otg_read(otg, DWC3_GUSB3PIPECTL(0));
+	u32 dcfg = otg_read(otg, DWC3_DCFG);
+	u32 dctl = otg_read(otg, DWC3_DCTL);
+	u32 dsts = otg_read(otg, DWC3_DSTS);
+	u32 ocfg = otg_read(otg, OCFG);
+	u32 octl = otg_read(otg, OCTL);
+	u32 oevt = otg_read(otg, OEVT);
+	u32 oevten = otg_read(otg, OEVTEN);
+	u32 osts = otg_read(otg, OSTS);
+
+	otg_info(otg, "gctl = %08x\n", gctl);
+	otg_info(otg, "gsts = %08x\n", gsts);
+	otg_info(otg, "gdbgltssm = %08x\n", gdbgltssm);
+	otg_info(otg, "gusb2phycfg0 = %08x\n", gusb2phycfg0);
+	otg_info(otg, "gusb3pipectl0 = %08x\n", gusb3pipectl0);
+	otg_info(otg, "dcfg = %08x\n", dcfg);
+	otg_info(otg, "dctl = %08x\n", dctl);
+	otg_info(otg, "dsts = %08x\n", dsts);
+	otg_info(otg, "ocfg = %08x\n", ocfg);
+	otg_info(otg, "octl = %08x\n", octl);
+	otg_info(otg, "oevt = %08x\n", oevt);
+	otg_info(otg, "oevten = %08x\n", oevten);
+	otg_info(otg, "osts = %08x\n", osts);
+}
+
+/* Check whether the hardware supports HNP or not */
+static int hnp_capable(struct dwc3_otg *otg)
+{
+	if (otg->hwparams6 & GHWPARAMS6_HNP_SUPPORT_ENABLED)
+		return 1;
+	return 0;
+}
+
+/* Check whether the hardware supports SRP or not */
+static int srp_capable(struct dwc3_otg *otg)
+{
+	if (otg->hwparams6 & GHWPARAMS6_SRP_SUPPORT_ENABLED)
+		return 1;
+	return 0;
+}
+
+/* Wakeup main thread to execute the OTG flow after an event */
+static void wakeup_main_thread(struct dwc3_otg *otg)
+{
+	if (!otg->main_thread)
+		return;
+
+	otg_vdbg(otg, "\n");
+	/* Tell the main thread that something has happened */
+	otg->main_wakeup_needed = 1;
+	wake_up_interruptible(&otg->main_wq);
+}
+
+/* Sleep main thread for 'msecs' to wait for an event to occur */
+static int sleep_main_thread_timeout(struct dwc3_otg *otg, int msecs)
+{
+	signed long jiffies;
+	int rc = msecs;
+
+	if (signal_pending(current)) {
+		otg_dbg(otg, "Main thread signal pending\n");
+		rc = -EINTR;
+		goto done;
+	}
+	if (otg->main_wakeup_needed) {
+		otg_dbg(otg, "Main thread wakeup needed\n");
+		rc = msecs;
+		goto done;
+	}
+
+	jiffies = msecs_to_jiffies(msecs);
+	rc = wait_event_freezable_timeout(otg->main_wq,
+					  otg->main_wakeup_needed,
+					  jiffies);
+
+	if (rc > 0)
+		rc = jiffies_to_msecs(rc);
+
+done:
+	otg->main_wakeup_needed = 0;
+	return rc;
+}
+
+/* Sleep main thread to wait for an event to occur */
+static int sleep_main_thread(struct dwc3_otg *otg)
+{
+	int rc;
+
+	do {
+		rc = sleep_main_thread_timeout(otg, 5000);
+	} while (rc == 0);
+
+	return rc;
+}
+
+static void get_events(struct dwc3_otg *otg, u32 *otg_events, u32 *user_events)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&otg->lock, flags);
+
+	if (otg_events)
+		*otg_events = otg->otg_events;
+
+	if (user_events)
+		*user_events = otg->user_events;
+
+	spin_unlock_irqrestore(&otg->lock, flags);
+}
+
+static void get_and_clear_events(struct dwc3_otg *otg, u32 *otg_events,
+		u32 *user_events)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&otg->lock, flags);
+
+	if (otg_events)
+		*otg_events = otg->otg_events;
+
+	if (user_events)
+		*user_events = otg->user_events;
+
+	otg->otg_events = 0;
+	otg->user_events = 0;
+
+	spin_unlock_irqrestore(&otg->lock, flags);
+}
+
+static int check_event(struct dwc3_otg *otg, u32 otg_mask, u32 user_mask)
+{
+	u32 otg_events;
+	u32 user_events;
+
+	get_events(otg, &otg_events, &user_events);
+	if ((otg_events & otg_mask) || (user_events & user_mask)) {
+		otg_dbg(otg, "Event occurred: otg_events=%x, otg_mask=%x, \
+				user_events=%x, user_mask=%x\n", otg_events,
+				otg_mask, user_events, user_mask);
+		return 1;
+	}
+
+	return 0;
+}
+
+static int sleep_until_event(struct dwc3_otg *otg, u32 otg_mask, u32 user_mask,
+		u32 *otg_events, u32 *user_events, int timeout)
+{
+	int rc;
+
+	/* Enable the events */
+	if (otg_mask)
+		otg_write(otg, OEVTEN, otg_mask);
+
+	/* Wait until it occurs, or timeout, or interrupt. */
+	if (timeout) {
+		otg_vdbg(otg, "Waiting for event (timeout=%d)...\n", timeout);
+		rc = sleep_main_thread_until_condition_timeout(otg,
+			check_event(otg, otg_mask, user_mask), timeout);
+	} else {
+		otg_vdbg(otg, "Waiting for event (no timeout)...\n");
+		rc = sleep_main_thread_until_condition(otg,
+			check_event(otg, otg_mask, user_mask));
+	}
+
+	/* Disable the events */
+	otg_write(otg, OEVTEN, 0);
+
+	otg_vdbg(otg, "Woke up rc=%d\n", rc);
+	if (rc >= 0)
+		get_and_clear_events(otg, otg_events, user_events);
+
+	return rc;
+}
+
+static void set_capabilities(struct dwc3_otg *otg)
+{
+	u32 ocfg = 0;
+
+	otg_dbg(otg, "\n");
+	if (srp_capable(otg))
+		ocfg |= OCFG_SRP_CAP;
+
+	if (hnp_capable(otg))
+		ocfg |= OCFG_HNP_CAP;
+
+	otg_write(otg, OCFG, ocfg);
+
+	otg_dbg(otg, "Enabled SRP and HNP capabilities in OCFG\n");
+}
+
+static int otg3_handshake(struct dwc3_otg *otg, u32 reg, u32 mask, u32 done,
+		u32 msec)
+{
+	u32 result;
+	u32 usec = msec * 1000;
+
+	otg_vdbg(otg, "reg=%08x, mask=%08x, value=%08x\n", reg, mask, done);
+	do {
+		result = otg_read(otg, reg);
+		if ((result & mask) == done)
+			return 1;
+		udelay(1);
+		usec -= 1;
+	} while (usec > 0);
+
+	return 0;
+}
+
+static int reset_port(struct dwc3_otg *otg)
+{
+	otg_dbg(otg, "\n");
+	if (!otg->otg.host)
+		return -ENODEV;
+	return usb_bus_start_enum(otg->otg.host, 1);
+}
+
+static int set_peri_mode(struct dwc3_otg *otg, int mode)
+{
+	u32 octl;
+
+	/* Set peri_mode */
+	octl = otg_read(otg, OCTL);
+	if (mode)
+		octl |= OCTL_PERI_MODE;
+	else
+		octl &= ~OCTL_PERI_MODE;
+
+	otg_write(otg, OCTL, octl);
+	otg_dbg(otg, "set OCTL PERI_MODE = %d in OCTL\n", mode);
+
+	if (mode)
+		return otg3_handshake(otg, OSTS, OSTS_PERIP_MODE,
+				OSTS_PERIP_MODE, 100);
+	else
+		return otg3_handshake(otg, OSTS, OSTS_PERIP_MODE, 0, 100);
+
+	msleep(20);
+}
+
+static int start_host(struct dwc3_otg *otg)
+{
+	int ret = -ENODEV;
+	int flg;
+	u32 octl;
+	u32 osts;
+	u32 ocfg;
+	u32 dctl;
+	struct usb_hcd *hcd;
+	struct xhci_hcd *xhci;
+
+	otg_dbg(otg, "\n");
+
+	if (!otg->otg.host)
+		return -ENODEV;
+
+	/*
+	 * Prevent the host USBCMD.HCRST from resetting OTG core by setting
+	 * OCFG.OTGSftRstMsk
+	 */
+	ocfg = otg_read(otg, OCFG);
+	ocfg |= DWC3_OCFG_SFTRSTMASK;
+	otg_write(otg, OCFG, ocfg);
+
+	dctl = otg_read(otg, DCTL);
+	if (dctl & DWC3_DCTL_RUN_STOP) {
+		otg_dbg(otg, "Disabling the RUN/STOP bit\n");
+		dctl &= ~DWC3_DCTL_RUN_STOP;
+		otg_write(otg, DCTL, dctl);
+	}
+
+	if (!set_peri_mode(otg, PERI_MODE_HOST)) {
+		otg_err(otg, "Failed to start host\n");
+		return -EINVAL;
+	}
+
+	hcd = container_of(otg->otg.host, struct usb_hcd, self);
+	xhci = hcd_to_xhci(hcd);
+	otg_dbg(otg, "hcd=%p xhci=%p\n", hcd, xhci);
+
+	if (otg->host_started) {
+		otg_info(otg, "Host already started\n");
+		goto skip;
+	}
+
+	/* Start host driver */
+
+	*(struct xhci_hcd **)hcd->hcd_priv = xhci;
+	ret = usb_add_hcd(hcd, otg->hcd_irq, IRQF_SHARED);
+	if (ret) {
+		otg_err(otg, "%s: failed to start primary hcd, ret=%d\n",
+			__func__, ret);
+		return ret;
+	}
+
+	*(struct xhci_hcd **)xhci->shared_hcd->hcd_priv = xhci;
+	if (xhci->shared_hcd) {
+		ret = usb_add_hcd(xhci->shared_hcd, otg->hcd_irq, IRQF_SHARED);
+		if (ret) {
+			otg_err(otg,
+				"%s: failed to start secondary hcd, ret=%d\n",
+				__func__, ret);
+			usb_remove_hcd(hcd);
+			return ret;
+		}
+	}
+
+	otg->host_started = 1;
+skip:
+	hcd->self.otg_port = 1;
+	if (xhci->shared_hcd)
+		xhci->shared_hcd->self.otg_port = 1;
+
+	set_capabilities(otg);
+
+	/* Power the port only for A-host */
+	if (otg->otg.state == OTG_STATE_A_WAIT_VRISE) {
+		/* Spin on xhciPrtPwr bit until it becomes 1 */
+		osts = otg_read(otg, OSTS);
+		flg = otg3_handshake(otg, OSTS,
+				OSTS_XHCI_PRT_PWR,
+				OSTS_XHCI_PRT_PWR,
+				1000);
+		if (flg) {
+			otg_dbg(otg, "Port is powered by xhci-hcd\n");
+			/* Set port power control bit */
+			octl = otg_read(otg, OCTL);
+			octl |= OCTL_PRT_PWR_CTL;
+			otg_write(otg, OCTL, octl);
+		} else {
+			otg_dbg(otg, "Port is not powered by xhci-hcd\n");
+		}
+	}
+
+	return ret;
+}
+
+static int stop_host(struct dwc3_otg *otg)
+{
+	struct usb_hcd *hcd;
+	struct xhci_hcd *xhci;
+
+	otg_dbg(otg, "\n");
+
+	if (!otg->host_started) {
+		otg_info(otg, "Host already stopped\n");
+		return 1;
+	}
+
+	if (!otg->otg.host)
+		return -ENODEV;
+
+	otg_dbg(otg, "%s: turn off host %s\n",
+		__func__, otg->otg.host->bus_name);
+
+	if (work_pending(&otg->hp_work.work)) {
+		while (!cancel_delayed_work(&otg->hp_work))
+			msleep(20);
+	}
+
+	hcd = container_of(otg->otg.host, struct usb_hcd, self);
+	xhci = hcd_to_xhci(hcd);
+
+	if (xhci->shared_hcd)
+		usb_remove_hcd(xhci->shared_hcd);
+	usb_remove_hcd(hcd);
+
+	otg->host_started = 0;
+	otg->dev_enum = 0;
+	return 0;
+}
+
+int dwc3_otg_host_release(struct usb_hcd *hcd)
+{
+	struct usb_bus *bus;
+	struct usb_device *rh;
+	struct usb_device *udev;
+
+	if (!hcd)
+		return -EINVAL;
+
+	bus = &hcd->self;
+	if (!bus->otg_port)
+		return 0;
+
+	rh = bus->root_hub;
+	udev = usb_hub_find_child(rh, bus->otg_port);
+	if (!udev)
+		return 0;
+
+	if (udev->config && udev->parent == udev->bus->root_hub) {
+		struct usb_otg20_descriptor *desc;
+
+		if (__usb_get_extra_descriptor(udev->rawdescriptors[0],
+				le16_to_cpu(udev->config[0].desc.wTotalLength),
+				USB_DT_OTG, (void **)&desc, sizeof(*desc)) ==
+				0) {
+			int err;
+
+			dev_info(&udev->dev, "found OTG descriptor\n");
+			if ((desc->bcdOTG >= 0x0200) &&
+			    (udev->speed == USB_SPEED_HIGH)) {
+				err = usb_control_msg(udev,
+						usb_sndctrlpipe(udev, 0),
+						USB_REQ_SET_FEATURE, 0,
+						USB_DEVICE_TEST_MODE,
+						7 << 8,
+						NULL, 0, USB_CTRL_SET_TIMEOUT);
+				if (err < 0) {
+					dev_info(&udev->dev,
+						"can't initiate HNP from host: %d\n",
+						err);
+					return -1;
+				}
+			}
+		} else {
+			dev_info(&udev->dev, "didn't find OTG descriptor\n");
+		}
+	} else {
+		dev_info(&udev->dev,
+			 "udev->config NULL or udev->parent != udev->bus->root_hub\n");
+	}
+
+	return 0;
+}
+
+/* Sends the host release set feature request */
+static void host_release(struct dwc3_otg *otg)
+{
+	struct usb_hcd *hcd;
+	struct xhci_hcd *xhci;
+
+	otg_dbg(otg, "\n");
+	if (!otg->otg.host)
+		return;
+	hcd = container_of(otg->otg.host, struct usb_hcd, self);
+	xhci = hcd_to_xhci(hcd);
+	dwc3_otg_host_release(hcd);
+	if (xhci->shared_hcd)
+		dwc3_otg_host_release(xhci->shared_hcd);
+}
+
+static void dwc3_otg_setup_event_buffers(struct dwc3_otg *otg)
+{
+	if (dwc3_readl(otg->dwc->regs, DWC3_GEVNTADRLO(0)) == 0x0) {
+
+		otg_dbg(otg, "setting up event buffers\n");
+		dwc3_event_buffers_setup(otg->dwc);
+	}
+
+}
+
+static void start_peripheral(struct dwc3_otg *otg)
+{
+	struct usb_gadget *gadget = otg->otg.gadget;
+	struct dwc3 *dwc = otg->dwc;
+	u32 ocfg;
+
+	otg_dbg(otg, "\n");
+	if (!gadget)
+		return;
+
+	/*
+	 * Prevent the gadget DCTL.CSFTRST from resetting OTG core by setting
+	 * OCFG.OTGSftRstMsk
+	 */
+	ocfg = otg_read(otg, OCFG);
+	ocfg |= DWC3_OCFG_SFTRSTMASK;
+	otg_write(otg, OCFG, ocfg);
+
+	if (!set_peri_mode(otg, PERI_MODE_PERIPHERAL))
+		otg_err(otg, "Failed to set peripheral mode\n");
+
+	if (otg->peripheral_started) {
+		otg_info(otg, "Peripheral already started\n");
+		return;
+	}
+
+	set_capabilities(otg);
+
+	dwc3_otg_setup_event_buffers(otg);
+
+	if (dwc->gadget_driver) {
+		struct dwc3_ep		*dep;
+		int			ret;
+
+		spin_lock(&otg->lock);
+		dep = dwc->eps[0];
+
+		ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_INIT);
+		if (ret)
+			goto err0;
+
+		dep = dwc->eps[1];
+
+		ret = __dwc3_gadget_ep_enable(dep, DWC3_DEPCFG_ACTION_INIT);
+		if (ret)
+			goto err1;
+
+		otg_dbg(otg, "enabled ep in gadget driver\n");
+		/* begin to receive SETUP packets */
+		dwc->ep0state = EP0_SETUP_PHASE;
+		dwc3_ep0_out_start(dwc);
+
+		otg_dbg(otg, "enabled irq\n");
+		dwc3_gadget_enable_irq(dwc);
+
+		otg_write(otg, DCTL, otg_read(otg, DCTL) | DCTL_RUN_STOP);
+		otg_dbg(otg, "Setting DCTL_RUN_STOP to 1 in DCTL\n");
+		spin_unlock(&otg->lock);
+	}
+
+	gadget->b_hnp_enable = 0;
+	gadget->host_request_flag = 0;
+
+	otg->peripheral_started = 1;
+
+	/*
+	 * During HNP the bus shouldn't be idle for more than 155 ms, so
+	 * give enough time for the host to load the stack before start
+	 * triggerring events
+	 */
+	msleep(500);
+
+	return;
+err1:
+		__dwc3_gadget_ep_disable(dwc->eps[0]);
+
+err0:
+		return;
+}
+
+static void stop_peripheral(struct dwc3_otg *otg)
+{
+	struct usb_gadget *gadget = otg->otg.gadget;
+	struct dwc3 *dwc = otg->dwc;
+
+	otg_dbg(otg, "\n");
+
+	if (!otg->peripheral_started) {
+		otg_info(otg, "Peripheral already stopped\n");
+		return;
+	}
+
+	if (!gadget)
+		return;
+
+	otg_dbg(otg, "disabled ep in gadget driver\n");
+	spin_lock(&otg->lock);
+
+	dwc3_gadget_disable_irq(dwc);
+	__dwc3_gadget_ep_disable(dwc->eps[0]);
+	__dwc3_gadget_ep_disable(dwc->eps[1]);
+
+	spin_unlock(&otg->lock);
+
+	otg->peripheral_started = 0;
+	msleep(20);
+}
+
+static void set_b_host(struct dwc3_otg *otg, int val)
+{
+	otg->otg.host->is_b_host = val;
+}
+
+static enum usb_otg_state do_b_idle(struct dwc3_otg *otg);
+
+static int init_b_device(struct dwc3_otg *otg)
+{
+	otg_dbg(otg, "\n");
+	set_capabilities(otg);
+
+	if (!set_peri_mode(otg, PERI_MODE_PERIPHERAL))
+		otg_err(otg, "Failed to start peripheral\n");
+
+	return do_b_idle(otg);
+}
+
+static int init_a_device(struct dwc3_otg *otg)
+{
+	otg_write(otg, OCFG, 0);
+	otg_write(otg, OCTL, 0);
+
+	otg_dbg(otg, "Write 0 to OCFG and OCTL\n");
+	return OTG_STATE_A_IDLE;
+}
+
+static enum usb_otg_state do_connector_id_status(struct dwc3_otg *otg)
+{
+	enum usb_otg_state state;
+	u32 osts;
+
+	otg_dbg(otg, "\n");
+
+	otg_write(otg, OCFG, 0);
+	otg_write(otg, OEVTEN, 0);
+	otg_write(otg, OEVT, 0xffffffff);
+	otg_write(otg, OEVTEN, OEVT_CONN_ID_STS_CHNG_EVNT);
+
+	msleep(60);
+
+	osts = otg_read(otg, OSTS);
+	if (!(osts & OSTS_CONN_ID_STS)) {
+		otg_dbg(otg, "Connector ID is A\n");
+		state = init_a_device(otg);
+	} else {
+		otg_dbg(otg, "Connector ID is B\n");
+		stop_host(otg);
+		state = init_b_device(otg);
+	}
+
+	/* TODO: This is a workaround for latest hibernation-enabled bitfiles
+	 * which have problems before initializing SRP.
+	 */
+	msleep(50);
+
+	return state;
+}
+
+static void reset_hw(struct dwc3_otg *otg)
+{
+	u32 temp;
+
+	otg_dbg(otg, "\n");
+
+	otg_write(otg, OEVTEN, 0);
+	temp = otg_read(otg, OCTL);
+	temp &= OCTL_PERI_MODE;
+	otg_write(otg, OCTL, temp);
+	temp = otg_read(otg, GCTL);
+	temp |= GCTL_PRT_CAP_DIR_OTG << GCTL_PRT_CAP_DIR_SHIFT;
+	otg_write(otg, GCTL, temp);
+}
+
+#define SRP_TIMEOUT			6000
+
+static void start_srp(struct dwc3_otg *otg)
+{
+	u32 octl;
+
+	octl = otg_read(otg, OCTL);
+	octl |= OCTL_SES_REQ;
+	otg_write(otg, OCTL, octl);
+	otg_dbg(otg, "set OCTL_SES_REQ in OCTL\n");
+}
+
+static void start_b_hnp(struct dwc3_otg *otg)
+{
+	u32 octl;
+
+	octl = otg_read(otg, OCTL);
+	octl |= OCTL_HNP_REQ | OCTL_DEV_SET_HNP_EN;
+	otg_write(otg, OCTL, octl);
+	otg_dbg(otg, "set (OCTL_HNP_REQ | OCTL_DEV_SET_HNP_EN) in OCTL\n");
+}
+
+static void stop_b_hnp(struct dwc3_otg *otg)
+{
+	u32 octl;
+
+	octl = otg_read(otg, OCTL);
+	octl &= ~(OCTL_HNP_REQ | OCTL_DEV_SET_HNP_EN);
+	otg_write(otg, OCTL, octl);
+	otg_dbg(otg, "Clear ~(OCTL_HNP_REQ | OCTL_DEV_SET_HNP_EN) in OCTL\n");
+}
+
+static void start_a_hnp(struct dwc3_otg *otg)
+{
+	u32 octl;
+
+	octl = otg_read(otg, OCTL);
+	octl |= OCTL_HST_SET_HNP_EN;
+	otg_write(otg, OCTL, octl);
+	otg_dbg(otg, "set OCTL_HST_SET_HNP_EN in OCTL\n");
+}
+
+static void stop_a_hnp(struct dwc3_otg *otg)
+{
+	u32 octl;
+
+	octl = otg_read(otg, OCTL);
+	octl &= ~OCTL_HST_SET_HNP_EN;
+	otg_write(otg, OCTL, octl);
+	otg_dbg(otg, "clear OCTL_HST_SET_HNP_EN in OCTL\n");
+}
+
+static enum usb_otg_state do_a_hnp_init(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 otg_events = 0;
+
+	otg_dbg(otg, "");
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_A_DEV_HNP_CHNG_EVNT;
+
+	start_a_hnp(otg);
+	rc = 3000;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, 0,
+			&otg_events, NULL, rc);
+	stop_a_hnp(otg);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	/* Higher priority first */
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+
+	} else if (otg_events & OEVT_A_DEV_HNP_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_HNP_CHNG_EVNT\n");
+		if (otg_events & OEVT_HST_NEG_SCS) {
+			otg_dbg(otg, "A-HNP Success\n");
+			return OTG_STATE_A_PERIPHERAL;
+
+		} else {
+			otg_dbg(otg, "A-HNP Failed\n");
+			return OTG_STATE_A_WAIT_VFALL;
+		}
+
+	} else if (rc == 0) {
+		otg_dbg(otg, "A-HNP Failed (Timed out)\n");
+		return OTG_STATE_A_WAIT_VFALL;
+
+	} else {
+		goto again;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_a_host(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+
+	otg_dbg(otg, "");
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_A_DEV_SESS_END_DET_EVNT;
+	user_mask = USER_SRP_EVENT |
+		USER_HNP_EVENT;
+
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events, 0);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	/* Higher priority first */
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+
+	} else if (otg_events & OEVT_A_DEV_SESS_END_DET_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_SESS_END_DET_EVNT\n");
+		return OTG_STATE_A_WAIT_VFALL;
+
+	} else if (user_events & USER_HNP_EVENT) {
+		otg_dbg(otg, "USER_HNP_EVENT\n");
+		return OTG_STATE_A_SUSPEND;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+}
+
+#define A_WAIT_VFALL_TIMEOUT 1000
+
+static enum usb_otg_state do_a_wait_vfall(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 otg_events = 0;
+
+	otg_dbg(otg, "");
+
+	otg_mask = OEVT_A_DEV_IDLE_EVNT;
+
+	rc = A_WAIT_VFALL_TIMEOUT;
+	rc = sleep_until_event(otg,
+			otg_mask, 0,
+			&otg_events, NULL, rc);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (otg_events & OEVT_A_DEV_IDLE_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_IDLE_EVNT\n");
+		return OTG_STATE_A_IDLE;
+
+	} else if (rc == 0) {
+		otg_dbg(otg, "A_WAIT_VFALL_TIMEOUT\n");
+		return OTG_STATE_A_IDLE;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+
+}
+
+#define A_WAIT_BCON_TIMEOUT 1000
+
+static enum usb_otg_state do_a_wait_bconn(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 otg_events = 0;
+
+	otg_dbg(otg, "");
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_A_DEV_SESS_END_DET_EVNT |
+		OEVT_A_DEV_HOST_EVNT;
+
+	rc = A_WAIT_BCON_TIMEOUT;
+	rc = sleep_until_event(otg,
+			otg_mask, 0,
+			&otg_events, NULL, rc);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	/* Higher priority first */
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+
+	} else if (otg_events & OEVT_A_DEV_SESS_END_DET_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_SESS_END_DET_EVNT\n");
+		return OTG_STATE_A_WAIT_VFALL;
+
+	} else if (otg_events & OEVT_A_DEV_HOST_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_HOST_EVNT\n");
+		return OTG_STATE_A_HOST;
+
+	} else if (rc == 0) {
+		if (otg_read(otg, OCTL) & OCTL_PRT_PWR_CTL)
+			return OTG_STATE_A_HOST;
+		else
+			return OTG_STATE_A_WAIT_VFALL;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+}
+
+#define A_WAIT_VRISE_TIMEOUT 100
+
+static enum usb_otg_state do_a_wait_vrise(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 otg_events = 0;
+	struct usb_hcd *hcd;
+	struct xhci_hcd *xhci;
+
+	otg_dbg(otg, "");
+	set_b_host(otg, 0);
+	start_host(otg);
+	hcd = container_of(otg->otg.host, struct usb_hcd, self);
+	xhci = hcd_to_xhci(hcd);
+	usb_kick_hub_wq(hcd->self.root_hub);
+	if (xhci->shared_hcd)
+		usb_kick_hub_wq(xhci->shared_hcd->self.root_hub);
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_A_DEV_SESS_END_DET_EVNT;
+
+	rc = A_WAIT_VRISE_TIMEOUT;
+
+	rc = sleep_until_event(otg,
+			otg_mask, 0,
+			&otg_events, NULL, rc);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	/* Higher priority first */
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+
+	} else if (otg_events & OEVT_A_DEV_SESS_END_DET_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_SESS_END_DET_EVNT\n");
+		return OTG_STATE_A_WAIT_VFALL;
+
+	} else if (rc == 0) {
+		if (otg_read(otg, OCTL) & OCTL_PRT_PWR_CTL)
+			return OTG_STATE_A_WAIT_BCON;
+		else
+			return OTG_STATE_A_WAIT_VFALL;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_a_idle(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+
+	otg_dbg(otg, "");
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT | OEVT_A_DEV_SRP_DET_EVNT;
+	user_mask = USER_SRP_EVENT;
+
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events,
+			0);
+
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if (otg_events & OEVT_A_DEV_SRP_DET_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_SRP_DET_EVNT\n");
+		return OTG_STATE_A_WAIT_VRISE;
+	} else if (user_events & USER_SRP_EVENT) {
+		otg_dbg(otg, "User initiated VBUS\n");
+		return OTG_STATE_A_WAIT_VRISE;
+	}
+
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_a_peripheral(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+
+	otg_dbg(otg, "");
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_A_DEV_SESS_END_DET_EVNT |
+		OEVT_A_DEV_B_DEV_HOST_END_EVNT;
+	user_mask = USER_HNP_END_SESSION;
+
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events, 0);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+
+	} else if (otg_events & OEVT_A_DEV_SESS_END_DET_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_SESS_END_DET_EVNT\n");
+		return OTG_STATE_A_WAIT_VFALL;
+
+	} else if (otg_events & OEVT_A_DEV_B_DEV_HOST_END_EVNT) {
+		otg_dbg(otg, "OEVT_A_DEV_B_DEV_HOST_END_EVNT\n");
+		return OTG_STATE_A_WAIT_VRISE;
+	} else if (user_events & USER_HNP_END_SESSION) {
+		otg_dbg(otg, "USER_HNP_END_SESSION\n");
+		return OTG_STATE_A_WAIT_VRISE;
+	}
+
+	return OTG_STATE_UNDEFINED;
+}
+
+#define HNP_TIMEOUT	4000
+
+static enum usb_otg_state do_b_hnp_init(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 events = 0;
+
+	otg_dbg(otg, "");
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_B_DEV_HNP_CHNG_EVNT |
+		OEVT_B_DEV_VBUS_CHNG_EVNT;
+
+	start_b_hnp(otg);
+	rc = HNP_TIMEOUT;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, 0,
+			&events, NULL, rc);
+	stop_b_hnp(otg);
+
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if (events & OEVT_B_DEV_VBUS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_VBUS_CHNG_EVNT\n");
+		return OTG_STATE_B_IDLE;
+	} else if (events & OEVT_B_DEV_HNP_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_HNP_CHNG_EVNT\n");
+		if (events & OEVT_HST_NEG_SCS) {
+			otg_dbg(otg, "B-HNP Success\n");
+			return OTG_STATE_B_WAIT_ACON;
+
+		} else {
+			otg_err(otg, "B-HNP Failed\n");
+			return OTG_STATE_B_PERIPHERAL;
+		}
+	} else if (rc == 0) {
+		/* Timeout */
+		otg_err(otg, "HNP timed out!\n");
+		return OTG_STATE_B_PERIPHERAL;
+
+	} else {
+		goto again;
+	}
+
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_b_peripheral(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+
+	otg_dbg(otg, "");
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT | OEVT_B_DEV_VBUS_CHNG_EVNT;
+	user_mask = USER_HNP_EVENT | USER_END_SESSION |
+		USER_SRP_EVENT | INITIAL_SRP;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events, 0);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if (otg_events & OEVT_B_DEV_VBUS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_VBUS_CHNG_EVNT\n");
+
+		if (otg_events & OEVT_B_SES_VLD_EVT) {
+			otg_dbg(otg, "Session valid\n");
+			goto again;
+		} else {
+			otg_dbg(otg, "Session not valid\n");
+			return OTG_STATE_B_IDLE;
+		}
+
+	} else if (user_events & USER_HNP_EVENT) {
+		otg_dbg(otg, "USER_HNP_EVENT\n");
+		return do_b_hnp_init(otg);
+	} else if (user_events & USER_END_SESSION) {
+		otg_dbg(otg, "USER_END_SESSION\n");
+		return OTG_STATE_B_IDLE;
+	}
+
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_b_wait_acon(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask = 0;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+	struct usb_hcd *hcd;
+	struct xhci_hcd *xhci;
+
+	otg_dbg(otg, "");
+	set_b_host(otg, 1);
+	start_host(otg);
+	otg_mask = OEVT_B_DEV_B_HOST_END_EVNT;
+	otg_write(otg, OEVTEN, otg_mask);
+	reset_port(otg);
+
+	hcd = container_of(otg->otg.host, struct usb_hcd, self);
+	xhci = hcd_to_xhci(hcd);
+	usb_kick_hub_wq(hcd->self.root_hub);
+	if (xhci->shared_hcd)
+		usb_kick_hub_wq(xhci->shared_hcd->self.root_hub);
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_B_DEV_B_HOST_END_EVNT |
+		OEVT_B_DEV_VBUS_CHNG_EVNT |
+		OEVT_HOST_ROLE_REQ_INIT_EVNT;
+	user_mask = USER_A_CONN_EVENT | USER_HNP_END_SESSION;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events, 0);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	/* Higher priority first */
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if (otg_events & OEVT_B_DEV_B_HOST_END_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_B_HOST_END_EVNT\n");
+		return OTG_STATE_B_PERIPHERAL;
+	} else if (otg_events & OEVT_B_DEV_VBUS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_VBUS_CHNG_EVNT\n");
+		if (otg_events & OEVT_B_SES_VLD_EVT) {
+			otg_dbg(otg, "Session valid\n");
+			goto again;
+		} else {
+			otg_dbg(otg, "Session not valid\n");
+			return OTG_STATE_B_IDLE;
+		}
+	} else if (user_events & USER_A_CONN_EVENT) {
+		otg_dbg(otg, "A-device connected\n");
+		return OTG_STATE_B_HOST;
+	} else if (user_events & USER_HNP_END_SESSION) {
+		otg_dbg(otg, "USER_HNP_END_SESSION\n");
+		return OTG_STATE_B_PERIPHERAL;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_b_host(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask = 0;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+
+	otg_dbg(otg, "");
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_B_DEV_B_HOST_END_EVNT |
+		OEVT_B_DEV_VBUS_CHNG_EVNT |
+		OEVT_HOST_ROLE_REQ_INIT_EVNT;
+	user_mask = USER_HNP_END_SESSION;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events, 0);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	/* Higher priority first */
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if (otg_events & OEVT_B_DEV_B_HOST_END_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_B_HOST_END_EVNT\n");
+		return OTG_STATE_B_PERIPHERAL;
+	} else if (otg_events & OEVT_B_DEV_VBUS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_VBUS_CHNG_EVNT\n");
+		if (otg_events & OEVT_B_SES_VLD_EVT) {
+			otg_dbg(otg, "Session valid\n");
+			goto again;
+		} else {
+			otg_dbg(otg, "Session not valid\n");
+			return OTG_STATE_B_IDLE;
+		}
+	} else if (user_events & USER_HNP_END_SESSION) {
+		otg_dbg(otg, "USER_HNP_END_SESSION\n");
+		return OTG_STATE_B_PERIPHERAL;
+	}
+
+	/* Invalid state */
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_b_idle(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 user_mask;
+	u32 otg_events = 0;
+	u32 user_events = 0;
+
+	otg_dbg(otg, "");
+
+	if (!set_peri_mode(otg, PERI_MODE_PERIPHERAL))
+		otg_err(otg, "Failed to set peripheral mode\n");
+
+	dwc3_otg_setup_event_buffers(otg);
+
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_B_DEV_SES_VLD_DET_EVNT |
+		OEVT_B_DEV_VBUS_CHNG_EVNT;
+	user_mask = USER_SRP_EVENT;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, user_mask,
+			&otg_events, &user_events, 0);
+
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (otg_events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if ((otg_events & OEVT_B_DEV_VBUS_CHNG_EVNT) ||
+		(otg_events & OEVT_B_DEV_SES_VLD_DET_EVNT)) {
+		otg_dbg(otg, "OEVT_B_DEV_VBUS_CHNG_EVNT\n");
+		if (otg_events & OEVT_B_SES_VLD_EVT) {
+			otg_dbg(otg, "Session valid\n");
+			return OTG_STATE_B_PERIPHERAL;
+
+		} else {
+			otg_dbg(otg, "Session not valid\n");
+			goto again;
+		}
+	} else if (user_events & USER_SRP_EVENT) {
+		otg_dbg(otg, "USER_SRP_EVENT\n");
+		return OTG_STATE_B_SRP_INIT;
+	}
+
+	return OTG_STATE_UNDEFINED;
+}
+
+static enum usb_otg_state do_b_srp_init(struct dwc3_otg *otg)
+{
+	int rc;
+	u32 otg_mask;
+	u32 events = 0;
+
+	otg_dbg(otg, "");
+	otg_mask = OEVT_CONN_ID_STS_CHNG_EVNT |
+		OEVT_B_DEV_SES_VLD_DET_EVNT |
+		OEVT_B_DEV_VBUS_CHNG_EVNT;
+
+	otg_write(otg, OEVTEN, otg_mask);
+	start_srp(otg);
+
+	rc = SRP_TIMEOUT;
+
+again:
+	rc = sleep_until_event(otg,
+			otg_mask, 0,
+			&events, NULL, rc);
+	if (rc < 0)
+		return OTG_STATE_UNDEFINED;
+
+	if (events & OEVT_CONN_ID_STS_CHNG_EVNT) {
+		otg_dbg(otg, "OEVT_CONN_ID_STS_CHNG_EVNT\n");
+		return OTG_STATE_UNDEFINED;
+	} else if (events & OEVT_B_DEV_SES_VLD_DET_EVNT) {
+		otg_dbg(otg, "OEVT_B_DEV_SES_VLD_DET_EVNT\n");
+		return OTG_STATE_B_PERIPHERAL;
+	} else if (rc == 0) {
+		otg_dbg(otg, "SRP Timeout (rc=%d)\n", rc);
+		otg_info(otg, "DEVICE NO RESPONSE FOR SRP\n");
+		return OTG_STATE_B_IDLE;
+
+	} else {
+		goto again;
+	}
+
+	return OTG_STATE_UNDEFINED;
+}
+
+int otg_main_thread(void *data)
+{
+	struct dwc3_otg *otg = (struct dwc3_otg *)data;
+	enum usb_otg_state prev = OTG_STATE_UNDEFINED;
+
+#ifdef VERBOSE_DEBUG
+	u32 snpsid = otg_read(otg, 0xc120);
+
+	otg_vdbg(otg, "io_priv=%p\n", otg->regs);
+	otg_vdbg(otg, "c120: %x\n", snpsid);
+#endif
+
+	/* Allow the thread to be killed by a signal, but set the signal mask
+	 * to block everything but INT, TERM, KILL, and USR1.
+	 */
+	allow_signal(SIGINT);
+	allow_signal(SIGTERM);
+	allow_signal(SIGKILL);
+	allow_signal(SIGUSR1);
+
+	/* Allow the thread to be frozen */
+	set_freezable();
+
+	/* Allow host/peripheral driver load to finish */
+	msleep(100);
+
+	reset_hw(otg);
+
+	stop_host(otg);
+	stop_peripheral(otg);
+
+	otg_dbg(otg, "Thread running\n");
+	while (1) {
+		enum usb_otg_state next = OTG_STATE_UNDEFINED;
+
+		otg_vdbg(otg, "Main thread entering state\n");
+
+		switch (otg->otg.state) {
+		case OTG_STATE_UNDEFINED:
+			otg_dbg(otg, "OTG_STATE_UNDEFINED\n");
+			next = do_connector_id_status(otg);
+			break;
+
+		case OTG_STATE_A_IDLE:
+			otg_dbg(otg, "OTG_STATE_A_IDLE\n");
+			stop_peripheral(otg);
+
+			if (prev == OTG_STATE_UNDEFINED)
+				next = OTG_STATE_A_WAIT_VRISE;
+			else
+				next = do_a_idle(otg);
+			break;
+
+		case OTG_STATE_A_WAIT_VRISE:
+			otg_dbg(otg, "OTG_STATE_A_WAIT_VRISE\n");
+			next = do_a_wait_vrise(otg);
+			break;
+
+		case OTG_STATE_A_WAIT_BCON:
+			otg_dbg(otg, "OTG_STATE_A_WAIT_BCON\n");
+			next = do_a_wait_bconn(otg);
+			break;
+
+		case OTG_STATE_A_HOST:
+			otg_dbg(otg, "OTG_STATE_A_HOST\n");
+			stop_peripheral(otg);
+			next = do_a_host(otg);
+			/* Don't stop the host here if we are going into
+			 * A_SUSPEND. We need to delay that until later. It
+			 * will be stopped when coming out of A_SUSPEND
+			 * state.
+			 */
+			if (next != OTG_STATE_A_SUSPEND)
+				stop_host(otg);
+			break;
+
+		case OTG_STATE_A_SUSPEND:
+			otg_dbg(otg, "OTG_STATE_A_SUSPEND\n");
+			next = do_a_hnp_init(otg);
+
+			/* Stop the host. */
+			stop_host(otg);
+			break;
+
+		case OTG_STATE_A_WAIT_VFALL:
+			otg_dbg(otg, "OTG_STATE_A_WAIT_VFALL\n");
+			next = do_a_wait_vfall(otg);
+			stop_host(otg);
+			break;
+
+		case OTG_STATE_A_PERIPHERAL:
+			otg_dbg(otg, "OTG_STATE_A_PERIPHERAL\n");
+			stop_host(otg);
+			start_peripheral(otg);
+			next = do_a_peripheral(otg);
+			stop_peripheral(otg);
+			break;
+
+		case OTG_STATE_B_IDLE:
+			otg_dbg(otg, "OTG_STATE_B_IDLE\n");
+			next = do_b_idle(otg);
+			break;
+
+		case OTG_STATE_B_PERIPHERAL:
+			otg_dbg(otg, "OTG_STATE_B_PERIPHERAL\n");
+			stop_host(otg);
+			start_peripheral(otg);
+			next = do_b_peripheral(otg);
+			stop_peripheral(otg);
+			break;
+
+		case OTG_STATE_B_SRP_INIT:
+			otg_dbg(otg, "OTG_STATE_B_SRP_INIT\n");
+			otg_read(otg, OSTS);
+			next = do_b_srp_init(otg);
+			break;
+
+		case OTG_STATE_B_WAIT_ACON:
+			otg_dbg(otg, "OTG_STATE_B_WAIT_ACON\n");
+			next = do_b_wait_acon(otg);
+			break;
+
+		case OTG_STATE_B_HOST:
+			otg_dbg(otg, "OTG_STATE_B_HOST\n");
+			next = do_b_host(otg);
+			stop_host(otg);
+			break;
+
+		default:
+			otg_err(otg, "Unknown state %d, sleeping...\n",
+					otg->state);
+			sleep_main_thread(otg);
+			break;
+		}
+
+		prev = otg->otg.state;
+		otg->otg.state = next;
+		if (kthread_should_stop())
+			break;
+	}
+
+	otg->main_thread = NULL;
+	otg_dbg(otg, "OTG main thread exiting....\n");
+
+	return 0;
+}
+
+static void start_main_thread(struct dwc3_otg *otg)
+{
+	if (!otg->main_thread && otg->otg.gadget && otg->otg.host) {
+		otg_dbg(otg, "Starting OTG main thread\n");
+		otg->main_thread = kthread_create(otg_main_thread, otg, "otg");
+		wake_up_process(otg->main_thread);
+	}
+}
+
+static inline struct dwc3_otg *otg_to_dwc3_otg(struct usb_otg *x)
+{
+	return container_of(x, struct dwc3_otg, otg);
+}
+
+static irqreturn_t dwc3_otg_irq(int irq, void *_otg)
+{
+	struct dwc3_otg *otg;
+	u32 oevt;
+	u32 osts;
+	u32 octl;
+	u32 ocfg;
+	u32 oevten;
+	u32 otg_mask = OEVT_ALL;
+
+	if (!_otg)
+		return 0;
+
+	otg = (struct dwc3_otg *)_otg;
+
+	oevt = otg_read(otg, OEVT);
+	osts = otg_read(otg, OSTS);
+	octl = otg_read(otg, OCTL);
+	ocfg = otg_read(otg, OCFG);
+	oevten = otg_read(otg, OEVTEN);
+
+	/* Clear handled events */
+	otg_write(otg, OEVT, oevt);
+
+	otg_vdbg(otg, "\n");
+	otg_vdbg(otg, "    oevt = %08x\n", oevt);
+	otg_vdbg(otg, "    osts = %08x\n", osts);
+	otg_vdbg(otg, "    octl = %08x\n", octl);
+	otg_vdbg(otg, "    ocfg = %08x\n", ocfg);
+	otg_vdbg(otg, "  oevten = %08x\n", oevten);
+
+	otg_vdbg(otg, "oevt[DeviceMode] = %s\n",
+			oevt & OEVT_DEV_MOD_EVNT ? "Device" : "Host");
+
+	if (oevt & OEVT_CONN_ID_STS_CHNG_EVNT)
+		otg_dbg(otg, "Connector ID Status Change Event\n");
+	if (oevt & OEVT_HOST_ROLE_REQ_INIT_EVNT)
+		otg_dbg(otg, "Host Role Request Init Notification Event\n");
+	if (oevt & OEVT_HOST_ROLE_REQ_CONFIRM_EVNT)
+		otg_dbg(otg, "Host Role Request Confirm Notification Event\n");
+	if (oevt & OEVT_A_DEV_B_DEV_HOST_END_EVNT)
+		otg_dbg(otg, "A-Device B-Host End Event\n");
+	if (oevt & OEVT_A_DEV_HOST_EVNT)
+		otg_dbg(otg, "A-Device Host Event\n");
+	if (oevt & OEVT_A_DEV_HNP_CHNG_EVNT)
+		otg_dbg(otg, "A-Device HNP Change Event\n");
+	if (oevt & OEVT_A_DEV_SRP_DET_EVNT)
+		otg_dbg(otg, "A-Device SRP Detect Event\n");
+	if (oevt & OEVT_A_DEV_SESS_END_DET_EVNT)
+		otg_dbg(otg, "A-Device Session End Detected Event\n");
+	if (oevt & OEVT_B_DEV_B_HOST_END_EVNT)
+		otg_dbg(otg, "B-Device B-Host End Event\n");
+	if (oevt & OEVT_B_DEV_HNP_CHNG_EVNT)
+		otg_dbg(otg, "B-Device HNP Change Event\n");
+	if (oevt & OEVT_B_DEV_SES_VLD_DET_EVNT)
+		otg_dbg(otg, "B-Device Session Valid Detect Event\n");
+	if (oevt & OEVT_B_DEV_VBUS_CHNG_EVNT)
+		otg_dbg(otg, "B-Device VBUS Change Event\n");
+
+	if (oevt & otg_mask) {
+		/* Pass event to main thread */
+		spin_lock(&otg->lock);
+		otg->otg_events |= oevt;
+		wakeup_main_thread(otg);
+		spin_unlock(&otg->lock);
+		return 1;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void hnp_polling_work(struct work_struct *w)
+{
+	struct dwc3_otg *otg = container_of(w, struct dwc3_otg,
+			hp_work.work);
+	struct usb_bus *bus;
+	struct usb_device *udev;
+	struct usb_hcd *hcd;
+	u8 *otgstatus;
+	int ret;
+	int err;
+
+	hcd = container_of(otg->otg.host, struct usb_hcd, self);
+	if (!hcd)
+		return;
+
+	bus = &hcd->self;
+	if (!bus->otg_port)
+		return;
+
+	udev = usb_hub_find_child(bus->root_hub, bus->otg_port);
+	if (!udev)
+		return;
+
+	otgstatus = kmalloc(sizeof(*otgstatus), GFP_NOIO);
+	if (!otgstatus)
+		return;
+
+	ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
+			USB_REQ_GET_STATUS, USB_DIR_IN | USB_RECIP_DEVICE,
+			0, 0xf000, otgstatus, sizeof(*otgstatus),
+			USB_CTRL_GET_TIMEOUT);
+
+	if (ret == sizeof(*otgstatus) && (*otgstatus & 0x1)) {
+		/* enable HNP before suspend, it's simpler */
+
+		udev->bus->b_hnp_enable = 1;
+		err = usb_control_msg(udev,
+				usb_sndctrlpipe(udev, 0),
+				USB_REQ_SET_FEATURE, 0,
+				udev->bus->b_hnp_enable
+				? USB_DEVICE_B_HNP_ENABLE
+				: USB_DEVICE_A_ALT_HNP_SUPPORT,
+				0, NULL, 0, USB_CTRL_SET_TIMEOUT);
+
+		if (err < 0) {
+			/* OTG MESSAGE: report errors here,
+			 * customize to match your product.
+			 */
+			otg_info(otg, "ERROR : Device no response\n");
+			dev_info(&udev->dev, "can't set HNP mode: %d\n",
+					err);
+			udev->bus->b_hnp_enable = 0;
+			if (le16_to_cpu(udev->descriptor.idVendor) == 0x1a0a) {
+				if (usb_port_suspend(udev, PMSG_AUTO_SUSPEND)
+						< 0)
+					dev_dbg(&udev->dev, "HNP fail, %d\n",
+							err);
+			}
+		} else {
+			/* Device wants role-switch, suspend the bus. */
+			static struct usb_phy *phy;
+
+			phy = usb_get_phy(USB_PHY_TYPE_USB3);
+			otg_start_hnp(phy->otg);
+			usb_put_phy(phy);
+
+			if (usb_port_suspend(udev, PMSG_AUTO_SUSPEND) < 0)
+				dev_dbg(&udev->dev, "HNP fail, %d\n", err);
+		}
+	} else if (ret < 0) {
+		udev->bus->b_hnp_enable = 1;
+		err = usb_control_msg(udev,
+				usb_sndctrlpipe(udev, 0),
+				USB_REQ_SET_FEATURE, 0,
+				USB_DEVICE_B_HNP_ENABLE,
+				0, NULL, 0, USB_CTRL_SET_TIMEOUT);
+		if (usb_port_suspend(udev, PMSG_AUTO_SUSPEND) < 0)
+			dev_dbg(&udev->dev, "HNP fail, %d\n", err);
+	} else {
+		schedule_delayed_work(&otg->hp_work, 1 * HZ);
+	}
+
+	kfree(otgstatus);
+}
+
+static int dwc3_otg_notify_connect(struct usb_phy *phy,
+		enum usb_device_speed speed)
+{
+	struct usb_bus *bus;
+	struct usb_device *udev;
+	struct usb_hcd *hcd;
+	struct dwc3_otg *otg;
+	int err = 0;
+
+	otg = otg_to_dwc3_otg(phy->otg);
+
+	hcd = container_of(phy->otg->host, struct usb_hcd, self);
+	if (!hcd)
+		return -EINVAL;
+
+	bus = &hcd->self;
+	if (!bus->otg_port)
+		return 0;
+
+	udev = usb_hub_find_child(bus->root_hub, bus->otg_port);
+	if (!udev)
+		return 0;
+
+	/*
+	 * OTG-aware devices on OTG-capable root hubs may be able to use SRP,
+	 * to wake us after we've powered off VBUS; and HNP, switching roles
+	 * "host" to "peripheral".  The OTG descriptor helps figure this out.
+	 */
+	if (udev->config && udev->parent == udev->bus->root_hub) {
+		struct usb_otg20_descriptor	*desc = NULL;
+
+		/* descriptor may appear anywhere in config */
+		err = __usb_get_extra_descriptor(udev->rawdescriptors[0],
+				le16_to_cpu(udev->config[0].desc.wTotalLength),
+				USB_DT_OTG, (void **)&desc, sizeof(*desc));
+		if (err || !(desc->bmAttributes & USB_OTG_HNP))
+			return 0;
+
+		if (udev->portnum == udev->bus->otg_port) {
+			INIT_DELAYED_WORK(&otg->hp_work,
+					hnp_polling_work);
+			schedule_delayed_work(&otg->hp_work, HZ);
+		}
+
+	}
+
+	return err;
+}
+
+static int dwc3_otg_notify_disconnect(struct usb_phy *phy,
+		enum usb_device_speed speed)
+{
+	struct dwc3_otg *otg;
+
+	otg = otg_to_dwc3_otg(phy->otg);
+
+	if (work_pending(&otg->hp_work.work)) {
+		while (!cancel_delayed_work(&otg->hp_work))
+			msleep(20);
+	}
+	return 0;
+}
+
+static void dwc3_otg_set_peripheral(struct usb_otg *_otg, int yes)
+{
+	struct dwc3_otg *otg;
+
+	if (!_otg)
+		return;
+
+	otg = otg_to_dwc3_otg(_otg);
+	otg_dbg(otg, "\n");
+
+	if (yes) {
+		if (otg->hwparams6 == 0xdeadbeef)
+			otg->hwparams6 = otg_read(otg, GHWPARAMS6);
+		stop_host(otg);
+	} else {
+		stop_peripheral(otg);
+	}
+
+	set_peri_mode(otg, yes);
+}
+
+static int dwc3_otg_set_periph(struct usb_otg *_otg, struct usb_gadget *gadget)
+{
+	struct dwc3_otg *otg;
+
+	if (!_otg)
+		return -ENODEV;
+
+	otg = otg_to_dwc3_otg(_otg);
+	otg_dbg(otg, "\n");
+
+	if ((long)gadget == 1) {
+		dwc3_otg_set_peripheral(_otg, 1);
+		return 0;
+	}
+
+	if (!gadget) {
+		otg->otg.gadget = NULL;
+		return -ENODEV;
+	}
+
+	otg->otg.gadget = gadget;
+	otg->otg.gadget->hnp_polling_support = 1;
+	otg->otg.state = OTG_STATE_B_IDLE;
+
+	start_main_thread(otg);
+	return 0;
+}
+
+static int dwc3_otg_set_host(struct usb_otg *_otg, struct usb_bus *host)
+{
+	struct dwc3_otg *otg;
+	struct usb_hcd *hcd;
+	struct xhci_hcd *xhci;
+
+	if (!_otg)
+		return -ENODEV;
+
+	otg = otg_to_dwc3_otg(_otg);
+	otg_dbg(otg, "\n");
+
+	if (host == (struct usb_bus *)0xdeadbeef) {
+		dwc3_otg_set_peripheral(_otg, 0);
+		return 0;
+	}
+
+	if (!host) {
+		otg->otg.host = NULL;
+		otg->hcd_irq = 0;
+		return -ENODEV;
+	}
+
+	hcd = container_of(host, struct usb_hcd, self);
+	xhci = hcd_to_xhci(hcd);
+	otg_dbg(otg, "hcd=%p xhci=%p\n", hcd, xhci);
+
+	hcd->self.otg_port = 1;
+	if (xhci->shared_hcd) {
+		xhci->shared_hcd->self.otg_port = 1;
+		otg_dbg(otg, "shared_hcd=%p\n", xhci->shared_hcd);
+	}
+
+	otg->otg.host = host;
+	otg->hcd_irq = hcd->irq;
+	otg_dbg(otg, "host=%p irq=%d\n", otg->otg.host, otg->hcd_irq);
+
+
+	otg->host_started = 1;
+	otg->dev_enum = 0;
+	start_main_thread(otg);
+	return 0;
+}
+
+static int dwc3_otg_start_srp(struct usb_otg *x)
+{
+	unsigned long flags;
+	struct dwc3_otg *otg;
+
+	if (!x)
+		return -ENODEV;
+
+	otg = otg_to_dwc3_otg(x);
+	otg_dbg(otg, "\n");
+
+	if (!otg->otg.host || !otg->otg.gadget)
+		return -ENODEV;
+
+	spin_lock_irqsave(&otg->lock, flags);
+	otg->user_events |= USER_SRP_EVENT;
+	wakeup_main_thread(otg);
+	spin_unlock_irqrestore(&otg->lock, flags);
+	return 0;
+}
+
+static int dwc3_otg_start_hnp(struct usb_otg *x)
+{
+	unsigned long flags;
+	struct dwc3_otg *otg;
+
+	if (!x)
+		return -ENODEV;
+
+	otg = otg_to_dwc3_otg(x);
+	otg_dbg(otg, "\n");
+
+	if (!otg->otg.host || !otg->otg.gadget)
+		return -ENODEV;
+
+	spin_lock_irqsave(&otg->lock, flags);
+	otg->user_events |= USER_HNP_EVENT;
+	wakeup_main_thread(otg);
+	spin_unlock_irqrestore(&otg->lock, flags);
+	return 0;
+}
+
+static int dwc3_otg_end_session(struct usb_otg *x)
+{
+	unsigned long flags;
+	struct dwc3_otg *otg;
+
+	if (!x)
+		return -ENODEV;
+
+	otg = otg_to_dwc3_otg(x);
+	otg_dbg(otg, "\n");
+
+	if (!otg->otg.host || !otg->otg.gadget)
+		return -ENODEV;
+
+	spin_lock_irqsave(&otg->lock, flags);
+	otg->user_events |= USER_END_SESSION;
+	wakeup_main_thread(otg);
+	spin_unlock_irqrestore(&otg->lock, flags);
+	return 0;
+}
+
+static int otg_end_session(struct usb_otg *otg)
+{
+	return dwc3_otg_end_session(otg);
+}
+
+static int dwc3_otg_received_host_release(struct usb_otg *x)
+{
+	struct dwc3_otg *otg;
+	unsigned long flags;
+
+	if (!x)
+		return -ENODEV;
+
+	otg = otg_to_dwc3_otg(x);
+	otg_dbg(otg, "\n");
+
+	if (!otg->otg.host || !otg->otg.gadget)
+		return -ENODEV;
+
+	spin_lock_irqsave(&otg->lock, flags);
+	otg->user_events |= PCD_RECEIVED_HOST_RELEASE_EVENT;
+	wakeup_main_thread(otg);
+	spin_unlock_irqrestore(&otg->lock, flags);
+	return 0;
+}
+
+int otg_host_release(struct usb_otg *otg)
+{
+	return dwc3_otg_received_host_release(otg);
+}
+EXPORT_SYMBOL(otg_host_release);
+
+static void dwc3_otg_enable_irq(struct dwc3_otg *otg)
+{
+	u32			reg;
+
+	/* Enable OTG IRQs */
+	reg = OEVT_ALL;
+
+	otg_write(otg, OEVTEN, reg);
+}
+
+static ssize_t store_srp(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	struct usb_phy *phy;
+	struct usb_otg *otg;
+
+	phy = usb_get_phy(USB_PHY_TYPE_USB3);
+	if (IS_ERR(phy) || !phy) {
+		if (!IS_ERR(phy))
+			usb_put_phy(phy);
+		return count;
+	}
+
+	otg = phy->otg;
+	if (!otg) {
+		usb_put_phy(phy);
+		return count;
+	}
+
+	otg_start_srp(otg);
+	usb_put_phy(phy);
+	return count;
+}
+static DEVICE_ATTR(srp, 0220, NULL, store_srp);
+
+static ssize_t store_end(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	struct usb_phy *phy;
+	struct usb_otg *otg;
+
+	phy = usb_get_phy(USB_PHY_TYPE_USB3);
+	if (IS_ERR(phy) || !phy) {
+		if (!IS_ERR(phy))
+			usb_put_phy(phy);
+		return count;
+	}
+
+	otg = phy->otg;
+	if (!otg) {
+		usb_put_phy(phy);
+		return count;
+	}
+
+	otg_end_session(otg);
+	usb_put_phy(phy);
+	return count;
+}
+static DEVICE_ATTR(end, 0220, NULL, store_end);
+
+static ssize_t store_hnp(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count)
+{
+	struct dwc3 *dwc = dev_get_drvdata(dev);
+	struct usb_phy *phy = usb_get_phy(USB_PHY_TYPE_USB3);
+	struct usb_otg *otg;
+
+	dev_dbg(dwc->dev, "%s()\n", __func__);
+
+	if (IS_ERR(phy) || !phy) {
+		dev_info(dwc->dev, "NO PHY!!\n");
+		if (!IS_ERR(phy))
+			usb_put_phy(phy);
+		return count;
+	}
+
+	otg = phy->otg;
+	if (!otg) {
+		dev_info(dwc->dev, "NO OTG!!\n");
+		usb_put_phy(phy);
+		return count;
+	}
+
+	dev_info(dev, "b_hnp_enable is FALSE\n");
+	dwc->gadget->host_request_flag = 1;
+
+	usb_put_phy(phy);
+	return count;
+}
+static DEVICE_ATTR(hnp, 0220, NULL, store_hnp);
+
+static ssize_t store_hnp_end(struct device *dev, struct device_attribute *attr,
+			     const char *buf, size_t count)
+{
+	struct usb_phy *phy;
+	struct usb_otg *otg;
+	unsigned long flags;
+	struct dwc3_otg *dwc_otg;
+
+	phy = usb_get_phy(USB_PHY_TYPE_USB3);
+	if (IS_ERR(phy) || !phy) {
+		if (!IS_ERR(phy))
+			usb_put_phy(phy);
+		return count;
+	}
+
+	otg = phy->otg;
+	if (!otg) {
+		usb_put_phy(phy);
+		return count;
+	}
+
+	dwc_otg = otg_to_dwc3_otg(otg);
+
+	spin_lock_irqsave(&dwc_otg->lock, flags);
+	dwc_otg->user_events |= USER_HNP_END_SESSION;
+	wakeup_main_thread(dwc_otg);
+	spin_unlock_irqrestore(&dwc_otg->lock, flags);
+
+	usb_put_phy(phy);
+	return count;
+}
+static DEVICE_ATTR(hnp_end, 0220, NULL, store_hnp_end);
+
+static ssize_t store_a_hnp_reqd(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct dwc3 *dwc = dev_get_drvdata(dev);
+	struct dwc3_otg *otg;
+
+	otg = dwc->otg;
+	host_release(otg);
+	return count;
+}
+static DEVICE_ATTR(a_hnp_reqd, 0220, NULL, store_a_hnp_reqd);
+
+static ssize_t store_print_dbg(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct dwc3 *dwc = dev_get_drvdata(dev);
+	struct dwc3_otg *otg;
+
+	otg = dwc->otg;
+	print_debug_regs(otg);
+
+	return count;
+}
+static DEVICE_ATTR(print_dbg, 0220, NULL, store_print_dbg);
+
+void dwc_usb3_remove_dev_files(struct device *dev)
+{
+	device_remove_file(dev, &dev_attr_print_dbg);
+	device_remove_file(dev, &dev_attr_a_hnp_reqd);
+	device_remove_file(dev, &dev_attr_end);
+	device_remove_file(dev, &dev_attr_srp);
+	device_remove_file(dev, &dev_attr_hnp);
+	device_remove_file(dev, &dev_attr_hnp_end);
+}
+
+int dwc3_otg_create_dev_files(struct device *dev)
+{
+	int retval;
+
+	retval = device_create_file(dev, &dev_attr_hnp);
+	if (retval)
+		goto fail;
+
+	retval = device_create_file(dev, &dev_attr_hnp_end);
+	if (retval)
+		goto fail;
+
+	retval = device_create_file(dev, &dev_attr_srp);
+	if (retval)
+		goto fail;
+
+	retval = device_create_file(dev, &dev_attr_end);
+	if (retval)
+		goto fail;
+
+	retval = device_create_file(dev, &dev_attr_a_hnp_reqd);
+	if (retval)
+		goto fail;
+
+	retval = device_create_file(dev, &dev_attr_print_dbg);
+	if (retval)
+		goto fail;
+
+	return 0;
+
+fail:
+	dev_err(dev, "Failed to create one or more sysfs files!!\n");
+	return retval;
+}
+
+void dwc3_otg_init(struct dwc3 *dwc)
+{
+	struct dwc3_otg *otg;
+	int err;
+	u32 reg;
+
+	dev_dbg(dwc->dev, "dwc3_otg_init\n");
+
+	/*
+	 * GHWPARAMS6[10] bit is SRPSupport.
+	 * This bit also reflects DWC_USB3_EN_OTG
+	 */
+	reg = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
+	if (!(reg & GHWPARAMS6_SRP_SUPPORT_ENABLED)) {
+		/*
+		 * No OTG support in the HW core.
+		 * We return 0 to indicate no error, since this is acceptable
+		 * situation, just continue probe the dwc3 driver without otg.
+		 */
+		dev_dbg(dwc->dev, "dwc3_otg address space is not supported\n");
+		return;
+	}
+
+	otg = kzalloc(sizeof(*otg), GFP_KERNEL);
+	if (!otg) {
+		dev_err(otg->dev, "failed to allocate memroy\n");
+		return;
+	}
+
+	dwc->otg = otg;
+	otg->dev = dwc->dev;
+	otg->dwc = dwc;
+
+	otg->regs = dwc->regs - DWC3_GLOBALS_REGS_START;
+	otg->otg.usb_phy = kzalloc(sizeof(struct usb_phy), GFP_KERNEL);
+	otg->otg.usb_phy->dev = otg->dev;
+	otg->otg.usb_phy->label = "dwc3_otg";
+	otg->otg.state = OTG_STATE_UNDEFINED;
+	otg->otg.usb_phy->otg = &otg->otg;
+	otg->otg.usb_phy->notify_connect = dwc3_otg_notify_connect;
+	otg->otg.usb_phy->notify_disconnect = dwc3_otg_notify_disconnect;
+
+	otg->otg.start_srp = dwc3_otg_start_srp;
+	otg->otg.start_hnp = dwc3_otg_start_hnp;
+	otg->otg.set_host = dwc3_otg_set_host;
+	otg->otg.set_peripheral = dwc3_otg_set_periph;
+
+	otg->hwparams6 = reg;
+	otg->state = OTG_STATE_UNDEFINED;
+
+	spin_lock_init(&otg->lock);
+	init_waitqueue_head(&otg->main_wq);
+
+	err = usb_add_phy(otg->otg.usb_phy, USB_PHY_TYPE_USB3);
+	if (err) {
+		dev_err(otg->dev, "can't register transceiver, err: %d\n",
+			err);
+		goto exit;
+	}
+
+	otg->irq = platform_get_irq(to_platform_device(otg->dev), 1);
+
+	dwc3_otg_create_dev_files(otg->dev);
+
+	/* Set irq handler */
+	err = request_irq(otg->irq, dwc3_otg_irq, IRQF_SHARED, "dwc3_otg", otg);
+	if (err) {
+		dev_err(otg->otg.usb_phy->dev, "failed to request irq #%d --> %d\n",
+				otg->irq, err);
+		goto exit;
+	}
+
+	dwc3_otg_enable_irq(otg);
+
+	err = dwc3_gadget_init(dwc);
+	if (err) {
+		if (err != -EPROBE_DEFER)
+			dev_err(otg->otg.usb_phy->dev,
+				"failed to initialize gadget\n");
+		goto exit;
+	}
+
+	err = dwc3_host_init(dwc);
+	if (err) {
+		if (err != -EPROBE_DEFER)
+			dev_err(otg->otg.usb_phy->dev,
+				"failed to initialize host\n");
+		goto exit;
+	}
+
+	return;
+
+exit:
+	kfree(otg->otg.usb_phy);
+	kfree(otg);
+}
+
+void dwc3_otg_exit(struct dwc3 *dwc)
+{
+	struct dwc3_otg *otg = dwc->otg;
+
+	otg_dbg(otg, "\n");
+	usb_remove_phy(otg->otg.usb_phy);
+	kfree(otg->otg.usb_phy);
+	kfree(otg);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/otg.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/otg.h
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * otg.h - DesignWare USB3 DRD OTG Header
+ *
+ * Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com
+ *
+ * Authors: Felipe Balbi <balbi@ti.com>,
+ *	    Sebastian Andrzej Siewior <bigeasy@linutronix.de>
+ */
+
+#define otg_dbg(d, fmt, args...)  dev_dbg((d)->dev, "%s(): " fmt,\
+		__func__, ## args)
+#define otg_vdbg(d, fmt, args...) dev_vdbg((d)->dev, "%s(): " fmt,\
+		__func__, ## args)
+#define otg_err(d, fmt, args...)  dev_err((d)->dev, "%s(): ERROR: " fmt,\
+		__func__, ## args)
+#define otg_warn(d, fmt, args...) dev_warn((d)->dev, "%s(): WARN: " fmt,\
+		__func__, ## args)
+#define otg_info(d, fmt, args...) dev_info((d)->dev, "%s(): INFO: " fmt,\
+		__func__, ## args)
+
+#ifdef VERBOSE_DEBUG
+#define otg_write(o, reg, val)	do {					\
+		otg_vdbg(o, "OTG_WRITE: reg=0x%05x, val=0x%08x\n", reg, val); \
+		writel(val, ((void *)((o)->regs)) + reg);	\
+	} while (0)
+
+#define otg_read(o, reg) ({						\
+		u32 __r = readl(((void *)((o)->regs)) + reg);	\
+		otg_vdbg(o, "OTG_READ: reg=0x%05x, val=0x%08x\n", reg, __r); \
+		__r;							\
+	})
+#else
+#define otg_write(o, reg, val)	writel(val, ((void *)((o)->regs)) + reg)
+#define otg_read(o, reg)	readl(((void *)((o)->regs)) + reg)
+#endif
+
+#define sleep_main_thread_until_condition_timeout(otg, condition, msecs) ({ \
+		int __timeout = msecs;				\
+		while (!(condition)) {				\
+			otg_dbg(otg, "  ... sleeping for %d\n", __timeout); \
+			__timeout = sleep_main_thread_timeout(otg, __timeout); \
+			if (__timeout <= 0) {			\
+				break;				\
+			}					\
+		}						\
+		__timeout;					\
+	})
+
+#define sleep_main_thread_until_condition(otg, condition) ({	\
+		int __rc;					\
+		do {						\
+			__rc = sleep_main_thread_until_condition_timeout(otg, \
+					condition, 50000);	\
+		} while (__rc == 0);				\
+		__rc;						\
+	})
+
+#define GHWPARAMS6				0xc158
+#define GHWPARAMS6_SRP_SUPPORT_ENABLED		0x0400
+#define GHWPARAMS6_HNP_SUPPORT_ENABLED		0x0800
+
+#define GCTL					0xc110
+#define GCTL_PRT_CAP_DIR			0x3000
+#define GCTL_PRT_CAP_DIR_SHIFT			12
+#define GCTL_PRT_CAP_DIR_HOST			1
+#define GCTL_PRT_CAP_DIR_DEV			2
+#define GCTL_PRT_CAP_DIR_OTG			3
+#define GCTL_GBL_HIBERNATION_EN			0x2
+
+#define OCFG					0xcc00
+#define OCFG_SRP_CAP				0x01
+#define OCFG_SRP_CAP_SHIFT			0
+#define OCFG_HNP_CAP				0x02
+#define OCFG_HNP_CAP_SHIFT			1
+#define OCFG_OTG_VERSION			0x04
+#define OCFG_OTG_VERSION_SHIFT			2
+
+#define OCTL					0xcc04
+#define OCTL_HST_SET_HNP_EN			0x01
+#define OCTL_HST_SET_HNP_EN_SHIFT		0
+#define OCTL_DEV_SET_HNP_EN			0x02
+#define OCTL_DEV_SET_HNP_EN_SHIFT		1
+#define OCTL_TERM_SEL_DL_PULSE			0x04
+#define OCTL_TERM_SEL_DL_PULSE_SHIFT		2
+#define OCTL_SES_REQ				0x08
+#define OCTL_SES_REQ_SHIFT			3
+#define OCTL_HNP_REQ				0x10
+#define OCTL_HNP_REQ_SHIFT			4
+#define OCTL_PRT_PWR_CTL			0x20
+#define OCTL_PRT_PWR_CTL_SHIFT			5
+#define OCTL_PERI_MODE				0x40
+#define OCTL_PERI_MODE_SHIFT			6
+
+#define OEVT					0xcc08
+#define OEVT_ERR				0x00000001
+#define OEVT_ERR_SHIFT				0
+#define OEVT_SES_REQ_SCS			0x00000002
+#define OEVT_SES_REQ_SCS_SHIFT			1
+#define OEVT_HST_NEG_SCS			0x00000004
+#define OEVT_HST_NEG_SCS_SHIFT			2
+#define OEVT_B_SES_VLD_EVT			0x00000008
+#define OEVT_B_SES_VLD_EVT_SHIFT		3
+#define OEVT_B_DEV_VBUS_CHNG_EVNT		0x00000100
+#define OEVT_B_DEV_VBUS_CHNG_EVNT_SHIFT		8
+#define OEVT_B_DEV_SES_VLD_DET_EVNT		0x00000200
+#define OEVT_B_DEV_SES_VLD_DET_EVNT_SHIFT	9
+#define OEVT_B_DEV_HNP_CHNG_EVNT		0x00000400
+#define OEVT_B_DEV_HNP_CHNG_EVNT_SHIFT		10
+#define OEVT_B_DEV_B_HOST_END_EVNT		0x00000800
+#define OEVT_B_DEV_B_HOST_END_EVNT_SHIFT	11
+#define OEVT_A_DEV_SESS_END_DET_EVNT		0x00010000
+#define OEVT_A_DEV_SESS_END_DET_EVNT_SHIFT	16
+#define OEVT_A_DEV_SRP_DET_EVNT			0x00020000
+#define OEVT_A_DEV_SRP_DET_EVNT_SHIFT		17
+#define OEVT_A_DEV_HNP_CHNG_EVNT		0x00040000
+#define OEVT_A_DEV_HNP_CHNG_EVNT_SHIFT		18
+#define OEVT_A_DEV_HOST_EVNT			0x00080000
+#define OEVT_A_DEV_HOST_EVNT_SHIFT		19
+#define OEVT_A_DEV_B_DEV_HOST_END_EVNT		0x00100000
+#define OEVT_A_DEV_B_DEV_HOST_END_EVNT_SHIFT	20
+#define OEVT_A_DEV_IDLE_EVNT			0x00200000
+#define OEVT_A_DEV_IDLE_EVNT_SHIFT		21
+#define OEVT_HOST_ROLE_REQ_INIT_EVNT		0x00400000
+#define OEVT_HOST_ROLE_REQ_INIT_EVNT_SHIFT	22
+#define OEVT_HOST_ROLE_REQ_CONFIRM_EVNT		0x00800000
+#define OEVT_HOST_ROLE_REQ_CONFIRM_EVNT_SHIFT	23
+#define OEVT_CONN_ID_STS_CHNG_EVNT		0x01000000
+#define OEVT_CONN_ID_STS_CHNG_EVNT_SHIFT	24
+#define OEVT_DEV_MOD_EVNT			0x80000000
+#define OEVT_DEV_MOD_EVNT_SHIFT			31
+
+#define OEVTEN					0xcc0c
+
+#define OEVT_ALL (OEVT_CONN_ID_STS_CHNG_EVNT | \
+		OEVT_HOST_ROLE_REQ_INIT_EVNT | \
+		OEVT_HOST_ROLE_REQ_CONFIRM_EVNT | \
+		OEVT_A_DEV_B_DEV_HOST_END_EVNT | \
+		OEVT_A_DEV_HOST_EVNT | \
+		OEVT_A_DEV_HNP_CHNG_EVNT | \
+		OEVT_A_DEV_SRP_DET_EVNT | \
+		OEVT_A_DEV_SESS_END_DET_EVNT | \
+		OEVT_B_DEV_B_HOST_END_EVNT | \
+		OEVT_B_DEV_HNP_CHNG_EVNT | \
+		OEVT_B_DEV_SES_VLD_DET_EVNT | \
+		OEVT_B_DEV_VBUS_CHNG_EVNT)
+
+#define OSTS					0xcc10
+#define OSTS_CONN_ID_STS			0x0001
+#define OSTS_CONN_ID_STS_SHIFT			0
+#define OSTS_A_SES_VLD				0x0002
+#define OSTS_A_SES_VLD_SHIFT			1
+#define OSTS_B_SES_VLD				0x0004
+#define OSTS_B_SES_VLD_SHIFT			2
+#define OSTS_XHCI_PRT_PWR			0x0008
+#define OSTS_XHCI_PRT_PWR_SHIFT			3
+#define OSTS_PERIP_MODE				0x0010
+#define OSTS_PERIP_MODE_SHIFT			4
+#define OSTS_OTG_STATES				0x0f00
+#define OSTS_OTG_STATE_SHIFT			8
+
+#define DCTL					0xc704
+#define DCTL_RUN_STOP				0x80000000
+
+#define OTG_STATE_INVALID			-1
+#define OTG_STATE_EXIT				14
+#define OTG_STATE_TERMINATED			15
+
+#define PERI_MODE_HOST		0
+#define PERI_MODE_PERIPHERAL	1
+
+/** The main structure to keep track of OTG driver state. */
+struct dwc3_otg {
+
+	/** OTG PHY */
+	struct usb_otg otg;
+	struct device *dev;
+	struct dwc3 *dwc;
+
+	void __iomem *regs;
+
+	int main_wakeup_needed;
+	struct task_struct *main_thread;
+	wait_queue_head_t main_wq;
+
+	spinlock_t lock;
+
+	int otg_srp_reqd;
+
+	/* Events */
+	u32 otg_events;
+
+	u32 user_events;
+
+	/** User initiated SRP.
+	 *
+	 * Valid in B-device during sensing/probing. Initiates SRP signalling
+	 * across the bus.
+	 *
+	 * Also valid as an A-device during probing. This causes the A-device to
+	 * apply V-bus manually and check for a device. Can be used if the
+	 * device does not support SRP and the host does not support ADP.
+	 */
+#define USER_SRP_EVENT			0x1
+	/** User initiated HNP (only valid in B-peripheral) */
+#define USER_HNP_EVENT			0x2
+	/** User has ended the session (only valid in B-peripheral) */
+#define USER_END_SESSION		0x4
+	/** User initiated VBUS. This will cause the A-device to turn on the
+	 * VBUS and see if a device will connect (only valid in A-device during
+	 * sensing/probing)
+	 */
+#define USER_VBUS_ON			0x8
+	/** User has initiated RSP */
+#define USER_RSP_EVENT			0x10
+	/** Host release event */
+#define PCD_RECEIVED_HOST_RELEASE_EVENT	0x20
+	/** Initial SRP */
+#define INITIAL_SRP			0x40
+	/** A-device connected event*/
+#define USER_A_CONN_EVENT		0x80
+	/** User initiated HNP END Session. This will make the A-device and
+	 *  B-device to return back to their previous roles before HNP got
+	 *  initiated
+	 */
+#define USER_HNP_END_SESSION		0x100
+
+	/* States */
+	enum usb_otg_state prev;
+	enum usb_otg_state state;
+
+	u32 hwparams6;
+	int hcd_irq;
+	int irq;
+	int host_started;
+	int peripheral_started;
+	int dev_enum;
+
+	struct delayed_work hp_work;	/* drives HNP polling */
+
+};
+
+extern int usb_port_suspend(struct usb_device *udev, pm_message_t msg);
+extern void usb_kick_hub_wq(struct usb_device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/dwc3/platform_data.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/dwc3/platform_data.h
@@ -0,0 +1,54 @@
+/**
+ * platform_data.h - USB DWC3 Platform Data Support
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Author: Felipe Balbi <balbi@ti.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2  of
+ * the License as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/usb/ch9.h>
+#include <linux/usb/otg.h>
+
+struct dwc3_platform_data {
+	enum usb_device_speed maximum_speed;
+	enum usb_dr_mode dr_mode;
+	bool usb3_lpm_capable;
+
+	unsigned is_utmi_l1_suspend:1;
+	u8 hird_threshold;
+
+	u8 lpm_nyet_threshold;
+
+	unsigned disable_scramble_quirk:1;
+	unsigned has_lpm_erratum:1;
+	unsigned u2exit_lfps_quirk:1;
+	unsigned u2ss_inp3_quirk:1;
+	unsigned req_p1p2p3_quirk:1;
+	unsigned del_p1p2p3_quirk:1;
+	unsigned del_phy_power_chg_quirk:1;
+	unsigned lfps_filter_quirk:1;
+	unsigned rx_detect_poll_quirk:1;
+	unsigned dis_u3_susphy_quirk:1;
+	unsigned dis_u2_susphy_quirk:1;
+	unsigned dis_enblslpm_quirk:1;
+	unsigned dis_rxdet_inp3_quirk:1;
+
+	unsigned tx_de_emphasis_quirk:1;
+	unsigned tx_de_emphasis:2;
+
+	u32 fladj_value;
+	bool refclk_fladj;
+
+	const char *hsphy_interface;
+};
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/early/xhci-dbc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/early/xhci-dbc.c
@@ -14,7 +14,6 @@
 #include <linux/pci_ids.h>
 #include <linux/memblock.h>
 #include <linux/io.h>
-#include <linux/iopoll.h>
 #include <asm/pci-direct.h>
 #include <asm/fixmap.h>
 #include <linux/bcd.h>
@@ -136,9 +135,17 @@
 {
 	u32 result;
 
-	return readl_poll_timeout_atomic(ptr, result,
-					 ((result & mask) == done),
-					 delay, wait);
+	/* Can not use readl_poll_timeout_atomic() for early boot things */
+	do {
+		result = readl(ptr);
+		result &= mask;
+		if (result == done)
+			return 0;
+		udelay(delay);
+		wait -= delay;
+	} while (wait > 0);
+
+	return -ETIMEDOUT;
 }
 
 static void __init xdbc_bios_handoff(void)
@@ -864,7 +871,8 @@
 
 static void early_xdbc_write(struct console *con, const char *str, u32 n)
 {
-	static char buf[XDBC_MAX_PACKET];
+	/* static variables are zeroed, so buf is always NULL terminated */
+	static char buf[XDBC_MAX_PACKET + 1];
 	int chunk, ret;
 	int use_cr = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/composite.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/composite.c
@@ -477,6 +477,46 @@
 }
 EXPORT_SYMBOL_GPL(usb_interface_id);
 
+/**
+ * usb_func_wakeup - sends function wake notification to the host.
+ * @func: function that sends the remote wakeup notification.
+ *
+ * Applicable to devices operating at enhanced superspeed when usb
+ * functions are put in function suspend state and armed for function
+ * remote wakeup. On completion, function wake notification is sent. If
+ * the device is in low power state it tries to bring the device to active
+ * state before sending the wake notification. Since it is a synchronous
+ * call, caller must take care of not calling it in interrupt context.
+ * For devices operating at lower speeds  returns negative errno.
+ *
+ * Returns zero on success, else negative errno.
+ */
+int usb_func_wakeup(struct usb_function *func)
+{
+	struct usb_gadget	*gadget = func->config->cdev->gadget;
+	int			id;
+
+	if (!gadget->ops->func_wakeup)
+		return -EOPNOTSUPP;
+
+	if (!func->func_wakeup_armed) {
+		ERROR(func->config->cdev, "not armed for func remote wakeup\n");
+		return -EINVAL;
+	}
+
+	for (id = 0; id < MAX_CONFIG_INTERFACES; id++)
+		if (func->config->interface[id] == func)
+			break;
+
+	if (id == MAX_CONFIG_INTERFACES) {
+		ERROR(func->config->cdev, "Invalid function\n");
+		return -EINVAL;
+	}
+
+	return gadget->ops->func_wakeup(gadget, id);
+}
+EXPORT_SYMBOL_GPL(usb_func_wakeup);
+
 static u8 encode_bMaxPower(enum usb_device_speed speed,
 		struct usb_configuration *c)
 {
@@ -498,6 +538,19 @@
 		return min(val, 900U) / 8;
 }
 
+void check_remote_wakeup_config(struct usb_gadget *g,
+				struct usb_configuration *c)
+{
+	if (USB_CONFIG_ATT_WAKEUP & c->bmAttributes) {
+		/* Reset the rw bit if gadget is not capable of it */
+		if (!g->wakeup_capable && g->ops->set_remote_wakeup) {
+			WARN(c->cdev, "Clearing wakeup bit for config c.%d\n",
+			     c->bConfigurationValue);
+			c->bmAttributes &= ~USB_CONFIG_ATT_WAKEUP;
+		}
+	}
+}
+
 static int config_buf(struct usb_configuration *config,
 		enum usb_device_speed speed, void *buf, u8 type)
 {
@@ -728,6 +781,17 @@
 						      USB_HIGH_SPEED_OPERATION |
 						      USB_5GBPS_OPERATION);
 		ss_cap->bFunctionalitySupport = USB_LOW_SPEED_OPERATION;
+
+		/* Get Controller configuration */
+		if (cdev->gadget->ops->get_config_params) {
+			cdev->gadget->ops->get_config_params(cdev->gadget,
+				&dcd_config_params);
+		} else {
+			dcd_config_params.bU1devExitLat =
+				USB_DEFAULT_U1_DEV_EXIT_LAT;
+			dcd_config_params.bU2DevExitLat =
+				cpu_to_le16(USB_DEFAULT_U2_DEV_EXIT_LAT);
+		}
 		ss_cap->bU1devExitLat = dcd_config_params.bU1devExitLat;
 		ss_cap->bU2DevExitLat = dcd_config_params.bU2DevExitLat;
 	}
@@ -945,11 +1009,17 @@
 		power = min(power, 500U);
 	else
 		power = min(power, 900U);
-done:
-	if (power <= USB_SELF_POWER_VBUS_MAX_DRAW)
-		usb_gadget_set_selfpowered(gadget);
+
+	if (USB_CONFIG_ATT_WAKEUP & c->bmAttributes)
+		usb_gadget_set_remote_wakeup(gadget, 1);
 	else
+		usb_gadget_set_remote_wakeup(gadget, 0);
+done:
+	if (power > USB_SELF_POWER_VBUS_MAX_DRAW ||
+	    (c && !(c->bmAttributes & USB_CONFIG_ATT_SELFPOWER)))
 		usb_gadget_clear_selfpowered(gadget);
+	else
+		usb_gadget_set_selfpowered(gadget);
 
 	usb_gadget_vbus_draw(gadget, power);
 	if (result >= 0 && cdev->delayed_status)
@@ -1015,6 +1085,10 @@
 		goto done;
 
 	status = bind(config);
+
+	if (status == 0)
+		status = usb_gadget_check_config(cdev->gadget);
+
 	if (status < 0) {
 		while (!list_empty(&config->functions)) {
 			struct usb_function		*f;
@@ -1679,6 +1753,18 @@
 	struct usb_function		*f = NULL;
 	u8				endp;
 
+	if (w_length > USB_COMP_EP0_BUFSIZ) {
+		if (ctrl->bRequestType & USB_DIR_IN) {
+			/* Cast away the const, we are going to overwrite on purpose. */
+			__le16 *temp = (__le16 *)&ctrl->wLength;
+
+			*temp = cpu_to_le16(USB_COMP_EP0_BUFSIZ);
+			w_length = USB_COMP_EP0_BUFSIZ;
+		} else {
+			goto done;
+		}
+	}
+
 	/* partial re-init of the response message; the function or the
 	 * gadget might need to intercept e.g. a control-OUT completion
 	 * when we delegate to it.
@@ -1943,6 +2029,18 @@
 			memset(buf, 0, w_length);
 			buf[5] = 0x01;
 			switch (ctrl->bRequestType & USB_RECIP_MASK) {
+			/*
+			 * The Microsoft CompatID OS Descriptor Spec(w_index = 0x4) and
+			 * Extended Prop OS Desc Spec(w_index = 0x5) state that the
+			 * HighByte of wValue is the InterfaceNumber and the LowByte is
+			 * the PageNumber. This high/low byte ordering is incorrectly
+			 * documented in the Spec. USB analyzer output on the below
+			 * request packets show the high/low byte inverted i.e LowByte
+			 * is the InterfaceNumber and the HighByte is the PageNumber.
+			 * Since we dont support >64KB CompatID/ExtendedProp descriptors,
+			 * PageNumber is set to 0. Hence verify that the HighByte is 0
+			 * for below two cases.
+			 */
 			case USB_RECIP_DEVICE:
 				if (w_index != 0x4 || (w_value >> 8))
 					break;
@@ -1963,6 +2061,9 @@
 				if (w_index != 0x5 || (w_value >> 8))
 					break;
 				interface = w_value & 0xFF;
+				if (interface >= MAX_CONFIG_INTERFACES ||
+				    !os_desc_cfg->interface[interface])
+					break;
 				buf[6] = w_index;
 				count = count_ext_prop(os_desc_cfg,
 					interface);
@@ -2209,7 +2310,7 @@
 	if (!cdev->req)
 		return -ENOMEM;
 
-	cdev->req->buf = kmalloc(USB_COMP_EP0_BUFSIZ, GFP_KERNEL);
+	cdev->req->buf = kzalloc(USB_COMP_EP0_BUFSIZ, GFP_KERNEL);
 	if (!cdev->req->buf)
 		goto fail;
 
@@ -2386,7 +2487,10 @@
 
 	cdev->suspended = 1;
 
-	usb_gadget_set_selfpowered(gadget);
+	if (cdev->config &&
+	    cdev->config->bmAttributes & USB_CONFIG_ATT_SELFPOWER)
+		usb_gadget_set_selfpowered(gadget);
+
 	usb_gadget_vbus_draw(gadget, 2);
 }
 
@@ -2415,8 +2519,11 @@
 		else
 			maxpower = min(maxpower, 900U);
 
-		if (maxpower > USB_SELF_POWER_VBUS_MAX_DRAW)
+		if (maxpower > USB_SELF_POWER_VBUS_MAX_DRAW ||
+		    !(cdev->config->bmAttributes & USB_CONFIG_ATT_SELFPOWER))
 			usb_gadget_clear_selfpowered(gadget);
+		else
+			usb_gadget_set_selfpowered(gadget);
 
 		usb_gadget_vbus_draw(gadget, maxpower);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/configfs.c
@@ -104,9 +104,12 @@
 	int ret;
 	char *str;
 	char *copy = *s_copy;
+
 	ret = strlen(s);
 	if (ret > USB_MAX_STRING_LEN)
 		return -EOVERFLOW;
+	if (ret < 1)
+		return -EINVAL;
 
 	if (copy) {
 		str = copy;
@@ -416,10 +419,9 @@
 	struct usb_composite_dev *cdev = cfg->c.cdev;
 	struct gadget_info *gi = container_of(cdev, struct gadget_info, cdev);
 
-	struct config_group *group = to_config_group(usb_func_ci);
-	struct usb_function_instance *fi = container_of(group,
-			struct usb_function_instance, group);
-	struct usb_function_instance *a_fi;
+	struct usb_function_instance *fi =
+			to_usb_function_instance(usb_func_ci);
+	struct usb_function_instance *a_fi = NULL, *iter;
 	struct usb_function *f;
 	int ret;
 
@@ -429,11 +431,19 @@
 	 * from another gadget or a random directory.
 	 * Also a function instance can only be linked once.
 	 */
-	list_for_each_entry(a_fi, &gi->available_func, cfs_list) {
-		if (a_fi == fi)
-			break;
+
+	if (gi->composite.gadget_driver.udc_name) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	list_for_each_entry(iter, &gi->available_func, cfs_list) {
+		if (iter != fi)
+			continue;
+		a_fi = iter;
+		break;
 	}
-	if (a_fi != fi) {
+	if (!a_fi) {
 		ret = -EINVAL;
 		goto out;
 	}
@@ -467,9 +477,8 @@
 	struct usb_composite_dev *cdev = cfg->c.cdev;
 	struct gadget_info *gi = container_of(cdev, struct gadget_info, cdev);
 
-	struct config_group *group = to_config_group(usb_func_ci);
-	struct usb_function_instance *fi = container_of(group,
-			struct usb_function_instance, group);
+	struct usb_function_instance *fi =
+			to_usb_function_instance(usb_func_ci);
 	struct usb_function *f;
 
 	/*
@@ -890,18 +899,18 @@
 	struct gadget_info *gi = container_of(to_config_group(os_desc_ci),
 					struct gadget_info, os_desc_group);
 	struct usb_composite_dev *cdev = &gi->cdev;
-	struct config_usb_cfg *c_target =
-		container_of(to_config_group(usb_cfg_ci),
-			     struct config_usb_cfg, group);
-	struct usb_configuration *c;
+	struct config_usb_cfg *c_target = to_config_usb_cfg(usb_cfg_ci);
+	struct usb_configuration *c = NULL, *iter;
 	int ret;
 
 	mutex_lock(&gi->lock);
-	list_for_each_entry(c, &cdev->configs, list) {
-		if (c == &c_target->c)
-			break;
+	list_for_each_entry(iter, &cdev->configs, list) {
+		if (iter != &c_target->c)
+			continue;
+		c = iter;
+		break;
 	}
-	if (c != &c_target->c) {
+	if (!c) {
 		ret = -EINVAL;
 		goto out;
 	}
@@ -1378,6 +1387,9 @@
 		if (gadget_is_otg(gadget))
 			c->descriptors = otg_desc;
 
+		/* Properly configure the bmAttributes wakeup bit */
+		check_remote_wakeup_config(gadget, c);
+
 		cfg = container_of(c, struct config_usb_cfg, c);
 		if (!list_empty(&cfg->string_list)) {
 			i = 0;
@@ -1447,6 +1459,8 @@
 	usb_ep_autoconfig_reset(cdev->gadget);
 	spin_lock_irqsave(&gi->spinlock, flags);
 	cdev->gadget = NULL;
+	cdev->deactivations = 0;
+	gadget->deactivated = false;
 	set_gadget_data(gadget, NULL);
 	spin_unlock_irqrestore(&gi->spinlock, flags);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_fs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_fs.c
@@ -122,8 +122,6 @@
 	struct usb_endpoint_descriptor	*descs[3];
 
 	u8				num;
-
-	int				status;	/* P: epfile->mutex */
 };
 
 struct ffs_epfile {
@@ -227,6 +225,9 @@
 	bool use_sg;
 
 	struct ffs_data *ffs;
+
+	int status;
+	struct completion done;
 };
 
 struct ffs_desc_helper {
@@ -278,6 +279,11 @@
 	struct usb_request *req = ffs->ep0req;
 	int ret;
 
+	if (!req) {
+		spin_unlock_irq(&ffs->ev.waitq.lock);
+		return -EINVAL;
+	}
+
 	req->zero     = len < le16_to_cpu(ffs->ev.setup.wLength);
 
 	spin_unlock_irq(&ffs->ev.waitq.lock);
@@ -614,7 +620,7 @@
 	file->private_data = ffs;
 	ffs_data_opened(ffs);
 
-	return 0;
+	return stream_open(inode, file);
 }
 
 static int ffs_ep0_release(struct inode *inode, struct file *file)
@@ -707,12 +713,15 @@
 
 static void ffs_epfile_io_complete(struct usb_ep *_ep, struct usb_request *req)
 {
+	struct ffs_io_data *io_data = req->context;
+
 	ENTER();
-	if (req->context) {
-		struct ffs_ep *ep = _ep->driver_data;
-		ep->status = req->status ? req->status : req->actual;
-		complete(req->context);
-	}
+	if (req->status)
+		io_data->status = req->status;
+	else
+		io_data->status = req->actual;
+
+	complete(&io_data->done);
 }
 
 static ssize_t ffs_copy_to_iter(void *data, int data_len, struct iov_iter *iter)
@@ -821,9 +830,9 @@
 {
 	struct ffs_io_data *io_data = container_of(work, struct ffs_io_data,
 						   work);
-	int ret = io_data->req->status ? io_data->req->status :
-					 io_data->req->actual;
+	int ret = io_data->status;
 	bool kiocb_has_eventfd = io_data->kiocb->ki_flags & IOCB_EVENTFD;
+	unsigned long flags;
 
 	if (io_data->read && ret > 0) {
 		kthread_use_mm(io_data->mm);
@@ -836,7 +845,10 @@
 	if (io_data->ffs->ffs_eventfd && !kiocb_has_eventfd)
 		eventfd_signal(io_data->ffs->ffs_eventfd, 1);
 
+	spin_lock_irqsave(&io_data->ffs->eps_lock, flags);
 	usb_ep_free_request(io_data->ep, io_data->req);
+	io_data->req = NULL;
+	spin_unlock_irqrestore(&io_data->ffs->eps_lock, flags);
 
 	if (io_data->read)
 		kfree(io_data->to_free);
@@ -852,6 +864,8 @@
 
 	ENTER();
 
+	io_data->status = req->status ? req->status : req->actual;
+
 	INIT_WORK(&io_data->work, ffs_user_copy_worker);
 	queue_work(ffs->io_completion_wq, &io_data->work);
 }
@@ -1050,7 +1064,6 @@
 		WARN(1, "%s: data_len == -EINVAL\n", __func__);
 		ret = -EINVAL;
 	} else if (!io_data->aio) {
-		DECLARE_COMPLETION_ONSTACK(done);
 		bool interrupted = false;
 
 		req = ep->req;
@@ -1066,7 +1079,8 @@
 
 		io_data->buf = data;
 
-		req->context  = &done;
+		init_completion(&io_data->done);
+		req->context  = io_data;
 		req->complete = ffs_epfile_io_complete;
 
 		ret = usb_ep_queue(ep->ep, req, GFP_ATOMIC);
@@ -1075,7 +1089,12 @@
 
 		spin_unlock_irq(&epfile->ffs->eps_lock);
 
-		if (wait_for_completion_interruptible(&done)) {
+		if (wait_for_completion_interruptible(&io_data->done)) {
+			spin_lock_irq(&epfile->ffs->eps_lock);
+			if (epfile->ep != ep) {
+				ret = -ESHUTDOWN;
+				goto error_lock;
+			}
 			/*
 			 * To avoid race condition with ffs_epfile_io_complete,
 			 * dequeue the request first then check
@@ -1083,17 +1102,18 @@
 			 * condition with req->complete callback.
 			 */
 			usb_ep_dequeue(ep->ep, req);
-			wait_for_completion(&done);
-			interrupted = ep->status < 0;
+			spin_unlock_irq(&epfile->ffs->eps_lock);
+			wait_for_completion(&io_data->done);
+			interrupted = io_data->status < 0;
 		}
 
 		if (interrupted)
 			ret = -EINTR;
-		else if (io_data->read && ep->status > 0)
-			ret = __ffs_epfile_read_data(epfile, data, ep->status,
+		else if (io_data->read && io_data->status > 0)
+			ret = __ffs_epfile_read_data(epfile, data, io_data->status,
 						     &io_data->data);
 		else
-			ret = ep->status;
+			ret = io_data->status;
 		goto error_mutex;
 	} else if (!(req = usb_ep_alloc_request(ep->ep, GFP_ATOMIC))) {
 		ret = -ENOMEM;
@@ -1154,7 +1174,7 @@
 	file->private_data = epfile;
 	ffs_data_opened(epfile->ffs);
 
-	return 0;
+	return stream_open(inode, file);
 }
 
 static int ffs_aio_cancel(struct kiocb *kiocb)
@@ -1711,16 +1731,24 @@
 
 static void ffs_data_closed(struct ffs_data *ffs)
 {
+	struct ffs_epfile *epfiles;
+	unsigned long flags;
+
 	ENTER();
 
 	if (atomic_dec_and_test(&ffs->opened)) {
 		if (ffs->no_disconnect) {
 			ffs->state = FFS_DEACTIVATED;
-			if (ffs->epfiles) {
-				ffs_epfiles_destroy(ffs->epfiles,
-						   ffs->eps_count);
-				ffs->epfiles = NULL;
-			}
+			spin_lock_irqsave(&ffs->eps_lock, flags);
+			epfiles = ffs->epfiles;
+			ffs->epfiles = NULL;
+			spin_unlock_irqrestore(&ffs->eps_lock,
+							flags);
+
+			if (epfiles)
+				ffs_epfiles_destroy(epfiles,
+						 ffs->eps_count);
+
 			if (ffs->setup_state == FFS_SETUP_PENDING)
 				__ffs_ep0_stall(ffs);
 		} else {
@@ -1767,17 +1795,34 @@
 
 static void ffs_data_clear(struct ffs_data *ffs)
 {
+	struct ffs_epfile *epfiles;
+	unsigned long flags;
+
 	ENTER();
 
 	ffs_closed(ffs);
 
 	BUG_ON(ffs->gadget);
 
-	if (ffs->epfiles)
-		ffs_epfiles_destroy(ffs->epfiles, ffs->eps_count);
+	spin_lock_irqsave(&ffs->eps_lock, flags);
+	epfiles = ffs->epfiles;
+	ffs->epfiles = NULL;
+	spin_unlock_irqrestore(&ffs->eps_lock, flags);
 
-	if (ffs->ffs_eventfd)
+	/*
+	 * potential race possible between ffs_func_eps_disable
+	 * & ffs_epfile_release therefore maintaining a local
+	 * copy of epfile will save us from use-after-free.
+	 */
+	if (epfiles) {
+		ffs_epfiles_destroy(epfiles, ffs->eps_count);
+		ffs->epfiles = NULL;
+	}
+
+	if (ffs->ffs_eventfd) {
 		eventfd_ctx_put(ffs->ffs_eventfd);
+		ffs->ffs_eventfd = NULL;
+	}
 
 	kfree(ffs->raw_descs_data);
 	kfree(ffs->raw_strings);
@@ -1790,7 +1835,6 @@
 
 	ffs_data_clear(ffs);
 
-	ffs->epfiles = NULL;
 	ffs->raw_descs_data = NULL;
 	ffs->raw_descs = NULL;
 	ffs->raw_strings = NULL;
@@ -1824,7 +1868,7 @@
 
 	ENTER();
 
-	if (WARN_ON(ffs->state != FFS_ACTIVE
+	if ((ffs->state != FFS_ACTIVE
 		 || test_and_set_bit(FFS_FL_BOUND, &ffs->flags)))
 		return -EBADFD;
 
@@ -1858,10 +1902,14 @@
 	ENTER();
 
 	if (!WARN_ON(!ffs->gadget)) {
+		/* dequeue before freeing ep0req */
+		usb_ep_dequeue(ffs->gadget->ep0, ffs->ep0req);
+		mutex_lock(&ffs->mutex);
 		usb_ep_free_request(ffs->gadget->ep0, ffs->ep0req);
 		ffs->ep0req = NULL;
 		ffs->gadget = NULL;
 		clear_bit(FFS_FL_BOUND, &ffs->flags);
+		mutex_unlock(&ffs->mutex);
 		ffs_data_put(ffs);
 	}
 }
@@ -1919,12 +1967,15 @@
 
 static void ffs_func_eps_disable(struct ffs_function *func)
 {
-	struct ffs_ep *ep         = func->eps;
-	struct ffs_epfile *epfile = func->ffs->epfiles;
-	unsigned count            = func->ffs->eps_count;
+	struct ffs_ep *ep;
+	struct ffs_epfile *epfile;
+	unsigned short count;
 	unsigned long flags;
 
 	spin_lock_irqsave(&func->ffs->eps_lock, flags);
+	count = func->ffs->eps_count;
+	epfile = func->ffs->epfiles;
+	ep = func->eps;
 	while (count--) {
 		/* pending requests get nuked */
 		if (ep->ep)
@@ -1942,14 +1993,18 @@
 
 static int ffs_func_eps_enable(struct ffs_function *func)
 {
-	struct ffs_data *ffs      = func->ffs;
-	struct ffs_ep *ep         = func->eps;
-	struct ffs_epfile *epfile = ffs->epfiles;
-	unsigned count            = ffs->eps_count;
+	struct ffs_data *ffs;
+	struct ffs_ep *ep;
+	struct ffs_epfile *epfile;
+	unsigned short count;
 	unsigned long flags;
 	int ret = 0;
 
 	spin_lock_irqsave(&func->ffs->eps_lock, flags);
+	ffs = func->ffs;
+	ep = func->eps;
+	epfile = ffs->epfiles;
+	count = ffs->eps_count;
 	while(count--) {
 		ep->ep->driver_data = ep;
 
@@ -3364,7 +3419,7 @@
 	__ffs_event_add(ffs, FUNCTIONFS_SETUP);
 	spin_unlock_irqrestore(&ffs->ev.waitq.lock, flags);
 
-	return creq->wLength == 0 ? USB_GADGET_DELAYED_STATUS : 0;
+	return ffs->ev.setup.wLength == 0 ? USB_GADGET_DELAYED_STATUS : 0;
 }
 
 static bool ffs_func_req_match(struct usb_function *f,
@@ -3570,6 +3625,7 @@
 	/* Drain any pending AIO completions */
 	drain_workqueue(ffs->io_completion_wq);
 
+	ffs_event_add(ffs, FUNCTIONFS_UNBIND);
 	if (!--opts->refcnt)
 		functionfs_unbind(ffs);
 
@@ -3594,7 +3650,6 @@
 	func->function.ssp_descriptors = NULL;
 	func->interfaces_nums = NULL;
 
-	ffs_event_add(ffs, FUNCTIONFS_UNBIND);
 }
 
 static struct usb_function *ffs_alloc(struct usb_function_instance *fi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_hid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_hid.c
@@ -71,7 +71,7 @@
 	wait_queue_head_t		write_queue;
 	struct usb_request		*req;
 
-	int				minor;
+	struct device			dev;
 	struct cdev			cdev;
 	struct usb_function		func;
 
@@ -84,6 +84,15 @@
 	return container_of(f, struct f_hidg, func);
 }
 
+static void hidg_release(struct device *dev)
+{
+	struct f_hidg *hidg = container_of(dev, struct f_hidg, dev);
+
+	kfree(hidg->report_desc);
+	kfree(hidg->set_report_buf);
+	kfree(hidg);
+}
+
 /*-------------------------------------------------------------------------*/
 /*                           Static descriptors                            */
 
@@ -904,9 +913,7 @@
 	struct usb_ep		*ep;
 	struct f_hidg		*hidg = func_to_hidg(f);
 	struct usb_string	*us;
-	struct device		*device;
 	int			status;
-	dev_t			dev;
 
 	/* maybe allocate device-global string IDs, and patch descriptors */
 	us = usb_gstrings_attach(c->cdev, ct_func_strings,
@@ -999,21 +1006,11 @@
 
 	/* create char device */
 	cdev_init(&hidg->cdev, &f_hidg_fops);
-	dev = MKDEV(major, hidg->minor);
-	status = cdev_add(&hidg->cdev, dev, 1);
+	status = cdev_device_add(&hidg->cdev, &hidg->dev);
 	if (status)
 		goto fail_free_descs;
 
-	device = device_create(hidg_class, NULL, dev, NULL,
-			       "%s%d", "hidg", hidg->minor);
-	if (IS_ERR(device)) {
-		status = PTR_ERR(device);
-		goto del;
-	}
-
 	return 0;
-del:
-	cdev_del(&hidg->cdev);
 fail_free_descs:
 	usb_free_all_descriptors(f);
 fail:
@@ -1244,9 +1241,7 @@
 
 	hidg = func_to_hidg(f);
 	opts = container_of(f->fi, struct f_hid_opts, func_inst);
-	kfree(hidg->report_desc);
-	kfree(hidg->set_report_buf);
-	kfree(hidg);
+	put_device(&hidg->dev);
 	mutex_lock(&opts->lock);
 	--opts->refcnt;
 	mutex_unlock(&opts->lock);
@@ -1256,8 +1251,7 @@
 {
 	struct f_hidg *hidg = func_to_hidg(f);
 
-	device_destroy(hidg_class, MKDEV(major, hidg->minor));
-	cdev_del(&hidg->cdev);
+	cdev_device_del(&hidg->cdev, &hidg->dev);
 
 	usb_free_all_descriptors(f);
 }
@@ -1266,6 +1260,7 @@
 {
 	struct f_hidg *hidg;
 	struct f_hid_opts *opts;
+	int ret;
 
 	/* allocate and initialize one new instance */
 	hidg = kzalloc(sizeof(*hidg), GFP_KERNEL);
@@ -1277,7 +1272,17 @@
 	mutex_lock(&opts->lock);
 	++opts->refcnt;
 
-	hidg->minor = opts->minor;
+	device_initialize(&hidg->dev);
+	hidg->dev.release = hidg_release;
+	hidg->dev.class = hidg_class;
+	hidg->dev.devt = MKDEV(major, opts->minor);
+	ret = dev_set_name(&hidg->dev, "hidg%d", opts->minor);
+	if (ret) {
+		--opts->refcnt;
+		mutex_unlock(&opts->lock);
+		return ERR_PTR(ret);
+	}
+
 	hidg->bInterfaceSubClass = opts->subclass;
 	hidg->bInterfaceProtocol = opts->protocol;
 	hidg->report_length = opts->report_length;
@@ -1287,7 +1292,8 @@
 					    opts->report_desc_length,
 					    GFP_KERNEL);
 		if (!hidg->report_desc) {
-			kfree(hidg);
+			put_device(&hidg->dev);
+			--opts->refcnt;
 			mutex_unlock(&opts->lock);
 			return ERR_PTR(-ENOMEM);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_mass_storage.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_mass_storage.c
@@ -543,21 +543,37 @@
 
 static bool start_in_transfer(struct fsg_common *common, struct fsg_buffhd *bh)
 {
+	int rc;
+
 	if (!fsg_is_set(common))
 		return false;
 	bh->state = BUF_STATE_SENDING;
-	if (start_transfer(common->fsg, common->fsg->bulk_in, bh->inreq))
+	rc = start_transfer(common->fsg, common->fsg->bulk_in, bh->inreq);
+	if (rc) {
 		bh->state = BUF_STATE_EMPTY;
+		if (rc == -ESHUTDOWN) {
+			common->running = 0;
+			return false;
+		}
+	}
 	return true;
 }
 
 static bool start_out_transfer(struct fsg_common *common, struct fsg_buffhd *bh)
 {
+	int rc;
+
 	if (!fsg_is_set(common))
 		return false;
 	bh->state = BUF_STATE_RECEIVING;
-	if (start_transfer(common->fsg, common->fsg->bulk_out, bh->outreq))
+	rc = start_transfer(common->fsg, common->fsg->bulk_out, bh->outreq);
+	if (rc) {
 		bh->state = BUF_STATE_FULL;
+		if (rc == -ESHUTDOWN) {
+			common->running = 0;
+			return false;
+		}
+	}
 	return true;
 }
 
@@ -588,7 +604,7 @@
 static int do_read(struct fsg_common *common)
 {
 	struct fsg_lun		*curlun = common->curlun;
-	u32			lba;
+	u64			lba;
 	struct fsg_buffhd	*bh;
 	int			rc;
 	u32			amount_left;
@@ -603,7 +619,10 @@
 	if (common->cmnd[0] == READ_6)
 		lba = get_unaligned_be24(&common->cmnd[1]);
 	else {
-		lba = get_unaligned_be32(&common->cmnd[2]);
+		if (common->cmnd[0] == READ_16)
+			lba = get_unaligned_be64(&common->cmnd[2]);
+		else		/* READ_10 or READ_12 */
+			lba = get_unaligned_be32(&common->cmnd[2]);
 
 		/*
 		 * We allow DPO (Disable Page Out = don't save data in the
@@ -716,7 +735,7 @@
 static int do_write(struct fsg_common *common)
 {
 	struct fsg_lun		*curlun = common->curlun;
-	u32			lba;
+	u64			lba;
 	struct fsg_buffhd	*bh;
 	int			get_some_more;
 	u32			amount_left_to_req, amount_left_to_write;
@@ -740,7 +759,10 @@
 	if (common->cmnd[0] == WRITE_6)
 		lba = get_unaligned_be24(&common->cmnd[1]);
 	else {
-		lba = get_unaligned_be32(&common->cmnd[2]);
+		if (common->cmnd[0] == WRITE_16)
+			lba = get_unaligned_be64(&common->cmnd[2]);
+		else		/* WRITE_10 or WRITE_12 */
+			lba = get_unaligned_be32(&common->cmnd[2]);
 
 		/*
 		 * We allow DPO (Disable Page Out = don't save data in the
@@ -919,7 +941,7 @@
 {
 	struct file	*filp = curlun->filp;
 	struct inode	*inode = file_inode(filp);
-	unsigned long	rc;
+	unsigned long __maybe_unused	rc;
 
 	rc = invalidate_mapping_pages(inode->i_mapping, 0, -1);
 	VLDBG(curlun, "invalidate_mapping_pages -> %ld\n", rc);
@@ -1115,6 +1137,7 @@
 	u32		lba = get_unaligned_be32(&common->cmnd[2]);
 	int		pmi = common->cmnd[8];
 	u8		*buf = (u8 *)bh->buf;
+	u32		max_lba;
 
 	/* Check the PMI and LBA fields */
 	if (pmi > 1 || (pmi == 0 && lba != 0)) {
@@ -1122,12 +1145,37 @@
 		return -EINVAL;
 	}
 
-	put_unaligned_be32(curlun->num_sectors - 1, &buf[0]);
-						/* Max logical block */
-	put_unaligned_be32(curlun->blksize, &buf[4]);/* Block length */
+	if (curlun->num_sectors < 0x100000000ULL)
+		max_lba = curlun->num_sectors - 1;
+	else
+		max_lba = 0xffffffff;
+	put_unaligned_be32(max_lba, &buf[0]);		/* Max logical block */
+	put_unaligned_be32(curlun->blksize, &buf[4]);	/* Block length */
 	return 8;
 }
 
+static int do_read_capacity_16(struct fsg_common *common, struct fsg_buffhd *bh)
+{
+	struct fsg_lun  *curlun = common->curlun;
+	u64		lba = get_unaligned_be64(&common->cmnd[2]);
+	int		pmi = common->cmnd[14];
+	u8		*buf = (u8 *)bh->buf;
+
+	/* Check the PMI and LBA fields */
+	if (pmi > 1 || (pmi == 0 && lba != 0)) {
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+
+	put_unaligned_be64(curlun->num_sectors - 1, &buf[0]);
+							/* Max logical block */
+	put_unaligned_be32(curlun->blksize, &buf[8]);	/* Block length */
+
+	/* It is safe to keep other fields zeroed */
+	memset(&buf[12], 0, 32 - 12);
+	return 32;
+}
+
 static int do_read_header(struct fsg_common *common, struct fsg_buffhd *bh)
 {
 	struct fsg_lun	*curlun = common->curlun;
@@ -1874,6 +1922,17 @@
 			reply = do_read(common);
 		break;
 
+	case READ_16:
+		common->data_size_from_cmnd =
+				get_unaligned_be32(&common->cmnd[10]);
+		reply = check_command_size_in_blocks(common, 16,
+				      DATA_DIR_TO_HOST,
+				      (1<<1) | (0xff<<2) | (0xf<<10), 1,
+				      "READ(16)");
+		if (reply == 0)
+			reply = do_read(common);
+		break;
+
 	case READ_CAPACITY:
 		common->data_size_from_cmnd = 8;
 		reply = check_command(common, 10, DATA_DIR_TO_HOST,
@@ -1926,6 +1985,25 @@
 			reply = do_request_sense(common, bh);
 		break;
 
+	case SERVICE_ACTION_IN_16:
+		switch (common->cmnd[1] & 0x1f) {
+
+		case SAI_READ_CAPACITY_16:
+			common->data_size_from_cmnd =
+				get_unaligned_be32(&common->cmnd[10]);
+			reply = check_command(common, 16, DATA_DIR_TO_HOST,
+					      (1<<1) | (0xff<<2) | (0xf<<10) |
+					      (1<<14), 1,
+					      "READ CAPACITY(16)");
+			if (reply == 0)
+				reply = do_read_capacity_16(common, bh);
+			break;
+
+		default:
+			goto unknown_cmnd;
+		}
+		break;
+
 	case START_STOP:
 		common->data_size_from_cmnd = 0;
 		reply = check_command(common, 6, DATA_DIR_NONE,
@@ -1996,6 +2074,17 @@
 		if (reply == 0)
 			reply = do_write(common);
 		break;
+
+	case WRITE_16:
+		common->data_size_from_cmnd =
+				get_unaligned_be32(&common->cmnd[10]);
+		reply = check_command_size_in_blocks(common, 16,
+				      DATA_DIR_FROM_HOST,
+				      (1<<1) | (0xff<<2) | (0xf<<10), 1,
+				      "WRITE(16)");
+		if (reply == 0)
+			reply = do_write(common);
+		break;
 
 	/*
 	 * Some mandatory commands that we recognize but don't implement.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_midi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_midi.c
@@ -282,7 +282,7 @@
 			/* Our transmit completed. See if there's more to go.
 			 * f_midi_transmit eats req, don't queue it again. */
 			req->length = 0;
-			f_midi_transmit(midi);
+			queue_work(system_highpri_wq, &midi->work);
 			return;
 		}
 		break;
@@ -999,11 +999,11 @@
 	}
 
 	/* configure the endpoint descriptors ... */
-	ms_out_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->in_ports);
-	ms_out_desc.bNumEmbMIDIJack = midi->in_ports;
+	ms_out_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->out_ports);
+	ms_out_desc.bNumEmbMIDIJack = midi->out_ports;
 
-	ms_in_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->out_ports);
-	ms_in_desc.bNumEmbMIDIJack = midi->out_ports;
+	ms_in_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->in_ports);
+	ms_in_desc.bNumEmbMIDIJack = midi->in_ports;
 
 	/* ... and add them to the list */
 	endpoint_descriptor_index = i;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_ncm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_ncm.c
@@ -83,7 +83,9 @@
 /* peak (theoretical) bulk transfer rate in bits-per-second */
 static inline unsigned ncm_bitrate(struct usb_gadget *g)
 {
-	if (gadget_is_superspeed(g) && g->speed >= USB_SPEED_SUPER_PLUS)
+	if (!g)
+		return 0;
+	else if (gadget_is_superspeed(g) && g->speed >= USB_SPEED_SUPER_PLUS)
 		return 4250000000U;
 	else if (gadget_is_superspeed(g) && g->speed == USB_SPEED_SUPER)
 		return 3750000000U;
@@ -886,7 +888,7 @@
 		if (alt > 1)
 			goto fail;
 
-		if (ncm->port.in_ep->enabled) {
+		if (ncm->netdev) {
 			DBG(cdev, "reset ncm\n");
 			ncm->netdev = NULL;
 			gether_disconnect(&ncm->port);
@@ -1173,7 +1175,8 @@
 			  struct sk_buff_head *list)
 {
 	struct f_ncm	*ncm = func_to_ncm(&port->func);
-	__le16		*tmp = (void *) skb->data;
+	unsigned char	*ntb_ptr = skb->data;
+	__le16		*tmp;
 	unsigned	index, index2;
 	int		ndp_index;
 	unsigned	dg_len, dg_len2;
@@ -1186,6 +1189,10 @@
 	const struct ndp_parser_opts *opts = ncm->parser_opts;
 	unsigned	crc_len = ncm->is_crc ? sizeof(uint32_t) : 0;
 	int		dgram_counter;
+	int		to_process = skb->len;
+
+parse_ntb:
+	tmp = (__le16 *)ntb_ptr;
 
 	/* dwSignature */
 	if (get_unaligned_le32(tmp) != opts->nth_sign) {
@@ -1232,7 +1239,7 @@
 		 * walk through NDP
 		 * dwSignature
 		 */
-		tmp = (void *)(skb->data + ndp_index);
+		tmp = (__le16 *)(ntb_ptr + ndp_index);
 		if (get_unaligned_le32(tmp) != ncm->ndp_sign) {
 			INFO(port->func.config->cdev, "Wrong NDP SIGN\n");
 			goto err;
@@ -1289,11 +1296,11 @@
 			if (ncm->is_crc) {
 				uint32_t crc, crc2;
 
-				crc = get_unaligned_le32(skb->data +
+				crc = get_unaligned_le32(ntb_ptr +
 							 index + dg_len -
 							 crc_len);
 				crc2 = ~crc32_le(~0,
-						 skb->data + index,
+						 ntb_ptr + index,
 						 dg_len - crc_len);
 				if (crc != crc2) {
 					INFO(port->func.config->cdev,
@@ -1320,7 +1327,7 @@
 							 dg_len - crc_len);
 			if (skb2 == NULL)
 				goto err;
-			skb_put_data(skb2, skb->data + index,
+			skb_put_data(skb2, ntb_ptr + index,
 				     dg_len - crc_len);
 
 			skb_queue_tail(list, skb2);
@@ -1333,10 +1340,25 @@
 		} while (ndp_len > 2 * (opts->dgram_item_len * 2));
 	} while (ndp_index);
 
-	dev_consume_skb_any(skb);
-
 	VDBG(port->func.config->cdev,
 	     "Parsed NTB with %d frames\n", dgram_counter);
+
+	to_process -= block_len;
+
+	/*
+	 * Windows NCM driver avoids USB ZLPs by adding a 1-byte
+	 * zero pad as needed.
+	 */
+	if (to_process == 1 &&
+	    (*(unsigned char *)(ntb_ptr + block_len) == 0x00)) {
+		to_process--;
+	} else if ((to_process > 0) && (block_len != 0)) {
+		ntb_ptr = (unsigned char *)(ntb_ptr + block_len);
+		goto parse_ntb;
+	}
+
+	dev_consume_skb_any(skb);
+
 	return 0;
 err:
 	skb_queue_purge(list);
@@ -1351,7 +1373,7 @@
 
 	DBG(cdev, "ncm deactivated\n");
 
-	if (ncm->port.in_ep->enabled) {
+	if (ncm->netdev) {
 		ncm->netdev = NULL;
 		gether_disconnect(&ncm->port);
 	}
@@ -1415,7 +1437,7 @@
 	struct usb_composite_dev *cdev = c->cdev;
 	struct f_ncm		*ncm = func_to_ncm(f);
 	struct usb_string	*us;
-	int			status;
+	int			status = 0;
 	struct usb_ep		*ep;
 	struct f_ncm_opts	*ncm_opts;
 
@@ -1433,22 +1455,17 @@
 		f->os_desc_table[0].os_desc = &ncm_opts->ncm_os_desc;
 	}
 
-	/*
-	 * in drivers/usb/gadget/configfs.c:configfs_composite_bind()
-	 * configurations are bound in sequence with list_for_each_entry,
-	 * in each configuration its functions are bound in sequence
-	 * with list_for_each_entry, so we assume no race condition
-	 * with regard to ncm_opts->bound access
-	 */
-	if (!ncm_opts->bound) {
-		mutex_lock(&ncm_opts->lock);
-		gether_set_gadget(ncm_opts->net, cdev->gadget);
+	mutex_lock(&ncm_opts->lock);
+	gether_set_gadget(ncm_opts->net, cdev->gadget);
+	if (!ncm_opts->bound)
 		status = gether_register_netdev(ncm_opts->net);
-		mutex_unlock(&ncm_opts->lock);
-		if (status)
-			goto fail;
-		ncm_opts->bound = true;
-	}
+	mutex_unlock(&ncm_opts->lock);
+
+	if (status)
+		goto fail;
+
+	ncm_opts->bound = true;
+
 	us = usb_gstrings_attach(cdev, ncm_strings,
 				 ARRAY_SIZE(ncm_string_defs));
 	if (IS_ERR(us)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_printer.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_printer.c
@@ -89,7 +89,7 @@
 	u8			printer_cdev_open;
 	wait_queue_head_t	wait;
 	unsigned		q_len;
-	char			*pnp_string;	/* We don't own memory! */
+	char			**pnp_string;	/* We don't own memory! */
 	struct usb_function	function;
 };
 
@@ -210,6 +210,7 @@
 					struct usb_endpoint_descriptor *ss)
 {
 	switch (gadget->speed) {
+	case USB_SPEED_SUPER_PLUS:
 	case USB_SPEED_SUPER:
 		return ss;
 	case USB_SPEED_HIGH:
@@ -447,11 +448,8 @@
 	mutex_lock(&dev->lock_printer_io);
 	spin_lock_irqsave(&dev->lock, flags);
 
-	if (dev->interface < 0) {
-		spin_unlock_irqrestore(&dev->lock, flags);
-		mutex_unlock(&dev->lock_printer_io);
-		return -ENODEV;
-	}
+	if (dev->interface < 0)
+		goto out_disabled;
 
 	/* We will use this flag later to check if a printer reset happened
 	 * after we turn interrupts back on.
@@ -459,6 +457,9 @@
 	dev->reset_printer = 0;
 
 	setup_rx_reqs(dev);
+	/* this dropped the lock - need to retest */
+	if (dev->interface < 0)
+		goto out_disabled;
 
 	bytes_copied = 0;
 	current_rx_req = dev->current_rx_req;
@@ -492,6 +493,8 @@
 		wait_event_interruptible(dev->rx_wait,
 				(likely(!list_empty(&dev->rx_buffers))));
 		spin_lock_irqsave(&dev->lock, flags);
+		if (dev->interface < 0)
+			goto out_disabled;
 	}
 
 	/* We have data to return then copy it to the caller's buffer.*/
@@ -535,6 +538,9 @@
 			return -EAGAIN;
 		}
 
+		if (dev->interface < 0)
+			goto out_disabled;
+
 		/* If we not returning all the data left in this RX request
 		 * buffer then adjust the amount of data left in the buffer.
 		 * Othewise if we are done with this RX request buffer then
@@ -564,6 +570,11 @@
 		return bytes_copied;
 	else
 		return -EAGAIN;
+
+out_disabled:
+	spin_unlock_irqrestore(&dev->lock, flags);
+	mutex_unlock(&dev->lock_printer_io);
+	return -ENODEV;
 }
 
 static ssize_t
@@ -584,11 +595,8 @@
 	mutex_lock(&dev->lock_printer_io);
 	spin_lock_irqsave(&dev->lock, flags);
 
-	if (dev->interface < 0) {
-		spin_unlock_irqrestore(&dev->lock, flags);
-		mutex_unlock(&dev->lock_printer_io);
-		return -ENODEV;
-	}
+	if (dev->interface < 0)
+		goto out_disabled;
 
 	/* Check if a printer reset happens while we have interrupts on */
 	dev->reset_printer = 0;
@@ -611,6 +619,8 @@
 		wait_event_interruptible(dev->tx_wait,
 				(likely(!list_empty(&dev->tx_reqs))));
 		spin_lock_irqsave(&dev->lock, flags);
+		if (dev->interface < 0)
+			goto out_disabled;
 	}
 
 	while (likely(!list_empty(&dev->tx_reqs)) && len) {
@@ -660,6 +670,9 @@
 			return -EAGAIN;
 		}
 
+		if (dev->interface < 0)
+			goto out_disabled;
+
 		list_add(&req->list, &dev->tx_reqs_active);
 
 		/* here, we unlock, and only unlock, to avoid deadlock. */
@@ -672,6 +685,8 @@
 			mutex_unlock(&dev->lock_printer_io);
 			return -EAGAIN;
 		}
+		if (dev->interface < 0)
+			goto out_disabled;
 	}
 
 	spin_unlock_irqrestore(&dev->lock, flags);
@@ -683,6 +698,11 @@
 		return bytes_copied;
 	else
 		return -EAGAIN;
+
+out_disabled:
+	spin_unlock_irqrestore(&dev->lock, flags);
+	mutex_unlock(&dev->lock_printer_io);
+	return -ENODEV;
 }
 
 static int
@@ -1000,16 +1020,16 @@
 			if ((wIndex>>8) != dev->interface)
 				break;
 
-			if (!dev->pnp_string) {
+			if (!*dev->pnp_string) {
 				value = 0;
 				break;
 			}
-			value = strlen(dev->pnp_string);
+			value = strlen(*dev->pnp_string);
 			buf[0] = (value >> 8) & 0xFF;
 			buf[1] = value & 0xFF;
-			memcpy(buf + 2, dev->pnp_string, value);
+			memcpy(buf + 2, *dev->pnp_string, value);
 			DBG(dev, "1284 PNP String: %x %s\n", value,
-			    dev->pnp_string);
+			    *dev->pnp_string);
 			break;
 
 		case GET_PORT_STATUS: /* Get Port Status */
@@ -1475,7 +1495,7 @@
 	kref_init(&dev->kref);
 	++opts->refcnt;
 	dev->minor = opts->minor;
-	dev->pnp_string = opts->pnp_string;
+	dev->pnp_string = &opts->pnp_string;
 	dev->q_len = opts->q_len;
 	mutex_unlock(&opts->lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_sourcesink.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_sourcesink.c
@@ -584,6 +584,7 @@
 
 	if (is_iso) {
 		switch (speed) {
+		case USB_SPEED_SUPER_PLUS:
 		case USB_SPEED_SUPER:
 			size = ss->isoc_maxpacket *
 					(ss->isoc_mult + 1) *
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_tcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_tcm.c
@@ -43,14 +43,17 @@
 
 /* Start bot.c code */
 
+static struct usbg_cdb *acquire_cmd_request(struct f_uas *fu);
+static void release_cmd_request(struct f_uas *fu, struct usb_request *req);
 static int bot_enqueue_cmd_cbw(struct f_uas *fu)
 {
 	int ret;
+	struct usbg_cdb *cmd = acquire_cmd_request(fu);
 
 	if (fu->flags & USBG_BOT_CMD_PEND)
 		return 0;
 
-	ret = usb_ep_queue(fu->ep_out, fu->cmd.req, GFP_ATOMIC);
+	ret = usb_ep_queue(fu->ep_out, cmd->req, GFP_ATOMIC);
 	if (!ret)
 		fu->flags |= USBG_BOT_CMD_PEND;
 	return ret;
@@ -61,6 +64,7 @@
 	struct usbg_cmd *cmd = req->context;
 	struct f_uas *fu = cmd->fu;
 
+	release_cmd_request(fu, req);
 	transport_generic_free_cmd(&cmd->se_cmd, 0);
 	if (req->status < 0) {
 		pr_err("ERR %s(%d)\n", __func__, __LINE__);
@@ -136,7 +140,7 @@
 		}
 		req->complete = bot_err_compl;
 		req->context = cmd;
-		req->buf = fu->cmd.buf;
+		req->buf = fu->cmd[0]->buf;
 		usb_ep_queue(ep, req, GFP_KERNEL);
 	} else {
 		bot_enqueue_sense_code(fu, cmd);
@@ -245,7 +249,6 @@
 {
 	struct f_uas *fu = cmd->fu;
 	struct se_cmd *se_cmd = &cmd->se_cmd;
-	struct usb_gadget *gadget = fuas_to_gadget(fu);
 	int ret;
 
 	init_completion(&cmd->write_complete);
@@ -256,22 +259,6 @@
 		return -EINVAL;
 	}
 
-	if (!gadget->sg_supported) {
-		cmd->data_buf = kmalloc(se_cmd->data_length, GFP_KERNEL);
-		if (!cmd->data_buf)
-			return -ENOMEM;
-
-		fu->bot_req_out->buf = cmd->data_buf;
-	} else {
-		fu->bot_req_out->buf = NULL;
-		fu->bot_req_out->num_sgs = se_cmd->t_data_nents;
-		fu->bot_req_out->sg = se_cmd->t_data_sg;
-	}
-
-	fu->bot_req_out->complete = usbg_data_write_cmpl;
-	fu->bot_req_out->length = se_cmd->data_length;
-	fu->bot_req_out->context = cmd;
-
 	ret = usbg_prepare_w_request(cmd, fu->bot_req_out);
 	if (ret)
 		goto cleanup;
@@ -297,11 +284,84 @@
 	if (req->status < 0)
 		return;
 
+	release_cmd_request(fu, req);
 	ret = bot_submit_command(fu, req->buf, req->actual);
 	if (ret)
 		pr_err("%s(%d): %d\n", __func__, __LINE__, ret);
 }
 
+static struct usbg_cdb *acquire_cmd_request(struct f_uas *fu)
+{
+	int i;
+
+	for (i = 0; i < fu->ncmd; i++) {
+		if (!fu->cmd[i]->claimed) {
+			fu->cmd[i]->claimed = true;
+			return fu->cmd[i];
+		}
+	}
+	return NULL;
+}
+
+static void release_cmd_request(struct f_uas *fu, struct usb_request *req)
+{
+	int i;
+
+	for (i = 0; i < fu->ncmd; i++) {
+		if (fu->cmd[i]->req == req)
+			fu->cmd[i]->claimed = false;
+	}
+}
+
+static void free_cmd_resource(struct f_uas *fu, struct usb_ep *ep)
+{
+	int i;
+
+	for (i = 0; i < fu->ncmd; i++) {
+		if (fu->cmd[i]->req)
+			usb_ep_free_request(ep, fu->cmd[i]->req);
+
+		kfree(fu->cmd[i]->buf);
+		fu->cmd[i]->buf = NULL;
+
+		kfree(fu->cmd[i]);
+		fu->cmd[i] = NULL;
+	}
+}
+
+static int alloc_cmd_resource(struct f_uas *fu, int num, struct usb_ep *ep,
+			      void  (*complete)(struct usb_ep *ep,
+						struct usb_request *req))
+{
+	int i;
+
+	fu->ncmd = num;
+	for (i = 0; i < fu->ncmd; i++) {
+		fu->cmd[i] = kcalloc(fu->ncmd, sizeof(struct usbg_cdb),
+				GFP_KERNEL);
+		if (!fu->cmd[i])
+			goto err_cmd;
+
+		fu->cmd[i]->req = usb_ep_alloc_request(ep, GFP_KERNEL);
+		if (!fu->cmd[i]->req)
+			goto err_cmd;
+
+		fu->cmd[i]->buf = kmalloc(fu->ep_out->maxpacket, GFP_KERNEL);
+		if (!fu->cmd[i]->buf)
+			goto err_cmd;
+
+		fu->cmd[i]->req->complete = complete;
+		fu->cmd[i]->req->buf = fu->cmd[i]->buf;
+		fu->cmd[i]->req->length = fu->ep_out->maxpacket;
+		fu->cmd[i]->req->context = fu;
+	}
+
+	return 0;
+err_cmd:
+	free_cmd_resource(fu, ep);
+	return -ENOMEM;
+}
+
 static int bot_prepare_reqs(struct f_uas *fu)
 {
 	int ret;
@@ -314,10 +374,6 @@
 	if (!fu->bot_req_out)
 		goto err_out;
 
-	fu->cmd.req = usb_ep_alloc_request(fu->ep_out, GFP_KERNEL);
-	if (!fu->cmd.req)
-		goto err_cmd;
-
 	fu->bot_status.req = usb_ep_alloc_request(fu->ep_in, GFP_KERNEL);
 	if (!fu->bot_status.req)
 		goto err_sts;
@@ -327,28 +383,20 @@
 	fu->bot_status.req->complete = bot_status_complete;
 	fu->bot_status.csw.Signature = cpu_to_le32(US_BULK_CS_SIGN);
 
-	fu->cmd.buf = kmalloc(fu->ep_out->maxpacket, GFP_KERNEL);
-	if (!fu->cmd.buf)
-		goto err_buf;
-
-	fu->cmd.req->complete = bot_cmd_complete;
-	fu->cmd.req->buf = fu->cmd.buf;
-	fu->cmd.req->length = fu->ep_out->maxpacket;
-	fu->cmd.req->context = fu;
+	ret = alloc_cmd_resource(fu, BOT_MAX_COMMANDS, fu->ep_out,
+				 bot_cmd_complete);
+	if (ret)
+		goto err_cmd;
 
 	ret = bot_enqueue_cmd_cbw(fu);
 	if (ret)
 		goto err_queue;
 	return 0;
 err_queue:
-	kfree(fu->cmd.buf);
-	fu->cmd.buf = NULL;
-err_buf:
+	free_cmd_resource(fu, fu->ep_out);
+err_cmd:
 	usb_ep_free_request(fu->ep_in, fu->bot_status.req);
 err_sts:
-	usb_ep_free_request(fu->ep_out, fu->cmd.req);
-	fu->cmd.req = NULL;
-err_cmd:
 	usb_ep_free_request(fu->ep_out, fu->bot_req_out);
 	fu->bot_req_out = NULL;
 err_out:
@@ -372,16 +420,13 @@
 
 	usb_ep_free_request(fu->ep_in, fu->bot_req_in);
 	usb_ep_free_request(fu->ep_out, fu->bot_req_out);
-	usb_ep_free_request(fu->ep_out, fu->cmd.req);
 	usb_ep_free_request(fu->ep_in, fu->bot_status.req);
 
-	kfree(fu->cmd.buf);
+	free_cmd_resource(fu, fu->ep_out);
 
 	fu->bot_req_in = NULL;
 	fu->bot_req_out = NULL;
-	fu->cmd.req = NULL;
 	fu->bot_status.req = NULL;
-	fu->cmd.buf = NULL;
 }
 
 static void bot_set_alt(struct f_uas *fu)
@@ -480,14 +525,6 @@
 	stream->req_status = NULL;
 }
 
-static void uasp_free_cmdreq(struct f_uas *fu)
-{
-	usb_ep_free_request(fu->ep_cmd, fu->cmd.req);
-	kfree(fu->cmd.buf);
-	fu->cmd.req = NULL;
-	fu->cmd.buf = NULL;
-}
-
 static void uasp_cleanup_old_alt(struct f_uas *fu)
 {
 	int i;
@@ -502,7 +539,7 @@
 
 	for (i = 0; i < UASP_SS_EP_COMP_NUM_STREAMS; i++)
 		uasp_cleanup_one_stream(fu, &fu->stream[i]);
-	uasp_free_cmdreq(fu);
+	free_cmd_resource(fu, fu->ep_cmd);
 }
 
 static void uasp_status_data_cmpl(struct usb_ep *ep, struct usb_request *req);
@@ -567,6 +604,7 @@
 	struct usbg_cmd *cmd = req->context;
 	struct uas_stream *stream = cmd->stream;
 	struct f_uas *fu = cmd->fu;
+	struct usbg_cdb *cmd_cdb;
 	int ret;
 
 	if (req->status < 0)
@@ -601,7 +639,8 @@
 
 	case UASP_QUEUE_COMMAND:
 		transport_generic_free_cmd(&cmd->se_cmd, 0);
-		usb_ep_queue(fu->ep_cmd, fu->cmd.req, GFP_ATOMIC);
+		cmd_cdb = acquire_cmd_request(fu);
+		usb_ep_queue(fu->ep_cmd, cmd_cdb->req, GFP_ATOMIC);
 		break;
 
 	default:
@@ -721,11 +760,13 @@
 static void uasp_cmd_complete(struct usb_ep *ep, struct usb_request *req)
 {
 	struct f_uas *fu = req->context;
+	struct usbg_cdb *cmd;
 	int ret;
 
 	if (req->status < 0)
 		return;
 
+	release_cmd_request(fu, req);
 	ret = usbg_submit_command(fu, req->buf, req->actual);
 	/*
 	 * Once we tune for performance enqueue the command req here again so
@@ -735,7 +776,8 @@
 	 */
 	if (!ret)
 		return;
-	usb_ep_queue(fu->ep_cmd, fu->cmd.req, GFP_ATOMIC);
+	cmd = acquire_cmd_request(fu);
+	usb_ep_queue(fu->ep_cmd, cmd->req, GFP_ATOMIC);
 }
 
 static int uasp_alloc_stream_res(struct f_uas *fu, struct uas_stream *stream)
@@ -764,28 +806,6 @@
 	return -ENOMEM;
 }
 
-static int uasp_alloc_cmd(struct f_uas *fu)
-{
-	fu->cmd.req = usb_ep_alloc_request(fu->ep_cmd, GFP_KERNEL);
-	if (!fu->cmd.req)
-		goto err;
-
-	fu->cmd.buf = kmalloc(fu->ep_cmd->maxpacket, GFP_KERNEL);
-	if (!fu->cmd.buf)
-		goto err_buf;
-
-	fu->cmd.req->complete = uasp_cmd_complete;
-	fu->cmd.req->buf = fu->cmd.buf;
-	fu->cmd.req->length = fu->ep_cmd->maxpacket;
-	fu->cmd.req->context = fu;
-	return 0;
-
-err_buf:
-	usb_ep_free_request(fu->ep_cmd, fu->cmd.req);
-err:
-	return -ENOMEM;
-}
-
 static void uasp_setup_stream_res(struct f_uas *fu, int max_streams)
 {
 	int i;
@@ -803,12 +823,15 @@
 {
 	int ret;
 	int i;
-	int max_streams;
+	int max_streams, max_commands;
 
-	if (fu->flags & USBG_USE_STREAMS)
+	if (fu->flags & USBG_USE_STREAMS) {
+		max_commands = UASP_MAX_COMMANDS;
 		max_streams = UASP_SS_EP_COMP_NUM_STREAMS;
-	else
+	} else {
+		max_commands = 1;
 		max_streams = 1;
+	}
 
 	for (i = 0; i < max_streams; i++) {
 		ret = uasp_alloc_stream_res(fu, &fu->stream[i]);
@@ -816,19 +839,25 @@
 			goto err_cleanup;
 	}
 
-	ret = uasp_alloc_cmd(fu);
+	ret = alloc_cmd_resource(fu, max_commands, fu->ep_cmd,
+				 uasp_cmd_complete);
 	if (ret)
 		goto err_free_stream;
 	uasp_setup_stream_res(fu, max_streams);
 
-	ret = usb_ep_queue(fu->ep_cmd, fu->cmd.req, GFP_ATOMIC);
-	if (ret)
-		goto err_free_stream;
+	/* queue number of commands */
+	for (i = 0; i < fu->ncmd; i++) {
+		struct usbg_cdb *cmd = acquire_cmd_request(fu);
+
+		ret = usb_ep_queue(fu->ep_cmd, cmd->req, GFP_ATOMIC);
+		if (ret)
+			goto err_free_stream;
+	}
 
 	return 0;
 
 err_free_stream:
-	uasp_free_cmdreq(fu);
+	free_cmd_resource(fu, fu->ep_cmd);
 
 err_cleanup:
 	if (i) {
@@ -841,16 +870,28 @@
 	return ret;
 }
 
+#define SS_BOT_INTERFACE_DESC_NO	5
 static void uasp_set_alt(struct f_uas *fu)
 {
 	struct usb_function *f = &fu->function;
 	struct usb_gadget *gadget = f->config->cdev->gadget;
+	struct usb_descriptor_header    **ss_uasp_backup = f->ss_descriptors;
 	int ret;
 
 	fu->flags = USBG_IS_UAS;
 
-	if (gadget->speed >= USB_SPEED_SUPER)
+	if (gadget->speed == USB_SPEED_SUPER) {
 		fu->flags |= USBG_USE_STREAMS;
+		/* If device connect in SS then comp_descriptor with stream
+		 * should be attached to descriptor. Since BOT and UAS using
+		 * same endpoint, config_ep_by_speed will returns first match
+		 * with comp_descriptor without stream. This is just workaround
+		 * proper fix need to be introduced. Here advancing descritor
+		 * header ss_descriptors with number of descriptor present in
+		 * BOT mode.
+		 */
+		f->ss_descriptors += SS_BOT_INTERFACE_DESC_NO;
+	}
 
 	config_ep_by_speed_and_alt(gadget, f, fu->ep_in, USB_G_ALT_INT_UAS);
 	ret = usb_ep_enable(fu->ep_in);
@@ -876,6 +917,10 @@
 		goto err_wq;
 	fu->flags |= USBG_ENABLED;
 
+	/* restore ss_descriptors */
+	if (gadget->speed == USB_SPEED_SUPER)
+		f->ss_descriptors = ss_uasp_backup;
+
 	pr_info("Using the UAS protocol\n");
 	return;
 err_wq:
@@ -887,6 +932,9 @@
 err_b_out:
 	usb_ep_disable(fu->ep_in);
 err_b_in:
+	/* restore ss_descriptors */
+	if (gadget->speed == USB_SPEED_SUPER)
+		f->ss_descriptors = ss_uasp_backup;
 	fu->flags = 0;
 }
 
@@ -952,6 +1000,56 @@
 	return ret;
 }
 
+static void recover_w_length_with_maxpacket(struct usbg_cmd *cmd,
+					    struct usb_request *req)
+{
+	struct se_cmd *se_cmd = &cmd->se_cmd;
+	struct f_uas *fu = cmd->fu;
+	struct usb_gadget *gadget = fuas_to_gadget(fu);
+	int rem;
+
+	rem = se_cmd->data_length % fu->ep_out->maxpacket;
+	if (rem) {
+		/* recover paded data length */
+		cmd->data_len -= fu->ep_out->maxpacket - rem;
+
+		if (gadget->sg_supported) {
+			struct scatterlist *s = sg_last(se_cmd->t_data_sg,
+					se_cmd->t_data_nents);
+
+			s->length -= fu->ep_out->maxpacket - rem;
+		}
+	}
+}
+
+static void adjust_w_length_with_maxpacket(struct usbg_cmd *cmd,
+					   struct usb_request *req)
+{
+	struct se_cmd *se_cmd = &cmd->se_cmd;
+	struct f_uas *fu = cmd->fu;
+	struct usb_gadget *gadget = fuas_to_gadget(fu);
+	int rem;
+
+	cmd->data_len = se_cmd->data_length;
+	rem = cmd->data_len % fu->ep_out->maxpacket;
+	if (rem) {
+		/* pad data length so that transfer size can be in multiple of
+		 * max packet size
+		 */
+		cmd->data_len += fu->ep_out->maxpacket - rem;
+
+		if (gadget->sg_supported) {
+			/* if sg is supported and data length in page also need
+			 * to be adjusted as multiple of max packet size.
+			 */
+			struct scatterlist *s = sg_last(se_cmd->t_data_sg,
+					se_cmd->t_data_nents);
+
+			s->length += fu->ep_out->maxpacket - rem;
+		}
+	}
+}
+
 static void usbg_data_write_cmpl(struct usb_ep *ep, struct usb_request *req)
 {
 	struct usbg_cmd *cmd = req->context;
@@ -962,6 +1060,8 @@
 		goto cleanup;
 	}
 
+	recover_w_length_with_maxpacket(cmd, req);
+
 	if (req->num_sgs == 0) {
 		sg_copy_from_buffer(se_cmd->t_data_sg,
 				se_cmd->t_data_nents,
@@ -973,6 +1073,7 @@
 	return;
 
 cleanup:
+	target_put_sess_cmd(se_cmd);
 	transport_generic_free_cmd(&cmd->se_cmd, 0);
 }
 
@@ -982,8 +1083,10 @@
 	struct f_uas *fu = cmd->fu;
 	struct usb_gadget *gadget = fuas_to_gadget(fu);
 
+	adjust_w_length_with_maxpacket(cmd, req);
+
 	if (!gadget->sg_supported) {
-		cmd->data_buf = kmalloc(se_cmd->data_length, GFP_ATOMIC);
+		cmd->data_buf = kmalloc(cmd->data_len, GFP_ATOMIC);
 		if (!cmd->data_buf)
 			return -ENOMEM;
 
@@ -996,7 +1099,7 @@
 
 	req->is_last = 1;
 	req->complete = usbg_data_write_cmpl;
-	req->length = se_cmd->data_length;
+	req->length = cmd->data_len;
 	req->context = cmd;
 	return 0;
 }
@@ -1065,8 +1168,7 @@
 
 out:
 	transport_send_check_condition_and_sense(se_cmd,
-			TCM_UNSUPPORTED_SCSI_OPCODE, 1);
-	transport_generic_free_cmd(&cmd->se_cmd, 0);
+			TCM_UNSUPPORTED_SCSI_OPCODE, 0);
 }
 
 static struct usbg_cmd *usbg_get_cmd(struct f_uas *fu,
@@ -1189,13 +1291,13 @@
 
 	target_submit_cmd(se_cmd, tv_nexus->tvn_se_sess,
 			  cmd->cmd_buf, cmd->sense_iu.sense, cmd->unpacked_lun,
-			  cmd->data_len, cmd->prio_attr, dir, 0);
+			  cmd->data_len, cmd->prio_attr, dir,
+			  TARGET_SCF_ACK_KREF);
 	return;
 
 out:
 	transport_send_check_condition_and_sense(se_cmd,
-				TCM_UNSUPPORTED_SCSI_OPCODE, 1);
-	transport_generic_free_cmd(&cmd->se_cmd, 0);
+				TCM_UNSUPPORTED_SCSI_OPCODE, 0);
 }
 
 static int bot_submit_command(struct f_uas *fu,
@@ -1676,9 +1778,11 @@
 CONFIGFS_ATTR(tcm_usbg_tpg_, enable);
 CONFIGFS_ATTR(tcm_usbg_tpg_, nexus);
 
+static struct configfs_attribute tcm_usbg_tpg_attr_maxburst;
 static struct configfs_attribute *usbg_base_attrs[] = {
 	&tcm_usbg_tpg_attr_enable,
 	&tcm_usbg_tpg_attr_nexus,
+	&tcm_usbg_tpg_attr_maxburst,
 	NULL,
 };
 
@@ -1986,6 +2090,32 @@
 	NULL,
 };
 
+static ssize_t tcm_usbg_tpg_maxburst_show(struct config_item *item, char *page)
+{
+	return snprintf(page, PAGE_SIZE, "%u\n", uasp_cmd_comp_desc.bMaxBurst);
+}
+
+static ssize_t tcm_usbg_tpg_maxburst_store(struct config_item *item,
+					   const char *page, size_t count)
+{
+	int value;
+	int ret;
+
+	ret = kstrtouint(page, 10, &value);
+	if (ret)
+		return ret;
+
+	uasp_bi_ep_comp_desc.bMaxBurst = value;
+	uasp_bo_ep_comp_desc.bMaxBurst = value;
+	uasp_status_in_ep_comp_desc.bMaxBurst = value;
+	uasp_cmd_comp_desc.bMaxBurst = value;
+	bot_bi_ep_comp_desc.bMaxBurst = value;
+	bot_bo_ep_comp_desc.bMaxBurst = value;
+
+	return count;
+}
+CONFIGFS_ATTR(tcm_usbg_tpg_, maxburst);
+
 static int tcm_bind(struct usb_configuration *c, struct usb_function *f)
 {
 	struct f_uas		*fu = to_f_uas(f);
@@ -2018,43 +2148,39 @@
 	bot_intf_desc.bInterfaceNumber = iface;
 	uasp_intf_desc.bInterfaceNumber = iface;
 	fu->iface = iface;
-	ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_bi_desc,
-			&uasp_bi_ep_comp_desc);
+	ep = usb_ep_autoconfig(gadget, &uasp_fs_bi_desc);
 	if (!ep)
 		goto ep_fail;
 
 	fu->ep_in = ep;
 
-	ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_bo_desc,
-			&uasp_bo_ep_comp_desc);
+	ep = usb_ep_autoconfig(gadget, &uasp_fs_bo_desc);
 	if (!ep)
 		goto ep_fail;
 	fu->ep_out = ep;
 
-	ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_status_desc,
-			&uasp_status_in_ep_comp_desc);
+	ep = usb_ep_autoconfig(gadget, &uasp_fs_status_desc);
 	if (!ep)
 		goto ep_fail;
 	fu->ep_status = ep;
 
-	ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_cmd_desc,
-			&uasp_cmd_comp_desc);
+	ep = usb_ep_autoconfig(gadget, &uasp_fs_cmd_desc);
 	if (!ep)
 		goto ep_fail;
 	fu->ep_cmd = ep;
 
 	/* Assume endpoint addresses are the same for both speeds */
-	uasp_bi_desc.bEndpointAddress =	uasp_ss_bi_desc.bEndpointAddress;
-	uasp_bo_desc.bEndpointAddress = uasp_ss_bo_desc.bEndpointAddress;
+	uasp_bi_desc.bEndpointAddress =	uasp_fs_bi_desc.bEndpointAddress;
+	uasp_bo_desc.bEndpointAddress = uasp_fs_bo_desc.bEndpointAddress;
 	uasp_status_desc.bEndpointAddress =
-		uasp_ss_status_desc.bEndpointAddress;
-	uasp_cmd_desc.bEndpointAddress = uasp_ss_cmd_desc.bEndpointAddress;
+		uasp_fs_status_desc.bEndpointAddress;
+	uasp_cmd_desc.bEndpointAddress = uasp_fs_cmd_desc.bEndpointAddress;
 
-	uasp_fs_bi_desc.bEndpointAddress = uasp_ss_bi_desc.bEndpointAddress;
-	uasp_fs_bo_desc.bEndpointAddress = uasp_ss_bo_desc.bEndpointAddress;
-	uasp_fs_status_desc.bEndpointAddress =
-		uasp_ss_status_desc.bEndpointAddress;
-	uasp_fs_cmd_desc.bEndpointAddress = uasp_ss_cmd_desc.bEndpointAddress;
+	uasp_ss_bi_desc.bEndpointAddress = uasp_fs_bi_desc.bEndpointAddress;
+	uasp_ss_bo_desc.bEndpointAddress = uasp_fs_bo_desc.bEndpointAddress;
+	uasp_ss_status_desc.bEndpointAddress =
+		uasp_fs_status_desc.bEndpointAddress;
+	uasp_ss_cmd_desc.bEndpointAddress = uasp_fs_cmd_desc.bEndpointAddress;
 
 	ret = usb_assign_descriptors(f, uasp_fs_function_desc,
 			uasp_hs_function_desc, uasp_ss_function_desc,
@@ -2098,9 +2224,14 @@
 
 static int tcm_get_alt(struct usb_function *f, unsigned intf)
 {
-	if (intf == bot_intf_desc.bInterfaceNumber)
+	struct f_uas *fu = to_f_uas(f);
+
+	if (fu->iface != intf)
+		return -EOPNOTSUPP;
+
+	if (fu->flags & USBG_IS_BOT)
 		return USB_G_ALT_INT_BBB;
-	if (intf == uasp_intf_desc.bInterfaceNumber)
+	else if (fu->flags & USBG_IS_UAS)
 		return USB_G_ALT_INT_UAS;
 
 	return -EOPNOTSUPP;
@@ -2110,6 +2241,9 @@
 {
 	struct f_uas *fu = to_f_uas(f);
 
+	if (fu->iface != intf)
+		return -EOPNOTSUPP;
+
 	if ((alt == USB_G_ALT_INT_BBB) || (alt == USB_G_ALT_INT_UAS)) {
 		struct guas_setup_wq *work;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_uac2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_uac2.c
@@ -202,7 +202,7 @@
 
 	.bDescriptorSubtype = UAC_INPUT_TERMINAL,
 	/* .bTerminalID = DYNAMIC */
-	.wTerminalType = cpu_to_le16(UAC_INPUT_TERMINAL_UNDEFINED),
+	.wTerminalType = cpu_to_le16(UAC_INPUT_TERMINAL_MICROPHONE),
 	.bAssocTerminal = 0,
 	/* .bCSourceID = DYNAMIC */
 	.iChannelNames = 0,
@@ -230,7 +230,7 @@
 
 	.bDescriptorSubtype = UAC_OUTPUT_TERMINAL,
 	/* .bTerminalID = DYNAMIC */
-	.wTerminalType = cpu_to_le16(UAC_OUTPUT_TERMINAL_UNDEFINED),
+	.wTerminalType = cpu_to_le16(UAC_OUTPUT_TERMINAL_SPEAKER),
 	.bAssocTerminal = 0,
 	/* .bSourceID = DYNAMIC */
 	/* .bCSourceID = DYNAMIC */
@@ -281,6 +281,12 @@
 	.bInterval = 4,
 };
 
+static struct usb_ss_ep_comp_descriptor ss_ep_int_desc_comp = {
+	.bLength = sizeof(ss_ep_int_desc_comp),
+	.bDescriptorType = USB_DT_SS_ENDPOINT_COMP,
+	.wBytesPerInterval = cpu_to_le16(6),
+};
+
 /* Audio Streaming OUT Interface - Alt0 */
 static struct usb_interface_descriptor std_as_out_if0_desc = {
 	.bLength = sizeof std_as_out_if0_desc,
@@ -594,7 +600,8 @@
 	(struct usb_descriptor_header *)&in_feature_unit_desc,
 	(struct usb_descriptor_header *)&io_out_ot_desc,
 
-  (struct usb_descriptor_header *)&ss_ep_int_desc,
+	(struct usb_descriptor_header *)&ss_ep_int_desc,
+	(struct usb_descriptor_header *)&ss_ep_int_desc_comp,
 
 	(struct usb_descriptor_header *)&std_as_out_if0_desc,
 	(struct usb_descriptor_header *)&std_as_out_if1_desc,
@@ -721,6 +728,7 @@
 	struct usb_ss_ep_comp_descriptor *epout_desc_comp = NULL;
 	struct usb_ss_ep_comp_descriptor *epin_desc_comp = NULL;
 	struct usb_ss_ep_comp_descriptor *epin_fback_desc_comp = NULL;
+	struct usb_ss_ep_comp_descriptor *ep_int_desc_comp = NULL;
 	struct usb_endpoint_descriptor *epout_desc;
 	struct usb_endpoint_descriptor *epin_desc;
 	struct usb_endpoint_descriptor *epin_fback_desc;
@@ -748,6 +756,7 @@
 		epin_fback_desc = &ss_epin_fback_desc;
 		epin_fback_desc_comp = &ss_epin_fback_desc_comp;
 		ep_int_desc = &ss_ep_int_desc;
+		ep_int_desc_comp = &ss_ep_int_desc_comp;
 	}
 
 	i = 0;
@@ -760,15 +769,15 @@
 		headers[i++] = USBDHDR(&out_clk_src_desc);
 		headers[i++] = USBDHDR(&usb_out_it_desc);
 
-    if (FUOUT_EN(opts))
-      headers[i++] = USBDHDR(out_feature_unit_desc);
-  }
+		if (FUOUT_EN(opts))
+			headers[i++] = USBDHDR(out_feature_unit_desc);
+	}
 
 	if (EPIN_EN(opts)) {
 		headers[i++] = USBDHDR(&io_in_it_desc);
 
-    if (FUIN_EN(opts))
-      headers[i++] = USBDHDR(in_feature_unit_desc);
+		if (FUIN_EN(opts))
+			headers[i++] = USBDHDR(in_feature_unit_desc);
 
 		headers[i++] = USBDHDR(&usb_in_ot_desc);
 	}
@@ -776,10 +785,13 @@
 	if (EPOUT_EN(opts))
 		headers[i++] = USBDHDR(&io_out_ot_desc);
 
-  if (FUOUT_EN(opts) || FUIN_EN(opts))
-      headers[i++] = USBDHDR(ep_int_desc);
+	if (FUOUT_EN(opts) || FUIN_EN(opts)) {
+		headers[i++] = USBDHDR(ep_int_desc);
+		if (ep_int_desc_comp)
+			headers[i++] = USBDHDR(ep_int_desc_comp);
+	}
 
-  if (EPOUT_EN(opts)) {
+	if (EPOUT_EN(opts)) {
 		headers[i++] = USBDHDR(&std_as_out_if0_desc);
 		headers[i++] = USBDHDR(&std_as_out_if1_desc);
 		headers[i++] = USBDHDR(&as_out_hdr_desc);
@@ -1057,6 +1069,7 @@
 		}
 		std_as_out_if0_desc.bInterfaceNumber = ret;
 		std_as_out_if1_desc.bInterfaceNumber = ret;
+		std_as_out_if1_desc.bNumEndpoints = 1;
 		uac2->as_out_intf = ret;
 		uac2->as_out_alt = 0;
 
@@ -1090,6 +1103,7 @@
 		uac2->as_in_alt = 0;
 	}
 
+	std_ac_if_desc.bNumEndpoints = 0;
 	if (FUOUT_EN(uac2_opts) || FUIN_EN(uac2_opts)) {
 		uac2->int_ep = usb_ep_autoconfig(gadget, &fs_ep_int_desc);
 		if (!uac2->int_ep) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/f_uvc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/f_uvc.c
@@ -213,8 +213,9 @@
 
 		memset(&v4l2_event, 0, sizeof(v4l2_event));
 		v4l2_event.type = UVC_EVENT_DATA;
-		uvc_event->data.length = req->actual;
-		memcpy(&uvc_event->data.data, req->buf, req->actual);
+		uvc_event->data.length = min_t(unsigned int, req->actual,
+			sizeof(uvc_event->data.data));
+		memcpy(&uvc_event->data.data, req->buf, uvc_event->data.length);
 		v4l2_event_queue(&uvc->vdev, &v4l2_event);
 	}
 }
@@ -884,17 +885,42 @@
 	kfree(uvc);
 }
 
-static void uvc_unbind(struct usb_configuration *c, struct usb_function *f)
+static void uvc_function_unbind(struct usb_configuration *c,
+				struct usb_function *f)
 {
 	struct usb_composite_dev *cdev = c->cdev;
 	struct uvc_device *uvc = to_uvc(f);
+	long wait_ret = 1;
 
-	uvcg_info(f, "%s\n", __func__);
+	uvcg_info(f, "%s()\n", __func__);
+
+	/* If we know we're connected via v4l2, then there should be a cleanup
+	 * of the device from userspace either via UVC_EVENT_DISCONNECT or
+	 * though the video device removal uevent. Allow some time for the
+	 * application to close out before things get deleted.
+	 */
+	if (uvc->func_connected) {
+		uvcg_dbg(f, "waiting for clean disconnect\n");
+		wait_ret = wait_event_interruptible_timeout(uvc->func_connected_queue,
+				uvc->func_connected == false, msecs_to_jiffies(500));
+		uvcg_dbg(f, "done waiting with ret: %ld\n", wait_ret);
+	}
 
 	device_remove_file(&uvc->vdev.dev, &dev_attr_function_name);
 	video_unregister_device(&uvc->vdev);
 	v4l2_device_unregister(&uvc->v4l2_dev);
 
+	if (uvc->func_connected) {
+		/* Wait for the release to occur to ensure there are no longer any
+		 * pending operations that may cause panics when resources are cleaned
+		 * up.
+		 */
+		uvcg_warn(f, "%s no clean disconnect, wait for release\n", __func__);
+		wait_ret = wait_event_interruptible_timeout(uvc->func_connected_queue,
+				uvc->func_connected == false, msecs_to_jiffies(1000));
+		uvcg_dbg(f, "done waiting for release with ret: %ld\n", wait_ret);
+	}
+
 	usb_ep_free_request(cdev->gadget->ep0, uvc->control_req);
 	kfree(uvc->control_buf);
 
@@ -913,6 +939,7 @@
 
 	mutex_init(&uvc->video.mutex);
 	uvc->state = UVC_STATE_DISCONNECTED;
+	init_waitqueue_head(&uvc->func_connected_queue);
 	opts = fi_to_f_uvc_opts(fi);
 
 	mutex_lock(&opts->lock);
@@ -943,7 +970,7 @@
 	/* Register the function. */
 	uvc->func.name = "uvc";
 	uvc->func.bind = uvc_function_bind;
-	uvc->func.unbind = uvc_unbind;
+	uvc->func.unbind = uvc_function_unbind;
 	uvc->func.get_alt = uvc_function_get_alt;
 	uvc->func.set_alt = uvc_function_set_alt;
 	uvc->func.disable = uvc_function_disable;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/rndis.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/rndis.c
@@ -637,14 +637,18 @@
 	rndis_set_cmplt_type *resp;
 	rndis_resp_t *r;
 
+	BufLength = le32_to_cpu(buf->InformationBufferLength);
+	BufOffset = le32_to_cpu(buf->InformationBufferOffset);
+	if ((BufLength > RNDIS_MAX_TOTAL_SIZE) ||
+	    (BufOffset > RNDIS_MAX_TOTAL_SIZE) ||
+	    (BufOffset + 8 >= RNDIS_MAX_TOTAL_SIZE))
+		    return -EINVAL;
+
 	r = rndis_add_response(params, sizeof(rndis_set_cmplt_type));
 	if (!r)
 		return -ENOMEM;
 	resp = (rndis_set_cmplt_type *)r->buf;
 
-	BufLength = le32_to_cpu(buf->InformationBufferLength);
-	BufOffset = le32_to_cpu(buf->InformationBufferOffset);
-
 #ifdef	VERBOSE_DEBUG
 	pr_debug("%s: Length: %d\n", __func__, BufLength);
 	pr_debug("%s: Offset: %d\n", __func__, BufOffset);
@@ -919,6 +923,7 @@
 	params->resp_avail = resp_avail;
 	params->v = v;
 	INIT_LIST_HEAD(&params->resp_queue);
+	spin_lock_init(&params->resp_lock);
 	pr_debug("%s: configNr = %d\n", __func__, i);
 
 	return params;
@@ -1012,12 +1017,14 @@
 {
 	rndis_resp_t *r, *n;
 
+	spin_lock(&params->resp_lock);
 	list_for_each_entry_safe(r, n, &params->resp_queue, list) {
 		if (r->buf == buf) {
 			list_del(&r->list);
 			kfree(r);
 		}
 	}
+	spin_unlock(&params->resp_lock);
 }
 EXPORT_SYMBOL_GPL(rndis_free_response);
 
@@ -1027,14 +1034,17 @@
 
 	if (!length) return NULL;
 
+	spin_lock(&params->resp_lock);
 	list_for_each_entry_safe(r, n, &params->resp_queue, list) {
 		if (!r->send) {
 			r->send = 1;
 			*length = r->length;
+			spin_unlock(&params->resp_lock);
 			return r->buf;
 		}
 	}
 
+	spin_unlock(&params->resp_lock);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(rndis_get_next_response);
@@ -1051,7 +1061,9 @@
 	r->length = length;
 	r->send = 0;
 
+	spin_lock(&params->resp_lock);
 	list_add_tail(&r->list, &params->resp_queue);
+	spin_unlock(&params->resp_lock);
 	return r;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/rndis.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/rndis.h
@@ -174,6 +174,7 @@
 	void			(*resp_avail)(void *v);
 	void			*v;
 	struct list_head	resp_queue;
+	spinlock_t		resp_lock;
 } rndis_params;
 
 /* RNDIS Message parser and other useless functions */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/storage_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/storage_common.c
@@ -294,8 +294,10 @@
 void store_cdrom_address(u8 *dest, int msf, u32 addr)
 {
 	if (msf) {
-		/* Convert to Minutes-Seconds-Frames */
-		addr >>= 2;		/* Convert to 2048-byte frames */
+		/*
+		 * Convert to Minutes-Seconds-Frames.
+		 * Sector size is already set to 2048 bytes.
+		 */
 		addr += 2*75;		/* Lead-in occupies 2 seconds */
 		dest[3] = addr % 75;	/* Frames */
 		addr /= 75;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/tcm.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/tcm.h
@@ -98,6 +98,7 @@
 struct usbg_cdb {
 	struct usb_request	*req;
 	void			*buf;
+	bool			claimed;
 };
 
 struct bot_status {
@@ -105,6 +106,9 @@
 	struct bulk_cs_wrap	csw;
 };
 
+#define UASP_MAX_COMMANDS	6
+#define BOT_MAX_COMMANDS	1
+#define MAX_COMMANDS		UASP_MAX_COMMANDS
 struct f_uas {
 	struct usbg_tpg		*tpg;
 	struct usb_function	function;
@@ -117,7 +121,8 @@
 #define USBG_IS_BOT		(1 << 3)
 #define USBG_BOT_CMD_PEND	(1 << 4)
 
-	struct usbg_cdb		cmd;
+	u32			ncmd;
+	struct usbg_cdb		*cmd[MAX_COMMANDS];
 	struct usb_ep		*ep_in;
 	struct usb_ep		*ep_out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/u_audio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/u_audio.c
@@ -474,15 +474,24 @@
 	struct usb_ep *ep, *ep_fback;
 	struct uac_rtd_params *prm;
 	struct uac_params *params = &audio_dev->params;
-	int req_len, i;
+	int req_len, i, ret;
 
 	ep = audio_dev->out_ep;
 	prm = &uac->c_prm;
-	config_ep_by_speed(gadget, &audio_dev->func, ep);
+	ret = config_ep_by_speed(gadget, &audio_dev->func, ep);
+	if (ret < 0) {
+		dev_err(dev, "config_ep_by_speed for out_ep failed (%d)\n", ret);
+		return ret;
+	}
+
 	req_len = ep->maxpacket;
 
 	prm->ep_enabled = true;
-	usb_ep_enable(ep);
+	ret = usb_ep_enable(ep);
+	if (ret < 0) {
+		dev_err(dev, "usb_ep_enable failed for out_ep (%d)\n", ret);
+		return ret;
+	}
 
 	for (i = 0; i < params->req_number; i++) {
 		if (!prm->reqs[i]) {
@@ -508,9 +517,18 @@
 		return 0;
 
 	/* Setup feedback endpoint */
-	config_ep_by_speed(gadget, &audio_dev->func, ep_fback);
+	ret = config_ep_by_speed(gadget, &audio_dev->func, ep_fback);
+	if (ret < 0) {
+		dev_err(dev, "config_ep_by_speed in_ep_fback failed (%d)\n", ret);
+		return ret; // TODO: Clean up out_ep
+	}
+
 	prm->fb_ep_enabled = true;
-	usb_ep_enable(ep_fback);
+	ret = usb_ep_enable(ep_fback);
+	if (ret < 0) {
+		dev_err(dev, "usb_ep_enable failed for in_ep_fback (%d)\n", ret);
+		return ret; // TODO: Clean up out_ep
+	}
 	req_len = ep_fback->maxpacket;
 
 	req_fback = usb_ep_alloc_request(ep_fback, GFP_ATOMIC);
@@ -565,11 +583,15 @@
 	struct uac_params *params = &audio_dev->params;
 	unsigned int factor;
 	const struct usb_endpoint_descriptor *ep_desc;
-	int req_len, i;
+	int req_len, i, ret;
 
 	ep = audio_dev->in_ep;
 	prm = &uac->p_prm;
-	config_ep_by_speed(gadget, &audio_dev->func, ep);
+	ret = config_ep_by_speed(gadget, &audio_dev->func, ep);
+	if (ret < 0) {
+		dev_err(dev, "config_ep_by_speed for in_ep failed (%d)\n", ret);
+		return ret;
+	}
 
 	ep_desc = ep->desc;
 
@@ -598,7 +620,11 @@
 	uac->p_residue = 0;
 
 	prm->ep_enabled = true;
-	usb_ep_enable(ep);
+	ret = usb_ep_enable(ep);
+	if (ret < 0) {
+		dev_err(dev, "usb_ep_enable failed for in_ep (%d)\n", ret);
+		return ret;
+	}
 
 	for (i = 0; i < params->req_number; i++) {
 		if (!prm->reqs[i]) {
@@ -1097,7 +1123,7 @@
 			}
 
 			kctl->id.device = pcm->device;
-			kctl->id.subdevice = i;
+			kctl->id.subdevice = 0;
 
 			err = snd_ctl_add(card, kctl);
 			if (err < 0)
@@ -1120,7 +1146,7 @@
 			}
 
 			kctl->id.device = pcm->device;
-			kctl->id.subdevice = i;
+			kctl->id.subdevice = 0;
 
 
 			kctl->tlv.c = u_audio_volume_tlv;
@@ -1172,9 +1198,11 @@
 		return;
 
 	uac = g_audio->uac;
+	g_audio->uac = NULL;
+
 	card = uac->card;
 	if (card)
-		snd_card_free(card);
+		snd_card_free_when_closed(card);
 
 	kfree(uac->p_prm.reqs);
 	kfree(uac->c_prm.reqs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/u_ether.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/u_ether.c
@@ -17,6 +17,8 @@
 #include <linux/etherdevice.h>
 #include <linux/ethtool.h>
 #include <linux/if_vlan.h>
+#include <linux/etherdevice.h>
+#include <linux/string_helpers.h>
 
 #include "u_ether.h"
 
@@ -773,9 +775,13 @@
 	dev->qmult = qmult;
 	snprintf(net->name, sizeof(net->name), "%s%%d", netname);
 
-	if (get_ether_addr(dev_addr, net->dev_addr))
+	if (get_ether_addr(dev_addr, net->dev_addr)) {
+		net->addr_assign_type = NET_ADDR_RANDOM;
 		dev_warn(&g->dev,
 			"using random %s ethernet address\n", "self");
+	} else {
+		net->addr_assign_type = NET_ADDR_SET;
+	}
 	if (get_ether_addr(host_addr, dev->host_mac))
 		dev_warn(&g->dev,
 			"using random %s ethernet address\n", "host");
@@ -832,6 +838,9 @@
 	INIT_LIST_HEAD(&dev->tx_reqs);
 	INIT_LIST_HEAD(&dev->rx_reqs);
 
+	/* by default we always have a random MAC address */
+	net->addr_assign_type = NET_ADDR_RANDOM;
+
 	skb_queue_head_init(&dev->rx_frames);
 
 	/* network device setup */
@@ -861,19 +870,22 @@
 {
 	struct eth_dev *dev;
 	struct usb_gadget *g;
-	struct sockaddr sa;
 	int status;
 
 	if (!net->dev.parent)
 		return -EINVAL;
 	dev = netdev_priv(net);
 	g = dev->gadget;
+
+	eth_hw_addr_set(net, dev->dev_mac);
+
 	status = register_netdev(net);
 	if (status < 0) {
 		dev_dbg(&g->dev, "register_netdev failed, %d\n", status);
 		return status;
 	} else {
 		INFO(dev, "HOST MAC %pM\n", dev->host_mac);
+		INFO(dev, "MAC %pM\n", dev->dev_mac);
 
 		/* two kinds of host-initiated state changes:
 		 *  - iff DATA transfer is active, carrier is "on"
@@ -881,15 +893,6 @@
 		 */
 		netif_carrier_off(net);
 	}
-	sa.sa_family = net->type;
-	memcpy(sa.sa_data, dev->dev_mac, ETH_ALEN);
-	rtnl_lock();
-	status = dev_set_mac_address(net, &sa, NULL);
-	rtnl_unlock();
-	if (status)
-		pr_warn("cannot set self ethernet address: %d\n", status);
-	else
-		INFO(dev, "MAC %pM\n", dev->dev_mac);
 
 	return status;
 }
@@ -914,6 +917,7 @@
 	if (get_ether_addr(dev_addr, new_addr))
 		return -EINVAL;
 	memcpy(dev->dev_mac, new_addr, ETH_ALEN);
+	net->addr_assign_type = NET_ADDR_SET;
 	return 0;
 }
 EXPORT_SYMBOL_GPL(gether_set_dev_addr);
@@ -973,6 +977,8 @@
 	dev = netdev_priv(net);
 	snprintf(host_addr, len, "%pm", dev->host_mac);
 
+	string_upper(host_addr, host_addr);
+
 	return strlen(host_addr);
 }
 EXPORT_SYMBOL_GPL(gether_get_host_addr_cdc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/u_serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/u_serial.c
@@ -81,6 +81,9 @@
 #define WRITE_BUF_SIZE		8192		/* TX only */
 #define GS_CONSOLE_BUF_SIZE	8192
 
+/* Prevents race conditions while accessing gser->ioport */
+static DEFINE_SPINLOCK(serial_port_lock);
+
 /* console info */
 struct gs_console {
 	struct console		console;
@@ -567,9 +570,12 @@
 		 * we didn't in gs_start_tx() */
 		tty_wakeup(port->port.tty);
 	} else {
-		gs_free_requests(ep, head, &port->read_allocated);
-		gs_free_requests(port->port_usb->in, &port->write_pool,
-			&port->write_allocated);
+		/* Free reqs only if we are still connected */
+		if (port->port_usb) {
+			gs_free_requests(ep, head, &port->read_allocated);
+			gs_free_requests(port->port_usb->in, &port->write_pool,
+				&port->write_allocated);
+		}
 		status = -EIO;
 	}
 
@@ -912,8 +918,11 @@
 	}
 
 	req->length = size;
+
+	spin_unlock_irq(&cons->lock);
 	if (usb_ep_queue(ep, req, GFP_ATOMIC))
 		req->length = 0;
+	spin_lock_irq(&cons->lock);
 }
 
 static void gs_console_work(struct work_struct *work)
@@ -1374,8 +1383,10 @@
 	if (!port)
 		return;
 
+	spin_lock_irqsave(&serial_port_lock, flags);
+
 	/* tell the TTY glue not to do I/O here any more */
-	spin_lock_irqsave(&port->port_lock, flags);
+	spin_lock(&port->port_lock);
 
 	gs_console_disconnect(port);
 
@@ -1390,7 +1401,8 @@
 			tty_hangup(port->port.tty);
 	}
 	port->suspended = false;
-	spin_unlock_irqrestore(&port->port_lock, flags);
+	spin_unlock(&port->port_lock);
+	spin_unlock_irqrestore(&serial_port_lock, flags);
 
 	/* disable endpoints, aborting down any active I/O */
 	usb_ep_disable(gser->out);
@@ -1413,21 +1425,40 @@
 
 void gserial_suspend(struct gserial *gser)
 {
-	struct gs_port	*port = gser->ioport;
+	struct gs_port	*port;
 	unsigned long	flags;
 
-	spin_lock_irqsave(&port->port_lock, flags);
+	spin_lock_irqsave(&serial_port_lock, flags);
+	port = gser->ioport;
+
+	if (!port) {
+		spin_unlock_irqrestore(&serial_port_lock, flags);
+		return;
+	}
+
+	spin_lock(&port->port_lock);
+	spin_unlock(&serial_port_lock);
 	port->suspended = true;
+	port->start_delayed = true;
 	spin_unlock_irqrestore(&port->port_lock, flags);
 }
 EXPORT_SYMBOL_GPL(gserial_suspend);
 
 void gserial_resume(struct gserial *gser)
 {
-	struct gs_port *port = gser->ioport;
+	struct gs_port *port;
 	unsigned long	flags;
 
-	spin_lock_irqsave(&port->port_lock, flags);
+	spin_lock_irqsave(&serial_port_lock, flags);
+	port = gser->ioport;
+
+	if (!port) {
+		spin_unlock_irqrestore(&serial_port_lock, flags);
+		return;
+	}
+
+	spin_lock(&port->port_lock);
+	spin_unlock(&serial_port_lock);
 	port->suspended = false;
 	if (!port->start_delayed) {
 		spin_unlock_irqrestore(&port->port_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc.h
@@ -14,6 +14,7 @@
 #include <linux/spinlock.h>
 #include <linux/usb/composite.h>
 #include <linux/videodev2.h>
+#include <linux/wait.h>
 
 #include <media/v4l2-device.h>
 #include <media/v4l2-dev.h>
@@ -68,6 +69,8 @@
 #define UVC_MAX_REQUEST_SIZE			64
 #define UVC_MAX_EVENTS				4
 
+#define UVCG_REQUEST_HEADER_LEN			2
+
 /* ------------------------------------------------------------------------
  * Structures
  */
@@ -76,7 +79,8 @@
 	u8 *req_buffer;
 	struct uvc_video *video;
 	struct sg_table sgt;
-	u8 header[2];
+	u8 header[UVCG_REQUEST_HEADER_LEN];
+	struct uvc_buffer *last_buf;
 };
 
 struct uvc_video {
@@ -126,6 +130,8 @@
 	enum uvc_state state;
 	struct usb_function func;
 	struct uvc_video video;
+	bool func_connected;
+	wait_queue_head_t func_connected_queue;
 
 	/* Descriptors */
 	struct {
@@ -156,6 +162,7 @@
 struct uvc_file_handle {
 	struct v4l2_fh vfh;
 	struct uvc_video *device;
+	bool is_uvc_app_handle;
 };
 
 #define to_uvc_file_handle(handle) \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc_configfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc_configfs.c
@@ -505,11 +505,68 @@
 UVCG_DEFAULT_OUTPUT_ATTR(b_terminal_id, bTerminalID, 8);
 UVCG_DEFAULT_OUTPUT_ATTR(w_terminal_type, wTerminalType, 16);
 UVCG_DEFAULT_OUTPUT_ATTR(b_assoc_terminal, bAssocTerminal, 8);
-UVCG_DEFAULT_OUTPUT_ATTR(b_source_id, bSourceID, 8);
 UVCG_DEFAULT_OUTPUT_ATTR(i_terminal, iTerminal, 8);
 
 #undef UVCG_DEFAULT_OUTPUT_ATTR
 
+static ssize_t uvcg_default_output_b_source_id_show(struct config_item *item,
+						    char *page)
+{
+	struct config_group *group = to_config_group(item);
+	struct f_uvc_opts *opts;
+	struct config_item *opts_item;
+	struct mutex *su_mutex = &group->cg_subsys->su_mutex;
+	struct uvc_output_terminal_descriptor *cd;
+	int result;
+
+	mutex_lock(su_mutex); /* for navigating configfs hierarchy */
+
+	opts_item = group->cg_item.ci_parent->ci_parent->
+			ci_parent->ci_parent;
+	opts = to_f_uvc_opts(opts_item);
+	cd = &opts->uvc_output_terminal;
+
+	mutex_lock(&opts->lock);
+	result = sprintf(page, "%u\n", le8_to_cpu(cd->bSourceID));
+	mutex_unlock(&opts->lock);
+
+	mutex_unlock(su_mutex);
+
+	return result;
+}
+
+static ssize_t uvcg_default_output_b_source_id_store(struct config_item *item,
+						     const char *page, size_t len)
+{
+	struct config_group *group = to_config_group(item);
+	struct f_uvc_opts *opts;
+	struct config_item *opts_item;
+	struct mutex *su_mutex = &group->cg_subsys->su_mutex;
+	struct uvc_output_terminal_descriptor *cd;
+	int result;
+	u8 num;
+
+	result = kstrtou8(page, 0, &num);
+	if (result)
+		return result;
+
+	mutex_lock(su_mutex); /* for navigating configfs hierarchy */
+
+	opts_item = group->cg_item.ci_parent->ci_parent->
+			ci_parent->ci_parent;
+	opts = to_f_uvc_opts(opts_item);
+	cd = &opts->uvc_output_terminal;
+
+	mutex_lock(&opts->lock);
+	cd->bSourceID = num;
+	mutex_unlock(&opts->lock);
+
+	mutex_unlock(su_mutex);
+
+	return len;
+}
+UVC_ATTR(uvcg_default_output_, b_source_id, bSourceID);
+
 static struct configfs_attribute *uvcg_default_output_attrs[] = {
 	&uvcg_default_output_attr_b_terminal_id,
 	&uvcg_default_output_attr_w_terminal_type,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc_queue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc_queue.c
@@ -44,7 +44,8 @@
 {
 	struct uvc_video_queue *queue = vb2_get_drv_priv(vq);
 	struct uvc_video *video = container_of(queue, struct uvc_video, queue);
-	struct usb_composite_dev *cdev = video->uvc->func.config->cdev;
+	unsigned int req_size;
+	unsigned int nreq;
 
 	if (*nbuffers > UVC_MAX_VIDEO_BUFFERS)
 		*nbuffers = UVC_MAX_VIDEO_BUFFERS;
@@ -53,10 +54,16 @@
 
 	sizes[0] = video->imagesize;
 
-	if (cdev->gadget->speed < USB_SPEED_SUPER)
-		video->uvc_num_requests = 4;
-	else
-		video->uvc_num_requests = 64;
+	req_size = video->ep->maxpacket
+		 * max_t(unsigned int, video->ep->maxburst, 1)
+		 * (video->ep->mult);
+
+	/* We divide by two, to increase the chance to run
+	 * into fewer requests for smaller framesizes.
+	 */
+	nreq = DIV_ROUND_UP(DIV_ROUND_UP(sizes[0], 2), req_size);
+	nreq = clamp(nreq, 4U, 64U);
+	video->uvc_num_requests = nreq;
 
 	return 0;
 }
@@ -264,6 +271,8 @@
 		buf->state = UVC_BUF_STATE_ERROR;
 		vb2_buffer_done(&buf->buf.vb2_buf, VB2_BUF_STATE_ERROR);
 	}
+	queue->buf_used = 0;
+
 	/* This must be protected by the irqlock spinlock to avoid race
 	 * conditions between uvc_queue_buffer and the disconnection event that
 	 * could result in an interruptible wait in uvc_dequeue_buffer. Do not
@@ -304,6 +313,7 @@
 
 		queue->sequence = 0;
 		queue->buf_used = 0;
+		queue->flags &= ~UVC_QUEUE_DROP_INCOMPLETE;
 	} else {
 		ret = vb2_streamoff(&queue->queue, queue->queue.type);
 		if (ret < 0)
@@ -326,33 +336,23 @@
 }
 
 /* called with &queue_irqlock held.. */
-struct uvc_buffer *uvcg_queue_next_buffer(struct uvc_video_queue *queue,
+void uvcg_complete_buffer(struct uvc_video_queue *queue,
 					  struct uvc_buffer *buf)
 {
-	struct uvc_buffer *nextbuf;
-
-	if ((queue->flags & UVC_QUEUE_DROP_INCOMPLETE) &&
-	     buf->length != buf->bytesused) {
-		buf->state = UVC_BUF_STATE_QUEUED;
+	if (queue->flags & UVC_QUEUE_DROP_INCOMPLETE) {
+		queue->flags &= ~UVC_QUEUE_DROP_INCOMPLETE;
+		buf->state = UVC_BUF_STATE_ERROR;
 		vb2_set_plane_payload(&buf->buf.vb2_buf, 0, 0);
-		return buf;
+		vb2_buffer_done(&buf->buf.vb2_buf, VB2_BUF_STATE_ERROR);
+		return;
 	}
 
-	list_del(&buf->queue);
-	if (!list_empty(&queue->irqqueue))
-		nextbuf = list_first_entry(&queue->irqqueue, struct uvc_buffer,
-					   queue);
-	else
-		nextbuf = NULL;
-
 	buf->buf.field = V4L2_FIELD_NONE;
 	buf->buf.sequence = queue->sequence++;
 	buf->buf.vb2_buf.timestamp = ktime_get_ns();
 
 	vb2_set_plane_payload(&buf->buf.vb2_buf, 0, buf->bytesused);
 	vb2_buffer_done(&buf->buf.vb2_buf, VB2_BUF_STATE_DONE);
-
-	return nextbuf;
 }
 
 struct uvc_buffer *uvcg_queue_head(struct uvc_video_queue *queue)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc_queue.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc_queue.h
@@ -93,7 +93,7 @@
 
 int uvcg_queue_enable(struct uvc_video_queue *queue, int enable);
 
-struct uvc_buffer *uvcg_queue_next_buffer(struct uvc_video_queue *queue,
+void uvcg_complete_buffer(struct uvc_video_queue *queue,
 					  struct uvc_buffer *buf);
 
 struct uvc_buffer *uvcg_queue_head(struct uvc_video_queue *queue);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc_v4l2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc_v4l2.c
@@ -227,17 +227,56 @@
 uvc_v4l2_subscribe_event(struct v4l2_fh *fh,
 			 const struct v4l2_event_subscription *sub)
 {
+	struct uvc_device *uvc = video_get_drvdata(fh->vdev);
+	struct uvc_file_handle *handle = to_uvc_file_handle(fh);
+	int ret;
+
 	if (sub->type < UVC_EVENT_FIRST || sub->type > UVC_EVENT_LAST)
 		return -EINVAL;
 
-	return v4l2_event_subscribe(fh, sub, 2, NULL);
+	if (sub->type == UVC_EVENT_SETUP && uvc->func_connected)
+		return -EBUSY;
+
+	ret = v4l2_event_subscribe(fh, sub, 2, NULL);
+	if (ret < 0)
+		return ret;
+
+	if (sub->type == UVC_EVENT_SETUP) {
+		uvc->func_connected = true;
+		handle->is_uvc_app_handle = true;
+		uvc_function_connect(uvc);
+	}
+
+	return 0;
+}
+
+static void uvc_v4l2_disable(struct uvc_device *uvc)
+{
+	uvc_function_disconnect(uvc);
+	uvcg_video_enable(&uvc->video, 0);
+	uvcg_free_buffers(&uvc->video.queue);
+	uvc->func_connected = false;
+	wake_up_interruptible(&uvc->func_connected_queue);
 }
 
 static int
 uvc_v4l2_unsubscribe_event(struct v4l2_fh *fh,
 			   const struct v4l2_event_subscription *sub)
 {
-	return v4l2_event_unsubscribe(fh, sub);
+	struct uvc_device *uvc = video_get_drvdata(fh->vdev);
+	struct uvc_file_handle *handle = to_uvc_file_handle(fh);
+	int ret;
+
+	ret = v4l2_event_unsubscribe(fh, sub);
+	if (ret < 0)
+		return ret;
+
+	if (sub->type == UVC_EVENT_SETUP && handle->is_uvc_app_handle) {
+		uvc_v4l2_disable(uvc);
+		handle->is_uvc_app_handle = false;
+	}
+
+	return 0;
 }
 
 static long
@@ -292,7 +331,6 @@
 	handle->device = &uvc->video;
 	file->private_data = &handle->vfh;
 
-	uvc_function_connect(uvc);
 	return 0;
 }
 
@@ -304,11 +342,9 @@
 	struct uvc_file_handle *handle = to_uvc_file_handle(file->private_data);
 	struct uvc_video *video = handle->device;
 
-	uvc_function_disconnect(uvc);
-
 	mutex_lock(&video->mutex);
-	uvcg_video_enable(video, 0);
-	uvcg_free_buffers(&video->queue);
+	if (handle->is_uvc_app_handle)
+		uvc_v4l2_disable(uvc);
 	mutex_unlock(&video->mutex);
 
 	file->private_data = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc_video.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc_video.c
@@ -33,7 +33,7 @@
 	if (buf->bytesused - video->queue.buf_used <= len - UVCG_REQUEST_HEADER_LEN)
 		data[1] |= UVC_STREAM_EOF;
 
-	return 2;
+	return UVCG_REQUEST_HEADER_LEN;
 }
 
 static int
@@ -59,6 +59,7 @@
 		struct uvc_buffer *buf)
 {
 	void *mem = req->buf;
+	struct uvc_request *ureq = req->context;
 	int len = video->req_size;
 	int ret;
 
@@ -83,13 +84,15 @@
 	if (buf->bytesused == video->queue.buf_used) {
 		video->queue.buf_used = 0;
 		buf->state = UVC_BUF_STATE_DONE;
-		uvcg_queue_next_buffer(&video->queue, buf);
+		list_del(&buf->queue);
 		video->fid ^= UVC_STREAM_FID;
+		ureq->last_buf = buf;
 
 		video->payload_size = 0;
 	}
 
 	if (video->payload_size == video->max_payload_size ||
+	    video->queue.flags & UVC_QUEUE_DROP_INCOMPLETE ||
 	    buf->bytesused == video->queue.buf_used)
 		video->payload_size = 0;
 }
@@ -104,31 +107,31 @@
 	unsigned int len = video->req_size;
 	unsigned int sg_left, part = 0;
 	unsigned int i;
-	int ret;
+	int header_len;
 
 	sg = ureq->sgt.sgl;
 	sg_init_table(sg, ureq->sgt.nents);
 
 	/* Init the header. */
-	ret = uvc_video_encode_header(video, buf, ureq->header,
+	header_len = uvc_video_encode_header(video, buf, ureq->header,
 				      video->req_size);
-	sg_set_buf(sg, ureq->header, UVCG_REQUEST_HEADER_LEN);
-	len -= ret;
+	sg_set_buf(sg, ureq->header, header_len);
+	len -= header_len;
 
 	if (pending <= len)
 		len = pending;
 
 	req->length = (len == pending) ?
-		len + UVCG_REQUEST_HEADER_LEN : video->req_size;
+		len + header_len : video->req_size;
 
 	/* Init the pending sgs with payload */
 	sg = sg_next(sg);
 
 	for_each_sg(sg, iter, ureq->sgt.nents - 1, i) {
-		if (!len || !buf->sg)
+		if (!len || !buf->sg || !buf->sg->length)
 			break;
 
-		sg_left = sg_dma_len(buf->sg) - buf->offset;
+		sg_left = buf->sg->length - buf->offset;
 		part = min_t(unsigned int, len, sg_left);
 
 		sg_set_page(iter, sg_page(buf->sg), part, buf->offset);
@@ -148,14 +151,16 @@
 	req->num_sgs = i + 1;
 
 	req->length -= len;
-	video->queue.buf_used += req->length - UVCG_REQUEST_HEADER_LEN;
+	video->queue.buf_used += req->length - header_len;
 
-	if (buf->bytesused == video->queue.buf_used || !buf->sg) {
+	if (buf->bytesused == video->queue.buf_used || !buf->sg ||
+			video->queue.flags & UVC_QUEUE_DROP_INCOMPLETE) {
 		video->queue.buf_used = 0;
 		buf->state = UVC_BUF_STATE_DONE;
 		buf->offset = 0;
-		uvcg_queue_next_buffer(&video->queue, buf);
+		list_del(&buf->queue);
 		video->fid ^= UVC_STREAM_FID;
+		ureq->last_buf = buf;
 	}
 }
 
@@ -164,6 +169,7 @@
 		struct uvc_buffer *buf)
 {
 	void *mem = req->buf;
+	struct uvc_request *ureq = req->context;
 	int len = video->req_size;
 	int ret;
 
@@ -178,11 +184,13 @@
 
 	req->length = video->req_size - len;
 
-	if (buf->bytesused == video->queue.buf_used) {
+	if (buf->bytesused == video->queue.buf_used ||
+			video->queue.flags & UVC_QUEUE_DROP_INCOMPLETE) {
 		video->queue.buf_used = 0;
 		buf->state = UVC_BUF_STATE_DONE;
-		uvcg_queue_next_buffer(&video->queue, buf);
+		list_del(&buf->queue);
 		video->fid ^= UVC_STREAM_FID;
+		ureq->last_buf = buf;
 	}
 }
 
@@ -219,18 +227,28 @@
 	case 0:
 		break;
 
+	case -EXDEV:
+		uvcg_dbg(&video->uvc->func, "VS request missed xfer.\n");
+		queue->flags |= UVC_QUEUE_DROP_INCOMPLETE;
+		break;
+
 	case -ESHUTDOWN:	/* disconnect from host. */
 		uvcg_dbg(&video->uvc->func, "VS request cancelled.\n");
 		uvcg_queue_cancel(queue, 1);
 		break;
 
 	default:
-		uvcg_info(&video->uvc->func,
+		uvcg_warn(&video->uvc->func,
 			  "VS request completed with status %d.\n",
 			  req->status);
 		uvcg_queue_cancel(queue, 0);
 	}
 
+	if (ureq->last_buf) {
+		uvcg_complete_buffer(&video->queue, ureq->last_buf);
+		ureq->last_buf = NULL;
+	}
+
 	spin_lock_irqsave(&video->req_lock, flags);
 	list_add_tail(&req->list, &video->req_free);
 	spin_unlock_irqrestore(&video->req_lock, flags);
@@ -298,12 +316,13 @@
 		video->ureq[i].req->complete = uvc_video_complete;
 		video->ureq[i].req->context = &video->ureq[i];
 		video->ureq[i].video = video;
+		video->ureq[i].last_buf = NULL;
 
 		list_add_tail(&video->ureq[i].req->list, &video->req_free);
 		/* req_size/PAGE_SIZE + 1 for overruns and + 1 for header */
 		sg_alloc_table(&video->ureq[i].sgt,
-			       DIV_ROUND_UP(req_size - 2, PAGE_SIZE) + 2,
-			       GFP_KERNEL);
+			       DIV_ROUND_UP(req_size - UVCG_REQUEST_HEADER_LEN,
+					    PAGE_SIZE) + 2, GFP_KERNEL);
 	}
 
 	video->req_size = req_size;
@@ -373,11 +392,13 @@
 			req->no_interrupt = 1;
 		}
 
-		/* Queue the USB request */
-		ret = uvcg_video_ep_queue(video, req);
 		spin_unlock_irqrestore(&queue->irqlock, flags);
 
+		/* Queue the USB request */
+		ret = uvcg_video_ep_queue(video, req);
 		if (ret < 0) {
+			printk(KERN_INFO "Failed to queue request (%d)\n", ret);
+			usb_ep_set_halt(video->ep);
 			uvcg_queue_cancel(queue, 0);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/function/uvc_video.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/function/uvc_video.h
@@ -12,8 +12,6 @@
 #ifndef __UVC_VIDEO_H__
 #define __UVC_VIDEO_H__
 
-#define UVCG_REQUEST_HEADER_LEN			2
-
 struct uvc_video;
 
 int uvcg_video_enable(struct uvc_video *video, int enable);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/legacy/dbgp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/legacy/dbgp.c
@@ -137,7 +137,7 @@
 		goto fail_1;
 	}
 
-	req->buf = kmalloc(DBGP_REQ_LEN, GFP_KERNEL);
+	req->buf = kzalloc(DBGP_REQ_LEN, GFP_KERNEL);
 	if (!req->buf) {
 		err = -ENOMEM;
 		stp = 2;
@@ -345,6 +345,19 @@
 	void *data = NULL;
 	u16 len = 0;
 
+	if (length > DBGP_REQ_LEN) {
+		if (ctrl->bRequestType & USB_DIR_IN) {
+			/* Cast away the const, we are going to overwrite on purpose. */
+			__le16 *temp = (__le16 *)&ctrl->wLength;
+
+			*temp = cpu_to_le16(DBGP_REQ_LEN);
+			length = DBGP_REQ_LEN;
+		} else {
+			return err;
+		}
+	}
+
+
 	if (request == USB_REQ_GET_DESCRIPTOR) {
 		switch (value>>8) {
 		case USB_DT_DEVICE:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/legacy/hid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/legacy/hid.c
@@ -99,8 +99,10 @@
 
 	list_for_each_entry(e, &hidg_func_list, node) {
 		e->f = usb_get_function(e->fi);
-		if (IS_ERR(e->f))
+		if (IS_ERR(e->f)) {
+			status = PTR_ERR(e->f);
 			goto put;
+		}
 		status = usb_add_function(c, e->f);
 		if (status < 0) {
 			usb_put_function(e->f);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/legacy/inode.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/legacy/inode.c
@@ -110,6 +110,8 @@
 /* enough for the whole queue: most events invalidate others */
 #define	N_EVENT			5
 
+#define RBUF_SIZE		256
+
 struct dev_data {
 	spinlock_t			lock;
 	refcount_t			count;
@@ -144,7 +146,7 @@
 	struct dentry			*dentry;
 
 	/* except this scratch i/o buffer for ep0 */
-	u8				rbuf [256];
+	u8				rbuf[RBUF_SIZE];
 };
 
 static inline void get_dev (struct dev_data *data)
@@ -227,6 +229,7 @@
  */
 
 static const char *CHIP;
+static DEFINE_MUTEX(sb_mutex);		/* Serialize superblock operations */
 
 /*----------------------------------------------------------------------*/
 
@@ -360,6 +363,7 @@
 				spin_unlock_irq (&epdata->dev->lock);
 
 				DBG (epdata->dev, "endpoint gone\n");
+				wait_for_completion(&done);
 				epdata->status = -ENODEV;
 			}
 		}
@@ -1334,6 +1338,18 @@
 	u16				w_value = le16_to_cpu(ctrl->wValue);
 	u16				w_length = le16_to_cpu(ctrl->wLength);
 
+	if (w_length > RBUF_SIZE) {
+		if (ctrl->bRequestType & USB_DIR_IN) {
+			/* Cast away the const, we are going to overwrite on purpose. */
+			__le16 *temp = (__le16 *)&ctrl->wLength;
+
+			*temp = cpu_to_le16(RBUF_SIZE);
+			w_length = RBUF_SIZE;
+		} else {
+			return value;
+		}
+	}
+
 	spin_lock (&dev->lock);
 	dev->setup_abort = 0;
 	if (dev->state == STATE_DEV_UNCONNECTED) {
@@ -1815,8 +1831,9 @@
 	spin_lock_irq (&dev->lock);
 	value = -EINVAL;
 	if (dev->buf) {
+		spin_unlock_irq(&dev->lock);
 		kfree(kbuf);
-		goto fail;
+		return value;
 	}
 	dev->buf = kbuf;
 
@@ -1863,8 +1880,8 @@
 
 	value = usb_gadget_probe_driver(&gadgetfs_driver);
 	if (value != 0) {
-		kfree (dev->buf);
-		dev->buf = NULL;
+		spin_lock_irq(&dev->lock);
+		goto fail;
 	} else {
 		/* at this point "good" hardware has for the first time
 		 * let the USB the host see us.  alternatively, if users
@@ -1881,6 +1898,9 @@
 	return value;
 
 fail:
+	dev->config = NULL;
+	dev->hs_config = NULL;
+	dev->dev = NULL;
 	spin_unlock_irq (&dev->lock);
 	pr_debug ("%s: %s fail %zd, %p\n", shortname, __func__, value, dev);
 	kfree (dev->buf);
@@ -1994,13 +2014,20 @@
 {
 	struct inode	*inode;
 	struct dev_data	*dev;
+	int		rc;
 
-	if (the_device)
-		return -ESRCH;
+	mutex_lock(&sb_mutex);
+
+	if (the_device) {
+		rc = -ESRCH;
+		goto Done;
+	}
 
 	CHIP = usb_get_gadget_udc_name();
-	if (!CHIP)
-		return -ENODEV;
+	if (!CHIP) {
+		rc = -ENODEV;
+		goto Done;
+	}
 
 	/* superblock */
 	sb->s_blocksize = PAGE_SIZE;
@@ -2037,13 +2064,17 @@
 	 * from binding to a controller.
 	 */
 	the_device = dev;
-	return 0;
+	rc = 0;
+	goto Done;
 
-Enomem:
+ Enomem:
 	kfree(CHIP);
 	CHIP = NULL;
+	rc = -ENOMEM;
 
-	return -ENOMEM;
+ Done:
+	mutex_unlock(&sb_mutex);
+	return rc;
 }
 
 /* "mount -t gadgetfs path /dev/gadget" ends up here */
@@ -2065,6 +2096,7 @@
 static void
 gadgetfs_kill_sb (struct super_block *sb)
 {
+	mutex_lock(&sb_mutex);
 	kill_litter_super (sb);
 	if (the_device) {
 		put_dev (the_device);
@@ -2072,6 +2104,7 @@
 	}
 	kfree(CHIP);
 	CHIP = NULL;
+	mutex_unlock(&sb_mutex);
 }
 
 /*----------------------------------------------------------------------*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/legacy/raw_gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/legacy/raw_gadget.c
@@ -11,6 +11,7 @@
 #include <linux/ctype.h>
 #include <linux/debugfs.h>
 #include <linux/delay.h>
+#include <linux/idr.h>
 #include <linux/kref.h>
 #include <linux/miscdevice.h>
 #include <linux/module.h>
@@ -36,6 +37,9 @@
 
 /*----------------------------------------------------------------------*/
 
+static DEFINE_IDA(driver_id_numbers);
+#define DRIVER_DRIVER_NAME_LENGTH_MAX	32
+
 #define RAW_EVENT_QUEUE_SIZE	16
 
 struct raw_event_queue {
@@ -145,6 +149,7 @@
 	STATE_DEV_INVALID = 0,
 	STATE_DEV_OPENED,
 	STATE_DEV_INITIALIZED,
+	STATE_DEV_REGISTERING,
 	STATE_DEV_RUNNING,
 	STATE_DEV_CLOSED,
 	STATE_DEV_FAILED
@@ -160,6 +165,9 @@
 	/* Reference to misc device: */
 	struct device			*dev;
 
+	/* Make driver names unique */
+	int				driver_id_number;
+
 	/* Protected by lock: */
 	enum dev_state			state;
 	bool				gadget_registered;
@@ -188,6 +196,7 @@
 	spin_lock_init(&dev->lock);
 	init_completion(&dev->ep0_done);
 	raw_event_queue_init(&dev->queue);
+	dev->driver_id_number = -1;
 	return dev;
 }
 
@@ -198,6 +207,9 @@
 
 	kfree(dev->udc_name);
 	kfree(dev->driver.udc_name);
+	kfree(dev->driver.driver.name);
+	if (dev->driver_id_number >= 0)
+		ida_free(&driver_id_numbers, dev->driver_id_number);
 	if (dev->req) {
 		if (dev->ep0_urb_queued)
 			usb_ep_dequeue(dev->gadget->ep0, dev->req);
@@ -298,13 +310,15 @@
 	dev->eps_num = i;
 	spin_unlock_irqrestore(&dev->lock, flags);
 
-	/* Matches kref_put() in gadget_unbind(). */
-	kref_get(&dev->count);
-
 	ret = raw_queue_event(dev, USB_RAW_EVENT_CONNECT, 0, NULL);
-	if (ret < 0)
+	if (ret < 0) {
 		dev_err(&gadget->dev, "failed to queue event\n");
+		set_gadget_data(gadget, NULL);
+		return ret;
+	}
 
+	/* Matches kref_put() in gadget_unbind(). */
+	kref_get(&dev->count);
 	return ret;
 }
 
@@ -418,9 +432,11 @@
 static int raw_ioctl_init(struct raw_dev *dev, unsigned long value)
 {
 	int ret = 0;
+	int driver_id_number;
 	struct usb_raw_init arg;
 	char *udc_driver_name;
 	char *udc_device_name;
+	char *driver_driver_name;
 	unsigned long flags;
 
 	if (copy_from_user(&arg, (void __user *)value, sizeof(arg)))
@@ -439,36 +455,43 @@
 		return -EINVAL;
 	}
 
+	driver_id_number = ida_alloc(&driver_id_numbers, GFP_KERNEL);
+	if (driver_id_number < 0)
+		return driver_id_number;
+
+	driver_driver_name = kmalloc(DRIVER_DRIVER_NAME_LENGTH_MAX, GFP_KERNEL);
+	if (!driver_driver_name) {
+		ret = -ENOMEM;
+		goto out_free_driver_id_number;
+	}
+	snprintf(driver_driver_name, DRIVER_DRIVER_NAME_LENGTH_MAX,
+				DRIVER_NAME ".%d", driver_id_number);
+
 	udc_driver_name = kmalloc(UDC_NAME_LENGTH_MAX, GFP_KERNEL);
-	if (!udc_driver_name)
-		return -ENOMEM;
+	if (!udc_driver_name) {
+		ret = -ENOMEM;
+		goto out_free_driver_driver_name;
+	}
 	ret = strscpy(udc_driver_name, &arg.driver_name[0],
 				UDC_NAME_LENGTH_MAX);
-	if (ret < 0) {
-		kfree(udc_driver_name);
-		return ret;
-	}
+	if (ret < 0)
+		goto out_free_udc_driver_name;
 	ret = 0;
 
 	udc_device_name = kmalloc(UDC_NAME_LENGTH_MAX, GFP_KERNEL);
 	if (!udc_device_name) {
-		kfree(udc_driver_name);
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto out_free_udc_driver_name;
 	}
 	ret = strscpy(udc_device_name, &arg.device_name[0],
 				UDC_NAME_LENGTH_MAX);
-	if (ret < 0) {
-		kfree(udc_driver_name);
-		kfree(udc_device_name);
-		return ret;
-	}
+	if (ret < 0)
+		goto out_free_udc_device_name;
 	ret = 0;
 
 	spin_lock_irqsave(&dev->lock, flags);
 	if (dev->state != STATE_DEV_OPENED) {
 		dev_dbg(dev->dev, "fail, device is not opened\n");
-		kfree(udc_driver_name);
-		kfree(udc_device_name);
 		ret = -EINVAL;
 		goto out_unlock;
 	}
@@ -483,14 +506,25 @@
 	dev->driver.suspend = gadget_suspend;
 	dev->driver.resume = gadget_resume;
 	dev->driver.reset = gadget_reset;
-	dev->driver.driver.name = DRIVER_NAME;
+	dev->driver.driver.name = driver_driver_name;
 	dev->driver.udc_name = udc_device_name;
 	dev->driver.match_existing_only = 1;
+	dev->driver_id_number = driver_id_number;
 
 	dev->state = STATE_DEV_INITIALIZED;
+	spin_unlock_irqrestore(&dev->lock, flags);
+	return ret;
 
 out_unlock:
 	spin_unlock_irqrestore(&dev->lock, flags);
+out_free_udc_device_name:
+	kfree(udc_device_name);
+out_free_udc_driver_name:
+	kfree(udc_driver_name);
+out_free_driver_driver_name:
+	kfree(driver_driver_name);
+out_free_driver_id_number:
+	ida_free(&driver_id_numbers, driver_id_number);
 	return ret;
 }
 
@@ -508,6 +542,7 @@
 		ret = -EINVAL;
 		goto out_unlock;
 	}
+	dev->state = STATE_DEV_REGISTERING;
 	spin_unlock_irqrestore(&dev->lock, flags);
 
 	ret = usb_gadget_probe_driver(&dev->driver);
@@ -628,12 +663,12 @@
 	if (WARN_ON(in && dev->ep0_out_pending)) {
 		ret = -ENODEV;
 		dev->state = STATE_DEV_FAILED;
-		goto out_done;
+		goto out_unlock;
 	}
 	if (WARN_ON(!in && dev->ep0_in_pending)) {
 		ret = -ENODEV;
 		dev->state = STATE_DEV_FAILED;
-		goto out_done;
+		goto out_unlock;
 	}
 
 	dev->req->buf = data;
@@ -648,7 +683,7 @@
 				"fail, usb_ep_queue returned %d\n", ret);
 		spin_lock_irqsave(&dev->lock, flags);
 		dev->state = STATE_DEV_FAILED;
-		goto out_done;
+		goto out_queue_failed;
 	}
 
 	ret = wait_for_completion_interruptible(&dev->ep0_done);
@@ -657,13 +692,16 @@
 		usb_ep_dequeue(dev->gadget->ep0, dev->req);
 		wait_for_completion(&dev->ep0_done);
 		spin_lock_irqsave(&dev->lock, flags);
-		goto out_done;
+		if (dev->ep0_status == -ECONNRESET)
+			dev->ep0_status = -EINTR;
+		goto out_interrupted;
 	}
 
 	spin_lock_irqsave(&dev->lock, flags);
-	ret = dev->ep0_status;
 
-out_done:
+out_interrupted:
+	ret = dev->ep0_status;
+out_queue_failed:
 	dev->ep0_urb_queued = false;
 out_unlock:
 	spin_unlock_irqrestore(&dev->lock, flags);
@@ -1004,7 +1042,7 @@
 		ret = -EBUSY;
 		goto out_unlock;
 	}
-	if ((in && !ep->ep->caps.dir_in) || (!in && ep->ep->caps.dir_in)) {
+	if (in != usb_endpoint_dir_in(ep->ep->desc)) {
 		dev_dbg(&dev->gadget->dev, "fail, wrong direction\n");
 		ret = -EINVAL;
 		goto out_unlock;
@@ -1025,7 +1063,7 @@
 				"fail, usb_ep_queue returned %d\n", ret);
 		spin_lock_irqsave(&dev->lock, flags);
 		dev->state = STATE_DEV_FAILED;
-		goto out_done;
+		goto out_queue_failed;
 	}
 
 	ret = wait_for_completion_interruptible(&done);
@@ -1034,13 +1072,16 @@
 		usb_ep_dequeue(ep->ep, ep->req);
 		wait_for_completion(&done);
 		spin_lock_irqsave(&dev->lock, flags);
-		goto out_done;
+		if (ep->status == -ECONNRESET)
+			ep->status = -EINTR;
+		goto out_interrupted;
 	}
 
 	spin_lock_irqsave(&dev->lock, flags);
-	ret = ep->status;
 
-out_done:
+out_interrupted:
+	ret = ep->status;
+out_queue_failed:
 	ep->urb_queued = false;
 out_unlock:
 	spin_unlock_irqrestore(&dev->lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/legacy/webcam.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/legacy/webcam.c
@@ -163,7 +163,7 @@
 	.bDescriptorType	= USB_DT_CS_INTERFACE,
 	.bDescriptorSubType	= UVC_VS_FORMAT_UNCOMPRESSED,
 	.bFormatIndex		= 1,
-	.bNumFrameDescriptors	= 2,
+	.bNumFrameDescriptors	= 4,
 	.guidFormat		=
 		{ 'Y',  'U',  'Y',  '2', 0x00, 0x00, 0x10, 0x00,
 		 0x80, 0x00, 0x00, 0xaa, 0x00, 0x38, 0x9b, 0x71},
@@ -176,10 +176,10 @@
 };
 
 DECLARE_UVC_FRAME_UNCOMPRESSED(1);
-DECLARE_UVC_FRAME_UNCOMPRESSED(3);
+DECLARE_UVC_FRAME_UNCOMPRESSED(5);
 
-static const struct UVC_FRAME_UNCOMPRESSED(3) uvc_frame_yuv_360p = {
-	.bLength		= UVC_DT_FRAME_UNCOMPRESSED_SIZE(3),
+static const struct UVC_FRAME_UNCOMPRESSED(5) uvc_frame_yuv_360p = {
+	.bLength		= UVC_DT_FRAME_UNCOMPRESSED_SIZE(5),
 	.bDescriptorType	= USB_DT_CS_INTERFACE,
 	.bDescriptorSubType	= UVC_VS_FRAME_UNCOMPRESSED,
 	.bFrameIndex		= 1,
@@ -189,15 +189,17 @@
 	.dwMinBitRate		= cpu_to_le32(18432000),
 	.dwMaxBitRate		= cpu_to_le32(55296000),
 	.dwMaxVideoFrameBufferSize	= cpu_to_le32(460800),
-	.dwDefaultFrameInterval	= cpu_to_le32(666666),
-	.bFrameIntervalType	= 3,
-	.dwFrameInterval[0]	= cpu_to_le32(666666),
-	.dwFrameInterval[1]	= cpu_to_le32(1000000),
-	.dwFrameInterval[2]	= cpu_to_le32(5000000),
+	.dwDefaultFrameInterval	= cpu_to_le32(166666),
+	.bFrameIntervalType	= 5,
+	.dwFrameInterval[0]	= cpu_to_le32(166666),
+	.dwFrameInterval[1]	= cpu_to_le32(333333),
+	.dwFrameInterval[2]	= cpu_to_le32(666666),
+	.dwFrameInterval[3]	= cpu_to_le32(1000000),
+	.dwFrameInterval[4]	= cpu_to_le32(5000000),
 };
 
-static const struct UVC_FRAME_UNCOMPRESSED(1) uvc_frame_yuv_720p = {
-	.bLength		= UVC_DT_FRAME_UNCOMPRESSED_SIZE(1),
+static const struct UVC_FRAME_UNCOMPRESSED(5) uvc_frame_yuv_720p = {
+	.bLength		= UVC_DT_FRAME_UNCOMPRESSED_SIZE(5),
 	.bDescriptorType	= USB_DT_CS_INTERFACE,
 	.bDescriptorSubType	= UVC_VS_FRAME_UNCOMPRESSED,
 	.bFrameIndex		= 2,
@@ -207,11 +209,54 @@
 	.dwMinBitRate		= cpu_to_le32(29491200),
 	.dwMaxBitRate		= cpu_to_le32(29491200),
 	.dwMaxVideoFrameBufferSize	= cpu_to_le32(1843200),
-	.dwDefaultFrameInterval	= cpu_to_le32(5000000),
-	.bFrameIntervalType	= 1,
-	.dwFrameInterval[0]	= cpu_to_le32(5000000),
+	.dwDefaultFrameInterval	= cpu_to_le32(166666),
+	.bFrameIntervalType	= 5,
+	.dwFrameInterval[0]	= cpu_to_le32(166666),
+	.dwFrameInterval[1]	= cpu_to_le32(333333),
+	.dwFrameInterval[2]	= cpu_to_le32(666666),
+	.dwFrameInterval[3]	= cpu_to_le32(1000000),
+	.dwFrameInterval[4]	= cpu_to_le32(5000000),
 };
 
+static const struct UVC_FRAME_UNCOMPRESSED(5) uvc_frame_yuv_1080p = {
+	.bLength		= UVC_DT_FRAME_UNCOMPRESSED_SIZE(5),
+	.bDescriptorType	= USB_DT_CS_INTERFACE,
+	.bDescriptorSubType	= UVC_VS_FRAME_UNCOMPRESSED,
+	.bFrameIndex		= 3,
+	.bmCapabilities		= 0,
+	.wWidth			= cpu_to_le16(1920),
+	.wHeight		= cpu_to_le16(1080),
+	.dwMinBitRate		= cpu_to_le32(66355200),
+	.dwMaxBitRate		= cpu_to_le32(66355200),
+	.dwMaxVideoFrameBufferSize	= cpu_to_le32(4147200),
+	.dwDefaultFrameInterval	= cpu_to_le32(166666),
+	.bFrameIntervalType	= 5,
+	.dwFrameInterval[0]	= cpu_to_le32(166666),
+	.dwFrameInterval[1]	= cpu_to_le32(333333),
+	.dwFrameInterval[2]	= cpu_to_le32(666666),
+	.dwFrameInterval[3]	= cpu_to_le32(1000000),
+	.dwFrameInterval[4]	= cpu_to_le32(5000000),
+};
+
+static const struct UVC_FRAME_UNCOMPRESSED(5) uvc_frame_yuv_2160p = {
+	.bLength		= UVC_DT_FRAME_UNCOMPRESSED_SIZE(5),
+	.bDescriptorType	= USB_DT_CS_INTERFACE,
+	.bDescriptorSubType	= UVC_VS_FRAME_UNCOMPRESSED,
+	.bFrameIndex		= 4,
+	.bmCapabilities		= 0,
+	.wWidth			= cpu_to_le16(3840),
+	.wHeight		= cpu_to_le16(2160),
+	.dwMinBitRate		= cpu_to_le32(265420800),
+	.dwMaxBitRate		= cpu_to_le32(265420800),
+	.dwMaxVideoFrameBufferSize	= cpu_to_le32(16588800),
+	.dwDefaultFrameInterval	= cpu_to_le32(166666),
+	.bFrameIntervalType	= 5,
+	.dwFrameInterval[0]	= cpu_to_le32(166666),
+	.dwFrameInterval[1]	= cpu_to_le32(333333),
+	.dwFrameInterval[2]	= cpu_to_le32(666666),
+	.dwFrameInterval[3]	= cpu_to_le32(1000000),
+	.dwFrameInterval[4]	= cpu_to_le32(5000000),
+};
 static const struct uvc_format_mjpeg uvc_format_mjpg = {
 	.bLength		= UVC_DT_FORMAT_MJPEG_SIZE,
 	.bDescriptorType	= USB_DT_CS_INTERFACE,
@@ -293,6 +338,9 @@
 	(const struct uvc_descriptor_header *) &uvc_format_yuv,
 	(const struct uvc_descriptor_header *) &uvc_frame_yuv_360p,
 	(const struct uvc_descriptor_header *) &uvc_frame_yuv_720p,
+	(const struct uvc_descriptor_header *) &uvc_frame_yuv_1080p,
+	(const struct uvc_descriptor_header *) &uvc_frame_yuv_2160p,
+	(const struct uvc_descriptor_header *) &uvc_color_matching,
 	(const struct uvc_descriptor_header *) &uvc_format_mjpg,
 	(const struct uvc_descriptor_header *) &uvc_frame_mjpg_360p,
 	(const struct uvc_descriptor_header *) &uvc_frame_mjpg_720p,
@@ -305,6 +353,9 @@
 	(const struct uvc_descriptor_header *) &uvc_format_yuv,
 	(const struct uvc_descriptor_header *) &uvc_frame_yuv_360p,
 	(const struct uvc_descriptor_header *) &uvc_frame_yuv_720p,
+	(const struct uvc_descriptor_header *) &uvc_frame_yuv_1080p,
+	(const struct uvc_descriptor_header *) &uvc_frame_yuv_2160p,
+	(const struct uvc_descriptor_header *) &uvc_color_matching,
 	(const struct uvc_descriptor_header *) &uvc_format_mjpg,
 	(const struct uvc_descriptor_header *) &uvc_frame_mjpg_360p,
 	(const struct uvc_descriptor_header *) &uvc_frame_mjpg_720p,
@@ -317,6 +368,9 @@
 	(const struct uvc_descriptor_header *) &uvc_format_yuv,
 	(const struct uvc_descriptor_header *) &uvc_frame_yuv_360p,
 	(const struct uvc_descriptor_header *) &uvc_frame_yuv_720p,
+	(const struct uvc_descriptor_header *) &uvc_frame_yuv_1080p,
+	(const struct uvc_descriptor_header *) &uvc_frame_yuv_2160p,
+	(const struct uvc_descriptor_header *) &uvc_color_matching,
 	(const struct uvc_descriptor_header *) &uvc_format_mjpg,
 	(const struct uvc_descriptor_header *) &uvc_frame_mjpg_360p,
 	(const struct uvc_descriptor_header *) &uvc_frame_mjpg_720p,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/Kconfig
@@ -311,7 +311,7 @@
 
 config USB_AMD5536UDC
 	tristate "AMD5536 UDC"
-	depends on USB_PCI
+	depends on USB_PCI && HAS_DMA
 	select USB_SNP_CORE
 	help
 	   The AMD5536 UDC is part of the AMD Geode CS5536, an x86 southbridge.
@@ -330,6 +330,7 @@
 config USB_FSL_QE
 	tristate "Freescale QE/CPM USB Device Controller"
 	depends on FSL_SOC && (QUICC_ENGINE || CPM)
+	depends on !64BIT || BROKEN
 	help
 	   Some of Freescale PowerPC processors have a Full Speed
 	   QE/CPM2 USB controller, which support device mode with 4
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/amd5536udc_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/amd5536udc_pci.c
@@ -170,6 +170,9 @@
 		retval = -ENODEV;
 		goto err_probe;
 	}
+
+	udc = dev;
+
 	return 0;
 
 err_probe:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/aspeed-vhub/hub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/aspeed-vhub/hub.c
@@ -1028,8 +1028,10 @@
 	/* Initialize vhub String Descriptors. */
 	INIT_LIST_HEAD(&vhub->vhub_str_desc);
 	desc_np = of_get_child_by_name(vhub_np, "vhub-strings");
-	if (desc_np)
+	if (desc_np) {
 		ret = ast_vhub_of_parse_str_desc(vhub, desc_np);
+		of_node_put(desc_np);
+	}
 	else
 		ret = ast_vhub_str_alloc_add(vhub, &ast_vhub_strings);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/bcm63xx_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/bcm63xx_udc.c
@@ -2259,7 +2259,7 @@
  */
 static void bcm63xx_udc_cleanup_debugfs(struct bcm63xx_udc *udc)
 {
-	debugfs_remove(debugfs_lookup(udc->gadget.name, usb_debug_root));
+	debugfs_lookup_and_remove(udc->gadget.name, usb_debug_root);
 }
 
 /***********************************************************************
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/bdc/bdc_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/bdc/bdc_udc.c
@@ -151,6 +151,7 @@
 	bdc->delayed_status = false;
 	bdc->reinit = reinit;
 	bdc->test_mode = false;
+	usb_gadget_set_state(&bdc->gadget, USB_STATE_NOTATTACHED);
 }
 
 /* TNotify wkaeup timer */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/core.c
@@ -101,12 +101,10 @@
 		goto out;
 
 	/* UDC drivers can't handle endpoints with maxpacket size 0 */
-	if (usb_endpoint_maxp(ep->desc) == 0) {
-		/*
-		 * We should log an error message here, but we can't call
-		 * dev_err() because there's no way to find the gadget
-		 * given only ep.
-		 */
+	if (!ep->desc || usb_endpoint_maxp(ep->desc) == 0) {
+		WARN_ONCE(1, "%s: ep%d (%s) has %s\n", __func__, ep->address, ep->name,
+			  (!ep->desc) ? "NULL descriptor" : "maxpacket 0");
+
 		ret = -EINVAL;
 		goto out;
 	}
@@ -275,7 +273,9 @@
 {
 	int ret = 0;
 
-	if (WARN_ON_ONCE(!ep->enabled && ep->address)) {
+	if (!ep->enabled && ep->address) {
+		pr_debug("USB gadget: queue request to disabled ep 0x%x (%s)\n",
+				 ep->address, ep->name);
 		ret = -ESHUTDOWN;
 		goto out;
 	}
@@ -509,6 +509,33 @@
 EXPORT_SYMBOL_GPL(usb_gadget_wakeup);
 
 /**
+ * usb_gadget_set_remote_wakeup - configures the device remote wakeup feature.
+ * @gadget:the device being configured for remote wakeup
+ * @set:value to be configured.
+ *
+ * set to one to enable remote wakeup feature and zero to disable it.
+ *
+ * returns zero on success, else negative errno.
+ */
+int usb_gadget_set_remote_wakeup(struct usb_gadget *gadget, int set)
+{
+	int ret = 0;
+
+	if (!gadget->ops->set_remote_wakeup) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	ret = gadget->ops->set_remote_wakeup(gadget, set);
+
+out:
+	trace_usb_gadget_set_remote_wakeup(gadget, ret);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(usb_gadget_set_remote_wakeup);
+
+/**
  * usb_gadget_set_selfpowered - sets the device selfpowered feature.
  * @gadget:the device being declared as self-powered
  *
@@ -1424,8 +1451,6 @@
 	dev_dbg(&udc->dev, "unregistering UDC driver [%s]\n",
 			udc->driver->function);
 
-	kobject_uevent(&udc->dev.kobj, KOBJ_CHANGE);
-
 	usb_gadget_disconnect(udc->gadget);
 	usb_gadget_disable_async_callbacks(udc);
 	if (udc->gadget->irq)
@@ -1434,8 +1459,9 @@
 	usb_gadget_udc_stop(udc);
 
 	udc->driver = NULL;
-	udc->dev.driver = NULL;
 	udc->gadget->dev.driver = NULL;
+
+	kobject_uevent(&udc->dev.kobj, KOBJ_CHANGE);
 }
 
 /**
@@ -1496,7 +1522,6 @@
 			driver->function);
 
 	udc->driver = driver;
-	udc->dev.driver = &driver->driver;
 	udc->gadget->dev.driver = &driver->driver;
 
 	usb_gadget_udc_set_speed(udc, driver->max_speed);
@@ -1519,7 +1544,6 @@
 		dev_err(&udc->dev, "failed to start %s: %d\n",
 			udc->driver->function, ret);
 	udc->driver = NULL;
-	udc->dev.driver = NULL;
 	udc->gadget->dev.driver = NULL;
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/fotg210-udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/fotg210-udc.c
@@ -629,10 +629,10 @@
 static void fotg210_set_address(struct fotg210_udc *fotg210,
 				struct usb_ctrlrequest *ctrl)
 {
-	if (ctrl->wValue >= 0x0100) {
+	if (le16_to_cpu(ctrl->wValue) >= 0x0100) {
 		fotg210_request_error(fotg210);
 	} else {
-		fotg210_set_dev_addr(fotg210, ctrl->wValue);
+		fotg210_set_dev_addr(fotg210, le16_to_cpu(ctrl->wValue));
 		fotg210_set_cxdone(fotg210);
 	}
 }
@@ -706,6 +706,20 @@
 	return value & INOUTEPMPSR_STL_EP ? 1 : 0;
 }
 
+/* For EP0 requests triggered by this driver (currently GET_STATUS response) */
+static void fotg210_ep0_complete(struct usb_ep *_ep, struct usb_request *req)
+{
+	struct fotg210_ep *ep;
+	struct fotg210_udc *fotg210;
+
+	ep = container_of(_ep, struct fotg210_ep, ep);
+	fotg210 = ep->fotg210;
+
+	if (req->status || req->actual != req->length) {
+		dev_warn(&fotg210->gadget.dev, "EP0 request failed: %d\n", req->status);
+	}
+}
+
 static void fotg210_get_status(struct fotg210_udc *fotg210,
 				struct usb_ctrlrequest *ctrl)
 {
@@ -713,17 +727,17 @@
 
 	switch (ctrl->bRequestType & USB_RECIP_MASK) {
 	case USB_RECIP_DEVICE:
-		fotg210->ep0_data = 1 << USB_DEVICE_SELF_POWERED;
+		fotg210->ep0_data = cpu_to_le16(1 << USB_DEVICE_SELF_POWERED);
 		break;
 	case USB_RECIP_INTERFACE:
-		fotg210->ep0_data = 0;
+		fotg210->ep0_data = cpu_to_le16(0);
 		break;
 	case USB_RECIP_ENDPOINT:
 		epnum = ctrl->wIndex & USB_ENDPOINT_NUMBER_MASK;
 		if (epnum)
 			fotg210->ep0_data =
-				fotg210_is_epnstall(fotg210->ep[epnum])
-				<< USB_ENDPOINT_HALT;
+				cpu_to_le16(fotg210_is_epnstall(fotg210->ep[epnum])
+					    << USB_ENDPOINT_HALT);
 		else
 			fotg210_request_error(fotg210);
 		break;
@@ -1172,6 +1186,8 @@
 	if (fotg210->ep0_req == NULL)
 		goto err_map;
 
+	fotg210->ep0_req->complete = fotg210_ep0_complete;
+
 	fotg210_init(fotg210);
 
 	fotg210_disable_unplug(fotg210);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/fsl_qe_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/fsl_qe_udc.c
@@ -1956,9 +1956,13 @@
 	} else if ((request_type & USB_RECIP_MASK) == USB_RECIP_ENDPOINT) {
 		/* Get endpoint status */
 		int pipe = index & USB_ENDPOINT_NUMBER_MASK;
-		struct qe_ep *target_ep = &udc->eps[pipe];
+		struct qe_ep *target_ep;
 		u16 usep;
 
+		if (pipe >= USB_MAX_ENDPOINTS)
+			goto stall;
+		target_ep = &udc->eps[pipe];
+
 		/* stall if endpoint doesn't exist */
 		if (!target_ep->ep.desc)
 			goto stall;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/fsl_udc_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/fsl_udc_core.c
@@ -2485,7 +2485,7 @@
 	/* setup the udc->eps[] for non-control endpoints and link
 	 * to gadget.ep_list */
 	for (i = 1; i < (int)(udc_controller->max_ep / 2); i++) {
-		char name[14];
+		char name[16];
 
 		sprintf(name, "ep%dout", i);
 		struct_ep_setup(udc_controller, i * 2, name, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/fusb300_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/fusb300_udc.c
@@ -1347,6 +1347,7 @@
 	usb_del_gadget_udc(&fusb300->gadget);
 	iounmap(fusb300->reg);
 	free_irq(platform_get_irq(pdev, 0), fusb300);
+	free_irq(platform_get_irq(pdev, 1), fusb300);
 
 	fusb300_free_request(&fusb300->ep[0]->ep, fusb300->ep0_req);
 	for (i = 0; i < FUSB300_MAX_NUM_EP; i++)
@@ -1432,7 +1433,7 @@
 			IRQF_SHARED, udc_name, fusb300);
 	if (ret < 0) {
 		pr_err("request_irq1 error (%d)\n", ret);
-		goto clean_up;
+		goto err_request_irq1;
 	}
 
 	INIT_LIST_HEAD(&fusb300->gadget.ep_list);
@@ -1471,7 +1472,7 @@
 				GFP_KERNEL);
 	if (fusb300->ep0_req == NULL) {
 		ret = -ENOMEM;
-		goto clean_up3;
+		goto err_alloc_request;
 	}
 
 	init_controller(fusb300);
@@ -1486,7 +1487,10 @@
 err_add_udc:
 	fusb300_free_request(&fusb300->ep[0]->ep, fusb300->ep0_req);
 
-clean_up3:
+err_alloc_request:
+	free_irq(ires1->start, fusb300);
+
+err_request_irq1:
 	free_irq(ires->start, fusb300);
 
 clean_up:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/gr_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/gr_udc.c
@@ -215,7 +215,7 @@
 
 static void gr_dfs_delete(struct gr_udc *dev)
 {
-	debugfs_remove(debugfs_lookup(dev_name(dev->dev), usb_debug_root));
+	debugfs_lookup_and_remove(dev_name(dev->dev), usb_debug_root);
 }
 
 #else /* !CONFIG_USB_GADGET_DEBUG_FS */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/lpc32xx_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/lpc32xx_udc.c
@@ -532,7 +532,7 @@
 
 static void remove_debug_file(struct lpc32xx_udc *udc)
 {
-	debugfs_remove(debugfs_lookup(debug_filename, NULL));
+	debugfs_lookup_and_remove(debug_filename, NULL);
 }
 
 #else
@@ -3014,6 +3014,7 @@
 	}
 
 	udc->isp1301_i2c_client = isp1301_get_client(isp1301_node);
+	of_node_put(isp1301_node);
 	if (!udc->isp1301_i2c_client) {
 		return -EPROBE_DEFER;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/net2272.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/net2272.c
@@ -2650,7 +2650,7 @@
 		goto err_req;
 	}
 
-	ret = net2272_probe_fin(dev, IRQF_TRIGGER_LOW);
+	ret = net2272_probe_fin(dev, irqflags);
 	if (ret)
 		goto err_io;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/pxa25x_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/pxa25x_udc.c
@@ -1341,7 +1341,7 @@
 		debugfs_create_file(dev->gadget.name, \
 			S_IRUGO, NULL, dev, &udc_debug_fops); \
 	} while (0)
-#define remove_debug_files(dev) debugfs_remove(debugfs_lookup(dev->gadget.name, NULL))
+#define remove_debug_files(dev) debugfs_lookup_and_remove(dev->gadget.name, NULL)
 
 #else	/* !CONFIG_USB_GADGET_DEBUG_FILES */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/pxa27x_udc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/pxa27x_udc.c
@@ -215,7 +215,7 @@
 
 static void pxa_cleanup_debugfs(struct pxa_udc *udc)
 {
-	debugfs_remove(debugfs_lookup(udc->gadget.name, usb_debug_root));
+	debugfs_lookup_and_remove(udc->gadget.name, usb_debug_root);
 }
 
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/renesas_usb3.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/renesas_usb3.c
@@ -306,7 +306,7 @@
 	struct list_head	queue;
 };
 
-#define USB3_EP_NAME_SIZE	8
+#define USB3_EP_NAME_SIZE	16
 struct renesas_usb3_ep {
 	struct usb_ep ep;
 	struct renesas_usb3 *usb3;
@@ -2378,6 +2378,8 @@
 	switch (role) {
 	case USB_ROLE_NONE:
 		usb3->connection_state = USB_ROLE_NONE;
+		if (cur_role == USB_ROLE_HOST)
+			device_release_driver(host);
 		if (usb3->driver)
 			usb3_disconnect(usb3);
 		usb3_vbus_out(usb3, false);
@@ -2566,6 +2568,7 @@
 	debugfs_remove_recursive(usb3->dentry);
 	device_remove_file(&pdev->dev, &dev_attr_role);
 
+	cancel_work_sync(&usb3->role_work);
 	usb_role_switch_unregister(usb3->role_sw);
 
 	usb_del_gadget_udc(&usb3->gadget);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/tegra-xudc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/tegra-xudc.c
@@ -32,9 +32,6 @@
 #include <linux/workqueue.h>
 
 /* XUSB_DEV registers */
-#define SPARAM 0x000
-#define  SPARAM_ERSTMAX_MASK GENMASK(20, 16)
-#define  SPARAM_ERSTMAX(x) (((x) << 16) & SPARAM_ERSTMAX_MASK)
 #define DB 0x004
 #define  DB_TARGET_MASK GENMASK(15, 8)
 #define  DB_TARGET(x) (((x) << 8) & DB_TARGET_MASK)
@@ -275,8 +272,10 @@
 BUILD_EP_CONTEXT_RW(avg_trb_len, tx_info, 0, 0xffff)
 BUILD_EP_CONTEXT_RW(max_esit_payload, tx_info, 16, 0xffff)
 BUILD_EP_CONTEXT_RW(edtla, rsvd[0], 0, 0xffffff)
-BUILD_EP_CONTEXT_RW(seq_num, rsvd[0], 24, 0xff)
+BUILD_EP_CONTEXT_RW(rsvd, rsvd[0], 24, 0x1)
 BUILD_EP_CONTEXT_RW(partial_td, rsvd[0], 25, 0x1)
+BUILD_EP_CONTEXT_RW(splitxstate, rsvd[0], 26, 0x1)
+BUILD_EP_CONTEXT_RW(seq_num, rsvd[0], 27, 0x1f)
 BUILD_EP_CONTEXT_RW(cerrcnt, rsvd[1], 18, 0x3)
 BUILD_EP_CONTEXT_RW(data_offset, rsvd[2], 0, 0x1ffff)
 BUILD_EP_CONTEXT_RW(numtrbs, rsvd[2], 22, 0x1f)
@@ -1557,6 +1556,9 @@
 		ep_reload(xudc, ep->index);
 
 		ep_ctx_write_state(ep->context, EP_STATE_RUNNING);
+		ep_ctx_write_rsvd(ep->context, 0);
+		ep_ctx_write_partial_td(ep->context, 0);
+		ep_ctx_write_splitxstate(ep->context, 0);
 		ep_ctx_write_seq_num(ep->context, 0);
 
 		ep_reload(xudc, ep->index);
@@ -2152,7 +2154,7 @@
 
 	dev_dbg(xudc->dev, "%s: %u mA\n", __func__, m_a);
 
-	if (xudc->curr_usbphy->chg_type == SDP_TYPE)
+	if (xudc->curr_usbphy && xudc->curr_usbphy->chg_type == SDP_TYPE)
 		ret = usb_phy_set_power(xudc->curr_usbphy, m_a);
 
 	return ret;
@@ -2812,7 +2814,10 @@
 	xudc->setup_seq_num = 0;
 	xudc->queued_setup_packet = false;
 
-	ep_ctx_write_seq_num(ep0->context, xudc->setup_seq_num);
+	ep_ctx_write_rsvd(ep0->context, 0);
+	ep_ctx_write_partial_td(ep0->context, 0);
+	ep_ctx_write_splitxstate(ep0->context, 0);
+	ep_ctx_write_seq_num(ep0->context, 0);
 
 	deq_ptr = trb_virt_to_phys(ep0, &ep0->transfer_ring[ep0->deq_ptr]);
 
@@ -3295,11 +3300,6 @@
 	unsigned int i;
 	u32 val;
 
-	val = xudc_readl(xudc, SPARAM);
-	val &= ~(SPARAM_ERSTMAX_MASK);
-	val |= SPARAM_ERSTMAX(XUDC_NR_EVENT_RINGS);
-	xudc_writel(xudc, val, SPARAM);
-
 	for (i = 0; i < ARRAY_SIZE(xudc->event_ring); i++) {
 		memset(xudc->event_ring[i], 0, XUDC_EVENT_RING_SIZE *
 		       sizeof(*xudc->event_ring[i]));
@@ -3480,8 +3480,8 @@
 
 static int tegra_xudc_phy_get(struct tegra_xudc *xudc)
 {
-	int err = 0, usb3;
-	unsigned int i;
+	int err = 0, usb3_companion_port;
+	unsigned int i, j;
 
 	xudc->utmi_phy = devm_kcalloc(xudc->dev, xudc->soc->num_phys,
 					   sizeof(*xudc->utmi_phy), GFP_KERNEL);
@@ -3509,7 +3509,7 @@
 		if (IS_ERR(xudc->utmi_phy[i])) {
 			err = PTR_ERR(xudc->utmi_phy[i]);
 			dev_err_probe(xudc->dev, err,
-				      "failed to get usb2-%d PHY\n", i);
+				"failed to get PHY for phy-name usb2-%d\n", i);
 			goto clean_up;
 		} else if (xudc->utmi_phy[i]) {
 			/* Get usb-phy, if utmi phy is available */
@@ -3528,19 +3528,30 @@
 		}
 
 		/* Get USB3 phy */
-		usb3 = tegra_xusb_padctl_get_usb3_companion(xudc->padctl, i);
-		if (usb3 < 0)
+		usb3_companion_port = tegra_xusb_padctl_get_usb3_companion(xudc->padctl, i);
+		if (usb3_companion_port < 0)
 			continue;
 
-		snprintf(phy_name, sizeof(phy_name), "usb3-%d", usb3);
-		xudc->usb3_phy[i] = devm_phy_optional_get(xudc->dev, phy_name);
-		if (IS_ERR(xudc->usb3_phy[i])) {
-			err = PTR_ERR(xudc->usb3_phy[i]);
-			dev_err_probe(xudc->dev, err,
-				      "failed to get usb3-%d PHY\n", usb3);
-			goto clean_up;
-		} else if (xudc->usb3_phy[i])
-			dev_dbg(xudc->dev, "usb3-%d PHY registered", usb3);
+		for (j = 0; j < xudc->soc->num_phys; j++) {
+			snprintf(phy_name, sizeof(phy_name), "usb3-%d", j);
+			xudc->usb3_phy[i] = devm_phy_optional_get(xudc->dev, phy_name);
+			if (IS_ERR(xudc->usb3_phy[i])) {
+				err = PTR_ERR(xudc->usb3_phy[i]);
+				dev_err_probe(xudc->dev, err,
+					"failed to get PHY for phy-name usb3-%d\n", j);
+				goto clean_up;
+			} else if (xudc->usb3_phy[i]) {
+				int usb2_port =
+					tegra_xusb_padctl_get_port_number(xudc->utmi_phy[i]);
+				int usb3_port =
+					tegra_xusb_padctl_get_port_number(xudc->usb3_phy[i]);
+				if (usb3_port == usb3_companion_port) {
+					dev_dbg(xudc->dev, "USB2 port %d is paired with USB3 port %d for device mode port %d\n",
+					 usb2_port, usb3_port, i);
+					break;
+				}
+			}
+		}
 	}
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/trace.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/trace.h
@@ -91,6 +91,11 @@
 	TP_ARGS(g, ret)
 );
 
+DEFINE_EVENT(udc_log_gadget, usb_gadget_set_remote_wakeup,
+	TP_PROTO(struct usb_gadget *g, int ret),
+	TP_ARGS(g, ret)
+);
+
 DEFINE_EVENT(udc_log_gadget, usb_gadget_set_selfpowered,
 	TP_PROTO(struct usb_gadget *g, int ret),
 	TP_ARGS(g, ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/gadget/udc/udc-xilinx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/gadget/udc/udc-xilinx.c
@@ -11,6 +11,7 @@
  * USB peripheral controller (at91_udc.c).
  */
 
+#include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/dma-mapping.h>
@@ -171,6 +172,7 @@
  * @addr: the usb device base address
  * @lock: instance of spinlock
  * @dma_enabled: flag indicating whether the dma is included in the system
+ * @clk: pointer to struct clk
  * @read_fn: function pointer to read device registers
  * @write_fn: function pointer to write to device registers
  */
@@ -188,8 +190,9 @@
 	void __iomem *addr;
 	spinlock_t lock;
 	bool dma_enabled;
+	struct clk *clk;
 
-	unsigned int (*read_fn)(void __iomem *);
+	unsigned int (*read_fn)(void __iomem *reg);
 	void (*write_fn)(void __iomem *, u32, u32);
 };
 
@@ -496,11 +499,13 @@
 		/* Get the Buffer address and copy the transmit data.*/
 		eprambase = (u32 __force *)(udc->addr + ep->rambase);
 		if (ep->is_in) {
-			memcpy(eprambase, bufferptr, bytestosend);
+			memcpy_toio((void __iomem *)eprambase, bufferptr,
+				    bytestosend);
 			udc->write_fn(udc->addr, ep->offset +
 				      XUSB_EP_BUF0COUNT_OFFSET, bufferlen);
 		} else {
-			memcpy(bufferptr, eprambase, bytestosend);
+			memcpy_toio((void __iomem *)bufferptr, eprambase,
+				    bytestosend);
 		}
 		/*
 		 * Enable the buffer for transmission.
@@ -514,11 +519,13 @@
 		eprambase = (u32 __force *)(udc->addr + ep->rambase +
 			     ep->ep_usb.maxpacket);
 		if (ep->is_in) {
-			memcpy(eprambase, bufferptr, bytestosend);
+			memcpy_toio((void __iomem *)eprambase, bufferptr,
+				    bytestosend);
 			udc->write_fn(udc->addr, ep->offset +
 				      XUSB_EP_BUF1COUNT_OFFSET, bufferlen);
 		} else {
-			memcpy(bufferptr, eprambase, bytestosend);
+			memcpy_toio((void __iomem *)bufferptr, eprambase,
+				    bytestosend);
 		}
 		/*
 		 * Enable the buffer for transmission.
@@ -629,7 +636,7 @@
 		dev_dbg(udc->dev, "read %s, %d bytes%s req %p %d/%d\n",
 			ep->ep_usb.name, count, is_short ? "/S" : "", req,
 			req->usb_req.actual, req->usb_req.length);
-		bufferspace -= count;
+
 		/* Completion */
 		if ((req->usb_req.actual == req->usb_req.length) || is_short) {
 			if (udc->dma_enabled && req->usb_req.length)
@@ -1020,7 +1027,7 @@
 			   udc->addr);
 		length = req->usb_req.actual = min_t(u32, length,
 						     EP0_MAX_PACKET);
-		memcpy(corebuf, req->usb_req.buf, length);
+		memcpy_toio((void __iomem *)corebuf, req->usb_req.buf, length);
 		udc->write_fn(udc->addr, XUSB_EP_BUF0COUNT_OFFSET, length);
 		udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1);
 	} else {
@@ -1612,6 +1619,8 @@
 		break;
 	case USB_RECIP_ENDPOINT:
 		epnum = udc->setup.wIndex & USB_ENDPOINT_NUMBER_MASK;
+		if (epnum >= XUSB_MAX_ENDPOINTS)
+			goto stall;
 		target_ep = &udc->ep[epnum];
 		epcfgreg = udc->read_fn(udc->addr + target_ep->offset);
 		halt = epcfgreg & XUSB_EP_CFG_STALL_MASK;
@@ -1679,6 +1688,10 @@
 	case USB_RECIP_ENDPOINT:
 		if (!udc->setup.wValue) {
 			endpoint = udc->setup.wIndex & USB_ENDPOINT_NUMBER_MASK;
+			if (endpoint >= XUSB_MAX_ENDPOINTS) {
+				xudc_ep0_stall(udc);
+				return;
+			}
 			target_ep = &udc->ep[endpoint];
 			outinbit = udc->setup.wIndex & USB_ENDPOINT_DIR_MASK;
 			outinbit = outinbit >> 7;
@@ -1740,7 +1753,7 @@
 
 	/* Load up the chapter 9 command buffer.*/
 	ep0rambase = (u32 __force *) (udc->addr + XUSB_SETUP_PKT_ADDR_OFFSET);
-	memcpy(&setup, ep0rambase, 8);
+	memcpy_toio((void __iomem *)&setup, ep0rambase, 8);
 
 	udc->setup = setup;
 	udc->setup.wValue = cpu_to_le16(setup.wValue);
@@ -1827,7 +1840,7 @@
 			     (ep0->rambase << 2));
 		buffer = req->usb_req.buf + req->usb_req.actual;
 		req->usb_req.actual = req->usb_req.actual + bytes_to_rx;
-		memcpy(buffer, ep0rambase, bytes_to_rx);
+		memcpy_toio((void __iomem *)buffer, ep0rambase, bytes_to_rx);
 
 		if (req->usb_req.length == req->usb_req.actual) {
 			/* Data transfer completed get ready for Status stage */
@@ -1903,7 +1916,7 @@
 				     (ep0->rambase << 2));
 			buffer = req->usb_req.buf + req->usb_req.actual;
 			req->usb_req.actual = req->usb_req.actual + length;
-			memcpy(ep0rambase, buffer, length);
+			memcpy_toio((void __iomem *)ep0rambase, buffer, length);
 		}
 		udc->write_fn(udc->addr, XUSB_EP_BUF0COUNT_OFFSET, count);
 		udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1);
@@ -2092,6 +2105,26 @@
 	udc->gadget.ep0 = &udc->ep[XUSB_EP_NUMBER_ZERO].ep_usb;
 	udc->gadget.name = driver_name;
 
+	udc->clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+	if (IS_ERR(udc->clk)) {
+		if (PTR_ERR(udc->clk) != -ENOENT) {
+			ret = PTR_ERR(udc->clk);
+			goto fail;
+		}
+
+		/*
+		 * Clock framework support is optional, continue on,
+		 * anyways if we don't find a matching clock
+		 */
+		udc->clk = NULL;
+	}
+
+	ret = clk_prepare_enable(udc->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to enable clock.\n");
+		return ret;
+	}
+
 	spin_lock_init(&udc->lock);
 
 	/* Check for IP endianness */
@@ -2147,10 +2180,66 @@
 	struct xusb_udc *udc = platform_get_drvdata(pdev);
 
 	usb_del_gadget_udc(&udc->gadget);
+	clk_disable_unprepare(udc->clk);
 
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int xudc_suspend(struct device *dev)
+{
+	struct xusb_udc *udc;
+	u32 crtlreg;
+	unsigned long flags;
+
+	udc = dev_get_drvdata(dev);
+
+	spin_lock_irqsave(&udc->lock, flags);
+
+	crtlreg = udc->read_fn(udc->addr + XUSB_CONTROL_OFFSET);
+	crtlreg &= ~XUSB_CONTROL_USB_READY_MASK;
+
+	udc->write_fn(udc->addr, XUSB_CONTROL_OFFSET, crtlreg);
+
+	spin_unlock_irqrestore(&udc->lock, flags);
+	if (udc->driver && udc->driver->disconnect)
+		udc->driver->disconnect(&udc->gadget);
+
+	clk_disable(udc->clk);
+
+	return 0;
+}
+
+static int xudc_resume(struct device *dev)
+{
+	struct xusb_udc *udc;
+	u32 crtlreg;
+	unsigned long flags;
+	int ret;
+
+	udc = dev_get_drvdata(dev);
+
+	ret = clk_enable(udc->clk);
+	if (ret < 0)
+		return ret;
+
+	spin_lock_irqsave(&udc->lock, flags);
+
+	crtlreg = udc->read_fn(udc->addr + XUSB_CONTROL_OFFSET);
+	crtlreg |= XUSB_CONTROL_USB_READY_MASK;
+
+	udc->write_fn(udc->addr, XUSB_CONTROL_OFFSET, crtlreg);
+
+	spin_unlock_irqrestore(&udc->lock, flags);
+
+	return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops xudc_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xudc_suspend, xudc_resume)
+};
+
 /* Match table for of_platform binding */
 static const struct of_device_id usb_of_match[] = {
 	{ .compatible = "xlnx,usb2-device-4.00.a", },
@@ -2162,6 +2251,7 @@
 	.driver = {
 		.name = driver_name,
 		.of_match_table = usb_of_match,
+		.pm	= &xudc_pm_ops,
 	},
 	.probe = xudc_probe,
 	.remove = xudc_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/bcma-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/bcma-hcd.c
@@ -285,7 +285,7 @@
 {
 	struct bcma_hcd_device *usb_dev = bcma_get_drvdata(dev);
 
-	if (IS_ERR_OR_NULL(usb_dev->gpio_desc))
+	if (!usb_dev->gpio_desc)
 		return;
 
 	gpiod_set_value(usb_dev->gpio_desc, val);
@@ -406,9 +406,11 @@
 		return -ENOMEM;
 	usb_dev->core = core;
 
-	if (core->dev.of_node)
-		usb_dev->gpio_desc = devm_gpiod_get(&core->dev, "vcc",
-						    GPIOD_OUT_HIGH);
+	usb_dev->gpio_desc = devm_gpiod_get_optional(&core->dev, "vcc",
+						     GPIOD_OUT_HIGH);
+	if (IS_ERR(usb_dev->gpio_desc))
+		return dev_err_probe(&core->dev, PTR_ERR(usb_dev->gpio_desc),
+				     "error obtaining VCC GPIO");
 
 	switch (core->id.id) {
 	case BCMA_CORE_USB20_HOST:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-brcm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-brcm.c
@@ -62,8 +62,12 @@
 	u32 __iomem	*status_reg;
 	unsigned long flags;
 	int retval, irq_disabled = 0;
+	u32 temp;
 
-	status_reg = &ehci->regs->port_status[(wIndex & 0xff) - 1];
+	temp = (wIndex & 0xff) - 1;
+	if (temp >= HCS_N_PORTS_MAX)	/* Avoid index-out-of-bounds warning */
+		temp = 0;
+	status_reg = &ehci->regs->port_status[temp];
 
 	/*
 	 * RESUME is cleared when GetPortStatus() is called 20ms after start
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-fsl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-fsl.c
@@ -29,7 +29,7 @@
 #include "ehci-fsl.h"
 
 #define DRIVER_DESC "Freescale EHCI Host controller driver"
-#define DRV_NAME "ehci-fsl"
+#define DRV_NAME "fsl-ehci"
 
 static struct hc_driver __read_mostly fsl_ehci_hc_driver;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-hcd.c
@@ -635,7 +635,16 @@
 	/* Wait until HC become operational */
 	ehci_readl(ehci, &ehci->regs->command);	/* unblock posted writes */
 	msleep(5);
-	rc = ehci_handshake(ehci, &ehci->regs->status, STS_HALT, 0, 100 * 1000);
+
+	/* For Aspeed, STS_HALT also depends on ASS/PSS status.
+	 * Check CMD_RUN instead.
+	 */
+	if (ehci->is_aspeed)
+		rc = ehci_handshake(ehci, &ehci->regs->command, CMD_RUN,
+				    1, 100 * 1000);
+	else
+		rc = ehci_handshake(ehci, &ehci->regs->status, STS_HALT,
+				    0, 100 * 1000);
 
 	up_write(&ehci_cf_port_reset_rwsem);
 
@@ -746,10 +755,14 @@
 
 	/* normal [4.15.1.2] or error [4.15.1.1] completion */
 	if (likely ((status & (STS_INT|STS_ERR)) != 0)) {
-		if (likely ((status & STS_ERR) == 0))
+		if (likely ((status & STS_ERR) == 0)) {
 			INCR(ehci->stats.normal);
-		else
+		} else {
+			/* Force to check port status */
+			if (ehci->has_ci_pec_bug)
+				status |= STS_PCD;
 			INCR(ehci->stats.error);
+		}
 		bh = 1;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-hub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-hub.c
@@ -674,7 +674,8 @@
 
 		if ((temp & mask) != 0 || test_bit(i, &ehci->port_c_suspend)
 				|| (ehci->reset_done[i] && time_after_eq(
-					jiffies, ehci->reset_done[i]))) {
+					jiffies, ehci->reset_done[i]))
+				|| ehci_has_ci_pec_bug(ehci, temp)) {
 			if (i < 7)
 			    buf [0] |= 1 << (i + 1);
 			else
@@ -874,6 +875,13 @@
 		if (temp & PORT_PEC)
 			status |= USB_PORT_STAT_C_ENABLE << 16;
 
+		if (ehci_has_ci_pec_bug(ehci, temp)) {
+			status |= USB_PORT_STAT_C_ENABLE << 16;
+			ehci_info(ehci,
+				"PE is cleared by HW port:%d PORTSC:%08x\n",
+				wIndex + 1, temp);
+		}
+
 		if ((temp & PORT_OCC) && (!ignore_oc && !ehci->spurious_oc)){
 			status |= USB_PORT_STAT_C_OVERCURRENT << 16;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-pci.c
@@ -21,6 +21,9 @@
 /* defined here to avoid adding to pci_ids.h for single instance use */
 #define PCI_DEVICE_ID_INTEL_CE4100_USB	0x2e70
 
+#define PCI_VENDOR_ID_ASPEED		0x1a03
+#define PCI_DEVICE_ID_ASPEED_EHCI	0x2603
+
 /*-------------------------------------------------------------------------*/
 #define PCI_DEVICE_ID_INTEL_QUARK_X1000_SOC		0x0939
 static inline bool is_intel_quark_x1000(struct pci_dev *pdev)
@@ -222,6 +225,12 @@
 			ehci->has_synopsys_hc_bug = 1;
 		}
 		break;
+	case PCI_VENDOR_ID_ASPEED:
+		if (pdev->device == PCI_DEVICE_ID_ASPEED_EHCI) {
+			ehci_info(ehci, "applying Aspeed HC workaround\n");
+			ehci->is_aspeed = 1;
+		}
+		break;
 	}
 
 	/* optional debug port, normally in the first BAR */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-platform.c
@@ -297,6 +297,12 @@
 					  "has-transaction-translator"))
 			hcd->has_tt = 1;
 
+		if (of_device_is_compatible(dev->dev.of_node,
+					    "aspeed,ast2500-ehci") ||
+		    of_device_is_compatible(dev->dev.of_node,
+					    "aspeed,ast2600-ehci"))
+			ehci->is_aspeed = 1;
+
 		if (soc_device_match(quirk_poll_match))
 			priv->quirk_poll = true;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-ppc-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-ppc-of.c
@@ -148,6 +148,7 @@
 		} else {
 			ehci->has_amcc_usb23 = 1;
 		}
+		of_node_put(np);
 	}
 
 	if (of_get_property(dn, "big-endian", NULL)) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-sh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-sh.c
@@ -120,8 +120,12 @@
 	if (IS_ERR(priv->iclk))
 		priv->iclk = NULL;
 
-	clk_enable(priv->fclk);
-	clk_enable(priv->iclk);
+	ret = clk_enable(priv->fclk);
+	if (ret)
+		goto fail_request_resource;
+	ret = clk_enable(priv->iclk);
+	if (ret)
+		goto fail_iclk;
 
 	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (ret != 0) {
@@ -137,6 +141,7 @@
 
 fail_add_hcd:
 	clk_disable(priv->iclk);
+fail_iclk:
 	clk_disable(priv->fclk);
 
 fail_request_resource:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-spear.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-spear.c
@@ -108,7 +108,9 @@
 	/* registers start at offset 0x0 */
 	hcd_to_ehci(hcd)->caps = hcd->regs;
 
-	clk_prepare_enable(sehci->clk);
+	retval = clk_prepare_enable(sehci->clk);
+	if (retval)
+		goto err_put_hcd;
 	retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (retval)
 		goto err_stop_ehci;
@@ -133,8 +135,7 @@
 
 	usb_remove_hcd(hcd);
 
-	if (sehci->clk)
-		clk_disable_unprepare(sehci->clk);
+	clk_disable_unprepare(sehci->clk);
 	usb_put_hcd(hcd);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci-xilinx-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci-xilinx-of.c
@@ -32,6 +32,8 @@
  * There are cases when the host controller fails to enable the port due to,
  * for example, insufficient power that can be supplied to the device from
  * the USB bus. In those cases, the messages printed here are not helpful.
+ *
+ * Return: Always return 0
  */
 static int ehci_xilinx_port_handed_over(struct usb_hcd *hcd, int portnum)
 {
@@ -46,11 +48,9 @@
 		dev_warn(hcd->self.controller,
 			"Maybe your device is not a high speed device?\n");
 		dev_warn(hcd->self.controller,
-			"The USB host controller does not support full speed "
-			"nor low speed devices\n");
+			"USB host controller doesn't support FS/LS devices\n");
 		dev_warn(hcd->self.controller,
-			"You can reconfigure the host controller to have "
-			"full speed support\n");
+			"You can reconfigure host controller to support FS\n");
 	}
 
 	return 0;
@@ -112,6 +112,8 @@
  * host controller. Because the Xilinx USB host controller can be configured
  * as HS only or HS/FS only, it checks the configuration in the device tree
  * entry, and sets an appropriate value for hcd->has_tt.
+ *
+ * Return: zero on success, 'rv' value on failure
  */
 static int ehci_hcd_xilinx_of_probe(struct platform_device *op)
 {
@@ -196,6 +198,8 @@
  *
  * Remove the hcd structure, and release resources that has been requested
  * during probe.
+ *
+ * Return: Always return 0
  */
 static int ehci_hcd_xilinx_of_remove(struct platform_device *op)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ehci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ehci.h
@@ -207,6 +207,7 @@
 	unsigned		has_fsl_port_bug:1; /* FreeScale */
 	unsigned		has_fsl_hs_errata:1;	/* Freescale HS quirk */
 	unsigned		has_fsl_susp_errata:1;	/* NXP SUSP quirk */
+	unsigned		has_ci_pec_bug:1;	/* ChipIdea PEC bug */
 	unsigned		big_endian_mmio:1;
 	unsigned		big_endian_desc:1;
 	unsigned		big_endian_capbase:1;
@@ -219,6 +220,7 @@
 	unsigned		need_oc_pp_cycle:1; /* MPC834X port power */
 	unsigned		imx28_write_fix:1; /* For Freescale i.MX28 */
 	unsigned		spurious_oc:1;
+	unsigned		is_aspeed:1;
 
 	/* required for usb32 quirk */
 	#define OHCI_CTRL_HCFS          (3 << 6)
@@ -706,6 +708,15 @@
 #define ehci_has_fsl_susp_errata(e)	((e)->has_fsl_susp_errata)
 
 /*
+ * Some Freescale/NXP processors using ChipIdea IP have a bug in which
+ * disabling the port (PE is cleared) does not cause PEC to be asserted
+ * when frame babble is detected.
+ */
+#define ehci_has_ci_pec_bug(e, portsc) \
+	((e)->has_ci_pec_bug && ((e)->command & CMD_PSE) \
+	 && !(portsc & PORT_PEC) && !(portsc & PORT_PE))
+
+/*
  * While most USB host controllers implement their registers in
  * little-endian format, a minority (celleb companion chip) implement
  * them in big endian format.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/fotg210-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/fotg210-hcd.c
@@ -429,8 +429,6 @@
 			temp = size;
 		size -= temp;
 		next += temp;
-		if (temp == size)
-			goto done;
 	}
 
 	temp = snprintf(next, size, "\n");
@@ -440,7 +438,6 @@
 	size -= temp;
 	next += temp;
 
-done:
 	*sizep = size;
 	*nextp = next;
 }
@@ -862,7 +859,7 @@
 {
 	struct usb_bus *bus = &fotg210_to_hcd(fotg210)->self;
 
-	debugfs_remove(debugfs_lookup(bus->bus_name, fotg210_debug_root));
+	debugfs_lookup_and_remove(bus->bus_name, fotg210_debug_root);
 }
 
 /* handshake - spin reading hc until handshake completes or fails
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/isp116x-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/isp116x-hcd.c
@@ -1206,7 +1206,7 @@
 
 static void remove_debug_file(struct isp116x *isp116x)
 {
-	debugfs_remove(debugfs_lookup(hcd_name, usb_debug_root));
+	debugfs_lookup_and_remove(hcd_name, usb_debug_root);
 }
 
 #else
@@ -1541,10 +1541,12 @@
 
 	iounmap(isp116x->data_reg);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	release_mem_region(res->start, 2);
+	if (res)
+		release_mem_region(res->start, 2);
 	iounmap(isp116x->addr_reg);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(res->start, 2);
+	if (res)
+		release_mem_region(res->start, 2);
 
 	usb_put_hcd(hcd);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/isp1362-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/isp1362-hcd.c
@@ -2170,7 +2170,7 @@
 
 static void remove_debug_file(struct isp1362_hcd *isp1362_hcd)
 {
-	debugfs_remove(debugfs_lookup("isp1362", usb_debug_root));
+	debugfs_lookup_and_remove("isp1362", usb_debug_root);
 }
 
 /*-------------------------------------------------------------------------*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/max3421-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/max3421-hcd.c
@@ -125,8 +125,6 @@
 
 	struct task_struct *spi_thread;
 
-	struct max3421_hcd *next;
-
 	enum max3421_rh_state rh_state;
 	/* lower 16 bits contain port status, upper 16 bits the change mask: */
 	u32 port_status;
@@ -174,8 +172,6 @@
 	u8 retransmit;			/* packet needs retransmission */
 };
 
-static struct max3421_hcd *max3421_hcd_list;
-
 #define MAX3421_FIFO_SIZE	64
 
 #define MAX3421_SPI_DIR_RD	0	/* read register from MAX3421 */
@@ -789,11 +785,17 @@
 				retval = 1;
 				dev_dbg(&spi->dev, "%s: URB %p unlinked=%d",
 					__func__, urb, urb->unlinked);
-				usb_hcd_unlink_urb_from_ep(hcd, urb);
-				spin_unlock_irqrestore(&max3421_hcd->lock,
-						       flags);
-				usb_hcd_giveback_urb(hcd, urb, 0);
-				spin_lock_irqsave(&max3421_hcd->lock, flags);
+				if (urb == max3421_hcd->curr_urb) {
+					max3421_hcd->urb_done = 1;
+					max3421_hcd->hien &= ~(BIT(MAX3421_HI_HXFRDN_BIT) |
+							       BIT(MAX3421_HI_RCVDAV_BIT));
+				} else {
+					usb_hcd_unlink_urb_from_ep(hcd, urb);
+					spin_unlock_irqrestore(&max3421_hcd->lock,
+							       flags);
+					usb_hcd_giveback_urb(hcd, urb, 0);
+					spin_lock_irqsave(&max3421_hcd->lock, flags);
+				}
 			}
 		}
 	}
@@ -1440,7 +1442,7 @@
 			 * use spi_wr_buf().
 			 */
 			for (i = 0; i < ARRAY_SIZE(max3421_hcd->iopins); ++i) {
-				u8 val = spi_rd8(hcd, MAX3421_REG_IOPINS1);
+				u8 val = spi_rd8(hcd, MAX3421_REG_IOPINS1 + i);
 
 				val = ((val & 0xf0) |
 				       (max3421_hcd->iopins[i] & 0x0f));
@@ -1882,9 +1884,8 @@
 	}
 	set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 	max3421_hcd = hcd_to_max3421(hcd);
-	max3421_hcd->next = max3421_hcd_list;
-	max3421_hcd_list = max3421_hcd;
 	INIT_LIST_HEAD(&max3421_hcd->ep_list);
+	spi_set_drvdata(spi, max3421_hcd);
 
 	max3421_hcd->tx = kmalloc(sizeof(*max3421_hcd->tx), GFP_KERNEL);
 	if (!max3421_hcd->tx)
@@ -1934,28 +1935,18 @@
 static int
 max3421_remove(struct spi_device *spi)
 {
-	struct max3421_hcd *max3421_hcd = NULL, **prev;
-	struct usb_hcd *hcd = NULL;
+	struct max3421_hcd *max3421_hcd;
+	struct usb_hcd *hcd;
 	unsigned long flags;
 
-	for (prev = &max3421_hcd_list; *prev; prev = &(*prev)->next) {
-		max3421_hcd = *prev;
-		hcd = max3421_to_hcd(max3421_hcd);
-		if (hcd->self.controller == &spi->dev)
-			break;
-	}
-	if (!max3421_hcd) {
-		dev_err(&spi->dev, "no MAX3421 HCD found for SPI device %p\n",
-			spi);
-		return -ENODEV;
-	}
+	max3421_hcd = spi_get_drvdata(spi);
+	hcd = max3421_to_hcd(max3421_hcd);
 
 	usb_remove_hcd(hcd);
 
 	spin_lock_irqsave(&max3421_hcd->lock, flags);
 
 	kthread_stop(max3421_hcd->spi_thread);
-	*prev = max3421_hcd->next;
 
 	spin_unlock_irqrestore(&max3421_hcd->lock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ohci-at91.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ohci-at91.c
@@ -652,7 +652,13 @@
 	else
 		at91_start_clock(ohci_at91);
 
-	ohci_resume(hcd, false);
+	/*
+	 * According to the comment in ohci_hcd_at91_drv_suspend()
+	 * we need to do a reset if the 48Mhz clock was stopped,
+	 * that is, if ohci_at91->wakeup is clear. Tell ohci_resume()
+	 * to reset in this case by setting its "hibernated" flag.
+	 */
+	ohci_resume(hcd, !ohci_at91->wakeup);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ohci-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ohci-hcd.c
@@ -890,6 +890,7 @@
 	/* Check for an all 1's result which is a typical consequence
 	 * of dead, unclocked, or unplugged (CardBus...) devices
 	 */
+again:
 	if (ints == ~(u32)0) {
 		ohci->rh_state = OHCI_RH_HALTED;
 		ohci_dbg (ohci, "device removed!\n");
@@ -984,6 +985,13 @@
 	}
 	spin_unlock(&ohci->lock);
 
+	/* repeat until all enabled interrupts are handled */
+	if (ohci->rh_state != OHCI_RH_HALTED) {
+		ints = ohci_readl(ohci, &regs->intrstatus);
+		if (ints && (ints & ohci_readl(ohci, &regs->intrenable)))
+			goto again;
+	}
+
 	return IRQ_HANDLED;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ohci-nxp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ohci-nxp.c
@@ -164,6 +164,7 @@
 	}
 
 	isp1301_i2c_client = isp1301_get_client(isp1301_node);
+	of_node_put(isp1301_node);
 	if (!isp1301_i2c_client)
 		return -EPROBE_DEFER;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ohci-ppc-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ohci-ppc-of.c
@@ -169,6 +169,7 @@
 				release_mem_region(res.start, 0x4);
 		} else
 			pr_debug("%s: cannot get ehci offset from fdt\n", __FILE__);
+		of_node_put(np);
 	}
 
 	irq_dispose_mapping(irq);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/ohci-tmio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/ohci-tmio.c
@@ -199,7 +199,7 @@
 	if (usb_disabled())
 		return -ENODEV;
 
-	if (!cell)
+	if (!cell || !regs || !config || !sram)
 		return -EINVAL;
 
 	if (irq < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/oxu210hp-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/oxu210hp-hcd.c
@@ -3909,8 +3909,10 @@
 		}
 	}
 
+	spin_unlock_irq(&oxu->lock);
 	/* turn off now-idle HC */
 	del_timer_sync(&oxu->watchdog);
+	spin_lock_irq(&oxu->lock);
 	ehci_halt(oxu);
 	hcd->state = HC_STATE_SUSPENDED;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/pci-quirks.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/pci-quirks.c
@@ -948,6 +948,15 @@
 	 * booting from USB disk or using a usb keyboard
 	 */
 	hcc_params = readl(base + EHCI_HCC_PARAMS);
+
+	/* LS7A EHCI controller doesn't have extended capabilities, the
+	 * EECP (EHCI Extended Capabilities Pointer) field of HCCPARAMS
+	 * register should be 0x0 but it reads as 0xa0.  So clear it to
+	 * avoid error messages on boot.
+	 */
+	if (pdev->vendor == PCI_VENDOR_ID_LOONGSON && pdev->device == 0x7a14)
+		hcc_params &= ~(0xffL << 8);
+
 	offset = (hcc_params >> 8) & 0xff;
 	while (offset && --count) {
 		pci_read_config_dword(pdev, offset, &cap);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/sl811-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/sl811-hcd.c
@@ -585,6 +585,7 @@
 		finish_request(sl811, ep, urb, urbstat);
 }
 
+#ifdef QUIRK2
 static inline u8 checkdone(struct sl811 *sl811)
 {
 	u8	ctl;
@@ -616,6 +617,7 @@
 #endif
 	return irqstat;
 }
+#endif
 
 static irqreturn_t sl811h_irq(struct usb_hcd *hcd)
 {
@@ -1501,7 +1503,7 @@
 
 static void remove_debug_file(struct sl811 *sl811)
 {
-	debugfs_remove(debugfs_lookup("sl811h", usb_debug_root));
+	debugfs_lookup_and_remove("sl811h", usb_debug_root);
 }
 
 /*-------------------------------------------------------------------------*/
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/uhci-hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/uhci-hcd.c
@@ -536,8 +536,8 @@
 	uhci->is_initialized = 0;
 	spin_unlock_irq(&uhci->lock);
 
-	debugfs_remove(debugfs_lookup(uhci_to_hcd(uhci)->self.bus_name,
-				      uhci_debugfs_root));
+	debugfs_lookup_and_remove(uhci_to_hcd(uhci)->self.bus_name,
+				  uhci_debugfs_root);
 
 	for (i = 0; i < UHCI_NUM_SKELQH; i++)
 		uhci_free_qh(uhci, uhci->skelqh[i]);
@@ -700,7 +700,7 @@
 			uhci->frame, uhci->frame_dma_handle);
 
 err_alloc_frame:
-	debugfs_remove(debugfs_lookup(hcd->self.bus_name, uhci_debugfs_root));
+	debugfs_lookup_and_remove(hcd->self.bus_name, uhci_debugfs_root);
 
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/uhci-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/uhci-pci.c
@@ -119,11 +119,13 @@
 
 	uhci->rh_numports = uhci_count_ports(hcd);
 
-	/* Intel controllers report the OverCurrent bit active on.
-	 * VIA controllers report it active off, so we'll adjust the
-	 * bit value.  (It's not standardized in the UHCI spec.)
+	/*
+	 * Intel controllers report the OverCurrent bit active on.  VIA
+	 * and ZHAOXIN controllers report it active off, so we'll adjust
+	 * the bit value.  (It's not standardized in the UHCI spec.)
 	 */
-	if (to_pci_dev(uhci_dev(uhci))->vendor == PCI_VENDOR_ID_VIA)
+	if (to_pci_dev(uhci_dev(uhci))->vendor == PCI_VENDOR_ID_VIA ||
+			to_pci_dev(uhci_dev(uhci))->vendor == PCI_VENDOR_ID_ZHAOXIN)
 		uhci->oc_low = 1;
 
 	/* HP's server management chip requires a longer port reset delay. */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/uhci-platform.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/uhci-platform.c
@@ -113,7 +113,8 @@
 				num_ports);
 		}
 		if (of_device_is_compatible(np, "aspeed,ast2400-uhci") ||
-		    of_device_is_compatible(np, "aspeed,ast2500-uhci")) {
+		    of_device_is_compatible(np, "aspeed,ast2500-uhci") ||
+		    of_device_is_compatible(np, "aspeed,ast2600-uhci")) {
 			uhci->is_aspeed = 1;
 			dev_info(&pdev->dev,
 				 "Enabled Aspeed implementation workarounds\n");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-caps.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-caps.h
@@ -0,0 +1,85 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* hc_capbase bitmasks */
+/* bits 7:0 - how long is the Capabilities register */
+#define HC_LENGTH(p)		XHCI_HC_LENGTH(p)
+/* bits 31:16	*/
+#define HC_VERSION(p)		(((p) >> 16) & 0xffff)
+
+/* HCSPARAMS1 - hcs_params1 - bitmasks */
+/* bits 0:7, Max Device Slots */
+#define HCS_MAX_SLOTS(p)	(((p) >> 0) & 0xff)
+#define HCS_SLOTS_MASK		0xff
+/* bits 8:18, Max Interrupters */
+#define HCS_MAX_INTRS(p)	(((p) >> 8) & 0x7ff)
+/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
+#define HCS_MAX_PORTS(p)	(((p) >> 24) & 0x7f)
+
+/* HCSPARAMS2 - hcs_params2 - bitmasks */
+/* bits 0:3, frames or uframes that SW needs to queue transactions
+ * ahead of the HW to meet periodic deadlines */
+#define HCS_IST(p)		(((p) >> 0) & 0xf)
+/* bits 4:7, max number of Event Ring segments */
+#define HCS_ERST_MAX(p)		(((p) >> 4) & 0xf)
+/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
+/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
+/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
+#define HCS_MAX_SCRATCHPAD(p)   ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
+
+/* HCSPARAMS3 - hcs_params3 - bitmasks */
+/* bits 0:7, Max U1 to U0 latency for the roothub ports */
+#define HCS_U1_LATENCY(p)	(((p) >> 0) & 0xff)
+/* bits 16:31, Max U2 to U0 latency for the roothub ports */
+#define HCS_U2_LATENCY(p)	(((p) >> 16) & 0xffff)
+
+/* HCCPARAMS - hcc_params - bitmasks */
+/* true: HC can use 64-bit address pointers */
+#define HCC_64BIT_ADDR(p)	((p) & (1 << 0))
+/* true: HC can do bandwidth negotiation */
+#define HCC_BANDWIDTH_NEG(p)	((p) & (1 << 1))
+/* true: HC uses 64-byte Device Context structures
+ * FIXME 64-byte context structures aren't supported yet.
+ */
+#define HCC_64BYTE_CONTEXT(p)	((p) & (1 << 2))
+/* true: HC has port power switches */
+#define HCC_PPC(p)		((p) & (1 << 3))
+/* true: HC has port indicators */
+#define HCS_INDICATOR(p)	((p) & (1 << 4))
+/* true: HC has Light HC Reset Capability */
+#define HCC_LIGHT_RESET(p)	((p) & (1 << 5))
+/* true: HC supports latency tolerance messaging */
+#define HCC_LTC(p)		((p) & (1 << 6))
+/* true: no secondary Stream ID Support */
+#define HCC_NSS(p)		((p) & (1 << 7))
+/* true: HC supports Stopped - Short Packet */
+#define HCC_SPC(p)		((p) & (1 << 9))
+/* true: HC has Contiguous Frame ID Capability */
+#define HCC_CFC(p)		((p) & (1 << 11))
+/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
+#define HCC_MAX_PSA(p)		(1 << ((((p) >> 12) & 0xf) + 1))
+/* Extended Capabilities pointer from PCI base - section 5.3.6 */
+#define HCC_EXT_CAPS(p)		XHCI_HCC_EXT_CAPS(p)
+
+#define CTX_SIZE(_hcc)		(HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
+
+/* db_off bitmask - bits 0:1 reserved */
+#define	DBOFF_MASK	(~0x3)
+
+/* run_regs_off bitmask - bits 0:4 reserved */
+#define	RTSOFF_MASK	(~0x1f)
+
+/* HCCPARAMS2 - hcc_params2 - bitmasks */
+/* true: HC supports U3 entry Capability */
+#define	HCC2_U3C(p)		((p) & (1 << 0))
+/* true: HC supports Configure endpoint command Max exit latency too large */
+#define	HCC2_CMC(p)		((p) & (1 << 1))
+/* true: HC supports Force Save context Capability */
+#define	HCC2_FSC(p)		((p) & (1 << 2))
+/* true: HC supports Compliance Transition Capability */
+#define	HCC2_CTC(p)		((p) & (1 << 3))
+/* true: HC support Large ESIT payload Capability > 48k */
+#define	HCC2_LEC(p)		((p) & (1 << 4))
+/* true: HC support Configuration Information Capability */
+#define	HCC2_CIC(p)		((p) & (1 << 5))
+/* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
+#define	HCC2_ETC(p)		((p) & (1 << 6))
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-dbgcap.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-dbgcap.c
@@ -158,16 +158,18 @@
 	spin_lock(&dbc->lock);
 }
 
-static void xhci_dbc_flush_single_request(struct dbc_request *req)
+static void trb_to_noop(union xhci_trb *trb)
 {
-	union xhci_trb	*trb = req->trb;
-
 	trb->generic.field[0]	= 0;
 	trb->generic.field[1]	= 0;
 	trb->generic.field[2]	= 0;
 	trb->generic.field[3]	&= cpu_to_le32(TRB_CYCLE);
 	trb->generic.field[3]	|= cpu_to_le32(TRB_TYPE(TRB_TR_NOOP));
+}
 
+static void xhci_dbc_flush_single_request(struct dbc_request *req)
+{
+	trb_to_noop(req->trb);
 	xhci_dbc_giveback(req, -ESHUTDOWN);
 }
 
@@ -637,7 +639,6 @@
 	case DS_DISABLED:
 		return;
 	case DS_CONFIGURED:
-	case DS_STALLED:
 		if (dbc->driver->disconnect)
 			dbc->driver->disconnect(dbc);
 		break;
@@ -658,6 +659,23 @@
 }
 
 static void
+handle_ep_halt_changes(struct xhci_dbc *dbc, struct dbc_ep *dep, bool halted)
+{
+	if (halted) {
+		dev_info(dbc->dev, "DbC Endpoint halted\n");
+		dep->halted = 1;
+
+	} else if (dep->halted) {
+		dev_info(dbc->dev, "DbC Endpoint halt cleared\n");
+		dep->halted = 0;
+
+		if (!list_empty(&dep->list_pending))
+			writel(DBC_DOOR_BELL_TARGET(dep->direction),
+			       &dbc->regs->doorbell);
+	}
+}
+
+static void
 dbc_handle_port_status(struct xhci_dbc *dbc, union xhci_trb *event)
 {
 	u32			portsc;
@@ -685,6 +703,7 @@
 	struct xhci_ring	*ring;
 	int			ep_id;
 	int			status;
+	struct xhci_ep_ctx	*ep_ctx;
 	u32			comp_code;
 	size_t			remain_length;
 	struct dbc_request	*req = NULL, *r;
@@ -694,8 +713,30 @@
 	ep_id		= TRB_TO_EP_ID(le32_to_cpu(event->generic.field[3]));
 	dep		= (ep_id == EPID_OUT) ?
 				get_out_ep(dbc) : get_in_ep(dbc);
+	ep_ctx		= (ep_id == EPID_OUT) ?
+				dbc_bulkout_ctx(dbc) : dbc_bulkin_ctx(dbc);
 	ring		= dep->ring;
 
+	/* Match the pending request: */
+	list_for_each_entry(r, &dep->list_pending, list_pending) {
+		if (r->trb_dma == event->trans_event.buffer) {
+			req = r;
+			break;
+		}
+		if (r->status == -COMP_STALL_ERROR) {
+			dev_warn(dbc->dev, "Give back stale stalled req\n");
+			ring->num_trbs_free++;
+			xhci_dbc_giveback(r, 0);
+		}
+	}
+
+	if (!req) {
+		dev_warn(dbc->dev, "no matched request\n");
+		return;
+	}
+
+	trace_xhci_dbc_handle_transfer(ring, &req->trb->generic);
+
 	switch (comp_code) {
 	case COMP_SUCCESS:
 		remain_length = 0;
@@ -706,31 +747,49 @@
 	case COMP_TRB_ERROR:
 	case COMP_BABBLE_DETECTED_ERROR:
 	case COMP_USB_TRANSACTION_ERROR:
-	case COMP_STALL_ERROR:
 		dev_warn(dbc->dev, "tx error %d detected\n", comp_code);
 		status = -comp_code;
 		break;
+	case COMP_STALL_ERROR:
+		dev_warn(dbc->dev, "Stall error at bulk TRB %llx, remaining %zu, ep deq %llx\n",
+			 event->trans_event.buffer, remain_length, ep_ctx->deq);
+		status = 0;
+		dep->halted = 1;
+
+		/*
+		 * xHC DbC may trigger a STALL bulk xfer event when host sends a
+		 * ClearFeature(ENDPOINT_HALT) request even if there wasn't an
+		 * active bulk transfer.
+		 *
+		 * Don't give back this transfer request as hardware will later
+		 * start processing TRBs starting from this 'STALLED' TRB,
+		 * causing TRBs and requests to be out of sync.
+		 *
+		 * If STALL event shows some bytes were transferred then assume
+		 * it's an actual transfer issue and give back the request.
+		 * In this case mark the TRB as No-Op to avoid hw from using the
+		 * TRB again.
+		 */
+
+		if ((ep_ctx->deq & ~TRB_CYCLE) == event->trans_event.buffer) {
+			dev_dbg(dbc->dev, "Ep stopped on Stalled TRB\n");
+			if (remain_length == req->length) {
+				dev_dbg(dbc->dev, "Spurious stall event, keep req\n");
+				req->status = -COMP_STALL_ERROR;
+				req->actual = 0;
+				return;
+			}
+			dev_dbg(dbc->dev, "Give back stalled req, but turn TRB to No-op\n");
+			trb_to_noop(req->trb);
+		}
+		break;
+
 	default:
 		dev_err(dbc->dev, "unknown tx error %d\n", comp_code);
 		status = -comp_code;
 		break;
 	}
 
-	/* Match the pending request: */
-	list_for_each_entry(r, &dep->list_pending, list_pending) {
-		if (r->trb_dma == event->trans_event.buffer) {
-			req = r;
-			break;
-		}
-	}
-
-	if (!req) {
-		dev_warn(dbc->dev, "no matched request\n");
-		return;
-	}
-
-	trace_xhci_dbc_handle_transfer(ring, &req->trb->generic);
-
 	ring->num_trbs_free++;
 	req->actual = req->length - remain_length;
 	xhci_dbc_giveback(req, status);
@@ -750,7 +809,6 @@
 static enum evtreturn xhci_dbc_do_handle_events(struct xhci_dbc *dbc)
 {
 	dma_addr_t		deq;
-	struct dbc_ep		*dep;
 	union xhci_trb		*evt;
 	u32			ctrl, portsc;
 	bool			update_erdp = false;
@@ -802,43 +860,17 @@
 			return EVT_DISC;
 		}
 
-		/* Handle endpoint stall event: */
+		/* Check and handle changes in endpoint halt status */
 		ctrl = readl(&dbc->regs->control);
-		if ((ctrl & DBC_CTRL_HALT_IN_TR) ||
-		    (ctrl & DBC_CTRL_HALT_OUT_TR)) {
-			dev_info(dbc->dev, "DbC Endpoint stall\n");
-			dbc->state = DS_STALLED;
-
-			if (ctrl & DBC_CTRL_HALT_IN_TR) {
-				dep = get_in_ep(dbc);
-				xhci_dbc_flush_endpoint_requests(dep);
-			}
-
-			if (ctrl & DBC_CTRL_HALT_OUT_TR) {
-				dep = get_out_ep(dbc);
-				xhci_dbc_flush_endpoint_requests(dep);
-			}
-
-			return EVT_DONE;
-		}
+		handle_ep_halt_changes(dbc, get_in_ep(dbc), ctrl & DBC_CTRL_HALT_IN_TR);
+		handle_ep_halt_changes(dbc, get_out_ep(dbc), ctrl & DBC_CTRL_HALT_OUT_TR);
 
 		/* Clear DbC run change bit: */
 		if (ctrl & DBC_CTRL_DBC_RUN_CHANGE) {
 			writel(ctrl, &dbc->regs->control);
 			ctrl = readl(&dbc->regs->control);
 		}
-
 		break;
-	case DS_STALLED:
-		ctrl = readl(&dbc->regs->control);
-		if (!(ctrl & DBC_CTRL_HALT_IN_TR) &&
-		    !(ctrl & DBC_CTRL_HALT_OUT_TR) &&
-		    (ctrl & DBC_CTRL_DBC_RUN)) {
-			dbc->state = DS_CONFIGURED;
-			break;
-		}
-
-		return EVT_DONE;
 	default:
 		dev_err(dbc->dev, "Unknown DbC state %d\n", dbc->state);
 		break;
@@ -914,59 +946,6 @@
 	mod_delayed_work(system_wq, &dbc->event_work, 1);
 }
 
-static void xhci_do_dbc_exit(struct xhci_hcd *xhci)
-{
-	unsigned long		flags;
-
-	spin_lock_irqsave(&xhci->lock, flags);
-	kfree(xhci->dbc);
-	xhci->dbc = NULL;
-	spin_unlock_irqrestore(&xhci->lock, flags);
-}
-
-static int xhci_do_dbc_init(struct xhci_hcd *xhci)
-{
-	u32			reg;
-	struct xhci_dbc		*dbc;
-	unsigned long		flags;
-	void __iomem		*base;
-	int			dbc_cap_offs;
-
-	base = &xhci->cap_regs->hc_capbase;
-	dbc_cap_offs = xhci_find_next_ext_cap(base, 0, XHCI_EXT_CAPS_DEBUG);
-	if (!dbc_cap_offs)
-		return -ENODEV;
-
-	dbc = kzalloc(sizeof(*dbc), GFP_KERNEL);
-	if (!dbc)
-		return -ENOMEM;
-
-	dbc->regs = base + dbc_cap_offs;
-
-	/* We will avoid using DbC in xhci driver if it's in use. */
-	reg = readl(&dbc->regs->control);
-	if (reg & DBC_CTRL_DBC_ENABLE) {
-		kfree(dbc);
-		return -EBUSY;
-	}
-
-	spin_lock_irqsave(&xhci->lock, flags);
-	if (xhci->dbc) {
-		spin_unlock_irqrestore(&xhci->lock, flags);
-		kfree(dbc);
-		return -EBUSY;
-	}
-	xhci->dbc = dbc;
-	spin_unlock_irqrestore(&xhci->lock, flags);
-
-	dbc->xhci = xhci;
-	dbc->dev = xhci_to_hcd(xhci)->self.sysdev;
-	INIT_DELAYED_WORK(&dbc->event_work, xhci_dbc_handle_events);
-	spin_lock_init(&dbc->lock);
-
-	return 0;
-}
-
 static ssize_t dbc_show(struct device *dev,
 			struct device_attribute *attr,
 			char *buf)
@@ -994,9 +973,6 @@
 	case DS_CONFIGURED:
 		p = "configured";
 		break;
-	case DS_STALLED:
-		p = "stalled";
-		break;
 	default:
 		p = "unknown";
 	}
@@ -1026,44 +1002,86 @@
 
 static DEVICE_ATTR_RW(dbc);
 
-int xhci_dbc_init(struct xhci_hcd *xhci)
+struct xhci_dbc *
+xhci_alloc_dbc(struct device *dev, void __iomem *base, const struct dbc_driver *driver)
 {
+	struct xhci_dbc		*dbc;
 	int			ret;
-	struct device		*dev = xhci_to_hcd(xhci)->self.controller;
 
-	ret = xhci_do_dbc_init(xhci);
-	if (ret)
-		goto init_err3;
+	dbc = kzalloc(sizeof(*dbc), GFP_KERNEL);
+	if (!dbc)
+		return NULL;
 
-	ret = xhci_dbc_tty_probe(xhci);
-	if (ret)
-		goto init_err2;
+	dbc->regs = base;
+	dbc->dev = dev;
+	dbc->driver = driver;
+
+	if (readl(&dbc->regs->control) & DBC_CTRL_DBC_ENABLE)
+		goto err;
+
+	INIT_DELAYED_WORK(&dbc->event_work, xhci_dbc_handle_events);
+	spin_lock_init(&dbc->lock);
 
 	ret = device_create_file(dev, &dev_attr_dbc);
 	if (ret)
-		goto init_err1;
+		goto err;
 
-	return 0;
+	return dbc;
+err:
+	kfree(dbc);
+	return NULL;
+}
+
+/* undo what xhci_alloc_dbc() did */
+void xhci_dbc_remove(struct xhci_dbc *dbc)
+{
+	if (!dbc)
+		return;
+	/* stop hw, stop wq and call dbc->ops->stop() */
+	xhci_dbc_stop(dbc);
+
+	/* remove sysfs files */
+	device_remove_file(dbc->dev, &dev_attr_dbc);
+
+	kfree(dbc);
+}
+
+
+int xhci_create_dbc_dev(struct xhci_hcd *xhci)
+{
+	struct device		*dev;
+	void __iomem		*base;
+	int			ret;
+	int			dbc_cap_offs;
+
+	/* create all parameters needed resembling a dbc device */
+	dev = xhci_to_hcd(xhci)->self.controller;
+	base = &xhci->cap_regs->hc_capbase;
+
+	dbc_cap_offs = xhci_find_next_ext_cap(base, 0, XHCI_EXT_CAPS_DEBUG);
+	if (!dbc_cap_offs)
+		return -ENODEV;
+
+	/* already allocated and in use */
+	if (xhci->dbc)
+		return -EBUSY;
+
+	ret = xhci_dbc_tty_probe(dev, base + dbc_cap_offs, xhci);
 
-init_err1:
-	xhci_dbc_tty_remove(xhci->dbc);
-init_err2:
-	xhci_do_dbc_exit(xhci);
-init_err3:
 	return ret;
 }
 
-void xhci_dbc_exit(struct xhci_hcd *xhci)
+void xhci_remove_dbc_dev(struct xhci_hcd *xhci)
 {
-	struct device		*dev = xhci_to_hcd(xhci)->self.controller;
+	unsigned long		flags;
 
 	if (!xhci->dbc)
 		return;
 
-	device_remove_file(dev, &dev_attr_dbc);
 	xhci_dbc_tty_remove(xhci->dbc);
-	xhci_dbc_stop(xhci->dbc);
-	xhci_do_dbc_exit(xhci);
+	spin_lock_irqsave(&xhci->lock, flags);
+	xhci->dbc = NULL;
+	spin_unlock_irqrestore(&xhci->lock, flags);
 }
 
 #ifdef CONFIG_PM
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-dbgcap.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-dbgcap.h
@@ -81,7 +81,6 @@
 	DS_ENABLED,
 	DS_CONNECTED,
 	DS_CONFIGURED,
-	DS_STALLED,
 };
 
 struct dbc_ep {
@@ -89,6 +88,7 @@
 	struct list_head		list_pending;
 	struct xhci_ring		*ring;
 	unsigned int			direction:1;
+	unsigned int			halted:1;
 };
 
 #define DBC_QUEUE_SIZE			16
@@ -194,10 +194,13 @@
 }
 
 #ifdef CONFIG_USB_XHCI_DBGCAP
-int xhci_dbc_init(struct xhci_hcd *xhci);
-void xhci_dbc_exit(struct xhci_hcd *xhci);
-int xhci_dbc_tty_probe(struct xhci_hcd *xhci);
+int xhci_create_dbc_dev(struct xhci_hcd *xhci);
+void xhci_remove_dbc_dev(struct xhci_hcd *xhci);
+int xhci_dbc_tty_probe(struct device *dev, void __iomem *res, struct xhci_hcd *xhci);
 void xhci_dbc_tty_remove(struct xhci_dbc *dbc);
+struct xhci_dbc *xhci_alloc_dbc(struct device *dev, void __iomem *res,
+				 const struct dbc_driver *driver);
+void xhci_dbc_remove(struct xhci_dbc *dbc);
 struct dbc_request *dbc_alloc_request(struct xhci_dbc *dbc,
 				      unsigned int direction,
 				      gfp_t flags);
@@ -208,12 +211,12 @@
 int xhci_dbc_resume(struct xhci_hcd *xhci);
 #endif /* CONFIG_PM */
 #else
-static inline int xhci_dbc_init(struct xhci_hcd *xhci)
+static inline int xhci_create_dbc_dev(struct xhci_hcd *xhci)
 {
 	return 0;
 }
 
-static inline void xhci_dbc_exit(struct xhci_hcd *xhci)
+static inline void xhci_remove_dbc_dev(struct xhci_hcd *xhci)
 {
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-dbgtty.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-dbgtty.c
@@ -468,9 +468,9 @@
 	.disconnect		= xhci_dbc_tty_unregister_device,
 };
 
-int xhci_dbc_tty_probe(struct xhci_hcd *xhci)
+int xhci_dbc_tty_probe(struct device *dev, void __iomem *base, struct xhci_hcd *xhci)
 {
-	struct xhci_dbc		*dbc = xhci->dbc;
+	struct xhci_dbc		*dbc;
 	struct dbc_port		*port;
 	int			status;
 
@@ -485,13 +485,22 @@
 		goto out;
 	}
 
-	dbc->driver = &dbc_driver;
-	dbc->priv = port;
+	dbc_tty_driver->driver_state = port;
+
+	dbc = xhci_alloc_dbc(dev, base, &dbc_driver);
+	if (!dbc) {
+		status = -ENOMEM;
+		goto out2;
+	}
 
+	dbc->priv = port;
 
-	dbc_tty_driver->driver_state = port;
+	/* get rid of xhci once this is a real driver binding to a device */
+	xhci->dbc = dbc;
 
 	return 0;
+out2:
+	kfree(port);
 out:
 	/* dbc_tty_exit will be called by module_exit() in the future */
 	dbc_tty_exit();
@@ -506,8 +515,7 @@
 {
 	struct dbc_port         *port = dbc_to_port(dbc);
 
-	dbc->driver = NULL;
-	dbc->priv = NULL;
+	xhci_dbc_remove(dbc);
 	kfree(port);
 
 	/* dbc_tty_exit will be called by  module_exit() in the future */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-debugfs.c
@@ -133,6 +133,7 @@
 	regset->regs = regs;
 	regset->nregs = nregs;
 	regset->base = hcd->regs + base;
+	regset->dev = hcd->self.controller;
 
 	debugfs_create_regset32((const char *)rgs->name, 0444, parent, regset);
 }
@@ -692,7 +693,7 @@
 				     "command-ring",
 				     xhci->debugfs_root);
 
-	xhci_debugfs_create_ring_dir(xhci, &xhci->event_ring,
+	xhci_debugfs_create_ring_dir(xhci, &xhci->interrupter->event_ring,
 				     "event-ring",
 				     xhci->debugfs_root);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-hub.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-hub.c
@@ -257,7 +257,6 @@
 {
 	u16 temp;
 
-	desc->bPwrOn2PwrGood = 10;	/* xhci section 5.4.9 says 20ms max */
 	desc->bHubContrCurrent = 0;
 
 	desc->bNbrPorts = ports;
@@ -292,6 +291,7 @@
 	desc->bDescriptorType = USB_DT_HUB;
 	temp = 1 + (ports / 8);
 	desc->bDescLength = USB_DT_HUB_NONVAR_SIZE + 2 * temp;
+	desc->bPwrOn2PwrGood = 10;	/* xhci section 5.4.8 says 20ms */
 
 	/* The Device Removable bits are reported on a byte granularity.
 	 * If the port doesn't exist within that byte, the bit is set to 0.
@@ -344,6 +344,7 @@
 	xhci_common_hub_descriptor(xhci, desc, ports);
 	desc->bDescriptorType = USB_DT_SS_HUB;
 	desc->bDescLength = USB_DT_SS_HUB_SIZE;
+	desc->bPwrOn2PwrGood = 50;	/* usb 3.1 may fail if less than 100ms */
 
 	/* header decode latency should be zero for roothubs,
 	 * see section 4.23.5.2.
@@ -716,6 +717,7 @@
 			continue;
 
 		retval = xhci_disable_slot(xhci, i);
+		xhci_free_virt_device(xhci, i);
 		if (retval)
 			xhci_err(xhci, "Failed to disable slot %d, %d. Enter test mode anyway\n",
 				 i, retval);
@@ -760,7 +762,7 @@
 	}
 	pm_runtime_allow(xhci_to_hcd(xhci)->self.controller);
 	xhci->test_mode = 0;
-	return xhci_reset(xhci);
+	return xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
 }
 
 void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port,
@@ -903,7 +905,7 @@
 }
 
 static int xhci_handle_usb2_port_link_resume(struct xhci_port *port,
-					     u32 *status, u32 portsc,
+					     u32 portsc,
 					     unsigned long *flags)
 {
 	struct xhci_bus_state *bus_state;
@@ -918,11 +920,10 @@
 	wIndex = port->hcd_portnum;
 
 	if ((portsc & PORT_RESET) || !(portsc & PORT_PE)) {
-		*status = 0xffffffff;
 		return -EINVAL;
 	}
 	/* did port event handler already start resume timing? */
-	if (!bus_state->resume_done[wIndex]) {
+	if (!port->resume_timestamp) {
 		/* If not, maybe we are in a host initated resume? */
 		if (test_bit(wIndex, &bus_state->resuming_ports)) {
 			/* Host initated resume doesn't time the resume
@@ -939,28 +940,29 @@
 				msecs_to_jiffies(USB_RESUME_TIMEOUT);
 
 			set_bit(wIndex, &bus_state->resuming_ports);
-			bus_state->resume_done[wIndex] = timeout;
+			port->resume_timestamp = timeout;
 			mod_timer(&hcd->rh_timer, timeout);
 			usb_hcd_start_port_resume(&hcd->self, wIndex);
 		}
 	/* Has resume been signalled for USB_RESUME_TIME yet? */
-	} else if (time_after_eq(jiffies, bus_state->resume_done[wIndex])) {
+	} else if (time_after_eq(jiffies, port->resume_timestamp)) {
 		int time_left;
 
 		xhci_dbg(xhci, "resume USB2 port %d-%d\n",
 			 hcd->self.busnum, wIndex + 1);
 
-		bus_state->resume_done[wIndex] = 0;
+		port->resume_timestamp = 0;
 		clear_bit(wIndex, &bus_state->resuming_ports);
 
-		set_bit(wIndex, &bus_state->rexit_ports);
+		reinit_completion(&port->rexit_done);
+		port->rexit_active = true;
 
 		xhci_test_and_clear_bit(xhci, port, PORT_PLC);
 		xhci_set_link_state(xhci, port, XDEV_U0);
 
 		spin_unlock_irqrestore(&xhci->lock, *flags);
 		time_left = wait_for_completion_timeout(
-			&bus_state->rexit_done[wIndex],
+			&port->rexit_done,
 			msecs_to_jiffies(XHCI_MAX_REXIT_TIMEOUT_MS));
 		spin_lock_irqsave(&xhci->lock, *flags);
 
@@ -969,7 +971,6 @@
 							    wIndex + 1);
 			if (!slot_id) {
 				xhci_dbg(xhci, "slot_id is zero\n");
-				*status = 0xffffffff;
 				return -ENODEV;
 			}
 			xhci_ring_device(xhci, slot_id);
@@ -978,22 +979,19 @@
 
 			xhci_warn(xhci, "Port resume timed out, port %d-%d: 0x%x\n",
 				  hcd->self.busnum, wIndex + 1, port_status);
-			*status |= USB_PORT_STAT_SUSPEND;
-			clear_bit(wIndex, &bus_state->rexit_ports);
+			/*
+			 * keep rexit_active set if U0 transition failed so we
+			 * know to report PORT_STAT_SUSPEND status back to
+			 * usbcore. It will be cleared later once the port is
+			 * out of RESUME/U3 state
+			 */
 		}
 
 		usb_hcd_end_port_resume(&hcd->self, wIndex);
 		bus_state->port_c_suspend |= 1 << wIndex;
 		bus_state->suspended_ports &= ~(1 << wIndex);
-	} else {
-		/*
-		 * The resume has been signaling for less than
-		 * USB_RESUME_TIME. Report the port status as SUSPEND,
-		 * let the usbcore check port status again and clear
-		 * resume signaling later.
-		 */
-		*status |= USB_PORT_STAT_SUSPEND;
 	}
+
 	return 0;
 }
 
@@ -1045,19 +1043,19 @@
 		*status |= USB_PORT_STAT_C_CONFIG_ERROR << 16;
 
 	/* USB3 specific wPortStatus bits */
-	if (portsc & PORT_POWER) {
+	if (portsc & PORT_POWER)
 		*status |= USB_SS_PORT_STAT_POWER;
-		/* link state handling */
-		if (link_state == XDEV_U0)
-			bus_state->suspended_ports &= ~(1 << portnum);
-	}
 
-	/* remote wake resume signaling complete */
-	if (bus_state->port_remote_wakeup & (1 << portnum) &&
+	/* no longer suspended or resuming */
+	if (link_state != XDEV_U3 &&
 	    link_state != XDEV_RESUME &&
 	    link_state != XDEV_RECOVERY) {
-		bus_state->port_remote_wakeup &= ~(1 << portnum);
-		usb_hcd_end_port_resume(&hcd->self, portnum);
+		/* remote wake resume signaling complete */
+		if (bus_state->port_remote_wakeup & (1 << portnum)) {
+			bus_state->port_remote_wakeup &= ~(1 << portnum);
+			usb_hcd_end_port_resume(&hcd->self, portnum);
+		}
+		bus_state->suspended_ports &= ~(1 << portnum);
 	}
 
 	xhci_hub_report_usb3_link_state(xhci, status, portsc);
@@ -1070,7 +1068,7 @@
 	struct xhci_bus_state *bus_state;
 	u32 link_state;
 	u32 portnum;
-	int ret;
+	int err;
 
 	bus_state = &port->rhub->bus_state;
 	link_state = portsc & PORT_PLS_MASK;
@@ -1086,20 +1084,36 @@
 		if (link_state == XDEV_U2)
 			*status |= USB_PORT_STAT_L1;
 		if (link_state == XDEV_U0) {
-			bus_state->resume_done[portnum] = 0;
-			clear_bit(portnum, &bus_state->resuming_ports);
 			if (bus_state->suspended_ports & (1 << portnum)) {
 				bus_state->suspended_ports &= ~(1 << portnum);
 				bus_state->port_c_suspend |= 1 << portnum;
 			}
 		}
 		if (link_state == XDEV_RESUME) {
-			ret = xhci_handle_usb2_port_link_resume(port, status,
-								portsc, flags);
-			if (ret)
-				return;
+			err = xhci_handle_usb2_port_link_resume(port, portsc,
+								flags);
+			if (err < 0)
+				*status = 0xffffffff;
+			else if (port->resume_timestamp || port->rexit_active)
+				*status |= USB_PORT_STAT_SUSPEND;
 		}
 	}
+
+	/*
+	 * Clear usb2 resume signalling variables if port is no longer suspended
+	 * or resuming. Port either resumed to U0/U1/U2, disconnected, or in a
+	 * error state. Resume related variables should be cleared in all those cases.
+	 */
+	if (link_state != XDEV_U3 && link_state != XDEV_RESUME) {
+		if (port->resume_timestamp ||
+		    test_bit(portnum, &bus_state->resuming_ports)) {
+			port->resume_timestamp = 0;
+			clear_bit(portnum, &bus_state->resuming_ports);
+			usb_hcd_end_port_resume(&port->rhub->hcd->self, portnum);
+		}
+		port->rexit_active = 0;
+		bus_state->suspended_ports &= ~(1 << portnum);
+	}
 }
 
 /*
@@ -1154,18 +1168,6 @@
 	else
 		xhci_get_usb2_port_status(port, &status, raw_port_status,
 					  flags);
-	/*
-	 * Clear stale usb2 resume signalling variables in case port changed
-	 * state during resume signalling. For example on error
-	 */
-	if ((bus_state->resume_done[wIndex] ||
-	     test_bit(wIndex, &bus_state->resuming_ports)) &&
-	    (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
-	    (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME) {
-		bus_state->resume_done[wIndex] = 0;
-		clear_bit(wIndex, &bus_state->resuming_ports);
-		usb_hcd_end_port_resume(&hcd->self, wIndex);
-	}
 
 	if (bus_state->port_c_suspend & (1 << wIndex))
 		status |= USB_PORT_STAT_C_SUSPEND << 16;
@@ -1189,11 +1191,14 @@
 	u16 test_mode = 0;
 	struct xhci_hub *rhub;
 	struct xhci_port **ports;
+	struct xhci_port *port;
+	int portnum1;
 
 	rhub = xhci_get_rhub(hcd);
 	ports = rhub->ports;
 	max_ports = rhub->num_ports;
 	bus_state = &rhub->bus_state;
+	portnum1 = wIndex & 0xff;
 
 	spin_lock_irqsave(&xhci->lock, flags);
 	switch (typeReq) {
@@ -1227,10 +1232,12 @@
 		spin_unlock_irqrestore(&xhci->lock, flags);
 		return retval;
 	case GetPortStatus:
-		if (!wIndex || wIndex > max_ports)
+		if (!portnum1 || portnum1 > max_ports)
 			goto error;
+
 		wIndex--;
-		temp = readl(ports[wIndex]->addr);
+		port = ports[portnum1 - 1];
+		temp = readl(port->addr);
 		if (temp == ~(u32)0) {
 			xhci_hc_died(xhci);
 			retval = -ENODEV;
@@ -1243,7 +1250,7 @@
 			goto error;
 
 		xhci_dbg(xhci, "Get port status %d-%d read: 0x%x, return 0x%x",
-			 hcd->self.busnum, wIndex + 1, temp, status);
+			 hcd->self.busnum, portnum1, temp, status);
 
 		put_unaligned(cpu_to_le32(status), (__le32 *) buf);
 		/* if USB 3.1 extended port status return additional 4 bytes */
@@ -1255,7 +1262,7 @@
 				retval = -EINVAL;
 				break;
 			}
-			port_li = readl(ports[wIndex]->addr + PORTLI);
+			port_li = readl(port->addr + PORTLI);
 			status = xhci_get_ext_port_status(temp, port_li);
 			put_unaligned_le32(status, &buf[4]);
 		}
@@ -1269,11 +1276,14 @@
 			test_mode = (wIndex & 0xff00) >> 8;
 		/* The MSB of wIndex is the U1/U2 timeout */
 		timeout = (wIndex & 0xff00) >> 8;
+
 		wIndex &= 0xff;
-		if (!wIndex || wIndex > max_ports)
+		if (!portnum1 || portnum1 > max_ports)
 			goto error;
+
+		port = ports[portnum1 - 1];
 		wIndex--;
-		temp = readl(ports[wIndex]->addr);
+		temp = readl(port->addr);
 		if (temp == ~(u32)0) {
 			xhci_hc_died(xhci);
 			retval = -ENODEV;
@@ -1283,11 +1293,10 @@
 		/* FIXME: What new port features do we need to support? */
 		switch (wValue) {
 		case USB_PORT_FEAT_SUSPEND:
-			temp = readl(ports[wIndex]->addr);
+			temp = readl(port->addr);
 			if ((temp & PORT_PLS_MASK) != XDEV_U0) {
 				/* Resume the port to U0 first */
-				xhci_set_link_state(xhci, ports[wIndex],
-							XDEV_U0);
+				xhci_set_link_state(xhci, port, XDEV_U0);
 				spin_unlock_irqrestore(&xhci->lock, flags);
 				msleep(10);
 				spin_lock_irqsave(&xhci->lock, flags);
@@ -1296,16 +1305,16 @@
 			 * a port unless the port reports that it is in the
 			 * enabled (PED = ‘1’,PLS < ‘3’) state.
 			 */
-			temp = readl(ports[wIndex]->addr);
+			temp = readl(port->addr);
 			if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
 				|| (temp & PORT_PLS_MASK) >= XDEV_U3) {
 				xhci_warn(xhci, "USB core suspending port %d-%d not in U0/U1/U2\n",
-					  hcd->self.busnum, wIndex + 1);
+					  hcd->self.busnum, portnum1);
 				goto error;
 			}
 
 			slot_id = xhci_find_slot_id_by_port(hcd, xhci,
-					wIndex + 1);
+							    portnum1);
 			if (!slot_id) {
 				xhci_warn(xhci, "slot_id is zero\n");
 				goto error;
@@ -1315,21 +1324,21 @@
 			xhci_stop_device(xhci, slot_id, 1);
 			spin_lock_irqsave(&xhci->lock, flags);
 
-			xhci_set_link_state(xhci, ports[wIndex], XDEV_U3);
+			xhci_set_link_state(xhci, port, XDEV_U3);
 
 			spin_unlock_irqrestore(&xhci->lock, flags);
 			msleep(10); /* wait device to enter */
 			spin_lock_irqsave(&xhci->lock, flags);
 
-			temp = readl(ports[wIndex]->addr);
+			temp = readl(port->addr);
 			bus_state->suspended_ports |= 1 << wIndex;
 			break;
 		case USB_PORT_FEAT_LINK_STATE:
-			temp = readl(ports[wIndex]->addr);
+			temp = readl(port->addr);
 			/* Disable port */
 			if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
 				xhci_dbg(xhci, "Disable port %d-%d\n",
-					 hcd->self.busnum, wIndex + 1);
+					 hcd->self.busnum, portnum1);
 				temp = xhci_port_state_to_neutral(temp);
 				/*
 				 * Clear all change bits, so that we get a new
@@ -1338,18 +1347,17 @@
 				temp |= PORT_CSC | PORT_PEC | PORT_WRC |
 					PORT_OCC | PORT_RC | PORT_PLC |
 					PORT_CEC;
-				writel(temp | PORT_PE, ports[wIndex]->addr);
-				temp = readl(ports[wIndex]->addr);
+				writel(temp | PORT_PE, port->addr);
+				temp = readl(port->addr);
 				break;
 			}
 
 			/* Put link in RxDetect (enable port) */
 			if (link_state == USB_SS_PORT_LS_RX_DETECT) {
 				xhci_dbg(xhci, "Enable port %d-%d\n",
-					 hcd->self.busnum, wIndex + 1);
-				xhci_set_link_state(xhci, ports[wIndex],
-							link_state);
-				temp = readl(ports[wIndex]->addr);
+					 hcd->self.busnum, portnum1);
+				xhci_set_link_state(xhci, port,	link_state);
+				temp = readl(port->addr);
 				break;
 			}
 
@@ -1379,11 +1387,10 @@
 				}
 
 				xhci_dbg(xhci, "Enable compliance mode transition for port %d-%d\n",
-					 hcd->self.busnum, wIndex + 1);
-				xhci_set_link_state(xhci, ports[wIndex],
-						link_state);
+					 hcd->self.busnum, portnum1);
+				xhci_set_link_state(xhci, port, link_state);
 
-				temp = readl(ports[wIndex]->addr);
+				temp = readl(port->addr);
 				break;
 			}
 			/* Port must be enabled */
@@ -1394,8 +1401,7 @@
 			/* Can't set port link state above '3' (U3) */
 			if (link_state > USB_SS_PORT_LS_U3) {
 				xhci_warn(xhci, "Cannot set port %d-%d link state %d\n",
-					  hcd->self.busnum, wIndex + 1,
-					  link_state);
+					  hcd->self.busnum, portnum1, link_state);
 				goto error;
 			}
 
@@ -1417,30 +1423,29 @@
 				    pls == XDEV_RESUME ||
 				    pls == XDEV_RECOVERY) {
 					wait_u0 = true;
-					reinit_completion(&bus_state->u3exit_done[wIndex]);
+					reinit_completion(&port->u3exit_done);
 				}
 				if (pls <= XDEV_U3) /* U1, U2, U3 */
-					xhci_set_link_state(xhci, ports[wIndex],
-							    USB_SS_PORT_LS_U0);
+					xhci_set_link_state(xhci, port, USB_SS_PORT_LS_U0);
 				if (!wait_u0) {
 					if (pls > XDEV_U3)
 						goto error;
 					break;
 				}
 				spin_unlock_irqrestore(&xhci->lock, flags);
-				if (!wait_for_completion_timeout(&bus_state->u3exit_done[wIndex],
-								 msecs_to_jiffies(100)))
+				if (!wait_for_completion_timeout(&port->u3exit_done,
+								 msecs_to_jiffies(500)))
 					xhci_dbg(xhci, "missing U0 port change event for port %d-%d\n",
-						 hcd->self.busnum, wIndex + 1);
+						 hcd->self.busnum, portnum1);
 				spin_lock_irqsave(&xhci->lock, flags);
-				temp = readl(ports[wIndex]->addr);
+				temp = readl(port->addr);
 				break;
 			}
 
 			if (link_state == USB_SS_PORT_LS_U3) {
 				int retries = 16;
 				slot_id = xhci_find_slot_id_by_port(hcd, xhci,
-						wIndex + 1);
+								    portnum1);
 				if (slot_id) {
 					/* unlock to execute stop endpoint
 					 * commands */
@@ -1449,16 +1454,16 @@
 					xhci_stop_device(xhci, slot_id, 1);
 					spin_lock_irqsave(&xhci->lock, flags);
 				}
-				xhci_set_link_state(xhci, ports[wIndex], USB_SS_PORT_LS_U3);
+				xhci_set_link_state(xhci, port, USB_SS_PORT_LS_U3);
 				spin_unlock_irqrestore(&xhci->lock, flags);
 				while (retries--) {
 					usleep_range(4000, 8000);
-					temp = readl(ports[wIndex]->addr);
+					temp = readl(port->addr);
 					if ((temp & PORT_PLS_MASK) == XDEV_U3)
 						break;
 				}
 				spin_lock_irqsave(&xhci->lock, flags);
-				temp = readl(ports[wIndex]->addr);
+				temp = readl(port->addr);
 				bus_state->suspended_ports |= 1 << wIndex;
 			}
 			break;
@@ -1473,39 +1478,38 @@
 			break;
 		case USB_PORT_FEAT_RESET:
 			temp = (temp | PORT_RESET);
-			writel(temp, ports[wIndex]->addr);
+			writel(temp, port->addr);
 
-			temp = readl(ports[wIndex]->addr);
+			temp = readl(port->addr);
 			xhci_dbg(xhci, "set port reset, actual port %d-%d status  = 0x%x\n",
-				 hcd->self.busnum, wIndex + 1, temp);
+				 hcd->self.busnum, portnum1, temp);
 			break;
 		case USB_PORT_FEAT_REMOTE_WAKE_MASK:
-			xhci_set_remote_wake_mask(xhci, ports[wIndex],
-						  wake_mask);
-			temp = readl(ports[wIndex]->addr);
+			xhci_set_remote_wake_mask(xhci, port, wake_mask);
+			temp = readl(port->addr);
 			xhci_dbg(xhci, "set port remote wake mask, actual port %d-%d status  = 0x%x\n",
-				 hcd->self.busnum, wIndex + 1, temp);
+				 hcd->self.busnum, portnum1, temp);
 			break;
 		case USB_PORT_FEAT_BH_PORT_RESET:
 			temp |= PORT_WR;
-			writel(temp, ports[wIndex]->addr);
-			temp = readl(ports[wIndex]->addr);
+			writel(temp, port->addr);
+			temp = readl(port->addr);
 			break;
 		case USB_PORT_FEAT_U1_TIMEOUT:
 			if (hcd->speed < HCD_USB3)
 				goto error;
-			temp = readl(ports[wIndex]->addr + PORTPMSC);
+			temp = readl(port->addr + PORTPMSC);
 			temp &= ~PORT_U1_TIMEOUT_MASK;
 			temp |= PORT_U1_TIMEOUT(timeout);
-			writel(temp, ports[wIndex]->addr + PORTPMSC);
+			writel(temp, port->addr + PORTPMSC);
 			break;
 		case USB_PORT_FEAT_U2_TIMEOUT:
 			if (hcd->speed < HCD_USB3)
 				goto error;
-			temp = readl(ports[wIndex]->addr + PORTPMSC);
+			temp = readl(port->addr + PORTPMSC);
 			temp &= ~PORT_U2_TIMEOUT_MASK;
 			temp |= PORT_U2_TIMEOUT(timeout);
-			writel(temp, ports[wIndex]->addr + PORTPMSC);
+			writel(temp, port->addr + PORTPMSC);
 			break;
 		case USB_PORT_FEAT_TEST:
 			/* 4.19.6 Port Test Modes (USB2 Test Mode) */
@@ -1521,13 +1525,16 @@
 			goto error;
 		}
 		/* unblock any posted writes */
-		temp = readl(ports[wIndex]->addr);
+		temp = readl(port->addr);
 		break;
 	case ClearPortFeature:
-		if (!wIndex || wIndex > max_ports)
+		if (!portnum1 || portnum1 > max_ports)
 			goto error;
+
+		port = ports[portnum1 - 1];
+
 		wIndex--;
-		temp = readl(ports[wIndex]->addr);
+		temp = readl(port->addr);
 		if (temp == ~(u32)0) {
 			xhci_hc_died(xhci);
 			retval = -ENODEV;
@@ -1537,7 +1544,7 @@
 		temp = xhci_port_state_to_neutral(temp);
 		switch (wValue) {
 		case USB_PORT_FEAT_SUSPEND:
-			temp = readl(ports[wIndex]->addr);
+			temp = readl(port->addr);
 			xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
 			xhci_dbg(xhci, "PORTSC %04x\n", temp);
 			if (temp & PORT_RESET)
@@ -1548,20 +1555,18 @@
 
 				set_bit(wIndex, &bus_state->resuming_ports);
 				usb_hcd_start_port_resume(&hcd->self, wIndex);
-				xhci_set_link_state(xhci, ports[wIndex],
-						    XDEV_RESUME);
+				xhci_set_link_state(xhci, port, XDEV_RESUME);
 				spin_unlock_irqrestore(&xhci->lock, flags);
 				msleep(USB_RESUME_TIMEOUT);
 				spin_lock_irqsave(&xhci->lock, flags);
-				xhci_set_link_state(xhci, ports[wIndex],
-							XDEV_U0);
+				xhci_set_link_state(xhci, port, XDEV_U0);
 				clear_bit(wIndex, &bus_state->resuming_ports);
 				usb_hcd_end_port_resume(&hcd->self, wIndex);
 			}
 			bus_state->port_c_suspend |= 1 << wIndex;
 
 			slot_id = xhci_find_slot_id_by_port(hcd, xhci,
-					wIndex + 1);
+					portnum1);
 			if (!slot_id) {
 				xhci_dbg(xhci, "slot_id is zero\n");
 				goto error;
@@ -1579,11 +1584,11 @@
 		case USB_PORT_FEAT_C_PORT_LINK_STATE:
 		case USB_PORT_FEAT_C_PORT_CONFIG_ERROR:
 			xhci_clear_port_change_bit(xhci, wValue, wIndex,
-					ports[wIndex]->addr, temp);
+					port->addr, temp);
 			break;
 		case USB_PORT_FEAT_ENABLE:
 			xhci_disable_port(hcd, xhci, wIndex,
-					ports[wIndex]->addr, temp);
+					port->addr, temp);
 			break;
 		case USB_PORT_FEAT_POWER:
 			xhci_set_port_power(xhci, hcd, wIndex, false, &flags);
@@ -1642,6 +1647,17 @@
 
 	status = bus_state->resuming_ports;
 
+	/*
+	 * SS devices are only visible to roothub after link training completes.
+	 * Keep polling roothubs for a grace period after xHC start
+	 */
+	if (xhci->run_graceperiod) {
+		if (time_before(jiffies, xhci->run_graceperiod))
+			status = 1;
+		else
+			xhci->run_graceperiod = 0;
+	}
+
 	mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC | PORT_CEC;
 
 	/* For each port, did anything change?  If so, set that bit in buf. */
@@ -1656,8 +1672,8 @@
 
 		if ((temp & mask) != 0 ||
 			(bus_state->port_c_suspend & 1 << i) ||
-			(bus_state->resume_done[i] && time_after_eq(
-			    jiffies, bus_state->resume_done[i]))) {
+			(ports[i]->resume_timestamp && time_after_eq(
+			    jiffies, ports[i]->resume_timestamp))) {
 			buf[(i + 1) / 8] |= 1 << (i + 1) % 8;
 			status = 1;
 		}
@@ -1925,6 +1941,13 @@
 		}
 	}
 
+	/* After resuming back from suspend, the controller may not initiate
+	 * LFPS.U3_exit signalling if not given a delay after updating the
+	 * link from U3->U0. So, lets wait for atleast 1ms
+	 */
+	if (next_state == XDEV_U0)
+		mdelay(1);
+
 	/* poll for U0 link state complete, both USB2 and USB3 */
 	for_each_set_bit(port_index, &bus_state->bus_suspended, BITS_PER_LONG) {
 		sret = xhci_handshake(ports[port_index]->addr, PORT_PLC,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-mem.c
@@ -642,7 +642,7 @@
 			num_stream_ctxs, &stream_info->ctx_array_dma,
 			mem_flags);
 	if (!stream_info->stream_ctx_array)
-		goto cleanup_ctx;
+		goto cleanup_ring_array;
 	memset(stream_info->stream_ctx_array, 0,
 			sizeof(struct xhci_stream_ctx)*num_stream_ctxs);
 
@@ -677,6 +677,16 @@
 		xhci_dbg(xhci, "Setting stream %d ring ptr to 0x%08llx\n",
 				cur_stream, (unsigned long long) addr);
 
+		if (xhci->quirks & XHCI_STREAM_QUIRK) {
+			/* dwc3 host controller has an issue where it doesn't
+			 * process BULK IN stream rings even after ringing
+			 * DoorBell, so setup a timer to aviod hang condition.
+			 */
+			timer_setup(&cur_ring->stream_timer,
+				    xhci_stream_timeout, 0);
+			cur_ring->xhci = xhci;
+		}
+
 		ret = xhci_update_stream_mapping(cur_ring, mem_flags);
 		if (ret) {
 			xhci_ring_free(xhci, cur_ring);
@@ -703,6 +713,11 @@
 	}
 	xhci_free_command(xhci, stream_info->free_streams_command);
 cleanup_ctx:
+	xhci_free_stream_ctx(xhci,
+		stream_info->num_stream_ctxs,
+		stream_info->stream_ctx_array,
+		stream_info->ctx_array_dma);
+cleanup_ring_array:
 	kfree(stream_info->stream_rings);
 cleanup_info:
 	kfree(stream_info);
@@ -763,6 +778,10 @@
 	for (cur_stream = 1; cur_stream < stream_info->num_streams;
 			cur_stream++) {
 		cur_ring = stream_info->stream_rings[cur_stream];
+
+		if (xhci->quirks & XHCI_STREAM_QUIRK)
+			del_timer_sync(&cur_ring->stream_timer);
+
 		if (cur_ring) {
 			xhci_ring_free(xhci, cur_ring);
 			stream_info->stream_rings[cur_stream] = NULL;
@@ -893,15 +912,19 @@
 		if (dev->eps[i].stream_info)
 			xhci_free_stream_info(xhci,
 					dev->eps[i].stream_info);
-		/* Endpoints on the TT/root port lists should have been removed
-		 * when usb_disable_device() was called for the device.
-		 * We can't drop them anyway, because the udev might have gone
-		 * away by this point, and we can't tell what speed it was.
+		/*
+		 * Endpoints are normally deleted from the bandwidth list when
+		 * endpoints are dropped, before device is freed.
+		 * If host is dying or being removed then endpoints aren't
+		 * dropped cleanly, so delete the endpoint from list here.
+		 * Only applicable for hosts with software bandwidth checking.
 		 */
-		if (!list_empty(&dev->eps[i].bw_endpoint_list))
-			xhci_warn(xhci, "Slot %u endpoint %u "
-					"not removed from BW list!\n",
-					slot_id, i);
+
+		if (!list_empty(&dev->eps[i].bw_endpoint_list)) {
+			list_del_init(&dev->eps[i].bw_endpoint_list);
+			xhci_dbg(xhci, "Slot %u endpoint %u not removed from BW list!\n",
+				 slot_id, i);
+		}
 	}
 	/* If this is a hub, free the TT(s) from the TT list */
 	xhci_free_tt_info(xhci, dev, slot_id);
@@ -1752,6 +1775,8 @@
 	}
 
 	command->status = 0;
+	/* set default timeout to 5000 ms */
+	command->timeout_ms = XHCI_CMD_DEFAULT_TIMEOUT;
 	INIT_LIST_HEAD(&command->cmd_list);
 	return command;
 }
@@ -1819,17 +1844,43 @@
 	return 0;
 }
 
-void xhci_free_erst(struct xhci_hcd *xhci, struct xhci_erst *erst)
+static void
+xhci_free_interrupter(struct xhci_hcd *xhci, struct xhci_interrupter *ir)
 {
-	size_t size;
 	struct device *dev = xhci_to_hcd(xhci)->self.sysdev;
+	size_t erst_size;
+	u64 tmp64;
+	u32 tmp;
+
+	if (!ir)
+		return;
 
-	size = sizeof(struct xhci_erst_entry) * (erst->num_entries);
-	if (erst->entries)
-		dma_free_coherent(dev, size,
-				erst->entries,
-				erst->erst_dma_addr);
-	erst->entries = NULL;
+	erst_size = sizeof(struct xhci_erst_entry) * (ir->erst.num_entries);
+	if (ir->erst.entries)
+		dma_free_coherent(dev, erst_size,
+				  ir->erst.entries,
+				  ir->erst.erst_dma_addr);
+	ir->erst.entries = NULL;
+
+	/*
+	 * Clean out interrupter registers except ERSTBA. Clearing either the
+	 * low or high 32 bits of ERSTBA immediately causes the controller to
+	 * dereference the partially cleared 64 bit address, causing IOMMU error.
+	 */
+	tmp = readl(&ir->ir_set->erst_size);
+	tmp &= ERST_SIZE_MASK;
+	writel(tmp, &ir->ir_set->erst_size);
+
+	tmp64 = xhci_read_64(xhci, &ir->ir_set->erst_dequeue);
+	tmp64 &= (u64) ERST_PTR_MASK;
+	xhci_write_64(xhci, tmp64, &ir->ir_set->erst_dequeue);
+
+	/* free interrrupter event ring */
+	if (ir->event_ring)
+		xhci_ring_free(xhci, ir->event_ring);
+	ir->event_ring = NULL;
+
+	kfree(ir);
 }
 
 void xhci_mem_cleanup(struct xhci_hcd *xhci)
@@ -1839,12 +1890,9 @@
 
 	cancel_delayed_work_sync(&xhci->cmd_timer);
 
-	xhci_free_erst(xhci, &xhci->erst);
-
-	if (xhci->event_ring)
-		xhci_ring_free(xhci, xhci->event_ring);
-	xhci->event_ring = NULL;
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Freed event ring");
+	xhci_free_interrupter(xhci, xhci->interrupter);
+	xhci->interrupter = NULL;
+	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Freed primary event ring");
 
 	if (xhci->lpm_command)
 		xhci_free_command(xhci, xhci->lpm_command);
@@ -1932,176 +1980,18 @@
 	xhci->usb3_rhub.bus_state.bus_suspended = 0;
 }
 
-static int xhci_test_trb_in_td(struct xhci_hcd *xhci,
-		struct xhci_segment *input_seg,
-		union xhci_trb *start_trb,
-		union xhci_trb *end_trb,
-		dma_addr_t input_dma,
-		struct xhci_segment *result_seg,
-		char *test_name, int test_number)
-{
-	unsigned long long start_dma;
-	unsigned long long end_dma;
-	struct xhci_segment *seg;
-
-	start_dma = xhci_trb_virt_to_dma(input_seg, start_trb);
-	end_dma = xhci_trb_virt_to_dma(input_seg, end_trb);
-
-	seg = trb_in_td(xhci, input_seg, start_trb, end_trb, input_dma, false);
-	if (seg != result_seg) {
-		xhci_warn(xhci, "WARN: %s TRB math test %d failed!\n",
-				test_name, test_number);
-		xhci_warn(xhci, "Tested TRB math w/ seg %p and "
-				"input DMA 0x%llx\n",
-				input_seg,
-				(unsigned long long) input_dma);
-		xhci_warn(xhci, "starting TRB %p (0x%llx DMA), "
-				"ending TRB %p (0x%llx DMA)\n",
-				start_trb, start_dma,
-				end_trb, end_dma);
-		xhci_warn(xhci, "Expected seg %p, got seg %p\n",
-				result_seg, seg);
-		trb_in_td(xhci, input_seg, start_trb, end_trb, input_dma,
-			  true);
-		return -1;
-	}
-	return 0;
-}
-
-/* TRB math checks for xhci_trb_in_td(), using the command and event rings. */
-static int xhci_check_trb_in_td_math(struct xhci_hcd *xhci)
-{
-	struct {
-		dma_addr_t		input_dma;
-		struct xhci_segment	*result_seg;
-	} simple_test_vector [] = {
-		/* A zeroed DMA field should fail */
-		{ 0, NULL },
-		/* One TRB before the ring start should fail */
-		{ xhci->event_ring->first_seg->dma - 16, NULL },
-		/* One byte before the ring start should fail */
-		{ xhci->event_ring->first_seg->dma - 1, NULL },
-		/* Starting TRB should succeed */
-		{ xhci->event_ring->first_seg->dma, xhci->event_ring->first_seg },
-		/* Ending TRB should succeed */
-		{ xhci->event_ring->first_seg->dma + (TRBS_PER_SEGMENT - 1)*16,
-			xhci->event_ring->first_seg },
-		/* One byte after the ring end should fail */
-		{ xhci->event_ring->first_seg->dma + (TRBS_PER_SEGMENT - 1)*16 + 1, NULL },
-		/* One TRB after the ring end should fail */
-		{ xhci->event_ring->first_seg->dma + (TRBS_PER_SEGMENT)*16, NULL },
-		/* An address of all ones should fail */
-		{ (dma_addr_t) (~0), NULL },
-	};
-	struct {
-		struct xhci_segment	*input_seg;
-		union xhci_trb		*start_trb;
-		union xhci_trb		*end_trb;
-		dma_addr_t		input_dma;
-		struct xhci_segment	*result_seg;
-	} complex_test_vector [] = {
-		/* Test feeding a valid DMA address from a different ring */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = xhci->event_ring->first_seg->trbs,
-			.end_trb = &xhci->event_ring->first_seg->trbs[TRBS_PER_SEGMENT - 1],
-			.input_dma = xhci->cmd_ring->first_seg->dma,
-			.result_seg = NULL,
-		},
-		/* Test feeding a valid end TRB from a different ring */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = xhci->event_ring->first_seg->trbs,
-			.end_trb = &xhci->cmd_ring->first_seg->trbs[TRBS_PER_SEGMENT - 1],
-			.input_dma = xhci->cmd_ring->first_seg->dma,
-			.result_seg = NULL,
-		},
-		/* Test feeding a valid start and end TRB from a different ring */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = xhci->cmd_ring->first_seg->trbs,
-			.end_trb = &xhci->cmd_ring->first_seg->trbs[TRBS_PER_SEGMENT - 1],
-			.input_dma = xhci->cmd_ring->first_seg->dma,
-			.result_seg = NULL,
-		},
-		/* TRB in this ring, but after this TD */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = &xhci->event_ring->first_seg->trbs[0],
-			.end_trb = &xhci->event_ring->first_seg->trbs[3],
-			.input_dma = xhci->event_ring->first_seg->dma + 4*16,
-			.result_seg = NULL,
-		},
-		/* TRB in this ring, but before this TD */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = &xhci->event_ring->first_seg->trbs[3],
-			.end_trb = &xhci->event_ring->first_seg->trbs[6],
-			.input_dma = xhci->event_ring->first_seg->dma + 2*16,
-			.result_seg = NULL,
-		},
-		/* TRB in this ring, but after this wrapped TD */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = &xhci->event_ring->first_seg->trbs[TRBS_PER_SEGMENT - 3],
-			.end_trb = &xhci->event_ring->first_seg->trbs[1],
-			.input_dma = xhci->event_ring->first_seg->dma + 2*16,
-			.result_seg = NULL,
-		},
-		/* TRB in this ring, but before this wrapped TD */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = &xhci->event_ring->first_seg->trbs[TRBS_PER_SEGMENT - 3],
-			.end_trb = &xhci->event_ring->first_seg->trbs[1],
-			.input_dma = xhci->event_ring->first_seg->dma + (TRBS_PER_SEGMENT - 4)*16,
-			.result_seg = NULL,
-		},
-		/* TRB not in this ring, and we have a wrapped TD */
-		{	.input_seg = xhci->event_ring->first_seg,
-			.start_trb = &xhci->event_ring->first_seg->trbs[TRBS_PER_SEGMENT - 3],
-			.end_trb = &xhci->event_ring->first_seg->trbs[1],
-			.input_dma = xhci->cmd_ring->first_seg->dma + 2*16,
-			.result_seg = NULL,
-		},
-	};
-
-	unsigned int num_tests;
-	int i, ret;
-
-	num_tests = ARRAY_SIZE(simple_test_vector);
-	for (i = 0; i < num_tests; i++) {
-		ret = xhci_test_trb_in_td(xhci,
-				xhci->event_ring->first_seg,
-				xhci->event_ring->first_seg->trbs,
-				&xhci->event_ring->first_seg->trbs[TRBS_PER_SEGMENT - 1],
-				simple_test_vector[i].input_dma,
-				simple_test_vector[i].result_seg,
-				"Simple", i);
-		if (ret < 0)
-			return ret;
-	}
-
-	num_tests = ARRAY_SIZE(complex_test_vector);
-	for (i = 0; i < num_tests; i++) {
-		ret = xhci_test_trb_in_td(xhci,
-				complex_test_vector[i].input_seg,
-				complex_test_vector[i].start_trb,
-				complex_test_vector[i].end_trb,
-				complex_test_vector[i].input_dma,
-				complex_test_vector[i].result_seg,
-				"Complex", i);
-		if (ret < 0)
-			return ret;
-	}
-	xhci_dbg(xhci, "TRB math tests passed.\n");
-	return 0;
-}
-
-static void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
+static void xhci_set_hc_event_deq(struct xhci_hcd *xhci, struct xhci_interrupter *ir)
 {
 	u64 temp;
 	dma_addr_t deq;
 
-	deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg,
-			xhci->event_ring->dequeue);
+	deq = xhci_trb_virt_to_dma(ir->event_ring->deq_seg,
+			ir->event_ring->dequeue);
 	if (!deq)
 		xhci_warn(xhci, "WARN something wrong with SW event ring "
 				"dequeue ptr.\n");
 	/* Update HC event ring dequeue pointer */
-	temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	temp = xhci_read_64(xhci, &ir->ir_set->erst_dequeue);
 	temp &= ERST_PTR_MASK;
 	/* Don't clear the EHB bit (which is RW1C) because
 	 * there might be more events to service.
@@ -2111,7 +2001,7 @@
 			"// Write event ring dequeue pointer, "
 			"preserving EHB bit");
 	xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp,
-			&xhci->ir_set->erst_dequeue);
+			&ir->ir_set->erst_dequeue);
 }
 
 static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports,
@@ -2119,7 +2009,7 @@
 {
 	u32 temp, port_offset, port_count;
 	int i;
-	u8 major_revision, minor_revision;
+	u8 major_revision, minor_revision, tmp_minor_revision;
 	struct xhci_hub *rhub;
 	struct device *dev = xhci_to_hcd(xhci)->self.sysdev;
 	struct xhci_port_cap *port_cap;
@@ -2139,6 +2029,15 @@
 		 */
 		if (minor_revision > 0x00 && minor_revision < 0x10)
 			minor_revision <<= 4;
+		/*
+		 * Some zhaoxin's xHCI controller that follow usb3.1 spec
+		 * but only support Gen1.
+		 */
+		if (xhci->quirks & XHCI_ZHAOXIN_HOST) {
+			tmp_minor_revision = minor_revision;
+			minor_revision = 0;
+		}
+
 	} else if (major_revision <= 0x02) {
 		rhub = &xhci->usb2_rhub;
 	} else {
@@ -2148,10 +2047,6 @@
 		/* Ignoring port protocol we can't understand. FIXME */
 		return;
 	}
-	rhub->maj_rev = XHCI_EXT_PORT_MAJOR(temp);
-
-	if (rhub->min_rev < minor_revision)
-		rhub->min_rev = minor_revision;
 
 	/* Port offset and count in the third dword, see section 7.2 */
 	temp = readl(addr + 2);
@@ -2170,8 +2065,6 @@
 	if (xhci->num_port_caps > max_caps)
 		return;
 
-	port_cap->maj_rev = major_revision;
-	port_cap->min_rev = minor_revision;
 	port_cap->psi_count = XHCI_EXT_PORT_PSIC(temp);
 
 	if (port_cap->psi_count) {
@@ -2192,6 +2085,11 @@
 				  XHCI_EXT_PORT_PSIV(port_cap->psi[i - 1])))
 				port_cap->psi_uid_count++;
 
+			if (xhci->quirks & XHCI_ZHAOXIN_HOST &&
+			    major_revision == 0x03 &&
+			    XHCI_EXT_PORT_PSIV(port_cap->psi[i]) >= 5)
+				minor_revision = tmp_minor_revision;
+
 			xhci_dbg(xhci, "PSIV:%d PSIE:%d PLT:%d PFD:%d LP:%d PSIM:%d\n",
 				  XHCI_EXT_PORT_PSIV(port_cap->psi[i]),
 				  XHCI_EXT_PORT_PSIE(port_cap->psi[i]),
@@ -2201,6 +2099,15 @@
 				  XHCI_EXT_PORT_PSIM(port_cap->psi[i]));
 		}
 	}
+
+	rhub->maj_rev = major_revision;
+
+	if (rhub->min_rev < minor_revision)
+		rhub->min_rev = minor_revision;
+
+	port_cap->maj_rev = major_revision;
+	port_cap->min_rev = minor_revision;
+
 	/* cache usb2 port capabilities */
 	if (major_revision < 0x03 && xhci->num_ext_caps < max_caps)
 		xhci->ext_caps[xhci->num_ext_caps++] = temp;
@@ -2292,6 +2199,9 @@
 		xhci->hw_ports[i].addr = &xhci->op_regs->port_status_base +
 			NUM_PORT_REGS * i;
 		xhci->hw_ports[i].hw_portnum = i;
+
+		init_completion(&xhci->hw_ports[i].rexit_done);
+		init_completion(&xhci->hw_ports[i].u3exit_done);
 	}
 
 	xhci->rh_bw = kcalloc_node(num_ports, sizeof(*xhci->rh_bw), flags,
@@ -2377,6 +2287,71 @@
 	return 0;
 }
 
+static struct xhci_interrupter *
+xhci_alloc_interrupter(struct xhci_hcd *xhci, unsigned int intr_num, gfp_t flags)
+{
+	struct device *dev = xhci_to_hcd(xhci)->self.sysdev;
+	struct xhci_interrupter *ir;
+	u64 erst_base;
+	u32 erst_size;
+	int ret;
+
+	if (intr_num > xhci->max_interrupters) {
+		xhci_warn(xhci, "Can't allocate interrupter %d, max interrupters %d\n",
+			  intr_num, xhci->max_interrupters);
+		return NULL;
+	}
+
+	if (xhci->interrupter) {
+		xhci_warn(xhci, "Can't allocate already set up interrupter %d\n", intr_num);
+		return NULL;
+	}
+
+	ir = kzalloc_node(sizeof(*ir), flags, dev_to_node(dev));
+	if (!ir)
+		return NULL;
+
+	ir->ir_set = &xhci->run_regs->ir_set[intr_num];
+	ir->event_ring = xhci_ring_alloc(xhci, ERST_NUM_SEGS, 1, TYPE_EVENT,
+					0, flags);
+	if (!ir->event_ring) {
+		xhci_warn(xhci, "Failed to allocate interrupter %d event ring\n", intr_num);
+		goto fail_ir;
+	}
+
+	ret = xhci_alloc_erst(xhci, ir->event_ring, &ir->erst, flags);
+	if (ret) {
+		xhci_warn(xhci, "Failed to allocate interrupter %d erst\n", intr_num);
+		goto fail_ev;
+
+	}
+	/* set ERST count with the number of entries in the segment table */
+	erst_size = readl(&ir->ir_set->erst_size);
+	erst_size &= ERST_SIZE_MASK;
+	erst_size |= ERST_NUM_SEGS;
+	writel(erst_size, &ir->ir_set->erst_size);
+
+	erst_base = xhci_read_64(xhci, &ir->ir_set->erst_base);
+	erst_base &= ERST_BASE_RSVDP;
+	erst_base |= ir->erst.erst_dma_addr & ~ERST_BASE_RSVDP;
+	if (xhci->quirks & XHCI_WRITE_64_HI_LO)
+		hi_lo_writeq(erst_base, &ir->ir_set->erst_base);
+	else
+		xhci_write_64(xhci, erst_base, &ir->ir_set->erst_base);
+
+	/* Set the event ring dequeue address of this interrupter */
+	xhci_set_hc_event_deq(xhci, ir);
+
+	return ir;
+
+fail_ev:
+	xhci_ring_free(xhci, ir->event_ring);
+fail_ir:
+	kfree(ir);
+
+	return NULL;
+}
+
 int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 {
 	dma_addr_t	dma;
@@ -2384,7 +2359,7 @@
 	unsigned int	val, val2;
 	u64		val_64;
 	u32		page_size, temp;
-	int		i, ret;
+	int		i;
 
 	INIT_LIST_HEAD(&xhci->cmd_list);
 
@@ -2445,8 +2420,13 @@
 	 * and our use of dma addresses in the trb_address_map radix tree needs
 	 * TRB_SEGMENT_SIZE alignment, so we pick the greater alignment need.
 	 */
-	xhci->segment_pool = dma_pool_create("xHCI ring segments", dev,
-			TRB_SEGMENT_SIZE, TRB_SEGMENT_SIZE, xhci->page_size);
+	if (xhci->quirks & XHCI_TRB_OVERFETCH)
+		/* Buggy HC prefetches beyond segment bounds - allocate dummy space at the end */
+		xhci->segment_pool = dma_pool_create("xHCI ring segments", dev,
+				TRB_SEGMENT_SIZE * 2, TRB_SEGMENT_SIZE * 2, xhci->page_size * 2);
+	else
+		xhci->segment_pool = dma_pool_create("xHCI ring segments", dev,
+				TRB_SEGMENT_SIZE, TRB_SEGMENT_SIZE, xhci->page_size);
 
 	/* See Table 46 and Note on Figure 55 */
 	xhci->device_pool = dma_pool_create("xHCI input/output contexts", dev,
@@ -2505,48 +2485,13 @@
 			" from cap regs base addr", val);
 	xhci->dba = (void __iomem *) xhci->cap_regs + val;
 	/* Set ir_set to interrupt register set 0 */
-	xhci->ir_set = &xhci->run_regs->ir_set[0];
-
-	/*
-	 * Event ring setup: Allocate a normal ring, but also setup
-	 * the event ring segment table (ERST).  Section 4.9.3.
-	 */
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Allocating event ring");
-	xhci->event_ring = xhci_ring_alloc(xhci, ERST_NUM_SEGS, 1, TYPE_EVENT,
-					0, flags);
-	if (!xhci->event_ring)
-		goto fail;
-	if (xhci_check_trb_in_td_math(xhci) < 0)
-		goto fail;
-
-	ret = xhci_alloc_erst(xhci, xhci->event_ring, &xhci->erst, flags);
-	if (ret)
-		goto fail;
-
-	/* set ERST count with the number of entries in the segment table */
-	val = readl(&xhci->ir_set->erst_size);
-	val &= ERST_SIZE_MASK;
-	val |= ERST_NUM_SEGS;
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
-			"// Write ERST size = %i to ir_set 0 (some bits preserved)",
-			val);
-	writel(val, &xhci->ir_set->erst_size);
 
+	/* allocate and set up primary interrupter with an event ring. */
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
-			"// Set ERST entries to point to event ring.");
-	/* set the segment table base address */
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
-			"// Set ERST base address for ir_set 0 = 0x%llx",
-			(unsigned long long)xhci->erst.erst_dma_addr);
-	val_64 = xhci_read_64(xhci, &xhci->ir_set->erst_base);
-	val_64 &= ERST_PTR_MASK;
-	val_64 |= (xhci->erst.erst_dma_addr & (u64) ~ERST_PTR_MASK);
-	xhci_write_64(xhci, val_64, &xhci->ir_set->erst_base);
-
-	/* Set the event ring dequeue address */
-	xhci_set_hc_event_deq(xhci);
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
-			"Wrote ERST address to ir_set 0.");
+		       "Allocating primary event ring");
+	xhci->interrupter = xhci_alloc_interrupter(xhci, 0, flags);
+	if (!xhci->interrupter)
+		goto fail;
 
 	xhci->isoc_bei_interval = AVOID_BEI_INTERVAL_MAX;
 
@@ -2557,13 +2502,6 @@
 	 */
 	for (i = 0; i < MAX_HC_SLOTS; i++)
 		xhci->devs[i] = NULL;
-	for (i = 0; i < USB_MAXCHILDREN; i++) {
-		xhci->usb2_rhub.bus_state.resume_done[i] = 0;
-		xhci->usb3_rhub.bus_state.resume_done[i] = 0;
-		/* Only the USB 2.0 completions will ever be used. */
-		init_completion(&xhci->usb2_rhub.bus_state.rexit_done[i]);
-		init_completion(&xhci->usb3_rhub.bus_state.u3exit_done[i]);
-	}
 
 	if (scratchpad_alloc(xhci, flags))
 		goto fail;
@@ -2583,7 +2521,7 @@
 
 fail:
 	xhci_halt(xhci);
-	xhci_reset(xhci);
+	xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
 	xhci_mem_cleanup(xhci);
 	return -ENOMEM;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-mtk-sch.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-mtk-sch.c
@@ -465,7 +465,7 @@
 		 */
 		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
 			k = XHCI_MTK_BW_INDEX(base + j);
-			tmp = tt->fs_bus_bw[k] + sch_ep->bw_budget_table[j];
+			tmp = tt->fs_bus_bw[k] + sch_ep->bw_cost_per_microframe;
 			if (tmp > FS_PAYLOAD_MAX)
 				return -ESCH_BW_OVERFLOW;
 		}
@@ -476,7 +476,6 @@
 
 static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
-	u32 extra_cs_count;
 	u32 start_ss, last_ss;
 	u32 start_cs, last_cs;
 
@@ -512,18 +511,12 @@
 		if (last_cs > 7)
 			return -ESCH_CS_OVERFLOW;
 
-		if (sch_ep->ep_type == ISOC_IN_EP)
-			extra_cs_count = (last_cs == 7) ? 1 : 2;
-		else /*  ep_type : INTR IN / INTR OUT */
-			extra_cs_count = 1;
-
-		cs_count += extra_cs_count;
 		if (cs_count > 7)
 			cs_count = 7; /* HW limit */
 
 		sch_ep->cs_count = cs_count;
-		/* one for ss, the other for idle */
-		sch_ep->num_budget_microframes = cs_count + 2;
+		/* ss, idle are ignored */
+		sch_ep->num_budget_microframes = cs_count;
 
 		/*
 		 * if interval=1, maxp >752, num_budge_micoframe is larger
@@ -539,19 +532,17 @@
 static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
+	int bw_updated;
 	u32 base;
-	int i, j, k;
+	int i, j;
+
+	bw_updated = sch_ep->bw_cost_per_microframe * (used ? 1 : -1);
 
 	for (i = 0; i < sch_ep->num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
 
-		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
-			k = XHCI_MTK_BW_INDEX(base + j);
-			if (used)
-				tt->fs_bus_bw[k] += sch_ep->bw_budget_table[j];
-			else
-				tt->fs_bus_bw[k] -= sch_ep->bw_budget_table[j];
-		}
+		for (j = 0; j < sch_ep->num_budget_microframes; j++)
+			tt->fs_bus_bw[XHCI_MTK_BW_INDEX(base + j)] += bw_updated;
 	}
 
 	if (used)
@@ -781,7 +772,7 @@
 
 	ret = xhci_check_bandwidth(hcd, udev);
 	if (!ret)
-		INIT_LIST_HEAD(&mtk->bw_ep_chk_list);
+		list_del_init(&mtk->bw_ep_chk_list);
 
 	return ret;
 }
@@ -824,8 +815,8 @@
 	if (ret)
 		return ret;
 
-	if (ep->hcpriv)
-		drop_ep_quirk(hcd, udev, ep);
+	/* needn't check @ep->hcpriv, xhci_endpoint_disable set it NULL */
+	drop_ep_quirk(hcd, udev, ep);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-mtk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-mtk.c
@@ -7,6 +7,7 @@
  *  Chunfeng Yun <chunfeng.yun@mediatek.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/dma-mapping.h>
 #include <linux/iopoll.h>
 #include <linux/kernel.h>
@@ -72,6 +73,9 @@
 #define FRMCNT_LEV1_RANG	(0x12b << 8)
 #define FRMCNT_LEV1_RANG_MASK	GENMASK(19, 8)
 
+#define HSCH_CFG1		0x960
+#define SCH3_RXFIFO_DEPTH_MASK	GENMASK(21, 20)
+
 #define SS_GEN2_EOF_CFG		0x990
 #define SSG2EOF_OFFSET		0x3c
 
@@ -100,6 +104,8 @@
 #define SSC_IP_SLEEP_EN	BIT(4)
 #define SSC_SPM_INT_EN		BIT(1)
 
+#define SCH_FIFO_TO_KB(x)	((x) >> 10)
+
 enum ssusb_uwk_vers {
 	SSUSB_UWK_V1 = 1,
 	SSUSB_UWK_V2,
@@ -147,6 +153,35 @@
 	writel(value, hcd->regs + SS_GEN2_EOF_CFG);
 }
 
+/*
+ * workaround: usb3.2 gen1 isoc rx hw issue
+ * host send out unexpected ACK afer device fininsh a burst transfer with
+ * a short packet.
+ */
+static void xhci_mtk_rxfifo_depth_set(struct xhci_hcd_mtk *mtk)
+{
+	struct usb_hcd *hcd = mtk->hcd;
+	u32 value;
+
+	if (!mtk->rxfifo_depth)
+		return;
+
+	value = readl(hcd->regs + HSCH_CFG1);
+	value &= ~SCH3_RXFIFO_DEPTH_MASK;
+	value |= FIELD_PREP(SCH3_RXFIFO_DEPTH_MASK,
+			    SCH_FIFO_TO_KB(mtk->rxfifo_depth) - 1);
+	writel(value, hcd->regs + HSCH_CFG1);
+}
+
+static void xhci_mtk_init_quirk(struct xhci_hcd_mtk *mtk)
+{
+	/* workaround only for mt8195 */
+	xhci_mtk_set_frame_interval(mtk);
+
+	/* workaround for SoCs using SSUSB about before IPM v1.6.0 */
+	xhci_mtk_rxfifo_depth_set(mtk);
+}
+
 static int xhci_mtk_host_enable(struct xhci_hcd_mtk *mtk)
 {
 	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
@@ -429,8 +464,7 @@
 		if (ret)
 			return ret;
 
-		/* workaround only for mt8195 */
-		xhci_mtk_set_frame_interval(mtk);
+		xhci_mtk_init_quirk(mtk);
 	}
 
 	ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
@@ -517,6 +551,8 @@
 	of_property_read_u32(node, "mediatek,u2p-dis-msk",
 			     &mtk->u2p_dis_msk);
 
+	of_property_read_u32(node, "rx-fifo-depth", &mtk->rxfifo_depth);
+
 	ret = usb_wakeup_of_property_parse(mtk, node);
 	if (ret) {
 		dev_err(dev, "failed to parse uwk property\n");
@@ -570,6 +606,7 @@
 	}
 
 	device_init_wakeup(dev, true);
+	dma_set_max_seg_size(dev, UINT_MAX);
 
 	xhci = hcd_to_xhci(hcd);
 	xhci->main_hcd = hcd;
@@ -619,7 +656,6 @@
 
 dealloc_usb3_hcd:
 	usb_remove_hcd(xhci->shared_hcd);
-	xhci->shared_hcd = NULL;
 
 dealloc_usb2_hcd:
 	usb_remove_hcd(hcd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-mtk.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-mtk.h
@@ -161,6 +161,8 @@
 	struct regmap *uwk;
 	u32 uwk_reg_base;
 	u32 uwk_vers;
+	/* quirk */
+	u32 rxfifo_depth;
 };
 
 static inline struct xhci_hcd_mtk *hcd_to_mtk(struct usb_hcd *hcd)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-mvebu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-mvebu.c
@@ -33,7 +33,7 @@
 
 	/* Program each DRAM CS in a seperate window */
 	for (win = 0; win < dram->num_cs; win++) {
-		const struct mbus_dram_window *cs = dram->cs + win;
+		const struct mbus_dram_window *cs = &dram->cs[win];
 
 		writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
 		       (dram->mbus_dram_target_id << 4) | 1,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-pci.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/acpi.h>
 #include <linux/reset.h>
+#include <linux/suspend.h>
 
 #include "xhci.h"
 #include "xhci-trace.h"
@@ -27,17 +28,20 @@
 #define SPARSE_CNTL_ENABLE	0xC12C
 
 /* Device for a quirk */
-#define PCI_VENDOR_ID_FRESCO_LOGIC	0x1b73
-#define PCI_DEVICE_ID_FRESCO_LOGIC_PDK	0x1000
+#define PCI_VENDOR_ID_FRESCO_LOGIC		0x1b73
+#define PCI_DEVICE_ID_FRESCO_LOGIC_PDK		0x1000
 #define PCI_DEVICE_ID_FRESCO_LOGIC_FL1009	0x1009
 #define PCI_DEVICE_ID_FRESCO_LOGIC_FL1100	0x1100
 #define PCI_DEVICE_ID_FRESCO_LOGIC_FL1400	0x1400
 
 #define PCI_VENDOR_ID_ETRON		0x1b6f
 #define PCI_DEVICE_ID_EJ168		0x7023
+#define PCI_DEVICE_ID_EJ188		0x7052
 
-#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI	0x8c31
-#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI	0x9c31
+#define PCI_DEVICE_ID_VIA_VL805			0x3483
+
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI		0x8c31
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI		0x9c31
 #define PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_XHCI	0x9cb1
 #define PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI		0x22b5
 #define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI		0xa12f
@@ -58,27 +62,36 @@
 #define PCI_DEVICE_ID_INTEL_CML_XHCI			0xa3af
 #define PCI_DEVICE_ID_INTEL_TIGER_LAKE_XHCI		0x9a13
 #define PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_XHCI		0x1138
-#define PCI_DEVICE_ID_INTEL_ALDER_LAKE_XHCI		0x461e
+#define PCI_DEVICE_ID_INTEL_ALDER_LAKE_PCH_XHCI		0x51ed
+#define PCI_DEVICE_ID_INTEL_ALDER_LAKE_N_PCH_XHCI	0x54ed
 
 #define PCI_DEVICE_ID_AMD_RENOIR_XHCI			0x1639
 #define PCI_DEVICE_ID_AMD_PROMONTORYA_4			0x43b9
 #define PCI_DEVICE_ID_AMD_PROMONTORYA_3			0x43ba
 #define PCI_DEVICE_ID_AMD_PROMONTORYA_2			0x43bb
 #define PCI_DEVICE_ID_AMD_PROMONTORYA_1			0x43bc
+
 #define PCI_DEVICE_ID_ASMEDIA_1042_XHCI			0x1042
 #define PCI_DEVICE_ID_ASMEDIA_1042A_XHCI		0x1142
 #define PCI_DEVICE_ID_ASMEDIA_1142_XHCI			0x1242
 #define PCI_DEVICE_ID_ASMEDIA_2142_XHCI			0x2142
+#define PCI_DEVICE_ID_ASMEDIA_3042_XHCI			0x3042
 #define PCI_DEVICE_ID_ASMEDIA_3242_XHCI			0x3242
 
+#define PCI_DEVICE_ID_CADENCE				0x17CD
+#define PCI_DEVICE_ID_CADENCE_SSP			0x0200
+
 static const char hcd_name[] = "xhci_hcd";
 
 static struct hc_driver __read_mostly xhci_pci_hc_driver;
 
 static int xhci_pci_setup(struct usb_hcd *hcd);
+static int xhci_pci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
+				      struct usb_tt *tt, gfp_t mem_flags);
 
 static const struct xhci_driver_overrides xhci_pci_overrides __initconst = {
 	.reset = xhci_pci_setup,
+	.update_hub_device = xhci_pci_update_hub_device,
 };
 
 /* called after powerup, by probe or system-pm "wakeup" */
@@ -114,7 +127,6 @@
 	/* Look for vendor-specific quirks */
 	if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
 			(pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK ||
-			 pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1100 ||
 			 pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1400)) {
 		if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
 				pdev->revision == 0x0) {
@@ -149,6 +161,10 @@
 			pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1009)
 		xhci->quirks |= XHCI_BROKEN_STREAMS;
 
+	if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
+			pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1100)
+		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
+
 	if (pdev->vendor == PCI_VENDOR_ID_NEC)
 		xhci->quirks |= XHCI_NEC_HOST;
 
@@ -187,7 +203,7 @@
 
 	if (pdev->vendor == PCI_VENDOR_ID_AMD &&
 		pdev->device == PCI_DEVICE_ID_AMD_RENOIR_XHCI)
-		xhci->quirks |= XHCI_BROKEN_D3COLD;
+		xhci->quirks |= XHCI_BROKEN_D3COLD_S2I;
 
 	if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
 		xhci->quirks |= XHCI_LPM_SUPPORT;
@@ -243,6 +259,11 @@
 		xhci->quirks |= XHCI_MISSING_CAS;
 
 	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+	    (pdev->device == PCI_DEVICE_ID_INTEL_ALDER_LAKE_PCH_XHCI ||
+	     pdev->device == PCI_DEVICE_ID_INTEL_ALDER_LAKE_N_PCH_XHCI))
+		xhci->quirks |= XHCI_RESET_TO_DEFAULT;
+
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
 	    (pdev->device == PCI_DEVICE_ID_INTEL_ALPINE_RIDGE_2C_XHCI ||
 	     pdev->device == PCI_DEVICE_ID_INTEL_ALPINE_RIDGE_4C_XHCI ||
 	     pdev->device == PCI_DEVICE_ID_INTEL_ALPINE_RIDGE_LP_XHCI ||
@@ -253,8 +274,7 @@
 	     pdev->device == PCI_DEVICE_ID_INTEL_TITAN_RIDGE_DD_XHCI ||
 	     pdev->device == PCI_DEVICE_ID_INTEL_ICE_LAKE_XHCI ||
 	     pdev->device == PCI_DEVICE_ID_INTEL_TIGER_LAKE_XHCI ||
-	     pdev->device == PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_XHCI ||
-	     pdev->device == PCI_DEVICE_ID_INTEL_ALDER_LAKE_XHCI))
+	     pdev->device == PCI_DEVICE_ID_INTEL_MAPLE_RIDGE_XHCI))
 		xhci->quirks |= XHCI_DEFAULT_PM_RUNTIME_ALLOW;
 
 	if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
@@ -263,6 +283,12 @@
 		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
 		xhci->quirks |= XHCI_BROKEN_STREAMS;
 	}
+	if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
+			pdev->device == PCI_DEVICE_ID_EJ188) {
+		xhci->quirks |= XHCI_RESET_ON_RESUME;
+		xhci->quirks |= XHCI_BROKEN_STREAMS;
+	}
+
 	if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
 	    pdev->device == 0x0014) {
 		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
@@ -281,14 +307,20 @@
 			pdev->device == 0x3432)
 		xhci->quirks |= XHCI_BROKEN_STREAMS;
 
-	if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == 0x3483) {
+	if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == PCI_DEVICE_ID_VIA_VL805) {
 		xhci->quirks |= XHCI_LPM_SUPPORT;
-		xhci->quirks |= XHCI_EP_CTX_BROKEN_DCS;
+		xhci->quirks |= XHCI_TRB_OVERFETCH;
 	}
 
 	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
-		pdev->device == PCI_DEVICE_ID_ASMEDIA_1042_XHCI)
+		pdev->device == PCI_DEVICE_ID_ASMEDIA_1042_XHCI) {
+		/*
+		 * try to tame the ASMedia 1042 controller which reports 0.96
+		 * but appears to behave more like 1.0
+		 */
+		xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
 		xhci->quirks |= XHCI_BROKEN_STREAMS;
+	}
 	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
 		pdev->device == PCI_DEVICE_ID_ASMEDIA_1042A_XHCI) {
 		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
@@ -304,6 +336,10 @@
 		pdev->device == PCI_DEVICE_ID_ASMEDIA_1042A_XHCI)
 		xhci->quirks |= XHCI_ASMEDIA_MODIFY_FLOWCONTROL;
 
+	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
+	    pdev->device == PCI_DEVICE_ID_ASMEDIA_3042_XHCI)
+		xhci->quirks |= XHCI_RESET_ON_RESUME;
+
 	if (pdev->vendor == PCI_VENDOR_ID_TI && pdev->device == 0x8241)
 		xhci->quirks |= XHCI_LIMIT_ENDPOINT_INTERVAL_7;
 
@@ -317,6 +353,26 @@
 	     pdev->device == PCI_DEVICE_ID_AMD_PROMONTORYA_4))
 		xhci->quirks |= XHCI_NO_SOFT_RETRY;
 
+	if (pdev->vendor == PCI_VENDOR_ID_ZHAOXIN) {
+		xhci->quirks |= XHCI_ZHAOXIN_HOST;
+
+		if (pdev->device == 0x9202) {
+			xhci->quirks |= XHCI_RESET_ON_RESUME;
+			xhci->quirks |= XHCI_TRB_OVERFETCH;
+		}
+
+		if (pdev->device == 0x9203)
+			xhci->quirks |= XHCI_TRB_OVERFETCH;
+	}
+
+	if (pdev->vendor == PCI_DEVICE_ID_CADENCE &&
+	    pdev->device == PCI_DEVICE_ID_CADENCE_SSP)
+		xhci->quirks |= XHCI_CDNS_SCTX_QUIRK;
+
+	/* xHC spec requires PCI devices to support D3hot and D3cold */
+	if (xhci->hci_version >= 0x120)
+		xhci->quirks |= XHCI_DEFAULT_PM_RUNTIME_ALLOW;
+
 	if (xhci->quirks & XHCI_RESET_ON_RESUME)
 		xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
 				"QUIRK: Resetting on resume");
@@ -334,8 +390,38 @@
 				NULL);
 	ACPI_FREE(obj);
 }
+
+static void xhci_find_lpm_incapable_ports(struct usb_hcd *hcd, struct usb_device *hdev)
+{
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+	struct xhci_hub *rhub = &xhci->usb3_rhub;
+	int ret;
+	int i;
+
+	/* This is not the usb3 roothub we are looking for */
+	if (hcd != rhub->hcd)
+		return;
+
+	if (hdev->maxchild > rhub->num_ports) {
+		dev_err(&hdev->dev, "USB3 roothub port number mismatch\n");
+		return;
+	}
+
+	for (i = 0; i < hdev->maxchild; i++) {
+		ret = usb_acpi_port_lpm_incapable(hdev, i);
+
+		dev_dbg(&hdev->dev, "port-%d disable U1/U2 _DSM: %d\n", i + 1, ret);
+
+		if (ret >= 0) {
+			rhub->ports[i]->lpm_incapable = ret;
+			continue;
+		}
+	}
+}
+
 #else
 static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { }
+static void xhci_find_lpm_incapable_ports(struct usb_hcd *hcd, struct usb_device *hdev) { }
 #endif /* CONFIG_ACPI */
 
 /* called during probe() after chip reset completes */
@@ -368,6 +454,16 @@
 	return xhci_pci_reinit(xhci, pdev);
 }
 
+static int xhci_pci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
+				      struct usb_tt *tt, gfp_t mem_flags)
+{
+	/* Check if acpi claims some USB3 roothub ports are lpm incapable */
+	if (!hdev->parent)
+		xhci_find_lpm_incapable_ports(hcd, hdev);
+
+	return xhci_update_hub_device(hcd, hdev, tt, mem_flags);
+}
+
 /*
  * We need to register our own PCI probe function (instead of the USB core's
  * function) in order to create a second roothub under xHCI.
@@ -410,6 +506,15 @@
 	hcd = dev_get_drvdata(&dev->dev);
 	xhci = hcd_to_xhci(hcd);
 	xhci->reset = reset;
+
+	if (xhci->quirks & XHCI_DISABLE_SPARSE) {
+		u32 reg;
+
+		reg = readl(hcd->regs + 0xC12C);
+		reg &=  ~BIT(17);
+		writel(reg, hcd->regs + 0xC12C);
+	}
+
 	xhci->shared_hcd = usb_create_shared_hcd(&xhci_pci_hc_driver, &dev->dev,
 						 pci_name(dev), hcd);
 	if (!xhci->shared_hcd) {
@@ -434,9 +539,13 @@
 	/* USB-2 and USB-3 roothubs initialized, allow runtime pm suspend */
 	pm_runtime_put_noidle(&dev->dev);
 
-	if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
+	if (pci_choose_state(dev, PMSG_SUSPEND) == PCI_D0)
+		pm_runtime_get(&dev->dev);
+	else if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
 		pm_runtime_allow(&dev->dev);
 
+	dma_set_max_seg_size(&dev->dev, UINT_MAX);
+
 	return 0;
 
 put_usb3_hcd:
@@ -451,12 +560,16 @@
 static void xhci_pci_remove(struct pci_dev *dev)
 {
 	struct xhci_hcd *xhci;
+	bool set_power_d3;
 
 	xhci = hcd_to_xhci(pci_get_drvdata(dev));
+	set_power_d3 = xhci->quirks & XHCI_SPURIOUS_WAKEUP;
 
 	xhci->xhc_state |= XHCI_STATE_REMOVING;
 
-	if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
+	if (pci_choose_state(dev, PMSG_SUSPEND) == PCI_D0)
+		pm_runtime_put(&dev->dev);
+	else if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
 		pm_runtime_forbid(&dev->dev);
 
 	if (xhci->shared_hcd) {
@@ -465,11 +578,11 @@
 		xhci->shared_hcd = NULL;
 	}
 
+	usb_hcd_pci_remove(dev);
+
 	/* Workaround for spurious wakeups at shutdown with HSW */
-	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+	if (set_power_d3)
 		pci_set_power_state(dev, PCI_D3hot);
-
-	usb_hcd_pci_remove(dev);
 }
 
 #ifdef CONFIG_PM
@@ -546,9 +659,16 @@
 	 * Systems with the TI redriver that loses port status change events
 	 * need to have the registers polled during D3, so avoid D3cold.
 	 */
-	if (xhci->quirks & (XHCI_COMP_MODE_QUIRK | XHCI_BROKEN_D3COLD))
+	if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
 		pci_d3cold_disable(pdev);
 
+#ifdef CONFIG_SUSPEND
+	/* d3cold is broken, but only when s2idle is used */
+	if (pm_suspend_target_state == PM_SUSPEND_TO_IDLE &&
+	    xhci->quirks & (XHCI_BROKEN_D3COLD_S2I))
+		pci_d3cold_disable(pdev);
+#endif
+
 	if (xhci->quirks & XHCI_PME_STUCK_QUIRK)
 		xhci_pme_quirk(hcd);
 
@@ -657,11 +777,9 @@
 	/* suspend and resume implemented later */
 
 	.shutdown = 	usb_hcd_pci_shutdown,
-#ifdef CONFIG_PM
 	.driver = {
-		.pm = &usb_hcd_pci_pm_ops
+		.pm = pm_ptr(&usb_hcd_pci_pm_ops),
 	},
-#endif
 };
 
 static int __init xhci_pci_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-plat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-plat.c
@@ -19,6 +19,7 @@
 #include <linux/slab.h>
 #include <linux/acpi.h>
 #include <linux/usb/of.h>
+#include <linux/usb/otg.h>
 
 #include "xhci.h"
 #include "xhci-plat.h"
@@ -30,6 +31,8 @@
 static int xhci_plat_setup(struct usb_hcd *hcd);
 static int xhci_plat_start(struct usb_hcd *hcd);
 
+static host_wakeup_t host_wakeup_fn;
+
 static const struct xhci_driver_overrides xhci_plat_overrides __initconst = {
 	.extra_priv_size = sizeof(struct xhci_plat_priv),
 	.reset = xhci_plat_setup,
@@ -96,6 +99,17 @@
 	xhci->quirks |= XHCI_PLAT | priv->quirks;
 }
 
+static void host_wakeup_register(host_wakeup_t func)
+{
+	host_wakeup_fn = func;
+}
+
+static void host_wakeup_capable(struct device *dev, bool wakeup)
+{
+	if (host_wakeup_fn)
+		host_wakeup_fn(dev, wakeup);
+}
+
 /* called during probe() after chip reset completes */
 static int xhci_plat_setup(struct usb_hcd *hcd)
 {
@@ -134,7 +148,7 @@
 };
 
 static const struct xhci_plat_priv xhci_plat_brcm = {
-	.quirks = XHCI_RESET_ON_RESUME,
+	.quirks = XHCI_RESET_ON_RESUME | XHCI_SUSPEND_RESUME_CLKS,
 };
 
 static const struct of_device_id usb_xhci_of_match[] = {
@@ -184,6 +198,35 @@
 MODULE_DEVICE_TABLE(of, usb_xhci_of_match);
 #endif
 
+static int usb_otg_set_host(struct device *dev, struct usb_hcd *hcd, bool yes)
+{
+	int ret = 0;
+
+	hcd->usb_phy = usb_get_phy(USB_PHY_TYPE_USB3);
+	if (!IS_ERR_OR_NULL(hcd->usb_phy) && hcd->usb_phy->otg) {
+		if (yes) {
+			if (otg_set_host(hcd->usb_phy->otg, &hcd->self)) {
+				usb_put_phy(hcd->usb_phy);
+				goto disable_phy;
+			}
+		} else {
+			ret = otg_set_host(hcd->usb_phy->otg, NULL);
+			usb_put_phy(hcd->usb_phy);
+			goto disable_phy;
+		}
+
+	} else {
+		goto disable_phy;
+	}
+
+	return 0;
+
+disable_phy:
+	hcd->usb_phy = NULL;
+
+	return ret;
+}
+
 static int xhci_plat_probe(struct platform_device *pdev)
 {
 	const struct xhci_plat_priv *priv_match;
@@ -241,6 +284,9 @@
 			return ret;
 	}
 
+	/* Set the controller as wakeup capable */
+	device_set_wakeup_capable(&pdev->dev, true);
+
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 	pm_runtime_get_noresume(&pdev->dev);
@@ -299,6 +345,7 @@
 	}
 
 	device_set_wakeup_capable(&pdev->dev, true);
+	host_wakeup_register(dwc3_host_wakeup_capable);
 
 	xhci->main_hcd = hcd;
 	xhci->shared_hcd = __usb_create_hcd(driver, sysdev, &pdev->dev,
@@ -323,6 +370,12 @@
 		if (device_property_read_bool(tmpdev, "quirk-broken-port-ped"))
 			xhci->quirks |= XHCI_BROKEN_PORT_PED;
 
+		if (device_property_read_bool(tmpdev, "xhci-sg-trb-cache-size-quirk"))
+			xhci->quirks |= XHCI_SG_TRB_CACHE_SIZE_QUIRK;
+
+		if (device_property_read_bool(tmpdev, "xhci-reset-on-resume"))
+			xhci->quirks |= XHCI_RESET_ON_RESUME;
+
 		device_property_read_u32(tmpdev, "imod-interval-ns",
 					 &xhci->imod_interval);
 	}
@@ -365,6 +418,10 @@
 	if (ret)
 		goto dealloc_usb2_hcd;
 
+	ret = usb_otg_set_host(&pdev->dev, hcd, true);
+	if (ret)
+		goto dealloc_usb2_hcd;
+
 	device_enable_async_suspend(&pdev->dev);
 	pm_runtime_put_noidle(&pdev->dev);
 
@@ -417,6 +474,9 @@
 	xhci->shared_hcd = NULL;
 	usb_phy_shutdown(hcd->usb_phy);
 
+	host_wakeup_register(NULL);
+	usb_otg_set_host(&dev->dev, hcd, false);
+
 	usb_remove_hcd(hcd);
 	usb_put_hcd(shared_hcd);
 
@@ -437,14 +497,35 @@
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
 	int ret;
 
+	if (pm_runtime_suspended(dev))
+		pm_runtime_resume(dev);
+
 	ret = xhci_priv_suspend_quirk(hcd);
 	if (ret)
 		return ret;
+
+	/* Inform dwc3 driver about the device wakeup capability */
+	if (device_may_wakeup(&hcd->self.root_hub->dev)) {
+		host_wakeup_capable(dev, true);
+		enable_irq_wake(hcd->irq);
+	} else {
+		host_wakeup_capable(dev, false);
+	}
+
 	/*
 	 * xhci_suspend() needs `do_wakeup` to know whether host is allowed
 	 * to do wakeup during suspend.
 	 */
-	return xhci_suspend(xhci, device_may_wakeup(dev));
+	ret = xhci_suspend(xhci, device_may_wakeup(dev));
+	if (ret)
+		return ret;
+
+	if (!device_may_wakeup(dev) && (xhci->quirks & XHCI_SUSPEND_RESUME_CLKS)) {
+		clk_disable_unprepare(xhci->clk);
+		clk_disable_unprepare(xhci->reg_clk);
+	}
+
+	return 0;
 }
 
 static int __maybe_unused xhci_plat_resume(struct device *dev)
@@ -453,19 +534,39 @@
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
 	int ret;
 
+	if (!device_may_wakeup(dev) && (xhci->quirks & XHCI_SUSPEND_RESUME_CLKS)) {
+		ret = clk_prepare_enable(xhci->clk);
+		if (ret)
+			return ret;
+
+		ret = clk_prepare_enable(xhci->reg_clk);
+		if (ret) {
+			clk_disable_unprepare(xhci->clk);
+			return ret;
+		}
+	}
+
 	ret = xhci_priv_resume_quirk(hcd);
 	if (ret)
-		return ret;
+		goto disable_clks;
 
 	ret = xhci_resume(xhci, 0);
 	if (ret)
-		return ret;
+		goto disable_clks;
 
 	pm_runtime_disable(dev);
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
 
 	return 0;
+
+disable_clks:
+	if (!device_may_wakeup(dev) && (xhci->quirks & XHCI_SUSPEND_RESUME_CLKS)) {
+		clk_disable_unprepare(xhci->clk);
+		clk_disable_unprepare(xhci->reg_clk);
+	}
+
+	return ret;
 }
 
 static int __maybe_unused xhci_plat_runtime_suspend(struct device *dev)
@@ -486,6 +587,9 @@
 	struct usb_hcd  *hcd = dev_get_drvdata(dev);
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 
+	if (device_may_wakeup(&hcd->self.root_hub->dev))
+		disable_irq_wake(hcd->irq);
+
 	return xhci_resume(xhci, 0);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-plat.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-plat.h
@@ -8,7 +8,9 @@
 #ifndef _XHCI_PLAT_H
 #define _XHCI_PLAT_H
 
-#include "xhci.h"	/* for hcd_to_xhci() */
+struct device;
+struct platform_device;
+struct usb_hcd;
 
 struct xhci_plat_priv {
 	const char *firmware_name;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-port.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-port.h
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
+/* true: device connected */
+#define PORT_CONNECT	(1 << 0)
+/* true: port enabled */
+#define PORT_PE		(1 << 1)
+/* bit 2 reserved and zeroed */
+/* true: port has an over-current condition */
+#define PORT_OC		(1 << 3)
+/* true: port reset signaling asserted */
+#define PORT_RESET	(1 << 4)
+/* Port Link State - bits 5:8
+ * A read gives the current link PM state of the port,
+ * a write with Link State Write Strobe set sets the link state.
+ */
+#define PORT_PLS_MASK	(0xf << 5)
+#define XDEV_U0		(0x0 << 5)
+#define XDEV_U1		(0x1 << 5)
+#define XDEV_U2		(0x2 << 5)
+#define XDEV_U3		(0x3 << 5)
+#define XDEV_DISABLED	(0x4 << 5)
+#define XDEV_RXDETECT	(0x5 << 5)
+#define XDEV_INACTIVE	(0x6 << 5)
+#define XDEV_POLLING	(0x7 << 5)
+#define XDEV_RECOVERY	(0x8 << 5)
+#define XDEV_HOT_RESET	(0x9 << 5)
+#define XDEV_COMP_MODE	(0xa << 5)
+#define XDEV_TEST_MODE	(0xb << 5)
+#define XDEV_RESUME	(0xf << 5)
+
+/* true: port has power (see HCC_PPC) */
+#define PORT_POWER	(1 << 9)
+/* bits 10:13 indicate device speed:
+ * 0 - undefined speed - port hasn't be initialized by a reset yet
+ * 1 - full speed
+ * 2 - low speed
+ * 3 - high speed
+ * 4 - super speed
+ * 5-15 reserved
+ */
+#define DEV_SPEED_MASK		(0xf << 10)
+#define	XDEV_FS			(0x1 << 10)
+#define	XDEV_LS			(0x2 << 10)
+#define	XDEV_HS			(0x3 << 10)
+#define	XDEV_SS			(0x4 << 10)
+#define	XDEV_SSP		(0x5 << 10)
+#define DEV_UNDEFSPEED(p)	(((p) & DEV_SPEED_MASK) == (0x0<<10))
+#define DEV_FULLSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_FS)
+#define DEV_LOWSPEED(p)		(((p) & DEV_SPEED_MASK) == XDEV_LS)
+#define DEV_HIGHSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_HS)
+#define DEV_SUPERSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_SS)
+#define DEV_SUPERSPEEDPLUS(p)	(((p) & DEV_SPEED_MASK) == XDEV_SSP)
+#define DEV_SUPERSPEED_ANY(p)	(((p) & DEV_SPEED_MASK) >= XDEV_SS)
+#define DEV_PORT_SPEED(p)	(((p) >> 10) & 0x0f)
+
+/* Bits 20:23 in the Slot Context are the speed for the device */
+#define	SLOT_SPEED_FS		(XDEV_FS << 10)
+#define	SLOT_SPEED_LS		(XDEV_LS << 10)
+#define	SLOT_SPEED_HS		(XDEV_HS << 10)
+#define	SLOT_SPEED_SS		(XDEV_SS << 10)
+#define	SLOT_SPEED_SSP		(XDEV_SSP << 10)
+/* Port Indicator Control */
+#define PORT_LED_OFF	(0 << 14)
+#define PORT_LED_AMBER	(1 << 14)
+#define PORT_LED_GREEN	(2 << 14)
+#define PORT_LED_MASK	(3 << 14)
+/* Port Link State Write Strobe - set this when changing link state */
+#define PORT_LINK_STROBE	(1 << 16)
+/* true: connect status change */
+#define PORT_CSC	(1 << 17)
+/* true: port enable change */
+#define PORT_PEC	(1 << 18)
+/* true: warm reset for a USB 3.0 device is done.  A "hot" reset puts the port
+ * into an enabled state, and the device into the default state.  A "warm" reset
+ * also resets the link, forcing the device through the link training sequence.
+ * SW can also look at the Port Reset register to see when warm reset is done.
+ */
+#define PORT_WRC	(1 << 19)
+/* true: over-current change */
+#define PORT_OCC	(1 << 20)
+/* true: reset change - 1 to 0 transition of PORT_RESET */
+#define PORT_RC		(1 << 21)
+/* port link status change - set on some port link state transitions:
+ *  Transition				Reason
+ *  ------------------------------------------------------------------------------
+ *  - U3 to Resume			Wakeup signaling from a device
+ *  - Resume to Recovery to U0		USB 3.0 device resume
+ *  - Resume to U0			USB 2.0 device resume
+ *  - U3 to Recovery to U0		Software resume of USB 3.0 device complete
+ *  - U3 to U0				Software resume of USB 2.0 device complete
+ *  - U2 to U0				L1 resume of USB 2.1 device complete
+ *  - U0 to U0 (???)			L1 entry rejection by USB 2.1 device
+ *  - U0 to disabled			L1 entry error with USB 2.1 device
+ *  - Any state to inactive		Error on USB 3.0 port
+ */
+#define PORT_PLC	(1 << 22)
+/* port configure error change - port failed to configure its link partner */
+#define PORT_CEC	(1 << 23)
+#define PORT_CHANGE_MASK	(PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
+				 PORT_RC | PORT_PLC | PORT_CEC)
+
+
+/* Cold Attach Status - xHC can set this bit to report device attached during
+ * Sx state. Warm port reset should be perfomed to clear this bit and move port
+ * to connected state.
+ */
+#define PORT_CAS	(1 << 24)
+/* wake on connect (enable) */
+#define PORT_WKCONN_E	(1 << 25)
+/* wake on disconnect (enable) */
+#define PORT_WKDISC_E	(1 << 26)
+/* wake on over-current (enable) */
+#define PORT_WKOC_E	(1 << 27)
+/* bits 28:29 reserved */
+/* true: device is non-removable - for USB 3.0 roothub emulation */
+#define PORT_DEV_REMOVE	(1 << 30)
+/* Initiate a warm port reset - complete when PORT_WRC is '1' */
+#define PORT_WR		(1 << 31)
+
+/* We mark duplicate entries with -1 */
+#define DUPLICATE_ENTRY ((u8)(-1))
+
+/* Port Power Management Status and Control - port_power_base bitmasks */
+/* Inactivity timer value for transitions into U1, in microseconds.
+ * Timeout can be up to 127us.  0xFF means an infinite timeout.
+ */
+#define PORT_U1_TIMEOUT(p)	((p) & 0xff)
+#define PORT_U1_TIMEOUT_MASK	0xff
+/* Inactivity timer value for transitions into U2 */
+#define PORT_U2_TIMEOUT(p)	(((p) & 0xff) << 8)
+#define PORT_U2_TIMEOUT_MASK	(0xff << 8)
+/* Bits 24:31 for port testing */
+
+/* USB2 Protocol PORTSPMSC */
+#define	PORT_L1S_MASK		7
+#define	PORT_L1S_SUCCESS	1
+#define	PORT_RWE		(1 << 3)
+#define	PORT_HIRD(p)		(((p) & 0xf) << 4)
+#define	PORT_HIRD_MASK		(0xf << 4)
+#define	PORT_L1DS_MASK		(0xff << 8)
+#define	PORT_L1DS(p)		(((p) & 0xff) << 8)
+#define	PORT_HLE		(1 << 16)
+#define PORT_TEST_MODE_SHIFT	28
+
+/* USB3 Protocol PORTLI  Port Link Information */
+#define PORT_RX_LANES(p)	(((p) >> 16) & 0xf)
+#define PORT_TX_LANES(p)	(((p) >> 20) & 0xf)
+
+/* USB2 Protocol PORTHLPMC */
+#define PORT_HIRDM(p)((p) & 3)
+#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
+#define PORT_BESLD(p)(((p) & 0xf) << 10)
+
+/* use 512 microseconds as USB2 LPM L1 default timeout. */
+#define XHCI_L1_TIMEOUT		512
+
+/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
+ * Safe to use with mixed HIRD and BESL systems (host and device) and is used
+ * by other operating systems.
+ *
+ * XHCI 1.0 errata 8/14/12 Table 13 notes:
+ * "Software should choose xHC BESL/BESLD field values that do not violate a
+ * device's resume latency requirements,
+ * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
+ * or not program values < '4' if BLC = '0' and a BESL device is attached.
+ */
+#define XHCI_DEFAULT_BESL	4
+
+/*
+ * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
+ * to complete link training. usually link trainig completes much faster
+ * so check status 10 times with 36ms sleep in places we need to wait for
+ * polling to complete.
+ */
+#define XHCI_PORT_POLLING_LFPS_TIME  36
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-rcar.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-rcar.c
@@ -75,7 +75,6 @@
 
 /* For soc_device_attribute */
 #define RCAR_XHCI_FIRMWARE_V2   BIT(0) /* FIRMWARE V2 */
-#define RCAR_XHCI_FIRMWARE_V3   BIT(1) /* FIRMWARE V3 */
 
 static const struct soc_device_attribute rcar_quirks_match[]  = {
 	{
@@ -147,8 +146,6 @@
 
 	if (quirks & RCAR_XHCI_FIRMWARE_V2)
 		firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2;
-	else if (quirks & RCAR_XHCI_FIRMWARE_V3)
-		firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3;
 	else
 		firmware_name = priv->firmware_name;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-ring.c
@@ -52,6 +52,7 @@
  *   endpoint rings; it generates events on the event ring for these.
  */
 
+#include <linux/jiffies.h>
 #include <linux/scatterlist.h>
 #include <linux/slab.h>
 #include <linux/dma-mapping.h>
@@ -276,6 +277,26 @@
 	trace_xhci_inc_enq(ring);
 }
 
+static int xhci_num_trbs_to(struct xhci_segment *start_seg, union xhci_trb *start,
+			    struct xhci_segment *end_seg, union xhci_trb *end,
+			    unsigned int num_segs)
+{
+	union xhci_trb *last_on_seg;
+	int num = 0;
+	int i = 0;
+
+	do {
+		if (start_seg == end_seg && end >= start)
+			return num + (end - start);
+		last_on_seg = &start_seg->trbs[TRBS_PER_SEGMENT - 1];
+		num += last_on_seg - start;
+		start_seg = start_seg->next;
+		start = start_seg->trbs;
+	} while (i++ <= num_segs);
+
+	return -EINVAL;
+}
+
 /*
  * Check to see if there's room to enqueue num_trbs on the ring and make sure
  * enqueue pointer will not advance into dequeue segment. See rules above.
@@ -312,9 +333,10 @@
 	readl(&xhci->dba->doorbell[0]);
 }
 
-static bool xhci_mod_cmd_timer(struct xhci_hcd *xhci, unsigned long delay)
+static bool xhci_mod_cmd_timer(struct xhci_hcd *xhci)
 {
-	return mod_delayed_work(system_wq, &xhci->cmd_timer, delay);
+	return mod_delayed_work(system_wq, &xhci->cmd_timer,
+			msecs_to_jiffies(xhci->current_cmd->timeout_ms));
 }
 
 static struct xhci_command *xhci_next_queued_cmd(struct xhci_hcd *xhci)
@@ -358,7 +380,8 @@
 	if ((xhci->cmd_ring->dequeue != xhci->cmd_ring->enqueue) &&
 	    !(xhci->xhc_state & XHCI_STATE_DYING)) {
 		xhci->current_cmd = cur_cmd;
-		xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT);
+		if (cur_cmd)
+			xhci_mod_cmd_timer(xhci);
 		xhci_ring_cmd_db(xhci);
 	}
 }
@@ -366,7 +389,9 @@
 /* Must be called with xhci->lock held, releases and aquires lock back */
 static int xhci_abort_cmd_ring(struct xhci_hcd *xhci, unsigned long flags)
 {
-	u32 temp_32;
+	struct xhci_segment *new_seg	= xhci->cmd_ring->deq_seg;
+	union xhci_trb *new_deq		= xhci->cmd_ring->dequeue;
+	u64 crcr;
 	int ret;
 
 	xhci_dbg(xhci, "Abort command ring\n");
@@ -375,13 +400,18 @@
 
 	/*
 	 * The control bits like command stop, abort are located in lower
-	 * dword of the command ring control register. Limit the write
-	 * to the lower dword to avoid corrupting the command ring pointer
-	 * in case if the command ring is stopped by the time upper dword
-	 * is written.
-	 */
-	temp_32 = readl(&xhci->op_regs->cmd_ring);
-	writel(temp_32 | CMD_RING_ABORT, &xhci->op_regs->cmd_ring);
+	 * dword of the command ring control register.
+	 * Some controllers require all 64 bits to be written to abort the ring.
+	 * Make sure the upper dword is valid, pointing to the next command,
+	 * avoiding corrupting the command ring pointer in case the command ring
+	 * is stopped by the time the upper dword is written.
+	 */
+	next_trb(xhci, NULL, &new_seg, &new_deq);
+	if (trb_is_link(new_deq))
+		next_trb(xhci, NULL, &new_seg, &new_deq);
+
+	crcr = xhci_trb_virt_to_dma(new_seg, new_deq);
+	xhci_write_64(xhci, crcr | CMD_RING_ABORT, &xhci->op_regs->cmd_ring);
 
 	/* Section 4.6.1.2 of xHCI 1.0 spec says software should also time the
 	 * completion of the Command Abort operation. If CRR is not negated in 5
@@ -565,11 +595,8 @@
 	struct xhci_ring *ep_ring;
 	struct xhci_command *cmd;
 	struct xhci_segment *new_seg;
-	struct xhci_segment *halted_seg = NULL;
 	union xhci_trb *new_deq;
 	int new_cycle;
-	union xhci_trb *halted_trb;
-	int index = 0;
 	dma_addr_t addr;
 	u64 hw_dequeue;
 	bool cycle_found = false;
@@ -607,27 +634,7 @@
 	hw_dequeue = xhci_get_hw_deq(xhci, dev, ep_index, stream_id);
 	new_seg = ep_ring->deq_seg;
 	new_deq = ep_ring->dequeue;
-
-	/*
-	 * Quirk: xHC write-back of the DCS field in the hardware dequeue
-	 * pointer is wrong - use the cycle state of the TRB pointed to by
-	 * the dequeue pointer.
-	 */
-	if (xhci->quirks & XHCI_EP_CTX_BROKEN_DCS &&
-	    !(ep->ep_state & EP_HAS_STREAMS))
-		halted_seg = trb_in_td(xhci, td->start_seg,
-				       td->first_trb, td->last_trb,
-				       hw_dequeue & ~0xf, false);
-	if (halted_seg) {
-		index = ((dma_addr_t)(hw_dequeue & ~0xf) - halted_seg->dma) /
-			 sizeof(*halted_trb);
-		halted_trb = &halted_seg->trbs[index];
-		new_cycle = halted_trb->generic.field[3] & 0x1;
-		xhci_dbg(xhci, "Endpoint DCS = %d TRB index = %d cycle = %d\n",
-			 (u8)(hw_dequeue & 0x1), index, new_cycle);
-	} else {
-		new_cycle = hw_dequeue & 0x1;
-	}
+	new_cycle = hw_dequeue & 0x1;
 
 	/*
 	 * We want to find the pointer, segment and cycle state of the new trb
@@ -768,7 +775,7 @@
 static void xhci_unmap_td_bounce_buffer(struct xhci_hcd *xhci,
 		struct xhci_ring *ring, struct xhci_td *td)
 {
-	struct device *dev = xhci_to_hcd(xhci)->self.controller;
+	struct device *dev = xhci_to_hcd(xhci)->self.sysdev;
 	struct xhci_segment *seg = td->bounce_seg;
 	struct urb *urb = td->urb;
 	size_t len;
@@ -841,7 +848,16 @@
 		/* set isoc urb status to 0 just as EHCI, UHCI, and OHCI */
 		if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS)
 			status = 0;
-		xhci_giveback_urb_in_irq(xhci, td, status);
+		if ((xhci->quirks & XHCI_STREAM_QUIRK) &&
+		    (ep_ring->stream_timeout_handler == true)) {
+			/* We get here if stream timer time-out and stop
+			 * command is issued. Send urb status as -EAGAIN
+			 * so that the same urb can be re-submitted.
+			 */
+			xhci_giveback_urb_in_irq(xhci, td, -EAGAIN);
+			ep_ring->stream_timeout_handler = false;
+		} else
+			xhci_giveback_urb_in_irq(xhci, td, status);
 	}
 
 	return 0;
@@ -957,6 +973,13 @@
 	unsigned int		slot_id = ep->vdev->slot_id;
 	int			err;
 
+	/*
+	 * This is not going to work if the hardware is changing its dequeue
+	 * pointers as we look at them. Completion handler will call us later.
+	 */
+	if (ep->ep_state & SET_DEQ_PENDING)
+		return 0;
+
 	xhci = ep->xhci;
 
 	list_for_each_entry_safe(td, tmp_td, &ep->cancelled_td_list, cancelled_td_list) {
@@ -990,13 +1013,27 @@
 				break;
 			case TD_DIRTY: /* TD is cached, clear it */
 			case TD_HALTED:
+			case TD_CLEARING_CACHE_DEFERRED:
+				if (cached_td) {
+					if (cached_td->urb->stream_id != td->urb->stream_id) {
+						/* Multiple streams case, defer move dq */
+						xhci_dbg(xhci,
+							 "Move dq deferred: stream %u URB %p\n",
+							 td->urb->stream_id, td->urb);
+						td->cancel_status = TD_CLEARING_CACHE_DEFERRED;
+						break;
+					}
+
+					/* Should never happen, but clear the TD if it does */
+					xhci_warn(xhci,
+						  "Found multiple active URBs %p and %p in stream %u?\n",
+						  td->urb, cached_td->urb,
+						  td->urb->stream_id);
+					td_to_noop(xhci, ring, cached_td, false);
+					cached_td->cancel_status = TD_CLEARED;
+				}
+				td_to_noop(xhci, ring, td, false);
 				td->cancel_status = TD_CLEARING_CACHE;
-				if (cached_td)
-					/* FIXME  stream case, several stopped rings */
-					xhci_dbg(xhci,
-						 "Move dq past stream %u URB %p instead of stream %u URB %p\n",
-						 td->urb->stream_id, td->urb,
-						 cached_td->urb->stream_id, cached_td->urb);
 				cached_td = td;
 				break;
 			}
@@ -1016,10 +1053,16 @@
 	if (err) {
 		/* Failed to move past cached td, just set cached TDs to no-op */
 		list_for_each_entry_safe(td, tmp_td, &ep->cancelled_td_list, cancelled_td_list) {
-			if (td->cancel_status != TD_CLEARING_CACHE)
+			/*
+			 * Deferred TDs need to have the deq pointer set after the above command
+			 * completes, so if that failed we just give up on all of them (and
+			 * complain loudly since this could cause issues due to caching).
+			 */
+			if (td->cancel_status != TD_CLEARING_CACHE &&
+			    td->cancel_status != TD_CLEARING_CACHE_DEFERRED)
 				continue;
-			xhci_dbg(xhci, "Failed to clear cancelled cached URB %p, mark clear anyway\n",
-				 td->urb);
+			xhci_warn(xhci, "Failed to clear cancelled cached URB %p, mark clear anyway\n",
+				  td->urb);
 			td_to_noop(xhci, ring, td, false);
 			td->cancel_status = TD_CLEARED;
 		}
@@ -1028,6 +1071,19 @@
 }
 
 /*
+ * Erase queued TDs from transfer ring(s) and give back those the xHC didn't
+ * stop on. If necessary, queue commands to move the xHC off cancelled TDs it
+ * stopped on. Those will be given back later when the commands complete.
+ *
+ * Call under xhci->lock on a stopped endpoint.
+ */
+void xhci_process_cancelled_tds(struct xhci_virt_ep *ep)
+{
+	xhci_invalidate_cancelled_tds(ep);
+	xhci_giveback_invalidated_tds(ep);
+}
+
+/*
  * Returns the TD the endpoint ring halted on.
  * Only call for non-running rings without streams.
  */
@@ -1117,9 +1173,35 @@
 				break;
 			xhci_stop_watchdog_timer_in_irq(xhci, ep);
 			return;
+		case EP_STATE_STOPPED:
+			/*
+			 * Per xHCI 4.6.9, Stop Endpoint command on a Stopped
+			 * EP is a Context State Error, and EP stays Stopped.
+			 *
+			 * But maybe it failed on Halted, and somebody ran Reset
+			 * Endpoint later. EP state is now Stopped and EP_HALTED
+			 * still set because Reset EP handler will run after us.
+			 */
+			if (ep->ep_state & EP_HALTED)
+				break;
+			/*
+			 * On some HCs EP state remains Stopped for some tens of
+			 * us to a few ms or more after a doorbell ring, and any
+			 * new Stop Endpoint fails without aborting the restart.
+			 * This handler may run quickly enough to still see this
+			 * Stopped state, but it will soon change to Running.
+			 *
+			 * Assume this bug on unexpected Stop Endpoint failures.
+			 * Keep retrying until the EP starts and stops again, on
+			 * chips where this is known to help. Wait for 100ms.
+			 */
+			if (time_is_before_jiffies(ep->stop_time + msecs_to_jiffies(100)))
+				break;
+			fallthrough;
 		case EP_STATE_RUNNING:
 			/* Race, HW handled stop ep cmd before ep was running */
-			xhci_dbg(xhci, "Stop ep completion ctx error, ep is running\n");
+			xhci_dbg(xhci, "Stop ep completion ctx error, ctx_state %d\n",
+					GET_EP_CTX_STATE(ep_ctx));
 
 			command = xhci_alloc_command(xhci, false, GFP_ATOMIC);
 			if (!command)
@@ -1171,7 +1253,10 @@
 	struct xhci_virt_ep *ep;
 	struct xhci_ring *ring;
 
-	ep = &xhci->devs[slot_id]->eps[ep_index];
+	ep = xhci_get_virt_ep(xhci, slot_id, ep_index);
+	if (!ep)
+		return;
+
 	if ((ep->ep_state & EP_HAS_STREAMS) ||
 			(ep->ep_state & EP_GETTING_NO_STREAMS)) {
 		int stream_id;
@@ -1241,6 +1326,84 @@
 		usb_hc_died(xhci_to_hcd(xhci));
 }
 
+/* This function is called when the stream ring timer gets timedout.
+ * dwc3 host controller has an issue where it doesn't process the BULK IN
+ * stream ring TD's(once in a while) even after ringing DoorBell for that
+ * stream ring. Because of this behaviour there will be no transfer events
+ * generated by the controller on the stream ring, resulting in the hang
+ * condition. xhci_stream_timeout() solves this issue by sending a stop
+ * command on the stream ring after stream timer gets timedout.
+ */
+void xhci_stream_timeout(struct timer_list *arg)
+{
+	struct xhci_hcd *xhci;
+	struct xhci_virt_ep *ep;
+	struct xhci_ring *ep_ring;
+	unsigned int slot_id, ep_index, stream_id;
+	struct xhci_td *td = NULL;
+	struct urb *urb = NULL;
+	struct urb_priv *urb_priv;
+	struct xhci_command *command;
+	unsigned long flags;
+	int i;
+
+	ep_ring = from_timer(ep_ring, arg, stream_timer);
+	xhci = ep_ring->xhci;
+
+	spin_lock_irqsave(&xhci->lock, flags);
+
+	if (!list_empty(&ep_ring->td_list)) {
+		td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list);
+		urb = td->urb;
+		urb_priv = urb->hcpriv;
+
+		slot_id = urb->dev->slot_id;
+		ep_index = xhci_get_endpoint_index(&urb->ep->desc);
+		stream_id = ep_ring->stream_id;
+		ep = &xhci->devs[slot_id]->eps[ep_index];
+		ep_ring->stream_timeout_handler = true;
+
+		/* Delete the stream ring timer */
+		del_timer(&ep_ring->stream_timer);
+
+		for (i = 0; i < urb_priv->num_tds; i++) {
+			td = &urb_priv->td[i];
+			list_add_tail(&td->cancelled_td_list,
+					&ep->cancelled_td_list);
+		}
+
+		/* Queue a stop endpoint command, but only if this is
+		 * the first cancellation to be handled.
+		 */
+		if (!(ep->ep_state & EP_STOP_CMD_PENDING)) {
+			command = xhci_alloc_command(xhci, false,
+					GFP_ATOMIC);
+			if (!command) {
+				xhci_warn(xhci,
+					"%s: Failed to allocate command\n",
+						__func__);
+				spin_unlock_irqrestore(&xhci->lock, flags);
+				return;
+			}
+
+			ep->ep_state |= EP_STOP_CMD_PENDING;
+			ep->stop_cmd_timer.expires = jiffies +
+				XHCI_STOP_EP_CMD_TIMEOUT * HZ;
+			add_timer(&ep->stop_cmd_timer);
+			xhci_queue_stop_endpoint(xhci, command,
+					urb->dev->slot_id, ep_index, 0);
+			xhci_ring_cmd_db(xhci);
+		}
+
+		spin_unlock_irqrestore(&xhci->lock, flags);
+		return;
+	}
+
+	spin_unlock_irqrestore(&xhci->lock, flags);
+	/* let the SCSI stack take care */
+	del_timer(&ep_ring->stream_timer);
+}
+
 /* Watchdog timer function for when a stop endpoint command fails to complete.
  * In this case, we assume the host controller is broken or dying or dead.  The
  * host may still be completing some other events, so we have to be careful to
@@ -1418,6 +1581,20 @@
 			struct xhci_stream_ctx *ctx =
 				&ep->stream_info->stream_ctx_array[stream_id];
 			deq = le64_to_cpu(ctx->stream_ring) & SCTX_DEQ_MASK;
+
+			/*
+			 * Cadence xHCI controllers store some endpoint state
+			 * information within Rsvd0 fields of Stream Endpoint
+			 * context. This field is not cleared during Set TR
+			 * Dequeue Pointer command which causes XDMA to skip
+			 * over transfer ring and leads to data loss on stream
+			 * pipe.
+			 * To fix this issue driver must clear Rsvd0 field.
+			 */
+			if (xhci->quirks & XHCI_CDNS_SCTX_QUIRK) {
+				ctx->reserved[0] = 0;
+				ctx->reserved[1] = 0;
+			}
 		} else {
 			deq = le64_to_cpu(ep_ctx->deq) & ~EP_CTX_CYCLE_MASK;
 		}
@@ -1454,8 +1631,21 @@
 	ep->ep_state &= ~SET_DEQ_PENDING;
 	ep->queued_deq_seg = NULL;
 	ep->queued_deq_ptr = NULL;
-	/* Restart any rings with pending URBs */
-	ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
+
+	/* Check for deferred or newly cancelled TDs */
+	if (!list_empty(&ep->cancelled_td_list)) {
+		xhci_dbg(ep->xhci, "%s: Pending TDs to clear, continuing with invalidation\n",
+			 __func__);
+		xhci_invalidate_cancelled_tds(ep);
+		/* Try to restart the endpoint if all is done */
+		ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
+		/* Start giving back any TDs invalidated above */
+		xhci_giveback_invalidated_tds(ep);
+	} else {
+		/* Restart any rings with pending URBs */
+		xhci_dbg(ep->xhci, "%s: All TDs cleared, ring doorbell\n", __func__);
+		ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
+	}
 }
 
 static void xhci_handle_cmd_reset_ep(struct xhci_hcd *xhci, int slot_id,
@@ -1518,7 +1708,6 @@
 	if (xhci->quirks & XHCI_EP_LIMIT_QUIRK)
 		/* Delete default control endpoint resources */
 		xhci_free_device_endpoint_resources(xhci, virt_dev, true);
-	xhci_free_virt_device(xhci, slot_id);
 }
 
 static void xhci_handle_cmd_config_ep(struct xhci_hcd *xhci, int slot_id,
@@ -1717,6 +1906,14 @@
 
 	trace_xhci_handle_command(xhci->cmd_ring, &cmd_trb->generic);
 
+	cmd_comp_code = GET_COMP_CODE(le32_to_cpu(event->status));
+
+	/* If CMD ring stopped we own the trbs between enqueue and dequeue */
+	if (cmd_comp_code == COMP_COMMAND_RING_STOPPED) {
+		complete_all(&xhci->cmd_ring_stop_completion);
+		return;
+	}
+
 	cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
 			cmd_trb);
 	/*
@@ -1733,14 +1930,6 @@
 
 	cancel_delayed_work(&xhci->cmd_timer);
 
-	cmd_comp_code = GET_COMP_CODE(le32_to_cpu(event->status));
-
-	/* If CMD ring stopped we own the trbs between enqueue and dequeue */
-	if (cmd_comp_code == COMP_COMMAND_RING_STOPPED) {
-		complete_all(&xhci->cmd_ring_stop_completion);
-		return;
-	}
-
 	if (cmd->command_trb != xhci->cmd_ring->dequeue) {
 		xhci_err(xhci,
 			 "Command completion event does not match command\n");
@@ -1822,7 +2011,7 @@
 	if (!list_is_singular(&xhci->cmd_list)) {
 		xhci->current_cmd = list_first_entry(&cmd->cmd_list,
 						struct xhci_command, cmd_list);
-		xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT);
+		xhci_mod_cmd_timer(xhci);
 	} else if (xhci->current_cmd == cmd) {
 		xhci->current_cmd = NULL;
 	}
@@ -1891,7 +2080,8 @@
 }
 
 static void handle_port_status(struct xhci_hcd *xhci,
-		union xhci_trb *event)
+			       struct xhci_interrupter *ir,
+			       union xhci_trb *event)
 {
 	struct usb_hcd *hcd;
 	u32 port_id;
@@ -1914,7 +2104,7 @@
 	if ((port_id <= 0) || (port_id > max_ports)) {
 		xhci_warn(xhci, "Port change event with invalid port ID %d\n",
 			  port_id);
-		inc_deq(xhci, xhci->event_ring);
+		inc_deq(xhci, ir->event_ring);
 		return;
 	}
 
@@ -1981,7 +2171,7 @@
 			goto cleanup;
 		} else if (!test_bit(hcd_portnum, &bus_state->resuming_ports)) {
 			xhci_dbg(xhci, "resume HS port %d\n", port_id);
-			bus_state->resume_done[hcd_portnum] = jiffies +
+			port->resume_timestamp = jiffies +
 				msecs_to_jiffies(USB_RESUME_TIMEOUT);
 			set_bit(hcd_portnum, &bus_state->resuming_ports);
 			/* Do the rest in GetPortStatus after resume time delay.
@@ -1990,7 +2180,7 @@
 			 */
 			set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 			mod_timer(&hcd->rh_timer,
-				  bus_state->resume_done[hcd_portnum]);
+				  port->resume_timestamp);
 			usb_hcd_start_port_resume(&hcd->self, hcd_portnum);
 			bogus_port_status = true;
 		}
@@ -2002,7 +2192,7 @@
 	     (portsc & PORT_PLS_MASK) == XDEV_U1 ||
 	     (portsc & PORT_PLS_MASK) == XDEV_U2)) {
 		xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
-		complete(&bus_state->u3exit_done[hcd_portnum]);
+		complete(&port->u3exit_done);
 		/* We've just brought the device into U0/1/2 through either the
 		 * Resume state after a device remote wakeup, or through the
 		 * U3Exit state after a host-initiated resume.  If it's a device
@@ -2027,10 +2217,9 @@
 	 * RExit to a disconnect state).  If so, let the the driver know it's
 	 * out of the RExit state.
 	 */
-	if (!DEV_SUPERSPEED_ANY(portsc) && hcd->speed < HCD_USB3 &&
-			test_and_clear_bit(hcd_portnum,
-				&bus_state->rexit_ports)) {
-		complete(&bus_state->rexit_done[hcd_portnum]);
+	if (hcd->speed < HCD_USB3 && port->rexit_active) {
+		complete(&port->rexit_done);
+		port->rexit_active = false;
 		bogus_port_status = true;
 		goto cleanup;
 	}
@@ -2044,7 +2233,7 @@
 
 cleanup:
 	/* Update event ring dequeue pointer before dropping the lock */
-	inc_deq(xhci, xhci->event_ring);
+	inc_deq(xhci, ir->event_ring);
 
 	/* Don't make the USB core poll the roothub if we got a bad port status
 	 * change event.  Besides, at that point we can't tell which roothub
@@ -2198,6 +2387,7 @@
 		     u32 trb_comp_code)
 {
 	struct xhci_ep_ctx *ep_ctx;
+	int trbs_freed;
 
 	ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep->ep_index);
 
@@ -2269,9 +2459,15 @@
 	}
 
 	/* Update ring dequeue pointer */
+	trbs_freed = xhci_num_trbs_to(ep_ring->deq_seg, ep_ring->dequeue,
+				      td->last_trb_seg, td->last_trb,
+				      ep_ring->num_segs);
+	if (trbs_freed < 0)
+		xhci_dbg(xhci, "Failed to count freed trbs at TD finish\n");
+	else
+		ep_ring->num_trbs_free += trbs_freed;
 	ep_ring->dequeue = td->last_trb;
 	ep_ring->deq_seg = td->last_trb_seg;
-	ep_ring->num_trbs_free += td->num_trbs - 1;
 	inc_deq(xhci, ep_ring);
 
 	return xhci_td_cleanup(xhci, td, ep_ring, td->status);
@@ -2416,6 +2612,9 @@
 	/* handle completion code */
 	switch (trb_comp_code) {
 	case COMP_SUCCESS:
+		/* Don't overwrite status if TD had an error, see xHCI 4.9.1 */
+		if (td->error_mid_td)
+			break;
 		if (remaining) {
 			frame->status = short_framestatus;
 			if (xhci->quirks & XHCI_TRUST_TX_LENGTH)
@@ -2431,9 +2630,13 @@
 	case COMP_BANDWIDTH_OVERRUN_ERROR:
 		frame->status = -ECOMM;
 		break;
-	case COMP_ISOCH_BUFFER_OVERRUN:
 	case COMP_BABBLE_DETECTED_ERROR:
+		sum_trbs_for_length = true;
+		fallthrough;
+	case COMP_ISOCH_BUFFER_OVERRUN:
 		frame->status = -EOVERFLOW;
+		if (ep_trb != td->last_trb)
+			td->error_mid_td = true;
 		break;
 	case COMP_INCOMPATIBLE_DEVICE_ERROR:
 	case COMP_STALL_ERROR:
@@ -2441,8 +2644,9 @@
 		break;
 	case COMP_USB_TRANSACTION_ERROR:
 		frame->status = -EPROTO;
+		sum_trbs_for_length = true;
 		if (ep_trb != td->last_trb)
-			return 0;
+			td->error_mid_td = true;
 		break;
 	case COMP_STOPPED:
 		sum_trbs_for_length = true;
@@ -2462,6 +2666,9 @@
 		break;
 	}
 
+	if (td->urb_length_set)
+		goto finish_td;
+
 	if (sum_trbs_for_length)
 		frame->actual_length = sum_trb_lengths(xhci, ep->ring, ep_trb) +
 			ep_trb_len - remaining;
@@ -2470,6 +2677,14 @@
 
 	td->urb->actual_length += frame->actual_length;
 
+finish_td:
+	/* Don't give back TD yet if we encountered an error mid TD */
+	if (td->error_mid_td && ep_trb != td->last_trb) {
+		xhci_dbg(xhci, "Error mid isoc TD, wait for final completion event\n");
+		td->urb_length_set = true;
+		return 0;
+	}
+
 	return finish_td(xhci, ep, ep_ring, td, trb_comp_code);
 }
 
@@ -2518,7 +2733,7 @@
 
 	switch (trb_comp_code) {
 	case COMP_SUCCESS:
-		ep_ring->err_count = 0;
+		ep->err_count = 0;
 		/* handle success with untransferred data as short packet */
 		if (ep_trb != td->last_trb || remaining) {
 			xhci_warn(xhci, "WARN Successful completion on short TX\n");
@@ -2539,12 +2754,11 @@
 		goto finish_td;
 	case COMP_STOPPED_LENGTH_INVALID:
 		/* stopped on ep trb with invalid length, exclude it */
-		ep_trb_len	= 0;
-		remaining	= 0;
-		break;
+		td->urb->actual_length = sum_trb_lengths(xhci, ep_ring, ep_trb);
+		goto finish_td;
 	case COMP_USB_TRANSACTION_ERROR:
 		if (xhci->quirks & XHCI_NO_SOFT_RETRY ||
-		    (ep_ring->err_count++ > MAX_SOFT_RETRY) ||
+		    (ep->err_count++ > MAX_SOFT_RETRY) ||
 		    le32_to_cpu(slot_ctx->tt_info) & TT_SLOT)
 			break;
 
@@ -2580,7 +2794,8 @@
  * At this point, the host controller is probably hosed and should be reset.
  */
 static int handle_tx_event(struct xhci_hcd *xhci,
-		struct xhci_transfer_event *event)
+			   struct xhci_interrupter *ir,
+			   struct xhci_transfer_event *event)
 {
 	struct xhci_virt_ep *ep;
 	struct xhci_ring *ep_ring;
@@ -2625,8 +2840,14 @@
 		case COMP_USB_TRANSACTION_ERROR:
 		case COMP_INVALID_STREAM_TYPE_ERROR:
 		case COMP_INVALID_STREAM_ID_ERROR:
-			xhci_handle_halted_endpoint(xhci, ep, 0, NULL,
-						    EP_SOFT_RESET);
+			xhci_dbg(xhci, "Stream transaction error ep %u no id\n",
+				 ep_index);
+			if (ep->err_count++ > MAX_SOFT_RETRY)
+				xhci_handle_halted_endpoint(xhci, ep, 0, NULL,
+							    EP_HARD_RESET);
+			else
+				xhci_handle_halted_endpoint(xhci, ep, 0, NULL,
+							    EP_SOFT_RESET);
 			goto cleanup;
 		case COMP_RING_UNDERRUN:
 		case COMP_RING_OVERRUN:
@@ -2645,6 +2866,10 @@
 			td_num++;
 	}
 
+	if ((xhci->quirks & XHCI_STREAM_QUIRK) &&
+				(ep->ep_state & EP_HAS_STREAMS))
+		del_timer(&ep_ring->stream_timer);
+
 	/* Look for common error cases */
 	switch (trb_comp_code) {
 	/* Skip codes that require special handling depending on
@@ -2848,17 +3073,51 @@
 		}
 
 		if (!ep_seg) {
-			if (!ep->skip ||
-			    !usb_endpoint_xfer_isoc(&td->urb->ep->desc)) {
-				/* Some host controllers give a spurious
-				 * successful event after a short transfer.
-				 * Ignore it.
-				 */
-				if ((xhci->quirks & XHCI_SPURIOUS_SUCCESS) &&
-						ep_ring->last_td_was_short) {
-					ep_ring->last_td_was_short = false;
-					goto cleanup;
+
+			if (ep->skip && usb_endpoint_xfer_isoc(&td->urb->ep->desc)) {
+				skip_isoc_td(xhci, td, ep, status);
+				goto cleanup;
+			}
+
+			/*
+			 * Some hosts give a spurious success event after a short
+			 * transfer. Ignore it.
+			 */
+			if ((xhci->quirks & XHCI_SPURIOUS_SUCCESS) &&
+			    ep_ring->last_td_was_short) {
+				ep_ring->last_td_was_short = false;
+				goto cleanup;
+			}
+
+			/*
+			 * xhci 4.10.2 states isoc endpoints should continue
+			 * processing the next TD if there was an error mid TD.
+			 * So host like NEC don't generate an event for the last
+			 * isoc TRB even if the IOC flag is set.
+			 * xhci 4.9.1 states that if there are errors in mult-TRB
+			 * TDs xHC should generate an error for that TRB, and if xHC
+			 * proceeds to the next TD it should genete an event for
+			 * any TRB with IOC flag on the way. Other host follow this.
+			 * So this event might be for the next TD.
+			 */
+			if (td->error_mid_td &&
+			    !list_is_last(&td->td_list, &ep_ring->td_list)) {
+				struct xhci_td *td_next = list_next_entry(td, td_list);
+
+				ep_seg = trb_in_td(xhci, td_next->start_seg, td_next->first_trb,
+						   td_next->last_trb, ep_trb_dma, false);
+				if (ep_seg) {
+					/* give back previous TD, start handling new */
+					xhci_dbg(xhci, "Missing TD completion event after mid TD error\n");
+					ep_ring->dequeue = td->last_trb;
+					ep_ring->deq_seg = td->last_trb_seg;
+					inc_deq(xhci, ep_ring);
+					xhci_td_cleanup(xhci, td, ep_ring, td->status);
+					td = td_next;
 				}
+			}
+
+			if (!ep_seg) {
 				/* HC is busted, give up! */
 				xhci_err(xhci,
 					"ERROR Transfer event TRB DMA ptr not "
@@ -2870,9 +3129,6 @@
 					  ep_trb_dma, true);
 				return -ESHUTDOWN;
 			}
-
-			skip_isoc_td(xhci, td, ep, status);
-			goto cleanup;
 		}
 		if (trb_comp_code == COMP_SHORT_PACKET)
 			ep_ring->last_td_was_short = true;
@@ -2929,7 +3185,7 @@
 		 * processing missed tds.
 		 */
 		if (!handling_skipped_tds)
-			inc_deq(xhci, xhci->event_ring);
+			inc_deq(xhci, ir->event_ring);
 
 	/*
 	 * If ep->skip is set, it means there are missed tds on the
@@ -2944,8 +3200,8 @@
 err_out:
 	xhci_err(xhci, "@%016llx %08x %08x %08x %08x\n",
 		 (unsigned long long) xhci_trb_virt_to_dma(
-			 xhci->event_ring->deq_seg,
-			 xhci->event_ring->dequeue),
+			 ir->event_ring->deq_seg,
+			 ir->event_ring->dequeue),
 		 lower_32_bits(le64_to_cpu(event->buffer)),
 		 upper_32_bits(le64_to_cpu(event->buffer)),
 		 le32_to_cpu(event->transfer_len),
@@ -2959,7 +3215,7 @@
  * Returns >0 for "possibly more events to process" (caller should call again),
  * otherwise 0 if done.  In future, <0 returns should indicate error code.
  */
-static int xhci_handle_event(struct xhci_hcd *xhci)
+static int xhci_handle_event(struct xhci_hcd *xhci, struct xhci_interrupter *ir)
 {
 	union xhci_trb *event;
 	int update_ptrs = 1;
@@ -2967,18 +3223,18 @@
 	int ret;
 
 	/* Event ring hasn't been allocated yet. */
-	if (!xhci->event_ring || !xhci->event_ring->dequeue) {
-		xhci_err(xhci, "ERROR event ring not ready\n");
+	if (!ir || !ir->event_ring || !ir->event_ring->dequeue) {
+		xhci_err(xhci, "ERROR interrupter not ready\n");
 		return -ENOMEM;
 	}
 
-	event = xhci->event_ring->dequeue;
+	event = ir->event_ring->dequeue;
 	/* Does the HC or OS own the TRB? */
 	if ((le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE) !=
-	    xhci->event_ring->cycle_state)
+	    ir->event_ring->cycle_state)
 		return 0;
 
-	trace_xhci_handle_event(xhci->event_ring, &event->generic);
+	trace_xhci_handle_event(ir->event_ring, &event->generic);
 
 	/*
 	 * Barrier between reading the TRB_CYCLE (valid) flag above and any
@@ -2993,11 +3249,11 @@
 		handle_cmd_completion(xhci, &event->event_cmd);
 		break;
 	case TRB_PORT_STATUS:
-		handle_port_status(xhci, event);
+		handle_port_status(xhci, ir, event);
 		update_ptrs = 0;
 		break;
 	case TRB_TRANSFER:
-		ret = handle_tx_event(xhci, &event->trans_event);
+		ret = handle_tx_event(xhci, ir, &event->trans_event);
 		if (ret >= 0)
 			update_ptrs = 0;
 		break;
@@ -3021,7 +3277,7 @@
 
 	if (update_ptrs)
 		/* Update SW event ring dequeue pointer */
-		inc_deq(xhci, xhci->event_ring);
+		inc_deq(xhci, ir->event_ring);
 
 	/* Are there more items on the event ring?  Caller will call us again to
 	 * check.
@@ -3035,16 +3291,17 @@
  * - To avoid "Event Ring Full Error" condition
  */
 static void xhci_update_erst_dequeue(struct xhci_hcd *xhci,
-		union xhci_trb *event_ring_deq)
+				     struct xhci_interrupter *ir,
+				     union xhci_trb *event_ring_deq)
 {
 	u64 temp_64;
 	dma_addr_t deq;
 
-	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	temp_64 = xhci_read_64(xhci, &ir->ir_set->erst_dequeue);
 	/* If necessary, update the HW's version of the event ring deq ptr. */
-	if (event_ring_deq != xhci->event_ring->dequeue) {
-		deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg,
-				xhci->event_ring->dequeue);
+	if (event_ring_deq != ir->event_ring->dequeue) {
+		deq = xhci_trb_virt_to_dma(ir->event_ring->deq_seg,
+				ir->event_ring->dequeue);
 		if (deq == 0)
 			xhci_warn(xhci, "WARN something wrong with SW event ring dequeue ptr\n");
 		/*
@@ -3062,7 +3319,7 @@
 
 	/* Clear the event handler busy flag (RW1C) */
 	temp_64 |= ERST_EHB;
-	xhci_write_64(xhci, temp_64, &xhci->ir_set->erst_dequeue);
+	xhci_write_64(xhci, temp_64, &ir->ir_set->erst_dequeue);
 }
 
 /*
@@ -3074,6 +3331,7 @@
 {
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	union xhci_trb *event_ring_deq;
+	struct xhci_interrupter *ir;
 	irqreturn_t ret = IRQ_NONE;
 	u64 temp_64;
 	u32 status;
@@ -3106,11 +3364,13 @@
 	status |= STS_EINT;
 	writel(status, &xhci->op_regs->status);
 
+	/* This is the handler of the primary interrupter */
+	ir = xhci->interrupter;
 	if (!hcd->msi_enabled) {
 		u32 irq_pending;
-		irq_pending = readl(&xhci->ir_set->irq_pending);
+		irq_pending = readl(&ir->ir_set->irq_pending);
 		irq_pending |= IMAN_IP;
-		writel(irq_pending, &xhci->ir_set->irq_pending);
+		writel(irq_pending, &ir->ir_set->irq_pending);
 	}
 
 	if (xhci->xhc_state & XHCI_STATE_DYING ||
@@ -3120,21 +3380,22 @@
 		/* Clear the event handler busy flag (RW1C);
 		 * the event ring should be empty.
 		 */
-		temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+		temp_64 = xhci_read_64(xhci, &ir->ir_set->erst_dequeue);
 		xhci_write_64(xhci, temp_64 | ERST_EHB,
-				&xhci->ir_set->erst_dequeue);
+				&ir->ir_set->erst_dequeue);
 		ret = IRQ_HANDLED;
 		goto out;
 	}
 
-	event_ring_deq = xhci->event_ring->dequeue;
+	event_ring_deq = ir->event_ring->dequeue;
 	/* FIXME this should be a delayed service routine
 	 * that clears the EHB.
 	 */
-	while (xhci_handle_event(xhci) > 0) {
+	while (xhci_handle_event(xhci, ir) > 0) {
 		if (event_loop++ < TRBS_PER_SEGMENT / 2)
 			continue;
-		xhci_update_erst_dequeue(xhci, event_ring_deq);
+		xhci_update_erst_dequeue(xhci, ir, event_ring_deq);
+		event_ring_deq = ir->event_ring->dequeue;
 
 		/* ring is half-full, force isoc trbs to interrupt more often */
 		if (xhci->isoc_bei_interval > AVOID_BEI_INTERVAL_MIN)
@@ -3143,7 +3404,7 @@
 		event_loop = 0;
 	}
 
-	xhci_update_erst_dequeue(xhci, event_ring_deq);
+	xhci_update_erst_dequeue(xhci, ir, event_ring_deq);
 	ret = IRQ_HANDLED;
 
 out:
@@ -3501,7 +3762,7 @@
 static int xhci_align_td(struct xhci_hcd *xhci, struct urb *urb, u32 enqd_len,
 			 u32 *trb_buff_len, struct xhci_segment *seg)
 {
-	struct device *dev = xhci_to_hcd(xhci)->self.controller;
+	struct device *dev = xhci_to_hcd(xhci)->self.sysdev;
 	unsigned int unalign;
 	unsigned int max_pkt;
 	u32 new_buff_len;
@@ -3723,6 +3984,15 @@
 	}
 
 	check_trb_math(urb, enqd_len);
+
+	if ((xhci->quirks & XHCI_STREAM_QUIRK) && (urb->stream_id > 0) &&
+				(usb_endpoint_dir_in(&urb->ep->desc) == 1)) {
+		/* Start the stream timer so that xhci_stream_timeout() can be
+		 * triggered if xhci is stuck while processing BULK IN streams.
+		 */
+		ring->stream_timeout_handler = false;
+		mod_timer(&ring->stream_timer, jiffies + 5 * HZ);
+	}
 	giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
 			start_cycle, start_trb);
 	return 0;
@@ -4335,7 +4605,7 @@
 	/* if there are no other commands queued we start the timeout timer */
 	if (list_empty(&xhci->cmd_list)) {
 		xhci->current_cmd = cmd;
-		xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT);
+		xhci_mod_cmd_timer(xhci);
 	}
 
 	list_add_tail(&cmd->cmd_list, &xhci->cmd_list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci-tegra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci-tegra.c
@@ -1034,13 +1034,13 @@
 	int rc;
 
 	if (tegra->use_genpd) {
-		rc = pm_runtime_get_sync(tegra->genpd_dev_ss);
+		rc = pm_runtime_resume_and_get(tegra->genpd_dev_ss);
 		if (rc < 0) {
 			dev_err(dev, "failed to enable XUSB SS partition\n");
 			return rc;
 		}
 
-		rc = pm_runtime_get_sync(tegra->genpd_dev_host);
+		rc = pm_runtime_resume_and_get(tegra->genpd_dev_host);
 		if (rc < 0) {
 			dev_err(dev, "failed to enable XUSB Host partition\n");
 			pm_runtime_put_sync(tegra->genpd_dev_ss);
@@ -1225,6 +1225,9 @@
 
 	mutex_unlock(&tegra->lock);
 
+	tegra->otg_usb3_port = tegra_xusb_padctl_get_usb3_companion(tegra->padctl,
+								    tegra->otg_usb2_port);
+
 	if (tegra->host_mode) {
 		/* switch to host mode */
 		if (tegra->otg_usb3_port >= 0) {
@@ -1339,9 +1342,6 @@
 	}
 
 	tegra->otg_usb2_port = tegra_xusb_get_usb2_port(tegra, usbphy);
-	tegra->otg_usb3_port = tegra_xusb_padctl_get_usb3_companion(
-							tegra->padctl,
-							tegra->otg_usb2_port);
 
 	tegra->host_mode = (usbphy->last_event == USB_EVENT_ID) ? true : false;
 
@@ -1400,6 +1400,7 @@
 
 static int tegra_xusb_probe(struct platform_device *pdev)
 {
+	struct of_phandle_args args;
 	struct tegra_xusb *tegra;
 	struct device_node *np;
 	struct resource *regs;
@@ -1454,10 +1455,17 @@
 		goto put_padctl;
 	}
 
-	tegra->padctl_irq = of_irq_get(np, 0);
-	if (tegra->padctl_irq <= 0) {
-		err = (tegra->padctl_irq == 0) ? -ENODEV : tegra->padctl_irq;
-		goto put_padctl;
+	/* Older device-trees don't have padctrl interrupt */
+	err = of_irq_parse_one(np, 0, &args);
+	if (!err) {
+		tegra->padctl_irq = of_irq_get(np, 0);
+		if (tegra->padctl_irq <= 0) {
+			err = (tegra->padctl_irq == 0) ? -ENODEV : tegra->padctl_irq;
+			goto put_padctl;
+		}
+	} else {
+		dev_dbg(&pdev->dev,
+			"%pOF is missing an interrupt, disabling PM support\n", np);
 	}
 
 	tegra->host_clk = devm_clk_get(&pdev->dev, "xusb_host");
@@ -1696,11 +1704,15 @@
 		goto remove_usb3;
 	}
 
-	err = devm_request_threaded_irq(&pdev->dev, tegra->padctl_irq, NULL, tegra_xusb_padctl_irq,
-					IRQF_ONESHOT, dev_name(&pdev->dev), tegra);
-	if (err < 0) {
-		dev_err(&pdev->dev, "failed to request padctl IRQ: %d\n", err);
-		goto remove_usb3;
+	if (tegra->padctl_irq) {
+		err = devm_request_threaded_irq(&pdev->dev, tegra->padctl_irq,
+						NULL, tegra_xusb_padctl_irq,
+						IRQF_ONESHOT, dev_name(&pdev->dev),
+						tegra);
+		if (err < 0) {
+			dev_err(&pdev->dev, "failed to request padctl IRQ: %d\n", err);
+			goto remove_usb3;
+		}
 	}
 
 	err = tegra_xusb_enable_firmware_messages(tegra);
@@ -1718,13 +1730,16 @@
 	/* Enable wake for both USB 2.0 and USB 3.0 roothubs */
 	device_init_wakeup(&tegra->hcd->self.root_hub->dev, true);
 	device_init_wakeup(&xhci->shared_hcd->self.root_hub->dev, true);
-	device_init_wakeup(tegra->dev, true);
 
 	pm_runtime_use_autosuspend(tegra->dev);
 	pm_runtime_set_autosuspend_delay(tegra->dev, 2000);
 	pm_runtime_mark_last_busy(tegra->dev);
 	pm_runtime_set_active(tegra->dev);
-	pm_runtime_enable(tegra->dev);
+
+	if (tegra->padctl_irq) {
+		device_init_wakeup(tegra->dev, true);
+		pm_runtime_enable(tegra->dev);
+	}
 
 	return 0;
 
@@ -1772,7 +1787,9 @@
 	dma_free_coherent(&pdev->dev, tegra->fw.size, tegra->fw.virt,
 			  tegra->fw.phys);
 
-	pm_runtime_disable(&pdev->dev);
+	if (tegra->padctl_irq)
+		pm_runtime_disable(&pdev->dev);
+
 	pm_runtime_put(&pdev->dev);
 
 	tegra_xusb_powergate_partitions(tegra);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci.c
@@ -8,7 +8,9 @@
  * Some code borrowed from the Linux EHCI driver.
  */
 
+#include <linux/jiffies.h>
 #include <linux/pci.h>
+#include <linux/iommu.h>
 #include <linux/iopoll.h>
 #include <linux/irq.h>
 #include <linux/log2.h>
@@ -65,7 +67,7 @@
  * handshake done).  There are two failure modes:  "usec" have passed (major
  * hardware flakeout), or the register reads as all-ones (hardware removed).
  */
-int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, int usec)
+int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, u64 timeout_us)
 {
 	u32	result;
 	int	ret;
@@ -73,7 +75,7 @@
 	ret = readl_poll_timeout_atomic(ptr, result,
 					(result & mask) == done ||
 					result == U32_MAX,
-					1, usec);
+					1, timeout_us);
 	if (result == U32_MAX)		/* card removed */
 		return -ENODEV;
 
@@ -148,9 +150,11 @@
 		xhci_err(xhci, "Host took too long to start, "
 				"waited %u microseconds.\n",
 				XHCI_MAX_HALT_USEC);
-	if (!ret)
+	if (!ret) {
 		/* clear state flags. Including dying, halted or removing */
 		xhci->xhc_state = 0;
+		xhci->run_graceperiod = jiffies + msecs_to_jiffies(500);
+	}
 
 	return ret;
 }
@@ -162,7 +166,7 @@
  * Transactions will be terminated immediately, and operational registers
  * will be set to their defaults.
  */
-int xhci_reset(struct xhci_hcd *xhci)
+int xhci_reset(struct xhci_hcd *xhci, u64 timeout_us)
 {
 	u32 command;
 	u32 state;
@@ -182,7 +186,11 @@
 
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Reset the HC");
 	command = readl(&xhci->op_regs->command);
+#ifdef CONFIG_USB_DWC3_OTG
+	command |= CMD_LRESET;
+#else
 	command |= CMD_RESET;
+#endif
 	writel(command, &xhci->op_regs->command);
 
 	/* Existing Intel xHCI controllers require a delay of 1 mS,
@@ -196,7 +204,12 @@
 		udelay(1000);
 
 	ret = xhci_handshake(&xhci->op_regs->command,
-			CMD_RESET, 0, 10 * 1000 * 1000);
+#ifdef CONFIG_USB_DWC3_OTG
+			CMD_LRESET,
+#else
+			CMD_RESET,
+#endif
+			0, timeout_us);
 	if (ret)
 		return ret;
 
@@ -209,8 +222,7 @@
 	 * xHCI cannot write to any doorbells or operational registers other
 	 * than status until the "Controller Not Ready" flag is cleared.
 	 */
-	ret = xhci_handshake(&xhci->op_regs->status,
-			STS_CNR, 0, 10 * 1000 * 1000);
+	ret = xhci_handshake(&xhci->op_regs->status, STS_CNR, 0, timeout_us);
 
 	xhci->usb2_rhub.bus_state.port_c_suspend = 0;
 	xhci->usb2_rhub.bus_state.suspended_ports = 0;
@@ -225,6 +237,7 @@
 static void xhci_zero_64b_regs(struct xhci_hcd *xhci)
 {
 	struct device *dev = xhci_to_hcd(xhci)->self.sysdev;
+	struct iommu_domain *domain;
 	int err, i;
 	u64 val;
 	u32 intrs;
@@ -243,7 +256,9 @@
 	 * an iommu. Doing anything when there is no iommu is definitely
 	 * unsafe...
 	 */
-	if (!(xhci->quirks & XHCI_ZERO_64B_REGS) || !device_iommu_mapped(dev))
+	domain = iommu_get_domain_for_dev(dev);
+	if (!(xhci->quirks & XHCI_ZERO_64B_REGS) || !domain ||
+	    domain->type == IOMMU_DOMAIN_IDENTITY)
 		return;
 
 	xhci_info(xhci, "Zeroing 64bit base registers, expecting fault\n");
@@ -607,8 +622,28 @@
 
 static int xhci_run_finished(struct xhci_hcd *xhci)
 {
+	struct xhci_interrupter *ir = xhci->interrupter;
+	unsigned long	flags;
+	u32		temp;
+
+	/*
+	 * Enable interrupts before starting the host (xhci 4.2 and 5.5.2).
+	 * Protect the short window before host is running with a lock
+	 */
+	spin_lock_irqsave(&xhci->lock, flags);
+
+	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable interrupts");
+	temp = readl(&xhci->op_regs->command);
+	temp |= (CMD_EIE);
+	writel(temp, &xhci->op_regs->command);
+
+	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable primary interrupter");
+	temp = readl(&ir->ir_set->irq_pending);
+	writel(ER_IRQ_ENABLE(temp), &ir->ir_set->irq_pending);
+
 	if (xhci_start(xhci)) {
 		xhci_halt(xhci);
+		spin_unlock_irqrestore(&xhci->lock, flags);
 		return -ENODEV;
 	}
 	xhci->shared_hcd->state = HC_STATE_RUNNING;
@@ -619,6 +654,9 @@
 
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
 			"Finished xhci_run for USB3 roothub");
+
+	spin_unlock_irqrestore(&xhci->lock, flags);
+
 	return 0;
 }
 
@@ -640,7 +678,7 @@
 	u64 temp_64;
 	int ret;
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
-
+	struct xhci_interrupter *ir = xhci->interrupter;
 	/* Start the xHCI host controller running only after the USB 2.0 roothub
 	 * is setup.
 	 */
@@ -655,30 +693,17 @@
 	if (ret)
 		return ret;
 
-	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	temp_64 = xhci_read_64(xhci, &ir->ir_set->erst_dequeue);
 	temp_64 &= ~ERST_PTR_MASK;
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
 			"ERST deq = 64'h%0lx", (long unsigned int) temp_64);
 
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
 			"// Set the interrupt modulation register");
-	temp = readl(&xhci->ir_set->irq_control);
+	temp = readl(&ir->ir_set->irq_control);
 	temp &= ~ER_IRQ_INTERVAL_MASK;
 	temp |= (xhci->imod_interval / 250) & ER_IRQ_INTERVAL_MASK;
-	writel(temp, &xhci->ir_set->irq_control);
-
-	/* Set the HCD state before we enable the irqs */
-	temp = readl(&xhci->op_regs->command);
-	temp |= (CMD_EIE);
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
-			"// Enable interrupts, cmd = 0x%x.", temp);
-	writel(temp, &xhci->op_regs->command);
-
-	temp = readl(&xhci->ir_set->irq_pending);
-	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
-			"// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
-			xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
-	writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
+	writel(temp, &ir->ir_set->irq_control);
 
 	if (xhci->quirks & XHCI_NEC_HOST) {
 		struct xhci_command *command;
@@ -692,11 +717,12 @@
 		if (ret)
 			xhci_free_command(xhci, command);
 	}
-	set_bit(HCD_FLAG_DEFER_RH_REGISTER, &hcd->flags);
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
 			"Finished xhci_run for USB2 roothub");
 
-	xhci_dbc_init(xhci);
+	set_bit(HCD_FLAG_DEFER_RH_REGISTER, &hcd->flags);
+
+	xhci_create_dbc_dev(xhci);
 
 	xhci_debugfs_init(xhci);
 
@@ -726,13 +752,13 @@
 		return;
 	}
 
-	xhci_dbc_exit(xhci);
+	xhci_remove_dbc_dev(xhci);
 
 	spin_lock_irq(&xhci->lock);
 	xhci->xhc_state |= XHCI_STATE_HALTED;
 	xhci->cmd_ring_state = CMD_RING_STATE_STOPPED;
 	xhci_halt(xhci);
-	xhci_reset(xhci);
+	xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
 	spin_unlock_irq(&xhci->lock);
 
 	xhci_cleanup_msix(xhci);
@@ -753,8 +779,8 @@
 			"// Disabling event ring interrupts");
 	temp = readl(&xhci->op_regs->status);
 	writel((temp & ~0x1fff) | STS_EINT, &xhci->op_regs->status);
-	temp = readl(&xhci->ir_set->irq_pending);
-	writel(ER_IRQ_DISABLE(temp), &xhci->ir_set->irq_pending);
+	temp = readl(&xhci->interrupter->ir_set->irq_pending);
+	writel(ER_IRQ_DISABLE(temp), &xhci->interrupter->ir_set->irq_pending);
 
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init, "cleaning up memory");
 	xhci_mem_cleanup(xhci);
@@ -781,11 +807,28 @@
 	if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
 		usb_disable_xhci_ports(to_pci_dev(hcd->self.sysdev));
 
+	/* Don't poll the roothubs after shutdown. */
+	xhci_dbg(xhci, "%s: stopping usb%d port polling.\n",
+			__func__, hcd->self.busnum);
+	clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+	del_timer_sync(&hcd->rh_timer);
+
+	if (xhci->shared_hcd) {
+		clear_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags);
+		del_timer_sync(&xhci->shared_hcd->rh_timer);
+	}
+
 	spin_lock_irq(&xhci->lock);
 	xhci_halt(xhci);
-	/* Workaround for spurious wakeups at shutdown with HSW */
-	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
-		xhci_reset(xhci);
+
+	/*
+	 * Workaround for spurious wakeps at shutdown with HSW, and for boot
+	 * firmware delay in ADL-P PCH if port are left in U3 at shutdown
+	 */
+	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP ||
+	    xhci->quirks & XHCI_RESET_TO_DEFAULT)
+		xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
+
 	spin_unlock_irq(&xhci->lock);
 
 	xhci_cleanup_msix(xhci);
@@ -799,28 +842,36 @@
 #ifdef CONFIG_PM
 static void xhci_save_registers(struct xhci_hcd *xhci)
 {
+	struct xhci_interrupter *ir = xhci->interrupter;
+
 	xhci->s3.command = readl(&xhci->op_regs->command);
 	xhci->s3.dev_nt = readl(&xhci->op_regs->dev_notification);
 	xhci->s3.dcbaa_ptr = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
 	xhci->s3.config_reg = readl(&xhci->op_regs->config_reg);
-	xhci->s3.erst_size = readl(&xhci->ir_set->erst_size);
-	xhci->s3.erst_base = xhci_read_64(xhci, &xhci->ir_set->erst_base);
-	xhci->s3.erst_dequeue = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
-	xhci->s3.irq_pending = readl(&xhci->ir_set->irq_pending);
-	xhci->s3.irq_control = readl(&xhci->ir_set->irq_control);
+
+	if (!ir)
+		return;
+
+	ir->s3_erst_size = readl(&ir->ir_set->erst_size);
+	ir->s3_erst_base = xhci_read_64(xhci, &ir->ir_set->erst_base);
+	ir->s3_erst_dequeue = xhci_read_64(xhci, &ir->ir_set->erst_dequeue);
+	ir->s3_irq_pending = readl(&ir->ir_set->irq_pending);
+	ir->s3_irq_control = readl(&ir->ir_set->irq_control);
 }
 
 static void xhci_restore_registers(struct xhci_hcd *xhci)
 {
+	struct xhci_interrupter *ir = xhci->interrupter;
+
 	writel(xhci->s3.command, &xhci->op_regs->command);
 	writel(xhci->s3.dev_nt, &xhci->op_regs->dev_notification);
 	xhci_write_64(xhci, xhci->s3.dcbaa_ptr, &xhci->op_regs->dcbaa_ptr);
 	writel(xhci->s3.config_reg, &xhci->op_regs->config_reg);
-	writel(xhci->s3.erst_size, &xhci->ir_set->erst_size);
-	xhci_write_64(xhci, xhci->s3.erst_base, &xhci->ir_set->erst_base);
-	xhci_write_64(xhci, xhci->s3.erst_dequeue, &xhci->ir_set->erst_dequeue);
-	writel(xhci->s3.irq_pending, &xhci->ir_set->irq_pending);
-	writel(xhci->s3.irq_control, &xhci->ir_set->irq_control);
+	writel(ir->s3_erst_size, &ir->ir_set->erst_size);
+	xhci_write_64(xhci, ir->s3_erst_base, &ir->ir_set->erst_base);
+	xhci_write_64(xhci, ir->s3_erst_dequeue, &ir->ir_set->erst_dequeue);
+	writel(ir->s3_irq_pending, &ir->ir_set->irq_pending);
+	writel(ir->s3_irq_control, &ir->ir_set->irq_control);
 }
 
 static void xhci_set_cmd_ring_deq(struct xhci_hcd *xhci)
@@ -1092,6 +1143,7 @@
 	int			retval = 0;
 	bool			comp_timer_running = false;
 	bool			pending_portevent = false;
+	bool			reinit_xhc = false;
 
 	if (!hcd->state)
 		return 0;
@@ -1108,10 +1160,11 @@
 	set_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
 
 	spin_lock_irq(&xhci->lock);
-	if ((xhci->quirks & XHCI_RESET_ON_RESUME) || xhci->broken_suspend)
-		hibernated = true;
 
-	if (!hibernated) {
+	if (hibernated || xhci->quirks & XHCI_RESET_ON_RESUME || xhci->broken_suspend)
+		reinit_xhc = true;
+
+	if (!reinit_xhc) {
 		/*
 		 * Some controllers might lose power during suspend, so wait
 		 * for controller not ready bit to clear, just as in xHC init.
@@ -1144,12 +1197,18 @@
 			spin_unlock_irq(&xhci->lock);
 			return -ETIMEDOUT;
 		}
-		temp = readl(&xhci->op_regs->status);
 	}
 
-	/* If restore operation fails, re-initialize the HC during resume */
-	if ((temp & STS_SRE) || hibernated) {
+	temp = readl(&xhci->op_regs->status);
+
+	/* re-initialize the HC on Restore Error, or Host Controller Error */
+	if (temp & (STS_SRE | STS_HCE)) {
+		reinit_xhc = true;
+		if (!xhci->broken_suspend)
+			xhci_warn(xhci, "xHC error in resume, USBSTS 0x%x, Reinit\n", temp);
+	}
 
+	if (reinit_xhc) {
 		if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
 				!(xhci_all_ports_seen_u0(xhci))) {
 			del_timer_sync(&xhci->comp_mode_recovery_timer);
@@ -1164,7 +1223,7 @@
 		xhci_dbg(xhci, "Stop HCD\n");
 		xhci_halt(xhci);
 		xhci_zero_64b_regs(xhci);
-		retval = xhci_reset(xhci);
+		retval = xhci_reset(xhci, XHCI_RESET_LONG_USEC);
 		spin_unlock_irq(&xhci->lock);
 		if (retval)
 			return retval;
@@ -1173,8 +1232,8 @@
 		xhci_dbg(xhci, "// Disabling event ring interrupts\n");
 		temp = readl(&xhci->op_regs->status);
 		writel((temp & ~0x1fff) | STS_EINT, &xhci->op_regs->status);
-		temp = readl(&xhci->ir_set->irq_pending);
-		writel(ER_IRQ_DISABLE(temp), &xhci->ir_set->irq_pending);
+		temp = readl(&xhci->interrupter->ir_set->irq_pending);
+		writel(ER_IRQ_DISABLE(temp), &xhci->interrupter->ir_set->irq_pending);
 
 		xhci_dbg(xhci, "cleaning up memory\n");
 		xhci_mem_cleanup(xhci);
@@ -1285,6 +1344,8 @@
 
 	temp = kzalloc_node(buf_len, GFP_ATOMIC,
 			    dev_to_node(hcd->self.sysdev));
+	if (!temp)
+		return -ENOMEM;
 
 	if (usb_urb_dir_out(urb))
 		sg_pcopy_to_buffer(urb->sg, urb->num_sgs,
@@ -1605,9 +1666,12 @@
 	struct urb_priv	*urb_priv;
 	int num_tds;
 
-	if (!urb || xhci_check_args(hcd, urb->dev, urb->ep,
-					true, true, __func__) <= 0)
+	if (!urb)
 		return -EINVAL;
+	ret = xhci_check_args(hcd, urb->dev, urb->ep,
+					true, true, __func__);
+	if (ret <= 0)
+		return ret ? ret : -EINVAL;
 
 	slot_id = urb->dev->slot_id;
 	ep_index = xhci_get_endpoint_index(&urb->ep->desc);
@@ -1808,8 +1872,21 @@
 		goto err_giveback;
 	}
 
+	ep_index = xhci_get_endpoint_index(&urb->ep->desc);
+	ep = &xhci->devs[urb->dev->slot_id]->eps[ep_index];
+	ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
+	if (!ep_ring) {
+		ret = -EINVAL;
+		goto done;
+	}
+
+	/* Delete the stream timer */
+	if ((xhci->quirks & XHCI_STREAM_QUIRK) && (urb->stream_id > 0))
+		del_timer(&ep_ring->stream_timer);
+
 	i = urb_priv->num_tds_done;
 	if (i < urb_priv->num_tds)
+
 		xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
 				"Cancel URB %p, dev %s, ep 0x%x, "
 				"starting at offset 0x%llx",
@@ -1829,15 +1906,27 @@
 		}
 	}
 
-	/* Queue a stop endpoint command, but only if this is
-	 * the first cancellation to be handled.
-	 */
-	if (!(ep->ep_state & EP_STOP_CMD_PENDING)) {
+	/* These completion handlers will sort out cancelled TDs for us */
+	if (ep->ep_state & (EP_STOP_CMD_PENDING | EP_HALTED | SET_DEQ_PENDING)) {
+		xhci_dbg(xhci, "Not queuing Stop Endpoint on slot %d ep %d in state 0x%x\n",
+				urb->dev->slot_id, ep_index, ep->ep_state);
+		goto done;
+	}
+
+	/* In this case no commands are pending but the endpoint is stopped */
+	if (ep->ep_state & EP_CLEARING_TT) {
+		/* and cancelled TDs can be given back right away */
+		xhci_dbg(xhci, "Invalidating TDs instantly on slot %d ep %d in state 0x%x\n",
+				urb->dev->slot_id, ep_index, ep->ep_state);
+		xhci_process_cancelled_tds(ep);
+	} else {
+		/* Otherwise, queue a new Stop Endpoint command */
 		command = xhci_alloc_command(xhci, false, GFP_ATOMIC);
 		if (!command) {
 			ret = -ENOMEM;
 			goto done;
 		}
+		ep->stop_time = jiffies;
 		ep->ep_state |= EP_STOP_CMD_PENDING;
 		ep->stop_cmd_timer.expires = jiffies +
 			XHCI_STOP_EP_CMD_TIMEOUT * HZ;
@@ -2910,7 +2999,7 @@
 				xhci->num_active_eps);
 		return -ENOMEM;
 	}
-	if ((xhci->quirks & XHCI_SW_BW_CHECKING) &&
+	if ((xhci->quirks & XHCI_SW_BW_CHECKING) && !ctx_change &&
 	    xhci_reserve_bandwidth(xhci, virt_dev, command->in_ctx)) {
 		if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK))
 			xhci_free_host_resources(xhci, ctrl_ctx);
@@ -3324,7 +3413,7 @@
 		return -EINVAL;
 	ret = xhci_check_args(xhci_to_hcd(xhci), udev, ep, 1, true, __func__);
 	if (ret <= 0)
-		return -EINVAL;
+		return ret ? ret : -EINVAL;
 	if (usb_ss_max_streams(&ep->ss_ep_comp) == 0) {
 		xhci_warn(xhci, "WARN: SuperSpeed Endpoint Companion"
 				" descriptor for ep 0x%x does not support streams\n",
@@ -3933,9 +4022,9 @@
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_virt_device *virt_dev;
 	struct xhci_slot_ctx *slot_ctx;
+	unsigned long flags;
 	int i, ret;
 
-#ifndef CONFIG_USB_DEFAULT_PERSIST
 	/*
 	 * We called pm_runtime_get_noresume when the device was attached.
 	 * Decrement the counter here to allow controller to runtime suspend
@@ -3943,7 +4032,6 @@
 	 */
 	if (xhci->quirks & XHCI_RESET_ON_RESUME)
 		pm_runtime_put_noidle(hcd->self.controller);
-#endif
 
 	ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
 	/* If the host is halted due to driver unload, we still need to free the
@@ -3962,9 +4050,12 @@
 		del_timer_sync(&virt_dev->eps[i].stop_cmd_timer);
 	}
 	virt_dev->udev = NULL;
-	ret = xhci_disable_slot(xhci, udev->slot_id);
-	if (ret)
-		xhci_free_virt_device(xhci, udev->slot_id);
+	xhci_disable_slot(xhci, udev->slot_id);
+
+	spin_lock_irqsave(&xhci->lock, flags);
+	xhci_free_virt_device(xhci, udev->slot_id);
+	spin_unlock_irqrestore(&xhci->lock, flags);
+
 }
 
 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id)
@@ -3974,7 +4065,7 @@
 	u32 state;
 	int ret = 0;
 
-	command = xhci_alloc_command(xhci, false, GFP_KERNEL);
+	command = xhci_alloc_command(xhci, true, GFP_KERNEL);
 	if (!command)
 		return -ENOMEM;
 
@@ -3999,6 +4090,15 @@
 	}
 	xhci_ring_cmd_db(xhci);
 	spin_unlock_irqrestore(&xhci->lock, flags);
+
+	wait_for_completion(command->completion);
+
+	if (command->status != COMP_SUCCESS)
+		xhci_warn(xhci, "Unsuccessful disable slot %u command, status %d\n",
+			  slot_id, command->status);
+
+	xhci_free_command(xhci, command);
+
 	return ret;
 }
 
@@ -4095,33 +4195,36 @@
 
 	xhci_debugfs_create_slot(xhci, slot_id);
 
-#ifndef CONFIG_USB_DEFAULT_PERSIST
 	/*
 	 * If resetting upon resume, we can't put the controller into runtime
 	 * suspend if there is a device attached.
 	 */
 	if (xhci->quirks & XHCI_RESET_ON_RESUME)
 		pm_runtime_get_noresume(hcd->self.controller);
-#endif
 
 	/* Is this a LS or FS device under a HS hub? */
 	/* Hub or peripherial? */
 	return 1;
 
 disable_slot:
-	ret = xhci_disable_slot(xhci, udev->slot_id);
-	if (ret)
-		xhci_free_virt_device(xhci, udev->slot_id);
+	xhci_disable_slot(xhci, udev->slot_id);
+	xhci_free_virt_device(xhci, udev->slot_id);
 
 	return 0;
 }
 
-/*
- * Issue an Address Device command and optionally send a corresponding
- * SetAddress request to the device.
+/**
+ * xhci_setup_device - issues an Address Device command to assign a unique
+ *			USB bus address.
+ * @hcd: USB host controller data structure.
+ * @udev: USB dev structure representing the connected device.
+ * @setup: Enum specifying setup mode: address only or with context.
+ * @timeout_ms: Max wait time (ms) for the command operation to complete.
+ *
+ * Return: 0 if successful; otherwise, negative error code.
  */
 static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev,
-			     enum xhci_setup_dev setup)
+			     enum xhci_setup_dev setup, unsigned int timeout_ms)
 {
 	const char *act = setup == SETUP_CONTEXT_ONLY ? "context" : "address";
 	unsigned long flags;
@@ -4178,6 +4281,7 @@
 	}
 
 	command->in_ctx = virt_dev->in_ctx;
+	command->timeout_ms = timeout_ms;
 
 	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	ctrl_ctx = xhci_get_input_control_ctx(virt_dev->in_ctx);
@@ -4241,8 +4345,11 @@
 
 		mutex_unlock(&xhci->mutex);
 		ret = xhci_disable_slot(xhci, udev->slot_id);
-		if (!ret)
-			xhci_alloc_dev(hcd, udev);
+		xhci_free_virt_device(xhci, udev->slot_id);
+		if (!ret) {
+			if (xhci_alloc_dev(hcd, udev) == 1)
+				xhci_setup_addressable_virt_dev(xhci, udev);
+		}
 		kfree(command->completion);
 		kfree(command);
 		return -EPROTO;
@@ -4303,14 +4410,16 @@
 	return ret;
 }
 
-static int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
+static int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev,
+			       unsigned int timeout_ms)
 {
-	return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ADDRESS);
+	return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ADDRESS, timeout_ms);
 }
 
 static int xhci_enable_device(struct usb_hcd *hcd, struct usb_device *udev)
 {
-	return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ONLY);
+	return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ONLY,
+				 XHCI_CMD_DEFAULT_TIMEOUT);
 }
 
 /*
@@ -5013,6 +5122,7 @@
 			struct usb_device *udev, enum usb3_link_state state)
 {
 	struct xhci_hcd	*xhci;
+	struct xhci_port *port;
 	u16 hub_encoded_timeout;
 	int mel;
 	int ret;
@@ -5026,6 +5136,13 @@
 			!xhci->devs[udev->slot_id])
 		return USB3_LPM_DISABLED;
 
+	/* If connected to root port then check port can handle lpm */
+	if (udev->parent && !udev->parent->parent) {
+		port = xhci->usb3_rhub.ports[udev->portnum - 1];
+		if (port->lpm_incapable)
+			return USB3_LPM_DISABLED;
+	}
+
 	hub_encoded_timeout = xhci_calculate_lpm_timeout(hcd, udev, state);
 	mel = calculate_max_exit_latency(udev, state, hub_encoded_timeout);
 	if (mel < 0) {
@@ -5085,7 +5202,7 @@
 /* Once a hub descriptor is fetched for a device, we need to update the xHC's
  * internal data structures for the device.
  */
-static int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
+int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
 			struct usb_tt *tt, gfp_t mem_flags)
 {
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
@@ -5185,6 +5302,7 @@
 	xhci_free_command(xhci, config_cmd);
 	return ret;
 }
+EXPORT_SYMBOL_GPL(xhci_update_hub_device);
 
 static int xhci_get_frame(struct usb_hcd *hcd)
 {
@@ -5285,6 +5403,11 @@
 	if (xhci->hci_version > 0x100)
 		xhci->hcc_params2 = readl(&xhci->cap_regs->hcc_params2);
 
+	/* xhci-plat or xhci-pci might have set max_interrupters already */
+	if ((!xhci->max_interrupters) ||
+	    xhci->max_interrupters > HCS_MAX_INTRS(xhci->hcs_params1))
+		xhci->max_interrupters = HCS_MAX_INTRS(xhci->hcs_params1);
+
 	xhci->quirks |= quirks;
 
 	get_quirks(dev, xhci);
@@ -5305,7 +5428,7 @@
 
 	xhci_dbg(xhci, "Resetting HCD\n");
 	/* Reset the internal HC memory state and registers. */
-	retval = xhci_reset(xhci);
+	retval = xhci_reset(xhci, XHCI_RESET_LONG_USEC);
 	if (retval)
 		return retval;
 	xhci_dbg(xhci, "Reset complete\n");
@@ -5462,6 +5585,8 @@
 			drv->check_bandwidth = over->check_bandwidth;
 		if (over->reset_bandwidth)
 			drv->reset_bandwidth = over->reset_bandwidth;
+		if (over->update_hub_device)
+			drv->update_hub_device = over->update_hub_device;
 	}
 }
 EXPORT_SYMBOL_GPL(xhci_init_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/host/xhci.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/host/xhci.h
@@ -17,11 +17,15 @@
 #include <linux/kernel.h>
 #include <linux/usb/hcd.h>
 #include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/io-64-nonatomic-hi-lo.h>
 
 /* Code sharing between pci-quirks and xhci hcd */
 #include	"xhci-ext-caps.h"
 #include "pci-quirks.h"
 
+#include "xhci-port.h"
+#include "xhci-caps.h"
+
 /* max buffer size for trace and debug messages */
 #define XHCI_MSG_MAX		500
 
@@ -62,90 +66,6 @@
 	/* Reserved up to (CAPLENGTH - 0x1C) */
 };
 
-/* hc_capbase bitmasks */
-/* bits 7:0 - how long is the Capabilities register */
-#define HC_LENGTH(p)		XHCI_HC_LENGTH(p)
-/* bits 31:16	*/
-#define HC_VERSION(p)		(((p) >> 16) & 0xffff)
-
-/* HCSPARAMS1 - hcs_params1 - bitmasks */
-/* bits 0:7, Max Device Slots */
-#define HCS_MAX_SLOTS(p)	(((p) >> 0) & 0xff)
-#define HCS_SLOTS_MASK		0xff
-/* bits 8:18, Max Interrupters */
-#define HCS_MAX_INTRS(p)	(((p) >> 8) & 0x7ff)
-/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
-#define HCS_MAX_PORTS(p)	(((p) >> 24) & 0x7f)
-
-/* HCSPARAMS2 - hcs_params2 - bitmasks */
-/* bits 0:3, frames or uframes that SW needs to queue transactions
- * ahead of the HW to meet periodic deadlines */
-#define HCS_IST(p)		(((p) >> 0) & 0xf)
-/* bits 4:7, max number of Event Ring segments */
-#define HCS_ERST_MAX(p)		(((p) >> 4) & 0xf)
-/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
-/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
-/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
-#define HCS_MAX_SCRATCHPAD(p)   ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
-
-/* HCSPARAMS3 - hcs_params3 - bitmasks */
-/* bits 0:7, Max U1 to U0 latency for the roothub ports */
-#define HCS_U1_LATENCY(p)	(((p) >> 0) & 0xff)
-/* bits 16:31, Max U2 to U0 latency for the roothub ports */
-#define HCS_U2_LATENCY(p)	(((p) >> 16) & 0xffff)
-
-/* HCCPARAMS - hcc_params - bitmasks */
-/* true: HC can use 64-bit address pointers */
-#define HCC_64BIT_ADDR(p)	((p) & (1 << 0))
-/* true: HC can do bandwidth negotiation */
-#define HCC_BANDWIDTH_NEG(p)	((p) & (1 << 1))
-/* true: HC uses 64-byte Device Context structures
- * FIXME 64-byte context structures aren't supported yet.
- */
-#define HCC_64BYTE_CONTEXT(p)	((p) & (1 << 2))
-/* true: HC has port power switches */
-#define HCC_PPC(p)		((p) & (1 << 3))
-/* true: HC has port indicators */
-#define HCS_INDICATOR(p)	((p) & (1 << 4))
-/* true: HC has Light HC Reset Capability */
-#define HCC_LIGHT_RESET(p)	((p) & (1 << 5))
-/* true: HC supports latency tolerance messaging */
-#define HCC_LTC(p)		((p) & (1 << 6))
-/* true: no secondary Stream ID Support */
-#define HCC_NSS(p)		((p) & (1 << 7))
-/* true: HC supports Stopped - Short Packet */
-#define HCC_SPC(p)		((p) & (1 << 9))
-/* true: HC has Contiguous Frame ID Capability */
-#define HCC_CFC(p)		((p) & (1 << 11))
-/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
-#define HCC_MAX_PSA(p)		(1 << ((((p) >> 12) & 0xf) + 1))
-/* Extended Capabilities pointer from PCI base - section 5.3.6 */
-#define HCC_EXT_CAPS(p)		XHCI_HCC_EXT_CAPS(p)
-
-#define CTX_SIZE(_hcc)		(HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
-
-/* db_off bitmask - bits 0:1 reserved */
-#define	DBOFF_MASK	(~0x3)
-
-/* run_regs_off bitmask - bits 0:4 reserved */
-#define	RTSOFF_MASK	(~0x1f)
-
-/* HCCPARAMS2 - hcc_params2 - bitmasks */
-/* true: HC supports U3 entry Capability */
-#define	HCC2_U3C(p)		((p) & (1 << 0))
-/* true: HC supports Configure endpoint command Max exit latency too large */
-#define	HCC2_CMC(p)		((p) & (1 << 1))
-/* true: HC supports Force Save context Capability */
-#define	HCC2_FSC(p)		((p) & (1 << 2))
-/* true: HC supports Compliance Transition Capability */
-#define	HCC2_CTC(p)		((p) & (1 << 3))
-/* true: HC support Large ESIT payload Capability > 48k */
-#define	HCC2_LEC(p)		((p) & (1 << 4))
-/* true: HC support Configuration Information Capability */
-#define	HCC2_CIC(p)		((p) & (1 << 5))
-/* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
-#define	HCC2_ETC(p)		((p) & (1 << 6))
-
 /* Number of registers per port */
 #define	NUM_PORT_REGS	4
 
@@ -229,6 +149,9 @@
 #define CMD_ETE		(1 << 14)
 /* bits 15:31 are reserved (and should be preserved on writes). */
 
+#define XHCI_RESET_LONG_USEC		(10 * 1000 * 1000)
+#define XHCI_RESET_SHORT_USEC		(250 * 1000)
+
 /* IMAN - Interrupt Management Register */
 #define IMAN_IE		(1 << 1)
 #define IMAN_IP		(1 << 0)
@@ -288,181 +211,6 @@
 #define CONFIG_CIE		(1 << 9)
 /* bits 10:31 - reserved and should be preserved */
 
-/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
-/* true: device connected */
-#define PORT_CONNECT	(1 << 0)
-/* true: port enabled */
-#define PORT_PE		(1 << 1)
-/* bit 2 reserved and zeroed */
-/* true: port has an over-current condition */
-#define PORT_OC		(1 << 3)
-/* true: port reset signaling asserted */
-#define PORT_RESET	(1 << 4)
-/* Port Link State - bits 5:8
- * A read gives the current link PM state of the port,
- * a write with Link State Write Strobe set sets the link state.
- */
-#define PORT_PLS_MASK	(0xf << 5)
-#define XDEV_U0		(0x0 << 5)
-#define XDEV_U1		(0x1 << 5)
-#define XDEV_U2		(0x2 << 5)
-#define XDEV_U3		(0x3 << 5)
-#define XDEV_DISABLED	(0x4 << 5)
-#define XDEV_RXDETECT	(0x5 << 5)
-#define XDEV_INACTIVE	(0x6 << 5)
-#define XDEV_POLLING	(0x7 << 5)
-#define XDEV_RECOVERY	(0x8 << 5)
-#define XDEV_HOT_RESET	(0x9 << 5)
-#define XDEV_COMP_MODE	(0xa << 5)
-#define XDEV_TEST_MODE	(0xb << 5)
-#define XDEV_RESUME	(0xf << 5)
-
-/* true: port has power (see HCC_PPC) */
-#define PORT_POWER	(1 << 9)
-/* bits 10:13 indicate device speed:
- * 0 - undefined speed - port hasn't be initialized by a reset yet
- * 1 - full speed
- * 2 - low speed
- * 3 - high speed
- * 4 - super speed
- * 5-15 reserved
- */
-#define DEV_SPEED_MASK		(0xf << 10)
-#define	XDEV_FS			(0x1 << 10)
-#define	XDEV_LS			(0x2 << 10)
-#define	XDEV_HS			(0x3 << 10)
-#define	XDEV_SS			(0x4 << 10)
-#define	XDEV_SSP		(0x5 << 10)
-#define DEV_UNDEFSPEED(p)	(((p) & DEV_SPEED_MASK) == (0x0<<10))
-#define DEV_FULLSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_FS)
-#define DEV_LOWSPEED(p)		(((p) & DEV_SPEED_MASK) == XDEV_LS)
-#define DEV_HIGHSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_HS)
-#define DEV_SUPERSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_SS)
-#define DEV_SUPERSPEEDPLUS(p)	(((p) & DEV_SPEED_MASK) == XDEV_SSP)
-#define DEV_SUPERSPEED_ANY(p)	(((p) & DEV_SPEED_MASK) >= XDEV_SS)
-#define DEV_PORT_SPEED(p)	(((p) >> 10) & 0x0f)
-
-/* Bits 20:23 in the Slot Context are the speed for the device */
-#define	SLOT_SPEED_FS		(XDEV_FS << 10)
-#define	SLOT_SPEED_LS		(XDEV_LS << 10)
-#define	SLOT_SPEED_HS		(XDEV_HS << 10)
-#define	SLOT_SPEED_SS		(XDEV_SS << 10)
-#define	SLOT_SPEED_SSP		(XDEV_SSP << 10)
-/* Port Indicator Control */
-#define PORT_LED_OFF	(0 << 14)
-#define PORT_LED_AMBER	(1 << 14)
-#define PORT_LED_GREEN	(2 << 14)
-#define PORT_LED_MASK	(3 << 14)
-/* Port Link State Write Strobe - set this when changing link state */
-#define PORT_LINK_STROBE	(1 << 16)
-/* true: connect status change */
-#define PORT_CSC	(1 << 17)
-/* true: port enable change */
-#define PORT_PEC	(1 << 18)
-/* true: warm reset for a USB 3.0 device is done.  A "hot" reset puts the port
- * into an enabled state, and the device into the default state.  A "warm" reset
- * also resets the link, forcing the device through the link training sequence.
- * SW can also look at the Port Reset register to see when warm reset is done.
- */
-#define PORT_WRC	(1 << 19)
-/* true: over-current change */
-#define PORT_OCC	(1 << 20)
-/* true: reset change - 1 to 0 transition of PORT_RESET */
-#define PORT_RC		(1 << 21)
-/* port link status change - set on some port link state transitions:
- *  Transition				Reason
- *  ------------------------------------------------------------------------------
- *  - U3 to Resume			Wakeup signaling from a device
- *  - Resume to Recovery to U0		USB 3.0 device resume
- *  - Resume to U0			USB 2.0 device resume
- *  - U3 to Recovery to U0		Software resume of USB 3.0 device complete
- *  - U3 to U0				Software resume of USB 2.0 device complete
- *  - U2 to U0				L1 resume of USB 2.1 device complete
- *  - U0 to U0 (???)			L1 entry rejection by USB 2.1 device
- *  - U0 to disabled			L1 entry error with USB 2.1 device
- *  - Any state to inactive		Error on USB 3.0 port
- */
-#define PORT_PLC	(1 << 22)
-/* port configure error change - port failed to configure its link partner */
-#define PORT_CEC	(1 << 23)
-#define PORT_CHANGE_MASK	(PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
-				 PORT_RC | PORT_PLC | PORT_CEC)
-
-
-/* Cold Attach Status - xHC can set this bit to report device attached during
- * Sx state. Warm port reset should be perfomed to clear this bit and move port
- * to connected state.
- */
-#define PORT_CAS	(1 << 24)
-/* wake on connect (enable) */
-#define PORT_WKCONN_E	(1 << 25)
-/* wake on disconnect (enable) */
-#define PORT_WKDISC_E	(1 << 26)
-/* wake on over-current (enable) */
-#define PORT_WKOC_E	(1 << 27)
-/* bits 28:29 reserved */
-/* true: device is non-removable - for USB 3.0 roothub emulation */
-#define PORT_DEV_REMOVE	(1 << 30)
-/* Initiate a warm port reset - complete when PORT_WRC is '1' */
-#define PORT_WR		(1 << 31)
-
-/* We mark duplicate entries with -1 */
-#define DUPLICATE_ENTRY ((u8)(-1))
-
-/* Port Power Management Status and Control - port_power_base bitmasks */
-/* Inactivity timer value for transitions into U1, in microseconds.
- * Timeout can be up to 127us.  0xFF means an infinite timeout.
- */
-#define PORT_U1_TIMEOUT(p)	((p) & 0xff)
-#define PORT_U1_TIMEOUT_MASK	0xff
-/* Inactivity timer value for transitions into U2 */
-#define PORT_U2_TIMEOUT(p)	(((p) & 0xff) << 8)
-#define PORT_U2_TIMEOUT_MASK	(0xff << 8)
-/* Bits 24:31 for port testing */
-
-/* USB2 Protocol PORTSPMSC */
-#define	PORT_L1S_MASK		7
-#define	PORT_L1S_SUCCESS	1
-#define	PORT_RWE		(1 << 3)
-#define	PORT_HIRD(p)		(((p) & 0xf) << 4)
-#define	PORT_HIRD_MASK		(0xf << 4)
-#define	PORT_L1DS_MASK		(0xff << 8)
-#define	PORT_L1DS(p)		(((p) & 0xff) << 8)
-#define	PORT_HLE		(1 << 16)
-#define PORT_TEST_MODE_SHIFT	28
-
-/* USB3 Protocol PORTLI  Port Link Information */
-#define PORT_RX_LANES(p)	(((p) >> 16) & 0xf)
-#define PORT_TX_LANES(p)	(((p) >> 20) & 0xf)
-
-/* USB2 Protocol PORTHLPMC */
-#define PORT_HIRDM(p)((p) & 3)
-#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
-#define PORT_BESLD(p)(((p) & 0xf) << 10)
-
-/* use 512 microseconds as USB2 LPM L1 default timeout. */
-#define XHCI_L1_TIMEOUT		512
-
-/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
- * Safe to use with mixed HIRD and BESL systems (host and device) and is used
- * by other operating systems.
- *
- * XHCI 1.0 errata 8/14/12 Table 13 notes:
- * "Software should choose xHC BESL/BESLD field values that do not violate a
- * device's resume latency requirements,
- * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
- * or not program values < '4' if BLC = '0' and a BESL device is attached.
- */
-#define XHCI_DEFAULT_BESL	4
-
-/*
- * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
- * to complete link training. usually link trainig completes much faster
- * so check status 10 times with 36ms sleep in places we need to wait for
- * polling to complete.
- */
-#define XHCI_PORT_POLLING_LFPS_TIME  36
-
 /**
  * struct xhci_intr_reg - Interrupt Register Set
  * @irq_pending:	IMAN - Interrupt Management Register.  Used to enable
@@ -510,6 +258,9 @@
 /* Preserve bits 16:31 of erst_size */
 #define	ERST_SIZE_MASK		(0xffff << 16)
 
+/* erst_base bitmasks */
+#define ERST_BASE_RSVDP		(GENMASK_ULL(5, 0))
+
 /* erst_dequeue bitmasks */
 /* Dequeue ERST Segment Index (DESI) - Segment number (or alias)
  * where the current dequeue pointer lies.  This is an optional HW hint.
@@ -812,6 +563,8 @@
 	struct completion		*completion;
 	union xhci_trb			*command_trb;
 	struct list_head		cmd_list;
+	/* xHCI command response timeout in milliseconds */
+	unsigned int			timeout_ms;
 };
 
 /* drop context bitmasks */
@@ -930,6 +683,7 @@
 	 * have to restore the device state to the previous state
 	 */
 	struct xhci_ring		*new_ring;
+	unsigned int			err_count;
 	unsigned int			ep_state;
 #define SET_DEQ_PENDING		(1 << 0)
 #define EP_HALTED		(1 << 1)	/* For stall handling */
@@ -965,6 +719,7 @@
 	/* Bandwidth checking storage */
 	struct xhci_bw_info	bw_info;
 	struct list_head	bw_endpoint_list;
+	unsigned long		stop_time;
 	/* Isoch Frame ID checking storage */
 	int			next_frame_id;
 	/* Use new Isoch TRB layout needed for extended TBC support */
@@ -1278,7 +1033,7 @@
 /* Set TR Dequeue Pointer command TRB fields, 6.4.3.9 */
 #define TRB_TO_STREAM_ID(p)		((((p) & (0xffff << 16)) >> 16))
 #define STREAM_ID_FOR_TRB(p)		((((p)) & 0xffff) << 16)
-#define SCT_FOR_TRB(p)			(((p) << 1) & 0x7)
+#define SCT_FOR_TRB(p)			(((p) & 0x7) << 1)
 
 /* Link TRB specific fields */
 #define TRB_TC			(1<<1)
@@ -1552,6 +1307,7 @@
 	TD_DIRTY = 0,
 	TD_HALTED,
 	TD_CLEARING_CACHE,
+	TD_CLEARING_CACHE_DEFERRED,
 	TD_CLEARED,
 };
 
@@ -1568,11 +1324,15 @@
 	struct xhci_segment	*bounce_seg;
 	/* actual_length of the URB has already been set */
 	bool			urb_length_set;
+	bool			error_mid_td;
 	unsigned int		num_trbs;
 };
 
-/* xHCI command default timeout value */
-#define XHCI_CMD_DEFAULT_TIMEOUT	(5 * HZ)
+/*
+ * xHCI command default timeout value in milliseconds.
+ * USB 3.2 spec, section 9.2.6.1
+ */
+#define XHCI_CMD_DEFAULT_TIMEOUT	5000
 
 /* command descriptor */
 struct xhci_cd {
@@ -1626,7 +1386,6 @@
 	 * if we own the TRB (if we are the consumer).  See section 4.9.1.
 	 */
 	u32			cycle_state;
-	unsigned int            err_count;
 	unsigned int		stream_id;
 	unsigned int		num_segs;
 	unsigned int		num_trbs_free;
@@ -1635,6 +1394,9 @@
 	enum xhci_ring_type	type;
 	bool			last_td_was_short;
 	struct radix_tree_root	*trb_address_map;
+	struct timer_list	stream_timer;
+	bool			stream_timeout_handler;
+	struct xhci_hcd		*xhci;
 };
 
 struct xhci_erst_entry {
@@ -1683,11 +1445,6 @@
 	u32	dev_nt;
 	u64	dcbaa_ptr;
 	u32	config_reg;
-	u32	irq_pending;
-	u32	irq_control;
-	u32	erst_size;
-	u64	erst_base;
-	u64	erst_dequeue;
 };
 
 /* Use for lpm */
@@ -1705,16 +1462,22 @@
 	u32			port_c_suspend;
 	u32			suspended_ports;
 	u32			port_remote_wakeup;
-	unsigned long		resume_done[USB_MAXCHILDREN];
 	/* which ports have started to resume */
 	unsigned long		resuming_ports;
-	/* Which ports are waiting on RExit to U0 transition. */
-	unsigned long		rexit_ports;
-	struct completion	rexit_done[USB_MAXCHILDREN];
-	struct completion	u3exit_done[USB_MAXCHILDREN];
 };
 
-
+struct xhci_interrupter {
+	struct xhci_ring	*event_ring;
+	struct xhci_erst	erst;
+	struct xhci_intr_reg __iomem *ir_set;
+	unsigned int		intr_num;
+	/* For interrupter registers save and restore over suspend/resume */
+	u32	s3_irq_pending;
+	u32	s3_irq_control;
+	u32	s3_erst_size;
+	u64	s3_erst_base;
+	u64	s3_erst_dequeue;
+};
 /*
  * It can take up to 20 ms to transition from RExit to U0 on the
  * Intel Lynx Point LP xHCI host.
@@ -1734,6 +1497,11 @@
 	int			hcd_portnum;
 	struct xhci_hub		*rhub;
 	struct xhci_port_cap	*port_cap;
+	unsigned int		lpm_incapable:1;
+	unsigned long		resume_timestamp;
+	bool			rexit_active;
+	struct completion	rexit_done;
+	struct completion	u3exit_done;
 };
 
 struct xhci_hub {
@@ -1756,8 +1524,6 @@
 	struct xhci_op_regs __iomem *op_regs;
 	struct xhci_run_regs __iomem *run_regs;
 	struct xhci_doorbell_array __iomem *dba;
-	/* Our HCD's current interrupter register set */
-	struct	xhci_intr_reg __iomem *ir_set;
 
 	/* Cached register copies of read-only HC data */
 	__u32		hcs_params1;
@@ -1772,7 +1538,7 @@
 	u8		sbrn;
 	u16		hci_version;
 	u8		max_slots;
-	u8		max_interrupters;
+	u16		max_interrupters;
 	u8		max_ports;
 	u8		isoc_threshold;
 	/* imod_interval in ns (I * 250ns) */
@@ -1792,6 +1558,7 @@
 	struct reset_control *reset;
 	/* data structures */
 	struct xhci_device_context_array *dcbaa;
+	struct xhci_interrupter *interrupter;
 	struct xhci_ring	*cmd_ring;
 	unsigned int            cmd_ring_state;
 #define CMD_RING_STATE_RUNNING         (1 << 0)
@@ -1802,8 +1569,7 @@
 	struct delayed_work	cmd_timer;
 	struct completion	cmd_ring_stop_completion;
 	struct xhci_command	*current_cmd;
-	struct xhci_ring	*event_ring;
-	struct xhci_erst	erst;
+
 	/* Scratchpad */
 	struct xhci_scratchpad  *scratchpad;
 	/* Store LPM test failed devices' information */
@@ -1827,7 +1593,7 @@
 
 	/* Host controller watchdog timer structures */
 	unsigned int		xhc_state;
-
+	unsigned long		run_graceperiod;
 	u32			command;
 	struct s3_save		s3;
 /* Host controller is dying - not responding to commands. "I'm not dead yet!"
@@ -1898,8 +1664,15 @@
 #define XHCI_DISABLE_SPARSE	BIT_ULL(38)
 #define XHCI_SG_TRB_CACHE_SIZE_QUIRK	BIT_ULL(39)
 #define XHCI_NO_SOFT_RETRY	BIT_ULL(40)
-#define XHCI_BROKEN_D3COLD	BIT_ULL(41)
+#define XHCI_BROKEN_D3COLD_S2I	BIT_ULL(41)
 #define XHCI_EP_CTX_BROKEN_DCS	BIT_ULL(42)
+#define XHCI_SUSPEND_RESUME_CLKS	BIT_ULL(43)
+#define XHCI_RESET_TO_DEFAULT	BIT_ULL(44)
+#define XHCI_TRB_OVERFETCH	BIT_ULL(45)
+#define XHCI_ZHAOXIN_HOST	BIT_ULL(46)
+#define XHCI_WRITE_64_HI_LO	BIT_ULL(47)
+#define XHCI_CDNS_SCTX_QUIRK	BIT_ULL(48)
+#define XHCI_STREAM_QUIRK	BIT_ULL(49) /* FIXME this is wrong */
 
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
@@ -1943,6 +1716,8 @@
 			     struct usb_host_endpoint *ep);
 	int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
 	void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
+	int (*update_hub_device)(struct usb_hcd *hcd, struct usb_device *hdev,
+			    struct usb_tt *tt, gfp_t mem_flags);
 };
 
 #define	XHCI_CFC_DELAY		10
@@ -2083,11 +1858,13 @@
 
 /* xHCI host controller glue */
 typedef void (*xhci_get_quirks_t)(struct device *, struct xhci_hcd *);
-int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, int usec);
+typedef void (*host_wakeup_t)(struct device *dev, bool wakeup);
+void dwc3_host_wakeup_capable(struct device *dev, bool wakeup);
+int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, u64 timeout_us);
 void xhci_quiesce(struct xhci_hcd *xhci);
 int xhci_halt(struct xhci_hcd *xhci);
 int xhci_start(struct xhci_hcd *xhci);
-int xhci_reset(struct xhci_hcd *xhci);
+int xhci_reset(struct xhci_hcd *xhci, u64 timeout_us);
 int xhci_run(struct usb_hcd *hcd);
 int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks);
 void xhci_shutdown(struct usb_hcd *hcd);
@@ -2099,6 +1876,8 @@
 		       struct usb_host_endpoint *ep);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
+int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
+			   struct usb_tt *tt, gfp_t mem_flags);
 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id);
 int xhci_ext_cap_init(struct xhci_hcd *xhci);
 
@@ -2150,6 +1929,7 @@
 			       unsigned int ep_index, unsigned int stream_id,
 			       struct xhci_td *td);
 void xhci_stop_endpoint_command_watchdog(struct timer_list *t);
+void xhci_stream_timeout(struct timer_list *unused);
 void xhci_handle_command_timeout(struct work_struct *work);
 
 void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int slot_id,
@@ -2160,6 +1940,7 @@
 void xhci_cleanup_command_queue(struct xhci_hcd *xhci);
 void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring);
 unsigned int count_trbs(u64 addr, u64 len);
+void xhci_process_cancelled_tds(struct xhci_virt_ep *ep);
 
 /* xHCI roothub code */
 void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port,
@@ -2390,7 +2171,7 @@
 			field3 & TRB_CYCLE ? 'C' : 'c');
 		break;
 	case TRB_STOP_RING:
-		sprintf(str,
+		snprintf(str, size,
 			"%s: slot %d sp %d ep %d flags %c",
 			xhci_trb_type_string(type),
 			TRB_TO_SLOT_ID(field3),
@@ -2467,6 +2248,8 @@
 	unsigned int	bit;
 	int		ret = 0;
 
+	str[0] = '\0';
+
 	if (drop) {
 		ret = sprintf(str, "Drop:");
 		for_each_set_bit(bit, &drop, 32)
@@ -2624,8 +2407,11 @@
 {
 	int ret = 0;
 
+	ret = sprintf(str, " 0x%08x", usbsts);
+
 	if (usbsts == ~(u32)0)
-		return " 0xffffffff";
+		return str;
+
 	if (usbsts & STS_HALT)
 		ret += sprintf(str + ret, " HCHalted");
 	if (usbsts & STS_FATAL)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/isp1760/isp1760-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/isp1760/isp1760-core.c
@@ -251,6 +251,8 @@
 	[HW_DM_PULLDOWN]	= REG_FIELD(ISP176x_HC_OTG_CTRL, 2, 2),
 	[HW_DP_PULLDOWN]	= REG_FIELD(ISP176x_HC_OTG_CTRL, 1, 1),
 	[HW_DP_PULLUP]		= REG_FIELD(ISP176x_HC_OTG_CTRL, 0, 0),
+	/* Make sure the array is sized properly during compilation */
+	[HC_FIELD_MAX]		= {},
 };
 
 static const struct reg_field isp1763_hc_reg_fields[] = {
@@ -321,6 +323,8 @@
 	[HW_DM_PULLDOWN_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 2, 2),
 	[HW_DP_PULLDOWN_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 1, 1),
 	[HW_DP_PULLUP_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 0, 0),
+	/* Make sure the array is sized properly during compilation */
+	[HC_FIELD_MAX]		= {},
 };
 
 static const struct regmap_range isp1763_hc_volatile_ranges[] = {
@@ -405,6 +409,8 @@
 	[DC_CHIP_ID_HIGH]	= REG_FIELD(ISP176x_DC_CHIPID, 16, 31),
 	[DC_CHIP_ID_LOW]	= REG_FIELD(ISP176x_DC_CHIPID, 0, 15),
 	[DC_SCRATCH]		= REG_FIELD(ISP176x_DC_SCRATCH, 0, 15),
+	/* Make sure the array is sized properly during compilation */
+	[DC_FIELD_MAX]		= {},
 };
 
 static const struct regmap_range isp1763_dc_volatile_ranges[] = {
@@ -458,6 +464,8 @@
 	[DC_CHIP_ID_HIGH]	= REG_FIELD(ISP1763_DC_CHIPID_HIGH, 0, 15),
 	[DC_CHIP_ID_LOW]	= REG_FIELD(ISP1763_DC_CHIPID_LOW, 0, 15),
 	[DC_SCRATCH]		= REG_FIELD(ISP1763_DC_SCRATCH, 0, 15),
+	/* Make sure the array is sized properly during compilation */
+	[DC_FIELD_MAX]		= {},
 };
 
 static const struct regmap_config isp1763_dc_regmap_conf = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/Kconfig
@@ -242,6 +242,22 @@
 	  parameters may be set in devicetree or platform data.
 	  Say Y or M here if you need to configure such a device via SMBus.
 
+config USB_USB2244
+	tristate "Microchip USB2244 Ultra Fast USB 2.0 SD driver"
+	depends on GPIOLIB
+	help
+	  This option enables support for Microchip USB2244 Ultra Fast USB 2.0
+	  SD controller. This driver reset the gpio pin makes controller out of
+	  reset.
+
+config USB_USB5744
+	tristate "Microchip USB5744 Hub driver"
+	depends on I2C
+	depends on GPIOLIB
+	help
+	  This option enables support for Microchip USB5744 Hub. This driver
+	  reset the hub using gpio pin and configure hub via i2c.
+
 config USB_HSIC_USB3503
 	tristate "USB3503 HSIC to USB20 Driver"
 	depends on I2C
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/Makefile
@@ -25,6 +25,8 @@
 obj-$(CONFIG_USB_SEVSEG)		+= usbsevseg.o
 obj-$(CONFIG_USB_YUREX)			+= yurex.o
 obj-$(CONFIG_USB_HUB_USB251XB)		+= usb251xb.o
+obj-$(CONFIG_USB_USB2244)		+= usb2244.o
+obj-$(CONFIG_USB_USB5744)		+= usb5744.o
 obj-$(CONFIG_USB_HSIC_USB3503)		+= usb3503.o
 obj-$(CONFIG_USB_HSIC_USB4604)		+= usb4604.o
 obj-$(CONFIG_USB_CHAOSKEY)		+= chaoskey.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/appledisplay.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/appledisplay.c
@@ -107,7 +107,12 @@
 	case ACD_BTN_BRIGHT_UP:
 	case ACD_BTN_BRIGHT_DOWN:
 		pdata->button_pressed = 1;
-		schedule_delayed_work(&pdata->work, 0);
+		/*
+		 * there is a window during which no device
+		 * is registered
+		 */
+		if (pdata->bd )
+			schedule_delayed_work(&pdata->work, 0);
 		break;
 	case ACD_BTN_NONE:
 	default:
@@ -202,6 +207,7 @@
 	const struct usb_device_id *id)
 {
 	struct backlight_properties props;
+	struct backlight_device *backlight;
 	struct appledisplay *pdata;
 	struct usb_device *udev = interface_to_usbdev(iface);
 	struct usb_endpoint_descriptor *endpoint;
@@ -272,13 +278,14 @@
 	memset(&props, 0, sizeof(struct backlight_properties));
 	props.type = BACKLIGHT_RAW;
 	props.max_brightness = 0xff;
-	pdata->bd = backlight_device_register(bl_name, NULL, pdata,
+	backlight = backlight_device_register(bl_name, NULL, pdata,
 					      &appledisplay_bl_data, &props);
-	if (IS_ERR(pdata->bd)) {
+	if (IS_ERR(backlight)) {
 		dev_err(&iface->dev, "Backlight registration failed\n");
-		retval = PTR_ERR(pdata->bd);
+		retval = PTR_ERR(backlight);
 		goto error;
 	}
+	pdata->bd = backlight;
 
 	/* Try to get brightness */
 	brightness = appledisplay_bl_get_brightness(pdata->bd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/chaoskey.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/chaoskey.c
@@ -27,6 +27,8 @@
 static int chaoskey_rng_read(struct hwrng *rng, void *data,
 			     size_t max, bool wait);
 
+static DEFINE_MUTEX(chaoskey_list_lock);
+
 #define usb_dbg(usb_if, format, arg...) \
 	dev_dbg(&(usb_if)->dev, format, ## arg)
 
@@ -234,6 +236,7 @@
 	usb_deregister_dev(interface, &chaoskey_class);
 
 	usb_set_intfdata(interface, NULL);
+	mutex_lock(&chaoskey_list_lock);
 	mutex_lock(&dev->lock);
 
 	dev->present = false;
@@ -245,6 +248,7 @@
 	} else
 		mutex_unlock(&dev->lock);
 
+	mutex_unlock(&chaoskey_list_lock);
 	usb_dbg(interface, "disconnect done");
 }
 
@@ -252,6 +256,7 @@
 {
 	struct chaoskey *dev;
 	struct usb_interface *interface;
+	int rv = 0;
 
 	/* get the interface from minor number and driver information */
 	interface = usb_find_interface(&chaoskey_driver, iminor(inode));
@@ -267,18 +272,23 @@
 	}
 
 	file->private_data = dev;
+	mutex_lock(&chaoskey_list_lock);
 	mutex_lock(&dev->lock);
-	++dev->open;
+	if (dev->present)
+		++dev->open;
+	else
+		rv = -ENODEV;
 	mutex_unlock(&dev->lock);
+	mutex_unlock(&chaoskey_list_lock);
 
-	usb_dbg(interface, "open success");
-	return 0;
+	return rv;
 }
 
 static int chaoskey_release(struct inode *inode, struct file *file)
 {
 	struct chaoskey *dev = file->private_data;
 	struct usb_interface *interface;
+	int rv = 0;
 
 	if (dev == NULL)
 		return -ENODEV;
@@ -287,14 +297,15 @@
 
 	usb_dbg(interface, "release");
 
+	mutex_lock(&chaoskey_list_lock);
 	mutex_lock(&dev->lock);
 
 	usb_dbg(interface, "open count at release is %d", dev->open);
 
 	if (dev->open <= 0) {
 		usb_dbg(interface, "invalid open count (%d)", dev->open);
-		mutex_unlock(&dev->lock);
-		return -ENODEV;
+		rv = -ENODEV;
+		goto bail;
 	}
 
 	--dev->open;
@@ -303,13 +314,15 @@
 		if (dev->open == 0) {
 			mutex_unlock(&dev->lock);
 			chaoskey_free(dev);
-		} else
-			mutex_unlock(&dev->lock);
-	} else
-		mutex_unlock(&dev->lock);
-
+			goto destruction;
+		}
+	}
+bail:
+	mutex_unlock(&dev->lock);
+destruction:
+	mutex_unlock(&chaoskey_list_lock);
 	usb_dbg(interface, "release success");
-	return 0;
+	return rv;
 }
 
 static void chaos_read_callback(struct urb *urb)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/cypress_cy7c63.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/cypress_cy7c63.c
@@ -88,6 +88,9 @@
 				 USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_OTHER,
 				 address, data, iobuf, CYPRESS_MAX_REQSIZE,
 				 USB_CTRL_GET_TIMEOUT);
+	/* we must not process garbage */
+	if (retval < 2)
+		goto err_buf;
 
 	/* store returned data (more READs to be added) */
 	switch (request) {
@@ -107,6 +110,7 @@
 			break;
 	}
 
+err_buf:
 	kfree(iobuf);
 error:
 	return retval;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/ftdi-elan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/ftdi-elan.c
@@ -202,6 +202,7 @@
 	mutex_unlock(&ftdi_module_lock);
 	kfree(ftdi->bulk_in_buffer);
 	ftdi->bulk_in_buffer = NULL;
+	kfree(ftdi);
 }
 
 static void ftdi_elan_put_kref(struct usb_ftdi *ftdi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/idmouse.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/idmouse.c
@@ -177,10 +177,6 @@
 		bytes_read += bulk_read;
 	}
 
-	/* reset the device */
-reset:
-	ftip_command(dev, FTIP_RELEASE, 0, 0);
-
 	/* check for valid image */
 	/* right border should be black (0x00) */
 	for (bytes_read = sizeof(HEADER)-1 + WIDTH-1; bytes_read < IMGSIZE; bytes_read += WIDTH)
@@ -192,6 +188,10 @@
 		if (dev->bulk_in_buffer[bytes_read] != 0xFF)
 			return -EAGAIN;
 
+	/* reset the device */
+reset:
+	ftip_command(dev, FTIP_RELEASE, 0, 0);
+
 	/* should be IMGSIZE == 65040 */
 	dev_dbg(&dev->interface->dev, "read %d bytes fingerprint data\n",
 		bytes_read);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/iowarrior.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/iowarrior.c
@@ -99,10 +99,6 @@
 /*    globals   */
 /*--------------*/
 
-/*
- *  USB spec identifies 5 second timeouts.
- */
-#define GET_TIMEOUT 5
 #define USB_REQ_GET_REPORT  0x01
 //#if 0
 static int usb_get_report(struct usb_device *dev,
@@ -114,7 +110,7 @@
 			       USB_DIR_IN | USB_TYPE_CLASS |
 			       USB_RECIP_INTERFACE, (type << 8) + id,
 			       inter->desc.bInterfaceNumber, buf, size,
-			       GET_TIMEOUT*HZ);
+			       USB_CTRL_GET_TIMEOUT);
 }
 //#endif
 
@@ -129,7 +125,7 @@
 			       USB_TYPE_CLASS | USB_RECIP_INTERFACE,
 			       (type << 8) + id,
 			       intf->cur_altsetting->desc.bInterfaceNumber, buf,
-			       size, HZ);
+			       size, 1000);
 }
 
 /*---------------------*/
@@ -281,28 +277,45 @@
 	struct iowarrior *dev;
 	int read_idx;
 	int offset;
+	int retval;
 
 	dev = file->private_data;
 
+	if (file->f_flags & O_NONBLOCK) {
+		retval = mutex_trylock(&dev->mutex);
+		if (!retval)
+			return -EAGAIN;
+	} else {
+		retval = mutex_lock_interruptible(&dev->mutex);
+		if (retval)
+			return -ERESTARTSYS;
+	}
+
 	/* verify that the device wasn't unplugged */
-	if (!dev || !dev->present)
-		return -ENODEV;
+	if (!dev->present) {
+		retval = -ENODEV;
+		goto exit;
+	}
 
 	dev_dbg(&dev->interface->dev, "minor %d, count = %zd\n",
 		dev->minor, count);
 
 	/* read count must be packet size (+ time stamp) */
 	if ((count != dev->report_size)
-	    && (count != (dev->report_size + 1)))
-		return -EINVAL;
+	    && (count != (dev->report_size + 1))) {
+		retval = -EINVAL;
+		goto exit;
+	}
 
 	/* repeat until no buffer overrun in callback handler occur */
 	do {
 		atomic_set(&dev->overflow_flag, 0);
 		if ((read_idx = read_index(dev)) == -1) {
 			/* queue empty */
-			if (file->f_flags & O_NONBLOCK)
-				return -EAGAIN;
+			if (file->f_flags & O_NONBLOCK) {
+				retval = -EAGAIN;
+				goto exit;
+			}
 			else {
 				//next line will return when there is either new data, or the device is unplugged
 				int r = wait_event_interruptible(dev->read_wait,
@@ -313,28 +326,37 @@
 								  -1));
 				if (r) {
 					//we were interrupted by a signal
-					return -ERESTART;
+					retval = -ERESTART;
+					goto exit;
 				}
 				if (!dev->present) {
 					//The device was unplugged
-					return -ENODEV;
+					retval = -ENODEV;
+					goto exit;
 				}
 				if (read_idx == -1) {
 					// Can this happen ???
-					return 0;
+					retval = 0;
+					goto exit;
 				}
 			}
 		}
 
 		offset = read_idx * (dev->report_size + 1);
 		if (copy_to_user(buffer, dev->read_queue + offset, count)) {
-			return -EFAULT;
+			retval = -EFAULT;
+			goto exit;
 		}
 	} while (atomic_read(&dev->overflow_flag));
 
 	read_idx = ++read_idx == MAX_INTERRUPT_BUFFER ? 0 : read_idx;
 	atomic_set(&dev->read_idx, read_idx);
+	mutex_unlock(&dev->mutex);
 	return count;
+
+exit:
+	mutex_unlock(&dev->mutex);
+	return retval;
 }
 
 /*
@@ -818,7 +840,7 @@
 			break;
 
 		case USB_DEVICE_ID_CODEMERCS_IOW100:
-			dev->report_size = 13;
+			dev->report_size = 12;
 			break;
 		}
 	}
@@ -890,7 +912,6 @@
 static void iowarrior_disconnect(struct usb_interface *interface)
 {
 	struct iowarrior *dev = usb_get_intfdata(interface);
-	int minor = dev->minor;
 
 	usb_deregister_dev(interface, &iowarrior_class);
 
@@ -914,9 +935,6 @@
 		mutex_unlock(&dev->mutex);
 		iowarrior_delete(dev);
 	}
-
-	dev_info(&interface->dev, "I/O-Warror #%d now disconnected\n",
-		 minor - IOWARRIOR_MINOR_BASE);
 }
 
 /* usb specific object needed to register this driver with the usb subsystem */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/sisusbvga/sisusb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/sisusbvga/sisusb.c
@@ -3014,6 +3014,20 @@
 	struct usb_device *dev = interface_to_usbdev(intf);
 	struct sisusb_usb_data *sisusb;
 	int retval = 0, i;
+	static const u8 ep_addresses[] = {
+		SISUSB_EP_GFX_IN | USB_DIR_IN,
+		SISUSB_EP_GFX_OUT | USB_DIR_OUT,
+		SISUSB_EP_GFX_BULK_OUT | USB_DIR_OUT,
+		SISUSB_EP_GFX_LBULK_OUT | USB_DIR_OUT,
+		SISUSB_EP_BRIDGE_IN | USB_DIR_IN,
+		SISUSB_EP_BRIDGE_OUT | USB_DIR_OUT,
+		0};
+
+	/* Are the expected endpoints present? */
+	if (!usb_check_bulk_endpoints(intf, ep_addresses)) {
+		dev_err(&intf->dev, "Invalid USB2VGA device\n");
+		return -EINVAL;
+	}
 
 	dev_info(&dev->dev, "USB2VGA dongle found at address %d\n",
 			dev->devnum);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/usb2244.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/usb2244.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the Microchip USB2244 Ultra Fast USB 2.0 Multi-Format,
+ * SD/MMC, and MS Flash Media Controllers
+ *
+ * Copyright (c) 2021 Xilinx, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+
+struct usb2244 {
+	struct gpio_desc *reset_gpio;
+};
+
+static int usb2244_init_hw(struct device *dev, struct usb2244 *data)
+{
+	data = devm_kzalloc(dev, sizeof(struct usb2244), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(data->reset_gpio)) {
+		return dev_err_probe(dev, PTR_ERR(data->reset_gpio),
+				     "Failed to request reset GPIO\n");
+	}
+
+	/* Toggle RESET_N to reset the hub. */
+	gpiod_set_value_cansleep(data->reset_gpio, 1);
+	usleep_range(5, 10);
+	gpiod_set_value_cansleep(data->reset_gpio, 0);
+	msleep(5);
+
+	return 0;
+}
+
+static int usb2244_probe(struct platform_device *pdev)
+{
+	struct usb2244 *data = NULL;
+
+	/* Trigger gpio reset to the hub. */
+	return usb2244_init_hw(&pdev->dev, data);
+}
+
+static const struct of_device_id usb2244_of_match[] = {
+	{ .compatible = "microchip,usb2244", },
+	{ }
+};
+
+static struct platform_driver usb2244_driver = {
+	.driver = {
+		.name = "microchip,usb2244",
+		.of_match_table	= usb2244_of_match,
+	},
+	.probe = usb2244_probe,
+};
+
+module_platform_driver(usb2244_driver);
+
+MODULE_AUTHOR("Piyush Mehta <piyush.mehta@xilinx.com>");
+MODULE_DESCRIPTION("USB2244 Ultra Fast SD-Controller");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/usb5744.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/usb5744.c
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the Microchip USB5744 4-port hub.
+ *
+ * Copyright (c) 2021 Xilinx, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/byteorder/generic.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+
+/* chip address - usb5744 */
+#define I2C_ADDR		0x2d
+/* chip type and driver name */
+#define DRIVER_NAME		"usb5744"
+
+struct usb5744 {
+	struct gpio_desc *reset_gpio;
+};
+
+static int usb5744_init_hw(struct device *dev, struct usb5744 *data)
+{
+	data = devm_kzalloc(dev, sizeof(struct usb5744), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(data->reset_gpio)) {
+		return dev_err_probe(dev, PTR_ERR(data->reset_gpio),
+				     "Failed to request reset GPIO\n");
+	}
+
+	/* Toggle RESET_N to reset the hub. */
+	gpiod_set_value_cansleep(data->reset_gpio, 1);
+	/* Delay - Sleep for an approximate time 5 to 20 usecs */
+	usleep_range(5, 20);
+	gpiod_set_value_cansleep(data->reset_gpio, 0);
+	msleep(5);
+
+	return 0;
+}
+
+static int usb5744_i2c_dev_init(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct usb5744 *data = NULL;
+	int ret = 0;
+
+	i2c_set_clientdata(client, data);
+
+	/* Trigger gpio reset to the hub. */
+	ret = usb5744_init_hw(dev, data);
+	if (ret)
+		return ret;
+
+	/* Send SMBus command to boot hub. */
+	ret = i2c_smbus_write_word_data(client, 0xAA, htons(0x5600));
+	if (ret < 0)
+		dev_err(dev, "Sending boot command failed");
+
+	return ret;
+}
+
+static int usb5744_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	/* I2C device init and gpio reset to the hub. */
+	return usb5744_i2c_dev_init(client);
+}
+
+static int usb5744_platform_probe(struct platform_device *pdev)
+{
+	struct usb5744 *data = NULL;
+	struct device_node *i2c_node;
+	struct i2c_adapter *adapter;
+	struct i2c_client *client;
+	struct i2c_board_info info = {
+		.type = DRIVER_NAME,
+		.addr = I2C_ADDR,
+	};
+
+	i2c_node = of_parse_phandle(pdev->dev.of_node, "i2c-bus", 0);
+	if (i2c_node) {
+		adapter = of_find_i2c_adapter_by_node(i2c_node);
+		of_node_put(i2c_node);
+
+		if (!adapter)
+			return -EPROBE_DEFER;
+
+		client = i2c_new_client_device(adapter, &info);
+		return usb5744_i2c_dev_init(client);
+	}
+
+	/* Trigger gpio reset to the hub. */
+	return usb5744_init_hw(&pdev->dev, data);
+}
+
+static const struct i2c_device_id usb5744_id[] = {
+	{ DRIVER_NAME, 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, usb5744_id);
+
+static struct i2c_driver usb5744_i2c_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+	},
+	.probe = usb5744_i2c_probe,
+	.id_table = usb5744_id,
+};
+
+static const struct of_device_id usb5744_platform_id[] = {
+	{ .compatible = "microchip,usb5744", },
+	{ }
+};
+
+static struct platform_driver usb5744_platform_driver = {
+	.driver = {
+		.name = "microchip,usb5744",
+		.of_match_table	= usb5744_platform_id,
+	},
+	.probe = usb5744_platform_probe,
+};
+
+static int __init usb5744_init(void)
+{
+	int err;
+
+	err = i2c_add_driver(&usb5744_i2c_driver);
+	if (err != 0)
+		pr_err("usb5744: Failed to register I2C driver: %d\n", err);
+
+	err = platform_driver_register(&usb5744_platform_driver);
+	if (err != 0)
+		pr_err("usb5744: Failed to register platform driver: %d\n",
+		       err);
+	return 0;
+}
+module_init(usb5744_init);
+
+static void __exit usb5744_exit(void)
+{
+	platform_driver_unregister(&usb5744_platform_driver);
+	i2c_del_driver(&usb5744_i2c_driver);
+}
+module_exit(usb5744_exit);
+
+MODULE_AUTHOR("Piyush Mehta <piyush.mehta@xilinx.com>");
+MODULE_DESCRIPTION("USB5744 Hub");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/uss720.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/uss720.c
@@ -71,6 +71,7 @@
 
 	dev_dbg(&priv->usbdev->dev, "destroying priv datastructure\n");
 	usb_put_dev(priv->usbdev);
+	priv->usbdev = NULL;
 	kfree(priv);
 }
 
@@ -676,7 +677,7 @@
 	struct parport_uss720_private *priv;
 	struct parport *pp;
 	unsigned char reg;
-	int i;
+	int ret;
 
 	dev_dbg(&intf->dev, "probe: vendor id 0x%x, device id 0x%x\n",
 		le16_to_cpu(usbdev->descriptor.idVendor),
@@ -687,8 +688,8 @@
 		usb_put_dev(usbdev);
 		return -ENODEV;
 	}
-	i = usb_set_interface(usbdev, intf->altsetting->desc.bInterfaceNumber, 2);
-	dev_dbg(&intf->dev, "set interface result %d\n", i);
+	ret = usb_set_interface(usbdev, intf->altsetting->desc.bInterfaceNumber, 2);
+	dev_dbg(&intf->dev, "set interface result %d\n", ret);
 
 	interface = intf->cur_altsetting;
 
@@ -724,19 +725,24 @@
 	set_1284_register(pp, 7, 0x00, GFP_KERNEL);
 	set_1284_register(pp, 6, 0x30, GFP_KERNEL);  /* PS/2 mode */
 	set_1284_register(pp, 2, 0x0c, GFP_KERNEL);
-	/* debugging */
-	get_1284_register(pp, 0, &reg, GFP_KERNEL);
+
+	/* The Belkin F5U002 Rev 2 P80453-B USB parallel port adapter shares the
+	 * device ID 050d:0002 with some other device that works with this
+	 * driver, but it itself does not. Detect and handle the bad cable
+	 * here. */
+	ret = get_1284_register(pp, 0, &reg, GFP_KERNEL);
 	dev_dbg(&intf->dev, "reg: %7ph\n", priv->reg);
+	if (ret < 0)
+		return ret;
 
-	i = usb_find_last_int_in_endpoint(interface, &epd);
-	if (!i) {
+	ret = usb_find_last_int_in_endpoint(interface, &epd);
+	if (!ret) {
 		dev_dbg(&intf->dev, "epaddr %d interval %d\n",
 				epd->bEndpointAddress, epd->bInterval);
 	}
 	parport_announce_port(pp);
 
 	usb_set_intfdata(intf, pp);
-	usb_put_dev(usbdev);
 	return 0;
 
 probe_abort:
@@ -754,7 +760,6 @@
 	usb_set_intfdata(intf, NULL);
 	if (pp) {
 		priv = pp->private_data;
-		priv->usbdev = NULL;
 		priv->pp = NULL;
 		dev_dbg(&intf->dev, "parport_remove_port\n");
 		parport_remove_port(pp);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/misc/yurex.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/misc/yurex.c
@@ -441,7 +441,10 @@
 	if (count == 0)
 		goto error;
 
-	mutex_lock(&dev->io_mutex);
+	retval = mutex_lock_interruptible(&dev->io_mutex);
+	if (retval < 0)
+		return -EINTR;
+
 	if (dev->disconnected) {		/* already disconnected */
 		mutex_unlock(&dev->io_mutex);
 		retval = -ENODEV;
@@ -507,8 +510,11 @@
 			__func__, retval);
 		goto error;
 	}
-	if (set && timeout)
+	if (set && timeout) {
+		spin_lock_irq(&dev->lock);
 		dev->bbu = c2;
+		spin_unlock_irq(&dev->lock);
+	}
 	return timeout ? count : -EIO;
 
 error:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/mon/mon_bin.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/mon/mon_bin.c
@@ -1247,14 +1247,19 @@
 	struct mon_reader_bin *rp = vmf->vma->vm_private_data;
 	unsigned long offset, chunk_idx;
 	struct page *pageptr;
+	unsigned long flags;
 
+	spin_lock_irqsave(&rp->b_lock, flags);
 	offset = vmf->pgoff << PAGE_SHIFT;
-	if (offset >= rp->b_size)
+	if (offset >= rp->b_size) {
+		spin_unlock_irqrestore(&rp->b_lock, flags);
 		return VM_FAULT_SIGBUS;
+	}
 	chunk_idx = offset / CHUNK_SIZE;
 	pageptr = rp->b_vec[chunk_idx].pg;
 	get_page(pageptr);
 	vmf->page = pageptr;
+	spin_unlock_irqrestore(&rp->b_lock, flags);
 	return 0;
 }
 
@@ -1268,6 +1273,11 @@
 {
 	/* don't do anything here: "fault" will set up page table entries */
 	vma->vm_ops = &mon_bin_vm_ops;
+
+	if (vma->vm_flags & VM_WRITE)
+		return -EPERM;
+
+	vma->vm_flags &= ~VM_MAYWRITE;
 	vma->vm_flags |= VM_DONTEXPAND | VM_DONTDUMP;
 	vma->vm_private_data = filp->private_data;
 	mon_bin_vma_open(vma);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/mtu3/mtu3_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/mtu3/mtu3_core.c
@@ -971,8 +971,6 @@
 		goto irq_err;
 	}
 
-	device_init_wakeup(dev, true);
-
 	/* power down device IP for power saving by default */
 	mtu3_stop(mtu);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/mtu3/mtu3_dr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/mtu3/mtu3_dr.c
@@ -21,10 +21,8 @@
 
 static void toggle_opstate(struct ssusb_mtk *ssusb)
 {
-	if (!ssusb->otg_switch.is_u3_drd) {
-		mtu3_setbits(ssusb->mac_base, U3D_DEVICE_CONTROL, DC_SESSION);
-		mtu3_setbits(ssusb->mac_base, U3D_POWER_MANAGEMENT, SOFT_CONN);
-	}
+	mtu3_setbits(ssusb->mac_base, U3D_DEVICE_CONTROL, DC_SESSION);
+	mtu3_setbits(ssusb->mac_base, U3D_POWER_MANAGEMENT, SOFT_CONN);
 }
 
 /* only port0 supports dual-role mode */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/mtu3/mtu3_gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/mtu3/mtu3_gadget.c
@@ -77,7 +77,7 @@
 		if (usb_endpoint_xfer_int(desc) ||
 				usb_endpoint_xfer_isoc(desc)) {
 			interval = desc->bInterval;
-			interval = clamp_val(interval, 1, 16) - 1;
+			interval = clamp_val(interval, 1, 16);
 			if (usb_endpoint_xfer_isoc(desc) && comp_desc)
 				mult = comp_desc->bmAttributes;
 		}
@@ -89,10 +89,17 @@
 		if (usb_endpoint_xfer_isoc(desc) ||
 				usb_endpoint_xfer_int(desc)) {
 			interval = desc->bInterval;
-			interval = clamp_val(interval, 1, 16) - 1;
+			interval = clamp_val(interval, 1, 16);
 			mult = usb_endpoint_maxp_mult(desc) - 1;
 		}
 		break;
+	case USB_SPEED_FULL:
+		if (usb_endpoint_xfer_isoc(desc))
+			interval = clamp_val(desc->bInterval, 1, 16);
+		else if (usb_endpoint_xfer_int(desc))
+			interval = clamp_val(desc->bInterval, 1, 255);
+
+		break;
 	default:
 		break; /*others are ignored */
 	}
@@ -235,6 +242,7 @@
 	mreq->request.dma = DMA_ADDR_INVALID;
 	mreq->epnum = mep->epnum;
 	mreq->mep = mep;
+	INIT_LIST_HEAD(&mreq->list);
 	trace_mtu3_alloc_request(mreq);
 
 	return &mreq->request;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/mtu3/mtu3_plat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/mtu3/mtu3_plat.c
@@ -332,6 +332,8 @@
 	pm_runtime_enable(dev);
 	pm_runtime_get_sync(dev);
 
+	device_init_wakeup(dev, true);
+
 	ret = ssusb_rscs_init(ssusb);
 	if (ret)
 		goto comm_init_err;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/mtu3/mtu3_qmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/mtu3/mtu3_qmu.c
@@ -210,6 +210,7 @@
 	return ring->enqueue;
 }
 
+/* @dequeue may be NULL if ring is unallocated or freed */
 static struct qmu_gpd *advance_deq_gpd(struct mtu3_gpd_ring *ring)
 {
 	if (ring->dequeue < ring->end)
@@ -273,6 +274,8 @@
 			gpd->dw3_info |= cpu_to_le32(GPD_EXT_FLAG_ZLP);
 	}
 
+	/* prevent reorder, make sure GPD's HWO is set last */
+	mb();
 	gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_IOC | GPD_FLAGS_HWO);
 
 	mreq->gpd = gpd;
@@ -306,6 +309,8 @@
 	gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
 	ext_addr |= GPD_EXT_NGP(mtu, upper_32_bits(enq_dma));
 	gpd->dw3_info = cpu_to_le32(ext_addr);
+	/* prevent reorder, make sure GPD's HWO is set last */
+	mb();
 	gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_IOC | GPD_FLAGS_HWO);
 
 	mreq->gpd = gpd;
@@ -445,7 +450,8 @@
 		return;
 	}
 	mtu3_setbits(mbase, MU3D_EP_TXCR0(mep->epnum), TX_TXPKTRDY);
-
+	/* prevent reorder, make sure GPD's HWO is set last */
+	mb();
 	/* by pass the current GDP */
 	gpd_current->dw0_info |= cpu_to_le32(GPD_FLAGS_BPS | GPD_FLAGS_HWO);
 
@@ -479,7 +485,7 @@
 	dev_dbg(mtu->dev, "%s EP%d, last=%p, current=%p, enq=%p\n",
 		__func__, epnum, gpd, gpd_current, ring->enqueue);
 
-	while (gpd != gpd_current && !GET_GPD_HWO(gpd)) {
+	while (gpd && gpd != gpd_current && !GET_GPD_HWO(gpd)) {
 
 		mreq = next_request(mep);
 
@@ -518,7 +524,7 @@
 	dev_dbg(mtu->dev, "%s EP%d, last=%p, current=%p, enq=%p\n",
 		__func__, epnum, gpd, gpd_current, ring->enqueue);
 
-	while (gpd != gpd_current && !GET_GPD_HWO(gpd)) {
+	while (gpd && gpd != gpd_current && !GET_GPD_HWO(gpd)) {
 
 		mreq = next_request(mep);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/Kconfig
@@ -86,7 +86,7 @@
 	tristate "TUSB6010"
 	depends on HAS_IOMEM
 	depends on ARCH_OMAP2PLUS || COMPILE_TEST
-	depends on NOP_USB_XCEIV = USB_MUSB_HDRC # both built-in or both modules
+	depends on NOP_USB_XCEIV!=m || USB_MUSB_HDRC=m
 
 config USB_MUSB_OMAP2PLUS
 	tristate "OMAP2430 and onwards"
@@ -120,7 +120,7 @@
 	tristate "MediaTek platforms"
 	depends on ARCH_MEDIATEK || COMPILE_TEST
 	depends on NOP_USB_XCEIV
-	depends on GENERIC_PHY
+	select GENERIC_PHY
 	select USB_ROLE_SWITCH
 
 comment "MUSB DMA mode"
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/da8xx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/da8xx.c
@@ -556,7 +556,7 @@
 	ret = of_platform_populate(pdev->dev.of_node, NULL,
 				   da8xx_auxdata_lookup, &pdev->dev);
 	if (ret)
-		return ret;
+		goto err_unregister_phy;
 
 	memset(musb_resources, 0x00, sizeof(*musb_resources) *
 			ARRAY_SIZE(musb_resources));
@@ -582,9 +582,13 @@
 	ret = PTR_ERR_OR_ZERO(glue->musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device: %d\n", ret);
-		usb_phy_generic_unregister(glue->usb_phy);
+		goto err_unregister_phy;
 	}
 
+	return 0;
+
+err_unregister_phy:
+	usb_phy_generic_unregister(glue->usb_phy);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/mediatek.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/mediatek.c
@@ -346,7 +346,8 @@
 err_phy_power_on:
 	phy_exit(glue->phy);
 err_phy_init:
-	mtk_otg_switch_exit(glue);
+	if (musb->port_mode == MUSB_OTG)
+		mtk_otg_switch_exit(glue);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/musb_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/musb_debugfs.c
@@ -39,7 +39,7 @@
 	{ "IntrUsbE",	MUSB_INTRUSBE,	8 },
 	{ "DevCtl",	MUSB_DEVCTL,	8 },
 	{ "VControl",	0x68,		32 },
-	{ "HWVers",	0x69,		16 },
+	{ "HWVers",	MUSB_HWVERS,	16 },
 	{ "LinkInfo",	MUSB_LINKINFO,	8 },
 	{ "VPLen",	MUSB_VPLEN,	8 },
 	{ "HS_EOF1",	MUSB_HS_EOF1,	8 },
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/musb_gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/musb_gadget.c
@@ -760,6 +760,9 @@
 			musb_writew(epio, MUSB_RXCSR, csr);
 
 buffer_aint_mapped:
+			fifo_count = min_t(unsigned int,
+					request->length - request->actual,
+					(unsigned int)fifo_count);
 			musb_read_fifo(musb_ep->hw_ep, fifo_count, (u8 *)
 					(request->buf + request->actual));
 			request->actual += fifo_count;
@@ -1247,9 +1250,11 @@
 		status = musb_queue_resume_work(musb,
 						musb_ep_restart_resume_work,
 						request);
-		if (status < 0)
+		if (status < 0) {
 			dev_err(musb->controller, "%s resume work: %i\n",
 				__func__, status);
+			list_del(&request->list);
+		}
 	}
 
 unlock:
@@ -1623,8 +1628,6 @@
 {
 	struct musb	*musb = gadget_to_musb(gadget);
 
-	if (!musb->xceiv->set_power)
-		return -EOPNOTSUPP;
 	return usb_phy_set_power(musb->xceiv, mA);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/musb_host.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/musb_host.c
@@ -321,10 +321,16 @@
 	musb_giveback(musb, urb, status);
 	qh->is_ready = ready;
 
+	/*
+	 * musb->lock had been unlocked in musb_giveback, so qh may
+	 * be freed, need to get it again
+	 */
+	qh = musb_ep_get_qh(hw_ep, is_in);
+
 	/* reclaim resources (and bandwidth) ASAP; deschedule it, and
 	 * invalidate qh as soon as list_empty(&hep->urb_list)
 	 */
-	if (list_empty(&qh->hep->urb_list)) {
+	if (qh && list_empty(&qh->hep->urb_list)) {
 		struct list_head	*head;
 		struct dma_controller	*dma = musb->dma_controller;
 
@@ -2398,6 +2404,7 @@
 		 * and its URB list has emptied, recycle this qh.
 		 */
 		if (ready && list_empty(&qh->hep->urb_list)) {
+			musb_ep_set_qh(qh->hw_ep, is_in, NULL);
 			qh->hep->hcpriv = NULL;
 			list_del(&qh->ring);
 			kfree(qh);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/omap2430.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/omap2430.c
@@ -363,6 +363,7 @@
 	control_node = of_parse_phandle(np, "ctrl-module", 0);
 	if (control_node) {
 		control_pdev = of_find_device_by_node(control_node);
+		of_node_put(control_node);
 		if (!control_pdev) {
 			dev_err(&pdev->dev, "Failed to get control device\n");
 			ret = -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/sunxi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/sunxi.c
@@ -286,8 +286,6 @@
 	if (test_bit(SUNXI_MUSB_FL_HAS_SRAM, &glue->flags))
 		sunxi_sram_release(musb->controller->parent);
 
-	devm_usb_put_phy(glue->dev, glue->xceiv);
-
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/musb/tusb6010.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/musb/tusb6010.c
@@ -1104,6 +1104,11 @@
 
 	/* dma address for async dma */
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!mem) {
+		pr_debug("no async dma resource?\n");
+		ret = -ENODEV;
+		goto done;
+	}
 	musb->async = mem->start;
 
 	/* dma address for sync dma */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/phy/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/phy/Kconfig
@@ -173,6 +173,7 @@
 config USB_ULPI
 	bool "Generic ULPI Transceiver Driver"
 	depends on ARM || ARM64 || COMPILE_TEST
+	depends on USB_PHY
 	select USB_ULPI_VIEWPORT
 	help
 	  Enable this to support ULPI connected USB OTG transceivers which
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/phy/phy-mxs-usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/phy/phy-mxs-usb.c
@@ -388,14 +388,7 @@
 
 static bool mxs_phy_is_otg_host(struct mxs_phy *mxs_phy)
 {
-	void __iomem *base = mxs_phy->phy.io_priv;
-	u32 phyctrl = readl(base + HW_USBPHY_CTRL);
-
-	if (IS_ENABLED(CONFIG_USB_OTG) &&
-			!(phyctrl & BM_USBPHY_CTRL_OTG_ID_VALUE))
-		return true;
-
-	return false;
+	return mxs_phy->phy.last_event == USB_EVENT_ID;
 }
 
 static void mxs_phy_disconnect_line(struct mxs_phy *mxs_phy, bool on)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/phy/phy-omap-otg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/phy/phy-omap-otg.c
@@ -95,8 +95,8 @@
 		return -ENODEV;
 
 	extcon = extcon_get_extcon_dev(config->extcon);
-	if (!extcon)
-		return -EPROBE_DEFER;
+	if (IS_ERR(extcon))
+		return PTR_ERR(extcon);
 
 	otg_dev = devm_kzalloc(&pdev->dev, sizeof(*otg_dev), GFP_KERNEL);
 	if (!otg_dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/phy/phy-tahvo.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/phy/phy-tahvo.c
@@ -395,7 +395,7 @@
 
 	tu->irq = ret = platform_get_irq(pdev, 0);
 	if (ret < 0)
-		return ret;
+		goto err_remove_phy;
 	ret = request_threaded_irq(tu->irq, NULL, tahvo_usb_vbus_interrupt,
 				   IRQF_ONESHOT,
 				   "tahvo-vbus", tu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/phy/phy-ulpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/phy/phy-ulpi.c
@@ -13,9 +13,16 @@
 #include <linux/kernel.h>
 #include <linux/slab.h>
 #include <linux/export.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
 #include <linux/usb.h>
 #include <linux/usb/otg.h>
 #include <linux/usb/ulpi.h>
+#include <linux/usb/phy.h>
 
 
 struct ulpi_info {
@@ -39,6 +46,13 @@
 	ULPI_INFO(ULPI_ID(0x0451, 0x1507), "TI TUSB1210"),
 };
 
+struct ulpi_phy {
+	struct usb_phy	*usb_phy;
+	void __iomem *regs;
+	unsigned int vp_offset;
+	unsigned int flags;
+};
+
 static int ulpi_set_otg_flags(struct usb_phy *phy)
 {
 	unsigned int flags = ULPI_OTG_CTRL_DP_PULLDOWN |
@@ -240,6 +254,23 @@
 	return usb_phy_io_write(phy, flags, ULPI_OTG_CTRL);
 }
 
+static int usbphy_set_vbus(struct usb_phy *phy, int on)
+{
+	unsigned int flags = usb_phy_io_read(phy, ULPI_OTG_CTRL);
+
+	flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT);
+
+	if (on) {
+		if (phy->flags & ULPI_OTG_DRVVBUS)
+			flags |= ULPI_OTG_CTRL_DRVVBUS;
+
+		if (phy->flags & ULPI_OTG_DRVVBUS_EXT)
+			flags |= ULPI_OTG_CTRL_DRVVBUS_EXT;
+	}
+
+	return usb_phy_io_write(phy, flags, ULPI_OTG_CTRL);
+}
+
 static void otg_ulpi_init(struct usb_phy *phy, struct usb_otg *otg,
 			  struct usb_phy_io_ops *ops,
 			  unsigned int flags)
@@ -249,6 +280,7 @@
 	phy->io_ops	= ops;
 	phy->otg	= otg;
 	phy->init	= ulpi_init;
+	phy->set_vbus	= usbphy_set_vbus;
 
 	otg->usb_phy	= phy;
 	otg->set_host	= ulpi_set_host;
@@ -301,3 +333,83 @@
 	return phy;
 }
 EXPORT_SYMBOL_GPL(devm_otg_ulpi_create);
+
+static int ulpi_phy_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct resource *res;
+	struct ulpi_phy *uphy;
+	bool flag;
+	int ret;
+
+	uphy = devm_kzalloc(&pdev->dev, sizeof(*uphy), GFP_KERNEL);
+	if (!uphy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "no phy I/O memory resource defined\n");
+		return -ENODEV;
+	}
+
+	uphy->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+	if (!uphy->regs) {
+		dev_err(&pdev->dev, "failed to map phy I/O memory\n");
+		return -EFAULT;
+	}
+
+	if (IS_ERR(uphy->regs))
+		return PTR_ERR(uphy->regs);
+
+	if (of_property_read_u32(np, "view-port", &uphy->vp_offset))
+		dev_dbg(&pdev->dev, "Missing view-port property\n");
+
+	if (IS_ERR(uphy->regs)) {
+		dev_err(&pdev->dev, "view-port register not specified\n");
+		return PTR_ERR(uphy->regs);
+	}
+
+	flag = of_property_read_bool(np, "drv-vbus");
+	if (flag)
+		uphy->flags |= ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT;
+
+	uphy->usb_phy = otg_ulpi_create(&ulpi_viewport_access_ops, uphy->flags);
+
+	uphy->usb_phy->dev = &pdev->dev;
+
+	uphy->usb_phy->io_priv = uphy->regs + uphy->vp_offset;
+
+	ret = usb_add_phy_dev(uphy->usb_phy);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int ulpi_phy_remove(struct platform_device *pdev)
+{
+	struct ulpi_phy *uphy = platform_get_drvdata(pdev);
+
+	usb_remove_phy(uphy->usb_phy);
+
+	return 0;
+}
+
+static const struct of_device_id ulpi_phy_table[] = {
+	{ .compatible = "ulpi-phy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ulpi_phy_table);
+
+static struct platform_driver ulpi_phy_driver = {
+	.probe		= ulpi_phy_probe,
+	.remove		= ulpi_phy_remove,
+	.driver		= {
+		.name	= "ulpi-phy",
+		.of_match_table = ulpi_phy_table,
+	},
+};
+module_platform_driver(ulpi_phy_driver);
+
+MODULE_DESCRIPTION("ULPI PHY driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/phy/phy.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/phy/phy.c
@@ -628,7 +628,7 @@
 {
 	int r;
 
-	r = devres_destroy(dev, devm_usb_phy_release, devm_usb_phy_match, phy);
+	r = devres_release(dev, devm_usb_phy_release, devm_usb_phy_match, phy);
 	dev_WARN_ONCE(dev, r, "couldn't find PHY resource\n");
 }
 EXPORT_SYMBOL_GPL(devm_usb_put_phy);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/renesas_usbhs/common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/renesas_usbhs/common.c
@@ -312,8 +312,10 @@
 	priv->clks[1] = of_clk_get(dev_of_node(dev), 1);
 	if (PTR_ERR(priv->clks[1]) == -ENOENT)
 		priv->clks[1] = NULL;
-	else if (IS_ERR(priv->clks[1]))
+	else if (IS_ERR(priv->clks[1])) {
+		clk_put(priv->clks[0]);
 		return PTR_ERR(priv->clks[1]);
+	}
 
 	return 0;
 }
@@ -772,6 +774,8 @@
 
 	dev_dbg(&pdev->dev, "usb remove\n");
 
+	flush_delayed_work(&priv->notify_hotplug_work);
+
 	/* power off */
 	if (!usbhs_get_dparam(priv, runtime_pwctrl))
 		usbhsc_power_ctrl(priv, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/renesas_usbhs/mod_gadget.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/renesas_usbhs/mod_gadget.c
@@ -1094,7 +1094,7 @@
 		goto usbhs_mod_gadget_probe_err_gpriv;
 	}
 
-	gpriv->transceiver = usb_get_phy(USB_PHY_TYPE_UNDEFINED);
+	gpriv->transceiver = devm_usb_get_phy(dev, USB_PHY_TYPE_UNDEFINED);
 	dev_info(dev, "%stransceiver found\n",
 		 !IS_ERR(gpriv->transceiver) ? "" : "no ");
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/renesas_usbhs/rza.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/renesas_usbhs/rza.c
@@ -23,6 +23,10 @@
 	extal_clk = of_find_node_by_name(NULL, "extal");
 	of_property_read_u32(usb_x1_clk, "clock-frequency", &freq_usb);
 	of_property_read_u32(extal_clk, "clock-frequency", &freq_extal);
+
+	of_node_put(usb_x1_clk);
+	of_node_put(extal_clk);
+
 	if (freq_usb == 0) {
 		if (freq_extal == 12000000) {
 			/* Select 12MHz XTAL */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/roles/class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/roles/class.c
@@ -19,7 +19,9 @@
 struct usb_role_switch {
 	struct device dev;
 	struct mutex lock; /* device lock*/
+	struct module *module; /* the module this device depends on */
 	enum usb_role role;
+	bool registered;
 
 	/* From descriptor */
 	struct device *usb2_port;
@@ -46,6 +48,9 @@
 	if (IS_ERR_OR_NULL(sw))
 		return 0;
 
+	if (!sw->registered)
+		return -EOPNOTSUPP;
+
 	mutex_lock(&sw->lock);
 
 	ret = sw->set(sw, role);
@@ -71,7 +76,7 @@
 {
 	enum usb_role role;
 
-	if (IS_ERR_OR_NULL(sw))
+	if (IS_ERR_OR_NULL(sw) || !sw->registered)
 		return USB_ROLE_NONE;
 
 	mutex_lock(&sw->lock);
@@ -106,10 +111,13 @@
 	struct fwnode_handle *parent = fwnode_get_parent(fwnode);
 	struct device *dev;
 
-	if (!parent || !fwnode_property_present(parent, "usb-role-switch"))
+	if (!fwnode_property_present(parent, "usb-role-switch")) {
+		fwnode_handle_put(parent);
 		return NULL;
+	}
 
 	dev = class_find_device_by_fwnode(role_class, parent);
+	fwnode_handle_put(parent);
 	return dev ? to_role_switch(dev) : ERR_PTR(-EPROBE_DEFER);
 }
 
@@ -130,7 +138,7 @@
 						  usb_role_switch_match);
 
 	if (!IS_ERR_OR_NULL(sw))
-		WARN_ON(!try_module_get(sw->dev.parent->driver->owner));
+		WARN_ON(!try_module_get(sw->module));
 
 	return sw;
 }
@@ -152,7 +160,7 @@
 		sw = fwnode_connection_find_match(fwnode, "usb-role-switch",
 						  NULL, usb_role_switch_match);
 	if (!IS_ERR_OR_NULL(sw))
-		WARN_ON(!try_module_get(sw->dev.parent->driver->owner));
+		WARN_ON(!try_module_get(sw->module));
 
 	return sw;
 }
@@ -167,7 +175,7 @@
 void usb_role_switch_put(struct usb_role_switch *sw)
 {
 	if (!IS_ERR_OR_NULL(sw)) {
-		module_put(sw->dev.parent->driver->owner);
+		module_put(sw->module);
 		put_device(&sw->dev);
 	}
 }
@@ -184,15 +192,18 @@
 usb_role_switch_find_by_fwnode(const struct fwnode_handle *fwnode)
 {
 	struct device *dev;
+	struct usb_role_switch *sw = NULL;
 
 	if (!fwnode)
 		return NULL;
 
 	dev = class_find_device_by_fwnode(role_class, fwnode);
-	if (dev)
-		WARN_ON(!try_module_get(dev->parent->driver->owner));
+	if (dev) {
+		sw = to_role_switch(dev);
+		WARN_ON(!try_module_get(sw->module));
+	}
 
-	return dev ? to_role_switch(dev) : NULL;
+	return sw;
 }
 EXPORT_SYMBOL_GPL(usb_role_switch_find_by_fwnode);
 
@@ -334,6 +345,7 @@
 	sw->set = desc->set;
 	sw->get = desc->get;
 
+	sw->module = parent->driver->owner;
 	sw->dev.parent = parent;
 	sw->dev.fwnode = desc->fwnode;
 	sw->dev.class = role_class;
@@ -342,8 +354,11 @@
 	dev_set_name(&sw->dev, "%s-role-switch",
 		     desc->name ? desc->name : dev_name(parent));
 
+	sw->registered = true;
+
 	ret = device_register(&sw->dev);
 	if (ret) {
+		sw->registered = false;
 		put_device(&sw->dev);
 		return ERR_PTR(ret);
 	}
@@ -362,8 +377,10 @@
  */
 void usb_role_switch_unregister(struct usb_role_switch *sw)
 {
-	if (!IS_ERR_OR_NULL(sw))
+	if (!IS_ERR_OR_NULL(sw)) {
+		sw->registered = false;
 		device_unregister(&sw->dev);
+	}
 }
 EXPORT_SYMBOL_GPL(usb_role_switch_unregister);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/Kconfig
@@ -66,6 +66,7 @@
 		- Libtransistor USB console
 		- a number of Motorola phones
 		- Motorola Tetra devices
+		- Nokia mobile phones
 		- Novatel Wireless GPS receivers
 		- Siemens USB/MPI adapter.
 		- ViVOtech ViVOpay USB device.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/ch341.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/ch341.c
@@ -81,10 +81,10 @@
 #define CH341_QUIRK_SIMULATE_BREAK	BIT(1)
 
 static const struct usb_device_id id_table[] = {
-	{ USB_DEVICE(0x1a86, 0x5512) },
 	{ USB_DEVICE(0x1a86, 0x5523) },
 	{ USB_DEVICE(0x1a86, 0x7522) },
 	{ USB_DEVICE(0x1a86, 0x7523) },
+	{ USB_DEVICE(0x2184, 0x0057) },
 	{ USB_DEVICE(0x4348, 0x5523) },
 	{ USB_DEVICE(0x9986, 0x7523) },
 	{ },
@@ -97,7 +97,10 @@
 	u8 mcr;
 	u8 msr;
 	u8 lcr;
+
 	unsigned long quirks;
+	u8 version;
+
 	unsigned long break_end;
 };
 
@@ -256,8 +259,12 @@
 	/*
 	 * CH341A buffers data until a full endpoint-size packet (32 bytes)
 	 * has been received unless bit 7 is set.
+	 *
+	 * At least one device with version 0x27 appears to have this bit
+	 * inverted.
 	 */
-	val |= BIT(7);
+	if (priv->version > 0x27)
+		val |= BIT(7);
 
 	r = ch341_control_out(dev, CH341_REQ_WRITE_REG,
 			      CH341_REG_DIVISOR << 8 | CH341_REG_PRESCALER,
@@ -271,6 +278,9 @@
 	 * (stop bits, parity and word length). Version 0x30 and above use
 	 * CH341_REG_LCR only and CH341_REG_LCR2 is always set to zero.
 	 */
+	if (priv->version < 0x30)
+		return 0;
+
 	r = ch341_control_out(dev, CH341_REQ_WRITE_REG,
 			      CH341_REG_LCR2 << 8 | CH341_REG_LCR, lcr);
 	if (r)
@@ -323,7 +333,9 @@
 	r = ch341_control_in(dev, CH341_REQ_READ_VERSION, 0, 0, buffer, size);
 	if (r < 0)
 		goto out;
-	dev_dbg(&dev->dev, "Chip version: 0x%02x\n", buffer[0]);
+
+	priv->version = buffer[0];
+	dev_dbg(&dev->dev, "Chip version: 0x%02x\n", priv->version);
 
 	r = ch341_control_out(dev, CH341_REQ_SERIAL_INIT, 0, 0);
 	if (r < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/cp210x.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/cp210x.c
@@ -51,14 +51,18 @@
 static void cp210x_disable_event_mode(struct usb_serial_port *port);
 
 static const struct usb_device_id id_table[] = {
+	{ USB_DEVICE(0x0404, 0x034C) },	/* NCR Retail IO Box */
 	{ USB_DEVICE(0x045B, 0x0053) }, /* Renesas RX610 RX-Stick */
 	{ USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
 	{ USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
 	{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
+	{ USB_DEVICE(0x04BF, 0x1301) }, /* TDK Corporation NC0110013M - Network Controller */
+	{ USB_DEVICE(0x04BF, 0x1303) }, /* TDK Corporation MM0110113M - i3 Micro Module */
 	{ USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
 	{ USB_DEVICE(0x0846, 0x1100) }, /* NetGear Managed Switch M4100 series, M5300 series, M7100 series */
 	{ USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
 	{ USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
+	{ USB_DEVICE(0x0908, 0x0070) }, /* Siemens SCALANCE LPE-9000 USB Serial Console */
 	{ USB_DEVICE(0x0908, 0x01FF) }, /* Siemens RUGGEDCOM USB Serial Console */
 	{ USB_DEVICE(0x0988, 0x0578) }, /* Teraoka AD2000 */
 	{ USB_DEVICE(0x0B00, 0x3070) }, /* Ingenico 3070 */
@@ -68,6 +72,7 @@
 	{ USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
 	{ USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
 	{ USB_DEVICE(0x0FDE, 0xCA05) }, /* OWL Wireless Electricity Monitor CM-160 */
+	{ USB_DEVICE(0x106F, 0x0003) },	/* CPI / Money Controls Bulk Coin Recycler */
 	{ USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
 	{ USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
 	{ USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
@@ -117,6 +122,7 @@
 	{ USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */
 	{ USB_DEVICE(0x10C4, 0x8281) }, /* Nanotec Plug & Drive */
 	{ USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */
+	{ USB_DEVICE(0x10C4, 0x82AA) }, /* Silicon Labs IFS-USB-DATACABLE used with Quint UPS */
 	{ USB_DEVICE(0x10C4, 0x82EF) }, /* CESINEL FALCO 6105 AC Power Supply */
 	{ USB_DEVICE(0x10C4, 0x82F1) }, /* CESINEL MEDCAL EFD Earth Fault Detector */
 	{ USB_DEVICE(0x10C4, 0x82F2) }, /* CESINEL MEDCAL ST Network Analyzer */
@@ -128,6 +134,7 @@
 	{ USB_DEVICE(0x10C4, 0x83AA) }, /* Mark-10 Digital Force Gauge */
 	{ USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
 	{ USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
+	{ USB_DEVICE(0x10C4, 0x8414) }, /* Decagon USB Cable Adapter */
 	{ USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */
 	{ USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
 	{ USB_DEVICE(0x10C4, 0x8470) }, /* Juniper Networks BX Series System Console */
@@ -139,8 +146,10 @@
 	{ USB_DEVICE(0x10C4, 0x85EA) }, /* AC-Services IBUS-IF */
 	{ USB_DEVICE(0x10C4, 0x85EB) }, /* AC-Services CIS-IBUS */
 	{ USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */
+	{ USB_DEVICE(0x10C4, 0x863C) }, /* MGP Instruments PDS100 */
 	{ USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
 	{ USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
+	{ USB_DEVICE(0x10C4, 0x87ED) }, /* IMST USB-Stick for Smart Meter */
 	{ USB_DEVICE(0x10C4, 0x8856) },	/* CEL EM357 ZigBee USB Stick - LR */
 	{ USB_DEVICE(0x10C4, 0x8857) },	/* CEL EM357 ZigBee USB Stick */
 	{ USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
@@ -171,6 +180,7 @@
 	{ USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
 	{ USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
 	{ USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
+	{ USB_DEVICE(0x11CA, 0x0212) }, /* Verifone USB to Printer (UART, CP2102) */
 	{ USB_DEVICE(0x12B8, 0xEC60) }, /* Link G4 ECU */
 	{ USB_DEVICE(0x12B8, 0xEC62) }, /* Link G4+ ECU */
 	{ USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
@@ -192,6 +202,10 @@
 	{ USB_DEVICE(0x16DC, 0x0015) }, /* W-IE-NE-R Plein & Baus GmbH CML Control, Monitoring and Data Logger */
 	{ USB_DEVICE(0x17A8, 0x0001) }, /* Kamstrup Optical Eye/3-wire */
 	{ USB_DEVICE(0x17A8, 0x0005) }, /* Kamstrup M-Bus Master MultiPort 250D */
+	{ USB_DEVICE(0x17A8, 0x0011) }, /* Kamstrup 444 MHz RF sniffer */
+	{ USB_DEVICE(0x17A8, 0x0013) }, /* Kamstrup 870 MHz RF sniffer */
+	{ USB_DEVICE(0x17A8, 0x0101) }, /* Kamstrup 868 MHz wM-Bus C-Mode Meter Reader (Int Ant) */
+	{ USB_DEVICE(0x17A8, 0x0102) }, /* Kamstrup 868 MHz wM-Bus C-Mode Meter Reader (Ext Ant) */
 	{ USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
 	{ USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
 	{ USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
@@ -209,6 +223,7 @@
 	{ USB_DEVICE(0x19CF, 0x3000) }, /* Parrot NMEA GPS Flight Recorder */
 	{ USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */
 	{ USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */
+	{ USB_DEVICE(0x1B93, 0x1013) }, /* Phoenix Contact UPS Device */
 	{ USB_DEVICE(0x1BA4, 0x0002) },	/* Silicon Labs 358x factory default */
 	{ USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
 	{ USB_DEVICE(0x1D6F, 0x0010) }, /* Seluxit ApS RF Dongle */
@@ -1682,6 +1697,8 @@
 
 	/*  2 banks of GPIO - One for the pins taken from each serial port */
 	if (intf_num == 0) {
+		priv->gc.ngpio = 2;
+
 		if (mode.eci == CP210X_PIN_MODE_MODEM) {
 			/* mark all GPIOs of this interface as reserved */
 			priv->gpio_altfunc = 0xff;
@@ -1692,8 +1709,9 @@
 		priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
 						CP210X_ECI_GPIO_MODE_MASK) >>
 						CP210X_ECI_GPIO_MODE_OFFSET);
-		priv->gc.ngpio = 2;
 	} else if (intf_num == 1) {
+		priv->gc.ngpio = 3;
+
 		if (mode.sci == CP210X_PIN_MODE_MODEM) {
 			/* mark all GPIOs of this interface as reserved */
 			priv->gpio_altfunc = 0xff;
@@ -1704,7 +1722,6 @@
 		priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
 						CP210X_SCI_GPIO_MODE_MASK) >>
 						CP210X_SCI_GPIO_MODE_OFFSET);
-		priv->gc.ngpio = 3;
 	} else {
 		return -ENODEV;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/f81232.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/f81232.c
@@ -130,9 +130,6 @@
 
 static int calc_baud_divisor(speed_t baudrate, speed_t clockrate)
 {
-	if (!baudrate)
-		return 0;
-
 	return DIV_ROUND_CLOSEST(clockrate, baudrate);
 }
 
@@ -519,9 +516,14 @@
 	speed_t baud_list[] = { baudrate, old_baudrate, F81232_DEF_BAUDRATE };
 
 	for (i = 0; i < ARRAY_SIZE(baud_list); ++i) {
-		idx = f81232_find_clk(baud_list[i]);
+		baudrate = baud_list[i];
+		if (baudrate == 0) {
+			tty_encode_baud_rate(tty, 0, 0);
+			return;
+		}
+
+		idx = f81232_find_clk(baudrate);
 		if (idx >= 0) {
-			baudrate = baud_list[i];
 			tty_encode_baud_rate(tty, baudrate, baudrate);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/f81534.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/f81534.c
@@ -536,9 +536,6 @@
 
 static u32 f81534_calc_baud_divisor(u32 baudrate, u32 clockrate)
 {
-	if (!baudrate)
-		return 0;
-
 	/* Round to nearest divisor */
 	return DIV_ROUND_CLOSEST(clockrate, baudrate);
 }
@@ -568,9 +565,14 @@
 	u32 baud_list[] = {baudrate, old_baudrate, F81534_DEFAULT_BAUD_RATE};
 
 	for (i = 0; i < ARRAY_SIZE(baud_list); ++i) {
-		idx = f81534_find_clk(baud_list[i]);
+		baudrate = baud_list[i];
+		if (baudrate == 0) {
+			tty_encode_baud_rate(tty, 0, 0);
+			return 0;
+		}
+
+		idx = f81534_find_clk(baudrate);
 		if (idx >= 0) {
-			baudrate = baud_list[i];
 			tty_encode_baud_rate(tty, baudrate, baudrate);
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/ftdi_sio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/ftdi_sio.c
@@ -969,6 +969,7 @@
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_VX_023_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_VX_034_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_101_PID) },
+	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_159_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_1_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_2_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_3_PID) },
@@ -977,12 +978,14 @@
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_6_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_7_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_8_PID) },
+	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_235_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_257_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_1_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_2_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_3_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_4_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_313_PID) },
+	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_320_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_324_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_346_1_PID) },
 	{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_346_2_PID) },
@@ -1008,9 +1011,9 @@
 	{ USB_DEVICE(FTDI_VID, ACTISENSE_USG_PID) },
 	{ USB_DEVICE(FTDI_VID, ACTISENSE_NGT_PID) },
 	{ USB_DEVICE(FTDI_VID, ACTISENSE_NGW_PID) },
-	{ USB_DEVICE(FTDI_VID, ACTISENSE_D9AC_PID) },
-	{ USB_DEVICE(FTDI_VID, ACTISENSE_D9AD_PID) },
-	{ USB_DEVICE(FTDI_VID, ACTISENSE_D9AE_PID) },
+	{ USB_DEVICE(FTDI_VID, ACTISENSE_UID_PID) },
+	{ USB_DEVICE(FTDI_VID, ACTISENSE_USA_PID) },
+	{ USB_DEVICE(FTDI_VID, ACTISENSE_NGX_PID) },
 	{ USB_DEVICE(FTDI_VID, ACTISENSE_D9AF_PID) },
 	{ USB_DEVICE(FTDI_VID, CHETCO_SEAGAUGE_PID) },
 	{ USB_DEVICE(FTDI_VID, CHETCO_SEASWITCH_PID) },
@@ -1020,6 +1023,9 @@
 	{ USB_DEVICE(FTDI_VID, CHETCO_SEASMART_DISPLAY_PID) },
 	{ USB_DEVICE(FTDI_VID, CHETCO_SEASMART_LITE_PID) },
 	{ USB_DEVICE(FTDI_VID, CHETCO_SEASMART_ANALOG_PID) },
+	/* Belimo Automation devices */
+	{ USB_DEVICE(FTDI_VID, BELIMO_ZTH_PID) },
+	{ USB_DEVICE(FTDI_VID, BELIMO_ZIP_PID) },
 	/* ICP DAS I-756xU devices */
 	{ USB_DEVICE(ICPDAS_VID, ICPDAS_I7560U_PID) },
 	{ USB_DEVICE(ICPDAS_VID, ICPDAS_I7561U_PID) },
@@ -1039,6 +1045,8 @@
 	/* IDS GmbH devices */
 	{ USB_DEVICE(IDS_VID, IDS_SI31A_PID) },
 	{ USB_DEVICE(IDS_VID, IDS_CM31A_PID) },
+	/* Omron devices */
+	{ USB_DEVICE(OMRON_VID, OMRON_CS1W_CIF31_PID) },
 	/* U-Blox devices */
 	{ USB_DEVICE(UBLOX_VID, UBLOX_C099F9P_ZED_PID) },
 	{ USB_DEVICE(UBLOX_VID, UBLOX_C099F9P_ODIN_PID) },
@@ -1047,6 +1055,22 @@
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(FTDI_VID, FTDI_FALCONIA_JTAG_UNBUF_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+	/* GMC devices */
+	{ USB_DEVICE(GMC_VID, GMC_Z216C_PID) },
+	/* Altera USB Blaster 3 */
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6022_PID, 1) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6025_PID, 2) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6026_PID, 2) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6026_PID, 3) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6029_PID, 2) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602A_PID, 2) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602A_PID, 3) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602C_PID, 1) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602D_PID, 1) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602D_PID, 2) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602E_PID, 1) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602E_PID, 2) },
+	{ USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602E_PID, 3) },
 	{ }					/* Terminating entry */
 };
 
@@ -1311,8 +1335,7 @@
 		case 38400: div_value = ftdi_sio_b38400; break;
 		case 57600: div_value = ftdi_sio_b57600;  break;
 		case 115200: div_value = ftdi_sio_b115200; break;
-		} /* baud */
-		if (div_value == 0) {
+		default:
 			dev_dbg(dev, "%s - Baudrate (%d) requested is not supported\n",
 				__func__,  baud);
 			div_value = ftdi_sio_b9600;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/ftdi_sio_ids.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/ftdi_sio_ids.h
@@ -662,6 +662,12 @@
 #define INFINEON_TRIBOARD_TC2X7_PID	0x0043 /* DAS JTAG TriBoard TC2X7 V1.0 */
 
 /*
+ * Omron corporation (https://www.omron.com)
+ */
+ #define OMRON_VID			0x0590
+ #define OMRON_CS1W_CIF31_PID		0x00b2
+
+/*
  * Acton Research Corp.
  */
 #define ACTON_VID		0x0647	/* Vendor ID */
@@ -1506,6 +1512,9 @@
 #define BRAINBOXES_VX_023_PID		0x1003 /* VX-023 ExpressCard 1 Port RS422/485 */
 #define BRAINBOXES_VX_034_PID		0x1004 /* VX-034 ExpressCard 2 Port RS422/485 */
 #define BRAINBOXES_US_101_PID		0x1011 /* US-101 1xRS232 */
+#define BRAINBOXES_US_159_PID		0x1021 /* US-159 1xRS232 */
+#define BRAINBOXES_US_235_PID		0x1017 /* US-235 1xRS232 */
+#define BRAINBOXES_US_320_PID		0x1019 /* US-320 1xRS422/485 */
 #define BRAINBOXES_US_324_PID		0x1013 /* US-324 1xRS422/485 1Mbaud */
 #define BRAINBOXES_US_606_1_PID		0x2001 /* US-606 6 Port RS232 Serial Port 1 and 2 */
 #define BRAINBOXES_US_606_2_PID		0x2002 /* US-606 6 Port RS232 Serial Port 3 and 4 */
@@ -1552,9 +1561,9 @@
 #define ACTISENSE_USG_PID		0xD9A9 /* USG USB Serial Adapter */
 #define ACTISENSE_NGT_PID		0xD9AA /* NGT NMEA2000 Interface */
 #define ACTISENSE_NGW_PID		0xD9AB /* NGW NMEA2000 Gateway */
-#define ACTISENSE_D9AC_PID		0xD9AC /* Actisense Reserved */
-#define ACTISENSE_D9AD_PID		0xD9AD /* Actisense Reserved */
-#define ACTISENSE_D9AE_PID		0xD9AE /* Actisense Reserved */
+#define ACTISENSE_UID_PID		0xD9AC /* USB Isolating Device */
+#define ACTISENSE_USA_PID		0xD9AD /* USB to Serial Adapter */
+#define ACTISENSE_NGX_PID		0xD9AE /* NGX NMEA2000 Gateway */
 #define ACTISENSE_D9AF_PID		0xD9AF /* Actisense Reserved */
 #define CHETCO_SEAGAUGE_PID		0xA548 /* SeaGauge USB Adapter */
 #define CHETCO_SEASWITCH_PID		0xA549 /* SeaSwitch USB Adapter */
@@ -1566,6 +1575,12 @@
 #define CHETCO_SEASMART_ANALOG_PID	0xA5AF /* SeaSmart Analog Adapter */
 
 /*
+ * Belimo Automation
+ */
+#define BELIMO_ZTH_PID			0x8050
+#define BELIMO_ZIP_PID			0xC811
+
+/*
  * Unjo AB
  */
 #define UNJO_VID			0x22B7
@@ -1584,3 +1599,22 @@
 #define UBLOX_VID			0x1546
 #define UBLOX_C099F9P_ZED_PID		0x0502
 #define UBLOX_C099F9P_ODIN_PID		0x0503
+
+/*
+ * GMC devices
+ */
+#define GMC_VID				0x1cd7
+#define GMC_Z216C_PID			0x0217 /* GMC Z216C Adapter IR-USB */
+
+/*
+ *  Altera USB Blaster 3 (http://www.altera.com).
+ */
+#define ALTERA_VID			0x09fb
+#define ALTERA_UB3_6022_PID		0x6022
+#define ALTERA_UB3_6025_PID		0x6025
+#define ALTERA_UB3_6026_PID		0x6026
+#define ALTERA_UB3_6029_PID		0x6029
+#define ALTERA_UB3_602A_PID		0x602a
+#define ALTERA_UB3_602C_PID		0x602c
+#define ALTERA_UB3_602D_PID		0x602d
+#define ALTERA_UB3_602E_PID		0x602e
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/io_edgeport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/io_edgeport.c
@@ -770,11 +770,12 @@
 static void edge_bulk_out_cmd_callback(struct urb *urb)
 {
 	struct edgeport_port *edge_port = urb->context;
+	struct device *dev = &urb->dev->dev;
 	int status = urb->status;
 
 	atomic_dec(&CmdUrbs);
-	dev_dbg(&urb->dev->dev, "%s - FREE URB %p (outstanding %d)\n",
-		__func__, urb, atomic_read(&CmdUrbs));
+	dev_dbg(dev, "%s - FREE URB %p (outstanding %d)\n", __func__, urb,
+		atomic_read(&CmdUrbs));
 
 
 	/* clean up the transfer buffer */
@@ -784,8 +785,7 @@
 	usb_free_urb(urb);
 
 	if (status) {
-		dev_dbg(&urb->dev->dev,
-			"%s - nonzero write bulk status received: %d\n",
+		dev_dbg(dev, "%s - nonzero write bulk status received: %d\n",
 			__func__, status);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/io_ti.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/io_ti.c
@@ -166,6 +166,7 @@
 	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) },
 	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) },
 	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) },
+	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_E5805A) },
 	{ }
 };
 
@@ -204,6 +205,7 @@
 	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) },
 	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) },
 	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) },
+	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_E5805A) },
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/io_usbvend.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/io_usbvend.h
@@ -212,6 +212,7 @@
 //
 // Definitions for other product IDs
 #define ION_DEVICE_ID_MT4X56USB			0x1403	// OEM device
+#define ION_DEVICE_ID_E5805A			0x1A01  // OEM device (rebranded Edgeport/4)
 
 
 #define	GENERATION_ID_FROM_USB_PRODUCT_ID(ProductId)				\
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/keyspan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/keyspan.c
@@ -2890,22 +2890,22 @@
 	for (i = 0; i < ARRAY_SIZE(p_priv->in_buffer); ++i) {
 		p_priv->in_buffer[i] = kzalloc(IN_BUFLEN, GFP_KERNEL);
 		if (!p_priv->in_buffer[i])
-			goto err_in_buffer;
+			goto err_free_in_buffer;
 	}
 
 	for (i = 0; i < ARRAY_SIZE(p_priv->out_buffer); ++i) {
 		p_priv->out_buffer[i] = kzalloc(OUT_BUFLEN, GFP_KERNEL);
 		if (!p_priv->out_buffer[i])
-			goto err_out_buffer;
+			goto err_free_out_buffer;
 	}
 
 	p_priv->inack_buffer = kzalloc(INACK_BUFLEN, GFP_KERNEL);
 	if (!p_priv->inack_buffer)
-		goto err_inack_buffer;
+		goto err_free_out_buffer;
 
 	p_priv->outcont_buffer = kzalloc(OUTCONT_BUFLEN, GFP_KERNEL);
 	if (!p_priv->outcont_buffer)
-		goto err_outcont_buffer;
+		goto err_free_inack_buffer;
 
 	p_priv->device_details = d_details;
 
@@ -2951,15 +2951,14 @@
 
 	return 0;
 
-err_outcont_buffer:
+err_free_inack_buffer:
 	kfree(p_priv->inack_buffer);
-err_inack_buffer:
+err_free_out_buffer:
 	for (i = 0; i < ARRAY_SIZE(p_priv->out_buffer); ++i)
 		kfree(p_priv->out_buffer[i]);
-err_out_buffer:
+err_free_in_buffer:
 	for (i = 0; i < ARRAY_SIZE(p_priv->in_buffer); ++i)
 		kfree(p_priv->in_buffer[i]);
-err_in_buffer:
 	kfree(p_priv);
 
 	return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/mos7840.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/mos7840.c
@@ -1735,6 +1735,49 @@
 	kfree(mos7840_port);
 }
 
+static int mos7840_suspend(struct usb_serial *serial, pm_message_t message)
+{
+	struct moschip_port *mos7840_port;
+	struct usb_serial_port *port;
+	int i;
+
+	for (i = 0; i < serial->num_ports; ++i) {
+		port = serial->port[i];
+		if (!tty_port_initialized(&port->port))
+			continue;
+
+		mos7840_port = usb_get_serial_port_data(port);
+
+		usb_kill_urb(mos7840_port->read_urb);
+		mos7840_port->read_urb_busy = false;
+	}
+
+	return 0;
+}
+
+static int mos7840_resume(struct usb_serial *serial)
+{
+	struct moschip_port *mos7840_port;
+	struct usb_serial_port *port;
+	int res;
+	int i;
+
+	for (i = 0; i < serial->num_ports; ++i) {
+		port = serial->port[i];
+		if (!tty_port_initialized(&port->port))
+			continue;
+
+		mos7840_port = usb_get_serial_port_data(port);
+
+		mos7840_port->read_urb_busy = true;
+		res = usb_submit_urb(mos7840_port->read_urb, GFP_NOIO);
+		if (res)
+			mos7840_port->read_urb_busy = false;
+	}
+
+	return 0;
+}
+
 static struct usb_serial_driver moschip7840_4port_device = {
 	.driver = {
 		   .owner = THIS_MODULE,
@@ -1762,6 +1805,8 @@
 	.port_probe = mos7840_port_probe,
 	.port_remove = mos7840_port_remove,
 	.read_bulk_callback = mos7840_bulk_in_callback,
+	.suspend = mos7840_suspend,
+	.resume = mos7840_resume,
 };
 
 static struct usb_serial_driver * const serial_drivers[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/option.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/option.c
@@ -162,6 +162,8 @@
 #define NOVATELWIRELESS_PRODUCT_G2		0xA010
 #define NOVATELWIRELESS_PRODUCT_MC551		0xB001
 
+#define UBLOX_VENDOR_ID				0x1546
+
 /* AMOI PRODUCTS */
 #define AMOI_VENDOR_ID				0x1614
 #define AMOI_PRODUCT_H01			0x0800
@@ -198,6 +200,11 @@
 
 #define DELL_PRODUCT_5821E			0x81d7
 #define DELL_PRODUCT_5821E_ESIM			0x81e0
+#define DELL_PRODUCT_5829E_ESIM			0x81e4
+#define DELL_PRODUCT_5829E			0x81e6
+
+#define DELL_PRODUCT_FM101R_ESIM		0x8213
+#define DELL_PRODUCT_FM101R			0x8215
 
 #define KYOCERA_VENDOR_ID			0x0c88
 #define KYOCERA_PRODUCT_KPC650			0x17da
@@ -238,22 +245,46 @@
 #define QUECTEL_PRODUCT_UC15			0x9090
 /* These u-blox products use Qualcomm's vendor ID */
 #define UBLOX_PRODUCT_R410M			0x90b2
-#define UBLOX_PRODUCT_R6XX			0x90fa
 /* These Yuga products use Qualcomm's vendor ID */
 #define YUGA_PRODUCT_CLM920_NC5			0x9625
 
 #define QUECTEL_VENDOR_ID			0x2c7c
 /* These Quectel products use Quectel's vendor ID */
 #define QUECTEL_PRODUCT_EC21			0x0121
+#define QUECTEL_PRODUCT_RG650V			0x0122
+#define QUECTEL_PRODUCT_EM061K_LTA		0x0123
+#define QUECTEL_PRODUCT_EM061K_LMS		0x0124
 #define QUECTEL_PRODUCT_EC25			0x0125
+#define QUECTEL_PRODUCT_EM060K_128		0x0128
+#define QUECTEL_PRODUCT_EM060K_129		0x0129
+#define QUECTEL_PRODUCT_EM060K_12a		0x012a
+#define QUECTEL_PRODUCT_EM060K_12b		0x012b
+#define QUECTEL_PRODUCT_EM060K_12c		0x012c
 #define QUECTEL_PRODUCT_EG91			0x0191
 #define QUECTEL_PRODUCT_EG95			0x0195
 #define QUECTEL_PRODUCT_BG96			0x0296
 #define QUECTEL_PRODUCT_EP06			0x0306
+#define QUECTEL_PRODUCT_EM05G			0x030a
+#define QUECTEL_PRODUCT_EM060K			0x030b
+#define QUECTEL_PRODUCT_EM05G_CS		0x030c
+#define QUECTEL_PRODUCT_EM05GV2			0x030e
+#define QUECTEL_PRODUCT_EM05CN_SG		0x0310
+#define QUECTEL_PRODUCT_EM05G_SG		0x0311
+#define QUECTEL_PRODUCT_EM05CN			0x0312
+#define QUECTEL_PRODUCT_EM05G_GR		0x0313
+#define QUECTEL_PRODUCT_EM05G_RS		0x0314
 #define QUECTEL_PRODUCT_EM12			0x0512
 #define QUECTEL_PRODUCT_RM500Q			0x0800
+#define QUECTEL_PRODUCT_RM520N			0x0801
+#define QUECTEL_PRODUCT_EC200U			0x0901
+#define QUECTEL_PRODUCT_EG912Y			0x6001
 #define QUECTEL_PRODUCT_EC200S_CN		0x6002
+#define QUECTEL_PRODUCT_EC200A			0x6005
+#define QUECTEL_PRODUCT_EG916Q			0x6007
+#define QUECTEL_PRODUCT_EM061K_LWW		0x6008
+#define QUECTEL_PRODUCT_EM061K_LCN		0x6009
 #define QUECTEL_PRODUCT_EC200T			0x6026
+#define QUECTEL_PRODUCT_RM500K			0x7001
 
 #define CMOTECH_VENDOR_ID			0x16d8
 #define CMOTECH_PRODUCT_6001			0x6001
@@ -388,6 +419,8 @@
 #define LONGCHEER_VENDOR_ID			0x1c9e
 
 /* 4G Systems products */
+/* This one was sold as the VW and Skoda "Carstick LTE" */
+#define FOUR_G_SYSTEMS_PRODUCT_CARSTICK_LTE	0x7605
 /* This is the 4G XS Stick W14 a.k.a. Mobilcom Debitel Surf-Stick *
  * It seems to contain a Qualcomm QSC6240/6290 chipset            */
 #define FOUR_G_SYSTEMS_PRODUCT_W14		0x9603
@@ -430,6 +463,12 @@
 #define CINTERION_PRODUCT_CLS8			0x00b0
 #define CINTERION_PRODUCT_MV31_MBIM		0x00b3
 #define CINTERION_PRODUCT_MV31_RMNET		0x00b7
+#define CINTERION_PRODUCT_MV31_2_MBIM		0x00b8
+#define CINTERION_PRODUCT_MV31_2_RMNET		0x00b9
+#define CINTERION_PRODUCT_MV32_WA		0x00f1
+#define CINTERION_PRODUCT_MV32_WB		0x00f2
+#define CINTERION_PRODUCT_MV32_WA_RMNET		0x00f3
+#define CINTERION_PRODUCT_MV32_WB_RMNET		0x00f4
 
 /* Olivetti products */
 #define OLIVETTI_VENDOR_ID			0x0b3c
@@ -565,6 +604,20 @@
 #define WETELECOM_PRODUCT_6802			0x6802
 #define WETELECOM_PRODUCT_WMD300		0x6803
 
+/* OPPO products */
+#define OPPO_VENDOR_ID				0x22d9
+#define OPPO_PRODUCT_R11			0x276c
+
+/* Sierra Wireless products */
+#define SIERRA_VENDOR_ID			0x1199
+#define SIERRA_PRODUCT_EM9191			0x90d3
+
+/* UNISOC (Spreadtrum) products */
+#define UNISOC_VENDOR_ID			0x1782
+/* TOZED LT70-C based on UNISOC SL8563 uses UNISOC's vendor ID */
+#define TOZED_PRODUCT_LT70C			0x4055
+/* Luat Air72*U series based on UNISOC UIS8910 uses UNISOC's vendor ID */
+#define LUAT_PRODUCT_AIR720U			0x4e00
 
 /* Device flags */
 
@@ -1063,6 +1116,12 @@
 	  .driver_info = RSVD(0) | RSVD(1) | RSVD(6) },
 	{ USB_DEVICE(DELL_VENDOR_ID, DELL_PRODUCT_5821E_ESIM),
 	  .driver_info = RSVD(0) | RSVD(1) | RSVD(6) },
+	{ USB_DEVICE(DELL_VENDOR_ID, DELL_PRODUCT_5829E),
+	  .driver_info = RSVD(0) | RSVD(6) },
+	{ USB_DEVICE(DELL_VENDOR_ID, DELL_PRODUCT_5829E_ESIM),
+	  .driver_info = RSVD(0) | RSVD(6) },
+	{ USB_DEVICE_INTERFACE_CLASS(DELL_VENDOR_ID, DELL_PRODUCT_FM101R, 0xff) },
+	{ USB_DEVICE_INTERFACE_CLASS(DELL_VENDOR_ID, DELL_PRODUCT_FM101R_ESIM, 0xff) },
 	{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_E100A) },	/* ADU-E100, ADU-310 */
 	{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) },
 	{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) },
@@ -1104,8 +1163,20 @@
 	/* u-blox products using Qualcomm vendor ID */
 	{ USB_DEVICE(QUALCOMM_VENDOR_ID, UBLOX_PRODUCT_R410M),
 	  .driver_info = RSVD(1) | RSVD(3) },
-	{ USB_DEVICE(QUALCOMM_VENDOR_ID, UBLOX_PRODUCT_R6XX),
+	{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x908b),	/* u-blox LARA-R6 00B */
+	  .driver_info = RSVD(4) },
+	{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x90fa),
 	  .driver_info = RSVD(3) },
+	/* u-blox products */
+	{ USB_DEVICE(UBLOX_VENDOR_ID, 0x1311) },	/* u-blox LARA-R6 01B */
+	{ USB_DEVICE(UBLOX_VENDOR_ID, 0x1312),		/* u-blox LARA-R6 01B (RMNET) */
+	  .driver_info = RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(UBLOX_VENDOR_ID, 0x1313, 0xff) },	/* u-blox LARA-R6 01B (ECM) */
+	{ USB_DEVICE(UBLOX_VENDOR_ID, 0x1341) },	/* u-blox LARA-L6 */
+	{ USB_DEVICE(UBLOX_VENDOR_ID, 0x1342),		/* u-blox LARA-L6 (RMNET) */
+	  .driver_info = RSVD(4) },
+	{ USB_DEVICE(UBLOX_VENDOR_ID, 0x1343),		/* u-blox LARA-L6 (ECM) */
+	  .driver_info = RSVD(4) },
 	/* Quectel products using Quectel vendor ID */
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC21, 0xff, 0xff, 0xff),
 	  .driver_info = NUMEP2 },
@@ -1119,22 +1190,85 @@
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EG95, 0xff, 0xff, 0xff),
 	  .driver_info = NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EG95, 0xff, 0, 0) },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0203, 0xff), /* BG95-M3 */
+	  .driver_info = ZLP },
 	{ USB_DEVICE(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG96),
 	  .driver_info = RSVD(4) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05CN, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05CN_SG, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_GR, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05GV2, 0xff),
+	  .driver_info = RSVD(4) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_CS, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_RS, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LMS, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LMS, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LMS, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LTA, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LTA, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LTA, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LWW, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LWW, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LWW, 0xff, 0xff, 0x40) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0xff, 0x30) },	/* EM160R-GL */
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */
+	  .driver_info = RSVD(3) | ZLP },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0x40) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),
 	  .driver_info = ZLP },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM520N, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM520N, 0xff, 0, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM520N, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0900, 0xff, 0, 0), /* RM500U-CN */
+	  .driver_info = ZLP },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200A, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200U, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EG912Y, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EG916Q, 0xff, 0x00, 0x00) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RG650V, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RG650V, 0xff, 0, 0) },
 
 	{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
 	{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
@@ -1187,6 +1321,7 @@
 	 .driver_info = NCTRL(0) | RSVD(3) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1033, 0xff),	/* Telit LE910C1-EUX (ECM) */
 	 .driver_info = NCTRL(0) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1035, 0xff) }, /* Telit LE910C4-WWX (ECM) */
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_LE922_USBCFG0),
 	  .driver_info = RSVD(0) | RSVD(1) | NCTRL(2) | RSVD(3) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_LE922_USBCFG1),
@@ -1211,6 +1346,10 @@
 	  .driver_info = NCTRL(0) | RSVD(1) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1056, 0xff),	/* Telit FD980 */
 	  .driver_info = NCTRL(2) | RSVD(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1057, 0xff),	/* Telit FN980 */
+	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1058, 0xff),	/* Telit FN980 (PCIe) */
+	  .driver_info = NCTRL(0) | RSVD(1) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1060, 0xff),	/* Telit LN920 (rmnet) */
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1061, 0xff),	/* Telit LN920 (MBIM) */
@@ -1219,6 +1358,74 @@
 	  .driver_info = NCTRL(2) | RSVD(3) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1063, 0xff),	/* Telit LN920 (ECM) */
 	  .driver_info = NCTRL(0) | RSVD(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1070, 0xff),	/* Telit FN990A (rmnet) */
+	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1071, 0xff),	/* Telit FN990A (MBIM) */
+	  .driver_info = NCTRL(0) | RSVD(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1072, 0xff),	/* Telit FN990A (RNDIS) */
+	  .driver_info = NCTRL(2) | RSVD(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1073, 0xff),	/* Telit FN990A (ECM) */
+	  .driver_info = NCTRL(0) | RSVD(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1075, 0xff),	/* Telit FN990A (PCIe) */
+	  .driver_info = RSVD(0) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1080, 0xff),	/* Telit FE990A (rmnet) */
+	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1081, 0xff),	/* Telit FE990A (MBIM) */
+	  .driver_info = NCTRL(0) | RSVD(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1082, 0xff),	/* Telit FE990A (RNDIS) */
+	  .driver_info = NCTRL(2) | RSVD(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff),	/* Telit FE990A (ECM) */
+	  .driver_info = NCTRL(0) | RSVD(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a0, 0xff),	/* Telit FN20C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a2, 0xff),	/* Telit FN920C04 (MBIM) */
+	  .driver_info = NCTRL(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a4, 0xff),	/* Telit FN20C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a7, 0xff),	/* Telit FN920C04 (MBIM) */
+	  .driver_info = NCTRL(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a9, 0xff),	/* Telit FN20C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10aa, 0xff),	/* Telit FN920C04 (MBIM) */
+	  .driver_info = NCTRL(3) | RSVD(4) | RSVD(5) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b0, 0xff, 0xff, 0x30),	/* Telit FE990B (rmnet) */
+	  .driver_info = NCTRL(5) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b0, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b0, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b1, 0xff, 0xff, 0x30),	/* Telit FE990B (MBIM) */
+	  .driver_info = NCTRL(6) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b1, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b1, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b2, 0xff, 0xff, 0x30),	/* Telit FE990B (RNDIS) */
+	  .driver_info = NCTRL(6) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b2, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b2, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b3, 0xff, 0xff, 0x30),	/* Telit FE990B (ECM) */
+	  .driver_info = NCTRL(6) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b3, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b3, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c0, 0xff),	/* Telit FE910C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c4, 0xff),	/* Telit FE910C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c8, 0xff),	/* Telit FE910C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d0, 0xff, 0xff, 0x30),	/* Telit FN990B (rmnet) */
+	  .driver_info = NCTRL(5) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d0, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d0, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d1, 0xff, 0xff, 0x30),	/* Telit FN990B (MBIM) */
+	  .driver_info = NCTRL(6) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d1, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d1, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d2, 0xff, 0xff, 0x30),	/* Telit FN990B (RNDIS) */
+	  .driver_info = NCTRL(6) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d2, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d2, 0xff, 0xff, 0x60) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d3, 0xff, 0xff, 0x30),	/* Telit FN990B (ECM) */
+	  .driver_info = NCTRL(6) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d3, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d3, 0xff, 0xff, 0x60) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910),
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(3) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),
@@ -1253,6 +1460,7 @@
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1231, 0xff),	/* Telit LE910Cx (RNDIS) */
 	  .driver_info = NCTRL(2) | RSVD(3) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x1250, 0xff, 0x00, 0x00) },	/* Telit LE910Cx (rmnet) */
 	{ USB_DEVICE(TELIT_VENDOR_ID, 0x1260),
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, 0x1261),
@@ -1261,12 +1469,26 @@
 	  .driver_info = NCTRL(0) | RSVD(1) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1901, 0xff),	/* Telit LN940 (MBIM) */
 	  .driver_info = NCTRL(0) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x3000, 0xff),	/* Telit FN912 */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x3001, 0xff),	/* Telit FN912 */
+	  .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x7010, 0xff),	/* Telit LE910-S1 (RNDIS) */
 	  .driver_info = NCTRL(2) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x7011, 0xff),	/* Telit LE910-S1 (ECM) */
 	  .driver_info = NCTRL(2) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x701a, 0xff),	/* Telit LE910R1 (RNDIS) */
+	  .driver_info = NCTRL(2) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x701b, 0xff),	/* Telit LE910R1 (ECM) */
+	  .driver_info = NCTRL(2) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x9000, 0xff),	/* Telit generic core-dump device */
+	  .driver_info = NCTRL(0) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, 0x9010),				/* Telit SBL FN980 flashing device */
 	  .driver_info = NCTRL(0) | ZLP },
+	{ USB_DEVICE(TELIT_VENDOR_ID, 0x9200),				/* Telit LE910S1 flashing device */
+	  .driver_info = NCTRL(0) | ZLP },
+	{ USB_DEVICE(TELIT_VENDOR_ID, 0x9201),				/* Telit LE910R1 flashing device */
+	  .driver_info = NCTRL(0) | ZLP },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622, 0xff, 0xff, 0xff) }, /* ZTE WCDMA products */
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0002, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) },
@@ -1406,7 +1628,8 @@
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0165, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0167, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(4) },
-	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0189, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0189, 0xff, 0xff, 0xff),
+	  .driver_info = RSVD(4) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0191, 0xff, 0xff, 0xff), /* ZTE EuFi890 */
 	  .driver_info = RSVD(4) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0196, 0xff, 0xff, 0xff) },
@@ -1639,6 +1862,8 @@
 	  .driver_info = RSVD(2) },
 	{ USB_DEVICE_INTERFACE_CLASS(ZTE_VENDOR_ID, 0x1476, 0xff) },	/* GosunCn ZTE WeLink ME3630 (ECM/NCM mode) */
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1481, 0xff, 0x00, 0x00) }, /* ZTE MF871A */
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1485, 0xff, 0xff, 0xff),  /* ZTE MF286D */
+	  .driver_info = RSVD(5) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1533, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1534, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1535, 0xff, 0xff, 0xff) },
@@ -1886,6 +2111,8 @@
 	  .driver_info = RSVD(2) },
 	{ USB_DEVICE(AIRPLUS_VENDOR_ID, AIRPLUS_PRODUCT_MCD650) },
 	{ USB_DEVICE(TLAYTECH_VENDOR_ID, TLAYTECH_PRODUCT_TEU800) },
+	{ USB_DEVICE(LONGCHEER_VENDOR_ID, FOUR_G_SYSTEMS_PRODUCT_CARSTICK_LTE),
+	  .driver_info = RSVD(0) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, FOUR_G_SYSTEMS_PRODUCT_W14),
 	  .driver_info = NCTRL(0) | NCTRL(1) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, FOUR_G_SYSTEMS_PRODUCT_W100),
@@ -1897,6 +2124,10 @@
 	  .driver_info = RSVD(3) },
 	{ USB_DEVICE_INTERFACE_CLASS(LONGCHEER_VENDOR_ID, 0x9803, 0xff),
 	  .driver_info = RSVD(4) },
+	{ USB_DEVICE(LONGCHEER_VENDOR_ID, 0x9b05),	/* Longsung U8300 */
+	  .driver_info = RSVD(4) | RSVD(5) },
+	{ USB_DEVICE(LONGCHEER_VENDOR_ID, 0x9b3c),	/* Longsung U9300 */
+	  .driver_info = RSVD(0) | RSVD(4) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, ZOOM_PRODUCT_4597) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, IBALL_3_5G_CONNECT) },
 	{ USB_DEVICE(HAIER_VENDOR_ID, HAIER_PRODUCT_CE100) },
@@ -1945,6 +2176,18 @@
 	  .driver_info = RSVD(3)},
 	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV31_RMNET, 0xff),
 	  .driver_info = RSVD(0)},
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV31_2_MBIM, 0xff),
+	  .driver_info = RSVD(3)},
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV31_2_RMNET, 0xff),
+	  .driver_info = RSVD(0)},
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV32_WA, 0xff),
+	  .driver_info = RSVD(3)},
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV32_WA_RMNET, 0xff),
+	  .driver_info = RSVD(0) },
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV32_WB, 0xff),
+	  .driver_info = RSVD(3)},
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_MV32_WB_RMNET, 0xff),
+	  .driver_info = RSVD(0) },
 	{ USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD100),
 	  .driver_info = RSVD(4) },
 	{ USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD120),
@@ -2031,6 +2274,12 @@
 	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_7106_2COM, 0x02, 0x02, 0x01) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM2, 0xff, 0x02, 0x01) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM2, 0xff, 0x00, 0x00) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, 0x7126, 0xff, 0x00, 0x00),
+	  .driver_info = NCTRL(2) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, 0x7127, 0xff, 0x00, 0x00),
+	  .driver_info = NCTRL(2) | NCTRL(3) | NCTRL(4) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, 0x7129, 0xff, 0x00, 0x00),        /* MediaTek T7XX  */
+	  .driver_info = NCTRL(2) | NCTRL(3) | NCTRL(4) },
 	{ USB_DEVICE(CELLIENT_VENDOR_ID, CELLIENT_PRODUCT_MEN200) },
 	{ USB_DEVICE(CELLIENT_VENDOR_ID, CELLIENT_PRODUCT_MPL200),
 	  .driver_info = RSVD(1) | RSVD(4) },
@@ -2083,21 +2332,113 @@
 	  .driver_info = RSVD(0) | RSVD(1) | RSVD(6) },
 	{ USB_DEVICE(0x0489, 0xe0b5),						/* Foxconn T77W968 ESIM */
 	  .driver_info = RSVD(0) | RSVD(1) | RSVD(6) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x0489, 0xe0da, 0xff),                     /* Foxconn T99W265 MBIM variant */
+	  .driver_info = RSVD(3) | RSVD(5) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x0489, 0xe0db, 0xff),			/* Foxconn T99W265 MBIM */
 	  .driver_info = RSVD(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x0489, 0xe0ee, 0xff),			/* Foxconn T99W368 MBIM */
+	  .driver_info = RSVD(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x0489, 0xe0f0, 0xff),			/* Foxconn T99W373 MBIM */
+	  .driver_info = RSVD(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x0489, 0xe145, 0xff),			/* Foxconn T99W651 RNDIS */
+	  .driver_info = RSVD(5) | RSVD(6) },
 	{ USB_DEVICE(0x1508, 0x1001),						/* Fibocom NL668 (IOT version) */
 	  .driver_info = RSVD(4) | RSVD(5) | RSVD(6) },
+	{ USB_DEVICE(0x1782, 0x4d10) },						/* Fibocom L610 (AT mode) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x1782, 0x4d11, 0xff) },			/* Fibocom L610 (ECM/RNDIS mode) */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0001, 0xff, 0xff, 0xff) },	/* Fibocom L716-EU (ECM/RNDIS mode) */
 	{ USB_DEVICE(0x2cb7, 0x0104),						/* Fibocom NL678 series */
 	  .driver_info = RSVD(4) | RSVD(5) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff),			/* Fibocom NL678 series */
 	  .driver_info = RSVD(6) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0106, 0xff) },			/* Fibocom MA510 (ECM mode w/ diag intf.) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x010a, 0xff) },			/* Fibocom MA510 (ECM mode) */
 	{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0xff, 0x30) },	/* Fibocom FG150 Diag */
 	{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0, 0) },		/* Fibocom FG150 AT */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0111, 0xff) },			/* Fibocom FM160 (MBIM mode) */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0112, 0xff, 0xff, 0x30) },	/* Fibocom FG132 Diag */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0112, 0xff, 0xff, 0x40) },	/* Fibocom FG132 AT */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x0112, 0xff, 0, 0) },		/* Fibocom FG132 NMEA */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0115, 0xff),			/* Fibocom FM135 (laptop MBIM) */
+	  .driver_info = RSVD(5) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) },			/* Fibocom NL668-AM/NL652-EU (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff) },			/* Fibocom FM101-GL (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a3, 0xff) },			/* Fibocom FM101-GL (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4, 0xff),			/* Fibocom FM101-GL (laptop MBIM) */
+	  .driver_info = RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a04, 0xff) },			/* Fibocom FM650-CN (ECM mode) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a05, 0xff) },			/* Fibocom FM650-CN (NCM mode) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a06, 0xff) },			/* Fibocom FM650-CN (RNDIS mode) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a07, 0xff) },			/* Fibocom FM650-CN (MBIM mode) */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d41, 0xff, 0, 0) },		/* MeiG Smart SLM320 */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d57, 0xff, 0, 0) },		/* MeiG Smart SLM770A */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0, 0) },		/* MeiG Smart SRM815 */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0x10, 0x02) },	/* MeiG Smart SLM828 */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0x10, 0x03) },	/* MeiG Smart SLM828 */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0xff, 0x30) },	/* MeiG Smart SRM815 and SRM825L */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0xff, 0x40) },	/* MeiG Smart SRM825L */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0xff, 0x60) },	/* MeiG Smart SRM825L */
 	{ USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff) },			/* LongSung M5710 */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff) },			/* GosunCn GM500 RNDIS */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff) },			/* GosunCn GM500 MBIM */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1406, 0xff) },			/* GosunCn GM500 ECM/NCM */
+	{ USB_DEVICE(0x33f8, 0x0104),						/* Rolling RW101-GL (laptop RMNET) */
+	  .driver_info = RSVD(4) | RSVD(5) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a2, 0xff) },			/* Rolling RW101-GL (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a3, 0xff) },			/* Rolling RW101-GL (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a4, 0xff),			/* Rolling RW101-GL (laptop MBIM) */
+	  .driver_info = RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x0115, 0xff),			/* Rolling RW135-GL (laptop MBIM) */
+	  .driver_info = RSVD(5) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x0802, 0xff),			/* Rolling RW350-GL (laptop MBIM) */
+	  .driver_info = RSVD(5) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0100, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for Global */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0100, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0100, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0101, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WRD for Global SKU */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0101, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0101, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0106, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WRD for China SKU */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0106, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0106, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0111, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for SA */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0111, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0111, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0112, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for EU */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0112, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0112, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0113, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for NA */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0113, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0113, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0115, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for China EDU */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0115, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0115, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0116, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for Golbal EDU */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0116, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x0116, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010a, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WRD for WWAN Ready */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010a, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010a, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010b, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for WWAN Ready */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010b, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010b, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010c, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WRD for WWAN Ready */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010c, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010c, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010d, 0xff, 0xff, 0x30) },	/* NetPrisma LCUK54-WWD for WWAN Ready */
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010d, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(0x3731, 0x010d, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(OPPO_VENDOR_ID, OPPO_PRODUCT_R11, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(UNISOC_VENDOR_ID, TOZED_PRODUCT_LT70C, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(UNISOC_VENDOR_ID, LUAT_PRODUCT_AIR720U, 0xff, 0, 0) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x1bbb, 0x0530, 0xff),			/* TCL IK512 MBIM */
+	  .driver_info = NCTRL(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x1bbb, 0x0640, 0xff),			/* TCL IK512 ECM */
+	  .driver_info = NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x2949, 0x8700, 0xff) },			/* Neoway N723-EA */
 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/pl2303.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/pl2303.c
@@ -106,6 +106,7 @@
 	{ USB_DEVICE(HP_VENDOR_ID, HP_LCM220_PRODUCT_ID) },
 	{ USB_DEVICE(HP_VENDOR_ID, HP_LCM960_PRODUCT_ID) },
 	{ USB_DEVICE(HP_VENDOR_ID, HP_LM920_PRODUCT_ID) },
+	{ USB_DEVICE(HP_VENDOR_ID, HP_LM930_PRODUCT_ID) },
 	{ USB_DEVICE(HP_VENDOR_ID, HP_LM940_PRODUCT_ID) },
 	{ USB_DEVICE(HP_VENDOR_ID, HP_TD620_PRODUCT_ID) },
 	{ USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) },
@@ -116,6 +117,8 @@
 	{ USB_DEVICE(ADLINK_VENDOR_ID, ADLINK_ND6530GC_PRODUCT_ID) },
 	{ USB_DEVICE(SMART_VENDOR_ID, SMART_PRODUCT_ID) },
 	{ USB_DEVICE(AT_VENDOR_ID, AT_VTKIT3_PRODUCT_ID) },
+	{ USB_DEVICE(IBM_VENDOR_ID, IBM_PRODUCT_ID) },
+	{ USB_DEVICE(MACROSILICON_VENDOR_ID, MACROSILICON_MS3020_PRODUCT_ID) },
 	{ }					/* Terminating entry */
 };
 
@@ -419,6 +422,9 @@
 	bcdUSB = le16_to_cpu(desc->bcdUSB);
 
 	switch (bcdUSB) {
+	case 0x101:
+		/* USB 1.0.1? Let's assume they meant 1.1... */
+		fallthrough;
 	case 0x110:
 		switch (bcdDevice) {
 		case 0x300:
@@ -431,20 +437,27 @@
 		break;
 	case 0x200:
 		switch (bcdDevice) {
-		case 0x100:
+		case 0x100:	/* GC */
+		case 0x105:
+			return TYPE_HXN;
+		case 0x300:	/* GT / TA */
+			if (pl2303_supports_hx_status(serial))
+				return TYPE_TA;
+			fallthrough;
 		case 0x305:
+		case 0x400:	/* GL */
 		case 0x405:
-			/*
-			 * Assume it's an HXN-type if the device doesn't
-			 * support the old read request value.
-			 */
-			if (!pl2303_supports_hx_status(serial))
-				return TYPE_HXN;
-			break;
-		case 0x300:
-			return TYPE_TA;
-		case 0x500:
-			return TYPE_TB;
+			return TYPE_HXN;
+		case 0x500:	/* GE / TB */
+			if (pl2303_supports_hx_status(serial))
+				return TYPE_TB;
+			fallthrough;
+		case 0x505:
+		case 0x600:	/* GS */
+		case 0x605:
+		case 0x700:	/* GR */
+		case 0x705:
+			return TYPE_HXN;
 		}
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/pl2303.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/pl2303.h
@@ -35,6 +35,9 @@
 #define ATEN_PRODUCT_UC232B	0x2022
 #define ATEN_PRODUCT_ID2	0x2118
 
+#define IBM_VENDOR_ID		0x04b3
+#define IBM_PRODUCT_ID		0x4016
+
 #define IODATA_VENDOR_ID	0x04bb
 #define IODATA_PRODUCT_ID	0x0a03
 #define IODATA_PRODUCT_ID_RSAQ5	0x0a0e
@@ -132,6 +135,7 @@
 #define HP_TD620_PRODUCT_ID	0x0956
 #define HP_LD960_PRODUCT_ID	0x0b39
 #define HP_LD381_PRODUCT_ID	0x0f7f
+#define HP_LM930_PRODUCT_ID	0x0f9b
 #define HP_LCM220_PRODUCT_ID	0x3139
 #define HP_LCM960_PRODUCT_ID	0x3239
 #define HP_LD220_PRODUCT_ID	0x3524
@@ -167,3 +171,7 @@
 /* Allied Telesis VT-Kit3 */
 #define AT_VENDOR_ID		0x0caa
 #define AT_VTKIT3_PRODUCT_ID	0x3001
+
+/* Macrosilicon MS3020 */
+#define MACROSILICON_VENDOR_ID		0x345f
+#define MACROSILICON_MS3020_PRODUCT_ID	0x3020
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/qcserial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/qcserial.c
@@ -166,6 +166,10 @@
 	{DEVICE_SWI(0x1199, 0x9090)},	/* Sierra Wireless EM7565 QDL */
 	{DEVICE_SWI(0x1199, 0x9091)},	/* Sierra Wireless EM7565 */
 	{DEVICE_SWI(0x1199, 0x90d2)},	/* Sierra Wireless EM9191 QDL */
+	{DEVICE_SWI(0x1199, 0x90e4)},	/* Sierra Wireless EM86xx QDL*/
+	{DEVICE_SWI(0x1199, 0x90e5)},	/* Sierra Wireless EM86xx */
+	{DEVICE_SWI(0x1199, 0xc080)},	/* Sierra Wireless EM7590 QDL */
+	{DEVICE_SWI(0x1199, 0xc081)},	/* Sierra Wireless EM7590 */
 	{DEVICE_SWI(0x413c, 0x81a2)},	/* Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card */
 	{DEVICE_SWI(0x413c, 0x81a3)},	/* Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card */
 	{DEVICE_SWI(0x413c, 0x81a4)},	/* Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card */
@@ -175,12 +179,15 @@
 	{DEVICE_SWI(0x413c, 0x81b3)},	/* Dell Wireless 5809e Gobi(TM) 4G LTE Mobile Broadband Card (rev3) */
 	{DEVICE_SWI(0x413c, 0x81b5)},	/* Dell Wireless 5811e QDL */
 	{DEVICE_SWI(0x413c, 0x81b6)},	/* Dell Wireless 5811e QDL */
+	{DEVICE_SWI(0x413c, 0x81c2)},	/* Dell Wireless 5811e */
 	{DEVICE_SWI(0x413c, 0x81cb)},	/* Dell Wireless 5816e QDL */
 	{DEVICE_SWI(0x413c, 0x81cc)},	/* Dell Wireless 5816e */
 	{DEVICE_SWI(0x413c, 0x81cf)},   /* Dell Wireless 5819 */
 	{DEVICE_SWI(0x413c, 0x81d0)},   /* Dell Wireless 5819 */
 	{DEVICE_SWI(0x413c, 0x81d1)},   /* Dell Wireless 5818 */
 	{DEVICE_SWI(0x413c, 0x81d2)},   /* Dell Wireless 5818 */
+	{DEVICE_SWI(0x413c, 0x8217)},	/* Dell Wireless DW5826e */
+	{DEVICE_SWI(0x413c, 0x8218)},	/* Dell Wireless DW5826e QDL */
 
 	/* Huawei devices */
 	{DEVICE_HWI(0x03f0, 0x581d)},	/* HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e) */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/quatech2.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/quatech2.c
@@ -525,7 +525,7 @@
 
 				newport = *(ch + 3);
 
-				if (newport > serial->num_ports) {
+				if (newport >= serial->num_ports) {
 					dev_err(&port->dev,
 						"%s - port change to invalid port: %i\n",
 						__func__, newport);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/sierra.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/sierra.c
@@ -737,7 +737,8 @@
 
 	/*
 	 * Need to take susp_lock to make sure port is not already being
-	 * resumed, but no need to hold it due to initialized
+	 * resumed, but no need to hold it due to the tty-port initialized
+	 * flag.
 	 */
 	spin_lock_irq(&intfdata->susp_lock);
 	if (--intfdata->open_ports == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/usb-serial-simple.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/usb-serial-simple.c
@@ -38,16 +38,6 @@
 	{ USB_DEVICE(0x0a21, 0x8001) }	/* MMT-7305WW */
 DEVICE(carelink, CARELINK_IDS);
 
-/* ZIO Motherboard USB driver */
-#define ZIO_IDS()			\
-	{ USB_DEVICE(0x1CBE, 0x0103) }
-DEVICE(zio, ZIO_IDS);
-
-/* Funsoft Serial USB driver */
-#define FUNSOFT_IDS()			\
-	{ USB_DEVICE(0x1404, 0xcddc) }
-DEVICE(funsoft, FUNSOFT_IDS);
-
 /* Infineon Flashloader driver */
 #define FLASHLOADER_IDS()		\
 	{ USB_DEVICE_INTERFACE_CLASS(0x058b, 0x0041, USB_CLASS_CDC_DATA) }, \
@@ -55,6 +45,11 @@
 	{ USB_DEVICE(0x8087, 0x0801) }
 DEVICE(flashloader, FLASHLOADER_IDS);
 
+/* Funsoft Serial USB driver */
+#define FUNSOFT_IDS()			\
+	{ USB_DEVICE(0x1404, 0xcddc) }
+DEVICE(funsoft, FUNSOFT_IDS);
+
 /* Google Serial USB SubClass */
 #define GOOGLE_IDS()						\
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x18d1,			\
@@ -63,16 +58,21 @@
 					0x01) }
 DEVICE(google, GOOGLE_IDS);
 
+/* HP4x (48/49) Generic Serial driver */
+#define HP4X_IDS()			\
+	{ USB_DEVICE(0x03f0, 0x0121) }
+DEVICE(hp4x, HP4X_IDS);
+
+/* KAUFMANN RKS+CAN VCP */
+#define KAUFMANN_IDS()			\
+	{ USB_DEVICE(0x16d0, 0x0870) }
+DEVICE(kaufmann, KAUFMANN_IDS);
+
 /* Libtransistor USB console */
 #define LIBTRANSISTOR_IDS()			\
 	{ USB_DEVICE(0x1209, 0x8b00) }
 DEVICE(libtransistor, LIBTRANSISTOR_IDS);
 
-/* ViVOpay USB Serial Driver */
-#define VIVOPAY_IDS()			\
-	{ USB_DEVICE(0x1d5f, 0x1004) }	/* ViVOpay 8800 */
-DEVICE(vivopay, VIVOPAY_IDS);
-
 /* Motorola USB Phone driver */
 #define MOTO_IDS()			\
 	{ USB_DEVICE(0x05c6, 0x3197) },	/* unknown Motorola phone */	\
@@ -91,15 +91,20 @@
 	{ USB_DEVICE(0x0cad, 0x9016) }	/* TPG2200 */
 DEVICE(motorola_tetra, MOTOROLA_TETRA_IDS);
 
+/* Nokia mobile phone driver */
+#define NOKIA_IDS()			\
+	{ USB_DEVICE(0x0421, 0x069a) }	/* Nokia 130 (RM-1035) */
+DEVICE(nokia, NOKIA_IDS);
+
 /* Novatel Wireless GPS driver */
 #define NOVATEL_IDS()			\
 	{ USB_DEVICE(0x09d7, 0x0100) }	/* NovAtel FlexPack GPS */
 DEVICE_N(novatel_gps, NOVATEL_IDS, 3);
 
-/* HP4x (48/49) Generic Serial driver */
-#define HP4X_IDS()			\
-	{ USB_DEVICE(0x03f0, 0x0121) }
-DEVICE(hp4x, HP4X_IDS);
+/* Siemens USB/MPI adapter */
+#define SIEMENS_IDS()			\
+	{ USB_DEVICE(0x908, 0x0004) }
+DEVICE(siemens_mpi, SIEMENS_IDS);
 
 /* Suunto ANT+ USB Driver */
 #define SUUNTO_IDS()			\
@@ -107,43 +112,52 @@
 	{ USB_DEVICE(0x0fcf, 0x1009) } /* Dynastream ANT USB-m Stick */
 DEVICE(suunto, SUUNTO_IDS);
 
-/* Siemens USB/MPI adapter */
-#define SIEMENS_IDS()			\
-	{ USB_DEVICE(0x908, 0x0004) }
-DEVICE(siemens_mpi, SIEMENS_IDS);
+/* ViVOpay USB Serial Driver */
+#define VIVOPAY_IDS()			\
+	{ USB_DEVICE(0x1d5f, 0x1004) }	/* ViVOpay 8800 */
+DEVICE(vivopay, VIVOPAY_IDS);
+
+/* ZIO Motherboard USB driver */
+#define ZIO_IDS()			\
+	{ USB_DEVICE(0x1CBE, 0x0103) }
+DEVICE(zio, ZIO_IDS);
 
 /* All of the above structures mushed into two lists */
 static struct usb_serial_driver * const serial_drivers[] = {
 	&carelink_device,
-	&zio_device,
-	&funsoft_device,
 	&flashloader_device,
+	&funsoft_device,
 	&google_device,
+	&hp4x_device,
+	&kaufmann_device,
 	&libtransistor_device,
-	&vivopay_device,
 	&moto_modem_device,
 	&motorola_tetra_device,
+	&nokia_device,
 	&novatel_gps_device,
-	&hp4x_device,
-	&suunto_device,
 	&siemens_mpi_device,
+	&suunto_device,
+	&vivopay_device,
+	&zio_device,
 	NULL
 };
 
 static const struct usb_device_id id_table[] = {
 	CARELINK_IDS(),
-	ZIO_IDS(),
-	FUNSOFT_IDS(),
 	FLASHLOADER_IDS(),
+	FUNSOFT_IDS(),
 	GOOGLE_IDS(),
+	HP4X_IDS(),
+	KAUFMANN_IDS(),
 	LIBTRANSISTOR_IDS(),
-	VIVOPAY_IDS(),
 	MOTO_IDS(),
 	MOTOROLA_TETRA_IDS(),
+	NOKIA_IDS(),
 	NOVATEL_IDS(),
-	HP4X_IDS(),
-	SUUNTO_IDS(),
 	SIEMENS_IDS(),
+	SUUNTO_IDS(),
+	VIVOPAY_IDS(),
+	ZIO_IDS(),
 	{ },
 };
 MODULE_DEVICE_TABLE(usb, id_table);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/usb-serial.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/usb-serial.c
@@ -292,7 +292,7 @@
  *
  * Shut down a USB serial port. Serialized against activate by the
  * tport mutex and kept to matching open/close pairs
- * of calls by the initialized flag.
+ * of calls by the tty-port initialized flag.
  *
  * Not called if tty is console.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/usb_debug.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/usb_debug.c
@@ -69,6 +69,11 @@
 	usb_serial_generic_process_read_urb(urb);
 }
 
+static void usb_debug_init_termios(struct tty_struct *tty)
+{
+	tty->termios.c_lflag &= ~(ECHO | ECHONL);
+}
+
 static struct usb_serial_driver debug_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
@@ -78,6 +83,7 @@
 	.num_ports =		1,
 	.bulk_out_size =	USB_DEBUG_MAX_PACKET_SIZE,
 	.break_ctl =		usb_debug_break_ctl,
+	.init_termios =		usb_debug_init_termios,
 	.process_read_urb =	usb_debug_process_read_urb,
 };
 
@@ -89,6 +95,7 @@
 	.id_table =		dbc_id_table,
 	.num_ports =		1,
 	.break_ctl =		usb_debug_break_ctl,
+	.init_termios =		usb_debug_init_termios,
 	.process_read_urb =	usb_debug_process_read_urb,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/usb_wwan.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/usb_wwan.c
@@ -389,7 +389,8 @@
 
 	/*
 	 * Need to take susp_lock to make sure port is not already being
-	 * resumed, but no need to hold it due to initialized
+	 * resumed, but no need to hold it due to the tty-port initialized
+	 * flag.
 	 */
 	spin_lock_irq(&intfdata->susp_lock);
 	if (--intfdata->open_ports == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/serial/whiteheat.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/serial/whiteheat.c
@@ -584,9 +584,8 @@
 		switch (command) {
 		case WHITEHEAT_GET_DTR_RTS:
 			info = usb_get_serial_port_data(port);
-			memcpy(&info->mcr, command_info->result_buffer,
-					sizeof(struct whiteheat_dr_info));
-				break;
+			info->mcr = command_info->result_buffer[0];
+			break;
 		}
 	}
 exit:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/alauda.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/alauda.c
@@ -105,6 +105,8 @@
 	unsigned char sense_key;
 	unsigned long sense_asc;	/* additional sense code */
 	unsigned long sense_ascq;	/* additional sense code qualifier */
+
+	bool media_initialized;
 };
 
 #define short_pack(lsb,msb) ( ((u16)(lsb)) | ( ((u16)(msb))<<8 ) )
@@ -318,7 +320,8 @@
 	rc = usb_stor_ctrl_transfer(us, us->recv_ctrl_pipe,
 		command, 0xc0, 0, 1, data, 2);
 
-	usb_stor_dbg(us, "Media status %02X %02X\n", data[0], data[1]);
+	if (rc == USB_STOR_XFER_GOOD)
+		usb_stor_dbg(us, "Media status %02X %02X\n", data[0], data[1]);
 
 	return rc;
 }
@@ -438,6 +441,8 @@
 		+ MEDIA_INFO(us).blockshift + MEDIA_INFO(us).pageshift);
 	MEDIA_INFO(us).pba_to_lba = kcalloc(num_zones, sizeof(u16*), GFP_NOIO);
 	MEDIA_INFO(us).lba_to_pba = kcalloc(num_zones, sizeof(u16*), GFP_NOIO);
+	if (MEDIA_INFO(us).pba_to_lba == NULL || MEDIA_INFO(us).lba_to_pba == NULL)
+		return USB_STOR_TRANSPORT_ERROR;
 
 	if (alauda_reset_media(us) != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
@@ -452,9 +457,14 @@
 static int alauda_check_media(struct us_data *us)
 {
 	struct alauda_info *info = (struct alauda_info *) us->extra;
-	unsigned char status[2];
+	unsigned char *status = us->iobuf;
+	int rc;
 
-	alauda_get_media_status(us, status);
+	rc = alauda_get_media_status(us, status);
+	if (rc != USB_STOR_XFER_GOOD) {
+		status[0] = 0xF0;	/* Pretend there's no media */
+		status[1] = 0;
+	}
 
 	/* Check for no media or door open */
 	if ((status[0] & 0x80) || ((status[0] & 0x1F) == 0x10)
@@ -468,11 +478,12 @@
 	}
 
 	/* Check for media change */
-	if (status[0] & 0x08) {
+	if (status[0] & 0x08 || !info->media_initialized) {
 		usb_stor_dbg(us, "Media change detected\n");
 		alauda_free_maps(&MEDIA_INFO(us));
-		alauda_init_media(us);
-
+		rc = alauda_init_media(us);
+		if (rc == USB_STOR_TRANSPORT_GOOD)
+			info->media_initialized = true;
 		info->sense_key = UNIT_ATTENTION;
 		info->sense_asc = 0x28;
 		info->sense_ascq = 0x00;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/ene_ub6250.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/ene_ub6250.c
@@ -237,36 +237,33 @@
 #define memstick_logaddr(logadr1, logadr0) ((((u16)(logadr1)) << 8) | (logadr0))
 
 
-struct SD_STATUS {
-	u8    Insert:1;
-	u8    Ready:1;
-	u8    MediaChange:1;
-	u8    IsMMC:1;
-	u8    HiCapacity:1;
-	u8    HiSpeed:1;
-	u8    WtP:1;
-	u8    Reserved:1;
-};
-
-struct MS_STATUS {
-	u8    Insert:1;
-	u8    Ready:1;
-	u8    MediaChange:1;
-	u8    IsMSPro:1;
-	u8    IsMSPHG:1;
-	u8    Reserved1:1;
-	u8    WtP:1;
-	u8    Reserved2:1;
-};
-
-struct SM_STATUS {
-	u8    Insert:1;
-	u8    Ready:1;
-	u8    MediaChange:1;
-	u8    Reserved:3;
-	u8    WtP:1;
-	u8    IsMS:1;
-};
+/* SD_STATUS bits */
+#define SD_Insert	BIT(0)
+#define SD_Ready	BIT(1)
+#define SD_MediaChange	BIT(2)
+#define SD_IsMMC	BIT(3)
+#define SD_HiCapacity	BIT(4)
+#define SD_HiSpeed	BIT(5)
+#define SD_WtP		BIT(6)
+			/* Bit 7 reserved */
+
+/* MS_STATUS bits */
+#define MS_Insert	BIT(0)
+#define MS_Ready	BIT(1)
+#define MS_MediaChange	BIT(2)
+#define MS_IsMSPro	BIT(3)
+#define MS_IsMSPHG	BIT(4)
+			/* Bit 5 reserved */
+#define MS_WtP		BIT(6)
+			/* Bit 7 reserved */
+
+/* SM_STATUS bits */
+#define SM_Insert	BIT(0)
+#define SM_Ready	BIT(1)
+#define SM_MediaChange	BIT(2)
+			/* Bits 3-5 reserved */
+#define SM_WtP		BIT(6)
+#define SM_IsMS		BIT(7)
 
 struct ms_bootblock_cis {
 	u8 bCistplDEVICE[6];    /* 0 */
@@ -437,9 +434,9 @@
 	u8		*bbuf;
 
 	/* for 6250 code */
-	struct SD_STATUS	SD_Status;
-	struct MS_STATUS	MS_Status;
-	struct SM_STATUS	SM_Status;
+	u8		SD_Status;
+	u8		MS_Status;
+	u8		SM_Status;
 
 	/* ----- SD Control Data ---------------- */
 	/*SD_REGISTER SD_Regs; */
@@ -602,7 +599,7 @@
 {
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *) us->extra;
 
-	if (info->SD_Status.Insert && info->SD_Status.Ready)
+	if ((info->SD_Status & SD_Insert) && (info->SD_Status & SD_Ready))
 		return USB_STOR_TRANSPORT_GOOD;
 	else {
 		ene_sd_init(us);
@@ -622,7 +619,7 @@
 		0x0b, 0x00, 0x80, 0x08, 0x00, 0x00,
 		0x71, 0xc0, 0x00, 0x00, 0x02, 0x00 };
 
-	if (info->SD_Status.WtP)
+	if (info->SD_Status & SD_WtP)
 		usb_stor_set_xfer_buf(mediaWP, 12, srb);
 	else
 		usb_stor_set_xfer_buf(mediaNoWP, 12, srb);
@@ -641,9 +638,9 @@
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *) us->extra;
 
 	usb_stor_dbg(us, "sd_scsi_read_capacity\n");
-	if (info->SD_Status.HiCapacity) {
+	if (info->SD_Status & SD_HiCapacity) {
 		bl_len = 0x200;
-		if (info->SD_Status.IsMMC)
+		if (info->SD_Status & SD_IsMMC)
 			bl_num = info->HC_C_SIZE-1;
 		else
 			bl_num = (info->HC_C_SIZE + 1) * 1024 - 1;
@@ -693,7 +690,7 @@
 		return USB_STOR_TRANSPORT_ERROR;
 	}
 
-	if (info->SD_Status.HiCapacity)
+	if (info->SD_Status & SD_HiCapacity)
 		bnByte = bn;
 
 	/* set up the command wrapper */
@@ -733,7 +730,7 @@
 		return USB_STOR_TRANSPORT_ERROR;
 	}
 
-	if (info->SD_Status.HiCapacity)
+	if (info->SD_Status & SD_HiCapacity)
 		bnByte = bn;
 
 	/* set up the command wrapper */
@@ -942,7 +939,7 @@
 	struct ms_lib_type_extdat ExtraData;
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *) us->extra;
 
-	PageBuffer = kmalloc(MS_BYTES_PER_PAGE, GFP_KERNEL);
+	PageBuffer = kzalloc(MS_BYTES_PER_PAGE * 2, GFP_KERNEL);
 	if (PageBuffer == NULL)
 		return (u32)-1;
 
@@ -1456,7 +1453,7 @@
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *)(us->extra);
 
 	/* pr_info("MS_SCSI_Test_Unit_Ready\n"); */
-	if (info->MS_Status.Insert && info->MS_Status.Ready) {
+	if ((info->MS_Status & MS_Insert) && (info->MS_Status & MS_Ready)) {
 		return USB_STOR_TRANSPORT_GOOD;
 	} else {
 		ene_ms_init(us);
@@ -1476,7 +1473,7 @@
 		0x0b, 0x00, 0x80, 0x08, 0x00, 0x00,
 		0x71, 0xc0, 0x00, 0x00, 0x02, 0x00 };
 
-	if (info->MS_Status.WtP)
+	if (info->MS_Status & MS_WtP)
 		usb_stor_set_xfer_buf(mediaWP, 12, srb);
 	else
 		usb_stor_set_xfer_buf(mediaNoWP, 12, srb);
@@ -1495,7 +1492,7 @@
 
 	usb_stor_dbg(us, "ms_scsi_read_capacity\n");
 	bl_len = 0x200;
-	if (info->MS_Status.IsMSPro)
+	if (info->MS_Status & MS_IsMSPro)
 		bl_num = info->MSP_TotalBlock - 1;
 	else
 		bl_num = info->MS_Lib.NumberOfLogBlock * info->MS_Lib.blockSize * 2 - 1;
@@ -1650,7 +1647,7 @@
 	if (bn > info->bl_num)
 		return USB_STOR_TRANSPORT_ERROR;
 
-	if (info->MS_Status.IsMSPro) {
+	if (info->MS_Status & MS_IsMSPro) {
 		result = ene_load_bincode(us, MSP_RW_PATTERN);
 		if (result != USB_STOR_XFER_GOOD) {
 			usb_stor_dbg(us, "Load MPS RW pattern Fail !!\n");
@@ -1751,7 +1748,7 @@
 	if (bn > info->bl_num)
 		return USB_STOR_TRANSPORT_ERROR;
 
-	if (info->MS_Status.IsMSPro) {
+	if (info->MS_Status & MS_IsMSPro) {
 		result = ene_load_bincode(us, MSP_RW_PATTERN);
 		if (result != USB_STOR_XFER_GOOD) {
 			pr_info("Load MSP RW pattern Fail !!\n");
@@ -1859,12 +1856,12 @@
 
 	tmpreg = (u16) reg4b;
 	reg4b = *(u32 *)(&buf[0x14]);
-	if (info->SD_Status.HiCapacity && !info->SD_Status.IsMMC)
+	if ((info->SD_Status & SD_HiCapacity) && !(info->SD_Status & SD_IsMMC))
 		info->HC_C_SIZE = (reg4b >> 8) & 0x3fffff;
 
 	info->SD_C_SIZE = ((tmpreg & 0x03) << 10) | (u16)(reg4b >> 22);
 	info->SD_C_SIZE_MULT = (u8)(reg4b >> 7)  & 0x07;
-	if (info->SD_Status.HiCapacity && info->SD_Status.IsMMC)
+	if ((info->SD_Status & SD_HiCapacity) && (info->SD_Status & SD_IsMMC))
 		info->HC_C_SIZE = *(u32 *)(&buf[0x100]);
 
 	if (info->SD_READ_BL_LEN > SD_BLOCK_LEN) {
@@ -2076,6 +2073,7 @@
 	u16 MSP_BlockSize, MSP_UserAreaBlocks;
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *) us->extra;
 	u8 *bbuf = info->bbuf;
+	unsigned int s;
 
 	printk(KERN_INFO "transport --- ENE_MSInit\n");
 
@@ -2100,15 +2098,16 @@
 		return USB_STOR_TRANSPORT_ERROR;
 	}
 	/* the same part to test ENE */
-	info->MS_Status = *(struct MS_STATUS *) bbuf;
+	info->MS_Status = bbuf[0];
 
-	if (info->MS_Status.Insert && info->MS_Status.Ready) {
-		printk(KERN_INFO "Insert     = %x\n", info->MS_Status.Insert);
-		printk(KERN_INFO "Ready      = %x\n", info->MS_Status.Ready);
-		printk(KERN_INFO "IsMSPro    = %x\n", info->MS_Status.IsMSPro);
-		printk(KERN_INFO "IsMSPHG    = %x\n", info->MS_Status.IsMSPHG);
-		printk(KERN_INFO "WtP= %x\n", info->MS_Status.WtP);
-		if (info->MS_Status.IsMSPro) {
+	s = info->MS_Status;
+	if ((s & MS_Insert) && (s & MS_Ready)) {
+		printk(KERN_INFO "Insert     = %x\n", !!(s & MS_Insert));
+		printk(KERN_INFO "Ready      = %x\n", !!(s & MS_Ready));
+		printk(KERN_INFO "IsMSPro    = %x\n", !!(s & MS_IsMSPro));
+		printk(KERN_INFO "IsMSPHG    = %x\n", !!(s & MS_IsMSPHG));
+		printk(KERN_INFO "WtP= %x\n", !!(s & MS_WtP));
+		if (s & MS_IsMSPro) {
 			MSP_BlockSize      = (bbuf[6] << 8) | bbuf[7];
 			MSP_UserAreaBlocks = (bbuf[10] << 8) | bbuf[11];
 			info->MSP_TotalBlock = MSP_BlockSize * MSP_UserAreaBlocks;
@@ -2169,17 +2168,17 @@
 		return USB_STOR_TRANSPORT_ERROR;
 	}
 
-	info->SD_Status =  *(struct SD_STATUS *) bbuf;
-	if (info->SD_Status.Insert && info->SD_Status.Ready) {
-		struct SD_STATUS *s = &info->SD_Status;
+	info->SD_Status = bbuf[0];
+	if ((info->SD_Status & SD_Insert) && (info->SD_Status & SD_Ready)) {
+		unsigned int s = info->SD_Status;
 
 		ene_get_card_status(us, bbuf);
-		usb_stor_dbg(us, "Insert     = %x\n", s->Insert);
-		usb_stor_dbg(us, "Ready      = %x\n", s->Ready);
-		usb_stor_dbg(us, "IsMMC      = %x\n", s->IsMMC);
-		usb_stor_dbg(us, "HiCapacity = %x\n", s->HiCapacity);
-		usb_stor_dbg(us, "HiSpeed    = %x\n", s->HiSpeed);
-		usb_stor_dbg(us, "WtP        = %x\n", s->WtP);
+		usb_stor_dbg(us, "Insert     = %x\n", !!(s & SD_Insert));
+		usb_stor_dbg(us, "Ready      = %x\n", !!(s & SD_Ready));
+		usb_stor_dbg(us, "IsMMC      = %x\n", !!(s & SD_IsMMC));
+		usb_stor_dbg(us, "HiCapacity = %x\n", !!(s & SD_HiCapacity));
+		usb_stor_dbg(us, "HiSpeed    = %x\n", !!(s & SD_HiSpeed));
+		usb_stor_dbg(us, "WtP        = %x\n", !!(s & SD_WtP));
 	} else {
 		usb_stor_dbg(us, "SD Card Not Ready --- %x\n", bbuf[0]);
 		return USB_STOR_TRANSPORT_ERROR;
@@ -2201,14 +2200,14 @@
 
 	misc_reg03 = bbuf[0];
 	if (misc_reg03 & 0x01) {
-		if (!info->SD_Status.Ready) {
+		if (!(info->SD_Status & SD_Ready)) {
 			result = ene_sd_init(us);
 			if (result != USB_STOR_XFER_GOOD)
 				return USB_STOR_TRANSPORT_ERROR;
 		}
 	}
 	if (misc_reg03 & 0x02) {
-		if (!info->MS_Status.Ready) {
+		if (!(info->MS_Status & MS_Ready)) {
 			result = ene_ms_init(us);
 			if (result != USB_STOR_XFER_GOOD)
 				return USB_STOR_TRANSPORT_ERROR;
@@ -2307,14 +2306,14 @@
 
 	/*US_DEBUG(usb_stor_show_command(us, srb)); */
 	scsi_set_resid(srb, 0);
-	if (unlikely(!(info->SD_Status.Ready || info->MS_Status.Ready)))
+	if (unlikely(!(info->SD_Status & SD_Ready) || (info->MS_Status & MS_Ready)))
 		result = ene_init(us);
 	if (result == USB_STOR_XFER_GOOD) {
 		result = USB_STOR_TRANSPORT_ERROR;
-		if (info->SD_Status.Ready)
+		if (info->SD_Status & SD_Ready)
 			result = sd_scsi_irp(us, srb);
 
-		if (info->MS_Status.Ready)
+		if (info->MS_Status & MS_Ready)
 			result = ms_scsi_irp(us, srb);
 	}
 	return result;
@@ -2378,7 +2377,6 @@
 
 static int ene_ub6250_resume(struct usb_interface *iface)
 {
-	u8 tmp = 0;
 	struct us_data *us = usb_get_intfdata(iface);
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *)(us->extra);
 
@@ -2390,17 +2388,16 @@
 	mutex_unlock(&us->dev_mutex);
 
 	info->Power_IsResum = true;
-	/*info->SD_Status.Ready = 0; */
-	info->SD_Status = *(struct SD_STATUS *)&tmp;
-	info->MS_Status = *(struct MS_STATUS *)&tmp;
-	info->SM_Status = *(struct SM_STATUS *)&tmp;
+	/* info->SD_Status &= ~SD_Ready; */
+	info->SD_Status = 0;
+	info->MS_Status = 0;
+	info->SM_Status = 0;
 
 	return 0;
 }
 
 static int ene_ub6250_reset_resume(struct usb_interface *iface)
 {
-	u8 tmp = 0;
 	struct us_data *us = usb_get_intfdata(iface);
 	struct ene_ub6250_info *info = (struct ene_ub6250_info *)(us->extra);
 
@@ -2412,10 +2409,10 @@
 	 * the device
 	 */
 	info->Power_IsResum = true;
-	/*info->SD_Status.Ready = 0; */
-	info->SD_Status = *(struct SD_STATUS *)&tmp;
-	info->MS_Status = *(struct MS_STATUS *)&tmp;
-	info->SM_Status = *(struct SM_STATUS *)&tmp;
+	/* info->SD_Status &= ~SD_Ready; */
+	info->SD_Status = 0;
+	info->MS_Status = 0;
+	info->SM_Status = 0;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/isd200.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/isd200.c
@@ -1105,7 +1105,7 @@
 static int isd200_get_inquiry_data( struct us_data *us )
 {
 	struct isd200_info *info = (struct isd200_info *)us->extra;
-	int retStatus = ISD200_GOOD;
+	int retStatus;
 	u16 *id = info->id;
 
 	usb_stor_dbg(us, "Entering isd200_get_inquiry_data\n");
@@ -1137,6 +1137,13 @@
 				isd200_fix_driveid(id);
 				isd200_dump_driveid(us, id);
 
+				/* Prevent division by 0 in isd200_scsi_to_ata() */
+				if (id[ATA_ID_HEADS] == 0 || id[ATA_ID_SECTORS] == 0) {
+					usb_stor_dbg(us, "   Invalid ATA Identify data\n");
+					retStatus = ISD200_ERROR;
+					goto Done;
+				}
+
 				memset(&info->InquiryData, 0, sizeof(info->InquiryData));
 
 				/* Standard IDE interface only supports disks */
@@ -1202,6 +1209,7 @@
 		}
 	}
 
+ Done:
 	usb_stor_dbg(us, "Leaving isd200_get_inquiry_data %08X\n", retStatus);
 
 	return(retStatus);
@@ -1481,22 +1489,27 @@
 
 static int isd200_Initialization(struct us_data *us)
 {
+	int rc = 0;
+
 	usb_stor_dbg(us, "ISD200 Initialization...\n");
 
 	/* Initialize ISD200 info struct */
 
-	if (isd200_init_info(us) == ISD200_ERROR) {
+	if (isd200_init_info(us) < 0) {
 		usb_stor_dbg(us, "ERROR Initializing ISD200 Info struct\n");
+		rc = -ENOMEM;
 	} else {
 		/* Get device specific data */
 
-		if (isd200_get_inquiry_data(us) != ISD200_GOOD)
+		if (isd200_get_inquiry_data(us) != ISD200_GOOD) {
 			usb_stor_dbg(us, "ISD200 Initialization Failure\n");
-		else
+			rc = -EINVAL;
+		} else {
 			usb_stor_dbg(us, "ISD200 Initialization complete\n");
+		}
 	}
 
-	return 0;
+	return rc;
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/karma.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/karma.c
@@ -174,24 +174,25 @@
 
 static int rio_karma_init(struct us_data *us)
 {
-	int ret = 0;
 	struct karma_data *data = kzalloc(sizeof(struct karma_data), GFP_NOIO);
 
 	if (!data)
-		goto out;
+		return -ENOMEM;
 
 	data->recv = kmalloc(RIO_RECV_LEN, GFP_NOIO);
 	if (!data->recv) {
 		kfree(data);
-		goto out;
+		return -ENOMEM;
 	}
 
 	us->extra = data;
 	us->extra_destructor = rio_karma_destructor;
-	ret = rio_karma_send_command(RIO_ENTER_STORAGE, us);
-	data->in_storage = (ret == 0);
-out:
-	return ret;
+	if (rio_karma_send_command(RIO_ENTER_STORAGE, us))
+		return -EIO;
+
+	data->in_storage = 1;
+
+	return 0;
 }
 
 static struct scsi_host_template karma_host_template;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/realtek_cr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/realtek_cr.c
@@ -41,6 +41,10 @@
 module_param(auto_delink_en, int, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(auto_delink_en, "auto delink mode (0=firmware, 1=software [default])");
 
+static int enable_mmc = 1;
+module_param(enable_mmc, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(enable_mmc, "enable mmc support");
+
 #ifdef CONFIG_REALTEK_AUTOPM
 static int ss_en = 1;
 module_param(ss_en, int, S_IRUGO | S_IWUSR);
@@ -365,7 +369,7 @@
 
 	buf = kmalloc(len, GFP_NOIO);
 	if (buf == NULL)
-		return USB_STOR_TRANSPORT_ERROR;
+		return -ENOMEM;
 
 	usb_stor_dbg(us, "addr = 0x%x, len = %d\n", addr, len);
 
@@ -475,6 +479,27 @@
 	return 0;
 }
 
+static int rts51x_lun_is_mmc_xd(struct us_data *us, u8 lun)
+{
+	struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra);
+
+	if (rts51x_check_status(us, lun))
+		return -EIO;
+
+	usb_stor_dbg(us,"cur_lun = 0x%02X\n", chip->status[lun].cur_lun);
+	usb_stor_dbg(us,"card_type = 0x%02X\n", chip->status[lun].card_type);
+	usb_stor_dbg(us,"detailed_type1= 0x%02X\n", chip->status[lun].detailed_type.detailed_type1);
+	switch (chip->status[lun].card_type) {
+	case 0x4: /* XD */
+		return 1;
+	case 0x2: /* SD/MMC */
+		if (chip->status[lun].detailed_type.detailed_type1 & 0x08)
+			return 1;
+	default:
+		return 0;
+	}
+}
+
 static int enable_oscillator(struct us_data *us)
 {
 	int retval;
@@ -850,6 +875,17 @@
 			chip->proto_handler_backup(srb, us);
 			/* Check whether card is plugged in */
 			if (srb->cmnd[0] == TEST_UNIT_READY) {
+				if (!enable_mmc && rts51x_lun_is_mmc_xd(us, srb->device->lun)) {
+					usb_stor_dbg(us,"%s: lun is mmc/xd\n", __func__);
+					srb->result = SAM_STAT_CHECK_CONDITION;
+					memcpy(srb->sense_buffer,
+							media_not_present,
+							US_SENSE_SIZE);
+					CLR_LUN_READY(chip, srb->device->lun);
+					card_first_show = 1;
+					return;
+				}
+
 				if (srb->result == SAM_STAT_GOOD) {
 					SET_LUN_READY(chip, srb->device->lun);
 					if (card_first_show) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/scsiglue.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/scsiglue.c
@@ -393,7 +393,6 @@
 	}
 
 	/* enqueue the command and wake up the control thread */
-	srb->scsi_done = done;
 	us->srb = srb;
 	complete(&us->cmnd_ready);
 
@@ -407,22 +406,25 @@
  ***********************************************************************/
 
 /* Command timeout and abort */
-static int command_abort(struct scsi_cmnd *srb)
+static int command_abort_matching(struct us_data *us, struct scsi_cmnd *srb_match)
 {
-	struct us_data *us = host_to_us(srb->device->host);
-
-	usb_stor_dbg(us, "%s called\n", __func__);
-
 	/*
 	 * us->srb together with the TIMED_OUT, RESETTING, and ABORTING
 	 * bits are protected by the host lock.
 	 */
 	scsi_lock(us_to_host(us));
 
-	/* Is this command still active? */
-	if (us->srb != srb) {
+	/* is there any active pending command to abort ? */
+	if (!us->srb) {
 		scsi_unlock(us_to_host(us));
 		usb_stor_dbg(us, "-- nothing to abort\n");
+		return SUCCESS;
+	}
+
+	/* Does the command match the passed srb if any ? */
+	if (srb_match && us->srb != srb_match) {
+		scsi_unlock(us_to_host(us));
+		usb_stor_dbg(us, "-- pending command mismatch\n");
 		return FAILED;
 	}
 
@@ -445,6 +447,14 @@
 	return SUCCESS;
 }
 
+static int command_abort(struct scsi_cmnd *srb)
+{
+	struct us_data *us = host_to_us(srb->device->host);
+
+	usb_stor_dbg(us, "%s called\n", __func__);
+	return command_abort_matching(us, srb);
+}
+
 /*
  * This invokes the transport reset mechanism to reset the state of the
  * device
@@ -456,6 +466,9 @@
 
 	usb_stor_dbg(us, "%s called\n", __func__);
 
+	/* abort any pending command before reset */
+	command_abort_matching(us, NULL);
+
 	/* lock the device pointers and do the reset */
 	mutex_lock(&(us->dev_mutex));
 	result = us->transport_reset(us);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/uas-detect.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/uas-detect.h
@@ -116,6 +116,19 @@
 	if (le16_to_cpu(udev->descriptor.idVendor) == 0x0bc2)
 		flags |= US_FL_NO_ATA_1X;
 
+	/*
+	 * RTL9210-based enclosure from HIKSEMI, MD202 reportedly have issues
+	 * with UAS.  This isn't distinguishable with just idVendor and
+	 * idProduct, use manufacturer and product too.
+	 *
+	 * Reported-by: Hongling Zeng <zenghongling@kylinos.cn>
+	 */
+	if (le16_to_cpu(udev->descriptor.idVendor) == 0x0bda &&
+			le16_to_cpu(udev->descriptor.idProduct) == 0x9210 &&
+			(udev->manufacturer && !strcmp(udev->manufacturer, "HIKSEMI")) &&
+			(udev->product && !strcmp(udev->product, "MD202")))
+		flags |= US_FL_IGNORE_UAS;
+
 	usb_stor_adjust_quirks(udev, &flags);
 
 	if (flags & US_FL_IGNORE_UAS) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/uas.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/uas.c
@@ -80,6 +80,8 @@
 static void uas_free_streams(struct uas_dev_info *devinfo);
 static void uas_log_cmd_state(struct scsi_cmnd *cmnd, const char *prefix,
 				int status);
+static struct urb *uas_alloc_cmd_urb(struct uas_dev_info *devinfo, gfp_t gfp,
+					struct scsi_cmnd *cmnd);
 
 /*
  * This driver needs its own workqueue, as we need to control memory allocation.
@@ -113,7 +115,7 @@
 			continue;
 
 		cmnd = devinfo->cmnd[i];
-		cmdinfo = (void *)&cmnd->SCp;
+		cmdinfo = scsi_cmd_priv(cmnd);
 
 		if (!(cmdinfo->state & IS_IN_WORK_LIST))
 			continue;
@@ -139,10 +141,9 @@
 	dev_dbg(&devinfo->intf->dev, "scan complete\n");
 }
 
-static void uas_add_work(struct uas_cmd_info *cmdinfo)
+static void uas_add_work(struct scsi_cmnd *cmnd)
 {
-	struct scsi_pointer *scp = (void *)cmdinfo;
-	struct scsi_cmnd *cmnd = container_of(scp, struct scsi_cmnd, SCp);
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct uas_dev_info *devinfo = cmnd->device->hostdata;
 
 	lockdep_assert_held(&devinfo->lock);
@@ -163,7 +164,7 @@
 			continue;
 
 		cmnd = devinfo->cmnd[i];
-		cmdinfo = (void *)&cmnd->SCp;
+		cmdinfo = scsi_cmd_priv(cmnd);
 		uas_log_cmd_state(cmnd, __func__, 0);
 		/* Sense urbs were killed, clear COMMAND_INFLIGHT manually */
 		cmdinfo->state &= ~COMMAND_INFLIGHT;
@@ -200,15 +201,14 @@
 static void uas_log_cmd_state(struct scsi_cmnd *cmnd, const char *prefix,
 			      int status)
 {
-	struct uas_cmd_info *ci = (void *)&cmnd->SCp;
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *ci = scsi_cmd_priv(cmnd);
 
 	if (status == -ENODEV) /* too late */
 		return;
 
 	scmd_printk(KERN_INFO, cmnd,
 		    "%s %d uas-tag %d inflight:%s%s%s%s%s%s%s%s%s%s%s%s ",
-		    prefix, status, cmdinfo->uas_tag,
+		    prefix, status, ci->uas_tag,
 		    (ci->state & SUBMIT_STATUS_URB)     ? " s-st"  : "",
 		    (ci->state & ALLOC_DATA_IN_URB)     ? " a-in"  : "",
 		    (ci->state & SUBMIT_DATA_IN_URB)    ? " s-in"  : "",
@@ -231,7 +231,7 @@
 	if (!cmnd)
 		return;
 
-	cmdinfo = (void *)&cmnd->SCp;
+	cmdinfo = scsi_cmd_priv(cmnd);
 
 	if (cmdinfo->state & SUBMIT_CMD_URB)
 		usb_free_urb(cmdinfo->cmd_urb);
@@ -245,7 +245,7 @@
 
 static int uas_try_complete(struct scsi_cmnd *cmnd, const char *caller)
 {
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct uas_dev_info *devinfo = (void *)cmnd->device->hostdata;
 
 	lockdep_assert_held(&devinfo->lock);
@@ -256,20 +256,20 @@
 		return -EBUSY;
 	devinfo->cmnd[cmdinfo->uas_tag - 1] = NULL;
 	uas_free_unsubmitted_urbs(cmnd);
-	cmnd->scsi_done(cmnd);
+	scsi_done(cmnd);
 	return 0;
 }
 
 static void uas_xfer_data(struct urb *urb, struct scsi_cmnd *cmnd,
 			  unsigned direction)
 {
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	int err;
 
 	cmdinfo->state |= direction | SUBMIT_STATUS_URB;
 	err = uas_submit_urbs(cmnd, cmnd->device->hostdata);
 	if (err) {
-		uas_add_work(cmdinfo);
+		uas_add_work(cmnd);
 	}
 }
 
@@ -296,18 +296,285 @@
 	return response_code == RC_TMF_SUCCEEDED;
 }
 
+static void dummy_scsi_done(struct scsi_cmnd *cmnd)
+{
+	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_dev_info *devinfo = (void *)cmnd->device->hostdata;
+
+	devinfo->cmnd[cmdinfo->uas_tag - 1] = NULL;
+	kfree(scsi_cmd_to_rq(cmnd));
+	kfree(cmnd);
+}
+
+static void uas_workaround_cmplt(struct urb *urb)
+{
+	struct scsi_cmnd *cmnd;
+	struct uas_cmd_info *cmdinfo;
+
+	if ((urb->context != NULL) && (urb->status == 0)) {
+		cmnd = urb->context;
+		cmdinfo = (struct uas_cmd_info *)&cmnd->SCp;
+
+		if (cmdinfo->data_in_urb != urb)
+			cmnd->scsi_done(cmnd);
+	}
+
+	usb_free_urb(urb);
+}
+
+static struct urb *uas_workaround_cmnd(struct uas_dev_info *devinfo, gfp_t gfp,
+				       struct scsi_cmnd *cmnd)
+{
+	struct scsi_device *sdev = cmnd->device;
+	struct urb *urb;
+	int err;
+
+	urb = uas_alloc_cmd_urb(devinfo, gfp, cmnd);
+	if (!urb) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate cmnd URB\n", __func__);
+		return NULL;
+	}
+
+	err = usb_submit_urb(urb, gfp);
+	if (err) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to submit cmd, err=%d\n", __func__, err);
+		goto free;
+	}
+	usb_anchor_urb(urb, &devinfo->cmd_urbs);
+	return urb;
+
+free:
+	usb_free_urb(urb);
+	return NULL;
+
+}
+
+static struct urb *uas_workaround_data(struct uas_dev_info *devinfo, gfp_t gfp,
+				       struct scsi_cmnd *cmnd)
+{
+	struct scsi_device *sdev = cmnd->device;
+	struct usb_device *udev = devinfo->udev;
+	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct urb *urb = usb_alloc_urb(0, gfp);
+	struct scsi_data_buffer *sdb = NULL;
+	void *temp_buf;
+	unsigned int pipe;
+	int err;
+
+	if (!urb) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate URB\n", __func__);
+		return NULL;
+	}
+
+	cmdinfo->data_in_urb = urb;
+	sdb = &cmnd->sdb;
+	pipe = devinfo->data_in_pipe;
+	temp_buf = kzalloc(sdb->length, GFP_ATOMIC);
+	if (!temp_buf) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate memory\n", __func__);
+		goto free;
+	}
+
+	usb_fill_bulk_urb(urb, udev, pipe, temp_buf, sdb->length,
+			  uas_workaround_cmplt, cmnd);
+	if (devinfo->use_streams)
+		urb->stream_id = cmdinfo->uas_tag;
+	urb->transfer_flags |= URB_FREE_BUFFER;
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+	if (err) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to submit Data In urb, err = %d\n",
+			__func__, err);
+		goto free;
+	}
+
+	usb_anchor_urb(urb, &devinfo->data_urbs);
+	return urb;
+
+free:
+	usb_free_urb(urb);
+	return NULL;
+}
+
+static struct urb *uas_workaround_sense(struct uas_dev_info *devinfo, gfp_t gfp,
+				       struct scsi_cmnd *cmnd)
+{
+	struct scsi_device *sdev = cmnd->device;
+	struct usb_device *udev = devinfo->udev;
+	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct urb *urb = usb_alloc_urb(0, gfp);
+	struct sense_iu *iu;
+	int err;
+
+	if (!urb) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate URB\n", __func__);
+		return NULL;
+	}
+
+	iu = kzalloc(sizeof(*iu), gfp);
+	if (!iu) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate memory for sense_iu\n",
+			__func__);
+		goto free;
+	}
+
+	usb_fill_bulk_urb(urb, udev, devinfo->status_pipe, iu, sizeof(*iu),
+			  uas_workaround_cmplt, cmnd);
+	if (devinfo->use_streams)
+		urb->stream_id = cmdinfo->uas_tag;
+	urb->transfer_flags |= URB_FREE_BUFFER;
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+	if (err) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to submit Sense urb, err = %d\n",
+			__func__, err);
+		goto free;
+	}
+	usb_anchor_urb(urb, &devinfo->sense_urbs);
+	return urb;
+
+free:
+	usb_free_urb(urb);
+	return NULL;
+}
+
+/*
+ * This function is called only if the DATA IN stream timer expired, which
+ * means xhci host controller has failed to process the TRB's present in the
+ * stream ring. As a part of recovery sequence, this function re-submits the
+ * previous stopped urb on which xhci failed to process data and along with
+ * that urb it prepares & submits sense, data and cmnd urb with scsi command
+ * set to standard inquiry request containing the next free stream id tag.
+ * Doing so will make the xhci start processing the previous stopped urb
+ * along with the urb that has standard inquiry scsi command.
+ */
+static int uas_workaround(struct urb *urb)
+{
+	struct scsi_cmnd *cmnd = urb->context;
+	struct scsi_device *sdev = cmnd->device;
+	struct uas_dev_info *devinfo = (void *)cmnd->device->hostdata;
+	struct scsi_cmnd *temp_cmnd;
+	struct uas_cmd_info *temp_cmdinfo;
+	struct urb *sense_urb, *data_urb, *cmnd_urb;
+	struct request *temp_request;
+	unsigned int idx;
+	int err;
+	char inquiry[16] = { 0x12, 0x0, 0x0, 0x0, 0x10, 0x0, 0x0, 0x0,
+				0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0 };
+
+
+	/* Find a free uas-tag */
+	for (idx = 0; idx < devinfo->qdepth; idx++) {
+		if (!devinfo->cmnd[idx])
+			break;
+	}
+
+	if (idx == devinfo->qdepth) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to find free tag\n", __func__);
+		err = -EINVAL;
+		goto free;
+	}
+
+	/* Create a scsi_cmnd and send dummy inquiry data on the next
+	 * available tag
+	 */
+	temp_cmnd = kzalloc(sizeof(struct scsi_cmnd), GFP_ATOMIC);
+	if (!temp_cmnd) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate memory for scsi_cmnd\n",
+			__func__);
+		err = -ENOMEM;
+		goto free;
+	}
+
+	temp_request = kzalloc(sizeof(struct request), GFP_ATOMIC);
+	if (!temp_cmnd) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: Failed to allocate memory for request\n",
+			__func__);
+		err = -ENOMEM;
+		goto free;
+	}
+
+	temp_cmnd->device = cmnd->device;
+	temp_cmnd->cmnd = inquiry;
+	temp_cmnd->cmd_len = 16;
+	temp_cmnd->sdb.length = 0x10;
+	temp_cmnd->scsi_done = dummy_scsi_done;
+	temp_request->tag = idx;
+
+	temp_cmdinfo = (struct uas_cmd_info *)&temp_cmnd->SCp;
+	memset(temp_cmdinfo, 0, sizeof(struct uas_cmd_info));
+
+	temp_cmdinfo->uas_tag = idx + 1;
+	devinfo->cmnd[idx] = temp_cmnd;
+
+	/* Submit previously stopped URB first */
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+	if (err) {
+		shost_printk(KERN_INFO, sdev->host,
+			"%s: submit err %d\n", __func__, err);
+		kfree(temp_cmnd);
+		kfree(temp_request);
+		goto free;
+	}
+	usb_anchor_urb(urb, &devinfo->data_urbs);
+
+	/* Allocate and submit SENSE urb for next available tag */
+	sense_urb = uas_workaround_sense(devinfo, GFP_ATOMIC, temp_cmnd);
+	if (!sense_urb) {
+		kfree(temp_request);
+		kfree(temp_cmnd);
+		goto free;
+	}
+
+	/* Allocate and submit DATA IN urb for next available tag */
+	data_urb = uas_workaround_data(devinfo, GFP_ATOMIC, temp_cmnd);
+	if (!data_urb) {
+		/* Kill previously allocated sense urb */
+		sense_urb->context = NULL;
+		usb_kill_urb(sense_urb);
+		usb_put_urb(sense_urb);
+		kfree(temp_request);
+		kfree(temp_cmnd);
+		goto free;
+	}
+
+	/* Allocate and submit CMND urb with dummy inquiry data */
+	cmnd_urb = uas_workaround_cmnd(devinfo, GFP_ATOMIC, temp_cmnd);
+	if (!cmnd_urb) {
+		/* Kill previously allocated data urb */
+		data_urb->context = NULL;
+		usb_kill_urb(data_urb);
+		usb_put_urb(data_urb);
+		kfree(temp_request);
+		kfree(temp_cmnd);
+	}
+
+free:
+	return err;
+}
+
 static void uas_stat_cmplt(struct urb *urb)
 {
 	struct iu *iu = urb->transfer_buffer;
-	struct Scsi_Host *shost = urb->context;
-	struct uas_dev_info *devinfo = (struct uas_dev_info *)shost->hostdata;
+	struct scsi_cmnd *cmnd = (struct scsi_cmnd *)urb->context;
+	struct uas_dev_info *devinfo =
+				(struct uas_dev_info *)cmnd->device->hostdata;
 	struct urb *data_in_urb = NULL;
 	struct urb *data_out_urb = NULL;
-	struct scsi_cmnd *cmnd;
 	struct uas_cmd_info *cmdinfo;
 	unsigned long flags;
 	unsigned int idx;
 	int status = urb->status;
+	int err;
 	bool success;
 
 	spin_lock_irqsave(&devinfo->lock, flags);
@@ -316,6 +583,21 @@
 		goto out;
 
 	if (status) {
+		if (status  == -EAGAIN) {
+			/* We get here only if the xhci stream timer expires,
+			 * call uas_workaround() with this urb as argument.
+			 */
+			err = uas_workaround(urb);
+			if (err != 0) {
+				dev_err(&urb->dev->dev,
+					"%s: uas_workaround() failed, err=%d\n",
+					__func__, err);
+				goto out;
+			}
+			spin_unlock_irqrestore(&devinfo->lock, flags);
+			return;
+		}
+
 		if (status != -ENOENT && status != -ECONNRESET && status != -ESHUTDOWN)
 			dev_err(&urb->dev->dev, "stat urb: status %d\n", status);
 		goto out;
@@ -329,7 +611,7 @@
 	}
 
 	cmnd = devinfo->cmnd[idx];
-	cmdinfo = (void *)&cmnd->SCp;
+	cmdinfo = scsi_cmd_priv(cmnd);
 
 	if (!(cmdinfo->state & COMMAND_INFLIGHT)) {
 		uas_log_cmd_state(cmnd, "unexpected status cmplt", 0);
@@ -394,14 +676,31 @@
 static void uas_data_cmplt(struct urb *urb)
 {
 	struct scsi_cmnd *cmnd = urb->context;
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct uas_dev_info *devinfo = (void *)cmnd->device->hostdata;
 	struct scsi_data_buffer *sdb = &cmnd->sdb;
 	unsigned long flags;
+	int err;
 	int status = urb->status;
 
 	spin_lock_irqsave(&devinfo->lock, flags);
 
+	if ((status  == -EAGAIN) && (!devinfo->resetting) &&
+					(cmdinfo->data_in_urb == urb)) {
+		/* We get here only if the xhci stream timer expires,
+		 * call uas_workaround() with this urb as argument.
+		 */
+		err = uas_workaround(urb);
+		if (err != 0) {
+			dev_err(&urb->dev->dev,
+				"%s: uas_workaround() failed, err=%d\n",
+				__func__, err);
+			goto out;
+		}
+		spin_unlock_irqrestore(&devinfo->lock, flags);
+		return;
+	}
+
 	if (cmdinfo->data_in_urb == urb) {
 		cmdinfo->state &= ~DATA_IN_URB_INFLIGHT;
 		cmdinfo->data_in_urb = NULL;
@@ -424,6 +723,7 @@
 			uas_log_cmd_state(cmnd, "data cmplt err", status);
 		/* error: no data transfered */
 		scsi_set_resid(cmnd, sdb->length);
+		set_host_byte(cmnd, DID_ERROR);
 	} else {
 		scsi_set_resid(cmnd, sdb->length - urb->actual_length);
 	}
@@ -446,7 +746,7 @@
 				      enum dma_data_direction dir)
 {
 	struct usb_device *udev = devinfo->udev;
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct urb *urb = usb_alloc_urb(0, gfp);
 	struct scsi_data_buffer *sdb = &cmnd->sdb;
 	unsigned int pipe = (dir == DMA_FROM_DEVICE)
@@ -468,7 +768,7 @@
 				       struct scsi_cmnd *cmnd)
 {
 	struct usb_device *udev = devinfo->udev;
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct urb *urb = usb_alloc_urb(0, gfp);
 	struct sense_iu *iu;
 
@@ -480,7 +780,7 @@
 		goto free;
 
 	usb_fill_bulk_urb(urb, udev, devinfo->status_pipe, iu, sizeof(*iu),
-			  uas_stat_cmplt, cmnd->device->host);
+			  uas_stat_cmplt, cmnd);
 	if (devinfo->use_streams)
 		urb->stream_id = cmdinfo->uas_tag;
 	urb->transfer_flags |= URB_FREE_BUFFER;
@@ -496,7 +796,7 @@
 {
 	struct usb_device *udev = devinfo->udev;
 	struct scsi_device *sdev = cmnd->device;
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct urb *urb = usb_alloc_urb(0, gfp);
 	struct command_iu *iu;
 	int len;
@@ -535,7 +835,7 @@
  * daft to me.
  */
 
-static struct urb *uas_submit_sense_urb(struct scsi_cmnd *cmnd, gfp_t gfp)
+static int uas_submit_sense_urb(struct scsi_cmnd *cmnd, gfp_t gfp)
 {
 	struct uas_dev_info *devinfo = cmnd->device->hostdata;
 	struct urb *urb;
@@ -543,30 +843,28 @@
 
 	urb = uas_alloc_sense_urb(devinfo, gfp, cmnd);
 	if (!urb)
-		return NULL;
+		return -ENOMEM;
 	usb_anchor_urb(urb, &devinfo->sense_urbs);
 	err = usb_submit_urb(urb, gfp);
 	if (err) {
 		usb_unanchor_urb(urb);
 		uas_log_cmd_state(cmnd, "sense submit err", err);
 		usb_free_urb(urb);
-		return NULL;
 	}
-	return urb;
+	return err;
 }
 
 static int uas_submit_urbs(struct scsi_cmnd *cmnd,
 			   struct uas_dev_info *devinfo)
 {
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
-	struct urb *urb;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	int err;
 
 	lockdep_assert_held(&devinfo->lock);
 	if (cmdinfo->state & SUBMIT_STATUS_URB) {
-		urb = uas_submit_sense_urb(cmnd, GFP_ATOMIC);
-		if (!urb)
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+		err = uas_submit_sense_urb(cmnd, GFP_ATOMIC);
+		if (err)
+			return err;
 		cmdinfo->state &= ~SUBMIT_STATUS_URB;
 	}
 
@@ -574,7 +872,7 @@
 		cmdinfo->data_in_urb = uas_alloc_data_urb(devinfo, GFP_ATOMIC,
 							cmnd, DMA_FROM_DEVICE);
 		if (!cmdinfo->data_in_urb)
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+			return -ENOMEM;
 		cmdinfo->state &= ~ALLOC_DATA_IN_URB;
 	}
 
@@ -584,7 +882,7 @@
 		if (err) {
 			usb_unanchor_urb(cmdinfo->data_in_urb);
 			uas_log_cmd_state(cmnd, "data in submit err", err);
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+			return err;
 		}
 		cmdinfo->state &= ~SUBMIT_DATA_IN_URB;
 		cmdinfo->state |= DATA_IN_URB_INFLIGHT;
@@ -594,7 +892,7 @@
 		cmdinfo->data_out_urb = uas_alloc_data_urb(devinfo, GFP_ATOMIC,
 							cmnd, DMA_TO_DEVICE);
 		if (!cmdinfo->data_out_urb)
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+			return -ENOMEM;
 		cmdinfo->state &= ~ALLOC_DATA_OUT_URB;
 	}
 
@@ -604,7 +902,7 @@
 		if (err) {
 			usb_unanchor_urb(cmdinfo->data_out_urb);
 			uas_log_cmd_state(cmnd, "data out submit err", err);
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+			return err;
 		}
 		cmdinfo->state &= ~SUBMIT_DATA_OUT_URB;
 		cmdinfo->state |= DATA_OUT_URB_INFLIGHT;
@@ -613,7 +911,7 @@
 	if (cmdinfo->state & ALLOC_CMD_URB) {
 		cmdinfo->cmd_urb = uas_alloc_cmd_urb(devinfo, GFP_ATOMIC, cmnd);
 		if (!cmdinfo->cmd_urb)
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+			return -ENOMEM;
 		cmdinfo->state &= ~ALLOC_CMD_URB;
 	}
 
@@ -623,7 +921,7 @@
 		if (err) {
 			usb_unanchor_urb(cmdinfo->cmd_urb);
 			uas_log_cmd_state(cmnd, "cmd submit err", err);
-			return SCSI_MLQUEUE_DEVICE_BUSY;
+			return err;
 		}
 		cmdinfo->cmd_urb = NULL;
 		cmdinfo->state &= ~SUBMIT_CMD_URB;
@@ -638,12 +936,10 @@
 {
 	struct scsi_device *sdev = cmnd->device;
 	struct uas_dev_info *devinfo = sdev->hostdata;
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	unsigned long flags;
 	int idx, err;
 
-	BUILD_BUG_ON(sizeof(struct uas_cmd_info) > sizeof(struct scsi_pointer));
-
 	/* Re-check scsi_block_requests now that we've the host-lock */
 	if (cmnd->device->host->host_self_blocked)
 		return SCSI_MLQUEUE_DEVICE_BUSY;
@@ -653,7 +949,7 @@
 		memcpy(cmnd->sense_buffer, usb_stor_sense_invalidCDB,
 		       sizeof(usb_stor_sense_invalidCDB));
 		cmnd->result = SAM_STAT_CHECK_CONDITION;
-		cmnd->scsi_done(cmnd);
+		scsi_done(cmnd);
 		return 0;
 	}
 
@@ -661,7 +957,7 @@
 
 	if (devinfo->resetting) {
 		set_host_byte(cmnd, DID_ERROR);
-		cmnd->scsi_done(cmnd);
+		scsi_done(cmnd);
 		goto zombie;
 	}
 
@@ -675,8 +971,6 @@
 		return SCSI_MLQUEUE_DEVICE_BUSY;
 	}
 
-	cmnd->scsi_done = done;
-
 	memset(cmdinfo, 0, sizeof(*cmdinfo));
 	cmdinfo->uas_tag = idx + 1; /* uas-tag == usb-stream-id, so 1 based */
 	cmdinfo->state = SUBMIT_STATUS_URB | ALLOC_CMD_URB | SUBMIT_CMD_URB;
@@ -705,8 +999,8 @@
 	 * of queueing, no matter how fatal the error
 	 */
 	if (err == -ENODEV) {
-		set_host_byte(cmnd, DID_ERROR);
-		cmnd->scsi_done(cmnd);
+		set_host_byte(cmnd, DID_NO_CONNECT);
+		scsi_done(cmnd);
 		goto zombie;
 	}
 	if (err) {
@@ -715,7 +1009,7 @@
 			spin_unlock_irqrestore(&devinfo->lock, flags);
 			return SCSI_MLQUEUE_DEVICE_BUSY;
 		}
-		uas_add_work(cmdinfo);
+		uas_add_work(cmnd);
 	}
 
 	devinfo->cmnd[idx] = cmnd;
@@ -733,7 +1027,7 @@
  */
 static int uas_eh_abort_handler(struct scsi_cmnd *cmnd)
 {
-	struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp;
+	struct uas_cmd_info *cmdinfo = scsi_cmd_priv(cmnd);
 	struct uas_dev_info *devinfo = (void *)cmnd->device->hostdata;
 	struct urb *data_in_urb = NULL;
 	struct urb *data_out_urb = NULL;
@@ -913,6 +1207,7 @@
 	.this_id = -1,
 	.skip_settle_delay = 1,
 	.dma_boundary = PAGE_SIZE - 1,
+	.cmd_size = sizeof(struct uas_cmd_info),
 };
 
 #define UNUSUAL_DEV(id_vendor, id_product, bcdDeviceMin, bcdDeviceMax, \
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/unusual_cypress.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/unusual_cypress.h
@@ -19,7 +19,7 @@
 		"Cypress ISD-300LP",
 		USB_SC_CYP_ATACB, USB_PR_DEVICE, NULL, 0),
 
-UNUSUAL_DEV( 0x14cd, 0x6116, 0x0160, 0x0160,
+UNUSUAL_DEV( 0x14cd, 0x6116, 0x0150, 0x0160,
 		"Super Top",
 		"USB 2.0  SATA BRIDGE",
 		USB_SC_CYP_ATACB, USB_PR_DEVICE, NULL, 0),
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/unusual_devs.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/unusual_devs.h
@@ -255,6 +255,13 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_MAX_SECTORS_64 ),
 
+/* Added by Lubomir Rintel <lkundrak@v3.sk>, a very fine chap */
+UNUSUAL_DEV(  0x0421, 0x06c2, 0x0000, 0x0406,
+		"Nokia",
+		"Nokia 208",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_MAX_SECTORS_64 ),
+
 #ifdef NO_SDDR09
 UNUSUAL_DEV(  0x0436, 0x0005, 0x0100, 0x0100,
 		"Microtech",
@@ -407,6 +414,16 @@
 		USB_SC_SCSI, USB_PR_BULK, NULL, US_FL_SINGLE_LUN),
 
 /*
+ * Reported by James Buren <braewoods+lkml@braewoods.net>
+ * Virtual ISOs cannot be remounted if ejected while the device is locked
+ * Disable locking to mimic Windows behavior that bypasses the issue
+ */
+UNUSUAL_DEV(  0x04c5, 0x2028, 0x0001, 0x0001,
+		"iODD",
+		"2531/2541",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NOT_LOCKABLE),
+
+/*
  * Not sure who reported this originally but
  * Pavel Machek <pavel@ucw.cz> reported that the extra US_FL_SINGLE_LUN
  * flag be added */
@@ -1265,12 +1282,6 @@
 		USB_SC_RBC, USB_PR_BULK, NULL,
 		0 ),
 
-UNUSUAL_DEV(0x090c, 0x1000, 0x1100, 0x1100,
-		"Samsung",
-		"Flash Drive FIT",
-		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
-		US_FL_MAX_SECTORS_64),
-
 /* aeb */
 UNUSUAL_DEV( 0x090c, 0x1132, 0x0000, 0xffff,
 		"Feiya",
@@ -1344,6 +1355,13 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, option_ms_init,
 		0),
 
+/* Reported by Timo Aaltonen <tjaalton@ubuntu.com> */
+UNUSUAL_DEV( 0x0af0, 0x7011, 0x0000, 0x9999,
+		"Option",
+		"Mass Storage",
+		USB_SC_DEVICE, USB_PR_DEVICE, option_ms_init,
+		0 ),
+
 /*
  * Reported by F. Aben <f.aben@option.com>
  * This device (wrongly) has a vendor-specific device descriptor.
@@ -2284,6 +2302,13 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_BULK_IGNORE_TAG | US_FL_MAX_SECTORS_64 ),
 
+/* Reported by Witold Lipieta <witold.lipieta@thaumatec.com> */
+UNUSUAL_DEV( 0x1fc9, 0x0117, 0x0100, 0x0100,
+		"NXP Semiconductors",
+		"PN7462AU",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_IGNORE_RESIDUE ),
+
 /* Supplied with some Castlewood ORB removable drives */
 UNUSUAL_DEV(  0x2027, 0xa001, 0x0000, 0x9999,
 		"Double-H Technology",
@@ -2291,6 +2316,16 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, usb_stor_euscsi_init,
 		US_FL_SCM_MULT_TARG ),
 
+/*
+ * Reported by DocMAX <mail@vacharakis.de>
+ * and Thomas Weißschuh <linux@weissschuh.net>
+ */
+UNUSUAL_DEV( 0x2109, 0x0715, 0x9999, 0x9999,
+		"VIA Labs, Inc.",
+		"VL817 SATA Bridge",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_IGNORE_UAS),
+
 UNUSUAL_DEV( 0x2116, 0x0320, 0x0001, 0x0001,
 		"ST",
 		"2A",
@@ -2391,6 +2426,17 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_NOT_LOCKABLE),
 
+/*
+ * Reported by Icenowy Zheng <uwu@icenowy.me>
+ * This is an interface for vendor-specific cryptic commands instead
+ * of real USB storage device.
+ */
+UNUSUAL_DEV(  0xe5b7, 0x0811, 0x0100, 0x0100,
+		"ZhuHai JieLi Technology",
+		"JieLi BR21",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_IGNORE_DEVICE),
+
 /* Reported by Andrew Simmons <andrew.simmons@gmail.com> */
 UNUSUAL_DEV(  0xed06, 0x4500, 0x0001, 0x0001,
 		"DataStor",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/unusual_uas.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/unusual_uas.h
@@ -52,6 +52,13 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_NO_REPORT_OPCODES | US_FL_NO_SAME),
 
+/* Reported-by: Hongling Zeng <zenghongling@kylinos.cn> */
+UNUSUAL_DEV(0x090c, 0x2000, 0x0000, 0x9999,
+		"Hiksemi",
+		"External HDD",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_IGNORE_UAS),
+
 /*
  * Apricorn USB3 dongle sometimes returns "USBSUSBSUSBS" in response to SCSI
  * commands in UAS mode.  Observed with the 1.28 firmware; are there others?
@@ -62,6 +69,19 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_IGNORE_UAS),
 
+/* Reported-by: Tom Hu <huxiaoying@kylinos.cn> */
+UNUSUAL_DEV(0x0b05, 0x1932, 0x0000, 0x9999,
+		"ASUS",
+		"External HDD",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_IGNORE_UAS),
+
+UNUSUAL_DEV(0x0525, 0xa4a5, 0x0000, 0x9999,
+	    "Netchip",
+		"Target Product",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_NO_ATA_1X),
+
 /* Reported-by: David Webb <djw@noc.ac.uk> */
 UNUSUAL_DEV(0x0bc2, 0x331a, 0x0000, 0x9999,
 		"Seagate",
@@ -97,6 +117,13 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_BROKEN_FUA),
 
+/* Reported by: Yaroslav Furman <yaro330@gmail.com> */
+UNUSUAL_DEV(0x152d, 0x0583, 0x0000, 0x9999,
+		"JMicron",
+		"JMS583Gen 2",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_NO_REPORT_OPCODES),
+
 /* Reported-by: Thinh Nguyen <thinhn@synopsys.com> */
 UNUSUAL_DEV(0x154b, 0xf00b, 0x0000, 0x9999,
 		"PNY",
@@ -111,6 +138,13 @@
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_NO_ATA_1X),
 
+/* Reported-by: Hongling Zeng <zenghongling@kylinos.cn> */
+UNUSUAL_DEV(0x17ef, 0x3899, 0x0000, 0x9999,
+		"Thinkplus",
+		"External HDD",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_IGNORE_UAS),
+
 /* Reported-by: Hans de Goede <hdegoede@redhat.com> */
 UNUSUAL_DEV(0x2109, 0x0711, 0x0000, 0x9999,
 		"VIA",
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/storage/usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/storage/usb.c
@@ -388,7 +388,7 @@
 		if (srb->result == DID_ABORT << 16) {
 SkipForAbort:
 			usb_stor_dbg(us, "scsi command aborted\n");
-			srb = NULL;	/* Don't call srb->scsi_done() */
+			srb = NULL;	/* Don't call scsi_done() */
 		}
 
 		/*
@@ -417,7 +417,7 @@
 		if (srb) {
 			usb_stor_dbg(us, "scsi cmd done, result=0x%x\n",
 					srb->result);
-			srb->scsi_done(srb);
+			scsi_done(srb);
 		}
 	} /* for (;;) */
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/Kconfig
@@ -65,9 +65,9 @@
 
 config TYPEC_STUSB160X
 	tristate "STMicroelectronics STUSB160x Type-C controller driver"
-	depends on I2C
-	depends on REGMAP_I2C
 	depends on USB_ROLE_SWITCH || !USB_ROLE_SWITCH
+	depends on I2C
+	select REGMAP_I2C
 	help
 	  Say Y or M here if your system has STMicroelectronics STUSB160x
 	  Type-C port controller.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/altmodes/displayport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/altmodes/displayport.c
@@ -88,8 +88,8 @@
 	case DP_STATUS_CON_UFP_D:
 	case DP_STATUS_CON_BOTH: /* NOTE: First acting as DP source */
 		conf |= DP_CONF_UFP_U_AS_UFP_D;
-		pin_assign = DP_CAP_DFP_D_PIN_ASSIGN(dp->alt->vdo) &
-			     DP_CAP_UFP_D_PIN_ASSIGN(dp->port->vdo);
+		pin_assign = DP_CAP_PIN_ASSIGN_UFP_D(dp->alt->vdo) &
+				 DP_CAP_PIN_ASSIGN_DFP_D(dp->port->vdo);
 		break;
 	default:
 		break;
@@ -101,8 +101,12 @@
 		if (dp->data.status & DP_STATUS_PREFER_MULTI_FUNC &&
 		    pin_assign & DP_PIN_ASSIGN_MULTI_FUNC_MASK)
 			pin_assign &= DP_PIN_ASSIGN_MULTI_FUNC_MASK;
-		else if (pin_assign & DP_PIN_ASSIGN_DP_ONLY_MASK)
+		else if (pin_assign & DP_PIN_ASSIGN_DP_ONLY_MASK) {
 			pin_assign &= DP_PIN_ASSIGN_DP_ONLY_MASK;
+			/* Default to pin assign C if available */
+			if (pin_assign & BIT(DP_PIN_ASSIGN_C))
+				pin_assign = BIT(DP_PIN_ASSIGN_C);
+		}
 
 		if (!pin_assign)
 			return -EINVAL;
@@ -418,6 +422,18 @@
 	[DP_PIN_ASSIGN_F] = "F",
 };
 
+/*
+ * Helper function to extract a peripheral's currently supported
+ * Pin Assignments from its DisplayPort alternate mode state.
+ */
+static u8 get_current_pin_assignments(struct dp_altmode *dp)
+{
+	if (DP_CONF_CURRENTLY(dp->data.conf) == DP_CONF_DFP_D)
+		return DP_CAP_PIN_ASSIGN_DFP_D(dp->alt->vdo);
+	else
+		return DP_CAP_PIN_ASSIGN_UFP_D(dp->alt->vdo);
+}
+
 static ssize_t
 pin_assignment_store(struct device *dev, struct device_attribute *attr,
 		     const char *buf, size_t size)
@@ -444,10 +460,7 @@
 		goto out_unlock;
 	}
 
-	if (DP_CONF_CURRENTLY(dp->data.conf) == DP_CONF_DFP_D)
-		assignments = DP_CAP_UFP_D_PIN_ASSIGN(dp->alt->vdo);
-	else
-		assignments = DP_CAP_DFP_D_PIN_ASSIGN(dp->alt->vdo);
+	assignments = get_current_pin_assignments(dp);
 
 	if (!(DP_CONF_GET_PIN_ASSIGN(conf) & assignments)) {
 		ret = -EINVAL;
@@ -484,10 +497,7 @@
 
 	cur = get_count_order(DP_CONF_GET_PIN_ASSIGN(dp->data.conf));
 
-	if (DP_CONF_CURRENTLY(dp->data.conf) == DP_CONF_DFP_D)
-		assignments = DP_CAP_UFP_D_PIN_ASSIGN(dp->alt->vdo);
-	else
-		assignments = DP_CAP_DFP_D_PIN_ASSIGN(dp->alt->vdo);
+	assignments = get_current_pin_assignments(dp);
 
 	for (i = 0; assignments; assignments >>= 1, i++) {
 		if (assignments & 1) {
@@ -502,6 +512,10 @@
 
 	mutex_unlock(&dp->lock);
 
+	/* get_current_pin_assignments can return 0 when no matching pin assignments are found */
+	if (len == 0)
+		len++;
+
 	buf[len - 1] = '\n';
 	return len;
 }
@@ -527,10 +541,10 @@
 	/* FIXME: Port can only be DFP_U. */
 
 	/* Make sure we have compatiple pin configurations */
-	if (!(DP_CAP_DFP_D_PIN_ASSIGN(port->vdo) &
-	      DP_CAP_UFP_D_PIN_ASSIGN(alt->vdo)) &&
-	    !(DP_CAP_UFP_D_PIN_ASSIGN(port->vdo) &
-	      DP_CAP_DFP_D_PIN_ASSIGN(alt->vdo)))
+	if (!(DP_CAP_PIN_ASSIGN_DFP_D(port->vdo) &
+	      DP_CAP_PIN_ASSIGN_UFP_D(alt->vdo)) &&
+	    !(DP_CAP_PIN_ASSIGN_UFP_D(port->vdo) &
+	      DP_CAP_PIN_ASSIGN_DFP_D(alt->vdo)))
 		return -ENODEV;
 
 	ret = sysfs_create_group(&alt->dev.kobj, &dp_altmode_group);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/bus.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/bus.c
@@ -134,7 +134,7 @@
 	if (!adev || !adev->active)
 		return 0;
 
-	if (!pdev->ops || !pdev->ops->enter)
+	if (!pdev->ops || !pdev->ops->exit)
 		return -EOPNOTSUPP;
 
 	/* Moving to USB Safe State */
@@ -154,12 +154,20 @@
  *
  * Notifies the partner of @adev about Attention command.
  */
-void typec_altmode_attention(struct typec_altmode *adev, u32 vdo)
+int typec_altmode_attention(struct typec_altmode *adev, u32 vdo)
 {
-	struct typec_altmode *pdev = &to_altmode(adev)->partner->adev;
+	struct altmode *partner = to_altmode(adev)->partner;
+	struct typec_altmode *pdev;
+
+	if (!partner)
+		return -ENODEV;
+
+	pdev = &partner->adev;
 
 	if (pdev->ops && pdev->ops->attention)
 		pdev->ops->attention(pdev, vdo);
+
+	return 0;
 }
 EXPORT_SYMBOL_GPL(typec_altmode_attention);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/class.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/class.c
@@ -261,11 +261,13 @@
 {
 	struct altmode *partner = altmode->partner;
 	struct typec_altmode *adev;
+	struct typec_altmode *partner_adev;
 
 	if (!partner)
 		return;
 
-	adev = &partner->adev;
+	adev = &altmode->adev;
+	partner_adev = &partner->adev;
 
 	if (is_typec_plug(adev->dev.parent)) {
 		struct typec_plug *plug = to_typec_plug(adev->dev.parent);
@@ -274,7 +276,7 @@
 	} else {
 		partner->partner = NULL;
 	}
-	put_device(&adev->dev);
+	put_device(&partner_adev->dev);
 }
 
 /**
@@ -495,9 +497,11 @@
 {
 	struct altmode *alt = to_altmode(to_typec_altmode(dev));
 
-	typec_altmode_put_partner(alt);
+	if (!is_typec_port(dev->parent))
+		typec_altmode_put_partner(alt);
 
 	altmode_id_remove(alt->adev.dev.parent, alt->id);
+	put_device(alt->adev.dev.parent);
 	kfree(alt);
 }
 
@@ -547,6 +551,8 @@
 	alt->adev.dev.type = &typec_altmode_dev_type;
 	dev_set_name(&alt->adev.dev, "%s.%u", dev_name(parent), id);
 
+	get_device(alt->adev.dev.parent);
+
 	/* Link partners and plugs with the ports */
 	if (!is_port)
 		typec_altmode_set_partner(alt);
@@ -1718,6 +1724,7 @@
 			partner->usb_pd = 1;
 			sysfs_notify(&partner_dev->kobj, NULL,
 				     "supports_usb_power_delivery");
+			kobject_uevent(&partner_dev->kobj, KOBJ_CHANGE);
 		}
 		put_device(partner_dev);
 	}
@@ -1894,6 +1901,49 @@
 }
 EXPORT_SYMBOL_GPL(typec_get_drvdata);
 
+int typec_get_fw_cap(struct typec_capability *cap,
+		     struct fwnode_handle *fwnode)
+{
+	const char *cap_str;
+	int ret;
+
+	cap->fwnode = fwnode;
+
+	ret = fwnode_property_read_string(fwnode, "power-role", &cap_str);
+	if (ret < 0)
+		return ret;
+
+	ret = typec_find_port_power_role(cap_str);
+	if (ret < 0)
+		return ret;
+	cap->type = ret;
+
+	/* USB data support is optional */
+	ret = fwnode_property_read_string(fwnode, "data-role", &cap_str);
+	if (ret == 0) {
+		ret = typec_find_port_data_role(cap_str);
+		if (ret < 0)
+			return ret;
+		cap->data = ret;
+	}
+
+	/* Get the preferred power role for a DRP */
+	if (cap->type == TYPEC_PORT_DRP) {
+		cap->prefer_role = TYPEC_NO_PREFERRED_ROLE;
+
+		ret = fwnode_property_read_string(fwnode, "try-power-role", &cap_str);
+		if (ret == 0) {
+			ret = typec_find_power_role(cap_str);
+			if (ret < 0)
+				return ret;
+			cap->prefer_role = ret;
+		}
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(typec_get_fw_cap);
+
 /**
  * typec_port_register_altmode - Register USB Type-C Port Alternate Mode
  * @port: USB Type-C Port that supports the alternate mode
@@ -1976,6 +2026,7 @@
 		altmodes[index] = alt;
 		index++;
 	}
+	fwnode_handle_put(altmodes_node);
 }
 EXPORT_SYMBOL_GPL(typec_port_register_altmodes);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/mux.c
@@ -131,8 +131,11 @@
 	sw->dev.class = &typec_mux_class;
 	sw->dev.type = &typec_switch_dev_type;
 	sw->dev.driver_data = desc->drvdata;
-	dev_set_name(&sw->dev, "%s-switch",
-		     desc->name ? desc->name : dev_name(parent));
+	ret = dev_set_name(&sw->dev, "%s-switch", desc->name ? desc->name : dev_name(parent));
+	if (ret) {
+		put_device(&sw->dev);
+		return ERR_PTR(ret);
+	}
 
 	ret = device_add(&sw->dev);
 	if (ret) {
@@ -338,8 +341,11 @@
 	mux->dev.class = &typec_mux_class;
 	mux->dev.type = &typec_mux_dev_type;
 	mux->dev.driver_data = desc->drvdata;
-	dev_set_name(&mux->dev, "%s-mux",
-		     desc->name ? desc->name : dev_name(parent));
+	ret = dev_set_name(&mux->dev, "%s-mux", desc->name ? desc->name : dev_name(parent));
+	if (ret) {
+		put_device(&mux->dev);
+		return ERR_PTR(ret);
+	}
 
 	ret = device_add(&mux->dev);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/mux/intel_pmc_mux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/mux/intel_pmc_mux.c
@@ -352,13 +352,24 @@
 	return pmc_usb_command(port, (void *)&req, sizeof(req));
 }
 
-static int pmc_usb_mux_safe_state(struct pmc_usb_port *port)
+static int pmc_usb_mux_safe_state(struct pmc_usb_port *port,
+				  struct typec_mux_state *state)
 {
 	u8 msg;
 
 	if (IOM_PORT_ACTIVITY_IS(port->iom_status, SAFE_MODE))
 		return 0;
 
+	if ((IOM_PORT_ACTIVITY_IS(port->iom_status, DP) ||
+	     IOM_PORT_ACTIVITY_IS(port->iom_status, DP_MFD)) &&
+	     state->alt && state->alt->svid == USB_TYPEC_DP_SID)
+		return 0;
+
+	if ((IOM_PORT_ACTIVITY_IS(port->iom_status, TBT) ||
+	     IOM_PORT_ACTIVITY_IS(port->iom_status, ALT_MODE_TBT_USB)) &&
+	     state->alt && state->alt->svid == USB_TYPEC_TBT_SID)
+		return 0;
+
 	msg = PMC_USB_SAFE_MODE;
 	msg |= port->usb3_port << PMC_USB_MSG_USB3_PORT_SHIFT;
 
@@ -426,7 +437,7 @@
 		return 0;
 
 	if (state->mode == TYPEC_STATE_SAFE)
-		return pmc_usb_mux_safe_state(port);
+		return pmc_usb_mux_safe_state(port, state);
 	if (state->mode == TYPEC_STATE_USB)
 		return pmc_usb_connect(port, port->role);
 
@@ -552,13 +563,6 @@
 	return ret;
 }
 
-static int is_memory(struct acpi_resource *res, void *data)
-{
-	struct resource r;
-
-	return !acpi_dev_resource_memory(res, &r);
-}
-
 /* IOM ACPI IDs and IOM_PORT_STATUS_OFFSET */
 static const struct acpi_device_id iom_acpi_ids[] = {
 	/* TigerLake */
@@ -566,6 +570,9 @@
 
 	/* AlderLake */
 	{ "INTC1079", 0x160, },
+
+	/* Meteor Lake */
+	{ "INTC107A", 0x160, },
 	{}
 };
 
@@ -589,9 +596,11 @@
 		return -ENODEV;
 
 	INIT_LIST_HEAD(&resource_list);
-	ret = acpi_dev_get_resources(adev, &resource_list, is_memory, NULL);
-	if (ret < 0)
+	ret = acpi_dev_get_memory_resources(adev, &resource_list);
+	if (ret < 0) {
+		acpi_dev_put(adev);
 		return ret;
+	}
 
 	rentry = list_first_entry_or_null(&resource_list, struct resource_entry, node);
 	if (rentry)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/Kconfig
@@ -56,7 +56,6 @@
 	tristate "Intel WhiskeyCove PMIC USB Type-C PHY driver"
 	depends on ACPI
 	depends on MFD_INTEL_PMC_BXT
-	depends on INTEL_SOC_PMIC
 	depends on BXT_WC_PMIC_OPREGION
 	help
 	  This driver adds support for USB Type-C on Intel Broxton platforms
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/fusb302.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/fusb302.c
@@ -669,25 +669,27 @@
 		ret = fusb302_i2c_mask_write(chip, FUSB_REG_MASK,
 					     FUSB_REG_MASK_BC_LVL |
 					     FUSB_REG_MASK_COMP_CHNG,
-					     FUSB_REG_MASK_COMP_CHNG);
+					     FUSB_REG_MASK_BC_LVL);
 		if (ret < 0) {
 			fusb302_log(chip, "cannot set SRC interrupt, ret=%d",
 				    ret);
 			goto done;
 		}
 		chip->intr_comp_chng = true;
+		chip->intr_bc_lvl = false;
 		break;
 	case TYPEC_CC_RD:
 		ret = fusb302_i2c_mask_write(chip, FUSB_REG_MASK,
 					     FUSB_REG_MASK_BC_LVL |
 					     FUSB_REG_MASK_COMP_CHNG,
-					     FUSB_REG_MASK_BC_LVL);
+					     FUSB_REG_MASK_COMP_CHNG);
 		if (ret < 0) {
 			fusb302_log(chip, "cannot set SRC interrupt, ret=%d",
 				    ret);
 			goto done;
 		}
 		chip->intr_bc_lvl = true;
+		chip->intr_comp_chng = false;
 		break;
 	default:
 		break;
@@ -1706,8 +1708,8 @@
 	 */
 	if (device_property_read_string(dev, "linux,extcon-name", &name) == 0) {
 		chip->extcon = extcon_get_extcon_dev(name);
-		if (!chip->extcon)
-			return -EPROBE_DEFER;
+		if (IS_ERR(chip->extcon))
+			return PTR_ERR(chip->extcon);
 	}
 
 	chip->vbus = devm_regulator_get(chip->dev, "vbus");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/tcpci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/tcpci.c
@@ -13,11 +13,10 @@
 #include <linux/property.h>
 #include <linux/regmap.h>
 #include <linux/usb/pd.h>
+#include <linux/usb/tcpci.h>
 #include <linux/usb/tcpm.h>
 #include <linux/usb/typec.h>
 
-#include "tcpci.h"
-
 #define	PD_RETRY_COUNT_DEFAULT			3
 #define	PD_RETRY_COUNT_3_0_OR_HIGHER		2
 #define	AUTO_DISCHARGE_DEFAULT_THRESHOLD_MV	3500
@@ -27,6 +26,7 @@
 #define	VPPS_NEW_MIN_PERCENT			95
 #define	VPPS_VALID_MIN_MV			100
 #define	VSINKDISCONNECT_PD_MIN_PERCENT		90
+#define	VPPS_SHUTDOWN_MIN_PERCENT		85
 
 #define tcpc_presenting_rd(reg, cc) \
 	(!(TCPC_ROLE_CTRL_DRP & (reg)) && \
@@ -75,9 +75,25 @@
 static int tcpci_set_cc(struct tcpc_dev *tcpc, enum typec_cc_status cc)
 {
 	struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
+	bool vconn_pres;
+	enum typec_cc_polarity polarity = TYPEC_POLARITY_CC1;
 	unsigned int reg;
 	int ret;
 
+	ret = regmap_read(tcpci->regmap, TCPC_POWER_STATUS, &reg);
+	if (ret < 0)
+		return ret;
+
+	vconn_pres = !!(reg & TCPC_POWER_STATUS_VCONN_PRES);
+	if (vconn_pres) {
+		ret = regmap_read(tcpci->regmap, TCPC_TCPC_CTRL, &reg);
+		if (ret < 0)
+			return ret;
+
+		if (reg & TCPC_TCPC_CTRL_ORIENTATION)
+			polarity = TYPEC_POLARITY_CC2;
+	}
+
 	switch (cc) {
 	case TYPEC_CC_RA:
 		reg = (TCPC_ROLE_CTRL_CC_RA << TCPC_ROLE_CTRL_CC1_SHIFT) |
@@ -112,6 +128,16 @@
 		break;
 	}
 
+	if (vconn_pres) {
+		if (polarity == TYPEC_POLARITY_CC2) {
+			reg &= ~(TCPC_ROLE_CTRL_CC1_MASK << TCPC_ROLE_CTRL_CC1_SHIFT);
+			reg |= (TCPC_ROLE_CTRL_CC_OPEN << TCPC_ROLE_CTRL_CC1_SHIFT);
+		} else {
+			reg &= ~(TCPC_ROLE_CTRL_CC2_MASK << TCPC_ROLE_CTRL_CC2_SHIFT);
+			reg |= (TCPC_ROLE_CTRL_CC_OPEN << TCPC_ROLE_CTRL_CC2_SHIFT);
+		}
+	}
+
 	ret = regmap_write(tcpci->regmap, TCPC_ROLE_CTRL, reg);
 	if (ret < 0)
 		return ret;
@@ -333,7 +359,8 @@
 }
 
 static int tcpci_set_auto_vbus_discharge_threshold(struct tcpc_dev *dev, enum typec_pwr_opmode mode,
-						   bool pps_active, u32 requested_vbus_voltage_mv)
+						   bool pps_active, u32 requested_vbus_voltage_mv,
+						   u32 apdo_min_voltage_mv)
 {
 	struct tcpci *tcpci = tcpc_to_tcpci(dev);
 	unsigned int pwr_ctrl, threshold = 0;
@@ -355,9 +382,12 @@
 		threshold = AUTO_DISCHARGE_DEFAULT_THRESHOLD_MV;
 	} else if (mode == TYPEC_PWR_MODE_PD) {
 		if (pps_active)
-			threshold = ((VPPS_NEW_MIN_PERCENT * requested_vbus_voltage_mv / 100) -
-				     VSINKPD_MIN_IR_DROP_MV - VPPS_VALID_MIN_MV) *
-				     VSINKDISCONNECT_PD_MIN_PERCENT / 100;
+			/*
+			 * To prevent disconnect when the source is in Current Limit Mode.
+			 * Set the threshold to the lowest possible voltage vPpsShutdown (min)
+			 */
+			threshold = VPPS_SHUTDOWN_MIN_PERCENT * apdo_min_voltage_mv / 100 -
+				    VSINKPD_MIN_IR_DROP_MV;
 		else
 			threshold = ((VSRC_NEW_MIN_PERCENT * requested_vbus_voltage_mv / 100) -
 				     VSINKPD_MIN_IR_DROP_MV - VSRC_VALID_MIN_MV) *
@@ -590,6 +620,10 @@
 	if (time_after(jiffies, timeout))
 		return -ETIMEDOUT;
 
+	ret = tcpci_write16(tcpci, TCPC_FAULT_STATUS, TCPC_FAULT_STATUS_ALL_REG_RST_TO_DEFAULT);
+	if (ret < 0)
+		return ret;
+
 	/* Handle vendor init */
 	if (tcpci->data->init) {
 		ret = tcpci->data->init(tcpci, tcpci->data);
@@ -791,8 +825,10 @@
 		return ERR_PTR(err);
 
 	tcpci->port = tcpm_register_port(tcpci->dev, &tcpci->tcpc);
-	if (IS_ERR(tcpci->port))
+	if (IS_ERR(tcpci->port)) {
+		fwnode_handle_put(tcpci->tcpc.fwnode);
 		return ERR_CAST(tcpci->port);
+	}
 
 	return tcpci;
 }
@@ -801,6 +837,7 @@
 void tcpci_unregister_port(struct tcpci *tcpci)
 {
 	tcpm_unregister_port(tcpci->port);
+	fwnode_handle_put(tcpci->tcpc.fwnode);
 }
 EXPORT_SYMBOL_GPL(tcpci_unregister_port);
 
@@ -851,7 +888,7 @@
 	/* Disable chip interrupts before unregistering port */
 	err = tcpci_write16(chip->tcpci, TCPC_ALERT_MASK, 0);
 	if (err < 0)
-		return err;
+		dev_warn(&client->dev, "Failed to disable irqs (%pe)\n", ERR_PTR(err));
 
 	tcpci_unregister_port(chip->tcpci);
 
@@ -867,6 +904,7 @@
 #ifdef CONFIG_OF
 static const struct of_device_id tcpci_of_match[] = {
 	{ .compatible = "nxp,ptn5110", },
+	{ .compatible = "tcpci", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, tcpci_of_match);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/tcpci_maxim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/tcpci_maxim.c
@@ -11,11 +11,10 @@
 #include <linux/module.h>
 #include <linux/regmap.h>
 #include <linux/usb/pd.h>
+#include <linux/usb/tcpci.h>
 #include <linux/usb/tcpm.h>
 #include <linux/usb/typec.h>
 
-#include "tcpci.h"
-
 #define PD_ACTIVITY_TIMEOUT_MS				10000
 
 #define TCPC_VENDOR_ALERT				0x80
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/tcpci_mt6360.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/tcpci_mt6360.c
@@ -11,10 +11,12 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
+#include <linux/usb/tcpci.h>
 #include <linux/usb/tcpm.h>
 
-#include "tcpci.h"
-
+#define MT6360_REG_PHYCTRL1	0x80
+#define MT6360_REG_PHYCTRL3	0x82
+#define MT6360_REG_PHYCTRL7	0x86
 #define MT6360_REG_VCONNCTRL1	0x8C
 #define MT6360_REG_MODECTRL2	0x8F
 #define MT6360_REG_SWRESET	0xA0
@@ -22,6 +24,8 @@
 #define MT6360_REG_DRPCTRL1	0xA2
 #define MT6360_REG_DRPCTRL2	0xA3
 #define MT6360_REG_I2CTORST	0xBF
+#define MT6360_REG_PHYCTRL11	0xCA
+#define MT6360_REG_RXCTRL1	0xCE
 #define MT6360_REG_RXCTRL2	0xCF
 #define MT6360_REG_CTDCTRL2	0xEC
 
@@ -106,6 +110,27 @@
 	if (ret)
 		return ret;
 
+	/* BMC PHY */
+	ret = mt6360_tcpc_write16(regmap, MT6360_REG_PHYCTRL1, 0x3A70);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(regmap, MT6360_REG_PHYCTRL3,  0x82);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(regmap, MT6360_REG_PHYCTRL7, 0x36);
+	if (ret)
+		return ret;
+
+	ret = mt6360_tcpc_write16(regmap, MT6360_REG_PHYCTRL11, 0x3C60);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(regmap, MT6360_REG_RXCTRL1, 0xE8);
+	if (ret)
+		return ret;
+
 	/* Set shipping mode off, AUTOIDLE on */
 	return regmap_write(regmap, MT6360_REG_MODECTRL2, 0x7A);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/tcpci_rt1711h.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/tcpci_rt1711h.c
@@ -10,9 +10,9 @@
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/gpio/consumer.h>
+#include <linux/usb/tcpci.h>
 #include <linux/usb/tcpm.h>
 #include <linux/regmap.h>
-#include "tcpci.h"
 
 #define RT1711H_VID		0x29CF
 #define RT1711H_PID		0x1711
@@ -217,6 +217,11 @@
 {
 	int ret;
 	struct rt1711h_chip *chip;
+	const u16 alert_mask = TCPC_ALERT_TX_SUCCESS | TCPC_ALERT_TX_DISCARDED |
+			       TCPC_ALERT_TX_FAILED | TCPC_ALERT_RX_HARD_RST |
+			       TCPC_ALERT_RX_STATUS | TCPC_ALERT_POWER_STATUS |
+			       TCPC_ALERT_CC_STATUS | TCPC_ALERT_RX_BUF_OVF |
+			       TCPC_ALERT_FAULT;
 
 	ret = rt1711h_check_revision(client);
 	if (ret < 0) {
@@ -258,6 +263,12 @@
 					dev_name(chip->dev), chip);
 	if (ret < 0)
 		return ret;
+
+	/* Enable alert interrupts */
+	ret = rt1711h_write16(chip, TCPC_ALERT_MASK, alert_mask);
+	if (ret < 0)
+		return ret;
+
 	enable_irq_wake(client->irq);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/tcpm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/tcpm.c
@@ -324,6 +324,7 @@
 
 	bool attached;
 	bool connected;
+	bool registered;
 	bool pd_supported;
 	enum typec_port_type port_type;
 
@@ -1427,10 +1428,18 @@
 static void tcpm_queue_vdm(struct tcpm_port *port, const u32 header,
 			   const u32 *data, int cnt)
 {
+	u32 vdo_hdr = port->vdo_data[0];
+
 	WARN_ON(!mutex_is_locked(&port->lock));
 
-	/* Make sure we are not still processing a previous VDM packet */
-	WARN_ON(port->vdm_state > VDM_STATE_DONE);
+	/* If is sending discover_identity, handle received message first */
+	if (PD_VDO_SVDM(vdo_hdr) && PD_VDO_CMD(vdo_hdr) == CMD_DISCOVER_IDENT) {
+		port->send_discover = true;
+		mod_send_discover_delayed_work(port, SEND_DISCOVER_RETRY_MS);
+	} else {
+		/* Make sure we are not still processing a previous VDM packet */
+		WARN_ON(port->vdm_state > VDM_STATE_DONE);
+	}
 
 	port->vdo_count = cnt + 1;
 	port->vdo_data[0] = header;
@@ -1462,7 +1471,8 @@
 	port->partner_ident.cert_stat = p[VDO_INDEX_CSTAT];
 	port->partner_ident.product = product;
 
-	typec_partner_set_identity(port->partner);
+	if (port->partner)
+		typec_partner_set_identity(port->partner);
 
 	tcpm_log(port, "Identity: %04x:%04x.%04x",
 		 PD_IDH_VID(vdo),
@@ -1497,7 +1507,21 @@
 		pmdata->svids[pmdata->nsvids++] = svid;
 		tcpm_log(port, "SVID %d: 0x%x", pmdata->nsvids, svid);
 	}
-	return true;
+
+	/*
+	 * PD3.0 Spec 6.4.4.3.2: The SVIDs are returned 2 per VDO (see Table
+	 * 6-43), and can be returned maximum 6 VDOs per response (see Figure
+	 * 6-19). If the Respondersupports 12 or more SVID then the Discover
+	 * SVIDs Command Shall be executed multiple times until a Discover
+	 * SVIDs VDO is returned ending either with a SVID value of 0x0000 in
+	 * the last part of the last VDO or with a VDO containing two SVIDs
+	 * with values of 0x0000.
+	 *
+	 * However, some odd dockers support SVIDs less than 12 but without
+	 * 0x0000 in the last VDO, so we need to break the Discover SVIDs
+	 * request and return false here.
+	 */
+	return cnt == 7;
 abort:
 	tcpm_log(port, "SVID_DISCOVERY_MAX(%d) too low!", SVID_DISCOVERY_MAX);
 	return false;
@@ -1536,6 +1560,9 @@
 	struct typec_altmode *altmode;
 	int i;
 
+	if (!port->partner)
+		return;
+
 	for (i = 0; i < modep->altmodes; i++) {
 		altmode = typec_partner_register_altmode(port->partner,
 						&modep->altmode_desc[i]);
@@ -1585,6 +1612,9 @@
 			if (PD_VDO_VID(p[0]) != USB_SID_PD)
 				break;
 
+			if (IS_ERR_OR_NULL(port->partner))
+				break;
+
 			if (PD_VDO_SVDM_VER(p[0]) < svdm_version) {
 				typec_partner_set_svdm_version(port->partner,
 							       PD_VDO_SVDM_VER(p[0]));
@@ -1840,7 +1870,8 @@
 			}
 			break;
 		case ADEV_ATTENTION:
-			typec_altmode_attention(adev, p[1]);
+			if (typec_altmode_attention(adev, p[1]))
+				tcpm_log(port, "typec_altmode_attention no port partner altmode");
 			break;
 		}
 	}
@@ -1933,11 +1964,13 @@
 			switch (PD_VDO_CMD(vdo_hdr)) {
 			case CMD_DISCOVER_IDENT:
 				res = tcpm_ams_start(port, DISCOVER_IDENTITY);
-				if (res == 0)
+				if (res == 0) {
 					port->send_discover = false;
-				else if (res == -EAGAIN)
+				} else if (res == -EAGAIN) {
+					port->vdo_data[0] = 0;
 					mod_send_discover_delayed_work(port,
 								       SEND_DISCOVER_RETRY_MS);
+				}
 				break;
 			case CMD_DISCOVER_SVID:
 				res = tcpm_ams_start(port, DISCOVER_SVIDS);
@@ -2020,6 +2053,7 @@
 			unsigned long timeout;
 
 			port->vdm_retries = 0;
+			port->vdo_data[0] = 0;
 			port->vdm_state = VDM_STATE_BUSY;
 			timeout = vdm_ready_timeout(vdo_hdr);
 			mod_vdm_delayed_work(port, timeout);
@@ -2278,10 +2312,12 @@
 		return 0;
 
 	ret = port->tcpc->set_auto_vbus_discharge_threshold(port->tcpc, mode, pps_active,
-							    requested_vbus_voltage);
+							    requested_vbus_voltage,
+							    port->pps_data.min_volt);
 	tcpm_log_force(port,
-		       "set_auto_vbus_discharge_threshold mode:%d pps_active:%c vbus:%u ret:%d",
-		       mode, pps_active ? 'y' : 'n', requested_vbus_voltage, ret);
+		       "set_auto_vbus_discharge_threshold mode:%d pps_active:%c vbus:%u pps_apdo_min_volt:%u ret:%d",
+		       mode, pps_active ? 'y' : 'n', requested_vbus_voltage,
+		       port->pps_data.min_volt, ret);
 
 	return ret;
 }
@@ -2663,6 +2699,13 @@
 			port->sink_cap_done = true;
 			tcpm_set_state(port, ready_state(port), 0);
 			break;
+		/*
+		 * Some port partners do not support GET_STATUS, avoid soft reset the link to
+		 * prevent redundant power re-negotiation
+		 */
+		case GET_STATUS_SEND:
+			tcpm_set_state(port, ready_state(port), 0);
+			break;
 		case SRC_READY:
 		case SNK_READY:
 			if (port->vdm_state > VDM_STATE_READY) {
@@ -3540,7 +3583,10 @@
 
 static void tcpm_typec_connect(struct tcpm_port *port)
 {
+	struct typec_partner *partner;
+
 	if (!port->connected) {
+		port->connected = true;
 		/* Make sure we don't report stale identity information */
 		memset(&port->partner_ident, 0, sizeof(port->partner_ident));
 		port->partner_desc.usb_pd = port->pd_capable;
@@ -3550,9 +3596,13 @@
 			port->partner_desc.accessory = TYPEC_ACCESSORY_AUDIO;
 		else
 			port->partner_desc.accessory = TYPEC_ACCESSORY_NONE;
-		port->partner = typec_register_partner(port->typec_port,
-						       &port->partner_desc);
-		port->connected = true;
+		partner = typec_register_partner(port->typec_port, &port->partner_desc);
+		if (IS_ERR(partner)) {
+			dev_err(port->dev, "Failed to register partner (%ld)\n", PTR_ERR(partner));
+			return;
+		}
+
+		port->partner = partner;
 	}
 }
 
@@ -3621,8 +3671,10 @@
 static void tcpm_typec_disconnect(struct tcpm_port *port)
 {
 	if (port->connected) {
-		typec_unregister_partner(port->partner);
-		port->partner = NULL;
+		if (port->partner) {
+			typec_unregister_partner(port->partner);
+			port->partner = NULL;
+		}
 		port->connected = false;
 	}
 }
@@ -3829,6 +3881,32 @@
 	}
 }
 
+static void tcpm_set_initial_svdm_version(struct tcpm_port *port)
+{
+	if (!port->partner)
+		return;
+
+	switch (port->negotiated_rev) {
+	case PD_REV30:
+		break;
+	/*
+	 * 6.4.4.2.3 Structured VDM Version
+	 * 2.0 states "At this time, there is only one version (1.0) defined.
+	 * This field Shall be set to zero to indicate Version 1.0."
+	 * 3.0 states "This field Shall be set to 01b to indicate Version 2.0."
+	 * To ensure that we follow the Power Delivery revision we are currently
+	 * operating on, downgrade the SVDM version to the highest one supported
+	 * by the Power Delivery revision.
+	 */
+	case PD_REV20:
+		typec_partner_set_svdm_version(port->partner, SVDM_VER_1_0);
+		break;
+	default:
+		typec_partner_set_svdm_version(port->partner, SVDM_VER_1_0);
+		break;
+	}
+}
+
 static void run_state_machine(struct tcpm_port *port)
 {
 	int ret;
@@ -3966,7 +4044,7 @@
 			port->caps_count = 0;
 			port->pd_capable = true;
 			tcpm_set_state_cond(port, SRC_SEND_CAPABILITIES_TIMEOUT,
-					    PD_T_SEND_SOURCE_CAP);
+					    PD_T_SENDER_RESPONSE);
 		}
 		break;
 	case SRC_SEND_CAPABILITIES_TIMEOUT:
@@ -4053,10 +4131,12 @@
 		 * For now, this driver only supports SOP for DISCOVER_IDENTITY, thus using
 		 * port->explicit_contract to decide whether to send the command.
 		 */
-		if (port->explicit_contract)
+		if (port->explicit_contract) {
+			tcpm_set_initial_svdm_version(port);
 			mod_send_discover_delayed_work(port, 0);
-		else
+		} else {
 			port->send_discover = false;
+		}
 
 		/*
 		 * 6.3.5
@@ -4110,11 +4190,7 @@
 				       tcpm_try_src(port) ? SRC_TRY
 							  : SNK_ATTACHED,
 				       0);
-		else
-			/* Wait for VBUS, but not forever */
-			tcpm_set_state(port, PORT_RESET, PD_T_PS_SOURCE_ON);
 		break;
-
 	case SRC_TRY:
 		port->try_src_count++;
 		tcpm_set_cc(port, tcpm_rp_cc(port));
@@ -4343,10 +4419,12 @@
 		 * For now, this driver only supports SOP for DISCOVER_IDENTITY, thus using
 		 * port->explicit_contract.
 		 */
-		if (port->explicit_contract)
+		if (port->explicit_contract) {
+			tcpm_set_initial_svdm_version(port);
 			mod_send_discover_delayed_work(port, 0);
-		else
+		} else {
 			port->send_discover = false;
+		}
 
 		power_supply_changed(port->psy);
 		break;
@@ -4530,14 +4608,13 @@
 		tcpm_set_state(port, ready_state(port), 0);
 		break;
 	case DR_SWAP_CHANGE_DR:
-		if (port->data_role == TYPEC_HOST) {
-			tcpm_unregister_altmodes(port);
+		tcpm_unregister_altmodes(port);
+		if (port->data_role == TYPEC_HOST)
 			tcpm_set_roles(port, true, port->pwr_role,
 				       TYPEC_DEVICE);
-		} else {
+		else
 			tcpm_set_roles(port, true, port->pwr_role,
 				       TYPEC_HOST);
-		}
 		tcpm_ams_finish(port);
 		tcpm_set_state(port, ready_state(port), 0);
 		break;
@@ -5159,7 +5236,8 @@
 	case SNK_TRYWAIT_DEBOUNCE:
 		break;
 	case SNK_ATTACH_WAIT:
-		tcpm_set_state(port, SNK_UNATTACHED, 0);
+	case SNK_DEBOUNCED:
+		/* Do nothing, as TCPM is still waiting for vbus to reaach VSAFE5V to connect */
 		break;
 
 	case SNK_NEGOTIATE_CAPABILITIES:
@@ -5224,6 +5302,10 @@
 		/* Do nothing, vbus drop expected */
 		break;
 
+	case SNK_HARD_RESET_WAIT_VBUS:
+		/* Do nothing, its OK to receive vbus off events */
+		break;
+
 	default:
 		if (port->pwr_role == TYPEC_SINK && port->attached)
 			tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
@@ -5266,6 +5348,13 @@
 	case PR_SWAP_SNK_SRC_SOURCE_ON:
 		/* Do nothing, vsafe0v is expected during transition */
 		break;
+	case SNK_ATTACH_WAIT:
+	case SNK_DEBOUNCED:
+		/*Do nothing, still waiting for VSAFE5V for connect */
+		break;
+	case SNK_HARD_RESET_WAIT_VBUS:
+		/* Do nothing, its OK to receive vbus off events */
+		break;
 	default:
 		if (port->pwr_role == TYPEC_SINK && port->auto_vbus_discharge_enabled)
 			tcpm_set_state(port, SNK_UNATTACHED, 0);
@@ -5279,6 +5368,16 @@
 	if (port->bist_request == BDO_MODE_TESTDATA && port->tcpc->set_bist_data)
 		port->tcpc->set_bist_data(port->tcpc, false);
 
+	switch (port->state) {
+	case TOGGLING:
+	case ERROR_RECOVERY:
+	case PORT_RESET:
+	case PORT_RESET_WAIT_OFF:
+		return;
+	default:
+		break;
+	}
+
 	if (port->ams != NONE_AMS)
 		port->ams = NONE_AMS;
 	if (port->hard_reset_count < PD_N_HARD_RESET_COUNT)
@@ -5926,7 +6025,6 @@
 			    struct fwnode_handle *fwnode)
 {
 	const char *opmode_str;
-	const char *cap_str;
 	int ret;
 	u32 mw, frs_current;
 
@@ -5942,23 +6040,10 @@
 	 */
 	fw_devlink_purge_absent_suppliers(fwnode);
 
-	/* USB data support is optional */
-	ret = fwnode_property_read_string(fwnode, "data-role", &cap_str);
-	if (ret == 0) {
-		ret = typec_find_port_data_role(cap_str);
-		if (ret < 0)
-			return ret;
-		port->typec_caps.data = ret;
-	}
-
-	ret = fwnode_property_read_string(fwnode, "power-role", &cap_str);
+	ret = typec_get_fw_cap(&port->typec_caps, fwnode);
 	if (ret < 0)
 		return ret;
 
-	ret = typec_find_port_power_role(cap_str);
-	if (ret < 0)
-		return ret;
-	port->typec_caps.type = ret;
 	port->port_type = port->typec_caps.type;
 	port->pd_supported = !fwnode_property_read_bool(fwnode, "pd-disable");
 
@@ -5995,14 +6080,6 @@
 	if (port->port_type == TYPEC_PORT_SRC)
 		return 0;
 
-	/* Get the preferred power role for DRP */
-	ret = fwnode_property_read_string(fwnode, "try-power-role", &cap_str);
-	if (ret < 0)
-		return ret;
-
-	port->typec_caps.prefer_role = typec_find_power_role(cap_str);
-	if (port->typec_caps.prefer_role < 0)
-		return -EINVAL;
 sink:
 	port->self_powered = fwnode_property_read_bool(fwnode, "self-powered");
 
@@ -6211,6 +6288,13 @@
 	struct tcpm_port *port = power_supply_get_drvdata(psy);
 	int ret;
 
+	/*
+	 * All the properties below are related to USB PD. The check needs to be
+	 * property specific when a non-pd related property is added.
+	 */
+	if (!port->pd_supported)
+		return -EOPNOTSUPP;
+
 	switch (psp) {
 	case POWER_SUPPLY_PROP_ONLINE:
 		ret = tcpm_psy_set_online(port, val);
@@ -6295,7 +6379,8 @@
 {
 	struct tcpm_port *port = container_of(timer, struct tcpm_port, state_machine_timer);
 
-	kthread_queue_work(port->wq, &port->state_machine);
+	if (port->registered)
+		kthread_queue_work(port->wq, &port->state_machine);
 	return HRTIMER_NORESTART;
 }
 
@@ -6303,7 +6388,8 @@
 {
 	struct tcpm_port *port = container_of(timer, struct tcpm_port, vdm_state_machine_timer);
 
-	kthread_queue_work(port->wq, &port->vdm_state_machine);
+	if (port->registered)
+		kthread_queue_work(port->wq, &port->vdm_state_machine);
 	return HRTIMER_NORESTART;
 }
 
@@ -6311,7 +6397,8 @@
 {
 	struct tcpm_port *port = container_of(timer, struct tcpm_port, enable_frs_timer);
 
-	kthread_queue_work(port->wq, &port->enable_frs);
+	if (port->registered)
+		kthread_queue_work(port->wq, &port->enable_frs);
 	return HRTIMER_NORESTART;
 }
 
@@ -6319,7 +6406,8 @@
 {
 	struct tcpm_port *port = container_of(timer, struct tcpm_port, send_discover_timer);
 
-	kthread_queue_work(port->wq, &port->send_discover_work);
+	if (port->registered)
+		kthread_queue_work(port->wq, &port->send_discover_work);
 	return HRTIMER_NORESTART;
 }
 
@@ -6407,6 +6495,7 @@
 	typec_port_register_altmodes(port->typec_port,
 				     &tcpm_altmode_ops, port,
 				     port->port_altmode, ALTMODE_DISCOVERY_MAX);
+	port->registered = true;
 
 	mutex_lock(&port->lock);
 	tcpm_init(port);
@@ -6428,6 +6517,9 @@
 {
 	int i;
 
+	port->registered = false;
+	kthread_destroy_worker(port->wq);
+
 	hrtimer_cancel(&port->send_discover_timer);
 	hrtimer_cancel(&port->enable_frs_timer);
 	hrtimer_cancel(&port->vdm_state_machine_timer);
@@ -6439,7 +6531,6 @@
 	typec_unregister_port(port->typec_port);
 	usb_role_switch_put(port->role_sw);
 	tcpm_debugfs_exit(port);
-	kthread_destroy_worker(port->wq);
 }
 EXPORT_SYMBOL_GPL(tcpm_unregister_port);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tcpm/wcove.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tcpm/wcove.c
@@ -621,10 +621,6 @@
 	if (irq < 0)
 		return irq;
 
-	irq = regmap_irq_get_virq(pmic->irq_chip_data_chgr, irq);
-	if (irq < 0)
-		return irq;
-
 	ret = guid_parse(WCOVE_DSM_UUID, &wcove->guid);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tipd/core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tipd/core.c
@@ -117,7 +117,7 @@
 	u8 data[TPS_MAX_LEN + 1];
 	int ret;
 
-	if (WARN_ON(len + 1 > sizeof(data)))
+	if (len + 1 > sizeof(data))
 		return -EINVAL;
 
 	if (!tps->i2c_protocol)
@@ -246,6 +246,10 @@
 	typec_set_pwr_opmode(tps->port, mode);
 	typec_set_pwr_role(tps->port, TPS_STATUS_TO_TYPEC_PORTROLE(status));
 	typec_set_vconn_role(tps->port, TPS_STATUS_TO_TYPEC_VCONN(status));
+	if (TPS_STATUS_TO_UPSIDE_DOWN(status))
+		typec_set_orientation(tps->port, TYPEC_ORIENTATION_REVERSE);
+	else
+		typec_set_orientation(tps->port, TYPEC_ORIENTATION_NORMAL);
 	tps6598x_set_data_role(tps, TPS_STATUS_TO_TYPEC_DATAROLE(status), true);
 
 	tps->partner = typec_register_partner(tps->port, &desc);
@@ -268,6 +272,7 @@
 	typec_set_pwr_opmode(tps->port, TYPEC_PWR_MODE_USB);
 	typec_set_pwr_role(tps->port, TPS_STATUS_TO_TYPEC_PORTROLE(status));
 	typec_set_vconn_role(tps->port, TPS_STATUS_TO_TYPEC_VCONN(status));
+	typec_set_orientation(tps->port, TYPEC_ORIENTATION_NONE);
 	tps6598x_set_data_role(tps, TPS_STATUS_TO_TYPEC_DATAROLE(status), false);
 
 	power_supply_changed(tps->psy);
@@ -618,12 +623,12 @@
 
 	ret = tps6598x_read32(tps, TPS_REG_STATUS, &status);
 	if (ret < 0)
-		return ret;
+		goto err_clear_mask;
 	trace_tps6598x_status(status);
 
 	ret = tps6598x_read32(tps, TPS_REG_SYSTEM_CONF, &conf);
 	if (ret < 0)
-		return ret;
+		goto err_clear_mask;
 
 	/*
 	 * This fwnode has a "compatible" property, but is never populated as a
@@ -679,14 +684,13 @@
 
 	ret = devm_tps6598_psy_register(tps);
 	if (ret)
-		return ret;
+		goto err_role_put;
 
 	tps->port = typec_register_port(&client->dev, &typec_cap);
 	if (IS_ERR(tps->port)) {
 		ret = PTR_ERR(tps->port);
 		goto err_role_put;
 	}
-	fwnode_handle_put(fwnode);
 
 	if (status & TPS_STATUS_PLUG_PRESENT) {
 		ret = tps6598x_connect(tps, status);
@@ -705,6 +709,7 @@
 	}
 
 	i2c_set_clientdata(client, tps);
+	fwnode_handle_put(fwnode);
 
 	return 0;
 
@@ -712,7 +717,8 @@
 	usb_role_switch_put(tps->role_sw);
 err_fwnode_put:
 	fwnode_handle_put(fwnode);
-
+err_clear_mask:
+	tps6598x_write64(tps, TPS_REG_INT_MASK1, 0);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/tipd/tps6598x.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/tipd/tps6598x.h
@@ -17,6 +17,7 @@
 /* TPS_REG_STATUS bits */
 #define TPS_STATUS_PLUG_PRESENT		BIT(0)
 #define TPS_STATUS_PLUG_UPSIDE_DOWN	BIT(4)
+#define TPS_STATUS_TO_UPSIDE_DOWN(s)	(!!((s) & TPS_STATUS_PLUG_UPSIDE_DOWN))
 #define TPS_STATUS_PORTROLE		BIT(5)
 #define TPS_STATUS_TO_TYPEC_PORTROLE(s) (!!((s) & TPS_STATUS_PORTROLE))
 #define TPS_STATUS_DATAROLE		BIT(6)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/ucsi/displayport.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/ucsi/displayport.c
@@ -275,8 +275,6 @@
 	struct ucsi_dp *dp = container_of(work, struct ucsi_dp, work);
 	int ret;
 
-	mutex_lock(&dp->con->lock);
-
 	ret = typec_altmode_vdm(dp->alt, dp->header,
 				dp->vdo_data, dp->vdo_size);
 	if (ret)
@@ -285,8 +283,6 @@
 	dp->vdo_data = NULL;
 	dp->vdo_size = 0;
 	dp->header = 0;
-
-	mutex_unlock(&dp->con->lock);
 }
 
 void ucsi_displayport_remove_partner(struct typec_altmode *alt)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/ucsi/ucsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/ucsi/ucsi.c
@@ -25,7 +25,7 @@
  * difficult to estimate the time it takes for the system to process the command
  * before it is actually passed to the PPM.
  */
-#define UCSI_TIMEOUT_MS		5000
+#define UCSI_TIMEOUT_MS		10000
 
 /*
  * UCSI_SWAP_TIMEOUT_MS - Timeout for role swap requests
@@ -76,6 +76,10 @@
 	if (ret)
 		return ret;
 
+	ret = ucsi_acknowledge_command(ucsi);
+	if (ret)
+		return ret;
+
 	switch (error) {
 	case UCSI_ERROR_INCOMPATIBLE_PARTNER:
 		return -EOPNOTSUPP;
@@ -128,14 +132,20 @@
 	if (ret)
 		return ret;
 
-	if (cci & UCSI_CCI_BUSY)
+	if (cci & UCSI_CCI_BUSY) {
+		ucsi->ops->async_write(ucsi, UCSI_CANCEL, NULL, 0);
 		return -EBUSY;
+	}
 
 	if (!(cci & UCSI_CCI_COMMAND_COMPLETE))
 		return -EIO;
 
-	if (cci & UCSI_CCI_NOT_SUPPORTED)
+	if (cci & UCSI_CCI_NOT_SUPPORTED) {
+		if (ucsi_acknowledge_command(ucsi) < 0)
+			dev_err(ucsi->dev,
+				"ACK of unsupported command failed\n");
 		return -EOPNOTSUPP;
+	}
 
 	if (cci & UCSI_CCI_ERROR) {
 		if (cmd == UCSI_GET_ERROR_STATUS)
@@ -189,6 +199,64 @@
 EXPORT_SYMBOL_GPL(ucsi_resume);
 /* -------------------------------------------------------------------------- */
 
+struct ucsi_work {
+	struct delayed_work work;
+	unsigned long delay;
+	unsigned int count;
+	struct ucsi_connector *con;
+	int (*cb)(struct ucsi_connector *);
+};
+
+static void ucsi_poll_worker(struct work_struct *work)
+{
+	struct ucsi_work *uwork = container_of(work, struct ucsi_work, work.work);
+	struct ucsi_connector *con = uwork->con;
+	int ret;
+
+	mutex_lock(&con->lock);
+
+	if (!con->partner) {
+		mutex_unlock(&con->lock);
+		kfree(uwork);
+		return;
+	}
+
+	ret = uwork->cb(con);
+
+	if (uwork->count-- && (ret == -EBUSY || ret == -ETIMEDOUT))
+		queue_delayed_work(con->wq, &uwork->work, uwork->delay);
+	else
+		kfree(uwork);
+
+	mutex_unlock(&con->lock);
+}
+
+static int ucsi_partner_task(struct ucsi_connector *con,
+			     int (*cb)(struct ucsi_connector *),
+			     int retries, unsigned long delay)
+{
+	struct ucsi_work *uwork;
+
+	if (!con->partner)
+		return 0;
+
+	uwork = kzalloc(sizeof(*uwork), GFP_KERNEL);
+	if (!uwork)
+		return -ENOMEM;
+
+	INIT_DELAYED_WORK(&uwork->work, ucsi_poll_worker);
+	uwork->count = retries;
+	uwork->delay = delay;
+	uwork->con = con;
+	uwork->cb = cb;
+
+	queue_delayed_work(con->wq, &uwork->work, delay);
+
+	return 0;
+}
+
+/* -------------------------------------------------------------------------- */
+
 void ucsi_altmode_update_active(struct ucsi_connector *con)
 {
 	const struct typec_altmode *altmode = NULL;
@@ -435,6 +503,8 @@
 		command |= UCSI_GET_ALTMODE_CONNECTOR_NUMBER(con->num);
 		command |= UCSI_GET_ALTMODE_OFFSET(i);
 		len = ucsi_send_command(con->ucsi, command, alt, sizeof(alt));
+		if (len == -EBUSY)
+			continue;
 		if (len <= 0)
 			return len;
 
@@ -509,34 +579,55 @@
 	command |= UCSI_GET_PDOS_SRC_PDOS;
 	ret = ucsi_send_command(ucsi, command, pdos + offset,
 				num_pdos * sizeof(u32));
-	if (ret < 0)
+	if (ret < 0 && ret != -ETIMEDOUT)
 		dev_err(ucsi->dev, "UCSI_GET_PDOS failed (%d)\n", ret);
-	if (ret == 0 && offset == 0)
-		dev_warn(ucsi->dev, "UCSI_GET_PDOS returned 0 bytes\n");
 
 	return ret;
 }
 
-static void ucsi_get_src_pdos(struct ucsi_connector *con, int is_partner)
+static int ucsi_get_src_pdos(struct ucsi_connector *con)
 {
 	int ret;
 
 	/* UCSI max payload means only getting at most 4 PDOs at a time */
 	ret = ucsi_get_pdos(con, 1, con->src_pdos, 0, UCSI_MAX_PDOS);
 	if (ret < 0)
-		return;
+		return ret;
 
 	con->num_pdos = ret / sizeof(u32); /* number of bytes to 32-bit PDOs */
 	if (con->num_pdos < UCSI_MAX_PDOS)
-		return;
+		return 0;
 
 	/* get the remaining PDOs, if any */
 	ret = ucsi_get_pdos(con, 1, con->src_pdos, UCSI_MAX_PDOS,
 			    PDO_MAX_OBJECTS - UCSI_MAX_PDOS);
 	if (ret < 0)
-		return;
+		return ret;
 
 	con->num_pdos += ret / sizeof(u32);
+
+	ucsi_port_psy_changed(con);
+
+	return 0;
+}
+
+static int ucsi_check_altmodes(struct ucsi_connector *con)
+{
+	int ret;
+
+	ret = ucsi_register_altmodes(con, UCSI_RECIPIENT_SOP);
+	if (ret && ret != -ETIMEDOUT)
+		dev_err(con->ucsi->dev,
+			"con%d: failed to register partner alt modes (%d)\n",
+			con->num, ret);
+
+	/* Ignoring the errors in this case. */
+	if (con->partner_altmode[0]) {
+		ucsi_altmode_update_active(con);
+		return 0;
+	}
+
+	return ret;
 }
 
 static void ucsi_pwr_opmode_change(struct ucsi_connector *con)
@@ -545,7 +636,8 @@
 	case UCSI_CONSTAT_PWR_OPMODE_PD:
 		con->rdo = con->status.request_data_obj;
 		typec_set_pwr_opmode(con->port, TYPEC_PWR_MODE_PD);
-		ucsi_get_src_pdos(con, 1);
+		ucsi_partner_task(con, ucsi_get_src_pdos, 30, 0);
+		ucsi_partner_task(con, ucsi_check_altmodes, 30, 0);
 		break;
 	case UCSI_CONSTAT_PWR_OPMODE_TYPEC1_5:
 		con->rdo = 0;
@@ -614,9 +706,6 @@
 	enum usb_role u_role = USB_ROLE_NONE;
 	int ret;
 
-	if (!con->partner)
-		return;
-
 	switch (UCSI_CONSTAT_PARTNER_TYPE(con->status.flags)) {
 	case UCSI_CONSTAT_PARTNER_TYPE_UFP:
 	case UCSI_CONSTAT_PARTNER_TYPE_CABLE_AND_UFP:
@@ -633,10 +722,6 @@
 		break;
 	}
 
-	/* Complete pending data role swap */
-	if (!completion_done(&con->complete))
-		complete(&con->complete);
-
 	/* Only notify USB controller if partner supports USB data */
 	if (!(UCSI_CONSTAT_PARTNER_FLAGS(con->status.flags) & UCSI_CONSTAT_PARTNER_FLAG_USB))
 		u_role = USB_ROLE_NONE;
@@ -645,15 +730,31 @@
 	if (ret)
 		dev_err(con->ucsi->dev, "con:%d: failed to set usb role:%d\n",
 			con->num, u_role);
+}
 
-	/* Can't rely on Partner Flags field. Always checking the alt modes. */
-	ret = ucsi_register_altmodes(con, UCSI_RECIPIENT_SOP);
-	if (ret)
-		dev_err(con->ucsi->dev,
-			"con%d: failed to register partner alternate modes\n",
-			con->num);
-	else
-		ucsi_altmode_update_active(con);
+static int ucsi_check_connection(struct ucsi_connector *con)
+{
+	u64 command;
+	int ret;
+
+	command = UCSI_GET_CONNECTOR_STATUS | UCSI_CONNECTOR_NUMBER(con->num);
+	ret = ucsi_send_command(con->ucsi, command, &con->status, sizeof(con->status));
+	if (ret < 0) {
+		dev_err(con->ucsi->dev, "GET_CONNECTOR_STATUS failed (%d)\n", ret);
+		return ret;
+	}
+
+	if (con->status.flags & UCSI_CONSTAT_CONNECTED) {
+		if (UCSI_CONSTAT_PWR_OPMODE(con->status.flags) ==
+		    UCSI_CONSTAT_PWR_OPMODE_PD)
+			ucsi_partner_task(con, ucsi_check_altmodes, 30, 0);
+	} else {
+		ucsi_partner_change(con);
+		ucsi_port_psy_changed(con);
+		ucsi_unregister_partner(con);
+	}
+
+	return 0;
 }
 
 static void ucsi_handle_connector_change(struct work_struct *work)
@@ -661,122 +762,24 @@
 	struct ucsi_connector *con = container_of(work, struct ucsi_connector,
 						  work);
 	struct ucsi *ucsi = con->ucsi;
-	struct ucsi_connector_status pre_ack_status;
-	struct ucsi_connector_status post_ack_status;
 	enum typec_role role;
-	enum usb_role u_role = USB_ROLE_NONE;
-	u16 inferred_changes;
-	u16 changed_flags;
 	u64 command;
 	int ret;
 
 	mutex_lock(&con->lock);
 
-	/*
-	 * Some/many PPMs have an issue where all fields in the change bitfield
-	 * are cleared when an ACK is send. This will causes any change
-	 * between GET_CONNECTOR_STATUS and ACK to be lost.
-	 *
-	 * We work around this by re-fetching the connector status afterwards.
-	 * We then infer any changes that we see have happened but that may not
-	 * be represented in the change bitfield.
-	 *
-	 * Also, even though we don't need to know the currently supported alt
-	 * modes, we run the GET_CAM_SUPPORTED command to ensure the PPM does
-	 * not get stuck in case it assumes we do.
-	 * Always do this, rather than relying on UCSI_CONSTAT_CAM_CHANGE to be
-	 * set in the change bitfield.
-	 *
-	 * We end up with the following actions:
-	 *  1. UCSI_GET_CONNECTOR_STATUS, store result, update unprocessed_changes
-	 *  2. UCSI_GET_CAM_SUPPORTED, discard result
-	 *  3. ACK connector change
-	 *  4. UCSI_GET_CONNECTOR_STATUS, store result
-	 *  5. Infere lost changes by comparing UCSI_GET_CONNECTOR_STATUS results
-	 *  6. If PPM reported a new change, then restart in order to ACK
-	 *  7. Process everything as usual.
-	 *
-	 * We may end up seeing a change twice, but we can only miss extremely
-	 * short transitional changes.
-	 */
-
-	/* 1. First UCSI_GET_CONNECTOR_STATUS */
-	command = UCSI_GET_CONNECTOR_STATUS | UCSI_CONNECTOR_NUMBER(con->num);
-	ret = ucsi_send_command(ucsi, command, &pre_ack_status,
-				sizeof(pre_ack_status));
-	if (ret < 0) {
-		dev_err(ucsi->dev, "%s: GET_CONNECTOR_STATUS failed (%d)\n",
-			__func__, ret);
-		goto out_unlock;
-	}
-	con->unprocessed_changes |= pre_ack_status.change;
-
-	/* 2. Run UCSI_GET_CAM_SUPPORTED and discard the result. */
-	command = UCSI_GET_CAM_SUPPORTED;
-	command |= UCSI_CONNECTOR_NUMBER(con->num);
-	ucsi_send_command(con->ucsi, command, NULL, 0);
-
-	/* 3. ACK connector change */
-	ret = ucsi_acknowledge_connector_change(ucsi);
-	clear_bit(EVENT_PENDING, &ucsi->flags);
-	if (ret) {
-		dev_err(ucsi->dev, "%s: ACK failed (%d)", __func__, ret);
-		goto out_unlock;
-	}
-
-	/* 4. Second UCSI_GET_CONNECTOR_STATUS */
 	command = UCSI_GET_CONNECTOR_STATUS | UCSI_CONNECTOR_NUMBER(con->num);
-	ret = ucsi_send_command(ucsi, command, &post_ack_status,
-				sizeof(post_ack_status));
+	ret = ucsi_send_command(ucsi, command, &con->status, sizeof(con->status));
 	if (ret < 0) {
 		dev_err(ucsi->dev, "%s: GET_CONNECTOR_STATUS failed (%d)\n",
 			__func__, ret);
 		goto out_unlock;
 	}
 
-	/* 5. Inferre any missing changes */
-	changed_flags = pre_ack_status.flags ^ post_ack_status.flags;
-	inferred_changes = 0;
-	if (UCSI_CONSTAT_PWR_OPMODE(changed_flags) != 0)
-		inferred_changes |= UCSI_CONSTAT_POWER_OPMODE_CHANGE;
-
-	if (changed_flags & UCSI_CONSTAT_CONNECTED)
-		inferred_changes |= UCSI_CONSTAT_CONNECT_CHANGE;
-
-	if (changed_flags & UCSI_CONSTAT_PWR_DIR)
-		inferred_changes |= UCSI_CONSTAT_POWER_DIR_CHANGE;
-
-	if (UCSI_CONSTAT_PARTNER_FLAGS(changed_flags) != 0)
-		inferred_changes |= UCSI_CONSTAT_PARTNER_CHANGE;
-
-	if (UCSI_CONSTAT_PARTNER_TYPE(changed_flags) != 0)
-		inferred_changes |= UCSI_CONSTAT_PARTNER_CHANGE;
-
-	/* Mask out anything that was correctly notified in the later call. */
-	inferred_changes &= ~post_ack_status.change;
-	if (inferred_changes)
-		dev_dbg(ucsi->dev, "%s: Inferred changes that would have been lost: 0x%04x\n",
-			__func__, inferred_changes);
-
-	con->unprocessed_changes |= inferred_changes;
-
-	/* 6. If PPM reported a new change, then restart in order to ACK */
-	if (post_ack_status.change)
-		goto out_unlock;
-
-	/* 7. Continue as if nothing happened */
-	con->status = post_ack_status;
-	con->status.change = con->unprocessed_changes;
-	con->unprocessed_changes = 0;
+	trace_ucsi_connector_change(con->num, &con->status);
 
 	role = !!(con->status.flags & UCSI_CONSTAT_PWR_DIR);
 
-	if (con->status.change & UCSI_CONSTAT_POWER_OPMODE_CHANGE ||
-	    con->status.change & UCSI_CONSTAT_POWER_LEVEL_CHANGE) {
-		ucsi_pwr_opmode_change(con);
-		ucsi_port_psy_changed(con);
-	}
-
 	if (con->status.change & UCSI_CONSTAT_POWER_DIR_CHANGE) {
 		typec_set_pwr_role(con->port, role);
 
@@ -787,54 +790,39 @@
 
 	if (con->status.change & UCSI_CONSTAT_CONNECT_CHANGE) {
 		typec_set_pwr_role(con->port, role);
+		ucsi_port_psy_changed(con);
+		ucsi_partner_change(con);
 
-		switch (UCSI_CONSTAT_PARTNER_TYPE(con->status.flags)) {
-		case UCSI_CONSTAT_PARTNER_TYPE_UFP:
-		case UCSI_CONSTAT_PARTNER_TYPE_CABLE_AND_UFP:
-			u_role = USB_ROLE_HOST;
-			fallthrough;
-		case UCSI_CONSTAT_PARTNER_TYPE_CABLE:
-			typec_set_data_role(con->port, TYPEC_HOST);
-			break;
-		case UCSI_CONSTAT_PARTNER_TYPE_DFP:
-			u_role = USB_ROLE_DEVICE;
-			typec_set_data_role(con->port, TYPEC_DEVICE);
-			break;
-		default:
-			break;
-		}
-
-		if (con->status.flags & UCSI_CONSTAT_CONNECTED)
+		if (con->status.flags & UCSI_CONSTAT_CONNECTED) {
 			ucsi_register_partner(con);
-		else
+			ucsi_partner_task(con, ucsi_check_connection, 1, HZ);
+		} else {
 			ucsi_unregister_partner(con);
+		}
+	}
 
-		ucsi_port_psy_changed(con);
+	if (con->status.change & UCSI_CONSTAT_POWER_OPMODE_CHANGE ||
+	    con->status.change & UCSI_CONSTAT_POWER_LEVEL_CHANGE)
+		ucsi_pwr_opmode_change(con);
 
-		/* Only notify USB controller if partner supports USB data */
-		if (!(UCSI_CONSTAT_PARTNER_FLAGS(con->status.flags) &
-				UCSI_CONSTAT_PARTNER_FLAG_USB))
-			u_role = USB_ROLE_NONE;
+	if (con->partner && con->status.change & UCSI_CONSTAT_PARTNER_CHANGE) {
+		ucsi_partner_change(con);
 
-		ret = usb_role_switch_set_role(con->usb_role_sw, u_role);
-		if (ret)
-			dev_err(ucsi->dev, "con:%d: failed to set usb role:%d\n",
-				con->num, u_role);
+		/* Complete pending data role swap */
+		if (!completion_done(&con->complete))
+			complete(&con->complete);
 	}
 
-	if (con->status.change & UCSI_CONSTAT_PARTNER_CHANGE)
-		ucsi_partner_change(con);
+	if (con->status.change & UCSI_CONSTAT_CAM_CHANGE)
+		ucsi_partner_task(con, ucsi_check_altmodes, 1, 0);
 
-	trace_ucsi_connector_change(con->num, &con->status);
+	clear_bit(EVENT_PENDING, &con->ucsi->flags);
 
-out_unlock:
-	if (test_and_clear_bit(EVENT_PENDING, &ucsi->flags)) {
-		schedule_work(&con->work);
-		mutex_unlock(&con->lock);
-		return;
-	}
+	ret = ucsi_acknowledge_connector_change(ucsi);
+	if (ret)
+		dev_err(ucsi->dev, "%s: ACK failed (%d)", __func__, ret);
 
-	clear_bit(EVENT_PROCESSING, &ucsi->flags);
+out_unlock:
 	mutex_unlock(&con->lock);
 }
 
@@ -848,13 +836,11 @@
 	struct ucsi_connector *con = &ucsi->connector[num - 1];
 
 	if (!(ucsi->ntfy & UCSI_ENABLE_NTFY_CONNECTOR_CHANGE)) {
-		dev_dbg(ucsi->dev, "Bogus connector change event\n");
+		dev_dbg(ucsi->dev, "Early connector change event\n");
 		return;
 	}
 
-	set_bit(EVENT_PENDING, &ucsi->flags);
-
-	if (!test_and_set_bit(EVENT_PROCESSING, &ucsi->flags))
+	if (!test_and_set_bit(EVENT_PENDING, &ucsi->flags))
 		schedule_work(&con->work);
 }
 EXPORT_SYMBOL_GPL(ucsi_connector_change);
@@ -873,13 +859,47 @@
 
 static int ucsi_reset_ppm(struct ucsi *ucsi)
 {
-	u64 command = UCSI_PPM_RESET;
+	u64 command;
 	unsigned long tmo;
 	u32 cci;
 	int ret;
 
 	mutex_lock(&ucsi->ppm_lock);
 
+	ret = ucsi->ops->read(ucsi, UCSI_CCI, &cci, sizeof(cci));
+	if (ret < 0)
+		goto out;
+
+	/*
+	 * If UCSI_CCI_RESET_COMPLETE is already set we must clear
+	 * the flag before we start another reset. Send a
+	 * UCSI_SET_NOTIFICATION_ENABLE command to achieve this.
+	 * Ignore a timeout and try the reset anyway if this fails.
+	 */
+	if (cci & UCSI_CCI_RESET_COMPLETE) {
+		command = UCSI_SET_NOTIFICATION_ENABLE;
+		ret = ucsi->ops->async_write(ucsi, UCSI_CONTROL, &command,
+					     sizeof(command));
+		if (ret < 0)
+			goto out;
+
+		tmo = jiffies + msecs_to_jiffies(UCSI_TIMEOUT_MS);
+		do {
+			ret = ucsi->ops->read(ucsi, UCSI_CCI,
+					      &cci, sizeof(cci));
+			if (ret < 0)
+				goto out;
+			if (cci & UCSI_CCI_COMMAND_COMPLETE)
+				break;
+			if (time_is_before_jiffies(tmo))
+				break;
+			msleep(20);
+		} while (1);
+
+		WARN_ON(cci & UCSI_CCI_RESET_COMPLETE);
+	}
+
+	command = UCSI_PPM_RESET;
 	ret = ucsi->ops->async_write(ucsi, UCSI_CONTROL, &command,
 				     sizeof(command));
 	if (ret < 0)
@@ -955,6 +975,8 @@
 	     role == TYPEC_HOST))
 		goto out_unlock;
 
+	reinit_completion(&con->complete);
+
 	command = UCSI_SET_UOR | UCSI_CONNECTOR_NUMBER(con->num);
 	command |= UCSI_SET_UOR_ROLE(role);
 	command |= UCSI_SET_UOR_ACCEPT_ROLE_SWAPS;
@@ -962,14 +984,18 @@
 	if (ret < 0)
 		goto out_unlock;
 
+	mutex_unlock(&con->lock);
+
 	if (!wait_for_completion_timeout(&con->complete,
-					msecs_to_jiffies(UCSI_SWAP_TIMEOUT_MS)))
-		ret = -ETIMEDOUT;
+					 msecs_to_jiffies(UCSI_SWAP_TIMEOUT_MS)))
+		return -ETIMEDOUT;
+
+	return 0;
 
 out_unlock:
 	mutex_unlock(&con->lock);
 
-	return ret < 0 ? ret : 0;
+	return ret;
 }
 
 static int ucsi_pr_swap(struct typec_port *port, enum typec_role role)
@@ -991,6 +1017,8 @@
 	if (cur_role == role)
 		goto out_unlock;
 
+	reinit_completion(&con->complete);
+
 	command = UCSI_SET_PDR | UCSI_CONNECTOR_NUMBER(con->num);
 	command |= UCSI_SET_PDR_ROLE(role);
 	command |= UCSI_SET_PDR_ACCEPT_ROLE_SWAPS;
@@ -998,11 +1026,13 @@
 	if (ret < 0)
 		goto out_unlock;
 
+	mutex_unlock(&con->lock);
+
 	if (!wait_for_completion_timeout(&con->complete,
-				msecs_to_jiffies(UCSI_SWAP_TIMEOUT_MS))) {
-		ret = -ETIMEDOUT;
-		goto out_unlock;
-	}
+					 msecs_to_jiffies(UCSI_SWAP_TIMEOUT_MS)))
+		return -ETIMEDOUT;
+
+	mutex_lock(&con->lock);
 
 	/* Something has gone wrong while swapping the role */
 	if (UCSI_CONSTAT_PWR_OPMODE(con->status.flags) !=
@@ -1041,8 +1071,18 @@
 	enum typec_accessory *accessory = cap->accessory;
 	enum usb_role u_role = USB_ROLE_NONE;
 	u64 command;
+	char *name;
 	int ret;
 
+	name = kasprintf(GFP_KERNEL, "%s-con%d", dev_name(ucsi->dev), con->num);
+	if (!name)
+		return -ENOMEM;
+
+	con->wq = create_singlethread_workqueue(name);
+	kfree(name);
+	if (!con->wq)
+		return -ENOMEM;
+
 	INIT_WORK(&con->work, ucsi_handle_connector_change);
 	init_completion(&con->complete);
 	mutex_init(&con->lock);
@@ -1160,16 +1200,9 @@
 		ret = 0;
 	}
 
-	if (con->partner) {
-		ret = ucsi_register_altmodes(con, UCSI_RECIPIENT_SOP);
-		if (ret) {
-			dev_err(ucsi->dev,
-				"con%d: failed to register alternate modes\n",
-				con->num);
-			ret = 0;
-		} else {
-			ucsi_altmode_update_active(con);
-		}
+	if (UCSI_CONSTAT_PWR_OPMODE(con->status.flags) == UCSI_CONSTAT_PWR_OPMODE_PD) {
+		ucsi_get_src_pdos(con);
+		ucsi_check_altmodes(con);
 	}
 
 	trace_ucsi_register_port(con->num, &con->status);
@@ -1178,6 +1211,12 @@
 	fwnode_handle_put(cap->fwnode);
 out_unlock:
 	mutex_unlock(&con->lock);
+
+	if (ret && con->wq) {
+		destroy_workqueue(con->wq);
+		con->wq = NULL;
+	}
+
 	return ret;
 }
 
@@ -1190,7 +1229,8 @@
 static int ucsi_init(struct ucsi *ucsi)
 {
 	struct ucsi_connector *con;
-	u64 command;
+	u64 command, ntfy;
+	u32 cci;
 	int ret;
 	int i;
 
@@ -1202,8 +1242,8 @@
 	}
 
 	/* Enable basic notifications */
-	ucsi->ntfy = UCSI_ENABLE_NTFY_CMD_COMPLETE | UCSI_ENABLE_NTFY_ERROR;
-	command = UCSI_SET_NOTIFICATION_ENABLE | ucsi->ntfy;
+	ntfy = UCSI_ENABLE_NTFY_CMD_COMPLETE | UCSI_ENABLE_NTFY_ERROR;
+	command = UCSI_SET_NOTIFICATION_ENABLE | ntfy;
 	ret = ucsi_send_command(ucsi, command, NULL, 0);
 	if (ret < 0)
 		goto err_reset;
@@ -1235,12 +1275,22 @@
 	}
 
 	/* Enable all notifications */
-	ucsi->ntfy = UCSI_ENABLE_NTFY_ALL;
-	command = UCSI_SET_NOTIFICATION_ENABLE | ucsi->ntfy;
+	ntfy = UCSI_ENABLE_NTFY_ALL;
+	command = UCSI_SET_NOTIFICATION_ENABLE | ntfy;
 	ret = ucsi_send_command(ucsi, command, NULL, 0);
 	if (ret < 0)
 		goto err_unregister;
 
+	ucsi->ntfy = ntfy;
+
+	mutex_lock(&ucsi->ppm_lock);
+	ret = ucsi->ops->read(ucsi, UCSI_CCI, &cci, sizeof(cci));
+	mutex_unlock(&ucsi->ppm_lock);
+	if (ret)
+		return ret;
+	if (UCSI_CCI_CONNECTOR(cci))
+		ucsi_connector_change(ucsi, UCSI_CCI_CONNECTOR(cci));
+
 	return 0;
 
 err_unregister:
@@ -1248,6 +1298,8 @@
 		ucsi_unregister_partner(con);
 		ucsi_unregister_altmodes(con, UCSI_RECIPIENT_CON);
 		ucsi_unregister_port_psy(con);
+		if (con->wq)
+			destroy_workqueue(con->wq);
 		typec_unregister_port(con->port);
 		con->port = NULL;
 	}
@@ -1370,6 +1422,8 @@
 		ucsi_unregister_altmodes(&ucsi->connector[i],
 					 UCSI_RECIPIENT_CON);
 		ucsi_unregister_port_psy(&ucsi->connector[i]);
+		if (ucsi->connector[i].wq)
+			destroy_workqueue(ucsi->connector[i].wq);
 		typec_unregister_port(ucsi->connector[i].port);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/ucsi/ucsi.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/ucsi/ucsi.h
@@ -220,12 +220,12 @@
 #define UCSI_CABLE_PROP_FLAG_VBUS_IN_CABLE	BIT(0)
 #define UCSI_CABLE_PROP_FLAG_ACTIVE_CABLE	BIT(1)
 #define UCSI_CABLE_PROP_FLAG_DIRECTIONALITY	BIT(2)
-#define UCSI_CABLE_PROP_FLAG_PLUG_TYPE(_f_)	((_f_) & GENMASK(3, 0))
+#define UCSI_CABLE_PROP_FLAG_PLUG_TYPE(_f_)	(((_f_) & GENMASK(4, 3)) >> 3)
 #define   UCSI_CABLE_PROPERTY_PLUG_TYPE_A	0
 #define   UCSI_CABLE_PROPERTY_PLUG_TYPE_B	1
 #define   UCSI_CABLE_PROPERTY_PLUG_TYPE_C	2
 #define   UCSI_CABLE_PROPERTY_PLUG_OTHER	3
-#define UCSI_CABLE_PROP_MODE_SUPPORT		BIT(5)
+#define UCSI_CABLE_PROP_FLAG_MODE_SUPPORT	BIT(5)
 	u8 latency;
 } __packed;
 
@@ -300,7 +300,6 @@
 #define EVENT_PENDING	0
 #define COMMAND_PENDING	1
 #define ACK_PENDING	2
-#define EVENT_PROCESSING	3
 };
 
 #define UCSI_MAX_SVID		5
@@ -317,6 +316,7 @@
 	struct mutex lock; /* port lock */
 	struct work_struct work;
 	struct completion complete;
+	struct workqueue_struct *wq;
 
 	struct typec_port *port;
 	struct typec_partner *partner;
@@ -326,7 +326,6 @@
 
 	struct typec_capability typec_cap;
 
-	u16 unprocessed_changes;
 	struct ucsi_connector_status status;
 	struct ucsi_connector_capability cap;
 	struct power_supply *psy;
@@ -368,7 +367,7 @@
 			  bool override, int offset,
 			  struct typec_altmode_desc *desc)
 {
-	return NULL;
+	return typec_port_register_altmode(con->port, desc);
 }
 
 static inline void
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/ucsi/ucsi_acpi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/ucsi/ucsi_acpi.c
@@ -70,19 +70,26 @@
 				const void *val, size_t val_len)
 {
 	struct ucsi_acpi *ua = ucsi_get_drvdata(ucsi);
+	bool ack = UCSI_COMMAND(*(u64 *)val) == UCSI_ACK_CC_CI;
 	int ret;
 
-	set_bit(COMMAND_PENDING, &ua->flags);
+	if (ack)
+		set_bit(ACK_PENDING, &ua->flags);
+	else
+		set_bit(COMMAND_PENDING, &ua->flags);
 
 	ret = ucsi_acpi_async_write(ucsi, offset, val, val_len);
 	if (ret)
 		goto out_clear_bit;
 
-	if (!wait_for_completion_timeout(&ua->complete, 60 * HZ))
+	if (!wait_for_completion_timeout(&ua->complete, HZ))
 		ret = -ETIMEDOUT;
 
 out_clear_bit:
-	clear_bit(COMMAND_PENDING, &ua->flags);
+	if (ack)
+		clear_bit(ACK_PENDING, &ua->flags);
+	else
+		clear_bit(COMMAND_PENDING, &ua->flags);
 
 	return ret;
 }
@@ -106,8 +113,10 @@
 	if (UCSI_CCI_CONNECTOR(cci))
 		ucsi_connector_change(ua->ucsi, UCSI_CCI_CONNECTOR(cci));
 
-	if (test_bit(COMMAND_PENDING, &ua->flags) &&
-	    cci & (UCSI_CCI_ACK_COMPLETE | UCSI_CCI_COMMAND_COMPLETE))
+	if (cci & UCSI_CCI_ACK_COMPLETE && test_bit(ACK_PENDING, &ua->flags))
+		complete(&ua->complete);
+	if (cci & UCSI_CCI_COMMAND_COMPLETE &&
+	    test_bit(COMMAND_PENDING, &ua->flags))
 		complete(&ua->complete);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/typec/ucsi/ucsi_ccg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/typec/ucsi/ucsi_ccg.c
@@ -325,7 +325,7 @@
 		if (status < 0)
 			return status;
 
-		if (!data)
+		if (!(data & DEV_INT))
 			return 0;
 
 		status = ccg_write(uc, CCGX_RAB_INTR_REG, &data, sizeof(data));
@@ -436,6 +436,8 @@
 
 	port = uc->orig;
 	new_cam = UCSI_SET_NEW_CAM_GET_AM(*cmd);
+	if (new_cam >= ARRAY_SIZE(uc->updated))
+		return;
 	new_port = &uc->updated[new_cam];
 	cam = new_port->linked_idx;
 	enter_new_mode = UCSI_SET_NEW_CAM_ENTER(*cmd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/usbip/stub_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/usbip/stub_dev.c
@@ -393,7 +393,6 @@
 
 err_port:
 	dev_set_drvdata(&udev->dev, NULL);
-	usb_put_dev(udev);
 
 	/* we already have busid_priv, just lock busid_lock */
 	spin_lock(&busid_priv->busid_lock);
@@ -408,6 +407,7 @@
 	put_busid_priv(busid_priv);
 
 sdev_free:
+	usb_put_dev(udev);
 	stub_device_free(sdev);
 
 	return rc;
@@ -462,8 +462,13 @@
 	/* release port */
 	rc = usb_hub_release_port(udev->parent, udev->portnum,
 				  (struct usb_dev_state *) udev);
-	if (rc) {
-		dev_dbg(&udev->dev, "unable to release port\n");
+	/*
+	 * NOTE: If a HUB disconnect triggered disconnect of the down stream
+	 * device usb_hub_release_port will return -ENODEV so we can safely ignore
+	 * that error here.
+	 */
+	if (rc && (rc != -ENODEV)) {
+		dev_dbg(&udev->dev, "unable to release port (%i)\n", rc);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/usbip/stub_rx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/usbip/stub_rx.c
@@ -138,57 +138,68 @@
 	req = (struct usb_ctrlrequest *) urb->setup_packet;
 	config = le16_to_cpu(req->wValue);
 
+	usb_lock_device(sdev->udev);
 	err = usb_set_configuration(sdev->udev, config);
+	usb_unlock_device(sdev->udev);
 	if (err && err != -ENODEV)
 		dev_err(&sdev->udev->dev, "can't set config #%d, error %d\n",
 			config, err);
-	return 0;
+	return err;
 }
 
 static int tweak_reset_device_cmd(struct urb *urb)
 {
 	struct stub_priv *priv = (struct stub_priv *) urb->context;
 	struct stub_device *sdev = priv->sdev;
+	int err;
 
 	dev_info(&urb->dev->dev, "usb_queue_reset_device\n");
 
-	if (usb_lock_device_for_reset(sdev->udev, NULL) < 0) {
+	err = usb_lock_device_for_reset(sdev->udev, NULL);
+	if (err < 0) {
 		dev_err(&urb->dev->dev, "could not obtain lock to reset device\n");
-		return 0;
+		return err;
 	}
-	usb_reset_device(sdev->udev);
+	err = usb_reset_device(sdev->udev);
 	usb_unlock_device(sdev->udev);
 
-	return 0;
+	return err;
 }
 
 /*
  * clear_halt, set_interface, and set_configuration require special tricks.
+ * Returns 1 if request was tweaked, 0 otherwise.
  */
-static void tweak_special_requests(struct urb *urb)
+static int tweak_special_requests(struct urb *urb)
 {
+	int err;
+
 	if (!urb || !urb->setup_packet)
-		return;
+		return 0;
 
 	if (usb_pipetype(urb->pipe) != PIPE_CONTROL)
-		return;
+		return 0;
 
 	if (is_clear_halt_cmd(urb))
 		/* tweak clear_halt */
-		 tweak_clear_halt_cmd(urb);
+		err = tweak_clear_halt_cmd(urb);
 
 	else if (is_set_interface_cmd(urb))
 		/* tweak set_interface */
-		tweak_set_interface_cmd(urb);
+		err = tweak_set_interface_cmd(urb);
 
 	else if (is_set_configuration_cmd(urb))
 		/* tweak set_configuration */
-		tweak_set_configuration_cmd(urb);
+		err = tweak_set_configuration_cmd(urb);
 
 	else if (is_reset_device_cmd(urb))
-		tweak_reset_device_cmd(urb);
-	else
+		err = tweak_reset_device_cmd(urb);
+	else {
 		usbip_dbg_stub_rx("no need to tweak\n");
+		return 0;
+	}
+
+	return !err;
 }
 
 /*
@@ -466,6 +477,7 @@
 	int support_sg = 1;
 	int np = 0;
 	int ret, i;
+	int is_tweaked;
 
 	if (pipe == -1)
 		return;
@@ -578,8 +590,11 @@
 		priv->urbs[i]->pipe = pipe;
 		priv->urbs[i]->complete = stub_complete;
 
-		/* no need to submit an intercepted request, but harmless? */
-		tweak_special_requests(priv->urbs[i]);
+		/*
+		 * all URBs belong to a single PDU, so a global is_tweaked flag is
+		 * enough
+		 */
+		is_tweaked = tweak_special_requests(priv->urbs[i]);
 
 		masking_bogus_flags(priv->urbs[i]);
 	}
@@ -592,22 +607,32 @@
 
 	/* urb is now ready to submit */
 	for (i = 0; i < priv->num_urbs; i++) {
-		ret = usb_submit_urb(priv->urbs[i], GFP_KERNEL);
+		if (!is_tweaked) {
+			ret = usb_submit_urb(priv->urbs[i], GFP_KERNEL);
 
-		if (ret == 0)
-			usbip_dbg_stub_rx("submit urb ok, seqnum %u\n",
-					pdu->base.seqnum);
-		else {
-			dev_err(&udev->dev, "submit_urb error, %d\n", ret);
-			usbip_dump_header(pdu);
-			usbip_dump_urb(priv->urbs[i]);
+			if (ret == 0)
+				usbip_dbg_stub_rx("submit urb ok, seqnum %u\n",
+						pdu->base.seqnum);
+			else {
+				dev_err(&udev->dev, "submit_urb error, %d\n", ret);
+				usbip_dump_header(pdu);
+				usbip_dump_urb(priv->urbs[i]);
 
+				/*
+				 * Pessimistic.
+				 * This connection will be discarded.
+				 */
+				usbip_event_add(ud, SDEV_EVENT_ERROR_SUBMIT);
+				break;
+			}
+		} else {
 			/*
-			 * Pessimistic.
-			 * This connection will be discarded.
+			 * An identical URB was already submitted in
+			 * tweak_special_requests(). Skip submitting this URB to not
+			 * duplicate the request.
 			 */
-			usbip_event_add(ud, SDEV_EVENT_ERROR_SUBMIT);
-			break;
+			priv->urbs[i]->status = 0;
+			stub_complete(priv->urbs[i]);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/usb/usbip/vhci_hcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/usb/usbip/vhci_hcd.c
@@ -745,6 +745,7 @@
 	 *
 	 */
 	if (usb_pipedevice(urb->pipe) == 0) {
+		struct usb_device *old;
 		__u8 type = usb_pipetype(urb->pipe);
 		struct usb_ctrlrequest *ctrlreq =
 			(struct usb_ctrlrequest *) urb->setup_packet;
@@ -755,14 +756,15 @@
 			goto no_need_xmit;
 		}
 
+		old = vdev->udev;
 		switch (ctrlreq->bRequest) {
 		case USB_REQ_SET_ADDRESS:
 			/* set_address may come when a device is reset */
 			dev_info(dev, "SetAddress Request (%d) to port %d\n",
 				 ctrlreq->wValue, vdev->rhport);
 
-			usb_put_dev(vdev->udev);
 			vdev->udev = usb_get_dev(urb->dev);
+			usb_put_dev(old);
 
 			spin_lock(&vdev->ud.lock);
 			vdev->ud.status = VDEV_ST_USED;
@@ -781,8 +783,8 @@
 				usbip_dbg_vhci_hc(
 					"Not yet?:Get_Descriptor to device 0 (get max pipe size)\n");
 
-			usb_put_dev(vdev->udev);
 			vdev->udev = usb_get_dev(urb->dev);
+			usb_put_dev(old);
 			goto out;
 
 		default:
@@ -1067,6 +1069,7 @@
 static void vhci_device_reset(struct usbip_device *ud)
 {
 	struct vhci_device *vdev = container_of(ud, struct vhci_device, ud);
+	struct usb_device *old = vdev->udev;
 	unsigned long flags;
 
 	spin_lock_irqsave(&ud->lock, flags);
@@ -1074,8 +1077,8 @@
 	vdev->speed  = 0;
 	vdev->devid  = 0;
 
-	usb_put_dev(vdev->udev);
 	vdev->udev = NULL;
+	usb_put_dev(old);
 
 	if (ud->tcp_socket) {
 		sockfd_put(ud->tcp_socket);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/ifcvf/ifcvf_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/ifcvf/ifcvf_base.c
@@ -105,7 +105,7 @@
 	u32 i;
 
 	ret = pci_read_config_byte(pdev, PCI_CAPABILITY_LIST, &pos);
-	if (ret < 0) {
+	if (ret) {
 		IFCVF_ERR(pdev, "Failed to read PCI capability list\n");
 		return -EIO;
 	}
@@ -143,8 +143,8 @@
 			IFCVF_DBG(pdev, "hw->isr = %p\n", hw->isr);
 			break;
 		case VIRTIO_PCI_CAP_DEVICE_CFG:
-			hw->net_cfg = get_cap_addr(hw, &cap);
-			IFCVF_DBG(pdev, "hw->net_cfg = %p\n", hw->net_cfg);
+			hw->dev_cfg = get_cap_addr(hw, &cap);
+			IFCVF_DBG(pdev, "hw->dev_cfg = %p\n", hw->dev_cfg);
 			break;
 		}
 
@@ -153,7 +153,7 @@
 	}
 
 	if (hw->common_cfg == NULL || hw->notify_base == NULL ||
-	    hw->isr == NULL || hw->net_cfg == NULL) {
+	    hw->isr == NULL || hw->dev_cfg == NULL) {
 		IFCVF_ERR(pdev, "Incomplete PCI capabilities\n");
 		return -EIO;
 	}
@@ -174,7 +174,7 @@
 	IFCVF_DBG(pdev,
 		  "PCI capability mapping: common cfg: %p, notify base: %p\n, isr cfg: %p, device cfg: %p, multiplier: %u\n",
 		  hw->common_cfg, hw->notify_base, hw->isr,
-		  hw->net_cfg, hw->notify_off_multiplier);
+		  hw->dev_cfg, hw->notify_off_multiplier);
 
 	return 0;
 }
@@ -242,33 +242,54 @@
 	return 0;
 }
 
-void ifcvf_read_net_config(struct ifcvf_hw *hw, u64 offset,
+u32 ifcvf_get_config_size(struct ifcvf_hw *hw)
+{
+	struct ifcvf_adapter *adapter;
+	u32 config_size;
+
+	adapter = vf_to_adapter(hw);
+	switch (hw->dev_type) {
+	case VIRTIO_ID_NET:
+		config_size = sizeof(struct virtio_net_config);
+		break;
+	case VIRTIO_ID_BLOCK:
+		config_size = sizeof(struct virtio_blk_config);
+		break;
+	default:
+		config_size = 0;
+		IFCVF_ERR(adapter->pdev, "VIRTIO ID %u not supported\n", hw->dev_type);
+	}
+
+	return config_size;
+}
+
+void ifcvf_read_dev_config(struct ifcvf_hw *hw, u64 offset,
 			   void *dst, int length)
 {
 	u8 old_gen, new_gen, *p;
 	int i;
 
-	WARN_ON(offset + length > sizeof(struct virtio_net_config));
+	WARN_ON(offset + length > hw->config_size);
 	do {
 		old_gen = ifc_ioread8(&hw->common_cfg->config_generation);
 		p = dst;
 		for (i = 0; i < length; i++)
-			*p++ = ifc_ioread8(hw->net_cfg + offset + i);
+			*p++ = ifc_ioread8(hw->dev_cfg + offset + i);
 
 		new_gen = ifc_ioread8(&hw->common_cfg->config_generation);
 	} while (old_gen != new_gen);
 }
 
-void ifcvf_write_net_config(struct ifcvf_hw *hw, u64 offset,
+void ifcvf_write_dev_config(struct ifcvf_hw *hw, u64 offset,
 			    const void *src, int length)
 {
 	const u8 *p;
 	int i;
 
 	p = src;
-	WARN_ON(offset + length > sizeof(struct virtio_net_config));
+	WARN_ON(offset + length > hw->config_size);
 	for (i = 0; i < length; i++)
-		ifc_iowrite8(*p++, hw->net_cfg + offset + i);
+		ifc_iowrite8(*p++, hw->dev_cfg + offset + i);
 }
 
 static void ifcvf_set_features(struct ifcvf_hw *hw, u64 features)
@@ -306,7 +327,7 @@
 	u32 q_pair_id;
 
 	ifcvf_lm = (struct ifcvf_lm_cfg __iomem *)hw->lm_cfg;
-	q_pair_id = qid / hw->nr_vring;
+	q_pair_id = qid / 2;
 	avail_idx_addr = &ifcvf_lm->vring_lm_cfg[q_pair_id].idx_addr[qid % 2];
 	last_avail_idx = ifc_ioread16(avail_idx_addr);
 
@@ -320,7 +341,7 @@
 	u32 q_pair_id;
 
 	ifcvf_lm = (struct ifcvf_lm_cfg __iomem *)hw->lm_cfg;
-	q_pair_id = qid / hw->nr_vring;
+	q_pair_id = qid / 2;
 	avail_idx_addr = &ifcvf_lm->vring_lm_cfg[q_pair_id].idx_addr[qid % 2];
 	hw->vring[qid].last_avail_idx = num;
 	ifc_iowrite16(num, avail_idx_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/ifcvf/ifcvf_base.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/ifcvf/ifcvf_base.h
@@ -71,12 +71,14 @@
 	u64 hw_features;
 	u32 dev_type;
 	struct virtio_pci_common_cfg __iomem *common_cfg;
-	void __iomem *net_cfg;
+	void __iomem *dev_cfg;
 	struct vring_info vring[IFCVF_MAX_QUEUES];
 	void __iomem * const *base;
 	char config_msix_name[256];
 	struct vdpa_callback config_cb;
 	unsigned int config_irq;
+	/* virtio-net or virtio-blk device config size */
+	u32 config_size;
 };
 
 struct ifcvf_adapter {
@@ -105,9 +107,9 @@
 int ifcvf_start_hw(struct ifcvf_hw *hw);
 void ifcvf_stop_hw(struct ifcvf_hw *hw);
 void ifcvf_notify_queue(struct ifcvf_hw *hw, u16 qid);
-void ifcvf_read_net_config(struct ifcvf_hw *hw, u64 offset,
+void ifcvf_read_dev_config(struct ifcvf_hw *hw, u64 offset,
 			   void *dst, int length);
-void ifcvf_write_net_config(struct ifcvf_hw *hw, u64 offset,
+void ifcvf_write_dev_config(struct ifcvf_hw *hw, u64 offset,
 			    const void *src, int length);
 u8 ifcvf_get_status(struct ifcvf_hw *hw);
 void ifcvf_set_status(struct ifcvf_hw *hw, u8 status);
@@ -120,4 +122,5 @@
 int ifcvf_set_vq_state(struct ifcvf_hw *hw, u16 qid, u16 num);
 struct ifcvf_adapter *vf_to_adapter(struct ifcvf_hw *hw);
 int ifcvf_probed_virtio_net(struct ifcvf_hw *hw);
+u32 ifcvf_get_config_size(struct ifcvf_hw *hw);
 #endif /* _IFCVF_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/ifcvf/ifcvf_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/ifcvf/ifcvf_main.c
@@ -366,24 +366,9 @@
 
 static size_t ifcvf_vdpa_get_config_size(struct vdpa_device *vdpa_dev)
 {
-	struct ifcvf_adapter *adapter = vdpa_to_adapter(vdpa_dev);
 	struct ifcvf_hw *vf = vdpa_to_vf(vdpa_dev);
-	struct pci_dev *pdev = adapter->pdev;
-	size_t size;
 
-	switch (vf->dev_type) {
-	case VIRTIO_ID_NET:
-		size = sizeof(struct virtio_net_config);
-		break;
-	case VIRTIO_ID_BLOCK:
-		size = sizeof(struct virtio_blk_config);
-		break;
-	default:
-		size = 0;
-		IFCVF_ERR(pdev, "VIRTIO ID %u not supported\n", vf->dev_type);
-	}
-
-	return size;
+	return  vf->config_size;
 }
 
 static void ifcvf_vdpa_get_config(struct vdpa_device *vdpa_dev,
@@ -392,8 +377,7 @@
 {
 	struct ifcvf_hw *vf = vdpa_to_vf(vdpa_dev);
 
-	WARN_ON(offset + len > sizeof(struct virtio_net_config));
-	ifcvf_read_net_config(vf, offset, buf, len);
+	ifcvf_read_dev_config(vf, offset, buf, len);
 }
 
 static void ifcvf_vdpa_set_config(struct vdpa_device *vdpa_dev,
@@ -402,8 +386,7 @@
 {
 	struct ifcvf_hw *vf = vdpa_to_vf(vdpa_dev);
 
-	WARN_ON(offset + len > sizeof(struct virtio_net_config));
-	ifcvf_write_net_config(vf, offset, buf, len);
+	ifcvf_write_dev_config(vf, offset, buf, len);
 }
 
 static void ifcvf_vdpa_set_config_cb(struct vdpa_device *vdpa_dev,
@@ -522,7 +505,6 @@
 	}
 
 	ifcvf_mgmt_dev->adapter = adapter;
-	pci_set_drvdata(pdev, ifcvf_mgmt_dev);
 
 	vf = &adapter->vf;
 	vf->dev_type = get_dev_type(pdev);
@@ -541,6 +523,7 @@
 		vf->vring[i].irq = -EINVAL;
 
 	vf->hw_features = ifcvf_get_hw_features(vf);
+	vf->config_size = ifcvf_get_config_size(vf);
 
 	adapter->vdpa.mdev = &ifcvf_mgmt_dev->mdev;
 	ret = _vdpa_register_device(&adapter->vdpa, vf->nr_vring);
@@ -636,6 +619,8 @@
 		goto err;
 	}
 
+	pci_set_drvdata(pdev, ifcvf_mgmt_dev);
+
 	return 0;
 
 err:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/mlx5/core/mlx5_vdpa.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/mlx5/core/mlx5_vdpa.h
@@ -63,7 +63,7 @@
 	unsigned short head;
 };
 
-struct mlx5_ctrl_wq_ent {
+struct mlx5_vdpa_wq_ent {
 	struct work_struct work;
 	struct mlx5_vdpa_dev *mvdev;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/mlx5/core/mr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/mlx5/core/mr.c
@@ -227,21 +227,19 @@
 	unsigned long lgcd = 0;
 	int log_entity_size;
 	unsigned long size;
-	u64 start = 0;
 	int err;
 	struct page *pg;
 	unsigned int nsg;
 	int sglen;
-	u64 pa;
+	u64 pa, offset;
 	u64 paend;
 	struct scatterlist *sg;
 	struct device *dma = mvdev->vdev.dma_dev;
 
 	for (map = vhost_iotlb_itree_first(iotlb, mr->start, mr->end - 1);
-	     map; map = vhost_iotlb_itree_next(map, start, mr->end - 1)) {
+	     map; map = vhost_iotlb_itree_next(map, mr->start, mr->end - 1)) {
 		size = maplen(map, mr);
 		lgcd = gcd(lgcd, size);
-		start += size;
 	}
 	log_entity_size = ilog2(lgcd);
 
@@ -255,8 +253,10 @@
 	sg = mr->sg_head.sgl;
 	for (map = vhost_iotlb_itree_first(iotlb, mr->start, mr->end - 1);
 	     map; map = vhost_iotlb_itree_next(map, mr->start, mr->end - 1)) {
-		paend = map->addr + maplen(map, mr);
-		for (pa = map->addr; pa < paend; pa += sglen) {
+		offset = mr->start > map->start ? mr->start - map->start : 0;
+		pa = map->addr + offset;
+		paend = map->addr + offset + maplen(map, mr);
+		for (; pa < paend; pa += sglen) {
 			pg = pfn_to_page(__phys_to_pfn(pa));
 			if (!sg) {
 				mlx5_vdpa_warn(mvdev, "sg null. start 0x%llx, end 0x%llx\n",
@@ -505,7 +505,6 @@
 	else
 		destroy_dma_mr(mvdev, mr);
 
-	memset(mr, 0, sizeof(*mr));
 	mr->initialized = false;
 out:
 	mutex_unlock(&mr->mkey_mtx);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/mlx5/core/resources.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/mlx5/core/resources.c
@@ -215,7 +215,6 @@
 
 	mkc = MLX5_ADDR_OF(create_mkey_in, in, memory_key_mkey_entry);
 	mkey_index = MLX5_GET(create_mkey_out, lout, mkey_index);
-	mkey->iova = MLX5_GET64(mkc, mkc, start_addr);
 	mkey->size = MLX5_GET64(mkc, mkc, len);
 	mkey->key |= mlx5_idx_to_mkey(mkey_index);
 	mkey->pd = MLX5_GET(mkc, mkc, pd);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/mlx5/net/mlx5_vnet.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/mlx5/net/mlx5_vnet.c
@@ -161,6 +161,9 @@
 	bool setup;
 	u16 mtu;
 	u32 cur_num_vqs;
+	struct notifier_block nb;
+	struct vdpa_callback config_cb;
+	struct mlx5_vdpa_wq_ent cvq_ent;
 };
 
 static void free_resources(struct mlx5_vdpa_net *ndev);
@@ -170,8 +173,6 @@
 
 static bool mlx5_vdpa_debug;
 
-#define MLX5_CVQ_MAX_ENT 16
-
 #define MLX5_LOG_VIO_FLAG(_feature)                                                                \
 	do {                                                                                       \
 		if (features & BIT_ULL(_feature))                                                  \
@@ -873,8 +874,6 @@
 	MLX5_SET(virtio_q, vq_ctx, umem_3_id, mvq->umem3.id);
 	MLX5_SET(virtio_q, vq_ctx, umem_3_size, mvq->umem3.size);
 	MLX5_SET(virtio_q, vq_ctx, pd, ndev->mvdev.res.pdn);
-	if (MLX5_CAP_DEV_VDPA_EMULATION(ndev->mvdev.mdev, eth_frame_offload_type))
-		MLX5_SET(virtio_q, vq_ctx, virtio_version_1_0, 1);
 
 	err = mlx5_cmd_exec(ndev->mvdev.mdev, in, inlen, out, sizeof(out));
 	if (err)
@@ -1512,9 +1511,11 @@
 	return 0;
 
 clean_added:
-	for (--i; i >= cur_qps; --i)
+	for (--i; i >= 2 * cur_qps; --i)
 		teardown_vq(ndev, &ndev->vqs[i]);
 
+	ndev->cur_num_vqs = 2 * cur_qps;
+
 	return err;
 }
 
@@ -1529,11 +1530,27 @@
 
 	switch (cmd) {
 	case VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET:
+		/* This mq feature check aligns with pre-existing userspace
+		 * implementation.
+		 *
+		 * Without it, an untrusted driver could fake a multiqueue config
+		 * request down to a non-mq device that may cause kernel to
+		 * panic due to uninitialized resources for extra vqs. Even with
+		 * a well behaving guest driver, it is not expected to allow
+		 * changing the number of vqs on a non-mq device.
+		 */
+		if (!MLX5_FEATURE(mvdev, VIRTIO_NET_F_MQ))
+			break;
+
 		read = vringh_iov_pull_iotlb(&cvq->vring, &cvq->riov, (void *)&mq, sizeof(mq));
 		if (read != sizeof(mq))
 			break;
 
 		newqps = mlx5vdpa16_to_cpu(mvdev, mq.virtqueue_pairs);
+		if (newqps < VIRTIO_NET_CTRL_MQ_VQ_PAIRS_MIN ||
+		    newqps > mlx5_vdpa_max_qps(mvdev->max_vqs))
+			break;
+
 		if (ndev->cur_num_vqs == 2 * newqps) {
 			status = VIRTIO_NET_OK;
 			break;
@@ -1557,22 +1574,22 @@
 {
 	virtio_net_ctrl_ack status = VIRTIO_NET_ERR;
 	struct virtio_net_ctrl_hdr ctrl;
-	struct mlx5_ctrl_wq_ent *wqent;
+	struct mlx5_vdpa_wq_ent *wqent;
 	struct mlx5_vdpa_dev *mvdev;
 	struct mlx5_control_vq *cvq;
 	struct mlx5_vdpa_net *ndev;
 	size_t read, write;
 	int err;
 
-	wqent = container_of(work, struct mlx5_ctrl_wq_ent, work);
+	wqent = container_of(work, struct mlx5_vdpa_wq_ent, work);
 	mvdev = wqent->mvdev;
 	ndev = to_mlx5_vdpa_ndev(mvdev);
 	cvq = &mvdev->cvq;
 	if (!(ndev->mvdev.actual_features & BIT_ULL(VIRTIO_NET_F_CTRL_VQ)))
-		goto out;
+		return;
 
 	if (!cvq->ready)
-		goto out;
+		return;
 
 	while (true) {
 		err = vringh_getdesc_iotlb(&cvq->vring, &cvq->riov, &cvq->wiov, &cvq->head,
@@ -1606,9 +1623,10 @@
 
 		if (vringh_need_notify_iotlb(&cvq->vring))
 			vringh_notify(&cvq->vring);
+
+		queue_work(mvdev->wq, &wqent->work);
+		break;
 	}
-out:
-	kfree(wqent);
 }
 
 static void mlx5_vdpa_kick_vq(struct vdpa_device *vdev, u16 idx)
@@ -1616,22 +1634,15 @@
 	struct mlx5_vdpa_dev *mvdev = to_mvdev(vdev);
 	struct mlx5_vdpa_net *ndev = to_mlx5_vdpa_ndev(mvdev);
 	struct mlx5_vdpa_virtqueue *mvq;
-	struct mlx5_ctrl_wq_ent *wqent;
 
 	if (!is_index_valid(mvdev, idx))
 		return;
 
 	if (unlikely(is_ctrl_vq_idx(mvdev, idx))) {
-		if (!mvdev->cvq.ready)
-			return;
-
-		wqent = kzalloc(sizeof(*wqent), GFP_ATOMIC);
-		if (!wqent)
+		if (!mvdev->wq || !mvdev->cvq.ready)
 			return;
 
-		wqent->mvdev = mvdev;
-		INIT_WORK(&wqent->work, mlx5_cvq_kick_handler);
-		queue_work(mvdev->wq, &wqent->work);
+		queue_work(mvdev->wq, &ndev->cvq_ent.work);
 		return;
 	}
 
@@ -1672,9 +1683,16 @@
 	struct mlx5_vdpa_net *ndev = to_mlx5_vdpa_ndev(mvdev);
 	struct mlx5_vdpa_virtqueue *mvq;
 
-	if (!is_index_valid(mvdev, idx) || is_ctrl_vq_idx(mvdev, idx))
+	if (!is_index_valid(mvdev, idx))
 		return;
 
+        if (is_ctrl_vq_idx(mvdev, idx)) {
+                struct mlx5_control_vq *cvq = &mvdev->cvq;
+
+                cvq->vring.vring.num = num;
+                return;
+        }
+
 	mvq = &ndev->vqs[idx];
 	mvq->num_ent = num;
 }
@@ -1685,6 +1703,8 @@
 	struct mlx5_vdpa_net *ndev = to_mlx5_vdpa_ndev(mvdev);
 
 	ndev->event_cbs[idx] = *cb;
+	if (is_ctrl_vq_idx(mvdev, idx))
+		mvdev->cvq.event_cb = *cb;
 }
 
 static void mlx5_cvq_notify(struct vringh *vring)
@@ -1852,23 +1872,37 @@
 	ndev->mvdev.mlx_features |= BIT_ULL(VIRTIO_NET_F_CTRL_VQ);
 	ndev->mvdev.mlx_features |= BIT_ULL(VIRTIO_NET_F_CTRL_MAC_ADDR);
 	ndev->mvdev.mlx_features |= BIT_ULL(VIRTIO_NET_F_MQ);
+	ndev->mvdev.mlx_features |= BIT_ULL(VIRTIO_NET_F_STATUS);
 
 	print_features(mvdev, ndev->mvdev.mlx_features, false);
 	return ndev->mvdev.mlx_features;
 }
 
-static int verify_min_features(struct mlx5_vdpa_dev *mvdev, u64 features)
+static int verify_driver_features(struct mlx5_vdpa_dev *mvdev, u64 features)
 {
+	/* Minimum features to expect */
 	if (!(features & BIT_ULL(VIRTIO_F_ACCESS_PLATFORM)))
 		return -EOPNOTSUPP;
 
+	/* Double check features combination sent down by the driver.
+	 * Fail invalid features due to absence of the depended feature.
+	 *
+	 * Per VIRTIO v1.1 specification, section 5.1.3.1 Feature bit
+	 * requirements: "VIRTIO_NET_F_MQ Requires VIRTIO_NET_F_CTRL_VQ".
+	 * By failing the invalid features sent down by untrusted drivers,
+	 * we're assured the assumption made upon is_index_valid() and
+	 * is_ctrl_vq_idx() will not be compromised.
+	 */
+	if ((features & (BIT_ULL(VIRTIO_NET_F_MQ) | BIT_ULL(VIRTIO_NET_F_CTRL_VQ))) ==
+            BIT_ULL(VIRTIO_NET_F_MQ))
+		return -EINVAL;
+
 	return 0;
 }
 
 static int setup_virtqueues(struct mlx5_vdpa_dev *mvdev)
 {
 	struct mlx5_vdpa_net *ndev = to_mlx5_vdpa_ndev(mvdev);
-	struct mlx5_control_vq *cvq = &mvdev->cvq;
 	int err;
 	int i;
 
@@ -1878,16 +1912,6 @@
 			goto err_vq;
 	}
 
-	if (mvdev->actual_features & BIT_ULL(VIRTIO_NET_F_CTRL_VQ)) {
-		err = vringh_init_iotlb(&cvq->vring, mvdev->actual_features,
-					MLX5_CVQ_MAX_ENT, false,
-					(struct vring_desc *)(uintptr_t)cvq->desc_addr,
-					(struct vring_avail *)(uintptr_t)cvq->driver_addr,
-					(struct vring_used *)(uintptr_t)cvq->device_addr);
-		if (err)
-			goto err_vq;
-	}
-
 	return 0;
 
 err_vq:
@@ -1937,7 +1961,7 @@
 
 	print_features(mvdev, features, true);
 
-	err = verify_min_features(mvdev, features);
+	err = verify_driver_features(mvdev, features);
 	if (err)
 		return err;
 
@@ -1950,8 +1974,10 @@
 
 static void mlx5_vdpa_set_config_cb(struct vdpa_device *vdev, struct vdpa_callback *cb)
 {
-	/* not implemented */
-	mlx5_vdpa_warn(to_mvdev(vdev), "set config callback not supported\n");
+	struct mlx5_vdpa_dev *mvdev = to_mvdev(vdev);
+	struct mlx5_vdpa_net *ndev = to_mlx5_vdpa_ndev(mvdev);
+
+	ndev->config_cb = *cb;
 }
 
 #define MLX5_VDPA_MAX_VQ_ENTRIES 256
@@ -2152,6 +2178,26 @@
 	ndev->mvdev.cvq.ready = false;
 }
 
+static int setup_cvq_vring(struct mlx5_vdpa_dev *mvdev)
+{
+	struct mlx5_control_vq *cvq = &mvdev->cvq;
+	int err = 0;
+
+	if (mvdev->actual_features & BIT_ULL(VIRTIO_NET_F_CTRL_VQ)) {
+		u16 idx = cvq->vring.last_avail_idx;
+
+		err = vringh_init_iotlb(&cvq->vring, mvdev->actual_features,
+					cvq->vring.vring.num, false,
+					(struct vring_desc *)(uintptr_t)cvq->desc_addr,
+					(struct vring_avail *)(uintptr_t)cvq->driver_addr,
+					(struct vring_used *)(uintptr_t)cvq->device_addr);
+
+		if (!err)
+			cvq->vring.last_avail_idx = cvq->vring.last_used_idx = idx;
+	}
+	return err;
+}
+
 static void mlx5_vdpa_set_status(struct vdpa_device *vdev, u8 status)
 {
 	struct mlx5_vdpa_dev *mvdev = to_mvdev(vdev);
@@ -2162,6 +2208,11 @@
 
 	if ((status ^ ndev->mvdev.status) & VIRTIO_CONFIG_S_DRIVER_OK) {
 		if (status & VIRTIO_CONFIG_S_DRIVER_OK) {
+			err = setup_cvq_vring(mvdev);
+			if (err) {
+				mlx5_vdpa_warn(mvdev, "failed to setup control VQ vring\n");
+				goto err_setup;
+			}
 			err = setup_driver(mvdev);
 			if (err) {
 				mlx5_vdpa_warn(mvdev, "failed to setup driver\n");
@@ -2192,7 +2243,6 @@
 	clear_vqs_ready(ndev);
 	mlx5_vdpa_destroy_mr(&ndev->mvdev);
 	ndev->mvdev.status = 0;
-	ndev->mvdev.mlx_features = 0;
 	memset(ndev->event_cbs, 0, sizeof(ndev->event_cbs));
 	ndev->mvdev.actual_features = 0;
 	++mvdev->generation;
@@ -2404,6 +2454,82 @@
 	struct mlx5_vdpa_net *ndev;
 };
 
+static u8 query_vport_state(struct mlx5_core_dev *mdev, u8 opmod, u16 vport)
+{
+	u32 out[MLX5_ST_SZ_DW(query_vport_state_out)] = {};
+	u32 in[MLX5_ST_SZ_DW(query_vport_state_in)] = {};
+	int err;
+
+	MLX5_SET(query_vport_state_in, in, opcode, MLX5_CMD_OP_QUERY_VPORT_STATE);
+	MLX5_SET(query_vport_state_in, in, op_mod, opmod);
+	MLX5_SET(query_vport_state_in, in, vport_number, vport);
+	if (vport)
+		MLX5_SET(query_vport_state_in, in, other_vport, 1);
+
+	err = mlx5_cmd_exec_inout(mdev, query_vport_state, in, out);
+	if (err)
+		return 0;
+
+	return MLX5_GET(query_vport_state_out, out, state);
+}
+
+static bool get_link_state(struct mlx5_vdpa_dev *mvdev)
+{
+	if (query_vport_state(mvdev->mdev, MLX5_VPORT_STATE_OP_MOD_VNIC_VPORT, 0) ==
+	    VPORT_STATE_UP)
+		return true;
+
+	return false;
+}
+
+static void update_carrier(struct work_struct *work)
+{
+	struct mlx5_vdpa_wq_ent *wqent;
+	struct mlx5_vdpa_dev *mvdev;
+	struct mlx5_vdpa_net *ndev;
+
+	wqent = container_of(work, struct mlx5_vdpa_wq_ent, work);
+	mvdev = wqent->mvdev;
+	ndev = to_mlx5_vdpa_ndev(mvdev);
+	if (get_link_state(mvdev))
+		ndev->config.status |= cpu_to_mlx5vdpa16(mvdev, VIRTIO_NET_S_LINK_UP);
+	else
+		ndev->config.status &= cpu_to_mlx5vdpa16(mvdev, ~VIRTIO_NET_S_LINK_UP);
+
+	if (ndev->config_cb.callback)
+		ndev->config_cb.callback(ndev->config_cb.private);
+
+	kfree(wqent);
+}
+
+static int event_handler(struct notifier_block *nb, unsigned long event, void *param)
+{
+	struct mlx5_vdpa_net *ndev = container_of(nb, struct mlx5_vdpa_net, nb);
+	struct mlx5_eqe *eqe = param;
+	int ret = NOTIFY_DONE;
+	struct mlx5_vdpa_wq_ent *wqent;
+
+	if (event == MLX5_EVENT_TYPE_PORT_CHANGE) {
+		switch (eqe->sub_type) {
+		case MLX5_PORT_CHANGE_SUBTYPE_DOWN:
+		case MLX5_PORT_CHANGE_SUBTYPE_ACTIVE:
+			wqent = kzalloc(sizeof(*wqent), GFP_ATOMIC);
+			if (!wqent)
+				return NOTIFY_DONE;
+
+			wqent->mvdev = &ndev->mvdev;
+			INIT_WORK(&wqent->work, update_carrier);
+			queue_work(ndev->mvdev.wq, &wqent->work);
+			ret = NOTIFY_OK;
+			break;
+		default:
+			return NOTIFY_DONE;
+		}
+		return ret;
+	}
+	return ret;
+}
+
 static int mlx5_vdpa_dev_add(struct vdpa_mgmt_dev *v_mdev, const char *name)
 {
 	struct mlx5_vdpa_mgmtdev *mgtdev = container_of(v_mdev, struct mlx5_vdpa_mgmtdev, mgtdev);
@@ -2448,6 +2574,11 @@
 	if (err)
 		goto err_mtu;
 
+	if (get_link_state(mvdev))
+		ndev->config.status |= cpu_to_mlx5vdpa16(mvdev, VIRTIO_NET_S_LINK_UP);
+	else
+		ndev->config.status &= cpu_to_mlx5vdpa16(mvdev, ~VIRTIO_NET_S_LINK_UP);
+
 	if (!is_zero_ether_addr(config->mac)) {
 		pfmdev = pci_get_drvdata(pci_physfn(mdev->pdev));
 		err = mlx5_mpfs_add_mac(pfmdev, config->mac);
@@ -2473,12 +2604,16 @@
 	if (err)
 		goto err_mr;
 
-	mvdev->wq = create_singlethread_workqueue("mlx5_vdpa_ctrl_wq");
+	ndev->cvq_ent.mvdev = mvdev;
+	INIT_WORK(&ndev->cvq_ent.work, mlx5_cvq_kick_handler);
+	mvdev->wq = create_singlethread_workqueue("mlx5_vdpa_wq");
 	if (!mvdev->wq) {
 		err = -ENOMEM;
 		goto err_res2;
 	}
 
+	ndev->nb.notifier_call = event_handler;
+	mlx5_notifier_register(mdev, &ndev->nb);
 	ndev->cur_num_vqs = 2 * mlx5_vdpa_max_qps(max_vqs);
 	mvdev->vdev.mdev = &mgtdev->mgtdev;
 	err = _vdpa_register_device(&mvdev->vdev, ndev->cur_num_vqs + 1);
@@ -2509,8 +2644,13 @@
 {
 	struct mlx5_vdpa_mgmtdev *mgtdev = container_of(v_mdev, struct mlx5_vdpa_mgmtdev, mgtdev);
 	struct mlx5_vdpa_dev *mvdev = to_mvdev(dev);
+	struct mlx5_vdpa_net *ndev = to_mlx5_vdpa_ndev(mvdev);
+	struct workqueue_struct *wq;
 
-	destroy_workqueue(mvdev->wq);
+	mlx5_notifier_unregister(mvdev->mdev, &ndev->nb);
+	wq = mvdev->wq;
+	mvdev->wq = NULL;
+	destroy_workqueue(wq);
 	_vdpa_unregister_device(dev);
 	mgtdev->ndev = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/vdpa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/vdpa.c
@@ -353,7 +353,8 @@
 		goto msg_err;
 
 	while (mdev->id_table[i].device) {
-		supported_classes |= BIT(mdev->id_table[i].device);
+		if (mdev->id_table[i].device <= 63)
+			supported_classes |= BIT_ULL(mdev->id_table[i].device);
 		i++;
 	}
 
@@ -557,14 +558,19 @@
 		goto mdev_err;
 	}
 	err = vdpa_dev_fill(vdev, msg, info->snd_portid, info->snd_seq, 0, info->extack);
-	if (!err)
-		err = genlmsg_reply(msg, info);
+	if (err)
+		goto mdev_err;
+
+	err = genlmsg_reply(msg, info);
+	put_device(dev);
+	mutex_unlock(&vdpa_dev_mutex);
+	return err;
+
 mdev_err:
 	put_device(dev);
 err:
 	mutex_unlock(&vdpa_dev_mutex);
-	if (err)
-		nlmsg_free(msg);
+	nlmsg_free(msg);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/vdpa_sim/vdpa_sim.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/vdpa_sim/vdpa_sim.c
@@ -65,15 +65,27 @@
 static void vdpasim_queue_ready(struct vdpasim *vdpasim, unsigned int idx)
 {
 	struct vdpasim_virtqueue *vq = &vdpasim->vqs[idx];
+	uint16_t last_avail_idx = vq->vring.last_avail_idx;
 
-	vringh_init_iotlb(&vq->vring, vdpasim->dev_attr.supported_features,
-			  VDPASIM_QUEUE_MAX, false,
+	vringh_init_iotlb(&vq->vring, vdpasim->features, vq->num, false,
 			  (struct vring_desc *)(uintptr_t)vq->desc_addr,
 			  (struct vring_avail *)
 			  (uintptr_t)vq->driver_addr,
 			  (struct vring_used *)
 			  (uintptr_t)vq->device_addr);
 
+	vq->vring.last_avail_idx = last_avail_idx;
+
+	/*
+	 * Since vdpa_sim does not support receive inflight descriptors as a
+	 * destination of a migration, let's set both avail_idx and used_idx
+	 * the same at vq start.  This is how vhost-user works in a
+	 * VHOST_SET_VRING_BASE call.
+	 *
+	 * Although the simple fix is to set last_used_idx at
+	 * vdpasim_set_vq_state, it would be reset at vdpasim_queue_ready.
+	 */
+	vq->vring.last_used_idx = last_avail_idx;
 	vq->vring.notify = vdpasim_vq_notify;
 }
 
@@ -353,11 +365,14 @@
 {
 	struct vdpasim *vdpasim = vdpa_to_sim(vdpa);
 	struct vdpasim_virtqueue *vq = &vdpasim->vqs[idx];
+	bool old_ready;
 
 	spin_lock(&vdpasim->lock);
+	old_ready = vq->ready;
 	vq->ready = ready;
-	if (vq->ready)
+	if (vq->ready && !old_ready) {
 		vdpasim_queue_ready(vdpasim, idx);
+	}
 	spin_unlock(&vdpasim->lock);
 }
 
@@ -591,8 +606,11 @@
 		vringh_kiov_cleanup(&vdpasim->vqs[i].in_iov);
 	}
 
-	put_iova_domain(&vdpasim->iova);
-	iova_cache_put();
+	if (vdpa_get_dma_dev(vdpa)) {
+		put_iova_domain(&vdpasim->iova);
+		iova_cache_put();
+	}
+
 	kvfree(vdpasim->buffer);
 	if (vdpasim->iommu)
 		vhost_iotlb_free(vdpasim->iommu);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/vdpa_sim/vdpa_sim_blk.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/vdpa_sim/vdpa_sim_blk.c
@@ -308,8 +308,10 @@
 	int ret;
 
 	ret = device_register(&vdpasim_blk_mgmtdev);
-	if (ret)
+	if (ret) {
+		put_device(&vdpasim_blk_mgmtdev);
 		return ret;
+	}
 
 	ret = vdpa_mgmtdev_register(&mgmt_dev);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/vdpa_sim/vdpa_sim_net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/vdpa_sim/vdpa_sim_net.c
@@ -194,8 +194,10 @@
 	}
 
 	ret = device_register(&vdpasim_net_mgmtdev);
-	if (ret)
+	if (ret) {
+		put_device(&vdpasim_net_mgmtdev);
 		return ret;
+	}
 
 	ret = vdpa_mgmtdev_register(&mgmt_dev);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/vdpa_user/iova_domain.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/vdpa_user/iova_domain.c
@@ -302,7 +302,7 @@
 		iova_len = roundup_pow_of_two(iova_len);
 	iova_pfn = alloc_iova_fast(iovad, iova_len, limit >> shift, true);
 
-	return iova_pfn << shift;
+	return (dma_addr_t)iova_pfn << shift;
 }
 
 static void vduse_domain_free_iova(struct iova_domain *iovad,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/vdpa_user/vduse_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/vdpa_user/vduse_dev.c
@@ -8,6 +8,7 @@
  *
  */
 
+#include "linux/virtio_net.h"
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/cdev.h>
@@ -26,6 +27,7 @@
 #include <uapi/linux/virtio_config.h>
 #include <uapi/linux/virtio_ids.h>
 #include <uapi/linux/virtio_blk.h>
+#include <uapi/linux/virtio_ring.h>
 #include <linux/mod_devicetable.h>
 
 #include "iova_domain.h"
@@ -655,9 +657,15 @@
 {
 	struct vduse_dev *dev = vdpa_to_vduse(vdpa);
 
-	if (len > dev->config_size - offset)
+	/* Initialize the buffer in case of partial copy. */
+	memset(buf, 0, len);
+
+	if (offset > dev->config_size)
 		return;
 
+	if (len > dev->config_size - offset)
+		len = dev->config_size - offset;
+
 	memcpy(buf, dev->config + offset, len);
 }
 
@@ -873,10 +881,10 @@
 {
 	struct vduse_dev *dev = container_of(work, struct vduse_dev, inject);
 
-	spin_lock_irq(&dev->irq_lock);
+	spin_lock_bh(&dev->irq_lock);
 	if (dev->config_cb.callback)
 		dev->config_cb.callback(dev->config_cb.private);
-	spin_unlock_irq(&dev->irq_lock);
+	spin_unlock_bh(&dev->irq_lock);
 }
 
 static void vduse_vq_irq_inject(struct work_struct *work)
@@ -884,10 +892,10 @@
 	struct vduse_virtqueue *vq = container_of(work,
 					struct vduse_virtqueue, inject);
 
-	spin_lock_irq(&vq->irq_lock);
+	spin_lock_bh(&vq->irq_lock);
 	if (vq->ready && vq->cb.callback)
 		vq->cb.callback(vq->cb.private);
-	spin_unlock_irq(&vq->irq_lock);
+	spin_unlock_bh(&vq->irq_lock);
 }
 
 static int vduse_dev_queue_irq_work(struct vduse_dev *dev,
@@ -975,7 +983,8 @@
 			break;
 
 		ret = -EINVAL;
-		if (config.length == 0 ||
+		if (config.offset > dev->config_size ||
+		    config.length == 0 ||
 		    config.length > dev->config_size - config.offset)
 			break;
 
@@ -1220,13 +1229,17 @@
 	return false;
 }
 
-static bool features_is_valid(u64 features)
+static bool features_is_valid(struct vduse_dev_config *config)
 {
-	if (!(features & (1ULL << VIRTIO_F_ACCESS_PLATFORM)))
+	if (!(config->features & BIT_ULL(VIRTIO_F_ACCESS_PLATFORM)))
 		return false;
 
 	/* Now we only support read-only configuration space */
-	if (features & (1ULL << VIRTIO_BLK_F_CONFIG_WCE))
+	if ((config->device_id == VIRTIO_ID_BLOCK) &&
+			(config->features & BIT_ULL(VIRTIO_BLK_F_CONFIG_WCE)))
+		return false;
+	else if ((config->device_id == VIRTIO_ID_NET) &&
+			(config->features & BIT_ULL(VIRTIO_NET_F_CTRL_VQ)))
 		return false;
 
 	return true;
@@ -1244,10 +1257,16 @@
 	if (config->config_size > PAGE_SIZE)
 		return false;
 
+	if (config->vq_num > 0xffff)
+		return false;
+
+	if (!config->name[0])
+		return false;
+
 	if (!device_is_allowed(config->device_id))
 		return false;
 
-	if (!features_is_valid(config->features))
+	if (!features_is_valid(config))
 		return false;
 
 	return true;
@@ -1334,9 +1353,9 @@
 
 	dev->minor = ret;
 	dev->msg_timeout = VDUSE_MSG_DEFAULT_TIMEOUT;
-	dev->dev = device_create(vduse_class, NULL,
-				 MKDEV(MAJOR(vduse_major), dev->minor),
-				 dev, "%s", config->name);
+	dev->dev = device_create_with_groups(vduse_class, NULL,
+				MKDEV(MAJOR(vduse_major), dev->minor),
+				dev, vduse_dev_groups, "%s", config->name);
 	if (IS_ERR(dev->dev)) {
 		ret = PTR_ERR(dev->dev);
 		goto err_dev;
@@ -1464,16 +1483,12 @@
 	return kasprintf(GFP_KERNEL, "vduse/%s", dev_name(dev));
 }
 
-static void vduse_mgmtdev_release(struct device *dev)
-{
-}
-
-static struct device vduse_mgmtdev = {
-	.init_name = "vduse",
-	.release = vduse_mgmtdev_release,
+struct vduse_mgmt_dev {
+	struct vdpa_mgmt_dev mgmt_dev;
+	struct device dev;
 };
 
-static struct vdpa_mgmt_dev mgmt_dev;
+static struct vduse_mgmt_dev *vduse_mgmt;
 
 static int vduse_dev_init_vdpa(struct vduse_dev *dev, const char *name)
 {
@@ -1498,7 +1513,7 @@
 	}
 	set_dma_ops(&vdev->vdpa.dev, &vduse_dev_dma_ops);
 	vdev->vdpa.dma_dev = &vdev->vdpa.dev;
-	vdev->vdpa.mdev = &mgmt_dev;
+	vdev->vdpa.mdev = &vduse_mgmt->mgmt_dev;
 
 	return 0;
 }
@@ -1543,34 +1558,52 @@
 	{ 0 },
 };
 
-static struct vdpa_mgmt_dev mgmt_dev = {
-	.device = &vduse_mgmtdev,
-	.id_table = id_table,
-	.ops = &vdpa_dev_mgmtdev_ops,
-};
+static void vduse_mgmtdev_release(struct device *dev)
+{
+	struct vduse_mgmt_dev *mgmt_dev;
+
+	mgmt_dev = container_of(dev, struct vduse_mgmt_dev, dev);
+	kfree(mgmt_dev);
+}
 
 static int vduse_mgmtdev_init(void)
 {
 	int ret;
 
-	ret = device_register(&vduse_mgmtdev);
-	if (ret)
+	vduse_mgmt = kzalloc(sizeof(*vduse_mgmt), GFP_KERNEL);
+	if (!vduse_mgmt)
+		return -ENOMEM;
+
+	ret = dev_set_name(&vduse_mgmt->dev, "vduse");
+	if (ret) {
+		kfree(vduse_mgmt);
 		return ret;
+	}
+
+	vduse_mgmt->dev.release = vduse_mgmtdev_release;
 
-	ret = vdpa_mgmtdev_register(&mgmt_dev);
+	ret = device_register(&vduse_mgmt->dev);
 	if (ret)
-		goto err;
+		goto dev_reg_err;
 
-	return 0;
-err:
-	device_unregister(&vduse_mgmtdev);
+	vduse_mgmt->mgmt_dev.id_table = id_table;
+	vduse_mgmt->mgmt_dev.ops = &vdpa_dev_mgmtdev_ops;
+	vduse_mgmt->mgmt_dev.device = &vduse_mgmt->dev;
+	ret = vdpa_mgmtdev_register(&vduse_mgmt->mgmt_dev);
+	if (ret)
+		device_unregister(&vduse_mgmt->dev);
+
+	return ret;
+
+dev_reg_err:
+	put_device(&vduse_mgmt->dev);
 	return ret;
 }
 
 static void vduse_mgmtdev_exit(void)
 {
-	vdpa_mgmtdev_unregister(&mgmt_dev);
-	device_unregister(&vduse_mgmtdev);
+	vdpa_mgmtdev_unregister(&vduse_mgmt->mgmt_dev);
+	device_unregister(&vduse_mgmt->dev);
 }
 
 static int vduse_init(void)
@@ -1583,7 +1616,6 @@
 		return PTR_ERR(vduse_class);
 
 	vduse_class->devnode = vduse_devnode;
-	vduse_class->dev_groups = vduse_dev_groups;
 
 	ret = alloc_chrdev_region(&vduse_major, 0, VDUSE_DEV_MAX, "vduse");
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vdpa/virtio_pci/vp_vdpa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vdpa/virtio_pci/vp_vdpa.c
@@ -513,8 +513,8 @@
 {
 	struct vp_vdpa *vp_vdpa = pci_get_drvdata(pdev);
 
-	vdpa_unregister_device(&vp_vdpa->vdpa);
 	vp_modern_remove(&vp_vdpa->mdev);
+	vdpa_unregister_device(&vp_vdpa->vdpa);
 }
 
 static struct pci_driver vp_vdpa_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/fsl-mc/vfio_fsl_mc_intr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/fsl-mc/vfio_fsl_mc_intr.c
@@ -142,13 +142,14 @@
 	irq = &vdev->mc_irqs[index];
 
 	if (flags & VFIO_IRQ_SET_DATA_NONE) {
-		vfio_fsl_mc_irq_handler(hwirq, irq);
+		if (irq->trigger)
+			eventfd_signal(irq->trigger, 1);
 
 	} else if (flags & VFIO_IRQ_SET_DATA_BOOL) {
 		u8 trigger = *(u8 *)data;
 
-		if (trigger)
-			vfio_fsl_mc_irq_handler(hwirq, irq);
+		if (trigger && irq->trigger)
+			eventfd_signal(irq->trigger, 1);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/Kconfig
@@ -43,4 +43,16 @@
 
 	  To enable Intel IGD assignment through vfio-pci, say Y.
 endif
+
+config VFIO_PCI_ZDEV_KVM
+	bool "VFIO PCI extensions for s390x KVM passthrough"
+	depends on S390 && KVM
+	default y
+	help
+	  Support s390x-specific extensions to enable support for enhancements
+	  to KVM passthrough capabilities, such as interpretive execution of
+	  zPCI instructions.
+
+	  To enable s390x KVM vfio-pci extensions, say Y.
+
 endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/Makefile
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 
 vfio-pci-core-y := vfio_pci_core.o vfio_pci_intrs.o vfio_pci_rdwr.o vfio_pci_config.o
-vfio-pci-core-$(CONFIG_S390) += vfio_pci_zdev.o
+vfio-pci-core-$(CONFIG_VFIO_PCI_ZDEV_KVM) += vfio_pci_zdev.o
 obj-$(CONFIG_VFIO_PCI_CORE) += vfio-pci-core.o
 
 vfio-pci-y := vfio_pci.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/vfio_pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/vfio_pci.c
@@ -71,6 +71,8 @@
 		case PCI_DEVICE_ID_INTEL_QAT_C62X_VF:
 		case PCI_DEVICE_ID_INTEL_QAT_DH895XCC:
 		case PCI_DEVICE_ID_INTEL_QAT_DH895XCC_VF:
+		case PCI_DEVICE_ID_INTEL_DSA_SPR0:
+		case PCI_DEVICE_ID_INTEL_IAX_SPR0:
 			return true;
 		default:
 			return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/vfio_pci_config.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/vfio_pci_config.c
@@ -312,6 +312,10 @@
 	return count;
 }
 
+static struct perm_bits direct_ro_perms = {
+	.readfn = vfio_direct_config_read,
+};
+
 /* Default capability regions to read-only, no-virtualization */
 static struct perm_bits cap_perms[PCI_CAP_ID_MAX + 1] = {
 	[0 ... PCI_CAP_ID_MAX] = { .readfn = vfio_direct_config_read }
@@ -1840,9 +1844,17 @@
 		cap_start = *ppos;
 	} else {
 		if (*ppos >= PCI_CFG_SPACE_SIZE) {
-			WARN_ON(cap_id > PCI_EXT_CAP_ID_MAX);
+			/*
+			 * We can get a cap_id that exceeds PCI_EXT_CAP_ID_MAX
+			 * if we're hiding an unknown capability at the start
+			 * of the extended capability list.  Use default, ro
+			 * access, which will virtualize the id and next values.
+			 */
+			if (cap_id > PCI_EXT_CAP_ID_MAX)
+				perm = &direct_ro_perms;
+			else
+				perm = &ecap_perms[cap_id];
 
-			perm = &ecap_perms[cap_id];
 			cap_start = vfio_find_cap_start(vdev, *ppos);
 		} else {
 			WARN_ON(cap_id > PCI_CAP_ID_MAX);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/vfio_pci_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/vfio_pci_core.c
@@ -36,6 +36,10 @@
 static bool disable_vga;
 static bool disable_idle_d3;
 
+/* List of PF's that vfio_pci_core_sriov_configure() has been called on */
+static DEFINE_MUTEX(vfio_pci_sriov_pfs_mutex);
+static LIST_HEAD(vfio_pci_sriov_pfs);
+
 static inline bool vfio_vga_disabled(void)
 {
 #ifdef CONFIG_VFIO_PCI_VGA
@@ -228,6 +232,19 @@
 	if (!ret) {
 		/* D3 might be unsupported via quirk, skip unless in D3 */
 		if (needs_save && pdev->current_state >= PCI_D3hot) {
+			/*
+			 * The current PCI state will be saved locally in
+			 * 'pm_save' during the D3hot transition. When the
+			 * device state is changed to D0 again with the current
+			 * function, then pci_store_saved_state() will restore
+			 * the state and will free the memory pointed by
+			 * 'pm_save'. There are few cases where the PCI power
+			 * state can be changed to D0 without the involvement
+			 * of the driver. For these cases, free the earlier
+			 * allocated memory first before overwriting 'pm_save'
+			 * to prevent the memory leak.
+			 */
+			kfree(vdev->pm_save);
 			vdev->pm_save = pci_store_saved_state(pdev);
 		} else if (needs_restore) {
 			pci_load_and_free_saved_state(pdev, &vdev->pm_save);
@@ -282,8 +299,17 @@
 		pci_write_config_word(pdev, PCI_COMMAND, cmd);
 	}
 
+	ret = vfio_pci_zdev_open_device(vdev);
+	if (ret) {
+		kfree(vdev->pci_saved_state);
+		vdev->pci_saved_state = NULL;
+		pci_disable_device(pdev);
+		return ret;
+	}
+
 	ret = vfio_config_init(vdev);
 	if (ret) {
+		vfio_pci_zdev_close_device(vdev);
 		kfree(vdev->pci_saved_state);
 		vdev->pci_saved_state = NULL;
 		pci_disable_device(pdev);
@@ -322,6 +348,17 @@
 	/* For needs_reset */
 	lockdep_assert_held(&vdev->vdev.dev_set->lock);
 
+	/*
+	 * This function can be invoked while the power state is non-D0.
+	 * This function calls __pci_reset_function_locked() which internally
+	 * can use pci_pm_reset() for the function reset. pci_pm_reset() will
+	 * fail if the power state is non-D0. Also, for the devices which
+	 * have NoSoftRst-, the reset function can cause the PCI config space
+	 * reset without restoring the original state (saved locally in
+	 * 'vdev->pm_save').
+	 */
+	vfio_pci_set_power_state(vdev, PCI_D0);
+
 	/* Stop the device from further DMA */
 	pci_clear_master(pdev);
 
@@ -367,6 +404,8 @@
 
 	vdev->needs_reset = true;
 
+	vfio_pci_zdev_close_device(vdev);
+
 	/*
 	 * If we have saved state, restore it.  If we can reset the device,
 	 * even better.  Resetting with current state seems better than
@@ -410,47 +449,17 @@
 }
 EXPORT_SYMBOL_GPL(vfio_pci_core_disable);
 
-static struct vfio_pci_core_device *get_pf_vdev(struct vfio_pci_core_device *vdev)
-{
-	struct pci_dev *physfn = pci_physfn(vdev->pdev);
-	struct vfio_device *pf_dev;
-
-	if (!vdev->pdev->is_virtfn)
-		return NULL;
-
-	pf_dev = vfio_device_get_from_dev(&physfn->dev);
-	if (!pf_dev)
-		return NULL;
-
-	if (pci_dev_driver(physfn) != pci_dev_driver(vdev->pdev)) {
-		vfio_device_put(pf_dev);
-		return NULL;
-	}
-
-	return container_of(pf_dev, struct vfio_pci_core_device, vdev);
-}
-
-static void vfio_pci_vf_token_user_add(struct vfio_pci_core_device *vdev, int val)
-{
-	struct vfio_pci_core_device *pf_vdev = get_pf_vdev(vdev);
-
-	if (!pf_vdev)
-		return;
-
-	mutex_lock(&pf_vdev->vf_token->lock);
-	pf_vdev->vf_token->users += val;
-	WARN_ON(pf_vdev->vf_token->users < 0);
-	mutex_unlock(&pf_vdev->vf_token->lock);
-
-	vfio_device_put(&pf_vdev->vdev);
-}
-
 void vfio_pci_core_close_device(struct vfio_device *core_vdev)
 {
 	struct vfio_pci_core_device *vdev =
 		container_of(core_vdev, struct vfio_pci_core_device, vdev);
 
-	vfio_pci_vf_token_user_add(vdev, -1);
+	if (vdev->sriov_pf_core_dev) {
+		mutex_lock(&vdev->sriov_pf_core_dev->vf_token->lock);
+		WARN_ON(!vdev->sriov_pf_core_dev->vf_token->users);
+		vdev->sriov_pf_core_dev->vf_token->users--;
+		mutex_unlock(&vdev->sriov_pf_core_dev->vf_token->lock);
+	}
 	vfio_spapr_pci_eeh_release(vdev->pdev);
 	vfio_pci_core_disable(vdev);
 
@@ -471,7 +480,12 @@
 {
 	vfio_pci_probe_mmaps(vdev);
 	vfio_spapr_pci_eeh_open(vdev->pdev);
-	vfio_pci_vf_token_user_add(vdev, 1);
+
+	if (vdev->sriov_pf_core_dev) {
+		mutex_lock(&vdev->sriov_pf_core_dev->vf_token->lock);
+		vdev->sriov_pf_core_dev->vf_token->users++;
+		mutex_unlock(&vdev->sriov_pf_core_dev->vf_token->lock);
+	}
 }
 EXPORT_SYMBOL_GPL(vfio_pci_core_finish_enable);
 
@@ -921,6 +935,19 @@
 			return -EINVAL;
 
 		vfio_pci_zap_and_down_write_memory_lock(vdev);
+
+		/*
+		 * This function can be invoked while the power state is non-D0.
+		 * If pci_try_reset_function() has been called while the power
+		 * state is non-D0, then pci_try_reset_function() will
+		 * internally set the power state to D0 without vfio driver
+		 * involvement. For the devices which have NoSoftRst-, the
+		 * reset function can cause the PCI config space reset without
+		 * restoring the original state (saved locally in
+		 * 'vdev->pm_save').
+		 */
+		vfio_pci_set_power_state(vdev, PCI_D0);
+
 		ret = pci_try_reset_function(vdev->pdev);
 		up_write(&vdev->memory_lock);
 
@@ -1566,11 +1593,8 @@
 	 *
 	 * If the VF token is provided but unused, an error is generated.
 	 */
-	if (!vdev->pdev->is_virtfn && !vdev->vf_token && !vf_token)
-		return 0; /* No VF token provided or required */
-
 	if (vdev->pdev->is_virtfn) {
-		struct vfio_pci_core_device *pf_vdev = get_pf_vdev(vdev);
+		struct vfio_pci_core_device *pf_vdev = vdev->sriov_pf_core_dev;
 		bool match;
 
 		if (!pf_vdev) {
@@ -1583,7 +1607,6 @@
 		}
 
 		if (!vf_token) {
-			vfio_device_put(&pf_vdev->vdev);
 			pci_info_ratelimited(vdev->pdev,
 				"VF token required to access device\n");
 			return -EACCES;
@@ -1593,8 +1616,6 @@
 		match = uuid_equal(uuid, &pf_vdev->vf_token->uuid);
 		mutex_unlock(&pf_vdev->vf_token->lock);
 
-		vfio_device_put(&pf_vdev->vdev);
-
 		if (!match) {
 			pci_info_ratelimited(vdev->pdev,
 				"Incorrect VF token provided for device\n");
@@ -1715,8 +1736,30 @@
 static int vfio_pci_vf_init(struct vfio_pci_core_device *vdev)
 {
 	struct pci_dev *pdev = vdev->pdev;
+	struct vfio_pci_core_device *cur;
+	struct pci_dev *physfn;
 	int ret;
 
+	if (pdev->is_virtfn) {
+		/*
+		 * If this VF was created by our vfio_pci_core_sriov_configure()
+		 * then we can find the PF vfio_pci_core_device now, and due to
+		 * the locking in pci_disable_sriov() it cannot change until
+		 * this VF device driver is removed.
+		 */
+		physfn = pci_physfn(vdev->pdev);
+		mutex_lock(&vfio_pci_sriov_pfs_mutex);
+		list_for_each_entry(cur, &vfio_pci_sriov_pfs, sriov_pfs_item) {
+			if (cur->pdev == physfn) {
+				vdev->sriov_pf_core_dev = cur;
+				break;
+			}
+		}
+		mutex_unlock(&vfio_pci_sriov_pfs_mutex);
+		return 0;
+	}
+
+	/* Not a SRIOV PF */
 	if (!pdev->is_physfn)
 		return 0;
 
@@ -1788,6 +1831,7 @@
 	INIT_LIST_HEAD(&vdev->ioeventfds_list);
 	mutex_init(&vdev->vma_lock);
 	INIT_LIST_HEAD(&vdev->vma_list);
+	INIT_LIST_HEAD(&vdev->sriov_pfs_item);
 	init_rwsem(&vdev->memory_lock);
 }
 EXPORT_SYMBOL_GPL(vfio_pci_core_init_device);
@@ -1886,7 +1930,7 @@
 {
 	struct pci_dev *pdev = vdev->pdev;
 
-	pci_disable_sriov(pdev);
+	vfio_pci_core_sriov_configure(pdev, 0);
 
 	vfio_unregister_group_dev(&vdev->vdev);
 
@@ -1926,21 +1970,49 @@
 
 int vfio_pci_core_sriov_configure(struct pci_dev *pdev, int nr_virtfn)
 {
+	struct vfio_pci_core_device *vdev;
 	struct vfio_device *device;
 	int ret = 0;
 
+	device_lock_assert(&pdev->dev);
+
 	device = vfio_device_get_from_dev(&pdev->dev);
 	if (!device)
 		return -ENODEV;
 
-	if (nr_virtfn == 0)
-		pci_disable_sriov(pdev);
-	else
+	vdev = container_of(device, struct vfio_pci_core_device, vdev);
+
+	if (nr_virtfn) {
+		mutex_lock(&vfio_pci_sriov_pfs_mutex);
+		/*
+		 * The thread that adds the vdev to the list is the only thread
+		 * that gets to call pci_enable_sriov() and we will only allow
+		 * it to be called once without going through
+		 * pci_disable_sriov()
+		 */
+		if (!list_empty(&vdev->sriov_pfs_item)) {
+			ret = -EINVAL;
+			goto out_unlock;
+		}
+		list_add_tail(&vdev->sriov_pfs_item, &vfio_pci_sriov_pfs);
+		mutex_unlock(&vfio_pci_sriov_pfs_mutex);
 		ret = pci_enable_sriov(pdev, nr_virtfn);
+		if (ret)
+			goto out_del;
+		ret = nr_virtfn;
+		goto out_put;
+	}
 
-	vfio_device_put(device);
+	pci_disable_sriov(pdev);
 
-	return ret < 0 ? ret : nr_virtfn;
+out_del:
+	mutex_lock(&vfio_pci_sriov_pfs_mutex);
+	list_del_init(&vdev->sriov_pfs_item);
+out_unlock:
+	mutex_unlock(&vfio_pci_sriov_pfs_mutex);
+out_put:
+	vfio_device_put(device);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(vfio_pci_core_sriov_configure);
 
@@ -2064,6 +2136,18 @@
 	}
 	cur_mem = NULL;
 
+	/*
+	 * The pci_reset_bus() will reset all the devices in the bus.
+	 * The power state can be non-D0 for some of the devices in the bus.
+	 * For these devices, the pci_reset_bus() will internally set
+	 * the power state to D0 without vfio driver involvement.
+	 * For the devices which have NoSoftRst-, the reset function can
+	 * cause the PCI config space reset without restoring the original
+	 * state (saved locally in 'vdev->pm_save').
+	 */
+	list_for_each_entry(cur, &dev_set->device_list, vdev.dev_set_list)
+		vfio_pci_set_power_state(cur, PCI_D0);
+
 	ret = pci_reset_bus(pdev);
 
 err_undo:
@@ -2117,6 +2201,18 @@
 	if (!pdev)
 		return false;
 
+	/*
+	 * The pci_reset_bus() will reset all the devices in the bus.
+	 * The power state can be non-D0 for some of the devices in the bus.
+	 * For these devices, the pci_reset_bus() will internally set
+	 * the power state to D0 without vfio driver involvement.
+	 * For the devices which have NoSoftRst-, the reset function can
+	 * cause the PCI config space reset without restoring the original
+	 * state (saved locally in 'vdev->pm_save').
+	 */
+	list_for_each_entry(cur, &dev_set->device_list, vdev.dev_set_list)
+		vfio_pci_set_power_state(cur, PCI_D0);
+
 	ret = pci_reset_bus(pdev);
 	if (ret)
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/vfio_pci_intrs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/vfio_pci_intrs.c
@@ -29,15 +29,22 @@
 {
 	struct vfio_pci_core_device *vdev = opaque;
 
-	if (likely(is_intx(vdev) && !vdev->virq_disabled))
-		eventfd_signal(vdev->ctx[0].trigger, 1);
+	if (likely(is_intx(vdev) && !vdev->virq_disabled)) {
+		struct eventfd_ctx *trigger;
+
+		trigger = READ_ONCE(vdev->ctx[0].trigger);
+		if (likely(trigger))
+			eventfd_signal(trigger, 1);
+	}
 }
 
-void vfio_pci_intx_mask(struct vfio_pci_core_device *vdev)
+static void __vfio_pci_intx_mask(struct vfio_pci_core_device *vdev)
 {
 	struct pci_dev *pdev = vdev->pdev;
 	unsigned long flags;
 
+	lockdep_assert_held(&vdev->igate);
+
 	spin_lock_irqsave(&vdev->irqlock, flags);
 
 	/*
@@ -65,6 +72,13 @@
 	spin_unlock_irqrestore(&vdev->irqlock, flags);
 }
 
+void vfio_pci_intx_mask(struct vfio_pci_core_device *vdev)
+{
+	mutex_lock(&vdev->igate);
+	__vfio_pci_intx_mask(vdev);
+	mutex_unlock(&vdev->igate);
+}
+
 /*
  * If this is triggered by an eventfd, we can't call eventfd_signal
  * or else we'll deadlock on the eventfd wait queue.  Return >0 when
@@ -107,12 +121,21 @@
 	return ret;
 }
 
-void vfio_pci_intx_unmask(struct vfio_pci_core_device *vdev)
+static void __vfio_pci_intx_unmask(struct vfio_pci_core_device *vdev)
 {
+	lockdep_assert_held(&vdev->igate);
+
 	if (vfio_pci_intx_unmask_handler(vdev, NULL) > 0)
 		vfio_send_intx_eventfd(vdev, NULL);
 }
 
+void vfio_pci_intx_unmask(struct vfio_pci_core_device *vdev)
+{
+	mutex_lock(&vdev->igate);
+	__vfio_pci_intx_unmask(vdev);
+	mutex_unlock(&vdev->igate);
+}
+
 static irqreturn_t vfio_intx_handler(int irq, void *dev_id)
 {
 	struct vfio_pci_core_device *vdev = dev_id;
@@ -139,95 +162,106 @@
 	return ret;
 }
 
-static int vfio_intx_enable(struct vfio_pci_core_device *vdev)
+static int vfio_intx_enable(struct vfio_pci_core_device *vdev,
+			    struct eventfd_ctx *trigger)
 {
+	struct pci_dev *pdev = vdev->pdev;
+	unsigned long irqflags;
+	char *name;
+	int ret;
+
 	if (!is_irq_none(vdev))
 		return -EINVAL;
 
-	if (!vdev->pdev->irq)
+	if (!pdev->irq)
 		return -ENODEV;
 
+	name = kasprintf(GFP_KERNEL, "vfio-intx(%s)", pci_name(pdev));
+	if (!name)
+		return -ENOMEM;
+
 	vdev->ctx = kzalloc(sizeof(struct vfio_pci_irq_ctx), GFP_KERNEL);
-	if (!vdev->ctx)
+	if (!vdev->ctx) {
+		kfree(name);
 		return -ENOMEM;
+	}
 
 	vdev->num_ctx = 1;
 
+	vdev->ctx[0].name = name;
+	vdev->ctx[0].trigger = trigger;
+
 	/*
-	 * If the virtual interrupt is masked, restore it.  Devices
-	 * supporting DisINTx can be masked at the hardware level
-	 * here, non-PCI-2.3 devices will have to wait until the
-	 * interrupt is enabled.
+	 * Fill the initial masked state based on virq_disabled.  After
+	 * enable, changing the DisINTx bit in vconfig directly changes INTx
+	 * masking.  igate prevents races during setup, once running masked
+	 * is protected via irqlock.
+	 *
+	 * Devices supporting DisINTx also reflect the current mask state in
+	 * the physical DisINTx bit, which is not affected during IRQ setup.
+	 *
+	 * Devices without DisINTx support require an exclusive interrupt.
+	 * IRQ masking is performed at the IRQ chip.  Again, igate protects
+	 * against races during setup and IRQ handlers and irqfds are not
+	 * yet active, therefore masked is stable and can be used to
+	 * conditionally auto-enable the IRQ.
+	 *
+	 * irq_type must be stable while the IRQ handler is registered,
+	 * therefore it must be set before request_irq().
 	 */
 	vdev->ctx[0].masked = vdev->virq_disabled;
-	if (vdev->pci_2_3)
-		pci_intx(vdev->pdev, !vdev->ctx[0].masked);
+	if (vdev->pci_2_3) {
+		pci_intx(pdev, !vdev->ctx[0].masked);
+		irqflags = IRQF_SHARED;
+	} else {
+		irqflags = vdev->ctx[0].masked ? IRQF_NO_AUTOEN : 0;
+	}
 
 	vdev->irq_type = VFIO_PCI_INTX_IRQ_INDEX;
 
+	ret = request_irq(pdev->irq, vfio_intx_handler,
+			  irqflags, vdev->ctx[0].name, vdev);
+	if (ret) {
+		vdev->irq_type = VFIO_PCI_NUM_IRQS;
+		kfree(name);
+		vdev->num_ctx = 0;
+		kfree(vdev->ctx);
+		return ret;
+	}
+
 	return 0;
 }
 
-static int vfio_intx_set_signal(struct vfio_pci_core_device *vdev, int fd)
+static int vfio_intx_set_signal(struct vfio_pci_core_device *vdev,
+				struct eventfd_ctx *trigger)
 {
 	struct pci_dev *pdev = vdev->pdev;
-	unsigned long irqflags = IRQF_SHARED;
-	struct eventfd_ctx *trigger;
-	unsigned long flags;
-	int ret;
-
-	if (vdev->ctx[0].trigger) {
-		free_irq(pdev->irq, vdev);
-		kfree(vdev->ctx[0].name);
-		eventfd_ctx_put(vdev->ctx[0].trigger);
-		vdev->ctx[0].trigger = NULL;
-	}
+	struct eventfd_ctx *old;
 
-	if (fd < 0) /* Disable only */
-		return 0;
+	old = vdev->ctx[0].trigger;
 
-	vdev->ctx[0].name = kasprintf(GFP_KERNEL, "vfio-intx(%s)",
-				      pci_name(pdev));
-	if (!vdev->ctx[0].name)
-		return -ENOMEM;
+	WRITE_ONCE(vdev->ctx[0].trigger, trigger);
 
-	trigger = eventfd_ctx_fdget(fd);
-	if (IS_ERR(trigger)) {
-		kfree(vdev->ctx[0].name);
-		return PTR_ERR(trigger);
+	/* Releasing an old ctx requires synchronizing in-flight users */
+	if (old) {
+		synchronize_irq(pdev->irq);
+		vfio_virqfd_flush_thread(&vdev->ctx[0].unmask);
+		eventfd_ctx_put(old);
 	}
 
-	vdev->ctx[0].trigger = trigger;
-
-	if (!vdev->pci_2_3)
-		irqflags = 0;
-
-	ret = request_irq(pdev->irq, vfio_intx_handler,
-			  irqflags, vdev->ctx[0].name, vdev);
-	if (ret) {
-		vdev->ctx[0].trigger = NULL;
-		kfree(vdev->ctx[0].name);
-		eventfd_ctx_put(trigger);
-		return ret;
-	}
-
-	/*
-	 * INTx disable will stick across the new irq setup,
-	 * disable_irq won't.
-	 */
-	spin_lock_irqsave(&vdev->irqlock, flags);
-	if (!vdev->pci_2_3 && vdev->ctx[0].masked)
-		disable_irq_nosync(pdev->irq);
-	spin_unlock_irqrestore(&vdev->irqlock, flags);
-
 	return 0;
 }
 
 static void vfio_intx_disable(struct vfio_pci_core_device *vdev)
 {
+	struct pci_dev *pdev = vdev->pdev;
+
 	vfio_virqfd_disable(&vdev->ctx[0].unmask);
 	vfio_virqfd_disable(&vdev->ctx[0].mask);
-	vfio_intx_set_signal(vdev, -1);
+	free_irq(pdev->irq, vdev);
+	if (vdev->ctx[0].trigger)
+		eventfd_ctx_put(vdev->ctx[0].trigger);
+	kfree(vdev->ctx[0].name);
 	vdev->irq_type = VFIO_PCI_NUM_IRQS;
 	vdev->num_ctx = 0;
 	kfree(vdev->ctx);
@@ -425,11 +459,11 @@
 		return -EINVAL;
 
 	if (flags & VFIO_IRQ_SET_DATA_NONE) {
-		vfio_pci_intx_unmask(vdev);
+		__vfio_pci_intx_unmask(vdev);
 	} else if (flags & VFIO_IRQ_SET_DATA_BOOL) {
 		uint8_t unmask = *(uint8_t *)data;
 		if (unmask)
-			vfio_pci_intx_unmask(vdev);
+			__vfio_pci_intx_unmask(vdev);
 	} else if (flags & VFIO_IRQ_SET_DATA_EVENTFD) {
 		int32_t fd = *(int32_t *)data;
 		if (fd >= 0)
@@ -452,11 +486,11 @@
 		return -EINVAL;
 
 	if (flags & VFIO_IRQ_SET_DATA_NONE) {
-		vfio_pci_intx_mask(vdev);
+		__vfio_pci_intx_mask(vdev);
 	} else if (flags & VFIO_IRQ_SET_DATA_BOOL) {
 		uint8_t mask = *(uint8_t *)data;
 		if (mask)
-			vfio_pci_intx_mask(vdev);
+			__vfio_pci_intx_mask(vdev);
 	} else if (flags & VFIO_IRQ_SET_DATA_EVENTFD) {
 		return -ENOTTY; /* XXX implement me */
 	}
@@ -477,19 +511,23 @@
 		return -EINVAL;
 
 	if (flags & VFIO_IRQ_SET_DATA_EVENTFD) {
+		struct eventfd_ctx *trigger = NULL;
 		int32_t fd = *(int32_t *)data;
 		int ret;
 
+		if (fd >= 0) {
+			trigger = eventfd_ctx_fdget(fd);
+			if (IS_ERR(trigger))
+				return PTR_ERR(trigger);
+		}
+
 		if (is_intx(vdev))
-			return vfio_intx_set_signal(vdev, fd);
+			ret = vfio_intx_set_signal(vdev, trigger);
+		else
+			ret = vfio_intx_enable(vdev, trigger);
 
-		ret = vfio_intx_enable(vdev);
-		if (ret)
-			return ret;
-
-		ret = vfio_intx_set_signal(vdev, fd);
-		if (ret)
-			vfio_intx_disable(vdev);
+		if (ret && trigger)
+			eventfd_ctx_put(trigger);
 
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/vfio_pci_rdwr.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/vfio_pci_rdwr.c
@@ -16,6 +16,7 @@
 #include <linux/io.h>
 #include <linux/vfio.h>
 #include <linux/vgaarb.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
 
 #include <linux/vfio_pci_core.h>
 
@@ -288,6 +289,7 @@
 	return done;
 }
 
+#ifdef CONFIG_VFIO_PCI_VGA
 ssize_t vfio_pci_vga_rw(struct vfio_pci_core_device *vdev, char __user *buf,
 			       size_t count, loff_t *ppos, bool iswrite)
 {
@@ -355,6 +357,7 @@
 
 	return done;
 }
+#endif
 
 static void vfio_pci_ioeventfd_do_write(struct vfio_pci_ioeventfd *ioeventfd,
 					bool test_mem)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/pci/vfio_pci_zdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/pci/vfio_pci_zdev.c
@@ -11,6 +11,7 @@
 #include <linux/uaccess.h>
 #include <linux/vfio.h>
 #include <linux/vfio_zdev.h>
+#include <linux/kvm_host.h>
 #include <asm/pci_clp.h>
 #include <asm/pci_io.h>
 
@@ -23,14 +24,15 @@
 {
 	struct vfio_device_info_cap_zpci_base cap = {
 		.header.id = VFIO_DEVICE_INFO_CAP_ZPCI_BASE,
-		.header.version = 1,
+		.header.version = 2,
 		.start_dma = zdev->start_dma,
 		.end_dma = zdev->end_dma,
 		.pchid = zdev->pchid,
 		.vfn = zdev->vfn,
 		.fmb_length = zdev->fmb_length,
 		.pft = zdev->pft,
-		.gid = zdev->pfgid
+		.gid = zdev->pfgid,
+		.fh = zdev->fh
 	};
 
 	return vfio_info_add_capability(caps, &cap.header, sizeof(cap));
@@ -43,14 +45,16 @@
 {
 	struct vfio_device_info_cap_zpci_group cap = {
 		.header.id = VFIO_DEVICE_INFO_CAP_ZPCI_GROUP,
-		.header.version = 1,
+		.header.version = 2,
 		.dasm = zdev->dma_mask,
 		.msi_addr = zdev->msi_addr,
 		.flags = VFIO_DEVICE_INFO_ZPCI_FLAG_REFRESH,
 		.mui = zdev->fmb_update,
 		.noi = zdev->max_msi,
 		.maxstbl = ZPCI_MAX_WRITE_SIZE,
-		.version = zdev->version
+		.version = zdev->version,
+		.reserved = 0,
+		.imaxstbl = zdev->maxstbl
 	};
 
 	return vfio_info_add_capability(caps, &cap.header, sizeof(cap));
@@ -136,3 +140,63 @@
 
 	return ret;
 }
+
+static int vfio_pci_zdev_group_notifier(struct notifier_block *nb,
+					unsigned long action, void *data)
+{
+	struct zpci_dev *zdev = container_of(nb, struct zpci_dev,
+					     kvm_group_nb);
+
+	if (action == VFIO_GROUP_NOTIFY_SET_KVM && zpci_kvm_hook.kvm_register) {
+		if (data) {
+			if (zpci_kvm_hook.kvm_register(zdev, data))
+				return NOTIFY_BAD;
+		}
+	}
+
+	return NOTIFY_OK;
+}
+
+int vfio_pci_zdev_open_device(struct vfio_pci_core_device *vdev)
+{
+	struct zpci_dev *zdev = to_zpci(vdev->pdev);
+	unsigned long events = VFIO_GROUP_NOTIFY_SET_KVM;
+	int ret;
+
+	if (!zdev)
+		return -ENODEV;
+
+	/*
+	 * Jammy-specific: backporting upstream commit 421cfe6596f6cb would
+	 * require a large number of pre-req series to also be applied,
+	 * affecting vfio across all platforms.
+	 * Instead implement a vfio KVM group notifier here which only
+	 * affects vfio-pci-zdev.  Rather than relying on the kvm pointer
+	 * being provided in the vdev, get it from the notifier.  Sice we know
+	 * the kvm will already be set, we can then immediately unregister the
+	 * notifier.
+	 */
+	zdev->kvm_group_nb.notifier_call = vfio_pci_zdev_group_notifier;
+	ret = vfio_register_notifier(&vdev->pdev->dev, VFIO_GROUP_NOTIFY,
+				     &events, &zdev->kvm_group_nb);
+	if (ret != 0) {
+		pr_warn("vfio_register_notifier for group failed: %d\n", ret);
+		return ret;
+	}
+
+	vfio_unregister_notifier(&vdev->pdev->dev, VFIO_GROUP_NOTIFY,
+				 &zdev->kvm_group_nb);
+
+	return 0;
+}
+
+void vfio_pci_zdev_close_device(struct vfio_pci_core_device *vdev)
+{
+	struct zpci_dev *zdev = to_zpci(vdev->pdev);
+
+	if (!zdev || !zdev->kzdev)
+		return;
+
+	if (zpci_kvm_hook.kvm_unregister)
+		zpci_kvm_hook.kvm_unregister(zdev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/platform/vfio_platform_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/platform/vfio_platform_common.c
@@ -72,12 +72,11 @@
 				  const char **extra_dbg)
 {
 #ifdef CONFIG_ACPI
-	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
 	struct device *dev = vdev->device;
 	acpi_handle handle = ACPI_HANDLE(dev);
 	acpi_status acpi_ret;
 
-	acpi_ret = acpi_evaluate_object(handle, "_RST", NULL, &buffer);
+	acpi_ret = acpi_evaluate_object(handle, "_RST", NULL, NULL);
 	if (ACPI_FAILURE(acpi_ret)) {
 		if (extra_dbg)
 			*extra_dbg = acpi_format_exception(acpi_ret);
@@ -389,6 +388,16 @@
 {
 	unsigned int done = 0;
 
+	if (off >= reg->size)
+		return -EINVAL;
+
+	count = min_t(size_t, count, reg->size - off);
+
+	if (off >= reg->size)
+		return -EINVAL;
+
+	count = min_t(size_t, count, reg->size - off);
+
 	if (!reg->ioaddr) {
 		reg->ioaddr =
 			ioremap(reg->addr, reg->size);
@@ -467,6 +476,16 @@
 {
 	unsigned int done = 0;
 
+	if (off >= reg->size)
+		return -EINVAL;
+
+	count = min_t(size_t, count, reg->size - off);
+
+	if (off >= reg->size)
+		return -EINVAL;
+
+	count = min_t(size_t, count, reg->size - off);
+
 	if (!reg->ioaddr) {
 		reg->ioaddr =
 			ioremap(reg->addr, reg->size);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/platform/vfio_platform_irq.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/platform/vfio_platform_irq.c
@@ -136,6 +136,16 @@
 	return 0;
 }
 
+/*
+ * The trigger eventfd is guaranteed valid in the interrupt path
+ * and protected by the igate mutex when triggered via ioctl.
+ */
+static void vfio_send_eventfd(struct vfio_platform_irq *irq_ctx)
+{
+	if (likely(irq_ctx->trigger))
+		eventfd_signal(irq_ctx->trigger, 1);
+}
+
 static irqreturn_t vfio_automasked_irq_handler(int irq, void *dev_id)
 {
 	struct vfio_platform_irq *irq_ctx = dev_id;
@@ -155,7 +165,7 @@
 	spin_unlock_irqrestore(&irq_ctx->lock, flags);
 
 	if (ret == IRQ_HANDLED)
-		eventfd_signal(irq_ctx->trigger, 1);
+		vfio_send_eventfd(irq_ctx);
 
 	return ret;
 }
@@ -164,22 +174,19 @@
 {
 	struct vfio_platform_irq *irq_ctx = dev_id;
 
-	eventfd_signal(irq_ctx->trigger, 1);
+	vfio_send_eventfd(irq_ctx);
 
 	return IRQ_HANDLED;
 }
 
 static int vfio_set_trigger(struct vfio_platform_device *vdev, int index,
-			    int fd, irq_handler_t handler)
+			    int fd)
 {
 	struct vfio_platform_irq *irq = &vdev->irqs[index];
 	struct eventfd_ctx *trigger;
-	int ret;
 
 	if (irq->trigger) {
-		irq_clear_status_flags(irq->hwirq, IRQ_NOAUTOEN);
-		free_irq(irq->hwirq, irq);
-		kfree(irq->name);
+		disable_irq(irq->hwirq);
 		eventfd_ctx_put(irq->trigger);
 		irq->trigger = NULL;
 	}
@@ -187,30 +194,20 @@
 	if (fd < 0) /* Disable only */
 		return 0;
 
-	irq->name = kasprintf(GFP_KERNEL, "vfio-irq[%d](%s)",
-						irq->hwirq, vdev->name);
-	if (!irq->name)
-		return -ENOMEM;
-
 	trigger = eventfd_ctx_fdget(fd);
-	if (IS_ERR(trigger)) {
-		kfree(irq->name);
+	if (IS_ERR(trigger))
 		return PTR_ERR(trigger);
-	}
 
 	irq->trigger = trigger;
 
-	irq_set_status_flags(irq->hwirq, IRQ_NOAUTOEN);
-	ret = request_irq(irq->hwirq, handler, 0, irq->name, irq);
-	if (ret) {
-		kfree(irq->name);
-		eventfd_ctx_put(trigger);
-		irq->trigger = NULL;
-		return ret;
-	}
-
-	if (!irq->masked)
-		enable_irq(irq->hwirq);
+	/*
+	 * irq->masked effectively provides nested disables within the overall
+	 * enable relative to trigger.  Specifically request_irq() is called
+	 * with NO_AUTOEN, therefore the IRQ is initially disabled.  The user
+	 * may only further disable the IRQ with a MASK operations because
+	 * irq->masked is initially false.
+	 */
+	enable_irq(irq->hwirq);
 
 	return 0;
 }
@@ -229,7 +226,7 @@
 		handler = vfio_irq_handler;
 
 	if (!count && (flags & VFIO_IRQ_SET_DATA_NONE))
-		return vfio_set_trigger(vdev, index, -1, handler);
+		return vfio_set_trigger(vdev, index, -1);
 
 	if (start != 0 || count != 1)
 		return -EINVAL;
@@ -237,7 +234,7 @@
 	if (flags & VFIO_IRQ_SET_DATA_EVENTFD) {
 		int32_t fd = *(int32_t *)data;
 
-		return vfio_set_trigger(vdev, index, fd, handler);
+		return vfio_set_trigger(vdev, index, fd);
 	}
 
 	if (flags & VFIO_IRQ_SET_DATA_NONE) {
@@ -261,6 +258,14 @@
 		    unsigned start, unsigned count, uint32_t flags,
 		    void *data) = NULL;
 
+	/*
+	 * For compatibility, errors from request_irq() are local to the
+	 * SET_IRQS path and reflected in the name pointer.  This allows,
+	 * for example, polling mode fallback for an exclusive IRQ failure.
+	 */
+	if (IS_ERR(vdev->irqs[index].name))
+		return PTR_ERR(vdev->irqs[index].name);
+
 	switch (flags & VFIO_IRQ_SET_ACTION_TYPE_MASK) {
 	case VFIO_IRQ_SET_ACTION_MASK:
 		func = vfio_platform_set_irq_mask;
@@ -281,7 +286,7 @@
 
 int vfio_platform_irq_init(struct vfio_platform_device *vdev)
 {
-	int cnt = 0, i;
+	int cnt = 0, i, ret = 0;
 
 	while (vdev->get_irq(vdev, cnt) >= 0)
 		cnt++;
@@ -292,37 +297,70 @@
 
 	for (i = 0; i < cnt; i++) {
 		int hwirq = vdev->get_irq(vdev, i);
+		irq_handler_t handler = vfio_irq_handler;
 
-		if (hwirq < 0)
+		if (hwirq < 0) {
+			ret = -EINVAL;
 			goto err;
+		}
 
 		spin_lock_init(&vdev->irqs[i].lock);
 
 		vdev->irqs[i].flags = VFIO_IRQ_INFO_EVENTFD;
 
-		if (irq_get_trigger_type(hwirq) & IRQ_TYPE_LEVEL_MASK)
+		if (irq_get_trigger_type(hwirq) & IRQ_TYPE_LEVEL_MASK) {
 			vdev->irqs[i].flags |= VFIO_IRQ_INFO_MASKABLE
 						| VFIO_IRQ_INFO_AUTOMASKED;
+			handler = vfio_automasked_irq_handler;
+		}
 
 		vdev->irqs[i].count = 1;
 		vdev->irqs[i].hwirq = hwirq;
 		vdev->irqs[i].masked = false;
+		vdev->irqs[i].name = kasprintf(GFP_KERNEL,
+					       "vfio-irq[%d](%s)", hwirq,
+					       vdev->name);
+		if (!vdev->irqs[i].name) {
+			ret = -ENOMEM;
+			goto err;
+		}
+
+		ret = request_irq(hwirq, handler, IRQF_NO_AUTOEN,
+				  vdev->irqs[i].name, &vdev->irqs[i]);
+		if (ret) {
+			kfree(vdev->irqs[i].name);
+			vdev->irqs[i].name = ERR_PTR(ret);
+		}
 	}
 
 	vdev->num_irqs = cnt;
 
 	return 0;
 err:
+	for (--i; i >= 0; i--) {
+		if (!IS_ERR(vdev->irqs[i].name)) {
+			free_irq(vdev->irqs[i].hwirq, &vdev->irqs[i]);
+			kfree(vdev->irqs[i].name);
+		}
+	}
 	kfree(vdev->irqs);
-	return -EINVAL;
+	return ret;
 }
 
 void vfio_platform_irq_cleanup(struct vfio_platform_device *vdev)
 {
 	int i;
 
-	for (i = 0; i < vdev->num_irqs; i++)
-		vfio_set_trigger(vdev, i, -1, NULL);
+	for (i = 0; i < vdev->num_irqs; i++) {
+		vfio_virqfd_disable(&vdev->irqs[i].mask);
+		vfio_virqfd_disable(&vdev->irqs[i].unmask);
+		if (!IS_ERR(vdev->irqs[i].name)) {
+			free_irq(vdev->irqs[i].hwirq, &vdev->irqs[i]);
+			if (vdev->irqs[i].trigger)
+				eventfd_ctx_put(vdev->irqs[i].trigger);
+			kfree(vdev->irqs[i].name);
+		}
+	}
 
 	vdev->num_irqs = 0;
 	kfree(vdev->irqs);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/vfio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/vfio.c
@@ -1850,6 +1850,7 @@
 	buf = krealloc(caps->buf, caps->size + size, GFP_KERNEL);
 	if (!buf) {
 		kfree(caps->buf);
+		caps->buf = NULL;
 		caps->size = 0;
 		return ERR_PTR(-ENOMEM);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/vfio_iommu_type1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/vfio_iommu_type1.c
@@ -100,6 +100,8 @@
 	struct task_struct	*task;
 	struct rb_root		pfn_list;	/* Ex-user pinned pfn list */
 	unsigned long		*bitmap;
+	struct mm_struct	*mm;
+	size_t			locked_vm;
 };
 
 struct vfio_batch {
@@ -416,6 +418,19 @@
 	return ret;
 }
 
+static int mm_lock_acct(struct task_struct *task, struct mm_struct *mm,
+			bool lock_cap, long npage)
+{
+	int ret = mmap_write_lock_killable(mm);
+
+	if (ret)
+		return ret;
+
+	ret = __account_locked_vm(mm, abs(npage), npage > 0, task, lock_cap);
+	mmap_write_unlock(mm);
+	return ret;
+}
+
 static int vfio_lock_acct(struct vfio_dma *dma, long npage, bool async)
 {
 	struct mm_struct *mm;
@@ -424,16 +439,13 @@
 	if (!npage)
 		return 0;
 
-	mm = async ? get_task_mm(dma->task) : dma->task->mm;
-	if (!mm)
+	mm = dma->mm;
+	if (async && !mmget_not_zero(mm))
 		return -ESRCH; /* process exited */
 
-	ret = mmap_write_lock_killable(mm);
-	if (!ret) {
-		ret = __account_locked_vm(mm, abs(npage), npage > 0, dma->task,
-					  dma->lock_cap);
-		mmap_write_unlock(mm);
-	}
+	ret = mm_lock_acct(dma->task, mm, dma->lock_cap, npage);
+	if (!ret)
+		dma->locked_vm += npage;
 
 	if (async)
 		mmput(mm);
@@ -561,6 +573,18 @@
 	ret = pin_user_pages_remote(mm, vaddr, npages, flags | FOLL_LONGTERM,
 				    pages, NULL, NULL);
 	if (ret > 0) {
+		int i;
+
+		/*
+		 * The zero page is always resident, we don't need to pin it
+		 * and it falls into our invalid/reserved test so we don't
+		 * unpin in put_pfn().  Unpin all zero pages in the batch here.
+		 */
+		for (i = 0 ; i < ret; i++) {
+			if (unlikely(is_zero_pfn(page_to_pfn(pages[i]))))
+				unpin_user_page(pages[i]);
+		}
+
 		*pfn = page_to_pfn(pages[0]);
 		goto done;
 	}
@@ -786,8 +810,8 @@
 	struct mm_struct *mm;
 	int ret;
 
-	mm = get_task_mm(dma->task);
-	if (!mm)
+	mm = dma->mm;
+	if (!mmget_not_zero(mm))
 		return -ENODEV;
 
 	ret = vaddr_get_pfns(mm, vaddr, 1, dma->prot, pfn_base, pages);
@@ -797,7 +821,7 @@
 	ret = 0;
 
 	if (do_accounting && !is_invalid_reserved_pfn(*pfn_base)) {
-		ret = vfio_lock_acct(dma, 1, true);
+		ret = vfio_lock_acct(dma, 1, false);
 		if (ret) {
 			put_pfn(*pfn_base, dma->prot);
 			if (ret == -ENOMEM)
@@ -1167,6 +1191,7 @@
 	vfio_unmap_unpin(iommu, dma, true);
 	vfio_unlink_dma(iommu, dma);
 	put_task_struct(dma->task);
+	mmdrop(dma->mm);
 	vfio_dma_bitmap_free(dma);
 	if (dma->vaddr_invalid) {
 		iommu->vaddr_invalid_count--;
@@ -1551,6 +1576,38 @@
 	return list_empty(iova);
 }
 
+static int vfio_change_dma_owner(struct vfio_dma *dma)
+{
+	struct task_struct *task = current->group_leader;
+	struct mm_struct *mm = current->mm;
+	long npage = dma->locked_vm;
+	bool lock_cap;
+	int ret;
+
+	if (mm == dma->mm)
+		return 0;
+
+	lock_cap = capable(CAP_IPC_LOCK);
+	ret = mm_lock_acct(task, mm, lock_cap, npage);
+	if (ret)
+		return ret;
+
+	if (mmget_not_zero(dma->mm)) {
+		mm_lock_acct(dma->task, dma->mm, dma->lock_cap, -npage);
+		mmput(dma->mm);
+	}
+
+	if (dma->task != task) {
+		put_task_struct(dma->task);
+		dma->task = get_task_struct(task);
+	}
+	mmdrop(dma->mm);
+	dma->mm = mm;
+	mmgrab(dma->mm);
+	dma->lock_cap = lock_cap;
+	return 0;
+}
+
 static int vfio_dma_do_map(struct vfio_iommu *iommu,
 			   struct vfio_iommu_type1_dma_map *map)
 {
@@ -1600,6 +1657,9 @@
 			   dma->size != size) {
 			ret = -EINVAL;
 		} else {
+			ret = vfio_change_dma_owner(dma);
+			if (ret)
+				goto out_unlock;
 			dma->vaddr = vaddr;
 			dma->vaddr_invalid = false;
 			iommu->vaddr_invalid_count--;
@@ -1637,29 +1697,15 @@
 	 * against the locked memory limit and we need to be able to do both
 	 * outside of this call path as pinning can be asynchronous via the
 	 * external interfaces for mdev devices.  RLIMIT_MEMLOCK requires a
-	 * task_struct and VM locked pages requires an mm_struct, however
-	 * holding an indefinite mm reference is not recommended, therefore we
-	 * only hold a reference to a task.  We could hold a reference to
-	 * current, however QEMU uses this call path through vCPU threads,
-	 * which can be killed resulting in a NULL mm and failure in the unmap
-	 * path when called via a different thread.  Avoid this problem by
-	 * using the group_leader as threads within the same group require
-	 * both CLONE_THREAD and CLONE_VM and will therefore use the same
-	 * mm_struct.
-	 *
-	 * Previously we also used the task for testing CAP_IPC_LOCK at the
-	 * time of pinning and accounting, however has_capability() makes use
-	 * of real_cred, a copy-on-write field, so we can't guarantee that it
-	 * matches group_leader, or in fact that it might not change by the
-	 * time it's evaluated.  If a process were to call MAP_DMA with
-	 * CAP_IPC_LOCK but later drop it, it doesn't make sense that they
-	 * possibly see different results for an iommu_mapped vfio_dma vs
-	 * externally mapped.  Therefore track CAP_IPC_LOCK in vfio_dma at the
-	 * time of calling MAP_DMA.
+	 * task_struct. Save the group_leader so that all DMA tracking uses
+	 * the same task, to make debugging easier.  VM locked pages requires
+	 * an mm_struct, so grab the mm in case the task dies.
 	 */
 	get_task_struct(current->group_leader);
 	dma->task = current->group_leader;
 	dma->lock_cap = capable(CAP_IPC_LOCK);
+	dma->mm = current->mm;
+	mmgrab(dma->mm);
 
 	dma->pfn_list = RB_ROOT;
 
@@ -2820,7 +2866,7 @@
 static int vfio_iommu_migration_build_caps(struct vfio_iommu *iommu,
 					   struct vfio_info_cap *caps)
 {
-	struct vfio_iommu_type1_info_cap_migration cap_mig;
+	struct vfio_iommu_type1_info_cap_migration cap_mig = {};
 
 	cap_mig.header.id = VFIO_IOMMU_TYPE1_INFO_CAP_MIGRATION;
 	cap_mig.header.version = 1;
@@ -3156,9 +3202,8 @@
 			!(dma->prot & IOMMU_READ))
 		return -EPERM;
 
-	mm = get_task_mm(dma->task);
-
-	if (!mm)
+	mm = dma->mm;
+	if (!mmget_not_zero(mm))
 		return -EPERM;
 
 	if (kthread)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vfio/virqfd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vfio/virqfd.c
@@ -104,6 +104,13 @@
 		virqfd->thread(virqfd->opaque, virqfd->data);
 }
 
+static void virqfd_flush_inject(struct work_struct *work)
+{
+	struct virqfd *virqfd = container_of(work, struct virqfd, flush_inject);
+
+	flush_work(&virqfd->inject);
+}
+
 int vfio_virqfd_enable(void *opaque,
 		       int (*handler)(void *, void *),
 		       void (*thread)(void *, void *),
@@ -127,6 +134,7 @@
 
 	INIT_WORK(&virqfd->shutdown, virqfd_shutdown);
 	INIT_WORK(&virqfd->inject, virqfd_inject);
+	INIT_WORK(&virqfd->flush_inject, virqfd_flush_inject);
 
 	irqfd = fdget(fd);
 	if (!irqfd.file) {
@@ -217,6 +225,19 @@
 }
 EXPORT_SYMBOL_GPL(vfio_virqfd_disable);
 
+void vfio_virqfd_flush_thread(struct virqfd **pvirqfd)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&virqfd_lock, flags);
+	if (*pvirqfd && (*pvirqfd)->thread)
+		queue_work(vfio_irqfd_cleanup_wq, &(*pvirqfd)->flush_inject);
+	spin_unlock_irqrestore(&virqfd_lock, flags);
+
+	flush_workqueue(vfio_irqfd_cleanup_wq);
+}
+EXPORT_SYMBOL_GPL(vfio_virqfd_flush_thread);
+
 module_init(vfio_virqfd_init);
 module_exit(vfio_virqfd_exit);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/iotlb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/iotlb.c
@@ -57,6 +57,21 @@
 	if (last < start)
 		return -EFAULT;
 
+	/* If the range being mapped is [0, ULONG_MAX], split it into two entries
+	 * otherwise its size would overflow u64.
+	 */
+	if (start == 0 && last == ULONG_MAX) {
+		u64 mid = last / 2;
+		int err = vhost_iotlb_add_range_ctx(iotlb, start, mid, addr,
+				perm, opaque);
+
+		if (err)
+			return err;
+
+		addr += mid + 1;
+		start = mid + 1;
+	}
+
 	if (iotlb->limit &&
 	    iotlb->nmaps == iotlb->limit &&
 	    iotlb->flags & VHOST_IOTLB_FLAG_RETIRE) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/net.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/net.c
@@ -473,6 +473,7 @@
 		goto signal_used;
 
 	msghdr->msg_control = &ctl;
+	msghdr->msg_controllen = sizeof(ctl);
 	err = sock->ops->sendmsg(sock, msghdr, 0);
 	if (unlikely(err < 0)) {
 		vq_err(&nvq->vq, "Fail to batch sending packets\n");
@@ -932,13 +933,18 @@
 
 		err = sock->ops->sendmsg(sock, &msg, len);
 		if (unlikely(err < 0)) {
+			bool retry = err == -EAGAIN || err == -ENOMEM || err == -ENOBUFS;
+
 			if (zcopy_used) {
 				if (vq->heads[ubuf->desc].len == VHOST_DMA_IN_PROGRESS)
 					vhost_net_ubuf_put(ubufs);
-				nvq->upend_idx = ((unsigned)nvq->upend_idx - 1)
-					% UIO_MAXIOV;
+				if (retry)
+					nvq->upend_idx = ((unsigned)nvq->upend_idx - 1)
+						% UIO_MAXIOV;
+				else
+					vq->heads[ubuf->desc].len = VHOST_DMA_DONE_LEN;
 			}
-			if (err == -EAGAIN || err == -ENOMEM || err == -ENOBUFS) {
+			if (retry) {
 				vhost_discard_vq_desc(vq, 1);
 				vhost_net_enable_vq(net, vq);
 				break;
@@ -1449,13 +1455,9 @@
 	return ERR_PTR(r);
 }
 
-static struct ptr_ring *get_tap_ptr_ring(int fd)
+static struct ptr_ring *get_tap_ptr_ring(struct file *file)
 {
 	struct ptr_ring *ring;
-	struct file *file = fget(fd);
-
-	if (!file)
-		return NULL;
 	ring = tun_get_tx_ring(file);
 	if (!IS_ERR(ring))
 		goto out;
@@ -1464,7 +1466,6 @@
 		goto out;
 	ring = NULL;
 out:
-	fput(file);
 	return ring;
 }
 
@@ -1521,6 +1522,9 @@
 	nvq = &n->vqs[index];
 	mutex_lock(&vq->mutex);
 
+	if (fd == -1)
+		vhost_clear_msg(&n->dev);
+
 	/* Verify that ring has been setup correctly. */
 	if (!vhost_vq_access_ok(vq)) {
 		r = -EFAULT;
@@ -1551,8 +1555,12 @@
 		r = vhost_net_enable_vq(n, vq);
 		if (r)
 			goto err_used;
-		if (index == VHOST_NET_VQ_RX)
-			nvq->rx_ring = get_tap_ptr_ring(fd);
+		if (index == VHOST_NET_VQ_RX) {
+			if (sock)
+				nvq->rx_ring = get_tap_ptr_ring(sock->file);
+			else
+				nvq->rx_ring = NULL;
+		}
 
 		oldubufs = nvq->ubufs;
 		nvq->ubufs = ubufs;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/scsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/scsi.c
@@ -899,20 +899,23 @@
 		/* virtio-scsi spec requires byte 0 of the lun to be 1 */
 		vq_err(vq, "Illegal virtio-scsi lun: %u\n", *vc->lunp);
 	} else {
-		struct vhost_scsi_tpg **vs_tpg, *tpg;
+		struct vhost_scsi_tpg **vs_tpg, *tpg = NULL;
 
-		vs_tpg = vhost_vq_get_backend(vq);	/* validated at handler entry */
-
-		tpg = READ_ONCE(vs_tpg[*vc->target]);
-		if (unlikely(!tpg)) {
-			vq_err(vq, "Target 0x%x does not exist\n", *vc->target);
-		} else {
-			if (tpgp)
-				*tpgp = tpg;
-			ret = 0;
+		if (vc->target) {
+			/* validated at handler entry */
+			vs_tpg = vhost_vq_get_backend(vq);
+			tpg = READ_ONCE(vs_tpg[*vc->target]);
+			if (unlikely(!tpg)) {
+				vq_err(vq, "Target 0x%x does not exist\n", *vc->target);
+				goto out;
+			}
 		}
-	}
 
+		if (tpgp)
+			*tpgp = tpg;
+		ret = 0;
+	}
+out:
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/vdpa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/vdpa.c
@@ -97,11 +97,12 @@
 		return;
 
 	irq = ops->get_vq_irq(vdpa, qid);
-	irq_bypass_unregister_producer(&vq->call_ctx.producer);
-	if (!vq->call_ctx.ctx || irq < 0)
+	if (irq < 0)
+		return;
+
+	if (!vq->call_ctx.ctx)
 		return;
 
-	vq->call_ctx.producer.token = vq->call_ctx.ctx;
 	vq->call_ctx.producer.irq = irq;
 	ret = irq_bypass_register_producer(&vq->call_ctx.producer);
 	if (unlikely(ret))
@@ -197,7 +198,7 @@
 	struct vdpa_device *vdpa = v->vdpa;
 	long size = vdpa->config->get_config_size(vdpa);
 
-	if (c->len == 0)
+	if (c->len == 0 || c->off > size)
 		return -EINVAL;
 
 	if (c->len > size - c->off)
@@ -389,7 +390,22 @@
 		if (r)
 			return r;
 
-		vq->last_avail_idx = vq_state.split.avail_index;
+		if (vhost_has_feature(vq, VIRTIO_F_RING_PACKED)) {
+			vq->last_avail_idx = vq_state.packed.last_avail_idx |
+					     (vq_state.packed.last_avail_counter << 15);
+			vq->last_used_idx = vq_state.packed.last_used_idx |
+					    (vq_state.packed.last_used_counter << 15);
+		} else {
+			vq->last_avail_idx = vq_state.split.avail_index;
+		}
+		break;
+	case VHOST_SET_VRING_CALL:
+		if (vq->call_ctx.ctx) {
+			if (ops->get_status(vdpa) &
+			    VIRTIO_CONFIG_S_DRIVER_OK)
+				vhost_vdpa_unsetup_vq_irq(v, idx);
+			vq->call_ctx.producer.token = NULL;
+		}
 		break;
 	}
 
@@ -407,21 +423,32 @@
 		break;
 
 	case VHOST_SET_VRING_BASE:
-		vq_state.split.avail_index = vq->last_avail_idx;
-		if (ops->set_vq_state(vdpa, idx, &vq_state))
-			r = -EINVAL;
+		if (vhost_has_feature(vq, VIRTIO_F_RING_PACKED)) {
+			vq_state.packed.last_avail_idx = vq->last_avail_idx & 0x7fff;
+			vq_state.packed.last_avail_counter = !!(vq->last_avail_idx & 0x8000);
+			vq_state.packed.last_used_idx = vq->last_used_idx & 0x7fff;
+			vq_state.packed.last_used_counter = !!(vq->last_used_idx & 0x8000);
+		} else {
+			vq_state.split.avail_index = vq->last_avail_idx;
+		}
+		r = ops->set_vq_state(vdpa, idx, &vq_state);
 		break;
 
 	case VHOST_SET_VRING_CALL:
 		if (vq->call_ctx.ctx) {
 			cb.callback = vhost_vdpa_virtqueue_cb;
 			cb.private = vq;
+			cb.trigger = vq->call_ctx.ctx;
+			vq->call_ctx.producer.token = vq->call_ctx.ctx;
+			if (ops->get_status(vdpa) &
+			    VIRTIO_CONFIG_S_DRIVER_OK)
+				vhost_vdpa_setup_vq_irq(v, idx);
 		} else {
 			cb.callback = NULL;
 			cb.private = NULL;
+			cb.trigger = NULL;
 		}
 		ops->set_vq_cb(vdpa, idx, &cb);
-		vhost_vdpa_setup_vq_irq(v, idx);
 		break;
 
 	case VHOST_SET_VRING_NUM:
@@ -972,6 +999,7 @@
 	for (i = 0; i < nvqs; i++) {
 		vqs[i] = &v->vqs[i];
 		vqs[i]->handle_kick = handle_vq_kick;
+		vqs[i]->call_ctx.ctx = NULL;
 	}
 	vhost_dev_init(dev, vqs, nvqs, 0, 0, 0, false,
 		       vhost_vdpa_process_iotlb_msg);
@@ -1043,13 +1071,7 @@
 
 	notify = ops->get_vq_notification(vdpa, index);
 
-	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
-	if (remap_pfn_range(vma, vmf->address & PAGE_MASK,
-			    PFN_DOWN(notify.addr), PAGE_SIZE,
-			    vma->vm_page_prot))
-		return VM_FAULT_SIGBUS;
-
-	return VM_FAULT_NOPAGE;
+	return vmf_insert_pfn(vma, vmf->address & PAGE_MASK, PFN_DOWN(notify.addr));
 }
 
 static const struct vm_operations_struct vhost_vdpa_vm_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/vhost.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/vhost.c
@@ -669,7 +669,7 @@
 }
 EXPORT_SYMBOL_GPL(vhost_dev_stop);
 
-static void vhost_clear_msg(struct vhost_dev *dev)
+void vhost_clear_msg(struct vhost_dev *dev)
 {
 	struct vhost_msg_node *node, *n;
 
@@ -687,6 +687,7 @@
 
 	spin_unlock(&dev->iotlb_lock);
 }
+EXPORT_SYMBOL_GPL(vhost_clear_msg);
 
 void vhost_dev_cleanup(struct vhost_dev *dev)
 {
@@ -1170,6 +1171,11 @@
 		goto done;
 	}
 
+	if (msg.type == VHOST_IOTLB_UPDATE && msg.size == 0) {
+		ret = -EINVAL;
+		goto done;
+	}
+
 	if (dev->msg_handler)
 		ret = dev->msg_handler(dev, &msg);
 	else
@@ -1620,17 +1626,25 @@
 			r = -EFAULT;
 			break;
 		}
-		if (s.num > 0xffff) {
-			r = -EINVAL;
-			break;
+		if (vhost_has_feature(vq, VIRTIO_F_RING_PACKED)) {
+			vq->last_avail_idx = s.num & 0xffff;
+			vq->last_used_idx = (s.num >> 16) & 0xffff;
+		} else {
+			if (s.num > 0xffff) {
+				r = -EINVAL;
+				break;
+			}
+			vq->last_avail_idx = s.num;
 		}
-		vq->last_avail_idx = s.num;
 		/* Forget the cached index value. */
 		vq->avail_idx = vq->last_avail_idx;
 		break;
 	case VHOST_GET_VRING_BASE:
 		s.index = idx;
-		s.num = vq->last_avail_idx;
+		if (vhost_has_feature(vq, VIRTIO_F_RING_PACKED))
+			s.num = (u32)vq->last_avail_idx | ((u32)vq->last_used_idx << 16);
+		else
+			s.num = vq->last_avail_idx;
 		if (copy_to_user(argp, &s, sizeof s))
 			r = -EFAULT;
 		break;
@@ -2041,7 +2055,7 @@
 	struct vhost_dev *dev = vq->dev;
 	struct vhost_iotlb *umem = dev->iotlb ? dev->iotlb : dev->umem;
 	struct iovec *_iov;
-	u64 s = 0;
+	u64 s = 0, last = addr + len - 1;
 	int ret = 0;
 
 	while ((u64)len > s) {
@@ -2051,7 +2065,7 @@
 			break;
 		}
 
-		map = vhost_iotlb_itree_first(umem, addr, addr + len - 1);
+		map = vhost_iotlb_itree_first(umem, addr, last);
 		if (map == NULL || map->start > addr) {
 			if (umem != dev->iotlb) {
 				ret = -EFAULT;
@@ -2504,9 +2518,19 @@
 	r = vhost_get_avail_idx(vq, &avail_idx);
 	if (unlikely(r))
 		return false;
+
 	vq->avail_idx = vhost16_to_cpu(vq, avail_idx);
+	if (vq->avail_idx != vq->last_avail_idx) {
+		/* Since we have updated avail_idx, the following
+		 * call to vhost_get_vq_desc() will read available
+		 * ring entries. Make sure that read happens after
+		 * the avail_idx read.
+		 */
+		smp_rmb();
+		return false;
+	}
 
-	return vq->avail_idx == vq->last_avail_idx;
+	return true;
 }
 EXPORT_SYMBOL_GPL(vhost_vq_avail_empty);
 
@@ -2568,12 +2592,11 @@
 /* Create a new message. */
 struct vhost_msg_node *vhost_new_msg(struct vhost_virtqueue *vq, int type)
 {
-	struct vhost_msg_node *node = kmalloc(sizeof *node, GFP_KERNEL);
+	/* Make sure all padding within the structure is initialized. */
+	struct vhost_msg_node *node = kzalloc(sizeof(*node), GFP_KERNEL);
 	if (!node)
 		return NULL;
 
-	/* Make sure all padding within the structure is initialized. */
-	memset(&node->msg, 0, sizeof node->msg);
 	node->vq = vq;
 	node->msg.type = type;
 	return node;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/vhost.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/vhost.h
@@ -86,13 +86,17 @@
 	/* The routine to call when the Guest pings us, or timeout. */
 	vhost_work_fn_t handle_kick;
 
-	/* Last available index we saw. */
+	/* Last available index we saw.
+	 * Values are limited to 0x7fff, and the high bit is used as
+	 * a wrap counter when using VIRTIO_F_RING_PACKED. */
 	u16 last_avail_idx;
 
 	/* Caches available index value from user. */
 	u16 avail_idx;
 
-	/* Last index we used. */
+	/* Last index we used.
+	 * Values are limited to 0x7fff, and the high bit is used as
+	 * a wrap counter when using VIRTIO_F_RING_PACKED. */
 	u16 last_used_idx;
 
 	/* Used flags */
@@ -182,6 +186,7 @@
 long vhost_vring_ioctl(struct vhost_dev *d, unsigned int ioctl, void __user *argp);
 bool vhost_vq_access_ok(struct vhost_virtqueue *vq);
 bool vhost_log_access_ok(struct vhost_dev *);
+void vhost_clear_msg(struct vhost_dev *dev);
 
 int vhost_get_vq_desc(struct vhost_virtqueue *,
 		      struct iovec iov[], unsigned int iov_count,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/vringh.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/vringh.c
@@ -123,8 +123,18 @@
 		done += partlen;
 		len -= partlen;
 		ptr += partlen;
+		iov->consumed += partlen;
+		iov->iov[iov->i].iov_len -= partlen;
+		iov->iov[iov->i].iov_base += partlen;
+
+		if (!iov->iov[iov->i].iov_len) {
+			/* Fix up old iov element then increment. */
+			iov->iov[iov->i].iov_len = iov->consumed;
+			iov->iov[iov->i].iov_base -= iov->consumed;
 
-		vringh_kiov_advance(iov, partlen);
+			iov->consumed = 0;
+			iov->i++;
+		}
 	}
 	return done;
 }
@@ -292,7 +302,7 @@
 	     int (*copy)(const struct vringh *vrh,
 			 void *dst, const void *src, size_t len))
 {
-	int err, count = 0, up_next, desc_max;
+	int err, count = 0, indirect_count = 0, up_next, desc_max;
 	struct vring_desc desc, *descs;
 	struct vringh_range range = { -1ULL, 0 }, slowrange;
 	bool slow = false;
@@ -349,7 +359,12 @@
 			continue;
 		}
 
-		if (count++ == vrh->vring.num) {
+		if (up_next == -1)
+			count++;
+		else
+			indirect_count++;
+
+		if (count > vrh->vring.num || indirect_count > desc_max) {
 			vringh_bad("Descriptor loop in %p", descs);
 			err = -ELOOP;
 			goto fail;
@@ -411,6 +426,7 @@
 				i = return_from_indirect(vrh, &up_next,
 							 &descs, &desc_max);
 				slow = false;
+				indirect_count = 0;
 			} else
 				break;
 		}
@@ -1095,7 +1111,7 @@
 	struct vhost_iotlb_map *map;
 	struct vhost_iotlb *iotlb = vrh->iotlb;
 	int ret = 0;
-	u64 s = 0;
+	u64 s = 0, last = addr + len - 1;
 
 	spin_lock(vrh->iotlb_lock);
 
@@ -1107,8 +1123,7 @@
 			break;
 		}
 
-		map = vhost_iotlb_itree_first(iotlb, addr,
-					      addr + len - 1);
+		map = vhost_iotlb_itree_first(iotlb, addr, last);
 		if (!map || map->start > addr) {
 			ret = -EINVAL;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vhost/vsock.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vhost/vsock.c
@@ -393,7 +393,7 @@
 		return NULL;
 	}
 
-	pkt->buf = kmalloc(pkt->len, GFP_KERNEL);
+	pkt->buf = kvmalloc(pkt->len, GFP_KERNEL);
 	if (!pkt->buf) {
 		kfree(pkt);
 		return NULL;
@@ -554,7 +554,7 @@
 			virtio_transport_free_pkt(pkt);
 
 		len += sizeof(pkt->hdr);
-		vhost_add_used(vq, head, len);
+		vhost_add_used(vq, head, 0);
 		total_len += len;
 		added = true;
 	} while(likely(!vhost_exceeds_weight(vq, ++pkts, total_len)));
@@ -633,16 +633,18 @@
 	return ret;
 }
 
-static int vhost_vsock_stop(struct vhost_vsock *vsock)
+static int vhost_vsock_stop(struct vhost_vsock *vsock, bool check_owner)
 {
 	size_t i;
-	int ret;
+	int ret = 0;
 
 	mutex_lock(&vsock->dev.mutex);
 
-	ret = vhost_dev_check_owner(&vsock->dev);
-	if (ret)
-		goto err;
+	if (check_owner) {
+		ret = vhost_dev_check_owner(&vsock->dev);
+		if (ret)
+			goto err;
+	}
 
 	for (i = 0; i < ARRAY_SIZE(vsock->vqs); i++) {
 		struct vhost_virtqueue *vq = &vsock->vqs[i];
@@ -682,6 +684,7 @@
 	}
 
 	vsock->guest_cid = 0; /* no CID assigned yet */
+	vsock->seqpacket_allow = false;
 
 	atomic_set(&vsock->queued_replies, 0);
 
@@ -755,9 +758,15 @@
 
 	/* Iterating over all connections for all CIDs to find orphans is
 	 * inefficient.  Room for improvement here. */
-	vsock_for_each_connected_socket(vhost_vsock_reset_orphans);
+	vsock_for_each_connected_socket(&vhost_transport.transport,
+					vhost_vsock_reset_orphans);
 
-	vhost_vsock_stop(vsock);
+	/* Don't check the owner, because we are in the release path, so we
+	 * need to stop the vsock device in any case.
+	 * vhost_vsock_stop() can not fail in this case, so we don't need to
+	 * check the return code.
+	 */
+	vhost_vsock_stop(vsock, false);
 	vhost_vsock_flush(vsock);
 	vhost_dev_stop(&vsock->dev);
 
@@ -834,8 +843,7 @@
 			goto err;
 	}
 
-	if (features & (1ULL << VIRTIO_VSOCK_F_SEQPACKET))
-		vsock->seqpacket_allow = true;
+	vsock->seqpacket_allow = features & (1ULL << VIRTIO_VSOCK_F_SEQPACKET);
 
 	for (i = 0; i < ARRAY_SIZE(vsock->vqs); i++) {
 		vq = &vsock->vqs[i];
@@ -872,7 +880,7 @@
 		if (start)
 			return vhost_vsock_start(vsock);
 		else
-			return vhost_vsock_stop(vsock);
+			return vhost_vsock_stop(vsock, true);
 	case VHOST_GET_FEATURES:
 		features = VHOST_VSOCK_FEATURES;
 		if (copy_to_user(argp, &features, sizeof(features)))
@@ -960,7 +968,14 @@
 				  VSOCK_TRANSPORT_F_H2G);
 	if (ret < 0)
 		return ret;
-	return misc_register(&vhost_vsock_misc);
+
+	ret = misc_register(&vhost_vsock_misc);
+	if (ret) {
+		vsock_core_unregister(&vhost_transport.transport);
+		return ret;
+	}
+
+	return 0;
 };
 
 static void __exit vhost_vsock_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/backlight.c
@@ -688,12 +688,6 @@
 			of_node_put(np);
 			if (!bd)
 				return ERR_PTR(-EPROBE_DEFER);
-			/*
-			 * Note: gpio_backlight uses brightness as
-			 * power state during probe
-			 */
-			if (!bd->props.brightness)
-				bd->props.brightness = bd->props.max_brightness;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/bd6107.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/bd6107.c
@@ -104,7 +104,7 @@
 {
 	struct bd6107 *bd = bl_get_data(backlight);
 
-	return bd->pdata->fbdev == NULL || bd->pdata->fbdev == info->dev;
+	return bd->pdata->fbdev == NULL || bd->pdata->fbdev == info->device;
 }
 
 static const struct backlight_ops bd6107_backlight_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/da9052_bl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/da9052_bl.c
@@ -117,6 +117,7 @@
 	wleds->led_reg = platform_get_device_id(pdev)->driver_data;
 	wleds->state = DA9052_WLEDS_OFF;
 
+	memset(&props, 0, sizeof(struct backlight_properties));
 	props.type = BACKLIGHT_RAW;
 	props.max_brightness = DA9052_MAX_BRIGHTNESS;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/gpio_backlight.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/gpio_backlight.c
@@ -35,7 +35,7 @@
 {
 	struct gpio_backlight *gbl = bl_get_data(bl);
 
-	return gbl->fbdev == NULL || gbl->fbdev == info->dev;
+	return gbl->fbdev == NULL || gbl->fbdev == info->device;
 }
 
 static const struct backlight_ops gpio_backlight_ops = {
@@ -87,8 +87,7 @@
 		/* Not booted with device tree or no phandle link to the node */
 		bl->props.power = def_value ? FB_BLANK_UNBLANK
 					    : FB_BLANK_POWERDOWN;
-	else if (gpiod_get_direction(gbl->gpiod) == 0 &&
-		 gpiod_get_value_cansleep(gbl->gpiod) == 0)
+	else if (gpiod_get_value_cansleep(gbl->gpiod) == 0)
 		bl->props.power = FB_BLANK_POWERDOWN;
 	else
 		bl->props.power = FB_BLANK_UNBLANK;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/lm3630a_bl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/lm3630a_bl.c
@@ -231,7 +231,7 @@
 		if (rval < 0)
 			goto out_i2c_err;
 		brightness |= rval;
-		goto out;
+		return brightness;
 	}
 
 	/* disable sleep */
@@ -242,11 +242,8 @@
 	rval = lm3630a_read(pchip, REG_BRT_A);
 	if (rval < 0)
 		goto out_i2c_err;
-	brightness = rval;
+	return rval;
 
-out:
-	bl->props.brightness = brightness;
-	return bl->props.brightness;
 out_i2c_err:
 	dev_err(pchip->dev, "i2c failed to access register\n");
 	return 0;
@@ -306,7 +303,7 @@
 		if (rval < 0)
 			goto out_i2c_err;
 		brightness |= rval;
-		goto out;
+		return brightness;
 	}
 
 	/* disable sleep */
@@ -317,11 +314,8 @@
 	rval = lm3630a_read(pchip, REG_BRT_B);
 	if (rval < 0)
 		goto out_i2c_err;
-	brightness = rval;
+	return rval;
 
-out:
-	bl->props.brightness = brightness;
-	return bl->props.brightness;
 out_i2c_err:
 	dev_err(pchip->dev, "i2c failed to access register\n");
 	return 0;
@@ -339,6 +333,7 @@
 	struct backlight_properties props;
 	const char *label;
 
+	memset(&props, 0, sizeof(struct backlight_properties));
 	props.type = BACKLIGHT_RAW;
 	if (pdata->leda_ctrl != LM3630A_LEDA_DISABLE) {
 		props.brightness = pdata->leda_init_brt;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/lm3639_bl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/lm3639_bl.c
@@ -339,6 +339,7 @@
 	}
 
 	/* backlight */
+	memset(&props, 0, sizeof(struct backlight_properties));
 	props.type = BACKLIGHT_RAW;
 	props.brightness = pdata->init_brt_led;
 	props.max_brightness = pdata->max_brt_led;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/lp8788_bl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/lp8788_bl.c
@@ -191,6 +191,7 @@
 	int init_brt;
 	char *name;
 
+	memset(&props, 0, sizeof(struct backlight_properties));
 	props.type = BACKLIGHT_PLATFORM;
 	props.max_brightness = MAX_BRIGHTNESS;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/lv5207lp.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/lv5207lp.c
@@ -67,7 +67,7 @@
 {
 	struct lv5207lp *lv = bl_get_data(backlight);
 
-	return lv->pdata->fbdev == NULL || lv->pdata->fbdev == info->dev;
+	return lv->pdata->fbdev == NULL || lv->pdata->fbdev == info->device;
 }
 
 static const struct backlight_ops lv5207lp_backlight_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/backlight/qcom-wled.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/backlight/qcom-wled.c
@@ -231,14 +231,14 @@
 static int wled3_set_brightness(struct wled *wled, u16 brightness)
 {
 	int rc, i;
-	u8 v[2];
+	__le16 v;
 
-	v[0] = brightness & 0xff;
-	v[1] = (brightness >> 8) & 0xf;
+	v = cpu_to_le16(brightness & WLED3_SINK_REG_BRIGHT_MAX);
 
 	for (i = 0;  i < wled->cfg.num_strings; ++i) {
 		rc = regmap_bulk_write(wled->regmap, wled->ctrl_addr +
-				       WLED3_SINK_REG_BRIGHT(i), v, 2);
+				       WLED3_SINK_REG_BRIGHT(wled->cfg.enabled_strings[i]),
+				       &v, sizeof(v));
 		if (rc < 0)
 			return rc;
 	}
@@ -250,18 +250,18 @@
 {
 	int rc, i;
 	u16 low_limit = wled->max_brightness * 4 / 1000;
-	u8 v[2];
+	__le16 v;
 
 	/* WLED4's lower limit of operation is 0.4% */
 	if (brightness > 0 && brightness < low_limit)
 		brightness = low_limit;
 
-	v[0] = brightness & 0xff;
-	v[1] = (brightness >> 8) & 0xf;
+	v = cpu_to_le16(brightness & WLED3_SINK_REG_BRIGHT_MAX);
 
 	for (i = 0;  i < wled->cfg.num_strings; ++i) {
 		rc = regmap_bulk_write(wled->regmap, wled->sink_addr +
-				       WLED4_SINK_REG_BRIGHT(i), v, 2);
+				       WLED4_SINK_REG_BRIGHT(wled->cfg.enabled_strings[i]),
+				       &v, sizeof(v));
 		if (rc < 0)
 			return rc;
 	}
@@ -273,21 +273,20 @@
 {
 	int rc, offset;
 	u16 low_limit = wled->max_brightness * 1 / 1000;
-	u8 v[2];
+	__le16 v;
 
 	/* WLED5's lower limit is 0.1% */
 	if (brightness < low_limit)
 		brightness = low_limit;
 
-	v[0] = brightness & 0xff;
-	v[1] = (brightness >> 8) & 0x7f;
+	v = cpu_to_le16(brightness & WLED5_SINK_REG_BRIGHT_MAX_15B);
 
 	offset = (wled->cfg.mod_sel == MOD_A) ?
 		  WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB :
 		  WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB;
 
 	rc = regmap_bulk_write(wled->regmap, wled->sink_addr + offset,
-			       v, 2);
+			       &v, sizeof(v));
 	return rc;
 }
 
@@ -572,7 +571,7 @@
 
 static void wled_auto_string_detection(struct wled *wled)
 {
-	int rc = 0, i, delay_time_us;
+	int rc = 0, i, j, delay_time_us;
 	u32 sink_config = 0;
 	u8 sink_test = 0, sink_valid = 0, val;
 	bool fault_set;
@@ -619,14 +618,15 @@
 
 	/* Iterate through the strings one by one */
 	for (i = 0; i < wled->cfg.num_strings; i++) {
-		sink_test = BIT((WLED4_SINK_REG_CURR_SINK_SHFT + i));
+		j = wled->cfg.enabled_strings[i];
+		sink_test = BIT((WLED4_SINK_REG_CURR_SINK_SHFT + j));
 
 		/* Enable feedback control */
 		rc = regmap_write(wled->regmap, wled->ctrl_addr +
-				  WLED3_CTRL_REG_FEEDBACK_CONTROL, i + 1);
+				  WLED3_CTRL_REG_FEEDBACK_CONTROL, j + 1);
 		if (rc < 0) {
 			dev_err(wled->dev, "Failed to enable feedback for SINK %d rc = %d\n",
-				i + 1, rc);
+				j + 1, rc);
 			goto failed_detect;
 		}
 
@@ -635,7 +635,7 @@
 				  WLED4_SINK_REG_CURR_SINK, sink_test);
 		if (rc < 0) {
 			dev_err(wled->dev, "Failed to configure SINK %d rc=%d\n",
-				i + 1, rc);
+				j + 1, rc);
 			goto failed_detect;
 		}
 
@@ -662,7 +662,7 @@
 
 		if (fault_set)
 			dev_dbg(wled->dev, "WLED OVP fault detected with SINK %d\n",
-				i + 1);
+				j + 1);
 		else
 			sink_valid |= sink_test;
 
@@ -702,15 +702,16 @@
 	/* Enable valid sinks */
 	if (wled->version == 4) {
 		for (i = 0; i < wled->cfg.num_strings; i++) {
+			j = wled->cfg.enabled_strings[i];
 			if (sink_config &
-			    BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
+			    BIT(WLED4_SINK_REG_CURR_SINK_SHFT + j))
 				val = WLED4_SINK_REG_STR_MOD_MASK;
 			else
 				/* Disable modulator_en for unused sink */
 				val = 0;
 
 			rc = regmap_write(wled->regmap, wled->sink_addr +
-					  WLED4_SINK_REG_STR_MOD_EN(i), val);
+					  WLED4_SINK_REG_STR_MOD_EN(j), val);
 			if (rc < 0) {
 				dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
 					rc);
@@ -1256,21 +1257,6 @@
 	.size = 16,
 };
 
-static u32 wled3_num_strings_values_fn(u32 idx)
-{
-	return idx + 1;
-}
-
-static const struct wled_var_cfg wled3_num_strings_cfg = {
-	.fn = wled3_num_strings_values_fn,
-	.size = 3,
-};
-
-static const struct wled_var_cfg wled4_num_strings_cfg = {
-	.fn = wled3_num_strings_values_fn,
-	.size = 4,
-};
-
 static u32 wled3_switch_freq_values_fn(u32 idx)
 {
 	return 19200 / (2 * (1 + idx));
@@ -1344,11 +1330,6 @@
 			.val_ptr = &cfg->switch_freq,
 			.cfg = &wled3_switch_freq_cfg,
 		},
-		{
-			.name = "qcom,num-strings",
-			.val_ptr = &cfg->num_strings,
-			.cfg = &wled3_num_strings_cfg,
-		},
 	};
 
 	const struct wled_u32_opts wled4_opts[] = {
@@ -1372,11 +1353,6 @@
 			.val_ptr = &cfg->switch_freq,
 			.cfg = &wled3_switch_freq_cfg,
 		},
-		{
-			.name = "qcom,num-strings",
-			.val_ptr = &cfg->num_strings,
-			.cfg = &wled4_num_strings_cfg,
-		},
 	};
 
 	const struct wled_u32_opts wled5_opts[] = {
@@ -1401,11 +1377,6 @@
 			.cfg = &wled3_switch_freq_cfg,
 		},
 		{
-			.name = "qcom,num-strings",
-			.val_ptr = &cfg->num_strings,
-			.cfg = &wled4_num_strings_cfg,
-		},
-		{
 			.name = "qcom,modulator-sel",
 			.val_ptr = &cfg->mod_sel,
 			.cfg = &wled5_mod_sel_cfg,
@@ -1523,16 +1494,57 @@
 			*bool_opts[i].val_ptr = true;
 	}
 
-	cfg->num_strings = cfg->num_strings + 1;
-
 	string_len = of_property_count_elems_of_size(dev->of_node,
 						     "qcom,enabled-strings",
 						     sizeof(u32));
-	if (string_len > 0)
-		of_property_read_u32_array(dev->of_node,
+	if (string_len > 0) {
+		if (string_len > wled->max_string_count) {
+			dev_err(dev, "Cannot have more than %d strings\n",
+				wled->max_string_count);
+			return -EINVAL;
+		}
+
+		rc = of_property_read_u32_array(dev->of_node,
 						"qcom,enabled-strings",
 						wled->cfg.enabled_strings,
-						sizeof(u32));
+						string_len);
+		if (rc) {
+			dev_err(dev, "Failed to read %d elements from qcom,enabled-strings: %d\n",
+				string_len, rc);
+			return rc;
+		}
+
+		for (i = 0; i < string_len; ++i) {
+			if (wled->cfg.enabled_strings[i] >= wled->max_string_count) {
+				dev_err(dev,
+					"qcom,enabled-strings index %d at %d is out of bounds\n",
+					wled->cfg.enabled_strings[i], i);
+				return -EINVAL;
+			}
+		}
+
+		cfg->num_strings = string_len;
+	}
+
+	rc = of_property_read_u32(dev->of_node, "qcom,num-strings", &val);
+	if (!rc) {
+		if (val < 1 || val > wled->max_string_count) {
+			dev_err(dev, "qcom,num-strings must be between 1 and %d\n",
+				wled->max_string_count);
+			return -EINVAL;
+		}
+
+		if (string_len > 0) {
+			dev_warn(dev, "Only one of qcom,num-strings or qcom,enabled-strings"
+				      " should be set\n");
+			if (val > string_len) {
+				dev_err(dev, "qcom,num-strings exceeds qcom,enabled-strings\n");
+				return -EINVAL;
+			}
+		}
+
+		cfg->num_strings = val;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/console/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/console/Kconfig
@@ -23,7 +23,7 @@
 	  Say Y.
 
 config MDA_CONSOLE
-	depends on !M68K && !PARISC && ISA
+	depends on VGA_CONSOLE && ISA
 	tristate "MDA text console (dual-headed)"
 	help
 	  Say Y here if you have an old MDA or monochrome Hercules graphics
@@ -78,6 +78,26 @@
 	help
 	  Low-level framebuffer-based console driver.
 
+config FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+	bool "Enable legacy fbcon hardware acceleration code"
+	depends on FRAMEBUFFER_CONSOLE
+	default y if PARISC
+	default n
+	help
+	  This option enables the fbcon (framebuffer text-based) hardware
+	  acceleration for graphics drivers which were written for the fbdev
+	  graphics interface.
+
+	  On modern machines, on mainstream machines (like x86-64) or when
+	  using a modern Linux distribution those fbdev drivers usually aren't used.
+	  So enabling this option wouldn't have any effect, which is why you want
+	  to disable this option on such newer machines.
+
+	  If you compile this kernel for older machines which still require the
+	  fbdev drivers, you may want to say Y.
+
+	  If unsure, select n.
+
 config FRAMEBUFFER_CONSOLE_DETECT_PRIMARY
        bool "Map the console to the primary display device"
        depends on FRAMEBUFFER_CONSOLE
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/console/sticon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/console/sticon.c
@@ -46,6 +46,7 @@
 #include <linux/slab.h>
 #include <linux/font.h>
 #include <linux/crc32.h>
+#include <linux/fb.h>
 
 #include <asm/io.h>
 
@@ -332,13 +333,13 @@
 			    bool blink, bool underline, bool reverse,
 			    bool italic)
 {
-    u8 attr = ((color & 0x70) >> 1) | ((color & 7));
+	u8 fg = color & 7;
+	u8 bg = (color & 0x70) >> 4;
 
-    if (reverse) {
-	color = ((color >> 3) & 0x7) | ((color & 0x7) << 3);
-    }
-
-    return attr;
+	if (reverse)
+		return (fg << 3) | bg;
+	else
+		return (bg << 3) | fg;
 }
 
 static void sticon_invert_region(struct vc_data *conp, u16 *p, int count)
@@ -392,7 +393,9 @@
     for (i = 0; i < MAX_NR_CONSOLES; i++)
 	font_data[i] = STI_DEF_FONT;
 
-    pr_info("sticon: Initializing STI text console.\n");
+    pr_info("sticon: Initializing STI text console on %s at [%s]\n",
+	sticon_sti->sti_data->inq_outptr.dev_name,
+	sticon_sti->pa_path);
     console_lock();
     err = do_take_over_console(&sti_con, 0, MAX_NR_CONSOLES - 1,
 		PAGE0->mem_cons.cl_class != CL_DUPLEX);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/console/sticore.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/console/sticore.c
@@ -30,10 +30,11 @@
 #include <asm/pdc.h>
 #include <asm/cacheflush.h>
 #include <asm/grfioctl.h>
+#include <asm/fb.h>
 
 #include "../fbdev/sticore.h"
 
-#define STI_DRIVERVERSION "Version 0.9b"
+#define STI_DRIVERVERSION "Version 0.9c"
 
 static struct sti_struct *default_sti __read_mostly;
 
@@ -502,7 +503,7 @@
 	if (!fbfont)
 		return NULL;
 
-	pr_info("STI selected %ux%u framebuffer font %s for sticon\n",
+	pr_info("    using %ux%u framebuffer font %s\n",
 			fbfont->width, fbfont->height, fbfont->name);
 			
 	bpc = ((fbfont->width+7)/8) * fbfont->height; 
@@ -946,6 +947,7 @@
 
 static void sticore_check_for_default_sti(struct sti_struct *sti, char *path)
 {
+	pr_info("    located at [%s]\n", sti->pa_path);
 	if (strcmp (path, default_sti_path) == 0)
 		default_sti = sti;
 }
@@ -957,7 +959,6 @@
  */
 static int __init sticore_pa_init(struct parisc_device *dev)
 {
-	char pa_path[21];
 	struct sti_struct *sti = NULL;
 	int hpa = dev->hpa.start;
 
@@ -970,8 +971,8 @@
 	if (!sti)
 		return 1;
 
-	print_pa_hwpath(dev, pa_path);
-	sticore_check_for_default_sti(sti, pa_path);
+	print_pa_hwpath(dev, sti->pa_path);
+	sticore_check_for_default_sti(sti, sti->pa_path);
 	return 0;
 }
 
@@ -1007,9 +1008,8 @@
 
 	sti = sti_try_rom_generic(rom_base, fb_base, pd);
 	if (sti) {
-		char pa_path[30];
-		print_pci_hwpath(pd, pa_path);
-		sticore_check_for_default_sti(sti, pa_path);
+		print_pci_hwpath(pd, sti->pa_path);
+		sticore_check_for_default_sti(sti, sti->pa_path);
 	}
 	
 	if (!sti) {
@@ -1127,6 +1127,24 @@
 	return ret;
 }
 
+#if defined(CONFIG_FB_STI)
+/* check if given fb_info is the primary device */
+int fb_is_primary_device(struct fb_info *info)
+{
+	struct sti_struct *sti;
+
+	sti = sti_get_rom(0);
+
+	/* if no built-in graphics card found, allow any fb driver as default */
+	if (!sti)
+		return true;
+
+	/* return true if it's the default built-in framebuffer driver */
+	return (sti->info == info);
+}
+EXPORT_SYMBOL(fb_is_primary_device);
+#endif
+
 MODULE_AUTHOR("Philipp Rumpf, Helge Deller, Thomas Bogendoerfer");
 MODULE_DESCRIPTION("Core STI driver for HP's NGLE series graphics cards in HP PARISC machines");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/console/vgacon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/console/vgacon.c
@@ -366,11 +366,17 @@
 	struct uni_pagedir *p;
 
 	/*
-	 * We cannot be loaded as a module, therefore init is always 1,
-	 * but vgacon_init can be called more than once, and init will
-	 * not be 1.
+	 * We cannot be loaded as a module, therefore init will be 1
+	 * if we are the default console, however if we are a fallback
+	 * console, for example if fbcon has failed registration, then
+	 * init will be 0, so we need to make sure our boot parameters
+	 * have been copied to the console structure for vgacon_resize
+	 * ultimately called by vc_resize.  Any subsequent calls to
+	 * vgacon_init init will have init set to 0 too.
 	 */
 	c->vc_can_do_color = vga_can_do_color;
+	c->vc_scan_lines = vga_scan_lines;
+	c->vc_font.height = c->vc_cell_height = vga_video_font_height;
 
 	/* set dimensions manually if init != 0 since vc_resize() will fail */
 	if (init) {
@@ -379,8 +385,6 @@
 	} else
 		vc_resize(c, vga_video_num_columns, vga_video_num_lines);
 
-	c->vc_scan_lines = vga_scan_lines;
-	c->vc_font.height = c->vc_cell_height = vga_video_font_height;
 	c->vc_complement_mask = 0x7700;
 	if (vga_512_chars)
 		c->vc_hi_font_mask = 0x0800;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/Kconfig
@@ -606,6 +606,7 @@
 config FB_UVESA
 	tristate "Userspace VESA VGA graphics support"
 	depends on FB && CONNECTOR
+	depends on !UML
 	select FB_CFB_FILLRECT
 	select FB_CFB_COPYAREA
 	select FB_CFB_IMAGEBLIT
@@ -2015,7 +2016,7 @@
 	depends on FB && MIPS_COBALT
 
 config FB_SH7760
-	bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
+	tristate "SH7760/SH7763/SH7720/SH7721 LCDC support"
 	depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
 		|| CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
 	select FB_CFB_FILLRECT
@@ -2218,7 +2219,6 @@
 	select FB_SYS_COPYAREA
 	select FB_SYS_IMAGEBLIT
 	select FB_DEFERRED_IO
-	select PWM
 	select FB_BACKLIGHT
 	help
 	  This driver implements support for the Solomon SSD1307
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/amba-clcd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/amba-clcd.c
@@ -698,16 +698,18 @@
 		return -ENODEV;
 
 	panel = of_graph_get_remote_port_parent(endpoint);
-	if (!panel)
-		return -ENODEV;
+	if (!panel) {
+		err = -ENODEV;
+		goto out_endpoint_put;
+	}
 
 	err = clcdfb_of_get_backlight(&fb->dev->dev, fb->panel);
 	if (err)
-		return err;
+		goto out_panel_put;
 
 	err = clcdfb_of_get_mode(&fb->dev->dev, panel, fb->panel);
 	if (err)
-		return err;
+		goto out_panel_put;
 
 	err = of_property_read_u32(fb->dev->dev.of_node, "max-memory-bandwidth",
 			&max_bandwidth);
@@ -736,11 +738,21 @@
 
 	if (of_property_read_u32_array(endpoint,
 			"arm,pl11x,tft-r0g0b0-pads",
-			tft_r0b0g0, ARRAY_SIZE(tft_r0b0g0)) != 0)
-		return -ENOENT;
+			tft_r0b0g0, ARRAY_SIZE(tft_r0b0g0)) != 0) {
+		err = -ENOENT;
+		goto out_panel_put;
+	}
+
+	of_node_put(panel);
+	of_node_put(endpoint);
 
 	return clcdfb_of_init_tft_panel(fb, tft_r0b0g0[0],
 					tft_r0b0g0[1],  tft_r0b0g0[2]);
+out_panel_put:
+	of_node_put(panel);
+out_endpoint_put:
+	of_node_put(endpoint);
+	return err;
 }
 
 static int clcdfb_of_vram_setup(struct clcd_fb *fb)
@@ -758,12 +770,15 @@
 		return -ENODEV;
 
 	fb->fb.screen_base = of_iomap(memory, 0);
-	if (!fb->fb.screen_base)
+	if (!fb->fb.screen_base) {
+		of_node_put(memory);
 		return -ENOMEM;
+	}
 
 	fb->fb.fix.smem_start = of_translate_address(memory,
 			of_get_address(memory, 0, &size, NULL));
 	fb->fb.fix.smem_len = size;
+	of_node_put(memory);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/arcfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/arcfb.c
@@ -523,7 +523,7 @@
 
 	info = framebuffer_alloc(sizeof(struct arcfb_par), &dev->dev);
 	if (!info)
-		goto err;
+		goto err_fb_alloc;
 
 	info->screen_base = (char __iomem *)videomemory;
 	info->fbops = &arcfb_ops;
@@ -535,7 +535,7 @@
 
 	if (!dio_addr || !cio_addr || !c2io_addr) {
 		printk(KERN_WARNING "no IO addresses supplied\n");
-		goto err1;
+		goto err_addr;
 	}
 	par->dio_addr = dio_addr;
 	par->cio_addr = cio_addr;
@@ -551,12 +551,12 @@
 			printk(KERN_INFO
 				"arcfb: Failed req IRQ %d\n", par->irq);
 			retval = -EBUSY;
-			goto err1;
+			goto err_addr;
 		}
 	}
 	retval = register_framebuffer(info);
 	if (retval < 0)
-		goto err1;
+		goto err_register_fb;
 	platform_set_drvdata(dev, info);
 	fb_info(info, "Arc frame buffer device, using %dK of video memory\n",
 		videomemorysize >> 10);
@@ -580,9 +580,12 @@
 	}
 
 	return 0;
-err1:
+
+err_register_fb:
+	free_irq(par->irq, info);
+err_addr:
 	framebuffer_release(info);
-err:
+err_fb_alloc:
 	vfree(videomemory);
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/arkfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/arkfb.c
@@ -778,7 +778,12 @@
 		return -EINVAL;
 	}
 
-	ark_set_pixclock(info, (hdiv * info->var.pixclock) / hmul);
+	value = (hdiv * info->var.pixclock) / hmul;
+	if (!value) {
+		fb_dbg(info, "invalid pixclock\n");
+		value = 1;
+	}
+	ark_set_pixclock(info, value);
 	svga_set_timings(par->state.vgabase, &ark_timing_regs, &(info->var), hmul, hdiv,
 			 (info->var.vmode & FB_VMODE_DOUBLE)     ? 2 : 1,
 			 (info->var.vmode & FB_VMODE_INTERLACED) ? 2 : 1,
@@ -789,6 +794,8 @@
 	value = ((value * hmul / hdiv) / 8) - 5;
 	vga_wcrt(par->state.vgabase, 0x42, (value + 1) / 2);
 
+	if (screen_size > info->screen_size)
+		screen_size = info->screen_size;
 	memset_io(info->screen_base, 0x00, screen_size);
 	/* Device and screen back on */
 	svga_wcrt_mask(par->state.vgabase, 0x17, 0x80, 0x80);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/atafb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/atafb.c
@@ -1683,9 +1683,9 @@
 			   ((blue & 0xfc00) >> 8));
 	if (regno < 16) {
 		shifter_tt.color_reg[regno] =
-			(((red & 0xe000) >> 13) | ((red & 0x1000) >> 12) << 8) |
-			(((green & 0xe000) >> 13) | ((green & 0x1000) >> 12) << 4) |
-			((blue & 0xe000) >> 13) | ((blue & 0x1000) >> 12);
+			((((red & 0xe000) >> 13)   | ((red & 0x1000) >> 12)) << 8)   |
+			((((green & 0xe000) >> 13) | ((green & 0x1000) >> 12)) << 4) |
+			   ((blue & 0xe000) >> 13) | ((blue & 0x1000) >> 12);
 		((u32 *)info->pseudo_palette)[regno] = ((red & 0xf800) |
 						       ((green & 0xfc00) >> 5) |
 						       ((blue & 0xf800) >> 11));
@@ -1971,9 +1971,9 @@
 	green >>= 12;
 	if (ATARIHW_PRESENT(EXTD_SHIFTER))
 		shifter_tt.color_reg[regno] =
-			(((red & 0xe) >> 1) | ((red & 1) << 3) << 8) |
-			(((green & 0xe) >> 1) | ((green & 1) << 3) << 4) |
-			((blue & 0xe) >> 1) | ((blue & 1) << 3);
+			((((red & 0xe)   >> 1) | ((red & 1)   << 3)) << 8) |
+			((((green & 0xe) >> 1) | ((green & 1) << 3)) << 4) |
+			  ((blue & 0xe)  >> 1) | ((blue & 1)  << 3);
 	else
 		shifter_tt.color_reg[regno] =
 			((red & 0xe) << 7) |
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/atmel_lcdfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/atmel_lcdfb.c
@@ -1062,15 +1062,16 @@
 
 	INIT_LIST_HEAD(&info->modelist);
 
-	if (pdev->dev.of_node) {
-		ret = atmel_lcdfb_of_init(sinfo);
-		if (ret)
-			goto free_info;
-	} else {
+	if (!pdev->dev.of_node) {
 		dev_err(dev, "cannot get default configuration\n");
 		goto free_info;
 	}
 
+	ret = atmel_lcdfb_of_init(sinfo);
+	if (ret)
+		goto free_info;
+
+	ret = -ENODEV;
 	if (!sinfo->config)
 		goto free_info;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/aty/atyfb_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/aty/atyfb_base.c
@@ -3447,11 +3447,15 @@
 	}
 
 	info->fix.mmio_start = raddr;
+#if defined(__i386__) || defined(__ia64__)
 	/*
 	 * By using strong UC we force the MTRR to never have an
 	 * effect on the MMIO region on both non-PAT and PAT systems.
 	 */
 	par->ati_regbase = ioremap_uc(info->fix.mmio_start, 0x1000);
+#else
+	par->ati_regbase = ioremap(info->fix.mmio_start, 0x1000);
+#endif
 	if (par->ati_regbase == NULL)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/au1100fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/au1100fb.c
@@ -137,13 +137,15 @@
 	 */
 int au1100fb_setmode(struct au1100fb_device *fbdev)
 {
-	struct fb_info *info = &fbdev->info;
+	struct fb_info *info;
 	u32 words;
 	int index;
 
 	if (!fbdev)
 		return -EINVAL;
 
+	info = &fbdev->info;
+
 	/* Update var-dependent FB info */
 	if (panel_is_active(fbdev->panel) || panel_is_color(fbdev->panel)) {
 		if (info->var.bits_per_pixel <= 8) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/au1200fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/au1200fb.c
@@ -1040,6 +1040,9 @@
 	u32 pixclock;
 	int screen_size, plane;
 
+	if (!var->pixclock)
+		return -EINVAL;
+
 	plane = fbdev->plane;
 
 	/* Make sure that the mode respect all LCD controller and
@@ -1729,6 +1732,9 @@
 
 	/* Now hook interrupt too */
 	irq = platform_get_irq(dev, 0);
+	if (irq < 0)
+		return irq;
+
 	ret = request_irq(irq, au1200fb_handle_irq,
 			  IRQF_SHARED, "lcd", (void *)dev);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/broadsheetfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/broadsheetfb.c
@@ -929,13 +929,11 @@
 }
 
 /* this is called back from the deferred io workqueue */
-static void broadsheetfb_dpy_deferred_io(struct fb_info *info,
-				struct list_head *pagelist)
+static void broadsheetfb_dpy_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	u16 y1 = 0, h = 0;
 	int prev_index = -1;
-	struct page *cur;
-	struct fb_deferred_io *fbdefio = info->fbdefio;
+	struct fb_deferred_io_pageref *pageref;
 	int h_inc;
 	u16 yres = info->var.yres;
 	u16 xres = info->var.xres;
@@ -944,7 +942,8 @@
 	h_inc = DIV_ROUND_UP(PAGE_SIZE , xres);
 
 	/* walk the written page list and swizzle the data */
-	list_for_each_entry(cur, &fbdefio->pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *cur = pageref->page;
 		if (prev_index < 0) {
 			/* just starting so assign first page */
 			y1 = (cur->index << PAGE_SHIFT) / xres;
@@ -1058,8 +1057,9 @@
 };
 
 static struct fb_deferred_io broadsheetfb_defio = {
-	.delay		= HZ/4,
-	.deferred_io	= broadsheetfb_dpy_deferred_io,
+	.delay			= HZ/4,
+	.sort_pagereflist	= true,
+	.deferred_io		= broadsheetfb_dpy_deferred_io,
 };
 
 static int broadsheetfb_probe(struct platform_device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/chipsfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/chipsfb.c
@@ -331,7 +331,7 @@
 
 static void init_chips(struct fb_info *p, unsigned long addr)
 {
-	memset(p->screen_base, 0, 0x100000);
+	fb_memset(p->screen_base, 0, 0x100000);
 
 	p->fix = chipsfb_fix;
 	p->fix.smem_start = addr;
@@ -430,6 +430,7 @@
  err_release_fb:
 	framebuffer_release(p);
  err_disable:
+	pci_disable_device(dp);
  err_out:
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/cirrusfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/cirrusfb.c
@@ -469,7 +469,7 @@
 	return 0;
 }
 
-static int cirrusfb_check_pixclock(const struct fb_var_screeninfo *var,
+static int cirrusfb_check_pixclock(struct fb_var_screeninfo *var,
 				   struct fb_info *info)
 {
 	long freq;
@@ -478,9 +478,7 @@
 	unsigned maxclockidx = var->bits_per_pixel >> 3;
 
 	/* convert from ps to kHz */
-	freq = PICOS2KHZ(var->pixclock);
-
-	dev_dbg(info->device, "desired pixclock: %ld kHz\n", freq);
+	freq = PICOS2KHZ(var->pixclock ? : 1);
 
 	maxclock = cirrusfb_board_info[cinfo->btype].maxclock[maxclockidx];
 	cinfo->multiplexing = 0;
@@ -488,11 +486,13 @@
 	/* If the frequency is greater than we can support, we might be able
 	 * to use multiplexing for the video mode */
 	if (freq > maxclock) {
-		dev_err(info->device,
-			"Frequency greater than maxclock (%ld kHz)\n",
-			maxclock);
-		return -EINVAL;
+		var->pixclock = KHZ2PICOS(maxclock);
+
+		while ((freq = PICOS2KHZ(var->pixclock)) > maxclock)
+			var->pixclock++;
 	}
+	dev_dbg(info->device, "desired pixclock: %ld kHz\n", freq);
+
 	/*
 	 * Additional constraint: 8bpp uses DAC clock doubling to allow maximum
 	 * pixel clock
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/controlfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/controlfb.c
@@ -67,7 +67,9 @@
 #define out_8(addr, val)	(void)(val)
 #define in_le32(addr)		0
 #define out_le32(addr, val)	(void)(val)
+#ifndef pgprot_cached_wthru
 #define pgprot_cached_wthru(prot) (prot)
+#endif
 #else
 static void invalid_vram_cache(void __force *addr)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/bitblit.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/bitblit.c
@@ -247,6 +247,9 @@
 
 	cursor.set = 0;
 
+	if (!vc->vc_font.data)
+		return;
+
  	c = scr_readw((u16 *) vc->vc_pos);
 	attribute = get_attribute(info, c);
 	src = vc->vc_font.data + ((c & charmask) * (w * vc->vc_font.height));
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fb_defio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fb_defio.c
@@ -36,6 +36,60 @@
 	return page;
 }
 
+static struct fb_deferred_io_pageref *fb_deferred_io_pageref_get(struct fb_info *info,
+								 unsigned long offset,
+								 struct page *page)
+{
+	struct fb_deferred_io *fbdefio = info->fbdefio;
+	struct list_head *pos = &fbdefio->pagereflist;
+	unsigned long pgoff = offset >> PAGE_SHIFT;
+	struct fb_deferred_io_pageref *pageref, *cur;
+
+	if (WARN_ON_ONCE(pgoff >= info->npagerefs))
+		return NULL; /* incorrect allocation size */
+
+	/* 1:1 mapping between pageref and page offset */
+	pageref = &info->pagerefs[pgoff];
+
+	/*
+	 * This check is to catch the case where a new process could start
+	 * writing to the same page through a new PTE. This new access
+	 * can cause a call to .page_mkwrite even if the original process'
+	 * PTE is marked writable.
+	 */
+	if (!list_empty(&pageref->list))
+		goto pageref_already_added;
+
+	pageref->page = page;
+	pageref->offset = pgoff << PAGE_SHIFT;
+
+	if (unlikely(fbdefio->sort_pagereflist)) {
+		/*
+		 * We loop through the list of pagerefs before adding in
+		 * order to keep the pagerefs sorted. This has significant
+		 * overhead of O(n^2) with n being the number of written
+		 * pages. If possible, drivers should try to work with
+		 * unsorted page lists instead.
+		 */
+		list_for_each_entry(cur, &fbdefio->pagereflist, list) {
+			if (cur->offset > pageref->offset)
+				break;
+		}
+		pos = &cur->list;
+	}
+
+	list_add_tail(&pageref->list, pos);
+
+pageref_already_added:
+	return pageref;
+}
+
+static void fb_deferred_io_pageref_put(struct fb_deferred_io_pageref *pageref,
+				       struct fb_info *info)
+{
+	list_del_init(&pageref->list);
+}
+
 /* this is to find and return the vmalloc-ed fb pages */
 static vm_fault_t fb_deferred_io_fault(struct vm_fault *vmf)
 {
@@ -59,7 +113,7 @@
 		printk(KERN_ERR "no mapping available\n");
 
 	BUG_ON(!page->mapping);
-	page->index = vmf->pgoff;
+	page->index = vmf->pgoff; /* for page_mkclean() */
 
 	vmf->page = page;
 	return 0;
@@ -78,11 +132,7 @@
 		return 0;
 
 	inode_lock(inode);
-	/* Kill off the delayed work */
-	cancel_delayed_work_sync(&info->deferred_work);
-
-	/* Run it immediately */
-	schedule_delayed_work(&info->deferred_work, 0);
+	flush_delayed_work(&info->deferred_work);
 	inode_unlock(inode);
 
 	return 0;
@@ -95,7 +145,11 @@
 	struct page *page = vmf->page;
 	struct fb_info *info = vmf->vma->vm_private_data;
 	struct fb_deferred_io *fbdefio = info->fbdefio;
-	struct page *cur;
+	struct fb_deferred_io_pageref *pageref;
+	unsigned long offset;
+	vm_fault_t ret;
+
+	offset = vmf->pgoff << PAGE_SHIFT;
 
 	/* this is a callback we get when userspace first tries to
 	write to the page. we schedule a workqueue. that workqueue
@@ -109,9 +163,15 @@
 	mutex_lock(&fbdefio->lock);
 
 	/* first write in this cycle, notify the driver */
-	if (fbdefio->first_io && list_empty(&fbdefio->pagelist))
+	if (fbdefio->first_io && list_empty(&fbdefio->pagereflist))
 		fbdefio->first_io(info);
 
+	pageref = fb_deferred_io_pageref_get(info, offset, page);
+	if (WARN_ON_ONCE(!pageref)) {
+		ret = VM_FAULT_OOM;
+		goto err_mutex_unlock;
+	}
+
 	/*
 	 * We want the page to remain locked from ->page_mkwrite until
 	 * the PTE is marked dirty to avoid page_mkclean() being called
@@ -120,30 +180,17 @@
 	 * Do this by locking the page here and informing the caller
 	 * about it with VM_FAULT_LOCKED.
 	 */
-	lock_page(page);
-
-	/* we loop through the pagelist before adding in order
-	to keep the pagelist sorted */
-	list_for_each_entry(cur, &fbdefio->pagelist, lru) {
-		/* this check is to catch the case where a new
-		process could start writing to the same page
-		through a new pte. this new access can cause the
-		mkwrite even when the original ps's pte is marked
-		writable */
-		if (unlikely(cur == page))
-			goto page_already_added;
-		else if (cur->index > page->index)
-			break;
-	}
+	lock_page(pageref->page);
 
-	list_add_tail(&page->lru, &cur->lru);
-
-page_already_added:
 	mutex_unlock(&fbdefio->lock);
 
 	/* come back after delay to process the deferred IO */
 	schedule_delayed_work(&info->deferred_work, fbdefio->delay);
 	return VM_FAULT_LOCKED;
+
+err_mutex_unlock:
+	mutex_unlock(&fbdefio->lock);
+	return ret;
 }
 
 static const struct vm_operations_struct fb_deferred_io_vm_ops = {
@@ -175,40 +222,65 @@
 /* workqueue callback */
 static void fb_deferred_io_work(struct work_struct *work)
 {
-	struct fb_info *info = container_of(work, struct fb_info,
-						deferred_work.work);
-	struct list_head *node, *next;
-	struct page *cur;
+	struct fb_info *info = container_of(work, struct fb_info, deferred_work.work);
+	struct fb_deferred_io_pageref *pageref, *next;
 	struct fb_deferred_io *fbdefio = info->fbdefio;
 
 	/* here we mkclean the pages, then do all deferred IO */
 	mutex_lock(&fbdefio->lock);
-	list_for_each_entry(cur, &fbdefio->pagelist, lru) {
+	list_for_each_entry(pageref, &fbdefio->pagereflist, list) {
+		struct page *cur = pageref->page;
 		lock_page(cur);
 		page_mkclean(cur);
 		unlock_page(cur);
 	}
 
-	/* driver's callback with pagelist */
-	fbdefio->deferred_io(info, &fbdefio->pagelist);
+	/* driver's callback with pagereflist */
+	fbdefio->deferred_io(info, &fbdefio->pagereflist);
 
 	/* clear the list */
-	list_for_each_safe(node, next, &fbdefio->pagelist) {
-		list_del(node);
-	}
+	list_for_each_entry_safe(pageref, next, &fbdefio->pagereflist, list)
+		fb_deferred_io_pageref_put(pageref, info);
+
 	mutex_unlock(&fbdefio->lock);
 }
 
-void fb_deferred_io_init(struct fb_info *info)
+int fb_deferred_io_init(struct fb_info *info)
 {
 	struct fb_deferred_io *fbdefio = info->fbdefio;
+	struct fb_deferred_io_pageref *pagerefs;
+	unsigned long npagerefs, i;
+	int ret;
 
 	BUG_ON(!fbdefio);
+
+	if (WARN_ON(!info->fix.smem_len))
+		return -EINVAL;
+
 	mutex_init(&fbdefio->lock);
 	INIT_DELAYED_WORK(&info->deferred_work, fb_deferred_io_work);
-	INIT_LIST_HEAD(&fbdefio->pagelist);
+	INIT_LIST_HEAD(&fbdefio->pagereflist);
 	if (fbdefio->delay == 0) /* set a default of 1 s */
 		fbdefio->delay = HZ;
+
+	npagerefs = DIV_ROUND_UP(info->fix.smem_len, PAGE_SIZE);
+
+	/* alloc a page ref for each page of the display memory */
+	pagerefs = kvcalloc(npagerefs, sizeof(*pagerefs), GFP_KERNEL);
+	if (!pagerefs) {
+		ret = -ENOMEM;
+		goto err;
+	}
+	for (i = 0; i < npagerefs; ++i)
+		INIT_LIST_HEAD(&pagerefs[i].list);
+	info->npagerefs = npagerefs;
+	info->pagerefs = pagerefs;
+
+	return 0;
+
+err:
+	mutex_destroy(&fbdefio->lock);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(fb_deferred_io_init);
 
@@ -216,25 +288,43 @@
 			 struct inode *inode,
 			 struct file *file)
 {
+	struct fb_deferred_io *fbdefio = info->fbdefio;
+
 	file->f_mapping->a_ops = &fb_deferred_io_aops;
+	fbdefio->open_count++;
 }
 EXPORT_SYMBOL_GPL(fb_deferred_io_open);
 
-void fb_deferred_io_cleanup(struct fb_info *info)
+static void fb_deferred_io_lastclose(struct fb_info *info)
 {
-	struct fb_deferred_io *fbdefio = info->fbdefio;
 	struct page *page;
 	int i;
 
-	BUG_ON(!fbdefio);
-	cancel_delayed_work_sync(&info->deferred_work);
+	flush_delayed_work(&info->deferred_work);
 
 	/* clear out the mapping that we setup */
 	for (i = 0 ; i < info->fix.smem_len; i += PAGE_SIZE) {
 		page = fb_deferred_io_page(info, i);
 		page->mapping = NULL;
 	}
+}
+
+void fb_deferred_io_release(struct fb_info *info)
+{
+	struct fb_deferred_io *fbdefio = info->fbdefio;
+
+	if (!--fbdefio->open_count)
+		fb_deferred_io_lastclose(info);
+}
+EXPORT_SYMBOL_GPL(fb_deferred_io_release);
+
+void fb_deferred_io_cleanup(struct fb_info *info)
+{
+	struct fb_deferred_io *fbdefio = info->fbdefio;
+
+	fb_deferred_io_lastclose(info);
 
+	kvfree(info->pagerefs);
 	mutex_destroy(&fbdefio->lock);
 }
 EXPORT_SYMBOL_GPL(fb_deferred_io_cleanup);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcon.c
@@ -115,8 +115,8 @@
    enums.  */
 static int logo_shown = FBCON_LOGO_CANSHOW;
 /* console mappings */
-static int first_fb_vc;
-static int last_fb_vc = MAX_NR_CONSOLES - 1;
+static unsigned int first_fb_vc;
+static unsigned int last_fb_vc = MAX_NR_CONSOLES - 1;
 static int fbcon_is_default = 1; 
 static int primary_device = -1;
 static int fbcon_has_console_bind;
@@ -464,10 +464,12 @@
 			options += 3;
 			if (*options)
 				first_fb_vc = simple_strtoul(options, &options, 10) - 1;
-			if (first_fb_vc < 0)
+			if (first_fb_vc >= MAX_NR_CONSOLES)
 				first_fb_vc = 0;
 			if (*options++ == '-')
 				last_fb_vc = simple_strtoul(options, &options, 10) - 1;
+			if (last_fb_vc < first_fb_vc || last_fb_vc >= MAX_NR_CONSOLES)
+				last_fb_vc = MAX_NR_CONSOLES - 1;
 			fbcon_is_default = 0; 
 			continue;
 		}
@@ -599,7 +601,7 @@
 		if (scr_readw(r) != vc->vc_video_erase_char)
 			break;
 	if (r != q && new_rows >= rows + logo_lines) {
-		save = kmalloc(array3_size(logo_lines, new_cols, 2),
+		save = kzalloc(array3_size(logo_lines, new_cols, 2),
 			       GFP_KERNEL);
 		if (save) {
 			int i = cols < new_cols ? cols : new_cols;
@@ -987,7 +989,7 @@
 	set_blitting_type(vc, info);
 
 	/* Setup default font */
-	if (!p->fontdata && !vc->vc_font.data) {
+	if (!p->fontdata) {
 		if (!fontname[0] || !(font = find_font(fontname)))
 			font = get_default_font(info->var.xres,
 						info->var.yres,
@@ -997,8 +999,6 @@
 		vc->vc_font.height = font->height;
 		vc->vc_font.data = (void *)(p->fontdata = font->data);
 		vc->vc_font.charcount = font->charcount;
-	} else {
-		p->fontdata = vc->vc_font.data;
 	}
 
 	cols = FBCON_SWAP(ops->rotate, info->var.xres, info->var.yres);
@@ -1135,13 +1135,13 @@
 
 	ops->graphics = 0;
 
-	/*
-	 * No more hw acceleration for fbcon.
-	 *
-	 * FIXME: Garbage collect all the now dead code after sufficient time
-	 * has passed.
-	 */
-	p->scrollmode = SCROLL_REDRAW;
+#ifdef CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+	if ((info->flags & FBINFO_HWACCEL_COPYAREA) &&
+	    !(info->flags & FBINFO_HWACCEL_DISABLED))
+		p->scrollmode = SCROLL_MOVE;
+	else /* default to something safe */
+		p->scrollmode = SCROLL_REDRAW;
+#endif
 
 	/*
 	 *  ++guenther: console.c:vc_allocate() relies on initializing
@@ -1165,9 +1165,9 @@
 	ops->p = &fb_display[fg_console];
 }
 
-static void fbcon_free_font(struct fbcon_display *p, bool freefont)
+static void fbcon_free_font(struct fbcon_display *p)
 {
-	if (freefont && p->userfont && p->fontdata && (--REFCOUNT(p->fontdata) == 0))
+	if (p->userfont && p->fontdata && (--REFCOUNT(p->fontdata) == 0))
 		kfree(p->fontdata - FONT_EXTRA_WORDS * sizeof(int));
 	p->fontdata = NULL;
 	p->userfont = 0;
@@ -1181,8 +1181,8 @@
 	struct fb_info *info;
 	struct fbcon_ops *ops;
 	int idx;
-	bool free_font = true;
 
+	fbcon_free_font(p);
 	idx = con2fb_map[vc->vc_num];
 
 	if (idx == -1)
@@ -1193,8 +1193,6 @@
 	if (!info)
 		goto finished;
 
-	if (info->flags & FBINFO_MISC_FIRMWARE)
-		free_font = false;
 	ops = info->fbcon_par;
 
 	if (!ops)
@@ -1206,9 +1204,8 @@
 	ops->flags &= ~FBCON_FLAGS_INIT;
 finished:
 
-	fbcon_free_font(p, free_font);
-	if (free_font)
-		vc->vc_font.data = NULL;
+	fbcon_free_font(p);
+	vc->vc_font.data = NULL;
 
 	if (vc->vc_hi_font_mask && vc->vc_screenbuf)
 		set_vc_hi_font(vc, false);
@@ -1704,9 +1701,7 @@
 	case SM_UP:
 		if (count > vc->vc_rows)	/* Maximum realistic size */
 			count = vc->vc_rows;
-		if (logo_shown >= 0)
-			goto redraw_up;
-		switch (p->scrollmode) {
+		switch (fb_scrollmode(p)) {
 		case SCROLL_MOVE:
 			fbcon_redraw_blit(vc, info, p, t, b - t - count,
 				     count);
@@ -1794,9 +1789,7 @@
 	case SM_DOWN:
 		if (count > vc->vc_rows)	/* Maximum realistic size */
 			count = vc->vc_rows;
-		if (logo_shown >= 0)
-			goto redraw_down;
-		switch (p->scrollmode) {
+		switch (fb_scrollmode(p)) {
 		case SCROLL_MOVE:
 			fbcon_redraw_blit(vc, info, p, b - 1, b - t - count,
 				     -count);
@@ -1947,6 +1940,48 @@
 		   height, width);
 }
 
+static void updatescrollmode_accel(struct fbcon_display *p,
+					struct fb_info *info,
+					struct vc_data *vc)
+{
+#ifdef CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+	struct fbcon_ops *ops = info->fbcon_par;
+	int cap = info->flags;
+	u16 t = 0;
+	int ypan = FBCON_SWAP(ops->rotate, info->fix.ypanstep,
+				  info->fix.xpanstep);
+	int ywrap = FBCON_SWAP(ops->rotate, info->fix.ywrapstep, t);
+	int yres = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
+	int vyres = FBCON_SWAP(ops->rotate, info->var.yres_virtual,
+				   info->var.xres_virtual);
+	int good_pan = (cap & FBINFO_HWACCEL_YPAN) &&
+		divides(ypan, vc->vc_font.height) && vyres > yres;
+	int good_wrap = (cap & FBINFO_HWACCEL_YWRAP) &&
+		divides(ywrap, vc->vc_font.height) &&
+		divides(vc->vc_font.height, vyres) &&
+		divides(vc->vc_font.height, yres);
+	int reading_fast = cap & FBINFO_READS_FAST;
+	int fast_copyarea = (cap & FBINFO_HWACCEL_COPYAREA) &&
+		!(cap & FBINFO_HWACCEL_DISABLED);
+	int fast_imageblit = (cap & FBINFO_HWACCEL_IMAGEBLIT) &&
+		!(cap & FBINFO_HWACCEL_DISABLED);
+
+	if (good_wrap || good_pan) {
+		if (reading_fast || fast_copyarea)
+			p->scrollmode = good_wrap ?
+				SCROLL_WRAP_MOVE : SCROLL_PAN_MOVE;
+		else
+			p->scrollmode = good_wrap ? SCROLL_REDRAW :
+				SCROLL_PAN_REDRAW;
+	} else {
+		if (reading_fast || (fast_copyarea && !fast_imageblit))
+			p->scrollmode = SCROLL_MOVE;
+		else
+			p->scrollmode = SCROLL_REDRAW;
+	}
+#endif
+}
+
 static void updatescrollmode(struct fbcon_display *p,
 					struct fb_info *info,
 					struct vc_data *vc)
@@ -1962,6 +1997,9 @@
 		p->vrows -= (yres - (fh * vc->vc_rows)) / fh;
 	if ((yres % fh) && (vyres % fh < yres % fh))
 		p->vrows--;
+
+	/* update scrollmode in case hardware acceleration is used */
+	updatescrollmode_accel(p, info, vc);
 }
 
 #define PITCH(w) (((w) + 7) >> 3)
@@ -2119,7 +2157,7 @@
 
 	updatescrollmode(p, info, vc);
 
-	switch (p->scrollmode) {
+	switch (fb_scrollmode(p)) {
 	case SCROLL_WRAP_MOVE:
 		scrollback_phys_max = p->vrows - vc->vc_rows;
 		break;
@@ -2370,15 +2408,19 @@
 	struct fb_info *info = registered_fb[con2fb_map[vc->vc_num]];
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fbcon_display *p = &fb_display[vc->vc_num];
-	int resize;
-	char *old_data = NULL;
+	int resize, ret, old_userfont, old_width, old_height, old_charcount;
+	u8 *old_data = vc->vc_font.data;
 
 	resize = (w != vc->vc_font.width) || (h != vc->vc_font.height);
-	if (p->userfont)
-		old_data = vc->vc_font.data;
 	vc->vc_font.data = (void *)(p->fontdata = data);
+	old_userfont = p->userfont;
 	if ((p->userfont = userfont))
 		REFCOUNT(data)++;
+
+	old_width = vc->vc_font.width;
+	old_height = vc->vc_font.height;
+	old_charcount = vc->vc_font.charcount;
+
 	vc->vc_font.width = w;
 	vc->vc_font.height = h;
 	vc->vc_font.charcount = charcount;
@@ -2394,16 +2436,34 @@
 		rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
 		cols /= w;
 		rows /= h;
-		vc_resize(vc, cols, rows);
+		ret = vc_resize(vc, cols, rows);
+		if (ret)
+			goto err_out;
 	} else if (con_is_visible(vc)
 		   && vc->vc_mode == KD_TEXT) {
 		fbcon_clear_margins(vc, 0);
 		update_screen(vc);
 	}
 
-	if (old_data && (--REFCOUNT(old_data) == 0))
+	if (old_userfont && (--REFCOUNT(old_data) == 0))
 		kfree(old_data - FONT_EXTRA_WORDS * sizeof(int));
 	return 0;
+
+err_out:
+	p->fontdata = old_data;
+	vc->vc_font.data = old_data;
+
+	if (userfont) {
+		p->userfont = old_userfont;
+		if (--REFCOUNT(data) == 0)
+			kfree(data - FONT_EXTRA_WORDS * sizeof(int));
+	}
+
+	vc->vc_font.width = old_width;
+	vc->vc_font.height = old_height;
+	vc->vc_font.charcount = old_charcount;
+
+	return ret;
 }
 
 /*
@@ -2435,9 +2495,17 @@
 	if (charcount != 256 && charcount != 512)
 		return -EINVAL;
 
+	/* font bigger than screen resolution ? */
+	if (w > FBCON_SWAP(info->var.rotate, info->var.xres, info->var.yres) ||
+	    h > FBCON_SWAP(info->var.rotate, info->var.yres, info->var.xres))
+		return -EINVAL;
+
+	if (font->width > 32 || font->height > 32)
+		return -EINVAL;
+
 	/* Make sure drawing engine can handle the font */
-	if (!(info->pixmap.blit_x & (1 << (font->width - 1))) ||
-	    !(info->pixmap.blit_y & (1 << (font->height - 1))))
+	if (!(info->pixmap.blit_x & BIT(font->width - 1)) ||
+	    !(info->pixmap.blit_y & BIT(font->height - 1)))
 		return -EINVAL;
 
 	/* Make sure driver can handle the font length */
@@ -2697,6 +2765,34 @@
 }
 EXPORT_SYMBOL(fbcon_update_vcs);
 
+/* let fbcon check if it supports a new screen resolution */
+int fbcon_modechange_possible(struct fb_info *info, struct fb_var_screeninfo *var)
+{
+	struct fbcon_ops *ops = info->fbcon_par;
+	struct vc_data *vc;
+	unsigned int i;
+
+	WARN_CONSOLE_UNLOCKED();
+
+	if (!ops)
+		return 0;
+
+	/* prevent setting a screen size which is smaller than font size */
+	for (i = first_fb_vc; i <= last_fb_vc; i++) {
+		vc = vc_cons[i].d;
+		if (!vc || vc->vc_mode != KD_TEXT ||
+			   registered_fb[con2fb_map[i]] != info)
+			continue;
+
+		if (vc->vc_font.width  > FBCON_SWAP(var->rotate, var->xres, var->yres) ||
+		    vc->vc_font.height > FBCON_SWAP(var->rotate, var->yres, var->xres))
+			return -EINVAL;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(fbcon_modechange_possible);
+
 int fbcon_mode_deleted(struct fb_info *info,
 		       struct fb_videomode *mode)
 {
@@ -3220,6 +3316,9 @@
 
 	console_lock();
 
+	deferred_takeover = false;
+	logo_shown = FBCON_LOGO_DONTSHOW;
+
 	for_each_registered_fb(i)
 		fbcon_fb_registered(registered_fb[i]);
 
@@ -3237,8 +3336,6 @@
 	pr_info("fbcon: Taking over console\n");
 
 	dummycon_unregister_output_notifier(&fbcon_output_nb);
-	deferred_takeover = false;
-	logo_shown = FBCON_LOGO_DONTSHOW;
 
 	/* We may get called in atomic context */
 	schedule_work(&fbcon_deferred_takeover_work);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcon.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcon.h
@@ -29,7 +29,9 @@
     /* Filled in by the low-level console driver */
     const u_char *fontdata;
     int userfont;                   /* != 0 if fontdata kmalloc()ed */
-    u_short scrollmode;             /* Scroll Method */
+#ifdef CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+    u_short scrollmode;             /* Scroll Method, use fb_scrollmode() */
+#endif
     u_short inverse;                /* != 0 text black on white as default */
     short yscroll;                  /* Hardware scrolling */
     int vrows;                      /* number of virtual rows */
@@ -208,6 +210,17 @@
 #define SCROLL_REDRAW	   0x004
 #define SCROLL_PAN_REDRAW  0x005
 
+static inline u_short fb_scrollmode(struct fbcon_display *fb)
+{
+#ifdef CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
+	return fb->scrollmode;
+#else
+	/* hardcoded to SCROLL_REDRAW if acceleration was disabled. */
+	return SCROLL_REDRAW;
+#endif
+}
+
+
 #ifdef CONFIG_FB_TILEBLITTING
 extern void fbcon_set_tileops(struct vc_data *vc, struct fb_info *info);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcon_ccw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcon_ccw.c
@@ -65,7 +65,7 @@
 {
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fb_copyarea area;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
 
 	area.sx = sy * vc->vc_font.height;
 	area.sy = vyres - ((sx + width) * vc->vc_font.width);
@@ -83,7 +83,7 @@
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fb_fillrect region;
 	int bgshift = (vc->vc_hi_font_mask) ? 13 : 12;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
 
 	region.color = attr_bgcol_ec(bgshift,vc,info);
 	region.dx = sy * vc->vc_font.height;
@@ -140,7 +140,7 @@
 	u32 cnt, pitch, size;
 	u32 attribute = get_attribute(info, scr_readw(s));
 	u8 *dst, *buf = NULL;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
 
 	if (!ops->fontbuffer)
 		return;
@@ -229,7 +229,7 @@
 	int attribute, use_sw = vc->vc_cursor_type & CUR_SW;
 	int err = 1, dx, dy;
 	char *src;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
 
 	if (!ops->fontbuffer)
 		return;
@@ -387,7 +387,7 @@
 {
 	struct fbcon_ops *ops = info->fbcon_par;
 	u32 yoffset;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
 	int err;
 
 	yoffset = (vyres - info->var.yres) - ops->var.xoffset;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcon_cw.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcon_cw.c
@@ -50,7 +50,7 @@
 {
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fb_copyarea area;
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	area.sx = vxres - ((sy + height) * vc->vc_font.height);
 	area.sy = sx * vc->vc_font.width;
@@ -68,7 +68,7 @@
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fb_fillrect region;
 	int bgshift = (vc->vc_hi_font_mask) ? 13 : 12;
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	region.color = attr_bgcol_ec(bgshift,vc,info);
 	region.dx = vxres - ((sy + height) * vc->vc_font.height);
@@ -125,7 +125,7 @@
 	u32 cnt, pitch, size;
 	u32 attribute = get_attribute(info, scr_readw(s));
 	u8 *dst, *buf = NULL;
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	if (!ops->fontbuffer)
 		return;
@@ -212,7 +212,7 @@
 	int attribute, use_sw = vc->vc_cursor_type & CUR_SW;
 	int err = 1, dx, dy;
 	char *src;
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	if (!ops->fontbuffer)
 		return;
@@ -369,7 +369,7 @@
 static int cw_update_start(struct fb_info *info)
 {
 	struct fbcon_ops *ops = info->fbcon_par;
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vxres = GETVXRES(ops->p, info);
 	u32 xoffset;
 	int err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcon_rotate.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcon_rotate.h
@@ -12,11 +12,11 @@
 #define _FBCON_ROTATE_H
 
 #define GETVYRES(s,i) ({                           \
-        (s == SCROLL_REDRAW || s == SCROLL_MOVE) ? \
+        (fb_scrollmode(s) == SCROLL_REDRAW || fb_scrollmode(s) == SCROLL_MOVE) ? \
         (i)->var.yres : (i)->var.yres_virtual; })
 
 #define GETVXRES(s,i) ({                           \
-        (s == SCROLL_REDRAW || s == SCROLL_MOVE || !(i)->fix.xpanstep) ? \
+        (fb_scrollmode(s) == SCROLL_REDRAW || fb_scrollmode(s) == SCROLL_MOVE || !(i)->fix.xpanstep) ? \
         (i)->var.xres : (i)->var.xres_virtual; })
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcon_ud.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcon_ud.c
@@ -50,8 +50,8 @@
 {
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fb_copyarea area;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	area.sy = vyres - ((sy + height) * vc->vc_font.height);
 	area.sx = vxres - ((sx + width) * vc->vc_font.width);
@@ -69,8 +69,8 @@
 	struct fbcon_ops *ops = info->fbcon_par;
 	struct fb_fillrect region;
 	int bgshift = (vc->vc_hi_font_mask) ? 13 : 12;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	region.color = attr_bgcol_ec(bgshift,vc,info);
 	region.dy = vyres - ((sy + height) * vc->vc_font.height);
@@ -162,8 +162,8 @@
 	u32 mod = vc->vc_font.width % 8, cnt, pitch, size;
 	u32 attribute = get_attribute(info, scr_readw(s));
 	u8 *dst, *buf = NULL;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	if (!ops->fontbuffer)
 		return;
@@ -259,8 +259,8 @@
 	int attribute, use_sw = vc->vc_cursor_type & CUR_SW;
 	int err = 1, dx, dy;
 	char *src;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
+	u32 vxres = GETVXRES(ops->p, info);
 
 	if (!ops->fontbuffer)
 		return;
@@ -410,8 +410,8 @@
 {
 	struct fbcon_ops *ops = info->fbcon_par;
 	int xoffset, yoffset;
-	u32 vyres = GETVYRES(ops->p->scrollmode, info);
-	u32 vxres = GETVXRES(ops->p->scrollmode, info);
+	u32 vyres = GETVYRES(ops->p, info);
+	u32 vxres = GETVXRES(ops->p, info);
 	int err;
 
 	xoffset = vxres - info->var.xres - ops->var.xoffset;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbcvt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbcvt.c
@@ -214,9 +214,11 @@
 static void fb_cvt_print_name(struct fb_cvt_data *cvt)
 {
 	u32 pixcount, pixcount_mod;
-	int cnt = 255, offset = 0, read = 0;
-	u8 *buf = kzalloc(256, GFP_KERNEL);
+	int size = 256;
+	int off = 0;
+	u8 *buf;
 
+	buf = kzalloc(size, GFP_KERNEL);
 	if (!buf)
 		return;
 
@@ -224,43 +226,30 @@
 	pixcount_mod = (cvt->xres * (cvt->yres/cvt->interlace)) % 1000000;
 	pixcount_mod /= 1000;
 
-	read = snprintf(buf+offset, cnt, "fbcvt: %dx%d@%d: CVT Name - ",
-			cvt->xres, cvt->yres, cvt->refresh);
-	offset += read;
-	cnt -= read;
-
-	if (cvt->status)
-		snprintf(buf+offset, cnt, "Not a CVT standard - %d.%03d Mega "
-			 "Pixel Image\n", pixcount, pixcount_mod);
-	else {
-		if (pixcount) {
-			read = snprintf(buf+offset, cnt, "%d", pixcount);
-			cnt -= read;
-			offset += read;
-		}
-
-		read = snprintf(buf+offset, cnt, ".%03dM", pixcount_mod);
-		cnt -= read;
-		offset += read;
+	off += scnprintf(buf + off, size - off, "fbcvt: %dx%d@%d: CVT Name - ",
+			    cvt->xres, cvt->yres, cvt->refresh);
+
+	if (cvt->status) {
+		off += scnprintf(buf + off, size - off,
+				 "Not a CVT standard - %d.%03d Mega Pixel Image\n",
+				 pixcount, pixcount_mod);
+	} else {
+		if (pixcount)
+			off += scnprintf(buf + off, size - off, "%d", pixcount);
+
+		off += scnprintf(buf + off, size - off, ".%03dM", pixcount_mod);
 
 		if (cvt->aspect_ratio == 0)
-			read = snprintf(buf+offset, cnt, "3");
+			off += scnprintf(buf + off, size - off, "3");
 		else if (cvt->aspect_ratio == 3)
-			read = snprintf(buf+offset, cnt, "4");
+			off += scnprintf(buf + off, size - off, "4");
 		else if (cvt->aspect_ratio == 1 || cvt->aspect_ratio == 4)
-			read = snprintf(buf+offset, cnt, "9");
+			off += scnprintf(buf + off, size - off, "9");
 		else if (cvt->aspect_ratio == 2)
-			read = snprintf(buf+offset, cnt, "A");
-		else
-			read = 0;
-		cnt -= read;
-		offset += read;
-
-		if (cvt->flags & FB_CVT_FLAG_REDUCED_BLANK) {
-			read = snprintf(buf+offset, cnt, "-R");
-			cnt -= read;
-			offset += read;
-		}
+			off += scnprintf(buf + off, size - off, "A");
+
+		if (cvt->flags & FB_CVT_FLAG_REDUCED_BLANK)
+			off += scnprintf(buf + off, size - off, "-R");
 	}
 
 	printk(KERN_INFO "%s\n", buf);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbmem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbmem.c
@@ -19,12 +19,14 @@
 #include <linux/kernel.h>
 #include <linux/major.h>
 #include <linux/slab.h>
+#include <linux/sysfb.h>
 #include <linux/mm.h>
 #include <linux/mman.h>
 #include <linux/vt.h>
 #include <linux/init.h>
 #include <linux/linux_logo.h>
 #include <linux/proc_fs.h>
+#include <linux/platform_device.h>
 #include <linux/seq_file.h>
 #include <linux/console.h>
 #include <linux/kmod.h>
@@ -513,7 +515,7 @@
 
 		while (n && (n * (logo->width + 8) - 8 > xres))
 			--n;
-		image.dx = (xres - n * (logo->width + 8) - 8) / 2;
+		image.dx = (xres - (n * (logo->width + 8) - 8)) / 2;
 		image.dy = y ?: (yres - logo->height) / 2;
 	} else {
 		image.dx = 0;
@@ -1019,6 +1021,16 @@
 	if (ret)
 		return ret;
 
+	/* verify that virtual resolution >= physical resolution */
+	if (var->xres_virtual < var->xres ||
+	    var->yres_virtual < var->yres) {
+		pr_warn("WARNING: fbcon: Driver '%s' missed to adjust virtual screen size (%ux%u vs. %ux%u)\n",
+			info->fix.id,
+			var->xres_virtual, var->yres_virtual,
+			var->xres, var->yres);
+		return -EINVAL;
+	}
+
 	if ((var->activate & FB_ACTIVATE_MASK) != FB_ACTIVATE_NOW)
 		return 0;
 
@@ -1107,9 +1119,13 @@
 	case FBIOPUT_VSCREENINFO:
 		if (copy_from_user(&var, argp, sizeof(var)))
 			return -EFAULT;
+		/* only for kernel-internal use */
+		var.activate &= ~FB_ACTIVATE_KD_TEXT;
 		console_lock();
 		lock_fb_info(info);
-		ret = fb_set_var(info, &var);
+		ret = fbcon_modechange_possible(info, &var);
+		if (!ret)
+			ret = fb_set_var(info, &var);
 		if (!ret)
 			fbcon_update_vcs(info, var.activate & FB_ACTIVATE_ALL);
 		unlock_fb_info(info);
@@ -1438,6 +1454,10 @@
 	struct fb_info * const info = file->private_data;
 
 	lock_fb_info(info);
+#if IS_ENABLED(CONFIG_FB_DEFERRED_IO)
+	if (info->fbdefio)
+		fb_deferred_io_release(info);
+#endif
 	if (info->fbops->fb_release)
 		info->fbops->fb_release(info,1);
 	module_put(info->fbops->owner);
@@ -1557,18 +1577,43 @@
 	/* check all firmware fbs and kick off if the base addr overlaps */
 	for_each_registered_fb(i) {
 		struct apertures_struct *gen_aper;
+		struct device *device;
 
 		if (!(registered_fb[i]->flags & FBINFO_MISC_FIRMWARE))
 			continue;
 
 		gen_aper = registered_fb[i]->apertures;
+		device = registered_fb[i]->device;
 		if (fb_do_apertures_overlap(gen_aper, a) ||
 			(primary && gen_aper && gen_aper->count &&
 			 gen_aper->ranges[0].base == VGA_FB_PHYS)) {
 
 			printk(KERN_INFO "fb%d: switching to %s from %s\n",
 			       i, name, registered_fb[i]->fix.id);
-			do_unregister_framebuffer(registered_fb[i]);
+
+			/*
+			 * If we kick-out a firmware driver, we also want to remove
+			 * the underlying platform device, such as simple-framebuffer,
+			 * VESA, EFI, etc. A native driver will then be able to
+			 * allocate the memory range.
+			 *
+			 * If it's not a platform device, at least print a warning. A
+			 * fix would add code to remove the device from the system.
+			 */
+			if (!device) {
+				/* TODO: Represent each OF framebuffer as its own
+				 * device in the device hierarchy. For now, offb
+				 * doesn't have such a device, so unregister the
+				 * framebuffer as before without warning.
+				 */
+				do_unregister_framebuffer(registered_fb[i]);
+			} else if (dev_is_platform(device)) {
+				registered_fb[i]->forced_out = true;
+				platform_device_unregister(to_platform_device(device));
+			} else {
+				pr_warn("fb%d: cannot remove device\n", i);
+				do_unregister_framebuffer(registered_fb[i]);
+			}
 		}
 	}
 }
@@ -1748,6 +1793,17 @@
 		do_free = true;
 	}
 
+	/*
+	 * If a driver asked to unregister a platform device registered by
+	 * sysfb, then can be assumed that this is a driver for a display
+	 * that is set up by the system firmware and has a generic driver.
+	 *
+	 * Drivers for devices that don't have a generic driver will never
+	 * ask for this, so let's assume that a real driver for the display
+	 * was already probed and prevent sysfb to register devices later.
+	 */
+	sysfb_disable();
+
 	mutex_lock(&registration_lock);
 	do_remove_conflicting_framebuffers(a, name, primary);
 	mutex_unlock(&registration_lock);
@@ -1760,6 +1816,53 @@
 EXPORT_SYMBOL(remove_conflicting_framebuffers);
 
 /**
+ * is_firmware_framebuffer - detect if firmware-configured framebuffer matches
+ * @a: memory range, users of which are to be checked
+ *
+ * This function checks framebuffer devices (initialized by firmware/bootloader)
+ * which use memory range described by @a. If @a matchesm the function returns
+ * true, otherwise false.
+ */
+bool is_firmware_framebuffer(struct apertures_struct *a)
+{
+	bool do_free = false;
+	bool found = false;
+	int i;
+
+	if (!a) {
+		a = alloc_apertures(1);
+		if (!a)
+			return false;
+
+		a->ranges[0].base = 0;
+		a->ranges[0].size = ~0;
+		do_free = true;
+	}
+
+	mutex_lock(&registration_lock);
+	/* check all firmware fbs and kick off if the base addr overlaps */
+	for_each_registered_fb(i) {
+		struct apertures_struct *gen_aper;
+
+		if (!(registered_fb[i]->flags & FBINFO_MISC_FIRMWARE))
+			continue;
+
+		gen_aper = registered_fb[i]->apertures;
+		if (fb_do_apertures_overlap(gen_aper, a)) {
+			found = true;
+			break;
+		}
+	}
+	mutex_unlock(&registration_lock);
+
+	if (do_free)
+		kfree(a);
+
+	return found;
+}
+EXPORT_SYMBOL(is_firmware_framebuffer);
+
+/**
  * remove_conflicting_pci_framebuffers - remove firmware-configured framebuffers for PCI devices
  * @pdev: PCI device
  * @name: requesting driver name
@@ -1848,9 +1951,13 @@
 void
 unregister_framebuffer(struct fb_info *fb_info)
 {
-	mutex_lock(&registration_lock);
+	bool forced_out = fb_info->forced_out;
+
+	if (!forced_out)
+		mutex_lock(&registration_lock);
 	do_unregister_framebuffer(fb_info);
-	mutex_unlock(&registration_lock);
+	if (!forced_out)
+		mutex_unlock(&registration_lock);
 }
 EXPORT_SYMBOL(unregister_framebuffer);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbmon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbmon.c
@@ -1311,7 +1311,7 @@
 int fb_videomode_from_videomode(const struct videomode *vm,
 				struct fb_videomode *fbmode)
 {
-	unsigned int htotal, vtotal;
+	unsigned int htotal, vtotal, total;
 
 	fbmode->xres = vm->hactive;
 	fbmode->left_margin = vm->hback_porch;
@@ -1344,8 +1344,9 @@
 	vtotal = vm->vactive + vm->vfront_porch + vm->vback_porch +
 		 vm->vsync_len;
 	/* prevent division by zero */
-	if (htotal && vtotal) {
-		fbmode->refresh = vm->pixelclock / (htotal * vtotal);
+	total = htotal * vtotal;
+	if (total) {
+		fbmode->refresh = vm->pixelclock / total;
 	/* a mode must have htotal and vtotal != 0 or it is invalid */
 	} else {
 		fbmode->refresh = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/fbsysfs.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/fbsysfs.c
@@ -80,6 +80,14 @@
 {
 	if (!info)
 		return;
+
+	if (WARN_ON(refcount_read(&info->count)))
+		return;
+
+#if IS_ENABLED(CONFIG_FB_BACKLIGHT)
+	mutex_destroy(&info->bl_curve_mutex);
+#endif
+
 	kfree(info->apertures);
 	kfree(info);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/modedb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/modedb.c
@@ -257,6 +257,11 @@
 	{ NULL, 72, 480, 300, 33386, 40, 24, 11, 19, 80, 3, 0,
 		FB_VMODE_DOUBLE },
 
+	/* 1920x1080 @ 60 Hz, 67.3 kHz hsync */
+	{ NULL, 60, 1920, 1080, 6734, 148, 88, 36, 4, 44, 5, 0,
+		FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+		FB_VMODE_NONINTERLACED },
+
 	/* 1920x1200 @ 60 Hz, 74.5 Khz hsync */
 	{ NULL, 60, 1920, 1200, 5177, 128, 336, 1, 38, 208, 3,
 		FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/core/sysimgblt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/core/sysimgblt.c
@@ -188,23 +188,29 @@
 {
 	u32 fgx = fgcolor, bgx = bgcolor, bpp = p->var.bits_per_pixel;
 	u32 ppw = 32/bpp, spitch = (image->width + 7)/8;
-	u32 bit_mask, end_mask, eorx, shift;
-	const char *s = image->data, *src;
+	u32 bit_mask, eorx, shift;
+	const u8 *s = image->data, *src;
 	u32 *dst;
-	const u32 *tab = NULL;
+	const u32 *tab;
+	size_t tablen;
+	u32 colortab[16];
 	int i, j, k;
 
 	switch (bpp) {
 	case 8:
 		tab = fb_be_math(p) ? cfb_tab8_be : cfb_tab8_le;
+		tablen = 16;
 		break;
 	case 16:
 		tab = fb_be_math(p) ? cfb_tab16_be : cfb_tab16_le;
+		tablen = 4;
 		break;
 	case 32:
-	default:
 		tab = cfb_tab32;
+		tablen = 2;
 		break;
+	default:
+		return;
 	}
 
 	for (i = ppw-1; i--; ) {
@@ -218,20 +224,62 @@
 	eorx = fgx ^ bgx;
 	k = image->width/ppw;
 
+	for (i = 0; i < tablen; ++i)
+		colortab[i] = (tab[i] & eorx) ^ bgx;
+
 	for (i = image->height; i--; ) {
 		dst = dst1;
 		shift = 8;
 		src = s;
 
-		for (j = k; j--; ) {
+		/*
+		 * Manually unroll the per-line copying loop for better
+		 * performance. This works until we processed the last
+		 * completely filled source byte (inclusive).
+		 */
+		switch (ppw) {
+		case 4: /* 8 bpp */
+			for (j = k; j >= 2; j -= 2, ++src) {
+				*dst++ = colortab[(*src >> 4) & bit_mask];
+				*dst++ = colortab[(*src >> 0) & bit_mask];
+			}
+			break;
+		case 2: /* 16 bpp */
+			for (j = k; j >= 4; j -= 4, ++src) {
+				*dst++ = colortab[(*src >> 6) & bit_mask];
+				*dst++ = colortab[(*src >> 4) & bit_mask];
+				*dst++ = colortab[(*src >> 2) & bit_mask];
+				*dst++ = colortab[(*src >> 0) & bit_mask];
+			}
+			break;
+		case 1: /* 32 bpp */
+			for (j = k; j >= 8; j -= 8, ++src) {
+				*dst++ = colortab[(*src >> 7) & bit_mask];
+				*dst++ = colortab[(*src >> 6) & bit_mask];
+				*dst++ = colortab[(*src >> 5) & bit_mask];
+				*dst++ = colortab[(*src >> 4) & bit_mask];
+				*dst++ = colortab[(*src >> 3) & bit_mask];
+				*dst++ = colortab[(*src >> 2) & bit_mask];
+				*dst++ = colortab[(*src >> 1) & bit_mask];
+				*dst++ = colortab[(*src >> 0) & bit_mask];
+			}
+			break;
+		}
+
+		/*
+		 * For image widths that are not a multiple of 8, there
+		 * are trailing pixels left on the current line. Print
+		 * them as well.
+		 */
+		for (; j--; ) {
 			shift -= ppw;
-			end_mask = tab[(*src >> shift) & bit_mask];
-			*dst++ = (end_mask & eorx) ^ bgx;
+			*dst++ = colortab[(*src >> shift) & bit_mask];
 			if (!shift) {
 				shift = 8;
-				src++;
+				++src;
 			}
 		}
+
 		dst1 += p->fix.line_length;
 		s += spitch;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/efifb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/efifb.c
@@ -47,6 +47,8 @@
 static bool request_mem_succeeded = false;
 static u64 mem_flags = EFI_MEMORY_WC | EFI_MEMORY_UC;
 
+static struct pci_dev *efifb_pci_dev;	/* dev with BAR covering the efifb */
+
 static struct fb_var_screeninfo efifb_defined = {
 	.activate		= FB_ACTIVATE_NOW,
 	.height			= -1,
@@ -241,18 +243,28 @@
 static inline void efifb_show_boot_graphics(struct fb_info *info) {}
 #endif
 
+/*
+ * fb_ops.fb_destroy is called by the last put_fb_info() call at the end
+ * of unregister_framebuffer() or fb_release(). Do any cleanup here.
+ */
 static void efifb_destroy(struct fb_info *info)
 {
+	if (efifb_pci_dev)
+		pm_runtime_put(&efifb_pci_dev->dev);
+
 	if (info->screen_base) {
 		if (mem_flags & (EFI_MEMORY_UC | EFI_MEMORY_WC))
 			iounmap(info->screen_base);
 		else
 			memunmap(info->screen_base);
 	}
+
 	if (request_mem_succeeded)
 		release_mem_region(info->apertures->ranges[0].base,
 				   info->apertures->ranges[0].size);
 	fb_dealloc_cmap(&info->cmap);
+
+	framebuffer_release(info);
 }
 
 static const struct fb_ops efifb_ops = {
@@ -333,7 +345,6 @@
 
 static bool pci_dev_disabled;	/* FB base matches BAR of a disabled device */
 
-static struct pci_dev *efifb_pci_dev;	/* dev with BAR covering the efifb */
 static struct resource *bar_resource;
 static u64 bar_offset;
 
@@ -347,6 +358,17 @@
 	char *option = NULL;
 	efi_memory_desc_t md;
 
+	/*
+	 * Generic drivers must not be registered if a framebuffer exists.
+	 * If a native driver was probed, the display hardware was already
+	 * taken and attempting to use the system framebuffer is dangerous.
+	 */
+	if (num_registered_fb > 0) {
+		dev_err(&dev->dev,
+			"efifb: a framebuffer is already registered\n");
+		return -EINVAL;
+	}
+
 	if (screen_info.orig_video_isVGA != VIDEO_TYPE_EFI || pci_dev_disabled)
 		return -ENODEV;
 
@@ -559,30 +581,28 @@
 		break;
 	}
 
-	err = sysfs_create_groups(&dev->dev.kobj, efifb_groups);
-	if (err) {
-		pr_err("efifb: cannot add sysfs attrs\n");
-		goto err_unmap;
-	}
 	err = fb_alloc_cmap(&info->cmap, 256, 0);
 	if (err < 0) {
 		pr_err("efifb: cannot allocate colormap\n");
-		goto err_groups;
+		goto err_unmap;
 	}
+
+	if (efifb_pci_dev)
+		WARN_ON(pm_runtime_get_sync(&efifb_pci_dev->dev) < 0);
+
 	err = register_framebuffer(info);
 	if (err < 0) {
 		pr_err("efifb: cannot register framebuffer\n");
-		goto err_fb_dealoc;
+		goto err_put_rpm_ref;
 	}
 	fb_info(info, "%s frame buffer device\n", info->fix.id);
-	if (efifb_pci_dev)
-		pm_runtime_get_sync(&efifb_pci_dev->dev);
 	return 0;
 
-err_fb_dealoc:
+err_put_rpm_ref:
+	if (efifb_pci_dev)
+		pm_runtime_put(&efifb_pci_dev->dev);
+
 	fb_dealloc_cmap(&info->cmap);
-err_groups:
-	sysfs_remove_groups(&dev->dev.kobj, efifb_groups);
 err_unmap:
 	if (mem_flags & (EFI_MEMORY_UC | EFI_MEMORY_WC))
 		iounmap(info->screen_base);
@@ -600,11 +620,8 @@
 {
 	struct fb_info *info = platform_get_drvdata(pdev);
 
+	/* efifb_destroy takes care of info cleanup */
 	unregister_framebuffer(info);
-	sysfs_remove_groups(&pdev->dev.kobj, efifb_groups);
-	framebuffer_release(info);
-	if (efifb_pci_dev)
-		pm_runtime_put(&efifb_pci_dev->dev);
 
 	return 0;
 }
@@ -612,6 +629,7 @@
 static struct platform_driver efifb_driver = {
 	.driver = {
 		.name = "efi-framebuffer",
+		.dev_groups = efifb_groups,
 	},
 	.probe = efifb_probe,
 	.remove = efifb_remove,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/ep93xx-fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/ep93xx-fb.c
@@ -474,7 +474,6 @@
 	if (!info)
 		return -ENOMEM;
 
-	info->dev = &pdev->dev;
 	platform_set_drvdata(pdev, info);
 	fbi = info->par;
 	fbi->mach_info = mach_info;
@@ -552,12 +551,14 @@
 
 	err = register_framebuffer(info);
 	if (err)
-		goto failed_check;
+		goto failed_framebuffer;
 
 	dev_info(info->dev, "registered. Mode = %dx%d-%d\n",
 		 info->var.xres, info->var.yres, info->var.bits_per_pixel);
 	return 0;
 
+failed_framebuffer:
+	clk_disable_unprepare(fbi->clk);
 failed_check:
 	if (fbi->mach_info->teardown)
 		fbi->mach_info->teardown(pdev);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/fsl-diu-fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/fsl-diu-fb.c
@@ -490,7 +490,7 @@
  * Workaround for failed writing desc register of planes.
  * Needed with MPC5121 DIU rev 2.0 silicon.
  */
-void wr_reg_wa(u32 *reg, u32 val)
+static void wr_reg_wa(u32 *reg, u32 val)
 {
 	do {
 		out_be32(reg, val);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/geode/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/geode/Kconfig
@@ -5,6 +5,7 @@
 config FB_GEODE
 	bool "AMD Geode family framebuffer support"
 	depends on FB && PCI && (X86_32 || (X86 && COMPILE_TEST))
+	depends on !UML
 	help
 	  Say 'Y' here to allow you to select framebuffer drivers for
 	  the AMD Geode family of processors.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/geode/lxfb_core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/geode/lxfb_core.c
@@ -234,6 +234,9 @@
 
 static int lxfb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
 {
+	if (!var->pixclock)
+		return -EINVAL;
+
 	if (var->xres > 1920 || var->yres > 1440)
 		return -EINVAL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/hecubafb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/hecubafb.c
@@ -115,8 +115,7 @@
 }
 
 /* this is called back from the deferred io workqueue */
-static void hecubafb_dpy_deferred_io(struct fb_info *info,
-				struct list_head *pagelist)
+static void hecubafb_dpy_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	hecubafb_dpy_update(info->par);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/hpfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/hpfb.c
@@ -344,6 +344,7 @@
 	if (hpfb_init_one(paddr, vaddr)) {
 		if (d->scode >= DIOII_SCBASE)
 			iounmap((void *)vaddr);
+		release_mem_region(d->resource.start, resource_size(&d->resource));
 		return -ENOMEM;
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/hyperv_fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/hyperv_fb.c
@@ -287,8 +287,6 @@
 
 static uint screen_width = HVFB_WIDTH;
 static uint screen_height = HVFB_HEIGHT;
-static uint screen_width_max = HVFB_WIDTH;
-static uint screen_height_max = HVFB_HEIGHT;
 static uint screen_depth;
 static uint screen_fb_size;
 static uint dio_fb_size; /* FB size for deferred IO */
@@ -422,11 +420,10 @@
 }
 
 /* Deferred IO callback */
-static void synthvid_deferred_io(struct fb_info *p,
-				 struct list_head *pagelist)
+static void synthvid_deferred_io(struct fb_info *p, struct list_head *pagereflist)
 {
 	struct hvfb_par *par = p->par;
-	struct page *page;
+	struct fb_deferred_io_pageref *pageref;
 	unsigned long start, end;
 	int y1, y2, miny, maxy;
 
@@ -439,7 +436,8 @@
 	 * in synthvid_update function by clamping the y2
 	 * value to yres.
 	 */
-	list_for_each_entry(page, pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *page = pageref->page;
 		start = page->index << PAGE_SHIFT;
 		end = start + PAGE_SIZE - 1;
 		y1 = start / p->fix.line_length;
@@ -582,7 +580,6 @@
 	int ret = 0;
 	unsigned long t;
 	u8 index;
-	int i;
 
 	memset(msg, 0, sizeof(struct synthvid_msg));
 	msg->vid_hdr.type = SYNTHVID_RESOLUTION_REQUEST;
@@ -613,13 +610,6 @@
 		goto out;
 	}
 
-	for (i = 0; i < msg->resolution_resp.resolution_count; i++) {
-		screen_width_max = max_t(unsigned int, screen_width_max,
-		    msg->resolution_resp.supported_resolution[i].width);
-		screen_height_max = max_t(unsigned int, screen_height_max,
-		    msg->resolution_resp.supported_resolution[i].height);
-	}
-
 	screen_width =
 		msg->resolution_resp.supported_resolution[index].width;
 	screen_height =
@@ -809,12 +799,18 @@
 static int hvfb_on_panic(struct notifier_block *nb,
 			 unsigned long e, void *p)
 {
+	struct hv_device *hdev;
 	struct hvfb_par *par;
 	struct fb_info *info;
 
 	par = container_of(nb, struct hvfb_par, hvfb_panic_nb);
-	par->synchronous_fb = true;
 	info = par->info;
+	hdev = device_to_hv_device(info->device);
+
+	if (hv_ringbuffer_spinlock_busy(hdev->channel))
+		return NOTIFY_DONE;
+
+	par->synchronous_fb = true;
 	if (par->need_docopy)
 		hvfb_docopy(par, 0, dio_fb_size);
 	synthvid_update(info, 0, 0, INT_MAX, INT_MAX);
@@ -941,7 +937,7 @@
 
 	if (x < HVFB_WIDTH_MIN || y < HVFB_HEIGHT_MIN ||
 	    (synthvid_ver_ge(par->synthvid_version, SYNTHVID_VERSION_WIN10) &&
-	    (x > screen_width_max || y > screen_height_max)) ||
+	    (x * y * screen_depth / 8 > screen_fb_size)) ||
 	    (par->synthvid_version == SYNTHVID_VERSION_WIN8 &&
 	     x * y * screen_depth / 8 > SYNTHVID_FB_SIZE_WIN8) ||
 	    (par->synthvid_version == SYNTHVID_VERSION_WIN7 &&
@@ -1019,7 +1015,6 @@
 	struct pci_dev *pdev  = NULL;
 	void __iomem *fb_virt;
 	int gen2vm = efi_enabled(EFI_BOOT);
-	resource_size_t pot_start, pot_end;
 	phys_addr_t paddr;
 	int ret;
 
@@ -1070,23 +1065,7 @@
 	dio_fb_size =
 		screen_width * screen_height * screen_depth / 8;
 
-	if (gen2vm) {
-		pot_start = 0;
-		pot_end = -1;
-	} else {
-		if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM) ||
-		    pci_resource_len(pdev, 0) < screen_fb_size) {
-			pr_err("Resource not available or (0x%lx < 0x%lx)\n",
-			       (unsigned long) pci_resource_len(pdev, 0),
-			       (unsigned long) screen_fb_size);
-			goto err1;
-		}
-
-		pot_end = pci_resource_end(pdev, 0);
-		pot_start = pot_end - screen_fb_size + 1;
-	}
-
-	ret = vmbus_allocate_mmio(&par->mem, hdev, pot_start, pot_end,
+	ret = vmbus_allocate_mmio(&par->mem, hdev, 0, -1,
 				  screen_fb_size, 0x100000, true);
 	if (ret != 0) {
 		pr_err("Unable to allocate framebuffer memory\n");
@@ -1151,7 +1130,7 @@
 
 	if (par->need_docopy) {
 		vfree(par->dio_vp);
-		iounmap(info->screen_base);
+		iounmap(par->mmio_vp);
 		vmbus_free_mmio(par->mem->start, screen_fb_size);
 	} else {
 		hvfb_release_phymem(hdev, info->fix.smem_start,
@@ -1194,8 +1173,8 @@
 	}
 
 	hvfb_get_option(info);
-	pr_info("Screen resolution: %dx%d, Color depth: %d\n",
-		screen_width, screen_height, screen_depth);
+	pr_info("Screen resolution: %dx%d, Color depth: %d, Frame buffer size: %d\n",
+		screen_width, screen_height, screen_depth, screen_fb_size);
 
 	ret = hvfb_getmem(hdev, info);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/i740fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/i740fb.c
@@ -400,7 +400,7 @@
 	u32 xres, right, hslen, left, xtotal;
 	u32 yres, lower, vslen, upper, ytotal;
 	u32 vxres, xoffset, vyres, yoffset;
-	u32 bpp, base, dacspeed24, mem;
+	u32 bpp, base, dacspeed24, mem, freq;
 	u8 r7;
 	int i;
 
@@ -643,7 +643,12 @@
 	par->atc[VGA_ATC_OVERSCAN] = 0;
 
 	/* Calculate VCLK that most closely matches the requested dot clock */
-	i740_calc_vclk((((u32)1e9) / var->pixclock) * (u32)(1e3), par);
+	freq = (((u32)1e9) / var->pixclock) * (u32)(1e3);
+	if (freq < I740_RFREQ_FIX) {
+		fb_dbg(info, "invalid pixclock\n");
+		freq = I740_RFREQ_FIX;
+	}
+	i740_calc_vclk(freq, par);
 
 	/* Since we program the clocks ourselves, always use VCLK2. */
 	par->misc |= 0x0C;
@@ -657,6 +662,9 @@
 
 static int i740fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
 {
+	if (!var->pixclock)
+		return -EINVAL;
+
 	switch (var->bits_per_pixel) {
 	case 8:
 		var->red.offset	= var->green.offset = var->blue.offset = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/imsttfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/imsttfb.c
@@ -1346,7 +1346,7 @@
 	.fb_ioctl 	= imsttfb_ioctl,
 };
 
-static void init_imstt(struct fb_info *info)
+static int init_imstt(struct fb_info *info)
 {
 	struct imstt_par *par = info->par;
 	__u32 i, tmp, *ip, *end;
@@ -1419,7 +1419,7 @@
 	    || !(compute_imstt_regvals(par, info->var.xres, info->var.yres))) {
 		printk("imsttfb: %ux%ux%u not supported\n", info->var.xres, info->var.yres, info->var.bits_per_pixel);
 		framebuffer_release(info);
-		return;
+		return -ENODEV;
 	}
 
 	sprintf(info->fix.id, "IMS TT (%s)", par->ramdac == IBM ? "IBM" : "TVP");
@@ -1455,12 +1455,13 @@
 
 	if (register_framebuffer(info) < 0) {
 		framebuffer_release(info);
-		return;
+		return -ENODEV;
 	}
 
 	tmp = (read_reg_le32(par->dc_regs, SSTATUS) & 0x0f00) >> 8;
 	fb_info(info, "%s frame buffer; %uMB vram; chip version %u\n",
 		info->fix.id, info->fix.smem_len >> 20, tmp);
+	return 0;
 }
 
 static int imsttfb_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
@@ -1488,8 +1489,8 @@
 
 	if (!request_mem_region(addr, size, "imsttfb")) {
 		printk(KERN_ERR "imsttfb: Can't reserve memory region\n");
-		framebuffer_release(info);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto release_info;
 	}
 
 	switch (pdev->device) {
@@ -1506,34 +1507,39 @@
 			printk(KERN_INFO "imsttfb: Device 0x%x unknown, "
 					 "contact maintainer.\n", pdev->device);
 			ret = -ENODEV;
-			goto error;
+			goto release_mem_region;
 	}
 
 	info->fix.smem_start = addr;
 	info->screen_base = (__u8 *)ioremap(addr, par->ramdac == IBM ?
 					    0x400000 : 0x800000);
 	if (!info->screen_base)
-		goto error;
+		goto release_mem_region;
 	info->fix.mmio_start = addr + 0x800000;
 	par->dc_regs = ioremap(addr + 0x800000, 0x1000);
 	if (!par->dc_regs)
-		goto error;
+		goto unmap_screen_base;
 	par->cmap_regs_phys = addr + 0x840000;
 	par->cmap_regs = (__u8 *)ioremap(addr + 0x840000, 0x1000);
 	if (!par->cmap_regs)
-		goto error;
+		goto unmap_dc_regs;
 	info->pseudo_palette = par->palette;
-	init_imstt(info);
+	ret = init_imstt(info);
+	if (ret)
+		goto unmap_cmap_regs;
 
 	pci_set_drvdata(pdev, info);
 	return 0;
 
-error:
-	if (par->dc_regs)
-		iounmap(par->dc_regs);
-	if (info->screen_base)
-		iounmap(info->screen_base);
+unmap_cmap_regs:
+	iounmap(par->cmap_regs);
+unmap_dc_regs:
+	iounmap(par->dc_regs);
+unmap_screen_base:
+	iounmap(info->screen_base);
+release_mem_region:
 	release_mem_region(addr, size);
+release_info:
 	framebuffer_release(info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/imxfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/imxfb.c
@@ -602,10 +602,10 @@
 	if (var->hsync_len < 1    || var->hsync_len > 64)
 		printk(KERN_ERR "%s: invalid hsync_len %d\n",
 			info->fix.id, var->hsync_len);
-	if (var->left_margin > 255)
+	if (var->left_margin < 3  || var->left_margin > 255)
 		printk(KERN_ERR "%s: invalid left_margin %d\n",
 			info->fix.id, var->left_margin);
-	if (var->right_margin > 255)
+	if (var->right_margin < 1 || var->right_margin > 255)
 		printk(KERN_ERR "%s: invalid right_margin %d\n",
 			info->fix.id, var->right_margin);
 	if (var->yres < 1 || var->yres > ymax_mask)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/intelfb/intelfbdrv.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/intelfb/intelfbdrv.c
@@ -1214,6 +1214,9 @@
 
 	dinfo = GET_DINFO(info);
 
+	if (!var->pixclock)
+		return -EINVAL;
+
 	/* update the pitch */
 	if (intelfbhw_validate_mode(dinfo, var) != 0)
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/matrox/matroxfb_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/matrox/matroxfb_base.c
@@ -1377,8 +1377,8 @@
 	.lowlevel = &matrox_G100
 };
 static struct video_board vbG200eW = {
-	.maxvram = 0x800000,
-	.maxdisplayable = 0x800000,
+	.maxvram = 0x1000000,
+	.maxdisplayable = 0x0800000,
 	.accelID = FB_ACCEL_MATROX_MGAG200,
 	.lowlevel = &matrox_G100
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/metronomefb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/metronomefb.c
@@ -465,16 +465,15 @@
 }
 
 /* this is called back from the deferred io workqueue */
-static void metronomefb_dpy_deferred_io(struct fb_info *info,
-				struct list_head *pagelist)
+static void metronomefb_dpy_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	u16 cksum;
-	struct page *cur;
-	struct fb_deferred_io *fbdefio = info->fbdefio;
+	struct fb_deferred_io_pageref *pageref;
 	struct metronomefb_par *par = info->par;
 
 	/* walk the written page list and swizzle the data */
-	list_for_each_entry(cur, &fbdefio->pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *cur = pageref->page;
 		cksum = metronomefb_dpy_update_page(par,
 					(cur->index << PAGE_SHIFT));
 		par->metromem_img_csum -= par->csum_table[cur->index];
@@ -567,8 +566,9 @@
 };
 
 static struct fb_deferred_io metronomefb_defio = {
-	.delay		= HZ,
-	.deferred_io	= metronomefb_dpy_deferred_io,
+	.delay			= HZ,
+	.sort_pagereflist	= true,
+	.deferred_io		= metronomefb_dpy_deferred_io,
 };
 
 static int metronomefb_probe(struct platform_device *dev)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/mmp/hw/mmp_ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/mmp/hw/mmp_ctrl.c
@@ -518,7 +518,9 @@
 		ret = -ENOENT;
 		goto failed;
 	}
-	clk_prepare_enable(ctrl->clk);
+	ret = clk_prepare_enable(ctrl->clk);
+	if (ret)
+		goto failed;
 
 	/* init global regs */
 	ctrl_set_default(ctrl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/nvidia/nv_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/nvidia/nv_i2c.c
@@ -86,7 +86,7 @@
 {
 	int rc;
 
-	strcpy(chan->adapter.name, name);
+	strscpy(chan->adapter.name, name, sizeof(chan->adapter.name));
 	chan->adapter.owner = THIS_MODULE;
 	chan->adapter.class = i2c_class;
 	chan->adapter.algo_data = &chan->algo;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/nvidia/nvidia.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/nvidia/nvidia.c
@@ -763,6 +763,8 @@
 	int pitch, err = 0;
 
 	NVTRACE_ENTER();
+	if (!var->pixclock)
+		return -EINVAL;
 
 	var->transp.offset = 0;
 	var->transp.length = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap/lcd_mipid.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap/lcd_mipid.c
@@ -563,11 +563,15 @@
 
 	r = mipid_detect(md);
 	if (r < 0)
-		return r;
+		goto free_md;
 
 	omapfb_register_panel(&md->panel);
 
 	return 0;
+
+free_md:
+	kfree(md);
+	return r;
 }
 
 static int mipid_spi_remove(struct spi_device *spi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap2/omapfb/displays/connector-dvi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap2/omapfb/displays/connector-dvi.c
@@ -246,6 +246,7 @@
 	adapter_node = of_parse_phandle(node, "ddc-i2c-bus", 0);
 	if (adapter_node) {
 		adapter = of_get_i2c_adapter_by_node(adapter_node);
+		of_node_put(adapter_node);
 		if (adapter == NULL) {
 			dev_err(&pdev->dev, "failed to parse ddc-i2c-bus\n");
 			omap_dss_put_device(ddata->in);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap2/omapfb/displays/panel-dsi-cm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap2/omapfb/displays/panel-dsi-cm.c
@@ -409,7 +409,7 @@
 	if (r)
 		return r;
 
-	return snprintf(buf, PAGE_SIZE, "%d\n", errors);
+	return sysfs_emit(buf, "%d\n", errors);
 }
 
 static ssize_t dsicm_hw_revision_show(struct device *dev,
@@ -439,7 +439,7 @@
 	if (r)
 		return r;
 
-	return snprintf(buf, PAGE_SIZE, "%02x.%02x.%02x\n", id1, id2, id3);
+	return sysfs_emit(buf, "%02x.%02x.%02x\n", id1, id2, id3);
 }
 
 static ssize_t dsicm_store_ulps(struct device *dev,
@@ -487,7 +487,7 @@
 	t = ddata->ulps_enabled;
 	mutex_unlock(&ddata->lock);
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", t);
+	return sysfs_emit(buf, "%u\n", t);
 }
 
 static ssize_t dsicm_store_ulps_timeout(struct device *dev,
@@ -532,7 +532,7 @@
 	t = ddata->ulps_timeout;
 	mutex_unlock(&ddata->lock);
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", t);
+	return sysfs_emit(buf, "%u\n", t);
 }
 
 static DEVICE_ATTR(num_dsi_errors, S_IRUGO, dsicm_num_errors_show, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap2/omapfb/displays/panel-sony-acx565akm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap2/omapfb/displays/panel-sony-acx565akm.c
@@ -476,7 +476,7 @@
 	int i;
 
 	if (!ddata->has_cabc)
-		return snprintf(buf, PAGE_SIZE, "%s\n", cabc_modes[0]);
+		return sysfs_emit(buf, "%s\n", cabc_modes[0]);
 
 	for (i = 0, len = 0;
 	     len < PAGE_SIZE && i < ARRAY_SIZE(cabc_modes); i++)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap2/omapfb/displays/panel-tpo-td043mtea1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap2/omapfb/displays/panel-tpo-td043mtea1.c
@@ -169,7 +169,7 @@
 {
 	struct panel_drv_data *ddata = dev_get_drvdata(dev);
 
-	return snprintf(buf, PAGE_SIZE, "%d\n", ddata->vmirror);
+	return sysfs_emit(buf, "%d\n", ddata->vmirror);
 }
 
 static ssize_t tpo_td043_vmirror_store(struct device *dev,
@@ -199,7 +199,7 @@
 {
 	struct panel_drv_data *ddata = dev_get_drvdata(dev);
 
-	return snprintf(buf, PAGE_SIZE, "%d\n", ddata->mode);
+	return sysfs_emit(buf, "%d\n", ddata->mode);
 }
 
 static ssize_t tpo_td043_mode_store(struct device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap2/omapfb/dss/dsi.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap2/omapfb/dss/dsi.c
@@ -1538,22 +1538,28 @@
 {
 	struct dsi_data *dsi = dsi_get_dsidrv_data(dsidev);
 	unsigned long flags;
-	struct dsi_irq_stats stats;
+	struct dsi_irq_stats *stats;
+
+	stats = kzalloc(sizeof(*stats), GFP_KERNEL);
+	if (!stats) {
+		seq_printf(s, "out of memory\n");
+		return;
+	}
 
 	spin_lock_irqsave(&dsi->irq_stats_lock, flags);
 
-	stats = dsi->irq_stats;
+	*stats = dsi->irq_stats;
 	memset(&dsi->irq_stats, 0, sizeof(dsi->irq_stats));
 	dsi->irq_stats.last_reset = jiffies;
 
 	spin_unlock_irqrestore(&dsi->irq_stats_lock, flags);
 
 	seq_printf(s, "period %u ms\n",
-			jiffies_to_msecs(jiffies - stats.last_reset));
+			jiffies_to_msecs(jiffies - stats->last_reset));
 
-	seq_printf(s, "irqs %d\n", stats.irq_count);
+	seq_printf(s, "irqs %d\n", stats->irq_count);
 #define PIS(x) \
-	seq_printf(s, "%-20s %10d\n", #x, stats.dsi_irqs[ffs(DSI_IRQ_##x)-1])
+	seq_printf(s, "%-20s %10d\n", #x, stats->dsi_irqs[ffs(DSI_IRQ_##x)-1])
 
 	seq_printf(s, "-- DSI%d interrupts --\n", dsi->module_id + 1);
 	PIS(VC0);
@@ -1577,10 +1583,10 @@
 
 #define PIS(x) \
 	seq_printf(s, "%-20s %10d %10d %10d %10d\n", #x, \
-			stats.vc_irqs[0][ffs(DSI_VC_IRQ_##x)-1], \
-			stats.vc_irqs[1][ffs(DSI_VC_IRQ_##x)-1], \
-			stats.vc_irqs[2][ffs(DSI_VC_IRQ_##x)-1], \
-			stats.vc_irqs[3][ffs(DSI_VC_IRQ_##x)-1]);
+			stats->vc_irqs[0][ffs(DSI_VC_IRQ_##x)-1], \
+			stats->vc_irqs[1][ffs(DSI_VC_IRQ_##x)-1], \
+			stats->vc_irqs[2][ffs(DSI_VC_IRQ_##x)-1], \
+			stats->vc_irqs[3][ffs(DSI_VC_IRQ_##x)-1]);
 
 	seq_printf(s, "-- VC interrupts --\n");
 	PIS(CS);
@@ -1596,7 +1602,7 @@
 
 #define PIS(x) \
 	seq_printf(s, "%-20s %10d\n", #x, \
-			stats.cio_irqs[ffs(DSI_CIO_IRQ_##x)-1]);
+			stats->cio_irqs[ffs(DSI_CIO_IRQ_##x)-1]);
 
 	seq_printf(s, "-- CIO interrupts --\n");
 	PIS(ERRSYNCESC1);
@@ -1620,6 +1626,8 @@
 	PIS(ULPSACTIVENOT_ALL0);
 	PIS(ULPSACTIVENOT_ALL1);
 #undef PIS
+
+	kfree(stats);
 }
 
 static void dsi1_dump_irqs(struct seq_file *s)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/omap2/omapfb/dss/dss-of.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/omap2/omapfb/dss/dss-of.c
@@ -102,6 +102,7 @@
 		np = of_get_next_parent(np);
 	}
 
+	of_node_put(np);
 	return NULL;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/pm2fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/pm2fb.c
@@ -617,6 +617,11 @@
 		return -EINVAL;
 	}
 
+	if (!var->pixclock) {
+		DPRINTK("pixclock is zero\n");
+		return -EINVAL;
+	}
+
 	if (PICOS2KHZ(var->pixclock) > PM2_MAX_PIXCLOCK) {
 		DPRINTK("pixclock too high (%ldKHz)\n",
 			PICOS2KHZ(var->pixclock));
@@ -1525,8 +1530,10 @@
 	}
 
 	info = framebuffer_alloc(sizeof(struct pm2fb_par), &pdev->dev);
-	if (!info)
-		return -ENOMEM;
+	if (!info) {
+		err = -ENOMEM;
+		goto err_exit_disable;
+	}
 	default_par = info->par;
 
 	switch (pdev->device) {
@@ -1707,6 +1714,8 @@
 	release_mem_region(pm2fb_fix.mmio_start, pm2fb_fix.mmio_len);
  err_exit_neither:
 	framebuffer_release(info);
+ err_exit_disable:
+	pci_disable_device(pdev);
 	return retval;
 }
 
@@ -1733,6 +1742,7 @@
 	fb_dealloc_cmap(&info->cmap);
 	kfree(info->pixmap.addr);
 	framebuffer_release(info);
+	pci_disable_device(pdev);
 }
 
 static const struct pci_device_id pm2fb_id_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/pxa3xx-gcu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/pxa3xx-gcu.c
@@ -381,7 +381,7 @@
 	struct pxa3xx_gcu_batch	*buffer;
 	struct pxa3xx_gcu_priv *priv = to_pxa3xx_gcu_priv(file);
 
-	int words = count / 4;
+	size_t words = count / 4;
 
 	/* Does not need to be atomic. There's a lock in user space,
 	 * but anyhow, this is just for statistics. */
@@ -650,6 +650,7 @@
 	for (i = 0; i < 8; i++) {
 		ret = pxa3xx_gcu_add_buffer(dev, priv);
 		if (ret) {
+			pxa3xx_gcu_free_buffers(dev, priv);
 			dev_err(dev, "failed to allocate DMA memory\n");
 			goto err_disable_clk;
 		}
@@ -666,15 +667,15 @@
 			SHARED_SIZE, irq);
 	return 0;
 
-err_free_dma:
-	dma_free_coherent(dev, SHARED_SIZE,
-			priv->shared, priv->shared_phys);
+err_disable_clk:
+	clk_disable_unprepare(priv->clk);
 
 err_misc_deregister:
 	misc_deregister(&priv->misc_dev);
 
-err_disable_clk:
-	clk_disable_unprepare(priv->clk);
+err_free_dma:
+	dma_free_coherent(dev, SHARED_SIZE,
+			  priv->shared, priv->shared_phys);
 
 	return ret;
 }
@@ -687,6 +688,7 @@
 	pxa3xx_gcu_wait_idle(priv);
 	misc_deregister(&priv->misc_dev);
 	dma_free_coherent(dev, SHARED_SIZE, priv->shared, priv->shared_phys);
+	clk_disable_unprepare(priv->clk);
 	pxa3xx_gcu_free_buffers(dev, priv);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/pxafb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/pxafb.c
@@ -2408,6 +2408,7 @@
 	info = &fbi->fb;
 
 	pxafb_overlay_exit(fbi);
+	cancel_work_sync(&fbi->task);
 	unregister_framebuffer(info);
 
 	pxafb_disable_controller(fbi);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/s3fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/s3fb.c
@@ -902,6 +902,8 @@
 	value = clamp((htotal + hsstart + 1) / 2 + 2, hsstart + 4, htotal + 1);
 	svga_wcrt_multi(par->state.vgabase, s3_dtpc_regs, value);
 
+	if (screen_size > info->screen_size)
+		screen_size = info->screen_size;
 	memset_io(info->screen_base, 0x00, screen_size);
 	/* Device and screen back on */
 	svga_wcrt_mask(par->state.vgabase, 0x17, 0x80, 0x80);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/savage/savagefb_driver.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/savage/savagefb_driver.c
@@ -868,6 +868,9 @@
 
 	DBG("savagefb_check_var");
 
+	if (!var->pixclock)
+		return -EINVAL;
+
 	var->transp.offset = 0;
 	var->transp.length = 0;
 	switch (var->bits_per_pixel) {
@@ -2268,7 +2271,10 @@
 	if (info->var.xres_virtual > 0x1000)
 		info->var.xres_virtual = 0x1000;
 #endif
-	savagefb_check_var(&info->var, info);
+	err = savagefb_check_var(&info->var, info);
+	if (err)
+		goto failed;
+
 	savagefb_set_fix(info);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sh7760fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sh7760fb.c
@@ -359,7 +359,7 @@
 	if (!info->screen_base)
 		return;
 
-	dma_free_coherent(info->dev, info->screen_size,
+	dma_free_coherent(info->device, info->screen_size,
 			  info->screen_base, par->fbdma);
 
 	par->fbdma = 0;
@@ -408,14 +408,13 @@
 	if (vram < PAGE_SIZE)
 		vram = PAGE_SIZE;
 
-	fbmem = dma_alloc_coherent(info->dev, vram, &par->fbdma, GFP_KERNEL);
-
+	fbmem = dma_alloc_coherent(info->device, vram, &par->fbdma, GFP_KERNEL);
 	if (!fbmem)
 		return -ENOMEM;
 
 	if ((par->fbdma & SH7760FB_DMA_MASK) != SH7760FB_DMA_MASK) {
-		sh7760fb_free_mem(info);
-		dev_err(info->dev, "kernel gave me memory at 0x%08lx, which is"
+		dma_free_coherent(info->device, vram, fbmem, par->fbdma);
+		dev_err(info->device, "kernel gave me memory at 0x%08lx, which is"
 			"unusable for the LCDC\n", (unsigned long)par->fbdma);
 		return -ENOMEM;
 	}
@@ -486,7 +485,7 @@
 
 	ret = sh7760fb_alloc_mem(info);
 	if (ret) {
-		dev_dbg(info->dev, "framebuffer memory allocation failed!\n");
+		dev_dbg(info->device, "framebuffer memory allocation failed!\n");
 		goto out_unmap;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sh_mobile_lcdcfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sh_mobile_lcdcfb.c
@@ -435,24 +435,24 @@
 	.read_data	= lcdc_sys_read_data,
 };
 
-static int sh_mobile_lcdc_sginit(struct fb_info *info,
-				  struct list_head *pagelist)
+static int sh_mobile_lcdc_sginit(struct fb_info *info, struct list_head *pagereflist)
 {
 	struct sh_mobile_lcdc_chan *ch = info->par;
 	unsigned int nr_pages_max = ch->fb_size >> PAGE_SHIFT;
-	struct page *page;
+	struct fb_deferred_io_pageref *pageref;
 	int nr_pages = 0;
 
 	sg_init_table(ch->sglist, nr_pages_max);
 
-	list_for_each_entry(page, pagelist, lru)
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *page = pageref->page;
 		sg_set_page(&ch->sglist[nr_pages++], page, PAGE_SIZE, 0);
+	}
 
 	return nr_pages;
 }
 
-static void sh_mobile_lcdc_deferred_io(struct fb_info *info,
-				       struct list_head *pagelist)
+static void sh_mobile_lcdc_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	struct sh_mobile_lcdc_chan *ch = info->par;
 	const struct sh_mobile_lcdc_panel_cfg *panel = &ch->cfg->panel_cfg;
@@ -461,7 +461,7 @@
 	sh_mobile_lcdc_clk_on(ch->lcdc);
 
 	/*
-	 * It's possible to get here without anything on the pagelist via
+	 * It's possible to get here without anything on the pagereflist via
 	 * sh_mobile_lcdc_deferred_io_touch() or via a userspace fsync()
 	 * invocation. In the former case, the acceleration routines are
 	 * stepped in to when using the framebuffer console causing the
@@ -471,12 +471,12 @@
 	 * acceleration routines have their own methods for writing in
 	 * that still need to be updated.
 	 *
-	 * The fsync() and empty pagelist case could be optimized for,
+	 * The fsync() and empty pagereflist case could be optimized for,
 	 * but we don't bother, as any application exhibiting such
 	 * behaviour is fundamentally broken anyways.
 	 */
-	if (!list_empty(pagelist)) {
-		unsigned int nr_pages = sh_mobile_lcdc_sginit(info, pagelist);
+	if (!list_empty(pagereflist)) {
+		unsigned int nr_pages = sh_mobile_lcdc_sginit(info, pagereflist);
 
 		/* trigger panel update */
 		dma_map_sg(ch->lcdc->dev, ch->sglist, nr_pages, DMA_TO_DEVICE);
@@ -1577,7 +1577,7 @@
 	 */
 	info->fix = sh_mobile_lcdc_overlay_fix;
 	snprintf(info->fix.id, sizeof(info->fix.id),
-		 "SH Mobile LCDC Overlay %u", ovl->index);
+		 "SHMobile ovl %u", ovl->index);
 	info->fix.smem_start = ovl->dma_handle;
 	info->fix.smem_len = ovl->fb_size;
 	info->fix.line_length = ovl->pitch;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/simplefb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/simplefb.c
@@ -70,12 +70,18 @@
 static void simplefb_clocks_destroy(struct simplefb_par *par);
 static void simplefb_regulators_destroy(struct simplefb_par *par);
 
+/*
+ * fb_ops.fb_destroy is called by the last put_fb_info() call at the end
+ * of unregister_framebuffer() or fb_release(). Do any cleanup here.
+ */
 static void simplefb_destroy(struct fb_info *info)
 {
 	simplefb_regulators_destroy(info->par);
 	simplefb_clocks_destroy(info->par);
 	if (info->screen_base)
 		iounmap(info->screen_base);
+
+	framebuffer_release(info);
 }
 
 static const struct fb_ops simplefb_ops = {
@@ -407,6 +413,17 @@
 	struct simplefb_par *par;
 	struct resource *mem;
 
+	/*
+	 * Generic drivers must not be registered if a framebuffer exists.
+	 * If a native driver was probed, the display hardware was already
+	 * taken and attempting to use the system framebuffer is dangerous.
+	 */
+	if (num_registered_fb > 0) {
+		dev_err(&pdev->dev,
+			"simplefb: a framebuffer is already registered\n");
+		return -EINVAL;
+	}
+
 	if (fb_get_options("simplefb", NULL))
 		return -ENODEV;
 
@@ -509,8 +526,8 @@
 {
 	struct fb_info *info = platform_get_drvdata(pdev);
 
+	/* simplefb_destroy takes care of info cleanup */
 	unregister_framebuffer(info);
-	framebuffer_release(info);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sis/init.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sis/init.c
@@ -355,12 +355,12 @@
 		}
 		break;
 	case 400:
-		if((!(VBFlags & CRT1_LCDA)) || ((LCDwidth >= 800) && (LCDwidth >= 600))) {
+		if((!(VBFlags & CRT1_LCDA)) || ((LCDwidth >= 800) && (LCDheight >= 600))) {
 			if(VDisplay == 300) ModeIndex = ModeIndex_400x300[Depth];
 		}
 		break;
 	case 512:
-		if((!(VBFlags & CRT1_LCDA)) || ((LCDwidth >= 1024) && (LCDwidth >= 768))) {
+		if((!(VBFlags & CRT1_LCDA)) || ((LCDwidth >= 1024) && (LCDheight >= 768))) {
 			if(VDisplay == 384) ModeIndex = ModeIndex_512x384[Depth];
 		}
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sis/init301.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sis/init301.c
@@ -172,7 +172,7 @@
 };
 
 /* 301C / 302ELV extended Part2 TV registers (4 tap scaler) */
-
+#ifdef CONFIG_FB_SIS_315
 static const unsigned char SiS_Part2CLVX_1[] = {
     0x00,0x00,
     0x00,0x20,0x00,0x00,0x7F,0x20,0x02,0x7F,0x7D,0x20,0x04,0x7F,0x7D,0x1F,0x06,0x7E,
@@ -245,7 +245,6 @@
     0xFF,0xFF,
 };
 
-#ifdef CONFIG_FB_SIS_315
 /* 661 et al LCD data structure (2.03.00) */
 static const unsigned char SiS_LCDStruct661[] = {
     /* 1024x768 */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sis/sis_main.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sis/sis_main.c
@@ -183,7 +183,7 @@
 {
 	unsigned int j = 0, xres = 0, yres = 0, depth = 0, rate = 0;
 	int i = 0;
-	char strbuf[16], strbuf1[20];
+	char strbuf[24], strbuf1[20];
 	char *nameptr = name;
 
 	/* We don't know the hardware specs yet and there is no ivideo */
@@ -1474,6 +1474,8 @@
 
 	vtotal = var->upper_margin + var->lower_margin + var->vsync_len;
 
+	if (!var->pixclock)
+		return -EINVAL;
 	pixclock = var->pixclock;
 
 	if((var->vmode & FB_VMODE_MASK) == FB_VMODE_NONINTERLACED) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sm501fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sm501fb.c
@@ -326,6 +326,13 @@
 	if (var->xres_virtual > 4096 || var->yres_virtual > 2048)
 		return -EINVAL;
 
+	/* geometry sanity checks */
+	if (var->xres + var->xoffset > var->xres_virtual)
+		return -EINVAL;
+
+	if (var->yres + var->yoffset > var->yres_virtual)
+		return -EINVAL;
+
 	/* can cope with 8,16 or 32bpp */
 
 	if (var->bits_per_pixel <= 8)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sm712fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sm712fb.c
@@ -1047,7 +1047,7 @@
 	if (count + p > total_size)
 		count = total_size - p;
 
-	buffer = kmalloc((count > PAGE_SIZE) ? PAGE_SIZE : count, GFP_KERNEL);
+	buffer = kmalloc(PAGE_SIZE, GFP_KERNEL);
 	if (!buffer)
 		return -ENOMEM;
 
@@ -1059,25 +1059,14 @@
 	while (count) {
 		c = (count > PAGE_SIZE) ? PAGE_SIZE : count;
 		dst = buffer;
-		for (i = c >> 2; i--;) {
-			*dst = fb_readl(src++);
-			*dst = big_swap(*dst);
+		for (i = (c + 3) >> 2; i--;) {
+			u32 val;
+
+			val = fb_readl(src);
+			*dst = big_swap(val);
+			src++;
 			dst++;
 		}
-		if (c & 3) {
-			u8 *dst8 = (u8 *)dst;
-			u8 __iomem *src8 = (u8 __iomem *)src;
-
-			for (i = c & 3; i--;) {
-				if (i & 1) {
-					*dst8++ = fb_readb(++src8);
-				} else {
-					*dst8++ = fb_readb(--src8);
-					src8 += 2;
-				}
-			}
-			src = (u32 __iomem *)src8;
-		}
 
 		if (copy_to_user(buf, buffer, c)) {
 			err = -EFAULT;
@@ -1130,7 +1119,7 @@
 		count = total_size - p;
 	}
 
-	buffer = kmalloc((count > PAGE_SIZE) ? PAGE_SIZE : count, GFP_KERNEL);
+	buffer = kmalloc(PAGE_SIZE, GFP_KERNEL);
 	if (!buffer)
 		return -ENOMEM;
 
@@ -1148,24 +1137,11 @@
 			break;
 		}
 
-		for (i = c >> 2; i--;) {
-			fb_writel(big_swap(*src), dst++);
+		for (i = (c + 3) >> 2; i--;) {
+			fb_writel(big_swap(*src), dst);
+			dst++;
 			src++;
 		}
-		if (c & 3) {
-			u8 *src8 = (u8 *)src;
-			u8 __iomem *dst8 = (u8 __iomem *)dst;
-
-			for (i = c & 3; i--;) {
-				if (i & 1) {
-					fb_writeb(*src8++, ++dst8);
-				} else {
-					fb_writeb(*src8++, --dst8);
-					dst8 += 2;
-				}
-			}
-			dst = (u32 __iomem *)dst8;
-		}
 
 		*ppos += c;
 		buf += c;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/smscufx.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/smscufx.c
@@ -97,7 +97,6 @@
 	struct kref kref;
 	int fb_count;
 	bool virtualized; /* true when physical usb device not present */
-	struct delayed_work free_framebuffer_work;
 	atomic_t usb_active; /* 0 = update virtual buffer, but no usb traffic */
 	atomic_t lost_pixels; /* 1 = a render op failed. Need screen refresh */
 	u8 *edid; /* null until we read edid from hw or get from sysfs */
@@ -137,6 +136,8 @@
 static int ufx_alloc_urb_list(struct ufx_data *dev, int count, size_t size);
 static void ufx_free_urb_list(struct ufx_data *dev);
 
+static DEFINE_MUTEX(disconnect_mutex);
+
 /* reads a control register */
 static int ufx_reg_read(struct ufx_data *dev, u32 index, u32 *data)
 {
@@ -952,12 +953,10 @@
  *   Touching ANY framebuffer memory that triggers a page fault
  *   in fb_defio will cause a deadlock, when it also tries to
  *   grab the same mutex. */
-static void ufx_dpy_deferred_io(struct fb_info *info,
-				struct list_head *pagelist)
+static void ufx_dpy_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
-	struct page *cur;
-	struct fb_deferred_io *fbdefio = info->fbdefio;
 	struct ufx_data *dev = info->par;
+	struct fb_deferred_io_pageref *pageref;
 
 	if (!fb_defio)
 		return;
@@ -966,9 +965,10 @@
 		return;
 
 	/* walk the written page list and render each to device */
-	list_for_each_entry(cur, &fbdefio->pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
 		/* create a rectangle of full screen width that encloses the
 		 * entire dirty framebuffer page */
+		struct page *cur = pageref->page;
 		const int x = 0;
 		const int width = dev->info->var.xres;
 		const int y = (cur->index << PAGE_SHIFT) / (width * 2);
@@ -1070,9 +1070,13 @@
 	if (user == 0 && !console)
 		return -EBUSY;
 
+	mutex_lock(&disconnect_mutex);
+
 	/* If the USB device is gone, we don't accept new opens */
-	if (dev->virtualized)
+	if (dev->virtualized) {
+		mutex_unlock(&disconnect_mutex);
 		return -ENODEV;
+	}
 
 	dev->fb_count++;
 
@@ -1096,6 +1100,8 @@
 	pr_debug("open /dev/fb%d user=%d fb_info=%p count=%d",
 		info->node, user, info, dev->fb_count);
 
+	mutex_unlock(&disconnect_mutex);
+
 	return 0;
 }
 
@@ -1108,15 +1114,24 @@
 {
 	struct ufx_data *dev = container_of(kref, struct ufx_data, kref);
 
-	/* this function will wait for all in-flight urbs to complete */
-	if (dev->urbs.count > 0)
-		ufx_free_urb_list(dev);
+	kfree(dev);
+}
 
-	pr_debug("freeing ufx_data %p", dev);
+static void ufx_ops_destory(struct fb_info *info)
+{
+	struct ufx_data *dev = info->par;
+	int node = info->node;
 
-	kfree(dev);
+	/* Assume info structure is freed after this point */
+	framebuffer_release(info);
+
+	pr_debug("fb_info for /dev/fb%d has been freed", node);
+
+	/* release reference taken by kref_init in probe() */
+	kref_put(&dev->kref, ufx_free);
 }
 
+
 static void ufx_release_urb_work(struct work_struct *work)
 {
 	struct urb_node *unode = container_of(work, struct urb_node,
@@ -1125,14 +1140,9 @@
 	up(&unode->dev->urbs.limit_sem);
 }
 
-static void ufx_free_framebuffer_work(struct work_struct *work)
+static void ufx_free_framebuffer(struct ufx_data *dev)
 {
-	struct ufx_data *dev = container_of(work, struct ufx_data,
-					    free_framebuffer_work.work);
 	struct fb_info *info = dev->info;
-	int node = info->node;
-
-	unregister_framebuffer(info);
 
 	if (info->cmap.len != 0)
 		fb_dealloc_cmap(&info->cmap);
@@ -1144,11 +1154,6 @@
 
 	dev->info = NULL;
 
-	/* Assume info structure is freed after this point */
-	framebuffer_release(info);
-
-	pr_debug("fb_info for /dev/fb%d has been freed", node);
-
 	/* ref taken in probe() as part of registering framebfufer */
 	kref_put(&dev->kref, ufx_free);
 }
@@ -1160,11 +1165,13 @@
 {
 	struct ufx_data *dev = info->par;
 
+	mutex_lock(&disconnect_mutex);
+
 	dev->fb_count--;
 
 	/* We can't free fb_info here - fbmem will touch it when we return */
 	if (dev->virtualized && (dev->fb_count == 0))
-		schedule_delayed_work(&dev->free_framebuffer_work, HZ);
+		ufx_free_framebuffer(dev);
 
 	if ((dev->fb_count == 0) && (info->fbdefio)) {
 		fb_deferred_io_cleanup(info);
@@ -1177,6 +1184,8 @@
 
 	kref_put(&dev->kref, ufx_free);
 
+	mutex_unlock(&disconnect_mutex);
+
 	return 0;
 }
 
@@ -1283,6 +1292,7 @@
 	.fb_blank = ufx_ops_blank,
 	.fb_check_var = ufx_ops_check_var,
 	.fb_set_par = ufx_ops_set_par,
+	.fb_destroy = ufx_ops_destory,
 };
 
 /* Assumes &info->lock held by caller
@@ -1610,7 +1620,7 @@
 	struct usb_device *usbdev;
 	struct ufx_data *dev;
 	struct fb_info *info;
-	int retval;
+	int retval = -ENOMEM;
 	u32 id_rev, fpga_rev;
 
 	/* usb initialization */
@@ -1642,20 +1652,23 @@
 
 	if (!ufx_alloc_urb_list(dev, WRITES_IN_FLIGHT, MAX_TRANSFER)) {
 		dev_err(dev->gdev, "ufx_alloc_urb_list failed\n");
-		goto e_nomem;
+		goto put_ref;
 	}
 
 	/* We don't register a new USB class. Our client interface is fbdev */
 
 	/* allocates framebuffer driver structure, not framebuffer memory */
 	info = framebuffer_alloc(0, &usbdev->dev);
-	if (!info)
-		goto e_nomem;
+	if (!info) {
+		dev_err(dev->gdev, "framebuffer_alloc failed\n");
+		goto free_urb_list;
+	}
 
 	dev->info = info;
 	info->par = dev;
 	info->pseudo_palette = dev->pseudo_palette;
 	info->fbops = &ufx_ops;
+	INIT_LIST_HEAD(&info->modelist);
 
 	retval = fb_alloc_cmap(&info->cmap, 256, 0);
 	if (retval < 0) {
@@ -1663,11 +1676,6 @@
 		goto destroy_modedb;
 	}
 
-	INIT_DELAYED_WORK(&dev->free_framebuffer_work,
-			  ufx_free_framebuffer_work);
-
-	INIT_LIST_HEAD(&info->modelist);
-
 	retval = ufx_reg_read(dev, 0x3000, &id_rev);
 	check_warn_goto_error(retval, "error %d reading 0x3000 register from device", retval);
 	dev_dbg(dev->gdev, "ID_REV register value 0x%08x", id_rev);
@@ -1697,22 +1705,34 @@
 	check_warn_goto_error(retval, "unable to find common mode for display and adapter");
 
 	retval = ufx_reg_set_bits(dev, 0x4000, 0x00000001);
-	check_warn_goto_error(retval, "error %d enabling graphics engine", retval);
+	if (retval < 0) {
+		dev_err(dev->gdev, "error %d enabling graphics engine", retval);
+		goto setup_modes;
+	}
 
 	/* ready to begin using device */
 	atomic_set(&dev->usb_active, 1);
 
 	dev_dbg(dev->gdev, "checking var");
 	retval = ufx_ops_check_var(&info->var, info);
-	check_warn_goto_error(retval, "error %d ufx_ops_check_var", retval);
+	if (retval < 0) {
+		dev_err(dev->gdev, "error %d ufx_ops_check_var", retval);
+		goto reset_active;
+	}
 
 	dev_dbg(dev->gdev, "setting par");
 	retval = ufx_ops_set_par(info);
-	check_warn_goto_error(retval, "error %d ufx_ops_set_par", retval);
+	if (retval < 0) {
+		dev_err(dev->gdev, "error %d ufx_ops_set_par", retval);
+		goto reset_active;
+	}
 
 	dev_dbg(dev->gdev, "registering framebuffer");
 	retval = register_framebuffer(info);
-	check_warn_goto_error(retval, "error %d register_framebuffer", retval);
+	if (retval < 0) {
+		dev_err(dev->gdev, "error %d register_framebuffer", retval);
+		goto reset_active;
+	}
 
 	dev_info(dev->gdev, "SMSC UDX USB device /dev/fb%d attached. %dx%d resolution."
 		" Using %dK framebuffer memory\n", info->node,
@@ -1720,28 +1740,34 @@
 
 	return 0;
 
-error:
-	fb_dealloc_cmap(&info->cmap);
-destroy_modedb:
+reset_active:
+	atomic_set(&dev->usb_active, 0);
+setup_modes:
 	fb_destroy_modedb(info->monspecs.modedb);
 	vfree(info->screen_base);
 	fb_destroy_modelist(&info->modelist);
+error:
+	fb_dealloc_cmap(&info->cmap);
+destroy_modedb:
 	framebuffer_release(info);
+free_urb_list:
+	if (dev->urbs.count > 0)
+		ufx_free_urb_list(dev);
 put_ref:
 	kref_put(&dev->kref, ufx_free); /* ref for framebuffer */
 	kref_put(&dev->kref, ufx_free); /* last ref from kref_init */
 	return retval;
-
-e_nomem:
-	retval = -ENOMEM;
-	goto put_ref;
 }
 
 static void ufx_usb_disconnect(struct usb_interface *interface)
 {
 	struct ufx_data *dev;
+	struct fb_info *info;
+
+	mutex_lock(&disconnect_mutex);
 
 	dev = usb_get_intfdata(interface);
+	info = dev->info;
 
 	pr_debug("USB disconnect starting\n");
 
@@ -1755,12 +1781,17 @@
 
 	/* if clients still have us open, will be freed on last close */
 	if (dev->fb_count == 0)
-		schedule_delayed_work(&dev->free_framebuffer_work, 0);
+		ufx_free_framebuffer(dev);
 
-	/* release reference taken by kref_init in probe() */
-	kref_put(&dev->kref, ufx_free);
+	/* this function will wait for all in-flight urbs to complete */
+	if (dev->urbs.count > 0)
+		ufx_free_urb_list(dev);
+
+	pr_debug("freeing ufx_data %p", dev);
+
+	unregister_framebuffer(info);
 
-	/* consider ufx_data freed */
+	mutex_unlock(&disconnect_mutex);
 }
 
 static struct usb_driver ufx_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/ssd1307fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/ssd1307fb.c
@@ -370,8 +370,7 @@
 	.fb_imageblit	= ssd1307fb_imageblit,
 };
 
-static void ssd1307fb_deferred_io(struct fb_info *info,
-				struct list_head *pagelist)
+static void ssd1307fb_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
 	ssd1307fb_update_display(info->par);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/sticore.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/sticore.h
@@ -231,7 +231,7 @@
 	 u8 height;
 	 u8 font_type;		/* language type */
 	 u8 bytes_per_char;
-	u32 next_font;
+	s32 next_font;		/* note: signed int */
 	 u8 underline_height;
 	 u8 underline_pos;
 	 u8 res008[2];
@@ -370,6 +370,9 @@
 
 	/* pointer to all internal data */
 	struct sti_all_data *sti_data;
+
+	/* pa_path of this device */
+	char pa_path[24];
 };
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/stifb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/stifb.c
@@ -922,6 +922,28 @@
 /* ------------------- driver specific functions --------------------------- */
 
 static int
+stifb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+	struct stifb_info *fb = container_of(info, struct stifb_info, info);
+
+	if (var->xres != fb->info.var.xres ||
+	    var->yres != fb->info.var.yres ||
+	    var->bits_per_pixel != fb->info.var.bits_per_pixel)
+		return -EINVAL;
+
+	var->xres_virtual = var->xres;
+	var->yres_virtual = var->yres;
+	var->xoffset = 0;
+	var->yoffset = 0;
+	var->grayscale = fb->info.var.grayscale;
+	var->red.length = fb->info.var.red.length;
+	var->green.length = fb->info.var.green.length;
+	var->blue.length = fb->info.var.blue.length;
+
+	return 0;
+}
+
+static int
 stifb_setcolreg(u_int regno, u_int red, u_int green,
 	      u_int blue, u_int transp, struct fb_info *info)
 {
@@ -1041,6 +1063,48 @@
 	SETUP_FB(fb);
 }
 
+#define ARTIST_VRAM_SIZE			0x000804
+#define ARTIST_VRAM_SRC				0x000808
+#define ARTIST_VRAM_SIZE_TRIGGER_WINFILL	0x000a04
+#define ARTIST_VRAM_DEST_TRIGGER_BLOCKMOVE	0x000b00
+#define ARTIST_SRC_BM_ACCESS			0x018008
+#define ARTIST_FGCOLOR				0x018010
+#define ARTIST_BGCOLOR				0x018014
+#define ARTIST_BITMAP_OP			0x01801c
+
+static void
+stifb_fillrect(struct fb_info *info, const struct fb_fillrect *rect)
+{
+	struct stifb_info *fb = container_of(info, struct stifb_info, info);
+
+	if (rect->rop != ROP_COPY ||
+	    (fb->id == S9000_ID_HCRX && fb->info.var.bits_per_pixel == 32))
+		return cfb_fillrect(info, rect);
+
+	SETUP_HW(fb);
+
+	if (fb->info.var.bits_per_pixel == 32) {
+		WRITE_WORD(0xBBA0A000, fb, REG_10);
+
+		NGLE_REALLY_SET_IMAGE_PLANEMASK(fb, 0xffffffff);
+	} else {
+		WRITE_WORD(fb->id == S9000_ID_HCRX ? 0x13a02000 : 0x13a01000, fb, REG_10);
+
+		NGLE_REALLY_SET_IMAGE_PLANEMASK(fb, 0xff);
+	}
+
+	WRITE_WORD(0x03000300, fb, ARTIST_BITMAP_OP);
+	WRITE_WORD(0x2ea01000, fb, ARTIST_SRC_BM_ACCESS);
+	NGLE_QUICK_SET_DST_BM_ACCESS(fb, 0x2ea01000);
+	NGLE_REALLY_SET_IMAGE_FG_COLOR(fb, rect->color);
+	WRITE_WORD(0, fb, ARTIST_BGCOLOR);
+
+	NGLE_SET_DSTXY(fb, (rect->dx << 16) | (rect->dy));
+	SET_LENXY_START_RECFILL(fb, (rect->width << 16) | (rect->height));
+
+	SETUP_FB(fb);
+}
+
 static void __init
 stifb_init_display(struct stifb_info *fb)
 {
@@ -1103,9 +1167,10 @@
 
 static const struct fb_ops stifb_ops = {
 	.owner		= THIS_MODULE,
+	.fb_check_var	= stifb_check_var,
 	.fb_setcolreg	= stifb_setcolreg,
 	.fb_blank	= stifb_blank,
-	.fb_fillrect	= cfb_fillrect,
+	.fb_fillrect	= stifb_fillrect,
 	.fb_copyarea	= stifb_copyarea,
 	.fb_imageblit	= cfb_imageblit,
 };
@@ -1122,6 +1187,7 @@
 	struct stifb_info *fb;
 	struct fb_info *info;
 	unsigned long sti_rom_address;
+	char modestr[32];
 	char *dev_name;
 	int bpp, xres, yres;
 
@@ -1257,7 +1323,7 @@
 	
 	/* limit fbsize to max visible screen size */
 	if (fix->smem_len > yres*fix->line_length)
-		fix->smem_len = yres*fix->line_length;
+		fix->smem_len = ALIGN(yres*fix->line_length, 4*1024*1024);
 	
 	fix->accel = FB_ACCEL_NONE;
 
@@ -1297,9 +1363,12 @@
 		goto out_err0;
 	}
 	info->screen_size = fix->smem_len;
-	info->flags = FBINFO_DEFAULT | FBINFO_HWACCEL_COPYAREA;
+	info->flags = FBINFO_HWACCEL_COPYAREA | FBINFO_HWACCEL_FILLRECT;
 	info->pseudo_palette = &fb->pseudo_palette;
 
+	scnprintf(modestr, sizeof(modestr), "%dx%d-%d", xres, yres, bpp);
+	fb_find_mode(&info->var, info, modestr, NULL, 0, NULL, bpp);
+
 	/* This has to be done !!! */
 	if (fb_alloc_cmap(&info->cmap, NR_PALETTE, 0))
 		goto out_err1;
@@ -1317,11 +1386,11 @@
 		goto out_err3;
 	}
 
+	/* save for primary gfx device detection & unregister_framebuffer() */
+	sti->info = info;
 	if (register_framebuffer(&fb->info) < 0)
 		goto out_err4;
 
-	sti->info = info; /* save for unregister_framebuffer() */
-
 	fb_info(&fb->info, "%s %dx%d-%d frame buffer device, %s, id: %04x, mmio: 0x%04lx\n",
 		fix->id,
 		var->xres, 
@@ -1344,6 +1413,7 @@
 	iounmap(info->screen_base);
 out_err0:
 	kfree(fb);
+	sti->info = NULL;
 	return -ENXIO;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/tgafb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/tgafb.c
@@ -166,6 +166,9 @@
 {
 	struct tga_par *par = (struct tga_par *)info->par;
 
+	if (!var->pixclock)
+		return -EINVAL;
+
 	if (par->tga_type == TGA_TYPE_8PLANE) {
 		if (var->bits_per_pixel != 8)
 			return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/udlfb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/udlfb.c
@@ -27,6 +27,8 @@
 #include <video/udlfb.h>
 #include "edid.h"
 
+#define OUT_EP_NUM	1	/* The endpoint number we will use */
+
 static const struct fb_fix_screeninfo dlfb_fix = {
 	.id =           "udlfb",
 	.type =         FB_TYPE_PACKED_PIXELS,
@@ -778,11 +780,9 @@
  *   in fb_defio will cause a deadlock, when it also tries to
  *   grab the same mutex.
  */
-static void dlfb_dpy_deferred_io(struct fb_info *info,
-				struct list_head *pagelist)
+static void dlfb_dpy_deferred_io(struct fb_info *info, struct list_head *pagereflist)
 {
-	struct page *cur;
-	struct fb_deferred_io *fbdefio = info->fbdefio;
+	struct fb_deferred_io_pageref *pageref;
 	struct dlfb_data *dlfb = info->par;
 	struct urb *urb;
 	char *cmd;
@@ -808,7 +808,8 @@
 	cmd = urb->transfer_buffer;
 
 	/* walk the written page list and render each to device */
-	list_for_each_entry(cur, &fbdefio->pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *cur = pageref->page;
 
 		if (dlfb_render_hline(dlfb, &urb, (char *) info->fix.smem_start,
 				  &cmd, cur->index << PAGE_SHIFT,
@@ -980,6 +981,7 @@
 
 		if (fbdefio) {
 			fbdefio->delay = DL_DEFIO_WRITE_DELAY;
+			fbdefio->sort_pagereflist = true;
 			fbdefio->deferred_io = dlfb_dpy_deferred_io;
 		}
 
@@ -1426,7 +1428,7 @@
 				   struct device_attribute *a, char *buf) {
 	struct fb_info *fb_info = dev_get_drvdata(fbdev);
 	struct dlfb_data *dlfb = fb_info->par;
-	return snprintf(buf, PAGE_SIZE, "%u\n",
+	return sysfs_emit(buf, "%u\n",
 			atomic_read(&dlfb->bytes_rendered));
 }
 
@@ -1434,7 +1436,7 @@
 				   struct device_attribute *a, char *buf) {
 	struct fb_info *fb_info = dev_get_drvdata(fbdev);
 	struct dlfb_data *dlfb = fb_info->par;
-	return snprintf(buf, PAGE_SIZE, "%u\n",
+	return sysfs_emit(buf, "%u\n",
 			atomic_read(&dlfb->bytes_identical));
 }
 
@@ -1442,7 +1444,7 @@
 				   struct device_attribute *a, char *buf) {
 	struct fb_info *fb_info = dev_get_drvdata(fbdev);
 	struct dlfb_data *dlfb = fb_info->par;
-	return snprintf(buf, PAGE_SIZE, "%u\n",
+	return sysfs_emit(buf, "%u\n",
 			atomic_read(&dlfb->bytes_sent));
 }
 
@@ -1450,7 +1452,7 @@
 				   struct device_attribute *a, char *buf) {
 	struct fb_info *fb_info = dev_get_drvdata(fbdev);
 	struct dlfb_data *dlfb = fb_info->par;
-	return snprintf(buf, PAGE_SIZE, "%u\n",
+	return sysfs_emit(buf, "%u\n",
 			atomic_read(&dlfb->cpu_kcycles_used));
 }
 
@@ -1649,8 +1651,9 @@
 	const struct device_attribute *attr;
 	struct dlfb_data *dlfb;
 	struct fb_info *info;
-	int retval = -ENOMEM;
+	int retval;
 	struct usb_device *usbdev = interface_to_usbdev(intf);
+	static u8 out_ep[] = {OUT_EP_NUM + USB_DIR_OUT, 0};
 
 	/* usb initialization */
 	dlfb = kzalloc(sizeof(*dlfb), GFP_KERNEL);
@@ -1664,6 +1667,12 @@
 	dlfb->udev = usb_get_dev(usbdev);
 	usb_set_intfdata(intf, dlfb);
 
+	if (!usb_check_bulk_endpoints(intf, out_ep)) {
+		dev_err(&intf->dev, "Invalid DisplayLink device!\n");
+		retval = -EINVAL;
+		goto error;
+	}
+
 	dev_dbg(&intf->dev, "console enable=%d\n", console);
 	dev_dbg(&intf->dev, "fb_defio enable=%d\n", fb_defio);
 	dev_dbg(&intf->dev, "shadow enable=%d\n", shadow);
@@ -1673,6 +1682,7 @@
 	if (!dlfb_parse_vendor_descriptor(dlfb, intf)) {
 		dev_err(&intf->dev,
 			"firmware not recognized, incompatible device?\n");
+		retval = -ENODEV;
 		goto error;
 	}
 
@@ -1686,8 +1696,10 @@
 
 	/* allocates framebuffer driver structure, not framebuffer memory */
 	info = framebuffer_alloc(0, &dlfb->udev->dev);
-	if (!info)
+	if (!info) {
+		retval = -ENOMEM;
 		goto error;
+	}
 
 	dlfb->info = info;
 	info->par = dlfb;
@@ -1916,7 +1928,8 @@
 		}
 
 		/* urb->transfer_buffer_length set to actual before submit */
-		usb_fill_bulk_urb(urb, dlfb->udev, usb_sndbulkpipe(dlfb->udev, 1),
+		usb_fill_bulk_urb(urb, dlfb->udev,
+			usb_sndbulkpipe(dlfb->udev, OUT_EP_NUM),
 			buf, size, dlfb_urb_completion, unode);
 		urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/uvesafb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/uvesafb.c
@@ -1758,6 +1758,7 @@
 out_unmap:
 	iounmap(info->screen_base);
 out_mem:
+	arch_phys_wc_del(par->mtrr_handle);
 	release_mem_region(info->fix.smem_start, info->fix.smem_len);
 out_reg:
 	release_region(0x3c0, 32);
@@ -1934,10 +1935,10 @@
 		}
 	}
 
-	cn_del_callback(&uvesafb_cn_id);
 	driver_remove_file(&uvesafb_driver.driver, &driver_attr_v86d);
 	platform_device_unregister(uvesafb_device);
 	platform_driver_unregister(&uvesafb_driver);
+	cn_del_callback(&uvesafb_cn_id);
 }
 
 module_exit(uvesafb_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/vermilion/vermilion.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/vermilion/vermilion.c
@@ -277,8 +277,10 @@
 
 	mutex_unlock(&vml_mutex);
 
-	if (pci_enable_device(par->gpu) < 0)
+	if (pci_enable_device(par->gpu) < 0) {
+		pci_dev_put(par->gpu);
 		return -ENODEV;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/vesafb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/vesafb.c
@@ -179,6 +179,10 @@
 	return err;
 }
 
+/*
+ * fb_ops.fb_destroy is called by the last put_fb_info() call at the end
+ * of unregister_framebuffer() or fb_release(). Do any cleanup here.
+ */
 static void vesafb_destroy(struct fb_info *info)
 {
 	struct vesafb_par *par = info->par;
@@ -188,6 +192,8 @@
 	if (info->screen_base)
 		iounmap(info->screen_base);
 	release_mem_region(info->apertures->ranges[0].base, info->apertures->ranges[0].size);
+
+	framebuffer_release(info);
 }
 
 static struct fb_ops vesafb_ops = {
@@ -484,10 +490,11 @@
 {
 	struct fb_info *info = platform_get_drvdata(pdev);
 
-	unregister_framebuffer(info);
 	if (((struct vesafb_par *)(info->par))->region)
 		release_region(0x3c0, 32);
-	framebuffer_release(info);
+
+	/* vesafb_destroy takes care of info cleanup */
+	unregister_framebuffer(info);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/vga16fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/vga16fb.c
@@ -184,6 +184,25 @@
 	vga_io_w(VGA_GFX_I, index);
 }
 
+/* Check if the video mode is supported by the driver */
+static inline int check_mode_supported(void)
+{
+	/* non-x86 architectures treat orig_video_isVGA as a boolean flag */
+#if defined(CONFIG_X86)
+	/* only EGA and VGA in 16 color graphic mode are supported */
+	if (screen_info.orig_video_isVGA != VIDEO_TYPE_EGAC &&
+	    screen_info.orig_video_isVGA != VIDEO_TYPE_VGAC)
+		return -ENODEV;
+
+	if (screen_info.orig_video_mode != 0x0D &&	/* 320x200/4 (EGA) */
+	    screen_info.orig_video_mode != 0x0E &&	/* 640x200/4 (EGA) */
+	    screen_info.orig_video_mode != 0x10 &&	/* 640x350/4 (EGA) */
+	    screen_info.orig_video_mode != 0x12)	/* 640x480/4 (VGA) */
+		return -ENODEV;
+#endif
+	return 0;
+}
+
 static void vga16fb_pan_var(struct fb_info *info, 
 			    struct fb_var_screeninfo *var)
 {
@@ -1422,6 +1441,11 @@
 
 	vga16fb_setup(option);
 #endif
+
+	ret = check_mode_supported();
+	if (ret)
+		return ret;
+
 	ret = platform_driver_register(&vga16fb_driver);
 
 	if (!ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/via/accel.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/via/accel.c
@@ -115,7 +115,7 @@
 
 	if (op != VIA_BITBLT_FILL) {
 		tmp = src_mem ? 0 : src_addr;
-		if (dst_addr & 0xE0000007) {
+		if (tmp & 0xE0000007) {
 			printk(KERN_WARNING "hw_bitblt_1: Unsupported source "
 				"address %X\n", tmp);
 			return -EINVAL;
@@ -260,7 +260,7 @@
 		writel(tmp, engine + 0x18);
 
 		tmp = src_mem ? 0 : src_addr;
-		if (dst_addr & 0xE0000007) {
+		if (tmp & 0xE0000007) {
 			printk(KERN_WARNING "hw_bitblt_2: Unsupported source "
 				"address %X\n", tmp);
 			return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/via/via-core.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/via/via-core.c
@@ -725,7 +725,14 @@
 		return ret;
 	viafb_i2c_init();
 	viafb_gpio_init();
-	return pci_register_driver(&via_driver);
+	ret = pci_register_driver(&via_driver);
+	if (ret) {
+		viafb_gpio_exit();
+		viafb_i2c_exit();
+		return ret;
+	}
+
+	return 0;
 }
 
 static void __exit via_core_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/vt8623fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/vt8623fb.c
@@ -504,6 +504,8 @@
 			 (info->var.vmode & FB_VMODE_DOUBLE) ? 2 : 1, 1,
 			 1, info->node);
 
+	if (screen_size > info->screen_size)
+		screen_size = info->screen_size;
 	memset_io(info->screen_base, 0x00, screen_size);
 
 	/* Device and screen back on */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/w100fb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/w100fb.c
@@ -770,12 +770,18 @@
 		fb_dealloc_cmap(&info->cmap);
 		kfree(info->pseudo_palette);
 	}
-	if (remapped_fbuf != NULL)
+	if (remapped_fbuf != NULL) {
 		iounmap(remapped_fbuf);
-	if (remapped_regs != NULL)
+		remapped_fbuf = NULL;
+	}
+	if (remapped_regs != NULL) {
 		iounmap(remapped_regs);
-	if (remapped_base != NULL)
+		remapped_regs = NULL;
+	}
+	if (remapped_base != NULL) {
 		iounmap(remapped_base);
+		remapped_base = NULL;
+	}
 	if (info)
 		framebuffer_release(info);
 	return err;
@@ -795,8 +801,11 @@
 	fb_dealloc_cmap(&info->cmap);
 
 	iounmap(remapped_base);
+	remapped_base = NULL;
 	iounmap(remapped_regs);
+	remapped_regs = NULL;
 	iounmap(remapped_fbuf);
+	remapped_fbuf = NULL;
 
 	framebuffer_release(info);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/video/fbdev/xen-fbfront.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/video/fbdev/xen-fbfront.c
@@ -181,17 +181,17 @@
 		xenfb_do_update(info, x1, y1, x2 - x1 + 1, y2 - y1 + 1);
 }
 
-static void xenfb_deferred_io(struct fb_info *fb_info,
-			      struct list_head *pagelist)
+static void xenfb_deferred_io(struct fb_info *fb_info, struct list_head *pagereflist)
 {
 	struct xenfb_info *info = fb_info->par;
-	struct page *page;
+	struct fb_deferred_io_pageref *pageref;
 	unsigned long beg, end;
 	int y1, y2, miny, maxy;
 
 	miny = INT_MAX;
 	maxy = 0;
-	list_for_each_entry(page, pagelist, lru) {
+	list_for_each_entry(pageref, pagereflist, list) {
+		struct page *page = pageref->page;
 		beg = page->index << PAGE_SHIFT;
 		end = beg + PAGE_SIZE - 1;
 		y1 = beg / fb_info->fix.line_length;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virt/acrn/acrn_drv.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/virt/acrn/acrn_drv.h
@@ -48,6 +48,7 @@
  * @reserved:		Reserved.
  * @regions_num:	The number of vm_memory_region_op.
  * @regions_gpa:	Physical address of a vm_memory_region_op array.
+ * @regions_op:		Flexible array of vm_memory_region_op.
  *
  * HC_VM_SET_MEMORY_REGIONS uses this structure to manage EPT mappings of
  * multiple memory regions of a User VM. A &struct vm_memory_region_batch
@@ -55,10 +56,11 @@
  * ACRN Hypervisor.
  */
 struct vm_memory_region_batch {
-	u16	vmid;
-	u16	reserved[3];
-	u32	regions_num;
-	u64	regions_gpa;
+	u16			   vmid;
+	u16			   reserved[3];
+	u32			   regions_num;
+	u64			   regions_gpa;
+	struct vm_memory_region_op regions_op[];
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virt/acrn/hsm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virt/acrn/hsm.c
@@ -49,7 +49,7 @@
 	switch (cmd & PMCMD_TYPE_MASK) {
 	case ACRN_PMCMD_GET_PX_CNT:
 	case ACRN_PMCMD_GET_CX_CNT:
-		pm_info = kmalloc(sizeof(u64), GFP_KERNEL);
+		pm_info = kzalloc(sizeof(u64), GFP_KERNEL);
 		if (!pm_info)
 			return -ENOMEM;
 
@@ -64,7 +64,7 @@
 		kfree(pm_info);
 		break;
 	case ACRN_PMCMD_GET_PX_DATA:
-		px_data = kmalloc(sizeof(*px_data), GFP_KERNEL);
+		px_data = kzalloc(sizeof(*px_data), GFP_KERNEL);
 		if (!px_data)
 			return -ENOMEM;
 
@@ -79,7 +79,7 @@
 		kfree(px_data);
 		break;
 	case ACRN_PMCMD_GET_CX_DATA:
-		cx_data = kmalloc(sizeof(*cx_data), GFP_KERNEL);
+		cx_data = kzalloc(sizeof(*cx_data), GFP_KERNEL);
 		if (!cx_data)
 			return -ENOMEM;
 
@@ -134,8 +134,10 @@
 		if (IS_ERR(vm_param))
 			return PTR_ERR(vm_param);
 
-		if ((vm_param->reserved0 | vm_param->reserved1) != 0)
+		if ((vm_param->reserved0 | vm_param->reserved1) != 0) {
+			kfree(vm_param);
 			return -EINVAL;
+		}
 
 		vm = acrn_vm_create(vm, vm_param);
 		if (!vm) {
@@ -180,21 +182,29 @@
 			return PTR_ERR(cpu_regs);
 
 		for (i = 0; i < ARRAY_SIZE(cpu_regs->reserved); i++)
-			if (cpu_regs->reserved[i])
+			if (cpu_regs->reserved[i]) {
+				kfree(cpu_regs);
 				return -EINVAL;
+			}
 
 		for (i = 0; i < ARRAY_SIZE(cpu_regs->vcpu_regs.reserved_32); i++)
-			if (cpu_regs->vcpu_regs.reserved_32[i])
+			if (cpu_regs->vcpu_regs.reserved_32[i]) {
+				kfree(cpu_regs);
 				return -EINVAL;
+			}
 
 		for (i = 0; i < ARRAY_SIZE(cpu_regs->vcpu_regs.reserved_64); i++)
-			if (cpu_regs->vcpu_regs.reserved_64[i])
+			if (cpu_regs->vcpu_regs.reserved_64[i]) {
+				kfree(cpu_regs);
 				return -EINVAL;
+			}
 
 		for (i = 0; i < ARRAY_SIZE(cpu_regs->vcpu_regs.gdt.reserved); i++)
 			if (cpu_regs->vcpu_regs.gdt.reserved[i] |
-			    cpu_regs->vcpu_regs.idt.reserved[i])
+			    cpu_regs->vcpu_regs.idt.reserved[i]) {
+				kfree(cpu_regs);
 				return -EINVAL;
+			}
 
 		ret = hcall_set_vcpu_regs(vm->vmid, virt_to_phys(cpu_regs));
 		if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virt/acrn/mm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virt/acrn/mm.c
@@ -155,20 +155,84 @@
 int acrn_vm_ram_map(struct acrn_vm *vm, struct acrn_vm_memmap *memmap)
 {
 	struct vm_memory_region_batch *regions_info;
-	int nr_pages, i = 0, order, nr_regions = 0;
+	int nr_pages, i, order, nr_regions = 0;
 	struct vm_memory_mapping *region_mapping;
 	struct vm_memory_region_op *vm_region;
 	struct page **pages = NULL, *page;
 	void *remap_vaddr;
 	int ret, pinned;
 	u64 user_vm_pa;
+	struct vm_area_struct *vma;
 
 	if (!vm || !memmap)
 		return -EINVAL;
 
 	/* Get the page number of the map region */
 	nr_pages = memmap->len >> PAGE_SHIFT;
-	pages = vzalloc(nr_pages * sizeof(struct page *));
+	if (!nr_pages)
+		return -EINVAL;
+
+	mmap_read_lock(current->mm);
+	vma = vma_lookup(current->mm, memmap->vma_base);
+	if (vma && ((vma->vm_flags & VM_PFNMAP) != 0)) {
+		unsigned long start_pfn, cur_pfn;
+		spinlock_t *ptl;
+		bool writable;
+		pte_t *ptep;
+
+		if ((memmap->vma_base + memmap->len) > vma->vm_end) {
+			mmap_read_unlock(current->mm);
+			return -EINVAL;
+		}
+
+		for (i = 0; i < nr_pages; i++) {
+			ret = follow_pte(vma->vm_mm,
+					 memmap->vma_base + i * PAGE_SIZE,
+					 &ptep, &ptl);
+			if (ret)
+				break;
+
+			cur_pfn = pte_pfn(ptep_get(ptep));
+			if (i == 0)
+				start_pfn = cur_pfn;
+			writable = !!pte_write(ptep_get(ptep));
+			pte_unmap_unlock(ptep, ptl);
+
+			/* Disallow write access if the PTE is not writable. */
+			if (!writable &&
+			    (memmap->attr & ACRN_MEM_ACCESS_WRITE)) {
+				ret = -EFAULT;
+				break;
+			}
+
+			/* Disallow refcounted pages. */
+			if (pfn_valid(cur_pfn) &&
+			    !PageReserved(pfn_to_page(cur_pfn))) {
+				ret = -EFAULT;
+				break;
+			}
+
+			/* Disallow non-contiguous ranges. */
+			if (cur_pfn != start_pfn + i) {
+				ret = -EINVAL;
+				break;
+			}
+		}
+		mmap_read_unlock(current->mm);
+
+		if (ret) {
+			dev_dbg(acrn_dev.this_device,
+				"Failed to lookup PFN at VMA:%pK.\n", (void *)memmap->vma_base);
+			return ret;
+		}
+
+		return acrn_mm_region_add(vm, memmap->user_vm_pa,
+			 PFN_PHYS(start_pfn), memmap->len,
+			 ACRN_MEM_TYPE_WB, memmap->attr);
+	}
+	mmap_read_unlock(current->mm);
+
+	pages = vzalloc(array_size(nr_pages, sizeof(*pages)));
 	if (!pages)
 		return -ENOMEM;
 
@@ -211,31 +275,28 @@
 	mutex_unlock(&vm->regions_mapping_lock);
 
 	/* Calculate count of vm_memory_region_op */
-	while (i < nr_pages) {
+	for (i = 0; i < nr_pages; i += 1 << order) {
 		page = pages[i];
 		VM_BUG_ON_PAGE(PageTail(page), page);
 		order = compound_order(page);
 		nr_regions++;
-		i += 1 << order;
 	}
 
 	/* Prepare the vm_memory_region_batch */
-	regions_info = kzalloc(sizeof(*regions_info) +
-			       sizeof(*vm_region) * nr_regions,
-			       GFP_KERNEL);
+	regions_info = kzalloc(struct_size(regions_info, regions_op,
+					   nr_regions), GFP_KERNEL);
 	if (!regions_info) {
 		ret = -ENOMEM;
 		goto unmap_kernel_map;
 	}
 
 	/* Fill each vm_memory_region_op */
-	vm_region = (struct vm_memory_region_op *)(regions_info + 1);
+	vm_region = regions_info->regions_op;
 	regions_info->vmid = vm->vmid;
 	regions_info->regions_num = nr_regions;
 	regions_info->regions_gpa = virt_to_phys(vm_region);
 	user_vm_pa = memmap->user_vm_pa;
-	i = 0;
-	while (i < nr_pages) {
+	for (i = 0; i < nr_pages; i += 1 << order) {
 		u32 region_size;
 
 		page = pages[i];
@@ -251,7 +312,6 @@
 
 		vm_region++;
 		user_vm_pa += region_size;
-		i += 1 << order;
 	}
 
 	/* Inform the ACRN Hypervisor to set up EPT mappings */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virt/nitro_enclaves/ne_misc_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virt/nitro_enclaves/ne_misc_dev.c
@@ -886,8 +886,9 @@
 			goto put_pages;
 		}
 
-		gup_rc = get_user_pages(mem_region.userspace_addr + memory_size, 1, FOLL_GET,
-					ne_mem_region->pages + i, NULL);
+		gup_rc = get_user_pages_unlocked(mem_region.userspace_addr + memory_size, 1,
+						 ne_mem_region->pages + i, FOLL_GET);
+
 		if (gup_rc < 0) {
 			rc = gup_rc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virt/vboxguest/vboxguest_linux.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virt/vboxguest/vboxguest_linux.c
@@ -356,8 +356,8 @@
 		goto err_vbg_core_exit;
 	}
 
-	ret = devm_request_irq(dev, pci->irq, vbg_core_isr, IRQF_SHARED,
-			       DEVICE_NAME, gdev);
+	ret = request_irq(pci->irq, vbg_core_isr, IRQF_SHARED, DEVICE_NAME,
+			  gdev);
 	if (ret) {
 		vbg_err("vboxguest: Error requesting irq: %d\n", ret);
 		goto err_vbg_core_exit;
@@ -367,7 +367,7 @@
 	if (ret) {
 		vbg_err("vboxguest: Error misc_register %s failed: %d\n",
 			DEVICE_NAME, ret);
-		goto err_vbg_core_exit;
+		goto err_free_irq;
 	}
 
 	ret = misc_register(&gdev->misc_device_user);
@@ -403,6 +403,8 @@
 	misc_deregister(&gdev->misc_device_user);
 err_unregister_misc_device:
 	misc_deregister(&gdev->misc_device);
+err_free_irq:
+	free_irq(pci->irq, gdev);
 err_vbg_core_exit:
 	vbg_core_exit(gdev);
 err_disable_pcidev:
@@ -419,6 +421,7 @@
 	vbg_gdev = NULL;
 	mutex_unlock(&vbg_gdev_mutex);
 
+	free_irq(pci->irq, gdev);
 	device_remove_file(gdev->dev, &dev_attr_host_features);
 	device_remove_file(gdev->dev, &dev_attr_host_version);
 	misc_deregister(&gdev->misc_device_user);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio.c
@@ -166,14 +166,13 @@
 }
 EXPORT_SYMBOL_GPL(virtio_add_status);
 
-int virtio_finalize_features(struct virtio_device *dev)
+/* Do some validation, then set FEATURES_OK */
+static int virtio_features_ok(struct virtio_device *dev)
 {
-	int ret = dev->config->finalize_features(dev);
 	unsigned status;
+	int ret;
 
 	might_sleep();
-	if (ret)
-		return ret;
 
 	ret = arch_has_restricted_virtio_memory_access();
 	if (ret) {
@@ -202,7 +201,6 @@
 	}
 	return 0;
 }
-EXPORT_SYMBOL_GPL(virtio_finalize_features);
 
 static int virtio_dev_probe(struct device *_d)
 {
@@ -239,17 +237,6 @@
 		driver_features_legacy = driver_features;
 	}
 
-	/*
-	 * Some devices detect legacy solely via F_VERSION_1. Write
-	 * F_VERSION_1 to force LE config space accesses before FEATURES_OK for
-	 * these when needed.
-	 */
-	if (drv->validate && !virtio_legacy_is_little_endian()
-			  && device_features & BIT_ULL(VIRTIO_F_VERSION_1)) {
-		dev->features = BIT_ULL(VIRTIO_F_VERSION_1);
-		dev->config->finalize_features(dev);
-	}
-
 	if (device_features & (1ULL << VIRTIO_F_VERSION_1))
 		dev->features = driver_features & device_features;
 	else
@@ -260,13 +247,26 @@
 		if (device_features & (1ULL << i))
 			__virtio_set_bit(dev, i);
 
+	err = dev->config->finalize_features(dev);
+	if (err)
+		goto err;
+
 	if (drv->validate) {
+		u64 features = dev->features;
+
 		err = drv->validate(dev);
 		if (err)
 			goto err;
+
+		/* Did validation change any features? Then write them again. */
+		if (features != dev->features) {
+			err = dev->config->finalize_features(dev);
+			if (err)
+				goto err;
+		}
 	}
 
-	err = virtio_finalize_features(dev);
+	err = virtio_features_ok(dev);
 	if (err)
 		goto err;
 
@@ -455,13 +455,19 @@
 int virtio_device_freeze(struct virtio_device *dev)
 {
 	struct virtio_driver *drv = drv_to_virtio(dev->dev.driver);
+	int ret;
 
 	virtio_config_disable(dev);
 
 	dev->failed = dev->config->get_status(dev) & VIRTIO_CONFIG_S_FAILED;
 
-	if (drv && drv->freeze)
-		return drv->freeze(dev);
+	if (drv && drv->freeze) {
+		ret = drv->freeze(dev);
+		if (ret) {
+			virtio_config_enable(dev);
+			return ret;
+		}
+	}
 
 	return 0;
 }
@@ -490,7 +496,11 @@
 	/* We have a driver! */
 	virtio_add_status(dev, VIRTIO_CONFIG_S_DRIVER);
 
-	ret = virtio_finalize_features(dev);
+	ret = dev->config->finalize_features(dev);
+	if (ret)
+		goto err;
+
+	ret = virtio_features_ok(dev);
 	if (ret)
 		goto err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_balloon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_balloon.c
@@ -402,7 +402,11 @@
 	virtio_cread_le(vb->vdev, struct virtio_balloon_config, num_pages,
 			&num_pages);
 
-	target = num_pages;
+	/*
+	 * Aligned up to guest page size to avoid inflating and deflating
+	 * balloon endlessly.
+	 */
+	target = ALIGN(num_pages, VIRTIO_BALLOON_PAGES_PER_PAGE);
 	return target - vb->num_pages;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_mem.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_mem.c
@@ -577,7 +577,7 @@
 		return -ENOMEM;
 
 	mutex_lock(&vm->hotplug_mutex);
-	if (new_bitmap)
+	if (vm->sbm.sb_states)
 		memcpy(new_bitmap, vm->sbm.sb_states, old_pages * PAGE_SIZE);
 
 	old_bitmap = vm->sbm.sb_states;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_mmio.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_mmio.c
@@ -62,6 +62,7 @@
 #include <linux/list.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/pm.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/virtio.h>
@@ -543,15 +544,36 @@
 	.get_shm_region = vm_get_shm_region,
 };
 
+#ifdef CONFIG_PM_SLEEP
+static int virtio_mmio_freeze(struct device *dev)
+{
+	struct virtio_mmio_device *vm_dev = dev_get_drvdata(dev);
+
+	return virtio_device_freeze(&vm_dev->vdev);
+}
+
+static int virtio_mmio_restore(struct device *dev)
+{
+	struct virtio_mmio_device *vm_dev = dev_get_drvdata(dev);
+
+	if (vm_dev->version == 1)
+		writel(PAGE_SIZE, vm_dev->base + VIRTIO_MMIO_GUEST_PAGE_SIZE);
+
+	return virtio_device_restore(&vm_dev->vdev);
+}
+
+static const struct dev_pm_ops virtio_mmio_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(virtio_mmio_freeze, virtio_mmio_restore)
+};
+#endif
 
 static void virtio_mmio_release_dev(struct device *_d)
 {
 	struct virtio_device *vdev =
 			container_of(_d, struct virtio_device, dev);
 	struct virtio_mmio_device *vm_dev = to_virtio_mmio_device(vdev);
-	struct platform_device *pdev = vm_dev->pdev;
 
-	devm_kfree(&pdev->dev, vm_dev);
+	kfree(vm_dev);
 }
 
 /* Platform device */
@@ -562,7 +584,7 @@
 	unsigned long magic;
 	int rc;
 
-	vm_dev = devm_kzalloc(&pdev->dev, sizeof(*vm_dev), GFP_KERNEL);
+	vm_dev = kzalloc(sizeof(*vm_dev), GFP_KERNEL);
 	if (!vm_dev)
 		return -ENOMEM;
 
@@ -574,14 +596,17 @@
 	spin_lock_init(&vm_dev->lock);
 
 	vm_dev->base = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(vm_dev->base))
-		return PTR_ERR(vm_dev->base);
+	if (IS_ERR(vm_dev->base)) {
+		rc = PTR_ERR(vm_dev->base);
+		goto free_vm_dev;
+	}
 
 	/* Check magic value */
 	magic = readl(vm_dev->base + VIRTIO_MMIO_MAGIC_VALUE);
 	if (magic != ('v' | 'i' << 8 | 'r' << 16 | 't' << 24)) {
 		dev_warn(&pdev->dev, "Wrong magic value 0x%08lx!\n", magic);
-		return -ENODEV;
+		rc = -ENODEV;
+		goto free_vm_dev;
 	}
 
 	/* Check device version */
@@ -589,7 +614,8 @@
 	if (vm_dev->version < 1 || vm_dev->version > 2) {
 		dev_err(&pdev->dev, "Version %ld not supported!\n",
 				vm_dev->version);
-		return -ENXIO;
+		rc = -ENXIO;
+		goto free_vm_dev;
 	}
 
 	vm_dev->vdev.id.device = readl(vm_dev->base + VIRTIO_MMIO_DEVICE_ID);
@@ -598,7 +624,8 @@
 		 * virtio-mmio device with an ID 0 is a (dummy) placeholder
 		 * with no function. End probing now with no error reported.
 		 */
-		return -ENODEV;
+		rc = -ENODEV;
+		goto free_vm_dev;
 	}
 	vm_dev->vdev.id.vendor = readl(vm_dev->base + VIRTIO_MMIO_VENDOR_ID);
 
@@ -628,6 +655,10 @@
 		put_device(&vm_dev->vdev.dev);
 
 	return rc;
+
+free_vm_dev:
+	kfree(vm_dev);
+	return rc;
 }
 
 static int virtio_mmio_remove(struct platform_device *pdev)
@@ -688,6 +719,7 @@
 	if (!vm_cmdline_parent_registered) {
 		err = device_register(&vm_cmdline_parent);
 		if (err) {
+			put_device(&vm_cmdline_parent);
 			pr_err("Failed to register parent device!\n");
 			return err;
 		}
@@ -785,6 +817,9 @@
 		.name	= "virtio-mmio",
 		.of_match_table	= virtio_mmio_match,
 		.acpi_match_table = ACPI_PTR(virtio_mmio_acpi_match),
+#ifdef CONFIG_PM_SLEEP
+		.pm	= &virtio_mmio_pm_ops,
+#endif
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_pci_common.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_pci_common.c
@@ -254,8 +254,7 @@
 
 	if (vp_dev->msix_affinity_masks) {
 		for (i = 0; i < vp_dev->msix_vectors; i++)
-			if (vp_dev->msix_affinity_masks[i])
-				free_cpumask_var(vp_dev->msix_affinity_masks[i]);
+			free_cpumask_var(vp_dev->msix_affinity_masks[i]);
 	}
 
 	if (vp_dev->msix_enabled) {
@@ -340,8 +339,10 @@
 				  vring_interrupt, 0,
 				  vp_dev->msix_names[msix_vec],
 				  vqs[i]);
-		if (err)
+		if (err) {
+			vp_del_vq(vqs[i]);
 			goto error_find;
+		}
 	}
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_pci_modern.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_pci_modern.c
@@ -196,7 +196,7 @@
 	int err;
 
 	if (index >= vp_modern_get_num_queues(mdev))
-		return ERR_PTR(-ENOENT);
+		return ERR_PTR(-EINVAL);
 
 	/* Check if queue is either not available or already active. */
 	num = vp_modern_get_queue_size(mdev, index);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_pci_modern_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_pci_modern_dev.c
@@ -340,6 +340,7 @@
 err_map_isr:
 	pci_iounmap(pci_dev, mdev->common);
 err_map_common:
+	pci_release_selected_regions(pci_dev, mdev->modern_bars);
 	return err;
 }
 EXPORT_SYMBOL_GPL(vp_modern_probe);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_ring.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_ring.c
@@ -268,7 +268,7 @@
 	size_t max_segment_size = SIZE_MAX;
 
 	if (vring_use_dma_api(vdev))
-		max_segment_size = dma_max_mapping_size(&vdev->dev);
+		max_segment_size = dma_max_mapping_size(vdev->dev.parent);
 
 	return max_segment_size;
 }
@@ -809,6 +809,14 @@
 
 	if (!(vq->split.avail_flags_shadow & VRING_AVAIL_F_NO_INTERRUPT)) {
 		vq->split.avail_flags_shadow |= VRING_AVAIL_F_NO_INTERRUPT;
+
+		/*
+		 * If device triggered an event already it won't trigger one again:
+		 * no need to disable.
+		 */
+		if (vq->event_triggered)
+			return;
+
 		if (vq->event)
 			/* TODO: this is a hack. Figure out a cleaner value to write. */
 			vring_used_event(&vq->split.vring) = 0x0;
@@ -1065,6 +1073,8 @@
 
 	head = vq->packed.next_avail_idx;
 	desc = alloc_indirect_packed(total_sg, gfp);
+	if (!desc)
+		return -ENOMEM;
 
 	if (unlikely(vq->vq.num_free < 1)) {
 		pr_debug("Can't add buf len 1 - avail = 0\n");
@@ -1176,6 +1186,7 @@
 	unsigned int i, n, c, descs_used, err_idx;
 	__le16 head_flags, flags;
 	u16 head, id, prev, curr, avail_used_flags;
+	int err;
 
 	START_USE(vq);
 
@@ -1191,9 +1202,16 @@
 
 	BUG_ON(total_sg == 0);
 
-	if (virtqueue_use_indirect(_vq, total_sg))
-		return virtqueue_add_indirect_packed(vq, sgs, total_sg,
-				out_sgs, in_sgs, data, gfp);
+	if (virtqueue_use_indirect(_vq, total_sg)) {
+		err = virtqueue_add_indirect_packed(vq, sgs, total_sg, out_sgs,
+						    in_sgs, data, gfp);
+		if (err != -ENOMEM) {
+			END_USE(vq);
+			return err;
+		}
+
+		/* fall back on direct */
+	}
 
 	head = vq->packed.next_avail_idx;
 	avail_used_flags = vq->packed.avail_used_flags;
@@ -1253,7 +1271,7 @@
 		}
 	}
 
-	if (i < head)
+	if (i <= head)
 		vq->packed.avail_wrap_counter ^= 1;
 
 	/* We're using some buffers from the free list. */
@@ -1490,6 +1508,14 @@
 
 	if (vq->packed.event_flags_shadow != VRING_PACKED_EVENT_FLAG_DISABLE) {
 		vq->packed.event_flags_shadow = VRING_PACKED_EVENT_FLAG_DISABLE;
+
+		/*
+		 * If device triggered an event already it won't trigger one again:
+		 * no need to disable.
+		 */
+		if (vq->event_triggered)
+			return;
+
 		vq->packed.vring.driver->flags =
 			cpu_to_le16(vq->packed.event_flags_shadow);
 	}
@@ -2009,12 +2035,6 @@
 {
 	struct vring_virtqueue *vq = to_vvq(_vq);
 
-	/* If device triggered an event already it won't trigger one again:
-	 * no need to disable.
-	 */
-	if (vq->event_triggered)
-		return;
-
 	if (vq->packed_ring)
 		virtqueue_disable_cb_packed(_vq);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/virtio/virtio_vdpa.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/virtio/virtio_vdpa.c
@@ -182,6 +182,7 @@
 	/* Setup virtqueue callback */
 	cb.callback = virtio_vdpa_virtqueue_cb;
 	cb.private = info;
+	cb.trigger = NULL;
 	ops->set_vq_cb(vdpa, index, &cb);
 	ops->set_vq_num(vdpa, index, virtqueue_get_vring_size(vq));
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vme/bridges/vme_fake.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vme/bridges/vme_fake.c
@@ -1073,6 +1073,8 @@
 
 	/* We need a fake parent device */
 	vme_root = __root_device_register("vme", THIS_MODULE);
+	if (IS_ERR(vme_root))
+		return PTR_ERR(vme_root);
 
 	/* If we want to support more than one bridge at some point, we need to
 	 * dynamically allocate this so we get one per device.
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/vme/bridges/vme_tsi148.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/vme/bridges/vme_tsi148.c
@@ -1765,6 +1765,7 @@
 	return 0;
 
 err_dma:
+	list_del(&entry->list);
 err_dest:
 err_source:
 err_align:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/masters/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/masters/Kconfig
@@ -5,6 +5,17 @@
 
 menu "1-wire Bus Masters"
 
+config W1_MASTER_AMD_AXI
+	tristate "AMD AXI 1-wire bus host"
+	help
+	  Say Y here is you want to support the AMD AXI 1-wire IP core.
+	  This driver makes use of the programmable logic IP to perform
+	  correctly timed 1 wire transactions without relying on GPIO timing
+	  through the kernel.
+
+	  This driver can also be built as a module.  If so, the module will be
+	  called amd_w1_axi.
+
 config W1_MASTER_MATROX
 	tristate "Matrox G400 transport layer for 1-wire"
 	depends on PCI
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/masters/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/masters/Makefile
@@ -3,6 +3,7 @@
 # Makefile for 1-wire bus master drivers.
 #
 
+obj-$(CONFIG_W1_MASTER_AMD_AXI)		+= amd_axi_w1.o
 obj-$(CONFIG_W1_MASTER_MATROX)		+= matrox_w1.o
 obj-$(CONFIG_W1_MASTER_DS2490)		+= ds2490.o
 obj-$(CONFIG_W1_MASTER_DS2482)		+= ds2482.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/masters/amd_axi_w1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/masters/amd_axi_w1.c
@@ -0,0 +1,396 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * amd_axi_w1 - AMD 1Wire programmable logic bus host driver
+ *
+ * Copyright (C) 2022-2023 Advanced Micro Devices, Inc. All Rights Reserved.
+ */
+
+#include <linux/atomic.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+
+#include <linux/w1.h>
+
+/* 1-wire AMD IP definition */
+#define AXIW1_IPID	0x10ee4453
+/* Registers offset */
+#define AXIW1_INST_REG	0x0
+#define AXIW1_CTRL_REG	0x4
+#define AXIW1_IRQE_REG	0x8
+#define AXIW1_STAT_REG	0xC
+#define AXIW1_DATA_REG	0x10
+#define AXIW1_IPVER_REG	0x18
+#define AXIW1_IPID_REG	0x1C
+/* Instructions */
+#define AXIW1_INITPRES	0x0800
+#define AXIW1_READBIT	0x0C00
+#define AXIW1_WRITEBIT	0x0E00
+#define AXIW1_READBYTE	0x0D00
+#define AXIW1_WRITEBYTE	0x0F00
+/* Status flag masks */
+#define AXIW1_DONE	BIT(0)
+#define AXIW1_READY	BIT(4)
+#define AXIW1_PRESENCE	BIT(31)
+#define AXIW1_MAJORVER_MASK	GENMASK(23, 8)
+#define AXIW1_MINORVER_MASK	GENMASK(7, 0)
+/* Control flag */
+#define AXIW1_GO	BIT(0)
+#define AXI_CLEAR	0
+#define AXI_RESET	BIT(31)
+#define AXIW1_READDATA	BIT(0)
+/* Interrupt Enable */
+#define AXIW1_READY_IRQ_EN	BIT(4)
+#define AXIW1_DONE_IRQ_EN	BIT(0)
+
+#define AXIW1_TIMEOUT	msecs_to_jiffies(100)
+
+#define DRIVER_NAME	"amd_axi_w1"
+
+struct amd_axi_w1_local {
+	struct device *dev;
+	void __iomem *base_addr;
+	int irq;
+	atomic_t flag;			/* Set on IRQ, cleared once serviced */
+	wait_queue_head_t wait_queue;
+	struct w1_bus_master bus_host;
+};
+
+/**
+ * amd_axi_w1_wait_irq_interruptible_timeout() - Wait for IRQ with timeout.
+ *
+ * @amd_axi_w1_local:	Pointer to device structure
+ * @IRQ:		IRQ channel to wait on
+ *
+ * Return:		%0 - OK, %-EINTR - Interrupted, %-EBUSY - Timed out
+ */
+static int amd_axi_w1_wait_irq_interruptible_timeout(struct amd_axi_w1_local *amd_axi_w1_local,
+						     u32 IRQ)
+{
+	int ret;
+
+	/* Enable the IRQ requested and wait for flag to indicate it's been triggered */
+	iowrite32(IRQ, amd_axi_w1_local->base_addr + AXIW1_IRQE_REG);
+	ret = wait_event_interruptible_timeout(amd_axi_w1_local->wait_queue,
+					       atomic_read(&amd_axi_w1_local->flag) != 0,
+					       AXIW1_TIMEOUT);
+	if (ret < 0) {
+		dev_err(amd_axi_w1_local->dev, "Wait IRQ Interrupted\n");
+		return -EINTR;
+	}
+
+	if (!ret) {
+		dev_err(amd_axi_w1_local->dev, "Wait IRQ Timeout\n");
+		return -EBUSY;
+	}
+
+	atomic_set(&amd_axi_w1_local->flag, 0);
+	return 0;
+}
+
+/**
+ * amd_axi_w1_touch_bit() - Performs the touch-bit function - write a 0 or 1 and reads the level.
+ *
+ * @data:	Pointer to device structure
+ * @bit:	The level to write
+ *
+ * Return:	The level read
+ */
+static u8 amd_axi_w1_touch_bit(void *data, u8 bit)
+{
+	struct amd_axi_w1_local *amd_axi_w1_local = data;
+	u8 val = 0;
+	int rc;
+
+	/* Wait for READY signal to be 1 to ensure 1-wire IP is ready */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_READY) == 0) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local,
+							       AXIW1_READY_IRQ_EN);
+		if (rc < 0)
+			return 1; /* Callee doesn't test for error. Return inactive bus state */
+	}
+
+	if (bit)
+		/* Read. Write read Bit command in register 0 */
+		iowrite32(AXIW1_READBIT, amd_axi_w1_local->base_addr + AXIW1_INST_REG);
+	else
+		/* Write. Write tx Bit command in instruction register with bit to transmit */
+		iowrite32(AXIW1_WRITEBIT + (bit & 0x01),
+			  amd_axi_w1_local->base_addr + AXIW1_INST_REG);
+
+	/* Write Go signal and clear control reset signal in control register */
+	iowrite32(AXIW1_GO, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	/* Wait for done signal to be 1 */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_DONE) != 1) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local, AXIW1_DONE_IRQ_EN);
+		if (rc < 0)
+			return 1; /* Callee doesn't test for error. Return inactive bus state */
+	}
+
+	/* If read, Retrieve data from register */
+	if (bit)
+		val = (u8)(ioread32(amd_axi_w1_local->base_addr + AXIW1_DATA_REG) & AXIW1_READDATA);
+
+	/* Clear Go signal in register 1 */
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	return val;
+}
+
+/**
+ * amd_axi_w1_read_byte - Performs the read byte function.
+ *
+ * @data:	Pointer to device structure
+ * Return:	The value read
+ */
+static u8 amd_axi_w1_read_byte(void *data)
+{
+	struct amd_axi_w1_local *amd_axi_w1_local = data;
+	u8 val = 0;
+	int rc;
+
+	/* Wait for READY signal to be 1 to ensure 1-wire IP is ready */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_READY) == 0) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local,
+							       AXIW1_READY_IRQ_EN);
+		if (rc < 0)
+			return 0xFF; /* Return inactive bus state */
+	}
+
+	/* Write read Byte command in instruction register*/
+	iowrite32(AXIW1_READBYTE, amd_axi_w1_local->base_addr + AXIW1_INST_REG);
+
+	/* Write Go signal and clear control reset signal in control register */
+	iowrite32(AXIW1_GO, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	/* Wait for done signal to be 1 */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_DONE) != 1) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local, AXIW1_DONE_IRQ_EN);
+		if (rc < 0)
+			return 0xFF; /* Return inactive bus state */
+	}
+
+	/* Retrieve LSB bit in data register to get RX byte */
+	val = (u8)(ioread32(amd_axi_w1_local->base_addr + AXIW1_DATA_REG) & 0x000000FF);
+
+	/* Clear Go signal in control register */
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	return val;
+}
+
+/**
+ * amd_axi_w1_write_byte - Performs the write byte function.
+ *
+ * @data:	The ds2482 channel pointer
+ * @val:	The value to write
+ */
+static void amd_axi_w1_write_byte(void *data, u8 val)
+{
+	struct amd_axi_w1_local *amd_axi_w1_local = data;
+	int rc;
+
+	/* Wait for READY signal to be 1 to ensure 1-wire IP is ready */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_READY) == 0) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local,
+							       AXIW1_READY_IRQ_EN);
+		if (rc < 0)
+			return;
+	}
+
+	/* Write tx Byte command in instruction register with bit to transmit */
+	iowrite32(AXIW1_WRITEBYTE + val, amd_axi_w1_local->base_addr + AXIW1_INST_REG);
+
+	/* Write Go signal and clear control reset signal in register 1 */
+	iowrite32(AXIW1_GO, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	/* Wait for done signal to be 1 */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_DONE) != 1) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local,
+							       AXIW1_DONE_IRQ_EN);
+		if (rc < 0)
+			return;
+	}
+
+	/* Clear Go signal in control register */
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+}
+
+/**
+ * amd_axi_w1_reset_bus() - Issues a reset bus sequence.
+ *
+ * @data:	the bus host data struct
+ * Return:	0=Device present, 1=No device present or error
+ */
+static u8 amd_axi_w1_reset_bus(void *data)
+{
+	struct amd_axi_w1_local *amd_axi_w1_local = data;
+	u8 val = 0;
+	int rc;
+
+	/* Reset 1-wire Axi IP */
+	iowrite32(AXI_RESET, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	/* Wait for READY signal to be 1 to ensure 1-wire IP is ready */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_READY) == 0) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local,
+							       AXIW1_READY_IRQ_EN);
+		if (rc < 0)
+			return 1; /* Something went wrong with the hardware */
+	}
+	/* Write Initialization command in instruction register */
+	iowrite32(AXIW1_INITPRES, amd_axi_w1_local->base_addr + AXIW1_INST_REG);
+
+	/* Write Go signal and clear control reset signal in register 1 */
+	iowrite32(AXIW1_GO, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	/* Wait for done signal to be 1 */
+	while ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_DONE) != 1) {
+		rc = amd_axi_w1_wait_irq_interruptible_timeout(amd_axi_w1_local, AXIW1_DONE_IRQ_EN);
+		if (rc < 0)
+			return 1; /* Something went wrong with the hardware */
+	}
+	/* Retrieve MSB bit in status register to get failure bit */
+	if ((ioread32(amd_axi_w1_local->base_addr + AXIW1_STAT_REG) & AXIW1_PRESENCE) != 0)
+		val = 1;
+
+	/* Clear Go signal in control register */
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+
+	return val;
+}
+
+/* Reset the 1-wire AXI IP. Put the IP in reset state and clear registers */
+static void amd_axi_w1_reset(struct amd_axi_w1_local *amd_axi_w1_local)
+{
+	iowrite32(AXI_RESET, amd_axi_w1_local->base_addr + AXIW1_CTRL_REG);
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_INST_REG);
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_IRQE_REG);
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_STAT_REG);
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_DATA_REG);
+}
+
+static irqreturn_t amd_axi_w1_irq(int irq, void *lp)
+{
+	struct amd_axi_w1_local *amd_axi_w1_local = lp;
+
+	/* Reset interrupt trigger */
+	iowrite32(AXI_CLEAR, amd_axi_w1_local->base_addr + AXIW1_IRQE_REG);
+
+	atomic_set(&amd_axi_w1_local->flag, 1);
+	wake_up_interruptible(&amd_axi_w1_local->wait_queue);
+
+	return IRQ_HANDLED;
+}
+
+static int amd_axi_w1_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct amd_axi_w1_local *lp;
+	struct clk *clk;
+	u32 ver_major, ver_minor;
+	int val, rc = 0;
+
+	lp = devm_kzalloc(dev, sizeof(*lp), GFP_KERNEL);
+	if (!lp)
+		return -ENOMEM;
+
+	lp->dev = dev;
+	lp->base_addr = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(lp->base_addr))
+		return PTR_ERR(lp->base_addr);
+
+	lp->irq = platform_get_irq(pdev, 0);
+	if (lp->irq < 0)
+		return lp->irq;
+
+	rc = devm_request_irq(dev, lp->irq, &amd_axi_w1_irq, IRQF_TRIGGER_HIGH, DRIVER_NAME, lp);
+	if (rc)
+		return rc;
+
+	/* Initialize wait queue and flag */
+	init_waitqueue_head(&lp->wait_queue);
+
+	clk = devm_clk_get_enabled(dev, NULL);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	/* Verify IP presence in HW */
+	if (ioread32(lp->base_addr + AXIW1_IPID_REG) != AXIW1_IPID) {
+		dev_err(dev, "AMD 1-wire IP not detected in hardware\n");
+		return -ENODEV;
+	}
+
+	/*
+	 * Allow for future driver expansion supporting new hardware features
+	 * This driver currently only supports hardware 1.x, but include logic
+	 * to detect if a potentially incompatible future version is used
+	 * by reading major version ID. It is highly undesirable for new IP versions
+	 * to break the API, but this code will at least allow for graceful failure
+	 * should that happen. Future new features can be enabled by hardware
+	 * incrementing the minor version and augmenting the driver to detect capability
+	 * using the minor version number
+	 */
+	val = ioread32(lp->base_addr + AXIW1_IPVER_REG);
+	ver_major = FIELD_GET(AXIW1_MAJORVER_MASK, val);
+	ver_minor = FIELD_GET(AXIW1_MINORVER_MASK, val);
+
+	if (ver_major != 1) {
+		dev_err(dev, "AMD AXI W1 host version %u.%u is not supported by this driver",
+			ver_major, ver_minor);
+		return -ENODEV;
+	}
+
+	lp->bus_host.data = lp;
+	lp->bus_host.touch_bit = amd_axi_w1_touch_bit;
+	lp->bus_host.read_byte = amd_axi_w1_read_byte;
+	lp->bus_host.write_byte = amd_axi_w1_write_byte;
+	lp->bus_host.reset_bus = amd_axi_w1_reset_bus;
+
+	amd_axi_w1_reset(lp);
+
+	platform_set_drvdata(pdev, lp);
+	rc = w1_add_master_device(&lp->bus_host);
+	if (rc) {
+		dev_err(dev, "Could not add host device\n");
+		return rc;
+	}
+
+	return 0;
+}
+
+static void amd_axi_w1_remove(struct platform_device *pdev)
+{
+	struct amd_axi_w1_local *lp = platform_get_drvdata(pdev);
+
+	w1_remove_master_device(&lp->bus_host);
+}
+
+static const struct of_device_id amd_axi_w1_of_match[] = {
+	{ .compatible = "amd,axi-1wire-host" },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, amd_axi_w1_of_match);
+
+static struct platform_driver amd_axi_w1_driver = {
+	.probe = amd_axi_w1_probe,
+	.remove_new = amd_axi_w1_remove,
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = amd_axi_w1_of_match,
+	},
+};
+module_platform_driver(amd_axi_w1_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kris Chaplin <kris.chaplin@amd.com>");
+MODULE_DESCRIPTION("Driver for AMD AXI 1 Wire IP core");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/slaves/w1_ds28e04.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/slaves/w1_ds28e04.c
@@ -32,7 +32,7 @@
 module_param_named(strong_pullup, w1_strong_pullup, int, 0);
 
 /* enable/disable CRC checking on DS28E04-100 memory accesses */
-static char w1_enable_crccheck = 1;
+static bool w1_enable_crccheck = true;
 
 #define W1_EEPROM_SIZE		512
 #define W1_PAGE_COUNT		16
@@ -339,32 +339,18 @@
 static ssize_t crccheck_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
 {
-	if (put_user(w1_enable_crccheck + 0x30, buf))
-		return -EFAULT;
-
-	return sizeof(w1_enable_crccheck);
+	return sysfs_emit(buf, "%d\n", w1_enable_crccheck);
 }
 
 static ssize_t crccheck_store(struct device *dev, struct device_attribute *attr,
 			      const char *buf, size_t count)
 {
-	char val;
-
-	if (count != 1 || !buf)
-		return -EINVAL;
+	int err = kstrtobool(buf, &w1_enable_crccheck);
 
-	if (get_user(val, buf))
-		return -EFAULT;
+	if (err)
+		return err;
 
-	/* convert to decimal */
-	val = val - 0x30;
-	if (val != 0 && val != 1)
-		return -EINVAL;
-
-	/* set the new value */
-	w1_enable_crccheck = val;
-
-	return sizeof(w1_enable_crccheck);
+	return count;
 }
 
 static DEVICE_ATTR_RW(crccheck);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/slaves/w1_therm.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/slaves/w1_therm.c
@@ -1093,29 +1093,26 @@
 
 			w1_write_8(dev_master, W1_CONVERT_TEMP);
 
-			if (strong_pullup) { /*some device need pullup */
+			if (SLAVE_FEATURES(sl) & W1_THERM_POLL_COMPLETION) {
+				ret = w1_poll_completion(dev_master, W1_POLL_CONVERT_TEMP);
+				if (ret) {
+					dev_dbg(&sl->dev, "%s: Timeout\n", __func__);
+					goto mt_unlock;
+				}
+				mutex_unlock(&dev_master->bus_mutex);
+			} else if (!strong_pullup) { /*no device need pullup */
 				sleep_rem = msleep_interruptible(t_conv);
 				if (sleep_rem != 0) {
 					ret = -EINTR;
 					goto mt_unlock;
 				}
 				mutex_unlock(&dev_master->bus_mutex);
-			} else { /*no device need pullup */
-				if (SLAVE_FEATURES(sl) & W1_THERM_POLL_COMPLETION) {
-					ret = w1_poll_completion(dev_master, W1_POLL_CONVERT_TEMP);
-					if (ret) {
-						dev_dbg(&sl->dev, "%s: Timeout\n", __func__);
-						goto mt_unlock;
-					}
-					mutex_unlock(&dev_master->bus_mutex);
-				} else {
-					/* Fixed delay */
-					mutex_unlock(&dev_master->bus_mutex);
-					sleep_rem = msleep_interruptible(t_conv);
-					if (sleep_rem != 0) {
-						ret = -EINTR;
-						goto dec_refcnt;
-					}
+			} else { /*some device need pullup */
+				mutex_unlock(&dev_master->bus_mutex);
+				sleep_rem = msleep_interruptible(t_conv);
+				if (sleep_rem != 0) {
+					ret = -EINTR;
+					goto dec_refcnt;
 				}
 			}
 			ret = read_scratchpad(sl, info);
@@ -2090,16 +2087,20 @@
 		if (sl->reg_num.id == reg_num->id)
 			seq = i;
 
+		if (w1_reset_bus(sl->master))
+			goto error;
+
+		/* Put the device into chain DONE state */
+		w1_write_8(sl->master, W1_MATCH_ROM);
+		w1_write_block(sl->master, (u8 *)&rn, 8);
 		w1_write_8(sl->master, W1_42_CHAIN);
 		w1_write_8(sl->master, W1_42_CHAIN_DONE);
 		w1_write_8(sl->master, W1_42_CHAIN_DONE_INV);
-		w1_read_block(sl->master, &ack, sizeof(ack));
 
 		/* check for acknowledgment */
 		ack = w1_read_8(sl->master);
 		if (ack != W1_42_SUCCESS_CONFIRM_BYTE)
 			goto error;
-
 	}
 
 	/* Exit from CHAIN state */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/w1.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/w1.c
@@ -1166,6 +1166,8 @@
 	/* remainder if it woke up early */
 	unsigned long jremain = 0;
 
+	atomic_inc(&dev->refcnt);
+
 	for (;;) {
 
 		if (!jremain && dev->search_count) {
@@ -1193,8 +1195,10 @@
 		 */
 		mutex_unlock(&dev->list_mutex);
 
-		if (kthread_should_stop())
+		if (kthread_should_stop()) {
+			__set_current_state(TASK_RUNNING);
 			break;
+		}
 
 		/* Only sleep when the search is active. */
 		if (dev->search_count) {
@@ -1259,10 +1263,10 @@
 
 static void __exit w1_fini(void)
 {
-	struct w1_master *dev;
+	struct w1_master *dev, *n;
 
 	/* Set netlink removal messages and some cleanup */
-	list_for_each_entry(dev, &w1_masters, w1_master_entry)
+	list_for_each_entry_safe(dev, n, &w1_masters, w1_master_entry)
 		__w1_remove_master_device(dev);
 
 	w1_fini_netlink();
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/w1/w1_int.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/w1/w1_int.c
@@ -51,10 +51,9 @@
 	dev->search_count	= w1_search_count;
 	dev->enable_pullup	= w1_enable_pullup;
 
-	/* 1 for w1_process to decrement
-	 * 1 for __w1_remove_master_device to decrement
+	/* For __w1_remove_master_device to decrement
 	 */
-	atomic_set(&dev->refcnt, 2);
+	atomic_set(&dev->refcnt, 1);
 
 	INIT_LIST_HEAD(&dev->slist);
 	INIT_LIST_HEAD(&dev->async_list);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/Kconfig
@@ -1274,7 +1274,7 @@
 config HP_WATCHDOG
 	tristate "HP ProLiant iLO2+ Hardware Watchdog Timer"
 	select WATCHDOG_CORE
-	depends on X86 && PCI
+	depends on (ARM64 || X86) && PCI
 	help
 	  A software monitoring watchdog and NMI handling driver. This driver
 	  will detect lockups and provide a stack trace. This is a driver that
@@ -1284,7 +1284,7 @@
 
 config HPWDT_NMI_DECODING
 	bool "NMI support for the HP ProLiant iLO2+ Hardware Watchdog Timer"
-	depends on HP_WATCHDOG
+	depends on X86 && HP_WATCHDOG
 	default y
 	help
 	  Enables the NMI handler for the watchdog pretimeout NMI and the iLO
@@ -1602,6 +1602,19 @@
 	  To compile this driver as a module, choose M here: the module will be
 	  called nic7018_wdt.
 
+config AAEON_IWMI_WDT
+	tristate "AAEON Watchdog Timer"
+	depends on ASUS_WMI
+	depends on UBUNTU_ODM_DRIVERS
+	select MFD_AAEON
+	help
+	  This is the driver for the hardware watchdog on Single Board
+	  Computers produced by AAEON.Say `Y' here to support its built-in
+	  watchdog timer feature.
+
+	  This driver leverages the ASUS WMI interface to access device
+	  resources.
+
 # M68K Architecture
 
 config M54xx_WATCHDOG
@@ -1679,7 +1692,7 @@
 
 config AR7_WDT
 	tristate "TI AR7 Watchdog Timer"
-	depends on AR7 || (MIPS && COMPILE_TEST)
+	depends on AR7 || (MIPS && 32BIT && COMPILE_TEST)
 	help
 	  Hardware driver for the TI AR7 Watchdog Timer.
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/Makefile
@@ -144,6 +144,7 @@
 obj-$(CONFIG_NIC7018_WDT) += nic7018_wdt.o
 obj-$(CONFIG_MLX_WDT) += mlx_wdt.o
 obj-$(CONFIG_KEEMBAY_WATCHDOG) += keembay_wdt.o
+obj-$(CONFIG_AAEON_IWMI_WDT) += wdt_aaeon.o
 
 # M68K Architecture
 obj-$(CONFIG_M54xx_WATCHDOG) += m54xx_wdt.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/armada_37xx_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/armada_37xx_wdt.c
@@ -274,6 +274,8 @@
 	if (!res)
 		return -ENODEV;
 	dev->reg = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+	if (!dev->reg)
+		return -ENOMEM;
 
 	/* init clock */
 	dev->clk = devm_clk_get(&pdev->dev, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/at91sam9_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/at91sam9_wdt.c
@@ -206,10 +206,9 @@
 			 "min heartbeat and max heartbeat might be too close for the system to handle it correctly\n");
 
 	if ((tmp & AT91_WDT_WDFIEN) && wdt->irq) {
-		err = request_irq(wdt->irq, wdt_interrupt,
-				  IRQF_SHARED | IRQF_IRQPOLL |
-				  IRQF_NO_SUSPEND,
-				  pdev->name, wdt);
+		err = devm_request_irq(dev, wdt->irq, wdt_interrupt,
+				       IRQF_SHARED | IRQF_IRQPOLL | IRQF_NO_SUSPEND,
+				       pdev->name, wdt);
 		if (err)
 			return err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/bcm2835_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/bcm2835_wdt.c
@@ -42,6 +42,7 @@
 
 #define SECS_TO_WDOG_TICKS(x) ((x) << 16)
 #define WDOG_TICKS_TO_SECS(x) ((x) >> 16)
+#define WDOG_TICKS_TO_MSECS(x) ((x) * 1000 >> 16)
 
 struct bcm2835_wdt {
 	void __iomem		*base;
@@ -140,7 +141,7 @@
 	.info =		&bcm2835_wdt_info,
 	.ops =		&bcm2835_wdt_ops,
 	.min_timeout =	1,
-	.max_timeout =	WDOG_TICKS_TO_SECS(PM_WDOG_TIME_SET),
+	.max_hw_heartbeat_ms =	WDOG_TICKS_TO_MSECS(PM_WDOG_TIME_SET),
 	.timeout =	WDOG_TICKS_TO_SECS(PM_WDOG_TIME_SET),
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/bd9576_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/bd9576_wdt.c
@@ -9,8 +9,8 @@
 #include <linux/gpio/consumer.h>
 #include <linux/mfd/rohm-bd957x.h>
 #include <linux/module.h>
-#include <linux/of.h>
 #include <linux/platform_device.h>
+#include <linux/property.h>
 #include <linux/regmap.h>
 #include <linux/watchdog.h>
 
@@ -29,7 +29,6 @@
 	struct gpio_desc	*gpiod_en;
 	struct device		*dev;
 	struct regmap		*regmap;
-	bool			always_running;
 	struct watchdog_device	wdd;
 };
 
@@ -62,10 +61,7 @@
 {
 	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
 
-	if (!priv->always_running)
-		bd9576_wdt_disable(priv);
-	else
-		set_bit(WDOG_HW_RUNNING, &wdd->status);
+	bd9576_wdt_disable(priv);
 
 	return 0;
 }
@@ -202,10 +198,10 @@
 static int bd9576_wdt_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-	struct device_node *np = dev->parent->of_node;
 	struct bd9576_wdt_priv *priv;
 	u32 hw_margin[2];
 	u32 hw_margin_max = BD957X_WDT_DEFAULT_MARGIN, hw_margin_min = 0;
+	int count;
 	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -221,41 +217,49 @@
 		return -ENODEV;
 	}
 
-	priv->gpiod_en = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
-						     "rohm,watchdog-enable-gpios",
-						     0, GPIOD_OUT_LOW,
-						     "watchdog-enable");
+	priv->gpiod_en = devm_fwnode_gpiod_get(dev, dev_fwnode(dev->parent),
+					       "rohm,watchdog-enable",
+					       GPIOD_OUT_LOW,
+					       "watchdog-enable");
 	if (IS_ERR(priv->gpiod_en))
 		return dev_err_probe(dev, PTR_ERR(priv->gpiod_en),
 			      "getting watchdog-enable GPIO failed\n");
 
-	priv->gpiod_ping = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
-						     "rohm,watchdog-ping-gpios",
-						     0, GPIOD_OUT_LOW,
-						     "watchdog-ping");
+	priv->gpiod_ping = devm_fwnode_gpiod_get(dev, dev_fwnode(dev->parent),
+						 "rohm,watchdog-ping",
+						 GPIOD_OUT_LOW,
+						 "watchdog-ping");
 	if (IS_ERR(priv->gpiod_ping))
 		return dev_err_probe(dev, PTR_ERR(priv->gpiod_ping),
 				     "getting watchdog-ping GPIO failed\n");
 
-	ret = of_property_read_variable_u32_array(np, "rohm,hw-timeout-ms",
-						  &hw_margin[0], 1, 2);
-	if (ret < 0 && ret != -EINVAL)
-		return ret;
+	count = device_property_count_u32(dev->parent, "rohm,hw-timeout-ms");
+	if (count < 0 && count != -EINVAL)
+		return count;
+
+	if (count > 0) {
+		if (count > ARRAY_SIZE(hw_margin))
+			return -EINVAL;
+
+		ret = device_property_read_u32_array(dev->parent,
+						     "rohm,hw-timeout-ms",
+						     hw_margin, count);
+		if (ret < 0)
+			return ret;
 
-	if (ret == 1)
-		hw_margin_max = hw_margin[0];
+		if (count == 1)
+			hw_margin_max = hw_margin[0];
 
-	if (ret == 2) {
-		hw_margin_max = hw_margin[1];
-		hw_margin_min = hw_margin[0];
+		if (count == 2) {
+			hw_margin_max = hw_margin[1];
+			hw_margin_min = hw_margin[0];
+		}
 	}
 
 	ret = bd957x_set_wdt_mode(priv, hw_margin_max, hw_margin_min);
 	if (ret)
 		return ret;
 
-	priv->always_running = of_property_read_bool(np, "always-running");
-
 	watchdog_set_drvdata(&priv->wdd, priv);
 
 	priv->wdd.info			= &bd957x_wdt_ident;
@@ -270,9 +274,6 @@
 
 	watchdog_stop_on_reboot(&priv->wdd);
 
-	if (priv->always_running)
-		bd9576_wdt_start(&priv->wdd);
-
 	return devm_watchdog_register_device(dev, &priv->wdd);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/cpu5wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/cpu5wdt.c
@@ -252,7 +252,7 @@
 	if (cpu5wdt_device.queue) {
 		cpu5wdt_device.queue = 0;
 		wait_for_completion(&cpu5wdt_device.stop);
-		del_timer(&cpu5wdt_device.timer);
+		timer_shutdown_sync(&cpu5wdt_device.timer);
 	}
 
 	misc_deregister(&cpu5wdt_misc);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/diag288_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/diag288_wdt.c
@@ -86,7 +86,7 @@
 		"1:\n"
 		EX_TABLE(0b, 1b)
 		: "+d" (err) : "d"(__func), "d"(__timeout),
-		  "d"(__action), "d"(__len) : "1", "cc");
+		  "d"(__action), "d"(__len) : "1", "cc", "memory");
 	return err;
 }
 
@@ -268,12 +268,21 @@
 	char ebc_begin[] = {
 		194, 197, 199, 201, 213
 	};
+	char *ebc_cmd;
 
 	watchdog_set_nowayout(&wdt_dev, nowayout_info);
 
 	if (MACHINE_IS_VM) {
-		if (__diag288_vm(WDT_FUNC_INIT, 15,
-				 ebc_begin, sizeof(ebc_begin)) != 0) {
+		ebc_cmd = kmalloc(sizeof(ebc_begin), GFP_KERNEL);
+		if (!ebc_cmd) {
+			pr_err("The watchdog cannot be initialized\n");
+			return -ENOMEM;
+		}
+		memcpy(ebc_cmd, ebc_begin, sizeof(ebc_begin));
+		ret = __diag288_vm(WDT_FUNC_INIT, 15,
+				   ebc_cmd, sizeof(ebc_begin));
+		kfree(ebc_cmd);
+		if (ret != 0) {
 			pr_err("The watchdog cannot be initialized\n");
 			return -EINVAL;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/dw_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/dw_wdt.c
@@ -637,7 +637,7 @@
 
 	ret = dw_wdt_init_timeouts(dw_wdt, dev);
 	if (ret)
-		goto out_disable_clk;
+		goto out_assert_rst;
 
 	wdd = &dw_wdt->wdd;
 	wdd->ops = &dw_wdt_ops;
@@ -668,12 +668,15 @@
 
 	ret = watchdog_register_device(wdd);
 	if (ret)
-		goto out_disable_pclk;
+		goto out_assert_rst;
 
 	dw_wdt_dbgfs_init(dw_wdt);
 
 	return 0;
 
+out_assert_rst:
+	reset_control_assert(dw_wdt->rst);
+
 out_disable_pclk:
 	clk_disable_unprepare(dw_wdt->pclk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/f71808e_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/f71808e_wdt.c
@@ -54,6 +54,7 @@
 #define SIO_F81803_ID		0x1210	/* Chipset ID */
 #define SIO_F81865_ID		0x0704	/* Chipset ID */
 #define SIO_F81866_ID		0x1010	/* Chipset ID */
+#define SIO_F81966_ID		0x1502  /* F81804 chipset ID, same for f81966 */
 
 #define F71808FG_REG_WDO_CONF		0xf0
 #define F71808FG_REG_WDT_CONF		0xf5
@@ -111,7 +112,7 @@
 	" given initial timeout. Zero (default) disables this feature.");
 
 enum chips { f71808fg, f71858fg, f71862fg, f71868, f71869, f71882fg, f71889fg,
-	     f81803, f81865, f81866};
+	     f81803, f81865, f81866, f81966};
 
 static const char *f71808e_names[] = {
 	"f71808fg",
@@ -124,6 +125,7 @@
 	"f81803",
 	"f81865",
 	"f81866",
+	"f81966"
 };
 
 /* Super-I/O Function prototypes */
@@ -228,15 +230,17 @@
 
 	mutex_lock(&watchdog.lock);
 
-	watchdog.timeout = timeout;
 	if (timeout > 0xff) {
 		watchdog.timer_val = DIV_ROUND_UP(timeout, 60);
 		watchdog.minutes_mode = true;
+		timeout = watchdog.timer_val * 60;
 	} else {
 		watchdog.timer_val = timeout;
 		watchdog.minutes_mode = false;
 	}
 
+	watchdog.timeout = timeout;
+
 	mutex_unlock(&watchdog.lock);
 
 	return 0;
@@ -371,6 +375,7 @@
 		break;
 
 	case f81866:
+	case f81966:
 		/*
 		 * GPIO1 Control Register when 27h BIT3:2 = 01 & BIT0 = 0.
 		 * The PIN 70(GPIO15/WDTRST) is controlled by 2Ch:
@@ -397,7 +402,7 @@
 	superio_select(watchdog.sioaddr, SIO_F71808FG_LD_WDT);
 	superio_set_bit(watchdog.sioaddr, SIO_REG_ENABLE, 0);
 
-	if (watchdog.type == f81865 || watchdog.type == f81866)
+	if (watchdog.type == f81865 || watchdog.type == f81866 || watchdog.type == f81966)
 		superio_set_bit(watchdog.sioaddr, F81865_REG_WDO_CONF,
 				F81865_FLAG_WDOUT_EN);
 	else
@@ -820,6 +825,9 @@
 	case SIO_F81866_ID:
 		watchdog.type = f81866;
 		break;
+	case SIO_F81966_ID:
+		watchdog.type = f81966;
+		break;
 	default:
 		pr_info("Unrecognized Fintek device: %04x\n",
 			(unsigned int)devid);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/hpwdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/hpwdt.c
@@ -20,7 +20,9 @@
 #include <linux/pci_ids.h>
 #include <linux/types.h>
 #include <linux/watchdog.h>
+#ifdef CONFIG_HPWDT_NMI_DECODING
 #include <asm/nmi.h>
+#endif
 #include <linux/crash_dump.h>
 
 #define HPWDT_VERSION			"2.0.4"
@@ -176,7 +178,7 @@
 		"3. OA Forward Progress Log\n"
 		"4. iLO Event Log";
 
-	if (ilo5 && ulReason == NMI_UNKNOWN && !mynmi)
+	if (ulReason == NMI_UNKNOWN && !mynmi)
 		return NMI_DONE;
 
 	if (ilo5 && !pretimeout && !mynmi)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/iTCO_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/iTCO_wdt.c
@@ -82,6 +82,13 @@
 #define TCO2_CNT(p)	(TCOBASE(p) + 0x0a) /* TCO2 Control Register	*/
 #define TCOv2_TMR(p)	(TCOBASE(p) + 0x12) /* TCOv2 Timer Initial Value*/
 
+/*
+ * NMI_NOW is bit 8 of TCO1_CNT register
+ * Read/Write
+ * This bit is implemented as RW but has no effect on HW.
+ */
+#define NMI_NOW		BIT(8)
+
 /* internal variables */
 struct iTCO_wdt_private {
 	struct watchdog_device wddev;
@@ -220,13 +227,23 @@
 	struct iTCO_wdt_private *p = priv;
 	u16 val, newval;
 
-	val = inw(TCO1_CNT(p));
+	/*
+	 * writing back 1b1 to NMI_NOW of TCO1_CNT register
+	 * causes NMI_NOW bit inversion what consequently does
+	 * not allow to perform the register's value comparison
+	 * properly.
+	 *
+	 * NMI_NOW bit masking for TCO1_CNT register values
+	 * helps to avoid possible NMI_NOW bit inversions on
+	 * following write operation.
+	 */
+	val = inw(TCO1_CNT(p)) & ~NMI_NOW;
 	if (set)
 		val |= BIT(0);
 	else
 		val &= ~BIT(0);
 	outw(val, TCO1_CNT(p));
-	newval = inw(TCO1_CNT(p));
+	newval = inw(TCO1_CNT(p)) & ~NMI_NOW;
 
 	/* make sure the update is successful */
 	return val != newval ? -EIO : 0;
@@ -424,6 +441,20 @@
 	return time_left;
 }
 
+/* Returns true if the watchdog was running */
+static bool iTCO_wdt_set_running(struct iTCO_wdt_private *p)
+{
+	u16 val;
+
+	/* Bit 11: TCO Timer Halt -> 0 = The TCO timer is enabled */
+	val = inw(TCO1_CNT(p));
+	if (!(val & BIT(11))) {
+		set_bit(WDOG_HW_RUNNING, &p->wddev.status);
+		return true;
+	}
+	return false;
+}
+
 /*
  *	Kernel Interfaces
  */
@@ -512,9 +543,6 @@
 		return -ENODEV;	/* Cannot reset NO_REBOOT bit */
 	}
 
-	/* Set the NO_REBOOT bit to prevent later reboots, just for sure */
-	p->update_no_reboot_bit(p->no_reboot_priv, true);
-
 	if (turn_SMI_watchdog_clear_off >= p->iTCO_version) {
 		/*
 		 * Bit 13: TCO_EN -> 0
@@ -566,8 +594,13 @@
 	watchdog_set_drvdata(&p->wddev, p);
 	platform_set_drvdata(pdev, p);
 
-	/* Make sure the watchdog is not running */
-	iTCO_wdt_stop(&p->wddev);
+	if (!iTCO_wdt_set_running(p)) {
+		/*
+		 * If the watchdog was not running set NO_REBOOT now to
+		 * prevent later reboots.
+		 */
+		p->update_no_reboot_bit(p->no_reboot_priv, true);
+	}
 
 	/* Check that the heartbeat value is within it's range;
 	   if not reset to the default */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/imx_sc_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/imx_sc_wdt.c
@@ -213,29 +213,6 @@
 	return devm_watchdog_register_device(dev, wdog);
 }
 
-static int __maybe_unused imx_sc_wdt_suspend(struct device *dev)
-{
-	struct imx_sc_wdt_device *imx_sc_wdd = dev_get_drvdata(dev);
-
-	if (watchdog_active(&imx_sc_wdd->wdd))
-		imx_sc_wdt_stop(&imx_sc_wdd->wdd);
-
-	return 0;
-}
-
-static int __maybe_unused imx_sc_wdt_resume(struct device *dev)
-{
-	struct imx_sc_wdt_device *imx_sc_wdd = dev_get_drvdata(dev);
-
-	if (watchdog_active(&imx_sc_wdd->wdd))
-		imx_sc_wdt_start(&imx_sc_wdd->wdd);
-
-	return 0;
-}
-
-static SIMPLE_DEV_PM_OPS(imx_sc_wdt_pm_ops,
-			 imx_sc_wdt_suspend, imx_sc_wdt_resume);
-
 static const struct of_device_id imx_sc_wdt_dt_ids[] = {
 	{ .compatible = "fsl,imx-sc-wdt", },
 	{ /* sentinel */ }
@@ -247,7 +224,6 @@
 	.driver		= {
 		.name	= "imx-sc-wdt",
 		.of_match_table = imx_sc_wdt_dt_ids,
-		.pm	= &imx_sc_wdt_pm_ops,
 	},
 };
 module_platform_driver(imx_sc_wdt_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/intel-mid_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/intel-mid_wdt.c
@@ -203,3 +203,4 @@
 MODULE_AUTHOR("David Cohen <david.a.cohen@linux.intel.com>");
 MODULE_DESCRIPTION("Watchdog Driver for Intel MID platform");
 MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:intel_mid_wdt");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/it87_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/it87_wdt.c
@@ -20,6 +20,8 @@
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
+#include <linux/bits.h>
+#include <linux/dmi.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
@@ -40,6 +42,7 @@
 #define VAL		0x2f
 
 /* Logical device Numbers LDN */
+#define EC		0x04
 #define GPIO		0x07
 
 /* Configuration Registers and Functions */
@@ -71,6 +74,12 @@
 #define IT8784_ID	0x8784
 #define IT8786_ID	0x8786
 
+/* Environment Controller Configuration Registers LDN=0x04 */
+#define SCR1		0xfa
+
+/* Environment Controller Bits SCR1 */
+#define WDT_PWRGD	0x20
+
 /* GPIO Configuration Registers LDN=0x07 */
 #define WDTCTRL		0x71
 #define WDTCFG		0x72
@@ -233,6 +242,21 @@
 	return ret;
 }
 
+enum {
+	IT87_WDT_OUTPUT_THROUGH_PWRGD	= BIT(0),
+};
+
+static const struct dmi_system_id it87_quirks[] = {
+	{
+		/* Qotom Q30900P (IT8786) */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_BOARD_NAME, "QCML04"),
+		},
+		.driver_data = (void *)IT87_WDT_OUTPUT_THROUGH_PWRGD,
+	},
+	{}
+};
+
 static const struct watchdog_info ident = {
 	.options = WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING,
 	.firmware_version = 1,
@@ -254,7 +278,10 @@
 
 static int __init it87_wdt_init(void)
 {
+	const struct dmi_system_id *dmi_id;
 	u8  chip_rev;
+	u8 ctrl;
+	int quirks = 0;
 	int rc;
 
 	rc = superio_enter();
@@ -265,6 +292,10 @@
 	chip_rev  = superio_inb(CHIPREV) & 0x0f;
 	superio_exit();
 
+	dmi_id = dmi_first_match(it87_quirks);
+	if (dmi_id)
+		quirks = (long)dmi_id->driver_data;
+
 	switch (chip_type) {
 	case IT8702_ID:
 		max_units = 255;
@@ -313,7 +344,27 @@
 
 	superio_select(GPIO);
 	superio_outb(WDT_TOV1, WDTCFG);
-	superio_outb(0x00, WDTCTRL);
+
+	switch (chip_type) {
+	case IT8784_ID:
+	case IT8786_ID:
+		ctrl = superio_inb(WDTCTRL);
+		ctrl &= 0x08;
+		superio_outb(ctrl, WDTCTRL);
+		break;
+	default:
+		superio_outb(0x00, WDTCTRL);
+	}
+
+	if (quirks & IT87_WDT_OUTPUT_THROUGH_PWRGD) {
+		superio_select(EC);
+		ctrl = superio_inb(SCR1);
+		if (!(ctrl & WDT_PWRGD)) {
+			ctrl |= WDT_PWRGD;
+			superio_outb(ctrl, SCR1);
+		}
+	}
+
 	superio_exit();
 
 	if (timeout < 1 || timeout > max_units * 60) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/menz69_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/menz69_wdt.c
@@ -98,14 +98,6 @@
 	.set_timeout = men_z069_wdt_set_timeout,
 };
 
-static struct watchdog_device men_z069_wdt = {
-	.info = &men_z069_info,
-	.ops = &men_z069_ops,
-	.timeout = MEN_Z069_DEFAULT_TIMEOUT,
-	.min_timeout = 1,
-	.max_timeout = MEN_Z069_WDT_COUNTER_MAX / MEN_Z069_TIMER_FREQ,
-};
-
 static int men_z069_probe(struct mcb_device *dev,
 			  const struct mcb_device_id *id)
 {
@@ -125,15 +117,19 @@
 		goto release_mem;
 
 	drv->mem = mem;
+	drv->wdt.info = &men_z069_info;
+	drv->wdt.ops = &men_z069_ops;
+	drv->wdt.timeout = MEN_Z069_DEFAULT_TIMEOUT;
+	drv->wdt.min_timeout = 1;
+	drv->wdt.max_timeout = MEN_Z069_WDT_COUNTER_MAX / MEN_Z069_TIMER_FREQ;
 
-	drv->wdt = men_z069_wdt;
 	watchdog_init_timeout(&drv->wdt, 0, &dev->dev);
 	watchdog_set_nowayout(&drv->wdt, nowayout);
 	watchdog_set_drvdata(&drv->wdt, drv);
 	drv->wdt.parent = &dev->dev;
 	mcb_set_drvdata(dev, drv);
 
-	return watchdog_register_device(&men_z069_wdt);
+	return watchdog_register_device(&drv->wdt);
 
 release_mem:
 	mcb_release_mem(mem);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/mtk_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/mtk_wdt.c
@@ -164,9 +164,15 @@
 {
 	struct mtk_wdt_dev *mtk_wdt = watchdog_get_drvdata(wdt_dev);
 	void __iomem *wdt_base;
+	u32 reg;
 
 	wdt_base = mtk_wdt->wdt_base;
 
+	/* Enable reset in order to issue a system reset instead of an IRQ */
+	reg = readl(wdt_base + WDT_MODE);
+	reg &= ~WDT_MODE_IRQ_EN;
+	writel(reg | WDT_MODE_KEY, wdt_base + WDT_MODE);
+
 	while (1) {
 		writel(WDT_SWRST_KEY, wdt_base + WDT_SWRST);
 		mdelay(5);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/of_xilinx_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/of_xilinx_wdt.c
@@ -2,7 +2,7 @@
 /*
  * Watchdog Device Driver for Xilinx axi/xps_timebase_wdt
  *
- * (C) Copyright 2013 - 2014 Xilinx, Inc.
+ * (C) Copyright 2013 - 2020 Xilinx, Inc.
  * (C) Copyright 2011 (Alejandro Cabrera <aldaya@gmail.com>)
  */
 
@@ -18,6 +18,11 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_address.h>
+#include <linux/interrupt.h>
+
+#define XWT_WWDT_DEFAULT_TIMEOUT	10
+#define XWT_WWDT_MIN_TIMEOUT		1
+#define XWT_WWDT_MAX_TIMEOUT		42
 
 /* Register offsets for the Wdt device */
 #define XWT_TWCSR0_OFFSET   0x0 /* Control/Status Register0 */
@@ -36,14 +41,59 @@
 #define XWT_MAX_SELFTEST_LOOP_COUNT 0x00010000
 #define XWT_TIMER_FAILED            0xFFFFFFFF
 
+/* Register offsets for the WWdt device */
+#define XWT_WWDT_MWR_OFFSET	0x00
+#define XWT_WWDT_ESR_OFFSET	0x04
+#define XWT_WWDT_FCR_OFFSET	0x08
+#define XWT_WWDT_FWR_OFFSET	0x0c
+#define XWT_WWDT_SWR_OFFSET	0x10
+
+/* Master Write Control Register Masks */
+#define XWT_WWDT_MWR_MASK	BIT(0)
+
+/* Enable and Status Register Masks */
+#define XWT_WWDT_ESR_WINT_MASK	BIT(16)
+#define XWT_WWDT_ESR_WSW_MASK	BIT(8)
+#define XWT_WWDT_ESR_WEN_MASK	BIT(0)
+
+/* Function control Register Masks */
+#define XWT_WWDT_SBC_MASK	0xFF00
+#define XWT_WWDT_SBC_SHIFT	16
+#define XWT_WWDT_BSS_MASK	0xC0
+
 #define WATCHDOG_NAME     "Xilinx Watchdog"
 
+static int wdt_timeout;
+
+module_param(wdt_timeout, int, 0644);
+MODULE_PARM_DESC(wdt_timeout,
+		 "Watchdog time in seconds. (default="
+		 __MODULE_STRING(XWT_WWDT_DEFAULT_TIMEOUT) ")");
+
+/**
+ * enum xwdt_ip_type - WDT IP type.
+ *
+ * @XWDT_WDT: Soft wdt ip.
+ * @XWDT_WWDT: Window wdt ip.
+ */
+enum xwdt_ip_type {
+	XWDT_WDT = 0,
+	XWDT_WWDT = 1,
+};
+
+struct xwdt_devtype_data {
+	enum xwdt_ip_type wdttype;
+	const struct watchdog_ops *xwdt_ops;
+	const struct watchdog_info *xwdt_info;
+};
+
 struct xwdt_device {
 	void __iomem *base;
 	u32 wdt_interval;
 	spinlock_t spinlock; /* spinlock for register handling */
 	struct watchdog_device xilinx_wdt_wdd;
 	struct clk		*clk;
+	int irq;
 };
 
 static int xilinx_wdt_start(struct watchdog_device *wdd)
@@ -129,6 +179,220 @@
 	.ping = xilinx_wdt_keepalive,
 };
 
+static int is_wwdt_in_closed_window(struct watchdog_device *wdd)
+{
+	u32 control_status_reg;
+	struct xwdt_device *xdev = watchdog_get_drvdata(wdd);
+
+	control_status_reg = ioread32(xdev->base + XWT_WWDT_ESR_OFFSET);
+	if (control_status_reg & XWT_WWDT_ESR_WEN_MASK)
+		if (!(control_status_reg & XWT_WWDT_ESR_WSW_MASK))
+			return 0;
+
+	return 1;
+}
+
+static int xilinx_wwdt_start(struct watchdog_device *wdd)
+{
+	int ret;
+	u32 control_status_reg, fcr;
+	u64 time_out, pre_timeout, count;
+	struct xwdt_device *xdev = watchdog_get_drvdata(wdd);
+	struct watchdog_device *xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
+
+	count = clk_get_rate(xdev->clk);
+	if (!count)
+		return -EINVAL;
+
+	/* Calculate timeout count */
+	pre_timeout = count * wdd->pretimeout;
+	time_out = count * wdd->timeout;
+	if (!watchdog_active(xilinx_wdt_wdd)) {
+		ret  = clk_enable(xdev->clk);
+		if (ret) {
+			dev_err(wdd->parent, "Failed to enable clock\n");
+			return ret;
+		}
+	}
+
+	spin_lock(&xdev->spinlock);
+	iowrite32(XWT_WWDT_MWR_MASK, xdev->base + XWT_WWDT_MWR_OFFSET);
+	iowrite32(~(u32)XWT_WWDT_ESR_WEN_MASK,
+		  xdev->base + XWT_WWDT_ESR_OFFSET);
+
+	if (pre_timeout) {
+		iowrite32((u32)(time_out - pre_timeout),
+			  xdev->base + XWT_WWDT_FWR_OFFSET);
+		iowrite32((u32)pre_timeout, xdev->base + XWT_WWDT_SWR_OFFSET);
+		fcr = ioread32(xdev->base + XWT_WWDT_SWR_OFFSET);
+		fcr = (fcr >> XWT_WWDT_SBC_SHIFT) & XWT_WWDT_SBC_MASK;
+		fcr = fcr | XWT_WWDT_BSS_MASK;
+		iowrite32(fcr, xdev->base + XWT_WWDT_FCR_OFFSET);
+	} else {
+		iowrite32((u32)pre_timeout,
+			  xdev->base + XWT_WWDT_FWR_OFFSET);
+		iowrite32((u32)time_out, xdev->base + XWT_WWDT_SWR_OFFSET);
+		iowrite32(0x0, xdev->base + XWT_WWDT_FCR_OFFSET);
+	}
+
+	/* Enable the window watchdog timer */
+	control_status_reg = ioread32(xdev->base + XWT_WWDT_ESR_OFFSET);
+	control_status_reg |= XWT_WWDT_ESR_WEN_MASK;
+	iowrite32(control_status_reg, xdev->base + XWT_WWDT_ESR_OFFSET);
+
+	spin_unlock(&xdev->spinlock);
+
+	dev_dbg(xilinx_wdt_wdd->parent, "Watchdog Started!\n");
+
+	return 0;
+}
+
+static int xilinx_wwdt_stop(struct watchdog_device *wdd)
+{
+	struct xwdt_device *xdev = watchdog_get_drvdata(wdd);
+	struct watchdog_device *xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
+
+	if (!is_wwdt_in_closed_window(wdd)) {
+		dev_warn(xilinx_wdt_wdd->parent, "timer in closed window");
+		return -EINVAL;
+	}
+
+	spin_lock(&xdev->spinlock);
+
+	iowrite32(XWT_WWDT_MWR_MASK, xdev->base + XWT_WWDT_MWR_OFFSET);
+	/* Disable the Window watchdog timer */
+	iowrite32(~(u32)XWT_WWDT_ESR_WEN_MASK,
+		  xdev->base + XWT_WWDT_ESR_OFFSET);
+
+	spin_unlock(&xdev->spinlock);
+
+	if (watchdog_active(xilinx_wdt_wdd))
+		clk_disable(xdev->clk);
+
+	dev_dbg(xilinx_wdt_wdd->parent, "Watchdog Stopped!\n");
+
+	return 0;
+}
+
+static int xilinx_wwdt_keepalive(struct watchdog_device *wdd)
+{
+	u32 control_status_reg;
+	struct xwdt_device *xdev = watchdog_get_drvdata(wdd);
+
+	/* Refresh in open window is ignored */
+	if (!is_wwdt_in_closed_window(wdd))
+		return 0;
+
+	spin_lock(&xdev->spinlock);
+
+	iowrite32(XWT_WWDT_MWR_MASK, xdev->base + XWT_WWDT_MWR_OFFSET);
+	control_status_reg = ioread32(xdev->base + XWT_WWDT_ESR_OFFSET);
+	control_status_reg |= XWT_WWDT_ESR_WINT_MASK;
+	control_status_reg &= ~XWT_WWDT_ESR_WSW_MASK;
+	iowrite32(control_status_reg, xdev->base + XWT_WWDT_ESR_OFFSET);
+	control_status_reg = ioread32(xdev->base + XWT_WWDT_ESR_OFFSET);
+	control_status_reg |= XWT_WWDT_ESR_WSW_MASK;
+	iowrite32(control_status_reg, xdev->base + XWT_WWDT_ESR_OFFSET);
+
+	spin_unlock(&xdev->spinlock);
+
+	return 0;
+}
+
+static int xilinx_wwdt_set_timeout(struct watchdog_device *wdd,
+				   unsigned int new_time)
+{
+	u32 ret = 0;
+	struct xwdt_device *xdev = watchdog_get_drvdata(wdd);
+	struct watchdog_device *xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
+
+	if (!is_wwdt_in_closed_window(wdd)) {
+		dev_warn(xilinx_wdt_wdd->parent, "timer in closed window");
+		return -EINVAL;
+	}
+
+	if (new_time < XWT_WWDT_MIN_TIMEOUT ||
+	    new_time > XWT_WWDT_MAX_TIMEOUT) {
+		dev_warn(xilinx_wdt_wdd->parent,
+			 "timeout value must be %d<=x<=%d, using %d\n",
+				XWT_WWDT_MIN_TIMEOUT,
+				XWT_WWDT_MAX_TIMEOUT, new_time);
+		return -EINVAL;
+	}
+
+	wdd->timeout = new_time;
+	wdd->pretimeout = 0;
+
+	if (watchdog_active(xilinx_wdt_wdd)) {
+		ret = xilinx_wwdt_start(wdd);
+		if (ret)
+			dev_dbg(xilinx_wdt_wdd->parent, "timer start failed");
+	}
+
+	return 0;
+}
+
+static int xilinx_wwdt_set_pretimeout(struct watchdog_device *wdd,
+				      u32 new_pretimeout)
+{
+	u32 ret = 0;
+	struct xwdt_device *xdev = watchdog_get_drvdata(wdd);
+	struct watchdog_device *xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
+
+	if (!is_wwdt_in_closed_window(wdd)) {
+		dev_warn(xilinx_wdt_wdd->parent, "timer in closed window");
+		return -EINVAL;
+	}
+
+	if (new_pretimeout < wdd->min_timeout ||
+	    new_pretimeout >= wdd->timeout)
+		return -EINVAL;
+
+	wdd->pretimeout = new_pretimeout;
+
+	if (watchdog_active(xilinx_wdt_wdd)) {
+		ret = xilinx_wwdt_start(wdd);
+		if (ret)
+			dev_dbg(xilinx_wdt_wdd->parent, "timer start failed");
+	}
+
+	return 0;
+}
+
+static irqreturn_t xilinx_wwdt_isr(int irq, void *wdog_arg)
+{
+	struct xwdt_device *xdev = wdog_arg;
+
+	watchdog_notify_pretimeout(&xdev->xilinx_wdt_wdd);
+	return IRQ_HANDLED;
+}
+
+static const struct watchdog_info xilinx_wwdt_ident = {
+	.options =  WDIOF_MAGICCLOSE |
+		WDIOF_KEEPALIVEPING |
+		WDIOF_SETTIMEOUT,
+	.firmware_version = 1,
+	.identity = "xlnx_wwdt watchdog",
+};
+
+static const struct watchdog_info xilinx_wwdt_pretimeout_ident = {
+	.options = WDIOF_MAGICCLOSE |
+		   WDIOF_KEEPALIVEPING |
+		   WDIOF_PRETIMEOUT |
+		   WDIOF_SETTIMEOUT,
+	.firmware_version = 1,
+	.identity = "xlnx_wwdt watchdog",
+};
+
+static const struct watchdog_ops xilinx_wwdt_ops = {
+	.owner = THIS_MODULE,
+	.start = xilinx_wwdt_start,
+	.stop = xilinx_wwdt_stop,
+	.ping = xilinx_wwdt_keepalive,
+	.set_timeout = xilinx_wwdt_set_timeout,
+	.set_pretimeout = xilinx_wwdt_set_pretimeout,
+};
+
 static u32 xwdt_selftest(struct xwdt_device *xdev)
 {
 	int i;
@@ -159,39 +423,82 @@
 	clk_disable_unprepare(data);
 }
 
+static const struct xwdt_devtype_data xwdt_wdt_data = {
+	.wdttype = XWDT_WDT,
+	.xwdt_info = &xilinx_wdt_ident,
+	.xwdt_ops = &xilinx_wdt_ops,
+};
+
+static const struct xwdt_devtype_data xwdt_wwdt_data = {
+	.wdttype = XWDT_WWDT,
+	.xwdt_info = &xilinx_wwdt_ident,
+	.xwdt_ops = &xilinx_wwdt_ops,
+};
+
+static const struct of_device_id xwdt_of_match[] = {
+	{ .compatible = "xlnx,xps-timebase-wdt-1.00.a",
+		.data = &xwdt_wdt_data },
+	{ .compatible = "xlnx,xps-timebase-wdt-1.01.a",
+		.data = &xwdt_wdt_data },
+	{ .compatible = "xlnx,versal-wwdt-1.0",
+		.data = &xwdt_wwdt_data },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xwdt_of_match);
+
 static int xwdt_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	int rc;
-	u32 pfreq = 0, enable_once = 0;
+	u32 pfreq = 0, enable_once = 0, pre_timeout = 0;
 	struct xwdt_device *xdev;
 	struct watchdog_device *xilinx_wdt_wdd;
+	const struct of_device_id *of_id;
+	const struct xwdt_devtype_data *devtype;
+	enum xwdt_ip_type wdttype;
 
 	xdev = devm_kzalloc(dev, sizeof(*xdev), GFP_KERNEL);
 	if (!xdev)
 		return -ENOMEM;
 
 	xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
-	xilinx_wdt_wdd->info = &xilinx_wdt_ident;
-	xilinx_wdt_wdd->ops = &xilinx_wdt_ops;
+
+	of_id = of_match_device(xwdt_of_match, &pdev->dev);
+	if (!of_id)
+		return -EINVAL;
+
+	devtype = of_id->data;
+
+	wdttype = devtype->wdttype;
+
+	xilinx_wdt_wdd->info = devtype->xwdt_info;
+	xilinx_wdt_wdd->ops = devtype->xwdt_ops;
 	xilinx_wdt_wdd->parent = dev;
 
 	xdev->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(xdev->base))
 		return PTR_ERR(xdev->base);
 
-	rc = of_property_read_u32(dev->of_node, "xlnx,wdt-interval",
-				  &xdev->wdt_interval);
-	if (rc)
-		dev_warn(dev, "Parameter \"xlnx,wdt-interval\" not found\n");
+	if (wdttype == XWDT_WDT) {
+		rc = of_property_read_u32(dev->of_node, "xlnx,wdt-interval",
+					  &xdev->wdt_interval);
+		if (rc)
+			dev_warn(dev, "Parameter \"xlnx,wdt-interval\" not found\n");
 
-	rc = of_property_read_u32(dev->of_node, "xlnx,wdt-enable-once",
-				  &enable_once);
-	if (rc)
-		dev_warn(dev,
-			 "Parameter \"xlnx,wdt-enable-once\" not found\n");
+		rc = of_property_read_u32(dev->of_node, "xlnx,wdt-enable-once",
+					  &enable_once);
+		if (rc)
+			dev_warn(dev,
+				 "Parameter \"xlnx,wdt-enable-once\" not found\n");
 
-	watchdog_set_nowayout(xilinx_wdt_wdd, enable_once);
+		watchdog_set_nowayout(xilinx_wdt_wdd, enable_once);
+	} else {
+		rc = of_property_read_u32(dev->of_node, "pretimeout-sec",
+					  &pre_timeout);
+		if (rc)
+			dev_dbg(dev,
+				"Parameter \"pretimeout-sec\" not found\n");
+	}
 
 	xdev->clk = devm_clk_get(dev, NULL);
 	if (IS_ERR(xdev->clk)) {
@@ -222,21 +529,44 @@
 			return rc;
 	}
 
-	/*
-	 * Twice of the 2^wdt_interval / freq  because the first wdt overflow is
-	 * ignored (interrupt), reset is only generated at second wdt overflow
-	 */
-	if (pfreq && xdev->wdt_interval)
-		xilinx_wdt_wdd->timeout = 2 * ((1 << xdev->wdt_interval) /
-					  pfreq);
+	if (wdttype == XWDT_WDT) {
+		/*
+		 * Twice of the 2^wdt_interval / freq  because
+		 * the first wdt overflow is ignored (interrupt),
+		 * reset is only generated at second wdt overflow
+		 */
+		if (pfreq && xdev->wdt_interval)
+			xilinx_wdt_wdd->timeout =
+				2 * ((1 << xdev->wdt_interval) /
+					pfreq);
+	} else {
+		xilinx_wdt_wdd->pretimeout = pre_timeout;
+		xilinx_wdt_wdd->timeout = XWT_WWDT_DEFAULT_TIMEOUT;
+		xilinx_wdt_wdd->min_timeout = XWT_WWDT_MIN_TIMEOUT;
+		xilinx_wdt_wdd->max_timeout = XWT_WWDT_MAX_TIMEOUT;
+		xdev->irq = platform_get_irq_byname(pdev, "wdt");
+		if (xdev->irq > 0) {
+			if (!devm_request_irq(dev, xdev->irq, xilinx_wwdt_isr,
+					      0, dev_name(dev), xdev)) {
+				xilinx_wdt_wdd->info =
+				&xilinx_wwdt_pretimeout_ident;
+			}
+		}
+		rc = watchdog_init_timeout(xilinx_wdt_wdd,
+					   wdt_timeout, &pdev->dev);
+		if (rc)
+			dev_warn(&pdev->dev, "unable to set timeout value\n");
+	}
 
 	spin_lock_init(&xdev->spinlock);
 	watchdog_set_drvdata(xilinx_wdt_wdd, xdev);
 
-	rc = xwdt_selftest(xdev);
-	if (rc == XWT_TIMER_FAILED) {
-		dev_err(dev, "SelfTest routine error\n");
-		return rc;
+	if (wdttype == XWDT_WDT) {
+		rc = xwdt_selftest(xdev);
+		if (rc == XWT_TIMER_FAILED) {
+			dev_err(dev, "SelfTest routine error\n");
+			return rc;
+		}
 	}
 
 	rc = devm_watchdog_register_device(dev, xilinx_wdt_wdd);
@@ -262,9 +592,10 @@
 static int __maybe_unused xwdt_suspend(struct device *dev)
 {
 	struct xwdt_device *xdev = dev_get_drvdata(dev);
+	struct watchdog_device *xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
 
-	if (watchdog_active(&xdev->xilinx_wdt_wdd))
-		xilinx_wdt_stop(&xdev->xilinx_wdt_wdd);
+	if (watchdog_active(xilinx_wdt_wdd))
+		xilinx_wdt_wdd->ops->stop(xilinx_wdt_wdd);
 
 	return 0;
 }
@@ -278,24 +609,17 @@
 static int __maybe_unused xwdt_resume(struct device *dev)
 {
 	struct xwdt_device *xdev = dev_get_drvdata(dev);
+	struct watchdog_device *xilinx_wdt_wdd = &xdev->xilinx_wdt_wdd;
 	int ret = 0;
 
-	if (watchdog_active(&xdev->xilinx_wdt_wdd))
-		ret = xilinx_wdt_start(&xdev->xilinx_wdt_wdd);
+	if (watchdog_active(xilinx_wdt_wdd))
+		ret = xilinx_wdt_wdd->ops->start(xilinx_wdt_wdd);
 
 	return ret;
 }
 
 static SIMPLE_DEV_PM_OPS(xwdt_pm_ops, xwdt_suspend, xwdt_resume);
 
-/* Match table for of_platform binding */
-static const struct of_device_id xwdt_of_match[] = {
-	{ .compatible = "xlnx,xps-timebase-wdt-1.00.a", },
-	{ .compatible = "xlnx,xps-timebase-wdt-1.01.a", },
-	{},
-};
-MODULE_DEVICE_TABLE(of, xwdt_of_match);
-
 static struct platform_driver xwdt_driver = {
 	.probe       = xwdt_probe,
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/pcwd_usb.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/pcwd_usb.c
@@ -325,7 +325,8 @@
 static int usb_pcwd_get_temperature(struct usb_pcwd_private *usb_pcwd,
 							int *temperature)
 {
-	unsigned char msb, lsb;
+	unsigned char msb = 0x00;
+	unsigned char lsb = 0x00;
 
 	usb_pcwd_send_command(usb_pcwd, CMD_READ_TEMP, &msb, &lsb);
 
@@ -341,7 +342,8 @@
 static int usb_pcwd_get_timeleft(struct usb_pcwd_private *usb_pcwd,
 								int *time_left)
 {
-	unsigned char msb, lsb;
+	unsigned char msb = 0x00;
+	unsigned char lsb = 0x00;
 
 	/* Read the time that's left before rebooting */
 	/* Note: if the board is not yet armed then we will read 0xFFFF */
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/rti_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/rti_wdt.c
@@ -52,7 +52,9 @@
 
 #define DWDST			BIT(1)
 
-static int heartbeat = DEFAULT_HEARTBEAT;
+#define MAX_HW_ERROR		250
+
+static int heartbeat;
 
 /*
  * struct to hold data for each WDT device
@@ -70,6 +72,11 @@
 {
 	u32 timer_margin;
 	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+	int ret;
+
+	ret = pm_runtime_resume_and_get(wdd->parent);
+	if (ret)
+		return ret;
 
 	/* set timeout period */
 	timer_margin = (u64)wdd->timeout * wdt->freq;
@@ -85,7 +92,7 @@
 	 * to be 50% or less than that; we obviouly want to configure the open
 	 * window as large as possible so we select the 50% option.
 	 */
-	wdd->min_hw_heartbeat_ms = 500 * wdd->timeout;
+	wdd->min_hw_heartbeat_ms = 520 * wdd->timeout + MAX_HW_ERROR;
 
 	/* Generate NMI when wdt expires */
 	writel_relaxed(RTIWWDRX_NMI, wdt->base + RTIWWDRXCTRL);
@@ -119,31 +126,33 @@
 	 * be petted during the open window; not too early or not too late.
 	 * The HW configuration options only allow for the open window size
 	 * to be 50% or less than that.
+	 * To avoid any glitches, we accommodate 2% + max hardware error
+	 * safety margin.
 	 */
 	switch (wsize) {
 	case RTIWWDSIZE_50P:
-		/* 50% open window => 50% min heartbeat */
-		wdd->min_hw_heartbeat_ms = 500 * heartbeat;
+		/* 50% open window => 52% min heartbeat */
+		wdd->min_hw_heartbeat_ms = 520 * heartbeat + MAX_HW_ERROR;
 		break;
 
 	case RTIWWDSIZE_25P:
-		/* 25% open window => 75% min heartbeat */
-		wdd->min_hw_heartbeat_ms = 750 * heartbeat;
+		/* 25% open window => 77% min heartbeat */
+		wdd->min_hw_heartbeat_ms = 770 * heartbeat + MAX_HW_ERROR;
 		break;
 
 	case RTIWWDSIZE_12P5:
-		/* 12.5% open window => 87.5% min heartbeat */
-		wdd->min_hw_heartbeat_ms = 875 * heartbeat;
+		/* 12.5% open window => 89.5% min heartbeat */
+		wdd->min_hw_heartbeat_ms = 895 * heartbeat + MAX_HW_ERROR;
 		break;
 
 	case RTIWWDSIZE_6P25:
-		/* 6.5% open window => 93.5% min heartbeat */
-		wdd->min_hw_heartbeat_ms = 935 * heartbeat;
+		/* 6.5% open window => 95.5% min heartbeat */
+		wdd->min_hw_heartbeat_ms = 955 * heartbeat + MAX_HW_ERROR;
 		break;
 
 	case RTIWWDSIZE_3P125:
-		/* 3.125% open window => 96.9% min heartbeat */
-		wdd->min_hw_heartbeat_ms = 969 * heartbeat;
+		/* 3.125% open window => 98.9% min heartbeat */
+		wdd->min_hw_heartbeat_ms = 989 * heartbeat + MAX_HW_ERROR;
 		break;
 
 	default:
@@ -217,18 +226,11 @@
 		return -EINVAL;
 	}
 
-	/*
-	 * If watchdog is running at 32k clock, it is not accurate.
-	 * Adjust frequency down in this case so that we don't pet
-	 * the watchdog too often.
-	 */
-	if (wdt->freq < 32768)
-		wdt->freq = wdt->freq * 9 / 10;
-
 	pm_runtime_enable(dev);
 	ret = pm_runtime_get_sync(dev);
-	if (ret) {
+	if (ret < 0) {
 		pm_runtime_put_noidle(dev);
+		pm_runtime_disable(&pdev->dev);
 		return dev_err_probe(dev, ret, "runtime pm failed\n");
 	}
 
@@ -240,6 +242,7 @@
 	wdd->min_timeout = 1;
 	wdd->max_hw_heartbeat_ms = (WDT_PRELOAD_MAX << WDT_PRELOAD_SHIFT) /
 		wdt->freq * 1000;
+	wdd->timeout = DEFAULT_HEARTBEAT;
 	wdd->parent = dev;
 
 	watchdog_set_drvdata(wdd, wdt);
@@ -295,6 +298,9 @@
 	if (last_ping)
 		watchdog_set_last_hw_keepalive(wdd, last_ping);
 
+	if (!watchdog_hw_running(wdd))
+		pm_runtime_put_sync(&pdev->dev);
+
 	return 0;
 
 err_iomap:
@@ -309,7 +315,10 @@
 	struct rti_wdt_device *wdt = platform_get_drvdata(pdev);
 
 	watchdog_unregister_device(&wdt->wdd);
-	pm_runtime_put(&pdev->dev);
+
+	if (!pm_runtime_suspended(&pdev->dev))
+		pm_runtime_put(&pdev->dev);
+
 	pm_runtime_disable(&pdev->dev);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/sbsa_gwdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/sbsa_gwdt.c
@@ -150,16 +150,17 @@
 	struct sbsa_gwdt *gwdt = watchdog_get_drvdata(wdd);
 
 	wdd->timeout = timeout;
+	timeout = clamp_t(unsigned int, timeout, 1, wdd->max_hw_heartbeat_ms / 1000);
 
 	if (action)
-		sbsa_gwdt_reg_write(gwdt->clk * timeout, gwdt);
+		sbsa_gwdt_reg_write((u64)gwdt->clk * timeout, gwdt);
 	else
 		/*
 		 * In the single stage mode, The first signal (WS0) is ignored,
 		 * the timeout is (WOR * 2), so the WOR should be configured
 		 * to half value of timeout.
 		 */
-		sbsa_gwdt_reg_write(gwdt->clk / 2 * timeout, gwdt);
+		sbsa_gwdt_reg_write(((u64)gwdt->clk / 2) * timeout, gwdt);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/sp5100_tco.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/sp5100_tco.c
@@ -48,7 +48,7 @@
 /* internal variables */
 
 enum tco_reg_layout {
-	sp5100, sb800, efch
+	sp5100, sb800, efch, efch_mmio
 };
 
 struct sp5100_tco {
@@ -86,6 +86,10 @@
 	    dev->revision < 0x40) {
 		return sp5100;
 	} else if (dev->vendor == PCI_VENDOR_ID_AMD &&
+	    sp5100_tco_pci->device == PCI_DEVICE_ID_AMD_KERNCZ_SMBUS &&
+	    sp5100_tco_pci->revision >= AMD_ZEN_SMBUS_PCI_REV) {
+		return efch_mmio;
+	} else if ((dev->vendor == PCI_VENDOR_ID_AMD || dev->vendor == PCI_VENDOR_ID_HYGON) &&
 	    ((dev->device == PCI_DEVICE_ID_AMD_HUDSON2_SMBUS &&
 	     dev->revision >= 0x41) ||
 	    (dev->device == PCI_DEVICE_ID_AMD_KERNCZ_SMBUS &&
@@ -104,6 +108,10 @@
 	val |= SP5100_WDT_START_STOP_BIT;
 	writel(val, SP5100_WDT_CONTROL(tco->tcobase));
 
+	/* This must be a distinct write. */
+	val |= SP5100_WDT_TRIGGER_BIT;
+	writel(val, SP5100_WDT_CONTROL(tco->tcobase));
+
 	return 0;
 }
 
@@ -201,6 +209,8 @@
 					  ~EFCH_PM_WATCHDOG_DISABLE,
 					  EFCH_PM_DECODEEN_SECOND_RES);
 		break;
+	default:
+		break;
 	}
 }
 
@@ -215,14 +225,196 @@
 	return val;
 }
 
+static u32 sp5100_tco_request_region(struct device *dev,
+				     u32 mmio_addr,
+				     const char *dev_name)
+{
+	if (!devm_request_mem_region(dev, mmio_addr, SP5100_WDT_MEM_MAP_SIZE,
+				     dev_name)) {
+		dev_dbg(dev, "MMIO address 0x%08x already in use\n", mmio_addr);
+		return 0;
+	}
+
+	return mmio_addr;
+}
+
+static u32 sp5100_tco_prepare_base(struct sp5100_tco *tco,
+				   u32 mmio_addr,
+				   u32 alt_mmio_addr,
+				   const char *dev_name)
+{
+	struct device *dev = tco->wdd.parent;
+
+	dev_dbg(dev, "Got 0x%08x from SBResource_MMIO register\n", mmio_addr);
+
+	if (!mmio_addr && !alt_mmio_addr)
+		return -ENODEV;
+
+	/* Check for MMIO address and alternate MMIO address conflicts */
+	if (mmio_addr)
+		mmio_addr = sp5100_tco_request_region(dev, mmio_addr, dev_name);
+
+	if (!mmio_addr && alt_mmio_addr)
+		mmio_addr = sp5100_tco_request_region(dev, alt_mmio_addr, dev_name);
+
+	if (!mmio_addr) {
+		dev_err(dev, "Failed to reserve MMIO or alternate MMIO region\n");
+		return -EBUSY;
+	}
+
+	tco->tcobase = devm_ioremap(dev, mmio_addr, SP5100_WDT_MEM_MAP_SIZE);
+	if (!tco->tcobase) {
+		dev_err(dev, "MMIO address 0x%08x failed mapping\n", mmio_addr);
+		devm_release_mem_region(dev, mmio_addr, SP5100_WDT_MEM_MAP_SIZE);
+		return -ENOMEM;
+	}
+
+	dev_info(dev, "Using 0x%08x for watchdog MMIO address\n", mmio_addr);
+
+	return 0;
+}
+
+static int sp5100_tco_timer_init(struct sp5100_tco *tco)
+{
+	struct watchdog_device *wdd = &tco->wdd;
+	struct device *dev = wdd->parent;
+	u32 val;
+
+	val = readl(SP5100_WDT_CONTROL(tco->tcobase));
+	if (val & SP5100_WDT_DISABLED) {
+		dev_err(dev, "Watchdog hardware is disabled\n");
+		return -ENODEV;
+	}
+
+	/*
+	 * Save WatchDogFired status, because WatchDogFired flag is
+	 * cleared here.
+	 */
+	if (val & SP5100_WDT_FIRED)
+		wdd->bootstatus = WDIOF_CARDRESET;
+
+	/* Set watchdog action to reset the system */
+	val &= ~SP5100_WDT_ACTION_RESET;
+	writel(val, SP5100_WDT_CONTROL(tco->tcobase));
+
+	/* Set a reasonable heartbeat before we stop the timer */
+	tco_timer_set_timeout(wdd, wdd->timeout);
+
+	/*
+	 * Stop the TCO before we change anything so we don't race with
+	 * a zeroed timer.
+	 */
+	tco_timer_stop(wdd);
+
+	return 0;
+}
+
+static u8 efch_read_pm_reg8(void __iomem *addr, u8 index)
+{
+	return readb(addr + index);
+}
+
+static void efch_update_pm_reg8(void __iomem *addr, u8 index, u8 reset, u8 set)
+{
+	u8 val;
+
+	val = readb(addr + index);
+	val &= reset;
+	val |= set;
+	writeb(val, addr + index);
+}
+
+static void tco_timer_enable_mmio(void __iomem *addr)
+{
+	efch_update_pm_reg8(addr, EFCH_PM_DECODEEN3,
+			    ~EFCH_PM_WATCHDOG_DISABLE,
+			    EFCH_PM_DECODEEN_SECOND_RES);
+}
+
+static int sp5100_tco_setupdevice_mmio(struct device *dev,
+				       struct watchdog_device *wdd)
+{
+	struct sp5100_tco *tco = watchdog_get_drvdata(wdd);
+	const char *dev_name = SB800_DEVNAME;
+	u32 mmio_addr = 0, alt_mmio_addr = 0;
+	struct resource *res;
+	void __iomem *addr;
+	int ret;
+	u32 val;
+
+	res = request_mem_region_muxed(EFCH_PM_ACPI_MMIO_PM_ADDR,
+				       EFCH_PM_ACPI_MMIO_PM_SIZE,
+				       "sp5100_tco");
+
+	if (!res) {
+		dev_err(dev,
+			"Memory region 0x%08x already in use\n",
+			EFCH_PM_ACPI_MMIO_PM_ADDR);
+		return -EBUSY;
+	}
+
+	addr = ioremap(EFCH_PM_ACPI_MMIO_PM_ADDR, EFCH_PM_ACPI_MMIO_PM_SIZE);
+	if (!addr) {
+		dev_err(dev, "Address mapping failed\n");
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	/*
+	 * EFCH_PM_DECODEEN_WDT_TMREN is dual purpose. This bitfield
+	 * enables sp5100_tco register MMIO space decoding. The bitfield
+	 * also starts the timer operation. Enable if not already enabled.
+	 */
+	val = efch_read_pm_reg8(addr, EFCH_PM_DECODEEN);
+	if (!(val & EFCH_PM_DECODEEN_WDT_TMREN)) {
+		efch_update_pm_reg8(addr, EFCH_PM_DECODEEN, 0xff,
+				    EFCH_PM_DECODEEN_WDT_TMREN);
+	}
+
+	/* Error if the timer could not be enabled */
+	val = efch_read_pm_reg8(addr, EFCH_PM_DECODEEN);
+	if (!(val & EFCH_PM_DECODEEN_WDT_TMREN)) {
+		dev_err(dev, "Failed to enable the timer\n");
+		ret = -EFAULT;
+		goto out;
+	}
+
+	mmio_addr = EFCH_PM_WDT_ADDR;
+
+	/* Determine alternate MMIO base address */
+	val = efch_read_pm_reg8(addr, EFCH_PM_ISACONTROL);
+	if (val & EFCH_PM_ISACONTROL_MMIOEN)
+		alt_mmio_addr = EFCH_PM_ACPI_MMIO_ADDR +
+			EFCH_PM_ACPI_MMIO_WDT_OFFSET;
+
+	ret = sp5100_tco_prepare_base(tco, mmio_addr, alt_mmio_addr, dev_name);
+	if (!ret) {
+		tco_timer_enable_mmio(addr);
+		ret = sp5100_tco_timer_init(tco);
+	}
+
+out:
+	if (addr)
+		iounmap(addr);
+
+	release_resource(res);
+	kfree(res);
+
+	return ret;
+}
+
 static int sp5100_tco_setupdevice(struct device *dev,
 				  struct watchdog_device *wdd)
 {
 	struct sp5100_tco *tco = watchdog_get_drvdata(wdd);
 	const char *dev_name;
 	u32 mmio_addr = 0, val;
+	u32 alt_mmio_addr = 0;
 	int ret;
 
+	if (tco->tco_reg_layout == efch_mmio)
+		return sp5100_tco_setupdevice_mmio(dev, wdd);
+
 	/* Request the IO ports used by this driver */
 	if (!request_muxed_region(SP5100_IO_PM_INDEX_REG,
 				  SP5100_PM_IOPORTS_SIZE, "sp5100_tco")) {
@@ -239,138 +431,55 @@
 		dev_name = SP5100_DEVNAME;
 		mmio_addr = sp5100_tco_read_pm_reg32(SP5100_PM_WATCHDOG_BASE) &
 								0xfffffff8;
+
+		/*
+		 * Secondly, find the watchdog timer MMIO address
+		 * from SBResource_MMIO register.
+		 */
+
+		/* Read SBResource_MMIO from PCI config(PCI_Reg: 9Ch) */
+		pci_read_config_dword(sp5100_tco_pci,
+				      SP5100_SB_RESOURCE_MMIO_BASE,
+				      &val);
+
+		/* Verify MMIO is enabled and using bar0 */
+		if ((val & SB800_ACPI_MMIO_MASK) == SB800_ACPI_MMIO_DECODE_EN)
+			alt_mmio_addr = (val & ~0xfff) + SB800_PM_WDT_MMIO_OFFSET;
 		break;
 	case sb800:
 		dev_name = SB800_DEVNAME;
 		mmio_addr = sp5100_tco_read_pm_reg32(SB800_PM_WATCHDOG_BASE) &
 								0xfffffff8;
+
+		/* Read SBResource_MMIO from AcpiMmioEn(PM_Reg: 24h) */
+		val = sp5100_tco_read_pm_reg32(SB800_PM_ACPI_MMIO_EN);
+
+		/* Verify MMIO is enabled and using bar0 */
+		if ((val & SB800_ACPI_MMIO_MASK) == SB800_ACPI_MMIO_DECODE_EN)
+			alt_mmio_addr = (val & ~0xfff) + SB800_PM_WDT_MMIO_OFFSET;
 		break;
 	case efch:
 		dev_name = SB800_DEVNAME;
-		/*
-		 * On Family 17h devices, the EFCH_PM_DECODEEN_WDT_TMREN bit of
-		 * EFCH_PM_DECODEEN not only enables the EFCH_PM_WDT_ADDR memory
-		 * region, it also enables the watchdog itself.
-		 */
-		if (boot_cpu_data.x86 == 0x17) {
-			val = sp5100_tco_read_pm_reg8(EFCH_PM_DECODEEN);
-			if (!(val & EFCH_PM_DECODEEN_WDT_TMREN)) {
-				sp5100_tco_update_pm_reg8(EFCH_PM_DECODEEN, 0xff,
-							  EFCH_PM_DECODEEN_WDT_TMREN);
-			}
-		}
 		val = sp5100_tco_read_pm_reg8(EFCH_PM_DECODEEN);
 		if (val & EFCH_PM_DECODEEN_WDT_TMREN)
 			mmio_addr = EFCH_PM_WDT_ADDR;
+
+		val = sp5100_tco_read_pm_reg8(EFCH_PM_ISACONTROL);
+		if (val & EFCH_PM_ISACONTROL_MMIOEN)
+			alt_mmio_addr = EFCH_PM_ACPI_MMIO_ADDR +
+				EFCH_PM_ACPI_MMIO_WDT_OFFSET;
 		break;
 	default:
 		return -ENODEV;
 	}
 
-	/* Check MMIO address conflict */
-	if (!mmio_addr ||
-	    !devm_request_mem_region(dev, mmio_addr, SP5100_WDT_MEM_MAP_SIZE,
-				     dev_name)) {
-		if (mmio_addr)
-			dev_dbg(dev, "MMIO address 0x%08x already in use\n",
-				mmio_addr);
-		switch (tco->tco_reg_layout) {
-		case sp5100:
-			/*
-			 * Secondly, Find the watchdog timer MMIO address
-			 * from SBResource_MMIO register.
-			 */
-			/* Read SBResource_MMIO from PCI config(PCI_Reg: 9Ch) */
-			pci_read_config_dword(sp5100_tco_pci,
-					      SP5100_SB_RESOURCE_MMIO_BASE,
-					      &mmio_addr);
-			if ((mmio_addr & (SB800_ACPI_MMIO_DECODE_EN |
-					  SB800_ACPI_MMIO_SEL)) !=
-						  SB800_ACPI_MMIO_DECODE_EN) {
-				ret = -ENODEV;
-				goto unreg_region;
-			}
-			mmio_addr &= ~0xFFF;
-			mmio_addr += SB800_PM_WDT_MMIO_OFFSET;
-			break;
-		case sb800:
-			/* Read SBResource_MMIO from AcpiMmioEn(PM_Reg: 24h) */
-			mmio_addr =
-				sp5100_tco_read_pm_reg32(SB800_PM_ACPI_MMIO_EN);
-			if ((mmio_addr & (SB800_ACPI_MMIO_DECODE_EN |
-					  SB800_ACPI_MMIO_SEL)) !=
-						  SB800_ACPI_MMIO_DECODE_EN) {
-				ret = -ENODEV;
-				goto unreg_region;
-			}
-			mmio_addr &= ~0xFFF;
-			mmio_addr += SB800_PM_WDT_MMIO_OFFSET;
-			break;
-		case efch:
-			val = sp5100_tco_read_pm_reg8(EFCH_PM_ISACONTROL);
-			if (!(val & EFCH_PM_ISACONTROL_MMIOEN)) {
-				ret = -ENODEV;
-				goto unreg_region;
-			}
-			mmio_addr = EFCH_PM_ACPI_MMIO_ADDR +
-				    EFCH_PM_ACPI_MMIO_WDT_OFFSET;
-			break;
-		}
-		dev_dbg(dev, "Got 0x%08x from SBResource_MMIO register\n",
-			mmio_addr);
-		if (!devm_request_mem_region(dev, mmio_addr,
-					     SP5100_WDT_MEM_MAP_SIZE,
-					     dev_name)) {
-			dev_dbg(dev, "MMIO address 0x%08x already in use\n",
-				mmio_addr);
-			ret = -EBUSY;
-			goto unreg_region;
-		}
-	}
-
-	tco->tcobase = devm_ioremap(dev, mmio_addr, SP5100_WDT_MEM_MAP_SIZE);
-	if (!tco->tcobase) {
-		dev_err(dev, "failed to get tcobase address\n");
-		ret = -ENOMEM;
-		goto unreg_region;
+	ret = sp5100_tco_prepare_base(tco, mmio_addr, alt_mmio_addr, dev_name);
+	if (!ret) {
+		/* Setup the watchdog timer */
+		tco_timer_enable(tco);
+		ret = sp5100_tco_timer_init(tco);
 	}
 
-	dev_info(dev, "Using 0x%08x for watchdog MMIO address\n", mmio_addr);
-
-	/* Setup the watchdog timer */
-	tco_timer_enable(tco);
-
-	val = readl(SP5100_WDT_CONTROL(tco->tcobase));
-	if (val & SP5100_WDT_DISABLED) {
-		dev_err(dev, "Watchdog hardware is disabled\n");
-		ret = -ENODEV;
-		goto unreg_region;
-	}
-
-	/*
-	 * Save WatchDogFired status, because WatchDogFired flag is
-	 * cleared here.
-	 */
-	if (val & SP5100_WDT_FIRED)
-		wdd->bootstatus = WDIOF_CARDRESET;
-	/* Set watchdog action to reset the system */
-	val &= ~SP5100_WDT_ACTION_RESET;
-	writel(val, SP5100_WDT_CONTROL(tco->tcobase));
-
-	/* Set a reasonable heartbeat before we stop the timer */
-	tco_timer_set_timeout(wdd, wdd->timeout);
-
-	/*
-	 * Stop the TCO before we change anything so we don't race with
-	 * a zeroed timer.
-	 */
-	tco_timer_stop(wdd);
-
-	release_region(SP5100_IO_PM_INDEX_REG, SP5100_PM_IOPORTS_SIZE);
-
-	return 0;
-
-unreg_region:
 	release_region(SP5100_IO_PM_INDEX_REG, SP5100_PM_IOPORTS_SIZE);
 	return ret;
 }
@@ -452,6 +561,8 @@
 	  PCI_ANY_ID, },
 	{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_KERNCZ_SMBUS, PCI_ANY_ID,
 	  PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_HYGON, PCI_DEVICE_ID_AMD_KERNCZ_SMBUS, PCI_ANY_ID,
+	  PCI_ANY_ID, },
 	{ 0, },			/* End of list */
 };
 MODULE_DEVICE_TABLE(pci, sp5100_tco_pci_tbl);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/sp5100_tco.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/sp5100_tco.h
@@ -58,6 +58,7 @@
 #define SB800_PM_WATCHDOG_SECOND_RES	GENMASK(1, 0)
 #define SB800_ACPI_MMIO_DECODE_EN	BIT(0)
 #define SB800_ACPI_MMIO_SEL		BIT(1)
+#define SB800_ACPI_MMIO_MASK		GENMASK(1, 0)
 
 #define SB800_PM_WDT_MMIO_OFFSET	0xB00
 
@@ -82,4 +83,10 @@
 #define EFCH_PM_ISACONTROL_MMIOEN	BIT(1)
 
 #define EFCH_PM_ACPI_MMIO_ADDR		0xfed80000
+#define EFCH_PM_ACPI_MMIO_PM_OFFSET	0x00000300
 #define EFCH_PM_ACPI_MMIO_WDT_OFFSET	0x00000b00
+
+#define EFCH_PM_ACPI_MMIO_PM_ADDR	(EFCH_PM_ACPI_MMIO_ADDR +	\
+					 EFCH_PM_ACPI_MMIO_PM_OFFSET)
+#define EFCH_PM_ACPI_MMIO_PM_SIZE	8
+#define AMD_ZEN_SMBUS_PCI_REV		0x51
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/stm32_iwdg.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/stm32_iwdg.c
@@ -21,6 +21,8 @@
 #include <linux/platform_device.h>
 #include <linux/watchdog.h>
 
+#define DEFAULT_TIMEOUT 10
+
 /* IWDG registers */
 #define IWDG_KR		0x00 /* Key register */
 #define IWDG_PR		0x04 /* Prescaler Register */
@@ -251,6 +253,7 @@
 	wdd->parent = dev;
 	wdd->info = &stm32_iwdg_info;
 	wdd->ops = &stm32_iwdg_ops;
+	wdd->timeout = DEFAULT_TIMEOUT;
 	wdd->min_timeout = DIV_ROUND_UP((RLR_MIN + 1) * PR_MIN, wdt->rate);
 	wdd->max_hw_heartbeat_ms = ((RLR_MAX + 1) * wdt->data->max_prescaler *
 				    1000) / wdt->rate;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/ts4800_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/ts4800_wdt.c
@@ -125,13 +125,16 @@
 	ret = of_property_read_u32_index(np, "syscon", 1, &reg);
 	if (ret < 0) {
 		dev_err(dev, "no offset in syscon\n");
+		of_node_put(syscon_np);
 		return ret;
 	}
 
 	/* allocate memory for watchdog struct */
 	wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
-	if (!wdt)
+	if (!wdt) {
+		of_node_put(syscon_np);
 		return -ENOMEM;
+	}
 
 	/* set regmap and offset to know where to write */
 	wdt->feed_offset = reg;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/watchdog_dev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/watchdog_dev.c
@@ -1035,6 +1035,7 @@
 
 	/* Fill in the data structures */
 	cdev_init(&wd_data->cdev, &watchdog_fops);
+	wd_data->cdev.owner = wdd->ops->owner;
 
 	/* Add the device */
 	err = cdev_device_add(&wd_data->cdev, &wd_data->dev);
@@ -1044,13 +1045,11 @@
 		if (wdd->id == 0) {
 			misc_deregister(&watchdog_miscdev);
 			old_wd_data = NULL;
-			put_device(&wd_data->dev);
 		}
+		put_device(&wd_data->dev);
 		return err;
 	}
 
-	wd_data->cdev.owner = wdd->ops->owner;
-
 	/* Record time of most recent heartbeat as 'just before now'. */
 	wd_data->last_hw_keepalive = ktime_sub(ktime_get(), 1);
 	watchdog_set_open_deadline(wd_data);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/wdat_wdt.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/wdat_wdt.c
@@ -462,6 +462,7 @@
 		return ret;
 
 	watchdog_set_nowayout(&wdat->wdd, nowayout);
+	watchdog_stop_on_reboot(&wdat->wdd);
 	return devm_watchdog_register_device(dev, &wdat->wdd);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/watchdog/wdt_aaeon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/watchdog/wdt_aaeon.c
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * AAEON WDT driver
+ *
+ * Author: Edward Lin <edward1_lin@aaeon.com.tw>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/acpi.h>
+#include <linux/fs.h>
+#include <linux/err.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/notifier.h>
+#include <linux/platform_data/x86/asus-wmi.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <linux/uaccess.h>
+#include <linux/watchdog.h>
+
+#define AAEON_WMI_MGMT_GUID      "97845ED0-4E6D-11DE-8A39-0800200C9A66"
+#define WMI_WDT_GETMAX_METHOD_ID	0x00020000
+#define WMI_WDT_GETVALUE_METHOD_ID	0x00020001
+#define WMI_WDT_SETANDSTOP_METHOD_ID	0x00020002
+
+#define WMI_WDT_SUPPORTED_DEVICE_ID                                            \
+	0x12 /* Dev_Id for WDT_WMI supported or not */
+#define WMI_WDT_GETMAX_DEVICE_ID  0x10  /* Dev_Id for WDT_WMI get Max timeout */
+#define WMI_WDT_STOP_DEVICE_ID    0x00  /* Dev_Id for WDT_WMI stop watchdog*/
+
+/* Default values */
+#define WATCHDOG_TIMEOUT  60000  /* 1 minute default timeout */
+#define WATCHDOG_MAX_TIMEOUT  (60000 * 255) /* WD_TIME is a byte long */
+#define WATCHDOG_PULSE_WIDTH  5000 /* default pulse width for watchdog signal */
+
+static const int max_timeout = WATCHDOG_MAX_TIMEOUT;
+static int timeout = WATCHDOG_TIMEOUT;    /* default timeout in seconds */
+module_param(timeout, int, 0);
+MODULE_PARM_DESC(timeout, "Initial watchdog timeout in mini-seconds");
+
+static bool nowayout = WATCHDOG_NOWAYOUT;
+module_param(nowayout, bool, 0444);
+MODULE_PARM_DESC(nowayout, " Disable watchdog shutdown on close");
+
+/* Wdog internal data information */
+struct watchdog_data {
+	unsigned long       opened;       /* driver open state */
+	struct mutex        lock;         /* concurrency control */
+	char                expect_close; /* controlled close */
+	struct watchdog_info ident;       /* wdog information*/
+	unsigned short      timeout;      /* current wdog timeout */
+	u8                  timer_val;    /* content for the WD_TIME register */
+	char                minutes_mode;
+	u8                  pulse_val;    /* pulse width flag */
+	char                pulse_mode;   /* enable pulse output mode? */
+	char                caused_reboot;/* last reboot was by the watchdog */
+};
+
+static long aaeon_watchdog_ioctl(struct file *file, unsigned int cmd,
+			  unsigned long arg);
+static int aaeon_watchdog_notify_sys(struct notifier_block *this,
+			       unsigned long code, void *unused);
+
+static struct watchdog_data watchdog = {
+	.lock = __MUTEX_INITIALIZER(watchdog.lock),
+};
+
+/* /dev/watchdog api available options */
+static const struct file_operations watchdog_fops = {
+	.owner              = THIS_MODULE,
+	.unlocked_ioctl     = aaeon_watchdog_ioctl,
+};
+
+static struct miscdevice watchdog_miscdev = {
+	.minor      = WATCHDOG_MINOR,
+	.name       = "watchdog",
+	.fops       = &watchdog_fops,
+};
+
+static struct notifier_block watchdog_notifier = {
+	.notifier_call = aaeon_watchdog_notify_sys,
+};
+
+/* Internal Configuration functions */
+static int aaeon_watchdog_set_timeout(int timeout)
+{
+	int err = 0;
+	u32 retval, dev_id = timeout;
+
+	if (timeout <= 0 || timeout >  max_timeout) {
+		pr_debug("watchdog timeout out of range\n");
+		return -EINVAL;
+	}
+
+	mutex_lock(&watchdog.lock);
+	err = asus_wmi_evaluate_method(WMI_WDT_SETANDSTOP_METHOD_ID,
+				       dev_id, 0, &retval);
+	mutex_unlock(&watchdog.lock);
+
+	return err;
+}
+
+static int aaeon_watchdog_get_timeout(void)
+{
+	int err = 0;
+	u32 retval;
+
+	if (timeout <= 0 || timeout >  max_timeout) {
+		pr_debug("watchdog timeout out of range\n");
+		return -EINVAL;
+	}
+	mutex_lock(&watchdog.lock);
+	err = asus_wmi_evaluate_method(WMI_WDT_GETVALUE_METHOD_ID,
+				       0, 0, &retval);
+	mutex_unlock(&watchdog.lock);
+
+	return err ? err : retval;
+}
+
+static int aaeon_watchdog_stop(void)
+{
+	int err = 0;
+
+	mutex_lock(&watchdog.lock);
+	err = asus_wmi_evaluate_method(WMI_WDT_SETANDSTOP_METHOD_ID,
+				       0, 0, NULL);
+	mutex_unlock(&watchdog.lock);
+
+	return err;
+}
+
+static int aaeon_watchdog_get_maxsupport(void)
+{
+	int err;
+	u32 retval;
+
+	mutex_lock(&watchdog.lock);
+	err = asus_wmi_evaluate_method(WMI_WDT_GETMAX_METHOD_ID,
+				       WMI_WDT_GETMAX_DEVICE_ID,
+				       0, &retval);
+	mutex_unlock(&watchdog.lock);
+
+	return err ? err : retval;
+
+}
+
+static long aaeon_watchdog_ioctl(struct file *file, unsigned int cmd,
+			  unsigned long arg)
+{
+	int new_timeout;
+
+	union {
+		struct watchdog_info __user *ident;
+		int __user *i;
+	} uarg;
+
+	uarg.i = (int __user *) arg;
+	switch (cmd) {
+	case WDIOC_SETTIMEOUT:
+		if (get_user(new_timeout, uarg.i))
+			return -EFAULT;
+		if (aaeon_watchdog_set_timeout(new_timeout))
+			return -EINVAL;
+		return 0;
+	case WDIOC_GETTIMEOUT:
+		return aaeon_watchdog_get_timeout();
+	case WDIOS_DISABLECARD:
+		return aaeon_watchdog_stop();
+	case WDIOC_GETSUPPORT:
+		return aaeon_watchdog_get_maxsupport();
+	default:
+		return -ENOTTY;
+	}
+}
+
+static int aaeon_watchdog_notify_sys(struct notifier_block *this,
+			       unsigned long code, void *unused)
+{
+	if (code == SYS_DOWN || code == SYS_HALT)
+		aaeon_watchdog_stop();
+	return NOTIFY_DONE;
+}
+
+static int aaeon_wdt_probe(struct platform_device *pdev)
+{
+	int err = 0;
+	int retval = 0;
+
+	pr_debug("aaeon watchdog device probe!\n");
+	if (!wmi_has_guid(AAEON_WMI_MGMT_GUID)) {
+		pr_debug("AAEON Management GUID not found\n");
+		return -ENODEV;
+	}
+	err = asus_wmi_evaluate_method(WMI_WDT_GETMAX_METHOD_ID,
+				       WMI_WDT_SUPPORTED_DEVICE_ID, 0, &retval);
+	if (err)
+		goto exit;
+
+	/*
+	 * This driver imitates the old type SIO watchdog driver to
+	 * provide the basic control for watchdog functions and only
+	 * access by customized userspace tool
+	 */
+	err = misc_register(&watchdog_miscdev);
+	if (err) {
+		pr_debug(" cannot register miscdev on minor=%d\n",
+			 watchdog_miscdev.minor);
+		goto exit;
+	}
+
+	err = register_reboot_notifier(&watchdog_notifier);
+	if (err)
+		goto exit_miscdev;
+
+	if (nowayout)
+		__module_get(THIS_MODULE);
+
+	return 0;
+
+exit_miscdev:
+	misc_deregister(&watchdog_miscdev);
+exit:
+	return err;
+}
+
+static struct platform_driver aaeon_wdt_driver = {
+	.driver = {
+		.name = "wdt-aaeon",
+	},
+};
+
+module_platform_driver_probe(aaeon_wdt_driver, aaeon_wdt_probe);
+
+MODULE_ALIAS("platform:wdt-aaeon");
+MODULE_DESCRIPTION("AAEON WDT Driver");
+MODULE_AUTHOR("Edward Lin <edward1_lin@aaeon.com.tw>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/Kconfig
@@ -205,7 +205,7 @@
 	  If in doubt, say m.
 
 config XEN_PVCALLS_FRONTEND
-	tristate "XEN PV Calls frontend driver"
+	bool "XEN PV Calls frontend driver"
 	depends on INET && XEN
 	select XEN_XENBUS_FRONTEND
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/Makefile
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/Makefile
@@ -32,6 +32,7 @@
 obj-$(CONFIG_XEN_AUTO_XLATE)		+= xlate_mmu.o
 obj-$(CONFIG_XEN_PVCALLS_BACKEND)	+= pvcalls-back.o
 obj-$(CONFIG_XEN_PVCALLS_FRONTEND)	+= pvcalls-front.o
+obj-$(CONFIG_XEN_PVCALLS_FRONTEND)	+= pvcalls.o
 xen-evtchn-y				:= evtchn.o
 xen-gntdev-y				:= gntdev.o
 xen-gntdev-$(CONFIG_XEN_GNTDEV_DMABUF)	+= gntdev-dmabuf.o
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/balloon.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/balloon.c
@@ -58,6 +58,7 @@
 #include <linux/percpu-defs.h>
 #include <linux/slab.h>
 #include <linux/sysctl.h>
+#include <linux/moduleparam.h>
 
 #include <asm/page.h>
 #include <asm/tlb.h>
@@ -73,6 +74,12 @@
 #include <xen/page.h>
 #include <xen/mem-reservation.h>
 
+#undef MODULE_PARAM_PREFIX
+#define MODULE_PARAM_PREFIX "xen."
+
+static uint __read_mostly balloon_boot_timeout = 180;
+module_param(balloon_boot_timeout, uint, 0444);
+
 static int xen_hotplug_unpopulated;
 
 #ifdef CONFIG_XEN_BALLOON_MEMORY_HOTPLUG
@@ -125,12 +132,12 @@
  * BP_ECANCELED: error, balloon operation canceled.
  */
 
-enum bp_state {
+static enum bp_state {
 	BP_DONE,
 	BP_WAIT,
 	BP_EAGAIN,
 	BP_ECANCELED
-};
+} balloon_state = BP_DONE;
 
 /* Main waiting point for xen-balloon thread. */
 static DECLARE_WAIT_QUEUE_HEAD(balloon_thread_wq);
@@ -199,18 +206,15 @@
 	return list_entry(next, struct page, lru);
 }
 
-static enum bp_state update_schedule(enum bp_state state)
+static void update_schedule(void)
 {
-	if (state == BP_WAIT)
-		return BP_WAIT;
-
-	if (state == BP_ECANCELED)
-		return BP_ECANCELED;
+	if (balloon_state == BP_WAIT || balloon_state == BP_ECANCELED)
+		return;
 
-	if (state == BP_DONE) {
+	if (balloon_state == BP_DONE) {
 		balloon_stats.schedule_delay = 1;
 		balloon_stats.retry_count = 1;
-		return BP_DONE;
+		return;
 	}
 
 	++balloon_stats.retry_count;
@@ -219,7 +223,8 @@
 			balloon_stats.retry_count > balloon_stats.max_retry_count) {
 		balloon_stats.schedule_delay = 1;
 		balloon_stats.retry_count = 1;
-		return BP_ECANCELED;
+		balloon_state = BP_ECANCELED;
+		return;
 	}
 
 	balloon_stats.schedule_delay <<= 1;
@@ -227,7 +232,7 @@
 	if (balloon_stats.schedule_delay > balloon_stats.max_schedule_delay)
 		balloon_stats.schedule_delay = balloon_stats.max_schedule_delay;
 
-	return BP_EAGAIN;
+	balloon_state = BP_EAGAIN;
 }
 
 #ifdef CONFIG_XEN_BALLOON_MEMORY_HOTPLUG
@@ -494,9 +499,9 @@
  * Stop waiting if either state is BP_DONE and ballooning action is
  * needed, or if the credit has changed while state is not BP_DONE.
  */
-static bool balloon_thread_cond(enum bp_state state, long credit)
+static bool balloon_thread_cond(long credit)
 {
-	if (state == BP_DONE)
+	if (balloon_state == BP_DONE)
 		credit = 0;
 
 	return current_credit() != credit || kthread_should_stop();
@@ -510,13 +515,12 @@
  */
 static int balloon_thread(void *unused)
 {
-	enum bp_state state = BP_DONE;
 	long credit;
 	unsigned long timeout;
 
 	set_freezable();
 	for (;;) {
-		switch (state) {
+		switch (balloon_state) {
 		case BP_DONE:
 		case BP_ECANCELED:
 			timeout = 3600 * HZ;
@@ -532,7 +536,7 @@
 		credit = current_credit();
 
 		wait_event_freezable_timeout(balloon_thread_wq,
-			balloon_thread_cond(state, credit), timeout);
+			balloon_thread_cond(credit), timeout);
 
 		if (kthread_should_stop())
 			return 0;
@@ -543,22 +547,23 @@
 
 		if (credit > 0) {
 			if (balloon_is_inflated())
-				state = increase_reservation(credit);
+				balloon_state = increase_reservation(credit);
 			else
-				state = reserve_additional_memory();
+				balloon_state = reserve_additional_memory();
 		}
 
 		if (credit < 0) {
 			long n_pages;
 
 			n_pages = min(-credit, si_mem_available());
-			state = decrease_reservation(n_pages, GFP_BALLOON);
-			if (state == BP_DONE && n_pages != -credit &&
+			balloon_state = decrease_reservation(n_pages,
+							     GFP_BALLOON);
+			if (balloon_state == BP_DONE && n_pages != -credit &&
 			    n_pages < totalreserve_pages)
-				state = BP_EAGAIN;
+				balloon_state = BP_EAGAIN;
 		}
 
-		state = update_schedule(state);
+		update_schedule();
 
 		mutex_unlock(&balloon_mutex);
 
@@ -765,3 +770,38 @@
 	return 0;
 }
 subsys_initcall(balloon_init);
+
+static int __init balloon_wait_finish(void)
+{
+	long credit, last_credit = 0;
+	unsigned long last_changed = 0;
+
+	if (!xen_domain())
+		return -ENODEV;
+
+	/* PV guests don't need to wait. */
+	if (xen_pv_domain() || !current_credit())
+		return 0;
+
+	pr_notice("Waiting for initial ballooning down having finished.\n");
+
+	while ((credit = current_credit()) < 0) {
+		if (credit != last_credit) {
+			last_changed = jiffies;
+			last_credit = credit;
+		}
+		if (balloon_state == BP_ECANCELED) {
+			pr_warn_once("Initial ballooning failed, %ld pages need to be freed.\n",
+				     -credit);
+			if (jiffies - last_changed >= HZ * balloon_boot_timeout)
+				panic("Initial ballooning failed!\n");
+		}
+
+		schedule_timeout_interruptible(HZ / 10);
+	}
+
+	pr_notice("Initial ballooning down finished.\n");
+
+	return 0;
+}
+late_initcall_sync(balloon_wait_finish);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/events/events_base.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/events/events_base.c
@@ -33,6 +33,7 @@
 #include <linux/slab.h>
 #include <linux/irqnr.h>
 #include <linux/pci.h>
+#include <linux/rcupdate.h>
 #include <linux/spinlock.h>
 #include <linux/cpuhotplug.h>
 #include <linux/atomic.h>
@@ -95,6 +96,7 @@
 struct irq_info {
 	struct list_head list;
 	struct list_head eoi_list;
+	struct rcu_work rwork;
 	short refcnt;
 	u8 spurious_cnt;
 	u8 is_accounted;
@@ -145,22 +147,12 @@
 static DEFINE_MUTEX(irq_mapping_update_lock);
 
 /*
- * Lock protecting event handling loop against removing event channels.
- * Adding of event channels is no issue as the associated IRQ becomes active
- * only after everything is setup (before request_[threaded_]irq() the handler
- * can't be entered for an event, as the event channel will be unmasked only
- * then).
- */
-static DEFINE_RWLOCK(evtchn_rwlock);
-
-/*
  * Lock hierarchy:
  *
  * irq_mapping_update_lock
- *   evtchn_rwlock
- *     IRQ-desc lock
- *       percpu eoi_list_lock
- *         irq_info->lock
+ *   IRQ-desc lock
+ *     percpu eoi_list_lock
+ *       irq_info->lock
  */
 
 static LIST_HEAD(xen_irq_list_head);
@@ -304,6 +296,22 @@
 	info->is_accounted = 1;
 }
 
+static void delayed_free_irq(struct work_struct *work)
+{
+	struct irq_info *info = container_of(to_rcu_work(work), struct irq_info,
+					     rwork);
+	unsigned int irq = info->irq;
+
+	/* Remove the info pointer only now, with no potential users left. */
+	set_info_for_irq(irq, NULL);
+
+	kfree(info);
+
+	/* Legacy IRQ descriptors are managed by the arch. */
+	if (irq >= nr_legacy_irqs())
+		irq_free_desc(irq);
+}
+
 /* Constructors for packed IRQ information. */
 static int xen_irq_info_common_setup(struct irq_info *info,
 				     unsigned irq,
@@ -528,9 +536,10 @@
 	BUG_ON(irq == -1);
 
 	if (IS_ENABLED(CONFIG_SMP) && force_affinity) {
-		cpumask_copy(irq_get_affinity_mask(irq), cpumask_of(cpu));
-		cpumask_copy(irq_get_effective_affinity_mask(irq),
-			     cpumask_of(cpu));
+		struct irq_data *data = irq_get_irq_data(irq);
+
+		irq_data_update_affinity(data, cpumask_of(cpu));
+		irq_data_update_effective_affinity(data, cpumask_of(cpu));
 	}
 
 	xen_evtchn_port_bind_to_cpu(evtchn, cpu, info->cpu);
@@ -590,7 +599,9 @@
 
 	spin_lock_irqsave(&eoi->eoi_list_lock, flags);
 
-	if (list_empty(&eoi->eoi_list)) {
+	elem = list_first_entry_or_null(&eoi->eoi_list, struct irq_info,
+					eoi_list);
+	if (!elem || info->eoi_time < elem->eoi_time) {
 		list_add(&info->eoi_list, &eoi->eoi_list);
 		mod_delayed_work_on(info->eoi_cpu, system_wq,
 				    &eoi->delayed, delay);
@@ -665,33 +676,36 @@
 
 	eoi = container_of(to_delayed_work(work), struct lateeoi_work, delayed);
 
-	read_lock_irqsave(&evtchn_rwlock, flags);
+	rcu_read_lock();
 
 	while (true) {
-		spin_lock(&eoi->eoi_list_lock);
+		spin_lock_irqsave(&eoi->eoi_list_lock, flags);
 
 		info = list_first_entry_or_null(&eoi->eoi_list, struct irq_info,
 						eoi_list);
 
-		if (info == NULL || now < info->eoi_time) {
-			spin_unlock(&eoi->eoi_list_lock);
+		if (info == NULL)
+			break;
+
+		if (now < info->eoi_time) {
+			mod_delayed_work_on(info->eoi_cpu, system_wq,
+					    &eoi->delayed,
+					    info->eoi_time - now);
 			break;
 		}
 
 		list_del_init(&info->eoi_list);
 
-		spin_unlock(&eoi->eoi_list_lock);
+		spin_unlock_irqrestore(&eoi->eoi_list_lock, flags);
 
 		info->eoi_time = 0;
 
 		xen_irq_lateeoi_locked(info, false);
 	}
 
-	if (info)
-		mod_delayed_work_on(info->eoi_cpu, system_wq,
-				    &eoi->delayed, info->eoi_time - now);
+	spin_unlock_irqrestore(&eoi->eoi_list_lock, flags);
 
-	read_unlock_irqrestore(&evtchn_rwlock, flags);
+	rcu_read_unlock();
 }
 
 static void xen_cpu_init_eoi(unsigned int cpu)
@@ -706,16 +720,15 @@
 void xen_irq_lateeoi(unsigned int irq, unsigned int eoi_flags)
 {
 	struct irq_info *info;
-	unsigned long flags;
 
-	read_lock_irqsave(&evtchn_rwlock, flags);
+	rcu_read_lock();
 
 	info = info_for_irq(irq);
 
 	if (info)
 		xen_irq_lateeoi_locked(info, eoi_flags & XEN_EOI_FLAG_SPURIOUS);
 
-	read_unlock_irqrestore(&evtchn_rwlock, flags);
+	rcu_read_unlock();
 }
 EXPORT_SYMBOL_GPL(xen_irq_lateeoi);
 
@@ -729,6 +742,7 @@
 
 	info->type = IRQT_UNBOUND;
 	info->refcnt = -1;
+	INIT_RCU_WORK(&info->rwork, delayed_free_irq);
 
 	set_info_for_irq(irq, info);
 	/*
@@ -786,31 +800,18 @@
 static void xen_free_irq(unsigned irq)
 {
 	struct irq_info *info = info_for_irq(irq);
-	unsigned long flags;
 
 	if (WARN_ON(!info))
 		return;
 
-	write_lock_irqsave(&evtchn_rwlock, flags);
-
 	if (!list_empty(&info->eoi_list))
 		lateeoi_list_del(info);
 
 	list_del(&info->list);
 
-	set_info_for_irq(irq, NULL);
-
 	WARN_ON(info->refcnt > 0);
 
-	write_unlock_irqrestore(&evtchn_rwlock, flags);
-
-	kfree(info);
-
-	/* Legacy IRQ descriptors are managed by the arch. */
-	if (irq < nr_legacy_irqs())
-		return;
-
-	irq_free_desc(irq);
+	queue_rcu_work(system_wq, &info->rwork);
 }
 
 static void xen_evtchn_close(evtchn_port_t port)
@@ -935,8 +936,8 @@
 		return;
 
 	do_mask(info, EVT_MASK_REASON_EXPLICIT);
-	xen_evtchn_close(evtchn);
 	xen_irq_info_cleanup(info);
+	xen_evtchn_close(evtchn);
 }
 
 static void enable_pirq(struct irq_data *data)
@@ -980,8 +981,6 @@
 		unsigned int cpu = cpu_from_irq(irq);
 		struct xenbus_device *dev;
 
-		xen_evtchn_close(evtchn);
-
 		switch (type_from_irq(irq)) {
 		case IRQT_VIRQ:
 			per_cpu(virq_to_irq, cpu)[virq_from_irq(irq)] = -1;
@@ -999,6 +998,7 @@
 		}
 
 		xen_irq_info_cleanup(info);
+		xen_evtchn_close(evtchn);
 	}
 
 	xen_free_irq(irq);
@@ -1251,6 +1251,12 @@
 }
 EXPORT_SYMBOL_GPL(bind_evtchn_to_irq);
 
+int bind_evtchn_to_irq_lateeoi(evtchn_port_t evtchn)
+{
+	return bind_evtchn_to_irq_chip(evtchn, &xen_lateeoi_chip, NULL);
+}
+EXPORT_SYMBOL_GPL(bind_evtchn_to_irq_lateeoi);
+
 static int bind_ipi_to_irq(unsigned int ipi, unsigned int cpu)
 {
 	struct evtchn_bind_ipi bind_ipi;
@@ -1708,7 +1714,14 @@
 	int cpu = smp_processor_id();
 	struct evtchn_loop_ctrl ctrl = { 0 };
 
-	read_lock(&evtchn_rwlock);
+	/*
+	 * When closing an event channel the associated IRQ must not be freed
+	 * until all cpus have left the event handling loop. This is ensured
+	 * by taking the rcu_read_lock() while handling events, as freeing of
+	 * the IRQ is handled via queue_rcu_work() _after_ closing the event
+	 * channel.
+	 */
+	rcu_read_lock();
 
 	do {
 		vcpu_info->evtchn_upcall_pending = 0;
@@ -1721,7 +1734,7 @@
 
 	} while (vcpu_info->evtchn_upcall_pending);
 
-	read_unlock(&evtchn_rwlock);
+	rcu_read_unlock();
 
 	/*
 	 * Increment irq_epoch only now to defer EOIs only for
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/features.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/features.c
@@ -42,7 +42,7 @@
 		if (HYPERVISOR_xen_version(XENVER_get_features, &fi) < 0)
 			break;
 		for (j = 0; j < 32; j++)
-			xen_features[i * 32 + j] = !!(fi.submap & 1<<j);
+			xen_features[i * 32 + j] = !!(fi.submap & 1U << j);
 	}
 
 	if (xen_pv_domain()) {
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/gntalloc.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/gntalloc.c
@@ -169,20 +169,14 @@
 		__del_gref(gref);
 	}
 
-	/* It's possible for the target domain to map the just-allocated grant
-	 * references by blindly guessing their IDs; if this is done, then
-	 * __del_gref will leave them in the queue_gref list. They need to be
-	 * added to the global list so that we can free them when they are no
-	 * longer referenced.
-	 */
-	if (unlikely(!list_empty(&queue_gref)))
-		list_splice_tail(&queue_gref, &gref_list);
 	mutex_unlock(&gref_mutex);
 	return rc;
 }
 
 static void __del_gref(struct gntalloc_gref *gref)
 {
+	unsigned long addr;
+
 	if (gref->notify.flags & UNMAP_NOTIFY_CLEAR_BYTE) {
 		uint8_t *tmp = kmap(gref->page);
 		tmp[gref->notify.pgoff] = 0;
@@ -196,21 +190,16 @@
 	gref->notify.flags = 0;
 
 	if (gref->gref_id) {
-		if (gnttab_query_foreign_access(gref->gref_id))
-			return;
-
-		if (!gnttab_end_foreign_access_ref(gref->gref_id, 0))
-			return;
-
-		gnttab_free_grant_reference(gref->gref_id);
+		if (gref->page) {
+			addr = (unsigned long)page_to_virt(gref->page);
+			gnttab_end_foreign_access(gref->gref_id, 0, addr);
+		} else
+			gnttab_free_grant_reference(gref->gref_id);
 	}
 
 	gref_size--;
 	list_del(&gref->next_gref);
 
-	if (gref->page)
-		__free_page(gref->page);
-
 	kfree(gref);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/gntdev-common.h
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/gntdev-common.h
@@ -16,6 +16,7 @@
 #include <linux/mmu_notifier.h>
 #include <linux/types.h>
 #include <xen/interface/event_channel.h>
+#include <xen/grant_table.h>
 
 struct gntdev_dmabuf_priv;
 
@@ -43,9 +44,10 @@
 };
 
 struct gntdev_grant_map {
+	atomic_t in_use;
 	struct mmu_interval_notifier notifier;
+	bool notifier_init;
 	struct list_head next;
-	struct vm_area_struct *vma;
 	int index;
 	int count;
 	int flags;
@@ -56,6 +58,7 @@
 	struct gnttab_unmap_grant_ref *unmap_ops;
 	struct gnttab_map_grant_ref   *kmap_ops;
 	struct gnttab_unmap_grant_ref *kunmap_ops;
+	bool *being_removed;
 	struct page **pages;
 	unsigned long pages_vm_start;
 
@@ -73,6 +76,11 @@
 	/* Needed to avoid allocation in gnttab_dma_free_pages(). */
 	xen_pfn_t *frames;
 #endif
+
+	/* Number of live grants */
+	atomic_t live_grants;
+	/* Needed to avoid allocation in __unmap_grant_pages */
+	struct gntab_unmap_queue_data unmap_data;
 };
 
 struct gntdev_grant_map *gntdev_alloc_map(struct gntdev_priv *priv, int count,
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/gntdev-dmabuf.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/gntdev-dmabuf.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/errno.h>
 #include <linux/dma-buf.h>
+#include <linux/dma-direct.h>
 #include <linux/slab.h>
 #include <linux/types.h>
 #include <linux/uaccess.h>
@@ -56,7 +57,7 @@
 
 	/* Number of pages this buffer has. */
 	int nr_pages;
-	/* Pages of this buffer. */
+	/* Pages of this buffer (only for dma-buf export). */
 	struct page **pages;
 };
 
@@ -490,7 +491,7 @@
 /* DMA buffer import support. */
 
 static int
-dmabuf_imp_grant_foreign_access(struct page **pages, u32 *refs,
+dmabuf_imp_grant_foreign_access(unsigned long *gfns, u32 *refs,
 				int count, int domid)
 {
 	grant_ref_t priv_gref_head;
@@ -513,7 +514,7 @@
 		}
 
 		gnttab_grant_foreign_access_ref(cur_ref, domid,
-						xen_page_to_gfn(pages[i]), 0);
+						gfns[i], 0);
 		refs[i] = cur_ref;
 	}
 
@@ -535,7 +536,6 @@
 
 static void dmabuf_imp_free_storage(struct gntdev_dmabuf *gntdev_dmabuf)
 {
-	kfree(gntdev_dmabuf->pages);
 	kfree(gntdev_dmabuf->u.imp.refs);
 	kfree(gntdev_dmabuf);
 }
@@ -555,12 +555,6 @@
 	if (!gntdev_dmabuf->u.imp.refs)
 		goto fail;
 
-	gntdev_dmabuf->pages = kcalloc(count,
-				       sizeof(gntdev_dmabuf->pages[0]),
-				       GFP_KERNEL);
-	if (!gntdev_dmabuf->pages)
-		goto fail;
-
 	gntdev_dmabuf->nr_pages = count;
 
 	for (i = 0; i < count; i++)
@@ -582,7 +576,8 @@
 	struct dma_buf *dma_buf;
 	struct dma_buf_attachment *attach;
 	struct sg_table *sgt;
-	struct sg_page_iter sg_iter;
+	struct sg_dma_page_iter sg_iter;
+	unsigned long *gfns;
 	int i;
 
 	dma_buf = dma_buf_get(fd);
@@ -630,26 +625,31 @@
 
 	gntdev_dmabuf->u.imp.sgt = sgt;
 
-	/* Now convert sgt to array of pages and check for page validity. */
+	gfns = kcalloc(count, sizeof(*gfns), GFP_KERNEL);
+	if (!gfns) {
+		ret = ERR_PTR(-ENOMEM);
+		goto fail_unmap;
+	}
+
+	/*
+	 * Now convert sgt to array of gfns without accessing underlying pages.
+	 * It is not allowed to access the underlying struct page of an sg table
+	 * exported by DMA-buf, but since we deal with special Xen dma device here
+	 * (not a normal physical one) look at the dma addresses in the sg table
+	 * and then calculate gfns directly from them.
+	 */
 	i = 0;
-	for_each_sgtable_page(sgt, &sg_iter, 0) {
-		struct page *page = sg_page_iter_page(&sg_iter);
-		/*
-		 * Check if page is valid: this can happen if we are given
-		 * a page from VRAM or other resources which are not backed
-		 * by a struct page.
-		 */
-		if (!pfn_valid(page_to_pfn(page))) {
-			ret = ERR_PTR(-EINVAL);
-			goto fail_unmap;
-		}
+	for_each_sgtable_dma_page(sgt, &sg_iter, 0) {
+		dma_addr_t addr = sg_page_iter_dma_address(&sg_iter);
+		unsigned long pfn = bfn_to_pfn(XEN_PFN_DOWN(dma_to_phys(dev, addr)));
 
-		gntdev_dmabuf->pages[i++] = page;
+		gfns[i++] = pfn_to_gfn(pfn);
 	}
 
-	ret = ERR_PTR(dmabuf_imp_grant_foreign_access(gntdev_dmabuf->pages,
+	ret = ERR_PTR(dmabuf_imp_grant_foreign_access(gfns,
 						      gntdev_dmabuf->u.imp.refs,
 						      count, domid));
+	kfree(gfns);
 	if (IS_ERR(ret))
 		goto fail_end_access;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/gntdev.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/gntdev.c
@@ -35,6 +35,7 @@
 #include <linux/slab.h>
 #include <linux/highmem.h>
 #include <linux/refcount.h>
+#include <linux/workqueue.h>
 
 #include <xen/xen.h>
 #include <xen/grant_table.h>
@@ -60,10 +61,11 @@
 MODULE_PARM_DESC(limit,
 	"Maximum number of grants that may be mapped by one mapping request");
 
+/* True in PV mode, false otherwise */
 static int use_ptemod;
 
-static int unmap_grant_pages(struct gntdev_grant_map *map,
-			     int offset, int pages);
+static void unmap_grant_pages(struct gntdev_grant_map *map,
+			      int offset, int pages);
 
 static struct miscdevice gntdev_miscdev;
 
@@ -120,6 +122,7 @@
 	kvfree(map->unmap_ops);
 	kvfree(map->kmap_ops);
 	kvfree(map->kunmap_ops);
+	kvfree(map->being_removed);
 	kfree(map);
 }
 
@@ -140,10 +143,13 @@
 	add->unmap_ops = kvmalloc_array(count, sizeof(add->unmap_ops[0]),
 					GFP_KERNEL);
 	add->pages     = kvcalloc(count, sizeof(add->pages[0]), GFP_KERNEL);
+	add->being_removed =
+		kvcalloc(count, sizeof(add->being_removed[0]), GFP_KERNEL);
 	if (NULL == add->grants    ||
 	    NULL == add->map_ops   ||
 	    NULL == add->unmap_ops ||
-	    NULL == add->pages)
+	    NULL == add->pages     ||
+	    NULL == add->being_removed)
 		goto err;
 	if (use_ptemod) {
 		add->kmap_ops   = kvmalloc_array(count, sizeof(add->kmap_ops[0]),
@@ -250,13 +256,43 @@
 	if (!refcount_dec_and_test(&map->users))
 		return;
 
+	if (map->pages && !use_ptemod) {
+		/*
+		 * Increment the reference count.  This ensures that the
+		 * subsequent call to unmap_grant_pages() will not wind up
+		 * re-entering itself.  It *can* wind up calling
+		 * gntdev_put_map() recursively, but such calls will be with a
+		 * reference count greater than 1, so they will return before
+		 * this code is reached.  The recursion depth is thus limited to
+		 * 1.  Do NOT use refcount_inc() here, as it will detect that
+		 * the reference count is zero and WARN().
+		 */
+		refcount_set(&map->users, 1);
+
+		/*
+		 * Unmap the grants.  This may or may not be asynchronous, so it
+		 * is possible that the reference count is 1 on return, but it
+		 * could also be greater than 1.
+		 */
+		unmap_grant_pages(map, 0, map->count);
+
+		/* Check if the memory now needs to be freed */
+		if (!refcount_dec_and_test(&map->users))
+			return;
+
+		/*
+		 * All pages have been returned to the hypervisor, so free the
+		 * map.
+		 */
+	}
+
+	if (use_ptemod && map->notifier_init)
+		mmu_interval_notifier_remove(&map->notifier);
+
 	if (map->notify.flags & UNMAP_NOTIFY_SEND_EVENT) {
 		notify_remote_via_evtchn(map->notify.event);
 		evtchn_put(map->notify.event);
 	}
-
-	if (map->pages && !use_ptemod)
-		unmap_grant_pages(map, 0, map->count);
 	gntdev_free_map(map);
 }
 
@@ -265,7 +301,7 @@
 static int find_grant_ptes(pte_t *pte, unsigned long addr, void *data)
 {
 	struct gntdev_grant_map *map = data;
-	unsigned int pgnr = (addr - map->vma->vm_start) >> PAGE_SHIFT;
+	unsigned int pgnr = (addr - map->pages_vm_start) >> PAGE_SHIFT;
 	int flags = map->flags | GNTMAP_application_map | GNTMAP_contains_pte |
 		    (1 << _GNTMAP_guest_avail0);
 	u64 pte_maddr;
@@ -283,6 +319,7 @@
 
 int gntdev_map_grant_pages(struct gntdev_grant_map *map)
 {
+	size_t alloced = 0;
 	int i, err = 0;
 
 	if (!use_ptemod) {
@@ -331,97 +368,130 @@
 			map->count);
 
 	for (i = 0; i < map->count; i++) {
-		if (map->map_ops[i].status == GNTST_okay)
+		if (map->map_ops[i].status == GNTST_okay) {
 			map->unmap_ops[i].handle = map->map_ops[i].handle;
-		else if (!err)
+			alloced++;
+		} else if (!err)
 			err = -EINVAL;
 
 		if (map->flags & GNTMAP_device_map)
 			map->unmap_ops[i].dev_bus_addr = map->map_ops[i].dev_bus_addr;
 
 		if (use_ptemod) {
-			if (map->kmap_ops[i].status == GNTST_okay)
+			if (map->kmap_ops[i].status == GNTST_okay) {
+				alloced++;
 				map->kunmap_ops[i].handle = map->kmap_ops[i].handle;
-			else if (!err)
+			} else if (!err)
 				err = -EINVAL;
 		}
 	}
+	atomic_add(alloced, &map->live_grants);
 	return err;
 }
 
-static int __unmap_grant_pages(struct gntdev_grant_map *map, int offset,
-			       int pages)
+static void __unmap_grant_pages_done(int result,
+		struct gntab_unmap_queue_data *data)
 {
-	int i, err = 0;
-	struct gntab_unmap_queue_data unmap_data;
-
-	if (map->notify.flags & UNMAP_NOTIFY_CLEAR_BYTE) {
-		int pgno = (map->notify.addr >> PAGE_SHIFT);
-		if (pgno >= offset && pgno < offset + pages) {
-			/* No need for kmap, pages are in lowmem */
-			uint8_t *tmp = pfn_to_kaddr(page_to_pfn(map->pages[pgno]));
-			tmp[map->notify.addr & (PAGE_SIZE-1)] = 0;
-			map->notify.flags &= ~UNMAP_NOTIFY_CLEAR_BYTE;
-		}
-	}
-
-	unmap_data.unmap_ops = map->unmap_ops + offset;
-	unmap_data.kunmap_ops = use_ptemod ? map->kunmap_ops + offset : NULL;
-	unmap_data.pages = map->pages + offset;
-	unmap_data.count = pages;
-
-	err = gnttab_unmap_refs_sync(&unmap_data);
-	if (err)
-		return err;
+	unsigned int i;
+	struct gntdev_grant_map *map = data->data;
+	unsigned int offset = data->unmap_ops - map->unmap_ops;
+	int successful_unmaps = 0;
+	int live_grants;
+
+	for (i = 0; i < data->count; i++) {
+		if (map->unmap_ops[offset + i].status == GNTST_okay &&
+		    map->unmap_ops[offset + i].handle != INVALID_GRANT_HANDLE)
+			successful_unmaps++;
 
-	for (i = 0; i < pages; i++) {
-		if (map->unmap_ops[offset+i].status)
-			err = -EINVAL;
+		WARN_ON(map->unmap_ops[offset + i].status != GNTST_okay &&
+			map->unmap_ops[offset + i].handle != INVALID_GRANT_HANDLE);
 		pr_debug("unmap handle=%d st=%d\n",
 			map->unmap_ops[offset+i].handle,
 			map->unmap_ops[offset+i].status);
 		map->unmap_ops[offset+i].handle = INVALID_GRANT_HANDLE;
 		if (use_ptemod) {
-			if (map->kunmap_ops[offset+i].status)
-				err = -EINVAL;
+			if (map->kunmap_ops[offset + i].status == GNTST_okay &&
+			    map->kunmap_ops[offset + i].handle != INVALID_GRANT_HANDLE)
+				successful_unmaps++;
+
+			WARN_ON(map->kunmap_ops[offset + i].status != GNTST_okay &&
+				map->kunmap_ops[offset + i].handle != INVALID_GRANT_HANDLE);
 			pr_debug("kunmap handle=%u st=%d\n",
 				 map->kunmap_ops[offset+i].handle,
 				 map->kunmap_ops[offset+i].status);
 			map->kunmap_ops[offset+i].handle = INVALID_GRANT_HANDLE;
 		}
 	}
-	return err;
+
+	/*
+	 * Decrease the live-grant counter.  This must happen after the loop to
+	 * prevent premature reuse of the grants by gnttab_mmap().
+	 */
+	live_grants = atomic_sub_return(successful_unmaps, &map->live_grants);
+	if (WARN_ON(live_grants < 0))
+		pr_err("%s: live_grants became negative (%d) after unmapping %d pages!\n",
+		       __func__, live_grants, successful_unmaps);
+
+	/* Release reference taken by __unmap_grant_pages */
+	gntdev_put_map(NULL, map);
+}
+
+static void __unmap_grant_pages(struct gntdev_grant_map *map, int offset,
+			       int pages)
+{
+	if (map->notify.flags & UNMAP_NOTIFY_CLEAR_BYTE) {
+		int pgno = (map->notify.addr >> PAGE_SHIFT);
+
+		if (pgno >= offset && pgno < offset + pages) {
+			/* No need for kmap, pages are in lowmem */
+			uint8_t *tmp = pfn_to_kaddr(page_to_pfn(map->pages[pgno]));
+
+			tmp[map->notify.addr & (PAGE_SIZE-1)] = 0;
+			map->notify.flags &= ~UNMAP_NOTIFY_CLEAR_BYTE;
+		}
+	}
+
+	map->unmap_data.unmap_ops = map->unmap_ops + offset;
+	map->unmap_data.kunmap_ops = use_ptemod ? map->kunmap_ops + offset : NULL;
+	map->unmap_data.pages = map->pages + offset;
+	map->unmap_data.count = pages;
+	map->unmap_data.done = __unmap_grant_pages_done;
+	map->unmap_data.data = map;
+	refcount_inc(&map->users); /* to keep map alive during async call below */
+
+	gnttab_unmap_refs_async(&map->unmap_data);
 }
 
-static int unmap_grant_pages(struct gntdev_grant_map *map, int offset,
-			     int pages)
+static void unmap_grant_pages(struct gntdev_grant_map *map, int offset,
+			      int pages)
 {
-	int range, err = 0;
+	int range;
+
+	if (atomic_read(&map->live_grants) == 0)
+		return; /* Nothing to do */
 
 	pr_debug("unmap %d+%d [%d+%d]\n", map->index, map->count, offset, pages);
 
 	/* It is possible the requested range will have a "hole" where we
 	 * already unmapped some of the grants. Only unmap valid ranges.
 	 */
-	while (pages && !err) {
-		while (pages &&
-		       map->unmap_ops[offset].handle == INVALID_GRANT_HANDLE) {
+	while (pages) {
+		while (pages && map->being_removed[offset]) {
 			offset++;
 			pages--;
 		}
 		range = 0;
 		while (range < pages) {
-			if (map->unmap_ops[offset + range].handle ==
-			    INVALID_GRANT_HANDLE)
+			if (map->being_removed[offset + range])
 				break;
+			map->being_removed[offset + range] = true;
 			range++;
 		}
-		err = __unmap_grant_pages(map, offset, range);
+		if (range)
+			__unmap_grant_pages(map, offset, range);
 		offset += range;
 		pages -= range;
 	}
-
-	return err;
 }
 
 /* ------------------------------------------------------------------ */
@@ -441,11 +511,7 @@
 	struct gntdev_priv *priv = file->private_data;
 
 	pr_debug("gntdev_vma_close %p\n", vma);
-	if (use_ptemod) {
-		WARN_ON(map->vma != vma);
-		mmu_interval_notifier_remove(&map->notifier);
-		map->vma = NULL;
-	}
+
 	vma->vm_private_data = NULL;
 	gntdev_put_map(priv, map);
 }
@@ -473,31 +539,30 @@
 	struct gntdev_grant_map *map =
 		container_of(mn, struct gntdev_grant_map, notifier);
 	unsigned long mstart, mend;
-	int err;
+	unsigned long map_start, map_end;
 
 	if (!mmu_notifier_range_blockable(range))
 		return false;
 
+	map_start = map->pages_vm_start;
+	map_end = map->pages_vm_start + (map->count << PAGE_SHIFT);
+
 	/*
 	 * If the VMA is split or otherwise changed the notifier is not
 	 * updated, but we don't want to process VA's outside the modified
 	 * VMA. FIXME: It would be much more understandable to just prevent
 	 * modifying the VMA in the first place.
 	 */
-	if (map->vma->vm_start >= range->end ||
-	    map->vma->vm_end <= range->start)
+	if (map_start >= range->end || map_end <= range->start)
 		return true;
 
-	mstart = max(range->start, map->vma->vm_start);
-	mend = min(range->end, map->vma->vm_end);
+	mstart = max(range->start, map_start);
+	mend = min(range->end, map_end);
 	pr_debug("map %d+%d (%lx %lx), range %lx %lx, mrange %lx %lx\n",
-			map->index, map->count,
-			map->vma->vm_start, map->vma->vm_end,
-			range->start, range->end, mstart, mend);
-	err = unmap_grant_pages(map,
-				(mstart - map->vma->vm_start) >> PAGE_SHIFT,
-				(mend - mstart) >> PAGE_SHIFT);
-	WARN_ON(err);
+		 map->index, map->count, map_start, map_end,
+		 range->start, range->end, mstart, mend);
+	unmap_grant_pages(map, (mstart - map_start) >> PAGE_SHIFT,
+			  (mend - mstart) >> PAGE_SHIFT);
 
 	return true;
 }
@@ -977,14 +1042,15 @@
 		return -EINVAL;
 
 	pr_debug("map %d+%d at %lx (pgoff %lx)\n",
-			index, count, vma->vm_start, vma->vm_pgoff);
+		 index, count, vma->vm_start, vma->vm_pgoff);
 
 	mutex_lock(&priv->lock);
 	map = gntdev_find_map_index(priv, index, count);
 	if (!map)
 		goto unlock_out;
-	if (use_ptemod && map->vma)
+	if (!atomic_add_unless(&map->in_use, 1, 1))
 		goto unlock_out;
+
 	refcount_inc(&map->users);
 
 	vma->vm_ops = &gntdev_vmops;
@@ -1005,15 +1071,16 @@
 			map->flags |= GNTMAP_readonly;
 	}
 
+	map->pages_vm_start = vma->vm_start;
+
 	if (use_ptemod) {
-		map->vma = vma;
 		err = mmu_interval_notifier_insert_locked(
 			&map->notifier, vma->vm_mm, vma->vm_start,
 			vma->vm_end - vma->vm_start, &gntdev_mmu_ops);
-		if (err) {
-			map->vma = NULL;
+		if (err)
 			goto out_unlock_put;
-		}
+
+		map->notifier_init = true;
 	}
 	mutex_unlock(&priv->lock);
 
@@ -1030,7 +1097,6 @@
 		 */
 		mmu_interval_read_begin(&map->notifier);
 
-		map->pages_vm_start = vma->vm_start;
 		err = apply_to_page_range(vma->vm_mm, vma->vm_start,
 					  vma->vm_end - vma->vm_start,
 					  find_grant_ptes, map);
@@ -1059,13 +1125,8 @@
 out_unlock_put:
 	mutex_unlock(&priv->lock);
 out_put_map:
-	if (use_ptemod) {
+	if (use_ptemod)
 		unmap_grant_pages(map, 0, map->count);
-		if (map->vma) {
-			mmu_interval_notifier_remove(&map->notifier);
-			map->vma = NULL;
-		}
-	}
 	gntdev_put_map(priv, map);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/grant-table.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/grant-table.c
@@ -134,12 +134,9 @@
 	 */
 	unsigned long (*end_foreign_transfer_ref)(grant_ref_t ref);
 	/*
-	 * Query the status of a grant entry. Ref parameter is reference of
-	 * queried grant entry, return value is the status of queried entry.
-	 * Detailed status(writing/reading) can be gotten from the return value
-	 * by bit operations.
+	 * Read the frame number related to a given grant reference.
 	 */
-	int (*query_foreign_access)(grant_ref_t ref);
+	unsigned long (*read_frame)(grant_ref_t ref);
 };
 
 struct unmap_refs_callback_data {
@@ -284,22 +281,6 @@
 }
 EXPORT_SYMBOL_GPL(gnttab_grant_foreign_access);
 
-static int gnttab_query_foreign_access_v1(grant_ref_t ref)
-{
-	return gnttab_shared.v1[ref].flags & (GTF_reading|GTF_writing);
-}
-
-static int gnttab_query_foreign_access_v2(grant_ref_t ref)
-{
-	return grstatus[ref] & (GTF_reading|GTF_writing);
-}
-
-int gnttab_query_foreign_access(grant_ref_t ref)
-{
-	return gnttab_interface->query_foreign_access(ref);
-}
-EXPORT_SYMBOL_GPL(gnttab_query_foreign_access);
-
 static int gnttab_end_foreign_access_ref_v1(grant_ref_t ref, int readonly)
 {
 	u16 flags, nflags;
@@ -353,6 +334,16 @@
 }
 EXPORT_SYMBOL_GPL(gnttab_end_foreign_access_ref);
 
+static unsigned long gnttab_read_frame_v1(grant_ref_t ref)
+{
+	return gnttab_shared.v1[ref].frame;
+}
+
+static unsigned long gnttab_read_frame_v2(grant_ref_t ref)
+{
+	return gnttab_shared.v2[ref].full_page.frame;
+}
+
 struct deferred_entry {
 	struct list_head list;
 	grant_ref_t ref;
@@ -382,12 +373,9 @@
 		spin_unlock_irqrestore(&gnttab_list_lock, flags);
 		if (_gnttab_end_foreign_access_ref(entry->ref, entry->ro)) {
 			put_free_entry(entry->ref);
-			if (entry->page) {
-				pr_debug("freeing g.e. %#x (pfn %#lx)\n",
-					 entry->ref, page_to_pfn(entry->page));
-				put_page(entry->page);
-			} else
-				pr_info("freeing g.e. %#x\n", entry->ref);
+			pr_debug("freeing g.e. %#x (pfn %#lx)\n",
+				 entry->ref, page_to_pfn(entry->page));
+			put_page(entry->page);
 			kfree(entry);
 			entry = NULL;
 		} else {
@@ -412,9 +400,18 @@
 static void gnttab_add_deferred(grant_ref_t ref, bool readonly,
 				struct page *page)
 {
-	struct deferred_entry *entry = kmalloc(sizeof(*entry), GFP_ATOMIC);
+	struct deferred_entry *entry;
+	gfp_t gfp = (in_atomic() || irqs_disabled()) ? GFP_ATOMIC : GFP_KERNEL;
 	const char *what = KERN_WARNING "leaking";
 
+	entry = kmalloc(sizeof(*entry), gfp);
+	if (!page) {
+		unsigned long gfn = gnttab_interface->read_frame(ref);
+
+		page = pfn_to_page(gfn_to_pfn(gfn));
+		get_page(page);
+	}
+
 	if (entry) {
 		unsigned long flags;
 
@@ -435,11 +432,21 @@
 	       what, ref, page ? page_to_pfn(page) : -1);
 }
 
+int gnttab_try_end_foreign_access(grant_ref_t ref)
+{
+	int ret = _gnttab_end_foreign_access_ref(ref, 0);
+
+	if (ret)
+		put_free_entry(ref);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(gnttab_try_end_foreign_access);
+
 void gnttab_end_foreign_access(grant_ref_t ref, int readonly,
 			       unsigned long page)
 {
-	if (gnttab_end_foreign_access_ref(ref, readonly)) {
-		put_free_entry(ref);
+	if (gnttab_try_end_foreign_access(ref)) {
 		if (page != 0)
 			put_page(virt_to_page(page));
 	} else
@@ -974,6 +981,9 @@
 	size_t size;
 	int i, ret;
 
+	if (args->nr_pages < 0 || args->nr_pages > (INT_MAX >> PAGE_SHIFT))
+		return -ENOMEM;
+
 	size = args->nr_pages << PAGE_SHIFT;
 	if (args->coherent)
 		args->vaddr = dma_alloc_coherent(args->dev, size,
@@ -1417,7 +1427,7 @@
 	.update_entry			= gnttab_update_entry_v1,
 	.end_foreign_access_ref		= gnttab_end_foreign_access_ref_v1,
 	.end_foreign_transfer_ref	= gnttab_end_foreign_transfer_ref_v1,
-	.query_foreign_access		= gnttab_query_foreign_access_v1,
+	.read_frame			= gnttab_read_frame_v1,
 };
 
 static const struct gnttab_ops gnttab_v2_ops = {
@@ -1429,7 +1439,7 @@
 	.update_entry			= gnttab_update_entry_v2,
 	.end_foreign_access_ref		= gnttab_end_foreign_access_ref_v2,
 	.end_foreign_transfer_ref	= gnttab_end_foreign_transfer_ref_v2,
-	.query_foreign_access		= gnttab_query_foreign_access_v2,
+	.read_frame			= gnttab_read_frame_v2,
 };
 
 static bool gnttab_need_v2(void)
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/pcpu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/pcpu.c
@@ -58,6 +58,7 @@
 	struct list_head list;
 	struct device dev;
 	uint32_t cpu_id;
+	uint32_t acpi_id;
 	uint32_t flags;
 };
 
@@ -228,7 +229,7 @@
 
 	err = device_register(dev);
 	if (err) {
-		pcpu_release(dev);
+		put_device(dev);
 		return err;
 	}
 
@@ -249,6 +250,7 @@
 
 	INIT_LIST_HEAD(&pcpu->list);
 	pcpu->cpu_id = info->xen_cpuid;
+	pcpu->acpi_id = info->acpi_id;
 	pcpu->flags = info->flags;
 
 	/* Need hold on xen_pcpu_lock before pcpu list manipulations */
@@ -381,3 +383,21 @@
 	return ret;
 }
 arch_initcall(xen_pcpu_init);
+
+#ifdef CONFIG_ACPI
+bool __init xen_processor_present(uint32_t acpi_id)
+{
+	const struct pcpu *pcpu;
+	bool online = false;
+
+	mutex_lock(&xen_pcpu_lock);
+	list_for_each_entry(pcpu, &xen_pcpus, list)
+		if (pcpu->acpi_id == acpi_id) {
+			online = pcpu->flags & XEN_PCPU_FLAGS_ONLINE;
+			break;
+		}
+	mutex_unlock(&xen_pcpu_lock);
+
+	return online;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/platform-pci.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/platform-pci.c
@@ -144,7 +144,7 @@
 		if (ret) {
 			dev_warn(&pdev->dev, "Unable to set the evtchn callback "
 					 "err=%d\n", ret);
-			goto out;
+			goto irq_out;
 		}
 	}
 
@@ -152,13 +152,16 @@
 	grant_frames = alloc_xen_mmio(PAGE_SIZE * max_nr_gframes);
 	ret = gnttab_setup_auto_xlat_frames(grant_frames);
 	if (ret)
-		goto out;
+		goto irq_out;
 	ret = gnttab_init();
 	if (ret)
 		goto grant_out;
 	return 0;
 grant_out:
 	gnttab_free_auto_xlat_frames();
+irq_out:
+	if (!xen_have_vector_callback)
+		free_irq(pdev->irq, pdev);
 out:
 	pci_release_region(pdev, 0);
 mem_out:
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/privcmd.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/privcmd.c
@@ -581,27 +581,30 @@
 	struct privcmd_dm_op_buf kbufs[], unsigned int num,
 	struct page *pages[], unsigned int nr_pages, unsigned int *pinned)
 {
-	unsigned int i;
+	unsigned int i, off = 0;
 
-	for (i = 0; i < num; i++) {
+	for (i = 0; i < num; ) {
 		unsigned int requested;
 		int page_count;
 
 		requested = DIV_ROUND_UP(
 			offset_in_page(kbufs[i].uptr) + kbufs[i].size,
-			PAGE_SIZE);
+			PAGE_SIZE) - off;
 		if (requested > nr_pages)
 			return -ENOSPC;
 
 		page_count = pin_user_pages_fast(
-			(unsigned long) kbufs[i].uptr,
+			(unsigned long)kbufs[i].uptr + off * PAGE_SIZE,
 			requested, FOLL_WRITE, pages);
-		if (page_count < 0)
-			return page_count;
+		if (page_count <= 0)
+			return page_count ? : -EFAULT;
 
 		*pinned += page_count;
 		nr_pages -= page_count;
 		pages += page_count;
+
+		off = (requested == page_count) ? 0 : off + page_count;
+		i += !off;
 	}
 
 	return 0;
@@ -677,10 +680,8 @@
 	}
 
 	rc = lock_pages(kbufs, kdata.num, pages, nr_pages, &pinned);
-	if (rc < 0) {
-		nr_pages = pinned;
+	if (rc < 0)
 		goto out;
-	}
 
 	for (i = 0; i < kdata.num; i++) {
 		set_xen_guest_handle(xbufs[i].h, kbufs[i].uptr);
@@ -692,7 +693,7 @@
 	xen_preemptible_hcall_end();
 
 out:
-	unlock_pages(pages, nr_pages);
+	unlock_pages(pages, pinned);
 	kfree(xbufs);
 	kfree(pages);
 	kfree(kbufs);
@@ -759,7 +760,7 @@
 		goto out;
 	}
 
-	pfns = kcalloc(kdata.num, sizeof(*pfns), GFP_KERNEL);
+	pfns = kcalloc(kdata.num, sizeof(*pfns), GFP_KERNEL | __GFP_NOWARN);
 	if (!pfns) {
 		rc = -ENOMEM;
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/pvcalls-back.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/pvcalls-back.c
@@ -129,13 +129,13 @@
 	if (masked_prod < masked_cons) {
 		vec[0].iov_base = data->in + masked_prod;
 		vec[0].iov_len = wanted;
-		iov_iter_kvec(&msg.msg_iter, WRITE, vec, 1, wanted);
+		iov_iter_kvec(&msg.msg_iter, READ, vec, 1, wanted);
 	} else {
 		vec[0].iov_base = data->in + masked_prod;
 		vec[0].iov_len = array_size - masked_prod;
 		vec[1].iov_base = data->in;
 		vec[1].iov_len = wanted - vec[0].iov_len;
-		iov_iter_kvec(&msg.msg_iter, WRITE, vec, 2, wanted);
+		iov_iter_kvec(&msg.msg_iter, READ, vec, 2, wanted);
 	}
 
 	atomic_set(&map->read, 0);
@@ -188,13 +188,13 @@
 	if (pvcalls_mask(prod, array_size) > pvcalls_mask(cons, array_size)) {
 		vec[0].iov_base = data->out + pvcalls_mask(cons, array_size);
 		vec[0].iov_len = size;
-		iov_iter_kvec(&msg.msg_iter, READ, vec, 1, size);
+		iov_iter_kvec(&msg.msg_iter, WRITE, vec, 1, size);
 	} else {
 		vec[0].iov_base = data->out + pvcalls_mask(cons, array_size);
 		vec[0].iov_len = array_size - pvcalls_mask(cons, array_size);
 		vec[1].iov_base = data->out;
 		vec[1].iov_len = size - vec[0].iov_len;
-		iov_iter_kvec(&msg.msg_iter, READ, vec, 2, size);
+		iov_iter_kvec(&msg.msg_iter, WRITE, vec, 2, size);
 	}
 
 	atomic_set(&map->write, 0);
@@ -321,8 +321,10 @@
 	void *page;
 
 	map = kzalloc(sizeof(*map), GFP_KERNEL);
-	if (map == NULL)
+	if (map == NULL) {
+		sock_release(sock);
 		return NULL;
+	}
 
 	map->fedata = fedata;
 	map->sock = sock;
@@ -414,10 +416,8 @@
 					req->u.connect.ref,
 					req->u.connect.evtchn,
 					sock);
-	if (!map) {
+	if (!map)
 		ret = -EFAULT;
-		sock_release(sock);
-	}
 
 out:
 	rsp = RING_GET_RESPONSE(&fedata->ring, fedata->ring.rsp_prod_pvt++);
@@ -558,7 +558,6 @@
 					sock);
 	if (!map) {
 		ret = -EFAULT;
-		sock_release(sock);
 		goto out_error;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/pvcalls-front.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/pvcalls-front.c
@@ -337,8 +337,8 @@
 	if (!map->active.ring)
 		return;
 
-	free_pages((unsigned long)map->active.data.in,
-			map->active.ring->ring_order);
+	free_pages_exact(map->active.data.in,
+			 PAGE_SIZE << map->active.ring->ring_order);
 	free_page((unsigned long)map->active.ring);
 }
 
@@ -352,8 +352,8 @@
 		goto out;
 
 	map->active.ring->ring_order = PVCALLS_RING_ORDER;
-	bytes = (void *)__get_free_pages(GFP_KERNEL | __GFP_ZERO,
-					PVCALLS_RING_ORDER);
+	bytes = alloc_pages_exact(PAGE_SIZE << PVCALLS_RING_ORDER,
+				  GFP_KERNEL | __GFP_ZERO);
 	if (!bytes)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/pvcalls.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/pvcalls.c
@@ -0,0 +1,134 @@
+#include <linux/types.h>
+#include <linux/bitops.h>
+#include <linux/cred.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/kmod.h>
+#include <linux/list.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/net.h>
+#include <linux/poll.h>
+#include <linux/skbuff.h>
+#include <linux/smp.h>
+#include <linux/socket.h>
+#include <linux/stddef.h>
+#include <linux/unistd.h>
+#include <linux/wait.h>
+#include <linux/workqueue.h>
+#include <net/sock.h>
+#include <net/inet_common.h>
+
+#include "pvcalls-front.h"
+
+static int
+pvcalls_bind(struct socket *sock, struct sockaddr *addr, int addr_len)
+{
+	int ret;
+	ret = pvcalls_front_socket(sock);
+	if (ret < 0)
+		return ret;
+	return pvcalls_front_bind(sock, addr, addr_len);
+}
+
+static int pvcalls_stream_connect(struct socket *sock, struct sockaddr *addr,
+				int addr_len, int flags)
+{
+	int ret;
+	ret = pvcalls_front_socket(sock);
+	if (ret < 0)
+		return ret;
+	return pvcalls_front_connect(sock, addr, addr_len, flags);
+}
+
+static int pvcalls_accept(struct socket *sock, struct socket *newsock, int flags, bool kern)
+{
+	return pvcalls_front_accept(sock, newsock, flags);
+}
+
+static int pvcalls_getname(struct socket *sock,
+			 struct sockaddr *uaddr, int peer)
+{
+	DECLARE_SOCKADDR(struct sockaddr_in *, sin, uaddr);
+
+	sin->sin_family = AF_INET;
+	memset(sin->sin_zero, 0, sizeof(sin->sin_zero));
+	return 0;
+}
+
+static unsigned int pvcalls_poll(struct file *file, struct socket *sock,
+			       poll_table *wait)
+{
+	return pvcalls_front_poll(file, sock, wait);
+}
+
+static int pvcalls_listen(struct socket *sock, int backlog)
+{
+	return pvcalls_front_listen(sock, backlog);
+}
+
+static int pvcalls_stream_sendmsg(struct socket *sock, struct msghdr *msg,
+				size_t len)
+{
+	return pvcalls_front_sendmsg(sock, msg, len);
+}
+
+static int
+pvcalls_stream_recvmsg(struct socket *sock, struct msghdr *msg, size_t len,
+		     int flags)
+{
+	return pvcalls_front_recvmsg(sock, msg, len, flags);
+}
+
+static int pvcalls_release(struct socket *s)
+{
+	return pvcalls_front_release(s);
+}
+
+static int pvcalls_shutdown(struct socket *s, int h)
+{
+	return -ENOTSUPP;
+}
+
+static int sock_no_setsockopt(struct socket *sock, int level, int optname,
+			   sockptr_t optval, unsigned int optlen)
+{
+	return -ENOTSUPP;
+}
+
+static int sock_no_getsockopt(struct socket *sock, int level, int optname,
+			   char __user *optval, int __user *optlen)
+{
+	return -ENOTSUPP;
+}
+
+const struct proto_ops pvcalls_stream_ops = {
+	.family = PF_INET,
+	.owner = THIS_MODULE,
+	.release = pvcalls_release,
+	.bind = pvcalls_bind,
+	.connect = pvcalls_stream_connect,
+	.socketpair = sock_no_socketpair,
+	.accept = pvcalls_accept,
+	.getname = pvcalls_getname,
+	.poll = pvcalls_poll,
+	.ioctl = sock_no_ioctl,
+	.listen = pvcalls_listen,
+	.shutdown = pvcalls_shutdown,
+	.setsockopt = sock_no_setsockopt,
+	.getsockopt = sock_no_getsockopt,
+	.sendmsg = pvcalls_stream_sendmsg,
+	.recvmsg = pvcalls_stream_recvmsg,
+	.mmap = sock_no_mmap,
+	.sendpage = sock_no_sendpage,
+};
+
+bool pvcalls = false;
+static __init int xen_parse_pvcalls(char *arg)
+{
+       pvcalls = true;
+       return 0;
+}
+early_param("pvcalls", xen_parse_pvcalls);
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/swiotlb-xen.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/swiotlb-xen.c
@@ -79,9 +79,15 @@
 {
 	unsigned long next_bfn, xen_pfn = XEN_PFN_DOWN(p);
 	unsigned int i, nr_pages = XEN_PFN_UP(xen_offset_in_page(p) + size);
+	phys_addr_t algn = 1ULL << (get_order(size) + PAGE_SHIFT);
 
 	next_bfn = pfn_to_bfn(xen_pfn);
 
+	/* If buffer is physically aligned, ensure DMA alignment. */
+	if (IS_ALIGNED(p, algn) &&
+	    !IS_ALIGNED((phys_addr_t)next_bfn << XEN_PAGE_SHIFT, algn))
+		return 1;
+
 	for (i = 1; i < nr_pages; i++)
 		if (pfn_to_bfn(++xen_pfn) != ++next_bfn)
 			return 1;
@@ -380,7 +386,7 @@
 	 */
 	trace_swiotlb_bounced(dev, dev_addr, size, swiotlb_force);
 
-	map = swiotlb_tbl_map_single(dev, phys, size, size, dir, attrs);
+	map = swiotlb_tbl_map_single(dev, phys, size, size, 0, dir, attrs);
 	if (map == (phys_addr_t)DMA_MAPPING_ERROR)
 		return DMA_MAPPING_ERROR;
 
@@ -564,4 +570,5 @@
 	.get_sgtable = dma_common_get_sgtable,
 	.alloc_pages = dma_common_alloc_pages,
 	.free_pages = dma_common_free_pages,
+	.max_mapping_size = swiotlb_max_mapping_size,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xen-pciback/conf_space.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xen-pciback/conf_space.c
@@ -288,12 +288,6 @@
 	u16 val;
 	int ret = 0;
 
-	err = pci_read_config_word(dev, PCI_COMMAND, &val);
-	if (err)
-		return err;
-	if (!(val & PCI_COMMAND_INTX_DISABLE))
-		ret |= INTERRUPT_TYPE_INTX;
-
 	/*
 	 * Do not trust dev->msi(x)_enabled here, as enabling could be done
 	 * bypassing the pci_*msi* functions, by the qemu.
@@ -316,6 +310,19 @@
 		if (val & PCI_MSIX_FLAGS_ENABLE)
 			ret |= INTERRUPT_TYPE_MSIX;
 	}
+
+	/*
+	 * PCIe spec says device cannot use INTx if MSI/MSI-X is enabled,
+	 * so check for INTx only when both are disabled.
+	 */
+	if (!ret) {
+		err = pci_read_config_word(dev, PCI_COMMAND, &val);
+		if (err)
+			return err;
+		if (!(val & PCI_COMMAND_INTX_DISABLE))
+			ret |= INTERRUPT_TYPE_INTX;
+	}
+
 	return ret ?: INTERRUPT_TYPE_NONE;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xen-pciback/conf_space_capability.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xen-pciback/conf_space_capability.c
@@ -160,7 +160,7 @@
 	}
 
 out:
-	return ERR_PTR(err);
+	return err ? ERR_PTR(err) : NULL;
 }
 
 static const struct config_field caplist_pm[] = {
@@ -190,13 +190,16 @@
 };
 
 static struct msi_msix_field_config {
-	u16          enable_bit; /* bit for enabling MSI/MSI-X */
-	unsigned int int_type;   /* interrupt type for exclusiveness check */
+	u16          enable_bit;   /* bit for enabling MSI/MSI-X */
+	u16          allowed_bits; /* bits allowed to be changed */
+	unsigned int int_type;     /* interrupt type for exclusiveness check */
 } msi_field_config = {
 	.enable_bit	= PCI_MSI_FLAGS_ENABLE,
+	.allowed_bits	= PCI_MSI_FLAGS_ENABLE,
 	.int_type	= INTERRUPT_TYPE_MSI,
 }, msix_field_config = {
 	.enable_bit	= PCI_MSIX_FLAGS_ENABLE,
+	.allowed_bits	= PCI_MSIX_FLAGS_ENABLE | PCI_MSIX_FLAGS_MASKALL,
 	.int_type	= INTERRUPT_TYPE_MSIX,
 };
 
@@ -229,14 +232,20 @@
 		return 0;
 
 	if (!dev_data->allow_interrupt_control ||
-	    (new_value ^ old_value) & ~field_config->enable_bit)
+	    (new_value ^ old_value) & ~field_config->allowed_bits)
 		return PCIBIOS_SET_FAILED;
 
 	if (new_value & field_config->enable_bit) {
-		/* don't allow enabling together with other interrupt types */
+		/*
+		 * Don't allow enabling together with other interrupt type, but do
+		 * allow enabling MSI(-X) while INTx is still active to please Linuxes
+		 * MSI(-X) startup sequence. It is safe to do, as according to PCI
+		 * spec, device with enabled MSI(-X) shouldn't use INTx.
+		 */
 		int int_type = xen_pcibk_get_interrupt_type(dev);
 
 		if (int_type == INTERRUPT_TYPE_NONE ||
+		    int_type == INTERRUPT_TYPE_INTX ||
 		    int_type == field_config->int_type)
 			goto write;
 		return PCIBIOS_SET_FAILED;
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xen-pciback/conf_space_header.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xen-pciback/conf_space_header.c
@@ -104,24 +104,9 @@
 		pci_clear_mwi(dev);
 	}
 
-	if (dev_data && dev_data->allow_interrupt_control) {
-		if ((cmd->val ^ value) & PCI_COMMAND_INTX_DISABLE) {
-			if (value & PCI_COMMAND_INTX_DISABLE) {
-				pci_intx(dev, 0);
-			} else {
-				/* Do not allow enabling INTx together with MSI or MSI-X. */
-				switch (xen_pcibk_get_interrupt_type(dev)) {
-				case INTERRUPT_TYPE_NONE:
-					pci_intx(dev, 1);
-					break;
-				case INTERRUPT_TYPE_INTX:
-					break;
-				default:
-					return PCIBIOS_SET_FAILED;
-				}
-			}
-		}
-	}
+	if (dev_data && dev_data->allow_interrupt_control &&
+	    ((cmd->val ^ value) & PCI_COMMAND_INTX_DISABLE))
+		pci_intx(dev, !(value & PCI_COMMAND_INTX_DISABLE));
 
 	cmd->val = value;
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xenbus/xenbus_client.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xenbus/xenbus_client.c
@@ -379,7 +379,14 @@
 		      unsigned int nr_pages, grant_ref_t *grefs)
 {
 	int err;
-	int i, j;
+	unsigned int i;
+	grant_ref_t gref_head;
+
+	err = gnttab_alloc_grant_references(nr_pages, &gref_head);
+	if (err) {
+		xenbus_dev_fatal(dev, err, "granting access to ring page");
+		return err;
+	}
 
 	for (i = 0; i < nr_pages; i++) {
 		unsigned long gfn;
@@ -389,23 +396,14 @@
 		else
 			gfn = virt_to_gfn(vaddr);
 
-		err = gnttab_grant_foreign_access(dev->otherend_id, gfn, 0);
-		if (err < 0) {
-			xenbus_dev_fatal(dev, err,
-					 "granting access to ring page");
-			goto fail;
-		}
-		grefs[i] = err;
+		grefs[i] = gnttab_claim_grant_reference(&gref_head);
+		gnttab_grant_foreign_access_ref(grefs[i], dev->otherend_id,
+						gfn, 0);
 
 		vaddr = vaddr + XEN_PAGE_SIZE;
 	}
 
 	return 0;
-
-fail:
-	for (j = 0; j < i; j++)
-		gnttab_end_foreign_access_ref(grefs[j], 0);
-	return err;
 }
 EXPORT_SYMBOL_GPL(xenbus_grant_ring);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xenbus/xenbus_dev_frontend.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xenbus/xenbus_dev_frontend.c
@@ -128,7 +128,7 @@
 {
 	struct xenbus_file_priv *u = filp->private_data;
 	struct read_buffer *rb;
-	unsigned i;
+	ssize_t i;
 	int ret;
 
 	mutex_lock(&u->reply_mutex);
@@ -148,7 +148,7 @@
 	rb = list_entry(u->read_buffers.next, struct read_buffer, list);
 	i = 0;
 	while (i < len) {
-		unsigned sz = min((unsigned)len - i, rb->len - rb->cons);
+		size_t sz = min_t(size_t, len - i, rb->len - rb->cons);
 
 		ret = copy_to_user(ubuf + i, &rb->msg[rb->cons], sz);
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xenbus/xenbus_probe.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xenbus/xenbus_probe.c
@@ -65,6 +65,7 @@
 #include "xenbus.h"
 
 
+static int xs_init_irq;
 int xen_store_evtchn;
 EXPORT_SYMBOL_GPL(xen_store_evtchn);
 
@@ -308,7 +309,7 @@
 	if (err) {
 		dev_warn(&dev->dev, "watch_otherend on %s failed.\n",
 		       dev->nodename);
-		return err;
+		goto fail_remove;
 	}
 
 	dev->spurious_threshold = 1;
@@ -317,6 +318,12 @@
 			 dev->nodename);
 
 	return 0;
+fail_remove:
+	if (drv->remove) {
+		down(&dev->reclaim_sem);
+		drv->remove(dev);
+		up(&dev->reclaim_sem);
+	}
 fail_put:
 	module_put(drv->driver.owner);
 fail:
@@ -750,6 +757,17 @@
 {
 	xenstored_ready = 1;
 
+	if (!xen_store_interface) {
+		xen_store_interface = xen_remap(xen_store_gfn << XEN_PAGE_SHIFT,
+						XEN_PAGE_SIZE);
+		/*
+		 * Now it is safe to free the IRQ used for xenstore late
+		 * initialization. No need to unbind: it is about to be
+		 * bound again.
+		 */
+		free_irq(xs_init_irq, &xb_waitq);
+	}
+
 	/*
 	 * In the HVM case, xenbus_init() deferred its call to
 	 * xs_init() in case callbacks were not operational yet.
@@ -798,20 +816,22 @@
 {
 	/*
 	 * Probe XenBus here in the XS_PV case, and also XS_HVM unless we
-	 * need to wait for the platform PCI device to come up.
+	 * need to wait for the platform PCI device to come up or
+	 * xen_store_interface is not ready.
 	 */
 	if (xen_store_domain_type == XS_PV ||
 	    (xen_store_domain_type == XS_HVM &&
-	     !xs_hvm_defer_init_for_callback()))
+	     !xs_hvm_defer_init_for_callback() &&
+	     xen_store_interface != NULL))
 		xenbus_probe();
 
 	/*
-	 * For XS_LOCAL, spawn a thread which will wait for xenstored
-	 * or a xenstore-stubdom to be started, then probe. It will be
-	 * triggered when communication starts happening, by waiting
-	 * on xb_waitq.
+	 * For XS_LOCAL or when xen_store_interface is not ready, spawn a
+	 * thread which will wait for xenstored or a xenstore-stubdom to be
+	 * started, then probe.  It will be triggered when communication
+	 * starts happening, by waiting on xb_waitq.
 	 */
-	if (xen_store_domain_type == XS_LOCAL) {
+	if (xen_store_domain_type == XS_LOCAL || xen_store_interface == NULL) {
 		struct task_struct *probe_task;
 
 		probe_task = kthread_run(xenbus_probe_thread, NULL,
@@ -907,10 +927,24 @@
 	.notifier_call = xenbus_resume_cb,
 };
 
-static int __init xenbus_init(void)
+static irqreturn_t xenbus_late_init(int irq, void *unused)
 {
 	int err = 0;
 	uint64_t v = 0;
+
+	err = hvm_get_parameter(HVM_PARAM_STORE_PFN, &v);
+	if (err || !v || !~v)
+		return IRQ_HANDLED;
+	xen_store_gfn = (unsigned long)v;
+
+	wake_up(&xb_waitq);
+	return IRQ_HANDLED;
+}
+
+static int __init xenbus_init(void)
+{
+	int err;
+	uint64_t v = 0;
 	xen_store_domain_type = XS_UNKNOWN;
 
 	if (!xen_domain())
@@ -949,10 +983,47 @@
 		err = hvm_get_parameter(HVM_PARAM_STORE_PFN, &v);
 		if (err)
 			goto out_error;
-		xen_store_gfn = (unsigned long)v;
-		xen_store_interface =
-			xen_remap(xen_store_gfn << XEN_PAGE_SHIFT,
-				  XEN_PAGE_SIZE);
+		/*
+		 * Uninitialized hvm_params are zero and return no error.
+		 * Although it is theoretically possible to have
+		 * HVM_PARAM_STORE_PFN set to zero on purpose, in reality it is
+		 * not zero when valid. If zero, it means that Xenstore hasn't
+		 * been properly initialized. Instead of attempting to map a
+		 * wrong guest physical address return error.
+		 *
+		 * Also recognize all bits set as an invalid value.
+		 */
+		if (!v) {
+			err = -ENOENT;
+			goto out_error;
+		}
+		if (v == ~0ULL) {
+			err = bind_evtchn_to_irqhandler(xen_store_evtchn,
+							xenbus_late_init,
+							0, "xenstore_late_init",
+							&xb_waitq);
+			if (err < 0) {
+				pr_err("xenstore_late_init couldn't bind irq err=%d\n",
+				       err);
+				return err;
+			}
+
+			xs_init_irq = err;
+		} else {
+			/* Avoid truncation on 32-bit. */
+#if BITS_PER_LONG == 32
+			if (v > ULONG_MAX) {
+				pr_err("%s: cannot handle HVM_PARAM_STORE_PFN=%llx > ULONG_MAX\n",
+						__func__, v);
+				err = -EINVAL;
+				goto out_error;
+			}
+#endif
+			xen_store_gfn = (unsigned long)v;
+			xen_store_interface =
+				xen_remap(xen_store_gfn << XEN_PAGE_SHIFT,
+					  XEN_PAGE_SIZE);
+		}
 		break;
 	default:
 		pr_warn("Xenstore state unknown\n");
@@ -983,8 +1054,10 @@
 	 */
 	proc_create_mount_point("xen");
 #endif
+	return 0;
 
 out_error:
+	xen_store_domain_type = XS_UNKNOWN;
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/drivers/xen/xlate_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/drivers/xen/xlate_mmu.c
@@ -261,7 +261,6 @@
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xen_xlate_map_ballooned_pages);
 
 struct remap_pfn {
 	struct mm_struct *mm;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/acl.c
@@ -123,6 +123,7 @@
 	char *name;
 	size_t size;
 	void *buffer;
+
 	if (!acl)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/acl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/acl.h
@@ -15,14 +15,15 @@
 #define FS_9P_ACL_H
 
 #ifdef CONFIG_9P_FS_POSIX_ACL
-extern int v9fs_get_acl(struct inode *, struct p9_fid *);
-extern struct posix_acl *v9fs_iop_get_acl(struct inode *inode, int type, bool rcu);
-extern int v9fs_acl_chmod(struct inode *, struct p9_fid *);
-extern int v9fs_set_create_acl(struct inode *, struct p9_fid *,
-			       struct posix_acl *, struct posix_acl *);
-extern int v9fs_acl_mode(struct inode *dir, umode_t *modep,
-			 struct posix_acl **dpacl, struct posix_acl **pacl);
-extern void v9fs_put_acl(struct posix_acl *dacl, struct posix_acl *acl);
+int v9fs_get_acl(struct inode *inode, struct p9_fid *fid);
+struct posix_acl *v9fs_iop_get_acl(struct inode *inode, int type,
+				   bool rcu);
+int v9fs_acl_chmod(struct inode *inode, struct p9_fid *fid);
+int v9fs_set_create_acl(struct inode *inode, struct p9_fid *fid,
+			struct posix_acl *dacl, struct posix_acl *acl);
+int v9fs_acl_mode(struct inode *dir, umode_t *modep,
+		  struct posix_acl **dpacl, struct posix_acl **pacl);
+void v9fs_put_acl(struct posix_acl *dacl, struct posix_acl *acl);
 #else
 #define v9fs_iop_get_acl NULL
 static inline int v9fs_get_acl(struct inode *inode, struct p9_fid *fid)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/cache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/cache.c
@@ -19,8 +19,8 @@
 #define CACHETAG_LEN  11
 
 struct fscache_netfs v9fs_cache_netfs = {
-	.name 		= "9p",
-	.version 	= 0,
+	.name		= "9p",
+	.version	= 0,
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/fid.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/fid.c
@@ -96,12 +96,8 @@
 		 dentry, dentry, from_kuid(&init_user_ns, uid),
 		 any);
 	ret = NULL;
-
-	if (d_inode(dentry))
-		ret = v9fs_fid_find_inode(d_inode(dentry), uid);
-
 	/* we'll recheck under lock if there's anything to look in */
-	if (!ret && dentry->d_fsdata) {
+	if (dentry->d_fsdata) {
 		struct hlist_head *h = (struct hlist_head *)&dentry->d_fsdata;
 		spin_lock(&dentry->d_lock);
 		hlist_for_each_entry(fid, h, dlist) {
@@ -112,6 +108,9 @@
 			}
 		}
 		spin_unlock(&dentry->d_lock);
+	} else {
+		if (dentry->d_inode)
+			ret = v9fs_fid_find_inode(dentry->d_inode, uid);
 	}
 
 	return ret;
@@ -152,7 +151,7 @@
 	const unsigned char **wnames, *uname;
 	int i, n, l, clone, access;
 	struct v9fs_session_info *v9ses;
-	struct p9_fid *fid, *old_fid = NULL;
+	struct p9_fid *fid, *old_fid;
 
 	v9ses = v9fs_dentry2v9ses(dentry);
 	access = v9ses->flags & V9FS_ACCESS_MASK;
@@ -194,13 +193,12 @@
 		if (IS_ERR(fid))
 			return fid;
 
+		refcount_inc(&fid->count);
 		v9fs_fid_add(dentry->d_sb->s_root, fid);
 	}
 	/* If we are root ourself just return that */
-	if (dentry->d_sb->s_root == dentry) {
-		refcount_inc(&fid->count);
+	if (dentry->d_sb->s_root == dentry)
 		return fid;
-	}
 	/*
 	 * Do a multipath walk with attached root.
 	 * When walking parent we need to make sure we
@@ -212,6 +210,7 @@
 		fid = ERR_PTR(n);
 		goto err_out;
 	}
+	old_fid = fid;
 	clone = 1;
 	i = 0;
 	while (i < n) {
@@ -221,19 +220,15 @@
 		 * walk to ensure none of the patch component change
 		 */
 		fid = p9_client_walk(fid, l, &wnames[i], clone);
+		/* non-cloning walk will return the same fid */
+		if (fid != old_fid) {
+			p9_client_clunk(old_fid);
+			old_fid = fid;
+		}
 		if (IS_ERR(fid)) {
-			if (old_fid) {
-				/*
-				 * If we fail, clunk fid which are mapping
-				 * to path component and not the last component
-				 * of the path.
-				 */
-				p9_client_clunk(old_fid);
-			}
 			kfree(wnames);
 			goto err_out;
 		}
-		old_fid = fid;
 		i += l;
 		clone = 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/v9fs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/v9fs.c
@@ -190,8 +190,10 @@
 
 	while ((p = strsep(&options, ",")) != NULL) {
 		int token, r;
+
 		if (!*p)
 			continue;
+
 		token = match_token(p, tokens, args);
 		switch (token) {
 		case Opt_debug:
@@ -659,6 +661,7 @@
 static int v9fs_cache_register(void)
 {
 	int ret;
+
 	ret = v9fs_init_inode_cache();
 	if (ret < 0)
 		return ret;
@@ -686,6 +689,7 @@
 static int __init init_v9fs(void)
 {
 	int err;
+
 	pr_info("Installing v9fs 9p2000 file system support\n");
 	/* TODO: Setup list of registered trasnport modules */
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/v9fs_vfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/v9fs_vfs.h
@@ -44,9 +44,10 @@
 
 struct inode *v9fs_alloc_inode(struct super_block *sb);
 void v9fs_free_inode(struct inode *inode);
-struct inode *v9fs_get_inode(struct super_block *sb, umode_t mode, dev_t);
+struct inode *v9fs_get_inode(struct super_block *sb, umode_t mode,
+			     dev_t rdev);
 int v9fs_init_inode(struct v9fs_session_info *v9ses,
-		    struct inode *inode, umode_t mode, dev_t);
+		    struct inode *inode, umode_t mode, dev_t rdev);
 void v9fs_evict_inode(struct inode *inode);
 ino_t v9fs_qid2ino(struct p9_qid *qid);
 void v9fs_stat2inode(struct p9_wstat *stat, struct inode *inode,
@@ -59,8 +60,8 @@
 int v9fs_uflags2omode(int uflags, int extended);
 
 void v9fs_blank_wstat(struct p9_wstat *wstat);
-int v9fs_vfs_setattr_dotl(struct user_namespace *, struct dentry *,
-			  struct iattr *);
+int v9fs_vfs_setattr_dotl(struct user_namespace *mnt_userns,
+			  struct dentry *dentry, struct iattr *iattr);
 int v9fs_file_fsync_dotl(struct file *filp, loff_t start, loff_t end,
 			 int datasync);
 int v9fs_refresh_inode(struct p9_fid *fid, struct inode *inode);
@@ -68,9 +69,9 @@
 static inline void v9fs_invalidate_inode_attr(struct inode *inode)
 {
 	struct v9fs_inode *v9inode;
+
 	v9inode = V9FS_I(inode);
 	v9inode->cache_validity |= V9FS_INO_INVALID_ATTR;
-	return;
 }
 
 int v9fs_open_to_dotl_flags(int flags);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/vfs_addr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/vfs_addr.c
@@ -242,11 +242,13 @@
 	loff_t pos = iocb->ki_pos;
 	ssize_t n;
 	int err = 0;
+
 	if (iov_iter_rw(iter) == WRITE) {
 		n = p9_client_write(file->private_data, pos, iter, &err);
 		if (n) {
 			struct inode *inode = file_inode(file);
 			loff_t i_size = i_size_read(inode);
+
 			if (pos + n > i_size)
 				inode_add_bytes(inode, pos + n - i_size);
 		}
@@ -257,7 +259,7 @@
 }
 
 static int v9fs_write_begin(struct file *filp, struct address_space *mapping,
-			    loff_t pos, unsigned len, unsigned flags,
+			    loff_t pos, unsigned int len, unsigned int flags,
 			    struct page **pagep, void **fsdata)
 {
 	int retval = 0;
@@ -293,7 +295,7 @@
 }
 
 static int v9fs_write_end(struct file *filp, struct address_space *mapping,
-			  loff_t pos, unsigned len, unsigned copied,
+			  loff_t pos, unsigned int len, unsigned int copied,
 			  struct page *page, void *fsdata)
 {
 	loff_t last_pos = pos + copied;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/vfs_dentry.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/vfs_dentry.c
@@ -52,11 +52,17 @@
 static void v9fs_dentry_release(struct dentry *dentry)
 {
 	struct hlist_node *p, *n;
+	struct hlist_head head;
+
 	p9_debug(P9_DEBUG_VFS, " dentry: %pd (%p)\n",
 		 dentry, dentry);
-	hlist_for_each_safe(p, n, (struct hlist_head *)&dentry->d_fsdata)
+
+	spin_lock(&dentry->d_lock);
+	hlist_move_list((struct hlist_head *)&dentry->d_fsdata, &head);
+	spin_unlock(&dentry->d_lock);
+
+	hlist_for_each_safe(p, n, &head)
 		p9_client_clunk(hlist_entry(p, struct p9_fid, dlist));
-	dentry->d_fsdata = NULL;
 }
 
 static int v9fs_lookup_revalidate(struct dentry *dentry, unsigned int flags)
@@ -76,6 +82,7 @@
 	if (v9inode->cache_validity & V9FS_INO_INVALID_ATTR) {
 		int retval;
 		struct v9fs_session_info *v9ses;
+
 		fid = v9fs_fid_lookup(dentry);
 		if (IS_ERR(fid))
 			return PTR_ERR(fid);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/vfs_file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/vfs_file.c
@@ -408,6 +408,7 @@
 		struct inode *inode = file_inode(file);
 		loff_t i_size;
 		unsigned long pg_start, pg_end;
+
 		pg_start = origin >> PAGE_SHIFT;
 		pg_end = (origin + retval - 1) >> PAGE_SHIFT;
 		if (inode->i_mapping && inode->i_mapping->nrpages)
@@ -659,6 +660,7 @@
 	.splice_read = generic_file_splice_read,
 	.splice_write = iter_file_splice_write,
 	.fsync = v9fs_file_fsync,
+	.setlease = simple_nosetlease,
 };
 
 const struct file_operations v9fs_file_operations_dotl = {
@@ -700,4 +702,5 @@
 	.splice_read = generic_file_splice_read,
 	.splice_write = iter_file_splice_write,
 	.fsync = v9fs_file_fsync_dotl,
+	.setlease = simple_nosetlease,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/vfs_inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/vfs_inode.c
@@ -49,6 +49,7 @@
 static u32 unixmode2p9mode(struct v9fs_session_info *v9ses, umode_t mode)
 {
 	int res;
+
 	res = mode & 0777;
 	if (S_ISDIR(mode))
 		res |= P9_DMDIR;
@@ -86,7 +87,7 @@
 	int res;
 	int mode = stat->mode;
 
-	res = mode & S_IALLUGO;
+	res = mode & 0777; /* S_IRWXUGO */
 	if (v9fs_proto_dotu(v9ses)) {
 		if ((mode & P9_DMSETUID) == P9_DMSETUID)
 			res |= S_ISUID;
@@ -177,6 +178,9 @@
 		break;
 	}
 
+	if (uflags & O_TRUNC)
+		ret |= P9_OTRUNC;
+
 	if (extended) {
 		if (uflags & O_EXCL)
 			ret |= P9_OEXCL;
@@ -223,6 +227,7 @@
 struct inode *v9fs_alloc_inode(struct super_block *sb)
 {
 	struct v9fs_inode *v9inode;
+
 	v9inode = kmem_cache_alloc(v9fs_inode_cache, GFP_KERNEL);
 	if (!v9inode)
 		return NULL;
@@ -251,7 +256,7 @@
 {
 	int err = 0;
 
-	inode_init_owner(&init_user_ns,inode,  NULL, mode);
+	inode_init_owner(&init_user_ns, inode, NULL, mode);
 	inode->i_blocks = 0;
 	inode->i_rdev = rdev;
 	inode->i_atime = inode->i_mtime = inode->i_ctime = current_time(inode);
@@ -440,7 +445,7 @@
 	unsigned long i_ino;
 	struct inode *inode;
 	struct v9fs_session_info *v9ses = sb->s_fs_info;
-	int (*test)(struct inode *, void *);
+	int (*test)(struct inode *inode, void *data);
 
 	if (new)
 		test = v9fs_test_new_inode;
@@ -499,8 +504,10 @@
 static int v9fs_at_to_dotl_flags(int flags)
 {
 	int rflags = 0;
+
 	if (flags & AT_REMOVEDIR)
 		rflags |= P9_DOTL_AT_REMOVEDIR;
+
 	return rflags;
 }
 
@@ -797,7 +804,7 @@
 
 static int
 v9fs_vfs_atomic_open(struct inode *dir, struct dentry *dentry,
-		     struct file *file, unsigned flags, umode_t mode)
+		     struct file *file, unsigned int flags, umode_t mode)
 {
 	int err;
 	u32 perm;
@@ -1084,7 +1091,7 @@
 		fid = v9fs_fid_lookup(dentry);
 		use_dentry = 1;
 	}
-	if(IS_ERR(fid))
+	if (IS_ERR(fid))
 		return PTR_ERR(fid);
 
 	v9fs_blank_wstat(&wstat);
@@ -1228,15 +1235,15 @@
 		return ERR_PTR(-ECHILD);
 
 	v9ses = v9fs_dentry2v9ses(dentry);
-	fid = v9fs_fid_lookup(dentry);
+	if (!v9fs_proto_dotu(v9ses))
+		return ERR_PTR(-EBADF);
+
 	p9_debug(P9_DEBUG_VFS, "%pd\n", dentry);
+	fid = v9fs_fid_lookup(dentry);
 
 	if (IS_ERR(fid))
 		return ERR_CAST(fid);
 
-	if (!v9fs_proto_dotu(v9ses))
-		return ERR_PTR(-EBADF);
-
 	st = p9_client_stat(fid);
 	p9_client_clunk(fid);
 	if (IS_ERR(st))
@@ -1364,7 +1371,7 @@
 	char name[2 + U32_MAX_DIGITS + 1 + U32_MAX_DIGITS + 1];
 	u32 perm;
 
-	p9_debug(P9_DEBUG_VFS, " %lu,%pd mode: %hx MAJOR: %u MINOR: %u\n",
+	p9_debug(P9_DEBUG_VFS, " %lu,%pd mode: %x MAJOR: %u MINOR: %u\n",
 		 dir->i_ino, dentry, mode,
 		 MAJOR(rdev), MINOR(rdev));
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/vfs_inode_dotl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/vfs_inode_dotl.c
@@ -107,7 +107,7 @@
 	unsigned long i_ino;
 	struct inode *inode;
 	struct v9fs_session_info *v9ses = sb->s_fs_info;
-	int (*test)(struct inode *, void *);
+	int (*test)(struct inode *inode, void *data);
 
 	if (new)
 		test = v9fs_test_new_inode_dotl;
@@ -230,7 +230,7 @@
 
 static int
 v9fs_vfs_atomic_open_dotl(struct inode *dir, struct dentry *dentry,
-			  struct file *file, unsigned flags, umode_t omode)
+			  struct file *file, unsigned int flags, umode_t omode)
 {
 	int err = 0;
 	kgid_t gid;
@@ -261,7 +261,7 @@
 	v9ses = v9fs_inode2v9ses(dir);
 
 	name = dentry->d_name.name;
-	p9_debug(P9_DEBUG_VFS, "name:%s flags:0x%x mode:0x%hx\n",
+	p9_debug(P9_DEBUG_VFS, "name:%s flags:0x%x mode:0x%x\n",
 		 name, flags, omode);
 
 	dfid = v9fs_parent_fid(dentry);
@@ -276,6 +276,7 @@
 	if (IS_ERR(ofid)) {
 		err = PTR_ERR(ofid);
 		p9_debug(P9_DEBUG_VFS, "p9_client_walk failed %d\n", err);
+		p9_client_clunk(dfid);
 		goto out;
 	}
 
@@ -287,6 +288,7 @@
 	if (err) {
 		p9_debug(P9_DEBUG_VFS, "Failed to get acl values in creat %d\n",
 			 err);
+		p9_client_clunk(dfid);
 		goto error;
 	}
 	err = p9_client_create_dotl(ofid, name, v9fs_open_to_dotl_flags(flags),
@@ -294,6 +296,7 @@
 	if (err < 0) {
 		p9_debug(P9_DEBUG_VFS, "p9_client_open_dotl failed in creat %d\n",
 			 err);
+		p9_client_clunk(dfid);
 		goto error;
 	}
 	v9fs_invalidate_inode_attr(dir);
@@ -553,7 +556,10 @@
 {
 	int retval, use_dentry = 0;
 	struct p9_fid *fid = NULL;
-	struct p9_iattr_dotl p9attr;
+	struct p9_iattr_dotl p9attr = {
+		.uid = INVALID_UID,
+		.gid = INVALID_GID,
+	};
 	struct inode *inode = d_inode(dentry);
 
 	p9_debug(P9_DEBUG_VFS, "\n");
@@ -563,14 +569,22 @@
 		return retval;
 
 	p9attr.valid = v9fs_mapped_iattr_valid(iattr->ia_valid);
-	p9attr.mode = iattr->ia_mode;
-	p9attr.uid = iattr->ia_uid;
-	p9attr.gid = iattr->ia_gid;
-	p9attr.size = iattr->ia_size;
-	p9attr.atime_sec = iattr->ia_atime.tv_sec;
-	p9attr.atime_nsec = iattr->ia_atime.tv_nsec;
-	p9attr.mtime_sec = iattr->ia_mtime.tv_sec;
-	p9attr.mtime_nsec = iattr->ia_mtime.tv_nsec;
+	if (iattr->ia_valid & ATTR_MODE)
+		p9attr.mode = iattr->ia_mode;
+	if (iattr->ia_valid & ATTR_UID)
+		p9attr.uid = iattr->ia_uid;
+	if (iattr->ia_valid & ATTR_GID)
+		p9attr.gid = iattr->ia_gid;
+	if (iattr->ia_valid & ATTR_SIZE)
+		p9attr.size = iattr->ia_size;
+	if (iattr->ia_valid & ATTR_ATIME_SET) {
+		p9attr.atime_sec = iattr->ia_atime.tv_sec;
+		p9attr.atime_nsec = iattr->ia_atime.tv_nsec;
+	}
+	if (iattr->ia_valid & ATTR_MTIME_SET) {
+		p9attr.mtime_sec = iattr->ia_mtime.tv_sec;
+		p9attr.mtime_nsec = iattr->ia_mtime.tv_nsec;
+	}
 
 	if (iattr->ia_valid & ATTR_FILE) {
 		fid = iattr->ia_file->private_data;
@@ -807,6 +821,7 @@
 	if (v9ses->cache == CACHE_LOOSE || v9ses->cache == CACHE_FSCACHE) {
 		/* Get the latest stat info from server. */
 		struct p9_fid *fid;
+
 		fid = v9fs_fid_lookup(old_dentry);
 		if (IS_ERR(fid))
 			return PTR_ERR(fid);
@@ -843,7 +858,7 @@
 	struct p9_qid qid;
 	struct posix_acl *dacl = NULL, *pacl = NULL;
 
-	p9_debug(P9_DEBUG_VFS, " %lu,%pd mode: %hx MAJOR: %u MINOR: %u\n",
+	p9_debug(P9_DEBUG_VFS, " %lu,%pd mode: %x MAJOR: %u MINOR: %u\n",
 		 dir->i_ino, dentry, omode,
 		 MAJOR(rdev), MINOR(rdev));
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/vfs_super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/vfs_super.c
@@ -113,7 +113,7 @@
 	struct inode *inode = NULL;
 	struct dentry *root = NULL;
 	struct v9fs_session_info *v9ses = NULL;
-	umode_t mode = S_IRWXUGO | S_ISVTX;
+	umode_t mode = 0777 | S_ISVTX;
 	struct p9_fid *fid;
 	int retval = 0;
 
@@ -157,6 +157,7 @@
 	sb->s_root = root;
 	if (v9fs_proto_dotl(v9ses)) {
 		struct p9_stat_dotl *st = NULL;
+
 		st = p9_client_getattr_dotl(fid, P9_STATS_BASIC);
 		if (IS_ERR(st)) {
 			retval = PTR_ERR(st);
@@ -167,6 +168,7 @@
 		kfree(st);
 	} else {
 		struct p9_wstat *st = NULL;
+
 		st = p9_client_stat(fid);
 		if (IS_ERR(st)) {
 			retval = PTR_ERR(st);
@@ -275,12 +277,13 @@
 static int v9fs_drop_inode(struct inode *inode)
 {
 	struct v9fs_session_info *v9ses;
+
 	v9ses = v9fs_inode2v9ses(inode);
 	if (v9ses->cache == CACHE_LOOSE || v9ses->cache == CACHE_FSCACHE)
 		return generic_drop_inode(inode);
 	/*
 	 * in case of non cached mode always drop the
-	 * the inode because we want the inode attribute
+	 * inode because we want the inode attribute
 	 * to always match that on the server.
 	 */
 	return 1;
@@ -337,6 +340,7 @@
 	.alloc_inode = v9fs_alloc_inode,
 	.free_inode = v9fs_free_inode,
 	.statfs = simple_statfs,
+	.drop_inode = v9fs_drop_inode,
 	.evict_inode = v9fs_evict_inode,
 	.show_options = v9fs_show_options,
 	.umount_begin = v9fs_umount_begin,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/xattr.c
@@ -73,7 +73,7 @@
 	struct p9_fid *fid;
 	int ret;
 
-	p9_debug(P9_DEBUG_VFS, "name = %s value_len = %zu\n",
+	p9_debug(P9_DEBUG_VFS, "name = '%s' value_len = %zu\n",
 		 name, buffer_size);
 	fid = v9fs_fid_lookup(dentry);
 	if (IS_ERR(fid))
@@ -144,7 +144,8 @@
 
 ssize_t v9fs_listxattr(struct dentry *dentry, char *buffer, size_t buffer_size)
 {
-	return v9fs_xattr_get(dentry, NULL, buffer, buffer_size);
+	/* Txattrwalk with an empty string lists xattrs instead */
+	return v9fs_xattr_get(dentry, "", buffer, buffer_size);
 }
 
 static int v9fs_xattr_handler_get(const struct xattr_handler *handler,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/9p/xattr.h
+++ linux-xilinx-zynqmp-5.15.0/fs/9p/xattr.h
@@ -22,13 +22,14 @@
 extern const struct xattr_handler v9fs_xattr_acl_access_handler;
 extern const struct xattr_handler v9fs_xattr_acl_default_handler;
 
-extern ssize_t v9fs_fid_xattr_get(struct p9_fid *, const char *,
-				  void *, size_t);
-extern ssize_t v9fs_xattr_get(struct dentry *, const char *,
-			      void *, size_t);
-extern int v9fs_fid_xattr_set(struct p9_fid *, const char *,
-			  const void *, size_t, int);
-extern int v9fs_xattr_set(struct dentry *, const char *,
-			  const void *, size_t, int);
-extern ssize_t v9fs_listxattr(struct dentry *, char *, size_t);
+ssize_t v9fs_fid_xattr_get(struct p9_fid *fid, const char *name,
+			   void *buffer, size_t buffer_size);
+ssize_t v9fs_xattr_get(struct dentry *dentry, const char *name,
+		       void *buffer, size_t buffer_size);
+int v9fs_fid_xattr_set(struct p9_fid *fid, const char *name,
+		       const void *value, size_t value_len, int flags);
+int v9fs_xattr_set(struct dentry *dentry, const char *name,
+		   const void *value, size_t value_len, int flags);
+ssize_t v9fs_listxattr(struct dentry *dentry, char *buffer,
+		       size_t buffer_size);
 #endif /* FS_9P_XATTR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/fs/Kconfig
@@ -128,6 +128,24 @@
 source "fs/fuse/Kconfig"
 source "fs/overlayfs/Kconfig"
 
+config SHIFT_FS
+	tristate "UID/GID shifting overlay filesystem for containers"
+	help
+	  This filesystem can overlay any mounted filesystem and shift
+	  the uid/gid the files appear at.  The idea is that
+	  unprivileged containers can use this to mount root volumes
+	  using this technique.
+
+config SHIFT_FS_POSIX_ACL
+	bool "shiftfs POSIX Access Control Lists"
+	depends on SHIFT_FS
+	select FS_POSIX_ACL
+	help
+	  POSIX Access Control Lists (ACLs) support permissions for users and
+	  groups beyond the owner/group/world scheme.
+
+	  If you don't know what Access Control Lists are, say N.
+
 menu "Caches"
 
 source "fs/netfs/Kconfig"
@@ -312,6 +330,7 @@
 source "fs/ufs/Kconfig"
 source "fs/erofs/Kconfig"
 source "fs/vboxsf/Kconfig"
+source "fs/aufs/Kconfig"
 
 endif # MISC_FILESYSTEMS
 
@@ -344,7 +363,7 @@
 
 config LOCKD_V4
 	bool
-	depends on NFSD_V3 || NFS_V3
+	depends on NFSD || NFS_V3
 	depends on FILE_LOCKING
 	default y
 
@@ -369,8 +388,8 @@
 
 config SMBFS_COMMON
 	tristate
-	default y if CIFS=y
-	default m if CIFS=m
+	default y if CIFS=y || SMB_SERVER=y
+	default m if CIFS=m || SMB_SERVER=m
 
 source "fs/coda/Kconfig"
 source "fs/afs/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/fs/Makefile
+++ linux-xilinx-zynqmp-5.15.0/fs/Makefile
@@ -32,8 +32,6 @@
 obj-$(CONFIG_EVENTFD)		+= eventfd.o
 obj-$(CONFIG_USERFAULTFD)	+= userfaultfd.o
 obj-$(CONFIG_AIO)               += aio.o
-obj-$(CONFIG_IO_URING)		+= io_uring.o
-obj-$(CONFIG_IO_WQ)		+= io-wq.o
 obj-$(CONFIG_FS_DAX)		+= dax.o
 obj-$(CONFIG_FS_ENCRYPTION)	+= crypto/
 obj-$(CONFIG_FS_VERITY)		+= verity/
@@ -138,3 +136,5 @@
 obj-$(CONFIG_EROFS_FS)		+= erofs/
 obj-$(CONFIG_VBOXSF_FS)		+= vboxsf/
 obj-$(CONFIG_ZONEFS_FS)		+= zonefs/
+obj-$(CONFIG_AUFS_FS)           += aufs/
+obj-$(CONFIG_SHIFT_FS)		+= shiftfs.o
--- linux-xilinx-zynqmp-5.15.0.orig/fs/affs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/affs/file.c
@@ -598,7 +598,7 @@
 		BUG_ON(tmp > bsize);
 		AFFS_DATA_HEAD(bh)->ptype = cpu_to_be32(T_DATA);
 		AFFS_DATA_HEAD(bh)->key = cpu_to_be32(inode->i_ino);
-		AFFS_DATA_HEAD(bh)->sequence = cpu_to_be32(bidx);
+		AFFS_DATA_HEAD(bh)->sequence = cpu_to_be32(bidx + 1);
 		AFFS_DATA_HEAD(bh)->size = cpu_to_be32(tmp);
 		affs_fix_checksum(sb, bh);
 		bh->b_state &= ~(1UL << BH_New);
@@ -726,7 +726,8 @@
 		tmp = min(bsize - boff, to - from);
 		BUG_ON(boff + tmp > bsize || tmp > bsize);
 		memcpy(AFFS_DATA(bh) + boff, data + from, tmp);
-		be32_add_cpu(&AFFS_DATA_HEAD(bh)->size, tmp);
+		AFFS_DATA_HEAD(bh)->size = cpu_to_be32(
+			max(boff + tmp, be32_to_cpu(AFFS_DATA_HEAD(bh)->size)));
 		affs_fix_checksum(sb, bh);
 		mark_buffer_dirty_inode(bh, inode);
 		written += tmp;
@@ -748,7 +749,7 @@
 		if (buffer_new(bh)) {
 			AFFS_DATA_HEAD(bh)->ptype = cpu_to_be32(T_DATA);
 			AFFS_DATA_HEAD(bh)->key = cpu_to_be32(inode->i_ino);
-			AFFS_DATA_HEAD(bh)->sequence = cpu_to_be32(bidx);
+			AFFS_DATA_HEAD(bh)->sequence = cpu_to_be32(bidx + 1);
 			AFFS_DATA_HEAD(bh)->size = cpu_to_be32(bsize);
 			AFFS_DATA_HEAD(bh)->next = 0;
 			bh->b_state &= ~(1UL << BH_New);
@@ -782,7 +783,7 @@
 		if (buffer_new(bh)) {
 			AFFS_DATA_HEAD(bh)->ptype = cpu_to_be32(T_DATA);
 			AFFS_DATA_HEAD(bh)->key = cpu_to_be32(inode->i_ino);
-			AFFS_DATA_HEAD(bh)->sequence = cpu_to_be32(bidx);
+			AFFS_DATA_HEAD(bh)->sequence = cpu_to_be32(bidx + 1);
 			AFFS_DATA_HEAD(bh)->size = cpu_to_be32(tmp);
 			AFFS_DATA_HEAD(bh)->next = 0;
 			bh->b_state &= ~(1UL << BH_New);
@@ -881,7 +882,7 @@
 	if (inode->i_size > AFFS_I(inode)->mmu_private) {
 		struct address_space *mapping = inode->i_mapping;
 		struct page *page;
-		void *fsdata;
+		void *fsdata = NULL;
 		loff_t isize = inode->i_size;
 		int res;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/afs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/afs.h
@@ -10,7 +10,7 @@
 
 #include <linux/in.h>
 
-#define AFS_MAXCELLNAME		256  	/* Maximum length of a cell name */
+#define AFS_MAXCELLNAME		253  	/* Maximum length of a cell name (DNS limited) */
 #define AFS_MAXVOLNAME		64  	/* Maximum length of a volume name */
 #define AFS_MAXNSERVERS		8   	/* Maximum servers in a basic volume record */
 #define AFS_NMAXNSERVERS	13  	/* Maximum servers in a N/U-class volume record */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/afs_vl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/afs_vl.h
@@ -13,6 +13,7 @@
 #define AFS_VL_PORT		7003	/* volume location service port */
 #define VL_SERVICE		52	/* RxRPC service ID for the Volume Location service */
 #define YFS_VL_SERVICE		2503	/* Service ID for AuriStor upgraded VL service */
+#define YFS_VL_MAXCELLNAME	256  	/* Maximum length of a cell name in YFS protocol */
 
 enum AFSVL_Operations {
 	VLGETENTRYBYID		= 503,	/* AFS Get VLDB entry by ID */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/callback.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/callback.c
@@ -110,13 +110,14 @@
 {
 	struct afs_volume *volume = NULL;
 	struct rb_node *p;
-	int seq = 0;
+	int seq = 1;
 
 	do {
 		/* Unfortunately, rbtree walking doesn't give reliable results
 		 * under just the RCU read lock, so we have to check for
 		 * changes.
 		 */
+		seq++; /* 2 on the 1st/lockless path, otherwise odd */
 		read_seqbegin_or_lock(&cell->volume_lock, &seq);
 
 		p = rcu_dereference_raw(cell->volumes.rb_node);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/cell.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/cell.c
@@ -158,9 +158,10 @@
 		cell->name[i] = tolower(name[i]);
 	cell->name[i] = 0;
 
-	atomic_set(&cell->ref, 1);
+	refcount_set(&cell->ref, 1);
 	atomic_set(&cell->active, 0);
 	INIT_WORK(&cell->manager, afs_manage_cell_work);
+	spin_lock_init(&cell->vs_lock);
 	cell->volumes = RB_ROOT;
 	INIT_HLIST_HEAD(&cell->proc_volumes);
 	seqlock_init(&cell->volume_lock);
@@ -287,7 +288,7 @@
 	cell = candidate;
 	candidate = NULL;
 	atomic_set(&cell->active, 2);
-	trace_afs_cell(cell->debug_id, atomic_read(&cell->ref), 2, afs_cell_trace_insert);
+	trace_afs_cell(cell->debug_id, refcount_read(&cell->ref), 2, afs_cell_trace_insert);
 	rb_link_node_rcu(&cell->net_node, parent, pp);
 	rb_insert_color(&cell->net_node, &net->cells);
 	up_write(&net->cells_lock);
@@ -295,7 +296,7 @@
 	afs_queue_cell(cell, afs_cell_trace_get_queue_new);
 
 wait_for_cell:
-	trace_afs_cell(cell->debug_id, atomic_read(&cell->ref), atomic_read(&cell->active),
+	trace_afs_cell(cell->debug_id, refcount_read(&cell->ref), atomic_read(&cell->active),
 		       afs_cell_trace_wait);
 	_debug("wait_for_cell");
 	wait_var_event(&cell->state,
@@ -409,10 +410,12 @@
 		if (ret == -ENOMEM)
 			goto out_wake;
 
-		ret = -ENOMEM;
 		vllist = afs_alloc_vlserver_list(0);
-		if (!vllist)
+		if (!vllist) {
+			if (ret >= 0)
+				ret = -ENOMEM;
 			goto out_wake;
+		}
 
 		switch (ret) {
 		case -ENODATA:
@@ -490,13 +493,13 @@
 {
 	struct afs_cell *cell = container_of(rcu, struct afs_cell, rcu);
 	struct afs_net *net = cell->net;
-	int u;
+	int r;
 
 	_enter("%p{%s}", cell, cell->name);
 
-	u = atomic_read(&cell->ref);
-	ASSERTCMP(u, ==, 0);
-	trace_afs_cell(cell->debug_id, u, atomic_read(&cell->active), afs_cell_trace_free);
+	r = refcount_read(&cell->ref);
+	ASSERTCMP(r, ==, 0);
+	trace_afs_cell(cell->debug_id, r, atomic_read(&cell->active), afs_cell_trace_free);
 
 	afs_put_vlserverlist(net, rcu_access_pointer(cell->vl_servers));
 	afs_unuse_cell(net, cell->alias_of, afs_cell_trace_unuse_alias);
@@ -539,13 +542,10 @@
  */
 struct afs_cell *afs_get_cell(struct afs_cell *cell, enum afs_cell_trace reason)
 {
-	int u;
+	int r;
 
-	if (atomic_read(&cell->ref) <= 0)
-		BUG();
-
-	u = atomic_inc_return(&cell->ref);
-	trace_afs_cell(cell->debug_id, u, atomic_read(&cell->active), reason);
+	__refcount_inc(&cell->ref, &r);
+	trace_afs_cell(cell->debug_id, r + 1, atomic_read(&cell->active), reason);
 	return cell;
 }
 
@@ -556,12 +556,14 @@
 {
 	if (cell) {
 		unsigned int debug_id = cell->debug_id;
-		unsigned int u, a;
+		unsigned int a;
+		bool zero;
+		int r;
 
 		a = atomic_read(&cell->active);
-		u = atomic_dec_return(&cell->ref);
-		trace_afs_cell(debug_id, u, a, reason);
-		if (u == 0) {
+		zero = __refcount_dec_and_test(&cell->ref, &r);
+		trace_afs_cell(debug_id, r - 1, a, reason);
+		if (zero) {
 			a = atomic_read(&cell->active);
 			WARN(a != 0, "Cell active count %u > 0\n", a);
 			call_rcu(&cell->rcu, afs_cell_destroy);
@@ -574,14 +576,12 @@
  */
 struct afs_cell *afs_use_cell(struct afs_cell *cell, enum afs_cell_trace reason)
 {
-	int u, a;
-
-	if (atomic_read(&cell->ref) <= 0)
-		BUG();
+	int r, a;
 
-	u = atomic_read(&cell->ref);
+	r = refcount_read(&cell->ref);
+	WARN_ON(r == 0);
 	a = atomic_inc_return(&cell->active);
-	trace_afs_cell(cell->debug_id, u, a, reason);
+	trace_afs_cell(cell->debug_id, r, a, reason);
 	return cell;
 }
 
@@ -593,7 +593,7 @@
 {
 	unsigned int debug_id;
 	time64_t now, expire_delay;
-	int u, a;
+	int r, a;
 
 	if (!cell)
 		return;
@@ -607,9 +607,9 @@
 		expire_delay = afs_cell_gc_delay;
 
 	debug_id = cell->debug_id;
-	u = atomic_read(&cell->ref);
+	r = refcount_read(&cell->ref);
 	a = atomic_dec_return(&cell->active);
-	trace_afs_cell(debug_id, u, a, reason);
+	trace_afs_cell(debug_id, r, a, reason);
 	WARN_ON(a == 0);
 	if (a == 1)
 		/* 'cell' may now be garbage collected. */
@@ -621,11 +621,11 @@
  */
 void afs_see_cell(struct afs_cell *cell, enum afs_cell_trace reason)
 {
-	int u, a;
+	int r, a;
 
-	u = atomic_read(&cell->ref);
+	r = refcount_read(&cell->ref);
 	a = atomic_read(&cell->active);
-	trace_afs_cell(cell->debug_id, u, a, reason);
+	trace_afs_cell(cell->debug_id, r, a, reason);
 }
 
 /*
@@ -751,7 +751,7 @@
 		active = 1;
 		if (atomic_try_cmpxchg_relaxed(&cell->active, &active, 0)) {
 			rb_erase(&cell->net_node, &net->cells);
-			trace_afs_cell(cell->debug_id, atomic_read(&cell->ref), 0,
+			trace_afs_cell(cell->debug_id, refcount_read(&cell->ref), 0,
 				       afs_cell_trace_unuse_delete);
 			smp_store_release(&cell->state, AFS_CELL_REMOVED);
 		}
@@ -878,7 +878,7 @@
 		bool sched_cell = false;
 
 		active = atomic_read(&cell->active);
-		trace_afs_cell(cell->debug_id, atomic_read(&cell->ref),
+		trace_afs_cell(cell->debug_id, refcount_read(&cell->ref),
 			       active, afs_cell_trace_manage);
 
 		ASSERTCMP(active, >=, 1);
@@ -886,7 +886,7 @@
 		if (purging) {
 			if (test_and_clear_bit(AFS_CELL_FL_NO_GC, &cell->flags)) {
 				active = atomic_dec_return(&cell->active);
-				trace_afs_cell(cell->debug_id, atomic_read(&cell->ref),
+				trace_afs_cell(cell->debug_id, refcount_read(&cell->ref),
 					       active, afs_cell_trace_unuse_pin);
 			}
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/cmservice.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/cmservice.c
@@ -213,7 +213,7 @@
 	 */
 	if (call->server) {
 		trace_afs_server(call->server,
-				 atomic_read(&call->server->ref),
+				 refcount_read(&call->server->ref),
 				 atomic_read(&call->server->active),
 				 afs_server_trace_callback);
 		afs_break_callbacks(call->server, call->count, call->request);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/dir.c
@@ -486,8 +486,11 @@
 		}
 
 		/* skip if starts before the current position */
-		if (offset < curr)
+		if (offset < curr) {
+			if (next > curr)
+				ctx->pos = blkoff + next * sizeof(union afs_xdr_dirent);
 			continue;
+		}
 
 		/* found the next entry */
 		if (!dir_emit(ctx, dire->u.name, nlen,
@@ -1391,6 +1394,7 @@
 	op->dentry	= dentry;
 	op->create.mode	= S_IFDIR | mode;
 	op->create.reason = afs_edit_dir_for_mkdir;
+	op->mtime	= current_time(dir);
 	op->ops		= &afs_mkdir_operation;
 	return afs_do_sync_operation(op);
 }
@@ -1489,7 +1493,12 @@
 		op->file[1].vnode = vnode;
 	}
 
-	return afs_do_sync_operation(op);
+	ret = afs_do_sync_operation(op);
+
+	/* Not all systems that can host afs servers have ENOTEMPTY. */
+	if (ret == -EEXIST)
+		ret = -ENOTEMPTY;
+	return ret;
 
 error:
 	return afs_put_operation(op);
@@ -1694,6 +1703,7 @@
 	op->dentry	= dentry;
 	op->create.mode	= S_IFREG | mode;
 	op->create.reason = afs_edit_dir_for_create;
+	op->mtime	= current_time(dir);
 	op->ops		= &afs_create_operation;
 	return afs_do_sync_operation(op);
 
@@ -1829,6 +1839,7 @@
 	op->ops			= &afs_symlink_operation;
 	op->create.reason	= afs_edit_dir_for_symlink;
 	op->create.symlink	= content;
+	op->mtime		= current_time(dir);
 	return afs_do_sync_operation(op);
 
 error:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/dynroot.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/dynroot.c
@@ -113,6 +113,7 @@
 	struct afs_net *net = afs_d2net(dentry);
 	const char *name = dentry->d_name.name;
 	size_t len = dentry->d_name.len;
+	char *result = NULL;
 	int ret;
 
 	/* Names prefixed with a dot are R/W mounts. */
@@ -130,9 +131,22 @@
 	}
 
 	ret = dns_query(net->net, "afsdb", name, len, "srv=1",
-			NULL, NULL, false);
-	if (ret == -ENODATA)
-		ret = -EDESTADDRREQ;
+			&result, NULL, false);
+	if (ret == -ENODATA || ret == -ENOKEY || ret == 0)
+		ret = -ENOENT;
+	if (ret > 0 && ret >= sizeof(struct dns_server_list_v1_header)) {
+		struct dns_server_list_v1_header *v1 = (void *)result;
+
+		if (v1->hdr.zero == 0 &&
+		    v1->hdr.content == DNS_PAYLOAD_IS_SERVER_LIST &&
+		    v1->hdr.version == 1 &&
+		    (v1->status != DNS_LOOKUP_GOOD &&
+		     v1->status != DNS_LOOKUP_GOOD_WITH_BAD))
+			return -ENOENT;
+
+	}
+
+	kfree(result);
 	return ret;
 }
 
@@ -251,20 +265,9 @@
 	return 1;
 }
 
-/*
- * Allow the VFS to enquire as to whether a dentry should be unhashed (mustn't
- * sleep)
- * - called from dput() when d_count is going to 0.
- * - return 1 to request dentry be unhashed, 0 otherwise
- */
-static int afs_dynroot_d_delete(const struct dentry *dentry)
-{
-	return d_really_is_positive(dentry);
-}
-
 const struct dentry_operations afs_dynroot_dentry_operations = {
 	.d_revalidate	= afs_dynroot_d_revalidate,
-	.d_delete	= afs_dynroot_d_delete,
+	.d_delete	= always_delete_dentry,
 	.d_release	= afs_d_release,
 	.d_automount	= afs_d_automount,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/file.c
@@ -502,8 +502,9 @@
 	if (atomic_inc_return(&vnode->cb_nr_mmap) == 1) {
 		down_write(&vnode->volume->cell->fs_open_mmaps_lock);
 
-		list_add_tail(&vnode->cb_mmap_link,
-			      &vnode->volume->cell->fs_open_mmaps);
+		if (list_empty(&vnode->cb_mmap_link))
+			list_add_tail(&vnode->cb_mmap_link,
+				      &vnode->volume->cell->fs_open_mmaps);
 
 		up_write(&vnode->volume->cell->fs_open_mmaps_lock);
 	}
@@ -511,13 +512,17 @@
 
 static void afs_drop_open_mmap(struct afs_vnode *vnode)
 {
-	if (!atomic_dec_and_test(&vnode->cb_nr_mmap))
+	if (atomic_add_unless(&vnode->cb_nr_mmap, -1, 1))
 		return;
 
 	down_write(&vnode->volume->cell->fs_open_mmaps_lock);
 
-	if (atomic_read(&vnode->cb_nr_mmap) == 0)
+	read_seqlock_excl(&vnode->cb_lock);
+	// the only place where ->cb_nr_mmap may hit 0
+	// see __afs_break_callback() for the other side...
+	if (atomic_dec_and_test(&vnode->cb_nr_mmap))
 		list_del_init(&vnode->cb_mmap_link);
+	read_sequnlock_excl(&vnode->cb_lock);
 
 	up_write(&vnode->volume->cell->fs_open_mmaps_lock);
 	flush_work(&vnode->cb_work);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/flock.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/flock.c
@@ -76,7 +76,7 @@
 	if (call->error == 0) {
 		spin_lock(&vnode->lock);
 		trace_afs_flock_ev(vnode, NULL, afs_flock_timestamp, 0);
-		vnode->locked_at = call->reply_time;
+		vnode->locked_at = call->issue_time;
 		afs_schedule_lock_extension(vnode);
 		spin_unlock(&vnode->lock);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/fs_probe.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/fs_probe.c
@@ -167,8 +167,8 @@
 			clear_bit(AFS_SERVER_FL_HAS_FS64, &server->flags);
 	}
 
-	if (rxrpc_kernel_get_srtt(call->net->socket, call->rxcall, &rtt_us) &&
-	    rtt_us < server->probe.rtt) {
+	rxrpc_kernel_get_srtt(call->net->socket, call->rxcall, &rtt_us);
+	if (rtt_us < server->probe.rtt) {
 		server->probe.rtt = rtt_us;
 		server->rtt = rtt_us;
 		alist->preferred = index;
@@ -366,12 +366,15 @@
 	unsigned long nowj, timer_at, poll_at;
 	bool first_pass = true, set_timer = false;
 
-	if (!net->live)
+	if (!net->live) {
+		afs_dec_servers_outstanding(net);
 		return;
+	}
 
 	_enter("");
 
 	if (list_empty(&net->fs_probe_fast) && list_empty(&net->fs_probe_slow)) {
+		afs_dec_servers_outstanding(net);
 		_leave(" [none]");
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/fsclient.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/fsclient.c
@@ -131,7 +131,7 @@
 
 static time64_t xdr_decode_expiry(struct afs_call *call, u32 expiry)
 {
-	return ktime_divns(call->reply_time, NSEC_PER_SEC) + expiry;
+	return ktime_divns(call->issue_time, NSEC_PER_SEC) + expiry;
 }
 
 static void xdr_decode_AFSCallBack(const __be32 **_bp,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/inode.c
@@ -219,6 +219,7 @@
 			set_bit(AFS_VNODE_ZAP_DATA, &vnode->flags);
 		}
 		change_size = true;
+		data_changed = true;
 	} else if (vnode->status.type == AFS_FTYPE_DIR) {
 		/* Expected directory change is handled elsewhere so
 		 * that we can locally edit the directory and save on a
@@ -728,10 +729,23 @@
 {
 	struct inode *inode = d_inode(path->dentry);
 	struct afs_vnode *vnode = AFS_FS_I(inode);
-	int seq = 0;
+	struct key *key;
+	int ret, seq = 0;
 
 	_enter("{ ino=%lu v=%u }", inode->i_ino, inode->i_generation);
 
+	if (vnode->volume &&
+	    !(query_flags & AT_STATX_DONT_SYNC) &&
+	    !test_bit(AFS_VNODE_CB_PROMISED, &vnode->flags)) {
+		key = afs_request_key(vnode->volume->cell);
+		if (IS_ERR(key))
+			return PTR_ERR(key);
+		ret = afs_validate(vnode, key);
+		key_put(key);
+		if (ret < 0)
+			return ret;
+	}
+
 	do {
 		read_seqbegin_or_lock(&vnode->cb_lock, &seq);
 		generic_fillattr(&init_user_ns, inode, stat);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/internal.h
@@ -123,7 +123,7 @@
 	};
 	struct afs_operation	*op;
 	unsigned int		server_index;
-	atomic_t		usage;
+	refcount_t		ref;
 	enum afs_call_state	state;
 	spinlock_t		state_lock;
 	int			error;		/* error code */
@@ -138,7 +138,6 @@
 	bool			need_attention;	/* T if RxRPC poked us */
 	bool			async;		/* T if asynchronous */
 	bool			upgrade;	/* T to request service upgrade */
-	bool			have_reply_time; /* T if have got reply_time */
 	bool			intr;		/* T if interruptible */
 	bool			unmarshalling_error; /* T if an unmarshalling error occurred */
 	u16			service_id;	/* Actual service ID (after upgrade) */
@@ -152,7 +151,7 @@
 		} __attribute__((packed));
 		__be64		tmp64;
 	};
-	ktime_t			reply_time;	/* Time of first reply packet */
+	ktime_t			issue_time;	/* Time of issue of operation */
 };
 
 struct afs_call_type {
@@ -369,7 +368,7 @@
 #endif
 	time64_t		dns_expiry;	/* Time AFSDB/SRV record expires */
 	time64_t		last_inactive;	/* Time of last drop of usage count */
-	atomic_t		ref;		/* Struct refcount */
+	refcount_t		ref;		/* Struct refcount */
 	atomic_t		active;		/* Active usage counter */
 	unsigned long		flags;
 #define AFS_CELL_FL_NO_GC	0		/* The cell was added manually, don't auto-gc */
@@ -383,6 +382,7 @@
 	unsigned int		debug_id;
 
 	/* The volumes belonging to this cell */
+	spinlock_t		vs_lock;	/* Lock for server->volumes */
 	struct rb_root		volumes;	/* Tree of volumes on this server */
 	struct hlist_head	proc_volumes;	/* procfs volume list */
 	seqlock_t		volume_lock;	/* For volumes */
@@ -414,7 +414,7 @@
 #define AFS_VLSERVER_FL_IS_YFS	2		/* Server is YFS not AFS */
 #define AFS_VLSERVER_FL_RESPONDING 3		/* VL server is responding */
 	rwlock_t		lock;		/* Lock on addresses */
-	atomic_t		usage;
+	refcount_t		ref;
 	unsigned int		rtt;		/* Server's current RTT in uS */
 
 	/* Probe state */
@@ -450,7 +450,7 @@
 
 struct afs_vlserver_list {
 	struct rcu_head		rcu;
-	atomic_t		usage;
+	refcount_t		ref;
 	u8			nr_servers;
 	u8			index;		/* Server currently in use */
 	u8			preferred;	/* Preferred server */
@@ -506,6 +506,7 @@
 	struct hlist_node	addr4_link;	/* Link in net->fs_addresses4 */
 	struct hlist_node	addr6_link;	/* Link in net->fs_addresses6 */
 	struct hlist_node	proc_link;	/* Link in net->fs_proc */
+	struct list_head	volumes;	/* RCU list of afs_server_entry objects */
 	struct work_struct	initcb_work;	/* Work for CB.InitCallBackState* */
 	struct afs_server	*gc_next;	/* Next server in manager's list */
 	time64_t		unuse_time;	/* Time at which last unused */
@@ -521,7 +522,7 @@
 #define AFS_SERVER_FL_NO_IBULK	17		/* Fileserver doesn't support FS.InlineBulkStatus */
 #define AFS_SERVER_FL_NO_RM2	18		/* Fileserver doesn't support YFS.RemoveFile2 */
 #define AFS_SERVER_FL_HAS_FS64	19		/* Fileserver supports FS.{Fetch,Store}Data64 */
-	atomic_t		ref;		/* Object refcount */
+	refcount_t		ref;		/* Object refcount */
 	atomic_t		active;		/* Active user count */
 	u32			addr_version;	/* Address list version */
 	unsigned int		rtt;		/* Server's current RTT in uS */
@@ -554,11 +555,14 @@
  */
 struct afs_server_entry {
 	struct afs_server	*server;
+	struct afs_volume	*volume;
+	struct list_head	slink;		/* Link in server->volumes */
 };
 
 struct afs_server_list {
-	afs_volid_t		vids[AFS_MAXTYPES]; /* Volume IDs */
+	struct rcu_head		rcu;
 	refcount_t		usage;
+	bool			attached;	/* T if attached to servers */
 	unsigned char		nr_servers;
 	unsigned char		preferred;	/* Preferred server */
 	unsigned short		vnovol_mask;	/* Servers to be skipped due to VNOVOL */
@@ -571,11 +575,10 @@
  * Live AFS volume management.
  */
 struct afs_volume {
-	union {
-		struct rcu_head	rcu;
-		afs_volid_t	vid;		/* volume ID */
-	};
-	atomic_t		usage;
+	struct rcu_head	rcu;
+	afs_volid_t		vid;		/* The volume ID of this volume */
+	afs_volid_t		vids[AFS_MAXTYPES]; /* All associated volume IDs */
+	refcount_t		ref;
 	time64_t		update_at;	/* Time at which to next update */
 	struct afs_cell		*cell;		/* Cell to which belongs (pins ref) */
 	struct rb_node		cell_node;	/* Link in cell->volumes */
@@ -589,6 +592,7 @@
 #define AFS_VOLUME_OFFLINE	4	/* - T if volume offline notice given */
 #define AFS_VOLUME_BUSY		5	/* - T if volume busy notice given */
 #define AFS_VOLUME_MAYBE_NO_IBULK 6	/* - T if some servers don't have InlineBulkStatus */
+#define AFS_VOLUME_RM_TREE	7	/* - Set if volume removed from cell->volumes */
 #ifdef CONFIG_AFS_FSCACHE
 	struct fscache_cookie	*cache;		/* caching cookie */
 #endif
@@ -1435,10 +1439,14 @@
 }
 
 extern void afs_put_serverlist(struct afs_net *, struct afs_server_list *);
-extern struct afs_server_list *afs_alloc_server_list(struct afs_cell *, struct key *,
-						     struct afs_vldb_entry *,
-						     u8);
+struct afs_server_list *afs_alloc_server_list(struct afs_volume *volume,
+					      struct key *key,
+					      struct afs_vldb_entry *vldb);
 extern bool afs_annotate_server_list(struct afs_server_list *, struct afs_server_list *);
+void afs_attach_volume_to_servers(struct afs_volume *volume, struct afs_server_list *slist);
+void afs_reattach_volume_to_servers(struct afs_volume *volume, struct afs_server_list *slist,
+				    struct afs_server_list *old);
+void afs_detach_volume_from_servers(struct afs_volume *volume, struct afs_server_list *slist);
 
 /*
  * super.c
@@ -1483,14 +1491,14 @@
  */
 static inline struct afs_vlserver *afs_get_vlserver(struct afs_vlserver *vlserver)
 {
-	atomic_inc(&vlserver->usage);
+	refcount_inc(&vlserver->ref);
 	return vlserver;
 }
 
 static inline struct afs_vlserver_list *afs_get_vlserverlist(struct afs_vlserver_list *vllist)
 {
 	if (vllist)
-		atomic_inc(&vllist->usage);
+		refcount_inc(&vllist->ref);
 	return vllist;
 }
 
@@ -1507,6 +1515,7 @@
 extern struct afs_volume *afs_create_volume(struct afs_fs_context *);
 extern void afs_activate_volume(struct afs_volume *);
 extern void afs_deactivate_volume(struct afs_volume *);
+bool afs_try_get_volume(struct afs_volume *volume, enum afs_volume_trace reason);
 extern struct afs_volume *afs_get_volume(struct afs_volume *, enum afs_volume_trace);
 extern void afs_put_volume(struct afs_net *, struct afs_volume *, enum afs_volume_trace);
 extern int afs_check_volume_status(struct afs_volume *, struct afs_operation *);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/misc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/misc.c
@@ -69,6 +69,7 @@
 		/* Unified AFS error table */
 	case UAEPERM:			return -EPERM;
 	case UAENOENT:			return -ENOENT;
+	case UAEAGAIN:			return -EAGAIN;
 	case UAEACCES:			return -EACCES;
 	case UAEBUSY:			return -EBUSY;
 	case UAEEXIST:			return -EEXIST;
@@ -163,8 +164,11 @@
 		return;
 
 	case -ECONNABORTED:
+		error = afs_abort_to_error(abort_code);
+		fallthrough;
+	case -ENETRESET: /* Responded, but we seem to have changed address */
 		e->responded = true;
-		e->error = afs_abort_to_error(abort_code);
+		e->error = error;
 		return;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/mntpt.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/mntpt.c
@@ -146,6 +146,11 @@
 		put_page(page);
 		if (ret < 0)
 			return ret;
+
+		/* Don't cross a backup volume mountpoint from a backup volume */
+		if (src_as->volume && src_as->volume->type == AFSVL_BACKVOL &&
+		    ctx->type == AFSVL_BACKVOL)
+			return -ENODEV;
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/proc.c
@@ -47,7 +47,7 @@
 
 	/* display one cell per line on subsequent lines */
 	seq_printf(m, "%3u %3u %6lld %2u %2u %s\n",
-		   atomic_read(&cell->ref),
+		   refcount_read(&cell->ref),
 		   atomic_read(&cell->active),
 		   cell->dns_expiry - ktime_get_real_seconds(),
 		   vllist ? vllist->nr_servers : 0,
@@ -217,7 +217,7 @@
 	}
 
 	seq_printf(m, "%3d %08llx %s %s\n",
-		   atomic_read(&vol->usage), vol->vid,
+		   refcount_read(&vol->ref), vol->vid,
 		   afs_vol_types[vol->type],
 		   vol->name);
 
@@ -388,7 +388,7 @@
 	alist = rcu_dereference(server->addresses);
 	seq_printf(m, "%pU %3d %3d\n",
 		   &server->uuid,
-		   atomic_read(&server->ref),
+		   refcount_read(&server->ref),
 		   atomic_read(&server->active));
 	seq_printf(m, "  - info: fl=%lx rtt=%u brk=%x\n",
 		   server->flags, server->rtt, server->cb_s_break);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/rotate.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/rotate.c
@@ -292,6 +292,10 @@
 		op->error = error;
 		goto iterate_address;
 
+	case -ENETRESET:
+		pr_warn("kAFS: Peer reset %s (op=%x)\n",
+			op->type ? op->type->name : "???", op->debug_id);
+		fallthrough;
 	case -ECONNRESET:
 		_debug("call reset");
 		op->error = error;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/rxrpc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/rxrpc.c
@@ -145,7 +145,7 @@
 	call->type = type;
 	call->net = net;
 	call->debug_id = atomic_inc_return(&rxrpc_debug_id);
-	atomic_set(&call->usage, 1);
+	refcount_set(&call->ref, 1);
 	INIT_WORK(&call->async_work, afs_process_async_call);
 	init_waitqueue_head(&call->waitq);
 	spin_lock_init(&call->state_lock);
@@ -163,14 +163,15 @@
 void afs_put_call(struct afs_call *call)
 {
 	struct afs_net *net = call->net;
-	int n = atomic_dec_return(&call->usage);
-	int o = atomic_read(&net->nr_outstanding_calls);
+	bool zero;
+	int r, o;
 
-	trace_afs_call(call, afs_call_trace_put, n, o,
+	zero = __refcount_dec_and_test(&call->ref, &r);
+	o = atomic_read(&net->nr_outstanding_calls);
+	trace_afs_call(call, afs_call_trace_put, r - 1, o,
 		       __builtin_return_address(0));
 
-	ASSERTCMP(n, >=, 0);
-	if (n == 0) {
+	if (zero) {
 		ASSERT(!work_pending(&call->async_work));
 		ASSERT(call->type->name != NULL);
 
@@ -198,9 +199,11 @@
 static struct afs_call *afs_get_call(struct afs_call *call,
 				     enum afs_call_trace why)
 {
-	int u = atomic_inc_return(&call->usage);
+	int r;
 
-	trace_afs_call(call, why, u,
+	__refcount_inc(&call->ref, &r);
+
+	trace_afs_call(call, why, r + 1,
 		       atomic_read(&call->net->nr_outstanding_calls),
 		       __builtin_return_address(0));
 	return call;
@@ -347,6 +350,7 @@
 	if (call->max_lifespan)
 		rxrpc_kernel_set_max_life(call->net->socket, rxcall,
 					  call->max_lifespan);
+	call->issue_time = ktime_get_real();
 
 	/* send the request */
 	iov[0].iov_base	= call->request;
@@ -419,7 +423,7 @@
 	if (call->async) {
 		if (cancel_work_sync(&call->async_work))
 			afs_put_call(call);
-		afs_put_call(call);
+		afs_set_call_complete(call, ret, 0);
 	}
 
 	ac->error = ret;
@@ -497,12 +501,6 @@
 			return;
 		}
 
-		if (!call->have_reply_time &&
-		    rxrpc_kernel_get_reply_time(call->net->socket,
-						call->rxcall,
-						&call->reply_time))
-			call->have_reply_time = true;
-
 		ret = call->type->deliver(call);
 		state = READ_ONCE(call->state);
 		if (ret == 0 && call->unmarshalling_error)
@@ -537,6 +535,8 @@
 		case -ENODATA:
 		case -EBADMSG:
 		case -EMSGSIZE:
+		case -ENOMEM:
+		case -EFAULT:
 			abort_code = RXGEN_CC_UNMARSHAL;
 			if (state != AFS_CALL_CL_AWAIT_REPLY)
 				abort_code = RXGEN_SS_UNMARSHAL;
@@ -544,7 +544,7 @@
 						abort_code, ret, "KUM");
 			goto local_abort;
 		default:
-			abort_code = RX_USER_ABORT;
+			abort_code = RX_CALL_DEAD;
 			rxrpc_kernel_abort_call(call->net->socket, call->rxcall,
 						abort_code, ret, "KER");
 			goto local_abort;
@@ -666,14 +666,13 @@
 				   unsigned long call_user_ID)
 {
 	struct afs_call *call = (struct afs_call *)call_user_ID;
-	int u;
+	int r;
 
 	trace_afs_notify_call(rxcall, call);
 	call->need_attention = true;
 
-	u = atomic_fetch_add_unless(&call->usage, 1, 0);
-	if (u != 0) {
-		trace_afs_call(call, afs_call_trace_wake, u + 1,
+	if (__refcount_inc_not_zero(&call->ref, &r)) {
+		trace_afs_call(call, afs_call_trace_wake, r + 1,
 			       atomic_read(&call->net->nr_outstanding_calls),
 			       __builtin_return_address(0));
 
@@ -836,7 +835,7 @@
 	case -ENOMEM:
 		_debug("oom");
 		rxrpc_kernel_abort_call(net->socket, call->rxcall,
-					RX_USER_ABORT, -ENOMEM, "KOO");
+					RXGEN_SS_MARSHAL, -ENOMEM, "KOO");
 		fallthrough;
 	default:
 		_leave(" [error]");
@@ -878,7 +877,7 @@
 	if (n == -ENOMEM) {
 		_debug("oom");
 		rxrpc_kernel_abort_call(net->socket, call->rxcall,
-					RX_USER_ABORT, -ENOMEM, "KOO");
+					RXGEN_SS_MARSHAL, -ENOMEM, "KOO");
 	}
 	_leave(" [error]");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/server.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/server.c
@@ -27,7 +27,7 @@
 	const struct afs_addr_list *alist;
 	struct afs_server *server = NULL;
 	unsigned int i;
-	int seq = 0, diff;
+	int seq = 1, diff;
 
 	rcu_read_lock();
 
@@ -35,6 +35,7 @@
 		if (server)
 			afs_unuse_server_notime(net, server, afs_server_trace_put_find_rsq);
 		server = NULL;
+		seq++; /* 2 on the 1st/lockless path, otherwise odd */
 		read_seqbegin_or_lock(&net->fs_addr_lock, &seq);
 
 		if (srx->transport.family == AF_INET6) {
@@ -90,7 +91,7 @@
 {
 	struct afs_server *server = NULL;
 	struct rb_node *p;
-	int diff, seq = 0;
+	int diff, seq = 1;
 
 	_enter("%pU", uuid);
 
@@ -102,7 +103,7 @@
 		if (server)
 			afs_unuse_server(net, server, afs_server_trace_put_uuid_rsq);
 		server = NULL;
-
+		seq++; /* 2 on the 1st/lockless path, otherwise odd */
 		read_seqbegin_or_lock(&net->fs_lock, &seq);
 
 		p = net->fs_servers.rb_node;
@@ -228,13 +229,14 @@
 	if (!server)
 		goto enomem;
 
-	atomic_set(&server->ref, 1);
+	refcount_set(&server->ref, 1);
 	atomic_set(&server->active, 1);
 	server->debug_id = atomic_inc_return(&afs_server_debug_id);
 	RCU_INIT_POINTER(server->addresses, alist);
 	server->addr_version = alist->version;
 	server->uuid = *uuid;
 	rwlock_init(&server->fs_lock);
+	INIT_LIST_HEAD(&server->volumes);
 	INIT_WORK(&server->initcb_work, afs_server_init_callback_work);
 	init_waitqueue_head(&server->probe_wq);
 	INIT_LIST_HEAD(&server->probe_link);
@@ -352,9 +354,10 @@
 struct afs_server *afs_get_server(struct afs_server *server,
 				  enum afs_server_trace reason)
 {
-	unsigned int u = atomic_inc_return(&server->ref);
+	int r;
 
-	trace_afs_server(server, u, atomic_read(&server->active), reason);
+	__refcount_inc(&server->ref, &r);
+	trace_afs_server(server, r + 1, atomic_read(&server->active), reason);
 	return server;
 }
 
@@ -364,14 +367,14 @@
 static struct afs_server *afs_maybe_use_server(struct afs_server *server,
 					       enum afs_server_trace reason)
 {
-	unsigned int r = atomic_fetch_add_unless(&server->ref, 1, 0);
 	unsigned int a;
+	int r;
 
-	if (r == 0)
+	if (!__refcount_inc_not_zero(&server->ref, &r))
 		return NULL;
 
 	a = atomic_inc_return(&server->active);
-	trace_afs_server(server, r, a, reason);
+	trace_afs_server(server, r + 1, a, reason);
 	return server;
 }
 
@@ -380,10 +383,13 @@
  */
 struct afs_server *afs_use_server(struct afs_server *server, enum afs_server_trace reason)
 {
-	unsigned int r = atomic_inc_return(&server->ref);
-	unsigned int a = atomic_inc_return(&server->active);
+	unsigned int a;
+	int r;
+
+	__refcount_inc(&server->ref, &r);
+	a = atomic_inc_return(&server->active);
 
-	trace_afs_server(server, r, a, reason);
+	trace_afs_server(server, r + 1, a, reason);
 	return server;
 }
 
@@ -393,14 +399,15 @@
 void afs_put_server(struct afs_net *net, struct afs_server *server,
 		    enum afs_server_trace reason)
 {
-	unsigned int usage;
+	bool zero;
+	int r;
 
 	if (!server)
 		return;
 
-	usage = atomic_dec_return(&server->ref);
-	trace_afs_server(server, usage, atomic_read(&server->active), reason);
-	if (unlikely(usage == 0))
+	zero = __refcount_dec_and_test(&server->ref, &r);
+	trace_afs_server(server, r - 1, atomic_read(&server->active), reason);
+	if (unlikely(zero))
 		__afs_put_server(net, server);
 }
 
@@ -436,7 +443,7 @@
 {
 	struct afs_server *server = container_of(rcu, struct afs_server, rcu);
 
-	trace_afs_server(server, atomic_read(&server->ref),
+	trace_afs_server(server, refcount_read(&server->ref),
 			 atomic_read(&server->active), afs_server_trace_free);
 	afs_put_addrlist(rcu_access_pointer(server->addresses));
 	kfree(server);
@@ -487,7 +494,7 @@
 
 		active = atomic_read(&server->active);
 		if (active == 0) {
-			trace_afs_server(server, atomic_read(&server->ref),
+			trace_afs_server(server, refcount_read(&server->ref),
 					 active, afs_server_trace_gc);
 			next = rcu_dereference_protected(
 				server->uuid_next, lockdep_is_held(&net->fs_lock.lock));
@@ -553,7 +560,7 @@
 		_debug("manage %pU %u", &server->uuid, active);
 
 		if (purging) {
-			trace_afs_server(server, atomic_read(&server->ref),
+			trace_afs_server(server, refcount_read(&server->ref),
 					 active, afs_server_trace_purging);
 			if (active != 0)
 				pr_notice("Can't purge s=%08x\n", server->debug_id);
@@ -633,7 +640,8 @@
 
 	_enter("");
 
-	trace_afs_server(server, atomic_read(&server->ref), atomic_read(&server->active),
+	trace_afs_server(server, refcount_read(&server->ref),
+			 atomic_read(&server->active),
 			 afs_server_trace_update);
 
 	alist = afs_vl_lookup_addrs(op->volume->cell, op->key, &server->uuid);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/server_list.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/server_list.c
@@ -17,20 +17,20 @@
 		for (i = 0; i < slist->nr_servers; i++)
 			afs_unuse_server(net, slist->servers[i].server,
 					 afs_server_trace_put_slist);
-		kfree(slist);
+		kfree_rcu(slist, rcu);
 	}
 }
 
 /*
  * Build a server list from a VLDB record.
  */
-struct afs_server_list *afs_alloc_server_list(struct afs_cell *cell,
+struct afs_server_list *afs_alloc_server_list(struct afs_volume *volume,
 					      struct key *key,
-					      struct afs_vldb_entry *vldb,
-					      u8 type_mask)
+					      struct afs_vldb_entry *vldb)
 {
 	struct afs_server_list *slist;
 	struct afs_server *server;
+	unsigned int type_mask = 1 << volume->type;
 	int ret = -ENOMEM, nr_servers = 0, i, j;
 
 	for (i = 0; i < vldb->nr_servers; i++)
@@ -44,15 +44,12 @@
 	refcount_set(&slist->usage, 1);
 	rwlock_init(&slist->lock);
 
-	for (i = 0; i < AFS_MAXTYPES; i++)
-		slist->vids[i] = vldb->vid[i];
-
 	/* Make sure a records exists for each server in the list. */
 	for (i = 0; i < vldb->nr_servers; i++) {
 		if (!(vldb->fs_mask[i] & type_mask))
 			continue;
 
-		server = afs_lookup_server(cell, key, &vldb->fs_server[i],
+		server = afs_lookup_server(volume->cell, key, &vldb->fs_server[i],
 					   vldb->addr_version[i]);
 		if (IS_ERR(server)) {
 			ret = PTR_ERR(server);
@@ -70,8 +67,8 @@
 				break;
 		if (j < slist->nr_servers) {
 			if (slist->servers[j].server == server) {
-				afs_put_server(cell->net, server,
-					       afs_server_trace_put_slist_isort);
+				afs_unuse_server(volume->cell->net, server,
+						 afs_server_trace_put_slist_isort);
 				continue;
 			}
 
@@ -81,6 +78,7 @@
 		}
 
 		slist->servers[j].server = server;
+		slist->servers[j].volume = volume;
 		slist->nr_servers++;
 	}
 
@@ -92,7 +90,7 @@
 	return slist;
 
 error_2:
-	afs_put_serverlist(cell->net, slist);
+	afs_put_serverlist(volume->cell->net, slist);
 error:
 	return ERR_PTR(ret);
 }
@@ -127,3 +125,99 @@
 
 	return true;
 }
+
+/*
+ * Attach a volume to the servers it is going to use.
+ */
+void afs_attach_volume_to_servers(struct afs_volume *volume, struct afs_server_list *slist)
+{
+	struct afs_server_entry *se, *pe;
+	struct afs_server *server;
+	struct list_head *p;
+	unsigned int i;
+
+	spin_lock(&volume->cell->vs_lock);
+
+	for (i = 0; i < slist->nr_servers; i++) {
+		se = &slist->servers[i];
+		server = se->server;
+
+		list_for_each(p, &server->volumes) {
+			pe = list_entry(p, struct afs_server_entry, slink);
+			if (volume->vid <= pe->volume->vid)
+				break;
+		}
+		list_add_tail_rcu(&se->slink, p);
+	}
+
+	slist->attached = true;
+	spin_unlock(&volume->cell->vs_lock);
+}
+
+/*
+ * Reattach a volume to the servers it is going to use when server list is
+ * replaced.  We try to switch the attachment points to avoid rewalking the
+ * lists.
+ */
+void afs_reattach_volume_to_servers(struct afs_volume *volume, struct afs_server_list *new,
+				    struct afs_server_list *old)
+{
+	unsigned int n = 0, o = 0;
+
+	spin_lock(&volume->cell->vs_lock);
+
+	while (n < new->nr_servers || o < old->nr_servers) {
+		struct afs_server_entry *pn = n < new->nr_servers ? &new->servers[n] : NULL;
+		struct afs_server_entry *po = o < old->nr_servers ? &old->servers[o] : NULL;
+		struct afs_server_entry *s;
+		struct list_head *p;
+		int diff;
+
+		if (pn && po && pn->server == po->server) {
+			list_replace_rcu(&po->slink, &pn->slink);
+			n++;
+			o++;
+			continue;
+		}
+
+		if (pn && po)
+			diff = memcmp(&pn->server->uuid, &po->server->uuid,
+				      sizeof(pn->server->uuid));
+		else
+			diff = pn ? -1 : 1;
+
+		if (diff < 0) {
+			list_for_each(p, &pn->server->volumes) {
+				s = list_entry(p, struct afs_server_entry, slink);
+				if (volume->vid <= s->volume->vid)
+					break;
+			}
+			list_add_tail_rcu(&pn->slink, p);
+			n++;
+		} else {
+			list_del_rcu(&po->slink);
+			o++;
+		}
+	}
+
+	spin_unlock(&volume->cell->vs_lock);
+}
+
+/*
+ * Detach a volume from the servers it has been using.
+ */
+void afs_detach_volume_from_servers(struct afs_volume *volume, struct afs_server_list *slist)
+{
+	unsigned int i;
+
+	if (!slist->attached)
+		return;
+
+	spin_lock(&volume->cell->vs_lock);
+
+	for (i = 0; i < slist->nr_servers; i++)
+		list_del_rcu(&slist->servers[i].slink);
+
+	slist->attached = false;
+	spin_unlock(&volume->cell->vs_lock);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/super.c
@@ -406,6 +406,8 @@
 			return PTR_ERR(volume);
 
 		ctx->volume = volume;
+		if (volume->type != AFSVL_RWVOL)
+			ctx->flock_mode = afs_flock_mode_local;
 	}
 
 	return 0;
@@ -667,6 +669,7 @@
 	INIT_LIST_HEAD(&vnode->pending_locks);
 	INIT_LIST_HEAD(&vnode->granted_locks);
 	INIT_DELAYED_WORK(&vnode->lock_work, afs_lock_work);
+	INIT_LIST_HEAD(&vnode->cb_mmap_link);
 	seqlock_init(&vnode->cb_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/vl_alias.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/vl_alias.c
@@ -126,7 +126,7 @@
 	lb = rcu_dereference(vol_b->servers);
 
 	for (i = 0; i < AFS_MAXTYPES; i++)
-		if (la->vids[i] != lb->vids[i])
+		if (vol_a->vids[i] != vol_b->vids[i])
 			return 0;
 
 	while (a < la->nr_servers && b < lb->nr_servers) {
@@ -302,6 +302,7 @@
 static int yfs_check_canonical_cell_name(struct afs_cell *cell, struct key *key)
 {
 	struct afs_cell *master;
+	size_t name_len;
 	char *cell_name;
 
 	cell_name = afs_vl_get_cell_name(cell, key);
@@ -313,8 +314,11 @@
 		return 0;
 	}
 
-	master = afs_lookup_cell(cell->net, cell_name, strlen(cell_name),
-				 NULL, false);
+	name_len = strlen(cell_name);
+	if (!name_len || name_len > AFS_MAXCELLNAME)
+		master = ERR_PTR(-EOPNOTSUPP);
+	else
+		master = afs_lookup_cell(cell->net, cell_name, name_len, NULL, false);
 	kfree(cell_name);
 	if (IS_ERR(master))
 		return PTR_ERR(master);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/vl_list.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/vl_list.c
@@ -17,7 +17,7 @@
 	vlserver = kzalloc(struct_size(vlserver, name, name_len + 1),
 			   GFP_KERNEL);
 	if (vlserver) {
-		atomic_set(&vlserver->usage, 1);
+		refcount_set(&vlserver->ref, 1);
 		rwlock_init(&vlserver->lock);
 		init_waitqueue_head(&vlserver->probe_wq);
 		spin_lock_init(&vlserver->probe_lock);
@@ -39,13 +39,9 @@
 
 void afs_put_vlserver(struct afs_net *net, struct afs_vlserver *vlserver)
 {
-	if (vlserver) {
-		unsigned int u = atomic_dec_return(&vlserver->usage);
-		//_debug("VL PUT %p{%u}", vlserver, u);
-
-		if (u == 0)
-			call_rcu(&vlserver->rcu, afs_vlserver_rcu);
-	}
+	if (vlserver &&
+	    refcount_dec_and_test(&vlserver->ref))
+		call_rcu(&vlserver->rcu, afs_vlserver_rcu);
 }
 
 struct afs_vlserver_list *afs_alloc_vlserver_list(unsigned int nr_servers)
@@ -54,7 +50,7 @@
 
 	vllist = kzalloc(struct_size(vllist, servers, nr_servers), GFP_KERNEL);
 	if (vllist) {
-		atomic_set(&vllist->usage, 1);
+		refcount_set(&vllist->ref, 1);
 		rwlock_init(&vllist->lock);
 	}
 
@@ -64,10 +60,7 @@
 void afs_put_vlserverlist(struct afs_net *net, struct afs_vlserver_list *vllist)
 {
 	if (vllist) {
-		unsigned int u = atomic_dec_return(&vllist->usage);
-
-		//_debug("VLLS PUT %p{%u}", vllist, u);
-		if (u == 0) {
+		if (refcount_dec_and_test(&vllist->ref)) {
 			int i;
 
 			for (i = 0; i < vllist->nr_servers; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/vl_probe.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/vl_probe.c
@@ -115,8 +115,8 @@
 		}
 	}
 
-	if (rxrpc_kernel_get_srtt(call->net->socket, call->rxcall, &rtt_us) &&
-	    rtt_us < server->probe.rtt) {
+	rxrpc_kernel_get_srtt(call->net->socket, call->rxcall, &rtt_us);
+	if (rtt_us < server->probe.rtt) {
 		server->probe.rtt = rtt_us;
 		server->rtt = rtt_us;
 		alist->preferred = index;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/vl_rotate.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/vl_rotate.c
@@ -58,6 +58,12 @@
 		}
 
 		/* Status load is ordered after lookup counter load */
+		if (cell->dns_status == DNS_LOOKUP_GOT_NOT_FOUND) {
+			pr_warn("No record of cell %s\n", cell->name);
+			vc->error = -ENOENT;
+			return false;
+		}
+
 		if (cell->dns_source == DNS_RECORD_UNAVAILABLE) {
 			vc->error = -EDESTADDRREQ;
 			return false;
@@ -285,6 +291,7 @@
  */
 static void afs_vl_dump_edestaddrreq(const struct afs_vl_cursor *vc)
 {
+	struct afs_cell *cell = vc->cell;
 	static int count;
 	int i;
 
@@ -294,6 +301,9 @@
 
 	rcu_read_lock();
 	pr_notice("EDESTADDR occurred\n");
+	pr_notice("CELL: %s err=%d\n", cell->name, cell->error);
+	pr_notice("DNS: src=%u st=%u lc=%x\n",
+		  cell->dns_source, cell->dns_status, cell->dns_lookup_count);
 	pr_notice("VC: ut=%lx ix=%u ni=%hu fl=%hx err=%hd\n",
 		  vc->untried, vc->index, vc->nr_iterations, vc->flags, vc->error);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/vlclient.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/vlclient.c
@@ -671,7 +671,7 @@
 			return ret;
 
 		namesz = ntohl(call->tmp);
-		if (namesz > AFS_MAXCELLNAME)
+		if (namesz > YFS_VL_MAXCELLNAME)
 			return afs_protocol_error(call, afs_eproto_cellname_len);
 		paddedsz = (namesz + 3) & ~3;
 		call->count = namesz;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/volume.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/volume.c
@@ -33,8 +33,13 @@
 		} else if (p->vid > volume->vid) {
 			pp = &(*pp)->rb_right;
 		} else {
-			volume = afs_get_volume(p, afs_volume_trace_get_cell_insert);
-			goto found;
+			if (afs_try_get_volume(p, afs_volume_trace_get_cell_insert)) {
+				volume = p;
+				goto found;
+			}
+
+			set_bit(AFS_VOLUME_RM_TREE, &volume->flags);
+			rb_replace_node_rcu(&p->cell_node, &volume->cell_node, &cell->volumes);
 		}
 	}
 
@@ -53,11 +58,12 @@
 	struct afs_cell *cell = volume->cell;
 
 	if (!hlist_unhashed(&volume->proc_link)) {
-		trace_afs_volume(volume->vid, atomic_read(&volume->usage),
+		trace_afs_volume(volume->vid, refcount_read(&cell->ref),
 				 afs_volume_trace_remove);
 		write_seqlock(&cell->volume_lock);
 		hlist_del_rcu(&volume->proc_link);
-		rb_erase(&volume->cell_node, &cell->volumes);
+		if (!test_and_set_bit(AFS_VOLUME_RM_TREE, &volume->flags))
+			rb_erase(&volume->cell_node, &cell->volumes);
 		write_sequnlock(&cell->volume_lock);
 	}
 }
@@ -67,15 +73,11 @@
  */
 static struct afs_volume *afs_alloc_volume(struct afs_fs_context *params,
 					   struct afs_vldb_entry *vldb,
-					   unsigned long type_mask)
+					   struct afs_server_list **_slist)
 {
 	struct afs_server_list *slist;
 	struct afs_volume *volume;
-	int ret = -ENOMEM, nr_servers = 0, i;
-
-	for (i = 0; i < vldb->nr_servers; i++)
-		if (vldb->fs_mask[i] & type_mask)
-			nr_servers++;
+	int ret = -ENOMEM, i;
 
 	volume = kzalloc(sizeof(struct afs_volume), GFP_KERNEL);
 	if (!volume)
@@ -88,19 +90,22 @@
 	volume->type_force	= params->force;
 	volume->name_len	= vldb->name_len;
 
-	atomic_set(&volume->usage, 1);
+	refcount_set(&volume->ref, 1);
 	INIT_HLIST_NODE(&volume->proc_link);
 	rwlock_init(&volume->servers_lock);
 	rwlock_init(&volume->cb_v_break_lock);
 	memcpy(volume->name, vldb->name, vldb->name_len + 1);
 
-	slist = afs_alloc_server_list(params->cell, params->key, vldb, type_mask);
+	for (i = 0; i < AFS_MAXTYPES; i++)
+		volume->vids[i] = vldb->vid[i];
+
+	slist = afs_alloc_server_list(volume, params->key, vldb);
 	if (IS_ERR(slist)) {
 		ret = PTR_ERR(slist);
 		goto error_1;
 	}
 
-	refcount_set(&slist->usage, 1);
+	*_slist = slist;
 	rcu_assign_pointer(volume->servers, slist);
 	trace_afs_volume(volume->vid, 1, afs_volume_trace_alloc);
 	return volume;
@@ -116,17 +121,19 @@
  * Look up or allocate a volume record.
  */
 static struct afs_volume *afs_lookup_volume(struct afs_fs_context *params,
-					    struct afs_vldb_entry *vldb,
-					    unsigned long type_mask)
+					    struct afs_vldb_entry *vldb)
 {
+	struct afs_server_list *slist;
 	struct afs_volume *candidate, *volume;
 
-	candidate = afs_alloc_volume(params, vldb, type_mask);
+	candidate = afs_alloc_volume(params, vldb, &slist);
 	if (IS_ERR(candidate))
 		return candidate;
 
 	volume = afs_insert_volume_into_cell(params->cell, candidate);
-	if (volume != candidate)
+	if (volume == candidate)
+		afs_attach_volume_to_servers(volume, slist);
+	else
 		afs_put_volume(params->net, candidate, afs_volume_trace_put_cell_dup);
 	return volume;
 }
@@ -207,8 +214,7 @@
 		goto error;
 	}
 
-	type_mask = 1UL << params->type;
-	volume = afs_lookup_volume(params, vldb, type_mask);
+	volume = afs_lookup_volume(params, vldb);
 
 error:
 	kfree(vldb);
@@ -220,16 +226,19 @@
  */
 static void afs_destroy_volume(struct afs_net *net, struct afs_volume *volume)
 {
+	struct afs_server_list *slist = rcu_access_pointer(volume->servers);
+
 	_enter("%p", volume);
 
 #ifdef CONFIG_AFS_FSCACHE
 	ASSERTCMP(volume->cache, ==, NULL);
 #endif
 
+	afs_detach_volume_from_servers(volume, slist);
 	afs_remove_volume_from_cell(volume);
-	afs_put_serverlist(net, rcu_access_pointer(volume->servers));
+	afs_put_serverlist(net, slist);
 	afs_put_cell(volume->cell, afs_cell_trace_put_vol);
-	trace_afs_volume(volume->vid, atomic_read(&volume->usage),
+	trace_afs_volume(volume->vid, refcount_read(&volume->ref),
 			 afs_volume_trace_free);
 	kfree_rcu(volume, rcu);
 
@@ -237,14 +246,30 @@
 }
 
 /*
+ * Try to get a reference on a volume record.
+ */
+bool afs_try_get_volume(struct afs_volume *volume, enum afs_volume_trace reason)
+{
+	int r;
+
+	if (__refcount_inc_not_zero(&volume->ref, &r)) {
+		trace_afs_volume(volume->vid, r + 1, reason);
+		return true;
+	}
+	return false;
+}
+
+/*
  * Get a reference on a volume record.
  */
 struct afs_volume *afs_get_volume(struct afs_volume *volume,
 				  enum afs_volume_trace reason)
 {
 	if (volume) {
-		int u = atomic_inc_return(&volume->usage);
-		trace_afs_volume(volume->vid, u, reason);
+		int r;
+
+		__refcount_inc(&volume->ref, &r);
+		trace_afs_volume(volume->vid, r + 1, reason);
 	}
 	return volume;
 }
@@ -258,9 +283,12 @@
 {
 	if (volume) {
 		afs_volid_t vid = volume->vid;
-		int u = atomic_dec_return(&volume->usage);
-		trace_afs_volume(vid, u, reason);
-		if (u == 0)
+		bool zero;
+		int r;
+
+		zero = __refcount_dec_and_test(&volume->ref, &r);
+		trace_afs_volume(vid, r - 1, reason);
+		if (zero)
 			afs_destroy_volume(net, volume);
 	}
 }
@@ -302,7 +330,7 @@
 {
 	struct afs_server_list *new, *old, *discard;
 	struct afs_vldb_entry *vldb;
-	char idbuf[16];
+	char idbuf[24];
 	int ret, idsz;
 
 	_enter("");
@@ -310,7 +338,7 @@
 	/* We look up an ID by passing it as a decimal string in the
 	 * operation's name parameter.
 	 */
-	idsz = sprintf(idbuf, "%llu", volume->vid);
+	idsz = snprintf(idbuf, sizeof(idbuf), "%llu", volume->vid);
 
 	vldb = afs_vl_lookup_vldb(volume->cell, key, idbuf, idsz);
 	if (IS_ERR(vldb)) {
@@ -327,8 +355,7 @@
 	}
 
 	/* See if the volume's server list got updated. */
-	new = afs_alloc_server_list(volume->cell, key,
-				    vldb, (1 << volume->type));
+	new = afs_alloc_server_list(volume, key, vldb);
 	if (IS_ERR(new)) {
 		ret = PTR_ERR(new);
 		goto error_vldb;
@@ -349,9 +376,11 @@
 
 	volume->update_at = ktime_get_real_seconds() + afs_volume_record_life;
 	write_unlock(&volume->servers_lock);
-	ret = 0;
 
+	if (discard == old)
+		afs_reattach_volume_to_servers(volume, new, old);
 	afs_put_serverlist(volume->cell->net, discard);
+	ret = 0;
 error_vldb:
 	kfree(vldb);
 error:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/write.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/write.c
@@ -626,6 +626,7 @@
 	case -EKEYEXPIRED:
 	case -EKEYREJECTED:
 	case -EKEYREVOKED:
+	case -ENETRESET:
 		afs_redirty_pages(wbc, mapping, start, len);
 		mapping_set_error(mapping, ret);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/xdr_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/xdr_fs.h
@@ -88,7 +88,7 @@
 
 	struct {
 		struct afs_xdr_dir_hdr	hdr;
-		u8			alloc_ctrs[AFS_DIR_MAX_BLOCKS];
+		u8			alloc_ctrs[AFS_DIR_BLOCKS_WITH_CTR];
 		__be16			hashtable[AFS_DIR_HASHTBL_SIZE];
 	} meta;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/afs/yfsclient.c
+++ linux-xilinx-zynqmp-5.15.0/fs/afs/yfsclient.c
@@ -239,8 +239,7 @@
 	struct afs_callback *cb = &scb->callback;
 	ktime_t cb_expiry;
 
-	cb_expiry = call->reply_time;
-	cb_expiry = ktime_add(cb_expiry, xdr_to_u64(x->expiration_time) * 100);
+	cb_expiry = ktime_add(call->issue_time, xdr_to_u64(x->expiration_time) * 100);
 	cb->expires_at	= ktime_divns(cb_expiry, NSEC_PER_SEC);
 	scb->have_cb	= true;
 	*_bp += xdr_size(x);
@@ -663,8 +662,9 @@
 static void yfs_done_fs_remove_file2(struct afs_call *call)
 {
 	if (call->error == -ECONNABORTED &&
-	    call->abort_code == RX_INVALID_OPERATION) {
-		set_bit(AFS_SERVER_FL_NO_RM2, &call->server->flags);
+	    (call->abort_code == RX_INVALID_OPERATION ||
+	     call->abort_code == RXGEN_OPCODE)) {
+		set_bit(AFS_SERVER_FL_NO_RM2, &call->op->server->flags);
 		call->op->flags |= AFS_OPERATION_DOWNGRADE;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aio.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aio.c
@@ -181,8 +181,9 @@
 	struct file		*file;
 	struct wait_queue_head	*head;
 	__poll_t		events;
-	bool			done;
 	bool			cancelled;
+	bool			work_scheduled;
+	bool			work_need_resched;
 	struct wait_queue_entry	wait;
 	struct work_struct	work;
 };
@@ -333,6 +334,9 @@
 	spin_lock(&mm->ioctx_lock);
 	rcu_read_lock();
 	table = rcu_dereference(mm->ioctx_table);
+	if (!table)
+		goto out_unlock;
+
 	for (i = 0; i < table->nr; i++) {
 		struct kioctx *ctx;
 
@@ -346,6 +350,7 @@
 		}
 	}
 
+out_unlock:
 	rcu_read_unlock();
 	spin_unlock(&mm->ioctx_lock);
 	return res;
@@ -559,13 +564,24 @@
 
 void kiocb_set_cancel_fn(struct kiocb *iocb, kiocb_cancel_fn *cancel)
 {
-	struct aio_kiocb *req = container_of(iocb, struct aio_kiocb, rw);
-	struct kioctx *ctx = req->ki_ctx;
+	struct aio_kiocb *req;
+	struct kioctx *ctx;
 	unsigned long flags;
 
+	/*
+	 * kiocb didn't come from aio or is neither a read nor a write, hence
+	 * ignore it.
+	 */
+	if (!(iocb->ki_flags & IOCB_AIO_RW))
+		return;
+
+	req = container_of(iocb, struct aio_kiocb, rw);
+
 	if (WARN_ON_ONCE(!list_empty(&req->ki_list)))
 		return;
 
+	ctx = req->ki_ctx;
+
 	spin_lock_irqsave(&ctx->ctx_lock, flags);
 	list_add_tail(&req->ki_list, &ctx->active_reqs);
 	req->ki_cancel = cancel;
@@ -1448,7 +1464,7 @@
 	req->ki_complete = aio_complete_rw;
 	req->private = NULL;
 	req->ki_pos = iocb->aio_offset;
-	req->ki_flags = iocb_flags(req->ki_filp);
+	req->ki_flags = iocb_flags(req->ki_filp) | IOCB_AIO_RW;
 	if (iocb->aio_flags & IOCB_FLAG_RESFD)
 		req->ki_flags |= IOCB_EVENTFD;
 	req->ki_hint = ki_hint_validate(file_write_hint(req->ki_filp));
@@ -1620,6 +1636,51 @@
 	iocb_put(iocb);
 }
 
+/*
+ * Safely lock the waitqueue which the request is on, synchronizing with the
+ * case where the ->poll() provider decides to free its waitqueue early.
+ *
+ * Returns true on success, meaning that req->head->lock was locked, req->wait
+ * is on req->head, and an RCU read lock was taken.  Returns false if the
+ * request was already removed from its waitqueue (which might no longer exist).
+ */
+static bool poll_iocb_lock_wq(struct poll_iocb *req)
+{
+	wait_queue_head_t *head;
+
+	/*
+	 * While we hold the waitqueue lock and the waitqueue is nonempty,
+	 * wake_up_pollfree() will wait for us.  However, taking the waitqueue
+	 * lock in the first place can race with the waitqueue being freed.
+	 *
+	 * We solve this as eventpoll does: by taking advantage of the fact that
+	 * all users of wake_up_pollfree() will RCU-delay the actual free.  If
+	 * we enter rcu_read_lock() and see that the pointer to the queue is
+	 * non-NULL, we can then lock it without the memory being freed out from
+	 * under us, then check whether the request is still on the queue.
+	 *
+	 * Keep holding rcu_read_lock() as long as we hold the queue lock, in
+	 * case the caller deletes the entry from the queue, leaving it empty.
+	 * In that case, only RCU prevents the queue memory from being freed.
+	 */
+	rcu_read_lock();
+	head = smp_load_acquire(&req->head);
+	if (head) {
+		spin_lock(&head->lock);
+		if (!list_empty(&req->wait.entry))
+			return true;
+		spin_unlock(&head->lock);
+	}
+	rcu_read_unlock();
+	return false;
+}
+
+static void poll_iocb_unlock_wq(struct poll_iocb *req)
+{
+	spin_unlock(&req->head->lock);
+	rcu_read_unlock();
+}
+
 static void aio_poll_complete_work(struct work_struct *work)
 {
 	struct poll_iocb *req = container_of(work, struct poll_iocb, work);
@@ -1639,14 +1700,27 @@
 	 * avoid further branches in the fast path.
 	 */
 	spin_lock_irq(&ctx->ctx_lock);
-	if (!mask && !READ_ONCE(req->cancelled)) {
-		add_wait_queue(req->head, &req->wait);
-		spin_unlock_irq(&ctx->ctx_lock);
-		return;
-	}
+	if (poll_iocb_lock_wq(req)) {
+		if (!mask && !READ_ONCE(req->cancelled)) {
+			/*
+			 * The request isn't actually ready to be completed yet.
+			 * Reschedule completion if another wakeup came in.
+			 */
+			if (req->work_need_resched) {
+				schedule_work(&req->work);
+				req->work_need_resched = false;
+			} else {
+				req->work_scheduled = false;
+			}
+			poll_iocb_unlock_wq(req);
+			spin_unlock_irq(&ctx->ctx_lock);
+			return;
+		}
+		list_del_init(&req->wait.entry);
+		poll_iocb_unlock_wq(req);
+	} /* else, POLLFREE has freed the waitqueue, so we must complete */
 	list_del_init(&iocb->ki_list);
 	iocb->ki_res.res = mangle_poll(mask);
-	req->done = true;
 	spin_unlock_irq(&ctx->ctx_lock);
 
 	iocb_put(iocb);
@@ -1658,13 +1732,14 @@
 	struct aio_kiocb *aiocb = container_of(iocb, struct aio_kiocb, rw);
 	struct poll_iocb *req = &aiocb->poll;
 
-	spin_lock(&req->head->lock);
-	WRITE_ONCE(req->cancelled, true);
-	if (!list_empty(&req->wait.entry)) {
-		list_del_init(&req->wait.entry);
-		schedule_work(&aiocb->poll.work);
-	}
-	spin_unlock(&req->head->lock);
+	if (poll_iocb_lock_wq(req)) {
+		WRITE_ONCE(req->cancelled, true);
+		if (!req->work_scheduled) {
+			schedule_work(&aiocb->poll.work);
+			req->work_scheduled = true;
+		}
+		poll_iocb_unlock_wq(req);
+	} /* else, the request was force-cancelled by POLLFREE already */
 
 	return 0;
 }
@@ -1681,21 +1756,27 @@
 	if (mask && !(mask & req->events))
 		return 0;
 
-	list_del_init(&req->wait.entry);
-
-	if (mask && spin_trylock_irqsave(&iocb->ki_ctx->ctx_lock, flags)) {
+	/*
+	 * Complete the request inline if possible.  This requires that three
+	 * conditions be met:
+	 *   1. An event mask must have been passed.  If a plain wakeup was done
+	 *	instead, then mask == 0 and we have to call vfs_poll() to get
+	 *	the events, so inline completion isn't possible.
+	 *   2. The completion work must not have already been scheduled.
+	 *   3. ctx_lock must not be busy.  We have to use trylock because we
+	 *	already hold the waitqueue lock, so this inverts the normal
+	 *	locking order.  Use irqsave/irqrestore because not all
+	 *	filesystems (e.g. fuse) call this function with IRQs disabled,
+	 *	yet IRQs have to be disabled before ctx_lock is obtained.
+	 */
+	if (mask && !req->work_scheduled &&
+	    spin_trylock_irqsave(&iocb->ki_ctx->ctx_lock, flags)) {
 		struct kioctx *ctx = iocb->ki_ctx;
 
-		/*
-		 * Try to complete the iocb inline if we can. Use
-		 * irqsave/irqrestore because not all filesystems (e.g. fuse)
-		 * call this function with IRQs disabled and because IRQs
-		 * have to be disabled before ctx_lock is obtained.
-		 */
+		list_del_init(&req->wait.entry);
 		list_del(&iocb->ki_list);
 		iocb->ki_res.res = mangle_poll(mask);
-		req->done = true;
-		if (iocb->ki_eventfd && eventfd_signal_allowed()) {
+		if (iocb->ki_eventfd && !eventfd_signal_allowed()) {
 			iocb = NULL;
 			INIT_WORK(&req->work, aio_poll_put_work);
 			schedule_work(&req->work);
@@ -1704,7 +1785,43 @@
 		if (iocb)
 			iocb_put(iocb);
 	} else {
-		schedule_work(&req->work);
+		/*
+		 * Schedule the completion work if needed.  If it was already
+		 * scheduled, record that another wakeup came in.
+		 *
+		 * Don't remove the request from the waitqueue here, as it might
+		 * not actually be complete yet (we won't know until vfs_poll()
+		 * is called), and we must not miss any wakeups.  POLLFREE is an
+		 * exception to this; see below.
+		 */
+		if (req->work_scheduled) {
+			req->work_need_resched = true;
+		} else {
+			schedule_work(&req->work);
+			req->work_scheduled = true;
+		}
+
+		/*
+		 * If the waitqueue is being freed early but we can't complete
+		 * the request inline, we have to tear down the request as best
+		 * we can.  That means immediately removing the request from its
+		 * waitqueue and preventing all further accesses to the
+		 * waitqueue via the request.  We also need to schedule the
+		 * completion work (done above).  Also mark the request as
+		 * cancelled, to potentially skip an unneeded call to ->poll().
+		 */
+		if (mask & POLLFREE) {
+			WRITE_ONCE(req->cancelled, true);
+			list_del_init(&req->wait.entry);
+
+			/*
+			 * Careful: this *must* be the last step, since as soon
+			 * as req->head is NULL'ed out, the request can be
+			 * completed and freed, since aio_poll_complete_work()
+			 * will no longer need to take the waitqueue lock.
+			 */
+			smp_store_release(&req->head, NULL);
+		}
 	}
 	return 1;
 }
@@ -1712,6 +1829,7 @@
 struct aio_poll_table {
 	struct poll_table_struct	pt;
 	struct aio_kiocb		*iocb;
+	bool				queued;
 	int				error;
 };
 
@@ -1722,11 +1840,12 @@
 	struct aio_poll_table *pt = container_of(p, struct aio_poll_table, pt);
 
 	/* multiple wait queues per file are not supported */
-	if (unlikely(pt->iocb->poll.head)) {
+	if (unlikely(pt->queued)) {
 		pt->error = -EINVAL;
 		return;
 	}
 
+	pt->queued = true;
 	pt->error = 0;
 	pt->iocb->poll.head = head;
 	add_wait_queue(head, &pt->iocb->poll.wait);
@@ -1751,12 +1870,14 @@
 	req->events = demangle_poll(iocb->aio_buf) | EPOLLERR | EPOLLHUP;
 
 	req->head = NULL;
-	req->done = false;
 	req->cancelled = false;
+	req->work_scheduled = false;
+	req->work_need_resched = false;
 
 	apt.pt._qproc = aio_poll_queue_proc;
 	apt.pt._key = req->events;
 	apt.iocb = aiocb;
+	apt.queued = false;
 	apt.error = -EINVAL; /* same as no support for IOCB_CMD_POLL */
 
 	/* initialized the list so that we can do list_empty checks */
@@ -1765,23 +1886,35 @@
 
 	mask = vfs_poll(req->file, &apt.pt) & req->events;
 	spin_lock_irq(&ctx->ctx_lock);
-	if (likely(req->head)) {
-		spin_lock(&req->head->lock);
-		if (unlikely(list_empty(&req->wait.entry))) {
-			if (apt.error)
+	if (likely(apt.queued)) {
+		bool on_queue = poll_iocb_lock_wq(req);
+
+		if (!on_queue || req->work_scheduled) {
+			/*
+			 * aio_poll_wake() already either scheduled the async
+			 * completion work, or completed the request inline.
+			 */
+			if (apt.error) /* unsupported case: multiple queues */
 				cancel = true;
 			apt.error = 0;
 			mask = 0;
 		}
 		if (mask || apt.error) {
+			/* Steal to complete synchronously. */
 			list_del_init(&req->wait.entry);
 		} else if (cancel) {
+			/* Cancel if possible (may be too late though). */
 			WRITE_ONCE(req->cancelled, true);
-		} else if (!req->done) { /* actually waiting for an event */
+		} else if (on_queue) {
+			/*
+			 * Actually waiting for an event, so add the request to
+			 * active_reqs so that it can be cancelled if needed.
+			 */
 			list_add_tail(&aiocb->ki_list, &ctx->active_reqs);
 			aiocb->ki_cancel = aio_poll_cancel;
 		}
-		spin_unlock(&req->head->lock);
+		if (on_queue)
+			poll_iocb_unlock_wq(req);
 	}
 	if (mask) { /* no async, we'd stolen it */
 		aiocb->ki_res.res = mangle_poll(mask);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/attr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/attr.c
@@ -18,6 +18,71 @@
 #include <linux/evm.h>
 #include <linux/ima.h>
 
+#include "internal.h"
+
+/**
+ * setattr_should_drop_sgid - determine whether the setgid bit needs to be
+ *                            removed
+ * @mnt_userns:	user namespace of the mount @inode was found from
+ * @inode:	inode to check
+ *
+ * This function determines whether the setgid bit needs to be removed.
+ * We retain backwards compatibility and require setgid bit to be removed
+ * unconditionally if S_IXGRP is set. Otherwise we have the exact same
+ * requirements as setattr_prepare() and setattr_copy().
+ *
+ * Return: ATTR_KILL_SGID if setgid bit needs to be removed, 0 otherwise.
+ */
+int setattr_should_drop_sgid(struct user_namespace *mnt_userns,
+			     const struct inode *inode)
+{
+	umode_t mode = inode->i_mode;
+
+	if (!(mode & S_ISGID))
+		return 0;
+	if (mode & S_IXGRP)
+		return ATTR_KILL_SGID;
+	if (!in_group_or_capable(mnt_userns, inode,
+				 i_gid_into_mnt(mnt_userns, inode)))
+		return ATTR_KILL_SGID;
+	return 0;
+}
+EXPORT_SYMBOL(setattr_should_drop_sgid);
+
+/**
+ * setattr_should_drop_suidgid - determine whether the set{g,u}id bit needs to
+ *                               be dropped
+ * @mnt_userns:	user namespace of the mount @inode was found from
+ * @inode:	inode to check
+ *
+ * This function determines whether the set{g,u}id bits need to be removed.
+ * If the setuid bit needs to be removed ATTR_KILL_SUID is returned. If the
+ * setgid bit needs to be removed ATTR_KILL_SGID is returned. If both
+ * set{g,u}id bits need to be removed the corresponding mask of both flags is
+ * returned.
+ *
+ * Return: A mask of ATTR_KILL_S{G,U}ID indicating which - if any - setid bits
+ * to remove, 0 otherwise.
+ */
+int setattr_should_drop_suidgid(struct user_namespace *mnt_userns,
+				struct inode *inode)
+{
+	umode_t mode = inode->i_mode;
+	int kill = 0;
+
+	/* suid always must be killed */
+	if (unlikely(mode & S_ISUID))
+		kill = ATTR_KILL_SUID;
+
+	kill |= setattr_should_drop_sgid(mnt_userns, inode);
+
+	if (unlikely(kill && !capable(CAP_FSETID) && S_ISREG(mode)))
+		return kill;
+
+	return 0;
+}
+EXPORT_SYMBOL(setattr_should_drop_suidgid);
+
 /**
  * chown_ok - verify permissions to chown inode
  * @mnt_userns:	user namespace of the mount @inode was found from
@@ -35,7 +100,7 @@
 		     kuid_t uid)
 {
 	kuid_t kuid = i_uid_into_mnt(mnt_userns, inode);
-	if (uid_eq(current_fsuid(), kuid) && uid_eq(uid, kuid))
+	if (uid_eq(current_fsuid(), kuid) && uid_eq(uid, inode->i_uid))
 		return true;
 	if (capable_wrt_inode_uidgid(mnt_userns, inode, CAP_CHOWN))
 		return true;
@@ -61,9 +126,15 @@
 		     const struct inode *inode, kgid_t gid)
 {
 	kgid_t kgid = i_gid_into_mnt(mnt_userns, inode);
-	if (uid_eq(current_fsuid(), i_uid_into_mnt(mnt_userns, inode)) &&
-	    (in_group_p(gid) || gid_eq(gid, kgid)))
-		return true;
+	if (uid_eq(current_fsuid(), i_uid_into_mnt(mnt_userns, inode))) {
+		kgid_t mapped_gid;
+
+		if (gid_eq(gid, inode->i_gid))
+			return true;
+		mapped_gid = mapped_kgid_fs(mnt_userns, i_user_ns(inode), gid);
+		if (in_group_p(mapped_gid))
+			return true;
+	}
 	if (capable_wrt_inode_uidgid(mnt_userns, inode, CAP_CHOWN))
 		return true;
 	if (gid_eq(kgid, INVALID_GID) &&
@@ -123,12 +194,19 @@
 
 	/* Make sure a caller can chmod. */
 	if (ia_valid & ATTR_MODE) {
+		kgid_t mapped_gid;
+
 		if (!inode_owner_or_capable(mnt_userns, inode))
 			return -EPERM;
+
+		if (ia_valid & ATTR_GID)
+			mapped_gid = mapped_kgid_fs(mnt_userns,
+						i_user_ns(inode), attr->ia_gid);
+		else
+			mapped_gid = i_gid_into_mnt(mnt_userns, inode);
+
 		/* Also check the setgid bit! */
-               if (!in_group_p((ia_valid & ATTR_GID) ? attr->ia_gid :
-                                i_gid_into_mnt(mnt_userns, inode)) &&
-                    !capable_wrt_inode_uidgid(mnt_userns, inode, CAP_FSETID))
+		if (!in_group_or_capable(mnt_userns, inode, mapped_gid))
 			attr->ia_mode &= ~S_ISGID;
 	}
 
@@ -170,6 +248,8 @@
  */
 int inode_newsize_ok(const struct inode *inode, loff_t offset)
 {
+	if (offset < 0)
+		return -EINVAL;
 	if (inode->i_size < offset) {
 		unsigned long limit;
 
@@ -241,8 +321,7 @@
 	if (ia_valid & ATTR_MODE) {
 		umode_t mode = attr->ia_mode;
 		kgid_t kgid = i_gid_into_mnt(mnt_userns, inode);
-		if (!in_group_p(kgid) &&
-		    !capable_wrt_inode_uidgid(mnt_userns, inode, CAP_FSETID))
+		if (!in_group_or_capable(mnt_userns, inode, kgid))
 			mode &= ~S_ISGID;
 		inode->i_mode = mode;
 	}
@@ -323,9 +402,25 @@
 		return error;
 
 	if ((ia_valid & ATTR_MODE)) {
-		umode_t amode = attr->ia_mode;
+		/*
+		 * Don't allow changing the mode of symlinks:
+		 *
+		 * (1) The vfs doesn't take the mode of symlinks into account
+		 *     during permission checking.
+		 * (2) This has never worked correctly. Most major filesystems
+		 *     did return EOPNOTSUPP due to interactions with POSIX ACLs
+		 *     but did still updated the mode of the symlink.
+		 *     This inconsistency led system call wrapper providers such
+		 *     as libc to block changing the mode of symlinks with
+		 *     EOPNOTSUPP already.
+		 * (3) To even do this in the first place one would have to use
+		 *     specific file descriptors and quite some effort.
+		 */
+		if (S_ISLNK(inode->i_mode))
+			return -EOPNOTSUPP;
+
 		/* Flag setting protected by i_mutex */
-		if (is_sxid(amode))
+		if (is_sxid(attr->ia_mode))
 			inode->i_flags &= ~S_NOSEC;
 	}
 
@@ -367,7 +462,7 @@
 		}
 	}
 	if (ia_valid & ATTR_KILL_SGID) {
-		if ((mode & (S_ISGID | S_IXGRP)) == (S_ISGID | S_IXGRP)) {
+		if (mode & S_ISGID) {
 			if (!(ia_valid & ATTR_MODE)) {
 				ia_valid = attr->ia_valid |= ATTR_MODE;
 				attr->ia_mode = inode->i_mode;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/Kconfig
@@ -0,0 +1,199 @@
+# SPDX-License-Identifier: GPL-2.0
+config AUFS_FS
+	tristate "Aufs (Advanced multi layered unification filesystem) support"
+	help
+	Aufs is a stackable unification filesystem such as Unionfs,
+	which unifies several directories and provides a merged single
+	directory.
+	In the early days, aufs was entirely re-designed and
+	re-implemented Unionfs Version 1.x series. Introducing many
+	original ideas, approaches and improvements, it becomes totally
+	different from Unionfs while keeping the basic features.
+
+if AUFS_FS
+choice
+	prompt "Maximum number of branches"
+	default AUFS_BRANCH_MAX_127
+	help
+	Specifies the maximum number of branches (or member directories)
+	in a single aufs. The larger value consumes more system
+	resources and has a minor impact to performance.
+config AUFS_BRANCH_MAX_127
+	bool "127"
+	help
+	Specifies the maximum number of branches (or member directories)
+	in a single aufs. The larger value consumes more system
+	resources and has a minor impact to performance.
+config AUFS_BRANCH_MAX_511
+	bool "511"
+	help
+	Specifies the maximum number of branches (or member directories)
+	in a single aufs. The larger value consumes more system
+	resources and has a minor impact to performance.
+config AUFS_BRANCH_MAX_1023
+	bool "1023"
+	help
+	Specifies the maximum number of branches (or member directories)
+	in a single aufs. The larger value consumes more system
+	resources and has a minor impact to performance.
+config AUFS_BRANCH_MAX_32767
+	bool "32767"
+	help
+	Specifies the maximum number of branches (or member directories)
+	in a single aufs. The larger value consumes more system
+	resources and has a minor impact to performance.
+endchoice
+
+config AUFS_SBILIST
+	bool
+	depends on AUFS_MAGIC_SYSRQ || PROC_FS
+	default y
+	help
+	Automatic configuration for internal use.
+	When aufs supports Magic SysRq or /proc, enabled automatically.
+
+config AUFS_HNOTIFY
+	bool "Detect direct branch access (bypassing aufs)"
+	help
+	If you want to modify files on branches directly, eg. bypassing aufs,
+	and want aufs to detect the changes of them fully, then enable this
+	option and use 'udba=notify' mount option.
+	Currently there is only one available configuration, "fsnotify".
+	It will have a negative impact to the performance.
+	See detail in aufs.5.
+
+choice
+	prompt "method" if AUFS_HNOTIFY
+	default AUFS_HFSNOTIFY
+config AUFS_HFSNOTIFY
+	bool "fsnotify"
+	select FSNOTIFY
+endchoice
+
+config AUFS_EXPORT
+	bool "NFS-exportable aufs"
+	depends on EXPORTFS
+	help
+	If you want to export your mounted aufs via NFS, then enable this
+	option. There are several requirements for this configuration.
+	See detail in aufs.5.
+
+config AUFS_INO_T_64
+	bool
+	depends on AUFS_EXPORT
+	depends on 64BIT
+	default y
+	help
+	Automatic configuration for internal use.
+	/* typedef unsigned long/int __kernel_ino_t */
+	/* alpha and s390x are int */
+
+config AUFS_XATTR
+	bool "support for XATTR/EA (including Security Labels)"
+	help
+	If your branch fs supports XATTR/EA and you want to make them
+	available in aufs too, then enable this opsion and specify the
+	branch attributes for EA.
+	See detail in aufs.5.
+
+config AUFS_FHSM
+	bool "File-based Hierarchical Storage Management"
+	help
+	Hierarchical Storage Management (or HSM) is a well-known feature
+	in the storage world. Aufs provides this feature as file-based.
+	with multiple branches.
+	These multiple branches are prioritized, ie. the topmost one
+	should be the fastest drive and be used heavily.
+
+config AUFS_RDU
+	bool "Readdir in userspace"
+	help
+	Aufs has two methods to provide a merged view for a directory,
+	by a user-space library and by kernel-space natively. The latter
+	is always enabled but sometimes large and slow.
+	If you enable this option, install the library in aufs2-util
+	package, and set some environment variables for your readdir(3),
+	then the work will be handled in user-space which generally
+	shows better performance in most cases.
+	See detail in aufs.5.
+
+config AUFS_DIRREN
+	bool "Workaround for rename(2)-ing a directory"
+	help
+	By default, aufs returns EXDEV error in renameing a dir who has
+	his child on the lower branch, since it is a bad idea to issue
+	rename(2) internally for every lower branch. But user may not
+	accept this behaviour. So here is a workaround to allow such
+	rename(2) and store some extra infromation on the writable
+	branch. Obviously this costs high (and I don't like it).
+	To use this feature, you need to enable this configuration AND
+	to specify the mount option `dirren.'
+	See details in aufs.5 and the design documents.
+
+config AUFS_SHWH
+	bool "Show whiteouts"
+	help
+	If you want to make the whiteouts in aufs visible, then enable
+	this option and specify 'shwh' mount option. Although it may
+	sounds like philosophy or something, but in technically it
+	simply shows the name of whiteout with keeping its behaviour.
+
+config AUFS_BR_RAMFS
+	bool "Ramfs (initramfs/rootfs) as an aufs branch"
+	help
+	If you want to use ramfs as an aufs branch fs, then enable this
+	option. Generally tmpfs is recommended.
+	Aufs prohibited them to be a branch fs by default, because
+	initramfs becomes unusable after switch_root or something
+	generally. If you sets initramfs as an aufs branch and boot your
+	system by switch_root, you will meet a problem easily since the
+	files in initramfs may be inaccessible.
+	Unless you are going to use ramfs as an aufs branch fs without
+	switch_root or something, leave it N.
+
+config AUFS_BR_FUSE
+	bool "Fuse fs as an aufs branch"
+	depends on FUSE_FS
+	select AUFS_POLL
+	help
+	If you want to use fuse-based userspace filesystem as an aufs
+	branch fs, then enable this option.
+	It implements the internal poll(2) operation which is
+	implemented by fuse only (curretnly).
+
+config AUFS_POLL
+	bool
+	help
+	Automatic configuration for internal use.
+
+config AUFS_BR_HFSPLUS
+	bool "Hfsplus as an aufs branch"
+	depends on HFSPLUS_FS
+	default y
+	help
+	If you want to use hfsplus fs as an aufs branch fs, then enable
+	this option. This option introduces a small overhead at
+	copying-up a file on hfsplus.
+
+config AUFS_BDEV_LOOP
+	bool
+	depends on BLK_DEV_LOOP
+	default y
+	help
+	Automatic configuration for internal use.
+	Convert =[ym] into =y.
+
+config AUFS_DEBUG
+	bool "Debug aufs"
+	help
+	Enable this to compile aufs internal debug code.
+	It will have a negative impact to the performance.
+
+config AUFS_MAGIC_SYSRQ
+	bool
+	depends on AUFS_DEBUG && MAGIC_SYSRQ
+	default y
+	help
+	Automatic configuration for internal use.
+	When aufs supports Magic SysRq, enabled automatically.
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/Makefile
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/Makefile
@@ -0,0 +1,46 @@
+# SPDX-License-Identifier: GPL-2.0
+
+include ${src}/magic.mk
+ifeq (${CONFIG_AUFS_FS},m)
+include ${src}/conf.mk
+endif
+-include ${src}/priv_def.mk
+
+# cf. include/linux/kernel.h
+# enable pr_debug
+ccflags-y += -DDEBUG
+# sparse requires the full pathname
+ifdef M
+ccflags-y += -include ${M}/../../include/uapi/linux/aufs_type.h
+else
+ccflags-y += -include ${srctree}/include/uapi/linux/aufs_type.h
+endif
+
+obj-$(CONFIG_AUFS_FS) += aufs.o
+aufs-y := module.o sbinfo.o super.o branch.o xino.o sysaufs.o opts.o \
+	wkq.o vfsub.o dcsub.o \
+	cpup.o whout.o wbr_policy.o \
+	dinfo.o dentry.o \
+	dynop.o \
+	finfo.o file.o f_op.o \
+	dir.o vdir.o \
+	iinfo.o inode.o i_op.o i_op_add.o i_op_del.o i_op_ren.o \
+	mvdown.o ioctl.o
+
+# all are boolean
+aufs-$(CONFIG_PROC_FS) += procfs.o plink.o
+aufs-$(CONFIG_SYSFS) += sysfs.o
+aufs-$(CONFIG_DEBUG_FS) += dbgaufs.o
+aufs-$(CONFIG_AUFS_BDEV_LOOP) += loop.o
+aufs-$(CONFIG_AUFS_HNOTIFY) += hnotify.o
+aufs-$(CONFIG_AUFS_HFSNOTIFY) += hfsnotify.o
+aufs-$(CONFIG_AUFS_EXPORT) += export.o
+aufs-$(CONFIG_AUFS_XATTR) += xattr.o
+aufs-$(CONFIG_FS_POSIX_ACL) += posix_acl.o
+aufs-$(CONFIG_AUFS_DIRREN) += dirren.o
+aufs-$(CONFIG_AUFS_FHSM) += fhsm.o
+aufs-$(CONFIG_AUFS_POLL) += poll.o
+aufs-$(CONFIG_AUFS_RDU) += rdu.o
+aufs-$(CONFIG_AUFS_BR_HFSPLUS) += hfsplus.o
+aufs-$(CONFIG_AUFS_DEBUG) += debug.o
+aufs-$(CONFIG_AUFS_MAGIC_SYSRQ) += sysrq.o
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/aufs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/aufs.h
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * all header files
+ */
+
+#ifndef __AUFS_H__
+#define __AUFS_H__
+
+#ifdef __KERNEL__
+
+#define AuStub(type, name, body, ...) \
+	static inline type name(__VA_ARGS__) { body; }
+
+#define AuStubVoid(name, ...) \
+	AuStub(void, name, , __VA_ARGS__)
+#define AuStubInt0(name, ...) \
+	AuStub(int, name, return 0, __VA_ARGS__)
+
+#include "debug.h"
+
+#include "branch.h"
+#include "cpup.h"
+#include "dcsub.h"
+#include "dbgaufs.h"
+#include "dentry.h"
+#include "dir.h"
+#include "dirren.h"
+#include "dynop.h"
+#include "file.h"
+#include "fstype.h"
+#include "hbl.h"
+#include "inode.h"
+#include "lcnt.h"
+#include "loop.h"
+#include "module.h"
+#include "opts.h"
+#include "rwsem.h"
+#include "super.h"
+#include "sysaufs.h"
+#include "vfsub.h"
+#include "whout.h"
+#include "wkq.h"
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/branch.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/branch.c
@@ -0,0 +1,1427 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * branch management
+ */
+
+#include <linux/compat.h>
+#include <linux/statfs.h>
+#include "aufs.h"
+
+/*
+ * free a single branch
+ */
+static void au_br_do_free(struct au_branch *br)
+{
+	int i;
+	struct au_wbr *wbr;
+	struct au_dykey **key;
+
+	au_hnotify_fin_br(br);
+	/* always, regardless the mount option */
+	au_dr_hino_free(&br->br_dirren);
+	au_xino_put(br);
+
+	AuLCntZero(au_lcnt_read(&br->br_nfiles, /*do_rev*/0));
+	au_lcnt_fin(&br->br_nfiles, /*do_sync*/0);
+	AuLCntZero(au_lcnt_read(&br->br_count, /*do_rev*/0));
+	au_lcnt_fin(&br->br_count, /*do_sync*/0);
+
+	wbr = br->br_wbr;
+	if (wbr) {
+		for (i = 0; i < AuBrWh_Last; i++)
+			dput(wbr->wbr_wh[i]);
+		AuDebugOn(atomic_read(&wbr->wbr_wh_running));
+		AuRwDestroy(&wbr->wbr_wh_rwsem);
+	}
+
+	if (br->br_fhsm) {
+		au_br_fhsm_fin(br->br_fhsm);
+		au_kfree_try_rcu(br->br_fhsm);
+	}
+
+	key = br->br_dykey;
+	for (i = 0; i < AuBrDynOp; i++, key++)
+		if (*key)
+			au_dy_put(*key);
+		else
+			break;
+
+	/* recursive lock, s_umount of branch's */
+	/* synchronize_rcu(); */ /* why? */
+	lockdep_off();
+	path_put(&br->br_path);
+	lockdep_on();
+	au_kfree_rcu(wbr);
+	au_lcnt_wait_for_fin(&br->br_nfiles);
+	au_lcnt_wait_for_fin(&br->br_count);
+	/* I don't know why, but percpu_refcount requires this */
+	/* synchronize_rcu(); */
+	au_kfree_rcu(br);
+}
+
+/*
+ * frees all branches
+ */
+void au_br_free(struct au_sbinfo *sbinfo)
+{
+	aufs_bindex_t bmax;
+	struct au_branch **br;
+
+	AuRwMustWriteLock(&sbinfo->si_rwsem);
+
+	bmax = sbinfo->si_bbot + 1;
+	br = sbinfo->si_branch;
+	while (bmax--)
+		au_br_do_free(*br++);
+}
+
+/*
+ * find the index of a branch which is specified by @br_id.
+ */
+int au_br_index(struct super_block *sb, aufs_bindex_t br_id)
+{
+	aufs_bindex_t bindex, bbot;
+
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++)
+		if (au_sbr_id(sb, bindex) == br_id)
+			return bindex;
+	return -1;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * add a branch
+ */
+
+static int test_overlap(struct super_block *sb, struct dentry *h_adding,
+			struct dentry *h_root)
+{
+	if (unlikely(h_adding == h_root
+		     || au_test_loopback_overlap(sb, h_adding)))
+		return 1;
+	if (h_adding->d_sb != h_root->d_sb)
+		return 0;
+	return au_test_subdir(h_adding, h_root)
+		|| au_test_subdir(h_root, h_adding);
+}
+
+/*
+ * returns a newly allocated branch. @new_nbranch is a number of branches
+ * after adding a branch.
+ */
+static struct au_branch *au_br_alloc(struct super_block *sb, int new_nbranch,
+				     int perm)
+{
+	struct au_branch *add_branch;
+	struct dentry *root;
+	struct inode *inode;
+	int err;
+
+	err = -ENOMEM;
+	add_branch = kzalloc(sizeof(*add_branch), GFP_NOFS);
+	if (unlikely(!add_branch))
+		goto out;
+	add_branch->br_xino = au_xino_alloc(/*nfile*/1);
+	if (unlikely(!add_branch->br_xino))
+		goto out_br;
+	err = au_hnotify_init_br(add_branch, perm);
+	if (unlikely(err))
+		goto out_xino;
+
+	if (au_br_writable(perm)) {
+		/* may be freed separately at changing the branch permission */
+		add_branch->br_wbr = kzalloc(sizeof(*add_branch->br_wbr),
+					     GFP_NOFS);
+		if (unlikely(!add_branch->br_wbr))
+			goto out_hnotify;
+	}
+
+	if (au_br_fhsm(perm)) {
+		err = au_fhsm_br_alloc(add_branch);
+		if (unlikely(err))
+			goto out_wbr;
+	}
+
+	root = sb->s_root;
+	err = au_sbr_realloc(au_sbi(sb), new_nbranch, /*may_shrink*/0);
+	if (!err)
+		err = au_di_realloc(au_di(root), new_nbranch, /*may_shrink*/0);
+	if (!err) {
+		inode = d_inode(root);
+		err = au_hinode_realloc(au_ii(inode), new_nbranch,
+					/*may_shrink*/0);
+	}
+	if (!err)
+		return add_branch; /* success */
+
+out_wbr:
+	au_kfree_rcu(add_branch->br_wbr);
+out_hnotify:
+	au_hnotify_fin_br(add_branch);
+out_xino:
+	au_xino_put(add_branch);
+out_br:
+	au_kfree_rcu(add_branch);
+out:
+	return ERR_PTR(err);
+}
+
+/*
+ * test if the branch permission is legal or not.
+ */
+static int test_br(struct inode *inode, int brperm, char *path)
+{
+	int err;
+
+	err = (au_br_writable(brperm) && IS_RDONLY(inode));
+	if (!err)
+		goto out;
+
+	err = -EINVAL;
+	pr_err("write permission for readonly mount or inode, %s\n", path);
+
+out:
+	return err;
+}
+
+/*
+ * returns:
+ * 0: success, the caller will add it
+ * plus: success, it is already unified, the caller should ignore it
+ * minus: error
+ */
+static int test_add(struct super_block *sb, struct au_opt_add *add, int remount)
+{
+	int err;
+	aufs_bindex_t bbot, bindex;
+	struct dentry *root, *h_dentry;
+	struct inode *inode, *h_inode;
+
+	root = sb->s_root;
+	bbot = au_sbbot(sb);
+	if (unlikely(bbot >= 0
+		     && au_find_dbindex(root, add->path.dentry) >= 0)) {
+		err = 1;
+		if (!remount) {
+			err = -EINVAL;
+			pr_err("%s duplicated\n", add->pathname);
+		}
+		goto out;
+	}
+
+	err = -ENOSPC; /* -E2BIG; */
+	if (unlikely(AUFS_BRANCH_MAX <= add->bindex
+		     || AUFS_BRANCH_MAX - 1 <= bbot)) {
+		pr_err("number of branches exceeded %s\n", add->pathname);
+		goto out;
+	}
+
+	err = -EDOM;
+	if (unlikely(add->bindex < 0 || bbot + 1 < add->bindex)) {
+		pr_err("bad index %d\n", add->bindex);
+		goto out;
+	}
+
+	inode = d_inode(add->path.dentry);
+	err = -ENOENT;
+	if (unlikely(!inode->i_nlink)) {
+		pr_err("no existence %s\n", add->pathname);
+		goto out;
+	}
+
+	err = -EINVAL;
+	if (unlikely(inode->i_sb == sb)) {
+		pr_err("%s must be outside\n", add->pathname);
+		goto out;
+	}
+
+	if (unlikely(au_test_fs_unsuppoted(inode->i_sb))) {
+		pr_err("unsupported filesystem, %s (%s)\n",
+		       add->pathname, au_sbtype(inode->i_sb));
+		goto out;
+	}
+
+	if (unlikely(inode->i_sb->s_stack_depth)) {
+		pr_err("already stacked, %s (%s)\n",
+		       add->pathname, au_sbtype(inode->i_sb));
+		goto out;
+	}
+
+	err = test_br(d_inode(add->path.dentry), add->perm, add->pathname);
+	if (unlikely(err))
+		goto out;
+
+	if (bbot < 0)
+		return 0; /* success */
+
+	err = -EINVAL;
+	for (bindex = 0; bindex <= bbot; bindex++)
+		if (unlikely(test_overlap(sb, add->path.dentry,
+					  au_h_dptr(root, bindex)))) {
+			pr_err("%s is overlapped\n", add->pathname);
+			goto out;
+		}
+
+	err = 0;
+	if (au_opt_test(au_mntflags(sb), WARN_PERM)) {
+		h_dentry = au_h_dptr(root, 0);
+		h_inode = d_inode(h_dentry);
+		if ((h_inode->i_mode & S_IALLUGO) != (inode->i_mode & S_IALLUGO)
+		    || !uid_eq(h_inode->i_uid, inode->i_uid)
+		    || !gid_eq(h_inode->i_gid, inode->i_gid))
+			pr_warn("uid/gid/perm %s %u/%u/0%o, %u/%u/0%o\n",
+				add->pathname,
+				i_uid_read(inode), i_gid_read(inode),
+				(inode->i_mode & S_IALLUGO),
+				i_uid_read(h_inode), i_gid_read(h_inode),
+				(h_inode->i_mode & S_IALLUGO));
+	}
+
+out:
+	return err;
+}
+
+/*
+ * initialize or clean the whiteouts for an adding branch
+ */
+static int au_br_init_wh(struct super_block *sb, struct au_branch *br,
+			 int new_perm)
+{
+	int err, old_perm;
+	aufs_bindex_t bindex;
+	struct inode *h_inode;
+	struct au_wbr *wbr;
+	struct au_hinode *hdir;
+	struct dentry *h_dentry;
+
+	err = vfsub_mnt_want_write(au_br_mnt(br));
+	if (unlikely(err))
+		goto out;
+
+	wbr = br->br_wbr;
+	old_perm = br->br_perm;
+	br->br_perm = new_perm;
+	hdir = NULL;
+	h_inode = NULL;
+	bindex = au_br_index(sb, br->br_id);
+	if (0 <= bindex) {
+		hdir = au_hi(d_inode(sb->s_root), bindex);
+		au_hn_inode_lock_nested(hdir, AuLsc_I_PARENT);
+	} else {
+		h_dentry = au_br_dentry(br);
+		h_inode = d_inode(h_dentry);
+		inode_lock_nested(h_inode, AuLsc_I_PARENT);
+	}
+	if (!wbr)
+		err = au_wh_init(br, sb);
+	else {
+		wbr_wh_write_lock(wbr);
+		err = au_wh_init(br, sb);
+		wbr_wh_write_unlock(wbr);
+	}
+	if (hdir)
+		au_hn_inode_unlock(hdir);
+	else
+		inode_unlock(h_inode);
+	vfsub_mnt_drop_write(au_br_mnt(br));
+	br->br_perm = old_perm;
+
+	if (!err && wbr && !au_br_writable(new_perm)) {
+		au_kfree_rcu(wbr);
+		br->br_wbr = NULL;
+	}
+
+out:
+	return err;
+}
+
+static int au_wbr_init(struct au_branch *br, struct super_block *sb,
+		       int perm)
+{
+	int err;
+	struct kstatfs kst;
+	struct au_wbr *wbr;
+
+	wbr = br->br_wbr;
+	au_rw_init(&wbr->wbr_wh_rwsem);
+	atomic_set(&wbr->wbr_wh_running, 0);
+
+	/*
+	 * a limit for rmdir/rename a dir
+	 * cf. AUFS_MAX_NAMELEN in include/uapi/linux/aufs_type.h
+	 */
+	err = vfs_statfs(&br->br_path, &kst);
+	if (unlikely(err))
+		goto out;
+	err = -EINVAL;
+	if (kst.f_namelen >= NAME_MAX)
+		err = au_br_init_wh(sb, br, perm);
+	else
+		pr_err("%pd(%s), unsupported namelen %ld\n",
+		       au_br_dentry(br),
+		       au_sbtype(au_br_dentry(br)->d_sb), kst.f_namelen);
+
+out:
+	return err;
+}
+
+/* initialize a new branch */
+static int au_br_init(struct au_branch *br, struct super_block *sb,
+		      struct au_opt_add *add)
+{
+	int err;
+	struct au_branch *brbase;
+	struct file *xf;
+	struct inode *h_inode;
+
+	err = 0;
+	br->br_perm = add->perm;
+	br->br_path = add->path; /* set first, path_get() later */
+	spin_lock_init(&br->br_dykey_lock);
+	au_lcnt_init(&br->br_nfiles, /*release*/NULL);
+	au_lcnt_init(&br->br_count, /*release*/NULL);
+	br->br_id = au_new_br_id(sb);
+	AuDebugOn(br->br_id < 0);
+
+	/* always, regardless the given option */
+	err = au_dr_br_init(sb, br, &add->path);
+	if (unlikely(err))
+		goto out_err;
+
+	if (au_br_writable(add->perm)) {
+		err = au_wbr_init(br, sb, add->perm);
+		if (unlikely(err))
+			goto out_err;
+	}
+
+	if (au_opt_test(au_mntflags(sb), XINO)) {
+		brbase = au_sbr(sb, 0);
+		xf = au_xino_file(brbase->br_xino, /*idx*/-1);
+		AuDebugOn(!xf);
+		h_inode = d_inode(add->path.dentry);
+		err = au_xino_init_br(sb, br, h_inode->i_ino, &xf->f_path);
+		if (unlikely(err)) {
+			AuDebugOn(au_xino_file(br->br_xino, /*idx*/-1));
+			goto out_err;
+		}
+	}
+
+	sysaufs_br_init(br);
+	path_get(&br->br_path);
+	goto out; /* success */
+
+out_err:
+	memset(&br->br_path, 0, sizeof(br->br_path));
+out:
+	return err;
+}
+
+static void au_br_do_add_brp(struct au_sbinfo *sbinfo, aufs_bindex_t bindex,
+			     struct au_branch *br, aufs_bindex_t bbot,
+			     aufs_bindex_t amount)
+{
+	struct au_branch **brp;
+
+	AuRwMustWriteLock(&sbinfo->si_rwsem);
+
+	brp = sbinfo->si_branch + bindex;
+	memmove(brp + 1, brp, sizeof(*brp) * amount);
+	*brp = br;
+	sbinfo->si_bbot++;
+	if (unlikely(bbot < 0))
+		sbinfo->si_bbot = 0;
+}
+
+static void au_br_do_add_hdp(struct au_dinfo *dinfo, aufs_bindex_t bindex,
+			     aufs_bindex_t bbot, aufs_bindex_t amount)
+{
+	struct au_hdentry *hdp;
+
+	AuRwMustWriteLock(&dinfo->di_rwsem);
+
+	hdp = au_hdentry(dinfo, bindex);
+	memmove(hdp + 1, hdp, sizeof(*hdp) * amount);
+	au_h_dentry_init(hdp);
+	dinfo->di_bbot++;
+	if (unlikely(bbot < 0))
+		dinfo->di_btop = 0;
+}
+
+static void au_br_do_add_hip(struct au_iinfo *iinfo, aufs_bindex_t bindex,
+			     aufs_bindex_t bbot, aufs_bindex_t amount)
+{
+	struct au_hinode *hip;
+
+	AuRwMustWriteLock(&iinfo->ii_rwsem);
+
+	hip = au_hinode(iinfo, bindex);
+	memmove(hip + 1, hip, sizeof(*hip) * amount);
+	au_hinode_init(hip);
+	iinfo->ii_bbot++;
+	if (unlikely(bbot < 0))
+		iinfo->ii_btop = 0;
+}
+
+static void au_br_do_add(struct super_block *sb, struct au_branch *br,
+			 aufs_bindex_t bindex)
+{
+	struct dentry *root, *h_dentry;
+	struct inode *root_inode, *h_inode;
+	aufs_bindex_t bbot, amount;
+
+	root = sb->s_root;
+	root_inode = d_inode(root);
+	bbot = au_sbbot(sb);
+	amount = bbot + 1 - bindex;
+	h_dentry = au_br_dentry(br);
+	au_sbilist_lock();
+	au_br_do_add_brp(au_sbi(sb), bindex, br, bbot, amount);
+	au_br_do_add_hdp(au_di(root), bindex, bbot, amount);
+	au_br_do_add_hip(au_ii(root_inode), bindex, bbot, amount);
+	au_set_h_dptr(root, bindex, dget(h_dentry));
+	h_inode = d_inode(h_dentry);
+	au_set_h_iptr(root_inode, bindex, au_igrab(h_inode), /*flags*/0);
+	au_sbilist_unlock();
+}
+
+int au_br_add(struct super_block *sb, struct au_opt_add *add, int remount)
+{
+	int err;
+	aufs_bindex_t bbot, add_bindex;
+	struct dentry *root, *h_dentry;
+	struct inode *root_inode;
+	struct au_branch *add_branch;
+
+	root = sb->s_root;
+	root_inode = d_inode(root);
+	IMustLock(root_inode);
+	IiMustWriteLock(root_inode);
+	err = test_add(sb, add, remount);
+	if (unlikely(err < 0))
+		goto out;
+	if (err) {
+		err = 0;
+		goto out; /* success */
+	}
+
+	bbot = au_sbbot(sb);
+	add_branch = au_br_alloc(sb, bbot + 2, add->perm);
+	err = PTR_ERR(add_branch);
+	if (IS_ERR(add_branch))
+		goto out;
+
+	err = au_br_init(add_branch, sb, add);
+	if (unlikely(err)) {
+		au_br_do_free(add_branch);
+		goto out;
+	}
+
+	add_bindex = add->bindex;
+	sysaufs_brs_del(sb, add_bindex);	/* remove successors */
+	au_br_do_add(sb, add_branch, add_bindex);
+	sysaufs_brs_add(sb, add_bindex);	/* append successors */
+	dbgaufs_brs_add(sb, add_bindex, /*topdown*/0);	/* rename successors */
+
+	h_dentry = add->path.dentry;
+	if (!add_bindex) {
+		au_cpup_attr_all(root_inode, /*force*/1);
+		sb->s_maxbytes = h_dentry->d_sb->s_maxbytes;
+	} else
+		au_add_nlink(root_inode, d_inode(h_dentry));
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static unsigned long long au_farray_cb(struct super_block *sb, void *a,
+				       unsigned long long max __maybe_unused,
+				       void *arg)
+{
+	unsigned long long n;
+	struct file **p, *f;
+	struct hlist_bl_head *files;
+	struct hlist_bl_node *pos;
+	struct au_finfo *finfo;
+
+	n = 0;
+	p = a;
+	files = &au_sbi(sb)->si_files;
+	hlist_bl_lock(files);
+	hlist_bl_for_each_entry(finfo, pos, files, fi_hlist) {
+		f = finfo->fi_file;
+		if (file_count(f)
+		    && !special_file(file_inode(f)->i_mode)) {
+			get_file(f);
+			*p++ = f;
+			n++;
+			AuDebugOn(n > max);
+		}
+	}
+	hlist_bl_unlock(files);
+
+	return n;
+}
+
+static struct file **au_farray_alloc(struct super_block *sb,
+				     unsigned long long *max)
+{
+	struct au_sbinfo *sbi;
+
+	sbi = au_sbi(sb);
+	*max = au_lcnt_read(&sbi->si_nfiles, /*do_rev*/1);
+	return au_array_alloc(max, au_farray_cb, sb, /*arg*/NULL);
+}
+
+static void au_farray_free(struct file **a, unsigned long long max)
+{
+	unsigned long long ull;
+
+	for (ull = 0; ull < max; ull++)
+		if (a[ull])
+			fput(a[ull]);
+	kvfree(a);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * delete a branch
+ */
+
+/* to show the line number, do not make it inlined function */
+#define AuVerbose(do_info, fmt, ...) do { \
+	if (do_info) \
+		pr_info(fmt, ##__VA_ARGS__); \
+} while (0)
+
+static int au_test_ibusy(struct inode *inode, aufs_bindex_t btop,
+			 aufs_bindex_t bbot)
+{
+	return (inode && !S_ISDIR(inode->i_mode)) || btop == bbot;
+}
+
+static int au_test_dbusy(struct dentry *dentry, aufs_bindex_t btop,
+			 aufs_bindex_t bbot)
+{
+	return au_test_ibusy(d_inode(dentry), btop, bbot);
+}
+
+/*
+ * test if the branch is deletable or not.
+ */
+static int test_dentry_busy(struct dentry *root, aufs_bindex_t bindex,
+			    unsigned int sigen, const unsigned int verbose)
+{
+	int err, i, j, ndentry;
+	aufs_bindex_t btop, bbot;
+	struct au_dcsub_pages dpages;
+	struct au_dpage *dpage;
+	struct dentry *d;
+
+	err = au_dpages_init(&dpages, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+	err = au_dcsub_pages(&dpages, root, NULL, NULL);
+	if (unlikely(err))
+		goto out_dpages;
+
+	for (i = 0; !err && i < dpages.ndpage; i++) {
+		dpage = dpages.dpages + i;
+		ndentry = dpage->ndentry;
+		for (j = 0; !err && j < ndentry; j++) {
+			d = dpage->dentries[j];
+			AuDebugOn(au_dcount(d) <= 0);
+			if (!au_digen_test(d, sigen)) {
+				di_read_lock_child(d, AuLock_IR);
+				if (unlikely(au_dbrange_test(d))) {
+					di_read_unlock(d, AuLock_IR);
+					continue;
+				}
+			} else {
+				di_write_lock_child(d);
+				if (unlikely(au_dbrange_test(d))) {
+					di_write_unlock(d);
+					continue;
+				}
+				err = au_reval_dpath(d, sigen);
+				if (!err)
+					di_downgrade_lock(d, AuLock_IR);
+				else {
+					di_write_unlock(d);
+					break;
+				}
+			}
+
+			/* AuDbgDentry(d); */
+			btop = au_dbtop(d);
+			bbot = au_dbbot(d);
+			if (btop <= bindex
+			    && bindex <= bbot
+			    && au_h_dptr(d, bindex)
+			    && au_test_dbusy(d, btop, bbot)) {
+				err = -EBUSY;
+				AuVerbose(verbose, "busy %pd\n", d);
+				AuDbgDentry(d);
+			}
+			di_read_unlock(d, AuLock_IR);
+		}
+	}
+
+out_dpages:
+	au_dpages_free(&dpages);
+out:
+	return err;
+}
+
+static int test_inode_busy(struct super_block *sb, aufs_bindex_t bindex,
+			   unsigned int sigen, const unsigned int verbose)
+{
+	int err;
+	unsigned long long max, ull;
+	struct inode *i, **array;
+	aufs_bindex_t btop, bbot;
+
+	array = au_iarray_alloc(sb, &max);
+	err = PTR_ERR(array);
+	if (IS_ERR(array))
+		goto out;
+
+	err = 0;
+	AuDbg("b%d\n", bindex);
+	for (ull = 0; !err && ull < max; ull++) {
+		i = array[ull];
+		if (unlikely(!i))
+			break;
+		if (i->i_ino == AUFS_ROOT_INO)
+			continue;
+
+		/* AuDbgInode(i); */
+		if (au_iigen(i, NULL) == sigen)
+			ii_read_lock_child(i);
+		else {
+			ii_write_lock_child(i);
+			err = au_refresh_hinode_self(i);
+			au_iigen_dec(i);
+			if (!err)
+				ii_downgrade_lock(i);
+			else {
+				ii_write_unlock(i);
+				break;
+			}
+		}
+
+		btop = au_ibtop(i);
+		bbot = au_ibbot(i);
+		if (btop <= bindex
+		    && bindex <= bbot
+		    && au_h_iptr(i, bindex)
+		    && au_test_ibusy(i, btop, bbot)) {
+			err = -EBUSY;
+			AuVerbose(verbose, "busy i%lu\n", i->i_ino);
+			AuDbgInode(i);
+		}
+		ii_read_unlock(i);
+	}
+	au_iarray_free(array, max);
+
+out:
+	return err;
+}
+
+static int test_children_busy(struct dentry *root, aufs_bindex_t bindex,
+			      const unsigned int verbose)
+{
+	int err;
+	unsigned int sigen;
+
+	sigen = au_sigen(root->d_sb);
+	DiMustNoWaiters(root);
+	IiMustNoWaiters(d_inode(root));
+	di_write_unlock(root);
+	err = test_dentry_busy(root, bindex, sigen, verbose);
+	if (!err)
+		err = test_inode_busy(root->d_sb, bindex, sigen, verbose);
+	di_write_lock_child(root); /* aufs_write_lock() calls ..._child() */
+
+	return err;
+}
+
+static int test_dir_busy(struct file *file, aufs_bindex_t br_id,
+			 struct file **to_free, int *idx)
+{
+	int err;
+	unsigned char matched, root;
+	aufs_bindex_t bindex, bbot;
+	struct au_fidir *fidir;
+	struct au_hfile *hfile;
+
+	err = 0;
+	root = IS_ROOT(file->f_path.dentry);
+	if (root) {
+		get_file(file);
+		to_free[*idx] = file;
+		(*idx)++;
+		goto out;
+	}
+
+	matched = 0;
+	fidir = au_fi(file)->fi_hdir;
+	AuDebugOn(!fidir);
+	bbot = au_fbbot_dir(file);
+	for (bindex = au_fbtop(file); bindex <= bbot; bindex++) {
+		hfile = fidir->fd_hfile + bindex;
+		if (!hfile->hf_file)
+			continue;
+
+		if (hfile->hf_br->br_id == br_id) {
+			matched = 1;
+			break;
+		}
+	}
+	if (matched)
+		err = -EBUSY;
+
+out:
+	return err;
+}
+
+static int test_file_busy(struct super_block *sb, aufs_bindex_t br_id,
+			  struct file **to_free, int opened)
+{
+	int err, idx;
+	unsigned long long ull, max;
+	aufs_bindex_t btop;
+	struct file *file, **array;
+	struct dentry *root;
+	struct au_hfile *hfile;
+
+	array = au_farray_alloc(sb, &max);
+	err = PTR_ERR(array);
+	if (IS_ERR(array))
+		goto out;
+
+	err = 0;
+	idx = 0;
+	root = sb->s_root;
+	di_write_unlock(root);
+	for (ull = 0; ull < max; ull++) {
+		file = array[ull];
+		if (unlikely(!file))
+			break;
+
+		/* AuDbg("%pD\n", file); */
+		fi_read_lock(file);
+		btop = au_fbtop(file);
+		if (!d_is_dir(file->f_path.dentry)) {
+			hfile = &au_fi(file)->fi_htop;
+			if (hfile->hf_br->br_id == br_id)
+				err = -EBUSY;
+		} else
+			err = test_dir_busy(file, br_id, to_free, &idx);
+		fi_read_unlock(file);
+		if (unlikely(err))
+			break;
+	}
+	di_write_lock_child(root);
+	au_farray_free(array, max);
+	AuDebugOn(idx > opened);
+
+out:
+	return err;
+}
+
+static void br_del_file(struct file **to_free, unsigned long long opened,
+			aufs_bindex_t br_id)
+{
+	unsigned long long ull;
+	aufs_bindex_t bindex, btop, bbot, bfound;
+	struct file *file;
+	struct au_fidir *fidir;
+	struct au_hfile *hfile;
+
+	for (ull = 0; ull < opened; ull++) {
+		file = to_free[ull];
+		if (unlikely(!file))
+			break;
+
+		/* AuDbg("%pD\n", file); */
+		AuDebugOn(!d_is_dir(file->f_path.dentry));
+		bfound = -1;
+		fidir = au_fi(file)->fi_hdir;
+		AuDebugOn(!fidir);
+		fi_write_lock(file);
+		btop = au_fbtop(file);
+		bbot = au_fbbot_dir(file);
+		for (bindex = btop; bindex <= bbot; bindex++) {
+			hfile = fidir->fd_hfile + bindex;
+			if (!hfile->hf_file)
+				continue;
+
+			if (hfile->hf_br->br_id == br_id) {
+				bfound = bindex;
+				break;
+			}
+		}
+		AuDebugOn(bfound < 0);
+		au_set_h_fptr(file, bfound, NULL);
+		if (bfound == btop) {
+			for (btop++; btop <= bbot; btop++)
+				if (au_hf_dir(file, btop)) {
+					au_set_fbtop(file, btop);
+					break;
+				}
+		}
+		fi_write_unlock(file);
+	}
+}
+
+static void au_br_do_del_brp(struct au_sbinfo *sbinfo,
+			     const aufs_bindex_t bindex,
+			     const aufs_bindex_t bbot)
+{
+	struct au_branch **brp, **p;
+
+	AuRwMustWriteLock(&sbinfo->si_rwsem);
+
+	brp = sbinfo->si_branch + bindex;
+	if (bindex < bbot)
+		memmove(brp, brp + 1, sizeof(*brp) * (bbot - bindex));
+	sbinfo->si_branch[0 + bbot] = NULL;
+	sbinfo->si_bbot--;
+
+	p = au_krealloc(sbinfo->si_branch, sizeof(*p) * bbot, AuGFP_SBILIST,
+			/*may_shrink*/1);
+	if (p)
+		sbinfo->si_branch = p;
+	/* harmless error */
+}
+
+static void au_br_do_del_hdp(struct au_dinfo *dinfo, const aufs_bindex_t bindex,
+			     const aufs_bindex_t bbot)
+{
+	struct au_hdentry *hdp, *p;
+
+	AuRwMustWriteLock(&dinfo->di_rwsem);
+
+	hdp = au_hdentry(dinfo, bindex);
+	if (bindex < bbot)
+		memmove(hdp, hdp + 1, sizeof(*hdp) * (bbot - bindex));
+	/* au_h_dentry_init(au_hdentry(dinfo, bbot); */
+	dinfo->di_bbot--;
+
+	p = au_krealloc(dinfo->di_hdentry, sizeof(*p) * bbot, AuGFP_SBILIST,
+			/*may_shrink*/1);
+	if (p)
+		dinfo->di_hdentry = p;
+	/* harmless error */
+}
+
+static void au_br_do_del_hip(struct au_iinfo *iinfo, const aufs_bindex_t bindex,
+			     const aufs_bindex_t bbot)
+{
+	struct au_hinode *hip, *p;
+
+	AuRwMustWriteLock(&iinfo->ii_rwsem);
+
+	hip = au_hinode(iinfo, bindex);
+	if (bindex < bbot)
+		memmove(hip, hip + 1, sizeof(*hip) * (bbot - bindex));
+	/* au_hinode_init(au_hinode(iinfo, bbot)); */
+	iinfo->ii_bbot--;
+
+	p = au_krealloc(iinfo->ii_hinode, sizeof(*p) * bbot, AuGFP_SBILIST,
+			/*may_shrink*/1);
+	if (p)
+		iinfo->ii_hinode = p;
+	/* harmless error */
+}
+
+static void au_br_do_del(struct super_block *sb, aufs_bindex_t bindex,
+			 struct au_branch *br)
+{
+	aufs_bindex_t bbot;
+	struct au_sbinfo *sbinfo;
+	struct dentry *root, *h_root;
+	struct inode *inode, *h_inode;
+	struct au_hinode *hinode;
+
+	SiMustWriteLock(sb);
+
+	root = sb->s_root;
+	inode = d_inode(root);
+	sbinfo = au_sbi(sb);
+	bbot = sbinfo->si_bbot;
+
+	h_root = au_h_dptr(root, bindex);
+	hinode = au_hi(inode, bindex);
+	h_inode = au_igrab(hinode->hi_inode);
+	au_hiput(hinode);
+
+	au_sbilist_lock();
+	au_br_do_del_brp(sbinfo, bindex, bbot);
+	au_br_do_del_hdp(au_di(root), bindex, bbot);
+	au_br_do_del_hip(au_ii(inode), bindex, bbot);
+	au_sbilist_unlock();
+
+	/* ignore an error */
+	au_dr_br_fin(sb, br); /* always, regardless the mount option */
+
+	dput(h_root);
+	iput(h_inode);
+	au_br_do_free(br);
+}
+
+static unsigned long long empty_cb(struct super_block *sb, void *array,
+				   unsigned long long max, void *arg)
+{
+	return max;
+}
+
+int au_br_del(struct super_block *sb, struct au_opt_del *del, int remount)
+{
+	int err, rerr, i;
+	unsigned long long opened;
+	unsigned int mnt_flags;
+	aufs_bindex_t bindex, bbot, br_id;
+	unsigned char do_wh, verbose;
+	struct au_branch *br;
+	struct au_wbr *wbr;
+	struct dentry *root;
+	struct file **to_free;
+
+	err = 0;
+	opened = 0;
+	to_free = NULL;
+	root = sb->s_root;
+	bindex = au_find_dbindex(root, del->h_path.dentry);
+	if (bindex < 0) {
+		if (remount)
+			goto out; /* success */
+		err = -ENOENT;
+		pr_err("%s no such branch\n", del->pathname);
+		goto out;
+	}
+	AuDbg("bindex b%d\n", bindex);
+
+	err = -EBUSY;
+	mnt_flags = au_mntflags(sb);
+	verbose = !!au_opt_test(mnt_flags, VERBOSE);
+	bbot = au_sbbot(sb);
+	if (unlikely(!bbot)) {
+		AuVerbose(verbose, "no more branches left\n");
+		goto out;
+	}
+
+	br = au_sbr(sb, bindex);
+	AuDebugOn(!path_equal(&br->br_path, &del->h_path));
+	if (unlikely(au_lcnt_read(&br->br_count, /*do_rev*/1))) {
+		AuVerbose(verbose, "br %pd2 is busy now\n", del->h_path.dentry);
+		goto out;
+	}
+
+	br_id = br->br_id;
+	opened = au_lcnt_read(&br->br_nfiles, /*do_rev*/1);
+	if (unlikely(opened)) {
+		to_free = au_array_alloc(&opened, empty_cb, sb, NULL);
+		err = PTR_ERR(to_free);
+		if (IS_ERR(to_free))
+			goto out;
+
+		err = test_file_busy(sb, br_id, to_free, opened);
+		if (unlikely(err)) {
+			AuVerbose(verbose, "%llu file(s) opened\n", opened);
+			goto out;
+		}
+	}
+
+	wbr = br->br_wbr;
+	do_wh = wbr && (wbr->wbr_whbase || wbr->wbr_plink || wbr->wbr_orph);
+	if (do_wh) {
+		/* instead of WbrWhMustWriteLock(wbr) */
+		SiMustWriteLock(sb);
+		for (i = 0; i < AuBrWh_Last; i++) {
+			dput(wbr->wbr_wh[i]);
+			wbr->wbr_wh[i] = NULL;
+		}
+	}
+
+	err = test_children_busy(root, bindex, verbose);
+	if (unlikely(err)) {
+		if (do_wh)
+			goto out_wh;
+		goto out;
+	}
+
+	err = 0;
+	if (to_free) {
+		/*
+		 * now we confirmed the branch is deletable.
+		 * let's free the remaining opened dirs on the branch.
+		 */
+		di_write_unlock(root);
+		br_del_file(to_free, opened, br_id);
+		di_write_lock_child(root);
+	}
+
+	sysaufs_brs_del(sb, bindex);	/* remove successors */
+	dbgaufs_xino_del(br);		/* remove one */
+	au_br_do_del(sb, bindex, br);
+	sysaufs_brs_add(sb, bindex);	/* append successors */
+	dbgaufs_brs_add(sb, bindex, /*topdown*/1);	/* rename successors */
+
+	if (!bindex) {
+		au_cpup_attr_all(d_inode(root), /*force*/1);
+		sb->s_maxbytes = au_sbr_sb(sb, 0)->s_maxbytes;
+	} else
+		au_sub_nlink(d_inode(root), d_inode(del->h_path.dentry));
+	if (au_opt_test(mnt_flags, PLINK))
+		au_plink_half_refresh(sb, br_id);
+
+	goto out; /* success */
+
+out_wh:
+	/* revert */
+	rerr = au_br_init_wh(sb, br, br->br_perm);
+	if (rerr)
+		pr_warn("failed re-creating base whiteout, %s. (%d)\n",
+			del->pathname, rerr);
+out:
+	if (to_free)
+		au_farray_free(to_free, opened);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_ibusy(struct super_block *sb, struct aufs_ibusy __user *arg)
+{
+	int err;
+	aufs_bindex_t btop, bbot;
+	struct aufs_ibusy ibusy;
+	struct inode *inode, *h_inode;
+
+	err = -EPERM;
+	if (unlikely(!capable(CAP_SYS_ADMIN)))
+		goto out;
+
+	err = copy_from_user(&ibusy, arg, sizeof(ibusy));
+	if (!err)
+		/* VERIFY_WRITE */
+		err = !access_ok(&arg->h_ino, sizeof(arg->h_ino));
+	if (unlikely(err)) {
+		err = -EFAULT;
+		AuTraceErr(err);
+		goto out;
+	}
+
+	err = -EINVAL;
+	si_read_lock(sb, AuLock_FLUSH);
+	if (unlikely(ibusy.bindex < 0 || ibusy.bindex > au_sbbot(sb)))
+		goto out_unlock;
+
+	err = 0;
+	ibusy.h_ino = 0; /* invalid */
+	inode = ilookup(sb, ibusy.ino);
+	if (!inode
+	    || inode->i_ino == AUFS_ROOT_INO
+	    || au_is_bad_inode(inode))
+		goto out_unlock;
+
+	ii_read_lock_child(inode);
+	btop = au_ibtop(inode);
+	bbot = au_ibbot(inode);
+	if (btop <= ibusy.bindex && ibusy.bindex <= bbot) {
+		h_inode = au_h_iptr(inode, ibusy.bindex);
+		if (h_inode && au_test_ibusy(inode, btop, bbot))
+			ibusy.h_ino = h_inode->i_ino;
+	}
+	ii_read_unlock(inode);
+	iput(inode);
+
+out_unlock:
+	si_read_unlock(sb);
+	if (!err) {
+		err = __put_user(ibusy.h_ino, &arg->h_ino);
+		if (unlikely(err)) {
+			err = -EFAULT;
+			AuTraceErr(err);
+		}
+	}
+out:
+	return err;
+}
+
+long au_ibusy_ioctl(struct file *file, unsigned long arg)
+{
+	return au_ibusy(file->f_path.dentry->d_sb, (void __user *)arg);
+}
+
+#ifdef CONFIG_COMPAT
+long au_ibusy_compat_ioctl(struct file *file, unsigned long arg)
+{
+	return au_ibusy(file->f_path.dentry->d_sb, compat_ptr(arg));
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * change a branch permission
+ */
+
+static void au_warn_ima(void)
+{
+#ifdef CONFIG_IMA
+	/* since it doesn't support mark_files_ro() */
+	AuWarn1("RW -> RO makes IMA to produce wrong message\n");
+#endif
+}
+
+static int do_need_sigen_inc(int a, int b)
+{
+	return au_br_whable(a) && !au_br_whable(b);
+}
+
+static int need_sigen_inc(int old, int new)
+{
+	return do_need_sigen_inc(old, new)
+		|| do_need_sigen_inc(new, old);
+}
+
+static int au_br_mod_files_ro(struct super_block *sb, aufs_bindex_t bindex)
+{
+	int err, do_warn;
+	unsigned int mnt_flags;
+	unsigned long long ull, max;
+	aufs_bindex_t br_id;
+	unsigned char verbose, writer;
+	struct file *file, *hf, **array;
+	struct au_hfile *hfile;
+	struct inode *h_inode;
+
+	mnt_flags = au_mntflags(sb);
+	verbose = !!au_opt_test(mnt_flags, VERBOSE);
+
+	array = au_farray_alloc(sb, &max);
+	err = PTR_ERR(array);
+	if (IS_ERR(array))
+		goto out;
+
+	do_warn = 0;
+	br_id = au_sbr_id(sb, bindex);
+	for (ull = 0; ull < max; ull++) {
+		file = array[ull];
+		if (unlikely(!file))
+			break;
+
+		/* AuDbg("%pD\n", file); */
+		fi_read_lock(file);
+		if (unlikely(au_test_mmapped(file))) {
+			err = -EBUSY;
+			AuVerbose(verbose, "mmapped %pD\n", file);
+			AuDbgFile(file);
+			FiMustNoWaiters(file);
+			fi_read_unlock(file);
+			goto out_array;
+		}
+
+		hfile = &au_fi(file)->fi_htop;
+		hf = hfile->hf_file;
+		if (!d_is_reg(file->f_path.dentry)
+		    || !(file->f_mode & FMODE_WRITE)
+		    || hfile->hf_br->br_id != br_id
+		    || !(hf->f_mode & FMODE_WRITE))
+			array[ull] = NULL;
+		else {
+			do_warn = 1;
+			get_file(file);
+		}
+
+		FiMustNoWaiters(file);
+		fi_read_unlock(file);
+		fput(file);
+	}
+
+	err = 0;
+	if (do_warn)
+		au_warn_ima();
+
+	for (ull = 0; ull < max; ull++) {
+		file = array[ull];
+		if (!file)
+			continue;
+
+		/* todo: already flushed? */
+		/*
+		 * fs/super.c:mark_files_ro() is gone, but aufs keeps its
+		 * approach which resets f_mode and calls mnt_drop_write() and
+		 * file_release_write() for each file, because the branch
+		 * attribute in aufs world is totally different from the native
+		 * fs rw/ro mode.
+		*/
+		/* fi_read_lock(file); */
+		hfile = &au_fi(file)->fi_htop;
+		hf = hfile->hf_file;
+		/* fi_read_unlock(file); */
+		spin_lock(&hf->f_lock);
+		writer = !!(hf->f_mode & FMODE_WRITER);
+		hf->f_mode &= ~(FMODE_WRITE | FMODE_WRITER);
+		spin_unlock(&hf->f_lock);
+		if (writer) {
+			h_inode = file_inode(hf);
+			if (hf->f_mode & FMODE_READ)
+				i_readcount_inc(h_inode);
+			put_write_access(h_inode);
+			__mnt_drop_write(hf->f_path.mnt);
+		}
+	}
+
+out_array:
+	au_farray_free(array, max);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_br_mod(struct super_block *sb, struct au_opt_mod *mod, int remount,
+	      int *do_refresh)
+{
+	int err, rerr;
+	aufs_bindex_t bindex;
+	struct dentry *root;
+	struct au_branch *br;
+	struct au_br_fhsm *bf;
+
+	root = sb->s_root;
+	bindex = au_find_dbindex(root, mod->h_root);
+	if (bindex < 0) {
+		if (remount)
+			return 0; /* success */
+		err = -ENOENT;
+		pr_err("%s no such branch\n", mod->path);
+		goto out;
+	}
+	AuDbg("bindex b%d\n", bindex);
+
+	err = test_br(d_inode(mod->h_root), mod->perm, mod->path);
+	if (unlikely(err))
+		goto out;
+
+	br = au_sbr(sb, bindex);
+	AuDebugOn(mod->h_root != au_br_dentry(br));
+	if (br->br_perm == mod->perm)
+		return 0; /* success */
+
+	/* pre-allocate for non-fhsm --> fhsm */
+	bf = NULL;
+	if (!au_br_fhsm(br->br_perm) && au_br_fhsm(mod->perm)) {
+		err = au_fhsm_br_alloc(br);
+		if (unlikely(err))
+			goto out;
+		bf = br->br_fhsm;
+		br->br_fhsm = NULL;
+	}
+
+	if (au_br_writable(br->br_perm)) {
+		/* remove whiteout base */
+		err = au_br_init_wh(sb, br, mod->perm);
+		if (unlikely(err))
+			goto out_bf;
+
+		if (!au_br_writable(mod->perm)) {
+			/* rw --> ro, file might be mmapped */
+			DiMustNoWaiters(root);
+			IiMustNoWaiters(d_inode(root));
+			di_write_unlock(root);
+			err = au_br_mod_files_ro(sb, bindex);
+			/* aufs_write_lock() calls ..._child() */
+			di_write_lock_child(root);
+
+			if (unlikely(err)) {
+				rerr = -ENOMEM;
+				br->br_wbr = kzalloc(sizeof(*br->br_wbr),
+						     GFP_NOFS);
+				if (br->br_wbr)
+					rerr = au_wbr_init(br, sb, br->br_perm);
+				if (unlikely(rerr)) {
+					AuIOErr("nested error %d (%d)\n",
+						rerr, err);
+					br->br_perm = mod->perm;
+				}
+			}
+		}
+	} else if (au_br_writable(mod->perm)) {
+		/* ro --> rw */
+		err = -ENOMEM;
+		br->br_wbr = kzalloc(sizeof(*br->br_wbr), GFP_NOFS);
+		if (br->br_wbr) {
+			err = au_wbr_init(br, sb, mod->perm);
+			if (unlikely(err)) {
+				au_kfree_rcu(br->br_wbr);
+				br->br_wbr = NULL;
+			}
+		}
+	}
+	if (unlikely(err))
+		goto out_bf;
+
+	if (au_br_fhsm(br->br_perm)) {
+		if (!au_br_fhsm(mod->perm)) {
+			/* fhsm --> non-fhsm */
+			au_br_fhsm_fin(br->br_fhsm);
+			au_kfree_rcu(br->br_fhsm);
+			br->br_fhsm = NULL;
+		}
+	} else if (au_br_fhsm(mod->perm))
+		/* non-fhsm --> fhsm */
+		br->br_fhsm = bf;
+
+	*do_refresh |= need_sigen_inc(br->br_perm, mod->perm);
+	br->br_perm = mod->perm;
+	goto out; /* success */
+
+out_bf:
+	au_kfree_try_rcu(bf);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_br_stfs(struct au_branch *br, struct aufs_stfs *stfs)
+{
+	int err;
+	struct kstatfs kstfs;
+
+	err = vfs_statfs(&br->br_path, &kstfs);
+	if (!err) {
+		stfs->f_blocks = kstfs.f_blocks;
+		stfs->f_bavail = kstfs.f_bavail;
+		stfs->f_files = kstfs.f_files;
+		stfs->f_ffree = kstfs.f_ffree;
+	}
+
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/branch.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/branch.h
@@ -0,0 +1,375 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * branch filesystems and xino for them
+ */
+
+#ifndef __AUFS_BRANCH_H__
+#define __AUFS_BRANCH_H__
+
+#ifdef __KERNEL__
+
+#include <linux/mount.h>
+#include "dirren.h"
+#include "dynop.h"
+#include "lcnt.h"
+#include "rwsem.h"
+#include "super.h"
+
+/* ---------------------------------------------------------------------- */
+
+/* a xino file */
+struct au_xino {
+	struct file		**xi_file;
+	unsigned int		xi_nfile;
+
+	struct {
+		spinlock_t		spin;
+		ino_t			*array;
+		int			total;
+		/* reserved for future use */
+		/* unsigned long	*bitmap; */
+		wait_queue_head_t	wqh;
+	} xi_nondir;
+
+	struct mutex		xi_mtx;	/* protects xi_file array */
+	struct hlist_bl_head	xi_writing;
+
+	atomic_t		xi_truncating;
+
+	struct kref		xi_kref;
+};
+
+/* File-based Hierarchical Storage Management */
+struct au_br_fhsm {
+#ifdef CONFIG_AUFS_FHSM
+	struct mutex		bf_lock;
+	unsigned long		bf_jiffy;
+	struct aufs_stfs	bf_stfs;
+	int			bf_readable;
+#endif
+};
+
+/* members for writable branch only */
+enum {AuBrWh_BASE, AuBrWh_PLINK, AuBrWh_ORPH, AuBrWh_Last};
+struct au_wbr {
+	struct au_rwsem		wbr_wh_rwsem;
+	struct dentry		*wbr_wh[AuBrWh_Last];
+	atomic_t		wbr_wh_running;
+#define wbr_whbase		wbr_wh[AuBrWh_BASE]	/* whiteout base */
+#define wbr_plink		wbr_wh[AuBrWh_PLINK]	/* pseudo-link dir */
+#define wbr_orph		wbr_wh[AuBrWh_ORPH]	/* dir for orphans */
+
+	/* mfs mode */
+	unsigned long long	wbr_bytes;
+};
+
+/* ext2 has 3 types of operations at least, ext3 has 4 */
+#define AuBrDynOp (AuDyLast * 4)
+
+#ifdef CONFIG_AUFS_HFSNOTIFY
+/* support for asynchronous destruction */
+struct au_br_hfsnotify {
+	struct fsnotify_group	*hfsn_group;
+};
+#endif
+
+/* sysfs entries */
+struct au_brsysfs {
+	char			name[16];
+	struct attribute	attr;
+};
+
+enum {
+	AuBrSysfs_BR,
+	AuBrSysfs_BRID,
+	AuBrSysfs_Last
+};
+
+/* protected by superblock rwsem */
+struct au_branch {
+	struct au_xino		*br_xino;
+
+	aufs_bindex_t		br_id;
+
+	int			br_perm;
+	struct path		br_path;
+	spinlock_t		br_dykey_lock;
+	struct au_dykey		*br_dykey[AuBrDynOp];
+	au_lcnt_t		br_nfiles;	/* opened files */
+	au_lcnt_t		br_count;	/* in-use for other */
+
+	struct au_wbr		*br_wbr;
+	struct au_br_fhsm	*br_fhsm;
+
+#ifdef CONFIG_AUFS_HFSNOTIFY
+	struct au_br_hfsnotify	*br_hfsn;
+#endif
+
+#ifdef CONFIG_SYSFS
+	/* entries under sysfs per mount-point */
+	struct au_brsysfs	br_sysfs[AuBrSysfs_Last];
+#endif
+
+#ifdef CONFIG_DEBUG_FS
+	struct dentry		 *br_dbgaufs; /* xino */
+#endif
+
+	struct au_dr_br		br_dirren;
+};
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct vfsmount *au_br_mnt(struct au_branch *br)
+{
+	return br->br_path.mnt;
+}
+
+static inline struct dentry *au_br_dentry(struct au_branch *br)
+{
+	return br->br_path.dentry;
+}
+
+static inline struct user_namespace *au_br_userns(struct au_branch *br)
+{
+	return mnt_user_ns(br->br_path.mnt);
+}
+
+static inline struct super_block *au_br_sb(struct au_branch *br)
+{
+	return au_br_mnt(br)->mnt_sb;
+}
+
+static inline int au_br_rdonly(struct au_branch *br)
+{
+	return (sb_rdonly(au_br_sb(br))
+		|| !au_br_writable(br->br_perm))
+		? -EROFS : 0;
+}
+
+static inline int au_br_hnotifyable(int brperm __maybe_unused)
+{
+#ifdef CONFIG_AUFS_HNOTIFY
+	return !(brperm & AuBrPerm_RR);
+#else
+	return 0;
+#endif
+}
+
+static inline int au_br_test_oflag(int oflag, struct au_branch *br)
+{
+	int err, exec_flag;
+
+	err = 0;
+	exec_flag = oflag & __FMODE_EXEC;
+	if (unlikely(exec_flag && path_noexec(&br->br_path)))
+		err = -EACCES;
+
+	return err;
+}
+
+static inline void au_xino_get(struct au_branch *br)
+{
+	struct au_xino *xi;
+
+	xi = br->br_xino;
+	if (xi)
+		kref_get(&xi->xi_kref);
+}
+
+static inline int au_xino_count(struct au_branch *br)
+{
+	int v;
+	struct au_xino *xi;
+
+	v = 0;
+	xi = br->br_xino;
+	if (xi)
+		v = kref_read(&xi->xi_kref);
+
+	return v;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* branch.c */
+struct au_sbinfo;
+void au_br_free(struct au_sbinfo *sinfo);
+int au_br_index(struct super_block *sb, aufs_bindex_t br_id);
+struct au_opt_add;
+int au_br_add(struct super_block *sb, struct au_opt_add *add, int remount);
+struct au_opt_del;
+int au_br_del(struct super_block *sb, struct au_opt_del *del, int remount);
+long au_ibusy_ioctl(struct file *file, unsigned long arg);
+#ifdef CONFIG_COMPAT
+long au_ibusy_compat_ioctl(struct file *file, unsigned long arg);
+#endif
+struct au_opt_mod;
+int au_br_mod(struct super_block *sb, struct au_opt_mod *mod, int remount,
+	      int *do_refresh);
+struct aufs_stfs;
+int au_br_stfs(struct au_branch *br, struct aufs_stfs *stfs);
+
+/* xino.c */
+static const loff_t au_loff_max = LLONG_MAX;
+
+aufs_bindex_t au_xi_root(struct super_block *sb, struct dentry *dentry);
+struct file *au_xino_create(struct super_block *sb, char *fpath, int silent,
+			    int wbrtop);
+struct file *au_xino_create2(struct super_block *sb, struct path *base,
+			     struct file *copy_src);
+struct au_xi_new {
+	struct au_xino *xi;	/* switch between xino and xigen */
+	int idx;
+	struct path *base;
+	struct file *copy_src;
+};
+struct file *au_xi_new(struct super_block *sb, struct au_xi_new *xinew);
+
+int au_xino_read(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+		 ino_t *ino);
+int au_xino_write(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+		  ino_t ino);
+ssize_t xino_fread(struct file *file, void *buf, size_t size, loff_t *pos);
+ssize_t xino_fwrite(struct file *file, void *buf, size_t size, loff_t *pos);
+
+int au_xib_trunc(struct super_block *sb);
+int au_xino_trunc(struct super_block *sb, aufs_bindex_t bindex, int idx_begin);
+
+struct au_xino *au_xino_alloc(unsigned int nfile);
+int au_xino_put(struct au_branch *br);
+struct file *au_xino_file1(struct au_xino *xi);
+
+struct au_opt_xino;
+void au_xino_clr(struct super_block *sb);
+int au_xino_set(struct super_block *sb, struct au_opt_xino *xiopt, int remount);
+struct file *au_xino_def(struct super_block *sb);
+int au_xino_init_br(struct super_block *sb, struct au_branch *br, ino_t hino,
+		    struct path *base);
+
+ino_t au_xino_new_ino(struct super_block *sb);
+void au_xino_delete_inode(struct inode *inode, const int unlinked);
+
+void au_xinondir_leave(struct super_block *sb, aufs_bindex_t bindex,
+		       ino_t h_ino, int idx);
+int au_xinondir_enter(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+		      int *idx);
+
+int au_xino_path(struct seq_file *seq, struct file *file);
+
+/* ---------------------------------------------------------------------- */
+
+/* @idx is signed to accept -1 meaning the first file */
+static inline struct file *au_xino_file(struct au_xino *xi, int idx)
+{
+	struct file *file;
+
+	file = NULL;
+	if (!xi)
+		goto out;
+
+	if (idx >= 0) {
+		if (idx < xi->xi_nfile)
+			file = xi->xi_file[idx];
+	} else
+		file = au_xino_file1(xi);
+
+out:
+	return file;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* Superblock to branch */
+static inline
+aufs_bindex_t au_sbr_id(struct super_block *sb, aufs_bindex_t bindex)
+{
+	return au_sbr(sb, bindex)->br_id;
+}
+
+static inline
+struct vfsmount *au_sbr_mnt(struct super_block *sb, aufs_bindex_t bindex)
+{
+	return au_br_mnt(au_sbr(sb, bindex));
+}
+
+static inline
+struct user_namespace *au_sbr_userns(struct super_block *sb, aufs_bindex_t bindex)
+{
+	return au_br_userns(au_sbr(sb, bindex));
+}
+
+static inline
+struct super_block *au_sbr_sb(struct super_block *sb, aufs_bindex_t bindex)
+{
+	return au_br_sb(au_sbr(sb, bindex));
+}
+
+static inline int au_sbr_perm(struct super_block *sb, aufs_bindex_t bindex)
+{
+	return au_sbr(sb, bindex)->br_perm;
+}
+
+static inline int au_sbr_whable(struct super_block *sb, aufs_bindex_t bindex)
+{
+	return au_br_whable(au_sbr_perm(sb, bindex));
+}
+
+/* ---------------------------------------------------------------------- */
+
+#define wbr_wh_read_lock(wbr)	au_rw_read_lock(&(wbr)->wbr_wh_rwsem)
+#define wbr_wh_write_lock(wbr)	au_rw_write_lock(&(wbr)->wbr_wh_rwsem)
+#define wbr_wh_read_trylock(wbr)	au_rw_read_trylock(&(wbr)->wbr_wh_rwsem)
+#define wbr_wh_write_trylock(wbr) au_rw_write_trylock(&(wbr)->wbr_wh_rwsem)
+/*
+#define wbr_wh_read_trylock_nested(wbr) \
+	au_rw_read_trylock_nested(&(wbr)->wbr_wh_rwsem)
+#define wbr_wh_write_trylock_nested(wbr) \
+	au_rw_write_trylock_nested(&(wbr)->wbr_wh_rwsem)
+*/
+
+#define wbr_wh_read_unlock(wbr)	au_rw_read_unlock(&(wbr)->wbr_wh_rwsem)
+#define wbr_wh_write_unlock(wbr)	au_rw_write_unlock(&(wbr)->wbr_wh_rwsem)
+#define wbr_wh_downgrade_lock(wbr)	au_rw_dgrade_lock(&(wbr)->wbr_wh_rwsem)
+
+#define WbrWhMustNoWaiters(wbr)	AuRwMustNoWaiters(&(wbr)->wbr_wh_rwsem)
+#define WbrWhMustAnyLock(wbr)	AuRwMustAnyLock(&(wbr)->wbr_wh_rwsem)
+#define WbrWhMustWriteLock(wbr)	AuRwMustWriteLock(&(wbr)->wbr_wh_rwsem)
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_FHSM
+static inline void au_br_fhsm_init(struct au_br_fhsm *brfhsm)
+{
+	mutex_init(&brfhsm->bf_lock);
+	brfhsm->bf_jiffy = 0;
+	brfhsm->bf_readable = 0;
+}
+
+static inline void au_br_fhsm_fin(struct au_br_fhsm *brfhsm)
+{
+	mutex_destroy(&brfhsm->bf_lock);
+}
+#else
+AuStubVoid(au_br_fhsm_init, struct au_br_fhsm *brfhsm)
+AuStubVoid(au_br_fhsm_fin, struct au_br_fhsm *brfhsm)
+#endif
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_BRANCH_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/conf.mk
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/conf.mk
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: GPL-2.0
+
+AuConfStr = CONFIG_AUFS_FS=${CONFIG_AUFS_FS}
+
+define AuConf
+ifdef ${1}
+AuConfStr += ${1}=${${1}}
+endif
+endef
+
+AuConfAll = BRANCH_MAX_127 BRANCH_MAX_511 BRANCH_MAX_1023 BRANCH_MAX_32767 \
+	SBILIST \
+	HNOTIFY HFSNOTIFY \
+	EXPORT INO_T_64 \
+	XATTR \
+	FHSM \
+	RDU \
+	DIRREN \
+	SHWH \
+	BR_RAMFS \
+	BR_FUSE POLL \
+	BR_HFSPLUS \
+	BDEV_LOOP \
+	DEBUG MAGIC_SYSRQ
+$(foreach i, ${AuConfAll}, \
+	$(eval $(call AuConf,CONFIG_AUFS_${i})))
+
+AuConfName = ${obj}/conf.str
+${AuConfName}.tmp: FORCE
+	@echo ${AuConfStr} | tr ' ' '\n' | sed -e 's/^/"/' -e 's/$$/\\n"/' > $@
+${AuConfName}: ${AuConfName}.tmp
+	@diff -q $< $@ > /dev/null 2>&1 || { \
+	echo '  GEN    ' $@; \
+	cp -p $< $@; \
+	}
+FORCE:
+clean-files += ${AuConfName} ${AuConfName}.tmp
+${obj}/sysfs.o: ${AuConfName}
+
+-include ${srctree}/${src}/conf_priv.mk
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/cpup.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/cpup.c
@@ -0,0 +1,1459 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * copy-up functions, see wbr_policy.c for copy-down
+ */
+
+#include <linux/fs_stack.h>
+#include <linux/mm.h>
+#include <linux/task_work.h>
+#include "aufs.h"
+
+void au_cpup_attr_flags(struct inode *dst, unsigned int iflags)
+{
+	const unsigned int mask = S_DEAD | S_SWAPFILE | S_PRIVATE
+		| S_NOATIME | S_NOCMTIME | S_AUTOMOUNT;
+
+	BUILD_BUG_ON(sizeof(iflags) != sizeof(dst->i_flags));
+
+	dst->i_flags |= iflags & ~mask;
+	if (au_test_fs_notime(dst->i_sb))
+		dst->i_flags |= S_NOATIME | S_NOCMTIME;
+}
+
+void au_cpup_attr_timesizes(struct inode *inode)
+{
+	struct inode *h_inode;
+
+	h_inode = au_h_iptr(inode, au_ibtop(inode));
+	fsstack_copy_attr_times(inode, h_inode);
+	fsstack_copy_inode_size(inode, h_inode);
+}
+
+void au_cpup_attr_nlink(struct inode *inode, int force)
+{
+	struct inode *h_inode;
+	struct super_block *sb;
+	aufs_bindex_t bindex, bbot;
+
+	sb = inode->i_sb;
+	bindex = au_ibtop(inode);
+	h_inode = au_h_iptr(inode, bindex);
+	if (!force
+	    && !S_ISDIR(h_inode->i_mode)
+	    && au_opt_test(au_mntflags(sb), PLINK)
+	    && au_plink_test(inode))
+		return;
+
+	/*
+	 * 0 can happen in revalidating.
+	 * h_inode->i_mutex may not be held here, but it is harmless since once
+	 * i_nlink reaches 0, it will never become positive except O_TMPFILE
+	 * case.
+	 * todo: O_TMPFILE+linkat(AT_SYMLINK_FOLLOW) bypassing aufs may cause
+	 *	 the incorrect link count.
+	 */
+	set_nlink(inode, h_inode->i_nlink);
+
+	/*
+	 * fewer nlink makes find(1) noisy, but larger nlink doesn't.
+	 * it may includes whplink directory.
+	 */
+	if (S_ISDIR(h_inode->i_mode)) {
+		bbot = au_ibbot(inode);
+		for (bindex++; bindex <= bbot; bindex++) {
+			h_inode = au_h_iptr(inode, bindex);
+			if (h_inode)
+				au_add_nlink(inode, h_inode);
+		}
+	}
+}
+
+void au_cpup_attr_changeable(struct inode *inode)
+{
+	struct inode *h_inode;
+
+	h_inode = au_h_iptr(inode, au_ibtop(inode));
+	inode->i_mode = h_inode->i_mode;
+	inode->i_uid = h_inode->i_uid;
+	inode->i_gid = h_inode->i_gid;
+	au_cpup_attr_timesizes(inode);
+	au_cpup_attr_flags(inode, h_inode->i_flags);
+}
+
+void au_cpup_igen(struct inode *inode, struct inode *h_inode)
+{
+	struct au_iinfo *iinfo = au_ii(inode);
+
+	IiMustWriteLock(inode);
+
+	iinfo->ii_higen = h_inode->i_generation;
+	iinfo->ii_hsb1 = h_inode->i_sb;
+}
+
+void au_cpup_attr_all(struct inode *inode, int force)
+{
+	struct inode *h_inode;
+
+	h_inode = au_h_iptr(inode, au_ibtop(inode));
+	au_cpup_attr_changeable(inode);
+	if (inode->i_nlink > 0)
+		au_cpup_attr_nlink(inode, force);
+	inode->i_rdev = h_inode->i_rdev;
+	inode->i_blkbits = h_inode->i_blkbits;
+	au_cpup_igen(inode, h_inode);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* Note: dt_dentry and dt_h_dentry are not dget/dput-ed */
+
+/* keep the timestamps of the parent dir when cpup */
+void au_dtime_store(struct au_dtime *dt, struct dentry *dentry,
+		    struct path *h_path)
+{
+	struct inode *h_inode;
+
+	dt->dt_dentry = dentry;
+	dt->dt_h_path = *h_path;
+	h_inode = d_inode(h_path->dentry);
+	dt->dt_atime = h_inode->i_atime;
+	dt->dt_mtime = h_inode->i_mtime;
+	/* smp_mb(); */
+}
+
+void au_dtime_revert(struct au_dtime *dt)
+{
+	struct iattr attr;
+	int err;
+
+	attr.ia_atime = dt->dt_atime;
+	attr.ia_mtime = dt->dt_mtime;
+	attr.ia_valid = ATTR_FORCE | ATTR_MTIME | ATTR_MTIME_SET
+		| ATTR_ATIME | ATTR_ATIME_SET;
+
+	/* no delegation since this is a directory */
+	err = vfsub_notify_change(&dt->dt_h_path, &attr, /*delegated*/NULL);
+	if (unlikely(err))
+		pr_warn("restoring timestamps failed(%d). ignored\n", err);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* internal use only */
+struct au_cpup_reg_attr {
+	int		valid;
+	struct kstat	st;
+	unsigned int	iflags; /* inode->i_flags */
+};
+
+static noinline_for_stack
+int cpup_iattr(struct dentry *dst, aufs_bindex_t bindex, struct path *h_src,
+	       struct au_cpup_reg_attr *h_src_attr)
+{
+	int err, sbits, icex;
+	unsigned int mnt_flags;
+	unsigned char verbose;
+	struct iattr ia;
+	struct path h_path;
+	struct inode *h_isrc, *h_idst;
+	struct kstat *h_st;
+	struct au_branch *br;
+
+	br = au_sbr(dst->d_sb, bindex);
+	h_path.mnt = au_br_mnt(br);
+	h_path.dentry = au_h_dptr(dst, bindex);
+	h_idst = d_inode(h_path.dentry);
+	h_isrc = d_inode(h_src->dentry);
+	ia.ia_valid = ATTR_FORCE | ATTR_UID | ATTR_GID
+		| ATTR_ATIME | ATTR_MTIME
+		| ATTR_ATIME_SET | ATTR_MTIME_SET;
+	if (h_src_attr && h_src_attr->valid) {
+		h_st = &h_src_attr->st;
+		ia.ia_uid = h_st->uid;
+		ia.ia_gid = h_st->gid;
+		ia.ia_atime = h_st->atime;
+		ia.ia_mtime = h_st->mtime;
+		if (h_idst->i_mode != h_st->mode
+		    && !S_ISLNK(h_idst->i_mode)) {
+			ia.ia_valid |= ATTR_MODE;
+			ia.ia_mode = h_st->mode;
+		}
+		sbits = !!(h_st->mode & (S_ISUID | S_ISGID));
+		au_cpup_attr_flags(h_idst, h_src_attr->iflags);
+	} else {
+		ia.ia_uid = h_isrc->i_uid;
+		ia.ia_gid = h_isrc->i_gid;
+		ia.ia_atime = h_isrc->i_atime;
+		ia.ia_mtime = h_isrc->i_mtime;
+		if (h_idst->i_mode != h_isrc->i_mode
+		    && !S_ISLNK(h_idst->i_mode)) {
+			ia.ia_valid |= ATTR_MODE;
+			ia.ia_mode = h_isrc->i_mode;
+		}
+		sbits = !!(h_isrc->i_mode & (S_ISUID | S_ISGID));
+		au_cpup_attr_flags(h_idst, h_isrc->i_flags);
+	}
+	/* no delegation since it is just created */
+	err = vfsub_notify_change(&h_path, &ia, /*delegated*/NULL);
+
+	/* is this nfs only? */
+	if (!err && sbits && au_test_nfs(h_path.dentry->d_sb)) {
+		ia.ia_valid = ATTR_FORCE | ATTR_MODE;
+		ia.ia_mode = h_isrc->i_mode;
+		err = vfsub_notify_change(&h_path, &ia, /*delegated*/NULL);
+	}
+
+	icex = br->br_perm & AuBrAttr_ICEX;
+	if (!err) {
+		mnt_flags = au_mntflags(dst->d_sb);
+		verbose = !!au_opt_test(mnt_flags, VERBOSE);
+		err = au_cpup_xattr(&h_path, h_src, icex, verbose);
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_do_copy_file(struct file *dst, struct file *src, loff_t len,
+			   char *buf, unsigned long blksize)
+{
+	int err;
+	size_t sz, rbytes, wbytes;
+	unsigned char all_zero;
+	char *p, *zp;
+	struct inode *h_inode;
+	/* reduce stack usage */
+	struct iattr *ia;
+
+	zp = page_address(ZERO_PAGE(0));
+	if (unlikely(!zp))
+		return -ENOMEM; /* possible? */
+
+	err = 0;
+	all_zero = 0;
+	while (len) {
+		AuDbg("len %lld\n", len);
+		sz = blksize;
+		if (len < blksize)
+			sz = len;
+
+		rbytes = 0;
+		/* todo: signal_pending? */
+		while (!rbytes || err == -EAGAIN || err == -EINTR) {
+			rbytes = vfsub_read_k(src, buf, sz, &src->f_pos);
+			err = rbytes;
+		}
+		if (unlikely(err < 0))
+			break;
+
+		all_zero = 0;
+		if (len >= rbytes && rbytes == blksize)
+			all_zero = !memcmp(buf, zp, rbytes);
+		if (!all_zero) {
+			wbytes = rbytes;
+			p = buf;
+			while (wbytes) {
+				size_t b;
+
+				b = vfsub_write_k(dst, p, wbytes, &dst->f_pos);
+				err = b;
+				/* todo: signal_pending? */
+				if (unlikely(err == -EAGAIN || err == -EINTR))
+					continue;
+				if (unlikely(err < 0))
+					break;
+				wbytes -= b;
+				p += b;
+			}
+			if (unlikely(err < 0))
+				break;
+		} else {
+			loff_t res;
+
+			AuLabel(hole);
+			res = vfsub_llseek(dst, rbytes, SEEK_CUR);
+			err = res;
+			if (unlikely(res < 0))
+				break;
+		}
+		len -= rbytes;
+		err = 0;
+	}
+
+	/* the last block may be a hole */
+	if (!err && all_zero) {
+		AuLabel(last hole);
+
+		err = 1;
+		if (au_test_nfs(dst->f_path.dentry->d_sb)) {
+			/* nfs requires this step to make last hole */
+			/* is this only nfs? */
+			do {
+				/* todo: signal_pending? */
+				err = vfsub_write_k(dst, "\0", 1, &dst->f_pos);
+			} while (err == -EAGAIN || err == -EINTR);
+			if (err == 1)
+				dst->f_pos--;
+		}
+
+		if (err == 1) {
+			ia = (void *)buf;
+			ia->ia_size = dst->f_pos;
+			ia->ia_valid = ATTR_SIZE | ATTR_FILE;
+			ia->ia_file = dst;
+			h_inode = file_inode(dst);
+			inode_lock_nested(h_inode, AuLsc_I_CHILD2);
+			/* no delegation since it is just created */
+			err = vfsub_notify_change(&dst->f_path, ia,
+						  /*delegated*/NULL);
+			inode_unlock(h_inode);
+		}
+	}
+
+	return err;
+}
+
+int au_copy_file(struct file *dst, struct file *src, loff_t len)
+{
+	int err;
+	unsigned long blksize;
+	unsigned char do_kfree;
+	char *buf;
+	struct super_block *h_sb;
+
+	err = -ENOMEM;
+	h_sb = file_inode(dst)->i_sb;
+	blksize = h_sb->s_blocksize;
+	if (!blksize || PAGE_SIZE < blksize)
+		blksize = PAGE_SIZE;
+	AuDbg("blksize %lu\n", blksize);
+	do_kfree = (blksize != PAGE_SIZE && blksize >= sizeof(struct iattr *));
+	if (do_kfree)
+		buf = kmalloc(blksize, GFP_NOFS);
+	else
+		buf = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!buf))
+		goto out;
+
+	if (len > (1 << 22))
+		AuDbg("copying a large file %lld\n", (long long)len);
+
+	src->f_pos = 0;
+	dst->f_pos = 0;
+	err = au_do_copy_file(dst, src, len, buf, blksize);
+	if (do_kfree) {
+		AuDebugOn(!au_kfree_do_sz_test(blksize));
+		au_kfree_do_rcu(buf);
+	} else
+		free_page((unsigned long)buf);
+
+out:
+	return err;
+}
+
+static int au_do_copy(struct file *dst, struct file *src, loff_t len)
+{
+	int err;
+	struct super_block *h_src_sb;
+	struct inode *h_src_inode;
+
+	h_src_inode = file_inode(src);
+	h_src_sb = h_src_inode->i_sb;
+
+	/* XFS acquires inode_lock */
+	if (!au_test_xfs(h_src_sb))
+		err = au_copy_file(dst, src, len);
+	else {
+		inode_unlock_shared(h_src_inode);
+		err = au_copy_file(dst, src, len);
+		inode_lock_shared_nested(h_src_inode, AuLsc_I_CHILD);
+	}
+
+	return err;
+}
+
+static int au_clone_or_copy(struct file *dst, struct file *src, loff_t len)
+{
+	int err;
+	loff_t lo;
+	struct super_block *h_src_sb;
+	struct inode *h_src_inode;
+
+	h_src_inode = file_inode(src);
+	h_src_sb = h_src_inode->i_sb;
+	if (h_src_sb != file_inode(dst)->i_sb
+	    || !dst->f_op->remap_file_range) {
+		err = au_do_copy(dst, src, len);
+		goto out;
+	}
+
+	if (!au_test_nfs(h_src_sb)) {
+		inode_unlock_shared(h_src_inode);
+		lo = vfsub_clone_file_range(src, dst, len);
+		inode_lock_shared_nested(h_src_inode, AuLsc_I_CHILD);
+	} else
+		lo = vfsub_clone_file_range(src, dst, len);
+	if (lo == len) {
+		err = 0;
+		goto out; /* success */
+	} else if (lo >= 0)
+		/* todo: possible? */
+		/* paritially succeeded */
+		AuDbg("lo %lld, len %lld. Retrying.\n", lo, len);
+	else if (lo != -EOPNOTSUPP) {
+		/* older XFS has a condition in cloning */
+		err = lo;
+		goto out;
+	}
+
+	/* the backend fs on NFS may not support cloning */
+	err = au_do_copy(dst, src, len);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * to support a sparse file which is opened with O_APPEND,
+ * we need to close the file.
+ */
+static int au_cp_regular(struct au_cp_generic *cpg)
+{
+	int err, i;
+	enum { SRC, DST };
+	struct {
+		aufs_bindex_t bindex;
+		unsigned int flags;
+		struct dentry *dentry;
+		int force_wr;
+		struct file *file;
+	} *f, file[] = {
+		{
+			.bindex = cpg->bsrc,
+			.flags = O_RDONLY | O_NOATIME | O_LARGEFILE,
+		},
+		{
+			.bindex = cpg->bdst,
+			.flags = O_WRONLY | O_NOATIME | O_LARGEFILE,
+			.force_wr = !!au_ftest_cpup(cpg->flags, RWDST),
+		}
+	};
+	struct au_branch *br;
+	struct super_block *sb, *h_src_sb;
+	struct inode *h_src_inode;
+	struct task_struct *tsk = current;
+
+	/* bsrc branch can be ro/rw. */
+	sb = cpg->dentry->d_sb;
+	f = file;
+	for (i = 0; i < 2; i++, f++) {
+		f->dentry = au_h_dptr(cpg->dentry, f->bindex);
+		f->file = au_h_open(cpg->dentry, f->bindex, f->flags,
+				    /*file*/NULL, f->force_wr);
+		if (IS_ERR(f->file)) {
+			err = PTR_ERR(f->file);
+			if (i == SRC)
+				goto out;
+			else
+				goto out_src;
+		}
+	}
+
+	/* try stopping to update while we copyup */
+	h_src_inode = d_inode(file[SRC].dentry);
+	h_src_sb = h_src_inode->i_sb;
+	if (!au_test_nfs(h_src_sb))
+		IMustLock(h_src_inode);
+	err = au_clone_or_copy(file[DST].file, file[SRC].file, cpg->len);
+
+	/* i wonder if we had O_NO_DELAY_FPUT flag */
+	if (tsk->flags & PF_KTHREAD)
+		__fput_sync(file[DST].file);
+	else {
+		/* it happened actually */
+		fput(file[DST].file);
+		/*
+		 * too bad.
+		 * we have to call both since we don't know which place the file
+		 * was added to.
+		 */
+		task_work_run();
+		flush_delayed_fput();
+	}
+	br = au_sbr(sb, file[DST].bindex);
+	au_lcnt_dec(&br->br_nfiles);
+
+out_src:
+	fput(file[SRC].file);
+	br = au_sbr(sb, file[SRC].bindex);
+	au_lcnt_dec(&br->br_nfiles);
+out:
+	return err;
+}
+
+static int au_do_cpup_regular(struct au_cp_generic *cpg,
+			      struct au_cpup_reg_attr *h_src_attr)
+{
+	int err, rerr;
+	loff_t l;
+	struct path h_path;
+	struct inode *h_src_inode, *h_dst_inode;
+
+	err = 0;
+	h_src_inode = au_h_iptr(d_inode(cpg->dentry), cpg->bsrc);
+	l = i_size_read(h_src_inode);
+	if (cpg->len == -1 || l < cpg->len)
+		cpg->len = l;
+	if (cpg->len) {
+		/* try stopping to update while we are referencing */
+		inode_lock_shared_nested(h_src_inode, AuLsc_I_CHILD);
+		au_pin_hdir_unlock(cpg->pin);
+
+		h_path.dentry = au_h_dptr(cpg->dentry, cpg->bsrc);
+		h_path.mnt = au_sbr_mnt(cpg->dentry->d_sb, cpg->bsrc);
+		h_src_attr->iflags = h_src_inode->i_flags;
+		if (!au_test_nfs(h_src_inode->i_sb))
+			err = vfsub_getattr(&h_path, &h_src_attr->st);
+		else {
+			inode_unlock_shared(h_src_inode);
+			err = vfsub_getattr(&h_path, &h_src_attr->st);
+			inode_lock_shared_nested(h_src_inode, AuLsc_I_CHILD);
+		}
+		if (unlikely(err)) {
+			inode_unlock_shared(h_src_inode);
+			goto out;
+		}
+		h_src_attr->valid = 1;
+		if (!au_test_nfs(h_src_inode->i_sb)) {
+			err = au_cp_regular(cpg);
+			inode_unlock_shared(h_src_inode);
+		} else {
+			inode_unlock_shared(h_src_inode);
+			err = au_cp_regular(cpg);
+		}
+		rerr = au_pin_hdir_relock(cpg->pin);
+		if (!err && rerr)
+			err = rerr;
+	}
+	if (!err && (h_src_inode->i_state & I_LINKABLE)) {
+		h_path.dentry = au_h_dptr(cpg->dentry, cpg->bdst);
+		h_dst_inode = d_inode(h_path.dentry);
+		spin_lock(&h_dst_inode->i_lock);
+		h_dst_inode->i_state |= I_LINKABLE;
+		spin_unlock(&h_dst_inode->i_lock);
+	}
+
+out:
+	return err;
+}
+
+static int au_do_cpup_symlink(struct path *h_path, struct dentry *h_src,
+			      struct inode *h_dir)
+{
+	int err;
+	DEFINE_DELAYED_CALL(done);
+	const char *sym;
+
+	sym = vfs_get_link(h_src, &done);
+	err = PTR_ERR(sym);
+	if (IS_ERR(sym))
+		goto out;
+
+	err = vfsub_symlink(h_dir, h_path, sym);
+
+out:
+	do_delayed_call(&done);
+	return err;
+}
+
+/*
+ * regardless 'acl' option, reset all ACL.
+ * All ACL will be copied up later from the original entry on the lower branch.
+ */
+static int au_reset_acl(struct inode *h_dir, struct path *h_path, umode_t mode)
+{
+	int err;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	struct user_namespace *h_userns;
+
+	h_userns = mnt_user_ns(h_path->mnt);
+	h_dentry = h_path->dentry;
+	h_inode = d_inode(h_dentry);
+	/* forget_all_cached_acls(h_inode)); */
+	err = vfsub_removexattr(h_userns, h_dentry, XATTR_NAME_POSIX_ACL_ACCESS);
+	AuTraceErr(err);
+	if (err == -EOPNOTSUPP)
+		err = 0;
+	if (!err)
+		err = vfsub_acl_chmod(h_userns, h_inode, mode);
+
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_do_cpup_dir(struct au_cp_generic *cpg, struct dentry *dst_parent,
+			  struct inode *h_dir, struct path *h_path)
+{
+	int err;
+	struct inode *dir, *inode;
+	struct user_namespace *h_userns;
+
+	h_userns = mnt_user_ns(h_path->mnt);
+	err = vfsub_removexattr(h_userns, h_path->dentry,
+				XATTR_NAME_POSIX_ACL_DEFAULT);
+	AuTraceErr(err);
+	if (err == -EOPNOTSUPP)
+		err = 0;
+	if (unlikely(err))
+		goto out;
+
+	/*
+	 * strange behaviour from the users view,
+	 * particularly setattr case
+	 */
+	dir = d_inode(dst_parent);
+	if (au_ibtop(dir) == cpg->bdst)
+		au_cpup_attr_nlink(dir, /*force*/1);
+	inode = d_inode(cpg->dentry);
+	au_cpup_attr_nlink(inode, /*force*/1);
+
+out:
+	return err;
+}
+
+static noinline_for_stack
+int cpup_entry(struct au_cp_generic *cpg, struct dentry *dst_parent,
+	       struct au_cpup_reg_attr *h_src_attr)
+{
+	int err;
+	umode_t mode;
+	unsigned int mnt_flags;
+	unsigned char isdir, isreg, force;
+	const unsigned char do_dt = !!au_ftest_cpup(cpg->flags, DTIME);
+	struct au_dtime dt;
+	struct path h_path;
+	struct dentry *h_src, *h_dst, *h_parent;
+	struct inode *h_inode, *h_dir;
+	struct super_block *sb;
+
+	/* bsrc branch can be ro/rw. */
+	h_src = au_h_dptr(cpg->dentry, cpg->bsrc);
+	h_inode = d_inode(h_src);
+	AuDebugOn(h_inode != au_h_iptr(d_inode(cpg->dentry), cpg->bsrc));
+
+	/* try stopping to be referenced while we are creating */
+	h_dst = au_h_dptr(cpg->dentry, cpg->bdst);
+	if (au_ftest_cpup(cpg->flags, RENAME))
+		AuDebugOn(strncmp(h_dst->d_name.name, AUFS_WH_PFX,
+				  AUFS_WH_PFX_LEN));
+	h_parent = h_dst->d_parent; /* dir inode is locked */
+	h_dir = d_inode(h_parent);
+	IMustLock(h_dir);
+	AuDebugOn(h_parent != h_dst->d_parent);
+
+	sb = cpg->dentry->d_sb;
+	h_path.mnt = au_sbr_mnt(sb, cpg->bdst);
+	if (do_dt) {
+		h_path.dentry = h_parent;
+		au_dtime_store(&dt, dst_parent, &h_path);
+	}
+	h_path.dentry = h_dst;
+
+	isreg = 0;
+	isdir = 0;
+	mode = h_inode->i_mode;
+	switch (mode & S_IFMT) {
+	case S_IFREG:
+		isreg = 1;
+		err = vfsub_create(h_dir, &h_path, 0600, /*want_excl*/true);
+		if (!err)
+			err = au_do_cpup_regular(cpg, h_src_attr);
+		break;
+	case S_IFDIR:
+		isdir = 1;
+		err = vfsub_mkdir(h_dir, &h_path, mode);
+		if (!err)
+			err = au_do_cpup_dir(cpg, dst_parent, h_dir, &h_path);
+		break;
+	case S_IFLNK:
+		err = au_do_cpup_symlink(&h_path, h_src, h_dir);
+		break;
+	case S_IFCHR:
+	case S_IFBLK:
+		AuDebugOn(!capable(CAP_MKNOD));
+		fallthrough;
+	case S_IFIFO:
+	case S_IFSOCK:
+		err = vfsub_mknod(h_dir, &h_path, mode, h_inode->i_rdev);
+		break;
+	default:
+		AuIOErr("Unknown inode type 0%o\n", mode);
+		err = -EIO;
+	}
+	if (!err)
+		err = au_reset_acl(h_dir, &h_path, mode);
+
+	mnt_flags = au_mntflags(sb);
+	if (!au_opt_test(mnt_flags, UDBA_NONE)
+	    && !isdir
+	    && au_opt_test(mnt_flags, XINO)
+	    && (h_inode->i_nlink == 1
+		|| (h_inode->i_state & I_LINKABLE))
+	    /* todo: unnecessary? */
+	    /* && d_inode(cpg->dentry)->i_nlink == 1 */
+	    && cpg->bdst < cpg->bsrc
+	    && !au_ftest_cpup(cpg->flags, KEEPLINO))
+		au_xino_write(sb, cpg->bsrc, h_inode->i_ino, /*ino*/0);
+		/* ignore this error */
+
+	if (!err) {
+		force = 0;
+		if (isreg) {
+			force = !!cpg->len;
+			if (cpg->len == -1)
+				force = !!i_size_read(h_inode);
+		}
+		au_fhsm_wrote(sb, cpg->bdst, force);
+	}
+
+	if (do_dt)
+		au_dtime_revert(&dt);
+	return err;
+}
+
+static int au_do_ren_after_cpup(struct au_cp_generic *cpg, struct path *h_path)
+{
+	int err;
+	struct dentry *dentry, *h_dentry, *h_parent, *parent;
+	struct path h_ppath;
+	struct inode *h_dir;
+	aufs_bindex_t bdst;
+
+	dentry = cpg->dentry;
+	bdst = cpg->bdst;
+	h_ppath.mnt = au_sbr_mnt(dentry->d_sb, bdst);
+	h_dentry = au_h_dptr(dentry, bdst);
+	if (!au_ftest_cpup(cpg->flags, OVERWRITE)) {
+		dget(h_dentry);
+		au_set_h_dptr(dentry, bdst, NULL);
+		err = au_lkup_neg(dentry, bdst, /*wh*/0);
+		if (!err)
+			h_path->dentry = dget(au_h_dptr(dentry, bdst));
+		au_set_h_dptr(dentry, bdst, h_dentry);
+	} else {
+		err = 0;
+		parent = dget_parent(dentry);
+		h_ppath.dentry = au_h_dptr(parent, bdst);
+		dput(parent);
+		h_path->dentry = vfsub_lkup_one(&dentry->d_name, &h_ppath);
+		if (IS_ERR(h_path->dentry))
+			err = PTR_ERR(h_path->dentry);
+	}
+	if (unlikely(err))
+		goto out;
+
+	h_parent = h_dentry->d_parent; /* dir inode is locked */
+	h_dir = d_inode(h_parent);
+	IMustLock(h_dir);
+	AuDbg("%pd %pd\n", h_dentry, h_path->dentry);
+	/* no delegation since it is just created */
+	err = vfsub_rename(h_dir, h_dentry, h_dir, h_path, /*delegated*/NULL,
+			   /*flags*/0);
+	dput(h_path->dentry);
+
+out:
+	return err;
+}
+
+/*
+ * copyup the @dentry from @bsrc to @bdst.
+ * the caller must set the both of lower dentries.
+ * @len is for truncating when it is -1 copyup the entire file.
+ * in link/rename cases, @dst_parent may be different from the real one.
+ * basic->bsrc can be larger than basic->bdst.
+ * aufs doesn't touch the credential so
+ * security_inode_copy_up{,_xattr}() are unnecessary.
+ */
+static int au_cpup_single(struct au_cp_generic *cpg, struct dentry *dst_parent)
+{
+	int err, rerr;
+	aufs_bindex_t old_ibtop;
+	unsigned char isdir, plink;
+	struct dentry *h_src, *h_dst, *h_parent;
+	struct inode *dst_inode, *h_dir, *inode, *delegated, *src_inode;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct path h_src_path;
+	/* to reduce stack size */
+	struct {
+		struct au_dtime dt;
+		struct path h_path;
+		struct au_cpup_reg_attr h_src_attr;
+	} *a;
+
+	err = -ENOMEM;
+	a = kmalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+	a->h_src_attr.valid = 0;
+
+	sb = cpg->dentry->d_sb;
+	br = au_sbr(sb, cpg->bdst);
+	a->h_path.mnt = au_br_mnt(br);
+	h_dst = au_h_dptr(cpg->dentry, cpg->bdst);
+	h_parent = h_dst->d_parent; /* dir inode is locked */
+	h_dir = d_inode(h_parent);
+	IMustLock(h_dir);
+
+	h_src = au_h_dptr(cpg->dentry, cpg->bsrc);
+	inode = d_inode(cpg->dentry);
+
+	if (!dst_parent)
+		dst_parent = dget_parent(cpg->dentry);
+	else
+		dget(dst_parent);
+
+	plink = !!au_opt_test(au_mntflags(sb), PLINK);
+	dst_inode = au_h_iptr(inode, cpg->bdst);
+	if (dst_inode) {
+		if (unlikely(!plink)) {
+			err = -EIO;
+			AuIOErr("hi%lu(i%lu) exists on b%d "
+				"but plink is disabled\n",
+				dst_inode->i_ino, inode->i_ino, cpg->bdst);
+			goto out_parent;
+		}
+
+		if (dst_inode->i_nlink) {
+			const int do_dt = au_ftest_cpup(cpg->flags, DTIME);
+
+			h_src = au_plink_lkup(inode, cpg->bdst);
+			err = PTR_ERR(h_src);
+			if (IS_ERR(h_src))
+				goto out_parent;
+			if (unlikely(d_is_negative(h_src))) {
+				err = -EIO;
+				AuIOErr("i%lu exists on b%d "
+					"but not pseudo-linked\n",
+					inode->i_ino, cpg->bdst);
+				dput(h_src);
+				goto out_parent;
+			}
+
+			if (do_dt) {
+				a->h_path.dentry = h_parent;
+				au_dtime_store(&a->dt, dst_parent, &a->h_path);
+			}
+
+			a->h_path.dentry = h_dst;
+			delegated = NULL;
+			err = vfsub_link(h_src, h_dir, &a->h_path, &delegated);
+			if (!err && au_ftest_cpup(cpg->flags, RENAME))
+				err = au_do_ren_after_cpup(cpg, &a->h_path);
+			if (do_dt)
+				au_dtime_revert(&a->dt);
+			if (unlikely(err == -EWOULDBLOCK)) {
+				pr_warn("cannot retry for NFSv4 delegation"
+					" for an internal link\n");
+				iput(delegated);
+			}
+			dput(h_src);
+			goto out_parent;
+		} else
+			/* todo: cpup_wh_file? */
+			/* udba work */
+			au_update_ibrange(inode, /*do_put_zero*/1);
+	}
+
+	isdir = S_ISDIR(inode->i_mode);
+	old_ibtop = au_ibtop(inode);
+	err = cpup_entry(cpg, dst_parent, &a->h_src_attr);
+	if (unlikely(err))
+		goto out_rev;
+	dst_inode = d_inode(h_dst);
+	inode_lock_nested(dst_inode, AuLsc_I_CHILD2);
+	/* todo: necessary? */
+	/* au_pin_hdir_unlock(cpg->pin); */
+
+	h_src_path.dentry = h_src;
+	h_src_path.mnt = au_sbr_mnt(sb, cpg->bsrc);
+	err = cpup_iattr(cpg->dentry, cpg->bdst, &h_src_path, &a->h_src_attr);
+	if (unlikely(err)) {
+		/* todo: necessary? */
+		/* au_pin_hdir_relock(cpg->pin); */ /* ignore an error */
+		inode_unlock(dst_inode);
+		goto out_rev;
+	}
+
+	if (cpg->bdst < old_ibtop) {
+		if (S_ISREG(inode->i_mode)) {
+			err = au_dy_iaop(inode, cpg->bdst, dst_inode);
+			if (unlikely(err)) {
+				/* ignore an error */
+				/* au_pin_hdir_relock(cpg->pin); */
+				inode_unlock(dst_inode);
+				goto out_rev;
+			}
+		}
+		au_set_ibtop(inode, cpg->bdst);
+	} else
+		au_set_ibbot(inode, cpg->bdst);
+	au_set_h_iptr(inode, cpg->bdst, au_igrab(dst_inode),
+		      au_hi_flags(inode, isdir));
+
+	/* todo: necessary? */
+	/* err = au_pin_hdir_relock(cpg->pin); */
+	inode_unlock(dst_inode);
+	if (unlikely(err))
+		goto out_rev;
+
+	src_inode = d_inode(h_src);
+	if (!isdir
+	    && (src_inode->i_nlink > 1
+		|| src_inode->i_state & I_LINKABLE)
+	    && plink)
+		au_plink_append(inode, cpg->bdst, h_dst);
+
+	if (au_ftest_cpup(cpg->flags, RENAME)) {
+		a->h_path.dentry = h_dst;
+		err = au_do_ren_after_cpup(cpg, &a->h_path);
+	}
+	if (!err)
+		goto out_parent; /* success */
+
+	/* revert */
+out_rev:
+	a->h_path.dentry = h_parent;
+	au_dtime_store(&a->dt, dst_parent, &a->h_path);
+	a->h_path.dentry = h_dst;
+	rerr = 0;
+	if (d_is_positive(h_dst)) {
+		if (!isdir) {
+			/* no delegation since it is just created */
+			rerr = vfsub_unlink(h_dir, &a->h_path,
+					    /*delegated*/NULL, /*force*/0);
+		} else
+			rerr = vfsub_rmdir(h_dir, &a->h_path);
+	}
+	au_dtime_revert(&a->dt);
+	if (rerr) {
+		AuIOErr("failed removing broken entry(%d, %d)\n", err, rerr);
+		err = -EIO;
+	}
+out_parent:
+	dput(dst_parent);
+	au_kfree_rcu(a);
+out:
+	return err;
+}
+
+#if 0 /* reserved */
+struct au_cpup_single_args {
+	int *errp;
+	struct au_cp_generic *cpg;
+	struct dentry *dst_parent;
+};
+
+static void au_call_cpup_single(void *args)
+{
+	struct au_cpup_single_args *a = args;
+
+	au_pin_hdir_acquire_nest(a->cpg->pin);
+	*a->errp = au_cpup_single(a->cpg, a->dst_parent);
+	au_pin_hdir_release(a->cpg->pin);
+}
+#endif
+
+/*
+ * prevent SIGXFSZ in copy-up.
+ * testing CAP_MKNOD is for generic fs,
+ * but CAP_FSETID is for xfs only, currently.
+ */
+static int au_cpup_sio_test(struct au_pin *pin, umode_t mode)
+{
+	int do_sio;
+	struct super_block *sb;
+	struct inode *h_dir;
+
+	do_sio = 0;
+	sb = au_pinned_parent(pin)->d_sb;
+	if (!au_wkq_test()
+	    && (!au_sbi(sb)->si_plink_maint_pid
+		|| au_plink_maint(sb, AuLock_NOPLM))) {
+		switch (mode & S_IFMT) {
+		case S_IFREG:
+			/* no condition about RLIMIT_FSIZE and the file size */
+			do_sio = 1;
+			break;
+		case S_IFCHR:
+		case S_IFBLK:
+			do_sio = !capable(CAP_MKNOD);
+			break;
+		}
+		if (!do_sio)
+			do_sio = ((mode & (S_ISUID | S_ISGID))
+				  && !capable(CAP_FSETID));
+		/* this workaround may be removed in the future */
+		if (!do_sio) {
+			h_dir = au_pinned_h_dir(pin);
+			do_sio = h_dir->i_mode & S_ISVTX;
+		}
+	}
+
+	return do_sio;
+}
+
+#if 0 /* reserved */
+int au_sio_cpup_single(struct au_cp_generic *cpg, struct dentry *dst_parent)
+{
+	int err, wkq_err;
+	struct dentry *h_dentry;
+
+	h_dentry = au_h_dptr(cpg->dentry, cpg->bsrc);
+	if (!au_cpup_sio_test(pin, d_inode(h_dentry)->i_mode))
+		err = au_cpup_single(cpg, dst_parent);
+	else {
+		struct au_cpup_single_args args = {
+			.errp		= &err,
+			.cpg		= cpg,
+			.dst_parent	= dst_parent
+		};
+		wkq_err = au_wkq_wait(au_call_cpup_single, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+
+	return err;
+}
+#endif
+
+/*
+ * copyup the @dentry from the first active lower branch to @bdst,
+ * using au_cpup_single().
+ */
+static int au_cpup_simple(struct au_cp_generic *cpg)
+{
+	int err;
+	unsigned int flags_orig;
+	struct dentry *dentry;
+
+	AuDebugOn(cpg->bsrc < 0);
+
+	dentry = cpg->dentry;
+	DiMustWriteLock(dentry);
+
+	err = au_lkup_neg(dentry, cpg->bdst, /*wh*/1);
+	if (!err) {
+		flags_orig = cpg->flags;
+		au_fset_cpup(cpg->flags, RENAME);
+		err = au_cpup_single(cpg, NULL);
+		cpg->flags = flags_orig;
+		if (!err)
+			return 0; /* success */
+
+		/* revert */
+		au_set_h_dptr(dentry, cpg->bdst, NULL);
+		au_set_dbtop(dentry, cpg->bsrc);
+	}
+
+	return err;
+}
+
+struct au_cpup_simple_args {
+	int *errp;
+	struct au_cp_generic *cpg;
+};
+
+static void au_call_cpup_simple(void *args)
+{
+	struct au_cpup_simple_args *a = args;
+
+	au_pin_hdir_acquire_nest(a->cpg->pin);
+	*a->errp = au_cpup_simple(a->cpg);
+	au_pin_hdir_release(a->cpg->pin);
+}
+
+static int au_do_sio_cpup_simple(struct au_cp_generic *cpg)
+{
+	int err, wkq_err;
+	struct dentry *dentry, *parent;
+	struct file *h_file;
+	struct inode *h_dir;
+	struct user_namespace *h_userns;
+
+	dentry = cpg->dentry;
+	h_file = NULL;
+	if (au_ftest_cpup(cpg->flags, HOPEN)) {
+		AuDebugOn(cpg->bsrc < 0);
+		h_file = au_h_open_pre(dentry, cpg->bsrc, /*force_wr*/0);
+		err = PTR_ERR(h_file);
+		if (IS_ERR(h_file))
+			goto out;
+	}
+
+	parent = dget_parent(dentry);
+	h_dir = au_h_iptr(d_inode(parent), cpg->bdst);
+	h_userns = au_sbr_userns(dentry->d_sb, cpg->bdst);
+	if (!au_test_h_perm_sio(h_userns, h_dir, MAY_EXEC | MAY_WRITE)
+	    && !au_cpup_sio_test(cpg->pin, d_inode(dentry)->i_mode))
+		err = au_cpup_simple(cpg);
+	else {
+		struct au_cpup_simple_args args = {
+			.errp		= &err,
+			.cpg		= cpg
+		};
+		wkq_err = au_wkq_wait(au_call_cpup_simple, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+
+	dput(parent);
+	if (h_file)
+		au_h_open_post(dentry, cpg->bsrc, h_file);
+
+out:
+	return err;
+}
+
+int au_sio_cpup_simple(struct au_cp_generic *cpg)
+{
+	aufs_bindex_t bsrc, bbot;
+	struct dentry *dentry, *h_dentry;
+
+	if (cpg->bsrc < 0) {
+		dentry = cpg->dentry;
+		bbot = au_dbbot(dentry);
+		for (bsrc = cpg->bdst + 1; bsrc <= bbot; bsrc++) {
+			h_dentry = au_h_dptr(dentry, bsrc);
+			if (h_dentry) {
+				AuDebugOn(d_is_negative(h_dentry));
+				break;
+			}
+		}
+		AuDebugOn(bsrc > bbot);
+		cpg->bsrc = bsrc;
+	}
+	AuDebugOn(cpg->bsrc <= cpg->bdst);
+	return au_do_sio_cpup_simple(cpg);
+}
+
+int au_sio_cpdown_simple(struct au_cp_generic *cpg)
+{
+	AuDebugOn(cpg->bdst <= cpg->bsrc);
+	return au_do_sio_cpup_simple(cpg);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * copyup the deleted file for writing.
+ */
+static int au_do_cpup_wh(struct au_cp_generic *cpg, struct dentry *wh_dentry,
+			 struct file *file)
+{
+	int err;
+	unsigned int flags_orig;
+	aufs_bindex_t bsrc_orig;
+	struct au_dinfo *dinfo;
+	struct {
+		struct au_hdentry *hd;
+		struct dentry *h_dentry;
+	} hdst, hsrc;
+
+	dinfo = au_di(cpg->dentry);
+	AuRwMustWriteLock(&dinfo->di_rwsem);
+
+	bsrc_orig = cpg->bsrc;
+	cpg->bsrc = dinfo->di_btop;
+	hdst.hd = au_hdentry(dinfo, cpg->bdst);
+	hdst.h_dentry = hdst.hd->hd_dentry;
+	hdst.hd->hd_dentry = wh_dentry;
+	dinfo->di_btop = cpg->bdst;
+
+	hsrc.h_dentry = NULL;
+	if (file) {
+		hsrc.hd = au_hdentry(dinfo, cpg->bsrc);
+		hsrc.h_dentry = hsrc.hd->hd_dentry;
+		hsrc.hd->hd_dentry = au_hf_top(file)->f_path.dentry;
+	}
+	flags_orig = cpg->flags;
+	cpg->flags = !AuCpup_DTIME;
+	err = au_cpup_single(cpg, /*h_parent*/NULL);
+	cpg->flags = flags_orig;
+	if (file) {
+		if (!err)
+			err = au_reopen_nondir(file);
+		hsrc.hd->hd_dentry = hsrc.h_dentry;
+	}
+	hdst.hd->hd_dentry = hdst.h_dentry;
+	dinfo->di_btop = cpg->bsrc;
+	cpg->bsrc = bsrc_orig;
+
+	return err;
+}
+
+static int au_cpup_wh(struct au_cp_generic *cpg, struct file *file)
+{
+	int err;
+	aufs_bindex_t bdst;
+	struct au_dtime dt;
+	struct dentry *dentry, *parent, *h_parent, *wh_dentry;
+	struct au_branch *br;
+	struct path h_path;
+
+	dentry = cpg->dentry;
+	bdst = cpg->bdst;
+	br = au_sbr(dentry->d_sb, bdst);
+	parent = dget_parent(dentry);
+	h_parent = au_h_dptr(parent, bdst);
+	wh_dentry = au_whtmp_lkup(h_parent, br, &dentry->d_name);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry))
+		goto out;
+
+	h_path.dentry = h_parent;
+	h_path.mnt = au_br_mnt(br);
+	au_dtime_store(&dt, parent, &h_path);
+	err = au_do_cpup_wh(cpg, wh_dentry, file);
+	if (unlikely(err))
+		goto out_wh;
+
+	dget(wh_dentry);
+	h_path.dentry = wh_dentry;
+	if (!d_is_dir(wh_dentry)) {
+		/* no delegation since it is just created */
+		err = vfsub_unlink(d_inode(h_parent), &h_path,
+				   /*delegated*/NULL, /*force*/0);
+	} else
+		err = vfsub_rmdir(d_inode(h_parent), &h_path);
+	if (unlikely(err)) {
+		AuIOErr("failed remove copied-up tmp file %pd(%d)\n",
+			wh_dentry, err);
+		err = -EIO;
+	}
+	au_dtime_revert(&dt);
+	au_set_hi_wh(d_inode(dentry), bdst, wh_dentry);
+
+out_wh:
+	dput(wh_dentry);
+out:
+	dput(parent);
+	return err;
+}
+
+struct au_cpup_wh_args {
+	int *errp;
+	struct au_cp_generic *cpg;
+	struct file *file;
+};
+
+static void au_call_cpup_wh(void *args)
+{
+	struct au_cpup_wh_args *a = args;
+
+	au_pin_hdir_acquire_nest(a->cpg->pin);
+	*a->errp = au_cpup_wh(a->cpg, a->file);
+	au_pin_hdir_release(a->cpg->pin);
+}
+
+int au_sio_cpup_wh(struct au_cp_generic *cpg, struct file *file)
+{
+	int err, wkq_err;
+	aufs_bindex_t bdst;
+	struct dentry *dentry, *parent, *h_orph, *h_parent;
+	struct inode *dir, *h_dir, *h_tmpdir;
+	struct au_wbr *wbr;
+	struct au_pin wh_pin, *pin_orig;
+	struct user_namespace *h_userns;
+
+	dentry = cpg->dentry;
+	bdst = cpg->bdst;
+	parent = dget_parent(dentry);
+	dir = d_inode(parent);
+	h_orph = NULL;
+	h_parent = NULL;
+	h_dir = au_igrab(au_h_iptr(dir, bdst));
+	h_tmpdir = h_dir;
+	pin_orig = NULL;
+	if (!h_dir->i_nlink) {
+		wbr = au_sbr(dentry->d_sb, bdst)->br_wbr;
+		h_orph = wbr->wbr_orph;
+
+		h_parent = dget(au_h_dptr(parent, bdst));
+		au_set_h_dptr(parent, bdst, dget(h_orph));
+		h_tmpdir = d_inode(h_orph);
+		au_set_h_iptr(dir, bdst, au_igrab(h_tmpdir), /*flags*/0);
+
+		inode_lock_nested(h_tmpdir, AuLsc_I_PARENT3);
+		/* todo: au_h_open_pre()? */
+
+		pin_orig = cpg->pin;
+		au_pin_init(&wh_pin, dentry, bdst, AuLsc_DI_PARENT,
+			    AuLsc_I_PARENT3, cpg->pin->udba, AuPin_DI_LOCKED);
+		cpg->pin = &wh_pin;
+	}
+
+	h_userns = au_sbr_userns(dentry->d_sb, bdst);
+	if (!au_test_h_perm_sio(h_userns, h_tmpdir, MAY_EXEC | MAY_WRITE)
+	    && !au_cpup_sio_test(cpg->pin, d_inode(dentry)->i_mode))
+		err = au_cpup_wh(cpg, file);
+	else {
+		struct au_cpup_wh_args args = {
+			.errp	= &err,
+			.cpg	= cpg,
+			.file	= file
+		};
+		wkq_err = au_wkq_wait(au_call_cpup_wh, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+
+	if (h_orph) {
+		inode_unlock(h_tmpdir);
+		/* todo: au_h_open_post()? */
+		au_set_h_iptr(dir, bdst, au_igrab(h_dir), /*flags*/0);
+		au_set_h_dptr(parent, bdst, h_parent);
+		AuDebugOn(!pin_orig);
+		cpg->pin = pin_orig;
+	}
+	iput(h_dir);
+	dput(parent);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * generic routine for both of copy-up and copy-down.
+ */
+/* cf. revalidate function in file.c */
+int au_cp_dirs(struct dentry *dentry, aufs_bindex_t bdst,
+	       int (*cp)(struct dentry *dentry, aufs_bindex_t bdst,
+			 struct au_pin *pin,
+			 struct dentry *h_parent, void *arg),
+	       void *arg)
+{
+	int err;
+	struct au_pin pin;
+	struct dentry *d, *parent, *h_parent, *real_parent, *h_dentry;
+
+	err = 0;
+	parent = dget_parent(dentry);
+	if (IS_ROOT(parent))
+		goto out;
+
+	au_pin_init(&pin, dentry, bdst, AuLsc_DI_PARENT2, AuLsc_I_PARENT2,
+		    au_opt_udba(dentry->d_sb), AuPin_MNT_WRITE);
+
+	/* do not use au_dpage */
+	real_parent = parent;
+	while (1) {
+		dput(parent);
+		parent = dget_parent(dentry);
+		h_parent = au_h_dptr(parent, bdst);
+		if (h_parent)
+			goto out; /* success */
+
+		/* find top dir which is necessary to cpup */
+		do {
+			d = parent;
+			dput(parent);
+			parent = dget_parent(d);
+			di_read_lock_parent3(parent, !AuLock_IR);
+			h_parent = au_h_dptr(parent, bdst);
+			di_read_unlock(parent, !AuLock_IR);
+		} while (!h_parent);
+
+		if (d != real_parent)
+			di_write_lock_child3(d);
+
+		/* somebody else might create while we were sleeping */
+		h_dentry = au_h_dptr(d, bdst);
+		if (!h_dentry || d_is_negative(h_dentry)) {
+			if (h_dentry)
+				au_update_dbtop(d);
+
+			au_pin_set_dentry(&pin, d);
+			err = au_do_pin(&pin);
+			if (!err) {
+				err = cp(d, bdst, &pin, h_parent, arg);
+				au_unpin(&pin);
+			}
+		}
+
+		if (d != real_parent)
+			di_write_unlock(d);
+		if (unlikely(err))
+			break;
+	}
+
+out:
+	dput(parent);
+	return err;
+}
+
+static int au_cpup_dir(struct dentry *dentry, aufs_bindex_t bdst,
+		       struct au_pin *pin,
+		       struct dentry *h_parent __maybe_unused,
+		       void *arg __maybe_unused)
+{
+	struct au_cp_generic cpg = {
+		.dentry	= dentry,
+		.bdst	= bdst,
+		.bsrc	= -1,
+		.len	= 0,
+		.pin	= pin,
+		.flags	= AuCpup_DTIME
+	};
+	return au_sio_cpup_simple(&cpg);
+}
+
+int au_cpup_dirs(struct dentry *dentry, aufs_bindex_t bdst)
+{
+	return au_cp_dirs(dentry, bdst, au_cpup_dir, NULL);
+}
+
+int au_test_and_cpup_dirs(struct dentry *dentry, aufs_bindex_t bdst)
+{
+	int err;
+	struct dentry *parent;
+	struct inode *dir;
+
+	parent = dget_parent(dentry);
+	dir = d_inode(parent);
+	err = 0;
+	if (au_h_iptr(dir, bdst))
+		goto out;
+
+	di_read_unlock(parent, AuLock_IR);
+	di_write_lock_parent(parent);
+	/* someone else might change our inode while we were sleeping */
+	if (!au_h_iptr(dir, bdst))
+		err = au_cpup_dirs(dentry, bdst);
+	di_downgrade_lock(parent, AuLock_IR);
+
+out:
+	dput(parent);
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/cpup.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/cpup.h
@@ -0,0 +1,100 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * copy-up/down functions
+ */
+
+#ifndef __AUFS_CPUP_H__
+#define __AUFS_CPUP_H__
+
+#ifdef __KERNEL__
+
+#include <linux/path.h>
+
+struct inode;
+struct file;
+struct au_pin;
+
+void au_cpup_attr_flags(struct inode *dst, unsigned int iflags);
+void au_cpup_attr_timesizes(struct inode *inode);
+void au_cpup_attr_nlink(struct inode *inode, int force);
+void au_cpup_attr_changeable(struct inode *inode);
+void au_cpup_igen(struct inode *inode, struct inode *h_inode);
+void au_cpup_attr_all(struct inode *inode, int force);
+
+/* ---------------------------------------------------------------------- */
+
+struct au_cp_generic {
+	struct dentry	*dentry;
+	aufs_bindex_t	bdst, bsrc;
+	loff_t		len;
+	struct au_pin	*pin;
+	unsigned int	flags;
+};
+
+/* cpup flags */
+#define AuCpup_DTIME		1		/* do dtime_store/revert */
+#define AuCpup_KEEPLINO		(1 << 1)	/* do not clear the lower xino,
+						   for link(2) */
+#define AuCpup_RENAME		(1 << 2)	/* rename after cpup */
+#define AuCpup_HOPEN		(1 << 3)	/* call h_open_pre/post() in
+						   cpup */
+#define AuCpup_OVERWRITE	(1 << 4)	/* allow overwriting the
+						   existing entry */
+#define AuCpup_RWDST		(1 << 5)	/* force write target even if
+						   the branch is marked as RO */
+
+#ifndef CONFIG_AUFS_BR_HFSPLUS
+#undef AuCpup_HOPEN
+#define AuCpup_HOPEN		0
+#endif
+
+#define au_ftest_cpup(flags, name)	((flags) & AuCpup_##name)
+#define au_fset_cpup(flags, name) \
+	do { (flags) |= AuCpup_##name; } while (0)
+#define au_fclr_cpup(flags, name) \
+	do { (flags) &= ~AuCpup_##name; } while (0)
+
+int au_copy_file(struct file *dst, struct file *src, loff_t len);
+int au_sio_cpup_simple(struct au_cp_generic *cpg);
+int au_sio_cpdown_simple(struct au_cp_generic *cpg);
+int au_sio_cpup_wh(struct au_cp_generic *cpg, struct file *file);
+
+int au_cp_dirs(struct dentry *dentry, aufs_bindex_t bdst,
+	       int (*cp)(struct dentry *dentry, aufs_bindex_t bdst,
+			 struct au_pin *pin,
+			 struct dentry *h_parent, void *arg),
+	       void *arg);
+int au_cpup_dirs(struct dentry *dentry, aufs_bindex_t bdst);
+int au_test_and_cpup_dirs(struct dentry *dentry, aufs_bindex_t bdst);
+
+/* ---------------------------------------------------------------------- */
+
+/* keep timestamps when copyup */
+struct au_dtime {
+	struct dentry *dt_dentry;
+	struct path dt_h_path;
+	struct timespec64 dt_atime, dt_mtime;
+};
+void au_dtime_store(struct au_dtime *dt, struct dentry *dentry,
+		    struct path *h_path);
+void au_dtime_revert(struct au_dtime *dt);
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_CPUP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dbgaufs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dbgaufs.c
@@ -0,0 +1,526 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * debugfs interface
+ */
+
+#include <linux/debugfs.h>
+#include "aufs.h"
+
+#ifndef CONFIG_SYSFS
+#error DEBUG_FS depends upon SYSFS
+#endif
+
+static struct dentry *dbgaufs;
+static const mode_t dbgaufs_mode = 0444;
+
+/* 20 is max digits length of ulong 64 */
+struct dbgaufs_arg {
+	int n;
+	char a[20 * 4];
+};
+
+/*
+ * common function for all XINO files
+ */
+static int dbgaufs_xi_release(struct inode *inode __maybe_unused,
+			      struct file *file)
+{
+	void *p;
+
+	p = file->private_data;
+	if (p) {
+		/* this is struct dbgaufs_arg */
+		AuDebugOn(!au_kfree_sz_test(p));
+		au_kfree_do_rcu(p);
+	}
+	return 0;
+}
+
+static int dbgaufs_xi_open(struct file *xf, struct file *file, int do_fcnt,
+			   int cnt)
+{
+	int err;
+	struct kstat st;
+	struct dbgaufs_arg *p;
+
+	err = -ENOMEM;
+	p = kmalloc(sizeof(*p), GFP_NOFS);
+	if (unlikely(!p))
+		goto out;
+
+	err = 0;
+	p->n = 0;
+	file->private_data = p;
+	if (!xf)
+		goto out;
+
+	err = vfsub_getattr(&xf->f_path, &st);
+	if (!err) {
+		if (do_fcnt)
+			p->n = snprintf
+				(p->a, sizeof(p->a), "%d, %llux%u %lld\n",
+				 cnt, st.blocks, st.blksize,
+				 (long long)st.size);
+		else
+			p->n = snprintf(p->a, sizeof(p->a), "%llux%u %lld\n",
+					st.blocks, st.blksize,
+					(long long)st.size);
+		AuDebugOn(p->n >= sizeof(p->a));
+	} else {
+		p->n = snprintf(p->a, sizeof(p->a), "err %d\n", err);
+		err = 0;
+	}
+
+out:
+	return err;
+}
+
+static ssize_t dbgaufs_xi_read(struct file *file, char __user *buf,
+			       size_t count, loff_t *ppos)
+{
+	struct dbgaufs_arg *p;
+
+	p = file->private_data;
+	return simple_read_from_buffer(buf, count, ppos, p->a, p->n);
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct dbgaufs_plink_arg {
+	int n;
+	char a[];
+};
+
+static int dbgaufs_plink_release(struct inode *inode __maybe_unused,
+				 struct file *file)
+{
+	free_page((unsigned long)file->private_data);
+	return 0;
+}
+
+static int dbgaufs_plink_open(struct inode *inode, struct file *file)
+{
+	int err, i, limit;
+	unsigned long n, sum;
+	struct dbgaufs_plink_arg *p;
+	struct au_sbinfo *sbinfo;
+	struct super_block *sb;
+	struct hlist_bl_head *hbl;
+
+	err = -ENOMEM;
+	p = (void *)get_zeroed_page(GFP_NOFS);
+	if (unlikely(!p))
+		goto out;
+
+	err = -EFBIG;
+	sbinfo = inode->i_private;
+	sb = sbinfo->si_sb;
+	si_noflush_read_lock(sb);
+	if (au_opt_test(au_mntflags(sb), PLINK)) {
+		limit = PAGE_SIZE - sizeof(p->n);
+
+		/* the number of buckets */
+		n = snprintf(p->a + p->n, limit, "%d\n", AuPlink_NHASH);
+		p->n += n;
+		limit -= n;
+
+		sum = 0;
+		for (i = 0, hbl = sbinfo->si_plink; i < AuPlink_NHASH;
+		     i++, hbl++) {
+			n = au_hbl_count(hbl);
+			sum += n;
+
+			n = snprintf(p->a + p->n, limit, "%lu ", n);
+			p->n += n;
+			limit -= n;
+			if (unlikely(limit <= 0))
+				goto out_free;
+		}
+		p->a[p->n - 1] = '\n';
+
+		/* the sum of plinks */
+		n = snprintf(p->a + p->n, limit, "%lu\n", sum);
+		p->n += n;
+		limit -= n;
+		if (unlikely(limit <= 0))
+			goto out_free;
+	} else {
+#define str "1\n0\n0\n"
+		p->n = sizeof(str) - 1;
+		strcpy(p->a, str);
+#undef str
+	}
+	si_read_unlock(sb);
+
+	err = 0;
+	file->private_data = p;
+	goto out; /* success */
+
+out_free:
+	free_page((unsigned long)p);
+out:
+	return err;
+}
+
+static ssize_t dbgaufs_plink_read(struct file *file, char __user *buf,
+				  size_t count, loff_t *ppos)
+{
+	struct dbgaufs_plink_arg *p;
+
+	p = file->private_data;
+	return simple_read_from_buffer(buf, count, ppos, p->a, p->n);
+}
+
+static const struct file_operations dbgaufs_plink_fop = {
+	.owner		= THIS_MODULE,
+	.open		= dbgaufs_plink_open,
+	.release	= dbgaufs_plink_release,
+	.read		= dbgaufs_plink_read
+};
+
+/* ---------------------------------------------------------------------- */
+
+static int dbgaufs_xib_open(struct inode *inode, struct file *file)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+	struct super_block *sb;
+
+	sbinfo = inode->i_private;
+	sb = sbinfo->si_sb;
+	si_noflush_read_lock(sb);
+	err = dbgaufs_xi_open(sbinfo->si_xib, file, /*do_fcnt*/0, /*cnt*/0);
+	si_read_unlock(sb);
+	return err;
+}
+
+static const struct file_operations dbgaufs_xib_fop = {
+	.owner		= THIS_MODULE,
+	.open		= dbgaufs_xib_open,
+	.release	= dbgaufs_xi_release,
+	.read		= dbgaufs_xi_read
+};
+
+/* ---------------------------------------------------------------------- */
+
+#define DbgaufsXi_PREFIX "xi"
+
+static int dbgaufs_xino_open(struct inode *inode, struct file *file)
+{
+	int err, idx;
+	long l;
+	aufs_bindex_t bindex;
+	char *p, a[sizeof(DbgaufsXi_PREFIX) + 8];
+	struct au_sbinfo *sbinfo;
+	struct super_block *sb;
+	struct au_xino *xi;
+	struct file *xf;
+	struct qstr *name;
+	struct au_branch *br;
+
+	err = -ENOENT;
+	name = &file->f_path.dentry->d_name;
+	if (unlikely(name->len < sizeof(DbgaufsXi_PREFIX)
+		     || memcmp(name->name, DbgaufsXi_PREFIX,
+			       sizeof(DbgaufsXi_PREFIX) - 1)))
+		goto out;
+
+	AuDebugOn(name->len >= sizeof(a));
+	memcpy(a, name->name, name->len);
+	a[name->len] = '\0';
+	p = strchr(a, '-');
+	if (p)
+		*p = '\0';
+	err = kstrtol(a + sizeof(DbgaufsXi_PREFIX) - 1, 10, &l);
+	if (unlikely(err))
+		goto out;
+	bindex = l;
+	idx = 0;
+	if (p) {
+		err = kstrtol(p + 1, 10, &l);
+		if (unlikely(err))
+			goto out;
+		idx = l;
+	}
+
+	err = -ENOENT;
+	sbinfo = inode->i_private;
+	sb = sbinfo->si_sb;
+	si_noflush_read_lock(sb);
+	if (unlikely(bindex < 0 || bindex > au_sbbot(sb)))
+		goto out_si;
+	br = au_sbr(sb, bindex);
+	xi = br->br_xino;
+	if (unlikely(idx >= xi->xi_nfile))
+		goto out_si;
+	xf = au_xino_file(xi, idx);
+	if (xf)
+		err = dbgaufs_xi_open(xf, file, /*do_fcnt*/1,
+				      au_xino_count(br));
+
+out_si:
+	si_read_unlock(sb);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static const struct file_operations dbgaufs_xino_fop = {
+	.owner		= THIS_MODULE,
+	.open		= dbgaufs_xino_open,
+	.release	= dbgaufs_xi_release,
+	.read		= dbgaufs_xi_read
+};
+
+void dbgaufs_xino_del(struct au_branch *br)
+{
+	struct dentry *dbgaufs;
+
+	dbgaufs = br->br_dbgaufs;
+	if (!dbgaufs)
+		return;
+
+	br->br_dbgaufs = NULL;
+	/* debugfs acquires the parent i_mutex */
+	lockdep_off();
+	debugfs_remove(dbgaufs);
+	lockdep_on();
+}
+
+void dbgaufs_brs_del(struct super_block *sb, aufs_bindex_t bindex)
+{
+	aufs_bindex_t bbot;
+	struct au_branch *br;
+
+	if (!au_sbi(sb)->si_dbgaufs)
+		return;
+
+	bbot = au_sbbot(sb);
+	for (; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		dbgaufs_xino_del(br);
+	}
+}
+
+static void dbgaufs_br_do_add(struct super_block *sb, aufs_bindex_t bindex,
+			      unsigned int idx, struct dentry *parent,
+			      struct au_sbinfo *sbinfo)
+{
+	struct au_branch *br;
+	struct dentry *d;
+	/* "xi" bindex(5) "-" idx(2) NULL */
+	char name[sizeof(DbgaufsXi_PREFIX) + 8];
+
+	if (!idx)
+		snprintf(name, sizeof(name), DbgaufsXi_PREFIX "%d", bindex);
+	else
+		snprintf(name, sizeof(name), DbgaufsXi_PREFIX "%d-%u",
+			 bindex, idx);
+	br = au_sbr(sb, bindex);
+	if (br->br_dbgaufs) {
+		struct qstr qstr = QSTR_INIT(name, strlen(name));
+
+		if (!au_qstreq(&br->br_dbgaufs->d_name, &qstr)) {
+			/* debugfs acquires the parent i_mutex */
+			lockdep_off();
+			d = debugfs_rename(parent, br->br_dbgaufs, parent,
+					   name);
+			lockdep_on();
+			if (unlikely(!d))
+				pr_warn("failed renaming %pd/%s, ignored.\n",
+					parent, name);
+		}
+	} else {
+		lockdep_off();
+		br->br_dbgaufs = debugfs_create_file(name, dbgaufs_mode, parent,
+						     sbinfo, &dbgaufs_xino_fop);
+		lockdep_on();
+		if (unlikely(!br->br_dbgaufs))
+			pr_warn("failed creating %pd/%s, ignored.\n",
+				parent, name);
+	}
+}
+
+static void dbgaufs_br_add(struct super_block *sb, aufs_bindex_t bindex,
+			   struct dentry *parent, struct au_sbinfo *sbinfo)
+{
+	struct au_branch *br;
+	struct au_xino *xi;
+	unsigned int u;
+
+	br = au_sbr(sb, bindex);
+	xi = br->br_xino;
+	for (u = 0; u < xi->xi_nfile; u++)
+		dbgaufs_br_do_add(sb, bindex, u, parent, sbinfo);
+}
+
+void dbgaufs_brs_add(struct super_block *sb, aufs_bindex_t bindex, int topdown)
+{
+	struct au_sbinfo *sbinfo;
+	struct dentry *parent;
+	aufs_bindex_t bbot;
+
+	if (!au_opt_test(au_mntflags(sb), XINO))
+		return;
+
+	sbinfo = au_sbi(sb);
+	parent = sbinfo->si_dbgaufs;
+	if (!parent)
+		return;
+
+	bbot = au_sbbot(sb);
+	if (topdown)
+		for (; bindex <= bbot; bindex++)
+			dbgaufs_br_add(sb, bindex, parent, sbinfo);
+	else
+		for (; bbot >= bindex; bbot--)
+			dbgaufs_br_add(sb, bbot, parent, sbinfo);
+}
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_EXPORT
+static int dbgaufs_xigen_open(struct inode *inode, struct file *file)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+	struct super_block *sb;
+
+	sbinfo = inode->i_private;
+	sb = sbinfo->si_sb;
+	si_noflush_read_lock(sb);
+	err = dbgaufs_xi_open(sbinfo->si_xigen, file, /*do_fcnt*/0, /*cnt*/0);
+	si_read_unlock(sb);
+	return err;
+}
+
+static const struct file_operations dbgaufs_xigen_fop = {
+	.owner		= THIS_MODULE,
+	.open		= dbgaufs_xigen_open,
+	.release	= dbgaufs_xi_release,
+	.read		= dbgaufs_xi_read
+};
+
+static int dbgaufs_xigen_init(struct au_sbinfo *sbinfo)
+{
+	int err;
+
+	/*
+	 * This function is a dynamic '__init' function actually,
+	 * so the tiny check for si_rwsem is unnecessary.
+	 */
+	/* AuRwMustWriteLock(&sbinfo->si_rwsem); */
+
+	err = -EIO;
+	sbinfo->si_dbgaufs_xigen = debugfs_create_file
+		("xigen", dbgaufs_mode, sbinfo->si_dbgaufs, sbinfo,
+		 &dbgaufs_xigen_fop);
+	if (sbinfo->si_dbgaufs_xigen)
+		err = 0;
+
+	return err;
+}
+#else
+static int dbgaufs_xigen_init(struct au_sbinfo *sbinfo)
+{
+	return 0;
+}
+#endif /* CONFIG_AUFS_EXPORT */
+
+/* ---------------------------------------------------------------------- */
+
+void dbgaufs_si_fin(struct au_sbinfo *sbinfo)
+{
+	/*
+	 * This function is a dynamic '__fin' function actually,
+	 * so the tiny check for si_rwsem is unnecessary.
+	 */
+	/* AuRwMustWriteLock(&sbinfo->si_rwsem); */
+
+	debugfs_remove_recursive(sbinfo->si_dbgaufs);
+	sbinfo->si_dbgaufs = NULL;
+}
+
+int dbgaufs_si_init(struct au_sbinfo *sbinfo)
+{
+	int err;
+	char name[SysaufsSiNameLen];
+
+	/*
+	 * This function is a dynamic '__init' function actually,
+	 * so the tiny check for si_rwsem is unnecessary.
+	 */
+	/* AuRwMustWriteLock(&sbinfo->si_rwsem); */
+
+	err = -ENOENT;
+	if (!dbgaufs) {
+		AuErr1("/debug/aufs is uninitialized\n");
+		goto out;
+	}
+
+	err = -EIO;
+	sysaufs_name(sbinfo, name);
+	sbinfo->si_dbgaufs = debugfs_create_dir(name, dbgaufs);
+	if (unlikely(!sbinfo->si_dbgaufs))
+		goto out;
+
+	/* regardless plink/noplink option */
+	sbinfo->si_dbgaufs_plink = debugfs_create_file
+		("plink", dbgaufs_mode, sbinfo->si_dbgaufs, sbinfo,
+		 &dbgaufs_plink_fop);
+	if (unlikely(!sbinfo->si_dbgaufs_plink))
+		goto out_dir;
+
+	/* regardless xino/noxino option */
+	sbinfo->si_dbgaufs_xib = debugfs_create_file
+		("xib", dbgaufs_mode, sbinfo->si_dbgaufs, sbinfo,
+		 &dbgaufs_xib_fop);
+	if (unlikely(!sbinfo->si_dbgaufs_xib))
+		goto out_dir;
+
+	err = dbgaufs_xigen_init(sbinfo);
+	if (!err)
+		goto out; /* success */
+
+out_dir:
+	dbgaufs_si_fin(sbinfo);
+out:
+	if (unlikely(err))
+		pr_err("debugfs/aufs failed\n");
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void dbgaufs_fin(void)
+{
+	debugfs_remove(dbgaufs);
+}
+
+int __init dbgaufs_init(void)
+{
+	int err;
+
+	err = -EIO;
+	dbgaufs = debugfs_create_dir(AUFS_NAME, NULL);
+	if (dbgaufs)
+		err = 0;
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dbgaufs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dbgaufs.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * debugfs interface
+ */
+
+#ifndef __DBGAUFS_H__
+#define __DBGAUFS_H__
+
+#ifdef __KERNEL__
+
+struct super_block;
+struct au_sbinfo;
+struct au_branch;
+
+#ifdef CONFIG_DEBUG_FS
+/* dbgaufs.c */
+void dbgaufs_xino_del(struct au_branch *br);
+void dbgaufs_brs_del(struct super_block *sb, aufs_bindex_t bindex);
+void dbgaufs_brs_add(struct super_block *sb, aufs_bindex_t bindex, int topdown);
+void dbgaufs_si_fin(struct au_sbinfo *sbinfo);
+int dbgaufs_si_init(struct au_sbinfo *sbinfo);
+void dbgaufs_fin(void);
+int __init dbgaufs_init(void);
+#else
+AuStubVoid(dbgaufs_xino_del, struct au_branch *br)
+AuStubVoid(dbgaufs_brs_del, struct super_block *sb, aufs_bindex_t bindex)
+AuStubVoid(dbgaufs_brs_add, struct super_block *sb, aufs_bindex_t bindex,
+	   int topdown)
+AuStubVoid(dbgaufs_si_fin, struct au_sbinfo *sbinfo)
+AuStubInt0(dbgaufs_si_init, struct au_sbinfo *sbinfo)
+AuStubVoid(dbgaufs_fin, void)
+AuStubInt0(__init dbgaufs_init, void)
+#endif /* CONFIG_DEBUG_FS */
+
+#endif /* __KERNEL__ */
+#endif /* __DBGAUFS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dcsub.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dcsub.c
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sub-routines for dentry cache
+ */
+
+#include "aufs.h"
+
+static void au_dpage_free(struct au_dpage *dpage)
+{
+	int i;
+	struct dentry **p;
+
+	p = dpage->dentries;
+	for (i = 0; i < dpage->ndentry; i++)
+		dput(*p++);
+	free_page((unsigned long)dpage->dentries);
+}
+
+int au_dpages_init(struct au_dcsub_pages *dpages, gfp_t gfp)
+{
+	int err;
+	void *p;
+
+	err = -ENOMEM;
+	dpages->dpages = kmalloc(sizeof(*dpages->dpages), gfp);
+	if (unlikely(!dpages->dpages))
+		goto out;
+
+	p = (void *)__get_free_page(gfp);
+	if (unlikely(!p))
+		goto out_dpages;
+
+	dpages->dpages[0].ndentry = 0;
+	dpages->dpages[0].dentries = p;
+	dpages->ndpage = 1;
+	return 0; /* success */
+
+out_dpages:
+	au_kfree_try_rcu(dpages->dpages);
+out:
+	return err;
+}
+
+void au_dpages_free(struct au_dcsub_pages *dpages)
+{
+	int i;
+	struct au_dpage *p;
+
+	p = dpages->dpages;
+	for (i = 0; i < dpages->ndpage; i++)
+		au_dpage_free(p++);
+	au_kfree_try_rcu(dpages->dpages);
+}
+
+static int au_dpages_append(struct au_dcsub_pages *dpages,
+			    struct dentry *dentry, gfp_t gfp)
+{
+	int err, sz;
+	struct au_dpage *dpage;
+	void *p;
+
+	dpage = dpages->dpages + dpages->ndpage - 1;
+	sz = PAGE_SIZE / sizeof(dentry);
+	if (unlikely(dpage->ndentry >= sz)) {
+		AuLabel(new dpage);
+		err = -ENOMEM;
+		sz = dpages->ndpage * sizeof(*dpages->dpages);
+		p = au_kzrealloc(dpages->dpages, sz,
+				 sz + sizeof(*dpages->dpages), gfp,
+				 /*may_shrink*/0);
+		if (unlikely(!p))
+			goto out;
+
+		dpages->dpages = p;
+		dpage = dpages->dpages + dpages->ndpage;
+		p = (void *)__get_free_page(gfp);
+		if (unlikely(!p))
+			goto out;
+
+		dpage->ndentry = 0;
+		dpage->dentries = p;
+		dpages->ndpage++;
+	}
+
+	AuDebugOn(au_dcount(dentry) <= 0);
+	dpage->dentries[dpage->ndentry++] = dget_dlock(dentry);
+	return 0; /* success */
+
+out:
+	return err;
+}
+
+/* todo: BAD approach */
+/* copied from linux/fs/dcache.c */
+enum d_walk_ret {
+	D_WALK_CONTINUE,
+	D_WALK_QUIT,
+	D_WALK_NORETRY,
+	D_WALK_SKIP,
+};
+
+extern void d_walk(struct dentry *parent, void *data,
+		   enum d_walk_ret (*enter)(void *, struct dentry *));
+
+struct ac_dpages_arg {
+	int err;
+	struct au_dcsub_pages *dpages;
+	struct super_block *sb;
+	au_dpages_test test;
+	void *arg;
+};
+
+static enum d_walk_ret au_call_dpages_append(void *_arg, struct dentry *dentry)
+{
+	enum d_walk_ret ret;
+	struct ac_dpages_arg *arg = _arg;
+
+	ret = D_WALK_CONTINUE;
+	if (dentry->d_sb == arg->sb
+	    && !IS_ROOT(dentry)
+	    && au_dcount(dentry) > 0
+	    && au_di(dentry)
+	    && (!arg->test || arg->test(dentry, arg->arg))) {
+		arg->err = au_dpages_append(arg->dpages, dentry, GFP_ATOMIC);
+		if (unlikely(arg->err))
+			ret = D_WALK_QUIT;
+	}
+
+	return ret;
+}
+
+int au_dcsub_pages(struct au_dcsub_pages *dpages, struct dentry *root,
+		   au_dpages_test test, void *arg)
+{
+	struct ac_dpages_arg args = {
+		.err	= 0,
+		.dpages	= dpages,
+		.sb	= root->d_sb,
+		.test	= test,
+		.arg	= arg
+	};
+
+	d_walk(root, &args, au_call_dpages_append);
+
+	return args.err;
+}
+
+int au_dcsub_pages_rev(struct au_dcsub_pages *dpages, struct dentry *dentry,
+		       int do_include, au_dpages_test test, void *arg)
+{
+	int err;
+
+	err = 0;
+	write_seqlock(&rename_lock);
+	spin_lock(&dentry->d_lock);
+	if (do_include
+	    && au_dcount(dentry) > 0
+	    && (!test || test(dentry, arg)))
+		err = au_dpages_append(dpages, dentry, GFP_ATOMIC);
+	spin_unlock(&dentry->d_lock);
+	if (unlikely(err))
+		goto out;
+
+	/*
+	 * RCU for vfsmount is unnecessary since this is a traverse in a single
+	 * mount
+	 */
+	while (!IS_ROOT(dentry)) {
+		dentry = dentry->d_parent; /* rename_lock is locked */
+		spin_lock(&dentry->d_lock);
+		if (au_dcount(dentry) > 0
+		    && (!test || test(dentry, arg)))
+			err = au_dpages_append(dpages, dentry, GFP_ATOMIC);
+		spin_unlock(&dentry->d_lock);
+		if (unlikely(err))
+			break;
+	}
+
+out:
+	write_sequnlock(&rename_lock);
+	return err;
+}
+
+static inline int au_dcsub_dpages_aufs(struct dentry *dentry, void *arg)
+{
+	return au_di(dentry) && dentry->d_sb == arg;
+}
+
+int au_dcsub_pages_rev_aufs(struct au_dcsub_pages *dpages,
+			    struct dentry *dentry, int do_include)
+{
+	return au_dcsub_pages_rev(dpages, dentry, do_include,
+				  au_dcsub_dpages_aufs, dentry->d_sb);
+}
+
+int au_test_subdir(struct dentry *d1, struct dentry *d2)
+{
+	struct path path[2] = {
+		{
+			.dentry = d1
+		},
+		{
+			.dentry = d2
+		}
+	};
+
+	return path_is_under(path + 0, path + 1);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dcsub.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dcsub.h
@@ -0,0 +1,137 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sub-routines for dentry cache
+ */
+
+#ifndef __AUFS_DCSUB_H__
+#define __AUFS_DCSUB_H__
+
+#ifdef __KERNEL__
+
+#include <linux/dcache.h>
+#include <linux/fs.h>
+
+struct au_dpage {
+	int ndentry;
+	struct dentry **dentries;
+};
+
+struct au_dcsub_pages {
+	int ndpage;
+	struct au_dpage *dpages;
+};
+
+/* ---------------------------------------------------------------------- */
+
+/* dcsub.c */
+int au_dpages_init(struct au_dcsub_pages *dpages, gfp_t gfp);
+void au_dpages_free(struct au_dcsub_pages *dpages);
+typedef int (*au_dpages_test)(struct dentry *dentry, void *arg);
+int au_dcsub_pages(struct au_dcsub_pages *dpages, struct dentry *root,
+		   au_dpages_test test, void *arg);
+int au_dcsub_pages_rev(struct au_dcsub_pages *dpages, struct dentry *dentry,
+		       int do_include, au_dpages_test test, void *arg);
+int au_dcsub_pages_rev_aufs(struct au_dcsub_pages *dpages,
+			    struct dentry *dentry, int do_include);
+int au_test_subdir(struct dentry *d1, struct dentry *d2);
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * todo: in linux-3.13, several similar (but faster) helpers are added to
+ * include/linux/dcache.h. Try them (in the future).
+ */
+
+static inline int au_d_hashed_positive(struct dentry *d)
+{
+	int err;
+	struct inode *inode = d_inode(d);
+
+	err = 0;
+	if (unlikely(d_unhashed(d)
+		     || d_is_negative(d)
+		     || !inode->i_nlink))
+		err = -ENOENT;
+	return err;
+}
+
+static inline int au_d_linkable(struct dentry *d)
+{
+	int err;
+	struct inode *inode = d_inode(d);
+
+	err = au_d_hashed_positive(d);
+	if (err
+	    && d_is_positive(d)
+	    && (inode->i_state & I_LINKABLE))
+		err = 0;
+	return err;
+}
+
+static inline int au_d_alive(struct dentry *d)
+{
+	int err;
+	struct inode *inode;
+
+	err = 0;
+	if (!IS_ROOT(d))
+		err = au_d_hashed_positive(d);
+	else {
+		inode = d_inode(d);
+		if (unlikely(d_unlinked(d)
+			     || d_is_negative(d)
+			     || !inode->i_nlink))
+			err = -ENOENT;
+	}
+	return err;
+}
+
+static inline int au_alive_dir(struct dentry *d)
+{
+	int err;
+
+	err = au_d_alive(d);
+	if (unlikely(err || IS_DEADDIR(d_inode(d))))
+		err = -ENOENT;
+	return err;
+}
+
+static inline int au_qstreq(struct qstr *a, struct qstr *b)
+{
+	return a->len == b->len
+		&& !memcmp(a->name, b->name, a->len);
+}
+
+/*
+ * by the commit
+ * 360f547 2015-01-25 dcache: let the dentry count go down to zero without
+ *			taking d_lock
+ * the type of d_lockref.count became int, but the inlined function d_count()
+ * still returns unsigned int.
+ * I don't know why. Maybe it is for every d_count() users?
+ * Anyway au_dcount() lives on.
+ */
+static inline int au_dcount(struct dentry *d)
+{
+	return (int)d_count(d);
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_DCSUB_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/debug.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/debug.c
@@ -0,0 +1,444 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * debug print functions
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+/* Returns 0, or -errno.  arg is in kp->arg. */
+static int param_atomic_t_set(const char *val, const struct kernel_param *kp)
+{
+	int err, n;
+
+	err = kstrtoint(val, 0, &n);
+	if (!err) {
+		if (n > 0)
+			au_debug_on();
+		else
+			au_debug_off();
+	}
+	return err;
+}
+
+/* Returns length written or -errno.  Buffer is 4k (ie. be short!) */
+static int param_atomic_t_get(char *buffer, const struct kernel_param *kp)
+{
+	atomic_t *a;
+
+	a = kp->arg;
+	return sprintf(buffer, "%d", atomic_read(a));
+}
+
+static struct kernel_param_ops param_ops_atomic_t = {
+	.set = param_atomic_t_set,
+	.get = param_atomic_t_get
+	/* void (*free)(void *arg) */
+};
+
+atomic_t aufs_debug = ATOMIC_INIT(0);
+MODULE_PARM_DESC(debug, "debug print");
+module_param_named(debug, aufs_debug, atomic_t, 0664);
+
+DEFINE_MUTEX(au_dbg_mtx);	/* just to serialize the dbg msgs */
+char *au_plevel = KERN_DEBUG;
+#define dpri(fmt, ...) do {					\
+	if ((au_plevel						\
+	     && strcmp(au_plevel, KERN_DEBUG))			\
+	    || au_debug_test())					\
+		printk("%s" fmt, au_plevel, ##__VA_ARGS__);	\
+} while (0)
+
+/* ---------------------------------------------------------------------- */
+
+void au_dpri_whlist(struct au_nhash *whlist)
+{
+	unsigned long ul, n;
+	struct hlist_head *head;
+	struct au_vdir_wh *pos;
+
+	n = whlist->nh_num;
+	head = whlist->nh_head;
+	for (ul = 0; ul < n; ul++) {
+		hlist_for_each_entry(pos, head, wh_hash)
+			dpri("b%d, %.*s, %d\n",
+			     pos->wh_bindex,
+			     pos->wh_str.len, pos->wh_str.name,
+			     pos->wh_str.len);
+		head++;
+	}
+}
+
+void au_dpri_vdir(struct au_vdir *vdir)
+{
+	unsigned long ul;
+	union au_vdir_deblk_p p;
+	unsigned char *o;
+
+	if (!vdir || IS_ERR(vdir)) {
+		dpri("err %ld\n", PTR_ERR(vdir));
+		return;
+	}
+
+	dpri("deblk %u, nblk %lu, deblk %p, last{%lu, %p}, ver %llu\n",
+	     vdir->vd_deblk_sz, vdir->vd_nblk, vdir->vd_deblk,
+	     vdir->vd_last.ul, vdir->vd_last.p.deblk, vdir->vd_version);
+	for (ul = 0; ul < vdir->vd_nblk; ul++) {
+		p.deblk = vdir->vd_deblk[ul];
+		o = p.deblk;
+		dpri("[%lu]: %p\n", ul, o);
+	}
+}
+
+static int do_pri_inode(aufs_bindex_t bindex, struct inode *inode, int hn,
+			struct dentry *wh)
+{
+	char *n = NULL;
+	int l = 0;
+
+	if (!inode || IS_ERR(inode)) {
+		dpri("i%d: err %ld\n", bindex, PTR_ERR(inode));
+		return -1;
+	}
+
+	/* the type of i_blocks depends upon CONFIG_LBDAF */
+	BUILD_BUG_ON(sizeof(inode->i_blocks) != sizeof(unsigned long)
+		     && sizeof(inode->i_blocks) != sizeof(u64));
+	if (wh) {
+		n = (void *)wh->d_name.name;
+		l = wh->d_name.len;
+	}
+
+	dpri("i%d: %p, i%lu, %s, cnt %d, nl %u, 0%o, sz %llu, blk %llu,"
+	     " hn %d, ct %lld, np %lu, st 0x%lx, f 0x%x, v %llu, g %x%s%.*s\n",
+	     bindex, inode,
+	     inode->i_ino, inode->i_sb ? au_sbtype(inode->i_sb) : "??",
+	     atomic_read(&inode->i_count), inode->i_nlink, inode->i_mode,
+	     i_size_read(inode), (unsigned long long)inode->i_blocks,
+	     hn, (long long)timespec64_to_ns(&inode->i_ctime) & 0x0ffff,
+	     inode->i_mapping ? inode->i_mapping->nrpages : 0,
+	     inode->i_state, inode->i_flags, inode_peek_iversion(inode),
+	     inode->i_generation,
+	     l ? ", wh " : "", l, n);
+	return 0;
+}
+
+void au_dpri_inode(struct inode *inode)
+{
+	struct au_iinfo *iinfo;
+	struct au_hinode *hi;
+	aufs_bindex_t bindex;
+	int err, hn;
+
+	err = do_pri_inode(-1, inode, -1, NULL);
+	if (err || !au_test_aufs(inode->i_sb) || au_is_bad_inode(inode))
+		return;
+
+	iinfo = au_ii(inode);
+	dpri("i-1: btop %d, bbot %d, gen %d\n",
+	     iinfo->ii_btop, iinfo->ii_bbot, au_iigen(inode, NULL));
+	if (iinfo->ii_btop < 0)
+		return;
+	hn = 0;
+	for (bindex = iinfo->ii_btop; bindex <= iinfo->ii_bbot; bindex++) {
+		hi = au_hinode(iinfo, bindex);
+		hn = !!au_hn(hi);
+		do_pri_inode(bindex, hi->hi_inode, hn, hi->hi_whdentry);
+	}
+}
+
+void au_dpri_dalias(struct inode *inode)
+{
+	struct dentry *d;
+
+	spin_lock(&inode->i_lock);
+	hlist_for_each_entry(d, &inode->i_dentry, d_u.d_alias)
+		au_dpri_dentry(d);
+	spin_unlock(&inode->i_lock);
+}
+
+static int do_pri_dentry(aufs_bindex_t bindex, struct dentry *dentry)
+{
+	struct dentry *wh = NULL;
+	int hn;
+	struct inode *inode;
+	struct au_iinfo *iinfo;
+	struct au_hinode *hi;
+
+	if (!dentry || IS_ERR(dentry)) {
+		dpri("d%d: err %ld\n", bindex, PTR_ERR(dentry));
+		return -1;
+	}
+	/* do not call dget_parent() here */
+	/* note: access d_xxx without d_lock */
+	dpri("d%d: %p, %pd2?, %s, cnt %d, flags 0x%x, %shashed\n",
+	     bindex, dentry, dentry,
+	     dentry->d_sb ? au_sbtype(dentry->d_sb) : "??",
+	     au_dcount(dentry), dentry->d_flags,
+	     d_unhashed(dentry) ? "un" : "");
+	hn = -1;
+	inode = NULL;
+	if (d_is_positive(dentry))
+		inode = d_inode(dentry);
+	if (inode
+	    && au_test_aufs(dentry->d_sb)
+	    && bindex >= 0
+	    && !au_is_bad_inode(inode)) {
+		iinfo = au_ii(inode);
+		hi = au_hinode(iinfo, bindex);
+		hn = !!au_hn(hi);
+		wh = hi->hi_whdentry;
+	}
+	do_pri_inode(bindex, inode, hn, wh);
+	return 0;
+}
+
+void au_dpri_dentry(struct dentry *dentry)
+{
+	struct au_dinfo *dinfo;
+	aufs_bindex_t bindex;
+	int err;
+
+	err = do_pri_dentry(-1, dentry);
+	if (err || !au_test_aufs(dentry->d_sb))
+		return;
+
+	dinfo = au_di(dentry);
+	if (!dinfo)
+		return;
+	dpri("d-1: btop %d, bbot %d, bwh %d, bdiropq %d, gen %d, tmp %d\n",
+	     dinfo->di_btop, dinfo->di_bbot,
+	     dinfo->di_bwh, dinfo->di_bdiropq, au_digen(dentry),
+	     dinfo->di_tmpfile);
+	if (dinfo->di_btop < 0)
+		return;
+	for (bindex = dinfo->di_btop; bindex <= dinfo->di_bbot; bindex++)
+		do_pri_dentry(bindex, au_hdentry(dinfo, bindex)->hd_dentry);
+}
+
+static int do_pri_file(aufs_bindex_t bindex, struct file *file)
+{
+	char a[32];
+
+	if (!file || IS_ERR(file)) {
+		dpri("f%d: err %ld\n", bindex, PTR_ERR(file));
+		return -1;
+	}
+	a[0] = 0;
+	if (bindex < 0
+	    && !IS_ERR_OR_NULL(file->f_path.dentry)
+	    && au_test_aufs(file->f_path.dentry->d_sb)
+	    && au_fi(file))
+		snprintf(a, sizeof(a), ", gen %d, mmapped %d",
+			 au_figen(file), atomic_read(&au_fi(file)->fi_mmapped));
+	dpri("f%d: mode 0x%x, flags 0%o, cnt %ld, v %llu, pos %llu%s\n",
+	     bindex, file->f_mode, file->f_flags, (long)file_count(file),
+	     file->f_version, file->f_pos, a);
+	if (!IS_ERR_OR_NULL(file->f_path.dentry))
+		do_pri_dentry(bindex, file->f_path.dentry);
+	return 0;
+}
+
+void au_dpri_file(struct file *file)
+{
+	struct au_finfo *finfo;
+	struct au_fidir *fidir;
+	struct au_hfile *hfile;
+	aufs_bindex_t bindex;
+	int err;
+
+	err = do_pri_file(-1, file);
+	if (err
+	    || IS_ERR_OR_NULL(file->f_path.dentry)
+	    || !au_test_aufs(file->f_path.dentry->d_sb))
+		return;
+
+	finfo = au_fi(file);
+	if (!finfo)
+		return;
+	if (finfo->fi_btop < 0)
+		return;
+	fidir = finfo->fi_hdir;
+	if (!fidir)
+		do_pri_file(finfo->fi_btop, finfo->fi_htop.hf_file);
+	else
+		for (bindex = finfo->fi_btop;
+		     bindex >= 0 && bindex <= fidir->fd_bbot;
+		     bindex++) {
+			hfile = fidir->fd_hfile + bindex;
+			do_pri_file(bindex, hfile ? hfile->hf_file : NULL);
+		}
+}
+
+static int do_pri_br(aufs_bindex_t bindex, struct au_branch *br)
+{
+	struct vfsmount *mnt;
+	struct super_block *sb;
+
+	if (!br || IS_ERR(br))
+		goto out;
+	mnt = au_br_mnt(br);
+	if (!mnt || IS_ERR(mnt))
+		goto out;
+	sb = mnt->mnt_sb;
+	if (!sb || IS_ERR(sb))
+		goto out;
+
+	dpri("s%d: {perm 0x%x, id %d, wbr %p}, "
+	     "%s, dev 0x%02x%02x, flags 0x%lx, cnt %d, active %d, "
+	     "xino %d\n",
+	     bindex, br->br_perm, br->br_id, br->br_wbr,
+	     au_sbtype(sb), MAJOR(sb->s_dev), MINOR(sb->s_dev),
+	     sb->s_flags, sb->s_count,
+	     atomic_read(&sb->s_active),
+	     !!au_xino_file(br->br_xino, /*idx*/-1));
+	return 0;
+
+out:
+	dpri("s%d: err %ld\n", bindex, PTR_ERR(br));
+	return -1;
+}
+
+void au_dpri_sb(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+	aufs_bindex_t bindex;
+	int err;
+	/* to reduce stack size */
+	struct {
+		struct vfsmount mnt;
+		struct au_branch fake;
+	} *a;
+
+	/* this function can be called from magic sysrq */
+	a = kzalloc(sizeof(*a), GFP_ATOMIC);
+	if (unlikely(!a)) {
+		dpri("no memory\n");
+		return;
+	}
+
+	a->mnt.mnt_sb = sb;
+	a->fake.br_path.mnt = &a->mnt;
+	err = do_pri_br(-1, &a->fake);
+	au_kfree_rcu(a);
+	dpri("dev 0x%x\n", sb->s_dev);
+	if (err || !au_test_aufs(sb))
+		return;
+
+	sbinfo = au_sbi(sb);
+	if (!sbinfo)
+		return;
+	dpri("nw %d, gen %u, kobj %d\n",
+	     atomic_read(&sbinfo->si_nowait.nw_len), sbinfo->si_generation,
+	     kref_read(&sbinfo->si_kobj.kref));
+	for (bindex = 0; bindex <= sbinfo->si_bbot; bindex++)
+		do_pri_br(bindex, sbinfo->si_branch[0 + bindex]);
+}
+
+/* ---------------------------------------------------------------------- */
+
+void __au_dbg_verify_dinode(struct dentry *dentry, const char *func, int line)
+{
+	struct inode *h_inode, *inode = d_inode(dentry);
+	struct dentry *h_dentry;
+	aufs_bindex_t bindex, bbot, bi;
+
+	if (!inode /* || au_di(dentry)->di_lsc == AuLsc_DI_TMP */)
+		return;
+
+	bbot = au_dbbot(dentry);
+	bi = au_ibbot(inode);
+	if (bi < bbot)
+		bbot = bi;
+	bindex = au_dbtop(dentry);
+	bi = au_ibtop(inode);
+	if (bi > bindex)
+		bindex = bi;
+
+	for (; bindex <= bbot; bindex++) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (!h_dentry)
+			continue;
+		h_inode = au_h_iptr(inode, bindex);
+		if (unlikely(h_inode != d_inode(h_dentry))) {
+			au_debug_on();
+			AuDbg("b%d, %s:%d\n", bindex, func, line);
+			AuDbgDentry(dentry);
+			AuDbgInode(inode);
+			au_debug_off();
+			if (au_test_fuse(h_inode->i_sb))
+				WARN_ON_ONCE(1);
+			else
+				BUG();
+		}
+	}
+}
+
+void au_dbg_verify_gen(struct dentry *parent, unsigned int sigen)
+{
+	int err, i, j;
+	struct au_dcsub_pages dpages;
+	struct au_dpage *dpage;
+	struct dentry **dentries;
+
+	err = au_dpages_init(&dpages, GFP_NOFS);
+	AuDebugOn(err);
+	err = au_dcsub_pages_rev_aufs(&dpages, parent, /*do_include*/1);
+	AuDebugOn(err);
+	for (i = dpages.ndpage - 1; !err && i >= 0; i--) {
+		dpage = dpages.dpages + i;
+		dentries = dpage->dentries;
+		for (j = dpage->ndentry - 1; !err && j >= 0; j--)
+			AuDebugOn(au_digen_test(dentries[j], sigen));
+	}
+	au_dpages_free(&dpages);
+}
+
+void au_dbg_verify_kthread(void)
+{
+	if (au_wkq_test()) {
+		au_dbg_blocked();
+		/*
+		 * It may be recursive, but udba=notify between two aufs mounts,
+		 * where a single ro branch is shared, is not a problem.
+		 */
+		/* WARN_ON(1); */
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+int __init au_debug_init(void)
+{
+	aufs_bindex_t bindex;
+	struct au_vdir_destr destr;
+
+	bindex = -1;
+	AuDebugOn(bindex >= 0);
+
+	destr.len = -1;
+	AuDebugOn(destr.len < NAME_MAX);
+
+#ifdef CONFIG_4KSTACKS
+	pr_warn("CONFIG_4KSTACKS is defined.\n");
+#endif
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/debug.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/debug.h
@@ -0,0 +1,226 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * debug print functions
+ */
+
+#ifndef __AUFS_DEBUG_H__
+#define __AUFS_DEBUG_H__
+
+#ifdef __KERNEL__
+
+#include <linux/atomic.h>
+#include <linux/module.h>
+#include <linux/kallsyms.h>
+#include <linux/sysrq.h>
+
+#ifdef CONFIG_AUFS_DEBUG
+#define AuDebugOn(a)		BUG_ON(a)
+
+/* module parameter */
+extern atomic_t aufs_debug;
+static inline void au_debug_on(void)
+{
+	atomic_inc(&aufs_debug);
+}
+static inline void au_debug_off(void)
+{
+	atomic_dec_if_positive(&aufs_debug);
+}
+
+static inline int au_debug_test(void)
+{
+	return atomic_read(&aufs_debug) > 0;
+}
+#else
+#define AuDebugOn(a)		do {} while (0)
+AuStubVoid(au_debug_on, void)
+AuStubVoid(au_debug_off, void)
+AuStubInt0(au_debug_test, void)
+#endif /* CONFIG_AUFS_DEBUG */
+
+#define param_check_atomic_t(name, p) __param_check(name, p, atomic_t)
+
+/* ---------------------------------------------------------------------- */
+
+/* debug print */
+
+#define AuDbg(fmt, ...) do { \
+	if (au_debug_test()) \
+		pr_debug("DEBUG: " fmt, ##__VA_ARGS__); \
+} while (0)
+#define AuLabel(l)		AuDbg(#l "\n")
+#define AuIOErr(fmt, ...)	pr_err("I/O Error, " fmt, ##__VA_ARGS__)
+#define AuWarn1(fmt, ...) do { \
+	static unsigned char _c; \
+	if (!_c++) \
+		pr_warn(fmt, ##__VA_ARGS__); \
+} while (0)
+
+#define AuErr1(fmt, ...) do { \
+	static unsigned char _c; \
+	if (!_c++) \
+		pr_err(fmt, ##__VA_ARGS__); \
+} while (0)
+
+#define AuIOErr1(fmt, ...) do { \
+	static unsigned char _c; \
+	if (!_c++) \
+		AuIOErr(fmt, ##__VA_ARGS__); \
+} while (0)
+
+#define AuUnsupportMsg	"This operation is not supported." \
+			" Please report this application to aufs-users ML."
+#define AuUnsupport(fmt, ...) do { \
+	pr_err(AuUnsupportMsg "\n" fmt, ##__VA_ARGS__); \
+	dump_stack(); \
+} while (0)
+
+#define AuTraceErr(e) do { \
+	if (unlikely((e) < 0)) \
+		AuDbg("err %d\n", (int)(e)); \
+} while (0)
+
+#define AuTraceErrPtr(p) do { \
+	if (IS_ERR(p)) \
+		AuDbg("err %ld\n", PTR_ERR(p)); \
+} while (0)
+
+/* dirty macros for debug print, use with "%.*s" and caution */
+#define AuLNPair(qstr)		(qstr)->len, (qstr)->name
+
+/* ---------------------------------------------------------------------- */
+
+struct dentry;
+#ifdef CONFIG_AUFS_DEBUG
+extern struct mutex au_dbg_mtx;
+extern char *au_plevel;
+struct au_nhash;
+void au_dpri_whlist(struct au_nhash *whlist);
+struct au_vdir;
+void au_dpri_vdir(struct au_vdir *vdir);
+struct inode;
+void au_dpri_inode(struct inode *inode);
+void au_dpri_dalias(struct inode *inode);
+void au_dpri_dentry(struct dentry *dentry);
+struct file;
+void au_dpri_file(struct file *filp);
+struct super_block;
+void au_dpri_sb(struct super_block *sb);
+
+#define au_dbg_verify_dinode(d) __au_dbg_verify_dinode(d, __func__, __LINE__)
+void __au_dbg_verify_dinode(struct dentry *dentry, const char *func, int line);
+void au_dbg_verify_gen(struct dentry *parent, unsigned int sigen);
+void au_dbg_verify_kthread(void);
+
+int __init au_debug_init(void);
+
+#define AuDbgWhlist(w) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#w "\n"); \
+	au_dpri_whlist(w); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgVdir(v) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#v "\n"); \
+	au_dpri_vdir(v); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgInode(i) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#i "\n"); \
+	au_dpri_inode(i); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgDAlias(i) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#i "\n"); \
+	au_dpri_dalias(i); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgDentry(d) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#d "\n"); \
+	au_dpri_dentry(d); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgFile(f) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#f "\n"); \
+	au_dpri_file(f); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgSb(sb) do { \
+	mutex_lock(&au_dbg_mtx); \
+	AuDbg(#sb "\n"); \
+	au_dpri_sb(sb); \
+	mutex_unlock(&au_dbg_mtx); \
+} while (0)
+
+#define AuDbgSym(addr) do {				\
+	char sym[KSYM_SYMBOL_LEN];			\
+	sprint_symbol(sym, (unsigned long)addr);	\
+	AuDbg("%s\n", sym);				\
+} while (0)
+#else
+AuStubVoid(au_dbg_verify_dinode, struct dentry *dentry)
+AuStubVoid(au_dbg_verify_gen, struct dentry *parent, unsigned int sigen)
+AuStubVoid(au_dbg_verify_kthread, void)
+AuStubInt0(__init au_debug_init, void)
+
+#define AuDbgWhlist(w)		do {} while (0)
+#define AuDbgVdir(v)		do {} while (0)
+#define AuDbgInode(i)		do {} while (0)
+#define AuDbgDAlias(i)		do {} while (0)
+#define AuDbgDentry(d)		do {} while (0)
+#define AuDbgFile(f)		do {} while (0)
+#define AuDbgSb(sb)		do {} while (0)
+#define AuDbgSym(addr)		do {} while (0)
+#endif /* CONFIG_AUFS_DEBUG */
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_MAGIC_SYSRQ
+int __init au_sysrq_init(void);
+void au_sysrq_fin(void);
+
+#ifdef CONFIG_HW_CONSOLE
+#define au_dbg_blocked() do { \
+	WARN_ON(1); \
+	handle_sysrq('w'); \
+} while (0)
+#else
+AuStubVoid(au_dbg_blocked, void)
+#endif
+
+#else
+AuStubInt0(__init au_sysrq_init, void)
+AuStubVoid(au_sysrq_fin, void)
+AuStubVoid(au_dbg_blocked, void)
+#endif /* CONFIG_AUFS_MAGIC_SYSRQ */
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_DEBUG_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dentry.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dentry.c
@@ -0,0 +1,1169 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * lookup and dentry operations
+ */
+
+#include <linux/iversion.h>
+#include <linux/namei.h>
+#include "aufs.h"
+
+/*
+ * returns positive/negative dentry, NULL or an error.
+ * NULL means whiteout-ed or not-found.
+ */
+static struct dentry*
+au_do_lookup(struct dentry *h_parent, struct dentry *dentry,
+	     aufs_bindex_t bindex, struct au_do_lookup_args *args)
+{
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	struct au_branch *br;
+	struct user_namespace *h_userns;
+	struct path h_path;
+	int wh_found, opq;
+	unsigned char wh_able;
+	const unsigned char allow_neg = !!au_ftest_lkup(args->flags, ALLOW_NEG);
+	const unsigned char ignore_perm = !!au_ftest_lkup(args->flags,
+							  IGNORE_PERM);
+
+	wh_found = 0;
+	br = au_sbr(dentry->d_sb, bindex);
+	h_path.dentry = h_parent;
+	h_path.mnt = au_br_mnt(br);
+	h_userns = au_br_userns(br);
+	wh_able = !!au_br_whable(br->br_perm);
+	if (wh_able)
+		wh_found = au_wh_test(h_userns, &h_path, &args->whname,
+				      ignore_perm);
+	h_dentry = ERR_PTR(wh_found);
+	if (!wh_found)
+		goto real_lookup;
+	if (unlikely(wh_found < 0))
+		goto out;
+
+	/* We found a whiteout */
+	/* au_set_dbbot(dentry, bindex); */
+	au_set_dbwh(dentry, bindex);
+	if (!allow_neg)
+		return NULL; /* success */
+
+real_lookup:
+	if (!ignore_perm)
+		h_dentry = vfsub_lkup_one(args->name, &h_path);
+	else
+		h_dentry = au_sio_lkup_one(h_userns, args->name, &h_path);
+	if (IS_ERR(h_dentry)) {
+		if (PTR_ERR(h_dentry) == -ENAMETOOLONG
+		    && !allow_neg)
+			h_dentry = NULL;
+		goto out;
+	}
+
+	h_inode = d_inode(h_dentry);
+	if (d_is_negative(h_dentry)) {
+		if (!allow_neg)
+			goto out_neg;
+	} else if (wh_found
+		   || (args->type && args->type != (h_inode->i_mode & S_IFMT)))
+		goto out_neg;
+	else if (au_ftest_lkup(args->flags, DIRREN)
+		 /* && h_inode */
+		 && !au_dr_lkup_h_ino(args, bindex, h_inode->i_ino)) {
+		AuDbg("b%d %pd ignored hi%llu\n", bindex, h_dentry,
+		      (unsigned long long)h_inode->i_ino);
+		goto out_neg;
+	}
+
+	if (au_dbbot(dentry) <= bindex)
+		au_set_dbbot(dentry, bindex);
+	if (au_dbtop(dentry) < 0 || bindex < au_dbtop(dentry))
+		au_set_dbtop(dentry, bindex);
+	au_set_h_dptr(dentry, bindex, h_dentry);
+
+	if (!d_is_dir(h_dentry)
+	    || !wh_able
+	    || (d_really_is_positive(dentry) && !d_is_dir(dentry)))
+		goto out; /* success */
+
+	h_path.dentry = h_dentry;
+	inode_lock_shared_nested(h_inode, AuLsc_I_CHILD);
+	opq = au_diropq_test(h_userns, &h_path);
+	inode_unlock_shared(h_inode);
+	if (opq > 0)
+		au_set_dbdiropq(dentry, bindex);
+	else if (unlikely(opq < 0)) {
+		au_set_h_dptr(dentry, bindex, NULL);
+		h_dentry = ERR_PTR(opq);
+	}
+	goto out;
+
+out_neg:
+	dput(h_dentry);
+	h_dentry = NULL;
+out:
+	return h_dentry;
+}
+
+static int au_test_shwh(struct super_block *sb, const struct qstr *name)
+{
+	if (unlikely(!au_opt_test(au_mntflags(sb), SHWH)
+		     && !strncmp(name->name, AUFS_WH_PFX, AUFS_WH_PFX_LEN)))
+		return -EPERM;
+	return 0;
+}
+
+/*
+ * returns the number of lower positive dentries,
+ * otherwise an error.
+ * can be called at unlinking with @type is zero.
+ */
+int au_lkup_dentry(struct dentry *dentry, aufs_bindex_t btop,
+		   unsigned int flags)
+{
+	int npositive, err;
+	aufs_bindex_t bindex, btail, bdiropq;
+	unsigned char isdir, dirperm1, dirren;
+	struct au_do_lookup_args args = {
+		.flags		= flags,
+		.name		= &dentry->d_name
+	};
+	struct dentry *parent;
+	struct super_block *sb;
+
+	sb = dentry->d_sb;
+	err = au_test_shwh(sb, args.name);
+	if (unlikely(err))
+		goto out;
+
+	err = au_wh_name_alloc(&args.whname, args.name);
+	if (unlikely(err))
+		goto out;
+
+	isdir = !!d_is_dir(dentry);
+	dirperm1 = !!au_opt_test(au_mntflags(sb), DIRPERM1);
+	dirren = !!au_opt_test(au_mntflags(sb), DIRREN);
+	if (dirren)
+		au_fset_lkup(args.flags, DIRREN);
+
+	npositive = 0;
+	parent = dget_parent(dentry);
+	btail = au_dbtaildir(parent);
+	for (bindex = btop; bindex <= btail; bindex++) {
+		struct dentry *h_parent, *h_dentry;
+		struct inode *h_inode, *h_dir;
+		struct au_branch *br;
+
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (h_dentry) {
+			if (d_is_positive(h_dentry))
+				npositive++;
+			break;
+		}
+		h_parent = au_h_dptr(parent, bindex);
+		if (!h_parent || !d_is_dir(h_parent))
+			continue;
+
+		if (dirren) {
+			/* if the inum matches, then use the prepared name */
+			err = au_dr_lkup_name(&args, bindex);
+			if (unlikely(err))
+				goto out_parent;
+		}
+
+		h_dir = d_inode(h_parent);
+		inode_lock_shared_nested(h_dir, AuLsc_I_PARENT);
+		h_dentry = au_do_lookup(h_parent, dentry, bindex, &args);
+		inode_unlock_shared(h_dir);
+		err = PTR_ERR(h_dentry);
+		if (IS_ERR(h_dentry))
+			goto out_parent;
+		if (h_dentry)
+			au_fclr_lkup(args.flags, ALLOW_NEG);
+		if (dirperm1)
+			au_fset_lkup(args.flags, IGNORE_PERM);
+
+		if (au_dbwh(dentry) == bindex)
+			break;
+		if (!h_dentry)
+			continue;
+		if (d_is_negative(h_dentry))
+			continue;
+		h_inode = d_inode(h_dentry);
+		npositive++;
+		if (!args.type)
+			args.type = h_inode->i_mode & S_IFMT;
+		if (args.type != S_IFDIR)
+			break;
+		else if (isdir) {
+			/* the type of lower may be different */
+			bdiropq = au_dbdiropq(dentry);
+			if (bdiropq >= 0 && bdiropq <= bindex)
+				break;
+		}
+		br = au_sbr(sb, bindex);
+		if (dirren
+		    && au_dr_hino_test_add(&br->br_dirren, h_inode->i_ino,
+					   /*add_ent*/NULL)) {
+			/* prepare next name to lookup */
+			err = au_dr_lkup(&args, dentry, bindex);
+			if (unlikely(err))
+				goto out_parent;
+		}
+	}
+
+	if (npositive) {
+		AuLabel(positive);
+		au_update_dbtop(dentry);
+	}
+	err = npositive;
+	if (unlikely(!au_opt_test(au_mntflags(sb), UDBA_NONE)
+		     && au_dbtop(dentry) < 0)) {
+		err = -EIO;
+		AuIOErr("both of real entry and whiteout found, %pd, err %d\n",
+			dentry, err);
+	}
+
+out_parent:
+	dput(parent);
+	au_kfree_try_rcu(args.whname.name);
+	if (dirren)
+		au_dr_lkup_fin(&args);
+out:
+	return err;
+}
+
+struct dentry *au_sio_lkup_one(struct user_namespace *userns, struct qstr *name,
+			       struct path *ppath)
+{
+	struct dentry *dentry;
+	int wkq_err;
+
+	if (!au_test_h_perm_sio(userns, d_inode(ppath->dentry), MAY_EXEC))
+		dentry = vfsub_lkup_one(name, ppath);
+	else {
+		struct vfsub_lkup_one_args args = {
+			.errp	= &dentry,
+			.name	= name,
+			.ppath	= ppath
+		};
+
+		wkq_err = au_wkq_wait(vfsub_call_lkup_one, &args);
+		if (unlikely(wkq_err))
+			dentry = ERR_PTR(wkq_err);
+	}
+
+	return dentry;
+}
+
+/*
+ * lookup @dentry on @bindex which should be negative.
+ */
+int au_lkup_neg(struct dentry *dentry, aufs_bindex_t bindex, int wh)
+{
+	int err;
+	struct dentry *parent, *h_dentry;
+	struct au_branch *br;
+	struct user_namespace *h_userns;
+	struct path h_ppath;
+
+	parent = dget_parent(dentry);
+	br = au_sbr(dentry->d_sb, bindex);
+	h_ppath.dentry = au_h_dptr(parent, bindex);
+	h_ppath.mnt = au_br_mnt(br);
+	h_userns = au_br_userns(br);
+	if (wh)
+		h_dentry = au_whtmp_lkup(h_ppath.dentry, br, &dentry->d_name);
+	else
+		h_dentry = au_sio_lkup_one(h_userns, &dentry->d_name, &h_ppath);
+	err = PTR_ERR(h_dentry);
+	if (IS_ERR(h_dentry))
+		goto out;
+	if (unlikely(d_is_positive(h_dentry))) {
+		err = -EIO;
+		AuIOErr("%pd should be negative on b%d.\n", h_dentry, bindex);
+		dput(h_dentry);
+		goto out;
+	}
+
+	err = 0;
+	if (bindex < au_dbtop(dentry))
+		au_set_dbtop(dentry, bindex);
+	if (au_dbbot(dentry) < bindex)
+		au_set_dbbot(dentry, bindex);
+	au_set_h_dptr(dentry, bindex, h_dentry);
+
+out:
+	dput(parent);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* subset of struct inode */
+struct au_iattr {
+	unsigned long		i_ino;
+	/* unsigned int		i_nlink; */
+	kuid_t			i_uid;
+	kgid_t			i_gid;
+	u64			i_version;
+/*
+	loff_t			i_size;
+	blkcnt_t		i_blocks;
+*/
+	umode_t			i_mode;
+};
+
+static void au_iattr_save(struct au_iattr *ia, struct inode *h_inode)
+{
+	ia->i_ino = h_inode->i_ino;
+	/* ia->i_nlink = h_inode->i_nlink; */
+	ia->i_uid = h_inode->i_uid;
+	ia->i_gid = h_inode->i_gid;
+	ia->i_version = inode_query_iversion(h_inode);
+/*
+	ia->i_size = h_inode->i_size;
+	ia->i_blocks = h_inode->i_blocks;
+*/
+	ia->i_mode = (h_inode->i_mode & S_IFMT);
+}
+
+static int au_iattr_test(struct au_iattr *ia, struct inode *h_inode)
+{
+	return ia->i_ino != h_inode->i_ino
+		/* || ia->i_nlink != h_inode->i_nlink */
+		|| !uid_eq(ia->i_uid, h_inode->i_uid)
+		|| !gid_eq(ia->i_gid, h_inode->i_gid)
+		|| !inode_eq_iversion(h_inode, ia->i_version)
+/*
+		|| ia->i_size != h_inode->i_size
+		|| ia->i_blocks != h_inode->i_blocks
+*/
+		|| ia->i_mode != (h_inode->i_mode & S_IFMT);
+}
+
+static int au_h_verify_dentry(struct dentry *h_dentry, struct dentry *h_parent,
+			      struct au_branch *br)
+{
+	int err;
+	struct au_iattr ia;
+	struct inode *h_inode;
+	struct dentry *h_d;
+	struct super_block *h_sb;
+	struct path h_ppath;
+
+	err = 0;
+	memset(&ia, -1, sizeof(ia));
+	h_sb = h_dentry->d_sb;
+	h_inode = NULL;
+	if (d_is_positive(h_dentry)) {
+		h_inode = d_inode(h_dentry);
+		au_iattr_save(&ia, h_inode);
+	} else if (au_test_nfs(h_sb) || au_test_fuse(h_sb))
+		/* nfs d_revalidate may return 0 for negative dentry */
+		/* fuse d_revalidate always return 0 for negative dentry */
+		goto out;
+
+	/* main purpose is namei.c:cached_lookup() and d_revalidate */
+	h_ppath.dentry = h_parent;
+	h_ppath.mnt = au_br_mnt(br);
+	h_d = vfsub_lkup_one(&h_dentry->d_name, &h_ppath);
+	err = PTR_ERR(h_d);
+	if (IS_ERR(h_d))
+		goto out;
+
+	err = 0;
+	if (unlikely(h_d != h_dentry
+		     || d_inode(h_d) != h_inode
+		     || (h_inode && au_iattr_test(&ia, h_inode))))
+		err = au_busy_or_stale();
+	dput(h_d);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_h_verify(struct dentry *h_dentry, unsigned int udba, struct inode *h_dir,
+		struct dentry *h_parent, struct au_branch *br)
+{
+	int err;
+
+	err = 0;
+	if (udba == AuOpt_UDBA_REVAL
+	    && !au_test_fs_remote(h_dentry->d_sb)) {
+		IMustLock(h_dir);
+		err = (d_inode(h_dentry->d_parent) != h_dir);
+	} else if (udba != AuOpt_UDBA_NONE)
+		err = au_h_verify_dentry(h_dentry, h_parent, br);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_do_refresh_hdentry(struct dentry *dentry, struct dentry *parent)
+{
+	int err;
+	aufs_bindex_t new_bindex, bindex, bbot, bwh, bdiropq;
+	struct au_hdentry tmp, *p, *q;
+	struct au_dinfo *dinfo;
+	struct super_block *sb;
+
+	DiMustWriteLock(dentry);
+
+	sb = dentry->d_sb;
+	dinfo = au_di(dentry);
+	bbot = dinfo->di_bbot;
+	bwh = dinfo->di_bwh;
+	bdiropq = dinfo->di_bdiropq;
+	bindex = dinfo->di_btop;
+	p = au_hdentry(dinfo, bindex);
+	for (; bindex <= bbot; bindex++, p++) {
+		if (!p->hd_dentry)
+			continue;
+
+		new_bindex = au_br_index(sb, p->hd_id);
+		if (new_bindex == bindex)
+			continue;
+
+		if (dinfo->di_bwh == bindex)
+			bwh = new_bindex;
+		if (dinfo->di_bdiropq == bindex)
+			bdiropq = new_bindex;
+		if (new_bindex < 0) {
+			au_hdput(p);
+			p->hd_dentry = NULL;
+			continue;
+		}
+
+		/* swap two lower dentries, and loop again */
+		q = au_hdentry(dinfo, new_bindex);
+		tmp = *q;
+		*q = *p;
+		*p = tmp;
+		if (tmp.hd_dentry) {
+			bindex--;
+			p--;
+		}
+	}
+
+	dinfo->di_bwh = -1;
+	if (bwh >= 0 && bwh <= au_sbbot(sb) && au_sbr_whable(sb, bwh))
+		dinfo->di_bwh = bwh;
+
+	dinfo->di_bdiropq = -1;
+	if (bdiropq >= 0
+	    && bdiropq <= au_sbbot(sb)
+	    && au_sbr_whable(sb, bdiropq))
+		dinfo->di_bdiropq = bdiropq;
+
+	err = -EIO;
+	dinfo->di_btop = -1;
+	dinfo->di_bbot = -1;
+	bbot = au_dbbot(parent);
+	bindex = 0;
+	p = au_hdentry(dinfo, bindex);
+	for (; bindex <= bbot; bindex++, p++)
+		if (p->hd_dentry) {
+			dinfo->di_btop = bindex;
+			break;
+		}
+
+	if (dinfo->di_btop >= 0) {
+		bindex = bbot;
+		p = au_hdentry(dinfo, bindex);
+		for (; bindex >= 0; bindex--, p--)
+			if (p->hd_dentry) {
+				dinfo->di_bbot = bindex;
+				err = 0;
+				break;
+			}
+	}
+
+	return err;
+}
+
+static void au_do_hide(struct dentry *dentry)
+{
+	struct inode *inode;
+
+	if (d_really_is_positive(dentry)) {
+		inode = d_inode(dentry);
+		if (!d_is_dir(dentry)) {
+			if (inode->i_nlink && !d_unhashed(dentry))
+				drop_nlink(inode);
+		} else {
+			clear_nlink(inode);
+			/* stop next lookup */
+			inode->i_flags |= S_DEAD;
+		}
+		smp_mb(); /* necessary? */
+	}
+	d_drop(dentry);
+}
+
+static int au_hide_children(struct dentry *parent)
+{
+	int err, i, j, ndentry;
+	struct au_dcsub_pages dpages;
+	struct au_dpage *dpage;
+	struct dentry *dentry;
+
+	err = au_dpages_init(&dpages, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+	err = au_dcsub_pages(&dpages, parent, NULL, NULL);
+	if (unlikely(err))
+		goto out_dpages;
+
+	/* in reverse order */
+	for (i = dpages.ndpage - 1; i >= 0; i--) {
+		dpage = dpages.dpages + i;
+		ndentry = dpage->ndentry;
+		for (j = ndentry - 1; j >= 0; j--) {
+			dentry = dpage->dentries[j];
+			if (dentry != parent)
+				au_do_hide(dentry);
+		}
+	}
+
+out_dpages:
+	au_dpages_free(&dpages);
+out:
+	return err;
+}
+
+static void au_hide(struct dentry *dentry)
+{
+	int err;
+
+	AuDbgDentry(dentry);
+	if (d_is_dir(dentry)) {
+		/* shrink_dcache_parent(dentry); */
+		err = au_hide_children(dentry);
+		if (unlikely(err))
+			AuIOErr("%pd, failed hiding children, ignored %d\n",
+				dentry, err);
+	}
+	au_do_hide(dentry);
+}
+
+/*
+ * By adding a dirty branch, a cached dentry may be affected in various ways.
+ *
+ * a dirty branch is added
+ * - on the top of layers
+ * - in the middle of layers
+ * - to the bottom of layers
+ *
+ * on the added branch there exists
+ * - a whiteout
+ * - a diropq
+ * - a same named entry
+ *   + exist
+ *     * negative --> positive
+ *     * positive --> positive
+ *	 - type is unchanged
+ *	 - type is changed
+ *   + doesn't exist
+ *     * negative --> negative
+ *     * positive --> negative (rejected by au_br_del() for non-dir case)
+ * - none
+ */
+static int au_refresh_by_dinfo(struct dentry *dentry, struct au_dinfo *dinfo,
+			       struct au_dinfo *tmp)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct {
+		struct dentry *dentry;
+		struct inode *inode;
+		mode_t mode;
+	} orig_h, tmp_h = {
+		.dentry = NULL
+	};
+	struct au_hdentry *hd;
+	struct inode *inode, *h_inode;
+	struct dentry *h_dentry;
+
+	err = 0;
+	AuDebugOn(dinfo->di_btop < 0);
+	orig_h.mode = 0;
+	orig_h.dentry = au_hdentry(dinfo, dinfo->di_btop)->hd_dentry;
+	orig_h.inode = NULL;
+	if (d_is_positive(orig_h.dentry)) {
+		orig_h.inode = d_inode(orig_h.dentry);
+		orig_h.mode = orig_h.inode->i_mode & S_IFMT;
+	}
+	if (tmp->di_btop >= 0) {
+		tmp_h.dentry = au_hdentry(tmp, tmp->di_btop)->hd_dentry;
+		if (d_is_positive(tmp_h.dentry)) {
+			tmp_h.inode = d_inode(tmp_h.dentry);
+			tmp_h.mode = tmp_h.inode->i_mode & S_IFMT;
+		}
+	}
+
+	inode = NULL;
+	if (d_really_is_positive(dentry))
+		inode = d_inode(dentry);
+	if (!orig_h.inode) {
+		AuDbg("negative originally\n");
+		if (inode) {
+			au_hide(dentry);
+			goto out;
+		}
+		AuDebugOn(inode);
+		AuDebugOn(dinfo->di_btop != dinfo->di_bbot);
+		AuDebugOn(dinfo->di_bdiropq != -1);
+
+		if (!tmp_h.inode) {
+			AuDbg("negative --> negative\n");
+			/* should have only one negative lower */
+			if (tmp->di_btop >= 0
+			    && tmp->di_btop < dinfo->di_btop) {
+				AuDebugOn(tmp->di_btop != tmp->di_bbot);
+				AuDebugOn(dinfo->di_btop != dinfo->di_bbot);
+				au_set_h_dptr(dentry, dinfo->di_btop, NULL);
+				au_di_cp(dinfo, tmp);
+				hd = au_hdentry(tmp, tmp->di_btop);
+				au_set_h_dptr(dentry, tmp->di_btop,
+					      dget(hd->hd_dentry));
+			}
+			au_dbg_verify_dinode(dentry);
+		} else {
+			AuDbg("negative --> positive\n");
+			/*
+			 * similar to the behaviour of creating with bypassing
+			 * aufs.
+			 * unhash it in order to force an error in the
+			 * succeeding create operation.
+			 * we should not set S_DEAD here.
+			 */
+			d_drop(dentry);
+			/* au_di_swap(tmp, dinfo); */
+			au_dbg_verify_dinode(dentry);
+		}
+	} else {
+		AuDbg("positive originally\n");
+		/* inode may be NULL */
+		AuDebugOn(inode && (inode->i_mode & S_IFMT) != orig_h.mode);
+		if (!tmp_h.inode) {
+			AuDbg("positive --> negative\n");
+			/* or bypassing aufs */
+			au_hide(dentry);
+			if (tmp->di_bwh >= 0 && tmp->di_bwh <= dinfo->di_btop)
+				dinfo->di_bwh = tmp->di_bwh;
+			if (inode)
+				err = au_refresh_hinode_self(inode);
+			au_dbg_verify_dinode(dentry);
+		} else if (orig_h.mode == tmp_h.mode) {
+			AuDbg("positive --> positive, same type\n");
+			if (!S_ISDIR(orig_h.mode)
+			    && dinfo->di_btop > tmp->di_btop) {
+				/*
+				 * similar to the behaviour of removing and
+				 * creating.
+				 */
+				au_hide(dentry);
+				if (inode)
+					err = au_refresh_hinode_self(inode);
+				au_dbg_verify_dinode(dentry);
+			} else {
+				/* fill empty slots */
+				if (dinfo->di_btop > tmp->di_btop)
+					dinfo->di_btop = tmp->di_btop;
+				if (dinfo->di_bbot < tmp->di_bbot)
+					dinfo->di_bbot = tmp->di_bbot;
+				dinfo->di_bwh = tmp->di_bwh;
+				dinfo->di_bdiropq = tmp->di_bdiropq;
+				bbot = dinfo->di_bbot;
+				bindex = tmp->di_btop;
+				hd = au_hdentry(tmp, bindex);
+				for (; bindex <= bbot; bindex++, hd++) {
+					if (au_h_dptr(dentry, bindex))
+						continue;
+					h_dentry = hd->hd_dentry;
+					if (!h_dentry)
+						continue;
+					AuDebugOn(d_is_negative(h_dentry));
+					h_inode = d_inode(h_dentry);
+					AuDebugOn(orig_h.mode
+						  != (h_inode->i_mode
+						      & S_IFMT));
+					au_set_h_dptr(dentry, bindex,
+						      dget(h_dentry));
+				}
+				if (inode)
+					err = au_refresh_hinode(inode, dentry);
+				au_dbg_verify_dinode(dentry);
+			}
+		} else {
+			AuDbg("positive --> positive, different type\n");
+			/* similar to the behaviour of removing and creating */
+			au_hide(dentry);
+			if (inode)
+				err = au_refresh_hinode_self(inode);
+			au_dbg_verify_dinode(dentry);
+		}
+	}
+
+out:
+	return err;
+}
+
+void au_refresh_dop(struct dentry *dentry, int force_reval)
+{
+	const struct dentry_operations *dop
+		= force_reval ? &aufs_dop : dentry->d_sb->s_d_op;
+	static const unsigned int mask
+		= DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE;
+
+	BUILD_BUG_ON(sizeof(mask) != sizeof(dentry->d_flags));
+
+	if (dentry->d_op == dop)
+		return;
+
+	AuDbg("%pd\n", dentry);
+	spin_lock(&dentry->d_lock);
+	if (dop == &aufs_dop)
+		dentry->d_flags |= mask;
+	else
+		dentry->d_flags &= ~mask;
+	dentry->d_op = dop;
+	spin_unlock(&dentry->d_lock);
+}
+
+int au_refresh_dentry(struct dentry *dentry, struct dentry *parent)
+{
+	int err, ebrange, nbr;
+	unsigned int sigen;
+	struct au_dinfo *dinfo, *tmp;
+	struct super_block *sb;
+	struct inode *inode;
+
+	DiMustWriteLock(dentry);
+	AuDebugOn(IS_ROOT(dentry));
+	AuDebugOn(d_really_is_negative(parent));
+
+	sb = dentry->d_sb;
+	sigen = au_sigen(sb);
+	err = au_digen_test(parent, sigen);
+	if (unlikely(err))
+		goto out;
+
+	nbr = au_sbbot(sb) + 1;
+	dinfo = au_di(dentry);
+	err = au_di_realloc(dinfo, nbr, /*may_shrink*/0);
+	if (unlikely(err))
+		goto out;
+	ebrange = au_dbrange_test(dentry);
+	if (!ebrange)
+		ebrange = au_do_refresh_hdentry(dentry, parent);
+
+	if (d_unhashed(dentry) || ebrange /* || dinfo->di_tmpfile */) {
+		AuDebugOn(au_dbtop(dentry) < 0 && au_dbbot(dentry) >= 0);
+		if (d_really_is_positive(dentry)) {
+			inode = d_inode(dentry);
+			err = au_refresh_hinode_self(inode);
+		}
+		au_dbg_verify_dinode(dentry);
+		if (!err)
+			goto out_dgen; /* success */
+		goto out;
+	}
+
+	/* temporary dinfo */
+	AuDbgDentry(dentry);
+	err = -ENOMEM;
+	tmp = au_di_alloc(sb, AuLsc_DI_TMP);
+	if (unlikely(!tmp))
+		goto out;
+	au_di_swap(tmp, dinfo);
+	/* returns the number of positive dentries */
+	/*
+	 * if current working dir is removed, it returns an error.
+	 * but the dentry is legal.
+	 */
+	err = au_lkup_dentry(dentry, /*btop*/0, AuLkup_ALLOW_NEG);
+	AuDbgDentry(dentry);
+	au_di_swap(tmp, dinfo);
+	if (err == -ENOENT)
+		err = 0;
+	if (err >= 0) {
+		/* compare/refresh by dinfo */
+		AuDbgDentry(dentry);
+		err = au_refresh_by_dinfo(dentry, dinfo, tmp);
+		au_dbg_verify_dinode(dentry);
+		AuTraceErr(err);
+	}
+	au_di_realloc(dinfo, nbr, /*may_shrink*/1); /* harmless if err */
+	au_rw_write_unlock(&tmp->di_rwsem);
+	au_di_free(tmp);
+	if (unlikely(err))
+		goto out;
+
+out_dgen:
+	au_update_digen(dentry);
+out:
+	if (unlikely(err && !(dentry->d_flags & DCACHE_NFSFS_RENAMED))) {
+		AuIOErr("failed refreshing %pd, %d\n", dentry, err);
+		AuDbgDentry(dentry);
+	}
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_do_h_d_reval(struct dentry *h_dentry, unsigned int flags,
+			   struct dentry *dentry, aufs_bindex_t bindex)
+{
+	int err, valid;
+
+	err = 0;
+	if (!(h_dentry->d_flags & DCACHE_OP_REVALIDATE))
+		goto out;
+
+	AuDbg("b%d\n", bindex);
+	/*
+	 * gave up supporting LOOKUP_CREATE/OPEN for lower fs,
+	 * due to whiteout and branch permission.
+	 */
+	flags &= ~(/*LOOKUP_PARENT |*/ LOOKUP_OPEN | LOOKUP_CREATE
+		   | LOOKUP_FOLLOW | LOOKUP_EXCL);
+	/* it may return tri-state */
+	valid = h_dentry->d_op->d_revalidate(h_dentry, flags);
+
+	if (unlikely(valid < 0))
+		err = valid;
+	else if (!valid)
+		err = -EINVAL;
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* todo: remove this */
+static int h_d_revalidate(struct dentry *dentry, struct inode *inode,
+			  unsigned int flags, int do_udba, int dirren)
+{
+	int err;
+	umode_t mode, h_mode;
+	aufs_bindex_t bindex, btail, btop, ibs, ibe;
+	unsigned char plus, unhashed, is_root, h_plus, h_nfs, tmpfile;
+	struct inode *h_inode, *h_cached_inode;
+	struct dentry *h_dentry;
+	struct qstr *name, *h_name;
+
+	err = 0;
+	plus = 0;
+	mode = 0;
+	ibs = -1;
+	ibe = -1;
+	unhashed = !!d_unhashed(dentry);
+	is_root = !!IS_ROOT(dentry);
+	name = &dentry->d_name;
+	tmpfile = au_di(dentry)->di_tmpfile;
+
+	/*
+	 * Theoretically, REVAL test should be unnecessary in case of
+	 * {FS,I}NOTIFY.
+	 * But {fs,i}notify doesn't fire some necessary events,
+	 *	IN_ATTRIB for atime/nlink/pageio
+	 * Let's do REVAL test too.
+	 */
+	if (do_udba && inode) {
+		mode = (inode->i_mode & S_IFMT);
+		plus = (inode->i_nlink > 0);
+		ibs = au_ibtop(inode);
+		ibe = au_ibbot(inode);
+	}
+
+	btop = au_dbtop(dentry);
+	btail = btop;
+	if (inode && S_ISDIR(inode->i_mode))
+		btail = au_dbtaildir(dentry);
+	for (bindex = btop; bindex <= btail; bindex++) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (!h_dentry)
+			continue;
+
+		AuDbg("b%d, %pd\n", bindex, h_dentry);
+		h_nfs = !!au_test_nfs(h_dentry->d_sb);
+		spin_lock(&h_dentry->d_lock);
+		h_name = &h_dentry->d_name;
+		if (unlikely(do_udba
+			     && !is_root
+			     && ((!h_nfs
+				  && (unhashed != !!d_unhashed(h_dentry)
+				      || (!tmpfile && !dirren
+					  && !au_qstreq(name, h_name))
+					  ))
+				 || (h_nfs
+				     && !(flags & LOOKUP_OPEN)
+				     && (h_dentry->d_flags
+					 & DCACHE_NFSFS_RENAMED)))
+			    )) {
+			int h_unhashed;
+
+			h_unhashed = d_unhashed(h_dentry);
+			spin_unlock(&h_dentry->d_lock);
+			AuDbg("unhash 0x%x 0x%x, %pd %pd\n",
+			      unhashed, h_unhashed, dentry, h_dentry);
+			goto err;
+		}
+		spin_unlock(&h_dentry->d_lock);
+
+		err = au_do_h_d_reval(h_dentry, flags, dentry, bindex);
+		if (unlikely(err))
+			/* do not goto err, to keep the errno */
+			break;
+
+		/* todo: plink too? */
+		if (!do_udba)
+			continue;
+
+		/* UDBA tests */
+		if (unlikely(!!inode != d_is_positive(h_dentry)))
+			goto err;
+
+		h_inode = NULL;
+		if (d_is_positive(h_dentry))
+			h_inode = d_inode(h_dentry);
+		h_plus = plus;
+		h_mode = mode;
+		h_cached_inode = h_inode;
+		if (h_inode) {
+			h_mode = (h_inode->i_mode & S_IFMT);
+			h_plus = (h_inode->i_nlink > 0);
+		}
+		if (inode && ibs <= bindex && bindex <= ibe)
+			h_cached_inode = au_h_iptr(inode, bindex);
+
+		if (!h_nfs) {
+			if (unlikely(plus != h_plus && !tmpfile))
+				goto err;
+		} else {
+			if (unlikely(!(h_dentry->d_flags & DCACHE_NFSFS_RENAMED)
+				     && !is_root
+				     && !IS_ROOT(h_dentry)
+				     && unhashed != d_unhashed(h_dentry)))
+				goto err;
+		}
+		if (unlikely(mode != h_mode
+			     || h_cached_inode != h_inode))
+			goto err;
+		continue;
+
+err:
+		err = -EINVAL;
+		break;
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+/* todo: consolidate with do_refresh() and au_reval_for_attr() */
+static int simple_reval_dpath(struct dentry *dentry, unsigned int sigen)
+{
+	int err;
+	struct dentry *parent;
+
+	if (!au_digen_test(dentry, sigen))
+		return 0;
+
+	parent = dget_parent(dentry);
+	di_read_lock_parent(parent, AuLock_IR);
+	AuDebugOn(au_digen_test(parent, sigen));
+	au_dbg_verify_gen(parent, sigen);
+	err = au_refresh_dentry(dentry, parent);
+	di_read_unlock(parent, AuLock_IR);
+	dput(parent);
+	AuTraceErr(err);
+	return err;
+}
+
+int au_reval_dpath(struct dentry *dentry, unsigned int sigen)
+{
+	int err;
+	struct dentry *d, *parent;
+
+	if (!au_ftest_si(au_sbi(dentry->d_sb), FAILED_REFRESH_DIR))
+		return simple_reval_dpath(dentry, sigen);
+
+	/* slow loop, keep it simple and stupid */
+	/* cf: au_cpup_dirs() */
+	err = 0;
+	parent = NULL;
+	while (au_digen_test(dentry, sigen)) {
+		d = dentry;
+		while (1) {
+			dput(parent);
+			parent = dget_parent(d);
+			if (!au_digen_test(parent, sigen))
+				break;
+			d = parent;
+		}
+
+		if (d != dentry)
+			di_write_lock_child2(d);
+
+		/* someone might update our dentry while we were sleeping */
+		if (au_digen_test(d, sigen)) {
+			/*
+			 * todo: consolidate with simple_reval_dpath(),
+			 * do_refresh() and au_reval_for_attr().
+			 */
+			di_read_lock_parent(parent, AuLock_IR);
+			err = au_refresh_dentry(d, parent);
+			di_read_unlock(parent, AuLock_IR);
+		}
+
+		if (d != dentry)
+			di_write_unlock(d);
+		dput(parent);
+		if (unlikely(err))
+			break;
+	}
+
+	return err;
+}
+
+/*
+ * if valid returns 1, otherwise 0.
+ */
+static int aufs_d_revalidate(struct dentry *dentry, unsigned int flags)
+{
+	int valid, err;
+	unsigned int sigen;
+	unsigned char do_udba, dirren;
+	struct super_block *sb;
+	struct inode *inode;
+
+	/* todo: support rcu-walk? */
+	if (flags & LOOKUP_RCU)
+		return -ECHILD;
+
+	valid = 0;
+	if (unlikely(!au_di(dentry)))
+		goto out;
+
+	valid = 1;
+	sb = dentry->d_sb;
+	/*
+	 * todo: very ugly
+	 * i_mutex of parent dir may be held,
+	 * but we should not return 'invalid' due to busy.
+	 */
+	err = aufs_read_lock(dentry, AuLock_FLUSH | AuLock_DW | AuLock_NOPLM);
+	if (unlikely(err)) {
+		valid = err;
+		AuTraceErr(err);
+		goto out;
+	}
+	inode = NULL;
+	if (d_really_is_positive(dentry))
+		inode = d_inode(dentry);
+	if (unlikely(inode && au_is_bad_inode(inode))) {
+		err = -EINVAL;
+		AuTraceErr(err);
+		goto out_dgrade;
+	}
+	if (unlikely(au_dbrange_test(dentry))) {
+		err = -EINVAL;
+		AuTraceErr(err);
+		goto out_dgrade;
+	}
+
+	sigen = au_sigen(sb);
+	if (au_digen_test(dentry, sigen)) {
+		AuDebugOn(IS_ROOT(dentry));
+		err = au_reval_dpath(dentry, sigen);
+		if (unlikely(err)) {
+			AuTraceErr(err);
+			goto out_dgrade;
+		}
+	}
+	di_downgrade_lock(dentry, AuLock_IR);
+
+	err = -EINVAL;
+	if (!(flags & (LOOKUP_OPEN | LOOKUP_EMPTY))
+	    && inode
+	    && !(inode->i_state && I_LINKABLE)
+	    && (IS_DEADDIR(inode) || !inode->i_nlink)) {
+		AuTraceErr(err);
+		goto out_inval;
+	}
+
+	do_udba = !au_opt_test(au_mntflags(sb), UDBA_NONE);
+	if (do_udba && inode) {
+		aufs_bindex_t btop = au_ibtop(inode);
+		struct inode *h_inode;
+
+		if (btop >= 0) {
+			h_inode = au_h_iptr(inode, btop);
+			if (h_inode && au_test_higen(inode, h_inode)) {
+				AuTraceErr(err);
+				goto out_inval;
+			}
+		}
+	}
+
+	dirren = !!au_opt_test(au_mntflags(sb), DIRREN);
+	err = h_d_revalidate(dentry, inode, flags, do_udba, dirren);
+	if (unlikely(!err && do_udba && au_dbtop(dentry) < 0)) {
+		err = -EIO;
+		AuDbg("both of real entry and whiteout found, %p, err %d\n",
+		      dentry, err);
+	}
+	goto out_inval;
+
+out_dgrade:
+	di_downgrade_lock(dentry, AuLock_IR);
+out_inval:
+	aufs_read_unlock(dentry, AuLock_IR);
+	AuTraceErr(err);
+	valid = !err;
+out:
+	if (!valid) {
+		AuDbg("%pd invalid, %d\n", dentry, valid);
+		d_drop(dentry);
+	}
+	return valid;
+}
+
+static void aufs_d_release(struct dentry *dentry)
+{
+	if (au_di(dentry)) {
+		au_di_fin(dentry);
+		au_hn_di_reinit(dentry);
+	}
+}
+
+const struct dentry_operations aufs_dop = {
+	.d_revalidate		= aufs_d_revalidate,
+	.d_weak_revalidate	= aufs_d_revalidate,
+	.d_release		= aufs_d_release
+};
+
+/* aufs_dop without d_revalidate */
+const struct dentry_operations aufs_dop_noreval = {
+	.d_release		= aufs_d_release
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dentry.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dentry.h
@@ -0,0 +1,269 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * lookup and dentry operations
+ */
+
+#ifndef __AUFS_DENTRY_H__
+#define __AUFS_DENTRY_H__
+
+#ifdef __KERNEL__
+
+#include <linux/dcache.h>
+#include "dirren.h"
+#include "rwsem.h"
+
+struct au_hdentry {
+	struct dentry		*hd_dentry;
+	aufs_bindex_t		hd_id;
+};
+
+struct au_dinfo {
+	atomic_t		di_generation;
+
+	struct au_rwsem		di_rwsem;
+	aufs_bindex_t		di_btop, di_bbot, di_bwh, di_bdiropq;
+	unsigned char		di_tmpfile; /* to allow the different name */
+	struct au_hdentry	*di_hdentry;
+	struct rcu_head		rcu;
+} ____cacheline_aligned_in_smp;
+
+/* ---------------------------------------------------------------------- */
+
+/* flags for au_lkup_dentry() */
+#define AuLkup_ALLOW_NEG	1
+#define AuLkup_IGNORE_PERM	(1 << 1)
+#define AuLkup_DIRREN		(1 << 2)
+#define au_ftest_lkup(flags, name)	((flags) & AuLkup_##name)
+#define au_fset_lkup(flags, name) \
+	do { (flags) |= AuLkup_##name; } while (0)
+#define au_fclr_lkup(flags, name) \
+	do { (flags) &= ~AuLkup_##name; } while (0)
+
+#ifndef CONFIG_AUFS_DIRREN
+#undef AuLkup_DIRREN
+#define AuLkup_DIRREN 0
+#endif
+
+struct au_do_lookup_args {
+	unsigned int		flags;
+	mode_t			type;
+	struct qstr		whname, *name;
+	struct au_dr_lookup	dirren;
+};
+
+/* ---------------------------------------------------------------------- */
+
+/* dentry.c */
+extern const struct dentry_operations aufs_dop, aufs_dop_noreval;
+struct au_branch;
+struct dentry *au_sio_lkup_one(struct user_namespace *userns, struct qstr *name,
+			       struct path *ppath);
+int au_h_verify(struct dentry *h_dentry, unsigned int udba, struct inode *h_dir,
+		struct dentry *h_parent, struct au_branch *br);
+
+int au_lkup_dentry(struct dentry *dentry, aufs_bindex_t btop,
+		   unsigned int flags);
+int au_lkup_neg(struct dentry *dentry, aufs_bindex_t bindex, int wh);
+int au_refresh_dentry(struct dentry *dentry, struct dentry *parent);
+int au_reval_dpath(struct dentry *dentry, unsigned int sigen);
+void au_refresh_dop(struct dentry *dentry, int force_reval);
+
+/* dinfo.c */
+void au_di_init_once(void *_di);
+struct au_dinfo *au_di_alloc(struct super_block *sb, unsigned int lsc);
+void au_di_free(struct au_dinfo *dinfo);
+void au_di_swap(struct au_dinfo *a, struct au_dinfo *b);
+void au_di_cp(struct au_dinfo *dst, struct au_dinfo *src);
+int au_di_init(struct dentry *dentry);
+void au_di_fin(struct dentry *dentry);
+int au_di_realloc(struct au_dinfo *dinfo, int nbr, int may_shrink);
+
+void di_read_lock(struct dentry *d, int flags, unsigned int lsc);
+void di_read_unlock(struct dentry *d, int flags);
+void di_downgrade_lock(struct dentry *d, int flags);
+void di_write_lock(struct dentry *d, unsigned int lsc);
+void di_write_unlock(struct dentry *d);
+void di_write_lock2_child(struct dentry *d1, struct dentry *d2, int isdir);
+void di_write_lock2_parent(struct dentry *d1, struct dentry *d2, int isdir);
+void di_write_unlock2(struct dentry *d1, struct dentry *d2);
+
+struct dentry *au_h_dptr(struct dentry *dentry, aufs_bindex_t bindex);
+struct dentry *au_h_d_alias(struct dentry *dentry, aufs_bindex_t bindex);
+aufs_bindex_t au_dbtail(struct dentry *dentry);
+aufs_bindex_t au_dbtaildir(struct dentry *dentry);
+
+void au_set_h_dptr(struct dentry *dentry, aufs_bindex_t bindex,
+		   struct dentry *h_dentry);
+int au_digen_test(struct dentry *dentry, unsigned int sigen);
+int au_dbrange_test(struct dentry *dentry);
+void au_update_digen(struct dentry *dentry);
+void au_update_dbrange(struct dentry *dentry, int do_put_zero);
+void au_update_dbtop(struct dentry *dentry);
+void au_update_dbbot(struct dentry *dentry);
+int au_find_dbindex(struct dentry *dentry, struct dentry *h_dentry);
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct au_dinfo *au_di(struct dentry *dentry)
+{
+	return dentry->d_fsdata;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* lock subclass for dinfo */
+enum {
+	AuLsc_DI_CHILD,		/* child first */
+	AuLsc_DI_CHILD2,	/* rename(2), link(2), and cpup at hnotify */
+	AuLsc_DI_CHILD3,	/* copyup dirs */
+	AuLsc_DI_PARENT,
+	AuLsc_DI_PARENT2,
+	AuLsc_DI_PARENT3,
+	AuLsc_DI_TMP		/* temp for replacing dinfo */
+};
+
+/*
+ * di_read_lock_child, di_write_lock_child,
+ * di_read_lock_child2, di_write_lock_child2,
+ * di_read_lock_child3, di_write_lock_child3,
+ * di_read_lock_parent, di_write_lock_parent,
+ * di_read_lock_parent2, di_write_lock_parent2,
+ * di_read_lock_parent3, di_write_lock_parent3,
+ */
+#define AuReadLockFunc(name, lsc) \
+static inline void di_read_lock_##name(struct dentry *d, int flags) \
+{ di_read_lock(d, flags, AuLsc_DI_##lsc); }
+
+#define AuWriteLockFunc(name, lsc) \
+static inline void di_write_lock_##name(struct dentry *d) \
+{ di_write_lock(d, AuLsc_DI_##lsc); }
+
+#define AuRWLockFuncs(name, lsc) \
+	AuReadLockFunc(name, lsc) \
+	AuWriteLockFunc(name, lsc)
+
+AuRWLockFuncs(child, CHILD);
+AuRWLockFuncs(child2, CHILD2);
+AuRWLockFuncs(child3, CHILD3);
+AuRWLockFuncs(parent, PARENT);
+AuRWLockFuncs(parent2, PARENT2);
+AuRWLockFuncs(parent3, PARENT3);
+
+#undef AuReadLockFunc
+#undef AuWriteLockFunc
+#undef AuRWLockFuncs
+
+#define DiMustNoWaiters(d)	AuRwMustNoWaiters(&au_di(d)->di_rwsem)
+#define DiMustAnyLock(d)	AuRwMustAnyLock(&au_di(d)->di_rwsem)
+#define DiMustWriteLock(d)	AuRwMustWriteLock(&au_di(d)->di_rwsem)
+
+/* ---------------------------------------------------------------------- */
+
+/* todo: memory barrier? */
+static inline unsigned int au_digen(struct dentry *d)
+{
+	return atomic_read(&au_di(d)->di_generation);
+}
+
+static inline void au_h_dentry_init(struct au_hdentry *hdentry)
+{
+	hdentry->hd_dentry = NULL;
+}
+
+static inline struct au_hdentry *au_hdentry(struct au_dinfo *di,
+					    aufs_bindex_t bindex)
+{
+	return di->di_hdentry + bindex;
+}
+
+static inline void au_hdput(struct au_hdentry *hd)
+{
+	if (hd)
+		dput(hd->hd_dentry);
+}
+
+static inline aufs_bindex_t au_dbtop(struct dentry *dentry)
+{
+	DiMustAnyLock(dentry);
+	return au_di(dentry)->di_btop;
+}
+
+static inline aufs_bindex_t au_dbbot(struct dentry *dentry)
+{
+	DiMustAnyLock(dentry);
+	return au_di(dentry)->di_bbot;
+}
+
+static inline aufs_bindex_t au_dbwh(struct dentry *dentry)
+{
+	DiMustAnyLock(dentry);
+	return au_di(dentry)->di_bwh;
+}
+
+static inline aufs_bindex_t au_dbdiropq(struct dentry *dentry)
+{
+	DiMustAnyLock(dentry);
+	return au_di(dentry)->di_bdiropq;
+}
+
+/* todo: hard/soft set? */
+static inline void au_set_dbtop(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	DiMustWriteLock(dentry);
+	au_di(dentry)->di_btop = bindex;
+}
+
+static inline void au_set_dbbot(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	DiMustWriteLock(dentry);
+	au_di(dentry)->di_bbot = bindex;
+}
+
+static inline void au_set_dbwh(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	DiMustWriteLock(dentry);
+	/* dbwh can be outside of btop - bbot range */
+	au_di(dentry)->di_bwh = bindex;
+}
+
+static inline void au_set_dbdiropq(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	DiMustWriteLock(dentry);
+	au_di(dentry)->di_bdiropq = bindex;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_HNOTIFY
+static inline void au_digen_dec(struct dentry *d)
+{
+	atomic_dec(&au_di(d)->di_generation);
+}
+
+static inline void au_hn_di_reinit(struct dentry *dentry)
+{
+	dentry->d_fsdata = NULL;
+}
+#else
+AuStubVoid(au_hn_di_reinit, struct dentry *dentry __maybe_unused)
+#endif /* CONFIG_AUFS_HNOTIFY */
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_DENTRY_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dinfo.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dinfo.c
@@ -0,0 +1,554 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * dentry private data
+ */
+
+#include "aufs.h"
+
+void au_di_init_once(void *_dinfo)
+{
+	struct au_dinfo *dinfo = _dinfo;
+
+	au_rw_init(&dinfo->di_rwsem);
+}
+
+struct au_dinfo *au_di_alloc(struct super_block *sb, unsigned int lsc)
+{
+	struct au_dinfo *dinfo;
+	int nbr, i;
+
+	dinfo = au_cache_alloc_dinfo();
+	if (unlikely(!dinfo))
+		goto out;
+
+	nbr = au_sbbot(sb) + 1;
+	if (nbr <= 0)
+		nbr = 1;
+	dinfo->di_hdentry = kcalloc(nbr, sizeof(*dinfo->di_hdentry), GFP_NOFS);
+	if (dinfo->di_hdentry) {
+		au_rw_write_lock_nested(&dinfo->di_rwsem, lsc);
+		dinfo->di_btop = -1;
+		dinfo->di_bbot = -1;
+		dinfo->di_bwh = -1;
+		dinfo->di_bdiropq = -1;
+		dinfo->di_tmpfile = 0;
+		for (i = 0; i < nbr; i++)
+			dinfo->di_hdentry[i].hd_id = -1;
+		goto out;
+	}
+
+	au_cache_free_dinfo(dinfo);
+	dinfo = NULL;
+
+out:
+	return dinfo;
+}
+
+void au_di_free(struct au_dinfo *dinfo)
+{
+	struct au_hdentry *p;
+	aufs_bindex_t bbot, bindex;
+
+	/* dentry may not be revalidated */
+	bindex = dinfo->di_btop;
+	if (bindex >= 0) {
+		bbot = dinfo->di_bbot;
+		p = au_hdentry(dinfo, bindex);
+		while (bindex++ <= bbot)
+			au_hdput(p++);
+	}
+	au_kfree_try_rcu(dinfo->di_hdentry);
+	au_cache_free_dinfo(dinfo);
+}
+
+void au_di_swap(struct au_dinfo *a, struct au_dinfo *b)
+{
+	struct au_hdentry *p;
+	aufs_bindex_t bi;
+
+	AuRwMustWriteLock(&a->di_rwsem);
+	AuRwMustWriteLock(&b->di_rwsem);
+
+#define DiSwap(v, name)				\
+	do {					\
+		v = a->di_##name;		\
+		a->di_##name = b->di_##name;	\
+		b->di_##name = v;		\
+	} while (0)
+
+	DiSwap(p, hdentry);
+	DiSwap(bi, btop);
+	DiSwap(bi, bbot);
+	DiSwap(bi, bwh);
+	DiSwap(bi, bdiropq);
+	/* smp_mb(); */
+
+#undef DiSwap
+}
+
+void au_di_cp(struct au_dinfo *dst, struct au_dinfo *src)
+{
+	AuRwMustWriteLock(&dst->di_rwsem);
+	AuRwMustWriteLock(&src->di_rwsem);
+
+	dst->di_btop = src->di_btop;
+	dst->di_bbot = src->di_bbot;
+	dst->di_bwh = src->di_bwh;
+	dst->di_bdiropq = src->di_bdiropq;
+	/* smp_mb(); */
+}
+
+int au_di_init(struct dentry *dentry)
+{
+	int err;
+	struct super_block *sb;
+	struct au_dinfo *dinfo;
+
+	err = 0;
+	sb = dentry->d_sb;
+	dinfo = au_di_alloc(sb, AuLsc_DI_CHILD);
+	if (dinfo) {
+		atomic_set(&dinfo->di_generation, au_sigen(sb));
+		/* smp_mb(); */ /* atomic_set */
+		dentry->d_fsdata = dinfo;
+	} else
+		err = -ENOMEM;
+
+	return err;
+}
+
+void au_di_fin(struct dentry *dentry)
+{
+	struct au_dinfo *dinfo;
+
+	dinfo = au_di(dentry);
+	AuRwDestroy(&dinfo->di_rwsem);
+	au_di_free(dinfo);
+}
+
+int au_di_realloc(struct au_dinfo *dinfo, int nbr, int may_shrink)
+{
+	int err, sz;
+	struct au_hdentry *hdp;
+
+	AuRwMustWriteLock(&dinfo->di_rwsem);
+
+	err = -ENOMEM;
+	sz = sizeof(*hdp) * (dinfo->di_bbot + 1);
+	if (!sz)
+		sz = sizeof(*hdp);
+	hdp = au_kzrealloc(dinfo->di_hdentry, sz, sizeof(*hdp) * nbr, GFP_NOFS,
+			   may_shrink);
+	if (hdp) {
+		dinfo->di_hdentry = hdp;
+		err = 0;
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void do_ii_write_lock(struct inode *inode, unsigned int lsc)
+{
+	switch (lsc) {
+	case AuLsc_DI_CHILD:
+		ii_write_lock_child(inode);
+		break;
+	case AuLsc_DI_CHILD2:
+		ii_write_lock_child2(inode);
+		break;
+	case AuLsc_DI_CHILD3:
+		ii_write_lock_child3(inode);
+		break;
+	case AuLsc_DI_PARENT:
+		ii_write_lock_parent(inode);
+		break;
+	case AuLsc_DI_PARENT2:
+		ii_write_lock_parent2(inode);
+		break;
+	case AuLsc_DI_PARENT3:
+		ii_write_lock_parent3(inode);
+		break;
+	default:
+		BUG();
+	}
+}
+
+static void do_ii_read_lock(struct inode *inode, unsigned int lsc)
+{
+	switch (lsc) {
+	case AuLsc_DI_CHILD:
+		ii_read_lock_child(inode);
+		break;
+	case AuLsc_DI_CHILD2:
+		ii_read_lock_child2(inode);
+		break;
+	case AuLsc_DI_CHILD3:
+		ii_read_lock_child3(inode);
+		break;
+	case AuLsc_DI_PARENT:
+		ii_read_lock_parent(inode);
+		break;
+	case AuLsc_DI_PARENT2:
+		ii_read_lock_parent2(inode);
+		break;
+	case AuLsc_DI_PARENT3:
+		ii_read_lock_parent3(inode);
+		break;
+	default:
+		BUG();
+	}
+}
+
+void di_read_lock(struct dentry *d, int flags, unsigned int lsc)
+{
+	struct inode *inode;
+
+	au_rw_read_lock_nested(&au_di(d)->di_rwsem, lsc);
+	if (d_really_is_positive(d)) {
+		inode = d_inode(d);
+		if (au_ftest_lock(flags, IW))
+			do_ii_write_lock(inode, lsc);
+		else if (au_ftest_lock(flags, IR))
+			do_ii_read_lock(inode, lsc);
+	}
+}
+
+void di_read_unlock(struct dentry *d, int flags)
+{
+	struct inode *inode;
+
+	if (d_really_is_positive(d)) {
+		inode = d_inode(d);
+		if (au_ftest_lock(flags, IW)) {
+			au_dbg_verify_dinode(d);
+			ii_write_unlock(inode);
+		} else if (au_ftest_lock(flags, IR)) {
+			au_dbg_verify_dinode(d);
+			ii_read_unlock(inode);
+		}
+	}
+	au_rw_read_unlock(&au_di(d)->di_rwsem);
+}
+
+void di_downgrade_lock(struct dentry *d, int flags)
+{
+	if (d_really_is_positive(d) && au_ftest_lock(flags, IR))
+		ii_downgrade_lock(d_inode(d));
+	au_rw_dgrade_lock(&au_di(d)->di_rwsem);
+}
+
+void di_write_lock(struct dentry *d, unsigned int lsc)
+{
+	au_rw_write_lock_nested(&au_di(d)->di_rwsem, lsc);
+	if (d_really_is_positive(d))
+		do_ii_write_lock(d_inode(d), lsc);
+}
+
+void di_write_unlock(struct dentry *d)
+{
+	au_dbg_verify_dinode(d);
+	if (d_really_is_positive(d))
+		ii_write_unlock(d_inode(d));
+	au_rw_write_unlock(&au_di(d)->di_rwsem);
+}
+
+void di_write_lock2_child(struct dentry *d1, struct dentry *d2, int isdir)
+{
+	AuDebugOn(d1 == d2
+		  || d_inode(d1) == d_inode(d2)
+		  || d1->d_sb != d2->d_sb);
+
+	if ((isdir && au_test_subdir(d1, d2))
+	    || d1 < d2) {
+		di_write_lock_child(d1);
+		di_write_lock_child2(d2);
+	} else {
+		di_write_lock_child(d2);
+		di_write_lock_child2(d1);
+	}
+}
+
+void di_write_lock2_parent(struct dentry *d1, struct dentry *d2, int isdir)
+{
+	AuDebugOn(d1 == d2
+		  || d_inode(d1) == d_inode(d2)
+		  || d1->d_sb != d2->d_sb);
+
+	if ((isdir && au_test_subdir(d1, d2))
+	    || d1 < d2) {
+		di_write_lock_parent(d1);
+		di_write_lock_parent2(d2);
+	} else {
+		di_write_lock_parent(d2);
+		di_write_lock_parent2(d1);
+	}
+}
+
+void di_write_unlock2(struct dentry *d1, struct dentry *d2)
+{
+	di_write_unlock(d1);
+	if (d_inode(d1) == d_inode(d2))
+		au_rw_write_unlock(&au_di(d2)->di_rwsem);
+	else
+		di_write_unlock(d2);
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct dentry *au_h_dptr(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	struct dentry *d;
+
+	DiMustAnyLock(dentry);
+
+	if (au_dbtop(dentry) < 0 || bindex < au_dbtop(dentry))
+		return NULL;
+	AuDebugOn(bindex < 0);
+	d = au_hdentry(au_di(dentry), bindex)->hd_dentry;
+	AuDebugOn(d && au_dcount(d) <= 0);
+	return d;
+}
+
+/*
+ * extended version of au_h_dptr().
+ * returns a hashed and positive (or linkable) h_dentry in bindex, NULL, or
+ * error.
+ */
+struct dentry *au_h_d_alias(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	struct dentry *h_dentry;
+	struct inode *inode, *h_inode;
+
+	AuDebugOn(d_really_is_negative(dentry));
+
+	h_dentry = NULL;
+	if (au_dbtop(dentry) <= bindex
+	    && bindex <= au_dbbot(dentry))
+		h_dentry = au_h_dptr(dentry, bindex);
+	if (h_dentry && !au_d_linkable(h_dentry)) {
+		dget(h_dentry);
+		goto out; /* success */
+	}
+
+	inode = d_inode(dentry);
+	AuDebugOn(bindex < au_ibtop(inode));
+	AuDebugOn(au_ibbot(inode) < bindex);
+	h_inode = au_h_iptr(inode, bindex);
+	h_dentry = d_find_alias(h_inode);
+	if (h_dentry) {
+		if (!IS_ERR(h_dentry)) {
+			if (!au_d_linkable(h_dentry))
+				goto out; /* success */
+			dput(h_dentry);
+		} else
+			goto out;
+	}
+
+	if (au_opt_test(au_mntflags(dentry->d_sb), PLINK)) {
+		h_dentry = au_plink_lkup(inode, bindex);
+		AuDebugOn(!h_dentry);
+		if (!IS_ERR(h_dentry)) {
+			if (!au_d_hashed_positive(h_dentry))
+				goto out; /* success */
+			dput(h_dentry);
+			h_dentry = NULL;
+		}
+	}
+
+out:
+	AuDbgDentry(h_dentry);
+	return h_dentry;
+}
+
+aufs_bindex_t au_dbtail(struct dentry *dentry)
+{
+	aufs_bindex_t bbot, bwh;
+
+	bbot = au_dbbot(dentry);
+	if (0 <= bbot) {
+		bwh = au_dbwh(dentry);
+		if (!bwh)
+			return bwh;
+		if (0 < bwh && bwh < bbot)
+			return bwh - 1;
+	}
+	return bbot;
+}
+
+aufs_bindex_t au_dbtaildir(struct dentry *dentry)
+{
+	aufs_bindex_t bbot, bopq;
+
+	bbot = au_dbtail(dentry);
+	if (0 <= bbot) {
+		bopq = au_dbdiropq(dentry);
+		if (0 <= bopq && bopq < bbot)
+			bbot = bopq;
+	}
+	return bbot;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_set_h_dptr(struct dentry *dentry, aufs_bindex_t bindex,
+		   struct dentry *h_dentry)
+{
+	struct au_dinfo *dinfo;
+	struct au_hdentry *hd;
+	struct au_branch *br;
+
+	DiMustWriteLock(dentry);
+
+	dinfo = au_di(dentry);
+	hd = au_hdentry(dinfo, bindex);
+	au_hdput(hd);
+	hd->hd_dentry = h_dentry;
+	if (h_dentry) {
+		br = au_sbr(dentry->d_sb, bindex);
+		hd->hd_id = br->br_id;
+	}
+}
+
+int au_dbrange_test(struct dentry *dentry)
+{
+	int err;
+	aufs_bindex_t btop, bbot;
+
+	err = 0;
+	btop = au_dbtop(dentry);
+	bbot = au_dbbot(dentry);
+	if (btop >= 0)
+		AuDebugOn(bbot < 0 && btop > bbot);
+	else {
+		err = -EIO;
+		AuDebugOn(bbot >= 0);
+	}
+
+	return err;
+}
+
+int au_digen_test(struct dentry *dentry, unsigned int sigen)
+{
+	int err;
+
+	err = 0;
+	if (unlikely(au_digen(dentry) != sigen
+		     || au_iigen_test(d_inode(dentry), sigen)))
+		err = -EIO;
+
+	return err;
+}
+
+void au_update_digen(struct dentry *dentry)
+{
+	atomic_set(&au_di(dentry)->di_generation, au_sigen(dentry->d_sb));
+	/* smp_mb(); */ /* atomic_set */
+}
+
+void au_update_dbrange(struct dentry *dentry, int do_put_zero)
+{
+	struct au_dinfo *dinfo;
+	struct dentry *h_d;
+	struct au_hdentry *hdp;
+	aufs_bindex_t bindex, bbot;
+
+	DiMustWriteLock(dentry);
+
+	dinfo = au_di(dentry);
+	if (!dinfo || dinfo->di_btop < 0)
+		return;
+
+	if (do_put_zero) {
+		bbot = dinfo->di_bbot;
+		bindex = dinfo->di_btop;
+		hdp = au_hdentry(dinfo, bindex);
+		for (; bindex <= bbot; bindex++, hdp++) {
+			h_d = hdp->hd_dentry;
+			if (h_d && d_is_negative(h_d))
+				au_set_h_dptr(dentry, bindex, NULL);
+		}
+	}
+
+	dinfo->di_btop = 0;
+	hdp = au_hdentry(dinfo, dinfo->di_btop);
+	for (; dinfo->di_btop <= dinfo->di_bbot; dinfo->di_btop++, hdp++)
+		if (hdp->hd_dentry)
+			break;
+	if (dinfo->di_btop > dinfo->di_bbot) {
+		dinfo->di_btop = -1;
+		dinfo->di_bbot = -1;
+		return;
+	}
+
+	hdp = au_hdentry(dinfo, dinfo->di_bbot);
+	for (; dinfo->di_bbot >= 0; dinfo->di_bbot--, hdp--)
+		if (hdp->hd_dentry)
+			break;
+	AuDebugOn(dinfo->di_btop > dinfo->di_bbot || dinfo->di_bbot < 0);
+}
+
+void au_update_dbtop(struct dentry *dentry)
+{
+	aufs_bindex_t bindex, bbot;
+	struct dentry *h_dentry;
+
+	bbot = au_dbbot(dentry);
+	for (bindex = au_dbtop(dentry); bindex <= bbot; bindex++) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (!h_dentry)
+			continue;
+		if (d_is_positive(h_dentry)) {
+			au_set_dbtop(dentry, bindex);
+			return;
+		}
+		au_set_h_dptr(dentry, bindex, NULL);
+	}
+}
+
+void au_update_dbbot(struct dentry *dentry)
+{
+	aufs_bindex_t bindex, btop;
+	struct dentry *h_dentry;
+
+	btop = au_dbtop(dentry);
+	for (bindex = au_dbbot(dentry); bindex >= btop; bindex--) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (!h_dentry)
+			continue;
+		if (d_is_positive(h_dentry)) {
+			au_set_dbbot(dentry, bindex);
+			return;
+		}
+		au_set_h_dptr(dentry, bindex, NULL);
+	}
+}
+
+int au_find_dbindex(struct dentry *dentry, struct dentry *h_dentry)
+{
+	aufs_bindex_t bindex, bbot;
+
+	bbot = au_dbbot(dentry);
+	for (bindex = au_dbtop(dentry); bindex <= bbot; bindex++)
+		if (au_h_dptr(dentry, bindex) == h_dentry)
+			return bindex;
+	return -1;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dir.c
@@ -0,0 +1,765 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * directory operations
+ */
+
+#include <linux/fs_stack.h>
+#include <linux/iversion.h>
+#include "aufs.h"
+
+void au_add_nlink(struct inode *dir, struct inode *h_dir)
+{
+	unsigned int nlink;
+
+	AuDebugOn(!S_ISDIR(dir->i_mode) || !S_ISDIR(h_dir->i_mode));
+
+	nlink = dir->i_nlink;
+	nlink += h_dir->i_nlink - 2;
+	if (h_dir->i_nlink < 2)
+		nlink += 2;
+	smp_mb(); /* for i_nlink */
+	/* 0 can happen in revaliding */
+	set_nlink(dir, nlink);
+}
+
+void au_sub_nlink(struct inode *dir, struct inode *h_dir)
+{
+	unsigned int nlink;
+
+	AuDebugOn(!S_ISDIR(dir->i_mode) || !S_ISDIR(h_dir->i_mode));
+
+	nlink = dir->i_nlink;
+	nlink -= h_dir->i_nlink - 2;
+	if (h_dir->i_nlink < 2)
+		nlink -= 2;
+	smp_mb(); /* for i_nlink */
+	/* nlink == 0 means the branch-fs is broken */
+	set_nlink(dir, nlink);
+}
+
+loff_t au_dir_size(struct file *file, struct dentry *dentry)
+{
+	loff_t sz;
+	aufs_bindex_t bindex, bbot;
+	struct file *h_file;
+	struct dentry *h_dentry;
+
+	sz = 0;
+	if (file) {
+		AuDebugOn(!d_is_dir(file->f_path.dentry));
+
+		bbot = au_fbbot_dir(file);
+		for (bindex = au_fbtop(file);
+		     bindex <= bbot && sz < KMALLOC_MAX_SIZE;
+		     bindex++) {
+			h_file = au_hf_dir(file, bindex);
+			if (h_file && file_inode(h_file))
+				sz += vfsub_f_size_read(h_file);
+		}
+	} else {
+		AuDebugOn(!dentry);
+		AuDebugOn(!d_is_dir(dentry));
+
+		bbot = au_dbtaildir(dentry);
+		for (bindex = au_dbtop(dentry);
+		     bindex <= bbot && sz < KMALLOC_MAX_SIZE;
+		     bindex++) {
+			h_dentry = au_h_dptr(dentry, bindex);
+			if (h_dentry && d_is_positive(h_dentry))
+				sz += i_size_read(d_inode(h_dentry));
+		}
+	}
+	if (sz < KMALLOC_MAX_SIZE)
+		sz = roundup_pow_of_two(sz);
+	if (sz > KMALLOC_MAX_SIZE)
+		sz = KMALLOC_MAX_SIZE;
+	else if (sz < NAME_MAX) {
+		BUILD_BUG_ON(AUFS_RDBLK_DEF < NAME_MAX);
+		sz = AUFS_RDBLK_DEF;
+	}
+	return sz;
+}
+
+struct au_dir_ts_arg {
+	struct dentry *dentry;
+	aufs_bindex_t brid;
+};
+
+static void au_do_dir_ts(void *arg)
+{
+	struct au_dir_ts_arg *a = arg;
+	struct au_dtime dt;
+	struct path h_path;
+	struct inode *dir, *h_dir;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_hinode *hdir;
+	int err;
+	aufs_bindex_t btop, bindex;
+
+	sb = a->dentry->d_sb;
+	if (d_really_is_negative(a->dentry))
+		goto out;
+	/* no dir->i_mutex lock */
+	aufs_read_lock(a->dentry, AuLock_DW); /* noflush */
+
+	dir = d_inode(a->dentry);
+	btop = au_ibtop(dir);
+	bindex = au_br_index(sb, a->brid);
+	if (bindex < btop)
+		goto out_unlock;
+
+	br = au_sbr(sb, bindex);
+	h_path.dentry = au_h_dptr(a->dentry, bindex);
+	if (!h_path.dentry)
+		goto out_unlock;
+	h_path.mnt = au_br_mnt(br);
+	au_dtime_store(&dt, a->dentry, &h_path);
+
+	br = au_sbr(sb, btop);
+	if (!au_br_writable(br->br_perm))
+		goto out_unlock;
+	h_path.dentry = au_h_dptr(a->dentry, btop);
+	h_path.mnt = au_br_mnt(br);
+	err = vfsub_mnt_want_write(h_path.mnt);
+	if (err)
+		goto out_unlock;
+	hdir = au_hi(dir, btop);
+	au_hn_inode_lock_nested(hdir, AuLsc_I_PARENT);
+	h_dir = au_h_iptr(dir, btop);
+	if (h_dir->i_nlink
+	    && timespec64_compare(&h_dir->i_mtime, &dt.dt_mtime) < 0) {
+		dt.dt_h_path = h_path;
+		au_dtime_revert(&dt);
+	}
+	au_hn_inode_unlock(hdir);
+	vfsub_mnt_drop_write(h_path.mnt);
+	au_cpup_attr_timesizes(dir);
+
+out_unlock:
+	aufs_read_unlock(a->dentry, AuLock_DW);
+out:
+	dput(a->dentry);
+	au_nwt_done(&au_sbi(sb)->si_nowait);
+	au_kfree_try_rcu(arg);
+}
+
+void au_dir_ts(struct inode *dir, aufs_bindex_t bindex)
+{
+	int perm, wkq_err;
+	aufs_bindex_t btop;
+	struct au_dir_ts_arg *arg;
+	struct dentry *dentry;
+	struct super_block *sb;
+
+	IMustLock(dir);
+
+	dentry = d_find_any_alias(dir);
+	AuDebugOn(!dentry);
+	sb = dentry->d_sb;
+	btop = au_ibtop(dir);
+	if (btop == bindex) {
+		au_cpup_attr_timesizes(dir);
+		goto out;
+	}
+
+	perm = au_sbr_perm(sb, btop);
+	if (!au_br_writable(perm))
+		goto out;
+
+	arg = kmalloc(sizeof(*arg), GFP_NOFS);
+	if (!arg)
+		goto out;
+
+	arg->dentry = dget(dentry); /* will be dput-ted by au_do_dir_ts() */
+	arg->brid = au_sbr_id(sb, bindex);
+	wkq_err = au_wkq_nowait(au_do_dir_ts, arg, sb, /*flags*/0);
+	if (unlikely(wkq_err)) {
+		pr_err("wkq %d\n", wkq_err);
+		dput(dentry);
+		au_kfree_try_rcu(arg);
+	}
+
+out:
+	dput(dentry);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int reopen_dir(struct file *file)
+{
+	int err;
+	unsigned int flags;
+	aufs_bindex_t bindex, btail, btop;
+	struct dentry *dentry, *h_dentry;
+	struct file *h_file;
+
+	/* open all lower dirs */
+	dentry = file->f_path.dentry;
+	btop = au_dbtop(dentry);
+	for (bindex = au_fbtop(file); bindex < btop; bindex++)
+		au_set_h_fptr(file, bindex, NULL);
+	au_set_fbtop(file, btop);
+
+	btail = au_dbtaildir(dentry);
+	for (bindex = au_fbbot_dir(file); btail < bindex; bindex--)
+		au_set_h_fptr(file, bindex, NULL);
+	au_set_fbbot_dir(file, btail);
+
+	flags = vfsub_file_flags(file);
+	for (bindex = btop; bindex <= btail; bindex++) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (!h_dentry)
+			continue;
+		h_file = au_hf_dir(file, bindex);
+		if (h_file)
+			continue;
+
+		h_file = au_h_open(dentry, bindex, flags, file, /*force_wr*/0);
+		err = PTR_ERR(h_file);
+		if (IS_ERR(h_file))
+			goto out; /* close all? */
+		au_set_h_fptr(file, bindex, h_file);
+	}
+	au_update_figen(file);
+	/* todo: necessary? */
+	/* file->f_ra = h_file->f_ra; */
+	err = 0;
+
+out:
+	return err;
+}
+
+static int do_open_dir(struct file *file, int flags, struct file *h_file)
+{
+	int err;
+	aufs_bindex_t bindex, btail;
+	struct dentry *dentry, *h_dentry;
+	struct vfsmount *mnt;
+
+	FiMustWriteLock(file);
+	AuDebugOn(h_file);
+
+	err = 0;
+	mnt = file->f_path.mnt;
+	dentry = file->f_path.dentry;
+	file->f_version = inode_query_iversion(d_inode(dentry));
+	bindex = au_dbtop(dentry);
+	au_set_fbtop(file, bindex);
+	btail = au_dbtaildir(dentry);
+	au_set_fbbot_dir(file, btail);
+	for (; !err && bindex <= btail; bindex++) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (!h_dentry)
+			continue;
+
+		err = vfsub_test_mntns(mnt, h_dentry->d_sb);
+		if (unlikely(err))
+			break;
+		h_file = au_h_open(dentry, bindex, flags, file, /*force_wr*/0);
+		if (IS_ERR(h_file)) {
+			err = PTR_ERR(h_file);
+			break;
+		}
+		au_set_h_fptr(file, bindex, h_file);
+	}
+	au_update_figen(file);
+	/* todo: necessary? */
+	/* file->f_ra = h_file->f_ra; */
+	if (!err)
+		return 0; /* success */
+
+	/* close all */
+	for (bindex = au_fbtop(file); bindex <= btail; bindex++)
+		au_set_h_fptr(file, bindex, NULL);
+	au_set_fbtop(file, -1);
+	au_set_fbbot_dir(file, -1);
+
+	return err;
+}
+
+static int aufs_open_dir(struct inode *inode __maybe_unused,
+			 struct file *file)
+{
+	int err;
+	struct super_block *sb;
+	struct au_fidir *fidir;
+
+	err = -ENOMEM;
+	sb = file->f_path.dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH);
+	fidir = au_fidir_alloc(sb);
+	if (fidir) {
+		struct au_do_open_args args = {
+			.open	= do_open_dir,
+			.fidir	= fidir
+		};
+		err = au_do_open(file, &args);
+		if (unlikely(err))
+			au_kfree_rcu(fidir);
+	}
+	si_read_unlock(sb);
+	return err;
+}
+
+static int aufs_release_dir(struct inode *inode __maybe_unused,
+			    struct file *file)
+{
+	struct au_vdir *vdir_cache;
+	struct au_finfo *finfo;
+	struct au_fidir *fidir;
+	struct au_hfile *hf;
+	aufs_bindex_t bindex, bbot;
+
+	finfo = au_fi(file);
+	fidir = finfo->fi_hdir;
+	if (fidir) {
+		au_hbl_del(&finfo->fi_hlist,
+			   &au_sbi(file->f_path.dentry->d_sb)->si_files);
+		vdir_cache = fidir->fd_vdir_cache; /* lock-free */
+		if (vdir_cache)
+			au_vdir_free(vdir_cache);
+
+		bindex = finfo->fi_btop;
+		if (bindex >= 0) {
+			hf = fidir->fd_hfile + bindex;
+			/*
+			 * calls fput() instead of filp_close(),
+			 * since no dnotify or lock for the lower file.
+			 */
+			bbot = fidir->fd_bbot;
+			for (; bindex <= bbot; bindex++, hf++)
+				if (hf->hf_file)
+					au_hfput(hf, /*execed*/0);
+		}
+		au_kfree_rcu(fidir);
+		finfo->fi_hdir = NULL;
+	}
+	au_finfo_fin(file);
+	return 0;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_do_flush_dir(struct file *file, fl_owner_t id)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct file *h_file;
+
+	err = 0;
+	bbot = au_fbbot_dir(file);
+	for (bindex = au_fbtop(file); !err && bindex <= bbot; bindex++) {
+		h_file = au_hf_dir(file, bindex);
+		if (h_file)
+			err = vfsub_flush(h_file, id);
+	}
+	return err;
+}
+
+static int aufs_flush_dir(struct file *file, fl_owner_t id)
+{
+	return au_do_flush(file, id, au_do_flush_dir);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_do_fsync_dir_no_file(struct dentry *dentry, int datasync)
+{
+	int err;
+	aufs_bindex_t bbot, bindex;
+	struct inode *inode;
+	struct super_block *sb;
+
+	err = 0;
+	sb = dentry->d_sb;
+	inode = d_inode(dentry);
+	IMustLock(inode);
+	bbot = au_dbbot(dentry);
+	for (bindex = au_dbtop(dentry); !err && bindex <= bbot; bindex++) {
+		struct path h_path;
+
+		if (au_test_ro(sb, bindex, inode))
+			continue;
+		h_path.dentry = au_h_dptr(dentry, bindex);
+		if (!h_path.dentry)
+			continue;
+
+		h_path.mnt = au_sbr_mnt(sb, bindex);
+		err = vfsub_fsync(NULL, &h_path, datasync);
+	}
+
+	return err;
+}
+
+static int au_do_fsync_dir(struct file *file, int datasync)
+{
+	int err;
+	aufs_bindex_t bbot, bindex;
+	struct file *h_file;
+	struct super_block *sb;
+	struct inode *inode;
+
+	err = au_reval_and_lock_fdi(file, reopen_dir, /*wlock*/1, /*fi_lsc*/0);
+	if (unlikely(err))
+		goto out;
+
+	inode = file_inode(file);
+	sb = inode->i_sb;
+	bbot = au_fbbot_dir(file);
+	for (bindex = au_fbtop(file); !err && bindex <= bbot; bindex++) {
+		h_file = au_hf_dir(file, bindex);
+		if (!h_file || au_test_ro(sb, bindex, inode))
+			continue;
+
+		err = vfsub_fsync(h_file, &h_file->f_path, datasync);
+	}
+
+out:
+	return err;
+}
+
+/*
+ * @file may be NULL
+ */
+static int aufs_fsync_dir(struct file *file, loff_t start, loff_t end,
+			  int datasync)
+{
+	int err;
+	struct dentry *dentry;
+	struct inode *inode;
+	struct super_block *sb;
+
+	err = 0;
+	dentry = file->f_path.dentry;
+	inode = d_inode(dentry);
+	inode_lock(inode);
+	sb = dentry->d_sb;
+	si_noflush_read_lock(sb);
+	if (file)
+		err = au_do_fsync_dir(file, datasync);
+	else {
+		di_write_lock_child(dentry);
+		err = au_do_fsync_dir_no_file(dentry, datasync);
+	}
+	au_cpup_attr_timesizes(inode);
+	di_write_unlock(dentry);
+	if (file)
+		fi_write_unlock(file);
+
+	si_read_unlock(sb);
+	inode_unlock(inode);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int aufs_iterate_shared(struct file *file, struct dir_context *ctx)
+{
+	int err;
+	struct dentry *dentry;
+	struct inode *inode, *h_inode;
+	struct super_block *sb;
+
+	AuDbg("%pD, ctx{%ps, %llu}\n", file, ctx->actor, ctx->pos);
+
+	dentry = file->f_path.dentry;
+	inode = d_inode(dentry);
+	IMustLock(inode);
+
+	sb = dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH);
+	err = au_reval_and_lock_fdi(file, reopen_dir, /*wlock*/1, /*fi_lsc*/0);
+	if (unlikely(err))
+		goto out;
+	err = au_alive_dir(dentry);
+	if (!err)
+		err = au_vdir_init(file);
+	di_downgrade_lock(dentry, AuLock_IR);
+	if (unlikely(err))
+		goto out_unlock;
+
+	h_inode = au_h_iptr(inode, au_ibtop(inode));
+	if (!au_test_nfsd()) {
+		err = au_vdir_fill_de(file, ctx);
+		fsstack_copy_attr_atime(inode, h_inode);
+	} else {
+		/*
+		 * nfsd filldir may call lookup_one_len(), vfs_getattr(),
+		 * encode_fh() and others.
+		 */
+		atomic_inc(&h_inode->i_count);
+		di_read_unlock(dentry, AuLock_IR);
+		si_read_unlock(sb);
+		err = au_vdir_fill_de(file, ctx);
+		fsstack_copy_attr_atime(inode, h_inode);
+		fi_write_unlock(file);
+		iput(h_inode);
+
+		AuTraceErr(err);
+		return err;
+	}
+
+out_unlock:
+	di_read_unlock(dentry, AuLock_IR);
+	fi_write_unlock(file);
+out:
+	si_read_unlock(sb);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#define AuTestEmpty_WHONLY	1
+#define AuTestEmpty_CALLED	(1 << 1)
+#define AuTestEmpty_SHWH	(1 << 2)
+#define au_ftest_testempty(flags, name)	((flags) & AuTestEmpty_##name)
+#define au_fset_testempty(flags, name) \
+	do { (flags) |= AuTestEmpty_##name; } while (0)
+#define au_fclr_testempty(flags, name) \
+	do { (flags) &= ~AuTestEmpty_##name; } while (0)
+
+#ifndef CONFIG_AUFS_SHWH
+#undef AuTestEmpty_SHWH
+#define AuTestEmpty_SHWH	0
+#endif
+
+struct test_empty_arg {
+	struct dir_context ctx;
+	struct au_nhash *whlist;
+	unsigned int flags;
+	int err;
+	aufs_bindex_t bindex;
+};
+
+static int test_empty_cb(struct dir_context *ctx, const char *__name,
+			 int namelen, loff_t offset __maybe_unused, u64 ino,
+			 unsigned int d_type)
+{
+	struct test_empty_arg *arg = container_of(ctx, struct test_empty_arg,
+						  ctx);
+	char *name = (void *)__name;
+
+	arg->err = 0;
+	au_fset_testempty(arg->flags, CALLED);
+	/* smp_mb(); */
+	if (name[0] == '.'
+	    && (namelen == 1 || (name[1] == '.' && namelen == 2)))
+		goto out; /* success */
+
+	if (namelen <= AUFS_WH_PFX_LEN
+	    || memcmp(name, AUFS_WH_PFX, AUFS_WH_PFX_LEN)) {
+		if (au_ftest_testempty(arg->flags, WHONLY)
+		    && !au_nhash_test_known_wh(arg->whlist, name, namelen))
+			arg->err = -ENOTEMPTY;
+		goto out;
+	}
+
+	name += AUFS_WH_PFX_LEN;
+	namelen -= AUFS_WH_PFX_LEN;
+	if (!au_nhash_test_known_wh(arg->whlist, name, namelen))
+		arg->err = au_nhash_append_wh
+			(arg->whlist, name, namelen, ino, d_type, arg->bindex,
+			 au_ftest_testempty(arg->flags, SHWH));
+
+out:
+	/* smp_mb(); */
+	AuTraceErr(arg->err);
+	return arg->err;
+}
+
+static int do_test_empty(struct dentry *dentry, struct test_empty_arg *arg)
+{
+	int err;
+	struct file *h_file;
+	struct au_branch *br;
+
+	h_file = au_h_open(dentry, arg->bindex,
+			   O_RDONLY | O_NONBLOCK | O_DIRECTORY | O_LARGEFILE,
+			   /*file*/NULL, /*force_wr*/0);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	err = 0;
+	if (!au_opt_test(au_mntflags(dentry->d_sb), UDBA_NONE)
+	    && !file_inode(h_file)->i_nlink)
+		goto out_put;
+
+	do {
+		arg->err = 0;
+		au_fclr_testempty(arg->flags, CALLED);
+		/* smp_mb(); */
+		err = vfsub_iterate_dir(h_file, &arg->ctx);
+		if (err >= 0)
+			err = arg->err;
+	} while (!err && au_ftest_testempty(arg->flags, CALLED));
+
+out_put:
+	fput(h_file);
+	br = au_sbr(dentry->d_sb, arg->bindex);
+	au_lcnt_dec(&br->br_nfiles);
+out:
+	return err;
+}
+
+struct do_test_empty_args {
+	int *errp;
+	struct dentry *dentry;
+	struct test_empty_arg *arg;
+};
+
+static void call_do_test_empty(void *args)
+{
+	struct do_test_empty_args *a = args;
+	*a->errp = do_test_empty(a->dentry, a->arg);
+}
+
+static int sio_test_empty(struct dentry *dentry, struct test_empty_arg *arg)
+{
+	int err, wkq_err;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	struct user_namespace *h_userns;
+
+	h_userns = au_sbr_userns(dentry->d_sb, arg->bindex);
+	h_dentry = au_h_dptr(dentry, arg->bindex);
+	h_inode = d_inode(h_dentry);
+	/* todo: i_mode changes anytime? */
+	inode_lock_shared_nested(h_inode, AuLsc_I_CHILD);
+	err = au_test_h_perm_sio(h_userns, h_inode, MAY_EXEC | MAY_READ);
+	inode_unlock_shared(h_inode);
+	if (!err)
+		err = do_test_empty(dentry, arg);
+	else {
+		struct do_test_empty_args args = {
+			.errp	= &err,
+			.dentry	= dentry,
+			.arg	= arg
+		};
+		unsigned int flags = arg->flags;
+
+		wkq_err = au_wkq_wait(call_do_test_empty, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+		arg->flags = flags;
+	}
+
+	return err;
+}
+
+int au_test_empty_lower(struct dentry *dentry)
+{
+	int err;
+	unsigned int rdhash;
+	aufs_bindex_t bindex, btop, btail;
+	struct au_nhash whlist;
+	struct test_empty_arg arg = {
+		.ctx = {
+			.actor = test_empty_cb
+		}
+	};
+	int (*test_empty)(struct dentry *dentry, struct test_empty_arg *arg);
+
+	SiMustAnyLock(dentry->d_sb);
+
+	rdhash = au_sbi(dentry->d_sb)->si_rdhash;
+	if (!rdhash)
+		rdhash = au_rdhash_est(au_dir_size(/*file*/NULL, dentry));
+	err = au_nhash_alloc(&whlist, rdhash, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+
+	arg.flags = 0;
+	arg.whlist = &whlist;
+	btop = au_dbtop(dentry);
+	if (au_opt_test(au_mntflags(dentry->d_sb), SHWH))
+		au_fset_testempty(arg.flags, SHWH);
+	test_empty = do_test_empty;
+	if (au_opt_test(au_mntflags(dentry->d_sb), DIRPERM1))
+		test_empty = sio_test_empty;
+	arg.bindex = btop;
+	err = test_empty(dentry, &arg);
+	if (unlikely(err))
+		goto out_whlist;
+
+	au_fset_testempty(arg.flags, WHONLY);
+	btail = au_dbtaildir(dentry);
+	for (bindex = btop + 1; !err && bindex <= btail; bindex++) {
+		struct dentry *h_dentry;
+
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (h_dentry && d_is_positive(h_dentry)) {
+			arg.bindex = bindex;
+			err = test_empty(dentry, &arg);
+		}
+	}
+
+out_whlist:
+	au_nhash_wh_free(&whlist);
+out:
+	return err;
+}
+
+int au_test_empty(struct dentry *dentry, struct au_nhash *whlist)
+{
+	int err;
+	struct test_empty_arg arg = {
+		.ctx = {
+			.actor = test_empty_cb
+		}
+	};
+	aufs_bindex_t bindex, btail;
+
+	err = 0;
+	arg.whlist = whlist;
+	arg.flags = AuTestEmpty_WHONLY;
+	if (au_opt_test(au_mntflags(dentry->d_sb), SHWH))
+		au_fset_testempty(arg.flags, SHWH);
+	btail = au_dbtaildir(dentry);
+	for (bindex = au_dbtop(dentry); !err && bindex <= btail; bindex++) {
+		struct dentry *h_dentry;
+
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (h_dentry && d_is_positive(h_dentry)) {
+			arg.bindex = bindex;
+			err = sio_test_empty(dentry, &arg);
+		}
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+const struct file_operations aufs_dir_fop = {
+	.owner		= THIS_MODULE,
+	.llseek		= default_llseek,
+	.read		= generic_read_dir,
+	.iterate_shared	= aufs_iterate_shared,
+	.unlocked_ioctl	= aufs_ioctl_dir,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl	= aufs_compat_ioctl_dir,
+#endif
+	.open		= aufs_open_dir,
+	.release	= aufs_release_dir,
+	.flush		= aufs_flush_dir,
+	.fsync		= aufs_fsync_dir
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dir.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dir.h
@@ -0,0 +1,134 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * directory operations
+ */
+
+#ifndef __AUFS_DIR_H__
+#define __AUFS_DIR_H__
+
+#ifdef __KERNEL__
+
+#include <linux/fs.h>
+
+/* ---------------------------------------------------------------------- */
+
+/* need to be faster and smaller */
+
+struct au_nhash {
+	unsigned int		nh_num;
+	struct hlist_head	*nh_head;
+};
+
+struct au_vdir_destr {
+	unsigned char	len;
+	unsigned char	name[];
+} __packed;
+
+struct au_vdir_dehstr {
+	struct hlist_node	hash;
+	struct au_vdir_destr	*str;
+	struct rcu_head		rcu;
+} ____cacheline_aligned_in_smp;
+
+struct au_vdir_de {
+	ino_t			de_ino;
+	unsigned char		de_type;
+	/* caution: packed */
+	struct au_vdir_destr	de_str;
+} __packed;
+
+struct au_vdir_wh {
+	struct hlist_node	wh_hash;
+#ifdef CONFIG_AUFS_SHWH
+	ino_t			wh_ino;
+	aufs_bindex_t		wh_bindex;
+	unsigned char		wh_type;
+#else
+	aufs_bindex_t		wh_bindex;
+#endif
+	/* caution: packed */
+	struct au_vdir_destr	wh_str;
+} __packed;
+
+union au_vdir_deblk_p {
+	unsigned char		*deblk;
+	struct au_vdir_de	*de;
+};
+
+struct au_vdir {
+	unsigned char	**vd_deblk;
+	unsigned long	vd_nblk;
+	struct {
+		unsigned long		ul;
+		union au_vdir_deblk_p	p;
+	} vd_last;
+
+	u64		vd_version;
+	unsigned int	vd_deblk_sz;
+	unsigned long	vd_jiffy;
+	struct rcu_head	rcu;
+} ____cacheline_aligned_in_smp;
+
+/* ---------------------------------------------------------------------- */
+
+/* dir.c */
+extern const struct file_operations aufs_dir_fop;
+void au_add_nlink(struct inode *dir, struct inode *h_dir);
+void au_sub_nlink(struct inode *dir, struct inode *h_dir);
+loff_t au_dir_size(struct file *file, struct dentry *dentry);
+void au_dir_ts(struct inode *dir, aufs_bindex_t bsrc);
+int au_test_empty_lower(struct dentry *dentry);
+int au_test_empty(struct dentry *dentry, struct au_nhash *whlist);
+
+/* vdir.c */
+unsigned int au_rdhash_est(loff_t sz);
+int au_nhash_alloc(struct au_nhash *nhash, unsigned int num_hash, gfp_t gfp);
+void au_nhash_wh_free(struct au_nhash *whlist);
+int au_nhash_test_longer_wh(struct au_nhash *whlist, aufs_bindex_t btgt,
+			    int limit);
+int au_nhash_test_known_wh(struct au_nhash *whlist, char *name, int nlen);
+int au_nhash_append_wh(struct au_nhash *whlist, char *name, int nlen, ino_t ino,
+		       unsigned int d_type, aufs_bindex_t bindex,
+		       unsigned char shwh);
+void au_vdir_free(struct au_vdir *vdir);
+int au_vdir_init(struct file *file);
+int au_vdir_fill_de(struct file *file, struct dir_context *ctx);
+
+/* ioctl.c */
+long aufs_ioctl_dir(struct file *file, unsigned int cmd, unsigned long arg);
+
+#ifdef CONFIG_AUFS_RDU
+/* rdu.c */
+long au_rdu_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
+#ifdef CONFIG_COMPAT
+long au_rdu_compat_ioctl(struct file *file, unsigned int cmd,
+			 unsigned long arg);
+#endif
+#else
+AuStub(long, au_rdu_ioctl, return -EINVAL, struct file *file,
+       unsigned int cmd, unsigned long arg)
+#ifdef CONFIG_COMPAT
+AuStub(long, au_rdu_compat_ioctl, return -EINVAL, struct file *file,
+       unsigned int cmd, unsigned long arg)
+#endif
+#endif
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_DIR_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dirren.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dirren.c
@@ -0,0 +1,1315 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * special handling in renaming a directory
+ * in order to support looking-up the before-renamed name on the lower readonly
+ * branches
+ */
+
+#include <linux/byteorder/generic.h>
+#include "aufs.h"
+
+static void au_dr_hino_del(struct au_dr_br *dr, struct au_dr_hino *ent)
+{
+	int idx;
+
+	idx = au_dr_ihash(ent->dr_h_ino);
+	au_hbl_del(&ent->dr_hnode, dr->dr_h_ino + idx);
+}
+
+static int au_dr_hino_test_empty(struct au_dr_br *dr)
+{
+	int ret, i;
+	struct hlist_bl_head *hbl;
+
+	ret = 1;
+	for (i = 0; ret && i < AuDirren_NHASH; i++) {
+		hbl = dr->dr_h_ino + i;
+		hlist_bl_lock(hbl);
+		ret &= hlist_bl_empty(hbl);
+		hlist_bl_unlock(hbl);
+	}
+
+	return ret;
+}
+
+static struct au_dr_hino *au_dr_hino_find(struct au_dr_br *dr, ino_t ino)
+{
+	struct au_dr_hino *found, *ent;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	int idx;
+
+	found = NULL;
+	idx = au_dr_ihash(ino);
+	hbl = dr->dr_h_ino + idx;
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(ent, pos, hbl, dr_hnode)
+		if (ent->dr_h_ino == ino) {
+			found = ent;
+			break;
+		}
+	hlist_bl_unlock(hbl);
+
+	return found;
+}
+
+int au_dr_hino_test_add(struct au_dr_br *dr, ino_t ino,
+			struct au_dr_hino *add_ent)
+{
+	int found, idx;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	struct au_dr_hino *ent;
+
+	found = 0;
+	idx = au_dr_ihash(ino);
+	hbl = dr->dr_h_ino + idx;
+#if 0 /* debug print */
+	{
+		struct hlist_bl_node *tmp;
+
+		hlist_bl_for_each_entry_safe(ent, pos, tmp, hbl, dr_hnode)
+			AuDbg("hi%llu\n", (unsigned long long)ent->dr_h_ino);
+	}
+#endif
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(ent, pos, hbl, dr_hnode)
+		if (ent->dr_h_ino == ino) {
+			found = 1;
+			break;
+		}
+	if (!found && add_ent)
+		hlist_bl_add_head(&add_ent->dr_hnode, hbl);
+	hlist_bl_unlock(hbl);
+
+	if (!found && add_ent)
+		AuDbg("i%llu added\n", (unsigned long long)add_ent->dr_h_ino);
+
+	return found;
+}
+
+void au_dr_hino_free(struct au_dr_br *dr)
+{
+	int i;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos, *tmp;
+	struct au_dr_hino *ent;
+
+	/* SiMustWriteLock(sb); */
+
+	for (i = 0; i < AuDirren_NHASH; i++) {
+		hbl = dr->dr_h_ino + i;
+		/* no spinlock since sbinfo must be write-locked */
+		hlist_bl_for_each_entry_safe(ent, pos, tmp, hbl, dr_hnode)
+			au_kfree_rcu(ent);
+		INIT_HLIST_BL_HEAD(hbl);
+	}
+}
+
+/* returns the number of inodes or an error */
+static int au_dr_hino_store(struct super_block *sb, struct au_branch *br,
+			    struct file *hinofile)
+{
+	int err, i;
+	ssize_t ssz;
+	loff_t pos, oldsize;
+	__be64 u64;
+	struct inode *hinoinode;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *n1, *n2;
+	struct au_dr_hino *ent;
+
+	SiMustWriteLock(sb);
+	AuDebugOn(!au_br_writable(br->br_perm));
+
+	hinoinode = file_inode(hinofile);
+	oldsize = i_size_read(hinoinode);
+
+	err = 0;
+	pos = 0;
+	hbl = br->br_dirren.dr_h_ino;
+	for (i = 0; !err && i < AuDirren_NHASH; i++, hbl++) {
+		/* no bit-lock since sbinfo must be write-locked */
+		hlist_bl_for_each_entry_safe(ent, n1, n2, hbl, dr_hnode) {
+			AuDbg("hi%llu, %pD2\n",
+			      (unsigned long long)ent->dr_h_ino, hinofile);
+			u64 = cpu_to_be64(ent->dr_h_ino);
+			ssz = vfsub_write_k(hinofile, &u64, sizeof(u64), &pos);
+			if (ssz == sizeof(u64))
+				continue;
+
+			/* write error */
+			pr_err("ssz %zd, %pD2\n", ssz, hinofile);
+			err = -ENOSPC;
+			if (ssz < 0)
+				err = ssz;
+			break;
+		}
+	}
+	/* regardless the error */
+	if (pos < oldsize) {
+		err = vfsub_trunc(&hinofile->f_path, pos, /*attr*/0, hinofile);
+		AuTraceErr(err);
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_dr_hino_load(struct au_dr_br *dr, struct file *hinofile)
+{
+	int err, hidx;
+	ssize_t ssz;
+	size_t sz, n;
+	loff_t pos;
+	uint64_t u64;
+	struct au_dr_hino *ent;
+	struct inode *hinoinode;
+	struct hlist_bl_head *hbl;
+
+	err = 0;
+	pos = 0;
+	hbl = dr->dr_h_ino;
+	hinoinode = file_inode(hinofile);
+	sz = i_size_read(hinoinode);
+	AuDebugOn(sz % sizeof(u64));
+	n = sz / sizeof(u64);
+	while (n--) {
+		ssz = vfsub_read_k(hinofile, &u64, sizeof(u64), &pos);
+		if (unlikely(ssz != sizeof(u64))) {
+			pr_err("ssz %zd, %pD2\n", ssz, hinofile);
+			err = -EINVAL;
+			if (ssz < 0)
+				err = ssz;
+			goto out_free;
+		}
+
+		ent = kmalloc(sizeof(*ent), GFP_NOFS);
+		if (!ent) {
+			err = -ENOMEM;
+			AuTraceErr(err);
+			goto out_free;
+		}
+		ent->dr_h_ino = be64_to_cpu((__force __be64)u64);
+		AuDbg("hi%llu, %pD2\n",
+		      (unsigned long long)ent->dr_h_ino, hinofile);
+		hidx = au_dr_ihash(ent->dr_h_ino);
+		au_hbl_add(&ent->dr_hnode, hbl + hidx);
+	}
+	goto out; /* success */
+
+out_free:
+	au_dr_hino_free(dr);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * @bindex/@br is a switch to distinguish whether suspending hnotify or not.
+ * @path is a switch to distinguish load and store.
+ */
+static int au_dr_hino(struct super_block *sb, aufs_bindex_t bindex,
+		      struct au_branch *br, const struct path *path)
+{
+	int err, flags;
+	unsigned char load, suspend;
+	struct file *hinofile;
+	struct au_hinode *hdir;
+	struct inode *dir, *delegated;
+	struct path hinopath;
+	struct qstr hinoname = QSTR_INIT(AUFS_WH_DR_BRHINO,
+					 sizeof(AUFS_WH_DR_BRHINO) - 1);
+
+	AuDebugOn(bindex < 0 && !br);
+	AuDebugOn(bindex >= 0 && br);
+
+	err = -EINVAL;
+	suspend = !br;
+	if (suspend)
+		br = au_sbr(sb, bindex);
+	load = !!path;
+	if (!load) {
+		path = &br->br_path;
+		AuDebugOn(!au_br_writable(br->br_perm));
+		if (unlikely(!au_br_writable(br->br_perm)))
+			goto out;
+	}
+
+	hdir = NULL;
+	if (suspend) {
+		dir = d_inode(sb->s_root);
+		hdir = au_hinode(au_ii(dir), bindex);
+		dir = hdir->hi_inode;
+		au_hn_inode_lock_nested(hdir, AuLsc_I_CHILD);
+	} else {
+		dir = d_inode(path->dentry);
+		inode_lock_nested(dir, AuLsc_I_CHILD);
+	}
+	hinopath.mnt = path->mnt;
+	hinopath.dentry = vfsub_lkup_one(&hinoname, (struct path *)path);
+	err = PTR_ERR(hinopath.dentry);
+	if (IS_ERR(hinopath.dentry))
+		goto out_unlock;
+
+	err = 0;
+	flags = O_RDONLY;
+	if (load) {
+		if (d_is_negative(hinopath.dentry))
+			goto out_dput; /* success */
+	} else {
+		if (au_dr_hino_test_empty(&br->br_dirren)) {
+			if (d_is_positive(hinopath.dentry)) {
+				delegated = NULL;
+				err = vfsub_unlink(dir, &hinopath, &delegated,
+						   /*force*/0);
+				AuTraceErr(err);
+				if (unlikely(err))
+					pr_err("ignored err %d, %pd2\n",
+					       err, hinopath.dentry);
+				if (unlikely(err == -EWOULDBLOCK))
+					iput(delegated);
+				err = 0;
+			}
+			goto out_dput;
+		} else if (!d_is_positive(hinopath.dentry)) {
+			err = vfsub_create(dir, &hinopath, 0600,
+					   /*want_excl*/false);
+			AuTraceErr(err);
+			if (unlikely(err))
+				goto out_dput;
+		}
+		flags = O_WRONLY;
+	}
+	hinofile = vfsub_dentry_open(&hinopath, flags);
+	if (suspend)
+		au_hn_inode_unlock(hdir);
+	else
+		inode_unlock(dir);
+	dput(hinopath.dentry);
+	AuTraceErrPtr(hinofile);
+	if (IS_ERR(hinofile)) {
+		err = PTR_ERR(hinofile);
+		goto out;
+	}
+
+	if (load)
+		err = au_dr_hino_load(&br->br_dirren, hinofile);
+	else
+		err = au_dr_hino_store(sb, br, hinofile);
+	fput(hinofile);
+	goto out;
+
+out_dput:
+	dput(hinopath.dentry);
+out_unlock:
+	if (suspend)
+		au_hn_inode_unlock(hdir);
+	else
+		inode_unlock(dir);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_dr_brid_init(struct au_dr_brid *brid, const struct path *path)
+{
+	int err;
+	struct kstatfs kstfs;
+	dev_t dev;
+	struct dentry *dentry;
+	struct super_block *sb;
+
+	err = vfs_statfs((void *)path, &kstfs);
+	AuTraceErr(err);
+	if (unlikely(err))
+		goto out;
+
+	/* todo: support for UUID */
+
+	if (kstfs.f_fsid.val[0] || kstfs.f_fsid.val[1]) {
+		brid->type = AuBrid_FSID;
+		brid->fsid = kstfs.f_fsid;
+	} else {
+		dentry = path->dentry;
+		sb = dentry->d_sb;
+		dev = sb->s_dev;
+		if (dev) {
+			brid->type = AuBrid_DEV;
+			brid->dev = dev;
+		}
+	}
+
+out:
+	return err;
+}
+
+int au_dr_br_init(struct super_block *sb, struct au_branch *br,
+		  const struct path *path)
+{
+	int err, i;
+	struct au_dr_br *dr;
+	struct hlist_bl_head *hbl;
+
+	dr = &br->br_dirren;
+	hbl = dr->dr_h_ino;
+	for (i = 0; i < AuDirren_NHASH; i++, hbl++)
+		INIT_HLIST_BL_HEAD(hbl);
+
+	err = au_dr_brid_init(&dr->dr_brid, path);
+	if (unlikely(err))
+		goto out;
+
+	if (au_opt_test(au_mntflags(sb), DIRREN))
+		err = au_dr_hino(sb, /*bindex*/-1, br, path);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_dr_br_fin(struct super_block *sb, struct au_branch *br)
+{
+	int err;
+
+	err = 0;
+	if (au_br_writable(br->br_perm))
+		err = au_dr_hino(sb, /*bindex*/-1, br, /*path*/NULL);
+	if (!err)
+		au_dr_hino_free(&br->br_dirren);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_brid_str(struct au_dr_brid *brid, struct inode *h_inode,
+		       char *buf, size_t sz)
+{
+	int err;
+	unsigned int major, minor;
+	char *p;
+
+	p = buf;
+	err = snprintf(p, sz, "%d_", brid->type);
+	AuDebugOn(err > sz);
+	p += err;
+	sz -= err;
+	switch (brid->type) {
+	case AuBrid_Unset:
+		return -EINVAL;
+	case AuBrid_UUID:
+		err = snprintf(p, sz, "%pU", brid->uuid.b);
+		break;
+	case AuBrid_FSID:
+		err = snprintf(p, sz, "%08x-%08x",
+			       brid->fsid.val[0], brid->fsid.val[1]);
+		break;
+	case AuBrid_DEV:
+		major = MAJOR(brid->dev);
+		minor = MINOR(brid->dev);
+		if (major <= 0xff && minor <= 0xff)
+			err = snprintf(p, sz, "%02x%02x", major, minor);
+		else
+			err = snprintf(p, sz, "%03x:%05x", major, minor);
+		break;
+	}
+	AuDebugOn(err > sz);
+	p += err;
+	sz -= err;
+	err = snprintf(p, sz, "_%llu", (unsigned long long)h_inode->i_ino);
+	AuDebugOn(err > sz);
+	p += err;
+	sz -= err;
+
+	return p - buf;
+}
+
+static int au_drinfo_name(struct au_branch *br, char *name, int len)
+{
+	int rlen;
+	struct dentry *br_dentry;
+	struct inode *br_inode;
+
+	br_dentry = au_br_dentry(br);
+	br_inode = d_inode(br_dentry);
+	rlen = au_brid_str(&br->br_dirren.dr_brid, br_inode, name, len);
+	AuDebugOn(rlen >= AUFS_DIRREN_ENV_VAL_SZ);
+	AuDebugOn(rlen > len);
+
+	return rlen;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * from the given @h_dentry, construct drinfo at @*fdata.
+ * when the size of @*fdata is not enough, reallocate and return new @fdata and
+ * @allocated.
+ */
+static int au_drinfo_construct(struct au_drinfo_fdata **fdata,
+			       struct dentry *h_dentry,
+			       unsigned char *allocated)
+{
+	int err, v;
+	struct au_drinfo_fdata *f, *p;
+	struct au_drinfo *drinfo;
+	struct inode *h_inode;
+	struct qstr *qname;
+
+	err = 0;
+	f = *fdata;
+	h_inode = d_inode(h_dentry);
+	qname = &h_dentry->d_name;
+	drinfo = &f->drinfo;
+	drinfo->ino = (__force uint64_t)cpu_to_be64(h_inode->i_ino);
+	drinfo->oldnamelen = qname->len;
+	if (*allocated < sizeof(*f) + qname->len) {
+		v = roundup_pow_of_two(*allocated + qname->len);
+		p = au_krealloc(f, v, GFP_NOFS, /*may_shrink*/0);
+		if (unlikely(!p)) {
+			err = -ENOMEM;
+			AuTraceErr(err);
+			goto out;
+		}
+		f = p;
+		*fdata = f;
+		*allocated = v;
+		drinfo = &f->drinfo;
+	}
+	memcpy(drinfo->oldname, qname->name, qname->len);
+	AuDbg("i%llu, %.*s\n",
+	      be64_to_cpu((__force __be64)drinfo->ino), drinfo->oldnamelen,
+	      drinfo->oldname);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* callers have to free the return value */
+static struct au_drinfo *au_drinfo_read_k(struct file *file, ino_t h_ino)
+{
+	struct au_drinfo *ret, *drinfo;
+	struct au_drinfo_fdata fdata;
+	int len;
+	loff_t pos;
+	ssize_t ssz;
+
+	ret = ERR_PTR(-EIO);
+	pos = 0;
+	ssz = vfsub_read_k(file, &fdata, sizeof(fdata), &pos);
+	if (unlikely(ssz != sizeof(fdata))) {
+		AuIOErr("ssz %zd, %u, %pD2\n",
+			ssz, (unsigned int)sizeof(fdata), file);
+		goto out;
+	}
+
+	fdata.magic = ntohl((__force __be32)fdata.magic);
+	switch (fdata.magic) {
+	case AUFS_DRINFO_MAGIC_V1:
+		break;
+	default:
+		AuIOErr("magic-num 0x%x, 0x%x, %pD2\n",
+			fdata.magic, AUFS_DRINFO_MAGIC_V1, file);
+		goto out;
+	}
+
+	drinfo = &fdata.drinfo;
+	len = drinfo->oldnamelen;
+	if (!len) {
+		AuIOErr("broken drinfo %pD2\n", file);
+		goto out;
+	}
+
+	ret = NULL;
+	drinfo->ino = be64_to_cpu((__force __be64)drinfo->ino);
+	if (unlikely(h_ino && drinfo->ino != h_ino)) {
+		AuDbg("ignored i%llu, i%llu, %pD2\n",
+		      (unsigned long long)drinfo->ino,
+		      (unsigned long long)h_ino, file);
+		goto out; /* success */
+	}
+
+	ret = kmalloc(sizeof(*ret) + len, GFP_NOFS);
+	if (unlikely(!ret)) {
+		ret = ERR_PTR(-ENOMEM);
+		AuTraceErrPtr(ret);
+		goto out;
+	}
+
+	*ret = *drinfo;
+	ssz = vfsub_read_k(file, (void *)ret->oldname, len, &pos);
+	if (unlikely(ssz != len)) {
+		au_kfree_rcu(ret);
+		ret = ERR_PTR(-EIO);
+		AuIOErr("ssz %zd, %u, %pD2\n", ssz, len, file);
+		goto out;
+	}
+
+	AuDbg("oldname %.*s\n", ret->oldnamelen, ret->oldname);
+
+out:
+	return ret;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* in order to be revertible */
+struct au_drinfo_rev_elm {
+	int			created;
+	struct dentry		*info_dentry;
+	struct au_drinfo	*info_last;
+};
+
+struct au_drinfo_rev {
+	unsigned char			already;
+	aufs_bindex_t			nelm;
+	struct au_drinfo_rev_elm	elm[];
+};
+
+/* todo: isn't it too large? */
+struct au_drinfo_store {
+	struct path h_ppath;
+	struct dentry *h_dentry;
+	struct au_drinfo_fdata *fdata;
+	char *infoname;			/* inside of whname, just after PFX */
+	char whname[sizeof(AUFS_WH_DR_INFO_PFX) + AUFS_DIRREN_ENV_VAL_SZ];
+	aufs_bindex_t btgt, btail;
+	unsigned char no_sio,
+		allocated,		/* current size of *fdata */
+		infonamelen,		/* room size for p */
+		whnamelen,		/* length of the generated name */
+		renameback;		/* renamed back */
+};
+
+/* on rename(2) error, the caller should revert it using @elm */
+static int au_drinfo_do_store(struct au_drinfo_store *w,
+			      struct au_drinfo_rev_elm *elm)
+{
+	int err, len;
+	ssize_t ssz;
+	loff_t pos;
+	struct path infopath = {
+		.mnt = w->h_ppath.mnt
+	};
+	struct inode *h_dir, *h_inode, *delegated;
+	struct file *infofile;
+	struct qstr *qname;
+
+	AuDebugOn(elm
+		  && memcmp(elm, page_address(ZERO_PAGE(0)), sizeof(*elm)));
+
+	infopath.dentry = vfsub_lookup_one_len(w->whname, &w->h_ppath,
+					       w->whnamelen);
+	AuTraceErrPtr(infopath.dentry);
+	if (IS_ERR(infopath.dentry)) {
+		err = PTR_ERR(infopath.dentry);
+		goto out;
+	}
+
+	err = 0;
+	h_dir = d_inode(w->h_ppath.dentry);
+	if (elm && d_is_negative(infopath.dentry)) {
+		err = vfsub_create(h_dir, &infopath, 0600, /*want_excl*/true);
+		AuTraceErr(err);
+		if (unlikely(err))
+			goto out_dput;
+		elm->created = 1;
+		elm->info_dentry = dget(infopath.dentry);
+	}
+
+	infofile = vfsub_dentry_open(&infopath, O_RDWR);
+	AuTraceErrPtr(infofile);
+	if (IS_ERR(infofile)) {
+		err = PTR_ERR(infofile);
+		goto out_dput;
+	}
+
+	h_inode = d_inode(infopath.dentry);
+	if (elm && i_size_read(h_inode)) {
+		h_inode = d_inode(w->h_dentry);
+		elm->info_last = au_drinfo_read_k(infofile, h_inode->i_ino);
+		AuTraceErrPtr(elm->info_last);
+		if (IS_ERR(elm->info_last)) {
+			err = PTR_ERR(elm->info_last);
+			elm->info_last = NULL;
+			AuDebugOn(elm->info_dentry);
+			goto out_fput;
+		}
+	}
+
+	if (elm && w->renameback) {
+		delegated = NULL;
+		err = vfsub_unlink(h_dir, &infopath, &delegated, /*force*/0);
+		AuTraceErr(err);
+		if (unlikely(err == -EWOULDBLOCK))
+			iput(delegated);
+		goto out_fput;
+	}
+
+	pos = 0;
+	qname = &w->h_dentry->d_name;
+	len = sizeof(*w->fdata) + qname->len;
+	if (!elm)
+		len = sizeof(*w->fdata) + w->fdata->drinfo.oldnamelen;
+	ssz = vfsub_write_k(infofile, w->fdata, len, &pos);
+	if (ssz == len) {
+		AuDbg("hi%llu, %.*s\n", w->fdata->drinfo.ino,
+		      w->fdata->drinfo.oldnamelen, w->fdata->drinfo.oldname);
+		goto out_fput; /* success */
+	} else {
+		err = -EIO;
+		if (ssz < 0)
+			err = ssz;
+		/* the caller should revert it using @elm */
+	}
+
+out_fput:
+	fput(infofile);
+out_dput:
+	dput(infopath.dentry);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+struct au_call_drinfo_do_store_args {
+	int *errp;
+	struct au_drinfo_store *w;
+	struct au_drinfo_rev_elm *elm;
+};
+
+static void au_call_drinfo_do_store(void *args)
+{
+	struct au_call_drinfo_do_store_args *a = args;
+
+	*a->errp = au_drinfo_do_store(a->w, a->elm);
+}
+
+static int au_drinfo_store_sio(struct au_drinfo_store *w,
+			       struct au_drinfo_rev_elm *elm)
+{
+	int err, wkq_err;
+
+	if (w->no_sio)
+		err = au_drinfo_do_store(w, elm);
+	else {
+		struct au_call_drinfo_do_store_args a = {
+			.errp	= &err,
+			.w	= w,
+			.elm	= elm
+		};
+		wkq_err = au_wkq_wait(au_call_drinfo_do_store, &a);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+	AuTraceErr(err);
+
+	return err;
+}
+
+static int au_drinfo_store_work_init(struct au_drinfo_store *w,
+				     aufs_bindex_t btgt)
+{
+	int err;
+
+	memset(w, 0, sizeof(*w));
+	w->allocated = roundup_pow_of_two(sizeof(*w->fdata) + 40);
+	strcpy(w->whname, AUFS_WH_DR_INFO_PFX);
+	w->infoname = w->whname + sizeof(AUFS_WH_DR_INFO_PFX) - 1;
+	w->infonamelen = sizeof(w->whname) - sizeof(AUFS_WH_DR_INFO_PFX);
+	w->btgt = btgt;
+	w->no_sio = !!uid_eq(current_fsuid(), GLOBAL_ROOT_UID);
+
+	err = -ENOMEM;
+	w->fdata = kcalloc(1, w->allocated, GFP_NOFS);
+	if (unlikely(!w->fdata)) {
+		AuTraceErr(err);
+		goto out;
+	}
+	w->fdata->magic = (__force uint32_t)htonl(AUFS_DRINFO_MAGIC_V1);
+	err = 0;
+
+out:
+	return err;
+}
+
+static void au_drinfo_store_work_fin(struct au_drinfo_store *w)
+{
+	au_kfree_rcu(w->fdata);
+}
+
+static void au_drinfo_store_rev(struct au_drinfo_rev *rev,
+				struct au_drinfo_store *w)
+{
+	struct au_drinfo_rev_elm *elm;
+	struct inode *h_dir, *delegated;
+	int err, nelm;
+	struct path infopath = {
+		.mnt = w->h_ppath.mnt
+	};
+
+	h_dir = d_inode(w->h_ppath.dentry);
+	IMustLock(h_dir);
+
+	err = 0;
+	elm = rev->elm;
+	for (nelm = rev->nelm; nelm > 0; nelm--, elm++) {
+		AuDebugOn(elm->created && elm->info_last);
+		if (elm->created) {
+			AuDbg("here\n");
+			delegated = NULL;
+			infopath.dentry = elm->info_dentry;
+			err = vfsub_unlink(h_dir, &infopath, &delegated,
+					   !w->no_sio);
+			AuTraceErr(err);
+			if (unlikely(err == -EWOULDBLOCK))
+				iput(delegated);
+			dput(elm->info_dentry);
+		} else if (elm->info_last) {
+			AuDbg("here\n");
+			w->fdata->drinfo = *elm->info_last;
+			memcpy(w->fdata->drinfo.oldname,
+			       elm->info_last->oldname,
+			       elm->info_last->oldnamelen);
+			err = au_drinfo_store_sio(w, /*elm*/NULL);
+			au_kfree_rcu(elm->info_last);
+		}
+		if (unlikely(err))
+			AuIOErr("%d, %s\n", err, w->whname);
+		/* go on even if err */
+	}
+}
+
+/* caller has to call au_dr_rename_fin() later */
+static int au_drinfo_store(struct dentry *dentry, aufs_bindex_t btgt,
+			   struct qstr *dst_name, void *_rev)
+{
+	int err, sz, nelm;
+	aufs_bindex_t bindex, btail;
+	struct au_drinfo_store work;
+	struct au_drinfo_rev *rev, **p;
+	struct au_drinfo_rev_elm *elm;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_hinode *hdir;
+
+	err = au_drinfo_store_work_init(&work, btgt);
+	AuTraceErr(err);
+	if (unlikely(err))
+		goto out;
+
+	err = -ENOMEM;
+	btail = au_dbtaildir(dentry);
+	nelm = btail - btgt;
+	sz = sizeof(*rev) + sizeof(*elm) * nelm;
+	rev = kcalloc(1, sz, GFP_NOFS);
+	if (unlikely(!rev)) {
+		AuTraceErr(err);
+		goto out_args;
+	}
+	rev->nelm = nelm;
+	elm = rev->elm;
+	p = _rev;
+	*p = rev;
+
+	err = 0;
+	sb = dentry->d_sb;
+	work.h_ppath.dentry = au_h_dptr(dentry, btgt);
+	work.h_ppath.mnt = au_sbr_mnt(sb, btgt);
+	hdir = au_hi(d_inode(dentry), btgt);
+	au_hn_inode_lock_nested(hdir, AuLsc_I_CHILD);
+	for (bindex = btgt + 1; bindex <= btail; bindex++, elm++) {
+		work.h_dentry = au_h_dptr(dentry, bindex);
+		if (!work.h_dentry)
+			continue;
+
+		err = au_drinfo_construct(&work.fdata, work.h_dentry,
+					  &work.allocated);
+		AuTraceErr(err);
+		if (unlikely(err))
+			break;
+
+		work.renameback = au_qstreq(&work.h_dentry->d_name, dst_name);
+		br = au_sbr(sb, bindex);
+		work.whnamelen = sizeof(AUFS_WH_DR_INFO_PFX) - 1;
+		work.whnamelen += au_drinfo_name(br, work.infoname,
+						 work.infonamelen);
+		AuDbg("whname %.*s, i%llu, %.*s\n",
+		      work.whnamelen, work.whname,
+		      be64_to_cpu((__force __be64)work.fdata->drinfo.ino),
+		      work.fdata->drinfo.oldnamelen,
+		      work.fdata->drinfo.oldname);
+
+		err = au_drinfo_store_sio(&work, elm);
+		AuTraceErr(err);
+		if (unlikely(err))
+			break;
+	}
+	if (unlikely(err)) {
+		/* revert all drinfo */
+		au_drinfo_store_rev(rev, &work);
+		au_kfree_try_rcu(rev);
+		*p = NULL;
+	}
+	au_hn_inode_unlock(hdir);
+
+out_args:
+	au_drinfo_store_work_fin(&work);
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_dr_rename(struct dentry *src, aufs_bindex_t bindex,
+		 struct qstr *dst_name, void *_rev)
+{
+	int err, already;
+	ino_t ino;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_dr_br *dr;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	struct au_dr_hino *ent;
+	struct au_drinfo_rev *rev, **p;
+
+	AuDbg("bindex %d\n", bindex);
+
+	err = -ENOMEM;
+	ent = kmalloc(sizeof(*ent), GFP_NOFS);
+	if (unlikely(!ent))
+		goto out;
+
+	sb = src->d_sb;
+	br = au_sbr(sb, bindex);
+	dr = &br->br_dirren;
+	h_dentry = au_h_dptr(src, bindex);
+	h_inode = d_inode(h_dentry);
+	ino = h_inode->i_ino;
+	ent->dr_h_ino = ino;
+	already = au_dr_hino_test_add(dr, ino, ent);
+	AuDbg("b%d, hi%llu, already %d\n",
+	      bindex, (unsigned long long)ino, already);
+
+	err = au_drinfo_store(src, bindex, dst_name, _rev);
+	AuTraceErr(err);
+	if (!err) {
+		p = _rev;
+		rev = *p;
+		rev->already = already;
+		goto out; /* success */
+	}
+
+	/* revert */
+	if (!already)
+		au_dr_hino_del(dr, ent);
+	au_kfree_rcu(ent);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+void au_dr_rename_fin(struct dentry *src, aufs_bindex_t btgt, void *_rev)
+{
+	struct au_drinfo_rev *rev;
+	struct au_drinfo_rev_elm *elm;
+	int nelm;
+
+	rev = _rev;
+	elm = rev->elm;
+	for (nelm = rev->nelm; nelm > 0; nelm--, elm++) {
+		dput(elm->info_dentry);
+		au_kfree_rcu(elm->info_last);
+	}
+	au_kfree_try_rcu(rev);
+}
+
+void au_dr_rename_rev(struct dentry *src, aufs_bindex_t btgt, void *_rev)
+{
+	int err;
+	struct au_drinfo_store work;
+	struct au_drinfo_rev *rev = _rev;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct inode *h_inode;
+	struct au_dr_br *dr;
+	struct au_dr_hino *ent;
+
+	err = au_drinfo_store_work_init(&work, btgt);
+	if (unlikely(err))
+		goto out;
+
+	sb = src->d_sb;
+	br = au_sbr(sb, btgt);
+	work.h_ppath.dentry = au_h_dptr(src, btgt);
+	work.h_ppath.mnt = au_br_mnt(br);
+	au_drinfo_store_rev(rev, &work);
+	au_drinfo_store_work_fin(&work);
+	if (rev->already)
+		goto out;
+
+	dr = &br->br_dirren;
+	h_inode = d_inode(work.h_ppath.dentry);
+	ent = au_dr_hino_find(dr, h_inode->i_ino);
+	BUG_ON(!ent);
+	au_dr_hino_del(dr, ent);
+	au_kfree_rcu(ent);
+
+out:
+	au_kfree_try_rcu(rev);
+	if (unlikely(err))
+		pr_err("failed to remove dirren info\n");
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct au_drinfo *au_drinfo_do_load(struct path *h_ppath,
+					   char *whname, int whnamelen,
+					   struct dentry **info_dentry)
+{
+	struct au_drinfo *drinfo;
+	struct file *f;
+	struct inode *h_dir;
+	struct path infopath;
+	int unlocked;
+
+	AuDbg("%pd/%.*s\n", h_ppath->dentry, whnamelen, whname);
+
+	*info_dentry = NULL;
+	drinfo = NULL;
+	unlocked = 0;
+	h_dir = d_inode(h_ppath->dentry);
+	inode_lock_shared_nested(h_dir, AuLsc_I_PARENT);
+	infopath.dentry = vfsub_lookup_one_len(whname, h_ppath, whnamelen);
+	if (IS_ERR(infopath.dentry)) {
+		drinfo = (void *)infopath.dentry;
+		goto out;
+	}
+
+	if (d_is_negative(infopath.dentry))
+		goto out_dput; /* success */
+
+	infopath.mnt = h_ppath->mnt;
+	f = vfsub_dentry_open(&infopath, O_RDONLY);
+	inode_unlock_shared(h_dir);
+	unlocked = 1;
+	if (IS_ERR(f)) {
+		drinfo = (void *)f;
+		goto out_dput;
+	}
+
+	drinfo = au_drinfo_read_k(f, /*h_ino*/0);
+	if (IS_ERR_OR_NULL(drinfo))
+		goto out_fput;
+
+	AuDbg("oldname %.*s\n", drinfo->oldnamelen, drinfo->oldname);
+	*info_dentry = dget(infopath.dentry); /* keep it alive */
+
+out_fput:
+	fput(f);
+out_dput:
+	dput(infopath.dentry);
+out:
+	if (!unlocked)
+		inode_unlock_shared(h_dir);
+	AuTraceErrPtr(drinfo);
+	return drinfo;
+}
+
+struct au_drinfo_do_load_args {
+	struct au_drinfo **drinfop;
+	struct path *h_ppath;
+	char *whname;
+	int whnamelen;
+	struct dentry **info_dentry;
+};
+
+static void au_call_drinfo_do_load(void *args)
+{
+	struct au_drinfo_do_load_args *a = args;
+
+	*a->drinfop = au_drinfo_do_load(a->h_ppath, a->whname, a->whnamelen,
+					a->info_dentry);
+}
+
+struct au_drinfo_load {
+	struct path h_ppath;
+	struct qstr *qname;
+	unsigned char no_sio;
+
+	aufs_bindex_t ninfo;
+	struct au_drinfo **drinfo;
+};
+
+static int au_drinfo_load(struct au_drinfo_load *w, aufs_bindex_t bindex,
+			  struct au_branch *br)
+{
+	int err, wkq_err, whnamelen, e;
+	char whname[sizeof(AUFS_WH_DR_INFO_PFX) + AUFS_DIRREN_ENV_VAL_SZ]
+		= AUFS_WH_DR_INFO_PFX;
+	struct au_drinfo *drinfo;
+	struct qstr oldname;
+	struct inode *h_dir, *delegated;
+	struct dentry *info_dentry;
+	struct path infopath;
+
+	whnamelen = sizeof(AUFS_WH_DR_INFO_PFX) - 1;
+	whnamelen += au_drinfo_name(br, whname + whnamelen,
+				    sizeof(whname) - whnamelen);
+	if (w->no_sio)
+		drinfo = au_drinfo_do_load(&w->h_ppath, whname, whnamelen,
+					   &info_dentry);
+	else {
+		struct au_drinfo_do_load_args args = {
+			.drinfop	= &drinfo,
+			.h_ppath	= &w->h_ppath,
+			.whname		= whname,
+			.whnamelen	= whnamelen,
+			.info_dentry	= &info_dentry
+		};
+		wkq_err = au_wkq_wait(au_call_drinfo_do_load, &args);
+		if (unlikely(wkq_err))
+			drinfo = ERR_PTR(wkq_err);
+	}
+	err = PTR_ERR(drinfo);
+	if (IS_ERR_OR_NULL(drinfo))
+		goto out;
+
+	err = 0;
+	oldname.len = drinfo->oldnamelen;
+	oldname.name = drinfo->oldname;
+	if (au_qstreq(w->qname, &oldname)) {
+		/* the name is renamed back */
+		au_kfree_rcu(drinfo);
+		drinfo = NULL;
+
+		infopath.dentry = info_dentry;
+		infopath.mnt = w->h_ppath.mnt;
+		h_dir = d_inode(w->h_ppath.dentry);
+		delegated = NULL;
+		inode_lock_nested(h_dir, AuLsc_I_PARENT);
+		e = vfsub_unlink(h_dir, &infopath, &delegated, !w->no_sio);
+		inode_unlock(h_dir);
+		if (unlikely(e))
+			AuIOErr("ignored %d, %pd2\n", e, &infopath.dentry);
+		if (unlikely(e == -EWOULDBLOCK))
+			iput(delegated);
+	}
+	au_kfree_rcu(w->drinfo[bindex]);
+	w->drinfo[bindex] = drinfo;
+	dput(info_dentry);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void au_dr_lkup_free(struct au_drinfo **drinfo, int n)
+{
+	struct au_drinfo **p = drinfo;
+
+	while (n-- > 0)
+		au_kfree_rcu(*drinfo++);
+	au_kfree_try_rcu(p);
+}
+
+int au_dr_lkup(struct au_do_lookup_args *lkup, struct dentry *dentry,
+	       aufs_bindex_t btgt)
+{
+	int err, ninfo;
+	struct au_drinfo_load w;
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+	struct inode *h_dir;
+	struct au_dr_hino *ent;
+	struct super_block *sb;
+
+	AuDbg("%.*s, name %.*s, whname %.*s, b%d\n",
+	      AuLNPair(&dentry->d_name), AuLNPair(&lkup->dirren.dr_name),
+	      AuLNPair(&lkup->whname), btgt);
+
+	sb = dentry->d_sb;
+	bbot = au_sbbot(sb);
+	w.ninfo = bbot + 1;
+	if (!lkup->dirren.drinfo) {
+		lkup->dirren.drinfo = kcalloc(w.ninfo,
+					      sizeof(*lkup->dirren.drinfo),
+					      GFP_NOFS);
+		if (unlikely(!lkup->dirren.drinfo)) {
+			err = -ENOMEM;
+			goto out;
+		}
+		lkup->dirren.ninfo = w.ninfo;
+	}
+	w.drinfo = lkup->dirren.drinfo;
+	w.no_sio = !!uid_eq(current_fsuid(), GLOBAL_ROOT_UID);
+	w.h_ppath.dentry = au_h_dptr(dentry, btgt);
+	AuDebugOn(!w.h_ppath.dentry);
+	w.h_ppath.mnt = au_sbr_mnt(sb, btgt);
+	w.qname = &dentry->d_name;
+
+	ninfo = 0;
+	for (bindex = btgt + 1; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		err = au_drinfo_load(&w, bindex, br);
+		if (unlikely(err))
+			goto out_free;
+		if (w.drinfo[bindex])
+			ninfo++;
+	}
+	if (!ninfo) {
+		br = au_sbr(sb, btgt);
+		h_dir = d_inode(w.h_ppath.dentry);
+		ent = au_dr_hino_find(&br->br_dirren, h_dir->i_ino);
+		AuDebugOn(!ent);
+		au_dr_hino_del(&br->br_dirren, ent);
+		au_kfree_rcu(ent);
+	}
+	goto out; /* success */
+
+out_free:
+	au_dr_lkup_free(lkup->dirren.drinfo, lkup->dirren.ninfo);
+	lkup->dirren.ninfo = 0;
+	lkup->dirren.drinfo = NULL;
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+void au_dr_lkup_fin(struct au_do_lookup_args *lkup)
+{
+	au_dr_lkup_free(lkup->dirren.drinfo, lkup->dirren.ninfo);
+}
+
+int au_dr_lkup_name(struct au_do_lookup_args *lkup, aufs_bindex_t btgt)
+{
+	int err;
+	struct au_drinfo *drinfo;
+
+	err = 0;
+	if (!lkup->dirren.drinfo)
+		goto out;
+	AuDebugOn(lkup->dirren.ninfo <= btgt);
+	drinfo = lkup->dirren.drinfo[btgt];
+	if (!drinfo)
+		goto out;
+
+	au_kfree_try_rcu(lkup->whname.name);
+	lkup->whname.name = NULL;
+	lkup->dirren.dr_name.len = drinfo->oldnamelen;
+	lkup->dirren.dr_name.name = drinfo->oldname;
+	lkup->name = &lkup->dirren.dr_name;
+	err = au_wh_name_alloc(&lkup->whname, lkup->name);
+	if (!err)
+		AuDbg("name %.*s, whname %.*s, b%d\n",
+		      AuLNPair(lkup->name), AuLNPair(&lkup->whname),
+		      btgt);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_dr_lkup_h_ino(struct au_do_lookup_args *lkup, aufs_bindex_t bindex,
+		     ino_t h_ino)
+{
+	int match;
+	struct au_drinfo *drinfo;
+
+	match = 1;
+	if (!lkup->dirren.drinfo)
+		goto out;
+	AuDebugOn(lkup->dirren.ninfo <= bindex);
+	drinfo = lkup->dirren.drinfo[bindex];
+	if (!drinfo)
+		goto out;
+
+	match = (drinfo->ino == h_ino);
+	AuDbg("match %d\n", match);
+
+out:
+	return match;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_dr_opt_set(struct super_block *sb)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+
+	err = 0;
+	bbot = au_sbbot(sb);
+	for (bindex = 0; !err && bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		err = au_dr_hino(sb, bindex, /*br*/NULL, &br->br_path);
+	}
+
+	return err;
+}
+
+int au_dr_opt_flush(struct super_block *sb)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+
+	err = 0;
+	bbot = au_sbbot(sb);
+	for (bindex = 0; !err && bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (au_br_writable(br->br_perm))
+			err = au_dr_hino(sb, bindex, /*br*/NULL, /*path*/NULL);
+	}
+
+	return err;
+}
+
+int au_dr_opt_clr(struct super_block *sb, int no_flush)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+
+	err = 0;
+	if (!no_flush) {
+		err = au_dr_opt_flush(sb);
+		if (unlikely(err))
+			goto out;
+	}
+
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		au_dr_hino_free(&br->br_dirren);
+	}
+
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dirren.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dirren.h
@@ -0,0 +1,140 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2017-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * renamed dir info
+ */
+
+#ifndef __AUFS_DIRREN_H__
+#define __AUFS_DIRREN_H__
+
+#ifdef __KERNEL__
+
+#include <linux/dcache.h>
+#include <linux/statfs.h>
+#include <linux/uuid.h>
+#include "hbl.h"
+
+#define AuDirren_NHASH 100
+
+#ifdef CONFIG_AUFS_DIRREN
+enum au_brid_type {
+	AuBrid_Unset,
+	AuBrid_UUID,
+	AuBrid_FSID,
+	AuBrid_DEV
+};
+
+struct au_dr_brid {
+	enum au_brid_type	type;
+	union {
+		uuid_t	uuid;	/* unimplemented yet */
+		fsid_t	fsid;
+		dev_t	dev;
+	};
+};
+
+/* 20 is the max digits length of ulong 64 */
+/* brid-type "_" uuid "_" inum */
+#define AUFS_DIRREN_FNAME_SZ	(1 + 1 + UUID_STRING_LEN + 20)
+#define AUFS_DIRREN_ENV_VAL_SZ	(AUFS_DIRREN_FNAME_SZ + 1 + 20)
+
+struct au_dr_hino {
+	struct hlist_bl_node	dr_hnode;
+	ino_t			dr_h_ino;
+};
+
+struct au_dr_br {
+	struct hlist_bl_head	dr_h_ino[AuDirren_NHASH];
+	struct au_dr_brid	dr_brid;
+};
+
+struct au_dr_lookup {
+	/* dr_name is pointed by struct au_do_lookup_args.name */
+	struct qstr		dr_name; /* subset of dr_info */
+	aufs_bindex_t		ninfo;
+	struct au_drinfo	**drinfo;
+};
+#else
+struct au_dr_hino;
+/* empty */
+struct au_dr_br { };
+struct au_dr_lookup { };
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+struct au_branch;
+struct au_do_lookup_args;
+struct au_hinode;
+#ifdef CONFIG_AUFS_DIRREN
+int au_dr_hino_test_add(struct au_dr_br *dr, ino_t h_ino,
+			struct au_dr_hino *add_ent);
+void au_dr_hino_free(struct au_dr_br *dr);
+int au_dr_br_init(struct super_block *sb, struct au_branch *br,
+		  const struct path *path);
+int au_dr_br_fin(struct super_block *sb, struct au_branch *br);
+int au_dr_rename(struct dentry *src, aufs_bindex_t bindex,
+		 struct qstr *dst_name, void *_rev);
+void au_dr_rename_fin(struct dentry *src, aufs_bindex_t btgt, void *rev);
+void au_dr_rename_rev(struct dentry *src, aufs_bindex_t bindex, void *rev);
+int au_dr_lkup(struct au_do_lookup_args *lkup, struct dentry *dentry,
+	       aufs_bindex_t bindex);
+int au_dr_lkup_name(struct au_do_lookup_args *lkup, aufs_bindex_t btgt);
+int au_dr_lkup_h_ino(struct au_do_lookup_args *lkup, aufs_bindex_t bindex,
+		     ino_t h_ino);
+void au_dr_lkup_fin(struct au_do_lookup_args *lkup);
+int au_dr_opt_set(struct super_block *sb);
+int au_dr_opt_flush(struct super_block *sb);
+int au_dr_opt_clr(struct super_block *sb, int no_flush);
+#else
+AuStubInt0(au_dr_hino_test_add, struct au_dr_br *dr, ino_t h_ino,
+	   struct au_dr_hino *add_ent);
+AuStubVoid(au_dr_hino_free, struct au_dr_br *dr);
+AuStubInt0(au_dr_br_init, struct super_block *sb, struct au_branch *br,
+	   const struct path *path);
+AuStubInt0(au_dr_br_fin, struct super_block *sb, struct au_branch *br);
+AuStubInt0(au_dr_rename, struct dentry *src, aufs_bindex_t bindex,
+	   struct qstr *dst_name, void *_rev);
+AuStubVoid(au_dr_rename_fin, struct dentry *src, aufs_bindex_t btgt, void *rev);
+AuStubVoid(au_dr_rename_rev, struct dentry *src, aufs_bindex_t bindex,
+	   void *rev);
+AuStubInt0(au_dr_lkup, struct au_do_lookup_args *lkup, struct dentry *dentry,
+	   aufs_bindex_t bindex);
+AuStubInt0(au_dr_lkup_name, struct au_do_lookup_args *lkup, aufs_bindex_t btgt);
+AuStubInt0(au_dr_lkup_h_ino, struct au_do_lookup_args *lkup,
+	   aufs_bindex_t bindex, ino_t h_ino);
+AuStubVoid(au_dr_lkup_fin, struct au_do_lookup_args *lkup);
+AuStubInt0(au_dr_opt_set, struct super_block *sb);
+AuStubInt0(au_dr_opt_flush, struct super_block *sb);
+AuStubInt0(au_dr_opt_clr, struct super_block *sb, int no_flush);
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_DIRREN
+static inline int au_dr_ihash(ino_t h_ino)
+{
+	return h_ino % AuDirren_NHASH;
+}
+#else
+AuStubInt0(au_dr_ihash, ino_t h_ino);
+#endif
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_DIRREN_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dynop.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dynop.c
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2010-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * dynamically customizable operations for regular files
+ */
+
+#include "aufs.h"
+
+#define DyPrSym(key)	AuDbgSym(key->dk_op.dy_hop)
+
+/*
+ * How large will these lists be?
+ * Usually just a few elements, 20-30 at most for each, I guess.
+ */
+static struct hlist_bl_head dynop[AuDyLast];
+
+static struct au_dykey *dy_gfind_get(struct hlist_bl_head *hbl,
+				     const void *h_op)
+{
+	struct au_dykey *key, *tmp;
+	struct hlist_bl_node *pos;
+
+	key = NULL;
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(tmp, pos, hbl, dk_hnode)
+		if (tmp->dk_op.dy_hop == h_op) {
+			if (kref_get_unless_zero(&tmp->dk_kref))
+				key = tmp;
+			break;
+		}
+	hlist_bl_unlock(hbl);
+
+	return key;
+}
+
+static struct au_dykey *dy_bradd(struct au_branch *br, struct au_dykey *key)
+{
+	struct au_dykey **k, *found;
+	const void *h_op = key->dk_op.dy_hop;
+	int i;
+
+	found = NULL;
+	k = br->br_dykey;
+	for (i = 0; i < AuBrDynOp; i++)
+		if (k[i]) {
+			if (k[i]->dk_op.dy_hop == h_op) {
+				found = k[i];
+				break;
+			}
+		} else
+			break;
+	if (!found) {
+		spin_lock(&br->br_dykey_lock);
+		for (; i < AuBrDynOp; i++)
+			if (k[i]) {
+				if (k[i]->dk_op.dy_hop == h_op) {
+					found = k[i];
+					break;
+				}
+			} else {
+				k[i] = key;
+				break;
+			}
+		spin_unlock(&br->br_dykey_lock);
+		BUG_ON(i == AuBrDynOp); /* expand the array */
+	}
+
+	return found;
+}
+
+/* kref_get() if @key is already added */
+static struct au_dykey *dy_gadd(struct hlist_bl_head *hbl, struct au_dykey *key)
+{
+	struct au_dykey *tmp, *found;
+	struct hlist_bl_node *pos;
+	const void *h_op = key->dk_op.dy_hop;
+
+	found = NULL;
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(tmp, pos, hbl, dk_hnode)
+		if (tmp->dk_op.dy_hop == h_op) {
+			if (kref_get_unless_zero(&tmp->dk_kref))
+				found = tmp;
+			break;
+		}
+	if (!found)
+		hlist_bl_add_head(&key->dk_hnode, hbl);
+	hlist_bl_unlock(hbl);
+
+	if (!found)
+		DyPrSym(key);
+	return found;
+}
+
+static void dy_free_rcu(struct rcu_head *rcu)
+{
+	struct au_dykey *key;
+
+	key = container_of(rcu, struct au_dykey, dk_rcu);
+	DyPrSym(key);
+	kfree(key);
+}
+
+static void dy_free(struct kref *kref)
+{
+	struct au_dykey *key;
+	struct hlist_bl_head *hbl;
+
+	key = container_of(kref, struct au_dykey, dk_kref);
+	hbl = dynop + key->dk_op.dy_type;
+	au_hbl_del(&key->dk_hnode, hbl);
+	call_rcu(&key->dk_rcu, dy_free_rcu);
+}
+
+void au_dy_put(struct au_dykey *key)
+{
+	kref_put(&key->dk_kref, dy_free);
+}
+
+/* ---------------------------------------------------------------------- */
+
+#define DyDbgSize(cnt, op)	AuDebugOn(cnt != sizeof(op)/sizeof(void *))
+
+#ifdef CONFIG_AUFS_DEBUG
+#define DyDbgDeclare(cnt)	unsigned int cnt = 0
+#define DyDbgInc(cnt)		do { cnt++; } while (0)
+#else
+#define DyDbgDeclare(cnt)	do {} while (0)
+#define DyDbgInc(cnt)		do {} while (0)
+#endif
+
+#define DySet(func, dst, src, h_op, h_sb) do {				\
+	DyDbgInc(cnt);							\
+	if (h_op->func) {						\
+		if (src.func)						\
+			dst.func = src.func;				\
+		else							\
+			AuDbg("%s %s\n", au_sbtype(h_sb), #func);	\
+	}								\
+} while (0)
+
+#define DySetForce(func, dst, src) do {		\
+	AuDebugOn(!src.func);			\
+	DyDbgInc(cnt);				\
+	dst.func = src.func;			\
+} while (0)
+
+#define DySetAop(func) \
+	DySet(func, dyaop->da_op, aufs_aop, h_aop, h_sb)
+#define DySetAopForce(func) \
+	DySetForce(func, dyaop->da_op, aufs_aop)
+
+static void dy_aop(struct au_dykey *key, const void *h_op,
+		   struct super_block *h_sb __maybe_unused)
+{
+	struct au_dyaop *dyaop = (void *)key;
+	const struct address_space_operations *h_aop = h_op;
+	DyDbgDeclare(cnt);
+
+	AuDbg("%s\n", au_sbtype(h_sb));
+
+	DySetAop(writepage);
+	DySetAopForce(readpage);	/* force */
+	DySetAop(writepages);
+	DySetAop(set_page_dirty);
+	DySetAop(readpages);
+	DySetAop(readahead);
+	DySetAop(write_begin);
+	DySetAop(write_end);
+	DySetAop(bmap);
+	DySetAop(invalidatepage);
+	DySetAop(releasepage);
+	DySetAop(freepage);
+	/* this one will be changed according to an aufs mount option */
+	DySetAop(direct_IO);
+	DySetAop(migratepage);
+	DySetAop(isolate_page);
+	DySetAop(putback_page);
+	DySetAop(launder_page);
+	DySetAop(is_partially_uptodate);
+	DySetAop(is_dirty_writeback);
+	DySetAop(error_remove_page);
+	DySetAop(swap_activate);
+	DySetAop(swap_deactivate);
+
+	DyDbgSize(cnt, *h_aop);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void dy_bug(struct kref *kref)
+{
+	BUG();
+}
+
+static struct au_dykey *dy_get(struct au_dynop *op, struct au_branch *br)
+{
+	struct au_dykey *key, *old;
+	struct hlist_bl_head *hbl;
+	struct op {
+		unsigned int sz;
+		void (*set)(struct au_dykey *key, const void *h_op,
+			    struct super_block *h_sb __maybe_unused);
+	};
+	static const struct op a[] = {
+		[AuDy_AOP] = {
+			.sz	= sizeof(struct au_dyaop),
+			.set	= dy_aop
+		}
+	};
+	const struct op *p;
+
+	hbl = dynop + op->dy_type;
+	key = dy_gfind_get(hbl, op->dy_hop);
+	if (key)
+		goto out_add; /* success */
+
+	p = a + op->dy_type;
+	key = kzalloc(p->sz, GFP_NOFS);
+	if (unlikely(!key)) {
+		key = ERR_PTR(-ENOMEM);
+		goto out;
+	}
+
+	key->dk_op.dy_hop = op->dy_hop;
+	kref_init(&key->dk_kref);
+	p->set(key, op->dy_hop, au_br_sb(br));
+	old = dy_gadd(hbl, key);
+	if (old) {
+		au_kfree_rcu(key);
+		key = old;
+	}
+
+out_add:
+	old = dy_bradd(br, key);
+	if (old)
+		/* its ref-count should never be zero here */
+		kref_put(&key->dk_kref, dy_bug);
+out:
+	return key;
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * Aufs prohibits O_DIRECT by default even if the branch supports it.
+ * This behaviour is necessary to return an error from open(O_DIRECT) instead
+ * of the succeeding I/O. The dio mount option enables O_DIRECT and makes
+ * open(O_DIRECT) always succeed, but the succeeding I/O may return an error.
+ * See the aufs manual in detail.
+ */
+static void dy_adx(struct au_dyaop *dyaop, int do_dx)
+{
+	if (!do_dx)
+		dyaop->da_op.direct_IO = NULL;
+	else
+		dyaop->da_op.direct_IO = aufs_aop.direct_IO;
+}
+
+static struct au_dyaop *dy_aget(struct au_branch *br,
+				const struct address_space_operations *h_aop,
+				int do_dx)
+{
+	struct au_dyaop *dyaop;
+	struct au_dynop op;
+
+	op.dy_type = AuDy_AOP;
+	op.dy_haop = h_aop;
+	dyaop = (void *)dy_get(&op, br);
+	if (IS_ERR(dyaop))
+		goto out;
+	dy_adx(dyaop, do_dx);
+
+out:
+	return dyaop;
+}
+
+int au_dy_iaop(struct inode *inode, aufs_bindex_t bindex,
+		struct inode *h_inode)
+{
+	int err, do_dx;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_dyaop *dyaop;
+
+	AuDebugOn(!S_ISREG(h_inode->i_mode));
+	IiMustWriteLock(inode);
+
+	sb = inode->i_sb;
+	br = au_sbr(sb, bindex);
+	do_dx = !!au_opt_test(au_mntflags(sb), DIO);
+	dyaop = dy_aget(br, h_inode->i_mapping->a_ops, do_dx);
+	err = PTR_ERR(dyaop);
+	if (IS_ERR(dyaop))
+		/* unnecessary to call dy_fput() */
+		goto out;
+
+	err = 0;
+	inode->i_mapping->a_ops = &dyaop->da_op;
+
+out:
+	return err;
+}
+
+/*
+ * Is it safe to replace a_ops during the inode/file is in operation?
+ * Yes, I hope so.
+ */
+int au_dy_irefresh(struct inode *inode)
+{
+	int err;
+	aufs_bindex_t btop;
+	struct inode *h_inode;
+
+	err = 0;
+	if (S_ISREG(inode->i_mode)) {
+		btop = au_ibtop(inode);
+		h_inode = au_h_iptr(inode, btop);
+		err = au_dy_iaop(inode, btop, h_inode);
+	}
+	return err;
+}
+
+void au_dy_arefresh(int do_dx)
+{
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	struct au_dykey *key;
+
+	hbl = dynop + AuDy_AOP;
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(key, pos, hbl, dk_hnode)
+		dy_adx((void *)key, do_dx);
+	hlist_bl_unlock(hbl);
+}
+
+/* ---------------------------------------------------------------------- */
+
+void __init au_dy_init(void)
+{
+	int i;
+
+	for (i = 0; i < AuDyLast; i++)
+		INIT_HLIST_BL_HEAD(dynop + i);
+}
+
+void au_dy_fin(void)
+{
+	int i;
+
+	for (i = 0; i < AuDyLast; i++)
+		WARN_ON(!hlist_bl_empty(dynop + i));
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/dynop.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/dynop.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2010-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * dynamically customizable operations (for regular files only)
+ */
+
+#ifndef __AUFS_DYNOP_H__
+#define __AUFS_DYNOP_H__
+
+#ifdef __KERNEL__
+
+#include <linux/fs.h>
+#include <linux/kref.h>
+
+enum {AuDy_AOP, AuDyLast};
+
+struct au_dynop {
+	int						dy_type;
+	union {
+		const void				*dy_hop;
+		const struct address_space_operations	*dy_haop;
+	};
+};
+
+struct au_dykey {
+	union {
+		struct hlist_bl_node	dk_hnode;
+		struct rcu_head		dk_rcu;
+	};
+	struct au_dynop		dk_op;
+
+	/*
+	 * during I am in the branch local array, kref is gotten. when the
+	 * branch is removed, kref is put.
+	 */
+	struct kref		dk_kref;
+};
+
+/* stop unioning since their sizes are very different from each other */
+struct au_dyaop {
+	struct au_dykey			da_key;
+	struct address_space_operations	da_op; /* not const */
+};
+/* make sure that 'struct au_dykey *' can be any type */
+static_assert(!offsetof(struct au_dyaop, da_key));
+
+/* ---------------------------------------------------------------------- */
+
+/* dynop.c */
+struct au_branch;
+void au_dy_put(struct au_dykey *key);
+int au_dy_iaop(struct inode *inode, aufs_bindex_t bindex,
+		struct inode *h_inode);
+int au_dy_irefresh(struct inode *inode);
+void au_dy_arefresh(int do_dio);
+
+void __init au_dy_init(void);
+void au_dy_fin(void);
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_DYNOP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/export.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/export.c
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * export via nfs
+ */
+
+#include <linux/exportfs.h>
+#include <linux/fs_struct.h>
+#include <linux/namei.h>
+#include <linux/nsproxy.h>
+#include <linux/random.h>
+#include <linux/writeback.h>
+#include "aufs.h"
+
+union conv {
+#ifdef CONFIG_AUFS_INO_T_64
+	__u32 a[2];
+#else
+	__u32 a[1];
+#endif
+	ino_t ino;
+};
+
+static ino_t decode_ino(__u32 *a)
+{
+	union conv u;
+
+	BUILD_BUG_ON(sizeof(u.ino) != sizeof(u.a));
+	u.a[0] = a[0];
+#ifdef CONFIG_AUFS_INO_T_64
+	u.a[1] = a[1];
+#endif
+	return u.ino;
+}
+
+static void encode_ino(__u32 *a, ino_t ino)
+{
+	union conv u;
+
+	u.ino = ino;
+	a[0] = u.a[0];
+#ifdef CONFIG_AUFS_INO_T_64
+	a[1] = u.a[1];
+#endif
+}
+
+/* NFS file handle */
+enum {
+	Fh_br_id,
+	Fh_sigen,
+#ifdef CONFIG_AUFS_INO_T_64
+	/* support 64bit inode number */
+	Fh_ino1,
+	Fh_ino2,
+	Fh_dir_ino1,
+	Fh_dir_ino2,
+#else
+	Fh_ino1,
+	Fh_dir_ino1,
+#endif
+	Fh_igen,
+	Fh_h_type,
+	Fh_tail,
+
+	Fh_ino = Fh_ino1,
+	Fh_dir_ino = Fh_dir_ino1
+};
+
+static int au_test_anon(struct dentry *dentry)
+{
+	/* note: read d_flags without d_lock */
+	return !!(dentry->d_flags & DCACHE_DISCONNECTED);
+}
+
+int au_test_nfsd(void)
+{
+	int ret;
+	struct task_struct *tsk = current;
+	char comm[sizeof(tsk->comm)];
+
+	ret = 0;
+	if (tsk->flags & PF_KTHREAD) {
+		get_task_comm(comm, tsk);
+		ret = !strcmp(comm, "nfsd");
+	}
+
+	return ret;
+}
+
+/* ---------------------------------------------------------------------- */
+/* inode generation external table */
+
+void au_xigen_inc(struct inode *inode)
+{
+	loff_t pos;
+	ssize_t sz;
+	__u32 igen;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+
+	sb = inode->i_sb;
+	AuDebugOn(!au_opt_test(au_mntflags(sb), XINO));
+
+	sbinfo = au_sbi(sb);
+	pos = inode->i_ino;
+	pos *= sizeof(igen);
+	igen = inode->i_generation + 1;
+	sz = xino_fwrite(sbinfo->si_xigen, &igen, sizeof(igen), &pos);
+	if (sz == sizeof(igen))
+		return; /* success */
+
+	if (unlikely(sz >= 0))
+		AuIOErr("xigen error (%zd)\n", sz);
+}
+
+int au_xigen_new(struct inode *inode)
+{
+	int err;
+	loff_t pos;
+	ssize_t sz;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+	struct file *file;
+
+	err = 0;
+	/* todo: dirty, at mount time */
+	if (inode->i_ino == AUFS_ROOT_INO)
+		goto out;
+	sb = inode->i_sb;
+	SiMustAnyLock(sb);
+	if (unlikely(!au_opt_test(au_mntflags(sb), XINO)))
+		goto out;
+
+	err = -EFBIG;
+	pos = inode->i_ino;
+	if (unlikely(au_loff_max / sizeof(inode->i_generation) - 1 < pos)) {
+		AuIOErr1("too large i%lld\n", pos);
+		goto out;
+	}
+	pos *= sizeof(inode->i_generation);
+
+	err = 0;
+	sbinfo = au_sbi(sb);
+	file = sbinfo->si_xigen;
+	BUG_ON(!file);
+
+	if (vfsub_f_size_read(file)
+	    < pos + sizeof(inode->i_generation)) {
+		inode->i_generation = atomic_inc_return(&sbinfo->si_xigen_next);
+		sz = xino_fwrite(file, &inode->i_generation,
+				 sizeof(inode->i_generation), &pos);
+	} else
+		sz = xino_fread(file, &inode->i_generation,
+				sizeof(inode->i_generation), &pos);
+	if (sz == sizeof(inode->i_generation))
+		goto out; /* success */
+
+	err = sz;
+	if (unlikely(sz >= 0)) {
+		err = -EIO;
+		AuIOErr("xigen error (%zd)\n", sz);
+	}
+
+out:
+	return err;
+}
+
+int au_xigen_set(struct super_block *sb, struct path *path)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+	struct file *file;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	file = au_xino_create2(sb, path, sbinfo->si_xigen);
+	err = PTR_ERR(file);
+	if (IS_ERR(file))
+		goto out;
+	err = 0;
+	if (sbinfo->si_xigen)
+		fput(sbinfo->si_xigen);
+	sbinfo->si_xigen = file;
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+void au_xigen_clr(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	if (sbinfo->si_xigen) {
+		fput(sbinfo->si_xigen);
+		sbinfo->si_xigen = NULL;
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct dentry *decode_by_ino(struct super_block *sb, ino_t ino,
+				    ino_t dir_ino)
+{
+	struct dentry *dentry, *d;
+	struct inode *inode;
+	unsigned int sigen;
+
+	dentry = NULL;
+	inode = ilookup(sb, ino);
+	if (!inode)
+		goto out;
+
+	dentry = ERR_PTR(-ESTALE);
+	sigen = au_sigen(sb);
+	if (unlikely(au_is_bad_inode(inode)
+		     || IS_DEADDIR(inode)
+		     || sigen != au_iigen(inode, NULL)))
+		goto out_iput;
+
+	dentry = NULL;
+	if (!dir_ino || S_ISDIR(inode->i_mode))
+		dentry = d_find_alias(inode);
+	else {
+		spin_lock(&inode->i_lock);
+		hlist_for_each_entry(d, &inode->i_dentry, d_u.d_alias) {
+			spin_lock(&d->d_lock);
+			if (!au_test_anon(d)
+			    && d_inode(d->d_parent)->i_ino == dir_ino) {
+				dentry = dget_dlock(d);
+				spin_unlock(&d->d_lock);
+				break;
+			}
+			spin_unlock(&d->d_lock);
+		}
+		spin_unlock(&inode->i_lock);
+	}
+	if (unlikely(dentry && au_digen_test(dentry, sigen))) {
+		/* need to refresh */
+		dput(dentry);
+		dentry = NULL;
+	}
+
+out_iput:
+	iput(inode);
+out:
+	AuTraceErrPtr(dentry);
+	return dentry;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* todo: dirty? */
+/* if exportfs_decode_fh() passed vfsmount*, we could be happy */
+
+struct au_compare_mnt_args {
+	/* input */
+	struct super_block *sb;
+
+	/* output */
+	struct vfsmount *mnt;
+};
+
+static int au_compare_mnt(struct vfsmount *mnt, void *arg)
+{
+	struct au_compare_mnt_args *a = arg;
+
+	if (mnt->mnt_sb != a->sb)
+		return 0;
+	a->mnt = mntget(mnt);
+	return 1;
+}
+
+static struct vfsmount *au_mnt_get(struct super_block *sb)
+{
+	int err;
+	struct path root;
+	struct au_compare_mnt_args args = {
+		.sb = sb
+	};
+
+	get_fs_root(current->fs, &root);
+	rcu_read_lock();
+	err = iterate_mounts(au_compare_mnt, &args, root.mnt);
+	rcu_read_unlock();
+	path_put(&root);
+	AuDebugOn(!err);
+	AuDebugOn(!args.mnt);
+	return args.mnt;
+}
+
+struct au_nfsd_si_lock {
+	unsigned int sigen;
+	aufs_bindex_t bindex, br_id;
+	unsigned char force_lock;
+};
+
+static int si_nfsd_read_lock(struct super_block *sb,
+			     struct au_nfsd_si_lock *nsi_lock)
+{
+	int err;
+	aufs_bindex_t bindex;
+
+	si_read_lock(sb, AuLock_FLUSH);
+
+	/* branch id may be wrapped around */
+	err = 0;
+	bindex = au_br_index(sb, nsi_lock->br_id);
+	if (bindex >= 0 && nsi_lock->sigen + AUFS_BRANCH_MAX > au_sigen(sb))
+		goto out; /* success */
+
+	err = -ESTALE;
+	bindex = -1;
+	if (!nsi_lock->force_lock)
+		si_read_unlock(sb);
+
+out:
+	nsi_lock->bindex = bindex;
+	return err;
+}
+
+struct find_name_by_ino {
+	struct dir_context ctx;
+	int called, found;
+	ino_t ino;
+	char *name;
+	int namelen;
+};
+
+static int
+find_name_by_ino(struct dir_context *ctx, const char *name, int namelen,
+		 loff_t offset, u64 ino, unsigned int d_type)
+{
+	struct find_name_by_ino *a = container_of(ctx, struct find_name_by_ino,
+						  ctx);
+
+	a->called++;
+	if (a->ino != ino)
+		return 0;
+
+	memcpy(a->name, name, namelen);
+	a->namelen = namelen;
+	a->found = 1;
+	return 1;
+}
+
+static struct dentry *au_lkup_by_ino(struct path *path, ino_t ino,
+				     struct au_nfsd_si_lock *nsi_lock)
+{
+	struct dentry *dentry, *parent;
+	struct file *file;
+	struct inode *dir;
+	struct find_name_by_ino arg = {
+		.ctx = {
+			.actor = find_name_by_ino
+		}
+	};
+	int err;
+
+	parent = path->dentry;
+	if (nsi_lock)
+		si_read_unlock(parent->d_sb);
+	file = vfsub_dentry_open(path, au_dir_roflags);
+	dentry = (void *)file;
+	if (IS_ERR(file))
+		goto out;
+
+	dentry = ERR_PTR(-ENOMEM);
+	arg.name = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!arg.name))
+		goto out_file;
+	arg.ino = ino;
+	arg.found = 0;
+	do {
+		arg.called = 0;
+		/* smp_mb(); */
+		err = vfsub_iterate_dir(file, &arg.ctx);
+	} while (!err && !arg.found && arg.called);
+	dentry = ERR_PTR(err);
+	if (unlikely(err))
+		goto out_name;
+	/* instead of ENOENT */
+	dentry = ERR_PTR(-ESTALE);
+	if (!arg.found)
+		goto out_name;
+
+	/* do not call vfsub_lkup_one() */
+	dir = d_inode(parent);
+	dentry = vfsub_lookup_one_len_unlocked(arg.name, path, arg.namelen);
+	AuTraceErrPtr(dentry);
+	if (IS_ERR(dentry))
+		goto out_name;
+	AuDebugOn(au_test_anon(dentry));
+	if (unlikely(d_really_is_negative(dentry))) {
+		dput(dentry);
+		dentry = ERR_PTR(-ENOENT);
+	}
+
+out_name:
+	free_page((unsigned long)arg.name);
+out_file:
+	fput(file);
+out:
+	if (unlikely(nsi_lock
+		     && si_nfsd_read_lock(parent->d_sb, nsi_lock) < 0))
+		if (!IS_ERR(dentry)) {
+			dput(dentry);
+			dentry = ERR_PTR(-ESTALE);
+		}
+	AuTraceErrPtr(dentry);
+	return dentry;
+}
+
+static struct dentry *decode_by_dir_ino(struct super_block *sb, ino_t ino,
+					ino_t dir_ino,
+					struct au_nfsd_si_lock *nsi_lock)
+{
+	struct dentry *dentry;
+	struct path path;
+
+	if (dir_ino != AUFS_ROOT_INO) {
+		path.dentry = decode_by_ino(sb, dir_ino, 0);
+		dentry = path.dentry;
+		if (!path.dentry || IS_ERR(path.dentry))
+			goto out;
+		AuDebugOn(au_test_anon(path.dentry));
+	} else
+		path.dentry = dget(sb->s_root);
+
+	path.mnt = au_mnt_get(sb);
+	dentry = au_lkup_by_ino(&path, ino, nsi_lock);
+	path_put(&path);
+
+out:
+	AuTraceErrPtr(dentry);
+	return dentry;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int h_acceptable(void *expv, struct dentry *dentry)
+{
+	return 1;
+}
+
+static char *au_build_path(struct dentry *h_parent, struct path *h_rootpath,
+			   char *buf, int len, struct super_block *sb)
+{
+	char *p;
+	int n;
+	struct path path;
+
+	p = d_path(h_rootpath, buf, len);
+	if (IS_ERR(p))
+		goto out;
+	n = strlen(p);
+
+	path.mnt = h_rootpath->mnt;
+	path.dentry = h_parent;
+	p = d_path(&path, buf, len);
+	if (IS_ERR(p))
+		goto out;
+	if (n != 1)
+		p += n;
+
+	path.mnt = au_mnt_get(sb);
+	path.dentry = sb->s_root;
+	p = d_path(&path, buf, len - strlen(p));
+	mntput(path.mnt);
+	if (IS_ERR(p))
+		goto out;
+	if (n != 1)
+		p[strlen(p)] = '/';
+
+out:
+	AuTraceErrPtr(p);
+	return p;
+}
+
+static
+struct dentry *decode_by_path(struct super_block *sb, ino_t ino, __u32 *fh,
+			      int fh_len, struct au_nfsd_si_lock *nsi_lock)
+{
+	struct dentry *dentry, *h_parent, *root;
+	struct super_block *h_sb;
+	char *pathname, *p;
+	struct vfsmount *h_mnt;
+	struct au_branch *br;
+	int err;
+	struct path path;
+
+	br = au_sbr(sb, nsi_lock->bindex);
+	h_mnt = au_br_mnt(br);
+	h_sb = h_mnt->mnt_sb;
+	/* todo: call lower fh_to_dentry()? fh_to_parent()? */
+	lockdep_off();
+	h_parent = exportfs_decode_fh(h_mnt, (void *)(fh + Fh_tail),
+				      fh_len - Fh_tail, fh[Fh_h_type],
+				      h_acceptable, /*context*/NULL);
+	lockdep_on();
+	dentry = h_parent;
+	if (unlikely(!h_parent || IS_ERR(h_parent))) {
+		AuWarn1("%s decode_fh failed, %ld\n",
+			au_sbtype(h_sb), PTR_ERR(h_parent));
+		goto out;
+	}
+	dentry = NULL;
+	if (unlikely(au_test_anon(h_parent))) {
+		AuWarn1("%s decode_fh returned a disconnected dentry\n",
+			au_sbtype(h_sb));
+		goto out_h_parent;
+	}
+
+	dentry = ERR_PTR(-ENOMEM);
+	pathname = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!pathname))
+		goto out_h_parent;
+
+	root = sb->s_root;
+	path.mnt = h_mnt;
+	di_read_lock_parent(root, !AuLock_IR);
+	path.dentry = au_h_dptr(root, nsi_lock->bindex);
+	di_read_unlock(root, !AuLock_IR);
+	p = au_build_path(h_parent, &path, pathname, PAGE_SIZE, sb);
+	dentry = (void *)p;
+	if (IS_ERR(p))
+		goto out_pathname;
+
+	si_read_unlock(sb);
+	err = vfsub_kern_path(p, LOOKUP_FOLLOW | LOOKUP_DIRECTORY, &path);
+	dentry = ERR_PTR(err);
+	if (unlikely(err))
+		goto out_relock;
+
+	dentry = ERR_PTR(-ENOENT);
+	AuDebugOn(au_test_anon(path.dentry));
+	if (unlikely(d_really_is_negative(path.dentry)))
+		goto out_path;
+
+	if (ino != d_inode(path.dentry)->i_ino)
+		dentry = au_lkup_by_ino(&path, ino, /*nsi_lock*/NULL);
+	else
+		dentry = dget(path.dentry);
+
+out_path:
+	path_put(&path);
+out_relock:
+	if (unlikely(si_nfsd_read_lock(sb, nsi_lock) < 0))
+		if (!IS_ERR(dentry)) {
+			dput(dentry);
+			dentry = ERR_PTR(-ESTALE);
+		}
+out_pathname:
+	free_page((unsigned long)pathname);
+out_h_parent:
+	dput(h_parent);
+out:
+	AuTraceErrPtr(dentry);
+	return dentry;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct dentry *
+aufs_fh_to_dentry(struct super_block *sb, struct fid *fid, int fh_len,
+		  int fh_type)
+{
+	struct dentry *dentry;
+	__u32 *fh = fid->raw;
+	struct au_branch *br;
+	ino_t ino, dir_ino;
+	struct au_nfsd_si_lock nsi_lock = {
+		.force_lock	= 0
+	};
+
+	dentry = ERR_PTR(-ESTALE);
+	/* it should never happen, but the file handle is unreliable */
+	if (unlikely(fh_len < Fh_tail))
+		goto out;
+	nsi_lock.sigen = fh[Fh_sigen];
+	nsi_lock.br_id = fh[Fh_br_id];
+
+	/* branch id may be wrapped around */
+	br = NULL;
+	if (unlikely(si_nfsd_read_lock(sb, &nsi_lock)))
+		goto out;
+	nsi_lock.force_lock = 1;
+
+	/* is this inode still cached? */
+	ino = decode_ino(fh + Fh_ino);
+	/* it should never happen */
+	if (unlikely(ino == AUFS_ROOT_INO))
+		goto out_unlock;
+
+	dir_ino = decode_ino(fh + Fh_dir_ino);
+	dentry = decode_by_ino(sb, ino, dir_ino);
+	if (IS_ERR(dentry))
+		goto out_unlock;
+	if (dentry)
+		goto accept;
+
+	/* is the parent dir cached? */
+	br = au_sbr(sb, nsi_lock.bindex);
+	au_lcnt_inc(&br->br_nfiles);
+	dentry = decode_by_dir_ino(sb, ino, dir_ino, &nsi_lock);
+	if (IS_ERR(dentry))
+		goto out_unlock;
+	if (dentry)
+		goto accept;
+
+	/* lookup path */
+	dentry = decode_by_path(sb, ino, fh, fh_len, &nsi_lock);
+	if (IS_ERR(dentry))
+		goto out_unlock;
+	if (unlikely(!dentry))
+		/* todo?: make it ESTALE */
+		goto out_unlock;
+
+accept:
+	if (!au_digen_test(dentry, au_sigen(sb))
+	    && d_inode(dentry)->i_generation == fh[Fh_igen])
+		goto out_unlock; /* success */
+
+	dput(dentry);
+	dentry = ERR_PTR(-ESTALE);
+out_unlock:
+	if (br)
+		au_lcnt_dec(&br->br_nfiles);
+	si_read_unlock(sb);
+out:
+	AuTraceErrPtr(dentry);
+	return dentry;
+}
+
+#if 0 /* reserved for future use */
+/* support subtreecheck option */
+static struct dentry *aufs_fh_to_parent(struct super_block *sb, struct fid *fid,
+					int fh_len, int fh_type)
+{
+	struct dentry *parent;
+	__u32 *fh = fid->raw;
+	ino_t dir_ino;
+
+	dir_ino = decode_ino(fh + Fh_dir_ino);
+	parent = decode_by_ino(sb, dir_ino, 0);
+	if (IS_ERR(parent))
+		goto out;
+	if (!parent)
+		parent = decode_by_path(sb, au_br_index(sb, fh[Fh_br_id]),
+					dir_ino, fh, fh_len);
+
+out:
+	AuTraceErrPtr(parent);
+	return parent;
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+static int aufs_encode_fh(struct inode *inode, __u32 *fh, int *max_len,
+			  struct inode *dir)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct super_block *sb, *h_sb;
+	struct dentry *dentry, *parent, *h_parent;
+	struct inode *h_dir;
+	struct au_branch *br;
+
+	err = -ENOSPC;
+	if (unlikely(*max_len <= Fh_tail)) {
+		AuWarn1("NFSv2 client (max_len %d)?\n", *max_len);
+		goto out;
+	}
+
+	err = FILEID_ROOT;
+	if (inode->i_ino == AUFS_ROOT_INO) {
+		AuDebugOn(inode->i_ino != AUFS_ROOT_INO);
+		goto out;
+	}
+
+	h_parent = NULL;
+	sb = inode->i_sb;
+	err = si_read_lock(sb, AuLock_FLUSH);
+	if (unlikely(err))
+		goto out;
+
+#ifdef CONFIG_AUFS_DEBUG
+	if (unlikely(!au_opt_test(au_mntflags(sb), XINO)))
+		AuWarn1("NFS-exporting requires xino\n");
+#endif
+	err = -EIO;
+	parent = NULL;
+	ii_read_lock_child(inode);
+	bindex = au_ibtop(inode);
+	if (!dir) {
+		dentry = d_find_any_alias(inode);
+		if (unlikely(!dentry))
+			goto out_unlock;
+		AuDebugOn(au_test_anon(dentry));
+		parent = dget_parent(dentry);
+		dput(dentry);
+		if (unlikely(!parent))
+			goto out_unlock;
+		if (d_really_is_positive(parent))
+			dir = d_inode(parent);
+	}
+
+	ii_read_lock_parent(dir);
+	h_dir = au_h_iptr(dir, bindex);
+	ii_read_unlock(dir);
+	if (unlikely(!h_dir))
+		goto out_parent;
+	h_parent = d_find_any_alias(h_dir);
+	if (unlikely(!h_parent))
+		goto out_hparent;
+
+	err = -EPERM;
+	br = au_sbr(sb, bindex);
+	h_sb = au_br_sb(br);
+	if (unlikely(!h_sb->s_export_op)) {
+		AuErr1("%s branch is not exportable\n", au_sbtype(h_sb));
+		goto out_hparent;
+	}
+
+	fh[Fh_br_id] = br->br_id;
+	fh[Fh_sigen] = au_sigen(sb);
+	encode_ino(fh + Fh_ino, inode->i_ino);
+	encode_ino(fh + Fh_dir_ino, dir->i_ino);
+	fh[Fh_igen] = inode->i_generation;
+
+	*max_len -= Fh_tail;
+	fh[Fh_h_type] = exportfs_encode_fh(h_parent, (void *)(fh + Fh_tail),
+					   max_len,
+					   /*connectable or subtreecheck*/0);
+	err = fh[Fh_h_type];
+	*max_len += Fh_tail;
+	/* todo: macros? */
+	if (err != FILEID_INVALID)
+		err = 99;
+	else
+		AuWarn1("%s encode_fh failed\n", au_sbtype(h_sb));
+
+out_hparent:
+	dput(h_parent);
+out_parent:
+	dput(parent);
+out_unlock:
+	ii_read_unlock(inode);
+	si_read_unlock(sb);
+out:
+	if (unlikely(err < 0))
+		err = FILEID_INVALID;
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int aufs_commit_metadata(struct inode *inode)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct super_block *sb;
+	struct inode *h_inode;
+	int (*f)(struct inode *inode);
+
+	sb = inode->i_sb;
+	si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLMW);
+	ii_write_lock_child(inode);
+	bindex = au_ibtop(inode);
+	AuDebugOn(bindex < 0);
+	h_inode = au_h_iptr(inode, bindex);
+
+	f = h_inode->i_sb->s_export_op->commit_metadata;
+	if (f)
+		err = f(h_inode);
+	else
+		err = sync_inode_metadata(h_inode, /*wait*/1);
+
+	au_cpup_attr_timesizes(inode);
+	ii_write_unlock(inode);
+	si_read_unlock(sb);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct export_operations aufs_export_op = {
+	.fh_to_dentry		= aufs_fh_to_dentry,
+	/* .fh_to_parent	= aufs_fh_to_parent, */
+	.encode_fh		= aufs_encode_fh,
+	.commit_metadata	= aufs_commit_metadata
+};
+
+void au_export_init(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+	__u32 u;
+
+	BUILD_BUG_ON_MSG(IS_BUILTIN(CONFIG_AUFS_FS)
+			 && IS_MODULE(CONFIG_EXPORTFS),
+			 AUFS_NAME ": unsupported configuration "
+			 "CONFIG_EXPORTFS=m and CONFIG_AUFS_FS=y");
+
+	sb->s_export_op = &aufs_export_op;
+	sbinfo = au_sbi(sb);
+	sbinfo->si_xigen = NULL;
+	get_random_bytes(&u, sizeof(u));
+	BUILD_BUG_ON(sizeof(u) != sizeof(int));
+	atomic_set(&sbinfo->si_xigen_next, u);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/f_op.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/f_op.c
@@ -0,0 +1,771 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * file and vm operations
+ */
+
+#include <linux/aio.h>
+#include <linux/fs_stack.h>
+#include <linux/mman.h>
+#include <linux/security.h>
+#include "aufs.h"
+
+int au_do_open_nondir(struct file *file, int flags, struct file *h_file)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct dentry *dentry, *h_dentry;
+	struct au_finfo *finfo;
+	struct inode *h_inode;
+
+	FiMustWriteLock(file);
+
+	err = 0;
+	dentry = file->f_path.dentry;
+	AuDebugOn(IS_ERR_OR_NULL(dentry));
+	finfo = au_fi(file);
+	memset(&finfo->fi_htop, 0, sizeof(finfo->fi_htop));
+	atomic_set(&finfo->fi_mmapped, 0);
+	bindex = au_dbtop(dentry);
+	if (!h_file) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		err = vfsub_test_mntns(file->f_path.mnt, h_dentry->d_sb);
+		if (unlikely(err))
+			goto out;
+		h_file = au_h_open(dentry, bindex, flags, file, /*force_wr*/0);
+		if (IS_ERR(h_file)) {
+			err = PTR_ERR(h_file);
+			goto out;
+		}
+	} else {
+		h_dentry = h_file->f_path.dentry;
+		err = vfsub_test_mntns(file->f_path.mnt, h_dentry->d_sb);
+		if (unlikely(err))
+			goto out;
+		/* br ref is already inc-ed */
+	}
+
+	if ((flags & __O_TMPFILE)
+	    && !(flags & O_EXCL)) {
+		h_inode = file_inode(h_file);
+		spin_lock(&h_inode->i_lock);
+		h_inode->i_state |= I_LINKABLE;
+		spin_unlock(&h_inode->i_lock);
+	}
+	au_set_fbtop(file, bindex);
+	au_set_h_fptr(file, bindex, h_file);
+	au_update_figen(file);
+	/* todo: necessary? */
+	/* file->f_ra = h_file->f_ra; */
+
+out:
+	return err;
+}
+
+static int aufs_open_nondir(struct inode *inode __maybe_unused,
+			    struct file *file)
+{
+	int err;
+	struct super_block *sb;
+	struct au_do_open_args args = {
+		.open	= au_do_open_nondir
+	};
+
+	AuDbg("%pD, f_flags 0x%x, f_mode 0x%x\n",
+	      file, vfsub_file_flags(file), file->f_mode);
+
+	sb = file->f_path.dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH);
+	err = au_do_open(file, &args);
+	si_read_unlock(sb);
+	return err;
+}
+
+int aufs_release_nondir(struct inode *inode __maybe_unused, struct file *file)
+{
+	struct au_finfo *finfo;
+	aufs_bindex_t bindex;
+
+	finfo = au_fi(file);
+	au_hbl_del(&finfo->fi_hlist,
+		   &au_sbi(file->f_path.dentry->d_sb)->si_files);
+	bindex = finfo->fi_btop;
+	if (bindex >= 0)
+		au_set_h_fptr(file, bindex, NULL);
+
+	au_finfo_fin(file);
+	return 0;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_do_flush_nondir(struct file *file, fl_owner_t id)
+{
+	int err;
+	struct file *h_file;
+
+	err = 0;
+	h_file = au_hf_top(file);
+	if (h_file)
+		err = vfsub_flush(h_file, id);
+	return err;
+}
+
+static int aufs_flush_nondir(struct file *file, fl_owner_t id)
+{
+	return au_do_flush(file, id, au_do_flush_nondir);
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * read and write functions acquire [fdi]_rwsem once, but release before
+ * mmap_sem. This is because to stop a race condition between mmap(2).
+ * Releasing these aufs-rwsem should be safe, no branch-management (by keeping
+ * si_rwsem), no harmful copy-up should happen. Actually copy-up may happen in
+ * read functions after [fdi]_rwsem are released, but it should be harmless.
+ */
+
+/* Callers should call au_read_post() or fput() in the end */
+struct file *au_read_pre(struct file *file, int keep_fi, unsigned int lsc)
+{
+	struct file *h_file;
+	int err;
+
+	err = au_reval_and_lock_fdi(file, au_reopen_nondir, /*wlock*/0, lsc);
+	if (!err) {
+		di_read_unlock(file->f_path.dentry, AuLock_IR);
+		h_file = au_hf_top(file);
+		get_file(h_file);
+		if (!keep_fi)
+			fi_read_unlock(file);
+	} else
+		h_file = ERR_PTR(err);
+
+	return h_file;
+}
+
+static void au_read_post(struct inode *inode, struct file *h_file)
+{
+	/* update without lock, I don't think it a problem */
+	fsstack_copy_attr_atime(inode, file_inode(h_file));
+	fput(h_file);
+}
+
+struct au_write_pre {
+	/* input */
+	unsigned int lsc;
+
+	/* output */
+	blkcnt_t blks;
+	aufs_bindex_t btop;
+};
+
+/*
+ * return with iinfo is write-locked
+ * callers should call au_write_post() or iinfo_write_unlock() + fput() in the
+ * end
+ */
+static struct file *au_write_pre(struct file *file, int do_ready,
+				 struct au_write_pre *wpre)
+{
+	struct file *h_file;
+	struct dentry *dentry;
+	int err;
+	unsigned int lsc;
+	struct au_pin pin;
+
+	lsc = 0;
+	if (wpre)
+		lsc = wpre->lsc;
+	err = au_reval_and_lock_fdi(file, au_reopen_nondir, /*wlock*/1, lsc);
+	h_file = ERR_PTR(err);
+	if (unlikely(err))
+		goto out;
+
+	dentry = file->f_path.dentry;
+	if (do_ready) {
+		err = au_ready_to_write(file, -1, &pin);
+		if (unlikely(err)) {
+			h_file = ERR_PTR(err);
+			di_write_unlock(dentry);
+			goto out_fi;
+		}
+	}
+
+	di_downgrade_lock(dentry, /*flags*/0);
+	if (wpre)
+		wpre->btop = au_fbtop(file);
+	h_file = au_hf_top(file);
+	get_file(h_file);
+	if (wpre)
+		wpre->blks = file_inode(h_file)->i_blocks;
+	if (do_ready)
+		au_unpin(&pin);
+	di_read_unlock(dentry, /*flags*/0);
+
+out_fi:
+	fi_write_unlock(file);
+out:
+	return h_file;
+}
+
+static void au_write_post(struct inode *inode, struct file *h_file,
+			  struct au_write_pre *wpre, ssize_t written)
+{
+	struct inode *h_inode;
+
+	au_cpup_attr_timesizes(inode);
+	AuDebugOn(au_ibtop(inode) != wpre->btop);
+	h_inode = file_inode(h_file);
+	inode->i_mode = h_inode->i_mode;
+	ii_write_unlock(inode);
+	/* AuDbg("blks %llu, %llu\n", (u64)blks, (u64)h_inode->i_blocks); */
+	if (written > 0)
+		au_fhsm_wrote(inode->i_sb, wpre->btop,
+			      /*force*/h_inode->i_blocks > wpre->blks);
+	fput(h_file);
+}
+
+/*
+ * todo: very ugly
+ * it locks both of i_mutex and si_rwsem for read in safe.
+ * if the plink maintenance mode continues forever (that is the problem),
+ * may loop forever.
+ */
+static void au_mtx_and_read_lock(struct inode *inode)
+{
+	int err;
+	struct super_block *sb = inode->i_sb;
+
+	while (1) {
+		inode_lock(inode);
+		err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+		if (!err)
+			break;
+		inode_unlock(inode);
+		si_read_lock(sb, AuLock_NOPLMW);
+		si_read_unlock(sb);
+	}
+}
+
+static ssize_t au_do_iter(struct file *h_file, int rw, struct kiocb *kio,
+			  struct iov_iter *iov_iter)
+{
+	ssize_t err;
+	struct file *file;
+	ssize_t (*iter)(struct kiocb *, struct iov_iter *);
+
+	err = security_file_permission(h_file, rw);
+	if (unlikely(err))
+		goto out;
+
+	err = -ENOSYS;	/* the branch doesn't have its ->(read|write)_iter() */
+	iter = NULL;
+	if (rw == MAY_READ)
+		iter = h_file->f_op->read_iter;
+	else if (rw == MAY_WRITE)
+		iter = h_file->f_op->write_iter;
+
+	file = kio->ki_filp;
+	kio->ki_filp = h_file;
+	if (iter) {
+		lockdep_off();
+		err = iter(kio, iov_iter);
+		lockdep_on();
+	} else
+		/* currently there is no such fs */
+		WARN_ON_ONCE(1);
+	kio->ki_filp = file;
+
+out:
+	return err;
+}
+
+static ssize_t aufs_read_iter(struct kiocb *kio, struct iov_iter *iov_iter)
+{
+	ssize_t err;
+	struct file *file, *h_file;
+	struct inode *inode;
+	struct super_block *sb;
+
+	file = kio->ki_filp;
+	inode = file_inode(file);
+	sb = inode->i_sb;
+	si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLMW);
+
+	h_file = au_read_pre(file, /*keep_fi*/1, /*lsc*/0);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	if (0 && au_test_loopback_kthread()) {
+		au_warn_loopback(h_file->f_path.dentry->d_sb);
+		if (file->f_mapping != h_file->f_mapping) {
+			file->f_mapping = h_file->f_mapping;
+			smp_mb(); /* unnecessary? */
+		}
+	}
+	fi_read_unlock(file);
+
+	err = au_do_iter(h_file, MAY_READ, kio, iov_iter);
+	/* todo: necessary? */
+	/* file->f_ra = h_file->f_ra; */
+	au_read_post(inode, h_file);
+
+out:
+	si_read_unlock(sb);
+	return err;
+}
+
+static ssize_t aufs_write_iter(struct kiocb *kio, struct iov_iter *iov_iter)
+{
+	ssize_t err;
+	struct au_write_pre wpre;
+	struct inode *inode;
+	struct file *file, *h_file;
+
+	file = kio->ki_filp;
+	inode = file_inode(file);
+	au_mtx_and_read_lock(inode);
+
+	wpre.lsc = 0;
+	h_file = au_write_pre(file, /*do_ready*/1, &wpre);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	err = au_do_iter(h_file, MAY_WRITE, kio, iov_iter);
+	au_write_post(inode, h_file, &wpre, err);
+
+out:
+	si_read_unlock(inode->i_sb);
+	inode_unlock(inode);
+	return err;
+}
+
+/*
+ * We may be able to remove aufs_splice_{read,write}() since almost all FSes
+ * don't have their own .splice_{read,write} implimentations, and they use
+ * generic_file_splice_read() and iter_file_splice_write() who can act like the
+ * simple converters to f_op->iter_read() and ->iter_write().
+ * But we keep our own implementations because some non-mainlined FSes may have
+ * their own .splice_{read,write} implimentations and aufs doesn't want to take
+ * away an opportunity to co-work with aufs from them.
+ */
+static ssize_t aufs_splice_read(struct file *file, loff_t *ppos,
+				struct pipe_inode_info *pipe, size_t len,
+				unsigned int flags)
+{
+	ssize_t err;
+	struct file *h_file;
+	struct inode *inode;
+	struct super_block *sb;
+
+	inode = file_inode(file);
+	sb = inode->i_sb;
+	si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLMW);
+
+	h_file = au_read_pre(file, /*keep_fi*/0, /*lsc*/0);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	err = vfsub_splice_to(h_file, ppos, pipe, len, flags);
+	/* todo: necessary? */
+	/* file->f_ra = h_file->f_ra; */
+	au_read_post(inode, h_file);
+
+out:
+	si_read_unlock(sb);
+	return err;
+}
+
+static ssize_t
+aufs_splice_write(struct pipe_inode_info *pipe, struct file *file, loff_t *ppos,
+		  size_t len, unsigned int flags)
+{
+	ssize_t err;
+	struct au_write_pre wpre;
+	struct inode *inode;
+	struct file *h_file;
+
+	inode = file_inode(file);
+	au_mtx_and_read_lock(inode);
+
+	wpre.lsc = 0;
+	h_file = au_write_pre(file, /*do_ready*/1, &wpre);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	err = vfsub_splice_from(pipe, h_file, ppos, len, flags);
+	au_write_post(inode, h_file, &wpre, err);
+
+out:
+	si_read_unlock(inode->i_sb);
+	inode_unlock(inode);
+	return err;
+}
+
+static long aufs_fallocate(struct file *file, int mode, loff_t offset,
+			   loff_t len)
+{
+	long err;
+	struct au_write_pre wpre;
+	struct inode *inode;
+	struct file *h_file;
+
+	inode = file_inode(file);
+	au_mtx_and_read_lock(inode);
+
+	wpre.lsc = 0;
+	h_file = au_write_pre(file, /*do_ready*/1, &wpre);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	lockdep_off();
+	err = vfs_fallocate(h_file, mode, offset, len);
+	lockdep_on();
+	au_write_post(inode, h_file, &wpre, /*written*/1);
+
+out:
+	si_read_unlock(inode->i_sb);
+	inode_unlock(inode);
+	return err;
+}
+
+static ssize_t aufs_copy_file_range(struct file *src, loff_t src_pos,
+				    struct file *dst, loff_t dst_pos,
+				    size_t len, unsigned int flags)
+{
+	ssize_t err;
+	struct au_write_pre wpre;
+	enum { SRC, DST };
+	struct {
+		struct inode *inode;
+		struct file *h_file;
+		struct super_block *h_sb;
+	} a[2];
+#define a_src	a[SRC]
+#define a_dst	a[DST]
+
+	err = -EINVAL;
+	a_src.inode = file_inode(src);
+	if (unlikely(!S_ISREG(a_src.inode->i_mode)))
+		goto out;
+	a_dst.inode = file_inode(dst);
+	if (unlikely(!S_ISREG(a_dst.inode->i_mode)))
+		goto out;
+
+	au_mtx_and_read_lock(a_dst.inode);
+	/*
+	 * in order to match the order in di_write_lock2_{child,parent}(),
+	 * use f_path.dentry for this comparison.
+	 */
+	if (src->f_path.dentry < dst->f_path.dentry) {
+		a_src.h_file = au_read_pre(src, /*keep_fi*/1, AuLsc_FI_1);
+		err = PTR_ERR(a_src.h_file);
+		if (IS_ERR(a_src.h_file))
+			goto out_si;
+
+		wpre.lsc = AuLsc_FI_2;
+		a_dst.h_file = au_write_pre(dst, /*do_ready*/1, &wpre);
+		err = PTR_ERR(a_dst.h_file);
+		if (IS_ERR(a_dst.h_file)) {
+			au_read_post(a_src.inode, a_src.h_file);
+			goto out_si;
+		}
+	} else {
+		wpre.lsc = AuLsc_FI_1;
+		a_dst.h_file = au_write_pre(dst, /*do_ready*/1, &wpre);
+		err = PTR_ERR(a_dst.h_file);
+		if (IS_ERR(a_dst.h_file))
+			goto out_si;
+
+		a_src.h_file = au_read_pre(src, /*keep_fi*/1, AuLsc_FI_2);
+		err = PTR_ERR(a_src.h_file);
+		if (IS_ERR(a_src.h_file)) {
+			au_write_post(a_dst.inode, a_dst.h_file, &wpre,
+				      /*written*/0);
+			goto out_si;
+		}
+	}
+
+	err = -EXDEV;
+	a_src.h_sb = file_inode(a_src.h_file)->i_sb;
+	a_dst.h_sb = file_inode(a_dst.h_file)->i_sb;
+	if (unlikely(a_src.h_sb != a_dst.h_sb)) {
+		AuDbgFile(src);
+		AuDbgFile(dst);
+		goto out_file;
+	}
+
+	err = vfsub_copy_file_range(a_src.h_file, src_pos, a_dst.h_file,
+				    dst_pos, len, flags);
+
+out_file:
+	au_write_post(a_dst.inode, a_dst.h_file, &wpre, err);
+	fi_read_unlock(src);
+	au_read_post(a_src.inode, a_src.h_file);
+out_si:
+	si_read_unlock(a_dst.inode->i_sb);
+	inode_unlock(a_dst.inode);
+out:
+	return err;
+#undef a_src
+#undef a_dst
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * The locking order around current->mmap_sem.
+ * - in most and regular cases
+ *   file I/O syscall -- aufs_read() or something
+ *	-- si_rwsem for read -- mmap_sem
+ *	(Note that [fdi]i_rwsem are released before mmap_sem).
+ * - in mmap case
+ *   mmap(2) -- mmap_sem -- aufs_mmap() -- si_rwsem for read -- [fdi]i_rwsem
+ * This AB-BA order is definitely bad, but is not a problem since "si_rwsem for
+ * read" allows multiple processes to acquire it and [fdi]i_rwsem are not held
+ * in file I/O. Aufs needs to stop lockdep in aufs_mmap() though.
+ * It means that when aufs acquires si_rwsem for write, the process should never
+ * acquire mmap_sem.
+ *
+ * Actually aufs_iterate() holds [fdi]i_rwsem before mmap_sem, but this is not a
+ * problem either since any directory is not able to be mmap-ed.
+ * The similar scenario is applied to aufs_readlink() too.
+ */
+
+#if 0 /* stop calling security_file_mmap() */
+/* cf. linux/include/linux/mman.h: calc_vm_prot_bits() */
+#define AuConv_VM_PROT(f, b)	_calc_vm_trans(f, VM_##b, PROT_##b)
+
+static unsigned long au_arch_prot_conv(unsigned long flags)
+{
+	/* currently ppc64 only */
+#ifdef CONFIG_PPC64
+	/* cf. linux/arch/powerpc/include/asm/mman.h */
+	AuDebugOn(arch_calc_vm_prot_bits(-1) != VM_SAO);
+	return AuConv_VM_PROT(flags, SAO);
+#else
+	AuDebugOn(arch_calc_vm_prot_bits(-1));
+	return 0;
+#endif
+}
+
+static unsigned long au_prot_conv(unsigned long flags)
+{
+	return AuConv_VM_PROT(flags, READ)
+		| AuConv_VM_PROT(flags, WRITE)
+		| AuConv_VM_PROT(flags, EXEC)
+		| au_arch_prot_conv(flags);
+}
+
+/* cf. linux/include/linux/mman.h: calc_vm_flag_bits() */
+#define AuConv_VM_MAP(f, b)	_calc_vm_trans(f, VM_##b, MAP_##b)
+
+static unsigned long au_flag_conv(unsigned long flags)
+{
+	return AuConv_VM_MAP(flags, GROWSDOWN)
+		| AuConv_VM_MAP(flags, DENYWRITE)
+		| AuConv_VM_MAP(flags, LOCKED);
+}
+#endif
+
+static int aufs_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	int err;
+	const unsigned char wlock
+		= (file->f_mode & FMODE_WRITE) && (vma->vm_flags & VM_SHARED);
+	struct super_block *sb;
+	struct file *h_file;
+	struct inode *inode;
+
+	AuDbgVmRegion(file, vma);
+
+	inode = file_inode(file);
+	sb = inode->i_sb;
+	lockdep_off();
+	si_read_lock(sb, AuLock_NOPLMW);
+
+	h_file = au_write_pre(file, wlock, /*wpre*/NULL);
+	lockdep_on();
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	err = 0;
+	au_set_mmapped(file);
+	au_vm_file_reset(vma, h_file);
+	/*
+	 * we cannot call security_mmap_file() here since it may acquire
+	 * mmap_sem or i_mutex.
+	 *
+	 * err = security_mmap_file(h_file, au_prot_conv(vma->vm_flags),
+	 *			 au_flag_conv(vma->vm_flags));
+	 */
+	if (!err)
+		err = call_mmap(h_file, vma);
+	if (!err) {
+		au_vm_prfile_set(vma, file);
+		fsstack_copy_attr_atime(inode, file_inode(h_file));
+		goto out_fput; /* success */
+	}
+	au_unset_mmapped(file);
+	au_vm_file_reset(vma, file);
+
+out_fput:
+	lockdep_off();
+	ii_write_unlock(inode);
+	lockdep_on();
+	fput(h_file);
+out:
+	lockdep_off();
+	si_read_unlock(sb);
+	lockdep_on();
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int aufs_fsync_nondir(struct file *file, loff_t start, loff_t end,
+			     int datasync)
+{
+	int err;
+	struct au_write_pre wpre;
+	struct inode *inode;
+	struct file *h_file;
+
+	err = 0; /* -EBADF; */ /* posix? */
+	if (unlikely(!(file->f_mode & FMODE_WRITE)))
+		goto out;
+
+	inode = file_inode(file);
+	au_mtx_and_read_lock(inode);
+
+	wpre.lsc = 0;
+	h_file = au_write_pre(file, /*do_ready*/1, &wpre);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out_unlock;
+
+	err = vfsub_fsync(h_file, &h_file->f_path, datasync);
+	au_write_post(inode, h_file, &wpre, /*written*/0);
+
+out_unlock:
+	si_read_unlock(inode->i_sb);
+	inode_unlock(inode);
+out:
+	return err;
+}
+
+static int aufs_fasync(int fd, struct file *file, int flag)
+{
+	int err;
+	struct file *h_file;
+	struct super_block *sb;
+
+	sb = file->f_path.dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLMW);
+
+	h_file = au_read_pre(file, /*keep_fi*/0, /*lsc*/0);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	if (h_file->f_op->fasync)
+		err = h_file->f_op->fasync(fd, h_file, flag);
+	fput(h_file); /* instead of au_read_post() */
+
+out:
+	si_read_unlock(sb);
+	return err;
+}
+
+static int aufs_setfl(struct file *file, unsigned long arg)
+{
+	int err;
+	struct file *h_file;
+	struct super_block *sb;
+
+	sb = file->f_path.dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLMW);
+
+	h_file = au_read_pre(file, /*keep_fi*/0, /*lsc*/0);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out;
+
+	/* stop calling h_file->fasync */
+	arg |= vfsub_file_flags(file) & FASYNC;
+	err = setfl(/*unused fd*/-1, h_file, arg);
+	fput(h_file); /* instead of au_read_post() */
+
+out:
+	si_read_unlock(sb);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* no one supports this operation, currently */
+#if 0 /* reserved for future use */
+static ssize_t aufs_sendpage(struct file *file, struct page *page, int offset,
+			     size_t len, loff_t *pos, int more)
+{
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+const struct file_operations aufs_file_fop = {
+	.owner		= THIS_MODULE,
+
+	.llseek		= default_llseek,
+
+	.read_iter	= aufs_read_iter,
+	.write_iter	= aufs_write_iter,
+
+#ifdef CONFIG_AUFS_POLL
+	.poll		= aufs_poll,
+#endif
+	.unlocked_ioctl	= aufs_ioctl_nondir,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl	= aufs_compat_ioctl_nondir,
+#endif
+	.mmap		= aufs_mmap,
+	.open		= aufs_open_nondir,
+	.flush		= aufs_flush_nondir,
+	.release	= aufs_release_nondir,
+	.fsync		= aufs_fsync_nondir,
+	.fasync		= aufs_fasync,
+	/* .sendpage	= aufs_sendpage, */
+	.setfl		= aufs_setfl,
+	.splice_write	= aufs_splice_write,
+	.splice_read	= aufs_splice_read,
+#if 0 /* reserved for future use */
+	.aio_splice_write = aufs_aio_splice_write,
+	.aio_splice_read  = aufs_aio_splice_read,
+#endif
+	.fallocate	= aufs_fallocate,
+	.copy_file_range = aufs_copy_file_range
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/fhsm.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/fhsm.c
@@ -0,0 +1,427 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2011-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+/*
+ * File-based Hierarchy Storage Management
+ */
+
+#include <linux/anon_inodes.h>
+#include <linux/poll.h>
+#include <linux/seq_file.h>
+#include <linux/statfs.h>
+#include "aufs.h"
+
+static aufs_bindex_t au_fhsm_bottom(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+
+	SiMustAnyLock(sb);
+
+	sbinfo = au_sbi(sb);
+	fhsm = &sbinfo->si_fhsm;
+	AuDebugOn(!fhsm);
+	return fhsm->fhsm_bottom;
+}
+
+void au_fhsm_set_bottom(struct super_block *sb, aufs_bindex_t bindex)
+{
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	fhsm = &sbinfo->si_fhsm;
+	AuDebugOn(!fhsm);
+	fhsm->fhsm_bottom = bindex;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_fhsm_test_jiffy(struct au_sbinfo *sbinfo, struct au_branch *br)
+{
+	struct au_br_fhsm *bf;
+
+	bf = br->br_fhsm;
+	MtxMustLock(&bf->bf_lock);
+
+	return !bf->bf_readable
+		|| time_after(jiffies,
+			      bf->bf_jiffy + sbinfo->si_fhsm.fhsm_expire);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void au_fhsm_notify(struct super_block *sb, int val)
+{
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+
+	SiMustAnyLock(sb);
+
+	sbinfo = au_sbi(sb);
+	fhsm = &sbinfo->si_fhsm;
+	if (au_fhsm_pid(fhsm)
+	    && atomic_read(&fhsm->fhsm_readable) != -1) {
+		atomic_set(&fhsm->fhsm_readable, val);
+		if (val)
+			wake_up(&fhsm->fhsm_wqh);
+	}
+}
+
+static int au_fhsm_stfs(struct super_block *sb, aufs_bindex_t bindex,
+			struct aufs_stfs *rstfs, int do_lock, int do_notify)
+{
+	int err;
+	struct au_branch *br;
+	struct au_br_fhsm *bf;
+
+	br = au_sbr(sb, bindex);
+	AuDebugOn(au_br_rdonly(br));
+	bf = br->br_fhsm;
+	AuDebugOn(!bf);
+
+	if (do_lock)
+		mutex_lock(&bf->bf_lock);
+	else
+		MtxMustLock(&bf->bf_lock);
+
+	/* sb->s_root for NFS is unreliable */
+	err = au_br_stfs(br, &bf->bf_stfs);
+	if (unlikely(err)) {
+		AuErr1("FHSM failed (%d), b%d, ignored.\n", bindex, err);
+		goto out;
+	}
+
+	bf->bf_jiffy = jiffies;
+	bf->bf_readable = 1;
+	if (do_notify)
+		au_fhsm_notify(sb, /*val*/1);
+	if (rstfs)
+		*rstfs = bf->bf_stfs;
+
+out:
+	if (do_lock)
+		mutex_unlock(&bf->bf_lock);
+	au_fhsm_notify(sb, /*val*/1);
+
+	return err;
+}
+
+void au_fhsm_wrote(struct super_block *sb, aufs_bindex_t bindex, int force)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+	struct au_branch *br;
+	struct au_br_fhsm *bf;
+
+	AuDbg("b%d, force %d\n", bindex, force);
+	SiMustAnyLock(sb);
+
+	sbinfo = au_sbi(sb);
+	fhsm = &sbinfo->si_fhsm;
+	if (!au_ftest_si(sbinfo, FHSM)
+	    || fhsm->fhsm_bottom == bindex)
+		return;
+
+	br = au_sbr(sb, bindex);
+	bf = br->br_fhsm;
+	AuDebugOn(!bf);
+	mutex_lock(&bf->bf_lock);
+	if (force
+	    || au_fhsm_pid(fhsm)
+	    || au_fhsm_test_jiffy(sbinfo, br))
+		err = au_fhsm_stfs(sb, bindex, /*rstfs*/NULL, /*do_lock*/0,
+				  /*do_notify*/1);
+	mutex_unlock(&bf->bf_lock);
+}
+
+void au_fhsm_wrote_all(struct super_block *sb, int force)
+{
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+
+	/* exclude the bottom */
+	bbot = au_fhsm_bottom(sb);
+	for (bindex = 0; bindex < bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (au_br_fhsm(br->br_perm))
+			au_fhsm_wrote(sb, bindex, force);
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+static __poll_t au_fhsm_poll(struct file *file, struct poll_table_struct *wait)
+{
+	__poll_t mask;
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+
+	mask = 0;
+	sbinfo = file->private_data;
+	fhsm = &sbinfo->si_fhsm;
+	poll_wait(file, &fhsm->fhsm_wqh, wait);
+	if (atomic_read(&fhsm->fhsm_readable))
+		mask = EPOLLIN /* | EPOLLRDNORM */;
+
+	if (!mask)
+		AuDbg("mask 0x%x\n", mask);
+	return mask;
+}
+
+static int au_fhsm_do_read_one(struct aufs_stbr __user *stbr,
+			      struct aufs_stfs *stfs, __s16 brid)
+{
+	int err;
+
+	err = copy_to_user(&stbr->stfs, stfs, sizeof(*stfs));
+	if (!err)
+		err = __put_user(brid, &stbr->brid);
+	if (unlikely(err))
+		err = -EFAULT;
+
+	return err;
+}
+
+static ssize_t au_fhsm_do_read(struct super_block *sb,
+			       struct aufs_stbr __user *stbr, size_t count)
+{
+	ssize_t err;
+	int nstbr;
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+	struct au_br_fhsm *bf;
+
+	/* except the bottom branch */
+	err = 0;
+	nstbr = 0;
+	bbot = au_fhsm_bottom(sb);
+	for (bindex = 0; !err && bindex < bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (!au_br_fhsm(br->br_perm))
+			continue;
+
+		bf = br->br_fhsm;
+		mutex_lock(&bf->bf_lock);
+		if (bf->bf_readable) {
+			err = -EFAULT;
+			if (count >= sizeof(*stbr))
+				err = au_fhsm_do_read_one(stbr++, &bf->bf_stfs,
+							  br->br_id);
+			if (!err) {
+				bf->bf_readable = 0;
+				count -= sizeof(*stbr);
+				nstbr++;
+			}
+		}
+		mutex_unlock(&bf->bf_lock);
+	}
+	if (!err)
+		err = sizeof(*stbr) * nstbr;
+
+	return err;
+}
+
+static ssize_t au_fhsm_read(struct file *file, char __user *buf, size_t count,
+			   loff_t *pos)
+{
+	ssize_t err;
+	int readable;
+	aufs_bindex_t nfhsm, bindex, bbot;
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+	struct au_branch *br;
+	struct super_block *sb;
+
+	err = 0;
+	sbinfo = file->private_data;
+	fhsm = &sbinfo->si_fhsm;
+need_data:
+	spin_lock_irq(&fhsm->fhsm_wqh.lock);
+	if (!atomic_read(&fhsm->fhsm_readable)) {
+		if (vfsub_file_flags(file) & O_NONBLOCK)
+			err = -EAGAIN;
+		else
+			err = wait_event_interruptible_locked_irq
+				(fhsm->fhsm_wqh,
+				 atomic_read(&fhsm->fhsm_readable));
+	}
+	spin_unlock_irq(&fhsm->fhsm_wqh.lock);
+	if (unlikely(err))
+		goto out;
+
+	/* sb may already be dead */
+	au_rw_read_lock(&sbinfo->si_rwsem);
+	readable = atomic_read(&fhsm->fhsm_readable);
+	if (readable > 0) {
+		sb = sbinfo->si_sb;
+		AuDebugOn(!sb);
+		/* exclude the bottom branch */
+		nfhsm = 0;
+		bbot = au_fhsm_bottom(sb);
+		for (bindex = 0; bindex < bbot; bindex++) {
+			br = au_sbr(sb, bindex);
+			if (au_br_fhsm(br->br_perm))
+				nfhsm++;
+		}
+		err = -EMSGSIZE;
+		if (nfhsm * sizeof(struct aufs_stbr) <= count) {
+			atomic_set(&fhsm->fhsm_readable, 0);
+			err = au_fhsm_do_read(sbinfo->si_sb, (void __user *)buf,
+					     count);
+		}
+	}
+	au_rw_read_unlock(&sbinfo->si_rwsem);
+	if (!readable)
+		goto need_data;
+
+out:
+	return err;
+}
+
+static int au_fhsm_release(struct inode *inode, struct file *file)
+{
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+
+	/* sb may already be dead */
+	sbinfo = file->private_data;
+	fhsm = &sbinfo->si_fhsm;
+	spin_lock(&fhsm->fhsm_spin);
+	fhsm->fhsm_pid = 0;
+	spin_unlock(&fhsm->fhsm_spin);
+	kobject_put(&sbinfo->si_kobj);
+
+	return 0;
+}
+
+static const struct file_operations au_fhsm_fops = {
+	.owner		= THIS_MODULE,
+	.llseek		= noop_llseek,
+	.read		= au_fhsm_read,
+	.poll		= au_fhsm_poll,
+	.release	= au_fhsm_release
+};
+
+int au_fhsm_fd(struct super_block *sb, int oflags)
+{
+	int err, fd;
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+
+	err = -EPERM;
+	if (unlikely(!capable(CAP_SYS_ADMIN)))
+		goto out;
+
+	err = -EINVAL;
+	if (unlikely(oflags & ~(O_CLOEXEC | O_NONBLOCK)))
+		goto out;
+
+	err = 0;
+	sbinfo = au_sbi(sb);
+	fhsm = &sbinfo->si_fhsm;
+	spin_lock(&fhsm->fhsm_spin);
+	if (!fhsm->fhsm_pid)
+		fhsm->fhsm_pid = current->pid;
+	else
+		err = -EBUSY;
+	spin_unlock(&fhsm->fhsm_spin);
+	if (unlikely(err))
+		goto out;
+
+	oflags |= O_RDONLY;
+	/* oflags |= FMODE_NONOTIFY; */
+	fd = anon_inode_getfd("[aufs_fhsm]", &au_fhsm_fops, sbinfo, oflags);
+	err = fd;
+	if (unlikely(fd < 0))
+		goto out_pid;
+
+	/* succeed regardless 'fhsm' status */
+	kobject_get(&sbinfo->si_kobj);
+	si_noflush_read_lock(sb);
+	if (au_ftest_si(sbinfo, FHSM))
+		au_fhsm_wrote_all(sb, /*force*/0);
+	si_read_unlock(sb);
+	goto out; /* success */
+
+out_pid:
+	spin_lock(&fhsm->fhsm_spin);
+	fhsm->fhsm_pid = 0;
+	spin_unlock(&fhsm->fhsm_spin);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_fhsm_br_alloc(struct au_branch *br)
+{
+	int err;
+
+	err = 0;
+	br->br_fhsm = kmalloc(sizeof(*br->br_fhsm), GFP_NOFS);
+	if (br->br_fhsm)
+		au_br_fhsm_init(br->br_fhsm);
+	else
+		err = -ENOMEM;
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_fhsm_fin(struct super_block *sb)
+{
+	au_fhsm_notify(sb, /*val*/-1);
+}
+
+void au_fhsm_init(struct au_sbinfo *sbinfo)
+{
+	struct au_fhsm *fhsm;
+
+	fhsm = &sbinfo->si_fhsm;
+	spin_lock_init(&fhsm->fhsm_spin);
+	init_waitqueue_head(&fhsm->fhsm_wqh);
+	atomic_set(&fhsm->fhsm_readable, 0);
+	fhsm->fhsm_expire
+		= msecs_to_jiffies(AUFS_FHSM_CACHE_DEF_SEC * MSEC_PER_SEC);
+	fhsm->fhsm_bottom = -1;
+}
+
+void au_fhsm_set(struct au_sbinfo *sbinfo, unsigned int sec)
+{
+	sbinfo->si_fhsm.fhsm_expire
+		= msecs_to_jiffies(sec * MSEC_PER_SEC);
+}
+
+void au_fhsm_show(struct seq_file *seq, struct au_sbinfo *sbinfo)
+{
+	unsigned int u;
+
+	if (!au_ftest_si(sbinfo, FHSM))
+		return;
+
+	u = jiffies_to_msecs(sbinfo->si_fhsm.fhsm_expire) / MSEC_PER_SEC;
+	if (u != AUFS_FHSM_CACHE_DEF_SEC)
+		seq_printf(seq, ",fhsm_sec=%u", u);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/file.c
@@ -0,0 +1,863 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * handling file/dir, and address_space operation
+ */
+
+#ifdef CONFIG_AUFS_DEBUG
+#include <linux/migrate.h>
+#endif
+#include <linux/pagemap.h>
+#include "aufs.h"
+
+/* drop flags for writing */
+unsigned int au_file_roflags(unsigned int flags)
+{
+	flags &= ~(O_WRONLY | O_RDWR | O_APPEND | O_CREAT | O_TRUNC);
+	flags |= O_RDONLY | O_NOATIME;
+	return flags;
+}
+
+/* common functions to regular file and dir */
+struct file *au_h_open(struct dentry *dentry, aufs_bindex_t bindex, int flags,
+		       struct file *file, int force_wr)
+{
+	struct file *h_file;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct path h_path;
+	int err;
+
+	/* a race condition can happen between open and unlink/rmdir */
+	h_file = ERR_PTR(-ENOENT);
+	h_dentry = au_h_dptr(dentry, bindex);
+	if (au_test_nfsd() && (!h_dentry || d_is_negative(h_dentry)))
+		goto out;
+	h_inode = d_inode(h_dentry);
+	spin_lock(&h_dentry->d_lock);
+	err = (!d_unhashed(dentry) && d_unlinked(h_dentry))
+		/* || !d_inode(dentry)->i_nlink */
+		;
+	spin_unlock(&h_dentry->d_lock);
+	if (unlikely(err))
+		goto out;
+
+	sb = dentry->d_sb;
+	br = au_sbr(sb, bindex);
+	err = au_br_test_oflag(flags, br);
+	h_file = ERR_PTR(err);
+	if (unlikely(err))
+		goto out;
+
+	/* drop flags for writing */
+	if (au_test_ro(sb, bindex, d_inode(dentry))) {
+		if (force_wr && !(flags & O_WRONLY))
+			force_wr = 0;
+		flags = au_file_roflags(flags);
+		if (force_wr) {
+			h_file = ERR_PTR(-EROFS);
+			flags = au_file_roflags(flags);
+			if (unlikely(vfsub_native_ro(h_inode)
+				     || IS_APPEND(h_inode)))
+				goto out;
+			flags &= ~O_ACCMODE;
+			flags |= O_WRONLY;
+		}
+	}
+	flags &= ~O_CREAT;
+	au_lcnt_inc(&br->br_nfiles);
+	h_path.dentry = h_dentry;
+	h_path.mnt = au_br_mnt(br);
+	h_file = vfsub_dentry_open(&h_path, flags);
+	if (IS_ERR(h_file))
+		goto out_br;
+
+	if (flags & __FMODE_EXEC) {
+		err = deny_write_access(h_file);
+		if (unlikely(err)) {
+			fput(h_file);
+			h_file = ERR_PTR(err);
+			goto out_br;
+		}
+	}
+	fsnotify_open(h_file);
+	goto out; /* success */
+
+out_br:
+	au_lcnt_dec(&br->br_nfiles);
+out:
+	return h_file;
+}
+
+static int au_cmoo(struct dentry *dentry)
+{
+	int err, cmoo, matched;
+	unsigned int udba;
+	struct path h_path;
+	struct au_pin pin;
+	struct au_cp_generic cpg = {
+		.dentry	= dentry,
+		.bdst	= -1,
+		.bsrc	= -1,
+		.len	= -1,
+		.pin	= &pin,
+		.flags	= AuCpup_DTIME | AuCpup_HOPEN
+	};
+	struct inode *delegated;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+	struct au_fhsm *fhsm;
+	pid_t pid;
+	struct au_branch *br;
+	struct dentry *parent;
+	struct au_hinode *hdir;
+
+	DiMustWriteLock(dentry);
+	IiMustWriteLock(d_inode(dentry));
+
+	err = 0;
+	if (IS_ROOT(dentry))
+		goto out;
+	cpg.bsrc = au_dbtop(dentry);
+	if (!cpg.bsrc)
+		goto out;
+
+	sb = dentry->d_sb;
+	sbinfo = au_sbi(sb);
+	fhsm = &sbinfo->si_fhsm;
+	pid = au_fhsm_pid(fhsm);
+	rcu_read_lock();
+	matched = (pid
+		   && (current->pid == pid
+		       || rcu_dereference(current->real_parent)->pid == pid));
+	rcu_read_unlock();
+	if (matched)
+		goto out;
+
+	br = au_sbr(sb, cpg.bsrc);
+	cmoo = au_br_cmoo(br->br_perm);
+	if (!cmoo)
+		goto out;
+	if (!d_is_reg(dentry))
+		cmoo &= AuBrAttr_COO_ALL;
+	if (!cmoo)
+		goto out;
+
+	parent = dget_parent(dentry);
+	di_write_lock_parent(parent);
+	err = au_wbr_do_copyup_bu(dentry, cpg.bsrc - 1);
+	cpg.bdst = err;
+	if (unlikely(err < 0)) {
+		err = 0;	/* there is no upper writable branch */
+		goto out_dgrade;
+	}
+	AuDbg("bsrc %d, bdst %d\n", cpg.bsrc, cpg.bdst);
+
+	/* do not respect the coo attrib for the target branch */
+	err = au_cpup_dirs(dentry, cpg.bdst);
+	if (unlikely(err))
+		goto out_dgrade;
+
+	di_downgrade_lock(parent, AuLock_IR);
+	udba = au_opt_udba(sb);
+	err = au_pin(&pin, dentry, cpg.bdst, udba,
+		     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+	if (unlikely(err))
+		goto out_parent;
+
+	err = au_sio_cpup_simple(&cpg);
+	au_unpin(&pin);
+	if (unlikely(err))
+		goto out_parent;
+	if (!(cmoo & AuBrWAttr_MOO))
+		goto out_parent; /* success */
+
+	err = au_pin(&pin, dentry, cpg.bsrc, udba,
+		     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+	if (unlikely(err))
+		goto out_parent;
+
+	h_path.mnt = au_br_mnt(br);
+	h_path.dentry = au_h_dptr(dentry, cpg.bsrc);
+	hdir = au_hi(d_inode(parent), cpg.bsrc);
+	delegated = NULL;
+	err = vfsub_unlink(hdir->hi_inode, &h_path, &delegated, /*force*/1);
+	au_unpin(&pin);
+	/* todo: keep h_dentry or not? */
+	if (unlikely(err == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal unlink\n");
+		iput(delegated);
+	}
+	if (unlikely(err)) {
+		pr_err("unlink %pd after coo failed (%d), ignored\n",
+		       dentry, err);
+		err = 0;
+	}
+	goto out_parent; /* success */
+
+out_dgrade:
+	di_downgrade_lock(parent, AuLock_IR);
+out_parent:
+	di_read_unlock(parent, AuLock_IR);
+	dput(parent);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_do_open(struct file *file, struct au_do_open_args *args)
+{
+	int err, aopen = args->aopen;
+	struct dentry *dentry;
+	struct au_finfo *finfo;
+
+	if (!aopen)
+		err = au_finfo_init(file, args->fidir);
+	else {
+		lockdep_off();
+		err = au_finfo_init(file, args->fidir);
+		lockdep_on();
+	}
+	if (unlikely(err))
+		goto out;
+
+	dentry = file->f_path.dentry;
+	AuDebugOn(IS_ERR_OR_NULL(dentry));
+	di_write_lock_child(dentry);
+	err = au_cmoo(dentry);
+	di_downgrade_lock(dentry, AuLock_IR);
+	if (!err) {
+		if (!aopen)
+			err = args->open(file, vfsub_file_flags(file), NULL);
+		else {
+			lockdep_off();
+			err = args->open(file, vfsub_file_flags(file),
+					 args->h_file);
+			lockdep_on();
+		}
+	}
+	di_read_unlock(dentry, AuLock_IR);
+
+	finfo = au_fi(file);
+	if (!err) {
+		finfo->fi_file = file;
+		au_hbl_add(&finfo->fi_hlist,
+			   &au_sbi(file->f_path.dentry->d_sb)->si_files);
+	}
+	if (!aopen)
+		fi_write_unlock(file);
+	else {
+		lockdep_off();
+		fi_write_unlock(file);
+		lockdep_on();
+	}
+	if (unlikely(err)) {
+		finfo->fi_hdir = NULL;
+		au_finfo_fin(file);
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_reopen_nondir(struct file *file)
+{
+	int err;
+	aufs_bindex_t btop;
+	struct dentry *dentry;
+	struct au_branch *br;
+	struct file *h_file, *h_file_tmp;
+
+	dentry = file->f_path.dentry;
+	btop = au_dbtop(dentry);
+	br = au_sbr(dentry->d_sb, btop);
+	h_file_tmp = NULL;
+	if (au_fbtop(file) == btop) {
+		h_file = au_hf_top(file);
+		if (file->f_mode == h_file->f_mode)
+			return 0; /* success */
+		h_file_tmp = h_file;
+		get_file(h_file_tmp);
+		au_lcnt_inc(&br->br_nfiles);
+		au_set_h_fptr(file, btop, NULL);
+	}
+	AuDebugOn(au_fi(file)->fi_hdir);
+	/*
+	 * it can happen
+	 * file exists on both of rw and ro
+	 * open --> dbtop and fbtop are both 0
+	 * prepend a branch as rw, "rw" become ro
+	 * remove rw/file
+	 * delete the top branch, "rw" becomes rw again
+	 *	--> dbtop is 1, fbtop is still 0
+	 * write --> fbtop is 0 but dbtop is 1
+	 */
+	/* AuDebugOn(au_fbtop(file) < btop); */
+
+	h_file = au_h_open(dentry, btop, vfsub_file_flags(file) & ~O_TRUNC,
+			   file, /*force_wr*/0);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file)) {
+		if (h_file_tmp) {
+			/* revert */
+			au_set_h_fptr(file, btop, h_file_tmp);
+			h_file_tmp = NULL;
+		}
+		goto out; /* todo: close all? */
+	}
+
+	err = 0;
+	au_set_fbtop(file, btop);
+	au_set_h_fptr(file, btop, h_file);
+	au_update_figen(file);
+	/* todo: necessary? */
+	/* file->f_ra = h_file->f_ra; */
+
+out:
+	if (h_file_tmp) {
+		fput(h_file_tmp);
+		au_lcnt_dec(&br->br_nfiles);
+	}
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_reopen_wh(struct file *file, aufs_bindex_t btgt,
+			struct dentry *hi_wh)
+{
+	int err;
+	aufs_bindex_t btop;
+	struct au_dinfo *dinfo;
+	struct dentry *h_dentry;
+	struct au_hdentry *hdp;
+
+	dinfo = au_di(file->f_path.dentry);
+	AuRwMustWriteLock(&dinfo->di_rwsem);
+
+	btop = dinfo->di_btop;
+	dinfo->di_btop = btgt;
+	hdp = au_hdentry(dinfo, btgt);
+	h_dentry = hdp->hd_dentry;
+	hdp->hd_dentry = hi_wh;
+	err = au_reopen_nondir(file);
+	hdp->hd_dentry = h_dentry;
+	dinfo->di_btop = btop;
+
+	return err;
+}
+
+static int au_ready_to_write_wh(struct file *file, loff_t len,
+				aufs_bindex_t bcpup, struct au_pin *pin)
+{
+	int err;
+	struct inode *inode, *h_inode;
+	struct dentry *h_dentry, *hi_wh;
+	struct au_cp_generic cpg = {
+		.dentry	= file->f_path.dentry,
+		.bdst	= bcpup,
+		.bsrc	= -1,
+		.len	= len,
+		.pin	= pin
+	};
+
+	au_update_dbtop(cpg.dentry);
+	inode = d_inode(cpg.dentry);
+	h_inode = NULL;
+	if (au_dbtop(cpg.dentry) <= bcpup
+	    && au_dbbot(cpg.dentry) >= bcpup) {
+		h_dentry = au_h_dptr(cpg.dentry, bcpup);
+		if (h_dentry && d_is_positive(h_dentry))
+			h_inode = d_inode(h_dentry);
+	}
+	hi_wh = au_hi_wh(inode, bcpup);
+	if (!hi_wh && !h_inode)
+		err = au_sio_cpup_wh(&cpg, file);
+	else
+		/* already copied-up after unlink */
+		err = au_reopen_wh(file, bcpup, hi_wh);
+
+	if (!err
+	    && (inode->i_nlink > 1
+		|| (inode->i_state & I_LINKABLE))
+	    && au_opt_test(au_mntflags(cpg.dentry->d_sb), PLINK))
+		au_plink_append(inode, bcpup, au_h_dptr(cpg.dentry, bcpup));
+
+	return err;
+}
+
+/*
+ * prepare the @file for writing.
+ */
+int au_ready_to_write(struct file *file, loff_t len, struct au_pin *pin)
+{
+	int err;
+	aufs_bindex_t dbtop;
+	struct dentry *parent;
+	struct inode *inode;
+	struct super_block *sb;
+	struct file *h_file;
+	struct au_cp_generic cpg = {
+		.dentry	= file->f_path.dentry,
+		.bdst	= -1,
+		.bsrc	= -1,
+		.len	= len,
+		.pin	= pin,
+		.flags	= AuCpup_DTIME
+	};
+
+	sb = cpg.dentry->d_sb;
+	inode = d_inode(cpg.dentry);
+	cpg.bsrc = au_fbtop(file);
+	err = au_test_ro(sb, cpg.bsrc, inode);
+	if (!err && (au_hf_top(file)->f_mode & FMODE_WRITE)) {
+		err = au_pin(pin, cpg.dentry, cpg.bsrc, AuOpt_UDBA_NONE,
+			     /*flags*/0);
+		goto out;
+	}
+
+	/* need to cpup or reopen */
+	parent = dget_parent(cpg.dentry);
+	di_write_lock_parent(parent);
+	err = AuWbrCopyup(au_sbi(sb), cpg.dentry);
+	cpg.bdst = err;
+	if (unlikely(err < 0))
+		goto out_dgrade;
+	err = 0;
+
+	if (!d_unhashed(cpg.dentry) && !au_h_dptr(parent, cpg.bdst)) {
+		err = au_cpup_dirs(cpg.dentry, cpg.bdst);
+		if (unlikely(err))
+			goto out_dgrade;
+	}
+
+	err = au_pin(pin, cpg.dentry, cpg.bdst, AuOpt_UDBA_NONE,
+		     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+	if (unlikely(err))
+		goto out_dgrade;
+
+	dbtop = au_dbtop(cpg.dentry);
+	if (dbtop <= cpg.bdst)
+		cpg.bsrc = cpg.bdst;
+
+	if (dbtop <= cpg.bdst		/* just reopen */
+	    || !d_unhashed(cpg.dentry)	/* copyup and reopen */
+		) {
+		h_file = au_h_open_pre(cpg.dentry, cpg.bsrc, /*force_wr*/0);
+		if (IS_ERR(h_file))
+			err = PTR_ERR(h_file);
+		else {
+			di_downgrade_lock(parent, AuLock_IR);
+			if (dbtop > cpg.bdst)
+				err = au_sio_cpup_simple(&cpg);
+			if (!err)
+				err = au_reopen_nondir(file);
+			au_h_open_post(cpg.dentry, cpg.bsrc, h_file);
+		}
+	} else {			/* copyup as wh and reopen */
+		/*
+		 * since writable hfsplus branch is not supported,
+		 * h_open_pre/post() are unnecessary.
+		 */
+		err = au_ready_to_write_wh(file, len, cpg.bdst, pin);
+		di_downgrade_lock(parent, AuLock_IR);
+	}
+
+	if (!err) {
+		au_pin_set_parent_lflag(pin, /*lflag*/0);
+		goto out_dput; /* success */
+	}
+	au_unpin(pin);
+	goto out_unlock;
+
+out_dgrade:
+	di_downgrade_lock(parent, AuLock_IR);
+out_unlock:
+	di_read_unlock(parent, AuLock_IR);
+out_dput:
+	dput(parent);
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_do_flush(struct file *file, fl_owner_t id,
+		int (*flush)(struct file *file, fl_owner_t id))
+{
+	int err;
+	struct super_block *sb;
+	struct inode *inode;
+
+	inode = file_inode(file);
+	sb = inode->i_sb;
+	si_noflush_read_lock(sb);
+	fi_read_lock(file);
+	ii_read_lock_child(inode);
+
+	err = flush(file, id);
+	au_cpup_attr_timesizes(inode);
+
+	ii_read_unlock(inode);
+	fi_read_unlock(file);
+	si_read_unlock(sb);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_file_refresh_by_inode(struct file *file, int *need_reopen)
+{
+	int err;
+	struct au_pin pin;
+	struct au_finfo *finfo;
+	struct dentry *parent, *hi_wh;
+	struct inode *inode;
+	struct super_block *sb;
+	struct au_cp_generic cpg = {
+		.dentry	= file->f_path.dentry,
+		.bdst	= -1,
+		.bsrc	= -1,
+		.len	= -1,
+		.pin	= &pin,
+		.flags	= AuCpup_DTIME
+	};
+
+	FiMustWriteLock(file);
+
+	err = 0;
+	finfo = au_fi(file);
+	sb = cpg.dentry->d_sb;
+	inode = d_inode(cpg.dentry);
+	cpg.bdst = au_ibtop(inode);
+	if (cpg.bdst == finfo->fi_btop || IS_ROOT(cpg.dentry))
+		goto out;
+
+	parent = dget_parent(cpg.dentry);
+	if (au_test_ro(sb, cpg.bdst, inode)) {
+		di_read_lock_parent(parent, !AuLock_IR);
+		err = AuWbrCopyup(au_sbi(sb), cpg.dentry);
+		cpg.bdst = err;
+		di_read_unlock(parent, !AuLock_IR);
+		if (unlikely(err < 0))
+			goto out_parent;
+		err = 0;
+	}
+
+	di_read_lock_parent(parent, AuLock_IR);
+	hi_wh = au_hi_wh(inode, cpg.bdst);
+	if (!S_ISDIR(inode->i_mode)
+	    && au_opt_test(au_mntflags(sb), PLINK)
+	    && au_plink_test(inode)
+	    && !d_unhashed(cpg.dentry)
+	    && cpg.bdst < au_dbtop(cpg.dentry)) {
+		err = au_test_and_cpup_dirs(cpg.dentry, cpg.bdst);
+		if (unlikely(err))
+			goto out_unlock;
+
+		/* always superio. */
+		err = au_pin(&pin, cpg.dentry, cpg.bdst, AuOpt_UDBA_NONE,
+			     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+		if (!err) {
+			err = au_sio_cpup_simple(&cpg);
+			au_unpin(&pin);
+		}
+	} else if (hi_wh) {
+		/* already copied-up after unlink */
+		err = au_reopen_wh(file, cpg.bdst, hi_wh);
+		*need_reopen = 0;
+	}
+
+out_unlock:
+	di_read_unlock(parent, AuLock_IR);
+out_parent:
+	dput(parent);
+out:
+	return err;
+}
+
+static void au_do_refresh_dir(struct file *file)
+{
+	aufs_bindex_t bindex, bbot, new_bindex, brid;
+	struct au_hfile *p, tmp, *q;
+	struct au_finfo *finfo;
+	struct super_block *sb;
+	struct au_fidir *fidir;
+
+	FiMustWriteLock(file);
+
+	sb = file->f_path.dentry->d_sb;
+	finfo = au_fi(file);
+	fidir = finfo->fi_hdir;
+	AuDebugOn(!fidir);
+	p = fidir->fd_hfile + finfo->fi_btop;
+	brid = p->hf_br->br_id;
+	bbot = fidir->fd_bbot;
+	for (bindex = finfo->fi_btop; bindex <= bbot; bindex++, p++) {
+		if (!p->hf_file)
+			continue;
+
+		new_bindex = au_br_index(sb, p->hf_br->br_id);
+		if (new_bindex == bindex)
+			continue;
+		if (new_bindex < 0) {
+			au_set_h_fptr(file, bindex, NULL);
+			continue;
+		}
+
+		/* swap two lower inode, and loop again */
+		q = fidir->fd_hfile + new_bindex;
+		tmp = *q;
+		*q = *p;
+		*p = tmp;
+		if (tmp.hf_file) {
+			bindex--;
+			p--;
+		}
+	}
+
+	p = fidir->fd_hfile;
+	if (!au_test_mmapped(file) && !d_unlinked(file->f_path.dentry)) {
+		bbot = au_sbbot(sb);
+		for (finfo->fi_btop = 0; finfo->fi_btop <= bbot;
+		     finfo->fi_btop++, p++)
+			if (p->hf_file) {
+				if (file_inode(p->hf_file))
+					break;
+				au_hfput(p, /*execed*/0);
+			}
+	} else {
+		bbot = au_br_index(sb, brid);
+		for (finfo->fi_btop = 0; finfo->fi_btop < bbot;
+		     finfo->fi_btop++, p++)
+			if (p->hf_file)
+				au_hfput(p, /*execed*/0);
+		bbot = au_sbbot(sb);
+	}
+
+	p = fidir->fd_hfile + bbot;
+	for (fidir->fd_bbot = bbot; fidir->fd_bbot >= finfo->fi_btop;
+	     fidir->fd_bbot--, p--)
+		if (p->hf_file) {
+			if (file_inode(p->hf_file))
+				break;
+			au_hfput(p, /*execed*/0);
+		}
+	AuDebugOn(fidir->fd_bbot < finfo->fi_btop);
+}
+
+/*
+ * after branch manipulating, refresh the file.
+ */
+static int refresh_file(struct file *file, int (*reopen)(struct file *file))
+{
+	int err, need_reopen, nbr;
+	aufs_bindex_t bbot, bindex;
+	struct dentry *dentry;
+	struct super_block *sb;
+	struct au_finfo *finfo;
+	struct au_hfile *hfile;
+
+	dentry = file->f_path.dentry;
+	sb = dentry->d_sb;
+	nbr = au_sbbot(sb) + 1;
+	finfo = au_fi(file);
+	if (!finfo->fi_hdir) {
+		hfile = &finfo->fi_htop;
+		AuDebugOn(!hfile->hf_file);
+		bindex = au_br_index(sb, hfile->hf_br->br_id);
+		AuDebugOn(bindex < 0);
+		if (bindex != finfo->fi_btop)
+			au_set_fbtop(file, bindex);
+	} else {
+		err = au_fidir_realloc(finfo, nbr, /*may_shrink*/0);
+		if (unlikely(err))
+			goto out;
+		au_do_refresh_dir(file);
+	}
+
+	err = 0;
+	need_reopen = 1;
+	if (!au_test_mmapped(file))
+		err = au_file_refresh_by_inode(file, &need_reopen);
+	if (finfo->fi_hdir)
+		/* harmless if err */
+		au_fidir_realloc(finfo, nbr, /*may_shrink*/1);
+	if (!err && need_reopen && !d_unlinked(dentry))
+		err = reopen(file);
+	if (!err) {
+		au_update_figen(file);
+		goto out; /* success */
+	}
+
+	/* error, close all lower files */
+	if (finfo->fi_hdir) {
+		bbot = au_fbbot_dir(file);
+		for (bindex = au_fbtop(file); bindex <= bbot; bindex++)
+			au_set_h_fptr(file, bindex, NULL);
+	}
+
+out:
+	return err;
+}
+
+/* common function to regular file and dir */
+int au_reval_and_lock_fdi(struct file *file, int (*reopen)(struct file *file),
+			  int wlock, unsigned int fi_lsc)
+{
+	int err;
+	unsigned int sigen, figen;
+	aufs_bindex_t btop;
+	unsigned char pseudo_link;
+	struct dentry *dentry;
+	struct inode *inode;
+
+	err = 0;
+	dentry = file->f_path.dentry;
+	inode = d_inode(dentry);
+	sigen = au_sigen(dentry->d_sb);
+	fi_write_lock_nested(file, fi_lsc);
+	figen = au_figen(file);
+	if (!fi_lsc)
+		di_write_lock_child(dentry);
+	else
+		di_write_lock_child2(dentry);
+	btop = au_dbtop(dentry);
+	pseudo_link = (btop != au_ibtop(inode));
+	if (sigen == figen && !pseudo_link && au_fbtop(file) == btop) {
+		if (!wlock) {
+			di_downgrade_lock(dentry, AuLock_IR);
+			fi_downgrade_lock(file);
+		}
+		goto out; /* success */
+	}
+
+	AuDbg("sigen %d, figen %d\n", sigen, figen);
+	if (au_digen_test(dentry, sigen)) {
+		err = au_reval_dpath(dentry, sigen);
+		AuDebugOn(!err && au_digen_test(dentry, sigen));
+	}
+
+	if (!err)
+		err = refresh_file(file, reopen);
+	if (!err) {
+		if (!wlock) {
+			di_downgrade_lock(dentry, AuLock_IR);
+			fi_downgrade_lock(file);
+		}
+	} else {
+		di_write_unlock(dentry);
+		fi_write_unlock(file);
+	}
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* cf. aufs_nopage() */
+/* for madvise(2) */
+static int aufs_readpage(struct file *file __maybe_unused, struct page *page)
+{
+	unlock_page(page);
+	return 0;
+}
+
+/* it will never be called, but necessary to support O_DIRECT */
+static ssize_t aufs_direct_IO(struct kiocb *iocb, struct iov_iter *iter)
+{ BUG(); return 0; }
+
+/* they will never be called. */
+#ifdef CONFIG_AUFS_DEBUG
+static int aufs_write_begin(struct file *file, struct address_space *mapping,
+			    loff_t pos, unsigned len, unsigned flags,
+			    struct page **pagep, void **fsdata)
+{ AuUnsupport(); return 0; }
+static int aufs_write_end(struct file *file, struct address_space *mapping,
+			  loff_t pos, unsigned len, unsigned copied,
+			  struct page *page, void *fsdata)
+{ AuUnsupport(); return 0; }
+static int aufs_writepage(struct page *page, struct writeback_control *wbc)
+{ AuUnsupport(); return 0; }
+
+static int aufs_set_page_dirty(struct page *page)
+{ AuUnsupport(); return 0; }
+static void aufs_invalidatepage(struct page *page, unsigned int offset,
+				unsigned int length)
+{ AuUnsupport(); }
+static int aufs_releasepage(struct page *page, gfp_t gfp)
+{ AuUnsupport(); return 0; }
+#if 0 /* called by memory compaction regardless file */
+static int aufs_migratepage(struct address_space *mapping, struct page *newpage,
+			    struct page *page, enum migrate_mode mode)
+{ AuUnsupport(); return 0; }
+#endif
+static bool aufs_isolate_page(struct page *page, isolate_mode_t mode)
+{ AuUnsupport(); return true; }
+static void aufs_putback_page(struct page *page)
+{ AuUnsupport(); }
+static int aufs_launder_page(struct page *page)
+{ AuUnsupport(); return 0; }
+static int aufs_is_partially_uptodate(struct page *page,
+				      unsigned long from,
+				      unsigned long count)
+{ AuUnsupport(); return 0; }
+static void aufs_is_dirty_writeback(struct page *page, bool *dirty,
+				    bool *writeback)
+{ AuUnsupport(); }
+static int aufs_error_remove_page(struct address_space *mapping,
+				  struct page *page)
+{ AuUnsupport(); return 0; }
+static int aufs_swap_activate(struct swap_info_struct *sis, struct file *file,
+			      sector_t *span)
+{ AuUnsupport(); return 0; }
+static void aufs_swap_deactivate(struct file *file)
+{ AuUnsupport(); }
+#endif /* CONFIG_AUFS_DEBUG */
+
+const struct address_space_operations aufs_aop = {
+	.readpage		= aufs_readpage,
+	.direct_IO		= aufs_direct_IO,
+#ifdef CONFIG_AUFS_DEBUG
+	.writepage		= aufs_writepage,
+	/* no writepages, because of writepage */
+	.set_page_dirty		= aufs_set_page_dirty,
+	/* no readpages, because of readpage */
+	.write_begin		= aufs_write_begin,
+	.write_end		= aufs_write_end,
+	/* no bmap, no block device */
+	.invalidatepage		= aufs_invalidatepage,
+	.releasepage		= aufs_releasepage,
+	/* is fallback_migrate_page ok? */
+	/* .migratepage		= aufs_migratepage, */
+	.isolate_page		= aufs_isolate_page,
+	.putback_page		= aufs_putback_page,
+	.launder_page		= aufs_launder_page,
+	.is_partially_uptodate	= aufs_is_partially_uptodate,
+	.is_dirty_writeback	= aufs_is_dirty_writeback,
+	.error_remove_page	= aufs_error_remove_page,
+	.swap_activate		= aufs_swap_activate,
+	.swap_deactivate	= aufs_swap_deactivate
+#endif /* CONFIG_AUFS_DEBUG */
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/file.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/file.h
@@ -0,0 +1,342 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * file operations
+ */
+
+#ifndef __AUFS_FILE_H__
+#define __AUFS_FILE_H__
+
+#ifdef __KERNEL__
+
+#include <linux/file.h>
+#include <linux/fs.h>
+#include <linux/mm_types.h>
+#include <linux/poll.h>
+#include "rwsem.h"
+
+struct au_branch;
+struct au_hfile {
+	struct file		*hf_file;
+	struct au_branch	*hf_br;
+};
+
+struct au_vdir;
+struct au_fidir {
+	aufs_bindex_t		fd_bbot;
+	aufs_bindex_t		fd_nent;
+	struct au_vdir		*fd_vdir_cache;
+	struct au_hfile		fd_hfile[];
+};
+
+static inline int au_fidir_sz(int nent)
+{
+	AuDebugOn(nent < 0);
+	return sizeof(struct au_fidir) + sizeof(struct au_hfile) * nent;
+}
+
+struct au_finfo {
+	atomic_t		fi_generation;
+
+	struct au_rwsem		fi_rwsem;
+	aufs_bindex_t		fi_btop;
+
+	/* do not union them */
+	struct {				/* for non-dir */
+		struct au_hfile			fi_htop;
+		atomic_t			fi_mmapped;
+	};
+	struct au_fidir		*fi_hdir;	/* for dir only */
+
+	struct hlist_bl_node	fi_hlist;
+	struct file		*fi_file;	/* very ugly */
+	struct rcu_head		rcu;
+} ____cacheline_aligned_in_smp;
+
+/* ---------------------------------------------------------------------- */
+
+/* file.c */
+extern const struct address_space_operations aufs_aop;
+unsigned int au_file_roflags(unsigned int flags);
+struct file *au_h_open(struct dentry *dentry, aufs_bindex_t bindex, int flags,
+		       struct file *file, int force_wr);
+struct au_do_open_args {
+	int		aopen;
+	int		(*open)(struct file *file, int flags,
+				struct file *h_file);
+	struct au_fidir	*fidir;
+	struct file	*h_file;
+};
+int au_do_open(struct file *file, struct au_do_open_args *args);
+int au_reopen_nondir(struct file *file);
+struct au_pin;
+int au_ready_to_write(struct file *file, loff_t len, struct au_pin *pin);
+int au_reval_and_lock_fdi(struct file *file, int (*reopen)(struct file *file),
+			  int wlock, unsigned int fi_lsc);
+int au_do_flush(struct file *file, fl_owner_t id,
+		int (*flush)(struct file *file, fl_owner_t id));
+
+/* poll.c */
+#ifdef CONFIG_AUFS_POLL
+__poll_t aufs_poll(struct file *file, struct poll_table_struct *pt);
+#endif
+
+#ifdef CONFIG_AUFS_BR_HFSPLUS
+/* hfsplus.c */
+struct file *au_h_open_pre(struct dentry *dentry, aufs_bindex_t bindex,
+			   int force_wr);
+void au_h_open_post(struct dentry *dentry, aufs_bindex_t bindex,
+		    struct file *h_file);
+#else
+AuStub(struct file *, au_h_open_pre, return NULL, struct dentry *dentry,
+       aufs_bindex_t bindex, int force_wr)
+AuStubVoid(au_h_open_post, struct dentry *dentry, aufs_bindex_t bindex,
+	   struct file *h_file);
+#endif
+
+/* f_op.c */
+extern const struct file_operations aufs_file_fop;
+int au_do_open_nondir(struct file *file, int flags, struct file *h_file);
+int aufs_release_nondir(struct inode *inode __maybe_unused, struct file *file);
+struct file *au_read_pre(struct file *file, int keep_fi, unsigned int lsc);
+
+/* finfo.c */
+void au_hfput(struct au_hfile *hf, int execed);
+void au_set_h_fptr(struct file *file, aufs_bindex_t bindex,
+		   struct file *h_file);
+
+void au_update_figen(struct file *file);
+struct au_fidir *au_fidir_alloc(struct super_block *sb);
+int au_fidir_realloc(struct au_finfo *finfo, int nbr, int may_shrink);
+
+void au_fi_init_once(void *_fi);
+void au_finfo_fin(struct file *file);
+int au_finfo_init(struct file *file, struct au_fidir *fidir);
+
+/* ioctl.c */
+long aufs_ioctl_nondir(struct file *file, unsigned int cmd, unsigned long arg);
+#ifdef CONFIG_COMPAT
+long aufs_compat_ioctl_dir(struct file *file, unsigned int cmd,
+			   unsigned long arg);
+long aufs_compat_ioctl_nondir(struct file *file, unsigned int cmd,
+			      unsigned long arg);
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct au_finfo *au_fi(struct file *file)
+{
+	return file->private_data;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#define fi_read_lock(f)	au_rw_read_lock(&au_fi(f)->fi_rwsem)
+#define fi_write_lock(f)	au_rw_write_lock(&au_fi(f)->fi_rwsem)
+#define fi_read_trylock(f)	au_rw_read_trylock(&au_fi(f)->fi_rwsem)
+#define fi_write_trylock(f)	au_rw_write_trylock(&au_fi(f)->fi_rwsem)
+/*
+#define fi_read_trylock_nested(f) \
+	au_rw_read_trylock_nested(&au_fi(f)->fi_rwsem)
+#define fi_write_trylock_nested(f) \
+	au_rw_write_trylock_nested(&au_fi(f)->fi_rwsem)
+*/
+
+#define fi_read_unlock(f)	au_rw_read_unlock(&au_fi(f)->fi_rwsem)
+#define fi_write_unlock(f)	au_rw_write_unlock(&au_fi(f)->fi_rwsem)
+#define fi_downgrade_lock(f)	au_rw_dgrade_lock(&au_fi(f)->fi_rwsem)
+
+/* lock subclass for finfo */
+enum {
+	AuLsc_FI_1,
+	AuLsc_FI_2
+};
+
+static inline void fi_read_lock_nested(struct file *f, unsigned int lsc)
+{
+	au_rw_read_lock_nested(&au_fi(f)->fi_rwsem, lsc);
+}
+
+static inline void fi_write_lock_nested(struct file *f, unsigned int lsc)
+{
+	au_rw_write_lock_nested(&au_fi(f)->fi_rwsem, lsc);
+}
+
+/*
+ * fi_read_lock_1, fi_write_lock_1,
+ * fi_read_lock_2, fi_write_lock_2
+ */
+#define AuReadLockFunc(name) \
+static inline void fi_read_lock_##name(struct file *f) \
+{ fi_read_lock_nested(f, AuLsc_FI_##name); }
+
+#define AuWriteLockFunc(name) \
+static inline void fi_write_lock_##name(struct file *f) \
+{ fi_write_lock_nested(f, AuLsc_FI_##name); }
+
+#define AuRWLockFuncs(name) \
+	AuReadLockFunc(name) \
+	AuWriteLockFunc(name)
+
+AuRWLockFuncs(1);
+AuRWLockFuncs(2);
+
+#undef AuReadLockFunc
+#undef AuWriteLockFunc
+#undef AuRWLockFuncs
+
+#define FiMustNoWaiters(f)	AuRwMustNoWaiters(&au_fi(f)->fi_rwsem)
+#define FiMustAnyLock(f)	AuRwMustAnyLock(&au_fi(f)->fi_rwsem)
+#define FiMustWriteLock(f)	AuRwMustWriteLock(&au_fi(f)->fi_rwsem)
+
+/* ---------------------------------------------------------------------- */
+
+/* todo: hard/soft set? */
+static inline aufs_bindex_t au_fbtop(struct file *file)
+{
+	FiMustAnyLock(file);
+	return au_fi(file)->fi_btop;
+}
+
+static inline aufs_bindex_t au_fbbot_dir(struct file *file)
+{
+	FiMustAnyLock(file);
+	AuDebugOn(!au_fi(file)->fi_hdir);
+	return au_fi(file)->fi_hdir->fd_bbot;
+}
+
+static inline struct au_vdir *au_fvdir_cache(struct file *file)
+{
+	FiMustAnyLock(file);
+	AuDebugOn(!au_fi(file)->fi_hdir);
+	return au_fi(file)->fi_hdir->fd_vdir_cache;
+}
+
+static inline void au_set_fbtop(struct file *file, aufs_bindex_t bindex)
+{
+	FiMustWriteLock(file);
+	au_fi(file)->fi_btop = bindex;
+}
+
+static inline void au_set_fbbot_dir(struct file *file, aufs_bindex_t bindex)
+{
+	FiMustWriteLock(file);
+	AuDebugOn(!au_fi(file)->fi_hdir);
+	au_fi(file)->fi_hdir->fd_bbot = bindex;
+}
+
+static inline void au_set_fvdir_cache(struct file *file,
+				      struct au_vdir *vdir_cache)
+{
+	FiMustWriteLock(file);
+	AuDebugOn(!au_fi(file)->fi_hdir);
+	au_fi(file)->fi_hdir->fd_vdir_cache = vdir_cache;
+}
+
+static inline struct file *au_hf_top(struct file *file)
+{
+	FiMustAnyLock(file);
+	AuDebugOn(au_fi(file)->fi_hdir);
+	return au_fi(file)->fi_htop.hf_file;
+}
+
+static inline struct file *au_hf_dir(struct file *file, aufs_bindex_t bindex)
+{
+	FiMustAnyLock(file);
+	AuDebugOn(!au_fi(file)->fi_hdir);
+	return au_fi(file)->fi_hdir->fd_hfile[0 + bindex].hf_file;
+}
+
+/* todo: memory barrier? */
+static inline unsigned int au_figen(struct file *f)
+{
+	return atomic_read(&au_fi(f)->fi_generation);
+}
+
+static inline void au_set_mmapped(struct file *f)
+{
+	if (atomic_inc_return(&au_fi(f)->fi_mmapped))
+		return;
+	pr_warn("fi_mmapped wrapped around\n");
+	while (!atomic_inc_return(&au_fi(f)->fi_mmapped))
+		;
+}
+
+static inline void au_unset_mmapped(struct file *f)
+{
+	atomic_dec(&au_fi(f)->fi_mmapped);
+}
+
+static inline int au_test_mmapped(struct file *f)
+{
+	return atomic_read(&au_fi(f)->fi_mmapped);
+}
+
+/* customize vma->vm_file */
+
+static inline void au_do_vm_file_reset(struct vm_area_struct *vma,
+				       struct file *file)
+{
+	struct file *f;
+
+	f = vma->vm_file;
+	get_file(file);
+	vma->vm_file = file;
+	fput(f);
+}
+
+#ifdef CONFIG_MMU
+#define AuDbgVmRegion(file, vma) do {} while (0)
+
+static inline void au_vm_file_reset(struct vm_area_struct *vma,
+				    struct file *file)
+{
+	au_do_vm_file_reset(vma, file);
+}
+#else
+#define AuDbgVmRegion(file, vma) \
+	AuDebugOn((vma)->vm_region && (vma)->vm_region->vm_file != (file))
+
+static inline void au_vm_file_reset(struct vm_area_struct *vma,
+				    struct file *file)
+{
+	struct file *f;
+
+	au_do_vm_file_reset(vma, file);
+	f = vma->vm_region->vm_file;
+	get_file(file);
+	vma->vm_region->vm_file = file;
+	fput(f);
+}
+#endif /* CONFIG_MMU */
+
+/* handle vma->vm_prfile */
+static inline void au_vm_prfile_set(struct vm_area_struct *vma,
+				    struct file *file)
+{
+	get_file(file);
+	vma->vm_prfile = file;
+#ifndef CONFIG_MMU
+	get_file(file);
+	vma->vm_region->vm_prfile = file;
+#endif
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_FILE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/finfo.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/finfo.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * file private data
+ */
+
+#include "aufs.h"
+
+void au_hfput(struct au_hfile *hf, int execed)
+{
+	if (execed)
+		allow_write_access(hf->hf_file);
+	fput(hf->hf_file);
+	hf->hf_file = NULL;
+	au_lcnt_dec(&hf->hf_br->br_nfiles);
+	hf->hf_br = NULL;
+}
+
+void au_set_h_fptr(struct file *file, aufs_bindex_t bindex, struct file *val)
+{
+	struct au_finfo *finfo = au_fi(file);
+	struct au_hfile *hf;
+	struct au_fidir *fidir;
+
+	fidir = finfo->fi_hdir;
+	if (!fidir) {
+		AuDebugOn(finfo->fi_btop != bindex);
+		hf = &finfo->fi_htop;
+	} else
+		hf = fidir->fd_hfile + bindex;
+
+	if (hf && hf->hf_file)
+		au_hfput(hf, vfsub_file_execed(file));
+	if (val) {
+		FiMustWriteLock(file);
+		AuDebugOn(IS_ERR_OR_NULL(file->f_path.dentry));
+		hf->hf_file = val;
+		hf->hf_br = au_sbr(file->f_path.dentry->d_sb, bindex);
+	}
+}
+
+void au_update_figen(struct file *file)
+{
+	atomic_set(&au_fi(file)->fi_generation, au_digen(file->f_path.dentry));
+	/* smp_mb(); */ /* atomic_set */
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_fidir *au_fidir_alloc(struct super_block *sb)
+{
+	struct au_fidir *fidir;
+	int nbr;
+
+	nbr = au_sbbot(sb) + 1;
+	if (nbr < 2)
+		nbr = 2; /* initial allocate for 2 branches */
+	fidir = kzalloc(au_fidir_sz(nbr), GFP_NOFS);
+	if (fidir) {
+		fidir->fd_bbot = -1;
+		fidir->fd_nent = nbr;
+	}
+
+	return fidir;
+}
+
+int au_fidir_realloc(struct au_finfo *finfo, int nbr, int may_shrink)
+{
+	int err;
+	struct au_fidir *fidir, *p;
+
+	AuRwMustWriteLock(&finfo->fi_rwsem);
+	fidir = finfo->fi_hdir;
+	AuDebugOn(!fidir);
+
+	err = -ENOMEM;
+	p = au_kzrealloc(fidir, au_fidir_sz(fidir->fd_nent), au_fidir_sz(nbr),
+			 GFP_NOFS, may_shrink);
+	if (p) {
+		p->fd_nent = nbr;
+		finfo->fi_hdir = p;
+		err = 0;
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_finfo_fin(struct file *file)
+{
+	struct au_finfo *finfo;
+
+	au_lcnt_dec(&au_sbi(file->f_path.dentry->d_sb)->si_nfiles);
+
+	finfo = au_fi(file);
+	AuDebugOn(finfo->fi_hdir);
+	AuRwDestroy(&finfo->fi_rwsem);
+	au_cache_free_finfo(finfo);
+}
+
+void au_fi_init_once(void *_finfo)
+{
+	struct au_finfo *finfo = _finfo;
+
+	au_rw_init(&finfo->fi_rwsem);
+}
+
+int au_finfo_init(struct file *file, struct au_fidir *fidir)
+{
+	int err;
+	struct au_finfo *finfo;
+	struct dentry *dentry;
+
+	err = -ENOMEM;
+	dentry = file->f_path.dentry;
+	finfo = au_cache_alloc_finfo();
+	if (unlikely(!finfo))
+		goto out;
+
+	err = 0;
+	au_lcnt_inc(&au_sbi(dentry->d_sb)->si_nfiles);
+	au_rw_write_lock(&finfo->fi_rwsem);
+	finfo->fi_btop = -1;
+	finfo->fi_hdir = fidir;
+	atomic_set(&finfo->fi_generation, au_digen(dentry));
+	/* smp_mb(); */ /* atomic_set */
+
+	file->private_data = finfo;
+
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/fstype.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/fstype.h
@@ -0,0 +1,401 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * judging filesystem type
+ */
+
+#ifndef __AUFS_FSTYPE_H__
+#define __AUFS_FSTYPE_H__
+
+#ifdef __KERNEL__
+
+#include <linux/fs.h>
+#include <linux/magic.h>
+#include <linux/nfs_fs.h>
+#include <linux/romfs_fs.h>
+
+static inline int au_test_aufs(struct super_block *sb)
+{
+	return sb->s_magic == AUFS_SUPER_MAGIC;
+}
+
+static inline const char *au_sbtype(struct super_block *sb)
+{
+	return sb->s_type->name;
+}
+
+static inline int au_test_iso9660(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_ISO9660_FS)
+	return sb->s_magic == ISOFS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_romfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_ROMFS_FS)
+	return sb->s_magic == ROMFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_cramfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_CRAMFS)
+	return sb->s_magic == CRAMFS_MAGIC;
+#endif
+	return 0;
+}
+
+static inline int au_test_nfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_NFS_FS)
+	return sb->s_magic == NFS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_fuse(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_FUSE_FS)
+	return sb->s_magic == FUSE_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_xfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_XFS_FS)
+	return sb->s_magic == XFS_SB_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_tmpfs(struct super_block *sb __maybe_unused)
+{
+#ifdef CONFIG_TMPFS
+	return sb->s_magic == TMPFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_ecryptfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_ECRYPT_FS)
+	return !strcmp(au_sbtype(sb), "ecryptfs");
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_ramfs(struct super_block *sb)
+{
+	return sb->s_magic == RAMFS_MAGIC;
+}
+
+static inline int au_test_ubifs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_UBIFS_FS)
+	return sb->s_magic == UBIFS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_procfs(struct super_block *sb __maybe_unused)
+{
+#ifdef CONFIG_PROC_FS
+	return sb->s_magic == PROC_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_sysfs(struct super_block *sb __maybe_unused)
+{
+#ifdef CONFIG_SYSFS
+	return sb->s_magic == SYSFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_configfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_CONFIGFS_FS)
+	return sb->s_magic == CONFIGFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_minix(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_MINIX_FS)
+	return sb->s_magic == MINIX3_SUPER_MAGIC
+		|| sb->s_magic == MINIX2_SUPER_MAGIC
+		|| sb->s_magic == MINIX2_SUPER_MAGIC2
+		|| sb->s_magic == MINIX_SUPER_MAGIC
+		|| sb->s_magic == MINIX_SUPER_MAGIC2;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_fat(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_FAT_FS)
+	return sb->s_magic == MSDOS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_msdos(struct super_block *sb)
+{
+	return au_test_fat(sb);
+}
+
+static inline int au_test_vfat(struct super_block *sb)
+{
+	return au_test_fat(sb);
+}
+
+static inline int au_test_securityfs(struct super_block *sb __maybe_unused)
+{
+#ifdef CONFIG_SECURITYFS
+	return sb->s_magic == SECURITYFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_squashfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_SQUASHFS)
+	return sb->s_magic == SQUASHFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_btrfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_BTRFS_FS)
+	return sb->s_magic == BTRFS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_xenfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_XENFS)
+	return sb->s_magic == XENFS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_debugfs(struct super_block *sb __maybe_unused)
+{
+#ifdef CONFIG_DEBUG_FS
+	return sb->s_magic == DEBUGFS_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_nilfs(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_NILFS)
+	return sb->s_magic == NILFS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+static inline int au_test_hfsplus(struct super_block *sb __maybe_unused)
+{
+#if IS_ENABLED(CONFIG_HFSPLUS_FS)
+	return sb->s_magic == HFSPLUS_SUPER_MAGIC;
+#else
+	return 0;
+#endif
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * they can't be an aufs branch.
+ */
+static inline int au_test_fs_unsuppoted(struct super_block *sb)
+{
+	return
+#ifndef CONFIG_AUFS_BR_RAMFS
+		au_test_ramfs(sb) ||
+#endif
+		au_test_procfs(sb)
+		|| au_test_sysfs(sb)
+		|| au_test_configfs(sb)
+		|| au_test_debugfs(sb)
+		|| au_test_securityfs(sb)
+		|| au_test_xenfs(sb)
+		|| au_test_ecryptfs(sb)
+		/* || !strcmp(au_sbtype(sb), "unionfs") */
+		|| au_test_aufs(sb); /* will be supported in next version */
+}
+
+static inline int au_test_fs_remote(struct super_block *sb)
+{
+	return !au_test_tmpfs(sb)
+#ifdef CONFIG_AUFS_BR_RAMFS
+		&& !au_test_ramfs(sb)
+#endif
+		&& !(sb->s_type->fs_flags & FS_REQUIRES_DEV);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * Note: these functions (below) are created after reading ->getattr() in all
+ * filesystems under linux/fs. it means we have to do so in every update...
+ */
+
+/*
+ * some filesystems require getattr to refresh the inode attributes before
+ * referencing.
+ * in most cases, we can rely on the inode attribute in NFS (or every remote fs)
+ * and leave the work for d_revalidate()
+ */
+static inline int au_test_fs_refresh_iattr(struct super_block *sb)
+{
+	return au_test_nfs(sb)
+		|| au_test_fuse(sb)
+		/* || au_test_btrfs(sb) */	/* untested */
+		;
+}
+
+/*
+ * filesystems which don't maintain i_size or i_blocks.
+ */
+static inline int au_test_fs_bad_iattr_size(struct super_block *sb)
+{
+	return au_test_xfs(sb)
+		|| au_test_btrfs(sb)
+		|| au_test_ubifs(sb)
+		|| au_test_hfsplus(sb)	/* maintained, but incorrect */
+		/* || au_test_minix(sb) */	/* untested */
+		;
+}
+
+/*
+ * filesystems which don't store the correct value in some of their inode
+ * attributes.
+ */
+static inline int au_test_fs_bad_iattr(struct super_block *sb)
+{
+	return au_test_fs_bad_iattr_size(sb)
+		|| au_test_fat(sb)
+		|| au_test_msdos(sb)
+		|| au_test_vfat(sb);
+}
+
+/* they don't check i_nlink in link(2) */
+static inline int au_test_fs_no_limit_nlink(struct super_block *sb)
+{
+	return au_test_tmpfs(sb)
+#ifdef CONFIG_AUFS_BR_RAMFS
+		|| au_test_ramfs(sb)
+#endif
+		|| au_test_ubifs(sb)
+		|| au_test_hfsplus(sb);
+}
+
+/*
+ * filesystems which sets S_NOATIME and S_NOCMTIME.
+ */
+static inline int au_test_fs_notime(struct super_block *sb)
+{
+	return au_test_nfs(sb)
+		|| au_test_fuse(sb)
+		|| au_test_ubifs(sb)
+		;
+}
+
+/* temporary support for i#1 in cramfs */
+static inline int au_test_fs_unique_ino(struct inode *inode)
+{
+	if (au_test_cramfs(inode->i_sb))
+		return inode->i_ino != 1;
+	return 1;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * the filesystem where the xino files placed must support i/o after unlink and
+ * maintain i_size and i_blocks.
+ */
+static inline int au_test_fs_bad_xino(struct super_block *sb)
+{
+	return au_test_fs_remote(sb)
+		|| au_test_fs_bad_iattr_size(sb)
+		/* don't want unnecessary work for xino */
+		|| au_test_aufs(sb)
+		|| au_test_ecryptfs(sb)
+		|| au_test_nilfs(sb);
+}
+
+static inline int au_test_fs_trunc_xino(struct super_block *sb)
+{
+	return au_test_tmpfs(sb)
+		|| au_test_ramfs(sb);
+}
+
+/*
+ * test if the @sb is real-readonly.
+ */
+static inline int au_test_fs_rr(struct super_block *sb)
+{
+	return au_test_squashfs(sb)
+		|| au_test_iso9660(sb)
+		|| au_test_cramfs(sb)
+		|| au_test_romfs(sb);
+}
+
+/*
+ * test if the @inode is nfs with 'noacl' option
+ * NFS always sets SB_POSIXACL regardless its mount option 'noacl.'
+ */
+static inline int au_test_nfs_noacl(struct inode *inode)
+{
+	return au_test_nfs(inode->i_sb)
+		/* && IS_POSIXACL(inode) */
+		&& !nfs_server_capable(inode, NFS_CAP_ACLS);
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_FSTYPE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/hbl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/hbl.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2017-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * helpers for hlist_bl.h
+ */
+
+#ifndef __AUFS_HBL_H__
+#define __AUFS_HBL_H__
+
+#ifdef __KERNEL__
+
+#include <linux/list_bl.h>
+
+static inline void au_hbl_add(struct hlist_bl_node *node,
+			      struct hlist_bl_head *hbl)
+{
+	hlist_bl_lock(hbl);
+	hlist_bl_add_head(node, hbl);
+	hlist_bl_unlock(hbl);
+}
+
+static inline void au_hbl_del(struct hlist_bl_node *node,
+			      struct hlist_bl_head *hbl)
+{
+	hlist_bl_lock(hbl);
+	hlist_bl_del(node);
+	hlist_bl_unlock(hbl);
+}
+
+#define au_hbl_for_each(pos, head)					\
+	for (pos = hlist_bl_first(head);				\
+	     pos;							\
+	     pos = pos->next)
+
+static inline unsigned long au_hbl_count(struct hlist_bl_head *hbl)
+{
+	unsigned long cnt;
+	struct hlist_bl_node *pos;
+
+	cnt = 0;
+	hlist_bl_lock(hbl);
+	au_hbl_for_each(pos, hbl)
+		cnt++;
+	hlist_bl_unlock(hbl);
+	return cnt;
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_HBL_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/hfsnotify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/hfsnotify.c
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * fsnotify for the lower directories
+ */
+
+#include "aufs.h"
+
+/* FS_IN_IGNORED is unnecessary */
+static const __u32 AuHfsnMask = (FS_MOVED_TO | FS_MOVED_FROM | FS_DELETE
+				 | FS_CREATE | FS_EVENT_ON_CHILD);
+static DECLARE_WAIT_QUEUE_HEAD(au_hfsn_wq);
+static __cacheline_aligned_in_smp atomic64_t au_hfsn_ifree = ATOMIC64_INIT(0);
+
+static void au_hfsn_free_mark(struct fsnotify_mark *mark)
+{
+	struct au_hnotify *hn = container_of(mark, struct au_hnotify,
+					     hn_mark);
+	/* AuDbg("here\n"); */
+	au_cache_free_hnotify(hn);
+	smp_mb__before_atomic(); /* for atomic64_dec */
+	if (atomic64_dec_and_test(&au_hfsn_ifree))
+		wake_up(&au_hfsn_wq);
+}
+
+static int au_hfsn_alloc(struct au_hinode *hinode)
+{
+	int err;
+	struct au_hnotify *hn;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct fsnotify_mark *mark;
+	aufs_bindex_t bindex;
+
+	hn = hinode->hi_notify;
+	sb = hn->hn_aufs_inode->i_sb;
+	bindex = au_br_index(sb, hinode->hi_id);
+	br = au_sbr(sb, bindex);
+	AuDebugOn(!br->br_hfsn);
+
+	mark = &hn->hn_mark;
+	fsnotify_init_mark(mark, br->br_hfsn->hfsn_group);
+	mark->mask = AuHfsnMask;
+	/*
+	 * by udba rename or rmdir, aufs assign a new inode to the known
+	 * h_inode, so specify 1 to allow dups.
+	 */
+	lockdep_off();
+	err = fsnotify_add_inode_mark(mark, hinode->hi_inode, /*allow_dups*/1);
+	lockdep_on();
+
+	return err;
+}
+
+static int au_hfsn_free(struct au_hinode *hinode, struct au_hnotify *hn)
+{
+	struct fsnotify_mark *mark;
+	unsigned long long ull;
+	struct fsnotify_group *group;
+
+	ull = atomic64_inc_return(&au_hfsn_ifree);
+	BUG_ON(!ull);
+
+	mark = &hn->hn_mark;
+	spin_lock(&mark->lock);
+	group = mark->group;
+	fsnotify_get_group(group);
+	spin_unlock(&mark->lock);
+	lockdep_off();
+	fsnotify_destroy_mark(mark, group);
+	fsnotify_put_mark(mark);
+	fsnotify_put_group(group);
+	lockdep_on();
+
+	/* free hn by myself */
+	return 0;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void au_hfsn_ctl(struct au_hinode *hinode, int do_set)
+{
+	struct fsnotify_mark *mark;
+
+	mark = &hinode->hi_notify->hn_mark;
+	spin_lock(&mark->lock);
+	if (do_set) {
+		AuDebugOn(mark->mask & AuHfsnMask);
+		mark->mask |= AuHfsnMask;
+	} else {
+		AuDebugOn(!(mark->mask & AuHfsnMask));
+		mark->mask &= ~AuHfsnMask;
+	}
+	spin_unlock(&mark->lock);
+	/* fsnotify_recalc_inode_mask(hinode->hi_inode); */
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* #define AuDbgHnotify */
+#ifdef AuDbgHnotify
+static char *au_hfsn_name(u32 mask)
+{
+#ifdef CONFIG_AUFS_DEBUG
+#define test_ret(flag)				\
+	do {					\
+		if (mask & flag)		\
+			return #flag;		\
+	} while (0)
+	test_ret(FS_ACCESS);
+	test_ret(FS_MODIFY);
+	test_ret(FS_ATTRIB);
+	test_ret(FS_CLOSE_WRITE);
+	test_ret(FS_CLOSE_NOWRITE);
+	test_ret(FS_OPEN);
+	test_ret(FS_MOVED_FROM);
+	test_ret(FS_MOVED_TO);
+	test_ret(FS_CREATE);
+	test_ret(FS_DELETE);
+	test_ret(FS_DELETE_SELF);
+	test_ret(FS_MOVE_SELF);
+	test_ret(FS_UNMOUNT);
+	test_ret(FS_Q_OVERFLOW);
+	test_ret(FS_IN_IGNORED);
+	test_ret(FS_ISDIR);
+	test_ret(FS_IN_ONESHOT);
+	test_ret(FS_EVENT_ON_CHILD);
+	return "";
+#undef test_ret
+#else
+	return "??";
+#endif
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+static void au_hfsn_free_group(struct fsnotify_group *group)
+{
+	struct au_br_hfsnotify *hfsn = group->private;
+
+	/* AuDbg("here\n"); */
+	au_kfree_try_rcu(hfsn);
+}
+
+static int au_hfsn_handle_event(struct fsnotify_group *group,
+				u32 mask, const void *data, int data_type,
+				struct inode *dir,
+				const struct qstr *file_name, u32 cookie,
+				struct fsnotify_iter_info *iter_info)
+{
+	int err;
+	struct au_hnotify *hnotify;
+	struct inode *h_dir, *h_inode;
+	struct fsnotify_mark *inode_mark;
+
+	AuDebugOn(data_type != FSNOTIFY_EVENT_INODE);
+
+	err = 0;
+	/* if FS_UNMOUNT happens, there must be another bug */
+	AuDebugOn(mask & FS_UNMOUNT);
+	if (mask & (FS_IN_IGNORED | FS_UNMOUNT))
+		goto out;
+
+	h_dir = dir;
+	h_inode = NULL;
+#ifdef AuDbgHnotify
+	au_debug_on();
+	if (1 || h_child_qstr.len != sizeof(AUFS_XINO_FNAME) - 1
+	    || strncmp(h_child_qstr.name, AUFS_XINO_FNAME, h_child_qstr.len)) {
+		AuDbg("i%lu, mask 0x%x %s, hcname %.*s, hi%lu\n",
+		      h_dir->i_ino, mask, au_hfsn_name(mask),
+		      AuLNPair(&h_child_qstr), h_inode ? h_inode->i_ino : 0);
+		/* WARN_ON(1); */
+	}
+	au_debug_off();
+#endif
+
+	inode_mark = fsnotify_iter_inode_mark(iter_info);
+	AuDebugOn(!inode_mark);
+	hnotify = container_of(inode_mark, struct au_hnotify, hn_mark);
+	err = au_hnotify(h_dir, hnotify, mask, file_name, h_inode);
+
+out:
+	return err;
+}
+
+static struct fsnotify_ops au_hfsn_ops = {
+	.handle_event		= au_hfsn_handle_event,
+	.free_group_priv	= au_hfsn_free_group,
+	.free_mark		= au_hfsn_free_mark
+};
+
+/* ---------------------------------------------------------------------- */
+
+static void au_hfsn_fin_br(struct au_branch *br)
+{
+	struct au_br_hfsnotify *hfsn;
+
+	hfsn = br->br_hfsn;
+	if (hfsn) {
+		lockdep_off();
+		fsnotify_put_group(hfsn->hfsn_group);
+		lockdep_on();
+	}
+}
+
+static int au_hfsn_init_br(struct au_branch *br, int perm)
+{
+	int err;
+	struct fsnotify_group *group;
+	struct au_br_hfsnotify *hfsn;
+
+	err = 0;
+	br->br_hfsn = NULL;
+	if (!au_br_hnotifyable(perm))
+		goto out;
+
+	err = -ENOMEM;
+	hfsn = kmalloc(sizeof(*hfsn), GFP_NOFS);
+	if (unlikely(!hfsn))
+		goto out;
+
+	err = 0;
+	group = fsnotify_alloc_group(&au_hfsn_ops);
+	if (IS_ERR(group)) {
+		err = PTR_ERR(group);
+		pr_err("fsnotify_alloc_group() failed, %d\n", err);
+		goto out_hfsn;
+	}
+
+	group->private = hfsn;
+	hfsn->hfsn_group = group;
+	br->br_hfsn = hfsn;
+	goto out; /* success */
+
+out_hfsn:
+	au_kfree_try_rcu(hfsn);
+out:
+	return err;
+}
+
+static int au_hfsn_reset_br(unsigned int udba, struct au_branch *br, int perm)
+{
+	int err;
+
+	err = 0;
+	if (!br->br_hfsn)
+		err = au_hfsn_init_br(br, perm);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void au_hfsn_fin(void)
+{
+	AuDbg("au_hfsn_ifree %lld\n", (long long)atomic64_read(&au_hfsn_ifree));
+	wait_event(au_hfsn_wq, !atomic64_read(&au_hfsn_ifree));
+}
+
+const struct au_hnotify_op au_hnotify_op = {
+	.ctl		= au_hfsn_ctl,
+	.alloc		= au_hfsn_alloc,
+	.free		= au_hfsn_free,
+
+	.fin		= au_hfsn_fin,
+
+	.reset_br	= au_hfsn_reset_br,
+	.fin_br		= au_hfsn_fin_br,
+	.init_br	= au_hfsn_init_br
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/hfsplus.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/hfsplus.c
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2010-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * special support for filesystems which acquires an inode mutex
+ * at final closing a file, eg, hfsplus.
+ *
+ * This trick is very simple and stupid, just to open the file before really
+ * necessary open to tell hfsplus that this is not the final closing.
+ * The caller should call au_h_open_pre() after acquiring the inode mutex,
+ * and au_h_open_post() after releasing it.
+ */
+
+#include "aufs.h"
+
+struct file *au_h_open_pre(struct dentry *dentry, aufs_bindex_t bindex,
+			   int force_wr)
+{
+	struct file *h_file;
+	struct dentry *h_dentry;
+
+	h_dentry = au_h_dptr(dentry, bindex);
+	AuDebugOn(!h_dentry);
+	AuDebugOn(d_is_negative(h_dentry));
+
+	h_file = NULL;
+	if (au_test_hfsplus(h_dentry->d_sb)
+	    && d_is_reg(h_dentry))
+		h_file = au_h_open(dentry, bindex,
+				   O_RDONLY | O_NOATIME | O_LARGEFILE,
+				   /*file*/NULL, force_wr);
+	return h_file;
+}
+
+void au_h_open_post(struct dentry *dentry, aufs_bindex_t bindex,
+		    struct file *h_file)
+{
+	struct au_branch *br;
+
+	if (h_file) {
+		fput(h_file);
+		br = au_sbr(dentry->d_sb, bindex);
+		au_lcnt_dec(&br->br_nfiles);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/hnotify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/hnotify.c
@@ -0,0 +1,715 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * abstraction to notify the direct changes on lower directories
+ */
+
+/* #include <linux/iversion.h> */
+#include "aufs.h"
+
+int au_hn_alloc(struct au_hinode *hinode, struct inode *inode)
+{
+	int err;
+	struct au_hnotify *hn;
+
+	err = -ENOMEM;
+	hn = au_cache_alloc_hnotify();
+	if (hn) {
+		hn->hn_aufs_inode = inode;
+		hinode->hi_notify = hn;
+		err = au_hnotify_op.alloc(hinode);
+		AuTraceErr(err);
+		if (unlikely(err)) {
+			hinode->hi_notify = NULL;
+			au_cache_free_hnotify(hn);
+			/*
+			 * The upper dir was removed by udba, but the same named
+			 * dir left. In this case, aufs assigns a new inode
+			 * number and set the monitor again.
+			 * For the lower dir, the old monitor is still left.
+			 */
+			if (err == -EEXIST)
+				err = 0;
+		}
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+void au_hn_free(struct au_hinode *hinode)
+{
+	struct au_hnotify *hn;
+
+	hn = hinode->hi_notify;
+	if (hn) {
+		hinode->hi_notify = NULL;
+		if (au_hnotify_op.free(hinode, hn))
+			au_cache_free_hnotify(hn);
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_hn_ctl(struct au_hinode *hinode, int do_set)
+{
+	if (hinode->hi_notify)
+		au_hnotify_op.ctl(hinode, do_set);
+}
+
+void au_hn_reset(struct inode *inode, unsigned int flags)
+{
+	aufs_bindex_t bindex, bbot;
+	struct inode *hi;
+	struct dentry *iwhdentry;
+
+	bbot = au_ibbot(inode);
+	for (bindex = au_ibtop(inode); bindex <= bbot; bindex++) {
+		hi = au_h_iptr(inode, bindex);
+		if (!hi)
+			continue;
+
+		/* inode_lock_nested(hi, AuLsc_I_CHILD); */
+		iwhdentry = au_hi_wh(inode, bindex);
+		if (iwhdentry)
+			dget(iwhdentry);
+		au_igrab(hi);
+		au_set_h_iptr(inode, bindex, NULL, 0);
+		au_set_h_iptr(inode, bindex, au_igrab(hi),
+			      flags & ~AuHi_XINO);
+		iput(hi);
+		dput(iwhdentry);
+		/* inode_unlock(hi); */
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int hn_xino(struct inode *inode, struct inode *h_inode)
+{
+	int err;
+	aufs_bindex_t bindex, bbot, bfound, btop;
+	struct inode *h_i;
+
+	err = 0;
+	if (unlikely(inode->i_ino == AUFS_ROOT_INO)) {
+		pr_warn("branch root dir was changed\n");
+		goto out;
+	}
+
+	bfound = -1;
+	bbot = au_ibbot(inode);
+	btop = au_ibtop(inode);
+#if 0 /* reserved for future use */
+	if (bindex == bbot) {
+		/* keep this ino in rename case */
+		goto out;
+	}
+#endif
+	for (bindex = btop; bindex <= bbot; bindex++)
+		if (au_h_iptr(inode, bindex) == h_inode) {
+			bfound = bindex;
+			break;
+		}
+	if (bfound < 0)
+		goto out;
+
+	for (bindex = btop; bindex <= bbot; bindex++) {
+		h_i = au_h_iptr(inode, bindex);
+		if (!h_i)
+			continue;
+
+		err = au_xino_write(inode->i_sb, bindex, h_i->i_ino, /*ino*/0);
+		/* ignore this error */
+		/* bad action? */
+	}
+
+	/* children inode number will be broken */
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int hn_gen_tree(struct dentry *dentry)
+{
+	int err, i, j, ndentry;
+	struct au_dcsub_pages dpages;
+	struct au_dpage *dpage;
+	struct dentry **dentries;
+
+	err = au_dpages_init(&dpages, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+	err = au_dcsub_pages(&dpages, dentry, NULL, NULL);
+	if (unlikely(err))
+		goto out_dpages;
+
+	for (i = 0; i < dpages.ndpage; i++) {
+		dpage = dpages.dpages + i;
+		dentries = dpage->dentries;
+		ndentry = dpage->ndentry;
+		for (j = 0; j < ndentry; j++) {
+			struct dentry *d;
+
+			d = dentries[j];
+			if (IS_ROOT(d))
+				continue;
+
+			au_digen_dec(d);
+			if (d_really_is_positive(d))
+				/* todo: reset children xino?
+				   cached children only? */
+				au_iigen_dec(d_inode(d));
+		}
+	}
+
+out_dpages:
+	au_dpages_free(&dpages);
+out:
+	return err;
+}
+
+/*
+ * return 0 if processed.
+ */
+static int hn_gen_by_inode(char *name, unsigned int nlen, struct inode *inode,
+			   const unsigned int isdir)
+{
+	int err;
+	struct dentry *d;
+	struct qstr *dname;
+
+	err = 1;
+	if (unlikely(inode->i_ino == AUFS_ROOT_INO)) {
+		pr_warn("branch root dir was changed\n");
+		err = 0;
+		goto out;
+	}
+
+	if (!isdir) {
+		AuDebugOn(!name);
+		au_iigen_dec(inode);
+		spin_lock(&inode->i_lock);
+		hlist_for_each_entry(d, &inode->i_dentry, d_u.d_alias) {
+			spin_lock(&d->d_lock);
+			dname = &d->d_name;
+			if (dname->len != nlen
+			    && memcmp(dname->name, name, nlen)) {
+				spin_unlock(&d->d_lock);
+				continue;
+			}
+			err = 0;
+			au_digen_dec(d);
+			spin_unlock(&d->d_lock);
+			break;
+		}
+		spin_unlock(&inode->i_lock);
+	} else {
+		au_fset_si(au_sbi(inode->i_sb), FAILED_REFRESH_DIR);
+		d = d_find_any_alias(inode);
+		if (!d) {
+			au_iigen_dec(inode);
+			goto out;
+		}
+
+		spin_lock(&d->d_lock);
+		dname = &d->d_name;
+		if (dname->len == nlen && !memcmp(dname->name, name, nlen)) {
+			spin_unlock(&d->d_lock);
+			err = hn_gen_tree(d);
+			spin_lock(&d->d_lock);
+		}
+		spin_unlock(&d->d_lock);
+		dput(d);
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int hn_gen_by_name(struct dentry *dentry, const unsigned int isdir)
+{
+	int err;
+
+	if (IS_ROOT(dentry)) {
+		pr_warn("branch root dir was changed\n");
+		return 0;
+	}
+
+	err = 0;
+	if (!isdir) {
+		au_digen_dec(dentry);
+		if (d_really_is_positive(dentry))
+			au_iigen_dec(d_inode(dentry));
+	} else {
+		au_fset_si(au_sbi(dentry->d_sb), FAILED_REFRESH_DIR);
+		if (d_really_is_positive(dentry))
+			err = hn_gen_tree(dentry);
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* hnotify job flags */
+#define AuHnJob_XINO0		1
+#define AuHnJob_GEN		(1 << 1)
+#define AuHnJob_DIRENT		(1 << 2)
+#define AuHnJob_ISDIR		(1 << 3)
+#define AuHnJob_TRYXINO0	(1 << 4)
+#define AuHnJob_MNTPNT		(1 << 5)
+#define au_ftest_hnjob(flags, name)	((flags) & AuHnJob_##name)
+#define au_fset_hnjob(flags, name) \
+	do { (flags) |= AuHnJob_##name; } while (0)
+#define au_fclr_hnjob(flags, name) \
+	do { (flags) &= ~AuHnJob_##name; } while (0)
+
+enum {
+	AuHn_CHILD,
+	AuHn_PARENT,
+	AuHnLast
+};
+
+struct au_hnotify_args {
+	struct inode *h_dir, *dir, *h_child_inode;
+	u32 mask;
+	unsigned int flags[AuHnLast];
+	unsigned int h_child_nlen;
+	char h_child_name[];
+};
+
+struct hn_job_args {
+	unsigned int flags;
+	struct inode *inode, *h_inode, *dir, *h_dir;
+	struct dentry *dentry;
+	char *h_name;
+	int h_nlen;
+};
+
+static int hn_job(struct hn_job_args *a)
+{
+	const unsigned int isdir = au_ftest_hnjob(a->flags, ISDIR);
+	int e;
+
+	/* reset xino */
+	if (au_ftest_hnjob(a->flags, XINO0) && a->inode)
+		hn_xino(a->inode, a->h_inode); /* ignore this error */
+
+	if (au_ftest_hnjob(a->flags, TRYXINO0)
+	    && a->inode
+	    && a->h_inode) {
+		inode_lock_shared_nested(a->h_inode, AuLsc_I_CHILD);
+		if (!a->h_inode->i_nlink
+		    && !(a->h_inode->i_state & I_LINKABLE))
+			hn_xino(a->inode, a->h_inode); /* ignore this error */
+		inode_unlock_shared(a->h_inode);
+	}
+
+	/* make the generation obsolete */
+	if (au_ftest_hnjob(a->flags, GEN)) {
+		e = -1;
+		if (a->inode)
+			e = hn_gen_by_inode(a->h_name, a->h_nlen, a->inode,
+					      isdir);
+		if (e && a->dentry)
+			hn_gen_by_name(a->dentry, isdir);
+		/* ignore this error */
+	}
+
+	/* make dir entries obsolete */
+	if (au_ftest_hnjob(a->flags, DIRENT) && a->inode) {
+		struct au_vdir *vdir;
+
+		vdir = au_ivdir(a->inode);
+		if (vdir)
+			vdir->vd_jiffy = 0;
+		/* IMustLock(a->inode); */
+		/* inode_inc_iversion(a->inode); */
+	}
+
+	/* can do nothing but warn */
+	if (au_ftest_hnjob(a->flags, MNTPNT)
+	    && a->dentry
+	    && d_mountpoint(a->dentry))
+		pr_warn("mount-point %pd is removed or renamed\n", a->dentry);
+
+	return 0;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct dentry *lookup_wlock_by_name(char *name, unsigned int nlen,
+					   struct inode *dir)
+{
+	struct dentry *dentry, *d, *parent;
+	struct qstr *dname;
+
+	parent = d_find_any_alias(dir);
+	if (!parent)
+		return NULL;
+
+	dentry = NULL;
+	spin_lock(&parent->d_lock);
+	list_for_each_entry(d, &parent->d_subdirs, d_child) {
+		/* AuDbg("%pd\n", d); */
+		spin_lock_nested(&d->d_lock, DENTRY_D_LOCK_NESTED);
+		dname = &d->d_name;
+		if (dname->len != nlen || memcmp(dname->name, name, nlen))
+			goto cont_unlock;
+		if (au_di(d))
+			au_digen_dec(d);
+		else
+			goto cont_unlock;
+		if (au_dcount(d) > 0) {
+			dentry = dget_dlock(d);
+			spin_unlock(&d->d_lock);
+			break;
+		}
+
+cont_unlock:
+		spin_unlock(&d->d_lock);
+	}
+	spin_unlock(&parent->d_lock);
+	dput(parent);
+
+	if (dentry)
+		di_write_lock_child(dentry);
+
+	return dentry;
+}
+
+static struct inode *lookup_wlock_by_ino(struct super_block *sb,
+					 aufs_bindex_t bindex, ino_t h_ino)
+{
+	struct inode *inode;
+	ino_t ino;
+	int err;
+
+	inode = NULL;
+	err = au_xino_read(sb, bindex, h_ino, &ino);
+	if (!err && ino)
+		inode = ilookup(sb, ino);
+	if (!inode)
+		goto out;
+
+	if (unlikely(inode->i_ino == AUFS_ROOT_INO)) {
+		pr_warn("wrong root branch\n");
+		iput(inode);
+		inode = NULL;
+		goto out;
+	}
+
+	ii_write_lock_child(inode);
+
+out:
+	return inode;
+}
+
+static void au_hn_bh(void *_args)
+{
+	struct au_hnotify_args *a = _args;
+	struct super_block *sb;
+	aufs_bindex_t bindex, bbot, bfound;
+	unsigned char xino, try_iput;
+	int err;
+	struct inode *inode;
+	ino_t h_ino;
+	struct hn_job_args args;
+	struct dentry *dentry;
+	struct au_sbinfo *sbinfo;
+
+	AuDebugOn(!_args);
+	AuDebugOn(!a->h_dir);
+	AuDebugOn(!a->dir);
+	AuDebugOn(!a->mask);
+	AuDbg("mask 0x%x, i%lu, hi%lu, hci%lu\n",
+	      a->mask, a->dir->i_ino, a->h_dir->i_ino,
+	      a->h_child_inode ? a->h_child_inode->i_ino : 0);
+
+	inode = NULL;
+	dentry = NULL;
+	/*
+	 * do not lock a->dir->i_mutex here
+	 * because of d_revalidate() may cause a deadlock.
+	 */
+	sb = a->dir->i_sb;
+	AuDebugOn(!sb);
+	sbinfo = au_sbi(sb);
+	AuDebugOn(!sbinfo);
+	si_write_lock(sb, AuLock_NOPLMW);
+
+	if (au_opt_test(sbinfo->si_mntflags, DIRREN))
+		switch (a->mask & FS_EVENTS_POSS_ON_CHILD) {
+		case FS_MOVED_FROM:
+		case FS_MOVED_TO:
+			AuWarn1("DIRREN with UDBA may not work correctly "
+				"for the direct rename(2)\n");
+		}
+
+	ii_read_lock_parent(a->dir);
+	bfound = -1;
+	bbot = au_ibbot(a->dir);
+	for (bindex = au_ibtop(a->dir); bindex <= bbot; bindex++)
+		if (au_h_iptr(a->dir, bindex) == a->h_dir) {
+			bfound = bindex;
+			break;
+		}
+	ii_read_unlock(a->dir);
+	if (unlikely(bfound < 0))
+		goto out;
+
+	xino = !!au_opt_test(au_mntflags(sb), XINO);
+	h_ino = 0;
+	if (a->h_child_inode)
+		h_ino = a->h_child_inode->i_ino;
+
+	if (a->h_child_nlen
+	    && (au_ftest_hnjob(a->flags[AuHn_CHILD], GEN)
+		|| au_ftest_hnjob(a->flags[AuHn_CHILD], MNTPNT)))
+		dentry = lookup_wlock_by_name(a->h_child_name, a->h_child_nlen,
+					      a->dir);
+	try_iput = 0;
+	if (dentry && d_really_is_positive(dentry))
+		inode = d_inode(dentry);
+	if (xino && !inode && h_ino
+	    && (au_ftest_hnjob(a->flags[AuHn_CHILD], XINO0)
+		|| au_ftest_hnjob(a->flags[AuHn_CHILD], TRYXINO0)
+		|| au_ftest_hnjob(a->flags[AuHn_CHILD], GEN))) {
+		inode = lookup_wlock_by_ino(sb, bfound, h_ino);
+		try_iput = 1;
+	}
+
+	args.flags = a->flags[AuHn_CHILD];
+	args.dentry = dentry;
+	args.inode = inode;
+	args.h_inode = a->h_child_inode;
+	args.dir = a->dir;
+	args.h_dir = a->h_dir;
+	args.h_name = a->h_child_name;
+	args.h_nlen = a->h_child_nlen;
+	err = hn_job(&args);
+	if (dentry) {
+		if (au_di(dentry))
+			di_write_unlock(dentry);
+		dput(dentry);
+	}
+	if (inode && try_iput) {
+		ii_write_unlock(inode);
+		iput(inode);
+	}
+
+	ii_write_lock_parent(a->dir);
+	args.flags = a->flags[AuHn_PARENT];
+	args.dentry = NULL;
+	args.inode = a->dir;
+	args.h_inode = a->h_dir;
+	args.dir = NULL;
+	args.h_dir = NULL;
+	args.h_name = NULL;
+	args.h_nlen = 0;
+	err = hn_job(&args);
+	ii_write_unlock(a->dir);
+
+out:
+	iput(a->h_child_inode);
+	iput(a->h_dir);
+	iput(a->dir);
+	si_write_unlock(sb);
+	au_nwt_done(&sbinfo->si_nowait);
+	au_kfree_rcu(a);
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_hnotify(struct inode *h_dir, struct au_hnotify *hnotify, u32 mask,
+	       const struct qstr *h_child_qstr, struct inode *h_child_inode)
+{
+	int err, len;
+	unsigned int flags[AuHnLast], f;
+	unsigned char isdir, isroot, wh;
+	struct inode *dir;
+	struct au_hnotify_args *args;
+	char *p, *h_child_name;
+
+	err = 0;
+	AuDebugOn(!hnotify || !hnotify->hn_aufs_inode);
+	dir = igrab(hnotify->hn_aufs_inode);
+	if (!dir)
+		goto out;
+
+	isroot = (dir->i_ino == AUFS_ROOT_INO);
+	wh = 0;
+	h_child_name = (void *)h_child_qstr->name;
+	len = h_child_qstr->len;
+	if (h_child_name) {
+		if (len > AUFS_WH_PFX_LEN
+		    && !memcmp(h_child_name, AUFS_WH_PFX, AUFS_WH_PFX_LEN)) {
+			h_child_name += AUFS_WH_PFX_LEN;
+			len -= AUFS_WH_PFX_LEN;
+			wh = 1;
+		}
+	}
+
+	isdir = 0;
+	if (h_child_inode)
+		isdir = !!S_ISDIR(h_child_inode->i_mode);
+	flags[AuHn_PARENT] = AuHnJob_ISDIR;
+	flags[AuHn_CHILD] = 0;
+	if (isdir)
+		flags[AuHn_CHILD] = AuHnJob_ISDIR;
+	au_fset_hnjob(flags[AuHn_PARENT], DIRENT);
+	au_fset_hnjob(flags[AuHn_CHILD], GEN);
+	switch (mask & ALL_FSNOTIFY_DIRENT_EVENTS) {
+	case FS_MOVED_FROM:
+	case FS_MOVED_TO:
+		au_fset_hnjob(flags[AuHn_CHILD], XINO0);
+		au_fset_hnjob(flags[AuHn_CHILD], MNTPNT);
+		fallthrough;
+	case FS_CREATE:
+		AuDebugOn(!h_child_name);
+		break;
+
+	case FS_DELETE:
+		/*
+		 * aufs never be able to get this child inode.
+		 * revalidation should be in d_revalidate()
+		 * by checking i_nlink, i_generation or d_unhashed().
+		 */
+		AuDebugOn(!h_child_name);
+		au_fset_hnjob(flags[AuHn_CHILD], TRYXINO0);
+		au_fset_hnjob(flags[AuHn_CHILD], MNTPNT);
+		break;
+
+	default:
+		AuDebugOn(1);
+	}
+
+	if (wh)
+		h_child_inode = NULL;
+
+	err = -ENOMEM;
+	/* iput() and kfree() will be called in au_hnotify() */
+	args = kmalloc(sizeof(*args) + len + 1, GFP_NOFS);
+	if (unlikely(!args)) {
+		AuErr1("no memory\n");
+		iput(dir);
+		goto out;
+	}
+	args->flags[AuHn_PARENT] = flags[AuHn_PARENT];
+	args->flags[AuHn_CHILD] = flags[AuHn_CHILD];
+	args->mask = mask;
+	args->dir = dir;
+	args->h_dir = igrab(h_dir);
+	if (h_child_inode)
+		h_child_inode = igrab(h_child_inode); /* can be NULL */
+	args->h_child_inode = h_child_inode;
+	args->h_child_nlen = len;
+	if (len) {
+		p = (void *)args;
+		p += sizeof(*args);
+		memcpy(p, h_child_name, len);
+		p[len] = 0;
+	}
+
+	/* NFS fires the event for silly-renamed one from kworker */
+	f = 0;
+	if (!dir->i_nlink
+	    || (au_test_nfs(h_dir->i_sb) && (mask & FS_DELETE)))
+		f = AuWkq_NEST;
+	err = au_wkq_nowait(au_hn_bh, args, dir->i_sb, f);
+	if (unlikely(err)) {
+		pr_err("wkq %d\n", err);
+		iput(args->h_child_inode);
+		iput(args->h_dir);
+		iput(args->dir);
+		au_kfree_rcu(args);
+	}
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_hnotify_reset_br(unsigned int udba, struct au_branch *br, int perm)
+{
+	int err;
+
+	AuDebugOn(!(udba & AuOptMask_UDBA));
+
+	err = 0;
+	if (au_hnotify_op.reset_br)
+		err = au_hnotify_op.reset_br(udba, br, perm);
+
+	return err;
+}
+
+int au_hnotify_init_br(struct au_branch *br, int perm)
+{
+	int err;
+
+	err = 0;
+	if (au_hnotify_op.init_br)
+		err = au_hnotify_op.init_br(br, perm);
+
+	return err;
+}
+
+void au_hnotify_fin_br(struct au_branch *br)
+{
+	if (au_hnotify_op.fin_br)
+		au_hnotify_op.fin_br(br);
+}
+
+static void au_hn_destroy_cache(void)
+{
+	kmem_cache_destroy(au_cache[AuCache_HNOTIFY]);
+	au_cache[AuCache_HNOTIFY] = NULL;
+}
+
+int __init au_hnotify_init(void)
+{
+	int err;
+
+	err = -ENOMEM;
+	au_cache[AuCache_HNOTIFY] = AuCache(au_hnotify);
+	if (au_cache[AuCache_HNOTIFY]) {
+		err = 0;
+		if (au_hnotify_op.init)
+			err = au_hnotify_op.init();
+		if (unlikely(err))
+			au_hn_destroy_cache();
+	}
+	AuTraceErr(err);
+	return err;
+}
+
+void au_hnotify_fin(void)
+{
+	if (au_hnotify_op.fin)
+		au_hnotify_op.fin();
+
+	/* cf. au_cache_fin() */
+	if (au_cache[AuCache_HNOTIFY])
+		au_hn_destroy_cache();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/i_op.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/i_op.c
@@ -0,0 +1,1513 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode operations (except add/del/rename)
+ */
+
+#include <linux/device_cgroup.h>
+#include <linux/fs_stack.h>
+#include <linux/iversion.h>
+#include <linux/namei.h>
+#include <linux/security.h>
+#include "aufs.h"
+
+static int h_permission(struct inode *h_inode, int mask,
+			struct path *h_path, int brperm)
+{
+	int err;
+	const unsigned char write_mask = !!(mask & (MAY_WRITE | MAY_APPEND));
+	struct user_namespace *h_userns;
+
+	err = -EPERM;
+	if (write_mask && IS_IMMUTABLE(h_inode))
+		goto out;
+
+	err = -EACCES;
+	if (((mask & MAY_EXEC)
+	     && S_ISREG(h_inode->i_mode)
+	     && (path_noexec(h_path)
+		 || !(h_inode->i_mode & 0111))))
+		goto out;
+
+	/*
+	 * - skip the lower fs test in the case of write to ro branch.
+	 * - nfs dir permission write check is optimized, but a policy for
+	 *   link/rename requires a real check.
+	 * - nfs always sets SB_POSIXACL regardless its mount option 'noacl.'
+	 *   in this case, generic_permission() returns -EOPNOTSUPP.
+	 */
+	h_userns = mnt_user_ns(h_path->mnt);
+	if ((write_mask && !au_br_writable(brperm))
+	    || (au_test_nfs(h_inode->i_sb) && S_ISDIR(h_inode->i_mode)
+		&& write_mask && !(mask & MAY_READ))
+	    || !h_inode->i_op->permission) {
+		/* AuLabel(generic_permission); */
+		/* AuDbg("get_acl %ps\n", h_inode->i_op->get_acl); */
+		err = generic_permission(h_userns, h_inode, mask);
+		if (err == -EOPNOTSUPP && au_test_nfs_noacl(h_inode))
+			err = h_inode->i_op->permission(h_userns, h_inode,
+							mask);
+		AuTraceErr(err);
+	} else {
+		/* AuLabel(h_inode->permission); */
+		err = h_inode->i_op->permission(h_userns, h_inode, mask);
+		AuTraceErr(err);
+	}
+
+	if (!err)
+		err = devcgroup_inode_permission(h_inode, mask);
+	if (!err)
+		err = security_inode_permission(h_inode, mask);
+
+out:
+	return err;
+}
+
+static int aufs_permission(struct user_namespace *userns, struct inode *inode,
+			   int mask)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	const unsigned char isdir = !!S_ISDIR(inode->i_mode),
+		write_mask = !!(mask & (MAY_WRITE | MAY_APPEND));
+	struct inode *h_inode;
+	struct super_block *sb;
+	struct au_branch *br;
+
+	/* todo: support rcu-walk? */
+	if (mask & MAY_NOT_BLOCK)
+		return -ECHILD;
+
+	sb = inode->i_sb;
+	si_read_lock(sb, AuLock_FLUSH);
+	ii_read_lock_child(inode);
+#if 0 /* reserved for future use */
+	/*
+	 * This test may be rather 'too much' since the test is essentially done
+	 * in the aufs_lookup().  Theoretically it is possible that the inode
+	 * generation doesn't match to the superblock's here.  But it isn't a
+	 * big deal I suppose.
+	 */
+	err = au_iigen_test(inode, au_sigen(sb));
+	if (unlikely(err))
+		goto out;
+#endif
+
+	if (!isdir
+	    || write_mask
+	    || au_opt_test(au_mntflags(sb), DIRPERM1)) {
+		err = au_busy_or_stale();
+		h_inode = au_h_iptr(inode, au_ibtop(inode));
+		if (unlikely(!h_inode
+			     || (h_inode->i_mode & S_IFMT)
+			     != (inode->i_mode & S_IFMT)))
+			goto out;
+
+		err = 0;
+		bindex = au_ibtop(inode);
+		br = au_sbr(sb, bindex);
+		err = h_permission(h_inode, mask, &br->br_path, br->br_perm);
+		if (write_mask
+		    && !err
+		    && !special_file(h_inode->i_mode)) {
+			/* test whether the upper writable branch exists */
+			err = -EROFS;
+			for (; bindex >= 0; bindex--)
+				if (!au_br_rdonly(au_sbr(sb, bindex))) {
+					err = 0;
+					break;
+				}
+		}
+		goto out;
+	}
+
+	/* non-write to dir */
+	err = 0;
+	bbot = au_ibbot(inode);
+	for (bindex = au_ibtop(inode); !err && bindex <= bbot; bindex++) {
+		h_inode = au_h_iptr(inode, bindex);
+		if (h_inode) {
+			err = au_busy_or_stale();
+			if (unlikely(!S_ISDIR(h_inode->i_mode)))
+				break;
+
+			br = au_sbr(sb, bindex);
+			err = h_permission(h_inode, mask, &br->br_path,
+					   br->br_perm);
+		}
+	}
+
+out:
+	ii_read_unlock(inode);
+	si_read_unlock(sb);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct dentry *aufs_lookup(struct inode *dir, struct dentry *dentry,
+				  unsigned int flags)
+{
+	struct dentry *ret, *parent;
+	struct inode *inode;
+	struct super_block *sb;
+	int err, npositive;
+
+	IMustLock(dir);
+
+	/* todo: support rcu-walk? */
+	ret = ERR_PTR(-ECHILD);
+	if (flags & LOOKUP_RCU)
+		goto out;
+
+	ret = ERR_PTR(-ENAMETOOLONG);
+	if (unlikely(dentry->d_name.len > AUFS_MAX_NAMELEN))
+		goto out;
+
+	sb = dir->i_sb;
+	err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+	ret = ERR_PTR(err);
+	if (unlikely(err))
+		goto out;
+
+	err = au_di_init(dentry);
+	ret = ERR_PTR(err);
+	if (unlikely(err))
+		goto out_si;
+
+	inode = NULL;
+	npositive = 0; /* suppress a warning */
+	parent = dentry->d_parent; /* dir inode is locked */
+	di_read_lock_parent(parent, AuLock_IR);
+	err = au_alive_dir(parent);
+	if (!err)
+		err = au_digen_test(parent, au_sigen(sb));
+	if (!err) {
+		/* regardless LOOKUP_CREATE, always ALLOW_NEG */
+		npositive = au_lkup_dentry(dentry, au_dbtop(parent),
+					   AuLkup_ALLOW_NEG);
+		err = npositive;
+	}
+	di_read_unlock(parent, AuLock_IR);
+	ret = ERR_PTR(err);
+	if (unlikely(err < 0))
+		goto out_unlock;
+
+	if (npositive) {
+		inode = au_new_inode(dentry, /*must_new*/0);
+		if (IS_ERR(inode)) {
+			ret = (void *)inode;
+			inode = NULL;
+			goto out_unlock;
+		}
+	}
+
+	if (inode)
+		atomic_inc(&inode->i_count);
+	ret = d_splice_alias(inode, dentry);
+#if 0 /* reserved for future use */
+	if (unlikely(d_need_lookup(dentry))) {
+		spin_lock(&dentry->d_lock);
+		dentry->d_flags &= ~DCACHE_NEED_LOOKUP;
+		spin_unlock(&dentry->d_lock);
+	} else
+#endif
+	if (inode) {
+		if (!IS_ERR(ret)) {
+			iput(inode);
+			if (ret && ret != dentry)
+				ii_write_unlock(inode);
+		} else {
+			ii_write_unlock(inode);
+			iput(inode);
+			inode = NULL;
+		}
+	}
+
+out_unlock:
+	di_write_unlock(dentry);
+out_si:
+	si_read_unlock(sb);
+out:
+	return ret;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * very dirty and complicated aufs ->atomic_open().
+ * aufs_atomic_open()
+ * + au_aopen_or_create()
+ *   + add_simple()
+ *     + vfsub_atomic_open()
+ *       + branch fs ->atomic_open()
+ *	   may call the actual 'open' for h_file
+ *       + inc br_nfiles only if opened
+ * + au_aopen_no_open() or au_aopen_do_open()
+ *
+ * au_aopen_do_open()
+ * + finish_open()
+ *   + au_do_aopen()
+ *     + au_do_open() the body of all 'open'
+ *       + au_do_open_nondir()
+ *	   set the passed h_file
+ *
+ * au_aopen_no_open()
+ * + finish_no_open()
+ */
+
+struct aopen_node {
+	struct hlist_bl_node hblist;
+	struct file *file, *h_file;
+};
+
+static int au_do_aopen(struct inode *inode, struct file *file)
+{
+	struct hlist_bl_head *aopen;
+	struct hlist_bl_node *pos;
+	struct aopen_node *node;
+	struct au_do_open_args args = {
+		.aopen	= 1,
+		.open	= au_do_open_nondir
+	};
+
+	aopen = &au_sbi(inode->i_sb)->si_aopen;
+	hlist_bl_lock(aopen);
+	hlist_bl_for_each_entry(node, pos, aopen, hblist)
+		if (node->file == file) {
+			args.h_file = node->h_file;
+			break;
+		}
+	hlist_bl_unlock(aopen);
+	/* AuDebugOn(!args.h_file); */
+
+	return au_do_open(file, &args);
+}
+
+static int au_aopen_do_open(struct file *file, struct dentry *dentry,
+			    struct aopen_node *aopen_node)
+{
+	int err;
+	struct hlist_bl_head *aopen;
+
+	AuLabel(here);
+	aopen = &au_sbi(dentry->d_sb)->si_aopen;
+	au_hbl_add(&aopen_node->hblist, aopen);
+	err = finish_open(file, dentry, au_do_aopen);
+	au_hbl_del(&aopen_node->hblist, aopen);
+	/* AuDbgFile(file); */
+	AuDbg("%pd%s%s\n", dentry,
+	      (file->f_mode & FMODE_CREATED) ? " created" : "",
+	      (file->f_mode & FMODE_OPENED) ? " opened" : "");
+
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_aopen_no_open(struct file *file, struct dentry *dentry)
+{
+	int err;
+
+	AuLabel(here);
+	dget(dentry);
+	err = finish_no_open(file, dentry);
+
+	AuTraceErr(err);
+	return err;
+}
+
+static int aufs_atomic_open(struct inode *dir, struct dentry *dentry,
+			    struct file *file, unsigned int open_flag,
+			    umode_t create_mode)
+{
+	int err, did_open;
+	unsigned int lkup_flags;
+	aufs_bindex_t bindex;
+	struct super_block *sb;
+	struct dentry *parent, *d;
+	struct vfsub_aopen_args args = {
+		.open_flag	= open_flag,
+		.create_mode	= create_mode
+	};
+	struct aopen_node aopen_node = {
+		.file	= file
+	};
+
+	IMustLock(dir);
+	AuDbg("open_flag 0%o\n", open_flag);
+	AuDbgDentry(dentry);
+
+	err = 0;
+	if (!au_di(dentry)) {
+		lkup_flags = LOOKUP_OPEN;
+		if (open_flag & O_CREAT)
+			lkup_flags |= LOOKUP_CREATE;
+		d = aufs_lookup(dir, dentry, lkup_flags);
+		if (IS_ERR(d)) {
+			err = PTR_ERR(d);
+			AuTraceErr(err);
+			goto out;
+		} else if (d) {
+			/*
+			 * obsoleted dentry found.
+			 * another error will be returned later.
+			 */
+			d_drop(d);
+			AuDbgDentry(d);
+			dput(d);
+		}
+		AuDbgDentry(dentry);
+	}
+
+	if (d_is_positive(dentry)
+	    || d_unhashed(dentry)
+	    || d_unlinked(dentry)
+	    || !(open_flag & O_CREAT)) {
+		err = au_aopen_no_open(file, dentry);
+		goto out; /* success */
+	}
+
+	err = aufs_read_lock(dentry, AuLock_DW | AuLock_FLUSH | AuLock_GEN);
+	if (unlikely(err))
+		goto out;
+
+	sb = dentry->d_sb;
+	parent = dentry->d_parent;	/* dir is locked */
+	di_write_lock_parent(parent);
+	err = au_lkup_dentry(dentry, /*btop*/0, AuLkup_ALLOW_NEG);
+	if (unlikely(err < 0))
+		goto out_parent;
+
+	AuDbgDentry(dentry);
+	if (d_is_positive(dentry)) {
+		err = au_aopen_no_open(file, dentry);
+		goto out_parent; /* success */
+	}
+
+	args.file = alloc_empty_file(file->f_flags, current_cred());
+	err = PTR_ERR(args.file);
+	if (IS_ERR(args.file))
+		goto out_parent;
+
+	bindex = au_dbtop(dentry);
+	err = au_aopen_or_create(dir, dentry, &args);
+	AuTraceErr(err);
+	AuDbgFile(args.file);
+	file->f_mode = args.file->f_mode & ~FMODE_OPENED;
+	did_open = !!(args.file->f_mode & FMODE_OPENED);
+	if (!did_open) {
+		fput(args.file);
+		args.file = NULL;
+	}
+	di_write_unlock(parent);
+	di_write_unlock(dentry);
+	if (unlikely(err < 0)) {
+		if (args.file)
+			fput(args.file);
+		goto out_sb;
+	}
+
+	if (!did_open)
+		err = au_aopen_no_open(file, dentry);
+	else {
+		aopen_node.h_file = args.file;
+		err = au_aopen_do_open(file, dentry, &aopen_node);
+	}
+	if (unlikely(err < 0)) {
+		if (args.file)
+			fput(args.file);
+		if (did_open)
+			au_lcnt_dec(&args.br->br_nfiles);
+	}
+	goto out_sb; /* success */
+
+out_parent:
+	di_write_unlock(parent);
+	di_write_unlock(dentry);
+out_sb:
+	si_read_unlock(sb);
+out:
+	AuTraceErr(err);
+	AuDbgFile(file);
+	return err;
+}
+
+
+/* ---------------------------------------------------------------------- */
+
+static int au_wr_dir_cpup(struct dentry *dentry, struct dentry *parent,
+			  const unsigned char add_entry, aufs_bindex_t bcpup,
+			  aufs_bindex_t btop)
+{
+	int err;
+	struct dentry *h_parent;
+	struct inode *h_dir;
+
+	if (add_entry)
+		IMustLock(d_inode(parent));
+	else
+		di_write_lock_parent(parent);
+
+	err = 0;
+	if (!au_h_dptr(parent, bcpup)) {
+		if (btop > bcpup)
+			err = au_cpup_dirs(dentry, bcpup);
+		else if (btop < bcpup)
+			err = au_cpdown_dirs(dentry, bcpup);
+		else
+			BUG();
+	}
+	if (!err && add_entry && !au_ftest_wrdir(add_entry, TMPFILE)) {
+		h_parent = au_h_dptr(parent, bcpup);
+		h_dir = d_inode(h_parent);
+		inode_lock_shared_nested(h_dir, AuLsc_I_PARENT);
+		err = au_lkup_neg(dentry, bcpup, /*wh*/0);
+		/* todo: no unlock here */
+		inode_unlock_shared(h_dir);
+
+		AuDbg("bcpup %d\n", bcpup);
+		if (!err) {
+			if (d_really_is_negative(dentry))
+				au_set_h_dptr(dentry, btop, NULL);
+			au_update_dbrange(dentry, /*do_put_zero*/0);
+		}
+	}
+
+	if (!add_entry)
+		di_write_unlock(parent);
+	if (!err)
+		err = bcpup; /* success */
+
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * decide the branch and the parent dir where we will create a new entry.
+ * returns new bindex or an error.
+ * copyup the parent dir if needed.
+ */
+int au_wr_dir(struct dentry *dentry, struct dentry *src_dentry,
+	      struct au_wr_dir_args *args)
+{
+	int err;
+	unsigned int flags;
+	aufs_bindex_t bcpup, btop, src_btop;
+	const unsigned char add_entry
+		= au_ftest_wrdir(args->flags, ADD_ENTRY)
+		| au_ftest_wrdir(args->flags, TMPFILE);
+	struct super_block *sb;
+	struct dentry *parent;
+	struct au_sbinfo *sbinfo;
+
+	sb = dentry->d_sb;
+	sbinfo = au_sbi(sb);
+	parent = dget_parent(dentry);
+	btop = au_dbtop(dentry);
+	bcpup = btop;
+	if (args->force_btgt < 0) {
+		if (src_dentry) {
+			src_btop = au_dbtop(src_dentry);
+			if (src_btop < btop)
+				bcpup = src_btop;
+		} else if (add_entry) {
+			flags = 0;
+			if (au_ftest_wrdir(args->flags, ISDIR))
+				au_fset_wbr(flags, DIR);
+			err = AuWbrCreate(sbinfo, dentry, flags);
+			bcpup = err;
+		}
+
+		if (bcpup < 0 || au_test_ro(sb, bcpup, d_inode(dentry))) {
+			if (add_entry)
+				err = AuWbrCopyup(sbinfo, dentry);
+			else {
+				if (!IS_ROOT(dentry)) {
+					di_read_lock_parent(parent, !AuLock_IR);
+					err = AuWbrCopyup(sbinfo, dentry);
+					di_read_unlock(parent, !AuLock_IR);
+				} else
+					err = AuWbrCopyup(sbinfo, dentry);
+			}
+			bcpup = err;
+			if (unlikely(err < 0))
+				goto out;
+		}
+	} else {
+		bcpup = args->force_btgt;
+		AuDebugOn(au_test_ro(sb, bcpup, d_inode(dentry)));
+	}
+
+	AuDbg("btop %d, bcpup %d\n", btop, bcpup);
+	err = bcpup;
+	if (bcpup == btop)
+		goto out; /* success */
+
+	/* copyup the new parent into the branch we process */
+	err = au_wr_dir_cpup(dentry, parent, add_entry, bcpup, btop);
+	if (err >= 0) {
+		if (d_really_is_negative(dentry)) {
+			au_set_h_dptr(dentry, btop, NULL);
+			au_set_dbtop(dentry, bcpup);
+			au_set_dbbot(dentry, bcpup);
+		}
+		AuDebugOn(add_entry
+			  && !au_ftest_wrdir(args->flags, TMPFILE)
+			  && !au_h_dptr(dentry, bcpup));
+	}
+
+out:
+	dput(parent);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_pin_hdir_unlock(struct au_pin *p)
+{
+	if (p->hdir)
+		au_hn_inode_unlock(p->hdir);
+}
+
+int au_pin_hdir_lock(struct au_pin *p)
+{
+	int err;
+
+	err = 0;
+	if (!p->hdir)
+		goto out;
+
+	/* even if an error happens later, keep this lock */
+	au_hn_inode_lock_nested(p->hdir, p->lsc_hi);
+
+	err = -EBUSY;
+	if (unlikely(p->hdir->hi_inode != d_inode(p->h_parent)))
+		goto out;
+
+	err = 0;
+	if (p->h_dentry)
+		err = au_h_verify(p->h_dentry, p->udba, p->hdir->hi_inode,
+				  p->h_parent, p->br);
+
+out:
+	return err;
+}
+
+int au_pin_hdir_relock(struct au_pin *p)
+{
+	int err, i;
+	struct inode *h_i;
+	struct dentry *h_d[] = {
+		p->h_dentry,
+		p->h_parent
+	};
+
+	err = au_pin_hdir_lock(p);
+	if (unlikely(err))
+		goto out;
+
+	for (i = 0; !err && i < sizeof(h_d)/sizeof(*h_d); i++) {
+		if (!h_d[i])
+			continue;
+		if (d_is_positive(h_d[i])) {
+			h_i = d_inode(h_d[i]);
+			err = !h_i->i_nlink;
+		}
+	}
+
+out:
+	return err;
+}
+
+static void au_pin_hdir_set_owner(struct au_pin *p, struct task_struct *task)
+{
+	atomic_long_set(&p->hdir->hi_inode->i_rwsem.owner, (long)task);
+}
+
+void au_pin_hdir_acquire_nest(struct au_pin *p)
+{
+	if (p->hdir) {
+		rwsem_acquire_nest(&p->hdir->hi_inode->i_rwsem.dep_map,
+				   p->lsc_hi, 0, NULL, _RET_IP_);
+		au_pin_hdir_set_owner(p, current);
+	}
+}
+
+void au_pin_hdir_release(struct au_pin *p)
+{
+	if (p->hdir) {
+		au_pin_hdir_set_owner(p, p->task);
+		rwsem_release(&p->hdir->hi_inode->i_rwsem.dep_map, _RET_IP_);
+	}
+}
+
+struct dentry *au_pinned_h_parent(struct au_pin *pin)
+{
+	if (pin && pin->parent)
+		return au_h_dptr(pin->parent, pin->bindex);
+	return NULL;
+}
+
+void au_unpin(struct au_pin *p)
+{
+	if (p->hdir)
+		au_pin_hdir_unlock(p);
+	if (p->h_mnt && au_ftest_pin(p->flags, MNT_WRITE))
+		vfsub_mnt_drop_write(p->h_mnt);
+	if (!p->hdir)
+		return;
+
+	if (!au_ftest_pin(p->flags, DI_LOCKED))
+		di_read_unlock(p->parent, AuLock_IR);
+	iput(p->hdir->hi_inode);
+	dput(p->parent);
+	p->parent = NULL;
+	p->hdir = NULL;
+	p->h_mnt = NULL;
+	/* do not clear p->task */
+}
+
+int au_do_pin(struct au_pin *p)
+{
+	int err;
+	struct super_block *sb;
+	struct inode *h_dir;
+
+	err = 0;
+	sb = p->dentry->d_sb;
+	p->br = au_sbr(sb, p->bindex);
+	if (IS_ROOT(p->dentry)) {
+		if (au_ftest_pin(p->flags, MNT_WRITE)) {
+			p->h_mnt = au_br_mnt(p->br);
+			err = vfsub_mnt_want_write(p->h_mnt);
+			if (unlikely(err)) {
+				au_fclr_pin(p->flags, MNT_WRITE);
+				goto out_err;
+			}
+		}
+		goto out;
+	}
+
+	p->h_dentry = NULL;
+	if (p->bindex <= au_dbbot(p->dentry))
+		p->h_dentry = au_h_dptr(p->dentry, p->bindex);
+
+	p->parent = dget_parent(p->dentry);
+	if (!au_ftest_pin(p->flags, DI_LOCKED))
+		di_read_lock(p->parent, AuLock_IR, p->lsc_di);
+
+	h_dir = NULL;
+	p->h_parent = au_h_dptr(p->parent, p->bindex);
+	p->hdir = au_hi(d_inode(p->parent), p->bindex);
+	if (p->hdir)
+		h_dir = p->hdir->hi_inode;
+
+	/*
+	 * udba case, or
+	 * if DI_LOCKED is not set, then p->parent may be different
+	 * and h_parent can be NULL.
+	 */
+	if (unlikely(!p->hdir || !h_dir || !p->h_parent)) {
+		err = -EBUSY;
+		if (!au_ftest_pin(p->flags, DI_LOCKED))
+			di_read_unlock(p->parent, AuLock_IR);
+		dput(p->parent);
+		p->parent = NULL;
+		goto out_err;
+	}
+
+	if (au_ftest_pin(p->flags, MNT_WRITE)) {
+		p->h_mnt = au_br_mnt(p->br);
+		err = vfsub_mnt_want_write(p->h_mnt);
+		if (unlikely(err)) {
+			au_fclr_pin(p->flags, MNT_WRITE);
+			if (!au_ftest_pin(p->flags, DI_LOCKED))
+				di_read_unlock(p->parent, AuLock_IR);
+			dput(p->parent);
+			p->parent = NULL;
+			goto out_err;
+		}
+	}
+
+	au_igrab(h_dir);
+	err = au_pin_hdir_lock(p);
+	if (!err)
+		goto out; /* success */
+
+	au_unpin(p);
+
+out_err:
+	pr_err("err %d\n", err);
+	err = au_busy_or_stale();
+out:
+	return err;
+}
+
+void au_pin_init(struct au_pin *p, struct dentry *dentry,
+		 aufs_bindex_t bindex, int lsc_di, int lsc_hi,
+		 unsigned int udba, unsigned char flags)
+{
+	p->dentry = dentry;
+	p->udba = udba;
+	p->lsc_di = lsc_di;
+	p->lsc_hi = lsc_hi;
+	p->flags = flags;
+	p->bindex = bindex;
+
+	p->parent = NULL;
+	p->hdir = NULL;
+	p->h_mnt = NULL;
+
+	p->h_dentry = NULL;
+	p->h_parent = NULL;
+	p->br = NULL;
+	p->task = current;
+}
+
+int au_pin(struct au_pin *pin, struct dentry *dentry, aufs_bindex_t bindex,
+	   unsigned int udba, unsigned char flags)
+{
+	au_pin_init(pin, dentry, bindex, AuLsc_DI_PARENT, AuLsc_I_PARENT2,
+		    udba, flags);
+	return au_do_pin(pin);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * ->setattr() and ->getattr() are called in various cases.
+ * chmod, stat: dentry is revalidated.
+ * fchmod, fstat: file and dentry are not revalidated, additionally they may be
+ *		  unhashed.
+ * for ->setattr(), ia->ia_file is passed from ftruncate only.
+ */
+/* todo: consolidate with do_refresh() and simple_reval_dpath() */
+int au_reval_for_attr(struct dentry *dentry, unsigned int sigen)
+{
+	int err;
+	struct dentry *parent;
+
+	err = 0;
+	if (au_digen_test(dentry, sigen)) {
+		parent = dget_parent(dentry);
+		di_read_lock_parent(parent, AuLock_IR);
+		err = au_refresh_dentry(dentry, parent);
+		di_read_unlock(parent, AuLock_IR);
+		dput(parent);
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+int au_pin_and_icpup(struct dentry *dentry, struct iattr *ia,
+		     struct au_icpup_args *a)
+{
+	int err;
+	loff_t sz;
+	aufs_bindex_t btop, ibtop;
+	struct dentry *hi_wh, *parent;
+	struct inode *inode;
+	struct au_wr_dir_args wr_dir_args = {
+		.force_btgt	= -1,
+		.flags		= 0
+	};
+
+	if (d_is_dir(dentry))
+		au_fset_wrdir(wr_dir_args.flags, ISDIR);
+	/* plink or hi_wh() case */
+	btop = au_dbtop(dentry);
+	inode = d_inode(dentry);
+	ibtop = au_ibtop(inode);
+	if (btop != ibtop && !au_test_ro(inode->i_sb, ibtop, inode))
+		wr_dir_args.force_btgt = ibtop;
+	err = au_wr_dir(dentry, /*src_dentry*/NULL, &wr_dir_args);
+	if (unlikely(err < 0))
+		goto out;
+	a->btgt = err;
+	if (err != btop)
+		au_fset_icpup(a->flags, DID_CPUP);
+
+	err = 0;
+	a->pin_flags = AuPin_MNT_WRITE;
+	parent = NULL;
+	if (!IS_ROOT(dentry)) {
+		au_fset_pin(a->pin_flags, DI_LOCKED);
+		parent = dget_parent(dentry);
+		di_write_lock_parent(parent);
+	}
+
+	err = au_pin(&a->pin, dentry, a->btgt, a->udba, a->pin_flags);
+	if (unlikely(err))
+		goto out_parent;
+
+	sz = -1;
+	a->h_path.dentry = au_h_dptr(dentry, btop);
+	a->h_inode = d_inode(a->h_path.dentry);
+	if (ia && (ia->ia_valid & ATTR_SIZE)) {
+		inode_lock_shared_nested(a->h_inode, AuLsc_I_CHILD);
+		if (ia->ia_size < i_size_read(a->h_inode))
+			sz = ia->ia_size;
+		inode_unlock_shared(a->h_inode);
+	}
+
+	hi_wh = NULL;
+	if (au_ftest_icpup(a->flags, DID_CPUP) && d_unlinked(dentry)) {
+		hi_wh = au_hi_wh(inode, a->btgt);
+		if (!hi_wh) {
+			struct au_cp_generic cpg = {
+				.dentry	= dentry,
+				.bdst	= a->btgt,
+				.bsrc	= -1,
+				.len	= sz,
+				.pin	= &a->pin
+			};
+			err = au_sio_cpup_wh(&cpg, /*file*/NULL);
+			if (unlikely(err))
+				goto out_unlock;
+			hi_wh = au_hi_wh(inode, a->btgt);
+			/* todo: revalidate hi_wh? */
+		}
+	}
+
+	if (parent) {
+		au_pin_set_parent_lflag(&a->pin, /*lflag*/0);
+		di_downgrade_lock(parent, AuLock_IR);
+		dput(parent);
+		parent = NULL;
+	}
+	if (!au_ftest_icpup(a->flags, DID_CPUP))
+		goto out; /* success */
+
+	if (!d_unhashed(dentry)) {
+		struct au_cp_generic cpg = {
+			.dentry	= dentry,
+			.bdst	= a->btgt,
+			.bsrc	= btop,
+			.len	= sz,
+			.pin	= &a->pin,
+			.flags	= AuCpup_DTIME | AuCpup_HOPEN
+		};
+		err = au_sio_cpup_simple(&cpg);
+		if (!err)
+			a->h_path.dentry = au_h_dptr(dentry, a->btgt);
+	} else if (!hi_wh)
+		a->h_path.dentry = au_h_dptr(dentry, a->btgt);
+	else
+		a->h_path.dentry = hi_wh; /* do not dget here */
+
+out_unlock:
+	a->h_inode = d_inode(a->h_path.dentry);
+	if (!err)
+		goto out; /* success */
+	au_unpin(&a->pin);
+out_parent:
+	if (parent) {
+		di_write_unlock(parent);
+		dput(parent);
+	}
+out:
+	if (!err)
+		inode_lock_nested(a->h_inode, AuLsc_I_CHILD);
+	return err;
+}
+
+static int aufs_setattr(struct user_namespace *userns, struct dentry *dentry,
+			struct iattr *ia)
+{
+	int err;
+	struct inode *inode, *delegated;
+	struct super_block *sb;
+	struct file *file;
+	struct au_icpup_args *a;
+	struct user_namespace *h_userns;
+
+	inode = d_inode(dentry);
+	IMustLock(inode);
+
+	err = setattr_prepare(userns, dentry, ia);
+	if (unlikely(err))
+		goto out;
+
+	err = -ENOMEM;
+	a = kzalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	if (ia->ia_valid & (ATTR_KILL_SUID | ATTR_KILL_SGID))
+		ia->ia_valid &= ~ATTR_MODE;
+
+	file = NULL;
+	sb = dentry->d_sb;
+	err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+	if (unlikely(err))
+		goto out_kfree;
+
+	if (ia->ia_valid & ATTR_FILE) {
+		/* currently ftruncate(2) only */
+		AuDebugOn(!d_is_reg(dentry));
+		file = ia->ia_file;
+		err = au_reval_and_lock_fdi(file, au_reopen_nondir, /*wlock*/1,
+					    /*fi_lsc*/0);
+		if (unlikely(err))
+			goto out_si;
+		ia->ia_file = au_hf_top(file);
+		a->udba = AuOpt_UDBA_NONE;
+	} else {
+		/* fchmod() doesn't pass ia_file */
+		a->udba = au_opt_udba(sb);
+		di_write_lock_child(dentry);
+		/* no d_unlinked(), to set UDBA_NONE for root */
+		if (d_unhashed(dentry))
+			a->udba = AuOpt_UDBA_NONE;
+		if (a->udba != AuOpt_UDBA_NONE) {
+			AuDebugOn(IS_ROOT(dentry));
+			err = au_reval_for_attr(dentry, au_sigen(sb));
+			if (unlikely(err))
+				goto out_dentry;
+		}
+	}
+
+	err = au_pin_and_icpup(dentry, ia, a);
+	if (unlikely(err < 0))
+		goto out_dentry;
+	if (au_ftest_icpup(a->flags, DID_CPUP)) {
+		ia->ia_file = NULL;
+		ia->ia_valid &= ~ATTR_FILE;
+	}
+
+	a->h_path.mnt = au_sbr_mnt(sb, a->btgt);
+	if ((ia->ia_valid & (ATTR_MODE | ATTR_CTIME))
+	    == (ATTR_MODE | ATTR_CTIME)) {
+		err = security_path_chmod(&a->h_path, ia->ia_mode);
+		if (unlikely(err))
+			goto out_unlock;
+	} else if ((ia->ia_valid & (ATTR_UID | ATTR_GID))
+		   && (ia->ia_valid & ATTR_CTIME)) {
+		err = security_path_chown(&a->h_path, ia->ia_uid, ia->ia_gid);
+		if (unlikely(err))
+			goto out_unlock;
+	}
+
+	if (ia->ia_valid & ATTR_SIZE) {
+		struct file *f;
+
+		if (ia->ia_size < i_size_read(inode))
+			/* unmap only */
+			truncate_setsize(inode, ia->ia_size);
+
+		f = NULL;
+		if (ia->ia_valid & ATTR_FILE)
+			f = ia->ia_file;
+		inode_unlock(a->h_inode);
+		err = vfsub_trunc(&a->h_path, ia->ia_size, ia->ia_valid, f);
+		inode_lock_nested(a->h_inode, AuLsc_I_CHILD);
+	} else {
+		delegated = NULL;
+		while (1) {
+			err = vfsub_notify_change(&a->h_path, ia, &delegated);
+			if (delegated) {
+				err = break_deleg_wait(&delegated);
+				if (!err)
+					continue;
+			}
+			break;
+		}
+	}
+	/*
+	 * regardless aufs 'acl' option setting.
+	 * why don't all acl-aware fs call this func from their ->setattr()?
+	 */
+	if (!err && (ia->ia_valid & ATTR_MODE)) {
+		h_userns = mnt_user_ns(a->h_path.mnt);
+		err = vfsub_acl_chmod(h_userns, a->h_inode, ia->ia_mode);
+	}
+	if (!err)
+		au_cpup_attr_changeable(inode);
+
+out_unlock:
+	inode_unlock(a->h_inode);
+	au_unpin(&a->pin);
+	if (unlikely(err))
+		au_update_dbtop(dentry);
+out_dentry:
+	di_write_unlock(dentry);
+	if (file) {
+		fi_write_unlock(file);
+		ia->ia_file = file;
+		ia->ia_valid |= ATTR_FILE;
+	}
+out_si:
+	si_read_unlock(sb);
+out_kfree:
+	au_kfree_rcu(a);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+#if IS_ENABLED(CONFIG_AUFS_XATTR) || IS_ENABLED(CONFIG_FS_POSIX_ACL)
+static int au_h_path_to_set_attr(struct dentry *dentry,
+				 struct au_icpup_args *a, struct path *h_path)
+{
+	int err;
+	struct super_block *sb;
+
+	sb = dentry->d_sb;
+	a->udba = au_opt_udba(sb);
+	/* no d_unlinked(), to set UDBA_NONE for root */
+	if (d_unhashed(dentry))
+		a->udba = AuOpt_UDBA_NONE;
+	if (a->udba != AuOpt_UDBA_NONE) {
+		AuDebugOn(IS_ROOT(dentry));
+		err = au_reval_for_attr(dentry, au_sigen(sb));
+		if (unlikely(err))
+			goto out;
+	}
+	err = au_pin_and_icpup(dentry, /*ia*/NULL, a);
+	if (unlikely(err < 0))
+		goto out;
+
+	h_path->dentry = a->h_path.dentry;
+	h_path->mnt = au_sbr_mnt(sb, a->btgt);
+
+out:
+	return err;
+}
+
+ssize_t au_sxattr(struct dentry *dentry, struct inode *inode,
+		  struct au_sxattr *arg)
+{
+	int err;
+	struct path h_path;
+	struct super_block *sb;
+	struct au_icpup_args *a;
+	struct inode *h_inode;
+	struct user_namespace *h_userns;
+
+	IMustLock(inode);
+
+	err = -ENOMEM;
+	a = kzalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	sb = dentry->d_sb;
+	err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+	if (unlikely(err))
+		goto out_kfree;
+
+	h_path.dentry = NULL;	/* silence gcc */
+	di_write_lock_child(dentry);
+	err = au_h_path_to_set_attr(dentry, a, &h_path);
+	if (unlikely(err))
+		goto out_di;
+	h_userns = mnt_user_ns(h_path.mnt);
+
+	inode_unlock(a->h_inode);
+	switch (arg->type) {
+	case AU_XATTR_SET:
+		AuDebugOn(d_is_negative(h_path.dentry));
+		err = vfsub_setxattr(h_userns, h_path.dentry,
+				     arg->u.set.name, arg->u.set.value,
+				     arg->u.set.size, arg->u.set.flags);
+		break;
+	case AU_ACL_SET:
+		err = -EOPNOTSUPP;
+		h_inode = d_inode(h_path.dentry);
+		if (h_inode->i_op->set_acl) {
+			/* this will call posix_acl_update_mode */
+			err = h_inode->i_op->set_acl(h_userns, h_inode,
+						     arg->u.acl_set.acl,
+						     arg->u.acl_set.type);
+		}
+		break;
+	}
+	if (!err)
+		au_cpup_attr_timesizes(inode);
+
+	au_unpin(&a->pin);
+	if (unlikely(err))
+		au_update_dbtop(dentry);
+
+out_di:
+	di_write_unlock(dentry);
+	si_read_unlock(sb);
+out_kfree:
+	au_kfree_rcu(a);
+out:
+	AuTraceErr(err);
+	return err;
+}
+#endif
+
+static void au_refresh_iattr(struct inode *inode, struct kstat *st,
+			     unsigned int nlink)
+{
+	unsigned int n;
+
+	inode->i_mode = st->mode;
+	/* don't i_[ug]id_write() here */
+	inode->i_uid = st->uid;
+	inode->i_gid = st->gid;
+	inode->i_atime = st->atime;
+	inode->i_mtime = st->mtime;
+	inode->i_ctime = st->ctime;
+
+	au_cpup_attr_nlink(inode, /*force*/0);
+	if (S_ISDIR(inode->i_mode)) {
+		n = inode->i_nlink;
+		n -= nlink;
+		n += st->nlink;
+		smp_mb(); /* for i_nlink */
+		/* 0 can happen */
+		set_nlink(inode, n);
+	}
+
+	spin_lock(&inode->i_lock);
+	inode->i_blocks = st->blocks;
+	i_size_write(inode, st->size);
+	spin_unlock(&inode->i_lock);
+}
+
+/*
+ * common routine for aufs_getattr() and au_getxattr().
+ * returns zero or negative (an error).
+ * @dentry will be read-locked in success.
+ */
+int au_h_path_getattr(struct dentry *dentry, struct inode *inode, int force,
+		      struct path *h_path, int locked)
+{
+	int err;
+	unsigned int mnt_flags, sigen;
+	unsigned char udba_none;
+	aufs_bindex_t bindex;
+	struct super_block *sb, *h_sb;
+
+	h_path->mnt = NULL;
+	h_path->dentry = NULL;
+
+	err = 0;
+	sb = dentry->d_sb;
+	mnt_flags = au_mntflags(sb);
+	udba_none = !!au_opt_test(mnt_flags, UDBA_NONE);
+
+	if (unlikely(locked))
+		goto body; /* skip locking dinfo */
+
+	/* support fstat(2) */
+	if (!d_unlinked(dentry) && !udba_none) {
+		sigen = au_sigen(sb);
+		err = au_digen_test(dentry, sigen);
+		if (!err) {
+			di_read_lock_child(dentry, AuLock_IR);
+			err = au_dbrange_test(dentry);
+			if (unlikely(err)) {
+				di_read_unlock(dentry, AuLock_IR);
+				goto out;
+			}
+		} else {
+			AuDebugOn(IS_ROOT(dentry));
+			di_write_lock_child(dentry);
+			err = au_dbrange_test(dentry);
+			if (!err)
+				err = au_reval_for_attr(dentry, sigen);
+			if (!err)
+				di_downgrade_lock(dentry, AuLock_IR);
+			else {
+				di_write_unlock(dentry);
+				goto out;
+			}
+		}
+	} else
+		di_read_lock_child(dentry, AuLock_IR);
+
+body:
+	if (!inode) {
+		inode = d_inode(dentry);
+		if (unlikely(!inode))
+			goto out;
+	}
+	bindex = au_ibtop(inode);
+	h_path->mnt = au_sbr_mnt(sb, bindex);
+	h_sb = h_path->mnt->mnt_sb;
+	if (!force
+	    && !au_test_fs_bad_iattr(h_sb)
+	    && udba_none)
+		goto out; /* success */
+
+	if (au_dbtop(dentry) == bindex)
+		h_path->dentry = au_h_dptr(dentry, bindex);
+	else if (au_opt_test(mnt_flags, PLINK) && au_plink_test(inode)) {
+		h_path->dentry = au_plink_lkup(inode, bindex);
+		if (IS_ERR(h_path->dentry))
+			/* pretending success */
+			h_path->dentry = NULL;
+		else
+			dput(h_path->dentry);
+	}
+
+out:
+	return err;
+}
+
+static int aufs_getattr(struct user_namespace *userns, const struct path *path,
+			struct kstat *st, u32 request, unsigned int query)
+{
+	int err;
+	unsigned char positive;
+	struct path h_path;
+	struct dentry *dentry;
+	struct inode *inode;
+	struct super_block *sb;
+
+	dentry = path->dentry;
+	inode = d_inode(dentry);
+	sb = dentry->d_sb;
+	err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+	if (unlikely(err))
+		goto out;
+	err = au_h_path_getattr(dentry, /*inode*/NULL, /*force*/0, &h_path,
+				/*locked*/0);
+	if (unlikely(err))
+		goto out_si;
+	if (unlikely(!h_path.dentry))
+		/* illegally overlapped or something */
+		goto out_fill; /* pretending success */
+
+	positive = d_is_positive(h_path.dentry);
+	if (positive)
+		/* no vfsub version */
+		err = vfs_getattr(&h_path, st, request, query);
+	if (!err) {
+		if (positive)
+			au_refresh_iattr(inode, st,
+					 d_inode(h_path.dentry)->i_nlink);
+		goto out_fill; /* success */
+	}
+	AuTraceErr(err);
+	goto out_di;
+
+out_fill:
+	generic_fillattr(userns, inode, st);
+out_di:
+	di_read_unlock(dentry, AuLock_IR);
+out_si:
+	si_read_unlock(sb);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static const char *aufs_get_link(struct dentry *dentry, struct inode *inode,
+				 struct delayed_call *done)
+{
+	const char *ret;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	int err;
+	aufs_bindex_t bindex;
+
+	ret = NULL; /* suppress a warning */
+	err = -ECHILD;
+	if (!dentry)
+		goto out;
+
+	err = aufs_read_lock(dentry, AuLock_IR | AuLock_GEN);
+	if (unlikely(err))
+		goto out;
+
+	err = au_d_hashed_positive(dentry);
+	if (unlikely(err))
+		goto out_unlock;
+
+	err = -EINVAL;
+	inode = d_inode(dentry);
+	bindex = au_ibtop(inode);
+	h_inode = au_h_iptr(inode, bindex);
+	if (unlikely(!h_inode->i_op->get_link))
+		goto out_unlock;
+
+	err = -EBUSY;
+	h_dentry = NULL;
+	if (au_dbtop(dentry) <= bindex) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (h_dentry)
+			dget(h_dentry);
+	}
+	if (!h_dentry) {
+		h_dentry = d_find_any_alias(h_inode);
+		if (IS_ERR(h_dentry)) {
+			err = PTR_ERR(h_dentry);
+			goto out_unlock;
+		}
+	}
+	if (unlikely(!h_dentry))
+		goto out_unlock;
+
+	err = 0;
+	AuDbg("%ps\n", h_inode->i_op->get_link);
+	AuDbgDentry(h_dentry);
+	ret = vfs_get_link(h_dentry, done);
+	dput(h_dentry);
+	if (IS_ERR(ret))
+		err = PTR_ERR(ret);
+
+out_unlock:
+	aufs_read_unlock(dentry, AuLock_IR);
+out:
+	if (unlikely(err))
+		ret = ERR_PTR(err);
+	AuTraceErrPtr(ret);
+	return ret;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_is_special(struct inode *inode)
+{
+	return (inode->i_mode & (S_IFBLK | S_IFCHR | S_IFIFO | S_IFSOCK));
+}
+
+static int aufs_update_time(struct inode *inode, struct timespec64 *ts,
+			    int flags)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct super_block *sb;
+	struct inode *h_inode;
+	struct vfsmount *h_mnt;
+
+	sb = inode->i_sb;
+	WARN_ONCE((flags & S_ATIME) && !IS_NOATIME(inode),
+		  "unexpected s_flags 0x%lx", sb->s_flags);
+
+	/* mmap_sem might be acquired already, cf. aufs_mmap() */
+	lockdep_off();
+	si_read_lock(sb, AuLock_FLUSH);
+	ii_write_lock_child(inode);
+
+	err = 0;
+	bindex = au_ibtop(inode);
+	h_inode = au_h_iptr(inode, bindex);
+	if (!au_test_ro(sb, bindex, inode)) {
+		h_mnt = au_sbr_mnt(sb, bindex);
+		err = vfsub_mnt_want_write(h_mnt);
+		if (!err) {
+			err = vfsub_update_time(h_inode, ts, flags);
+			vfsub_mnt_drop_write(h_mnt);
+		}
+	} else if (au_is_special(h_inode)) {
+		/*
+		 * Never copy-up here.
+		 * These special files may already be opened and used for
+		 * communicating. If we copied it up, then the communication
+		 * would be corrupted.
+		 */
+		AuWarn1("timestamps for i%lu are ignored "
+			"since it is on readonly branch (hi%lu).\n",
+			inode->i_ino, h_inode->i_ino);
+	} else if (flags & ~S_ATIME) {
+		err = -EIO;
+		AuIOErr1("unexpected flags 0x%x\n", flags);
+		AuDebugOn(1);
+	}
+
+	if (!err)
+		au_cpup_attr_timesizes(inode);
+	ii_write_unlock(inode);
+	si_read_unlock(sb);
+	lockdep_on();
+
+	if (!err && (flags & S_VERSION))
+		inode_inc_iversion(inode);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* no getattr version will be set by module.c:aufs_init() */
+struct inode_operations aufs_iop_nogetattr[AuIop_Last],
+	aufs_iop[] = {
+	[AuIop_SYMLINK] = {
+		.permission	= aufs_permission,
+#ifdef CONFIG_FS_POSIX_ACL
+		.get_acl	= aufs_get_acl,
+		.set_acl	= aufs_set_acl, /* unsupport for symlink? */
+#endif
+
+		.setattr	= aufs_setattr,
+		.getattr	= aufs_getattr,
+
+#ifdef CONFIG_AUFS_XATTR
+		.listxattr	= aufs_listxattr,
+#endif
+
+		.get_link	= aufs_get_link,
+
+		/* .update_time	= aufs_update_time */
+	},
+	[AuIop_DIR] = {
+		.create		= aufs_create,
+		.lookup		= aufs_lookup,
+		.link		= aufs_link,
+		.unlink		= aufs_unlink,
+		.symlink	= aufs_symlink,
+		.mkdir		= aufs_mkdir,
+		.rmdir		= aufs_rmdir,
+		.mknod		= aufs_mknod,
+		.rename		= aufs_rename,
+
+		.permission	= aufs_permission,
+#ifdef CONFIG_FS_POSIX_ACL
+		.get_acl	= aufs_get_acl,
+		.set_acl	= aufs_set_acl,
+#endif
+
+		.setattr	= aufs_setattr,
+		.getattr	= aufs_getattr,
+
+#ifdef CONFIG_AUFS_XATTR
+		.listxattr	= aufs_listxattr,
+#endif
+
+		.update_time	= aufs_update_time,
+		.atomic_open	= aufs_atomic_open,
+		.tmpfile	= aufs_tmpfile
+	},
+	[AuIop_OTHER] = {
+		.permission	= aufs_permission,
+#ifdef CONFIG_FS_POSIX_ACL
+		.get_acl	= aufs_get_acl,
+		.set_acl	= aufs_set_acl,
+#endif
+
+		.setattr	= aufs_setattr,
+		.getattr	= aufs_getattr,
+
+#ifdef CONFIG_AUFS_XATTR
+		.listxattr	= aufs_listxattr,
+#endif
+
+		.update_time	= aufs_update_time
+	}
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/i_op_add.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/i_op_add.c
@@ -0,0 +1,941 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode operations (add entry)
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+/*
+ * final procedure of adding a new entry, except link(2).
+ * remove whiteout, instantiate, copyup the parent dir's times and size
+ * and update version.
+ * if it failed, re-create the removed whiteout.
+ */
+static int epilog(struct inode *dir, aufs_bindex_t bindex,
+		  struct dentry *wh_dentry, struct dentry *dentry)
+{
+	int err, rerr;
+	aufs_bindex_t bwh;
+	struct path h_path;
+	struct super_block *sb;
+	struct inode *inode, *h_dir;
+	struct dentry *wh;
+
+	bwh = -1;
+	sb = dir->i_sb;
+	if (wh_dentry) {
+		h_dir = d_inode(wh_dentry->d_parent); /* dir inode is locked */
+		IMustLock(h_dir);
+		AuDebugOn(au_h_iptr(dir, bindex) != h_dir);
+		bwh = au_dbwh(dentry);
+		h_path.dentry = wh_dentry;
+		h_path.mnt = au_sbr_mnt(sb, bindex);
+		err = au_wh_unlink_dentry(au_h_iptr(dir, bindex), &h_path,
+					  dentry);
+		if (unlikely(err))
+			goto out;
+	}
+
+	inode = au_new_inode(dentry, /*must_new*/1);
+	if (!IS_ERR(inode)) {
+		d_instantiate(dentry, inode);
+		dir = d_inode(dentry->d_parent); /* dir inode is locked */
+		IMustLock(dir);
+		au_dir_ts(dir, bindex);
+		inode_inc_iversion(dir);
+		au_fhsm_wrote(sb, bindex, /*force*/0);
+		return 0; /* success */
+	}
+
+	err = PTR_ERR(inode);
+	if (!wh_dentry)
+		goto out;
+
+	/* revert */
+	/* dir inode is locked */
+	wh = au_wh_create(dentry, bwh, wh_dentry->d_parent);
+	rerr = PTR_ERR(wh);
+	if (IS_ERR(wh)) {
+		AuIOErr("%pd reverting whiteout failed(%d, %d)\n",
+			dentry, err, rerr);
+		err = -EIO;
+	} else
+		dput(wh);
+
+out:
+	return err;
+}
+
+static int au_d_may_add(struct dentry *dentry)
+{
+	int err;
+
+	err = 0;
+	if (unlikely(d_unhashed(dentry)))
+		err = -ENOENT;
+	if (unlikely(d_really_is_positive(dentry)))
+		err = -EEXIST;
+	return err;
+}
+
+/*
+ * simple tests for the adding inode operations.
+ * following the checks in vfs, plus the parent-child relationship.
+ */
+int au_may_add(struct dentry *dentry, aufs_bindex_t bindex,
+	       struct dentry *h_parent, int isdir)
+{
+	int err;
+	umode_t h_mode;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+
+	err = -ENAMETOOLONG;
+	if (unlikely(dentry->d_name.len > AUFS_MAX_NAMELEN))
+		goto out;
+
+	h_dentry = au_h_dptr(dentry, bindex);
+	if (d_really_is_negative(dentry)) {
+		err = -EEXIST;
+		if (unlikely(d_is_positive(h_dentry)))
+			goto out;
+	} else {
+		/* rename(2) case */
+		err = -EIO;
+		if (unlikely(d_is_negative(h_dentry)))
+			goto out;
+		h_inode = d_inode(h_dentry);
+		if (unlikely(!h_inode->i_nlink))
+			goto out;
+
+		h_mode = h_inode->i_mode;
+		if (!isdir) {
+			err = -EISDIR;
+			if (unlikely(S_ISDIR(h_mode)))
+				goto out;
+		} else if (unlikely(!S_ISDIR(h_mode))) {
+			err = -ENOTDIR;
+			goto out;
+		}
+	}
+
+	err = 0;
+	/* expected parent dir is locked */
+	if (unlikely(h_parent != h_dentry->d_parent))
+		err = -EIO;
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * initial procedure of adding a new entry.
+ * prepare writable branch and the parent dir, lock it,
+ * and lookup whiteout for the new entry.
+ */
+static struct dentry*
+lock_hdir_lkup_wh(struct dentry *dentry, struct au_dtime *dt,
+		  struct dentry *src_dentry, struct au_pin *pin,
+		  struct au_wr_dir_args *wr_dir_args)
+{
+	struct dentry *wh_dentry, *h_parent;
+	struct super_block *sb;
+	struct au_branch *br;
+	int err;
+	unsigned int udba;
+	aufs_bindex_t bcpup;
+
+	AuDbg("%pd\n", dentry);
+
+	err = au_wr_dir(dentry, src_dentry, wr_dir_args);
+	bcpup = err;
+	wh_dentry = ERR_PTR(err);
+	if (unlikely(err < 0))
+		goto out;
+
+	sb = dentry->d_sb;
+	udba = au_opt_udba(sb);
+	err = au_pin(pin, dentry, bcpup, udba,
+		     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+	wh_dentry = ERR_PTR(err);
+	if (unlikely(err))
+		goto out;
+
+	h_parent = au_pinned_h_parent(pin);
+	if (udba != AuOpt_UDBA_NONE
+	    && au_dbtop(dentry) == bcpup)
+		err = au_may_add(dentry, bcpup, h_parent,
+				 au_ftest_wrdir(wr_dir_args->flags, ISDIR));
+	else if (unlikely(dentry->d_name.len > AUFS_MAX_NAMELEN))
+		err = -ENAMETOOLONG;
+	wh_dentry = ERR_PTR(err);
+	if (unlikely(err))
+		goto out_unpin;
+
+	br = au_sbr(sb, bcpup);
+	if (dt) {
+		struct path tmp = {
+			.dentry	= h_parent,
+			.mnt	= au_br_mnt(br)
+		};
+		au_dtime_store(dt, au_pinned_parent(pin), &tmp);
+	}
+
+	wh_dentry = NULL;
+	if (bcpup != au_dbwh(dentry))
+		goto out; /* success */
+
+	/*
+	 * ENAMETOOLONG here means that if we allowed create such name, then it
+	 * would not be able to removed in the future. So we don't allow such
+	 * name here and we don't handle ENAMETOOLONG differently here.
+	 */
+	wh_dentry = au_wh_lkup(h_parent, &dentry->d_name, br);
+
+out_unpin:
+	if (IS_ERR(wh_dentry))
+		au_unpin(pin);
+out:
+	return wh_dentry;
+}
+
+/* ---------------------------------------------------------------------- */
+
+enum { Mknod, Symlink, Creat };
+struct simple_arg {
+	int type;
+	union {
+		struct {
+			umode_t			mode;
+			bool			want_excl;
+			bool			try_aopen;
+			struct vfsub_aopen_args	*aopen;
+		} c;
+		struct {
+			const char *symname;
+		} s;
+		struct {
+			umode_t mode;
+			dev_t dev;
+		} m;
+	} u;
+};
+
+static int add_simple(struct inode *dir, struct dentry *dentry,
+		      struct simple_arg *arg)
+{
+	int err, rerr;
+	aufs_bindex_t btop;
+	unsigned char created;
+	const unsigned char try_aopen
+		= (arg->type == Creat && arg->u.c.try_aopen);
+	struct vfsub_aopen_args *aopen = arg->u.c.aopen;
+	struct dentry *wh_dentry, *parent;
+	struct inode *h_dir;
+	struct super_block *sb;
+	struct au_branch *br;
+	/* to reduce stack size */
+	struct {
+		struct au_dtime dt;
+		struct au_pin pin;
+		struct path h_path;
+		struct au_wr_dir_args wr_dir_args;
+	} *a;
+
+	AuDbg("%pd\n", dentry);
+	IMustLock(dir);
+
+	err = -ENOMEM;
+	a = kmalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+	a->wr_dir_args.force_btgt = -1;
+	a->wr_dir_args.flags = AuWrDir_ADD_ENTRY;
+
+	parent = dentry->d_parent; /* dir inode is locked */
+	if (!try_aopen) {
+		err = aufs_read_lock(dentry, AuLock_DW | AuLock_GEN);
+		if (unlikely(err))
+			goto out_free;
+	}
+	err = au_d_may_add(dentry);
+	if (unlikely(err))
+		goto out_unlock;
+	if (!try_aopen)
+		di_write_lock_parent(parent);
+	wh_dentry = lock_hdir_lkup_wh(dentry, &a->dt, /*src_dentry*/NULL,
+				      &a->pin, &a->wr_dir_args);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry))
+		goto out_parent;
+
+	btop = au_dbtop(dentry);
+	sb = dentry->d_sb;
+	br = au_sbr(sb, btop);
+	a->h_path.dentry = au_h_dptr(dentry, btop);
+	a->h_path.mnt = au_br_mnt(br);
+	h_dir = au_pinned_h_dir(&a->pin);
+	switch (arg->type) {
+	case Creat:
+		if (!try_aopen || !h_dir->i_op->atomic_open) {
+			err = vfsub_create(h_dir, &a->h_path, arg->u.c.mode,
+					   arg->u.c.want_excl);
+			created = !err;
+			if (!err && try_aopen)
+				aopen->file->f_mode |= FMODE_CREATED;
+		} else {
+			aopen->br = br;
+			err = vfsub_atomic_open(h_dir, a->h_path.dentry, aopen);
+			AuDbg("err %d\n", err);
+			AuDbgFile(aopen->file);
+			created = err >= 0
+				&& !!(aopen->file->f_mode & FMODE_CREATED);
+		}
+		break;
+	case Symlink:
+		err = vfsub_symlink(h_dir, &a->h_path, arg->u.s.symname);
+		created = !err;
+		break;
+	case Mknod:
+		err = vfsub_mknod(h_dir, &a->h_path, arg->u.m.mode,
+				  arg->u.m.dev);
+		created = !err;
+		break;
+	default:
+		BUG();
+	}
+	if (unlikely(err < 0))
+		goto out_unpin;
+
+	err = epilog(dir, btop, wh_dentry, dentry);
+	if (!err)
+		goto out_unpin; /* success */
+
+	/* revert */
+	if (created /* && d_is_positive(a->h_path.dentry) */) {
+		/* no delegation since it is just created */
+		rerr = vfsub_unlink(h_dir, &a->h_path, /*delegated*/NULL,
+				    /*force*/0);
+		if (rerr) {
+			AuIOErr("%pd revert failure(%d, %d)\n",
+				dentry, err, rerr);
+			err = -EIO;
+		}
+		au_dtime_revert(&a->dt);
+	}
+	if (try_aopen && h_dir->i_op->atomic_open
+	    && (aopen->file->f_mode & FMODE_OPENED))
+		/* aopen->file is still opened */
+		au_lcnt_dec(&aopen->br->br_nfiles);
+
+out_unpin:
+	au_unpin(&a->pin);
+	dput(wh_dentry);
+out_parent:
+	if (!try_aopen)
+		di_write_unlock(parent);
+out_unlock:
+	if (unlikely(err)) {
+		au_update_dbtop(dentry);
+		d_drop(dentry);
+	}
+	if (!try_aopen)
+		aufs_read_unlock(dentry, AuLock_DW);
+out_free:
+	au_kfree_rcu(a);
+out:
+	return err;
+}
+
+int aufs_mknod(struct user_namespace *userns, struct inode *dir,
+	       struct dentry *dentry, umode_t mode, dev_t dev)
+{
+	struct simple_arg arg = {
+		.type = Mknod,
+		.u.m = {
+			.mode	= mode,
+			.dev	= dev
+		}
+	};
+	return add_simple(dir, dentry, &arg);
+}
+
+int aufs_symlink(struct user_namespace *userns, struct inode *dir,
+		 struct dentry *dentry, const char *symname)
+{
+	struct simple_arg arg = {
+		.type = Symlink,
+		.u.s.symname = symname
+	};
+	return add_simple(dir, dentry, &arg);
+}
+
+int aufs_create(struct user_namespace *userns, struct inode *dir,
+		struct dentry *dentry, umode_t mode, bool want_excl)
+{
+	struct simple_arg arg = {
+		.type = Creat,
+		.u.c = {
+			.mode		= mode,
+			.want_excl	= want_excl
+		}
+	};
+	return add_simple(dir, dentry, &arg);
+}
+
+int au_aopen_or_create(struct inode *dir, struct dentry *dentry,
+		       struct vfsub_aopen_args *aopen_args)
+{
+	struct simple_arg arg = {
+		.type = Creat,
+		.u.c = {
+			.mode		= aopen_args->create_mode,
+			.want_excl	= aopen_args->open_flag & O_EXCL,
+			.try_aopen	= true,
+			.aopen		= aopen_args
+		}
+	};
+	return add_simple(dir, dentry, &arg);
+}
+
+int aufs_tmpfile(struct user_namespace *userns, struct inode *dir,
+		 struct dentry *dentry, umode_t mode)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct super_block *sb;
+	struct dentry *parent, *h_parent, *h_dentry;
+	struct inode *h_dir, *inode;
+	struct vfsmount *h_mnt;
+	struct user_namespace *h_userns;
+	struct au_wr_dir_args wr_dir_args = {
+		.force_btgt	= -1,
+		.flags		= AuWrDir_TMPFILE
+	};
+
+	/* copy-up may happen */
+	inode_lock(dir);
+
+	sb = dir->i_sb;
+	err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+	if (unlikely(err))
+		goto out;
+
+	err = au_di_init(dentry);
+	if (unlikely(err))
+		goto out_si;
+
+	err = -EBUSY;
+	parent = d_find_any_alias(dir);
+	AuDebugOn(!parent);
+	di_write_lock_parent(parent);
+	if (unlikely(d_inode(parent) != dir))
+		goto out_parent;
+
+	err = au_digen_test(parent, au_sigen(sb));
+	if (unlikely(err))
+		goto out_parent;
+
+	bindex = au_dbtop(parent);
+	au_set_dbtop(dentry, bindex);
+	au_set_dbbot(dentry, bindex);
+	err = au_wr_dir(dentry, /*src_dentry*/NULL, &wr_dir_args);
+	bindex = err;
+	if (unlikely(err < 0))
+		goto out_parent;
+
+	err = -EOPNOTSUPP;
+	h_dir = au_h_iptr(dir, bindex);
+	if (unlikely(!h_dir->i_op->tmpfile))
+		goto out_parent;
+
+	h_mnt = au_sbr_mnt(sb, bindex);
+	err = vfsub_mnt_want_write(h_mnt);
+	if (unlikely(err))
+		goto out_parent;
+
+	h_userns = mnt_user_ns(h_mnt);
+	h_parent = au_h_dptr(parent, bindex);
+	h_dentry = vfs_tmpfile(h_userns, h_parent, mode, /*open_flag*/0);
+	if (IS_ERR(h_dentry)) {
+		err = PTR_ERR(h_dentry);
+		goto out_mnt;
+	}
+
+	au_set_dbtop(dentry, bindex);
+	au_set_dbbot(dentry, bindex);
+	au_set_h_dptr(dentry, bindex, dget(h_dentry));
+	inode = au_new_inode(dentry, /*must_new*/1);
+	if (IS_ERR(inode)) {
+		err = PTR_ERR(inode);
+		au_set_h_dptr(dentry, bindex, NULL);
+		au_set_dbtop(dentry, -1);
+		au_set_dbbot(dentry, -1);
+	} else {
+		if (!inode->i_nlink)
+			set_nlink(inode, 1);
+		d_tmpfile(dentry, inode);
+		au_di(dentry)->di_tmpfile = 1;
+
+		/* update without i_mutex */
+		if (au_ibtop(dir) == au_dbtop(dentry))
+			au_cpup_attr_timesizes(dir);
+	}
+	dput(h_dentry);
+
+out_mnt:
+	vfsub_mnt_drop_write(h_mnt);
+out_parent:
+	di_write_unlock(parent);
+	dput(parent);
+	di_write_unlock(dentry);
+	if (unlikely(err)) {
+		au_di_fin(dentry);
+		dentry->d_fsdata = NULL;
+	}
+out_si:
+	si_read_unlock(sb);
+out:
+	inode_unlock(dir);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_link_args {
+	aufs_bindex_t bdst, bsrc;
+	struct au_pin pin;
+	struct path h_path;
+	struct dentry *src_parent, *parent;
+};
+
+static int au_cpup_before_link(struct dentry *src_dentry,
+			       struct au_link_args *a)
+{
+	int err;
+	struct dentry *h_src_dentry;
+	struct au_cp_generic cpg = {
+		.dentry	= src_dentry,
+		.bdst	= a->bdst,
+		.bsrc	= a->bsrc,
+		.len	= -1,
+		.pin	= &a->pin,
+		.flags	= AuCpup_DTIME | AuCpup_HOPEN /* | AuCpup_KEEPLINO */
+	};
+
+	di_read_lock_parent(a->src_parent, AuLock_IR);
+	err = au_test_and_cpup_dirs(src_dentry, a->bdst);
+	if (unlikely(err))
+		goto out;
+
+	h_src_dentry = au_h_dptr(src_dentry, a->bsrc);
+	err = au_pin(&a->pin, src_dentry, a->bdst,
+		     au_opt_udba(src_dentry->d_sb),
+		     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+	if (unlikely(err))
+		goto out;
+
+	err = au_sio_cpup_simple(&cpg);
+	au_unpin(&a->pin);
+
+out:
+	di_read_unlock(a->src_parent, AuLock_IR);
+	return err;
+}
+
+static int au_cpup_or_link(struct dentry *src_dentry, struct dentry *dentry,
+			   struct au_link_args *a)
+{
+	int err;
+	unsigned char plink;
+	aufs_bindex_t bbot;
+	struct dentry *h_src_dentry;
+	struct inode *h_inode, *inode, *delegated;
+	struct super_block *sb;
+	struct file *h_file;
+
+	plink = 0;
+	h_inode = NULL;
+	sb = src_dentry->d_sb;
+	inode = d_inode(src_dentry);
+	if (au_ibtop(inode) <= a->bdst)
+		h_inode = au_h_iptr(inode, a->bdst);
+	if (!h_inode || !h_inode->i_nlink) {
+		/* copyup src_dentry as the name of dentry. */
+		bbot = au_dbbot(dentry);
+		if (bbot < a->bsrc)
+			au_set_dbbot(dentry, a->bsrc);
+		au_set_h_dptr(dentry, a->bsrc,
+			      dget(au_h_dptr(src_dentry, a->bsrc)));
+		dget(a->h_path.dentry);
+		au_set_h_dptr(dentry, a->bdst, NULL);
+		AuDbg("temporary d_inode...\n");
+		spin_lock(&dentry->d_lock);
+		dentry->d_inode = d_inode(src_dentry); /* tmp */
+		spin_unlock(&dentry->d_lock);
+		h_file = au_h_open_pre(dentry, a->bsrc, /*force_wr*/0);
+		if (IS_ERR(h_file))
+			err = PTR_ERR(h_file);
+		else {
+			struct au_cp_generic cpg = {
+				.dentry	= dentry,
+				.bdst	= a->bdst,
+				.bsrc	= -1,
+				.len	= -1,
+				.pin	= &a->pin,
+				.flags	= AuCpup_KEEPLINO
+			};
+			err = au_sio_cpup_simple(&cpg);
+			au_h_open_post(dentry, a->bsrc, h_file);
+			if (!err) {
+				dput(a->h_path.dentry);
+				a->h_path.dentry = au_h_dptr(dentry, a->bdst);
+			} else
+				au_set_h_dptr(dentry, a->bdst,
+					      a->h_path.dentry);
+		}
+		spin_lock(&dentry->d_lock);
+		dentry->d_inode = NULL; /* restore */
+		spin_unlock(&dentry->d_lock);
+		AuDbg("temporary d_inode...done\n");
+		au_set_h_dptr(dentry, a->bsrc, NULL);
+		au_set_dbbot(dentry, bbot);
+	} else {
+		/* the inode of src_dentry already exists on a.bdst branch */
+		h_src_dentry = d_find_alias(h_inode);
+		if (!h_src_dentry && au_plink_test(inode)) {
+			plink = 1;
+			h_src_dentry = au_plink_lkup(inode, a->bdst);
+			err = PTR_ERR(h_src_dentry);
+			if (IS_ERR(h_src_dentry))
+				goto out;
+
+			if (unlikely(d_is_negative(h_src_dentry))) {
+				dput(h_src_dentry);
+				h_src_dentry = NULL;
+			}
+
+		}
+		if (h_src_dentry) {
+			delegated = NULL;
+			err = vfsub_link(h_src_dentry, au_pinned_h_dir(&a->pin),
+					 &a->h_path, &delegated);
+			if (unlikely(err == -EWOULDBLOCK)) {
+				pr_warn("cannot retry for NFSv4 delegation"
+					" for an internal link\n");
+				iput(delegated);
+			}
+			dput(h_src_dentry);
+		} else {
+			AuIOErr("no dentry found for hi%lu on b%d\n",
+				h_inode->i_ino, a->bdst);
+			err = -EIO;
+		}
+	}
+
+	if (!err && !plink)
+		au_plink_append(inode, a->bdst, a->h_path.dentry);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int aufs_link(struct dentry *src_dentry, struct inode *dir,
+	      struct dentry *dentry)
+{
+	int err, rerr;
+	struct au_dtime dt;
+	struct au_link_args *a;
+	struct dentry *wh_dentry, *h_src_dentry;
+	struct inode *inode, *delegated;
+	struct super_block *sb;
+	struct au_wr_dir_args wr_dir_args = {
+		/* .force_btgt	= -1, */
+		.flags		= AuWrDir_ADD_ENTRY
+	};
+
+	IMustLock(dir);
+	inode = d_inode(src_dentry);
+	IMustLock(inode);
+
+	err = -ENOMEM;
+	a = kzalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	a->parent = dentry->d_parent; /* dir inode is locked */
+	err = aufs_read_and_write_lock2(dentry, src_dentry,
+					AuLock_NOPLM | AuLock_GEN);
+	if (unlikely(err))
+		goto out_kfree;
+	err = au_d_linkable(src_dentry);
+	if (unlikely(err))
+		goto out_unlock;
+	err = au_d_may_add(dentry);
+	if (unlikely(err))
+		goto out_unlock;
+
+	a->src_parent = dget_parent(src_dentry);
+	wr_dir_args.force_btgt = au_ibtop(inode);
+
+	di_write_lock_parent(a->parent);
+	wr_dir_args.force_btgt = au_wbr(dentry, wr_dir_args.force_btgt);
+	wh_dentry = lock_hdir_lkup_wh(dentry, &dt, src_dentry, &a->pin,
+				      &wr_dir_args);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry))
+		goto out_parent;
+
+	err = 0;
+	sb = dentry->d_sb;
+	a->bdst = au_dbtop(dentry);
+	a->h_path.dentry = au_h_dptr(dentry, a->bdst);
+	a->h_path.mnt = au_sbr_mnt(sb, a->bdst);
+	a->bsrc = au_ibtop(inode);
+	h_src_dentry = au_h_d_alias(src_dentry, a->bsrc);
+	if (!h_src_dentry && au_di(src_dentry)->di_tmpfile)
+		h_src_dentry = dget(au_hi_wh(inode, a->bsrc));
+	if (!h_src_dentry) {
+		a->bsrc = au_dbtop(src_dentry);
+		h_src_dentry = au_h_d_alias(src_dentry, a->bsrc);
+		AuDebugOn(!h_src_dentry);
+	} else if (IS_ERR(h_src_dentry)) {
+		err = PTR_ERR(h_src_dentry);
+		goto out_parent;
+	}
+
+	/*
+	 * aufs doesn't touch the credential so
+	 * security_dentry_create_files_as() is unnecessary.
+	 */
+	if (au_opt_test(au_mntflags(sb), PLINK)) {
+		if (a->bdst < a->bsrc
+		    /* && h_src_dentry->d_sb != a->h_path.dentry->d_sb */)
+			err = au_cpup_or_link(src_dentry, dentry, a);
+		else {
+			delegated = NULL;
+			err = vfsub_link(h_src_dentry, au_pinned_h_dir(&a->pin),
+					 &a->h_path, &delegated);
+			if (unlikely(err == -EWOULDBLOCK)) {
+				pr_warn("cannot retry for NFSv4 delegation"
+					" for an internal link\n");
+				iput(delegated);
+			}
+		}
+		dput(h_src_dentry);
+	} else {
+		/*
+		 * copyup src_dentry to the branch we process,
+		 * and then link(2) to it.
+		 */
+		dput(h_src_dentry);
+		if (a->bdst < a->bsrc
+		    /* && h_src_dentry->d_sb != a->h_path.dentry->d_sb */) {
+			au_unpin(&a->pin);
+			di_write_unlock(a->parent);
+			err = au_cpup_before_link(src_dentry, a);
+			di_write_lock_parent(a->parent);
+			if (!err)
+				err = au_pin(&a->pin, dentry, a->bdst,
+					     au_opt_udba(sb),
+					     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+			if (unlikely(err))
+				goto out_wh;
+		}
+		if (!err) {
+			h_src_dentry = au_h_dptr(src_dentry, a->bdst);
+			err = -ENOENT;
+			if (h_src_dentry && d_is_positive(h_src_dentry)) {
+				delegated = NULL;
+				err = vfsub_link(h_src_dentry,
+						 au_pinned_h_dir(&a->pin),
+						 &a->h_path, &delegated);
+				if (unlikely(err == -EWOULDBLOCK)) {
+					pr_warn("cannot retry"
+						" for NFSv4 delegation"
+						" for an internal link\n");
+					iput(delegated);
+				}
+			}
+		}
+	}
+	if (unlikely(err))
+		goto out_unpin;
+
+	if (wh_dentry) {
+		a->h_path.dentry = wh_dentry;
+		err = au_wh_unlink_dentry(au_pinned_h_dir(&a->pin), &a->h_path,
+					  dentry);
+		if (unlikely(err))
+			goto out_revert;
+	}
+
+	au_dir_ts(dir, a->bdst);
+	inode_inc_iversion(dir);
+	inc_nlink(inode);
+	inode->i_ctime = dir->i_ctime;
+	d_instantiate(dentry, au_igrab(inode));
+	if (d_unhashed(a->h_path.dentry))
+		/* some filesystem calls d_drop() */
+		d_drop(dentry);
+	/* some filesystems consume an inode even hardlink */
+	au_fhsm_wrote(sb, a->bdst, /*force*/0);
+	goto out_unpin; /* success */
+
+out_revert:
+	/* no delegation since it is just created */
+	rerr = vfsub_unlink(au_pinned_h_dir(&a->pin), &a->h_path,
+			    /*delegated*/NULL, /*force*/0);
+	if (unlikely(rerr)) {
+		AuIOErr("%pd reverting failed(%d, %d)\n", dentry, err, rerr);
+		err = -EIO;
+	}
+	au_dtime_revert(&dt);
+out_unpin:
+	au_unpin(&a->pin);
+out_wh:
+	dput(wh_dentry);
+out_parent:
+	di_write_unlock(a->parent);
+	dput(a->src_parent);
+out_unlock:
+	if (unlikely(err)) {
+		au_update_dbtop(dentry);
+		d_drop(dentry);
+	}
+	aufs_read_and_write_unlock2(dentry, src_dentry);
+out_kfree:
+	au_kfree_rcu(a);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int aufs_mkdir(struct user_namespace *userns, struct inode *dir,
+	       struct dentry *dentry, umode_t mode)
+{
+	int err, rerr;
+	aufs_bindex_t bindex;
+	unsigned char diropq;
+	struct path h_path;
+	struct dentry *wh_dentry, *parent, *opq_dentry;
+	struct inode *h_inode;
+	struct super_block *sb;
+	struct {
+		struct au_pin pin;
+		struct au_dtime dt;
+	} *a; /* reduce the stack usage */
+	struct au_wr_dir_args wr_dir_args = {
+		.force_btgt	= -1,
+		.flags		= AuWrDir_ADD_ENTRY | AuWrDir_ISDIR
+	};
+
+	IMustLock(dir);
+
+	err = -ENOMEM;
+	a = kmalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	err = aufs_read_lock(dentry, AuLock_DW | AuLock_GEN);
+	if (unlikely(err))
+		goto out_free;
+	err = au_d_may_add(dentry);
+	if (unlikely(err))
+		goto out_unlock;
+
+	parent = dentry->d_parent; /* dir inode is locked */
+	di_write_lock_parent(parent);
+	wh_dentry = lock_hdir_lkup_wh(dentry, &a->dt, /*src_dentry*/NULL,
+				      &a->pin, &wr_dir_args);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry))
+		goto out_parent;
+
+	sb = dentry->d_sb;
+	bindex = au_dbtop(dentry);
+	h_path.dentry = au_h_dptr(dentry, bindex);
+	h_path.mnt = au_sbr_mnt(sb, bindex);
+	err = vfsub_mkdir(au_pinned_h_dir(&a->pin), &h_path, mode);
+	if (unlikely(err))
+		goto out_unpin;
+
+	/* make the dir opaque */
+	diropq = 0;
+	h_inode = d_inode(h_path.dentry);
+	if (wh_dentry
+	    || au_opt_test(au_mntflags(sb), ALWAYS_DIROPQ)) {
+		inode_lock_nested(h_inode, AuLsc_I_CHILD);
+		opq_dentry = au_diropq_create(dentry, bindex);
+		inode_unlock(h_inode);
+		err = PTR_ERR(opq_dentry);
+		if (IS_ERR(opq_dentry))
+			goto out_dir;
+		dput(opq_dentry);
+		diropq = 1;
+	}
+
+	err = epilog(dir, bindex, wh_dentry, dentry);
+	if (!err) {
+		inc_nlink(dir);
+		goto out_unpin; /* success */
+	}
+
+	/* revert */
+	if (diropq) {
+		AuLabel(revert opq);
+		inode_lock_nested(h_inode, AuLsc_I_CHILD);
+		rerr = au_diropq_remove(dentry, bindex);
+		inode_unlock(h_inode);
+		if (rerr) {
+			AuIOErr("%pd reverting diropq failed(%d, %d)\n",
+				dentry, err, rerr);
+			err = -EIO;
+		}
+	}
+
+out_dir:
+	AuLabel(revert dir);
+	rerr = vfsub_rmdir(au_pinned_h_dir(&a->pin), &h_path);
+	if (rerr) {
+		AuIOErr("%pd reverting dir failed(%d, %d)\n",
+			dentry, err, rerr);
+		err = -EIO;
+	}
+	au_dtime_revert(&a->dt);
+out_unpin:
+	au_unpin(&a->pin);
+	dput(wh_dentry);
+out_parent:
+	di_write_unlock(parent);
+out_unlock:
+	if (unlikely(err)) {
+		au_update_dbtop(dentry);
+		d_drop(dentry);
+	}
+	aufs_read_unlock(dentry, AuLock_DW);
+out_free:
+	au_kfree_rcu(a);
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/i_op_del.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/i_op_del.c
@@ -0,0 +1,522 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode operations (del entry)
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+/*
+ * decide if a new whiteout for @dentry is necessary or not.
+ * when it is necessary, prepare the parent dir for the upper branch whose
+ * branch index is @bcpup for creation. the actual creation of the whiteout will
+ * be done by caller.
+ * return value:
+ * 0: wh is unnecessary
+ * plus: wh is necessary
+ * minus: error
+ */
+int au_wr_dir_need_wh(struct dentry *dentry, int isdir, aufs_bindex_t *bcpup)
+{
+	int need_wh, err;
+	aufs_bindex_t btop;
+	struct super_block *sb;
+
+	sb = dentry->d_sb;
+	btop = au_dbtop(dentry);
+	if (*bcpup < 0) {
+		*bcpup = btop;
+		if (au_test_ro(sb, btop, d_inode(dentry))) {
+			err = AuWbrCopyup(au_sbi(sb), dentry);
+			*bcpup = err;
+			if (unlikely(err < 0))
+				goto out;
+		}
+	} else
+		AuDebugOn(btop < *bcpup
+			  || au_test_ro(sb, *bcpup, d_inode(dentry)));
+	AuDbg("bcpup %d, btop %d\n", *bcpup, btop);
+
+	if (*bcpup != btop) {
+		err = au_cpup_dirs(dentry, *bcpup);
+		if (unlikely(err))
+			goto out;
+		need_wh = 1;
+	} else {
+		struct au_dinfo *dinfo, *tmp;
+
+		need_wh = -ENOMEM;
+		dinfo = au_di(dentry);
+		tmp = au_di_alloc(sb, AuLsc_DI_TMP);
+		if (tmp) {
+			au_di_cp(tmp, dinfo);
+			au_di_swap(tmp, dinfo);
+			/* returns the number of positive dentries */
+			need_wh = au_lkup_dentry(dentry, btop + 1,
+						 /* AuLkup_IGNORE_PERM */ 0);
+			au_di_swap(tmp, dinfo);
+			au_rw_write_unlock(&tmp->di_rwsem);
+			au_di_free(tmp);
+		}
+	}
+	AuDbg("need_wh %d\n", need_wh);
+	err = need_wh;
+
+out:
+	return err;
+}
+
+/*
+ * simple tests for the del-entry operations.
+ * following the checks in vfs, plus the parent-child relationship.
+ */
+int au_may_del(struct dentry *dentry, aufs_bindex_t bindex,
+	       struct dentry *h_parent, int isdir)
+{
+	int err;
+	umode_t h_mode;
+	struct dentry *h_dentry, *h_latest;
+	struct inode *h_inode;
+	struct path h_ppath;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct user_namespace *h_userns;
+
+	h_dentry = au_h_dptr(dentry, bindex);
+	if (d_really_is_positive(dentry)) {
+		err = -ENOENT;
+		if (unlikely(d_is_negative(h_dentry)))
+			goto out;
+		h_inode = d_inode(h_dentry);
+		if (unlikely(!h_inode->i_nlink))
+			goto out;
+
+		h_mode = h_inode->i_mode;
+		if (!isdir) {
+			err = -EISDIR;
+			if (unlikely(S_ISDIR(h_mode)))
+				goto out;
+		} else if (unlikely(!S_ISDIR(h_mode))) {
+			err = -ENOTDIR;
+			goto out;
+		}
+	} else {
+		/* rename(2) case */
+		err = -EIO;
+		if (unlikely(d_is_positive(h_dentry)))
+			goto out;
+	}
+
+	err = -ENOENT;
+	/* expected parent dir is locked */
+	if (unlikely(h_parent != h_dentry->d_parent))
+		goto out;
+	err = 0;
+
+	/*
+	 * rmdir a dir may break the consistency on some filesystem.
+	 * let's try heavy test.
+	 */
+	err = -EACCES;
+	sb = dentry->d_sb;
+	br = au_sbr(sb, bindex);
+	h_userns = au_br_userns(br);
+	if (unlikely(!au_opt_test(au_mntflags(sb), DIRPERM1)
+		     && au_test_h_perm(h_userns, d_inode(h_parent),
+				       MAY_EXEC | MAY_WRITE)))
+		goto out;
+
+	h_ppath.dentry = h_parent;
+	h_ppath.mnt = au_br_mnt(br);
+	h_latest = au_sio_lkup_one(h_userns, &dentry->d_name, &h_ppath);
+	err = -EIO;
+	if (IS_ERR(h_latest))
+		goto out;
+	if (h_latest == h_dentry)
+		err = 0;
+	dput(h_latest);
+
+out:
+	return err;
+}
+
+/*
+ * decide the branch where we operate for @dentry. the branch index will be set
+ * @rbcpup. after deciding it, 'pin' it and store the timestamps of the parent
+ * dir for reverting.
+ * when a new whiteout is necessary, create it.
+ */
+static struct dentry*
+lock_hdir_create_wh(struct dentry *dentry, int isdir, aufs_bindex_t *rbcpup,
+		    struct au_dtime *dt, struct au_pin *pin)
+{
+	struct dentry *wh_dentry;
+	struct super_block *sb;
+	struct path h_path;
+	int err, need_wh;
+	unsigned int udba;
+	aufs_bindex_t bcpup;
+
+	need_wh = au_wr_dir_need_wh(dentry, isdir, rbcpup);
+	wh_dentry = ERR_PTR(need_wh);
+	if (unlikely(need_wh < 0))
+		goto out;
+
+	sb = dentry->d_sb;
+	udba = au_opt_udba(sb);
+	bcpup = *rbcpup;
+	err = au_pin(pin, dentry, bcpup, udba,
+		     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+	wh_dentry = ERR_PTR(err);
+	if (unlikely(err))
+		goto out;
+
+	h_path.dentry = au_pinned_h_parent(pin);
+	if (udba != AuOpt_UDBA_NONE
+	    && au_dbtop(dentry) == bcpup) {
+		err = au_may_del(dentry, bcpup, h_path.dentry, isdir);
+		wh_dentry = ERR_PTR(err);
+		if (unlikely(err))
+			goto out_unpin;
+	}
+
+	h_path.mnt = au_sbr_mnt(sb, bcpup);
+	au_dtime_store(dt, au_pinned_parent(pin), &h_path);
+	wh_dentry = NULL;
+	if (!need_wh)
+		goto out; /* success, no need to create whiteout */
+
+	wh_dentry = au_wh_create(dentry, bcpup, h_path.dentry);
+	if (IS_ERR(wh_dentry))
+		goto out_unpin;
+
+	/* returns with the parent is locked and wh_dentry is dget-ed */
+	goto out; /* success */
+
+out_unpin:
+	au_unpin(pin);
+out:
+	return wh_dentry;
+}
+
+/*
+ * when removing a dir, rename it to a unique temporary whiteout-ed name first
+ * in order to be revertible and save time for removing many child whiteouts
+ * under the dir.
+ * returns 1 when there are too many child whiteout and caller should remove
+ * them asynchronously. returns 0 when the number of children is enough small to
+ * remove now or the branch fs is a remote fs.
+ * otherwise return an error.
+ */
+static int renwh_and_rmdir(struct dentry *dentry, aufs_bindex_t bindex,
+			   struct au_nhash *whlist, struct inode *dir)
+{
+	int rmdir_later, err, dirwh;
+	struct dentry *h_dentry;
+	struct super_block *sb;
+	struct inode *inode;
+
+	sb = dentry->d_sb;
+	SiMustAnyLock(sb);
+	h_dentry = au_h_dptr(dentry, bindex);
+	err = au_whtmp_ren(h_dentry, au_sbr(sb, bindex));
+	if (unlikely(err))
+		goto out;
+
+	/* stop monitoring */
+	inode = d_inode(dentry);
+	au_hn_free(au_hi(inode, bindex));
+
+	if (!au_test_fs_remote(h_dentry->d_sb)) {
+		dirwh = au_sbi(sb)->si_dirwh;
+		rmdir_later = (dirwh <= 1);
+		if (!rmdir_later)
+			rmdir_later = au_nhash_test_longer_wh(whlist, bindex,
+							      dirwh);
+		if (rmdir_later)
+			return rmdir_later;
+	}
+
+	err = au_whtmp_rmdir(dir, bindex, h_dentry, whlist);
+	if (unlikely(err)) {
+		AuIOErr("rmdir %pd, b%d failed, %d. ignored\n",
+			h_dentry, bindex, err);
+		err = 0;
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * final procedure for deleting a entry.
+ * maintain dentry and iattr.
+ */
+static void epilog(struct inode *dir, struct dentry *dentry,
+		   aufs_bindex_t bindex)
+{
+	struct inode *inode;
+
+	inode = d_inode(dentry);
+	d_drop(dentry);
+	inode->i_ctime = dir->i_ctime;
+
+	au_dir_ts(dir, bindex);
+	inode_inc_iversion(dir);
+}
+
+/*
+ * when an error happened, remove the created whiteout and revert everything.
+ */
+static int do_revert(int err, struct inode *dir, aufs_bindex_t bindex,
+		     aufs_bindex_t bwh, struct dentry *wh_dentry,
+		     struct dentry *dentry, struct au_dtime *dt)
+{
+	int rerr;
+	struct path h_path = {
+		.dentry	= wh_dentry,
+		.mnt	= au_sbr_mnt(dir->i_sb, bindex)
+	};
+
+	rerr = au_wh_unlink_dentry(au_h_iptr(dir, bindex), &h_path, dentry);
+	if (!rerr) {
+		au_set_dbwh(dentry, bwh);
+		au_dtime_revert(dt);
+		return 0;
+	}
+
+	AuIOErr("%pd reverting whiteout failed(%d, %d)\n", dentry, err, rerr);
+	return -EIO;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int aufs_unlink(struct inode *dir, struct dentry *dentry)
+{
+	int err;
+	aufs_bindex_t bwh, bindex, btop;
+	struct inode *inode, *h_dir, *delegated;
+	struct dentry *parent, *wh_dentry;
+	/* to reduce stack size */
+	struct {
+		struct au_dtime dt;
+		struct au_pin pin;
+		struct path h_path;
+	} *a;
+
+	IMustLock(dir);
+
+	err = -ENOMEM;
+	a = kmalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	err = aufs_read_lock(dentry, AuLock_DW | AuLock_GEN);
+	if (unlikely(err))
+		goto out_free;
+	err = au_d_hashed_positive(dentry);
+	if (unlikely(err))
+		goto out_unlock;
+	inode = d_inode(dentry);
+	IMustLock(inode);
+	err = -EISDIR;
+	if (unlikely(d_is_dir(dentry)))
+		goto out_unlock; /* possible? */
+
+	btop = au_dbtop(dentry);
+	bwh = au_dbwh(dentry);
+	bindex = -1;
+	parent = dentry->d_parent; /* dir inode is locked */
+	di_write_lock_parent(parent);
+	wh_dentry = lock_hdir_create_wh(dentry, /*isdir*/0, &bindex, &a->dt,
+					&a->pin);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry))
+		goto out_parent;
+
+	a->h_path.mnt = au_sbr_mnt(dentry->d_sb, btop);
+	a->h_path.dentry = au_h_dptr(dentry, btop);
+	dget(a->h_path.dentry);
+	if (bindex == btop) {
+		h_dir = au_pinned_h_dir(&a->pin);
+		delegated = NULL;
+		err = vfsub_unlink(h_dir, &a->h_path, &delegated, /*force*/0);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal unlink\n");
+			iput(delegated);
+		}
+	} else {
+		/* dir inode is locked */
+		h_dir = d_inode(wh_dentry->d_parent);
+		IMustLock(h_dir);
+		err = 0;
+	}
+
+	if (!err) {
+		vfsub_drop_nlink(inode);
+		epilog(dir, dentry, bindex);
+
+		/* update target timestamps */
+		if (bindex == btop) {
+			vfsub_update_h_iattr(&a->h_path, /*did*/NULL);
+			/*ignore*/
+			inode->i_ctime = d_inode(a->h_path.dentry)->i_ctime;
+		} else
+			/* todo: this timestamp may be reverted later */
+			inode->i_ctime = h_dir->i_ctime;
+		goto out_unpin; /* success */
+	}
+
+	/* revert */
+	if (wh_dentry) {
+		int rerr;
+
+		rerr = do_revert(err, dir, bindex, bwh, wh_dentry, dentry,
+				 &a->dt);
+		if (rerr)
+			err = rerr;
+	}
+
+out_unpin:
+	au_unpin(&a->pin);
+	dput(wh_dentry);
+	dput(a->h_path.dentry);
+out_parent:
+	di_write_unlock(parent);
+out_unlock:
+	aufs_read_unlock(dentry, AuLock_DW);
+out_free:
+	au_kfree_rcu(a);
+out:
+	return err;
+}
+
+int aufs_rmdir(struct inode *dir, struct dentry *dentry)
+{
+	int err, rmdir_later;
+	aufs_bindex_t bwh, bindex, btop;
+	struct inode *inode;
+	struct dentry *parent, *wh_dentry, *h_dentry;
+	struct au_whtmp_rmdir *args;
+	/* to reduce stack size */
+	struct {
+		struct au_dtime dt;
+		struct au_pin pin;
+	} *a;
+
+	IMustLock(dir);
+
+	err = -ENOMEM;
+	a = kmalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	err = aufs_read_lock(dentry, AuLock_DW | AuLock_FLUSH | AuLock_GEN);
+	if (unlikely(err))
+		goto out_free;
+	err = au_alive_dir(dentry);
+	if (unlikely(err))
+		goto out_unlock;
+	inode = d_inode(dentry);
+	IMustLock(inode);
+	err = -ENOTDIR;
+	if (unlikely(!d_is_dir(dentry)))
+		goto out_unlock; /* possible? */
+
+	err = -ENOMEM;
+	args = au_whtmp_rmdir_alloc(dir->i_sb, GFP_NOFS);
+	if (unlikely(!args))
+		goto out_unlock;
+
+	parent = dentry->d_parent; /* dir inode is locked */
+	di_write_lock_parent(parent);
+	err = au_test_empty(dentry, &args->whlist);
+	if (unlikely(err))
+		goto out_parent;
+
+	btop = au_dbtop(dentry);
+	bwh = au_dbwh(dentry);
+	bindex = -1;
+	wh_dentry = lock_hdir_create_wh(dentry, /*isdir*/1, &bindex, &a->dt,
+					&a->pin);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry))
+		goto out_parent;
+
+	h_dentry = au_h_dptr(dentry, btop);
+	dget(h_dentry);
+	rmdir_later = 0;
+	if (bindex == btop) {
+		err = renwh_and_rmdir(dentry, btop, &args->whlist, dir);
+		if (err > 0) {
+			rmdir_later = err;
+			err = 0;
+		}
+	} else {
+		/* stop monitoring */
+		au_hn_free(au_hi(inode, btop));
+
+		/* dir inode is locked */
+		IMustLock(d_inode(wh_dentry->d_parent));
+		err = 0;
+	}
+
+	if (!err) {
+		vfsub_dead_dir(inode);
+		au_set_dbdiropq(dentry, -1);
+		epilog(dir, dentry, bindex);
+
+		if (rmdir_later) {
+			au_whtmp_kick_rmdir(dir, btop, h_dentry, args);
+			args = NULL;
+		}
+
+		goto out_unpin; /* success */
+	}
+
+	/* revert */
+	AuLabel(revert);
+	if (wh_dentry) {
+		int rerr;
+
+		rerr = do_revert(err, dir, bindex, bwh, wh_dentry, dentry,
+				 &a->dt);
+		if (rerr)
+			err = rerr;
+	}
+
+out_unpin:
+	au_unpin(&a->pin);
+	dput(wh_dentry);
+	dput(h_dentry);
+out_parent:
+	di_write_unlock(parent);
+	if (args)
+		au_whtmp_rmdir_free(args);
+out_unlock:
+	aufs_read_unlock(dentry, AuLock_DW);
+out_free:
+	au_kfree_rcu(a);
+out:
+	AuTraceErr(err);
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/i_op_ren.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/i_op_ren.c
@@ -0,0 +1,1257 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode operation (rename entry)
+ * todo: this is crazy monster
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+enum { AuSRC, AuDST, AuSrcDst };
+enum { AuPARENT, AuCHILD, AuParentChild };
+
+#define AuRen_ISDIR_SRC		1
+#define AuRen_ISDIR_DST		(1 << 1)
+#define AuRen_ISSAMEDIR		(1 << 2)
+#define AuRen_WHSRC		(1 << 3)
+#define AuRen_WHDST		(1 << 4)
+#define AuRen_MNT_WRITE		(1 << 5)
+#define AuRen_DT_DSTDIR		(1 << 6)
+#define AuRen_DIROPQ_SRC	(1 << 7)
+#define AuRen_DIROPQ_DST	(1 << 8)
+#define AuRen_DIRREN		(1 << 9)
+#define AuRen_DROPPED_SRC	(1 << 10)
+#define AuRen_DROPPED_DST	(1 << 11)
+#define au_ftest_ren(flags, name)	((flags) & AuRen_##name)
+#define au_fset_ren(flags, name) \
+	do { (flags) |= AuRen_##name; } while (0)
+#define au_fclr_ren(flags, name) \
+	do { (flags) &= ~AuRen_##name; } while (0)
+
+#ifndef CONFIG_AUFS_DIRREN
+#undef AuRen_DIRREN
+#define AuRen_DIRREN		0
+#endif
+
+struct au_ren_args {
+	struct {
+		struct dentry *dentry, *h_dentry, *parent, *h_parent,
+			*wh_dentry;
+		struct inode *dir, *inode;
+		struct au_hinode *hdir, *hinode;
+		struct au_dtime dt[AuParentChild];
+		aufs_bindex_t btop, bdiropq;
+	} sd[AuSrcDst];
+
+#define src_dentry	sd[AuSRC].dentry
+#define src_dir		sd[AuSRC].dir
+#define src_inode	sd[AuSRC].inode
+#define src_h_dentry	sd[AuSRC].h_dentry
+#define src_parent	sd[AuSRC].parent
+#define src_h_parent	sd[AuSRC].h_parent
+#define src_wh_dentry	sd[AuSRC].wh_dentry
+#define src_hdir	sd[AuSRC].hdir
+#define src_hinode	sd[AuSRC].hinode
+#define src_h_dir	sd[AuSRC].hdir->hi_inode
+#define src_dt		sd[AuSRC].dt
+#define src_btop	sd[AuSRC].btop
+#define src_bdiropq	sd[AuSRC].bdiropq
+
+#define dst_dentry	sd[AuDST].dentry
+#define dst_dir		sd[AuDST].dir
+#define dst_inode	sd[AuDST].inode
+#define dst_h_dentry	sd[AuDST].h_dentry
+#define dst_parent	sd[AuDST].parent
+#define dst_h_parent	sd[AuDST].h_parent
+#define dst_wh_dentry	sd[AuDST].wh_dentry
+#define dst_hdir	sd[AuDST].hdir
+#define dst_hinode	sd[AuDST].hinode
+#define dst_h_dir	sd[AuDST].hdir->hi_inode
+#define dst_dt		sd[AuDST].dt
+#define dst_btop	sd[AuDST].btop
+#define dst_bdiropq	sd[AuDST].bdiropq
+
+	struct dentry *h_trap;
+	struct au_branch *br;
+	struct path h_path;
+	struct au_nhash whlist;
+	aufs_bindex_t btgt, src_bwh;
+
+	struct {
+		unsigned short auren_flags;
+		unsigned char flags;	/* syscall parameter */
+		unsigned char exchange;
+	} __packed;
+
+	struct au_whtmp_rmdir *thargs;
+	struct dentry *h_dst;
+	struct au_hinode *h_root;
+};
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * functions for reverting.
+ * when an error happened in a single rename systemcall, we should revert
+ * everything as if nothing happened.
+ * we don't need to revert the copied-up/down the parent dir since they are
+ * harmless.
+ */
+
+#define RevertFailure(fmt, ...) do { \
+	AuIOErr("revert failure: " fmt " (%d, %d)\n", \
+		##__VA_ARGS__, err, rerr); \
+	err = -EIO; \
+} while (0)
+
+static void au_ren_do_rev_diropq(int err, struct au_ren_args *a, int idx)
+{
+	int rerr;
+	struct dentry *d;
+#define src_or_dst(member) a->sd[idx].member
+
+	d = src_or_dst(dentry); /* {src,dst}_dentry */
+	au_hn_inode_lock_nested(src_or_dst(hinode), AuLsc_I_CHILD);
+	rerr = au_diropq_remove(d, a->btgt);
+	au_hn_inode_unlock(src_or_dst(hinode));
+	au_set_dbdiropq(d, src_or_dst(bdiropq));
+	if (rerr)
+		RevertFailure("remove diropq %pd", d);
+
+#undef src_or_dst_
+}
+
+static void au_ren_rev_diropq(int err, struct au_ren_args *a)
+{
+	if (au_ftest_ren(a->auren_flags, DIROPQ_SRC))
+		au_ren_do_rev_diropq(err, a, AuSRC);
+	if (au_ftest_ren(a->auren_flags, DIROPQ_DST))
+		au_ren_do_rev_diropq(err, a, AuDST);
+}
+
+static void au_ren_rev_rename(int err, struct au_ren_args *a)
+{
+	int rerr;
+	struct inode *delegated;
+	struct path h_ppath = {
+		.dentry	= a->src_h_parent,
+		.mnt	= a->h_path.mnt
+	};
+
+	a->h_path.dentry = vfsub_lkup_one(&a->src_dentry->d_name, &h_ppath);
+	rerr = PTR_ERR(a->h_path.dentry);
+	if (IS_ERR(a->h_path.dentry)) {
+		RevertFailure("lkup one %pd", a->src_dentry);
+		return;
+	}
+
+	delegated = NULL;
+	rerr = vfsub_rename(a->dst_h_dir,
+			    au_h_dptr(a->src_dentry, a->btgt),
+			    a->src_h_dir, &a->h_path, &delegated, a->flags);
+	if (unlikely(rerr == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal rename\n");
+		iput(delegated);
+	}
+	d_drop(a->h_path.dentry);
+	dput(a->h_path.dentry);
+	/* au_set_h_dptr(a->src_dentry, a->btgt, NULL); */
+	if (rerr)
+		RevertFailure("rename %pd", a->src_dentry);
+}
+
+static void au_ren_rev_whtmp(int err, struct au_ren_args *a)
+{
+	int rerr;
+	struct inode *delegated;
+	struct path h_ppath = {
+		.dentry	= a->dst_h_parent,
+		.mnt	= a->h_path.mnt
+	};
+
+	a->h_path.dentry = vfsub_lkup_one(&a->dst_dentry->d_name, &h_ppath);
+	rerr = PTR_ERR(a->h_path.dentry);
+	if (IS_ERR(a->h_path.dentry)) {
+		RevertFailure("lkup one %pd", a->dst_dentry);
+		return;
+	}
+	if (d_is_positive(a->h_path.dentry)) {
+		d_drop(a->h_path.dentry);
+		dput(a->h_path.dentry);
+		return;
+	}
+
+	delegated = NULL;
+	rerr = vfsub_rename(a->dst_h_dir, a->h_dst, a->dst_h_dir, &a->h_path,
+			    &delegated, a->flags);
+	if (unlikely(rerr == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal rename\n");
+		iput(delegated);
+	}
+	d_drop(a->h_path.dentry);
+	dput(a->h_path.dentry);
+	if (!rerr)
+		au_set_h_dptr(a->dst_dentry, a->btgt, dget(a->h_dst));
+	else
+		RevertFailure("rename %pd", a->h_dst);
+}
+
+static void au_ren_rev_whsrc(int err, struct au_ren_args *a)
+{
+	int rerr;
+
+	a->h_path.dentry = a->src_wh_dentry;
+	rerr = au_wh_unlink_dentry(a->src_h_dir, &a->h_path, a->src_dentry);
+	au_set_dbwh(a->src_dentry, a->src_bwh);
+	if (rerr)
+		RevertFailure("unlink %pd", a->src_wh_dentry);
+}
+#undef RevertFailure
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * when we have to copyup the renaming entry, do it with the rename-target name
+ * in order to minimize the cost (the later actual rename is unnecessary).
+ * otherwise rename it on the target branch.
+ */
+static int au_ren_or_cpup(struct au_ren_args *a)
+{
+	int err;
+	struct dentry *d;
+	struct inode *delegated;
+
+	d = a->src_dentry;
+	if (au_dbtop(d) == a->btgt) {
+		a->h_path.dentry = a->dst_h_dentry;
+		AuDebugOn(au_dbtop(d) != a->btgt);
+		delegated = NULL;
+		err = vfsub_rename(a->src_h_dir, au_h_dptr(d, a->btgt),
+				   a->dst_h_dir, &a->h_path, &delegated,
+				   a->flags);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal rename\n");
+			iput(delegated);
+		}
+	} else
+		BUG();
+
+	if (!err && a->h_dst)
+		/* it will be set to dinfo later */
+		dget(a->h_dst);
+
+	return err;
+}
+
+/* cf. aufs_rmdir() */
+static int au_ren_del_whtmp(struct au_ren_args *a)
+{
+	int err;
+	struct inode *dir;
+
+	dir = a->dst_dir;
+	SiMustAnyLock(dir->i_sb);
+	if (!au_nhash_test_longer_wh(&a->whlist, a->btgt,
+				     au_sbi(dir->i_sb)->si_dirwh)
+	    || au_test_fs_remote(a->h_dst->d_sb)) {
+		err = au_whtmp_rmdir(dir, a->btgt, a->h_dst, &a->whlist);
+		if (unlikely(err))
+			pr_warn("failed removing whtmp dir %pd (%d), "
+				"ignored.\n", a->h_dst, err);
+	} else {
+		au_nhash_wh_free(&a->thargs->whlist);
+		a->thargs->whlist = a->whlist;
+		a->whlist.nh_num = 0;
+		au_whtmp_kick_rmdir(dir, a->btgt, a->h_dst, a->thargs);
+		dput(a->h_dst);
+		a->thargs = NULL;
+	}
+
+	return 0;
+}
+
+/* make it 'opaque' dir. */
+static int au_ren_do_diropq(struct au_ren_args *a, int idx)
+{
+	int err;
+	struct dentry *d, *diropq;
+#define src_or_dst(member) a->sd[idx].member
+
+	err = 0;
+	d = src_or_dst(dentry); /* {src,dst}_dentry */
+	src_or_dst(bdiropq) = au_dbdiropq(d);
+	src_or_dst(hinode) = au_hi(src_or_dst(inode), a->btgt);
+	au_hn_inode_lock_nested(src_or_dst(hinode), AuLsc_I_CHILD);
+	diropq = au_diropq_create(d, a->btgt);
+	au_hn_inode_unlock(src_or_dst(hinode));
+	if (IS_ERR(diropq))
+		err = PTR_ERR(diropq);
+	else
+		dput(diropq);
+
+#undef src_or_dst_
+	return err;
+}
+
+static int au_ren_diropq(struct au_ren_args *a)
+{
+	int err;
+	unsigned char always;
+	struct dentry *d;
+
+	err = 0;
+	d = a->dst_dentry; /* already renamed on the branch */
+	always = !!au_opt_test(au_mntflags(d->d_sb), ALWAYS_DIROPQ);
+	if (au_ftest_ren(a->auren_flags, ISDIR_SRC)
+	    && !au_ftest_ren(a->auren_flags, DIRREN)
+	    && a->btgt != au_dbdiropq(a->src_dentry)
+	    && (a->dst_wh_dentry
+		|| a->btgt <= au_dbdiropq(d)
+		/* hide the lower to keep xino */
+		/* the lowers may not be a dir, but we hide them anyway */
+		|| a->btgt < au_dbbot(d)
+		|| always)) {
+		AuDbg("here\n");
+		err = au_ren_do_diropq(a, AuSRC);
+		if (unlikely(err))
+			goto out;
+		au_fset_ren(a->auren_flags, DIROPQ_SRC);
+	}
+	if (!a->exchange)
+		goto out; /* success */
+
+	d = a->src_dentry; /* already renamed on the branch */
+	if (au_ftest_ren(a->auren_flags, ISDIR_DST)
+	    && a->btgt != au_dbdiropq(a->dst_dentry)
+	    && (a->btgt < au_dbdiropq(d)
+		|| a->btgt < au_dbbot(d)
+		|| always)) {
+		AuDbgDentry(a->src_dentry);
+		AuDbgDentry(a->dst_dentry);
+		err = au_ren_do_diropq(a, AuDST);
+		if (unlikely(err))
+			goto out_rev_src;
+		au_fset_ren(a->auren_flags, DIROPQ_DST);
+	}
+	goto out; /* success */
+
+out_rev_src:
+	AuDbg("err %d, reverting src\n", err);
+	au_ren_rev_diropq(err, a);
+out:
+	return err;
+}
+
+static int do_rename(struct au_ren_args *a)
+{
+	int err;
+	struct dentry *d, *h_d;
+
+	if (!a->exchange) {
+		/* prepare workqueue args for asynchronous rmdir */
+		h_d = a->dst_h_dentry;
+		if (au_ftest_ren(a->auren_flags, ISDIR_DST)
+		    /* && !au_ftest_ren(a->auren_flags, DIRREN) */
+		    && d_is_positive(h_d)) {
+			err = -ENOMEM;
+			a->thargs = au_whtmp_rmdir_alloc(a->src_dentry->d_sb,
+							 GFP_NOFS);
+			if (unlikely(!a->thargs))
+				goto out;
+			a->h_dst = dget(h_d);
+		}
+
+		/* create whiteout for src_dentry */
+		if (au_ftest_ren(a->auren_flags, WHSRC)) {
+			a->src_bwh = au_dbwh(a->src_dentry);
+			AuDebugOn(a->src_bwh >= 0);
+			a->src_wh_dentry = au_wh_create(a->src_dentry, a->btgt,
+							a->src_h_parent);
+			err = PTR_ERR(a->src_wh_dentry);
+			if (IS_ERR(a->src_wh_dentry))
+				goto out_thargs;
+		}
+
+		/* lookup whiteout for dentry */
+		if (au_ftest_ren(a->auren_flags, WHDST)) {
+			h_d = au_wh_lkup(a->dst_h_parent,
+					 &a->dst_dentry->d_name, a->br);
+			err = PTR_ERR(h_d);
+			if (IS_ERR(h_d))
+				goto out_whsrc;
+			if (d_is_negative(h_d))
+				dput(h_d);
+			else
+				a->dst_wh_dentry = h_d;
+		}
+
+		/* rename dentry to tmpwh */
+		if (a->thargs) {
+			err = au_whtmp_ren(a->dst_h_dentry, a->br);
+			if (unlikely(err))
+				goto out_whdst;
+
+			d = a->dst_dentry;
+			au_set_h_dptr(d, a->btgt, NULL);
+			err = au_lkup_neg(d, a->btgt, /*wh*/0);
+			if (unlikely(err))
+				goto out_whtmp;
+			a->dst_h_dentry = au_h_dptr(d, a->btgt);
+		}
+	}
+
+	BUG_ON(d_is_positive(a->dst_h_dentry) && a->src_btop != a->btgt);
+#if 0 /* debugging */
+	BUG_ON(!au_ftest_ren(a->auren_flags, DIRREN)
+	       && d_is_positive(a->dst_h_dentry)
+	       && a->src_btop != a->btgt);
+#endif
+
+	/* rename by vfs_rename or cpup */
+	err = au_ren_or_cpup(a);
+	if (unlikely(err))
+		/* leave the copied-up one */
+		goto out_whtmp;
+
+	/* make dir opaque */
+	err = au_ren_diropq(a);
+	if (unlikely(err))
+		goto out_rename;
+
+	/* update target timestamps */
+	if (a->exchange) {
+		AuDebugOn(au_dbtop(a->dst_dentry) != a->btgt);
+		a->h_path.dentry = au_h_dptr(a->dst_dentry, a->btgt);
+		vfsub_update_h_iattr(&a->h_path, /*did*/NULL); /*ignore*/
+		a->dst_inode->i_ctime = d_inode(a->h_path.dentry)->i_ctime;
+	}
+	AuDebugOn(au_dbtop(a->src_dentry) != a->btgt);
+	a->h_path.dentry = au_h_dptr(a->src_dentry, a->btgt);
+	vfsub_update_h_iattr(&a->h_path, /*did*/NULL); /*ignore*/
+	a->src_inode->i_ctime = d_inode(a->h_path.dentry)->i_ctime;
+
+	if (!a->exchange) {
+		/* remove whiteout for dentry */
+		if (a->dst_wh_dentry) {
+			a->h_path.dentry = a->dst_wh_dentry;
+			err = au_wh_unlink_dentry(a->dst_h_dir, &a->h_path,
+						  a->dst_dentry);
+			if (unlikely(err))
+				goto out_diropq;
+		}
+
+		/* remove whtmp */
+		if (a->thargs)
+			au_ren_del_whtmp(a); /* ignore this error */
+
+		au_fhsm_wrote(a->src_dentry->d_sb, a->btgt, /*force*/0);
+	}
+	err = 0;
+	goto out_success;
+
+out_diropq:
+	au_ren_rev_diropq(err, a);
+out_rename:
+	au_ren_rev_rename(err, a);
+	dput(a->h_dst);
+out_whtmp:
+	if (a->thargs)
+		au_ren_rev_whtmp(err, a);
+out_whdst:
+	dput(a->dst_wh_dentry);
+	a->dst_wh_dentry = NULL;
+out_whsrc:
+	if (a->src_wh_dentry)
+		au_ren_rev_whsrc(err, a);
+out_success:
+	dput(a->src_wh_dentry);
+	dput(a->dst_wh_dentry);
+out_thargs:
+	if (a->thargs) {
+		dput(a->h_dst);
+		au_whtmp_rmdir_free(a->thargs);
+		a->thargs = NULL;
+	}
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * test if @dentry dir can be rename destination or not.
+ * success means, it is a logically empty dir.
+ */
+static int may_rename_dstdir(struct dentry *dentry, struct au_nhash *whlist)
+{
+	return au_test_empty(dentry, whlist);
+}
+
+/*
+ * test if @a->src_dentry dir can be rename source or not.
+ * if it can, return 0.
+ * success means,
+ * - it is a logically empty dir.
+ * - or, it exists on writable branch and has no children including whiteouts
+ *   on the lower branch unless DIRREN is on.
+ */
+static int may_rename_srcdir(struct au_ren_args *a)
+{
+	int err;
+	unsigned int rdhash;
+	aufs_bindex_t btop, btgt;
+	struct dentry *dentry;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+
+	dentry = a->src_dentry;
+	sb = dentry->d_sb;
+	sbinfo = au_sbi(sb);
+	if (au_opt_test(sbinfo->si_mntflags, DIRREN))
+		au_fset_ren(a->auren_flags, DIRREN);
+
+	btgt = a->btgt;
+	btop = au_dbtop(dentry);
+	if (btop != btgt) {
+		struct au_nhash whlist;
+
+		SiMustAnyLock(sb);
+		rdhash = sbinfo->si_rdhash;
+		if (!rdhash)
+			rdhash = au_rdhash_est(au_dir_size(/*file*/NULL,
+							   dentry));
+		err = au_nhash_alloc(&whlist, rdhash, GFP_NOFS);
+		if (unlikely(err))
+			goto out;
+		err = au_test_empty(dentry, &whlist);
+		au_nhash_wh_free(&whlist);
+		goto out;
+	}
+
+	if (btop == au_dbtaildir(dentry))
+		return 0; /* success */
+
+	err = au_test_empty_lower(dentry);
+
+out:
+	if (err == -ENOTEMPTY) {
+		if (au_ftest_ren(a->auren_flags, DIRREN)) {
+			err = 0;
+		} else {
+			AuWarn1("renaming dir who has child(ren) on multiple "
+				"branches, is not supported\n");
+			err = -EXDEV;
+		}
+	}
+	return err;
+}
+
+/* side effect: sets whlist and h_dentry */
+static int au_ren_may_dir(struct au_ren_args *a)
+{
+	int err;
+	unsigned int rdhash;
+	struct dentry *d;
+
+	d = a->dst_dentry;
+	SiMustAnyLock(d->d_sb);
+
+	err = 0;
+	if (au_ftest_ren(a->auren_flags, ISDIR_DST) && a->dst_inode) {
+		rdhash = au_sbi(d->d_sb)->si_rdhash;
+		if (!rdhash)
+			rdhash = au_rdhash_est(au_dir_size(/*file*/NULL, d));
+		err = au_nhash_alloc(&a->whlist, rdhash, GFP_NOFS);
+		if (unlikely(err))
+			goto out;
+
+		if (!a->exchange) {
+			au_set_dbtop(d, a->dst_btop);
+			err = may_rename_dstdir(d, &a->whlist);
+			au_set_dbtop(d, a->btgt);
+		} else
+			err = may_rename_srcdir(a);
+	}
+	a->dst_h_dentry = au_h_dptr(d, au_dbtop(d));
+	if (unlikely(err))
+		goto out;
+
+	d = a->src_dentry;
+	a->src_h_dentry = au_h_dptr(d, au_dbtop(d));
+	if (au_ftest_ren(a->auren_flags, ISDIR_SRC)) {
+		err = may_rename_srcdir(a);
+		if (unlikely(err)) {
+			au_nhash_wh_free(&a->whlist);
+			a->whlist.nh_num = 0;
+		}
+	}
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * simple tests for rename.
+ * following the checks in vfs, plus the parent-child relationship.
+ */
+static int au_may_ren(struct au_ren_args *a)
+{
+	int err, isdir;
+	struct inode *h_inode;
+
+	if (a->src_btop == a->btgt) {
+		err = au_may_del(a->src_dentry, a->btgt, a->src_h_parent,
+				 au_ftest_ren(a->auren_flags, ISDIR_SRC));
+		if (unlikely(err))
+			goto out;
+		err = -EINVAL;
+		if (unlikely(a->src_h_dentry == a->h_trap))
+			goto out;
+	}
+
+	err = 0;
+	if (a->dst_btop != a->btgt)
+		goto out;
+
+	err = -ENOTEMPTY;
+	if (unlikely(a->dst_h_dentry == a->h_trap))
+		goto out;
+
+	err = -EIO;
+	isdir = !!au_ftest_ren(a->auren_flags, ISDIR_DST);
+	if (d_really_is_negative(a->dst_dentry)) {
+		if (d_is_negative(a->dst_h_dentry))
+			err = au_may_add(a->dst_dentry, a->btgt,
+					 a->dst_h_parent, isdir);
+	} else {
+		if (unlikely(d_is_negative(a->dst_h_dentry)))
+			goto out;
+		h_inode = d_inode(a->dst_h_dentry);
+		if (h_inode->i_nlink)
+			err = au_may_del(a->dst_dentry, a->btgt,
+					 a->dst_h_parent, isdir);
+	}
+
+out:
+	if (unlikely(err == -ENOENT || err == -EEXIST))
+		err = -EIO;
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * locking order
+ * (VFS)
+ * - src_dir and dir by lock_rename()
+ * - inode if exists
+ * (aufs)
+ * - lock all
+ *   + src_dentry and dentry by aufs_read_and_write_lock2() which calls,
+ *     + si_read_lock
+ *     + di_write_lock2_child()
+ *       + di_write_lock_child()
+ *	   + ii_write_lock_child()
+ *       + di_write_lock_child2()
+ *	   + ii_write_lock_child2()
+ *     + src_parent and parent
+ *       + di_write_lock_parent()
+ *	   + ii_write_lock_parent()
+ *       + di_write_lock_parent2()
+ *	   + ii_write_lock_parent2()
+ *   + lower src_dir and dir by vfsub_lock_rename()
+ *   + verify the every relationships between child and parent. if any
+ *     of them failed, unlock all and return -EBUSY.
+ */
+static void au_ren_unlock(struct au_ren_args *a)
+{
+	vfsub_unlock_rename(a->src_h_parent, a->src_hdir,
+			    a->dst_h_parent, a->dst_hdir);
+	if (au_ftest_ren(a->auren_flags, DIRREN)
+	    && a->h_root)
+		au_hn_inode_unlock(a->h_root);
+	if (au_ftest_ren(a->auren_flags, MNT_WRITE))
+		vfsub_mnt_drop_write(au_br_mnt(a->br));
+}
+
+static int au_ren_lock(struct au_ren_args *a)
+{
+	int err;
+	unsigned int udba;
+
+	err = 0;
+	a->src_h_parent = au_h_dptr(a->src_parent, a->btgt);
+	a->src_hdir = au_hi(a->src_dir, a->btgt);
+	a->dst_h_parent = au_h_dptr(a->dst_parent, a->btgt);
+	a->dst_hdir = au_hi(a->dst_dir, a->btgt);
+
+	err = vfsub_mnt_want_write(au_br_mnt(a->br));
+	if (unlikely(err))
+		goto out;
+	au_fset_ren(a->auren_flags, MNT_WRITE);
+	if (au_ftest_ren(a->auren_flags, DIRREN)) {
+		struct dentry *root;
+		struct inode *dir;
+
+		/*
+		 * sbinfo is already locked, so this ii_read_lock is
+		 * unnecessary. but our debugging feature checks it.
+		 */
+		root = a->src_inode->i_sb->s_root;
+		if (root != a->src_parent && root != a->dst_parent) {
+			dir = d_inode(root);
+			ii_read_lock_parent3(dir);
+			a->h_root = au_hi(dir, a->btgt);
+			ii_read_unlock(dir);
+			au_hn_inode_lock_nested(a->h_root, AuLsc_I_PARENT3);
+		}
+	}
+	a->h_trap = vfsub_lock_rename(a->src_h_parent, a->src_hdir,
+				      a->dst_h_parent, a->dst_hdir);
+	udba = au_opt_udba(a->src_dentry->d_sb);
+	if (unlikely(a->src_hdir->hi_inode != d_inode(a->src_h_parent)
+		     || a->dst_hdir->hi_inode != d_inode(a->dst_h_parent)))
+		err = au_busy_or_stale();
+	if (!err && au_dbtop(a->src_dentry) == a->btgt)
+		err = au_h_verify(a->src_h_dentry, udba,
+				  d_inode(a->src_h_parent), a->src_h_parent,
+				  a->br);
+	if (!err && au_dbtop(a->dst_dentry) == a->btgt)
+		err = au_h_verify(a->dst_h_dentry, udba,
+				  d_inode(a->dst_h_parent), a->dst_h_parent,
+				  a->br);
+	if (!err)
+		goto out; /* success */
+
+	err = au_busy_or_stale();
+	au_ren_unlock(a);
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static void au_ren_refresh_dir(struct au_ren_args *a)
+{
+	struct inode *dir;
+
+	dir = a->dst_dir;
+	inode_inc_iversion(dir);
+	if (au_ftest_ren(a->auren_flags, ISDIR_SRC)) {
+		/* is this updating defined in POSIX? */
+		au_cpup_attr_timesizes(a->src_inode);
+		au_cpup_attr_nlink(dir, /*force*/1);
+	}
+	au_dir_ts(dir, a->btgt);
+
+	if (a->exchange) {
+		dir = a->src_dir;
+		inode_inc_iversion(dir);
+		if (au_ftest_ren(a->auren_flags, ISDIR_DST)) {
+			/* is this updating defined in POSIX? */
+			au_cpup_attr_timesizes(a->dst_inode);
+			au_cpup_attr_nlink(dir, /*force*/1);
+		}
+		au_dir_ts(dir, a->btgt);
+	}
+
+	if (au_ftest_ren(a->auren_flags, ISSAMEDIR))
+		return;
+
+	dir = a->src_dir;
+	inode_inc_iversion(dir);
+	if (au_ftest_ren(a->auren_flags, ISDIR_SRC))
+		au_cpup_attr_nlink(dir, /*force*/1);
+	au_dir_ts(dir, a->btgt);
+}
+
+static void au_ren_refresh(struct au_ren_args *a)
+{
+	aufs_bindex_t bbot, bindex;
+	struct dentry *d, *h_d;
+	struct inode *i, *h_i;
+	struct super_block *sb;
+
+	d = a->dst_dentry;
+	d_drop(d);
+	if (a->h_dst)
+		/* already dget-ed by au_ren_or_cpup() */
+		au_set_h_dptr(d, a->btgt, a->h_dst);
+
+	i = a->dst_inode;
+	if (i) {
+		if (!a->exchange) {
+			if (!au_ftest_ren(a->auren_flags, ISDIR_DST))
+				vfsub_drop_nlink(i);
+			else {
+				vfsub_dead_dir(i);
+				au_cpup_attr_timesizes(i);
+			}
+			au_update_dbrange(d, /*do_put_zero*/1);
+		} else
+			au_cpup_attr_nlink(i, /*force*/1);
+	} else {
+		bbot = a->btgt;
+		for (bindex = au_dbtop(d); bindex < bbot; bindex++)
+			au_set_h_dptr(d, bindex, NULL);
+		bbot = au_dbbot(d);
+		for (bindex = a->btgt + 1; bindex <= bbot; bindex++)
+			au_set_h_dptr(d, bindex, NULL);
+		au_update_dbrange(d, /*do_put_zero*/0);
+	}
+
+	if (a->exchange
+	    || au_ftest_ren(a->auren_flags, DIRREN)) {
+		d_drop(a->src_dentry);
+		if (au_ftest_ren(a->auren_flags, DIRREN))
+			au_set_dbwh(a->src_dentry, -1);
+		return;
+	}
+
+	d = a->src_dentry;
+	au_set_dbwh(d, -1);
+	bbot = au_dbbot(d);
+	for (bindex = a->btgt + 1; bindex <= bbot; bindex++) {
+		h_d = au_h_dptr(d, bindex);
+		if (h_d)
+			au_set_h_dptr(d, bindex, NULL);
+	}
+	au_set_dbbot(d, a->btgt);
+
+	sb = d->d_sb;
+	i = a->src_inode;
+	if (au_opt_test(au_mntflags(sb), PLINK) && au_plink_test(i))
+		return; /* success */
+
+	bbot = au_ibbot(i);
+	for (bindex = a->btgt + 1; bindex <= bbot; bindex++) {
+		h_i = au_h_iptr(i, bindex);
+		if (h_i) {
+			au_xino_write(sb, bindex, h_i->i_ino, /*ino*/0);
+			/* ignore this error */
+			au_set_h_iptr(i, bindex, NULL, 0);
+		}
+	}
+	au_set_ibbot(i, a->btgt);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* mainly for link(2) and rename(2) */
+int au_wbr(struct dentry *dentry, aufs_bindex_t btgt)
+{
+	aufs_bindex_t bdiropq, bwh;
+	struct dentry *parent;
+	struct au_branch *br;
+
+	parent = dentry->d_parent;
+	IMustLock(d_inode(parent)); /* dir is locked */
+
+	bdiropq = au_dbdiropq(parent);
+	bwh = au_dbwh(dentry);
+	br = au_sbr(dentry->d_sb, btgt);
+	if (au_br_rdonly(br)
+	    || (0 <= bdiropq && bdiropq < btgt)
+	    || (0 <= bwh && bwh < btgt))
+		btgt = -1;
+
+	AuDbg("btgt %d\n", btgt);
+	return btgt;
+}
+
+/* sets src_btop, dst_btop and btgt */
+static int au_ren_wbr(struct au_ren_args *a)
+{
+	int err;
+	struct au_wr_dir_args wr_dir_args = {
+		/* .force_btgt	= -1, */
+		.flags		= AuWrDir_ADD_ENTRY
+	};
+
+	a->src_btop = au_dbtop(a->src_dentry);
+	a->dst_btop = au_dbtop(a->dst_dentry);
+	if (au_ftest_ren(a->auren_flags, ISDIR_SRC)
+	    || au_ftest_ren(a->auren_flags, ISDIR_DST))
+		au_fset_wrdir(wr_dir_args.flags, ISDIR);
+	wr_dir_args.force_btgt = a->src_btop;
+	if (a->dst_inode && a->dst_btop < a->src_btop)
+		wr_dir_args.force_btgt = a->dst_btop;
+	wr_dir_args.force_btgt = au_wbr(a->dst_dentry, wr_dir_args.force_btgt);
+	err = au_wr_dir(a->dst_dentry, a->src_dentry, &wr_dir_args);
+	a->btgt = err;
+	if (a->exchange)
+		au_update_dbtop(a->dst_dentry);
+
+	return err;
+}
+
+static void au_ren_dt(struct au_ren_args *a)
+{
+	a->h_path.dentry = a->src_h_parent;
+	au_dtime_store(a->src_dt + AuPARENT, a->src_parent, &a->h_path);
+	if (!au_ftest_ren(a->auren_flags, ISSAMEDIR)) {
+		a->h_path.dentry = a->dst_h_parent;
+		au_dtime_store(a->dst_dt + AuPARENT, a->dst_parent, &a->h_path);
+	}
+
+	au_fclr_ren(a->auren_flags, DT_DSTDIR);
+	if (!au_ftest_ren(a->auren_flags, ISDIR_SRC)
+	    && !a->exchange)
+		return;
+
+	a->h_path.dentry = a->src_h_dentry;
+	au_dtime_store(a->src_dt + AuCHILD, a->src_dentry, &a->h_path);
+	if (d_is_positive(a->dst_h_dentry)) {
+		au_fset_ren(a->auren_flags, DT_DSTDIR);
+		a->h_path.dentry = a->dst_h_dentry;
+		au_dtime_store(a->dst_dt + AuCHILD, a->dst_dentry, &a->h_path);
+	}
+}
+
+static void au_ren_rev_dt(int err, struct au_ren_args *a)
+{
+	struct dentry *h_d;
+	struct inode *h_inode;
+
+	au_dtime_revert(a->src_dt + AuPARENT);
+	if (!au_ftest_ren(a->auren_flags, ISSAMEDIR))
+		au_dtime_revert(a->dst_dt + AuPARENT);
+
+	if (au_ftest_ren(a->auren_flags, ISDIR_SRC) && err != -EIO) {
+		h_d = a->src_dt[AuCHILD].dt_h_path.dentry;
+		h_inode = d_inode(h_d);
+		inode_lock_nested(h_inode, AuLsc_I_CHILD);
+		au_dtime_revert(a->src_dt + AuCHILD);
+		inode_unlock(h_inode);
+
+		if (au_ftest_ren(a->auren_flags, DT_DSTDIR)) {
+			h_d = a->dst_dt[AuCHILD].dt_h_path.dentry;
+			h_inode = d_inode(h_d);
+			inode_lock_nested(h_inode, AuLsc_I_CHILD);
+			au_dtime_revert(a->dst_dt + AuCHILD);
+			inode_unlock(h_inode);
+		}
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+int aufs_rename(struct user_namespace *userns,
+		struct inode *_src_dir, struct dentry *_src_dentry,
+		struct inode *_dst_dir, struct dentry *_dst_dentry,
+		unsigned int _flags)
+{
+	int err, lock_flags;
+	void *rev;
+	/* reduce stack space */
+	struct au_ren_args *a;
+	struct au_pin pin;
+
+	AuDbg("%pd, %pd, 0x%x\n", _src_dentry, _dst_dentry, _flags);
+	IMustLock(_src_dir);
+	IMustLock(_dst_dir);
+
+	err = -EINVAL;
+	if (unlikely(_flags & RENAME_WHITEOUT))
+		goto out;
+
+	err = -ENOMEM;
+	BUILD_BUG_ON(sizeof(*a) > PAGE_SIZE);
+	a = kzalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	a->flags = _flags;
+	BUILD_BUG_ON(sizeof(a->exchange) == sizeof(u8)
+		     && RENAME_EXCHANGE > U8_MAX);
+	a->exchange = _flags & RENAME_EXCHANGE;
+	a->src_dir = _src_dir;
+	a->src_dentry = _src_dentry;
+	a->src_inode = NULL;
+	if (d_really_is_positive(a->src_dentry))
+		a->src_inode = d_inode(a->src_dentry);
+	a->src_parent = a->src_dentry->d_parent; /* dir inode is locked */
+	a->dst_dir = _dst_dir;
+	a->dst_dentry = _dst_dentry;
+	a->dst_inode = NULL;
+	if (d_really_is_positive(a->dst_dentry))
+		a->dst_inode = d_inode(a->dst_dentry);
+	a->dst_parent = a->dst_dentry->d_parent; /* dir inode is locked */
+	if (a->dst_inode) {
+		/*
+		 * if EXCHANGE && src is non-dir && dst is dir,
+		 * dst is not locked.
+		 */
+		/* IMustLock(a->dst_inode); */
+		au_igrab(a->dst_inode);
+	}
+
+	err = -ENOTDIR;
+	lock_flags = AuLock_FLUSH | AuLock_NOPLM | AuLock_GEN;
+	if (d_is_dir(a->src_dentry)) {
+		au_fset_ren(a->auren_flags, ISDIR_SRC);
+		if (unlikely(!a->exchange
+			     && d_really_is_positive(a->dst_dentry)
+			     && !d_is_dir(a->dst_dentry)))
+			goto out_free;
+		lock_flags |= AuLock_DIRS;
+	}
+	if (a->dst_inode && d_is_dir(a->dst_dentry)) {
+		au_fset_ren(a->auren_flags, ISDIR_DST);
+		if (unlikely(!a->exchange
+			     && d_really_is_positive(a->src_dentry)
+			     && !d_is_dir(a->src_dentry)))
+			goto out_free;
+		lock_flags |= AuLock_DIRS;
+	}
+	err = aufs_read_and_write_lock2(a->dst_dentry, a->src_dentry,
+					lock_flags);
+	if (unlikely(err))
+		goto out_free;
+
+	err = au_d_hashed_positive(a->src_dentry);
+	if (unlikely(err))
+		goto out_unlock;
+	err = -ENOENT;
+	if (a->dst_inode) {
+		/*
+		 * If it is a dir, VFS unhash it before this
+		 * function. It means we cannot rely upon d_unhashed().
+		 */
+		if (unlikely(!a->dst_inode->i_nlink))
+			goto out_unlock;
+		if (!au_ftest_ren(a->auren_flags, ISDIR_DST)) {
+			err = au_d_hashed_positive(a->dst_dentry);
+			if (unlikely(err && !a->exchange))
+				goto out_unlock;
+		} else if (unlikely(IS_DEADDIR(a->dst_inode)))
+			goto out_unlock;
+	} else if (unlikely(d_unhashed(a->dst_dentry)))
+		goto out_unlock;
+
+	/*
+	 * is it possible?
+	 * yes, it happened (in linux-3.3-rcN) but I don't know why.
+	 * there may exist a problem somewhere else.
+	 */
+	err = -EINVAL;
+	if (unlikely(d_inode(a->dst_parent) == d_inode(a->src_dentry)))
+		goto out_unlock;
+
+	au_fset_ren(a->auren_flags, ISSAMEDIR); /* temporary */
+	di_write_lock_parent(a->dst_parent);
+
+	/* which branch we process */
+	err = au_ren_wbr(a);
+	if (unlikely(err < 0))
+		goto out_parent;
+	a->br = au_sbr(a->dst_dentry->d_sb, a->btgt);
+	a->h_path.mnt = au_br_mnt(a->br);
+
+	/* are they available to be renamed */
+	err = au_ren_may_dir(a);
+	if (unlikely(err))
+		goto out_children;
+
+	/* prepare the writable parent dir on the same branch */
+	if (a->dst_btop == a->btgt) {
+		au_fset_ren(a->auren_flags, WHDST);
+	} else {
+		err = au_cpup_dirs(a->dst_dentry, a->btgt);
+		if (unlikely(err))
+			goto out_children;
+	}
+
+	err = 0;
+	if (!a->exchange) {
+		if (a->src_dir != a->dst_dir) {
+			/*
+			 * this temporary unlock is safe,
+			 * because both dir->i_mutex are locked.
+			 */
+			di_write_unlock(a->dst_parent);
+			di_write_lock_parent(a->src_parent);
+			err = au_wr_dir_need_wh(a->src_dentry,
+						au_ftest_ren(a->auren_flags,
+							     ISDIR_SRC),
+						&a->btgt);
+			di_write_unlock(a->src_parent);
+			di_write_lock2_parent(a->src_parent, a->dst_parent,
+					      /*isdir*/1);
+			au_fclr_ren(a->auren_flags, ISSAMEDIR);
+		} else
+			err = au_wr_dir_need_wh(a->src_dentry,
+						au_ftest_ren(a->auren_flags,
+							     ISDIR_SRC),
+						&a->btgt);
+	}
+	if (unlikely(err < 0))
+		goto out_children;
+	if (err)
+		au_fset_ren(a->auren_flags, WHSRC);
+
+	/* cpup src */
+	if (a->src_btop != a->btgt) {
+		err = au_pin(&pin, a->src_dentry, a->btgt,
+			     au_opt_udba(a->src_dentry->d_sb),
+			     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+		if (!err) {
+			struct au_cp_generic cpg = {
+				.dentry	= a->src_dentry,
+				.bdst	= a->btgt,
+				.bsrc	= a->src_btop,
+				.len	= -1,
+				.pin	= &pin,
+				.flags	= AuCpup_DTIME | AuCpup_HOPEN
+			};
+			AuDebugOn(au_dbtop(a->src_dentry) != a->src_btop);
+			err = au_sio_cpup_simple(&cpg);
+			au_unpin(&pin);
+		}
+		if (unlikely(err))
+			goto out_children;
+		a->src_btop = a->btgt;
+		a->src_h_dentry = au_h_dptr(a->src_dentry, a->btgt);
+		if (!a->exchange)
+			au_fset_ren(a->auren_flags, WHSRC);
+	}
+
+	/* cpup dst */
+	if (a->exchange && a->dst_inode
+	    && a->dst_btop != a->btgt) {
+		err = au_pin(&pin, a->dst_dentry, a->btgt,
+			     au_opt_udba(a->dst_dentry->d_sb),
+			     AuPin_DI_LOCKED | AuPin_MNT_WRITE);
+		if (!err) {
+			struct au_cp_generic cpg = {
+				.dentry	= a->dst_dentry,
+				.bdst	= a->btgt,
+				.bsrc	= a->dst_btop,
+				.len	= -1,
+				.pin	= &pin,
+				.flags	= AuCpup_DTIME | AuCpup_HOPEN
+			};
+			err = au_sio_cpup_simple(&cpg);
+			au_unpin(&pin);
+		}
+		if (unlikely(err))
+			goto out_children;
+		a->dst_btop = a->btgt;
+		a->dst_h_dentry = au_h_dptr(a->dst_dentry, a->btgt);
+	}
+
+	/* lock them all */
+	err = au_ren_lock(a);
+	if (unlikely(err))
+		/* leave the copied-up one */
+		goto out_children;
+
+	if (!a->exchange) {
+		if (!au_opt_test(au_mntflags(a->dst_dir->i_sb), UDBA_NONE))
+			err = au_may_ren(a);
+		else if (unlikely(a->dst_dentry->d_name.len > AUFS_MAX_NAMELEN))
+			err = -ENAMETOOLONG;
+		if (unlikely(err))
+			goto out_hdir;
+	}
+
+	/* store timestamps to be revertible */
+	au_ren_dt(a);
+
+	/* store dirren info */
+	if (au_ftest_ren(a->auren_flags, DIRREN)) {
+		err = au_dr_rename(a->src_dentry, a->btgt,
+				   &a->dst_dentry->d_name, &rev);
+		AuTraceErr(err);
+		if (unlikely(err))
+			goto out_dt;
+	}
+
+	/* here we go */
+	err = do_rename(a);
+	if (unlikely(err))
+		goto out_dirren;
+
+	if (au_ftest_ren(a->auren_flags, DIRREN))
+		au_dr_rename_fin(a->src_dentry, a->btgt, rev);
+
+	/* update dir attributes */
+	au_ren_refresh_dir(a);
+
+	/* dput/iput all lower dentries */
+	au_ren_refresh(a);
+
+	goto out_hdir; /* success */
+
+out_dirren:
+	if (au_ftest_ren(a->auren_flags, DIRREN))
+		au_dr_rename_rev(a->src_dentry, a->btgt, rev);
+out_dt:
+	au_ren_rev_dt(err, a);
+out_hdir:
+	au_ren_unlock(a);
+out_children:
+	au_nhash_wh_free(&a->whlist);
+	if (err && a->dst_inode && a->dst_btop != a->btgt) {
+		AuDbg("btop %d, btgt %d\n", a->dst_btop, a->btgt);
+		au_set_h_dptr(a->dst_dentry, a->btgt, NULL);
+		au_set_dbtop(a->dst_dentry, a->dst_btop);
+	}
+out_parent:
+	if (!err) {
+		if (d_unhashed(a->src_dentry))
+			au_fset_ren(a->auren_flags, DROPPED_SRC);
+		if (d_unhashed(a->dst_dentry))
+			au_fset_ren(a->auren_flags, DROPPED_DST);
+		if (!a->exchange)
+			d_move(a->src_dentry, a->dst_dentry);
+		else {
+			d_exchange(a->src_dentry, a->dst_dentry);
+			if (au_ftest_ren(a->auren_flags, DROPPED_DST))
+				d_drop(a->dst_dentry);
+		}
+		if (au_ftest_ren(a->auren_flags, DROPPED_SRC))
+			d_drop(a->src_dentry);
+	} else {
+		au_update_dbtop(a->dst_dentry);
+		if (!a->dst_inode)
+			d_drop(a->dst_dentry);
+	}
+	if (au_ftest_ren(a->auren_flags, ISSAMEDIR))
+		di_write_unlock(a->dst_parent);
+	else
+		di_write_unlock2(a->src_parent, a->dst_parent);
+out_unlock:
+	aufs_read_and_write_unlock2(a->dst_dentry, a->src_dentry);
+out_free:
+	iput(a->dst_inode);
+	if (a->thargs)
+		au_whtmp_rmdir_free(a->thargs);
+	au_kfree_rcu(a);
+out:
+	AuTraceErr(err);
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/iinfo.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/iinfo.c
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode private data
+ */
+
+#include "aufs.h"
+
+struct inode *au_h_iptr(struct inode *inode, aufs_bindex_t bindex)
+{
+	struct inode *h_inode;
+	struct au_hinode *hinode;
+
+	IiMustAnyLock(inode);
+
+	hinode = au_hinode(au_ii(inode), bindex);
+	h_inode = hinode->hi_inode;
+	AuDebugOn(h_inode && atomic_read(&h_inode->i_count) <= 0);
+	return h_inode;
+}
+
+/* todo: hard/soft set? */
+void au_hiput(struct au_hinode *hinode)
+{
+	au_hn_free(hinode);
+	dput(hinode->hi_whdentry);
+	iput(hinode->hi_inode);
+}
+
+unsigned int au_hi_flags(struct inode *inode, int isdir)
+{
+	unsigned int flags;
+	const unsigned int mnt_flags = au_mntflags(inode->i_sb);
+
+	flags = 0;
+	if (au_opt_test(mnt_flags, XINO))
+		au_fset_hi(flags, XINO);
+	if (isdir && au_opt_test(mnt_flags, UDBA_HNOTIFY))
+		au_fset_hi(flags, HNOTIFY);
+	return flags;
+}
+
+void au_set_h_iptr(struct inode *inode, aufs_bindex_t bindex,
+		   struct inode *h_inode, unsigned int flags)
+{
+	struct au_hinode *hinode;
+	struct inode *hi;
+	struct au_iinfo *iinfo = au_ii(inode);
+
+	IiMustWriteLock(inode);
+
+	hinode = au_hinode(iinfo, bindex);
+	hi = hinode->hi_inode;
+	AuDebugOn(h_inode && atomic_read(&h_inode->i_count) <= 0);
+
+	if (hi)
+		au_hiput(hinode);
+	hinode->hi_inode = h_inode;
+	if (h_inode) {
+		int err;
+		struct super_block *sb = inode->i_sb;
+		struct au_branch *br;
+
+		AuDebugOn(inode->i_mode
+			  && (h_inode->i_mode & S_IFMT)
+			  != (inode->i_mode & S_IFMT));
+		if (bindex == iinfo->ii_btop)
+			au_cpup_igen(inode, h_inode);
+		br = au_sbr(sb, bindex);
+		hinode->hi_id = br->br_id;
+		if (au_ftest_hi(flags, XINO)) {
+			err = au_xino_write(sb, bindex, h_inode->i_ino,
+					    inode->i_ino);
+			if (unlikely(err))
+				AuIOErr1("failed au_xino_write() %d\n", err);
+		}
+
+		if (au_ftest_hi(flags, HNOTIFY)
+		    && au_br_hnotifyable(br->br_perm)) {
+			err = au_hn_alloc(hinode, inode);
+			if (unlikely(err))
+				AuIOErr1("au_hn_alloc() %d\n", err);
+		}
+	}
+}
+
+void au_set_hi_wh(struct inode *inode, aufs_bindex_t bindex,
+		  struct dentry *h_wh)
+{
+	struct au_hinode *hinode;
+
+	IiMustWriteLock(inode);
+
+	hinode = au_hinode(au_ii(inode), bindex);
+	AuDebugOn(hinode->hi_whdentry);
+	hinode->hi_whdentry = h_wh;
+}
+
+void au_update_iigen(struct inode *inode, int half)
+{
+	struct au_iinfo *iinfo;
+	struct au_iigen *iigen;
+	unsigned int sigen;
+
+	sigen = au_sigen(inode->i_sb);
+	iinfo = au_ii(inode);
+	iigen = &iinfo->ii_generation;
+	spin_lock(&iigen->ig_spin);
+	iigen->ig_generation = sigen;
+	if (half)
+		au_ig_fset(iigen->ig_flags, HALF_REFRESHED);
+	else
+		au_ig_fclr(iigen->ig_flags, HALF_REFRESHED);
+	spin_unlock(&iigen->ig_spin);
+}
+
+/* it may be called at remount time, too */
+void au_update_ibrange(struct inode *inode, int do_put_zero)
+{
+	struct au_iinfo *iinfo;
+	aufs_bindex_t bindex, bbot;
+
+	AuDebugOn(au_is_bad_inode(inode));
+	IiMustWriteLock(inode);
+
+	iinfo = au_ii(inode);
+	if (do_put_zero && iinfo->ii_btop >= 0) {
+		for (bindex = iinfo->ii_btop; bindex <= iinfo->ii_bbot;
+		     bindex++) {
+			struct inode *h_i;
+
+			h_i = au_hinode(iinfo, bindex)->hi_inode;
+			if (h_i
+			    && !h_i->i_nlink
+			    && !(h_i->i_state & I_LINKABLE))
+				au_set_h_iptr(inode, bindex, NULL, 0);
+		}
+	}
+
+	iinfo->ii_btop = -1;
+	iinfo->ii_bbot = -1;
+	bbot = au_sbbot(inode->i_sb);
+	for (bindex = 0; bindex <= bbot; bindex++)
+		if (au_hinode(iinfo, bindex)->hi_inode) {
+			iinfo->ii_btop = bindex;
+			break;
+		}
+	if (iinfo->ii_btop >= 0)
+		for (bindex = bbot; bindex >= iinfo->ii_btop; bindex--)
+			if (au_hinode(iinfo, bindex)->hi_inode) {
+				iinfo->ii_bbot = bindex;
+				break;
+			}
+	AuDebugOn(iinfo->ii_btop > iinfo->ii_bbot);
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_icntnr_init_once(void *_c)
+{
+	struct au_icntnr *c = _c;
+	struct au_iinfo *iinfo = &c->iinfo;
+
+	spin_lock_init(&iinfo->ii_generation.ig_spin);
+	au_rw_init(&iinfo->ii_rwsem);
+	inode_init_once(&c->vfs_inode);
+}
+
+void au_hinode_init(struct au_hinode *hinode)
+{
+	hinode->hi_inode = NULL;
+	hinode->hi_id = -1;
+	au_hn_init(hinode);
+	hinode->hi_whdentry = NULL;
+}
+
+int au_iinfo_init(struct inode *inode)
+{
+	struct au_iinfo *iinfo;
+	struct super_block *sb;
+	struct au_hinode *hi;
+	int nbr, i;
+
+	sb = inode->i_sb;
+	iinfo = &(container_of(inode, struct au_icntnr, vfs_inode)->iinfo);
+	nbr = au_sbbot(sb) + 1;
+	if (unlikely(nbr <= 0))
+		nbr = 1;
+	hi = kmalloc_array(nbr, sizeof(*iinfo->ii_hinode), GFP_NOFS);
+	if (hi) {
+		au_lcnt_inc(&au_sbi(sb)->si_ninodes);
+
+		iinfo->ii_hinode = hi;
+		for (i = 0; i < nbr; i++, hi++)
+			au_hinode_init(hi);
+
+		iinfo->ii_generation.ig_generation = au_sigen(sb);
+		iinfo->ii_btop = -1;
+		iinfo->ii_bbot = -1;
+		iinfo->ii_vdir = NULL;
+		return 0;
+	}
+	return -ENOMEM;
+}
+
+int au_hinode_realloc(struct au_iinfo *iinfo, int nbr, int may_shrink)
+{
+	int err, i;
+	struct au_hinode *hip;
+
+	AuRwMustWriteLock(&iinfo->ii_rwsem);
+
+	err = -ENOMEM;
+	hip = au_krealloc(iinfo->ii_hinode, sizeof(*hip) * nbr, GFP_NOFS,
+			  may_shrink);
+	if (hip) {
+		iinfo->ii_hinode = hip;
+		i = iinfo->ii_bbot + 1;
+		hip += i;
+		for (; i < nbr; i++, hip++)
+			au_hinode_init(hip);
+		err = 0;
+	}
+
+	return err;
+}
+
+void au_iinfo_fin(struct inode *inode)
+{
+	struct au_iinfo *iinfo;
+	struct au_hinode *hi;
+	struct super_block *sb;
+	aufs_bindex_t bindex, bbot;
+	const unsigned char unlinked = !inode->i_nlink;
+
+	AuDebugOn(au_is_bad_inode(inode));
+
+	sb = inode->i_sb;
+	au_lcnt_dec(&au_sbi(sb)->si_ninodes);
+	if (si_pid_test(sb))
+		au_xino_delete_inode(inode, unlinked);
+	else {
+		/*
+		 * it is safe to hide the dependency between sbinfo and
+		 * sb->s_umount.
+		 */
+		lockdep_off();
+		si_noflush_read_lock(sb);
+		au_xino_delete_inode(inode, unlinked);
+		si_read_unlock(sb);
+		lockdep_on();
+	}
+
+	iinfo = au_ii(inode);
+	if (iinfo->ii_vdir)
+		au_vdir_free(iinfo->ii_vdir);
+
+	bindex = iinfo->ii_btop;
+	if (bindex >= 0) {
+		hi = au_hinode(iinfo, bindex);
+		bbot = iinfo->ii_bbot;
+		while (bindex++ <= bbot) {
+			if (hi->hi_inode)
+				au_hiput(hi);
+			hi++;
+		}
+	}
+	au_kfree_rcu(iinfo->ii_hinode);
+	AuRwDestroy(&iinfo->ii_rwsem);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/inode.c
@@ -0,0 +1,531 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode functions
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+struct inode *au_igrab(struct inode *inode)
+{
+	if (inode) {
+		AuDebugOn(!atomic_read(&inode->i_count));
+		ihold(inode);
+	}
+	return inode;
+}
+
+static void au_refresh_hinode_attr(struct inode *inode, int do_version)
+{
+	au_cpup_attr_all(inode, /*force*/0);
+	au_update_iigen(inode, /*half*/1);
+	if (do_version)
+		inode_inc_iversion(inode);
+}
+
+static int au_ii_refresh(struct inode *inode, int *update)
+{
+	int err, e, nbr;
+	umode_t type;
+	aufs_bindex_t bindex, new_bindex;
+	struct super_block *sb;
+	struct au_iinfo *iinfo;
+	struct au_hinode *p, *q, tmp;
+
+	AuDebugOn(au_is_bad_inode(inode));
+	IiMustWriteLock(inode);
+
+	*update = 0;
+	sb = inode->i_sb;
+	nbr = au_sbbot(sb) + 1;
+	type = inode->i_mode & S_IFMT;
+	iinfo = au_ii(inode);
+	err = au_hinode_realloc(iinfo, nbr, /*may_shrink*/0);
+	if (unlikely(err))
+		goto out;
+
+	AuDebugOn(iinfo->ii_btop < 0);
+	p = au_hinode(iinfo, iinfo->ii_btop);
+	for (bindex = iinfo->ii_btop; bindex <= iinfo->ii_bbot;
+	     bindex++, p++) {
+		if (!p->hi_inode)
+			continue;
+
+		AuDebugOn(type != (p->hi_inode->i_mode & S_IFMT));
+		new_bindex = au_br_index(sb, p->hi_id);
+		if (new_bindex == bindex)
+			continue;
+
+		if (new_bindex < 0) {
+			*update = 1;
+			au_hiput(p);
+			p->hi_inode = NULL;
+			continue;
+		}
+
+		if (new_bindex < iinfo->ii_btop)
+			iinfo->ii_btop = new_bindex;
+		if (iinfo->ii_bbot < new_bindex)
+			iinfo->ii_bbot = new_bindex;
+		/* swap two lower inode, and loop again */
+		q = au_hinode(iinfo, new_bindex);
+		tmp = *q;
+		*q = *p;
+		*p = tmp;
+		if (tmp.hi_inode) {
+			bindex--;
+			p--;
+		}
+	}
+	au_update_ibrange(inode, /*do_put_zero*/0);
+	au_hinode_realloc(iinfo, nbr, /*may_shrink*/1); /* harmless if err */
+	e = au_dy_irefresh(inode);
+	if (unlikely(e && !err))
+		err = e;
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+void au_refresh_iop(struct inode *inode, int force_getattr)
+{
+	int type;
+	struct au_sbinfo *sbi = au_sbi(inode->i_sb);
+	const struct inode_operations *iop
+		= force_getattr ? aufs_iop : sbi->si_iop_array;
+
+	if (inode->i_op == iop)
+		return;
+
+	switch (inode->i_mode & S_IFMT) {
+	case S_IFDIR:
+		type = AuIop_DIR;
+		break;
+	case S_IFLNK:
+		type = AuIop_SYMLINK;
+		break;
+	default:
+		type = AuIop_OTHER;
+		break;
+	}
+
+	inode->i_op = iop + type;
+	/* unnecessary smp_wmb() */
+}
+
+int au_refresh_hinode_self(struct inode *inode)
+{
+	int err, update;
+
+	err = au_ii_refresh(inode, &update);
+	if (!err)
+		au_refresh_hinode_attr(inode, update && S_ISDIR(inode->i_mode));
+
+	AuTraceErr(err);
+	return err;
+}
+
+int au_refresh_hinode(struct inode *inode, struct dentry *dentry)
+{
+	int err, e, update;
+	unsigned int flags;
+	umode_t mode;
+	aufs_bindex_t bindex, bbot;
+	unsigned char isdir;
+	struct au_hinode *p;
+	struct au_iinfo *iinfo;
+
+	err = au_ii_refresh(inode, &update);
+	if (unlikely(err))
+		goto out;
+
+	update = 0;
+	iinfo = au_ii(inode);
+	p = au_hinode(iinfo, iinfo->ii_btop);
+	mode = (inode->i_mode & S_IFMT);
+	isdir = S_ISDIR(mode);
+	flags = au_hi_flags(inode, isdir);
+	bbot = au_dbbot(dentry);
+	for (bindex = au_dbtop(dentry); bindex <= bbot; bindex++) {
+		struct inode *h_i, *h_inode;
+		struct dentry *h_d;
+
+		h_d = au_h_dptr(dentry, bindex);
+		if (!h_d || d_is_negative(h_d))
+			continue;
+
+		h_inode = d_inode(h_d);
+		AuDebugOn(mode != (h_inode->i_mode & S_IFMT));
+		if (iinfo->ii_btop <= bindex && bindex <= iinfo->ii_bbot) {
+			h_i = au_h_iptr(inode, bindex);
+			if (h_i) {
+				if (h_i == h_inode)
+					continue;
+				err = -EIO;
+				break;
+			}
+		}
+		if (bindex < iinfo->ii_btop)
+			iinfo->ii_btop = bindex;
+		if (iinfo->ii_bbot < bindex)
+			iinfo->ii_bbot = bindex;
+		au_set_h_iptr(inode, bindex, au_igrab(h_inode), flags);
+		update = 1;
+	}
+	au_update_ibrange(inode, /*do_put_zero*/0);
+	e = au_dy_irefresh(inode);
+	if (unlikely(e && !err))
+		err = e;
+	if (!err)
+		au_refresh_hinode_attr(inode, update && isdir);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int set_inode(struct inode *inode, struct dentry *dentry)
+{
+	int err;
+	unsigned int flags;
+	umode_t mode;
+	aufs_bindex_t bindex, btop, btail;
+	unsigned char isdir;
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+	struct au_iinfo *iinfo;
+	const struct inode_operations *iop;
+
+	IiMustWriteLock(inode);
+
+	err = 0;
+	isdir = 0;
+	iop = au_sbi(inode->i_sb)->si_iop_array;
+	btop = au_dbtop(dentry);
+	h_dentry = au_h_dptr(dentry, btop);
+	h_inode = d_inode(h_dentry);
+	mode = h_inode->i_mode;
+	switch (mode & S_IFMT) {
+	case S_IFREG:
+		btail = au_dbtail(dentry);
+		inode->i_op = iop + AuIop_OTHER;
+		inode->i_fop = &aufs_file_fop;
+		err = au_dy_iaop(inode, btop, h_inode);
+		if (unlikely(err))
+			goto out;
+		break;
+	case S_IFDIR:
+		isdir = 1;
+		btail = au_dbtaildir(dentry);
+		inode->i_op = iop + AuIop_DIR;
+		inode->i_fop = &aufs_dir_fop;
+		break;
+	case S_IFLNK:
+		btail = au_dbtail(dentry);
+		inode->i_op = iop + AuIop_SYMLINK;
+		break;
+	case S_IFBLK:
+	case S_IFCHR:
+	case S_IFIFO:
+	case S_IFSOCK:
+		btail = au_dbtail(dentry);
+		inode->i_op = iop + AuIop_OTHER;
+		init_special_inode(inode, mode, h_inode->i_rdev);
+		break;
+	default:
+		AuIOErr("Unknown file type 0%o\n", mode);
+		err = -EIO;
+		goto out;
+	}
+
+	/* do not set hnotify for whiteouted dirs (SHWH mode) */
+	flags = au_hi_flags(inode, isdir);
+	if (au_opt_test(au_mntflags(dentry->d_sb), SHWH)
+	    && au_ftest_hi(flags, HNOTIFY)
+	    && dentry->d_name.len > AUFS_WH_PFX_LEN
+	    && !memcmp(dentry->d_name.name, AUFS_WH_PFX, AUFS_WH_PFX_LEN))
+		au_fclr_hi(flags, HNOTIFY);
+	iinfo = au_ii(inode);
+	iinfo->ii_btop = btop;
+	iinfo->ii_bbot = btail;
+	for (bindex = btop; bindex <= btail; bindex++) {
+		h_dentry = au_h_dptr(dentry, bindex);
+		if (h_dentry)
+			au_set_h_iptr(inode, bindex,
+				      au_igrab(d_inode(h_dentry)), flags);
+	}
+	au_cpup_attr_all(inode, /*force*/1);
+	/*
+	 * to force calling aufs_get_acl() every time,
+	 * do not call cache_no_acl() for aufs inode.
+	 */
+
+out:
+	return err;
+}
+
+/*
+ * successful returns with iinfo write_locked
+ * minus: errno
+ * zero: success, matched
+ * plus: no error, but unmatched
+ */
+static int reval_inode(struct inode *inode, struct dentry *dentry)
+{
+	int err;
+	unsigned int gen, igflags;
+	aufs_bindex_t bindex, bbot;
+	struct inode *h_inode, *h_dinode;
+	struct dentry *h_dentry;
+
+	/*
+	 * before this function, if aufs got any iinfo lock, it must be only
+	 * one, the parent dir.
+	 * it can happen by UDBA and the obsoleted inode number.
+	 */
+	err = -EIO;
+	if (unlikely(inode->i_ino == parent_ino(dentry)))
+		goto out;
+
+	err = 1;
+	ii_write_lock_new_child(inode);
+	h_dentry = au_h_dptr(dentry, au_dbtop(dentry));
+	h_dinode = d_inode(h_dentry);
+	bbot = au_ibbot(inode);
+	for (bindex = au_ibtop(inode); bindex <= bbot; bindex++) {
+		h_inode = au_h_iptr(inode, bindex);
+		if (!h_inode || h_inode != h_dinode)
+			continue;
+
+		err = 0;
+		gen = au_iigen(inode, &igflags);
+		if (gen == au_digen(dentry)
+		    && !au_ig_ftest(igflags, HALF_REFRESHED))
+			break;
+
+		/* fully refresh inode using dentry */
+		err = au_refresh_hinode(inode, dentry);
+		if (!err)
+			au_update_iigen(inode, /*half*/0);
+		break;
+	}
+
+	if (unlikely(err))
+		ii_write_unlock(inode);
+out:
+	return err;
+}
+
+int au_ino(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+	   unsigned int d_type, ino_t *ino)
+{
+	int err, idx;
+	const int isnondir = d_type != DT_DIR;
+
+	/* prevent hardlinked inode number from race condition */
+	if (isnondir) {
+		err = au_xinondir_enter(sb, bindex, h_ino, &idx);
+		if (unlikely(err))
+			goto out;
+	}
+
+	err = au_xino_read(sb, bindex, h_ino, ino);
+	if (unlikely(err))
+		goto out_xinondir;
+
+	if (!*ino) {
+		err = -EIO;
+		*ino = au_xino_new_ino(sb);
+		if (unlikely(!*ino))
+			goto out_xinondir;
+		err = au_xino_write(sb, bindex, h_ino, *ino);
+		if (unlikely(err))
+			goto out_xinondir;
+	}
+
+out_xinondir:
+	if (isnondir && idx >= 0)
+		au_xinondir_leave(sb, bindex, h_ino, idx);
+out:
+	return err;
+}
+
+/* successful returns with iinfo write_locked */
+/* todo: return with unlocked? */
+struct inode *au_new_inode(struct dentry *dentry, int must_new)
+{
+	struct inode *inode, *h_inode;
+	struct dentry *h_dentry;
+	struct super_block *sb;
+	ino_t h_ino, ino;
+	int err, idx, hlinked;
+	aufs_bindex_t btop;
+
+	sb = dentry->d_sb;
+	btop = au_dbtop(dentry);
+	h_dentry = au_h_dptr(dentry, btop);
+	h_inode = d_inode(h_dentry);
+	h_ino = h_inode->i_ino;
+	hlinked = !d_is_dir(h_dentry) && h_inode->i_nlink > 1;
+
+new_ino:
+	/*
+	 * stop 'race'-ing between hardlinks under different
+	 * parents.
+	 */
+	if (hlinked) {
+		err = au_xinondir_enter(sb, btop, h_ino, &idx);
+		inode = ERR_PTR(err);
+		if (unlikely(err))
+			goto out;
+	}
+
+	err = au_xino_read(sb, btop, h_ino, &ino);
+	inode = ERR_PTR(err);
+	if (unlikely(err))
+		goto out_xinondir;
+
+	if (!ino) {
+		ino = au_xino_new_ino(sb);
+		if (unlikely(!ino)) {
+			inode = ERR_PTR(-EIO);
+			goto out_xinondir;
+		}
+	}
+
+	AuDbg("i%lu\n", (unsigned long)ino);
+	inode = au_iget_locked(sb, ino);
+	err = PTR_ERR(inode);
+	if (IS_ERR(inode))
+		goto out_xinondir;
+
+	AuDbg("%lx, new %d\n", inode->i_state, !!(inode->i_state & I_NEW));
+	if (inode->i_state & I_NEW) {
+		ii_write_lock_new_child(inode);
+		err = set_inode(inode, dentry);
+		if (!err) {
+			unlock_new_inode(inode);
+			goto out_xinondir; /* success */
+		}
+
+		/*
+		 * iget_failed() calls iput(), but we need to call
+		 * ii_write_unlock() after iget_failed(). so dirty hack for
+		 * i_count.
+		 */
+		atomic_inc(&inode->i_count);
+		iget_failed(inode);
+		ii_write_unlock(inode);
+		au_xino_write(sb, btop, h_ino, /*ino*/0);
+		/* ignore this error */
+		goto out_iput;
+	} else if (!must_new && !IS_DEADDIR(inode) && inode->i_nlink) {
+		/*
+		 * horrible race condition between lookup, readdir and copyup
+		 * (or something).
+		 */
+		if (hlinked && idx >= 0)
+			au_xinondir_leave(sb, btop, h_ino, idx);
+		err = reval_inode(inode, dentry);
+		if (unlikely(err < 0)) {
+			hlinked = 0;
+			goto out_iput;
+		}
+		if (!err)
+			goto out; /* success */
+		else if (hlinked && idx >= 0) {
+			err = au_xinondir_enter(sb, btop, h_ino, &idx);
+			if (unlikely(err)) {
+				iput(inode);
+				inode = ERR_PTR(err);
+				goto out;
+			}
+		}
+	}
+
+	if (unlikely(au_test_fs_unique_ino(h_inode)))
+		AuWarn1("Warning: Un-notified UDBA or repeatedly renamed dir,"
+			" b%d, %s, %pd, hi%lu, i%lu.\n",
+			btop, au_sbtype(h_dentry->d_sb), dentry,
+			(unsigned long)h_ino, (unsigned long)ino);
+	ino = 0;
+	err = au_xino_write(sb, btop, h_ino, /*ino*/0);
+	if (!err) {
+		iput(inode);
+		if (hlinked && idx >= 0)
+			au_xinondir_leave(sb, btop, h_ino, idx);
+		goto new_ino;
+	}
+
+out_iput:
+	iput(inode);
+	inode = ERR_PTR(err);
+out_xinondir:
+	if (hlinked && idx >= 0)
+		au_xinondir_leave(sb, btop, h_ino, idx);
+out:
+	return inode;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_test_ro(struct super_block *sb, aufs_bindex_t bindex,
+	       struct inode *inode)
+{
+	int err;
+	struct inode *hi;
+
+	err = au_br_rdonly(au_sbr(sb, bindex));
+
+	/* pseudo-link after flushed may happen out of bounds */
+	if (!err
+	    && inode
+	    && au_ibtop(inode) <= bindex
+	    && bindex <= au_ibbot(inode)) {
+		/*
+		 * permission check is unnecessary since vfsub routine
+		 * will be called later
+		 */
+		hi = au_h_iptr(inode, bindex);
+		if (hi)
+			err = IS_IMMUTABLE(hi) ? -EROFS : 0;
+	}
+
+	return err;
+}
+
+int au_test_h_perm(struct user_namespace *h_userns, struct inode *h_inode,
+		   int mask)
+{
+	if (uid_eq(current_fsuid(), GLOBAL_ROOT_UID))
+		return 0;
+	return inode_permission(h_userns, h_inode, mask);
+}
+
+int au_test_h_perm_sio(struct user_namespace *h_userns, struct inode *h_inode,
+		       int mask)
+{
+	if (au_test_nfs(h_inode->i_sb)
+	    && (mask & MAY_WRITE)
+	    && S_ISDIR(h_inode->i_mode))
+		mask |= MAY_READ; /* force permission check */
+	return au_test_h_perm(h_userns, h_inode, mask);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/inode.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/inode.h
@@ -0,0 +1,705 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * inode operations
+ */
+
+#ifndef __AUFS_INODE_H__
+#define __AUFS_INODE_H__
+
+#ifdef __KERNEL__
+
+#include <linux/fsnotify.h>
+#include "rwsem.h"
+
+struct vfsmount;
+
+struct au_hnotify {
+#ifdef CONFIG_AUFS_HNOTIFY
+#ifdef CONFIG_AUFS_HFSNOTIFY
+	/* never use fsnotify_add_vfsmount_mark() */
+	struct fsnotify_mark		hn_mark;
+#endif
+	struct inode		*hn_aufs_inode;	/* no get/put */
+	struct rcu_head		rcu;
+#endif
+} ____cacheline_aligned_in_smp;
+
+struct au_hinode {
+	struct inode		*hi_inode;
+	aufs_bindex_t		hi_id;
+#ifdef CONFIG_AUFS_HNOTIFY
+	struct au_hnotify	*hi_notify;
+#endif
+
+	/* reference to the copied-up whiteout with get/put */
+	struct dentry		*hi_whdentry;
+};
+
+/* ig_flags */
+#define AuIG_HALF_REFRESHED		1
+#define au_ig_ftest(flags, name)	((flags) & AuIG_##name)
+#define au_ig_fset(flags, name) \
+	do { (flags) |= AuIG_##name; } while (0)
+#define au_ig_fclr(flags, name) \
+	do { (flags) &= ~AuIG_##name; } while (0)
+
+struct au_iigen {
+	spinlock_t	ig_spin;
+	__u32		ig_generation, ig_flags;
+};
+
+struct au_vdir;
+struct au_iinfo {
+	struct au_iigen		ii_generation;
+	struct super_block	*ii_hsb1;	/* no get/put */
+
+	struct au_rwsem		ii_rwsem;
+	aufs_bindex_t		ii_btop, ii_bbot;
+	__u32			ii_higen;
+	struct au_hinode	*ii_hinode;
+	struct au_vdir		*ii_vdir;
+};
+
+struct au_icntnr {
+	struct au_iinfo		iinfo;
+	struct inode		vfs_inode;
+	struct hlist_bl_node	plink;
+	struct rcu_head		rcu;
+} ____cacheline_aligned_in_smp;
+
+/* au_pin flags */
+#define AuPin_DI_LOCKED		1
+#define AuPin_MNT_WRITE		(1 << 1)
+#define au_ftest_pin(flags, name)	((flags) & AuPin_##name)
+#define au_fset_pin(flags, name) \
+	do { (flags) |= AuPin_##name; } while (0)
+#define au_fclr_pin(flags, name) \
+	do { (flags) &= ~AuPin_##name; } while (0)
+
+struct au_pin {
+	/* input */
+	struct dentry *dentry;
+	unsigned int udba;
+	unsigned char lsc_di, lsc_hi, flags;
+	aufs_bindex_t bindex;
+
+	/* output */
+	struct dentry *parent;
+	struct au_hinode *hdir;
+	struct vfsmount *h_mnt;
+
+	/* temporary unlock/relock for copyup */
+	struct dentry *h_dentry, *h_parent;
+	struct au_branch *br;
+	struct task_struct *task;
+};
+
+void au_pin_hdir_unlock(struct au_pin *p);
+int au_pin_hdir_lock(struct au_pin *p);
+int au_pin_hdir_relock(struct au_pin *p);
+void au_pin_hdir_acquire_nest(struct au_pin *p);
+void au_pin_hdir_release(struct au_pin *p);
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct au_iinfo *au_ii(struct inode *inode)
+{
+	BUG_ON(is_bad_inode(inode));
+	return &(container_of(inode, struct au_icntnr, vfs_inode)->iinfo);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* inode.c */
+struct inode *au_igrab(struct inode *inode);
+void au_refresh_iop(struct inode *inode, int force_getattr);
+int au_refresh_hinode_self(struct inode *inode);
+int au_refresh_hinode(struct inode *inode, struct dentry *dentry);
+int au_ino(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+	   unsigned int d_type, ino_t *ino);
+struct inode *au_new_inode(struct dentry *dentry, int must_new);
+int au_test_ro(struct super_block *sb, aufs_bindex_t bindex,
+	       struct inode *inode);
+int au_test_h_perm(struct user_namespace *h_userns, struct inode *h_inode,
+		   int mask);
+int au_test_h_perm_sio(struct user_namespace *h_userns, struct inode *h_inode,
+		       int mask);
+
+static inline int au_wh_ino(struct super_block *sb, aufs_bindex_t bindex,
+			    ino_t h_ino, unsigned int d_type, ino_t *ino)
+{
+#ifdef CONFIG_AUFS_SHWH
+	return au_ino(sb, bindex, h_ino, d_type, ino);
+#else
+	return 0;
+#endif
+}
+
+/* i_op.c */
+enum {
+	AuIop_SYMLINK,
+	AuIop_DIR,
+	AuIop_OTHER,
+	AuIop_Last
+};
+extern struct inode_operations aufs_iop[AuIop_Last], /* not const */
+	aufs_iop_nogetattr[AuIop_Last];
+
+/* au_wr_dir flags */
+#define AuWrDir_ADD_ENTRY	1
+#define AuWrDir_ISDIR		(1 << 1)
+#define AuWrDir_TMPFILE		(1 << 2)
+#define au_ftest_wrdir(flags, name)	((flags) & AuWrDir_##name)
+#define au_fset_wrdir(flags, name) \
+	do { (flags) |= AuWrDir_##name; } while (0)
+#define au_fclr_wrdir(flags, name) \
+	do { (flags) &= ~AuWrDir_##name; } while (0)
+
+struct au_wr_dir_args {
+	aufs_bindex_t force_btgt;
+	unsigned char flags;
+};
+int au_wr_dir(struct dentry *dentry, struct dentry *src_dentry,
+	      struct au_wr_dir_args *args);
+
+struct dentry *au_pinned_h_parent(struct au_pin *pin);
+void au_pin_init(struct au_pin *pin, struct dentry *dentry,
+		 aufs_bindex_t bindex, int lsc_di, int lsc_hi,
+		 unsigned int udba, unsigned char flags);
+int au_pin(struct au_pin *pin, struct dentry *dentry, aufs_bindex_t bindex,
+	   unsigned int udba, unsigned char flags) __must_check;
+int au_do_pin(struct au_pin *pin) __must_check;
+void au_unpin(struct au_pin *pin);
+int au_reval_for_attr(struct dentry *dentry, unsigned int sigen);
+
+#define AuIcpup_DID_CPUP	1
+#define au_ftest_icpup(flags, name)	((flags) & AuIcpup_##name)
+#define au_fset_icpup(flags, name) \
+	do { (flags) |= AuIcpup_##name; } while (0)
+#define au_fclr_icpup(flags, name) \
+	do { (flags) &= ~AuIcpup_##name; } while (0)
+
+struct au_icpup_args {
+	unsigned char flags;
+	unsigned char pin_flags;
+	aufs_bindex_t btgt;
+	unsigned int udba;
+	struct au_pin pin;
+	struct path h_path;
+	struct inode *h_inode;
+};
+
+int au_pin_and_icpup(struct dentry *dentry, struct iattr *ia,
+		     struct au_icpup_args *a);
+
+int au_h_path_getattr(struct dentry *dentry, struct inode *inode, int force,
+		      struct path *h_path, int locked);
+
+/* i_op_add.c */
+int au_may_add(struct dentry *dentry, aufs_bindex_t bindex,
+	       struct dentry *h_parent, int isdir);
+int aufs_mknod(struct user_namespace *userns, struct inode *dir,
+	       struct dentry *dentry, umode_t mode, dev_t dev);
+int aufs_symlink(struct user_namespace *userns, struct inode *dir,
+		 struct dentry *dentry, const char *symname);
+int aufs_create(struct user_namespace *userns, struct inode *dir,
+		struct dentry *dentry, umode_t mode, bool want_excl);
+struct vfsub_aopen_args;
+int au_aopen_or_create(struct inode *dir, struct dentry *dentry,
+		       struct vfsub_aopen_args *args);
+int aufs_tmpfile(struct user_namespace *userns, struct inode *dir,
+		 struct dentry *dentry, umode_t mode);
+int aufs_link(struct dentry *src_dentry, struct inode *dir,
+	      struct dentry *dentry);
+int aufs_mkdir(struct user_namespace *userns, struct inode *dir,
+	       struct dentry *dentry, umode_t mode);
+
+/* i_op_del.c */
+int au_wr_dir_need_wh(struct dentry *dentry, int isdir, aufs_bindex_t *bcpup);
+int au_may_del(struct dentry *dentry, aufs_bindex_t bindex,
+	       struct dentry *h_parent, int isdir);
+int aufs_unlink(struct inode *dir, struct dentry *dentry);
+int aufs_rmdir(struct inode *dir, struct dentry *dentry);
+
+/* i_op_ren.c */
+int au_wbr(struct dentry *dentry, aufs_bindex_t btgt);
+int aufs_rename(struct user_namespace *userns,
+		struct inode *_src_dir, struct dentry *_src_dentry,
+		struct inode *_dst_dir, struct dentry *_dst_dentry,
+		unsigned int _flags);
+
+/* iinfo.c */
+struct inode *au_h_iptr(struct inode *inode, aufs_bindex_t bindex);
+void au_hiput(struct au_hinode *hinode);
+void au_set_hi_wh(struct inode *inode, aufs_bindex_t bindex,
+		  struct dentry *h_wh);
+unsigned int au_hi_flags(struct inode *inode, int isdir);
+
+/* hinode flags */
+#define AuHi_XINO	1
+#define AuHi_HNOTIFY	(1 << 1)
+#define au_ftest_hi(flags, name)	((flags) & AuHi_##name)
+#define au_fset_hi(flags, name) \
+	do { (flags) |= AuHi_##name; } while (0)
+#define au_fclr_hi(flags, name) \
+	do { (flags) &= ~AuHi_##name; } while (0)
+
+#ifndef CONFIG_AUFS_HNOTIFY
+#undef AuHi_HNOTIFY
+#define AuHi_HNOTIFY	0
+#endif
+
+void au_set_h_iptr(struct inode *inode, aufs_bindex_t bindex,
+		   struct inode *h_inode, unsigned int flags);
+
+void au_update_iigen(struct inode *inode, int half);
+void au_update_ibrange(struct inode *inode, int do_put_zero);
+
+void au_icntnr_init_once(void *_c);
+void au_hinode_init(struct au_hinode *hinode);
+int au_iinfo_init(struct inode *inode);
+void au_iinfo_fin(struct inode *inode);
+int au_hinode_realloc(struct au_iinfo *iinfo, int nbr, int may_shrink);
+
+#ifdef CONFIG_PROC_FS
+/* plink.c */
+int au_plink_maint(struct super_block *sb, int flags);
+struct au_sbinfo;
+void au_plink_maint_leave(struct au_sbinfo *sbinfo);
+int au_plink_maint_enter(struct super_block *sb);
+#ifdef CONFIG_AUFS_DEBUG
+void au_plink_list(struct super_block *sb);
+#else
+AuStubVoid(au_plink_list, struct super_block *sb)
+#endif
+int au_plink_test(struct inode *inode);
+struct dentry *au_plink_lkup(struct inode *inode, aufs_bindex_t bindex);
+void au_plink_append(struct inode *inode, aufs_bindex_t bindex,
+		     struct dentry *h_dentry);
+void au_plink_put(struct super_block *sb, int verbose);
+void au_plink_clean(struct super_block *sb, int verbose);
+void au_plink_half_refresh(struct super_block *sb, aufs_bindex_t br_id);
+#else
+AuStubInt0(au_plink_maint, struct super_block *sb, int flags);
+AuStubVoid(au_plink_maint_leave, struct au_sbinfo *sbinfo);
+AuStubInt0(au_plink_maint_enter, struct super_block *sb);
+AuStubVoid(au_plink_list, struct super_block *sb);
+AuStubInt0(au_plink_test, struct inode *inode);
+AuStub(struct dentry *, au_plink_lkup, return NULL,
+       struct inode *inode, aufs_bindex_t bindex);
+AuStubVoid(au_plink_append, struct inode *inode, aufs_bindex_t bindex,
+	   struct dentry *h_dentry);
+AuStubVoid(au_plink_put, struct super_block *sb, int verbose);
+AuStubVoid(au_plink_clean, struct super_block *sb, int verbose);
+AuStubVoid(au_plink_half_refresh, struct super_block *sb, aufs_bindex_t br_id);
+#endif /* CONFIG_PROC_FS */
+
+#ifdef CONFIG_AUFS_XATTR
+/* xattr.c */
+int au_cpup_xattr(struct path *h_dst, struct path *h_src, int ignore_flags,
+		  unsigned int verbose);
+ssize_t aufs_listxattr(struct dentry *dentry, char *list, size_t size);
+void au_xattr_init(struct super_block *sb);
+#else
+AuStubInt0(au_cpup_xattr, struct path *h_dst, struct path *h_src,
+	   int ignore_flags, unsigned int verbose);
+AuStubVoid(au_xattr_init, struct super_block *sb);
+#endif
+
+#ifdef CONFIG_FS_POSIX_ACL
+struct posix_acl *aufs_get_acl(struct inode *inode, int type, bool rcu);
+int aufs_set_acl(struct user_namespace *userns, struct inode *inode,
+		 struct posix_acl *acl, int type);
+#endif
+
+#if IS_ENABLED(CONFIG_AUFS_XATTR) || IS_ENABLED(CONFIG_FS_POSIX_ACL)
+enum {
+	AU_XATTR_SET,
+	AU_ACL_SET
+};
+
+struct au_sxattr {
+	int type;
+	union {
+		struct {
+			const char	*name;
+			const void	*value;
+			size_t		size;
+			int		flags;
+		} set;
+		struct {
+			struct posix_acl *acl;
+			int		type;
+		} acl_set;
+	} u;
+};
+ssize_t au_sxattr(struct dentry *dentry, struct inode *inode,
+		  struct au_sxattr *arg);
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+/* lock subclass for iinfo */
+enum {
+	AuLsc_II_CHILD,		/* child first */
+	AuLsc_II_CHILD2,	/* rename(2), link(2), and cpup at hnotify */
+	AuLsc_II_CHILD3,	/* copyup dirs */
+	AuLsc_II_PARENT,	/* see AuLsc_I_PARENT in vfsub.h */
+	AuLsc_II_PARENT2,
+	AuLsc_II_PARENT3,	/* copyup dirs */
+	AuLsc_II_NEW_CHILD
+};
+
+/*
+ * ii_read_lock_child, ii_write_lock_child,
+ * ii_read_lock_child2, ii_write_lock_child2,
+ * ii_read_lock_child3, ii_write_lock_child3,
+ * ii_read_lock_parent, ii_write_lock_parent,
+ * ii_read_lock_parent2, ii_write_lock_parent2,
+ * ii_read_lock_parent3, ii_write_lock_parent3,
+ * ii_read_lock_new_child, ii_write_lock_new_child,
+ */
+#define AuReadLockFunc(name, lsc) \
+static inline void ii_read_lock_##name(struct inode *i) \
+{ \
+	au_rw_read_lock_nested(&au_ii(i)->ii_rwsem, AuLsc_II_##lsc); \
+}
+
+#define AuWriteLockFunc(name, lsc) \
+static inline void ii_write_lock_##name(struct inode *i) \
+{ \
+	au_rw_write_lock_nested(&au_ii(i)->ii_rwsem, AuLsc_II_##lsc); \
+}
+
+#define AuRWLockFuncs(name, lsc) \
+	AuReadLockFunc(name, lsc) \
+	AuWriteLockFunc(name, lsc)
+
+AuRWLockFuncs(child, CHILD);
+AuRWLockFuncs(child2, CHILD2);
+AuRWLockFuncs(child3, CHILD3);
+AuRWLockFuncs(parent, PARENT);
+AuRWLockFuncs(parent2, PARENT2);
+AuRWLockFuncs(parent3, PARENT3);
+AuRWLockFuncs(new_child, NEW_CHILD);
+
+#undef AuReadLockFunc
+#undef AuWriteLockFunc
+#undef AuRWLockFuncs
+
+#define ii_read_unlock(i)	au_rw_read_unlock(&au_ii(i)->ii_rwsem)
+#define ii_write_unlock(i)	au_rw_write_unlock(&au_ii(i)->ii_rwsem)
+#define ii_downgrade_lock(i)	au_rw_dgrade_lock(&au_ii(i)->ii_rwsem)
+
+#define IiMustNoWaiters(i)	AuRwMustNoWaiters(&au_ii(i)->ii_rwsem)
+#define IiMustAnyLock(i)	AuRwMustAnyLock(&au_ii(i)->ii_rwsem)
+#define IiMustWriteLock(i)	AuRwMustWriteLock(&au_ii(i)->ii_rwsem)
+
+/* ---------------------------------------------------------------------- */
+
+static inline void au_icntnr_init(struct au_icntnr *c)
+{
+#ifdef CONFIG_AUFS_DEBUG
+	c->vfs_inode.i_mode = 0;
+#endif
+}
+
+static inline unsigned int au_iigen(struct inode *inode, unsigned int *igflags)
+{
+	unsigned int gen;
+	struct au_iinfo *iinfo;
+	struct au_iigen *iigen;
+
+	iinfo = au_ii(inode);
+	iigen = &iinfo->ii_generation;
+	spin_lock(&iigen->ig_spin);
+	if (igflags)
+		*igflags = iigen->ig_flags;
+	gen = iigen->ig_generation;
+	spin_unlock(&iigen->ig_spin);
+
+	return gen;
+}
+
+/* tiny test for inode number */
+/* tmpfs generation is too rough */
+static inline int au_test_higen(struct inode *inode, struct inode *h_inode)
+{
+	struct au_iinfo *iinfo;
+
+	iinfo = au_ii(inode);
+	AuRwMustAnyLock(&iinfo->ii_rwsem);
+	return !(iinfo->ii_hsb1 == h_inode->i_sb
+		 && iinfo->ii_higen == h_inode->i_generation);
+}
+
+static inline void au_iigen_dec(struct inode *inode)
+{
+	struct au_iinfo *iinfo;
+	struct au_iigen *iigen;
+
+	iinfo = au_ii(inode);
+	iigen = &iinfo->ii_generation;
+	spin_lock(&iigen->ig_spin);
+	iigen->ig_generation--;
+	spin_unlock(&iigen->ig_spin);
+}
+
+static inline int au_iigen_test(struct inode *inode, unsigned int sigen)
+{
+	int err;
+
+	err = 0;
+	if (unlikely(inode && au_iigen(inode, NULL) != sigen))
+		err = -EIO;
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct au_hinode *au_hinode(struct au_iinfo *iinfo,
+					  aufs_bindex_t bindex)
+{
+	return iinfo->ii_hinode + bindex;
+}
+
+static inline int au_is_bad_inode(struct inode *inode)
+{
+	return !!(is_bad_inode(inode) || !au_hinode(au_ii(inode), 0));
+}
+
+static inline aufs_bindex_t au_ii_br_id(struct inode *inode,
+					aufs_bindex_t bindex)
+{
+	IiMustAnyLock(inode);
+	return au_hinode(au_ii(inode), bindex)->hi_id;
+}
+
+static inline aufs_bindex_t au_ibtop(struct inode *inode)
+{
+	IiMustAnyLock(inode);
+	return au_ii(inode)->ii_btop;
+}
+
+static inline aufs_bindex_t au_ibbot(struct inode *inode)
+{
+	IiMustAnyLock(inode);
+	return au_ii(inode)->ii_bbot;
+}
+
+static inline struct au_vdir *au_ivdir(struct inode *inode)
+{
+	IiMustAnyLock(inode);
+	return au_ii(inode)->ii_vdir;
+}
+
+static inline struct dentry *au_hi_wh(struct inode *inode, aufs_bindex_t bindex)
+{
+	IiMustAnyLock(inode);
+	return au_hinode(au_ii(inode), bindex)->hi_whdentry;
+}
+
+static inline void au_set_ibtop(struct inode *inode, aufs_bindex_t bindex)
+{
+	IiMustWriteLock(inode);
+	au_ii(inode)->ii_btop = bindex;
+}
+
+static inline void au_set_ibbot(struct inode *inode, aufs_bindex_t bindex)
+{
+	IiMustWriteLock(inode);
+	au_ii(inode)->ii_bbot = bindex;
+}
+
+static inline void au_set_ivdir(struct inode *inode, struct au_vdir *vdir)
+{
+	IiMustWriteLock(inode);
+	au_ii(inode)->ii_vdir = vdir;
+}
+
+static inline struct au_hinode *au_hi(struct inode *inode, aufs_bindex_t bindex)
+{
+	IiMustAnyLock(inode);
+	return au_hinode(au_ii(inode), bindex);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct dentry *au_pinned_parent(struct au_pin *pin)
+{
+	if (pin)
+		return pin->parent;
+	return NULL;
+}
+
+static inline struct inode *au_pinned_h_dir(struct au_pin *pin)
+{
+	if (pin && pin->hdir)
+		return pin->hdir->hi_inode;
+	return NULL;
+}
+
+static inline struct au_hinode *au_pinned_hdir(struct au_pin *pin)
+{
+	if (pin)
+		return pin->hdir;
+	return NULL;
+}
+
+static inline void au_pin_set_dentry(struct au_pin *pin, struct dentry *dentry)
+{
+	if (pin)
+		pin->dentry = dentry;
+}
+
+static inline void au_pin_set_parent_lflag(struct au_pin *pin,
+					   unsigned char lflag)
+{
+	if (pin) {
+		if (lflag)
+			au_fset_pin(pin->flags, DI_LOCKED);
+		else
+			au_fclr_pin(pin->flags, DI_LOCKED);
+	}
+}
+
+#if 0 /* reserved */
+static inline void au_pin_set_parent(struct au_pin *pin, struct dentry *parent)
+{
+	if (pin) {
+		dput(pin->parent);
+		pin->parent = dget(parent);
+	}
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+struct au_branch;
+#ifdef CONFIG_AUFS_HNOTIFY
+struct au_hnotify_op {
+	void (*ctl)(struct au_hinode *hinode, int do_set);
+	int (*alloc)(struct au_hinode *hinode);
+
+	/*
+	 * if it returns true, the caller should free hinode->hi_notify,
+	 * otherwise ->free() frees it.
+	 */
+	int (*free)(struct au_hinode *hinode,
+		    struct au_hnotify *hn) __must_check;
+
+	void (*fin)(void);
+	int (*init)(void);
+
+	int (*reset_br)(unsigned int udba, struct au_branch *br, int perm);
+	void (*fin_br)(struct au_branch *br);
+	int (*init_br)(struct au_branch *br, int perm);
+};
+
+/* hnotify.c */
+int au_hn_alloc(struct au_hinode *hinode, struct inode *inode);
+void au_hn_free(struct au_hinode *hinode);
+void au_hn_ctl(struct au_hinode *hinode, int do_set);
+void au_hn_reset(struct inode *inode, unsigned int flags);
+int au_hnotify(struct inode *h_dir, struct au_hnotify *hnotify, u32 mask,
+	       const struct qstr *h_child_qstr, struct inode *h_child_inode);
+int au_hnotify_reset_br(unsigned int udba, struct au_branch *br, int perm);
+int au_hnotify_init_br(struct au_branch *br, int perm);
+void au_hnotify_fin_br(struct au_branch *br);
+int __init au_hnotify_init(void);
+void au_hnotify_fin(void);
+
+/* hfsnotify.c */
+extern const struct au_hnotify_op au_hnotify_op;
+
+static inline
+void au_hn_init(struct au_hinode *hinode)
+{
+	hinode->hi_notify = NULL;
+}
+
+static inline struct au_hnotify *au_hn(struct au_hinode *hinode)
+{
+	return hinode->hi_notify;
+}
+
+#else
+AuStub(int, au_hn_alloc, return -EOPNOTSUPP,
+       struct au_hinode *hinode __maybe_unused,
+       struct inode *inode __maybe_unused)
+AuStub(struct au_hnotify *, au_hn, return NULL, struct au_hinode *hinode)
+AuStubVoid(au_hn_free, struct au_hinode *hinode __maybe_unused)
+AuStubVoid(au_hn_ctl, struct au_hinode *hinode __maybe_unused,
+	   int do_set __maybe_unused)
+AuStubVoid(au_hn_reset, struct inode *inode __maybe_unused,
+	   unsigned int flags __maybe_unused)
+AuStubInt0(au_hnotify_reset_br, unsigned int udba __maybe_unused,
+	   struct au_branch *br __maybe_unused,
+	   int perm __maybe_unused)
+AuStubInt0(au_hnotify_init_br, struct au_branch *br __maybe_unused,
+	   int perm __maybe_unused)
+AuStubVoid(au_hnotify_fin_br, struct au_branch *br __maybe_unused)
+AuStubInt0(__init au_hnotify_init, void)
+AuStubVoid(au_hnotify_fin, void)
+AuStubVoid(au_hn_init, struct au_hinode *hinode __maybe_unused)
+#endif /* CONFIG_AUFS_HNOTIFY */
+
+static inline void au_hn_suspend(struct au_hinode *hdir)
+{
+	au_hn_ctl(hdir, /*do_set*/0);
+}
+
+static inline void au_hn_resume(struct au_hinode *hdir)
+{
+	au_hn_ctl(hdir, /*do_set*/1);
+}
+
+static inline void au_hn_inode_lock(struct au_hinode *hdir)
+{
+	inode_lock(hdir->hi_inode);
+	au_hn_suspend(hdir);
+}
+
+static inline void au_hn_inode_lock_nested(struct au_hinode *hdir,
+					  unsigned int sc __maybe_unused)
+{
+	inode_lock_nested(hdir->hi_inode, sc);
+	au_hn_suspend(hdir);
+}
+
+#if 0 /* unused */
+#include "vfsub.h"
+static inline void au_hn_inode_lock_shared_nested(struct au_hinode *hdir,
+						  unsigned int sc)
+{
+	inode_lock_shared_nested(hdir->hi_inode, sc);
+	au_hn_suspend(hdir);
+}
+#endif
+
+static inline void au_hn_inode_unlock(struct au_hinode *hdir)
+{
+	au_hn_resume(hdir);
+	inode_unlock(hdir->hi_inode);
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_INODE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/ioctl.c
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * ioctl
+ * plink-management and readdir in userspace.
+ * assist the pathconf(3) wrapper library.
+ * move-down
+ * File-based Hierarchical Storage Management.
+ */
+
+#include <linux/compat.h>
+#include <linux/file.h>
+#include "aufs.h"
+
+static int au_wbr_fd(struct path *path, struct aufs_wbr_fd __user *arg)
+{
+	int err, fd;
+	aufs_bindex_t wbi, bindex, bbot;
+	struct file *h_file;
+	struct super_block *sb;
+	struct dentry *root;
+	struct au_branch *br;
+	struct aufs_wbr_fd wbrfd = {
+		.oflags	= au_dir_roflags,
+		.brid	= -1
+	};
+	const int valid = O_RDONLY | O_NONBLOCK | O_LARGEFILE | O_DIRECTORY
+		| O_NOATIME | O_CLOEXEC;
+
+	AuDebugOn(wbrfd.oflags & ~valid);
+
+	if (arg) {
+		err = copy_from_user(&wbrfd, arg, sizeof(wbrfd));
+		if (unlikely(err)) {
+			err = -EFAULT;
+			goto out;
+		}
+
+		err = -EINVAL;
+		AuDbg("wbrfd{0%o, %d}\n", wbrfd.oflags, wbrfd.brid);
+		wbrfd.oflags |= au_dir_roflags;
+		AuDbg("0%o\n", wbrfd.oflags);
+		if (unlikely(wbrfd.oflags & ~valid))
+			goto out;
+	}
+
+	fd = get_unused_fd_flags(0);
+	err = fd;
+	if (unlikely(fd < 0))
+		goto out;
+
+	h_file = ERR_PTR(-EINVAL);
+	wbi = 0;
+	br = NULL;
+	sb = path->dentry->d_sb;
+	root = sb->s_root;
+	aufs_read_lock(root, AuLock_IR);
+	bbot = au_sbbot(sb);
+	if (wbrfd.brid >= 0) {
+		wbi = au_br_index(sb, wbrfd.brid);
+		if (unlikely(wbi < 0 || wbi > bbot))
+			goto out_unlock;
+	}
+
+	h_file = ERR_PTR(-ENOENT);
+	br = au_sbr(sb, wbi);
+	if (!au_br_writable(br->br_perm)) {
+		if (arg)
+			goto out_unlock;
+
+		bindex = wbi + 1;
+		wbi = -1;
+		for (; bindex <= bbot; bindex++) {
+			br = au_sbr(sb, bindex);
+			if (au_br_writable(br->br_perm)) {
+				wbi = bindex;
+				br = au_sbr(sb, wbi);
+				break;
+			}
+		}
+	}
+	AuDbg("wbi %d\n", wbi);
+	if (wbi >= 0)
+		h_file = au_h_open(root, wbi, wbrfd.oflags, NULL,
+				   /*force_wr*/0);
+
+out_unlock:
+	aufs_read_unlock(root, AuLock_IR);
+	err = PTR_ERR(h_file);
+	if (IS_ERR(h_file))
+		goto out_fd;
+
+	au_lcnt_dec(&br->br_nfiles); /* cf. au_h_open() */
+	fd_install(fd, h_file);
+	err = fd;
+	goto out; /* success */
+
+out_fd:
+	put_unused_fd(fd);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+long aufs_ioctl_dir(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	long err;
+	struct dentry *dentry;
+
+	switch (cmd) {
+	case AUFS_CTL_RDU:
+	case AUFS_CTL_RDU_INO:
+		err = au_rdu_ioctl(file, cmd, arg);
+		break;
+
+	case AUFS_CTL_WBR_FD:
+		err = au_wbr_fd(&file->f_path, (void __user *)arg);
+		break;
+
+	case AUFS_CTL_IBUSY:
+		err = au_ibusy_ioctl(file, arg);
+		break;
+
+	case AUFS_CTL_BRINFO:
+		err = au_brinfo_ioctl(file, arg);
+		break;
+
+	case AUFS_CTL_FHSM_FD:
+		dentry = file->f_path.dentry;
+		if (IS_ROOT(dentry))
+			err = au_fhsm_fd(dentry->d_sb, arg);
+		else
+			err = -ENOTTY;
+		break;
+
+	default:
+		/* do not call the lower */
+		AuDbg("0x%x\n", cmd);
+		err = -ENOTTY;
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+long aufs_ioctl_nondir(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	long err;
+
+	switch (cmd) {
+	case AUFS_CTL_MVDOWN:
+		err = au_mvdown(file->f_path.dentry, (void __user *)arg);
+		break;
+
+	case AUFS_CTL_WBR_FD:
+		err = au_wbr_fd(&file->f_path, (void __user *)arg);
+		break;
+
+	default:
+		/* do not call the lower */
+		AuDbg("0x%x\n", cmd);
+		err = -ENOTTY;
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+#ifdef CONFIG_COMPAT
+long aufs_compat_ioctl_dir(struct file *file, unsigned int cmd,
+			   unsigned long arg)
+{
+	long err;
+
+	switch (cmd) {
+	case AUFS_CTL_RDU:
+	case AUFS_CTL_RDU_INO:
+		err = au_rdu_compat_ioctl(file, cmd, arg);
+		break;
+
+	case AUFS_CTL_IBUSY:
+		err = au_ibusy_compat_ioctl(file, arg);
+		break;
+
+	case AUFS_CTL_BRINFO:
+		err = au_brinfo_compat_ioctl(file, arg);
+		break;
+
+	default:
+		err = aufs_ioctl_dir(file, cmd, arg);
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+long aufs_compat_ioctl_nondir(struct file *file, unsigned int cmd,
+			      unsigned long arg)
+{
+	return aufs_ioctl_nondir(file, cmd, (unsigned long)compat_ptr(arg));
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/lcnt.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/lcnt.h
@@ -0,0 +1,186 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * simple long counter wrapper
+ */
+
+#ifndef __AUFS_LCNT_H__
+#define __AUFS_LCNT_H__
+
+#ifdef __KERNEL__
+
+#include "debug.h"
+
+#define AuLCntATOMIC	1
+#define AuLCntPCPUCNT	2
+/*
+ * why does percpu_refcount require extra synchronize_rcu()s in
+ * au_br_do_free()
+ */
+#define AuLCntPCPUREF	3
+
+/* #define AuLCntChosen	AuLCntATOMIC */
+#define AuLCntChosen	AuLCntPCPUCNT
+/* #define AuLCntChosen	AuLCntPCPUREF */
+
+#if AuLCntChosen == AuLCntATOMIC
+#include <linux/atomic.h>
+
+typedef atomic_long_t au_lcnt_t;
+
+static inline int au_lcnt_init(au_lcnt_t *cnt, void *release __maybe_unused)
+{
+	atomic_long_set(cnt, 0);
+	return 0;
+}
+
+static inline void au_lcnt_wait_for_fin(au_lcnt_t *cnt __maybe_unused)
+{
+	/* empty */
+}
+
+static inline void au_lcnt_fin(au_lcnt_t *cnt __maybe_unused,
+			       int do_sync __maybe_unused)
+{
+	/* empty */
+}
+
+static inline void au_lcnt_inc(au_lcnt_t *cnt)
+{
+	atomic_long_inc(cnt);
+}
+
+static inline void au_lcnt_dec(au_lcnt_t *cnt)
+{
+	atomic_long_dec(cnt);
+}
+
+static inline long au_lcnt_read(au_lcnt_t *cnt, int do_rev __maybe_unused)
+{
+	return atomic_long_read(cnt);
+}
+#endif
+
+#if AuLCntChosen == AuLCntPCPUCNT
+#include <linux/percpu_counter.h>
+
+typedef struct percpu_counter au_lcnt_t;
+
+static inline int au_lcnt_init(au_lcnt_t *cnt, void *release __maybe_unused)
+{
+	return percpu_counter_init(cnt, 0, GFP_NOFS);
+}
+
+static inline void au_lcnt_wait_for_fin(au_lcnt_t *cnt __maybe_unused)
+{
+	/* empty */
+}
+
+static inline void au_lcnt_fin(au_lcnt_t *cnt, int do_sync __maybe_unused)
+{
+	percpu_counter_destroy(cnt);
+}
+
+static inline void au_lcnt_inc(au_lcnt_t *cnt)
+{
+	percpu_counter_inc(cnt);
+}
+
+static inline void au_lcnt_dec(au_lcnt_t *cnt)
+{
+	percpu_counter_dec(cnt);
+}
+
+static inline long au_lcnt_read(au_lcnt_t *cnt, int do_rev __maybe_unused)
+{
+	s64 n;
+
+	n = percpu_counter_sum(cnt);
+	BUG_ON(n < 0);
+	if (LONG_MAX != LLONG_MAX
+	    && n > LONG_MAX)
+		AuWarn1("%s\n", "wrap-around");
+
+	return n;
+}
+#endif
+
+#if AuLCntChosen == AuLCntPCPUREF
+#include <linux/percpu-refcount.h>
+
+typedef struct percpu_ref au_lcnt_t;
+
+static inline int au_lcnt_init(au_lcnt_t *cnt, percpu_ref_func_t *release)
+{
+	if (!release)
+		release = percpu_ref_exit;
+	return percpu_ref_init(cnt, release, /*percpu mode*/0, GFP_NOFS);
+}
+
+static inline void au_lcnt_wait_for_fin(au_lcnt_t *cnt __maybe_unused)
+{
+	synchronize_rcu();
+}
+
+static inline void au_lcnt_fin(au_lcnt_t *cnt, int do_sync)
+{
+	percpu_ref_kill(cnt);
+	if (do_sync)
+		au_lcnt_wait_for_fin(cnt);
+}
+
+static inline void au_lcnt_inc(au_lcnt_t *cnt)
+{
+	percpu_ref_get(cnt);
+}
+
+static inline void au_lcnt_dec(au_lcnt_t *cnt)
+{
+	percpu_ref_put(cnt);
+}
+
+/*
+ * avoid calling this func as possible.
+ */
+static inline long au_lcnt_read(au_lcnt_t *cnt, int do_rev)
+{
+	long l;
+
+	percpu_ref_switch_to_atomic_sync(cnt);
+	l = atomic_long_read(&cnt->count);
+	if (do_rev)
+		percpu_ref_switch_to_percpu(cnt);
+
+	/* percpu_ref is initialized by 1 instead of 0 */
+	return l - 1;
+}
+#endif
+
+#ifdef CONFIG_AUFS_DEBUG
+#define AuLCntZero(val) do {			\
+	long l = val;				\
+	if (l)					\
+		AuDbg("%s = %ld\n", #val, l);	\
+} while (0)
+#else
+#define AuLCntZero(val)		do {} while (0)
+#endif
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_LCNT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/loop.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/loop.c
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * support for loopback block device as a branch
+ */
+
+#include "aufs.h"
+
+/* added into drivers/block/loop.c */
+static struct file *(*backing_file_func)(struct super_block *sb);
+
+/*
+ * test if two lower dentries have overlapping branches.
+ */
+int au_test_loopback_overlap(struct super_block *sb, struct dentry *h_adding)
+{
+	struct super_block *h_sb;
+	struct file *backing_file;
+
+	if (unlikely(!backing_file_func)) {
+		/* don't load "loop" module here */
+		backing_file_func = symbol_get(loop_backing_file);
+		if (unlikely(!backing_file_func))
+			/* "loop" module is not loaded */
+			return 0;
+	}
+
+	h_sb = h_adding->d_sb;
+	backing_file = backing_file_func(h_sb);
+	if (!backing_file)
+		return 0;
+
+	h_adding = backing_file->f_path.dentry;
+	/*
+	 * h_adding can be local NFS.
+	 * in this case aufs cannot detect the loop.
+	 */
+	if (unlikely(h_adding->d_sb == sb))
+		return 1;
+	return !!au_test_subdir(h_adding, sb->s_root);
+}
+
+/* true if a kernel thread named 'loop[0-9].*' accesses a file */
+int au_test_loopback_kthread(void)
+{
+	int ret;
+	struct task_struct *tsk = current;
+	char c, comm[sizeof(tsk->comm)];
+
+	ret = 0;
+	if (tsk->flags & PF_KTHREAD) {
+		get_task_comm(comm, tsk);
+		c = comm[4];
+		ret = ('0' <= c && c <= '9'
+		       && !strncmp(comm, "loop", 4));
+	}
+
+	return ret;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#define au_warn_loopback_step	16
+static int au_warn_loopback_nelem = au_warn_loopback_step;
+static unsigned long *au_warn_loopback_array;
+
+void au_warn_loopback(struct super_block *h_sb)
+{
+	int i, new_nelem;
+	unsigned long *a, magic;
+	static DEFINE_SPINLOCK(spin);
+
+	magic = h_sb->s_magic;
+	spin_lock(&spin);
+	a = au_warn_loopback_array;
+	for (i = 0; i < au_warn_loopback_nelem && *a; i++)
+		if (a[i] == magic) {
+			spin_unlock(&spin);
+			return;
+		}
+
+	/* h_sb is new to us, print it */
+	if (i < au_warn_loopback_nelem) {
+		a[i] = magic;
+		goto pr;
+	}
+
+	/* expand the array */
+	new_nelem = au_warn_loopback_nelem + au_warn_loopback_step;
+	a = au_kzrealloc(au_warn_loopback_array,
+			 au_warn_loopback_nelem * sizeof(unsigned long),
+			 new_nelem * sizeof(unsigned long), GFP_ATOMIC,
+			 /*may_shrink*/0);
+	if (a) {
+		au_warn_loopback_nelem = new_nelem;
+		au_warn_loopback_array = a;
+		a[i] = magic;
+		goto pr;
+	}
+
+	spin_unlock(&spin);
+	AuWarn1("realloc failed, ignored\n");
+	return;
+
+pr:
+	spin_unlock(&spin);
+	pr_warn("you may want to try another patch for loopback file "
+		"on %s(0x%lx) branch\n", au_sbtype(h_sb), magic);
+}
+
+int au_loopback_init(void)
+{
+	int err;
+	struct super_block *sb __maybe_unused;
+
+	BUILD_BUG_ON(sizeof(sb->s_magic) != sizeof(*au_warn_loopback_array));
+
+	err = 0;
+	au_warn_loopback_array = kcalloc(au_warn_loopback_step,
+					 sizeof(unsigned long), GFP_NOFS);
+	if (unlikely(!au_warn_loopback_array))
+		err = -ENOMEM;
+
+	return err;
+}
+
+void au_loopback_fin(void)
+{
+	if (backing_file_func)
+		symbol_put(loop_backing_file);
+	au_kfree_try_rcu(au_warn_loopback_array);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* support the loopback block device insude aufs */
+
+struct file *aufs_real_loop(struct file *file)
+{
+	struct file *f;
+
+	BUG_ON(!au_test_aufs(file->f_path.dentry->d_sb));
+	fi_read_lock(file);
+	f = au_hf_top(file);
+	fi_read_unlock(file);
+	AuDebugOn(!f);
+	return f;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/loop.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/loop.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * support for loopback mount as a branch
+ */
+
+#ifndef __AUFS_LOOP_H__
+#define __AUFS_LOOP_H__
+
+#ifdef __KERNEL__
+
+struct dentry;
+struct super_block;
+
+#ifdef CONFIG_AUFS_BDEV_LOOP
+/* drivers/block/loop.c */
+struct file *loop_backing_file(struct super_block *sb);
+
+/* loop.c */
+int au_test_loopback_overlap(struct super_block *sb, struct dentry *h_adding);
+int au_test_loopback_kthread(void);
+void au_warn_loopback(struct super_block *h_sb);
+
+int au_loopback_init(void);
+void au_loopback_fin(void);
+
+struct file *aufs_real_loop(struct file *file);
+#else
+AuStub(struct file *, loop_backing_file, return NULL, struct super_block *sb)
+
+AuStubInt0(au_test_loopback_overlap, struct super_block *sb,
+	   struct dentry *h_adding)
+AuStubInt0(au_test_loopback_kthread, void)
+AuStubVoid(au_warn_loopback, struct super_block *h_sb)
+
+AuStubInt0(au_loopback_init, void)
+AuStubVoid(au_loopback_fin, void)
+
+AuStub(struct file *, aufs_real_loop, return NULL, struct file *file)
+#endif /* BLK_DEV_LOOP */
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_LOOP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/magic.mk
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/magic.mk
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+
+# defined in ${srctree}/fs/fuse/inode.c
+# tristate
+ifdef CONFIG_FUSE_FS
+ccflags-y += -DFUSE_SUPER_MAGIC=0x65735546
+endif
+
+# defined in ${srctree}/fs/xfs/xfs_sb.h
+# tristate
+ifdef CONFIG_XFS_FS
+ccflags-y += -DXFS_SB_MAGIC=0x58465342
+endif
+
+# defined in ${srctree}/fs/configfs/mount.c
+# tristate
+ifdef CONFIG_CONFIGFS_FS
+ccflags-y += -DCONFIGFS_MAGIC=0x62656570
+endif
+
+# defined in ${srctree}/fs/ubifs/ubifs.h
+# tristate
+ifdef CONFIG_UBIFS_FS
+ccflags-y += -DUBIFS_SUPER_MAGIC=0x24051905
+endif
+
+# defined in ${srctree}/fs/hfsplus/hfsplus_raw.h
+# tristate
+ifdef CONFIG_HFSPLUS_FS
+ccflags-y += -DHFSPLUS_SUPER_MAGIC=0x482b
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/module.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/module.c
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * module global variables and operations
+ */
+
+#include <linux/module.h>
+#include <linux/seq_file.h>
+#include "aufs.h"
+
+/* shrinkable realloc */
+void *au_krealloc(void *p, unsigned int new_sz, gfp_t gfp, int may_shrink)
+{
+	size_t sz;
+	int diff;
+
+	sz = 0;
+	diff = -1;
+	if (p) {
+#if 0 /* unused */
+		if (!new_sz) {
+			au_kfree_rcu(p);
+			p = NULL;
+			goto out;
+		}
+#else
+		AuDebugOn(!new_sz);
+#endif
+		sz = ksize(p);
+		diff = au_kmidx_sub(sz, new_sz);
+	}
+	if (sz && !diff)
+		goto out;
+
+	if (sz < new_sz)
+		/* expand or SLOB */
+		p = krealloc(p, new_sz, gfp);
+	else if (new_sz < sz && may_shrink) {
+		/* shrink */
+		void *q;
+
+		q = kmalloc(new_sz, gfp);
+		if (q) {
+			if (p) {
+				memcpy(q, p, new_sz);
+				au_kfree_try_rcu(p);
+			}
+			p = q;
+		} else
+			p = NULL;
+	}
+
+out:
+	return p;
+}
+
+void *au_kzrealloc(void *p, unsigned int nused, unsigned int new_sz, gfp_t gfp,
+		   int may_shrink)
+{
+	p = au_krealloc(p, new_sz, gfp, may_shrink);
+	if (p && new_sz > nused)
+		memset(p + nused, 0, new_sz - nused);
+	return p;
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * aufs caches
+ */
+struct kmem_cache *au_cache[AuCache_Last];
+
+static void au_cache_fin(void)
+{
+	int i;
+
+	/*
+	 * Make sure all delayed rcu free inodes are flushed before we
+	 * destroy cache.
+	 */
+	rcu_barrier();
+
+	/* excluding AuCache_HNOTIFY */
+	BUILD_BUG_ON(AuCache_HNOTIFY + 1 != AuCache_Last);
+	for (i = 0; i < AuCache_HNOTIFY; i++) {
+		kmem_cache_destroy(au_cache[i]);
+		au_cache[i] = NULL;
+	}
+}
+
+static int __init au_cache_init(void)
+{
+	au_cache[AuCache_DINFO] = AuCacheCtor(au_dinfo, au_di_init_once);
+	if (au_cache[AuCache_DINFO])
+		/* SLAB_DESTROY_BY_RCU */
+		au_cache[AuCache_ICNTNR] = AuCacheCtor(au_icntnr,
+						       au_icntnr_init_once);
+	if (au_cache[AuCache_ICNTNR])
+		au_cache[AuCache_FINFO] = AuCacheCtor(au_finfo,
+						      au_fi_init_once);
+	if (au_cache[AuCache_FINFO])
+		au_cache[AuCache_VDIR] = AuCache(au_vdir);
+	if (au_cache[AuCache_VDIR])
+		au_cache[AuCache_DEHSTR] = AuCache(au_vdir_dehstr);
+	if (au_cache[AuCache_DEHSTR])
+		return 0;
+
+	au_cache_fin();
+	return -ENOMEM;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_dir_roflags;
+
+#ifdef CONFIG_AUFS_SBILIST
+/*
+ * iterate_supers_type() doesn't protect us from
+ * remounting (branch management)
+ */
+struct hlist_bl_head au_sbilist;
+#endif
+
+/*
+ * functions for module interface.
+ */
+MODULE_LICENSE("GPL");
+/* MODULE_LICENSE("GPL v2"); */
+MODULE_AUTHOR("Junjiro R. Okajima <aufs-users@lists.sourceforge.net>");
+MODULE_DESCRIPTION(AUFS_NAME
+	" -- Advanced multi layered unification filesystem");
+MODULE_VERSION(AUFS_VERSION);
+MODULE_ALIAS_FS(AUFS_NAME);
+
+/* this module parameter has no meaning when SYSFS is disabled */
+int sysaufs_brs = 1;
+MODULE_PARM_DESC(brs, "use <sysfs>/fs/aufs/si_*/brN");
+module_param_named(brs, sysaufs_brs, int, 0444);
+
+/* this module parameter has no meaning when USER_NS is disabled */
+bool au_userns;
+MODULE_PARM_DESC(allow_userns, "allow unprivileged to mount under userns");
+module_param_named(allow_userns, au_userns, bool, 0444);
+
+/* ---------------------------------------------------------------------- */
+
+static char au_esc_chars[0x20 + 3]; /* 0x01-0x20, backslash, del, and NULL */
+
+int au_seq_path(struct seq_file *seq, struct path *path)
+{
+	int err;
+
+	err = seq_path(seq, path, au_esc_chars);
+	if (err >= 0)
+		err = 0;
+	else
+		err = -ENOMEM;
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int __init aufs_init(void)
+{
+	int err, i;
+	char *p;
+
+	p = au_esc_chars;
+	for (i = 1; i <= ' '; i++)
+		*p++ = i;
+	*p++ = '\\';
+	*p++ = '\x7f';
+	*p = 0;
+
+	au_dir_roflags = au_file_roflags(O_DIRECTORY | O_LARGEFILE);
+
+	memcpy(aufs_iop_nogetattr, aufs_iop, sizeof(aufs_iop));
+	for (i = 0; i < AuIop_Last; i++)
+		aufs_iop_nogetattr[i].getattr = NULL;
+
+	memset(au_cache, 0, sizeof(au_cache));	/* including hnotify */
+
+	au_sbilist_init();
+	sysaufs_brs_init();
+	au_debug_init();
+	au_dy_init();
+	err = sysaufs_init();
+	if (unlikely(err))
+		goto out;
+	err = dbgaufs_init();
+	if (unlikely(err))
+		goto out_sysaufs;
+	err = au_procfs_init();
+	if (unlikely(err))
+		goto out_dbgaufs;
+	err = au_wkq_init();
+	if (unlikely(err))
+		goto out_procfs;
+	err = au_loopback_init();
+	if (unlikely(err))
+		goto out_wkq;
+	err = au_hnotify_init();
+	if (unlikely(err))
+		goto out_loopback;
+	err = au_sysrq_init();
+	if (unlikely(err))
+		goto out_hin;
+	err = au_cache_init();
+	if (unlikely(err))
+		goto out_sysrq;
+
+	aufs_fs_type.fs_flags |= au_userns ? FS_USERNS_MOUNT : 0;
+	err = register_filesystem(&aufs_fs_type);
+	if (unlikely(err))
+		goto out_cache;
+
+	/* since we define pr_fmt, call printk directly */
+	printk(KERN_INFO AUFS_NAME " " AUFS_VERSION "\n");
+	goto out; /* success */
+
+out_cache:
+	au_cache_fin();
+out_sysrq:
+	au_sysrq_fin();
+out_hin:
+	au_hnotify_fin();
+out_loopback:
+	au_loopback_fin();
+out_wkq:
+	au_wkq_fin();
+out_procfs:
+	au_procfs_fin();
+out_dbgaufs:
+	dbgaufs_fin();
+out_sysaufs:
+	sysaufs_fin();
+	au_dy_fin();
+out:
+	return err;
+}
+
+static void __exit aufs_exit(void)
+{
+	unregister_filesystem(&aufs_fs_type);
+	au_cache_fin();
+	au_sysrq_fin();
+	au_hnotify_fin();
+	au_loopback_fin();
+	au_wkq_fin();
+	au_procfs_fin();
+	dbgaufs_fin();
+	sysaufs_fin();
+	au_dy_fin();
+}
+
+module_init(aufs_init);
+module_exit(aufs_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/module.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/module.h
@@ -0,0 +1,166 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * module initialization and module-global
+ */
+
+#ifndef __AUFS_MODULE_H__
+#define __AUFS_MODULE_H__
+
+#ifdef __KERNEL__
+
+#include <linux/slab.h>
+#include "debug.h"
+#include "dentry.h"
+#include "dir.h"
+#include "file.h"
+#include "inode.h"
+
+struct path;
+struct seq_file;
+
+/* module parameters */
+extern int sysaufs_brs;
+extern bool au_userns;
+
+/* ---------------------------------------------------------------------- */
+
+extern int au_dir_roflags;
+
+void *au_krealloc(void *p, unsigned int new_sz, gfp_t gfp, int may_shrink);
+void *au_kzrealloc(void *p, unsigned int nused, unsigned int new_sz, gfp_t gfp,
+		   int may_shrink);
+
+/*
+ * Comparing the size of the object with sizeof(struct rcu_head)
+ * case 1: object is always larger
+ *	--> au_kfree_rcu() or au_kfree_do_rcu()
+ * case 2: object is always smaller
+ *	--> au_kfree_small()
+ * case 3: object can be any size
+ *	--> au_kfree_try_rcu()
+ */
+
+static inline void au_kfree_do_rcu(const void *p)
+{
+	struct {
+		struct rcu_head rcu;
+	} *a = (void *)p;
+
+	kfree_rcu(a, rcu);
+}
+
+#define au_kfree_rcu(_p) do {						\
+		typeof(_p) p = (_p);					\
+		BUILD_BUG_ON(sizeof(*p) < sizeof(struct rcu_head));	\
+		if (p)							\
+			au_kfree_do_rcu(p);				\
+	} while (0)
+
+#define au_kfree_do_sz_test(sz)	(sz >= sizeof(struct rcu_head))
+#define au_kfree_sz_test(p)	(p && au_kfree_do_sz_test(ksize(p)))
+
+static inline void au_kfree_try_rcu(const void *p)
+{
+	if (!p)
+		return;
+	if (au_kfree_sz_test(p))
+		au_kfree_do_rcu(p);
+	else
+		kfree(p);
+}
+
+static inline void au_kfree_small(const void *p)
+{
+	if (!p)
+		return;
+	AuDebugOn(au_kfree_sz_test(p));
+	kfree(p);
+}
+
+static inline int au_kmidx_sub(size_t sz, size_t new_sz)
+{
+#ifndef CONFIG_SLOB
+	return __kmalloc_index(sz, false) - __kmalloc_index(new_sz, false);
+#else
+	return -1; /* SLOB is untested */
+#endif
+}
+
+int au_seq_path(struct seq_file *seq, struct path *path);
+
+#ifdef CONFIG_PROC_FS
+/* procfs.c */
+int __init au_procfs_init(void);
+void au_procfs_fin(void);
+#else
+AuStubInt0(au_procfs_init, void);
+AuStubVoid(au_procfs_fin, void);
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+/* kmem cache */
+enum {
+	AuCache_DINFO,
+	AuCache_ICNTNR,
+	AuCache_FINFO,
+	AuCache_VDIR,
+	AuCache_DEHSTR,
+	AuCache_HNOTIFY, /* must be last */
+	AuCache_Last
+};
+
+extern struct kmem_cache *au_cache[AuCache_Last];
+
+#define AuCacheFlags		(SLAB_RECLAIM_ACCOUNT | SLAB_MEM_SPREAD)
+#define AuCache(type)		KMEM_CACHE(type, AuCacheFlags)
+#define AuCacheCtor(type, ctor)	\
+	kmem_cache_create(#type, sizeof(struct type), \
+			  __alignof__(struct type), AuCacheFlags, ctor)
+
+#define AuCacheFuncs(name, index)					\
+	static inline struct au_##name *au_cache_alloc_##name(void)	\
+	{ return kmem_cache_alloc(au_cache[AuCache_##index], GFP_NOFS); } \
+	static inline void au_cache_free_##name##_norcu(struct au_##name *p) \
+	{ kmem_cache_free(au_cache[AuCache_##index], p); }		\
+									\
+	static inline void au_cache_free_##name##_rcu_cb(struct rcu_head *rcu) \
+	{ void *p = rcu;						\
+		p -= offsetof(struct au_##name, rcu);			\
+		kmem_cache_free(au_cache[AuCache_##index], p); }	\
+	static inline void au_cache_free_##name##_rcu(struct au_##name *p) \
+	{ BUILD_BUG_ON(sizeof(struct au_##name) < sizeof(struct rcu_head)); \
+		call_rcu(&p->rcu, au_cache_free_##name##_rcu_cb); }	\
+									\
+	static inline void au_cache_free_##name(struct au_##name *p)	\
+	{ /* au_cache_free_##name##_norcu(p); */			\
+		au_cache_free_##name##_rcu(p); }
+
+AuCacheFuncs(dinfo, DINFO);
+AuCacheFuncs(icntnr, ICNTNR);
+AuCacheFuncs(finfo, FINFO);
+AuCacheFuncs(vdir, VDIR);
+AuCacheFuncs(vdir_dehstr, DEHSTR);
+#ifdef CONFIG_AUFS_HNOTIFY
+AuCacheFuncs(hnotify, HNOTIFY);
+#endif
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_MODULE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/mvdown.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/mvdown.c
@@ -0,0 +1,706 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2011-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * move-down, opposite of copy-up
+ */
+
+#include "aufs.h"
+
+struct au_mvd_args {
+	struct {
+		struct super_block *h_sb;
+		struct dentry *h_parent;
+		struct au_hinode *hdir;
+		struct inode *h_dir, *h_inode;
+		struct au_pin pin;
+	} info[AUFS_MVDOWN_NARRAY];
+
+	struct aufs_mvdown mvdown;
+	struct dentry *dentry, *parent;
+	struct inode *inode, *dir;
+	struct super_block *sb;
+	aufs_bindex_t bopq, bwh, bfound;
+	unsigned char rename_lock;
+};
+
+#define mvd_errno		mvdown.au_errno
+#define mvd_bsrc		mvdown.stbr[AUFS_MVDOWN_UPPER].bindex
+#define mvd_src_brid		mvdown.stbr[AUFS_MVDOWN_UPPER].brid
+#define mvd_bdst		mvdown.stbr[AUFS_MVDOWN_LOWER].bindex
+#define mvd_dst_brid		mvdown.stbr[AUFS_MVDOWN_LOWER].brid
+
+#define mvd_h_src_sb		info[AUFS_MVDOWN_UPPER].h_sb
+#define mvd_h_src_parent	info[AUFS_MVDOWN_UPPER].h_parent
+#define mvd_hdir_src		info[AUFS_MVDOWN_UPPER].hdir
+#define mvd_h_src_dir		info[AUFS_MVDOWN_UPPER].h_dir
+#define mvd_h_src_inode		info[AUFS_MVDOWN_UPPER].h_inode
+#define mvd_pin_src		info[AUFS_MVDOWN_UPPER].pin
+
+#define mvd_h_dst_sb		info[AUFS_MVDOWN_LOWER].h_sb
+#define mvd_h_dst_parent	info[AUFS_MVDOWN_LOWER].h_parent
+#define mvd_hdir_dst		info[AUFS_MVDOWN_LOWER].hdir
+#define mvd_h_dst_dir		info[AUFS_MVDOWN_LOWER].h_dir
+#define mvd_h_dst_inode		info[AUFS_MVDOWN_LOWER].h_inode
+#define mvd_pin_dst		info[AUFS_MVDOWN_LOWER].pin
+
+#define AU_MVD_PR(flag, ...) do {			\
+		if (flag)				\
+			pr_err(__VA_ARGS__);		\
+	} while (0)
+
+static int find_lower_writable(struct au_mvd_args *a)
+{
+	struct super_block *sb;
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+
+	sb = a->sb;
+	bindex = a->mvd_bsrc;
+	bbot = au_sbbot(sb);
+	if (a->mvdown.flags & AUFS_MVDOWN_FHSM_LOWER)
+		for (bindex++; bindex <= bbot; bindex++) {
+			br = au_sbr(sb, bindex);
+			if (au_br_fhsm(br->br_perm)
+			    && !sb_rdonly(au_br_sb(br)))
+				return bindex;
+		}
+	else if (!(a->mvdown.flags & AUFS_MVDOWN_ROLOWER))
+		for (bindex++; bindex <= bbot; bindex++) {
+			br = au_sbr(sb, bindex);
+			if (!au_br_rdonly(br))
+				return bindex;
+		}
+	else
+		for (bindex++; bindex <= bbot; bindex++) {
+			br = au_sbr(sb, bindex);
+			if (!sb_rdonly(au_br_sb(br))) {
+				if (au_br_rdonly(br))
+					a->mvdown.flags
+						|= AUFS_MVDOWN_ROLOWER_R;
+				return bindex;
+			}
+		}
+
+	return -1;
+}
+
+/* make the parent dir on bdst */
+static int au_do_mkdir(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+
+	err = 0;
+	a->mvd_hdir_src = au_hi(a->dir, a->mvd_bsrc);
+	a->mvd_hdir_dst = au_hi(a->dir, a->mvd_bdst);
+	a->mvd_h_src_parent = au_h_dptr(a->parent, a->mvd_bsrc);
+	a->mvd_h_dst_parent = NULL;
+	if (au_dbbot(a->parent) >= a->mvd_bdst)
+		a->mvd_h_dst_parent = au_h_dptr(a->parent, a->mvd_bdst);
+	if (!a->mvd_h_dst_parent) {
+		err = au_cpdown_dirs(a->dentry, a->mvd_bdst);
+		if (unlikely(err)) {
+			AU_MVD_PR(dmsg, "cpdown_dirs failed\n");
+			goto out;
+		}
+		a->mvd_h_dst_parent = au_h_dptr(a->parent, a->mvd_bdst);
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* lock them all */
+static int au_do_lock(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+	struct dentry *h_trap;
+
+	a->mvd_h_src_sb = au_sbr_sb(a->sb, a->mvd_bsrc);
+	a->mvd_h_dst_sb = au_sbr_sb(a->sb, a->mvd_bdst);
+	err = au_pin(&a->mvd_pin_dst, a->dentry, a->mvd_bdst,
+		     au_opt_udba(a->sb),
+		     AuPin_MNT_WRITE | AuPin_DI_LOCKED);
+	AuTraceErr(err);
+	if (unlikely(err)) {
+		AU_MVD_PR(dmsg, "pin_dst failed\n");
+		goto out;
+	}
+
+	if (a->mvd_h_src_sb != a->mvd_h_dst_sb) {
+		a->rename_lock = 0;
+		au_pin_init(&a->mvd_pin_src, a->dentry, a->mvd_bsrc,
+			    AuLsc_DI_PARENT, AuLsc_I_PARENT3,
+			    au_opt_udba(a->sb),
+			    AuPin_MNT_WRITE | AuPin_DI_LOCKED);
+		err = au_do_pin(&a->mvd_pin_src);
+		AuTraceErr(err);
+		a->mvd_h_src_dir = d_inode(a->mvd_h_src_parent);
+		if (unlikely(err)) {
+			AU_MVD_PR(dmsg, "pin_src failed\n");
+			goto out_dst;
+		}
+		goto out; /* success */
+	}
+
+	a->rename_lock = 1;
+	au_pin_hdir_unlock(&a->mvd_pin_dst);
+	err = au_pin(&a->mvd_pin_src, a->dentry, a->mvd_bsrc,
+		     au_opt_udba(a->sb),
+		     AuPin_MNT_WRITE | AuPin_DI_LOCKED);
+	AuTraceErr(err);
+	a->mvd_h_src_dir = d_inode(a->mvd_h_src_parent);
+	if (unlikely(err)) {
+		AU_MVD_PR(dmsg, "pin_src failed\n");
+		au_pin_hdir_lock(&a->mvd_pin_dst);
+		goto out_dst;
+	}
+	au_pin_hdir_unlock(&a->mvd_pin_src);
+	h_trap = vfsub_lock_rename(a->mvd_h_src_parent, a->mvd_hdir_src,
+				   a->mvd_h_dst_parent, a->mvd_hdir_dst);
+	if (h_trap) {
+		err = (h_trap != a->mvd_h_src_parent);
+		if (err)
+			err = (h_trap != a->mvd_h_dst_parent);
+	}
+	BUG_ON(err); /* it should never happen */
+	if (unlikely(a->mvd_h_src_dir != au_pinned_h_dir(&a->mvd_pin_src))) {
+		err = -EBUSY;
+		AuTraceErr(err);
+		vfsub_unlock_rename(a->mvd_h_src_parent, a->mvd_hdir_src,
+				    a->mvd_h_dst_parent, a->mvd_hdir_dst);
+		au_pin_hdir_lock(&a->mvd_pin_src);
+		au_unpin(&a->mvd_pin_src);
+		au_pin_hdir_lock(&a->mvd_pin_dst);
+		goto out_dst;
+	}
+	goto out; /* success */
+
+out_dst:
+	au_unpin(&a->mvd_pin_dst);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static void au_do_unlock(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	if (!a->rename_lock)
+		au_unpin(&a->mvd_pin_src);
+	else {
+		vfsub_unlock_rename(a->mvd_h_src_parent, a->mvd_hdir_src,
+				    a->mvd_h_dst_parent, a->mvd_hdir_dst);
+		au_pin_hdir_lock(&a->mvd_pin_src);
+		au_unpin(&a->mvd_pin_src);
+		au_pin_hdir_lock(&a->mvd_pin_dst);
+	}
+	au_unpin(&a->mvd_pin_dst);
+}
+
+/* copy-down the file */
+static int au_do_cpdown(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+	struct au_cp_generic cpg = {
+		.dentry	= a->dentry,
+		.bdst	= a->mvd_bdst,
+		.bsrc	= a->mvd_bsrc,
+		.len	= -1,
+		.pin	= &a->mvd_pin_dst,
+		.flags	= AuCpup_DTIME | AuCpup_HOPEN
+	};
+
+	AuDbg("b%d, b%d\n", cpg.bsrc, cpg.bdst);
+	if (a->mvdown.flags & AUFS_MVDOWN_OWLOWER)
+		au_fset_cpup(cpg.flags, OVERWRITE);
+	if (a->mvdown.flags & AUFS_MVDOWN_ROLOWER)
+		au_fset_cpup(cpg.flags, RWDST);
+	err = au_sio_cpdown_simple(&cpg);
+	if (unlikely(err))
+		AU_MVD_PR(dmsg, "cpdown failed\n");
+
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * unlink the whiteout on bdst if exist which may be created by UDBA while we
+ * were sleeping
+ */
+static int au_do_unlink_wh(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+	struct path h_path;
+	struct au_branch *br;
+	struct inode *delegated;
+
+	br = au_sbr(a->sb, a->mvd_bdst);
+	h_path.dentry = au_wh_lkup(a->mvd_h_dst_parent, &a->dentry->d_name, br);
+	err = PTR_ERR(h_path.dentry);
+	if (IS_ERR(h_path.dentry)) {
+		AU_MVD_PR(dmsg, "wh_lkup failed\n");
+		goto out;
+	}
+
+	err = 0;
+	if (d_is_positive(h_path.dentry)) {
+		h_path.mnt = au_br_mnt(br);
+		delegated = NULL;
+		err = vfsub_unlink(d_inode(a->mvd_h_dst_parent), &h_path,
+				   &delegated, /*force*/0);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal unlink\n");
+			iput(delegated);
+		}
+		if (unlikely(err))
+			AU_MVD_PR(dmsg, "wh_unlink failed\n");
+	}
+	dput(h_path.dentry);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/*
+ * unlink the topmost h_dentry
+ */
+static int au_do_unlink(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+	struct path h_path;
+	struct inode *delegated;
+
+	h_path.mnt = au_sbr_mnt(a->sb, a->mvd_bsrc);
+	h_path.dentry = au_h_dptr(a->dentry, a->mvd_bsrc);
+	delegated = NULL;
+	err = vfsub_unlink(a->mvd_h_src_dir, &h_path, &delegated, /*force*/0);
+	if (unlikely(err == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal unlink\n");
+		iput(delegated);
+	}
+	if (unlikely(err))
+		AU_MVD_PR(dmsg, "unlink failed\n");
+
+	AuTraceErr(err);
+	return err;
+}
+
+/* Since mvdown succeeded, we ignore an error of this function */
+static void au_do_stfs(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+	struct au_branch *br;
+
+	a->mvdown.flags |= AUFS_MVDOWN_STFS_FAILED;
+	br = au_sbr(a->sb, a->mvd_bsrc);
+	err = au_br_stfs(br, &a->mvdown.stbr[AUFS_MVDOWN_UPPER].stfs);
+	if (!err) {
+		br = au_sbr(a->sb, a->mvd_bdst);
+		a->mvdown.stbr[AUFS_MVDOWN_LOWER].brid = br->br_id;
+		err = au_br_stfs(br, &a->mvdown.stbr[AUFS_MVDOWN_LOWER].stfs);
+	}
+	if (!err)
+		a->mvdown.flags &= ~AUFS_MVDOWN_STFS_FAILED;
+	else
+		AU_MVD_PR(dmsg, "statfs failed (%d), ignored\n", err);
+}
+
+/*
+ * copy-down the file and unlink the bsrc file.
+ * - unlink the bdst whout if exist
+ * - copy-down the file (with whtmp name and rename)
+ * - unlink the bsrc file
+ */
+static int au_do_mvdown(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+
+	err = au_do_mkdir(dmsg, a);
+	if (!err)
+		err = au_do_lock(dmsg, a);
+	if (unlikely(err))
+		goto out;
+
+	/*
+	 * do not revert the activities we made on bdst since they should be
+	 * harmless in aufs.
+	 */
+
+	err = au_do_cpdown(dmsg, a);
+	if (!err)
+		err = au_do_unlink_wh(dmsg, a);
+	if (!err && !(a->mvdown.flags & AUFS_MVDOWN_KUPPER))
+		err = au_do_unlink(dmsg, a);
+	if (unlikely(err))
+		goto out_unlock;
+
+	AuDbg("%pd2, 0x%x, %d --> %d\n",
+	      a->dentry, a->mvdown.flags, a->mvd_bsrc, a->mvd_bdst);
+	if (find_lower_writable(a) < 0)
+		a->mvdown.flags |= AUFS_MVDOWN_BOTTOM;
+
+	if (a->mvdown.flags & AUFS_MVDOWN_STFS)
+		au_do_stfs(dmsg, a);
+
+	/* maintain internal array */
+	if (!(a->mvdown.flags & AUFS_MVDOWN_KUPPER)) {
+		au_set_h_dptr(a->dentry, a->mvd_bsrc, NULL);
+		au_set_dbtop(a->dentry, a->mvd_bdst);
+		au_set_h_iptr(a->inode, a->mvd_bsrc, NULL, /*flags*/0);
+		au_set_ibtop(a->inode, a->mvd_bdst);
+	} else {
+		/* hide the lower */
+		au_set_h_dptr(a->dentry, a->mvd_bdst, NULL);
+		au_set_dbbot(a->dentry, a->mvd_bsrc);
+		au_set_h_iptr(a->inode, a->mvd_bdst, NULL, /*flags*/0);
+		au_set_ibbot(a->inode, a->mvd_bsrc);
+	}
+	if (au_dbbot(a->dentry) < a->mvd_bdst)
+		au_set_dbbot(a->dentry, a->mvd_bdst);
+	if (au_ibbot(a->inode) < a->mvd_bdst)
+		au_set_ibbot(a->inode, a->mvd_bdst);
+
+out_unlock:
+	au_do_unlock(dmsg, a);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* make sure the file is idle */
+static int au_mvd_args_busy(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err, plinked;
+
+	err = 0;
+	plinked = !!au_opt_test(au_mntflags(a->sb), PLINK);
+	if (au_dbtop(a->dentry) == a->mvd_bsrc
+	    && au_dcount(a->dentry) == 1
+	    && atomic_read(&a->inode->i_count) == 1
+	    /* && a->mvd_h_src_inode->i_nlink == 1 */
+	    && (!plinked || !au_plink_test(a->inode))
+	    && a->inode->i_nlink == 1)
+		goto out;
+
+	err = -EBUSY;
+	AU_MVD_PR(dmsg,
+		  "b%d, d{b%d, c%d?}, i{c%d?, l%u}, hi{l%u}, p{%d, %d}\n",
+		  a->mvd_bsrc, au_dbtop(a->dentry), au_dcount(a->dentry),
+		  atomic_read(&a->inode->i_count), a->inode->i_nlink,
+		  a->mvd_h_src_inode->i_nlink,
+		  plinked, plinked ? au_plink_test(a->inode) : 0);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* make sure the parent dir is fine */
+static int au_mvd_args_parent(const unsigned char dmsg,
+			      struct au_mvd_args *a)
+{
+	int err;
+	aufs_bindex_t bindex;
+
+	err = 0;
+	if (unlikely(au_alive_dir(a->parent))) {
+		err = -ENOENT;
+		AU_MVD_PR(dmsg, "parent dir is dead\n");
+		goto out;
+	}
+
+	a->bopq = au_dbdiropq(a->parent);
+	bindex = au_wbr_nonopq(a->dentry, a->mvd_bdst);
+	AuDbg("b%d\n", bindex);
+	if (unlikely((bindex >= 0 && bindex < a->mvd_bdst)
+		     || (a->bopq != -1 && a->bopq < a->mvd_bdst))) {
+		err = -EINVAL;
+		a->mvd_errno = EAU_MVDOWN_OPAQUE;
+		AU_MVD_PR(dmsg, "ancestor is opaque b%d, b%d\n",
+			  a->bopq, a->mvd_bdst);
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_mvd_args_intermediate(const unsigned char dmsg,
+				    struct au_mvd_args *a)
+{
+	int err;
+	struct au_dinfo *dinfo, *tmp;
+
+	/* lookup the next lower positive entry */
+	err = -ENOMEM;
+	tmp = au_di_alloc(a->sb, AuLsc_DI_TMP);
+	if (unlikely(!tmp))
+		goto out;
+
+	a->bfound = -1;
+	a->bwh = -1;
+	dinfo = au_di(a->dentry);
+	au_di_cp(tmp, dinfo);
+	au_di_swap(tmp, dinfo);
+
+	/* returns the number of positive dentries */
+	err = au_lkup_dentry(a->dentry, a->mvd_bsrc + 1,
+			     /* AuLkup_IGNORE_PERM */ 0);
+	if (!err)
+		a->bwh = au_dbwh(a->dentry);
+	else if (err > 0)
+		a->bfound = au_dbtop(a->dentry);
+
+	au_di_swap(tmp, dinfo);
+	au_rw_write_unlock(&tmp->di_rwsem);
+	au_di_free(tmp);
+	if (unlikely(err < 0))
+		AU_MVD_PR(dmsg, "failed look-up lower\n");
+
+	/*
+	 * here, we have these cases.
+	 * bfound == -1
+	 *	no positive dentry under bsrc. there are more sub-cases.
+	 *	bwh < 0
+	 *		there no whiteout, we can safely move-down.
+	 *	bwh <= bsrc
+	 *		impossible
+	 *	bsrc < bwh && bwh < bdst
+	 *		there is a whiteout on RO branch. cannot proceed.
+	 *	bwh == bdst
+	 *		there is a whiteout on the RW target branch. it should
+	 *		be removed.
+	 *	bdst < bwh
+	 *		there is a whiteout somewhere unrelated branch.
+	 * -1 < bfound && bfound <= bsrc
+	 *	impossible.
+	 * bfound < bdst
+	 *	found, but it is on RO branch between bsrc and bdst. cannot
+	 *	proceed.
+	 * bfound == bdst
+	 *	found, replace it if AUFS_MVDOWN_FORCE is set. otherwise return
+	 *	error.
+	 * bdst < bfound
+	 *	found, after we create the file on bdst, it will be hidden.
+	 */
+
+	AuDebugOn(a->bfound == -1
+		  && a->bwh != -1
+		  && a->bwh <= a->mvd_bsrc);
+	AuDebugOn(-1 < a->bfound
+		  && a->bfound <= a->mvd_bsrc);
+
+	err = -EINVAL;
+	if (a->bfound == -1
+	    && a->mvd_bsrc < a->bwh
+	    && a->bwh != -1
+	    && a->bwh < a->mvd_bdst) {
+		a->mvd_errno = EAU_MVDOWN_WHITEOUT;
+		AU_MVD_PR(dmsg, "bsrc %d, bdst %d, bfound %d, bwh %d\n",
+			  a->mvd_bsrc, a->mvd_bdst, a->bfound, a->bwh);
+		goto out;
+	} else if (a->bfound != -1 && a->bfound < a->mvd_bdst) {
+		a->mvd_errno = EAU_MVDOWN_UPPER;
+		AU_MVD_PR(dmsg, "bdst %d, bfound %d\n",
+			  a->mvd_bdst, a->bfound);
+		goto out;
+	}
+
+	err = 0; /* success */
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_mvd_args_exist(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+
+	err = 0;
+	if (!(a->mvdown.flags & AUFS_MVDOWN_OWLOWER)
+	    && a->bfound == a->mvd_bdst)
+		err = -EEXIST;
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_mvd_args(const unsigned char dmsg, struct au_mvd_args *a)
+{
+	int err;
+	struct au_branch *br;
+
+	err = -EISDIR;
+	if (unlikely(S_ISDIR(a->inode->i_mode)))
+		goto out;
+
+	err = -EINVAL;
+	if (!(a->mvdown.flags & AUFS_MVDOWN_BRID_UPPER))
+		a->mvd_bsrc = au_ibtop(a->inode);
+	else {
+		a->mvd_bsrc = au_br_index(a->sb, a->mvd_src_brid);
+		if (unlikely(a->mvd_bsrc < 0
+			     || (a->mvd_bsrc < au_dbtop(a->dentry)
+				 || au_dbbot(a->dentry) < a->mvd_bsrc
+				 || !au_h_dptr(a->dentry, a->mvd_bsrc))
+			     || (a->mvd_bsrc < au_ibtop(a->inode)
+				 || au_ibbot(a->inode) < a->mvd_bsrc
+				 || !au_h_iptr(a->inode, a->mvd_bsrc)))) {
+			a->mvd_errno = EAU_MVDOWN_NOUPPER;
+			AU_MVD_PR(dmsg, "no upper\n");
+			goto out;
+		}
+	}
+	if (unlikely(a->mvd_bsrc == au_sbbot(a->sb))) {
+		a->mvd_errno = EAU_MVDOWN_BOTTOM;
+		AU_MVD_PR(dmsg, "on the bottom\n");
+		goto out;
+	}
+	a->mvd_h_src_inode = au_h_iptr(a->inode, a->mvd_bsrc);
+	br = au_sbr(a->sb, a->mvd_bsrc);
+	err = au_br_rdonly(br);
+	if (!(a->mvdown.flags & AUFS_MVDOWN_ROUPPER)) {
+		if (unlikely(err))
+			goto out;
+	} else if (!(vfsub_native_ro(a->mvd_h_src_inode)
+		     || IS_APPEND(a->mvd_h_src_inode))) {
+		if (err)
+			a->mvdown.flags |= AUFS_MVDOWN_ROUPPER_R;
+		/* go on */
+	} else
+		goto out;
+
+	err = -EINVAL;
+	if (!(a->mvdown.flags & AUFS_MVDOWN_BRID_LOWER)) {
+		a->mvd_bdst = find_lower_writable(a);
+		if (unlikely(a->mvd_bdst < 0)) {
+			a->mvd_errno = EAU_MVDOWN_BOTTOM;
+			AU_MVD_PR(dmsg, "no writable lower branch\n");
+			goto out;
+		}
+	} else {
+		a->mvd_bdst = au_br_index(a->sb, a->mvd_dst_brid);
+		if (unlikely(a->mvd_bdst < 0
+			     || au_sbbot(a->sb) < a->mvd_bdst)) {
+			a->mvd_errno = EAU_MVDOWN_NOLOWERBR;
+			AU_MVD_PR(dmsg, "no lower brid\n");
+			goto out;
+		}
+	}
+
+	err = au_mvd_args_busy(dmsg, a);
+	if (!err)
+		err = au_mvd_args_parent(dmsg, a);
+	if (!err)
+		err = au_mvd_args_intermediate(dmsg, a);
+	if (!err)
+		err = au_mvd_args_exist(dmsg, a);
+	if (!err)
+		AuDbg("b%d, b%d\n", a->mvd_bsrc, a->mvd_bdst);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+int au_mvdown(struct dentry *dentry, struct aufs_mvdown __user *uarg)
+{
+	int err, e;
+	unsigned char dmsg;
+	struct au_mvd_args *args;
+	struct inode *inode;
+
+	inode = d_inode(dentry);
+	err = -EPERM;
+	if (unlikely(!capable(CAP_SYS_ADMIN)))
+		goto out;
+
+	err = -ENOMEM;
+	args = kmalloc(sizeof(*args), GFP_NOFS);
+	if (unlikely(!args))
+		goto out;
+
+	err = copy_from_user(&args->mvdown, uarg, sizeof(args->mvdown));
+	if (!err)
+		/* VERIFY_WRITE */
+		err = !access_ok(uarg, sizeof(*uarg));
+	if (unlikely(err)) {
+		err = -EFAULT;
+		AuTraceErr(err);
+		goto out_free;
+	}
+	AuDbg("flags 0x%x\n", args->mvdown.flags);
+	args->mvdown.flags &= ~(AUFS_MVDOWN_ROLOWER_R | AUFS_MVDOWN_ROUPPER_R);
+	args->mvdown.au_errno = 0;
+	args->dentry = dentry;
+	args->inode = inode;
+	args->sb = dentry->d_sb;
+
+	err = -ENOENT;
+	dmsg = !!(args->mvdown.flags & AUFS_MVDOWN_DMSG);
+	args->parent = dget_parent(dentry);
+	args->dir = d_inode(args->parent);
+	inode_lock_nested(args->dir, I_MUTEX_PARENT);
+	dput(args->parent);
+	if (unlikely(args->parent != dentry->d_parent)) {
+		AU_MVD_PR(dmsg, "parent dir is moved\n");
+		goto out_dir;
+	}
+
+	inode_lock_nested(inode, I_MUTEX_CHILD);
+	err = aufs_read_lock(dentry, AuLock_DW | AuLock_FLUSH | AuLock_NOPLMW);
+	if (unlikely(err))
+		goto out_inode;
+
+	di_write_lock_parent(args->parent);
+	err = au_mvd_args(dmsg, args);
+	if (unlikely(err))
+		goto out_parent;
+
+	err = au_do_mvdown(dmsg, args);
+	if (unlikely(err))
+		goto out_parent;
+
+	au_cpup_attr_timesizes(args->dir);
+	au_cpup_attr_timesizes(inode);
+	if (!(args->mvdown.flags & AUFS_MVDOWN_KUPPER))
+		au_cpup_igen(inode, au_h_iptr(inode, args->mvd_bdst));
+	/* au_digen_dec(dentry); */
+
+out_parent:
+	di_write_unlock(args->parent);
+	aufs_read_unlock(dentry, AuLock_DW);
+out_inode:
+	inode_unlock(inode);
+out_dir:
+	inode_unlock(args->dir);
+out_free:
+	e = copy_to_user(uarg, &args->mvdown, sizeof(args->mvdown));
+	if (unlikely(e))
+		err = -EFAULT;
+	au_kfree_rcu(args);
+out:
+	AuTraceErr(err);
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/opts.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/opts.c
@@ -0,0 +1,1880 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * mount options/flags
+ */
+
+#include <linux/namei.h>
+#include <linux/types.h> /* a distribution requires */
+#include <linux/parser.h>
+#include "aufs.h"
+
+/* ---------------------------------------------------------------------- */
+
+enum {
+	Opt_br,
+	Opt_add, Opt_del, Opt_mod, Opt_append, Opt_prepend,
+	Opt_idel, Opt_imod,
+	Opt_dirwh, Opt_rdcache, Opt_rdblk, Opt_rdhash,
+	Opt_rdblk_def, Opt_rdhash_def,
+	Opt_xino, Opt_noxino,
+	Opt_trunc_xino, Opt_trunc_xino_v, Opt_notrunc_xino,
+	Opt_trunc_xino_path, Opt_itrunc_xino,
+	Opt_trunc_xib, Opt_notrunc_xib,
+	Opt_shwh, Opt_noshwh,
+	Opt_plink, Opt_noplink, Opt_list_plink,
+	Opt_udba,
+	Opt_dio, Opt_nodio,
+	Opt_diropq_a, Opt_diropq_w,
+	Opt_warn_perm, Opt_nowarn_perm,
+	Opt_wbr_copyup, Opt_wbr_create,
+	Opt_fhsm_sec,
+	Opt_verbose, Opt_noverbose,
+	Opt_sum, Opt_nosum, Opt_wsum,
+	Opt_dirperm1, Opt_nodirperm1,
+	Opt_dirren, Opt_nodirren,
+	Opt_acl, Opt_noacl,
+	Opt_tail, Opt_ignore, Opt_ignore_silent, Opt_err
+};
+
+static match_table_t options = {
+	{Opt_br, "br=%s"},
+	{Opt_br, "br:%s"},
+
+	{Opt_add, "add=%d:%s"},
+	{Opt_add, "add:%d:%s"},
+	{Opt_add, "ins=%d:%s"},
+	{Opt_add, "ins:%d:%s"},
+	{Opt_append, "append=%s"},
+	{Opt_append, "append:%s"},
+	{Opt_prepend, "prepend=%s"},
+	{Opt_prepend, "prepend:%s"},
+
+	{Opt_del, "del=%s"},
+	{Opt_del, "del:%s"},
+	/* {Opt_idel, "idel:%d"}, */
+	{Opt_mod, "mod=%s"},
+	{Opt_mod, "mod:%s"},
+	/* {Opt_imod, "imod:%d:%s"}, */
+
+	{Opt_dirwh, "dirwh=%d"},
+
+	{Opt_xino, "xino=%s"},
+	{Opt_noxino, "noxino"},
+	{Opt_trunc_xino, "trunc_xino"},
+	{Opt_trunc_xino_v, "trunc_xino_v=%d:%d"},
+	{Opt_notrunc_xino, "notrunc_xino"},
+	{Opt_trunc_xino_path, "trunc_xino=%s"},
+	{Opt_itrunc_xino, "itrunc_xino=%d"},
+	/* {Opt_zxino, "zxino=%s"}, */
+	{Opt_trunc_xib, "trunc_xib"},
+	{Opt_notrunc_xib, "notrunc_xib"},
+
+#ifdef CONFIG_PROC_FS
+	{Opt_plink, "plink"},
+#else
+	{Opt_ignore_silent, "plink"},
+#endif
+
+	{Opt_noplink, "noplink"},
+
+#ifdef CONFIG_AUFS_DEBUG
+	{Opt_list_plink, "list_plink"},
+#endif
+
+	{Opt_udba, "udba=%s"},
+
+	{Opt_dio, "dio"},
+	{Opt_nodio, "nodio"},
+
+#ifdef CONFIG_AUFS_DIRREN
+	{Opt_dirren, "dirren"},
+	{Opt_nodirren, "nodirren"},
+#else
+	{Opt_ignore, "dirren"},
+	{Opt_ignore_silent, "nodirren"},
+#endif
+
+#ifdef CONFIG_AUFS_FHSM
+	{Opt_fhsm_sec, "fhsm_sec=%d"},
+#else
+	{Opt_ignore, "fhsm_sec=%d"},
+#endif
+
+	{Opt_diropq_a, "diropq=always"},
+	{Opt_diropq_a, "diropq=a"},
+	{Opt_diropq_w, "diropq=whiteouted"},
+	{Opt_diropq_w, "diropq=w"},
+
+	{Opt_warn_perm, "warn_perm"},
+	{Opt_nowarn_perm, "nowarn_perm"},
+
+	/* keep them temporary */
+	{Opt_ignore_silent, "nodlgt"},
+	{Opt_ignore, "clean_plink"},
+
+#ifdef CONFIG_AUFS_SHWH
+	{Opt_shwh, "shwh"},
+#endif
+	{Opt_noshwh, "noshwh"},
+
+	{Opt_dirperm1, "dirperm1"},
+	{Opt_nodirperm1, "nodirperm1"},
+
+	{Opt_verbose, "verbose"},
+	{Opt_verbose, "v"},
+	{Opt_noverbose, "noverbose"},
+	{Opt_noverbose, "quiet"},
+	{Opt_noverbose, "q"},
+	{Opt_noverbose, "silent"},
+
+	{Opt_sum, "sum"},
+	{Opt_nosum, "nosum"},
+	{Opt_wsum, "wsum"},
+
+	{Opt_rdcache, "rdcache=%d"},
+	{Opt_rdblk, "rdblk=%d"},
+	{Opt_rdblk_def, "rdblk=def"},
+	{Opt_rdhash, "rdhash=%d"},
+	{Opt_rdhash_def, "rdhash=def"},
+
+	{Opt_wbr_create, "create=%s"},
+	{Opt_wbr_create, "create_policy=%s"},
+	{Opt_wbr_copyup, "cpup=%s"},
+	{Opt_wbr_copyup, "copyup=%s"},
+	{Opt_wbr_copyup, "copyup_policy=%s"},
+
+	/* generic VFS flag */
+#ifdef CONFIG_FS_POSIX_ACL
+	{Opt_acl, "acl"},
+	{Opt_noacl, "noacl"},
+#else
+	{Opt_ignore, "acl"},
+	{Opt_ignore_silent, "noacl"},
+#endif
+
+	/* internal use for the scripts */
+	{Opt_ignore_silent, "si=%s"},
+
+	{Opt_br, "dirs=%s"},
+	{Opt_ignore, "debug=%d"},
+	{Opt_ignore, "delete=whiteout"},
+	{Opt_ignore, "delete=all"},
+	{Opt_ignore, "imap=%s"},
+
+	/* temporary workaround, due to old mount(8)? */
+	{Opt_ignore_silent, "relatime"},
+
+	{Opt_err, NULL}
+};
+
+/* ---------------------------------------------------------------------- */
+
+static const char *au_parser_pattern(int val, match_table_t tbl)
+{
+	struct match_token *p;
+
+	p = tbl;
+	while (p->pattern) {
+		if (p->token == val)
+			return p->pattern;
+		p++;
+	}
+	BUG();
+	return "??";
+}
+
+static const char *au_optstr(int *val, match_table_t tbl)
+{
+	struct match_token *p;
+	int v;
+
+	v = *val;
+	if (!v)
+		goto out;
+	p = tbl;
+	while (p->pattern) {
+		if (p->token
+		    && (v & p->token) == p->token) {
+			*val &= ~p->token;
+			return p->pattern;
+		}
+		p++;
+	}
+
+out:
+	return NULL;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static match_table_t brperm = {
+	{AuBrPerm_RO, AUFS_BRPERM_RO},
+	{AuBrPerm_RR, AUFS_BRPERM_RR},
+	{AuBrPerm_RW, AUFS_BRPERM_RW},
+	{0, NULL}
+};
+
+static match_table_t brattr = {
+	/* general */
+	{AuBrAttr_COO_REG, AUFS_BRATTR_COO_REG},
+	{AuBrAttr_COO_ALL, AUFS_BRATTR_COO_ALL},
+	/* 'unpin' attrib is meaningless since linux-3.18-rc1 */
+	{AuBrAttr_UNPIN, AUFS_BRATTR_UNPIN},
+#ifdef CONFIG_AUFS_FHSM
+	{AuBrAttr_FHSM, AUFS_BRATTR_FHSM},
+#endif
+#ifdef CONFIG_AUFS_XATTR
+	{AuBrAttr_ICEX, AUFS_BRATTR_ICEX},
+	{AuBrAttr_ICEX_SEC, AUFS_BRATTR_ICEX_SEC},
+	{AuBrAttr_ICEX_SYS, AUFS_BRATTR_ICEX_SYS},
+	{AuBrAttr_ICEX_TR, AUFS_BRATTR_ICEX_TR},
+	{AuBrAttr_ICEX_USR, AUFS_BRATTR_ICEX_USR},
+	{AuBrAttr_ICEX_OTH, AUFS_BRATTR_ICEX_OTH},
+#endif
+
+	/* ro/rr branch */
+	{AuBrRAttr_WH, AUFS_BRRATTR_WH},
+
+	/* rw branch */
+	{AuBrWAttr_MOO, AUFS_BRWATTR_MOO},
+	{AuBrWAttr_NoLinkWH, AUFS_BRWATTR_NLWH},
+
+	{0, NULL}
+};
+
+static int br_attr_val(char *str, match_table_t table, substring_t args[])
+{
+	int attr, v;
+	char *p;
+
+	attr = 0;
+	do {
+		p = strchr(str, '+');
+		if (p)
+			*p = 0;
+		v = match_token(str, table, args);
+		if (v) {
+			if (v & AuBrAttr_CMOO_Mask)
+				attr &= ~AuBrAttr_CMOO_Mask;
+			attr |= v;
+		} else {
+			if (p)
+				*p = '+';
+			pr_warn("ignored branch attribute %s\n", str);
+			break;
+		}
+		if (p)
+			str = p + 1;
+	} while (p);
+
+	return attr;
+}
+
+static int au_do_optstr_br_attr(au_br_perm_str_t *str, int perm)
+{
+	int sz;
+	const char *p;
+	char *q;
+
+	q = str->a;
+	*q = 0;
+	p = au_optstr(&perm, brattr);
+	if (p) {
+		sz = strlen(p);
+		memcpy(q, p, sz + 1);
+		q += sz;
+	} else
+		goto out;
+
+	do {
+		p = au_optstr(&perm, brattr);
+		if (p) {
+			*q++ = '+';
+			sz = strlen(p);
+			memcpy(q, p, sz + 1);
+			q += sz;
+		}
+	} while (p);
+
+out:
+	return q - str->a;
+}
+
+static int noinline_for_stack br_perm_val(char *perm)
+{
+	int val, bad, sz;
+	char *p;
+	substring_t args[MAX_OPT_ARGS];
+	au_br_perm_str_t attr;
+
+	p = strchr(perm, '+');
+	if (p)
+		*p = 0;
+	val = match_token(perm, brperm, args);
+	if (!val) {
+		if (p)
+			*p = '+';
+		pr_warn("ignored branch permission %s\n", perm);
+		val = AuBrPerm_RO;
+		goto out;
+	}
+	if (!p)
+		goto out;
+
+	val |= br_attr_val(p + 1, brattr, args);
+
+	bad = 0;
+	switch (val & AuBrPerm_Mask) {
+	case AuBrPerm_RO:
+	case AuBrPerm_RR:
+		bad = val & AuBrWAttr_Mask;
+		val &= ~AuBrWAttr_Mask;
+		break;
+	case AuBrPerm_RW:
+		bad = val & AuBrRAttr_Mask;
+		val &= ~AuBrRAttr_Mask;
+		break;
+	}
+
+	/*
+	 * 'unpin' attrib becomes meaningless since linux-3.18-rc1, but aufs
+	 * does not treat it as an error, just warning.
+	 * this is a tiny guard for the user operation.
+	 */
+	if (val & AuBrAttr_UNPIN) {
+		bad |= AuBrAttr_UNPIN;
+		val &= ~AuBrAttr_UNPIN;
+	}
+
+	if (unlikely(bad)) {
+		sz = au_do_optstr_br_attr(&attr, bad);
+		AuDebugOn(!sz);
+		pr_warn("ignored branch attribute %s\n", attr.a);
+	}
+
+out:
+	return val;
+}
+
+void au_optstr_br_perm(au_br_perm_str_t *str, int perm)
+{
+	au_br_perm_str_t attr;
+	const char *p;
+	char *q;
+	int sz;
+
+	q = str->a;
+	p = au_optstr(&perm, brperm);
+	AuDebugOn(!p || !*p);
+	sz = strlen(p);
+	memcpy(q, p, sz + 1);
+	q += sz;
+
+	sz = au_do_optstr_br_attr(&attr, perm);
+	if (sz) {
+		*q++ = '+';
+		memcpy(q, attr.a, sz + 1);
+	}
+
+	AuDebugOn(strlen(str->a) >= sizeof(str->a));
+}
+
+/* ---------------------------------------------------------------------- */
+
+static match_table_t udbalevel = {
+	{AuOpt_UDBA_REVAL, "reval"},
+	{AuOpt_UDBA_NONE, "none"},
+#ifdef CONFIG_AUFS_HNOTIFY
+	{AuOpt_UDBA_HNOTIFY, "notify"}, /* abstraction */
+#ifdef CONFIG_AUFS_HFSNOTIFY
+	{AuOpt_UDBA_HNOTIFY, "fsnotify"},
+#endif
+#endif
+	{-1, NULL}
+};
+
+static int noinline_for_stack udba_val(char *str)
+{
+	substring_t args[MAX_OPT_ARGS];
+
+	return match_token(str, udbalevel, args);
+}
+
+const char *au_optstr_udba(int udba)
+{
+	return au_parser_pattern(udba, udbalevel);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static match_table_t au_wbr_create_policy = {
+	{AuWbrCreate_TDP, "tdp"},
+	{AuWbrCreate_TDP, "top-down-parent"},
+	{AuWbrCreate_RR, "rr"},
+	{AuWbrCreate_RR, "round-robin"},
+	{AuWbrCreate_MFS, "mfs"},
+	{AuWbrCreate_MFS, "most-free-space"},
+	{AuWbrCreate_MFSV, "mfs:%d"},
+	{AuWbrCreate_MFSV, "most-free-space:%d"},
+
+	/* top-down regardless the parent, and then mfs */
+	{AuWbrCreate_TDMFS, "tdmfs:%d"},
+	{AuWbrCreate_TDMFSV, "tdmfs:%d:%d"},
+
+	{AuWbrCreate_MFSRR, "mfsrr:%d"},
+	{AuWbrCreate_MFSRRV, "mfsrr:%d:%d"},
+	{AuWbrCreate_PMFS, "pmfs"},
+	{AuWbrCreate_PMFSV, "pmfs:%d"},
+	{AuWbrCreate_PMFSRR, "pmfsrr:%d"},
+	{AuWbrCreate_PMFSRRV, "pmfsrr:%d:%d"},
+
+	{-1, NULL}
+};
+
+static int au_wbr_mfs_wmark(substring_t *arg, char *str,
+			    struct au_opt_wbr_create *create)
+{
+	int err;
+	unsigned long long ull;
+
+	err = 0;
+	if (!match_u64(arg, &ull))
+		create->mfsrr_watermark = ull;
+	else {
+		pr_err("bad integer in %s\n", str);
+		err = -EINVAL;
+	}
+
+	return err;
+}
+
+static int au_wbr_mfs_sec(substring_t *arg, char *str,
+			  struct au_opt_wbr_create *create)
+{
+	int n, err;
+
+	err = 0;
+	if (!match_int(arg, &n) && 0 <= n && n <= AUFS_MFS_MAX_SEC)
+		create->mfs_second = n;
+	else {
+		pr_err("bad integer in %s\n", str);
+		err = -EINVAL;
+	}
+
+	return err;
+}
+
+static int noinline_for_stack
+au_wbr_create_val(char *str, struct au_opt_wbr_create *create)
+{
+	int err, e;
+	substring_t args[MAX_OPT_ARGS];
+
+	err = match_token(str, au_wbr_create_policy, args);
+	create->wbr_create = err;
+	switch (err) {
+	case AuWbrCreate_MFSRRV:
+	case AuWbrCreate_TDMFSV:
+	case AuWbrCreate_PMFSRRV:
+		e = au_wbr_mfs_wmark(&args[0], str, create);
+		if (!e)
+			e = au_wbr_mfs_sec(&args[1], str, create);
+		if (unlikely(e))
+			err = e;
+		break;
+	case AuWbrCreate_MFSRR:
+	case AuWbrCreate_TDMFS:
+	case AuWbrCreate_PMFSRR:
+		e = au_wbr_mfs_wmark(&args[0], str, create);
+		if (unlikely(e)) {
+			err = e;
+			break;
+		}
+		fallthrough;
+	case AuWbrCreate_MFS:
+	case AuWbrCreate_PMFS:
+		create->mfs_second = AUFS_MFS_DEF_SEC;
+		break;
+	case AuWbrCreate_MFSV:
+	case AuWbrCreate_PMFSV:
+		e = au_wbr_mfs_sec(&args[0], str, create);
+		if (unlikely(e))
+			err = e;
+		break;
+	}
+
+	return err;
+}
+
+const char *au_optstr_wbr_create(int wbr_create)
+{
+	return au_parser_pattern(wbr_create, au_wbr_create_policy);
+}
+
+static match_table_t au_wbr_copyup_policy = {
+	{AuWbrCopyup_TDP, "tdp"},
+	{AuWbrCopyup_TDP, "top-down-parent"},
+	{AuWbrCopyup_BUP, "bup"},
+	{AuWbrCopyup_BUP, "bottom-up-parent"},
+	{AuWbrCopyup_BU, "bu"},
+	{AuWbrCopyup_BU, "bottom-up"},
+	{-1, NULL}
+};
+
+static int noinline_for_stack au_wbr_copyup_val(char *str)
+{
+	substring_t args[MAX_OPT_ARGS];
+
+	return match_token(str, au_wbr_copyup_policy, args);
+}
+
+const char *au_optstr_wbr_copyup(int wbr_copyup)
+{
+	return au_parser_pattern(wbr_copyup, au_wbr_copyup_policy);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static const int lkup_dirflags = LOOKUP_FOLLOW | LOOKUP_DIRECTORY;
+
+static void dump_opts(struct au_opts *opts)
+{
+#ifdef CONFIG_AUFS_DEBUG
+	/* reduce stack space */
+	union {
+		struct au_opt_add *add;
+		struct au_opt_del *del;
+		struct au_opt_mod *mod;
+		struct au_opt_xino *xino;
+		struct au_opt_xino_itrunc *xino_itrunc;
+		struct au_opt_wbr_create *create;
+	} u;
+	struct au_opt *opt;
+
+	opt = opts->opt;
+	while (opt->type != Opt_tail) {
+		switch (opt->type) {
+		case Opt_add:
+			u.add = &opt->add;
+			AuDbg("add {b%d, %s, 0x%x, %p}\n",
+				  u.add->bindex, u.add->pathname, u.add->perm,
+				  u.add->path.dentry);
+			break;
+		case Opt_del:
+		case Opt_idel:
+			u.del = &opt->del;
+			AuDbg("del {%s, %p}\n",
+			      u.del->pathname, u.del->h_path.dentry);
+			break;
+		case Opt_mod:
+		case Opt_imod:
+			u.mod = &opt->mod;
+			AuDbg("mod {%s, 0x%x, %p}\n",
+				  u.mod->path, u.mod->perm, u.mod->h_root);
+			break;
+		case Opt_append:
+			u.add = &opt->add;
+			AuDbg("append {b%d, %s, 0x%x, %p}\n",
+				  u.add->bindex, u.add->pathname, u.add->perm,
+				  u.add->path.dentry);
+			break;
+		case Opt_prepend:
+			u.add = &opt->add;
+			AuDbg("prepend {b%d, %s, 0x%x, %p}\n",
+				  u.add->bindex, u.add->pathname, u.add->perm,
+				  u.add->path.dentry);
+			break;
+		case Opt_dirwh:
+			AuDbg("dirwh %d\n", opt->dirwh);
+			break;
+		case Opt_rdcache:
+			AuDbg("rdcache %d\n", opt->rdcache);
+			break;
+		case Opt_rdblk:
+			AuDbg("rdblk %u\n", opt->rdblk);
+			break;
+		case Opt_rdblk_def:
+			AuDbg("rdblk_def\n");
+			break;
+		case Opt_rdhash:
+			AuDbg("rdhash %u\n", opt->rdhash);
+			break;
+		case Opt_rdhash_def:
+			AuDbg("rdhash_def\n");
+			break;
+		case Opt_xino:
+			u.xino = &opt->xino;
+			AuDbg("xino {%s %pD}\n", u.xino->path, u.xino->file);
+			break;
+		case Opt_trunc_xino:
+			AuLabel(trunc_xino);
+			break;
+		case Opt_notrunc_xino:
+			AuLabel(notrunc_xino);
+			break;
+		case Opt_trunc_xino_path:
+		case Opt_itrunc_xino:
+			u.xino_itrunc = &opt->xino_itrunc;
+			AuDbg("trunc_xino %d\n", u.xino_itrunc->bindex);
+			break;
+		case Opt_noxino:
+			AuLabel(noxino);
+			break;
+		case Opt_trunc_xib:
+			AuLabel(trunc_xib);
+			break;
+		case Opt_notrunc_xib:
+			AuLabel(notrunc_xib);
+			break;
+		case Opt_shwh:
+			AuLabel(shwh);
+			break;
+		case Opt_noshwh:
+			AuLabel(noshwh);
+			break;
+		case Opt_dirperm1:
+			AuLabel(dirperm1);
+			break;
+		case Opt_nodirperm1:
+			AuLabel(nodirperm1);
+			break;
+		case Opt_plink:
+			AuLabel(plink);
+			break;
+		case Opt_noplink:
+			AuLabel(noplink);
+			break;
+		case Opt_list_plink:
+			AuLabel(list_plink);
+			break;
+		case Opt_udba:
+			AuDbg("udba %d, %s\n",
+				  opt->udba, au_optstr_udba(opt->udba));
+			break;
+		case Opt_dio:
+			AuLabel(dio);
+			break;
+		case Opt_nodio:
+			AuLabel(nodio);
+			break;
+		case Opt_diropq_a:
+			AuLabel(diropq_a);
+			break;
+		case Opt_diropq_w:
+			AuLabel(diropq_w);
+			break;
+		case Opt_warn_perm:
+			AuLabel(warn_perm);
+			break;
+		case Opt_nowarn_perm:
+			AuLabel(nowarn_perm);
+			break;
+		case Opt_verbose:
+			AuLabel(verbose);
+			break;
+		case Opt_noverbose:
+			AuLabel(noverbose);
+			break;
+		case Opt_sum:
+			AuLabel(sum);
+			break;
+		case Opt_nosum:
+			AuLabel(nosum);
+			break;
+		case Opt_wsum:
+			AuLabel(wsum);
+			break;
+		case Opt_wbr_create:
+			u.create = &opt->wbr_create;
+			AuDbg("create %d, %s\n", u.create->wbr_create,
+				  au_optstr_wbr_create(u.create->wbr_create));
+			switch (u.create->wbr_create) {
+			case AuWbrCreate_MFSV:
+			case AuWbrCreate_PMFSV:
+				AuDbg("%d sec\n", u.create->mfs_second);
+				break;
+			case AuWbrCreate_MFSRR:
+			case AuWbrCreate_TDMFS:
+				AuDbg("%llu watermark\n",
+					  u.create->mfsrr_watermark);
+				break;
+			case AuWbrCreate_MFSRRV:
+			case AuWbrCreate_TDMFSV:
+			case AuWbrCreate_PMFSRRV:
+				AuDbg("%llu watermark, %d sec\n",
+					  u.create->mfsrr_watermark,
+					  u.create->mfs_second);
+				break;
+			}
+			break;
+		case Opt_wbr_copyup:
+			AuDbg("copyup %d, %s\n", opt->wbr_copyup,
+				  au_optstr_wbr_copyup(opt->wbr_copyup));
+			break;
+		case Opt_fhsm_sec:
+			AuDbg("fhsm_sec %u\n", opt->fhsm_second);
+			break;
+		case Opt_dirren:
+			AuLabel(dirren);
+			break;
+		case Opt_nodirren:
+			AuLabel(nodirren);
+			break;
+		case Opt_acl:
+			AuLabel(acl);
+			break;
+		case Opt_noacl:
+			AuLabel(noacl);
+			break;
+		default:
+			BUG();
+		}
+		opt++;
+	}
+#endif
+}
+
+void au_opts_free(struct au_opts *opts)
+{
+	struct au_opt *opt;
+
+	opt = opts->opt;
+	while (opt->type != Opt_tail) {
+		switch (opt->type) {
+		case Opt_add:
+		case Opt_append:
+		case Opt_prepend:
+			path_put(&opt->add.path);
+			break;
+		case Opt_del:
+		case Opt_idel:
+			path_put(&opt->del.h_path);
+			break;
+		case Opt_mod:
+		case Opt_imod:
+			dput(opt->mod.h_root);
+			break;
+		case Opt_xino:
+			fput(opt->xino.file);
+			break;
+		}
+		opt++;
+	}
+}
+
+static int opt_add(struct au_opt *opt, char *opt_str, unsigned long sb_flags,
+		   aufs_bindex_t bindex)
+{
+	int err;
+	struct au_opt_add *add = &opt->add;
+	char *p;
+
+	add->bindex = bindex;
+	add->perm = AuBrPerm_RO;
+	add->pathname = opt_str;
+	p = strchr(opt_str, '=');
+	if (p) {
+		*p++ = 0;
+		if (*p)
+			add->perm = br_perm_val(p);
+	}
+
+	err = vfsub_kern_path(add->pathname, lkup_dirflags, &add->path);
+	if (!err) {
+		if (!p) {
+			add->perm = AuBrPerm_RO;
+			if (au_test_fs_rr(add->path.dentry->d_sb))
+				add->perm = AuBrPerm_RR;
+			else if (!bindex && !(sb_flags & SB_RDONLY))
+				add->perm = AuBrPerm_RW;
+		}
+		opt->type = Opt_add;
+		goto out;
+	}
+	pr_err("lookup failed %s (%d)\n", add->pathname, err);
+	err = -EINVAL;
+
+out:
+	return err;
+}
+
+static int au_opts_parse_del(struct au_opt_del *del, substring_t args[])
+{
+	int err;
+
+	del->pathname = args[0].from;
+	AuDbg("del path %s\n", del->pathname);
+
+	err = vfsub_kern_path(del->pathname, lkup_dirflags, &del->h_path);
+	if (unlikely(err))
+		pr_err("lookup failed %s (%d)\n", del->pathname, err);
+
+	return err;
+}
+
+#if 0 /* reserved for future use */
+static int au_opts_parse_idel(struct super_block *sb, aufs_bindex_t bindex,
+			      struct au_opt_del *del, substring_t args[])
+{
+	int err;
+	struct dentry *root;
+
+	err = -EINVAL;
+	root = sb->s_root;
+	aufs_read_lock(root, AuLock_FLUSH);
+	if (bindex < 0 || au_sbbot(sb) < bindex) {
+		pr_err("out of bounds, %d\n", bindex);
+		goto out;
+	}
+
+	err = 0;
+	del->h_path.dentry = dget(au_h_dptr(root, bindex));
+	del->h_path.mnt = mntget(au_sbr_mnt(sb, bindex));
+
+out:
+	aufs_read_unlock(root, !AuLock_IR);
+	return err;
+}
+#endif
+
+static int noinline_for_stack
+au_opts_parse_mod(struct au_opt_mod *mod, substring_t args[])
+{
+	int err;
+	struct path path;
+	char *p;
+
+	err = -EINVAL;
+	mod->path = args[0].from;
+	p = strchr(mod->path, '=');
+	if (unlikely(!p)) {
+		pr_err("no permission %s\n", args[0].from);
+		goto out;
+	}
+
+	*p++ = 0;
+	err = vfsub_kern_path(mod->path, lkup_dirflags, &path);
+	if (unlikely(err)) {
+		pr_err("lookup failed %s (%d)\n", mod->path, err);
+		goto out;
+	}
+
+	mod->perm = br_perm_val(p);
+	AuDbg("mod path %s, perm 0x%x, %s\n", mod->path, mod->perm, p);
+	mod->h_root = dget(path.dentry);
+	path_put(&path);
+
+out:
+	return err;
+}
+
+#if 0 /* reserved for future use */
+static int au_opts_parse_imod(struct super_block *sb, aufs_bindex_t bindex,
+			      struct au_opt_mod *mod, substring_t args[])
+{
+	int err;
+	struct dentry *root;
+
+	err = -EINVAL;
+	root = sb->s_root;
+	aufs_read_lock(root, AuLock_FLUSH);
+	if (bindex < 0 || au_sbbot(sb) < bindex) {
+		pr_err("out of bounds, %d\n", bindex);
+		goto out;
+	}
+
+	err = 0;
+	mod->perm = br_perm_val(args[1].from);
+	AuDbg("mod path %s, perm 0x%x, %s\n",
+	      mod->path, mod->perm, args[1].from);
+	mod->h_root = dget(au_h_dptr(root, bindex));
+
+out:
+	aufs_read_unlock(root, !AuLock_IR);
+	return err;
+}
+#endif
+
+static int au_opts_parse_xino(struct super_block *sb, struct au_opt_xino *xino,
+			      substring_t args[])
+{
+	int err;
+	struct file *file;
+
+	file = au_xino_create(sb, args[0].from, /*silent*/0, /*wbrtop*/0);
+	err = PTR_ERR(file);
+	if (IS_ERR(file))
+		goto out;
+
+	err = -EINVAL;
+	if (unlikely(file->f_path.dentry->d_sb == sb)) {
+		fput(file);
+		pr_err("%s must be outside\n", args[0].from);
+		goto out;
+	}
+
+	err = 0;
+	xino->file = file;
+	xino->path = args[0].from;
+
+out:
+	return err;
+}
+
+static int noinline_for_stack
+au_opts_parse_xino_itrunc_path(struct super_block *sb,
+			       struct au_opt_xino_itrunc *xino_itrunc,
+			       substring_t args[])
+{
+	int err;
+	aufs_bindex_t bbot, bindex;
+	struct path path;
+	struct dentry *root;
+
+	err = vfsub_kern_path(args[0].from, lkup_dirflags, &path);
+	if (unlikely(err)) {
+		pr_err("lookup failed %s (%d)\n", args[0].from, err);
+		goto out;
+	}
+
+	xino_itrunc->bindex = -1;
+	root = sb->s_root;
+	aufs_read_lock(root, AuLock_FLUSH);
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		if (au_h_dptr(root, bindex) == path.dentry) {
+			xino_itrunc->bindex = bindex;
+			break;
+		}
+	}
+	aufs_read_unlock(root, !AuLock_IR);
+	path_put(&path);
+
+	if (unlikely(xino_itrunc->bindex < 0)) {
+		pr_err("no such branch %s\n", args[0].from);
+		err = -EINVAL;
+	}
+
+out:
+	return err;
+}
+
+/* called without aufs lock */
+int au_opts_parse(struct super_block *sb, char *str, struct au_opts *opts)
+{
+	int err, n, token;
+	aufs_bindex_t bindex;
+	unsigned char skipped;
+	struct dentry *root;
+	struct au_opt *opt, *opt_tail;
+	char *opt_str;
+	/* reduce the stack space */
+	union {
+		struct au_opt_xino_itrunc *xino_itrunc;
+		struct au_opt_wbr_create *create;
+	} u;
+	struct {
+		substring_t args[MAX_OPT_ARGS];
+	} *a;
+
+	err = -ENOMEM;
+	a = kmalloc(sizeof(*a), GFP_NOFS);
+	if (unlikely(!a))
+		goto out;
+
+	root = sb->s_root;
+	err = 0;
+	bindex = 0;
+	opt = opts->opt;
+	opt_tail = opt + opts->max_opt - 1;
+	opt->type = Opt_tail;
+	while (!err && (opt_str = strsep(&str, ",")) && *opt_str) {
+		err = -EINVAL;
+		skipped = 0;
+		token = match_token(opt_str, options, a->args);
+		switch (token) {
+		case Opt_br:
+			err = 0;
+			while (!err && (opt_str = strsep(&a->args[0].from, ":"))
+			       && *opt_str) {
+				err = opt_add(opt, opt_str, opts->sb_flags,
+					      bindex++);
+				if (unlikely(!err && ++opt > opt_tail)) {
+					err = -E2BIG;
+					break;
+				}
+				opt->type = Opt_tail;
+				skipped = 1;
+			}
+			break;
+		case Opt_add:
+			if (unlikely(match_int(&a->args[0], &n))) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			bindex = n;
+			err = opt_add(opt, a->args[1].from, opts->sb_flags,
+				      bindex);
+			if (!err)
+				opt->type = token;
+			break;
+		case Opt_append:
+			err = opt_add(opt, a->args[0].from, opts->sb_flags,
+				      /*dummy bindex*/1);
+			if (!err)
+				opt->type = token;
+			break;
+		case Opt_prepend:
+			err = opt_add(opt, a->args[0].from, opts->sb_flags,
+				      /*bindex*/0);
+			if (!err)
+				opt->type = token;
+			break;
+		case Opt_del:
+			err = au_opts_parse_del(&opt->del, a->args);
+			if (!err)
+				opt->type = token;
+			break;
+#if 0 /* reserved for future use */
+		case Opt_idel:
+			del->pathname = "(indexed)";
+			if (unlikely(match_int(&args[0], &n))) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			err = au_opts_parse_idel(sb, n, &opt->del, a->args);
+			if (!err)
+				opt->type = token;
+			break;
+#endif
+		case Opt_mod:
+			err = au_opts_parse_mod(&opt->mod, a->args);
+			if (!err)
+				opt->type = token;
+			break;
+#ifdef IMOD /* reserved for future use */
+		case Opt_imod:
+			u.mod->path = "(indexed)";
+			if (unlikely(match_int(&a->args[0], &n))) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			err = au_opts_parse_imod(sb, n, &opt->mod, a->args);
+			if (!err)
+				opt->type = token;
+			break;
+#endif
+		case Opt_xino:
+			err = au_opts_parse_xino(sb, &opt->xino, a->args);
+			if (!err)
+				opt->type = token;
+			break;
+
+		case Opt_trunc_xino_path:
+			err = au_opts_parse_xino_itrunc_path
+				(sb, &opt->xino_itrunc, a->args);
+			if (!err)
+				opt->type = token;
+			break;
+
+		case Opt_itrunc_xino:
+			u.xino_itrunc = &opt->xino_itrunc;
+			if (unlikely(match_int(&a->args[0], &n))) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			u.xino_itrunc->bindex = n;
+			aufs_read_lock(root, AuLock_FLUSH);
+			if (n < 0 || au_sbbot(sb) < n) {
+				pr_err("out of bounds, %d\n", n);
+				aufs_read_unlock(root, !AuLock_IR);
+				break;
+			}
+			aufs_read_unlock(root, !AuLock_IR);
+			err = 0;
+			opt->type = token;
+			break;
+
+		case Opt_dirwh:
+			if (unlikely(match_int(&a->args[0], &opt->dirwh)))
+				break;
+			err = 0;
+			opt->type = token;
+			break;
+
+		case Opt_rdcache:
+			if (unlikely(match_int(&a->args[0], &n))) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			if (unlikely(n > AUFS_RDCACHE_MAX)) {
+				pr_err("rdcache must be smaller than %d\n",
+				       AUFS_RDCACHE_MAX);
+				break;
+			}
+			opt->rdcache = n;
+			err = 0;
+			opt->type = token;
+			break;
+		case Opt_rdblk:
+			if (unlikely(match_int(&a->args[0], &n)
+				     || n < 0
+				     || n > KMALLOC_MAX_SIZE)) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			if (unlikely(n && n < NAME_MAX)) {
+				pr_err("rdblk must be larger than %d\n",
+				       NAME_MAX);
+				break;
+			}
+			opt->rdblk = n;
+			err = 0;
+			opt->type = token;
+			break;
+		case Opt_rdhash:
+			if (unlikely(match_int(&a->args[0], &n)
+				     || n < 0
+				     || n * sizeof(struct hlist_head)
+				     > KMALLOC_MAX_SIZE)) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			opt->rdhash = n;
+			err = 0;
+			opt->type = token;
+			break;
+
+		case Opt_trunc_xino:
+		case Opt_notrunc_xino:
+		case Opt_noxino:
+		case Opt_trunc_xib:
+		case Opt_notrunc_xib:
+		case Opt_shwh:
+		case Opt_noshwh:
+		case Opt_dirperm1:
+		case Opt_nodirperm1:
+		case Opt_plink:
+		case Opt_noplink:
+		case Opt_list_plink:
+		case Opt_dio:
+		case Opt_nodio:
+		case Opt_diropq_a:
+		case Opt_diropq_w:
+		case Opt_warn_perm:
+		case Opt_nowarn_perm:
+		case Opt_verbose:
+		case Opt_noverbose:
+		case Opt_sum:
+		case Opt_nosum:
+		case Opt_wsum:
+		case Opt_rdblk_def:
+		case Opt_rdhash_def:
+		case Opt_dirren:
+		case Opt_nodirren:
+		case Opt_acl:
+		case Opt_noacl:
+			err = 0;
+			opt->type = token;
+			break;
+
+		case Opt_udba:
+			opt->udba = udba_val(a->args[0].from);
+			if (opt->udba >= 0) {
+				err = 0;
+				opt->type = token;
+			} else
+				pr_err("wrong value, %s\n", opt_str);
+			break;
+
+		case Opt_wbr_create:
+			u.create = &opt->wbr_create;
+			u.create->wbr_create
+				= au_wbr_create_val(a->args[0].from, u.create);
+			if (u.create->wbr_create >= 0) {
+				err = 0;
+				opt->type = token;
+			} else
+				pr_err("wrong value, %s\n", opt_str);
+			break;
+		case Opt_wbr_copyup:
+			opt->wbr_copyup = au_wbr_copyup_val(a->args[0].from);
+			if (opt->wbr_copyup >= 0) {
+				err = 0;
+				opt->type = token;
+			} else
+				pr_err("wrong value, %s\n", opt_str);
+			break;
+
+		case Opt_fhsm_sec:
+			if (unlikely(match_int(&a->args[0], &n)
+				     || n < 0)) {
+				pr_err("bad integer in %s\n", opt_str);
+				break;
+			}
+			if (sysaufs_brs) {
+				opt->fhsm_second = n;
+				opt->type = token;
+			} else
+				pr_warn("ignored %s\n", opt_str);
+			err = 0;
+			break;
+
+		case Opt_ignore:
+			pr_warn("ignored %s\n", opt_str);
+			fallthrough;
+		case Opt_ignore_silent:
+			skipped = 1;
+			err = 0;
+			break;
+		case Opt_err:
+			pr_err("unknown option %s\n", opt_str);
+			break;
+		}
+
+		if (!err && !skipped) {
+			if (unlikely(++opt > opt_tail)) {
+				err = -E2BIG;
+				opt--;
+				opt->type = Opt_tail;
+				break;
+			}
+			opt->type = Opt_tail;
+		}
+	}
+
+	au_kfree_rcu(a);
+	dump_opts(opts);
+	if (unlikely(err))
+		au_opts_free(opts);
+
+out:
+	return err;
+}
+
+static int au_opt_wbr_create(struct super_block *sb,
+			     struct au_opt_wbr_create *create)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+
+	SiMustWriteLock(sb);
+
+	err = 1; /* handled */
+	sbinfo = au_sbi(sb);
+	if (sbinfo->si_wbr_create_ops->fin) {
+		err = sbinfo->si_wbr_create_ops->fin(sb);
+		if (!err)
+			err = 1;
+	}
+
+	sbinfo->si_wbr_create = create->wbr_create;
+	sbinfo->si_wbr_create_ops = au_wbr_create_ops + create->wbr_create;
+	switch (create->wbr_create) {
+	case AuWbrCreate_MFSRRV:
+	case AuWbrCreate_MFSRR:
+	case AuWbrCreate_TDMFS:
+	case AuWbrCreate_TDMFSV:
+	case AuWbrCreate_PMFSRR:
+	case AuWbrCreate_PMFSRRV:
+		sbinfo->si_wbr_mfs.mfsrr_watermark = create->mfsrr_watermark;
+		fallthrough;
+	case AuWbrCreate_MFS:
+	case AuWbrCreate_MFSV:
+	case AuWbrCreate_PMFS:
+	case AuWbrCreate_PMFSV:
+		sbinfo->si_wbr_mfs.mfs_expire
+			= msecs_to_jiffies(create->mfs_second * MSEC_PER_SEC);
+		break;
+	}
+
+	if (sbinfo->si_wbr_create_ops->init)
+		sbinfo->si_wbr_create_ops->init(sb); /* ignore */
+
+	return err;
+}
+
+/*
+ * returns,
+ * plus: processed without an error
+ * zero: unprocessed
+ */
+static int au_opt_simple(struct super_block *sb, struct au_opt *opt,
+			 struct au_opts *opts)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+
+	SiMustWriteLock(sb);
+
+	err = 1; /* handled */
+	sbinfo = au_sbi(sb);
+	switch (opt->type) {
+	case Opt_udba:
+		sbinfo->si_mntflags &= ~AuOptMask_UDBA;
+		sbinfo->si_mntflags |= opt->udba;
+		opts->given_udba |= opt->udba;
+		break;
+
+	case Opt_plink:
+		au_opt_set(sbinfo->si_mntflags, PLINK);
+		break;
+	case Opt_noplink:
+		if (au_opt_test(sbinfo->si_mntflags, PLINK))
+			au_plink_put(sb, /*verbose*/1);
+		au_opt_clr(sbinfo->si_mntflags, PLINK);
+		break;
+	case Opt_list_plink:
+		if (au_opt_test(sbinfo->si_mntflags, PLINK))
+			au_plink_list(sb);
+		break;
+
+	case Opt_dio:
+		au_opt_set(sbinfo->si_mntflags, DIO);
+		au_fset_opts(opts->flags, REFRESH_DYAOP);
+		break;
+	case Opt_nodio:
+		au_opt_clr(sbinfo->si_mntflags, DIO);
+		au_fset_opts(opts->flags, REFRESH_DYAOP);
+		break;
+
+	case Opt_fhsm_sec:
+		au_fhsm_set(sbinfo, opt->fhsm_second);
+		break;
+
+	case Opt_diropq_a:
+		au_opt_set(sbinfo->si_mntflags, ALWAYS_DIROPQ);
+		break;
+	case Opt_diropq_w:
+		au_opt_clr(sbinfo->si_mntflags, ALWAYS_DIROPQ);
+		break;
+
+	case Opt_warn_perm:
+		au_opt_set(sbinfo->si_mntflags, WARN_PERM);
+		break;
+	case Opt_nowarn_perm:
+		au_opt_clr(sbinfo->si_mntflags, WARN_PERM);
+		break;
+
+	case Opt_verbose:
+		au_opt_set(sbinfo->si_mntflags, VERBOSE);
+		break;
+	case Opt_noverbose:
+		au_opt_clr(sbinfo->si_mntflags, VERBOSE);
+		break;
+
+	case Opt_sum:
+		au_opt_set(sbinfo->si_mntflags, SUM);
+		break;
+	case Opt_wsum:
+		au_opt_clr(sbinfo->si_mntflags, SUM);
+		au_opt_set(sbinfo->si_mntflags, SUM_W);
+		break;
+	case Opt_nosum:
+		au_opt_clr(sbinfo->si_mntflags, SUM);
+		au_opt_clr(sbinfo->si_mntflags, SUM_W);
+		break;
+
+	case Opt_wbr_create:
+		err = au_opt_wbr_create(sb, &opt->wbr_create);
+		break;
+	case Opt_wbr_copyup:
+		sbinfo->si_wbr_copyup = opt->wbr_copyup;
+		sbinfo->si_wbr_copyup_ops = au_wbr_copyup_ops + opt->wbr_copyup;
+		break;
+
+	case Opt_dirwh:
+		sbinfo->si_dirwh = opt->dirwh;
+		break;
+
+	case Opt_rdcache:
+		sbinfo->si_rdcache
+			= msecs_to_jiffies(opt->rdcache * MSEC_PER_SEC);
+		break;
+	case Opt_rdblk:
+		sbinfo->si_rdblk = opt->rdblk;
+		break;
+	case Opt_rdblk_def:
+		sbinfo->si_rdblk = AUFS_RDBLK_DEF;
+		break;
+	case Opt_rdhash:
+		sbinfo->si_rdhash = opt->rdhash;
+		break;
+	case Opt_rdhash_def:
+		sbinfo->si_rdhash = AUFS_RDHASH_DEF;
+		break;
+
+	case Opt_shwh:
+		au_opt_set(sbinfo->si_mntflags, SHWH);
+		break;
+	case Opt_noshwh:
+		au_opt_clr(sbinfo->si_mntflags, SHWH);
+		break;
+
+	case Opt_dirperm1:
+		au_opt_set(sbinfo->si_mntflags, DIRPERM1);
+		break;
+	case Opt_nodirperm1:
+		au_opt_clr(sbinfo->si_mntflags, DIRPERM1);
+		break;
+
+	case Opt_trunc_xino:
+		au_opt_set(sbinfo->si_mntflags, TRUNC_XINO);
+		break;
+	case Opt_notrunc_xino:
+		au_opt_clr(sbinfo->si_mntflags, TRUNC_XINO);
+		break;
+
+	case Opt_trunc_xino_path:
+	case Opt_itrunc_xino:
+		err = au_xino_trunc(sb, opt->xino_itrunc.bindex,
+				    /*idx_begin*/0);
+		if (!err)
+			err = 1;
+		break;
+
+	case Opt_trunc_xib:
+		au_fset_opts(opts->flags, TRUNC_XIB);
+		break;
+	case Opt_notrunc_xib:
+		au_fclr_opts(opts->flags, TRUNC_XIB);
+		break;
+
+	case Opt_dirren:
+		err = 1;
+		if (!au_opt_test(sbinfo->si_mntflags, DIRREN)) {
+			err = au_dr_opt_set(sb);
+			if (!err)
+				err = 1;
+		}
+		if (err == 1)
+			au_opt_set(sbinfo->si_mntflags, DIRREN);
+		break;
+	case Opt_nodirren:
+		err = 1;
+		if (au_opt_test(sbinfo->si_mntflags, DIRREN)) {
+			err = au_dr_opt_clr(sb, au_ftest_opts(opts->flags,
+							      DR_FLUSHED));
+			if (!err)
+				err = 1;
+		}
+		if (err == 1)
+			au_opt_clr(sbinfo->si_mntflags, DIRREN);
+		break;
+
+	case Opt_acl:
+		sb->s_flags |= SB_POSIXACL;
+		break;
+	case Opt_noacl:
+		sb->s_flags &= ~SB_POSIXACL;
+		break;
+
+	default:
+		err = 0;
+		break;
+	}
+
+	return err;
+}
+
+/*
+ * returns tri-state.
+ * plus: processed without an error
+ * zero: unprocessed
+ * minus: error
+ */
+static int au_opt_br(struct super_block *sb, struct au_opt *opt,
+		     struct au_opts *opts)
+{
+	int err, do_refresh;
+
+	err = 0;
+	switch (opt->type) {
+	case Opt_append:
+		opt->add.bindex = au_sbbot(sb) + 1;
+		if (opt->add.bindex < 0)
+			opt->add.bindex = 0;
+		goto add;
+		/* Always goto add, not fallthrough */
+	case Opt_prepend:
+		opt->add.bindex = 0;
+		fallthrough;
+	add: /* indented label */
+	case Opt_add:
+		err = au_br_add(sb, &opt->add,
+				au_ftest_opts(opts->flags, REMOUNT));
+		if (!err) {
+			err = 1;
+			au_fset_opts(opts->flags, REFRESH);
+		}
+		break;
+
+	case Opt_del:
+	case Opt_idel:
+		err = au_br_del(sb, &opt->del,
+				au_ftest_opts(opts->flags, REMOUNT));
+		if (!err) {
+			err = 1;
+			au_fset_opts(opts->flags, TRUNC_XIB);
+			au_fset_opts(opts->flags, REFRESH);
+		}
+		break;
+
+	case Opt_mod:
+	case Opt_imod:
+		err = au_br_mod(sb, &opt->mod,
+				au_ftest_opts(opts->flags, REMOUNT),
+				&do_refresh);
+		if (!err) {
+			err = 1;
+			if (do_refresh)
+				au_fset_opts(opts->flags, REFRESH);
+		}
+		break;
+	}
+	return err;
+}
+
+static int au_opt_xino(struct super_block *sb, struct au_opt *opt,
+		       struct au_opt_xino **opt_xino,
+		       struct au_opts *opts)
+{
+	int err;
+
+	err = 0;
+	switch (opt->type) {
+	case Opt_xino:
+		err = au_xino_set(sb, &opt->xino,
+				  !!au_ftest_opts(opts->flags, REMOUNT));
+		if (unlikely(err))
+			break;
+
+		*opt_xino = &opt->xino;
+		break;
+
+	case Opt_noxino:
+		au_xino_clr(sb);
+		*opt_xino = (void *)-1;
+		break;
+	}
+
+	return err;
+}
+
+int au_opts_verify(struct super_block *sb, unsigned long sb_flags,
+		   unsigned int pending)
+{
+	int err, fhsm;
+	aufs_bindex_t bindex, bbot;
+	unsigned char do_plink, skip, do_free, can_no_dreval;
+	struct au_branch *br;
+	struct au_wbr *wbr;
+	struct dentry *root, *dentry;
+	struct inode *dir, *h_dir;
+	struct au_sbinfo *sbinfo;
+	struct au_hinode *hdir;
+
+	SiMustAnyLock(sb);
+
+	sbinfo = au_sbi(sb);
+	AuDebugOn(!(sbinfo->si_mntflags & AuOptMask_UDBA));
+
+	if (!(sb_flags & SB_RDONLY)) {
+		if (unlikely(!au_br_writable(au_sbr_perm(sb, 0))))
+			pr_warn("first branch should be rw\n");
+		if (unlikely(au_opt_test(sbinfo->si_mntflags, SHWH)))
+			pr_warn_once("shwh should be used with ro\n");
+	}
+
+	if (au_opt_test((sbinfo->si_mntflags | pending), UDBA_HNOTIFY)
+	    && !au_opt_test(sbinfo->si_mntflags, XINO))
+		pr_warn_once("udba=*notify requires xino\n");
+
+	if (au_opt_test(sbinfo->si_mntflags, DIRPERM1))
+		pr_warn_once("dirperm1 breaks the protection"
+			     " by the permission bits on the lower branch\n");
+
+	err = 0;
+	fhsm = 0;
+	root = sb->s_root;
+	dir = d_inode(root);
+	do_plink = !!au_opt_test(sbinfo->si_mntflags, PLINK);
+	can_no_dreval = !!au_opt_test((sbinfo->si_mntflags | pending),
+				      UDBA_NONE);
+	bbot = au_sbbot(sb);
+	for (bindex = 0; !err && bindex <= bbot; bindex++) {
+		skip = 0;
+		h_dir = au_h_iptr(dir, bindex);
+		br = au_sbr(sb, bindex);
+
+		if ((br->br_perm & AuBrAttr_ICEX)
+		    && !h_dir->i_op->listxattr)
+			br->br_perm &= ~AuBrAttr_ICEX;
+#if 0 /* untested */
+		if ((br->br_perm & AuBrAttr_ICEX_SEC)
+		    && (au_br_sb(br)->s_flags & SB_NOSEC))
+			br->br_perm &= ~AuBrAttr_ICEX_SEC;
+#endif
+
+		do_free = 0;
+		wbr = br->br_wbr;
+		if (wbr)
+			wbr_wh_read_lock(wbr);
+
+		if (!au_br_writable(br->br_perm)) {
+			do_free = !!wbr;
+			skip = (!wbr
+				|| (!wbr->wbr_whbase
+				    && !wbr->wbr_plink
+				    && !wbr->wbr_orph));
+		} else if (!au_br_wh_linkable(br->br_perm)) {
+			/* skip = (!br->br_whbase && !br->br_orph); */
+			skip = (!wbr || !wbr->wbr_whbase);
+			if (skip && wbr) {
+				if (do_plink)
+					skip = !!wbr->wbr_plink;
+				else
+					skip = !wbr->wbr_plink;
+			}
+		} else {
+			/* skip = (br->br_whbase && br->br_ohph); */
+			skip = (wbr && wbr->wbr_whbase);
+			if (skip) {
+				if (do_plink)
+					skip = !!wbr->wbr_plink;
+				else
+					skip = !wbr->wbr_plink;
+			}
+		}
+		if (wbr)
+			wbr_wh_read_unlock(wbr);
+
+		if (can_no_dreval) {
+			dentry = br->br_path.dentry;
+			spin_lock(&dentry->d_lock);
+			if (dentry->d_flags &
+			    (DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE))
+				can_no_dreval = 0;
+			spin_unlock(&dentry->d_lock);
+		}
+
+		if (au_br_fhsm(br->br_perm)) {
+			fhsm++;
+			AuDebugOn(!br->br_fhsm);
+		}
+
+		if (skip)
+			continue;
+
+		hdir = au_hi(dir, bindex);
+		au_hn_inode_lock_nested(hdir, AuLsc_I_PARENT);
+		if (wbr)
+			wbr_wh_write_lock(wbr);
+		err = au_wh_init(br, sb);
+		if (wbr)
+			wbr_wh_write_unlock(wbr);
+		au_hn_inode_unlock(hdir);
+
+		if (!err && do_free) {
+			au_kfree_rcu(wbr);
+			br->br_wbr = NULL;
+		}
+	}
+
+	if (can_no_dreval)
+		au_fset_si(sbinfo, NO_DREVAL);
+	else
+		au_fclr_si(sbinfo, NO_DREVAL);
+
+	if (fhsm >= 2) {
+		au_fset_si(sbinfo, FHSM);
+		for (bindex = bbot; bindex >= 0; bindex--) {
+			br = au_sbr(sb, bindex);
+			if (au_br_fhsm(br->br_perm)) {
+				au_fhsm_set_bottom(sb, bindex);
+				break;
+			}
+		}
+	} else {
+		au_fclr_si(sbinfo, FHSM);
+		au_fhsm_set_bottom(sb, -1);
+	}
+
+	return err;
+}
+
+int au_opts_mount(struct super_block *sb, struct au_opts *opts)
+{
+	int err;
+	unsigned int tmp;
+	aufs_bindex_t bindex, bbot;
+	struct au_opt *opt;
+	struct au_opt_xino *opt_xino, xino;
+	struct au_sbinfo *sbinfo;
+	struct au_branch *br;
+	struct inode *dir;
+
+	SiMustWriteLock(sb);
+
+	err = 0;
+	opt_xino = NULL;
+	opt = opts->opt;
+	while (err >= 0 && opt->type != Opt_tail)
+		err = au_opt_simple(sb, opt++, opts);
+	if (err > 0)
+		err = 0;
+	else if (unlikely(err < 0))
+		goto out;
+
+	/* disable xino and udba temporary */
+	sbinfo = au_sbi(sb);
+	tmp = sbinfo->si_mntflags;
+	au_opt_clr(sbinfo->si_mntflags, XINO);
+	au_opt_set_udba(sbinfo->si_mntflags, UDBA_REVAL);
+
+	opt = opts->opt;
+	while (err >= 0 && opt->type != Opt_tail)
+		err = au_opt_br(sb, opt++, opts);
+	if (err > 0)
+		err = 0;
+	else if (unlikely(err < 0))
+		goto out;
+
+	bbot = au_sbbot(sb);
+	if (unlikely(bbot < 0)) {
+		err = -EINVAL;
+		pr_err("no branches\n");
+		goto out;
+	}
+
+	if (au_opt_test(tmp, XINO))
+		au_opt_set(sbinfo->si_mntflags, XINO);
+	opt = opts->opt;
+	while (!err && opt->type != Opt_tail)
+		err = au_opt_xino(sb, opt++, &opt_xino, opts);
+	if (unlikely(err))
+		goto out;
+
+	err = au_opts_verify(sb, sb->s_flags, tmp);
+	if (unlikely(err))
+		goto out;
+
+	/* restore xino */
+	if (au_opt_test(tmp, XINO) && !opt_xino) {
+		xino.file = au_xino_def(sb);
+		err = PTR_ERR(xino.file);
+		if (IS_ERR(xino.file))
+			goto out;
+
+		err = au_xino_set(sb, &xino, /*remount*/0);
+		fput(xino.file);
+		if (unlikely(err))
+			goto out;
+	}
+
+	/* restore udba */
+	tmp &= AuOptMask_UDBA;
+	sbinfo->si_mntflags &= ~AuOptMask_UDBA;
+	sbinfo->si_mntflags |= tmp;
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		err = au_hnotify_reset_br(tmp, br, br->br_perm);
+		if (unlikely(err))
+			AuIOErr("hnotify failed on br %d, %d, ignored\n",
+				bindex, err);
+		/* go on even if err */
+	}
+	if (au_opt_test(tmp, UDBA_HNOTIFY)) {
+		dir = d_inode(sb->s_root);
+		au_hn_reset(dir, au_hi_flags(dir, /*isdir*/1) & ~AuHi_XINO);
+	}
+
+out:
+	return err;
+}
+
+int au_opts_remount(struct super_block *sb, struct au_opts *opts)
+{
+	int err, rerr;
+	unsigned char no_dreval;
+	struct inode *dir;
+	struct au_opt_xino *opt_xino;
+	struct au_opt *opt;
+	struct au_sbinfo *sbinfo;
+
+	SiMustWriteLock(sb);
+
+	err = au_dr_opt_flush(sb);
+	if (unlikely(err))
+		goto out;
+	au_fset_opts(opts->flags, DR_FLUSHED);
+
+	dir = d_inode(sb->s_root);
+	sbinfo = au_sbi(sb);
+	opt_xino = NULL;
+	opt = opts->opt;
+	while (err >= 0 && opt->type != Opt_tail) {
+		err = au_opt_simple(sb, opt, opts);
+		if (!err)
+			err = au_opt_br(sb, opt, opts);
+		if (!err)
+			err = au_opt_xino(sb, opt, &opt_xino, opts);
+		opt++;
+	}
+	if (err > 0)
+		err = 0;
+	AuTraceErr(err);
+	/* go on even err */
+
+	no_dreval = !!au_ftest_si(sbinfo, NO_DREVAL);
+	rerr = au_opts_verify(sb, opts->sb_flags, /*pending*/0);
+	if (unlikely(rerr && !err))
+		err = rerr;
+
+	if (no_dreval != !!au_ftest_si(sbinfo, NO_DREVAL))
+		au_fset_opts(opts->flags, REFRESH_IDOP);
+
+	if (au_ftest_opts(opts->flags, TRUNC_XIB)) {
+		rerr = au_xib_trunc(sb);
+		if (unlikely(rerr && !err))
+			err = rerr;
+	}
+
+	/* will be handled by the caller */
+	if (!au_ftest_opts(opts->flags, REFRESH)
+	    && (opts->given_udba
+		|| au_opt_test(sbinfo->si_mntflags, XINO)
+		|| au_ftest_opts(opts->flags, REFRESH_IDOP)
+		    ))
+		au_fset_opts(opts->flags, REFRESH);
+
+	AuDbg("status 0x%x\n", opts->flags);
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+unsigned int au_opt_udba(struct super_block *sb)
+{
+	return au_mntflags(sb) & AuOptMask_UDBA;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/opts.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/opts.h
@@ -0,0 +1,225 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * mount options/flags
+ */
+
+#ifndef __AUFS_OPTS_H__
+#define __AUFS_OPTS_H__
+
+#ifdef __KERNEL__
+
+#include <linux/path.h>
+
+struct file;
+
+/* ---------------------------------------------------------------------- */
+
+/* mount flags */
+#define AuOpt_XINO		1		/* external inode number bitmap
+						   and translation table */
+#define AuOpt_TRUNC_XINO	(1 << 1)	/* truncate xino files */
+#define AuOpt_UDBA_NONE		(1 << 2)	/* users direct branch access */
+#define AuOpt_UDBA_REVAL	(1 << 3)
+#define AuOpt_UDBA_HNOTIFY	(1 << 4)
+#define AuOpt_SHWH		(1 << 5)	/* show whiteout */
+#define AuOpt_PLINK		(1 << 6)	/* pseudo-link */
+#define AuOpt_DIRPERM1		(1 << 7)	/* ignore the lower dir's perm
+						   bits */
+#define AuOpt_ALWAYS_DIROPQ	(1 << 9)	/* policy to creating diropq */
+#define AuOpt_SUM		(1 << 10)	/* summation for statfs(2) */
+#define AuOpt_SUM_W		(1 << 11)	/* unimplemented */
+#define AuOpt_WARN_PERM		(1 << 12)	/* warn when add-branch */
+#define AuOpt_VERBOSE		(1 << 13)	/* print the cause of error */
+#define AuOpt_DIO		(1 << 14)	/* direct io */
+#define AuOpt_DIRREN		(1 << 15)	/* directory rename */
+
+#ifndef CONFIG_AUFS_HNOTIFY
+#undef AuOpt_UDBA_HNOTIFY
+#define AuOpt_UDBA_HNOTIFY	0
+#endif
+#ifndef CONFIG_AUFS_DIRREN
+#undef AuOpt_DIRREN
+#define AuOpt_DIRREN		0
+#endif
+#ifndef CONFIG_AUFS_SHWH
+#undef AuOpt_SHWH
+#define AuOpt_SHWH		0
+#endif
+
+#define AuOpt_Def	(AuOpt_XINO \
+			 | AuOpt_UDBA_REVAL \
+			 | AuOpt_PLINK \
+			 /* | AuOpt_DIRPERM1 */ \
+			 | AuOpt_WARN_PERM)
+#define AuOptMask_UDBA	(AuOpt_UDBA_NONE \
+			 | AuOpt_UDBA_REVAL \
+			 | AuOpt_UDBA_HNOTIFY)
+
+#define au_opt_test(flags, name)	(flags & AuOpt_##name)
+#define au_opt_set(flags, name) do { \
+	BUILD_BUG_ON(AuOpt_##name & AuOptMask_UDBA); \
+	((flags) |= AuOpt_##name); \
+} while (0)
+#define au_opt_set_udba(flags, name) do { \
+	(flags) &= ~AuOptMask_UDBA; \
+	((flags) |= AuOpt_##name); \
+} while (0)
+#define au_opt_clr(flags, name) do { \
+	((flags) &= ~AuOpt_##name); \
+} while (0)
+
+static inline unsigned int au_opts_plink(unsigned int mntflags)
+{
+#ifdef CONFIG_PROC_FS
+	return mntflags;
+#else
+	return mntflags & ~AuOpt_PLINK;
+#endif
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* policies to select one among multiple writable branches */
+enum {
+	AuWbrCreate_TDP,	/* top down parent */
+	AuWbrCreate_RR,		/* round robin */
+	AuWbrCreate_MFS,	/* most free space */
+	AuWbrCreate_MFSV,	/* mfs with seconds */
+	AuWbrCreate_MFSRR,	/* mfs then rr */
+	AuWbrCreate_MFSRRV,	/* mfs then rr with seconds */
+	AuWbrCreate_TDMFS,	/* top down regardless parent and mfs */
+	AuWbrCreate_TDMFSV,	/* top down regardless parent and mfs */
+	AuWbrCreate_PMFS,	/* parent and mfs */
+	AuWbrCreate_PMFSV,	/* parent and mfs with seconds */
+	AuWbrCreate_PMFSRR,	/* parent, mfs and round-robin */
+	AuWbrCreate_PMFSRRV,	/* plus seconds */
+
+	AuWbrCreate_Def = AuWbrCreate_TDP
+};
+
+enum {
+	AuWbrCopyup_TDP,	/* top down parent */
+	AuWbrCopyup_BUP,	/* bottom up parent */
+	AuWbrCopyup_BU,		/* bottom up */
+
+	AuWbrCopyup_Def = AuWbrCopyup_TDP
+};
+
+/* ---------------------------------------------------------------------- */
+
+struct au_opt_add {
+	aufs_bindex_t	bindex;
+	char		*pathname;
+	int		perm;
+	struct path	path;
+};
+
+struct au_opt_del {
+	char		*pathname;
+	struct path	h_path;
+};
+
+struct au_opt_mod {
+	char		*path;
+	int		perm;
+	struct dentry	*h_root;
+};
+
+struct au_opt_xino {
+	char		*path;
+	struct file	*file;
+};
+
+struct au_opt_xino_itrunc {
+	aufs_bindex_t	bindex;
+};
+
+struct au_opt_wbr_create {
+	int			wbr_create;
+	int			mfs_second;
+	unsigned long long	mfsrr_watermark;
+};
+
+struct au_opt {
+	int type;
+	union {
+		struct au_opt_xino	xino;
+		struct au_opt_xino_itrunc xino_itrunc;
+		struct au_opt_add	add;
+		struct au_opt_del	del;
+		struct au_opt_mod	mod;
+		int			dirwh;
+		int			rdcache;
+		unsigned int		rdblk;
+		unsigned int		rdhash;
+		int			udba;
+		struct au_opt_wbr_create wbr_create;
+		int			wbr_copyup;
+		unsigned int		fhsm_second;
+	};
+};
+
+/* opts flags */
+#define AuOpts_REMOUNT		1
+#define AuOpts_REFRESH		(1 << 1)
+#define AuOpts_TRUNC_XIB	(1 << 2)
+#define AuOpts_REFRESH_DYAOP	(1 << 3)
+#define AuOpts_REFRESH_IDOP	(1 << 4)
+#define AuOpts_DR_FLUSHED	(1 << 5)
+#define au_ftest_opts(flags, name)	((flags) & AuOpts_##name)
+#define au_fset_opts(flags, name) \
+	do { (flags) |= AuOpts_##name; } while (0)
+#define au_fclr_opts(flags, name) \
+	do { (flags) &= ~AuOpts_##name; } while (0)
+
+#ifndef CONFIG_AUFS_DIRREN
+#undef AuOpts_DR_FLUSHED
+#define AuOpts_DR_FLUSHED	0
+#endif
+
+struct au_opts {
+	struct au_opt	*opt;
+	int		max_opt;
+
+	unsigned int	given_udba;
+	unsigned int	flags;
+	unsigned long	sb_flags;
+};
+
+/* ---------------------------------------------------------------------- */
+
+/* opts.c */
+void au_optstr_br_perm(au_br_perm_str_t *str, int perm);
+const char *au_optstr_udba(int udba);
+const char *au_optstr_wbr_copyup(int wbr_copyup);
+const char *au_optstr_wbr_create(int wbr_create);
+
+void au_opts_free(struct au_opts *opts);
+struct super_block;
+int au_opts_parse(struct super_block *sb, char *str, struct au_opts *opts);
+int au_opts_verify(struct super_block *sb, unsigned long sb_flags,
+		   unsigned int pending);
+int au_opts_mount(struct super_block *sb, struct au_opts *opts);
+int au_opts_remount(struct super_block *sb, struct au_opts *opts);
+
+unsigned int au_opt_udba(struct super_block *sb);
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_OPTS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/plink.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/plink.c
@@ -0,0 +1,516 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * pseudo-link
+ */
+
+#include "aufs.h"
+
+/*
+ * the pseudo-link maintenance mode.
+ * during a user process maintains the pseudo-links,
+ * prohibit adding a new plink and branch manipulation.
+ *
+ * Flags
+ * NOPLM:
+ *	For entry functions which will handle plink, and i_mutex is already held
+ *	in VFS.
+ *	They cannot wait and should return an error at once.
+ *	Callers has to check the error.
+ * NOPLMW:
+ *	For entry functions which will handle plink, but i_mutex is not held
+ *	in VFS.
+ *	They can wait the plink maintenance mode to finish.
+ *
+ * They behave like F_SETLK and F_SETLKW.
+ * If the caller never handle plink, then both flags are unnecessary.
+ */
+
+int au_plink_maint(struct super_block *sb, int flags)
+{
+	int err;
+	pid_t pid, ppid;
+	struct task_struct *parent, *prev;
+	struct au_sbinfo *sbi;
+
+	SiMustAnyLock(sb);
+
+	err = 0;
+	if (!au_opt_test(au_mntflags(sb), PLINK))
+		goto out;
+
+	sbi = au_sbi(sb);
+	pid = sbi->si_plink_maint_pid;
+	if (!pid || pid == current->pid)
+		goto out;
+
+	/* todo: it highly depends upon /sbin/mount.aufs */
+	prev = NULL;
+	parent = current;
+	ppid = 0;
+	rcu_read_lock();
+	while (1) {
+		parent = rcu_dereference(parent->real_parent);
+		if (parent == prev)
+			break;
+		ppid = task_pid_vnr(parent);
+		if (pid == ppid) {
+			rcu_read_unlock();
+			goto out;
+		}
+		prev = parent;
+	}
+	rcu_read_unlock();
+
+	if (au_ftest_lock(flags, NOPLMW)) {
+		/* if there is no i_mutex lock in VFS, we don't need to wait */
+		/* AuDebugOn(!lockdep_depth(current)); */
+		while (sbi->si_plink_maint_pid) {
+			si_read_unlock(sb);
+			/* gave up wake_up_bit() */
+			wait_event(sbi->si_plink_wq, !sbi->si_plink_maint_pid);
+
+			if (au_ftest_lock(flags, FLUSH))
+				au_nwt_flush(&sbi->si_nowait);
+			si_noflush_read_lock(sb);
+		}
+	} else if (au_ftest_lock(flags, NOPLM)) {
+		AuDbg("ppid %d, pid %d\n", ppid, pid);
+		err = -EAGAIN;
+	}
+
+out:
+	return err;
+}
+
+void au_plink_maint_leave(struct au_sbinfo *sbinfo)
+{
+	spin_lock(&sbinfo->si_plink_maint_lock);
+	sbinfo->si_plink_maint_pid = 0;
+	spin_unlock(&sbinfo->si_plink_maint_lock);
+	wake_up_all(&sbinfo->si_plink_wq);
+}
+
+int au_plink_maint_enter(struct super_block *sb)
+{
+	int err;
+	struct au_sbinfo *sbinfo;
+
+	err = 0;
+	sbinfo = au_sbi(sb);
+	/* make sure i am the only one in this fs */
+	si_write_lock(sb, AuLock_FLUSH);
+	if (au_opt_test(au_mntflags(sb), PLINK)) {
+		spin_lock(&sbinfo->si_plink_maint_lock);
+		if (!sbinfo->si_plink_maint_pid)
+			sbinfo->si_plink_maint_pid = current->pid;
+		else
+			err = -EBUSY;
+		spin_unlock(&sbinfo->si_plink_maint_lock);
+	}
+	si_write_unlock(sb);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_DEBUG
+void au_plink_list(struct super_block *sb)
+{
+	int i;
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	struct au_icntnr *icntnr;
+
+	SiMustAnyLock(sb);
+
+	sbinfo = au_sbi(sb);
+	AuDebugOn(!au_opt_test(au_mntflags(sb), PLINK));
+	AuDebugOn(au_plink_maint(sb, AuLock_NOPLM));
+
+	for (i = 0; i < AuPlink_NHASH; i++) {
+		hbl = sbinfo->si_plink + i;
+		hlist_bl_lock(hbl);
+		hlist_bl_for_each_entry(icntnr, pos, hbl, plink)
+			AuDbg("%lu\n", icntnr->vfs_inode.i_ino);
+		hlist_bl_unlock(hbl);
+	}
+}
+#endif
+
+/* is the inode pseudo-linked? */
+int au_plink_test(struct inode *inode)
+{
+	int found, i;
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	struct au_icntnr *icntnr;
+
+	sbinfo = au_sbi(inode->i_sb);
+	AuRwMustAnyLock(&sbinfo->si_rwsem);
+	AuDebugOn(!au_opt_test(au_mntflags(inode->i_sb), PLINK));
+	AuDebugOn(au_plink_maint(inode->i_sb, AuLock_NOPLM));
+
+	found = 0;
+	i = au_plink_hash(inode->i_ino);
+	hbl =  sbinfo->si_plink + i;
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(icntnr, pos, hbl, plink)
+		if (&icntnr->vfs_inode == inode) {
+			found = 1;
+			break;
+		}
+	hlist_bl_unlock(hbl);
+	return found;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * generate a name for plink.
+ * the file will be stored under AUFS_WH_PLINKDIR.
+ */
+/* 20 is max digits length of ulong 64 */
+#define PLINK_NAME_LEN	((20 + 1) * 2)
+
+static int plink_name(char *name, int len, struct inode *inode,
+		      aufs_bindex_t bindex)
+{
+	int rlen;
+	struct inode *h_inode;
+
+	h_inode = au_h_iptr(inode, bindex);
+	rlen = snprintf(name, len, "%lu.%lu", inode->i_ino, h_inode->i_ino);
+	return rlen;
+}
+
+struct au_do_plink_lkup_args {
+	struct dentry **errp;
+	struct qstr *tgtname;
+	struct path *h_ppath;
+};
+
+static struct dentry *au_do_plink_lkup(struct qstr *tgtname,
+				       struct path *h_ppath)
+{
+	struct dentry *h_dentry;
+	struct inode *h_inode;
+
+	h_inode = d_inode(h_ppath->dentry);
+	inode_lock_shared_nested(h_inode, AuLsc_I_CHILD2);
+	h_dentry = vfsub_lkup_one(tgtname, h_ppath);
+	inode_unlock_shared(h_inode);
+
+	return h_dentry;
+}
+
+static void au_call_do_plink_lkup(void *args)
+{
+	struct au_do_plink_lkup_args *a = args;
+	*a->errp = au_do_plink_lkup(a->tgtname, a->h_ppath);
+}
+
+/* lookup the plink-ed @inode under the branch at @bindex */
+struct dentry *au_plink_lkup(struct inode *inode, aufs_bindex_t bindex)
+{
+	struct dentry *h_dentry;
+	struct au_branch *br;
+	struct path h_ppath;
+	int wkq_err;
+	char a[PLINK_NAME_LEN];
+	struct qstr tgtname = QSTR_INIT(a, 0);
+
+	AuDebugOn(au_plink_maint(inode->i_sb, AuLock_NOPLM));
+
+	br = au_sbr(inode->i_sb, bindex);
+	h_ppath.dentry = br->br_wbr->wbr_plink;
+	h_ppath.mnt = au_br_mnt(br);
+	tgtname.len = plink_name(a, sizeof(a), inode, bindex);
+
+	if (!uid_eq(current_fsuid(), GLOBAL_ROOT_UID)) {
+		struct au_do_plink_lkup_args args = {
+			.errp		= &h_dentry,
+			.tgtname	= &tgtname,
+			.h_ppath	= &h_ppath
+		};
+
+		wkq_err = au_wkq_wait(au_call_do_plink_lkup, &args);
+		if (unlikely(wkq_err))
+			h_dentry = ERR_PTR(wkq_err);
+	} else
+		h_dentry = au_do_plink_lkup(&tgtname, &h_ppath);
+
+	return h_dentry;
+}
+
+/* create a pseudo-link */
+static int do_whplink(struct qstr *tgt, struct path *h_ppath,
+		      struct dentry *h_dentry)
+{
+	int err;
+	struct path h_path;
+	struct inode *h_dir, *delegated;
+
+	h_dir = d_inode(h_ppath->dentry);
+	inode_lock_nested(h_dir, AuLsc_I_CHILD2);
+	h_path.mnt = h_ppath->mnt;
+again:
+	h_path.dentry = vfsub_lkup_one(tgt, h_ppath);
+	err = PTR_ERR(h_path.dentry);
+	if (IS_ERR(h_path.dentry))
+		goto out;
+
+	err = 0;
+	/* wh.plink dir is not monitored */
+	/* todo: is it really safe? */
+	if (d_is_positive(h_path.dentry)
+	    && d_inode(h_path.dentry) != d_inode(h_dentry)) {
+		delegated = NULL;
+		err = vfsub_unlink(h_dir, &h_path, &delegated, /*force*/0);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal unlink\n");
+			iput(delegated);
+		}
+		dput(h_path.dentry);
+		h_path.dentry = NULL;
+		if (!err)
+			goto again;
+	}
+	if (!err && d_is_negative(h_path.dentry)) {
+		delegated = NULL;
+		err = vfsub_link(h_dentry, h_dir, &h_path, &delegated);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal link\n");
+			iput(delegated);
+		}
+	}
+	dput(h_path.dentry);
+
+out:
+	inode_unlock(h_dir);
+	return err;
+}
+
+struct do_whplink_args {
+	int *errp;
+	struct qstr *tgt;
+	struct path *h_ppath;
+	struct dentry *h_dentry;
+};
+
+static void call_do_whplink(void *args)
+{
+	struct do_whplink_args *a = args;
+	*a->errp = do_whplink(a->tgt, a->h_ppath, a->h_dentry);
+}
+
+static int whplink(struct dentry *h_dentry, struct inode *inode,
+		   aufs_bindex_t bindex)
+{
+	int err, wkq_err;
+	struct au_branch *br;
+	struct au_wbr *wbr;
+	struct path h_ppath;
+	char a[PLINK_NAME_LEN];
+	struct qstr tgtname = QSTR_INIT(a, 0);
+
+	br = au_sbr(inode->i_sb, bindex);
+	wbr = br->br_wbr;
+	h_ppath.dentry = wbr->wbr_plink;
+	h_ppath.mnt = au_br_mnt(br);
+	tgtname.len = plink_name(a, sizeof(a), inode, bindex);
+
+	/* always superio. */
+	if (!uid_eq(current_fsuid(), GLOBAL_ROOT_UID)) {
+		struct do_whplink_args args = {
+			.errp		= &err,
+			.tgt		= &tgtname,
+			.h_ppath	= &h_ppath,
+			.h_dentry	= h_dentry
+		};
+		wkq_err = au_wkq_wait(call_do_whplink, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	} else
+		err = do_whplink(&tgtname, &h_ppath, h_dentry);
+
+	return err;
+}
+
+/*
+ * create a new pseudo-link for @h_dentry on @bindex.
+ * the linked inode is held in aufs @inode.
+ */
+void au_plink_append(struct inode *inode, aufs_bindex_t bindex,
+		     struct dentry *h_dentry)
+{
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	struct au_icntnr *icntnr;
+	int found, err, cnt, i;
+
+	sb = inode->i_sb;
+	sbinfo = au_sbi(sb);
+	AuDebugOn(!au_opt_test(au_mntflags(sb), PLINK));
+	AuDebugOn(au_plink_maint(sb, AuLock_NOPLM));
+
+	found = au_plink_test(inode);
+	if (found)
+		return;
+
+	i = au_plink_hash(inode->i_ino);
+	hbl = sbinfo->si_plink + i;
+	au_igrab(inode);
+
+	hlist_bl_lock(hbl);
+	hlist_bl_for_each_entry(icntnr, pos, hbl, plink) {
+		if (&icntnr->vfs_inode == inode) {
+			found = 1;
+			break;
+		}
+	}
+	if (!found) {
+		icntnr = container_of(inode, struct au_icntnr, vfs_inode);
+		hlist_bl_add_head(&icntnr->plink, hbl);
+	}
+	hlist_bl_unlock(hbl);
+	if (!found) {
+		cnt = au_hbl_count(hbl);
+#define msg "unexpectedly unbalanced or too many pseudo-links"
+		if (cnt > AUFS_PLINK_WARN)
+			AuWarn1(msg ", %d\n", cnt);
+#undef msg
+		err = whplink(h_dentry, inode, bindex);
+		if (unlikely(err)) {
+			pr_warn("err %d, damaged pseudo link.\n", err);
+			au_hbl_del(&icntnr->plink, hbl);
+			iput(&icntnr->vfs_inode);
+		}
+	} else
+		iput(&icntnr->vfs_inode);
+}
+
+/* free all plinks */
+void au_plink_put(struct super_block *sb, int verbose)
+{
+	int i, warned;
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos, *tmp;
+	struct au_icntnr *icntnr;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	AuDebugOn(!au_opt_test(au_mntflags(sb), PLINK));
+	AuDebugOn(au_plink_maint(sb, AuLock_NOPLM));
+
+	/* no spin_lock since sbinfo is write-locked */
+	warned = 0;
+	for (i = 0; i < AuPlink_NHASH; i++) {
+		hbl = sbinfo->si_plink + i;
+		if (!warned && verbose && !hlist_bl_empty(hbl)) {
+			pr_warn("pseudo-link is not flushed");
+			warned = 1;
+		}
+		hlist_bl_for_each_entry_safe(icntnr, pos, tmp, hbl, plink)
+			iput(&icntnr->vfs_inode);
+		INIT_HLIST_BL_HEAD(hbl);
+	}
+}
+
+void au_plink_clean(struct super_block *sb, int verbose)
+{
+	struct dentry *root;
+
+	root = sb->s_root;
+	aufs_write_lock(root);
+	if (au_opt_test(au_mntflags(sb), PLINK))
+		au_plink_put(sb, verbose);
+	aufs_write_unlock(root);
+}
+
+static int au_plink_do_half_refresh(struct inode *inode, aufs_bindex_t br_id)
+{
+	int do_put;
+	aufs_bindex_t btop, bbot, bindex;
+
+	do_put = 0;
+	btop = au_ibtop(inode);
+	bbot = au_ibbot(inode);
+	if (btop >= 0) {
+		for (bindex = btop; bindex <= bbot; bindex++) {
+			if (!au_h_iptr(inode, bindex)
+			    || au_ii_br_id(inode, bindex) != br_id)
+				continue;
+			au_set_h_iptr(inode, bindex, NULL, 0);
+			do_put = 1;
+			break;
+		}
+		if (do_put)
+			for (bindex = btop; bindex <= bbot; bindex++)
+				if (au_h_iptr(inode, bindex)) {
+					do_put = 0;
+					break;
+				}
+	} else
+		do_put = 1;
+
+	return do_put;
+}
+
+/* free the plinks on a branch specified by @br_id */
+void au_plink_half_refresh(struct super_block *sb, aufs_bindex_t br_id)
+{
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos, *tmp;
+	struct au_icntnr *icntnr;
+	struct inode *inode;
+	int i, do_put;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	AuDebugOn(!au_opt_test(au_mntflags(sb), PLINK));
+	AuDebugOn(au_plink_maint(sb, AuLock_NOPLM));
+
+	/* no bit_lock since sbinfo is write-locked */
+	for (i = 0; i < AuPlink_NHASH; i++) {
+		hbl = sbinfo->si_plink + i;
+		hlist_bl_for_each_entry_safe(icntnr, pos, tmp, hbl, plink) {
+			inode = au_igrab(&icntnr->vfs_inode);
+			ii_write_lock_child(inode);
+			do_put = au_plink_do_half_refresh(inode, br_id);
+			if (do_put) {
+				hlist_bl_del(&icntnr->plink);
+				iput(inode);
+			}
+			ii_write_unlock(inode);
+			iput(inode);
+		}
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/poll.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/poll.c
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * poll operation
+ * There is only one filesystem which implements ->poll operation, currently.
+ */
+
+#include "aufs.h"
+
+__poll_t aufs_poll(struct file *file, struct poll_table_struct *pt)
+{
+	__poll_t mask;
+	struct file *h_file;
+	struct super_block *sb;
+
+	/* We should pretend an error happened. */
+	mask = EPOLLERR /* | EPOLLIN | EPOLLOUT */;
+	sb = file->f_path.dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLMW);
+
+	h_file = au_read_pre(file, /*keep_fi*/0, /*lsc*/0);
+	if (IS_ERR(h_file)) {
+		AuDbg("h_file %ld\n", PTR_ERR(h_file));
+		goto out;
+	}
+
+	mask = vfs_poll(h_file, pt);
+	fput(h_file); /* instead of au_read_post() */
+
+out:
+	si_read_unlock(sb);
+	if (mask & EPOLLERR)
+		AuDbg("mask 0x%x\n", mask);
+	return mask;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/posix_acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/posix_acl.c
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2014-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * posix acl operations
+ */
+
+#include <linux/fs.h>
+#include "aufs.h"
+
+struct posix_acl *aufs_get_acl(struct inode *inode, int type, bool rcu)
+{
+	struct posix_acl *acl;
+	int err;
+	aufs_bindex_t bindex;
+	struct inode *h_inode;
+	struct super_block *sb;
+
+	acl = ERR_PTR(-ECHILD);
+	if (rcu)
+		goto out;
+
+	acl = NULL;
+	sb = inode->i_sb;
+	si_read_lock(sb, AuLock_FLUSH);
+	ii_read_lock_child(inode);
+	if (!(sb->s_flags & SB_POSIXACL))
+		goto unlock;
+
+	bindex = au_ibtop(inode);
+	h_inode = au_h_iptr(inode, bindex);
+	if (unlikely(!h_inode
+		     || ((h_inode->i_mode & S_IFMT)
+			 != (inode->i_mode & S_IFMT)))) {
+		err = au_busy_or_stale();
+		acl = ERR_PTR(err);
+		goto unlock;
+	}
+
+	/* always topmost only */
+	acl = get_acl(h_inode, type);
+	if (IS_ERR(acl))
+		forget_cached_acl(inode, type);
+	else
+		set_cached_acl(inode, type, acl);
+
+unlock:
+	ii_read_unlock(inode);
+	si_read_unlock(sb);
+
+out:
+	AuTraceErrPtr(acl);
+	return acl;
+}
+
+int aufs_set_acl(struct user_namespace *userns, struct inode *inode,
+		 struct posix_acl *acl, int type)
+{
+	int err;
+	ssize_t ssz;
+	struct dentry *dentry;
+	struct au_sxattr arg = {
+		.type = AU_ACL_SET,
+		.u.acl_set = {
+			.acl	= acl,
+			.type	= type
+		},
+	};
+
+	IMustLock(inode);
+
+	if (inode->i_ino == AUFS_ROOT_INO)
+		dentry = dget(inode->i_sb->s_root);
+	else {
+		dentry = d_find_alias(inode);
+		if (!dentry)
+			dentry = d_find_any_alias(inode);
+		if (!dentry) {
+			pr_warn("cannot handle this inode, "
+				"please report to aufs-users ML\n");
+			err = -ENOENT;
+			goto out;
+		}
+	}
+
+	ssz = au_sxattr(dentry, inode, &arg);
+	/* forget even it if succeeds since the branch might set differently */
+	forget_cached_acl(inode, type);
+	dput(dentry);
+	err = ssz;
+	if (ssz >= 0)
+		err = 0;
+
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/procfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/procfs.c
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2010-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * procfs interfaces
+ */
+
+#include <linux/proc_fs.h>
+#include "aufs.h"
+
+static int au_procfs_plm_release(struct inode *inode, struct file *file)
+{
+	struct au_sbinfo *sbinfo;
+
+	sbinfo = file->private_data;
+	if (sbinfo) {
+		au_plink_maint_leave(sbinfo);
+		kobject_put(&sbinfo->si_kobj);
+	}
+
+	return 0;
+}
+
+static void au_procfs_plm_write_clean(struct file *file)
+{
+	struct au_sbinfo *sbinfo;
+
+	sbinfo = file->private_data;
+	if (sbinfo)
+		au_plink_clean(sbinfo->si_sb, /*verbose*/0);
+}
+
+static int au_procfs_plm_write_si(struct file *file, unsigned long id)
+{
+	int err;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_node *pos;
+
+	err = -EBUSY;
+	if (unlikely(file->private_data))
+		goto out;
+
+	sb = NULL;
+	/* don't use au_sbilist_lock() here */
+	hlist_bl_lock(&au_sbilist);
+	hlist_bl_for_each_entry(sbinfo, pos, &au_sbilist, si_list)
+		if (id == sysaufs_si_id(sbinfo)) {
+			if (kobject_get_unless_zero(&sbinfo->si_kobj))
+				sb = sbinfo->si_sb;
+			break;
+		}
+	hlist_bl_unlock(&au_sbilist);
+
+	err = -EINVAL;
+	if (unlikely(!sb))
+		goto out;
+
+	err = au_plink_maint_enter(sb);
+	if (!err)
+		/* keep kobject_get() */
+		file->private_data = sbinfo;
+	else
+		kobject_put(&sbinfo->si_kobj);
+out:
+	return err;
+}
+
+/*
+ * Accept a valid "si=xxxx" only.
+ * Once it is accepted successfully, accept "clean" too.
+ */
+static ssize_t au_procfs_plm_write(struct file *file, const char __user *ubuf,
+				   size_t count, loff_t *ppos)
+{
+	ssize_t err;
+	unsigned long id;
+	/* last newline is allowed */
+	char buf[3 + sizeof(unsigned long) * 2 + 1];
+
+	err = -EACCES;
+	if (unlikely(!capable(CAP_SYS_ADMIN)))
+		goto out;
+
+	err = -EINVAL;
+	if (unlikely(count > sizeof(buf)))
+		goto out;
+
+	err = copy_from_user(buf, ubuf, count);
+	if (unlikely(err)) {
+		err = -EFAULT;
+		goto out;
+	}
+	buf[count] = 0;
+
+	err = -EINVAL;
+	if (!strcmp("clean", buf)) {
+		au_procfs_plm_write_clean(file);
+		goto out_success;
+	} else if (unlikely(strncmp("si=", buf, 3)))
+		goto out;
+
+	err = kstrtoul(buf + 3, 16, &id);
+	if (unlikely(err))
+		goto out;
+
+	err = au_procfs_plm_write_si(file, id);
+	if (unlikely(err))
+		goto out;
+
+out_success:
+	err = count; /* success */
+out:
+	return err;
+}
+
+static const struct proc_ops au_procfs_plm_op = {
+	.proc_write	= au_procfs_plm_write,
+	.proc_release	= au_procfs_plm_release
+};
+
+/* ---------------------------------------------------------------------- */
+
+static struct proc_dir_entry *au_procfs_dir;
+
+void au_procfs_fin(void)
+{
+	remove_proc_entry(AUFS_PLINK_MAINT_NAME, au_procfs_dir);
+	remove_proc_entry(AUFS_PLINK_MAINT_DIR, NULL);
+}
+
+int __init au_procfs_init(void)
+{
+	int err;
+	struct proc_dir_entry *entry;
+
+	err = -ENOMEM;
+	au_procfs_dir = proc_mkdir(AUFS_PLINK_MAINT_DIR, NULL);
+	if (unlikely(!au_procfs_dir))
+		goto out;
+
+	entry = proc_create(AUFS_PLINK_MAINT_NAME, S_IFREG | 0200,
+			    au_procfs_dir, &au_procfs_plm_op);
+	if (unlikely(!entry))
+		goto out_dir;
+
+	err = 0;
+	goto out; /* success */
+
+
+out_dir:
+	remove_proc_entry(AUFS_PLINK_MAINT_DIR, NULL);
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/rdu.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/rdu.c
@@ -0,0 +1,384 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * readdir in userspace.
+ */
+
+#include <linux/compat.h>
+#include <linux/fs_stack.h>
+#include <linux/security.h>
+#include "aufs.h"
+
+/* bits for struct aufs_rdu.flags */
+#define	AuRdu_CALLED	1
+#define	AuRdu_CONT	(1 << 1)
+#define	AuRdu_FULL	(1 << 2)
+#define au_ftest_rdu(flags, name)	((flags) & AuRdu_##name)
+#define au_fset_rdu(flags, name) \
+	do { (flags) |= AuRdu_##name; } while (0)
+#define au_fclr_rdu(flags, name) \
+	do { (flags) &= ~AuRdu_##name; } while (0)
+
+struct au_rdu_arg {
+	struct dir_context		ctx;
+	struct aufs_rdu			*rdu;
+	union au_rdu_ent_ul		ent;
+	unsigned long			end;
+
+	struct super_block		*sb;
+	int				err;
+};
+
+static int au_rdu_fill(struct dir_context *ctx, const char *name, int nlen,
+		       loff_t offset, u64 h_ino, unsigned int d_type)
+{
+	int err, len;
+	struct au_rdu_arg *arg = container_of(ctx, struct au_rdu_arg, ctx);
+	struct aufs_rdu *rdu = arg->rdu;
+	struct au_rdu_ent ent;
+
+	err = 0;
+	arg->err = 0;
+	au_fset_rdu(rdu->cookie.flags, CALLED);
+	len = au_rdu_len(nlen);
+	if (arg->ent.ul + len  < arg->end) {
+		ent.ino = h_ino;
+		ent.bindex = rdu->cookie.bindex;
+		ent.type = d_type;
+		ent.nlen = nlen;
+		if (unlikely(nlen > AUFS_MAX_NAMELEN))
+			ent.type = DT_UNKNOWN;
+
+		/* unnecessary to support mmap_sem since this is a dir */
+		err = -EFAULT;
+		if (copy_to_user(arg->ent.e, &ent, sizeof(ent)))
+			goto out;
+		if (copy_to_user(arg->ent.e->name, name, nlen))
+			goto out;
+		/* the terminating NULL */
+		if (__put_user(0, arg->ent.e->name + nlen))
+			goto out;
+		err = 0;
+		/* AuDbg("%p, %.*s\n", arg->ent.p, nlen, name); */
+		arg->ent.ul += len;
+		rdu->rent++;
+	} else {
+		err = -EFAULT;
+		au_fset_rdu(rdu->cookie.flags, FULL);
+		rdu->full = 1;
+		rdu->tail = arg->ent;
+	}
+
+out:
+	/* AuTraceErr(err); */
+	return err;
+}
+
+static int au_rdu_do(struct file *h_file, struct au_rdu_arg *arg)
+{
+	int err;
+	loff_t offset;
+	struct au_rdu_cookie *cookie = &arg->rdu->cookie;
+
+	/* we don't have to care (FMODE_32BITHASH | FMODE_64BITHASH) for ext4 */
+	offset = vfsub_llseek(h_file, cookie->h_pos, SEEK_SET);
+	err = offset;
+	if (unlikely(offset != cookie->h_pos))
+		goto out;
+
+	err = 0;
+	do {
+		arg->err = 0;
+		au_fclr_rdu(cookie->flags, CALLED);
+		/* smp_mb(); */
+		err = vfsub_iterate_dir(h_file, &arg->ctx);
+		if (err >= 0)
+			err = arg->err;
+	} while (!err
+		 && au_ftest_rdu(cookie->flags, CALLED)
+		 && !au_ftest_rdu(cookie->flags, FULL));
+	cookie->h_pos = h_file->f_pos;
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_rdu(struct file *file, struct aufs_rdu *rdu)
+{
+	int err;
+	aufs_bindex_t bbot;
+	struct au_rdu_arg arg = {
+		.ctx = {
+			.actor = au_rdu_fill
+		}
+	};
+	struct dentry *dentry;
+	struct inode *inode;
+	struct file *h_file;
+	struct au_rdu_cookie *cookie = &rdu->cookie;
+
+	/* VERIFY_WRITE */
+	err = !access_ok(rdu->ent.e, rdu->sz);
+	if (unlikely(err)) {
+		err = -EFAULT;
+		AuTraceErr(err);
+		goto out;
+	}
+	rdu->rent = 0;
+	rdu->tail = rdu->ent;
+	rdu->full = 0;
+	arg.rdu = rdu;
+	arg.ent = rdu->ent;
+	arg.end = arg.ent.ul;
+	arg.end += rdu->sz;
+
+	err = -ENOTDIR;
+	if (unlikely(!file->f_op->iterate && !file->f_op->iterate_shared))
+		goto out;
+
+	err = security_file_permission(file, MAY_READ);
+	AuTraceErr(err);
+	if (unlikely(err))
+		goto out;
+
+	dentry = file->f_path.dentry;
+	inode = d_inode(dentry);
+	inode_lock_shared(inode);
+
+	arg.sb = inode->i_sb;
+	err = si_read_lock(arg.sb, AuLock_FLUSH | AuLock_NOPLM);
+	if (unlikely(err))
+		goto out_mtx;
+	err = au_alive_dir(dentry);
+	if (unlikely(err))
+		goto out_si;
+	/* todo: reval? */
+	fi_read_lock(file);
+
+	err = -EAGAIN;
+	if (unlikely(au_ftest_rdu(cookie->flags, CONT)
+		     && cookie->generation != au_figen(file)))
+		goto out_unlock;
+
+	err = 0;
+	if (!rdu->blk) {
+		rdu->blk = au_sbi(arg.sb)->si_rdblk;
+		if (!rdu->blk)
+			rdu->blk = au_dir_size(file, /*dentry*/NULL);
+	}
+	bbot = au_fbtop(file);
+	if (cookie->bindex < bbot)
+		cookie->bindex = bbot;
+	bbot = au_fbbot_dir(file);
+	/* AuDbg("b%d, b%d\n", cookie->bindex, bbot); */
+	for (; !err && cookie->bindex <= bbot;
+	     cookie->bindex++, cookie->h_pos = 0) {
+		h_file = au_hf_dir(file, cookie->bindex);
+		if (!h_file)
+			continue;
+
+		au_fclr_rdu(cookie->flags, FULL);
+		err = au_rdu_do(h_file, &arg);
+		AuTraceErr(err);
+		if (unlikely(au_ftest_rdu(cookie->flags, FULL) || err))
+			break;
+	}
+	AuDbg("rent %llu\n", rdu->rent);
+
+	if (!err && !au_ftest_rdu(cookie->flags, CONT)) {
+		rdu->shwh = !!au_opt_test(au_sbi(arg.sb)->si_mntflags, SHWH);
+		au_fset_rdu(cookie->flags, CONT);
+		cookie->generation = au_figen(file);
+	}
+
+	ii_read_lock_child(inode);
+	fsstack_copy_attr_atime(inode, au_h_iptr(inode, au_ibtop(inode)));
+	ii_read_unlock(inode);
+
+out_unlock:
+	fi_read_unlock(file);
+out_si:
+	si_read_unlock(arg.sb);
+out_mtx:
+	inode_unlock_shared(inode);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_rdu_ino(struct file *file, struct aufs_rdu *rdu)
+{
+	int err;
+	ino_t ino;
+	unsigned long long nent;
+	union au_rdu_ent_ul *u;
+	struct au_rdu_ent ent;
+	struct super_block *sb;
+
+	err = 0;
+	nent = rdu->nent;
+	u = &rdu->ent;
+	sb = file->f_path.dentry->d_sb;
+	si_read_lock(sb, AuLock_FLUSH);
+	while (nent-- > 0) {
+		/* unnecessary to support mmap_sem since this is a dir */
+		err = copy_from_user(&ent, u->e, sizeof(ent));
+		if (!err)
+			/* VERIFY_WRITE */
+			err = !access_ok(&u->e->ino, sizeof(ino));
+		if (unlikely(err)) {
+			err = -EFAULT;
+			AuTraceErr(err);
+			break;
+		}
+
+		/* AuDbg("b%d, i%llu\n", ent.bindex, ent.ino); */
+		if (!ent.wh)
+			err = au_ino(sb, ent.bindex, ent.ino, ent.type, &ino);
+		else
+			err = au_wh_ino(sb, ent.bindex, ent.ino, ent.type,
+					&ino);
+		if (unlikely(err)) {
+			AuTraceErr(err);
+			break;
+		}
+
+		err = __put_user(ino, &u->e->ino);
+		if (unlikely(err)) {
+			err = -EFAULT;
+			AuTraceErr(err);
+			break;
+		}
+		u->ul += au_rdu_len(ent.nlen);
+	}
+	si_read_unlock(sb);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_rdu_verify(struct aufs_rdu *rdu)
+{
+	AuDbg("rdu{%llu, %p, %u | %u | %llu, %u, %u | "
+	      "%llu, b%d, 0x%x, g%u}\n",
+	      rdu->sz, rdu->ent.e, rdu->verify[AufsCtlRduV_SZ],
+	      rdu->blk,
+	      rdu->rent, rdu->shwh, rdu->full,
+	      rdu->cookie.h_pos, rdu->cookie.bindex, rdu->cookie.flags,
+	      rdu->cookie.generation);
+
+	if (rdu->verify[AufsCtlRduV_SZ] == sizeof(*rdu))
+		return 0;
+
+	AuDbg("%u:%u\n",
+	      rdu->verify[AufsCtlRduV_SZ], (unsigned int)sizeof(*rdu));
+	return -EINVAL;
+}
+
+long au_rdu_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	long err, e;
+	struct aufs_rdu rdu;
+	void __user *p = (void __user *)arg;
+
+	err = copy_from_user(&rdu, p, sizeof(rdu));
+	if (unlikely(err)) {
+		err = -EFAULT;
+		AuTraceErr(err);
+		goto out;
+	}
+	err = au_rdu_verify(&rdu);
+	if (unlikely(err))
+		goto out;
+
+	switch (cmd) {
+	case AUFS_CTL_RDU:
+		err = au_rdu(file, &rdu);
+		if (unlikely(err))
+			break;
+
+		e = copy_to_user(p, &rdu, sizeof(rdu));
+		if (unlikely(e)) {
+			err = -EFAULT;
+			AuTraceErr(err);
+		}
+		break;
+	case AUFS_CTL_RDU_INO:
+		err = au_rdu_ino(file, &rdu);
+		break;
+
+	default:
+		/* err = -ENOTTY; */
+		err = -EINVAL;
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+#ifdef CONFIG_COMPAT
+long au_rdu_compat_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	long err, e;
+	struct aufs_rdu rdu;
+	void __user *p = compat_ptr(arg);
+
+	/* todo: get_user()? */
+	err = copy_from_user(&rdu, p, sizeof(rdu));
+	if (unlikely(err)) {
+		err = -EFAULT;
+		AuTraceErr(err);
+		goto out;
+	}
+	rdu.ent.e = compat_ptr(rdu.ent.ul);
+	err = au_rdu_verify(&rdu);
+	if (unlikely(err))
+		goto out;
+
+	switch (cmd) {
+	case AUFS_CTL_RDU:
+		err = au_rdu(file, &rdu);
+		if (unlikely(err))
+			break;
+
+		rdu.ent.ul = ptr_to_compat(rdu.ent.e);
+		rdu.tail.ul = ptr_to_compat(rdu.tail.e);
+		e = copy_to_user(p, &rdu, sizeof(rdu));
+		if (unlikely(e)) {
+			err = -EFAULT;
+			AuTraceErr(err);
+		}
+		break;
+	case AUFS_CTL_RDU_INO:
+		err = au_rdu_ino(file, &rdu);
+		break;
+
+	default:
+		/* err = -ENOTTY; */
+		err = -EINVAL;
+	}
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/rwsem.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/rwsem.h
@@ -0,0 +1,85 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * simple read-write semaphore wrappers
+ */
+
+#ifndef __AUFS_RWSEM_H__
+#define __AUFS_RWSEM_H__
+
+#ifdef __KERNEL__
+
+#include "debug.h"
+
+/* in the future, the name 'au_rwsem' will be totally gone */
+#define au_rwsem	rw_semaphore
+
+/* to debug easier, do not make them inlined functions */
+#define AuRwMustNoWaiters(rw)	AuDebugOn(rwsem_is_contended(rw))
+
+#ifdef CONFIG_LOCKDEP
+/* rwsem_is_locked() is unusable */
+#define AuRwMustReadLock(rw)	AuDebugOn(IS_ENABLED(CONFIG_LOCKDEP)	\
+					  && !lockdep_recursing(current) \
+					  && debug_locks		\
+					  && !lockdep_is_held_type(rw, 1))
+#define AuRwMustWriteLock(rw)	AuDebugOn(IS_ENABLED(CONFIG_LOCKDEP)	\
+					  && !lockdep_recursing(current) \
+					  && debug_locks		\
+					  && !lockdep_is_held_type(rw, 0))
+#define AuRwMustAnyLock(rw)	AuDebugOn(IS_ENABLED(CONFIG_LOCKDEP)	\
+					  && !lockdep_recursing(current) \
+					  && debug_locks		\
+					  && !lockdep_is_held(rw))
+#define AuRwDestroy(rw)		AuDebugOn(IS_ENABLED(CONFIG_LOCKDEP)	\
+					  && !lockdep_recursing(current) \
+					  && debug_locks		\
+					  && lockdep_is_held(rw))
+#else
+#define AuRwMustReadLock(rw)	do {} while (0)
+#define AuRwMustWriteLock(rw)	do {} while (0)
+#define AuRwMustAnyLock(rw)	do {} while (0)
+#define AuRwDestroy(rw)		do {} while (0)
+#endif
+
+#define au_rw_init(rw)	init_rwsem(rw)
+
+#define au_rw_init_wlock(rw) do {		\
+		au_rw_init(rw);			\
+		down_write(rw);			\
+	} while (0)
+
+#define au_rw_init_wlock_nested(rw, lsc) do {	\
+		au_rw_init(rw);			\
+		down_write_nested(rw, lsc);	\
+	} while (0)
+
+#define au_rw_read_lock(rw)		down_read(rw)
+#define au_rw_read_lock_nested(rw, lsc)	down_read_nested(rw, lsc)
+#define au_rw_read_unlock(rw)		up_read(rw)
+#define au_rw_dgrade_lock(rw)		downgrade_write(rw)
+#define au_rw_write_lock(rw)		down_write(rw)
+#define au_rw_write_lock_nested(rw, lsc) down_write_nested(rw, lsc)
+#define au_rw_write_unlock(rw)		up_write(rw)
+/* why is not _nested version defined? */
+#define au_rw_read_trylock(rw)		down_read_trylock(rw)
+#define au_rw_write_trylock(rw)		down_write_trylock(rw)
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_RWSEM_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/sbinfo.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/sbinfo.c
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * superblock private data
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+/*
+ * they are necessary regardless sysfs is disabled.
+ */
+void au_si_free(struct kobject *kobj)
+{
+	int i;
+	struct au_sbinfo *sbinfo;
+	char *locked __maybe_unused; /* debug only */
+
+	sbinfo = container_of(kobj, struct au_sbinfo, si_kobj);
+	for (i = 0; i < AuPlink_NHASH; i++)
+		AuDebugOn(!hlist_bl_empty(sbinfo->si_plink + i));
+	AuDebugOn(atomic_read(&sbinfo->si_nowait.nw_len));
+
+	AuLCntZero(au_lcnt_read(&sbinfo->si_ninodes, /*do_rev*/0));
+	au_lcnt_fin(&sbinfo->si_ninodes, /*do_sync*/0);
+	AuLCntZero(au_lcnt_read(&sbinfo->si_nfiles, /*do_rev*/0));
+	au_lcnt_fin(&sbinfo->si_nfiles, /*do_sync*/0);
+
+	dbgaufs_si_fin(sbinfo);
+	au_rw_write_lock(&sbinfo->si_rwsem);
+	au_br_free(sbinfo);
+	au_rw_write_unlock(&sbinfo->si_rwsem);
+
+	au_kfree_try_rcu(sbinfo->si_branch);
+	mutex_destroy(&sbinfo->si_xib_mtx);
+	AuRwDestroy(&sbinfo->si_rwsem);
+
+	au_lcnt_wait_for_fin(&sbinfo->si_ninodes);
+	/* si_nfiles is waited too */
+	au_kfree_rcu(sbinfo);
+}
+
+int au_si_alloc(struct super_block *sb)
+{
+	int err, i;
+	struct au_sbinfo *sbinfo;
+
+	err = -ENOMEM;
+	sbinfo = kzalloc(sizeof(*sbinfo), GFP_NOFS);
+	if (unlikely(!sbinfo))
+		goto out;
+
+	/* will be reallocated separately */
+	sbinfo->si_branch = kzalloc(sizeof(*sbinfo->si_branch), GFP_NOFS);
+	if (unlikely(!sbinfo->si_branch))
+		goto out_sbinfo;
+
+	err = sysaufs_si_init(sbinfo);
+	if (!err) {
+		dbgaufs_si_null(sbinfo);
+		err = dbgaufs_si_init(sbinfo);
+		if (unlikely(err))
+			kobject_put(&sbinfo->si_kobj);
+	}
+	if (unlikely(err))
+		goto out_br;
+
+	au_nwt_init(&sbinfo->si_nowait);
+	au_rw_init_wlock(&sbinfo->si_rwsem);
+
+	au_lcnt_init(&sbinfo->si_ninodes, /*release*/NULL);
+	au_lcnt_init(&sbinfo->si_nfiles, /*release*/NULL);
+
+	sbinfo->si_bbot = -1;
+	sbinfo->si_last_br_id = AUFS_BRANCH_MAX / 2;
+
+	sbinfo->si_wbr_copyup = AuWbrCopyup_Def;
+	sbinfo->si_wbr_create = AuWbrCreate_Def;
+	sbinfo->si_wbr_copyup_ops = au_wbr_copyup_ops + sbinfo->si_wbr_copyup;
+	sbinfo->si_wbr_create_ops = au_wbr_create_ops + sbinfo->si_wbr_create;
+
+	au_fhsm_init(sbinfo);
+
+	sbinfo->si_mntflags = au_opts_plink(AuOpt_Def);
+
+	sbinfo->si_xino_jiffy = jiffies;
+	sbinfo->si_xino_expire
+		= msecs_to_jiffies(AUFS_XINO_DEF_SEC * MSEC_PER_SEC);
+	mutex_init(&sbinfo->si_xib_mtx);
+	/* leave si_xib_last_pindex and si_xib_next_bit */
+
+	INIT_HLIST_BL_HEAD(&sbinfo->si_aopen);
+
+	sbinfo->si_rdcache = msecs_to_jiffies(AUFS_RDCACHE_DEF * MSEC_PER_SEC);
+	sbinfo->si_rdblk = AUFS_RDBLK_DEF;
+	sbinfo->si_rdhash = AUFS_RDHASH_DEF;
+	sbinfo->si_dirwh = AUFS_DIRWH_DEF;
+
+	for (i = 0; i < AuPlink_NHASH; i++)
+		INIT_HLIST_BL_HEAD(sbinfo->si_plink + i);
+	init_waitqueue_head(&sbinfo->si_plink_wq);
+	spin_lock_init(&sbinfo->si_plink_maint_lock);
+
+	INIT_HLIST_BL_HEAD(&sbinfo->si_files);
+
+	/* with getattr by default */
+	sbinfo->si_iop_array = aufs_iop;
+
+	/* leave other members for sysaufs and si_mnt. */
+	sbinfo->si_sb = sb;
+	sb->s_fs_info = sbinfo;
+	si_pid_set(sb);
+	return 0; /* success */
+
+out_br:
+	au_kfree_try_rcu(sbinfo->si_branch);
+out_sbinfo:
+	au_kfree_rcu(sbinfo);
+out:
+	return err;
+}
+
+int au_sbr_realloc(struct au_sbinfo *sbinfo, int nbr, int may_shrink)
+{
+	int err, sz;
+	struct au_branch **brp;
+
+	AuRwMustWriteLock(&sbinfo->si_rwsem);
+
+	err = -ENOMEM;
+	sz = sizeof(*brp) * (sbinfo->si_bbot + 1);
+	if (unlikely(!sz))
+		sz = sizeof(*brp);
+	brp = au_kzrealloc(sbinfo->si_branch, sz, sizeof(*brp) * nbr, GFP_NOFS,
+			   may_shrink);
+	if (brp) {
+		sbinfo->si_branch = brp;
+		err = 0;
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+unsigned int au_sigen_inc(struct super_block *sb)
+{
+	unsigned int gen;
+	struct inode *inode;
+
+	SiMustWriteLock(sb);
+
+	gen = ++au_sbi(sb)->si_generation;
+	au_update_digen(sb->s_root);
+	inode = d_inode(sb->s_root);
+	au_update_iigen(inode, /*half*/0);
+	inode_inc_iversion(inode);
+	return gen;
+}
+
+aufs_bindex_t au_new_br_id(struct super_block *sb)
+{
+	aufs_bindex_t br_id;
+	int i;
+	struct au_sbinfo *sbinfo;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	for (i = 0; i <= AUFS_BRANCH_MAX; i++) {
+		br_id = ++sbinfo->si_last_br_id;
+		AuDebugOn(br_id < 0);
+		if (br_id && au_br_index(sb, br_id) < 0)
+			return br_id;
+	}
+
+	return -1;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* it is ok that new 'nwt' tasks are appended while we are sleeping */
+int si_read_lock(struct super_block *sb, int flags)
+{
+	int err;
+
+	err = 0;
+	if (au_ftest_lock(flags, FLUSH))
+		au_nwt_flush(&au_sbi(sb)->si_nowait);
+
+	si_noflush_read_lock(sb);
+	err = au_plink_maint(sb, flags);
+	if (unlikely(err))
+		si_read_unlock(sb);
+
+	return err;
+}
+
+int si_write_lock(struct super_block *sb, int flags)
+{
+	int err;
+
+	if (au_ftest_lock(flags, FLUSH))
+		au_nwt_flush(&au_sbi(sb)->si_nowait);
+
+	si_noflush_write_lock(sb);
+	err = au_plink_maint(sb, flags);
+	if (unlikely(err))
+		si_write_unlock(sb);
+
+	return err;
+}
+
+/* dentry and super_block lock. call at entry point */
+int aufs_read_lock(struct dentry *dentry, int flags)
+{
+	int err;
+	struct super_block *sb;
+
+	sb = dentry->d_sb;
+	err = si_read_lock(sb, flags);
+	if (unlikely(err))
+		goto out;
+
+	if (au_ftest_lock(flags, DW))
+		di_write_lock_child(dentry);
+	else
+		di_read_lock_child(dentry, flags);
+
+	if (au_ftest_lock(flags, GEN)) {
+		err = au_digen_test(dentry, au_sigen(sb));
+		if (!au_opt_test(au_mntflags(sb), UDBA_NONE))
+			AuDebugOn(!err && au_dbrange_test(dentry));
+		else if (!err)
+			err = au_dbrange_test(dentry);
+		if (unlikely(err))
+			aufs_read_unlock(dentry, flags);
+	}
+
+out:
+	return err;
+}
+
+void aufs_read_unlock(struct dentry *dentry, int flags)
+{
+	if (au_ftest_lock(flags, DW))
+		di_write_unlock(dentry);
+	else
+		di_read_unlock(dentry, flags);
+	si_read_unlock(dentry->d_sb);
+}
+
+void aufs_write_lock(struct dentry *dentry)
+{
+	si_write_lock(dentry->d_sb, AuLock_FLUSH | AuLock_NOPLMW);
+	di_write_lock_child(dentry);
+}
+
+void aufs_write_unlock(struct dentry *dentry)
+{
+	di_write_unlock(dentry);
+	si_write_unlock(dentry->d_sb);
+}
+
+int aufs_read_and_write_lock2(struct dentry *d1, struct dentry *d2, int flags)
+{
+	int err;
+	unsigned int sigen;
+	struct super_block *sb;
+
+	sb = d1->d_sb;
+	err = si_read_lock(sb, flags);
+	if (unlikely(err))
+		goto out;
+
+	di_write_lock2_child(d1, d2, au_ftest_lock(flags, DIRS));
+
+	if (au_ftest_lock(flags, GEN)) {
+		sigen = au_sigen(sb);
+		err = au_digen_test(d1, sigen);
+		AuDebugOn(!err && au_dbrange_test(d1));
+		if (!err) {
+			err = au_digen_test(d2, sigen);
+			AuDebugOn(!err && au_dbrange_test(d2));
+		}
+		if (unlikely(err))
+			aufs_read_and_write_unlock2(d1, d2);
+	}
+
+out:
+	return err;
+}
+
+void aufs_read_and_write_unlock2(struct dentry *d1, struct dentry *d2)
+{
+	di_write_unlock2(d1, d2);
+	si_read_unlock(d1->d_sb);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/super.c
@@ -0,0 +1,1053 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * mount and super_block operations
+ */
+
+#include <linux/iversion.h>
+#include <linux/mm.h>
+#include <linux/seq_file.h>
+#include <linux/statfs.h>
+#include <linux/vmalloc.h>
+#include "aufs.h"
+
+/*
+ * super_operations
+ */
+static struct inode *aufs_alloc_inode(struct super_block *sb __maybe_unused)
+{
+	struct au_icntnr *c;
+
+	c = au_cache_alloc_icntnr();
+	if (c) {
+		au_icntnr_init(c);
+		inode_set_iversion(&c->vfs_inode, 1); /* sigen(sb); */
+		c->iinfo.ii_hinode = NULL;
+		return &c->vfs_inode;
+	}
+	return NULL;
+}
+
+static void aufs_destroy_inode(struct inode *inode)
+{
+	if (!au_is_bad_inode(inode))
+		au_iinfo_fin(inode);
+}
+
+static void aufs_free_inode(struct inode *inode)
+{
+	au_cache_free_icntnr(container_of(inode, struct au_icntnr, vfs_inode));
+}
+
+struct inode *au_iget_locked(struct super_block *sb, ino_t ino)
+{
+	struct inode *inode;
+	int err;
+
+	inode = iget_locked(sb, ino);
+	if (unlikely(!inode)) {
+		inode = ERR_PTR(-ENOMEM);
+		goto out;
+	}
+	if (!(inode->i_state & I_NEW))
+		goto out;
+
+	err = au_xigen_new(inode);
+	if (!err)
+		err = au_iinfo_init(inode);
+	if (!err)
+		inode_inc_iversion(inode);
+	else {
+		iget_failed(inode);
+		inode = ERR_PTR(err);
+	}
+
+out:
+	/* never return NULL */
+	AuDebugOn(!inode);
+	AuTraceErrPtr(inode);
+	return inode;
+}
+
+/* lock free root dinfo */
+static int au_show_brs(struct seq_file *seq, struct super_block *sb)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct path path;
+	struct au_hdentry *hdp;
+	struct au_branch *br;
+	au_br_perm_str_t perm;
+
+	err = 0;
+	bbot = au_sbbot(sb);
+	bindex = 0;
+	hdp = au_hdentry(au_di(sb->s_root), bindex);
+	for (; !err && bindex <= bbot; bindex++, hdp++) {
+		br = au_sbr(sb, bindex);
+		path.mnt = au_br_mnt(br);
+		path.dentry = hdp->hd_dentry;
+		err = au_seq_path(seq, &path);
+		if (!err) {
+			au_optstr_br_perm(&perm, br->br_perm);
+			seq_printf(seq, "=%s", perm.a);
+			if (bindex != bbot)
+				seq_putc(seq, ':');
+		}
+	}
+	if (unlikely(err || seq_has_overflowed(seq)))
+		err = -E2BIG;
+
+	return err;
+}
+
+static void au_gen_fmt(char *fmt, int len __maybe_unused, const char *pat,
+		       const char *append)
+{
+	char *p;
+
+	p = fmt;
+	while (*pat != ':')
+		*p++ = *pat++;
+	*p++ = *pat++;
+	strcpy(p, append);
+	AuDebugOn(strlen(fmt) >= len);
+}
+
+static void au_show_wbr_create(struct seq_file *m, int v,
+			       struct au_sbinfo *sbinfo)
+{
+	const char *pat;
+	char fmt[32];
+	struct au_wbr_mfs *mfs;
+
+	AuRwMustAnyLock(&sbinfo->si_rwsem);
+
+	seq_puts(m, ",create=");
+	pat = au_optstr_wbr_create(v);
+	mfs = &sbinfo->si_wbr_mfs;
+	switch (v) {
+	case AuWbrCreate_TDP:
+	case AuWbrCreate_RR:
+	case AuWbrCreate_MFS:
+	case AuWbrCreate_PMFS:
+		seq_puts(m, pat);
+		break;
+	case AuWbrCreate_MFSRR:
+	case AuWbrCreate_TDMFS:
+	case AuWbrCreate_PMFSRR:
+		au_gen_fmt(fmt, sizeof(fmt), pat, "%llu");
+		seq_printf(m, fmt, mfs->mfsrr_watermark);
+		break;
+	case AuWbrCreate_MFSV:
+	case AuWbrCreate_PMFSV:
+		au_gen_fmt(fmt, sizeof(fmt), pat, "%lu");
+		seq_printf(m, fmt,
+			   jiffies_to_msecs(mfs->mfs_expire)
+			   / MSEC_PER_SEC);
+		break;
+	case AuWbrCreate_MFSRRV:
+	case AuWbrCreate_TDMFSV:
+	case AuWbrCreate_PMFSRRV:
+		au_gen_fmt(fmt, sizeof(fmt), pat, "%llu:%lu");
+		seq_printf(m, fmt, mfs->mfsrr_watermark,
+			   jiffies_to_msecs(mfs->mfs_expire) / MSEC_PER_SEC);
+		break;
+	default:
+		BUG();
+	}
+}
+
+static int au_show_xino(struct seq_file *seq, struct super_block *sb)
+{
+#ifdef CONFIG_SYSFS
+	return 0;
+#else
+	int err;
+	const int len = sizeof(AUFS_XINO_FNAME) - 1;
+	aufs_bindex_t bindex, brid;
+	struct qstr *name;
+	struct file *f;
+	struct dentry *d, *h_root;
+	struct au_branch *br;
+
+	AuRwMustAnyLock(&sbinfo->si_rwsem);
+
+	err = 0;
+	f = au_sbi(sb)->si_xib;
+	if (!f)
+		goto out;
+
+	/* stop printing the default xino path on the first writable branch */
+	h_root = NULL;
+	bindex = au_xi_root(sb, f->f_path.dentry);
+	if (bindex >= 0) {
+		br = au_sbr_sb(sb, bindex);
+		h_root = au_br_dentry(br);
+	}
+
+	d = f->f_path.dentry;
+	name = &d->d_name;
+	/* safe ->d_parent because the file is unlinked */
+	if (d->d_parent == h_root
+	    && name->len == len
+	    && !memcmp(name->name, AUFS_XINO_FNAME, len))
+		goto out;
+
+	seq_puts(seq, ",xino=");
+	err = au_xino_path(seq, f);
+
+out:
+	return err;
+#endif
+}
+
+/* seq_file will re-call me in case of too long string */
+static int aufs_show_options(struct seq_file *m, struct dentry *dentry)
+{
+	int err;
+	unsigned int mnt_flags, v;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+
+#define AuBool(name, str) do { \
+	v = au_opt_test(mnt_flags, name); \
+	if (v != au_opt_test(AuOpt_Def, name)) \
+		seq_printf(m, ",%s" #str, v ? "" : "no"); \
+} while (0)
+
+#define AuStr(name, str) do { \
+	v = mnt_flags & AuOptMask_##name; \
+	if (v != (AuOpt_Def & AuOptMask_##name)) \
+		seq_printf(m, "," #str "=%s", au_optstr_##str(v)); \
+} while (0)
+
+#define AuUInt(name, str, val) do { \
+	if (val != AUFS_##name##_DEF) \
+		seq_printf(m, "," #str "=%u", val); \
+} while (0)
+
+	sb = dentry->d_sb;
+	if (sb->s_flags & SB_POSIXACL)
+		seq_puts(m, ",acl");
+#if 0 /* reserved for future use */
+	if (sb->s_flags & SB_I_VERSION)
+		seq_puts(m, ",i_version");
+#endif
+
+	/* lock free root dinfo */
+	si_noflush_read_lock(sb);
+	sbinfo = au_sbi(sb);
+	seq_printf(m, ",si=%lx", sysaufs_si_id(sbinfo));
+
+	mnt_flags = au_mntflags(sb);
+	if (au_opt_test(mnt_flags, XINO)) {
+		err = au_show_xino(m, sb);
+		if (unlikely(err))
+			goto out;
+	} else
+		seq_puts(m, ",noxino");
+
+	AuBool(TRUNC_XINO, trunc_xino);
+	AuStr(UDBA, udba);
+	AuBool(SHWH, shwh);
+	AuBool(PLINK, plink);
+	AuBool(DIO, dio);
+	AuBool(DIRPERM1, dirperm1);
+
+	v = sbinfo->si_wbr_create;
+	if (v != AuWbrCreate_Def)
+		au_show_wbr_create(m, v, sbinfo);
+
+	v = sbinfo->si_wbr_copyup;
+	if (v != AuWbrCopyup_Def)
+		seq_printf(m, ",cpup=%s", au_optstr_wbr_copyup(v));
+
+	v = au_opt_test(mnt_flags, ALWAYS_DIROPQ);
+	if (v != au_opt_test(AuOpt_Def, ALWAYS_DIROPQ))
+		seq_printf(m, ",diropq=%c", v ? 'a' : 'w');
+
+	AuUInt(DIRWH, dirwh, sbinfo->si_dirwh);
+
+	v = jiffies_to_msecs(sbinfo->si_rdcache) / MSEC_PER_SEC;
+	AuUInt(RDCACHE, rdcache, v);
+
+	AuUInt(RDBLK, rdblk, sbinfo->si_rdblk);
+	AuUInt(RDHASH, rdhash, sbinfo->si_rdhash);
+
+	au_fhsm_show(m, sbinfo);
+
+	AuBool(DIRREN, dirren);
+	AuBool(SUM, sum);
+	/* AuBool(SUM_W, wsum); */
+	AuBool(WARN_PERM, warn_perm);
+	AuBool(VERBOSE, verbose);
+
+out:
+	/* be sure to print "br:" last */
+	if (!sysaufs_brs) {
+		seq_puts(m, ",br:");
+		au_show_brs(m, sb);
+	}
+	si_read_unlock(sb);
+	return 0;
+
+#undef AuBool
+#undef AuStr
+#undef AuUInt
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* sum mode which returns the summation for statfs(2) */
+
+static u64 au_add_till_max(u64 a, u64 b)
+{
+	u64 old;
+
+	old = a;
+	a += b;
+	if (old <= a)
+		return a;
+	return ULLONG_MAX;
+}
+
+static u64 au_mul_till_max(u64 a, long mul)
+{
+	u64 old;
+
+	old = a;
+	a *= mul;
+	if (old <= a)
+		return a;
+	return ULLONG_MAX;
+}
+
+static int au_statfs_sum(struct super_block *sb, struct kstatfs *buf)
+{
+	int err;
+	long bsize, factor;
+	u64 blocks, bfree, bavail, files, ffree;
+	aufs_bindex_t bbot, bindex, i;
+	unsigned char shared;
+	struct path h_path;
+	struct super_block *h_sb;
+
+	err = 0;
+	bsize = LONG_MAX;
+	files = 0;
+	ffree = 0;
+	blocks = 0;
+	bfree = 0;
+	bavail = 0;
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		h_path.mnt = au_sbr_mnt(sb, bindex);
+		h_sb = h_path.mnt->mnt_sb;
+		shared = 0;
+		for (i = 0; !shared && i < bindex; i++)
+			shared = (au_sbr_sb(sb, i) == h_sb);
+		if (shared)
+			continue;
+
+		/* sb->s_root for NFS is unreliable */
+		h_path.dentry = h_path.mnt->mnt_root;
+		err = vfs_statfs(&h_path, buf);
+		if (unlikely(err))
+			goto out;
+
+		if (bsize > buf->f_bsize) {
+			/*
+			 * we will reduce bsize, so we have to expand blocks
+			 * etc. to match them again
+			 */
+			factor = (bsize / buf->f_bsize);
+			blocks = au_mul_till_max(blocks, factor);
+			bfree = au_mul_till_max(bfree, factor);
+			bavail = au_mul_till_max(bavail, factor);
+			bsize = buf->f_bsize;
+		}
+
+		factor = (buf->f_bsize / bsize);
+		blocks = au_add_till_max(blocks,
+				au_mul_till_max(buf->f_blocks, factor));
+		bfree = au_add_till_max(bfree,
+				au_mul_till_max(buf->f_bfree, factor));
+		bavail = au_add_till_max(bavail,
+				au_mul_till_max(buf->f_bavail, factor));
+		files = au_add_till_max(files, buf->f_files);
+		ffree = au_add_till_max(ffree, buf->f_ffree);
+	}
+
+	buf->f_bsize = bsize;
+	buf->f_blocks = blocks;
+	buf->f_bfree = bfree;
+	buf->f_bavail = bavail;
+	buf->f_files = files;
+	buf->f_ffree = ffree;
+	buf->f_frsize = 0;
+
+out:
+	return err;
+}
+
+static int aufs_statfs(struct dentry *dentry, struct kstatfs *buf)
+{
+	int err;
+	struct path h_path;
+	struct super_block *sb;
+
+	/* lock free root dinfo */
+	sb = dentry->d_sb;
+	si_noflush_read_lock(sb);
+	if (!au_opt_test(au_mntflags(sb), SUM)) {
+		/* sb->s_root for NFS is unreliable */
+		h_path.mnt = au_sbr_mnt(sb, 0);
+		h_path.dentry = h_path.mnt->mnt_root;
+		err = vfs_statfs(&h_path, buf);
+	} else
+		err = au_statfs_sum(sb, buf);
+	si_read_unlock(sb);
+
+	if (!err) {
+		buf->f_type = AUFS_SUPER_MAGIC;
+		buf->f_namelen = AUFS_MAX_NAMELEN;
+		memset(&buf->f_fsid, 0, sizeof(buf->f_fsid));
+	}
+	/* buf->f_bsize = buf->f_blocks = buf->f_bfree = buf->f_bavail = -1; */
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int aufs_sync_fs(struct super_block *sb, int wait)
+{
+	int err, e;
+	aufs_bindex_t bbot, bindex;
+	struct au_branch *br;
+	struct super_block *h_sb;
+
+	err = 0;
+	si_noflush_read_lock(sb);
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (!au_br_writable(br->br_perm))
+			continue;
+
+		h_sb = au_sbr_sb(sb, bindex);
+		e = vfsub_sync_filesystem(h_sb, wait);
+		if (unlikely(e && !err))
+			err = e;
+		/* go on even if an error happens */
+	}
+	si_read_unlock(sb);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* final actions when unmounting a file system */
+static void aufs_put_super(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+
+	sbinfo = au_sbi(sb);
+	if (sbinfo)
+		kobject_put(&sbinfo->si_kobj);
+}
+
+/* ---------------------------------------------------------------------- */
+
+void *au_array_alloc(unsigned long long *hint, au_arraycb_t cb,
+		     struct super_block *sb, void *arg)
+{
+	void *array;
+	unsigned long long n, sz;
+
+	array = NULL;
+	n = 0;
+	if (!*hint)
+		goto out;
+
+	if (*hint > ULLONG_MAX / sizeof(array)) {
+		array = ERR_PTR(-EMFILE);
+		pr_err("hint %llu\n", *hint);
+		goto out;
+	}
+
+	sz = sizeof(array) * *hint;
+	array = kzalloc(sz, GFP_NOFS);
+	if (unlikely(!array))
+		array = vzalloc(sz);
+	if (unlikely(!array)) {
+		array = ERR_PTR(-ENOMEM);
+		goto out;
+	}
+
+	n = cb(sb, array, *hint, arg);
+	AuDebugOn(n > *hint);
+
+out:
+	*hint = n;
+	return array;
+}
+
+static unsigned long long au_iarray_cb(struct super_block *sb, void *a,
+				       unsigned long long max __maybe_unused,
+				       void *arg)
+{
+	unsigned long long n;
+	struct inode **p, *inode;
+	struct list_head *head;
+
+	n = 0;
+	p = a;
+	head = arg;
+	spin_lock(&sb->s_inode_list_lock);
+	list_for_each_entry(inode, head, i_sb_list) {
+		if (!au_is_bad_inode(inode)
+		    && au_ii(inode)->ii_btop >= 0) {
+			spin_lock(&inode->i_lock);
+			if (atomic_read(&inode->i_count)) {
+				au_igrab(inode);
+				*p++ = inode;
+				n++;
+				AuDebugOn(n > max);
+			}
+			spin_unlock(&inode->i_lock);
+		}
+	}
+	spin_unlock(&sb->s_inode_list_lock);
+
+	return n;
+}
+
+struct inode **au_iarray_alloc(struct super_block *sb, unsigned long long *max)
+{
+	struct au_sbinfo *sbi;
+
+	sbi = au_sbi(sb);
+	*max = au_lcnt_read(&sbi->si_ninodes, /*do_rev*/1);
+	return au_array_alloc(max, au_iarray_cb, sb, &sb->s_inodes);
+}
+
+void au_iarray_free(struct inode **a, unsigned long long max)
+{
+	unsigned long long ull;
+
+	for (ull = 0; ull < max; ull++)
+		iput(a[ull]);
+	kvfree(a);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * refresh dentry and inode at remount time.
+ */
+/* todo: consolidate with simple_reval_dpath() and au_reval_for_attr() */
+static int au_do_refresh(struct dentry *dentry, unsigned int dir_flags,
+		      struct dentry *parent)
+{
+	int err;
+
+	di_write_lock_child(dentry);
+	di_read_lock_parent(parent, AuLock_IR);
+	err = au_refresh_dentry(dentry, parent);
+	if (!err && dir_flags)
+		au_hn_reset(d_inode(dentry), dir_flags);
+	di_read_unlock(parent, AuLock_IR);
+	di_write_unlock(dentry);
+
+	return err;
+}
+
+static int au_do_refresh_d(struct dentry *dentry, unsigned int sigen,
+			   struct au_sbinfo *sbinfo,
+			   const unsigned int dir_flags, unsigned int do_idop)
+{
+	int err;
+	struct dentry *parent;
+
+	err = 0;
+	parent = dget_parent(dentry);
+	if (!au_digen_test(parent, sigen) && au_digen_test(dentry, sigen)) {
+		if (d_really_is_positive(dentry)) {
+			if (!d_is_dir(dentry))
+				err = au_do_refresh(dentry, /*dir_flags*/0,
+						 parent);
+			else {
+				err = au_do_refresh(dentry, dir_flags, parent);
+				if (unlikely(err))
+					au_fset_si(sbinfo, FAILED_REFRESH_DIR);
+			}
+		} else
+			err = au_do_refresh(dentry, /*dir_flags*/0, parent);
+		AuDbgDentry(dentry);
+	}
+	dput(parent);
+
+	if (!err) {
+		if (do_idop)
+			au_refresh_dop(dentry, /*force_reval*/0);
+	} else
+		au_refresh_dop(dentry, /*force_reval*/1);
+
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_refresh_d(struct super_block *sb, unsigned int do_idop)
+{
+	int err, i, j, ndentry, e;
+	unsigned int sigen;
+	struct au_dcsub_pages dpages;
+	struct au_dpage *dpage;
+	struct dentry **dentries, *d;
+	struct au_sbinfo *sbinfo;
+	struct dentry *root = sb->s_root;
+	const unsigned int dir_flags = au_hi_flags(d_inode(root), /*isdir*/1);
+
+	if (do_idop)
+		au_refresh_dop(root, /*force_reval*/0);
+
+	err = au_dpages_init(&dpages, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+	err = au_dcsub_pages(&dpages, root, NULL, NULL);
+	if (unlikely(err))
+		goto out_dpages;
+
+	sigen = au_sigen(sb);
+	sbinfo = au_sbi(sb);
+	for (i = 0; i < dpages.ndpage; i++) {
+		dpage = dpages.dpages + i;
+		dentries = dpage->dentries;
+		ndentry = dpage->ndentry;
+		for (j = 0; j < ndentry; j++) {
+			d = dentries[j];
+			e = au_do_refresh_d(d, sigen, sbinfo, dir_flags,
+					    do_idop);
+			if (unlikely(e && !err))
+				err = e;
+			/* go on even err */
+		}
+	}
+
+out_dpages:
+	au_dpages_free(&dpages);
+out:
+	return err;
+}
+
+static int au_refresh_i(struct super_block *sb, unsigned int do_idop)
+{
+	int err, e;
+	unsigned int sigen;
+	unsigned long long max, ull;
+	struct inode *inode, **array;
+
+	array = au_iarray_alloc(sb, &max);
+	err = PTR_ERR(array);
+	if (IS_ERR(array))
+		goto out;
+
+	err = 0;
+	sigen = au_sigen(sb);
+	for (ull = 0; ull < max; ull++) {
+		inode = array[ull];
+		if (unlikely(!inode))
+			break;
+
+		e = 0;
+		ii_write_lock_child(inode);
+		if (au_iigen(inode, NULL) != sigen) {
+			e = au_refresh_hinode_self(inode);
+			if (unlikely(e)) {
+				au_refresh_iop(inode, /*force_getattr*/1);
+				pr_err("error %d, i%lu\n", e, inode->i_ino);
+				if (!err)
+					err = e;
+				/* go on even if err */
+			}
+		}
+		if (!e && do_idop)
+			au_refresh_iop(inode, /*force_getattr*/0);
+		ii_write_unlock(inode);
+	}
+
+	au_iarray_free(array, max);
+
+out:
+	return err;
+}
+
+static void au_remount_refresh(struct super_block *sb, unsigned int do_idop)
+{
+	int err, e;
+	unsigned int udba;
+	aufs_bindex_t bindex, bbot;
+	struct dentry *root;
+	struct inode *inode;
+	struct au_branch *br;
+	struct au_sbinfo *sbi;
+
+	au_sigen_inc(sb);
+	sbi = au_sbi(sb);
+	au_fclr_si(sbi, FAILED_REFRESH_DIR);
+
+	root = sb->s_root;
+	DiMustNoWaiters(root);
+	inode = d_inode(root);
+	IiMustNoWaiters(inode);
+
+	udba = au_opt_udba(sb);
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		err = au_hnotify_reset_br(udba, br, br->br_perm);
+		if (unlikely(err))
+			AuIOErr("hnotify failed on br %d, %d, ignored\n",
+				bindex, err);
+		/* go on even if err */
+	}
+	au_hn_reset(inode, au_hi_flags(inode, /*isdir*/1));
+
+	if (do_idop) {
+		if (au_ftest_si(sbi, NO_DREVAL)) {
+			AuDebugOn(sb->s_d_op == &aufs_dop_noreval);
+			sb->s_d_op = &aufs_dop_noreval;
+			AuDebugOn(sbi->si_iop_array == aufs_iop_nogetattr);
+			sbi->si_iop_array = aufs_iop_nogetattr;
+		} else {
+			AuDebugOn(sb->s_d_op == &aufs_dop);
+			sb->s_d_op = &aufs_dop;
+			AuDebugOn(sbi->si_iop_array == aufs_iop);
+			sbi->si_iop_array = aufs_iop;
+		}
+		pr_info("reset to %ps and %ps\n",
+			sb->s_d_op, sbi->si_iop_array);
+	}
+
+	di_write_unlock(root);
+	err = au_refresh_d(sb, do_idop);
+	e = au_refresh_i(sb, do_idop);
+	if (unlikely(e && !err))
+		err = e;
+	/* aufs_write_lock() calls ..._child() */
+	di_write_lock_child(root);
+
+	au_cpup_attr_all(inode, /*force*/1);
+
+	if (unlikely(err))
+		AuIOErr("refresh failed, ignored, %d\n", err);
+}
+
+/* stop extra interpretation of errno in mount(8), and strange error messages */
+static int cvt_err(int err)
+{
+	AuTraceErr(err);
+
+	switch (err) {
+	case -ENOENT:
+	case -ENOTDIR:
+	case -EEXIST:
+	case -EIO:
+		err = -EINVAL;
+	}
+	return err;
+}
+
+static int aufs_remount_fs(struct super_block *sb, int *flags, char *data)
+{
+	int err, do_dx;
+	unsigned int mntflags;
+	struct au_opts opts = {
+		.opt = NULL
+	};
+	struct dentry *root;
+	struct inode *inode;
+	struct au_sbinfo *sbinfo;
+
+	err = 0;
+	root = sb->s_root;
+	if (!data || !*data) {
+		err = si_write_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+		if (!err) {
+			di_write_lock_child(root);
+			err = au_opts_verify(sb, *flags, /*pending*/0);
+			aufs_write_unlock(root);
+		}
+		goto out;
+	}
+
+	err = -ENOMEM;
+	opts.opt = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!opts.opt))
+		goto out;
+	opts.max_opt = PAGE_SIZE / sizeof(*opts.opt);
+	opts.flags = AuOpts_REMOUNT;
+	opts.sb_flags = *flags;
+
+	/* parse it before aufs lock */
+	err = au_opts_parse(sb, data, &opts);
+	if (unlikely(err))
+		goto out_opts;
+
+	sbinfo = au_sbi(sb);
+	inode = d_inode(root);
+	inode_lock(inode);
+	err = si_write_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+	if (unlikely(err))
+		goto out_mtx;
+	di_write_lock_child(root);
+
+	/* au_opts_remount() may return an error */
+	err = au_opts_remount(sb, &opts);
+	au_opts_free(&opts);
+
+	if (au_ftest_opts(opts.flags, REFRESH))
+		au_remount_refresh(sb, au_ftest_opts(opts.flags, REFRESH_IDOP));
+
+	if (au_ftest_opts(opts.flags, REFRESH_DYAOP)) {
+		mntflags = au_mntflags(sb);
+		do_dx = !!au_opt_test(mntflags, DIO);
+		au_dy_arefresh(do_dx);
+	}
+
+	au_fhsm_wrote_all(sb, /*force*/1); /* ?? */
+	aufs_write_unlock(root);
+
+out_mtx:
+	inode_unlock(inode);
+out_opts:
+	free_page((unsigned long)opts.opt);
+out:
+	err = cvt_err(err);
+	AuTraceErr(err);
+	return err;
+}
+
+static const struct super_operations aufs_sop = {
+	.alloc_inode	= aufs_alloc_inode,
+	.destroy_inode	= aufs_destroy_inode,
+	.free_inode	= aufs_free_inode,
+	/* always deleting, no clearing */
+	.drop_inode	= generic_delete_inode,
+	.show_options	= aufs_show_options,
+	.statfs		= aufs_statfs,
+	.put_super	= aufs_put_super,
+	.sync_fs	= aufs_sync_fs,
+	.remount_fs	= aufs_remount_fs,
+#ifdef CONFIG_AUFS_BDEV_LOOP
+	.real_loop	= aufs_real_loop
+#endif
+};
+
+/* ---------------------------------------------------------------------- */
+
+static int alloc_root(struct super_block *sb)
+{
+	int err;
+	struct inode *inode;
+	struct dentry *root;
+
+	err = -ENOMEM;
+	inode = au_iget_locked(sb, AUFS_ROOT_INO);
+	err = PTR_ERR(inode);
+	if (IS_ERR(inode))
+		goto out;
+
+	inode->i_op = aufs_iop + AuIop_DIR; /* with getattr by default */
+	inode->i_fop = &aufs_dir_fop;
+	inode->i_mode = S_IFDIR;
+	set_nlink(inode, 2);
+	unlock_new_inode(inode);
+
+	root = d_make_root(inode);
+	if (unlikely(!root))
+		goto out;
+	err = PTR_ERR(root);
+	if (IS_ERR(root))
+		goto out;
+
+	err = au_di_init(root);
+	if (!err) {
+		sb->s_root = root;
+		return 0; /* success */
+	}
+	dput(root);
+
+out:
+	return err;
+}
+
+static int aufs_fill_super(struct super_block *sb, void *raw_data,
+			   int silent __maybe_unused)
+{
+	int err;
+	struct au_opts opts = {
+		.opt = NULL
+	};
+	struct au_sbinfo *sbinfo;
+	struct dentry *root;
+	struct inode *inode;
+	char *arg = raw_data;
+
+	if (unlikely(!arg || !*arg)) {
+		err = -EINVAL;
+		pr_err("no arg\n");
+		goto out;
+	}
+
+	err = -ENOMEM;
+	opts.opt = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!opts.opt))
+		goto out;
+	opts.max_opt = PAGE_SIZE / sizeof(*opts.opt);
+	opts.sb_flags = sb->s_flags;
+
+	err = au_si_alloc(sb);
+	if (unlikely(err))
+		goto out_opts;
+	sbinfo = au_sbi(sb);
+
+	/* all timestamps always follow the ones on the branch */
+	sb->s_flags |= SB_NOATIME | SB_NODIRATIME;
+	sb->s_flags |= SB_I_VERSION; /* do we really need this? */
+	sb->s_op = &aufs_sop;
+	sb->s_d_op = &aufs_dop;
+	sb->s_magic = AUFS_SUPER_MAGIC;
+	sb->s_maxbytes = 0;
+	sb->s_stack_depth = 1;
+	au_export_init(sb);
+	au_xattr_init(sb);
+
+	err = alloc_root(sb);
+	if (unlikely(err)) {
+		si_write_unlock(sb);
+		goto out_info;
+	}
+	root = sb->s_root;
+	inode = d_inode(root);
+
+	/*
+	 * actually we can parse options regardless aufs lock here.
+	 * but at remount time, parsing must be done before aufs lock.
+	 * so we follow the same rule.
+	 */
+	ii_write_lock_parent(inode);
+	aufs_write_unlock(root);
+	err = au_opts_parse(sb, arg, &opts);
+	if (unlikely(err))
+		goto out_root;
+
+	/* lock vfs_inode first, then aufs. */
+	inode_lock(inode);
+	aufs_write_lock(root);
+	err = au_opts_mount(sb, &opts);
+	au_opts_free(&opts);
+	if (!err && au_ftest_si(sbinfo, NO_DREVAL)) {
+		sb->s_d_op = &aufs_dop_noreval;
+		pr_info("%ps\n", sb->s_d_op);
+		au_refresh_dop(root, /*force_reval*/0);
+		sbinfo->si_iop_array = aufs_iop_nogetattr;
+		au_refresh_iop(inode, /*force_getattr*/0);
+	}
+	aufs_write_unlock(root);
+	inode_unlock(inode);
+	if (!err)
+		goto out_opts; /* success */
+
+out_root:
+	dput(root);
+	sb->s_root = NULL;
+out_info:
+	kobject_put(&sbinfo->si_kobj);
+	sb->s_fs_info = NULL;
+out_opts:
+	free_page((unsigned long)opts.opt);
+out:
+	AuTraceErr(err);
+	err = cvt_err(err);
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct dentry *aufs_mount(struct file_system_type *fs_type, int flags,
+				 const char *dev_name __maybe_unused,
+				 void *raw_data)
+{
+	struct dentry *root;
+
+	/* all timestamps always follow the ones on the branch */
+	/* mnt->mnt_flags |= MNT_NOATIME | MNT_NODIRATIME; */
+	root = mount_nodev(fs_type, flags, raw_data, aufs_fill_super);
+	if (IS_ERR(root))
+		goto out;
+
+	au_sbilist_add(root->d_sb);
+
+out:
+	return root;
+}
+
+static void aufs_kill_sb(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+
+	sbinfo = au_sbi(sb);
+	if (sbinfo) {
+		au_sbilist_del(sb);
+		aufs_write_lock(sb->s_root);
+		au_fhsm_fin(sb);
+		if (sbinfo->si_wbr_create_ops->fin)
+			sbinfo->si_wbr_create_ops->fin(sb);
+		if (au_opt_test(sbinfo->si_mntflags, UDBA_HNOTIFY)) {
+			au_opt_set_udba(sbinfo->si_mntflags, UDBA_NONE);
+			au_remount_refresh(sb, /*do_idop*/0);
+		}
+		if (au_opt_test(sbinfo->si_mntflags, PLINK))
+			au_plink_put(sb, /*verbose*/1);
+		au_xino_clr(sb);
+		au_dr_opt_flush(sb);
+		sbinfo->si_sb = NULL;
+		aufs_write_unlock(sb->s_root);
+		au_nwt_flush(&sbinfo->si_nowait);
+	}
+	kill_anon_super(sb);
+}
+
+struct file_system_type aufs_fs_type = {
+	.name		= AUFS_FSTYPE,
+	/* a race between rename and others */
+	.fs_flags	= FS_RENAME_DOES_D_MOVE
+				/* untested */
+				/*| FS_ALLOW_IDMAP*/
+				,
+	.mount		= aufs_mount,
+	.kill_sb	= aufs_kill_sb,
+	/* no need to __module_get() and module_put(). */
+	.owner		= THIS_MODULE,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/super.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/super.h
@@ -0,0 +1,587 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * super_block operations
+ */
+
+#ifndef __AUFS_SUPER_H__
+#define __AUFS_SUPER_H__
+
+#ifdef __KERNEL__
+
+#include <linux/fs.h>
+#include <linux/kobject.h>
+#include "hbl.h"
+#include "lcnt.h"
+#include "rwsem.h"
+#include "wkq.h"
+
+/* policies to select one among multiple writable branches */
+struct au_wbr_copyup_operations {
+	int (*copyup)(struct dentry *dentry);
+};
+
+#define AuWbr_DIR	1		/* target is a dir */
+#define AuWbr_PARENT	(1 << 1)	/* always require a parent */
+
+#define au_ftest_wbr(flags, name)	((flags) & AuWbr_##name)
+#define au_fset_wbr(flags, name)	{ (flags) |= AuWbr_##name; }
+#define au_fclr_wbr(flags, name)	{ (flags) &= ~AuWbr_##name; }
+
+struct au_wbr_create_operations {
+	int (*create)(struct dentry *dentry, unsigned int flags);
+	int (*init)(struct super_block *sb);
+	int (*fin)(struct super_block *sb);
+};
+
+struct au_wbr_mfs {
+	struct mutex	mfs_lock; /* protect this structure */
+	unsigned long	mfs_jiffy;
+	unsigned long	mfs_expire;
+	aufs_bindex_t	mfs_bindex;
+
+	unsigned long long	mfsrr_bytes;
+	unsigned long long	mfsrr_watermark;
+};
+
+#define AuPlink_NHASH 100
+static inline int au_plink_hash(ino_t ino)
+{
+	return ino % AuPlink_NHASH;
+}
+
+/* File-based Hierarchical Storage Management */
+struct au_fhsm {
+#ifdef CONFIG_AUFS_FHSM
+	/* allow only one process who can receive the notification */
+	spinlock_t		fhsm_spin;
+	pid_t			fhsm_pid;
+	wait_queue_head_t	fhsm_wqh;
+	atomic_t		fhsm_readable;
+
+	/* these are protected by si_rwsem */
+	unsigned long		fhsm_expire;
+	aufs_bindex_t		fhsm_bottom;
+#endif
+};
+
+struct au_branch;
+struct au_sbinfo {
+	/* nowait tasks in the system-wide workqueue */
+	struct au_nowait_tasks	si_nowait;
+
+	/*
+	 * tried sb->s_umount, but failed due to the dependency between i_mutex.
+	 * rwsem for au_sbinfo is necessary.
+	 */
+	struct au_rwsem		si_rwsem;
+
+	/*
+	 * dirty approach to protect sb->sb_inodes and ->s_files (gone) from
+	 * remount.
+	 */
+	au_lcnt_t		si_ninodes, si_nfiles;
+
+	/* branch management */
+	unsigned int		si_generation;
+
+	/* see AuSi_ flags */
+	unsigned char		au_si_status;
+
+	aufs_bindex_t		si_bbot;
+
+	/* dirty trick to keep br_id plus */
+	unsigned int		si_last_br_id :
+				sizeof(aufs_bindex_t) * BITS_PER_BYTE - 1;
+	struct au_branch	**si_branch;
+
+	/* policy to select a writable branch */
+	unsigned char		si_wbr_copyup;
+	unsigned char		si_wbr_create;
+	struct au_wbr_copyup_operations *si_wbr_copyup_ops;
+	struct au_wbr_create_operations *si_wbr_create_ops;
+
+	/* round robin */
+	atomic_t		si_wbr_rr_next;
+
+	/* most free space */
+	struct au_wbr_mfs	si_wbr_mfs;
+
+	/* File-based Hierarchical Storage Management */
+	struct au_fhsm		si_fhsm;
+
+	/* mount flags */
+	/* include/asm-ia64/siginfo.h defines a macro named si_flags */
+	unsigned int		si_mntflags;
+
+	/* external inode number (bitmap and translation table) */
+	loff_t			si_ximaxent;	/* max entries in a xino */
+
+	struct file		*si_xib;
+	struct mutex		si_xib_mtx; /* protect xib members */
+	unsigned long		*si_xib_buf;
+	unsigned long		si_xib_last_pindex;
+	int			si_xib_next_bit;
+
+	unsigned long		si_xino_jiffy;
+	unsigned long		si_xino_expire;
+	/* reserved for future use */
+	/* unsigned long long	si_xib_limit; */	/* Max xib file size */
+
+#ifdef CONFIG_AUFS_EXPORT
+	/* i_generation */
+	/* todo: make xigen file an array to support many inode numbers */
+	struct file		*si_xigen;
+	atomic_t		si_xigen_next;
+#endif
+
+	/* dirty trick to support atomic_open */
+	struct hlist_bl_head	si_aopen;
+
+	/* vdir parameters */
+	unsigned long		si_rdcache;	/* max cache time in jiffies */
+	unsigned int		si_rdblk;	/* deblk size */
+	unsigned int		si_rdhash;	/* hash size */
+
+	/*
+	 * If the number of whiteouts are larger than si_dirwh, leave all of
+	 * them after au_whtmp_ren to reduce the cost of rmdir(2).
+	 * future fsck.aufs or kernel thread will remove them later.
+	 * Otherwise, remove all whiteouts and the dir in rmdir(2).
+	 */
+	unsigned int		si_dirwh;
+
+	/* pseudo_link list */
+	struct hlist_bl_head	si_plink[AuPlink_NHASH];
+	wait_queue_head_t	si_plink_wq;
+	spinlock_t		si_plink_maint_lock;
+	pid_t			si_plink_maint_pid;
+
+	/* file list */
+	struct hlist_bl_head	si_files;
+
+	/* with/without getattr, brother of sb->s_d_op */
+	const struct inode_operations *si_iop_array;
+
+	/*
+	 * sysfs and lifetime management.
+	 * this is not a small structure and it may be a waste of memory in case
+	 * of sysfs is disabled, particularly when many aufs-es are mounted.
+	 * but using sysfs is majority.
+	 */
+	struct kobject		si_kobj;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry		 *si_dbgaufs;
+	struct dentry		 *si_dbgaufs_plink;
+	struct dentry		 *si_dbgaufs_xib;
+#ifdef CONFIG_AUFS_EXPORT
+	struct dentry		 *si_dbgaufs_xigen;
+#endif
+#endif
+
+#ifdef CONFIG_AUFS_SBILIST
+	struct hlist_bl_node	si_list;
+#endif
+
+	/* dirty, necessary for unmounting, sysfs and sysrq */
+	struct super_block	*si_sb;
+};
+
+/* sbinfo status flags */
+/*
+ * set true when refresh_dirs() failed at remount time.
+ * then try refreshing dirs at access time again.
+ * if it is false, refreshing dirs at access time is unnecessary
+ */
+#define AuSi_FAILED_REFRESH_DIR	1
+#define AuSi_FHSM		(1 << 1)	/* fhsm is active now */
+#define AuSi_NO_DREVAL		(1 << 2)	/* disable all d_revalidate */
+
+#ifndef CONFIG_AUFS_FHSM
+#undef AuSi_FHSM
+#define AuSi_FHSM		0
+#endif
+
+static inline unsigned char au_do_ftest_si(struct au_sbinfo *sbi,
+					   unsigned int flag)
+{
+	AuRwMustAnyLock(&sbi->si_rwsem);
+	return sbi->au_si_status & flag;
+}
+#define au_ftest_si(sbinfo, name)	au_do_ftest_si(sbinfo, AuSi_##name)
+#define au_fset_si(sbinfo, name) do { \
+	AuRwMustWriteLock(&(sbinfo)->si_rwsem); \
+	(sbinfo)->au_si_status |= AuSi_##name; \
+} while (0)
+#define au_fclr_si(sbinfo, name) do { \
+	AuRwMustWriteLock(&(sbinfo)->si_rwsem); \
+	(sbinfo)->au_si_status &= ~AuSi_##name; \
+} while (0)
+
+/* ---------------------------------------------------------------------- */
+
+/* policy to select one among writable branches */
+#define AuWbrCopyup(sbinfo, ...) \
+	((sbinfo)->si_wbr_copyup_ops->copyup(__VA_ARGS__))
+#define AuWbrCreate(sbinfo, ...) \
+	((sbinfo)->si_wbr_create_ops->create(__VA_ARGS__))
+
+/* flags for si_read_lock()/aufs_read_lock()/di_read_lock() */
+#define AuLock_DW		1		/* write-lock dentry */
+#define AuLock_IR		(1 << 1)	/* read-lock inode */
+#define AuLock_IW		(1 << 2)	/* write-lock inode */
+#define AuLock_FLUSH		(1 << 3)	/* wait for 'nowait' tasks */
+#define AuLock_DIRS		(1 << 4)	/* target is a pair of dirs */
+						/* except RENAME_EXCHANGE */
+#define AuLock_NOPLM		(1 << 5)	/* return err in plm mode */
+#define AuLock_NOPLMW		(1 << 6)	/* wait for plm mode ends */
+#define AuLock_GEN		(1 << 7)	/* test digen/iigen */
+#define au_ftest_lock(flags, name)	((flags) & AuLock_##name)
+#define au_fset_lock(flags, name) \
+	do { (flags) |= AuLock_##name; } while (0)
+#define au_fclr_lock(flags, name) \
+	do { (flags) &= ~AuLock_##name; } while (0)
+
+/* ---------------------------------------------------------------------- */
+
+/* super.c */
+extern struct file_system_type aufs_fs_type;
+struct inode *au_iget_locked(struct super_block *sb, ino_t ino);
+typedef unsigned long long (*au_arraycb_t)(struct super_block *sb, void *array,
+					   unsigned long long max, void *arg);
+void *au_array_alloc(unsigned long long *hint, au_arraycb_t cb,
+		     struct super_block *sb, void *arg);
+struct inode **au_iarray_alloc(struct super_block *sb, unsigned long long *max);
+void au_iarray_free(struct inode **a, unsigned long long max);
+
+/* sbinfo.c */
+void au_si_free(struct kobject *kobj);
+int au_si_alloc(struct super_block *sb);
+int au_sbr_realloc(struct au_sbinfo *sbinfo, int nbr, int may_shrink);
+
+unsigned int au_sigen_inc(struct super_block *sb);
+aufs_bindex_t au_new_br_id(struct super_block *sb);
+
+int si_read_lock(struct super_block *sb, int flags);
+int si_write_lock(struct super_block *sb, int flags);
+int aufs_read_lock(struct dentry *dentry, int flags);
+void aufs_read_unlock(struct dentry *dentry, int flags);
+void aufs_write_lock(struct dentry *dentry);
+void aufs_write_unlock(struct dentry *dentry);
+int aufs_read_and_write_lock2(struct dentry *d1, struct dentry *d2, int flags);
+void aufs_read_and_write_unlock2(struct dentry *d1, struct dentry *d2);
+
+/* wbr_policy.c */
+extern struct au_wbr_copyup_operations au_wbr_copyup_ops[];
+extern struct au_wbr_create_operations au_wbr_create_ops[];
+int au_cpdown_dirs(struct dentry *dentry, aufs_bindex_t bdst);
+int au_wbr_nonopq(struct dentry *dentry, aufs_bindex_t bindex);
+int au_wbr_do_copyup_bu(struct dentry *dentry, aufs_bindex_t btop);
+
+/* mvdown.c */
+int au_mvdown(struct dentry *dentry, struct aufs_mvdown __user *arg);
+
+#ifdef CONFIG_AUFS_FHSM
+/* fhsm.c */
+
+static inline pid_t au_fhsm_pid(struct au_fhsm *fhsm)
+{
+	pid_t pid;
+
+	spin_lock(&fhsm->fhsm_spin);
+	pid = fhsm->fhsm_pid;
+	spin_unlock(&fhsm->fhsm_spin);
+
+	return pid;
+}
+
+void au_fhsm_wrote(struct super_block *sb, aufs_bindex_t bindex, int force);
+void au_fhsm_wrote_all(struct super_block *sb, int force);
+int au_fhsm_fd(struct super_block *sb, int oflags);
+int au_fhsm_br_alloc(struct au_branch *br);
+void au_fhsm_set_bottom(struct super_block *sb, aufs_bindex_t bindex);
+void au_fhsm_fin(struct super_block *sb);
+void au_fhsm_init(struct au_sbinfo *sbinfo);
+void au_fhsm_set(struct au_sbinfo *sbinfo, unsigned int sec);
+void au_fhsm_show(struct seq_file *seq, struct au_sbinfo *sbinfo);
+#else
+AuStubVoid(au_fhsm_wrote, struct super_block *sb, aufs_bindex_t bindex,
+	   int force)
+AuStubVoid(au_fhsm_wrote_all, struct super_block *sb, int force)
+AuStub(int, au_fhsm_fd, return -EOPNOTSUPP, struct super_block *sb, int oflags)
+AuStub(pid_t, au_fhsm_pid, return 0, struct au_fhsm *fhsm)
+AuStubInt0(au_fhsm_br_alloc, struct au_branch *br)
+AuStubVoid(au_fhsm_set_bottom, struct super_block *sb, aufs_bindex_t bindex)
+AuStubVoid(au_fhsm_fin, struct super_block *sb)
+AuStubVoid(au_fhsm_init, struct au_sbinfo *sbinfo)
+AuStubVoid(au_fhsm_set, struct au_sbinfo *sbinfo, unsigned int sec)
+AuStubVoid(au_fhsm_show, struct seq_file *seq, struct au_sbinfo *sbinfo)
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct au_sbinfo *au_sbi(struct super_block *sb)
+{
+	return sb->s_fs_info;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_EXPORT
+int au_test_nfsd(void);
+void au_export_init(struct super_block *sb);
+void au_xigen_inc(struct inode *inode);
+int au_xigen_new(struct inode *inode);
+int au_xigen_set(struct super_block *sb, struct path *path);
+void au_xigen_clr(struct super_block *sb);
+
+static inline int au_busy_or_stale(void)
+{
+	if (!au_test_nfsd())
+		return -EBUSY;
+	return -ESTALE;
+}
+#else
+AuStubInt0(au_test_nfsd, void)
+AuStubVoid(au_export_init, struct super_block *sb)
+AuStubVoid(au_xigen_inc, struct inode *inode)
+AuStubInt0(au_xigen_new, struct inode *inode)
+AuStubInt0(au_xigen_set, struct super_block *sb, struct path *path)
+AuStubVoid(au_xigen_clr, struct super_block *sb)
+AuStub(int, au_busy_or_stale, return -EBUSY, void)
+#endif /* CONFIG_AUFS_EXPORT */
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef CONFIG_AUFS_SBILIST
+/* module.c */
+extern struct hlist_bl_head au_sbilist;
+
+static inline void au_sbilist_init(void)
+{
+	INIT_HLIST_BL_HEAD(&au_sbilist);
+}
+
+static inline void au_sbilist_add(struct super_block *sb)
+{
+	au_hbl_add(&au_sbi(sb)->si_list, &au_sbilist);
+}
+
+static inline void au_sbilist_del(struct super_block *sb)
+{
+	au_hbl_del(&au_sbi(sb)->si_list, &au_sbilist);
+}
+
+#ifdef CONFIG_AUFS_MAGIC_SYSRQ
+static inline void au_sbilist_lock(void)
+{
+	hlist_bl_lock(&au_sbilist);
+}
+
+static inline void au_sbilist_unlock(void)
+{
+	hlist_bl_unlock(&au_sbilist);
+}
+#define AuGFP_SBILIST	GFP_ATOMIC
+#else
+AuStubVoid(au_sbilist_lock, void)
+AuStubVoid(au_sbilist_unlock, void)
+#define AuGFP_SBILIST	GFP_NOFS
+#endif /* CONFIG_AUFS_MAGIC_SYSRQ */
+#else
+AuStubVoid(au_sbilist_init, void)
+AuStubVoid(au_sbilist_add, struct super_block *sb)
+AuStubVoid(au_sbilist_del, struct super_block *sb)
+AuStubVoid(au_sbilist_lock, void)
+AuStubVoid(au_sbilist_unlock, void)
+#define AuGFP_SBILIST	GFP_NOFS
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+static inline void dbgaufs_si_null(struct au_sbinfo *sbinfo)
+{
+	/*
+	 * This function is a dynamic '__init' function actually,
+	 * so the tiny check for si_rwsem is unnecessary.
+	 */
+	/* AuRwMustWriteLock(&sbinfo->si_rwsem); */
+#ifdef CONFIG_DEBUG_FS
+	sbinfo->si_dbgaufs = NULL;
+	sbinfo->si_dbgaufs_plink = NULL;
+	sbinfo->si_dbgaufs_xib = NULL;
+#ifdef CONFIG_AUFS_EXPORT
+	sbinfo->si_dbgaufs_xigen = NULL;
+#endif
+#endif
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* current->atomic_flags */
+/* this value should never corrupt the ones defined in linux/sched.h */
+#define PFA_AUFS	0x10
+
+TASK_PFA_TEST(AUFS, test_aufs)	/* task_test_aufs */
+TASK_PFA_SET(AUFS, aufs)	/* task_set_aufs */
+TASK_PFA_CLEAR(AUFS, aufs)	/* task_clear_aufs */
+
+static inline int si_pid_test(struct super_block *sb)
+{
+	return !!task_test_aufs(current);
+}
+
+static inline void si_pid_clr(struct super_block *sb)
+{
+	AuDebugOn(!task_test_aufs(current));
+	task_clear_aufs(current);
+}
+
+static inline void si_pid_set(struct super_block *sb)
+{
+	AuDebugOn(task_test_aufs(current));
+	task_set_aufs(current);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* lock superblock. mainly for entry point functions */
+#define __si_read_lock(sb)	au_rw_read_lock(&au_sbi(sb)->si_rwsem)
+#define __si_write_lock(sb)	au_rw_write_lock(&au_sbi(sb)->si_rwsem)
+#define __si_read_trylock(sb)	au_rw_read_trylock(&au_sbi(sb)->si_rwsem)
+#define __si_write_trylock(sb)	au_rw_write_trylock(&au_sbi(sb)->si_rwsem)
+/*
+#define __si_read_trylock_nested(sb) \
+	au_rw_read_trylock_nested(&au_sbi(sb)->si_rwsem)
+#define __si_write_trylock_nested(sb) \
+	au_rw_write_trylock_nested(&au_sbi(sb)->si_rwsem)
+*/
+
+#define __si_read_unlock(sb)	au_rw_read_unlock(&au_sbi(sb)->si_rwsem)
+#define __si_write_unlock(sb)	au_rw_write_unlock(&au_sbi(sb)->si_rwsem)
+#define __si_downgrade_lock(sb)	au_rw_dgrade_lock(&au_sbi(sb)->si_rwsem)
+
+#define SiMustNoWaiters(sb)	AuRwMustNoWaiters(&au_sbi(sb)->si_rwsem)
+#define SiMustAnyLock(sb)	AuRwMustAnyLock(&au_sbi(sb)->si_rwsem)
+#define SiMustWriteLock(sb)	AuRwMustWriteLock(&au_sbi(sb)->si_rwsem)
+
+static inline void si_noflush_read_lock(struct super_block *sb)
+{
+	__si_read_lock(sb);
+	si_pid_set(sb);
+}
+
+static inline int si_noflush_read_trylock(struct super_block *sb)
+{
+	int locked;
+
+	locked = __si_read_trylock(sb);
+	if (locked)
+		si_pid_set(sb);
+	return locked;
+}
+
+static inline void si_noflush_write_lock(struct super_block *sb)
+{
+	__si_write_lock(sb);
+	si_pid_set(sb);
+}
+
+static inline int si_noflush_write_trylock(struct super_block *sb)
+{
+	int locked;
+
+	locked = __si_write_trylock(sb);
+	if (locked)
+		si_pid_set(sb);
+	return locked;
+}
+
+#if 0 /* reserved */
+static inline int si_read_trylock(struct super_block *sb, int flags)
+{
+	if (au_ftest_lock(flags, FLUSH))
+		au_nwt_flush(&au_sbi(sb)->si_nowait);
+	return si_noflush_read_trylock(sb);
+}
+#endif
+
+static inline void si_read_unlock(struct super_block *sb)
+{
+	si_pid_clr(sb);
+	__si_read_unlock(sb);
+}
+
+#if 0 /* reserved */
+static inline int si_write_trylock(struct super_block *sb, int flags)
+{
+	if (au_ftest_lock(flags, FLUSH))
+		au_nwt_flush(&au_sbi(sb)->si_nowait);
+	return si_noflush_write_trylock(sb);
+}
+#endif
+
+static inline void si_write_unlock(struct super_block *sb)
+{
+	si_pid_clr(sb);
+	__si_write_unlock(sb);
+}
+
+#if 0 /* reserved */
+static inline void si_downgrade_lock(struct super_block *sb)
+{
+	__si_downgrade_lock(sb);
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+static inline aufs_bindex_t au_sbbot(struct super_block *sb)
+{
+	SiMustAnyLock(sb);
+	return au_sbi(sb)->si_bbot;
+}
+
+static inline unsigned int au_mntflags(struct super_block *sb)
+{
+	SiMustAnyLock(sb);
+	return au_sbi(sb)->si_mntflags;
+}
+
+static inline unsigned int au_sigen(struct super_block *sb)
+{
+	SiMustAnyLock(sb);
+	return au_sbi(sb)->si_generation;
+}
+
+static inline struct au_branch *au_sbr(struct super_block *sb,
+				       aufs_bindex_t bindex)
+{
+	SiMustAnyLock(sb);
+	return au_sbi(sb)->si_branch[0 + bindex];
+}
+
+static inline loff_t au_xi_maxent(struct super_block *sb)
+{
+	SiMustAnyLock(sb);
+	return au_sbi(sb)->si_ximaxent;
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_SUPER_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/sysaufs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/sysaufs.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sysfs interface and lifetime management
+ * they are necessary regardless sysfs is disabled.
+ */
+
+#include <linux/random.h>
+#include "aufs.h"
+
+unsigned long sysaufs_si_mask;
+struct kset *sysaufs_kset;
+
+#define AuSiAttr(_name) { \
+	.attr   = { .name = __stringify(_name), .mode = 0444 },	\
+	.show   = sysaufs_si_##_name,				\
+}
+
+static struct sysaufs_si_attr sysaufs_si_attr_xi_path = AuSiAttr(xi_path);
+struct attribute *sysaufs_si_attrs[] = {
+	&sysaufs_si_attr_xi_path.attr,
+	NULL,
+};
+
+static const struct sysfs_ops au_sbi_ops = {
+	.show   = sysaufs_si_show
+};
+
+static struct kobj_type au_sbi_ktype = {
+	.release	= au_si_free,
+	.sysfs_ops	= &au_sbi_ops,
+	.default_attrs	= sysaufs_si_attrs
+};
+
+/* ---------------------------------------------------------------------- */
+
+int sysaufs_si_init(struct au_sbinfo *sbinfo)
+{
+	int err;
+
+	sbinfo->si_kobj.kset = sysaufs_kset;
+	/* cf. sysaufs_name() */
+	err = kobject_init_and_add
+		(&sbinfo->si_kobj, &au_sbi_ktype, /*&sysaufs_kset->kobj*/NULL,
+		 SysaufsSiNamePrefix "%lx", sysaufs_si_id(sbinfo));
+
+	return err;
+}
+
+void sysaufs_fin(void)
+{
+	sysfs_remove_group(&sysaufs_kset->kobj, sysaufs_attr_group);
+	kset_unregister(sysaufs_kset);
+}
+
+int __init sysaufs_init(void)
+{
+	int err;
+
+	do {
+		get_random_bytes(&sysaufs_si_mask, sizeof(sysaufs_si_mask));
+	} while (!sysaufs_si_mask);
+
+	err = -EINVAL;
+	sysaufs_kset = kset_create_and_add(AUFS_NAME, NULL, fs_kobj);
+	if (unlikely(!sysaufs_kset))
+		goto out;
+	err = PTR_ERR(sysaufs_kset);
+	if (IS_ERR(sysaufs_kset))
+		goto out;
+	err = sysfs_create_group(&sysaufs_kset->kobj, sysaufs_attr_group);
+	if (unlikely(err))
+		kset_unregister(sysaufs_kset);
+
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/sysaufs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/sysaufs.h
@@ -0,0 +1,102 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sysfs interface and mount lifetime management
+ */
+
+#ifndef __SYSAUFS_H__
+#define __SYSAUFS_H__
+
+#ifdef __KERNEL__
+
+#include <linux/sysfs.h>
+#include "module.h"
+
+struct super_block;
+struct au_sbinfo;
+
+struct sysaufs_si_attr {
+	struct attribute attr;
+	int (*show)(struct seq_file *seq, struct super_block *sb);
+};
+
+/* ---------------------------------------------------------------------- */
+
+/* sysaufs.c */
+extern unsigned long sysaufs_si_mask;
+extern struct kset *sysaufs_kset;
+extern struct attribute *sysaufs_si_attrs[];
+int sysaufs_si_init(struct au_sbinfo *sbinfo);
+int __init sysaufs_init(void);
+void sysaufs_fin(void);
+
+/* ---------------------------------------------------------------------- */
+
+/* some people doesn't like to show a pointer in kernel */
+static inline unsigned long sysaufs_si_id(struct au_sbinfo *sbinfo)
+{
+	return sysaufs_si_mask ^ (unsigned long)sbinfo;
+}
+
+#define SysaufsSiNamePrefix	"si_"
+#define SysaufsSiNameLen	(sizeof(SysaufsSiNamePrefix) + 16)
+static inline void sysaufs_name(struct au_sbinfo *sbinfo, char *name)
+{
+	snprintf(name, SysaufsSiNameLen, SysaufsSiNamePrefix "%lx",
+		 sysaufs_si_id(sbinfo));
+}
+
+struct au_branch;
+#ifdef CONFIG_SYSFS
+/* sysfs.c */
+extern struct attribute_group *sysaufs_attr_group;
+
+int sysaufs_si_xi_path(struct seq_file *seq, struct super_block *sb);
+ssize_t sysaufs_si_show(struct kobject *kobj, struct attribute *attr,
+			 char *buf);
+long au_brinfo_ioctl(struct file *file, unsigned long arg);
+#ifdef CONFIG_COMPAT
+long au_brinfo_compat_ioctl(struct file *file, unsigned long arg);
+#endif
+
+void sysaufs_br_init(struct au_branch *br);
+void sysaufs_brs_add(struct super_block *sb, aufs_bindex_t bindex);
+void sysaufs_brs_del(struct super_block *sb, aufs_bindex_t bindex);
+
+#define sysaufs_brs_init()	do {} while (0)
+
+#else
+#define sysaufs_attr_group	NULL
+
+AuStubInt0(sysaufs_si_xi_path, struct seq_file *seq, struct super_block *sb)
+AuStub(ssize_t, sysaufs_si_show, return 0, struct kobject *kobj,
+       struct attribute *attr, char *buf)
+AuStubVoid(sysaufs_br_init, struct au_branch *br)
+AuStubVoid(sysaufs_brs_add, struct super_block *sb, aufs_bindex_t bindex)
+AuStubVoid(sysaufs_brs_del, struct super_block *sb, aufs_bindex_t bindex)
+
+static inline void sysaufs_brs_init(void)
+{
+	sysaufs_brs = 0;
+}
+
+#endif /* CONFIG_SYSFS */
+
+#endif /* __KERNEL__ */
+#endif /* __SYSAUFS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/sysfs.c
@@ -0,0 +1,374 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sysfs interface
+ */
+
+#include <linux/compat.h>
+#include <linux/seq_file.h>
+#include "aufs.h"
+
+#ifdef CONFIG_AUFS_FS_MODULE
+/* this entry violates the "one line per file" policy of sysfs */
+static ssize_t config_show(struct kobject *kobj, struct kobj_attribute *attr,
+			   char *buf)
+{
+	ssize_t err;
+	static char *conf =
+/* this file is generated at compiling */
+#include "conf.str"
+		;
+
+	err = snprintf(buf, PAGE_SIZE, conf);
+	if (unlikely(err >= PAGE_SIZE))
+		err = -EFBIG;
+	return err;
+}
+
+static struct kobj_attribute au_config_attr = __ATTR_RO(config);
+#endif
+
+static struct attribute *au_attr[] = {
+#ifdef CONFIG_AUFS_FS_MODULE
+	&au_config_attr.attr,
+#endif
+	NULL,	/* need to NULL terminate the list of attributes */
+};
+
+static struct attribute_group sysaufs_attr_group_body = {
+	.attrs = au_attr
+};
+
+struct attribute_group *sysaufs_attr_group = &sysaufs_attr_group_body;
+
+/* ---------------------------------------------------------------------- */
+
+int sysaufs_si_xi_path(struct seq_file *seq, struct super_block *sb)
+{
+	int err;
+
+	SiMustAnyLock(sb);
+
+	err = 0;
+	if (au_opt_test(au_mntflags(sb), XINO)) {
+		err = au_xino_path(seq, au_sbi(sb)->si_xib);
+		seq_putc(seq, '\n');
+	}
+	return err;
+}
+
+/*
+ * the lifetime of branch is independent from the entry under sysfs.
+ * sysfs handles the lifetime of the entry, and never call ->show() after it is
+ * unlinked.
+ */
+static int sysaufs_si_br(struct seq_file *seq, struct super_block *sb,
+			 aufs_bindex_t bindex, int idx)
+{
+	int err;
+	struct path path;
+	struct dentry *root;
+	struct au_branch *br;
+	au_br_perm_str_t perm;
+
+	AuDbg("b%d\n", bindex);
+
+	err = 0;
+	root = sb->s_root;
+	di_read_lock_parent(root, !AuLock_IR);
+	br = au_sbr(sb, bindex);
+
+	switch (idx) {
+	case AuBrSysfs_BR:
+		path.mnt = au_br_mnt(br);
+		path.dentry = au_h_dptr(root, bindex);
+		err = au_seq_path(seq, &path);
+		if (!err) {
+			au_optstr_br_perm(&perm, br->br_perm);
+			seq_printf(seq, "=%s\n", perm.a);
+		}
+		break;
+	case AuBrSysfs_BRID:
+		seq_printf(seq, "%d\n", br->br_id);
+		break;
+	}
+	di_read_unlock(root, !AuLock_IR);
+	if (unlikely(err || seq_has_overflowed(seq)))
+		err = -E2BIG;
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static struct seq_file *au_seq(char *p, ssize_t len)
+{
+	struct seq_file *seq;
+
+	seq = kzalloc(sizeof(*seq), GFP_NOFS);
+	if (seq) {
+		/* mutex_init(&seq.lock); */
+		seq->buf = p;
+		seq->size = len;
+		return seq; /* success */
+	}
+
+	seq = ERR_PTR(-ENOMEM);
+	return seq;
+}
+
+#define SysaufsBr_PREFIX	"br"
+#define SysaufsBrid_PREFIX	"brid"
+
+/* todo: file size may exceed PAGE_SIZE */
+ssize_t sysaufs_si_show(struct kobject *kobj, struct attribute *attr,
+			char *buf)
+{
+	ssize_t err;
+	int idx;
+	long l;
+	aufs_bindex_t bbot;
+	struct au_sbinfo *sbinfo;
+	struct super_block *sb;
+	struct seq_file *seq;
+	char *name;
+	struct attribute **cattr;
+
+	sbinfo = container_of(kobj, struct au_sbinfo, si_kobj);
+	sb = sbinfo->si_sb;
+
+	/*
+	 * prevent a race condition between sysfs and aufs.
+	 * for instance, sysfs_file_read() calls sysfs_get_active_two() which
+	 * prohibits maintaining the sysfs entries.
+	 * hew we acquire read lock after sysfs_get_active_two().
+	 * on the other hand, the remount process may maintain the sysfs/aufs
+	 * entries after acquiring write lock.
+	 * it can cause a deadlock.
+	 * simply we gave up processing read here.
+	 */
+	err = -EBUSY;
+	if (unlikely(!si_noflush_read_trylock(sb)))
+		goto out;
+
+	seq = au_seq(buf, PAGE_SIZE);
+	err = PTR_ERR(seq);
+	if (IS_ERR(seq))
+		goto out_unlock;
+
+	name = (void *)attr->name;
+	cattr = sysaufs_si_attrs;
+	while (*cattr) {
+		if (!strcmp(name, (*cattr)->name)) {
+			err = container_of(*cattr, struct sysaufs_si_attr, attr)
+				->show(seq, sb);
+			goto out_seq;
+		}
+		cattr++;
+	}
+
+	if (!strncmp(name, SysaufsBrid_PREFIX,
+		     sizeof(SysaufsBrid_PREFIX) - 1)) {
+		idx = AuBrSysfs_BRID;
+		name += sizeof(SysaufsBrid_PREFIX) - 1;
+	} else if (!strncmp(name, SysaufsBr_PREFIX,
+			    sizeof(SysaufsBr_PREFIX) - 1)) {
+		idx = AuBrSysfs_BR;
+		name += sizeof(SysaufsBr_PREFIX) - 1;
+	} else
+		  BUG();
+
+	err = kstrtol(name, 10, &l);
+	if (!err) {
+		bbot = au_sbbot(sb);
+		if (l <= bbot)
+			err = sysaufs_si_br(seq, sb, (aufs_bindex_t)l, idx);
+		else
+			err = -ENOENT;
+	}
+
+out_seq:
+	if (!err) {
+		err = seq->count;
+		/* sysfs limit */
+		if (unlikely(err == PAGE_SIZE))
+			err = -EFBIG;
+	}
+	au_kfree_rcu(seq);
+out_unlock:
+	si_read_unlock(sb);
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_brinfo(struct super_block *sb, union aufs_brinfo __user *arg)
+{
+	int err;
+	int16_t brid;
+	aufs_bindex_t bindex, bbot;
+	size_t sz;
+	char *buf;
+	struct seq_file *seq;
+	struct au_branch *br;
+
+	si_read_lock(sb, AuLock_FLUSH);
+	bbot = au_sbbot(sb);
+	err = bbot + 1;
+	if (!arg)
+		goto out;
+
+	err = -ENOMEM;
+	buf = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!buf))
+		goto out;
+
+	seq = au_seq(buf, PAGE_SIZE);
+	err = PTR_ERR(seq);
+	if (IS_ERR(seq))
+		goto out_buf;
+
+	sz = sizeof(*arg) - offsetof(union aufs_brinfo, path);
+	for (bindex = 0; bindex <= bbot; bindex++, arg++) {
+		/* VERIFY_WRITE */
+		err = !access_ok(arg, sizeof(*arg));
+		if (unlikely(err))
+			break;
+
+		br = au_sbr(sb, bindex);
+		brid = br->br_id;
+		BUILD_BUG_ON(sizeof(brid) != sizeof(arg->id));
+		err = __put_user(brid, &arg->id);
+		if (unlikely(err))
+			break;
+
+		BUILD_BUG_ON(sizeof(br->br_perm) != sizeof(arg->perm));
+		err = __put_user(br->br_perm, &arg->perm);
+		if (unlikely(err))
+			break;
+
+		err = au_seq_path(seq, &br->br_path);
+		if (unlikely(err))
+			break;
+		seq_putc(seq, '\0');
+		if (!seq_has_overflowed(seq)) {
+			err = copy_to_user(arg->path, seq->buf, seq->count);
+			seq->count = 0;
+			if (unlikely(err))
+				break;
+		} else {
+			err = -E2BIG;
+			goto out_seq;
+		}
+	}
+	if (unlikely(err))
+		err = -EFAULT;
+
+out_seq:
+	au_kfree_rcu(seq);
+out_buf:
+	free_page((unsigned long)buf);
+out:
+	si_read_unlock(sb);
+	return err;
+}
+
+long au_brinfo_ioctl(struct file *file, unsigned long arg)
+{
+	return au_brinfo(file->f_path.dentry->d_sb, (void __user *)arg);
+}
+
+#ifdef CONFIG_COMPAT
+long au_brinfo_compat_ioctl(struct file *file, unsigned long arg)
+{
+	return au_brinfo(file->f_path.dentry->d_sb, compat_ptr(arg));
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+void sysaufs_br_init(struct au_branch *br)
+{
+	int i;
+	struct au_brsysfs *br_sysfs;
+	struct attribute *attr;
+
+	br_sysfs = br->br_sysfs;
+	for (i = 0; i < ARRAY_SIZE(br->br_sysfs); i++) {
+		attr = &br_sysfs->attr;
+		sysfs_attr_init(attr);
+		attr->name = br_sysfs->name;
+		attr->mode = 0444;
+		br_sysfs++;
+	}
+}
+
+void sysaufs_brs_del(struct super_block *sb, aufs_bindex_t bindex)
+{
+	struct au_branch *br;
+	struct kobject *kobj;
+	struct au_brsysfs *br_sysfs;
+	int i;
+	aufs_bindex_t bbot;
+
+	if (!sysaufs_brs)
+		return;
+
+	kobj = &au_sbi(sb)->si_kobj;
+	bbot = au_sbbot(sb);
+	for (; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		br_sysfs = br->br_sysfs;
+		for (i = 0; i < ARRAY_SIZE(br->br_sysfs); i++) {
+			sysfs_remove_file(kobj, &br_sysfs->attr);
+			br_sysfs++;
+		}
+	}
+}
+
+void sysaufs_brs_add(struct super_block *sb, aufs_bindex_t bindex)
+{
+	int err, i;
+	aufs_bindex_t bbot;
+	struct kobject *kobj;
+	struct au_branch *br;
+	struct au_brsysfs *br_sysfs;
+
+	if (!sysaufs_brs)
+		return;
+
+	kobj = &au_sbi(sb)->si_kobj;
+	bbot = au_sbbot(sb);
+	for (; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		br_sysfs = br->br_sysfs;
+		snprintf(br_sysfs[AuBrSysfs_BR].name, sizeof(br_sysfs->name),
+			 SysaufsBr_PREFIX "%d", bindex);
+		snprintf(br_sysfs[AuBrSysfs_BRID].name, sizeof(br_sysfs->name),
+			 SysaufsBrid_PREFIX "%d", bindex);
+		for (i = 0; i < ARRAY_SIZE(br->br_sysfs); i++) {
+			err = sysfs_create_file(kobj, &br_sysfs->attr);
+			if (unlikely(err))
+				pr_warn("failed %s under sysfs(%d)\n",
+					br_sysfs->name, err);
+			br_sysfs++;
+		}
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/sysrq.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/sysrq.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * magic sysrq handler
+ */
+
+/* #include <linux/sysrq.h> */
+#include <linux/writeback.h>
+#include "aufs.h"
+
+/* ---------------------------------------------------------------------- */
+
+static void sysrq_sb(struct super_block *sb)
+{
+	char *plevel;
+	struct au_sbinfo *sbinfo;
+	struct file *file;
+	struct hlist_bl_head *files;
+	struct hlist_bl_node *pos;
+	struct au_finfo *finfo;
+	struct inode *i;
+
+	plevel = au_plevel;
+	au_plevel = KERN_WARNING;
+
+	/* since we define pr_fmt, call printk directly */
+#define pr(str) printk(KERN_WARNING AUFS_NAME ": " str)
+
+	sbinfo = au_sbi(sb);
+	printk(KERN_WARNING "si=%lx\n", sysaufs_si_id(sbinfo));
+	pr("superblock\n");
+	au_dpri_sb(sb);
+
+#if 0 /* reserved */
+	do {
+		int err, i, j, ndentry;
+		struct au_dcsub_pages dpages;
+		struct au_dpage *dpage;
+
+		err = au_dpages_init(&dpages, GFP_ATOMIC);
+		if (unlikely(err))
+			break;
+		err = au_dcsub_pages(&dpages, sb->s_root, NULL, NULL);
+		if (!err)
+			for (i = 0; i < dpages.ndpage; i++) {
+				dpage = dpages.dpages + i;
+				ndentry = dpage->ndentry;
+				for (j = 0; j < ndentry; j++)
+					au_dpri_dentry(dpage->dentries[j]);
+			}
+		au_dpages_free(&dpages);
+	} while (0);
+#endif
+
+	pr("isolated inode\n");
+	spin_lock(&sb->s_inode_list_lock);
+	list_for_each_entry(i, &sb->s_inodes, i_sb_list) {
+		spin_lock(&i->i_lock);
+		if (hlist_empty(&i->i_dentry))
+			au_dpri_inode(i);
+		spin_unlock(&i->i_lock);
+	}
+	spin_unlock(&sb->s_inode_list_lock);
+
+	pr("files\n");
+	files = &au_sbi(sb)->si_files;
+	hlist_bl_lock(files);
+	hlist_bl_for_each_entry(finfo, pos, files, fi_hlist) {
+		umode_t mode;
+
+		file = finfo->fi_file;
+		mode = file_inode(file)->i_mode;
+		if (!special_file(mode))
+			au_dpri_file(file);
+	}
+	hlist_bl_unlock(files);
+	pr("done\n");
+
+#undef pr
+	au_plevel = plevel;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* module parameter */
+static char *aufs_sysrq_key = "a";
+module_param_named(sysrq, aufs_sysrq_key, charp, 0444);
+MODULE_PARM_DESC(sysrq, "MagicSysRq key for " AUFS_NAME);
+
+static void au_sysrq(int key __maybe_unused)
+{
+	struct au_sbinfo *sbinfo;
+	struct hlist_bl_node *pos;
+
+	lockdep_off();
+	au_sbilist_lock();
+	hlist_bl_for_each_entry(sbinfo, pos, &au_sbilist, si_list)
+		sysrq_sb(sbinfo->si_sb);
+	au_sbilist_unlock();
+	lockdep_on();
+}
+
+static struct sysrq_key_op au_sysrq_op = {
+	.handler	= au_sysrq,
+	.help_msg	= "Aufs",
+	.action_msg	= "Aufs",
+	.enable_mask	= SYSRQ_ENABLE_DUMP
+};
+
+/* ---------------------------------------------------------------------- */
+
+int __init au_sysrq_init(void)
+{
+	int err;
+	char key;
+
+	err = -1;
+	key = *aufs_sysrq_key;
+	if ('a' <= key && key <= 'z')
+		err = register_sysrq_key(key, &au_sysrq_op);
+	if (unlikely(err))
+		pr_err("err %d, sysrq=%c\n", err, key);
+	return err;
+}
+
+void au_sysrq_fin(void)
+{
+	int err;
+
+	err = unregister_sysrq_key(*aufs_sysrq_key, &au_sysrq_op);
+	if (unlikely(err))
+		pr_err("err %d (ignored)\n", err);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/vdir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/vdir.c
@@ -0,0 +1,896 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * virtual or vertical directory
+ */
+
+#include <linux/iversion.h>
+#include "aufs.h"
+
+static unsigned int calc_size(int nlen)
+{
+	return ALIGN(sizeof(struct au_vdir_de) + nlen, sizeof(ino_t));
+}
+
+static int set_deblk_end(union au_vdir_deblk_p *p,
+			 union au_vdir_deblk_p *deblk_end)
+{
+	if (calc_size(0) <= deblk_end->deblk - p->deblk) {
+		p->de->de_str.len = 0;
+		/* smp_mb(); */
+		return 0;
+	}
+	return -1; /* error */
+}
+
+/* returns true or false */
+static int is_deblk_end(union au_vdir_deblk_p *p,
+			union au_vdir_deblk_p *deblk_end)
+{
+	if (calc_size(0) <= deblk_end->deblk - p->deblk)
+		return !p->de->de_str.len;
+	return 1;
+}
+
+static unsigned char *last_deblk(struct au_vdir *vdir)
+{
+	return vdir->vd_deblk[vdir->vd_nblk - 1];
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* estimate the appropriate size for name hash table */
+unsigned int au_rdhash_est(loff_t sz)
+{
+	unsigned int n;
+
+	n = UINT_MAX;
+	sz >>= 10;
+	if (sz < n)
+		n = sz;
+	if (sz < AUFS_RDHASH_DEF)
+		n = AUFS_RDHASH_DEF;
+	/* pr_info("n %u\n", n); */
+	return n;
+}
+
+/*
+ * the allocated memory has to be freed by
+ * au_nhash_wh_free() or au_nhash_de_free().
+ */
+int au_nhash_alloc(struct au_nhash *nhash, unsigned int num_hash, gfp_t gfp)
+{
+	struct hlist_head *head;
+	unsigned int u;
+	size_t sz;
+
+	sz = sizeof(*nhash->nh_head) * num_hash;
+	head = kmalloc(sz, gfp);
+	if (head) {
+		nhash->nh_num = num_hash;
+		nhash->nh_head = head;
+		for (u = 0; u < num_hash; u++)
+			INIT_HLIST_HEAD(head++);
+		return 0; /* success */
+	}
+
+	return -ENOMEM;
+}
+
+static void nhash_count(struct hlist_head *head)
+{
+#if 0 /* debugging */
+	unsigned long n;
+	struct hlist_node *pos;
+
+	n = 0;
+	hlist_for_each(pos, head)
+		n++;
+	pr_info("%lu\n", n);
+#endif
+}
+
+static void au_nhash_wh_do_free(struct hlist_head *head)
+{
+	struct au_vdir_wh *pos;
+	struct hlist_node *node;
+
+	hlist_for_each_entry_safe(pos, node, head, wh_hash)
+		au_kfree_rcu(pos);
+}
+
+static void au_nhash_de_do_free(struct hlist_head *head)
+{
+	struct au_vdir_dehstr *pos;
+	struct hlist_node *node;
+
+	hlist_for_each_entry_safe(pos, node, head, hash)
+		au_cache_free_vdir_dehstr(pos);
+}
+
+static void au_nhash_do_free(struct au_nhash *nhash,
+			     void (*free)(struct hlist_head *head))
+{
+	unsigned int n;
+	struct hlist_head *head;
+
+	n = nhash->nh_num;
+	if (!n)
+		return;
+
+	head = nhash->nh_head;
+	while (n-- > 0) {
+		nhash_count(head);
+		free(head++);
+	}
+	au_kfree_try_rcu(nhash->nh_head);
+}
+
+void au_nhash_wh_free(struct au_nhash *whlist)
+{
+	au_nhash_do_free(whlist, au_nhash_wh_do_free);
+}
+
+static void au_nhash_de_free(struct au_nhash *delist)
+{
+	au_nhash_do_free(delist, au_nhash_de_do_free);
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_nhash_test_longer_wh(struct au_nhash *whlist, aufs_bindex_t btgt,
+			    int limit)
+{
+	int num;
+	unsigned int u, n;
+	struct hlist_head *head;
+	struct au_vdir_wh *pos;
+
+	num = 0;
+	n = whlist->nh_num;
+	head = whlist->nh_head;
+	for (u = 0; u < n; u++, head++)
+		hlist_for_each_entry(pos, head, wh_hash)
+			if (pos->wh_bindex == btgt && ++num > limit)
+				return 1;
+	return 0;
+}
+
+static struct hlist_head *au_name_hash(struct au_nhash *nhash,
+				       unsigned char *name,
+				       unsigned int len)
+{
+	unsigned int v;
+	/* const unsigned int magic_bit = 12; */
+
+	AuDebugOn(!nhash->nh_num || !nhash->nh_head);
+
+	v = 0;
+	if (len > 8)
+		len = 8;
+	while (len--)
+		v += *name++;
+	/* v = hash_long(v, magic_bit); */
+	v %= nhash->nh_num;
+	return nhash->nh_head + v;
+}
+
+static int au_nhash_test_name(struct au_vdir_destr *str, const char *name,
+			      int nlen)
+{
+	return str->len == nlen && !memcmp(str->name, name, nlen);
+}
+
+/* returns found or not */
+int au_nhash_test_known_wh(struct au_nhash *whlist, char *name, int nlen)
+{
+	struct hlist_head *head;
+	struct au_vdir_wh *pos;
+	struct au_vdir_destr *str;
+
+	head = au_name_hash(whlist, name, nlen);
+	hlist_for_each_entry(pos, head, wh_hash) {
+		str = &pos->wh_str;
+		AuDbg("%.*s\n", str->len, str->name);
+		if (au_nhash_test_name(str, name, nlen))
+			return 1;
+	}
+	return 0;
+}
+
+/* returns found(true) or not */
+static int test_known(struct au_nhash *delist, char *name, int nlen)
+{
+	struct hlist_head *head;
+	struct au_vdir_dehstr *pos;
+	struct au_vdir_destr *str;
+
+	head = au_name_hash(delist, name, nlen);
+	hlist_for_each_entry(pos, head, hash) {
+		str = pos->str;
+		AuDbg("%.*s\n", str->len, str->name);
+		if (au_nhash_test_name(str, name, nlen))
+			return 1;
+	}
+	return 0;
+}
+
+static void au_shwh_init_wh(struct au_vdir_wh *wh, ino_t ino,
+			    unsigned char d_type)
+{
+#ifdef CONFIG_AUFS_SHWH
+	wh->wh_ino = ino;
+	wh->wh_type = d_type;
+#endif
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_nhash_append_wh(struct au_nhash *whlist, char *name, int nlen, ino_t ino,
+		       unsigned int d_type, aufs_bindex_t bindex,
+		       unsigned char shwh)
+{
+	int err;
+	struct au_vdir_destr *str;
+	struct au_vdir_wh *wh;
+
+	AuDbg("%.*s\n", nlen, name);
+	AuDebugOn(!whlist->nh_num || !whlist->nh_head);
+
+	err = -ENOMEM;
+	wh = kmalloc(sizeof(*wh) + nlen, GFP_NOFS);
+	if (unlikely(!wh))
+		goto out;
+
+	err = 0;
+	wh->wh_bindex = bindex;
+	if (shwh)
+		au_shwh_init_wh(wh, ino, d_type);
+	str = &wh->wh_str;
+	str->len = nlen;
+	memcpy(str->name, name, nlen);
+	hlist_add_head(&wh->wh_hash, au_name_hash(whlist, name, nlen));
+	/* smp_mb(); */
+
+out:
+	return err;
+}
+
+static int append_deblk(struct au_vdir *vdir)
+{
+	int err;
+	unsigned long ul;
+	const unsigned int deblk_sz = vdir->vd_deblk_sz;
+	union au_vdir_deblk_p p, deblk_end;
+	unsigned char **o;
+
+	err = -ENOMEM;
+	o = au_krealloc(vdir->vd_deblk, sizeof(*o) * (vdir->vd_nblk + 1),
+			GFP_NOFS, /*may_shrink*/0);
+	if (unlikely(!o))
+		goto out;
+
+	vdir->vd_deblk = o;
+	p.deblk = kmalloc(deblk_sz, GFP_NOFS);
+	if (p.deblk) {
+		ul = vdir->vd_nblk++;
+		vdir->vd_deblk[ul] = p.deblk;
+		vdir->vd_last.ul = ul;
+		vdir->vd_last.p.deblk = p.deblk;
+		deblk_end.deblk = p.deblk + deblk_sz;
+		err = set_deblk_end(&p, &deblk_end);
+	}
+
+out:
+	return err;
+}
+
+static int append_de(struct au_vdir *vdir, char *name, int nlen, ino_t ino,
+		     unsigned int d_type, struct au_nhash *delist)
+{
+	int err;
+	unsigned int sz;
+	const unsigned int deblk_sz = vdir->vd_deblk_sz;
+	union au_vdir_deblk_p p, *room, deblk_end;
+	struct au_vdir_dehstr *dehstr;
+
+	p.deblk = last_deblk(vdir);
+	deblk_end.deblk = p.deblk + deblk_sz;
+	room = &vdir->vd_last.p;
+	AuDebugOn(room->deblk < p.deblk || deblk_end.deblk <= room->deblk
+		  || !is_deblk_end(room, &deblk_end));
+
+	sz = calc_size(nlen);
+	if (unlikely(sz > deblk_end.deblk - room->deblk)) {
+		err = append_deblk(vdir);
+		if (unlikely(err))
+			goto out;
+
+		p.deblk = last_deblk(vdir);
+		deblk_end.deblk = p.deblk + deblk_sz;
+		/* smp_mb(); */
+		AuDebugOn(room->deblk != p.deblk);
+	}
+
+	err = -ENOMEM;
+	dehstr = au_cache_alloc_vdir_dehstr();
+	if (unlikely(!dehstr))
+		goto out;
+
+	dehstr->str = &room->de->de_str;
+	hlist_add_head(&dehstr->hash, au_name_hash(delist, name, nlen));
+	room->de->de_ino = ino;
+	room->de->de_type = d_type;
+	room->de->de_str.len = nlen;
+	memcpy(room->de->de_str.name, name, nlen);
+
+	err = 0;
+	room->deblk += sz;
+	if (unlikely(set_deblk_end(room, &deblk_end)))
+		err = append_deblk(vdir);
+	/* smp_mb(); */
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_vdir_free(struct au_vdir *vdir)
+{
+	unsigned char **deblk;
+
+	deblk = vdir->vd_deblk;
+	while (vdir->vd_nblk--)
+		au_kfree_try_rcu(*deblk++);
+	au_kfree_try_rcu(vdir->vd_deblk);
+	au_cache_free_vdir(vdir);
+}
+
+static struct au_vdir *alloc_vdir(struct file *file)
+{
+	struct au_vdir *vdir;
+	struct super_block *sb;
+	int err;
+
+	sb = file->f_path.dentry->d_sb;
+	SiMustAnyLock(sb);
+
+	err = -ENOMEM;
+	vdir = au_cache_alloc_vdir();
+	if (unlikely(!vdir))
+		goto out;
+
+	vdir->vd_deblk = kzalloc(sizeof(*vdir->vd_deblk), GFP_NOFS);
+	if (unlikely(!vdir->vd_deblk))
+		goto out_free;
+
+	vdir->vd_deblk_sz = au_sbi(sb)->si_rdblk;
+	if (!vdir->vd_deblk_sz) {
+		/* estimate the appropriate size for deblk */
+		vdir->vd_deblk_sz = au_dir_size(file, /*dentry*/NULL);
+		/* pr_info("vd_deblk_sz %u\n", vdir->vd_deblk_sz); */
+	}
+	vdir->vd_nblk = 0;
+	vdir->vd_version = 0;
+	vdir->vd_jiffy = 0;
+	err = append_deblk(vdir);
+	if (!err)
+		return vdir; /* success */
+
+	au_kfree_try_rcu(vdir->vd_deblk);
+
+out_free:
+	au_cache_free_vdir(vdir);
+out:
+	vdir = ERR_PTR(err);
+	return vdir;
+}
+
+static int reinit_vdir(struct au_vdir *vdir)
+{
+	int err;
+	union au_vdir_deblk_p p, deblk_end;
+
+	while (vdir->vd_nblk > 1) {
+		au_kfree_try_rcu(vdir->vd_deblk[vdir->vd_nblk - 1]);
+		/* vdir->vd_deblk[vdir->vd_nblk - 1] = NULL; */
+		vdir->vd_nblk--;
+	}
+	p.deblk = vdir->vd_deblk[0];
+	deblk_end.deblk = p.deblk + vdir->vd_deblk_sz;
+	err = set_deblk_end(&p, &deblk_end);
+	/* keep vd_dblk_sz */
+	vdir->vd_last.ul = 0;
+	vdir->vd_last.p.deblk = vdir->vd_deblk[0];
+	vdir->vd_version = 0;
+	vdir->vd_jiffy = 0;
+	/* smp_mb(); */
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+#define AuFillVdir_CALLED	1
+#define AuFillVdir_WHABLE	(1 << 1)
+#define AuFillVdir_SHWH		(1 << 2)
+#define au_ftest_fillvdir(flags, name)	((flags) & AuFillVdir_##name)
+#define au_fset_fillvdir(flags, name) \
+	do { (flags) |= AuFillVdir_##name; } while (0)
+#define au_fclr_fillvdir(flags, name) \
+	do { (flags) &= ~AuFillVdir_##name; } while (0)
+
+#ifndef CONFIG_AUFS_SHWH
+#undef AuFillVdir_SHWH
+#define AuFillVdir_SHWH		0
+#endif
+
+struct fillvdir_arg {
+	struct dir_context	ctx;
+	struct file		*file;
+	struct au_vdir		*vdir;
+	struct au_nhash		delist;
+	struct au_nhash		whlist;
+	aufs_bindex_t		bindex;
+	unsigned int		flags;
+	int			err;
+};
+
+static int fillvdir(struct dir_context *ctx, const char *__name, int nlen,
+		    loff_t offset __maybe_unused, u64 h_ino,
+		    unsigned int d_type)
+{
+	struct fillvdir_arg *arg = container_of(ctx, struct fillvdir_arg, ctx);
+	char *name = (void *)__name;
+	struct super_block *sb;
+	ino_t ino;
+	const unsigned char shwh = !!au_ftest_fillvdir(arg->flags, SHWH);
+
+	arg->err = 0;
+	sb = arg->file->f_path.dentry->d_sb;
+	au_fset_fillvdir(arg->flags, CALLED);
+	/* smp_mb(); */
+	if (nlen <= AUFS_WH_PFX_LEN
+	    || memcmp(name, AUFS_WH_PFX, AUFS_WH_PFX_LEN)) {
+		if (test_known(&arg->delist, name, nlen)
+		    || au_nhash_test_known_wh(&arg->whlist, name, nlen))
+			goto out; /* already exists or whiteouted */
+
+		arg->err = au_ino(sb, arg->bindex, h_ino, d_type, &ino);
+		if (!arg->err) {
+			if (unlikely(nlen > AUFS_MAX_NAMELEN))
+				d_type = DT_UNKNOWN;
+			arg->err = append_de(arg->vdir, name, nlen, ino,
+					     d_type, &arg->delist);
+		}
+	} else if (au_ftest_fillvdir(arg->flags, WHABLE)) {
+		name += AUFS_WH_PFX_LEN;
+		nlen -= AUFS_WH_PFX_LEN;
+		if (au_nhash_test_known_wh(&arg->whlist, name, nlen))
+			goto out; /* already whiteouted */
+
+		ino = 0; /* just to suppress a warning */
+		if (shwh)
+			arg->err = au_wh_ino(sb, arg->bindex, h_ino, d_type,
+					     &ino);
+		if (!arg->err) {
+			if (nlen <= AUFS_MAX_NAMELEN + AUFS_WH_PFX_LEN)
+				d_type = DT_UNKNOWN;
+			arg->err = au_nhash_append_wh
+				(&arg->whlist, name, nlen, ino, d_type,
+				 arg->bindex, shwh);
+		}
+	}
+
+out:
+	if (!arg->err)
+		arg->vdir->vd_jiffy = jiffies;
+	/* smp_mb(); */
+	AuTraceErr(arg->err);
+	return arg->err;
+}
+
+static int au_handle_shwh(struct super_block *sb, struct au_vdir *vdir,
+			  struct au_nhash *whlist, struct au_nhash *delist)
+{
+#ifdef CONFIG_AUFS_SHWH
+	int err;
+	unsigned int nh, u;
+	struct hlist_head *head;
+	struct au_vdir_wh *pos;
+	struct hlist_node *n;
+	char *p, *o;
+	struct au_vdir_destr *destr;
+
+	AuDebugOn(!au_opt_test(au_mntflags(sb), SHWH));
+
+	err = -ENOMEM;
+	o = p = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!p))
+		goto out;
+
+	err = 0;
+	nh = whlist->nh_num;
+	memcpy(p, AUFS_WH_PFX, AUFS_WH_PFX_LEN);
+	p += AUFS_WH_PFX_LEN;
+	for (u = 0; u < nh; u++) {
+		head = whlist->nh_head + u;
+		hlist_for_each_entry_safe(pos, n, head, wh_hash) {
+			destr = &pos->wh_str;
+			memcpy(p, destr->name, destr->len);
+			err = append_de(vdir, o, destr->len + AUFS_WH_PFX_LEN,
+					pos->wh_ino, pos->wh_type, delist);
+			if (unlikely(err))
+				break;
+		}
+	}
+
+	free_page((unsigned long)o);
+
+out:
+	AuTraceErr(err);
+	return err;
+#else
+	return 0;
+#endif
+}
+
+static int au_do_read_vdir(struct fillvdir_arg *arg)
+{
+	int err;
+	unsigned int rdhash;
+	loff_t offset;
+	aufs_bindex_t bbot, bindex, btop;
+	unsigned char shwh;
+	struct file *hf, *file;
+	struct super_block *sb;
+
+	file = arg->file;
+	sb = file->f_path.dentry->d_sb;
+	SiMustAnyLock(sb);
+
+	rdhash = au_sbi(sb)->si_rdhash;
+	if (!rdhash)
+		rdhash = au_rdhash_est(au_dir_size(file, /*dentry*/NULL));
+	err = au_nhash_alloc(&arg->delist, rdhash, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+	err = au_nhash_alloc(&arg->whlist, rdhash, GFP_NOFS);
+	if (unlikely(err))
+		goto out_delist;
+
+	err = 0;
+	arg->flags = 0;
+	shwh = 0;
+	if (au_opt_test(au_mntflags(sb), SHWH)) {
+		shwh = 1;
+		au_fset_fillvdir(arg->flags, SHWH);
+	}
+	btop = au_fbtop(file);
+	bbot = au_fbbot_dir(file);
+	for (bindex = btop; !err && bindex <= bbot; bindex++) {
+		hf = au_hf_dir(file, bindex);
+		if (!hf)
+			continue;
+
+		offset = vfsub_llseek(hf, 0, SEEK_SET);
+		err = offset;
+		if (unlikely(offset))
+			break;
+
+		arg->bindex = bindex;
+		au_fclr_fillvdir(arg->flags, WHABLE);
+		if (shwh
+		    || (bindex != bbot
+			&& au_br_whable(au_sbr_perm(sb, bindex))))
+			au_fset_fillvdir(arg->flags, WHABLE);
+		do {
+			arg->err = 0;
+			au_fclr_fillvdir(arg->flags, CALLED);
+			/* smp_mb(); */
+			err = vfsub_iterate_dir(hf, &arg->ctx);
+			if (err >= 0)
+				err = arg->err;
+		} while (!err && au_ftest_fillvdir(arg->flags, CALLED));
+
+		/*
+		 * dir_relax() may be good for concurrency, but aufs should not
+		 * use it since it will cause a lockdep problem.
+		 */
+	}
+
+	if (!err && shwh)
+		err = au_handle_shwh(sb, arg->vdir, &arg->whlist, &arg->delist);
+
+	au_nhash_wh_free(&arg->whlist);
+
+out_delist:
+	au_nhash_de_free(&arg->delist);
+out:
+	return err;
+}
+
+static int read_vdir(struct file *file, int may_read)
+{
+	int err;
+	unsigned long expire;
+	unsigned char do_read;
+	struct fillvdir_arg arg = {
+		.ctx = {
+			.actor = fillvdir
+		}
+	};
+	struct inode *inode;
+	struct au_vdir *vdir, *allocated;
+
+	err = 0;
+	inode = file_inode(file);
+	IMustLock(inode);
+	IiMustWriteLock(inode);
+	SiMustAnyLock(inode->i_sb);
+
+	allocated = NULL;
+	do_read = 0;
+	expire = au_sbi(inode->i_sb)->si_rdcache;
+	vdir = au_ivdir(inode);
+	if (!vdir) {
+		do_read = 1;
+		vdir = alloc_vdir(file);
+		err = PTR_ERR(vdir);
+		if (IS_ERR(vdir))
+			goto out;
+		err = 0;
+		allocated = vdir;
+	} else if (may_read
+		   && (!inode_eq_iversion(inode, vdir->vd_version)
+		       || time_after(jiffies, vdir->vd_jiffy + expire))) {
+		do_read = 1;
+		err = reinit_vdir(vdir);
+		if (unlikely(err))
+			goto out;
+	}
+
+	if (!do_read)
+		return 0; /* success */
+
+	arg.file = file;
+	arg.vdir = vdir;
+	err = au_do_read_vdir(&arg);
+	if (!err) {
+		/* file->f_pos = 0; */ /* todo: ctx->pos? */
+		vdir->vd_version = inode_query_iversion(inode);
+		vdir->vd_last.ul = 0;
+		vdir->vd_last.p.deblk = vdir->vd_deblk[0];
+		if (allocated)
+			au_set_ivdir(inode, allocated);
+	} else if (allocated)
+		au_vdir_free(allocated);
+
+out:
+	return err;
+}
+
+static int copy_vdir(struct au_vdir *tgt, struct au_vdir *src)
+{
+	int err, rerr;
+	unsigned long ul, n;
+	const unsigned int deblk_sz = src->vd_deblk_sz;
+
+	AuDebugOn(tgt->vd_nblk != 1);
+
+	err = -ENOMEM;
+	if (tgt->vd_nblk < src->vd_nblk) {
+		unsigned char **p;
+
+		p = au_krealloc(tgt->vd_deblk, sizeof(*p) * src->vd_nblk,
+				GFP_NOFS, /*may_shrink*/0);
+		if (unlikely(!p))
+			goto out;
+		tgt->vd_deblk = p;
+	}
+
+	if (tgt->vd_deblk_sz != deblk_sz) {
+		unsigned char *p;
+
+		tgt->vd_deblk_sz = deblk_sz;
+		p = au_krealloc(tgt->vd_deblk[0], deblk_sz, GFP_NOFS,
+				/*may_shrink*/1);
+		if (unlikely(!p))
+			goto out;
+		tgt->vd_deblk[0] = p;
+	}
+	memcpy(tgt->vd_deblk[0], src->vd_deblk[0], deblk_sz);
+	tgt->vd_version = src->vd_version;
+	tgt->vd_jiffy = src->vd_jiffy;
+
+	n = src->vd_nblk;
+	for (ul = 1; ul < n; ul++) {
+		tgt->vd_deblk[ul] = kmemdup(src->vd_deblk[ul], deblk_sz,
+					    GFP_NOFS);
+		if (unlikely(!tgt->vd_deblk[ul]))
+			goto out;
+		tgt->vd_nblk++;
+	}
+	tgt->vd_nblk = n;
+	tgt->vd_last.ul = tgt->vd_last.ul;
+	tgt->vd_last.p.deblk = tgt->vd_deblk[tgt->vd_last.ul];
+	tgt->vd_last.p.deblk += src->vd_last.p.deblk
+		- src->vd_deblk[src->vd_last.ul];
+	/* smp_mb(); */
+	return 0; /* success */
+
+out:
+	rerr = reinit_vdir(tgt);
+	BUG_ON(rerr);
+	return err;
+}
+
+int au_vdir_init(struct file *file)
+{
+	int err;
+	struct inode *inode;
+	struct au_vdir *vdir_cache, *allocated;
+
+	/* test file->f_pos here instead of ctx->pos */
+	err = read_vdir(file, !file->f_pos);
+	if (unlikely(err))
+		goto out;
+
+	allocated = NULL;
+	vdir_cache = au_fvdir_cache(file);
+	if (!vdir_cache) {
+		vdir_cache = alloc_vdir(file);
+		err = PTR_ERR(vdir_cache);
+		if (IS_ERR(vdir_cache))
+			goto out;
+		allocated = vdir_cache;
+	} else if (!file->f_pos && vdir_cache->vd_version != file->f_version) {
+		/* test file->f_pos here instead of ctx->pos */
+		err = reinit_vdir(vdir_cache);
+		if (unlikely(err))
+			goto out;
+	} else
+		return 0; /* success */
+
+	inode = file_inode(file);
+	err = copy_vdir(vdir_cache, au_ivdir(inode));
+	if (!err) {
+		file->f_version = inode_query_iversion(inode);
+		if (allocated)
+			au_set_fvdir_cache(file, allocated);
+	} else if (allocated)
+		au_vdir_free(allocated);
+
+out:
+	return err;
+}
+
+static loff_t calc_offset(struct au_vdir *vdir)
+{
+	loff_t offset;
+	union au_vdir_deblk_p p;
+
+	p.deblk = vdir->vd_deblk[vdir->vd_last.ul];
+	offset = vdir->vd_last.p.deblk - p.deblk;
+	offset += vdir->vd_deblk_sz * vdir->vd_last.ul;
+	return offset;
+}
+
+/* returns true or false */
+static int seek_vdir(struct file *file, struct dir_context *ctx)
+{
+	int valid;
+	unsigned int deblk_sz;
+	unsigned long ul, n;
+	loff_t offset;
+	union au_vdir_deblk_p p, deblk_end;
+	struct au_vdir *vdir_cache;
+
+	valid = 1;
+	vdir_cache = au_fvdir_cache(file);
+	offset = calc_offset(vdir_cache);
+	AuDbg("offset %lld\n", offset);
+	if (ctx->pos == offset)
+		goto out;
+
+	vdir_cache->vd_last.ul = 0;
+	vdir_cache->vd_last.p.deblk = vdir_cache->vd_deblk[0];
+	if (!ctx->pos)
+		goto out;
+
+	valid = 0;
+	deblk_sz = vdir_cache->vd_deblk_sz;
+	ul = div64_u64(ctx->pos, deblk_sz);
+	AuDbg("ul %lu\n", ul);
+	if (ul >= vdir_cache->vd_nblk)
+		goto out;
+
+	n = vdir_cache->vd_nblk;
+	for (; ul < n; ul++) {
+		p.deblk = vdir_cache->vd_deblk[ul];
+		deblk_end.deblk = p.deblk + deblk_sz;
+		offset = ul;
+		offset *= deblk_sz;
+		while (!is_deblk_end(&p, &deblk_end) && offset < ctx->pos) {
+			unsigned int l;
+
+			l = calc_size(p.de->de_str.len);
+			offset += l;
+			p.deblk += l;
+		}
+		if (!is_deblk_end(&p, &deblk_end)) {
+			valid = 1;
+			vdir_cache->vd_last.ul = ul;
+			vdir_cache->vd_last.p = p;
+			break;
+		}
+	}
+
+out:
+	/* smp_mb(); */
+	if (!valid)
+		AuDbg("valid %d\n", !valid);
+	return valid;
+}
+
+int au_vdir_fill_de(struct file *file, struct dir_context *ctx)
+{
+	unsigned int l, deblk_sz;
+	union au_vdir_deblk_p deblk_end;
+	struct au_vdir *vdir_cache;
+	struct au_vdir_de *de;
+
+	if (!seek_vdir(file, ctx))
+		return 0;
+
+	vdir_cache = au_fvdir_cache(file);
+	deblk_sz = vdir_cache->vd_deblk_sz;
+	while (1) {
+		deblk_end.deblk = vdir_cache->vd_deblk[vdir_cache->vd_last.ul];
+		deblk_end.deblk += deblk_sz;
+		while (!is_deblk_end(&vdir_cache->vd_last.p, &deblk_end)) {
+			de = vdir_cache->vd_last.p.de;
+			AuDbg("%.*s, off%lld, i%lu, dt%d\n",
+			      de->de_str.len, de->de_str.name, ctx->pos,
+			      (unsigned long)de->de_ino, de->de_type);
+			if (unlikely(!dir_emit(ctx, de->de_str.name,
+					       de->de_str.len, de->de_ino,
+					       de->de_type))) {
+				/* todo: ignore the error caused by udba? */
+				/* return err; */
+				return 0;
+			}
+
+			l = calc_size(de->de_str.len);
+			vdir_cache->vd_last.p.deblk += l;
+			ctx->pos += l;
+		}
+		if (vdir_cache->vd_last.ul < vdir_cache->vd_nblk - 1) {
+			vdir_cache->vd_last.ul++;
+			vdir_cache->vd_last.p.deblk
+				= vdir_cache->vd_deblk[vdir_cache->vd_last.ul];
+			ctx->pos = deblk_sz * vdir_cache->vd_last.ul;
+			continue;
+		}
+		break;
+	}
+
+	/* smp_mb(); */
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/vfsub.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/vfsub.c
@@ -0,0 +1,919 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sub-routines for VFS
+ */
+
+#include <linux/mnt_namespace.h>
+#include <linux/namei.h>
+#include <linux/nsproxy.h>
+#include <linux/security.h>
+#include <linux/splice.h>
+#include "aufs.h"
+
+#ifdef CONFIG_AUFS_BR_FUSE
+int vfsub_test_mntns(struct vfsmount *mnt, struct super_block *h_sb)
+{
+	if (!au_test_fuse(h_sb) || !au_userns)
+		return 0;
+
+	return is_current_mnt_ns(mnt) ? 0 : -EACCES;
+}
+#endif
+
+int vfsub_sync_filesystem(struct super_block *h_sb, int wait)
+{
+	int err;
+
+	lockdep_off();
+	down_read(&h_sb->s_umount);
+	err = __sync_filesystem(h_sb, wait);
+	up_read(&h_sb->s_umount);
+	lockdep_on();
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int vfsub_update_h_iattr(struct path *h_path, int *did)
+{
+	int err;
+	struct kstat st;
+	struct super_block *h_sb;
+
+	/*
+	 * Always needs h_path->mnt for LSM or FUSE branch.
+	 */
+	AuDebugOn(!h_path->mnt);
+
+	/* for remote fs, leave work for its getattr or d_revalidate */
+	/* for bad i_attr fs, handle them in aufs_getattr() */
+	/* still some fs may acquire i_mutex. we need to skip them */
+	err = 0;
+	if (!did)
+		did = &err;
+	h_sb = h_path->dentry->d_sb;
+	*did = (!au_test_fs_remote(h_sb) && au_test_fs_refresh_iattr(h_sb));
+	if (*did)
+		err = vfsub_getattr(h_path, &st);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct file *vfsub_dentry_open(struct path *path, int flags)
+{
+	return dentry_open(path, flags /* | __FMODE_NONOTIFY */,
+			   current_cred());
+}
+
+struct file *vfsub_filp_open(const char *path, int oflags, int mode)
+{
+	struct file *file;
+
+	lockdep_off();
+	file = filp_open(path,
+			 oflags /* | __FMODE_NONOTIFY */,
+			 mode);
+	lockdep_on();
+	if (IS_ERR(file))
+		goto out;
+	vfsub_update_h_iattr(&file->f_path, /*did*/NULL); /*ignore*/
+
+out:
+	return file;
+}
+
+/*
+ * Ideally this function should call VFS:do_last() in order to keep all its
+ * checkings. But it is very hard for aufs to regenerate several VFS internal
+ * structure such as nameidata. This is a second (or third) best approach.
+ * cf. linux/fs/namei.c:do_last(), lookup_open() and atomic_open().
+ */
+int vfsub_atomic_open(struct inode *dir, struct dentry *dentry,
+		      struct vfsub_aopen_args *args)
+{
+	int err;
+	struct au_branch *br = args->br;
+	struct file *file = args->file;
+	/* copied from linux/fs/namei.c:atomic_open() */
+	struct dentry *const DENTRY_NOT_SET = (void *)-1UL;
+
+	IMustLock(dir);
+	AuDebugOn(!dir->i_op->atomic_open);
+
+	err = au_br_test_oflag(args->open_flag, br);
+	if (unlikely(err))
+		goto out;
+
+	au_lcnt_inc(&br->br_nfiles);
+	file->f_path.dentry = DENTRY_NOT_SET;
+	file->f_path.mnt = au_br_mnt(br);
+	AuDbg("%ps\n", dir->i_op->atomic_open);
+	err = dir->i_op->atomic_open(dir, dentry, file, args->open_flag,
+				     args->create_mode);
+	if (unlikely(err < 0)) {
+		au_lcnt_dec(&br->br_nfiles);
+		goto out;
+	}
+
+	/* temporary workaround for nfsv4 branch */
+	if (au_test_nfs(dir->i_sb))
+		nfs_mark_for_revalidate(dir);
+
+	if (file->f_mode & FMODE_CREATED)
+		fsnotify_create(dir, dentry);
+	if (!(file->f_mode & FMODE_OPENED)) {
+		au_lcnt_dec(&br->br_nfiles);
+		goto out;
+	}
+
+	/* todo: call VFS:may_open() here */
+	/* todo: ima_file_check() too? */
+	if (!err && (args->open_flag & __FMODE_EXEC))
+		err = deny_write_access(file);
+	if (!err)
+		fsnotify_open(file);
+	else
+		au_lcnt_dec(&br->br_nfiles);
+	/* note that the file is created and still opened */
+
+out:
+	return err;
+}
+
+int vfsub_kern_path(const char *name, unsigned int flags, struct path *path)
+{
+	int err;
+
+	err = kern_path(name, flags, path);
+	if (!err && d_is_positive(path->dentry))
+		vfsub_update_h_iattr(path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+struct dentry *vfsub_lookup_one_len_unlocked(const char *name,
+					     struct path *ppath, int len)
+{
+	struct path path;
+
+	path.dentry = lookup_one_len_unlocked(name, ppath->dentry, len);
+	if (IS_ERR(path.dentry))
+		goto out;
+	if (d_is_positive(path.dentry)) {
+		path.mnt = ppath->mnt;
+		vfsub_update_h_iattr(&path, /*did*/NULL); /*ignore*/
+	}
+
+out:
+	AuTraceErrPtr(path.dentry);
+	return path.dentry;
+}
+
+struct dentry *vfsub_lookup_one_len(const char *name, struct path *ppath,
+				    int len)
+{
+	struct path path;
+
+	/* VFS checks it too, but by WARN_ON_ONCE() */
+	IMustLock(d_inode(ppath->dentry));
+
+	path.dentry = lookup_one_len(name, ppath->dentry, len);
+	if (IS_ERR(path.dentry))
+		goto out;
+	if (d_is_positive(path.dentry)) {
+		path.mnt = ppath->mnt;
+		vfsub_update_h_iattr(&path, /*did*/NULL); /*ignore*/
+	}
+
+out:
+	AuTraceErrPtr(path.dentry);
+	return path.dentry;
+}
+
+void vfsub_call_lkup_one(void *args)
+{
+	struct vfsub_lkup_one_args *a = args;
+	*a->errp = vfsub_lkup_one(a->name, a->ppath);
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct dentry *vfsub_lock_rename(struct dentry *d1, struct au_hinode *hdir1,
+				 struct dentry *d2, struct au_hinode *hdir2)
+{
+	struct dentry *d;
+
+	lockdep_off();
+	d = lock_rename(d1, d2);
+	lockdep_on();
+	au_hn_suspend(hdir1);
+	if (hdir1 != hdir2)
+		au_hn_suspend(hdir2);
+
+	return d;
+}
+
+void vfsub_unlock_rename(struct dentry *d1, struct au_hinode *hdir1,
+			 struct dentry *d2, struct au_hinode *hdir2)
+{
+	au_hn_resume(hdir1);
+	if (hdir1 != hdir2)
+		au_hn_resume(hdir2);
+	lockdep_off();
+	unlock_rename(d1, d2);
+	lockdep_on();
+}
+
+/* ---------------------------------------------------------------------- */
+
+int vfsub_create(struct inode *dir, struct path *path, int mode, bool want_excl)
+{
+	int err;
+	struct dentry *d;
+	struct user_namespace *userns;
+
+	IMustLock(dir);
+
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	err = security_path_mknod(path, d, mode, 0);
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+	userns = mnt_user_ns(path->mnt);
+
+	lockdep_off();
+	err = vfs_create(userns, dir, path->dentry, mode, want_excl);
+	lockdep_on();
+	if (!err) {
+		struct path tmp = *path;
+		int did;
+
+		vfsub_update_h_iattr(&tmp, &did);
+		if (did) {
+			tmp.dentry = path->dentry->d_parent;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+		}
+		/*ignore*/
+	}
+
+out:
+	return err;
+}
+
+int vfsub_symlink(struct inode *dir, struct path *path, const char *symname)
+{
+	int err;
+	struct dentry *d;
+	struct user_namespace *userns;
+
+	IMustLock(dir);
+
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	err = security_path_symlink(path, d, symname);
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+	userns = mnt_user_ns(path->mnt);
+
+	lockdep_off();
+	err = vfs_symlink(userns, dir, path->dentry, symname);
+	lockdep_on();
+	if (!err) {
+		struct path tmp = *path;
+		int did;
+
+		vfsub_update_h_iattr(&tmp, &did);
+		if (did) {
+			tmp.dentry = path->dentry->d_parent;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+		}
+		/*ignore*/
+	}
+
+out:
+	return err;
+}
+
+int vfsub_mknod(struct inode *dir, struct path *path, int mode, dev_t dev)
+{
+	int err;
+	struct dentry *d;
+	struct user_namespace *userns;
+
+	IMustLock(dir);
+
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	err = security_path_mknod(path, d, mode, new_encode_dev(dev));
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+	userns = mnt_user_ns(path->mnt);
+
+	lockdep_off();
+	err = vfs_mknod(userns, dir, path->dentry, mode, dev);
+	lockdep_on();
+	if (!err) {
+		struct path tmp = *path;
+		int did;
+
+		vfsub_update_h_iattr(&tmp, &did);
+		if (did) {
+			tmp.dentry = path->dentry->d_parent;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+		}
+		/*ignore*/
+	}
+
+out:
+	return err;
+}
+
+static int au_test_nlink(struct inode *inode)
+{
+	const unsigned int link_max = UINT_MAX >> 1; /* rough margin */
+
+	if (!au_test_fs_no_limit_nlink(inode->i_sb)
+	    || inode->i_nlink < link_max)
+		return 0;
+	return -EMLINK;
+}
+
+int vfsub_link(struct dentry *src_dentry, struct inode *dir, struct path *path,
+	       struct inode **delegated_inode)
+{
+	int err;
+	struct dentry *d;
+	struct user_namespace *userns;
+
+	IMustLock(dir);
+
+	err = au_test_nlink(d_inode(src_dentry));
+	if (unlikely(err))
+		return err;
+
+	/* we don't call may_linkat() */
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	err = security_path_link(src_dentry, path, d);
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+	userns = mnt_user_ns(path->mnt);
+
+	lockdep_off();
+	err = vfs_link(src_dentry, userns, dir, path->dentry, delegated_inode);
+	lockdep_on();
+	if (!err) {
+		struct path tmp = *path;
+		int did;
+
+		/* fuse has different memory inode for the same inumber */
+		vfsub_update_h_iattr(&tmp, &did);
+		if (did) {
+			tmp.dentry = path->dentry->d_parent;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+			tmp.dentry = src_dentry;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+		}
+		/*ignore*/
+	}
+
+out:
+	return err;
+}
+
+int vfsub_rename(struct inode *src_dir, struct dentry *src_dentry,
+		 struct inode *dir, struct path *path,
+		 struct inode **delegated_inode, unsigned int flags)
+{
+	int err;
+	struct renamedata rd;
+	struct path tmp = {
+		.mnt	= path->mnt
+	};
+	struct dentry *d;
+
+	IMustLock(dir);
+	IMustLock(src_dir);
+
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	tmp.dentry = src_dentry->d_parent;
+	err = security_path_rename(&tmp, src_dentry, path, d, /*flags*/0);
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+
+	rd.old_mnt_userns = mnt_user_ns(path->mnt);
+	rd.old_dir = src_dir;
+	rd.old_dentry = src_dentry;
+	rd.new_mnt_userns = rd.old_mnt_userns;
+	rd.new_dir = dir;
+	rd.new_dentry = path->dentry;
+	rd.delegated_inode = delegated_inode;
+	rd.flags = flags;
+	lockdep_off();
+	err = vfs_rename(&rd);
+	lockdep_on();
+	if (!err) {
+		int did;
+
+		tmp.dentry = d->d_parent;
+		vfsub_update_h_iattr(&tmp, &did);
+		if (did) {
+			tmp.dentry = src_dentry;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+			tmp.dentry = src_dentry->d_parent;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+		}
+		/*ignore*/
+	}
+
+out:
+	return err;
+}
+
+int vfsub_mkdir(struct inode *dir, struct path *path, int mode)
+{
+	int err;
+	struct dentry *d;
+	struct user_namespace *userns;
+
+	IMustLock(dir);
+
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	err = security_path_mkdir(path, d, mode);
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+	userns = mnt_user_ns(path->mnt);
+
+	lockdep_off();
+	err = vfs_mkdir(userns, dir, path->dentry, mode);
+	lockdep_on();
+	if (!err) {
+		struct path tmp = *path;
+		int did;
+
+		vfsub_update_h_iattr(&tmp, &did);
+		if (did) {
+			tmp.dentry = path->dentry->d_parent;
+			vfsub_update_h_iattr(&tmp, /*did*/NULL);
+		}
+		/*ignore*/
+	}
+
+out:
+	return err;
+}
+
+int vfsub_rmdir(struct inode *dir, struct path *path)
+{
+	int err;
+	struct dentry *d;
+	struct user_namespace *userns;
+
+	IMustLock(dir);
+
+	d = path->dentry;
+	path->dentry = d->d_parent;
+	err = security_path_rmdir(path, d);
+	path->dentry = d;
+	if (unlikely(err))
+		goto out;
+	userns = mnt_user_ns(path->mnt);
+
+	lockdep_off();
+	err = vfs_rmdir(userns, dir, path->dentry);
+	lockdep_on();
+	if (!err) {
+		struct path tmp = {
+			.dentry	= path->dentry->d_parent,
+			.mnt	= path->mnt
+		};
+
+		vfsub_update_h_iattr(&tmp, /*did*/NULL); /*ignore*/
+	}
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* todo: support mmap_sem? */
+ssize_t vfsub_read_u(struct file *file, char __user *ubuf, size_t count,
+		     loff_t *ppos)
+{
+	ssize_t err;
+
+	lockdep_off();
+	err = vfs_read(file, ubuf, count, ppos);
+	lockdep_on();
+	if (err >= 0)
+		vfsub_update_h_iattr(&file->f_path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+ssize_t vfsub_read_k(struct file *file, void *kbuf, size_t count,
+		     loff_t *ppos)
+{
+	ssize_t err;
+
+	lockdep_off();
+	err = kernel_read(file, kbuf, count, ppos);
+	lockdep_on();
+	AuTraceErr(err);
+	if (err >= 0)
+		vfsub_update_h_iattr(&file->f_path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+ssize_t vfsub_write_u(struct file *file, const char __user *ubuf, size_t count,
+		      loff_t *ppos)
+{
+	ssize_t err;
+
+	lockdep_off();
+	err = vfs_write(file, ubuf, count, ppos);
+	lockdep_on();
+	if (err >= 0)
+		vfsub_update_h_iattr(&file->f_path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+ssize_t vfsub_write_k(struct file *file, void *kbuf, size_t count, loff_t *ppos)
+{
+	ssize_t err;
+
+	lockdep_off();
+	err = kernel_write(file, kbuf, count, ppos);
+	lockdep_on();
+	if (err >= 0)
+		vfsub_update_h_iattr(&file->f_path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+int vfsub_flush(struct file *file, fl_owner_t id)
+{
+	int err;
+
+	err = 0;
+	if (file->f_op->flush) {
+		if (!au_test_nfs(file->f_path.dentry->d_sb))
+			err = file->f_op->flush(file, id);
+		else {
+			lockdep_off();
+			err = file->f_op->flush(file, id);
+			lockdep_on();
+		}
+		if (!err)
+			vfsub_update_h_iattr(&file->f_path, /*did*/NULL);
+		/*ignore*/
+	}
+	return err;
+}
+
+int vfsub_iterate_dir(struct file *file, struct dir_context *ctx)
+{
+	int err;
+
+	AuDbg("%pD, ctx{%ps, %llu}\n", file, ctx->actor, ctx->pos);
+
+	lockdep_off();
+	err = iterate_dir(file, ctx);
+	lockdep_on();
+	if (err >= 0)
+		vfsub_update_h_iattr(&file->f_path, /*did*/NULL); /*ignore*/
+
+	return err;
+}
+
+long vfsub_splice_to(struct file *in, loff_t *ppos,
+		     struct pipe_inode_info *pipe, size_t len,
+		     unsigned int flags)
+{
+	long err;
+
+	lockdep_off();
+	err = do_splice_to(in, ppos, pipe, len, flags);
+	lockdep_on();
+	file_accessed(in);
+	if (err >= 0)
+		vfsub_update_h_iattr(&in->f_path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+long vfsub_splice_from(struct pipe_inode_info *pipe, struct file *out,
+		       loff_t *ppos, size_t len, unsigned int flags)
+{
+	long err;
+
+	lockdep_off();
+	err = do_splice_from(pipe, out, ppos, len, flags);
+	lockdep_on();
+	if (err >= 0)
+		vfsub_update_h_iattr(&out->f_path, /*did*/NULL); /*ignore*/
+	return err;
+}
+
+int vfsub_fsync(struct file *file, struct path *path, int datasync)
+{
+	int err;
+
+	/* file can be NULL */
+	lockdep_off();
+	err = vfs_fsync(file, datasync);
+	lockdep_on();
+	if (!err) {
+		if (!path) {
+			AuDebugOn(!file);
+			path = &file->f_path;
+		}
+		vfsub_update_h_iattr(path, /*did*/NULL); /*ignore*/
+	}
+	return err;
+}
+
+/* cf. open.c:do_sys_truncate() and do_sys_ftruncate() */
+int vfsub_trunc(struct path *h_path, loff_t length, unsigned int attr,
+		struct file *h_file)
+{
+	int err;
+	struct inode *h_inode;
+	struct super_block *h_sb;
+	struct user_namespace *h_userns;
+
+	if (!h_file) {
+		err = vfsub_truncate(h_path, length);
+		goto out;
+	}
+
+	h_inode = d_inode(h_path->dentry);
+	h_sb = h_inode->i_sb;
+	lockdep_off();
+	sb_start_write(h_sb);
+	lockdep_on();
+	err = security_path_truncate(h_path);
+	if (!err) {
+		h_userns = mnt_user_ns(h_path->mnt);
+		lockdep_off();
+		err = do_truncate(h_userns, h_path->dentry, length, attr,
+				  h_file);
+		lockdep_on();
+	}
+	lockdep_off();
+	sb_end_write(h_sb);
+	lockdep_on();
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_vfsub_mkdir_args {
+	int *errp;
+	struct inode *dir;
+	struct path *path;
+	int mode;
+};
+
+static void au_call_vfsub_mkdir(void *args)
+{
+	struct au_vfsub_mkdir_args *a = args;
+	*a->errp = vfsub_mkdir(a->dir, a->path, a->mode);
+}
+
+int vfsub_sio_mkdir(struct inode *dir, struct path *path, int mode)
+{
+	int err, do_sio, wkq_err;
+	struct user_namespace *userns;
+
+	userns = mnt_user_ns(path->mnt);
+	do_sio = au_test_h_perm_sio(userns, dir, MAY_EXEC | MAY_WRITE);
+	if (!do_sio) {
+		lockdep_off();
+		err = vfsub_mkdir(dir, path, mode);
+		lockdep_on();
+	} else {
+		struct au_vfsub_mkdir_args args = {
+			.errp	= &err,
+			.dir	= dir,
+			.path	= path,
+			.mode	= mode
+		};
+		wkq_err = au_wkq_wait(au_call_vfsub_mkdir, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+
+	return err;
+}
+
+struct au_vfsub_rmdir_args {
+	int *errp;
+	struct inode *dir;
+	struct path *path;
+};
+
+static void au_call_vfsub_rmdir(void *args)
+{
+	struct au_vfsub_rmdir_args *a = args;
+	*a->errp = vfsub_rmdir(a->dir, a->path);
+}
+
+int vfsub_sio_rmdir(struct inode *dir, struct path *path)
+{
+	int err, do_sio, wkq_err;
+	struct user_namespace *userns;
+
+	userns = mnt_user_ns(path->mnt);
+	do_sio = au_test_h_perm_sio(userns, dir, MAY_EXEC | MAY_WRITE);
+	if (!do_sio) {
+		lockdep_off();
+		err = vfsub_rmdir(dir, path);
+		lockdep_on();
+	} else {
+		struct au_vfsub_rmdir_args args = {
+			.errp	= &err,
+			.dir	= dir,
+			.path	= path
+		};
+		wkq_err = au_wkq_wait(au_call_vfsub_rmdir, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct notify_change_args {
+	int *errp;
+	struct path *path;
+	struct iattr *ia;
+	struct inode **delegated_inode;
+};
+
+static void call_notify_change(void *args)
+{
+	struct notify_change_args *a = args;
+	struct inode *h_inode;
+	struct user_namespace *userns;
+
+	h_inode = d_inode(a->path->dentry);
+	IMustLock(h_inode);
+
+	*a->errp = -EPERM;
+	if (!IS_IMMUTABLE(h_inode) && !IS_APPEND(h_inode)) {
+		userns = mnt_user_ns(a->path->mnt);
+		lockdep_off();
+		*a->errp = notify_change(userns, a->path->dentry, a->ia,
+					 a->delegated_inode);
+		lockdep_on();
+		if (!*a->errp)
+			vfsub_update_h_iattr(a->path, /*did*/NULL); /*ignore*/
+	}
+	AuTraceErr(*a->errp);
+}
+
+int vfsub_notify_change(struct path *path, struct iattr *ia,
+			struct inode **delegated_inode)
+{
+	int err;
+	struct notify_change_args args = {
+		.errp			= &err,
+		.path			= path,
+		.ia			= ia,
+		.delegated_inode	= delegated_inode
+	};
+
+	call_notify_change(&args);
+
+	return err;
+}
+
+int vfsub_sio_notify_change(struct path *path, struct iattr *ia,
+			    struct inode **delegated_inode)
+{
+	int err, wkq_err;
+	struct notify_change_args args = {
+		.errp			= &err,
+		.path			= path,
+		.ia			= ia,
+		.delegated_inode	= delegated_inode
+	};
+
+	wkq_err = au_wkq_wait(call_notify_change, &args);
+	if (unlikely(wkq_err))
+		err = wkq_err;
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct unlink_args {
+	int *errp;
+	struct inode *dir;
+	struct path *path;
+	struct inode **delegated_inode;
+};
+
+static void call_unlink(void *args)
+{
+	struct unlink_args *a = args;
+	struct dentry *d = a->path->dentry;
+	struct inode *h_inode;
+	struct user_namespace *userns;
+	const int stop_sillyrename = (au_test_nfs(d->d_sb)
+				      && au_dcount(d) == 1);
+
+	IMustLock(a->dir);
+
+	a->path->dentry = d->d_parent;
+	*a->errp = security_path_unlink(a->path, d);
+	a->path->dentry = d;
+	if (unlikely(*a->errp))
+		return;
+
+	if (!stop_sillyrename)
+		dget(d);
+	h_inode = NULL;
+	if (d_is_positive(d)) {
+		h_inode = d_inode(d);
+		ihold(h_inode);
+	}
+
+	userns = mnt_user_ns(a->path->mnt);
+	lockdep_off();
+	*a->errp = vfs_unlink(userns, a->dir, d, a->delegated_inode);
+	lockdep_on();
+	if (!*a->errp) {
+		struct path tmp = {
+			.dentry = d->d_parent,
+			.mnt	= a->path->mnt
+		};
+		vfsub_update_h_iattr(&tmp, /*did*/NULL); /*ignore*/
+	}
+
+	if (!stop_sillyrename)
+		dput(d);
+	if (h_inode)
+		iput(h_inode);
+
+	AuTraceErr(*a->errp);
+}
+
+/*
+ * @dir: must be locked.
+ * @dentry: target dentry.
+ */
+int vfsub_unlink(struct inode *dir, struct path *path,
+		 struct inode **delegated_inode, int force)
+{
+	int err;
+	struct unlink_args args = {
+		.errp			= &err,
+		.dir			= dir,
+		.path			= path,
+		.delegated_inode	= delegated_inode
+	};
+
+	if (!force)
+		call_unlink(&args);
+	else {
+		int wkq_err;
+
+		wkq_err = au_wkq_wait(call_unlink, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/vfsub.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/vfsub.h
@@ -0,0 +1,358 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * sub-routines for VFS
+ */
+
+#ifndef __AUFS_VFSUB_H__
+#define __AUFS_VFSUB_H__
+
+#ifdef __KERNEL__
+
+#include <linux/fs.h>
+#include <linux/mount.h>
+#include <linux/posix_acl.h>
+#include <linux/xattr.h>
+#include "debug.h"
+
+/* copied from linux/fs/internal.h */
+/* todo: BAD approach!! */
+extern void __mnt_drop_write(struct vfsmount *);
+extern struct file *alloc_empty_file(int, const struct cred *);
+
+/* ---------------------------------------------------------------------- */
+
+/* lock subclass for lower inode */
+/* default MAX_LOCKDEP_SUBCLASSES(8) is not enough */
+/* reduce? gave up. */
+enum {
+	AuLsc_I_Begin = I_MUTEX_PARENT2, /* 5 */
+	AuLsc_I_PARENT,		/* lower inode, parent first */
+	AuLsc_I_PARENT2,	/* copyup dirs */
+	AuLsc_I_PARENT3,	/* copyup wh */
+	AuLsc_I_CHILD,
+	AuLsc_I_CHILD2,
+	AuLsc_I_End
+};
+
+/* to debug easier, do not make them inlined functions */
+#define MtxMustLock(mtx)	AuDebugOn(!mutex_is_locked(mtx))
+#define IMustLock(i)		AuDebugOn(!inode_is_locked(i))
+
+/* ---------------------------------------------------------------------- */
+
+static inline void vfsub_drop_nlink(struct inode *inode)
+{
+	AuDebugOn(!inode->i_nlink);
+	drop_nlink(inode);
+}
+
+static inline void vfsub_dead_dir(struct inode *inode)
+{
+	AuDebugOn(!S_ISDIR(inode->i_mode));
+	inode->i_flags |= S_DEAD;
+	clear_nlink(inode);
+}
+
+static inline int vfsub_native_ro(struct inode *inode)
+{
+	return sb_rdonly(inode->i_sb)
+		|| IS_RDONLY(inode)
+		/* || IS_APPEND(inode) */
+		|| IS_IMMUTABLE(inode);
+}
+
+#ifdef CONFIG_AUFS_BR_FUSE
+int vfsub_test_mntns(struct vfsmount *mnt, struct super_block *h_sb);
+#else
+AuStubInt0(vfsub_test_mntns, struct vfsmount *mnt, struct super_block *h_sb);
+#endif
+
+int vfsub_sync_filesystem(struct super_block *h_sb, int wait);
+
+/* ---------------------------------------------------------------------- */
+
+int vfsub_update_h_iattr(struct path *h_path, int *did);
+struct file *vfsub_dentry_open(struct path *path, int flags);
+struct file *vfsub_filp_open(const char *path, int oflags, int mode);
+struct au_branch;
+struct vfsub_aopen_args {
+	struct file		*file;
+	unsigned int		open_flag;
+	umode_t			create_mode;
+	struct au_branch	*br;
+};
+int vfsub_atomic_open(struct inode *dir, struct dentry *dentry,
+		      struct vfsub_aopen_args *args);
+int vfsub_kern_path(const char *name, unsigned int flags, struct path *path);
+
+struct dentry *vfsub_lookup_one_len_unlocked(const char *name,
+					     struct path *ppath, int len);
+struct dentry *vfsub_lookup_one_len(const char *name, struct path *ppath,
+				    int len);
+
+struct vfsub_lkup_one_args {
+	struct dentry **errp;
+	struct qstr *name;
+	struct path *ppath;
+};
+
+static inline struct dentry *vfsub_lkup_one(struct qstr *name,
+					    struct path *ppath)
+{
+	return vfsub_lookup_one_len(name->name, ppath, name->len);
+}
+
+void vfsub_call_lkup_one(void *args);
+
+/* ---------------------------------------------------------------------- */
+
+static inline int vfsub_mnt_want_write(struct vfsmount *mnt)
+{
+	int err;
+
+	lockdep_off();
+	err = mnt_want_write(mnt);
+	lockdep_on();
+	return err;
+}
+
+static inline void vfsub_mnt_drop_write(struct vfsmount *mnt)
+{
+	lockdep_off();
+	mnt_drop_write(mnt);
+	lockdep_on();
+}
+
+#if 0 /* reserved */
+static inline void vfsub_mnt_drop_write_file(struct file *file)
+{
+	lockdep_off();
+	mnt_drop_write_file(file);
+	lockdep_on();
+}
+#endif
+
+/* ---------------------------------------------------------------------- */
+
+struct au_hinode;
+struct dentry *vfsub_lock_rename(struct dentry *d1, struct au_hinode *hdir1,
+				 struct dentry *d2, struct au_hinode *hdir2);
+void vfsub_unlock_rename(struct dentry *d1, struct au_hinode *hdir1,
+			 struct dentry *d2, struct au_hinode *hdir2);
+
+int vfsub_create(struct inode *dir, struct path *path, int mode,
+		 bool want_excl);
+int vfsub_symlink(struct inode *dir, struct path *path,
+		  const char *symname);
+int vfsub_mknod(struct inode *dir, struct path *path, int mode, dev_t dev);
+int vfsub_link(struct dentry *src_dentry, struct inode *dir,
+	       struct path *path, struct inode **delegated_inode);
+int vfsub_rename(struct inode *src_hdir, struct dentry *src_dentry,
+		 struct inode *hdir, struct path *path,
+		 struct inode **delegated_inode, unsigned int flags);
+int vfsub_mkdir(struct inode *dir, struct path *path, int mode);
+int vfsub_rmdir(struct inode *dir, struct path *path);
+
+/* ---------------------------------------------------------------------- */
+
+ssize_t vfsub_read_u(struct file *file, char __user *ubuf, size_t count,
+		     loff_t *ppos);
+ssize_t vfsub_read_k(struct file *file, void *kbuf, size_t count,
+			loff_t *ppos);
+ssize_t vfsub_write_u(struct file *file, const char __user *ubuf, size_t count,
+		      loff_t *ppos);
+ssize_t vfsub_write_k(struct file *file, void *kbuf, size_t count,
+		      loff_t *ppos);
+int vfsub_flush(struct file *file, fl_owner_t id);
+int vfsub_iterate_dir(struct file *file, struct dir_context *ctx);
+
+static inline loff_t vfsub_f_size_read(struct file *file)
+{
+	return i_size_read(file_inode(file));
+}
+
+static inline unsigned int vfsub_file_flags(struct file *file)
+{
+	unsigned int flags;
+
+	spin_lock(&file->f_lock);
+	flags = file->f_flags;
+	spin_unlock(&file->f_lock);
+
+	return flags;
+}
+
+static inline int vfsub_file_execed(struct file *file)
+{
+	/* todo: direct access f_flags */
+	return !!(vfsub_file_flags(file) & __FMODE_EXEC);
+}
+
+#if 0 /* reserved */
+static inline void vfsub_file_accessed(struct file *h_file)
+{
+	file_accessed(h_file);
+	vfsub_update_h_iattr(&h_file->f_path, /*did*/NULL); /*ignore*/
+}
+#endif
+
+#if 0 /* reserved */
+static inline void vfsub_touch_atime(struct vfsmount *h_mnt,
+				     struct dentry *h_dentry)
+{
+	struct path h_path = {
+		.dentry	= h_dentry,
+		.mnt	= h_mnt
+	};
+	touch_atime(&h_path);
+	vfsub_update_h_iattr(&h_path, /*did*/NULL); /*ignore*/
+}
+#endif
+
+static inline int vfsub_update_time(struct inode *h_inode,
+				    struct timespec64 *ts, int flags)
+{
+	return inode_update_time(h_inode, ts, flags);
+	/* no vfsub_update_h_iattr() since we don't have struct path */
+}
+
+#ifdef CONFIG_FS_POSIX_ACL
+static inline int vfsub_acl_chmod(struct user_namespace *h_userns,
+				  struct inode *h_inode, umode_t h_mode)
+{
+	int err;
+
+	err = posix_acl_chmod(h_userns, h_inode, h_mode);
+	if (err == -EOPNOTSUPP)
+		err = 0;
+	return err;
+}
+#else
+AuStubInt0(vfsub_acl_chmod, struct user_namespace *h_userns,
+	   struct inode *h_inode, umode_t h_mode);
+#endif
+
+long vfsub_splice_to(struct file *in, loff_t *ppos,
+		     struct pipe_inode_info *pipe, size_t len,
+		     unsigned int flags);
+long vfsub_splice_from(struct pipe_inode_info *pipe, struct file *out,
+		       loff_t *ppos, size_t len, unsigned int flags);
+
+static inline long vfsub_truncate(struct path *path, loff_t length)
+{
+	long err;
+
+	lockdep_off();
+	err = vfs_truncate(path, length);
+	lockdep_on();
+	return err;
+}
+
+int vfsub_trunc(struct path *h_path, loff_t length, unsigned int attr,
+		struct file *h_file);
+int vfsub_fsync(struct file *file, struct path *path, int datasync);
+
+/*
+ * re-use branch fs's ioctl(FICLONE) while aufs itself doesn't support such
+ * ioctl.
+ */
+static inline loff_t vfsub_clone_file_range(struct file *src, struct file *dst,
+					    loff_t len)
+{
+	loff_t err;
+
+	lockdep_off();
+	err = vfs_clone_file_range(src, 0, dst, 0, len, /*remap_flags*/0);
+	lockdep_on();
+
+	return err;
+}
+
+/* copy_file_range(2) is a systemcall */
+static inline ssize_t vfsub_copy_file_range(struct file *src, loff_t src_pos,
+					    struct file *dst, loff_t dst_pos,
+					    size_t len, unsigned int flags)
+{
+	ssize_t ssz;
+
+	lockdep_off();
+	ssz = vfs_copy_file_range(src, src_pos, dst, dst_pos, len, flags);
+	lockdep_on();
+
+	return ssz;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static inline loff_t vfsub_llseek(struct file *file, loff_t offset, int origin)
+{
+	loff_t err;
+
+	lockdep_off();
+	err = vfs_llseek(file, offset, origin);
+	lockdep_on();
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int vfsub_sio_mkdir(struct inode *dir, struct path *path, int mode);
+int vfsub_sio_rmdir(struct inode *dir, struct path *path);
+int vfsub_sio_notify_change(struct path *path, struct iattr *ia,
+			    struct inode **delegated_inode);
+int vfsub_notify_change(struct path *path, struct iattr *ia,
+			struct inode **delegated_inode);
+int vfsub_unlink(struct inode *dir, struct path *path,
+		 struct inode **delegated_inode, int force);
+
+static inline int vfsub_getattr(const struct path *path, struct kstat *st)
+{
+	return vfs_getattr(path, st, STATX_BASIC_STATS, AT_STATX_SYNC_AS_STAT);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static inline int vfsub_setxattr(struct user_namespace *userns,
+				 struct dentry *dentry, const char *name,
+				 const void *value, size_t size, int flags)
+{
+	int err;
+
+	lockdep_off();
+	err = vfs_setxattr(userns, dentry, name, value, size, flags);
+	lockdep_on();
+
+	return err;
+}
+
+static inline int vfsub_removexattr(struct user_namespace *userns,
+				    struct dentry *dentry, const char *name)
+{
+	int err;
+
+	lockdep_off();
+	err = vfs_removexattr(userns, dentry, name);
+	lockdep_on();
+
+	return err;
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_VFSUB_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/wbr_policy.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/wbr_policy.c
@@ -0,0 +1,830 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * policies for selecting one among multiple writable branches
+ */
+
+#include <linux/statfs.h>
+#include "aufs.h"
+
+/* subset of cpup_attr() */
+static noinline_for_stack
+int au_cpdown_attr(struct path *h_path, struct dentry *h_src)
+{
+	int err, sbits;
+	struct iattr ia;
+	struct inode *h_isrc;
+
+	h_isrc = d_inode(h_src);
+	ia.ia_valid = ATTR_FORCE | ATTR_MODE | ATTR_UID | ATTR_GID;
+	ia.ia_mode = h_isrc->i_mode;
+	ia.ia_uid = h_isrc->i_uid;
+	ia.ia_gid = h_isrc->i_gid;
+	sbits = !!(ia.ia_mode & (S_ISUID | S_ISGID));
+	au_cpup_attr_flags(d_inode(h_path->dentry), h_isrc->i_flags);
+	/* no delegation since it is just created */
+	err = vfsub_sio_notify_change(h_path, &ia, /*delegated*/NULL);
+
+	/* is this nfs only? */
+	if (!err && sbits && au_test_nfs(h_path->dentry->d_sb)) {
+		ia.ia_valid = ATTR_FORCE | ATTR_MODE;
+		ia.ia_mode = h_isrc->i_mode;
+		err = vfsub_sio_notify_change(h_path, &ia, /*delegated*/NULL);
+	}
+
+	return err;
+}
+
+#define AuCpdown_PARENT_OPQ	1
+#define AuCpdown_WHED		(1 << 1)
+#define AuCpdown_MADE_DIR	(1 << 2)
+#define AuCpdown_DIROPQ		(1 << 3)
+#define au_ftest_cpdown(flags, name)	((flags) & AuCpdown_##name)
+#define au_fset_cpdown(flags, name) \
+	do { (flags) |= AuCpdown_##name; } while (0)
+#define au_fclr_cpdown(flags, name) \
+	do { (flags) &= ~AuCpdown_##name; } while (0)
+
+static int au_cpdown_dir_opq(struct dentry *dentry, aufs_bindex_t bdst,
+			     unsigned int *flags)
+{
+	int err;
+	struct dentry *opq_dentry;
+
+	opq_dentry = au_diropq_create(dentry, bdst);
+	err = PTR_ERR(opq_dentry);
+	if (IS_ERR(opq_dentry))
+		goto out;
+	dput(opq_dentry);
+	au_fset_cpdown(*flags, DIROPQ);
+
+out:
+	return err;
+}
+
+static int au_cpdown_dir_wh(struct dentry *dentry, struct dentry *h_parent,
+			    struct inode *dir, aufs_bindex_t bdst)
+{
+	int err;
+	struct path h_path;
+	struct au_branch *br;
+
+	br = au_sbr(dentry->d_sb, bdst);
+	h_path.dentry = au_wh_lkup(h_parent, &dentry->d_name, br);
+	err = PTR_ERR(h_path.dentry);
+	if (IS_ERR(h_path.dentry))
+		goto out;
+
+	err = 0;
+	if (d_is_positive(h_path.dentry)) {
+		h_path.mnt = au_br_mnt(br);
+		err = au_wh_unlink_dentry(au_h_iptr(dir, bdst), &h_path,
+					  dentry);
+	}
+	dput(h_path.dentry);
+
+out:
+	return err;
+}
+
+static int au_cpdown_dir(struct dentry *dentry, aufs_bindex_t bdst,
+			 struct au_pin *pin,
+			 struct dentry *h_parent, void *arg)
+{
+	int err, rerr;
+	aufs_bindex_t bopq, btop;
+	struct path h_path;
+	struct dentry *parent;
+	struct inode *h_dir, *h_inode, *inode, *dir;
+	unsigned int *flags = arg;
+
+	btop = au_dbtop(dentry);
+	/* dentry is di-locked */
+	parent = dget_parent(dentry);
+	dir = d_inode(parent);
+	h_dir = d_inode(h_parent);
+	AuDebugOn(h_dir != au_h_iptr(dir, bdst));
+	IMustLock(h_dir);
+
+	err = au_lkup_neg(dentry, bdst, /*wh*/0);
+	if (unlikely(err < 0))
+		goto out;
+	h_path.dentry = au_h_dptr(dentry, bdst);
+	h_path.mnt = au_sbr_mnt(dentry->d_sb, bdst);
+	err = vfsub_sio_mkdir(au_h_iptr(dir, bdst), &h_path, 0755);
+	if (unlikely(err))
+		goto out_put;
+	au_fset_cpdown(*flags, MADE_DIR);
+
+	bopq = au_dbdiropq(dentry);
+	au_fclr_cpdown(*flags, WHED);
+	au_fclr_cpdown(*flags, DIROPQ);
+	if (au_dbwh(dentry) == bdst)
+		au_fset_cpdown(*flags, WHED);
+	if (!au_ftest_cpdown(*flags, PARENT_OPQ) && bopq <= bdst)
+		au_fset_cpdown(*flags, PARENT_OPQ);
+	h_inode = d_inode(h_path.dentry);
+	inode_lock_nested(h_inode, AuLsc_I_CHILD);
+	if (au_ftest_cpdown(*flags, WHED)) {
+		err = au_cpdown_dir_opq(dentry, bdst, flags);
+		if (unlikely(err)) {
+			inode_unlock(h_inode);
+			goto out_dir;
+		}
+	}
+
+	err = au_cpdown_attr(&h_path, au_h_dptr(dentry, btop));
+	inode_unlock(h_inode);
+	if (unlikely(err))
+		goto out_opq;
+
+	if (au_ftest_cpdown(*flags, WHED)) {
+		err = au_cpdown_dir_wh(dentry, h_parent, dir, bdst);
+		if (unlikely(err))
+			goto out_opq;
+	}
+
+	inode = d_inode(dentry);
+	if (au_ibbot(inode) < bdst)
+		au_set_ibbot(inode, bdst);
+	au_set_h_iptr(inode, bdst, au_igrab(h_inode),
+		      au_hi_flags(inode, /*isdir*/1));
+	au_fhsm_wrote(dentry->d_sb, bdst, /*force*/0);
+	goto out; /* success */
+
+	/* revert */
+out_opq:
+	if (au_ftest_cpdown(*flags, DIROPQ)) {
+		inode_lock_nested(h_inode, AuLsc_I_CHILD);
+		rerr = au_diropq_remove(dentry, bdst);
+		inode_unlock(h_inode);
+		if (unlikely(rerr)) {
+			AuIOErr("failed removing diropq for %pd b%d (%d)\n",
+				dentry, bdst, rerr);
+			err = -EIO;
+			goto out;
+		}
+	}
+out_dir:
+	if (au_ftest_cpdown(*flags, MADE_DIR)) {
+		rerr = vfsub_sio_rmdir(au_h_iptr(dir, bdst), &h_path);
+		if (unlikely(rerr)) {
+			AuIOErr("failed removing %pd b%d (%d)\n",
+				dentry, bdst, rerr);
+			err = -EIO;
+		}
+	}
+out_put:
+	au_set_h_dptr(dentry, bdst, NULL);
+	if (au_dbbot(dentry) == bdst)
+		au_update_dbbot(dentry);
+out:
+	dput(parent);
+	return err;
+}
+
+int au_cpdown_dirs(struct dentry *dentry, aufs_bindex_t bdst)
+{
+	int err;
+	unsigned int flags;
+
+	flags = 0;
+	err = au_cp_dirs(dentry, bdst, au_cpdown_dir, &flags);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* policies for create */
+
+int au_wbr_nonopq(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	int err, i, j, ndentry;
+	aufs_bindex_t bopq;
+	struct au_dcsub_pages dpages;
+	struct au_dpage *dpage;
+	struct dentry **dentries, *parent, *d;
+
+	err = au_dpages_init(&dpages, GFP_NOFS);
+	if (unlikely(err))
+		goto out;
+	parent = dget_parent(dentry);
+	err = au_dcsub_pages_rev_aufs(&dpages, parent, /*do_include*/0);
+	if (unlikely(err))
+		goto out_free;
+
+	err = bindex;
+	for (i = 0; i < dpages.ndpage; i++) {
+		dpage = dpages.dpages + i;
+		dentries = dpage->dentries;
+		ndentry = dpage->ndentry;
+		for (j = 0; j < ndentry; j++) {
+			d = dentries[j];
+			di_read_lock_parent2(d, !AuLock_IR);
+			bopq = au_dbdiropq(d);
+			di_read_unlock(d, !AuLock_IR);
+			if (bopq >= 0 && bopq < err)
+				err = bopq;
+		}
+	}
+
+out_free:
+	dput(parent);
+	au_dpages_free(&dpages);
+out:
+	return err;
+}
+
+static int au_wbr_bu(struct super_block *sb, aufs_bindex_t bindex)
+{
+	for (; bindex >= 0; bindex--)
+		if (!au_br_rdonly(au_sbr(sb, bindex)))
+			return bindex;
+	return -EROFS;
+}
+
+/* top down parent */
+static int au_wbr_create_tdp(struct dentry *dentry,
+			     unsigned int flags __maybe_unused)
+{
+	int err;
+	aufs_bindex_t btop, bindex;
+	struct super_block *sb;
+	struct dentry *parent, *h_parent;
+
+	sb = dentry->d_sb;
+	btop = au_dbtop(dentry);
+	err = btop;
+	if (!au_br_rdonly(au_sbr(sb, btop)))
+		goto out;
+
+	err = -EROFS;
+	parent = dget_parent(dentry);
+	for (bindex = au_dbtop(parent); bindex < btop; bindex++) {
+		h_parent = au_h_dptr(parent, bindex);
+		if (!h_parent || d_is_negative(h_parent))
+			continue;
+
+		if (!au_br_rdonly(au_sbr(sb, bindex))) {
+			err = bindex;
+			break;
+		}
+	}
+	dput(parent);
+
+	/* bottom up here */
+	if (unlikely(err < 0)) {
+		err = au_wbr_bu(sb, btop - 1);
+		if (err >= 0)
+			err = au_wbr_nonopq(dentry, err);
+	}
+
+out:
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* an exception for the policy other than tdp */
+static int au_wbr_create_exp(struct dentry *dentry)
+{
+	int err;
+	aufs_bindex_t bwh, bdiropq;
+	struct dentry *parent;
+
+	err = -1;
+	bwh = au_dbwh(dentry);
+	parent = dget_parent(dentry);
+	bdiropq = au_dbdiropq(parent);
+	if (bwh >= 0) {
+		if (bdiropq >= 0)
+			err = min(bdiropq, bwh);
+		else
+			err = bwh;
+		AuDbg("%d\n", err);
+	} else if (bdiropq >= 0) {
+		err = bdiropq;
+		AuDbg("%d\n", err);
+	}
+	dput(parent);
+
+	if (err >= 0)
+		err = au_wbr_nonopq(dentry, err);
+
+	if (err >= 0 && au_br_rdonly(au_sbr(dentry->d_sb, err)))
+		err = -1;
+
+	AuDbg("%d\n", err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* round robin */
+static int au_wbr_create_init_rr(struct super_block *sb)
+{
+	int err;
+
+	err = au_wbr_bu(sb, au_sbbot(sb));
+	atomic_set(&au_sbi(sb)->si_wbr_rr_next, -err); /* less important */
+	/* smp_mb(); */
+
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+static int au_wbr_create_rr(struct dentry *dentry, unsigned int flags)
+{
+	int err, nbr;
+	unsigned int u;
+	aufs_bindex_t bindex, bbot;
+	struct super_block *sb;
+	atomic_t *next;
+
+	err = au_wbr_create_exp(dentry);
+	if (err >= 0)
+		goto out;
+
+	sb = dentry->d_sb;
+	next = &au_sbi(sb)->si_wbr_rr_next;
+	bbot = au_sbbot(sb);
+	nbr = bbot + 1;
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		if (!au_ftest_wbr(flags, DIR)) {
+			err = atomic_dec_return(next) + 1;
+			/* modulo for 0 is meaningless */
+			if (unlikely(!err))
+				err = atomic_dec_return(next) + 1;
+		} else
+			err = atomic_read(next);
+		AuDbg("%d\n", err);
+		u = err;
+		err = u % nbr;
+		AuDbg("%d\n", err);
+		if (!au_br_rdonly(au_sbr(sb, err)))
+			break;
+		err = -EROFS;
+	}
+
+	if (err >= 0)
+		err = au_wbr_nonopq(dentry, err);
+
+out:
+	AuDbg("%d\n", err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* most free space */
+static void au_mfs(struct dentry *dentry, struct dentry *parent)
+{
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_wbr_mfs *mfs;
+	struct dentry *h_parent;
+	aufs_bindex_t bindex, bbot;
+	int err;
+	unsigned long long b, bavail;
+	struct path h_path;
+	/* reduce the stack usage */
+	struct kstatfs *st;
+
+	st = kmalloc(sizeof(*st), GFP_NOFS);
+	if (unlikely(!st)) {
+		AuWarn1("failed updating mfs(%d), ignored\n", -ENOMEM);
+		return;
+	}
+
+	bavail = 0;
+	sb = dentry->d_sb;
+	mfs = &au_sbi(sb)->si_wbr_mfs;
+	MtxMustLock(&mfs->mfs_lock);
+	mfs->mfs_bindex = -EROFS;
+	mfs->mfsrr_bytes = 0;
+	if (!parent) {
+		bindex = 0;
+		bbot = au_sbbot(sb);
+	} else {
+		bindex = au_dbtop(parent);
+		bbot = au_dbtaildir(parent);
+	}
+
+	for (; bindex <= bbot; bindex++) {
+		if (parent) {
+			h_parent = au_h_dptr(parent, bindex);
+			if (!h_parent || d_is_negative(h_parent))
+				continue;
+		}
+		br = au_sbr(sb, bindex);
+		if (au_br_rdonly(br))
+			continue;
+
+		/* sb->s_root for NFS is unreliable */
+		h_path.mnt = au_br_mnt(br);
+		h_path.dentry = h_path.mnt->mnt_root;
+		err = vfs_statfs(&h_path, st);
+		if (unlikely(err)) {
+			AuWarn1("failed statfs, b%d, %d\n", bindex, err);
+			continue;
+		}
+
+		/* when the available size is equal, select the lower one */
+		BUILD_BUG_ON(sizeof(b) < sizeof(st->f_bavail)
+			     || sizeof(b) < sizeof(st->f_bsize));
+		b = st->f_bavail * st->f_bsize;
+		br->br_wbr->wbr_bytes = b;
+		if (b >= bavail) {
+			bavail = b;
+			mfs->mfs_bindex = bindex;
+			mfs->mfs_jiffy = jiffies;
+		}
+	}
+
+	mfs->mfsrr_bytes = bavail;
+	AuDbg("b%d\n", mfs->mfs_bindex);
+	au_kfree_rcu(st);
+}
+
+static int au_wbr_create_mfs(struct dentry *dentry, unsigned int flags)
+{
+	int err;
+	struct dentry *parent;
+	struct super_block *sb;
+	struct au_wbr_mfs *mfs;
+
+	err = au_wbr_create_exp(dentry);
+	if (err >= 0)
+		goto out;
+
+	sb = dentry->d_sb;
+	parent = NULL;
+	if (au_ftest_wbr(flags, PARENT))
+		parent = dget_parent(dentry);
+	mfs = &au_sbi(sb)->si_wbr_mfs;
+	mutex_lock(&mfs->mfs_lock);
+	if (time_after(jiffies, mfs->mfs_jiffy + mfs->mfs_expire)
+	    || mfs->mfs_bindex < 0
+	    || au_br_rdonly(au_sbr(sb, mfs->mfs_bindex)))
+		au_mfs(dentry, parent);
+	mutex_unlock(&mfs->mfs_lock);
+	err = mfs->mfs_bindex;
+	dput(parent);
+
+	if (err >= 0)
+		err = au_wbr_nonopq(dentry, err);
+
+out:
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+static int au_wbr_create_init_mfs(struct super_block *sb)
+{
+	struct au_wbr_mfs *mfs;
+
+	mfs = &au_sbi(sb)->si_wbr_mfs;
+	mutex_init(&mfs->mfs_lock);
+	mfs->mfs_jiffy = 0;
+	mfs->mfs_bindex = -EROFS;
+
+	return 0;
+}
+
+static int au_wbr_create_fin_mfs(struct super_block *sb __maybe_unused)
+{
+	mutex_destroy(&au_sbi(sb)->si_wbr_mfs.mfs_lock);
+	return 0;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* top down regardless parent, and then mfs */
+static int au_wbr_create_tdmfs(struct dentry *dentry,
+			       unsigned int flags __maybe_unused)
+{
+	int err;
+	aufs_bindex_t bwh, btail, bindex, bfound, bmfs;
+	unsigned long long watermark;
+	struct super_block *sb;
+	struct au_wbr_mfs *mfs;
+	struct au_branch *br;
+	struct dentry *parent;
+
+	sb = dentry->d_sb;
+	mfs = &au_sbi(sb)->si_wbr_mfs;
+	mutex_lock(&mfs->mfs_lock);
+	if (time_after(jiffies, mfs->mfs_jiffy + mfs->mfs_expire)
+	    || mfs->mfs_bindex < 0)
+		au_mfs(dentry, /*parent*/NULL);
+	watermark = mfs->mfsrr_watermark;
+	bmfs = mfs->mfs_bindex;
+	mutex_unlock(&mfs->mfs_lock);
+
+	/* another style of au_wbr_create_exp() */
+	bwh = au_dbwh(dentry);
+	parent = dget_parent(dentry);
+	btail = au_dbtaildir(parent);
+	if (bwh >= 0 && bwh < btail)
+		btail = bwh;
+
+	err = au_wbr_nonopq(dentry, btail);
+	if (unlikely(err < 0))
+		goto out;
+	btail = err;
+	bfound = -1;
+	for (bindex = 0; bindex <= btail; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (au_br_rdonly(br))
+			continue;
+		if (br->br_wbr->wbr_bytes > watermark) {
+			bfound = bindex;
+			break;
+		}
+	}
+	err = bfound;
+	if (err < 0)
+		err = bmfs;
+
+out:
+	dput(parent);
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* most free space and then round robin */
+static int au_wbr_create_mfsrr(struct dentry *dentry, unsigned int flags)
+{
+	int err;
+	struct au_wbr_mfs *mfs;
+
+	err = au_wbr_create_mfs(dentry, flags);
+	if (err >= 0) {
+		mfs = &au_sbi(dentry->d_sb)->si_wbr_mfs;
+		mutex_lock(&mfs->mfs_lock);
+		if (mfs->mfsrr_bytes < mfs->mfsrr_watermark)
+			err = au_wbr_create_rr(dentry, flags);
+		mutex_unlock(&mfs->mfs_lock);
+	}
+
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+static int au_wbr_create_init_mfsrr(struct super_block *sb)
+{
+	int err;
+
+	au_wbr_create_init_mfs(sb); /* ignore */
+	err = au_wbr_create_init_rr(sb);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* top down parent and most free space */
+static int au_wbr_create_pmfs(struct dentry *dentry, unsigned int flags)
+{
+	int err, e2;
+	unsigned long long b;
+	aufs_bindex_t bindex, btop, bbot;
+	struct super_block *sb;
+	struct dentry *parent, *h_parent;
+	struct au_branch *br;
+
+	err = au_wbr_create_tdp(dentry, flags);
+	if (unlikely(err < 0))
+		goto out;
+	parent = dget_parent(dentry);
+	btop = au_dbtop(parent);
+	bbot = au_dbtaildir(parent);
+	if (btop == bbot)
+		goto out_parent; /* success */
+
+	e2 = au_wbr_create_mfs(dentry, flags);
+	if (e2 < 0)
+		goto out_parent; /* success */
+
+	/* when the available size is equal, select upper one */
+	sb = dentry->d_sb;
+	br = au_sbr(sb, err);
+	b = br->br_wbr->wbr_bytes;
+	AuDbg("b%d, %llu\n", err, b);
+
+	for (bindex = btop; bindex <= bbot; bindex++) {
+		h_parent = au_h_dptr(parent, bindex);
+		if (!h_parent || d_is_negative(h_parent))
+			continue;
+
+		br = au_sbr(sb, bindex);
+		if (!au_br_rdonly(br) && br->br_wbr->wbr_bytes > b) {
+			b = br->br_wbr->wbr_bytes;
+			err = bindex;
+			AuDbg("b%d, %llu\n", err, b);
+		}
+	}
+
+	if (err >= 0)
+		err = au_wbr_nonopq(dentry, err);
+
+out_parent:
+	dput(parent);
+out:
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * - top down parent
+ * - most free space with parent
+ * - most free space round-robin regardless parent
+ */
+static int au_wbr_create_pmfsrr(struct dentry *dentry, unsigned int flags)
+{
+	int err;
+	unsigned long long watermark;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_wbr_mfs *mfs;
+
+	err = au_wbr_create_pmfs(dentry, flags | AuWbr_PARENT);
+	if (unlikely(err < 0))
+		goto out;
+
+	sb = dentry->d_sb;
+	br = au_sbr(sb, err);
+	mfs = &au_sbi(sb)->si_wbr_mfs;
+	mutex_lock(&mfs->mfs_lock);
+	watermark = mfs->mfsrr_watermark;
+	mutex_unlock(&mfs->mfs_lock);
+	if (br->br_wbr->wbr_bytes < watermark)
+		/* regardless the parent dir */
+		err = au_wbr_create_mfsrr(dentry, flags);
+
+out:
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* policies for copyup */
+
+/* top down parent */
+static int au_wbr_copyup_tdp(struct dentry *dentry)
+{
+	return au_wbr_create_tdp(dentry, /*flags, anything is ok*/0);
+}
+
+/* bottom up parent */
+static int au_wbr_copyup_bup(struct dentry *dentry)
+{
+	int err;
+	aufs_bindex_t bindex, btop;
+	struct dentry *parent, *h_parent;
+	struct super_block *sb;
+
+	err = -EROFS;
+	sb = dentry->d_sb;
+	parent = dget_parent(dentry);
+	btop = au_dbtop(parent);
+	for (bindex = au_dbtop(dentry); bindex >= btop; bindex--) {
+		h_parent = au_h_dptr(parent, bindex);
+		if (!h_parent || d_is_negative(h_parent))
+			continue;
+
+		if (!au_br_rdonly(au_sbr(sb, bindex))) {
+			err = bindex;
+			break;
+		}
+	}
+	dput(parent);
+
+	/* bottom up here */
+	if (unlikely(err < 0))
+		err = au_wbr_bu(sb, btop - 1);
+
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+/* bottom up */
+int au_wbr_do_copyup_bu(struct dentry *dentry, aufs_bindex_t btop)
+{
+	int err;
+
+	err = au_wbr_bu(dentry->d_sb, btop);
+	AuDbg("b%d\n", err);
+	if (err > btop)
+		err = au_wbr_nonopq(dentry, err);
+
+	AuDbg("b%d\n", err);
+	return err;
+}
+
+static int au_wbr_copyup_bu(struct dentry *dentry)
+{
+	int err;
+	aufs_bindex_t btop;
+
+	btop = au_dbtop(dentry);
+	err = au_wbr_do_copyup_bu(dentry, btop);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_wbr_copyup_operations au_wbr_copyup_ops[] = {
+	[AuWbrCopyup_TDP] = {
+		.copyup	= au_wbr_copyup_tdp
+	},
+	[AuWbrCopyup_BUP] = {
+		.copyup	= au_wbr_copyup_bup
+	},
+	[AuWbrCopyup_BU] = {
+		.copyup	= au_wbr_copyup_bu
+	}
+};
+
+struct au_wbr_create_operations au_wbr_create_ops[] = {
+	[AuWbrCreate_TDP] = {
+		.create	= au_wbr_create_tdp
+	},
+	[AuWbrCreate_RR] = {
+		.create	= au_wbr_create_rr,
+		.init	= au_wbr_create_init_rr
+	},
+	[AuWbrCreate_MFS] = {
+		.create	= au_wbr_create_mfs,
+		.init	= au_wbr_create_init_mfs,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_MFSV] = {
+		.create	= au_wbr_create_mfs,
+		.init	= au_wbr_create_init_mfs,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_MFSRR] = {
+		.create	= au_wbr_create_mfsrr,
+		.init	= au_wbr_create_init_mfsrr,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_MFSRRV] = {
+		.create	= au_wbr_create_mfsrr,
+		.init	= au_wbr_create_init_mfsrr,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_TDMFS] = {
+		.create	= au_wbr_create_tdmfs,
+		.init	= au_wbr_create_init_mfs,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_TDMFSV] = {
+		.create	= au_wbr_create_tdmfs,
+		.init	= au_wbr_create_init_mfs,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_PMFS] = {
+		.create	= au_wbr_create_pmfs,
+		.init	= au_wbr_create_init_mfs,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_PMFSV] = {
+		.create	= au_wbr_create_pmfs,
+		.init	= au_wbr_create_init_mfs,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_PMFSRR] = {
+		.create	= au_wbr_create_pmfsrr,
+		.init	= au_wbr_create_init_mfsrr,
+		.fin	= au_wbr_create_fin_mfs
+	},
+	[AuWbrCreate_PMFSRRV] = {
+		.create	= au_wbr_create_pmfsrr,
+		.init	= au_wbr_create_init_mfsrr,
+		.fin	= au_wbr_create_fin_mfs
+	}
+};
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/whout.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/whout.c
@@ -0,0 +1,1072 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * whiteout for logical deletion and opaque directory
+ */
+
+#include "aufs.h"
+
+#define WH_MASK			0444
+
+/*
+ * If a directory contains this file, then it is opaque.  We start with the
+ * .wh. flag so that it is blocked by lookup.
+ */
+static struct qstr diropq_name = QSTR_INIT(AUFS_WH_DIROPQ,
+					   sizeof(AUFS_WH_DIROPQ) - 1);
+
+/*
+ * generate whiteout name, which is NOT terminated by NULL.
+ * @name: original d_name.name
+ * @len: original d_name.len
+ * @wh: whiteout qstr
+ * returns zero when succeeds, otherwise error.
+ * succeeded value as wh->name should be freed by kfree().
+ */
+int au_wh_name_alloc(struct qstr *wh, const struct qstr *name)
+{
+	char *p;
+
+	if (unlikely(name->len > PATH_MAX - AUFS_WH_PFX_LEN))
+		return -ENAMETOOLONG;
+
+	wh->len = name->len + AUFS_WH_PFX_LEN;
+	p = kmalloc(wh->len, GFP_NOFS);
+	wh->name = p;
+	if (p) {
+		memcpy(p, AUFS_WH_PFX, AUFS_WH_PFX_LEN);
+		memcpy(p + AUFS_WH_PFX_LEN, name->name, name->len);
+		/* smp_mb(); */
+		return 0;
+	}
+	return -ENOMEM;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * test if the @wh_name exists under @h_ppath.
+ * @try_sio specifies the necessary of super-io.
+ */
+int au_wh_test(struct user_namespace *h_userns, struct path *h_ppath,
+	       struct qstr *wh_name, int try_sio)
+{
+	int err;
+	struct dentry *wh_dentry;
+
+	if (!try_sio)
+		wh_dentry = vfsub_lkup_one(wh_name, h_ppath);
+	else
+		wh_dentry = au_sio_lkup_one(h_userns, wh_name, h_ppath);
+	err = PTR_ERR(wh_dentry);
+	if (IS_ERR(wh_dentry)) {
+		if (err == -ENAMETOOLONG)
+			err = 0;
+		goto out;
+	}
+
+	err = 0;
+	if (d_is_negative(wh_dentry))
+		goto out_wh; /* success */
+
+	err = 1;
+	if (d_is_reg(wh_dentry))
+		goto out_wh; /* success */
+
+	err = -EIO;
+	AuIOErr("%pd Invalid whiteout entry type 0%o.\n",
+		wh_dentry, d_inode(wh_dentry)->i_mode);
+
+out_wh:
+	dput(wh_dentry);
+out:
+	return err;
+}
+
+/*
+ * test if the @h_path->dentry sets opaque or not.
+ */
+int au_diropq_test(struct user_namespace *h_userns, struct path *h_path)
+{
+	int err;
+	struct inode *h_dir;
+
+	h_dir = d_inode(h_path->dentry);
+	err = au_wh_test(h_userns, h_path, &diropq_name,
+			 au_test_h_perm_sio(h_userns, h_dir, MAY_EXEC));
+	return err;
+}
+
+/*
+ * returns a negative dentry whose name is unique and temporary.
+ */
+struct dentry *au_whtmp_lkup(struct dentry *h_parent, struct au_branch *br,
+			     struct qstr *prefix)
+{
+	struct dentry *dentry;
+	int i;
+	char defname[NAME_MAX - AUFS_MAX_NAMELEN + DNAME_INLINE_LEN + 1],
+		*name, *p;
+	/* strict atomic_t is unnecessary here */
+	static unsigned short cnt;
+	struct qstr qs;
+	struct path h_ppath;
+	struct user_namespace *h_userns;
+
+	BUILD_BUG_ON(sizeof(cnt) * 2 > AUFS_WH_TMP_LEN);
+
+	name = defname;
+	qs.len = sizeof(defname) - DNAME_INLINE_LEN + prefix->len - 1;
+	if (unlikely(prefix->len > DNAME_INLINE_LEN)) {
+		dentry = ERR_PTR(-ENAMETOOLONG);
+		if (unlikely(qs.len > NAME_MAX))
+			goto out;
+		dentry = ERR_PTR(-ENOMEM);
+		name = kmalloc(qs.len + 1, GFP_NOFS);
+		if (unlikely(!name))
+			goto out;
+	}
+
+	/* doubly whiteout-ed */
+	memcpy(name, AUFS_WH_PFX AUFS_WH_PFX, AUFS_WH_PFX_LEN * 2);
+	p = name + AUFS_WH_PFX_LEN * 2;
+	memcpy(p, prefix->name, prefix->len);
+	p += prefix->len;
+	*p++ = '.';
+	AuDebugOn(name + qs.len + 1 - p <= AUFS_WH_TMP_LEN);
+
+	h_ppath.dentry = h_parent;
+	h_ppath.mnt = au_br_mnt(br);
+	h_userns = au_br_userns(br);
+	qs.name = name;
+	for (i = 0; i < 3; i++) {
+		sprintf(p, "%.*x", AUFS_WH_TMP_LEN, cnt++);
+		dentry = au_sio_lkup_one(h_userns, &qs, &h_ppath);
+		if (IS_ERR(dentry) || d_is_negative(dentry))
+			goto out_name;
+		dput(dentry);
+	}
+	/* pr_warn("could not get random name\n"); */
+	dentry = ERR_PTR(-EEXIST);
+	AuDbg("%.*s\n", AuLNPair(&qs));
+	BUG();
+
+out_name:
+	if (name != defname)
+		au_kfree_try_rcu(name);
+out:
+	AuTraceErrPtr(dentry);
+	return dentry;
+}
+
+/*
+ * rename the @h_dentry on @br to the whiteouted temporary name.
+ */
+int au_whtmp_ren(struct dentry *h_dentry, struct au_branch *br)
+{
+	int err;
+	struct path h_path = {
+		.mnt = au_br_mnt(br)
+	};
+	struct inode *h_dir, *delegated;
+	struct dentry *h_parent;
+
+	h_parent = h_dentry->d_parent; /* dir inode is locked */
+	h_dir = d_inode(h_parent);
+	IMustLock(h_dir);
+
+	h_path.dentry = au_whtmp_lkup(h_parent, br, &h_dentry->d_name);
+	err = PTR_ERR(h_path.dentry);
+	if (IS_ERR(h_path.dentry))
+		goto out;
+
+	/* under the same dir, no need to lock_rename() */
+	delegated = NULL;
+	err = vfsub_rename(h_dir, h_dentry, h_dir, &h_path, &delegated,
+			   /*flags*/0);
+	AuTraceErr(err);
+	if (unlikely(err == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal rename\n");
+		iput(delegated);
+	}
+	dput(h_path.dentry);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * functions for removing a whiteout
+ */
+
+static int do_unlink_wh(struct inode *h_dir, struct path *h_path)
+{
+	int err, force;
+	struct inode *delegated;
+
+	/*
+	 * forces superio when the dir has a sticky bit.
+	 * this may be a violation of unix fs semantics.
+	 */
+	force = (h_dir->i_mode & S_ISVTX)
+		&& !uid_eq(current_fsuid(), d_inode(h_path->dentry)->i_uid);
+	delegated = NULL;
+	err = vfsub_unlink(h_dir, h_path, &delegated, force);
+	if (unlikely(err == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal unlink\n");
+		iput(delegated);
+	}
+	return err;
+}
+
+int au_wh_unlink_dentry(struct inode *h_dir, struct path *h_path,
+			struct dentry *dentry)
+{
+	int err;
+
+	err = do_unlink_wh(h_dir, h_path);
+	if (!err && dentry)
+		au_set_dbwh(dentry, -1);
+
+	return err;
+}
+
+static int unlink_wh_name(struct path *h_ppath, struct qstr *wh)
+{
+	int err;
+	struct path h_path;
+
+	err = 0;
+	h_path.dentry = vfsub_lkup_one(wh, h_ppath);
+	if (IS_ERR(h_path.dentry))
+		err = PTR_ERR(h_path.dentry);
+	else {
+		if (d_is_reg(h_path.dentry)) {
+			h_path.mnt = h_ppath->mnt;
+			err = do_unlink_wh(d_inode(h_ppath->dentry), &h_path);
+		}
+		dput(h_path.dentry);
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * initialize/clean whiteout for a branch
+ */
+
+static void au_wh_clean(struct inode *h_dir, struct path *whpath,
+			const int isdir)
+{
+	int err;
+	struct inode *delegated;
+
+	if (d_is_negative(whpath->dentry))
+		return;
+
+	if (isdir)
+		err = vfsub_rmdir(h_dir, whpath);
+	else {
+		delegated = NULL;
+		err = vfsub_unlink(h_dir, whpath, &delegated, /*force*/0);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal unlink\n");
+			iput(delegated);
+		}
+	}
+	if (unlikely(err))
+		pr_warn("failed removing %pd (%d), ignored.\n",
+			whpath->dentry, err);
+}
+
+static int test_linkable(struct dentry *h_root)
+{
+	struct inode *h_dir = d_inode(h_root);
+
+	if (h_dir->i_op->link)
+		return 0;
+
+	pr_err("%pd (%s) doesn't support link(2), use noplink and rw+nolwh\n",
+	       h_root, au_sbtype(h_root->d_sb));
+	return -ENOSYS;	/* the branch doesn't have its ->link() */
+}
+
+/* todo: should this mkdir be done in /sbin/mount.aufs helper? */
+static int au_whdir(struct inode *h_dir, struct path *path)
+{
+	int err;
+
+	err = -EEXIST;
+	if (d_is_negative(path->dentry)) {
+		int mode = 0700;
+
+		if (au_test_nfs(path->dentry->d_sb))
+			mode |= 0111;
+		err = vfsub_mkdir(h_dir, path, mode);
+	} else if (d_is_dir(path->dentry))
+		err = 0;
+	else
+		pr_err("unknown %pd exists\n", path->dentry);
+
+	return err;
+}
+
+struct au_wh_base {
+	const struct qstr *name;
+	struct dentry *dentry;
+};
+
+static void au_wh_init_ro(struct inode *h_dir, struct au_wh_base base[],
+			  struct path *h_path)
+{
+	h_path->dentry = base[AuBrWh_BASE].dentry;
+	au_wh_clean(h_dir, h_path, /*isdir*/0);
+	h_path->dentry = base[AuBrWh_PLINK].dentry;
+	au_wh_clean(h_dir, h_path, /*isdir*/1);
+	h_path->dentry = base[AuBrWh_ORPH].dentry;
+	au_wh_clean(h_dir, h_path, /*isdir*/1);
+}
+
+/*
+ * returns tri-state,
+ * minus: error, caller should print the message
+ * zero: success
+ * plus: error, caller should NOT print the message
+ */
+static int au_wh_init_rw_nolink(struct dentry *h_root, struct au_wbr *wbr,
+				int do_plink, struct au_wh_base base[],
+				struct path *h_path)
+{
+	int err;
+	struct inode *h_dir;
+
+	h_dir = d_inode(h_root);
+	h_path->dentry = base[AuBrWh_BASE].dentry;
+	au_wh_clean(h_dir, h_path, /*isdir*/0);
+	h_path->dentry = base[AuBrWh_PLINK].dentry;
+	if (do_plink) {
+		err = test_linkable(h_root);
+		if (unlikely(err)) {
+			err = 1;
+			goto out;
+		}
+
+		err = au_whdir(h_dir, h_path);
+		if (unlikely(err))
+			goto out;
+		wbr->wbr_plink = dget(base[AuBrWh_PLINK].dentry);
+	} else
+		au_wh_clean(h_dir, h_path, /*isdir*/1);
+	h_path->dentry = base[AuBrWh_ORPH].dentry;
+	err = au_whdir(h_dir, h_path);
+	if (unlikely(err))
+		goto out;
+	wbr->wbr_orph = dget(base[AuBrWh_ORPH].dentry);
+
+out:
+	return err;
+}
+
+/*
+ * for the moment, aufs supports the branch filesystem which does not support
+ * link(2). testing on FAT which does not support i_op->setattr() fully either,
+ * copyup failed. finally, such filesystem will not be used as the writable
+ * branch.
+ *
+ * returns tri-state, see above.
+ */
+static int au_wh_init_rw(struct dentry *h_root, struct au_wbr *wbr,
+			 int do_plink, struct au_wh_base base[],
+			 struct path *h_path)
+{
+	int err;
+	struct inode *h_dir;
+
+	WbrWhMustWriteLock(wbr);
+
+	err = test_linkable(h_root);
+	if (unlikely(err)) {
+		err = 1;
+		goto out;
+	}
+
+	/*
+	 * todo: should this create be done in /sbin/mount.aufs helper?
+	 */
+	err = -EEXIST;
+	h_dir = d_inode(h_root);
+	if (d_is_negative(base[AuBrWh_BASE].dentry)) {
+		h_path->dentry = base[AuBrWh_BASE].dentry;
+		err = vfsub_create(h_dir, h_path, WH_MASK, /*want_excl*/true);
+	} else if (d_is_reg(base[AuBrWh_BASE].dentry))
+		err = 0;
+	else
+		pr_err("unknown %pd2 exists\n", base[AuBrWh_BASE].dentry);
+	if (unlikely(err))
+		goto out;
+
+	h_path->dentry = base[AuBrWh_PLINK].dentry;
+	if (do_plink) {
+		err = au_whdir(h_dir, h_path);
+		if (unlikely(err))
+			goto out;
+		wbr->wbr_plink = dget(base[AuBrWh_PLINK].dentry);
+	} else
+		au_wh_clean(h_dir, h_path, /*isdir*/1);
+	wbr->wbr_whbase = dget(base[AuBrWh_BASE].dentry);
+
+	h_path->dentry = base[AuBrWh_ORPH].dentry;
+	err = au_whdir(h_dir, h_path);
+	if (unlikely(err))
+		goto out;
+	wbr->wbr_orph = dget(base[AuBrWh_ORPH].dentry);
+
+out:
+	return err;
+}
+
+/*
+ * initialize the whiteout base file/dir for @br.
+ */
+int au_wh_init(struct au_branch *br, struct super_block *sb)
+{
+	int err, i;
+	const unsigned char do_plink
+		= !!au_opt_test(au_mntflags(sb), PLINK);
+	struct inode *h_dir;
+	struct path path = br->br_path;
+	struct dentry *h_root = path.dentry;
+	struct au_wbr *wbr = br->br_wbr;
+	static const struct qstr base_name[] = {
+		[AuBrWh_BASE] = QSTR_INIT(AUFS_BASE_NAME,
+					  sizeof(AUFS_BASE_NAME) - 1),
+		[AuBrWh_PLINK] = QSTR_INIT(AUFS_PLINKDIR_NAME,
+					   sizeof(AUFS_PLINKDIR_NAME) - 1),
+		[AuBrWh_ORPH] = QSTR_INIT(AUFS_ORPHDIR_NAME,
+					  sizeof(AUFS_ORPHDIR_NAME) - 1)
+	};
+	struct au_wh_base base[] = {
+		[AuBrWh_BASE] = {
+			.name	= base_name + AuBrWh_BASE,
+			.dentry	= NULL
+		},
+		[AuBrWh_PLINK] = {
+			.name	= base_name + AuBrWh_PLINK,
+			.dentry	= NULL
+		},
+		[AuBrWh_ORPH] = {
+			.name	= base_name + AuBrWh_ORPH,
+			.dentry	= NULL
+		}
+	};
+
+	if (wbr)
+		WbrWhMustWriteLock(wbr);
+
+	for (i = 0; i < AuBrWh_Last; i++) {
+		/* doubly whiteouted */
+		struct dentry *d;
+
+		d = au_wh_lkup(h_root, (void *)base[i].name, br);
+		err = PTR_ERR(d);
+		if (IS_ERR(d))
+			goto out;
+
+		base[i].dentry = d;
+		AuDebugOn(wbr
+			  && wbr->wbr_wh[i]
+			  && wbr->wbr_wh[i] != base[i].dentry);
+	}
+
+	if (wbr)
+		for (i = 0; i < AuBrWh_Last; i++) {
+			dput(wbr->wbr_wh[i]);
+			wbr->wbr_wh[i] = NULL;
+		}
+
+	err = 0;
+	if (!au_br_writable(br->br_perm)) {
+		h_dir = d_inode(h_root);
+		au_wh_init_ro(h_dir, base, &path);
+	} else if (!au_br_wh_linkable(br->br_perm)) {
+		err = au_wh_init_rw_nolink(h_root, wbr, do_plink, base, &path);
+		if (err > 0)
+			goto out;
+		else if (err)
+			goto out_err;
+	} else {
+		err = au_wh_init_rw(h_root, wbr, do_plink, base, &path);
+		if (err > 0)
+			goto out;
+		else if (err)
+			goto out_err;
+	}
+	goto out; /* success */
+
+out_err:
+	pr_err("an error(%d) on the writable branch %pd(%s)\n",
+	       err, h_root, au_sbtype(h_root->d_sb));
+out:
+	for (i = 0; i < AuBrWh_Last; i++)
+		dput(base[i].dentry);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+/*
+ * whiteouts are all hard-linked usually.
+ * when its link count reaches a ceiling, we create a new whiteout base
+ * asynchronously.
+ */
+
+struct reinit_br_wh {
+	struct super_block *sb;
+	struct au_branch *br;
+};
+
+static void reinit_br_wh(void *arg)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct path h_path;
+	struct reinit_br_wh *a = arg;
+	struct au_wbr *wbr;
+	struct inode *dir, *delegated;
+	struct dentry *h_root;
+	struct au_hinode *hdir;
+
+	err = 0;
+	wbr = a->br->br_wbr;
+	/* big aufs lock */
+	si_noflush_write_lock(a->sb);
+	if (!au_br_writable(a->br->br_perm))
+		goto out;
+	bindex = au_br_index(a->sb, a->br->br_id);
+	if (unlikely(bindex < 0))
+		goto out;
+
+	di_read_lock_parent(a->sb->s_root, AuLock_IR);
+	dir = d_inode(a->sb->s_root);
+	hdir = au_hi(dir, bindex);
+	h_root = au_h_dptr(a->sb->s_root, bindex);
+	AuDebugOn(h_root != au_br_dentry(a->br));
+
+	au_hn_inode_lock_nested(hdir, AuLsc_I_PARENT);
+	wbr_wh_write_lock(wbr);
+	err = au_h_verify(wbr->wbr_whbase, au_opt_udba(a->sb), hdir->hi_inode,
+			  h_root, a->br);
+	if (!err) {
+		h_path.dentry = wbr->wbr_whbase;
+		h_path.mnt = au_br_mnt(a->br);
+		delegated = NULL;
+		err = vfsub_unlink(hdir->hi_inode, &h_path, &delegated,
+				   /*force*/0);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal unlink\n");
+			iput(delegated);
+		}
+	} else {
+		pr_warn("%pd is moved, ignored\n", wbr->wbr_whbase);
+		err = 0;
+	}
+	dput(wbr->wbr_whbase);
+	wbr->wbr_whbase = NULL;
+	if (!err)
+		err = au_wh_init(a->br, a->sb);
+	wbr_wh_write_unlock(wbr);
+	au_hn_inode_unlock(hdir);
+	di_read_unlock(a->sb->s_root, AuLock_IR);
+	if (!err)
+		au_fhsm_wrote(a->sb, bindex, /*force*/0);
+
+out:
+	if (wbr)
+		atomic_dec(&wbr->wbr_wh_running);
+	au_lcnt_dec(&a->br->br_count);
+	si_write_unlock(a->sb);
+	au_nwt_done(&au_sbi(a->sb)->si_nowait);
+	au_kfree_rcu(a);
+	if (unlikely(err))
+		AuIOErr("err %d\n", err);
+}
+
+static void kick_reinit_br_wh(struct super_block *sb, struct au_branch *br)
+{
+	int do_dec, wkq_err;
+	struct reinit_br_wh *arg;
+
+	do_dec = 1;
+	if (atomic_inc_return(&br->br_wbr->wbr_wh_running) != 1)
+		goto out;
+
+	/* ignore ENOMEM */
+	arg = kmalloc(sizeof(*arg), GFP_NOFS);
+	if (arg) {
+		/*
+		 * dec(wh_running), kfree(arg) and dec(br_count)
+		 * in reinit function
+		 */
+		arg->sb = sb;
+		arg->br = br;
+		au_lcnt_inc(&br->br_count);
+		wkq_err = au_wkq_nowait(reinit_br_wh, arg, sb, /*flags*/0);
+		if (unlikely(wkq_err)) {
+			atomic_dec(&br->br_wbr->wbr_wh_running);
+			au_lcnt_dec(&br->br_count);
+			au_kfree_rcu(arg);
+		}
+		do_dec = 0;
+	}
+
+out:
+	if (do_dec)
+		atomic_dec(&br->br_wbr->wbr_wh_running);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * create the whiteout @wh.
+ */
+static int link_or_create_wh(struct super_block *sb, aufs_bindex_t bindex,
+			     struct dentry *wh)
+{
+	int err;
+	struct path h_path = {
+		.dentry = wh
+	};
+	struct au_branch *br;
+	struct au_wbr *wbr;
+	struct dentry *h_parent;
+	struct inode *h_dir, *delegated;
+
+	h_parent = wh->d_parent; /* dir inode is locked */
+	h_dir = d_inode(h_parent);
+	IMustLock(h_dir);
+
+	br = au_sbr(sb, bindex);
+	h_path.mnt = au_br_mnt(br);
+	wbr = br->br_wbr;
+	wbr_wh_read_lock(wbr);
+	if (wbr->wbr_whbase) {
+		delegated = NULL;
+		err = vfsub_link(wbr->wbr_whbase, h_dir, &h_path, &delegated);
+		if (unlikely(err == -EWOULDBLOCK)) {
+			pr_warn("cannot retry for NFSv4 delegation"
+				" for an internal link\n");
+			iput(delegated);
+		}
+		if (!err || err != -EMLINK)
+			goto out;
+
+		/* link count full. re-initialize br_whbase. */
+		kick_reinit_br_wh(sb, br);
+	}
+
+	/* return this error in this context */
+	err = vfsub_create(h_dir, &h_path, WH_MASK, /*want_excl*/true);
+	if (!err)
+		au_fhsm_wrote(sb, bindex, /*force*/0);
+
+out:
+	wbr_wh_read_unlock(wbr);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * create or remove the diropq.
+ */
+static struct dentry *do_diropq(struct dentry *dentry, aufs_bindex_t bindex,
+				unsigned int flags)
+{
+	struct dentry *opq_dentry;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct path h_path;
+	int err;
+
+	sb = dentry->d_sb;
+	br = au_sbr(sb, bindex);
+	h_path.dentry = au_h_dptr(dentry, bindex);
+	h_path.mnt = au_br_mnt(br);
+	opq_dentry = vfsub_lkup_one(&diropq_name, &h_path);
+	if (IS_ERR(opq_dentry))
+		goto out;
+
+	if (au_ftest_diropq(flags, CREATE)) {
+		err = link_or_create_wh(sb, bindex, opq_dentry);
+		if (!err) {
+			au_set_dbdiropq(dentry, bindex);
+			goto out; /* success */
+		}
+	} else {
+		h_path.dentry = opq_dentry;
+		err = do_unlink_wh(au_h_iptr(d_inode(dentry), bindex), &h_path);
+		if (!err)
+			au_set_dbdiropq(dentry, -1);
+	}
+	dput(opq_dentry);
+	opq_dentry = ERR_PTR(err);
+
+out:
+	return opq_dentry;
+}
+
+struct do_diropq_args {
+	struct dentry **errp;
+	struct dentry *dentry;
+	aufs_bindex_t bindex;
+	unsigned int flags;
+};
+
+static void call_do_diropq(void *args)
+{
+	struct do_diropq_args *a = args;
+	*a->errp = do_diropq(a->dentry, a->bindex, a->flags);
+}
+
+struct dentry *au_diropq_sio(struct dentry *dentry, aufs_bindex_t bindex,
+			     unsigned int flags)
+{
+	struct dentry *diropq, *h_dentry;
+	struct user_namespace *h_userns;
+
+	h_userns = au_sbr_userns(dentry->d_sb, bindex);
+	h_dentry = au_h_dptr(dentry, bindex);
+	if (!au_test_h_perm_sio(h_userns, d_inode(h_dentry),
+				MAY_EXEC | MAY_WRITE))
+		diropq = do_diropq(dentry, bindex, flags);
+	else {
+		int wkq_err;
+		struct do_diropq_args args = {
+			.errp		= &diropq,
+			.dentry		= dentry,
+			.bindex		= bindex,
+			.flags		= flags
+		};
+
+		wkq_err = au_wkq_wait(call_do_diropq, &args);
+		if (unlikely(wkq_err))
+			diropq = ERR_PTR(wkq_err);
+	}
+
+	return diropq;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * lookup whiteout dentry.
+ * @h_parent: lower parent dentry which must exist and be locked
+ * @base_name: name of dentry which will be whiteouted
+ * returns dentry for whiteout.
+ */
+struct dentry *au_wh_lkup(struct dentry *h_parent, struct qstr *base_name,
+			  struct au_branch *br)
+{
+	int err;
+	struct qstr wh_name;
+	struct dentry *wh_dentry;
+	struct path h_path;
+
+	err = au_wh_name_alloc(&wh_name, base_name);
+	wh_dentry = ERR_PTR(err);
+	if (!err) {
+		h_path.dentry = h_parent;
+		h_path.mnt = au_br_mnt(br);
+		wh_dentry = vfsub_lkup_one(&wh_name, &h_path);
+		au_kfree_try_rcu(wh_name.name);
+	}
+	return wh_dentry;
+}
+
+/*
+ * link/create a whiteout for @dentry on @bindex.
+ */
+struct dentry *au_wh_create(struct dentry *dentry, aufs_bindex_t bindex,
+			    struct dentry *h_parent)
+{
+	struct dentry *wh_dentry;
+	struct super_block *sb;
+	int err;
+
+	sb = dentry->d_sb;
+	wh_dentry = au_wh_lkup(h_parent, &dentry->d_name, au_sbr(sb, bindex));
+	if (!IS_ERR(wh_dentry) && d_is_negative(wh_dentry)) {
+		err = link_or_create_wh(sb, bindex, wh_dentry);
+		if (!err) {
+			au_set_dbwh(dentry, bindex);
+			au_fhsm_wrote(sb, bindex, /*force*/0);
+		} else {
+			dput(wh_dentry);
+			wh_dentry = ERR_PTR(err);
+		}
+	}
+
+	return wh_dentry;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* Delete all whiteouts in this directory on branch bindex. */
+static int del_wh_children(struct path *h_path, struct au_nhash *whlist,
+			   aufs_bindex_t bindex)
+{
+	int err;
+	unsigned long ul, n;
+	struct qstr wh_name;
+	char *p;
+	struct hlist_head *head;
+	struct au_vdir_wh *pos;
+	struct au_vdir_destr *str;
+
+	err = -ENOMEM;
+	p = (void *)__get_free_page(GFP_NOFS);
+	wh_name.name = p;
+	if (unlikely(!wh_name.name))
+		goto out;
+
+	err = 0;
+	memcpy(p, AUFS_WH_PFX, AUFS_WH_PFX_LEN);
+	p += AUFS_WH_PFX_LEN;
+	n = whlist->nh_num;
+	head = whlist->nh_head;
+	for (ul = 0; !err && ul < n; ul++, head++) {
+		hlist_for_each_entry(pos, head, wh_hash) {
+			if (pos->wh_bindex != bindex)
+				continue;
+
+			str = &pos->wh_str;
+			if (str->len + AUFS_WH_PFX_LEN <= PATH_MAX) {
+				memcpy(p, str->name, str->len);
+				wh_name.len = AUFS_WH_PFX_LEN + str->len;
+				err = unlink_wh_name(h_path, &wh_name);
+				if (!err)
+					continue;
+				break;
+			}
+			AuIOErr("whiteout name too long %.*s\n",
+				str->len, str->name);
+			err = -EIO;
+			break;
+		}
+	}
+	free_page((unsigned long)wh_name.name);
+
+out:
+	return err;
+}
+
+struct del_wh_children_args {
+	int *errp;
+	struct path *h_path;
+	struct au_nhash *whlist;
+	aufs_bindex_t bindex;
+};
+
+static void call_del_wh_children(void *args)
+{
+	struct del_wh_children_args *a = args;
+	*a->errp = del_wh_children(a->h_path, a->whlist, a->bindex);
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_whtmp_rmdir *au_whtmp_rmdir_alloc(struct super_block *sb, gfp_t gfp)
+{
+	struct au_whtmp_rmdir *whtmp;
+	int err;
+	unsigned int rdhash;
+
+	SiMustAnyLock(sb);
+
+	whtmp = kzalloc(sizeof(*whtmp), gfp);
+	if (unlikely(!whtmp)) {
+		whtmp = ERR_PTR(-ENOMEM);
+		goto out;
+	}
+
+	/* no estimation for dir size */
+	rdhash = au_sbi(sb)->si_rdhash;
+	if (!rdhash)
+		rdhash = AUFS_RDHASH_DEF;
+	err = au_nhash_alloc(&whtmp->whlist, rdhash, gfp);
+	if (unlikely(err)) {
+		au_kfree_rcu(whtmp);
+		whtmp = ERR_PTR(err);
+	}
+
+out:
+	return whtmp;
+}
+
+void au_whtmp_rmdir_free(struct au_whtmp_rmdir *whtmp)
+{
+	if (whtmp->br)
+		au_lcnt_dec(&whtmp->br->br_count);
+	dput(whtmp->wh_dentry);
+	iput(whtmp->dir);
+	au_nhash_wh_free(&whtmp->whlist);
+	au_kfree_rcu(whtmp);
+}
+
+/*
+ * rmdir the whiteouted temporary named dir @h_dentry.
+ * @whlist: whiteouted children.
+ */
+int au_whtmp_rmdir(struct inode *dir, aufs_bindex_t bindex,
+		   struct dentry *wh_dentry, struct au_nhash *whlist)
+{
+	int err;
+	unsigned int h_nlink;
+	struct path wh_path;
+	struct inode *wh_inode, *h_dir;
+	struct au_branch *br;
+	struct user_namespace *h_userns;
+
+	h_dir = d_inode(wh_dentry->d_parent); /* dir inode is locked */
+	IMustLock(h_dir);
+
+	br = au_sbr(dir->i_sb, bindex);
+	wh_path.dentry = wh_dentry;
+	wh_path.mnt = au_br_mnt(br);
+	h_userns = au_br_userns(br);
+	wh_inode = d_inode(wh_dentry);
+	inode_lock_nested(wh_inode, AuLsc_I_CHILD);
+
+	/*
+	 * someone else might change some whiteouts while we were sleeping.
+	 * it means this whlist may have an obsoleted entry.
+	 */
+	if (!au_test_h_perm_sio(h_userns, wh_inode, MAY_EXEC | MAY_WRITE))
+		err = del_wh_children(&wh_path, whlist, bindex);
+	else {
+		int wkq_err;
+		struct del_wh_children_args args = {
+			.errp		= &err,
+			.h_path		= &wh_path,
+			.whlist		= whlist,
+			.bindex		= bindex
+		};
+
+		wkq_err = au_wkq_wait(call_del_wh_children, &args);
+		if (unlikely(wkq_err))
+			err = wkq_err;
+	}
+	inode_unlock(wh_inode);
+
+	if (!err) {
+		h_nlink = h_dir->i_nlink;
+		err = vfsub_rmdir(h_dir, &wh_path);
+		/* some fs doesn't change the parent nlink in some cases */
+		h_nlink -= h_dir->i_nlink;
+	}
+
+	if (!err) {
+		if (au_ibtop(dir) == bindex) {
+			/* todo: dir->i_mutex is necessary */
+			au_cpup_attr_timesizes(dir);
+			if (h_nlink)
+				vfsub_drop_nlink(dir);
+		}
+		return 0; /* success */
+	}
+
+	pr_warn("failed removing %pd(%d), ignored\n", wh_dentry, err);
+	return err;
+}
+
+static void call_rmdir_whtmp(void *args)
+{
+	int err;
+	aufs_bindex_t bindex;
+	struct au_whtmp_rmdir *a = args;
+	struct super_block *sb;
+	struct dentry *h_parent;
+	struct inode *h_dir;
+	struct au_hinode *hdir;
+
+	/* rmdir by nfsd may cause deadlock with this i_mutex */
+	/* inode_lock(a->dir); */
+	err = -EROFS;
+	sb = a->dir->i_sb;
+	si_read_lock(sb, !AuLock_FLUSH);
+	if (!au_br_writable(a->br->br_perm))
+		goto out;
+	bindex = au_br_index(sb, a->br->br_id);
+	if (unlikely(bindex < 0))
+		goto out;
+
+	err = -EIO;
+	ii_write_lock_parent(a->dir);
+	h_parent = dget_parent(a->wh_dentry);
+	h_dir = d_inode(h_parent);
+	hdir = au_hi(a->dir, bindex);
+	err = vfsub_mnt_want_write(au_br_mnt(a->br));
+	if (unlikely(err))
+		goto out_mnt;
+	au_hn_inode_lock_nested(hdir, AuLsc_I_PARENT);
+	err = au_h_verify(a->wh_dentry, au_opt_udba(sb), h_dir, h_parent,
+			  a->br);
+	if (!err)
+		err = au_whtmp_rmdir(a->dir, bindex, a->wh_dentry, &a->whlist);
+	au_hn_inode_unlock(hdir);
+	vfsub_mnt_drop_write(au_br_mnt(a->br));
+
+out_mnt:
+	dput(h_parent);
+	ii_write_unlock(a->dir);
+out:
+	/* inode_unlock(a->dir); */
+	au_whtmp_rmdir_free(a);
+	si_read_unlock(sb);
+	au_nwt_done(&au_sbi(sb)->si_nowait);
+	if (unlikely(err))
+		AuIOErr("err %d\n", err);
+}
+
+void au_whtmp_kick_rmdir(struct inode *dir, aufs_bindex_t bindex,
+			 struct dentry *wh_dentry, struct au_whtmp_rmdir *args)
+{
+	int wkq_err;
+	struct super_block *sb;
+
+	IMustLock(dir);
+
+	/* all post-process will be done in do_rmdir_whtmp(). */
+	sb = dir->i_sb;
+	args->dir = au_igrab(dir);
+	args->br = au_sbr(sb, bindex);
+	au_lcnt_inc(&args->br->br_count);
+	args->wh_dentry = dget(wh_dentry);
+	wkq_err = au_wkq_nowait(call_rmdir_whtmp, args, sb, /*flags*/0);
+	if (unlikely(wkq_err)) {
+		pr_warn("rmdir error %pd (%d), ignored\n", wh_dentry, wkq_err);
+		au_whtmp_rmdir_free(args);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/whout.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/whout.h
@@ -0,0 +1,87 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * whiteout for logical deletion and opaque directory
+ */
+
+#ifndef __AUFS_WHOUT_H__
+#define __AUFS_WHOUT_H__
+
+#ifdef __KERNEL__
+
+#include "dir.h"
+
+/* whout.c */
+int au_wh_name_alloc(struct qstr *wh, const struct qstr *name);
+int au_wh_test(struct user_namespace *h_userns, struct path *h_ppath,
+	       struct qstr *wh_name, int try_sio);
+int au_diropq_test(struct user_namespace *h_userns, struct path *h_path);
+struct au_branch;
+struct dentry *au_whtmp_lkup(struct dentry *h_parent, struct au_branch *br,
+			     struct qstr *prefix);
+int au_whtmp_ren(struct dentry *h_dentry, struct au_branch *br);
+int au_wh_unlink_dentry(struct inode *h_dir, struct path *h_path,
+			struct dentry *dentry);
+int au_wh_init(struct au_branch *br, struct super_block *sb);
+
+/* diropq flags */
+#define AuDiropq_CREATE	1
+#define au_ftest_diropq(flags, name)	((flags) & AuDiropq_##name)
+#define au_fset_diropq(flags, name) \
+	do { (flags) |= AuDiropq_##name; } while (0)
+#define au_fclr_diropq(flags, name) \
+	do { (flags) &= ~AuDiropq_##name; } while (0)
+
+struct dentry *au_diropq_sio(struct dentry *dentry, aufs_bindex_t bindex,
+			     unsigned int flags);
+struct dentry *au_wh_lkup(struct dentry *h_parent, struct qstr *base_name,
+			  struct au_branch *br);
+struct dentry *au_wh_create(struct dentry *dentry, aufs_bindex_t bindex,
+			    struct dentry *h_parent);
+
+/* real rmdir for the whiteout-ed dir */
+struct au_whtmp_rmdir {
+	struct inode *dir;
+	struct au_branch *br;
+	struct dentry *wh_dentry;
+	struct au_nhash whlist;
+};
+
+struct au_whtmp_rmdir *au_whtmp_rmdir_alloc(struct super_block *sb, gfp_t gfp);
+void au_whtmp_rmdir_free(struct au_whtmp_rmdir *whtmp);
+int au_whtmp_rmdir(struct inode *dir, aufs_bindex_t bindex,
+		   struct dentry *wh_dentry, struct au_nhash *whlist);
+void au_whtmp_kick_rmdir(struct inode *dir, aufs_bindex_t bindex,
+			 struct dentry *wh_dentry, struct au_whtmp_rmdir *args);
+
+/* ---------------------------------------------------------------------- */
+
+static inline struct dentry *au_diropq_create(struct dentry *dentry,
+					      aufs_bindex_t bindex)
+{
+	return au_diropq_sio(dentry, bindex, AuDiropq_CREATE);
+}
+
+static inline int au_diropq_remove(struct dentry *dentry, aufs_bindex_t bindex)
+{
+	return PTR_ERR(au_diropq_sio(dentry, bindex, !AuDiropq_CREATE));
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_WHOUT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/wkq.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/wkq.c
@@ -0,0 +1,372 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * workqueue for asynchronous/super-io operations
+ * todo: try new credential scheme
+ */
+
+#include <linux/module.h>
+#include "aufs.h"
+
+/* internal workqueue named AUFS_WKQ_NAME */
+
+static struct workqueue_struct *au_wkq;
+
+struct au_wkinfo {
+	struct work_struct wk;
+	struct kobject *kobj;
+
+	unsigned int flags; /* see wkq.h */
+
+	au_wkq_func_t func;
+	void *args;
+
+#ifdef CONFIG_LOCKDEP
+	int dont_check;
+	struct held_lock **hlock;
+#endif
+
+	struct completion *comp;
+};
+
+/* ---------------------------------------------------------------------- */
+/*
+ * Aufs passes some operations to the workqueue such as the internal copyup.
+ * This scheme looks rather unnatural for LOCKDEP debugging feature, since the
+ * job run by workqueue depends upon the locks acquired in the other task.
+ * Delegating a small operation to the workqueue, aufs passes its lockdep
+ * information too. And the job in the workqueue restores the info in order to
+ * pretend as if it acquired those locks. This is just to make LOCKDEP work
+ * correctly and expectedly.
+ */
+
+#ifndef CONFIG_LOCKDEP
+AuStubInt0(au_wkq_lockdep_alloc, struct au_wkinfo *wkinfo);
+AuStubVoid(au_wkq_lockdep_free, struct au_wkinfo *wkinfo);
+AuStubVoid(au_wkq_lockdep_pre, struct au_wkinfo *wkinfo);
+AuStubVoid(au_wkq_lockdep_post, struct au_wkinfo *wkinfo);
+AuStubVoid(au_wkq_lockdep_init, struct au_wkinfo *wkinfo);
+#else
+static void au_wkq_lockdep_init(struct au_wkinfo *wkinfo)
+{
+	wkinfo->hlock = NULL;
+	wkinfo->dont_check = 0;
+}
+
+/*
+ * 1: matched
+ * 0: unmatched
+ */
+static int au_wkq_lockdep_test(struct lock_class_key *key, const char *name)
+{
+	static DEFINE_SPINLOCK(spin);
+	static struct {
+		char *name;
+		struct lock_class_key *key;
+	} a[] = {
+		{ .name = "&sbinfo->si_rwsem" },
+		{ .name = "&finfo->fi_rwsem" },
+		{ .name = "&dinfo->di_rwsem" },
+		{ .name = "&iinfo->ii_rwsem" }
+	};
+	static int set;
+	int i;
+
+	/* lockless read from 'set.' see below */
+	if (set == ARRAY_SIZE(a)) {
+		for (i = 0; i < ARRAY_SIZE(a); i++)
+			if (a[i].key == key)
+				goto match;
+		goto unmatch;
+	}
+
+	spin_lock(&spin);
+	if (set)
+		for (i = 0; i < ARRAY_SIZE(a); i++)
+			if (a[i].key == key) {
+				spin_unlock(&spin);
+				goto match;
+			}
+	for (i = 0; i < ARRAY_SIZE(a); i++) {
+		if (a[i].key) {
+			if (unlikely(a[i].key == key)) { /* rare but possible */
+				spin_unlock(&spin);
+				goto match;
+			} else
+				continue;
+		}
+		if (strstr(a[i].name, name)) {
+			/*
+			 * the order of these three lines is important for the
+			 * lockless read above.
+			 */
+			a[i].key = key;
+			spin_unlock(&spin);
+			set++;
+			/* AuDbg("%d, %s\n", set, name); */
+			goto match;
+		}
+	}
+	spin_unlock(&spin);
+	goto unmatch;
+
+match:
+	return 1;
+unmatch:
+	return 0;
+}
+
+static int au_wkq_lockdep_alloc(struct au_wkinfo *wkinfo)
+{
+	int err, n;
+	struct task_struct *curr;
+	struct held_lock **hl, *held_locks, *p;
+
+	err = 0;
+	curr = current;
+	wkinfo->dont_check = lockdep_recursing(curr);
+	if (wkinfo->dont_check)
+		goto out;
+	n = curr->lockdep_depth;
+	if (!n)
+		goto out;
+
+	err = -ENOMEM;
+	wkinfo->hlock = kmalloc_array(n + 1, sizeof(*wkinfo->hlock), GFP_NOFS);
+	if (unlikely(!wkinfo->hlock))
+		goto out;
+
+	err = 0;
+#if 0 /* left for debugging */
+	if (0 && au_debug_test())
+		lockdep_print_held_locks(curr);
+#endif
+	held_locks = curr->held_locks;
+	hl = wkinfo->hlock;
+	while (n--) {
+		p = held_locks++;
+		if (au_wkq_lockdep_test(p->instance->key, p->instance->name))
+			*hl++ = p;
+	}
+	*hl = NULL;
+
+out:
+	return err;
+}
+
+static void au_wkq_lockdep_free(struct au_wkinfo *wkinfo)
+{
+	au_kfree_try_rcu(wkinfo->hlock);
+}
+
+static void au_wkq_lockdep_pre(struct au_wkinfo *wkinfo)
+{
+	struct held_lock *p, **hl = wkinfo->hlock;
+	int subclass;
+
+	if (wkinfo->dont_check)
+		lockdep_off();
+	if (!hl)
+		return;
+	while ((p = *hl++)) { /* assignment */
+		subclass = lockdep_hlock_class(p)->subclass;
+		/* AuDbg("%s, %d\n", p->instance->name, subclass); */
+		if (p->read)
+			rwsem_acquire_read(p->instance, subclass, 0,
+					   /*p->acquire_ip*/_RET_IP_);
+		else
+			rwsem_acquire(p->instance, subclass, 0,
+				      /*p->acquire_ip*/_RET_IP_);
+	}
+}
+
+static void au_wkq_lockdep_post(struct au_wkinfo *wkinfo)
+{
+	struct held_lock *p, **hl = wkinfo->hlock;
+
+	if (wkinfo->dont_check)
+		lockdep_on();
+	if (!hl)
+		return;
+	while ((p = *hl++)) /* assignment */
+		rwsem_release(p->instance, /*p->acquire_ip*/_RET_IP_);
+}
+#endif
+
+static void wkq_func(struct work_struct *wk)
+{
+	struct au_wkinfo *wkinfo = container_of(wk, struct au_wkinfo, wk);
+
+	AuDebugOn(!uid_eq(current_fsuid(), GLOBAL_ROOT_UID));
+	AuDebugOn(rlimit(RLIMIT_FSIZE) != RLIM_INFINITY);
+
+	au_wkq_lockdep_pre(wkinfo);
+	wkinfo->func(wkinfo->args);
+	au_wkq_lockdep_post(wkinfo);
+	if (au_ftest_wkq(wkinfo->flags, WAIT))
+		complete(wkinfo->comp);
+	else {
+		kobject_put(wkinfo->kobj);
+		module_put(THIS_MODULE); /* todo: ?? */
+		au_kfree_rcu(wkinfo);
+	}
+}
+
+/*
+ * Since struct completion is large, try allocating it dynamically.
+ */
+#define AuWkqCompDeclare(name)	struct completion *comp = NULL
+
+static int au_wkq_comp_alloc(struct au_wkinfo *wkinfo, struct completion **comp)
+{
+	*comp = kmalloc(sizeof(**comp), GFP_NOFS);
+	if (*comp) {
+		init_completion(*comp);
+		wkinfo->comp = *comp;
+		return 0;
+	}
+	return -ENOMEM;
+}
+
+static void au_wkq_comp_free(struct completion *comp)
+{
+	au_kfree_rcu(comp);
+}
+
+static void au_wkq_run(struct au_wkinfo *wkinfo)
+{
+	if (au_ftest_wkq(wkinfo->flags, NEST)) {
+		if (au_wkq_test()) {
+			AuWarn1("wkq from wkq, unless silly-rename on NFS,"
+				" due to a dead dir by UDBA,"
+				" or async xino write?\n");
+			AuDebugOn(au_ftest_wkq(wkinfo->flags, WAIT));
+		}
+	} else
+		au_dbg_verify_kthread();
+
+	if (au_ftest_wkq(wkinfo->flags, WAIT)) {
+		INIT_WORK_ONSTACK(&wkinfo->wk, wkq_func);
+		queue_work(au_wkq, &wkinfo->wk);
+	} else {
+		INIT_WORK(&wkinfo->wk, wkq_func);
+		schedule_work(&wkinfo->wk);
+	}
+}
+
+/*
+ * Be careful. It is easy to make deadlock happen.
+ * processA: lock, wkq and wait
+ * processB: wkq and wait, lock in wkq
+ * --> deadlock
+ */
+int au_wkq_do_wait(unsigned int flags, au_wkq_func_t func, void *args)
+{
+	int err;
+	AuWkqCompDeclare(comp);
+	struct au_wkinfo wkinfo = {
+		.flags	= flags,
+		.func	= func,
+		.args	= args
+	};
+
+	err = au_wkq_comp_alloc(&wkinfo, &comp);
+	if (unlikely(err))
+		goto out;
+	err = au_wkq_lockdep_alloc(&wkinfo);
+	if (unlikely(err))
+		goto out_comp;
+	if (!err) {
+		au_wkq_run(&wkinfo);
+		/* no timeout, no interrupt */
+		wait_for_completion(wkinfo.comp);
+	}
+	au_wkq_lockdep_free(&wkinfo);
+
+out_comp:
+	au_wkq_comp_free(comp);
+out:
+	destroy_work_on_stack(&wkinfo.wk);
+	return err;
+}
+
+/*
+ * Note: dget/dput() in func for aufs dentries are not supported. It will be a
+ * problem in a concurrent umounting.
+ */
+int au_wkq_nowait(au_wkq_func_t func, void *args, struct super_block *sb,
+		  unsigned int flags)
+{
+	int err;
+	struct au_wkinfo *wkinfo;
+
+	atomic_inc(&au_sbi(sb)->si_nowait.nw_len);
+
+	/*
+	 * wkq_func() must free this wkinfo.
+	 * it highly depends upon the implementation of workqueue.
+	 */
+	err = 0;
+	wkinfo = kmalloc(sizeof(*wkinfo), GFP_NOFS);
+	if (wkinfo) {
+		wkinfo->kobj = &au_sbi(sb)->si_kobj;
+		wkinfo->flags = flags & ~AuWkq_WAIT;
+		wkinfo->func = func;
+		wkinfo->args = args;
+		wkinfo->comp = NULL;
+		au_wkq_lockdep_init(wkinfo);
+		kobject_get(wkinfo->kobj);
+		__module_get(THIS_MODULE); /* todo: ?? */
+
+		au_wkq_run(wkinfo);
+	} else {
+		err = -ENOMEM;
+		au_nwt_done(&au_sbi(sb)->si_nowait);
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+void au_nwt_init(struct au_nowait_tasks *nwt)
+{
+	atomic_set(&nwt->nw_len, 0);
+	/* smp_mb(); */ /* atomic_set */
+	init_waitqueue_head(&nwt->nw_wq);
+}
+
+void au_wkq_fin(void)
+{
+	destroy_workqueue(au_wkq);
+}
+
+int __init au_wkq_init(void)
+{
+	int err;
+
+	err = 0;
+	au_wkq = alloc_workqueue(AUFS_WKQ_NAME, 0, WQ_DFL_ACTIVE);
+	if (IS_ERR(au_wkq))
+		err = PTR_ERR(au_wkq);
+	else if (!au_wkq)
+		err = -ENOMEM;
+
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/wkq.h
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/wkq.h
@@ -0,0 +1,89 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * workqueue for asynchronous/super-io operations
+ * todo: try new credentials management scheme
+ */
+
+#ifndef __AUFS_WKQ_H__
+#define __AUFS_WKQ_H__
+
+#ifdef __KERNEL__
+
+#include <linux/wait.h>
+
+struct super_block;
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * in the next operation, wait for the 'nowait' tasks in system-wide workqueue
+ */
+struct au_nowait_tasks {
+	atomic_t		nw_len;
+	wait_queue_head_t	nw_wq;
+};
+
+/* ---------------------------------------------------------------------- */
+
+typedef void (*au_wkq_func_t)(void *args);
+
+/* wkq flags */
+#define AuWkq_WAIT	1
+#define AuWkq_NEST	(1 << 1)
+#define au_ftest_wkq(flags, name)	((flags) & AuWkq_##name)
+#define au_fset_wkq(flags, name) \
+	do { (flags) |= AuWkq_##name; } while (0)
+#define au_fclr_wkq(flags, name) \
+	do { (flags) &= ~AuWkq_##name; } while (0)
+
+/* wkq.c */
+int au_wkq_do_wait(unsigned int flags, au_wkq_func_t func, void *args);
+int au_wkq_nowait(au_wkq_func_t func, void *args, struct super_block *sb,
+		  unsigned int flags);
+void au_nwt_init(struct au_nowait_tasks *nwt);
+int __init au_wkq_init(void);
+void au_wkq_fin(void);
+
+/* ---------------------------------------------------------------------- */
+
+static inline int au_wkq_test(void)
+{
+	return current->flags & PF_WQ_WORKER;
+}
+
+static inline int au_wkq_wait(au_wkq_func_t func, void *args)
+{
+	return au_wkq_do_wait(AuWkq_WAIT, func, args);
+}
+
+static inline void au_nwt_done(struct au_nowait_tasks *nwt)
+{
+	if (atomic_dec_and_test(&nwt->nw_len))
+		wake_up_all(&nwt->nw_wq);
+}
+
+static inline int au_nwt_flush(struct au_nowait_tasks *nwt)
+{
+	wait_event(nwt->nw_wq, !atomic_read(&nwt->nw_len));
+	return 0;
+}
+
+#endif /* __KERNEL__ */
+#endif /* __AUFS_WKQ_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/xattr.c
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2014-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * handling xattr functions
+ */
+
+#include <linux/fs.h>
+#include <linux/posix_acl_xattr.h>
+#include <linux/xattr.h>
+#include "aufs.h"
+
+static int au_xattr_ignore(int err, char *name, unsigned int ignore_flags)
+{
+	if (!ignore_flags)
+		goto out;
+	switch (err) {
+	case -ENOMEM:
+	case -EDQUOT:
+		goto out;
+	}
+
+	if ((ignore_flags & AuBrAttr_ICEX) == AuBrAttr_ICEX) {
+		err = 0;
+		goto out;
+	}
+
+#define cmp(brattr, prefix) do {					\
+		if (!strncmp(name, XATTR_##prefix##_PREFIX,		\
+			     XATTR_##prefix##_PREFIX_LEN)) {		\
+			if (ignore_flags & AuBrAttr_ICEX_##brattr)	\
+				err = 0;				\
+			goto out;					\
+		}							\
+	} while (0)
+
+	cmp(SEC, SECURITY);
+	cmp(SYS, SYSTEM);
+	cmp(TR, TRUSTED);
+	cmp(USR, USER);
+#undef cmp
+
+	if (ignore_flags & AuBrAttr_ICEX_OTH)
+		err = 0;
+
+out:
+	return err;
+}
+
+static const int au_xattr_out_of_list = AuBrAttr_ICEX_OTH << 1;
+
+static int au_do_cpup_xattr(struct path *h_dst, struct path *h_src,
+			    char *name, char **buf, unsigned int ignore_flags,
+			    unsigned int verbose)
+{
+	int err;
+	ssize_t ssz;
+	struct inode *h_idst;
+	struct dentry *h_dst_dentry, *h_src_dentry;
+	struct user_namespace *h_dst_userns, *h_src_userns;
+
+	h_src_userns = mnt_user_ns(h_src->mnt);
+	h_src_dentry = h_src->dentry;
+	ssz = vfs_getxattr_alloc(h_src_userns, h_src_dentry, name, buf, 0,
+				 GFP_NOFS);
+	err = ssz;
+	if (unlikely(err <= 0)) {
+		if (err == -ENODATA
+		    || (err == -EOPNOTSUPP
+			&& ((ignore_flags & au_xattr_out_of_list)
+			    || (au_test_nfs_noacl(d_inode(h_src_dentry))
+				&& (!strcmp(name, XATTR_NAME_POSIX_ACL_ACCESS)
+				    || !strcmp(name,
+					       XATTR_NAME_POSIX_ACL_DEFAULT))))
+			    ))
+			err = 0;
+		if (err && (verbose || au_debug_test()))
+			pr_err("%s, err %d\n", name, err);
+		goto out;
+	}
+
+	/* unlock it temporary */
+	h_dst_userns = mnt_user_ns(h_dst->mnt);
+	h_dst_dentry = h_dst->dentry;
+	h_idst = d_inode(h_dst_dentry);
+	inode_unlock(h_idst);
+	err = vfsub_setxattr(h_dst_userns, h_dst_dentry, name, *buf, ssz,
+			     /*flags*/0);
+	inode_lock_nested(h_idst, AuLsc_I_CHILD2);
+	if (unlikely(err)) {
+		if (verbose || au_debug_test())
+			pr_err("%s, err %d\n", name, err);
+		err = au_xattr_ignore(err, name, ignore_flags);
+	}
+
+out:
+	return err;
+}
+
+int au_cpup_xattr(struct path *h_dst, struct path *h_src, int ignore_flags,
+		  unsigned int verbose)
+{
+	int err, unlocked, acl_access, acl_default;
+	ssize_t ssz;
+	struct dentry *h_dst_dentry, *h_src_dentry;
+	struct inode *h_isrc, *h_idst;
+	char *value, *p, *o, *e;
+
+	/* try stopping to update the source inode while we are referencing */
+	/* there should not be the parent-child relationship between them */
+	h_dst_dentry = h_dst->dentry;
+	h_idst = d_inode(h_dst_dentry);
+	h_src_dentry = h_src->dentry;
+	h_isrc = d_inode(h_src_dentry);
+	inode_unlock(h_idst);
+	inode_lock_shared_nested(h_isrc, AuLsc_I_CHILD);
+	inode_lock_nested(h_idst, AuLsc_I_CHILD2);
+	unlocked = 0;
+
+	/* some filesystems don't list POSIX ACL, for example tmpfs */
+	ssz = vfs_listxattr(h_src_dentry, NULL, 0);
+	err = ssz;
+	if (unlikely(err < 0)) {
+		AuTraceErr(err);
+		if (err == -ENODATA
+		    || err == -EOPNOTSUPP)
+			err = 0;	/* ignore */
+		goto out;
+	}
+
+	err = 0;
+	p = NULL;
+	o = NULL;
+	if (ssz) {
+		err = -ENOMEM;
+		p = kmalloc(ssz, GFP_NOFS);
+		o = p;
+		if (unlikely(!p))
+			goto out;
+		err = vfs_listxattr(h_src_dentry, p, ssz);
+	}
+	inode_unlock_shared(h_isrc);
+	unlocked = 1;
+	AuDbg("err %d, ssz %zd\n", err, ssz);
+	if (unlikely(err < 0))
+		goto out_free;
+
+	err = 0;
+	e = p + ssz;
+	value = NULL;
+	acl_access = 0;
+	acl_default = 0;
+	while (!err && p < e) {
+		acl_access |= !strncmp(p, XATTR_NAME_POSIX_ACL_ACCESS,
+				       sizeof(XATTR_NAME_POSIX_ACL_ACCESS) - 1);
+		acl_default |= !strncmp(p, XATTR_NAME_POSIX_ACL_DEFAULT,
+					sizeof(XATTR_NAME_POSIX_ACL_DEFAULT)
+					- 1);
+		err = au_do_cpup_xattr(h_dst, h_src, p, &value, ignore_flags,
+				       verbose);
+		p += strlen(p) + 1;
+	}
+	AuTraceErr(err);
+	ignore_flags |= au_xattr_out_of_list;
+	if (!err && !acl_access) {
+		err = au_do_cpup_xattr(h_dst, h_src,
+				       XATTR_NAME_POSIX_ACL_ACCESS, &value,
+				       ignore_flags, verbose);
+		AuTraceErr(err);
+	}
+	if (!err && !acl_default) {
+		err = au_do_cpup_xattr(h_dst, h_src,
+				       XATTR_NAME_POSIX_ACL_DEFAULT, &value,
+				       ignore_flags, verbose);
+		AuTraceErr(err);
+	}
+
+	au_kfree_try_rcu(value);
+
+out_free:
+	au_kfree_try_rcu(o);
+out:
+	if (!unlocked)
+		inode_unlock_shared(h_isrc);
+	AuTraceErr(err);
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_smack_reentering(struct super_block *sb)
+{
+#if IS_ENABLED(CONFIG_SECURITY_SMACK) || IS_ENABLED(CONFIG_SECURITY_SELINUX)
+	/*
+	 * as a part of lookup, smack_d_instantiate() is called, and it calls
+	 * i_op->getxattr(). ouch.
+	 */
+	return si_pid_test(sb);
+#else
+	return 0;
+#endif
+}
+
+enum {
+	AU_XATTR_LIST,
+	AU_XATTR_GET
+};
+
+struct au_lgxattr {
+	int type;
+	union {
+		struct {
+			char	*list;
+			size_t	size;
+		} list;
+		struct {
+			const char	*name;
+			void		*value;
+			size_t		size;
+		} get;
+	} u;
+};
+
+static ssize_t au_lgxattr(struct dentry *dentry, struct inode *inode,
+			  struct au_lgxattr *arg)
+{
+	ssize_t err;
+	int reenter;
+	struct path h_path;
+	struct super_block *sb;
+
+	sb = dentry->d_sb;
+	reenter = au_smack_reentering(sb);
+	if (!reenter) {
+		err = si_read_lock(sb, AuLock_FLUSH | AuLock_NOPLM);
+		if (unlikely(err))
+			goto out;
+	}
+	err = au_h_path_getattr(dentry, inode, /*force*/1, &h_path, reenter);
+	if (unlikely(err))
+		goto out_si;
+	if (unlikely(!h_path.dentry))
+		/* illegally overlapped or something */
+		goto out_di; /* pretending success */
+
+	/* always topmost entry only */
+	switch (arg->type) {
+	case AU_XATTR_LIST:
+		err = vfs_listxattr(h_path.dentry,
+				    arg->u.list.list, arg->u.list.size);
+		break;
+	case AU_XATTR_GET:
+		AuDebugOn(d_is_negative(h_path.dentry));
+		err = vfs_getxattr(mnt_user_ns(h_path.mnt), h_path.dentry,
+				   arg->u.get.name, arg->u.get.value,
+				   arg->u.get.size);
+		break;
+	}
+
+out_di:
+	if (!reenter)
+		di_read_unlock(dentry, AuLock_IR);
+out_si:
+	if (!reenter)
+		si_read_unlock(sb);
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+ssize_t aufs_listxattr(struct dentry *dentry, char *list, size_t size)
+{
+	struct au_lgxattr arg = {
+		.type = AU_XATTR_LIST,
+		.u.list = {
+			.list	= list,
+			.size	= size
+		},
+	};
+
+	return au_lgxattr(dentry, /*inode*/NULL, &arg);
+}
+
+static ssize_t au_getxattr(struct dentry *dentry, struct inode *inode,
+			   const char *name, void *value, size_t size)
+{
+	struct au_lgxattr arg = {
+		.type = AU_XATTR_GET,
+		.u.get = {
+			.name	= name,
+			.value	= value,
+			.size	= size
+		},
+	};
+
+	return au_lgxattr(dentry, inode, &arg);
+}
+
+static int au_setxattr(struct dentry *dentry, struct inode *inode,
+		       const char *name, const void *value, size_t size,
+		       int flags)
+{
+	struct au_sxattr arg = {
+		.type = AU_XATTR_SET,
+		.u.set = {
+			.name	= name,
+			.value	= value,
+			.size	= size,
+			.flags	= flags
+		},
+	};
+
+	return au_sxattr(dentry, inode, &arg);
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_xattr_get(const struct xattr_handler *handler,
+			struct dentry *dentry, struct inode *inode,
+			const char *name, void *buffer, size_t size)
+{
+	return au_getxattr(dentry, inode, name, buffer, size);
+}
+
+static int au_xattr_set(const struct xattr_handler *handler,
+			struct user_namespace *userns,
+			struct dentry *dentry, struct inode *inode,
+			const char *name, const void *value, size_t size,
+			int flags)
+{
+	return au_setxattr(dentry, inode, name, value, size, flags);
+}
+
+static const struct xattr_handler au_xattr_handler = {
+	.name	= "",
+	.prefix	= "",
+	.get	= au_xattr_get,
+	.set	= au_xattr_set
+};
+
+static const struct xattr_handler *au_xattr_handlers[] = {
+#ifdef CONFIG_FS_POSIX_ACL
+	&posix_acl_access_xattr_handler,
+	&posix_acl_default_xattr_handler,
+#endif
+	&au_xattr_handler, /* must be last */
+	NULL
+};
+
+void au_xattr_init(struct super_block *sb)
+{
+	sb->s_xattr = au_xattr_handlers;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/aufs/xino.c
+++ linux-xilinx-zynqmp-5.15.0/fs/aufs/xino.c
@@ -0,0 +1,1926 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * external inode number translation table and bitmap
+ *
+ * things to consider
+ * - the lifetime
+ *   + au_xino object
+ *   + XINO files (xino, xib, xigen)
+ *   + dynamic debugfs entries (xiN)
+ *   + static debugfs entries (xib, xigen)
+ *   + static sysfs entry (xi_path)
+ * - several entry points to handle them.
+ *   + mount(2) without xino option (default)
+ *   + mount(2) with xino option
+ *   + mount(2) with noxino option
+ *   + umount(2)
+ *   + remount with add/del branches
+ *   + remount with xino/noxino options
+ */
+
+#include <linux/seq_file.h>
+#include <linux/statfs.h>
+#include "aufs.h"
+
+static aufs_bindex_t sbr_find_shared(struct super_block *sb, aufs_bindex_t btop,
+				     aufs_bindex_t bbot,
+				     struct super_block *h_sb)
+{
+	/* todo: try binary-search if the branches are many */
+	for (; btop <= bbot; btop++)
+		if (h_sb == au_sbr_sb(sb, btop))
+			return btop;
+	return -1;
+}
+
+/*
+ * find another branch who is on the same filesystem of the specified
+ * branch{@btgt}. search until @bbot.
+ */
+static aufs_bindex_t is_sb_shared(struct super_block *sb, aufs_bindex_t btgt,
+				  aufs_bindex_t bbot)
+{
+	aufs_bindex_t bindex;
+	struct super_block *tgt_sb;
+
+	tgt_sb = au_sbr_sb(sb, btgt);
+	bindex = sbr_find_shared(sb, /*btop*/0, btgt - 1, tgt_sb);
+	if (bindex < 0)
+		bindex = sbr_find_shared(sb, btgt + 1, bbot, tgt_sb);
+
+	return bindex;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * stop unnecessary notify events at creating xino files
+ */
+
+aufs_bindex_t au_xi_root(struct super_block *sb, struct dentry *dentry)
+{
+	aufs_bindex_t bfound, bindex, bbot;
+	struct dentry *parent;
+	struct au_branch *br;
+
+	bfound = -1;
+	parent = dentry->d_parent; /* safe d_parent access */
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (au_br_dentry(br) == parent) {
+			bfound = bindex;
+			break;
+		}
+	}
+
+	AuDbg("bfound b%d\n", bfound);
+	return bfound;
+}
+
+struct au_xino_lock_dir {
+	struct au_hinode *hdir;
+	struct dentry *parent;
+	struct inode *dir;
+};
+
+static struct dentry *au_dget_parent_lock(struct dentry *dentry,
+					  unsigned int lsc)
+{
+	struct dentry *parent;
+	struct inode *dir;
+
+	parent = dget_parent(dentry);
+	dir = d_inode(parent);
+	inode_lock_nested(dir, lsc);
+#if 0 /* it should not happen */
+	spin_lock(&dentry->d_lock);
+	if (unlikely(dentry->d_parent != parent)) {
+		spin_unlock(&dentry->d_lock);
+		inode_unlock(dir);
+		dput(parent);
+		parent = NULL;
+		goto out;
+	}
+	spin_unlock(&dentry->d_lock);
+
+out:
+#endif
+	return parent;
+}
+
+static void au_xino_lock_dir(struct super_block *sb, struct path *xipath,
+			     struct au_xino_lock_dir *ldir)
+{
+	aufs_bindex_t bindex;
+
+	ldir->hdir = NULL;
+	bindex = au_xi_root(sb, xipath->dentry);
+	if (bindex >= 0) {
+		/* rw branch root */
+		ldir->hdir = au_hi(d_inode(sb->s_root), bindex);
+		au_hn_inode_lock_nested(ldir->hdir, AuLsc_I_PARENT);
+	} else {
+		/* other */
+		ldir->parent = au_dget_parent_lock(xipath->dentry,
+						   AuLsc_I_PARENT);
+		ldir->dir = d_inode(ldir->parent);
+	}
+}
+
+static void au_xino_unlock_dir(struct au_xino_lock_dir *ldir)
+{
+	if (ldir->hdir)
+		au_hn_inode_unlock(ldir->hdir);
+	else {
+		inode_unlock(ldir->dir);
+		dput(ldir->parent);
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * create and set a new xino file
+ */
+struct file *au_xino_create(struct super_block *sb, char *fpath, int silent,
+			    int wbrtop)
+{
+	struct file *file;
+	struct dentry *h_parent, *d;
+	struct inode *h_dir, *inode;
+	int err;
+	static DEFINE_MUTEX(mtx);
+
+	/*
+	 * at mount-time, and the xino file is the default path,
+	 * hnotify is disabled so we have no notify events to ignore.
+	 * when a user specified the xino, we cannot get au_hdir to be ignored.
+	 */
+	if (!wbrtop)
+		mutex_lock(&mtx);
+	file = vfsub_filp_open(fpath, O_RDWR | O_CREAT | O_EXCL | O_LARGEFILE
+			       /* | __FMODE_NONOTIFY */,
+			       0666);
+	if (IS_ERR(file)) {
+		if (!wbrtop)
+			mutex_unlock(&mtx);
+		if (!silent)
+			pr_err("open %s(%ld)\n", fpath, PTR_ERR(file));
+		return file;
+	}
+
+	/* keep file count */
+	err = 0;
+	d = file->f_path.dentry;
+	h_parent = au_dget_parent_lock(d, AuLsc_I_PARENT);
+	if (!wbrtop)
+		mutex_unlock(&mtx);
+	/* mnt_want_write() is unnecessary here */
+	h_dir = d_inode(h_parent);
+	inode = file_inode(file);
+	/* no delegation since it is just created */
+	if (inode->i_nlink)
+		err = vfsub_unlink(h_dir, &file->f_path, /*delegated*/NULL,
+				   /*force*/0);
+	inode_unlock(h_dir);
+	dput(h_parent);
+	if (unlikely(err)) {
+		if (!silent)
+			pr_err("unlink %s(%d)\n", fpath, err);
+		goto out;
+	}
+
+	err = -EINVAL;
+	if (unlikely(sb == d->d_sb)) {
+		if (!silent)
+			pr_err("%s must be outside\n", fpath);
+		goto out;
+	}
+	if (unlikely(au_test_fs_bad_xino(d->d_sb))) {
+		if (!silent)
+			pr_err("xino doesn't support %s(%s)\n",
+			       fpath, au_sbtype(d->d_sb));
+		goto out;
+	}
+	return file; /* success */
+
+out:
+	fput(file);
+	file = ERR_PTR(err);
+	return file;
+}
+
+/*
+ * create a new xinofile at the same place/path as @base.
+ */
+struct file *au_xino_create2(struct super_block *sb, struct path *base,
+			     struct file *copy_src)
+{
+	struct file *file;
+	struct dentry *dentry;
+	struct inode *dir, *delegated;
+	struct qstr *name;
+	struct path ppath, path;
+	int err, do_unlock;
+	struct au_xino_lock_dir ldir;
+
+	do_unlock = 1;
+	au_xino_lock_dir(sb, base, &ldir);
+	dentry = base->dentry;
+	ppath.dentry = dentry->d_parent; /* dir inode is locked */
+	ppath.mnt = base->mnt;
+	dir = d_inode(ppath.dentry);
+	IMustLock(dir);
+
+	name = &dentry->d_name;
+	path.dentry = vfsub_lookup_one_len(name->name, &ppath, name->len);
+	if (IS_ERR(path.dentry)) {
+		file = (void *)path.dentry;
+		pr_err("%pd lookup err %ld\n", dentry, PTR_ERR(path.dentry));
+		goto out;
+	}
+
+	/* no need to mnt_want_write() since we call dentry_open() later */
+	err = vfs_create(mnt_user_ns(base->mnt), dir, path.dentry, 0666, NULL);
+	if (unlikely(err)) {
+		file = ERR_PTR(err);
+		pr_err("%pd create err %d\n", dentry, err);
+		goto out_dput;
+	}
+
+	path.mnt = base->mnt;
+	file = vfsub_dentry_open(&path,
+				 O_RDWR | O_CREAT | O_EXCL | O_LARGEFILE
+				 /* | __FMODE_NONOTIFY */);
+	if (IS_ERR(file)) {
+		pr_err("%pd open err %ld\n", dentry, PTR_ERR(file));
+		goto out_dput;
+	}
+
+	delegated = NULL;
+	err = vfsub_unlink(dir, &file->f_path, &delegated, /*force*/0);
+	au_xino_unlock_dir(&ldir);
+	do_unlock = 0;
+	if (unlikely(err == -EWOULDBLOCK)) {
+		pr_warn("cannot retry for NFSv4 delegation"
+			" for an internal unlink\n");
+		iput(delegated);
+	}
+	if (unlikely(err)) {
+		pr_err("%pd unlink err %d\n", dentry, err);
+		goto out_fput;
+	}
+
+	if (copy_src) {
+		/* no one can touch copy_src xino */
+		err = au_copy_file(file, copy_src, vfsub_f_size_read(copy_src));
+		if (unlikely(err)) {
+			pr_err("%pd copy err %d\n", dentry, err);
+			goto out_fput;
+		}
+	}
+	goto out_dput; /* success */
+
+out_fput:
+	fput(file);
+	file = ERR_PTR(err);
+out_dput:
+	dput(path.dentry);
+out:
+	if (do_unlock)
+		au_xino_unlock_dir(&ldir);
+	return file;
+}
+
+struct file *au_xino_file1(struct au_xino *xi)
+{
+	struct file *file;
+	unsigned int u, nfile;
+
+	file = NULL;
+	nfile = xi->xi_nfile;
+	for (u = 0; u < nfile; u++) {
+		file = xi->xi_file[u];
+		if (file)
+			break;
+	}
+
+	return file;
+}
+
+static int au_xino_file_set(struct au_xino *xi, int idx, struct file *file)
+{
+	int err;
+	struct file *f;
+	void *p;
+
+	if (file)
+		get_file(file);
+
+	err = 0;
+	f = NULL;
+	if (idx < xi->xi_nfile) {
+		f = xi->xi_file[idx];
+		if (f)
+			fput(f);
+	} else {
+		p = au_kzrealloc(xi->xi_file,
+				 sizeof(*xi->xi_file) * xi->xi_nfile,
+				 sizeof(*xi->xi_file) * (idx + 1),
+				 GFP_NOFS, /*may_shrink*/0);
+		if (p) {
+			MtxMustLock(&xi->xi_mtx);
+			xi->xi_file = p;
+			xi->xi_nfile = idx + 1;
+		} else {
+			err = -ENOMEM;
+			if (file)
+				fput(file);
+			goto out;
+		}
+	}
+	xi->xi_file[idx] = file;
+
+out:
+	return err;
+}
+
+/*
+ * if @xinew->xi is not set, then create new xigen file.
+ */
+struct file *au_xi_new(struct super_block *sb, struct au_xi_new *xinew)
+{
+	struct file *file;
+	int err;
+
+	SiMustAnyLock(sb);
+
+	file = au_xino_create2(sb, xinew->base, xinew->copy_src);
+	if (IS_ERR(file)) {
+		err = PTR_ERR(file);
+		pr_err("%s[%d], err %d\n",
+		       xinew->xi ? "xino" : "xigen",
+		       xinew->idx, err);
+		goto out;
+	}
+
+	if (xinew->xi)
+		err = au_xino_file_set(xinew->xi, xinew->idx, file);
+	else {
+		BUG();
+		/* todo: make xigen file an array */
+		/* err = au_xigen_file_set(sb, xinew->idx, file); */
+	}
+	fput(file);
+	if (unlikely(err))
+		file = ERR_PTR(err);
+
+out:
+	return file;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * truncate xino files
+ */
+static int au_xino_do_trunc(struct super_block *sb, aufs_bindex_t bindex,
+			    int idx, struct kstatfs *st)
+{
+	int err;
+	blkcnt_t blocks;
+	struct file *file, *new_xino;
+	struct au_xi_new xinew = {
+		.idx = idx
+	};
+
+	err = 0;
+	xinew.xi = au_sbr(sb, bindex)->br_xino;
+	file = au_xino_file(xinew.xi, idx);
+	if (!file)
+		goto out;
+
+	xinew.base = &file->f_path;
+	err = vfs_statfs(xinew.base, st);
+	if (unlikely(err)) {
+		AuErr1("statfs err %d, ignored\n", err);
+		err = 0;
+		goto out;
+	}
+
+	blocks = file_inode(file)->i_blocks;
+	pr_info("begin truncating xino(b%d-%d), ib%llu, %llu/%llu free blks\n",
+		bindex, idx, (u64)blocks, st->f_bfree, st->f_blocks);
+
+	xinew.copy_src = file;
+	new_xino = au_xi_new(sb, &xinew);
+	if (IS_ERR(new_xino)) {
+		err = PTR_ERR(new_xino);
+		pr_err("xino(b%d-%d), err %d, ignored\n", bindex, idx, err);
+		goto out;
+	}
+
+	err = vfs_statfs(&new_xino->f_path, st);
+	if (!err)
+		pr_info("end truncating xino(b%d-%d), ib%llu, %llu/%llu free blks\n",
+			bindex, idx, (u64)file_inode(new_xino)->i_blocks,
+			st->f_bfree, st->f_blocks);
+	else {
+		AuErr1("statfs err %d, ignored\n", err);
+		err = 0;
+	}
+
+out:
+	return err;
+}
+
+int au_xino_trunc(struct super_block *sb, aufs_bindex_t bindex, int idx_begin)
+{
+	int err, i;
+	unsigned long jiffy;
+	aufs_bindex_t bbot;
+	struct kstatfs *st;
+	struct au_branch *br;
+	struct au_xino *xi;
+
+	err = -ENOMEM;
+	st = kmalloc(sizeof(*st), GFP_NOFS);
+	if (unlikely(!st))
+		goto out;
+
+	err = -EINVAL;
+	bbot = au_sbbot(sb);
+	if (unlikely(bindex < 0 || bbot < bindex))
+		goto out_st;
+
+	err = 0;
+	jiffy = jiffies;
+	br = au_sbr(sb, bindex);
+	xi = br->br_xino;
+	for (i = idx_begin; !err && i < xi->xi_nfile; i++)
+		err = au_xino_do_trunc(sb, bindex, i, st);
+	if (!err)
+		au_sbi(sb)->si_xino_jiffy = jiffy;
+
+out_st:
+	au_kfree_rcu(st);
+out:
+	return err;
+}
+
+struct xino_do_trunc_args {
+	struct super_block *sb;
+	struct au_branch *br;
+	int idx;
+};
+
+static void xino_do_trunc(void *_args)
+{
+	struct xino_do_trunc_args *args = _args;
+	struct super_block *sb;
+	struct au_branch *br;
+	struct inode *dir;
+	int err, idx;
+	aufs_bindex_t bindex;
+
+	err = 0;
+	sb = args->sb;
+	dir = d_inode(sb->s_root);
+	br = args->br;
+	idx = args->idx;
+
+	si_noflush_write_lock(sb);
+	ii_read_lock_parent(dir);
+	bindex = au_br_index(sb, br->br_id);
+	err = au_xino_trunc(sb, bindex, idx);
+	ii_read_unlock(dir);
+	if (unlikely(err))
+		pr_warn("err b%d, (%d)\n", bindex, err);
+	atomic_dec(&br->br_xino->xi_truncating);
+	au_lcnt_dec(&br->br_count);
+	si_write_unlock(sb);
+	au_nwt_done(&au_sbi(sb)->si_nowait);
+	au_kfree_rcu(args);
+}
+
+/*
+ * returns the index in the xi_file array whose corresponding file is necessary
+ * to truncate, or -1 which means no need to truncate.
+ */
+static int xino_trunc_test(struct super_block *sb, struct au_branch *br)
+{
+	int err;
+	unsigned int u;
+	struct kstatfs st;
+	struct au_sbinfo *sbinfo;
+	struct au_xino *xi;
+	struct file *file;
+
+	/* todo: si_xino_expire and the ratio should be customizable */
+	sbinfo = au_sbi(sb);
+	if (time_before(jiffies,
+			sbinfo->si_xino_jiffy + sbinfo->si_xino_expire))
+		return -1;
+
+	/* truncation border */
+	xi = br->br_xino;
+	for (u = 0; u < xi->xi_nfile; u++) {
+		file = au_xino_file(xi, u);
+		if (!file)
+			continue;
+
+		err = vfs_statfs(&file->f_path, &st);
+		if (unlikely(err)) {
+			AuErr1("statfs err %d, ignored\n", err);
+			return -1;
+		}
+		if (div64_u64(st.f_bfree * 100, st.f_blocks)
+		    >= AUFS_XINO_DEF_TRUNC)
+			return u;
+	}
+
+	return -1;
+}
+
+static void xino_try_trunc(struct super_block *sb, struct au_branch *br)
+{
+	int idx;
+	struct xino_do_trunc_args *args;
+	int wkq_err;
+
+	idx = xino_trunc_test(sb, br);
+	if (idx < 0)
+		return;
+
+	if (atomic_inc_return(&br->br_xino->xi_truncating) > 1)
+		goto out;
+
+	/* lock and kfree() will be called in trunc_xino() */
+	args = kmalloc(sizeof(*args), GFP_NOFS);
+	if (unlikely(!args)) {
+		AuErr1("no memory\n");
+		goto out;
+	}
+
+	au_lcnt_inc(&br->br_count);
+	args->sb = sb;
+	args->br = br;
+	args->idx = idx;
+	wkq_err = au_wkq_nowait(xino_do_trunc, args, sb, /*flags*/0);
+	if (!wkq_err)
+		return; /* success */
+
+	pr_err("wkq %d\n", wkq_err);
+	au_lcnt_dec(&br->br_count);
+	au_kfree_rcu(args);
+
+out:
+	atomic_dec(&br->br_xino->xi_truncating);
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_xi_calc {
+	int idx;
+	loff_t pos;
+};
+
+static void au_xi_calc(struct super_block *sb, ino_t h_ino,
+		       struct au_xi_calc *calc)
+{
+	loff_t maxent;
+
+	maxent = au_xi_maxent(sb);
+	calc->idx = div64_u64_rem(h_ino, maxent, &calc->pos);
+	calc->pos *= sizeof(ino_t);
+}
+
+static int au_xino_do_new_async(struct super_block *sb, struct au_branch *br,
+				struct au_xi_calc *calc)
+{
+	int err;
+	struct file *file;
+	struct au_xino *xi = br->br_xino;
+	struct au_xi_new xinew = {
+		.xi = xi
+	};
+
+	SiMustAnyLock(sb);
+
+	err = 0;
+	if (!xi)
+		goto out;
+
+	mutex_lock(&xi->xi_mtx);
+	file = au_xino_file(xi, calc->idx);
+	if (file)
+		goto out_mtx;
+
+	file = au_xino_file(xi, /*idx*/-1);
+	AuDebugOn(!file);
+	xinew.idx = calc->idx;
+	xinew.base = &file->f_path;
+	/* xinew.copy_src = NULL; */
+	file = au_xi_new(sb, &xinew);
+	if (IS_ERR(file))
+		err = PTR_ERR(file);
+
+out_mtx:
+	mutex_unlock(&xi->xi_mtx);
+out:
+	return err;
+}
+
+struct au_xino_do_new_async_args {
+	struct super_block *sb;
+	struct au_branch *br;
+	struct au_xi_calc calc;
+	ino_t ino;
+};
+
+struct au_xi_writing {
+	struct hlist_bl_node node;
+	ino_t h_ino, ino;
+};
+
+static int au_xino_do_write(struct file *file, struct au_xi_calc *calc,
+			    ino_t ino);
+
+static void au_xino_call_do_new_async(void *args)
+{
+	struct au_xino_do_new_async_args *a = args;
+	struct au_branch *br;
+	struct super_block *sb;
+	struct au_sbinfo *sbi;
+	struct inode *root;
+	struct file *file;
+	struct au_xi_writing *del, *p;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	int err;
+
+	br = a->br;
+	sb = a->sb;
+	sbi = au_sbi(sb);
+	si_noflush_read_lock(sb);
+	root = d_inode(sb->s_root);
+	ii_read_lock_child(root);
+	err = au_xino_do_new_async(sb, br, &a->calc);
+	if (unlikely(err)) {
+		AuIOErr("err %d\n", err);
+		goto out;
+	}
+
+	file = au_xino_file(br->br_xino, a->calc.idx);
+	AuDebugOn(!file);
+	err = au_xino_do_write(file, &a->calc, a->ino);
+	if (unlikely(err)) {
+		AuIOErr("err %d\n", err);
+		goto out;
+	}
+
+	del = NULL;
+	hbl = &br->br_xino->xi_writing;
+	hlist_bl_lock(hbl);
+	au_hbl_for_each(pos, hbl) {
+		p = container_of(pos, struct au_xi_writing, node);
+		if (p->ino == a->ino) {
+			del = p;
+			hlist_bl_del(&p->node);
+			break;
+		}
+	}
+	hlist_bl_unlock(hbl);
+	au_kfree_rcu(del);
+
+out:
+	au_lcnt_dec(&br->br_count);
+	ii_read_unlock(root);
+	si_read_unlock(sb);
+	au_nwt_done(&sbi->si_nowait);
+	au_kfree_rcu(a);
+}
+
+/*
+ * create a new xino file asynchronously
+ */
+static int au_xino_new_async(struct super_block *sb, struct au_branch *br,
+			     struct au_xi_calc *calc, ino_t ino)
+{
+	int err;
+	struct au_xino_do_new_async_args *arg;
+
+	err = -ENOMEM;
+	arg = kmalloc(sizeof(*arg), GFP_NOFS);
+	if (unlikely(!arg))
+		goto out;
+
+	arg->sb = sb;
+	arg->br = br;
+	arg->calc = *calc;
+	arg->ino = ino;
+	au_lcnt_inc(&br->br_count);
+	err = au_wkq_nowait(au_xino_call_do_new_async, arg, sb, AuWkq_NEST);
+	if (unlikely(err)) {
+		pr_err("wkq %d\n", err);
+		au_lcnt_dec(&br->br_count);
+		au_kfree_rcu(arg);
+	}
+
+out:
+	return err;
+}
+
+/*
+ * read @ino from xinofile for the specified branch{@sb, @bindex}
+ * at the position of @h_ino.
+ */
+int au_xino_read(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+		 ino_t *ino)
+{
+	int err;
+	ssize_t sz;
+	struct au_xi_calc calc;
+	struct au_sbinfo *sbinfo;
+	struct file *file;
+	struct au_xino *xi;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos;
+	struct au_xi_writing *p;
+
+	*ino = 0;
+	if (!au_opt_test(au_mntflags(sb), XINO))
+		return 0; /* no xino */
+
+	err = 0;
+	au_xi_calc(sb, h_ino, &calc);
+	xi = au_sbr(sb, bindex)->br_xino;
+	file = au_xino_file(xi, calc.idx);
+	if (!file) {
+		hbl = &xi->xi_writing;
+		hlist_bl_lock(hbl);
+		au_hbl_for_each(pos, hbl) {
+			p = container_of(pos, struct au_xi_writing, node);
+			if (p->h_ino == h_ino) {
+				AuDbg("hi%llu, i%llu, found\n",
+				      (u64)p->h_ino, (u64)p->ino);
+				*ino = p->ino;
+				break;
+			}
+		}
+		hlist_bl_unlock(hbl);
+		return 0;
+	} else if (vfsub_f_size_read(file) < calc.pos + sizeof(*ino))
+		return 0; /* no xino */
+
+	sbinfo = au_sbi(sb);
+	sz = xino_fread(file, ino, sizeof(*ino), &calc.pos);
+	if (sz == sizeof(*ino))
+		return 0; /* success */
+
+	err = sz;
+	if (unlikely(sz >= 0)) {
+		err = -EIO;
+		AuIOErr("xino read error (%zd)\n", sz);
+	}
+	return err;
+}
+
+static int au_xino_do_write(struct file *file, struct au_xi_calc *calc,
+			    ino_t ino)
+{
+	ssize_t sz;
+
+	sz = xino_fwrite(file, &ino, sizeof(ino), &calc->pos);
+	if (sz == sizeof(ino))
+		return 0; /* success */
+
+	AuIOErr("write failed (%zd)\n", sz);
+	return -EIO;
+}
+
+/*
+ * write @ino to the xinofile for the specified branch{@sb, @bindex}
+ * at the position of @h_ino.
+ * even if @ino is zero, it is written to the xinofile and means no entry.
+ * if the size of the xino file on a specific filesystem exceeds the watermark,
+ * try truncating it.
+ */
+int au_xino_write(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+		  ino_t ino)
+{
+	int err;
+	unsigned int mnt_flags;
+	struct au_xi_calc calc;
+	struct file *file;
+	struct au_branch *br;
+	struct au_xino *xi;
+	struct au_xi_writing *p;
+
+	SiMustAnyLock(sb);
+
+	mnt_flags = au_mntflags(sb);
+	if (!au_opt_test(mnt_flags, XINO))
+		return 0;
+
+	au_xi_calc(sb, h_ino, &calc);
+	br = au_sbr(sb, bindex);
+	xi = br->br_xino;
+	file = au_xino_file(xi, calc.idx);
+	if (!file) {
+		/* store the inum pair into the list */
+		p = kmalloc(sizeof(*p), GFP_NOFS | __GFP_NOFAIL);
+		p->h_ino = h_ino;
+		p->ino = ino;
+		au_hbl_add(&p->node, &xi->xi_writing);
+
+		/* create and write a new xino file asynchronously */
+		err = au_xino_new_async(sb, br, &calc, ino);
+		if (!err)
+			return 0; /* success */
+		goto out;
+	}
+
+	err = au_xino_do_write(file, &calc, ino);
+	if (!err) {
+		br = au_sbr(sb, bindex);
+		if (au_opt_test(mnt_flags, TRUNC_XINO)
+		    && au_test_fs_trunc_xino(au_br_sb(br)))
+			xino_try_trunc(sb, br);
+		return 0; /* success */
+	}
+
+out:
+	AuIOErr("write failed (%d)\n", err);
+	return -EIO;
+}
+
+static ssize_t xino_fread_wkq(struct file *file, void *buf, size_t size,
+			      loff_t *pos);
+
+/* todo: unnecessary to support mmap_sem since kernel-space? */
+ssize_t xino_fread(struct file *file, void *kbuf, size_t size, loff_t *pos)
+{
+	ssize_t err;
+	int i;
+	const int prevent_endless = 10;
+
+	i = 0;
+	do {
+		err = vfsub_read_k(file, kbuf, size, pos);
+		if (err == -EINTR
+		    && !au_wkq_test()
+		    && fatal_signal_pending(current)) {
+			err = xino_fread_wkq(file, kbuf, size, pos);
+			BUG_ON(err == -EINTR);
+		}
+	} while (i++ < prevent_endless
+		 && (err == -EAGAIN || err == -EINTR));
+
+#if 0 /* reserved for future use */
+	if (err > 0)
+		fsnotify_access(file->f_path.dentry);
+#endif
+
+	return err;
+}
+
+struct xino_fread_args {
+	ssize_t *errp;
+	struct file *file;
+	void *buf;
+	size_t size;
+	loff_t *pos;
+};
+
+static void call_xino_fread(void *args)
+{
+	struct xino_fread_args *a = args;
+	*a->errp = xino_fread(a->file, a->buf, a->size, a->pos);
+}
+
+static ssize_t xino_fread_wkq(struct file *file, void *buf, size_t size,
+			      loff_t *pos)
+{
+	ssize_t err;
+	int wkq_err;
+	struct xino_fread_args args = {
+		.errp	= &err,
+		.file	= file,
+		.buf	= buf,
+		.size	= size,
+		.pos	= pos
+	};
+
+	wkq_err = au_wkq_wait(call_xino_fread, &args);
+	if (unlikely(wkq_err))
+		err = wkq_err;
+
+	return err;
+}
+
+static ssize_t xino_fwrite_wkq(struct file *file, void *buf, size_t size,
+			       loff_t *pos);
+
+static ssize_t do_xino_fwrite(struct file *file, void *kbuf, size_t size,
+			      loff_t *pos)
+{
+	ssize_t err;
+	int i;
+	const int prevent_endless = 10;
+
+	i = 0;
+	do {
+		err = vfsub_write_k(file, kbuf, size, pos);
+		if (err == -EINTR
+		    && !au_wkq_test()
+		    && fatal_signal_pending(current)) {
+			err = xino_fwrite_wkq(file, kbuf, size, pos);
+			BUG_ON(err == -EINTR);
+		}
+	} while (i++ < prevent_endless
+		 && (err == -EAGAIN || err == -EINTR));
+
+#if 0 /* reserved for future use */
+	if (err > 0)
+		fsnotify_modify(file->f_path.dentry);
+#endif
+
+	return err;
+}
+
+struct do_xino_fwrite_args {
+	ssize_t *errp;
+	struct file *file;
+	void *buf;
+	size_t size;
+	loff_t *pos;
+};
+
+static void call_do_xino_fwrite(void *args)
+{
+	struct do_xino_fwrite_args *a = args;
+	*a->errp = do_xino_fwrite(a->file, a->buf, a->size, a->pos);
+}
+
+static ssize_t xino_fwrite_wkq(struct file *file, void *buf, size_t size,
+			       loff_t *pos)
+{
+	ssize_t err;
+	int wkq_err;
+	struct do_xino_fwrite_args args = {
+		.errp	= &err,
+		.file	= file,
+		.buf	= buf,
+		.size	= size,
+		.pos	= pos
+	};
+
+	/*
+	 * it breaks RLIMIT_FSIZE and normal user's limit,
+	 * users should care about quota and real 'filesystem full.'
+	 */
+	wkq_err = au_wkq_wait(call_do_xino_fwrite, &args);
+	if (unlikely(wkq_err))
+		err = wkq_err;
+
+	return err;
+}
+
+ssize_t xino_fwrite(struct file *file, void *buf, size_t size, loff_t *pos)
+{
+	ssize_t err;
+
+	if (rlimit(RLIMIT_FSIZE) == RLIM_INFINITY) {
+		lockdep_off();
+		err = do_xino_fwrite(file, buf, size, pos);
+		lockdep_on();
+	} else {
+		lockdep_off();
+		err = xino_fwrite_wkq(file, buf, size, pos);
+		lockdep_on();
+	}
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * inode number bitmap
+ */
+static const int page_bits = (int)PAGE_SIZE * BITS_PER_BYTE;
+static ino_t xib_calc_ino(unsigned long pindex, int bit)
+{
+	ino_t ino;
+
+	AuDebugOn(bit < 0 || page_bits <= bit);
+	ino = AUFS_FIRST_INO + pindex * page_bits + bit;
+	return ino;
+}
+
+static void xib_calc_bit(ino_t ino, unsigned long *pindex, int *bit)
+{
+	AuDebugOn(ino < AUFS_FIRST_INO);
+	ino -= AUFS_FIRST_INO;
+	*pindex = ino / page_bits;
+	*bit = ino % page_bits;
+}
+
+static int xib_pindex(struct super_block *sb, unsigned long pindex)
+{
+	int err;
+	loff_t pos;
+	ssize_t sz;
+	struct au_sbinfo *sbinfo;
+	struct file *xib;
+	unsigned long *p;
+
+	sbinfo = au_sbi(sb);
+	MtxMustLock(&sbinfo->si_xib_mtx);
+	AuDebugOn(pindex > ULONG_MAX / PAGE_SIZE
+		  || !au_opt_test(sbinfo->si_mntflags, XINO));
+
+	if (pindex == sbinfo->si_xib_last_pindex)
+		return 0;
+
+	xib = sbinfo->si_xib;
+	p = sbinfo->si_xib_buf;
+	pos = sbinfo->si_xib_last_pindex;
+	pos *= PAGE_SIZE;
+	sz = xino_fwrite(xib, p, PAGE_SIZE, &pos);
+	if (unlikely(sz != PAGE_SIZE))
+		goto out;
+
+	pos = pindex;
+	pos *= PAGE_SIZE;
+	if (vfsub_f_size_read(xib) >= pos + PAGE_SIZE)
+		sz = xino_fread(xib, p, PAGE_SIZE, &pos);
+	else {
+		memset(p, 0, PAGE_SIZE);
+		sz = xino_fwrite(xib, p, PAGE_SIZE, &pos);
+	}
+	if (sz == PAGE_SIZE) {
+		sbinfo->si_xib_last_pindex = pindex;
+		return 0; /* success */
+	}
+
+out:
+	AuIOErr1("write failed (%zd)\n", sz);
+	err = sz;
+	if (sz >= 0)
+		err = -EIO;
+	return err;
+}
+
+static void au_xib_clear_bit(struct inode *inode)
+{
+	int err, bit;
+	unsigned long pindex;
+	struct super_block *sb;
+	struct au_sbinfo *sbinfo;
+
+	AuDebugOn(inode->i_nlink);
+
+	sb = inode->i_sb;
+	xib_calc_bit(inode->i_ino, &pindex, &bit);
+	AuDebugOn(page_bits <= bit);
+	sbinfo = au_sbi(sb);
+	mutex_lock(&sbinfo->si_xib_mtx);
+	err = xib_pindex(sb, pindex);
+	if (!err) {
+		clear_bit(bit, sbinfo->si_xib_buf);
+		sbinfo->si_xib_next_bit = bit;
+	}
+	mutex_unlock(&sbinfo->si_xib_mtx);
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * truncate a xino bitmap file
+ */
+
+/* todo: slow */
+static int do_xib_restore(struct super_block *sb, struct file *file, void *page)
+{
+	int err, bit;
+	ssize_t sz;
+	unsigned long pindex;
+	loff_t pos, pend;
+	struct au_sbinfo *sbinfo;
+	ino_t *ino;
+	unsigned long *p;
+
+	err = 0;
+	sbinfo = au_sbi(sb);
+	MtxMustLock(&sbinfo->si_xib_mtx);
+	p = sbinfo->si_xib_buf;
+	pend = vfsub_f_size_read(file);
+	pos = 0;
+	while (pos < pend) {
+		sz = xino_fread(file, page, PAGE_SIZE, &pos);
+		err = sz;
+		if (unlikely(sz <= 0))
+			goto out;
+
+		err = 0;
+		for (ino = page; sz > 0; ino++, sz -= sizeof(ino)) {
+			if (unlikely(*ino < AUFS_FIRST_INO))
+				continue;
+
+			xib_calc_bit(*ino, &pindex, &bit);
+			AuDebugOn(page_bits <= bit);
+			err = xib_pindex(sb, pindex);
+			if (!err)
+				set_bit(bit, p);
+			else
+				goto out;
+		}
+	}
+
+out:
+	return err;
+}
+
+static int xib_restore(struct super_block *sb)
+{
+	int err, i;
+	unsigned int nfile;
+	aufs_bindex_t bindex, bbot;
+	void *page;
+	struct au_branch *br;
+	struct au_xino *xi;
+	struct file *file;
+
+	err = -ENOMEM;
+	page = (void *)__get_free_page(GFP_NOFS);
+	if (unlikely(!page))
+		goto out;
+
+	err = 0;
+	bbot = au_sbbot(sb);
+	for (bindex = 0; !err && bindex <= bbot; bindex++)
+		if (!bindex || is_sb_shared(sb, bindex, bindex - 1) < 0) {
+			br = au_sbr(sb, bindex);
+			xi = br->br_xino;
+			nfile = xi->xi_nfile;
+			for (i = 0; i < nfile; i++) {
+				file = au_xino_file(xi, i);
+				if (file)
+					err = do_xib_restore(sb, file, page);
+			}
+		} else
+			AuDbg("skip shared b%d\n", bindex);
+	free_page((unsigned long)page);
+
+out:
+	return err;
+}
+
+int au_xib_trunc(struct super_block *sb)
+{
+	int err;
+	ssize_t sz;
+	loff_t pos;
+	struct au_sbinfo *sbinfo;
+	unsigned long *p;
+	struct file *file;
+
+	SiMustWriteLock(sb);
+
+	err = 0;
+	sbinfo = au_sbi(sb);
+	if (!au_opt_test(sbinfo->si_mntflags, XINO))
+		goto out;
+
+	file = sbinfo->si_xib;
+	if (vfsub_f_size_read(file) <= PAGE_SIZE)
+		goto out;
+
+	file = au_xino_create2(sb, &sbinfo->si_xib->f_path, NULL);
+	err = PTR_ERR(file);
+	if (IS_ERR(file))
+		goto out;
+	fput(sbinfo->si_xib);
+	sbinfo->si_xib = file;
+
+	p = sbinfo->si_xib_buf;
+	memset(p, 0, PAGE_SIZE);
+	pos = 0;
+	sz = xino_fwrite(sbinfo->si_xib, p, PAGE_SIZE, &pos);
+	if (unlikely(sz != PAGE_SIZE)) {
+		err = sz;
+		AuIOErr("err %d\n", err);
+		if (sz >= 0)
+			err = -EIO;
+		goto out;
+	}
+
+	mutex_lock(&sbinfo->si_xib_mtx);
+	/* mnt_want_write() is unnecessary here */
+	err = xib_restore(sb);
+	mutex_unlock(&sbinfo->si_xib_mtx);
+
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+struct au_xino *au_xino_alloc(unsigned int nfile)
+{
+	struct au_xino *xi;
+
+	xi = kzalloc(sizeof(*xi), GFP_NOFS);
+	if (unlikely(!xi))
+		goto out;
+	xi->xi_nfile = nfile;
+	xi->xi_file = kcalloc(nfile, sizeof(*xi->xi_file), GFP_NOFS);
+	if (unlikely(!xi->xi_file))
+		goto out_free;
+
+	xi->xi_nondir.total = 8; /* initial size */
+	xi->xi_nondir.array = kcalloc(xi->xi_nondir.total, sizeof(ino_t),
+				      GFP_NOFS);
+	if (unlikely(!xi->xi_nondir.array))
+		goto out_file;
+
+	spin_lock_init(&xi->xi_nondir.spin);
+	init_waitqueue_head(&xi->xi_nondir.wqh);
+	mutex_init(&xi->xi_mtx);
+	INIT_HLIST_BL_HEAD(&xi->xi_writing);
+	atomic_set(&xi->xi_truncating, 0);
+	kref_init(&xi->xi_kref);
+	goto out; /* success */
+
+out_file:
+	au_kfree_try_rcu(xi->xi_file);
+out_free:
+	au_kfree_rcu(xi);
+	xi = NULL;
+out:
+	return xi;
+}
+
+static int au_xino_init(struct au_branch *br, int idx, struct file *file)
+{
+	int err;
+	struct au_xino *xi;
+
+	err = 0;
+	xi = au_xino_alloc(idx + 1);
+	if (unlikely(!xi)) {
+		err = -ENOMEM;
+		goto out;
+	}
+
+	if (file)
+		get_file(file);
+	xi->xi_file[idx] = file;
+	AuDebugOn(br->br_xino);
+	br->br_xino = xi;
+
+out:
+	return err;
+}
+
+static void au_xino_release(struct kref *kref)
+{
+	struct au_xino *xi;
+	int i;
+	unsigned long ul;
+	struct hlist_bl_head *hbl;
+	struct hlist_bl_node *pos, *n;
+	struct au_xi_writing *p;
+
+	xi = container_of(kref, struct au_xino, xi_kref);
+	for (i = 0; i < xi->xi_nfile; i++)
+		if (xi->xi_file[i])
+			fput(xi->xi_file[i]);
+	for (i = xi->xi_nondir.total - 1; i >= 0; i--)
+		AuDebugOn(xi->xi_nondir.array[i]);
+	mutex_destroy(&xi->xi_mtx);
+	hbl = &xi->xi_writing;
+	ul = au_hbl_count(hbl);
+	if (unlikely(ul)) {
+		pr_warn("xi_writing %lu\n", ul);
+		hlist_bl_lock(hbl);
+		hlist_bl_for_each_entry_safe(p, pos, n, hbl, node) {
+			hlist_bl_del(&p->node);
+			/* kmemleak reported au_kfree_rcu() doesn't free it */
+			kfree(p);
+		}
+		hlist_bl_unlock(hbl);
+	}
+	au_kfree_try_rcu(xi->xi_file);
+	au_kfree_try_rcu(xi->xi_nondir.array);
+	au_kfree_rcu(xi);
+}
+
+int au_xino_put(struct au_branch *br)
+{
+	int ret;
+	struct au_xino *xi;
+
+	ret = 0;
+	xi = br->br_xino;
+	if (xi) {
+		br->br_xino = NULL;
+		ret = kref_put(&xi->xi_kref, au_xino_release);
+	}
+
+	return ret;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * xino mount option handlers
+ */
+
+/* xino bitmap */
+static void xino_clear_xib(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	if (sbinfo->si_xib)
+		fput(sbinfo->si_xib);
+	sbinfo->si_xib = NULL;
+	if (sbinfo->si_xib_buf)
+		free_page((unsigned long)sbinfo->si_xib_buf);
+	sbinfo->si_xib_buf = NULL;
+}
+
+static int au_xino_set_xib(struct super_block *sb, struct path *path)
+{
+	int err;
+	loff_t pos;
+	struct au_sbinfo *sbinfo;
+	struct file *file;
+	struct super_block *xi_sb;
+
+	SiMustWriteLock(sb);
+
+	sbinfo = au_sbi(sb);
+	file = au_xino_create2(sb, path, sbinfo->si_xib);
+	err = PTR_ERR(file);
+	if (IS_ERR(file))
+		goto out;
+	if (sbinfo->si_xib)
+		fput(sbinfo->si_xib);
+	sbinfo->si_xib = file;
+	xi_sb = file_inode(file)->i_sb;
+	sbinfo->si_ximaxent = xi_sb->s_maxbytes;
+	if (unlikely(sbinfo->si_ximaxent < PAGE_SIZE)) {
+		err = -EIO;
+		pr_err("s_maxbytes(%llu) on %s is too small\n",
+		       (u64)sbinfo->si_ximaxent, au_sbtype(xi_sb));
+		goto out_unset;
+	}
+	sbinfo->si_ximaxent /= sizeof(ino_t);
+
+	err = -ENOMEM;
+	if (!sbinfo->si_xib_buf)
+		sbinfo->si_xib_buf = (void *)get_zeroed_page(GFP_NOFS);
+	if (unlikely(!sbinfo->si_xib_buf))
+		goto out_unset;
+
+	sbinfo->si_xib_last_pindex = 0;
+	sbinfo->si_xib_next_bit = 0;
+	if (vfsub_f_size_read(file) < PAGE_SIZE) {
+		pos = 0;
+		err = xino_fwrite(file, sbinfo->si_xib_buf, PAGE_SIZE, &pos);
+		if (unlikely(err != PAGE_SIZE))
+			goto out_free;
+	}
+	err = 0;
+	goto out; /* success */
+
+out_free:
+	if (sbinfo->si_xib_buf)
+		free_page((unsigned long)sbinfo->si_xib_buf);
+	sbinfo->si_xib_buf = NULL;
+	if (err >= 0)
+		err = -EIO;
+out_unset:
+	fput(sbinfo->si_xib);
+	sbinfo->si_xib = NULL;
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+/* xino for each branch */
+static void xino_clear_br(struct super_block *sb)
+{
+	aufs_bindex_t bindex, bbot;
+	struct au_branch *br;
+
+	bbot = au_sbbot(sb);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		AuDebugOn(!br);
+		au_xino_put(br);
+	}
+}
+
+static void au_xino_set_br_shared(struct super_block *sb, struct au_branch *br,
+				  aufs_bindex_t bshared)
+{
+	struct au_branch *brshared;
+
+	brshared = au_sbr(sb, bshared);
+	AuDebugOn(!brshared->br_xino);
+	AuDebugOn(!brshared->br_xino->xi_file);
+	if (br->br_xino != brshared->br_xino) {
+		au_xino_get(brshared);
+		au_xino_put(br);
+		br->br_xino = brshared->br_xino;
+	}
+}
+
+struct au_xino_do_set_br {
+	struct au_branch *br;
+	ino_t h_ino;
+	aufs_bindex_t bshared;
+};
+
+static int au_xino_do_set_br(struct super_block *sb, struct path *path,
+			     struct au_xino_do_set_br *args)
+{
+	int err;
+	struct au_xi_calc calc;
+	struct file *file;
+	struct au_branch *br;
+	struct au_xi_new xinew = {
+		.base = path
+	};
+
+	br = args->br;
+	xinew.xi = br->br_xino;
+	au_xi_calc(sb, args->h_ino, &calc);
+	xinew.copy_src = au_xino_file(xinew.xi, calc.idx);
+	if (args->bshared >= 0)
+		/* shared xino */
+		au_xino_set_br_shared(sb, br, args->bshared);
+	else if (!xinew.xi) {
+		/* new xino */
+		err = au_xino_init(br, calc.idx, xinew.copy_src);
+		if (unlikely(err))
+			goto out;
+	}
+
+	/* force re-creating */
+	xinew.xi = br->br_xino;
+	xinew.idx = calc.idx;
+	mutex_lock(&xinew.xi->xi_mtx);
+	file = au_xi_new(sb, &xinew);
+	mutex_unlock(&xinew.xi->xi_mtx);
+	err = PTR_ERR(file);
+	if (IS_ERR(file))
+		goto out;
+	AuDebugOn(!file);
+
+	err = au_xino_do_write(file, &calc, AUFS_ROOT_INO);
+	if (unlikely(err))
+		au_xino_put(br);
+
+out:
+	AuTraceErr(err);
+	return err;
+}
+
+static int au_xino_set_br(struct super_block *sb, struct path *path)
+{
+	int err;
+	aufs_bindex_t bindex, bbot;
+	struct au_xino_do_set_br args;
+	struct inode *inode;
+
+	SiMustWriteLock(sb);
+
+	bbot = au_sbbot(sb);
+	inode = d_inode(sb->s_root);
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		args.h_ino = au_h_iptr(inode, bindex)->i_ino;
+		args.br = au_sbr(sb, bindex);
+		args.bshared = is_sb_shared(sb, bindex, bindex - 1);
+		err = au_xino_do_set_br(sb, path, &args);
+		if (unlikely(err))
+			break;
+	}
+
+	AuTraceErr(err);
+	return err;
+}
+
+void au_xino_clr(struct super_block *sb)
+{
+	struct au_sbinfo *sbinfo;
+
+	au_xigen_clr(sb);
+	xino_clear_xib(sb);
+	xino_clear_br(sb);
+	dbgaufs_brs_del(sb, 0);
+	sbinfo = au_sbi(sb);
+	/* lvalue, do not call au_mntflags() */
+	au_opt_clr(sbinfo->si_mntflags, XINO);
+}
+
+int au_xino_set(struct super_block *sb, struct au_opt_xino *xiopt, int remount)
+{
+	int err, skip;
+	struct dentry *dentry, *parent, *cur_dentry, *cur_parent;
+	struct qstr *dname, *cur_name;
+	struct file *cur_xino;
+	struct au_sbinfo *sbinfo;
+	struct path *path, *cur_path;
+
+	SiMustWriteLock(sb);
+
+	err = 0;
+	sbinfo = au_sbi(sb);
+	path = &xiopt->file->f_path;
+	dentry = path->dentry;
+	parent = dget_parent(dentry);
+	if (remount) {
+		skip = 0;
+		cur_xino = sbinfo->si_xib;
+		if (cur_xino) {
+			cur_path = &cur_xino->f_path;
+			cur_dentry = cur_path->dentry;
+			cur_parent = dget_parent(cur_dentry);
+			cur_name = &cur_dentry->d_name;
+			dname = &dentry->d_name;
+			skip = (cur_parent == parent
+				&& au_qstreq(dname, cur_name));
+			dput(cur_parent);
+		}
+		if (skip)
+			goto out;
+	}
+
+	au_opt_set(sbinfo->si_mntflags, XINO);
+	err = au_xino_set_xib(sb, path);
+	/* si_x{read,write} are set */
+	if (!err)
+		err = au_xigen_set(sb, path);
+	if (!err)
+		err = au_xino_set_br(sb, path);
+	if (!err) {
+		dbgaufs_brs_add(sb, 0, /*topdown*/1);
+		goto out; /* success */
+	}
+
+	/* reset all */
+	AuIOErr("failed setting xino(%d).\n", err);
+	au_xino_clr(sb);
+
+out:
+	dput(parent);
+	return err;
+}
+
+/*
+ * create a xinofile at the default place/path.
+ */
+struct file *au_xino_def(struct super_block *sb)
+{
+	struct file *file;
+	char *page, *p;
+	struct au_branch *br;
+	struct super_block *h_sb;
+	struct path path;
+	aufs_bindex_t bbot, bindex, bwr;
+
+	br = NULL;
+	bbot = au_sbbot(sb);
+	bwr = -1;
+	for (bindex = 0; bindex <= bbot; bindex++) {
+		br = au_sbr(sb, bindex);
+		if (au_br_writable(br->br_perm)
+		    && !au_test_fs_bad_xino(au_br_sb(br))) {
+			bwr = bindex;
+			break;
+		}
+	}
+
+	if (bwr >= 0) {
+		file = ERR_PTR(-ENOMEM);
+		page = (void *)__get_free_page(GFP_NOFS);
+		if (unlikely(!page))
+			goto out;
+		path.mnt = au_br_mnt(br);
+		path.dentry = au_h_dptr(sb->s_root, bwr);
+		p = d_path(&path, page, PATH_MAX - sizeof(AUFS_XINO_FNAME));
+		file = (void *)p;
+		if (!IS_ERR(p)) {
+			strcat(p, "/" AUFS_XINO_FNAME);
+			AuDbg("%s\n", p);
+			file = au_xino_create(sb, p, /*silent*/0, /*wbrtop*/1);
+		}
+		free_page((unsigned long)page);
+	} else {
+		file = au_xino_create(sb, AUFS_XINO_DEFPATH, /*silent*/0,
+				      /*wbrtop*/0);
+		if (IS_ERR(file))
+			goto out;
+		h_sb = file->f_path.dentry->d_sb;
+		if (unlikely(au_test_fs_bad_xino(h_sb))) {
+			pr_err("xino doesn't support %s(%s)\n",
+			       AUFS_XINO_DEFPATH, au_sbtype(h_sb));
+			fput(file);
+			file = ERR_PTR(-EINVAL);
+		}
+	}
+
+out:
+	return file;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * initialize the xinofile for the specified branch @br
+ * at the place/path where @base_file indicates.
+ * test whether another branch is on the same filesystem or not,
+ * if found then share the xinofile with another branch.
+ */
+int au_xino_init_br(struct super_block *sb, struct au_branch *br, ino_t h_ino,
+		    struct path *base)
+{
+	int err;
+	struct au_xino_do_set_br args = {
+		.h_ino	= h_ino,
+		.br	= br
+	};
+
+	args.bshared = sbr_find_shared(sb, /*btop*/0, au_sbbot(sb),
+				       au_br_sb(br));
+	err = au_xino_do_set_br(sb, base, &args);
+	if (unlikely(err))
+		au_xino_put(br);
+
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/*
+ * get an unused inode number from bitmap
+ */
+ino_t au_xino_new_ino(struct super_block *sb)
+{
+	ino_t ino;
+	unsigned long *p, pindex, ul, pend;
+	struct au_sbinfo *sbinfo;
+	struct file *file;
+	int free_bit, err;
+
+	if (!au_opt_test(au_mntflags(sb), XINO))
+		return iunique(sb, AUFS_FIRST_INO);
+
+	sbinfo = au_sbi(sb);
+	mutex_lock(&sbinfo->si_xib_mtx);
+	p = sbinfo->si_xib_buf;
+	free_bit = sbinfo->si_xib_next_bit;
+	if (free_bit < page_bits && !test_bit(free_bit, p))
+		goto out; /* success */
+	free_bit = find_first_zero_bit(p, page_bits);
+	if (free_bit < page_bits)
+		goto out; /* success */
+
+	pindex = sbinfo->si_xib_last_pindex;
+	for (ul = pindex - 1; ul < ULONG_MAX; ul--) {
+		err = xib_pindex(sb, ul);
+		if (unlikely(err))
+			goto out_err;
+		free_bit = find_first_zero_bit(p, page_bits);
+		if (free_bit < page_bits)
+			goto out; /* success */
+	}
+
+	file = sbinfo->si_xib;
+	pend = vfsub_f_size_read(file) / PAGE_SIZE;
+	for (ul = pindex + 1; ul <= pend; ul++) {
+		err = xib_pindex(sb, ul);
+		if (unlikely(err))
+			goto out_err;
+		free_bit = find_first_zero_bit(p, page_bits);
+		if (free_bit < page_bits)
+			goto out; /* success */
+	}
+	BUG();
+
+out:
+	set_bit(free_bit, p);
+	sbinfo->si_xib_next_bit = free_bit + 1;
+	pindex = sbinfo->si_xib_last_pindex;
+	mutex_unlock(&sbinfo->si_xib_mtx);
+	ino = xib_calc_ino(pindex, free_bit);
+	AuDbg("i%lu\n", (unsigned long)ino);
+	return ino;
+out_err:
+	mutex_unlock(&sbinfo->si_xib_mtx);
+	AuDbg("i0\n");
+	return 0;
+}
+
+/* for s_op->delete_inode() */
+void au_xino_delete_inode(struct inode *inode, const int unlinked)
+{
+	int err;
+	unsigned int mnt_flags;
+	aufs_bindex_t bindex, bbot, bi;
+	unsigned char try_trunc;
+	struct au_iinfo *iinfo;
+	struct super_block *sb;
+	struct au_hinode *hi;
+	struct inode *h_inode;
+	struct au_branch *br;
+	struct au_xi_calc calc;
+	struct file *file;
+
+	AuDebugOn(au_is_bad_inode(inode));
+
+	sb = inode->i_sb;
+	mnt_flags = au_mntflags(sb);
+	if (!au_opt_test(mnt_flags, XINO)
+	    || inode->i_ino == AUFS_ROOT_INO)
+		return;
+
+	if (unlinked) {
+		au_xigen_inc(inode);
+		au_xib_clear_bit(inode);
+	}
+
+	iinfo = au_ii(inode);
+	bindex = iinfo->ii_btop;
+	if (bindex < 0)
+		return;
+
+	try_trunc = !!au_opt_test(mnt_flags, TRUNC_XINO);
+	hi = au_hinode(iinfo, bindex);
+	bbot = iinfo->ii_bbot;
+	for (; bindex <= bbot; bindex++, hi++) {
+		h_inode = hi->hi_inode;
+		if (!h_inode
+		    || (!unlinked && h_inode->i_nlink))
+			continue;
+
+		/* inode may not be revalidated */
+		bi = au_br_index(sb, hi->hi_id);
+		if (bi < 0)
+			continue;
+
+		br = au_sbr(sb, bi);
+		au_xi_calc(sb, h_inode->i_ino, &calc);
+		file = au_xino_file(br->br_xino, calc.idx);
+		if (IS_ERR_OR_NULL(file))
+			continue;
+
+		err = au_xino_do_write(file, &calc, /*ino*/0);
+		if (!err && try_trunc
+		    && au_test_fs_trunc_xino(au_br_sb(br)))
+			xino_try_trunc(sb, br);
+	}
+}
+
+/* ---------------------------------------------------------------------- */
+
+static int au_xinondir_find(struct au_xino *xi, ino_t h_ino)
+{
+	int found, total, i;
+
+	found = -1;
+	total = xi->xi_nondir.total;
+	for (i = 0; i < total; i++) {
+		if (xi->xi_nondir.array[i] != h_ino)
+			continue;
+		found = i;
+		break;
+	}
+
+	return found;
+}
+
+static int au_xinondir_expand(struct au_xino *xi)
+{
+	int err, sz;
+	ino_t *p;
+
+	BUILD_BUG_ON(KMALLOC_MAX_SIZE > INT_MAX);
+
+	err = -ENOMEM;
+	sz = xi->xi_nondir.total * sizeof(ino_t);
+	if (unlikely(sz > KMALLOC_MAX_SIZE / 2))
+		goto out;
+	p = au_kzrealloc(xi->xi_nondir.array, sz, sz << 1, GFP_ATOMIC,
+			 /*may_shrink*/0);
+	if (p) {
+		xi->xi_nondir.array = p;
+		xi->xi_nondir.total <<= 1;
+		AuDbg("xi_nondir.total %d\n", xi->xi_nondir.total);
+		err = 0;
+	}
+
+out:
+	return err;
+}
+
+void au_xinondir_leave(struct super_block *sb, aufs_bindex_t bindex,
+		       ino_t h_ino, int idx)
+{
+	struct au_xino *xi;
+
+	AuDebugOn(!au_opt_test(au_mntflags(sb), XINO));
+	xi = au_sbr(sb, bindex)->br_xino;
+	AuDebugOn(idx < 0 || xi->xi_nondir.total <= idx);
+
+	spin_lock(&xi->xi_nondir.spin);
+	AuDebugOn(xi->xi_nondir.array[idx] != h_ino);
+	xi->xi_nondir.array[idx] = 0;
+	spin_unlock(&xi->xi_nondir.spin);
+	wake_up_all(&xi->xi_nondir.wqh);
+}
+
+int au_xinondir_enter(struct super_block *sb, aufs_bindex_t bindex, ino_t h_ino,
+		      int *idx)
+{
+	int err, found, empty;
+	struct au_xino *xi;
+
+	err = 0;
+	*idx = -1;
+	if (!au_opt_test(au_mntflags(sb), XINO))
+		goto out; /* no xino */
+
+	xi = au_sbr(sb, bindex)->br_xino;
+
+again:
+	spin_lock(&xi->xi_nondir.spin);
+	found = au_xinondir_find(xi, h_ino);
+	if (found == -1) {
+		empty = au_xinondir_find(xi, /*h_ino*/0);
+		if (empty == -1) {
+			empty = xi->xi_nondir.total;
+			err = au_xinondir_expand(xi);
+			if (unlikely(err))
+				goto out_unlock;
+		}
+		xi->xi_nondir.array[empty] = h_ino;
+		*idx = empty;
+	} else {
+		spin_unlock(&xi->xi_nondir.spin);
+		wait_event(xi->xi_nondir.wqh,
+			   xi->xi_nondir.array[found] != h_ino);
+		goto again;
+	}
+
+out_unlock:
+	spin_unlock(&xi->xi_nondir.spin);
+out:
+	return err;
+}
+
+/* ---------------------------------------------------------------------- */
+
+int au_xino_path(struct seq_file *seq, struct file *file)
+{
+	int err;
+
+	err = au_seq_path(seq, &file->f_path);
+	if (unlikely(err))
+		goto out;
+
+#define Deleted "\\040(deleted)"
+	seq->count -= sizeof(Deleted) - 1;
+	AuDebugOn(memcmp(seq->buf + seq->count, Deleted,
+			 sizeof(Deleted) - 1));
+#undef Deleted
+
+out:
+	return err;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/autofs/waitq.c
+++ linux-xilinx-zynqmp-5.15.0/fs/autofs/waitq.c
@@ -32,8 +32,9 @@
 		wq->status = -ENOENT; /* Magic is gone - report failure */
 		kfree(wq->name.name - wq->offset);
 		wq->name.name = NULL;
-		wq->wait_ctr--;
 		wake_up_interruptible(&wq->queue);
+		if (!--wq->wait_ctr)
+			kfree(wq);
 		wq = nwq;
 	}
 	fput(sbi->pipe);	/* Close the pipe */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/binfmt_elf.c
+++ linux-xilinx-zynqmp-5.15.0/fs/binfmt_elf.c
@@ -170,8 +170,8 @@
 
 static int
 create_elf_tables(struct linux_binprm *bprm, const struct elfhdr *exec,
-		unsigned long load_addr, unsigned long interp_load_addr,
-		unsigned long e_entry)
+		unsigned long interp_load_addr,
+		unsigned long e_entry, unsigned long phdr_addr)
 {
 	struct mm_struct *mm = current->mm;
 	unsigned long p = bprm->p;
@@ -257,7 +257,7 @@
 	NEW_AUX_ENT(AT_HWCAP, ELF_HWCAP);
 	NEW_AUX_ENT(AT_PAGESZ, ELF_EXEC_PAGESIZE);
 	NEW_AUX_ENT(AT_CLKTCK, CLOCKS_PER_SEC);
-	NEW_AUX_ENT(AT_PHDR, load_addr + exec->e_phoff);
+	NEW_AUX_ENT(AT_PHDR, phdr_addr);
 	NEW_AUX_ENT(AT_PHENT, sizeof(struct elf_phdr));
 	NEW_AUX_ENT(AT_PHNUM, exec->e_phnum);
 	NEW_AUX_ENT(AT_BASE, interp_load_addr);
@@ -823,7 +823,7 @@
 static int load_elf_binary(struct linux_binprm *bprm)
 {
 	struct file *interpreter = NULL; /* to shut gcc up */
- 	unsigned long load_addr = 0, load_bias = 0;
+	unsigned long load_addr, load_bias = 0, phdr_addr = 0;
 	int load_addr_set = 0;
 	unsigned long error;
 	struct elf_phdr *elf_ppnt, *elf_phdata, *interp_elf_phdata = NULL;
@@ -910,7 +910,7 @@
 		interp_elf_ex = kmalloc(sizeof(*interp_elf_ex), GFP_KERNEL);
 		if (!interp_elf_ex) {
 			retval = -ENOMEM;
-			goto out_free_ph;
+			goto out_free_file;
 		}
 
 		/* Get the exec headers */
@@ -1008,7 +1008,8 @@
 	if (elf_read_implies_exec(*elf_ex, executable_stack))
 		current->personality |= READ_IMPLIES_EXEC;
 
-	if (!(current->personality & ADDR_NO_RANDOMIZE) && randomize_va_space)
+	const int snapshot_randomize_va_space = READ_ONCE(randomize_va_space);
+	if (!(current->personality & ADDR_NO_RANDOMIZE) && snapshot_randomize_va_space)
 		current->flags |= PF_RANDOMIZE;
 
 	setup_new_exec(bprm);
@@ -1156,6 +1157,17 @@
 				reloc_func_desc = load_bias;
 			}
 		}
+
+		/*
+		 * Figure out which segment in the file contains the Program
+		 * Header table, and map to the associated memory address.
+		 */
+		if (elf_ppnt->p_offset <= elf_ex->e_phoff &&
+		    elf_ex->e_phoff < elf_ppnt->p_offset + elf_ppnt->p_filesz) {
+			phdr_addr = elf_ex->e_phoff - elf_ppnt->p_offset +
+				    elf_ppnt->p_vaddr;
+		}
+
 		k = elf_ppnt->p_vaddr;
 		if ((elf_ppnt->p_flags & PF_X) && k < start_code)
 			start_code = k;
@@ -1191,6 +1203,7 @@
 	}
 
 	e_entry = elf_ex->e_entry + load_bias;
+	phdr_addr += load_bias;
 	elf_bss += load_bias;
 	elf_brk += load_bias;
 	start_code += load_bias;
@@ -1254,8 +1267,8 @@
 		goto out;
 #endif /* ARCH_HAS_SETUP_ADDITIONAL_PAGES */
 
-	retval = create_elf_tables(bprm, elf_ex,
-			  load_addr, interp_load_addr, e_entry);
+	retval = create_elf_tables(bprm, elf_ex, interp_load_addr,
+				   e_entry, phdr_addr);
 	if (retval < 0)
 		goto out;
 
@@ -1266,7 +1279,7 @@
 	mm->end_data = end_data;
 	mm->start_stack = bprm->p;
 
-	if ((current->flags & PF_RANDOMIZE) && (randomize_va_space > 1)) {
+	if ((current->flags & PF_RANDOMIZE) && (snapshot_randomize_va_space > 1)) {
 		/*
 		 * For architectures with ELF randomization, when executing
 		 * a loader directly (i.e. no interpreter listed in ELF
@@ -1319,6 +1332,7 @@
 out_free_dentry:
 	kfree(interp_elf_ex);
 	kfree(interp_elf_phdata);
+out_free_file:
 	allow_write_access(interpreter);
 	if (interpreter)
 		fput(interpreter);
@@ -1606,17 +1620,16 @@
  *   long file_ofs
  * followed by COUNT filenames in ASCII: "FILE1" NUL "FILE2" NUL...
  */
-static int fill_files_note(struct memelfnote *note)
+static int fill_files_note(struct memelfnote *note, struct coredump_params *cprm)
 {
-	struct mm_struct *mm = current->mm;
-	struct vm_area_struct *vma;
 	unsigned count, size, names_ofs, remaining, n;
 	user_long_t *data;
 	user_long_t *start_end_ofs;
 	char *name_base, *name_curpos;
+	int i;
 
 	/* *Estimated* file count and total data size needed */
-	count = mm->map_count;
+	count = cprm->vma_count;
 	if (count > UINT_MAX / 64)
 		return -EINVAL;
 	size = count * 64;
@@ -1638,11 +1651,12 @@
 	name_base = name_curpos = ((char *)data) + names_ofs;
 	remaining = size - names_ofs;
 	count = 0;
-	for (vma = mm->mmap; vma != NULL; vma = vma->vm_next) {
+	for (i = 0; i < cprm->vma_count; i++) {
+		struct core_vma_metadata *m = &cprm->vma_meta[i];
 		struct file *file;
 		const char *filename;
 
-		file = vma->vm_file;
+		file = m->file;
 		if (!file)
 			continue;
 		filename = file_path(file, name_curpos, remaining);
@@ -1662,9 +1676,9 @@
 		memmove(name_curpos, filename, n);
 		name_curpos += n;
 
-		*start_end_ofs++ = vma->vm_start;
-		*start_end_ofs++ = vma->vm_end;
-		*start_end_ofs++ = vma->vm_pgoff;
+		*start_end_ofs++ = m->start;
+		*start_end_ofs++ = m->end;
+		*start_end_ofs++ = m->pgoff;
 		count++;
 	}
 
@@ -1675,7 +1689,7 @@
 	 * Count usually is less than mm->map_count,
 	 * we need to move filenames down.
 	 */
-	n = mm->map_count - count;
+	n = cprm->vma_count - count;
 	if (n != 0) {
 		unsigned shift_bytes = n * 3 * sizeof(data[0]);
 		memmove(name_base - shift_bytes, name_base,
@@ -1787,7 +1801,7 @@
 
 static int fill_note_info(struct elfhdr *elf, int phdrs,
 			  struct elf_note_info *info,
-			  const kernel_siginfo_t *siginfo, struct pt_regs *regs)
+			  struct coredump_params *cprm)
 {
 	struct task_struct *dump_task = current;
 	const struct user_regset_view *view = task_user_regset_view(dump_task);
@@ -1859,7 +1873,7 @@
 	 * Now fill in each thread's information.
 	 */
 	for (t = info->thread; t != NULL; t = t->next)
-		if (!fill_thread_core_info(t, view, siginfo->si_signo, &info->size))
+		if (!fill_thread_core_info(t, view, cprm->siginfo->si_signo, &info->size))
 			return 0;
 
 	/*
@@ -1868,13 +1882,13 @@
 	fill_psinfo(psinfo, dump_task->group_leader, dump_task->mm);
 	info->size += notesize(&info->psinfo);
 
-	fill_siginfo_note(&info->signote, &info->csigdata, siginfo);
+	fill_siginfo_note(&info->signote, &info->csigdata, cprm->siginfo);
 	info->size += notesize(&info->signote);
 
 	fill_auxv_note(&info->auxv, current->mm);
 	info->size += notesize(&info->auxv);
 
-	if (fill_files_note(&info->files) == 0)
+	if (fill_files_note(&info->files, cprm) == 0)
 		info->size += notesize(&info->files);
 
 	return 1;
@@ -2016,7 +2030,7 @@
 
 static int fill_note_info(struct elfhdr *elf, int phdrs,
 			  struct elf_note_info *info,
-			  const kernel_siginfo_t *siginfo, struct pt_regs *regs)
+			  struct coredump_params *cprm)
 {
 	struct core_thread *ct;
 	struct elf_thread_status *ets;
@@ -2037,13 +2051,13 @@
 	list_for_each_entry(ets, &info->thread_list, list) {
 		int sz;
 
-		sz = elf_dump_thread_status(siginfo->si_signo, ets);
+		sz = elf_dump_thread_status(cprm->siginfo->si_signo, ets);
 		info->thread_status_size += sz;
 	}
 	/* now collect the dump for the current */
 	memset(info->prstatus, 0, sizeof(*info->prstatus));
-	fill_prstatus(&info->prstatus->common, current, siginfo->si_signo);
-	elf_core_copy_regs(&info->prstatus->pr_reg, regs);
+	fill_prstatus(&info->prstatus->common, current, cprm->siginfo->si_signo);
+	elf_core_copy_regs(&info->prstatus->pr_reg, cprm->regs);
 
 	/* Set up header */
 	fill_elf_header(elf, phdrs, ELF_ARCH, ELF_CORE_EFLAGS);
@@ -2059,18 +2073,18 @@
 	fill_note(info->notes + 1, "CORE", NT_PRPSINFO,
 		  sizeof(*info->psinfo), info->psinfo);
 
-	fill_siginfo_note(info->notes + 2, &info->csigdata, siginfo);
+	fill_siginfo_note(info->notes + 2, &info->csigdata, cprm->siginfo);
 	fill_auxv_note(info->notes + 3, current->mm);
 	info->numnote = 4;
 
-	if (fill_files_note(info->notes + info->numnote) == 0) {
+	if (fill_files_note(info->notes + info->numnote, cprm) == 0) {
 		info->notes_files = info->notes + info->numnote;
 		info->numnote++;
 	}
 
 	/* Try to dump the FPU. */
-	info->prstatus->pr_fpvalid = elf_core_copy_task_fpregs(current, regs,
-							       info->fpu);
+	info->prstatus->pr_fpvalid =
+		elf_core_copy_task_fpregs(current, cprm->regs, info->fpu);
 	if (info->prstatus->pr_fpvalid)
 		fill_note(info->notes + info->numnote++,
 			  "CORE", NT_PRFPREG, sizeof(*info->fpu), info->fpu);
@@ -2156,8 +2170,7 @@
 static int elf_core_dump(struct coredump_params *cprm)
 {
 	int has_dumped = 0;
-	int vma_count, segs, i;
-	size_t vma_data_size;
+	int segs, i;
 	struct elfhdr elf;
 	loff_t offset = 0, dataoff;
 	struct elf_note_info info = { };
@@ -2165,16 +2178,12 @@
 	struct elf_shdr *shdr4extnum = NULL;
 	Elf_Half e_phnum;
 	elf_addr_t e_shoff;
-	struct core_vma_metadata *vma_meta;
-
-	if (dump_vma_snapshot(cprm, &vma_count, &vma_meta, &vma_data_size))
-		return 0;
 
 	/*
 	 * The number of segs are recored into ELF header as 16bit value.
 	 * Please check DEFAULT_MAX_MAP_COUNT definition when you modify here.
 	 */
-	segs = vma_count + elf_core_extra_phdrs();
+	segs = cprm->vma_count + elf_core_extra_phdrs();
 
 	/* for notes section */
 	segs++;
@@ -2188,7 +2197,7 @@
 	 * Collect all the non-memory information about the process for the
 	 * notes.  This also sets up the file header.
 	 */
-	if (!fill_note_info(&elf, e_phnum, &info, cprm->siginfo, cprm->regs))
+	if (!fill_note_info(&elf, e_phnum, &info, cprm))
 		goto end_coredump;
 
 	has_dumped = 1;
@@ -2213,7 +2222,7 @@
 
 	dataoff = offset = roundup(offset, ELF_EXEC_PAGESIZE);
 
-	offset += vma_data_size;
+	offset += cprm->vma_data_size;
 	offset += elf_core_extra_data_size();
 	e_shoff = offset;
 
@@ -2233,8 +2242,8 @@
 		goto end_coredump;
 
 	/* Write program headers for segments dump */
-	for (i = 0; i < vma_count; i++) {
-		struct core_vma_metadata *meta = vma_meta + i;
+	for (i = 0; i < cprm->vma_count; i++) {
+		struct core_vma_metadata *meta = cprm->vma_meta + i;
 		struct elf_phdr phdr;
 
 		phdr.p_type = PT_LOAD;
@@ -2271,8 +2280,8 @@
 	/* Align to page */
 	dump_skip_to(cprm, dataoff);
 
-	for (i = 0; i < vma_count; i++) {
-		struct core_vma_metadata *meta = vma_meta + i;
+	for (i = 0; i < cprm->vma_count; i++) {
+		struct core_vma_metadata *meta = cprm->vma_meta + i;
 
 		if (!dump_user_range(cprm, meta->start, meta->dump_size))
 			goto end_coredump;
@@ -2289,7 +2298,6 @@
 end_coredump:
 	free_note_info(&info);
 	kfree(shdr4extnum);
-	kvfree(vma_meta);
 	kfree(phdr4note);
 	return has_dumped;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/binfmt_elf_fdpic.c
+++ linux-xilinx-zynqmp-5.15.0/fs/binfmt_elf_fdpic.c
@@ -320,7 +320,7 @@
 	else
 		executable_stack = EXSTACK_DEFAULT;
 
-	if (stack_size == 0) {
+	if (stack_size == 0 && interp_params.flags & ELF_FDPIC_FLAG_PRESENT) {
 		stack_size = interp_params.stack_size;
 		if (interp_params.flags & ELF_FDPIC_FLAG_EXEC_STACK)
 			executable_stack = EXSTACK_ENABLE_X;
@@ -345,10 +345,9 @@
 	/* there's now no turning back... the old userspace image is dead,
 	 * defunct, deceased, etc.
 	 */
+	SET_PERSONALITY(exec_params.hdr);
 	if (elf_check_fdpic(&exec_params.hdr))
-		set_personality(PER_LINUX_FDPIC);
-	else
-		set_personality(PER_LINUX);
+		current->personality |= PER_LINUX_FDPIC;
 	if (elf_read_implies_exec(&exec_params.hdr, executable_stack))
 		current->personality |= READ_IMPLIES_EXEC;
 
@@ -434,8 +433,9 @@
 	current->mm->start_stack = current->mm->start_brk + stack_size;
 #endif
 
-	if (create_elf_fdpic_tables(bprm, current->mm,
-				    &exec_params, &interp_params) < 0)
+	retval = create_elf_fdpic_tables(bprm, current->mm, &exec_params,
+					 &interp_params);
+	if (retval < 0)
 		goto error;
 
 	kdebug("- start_code  %lx", current->mm->start_code);
@@ -1465,7 +1465,7 @@
 static int elf_fdpic_core_dump(struct coredump_params *cprm)
 {
 	int has_dumped = 0;
-	int vma_count, segs;
+	int segs;
 	int i;
 	struct elfhdr *elf = NULL;
 	loff_t offset = 0, dataoff;
@@ -1480,8 +1480,6 @@
 	elf_addr_t e_shoff;
 	struct core_thread *ct;
 	struct elf_thread_status *tmp;
-	struct core_vma_metadata *vma_meta = NULL;
-	size_t vma_data_size;
 
 	/* alloc memory for large data structures: too large to be on stack */
 	elf = kmalloc(sizeof(*elf), GFP_KERNEL);
@@ -1491,9 +1489,6 @@
 	if (!psinfo)
 		goto end_coredump;
 
-	if (dump_vma_snapshot(cprm, &vma_count, &vma_meta, &vma_data_size))
-		goto end_coredump;
-
 	for (ct = current->mm->core_state->dumper.next;
 					ct; ct = ct->next) {
 		tmp = elf_dump_thread_status(cprm->siginfo->si_signo,
@@ -1513,7 +1508,7 @@
 	tmp->next = thread_list;
 	thread_list = tmp;
 
-	segs = vma_count + elf_core_extra_phdrs();
+	segs = cprm->vma_count + elf_core_extra_phdrs();
 
 	/* for notes section */
 	segs++;
@@ -1558,7 +1553,7 @@
 	/* Page-align dumped data */
 	dataoff = offset = roundup(offset, ELF_EXEC_PAGESIZE);
 
-	offset += vma_data_size;
+	offset += cprm->vma_data_size;
 	offset += elf_core_extra_data_size();
 	e_shoff = offset;
 
@@ -1578,8 +1573,8 @@
 		goto end_coredump;
 
 	/* write program headers for segments dump */
-	for (i = 0; i < vma_count; i++) {
-		struct core_vma_metadata *meta = vma_meta + i;
+	for (i = 0; i < cprm->vma_count; i++) {
+		struct core_vma_metadata *meta = cprm->vma_meta + i;
 		struct elf_phdr phdr;
 		size_t sz;
 
@@ -1628,7 +1623,7 @@
 
 	dump_skip_to(cprm, dataoff);
 
-	if (!elf_fdpic_dump_segments(cprm, vma_meta, vma_count))
+	if (!elf_fdpic_dump_segments(cprm, cprm->vma_meta, cprm->vma_count))
 		goto end_coredump;
 
 	if (!elf_core_write_extra_data(cprm))
@@ -1652,7 +1647,6 @@
 		thread_list = thread_list->next;
 		kfree(tmp);
 	}
-	kvfree(vma_meta);
 	kfree(phdr4note);
 	kfree(elf);
 	kfree(psinfo);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/binfmt_flat.c
+++ linux-xilinx-zynqmp-5.15.0/fs/binfmt_flat.c
@@ -76,8 +76,10 @@
 
 #ifdef CONFIG_BINFMT_FLAT_NO_DATA_START_OFFSET
 #define DATA_START_OFFSET_WORDS		(0)
+#define MAX_SHARED_LIBS_UPDATE		(0)
 #else
 #define DATA_START_OFFSET_WORDS		(MAX_SHARED_LIBS)
+#define MAX_SHARED_LIBS_UPDATE		(MAX_SHARED_LIBS)
 #endif
 
 struct lib_info {
@@ -433,6 +435,30 @@
 
 /****************************************************************************/
 
+static inline u32 __user *skip_got_header(u32 __user *rp)
+{
+	if (IS_ENABLED(CONFIG_RISCV)) {
+		/*
+		 * RISC-V has a 16 byte GOT PLT header for elf64-riscv
+		 * and 8 byte GOT PLT header for elf32-riscv.
+		 * Skip the whole GOT PLT header, since it is reserved
+		 * for the dynamic linker (ld.so).
+		 */
+		u32 rp_val0, rp_val1;
+
+		if (get_user(rp_val0, rp))
+			return rp;
+		if (get_user(rp_val1, rp + 1))
+			return rp;
+
+		if (rp_val0 == 0xffffffff && rp_val1 == 0xffffffff)
+			rp += 4;
+		else if (rp_val0 == 0xffffffff)
+			rp += 2;
+	}
+	return rp;
+}
+
 static int load_flat_file(struct linux_binprm *bprm,
 		struct lib_info *libinfo, int id, unsigned long *extra_stack)
 {
@@ -516,7 +542,7 @@
 	 * 28 bits (256 MB) is way more than reasonable in this case.
 	 * If some top bits are set we have probable binary corruption.
 	*/
-	if ((text_len | data_len | bss_len | stack_len | full_data) >> 28) {
+	if ((text_len | data_len | bss_len | stack_len | relocs | full_data) >> 28) {
 		pr_err("bad header\n");
 		ret = -ENOEXEC;
 		goto err;
@@ -782,7 +808,8 @@
 	 * image.
 	 */
 	if (flags & FLAT_FLAG_GOTPIC) {
-		for (rp = (u32 __user *)datapos; ; rp++) {
+		rp = skip_got_header((u32 __user *) datapos);
+		for (; ; rp++) {
 			u32 addr, rp_val;
 			if (get_user(rp_val, rp))
 				return -EFAULT;
@@ -966,7 +993,7 @@
 		return res;
 
 	/* Update data segment pointers for all libraries */
-	for (i = 0; i < MAX_SHARED_LIBS; i++) {
+	for (i = 0; i < MAX_SHARED_LIBS_UPDATE; i++) {
 		if (!libinfo.lib_list[i].loaded)
 			continue;
 		for (j = 0; j < MAX_SHARED_LIBS; j++) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/binfmt_misc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/binfmt_misc.c
@@ -44,10 +44,10 @@
 static int enabled = 1;
 
 enum {Enabled, Magic};
-#define MISC_FMT_PRESERVE_ARGV0 (1 << 31)
-#define MISC_FMT_OPEN_BINARY (1 << 30)
-#define MISC_FMT_CREDENTIALS (1 << 29)
-#define MISC_FMT_OPEN_FILE (1 << 28)
+#define MISC_FMT_PRESERVE_ARGV0 (1UL << 31)
+#define MISC_FMT_OPEN_BINARY (1UL << 30)
+#define MISC_FMT_CREDENTIALS (1UL << 29)
+#define MISC_FMT_OPEN_FILE (1UL << 28)
 
 typedef struct {
 	struct list_head list;
@@ -60,12 +60,11 @@
 	char *name;
 	struct dentry *dentry;
 	struct file *interp_file;
+	refcount_t users;		/* sync removal with load_misc_binary() */
 } Node;
 
 static DEFINE_RWLOCK(entries_lock);
 static struct file_system_type bm_fs_type;
-static struct vfsmount *bm_mnt;
-static int entry_count;
 
 /*
  * Max length of the register string.  Determined by:
@@ -82,19 +81,23 @@
  */
 #define MAX_REGISTER_LENGTH 1920
 
-/*
- * Check if we support the binfmt
- * if we do, return the node, else NULL
- * locking is done in load_misc_binary
+/**
+ * search_binfmt_handler - search for a binary handler for @bprm
+ * @misc: handle to binfmt_misc instance
+ * @bprm: binary for which we are looking for a handler
+ *
+ * Search for a binary type handler for @bprm in the list of registered binary
+ * type handlers.
+ *
+ * Return: binary type list entry on success, NULL on failure
  */
-static Node *check_file(struct linux_binprm *bprm)
+static Node *search_binfmt_handler(struct linux_binprm *bprm)
 {
 	char *p = strrchr(bprm->interp, '.');
-	struct list_head *l;
+	Node *e;
 
 	/* Walk all the registered handlers. */
-	list_for_each(l, &entries) {
-		Node *e = list_entry(l, Node, list);
+	list_for_each_entry(e, &entries, list) {
 		char *s;
 		int j;
 
@@ -123,9 +126,49 @@
 		if (j == e->size)
 			return e;
 	}
+
 	return NULL;
 }
 
+/**
+ * get_binfmt_handler - try to find a binary type handler
+ * @misc: handle to binfmt_misc instance
+ * @bprm: binary for which we are looking for a handler
+ *
+ * Try to find a binfmt handler for the binary type. If one is found take a
+ * reference to protect against removal via bm_{entry,status}_write().
+ *
+ * Return: binary type list entry on success, NULL on failure
+ */
+static Node *get_binfmt_handler(struct linux_binprm *bprm)
+{
+	Node *e;
+
+	read_lock(&entries_lock);
+	e = search_binfmt_handler(bprm);
+	if (e)
+		refcount_inc(&e->users);
+	read_unlock(&entries_lock);
+	return e;
+}
+
+/**
+ * put_binfmt_handler - put binary handler node
+ * @e: node to put
+ *
+ * Free node syncing with load_misc_binary() and defer final free to
+ * load_misc_binary() in case it is using the binary type handler we were
+ * requested to remove.
+ */
+static void put_binfmt_handler(Node *e)
+{
+	if (refcount_dec_and_test(&e->users)) {
+		if (e->flags & MISC_FMT_OPEN_FILE)
+			filp_close(e->interp_file, NULL);
+		kfree(e);
+	}
+}
+
 /*
  * the loader itself
  */
@@ -139,12 +182,7 @@
 	if (!enabled)
 		return retval;
 
-	/* to keep locking time low, we copy the interpreter string */
-	read_lock(&entries_lock);
-	fmt = check_file(bprm);
-	if (fmt)
-		dget(fmt->dentry);
-	read_unlock(&entries_lock);
+	fmt = get_binfmt_handler(bprm);
 	if (!fmt)
 		return retval;
 
@@ -198,7 +236,16 @@
 
 	retval = 0;
 ret:
-	dput(fmt->dentry);
+
+	/*
+	 * If we actually put the node here all concurrent calls to
+	 * load_misc_binary() will have finished. We also know
+	 * that for the refcount to be zero ->evict_inode() must have removed
+	 * the node to be deleted from the list. All that is left for us is to
+	 * close and free.
+	 */
+	put_binfmt_handler(fmt);
+
 	return retval;
 }
 
@@ -553,30 +600,90 @@
 	return inode;
 }
 
+/**
+ * bm_evict_inode - cleanup data associated with @inode
+ * @inode: inode to which the data is attached
+ *
+ * Cleanup the binary type handler data associated with @inode if a binary type
+ * entry is removed or the filesystem is unmounted and the super block is
+ * shutdown.
+ *
+ * If the ->evict call was not caused by a super block shutdown but by a write
+ * to remove the entry or all entries via bm_{entry,status}_write() the entry
+ * will have already been removed from the list. We keep the list_empty() check
+ * to make that explicit.
+*/
 static void bm_evict_inode(struct inode *inode)
 {
 	Node *e = inode->i_private;
 
-	if (e && e->flags & MISC_FMT_OPEN_FILE)
-		filp_close(e->interp_file, NULL);
-
 	clear_inode(inode);
-	kfree(e);
+
+	if (e) {
+		write_lock(&entries_lock);
+		if (!list_empty(&e->list))
+			list_del_init(&e->list);
+		write_unlock(&entries_lock);
+		put_binfmt_handler(e);
+	}
 }
 
-static void kill_node(Node *e)
+/**
+ * unlink_binfmt_dentry - remove the dentry for the binary type handler
+ * @dentry: dentry associated with the binary type handler
+ *
+ * Do the actual filesystem work to remove a dentry for a registered binary
+ * type handler. Since binfmt_misc only allows simple files to be created
+ * directly under the root dentry of the filesystem we ensure that we are
+ * indeed passed a dentry directly beneath the root dentry, that the inode
+ * associated with the root dentry is locked, and that it is a regular file we
+ * are asked to remove.
+ */
+static void unlink_binfmt_dentry(struct dentry *dentry)
 {
-	struct dentry *dentry;
+	struct dentry *parent = dentry->d_parent;
+	struct inode *inode, *parent_inode;
+
+	/* All entries are immediate descendants of the root dentry. */
+	if (WARN_ON_ONCE(dentry->d_sb->s_root != parent))
+		return;
 
+	/* We only expect to be called on regular files. */
+	inode = d_inode(dentry);
+	if (WARN_ON_ONCE(!S_ISREG(inode->i_mode)))
+		return;
+
+	/* The parent inode must be locked. */
+	parent_inode = d_inode(parent);
+	if (WARN_ON_ONCE(!inode_is_locked(parent_inode)))
+		return;
+
+	if (simple_positive(dentry)) {
+		dget(dentry);
+		simple_unlink(parent_inode, dentry);
+		d_delete(dentry);
+		dput(dentry);
+	}
+}
+
+/**
+ * remove_binfmt_handler - remove a binary type handler
+ * @misc: handle to binfmt_misc instance
+ * @e: binary type handler to remove
+ *
+ * Remove a binary type handler from the list of binary type handlers and
+ * remove its associated dentry. This is called from
+ * binfmt_{entry,status}_write(). In the future, we might want to think about
+ * adding a proper ->unlink() method to binfmt_misc instead of forcing caller's
+ * to use writes to files in order to delete binary type handlers. But it has
+ * worked for so long that it's not a pressing issue.
+ */
+static void remove_binfmt_handler(Node *e)
+{
 	write_lock(&entries_lock);
 	list_del_init(&e->list);
 	write_unlock(&entries_lock);
-
-	dentry = e->dentry;
-	drop_nlink(d_inode(dentry));
-	d_drop(dentry);
-	dput(dentry);
-	simple_release_fs(&bm_mnt, &entry_count);
+	unlink_binfmt_dentry(e->dentry);
 }
 
 /* /<entry> */
@@ -603,8 +710,8 @@
 static ssize_t bm_entry_write(struct file *file, const char __user *buffer,
 				size_t count, loff_t *ppos)
 {
-	struct dentry *root;
-	Node *e = file_inode(file)->i_private;
+	struct inode *inode = file_inode(file);
+	Node *e = inode->i_private;
 	int res = parse_command(buffer, count);
 
 	switch (res) {
@@ -618,13 +725,22 @@
 		break;
 	case 3:
 		/* Delete this handler. */
-		root = file_inode(file)->i_sb->s_root;
-		inode_lock(d_inode(root));
+		inode = d_inode(inode->i_sb->s_root);
+		inode_lock(inode);
 
+		/*
+		 * In order to add new element or remove elements from the list
+		 * via bm_{entry,register,status}_write() inode_lock() on the
+		 * root inode must be held.
+		 * The lock is exclusive ensuring that the list can't be
+		 * modified. Only load_misc_binary() can access but does so
+		 * read-only. So we only need to take the write lock when we
+		 * actually remove the entry from the list.
+		 */
 		if (!list_empty(&e->list))
-			kill_node(e);
+			remove_binfmt_handler(e);
 
-		inode_unlock(d_inode(root));
+		inode_unlock(inode);
 		break;
 	default:
 		return res;
@@ -683,13 +799,7 @@
 	if (!inode)
 		goto out2;
 
-	err = simple_pin_fs(&bm_fs_type, &bm_mnt, &entry_count);
-	if (err) {
-		iput(inode);
-		inode = NULL;
-		goto out2;
-	}
-
+	refcount_set(&e->users, 1);
 	e->dentry = dget(dentry);
 	inode->i_private = e;
 	inode->i_fop = &bm_entry_operations;
@@ -733,7 +843,8 @@
 		size_t count, loff_t *ppos)
 {
 	int res = parse_command(buffer, count);
-	struct dentry *root;
+	Node *e, *next;
+	struct inode *inode;
 
 	switch (res) {
 	case 1:
@@ -746,13 +857,22 @@
 		break;
 	case 3:
 		/* Delete all handlers. */
-		root = file_inode(file)->i_sb->s_root;
-		inode_lock(d_inode(root));
+		inode = d_inode(file_inode(file)->i_sb->s_root);
+		inode_lock(inode);
 
-		while (!list_empty(&entries))
-			kill_node(list_first_entry(&entries, Node, list));
+		/*
+		 * In order to add new element or remove elements from the list
+		 * via bm_{entry,register,status}_write() inode_lock() on the
+		 * root inode must be held.
+		 * The lock is exclusive ensuring that the list can't be
+		 * modified. Only load_misc_binary() can access but does so
+		 * read-only. So we only need to take the write lock when we
+		 * actually remove the entry from the list.
+		 */
+		list_for_each_entry_safe(e, next, &entries, list)
+			remove_binfmt_handler(e);
 
-		inode_unlock(d_inode(root));
+		inode_unlock(inode);
 		break;
 	default:
 		return res;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/async-thread.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/async-thread.c
@@ -234,6 +234,13 @@
 				  ordered_list);
 		if (!test_bit(WORK_DONE_BIT, &work->flags))
 			break;
+		/*
+		 * Orders all subsequent loads after reading WORK_DONE_BIT,
+		 * paired with the smp_mb__before_atomic in btrfs_work_helper
+		 * this guarantees that the ordered function will see all
+		 * updates from ordinary work function.
+		 */
+		smp_rmb();
 
 		/*
 		 * we are going to call the ordered done function, but
@@ -317,6 +324,13 @@
 	thresh_exec_hook(wq);
 	work->func(work);
 	if (need_order) {
+		/*
+		 * Ensures all memory accesses done in the work function are
+		 * ordered before setting the WORK_DONE_BIT. Ensuring the thread
+		 * which is going to executed the ordered work sees them.
+		 * Pairs with the smp_rmb in run_ordered_work.
+		 */
+		smp_mb__before_atomic();
 		set_bit(WORK_DONE_BIT, &work->flags);
 		run_ordered_work(wq, work);
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/backref.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/backref.c
@@ -138,6 +138,7 @@
 	u64 root_objectid;
 	u64 inum;
 	int share_count;
+	bool have_delayed_delete_refs;
 };
 
 static inline int extent_is_shared(struct share_check *sc)
@@ -288,8 +289,10 @@
 	struct prelim_ref *ref, *next_ref;
 
 	rbtree_postorder_for_each_entry_safe(ref, next_ref,
-					     &preftree->root.rb_root, rbnode)
+					     &preftree->root.rb_root, rbnode) {
+		free_inode_elem_list(ref->inode_list);
 		free_pref(ref);
+	}
 
 	preftree->root = RB_ROOT_CACHED;
 	preftree->count = 0;
@@ -430,6 +433,7 @@
 	u64 wanted_disk_byte = ref->wanted_disk_byte;
 	u64 count = 0;
 	u64 data_offset;
+	u8 type;
 
 	if (level != 0) {
 		eb = path->nodes[level];
@@ -484,6 +488,9 @@
 			continue;
 		}
 		fi = btrfs_item_ptr(eb, slot, struct btrfs_file_extent_item);
+		type = btrfs_file_extent_type(eb, fi);
+		if (type == BTRFS_FILE_EXTENT_INLINE)
+			goto next;
 		disk_byte = btrfs_file_extent_disk_bytenr(eb, fi);
 		data_offset = btrfs_file_extent_offset(eb, fi);
 
@@ -647,6 +654,18 @@
 	return (struct extent_inode_elem *)(uintptr_t)node->aux;
 }
 
+static void free_leaf_list(struct ulist *ulist)
+{
+	struct ulist_node *node;
+	struct ulist_iterator uiter;
+
+	ULIST_ITER_INIT(&uiter);
+	while ((node = ulist_next(ulist, &uiter)))
+		free_inode_elem_list(unode_aux_to_inode_list(node));
+
+	ulist_free(ulist);
+}
+
 /*
  * We maintain three separate rbtrees: one for direct refs, one for
  * indirect refs which have a key, and one for indirect refs which do not
@@ -761,7 +780,11 @@
 		cond_resched();
 	}
 out:
-	ulist_free(parents);
+	/*
+	 * We may have inode lists attached to refs in the parents ulist, so we
+	 * must free them before freeing the ulist and its refs.
+	 */
+	free_leaf_list(parents);
 	return ret;
 }
 
@@ -818,16 +841,11 @@
 			    struct preftrees *preftrees, struct share_check *sc)
 {
 	struct btrfs_delayed_ref_node *node;
-	struct btrfs_delayed_extent_op *extent_op = head->extent_op;
 	struct btrfs_key key;
-	struct btrfs_key tmp_op_key;
 	struct rb_node *n;
 	int count;
 	int ret = 0;
 
-	if (extent_op && extent_op->update_key)
-		btrfs_disk_key_to_cpu(&tmp_op_key, &extent_op->key);
-
 	spin_lock(&head->lock);
 	for (n = rb_first_cached(&head->ref_tree); n; n = rb_next(n)) {
 		node = rb_entry(n, struct btrfs_delayed_ref_node,
@@ -853,10 +871,16 @@
 		case BTRFS_TREE_BLOCK_REF_KEY: {
 			/* NORMAL INDIRECT METADATA backref */
 			struct btrfs_delayed_tree_ref *ref;
+			struct btrfs_key *key_ptr = NULL;
+
+			if (head->extent_op && head->extent_op->update_key) {
+				btrfs_disk_key_to_cpu(&key, &head->extent_op->key);
+				key_ptr = &key;
+			}
 
 			ref = btrfs_delayed_node_to_tree_ref(node);
 			ret = add_indirect_ref(fs_info, preftrees, ref->root,
-					       &tmp_op_key, ref->level + 1,
+					       key_ptr, ref->level + 1,
 					       node->bytenr, count, sc,
 					       GFP_ATOMIC);
 			break;
@@ -882,13 +906,22 @@
 			key.offset = ref->offset;
 
 			/*
-			 * Found a inum that doesn't match our known inum, we
-			 * know it's shared.
+			 * If we have a share check context and a reference for
+			 * another inode, we can't exit immediately. This is
+			 * because even if this is a BTRFS_ADD_DELAYED_REF
+			 * reference we may find next a BTRFS_DROP_DELAYED_REF
+			 * which cancels out this ADD reference.
+			 *
+			 * If this is a DROP reference and there was no previous
+			 * ADD reference, then we need to signal that when we
+			 * process references from the extent tree (through
+			 * add_inline_refs() and add_keyed_refs()), we should
+			 * not exit early if we find a reference for another
+			 * inode, because one of the delayed DROP references
+			 * may cancel that reference in the extent tree.
 			 */
-			if (sc && sc->inum && ref->objectid != sc->inum) {
-				ret = BACKREF_FOUND_SHARED;
-				goto out;
-			}
+			if (sc && count < 0)
+				sc->have_delayed_delete_refs = true;
 
 			ret = add_indirect_ref(fs_info, preftrees, ref->root,
 					       &key, 0, node->bytenr, count, sc,
@@ -918,7 +951,7 @@
 	}
 	if (!ret)
 		ret = extent_is_shared(sc);
-out:
+
 	spin_unlock(&head->lock);
 	return ret;
 }
@@ -1021,7 +1054,8 @@
 			key.type = BTRFS_EXTENT_DATA_KEY;
 			key.offset = btrfs_extent_data_ref_offset(leaf, dref);
 
-			if (sc && sc->inum && key.objectid != sc->inum) {
+			if (sc && sc->inum && key.objectid != sc->inum &&
+			    !sc->have_delayed_delete_refs) {
 				ret = BACKREF_FOUND_SHARED;
 				break;
 			}
@@ -1031,6 +1065,7 @@
 			ret = add_indirect_ref(fs_info, preftrees, root,
 					       &key, 0, bytenr, count,
 					       sc, GFP_NOFS);
+
 			break;
 		}
 		default:
@@ -1120,7 +1155,8 @@
 			key.type = BTRFS_EXTENT_DATA_KEY;
 			key.offset = btrfs_extent_data_ref_offset(leaf, dref);
 
-			if (sc && sc->inum && key.objectid != sc->inum) {
+			if (sc && sc->inum && key.objectid != sc->inum &&
+			    !sc->have_delayed_delete_refs) {
 				ret = BACKREF_FOUND_SHARED;
 				break;
 			}
@@ -1214,7 +1250,12 @@
 	ret = btrfs_search_slot(NULL, fs_info->extent_root, &key, path, 0, 0);
 	if (ret < 0)
 		goto out;
-	BUG_ON(ret == 0);
+	if (ret == 0) {
+		/* This shouldn't happen, indicates a bug or fs corruption. */
+		ASSERT(ret != 0);
+		ret = -EUCLEAN;
+		goto out;
+	}
 
 #ifdef CONFIG_BTRFS_FS_RUN_SANITY_TESTS
 	if (trans && likely(trans->type != __TRANS_DUMMY) &&
@@ -1352,6 +1393,12 @@
 				if (ret < 0)
 					goto out;
 				ref->inode_list = eie;
+				/*
+				 * We transferred the list ownership to the ref,
+				 * so set to NULL to avoid a double free in case
+				 * an error happens after this.
+				 */
+				eie = NULL;
 			}
 			ret = ulist_add_merge_ptr(refs, ref->parent,
 						  ref->inode_list,
@@ -1360,15 +1407,31 @@
 				goto out;
 			if (!ret && extent_item_pos) {
 				/*
-				 * we've recorded that parent, so we must extend
-				 * its inode list here
+				 * We've recorded that parent, so we must extend
+				 * its inode list here.
+				 *
+				 * However if there was corruption we may not
+				 * have found an eie, return an error in this
+				 * case.
 				 */
-				BUG_ON(!eie);
+				ASSERT(eie);
+				if (!eie) {
+					ret = -EUCLEAN;
+					goto out;
+				}
 				while (eie->next)
 					eie = eie->next;
 				eie->next = ref->inode_list;
 			}
 			eie = NULL;
+			/*
+			 * We have transferred the inode list ownership from
+			 * this ref to the ref we added to the 'refs' ulist.
+			 * So set this ref's inode list to NULL to avoid
+			 * use-after-free when our caller uses it or double
+			 * frees in case an error happens before we return.
+			 */
+			ref->inode_list = NULL;
 		}
 		cond_resched();
 	}
@@ -1385,24 +1448,6 @@
 	return ret;
 }
 
-static void free_leaf_list(struct ulist *blocks)
-{
-	struct ulist_node *node = NULL;
-	struct extent_inode_elem *eie;
-	struct ulist_iterator uiter;
-
-	ULIST_ITER_INIT(&uiter);
-	while ((node = ulist_next(blocks, &uiter))) {
-		if (!node->aux)
-			continue;
-		eie = unode_aux_to_inode_list(node);
-		free_inode_elem_list(eie);
-		node->aux = 0;
-	}
-
-	ulist_free(blocks);
-}
-
 /*
  * Finds all leafs with a reference to the specified combination of bytenr and
  * offset. key_list_head will point to a list of corresponding keys (caller must
@@ -1534,6 +1579,7 @@
 		.root_objectid = root->root_key.objectid,
 		.inum = inum,
 		.share_count = 0,
+		.have_delayed_delete_refs = false,
 	};
 
 	ulist_init(roots);
@@ -1568,6 +1614,7 @@
 			break;
 		bytenr = node->val;
 		shared.share_count = 0;
+		shared.have_delayed_delete_refs = false;
 		cond_resched();
 	}
 
@@ -2017,10 +2064,29 @@
 	return ret;
 }
 
+static int build_ino_list(u64 inum, u64 offset, u64 root, void *ctx)
+{
+	struct btrfs_data_container *inodes = ctx;
+	const size_t c = 3 * sizeof(u64);
+
+	if (inodes->bytes_left >= c) {
+		inodes->bytes_left -= c;
+		inodes->val[inodes->elem_cnt] = inum;
+		inodes->val[inodes->elem_cnt + 1] = offset;
+		inodes->val[inodes->elem_cnt + 2] = root;
+		inodes->elem_cnt += 3;
+	} else {
+		inodes->bytes_missing += c - inodes->bytes_left;
+		inodes->bytes_left = 0;
+		inodes->elem_missed += 3;
+	}
+
+	return 0;
+}
+
 int iterate_inodes_from_logical(u64 logical, struct btrfs_fs_info *fs_info,
 				struct btrfs_path *path,
-				iterate_extent_inodes_t *iterate, void *ctx,
-				bool ignore_offset)
+				void *ctx, bool ignore_offset)
 {
 	int ret;
 	u64 extent_item_pos;
@@ -2038,7 +2104,7 @@
 	extent_item_pos = logical - found_key.objectid;
 	ret = iterate_extent_inodes(fs_info, found_key.objectid,
 					extent_item_pos, search_commit_root,
-					iterate, ctx, ignore_offset);
+					build_ino_list, ctx, ignore_offset);
 
 	return ret;
 }
@@ -2249,20 +2315,14 @@
 	size_t alloc_bytes;
 
 	alloc_bytes = max_t(size_t, total_bytes, sizeof(*data));
-	data = kvmalloc(alloc_bytes, GFP_KERNEL);
+	data = kvzalloc(alloc_bytes, GFP_KERNEL);
 	if (!data)
 		return ERR_PTR(-ENOMEM);
 
-	if (total_bytes >= sizeof(*data)) {
+	if (total_bytes >= sizeof(*data))
 		data->bytes_left = total_bytes - sizeof(*data);
-		data->bytes_missing = 0;
-	} else {
+	else
 		data->bytes_missing = sizeof(*data) - total_bytes;
-		data->bytes_left = 0;
-	}
-
-	data->elem_cnt = 0;
-	data->elem_missed = 0;
 
 	return data;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/backref.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/backref.h
@@ -35,8 +35,7 @@
 				bool ignore_offset);
 
 int iterate_inodes_from_logical(u64 logical, struct btrfs_fs_info *fs_info,
-				struct btrfs_path *path,
-				iterate_extent_inodes_t *iterate, void *ctx,
+				struct btrfs_path *path, void *ctx,
 				bool ignore_offset);
 
 int paths_from_inode(u64 inum, struct inode_fs_paths *ipath);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/block-group.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/block-group.c
@@ -78,14 +78,21 @@
 	}
 	allowed &= flags;
 
-	if (allowed & BTRFS_BLOCK_GROUP_RAID6)
+	/* Select the highest-redundancy RAID level. */
+	if (allowed & BTRFS_BLOCK_GROUP_RAID1C4)
+		allowed = BTRFS_BLOCK_GROUP_RAID1C4;
+	else if (allowed & BTRFS_BLOCK_GROUP_RAID6)
 		allowed = BTRFS_BLOCK_GROUP_RAID6;
+	else if (allowed & BTRFS_BLOCK_GROUP_RAID1C3)
+		allowed = BTRFS_BLOCK_GROUP_RAID1C3;
 	else if (allowed & BTRFS_BLOCK_GROUP_RAID5)
 		allowed = BTRFS_BLOCK_GROUP_RAID5;
 	else if (allowed & BTRFS_BLOCK_GROUP_RAID10)
 		allowed = BTRFS_BLOCK_GROUP_RAID10;
 	else if (allowed & BTRFS_BLOCK_GROUP_RAID1)
 		allowed = BTRFS_BLOCK_GROUP_RAID1;
+	else if (allowed & BTRFS_BLOCK_GROUP_DUP)
+		allowed = BTRFS_BLOCK_GROUP_DUP;
 	else if (allowed & BTRFS_BLOCK_GROUP_RAID0)
 		allowed = BTRFS_BLOCK_GROUP_RAID0;
 
@@ -123,7 +130,16 @@
 {
 	if (refcount_dec_and_test(&cache->refs)) {
 		WARN_ON(cache->pinned > 0);
-		WARN_ON(cache->reserved > 0);
+		/*
+		 * If there was a failure to cleanup a log tree, very likely due
+		 * to an IO failure on a writeback attempt of one or more of its
+		 * extent buffers, we could not do proper (and cheap) unaccounting
+		 * of their reserved space, so don't warn on reserved > 0 in that
+		 * case.
+		 */
+		if (!(cache->flags & BTRFS_BLOCK_GROUP_METADATA) ||
+		    !BTRFS_FS_LOG_CLEANUP_ERROR(cache->fs_info))
+			WARN_ON(cache->reserved > 0);
 
 		/*
 		 * A block_group shouldn't be on the discard_list anymore.
@@ -409,39 +425,26 @@
 	btrfs_put_caching_control(caching_ctl);
 }
 
-int btrfs_wait_block_group_cache_done(struct btrfs_block_group *cache)
+static int btrfs_caching_ctl_wait_done(struct btrfs_block_group *cache,
+				       struct btrfs_caching_control *caching_ctl)
+{
+	wait_event(caching_ctl->wait, btrfs_block_group_done(cache));
+	return cache->cached == BTRFS_CACHE_ERROR ? -EIO : 0;
+}
+
+static int btrfs_wait_block_group_cache_done(struct btrfs_block_group *cache)
 {
 	struct btrfs_caching_control *caching_ctl;
-	int ret = 0;
+	int ret;
 
 	caching_ctl = btrfs_get_caching_control(cache);
 	if (!caching_ctl)
 		return (cache->cached == BTRFS_CACHE_ERROR) ? -EIO : 0;
-
-	wait_event(caching_ctl->wait, btrfs_block_group_done(cache));
-	if (cache->cached == BTRFS_CACHE_ERROR)
-		ret = -EIO;
+	ret = btrfs_caching_ctl_wait_done(cache, caching_ctl);
 	btrfs_put_caching_control(caching_ctl);
 	return ret;
 }
 
-static bool space_cache_v1_done(struct btrfs_block_group *cache)
-{
-	bool ret;
-
-	spin_lock(&cache->lock);
-	ret = cache->cached != BTRFS_CACHE_FAST;
-	spin_unlock(&cache->lock);
-
-	return ret;
-}
-
-void btrfs_wait_space_cache_v1_finished(struct btrfs_block_group *cache,
-				struct btrfs_caching_control *caching_ctl)
-{
-	wait_event(caching_ctl->wait, space_cache_v1_done(cache));
-}
-
 #ifdef CONFIG_BTRFS_DEBUG
 static void fragment_free_space(struct btrfs_block_group *block_group)
 {
@@ -718,9 +721,8 @@
 	btrfs_put_block_group(block_group);
 }
 
-int btrfs_cache_block_group(struct btrfs_block_group *cache, int load_cache_only)
+int btrfs_cache_block_group(struct btrfs_block_group *cache, bool wait)
 {
-	DEFINE_WAIT(wait);
 	struct btrfs_fs_info *fs_info = cache->fs_info;
 	struct btrfs_caching_control *caching_ctl = NULL;
 	int ret = 0;
@@ -753,10 +755,7 @@
 	}
 	WARN_ON(cache->caching_ctl);
 	cache->caching_ctl = caching_ctl;
-	if (btrfs_test_opt(fs_info, SPACE_CACHE))
-		cache->cached = BTRFS_CACHE_FAST;
-	else
-		cache->cached = BTRFS_CACHE_STARTED;
+	cache->cached = BTRFS_CACHE_STARTED;
 	cache->has_caching_ctl = 1;
 	spin_unlock(&cache->lock);
 
@@ -769,8 +768,8 @@
 
 	btrfs_queue_work(fs_info->caching_workers, &caching_ctl->work);
 out:
-	if (load_cache_only && caching_ctl)
-		btrfs_wait_space_cache_v1_finished(cache, caching_ctl);
+	if (wait && caching_ctl)
+		ret = btrfs_caching_ctl_wait_done(cache, caching_ctl);
 	if (caching_ctl)
 		btrfs_put_caching_control(caching_ctl);
 
@@ -902,6 +901,7 @@
 	spin_unlock(&cluster->refill_lock);
 
 	btrfs_clear_treelog_bg(block_group);
+	btrfs_clear_data_reloc_bg(block_group);
 
 	path = btrfs_alloc_path();
 	if (!path) {
@@ -1475,11 +1475,14 @@
 {
 	struct btrfs_fs_info *fs_info = bg->fs_info;
 
+	trace_btrfs_add_unused_block_group(bg);
 	spin_lock(&fs_info->unused_bgs_lock);
 	if (list_empty(&bg->bg_list)) {
 		btrfs_get_block_group(bg);
-		trace_btrfs_add_unused_block_group(bg);
 		list_add_tail(&bg->bg_list, &fs_info->unused_bgs);
+	} else {
+		/* Pull out the block group from the reclaim_bgs list. */
+		list_move_tail(&bg->bg_list, &fs_info->unused_bgs);
 	}
 	spin_unlock(&fs_info->unused_bgs_lock);
 }
@@ -1490,13 +1493,17 @@
 		container_of(work, struct btrfs_fs_info, reclaim_bgs_work);
 	struct btrfs_block_group *bg;
 	struct btrfs_space_info *space_info;
-	LIST_HEAD(again_list);
+	LIST_HEAD(retry_list);
 
 	if (!test_bit(BTRFS_FS_OPEN, &fs_info->flags))
 		return;
 
-	if (!btrfs_exclop_start(fs_info, BTRFS_EXCLOP_BALANCE))
+	sb_start_write(fs_info->sb);
+
+	if (!btrfs_exclop_start(fs_info, BTRFS_EXCLOP_BALANCE)) {
+		sb_end_write(fs_info->sb);
 		return;
+	}
 
 	/*
 	 * Long running balances can keep us blocked here for eternity, so
@@ -1504,6 +1511,7 @@
 	 */
 	if (!mutex_trylock(&fs_info->reclaim_bgs_lock)) {
 		btrfs_exclop_finish(fs_info);
+		sb_end_write(fs_info->sb);
 		return;
 	}
 
@@ -1537,8 +1545,15 @@
 		}
 		spin_unlock(&bg->lock);
 
-		/* Get out fast, in case we're unmounting the filesystem */
-		if (btrfs_fs_closing(fs_info)) {
+		/*
+		 * Get out fast, in case we're read-only or unmounting the
+		 * filesystem. It is OK to drop block groups from the list even
+		 * for the read-only case. As we did sb_start_write(),
+		 * "mount -o remount,ro" won't happen and read-only filesystem
+		 * means it is forced read-only due to a fatal error. So, it
+		 * never gets back to read-write to let us reclaim again.
+		 */
+		if (btrfs_need_cleaner_sleep(fs_info)) {
 			up_write(&space_info->groups_sem);
 			goto next;
 		}
@@ -1557,25 +1572,56 @@
 
 		btrfs_info(fs_info,
 			"reclaiming chunk %llu with %llu%% used %llu%% unusable",
-				bg->start, div_u64(bg->used * 100, bg->length),
+				bg->start,
+				div64_u64(bg->used * 100, bg->length),
 				div64_u64(zone_unusable * 100, bg->length));
 		trace_btrfs_reclaim_block_group(bg);
 		ret = btrfs_relocate_chunk(fs_info, bg->start);
-		if (ret && ret != -EAGAIN)
+		if (ret) {
+			btrfs_dec_block_group_ro(bg);
 			btrfs_err(fs_info, "error relocating chunk %llu",
 				  bg->start);
+		}
 
 next:
+		if (ret) {
+			/* Refcount held by the reclaim_bgs list after splice. */
+			spin_lock(&fs_info->unused_bgs_lock);
+			/*
+			 * This block group might be added to the unused list
+			 * during the above process. Move it back to the
+			 * reclaim list otherwise.
+			 */
+			if (list_empty(&bg->bg_list)) {
+				btrfs_get_block_group(bg);
+				list_add_tail(&bg->bg_list, &retry_list);
+			}
+			spin_unlock(&fs_info->unused_bgs_lock);
+		}
+		btrfs_put_block_group(bg);
+
+		mutex_unlock(&fs_info->reclaim_bgs_lock);
+		/*
+		 * Reclaiming all the block groups in the list can take really
+		 * long.  Prioritize cleaning up unused block groups.
+		 */
+		btrfs_delete_unused_bgs(fs_info);
+		/*
+		 * If we are interrupted by a balance, we can just bail out. The
+		 * cleaner thread restart again if necessary.
+		 */
+		if (!mutex_trylock(&fs_info->reclaim_bgs_lock))
+			goto end;
 		spin_lock(&fs_info->unused_bgs_lock);
-		if (ret == -EAGAIN && list_empty(&bg->bg_list))
-			list_add_tail(&bg->bg_list, &again_list);
-		else
-			btrfs_put_block_group(bg);
 	}
-	list_splice_tail(&again_list, &fs_info->reclaim_bgs);
 	spin_unlock(&fs_info->unused_bgs_lock);
 	mutex_unlock(&fs_info->reclaim_bgs_lock);
+end:
+	spin_lock(&fs_info->unused_bgs_lock);
+	list_splice_tail(&retry_list, &fs_info->reclaim_bgs);
+	spin_unlock(&fs_info->unused_bgs_lock);
 	btrfs_exclop_finish(fs_info);
+	sb_end_write(fs_info->sb);
 }
 
 void btrfs_reclaim_bgs(struct btrfs_fs_info *fs_info)
@@ -1828,6 +1874,7 @@
 
 		/* Shouldn't have super stripes in sequential zones */
 		if (zoned && nr) {
+			kfree(logical);
 			btrfs_err(fs_info,
 			"zoned: block group %llu must not contain super block",
 				  cache->start);
@@ -2143,7 +2190,16 @@
 	int need_clear = 0;
 	u64 cache_gen;
 
-	if (!info->extent_root)
+	/*
+	 * Either no extent root (with ibadroots rescue option) or we have
+	 * unsupported RO options. The fs can never be mounted read-write, so no
+	 * need to waste time searching block group items.
+	 *
+	 * This also allows new extent tree related changes to be RO compat,
+	 * no need for a full incompat flag.
+	 */
+	if (!info->extent_root || (btrfs_super_compat_ro_flags(info->super_copy) &
+		      ~BTRFS_FEATURE_COMPAT_RO_SUPP))
 		return fill_dummy_bgs(info);
 
 	key.objectid = 0;
@@ -2510,6 +2566,19 @@
 	int ret;
 	bool dirty_bg_running;
 
+	/*
+	 * This can only happen when we are doing read-only scrub on read-only
+	 * mount.
+	 * In that case we should not start a new transaction on read-only fs.
+	 * Thus here we skip all chunk allocations.
+	 */
+	if (sb_rdonly(fs_info->sb)) {
+		mutex_lock(&fs_info->ro_block_group_mutex);
+		ret = inc_block_group_ro(cache, 0);
+		mutex_unlock(&fs_info->ro_block_group_mutex);
+		return ret;
+	}
+
 	do {
 		trans = btrfs_join_transaction(fs_info->extent_root);
 		if (IS_ERR(trans))
@@ -2557,10 +2626,20 @@
 	}
 
 	ret = inc_block_group_ro(cache, 0);
-	if (!do_chunk_alloc || ret == -ETXTBSY)
-		goto unlock_out;
 	if (!ret)
 		goto out;
+	if (ret == -ETXTBSY)
+		goto unlock_out;
+
+	/*
+	 * Skip chunk alloction if the bg is SYSTEM, this is to avoid system
+	 * chunk allocation storm to exhaust the system chunk array.  Otherwise
+	 * we still want to try our best to mark the block group read-only.
+	 */
+	if (!do_chunk_alloc && ret == -ENOSPC &&
+	    (cache->flags & BTRFS_BLOCK_GROUP_SYSTEM))
+		goto unlock_out;
+
 	alloc_flags = btrfs_get_alloc_profile(fs_info, cache->space_info->flags);
 	ret = btrfs_chunk_alloc(trans, alloc_flags, CHUNK_ALLOC_FORCE);
 	if (ret < 0)
@@ -2858,7 +2937,6 @@
 	struct btrfs_path *path = NULL;
 	LIST_HEAD(dirty);
 	struct list_head *io = &cur_trans->io_bgs;
-	int num_started = 0;
 	int loops = 0;
 
 	spin_lock(&cur_trans->dirty_bgs_lock);
@@ -2924,7 +3002,6 @@
 			cache->io_ctl.inode = NULL;
 			ret = btrfs_write_out_cache(trans, cache, path);
 			if (ret == 0 && cache->io_ctl.inode) {
-				num_started++;
 				should_put = 0;
 
 				/*
@@ -3025,7 +3102,6 @@
 	int should_put;
 	struct btrfs_path *path;
 	struct list_head *io = &cur_trans->io_bgs;
-	int num_started = 0;
 
 	path = btrfs_alloc_path();
 	if (!path)
@@ -3083,7 +3159,6 @@
 			cache->io_ctl.inode = NULL;
 			ret = btrfs_write_out_cache(trans, cache, path);
 			if (ret == 0 && cache->io_ctl.inode) {
-				num_started++;
 				should_put = 0;
 				list_add_tail(&cache->io_list, io);
 			} else {
@@ -3178,7 +3253,7 @@
 		 * space back to the block group, otherwise we will leak space.
 		 */
 		if (!alloc && !btrfs_block_group_done(cache))
-			btrfs_cache_block_group(cache, 1);
+			btrfs_cache_block_group(cache, true);
 
 		byte_in_group = bytenr - cache->start;
 		WARN_ON(byte_in_group > cache->length);
@@ -3311,6 +3386,8 @@
 	spin_lock(&cache->lock);
 	if (cache->ro)
 		space_info->bytes_readonly += num_bytes;
+	else if (btrfs_is_zoned(cache->fs_info))
+		space_info->bytes_zone_unusable += num_bytes;
 	cache->reserved -= num_bytes;
 	space_info->bytes_reserved -= num_bytes;
 	space_info->max_extent_size = 0;
@@ -3380,31 +3457,12 @@
 	 */
 	check_system_chunk(trans, flags);
 
-	bg = btrfs_alloc_chunk(trans, flags);
+	bg = btrfs_create_chunk(trans, flags);
 	if (IS_ERR(bg)) {
 		ret = PTR_ERR(bg);
 		goto out;
 	}
 
-	/*
-	 * If this is a system chunk allocation then stop right here and do not
-	 * add the chunk item to the chunk btree. This is to prevent a deadlock
-	 * because this system chunk allocation can be triggered while COWing
-	 * some extent buffer of the chunk btree and while holding a lock on a
-	 * parent extent buffer, in which case attempting to insert the chunk
-	 * item (or update the device item) would result in a deadlock on that
-	 * parent extent buffer. In this case defer the chunk btree updates to
-	 * the second phase of chunk allocation and keep our reservation until
-	 * the second phase completes.
-	 *
-	 * This is a rare case and can only be triggered by the very few cases
-	 * we have where we need to touch the chunk btree outside chunk allocation
-	 * and chunk removal. These cases are basically adding a device, removing
-	 * a device or resizing a device.
-	 */
-	if (flags & BTRFS_BLOCK_GROUP_SYSTEM)
-		return 0;
-
 	ret = btrfs_chunk_alloc_add_chunk_item(trans, bg);
 	/*
 	 * Normally we are not expected to fail with -ENOSPC here, since we have
@@ -3441,7 +3499,7 @@
 		const u64 sys_flags = btrfs_system_alloc_profile(trans->fs_info);
 		struct btrfs_block_group *sys_bg;
 
-		sys_bg = btrfs_alloc_chunk(trans, sys_flags);
+		sys_bg = btrfs_create_chunk(trans, sys_flags);
 		if (IS_ERR(sys_bg)) {
 			ret = PTR_ERR(sys_bg);
 			btrfs_abort_transaction(trans, ret);
@@ -3537,14 +3595,14 @@
  * This has happened before and commit eafa4fd0ad0607 ("btrfs: fix exhaustion of
  * the system chunk array due to concurrent allocations") provides more details.
  *
- * For allocation of system chunks, we defer the updates and insertions into the
- * chunk btree to phase 2. This is to prevent deadlocks on extent buffers because
- * if the chunk allocation is triggered while COWing an extent buffer of the
- * chunk btree, we are holding a lock on the parent of that extent buffer and
- * doing the chunk btree updates and insertions can require locking that parent.
- * This is for the very few and rare cases where we update the chunk btree that
- * are not chunk allocation or chunk removal: adding a device, removing a device
- * or resizing a device.
+ * Allocation of system chunks does not happen through this function. A task that
+ * needs to update the chunk btree (the only btree that uses system chunks), must
+ * preallocate chunk space by calling either check_system_chunk() or
+ * btrfs_reserve_chunk_metadata() - the former is used when allocating a data or
+ * metadata chunk or when removing a chunk, while the later is used before doing
+ * a modification to the chunk btree - use cases for the later are adding,
+ * removing and resizing a device as well as relocation of a system chunk.
+ * See the comment below for more details.
  *
  * The reservation of system space, done through check_system_chunk(), as well
  * as all the updates and insertions into the chunk btree must be done while
@@ -3581,11 +3639,27 @@
 	if (trans->allocating_chunk)
 		return -ENOSPC;
 	/*
-	 * If we are removing a chunk, don't re-enter or we would deadlock.
-	 * System space reservation and system chunk allocation is done by the
-	 * chunk remove operation (btrfs_remove_chunk()).
+	 * Allocation of system chunks can not happen through this path, as we
+	 * could end up in a deadlock if we are allocating a data or metadata
+	 * chunk and there is another task modifying the chunk btree.
+	 *
+	 * This is because while we are holding the chunk mutex, we will attempt
+	 * to add the new chunk item to the chunk btree or update an existing
+	 * device item in the chunk btree, while the other task that is modifying
+	 * the chunk btree is attempting to COW an extent buffer while holding a
+	 * lock on it and on its parent - if the COW operation triggers a system
+	 * chunk allocation, then we can deadlock because we are holding the
+	 * chunk mutex and we may need to access that extent buffer or its parent
+	 * in order to add the chunk item or update a device item.
+	 *
+	 * Tasks that want to modify the chunk tree should reserve system space
+	 * before updating the chunk btree, by calling either
+	 * btrfs_reserve_chunk_metadata() or check_system_chunk().
+	 * It's possible that after a task reserves the space, it still ends up
+	 * here - this happens in the cases described above at do_chunk_alloc().
+	 * The task will have to either retry or fail.
 	 */
-	if (trans->removing_chunk)
+	if (flags & BTRFS_BLOCK_GROUP_SYSTEM)
 		return -ENOSPC;
 
 	space_info = btrfs_find_space_info(fs_info, flags);
@@ -3615,6 +3689,7 @@
 			 * attempt.
 			 */
 			wait_for_alloc = true;
+			force = CHUNK_ALLOC_NO_FORCE;
 			spin_unlock(&space_info->lock);
 			mutex_lock(&fs_info->chunk_mutex);
 			mutex_unlock(&fs_info->chunk_mutex);
@@ -3684,17 +3759,14 @@
 	return num_dev;
 }
 
-/*
- * Reserve space in the system space for allocating or removing a chunk
- */
-void check_system_chunk(struct btrfs_trans_handle *trans, u64 type)
+static void reserve_chunk_space(struct btrfs_trans_handle *trans,
+				u64 bytes,
+				u64 type)
 {
 	struct btrfs_fs_info *fs_info = trans->fs_info;
 	struct btrfs_space_info *info;
 	u64 left;
-	u64 thresh;
 	int ret = 0;
-	u64 num_devs;
 
 	/*
 	 * Needed because we can end up allocating a system chunk and for an
@@ -3707,19 +3779,13 @@
 	left = info->total_bytes - btrfs_space_info_used(info, true);
 	spin_unlock(&info->lock);
 
-	num_devs = get_profile_num_devs(fs_info, type);
-
-	/* num_devs device items to update and 1 chunk item to add or remove */
-	thresh = btrfs_calc_metadata_size(fs_info, num_devs) +
-		btrfs_calc_insert_metadata_size(fs_info, 1);
-
-	if (left < thresh && btrfs_test_opt(fs_info, ENOSPC_DEBUG)) {
+	if (left < bytes && btrfs_test_opt(fs_info, ENOSPC_DEBUG)) {
 		btrfs_info(fs_info, "left=%llu, need=%llu, flags=%llu",
-			   left, thresh, type);
+			   left, bytes, type);
 		btrfs_dump_space_info(fs_info, info, 0, 0);
 	}
 
-	if (left < thresh) {
+	if (left < bytes) {
 		u64 flags = btrfs_system_alloc_profile(fs_info);
 		struct btrfs_block_group *bg;
 
@@ -3728,21 +3794,20 @@
 		 * needing it, as we might not need to COW all nodes/leafs from
 		 * the paths we visit in the chunk tree (they were already COWed
 		 * or created in the current transaction for example).
-		 *
-		 * Also, if our caller is allocating a system chunk, do not
-		 * attempt to insert the chunk item in the chunk btree, as we
-		 * could deadlock on an extent buffer since our caller may be
-		 * COWing an extent buffer from the chunk btree.
 		 */
-		bg = btrfs_alloc_chunk(trans, flags);
+		bg = btrfs_create_chunk(trans, flags);
 		if (IS_ERR(bg)) {
 			ret = PTR_ERR(bg);
-		} else if (!(type & BTRFS_BLOCK_GROUP_SYSTEM)) {
+		} else {
 			/*
 			 * If we fail to add the chunk item here, we end up
 			 * trying again at phase 2 of chunk allocation, at
 			 * btrfs_create_pending_block_groups(). So ignore
-			 * any error here.
+			 * any error here. An ENOSPC here could happen, due to
+			 * the cases described at do_chunk_alloc() - the system
+			 * block group we just created was just turned into RO
+			 * mode by a scrub for example, or a running discard
+			 * temporarily removed its free space entries, etc.
 			 */
 			btrfs_chunk_alloc_add_chunk_item(trans, bg);
 		}
@@ -3751,12 +3816,61 @@
 	if (!ret) {
 		ret = btrfs_block_rsv_add(fs_info->chunk_root,
 					  &fs_info->chunk_block_rsv,
-					  thresh, BTRFS_RESERVE_NO_FLUSH);
+					  bytes, BTRFS_RESERVE_NO_FLUSH);
 		if (!ret)
-			trans->chunk_bytes_reserved += thresh;
+			trans->chunk_bytes_reserved += bytes;
 	}
 }
 
+/*
+ * Reserve space in the system space for allocating or removing a chunk.
+ * The caller must be holding fs_info->chunk_mutex.
+ */
+void check_system_chunk(struct btrfs_trans_handle *trans, u64 type)
+{
+	struct btrfs_fs_info *fs_info = trans->fs_info;
+	const u64 num_devs = get_profile_num_devs(fs_info, type);
+	u64 bytes;
+
+	/* num_devs device items to update and 1 chunk item to add or remove. */
+	bytes = btrfs_calc_metadata_size(fs_info, num_devs) +
+		btrfs_calc_insert_metadata_size(fs_info, 1);
+
+	reserve_chunk_space(trans, bytes, type);
+}
+
+/*
+ * Reserve space in the system space, if needed, for doing a modification to the
+ * chunk btree.
+ *
+ * @trans:		A transaction handle.
+ * @is_item_insertion:	Indicate if the modification is for inserting a new item
+ *			in the chunk btree or if it's for the deletion or update
+ *			of an existing item.
+ *
+ * This is used in a context where we need to update the chunk btree outside
+ * block group allocation and removal, to avoid a deadlock with a concurrent
+ * task that is allocating a metadata or data block group and therefore needs to
+ * update the chunk btree while holding the chunk mutex. After the update to the
+ * chunk btree is done, btrfs_trans_release_chunk_metadata() should be called.
+ *
+ */
+void btrfs_reserve_chunk_metadata(struct btrfs_trans_handle *trans,
+				  bool is_item_insertion)
+{
+	struct btrfs_fs_info *fs_info = trans->fs_info;
+	u64 bytes;
+
+	if (is_item_insertion)
+		bytes = btrfs_calc_insert_metadata_size(fs_info, 1);
+	else
+		bytes = btrfs_calc_metadata_size(fs_info, 1);
+
+	mutex_lock(&fs_info->chunk_mutex);
+	reserve_chunk_space(trans, bytes, BTRFS_BLOCK_GROUP_SYSTEM);
+	mutex_unlock(&fs_info->chunk_mutex);
+}
+
 void btrfs_put_block_group_cache(struct btrfs_fs_info *info)
 {
 	struct btrfs_block_group *block_group;
@@ -3879,9 +3993,22 @@
 		 * important and indicates a real bug if this happens.
 		 */
 		if (WARN_ON(space_info->bytes_pinned > 0 ||
-			    space_info->bytes_reserved > 0 ||
 			    space_info->bytes_may_use > 0))
 			btrfs_dump_space_info(info, space_info, 0, 0);
+
+		/*
+		 * If there was a failure to cleanup a log tree, very likely due
+		 * to an IO failure on a writeback attempt of one or more of its
+		 * extent buffers, we could not do proper (and cheap) unaccounting
+		 * of their reserved space, so don't warn on bytes_reserved > 0 in
+		 * that case.
+		 */
+		if (!(space_info->flags & BTRFS_BLOCK_GROUP_METADATA) ||
+		    !BTRFS_FS_LOG_CLEANUP_ERROR(info)) {
+			if (WARN_ON(space_info->bytes_reserved > 0))
+				btrfs_dump_space_info(info, space_info, 0, 0);
+		}
+
 		WARN_ON(space_info->reclaim_size > 0);
 		list_del(&space_info->list);
 		btrfs_sysfs_remove_space_info(space_info);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/block-group.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/block-group.h
@@ -98,6 +98,7 @@
 	unsigned int to_copy:1;
 	unsigned int relocating_repair:1;
 	unsigned int chunk_item_inserted:1;
+	unsigned int zoned_data_reloc_ongoing:1;
 
 	int disk_cache_state;
 
@@ -250,9 +251,7 @@
 void btrfs_wait_nocow_writers(struct btrfs_block_group *bg);
 void btrfs_wait_block_group_cache_progress(struct btrfs_block_group *cache,
 				           u64 num_bytes);
-int btrfs_wait_block_group_cache_done(struct btrfs_block_group *cache);
-int btrfs_cache_block_group(struct btrfs_block_group *cache,
-			    int load_cache_only);
+int btrfs_cache_block_group(struct btrfs_block_group *cache, bool wait);
 void btrfs_put_caching_control(struct btrfs_caching_control *ctl);
 struct btrfs_caching_control *btrfs_get_caching_control(
 		struct btrfs_block_group *cache);
@@ -289,6 +288,8 @@
 		      enum btrfs_chunk_alloc_enum force);
 int btrfs_force_chunk_alloc(struct btrfs_trans_handle *trans, u64 type);
 void check_system_chunk(struct btrfs_trans_handle *trans, const u64 type);
+void btrfs_reserve_chunk_metadata(struct btrfs_trans_handle *trans,
+				  bool is_item_insertion);
 u64 btrfs_get_alloc_profile(struct btrfs_fs_info *fs_info, u64 orig_flags);
 void btrfs_put_block_group_cache(struct btrfs_fs_info *info);
 int btrfs_free_block_groups(struct btrfs_fs_info *info);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/block-rsv.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/block-rsv.c
@@ -121,7 +121,8 @@
 	} else {
 		num_bytes = 0;
 	}
-	if (block_rsv->qgroup_rsv_reserved >= block_rsv->qgroup_rsv_size) {
+	if (qgroup_to_release_ret &&
+	    block_rsv->qgroup_rsv_reserved >= block_rsv->qgroup_rsv_size) {
 		qgroup_to_release = block_rsv->qgroup_rsv_reserved -
 				    block_rsv->qgroup_rsv_size;
 		block_rsv->qgroup_rsv_reserved = block_rsv->qgroup_rsv_size;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/btrfs_inode.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/btrfs_inode.h
@@ -14,6 +14,13 @@
 #include "delayed-inode.h"
 
 /*
+ * Since we search a directory based on f_pos (struct dir_context::pos) we have
+ * to start at 2 since '.' and '..' have f_pos of 0 and 1 respectively, so
+ * everybody else has to start at 2 (see btrfs_real_readdir() and dir_emit_dots()).
+ */
+#define BTRFS_DIR_START_INDEX 2
+
+/*
  * ordered_data_close is set by truncate when a file that used
  * to have good data has been truncated to zero.  When it is set
  * the btrfs file release call will add this inode to the
@@ -164,8 +171,9 @@
 	u64 disk_i_size;
 
 	/*
-	 * if this is a directory then index_cnt is the counter for the index
-	 * number for new files that are created
+	 * If this is a directory then index_cnt is the counter for the index
+	 * number for new files that are created. For an empty directory, this
+	 * must be initialized to BTRFS_DIR_START_INDEX.
 	 */
 	u64 index_cnt;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/check-integrity.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/check-integrity.c
@@ -1455,7 +1455,7 @@
 	struct btrfs_fs_info *fs_info = state->fs_info;
 	int ret;
 	u64 length;
-	struct btrfs_bio *multi = NULL;
+	struct btrfs_io_context *multi = NULL;
 	struct btrfs_device *device;
 
 	length = len;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/compression.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/compression.c
@@ -550,7 +550,6 @@
 	u64 isize = i_size_read(inode);
 	int ret;
 	struct page *page;
-	unsigned long nr_pages = 0;
 	struct extent_map *em;
 	struct address_space *mapping = inode->i_mapping;
 	struct extent_map_tree *em_tree;
@@ -646,7 +645,6 @@
 				   PAGE_SIZE, 0);
 
 		if (ret == PAGE_SIZE) {
-			nr_pages++;
 			put_page(page);
 		} else {
 			unlock_extent(tree, last_offset, end);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/ctree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/ctree.c
@@ -76,6 +76,8 @@
 
 struct btrfs_path *btrfs_alloc_path(void)
 {
+	might_sleep();
+
 	return kmem_cache_zalloc(btrfs_path_cachep, GFP_NOFS);
 }
 
@@ -306,8 +308,16 @@
 	}
 
 	owner = btrfs_header_owner(buf);
-	BUG_ON(owner == BTRFS_TREE_RELOC_OBJECTID &&
-	       !(flags & BTRFS_BLOCK_FLAG_FULL_BACKREF));
+	if (unlikely(owner == BTRFS_TREE_RELOC_OBJECTID &&
+		     !(flags & BTRFS_BLOCK_FLAG_FULL_BACKREF))) {
+		btrfs_crit(fs_info,
+"found tree block at bytenr %llu level %d root %llu refs %llu flags %llx without full backref flag set",
+			   buf->start, btrfs_header_level(buf),
+			   btrfs_root_id(root), refs, flags);
+		ret = -EUCLEAN;
+		btrfs_abort_transaction(trans, ret);
+		return ret;
+	}
 
 	if (refs > 1) {
 		if ((owner == root->root_key.objectid ||
@@ -376,13 +386,13 @@
  * bytes the allocator should try to find free next to the block it returns.
  * This is just a hint and may be ignored by the allocator.
  */
-static noinline int __btrfs_cow_block(struct btrfs_trans_handle *trans,
-			     struct btrfs_root *root,
-			     struct extent_buffer *buf,
-			     struct extent_buffer *parent, int parent_slot,
-			     struct extent_buffer **cow_ret,
-			     u64 search_start, u64 empty_size,
-			     enum btrfs_lock_nesting nest)
+int btrfs_force_cow_block(struct btrfs_trans_handle *trans,
+			  struct btrfs_root *root,
+			  struct extent_buffer *buf,
+			  struct extent_buffer *parent, int parent_slot,
+			  struct extent_buffer **cow_ret,
+			  u64 search_start, u64 empty_size,
+			  enum btrfs_lock_nesting nest)
 {
 	struct btrfs_fs_info *fs_info = root->fs_info;
 	struct btrfs_disk_key disk_key;
@@ -457,13 +467,18 @@
 		    btrfs_header_backref_rev(buf) < BTRFS_MIXED_BACKREF_REV)
 			parent_start = buf->start;
 
-		atomic_inc(&cow->refs);
 		ret = btrfs_tree_mod_log_insert_root(root->node, cow, true);
-		BUG_ON(ret < 0);
+		if (ret < 0) {
+			btrfs_tree_unlock(cow);
+			free_extent_buffer(cow);
+			btrfs_abort_transaction(trans, ret);
+			return ret;
+		}
+		atomic_inc(&cow->refs);
 		rcu_assign_pointer(root->node, cow);
 
-		btrfs_free_tree_block(trans, root, buf, parent_start,
-				      last_ref);
+		btrfs_free_tree_block(trans, btrfs_root_id(root), buf,
+				      parent_start, last_ref);
 		free_extent_buffer(buf);
 		add_root_to_dirty_list(root);
 	} else {
@@ -484,9 +499,11 @@
 				return ret;
 			}
 		}
-		btrfs_free_tree_block(trans, root, buf, parent_start,
-				      last_ref);
+		btrfs_free_tree_block(trans, btrfs_root_id(root), buf,
+				      parent_start, last_ref);
 	}
+
+	trace_btrfs_cow_block(root, buf, cow);
 	if (unlock_orig)
 		btrfs_tree_unlock(buf);
 	free_extent_buffer_stale(buf);
@@ -526,7 +543,7 @@
 }
 
 /*
- * cows a single block, see __btrfs_cow_block for the real work.
+ * COWs a single block, see btrfs_force_cow_block() for the real work.
  * This version of it has extra checks so that a block isn't COWed more than
  * once per transaction, as long as it hasn't been written yet
  */
@@ -538,20 +555,31 @@
 {
 	struct btrfs_fs_info *fs_info = root->fs_info;
 	u64 search_start;
-	int ret;
 
-	if (test_bit(BTRFS_ROOT_DELETING, &root->state))
-		btrfs_err(fs_info,
-			"COW'ing blocks on a fs root that's being dropped");
-
-	if (trans->transaction != fs_info->running_transaction)
-		WARN(1, KERN_CRIT "trans %llu running %llu\n",
-		       trans->transid,
-		       fs_info->running_transaction->transid);
-
-	if (trans->transid != fs_info->generation)
-		WARN(1, KERN_CRIT "trans %llu running %llu\n",
-		       trans->transid, fs_info->generation);
+	if (unlikely(test_bit(BTRFS_ROOT_DELETING, &root->state))) {
+		btrfs_abort_transaction(trans, -EUCLEAN);
+		btrfs_crit(fs_info,
+		   "attempt to COW block %llu on root %llu that is being deleted",
+			   buf->start, btrfs_root_id(root));
+		return -EUCLEAN;
+	}
+
+	/*
+	 * COWing must happen through a running transaction, which always
+	 * matches the current fs generation (it's a transaction with a state
+	 * less than TRANS_STATE_UNBLOCKED). If it doesn't, then turn the fs
+	 * into error state to prevent the commit of any transaction.
+	 */
+	if (unlikely(trans->transaction != fs_info->running_transaction ||
+		     trans->transid != fs_info->generation)) {
+		btrfs_abort_transaction(trans, -EUCLEAN);
+		btrfs_crit(fs_info,
+"unexpected transaction when attempting to COW block %llu on root %llu, transaction %llu running transaction %llu fs generation %llu",
+			   buf->start, btrfs_root_id(root), trans->transid,
+			   fs_info->running_transaction->transid,
+			   fs_info->generation);
+		return -EUCLEAN;
+	}
 
 	if (!should_cow_block(trans, root, buf)) {
 		*cow_ret = buf;
@@ -567,12 +595,8 @@
 	 * Also We don't care about the error, as it's handled internally.
 	 */
 	btrfs_qgroup_trace_subtree_after_cow(trans, root, buf);
-	ret = __btrfs_cow_block(trans, root, buf, parent,
-				 parent_slot, cow_ret, search_start, 0, nest);
-
-	trace_btrfs_cow_block(root, buf, *cow_ret);
-
-	return ret;
+	return btrfs_force_cow_block(trans, root, buf, parent, parent_slot,
+				     cow_ret, search_start, 0, nest);
 }
 ALLOW_ERROR_INJECTION(btrfs_cow_block, ERRNO);
 
@@ -663,8 +687,22 @@
 	int progress_passed = 0;
 	struct btrfs_disk_key disk_key;
 
-	WARN_ON(trans->transaction != fs_info->running_transaction);
-	WARN_ON(trans->transid != fs_info->generation);
+	/*
+	 * COWing must happen through a running transaction, which always
+	 * matches the current fs generation (it's a transaction with a state
+	 * less than TRANS_STATE_UNBLOCKED). If it doesn't, then turn the fs
+	 * into error state to prevent the commit of any transaction.
+	 */
+	if (unlikely(trans->transaction != fs_info->running_transaction ||
+		     trans->transid != fs_info->generation)) {
+		btrfs_abort_transaction(trans, -EUCLEAN);
+		btrfs_crit(fs_info,
+"unexpected transaction when attempting to reallocate parent %llu for root %llu, transaction %llu running transaction %llu fs generation %llu",
+			   parent->start, btrfs_root_id(root), trans->transid,
+			   fs_info->running_transaction->transid,
+			   fs_info->generation);
+		return -EUCLEAN;
+	}
 
 	parent_nritems = btrfs_header_nritems(parent);
 	blocksize = fs_info->nodesize;
@@ -705,11 +743,11 @@
 			search_start = last_block;
 
 		btrfs_tree_lock(cur);
-		err = __btrfs_cow_block(trans, root, cur, parent, i,
-					&cur, search_start,
-					min(16 * blocksize,
-					    (end_slot - i) * blocksize),
-					BTRFS_NESTING_COW);
+		err = btrfs_force_cow_block(trans, root, cur, parent, i,
+					    &cur, search_start,
+					    min(16 * blocksize,
+						(end_slot - i) * blocksize),
+					    BTRFS_NESTING_COW);
 		if (err) {
 			btrfs_tree_unlock(cur);
 			free_extent_buffer(cur);
@@ -912,7 +950,12 @@
 		}
 
 		ret = btrfs_tree_mod_log_insert_root(root->node, child, true);
-		BUG_ON(ret < 0);
+		if (ret < 0) {
+			btrfs_tree_unlock(child);
+			free_extent_buffer(child);
+			btrfs_abort_transaction(trans, ret);
+			goto enospc;
+		}
 		rcu_assign_pointer(root->node, child);
 
 		add_root_to_dirty_list(root);
@@ -926,7 +969,7 @@
 		free_extent_buffer(mid);
 
 		root_sub_used(root, mid->len);
-		btrfs_free_tree_block(trans, root, mid, 0, 1);
+		btrfs_free_tree_block(trans, btrfs_root_id(root), mid, 0, 1);
 		/* once for the root ptr */
 		free_extent_buffer_stale(mid);
 		return 0;
@@ -985,7 +1028,8 @@
 			btrfs_tree_unlock(right);
 			del_ptr(root, path, level + 1, pslot + 1);
 			root_sub_used(root, right->len);
-			btrfs_free_tree_block(trans, root, right, 0, 1);
+			btrfs_free_tree_block(trans, btrfs_root_id(root), right,
+					      0, 1);
 			free_extent_buffer_stale(right);
 			right = NULL;
 		} else {
@@ -993,7 +1037,10 @@
 			btrfs_node_key(right, &right_key, 0);
 			ret = btrfs_tree_mod_log_insert_key(parent, pslot + 1,
 					BTRFS_MOD_LOG_KEY_REPLACE, GFP_NOFS);
-			BUG_ON(ret < 0);
+			if (ret < 0) {
+				btrfs_abort_transaction(trans, ret);
+				goto enospc;
+			}
 			btrfs_set_node_key(parent, &right_key, pslot + 1);
 			btrfs_mark_buffer_dirty(parent);
 		}
@@ -1030,7 +1077,7 @@
 		btrfs_tree_unlock(mid);
 		del_ptr(root, path, level + 1, pslot);
 		root_sub_used(root, mid->len);
-		btrfs_free_tree_block(trans, root, mid, 0, 1);
+		btrfs_free_tree_block(trans, btrfs_root_id(root), mid, 0, 1);
 		free_extent_buffer_stale(mid);
 		mid = NULL;
 	} else {
@@ -1039,7 +1086,10 @@
 		btrfs_node_key(mid, &mid_key, 0);
 		ret = btrfs_tree_mod_log_insert_key(parent, pslot,
 				BTRFS_MOD_LOG_KEY_REPLACE, GFP_NOFS);
-		BUG_ON(ret < 0);
+		if (ret < 0) {
+			btrfs_abort_transaction(trans, ret);
+			goto enospc;
+		}
 		btrfs_set_node_key(parent, &mid_key, pslot);
 		btrfs_mark_buffer_dirty(parent);
 	}
@@ -1566,35 +1616,13 @@
 							struct btrfs_path *p,
 							int write_lock_level)
 {
-	struct btrfs_fs_info *fs_info = root->fs_info;
 	struct extent_buffer *b;
-	int root_lock;
+	int root_lock = 0;
 	int level = 0;
 
-	/* We try very hard to do read locks on the root */
-	root_lock = BTRFS_READ_LOCK;
-
 	if (p->search_commit_root) {
-		/*
-		 * The commit roots are read only so we always do read locks,
-		 * and we always must hold the commit_root_sem when doing
-		 * searches on them, the only exception is send where we don't
-		 * want to block transaction commits for a long time, so
-		 * we need to clone the commit root in order to avoid races
-		 * with transaction commits that create a snapshot of one of
-		 * the roots used by a send operation.
-		 */
-		if (p->need_commit_sem) {
-			down_read(&fs_info->commit_root_sem);
-			b = btrfs_clone_extent_buffer(root->commit_root);
-			up_read(&fs_info->commit_root_sem);
-			if (!b)
-				return ERR_PTR(-ENOMEM);
-
-		} else {
-			b = root->commit_root;
-			atomic_inc(&b->refs);
-		}
+		b = root->commit_root;
+		atomic_inc(&b->refs);
 		level = btrfs_header_level(b);
 		/*
 		 * Ensure that all callers have set skip_locking when
@@ -1611,6 +1639,9 @@
 		goto out;
 	}
 
+	/* We try very hard to do read locks on the root */
+	root_lock = BTRFS_READ_LOCK;
+
 	/*
 	 * If the level is set to maximum, we can skip trying to get the read
 	 * lock.
@@ -1637,6 +1668,17 @@
 	level = btrfs_header_level(b);
 
 out:
+	/*
+	 * The root may have failed to write out at some point, and thus is no
+	 * longer valid, return an error in this case.
+	 */
+	if (!extent_buffer_uptodate(b)) {
+		if (root_lock)
+			btrfs_tree_unlock_rw(b, root_lock);
+		free_extent_buffer(b);
+		return ERR_PTR(-EIO);
+	}
+
 	p->nodes[level] = b;
 	if (!p->skip_locking)
 		p->locks[level] = root_lock;
@@ -1646,6 +1688,42 @@
 	return b;
 }
 
+/*
+ * Replace the extent buffer at the lowest level of the path with a cloned
+ * version. The purpose is to be able to use it safely, after releasing the
+ * commit root semaphore, even if relocation is happening in parallel, the
+ * transaction used for relocation is committed and the extent buffer is
+ * reallocated in the next transaction.
+ *
+ * This is used in a context where the caller does not prevent transaction
+ * commits from happening, either by holding a transaction handle or holding
+ * some lock, while it's doing searches through a commit root.
+ * At the moment it's only used for send operations.
+ */
+static int finish_need_commit_sem_search(struct btrfs_path *path)
+{
+	const int i = path->lowest_level;
+	const int slot = path->slots[i];
+	struct extent_buffer *lowest = path->nodes[i];
+	struct extent_buffer *clone;
+
+	ASSERT(path->need_commit_sem);
+
+	if (!lowest)
+		return 0;
+
+	lockdep_assert_held_read(&lowest->fs_info->commit_root_sem);
+
+	clone = btrfs_clone_extent_buffer(lowest);
+	if (!clone)
+		return -ENOMEM;
+
+	btrfs_release_path(path);
+	path->nodes[i] = clone;
+	path->slots[i] = slot;
+
+	return 0;
+}
 
 /*
  * btrfs_search_slot - look for a key in a tree and perform necessary
@@ -1682,6 +1760,7 @@
 		      const struct btrfs_key *key, struct btrfs_path *p,
 		      int ins_len, int cow)
 {
+	struct btrfs_fs_info *fs_info;
 	struct extent_buffer *b;
 	int slot;
 	int ret;
@@ -1694,6 +1773,12 @@
 	int min_write_lock_level;
 	int prev_cmp;
 
+	if (!root)
+		return -EINVAL;
+
+	fs_info = root->fs_info;
+	might_sleep();
+
 	lowest_level = p->lowest_level;
 	WARN_ON(lowest_level && ins_len > 0);
 	WARN_ON(p->nodes[0] != NULL);
@@ -1723,6 +1808,11 @@
 
 	min_write_lock_level = write_lock_level;
 
+	if (p->need_commit_sem) {
+		ASSERT(p->search_commit_root);
+		down_read(&fs_info->commit_root_sem);
+	}
+
 again:
 	prev_cmp = -1;
 	b = btrfs_search_slot_get_root(root, p, write_lock_level);
@@ -1903,6 +1993,9 @@
 
 		if (!p->skip_locking) {
 			level = btrfs_header_level(b);
+
+			btrfs_maybe_reset_lockdep_class(root, b);
+
 			if (level <= write_lock_level) {
 				btrfs_tree_lock(b);
 				p->locks[level] = BTRFS_WRITE_LOCK;
@@ -1917,6 +2010,16 @@
 done:
 	if (ret < 0 && !p->skip_release_on_error)
 		btrfs_release_path(p);
+
+	if (p->need_commit_sem) {
+		int ret2;
+
+		ret2 = finish_need_commit_sem_search(p);
+		up_read(&fs_info->commit_root_sem);
+		if (ret2)
+			ret = ret2;
+	}
+
 	return ret;
 }
 ALLOW_ERROR_INJECTION(btrfs_search_slot, ERRNO);
@@ -2578,6 +2681,8 @@
 
 	ret = btrfs_tree_mod_log_eb_copy(split, c, 0, mid, c_nritems - mid);
 	if (ret) {
+		btrfs_tree_unlock(split);
+		free_extent_buffer(split);
 		btrfs_abort_transaction(trans, ret);
 		return ret;
 	}
@@ -2859,6 +2964,7 @@
 
 	if (check_sibling_keys(left, right)) {
 		ret = -EUCLEAN;
+		btrfs_abort_transaction(trans, ret);
 		btrfs_tree_unlock(right);
 		free_extent_buffer(right);
 		return ret;
@@ -3102,6 +3208,7 @@
 
 	if (check_sibling_keys(left, right)) {
 		ret = -EUCLEAN;
+		btrfs_abort_transaction(trans, ret);
 		goto out;
 	}
 	return __push_leaf_left(path, min_data_size,
@@ -4015,7 +4122,7 @@
 	root_sub_used(root, leaf->len);
 
 	atomic_inc(&leaf->refs);
-	btrfs_free_tree_block(trans, root, leaf, 0, 1);
+	btrfs_free_tree_block(trans, btrfs_root_id(root), leaf, 0, 1);
 	free_extent_buffer_stale(leaf);
 }
 /*
@@ -4141,10 +4248,12 @@
 int btrfs_prev_leaf(struct btrfs_root *root, struct btrfs_path *path)
 {
 	struct btrfs_key key;
+	struct btrfs_key orig_key;
 	struct btrfs_disk_key found_key;
 	int ret;
 
 	btrfs_item_key_to_cpu(path->nodes[0], &key, 0);
+	orig_key = key;
 
 	if (key.offset > 0) {
 		key.offset--;
@@ -4161,8 +4270,36 @@
 
 	btrfs_release_path(path);
 	ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
-	if (ret < 0)
+	if (ret <= 0)
 		return ret;
+
+	/*
+	 * Previous key not found. Even if we were at slot 0 of the leaf we had
+	 * before releasing the path and calling btrfs_search_slot(), we now may
+	 * be in a slot pointing to the same original key - this can happen if
+	 * after we released the path, one of more items were moved from a
+	 * sibling leaf into the front of the leaf we had due to an insertion
+	 * (see push_leaf_right()).
+	 * If we hit this case and our slot is > 0 and just decrement the slot
+	 * so that the caller does not process the same key again, which may or
+	 * may not break the caller, depending on its logic.
+	 */
+	if (path->slots[0] < btrfs_header_nritems(path->nodes[0])) {
+		btrfs_item_key(path->nodes[0], &found_key, path->slots[0]);
+		ret = comp_keys(&found_key, &orig_key);
+		if (ret == 0) {
+			if (path->slots[0] > 0) {
+				path->slots[0]--;
+				return 0;
+			}
+			/*
+			 * At slot 0, same key as before, it means orig_key is
+			 * the lowest, leftmost, key in the tree. We're done.
+			 */
+			return 1;
+		}
+	}
+
 	btrfs_item_key(path->nodes[0], &found_key, 0);
 	ret = comp_keys(&found_key, &key);
 	/*
@@ -4385,7 +4522,9 @@
 	int level;
 	struct extent_buffer *c;
 	struct extent_buffer *next;
+	struct btrfs_fs_info *fs_info = root->fs_info;
 	struct btrfs_key key;
+	bool need_commit_sem = false;
 	u32 nritems;
 	int ret;
 	int i;
@@ -4402,14 +4541,20 @@
 
 	path->keep_locks = 1;
 
-	if (time_seq)
+	if (time_seq) {
 		ret = btrfs_search_old_slot(root, &key, path, time_seq);
-	else
+	} else {
+		if (path->need_commit_sem) {
+			path->need_commit_sem = 0;
+			need_commit_sem = true;
+			down_read(&fs_info->commit_root_sem);
+		}
 		ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
+	}
 	path->keep_locks = 0;
 
 	if (ret < 0)
-		return ret;
+		goto done;
 
 	nritems = btrfs_header_nritems(path->nodes[0]);
 	/*
@@ -4532,6 +4677,15 @@
 	ret = 0;
 done:
 	unlock_up(path, 0, 1, 0, NULL);
+	if (need_commit_sem) {
+		int ret2;
+
+		path->need_commit_sem = 1;
+		ret2 = finish_need_commit_sem_search(path);
+		up_read(&fs_info->commit_root_sem);
+		if (ret2)
+			ret = ret2;
+	}
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/ctree.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/ctree.h
@@ -105,14 +105,6 @@
 #define BTRFS_STAT_CURR		0
 #define BTRFS_STAT_PREV		1
 
-/*
- * Count how many BTRFS_MAX_EXTENT_SIZE cover the @size
- */
-static inline u32 count_max_extents(u64 size)
-{
-	return div_u64(size + BTRFS_MAX_EXTENT_SIZE - 1, BTRFS_MAX_EXTENT_SIZE);
-}
-
 static inline unsigned long btrfs_chunk_item_size(int num_stripes)
 {
 	BUG_ON(num_stripes == 0);
@@ -142,6 +134,9 @@
 	BTRFS_FS_STATE_DEV_REPLACING,
 	/* The btrfs_fs_info created for self-tests */
 	BTRFS_FS_STATE_DUMMY_FS_INFO,
+
+	/* Indicates there was an error cleaning up a log tree. */
+	BTRFS_FS_STATE_LOG_CLEANUP_ERROR,
 };
 
 #define BTRFS_BACKREF_REV_MAX		256
@@ -287,6 +282,26 @@
 #define BTRFS_FEATURE_COMPAT_RO_SAFE_SET	0ULL
 #define BTRFS_FEATURE_COMPAT_RO_SAFE_CLEAR	0ULL
 
+#ifdef CONFIG_BTRFS_DEBUG
+/*
+ * Extent tree v2 supported only with CONFIG_BTRFS_DEBUG
+ */
+#define BTRFS_FEATURE_INCOMPAT_SUPP			\
+	(BTRFS_FEATURE_INCOMPAT_MIXED_BACKREF |		\
+	 BTRFS_FEATURE_INCOMPAT_DEFAULT_SUBVOL |	\
+	 BTRFS_FEATURE_INCOMPAT_MIXED_GROUPS |		\
+	 BTRFS_FEATURE_INCOMPAT_BIG_METADATA |		\
+	 BTRFS_FEATURE_INCOMPAT_COMPRESS_LZO |		\
+	 BTRFS_FEATURE_INCOMPAT_COMPRESS_ZSTD |		\
+	 BTRFS_FEATURE_INCOMPAT_RAID56 |		\
+	 BTRFS_FEATURE_INCOMPAT_EXTENDED_IREF |		\
+	 BTRFS_FEATURE_INCOMPAT_SKINNY_METADATA |	\
+	 BTRFS_FEATURE_INCOMPAT_NO_HOLES	|	\
+	 BTRFS_FEATURE_INCOMPAT_METADATA_UUID	|	\
+	 BTRFS_FEATURE_INCOMPAT_RAID1C34	|	\
+	 BTRFS_FEATURE_INCOMPAT_ZONED		|	\
+	 BTRFS_FEATURE_INCOMPAT_EXTENT_TREE_V2)
+#else
 #define BTRFS_FEATURE_INCOMPAT_SUPP			\
 	(BTRFS_FEATURE_INCOMPAT_MIXED_BACKREF |		\
 	 BTRFS_FEATURE_INCOMPAT_DEFAULT_SUBVOL |	\
@@ -301,6 +316,7 @@
 	 BTRFS_FEATURE_INCOMPAT_METADATA_UUID	|	\
 	 BTRFS_FEATURE_INCOMPAT_RAID1C34	|	\
 	 BTRFS_FEATURE_INCOMPAT_ZONED)
+#endif
 
 #define BTRFS_FEATURE_INCOMPAT_SAFE_SET			\
 	(BTRFS_FEATURE_INCOMPAT_EXTENDED_IREF)
@@ -459,7 +475,6 @@
 enum btrfs_caching_type {
 	BTRFS_CACHE_NO,
 	BTRFS_CACHE_STARTED,
-	BTRFS_CACHE_FAST,
 	BTRFS_CACHE_FINISHED,
 	BTRFS_CACHE_ERROR,
 };
@@ -542,8 +557,6 @@
 	int bg_extent_count;
 };
 
-bool btrfs_pinned_by_swapfile(struct btrfs_fs_info *fs_info, void *ptr);
-
 enum {
 	BTRFS_FS_BARRIER,
 	BTRFS_FS_CLOSING_START,
@@ -568,7 +581,6 @@
 	/*
 	 * Indicate that relocation of a chunk has started, it's set per chunk
 	 * and is toggled between chunks.
-	 * Set, tested and cleared while holding fs_info::send_reloc_lock.
 	 */
 	BTRFS_FS_RELOC_RUNNING,
 
@@ -593,6 +605,9 @@
 	/* Indicate whether there are any tree modification log users */
 	BTRFS_FS_TREE_MOD_LOG_USERS,
 
+	/* Indicate we have half completed snapshot deletions pending. */
+	BTRFS_FS_UNFINISHED_DROPS,
+
 #if BITS_PER_LONG == 32
 	/* Indicate if we have error/warn message printed on 32bit systems */
 	BTRFS_FS_32BIT_ERROR,
@@ -665,6 +680,12 @@
 
 	u64 generation;
 	u64 last_trans_committed;
+	/*
+	 * Generation of the last transaction used for block group relocation
+	 * since the filesystem was last mounted (or 0 if none happened yet).
+	 * Must be written and read while holding btrfs_fs_info::commit_root_sem.
+	 */
+	u64 last_reloc_trans;
 	u64 avg_delayed_ref_runtime;
 
 	/*
@@ -988,19 +1009,18 @@
 	u32 csums_per_leaf;
 	u32 stripesize;
 
+	/*
+	 * Maximum size of an extent. BTRFS_MAX_EXTENT_SIZE on regular
+	 * filesystem, on zoned it depends on the device constraints.
+	 */
+	u64 max_extent_size;
+
 	/* Block groups and devices containing active swapfiles. */
 	spinlock_t swapfile_pins_lock;
 	struct rb_root swapfile_pins;
 
 	struct crypto_shash *csum_shash;
 
-	spinlock_t send_reloc_lock;
-	/*
-	 * Number of send operations in progress.
-	 * Updated while holding fs_info::send_reloc_lock.
-	 */
-	int send_in_progress;
-
 	/* Type of exclusive operation running, protected by super_lock */
 	enum btrfs_exclusive_operation exclusive_operation;
 
@@ -1013,10 +1033,20 @@
 		u64 zoned;
 	};
 
+	/* Max size to emit ZONE_APPEND write command */
+	u64 max_zone_append_size;
 	struct mutex zoned_meta_io_lock;
 	spinlock_t treelog_bg_lock;
 	u64 treelog_bg;
 
+	/*
+	 * Start of the dedicated data relocation block group, protected by
+	 * relocation_bg_lock.
+	 */
+	spinlock_t relocation_bg_lock;
+	u64 data_reloc_bg;
+	struct mutex zoned_data_reloc_io_lock;
+
 #ifdef CONFIG_BTRFS_FS_REF_VERIFY
 	spinlock_t ref_verify_lock;
 	struct rb_root block_tree;
@@ -1091,8 +1121,17 @@
 	BTRFS_ROOT_HAS_LOG_TREE,
 	/* Qgroup flushing is in progress */
 	BTRFS_ROOT_QGROUP_FLUSHING,
+	/* This root has a drop operation that was started previously. */
+	BTRFS_ROOT_UNFINISHED_DROP,
+	/* This reloc root needs to have its buffers lockdep class reset. */
+	BTRFS_ROOT_RESET_LOCKDEP_CLASS,
 };
 
+static inline void btrfs_wake_unfinished_drop(struct btrfs_fs_info *fs_info)
+{
+	clear_and_wake_up_bit(BTRFS_FS_UNFINISHED_DROPS, &fs_info->flags);
+}
+
 /*
  * Record swapped tree blocks of a subvolume tree for delayed subtree trace
  * code. For detail check comment in fs/btrfs/qgroup.c.
@@ -1343,6 +1382,7 @@
 
 struct btrfs_file_private {
 	void *filldir_buf;
+	u64 last_index;
 };
 
 
@@ -2238,6 +2278,11 @@
 	return (root->root_item.flags & cpu_to_le64(BTRFS_ROOT_SUBVOL_DEAD)) != 0;
 }
 
+static inline u64 btrfs_root_id(const struct btrfs_root *root)
+{
+	return root->root_key.objectid;
+}
+
 /* struct btrfs_root_backup */
 BTRFS_SETGET_STACK_FUNCS(backup_tree_root, struct btrfs_root_backup,
 		   tree_root, 64);
@@ -2700,7 +2745,7 @@
 					     u64 empty_size,
 					     enum btrfs_lock_nesting nest);
 void btrfs_free_tree_block(struct btrfs_trans_handle *trans,
-			   struct btrfs_root *root,
+			   u64 root_id,
 			   struct extent_buffer *buf,
 			   u64 parent, int last_ref);
 int btrfs_alloc_reserved_file_extent(struct btrfs_trans_handle *trans,
@@ -2840,6 +2885,13 @@
 		    struct extent_buffer *parent, int parent_slot,
 		    struct extent_buffer **cow_ret,
 		    enum btrfs_lock_nesting nest);
+int btrfs_force_cow_block(struct btrfs_trans_handle *trans,
+			  struct btrfs_root *root,
+			  struct extent_buffer *buf,
+			  struct extent_buffer *parent, int parent_slot,
+			  struct extent_buffer **cow_ret,
+			  u64 search_start, u64 empty_size,
+			  enum btrfs_lock_nesting nest);
 int btrfs_copy_root(struct btrfs_trans_handle *trans,
 		      struct btrfs_root *root,
 		      struct extent_buffer *buf,
@@ -3142,7 +3194,6 @@
 struct inode *btrfs_lookup_dentry(struct inode *dir, struct dentry *dentry);
 int btrfs_set_inode_index(struct btrfs_inode *dir, u64 *index);
 int btrfs_unlink_inode(struct btrfs_trans_handle *trans,
-		       struct btrfs_root *root,
 		       struct btrfs_inode *dir, struct btrfs_inode *inode,
 		       const char *name, int name_len);
 int btrfs_add_link(struct btrfs_trans_handle *trans,
@@ -3563,6 +3614,10 @@
 			  (errno), fmt, ##args);		\
 } while (0)
 
+#define BTRFS_FS_LOG_CLEANUP_ERROR(fs_info)				\
+	(unlikely(test_bit(BTRFS_FS_STATE_LOG_CLEANUP_ERROR,		\
+			   &(fs_info)->fs_state)))
+
 __printf(5, 6)
 __cold
 void __btrfs_panic(struct btrfs_fs_info *fs_info, const char *function,
@@ -3843,6 +3898,24 @@
 }
 
 /*
+ * Count how many fs_info->max_extent_size cover the @size
+ */
+static inline u32 count_max_extents(struct btrfs_fs_info *fs_info, u64 size)
+{
+#ifdef CONFIG_BTRFS_FS_RUN_SANITY_TESTS
+	if (!fs_info)
+		return div_u64(size + BTRFS_MAX_EXTENT_SIZE - 1, BTRFS_MAX_EXTENT_SIZE);
+#endif
+
+	return div_u64(size + fs_info->max_extent_size - 1, fs_info->max_extent_size);
+}
+
+static inline bool btrfs_is_data_reloc_root(const struct btrfs_root *root)
+{
+	return root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID;
+}
+
+/*
  * We use page status Private2 to indicate there is an ordered extent with
  * unfinished IO.
  *
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/delalloc-space.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/delalloc-space.c
@@ -143,10 +143,13 @@
 
 	/* Use new btrfs_qgroup_reserve_data to reserve precious data space. */
 	ret = btrfs_qgroup_reserve_data(inode, reserved, start, len);
-	if (ret < 0)
+	if (ret < 0) {
 		btrfs_free_reserved_data_space_noquota(fs_info, len);
-	else
+		extent_changeset_free(*reserved);
+		*reserved = NULL;
+	} else {
 		ret = 0;
+	}
 	return ret;
 }
 
@@ -270,7 +273,7 @@
 				    u64 num_bytes, u64 *meta_reserve,
 				    u64 *qgroup_reserve)
 {
-	u64 nr_extents = count_max_extents(num_bytes);
+	u64 nr_extents = count_max_extents(fs_info, num_bytes);
 	u64 csum_leaves = btrfs_csum_bytes_to_leaves(fs_info, num_bytes);
 	u64 inode_update = btrfs_calc_metadata_size(fs_info, 1);
 
@@ -309,9 +312,6 @@
 	} else {
 		if (current->journal_info)
 			flush = BTRFS_RESERVE_FLUSH_LIMIT;
-
-		if (btrfs_transaction_in_commit(fs_info))
-			schedule_timeout(1);
 	}
 
 	num_bytes = ALIGN(num_bytes, fs_info->sectorsize);
@@ -344,7 +344,7 @@
 	 * needs to free the reservation we just made.
 	 */
 	spin_lock(&inode->lock);
-	nr_extents = count_max_extents(num_bytes);
+	nr_extents = count_max_extents(fs_info, num_bytes);
 	btrfs_mod_outstanding_extents(inode, nr_extents);
 	inode->csum_bytes += num_bytes;
 	btrfs_calculate_inode_block_rsv_size(fs_info, inode);
@@ -407,7 +407,7 @@
 	unsigned num_extents;
 
 	spin_lock(&inode->lock);
-	num_extents = count_max_extents(num_bytes);
+	num_extents = count_max_extents(fs_info, num_bytes);
 	btrfs_mod_outstanding_extents(inode, -num_extents);
 	btrfs_calculate_inode_block_rsv_size(fs_info, inode);
 	spin_unlock(&inode->lock);
@@ -452,8 +452,11 @@
 	if (ret < 0)
 		return ret;
 	ret = btrfs_delalloc_reserve_metadata(inode, len);
-	if (ret < 0)
+	if (ret < 0) {
 		btrfs_free_reserved_data_space(inode, *reserved, start, len);
+		extent_changeset_free(*reserved);
+		*reserved = NULL;
+	}
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/delayed-inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/delayed-inode.c
@@ -901,7 +901,7 @@
 
 	if (delayed_node &&
 	    test_bit(BTRFS_DELAYED_NODE_INODE_DIRTY, &delayed_node->flags)) {
-		BUG_ON(!delayed_node->root);
+		ASSERT(delayed_node->root);
 		clear_bit(BTRFS_DELAYED_NODE_INODE_DIRTY, &delayed_node->flags);
 		delayed_node->count--;
 
@@ -1046,6 +1046,9 @@
 	if (ret)
 		return ret;
 
+	ret = btrfs_record_root_in_trans(trans, node->root);
+	if (ret)
+		return ret;
 	ret = btrfs_update_delayed_inode(trans, node->root, path, node);
 	return ret;
 }
@@ -1083,20 +1086,33 @@
 		ret = __btrfs_commit_inode_delayed_items(trans, path,
 							 curr_node);
 		if (ret) {
-			btrfs_release_delayed_node(curr_node);
-			curr_node = NULL;
 			btrfs_abort_transaction(trans, ret);
 			break;
 		}
 
 		prev_node = curr_node;
 		curr_node = btrfs_next_delayed_node(curr_node);
+		/*
+		 * See the comment below about releasing path before releasing
+		 * node. If the commit of delayed items was successful the path
+		 * should always be released, but in case of an error, it may
+		 * point to locked extent buffers (a leaf at the very least).
+		 */
+		ASSERT(path->nodes[0] == NULL);
 		btrfs_release_delayed_node(prev_node);
 	}
 
+	/*
+	 * Release the path to avoid a potential deadlock and lockdep splat when
+	 * releasing the delayed node, as that requires taking the delayed node's
+	 * mutex. If another task starts running delayed items before we take
+	 * the mutex, it will first lock the mutex and then it may try to lock
+	 * the same btree path (leaf).
+	 */
+	btrfs_free_path(path);
+
 	if (curr_node)
 		btrfs_release_delayed_node(curr_node);
-	btrfs_free_path(path);
 	trans->block_rsv = block_rsv;
 
 	return ret;
@@ -1388,9 +1404,10 @@
 	ret = __btrfs_add_delayed_insertion_item(delayed_node, delayed_item);
 	if (unlikely(ret)) {
 		btrfs_err(trans->fs_info,
-			  "err add delayed dir index item(name: %.*s) into the insertion tree of the delayed node(root id: %llu, inode id: %llu, errno: %d)",
-			  name_len, name, delayed_node->root->root_key.objectid,
-			  delayed_node->inode_id, ret);
+"error adding delayed dir index item, name: %.*s, index: %llu, root: %llu, dir: %llu, dir->index_cnt: %llu, delayed_node->index_cnt: %llu, error: %d",
+			  name_len, name, index, btrfs_root_id(delayed_node->root),
+			  delayed_node->inode_id, dir->index_cnt,
+			  delayed_node->index_cnt, ret);
 		BUG();
 	}
 	mutex_unlock(&delayed_node->mutex);
@@ -1499,6 +1516,7 @@
 }
 
 bool btrfs_readdir_get_delayed_items(struct inode *inode,
+				     u64 last_index,
 				     struct list_head *ins_list,
 				     struct list_head *del_list)
 {
@@ -1518,14 +1536,14 @@
 
 	mutex_lock(&delayed_node->mutex);
 	item = __btrfs_first_delayed_insertion_item(delayed_node);
-	while (item) {
+	while (item && item->key.offset <= last_index) {
 		refcount_inc(&item->refs);
 		list_add_tail(&item->readdir_list, ins_list);
 		item = __btrfs_next_delayed_item(item);
 	}
 
 	item = __btrfs_first_delayed_deletion_item(delayed_node);
-	while (item) {
+	while (item && item->key.offset <= last_index) {
 		refcount_inc(&item->refs);
 		list_add_tail(&item->readdir_list, del_list);
 		item = __btrfs_next_delayed_item(item);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/delayed-inode.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/delayed-inode.h
@@ -123,6 +123,7 @@
 
 /* Used for readdir() */
 bool btrfs_readdir_get_delayed_items(struct inode *inode,
+				     u64 last_index,
 				     struct list_head *ins_list,
 				     struct list_head *del_list);
 void btrfs_readdir_put_delayed_items(struct inode *inode,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/delayed-ref.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/delayed-ref.c
@@ -608,7 +608,7 @@
 					      &href->ref_add_list);
 			else if (ref->action == BTRFS_DROP_DELAYED_REF) {
 				ASSERT(!list_empty(&exist->add_list));
-				list_del(&exist->add_list);
+				list_del_init(&exist->add_list);
 			} else {
 				ASSERT(0);
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/delayed-ref.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/delayed-ref.h
@@ -271,7 +271,7 @@
 }
 
 static inline void btrfs_init_tree_ref(struct btrfs_ref *generic_ref,
-				int level, u64 root)
+				int level, u64 root, u64 mod_root, bool skip_qgroup)
 {
 	/* If @real_root not set, use @root as fallback */
 	if (!generic_ref->real_root)
@@ -282,7 +282,8 @@
 }
 
 static inline void btrfs_init_data_ref(struct btrfs_ref *generic_ref,
-				u64 ref_root, u64 ino, u64 offset)
+				u64 ref_root, u64 ino, u64 offset, u64 mod_root,
+				bool skip_qgroup)
 {
 	/* If @real_root not set, use @root as fallback */
 	if (!generic_ref->real_root)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/dev-replace.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/dev-replace.c
@@ -70,6 +70,7 @@
 
 int btrfs_init_dev_replace(struct btrfs_fs_info *fs_info)
 {
+	struct btrfs_dev_lookup_args args = { .devid = BTRFS_DEV_REPLACE_DEVID };
 	struct btrfs_key key;
 	struct btrfs_root *dev_root = fs_info->dev_root;
 	struct btrfs_dev_replace *dev_replace = &fs_info->dev_replace;
@@ -100,8 +101,7 @@
 		 * We don't have a replace item or it's corrupted.  If there is
 		 * a replace target, fail the mount.
 		 */
-		if (btrfs_find_device(fs_info->fs_devices,
-				      BTRFS_DEV_REPLACE_DEVID, NULL, NULL)) {
+		if (btrfs_find_device(fs_info->fs_devices, &args)) {
 			btrfs_err(fs_info,
 			"found replace target device without a valid replace item");
 			ret = -EUCLEAN;
@@ -163,10 +163,9 @@
 		 * We don't have an active replace item but if there is a
 		 * replace target, fail the mount.
 		 */
-		if (btrfs_find_device(fs_info->fs_devices,
-				      BTRFS_DEV_REPLACE_DEVID, NULL, NULL)) {
+		if (btrfs_find_device(fs_info->fs_devices, &args)) {
 			btrfs_err(fs_info,
-			"replace devid present without an active replace item");
+"replace without active item, run 'device scan --forget' on the target device");
 			ret = -EUCLEAN;
 		} else {
 			dev_replace->srcdev = NULL;
@@ -175,11 +174,10 @@
 		break;
 	case BTRFS_IOCTL_DEV_REPLACE_STATE_STARTED:
 	case BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED:
-		dev_replace->srcdev = btrfs_find_device(fs_info->fs_devices,
-						src_devid, NULL, NULL);
-		dev_replace->tgtdev = btrfs_find_device(fs_info->fs_devices,
-							BTRFS_DEV_REPLACE_DEVID,
-							NULL, NULL);
+		dev_replace->tgtdev = btrfs_find_device(fs_info->fs_devices, &args);
+		args.devid = src_devid;
+		dev_replace->srcdev = btrfs_find_device(fs_info->fs_devices, &args);
+
 		/*
 		 * allow 'btrfs dev replace_cancel' if src/tgt device is
 		 * missing
@@ -325,7 +323,7 @@
 	set_blocksize(device->bdev, BTRFS_BDEV_BLOCKSIZE);
 	device->fs_devices = fs_info->fs_devices;
 
-	ret = btrfs_get_dev_zone_info(device);
+	ret = btrfs_get_dev_zone_info(device, false);
 	if (ret)
 		goto error;
 
@@ -765,6 +763,23 @@
 	return ret;
 }
 
+static int btrfs_check_replace_dev_names(struct btrfs_ioctl_dev_replace_args *args)
+{
+	if (args->start.srcdevid == 0) {
+		if (memchr(args->start.srcdev_name, 0,
+			   sizeof(args->start.srcdev_name)) == NULL)
+			return -ENAMETOOLONG;
+	} else {
+		args->start.srcdev_name[0] = 0;
+	}
+
+	if (memchr(args->start.tgtdev_name, 0,
+		   sizeof(args->start.tgtdev_name)) == NULL)
+	    return -ENAMETOOLONG;
+
+	return 0;
+}
+
 int btrfs_dev_replace_by_ioctl(struct btrfs_fs_info *fs_info,
 			    struct btrfs_ioctl_dev_replace_args *args)
 {
@@ -777,10 +792,9 @@
 	default:
 		return -EINVAL;
 	}
-
-	if ((args->start.srcdevid == 0 && args->start.srcdev_name[0] == '\0') ||
-	    args->start.tgtdev_name[0] == '\0')
-		return -EINVAL;
+	ret = btrfs_check_replace_dev_names(args);
+	if (ret < 0)
+		return ret;
 
 	ret = btrfs_dev_replace_start(fs_info, args->start.tgtdev_name,
 					args->start.srcdevid,
@@ -1153,8 +1167,7 @@
 		up_write(&dev_replace->rwsem);
 
 		/* Scrub for replace must not be running in suspended state */
-		ret = btrfs_scrub_cancel(fs_info);
-		ASSERT(ret != -ENOTCONN);
+		btrfs_scrub_cancel(fs_info);
 
 		trans = btrfs_start_transaction(root, 0);
 		if (IS_ERR(trans)) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/discard.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/discard.c
@@ -77,6 +77,7 @@
 static void __add_to_discard_list(struct btrfs_discard_ctl *discard_ctl,
 				  struct btrfs_block_group *block_group)
 {
+	lockdep_assert_held(&discard_ctl->lock);
 	if (!btrfs_run_discard_work(discard_ctl))
 		return;
 
@@ -88,6 +89,8 @@
 						      BTRFS_DISCARD_DELAY);
 		block_group->discard_state = BTRFS_DISCARD_RESET_CURSOR;
 	}
+	if (list_empty(&block_group->discard_list))
+		btrfs_get_block_group(block_group);
 
 	list_move_tail(&block_group->discard_list,
 		       get_discard_list(discard_ctl, block_group));
@@ -107,8 +110,12 @@
 static void add_to_discard_unused_list(struct btrfs_discard_ctl *discard_ctl,
 				       struct btrfs_block_group *block_group)
 {
+	bool queued;
+
 	spin_lock(&discard_ctl->lock);
 
+	queued = !list_empty(&block_group->discard_list);
+
 	if (!btrfs_run_discard_work(discard_ctl)) {
 		spin_unlock(&discard_ctl->lock);
 		return;
@@ -120,6 +127,8 @@
 	block_group->discard_eligible_time = (ktime_get_ns() +
 					      BTRFS_DISCARD_UNUSED_DELAY);
 	block_group->discard_state = BTRFS_DISCARD_RESET_CURSOR;
+	if (!queued)
+		btrfs_get_block_group(block_group);
 	list_add_tail(&block_group->discard_list,
 		      &discard_ctl->discard_list[BTRFS_DISCARD_INDEX_UNUSED]);
 
@@ -130,6 +139,7 @@
 				     struct btrfs_block_group *block_group)
 {
 	bool running = false;
+	bool queued = false;
 
 	spin_lock(&discard_ctl->lock);
 
@@ -139,7 +149,16 @@
 	}
 
 	block_group->discard_eligible_time = 0;
+	queued = !list_empty(&block_group->discard_list);
 	list_del_init(&block_group->discard_list);
+	/*
+	 * If the block group is currently running in the discard workfn, we
+	 * don't want to deref it, since it's still being used by the workfn.
+	 * The workfn will notice this case and deref the block group when it is
+	 * finished.
+	 */
+	if (queued && !running)
+		btrfs_put_block_group(block_group);
 
 	spin_unlock(&discard_ctl->lock);
 
@@ -212,10 +231,12 @@
 	if (block_group && now >= block_group->discard_eligible_time) {
 		if (block_group->discard_index == BTRFS_DISCARD_INDEX_UNUSED &&
 		    block_group->used != 0) {
-			if (btrfs_is_block_group_data_only(block_group))
+			if (btrfs_is_block_group_data_only(block_group)) {
 				__add_to_discard_list(discard_ctl, block_group);
-			else
+			} else {
 				list_del_init(&block_group->discard_list);
+				btrfs_put_block_group(block_group);
+			}
 			goto again;
 		}
 		if (block_group->discard_state == BTRFS_DISCARD_RESET_CURSOR) {
@@ -502,6 +523,15 @@
 	spin_lock(&discard_ctl->lock);
 	discard_ctl->prev_discard = trimmed;
 	discard_ctl->prev_discard_time = now;
+	/*
+	 * If the block group was removed from the discard list while it was
+	 * running in this workfn, then we didn't deref it, since this function
+	 * still owned that reference. But we set the discard_ctl->block_group
+	 * back to NULL, so we can use that condition to know that now we need
+	 * to deref the block_group.
+	 */
+	if (discard_ctl->block_group == NULL)
+		btrfs_put_block_group(block_group);
 	discard_ctl->block_group = NULL;
 	__btrfs_discard_schedule_work(discard_ctl, now, false);
 	spin_unlock(&discard_ctl->lock);
@@ -638,8 +668,12 @@
 	list_for_each_entry_safe(block_group, next, &fs_info->unused_bgs,
 				 bg_list) {
 		list_del_init(&block_group->bg_list);
-		btrfs_put_block_group(block_group);
 		btrfs_discard_queue_work(&fs_info->discard_ctl, block_group);
+		/*
+		 * This put is for the get done by btrfs_mark_bg_unused.
+		 * Queueing discard incremented it for discard's reference.
+		 */
+		btrfs_put_block_group(block_group);
 	}
 	spin_unlock(&fs_info->unused_bgs_lock);
 }
@@ -669,6 +703,7 @@
 			if (block_group->used == 0)
 				btrfs_mark_bg_unused(block_group);
 			spin_lock(&discard_ctl->lock);
+			btrfs_put_block_group(block_group);
 		}
 	}
 	spin_unlock(&discard_ctl->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/disk-io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/disk-io.c
@@ -122,88 +122,6 @@
 };
 
 /*
- * Lockdep class keys for extent_buffer->lock's in this root.  For a given
- * eb, the lockdep key is determined by the btrfs_root it belongs to and
- * the level the eb occupies in the tree.
- *
- * Different roots are used for different purposes and may nest inside each
- * other and they require separate keysets.  As lockdep keys should be
- * static, assign keysets according to the purpose of the root as indicated
- * by btrfs_root->root_key.objectid.  This ensures that all special purpose
- * roots have separate keysets.
- *
- * Lock-nesting across peer nodes is always done with the immediate parent
- * node locked thus preventing deadlock.  As lockdep doesn't know this, use
- * subclass to avoid triggering lockdep warning in such cases.
- *
- * The key is set by the readpage_end_io_hook after the buffer has passed
- * csum validation but before the pages are unlocked.  It is also set by
- * btrfs_init_new_buffer on freshly allocated blocks.
- *
- * We also add a check to make sure the highest level of the tree is the
- * same as our lockdep setup here.  If BTRFS_MAX_LEVEL changes, this code
- * needs update as well.
- */
-#ifdef CONFIG_DEBUG_LOCK_ALLOC
-# if BTRFS_MAX_LEVEL != 8
-#  error
-# endif
-
-#define DEFINE_LEVEL(stem, level)					\
-	.names[level] = "btrfs-" stem "-0" #level,
-
-#define DEFINE_NAME(stem)						\
-	DEFINE_LEVEL(stem, 0)						\
-	DEFINE_LEVEL(stem, 1)						\
-	DEFINE_LEVEL(stem, 2)						\
-	DEFINE_LEVEL(stem, 3)						\
-	DEFINE_LEVEL(stem, 4)						\
-	DEFINE_LEVEL(stem, 5)						\
-	DEFINE_LEVEL(stem, 6)						\
-	DEFINE_LEVEL(stem, 7)
-
-static struct btrfs_lockdep_keyset {
-	u64			id;		/* root objectid */
-	/* Longest entry: btrfs-free-space-00 */
-	char			names[BTRFS_MAX_LEVEL][20];
-	struct lock_class_key	keys[BTRFS_MAX_LEVEL];
-} btrfs_lockdep_keysets[] = {
-	{ .id = BTRFS_ROOT_TREE_OBJECTID,	DEFINE_NAME("root")	},
-	{ .id = BTRFS_EXTENT_TREE_OBJECTID,	DEFINE_NAME("extent")	},
-	{ .id = BTRFS_CHUNK_TREE_OBJECTID,	DEFINE_NAME("chunk")	},
-	{ .id = BTRFS_DEV_TREE_OBJECTID,	DEFINE_NAME("dev")	},
-	{ .id = BTRFS_CSUM_TREE_OBJECTID,	DEFINE_NAME("csum")	},
-	{ .id = BTRFS_QUOTA_TREE_OBJECTID,	DEFINE_NAME("quota")	},
-	{ .id = BTRFS_TREE_LOG_OBJECTID,	DEFINE_NAME("log")	},
-	{ .id = BTRFS_TREE_RELOC_OBJECTID,	DEFINE_NAME("treloc")	},
-	{ .id = BTRFS_DATA_RELOC_TREE_OBJECTID,	DEFINE_NAME("dreloc")	},
-	{ .id = BTRFS_UUID_TREE_OBJECTID,	DEFINE_NAME("uuid")	},
-	{ .id = BTRFS_FREE_SPACE_TREE_OBJECTID,	DEFINE_NAME("free-space") },
-	{ .id = 0,				DEFINE_NAME("tree")	},
-};
-
-#undef DEFINE_LEVEL
-#undef DEFINE_NAME
-
-void btrfs_set_buffer_lockdep_class(u64 objectid, struct extent_buffer *eb,
-				    int level)
-{
-	struct btrfs_lockdep_keyset *ks;
-
-	BUG_ON(level >= ARRAY_SIZE(ks->keys));
-
-	/* find the matching keyset, id 0 is the default entry */
-	for (ks = btrfs_lockdep_keysets; ks->id; ks++)
-		if (ks->id == objectid)
-			break;
-
-	lockdep_set_class_and_name(&eb->lock,
-				   &ks->keys[level], ks->names[level]);
-}
-
-#endif
-
-/*
  * Compute the csum of a btree block and store the result to provided buffer.
  */
 static void csum_tree_block(struct extent_buffer *buf, u8 *result)
@@ -221,7 +139,7 @@
 	crypto_shash_update(shash, kaddr + BTRFS_CSUM_SIZE,
 			    first_page_part - BTRFS_CSUM_SIZE);
 
-	for (i = 1; i < num_pages; i++) {
+	for (i = 1; i < num_pages && INLINE_EXTENT_BUFFER_PAGES > 1; i++) {
 		kaddr = page_address(buf->pages[i]);
 		crypto_shash_update(shash, kaddr, PAGE_SIZE);
 	}
@@ -284,11 +202,9 @@
  * Return 0 if the superblock checksum type matches the checksum value of that
  * algorithm. Pass the raw disk superblock data.
  */
-static int btrfs_check_super_csum(struct btrfs_fs_info *fs_info,
-				  char *raw_disk_sb)
+int btrfs_check_super_csum(struct btrfs_fs_info *fs_info,
+			   const struct btrfs_super_block *disk_sb)
 {
-	struct btrfs_super_block *disk_sb =
-		(struct btrfs_super_block *)raw_disk_sb;
 	char result[BTRFS_CSUM_SIZE];
 	SHASH_DESC_ON_STACK(shash, fs_info->csum_shash);
 
@@ -299,7 +215,7 @@
 	 * BTRFS_SUPER_INFO_SIZE range, we expect that the unused space is
 	 * filled with zeros and is included in the checksum.
 	 */
-	crypto_shash_digest(shash, raw_disk_sb + BTRFS_CSUM_SIZE,
+	crypto_shash_digest(shash, (const u8 *)disk_sb + BTRFS_CSUM_SIZE,
 			    BTRFS_SUPER_INFO_SIZE - BTRFS_CSUM_SIZE, result);
 
 	if (memcmp(disk_sb->csum, result, fs_info->csum_size))
@@ -441,17 +357,38 @@
 	else
 		ret = btrfs_check_leaf_full(eb);
 
-	if (ret < 0) {
-		btrfs_print_tree(eb, 0);
+	if (ret < 0)
+		goto error;
+
+	/*
+	 * Also check the generation, the eb reached here must be newer than
+	 * last committed. Or something seriously wrong happened.
+	 */
+	if (unlikely(btrfs_header_generation(eb) <= fs_info->last_trans_committed)) {
+		ret = -EUCLEAN;
 		btrfs_err(fs_info,
-			"block=%llu write time tree block corruption detected",
-			eb->start);
-		WARN_ON(IS_ENABLED(CONFIG_BTRFS_DEBUG));
-		return ret;
+			"block=%llu bad generation, have %llu expect > %llu",
+			  eb->start, btrfs_header_generation(eb),
+			  fs_info->last_trans_committed);
+		goto error;
 	}
 	write_extent_buffer(eb, result, 0, fs_info->csum_size);
 
 	return 0;
+
+error:
+	btrfs_print_tree(eb, 0);
+	btrfs_err(fs_info, "block=%llu write time tree block corruption detected",
+		  eb->start);
+	/*
+	 * Be noisy if this is an extent buffer from a log tree. We don't abort
+	 * a transaction in case there's a bad log tree extent buffer, we just
+	 * fallback to a transaction commit. Still we want to know when there is
+	 * a bad log tree extent buffer, as that may signal a bug somewhere.
+	 */
+	WARN_ON(IS_ENABLED(CONFIG_BTRFS_DEBUG) ||
+		btrfs_header_owner(eb) == BTRFS_TREE_LOG_OBJECTID);
+	return ret;
 }
 
 /* Checksum all dirty extent buffers in one bio_vec */
@@ -1500,7 +1437,8 @@
 		goto fail;
 
 	if (root->root_key.objectid != BTRFS_TREE_LOG_OBJECTID &&
-	    root->root_key.objectid != BTRFS_DATA_RELOC_TREE_OBJECTID) {
+	    !btrfs_is_data_reloc_root(root) &&
+	    is_fstree(root->root_key.objectid)) {
 		set_bit(BTRFS_ROOT_SHAREABLE, &root->state);
 		btrfs_check_and_init_root_item(&root->root_item);
 	}
@@ -1662,12 +1600,12 @@
  *
  * @objectid:	root id
  * @anon_dev:	preallocated anonymous block device number for new roots,
- * 		pass 0 for new allocation.
+ *		pass NULL for a new allocation.
  * @check_ref:	whether to check root item references, If true, return -ENOENT
  *		for orphan roots
  */
 static struct btrfs_root *btrfs_get_root_ref(struct btrfs_fs_info *fs_info,
-					     u64 objectid, dev_t anon_dev,
+					     u64 objectid, dev_t *anon_dev,
 					     bool check_ref)
 {
 	struct btrfs_root *root;
@@ -1681,8 +1619,17 @@
 again:
 	root = btrfs_lookup_fs_root(fs_info, objectid);
 	if (root) {
-		/* Shouldn't get preallocated anon_dev for cached roots */
-		ASSERT(!anon_dev);
+		/*
+		 * Some other caller may have read out the newly inserted
+		 * subvolume already (for things like backref walk etc).  Not
+		 * that common but still possible.  In that case, we just need
+		 * to free the anon_dev.
+		 */
+		if (unlikely(anon_dev && *anon_dev)) {
+			free_anon_bdev(*anon_dev);
+			*anon_dev = 0;
+		}
+
 		if (check_ref && btrfs_root_refs(&root->root_item) == 0) {
 			btrfs_put_root(root);
 			return ERR_PTR(-ENOENT);
@@ -1702,7 +1649,7 @@
 		goto fail;
 	}
 
-	ret = btrfs_init_fs_root(root, anon_dev);
+	ret = btrfs_init_fs_root(root, anon_dev ? *anon_dev : 0);
 	if (ret)
 		goto fail;
 
@@ -1724,13 +1671,22 @@
 
 	ret = btrfs_insert_fs_root(fs_info, root);
 	if (ret) {
-		btrfs_put_root(root);
-		if (ret == -EEXIST)
+		if (ret == -EEXIST) {
+			btrfs_put_root(root);
 			goto again;
+		}
 		goto fail;
 	}
 	return root;
 fail:
+	/*
+	 * If our caller provided us an anonymous device, then it's his
+	 * responsability to free it in case we fail. So we have to set our
+	 * root's anon_dev to 0 to avoid a double free, once by btrfs_put_root()
+	 * and once again by our caller.
+	 */
+	if (anon_dev && *anon_dev)
+		root->anon_dev = 0;
 	btrfs_put_root(root);
 	return ERR_PTR(ret);
 }
@@ -1745,7 +1701,7 @@
 struct btrfs_root *btrfs_get_fs_root(struct btrfs_fs_info *fs_info,
 				     u64 objectid, bool check_ref)
 {
-	return btrfs_get_root_ref(fs_info, objectid, 0, check_ref);
+	return btrfs_get_root_ref(fs_info, objectid, NULL, check_ref);
 }
 
 /*
@@ -1753,11 +1709,11 @@
  * the anonymous block device id
  *
  * @objectid:	tree objectid
- * @anon_dev:	if zero, allocate a new anonymous block device or use the
- *		parameter value
+ * @anon_dev:	if NULL, allocate a new anonymous block device or use the
+ *		parameter value if not NULL
  */
 struct btrfs_root *btrfs_get_new_fs_root(struct btrfs_fs_info *fs_info,
-					 u64 objectid, dev_t anon_dev)
+					 u64 objectid, dev_t *anon_dev)
 {
 	return btrfs_get_root_ref(fs_info, objectid, anon_dev, true);
 }
@@ -2372,6 +2328,26 @@
 
 	fs_info->csum_shash = csum_shash;
 
+	/*
+	 * Check if the checksum implementation is a fast accelerated one.
+	 * As-is this is a bit of a hack and should be replaced once the csum
+	 * implementations provide that information themselves.
+	 */
+	switch (csum_type) {
+	case BTRFS_CSUM_TYPE_CRC32:
+		if (!strstr(crypto_shash_driver_name(csum_shash), "generic"))
+			set_bit(BTRFS_FS_CSUM_IMPL_FAST, &fs_info->flags);
+		break;
+	case BTRFS_CSUM_TYPE_XXHASH:
+		set_bit(BTRFS_FS_CSUM_IMPL_FAST, &fs_info->flags);
+		break;
+	default:
+		break;
+	}
+
+	btrfs_info(fs_info, "using %s (%s) checksum algorithm",
+			btrfs_super_csum_name(csum_type),
+			crypto_shash_driver_name(csum_shash));
 	return 0;
 }
 
@@ -2463,7 +2439,9 @@
 		fs_info->dev_root = root;
 	}
 	/* Initialize fs_info for all devices in any case */
-	btrfs_init_devices_late(fs_info);
+	ret = btrfs_init_devices_late(fs_info);
+	if (ret)
+		goto out;
 
 	/* If IGNOREDATACSUMS is set don't bother reading the csum root. */
 	if (!btrfs_test_opt(fs_info, IGNOREDATACSUMS)) {
@@ -2548,8 +2526,8 @@
  * 		1, 2	2nd and 3rd backup copy
  * 	       -1	skip bytenr check
  */
-static int validate_super(struct btrfs_fs_info *fs_info,
-			    struct btrfs_super_block *sb, int mirror_num)
+int btrfs_validate_super(struct btrfs_fs_info *fs_info,
+			 struct btrfs_super_block *sb, int mirror_num)
 {
 	u64 nodesize = btrfs_super_nodesize(sb);
 	u64 sectorsize = btrfs_super_sectorsize(sb);
@@ -2632,21 +2610,18 @@
 		ret = -EINVAL;
 	}
 
-	if (memcmp(fs_info->fs_devices->fsid, fs_info->super_copy->fsid,
-		   BTRFS_FSID_SIZE)) {
+	if (memcmp(fs_info->fs_devices->fsid, sb->fsid, BTRFS_FSID_SIZE) != 0) {
 		btrfs_err(fs_info,
 		"superblock fsid doesn't match fsid of fs_devices: %pU != %pU",
-			fs_info->super_copy->fsid, fs_info->fs_devices->fsid);
+			  sb->fsid, fs_info->fs_devices->fsid);
 		ret = -EINVAL;
 	}
 
-	if (btrfs_fs_incompat(fs_info, METADATA_UUID) &&
-	    memcmp(fs_info->fs_devices->metadata_uuid,
-		   fs_info->super_copy->metadata_uuid, BTRFS_FSID_SIZE)) {
+	if (memcmp(fs_info->fs_devices->metadata_uuid, btrfs_sb_fsid_ptr(sb),
+		   BTRFS_FSID_SIZE) != 0) {
 		btrfs_err(fs_info,
 "superblock metadata_uuid doesn't match metadata uuid of fs_devices: %pU != %pU",
-			fs_info->super_copy->metadata_uuid,
-			fs_info->fs_devices->metadata_uuid);
+			  btrfs_sb_fsid_ptr(sb), fs_info->fs_devices->metadata_uuid);
 		ret = -EINVAL;
 	}
 
@@ -2732,7 +2707,7 @@
  */
 static int btrfs_validate_mount_super(struct btrfs_fs_info *fs_info)
 {
-	return validate_super(fs_info, fs_info->super_copy, 0);
+	return btrfs_validate_super(fs_info, fs_info->super_copy, 0);
 }
 
 /*
@@ -2746,7 +2721,7 @@
 {
 	int ret;
 
-	ret = validate_super(fs_info, sb, -1);
+	ret = btrfs_validate_super(fs_info, sb, -1);
 	if (ret < 0)
 		goto out;
 	if (!btrfs_supported_super_csum(btrfs_super_csum_type(sb))) {
@@ -2851,6 +2826,7 @@
 		/* All successful */
 		fs_info->generation = generation;
 		fs_info->last_trans_committed = generation;
+		fs_info->last_reloc_trans = 0;
 
 		/* Always begin writing backup roots after the one being used */
 		if (backup_index < 0) {
@@ -2883,12 +2859,14 @@
 	spin_lock_init(&fs_info->buffer_lock);
 	spin_lock_init(&fs_info->unused_bgs_lock);
 	spin_lock_init(&fs_info->treelog_bg_lock);
+	spin_lock_init(&fs_info->relocation_bg_lock);
 	rwlock_init(&fs_info->tree_mod_log_lock);
 	mutex_init(&fs_info->unused_bg_unpin_mutex);
 	mutex_init(&fs_info->reclaim_bgs_lock);
 	mutex_init(&fs_info->reloc_mutex);
 	mutex_init(&fs_info->delalloc_root_mutex);
 	mutex_init(&fs_info->zoned_meta_io_lock);
+	mutex_init(&fs_info->zoned_data_reloc_io_lock);
 	seqlock_init(&fs_info->profiles_lock);
 
 	INIT_LIST_HEAD(&fs_info->dirty_cowonly_roots);
@@ -2980,12 +2958,11 @@
 	fs_info->sectorsize_bits = ilog2(4096);
 	fs_info->stripesize = 4096;
 
+	fs_info->max_extent_size = BTRFS_MAX_EXTENT_SIZE;
+
 	spin_lock_init(&fs_info->swapfile_pins_lock);
 	fs_info->swapfile_pins = RB_ROOT;
 
-	spin_lock_init(&fs_info->send_reloc_lock);
-	fs_info->send_in_progress = 0;
-
 	fs_info->bg_reclaim_threshold = BTRFS_DEFAULT_RECLAIM_THRESH;
 	INIT_WORK(&fs_info->reclaim_bgs_work, btrfs_reclaim_bgs_work);
 }
@@ -3228,12 +3205,12 @@
 	mapping_set_gfp_mask(fs_info->btree_inode->i_mapping, GFP_NOFS);
 	btrfs_init_btree_inode(fs_info);
 
-	invalidate_bdev(fs_devices->latest_bdev);
+	invalidate_bdev(fs_devices->latest_dev->bdev);
 
 	/*
 	 * Read super block and check the signature bytes only
 	 */
-	disk_super = btrfs_read_dev_super(fs_devices->latest_bdev);
+	disk_super = btrfs_read_dev_super(fs_devices->latest_dev->bdev);
 	if (IS_ERR(disk_super)) {
 		err = PTR_ERR(disk_super);
 		goto fail_alloc;
@@ -3265,7 +3242,7 @@
 	 * We want to check superblock checksum, the type is stored inside.
 	 * Pass the whole disk block of size BTRFS_SUPER_INFO_SIZE (4k).
 	 */
-	if (btrfs_check_super_csum(fs_info, (u8 *)disk_super)) {
+	if (btrfs_check_super_csum(fs_info, disk_super)) {
 		btrfs_err(fs_info, "superblock checksum mismatch");
 		err = -EINVAL;
 		btrfs_release_disk_super(disk_super);
@@ -3314,16 +3291,6 @@
 	 */
 	fs_info->compress_type = BTRFS_COMPRESS_ZLIB;
 
-	/*
-	 * Flag our filesystem as having big metadata blocks if they are bigger
-	 * than the page size.
-	 */
-	if (btrfs_super_nodesize(disk_super) > PAGE_SIZE) {
-		if (!(features & BTRFS_FEATURE_INCOMPAT_BIG_METADATA))
-			btrfs_info(fs_info,
-				"flagging fs with big metadata feature");
-		features |= BTRFS_FEATURE_INCOMPAT_BIG_METADATA;
-	}
 
 	/* Set up fs_info before parsing mount options */
 	nodesize = btrfs_super_nodesize(disk_super);
@@ -3348,7 +3315,7 @@
 		~BTRFS_FEATURE_INCOMPAT_SUPP;
 	if (features) {
 		btrfs_err(fs_info,
-		    "cannot mount because of unsupported optional features (%llx)",
+		    "cannot mount because of unsupported optional features (0x%llx)",
 		    features);
 		err = -EINVAL;
 		goto fail_alloc;
@@ -3365,6 +3332,17 @@
 		btrfs_info(fs_info, "has skinny extents");
 
 	/*
+	 * Flag our filesystem as having big metadata blocks if they are bigger
+	 * than the page size.
+	 */
+	if (btrfs_super_nodesize(disk_super) > PAGE_SIZE) {
+		if (!(features & BTRFS_FEATURE_INCOMPAT_BIG_METADATA))
+			btrfs_info(fs_info,
+				"flagging fs with big metadata feature");
+		features |= BTRFS_FEATURE_INCOMPAT_BIG_METADATA;
+	}
+
+	/*
 	 * mixed block groups end up with duplicate but slightly offset
 	 * extent buffers for the same range.  It leads to corruptions
 	 */
@@ -3386,13 +3364,24 @@
 		~BTRFS_FEATURE_COMPAT_RO_SUPP;
 	if (!sb_rdonly(sb) && features) {
 		btrfs_err(fs_info,
-	"cannot mount read-write because of unsupported optional features (%llx)",
+	"cannot mount read-write because of unsupported optional features (0x%llx)",
 		       features);
 		err = -EINVAL;
 		goto fail_alloc;
 	}
 
 	if (sectorsize != PAGE_SIZE) {
+		/*
+		 * V1 space cache has some hardcoded PAGE_SIZE usage, and is
+		 * going to be deprecated.
+		 *
+		 * Force to use v2 cache for subpage case.
+		 */
+		btrfs_clear_opt(fs_info->mount_opt, SPACE_CACHE);
+		btrfs_set_and_info(fs_info, FREE_SPACE_TREE,
+			"forcing free space tree for sector size %u with page size %lu",
+			sectorsize, PAGE_SIZE);
+
 		btrfs_warn(fs_info,
 		"read-write for sector size %u with page size %lu is experimental",
 			   sectorsize, PAGE_SIZE);
@@ -3465,7 +3454,7 @@
 	 * below in btrfs_init_dev_replace().
 	 */
 	btrfs_free_extra_devids(fs_devices);
-	if (!fs_devices->latest_bdev) {
+	if (!fs_devices->latest_dev->bdev) {
 		btrfs_err(fs_info, "failed to read devices");
 		goto fail_tree_roots;
 	}
@@ -3523,6 +3512,20 @@
 		btrfs_err(fs_info, "failed to init dev_replace: %d", ret);
 		goto fail_block_groups;
 	}
+	/*
+	 * We have unsupported RO compat features, although RO mounted, we
+	 * should not cause any metadata write, including log replay.
+	 * Or we could screw up whatever the new feature requires.
+	 */
+	if (unlikely(features && btrfs_super_log_root(disk_super) &&
+		     !btrfs_test_opt(fs_info, NOLOGREPLAY))) {
+		btrfs_err(fs_info,
+"cannot replay dirty log with unsupported compat_ro features (0x%llx), try rescue=nologreplay",
+			  features);
+		err = -EINVAL;
+		goto fail_alloc;
+	}
+
 
 	ret = btrfs_check_zoned_mode(fs_info);
 	if (ret) {
@@ -3556,7 +3559,10 @@
 		goto fail_sysfs;
 	}
 
-	if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
+	btrfs_free_zone_cache(fs_info);
+
+	if (!sb_rdonly(sb) && fs_info->fs_devices->missing_devices &&
+	    !btrfs_check_rw_degradable(fs_info, NULL)) {
 		btrfs_warn(fs_info,
 		"writable mount is not allowed due to too many missing devices");
 		goto fail_sysfs;
@@ -3647,6 +3653,10 @@
 
 	set_bit(BTRFS_FS_OPEN, &fs_info->flags);
 
+	/* Kick the cleaner thread so it'll start deleting snapshots. */
+	if (test_bit(BTRFS_FS_UNFINISHED_DROPS, &fs_info->flags))
+		wake_up_process(fs_info->cleaner_kthread);
+
 clear_oneshot:
 	btrfs_clear_oneshot_options(fs_info);
 	return 0;
@@ -3725,7 +3735,7 @@
 }
 
 struct btrfs_super_block *btrfs_read_dev_one_super(struct block_device *bdev,
-						   int copy_num)
+						   int copy_num, bool drop_cache)
 {
 	struct btrfs_super_block *super;
 	struct page *page;
@@ -3743,6 +3753,19 @@
 	if (bytenr + BTRFS_SUPER_INFO_SIZE >= i_size_read(bdev->bd_inode))
 		return ERR_PTR(-EINVAL);
 
+	if (drop_cache) {
+		/* This should only be called with the primary sb. */
+		ASSERT(copy_num == 0);
+
+		/*
+		 * Drop the page of the primary superblock, so later read will
+		 * always read from the device.
+		 */
+		invalidate_inode_pages2_range(mapping,
+				bytenr >> PAGE_SHIFT,
+				(bytenr + BTRFS_SUPER_INFO_SIZE) >> PAGE_SHIFT);
+	}
+
 	page = read_cache_page_gfp(mapping, bytenr >> PAGE_SHIFT, GFP_NOFS);
 	if (IS_ERR(page))
 		return ERR_CAST(page);
@@ -3774,7 +3797,7 @@
 	 * later supers, using BTRFS_SUPER_MIRROR_MAX instead
 	 */
 	for (i = 0; i < 1; i++) {
-		super = btrfs_read_dev_one_super(bdev, i);
+		super = btrfs_read_dev_one_super(bdev, i, false);
 		if (IS_ERR(super))
 			continue;
 
@@ -3968,11 +3991,23 @@
  */
 static void write_dev_flush(struct btrfs_device *device)
 {
-	struct request_queue *q = bdev_get_queue(device->bdev);
 	struct bio *bio = device->flush_bio;
 
+#ifndef CONFIG_BTRFS_FS_CHECK_INTEGRITY
+	/*
+	 * When a disk has write caching disabled, we skip submission of a bio
+	 * with flush and sync requests before writing the superblock, since
+	 * it's not needed. However when the integrity checker is enabled, this
+	 * results in reports that there are metadata blocks referred by a
+	 * superblock that were not properly flushed. So don't skip the bio
+	 * submission only when the integrity checker is enabled for the sake
+	 * of simplicity, since this is a debug tool and not meant for use in
+	 * non-debug builds.
+	 */
+	struct request_queue *q = bdev_get_queue(device->bdev);
 	if (!test_bit(QUEUE_FLAG_WC, &q->queue_flags))
 		return;
+#endif
 
 	bio_reset(bio);
 	bio->bi_end_io = btrfs_end_empty_barrier;
@@ -4308,6 +4343,28 @@
 	int ret;
 
 	set_bit(BTRFS_FS_CLOSING_START, &fs_info->flags);
+
+	/*
+	 * If we had UNFINISHED_DROPS we could still be processing them, so
+	 * clear that bit and wake up relocation so it can stop.
+	 * We must do this before stopping the block group reclaim task, because
+	 * at btrfs_relocate_block_group() we wait for this bit, and after the
+	 * wait we stop with -EINTR if btrfs_fs_closing() returns non-zero - we
+	 * have just set BTRFS_FS_CLOSING_START, so btrfs_fs_closing() will
+	 * return 1.
+	 */
+	btrfs_wake_unfinished_drop(fs_info);
+
+	/*
+	 * We may have the reclaim task running and relocating a data block group,
+	 * in which case it may create delayed iputs. So stop it before we park
+	 * the cleaner kthread otherwise we can get new delayed iputs after
+	 * parking the cleaner, and that can make the async reclaim task to hang
+	 * if it's waiting for delayed iputs to complete, since the cleaner is
+	 * parked and can not run delayed iputs - this will make us hang when
+	 * trying to stop the async reclaim task.
+	 */
+	cancel_work_sync(&fs_info->reclaim_bgs_work);
 	/*
 	 * We don't want the cleaner to start new transactions, add more delayed
 	 * iputs, etc. while we're closing. We can't use kthread_stop() yet
@@ -4338,12 +4395,55 @@
 	/* clear out the rbtree of defraggable inodes */
 	btrfs_cleanup_defrag_inodes(fs_info);
 
+	/*
+	 * Wait for any fixup workers to complete.
+	 * If we don't wait for them here and they are still running by the time
+	 * we call kthread_stop() against the cleaner kthread further below, we
+	 * get an use-after-free on the cleaner because the fixup worker adds an
+	 * inode to the list of delayed iputs and then attempts to wakeup the
+	 * cleaner kthread, which was already stopped and destroyed. We parked
+	 * already the cleaner, but below we run all pending delayed iputs.
+	 */
+	btrfs_flush_workqueue(fs_info->fixup_workers);
+	/*
+	 * Similar case here, we have to wait for delalloc workers before we
+	 * proceed below and stop the cleaner kthread, otherwise we trigger a
+	 * use-after-tree on the cleaner kthread task_struct when a delalloc
+	 * worker running submit_compressed_extents() adds a delayed iput, which
+	 * does a wake up on the cleaner kthread, which was already freed below
+	 * when we call kthread_stop().
+	 */
+	btrfs_flush_workqueue(fs_info->delalloc_workers);
+
+	/*
+	 * After we parked the cleaner kthread, ordered extents may have
+	 * completed and created new delayed iputs. If one of the async reclaim
+	 * tasks is running and in the RUN_DELAYED_IPUTS flush state, then we
+	 * can hang forever trying to stop it, because if a delayed iput is
+	 * added after it ran btrfs_run_delayed_iputs() and before it called
+	 * btrfs_wait_on_delayed_iputs(), it will hang forever since there is
+	 * no one else to run iputs.
+	 *
+	 * So wait for all ongoing ordered extents to complete and then run
+	 * delayed iputs. This works because once we reach this point no one
+	 * can either create new ordered extents nor create delayed iputs
+	 * through some other means.
+	 *
+	 * Also note that btrfs_wait_ordered_roots() is not safe here, because
+	 * it waits for BTRFS_ORDERED_COMPLETE to be set on an ordered extent,
+	 * but the delayed iput for the respective inode is made only when doing
+	 * the final btrfs_put_ordered_extent() (which must happen at
+	 * btrfs_finish_ordered_io() when we are unmounting).
+	 */
+	btrfs_flush_workqueue(fs_info->endio_write_workers);
+	/* Ordered extents for free space inodes. */
+	btrfs_flush_workqueue(fs_info->endio_freespace_worker);
+	btrfs_run_delayed_iputs(fs_info);
+
 	cancel_work_sync(&fs_info->async_reclaim_work);
 	cancel_work_sync(&fs_info->async_data_reclaim_work);
 	cancel_work_sync(&fs_info->preempt_reclaim_work);
 
-	cancel_work_sync(&fs_info->reclaim_bgs_work);
-
 	/* Cancel or finish ongoing discard work */
 	btrfs_discard_cleanup(fs_info);
 
@@ -4627,19 +4727,11 @@
 				      struct btrfs_fs_info *fs_info)
 {
 	struct rb_node *node;
-	struct btrfs_delayed_ref_root *delayed_refs;
+	struct btrfs_delayed_ref_root *delayed_refs = &trans->delayed_refs;
 	struct btrfs_delayed_ref_node *ref;
 	int ret = 0;
 
-	delayed_refs = &trans->delayed_refs;
-
 	spin_lock(&delayed_refs->lock);
-	if (atomic_read(&delayed_refs->num_entries) == 0) {
-		spin_unlock(&delayed_refs->lock);
-		btrfs_debug(fs_info, "delayed_refs has NO entry");
-		return ret;
-	}
-
 	while ((node = rb_first_cached(&delayed_refs->href_root)) != NULL) {
 		struct btrfs_delayed_ref_head *head;
 		struct rb_node *n;
@@ -4726,7 +4818,11 @@
 		 */
 		inode = igrab(&btrfs_inode->vfs_inode);
 		if (inode) {
+			unsigned int nofs_flag;
+
+			nofs_flag = memalloc_nofs_save();
 			invalidate_inode_pages2(inode->i_mapping);
+			memalloc_nofs_restore(nofs_flag);
 			iput(inode);
 		}
 		spin_lock(&root->delalloc_lock);
@@ -4831,7 +4927,12 @@
 
 	inode = cache->io_ctl.inode;
 	if (inode) {
+		unsigned int nofs_flag;
+
+		nofs_flag = memalloc_nofs_save();
 		invalidate_inode_pages2(inode->i_mapping);
+		memalloc_nofs_restore(nofs_flag);
+
 		BTRFS_I(inode)->generation = 0;
 		cache->io_ctl.inode = NULL;
 		iput(inode);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/disk-io.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/disk-io.h
@@ -52,14 +52,18 @@
 void btrfs_clean_tree_block(struct extent_buffer *buf);
 void btrfs_clear_oneshot_options(struct btrfs_fs_info *fs_info);
 int btrfs_start_pre_rw_mount(struct btrfs_fs_info *fs_info);
+int btrfs_check_super_csum(struct btrfs_fs_info *fs_info,
+			   const struct btrfs_super_block *disk_sb);
 int __cold open_ctree(struct super_block *sb,
 	       struct btrfs_fs_devices *fs_devices,
 	       char *options);
 void __cold close_ctree(struct btrfs_fs_info *fs_info);
+int btrfs_validate_super(struct btrfs_fs_info *fs_info,
+			 struct btrfs_super_block *sb, int mirror_num);
 int write_all_supers(struct btrfs_fs_info *fs_info, int max_mirrors);
 struct btrfs_super_block *btrfs_read_dev_super(struct block_device *bdev);
 struct btrfs_super_block *btrfs_read_dev_one_super(struct block_device *bdev,
-						   int copy_num);
+						   int copy_num, bool drop_cache);
 int btrfs_commit_super(struct btrfs_fs_info *fs_info);
 struct btrfs_root *btrfs_read_tree_root(struct btrfs_root *tree_root,
 					struct btrfs_key *key);
@@ -70,7 +74,7 @@
 struct btrfs_root *btrfs_get_fs_root(struct btrfs_fs_info *fs_info,
 				     u64 objectid, bool check_ref);
 struct btrfs_root *btrfs_get_new_fs_root(struct btrfs_fs_info *fs_info,
-					 u64 objectid, dev_t anon_dev);
+					 u64 objectid, dev_t *anon_dev);
 struct btrfs_root *btrfs_get_fs_root_commit_root(struct btrfs_fs_info *fs_info,
 						 struct btrfs_path *path,
 						 u64 objectid);
@@ -140,14 +144,4 @@
 int __init btrfs_end_io_wq_init(void);
 void __cold btrfs_end_io_wq_exit(void);
 
-#ifdef CONFIG_DEBUG_LOCK_ALLOC
-void btrfs_set_buffer_lockdep_class(u64 objectid,
-			            struct extent_buffer *eb, int level);
-#else
-static inline void btrfs_set_buffer_lockdep_class(u64 objectid,
-					struct extent_buffer *eb, int level)
-{
-}
-#endif
-
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/export.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/export.c
@@ -58,7 +58,7 @@
 }
 
 struct dentry *btrfs_get_dentry(struct super_block *sb, u64 objectid,
-				u64 root_objectid, u32 generation,
+				u64 root_objectid, u64 generation,
 				int check_generation)
 {
 	struct btrfs_fs_info *fs_info = btrfs_sb(sb);
@@ -161,8 +161,15 @@
 	ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
 	if (ret < 0)
 		goto fail;
+	if (ret == 0) {
+		/*
+		 * Key with offset of -1 found, there would have to exist an
+		 * inode with such number or a root with such id.
+		 */
+		ret = -EUCLEAN;
+		goto fail;
+	}
 
-	BUG_ON(ret == 0); /* Key with offset of -1 found */
 	if (path->slots[0] == 0) {
 		ret = -ENOENT;
 		goto fail;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/export.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/export.h
@@ -19,7 +19,7 @@
 } __attribute__ ((packed));
 
 struct dentry *btrfs_get_dentry(struct super_block *sb, u64 objectid,
-				u64 root_objectid, u32 generation,
+				u64 root_objectid, u64 generation,
 				int check_generation);
 struct dentry *btrfs_get_parent(struct dentry *child);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/extent-tree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/extent-tree.c
@@ -860,6 +860,11 @@
 		err = -ENOENT;
 		goto out;
 	} else if (WARN_ON(ret)) {
+		btrfs_print_leaf(path->nodes[0]);
+		btrfs_err(fs_info,
+"extent item not found for insert, bytenr %llu num_bytes %llu parent %llu root_objectid %llu owner %llu offset %llu",
+			  bytenr, num_bytes, parent, root_objectid, owner,
+			  offset);
 		err = -EIO;
 		goto out;
 	}
@@ -1201,7 +1206,8 @@
 	u64 bytes_left, end;
 	u64 aligned_start = ALIGN(start, 1 << 9);
 
-	if (WARN_ON(start != aligned_start)) {
+	/* Adjust the range to be aligned to 512B sectors if necessary. */
+	if (start != aligned_start) {
 		len -= aligned_start - start;
 		len = round_down(len, 1 << 9);
 		start = aligned_start;
@@ -1266,7 +1272,7 @@
 	return ret;
 }
 
-static int do_discard_extent(struct btrfs_bio_stripe *stripe, u64 *bytes)
+static int do_discard_extent(struct btrfs_io_stripe *stripe, u64 *bytes)
 {
 	struct btrfs_device *dev = stripe->dev;
 	struct btrfs_fs_info *fs_info = dev->fs_info;
@@ -1313,22 +1319,21 @@
 	u64 discarded_bytes = 0;
 	u64 end = bytenr + num_bytes;
 	u64 cur = bytenr;
-	struct btrfs_bio *bbio = NULL;
-
+	struct btrfs_io_context *bioc = NULL;
 
 	/*
-	 * Avoid races with device replace and make sure our bbio has devices
+	 * Avoid races with device replace and make sure our bioc has devices
 	 * associated to its stripes that don't go away while we are discarding.
 	 */
 	btrfs_bio_counter_inc_blocked(fs_info);
 	while (cur < end) {
-		struct btrfs_bio_stripe *stripe;
+		struct btrfs_io_stripe *stripe;
 		int i;
 
 		num_bytes = end - cur;
 		/* Tell the block device(s) that the sectors can be discarded */
 		ret = btrfs_map_block(fs_info, BTRFS_MAP_DISCARD, cur,
-				      &num_bytes, &bbio, 0);
+				      &num_bytes, &bioc, 0);
 		/*
 		 * Error can be -ENOMEM, -ENOENT (no such chunk mapping) or
 		 * -EOPNOTSUPP. For any such error, @num_bytes is not updated,
@@ -1337,8 +1342,8 @@
 		if (ret < 0)
 			goto out;
 
-		stripe = bbio->stripes;
-		for (i = 0; i < bbio->num_stripes; i++, stripe++) {
+		stripe = bioc->stripes;
+		for (i = 0; i < bioc->num_stripes; i++, stripe++) {
 			u64 bytes;
 			struct btrfs_device *device = stripe->dev;
 
@@ -1361,7 +1366,7 @@
 				 * And since there are two loops, explicitly
 				 * go to out to avoid confusion.
 				 */
-				btrfs_put_bbio(bbio);
+				btrfs_put_bioc(bioc);
 				goto out;
 			}
 
@@ -1372,7 +1377,7 @@
 			 */
 			ret = 0;
 		}
-		btrfs_put_bbio(bbio);
+		btrfs_put_bioc(bioc);
 		cur += num_bytes;
 	}
 out:
@@ -1670,12 +1675,12 @@
 		parent = ref->parent;
 	ref_root = ref->root;
 
-	if (node->ref_mod != 1) {
+	if (unlikely(node->ref_mod != 1)) {
 		btrfs_err(trans->fs_info,
-	"btree block(%llu) has %d references rather than 1: action %d ref_root %llu parent %llu",
+	"btree block %llu has %d references rather than 1: action %d ref_root %llu parent %llu",
 			  node->bytenr, node->ref_mod, node->action, ref_root,
 			  parent);
-		return -EIO;
+		return -EUCLEAN;
 	}
 	if (node->action == BTRFS_ADD_DELAYED_REF && insert_reserved) {
 		BUG_ON(!extent_op || !extent_op->update_flags);
@@ -1718,6 +1723,11 @@
 		BUG();
 	if (ret && insert_reserved)
 		btrfs_pin_extent(trans, node->bytenr, node->num_bytes, 1);
+	if (ret < 0)
+		btrfs_err(trans->fs_info,
+"failed to run delayed ref for logical %llu num_bytes %llu type %u action %u ref_mod %d: %d",
+			  node->bytenr, node->num_bytes, node->type,
+			  node->action, node->ref_mod, ret);
 	return ret;
 }
 
@@ -1956,8 +1966,6 @@
 		if (ret) {
 			unselect_delayed_ref_head(delayed_refs, locked_ref);
 			btrfs_put_delayed_ref(ref);
-			btrfs_debug(fs_info, "run_one_delayed_ref returned %d",
-				    ret);
 			return ret;
 		}
 
@@ -2376,7 +2384,7 @@
 
 out:
 	btrfs_free_path(path);
-	if (root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID)
+	if (btrfs_is_data_reloc_root(root))
 		WARN_ON(ret > 0);
 	return ret;
 }
@@ -2440,7 +2448,8 @@
 					       num_bytes, parent);
 			generic_ref.real_root = root->root_key.objectid;
 			btrfs_init_data_ref(&generic_ref, ref_root, key.objectid,
-					    key.offset);
+					    key.offset, root->root_key.objectid,
+					    for_reloc);
 			generic_ref.skip_qgroup = for_reloc;
 			if (inc)
 				ret = btrfs_inc_extent_ref(trans, &generic_ref);
@@ -2454,7 +2463,8 @@
 			btrfs_init_generic_ref(&generic_ref, action, bytenr,
 					       num_bytes, parent);
 			generic_ref.real_root = root->root_key.objectid;
-			btrfs_init_tree_ref(&generic_ref, level - 1, ref_root);
+			btrfs_init_tree_ref(&generic_ref, level - 1, ref_root,
+					    root->root_key.objectid, for_reloc);
 			generic_ref.skip_qgroup = for_reloc;
 			if (inc)
 				ret = btrfs_inc_extent_ref(trans, &generic_ref);
@@ -2571,17 +2581,10 @@
 		return -EINVAL;
 
 	/*
-	 * pull in the free space cache (if any) so that our pin
-	 * removes the free space from the cache.  We have load_only set
-	 * to one because the slow code to read in the free extents does check
-	 * the pinned extents.
+	 * Fully cache the free space first so that our pin removes the free space
+	 * from the cache.
 	 */
-	btrfs_cache_block_group(cache, 1);
-	/*
-	 * Make sure we wait until the cache is completely built in case it is
-	 * missing or is invalid and therefore needs to be rebuilt.
-	 */
-	ret = btrfs_wait_block_group_cache_done(cache);
+	ret = btrfs_cache_block_group(cache, true);
 	if (ret)
 		goto out;
 
@@ -2604,12 +2607,7 @@
 	if (!block_group)
 		return -EINVAL;
 
-	btrfs_cache_block_group(block_group, 1);
-	/*
-	 * Make sure we wait until the cache is completely built in case it is
-	 * missing or is invalid and therefore needs to be rebuilt.
-	 */
-	ret = btrfs_wait_block_group_cache_done(block_group);
+	ret = btrfs_cache_block_group(block_group, true);
 	if (ret)
 		goto out;
 
@@ -3278,20 +3276,20 @@
 }
 
 void btrfs_free_tree_block(struct btrfs_trans_handle *trans,
-			   struct btrfs_root *root,
+			   u64 root_id,
 			   struct extent_buffer *buf,
 			   u64 parent, int last_ref)
 {
-	struct btrfs_fs_info *fs_info = root->fs_info;
+	struct btrfs_fs_info *fs_info = trans->fs_info;
 	struct btrfs_ref generic_ref = { 0 };
 	int ret;
 
 	btrfs_init_generic_ref(&generic_ref, BTRFS_DROP_DELAYED_REF,
 			       buf->start, buf->len, parent);
 	btrfs_init_tree_ref(&generic_ref, btrfs_header_level(buf),
-			    root->root_key.objectid);
+			    root_id, 0, false);
 
-	if (root->root_key.objectid != BTRFS_TREE_LOG_OBJECTID) {
+	if (root_id != BTRFS_TREE_LOG_OBJECTID) {
 		btrfs_ref_tree_mod(fs_info, &generic_ref);
 		ret = btrfs_add_delayed_tree_ref(trans, &generic_ref, NULL);
 		BUG_ON(ret); /* -ENOMEM */
@@ -3301,7 +3299,7 @@
 		struct btrfs_block_group *cache;
 		bool must_pin = false;
 
-		if (root->root_key.objectid != BTRFS_TREE_LOG_OBJECTID) {
+		if (root_id != BTRFS_TREE_LOG_OBJECTID) {
 			ret = check_ref_cleanup(trans, buf->start);
 			if (!ret) {
 				btrfs_redirty_list_add(trans->transaction, buf);
@@ -3318,21 +3316,22 @@
 		}
 
 		/*
-		 * If this is a leaf and there are tree mod log users, we may
-		 * have recorded mod log operations that point to this leaf.
-		 * So we must make sure no one reuses this leaf's extent before
-		 * mod log operations are applied to a node, otherwise after
-		 * rewinding a node using the mod log operations we get an
-		 * inconsistent btree, as the leaf's extent may now be used as
-		 * a node or leaf for another different btree.
+		 * If there are tree mod log users we may have recorded mod log
+		 * operations for this node.  If we re-allocate this node we
+		 * could replay operations on this node that happened when it
+		 * existed in a completely different root.  For example if it
+		 * was part of root A, then was reallocated to root B, and we
+		 * are doing a btrfs_old_search_slot(root b), we could replay
+		 * operations that happened when the block was part of root A,
+		 * giving us an inconsistent view of the btree.
+		 *
 		 * We are safe from races here because at this point no other
 		 * node or root points to this extent buffer, so if after this
-		 * check a new tree mod log user joins, it will not be able to
-		 * find a node pointing to this leaf and record operations that
-		 * point to this leaf.
+		 * check a new tree mod log user joins we will not have an
+		 * existing log of operations on this node that we have to
+		 * contend with.
 		 */
-		if (btrfs_header_level(buf) == 0 &&
-		    test_bit(BTRFS_FS_TREE_MOD_LOG_USERS, &fs_info->flags))
+		if (test_bit(BTRFS_FS_TREE_MOD_LOG_USERS, &fs_info->flags))
 			must_pin = true;
 
 		if (must_pin || btrfs_is_zoned(fs_info)) {
@@ -3495,6 +3494,9 @@
 	/* Allocation is called for tree-log */
 	bool for_treelog;
 
+	/* Allocation is called for data relocation */
+	bool for_data_reloc;
+
 	/* RAID index, converted from flags */
 	int index;
 
@@ -3756,6 +3758,7 @@
 	u64 avail;
 	u64 bytenr = block_group->start;
 	u64 log_bytenr;
+	u64 data_reloc_bytenr;
 	int ret = 0;
 	bool skip;
 
@@ -3773,15 +3776,33 @@
 	if (skip)
 		return 1;
 
+	/*
+	 * Do not allow non-relocation blocks in the dedicated relocation block
+	 * group, and vice versa.
+	 */
+	spin_lock(&fs_info->relocation_bg_lock);
+	data_reloc_bytenr = fs_info->data_reloc_bg;
+	if (data_reloc_bytenr &&
+	    ((ffe_ctl->for_data_reloc && bytenr != data_reloc_bytenr) ||
+	     (!ffe_ctl->for_data_reloc && bytenr == data_reloc_bytenr)))
+		skip = true;
+	spin_unlock(&fs_info->relocation_bg_lock);
+	if (skip)
+		return 1;
+
 	spin_lock(&space_info->lock);
 	spin_lock(&block_group->lock);
 	spin_lock(&fs_info->treelog_bg_lock);
+	spin_lock(&fs_info->relocation_bg_lock);
 
 	ASSERT(!ffe_ctl->for_treelog ||
 	       block_group->start == fs_info->treelog_bg ||
 	       fs_info->treelog_bg == 0);
+	ASSERT(!ffe_ctl->for_data_reloc ||
+	       block_group->start == fs_info->data_reloc_bg ||
+	       fs_info->data_reloc_bg == 0);
 
-	if (block_group->ro) {
+	if (block_group->ro || block_group->zoned_data_reloc_ongoing) {
 		ret = 1;
 		goto out;
 	}
@@ -3796,6 +3817,16 @@
 		goto out;
 	}
 
+	/*
+	 * Do not allow currently used block group to be the data relocation
+	 * dedicated block group.
+	 */
+	if (ffe_ctl->for_data_reloc && !fs_info->data_reloc_bg &&
+	    (block_group->used || block_group->reserved)) {
+		ret = 1;
+		goto out;
+	}
+
 	avail = block_group->length - block_group->alloc_offset;
 	if (avail < num_bytes) {
 		if (ffe_ctl->max_extent_size < avail) {
@@ -3813,6 +3844,9 @@
 	if (ffe_ctl->for_treelog && !fs_info->treelog_bg)
 		fs_info->treelog_bg = block_group->start;
 
+	if (ffe_ctl->for_data_reloc && !fs_info->data_reloc_bg)
+		fs_info->data_reloc_bg = block_group->start;
+
 	ffe_ctl->found_offset = start + block_group->alloc_offset;
 	block_group->alloc_offset += num_bytes;
 	spin_lock(&ctl->tree_lock);
@@ -3829,6 +3863,25 @@
 out:
 	if (ret && ffe_ctl->for_treelog)
 		fs_info->treelog_bg = 0;
+	if (ret && ffe_ctl->for_data_reloc &&
+	    fs_info->data_reloc_bg == block_group->start) {
+		/*
+		 * Do not allow further allocations from this block group.
+		 * Compared to increasing the ->ro, setting the
+		 * ->zoned_data_reloc_ongoing flag still allows nocow
+		 *  writers to come in. See btrfs_inc_nocow_writers().
+		 *
+		 * We need to disable an allocation to avoid an allocation of
+		 * regular (non-relocation data) extent. With mix of relocation
+		 * extents and regular extents, we can dispatch WRITE commands
+		 * (for relocation extents) and ZONE APPEND commands (for
+		 * regular extents) at the same time to the same zone, which
+		 * easily break the write pointer.
+		 */
+		block_group->zoned_data_reloc_ongoing = 1;
+		fs_info->data_reloc_bg = 0;
+	}
+	spin_unlock(&fs_info->relocation_bg_lock);
 	spin_unlock(&fs_info->treelog_bg_lock);
 	spin_unlock(&block_group->lock);
 	spin_unlock(&space_info->lock);
@@ -4085,6 +4138,12 @@
 				ffe_ctl->hint_byte = fs_info->treelog_bg;
 			spin_unlock(&fs_info->treelog_bg_lock);
 		}
+		if (ffe_ctl->for_data_reloc) {
+			spin_lock(&fs_info->relocation_bg_lock);
+			if (fs_info->data_reloc_bg)
+				ffe_ctl->hint_byte = fs_info->data_reloc_bg;
+			spin_unlock(&fs_info->relocation_bg_lock);
+		}
 		return 0;
 	default:
 		BUG();
@@ -4129,6 +4188,8 @@
 	struct btrfs_space_info *space_info;
 	bool full_search = false;
 	bool for_treelog = (root->root_key.objectid == BTRFS_TREE_LOG_OBJECTID);
+	bool for_data_reloc = (btrfs_is_data_reloc_root(root) &&
+				       flags & BTRFS_BLOCK_GROUP_DATA);
 
 	WARN_ON(num_bytes < fs_info->sectorsize);
 
@@ -4143,6 +4204,7 @@
 	ffe_ctl.found_offset = 0;
 	ffe_ctl.hint_byte = hint_byte_orig;
 	ffe_ctl.for_treelog = for_treelog;
+	ffe_ctl.for_data_reloc = for_data_reloc;
 	ffe_ctl.policy = BTRFS_EXTENT_ALLOC_CLUSTERED;
 
 	/* For clustered allocation */
@@ -4220,6 +4282,8 @@
 		if (unlikely(block_group->ro)) {
 			if (for_treelog)
 				btrfs_clear_treelog_bg(block_group);
+			if (ffe_ctl.for_data_reloc)
+				btrfs_clear_data_reloc_bg(block_group);
 			continue;
 		}
 
@@ -4258,7 +4322,7 @@
 		ffe_ctl.cached = btrfs_block_group_done(block_group);
 		if (unlikely(!ffe_ctl.cached)) {
 			ffe_ctl.have_caching_bg = true;
-			ret = btrfs_cache_block_group(block_group, 0);
+			ret = btrfs_cache_block_group(block_group, false);
 
 			/*
 			 * If we get ENOMEM here or something else we want to
@@ -4276,8 +4340,11 @@
 			ret = 0;
 		}
 
-		if (unlikely(block_group->cached == BTRFS_CACHE_ERROR))
+		if (unlikely(block_group->cached == BTRFS_CACHE_ERROR)) {
+			if (!cache_block_group_error)
+				cache_block_group_error = -EIO;
 			goto loop;
+		}
 
 		bg_ret = NULL;
 		ret = do_allocation(block_group, &ffe_ctl, &bg_ret);
@@ -4408,6 +4475,7 @@
 	u64 flags;
 	int ret;
 	bool for_treelog = (root->root_key.objectid == BTRFS_TREE_LOG_OBJECTID);
+	bool for_data_reloc = (btrfs_is_data_reloc_root(root) && is_data);
 
 	flags = get_alloc_profile_by_root(root, is_data);
 again:
@@ -4431,8 +4499,8 @@
 
 			sinfo = btrfs_find_space_info(fs_info, flags);
 			btrfs_err(fs_info,
-			"allocation failed flags %llu, wanted %llu tree-log %d",
-				  flags, num_bytes, for_treelog);
+	"allocation failed flags %llu, wanted %llu tree-log %d, relocation: %d",
+				  flags, num_bytes, for_treelog, for_data_reloc);
 			if (sinfo)
 				btrfs_dump_space_info(fs_info, sinfo,
 						      num_bytes, 1);
@@ -4655,7 +4723,8 @@
 
 	btrfs_init_generic_ref(&generic_ref, BTRFS_ADD_DELAYED_EXTENT,
 			       ins->objectid, ins->offset, 0);
-	btrfs_init_data_ref(&generic_ref, root->root_key.objectid, owner, offset);
+	btrfs_init_data_ref(&generic_ref, root->root_key.objectid, owner,
+			    offset, 0, false);
 	btrfs_ref_tree_mod(root->fs_info, &generic_ref);
 
 	return btrfs_add_delayed_data_ref(trans, &generic_ref, ram_bytes);
@@ -4713,6 +4782,7 @@
 {
 	struct btrfs_fs_info *fs_info = root->fs_info;
 	struct extent_buffer *buf;
+	u64 lockdep_owner = owner;
 
 	buf = btrfs_find_create_tree_block(fs_info, bytenr, owner, level);
 	if (IS_ERR(buf))
@@ -4732,11 +4802,29 @@
 	}
 
 	/*
+	 * The reloc trees are just snapshots, so we need them to appear to be
+	 * just like any other fs tree WRT lockdep.
+	 *
+	 * The exception however is in replace_path() in relocation, where we
+	 * hold the lock on the original fs root and then search for the reloc
+	 * root.  At that point we need to make sure any reloc root buffers are
+	 * set to the BTRFS_TREE_RELOC_OBJECTID lockdep class in order to make
+	 * lockdep happy.
+	 */
+	if (lockdep_owner == BTRFS_TREE_RELOC_OBJECTID &&
+	    !test_bit(BTRFS_ROOT_RESET_LOCKDEP_CLASS, &root->state))
+		lockdep_owner = BTRFS_FS_TREE_OBJECTID;
+
+	/* btrfs_clean_tree_block() accesses generation field. */
+	btrfs_set_header_generation(buf, trans->transid);
+
+	/*
 	 * This needs to stay, because we could allocate a freed block from an
 	 * old tree into a new tree, so we need to make sure this new block is
 	 * set to the appropriate level and owner.
 	 */
-	btrfs_set_buffer_lockdep_class(owner, buf, level);
+	btrfs_set_buffer_lockdep_class(lockdep_owner, buf, level);
+
 	__btrfs_tree_lock(buf, nest);
 	btrfs_clean_tree_block(buf);
 	clear_bit(EXTENT_BUFFER_STALE, &buf->bflags);
@@ -4848,7 +4936,8 @@
 		btrfs_init_generic_ref(&generic_ref, BTRFS_ADD_DELAYED_EXTENT,
 				       ins.objectid, ins.offset, parent);
 		generic_ref.real_root = root->root_key.objectid;
-		btrfs_init_tree_ref(&generic_ref, level, root_objectid);
+		btrfs_init_tree_ref(&generic_ref, level, root_objectid,
+				    root->root_key.objectid, false);
 		btrfs_ref_tree_mod(fs_info, &generic_ref);
 		ret = btrfs_add_delayed_tree_ref(trans, &generic_ref, extent_op);
 		if (ret)
@@ -4938,7 +5027,15 @@
 		/* We don't care about errors in readahead. */
 		if (ret < 0)
 			continue;
-		BUG_ON(refs == 0);
+
+		/*
+		 * This could be racey, it's conceivable that we raced and end
+		 * up with a bogus refs count, if that's the case just skip, if
+		 * we are actually corrupt we will notice when we look up
+		 * everything again with our locks.
+		 */
+		if (refs == 0)
+			continue;
 
 		if (wc->stage == DROP_REFERENCE) {
 			if (refs == 1)
@@ -4997,15 +5094,18 @@
 	if (lookup_info &&
 	    ((wc->stage == DROP_REFERENCE && wc->refs[level] != 1) ||
 	     (wc->stage == UPDATE_BACKREF && !(wc->flags[level] & flag)))) {
-		BUG_ON(!path->locks[level]);
+		ASSERT(path->locks[level]);
 		ret = btrfs_lookup_extent_info(trans, fs_info,
 					       eb->start, level, 1,
 					       &wc->refs[level],
 					       &wc->flags[level]);
-		BUG_ON(ret == -ENOMEM);
 		if (ret)
 			return ret;
-		BUG_ON(wc->refs[level] == 0);
+		if (unlikely(wc->refs[level] == 0)) {
+			btrfs_err(fs_info, "bytenr %llu has 0 references, expect > 0",
+				  eb->start);
+			return -EUCLEAN;
+		}
 	}
 
 	if (wc->stage == DROP_REFERENCE) {
@@ -5021,7 +5121,7 @@
 
 	/* wc->stage == UPDATE_BACKREF */
 	if (!(wc->flags[level] & flag)) {
-		BUG_ON(!path->locks[level]);
+		ASSERT(path->locks[level]);
 		ret = btrfs_inc_ref(trans, root, eb, 1);
 		BUG_ON(ret); /* -ENOMEM */
 		ret = btrfs_dec_ref(trans, root, eb, 0);
@@ -5135,8 +5235,9 @@
 		goto out_unlock;
 
 	if (unlikely(wc->refs[level - 1] == 0)) {
-		btrfs_err(fs_info, "Missing references.");
-		ret = -EIO;
+		btrfs_err(fs_info, "bytenr %llu has 0 references, expect > 0",
+			  bytenr);
+		ret = -EUCLEAN;
 		goto out_unlock;
 	}
 	*lookup_info = 0;
@@ -5265,7 +5366,8 @@
 
 		btrfs_init_generic_ref(&ref, BTRFS_DROP_DELAYED_REF, bytenr,
 				       fs_info->nodesize, parent);
-		btrfs_init_tree_ref(&ref, level - 1, root->root_key.objectid);
+		btrfs_init_tree_ref(&ref, level - 1, root->root_key.objectid,
+				    0, false);
 		ret = btrfs_free_extent(trans, &ref);
 		if (ret)
 			goto out_unlock;
@@ -5336,7 +5438,12 @@
 				path->locks[level] = 0;
 				return ret;
 			}
-			BUG_ON(wc->refs[level] == 0);
+			if (unlikely(wc->refs[level] == 0)) {
+				btrfs_tree_unlock_rw(eb, path->locks[level]);
+				btrfs_err(fs_info, "bytenr %llu has 0 references, expect > 0",
+					  eb->start);
+				return -EUCLEAN;
+			}
 			if (wc->refs[level] == 1) {
 				btrfs_tree_unlock_rw(eb, path->locks[level]);
 				path->locks[level] = 0;
@@ -5354,7 +5461,10 @@
 				ret = btrfs_dec_ref(trans, root, eb, 1);
 			else
 				ret = btrfs_dec_ref(trans, root, eb, 0);
-			BUG_ON(ret); /* -ENOMEM */
+			if (ret) {
+				btrfs_abort_transaction(trans, ret);
+				return ret;
+			}
 			if (is_fstree(root->root_key.objectid)) {
 				ret = btrfs_qgroup_trace_leaf_items(trans, eb);
 				if (ret) {
@@ -5386,7 +5496,8 @@
 			goto owner_mismatch;
 	}
 
-	btrfs_free_tree_block(trans, root, eb, parent, wc->refs[level] == 1);
+	btrfs_free_tree_block(trans, btrfs_root_id(root), eb, parent,
+			      wc->refs[level] == 1);
 out:
 	wc->refs[level] = 0;
 	wc->flags[level] = 0;
@@ -5491,6 +5602,7 @@
 	int ret;
 	int level;
 	bool root_dropped = false;
+	bool unfinished_drop = false;
 
 	btrfs_debug(fs_info, "Drop subvolume %llu", root->root_key.objectid);
 
@@ -5533,6 +5645,8 @@
 	 * already dropped.
 	 */
 	set_bit(BTRFS_ROOT_DELETING, &root->state);
+	unfinished_drop = test_bit(BTRFS_ROOT_UNFINISHED_DROP, &root->state);
+
 	if (btrfs_disk_key_objectid(&root_item->drop_progress) == 0) {
 		level = btrfs_header_level(root->node);
 		path->nodes[level] = btrfs_lock_root_node(root);
@@ -5708,6 +5822,13 @@
 	btrfs_free_path(path);
 out:
 	/*
+	 * We were an unfinished drop root, check to see if there are any
+	 * pending, and if not clear and wake up any waiters.
+	 */
+	if (!err && unfinished_drop)
+		btrfs_maybe_wake_unfinished_drop(fs_info);
+
+	/*
 	 * So if we need to stop dropping the snapshot for whatever reason we
 	 * need to make sure to add it back to the dead root list so that we
 	 * keep trying to do the work later.  This also cleans up roots if we
@@ -5985,13 +6106,7 @@
 
 		if (end - start >= range->minlen) {
 			if (!btrfs_block_group_done(cache)) {
-				ret = btrfs_cache_block_group(cache, 0);
-				if (ret) {
-					bg_failed++;
-					bg_ret = ret;
-					continue;
-				}
-				ret = btrfs_wait_block_group_cache_done(cache);
+				ret = btrfs_cache_block_group(cache, true);
 				if (ret) {
 					bg_failed++;
 					bg_ret = ret;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/extent_io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/extent_io.c
@@ -1985,8 +1985,10 @@
 				    struct page *locked_page, u64 *start,
 				    u64 *end)
 {
+	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	struct extent_io_tree *tree = &BTRFS_I(inode)->io_tree;
-	u64 max_bytes = BTRFS_MAX_EXTENT_SIZE;
+	/* The sanity tests may not set a valid fs_info. */
+	u64 max_bytes = fs_info ? fs_info->max_extent_size : BTRFS_MAX_EXTENT_SIZE;
 	u64 delalloc_start;
 	u64 delalloc_end;
 	bool found;
@@ -2290,7 +2292,7 @@
 	struct btrfs_device *dev;
 	u64 map_length = 0;
 	u64 sector;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	int ret;
 
 	ASSERT(!(fs_info->sb->s_flags & SB_RDONLY));
@@ -2304,7 +2306,7 @@
 	map_length = length;
 
 	/*
-	 * Avoid races with device replace and make sure our bbio has devices
+	 * Avoid races with device replace and make sure our bioc has devices
 	 * associated to its stripes that don't go away while we are doing the
 	 * read repair operation.
 	 */
@@ -2317,28 +2319,28 @@
 		 * stripe's dev and sector.
 		 */
 		ret = btrfs_map_block(fs_info, BTRFS_MAP_READ, logical,
-				      &map_length, &bbio, 0);
+				      &map_length, &bioc, 0);
 		if (ret) {
 			btrfs_bio_counter_dec(fs_info);
 			bio_put(bio);
 			return -EIO;
 		}
-		ASSERT(bbio->mirror_num == 1);
+		ASSERT(bioc->mirror_num == 1);
 	} else {
 		ret = btrfs_map_block(fs_info, BTRFS_MAP_WRITE, logical,
-				      &map_length, &bbio, mirror_num);
+				      &map_length, &bioc, mirror_num);
 		if (ret) {
 			btrfs_bio_counter_dec(fs_info);
 			bio_put(bio);
 			return -EIO;
 		}
-		BUG_ON(mirror_num != bbio->mirror_num);
+		BUG_ON(mirror_num != bioc->mirror_num);
 	}
 
-	sector = bbio->stripes[bbio->mirror_num - 1].physical >> 9;
+	sector = bioc->stripes[bioc->mirror_num - 1].physical >> 9;
 	bio->bi_iter.bi_sector = sector;
-	dev = bbio->stripes[bbio->mirror_num - 1].dev;
-	btrfs_put_bbio(bbio);
+	dev = bioc->stripes[bioc->mirror_num - 1].dev;
+	btrfs_put_bioc(bioc);
 	if (!dev || !dev->bdev ||
 	    !test_bit(BTRFS_DEV_STATE_WRITEABLE, &dev->dev_state)) {
 		btrfs_bio_counter_dec(fs_info);
@@ -3327,7 +3329,7 @@
 	if (wbc) {
 		struct block_device *bdev;
 
-		bdev = fs_info->fs_devices->latest_bdev;
+		bdev = fs_info->fs_devices->latest_dev->bdev;
 		bio_set_dev(bio, bdev);
 		wbc_init_bio(wbc, bio);
 	}
@@ -3561,7 +3563,6 @@
 	u64 cur_end;
 	struct extent_map *em;
 	int ret = 0;
-	int nr = 0;
 	size_t pg_offset = 0;
 	size_t iosize;
 	size_t blocksize = inode->i_sb->s_blocksize;
@@ -3727,11 +3728,13 @@
 					 end_bio_extent_readpage, 0,
 					 this_bio_flag,
 					 force_bio_submit);
-		if (!ret) {
-			nr++;
-		} else {
-			unlock_extent(tree, cur, cur + iosize - 1);
-			end_page_read(page, false, cur, iosize);
+		if (ret) {
+			/*
+			 * We have to unlock the remaining range, or the page
+			 * will never be unlocked.
+			 */
+			unlock_extent(tree, cur, end);
+			end_page_read(page, false, cur, end + 1 - cur);
 			goto out;
 		}
 		cur = cur + iosize;
@@ -3777,10 +3780,11 @@
  */
 static noinline_for_stack int writepage_delalloc(struct btrfs_inode *inode,
 		struct page *page, struct writeback_control *wbc,
-		u64 delalloc_start, unsigned long *nr_written)
+		unsigned long *nr_written)
 {
-	u64 page_end = delalloc_start + PAGE_SIZE - 1;
+	u64 page_end = page_offset(page) + PAGE_SIZE - 1;
 	bool found;
+	u64 delalloc_start = page_offset(page);
 	u64 delalloc_to_write = 0;
 	u64 delalloc_end = 0;
 	int ret;
@@ -3905,10 +3909,12 @@
 	u64 extent_offset;
 	u64 block_start;
 	struct extent_map *em;
+	int saved_ret = 0;
 	int ret = 0;
 	int nr = 0;
 	u32 opf = REQ_OP_WRITE;
 	const unsigned int write_flags = wbc_to_write_flags(wbc);
+	bool has_error = false;
 	bool compressed;
 
 	ret = btrfs_writepage_cow_fixup(page);
@@ -3959,6 +3965,9 @@
 		if (IS_ERR_OR_NULL(em)) {
 			btrfs_page_set_error(fs_info, page, cur, end - cur + 1);
 			ret = PTR_ERR_OR_ZERO(em);
+			has_error = true;
+			if (!saved_ret)
+				saved_ret = ret;
 			break;
 		}
 
@@ -4022,6 +4031,10 @@
 					 end_bio_extent_writepage,
 					 0, 0, false);
 		if (ret) {
+			has_error = true;
+			if (!saved_ret)
+				saved_ret = ret;
+
 			btrfs_page_set_error(fs_info, page, cur, iosize);
 			if (PageWriteback(page))
 				btrfs_page_clear_writeback(fs_info, page, cur,
@@ -4035,8 +4048,10 @@
 	 * If we finish without problem, we should not only clear page dirty,
 	 * but also empty subpage dirty bits
 	 */
-	if (!ret)
+	if (!has_error)
 		btrfs_page_assert_not_dirty(fs_info, page);
+	else
+		ret = saved_ret;
 	*nr_ret = nr;
 	return ret;
 }
@@ -4054,8 +4069,8 @@
 			      struct extent_page_data *epd)
 {
 	struct inode *inode = page->mapping->host;
-	u64 start = page_offset(page);
-	u64 page_end = start + PAGE_SIZE - 1;
+	const u64 page_start = page_offset(page);
+	const u64 page_end = page_start + PAGE_SIZE - 1;
 	int ret;
 	int nr = 0;
 	size_t pg_offset;
@@ -4090,8 +4105,7 @@
 	}
 
 	if (!epd->extent_locked) {
-		ret = writepage_delalloc(BTRFS_I(inode), page, wbc, start,
-					 &nr_written);
+		ret = writepage_delalloc(BTRFS_I(inode), page, wbc, &nr_written);
 		if (ret == 1)
 			return 0;
 		if (ret)
@@ -4141,7 +4155,7 @@
 	 * capable of that.
 	 */
 	if (PageError(page))
-		end_extent_writepage(page, ret, start, page_end);
+		end_extent_writepage(page, ret, page_start, page_end);
 	unlock_page(page);
 	ASSERT(ret <= 0);
 	return ret;
@@ -4285,6 +4299,12 @@
 		return;
 
 	/*
+	 * A read may stumble upon this buffer later, make sure that it gets an
+	 * error and knows there was an error.
+	 */
+	clear_bit(EXTENT_BUFFER_UPTODATE, &eb->bflags);
+
+	/*
 	 * If we error out, we should add back the dirty_metadata_bytes
 	 * to make it consistent.
 	 */
@@ -4824,11 +4844,12 @@
 			}
 
 			/*
-			 * the filesystem may choose to bump up nr_to_write.
+			 * The filesystem may choose to bump up nr_to_write.
 			 * We have to make sure to honor the new nr_to_write
-			 * at any time
+			 * at any time.
 			 */
-			nr_to_write_done = wbc->nr_to_write <= 0;
+			nr_to_write_done = (wbc->sync_mode == WB_SYNC_NONE &&
+					    wbc->nr_to_write <= 0);
 		}
 		pagevec_release(&pvec);
 		cond_resched();
@@ -5120,6 +5141,7 @@
 int extent_writepages(struct address_space *mapping,
 		      struct writeback_control *wbc)
 {
+	struct inode *inode = mapping->host;
 	int ret = 0;
 	struct extent_page_data epd = {
 		.bio_ctrl = { 0 },
@@ -5127,13 +5149,20 @@
 		.sync_io = wbc->sync_mode == WB_SYNC_ALL,
 	};
 
+	/*
+	 * Allow only a single thread to do the reloc work in zoned mode to
+	 * protect the write pointer updates.
+	 */
+	btrfs_zoned_data_reloc_lock(BTRFS_I(inode));
 	ret = extent_write_cache_pages(mapping, wbc, &epd);
 	ASSERT(ret <= 0);
 	if (ret < 0) {
+		btrfs_zoned_data_reloc_unlock(BTRFS_I(inode));
 		end_write_bio(&epd, ret);
 		return ret;
 	}
 	ret = flush_write_bio(&epd);
+	btrfs_zoned_data_reloc_unlock(BTRFS_I(inode));
 	return ret;
 }
 
@@ -6081,6 +6110,7 @@
 	struct extent_buffer *exists = NULL;
 	struct page *p;
 	struct address_space *mapping = fs_info->btree_inode->i_mapping;
+	u64 lockdep_owner = owner_root;
 	int uptodate = 1;
 	int ret;
 
@@ -6115,7 +6145,15 @@
 	eb = __alloc_extent_buffer(fs_info, start, len);
 	if (!eb)
 		return ERR_PTR(-ENOMEM);
-	btrfs_set_buffer_lockdep_class(owner_root, eb, level);
+
+	/*
+	 * The reloc trees are just snapshots, so we need them to appear to be
+	 * just like any other fs tree WRT lockdep.
+	 */
+	if (lockdep_owner == BTRFS_TREE_RELOC_OBJECTID)
+		lockdep_owner = BTRFS_FS_TREE_OBJECTID;
+
+	btrfs_set_buffer_lockdep_class(lockdep_owner, eb, level);
 
 	num_pages = num_extent_pages(eb);
 	for (i = 0; i < num_pages; i++, index++) {
@@ -6530,6 +6568,14 @@
 	if (test_bit(EXTENT_BUFFER_UPTODATE, &eb->bflags))
 		return 0;
 
+	/*
+	 * We could have had EXTENT_BUFFER_UPTODATE cleared by the write
+	 * operation, which could potentially still be in flight.  In this case
+	 * we simply want to return an error.
+	 */
+	if (unlikely(test_bit(EXTENT_BUFFER_WRITE_ERR, &eb->bflags)))
+		return -EIO;
+
 	if (eb->fs_info->sectorsize < PAGE_SIZE)
 		return read_extent_buffer_subpage(eb, wait, mirror_num);
 
@@ -6676,8 +6722,14 @@
 	char *dst = (char *)dstv;
 	unsigned long i = get_eb_page_index(start);
 
-	if (check_eb_range(eb, start, len))
+	if (check_eb_range(eb, start, len)) {
+		/*
+		 * Invalid range hit, reset the memory, so callers won't get
+		 * some random garbage for their uninitialzed memory.
+		 */
+		memset(dstv, 0, len);
 		return;
+	}
 
 	offset = get_eb_offset_in_page(eb, start);
 
@@ -6776,14 +6828,24 @@
 {
 	struct btrfs_fs_info *fs_info = eb->fs_info;
 
+	/*
+	 * If we are using the commit root we could potentially clear a page
+	 * Uptodate while we're using the extent buffer that we've previously
+	 * looked up.  We don't want to complain in this case, as the page was
+	 * valid before, we just didn't write it out.  Instead we want to catch
+	 * the case where we didn't actually read the block properly, which
+	 * would have !PageUptodate && !PageError, as we clear PageError before
+	 * reading.
+	 */
 	if (fs_info->sectorsize < PAGE_SIZE) {
-		bool uptodate;
+		bool uptodate, error;
 
 		uptodate = btrfs_subpage_test_uptodate(fs_info, page,
 						       eb->start, eb->len);
-		WARN_ON(!uptodate);
+		error = btrfs_subpage_test_error(fs_info, page, eb->start, eb->len);
+		WARN_ON(!uptodate && !error);
 	} else {
-		WARN_ON(!PageUptodate(page));
+		WARN_ON(!PageUptodate(page) && !PageError(page));
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/extent_io.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/extent_io.h
@@ -117,7 +117,7 @@
  */
 struct extent_changeset {
 	/* How many bytes are set/cleared in this operation */
-	unsigned int bytes_changed;
+	u64 bytes_changed;
 
 	/* Changed ranges */
 	struct ulist range_changed;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/extent_map.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/extent_map.c
@@ -360,7 +360,7 @@
 	int i;
 
 	for (i = 0; i < map->num_stripes; i++) {
-		struct btrfs_bio_stripe *stripe = &map->stripes[i];
+		struct btrfs_io_stripe *stripe = &map->stripes[i];
 		struct btrfs_device *device = stripe->dev;
 
 		set_extent_bits_nowait(&device->alloc_state, stripe->physical,
@@ -375,7 +375,7 @@
 	int i;
 
 	for (i = 0; i < map->num_stripes; i++) {
-		struct btrfs_bio_stripe *stripe = &map->stripes[i];
+		struct btrfs_io_stripe *stripe = &map->stripes[i];
 		struct btrfs_device *device = stripe->dev;
 
 		__clear_extent_bit(&device->alloc_state, stripe->physical,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/file-item.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/file-item.c
@@ -47,13 +47,13 @@
 	u64 start, end, i_size;
 	int ret;
 
+	spin_lock(&inode->lock);
 	i_size = new_i_size ?: i_size_read(&inode->vfs_inode);
 	if (btrfs_fs_incompat(fs_info, NO_HOLES)) {
 		inode->disk_i_size = i_size;
-		return;
+		goto out_unlock;
 	}
 
-	spin_lock(&inode->lock);
 	ret = find_contiguous_extent_bit(&inode->file_extent_tree, 0, &start,
 					 &end, EXTENT_DIRTY);
 	if (!ret && start == 0)
@@ -61,6 +61,7 @@
 	else
 		i_size = 0;
 	inode->disk_i_size = i_size;
+out_unlock:
 	spin_unlock(&inode->lock);
 }
 
@@ -303,7 +304,7 @@
 	read_extent_buffer(path->nodes[0], dst, (unsigned long)item,
 			ret * csum_size);
 out:
-	if (ret == -ENOENT)
+	if (ret == -ENOENT || ret == -EFBIG)
 		ret = 0;
 	return ret;
 }
@@ -699,7 +700,9 @@
 				sums = kvzalloc(btrfs_ordered_sum_size(fs_info,
 						      bytes_left), GFP_KERNEL);
 				memalloc_nofs_restore(nofs_flag);
-				BUG_ON(!sums); /* -ENOMEM */
+				if (!sums)
+					return BLK_STS_RESOURCE;
+
 				sums->len = bytes_left;
 				ordered = btrfs_lookup_ordered_extent(inode,
 								offset);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/file.c
@@ -731,7 +731,7 @@
 	if (args->drop_cache)
 		btrfs_drop_extent_cache(inode, args->start, args->end - 1, 0);
 
-	if (args->start >= inode->disk_i_size && !args->replace_extent)
+	if (data_race(args->start >= inode->disk_i_size) && !args->replace_extent)
 		modify_tree = 0;
 
 	update_refs = (root->root_key.objectid != BTRFS_TREE_LOG_OBJECTID);
@@ -869,9 +869,13 @@
 				btrfs_init_data_ref(&ref,
 						root->root_key.objectid,
 						new_key.objectid,
-						args->start - extent_offset);
+						args->start - extent_offset,
+						0, false);
 				ret = btrfs_inc_extent_ref(trans, &ref);
-				BUG_ON(ret); /* -ENOMEM */
+				if (ret) {
+					btrfs_abort_transaction(trans, ret);
+					break;
+				}
 			}
 			key.offset = args->start;
 		}
@@ -955,9 +959,13 @@
 				btrfs_init_data_ref(&ref,
 						root->root_key.objectid,
 						key.objectid,
-						key.offset - extent_offset);
+						key.offset - extent_offset, 0,
+						false);
 				ret = btrfs_free_extent(trans, &ref);
-				BUG_ON(ret); /* -ENOMEM */
+				if (ret) {
+					btrfs_abort_transaction(trans, ret);
+					break;
+				}
 				args->bytes_found += extent_end - key.offset;
 			}
 
@@ -1232,7 +1240,7 @@
 		btrfs_init_generic_ref(&ref, BTRFS_ADD_DELAYED_REF, bytenr,
 				       num_bytes, 0);
 		btrfs_init_data_ref(&ref, root->root_key.objectid, ino,
-				    orig_offset);
+				    orig_offset, 0, false);
 		ret = btrfs_inc_extent_ref(trans, &ref);
 		if (ret) {
 			btrfs_abort_transaction(trans, ret);
@@ -1257,7 +1265,8 @@
 	other_end = 0;
 	btrfs_init_generic_ref(&ref, BTRFS_DROP_DELAYED_REF, bytenr,
 			       num_bytes, 0);
-	btrfs_init_data_ref(&ref, root->root_key.objectid, ino, orig_offset);
+	btrfs_init_data_ref(&ref, root->root_key.objectid, ino, orig_offset,
+			    0, false);
 	if (extent_mergeable(leaf, path->slots[0] + 1,
 			     ino, bytenr, orig_offset,
 			     &other_start, &other_end)) {
@@ -1598,7 +1607,6 @@
 	loff_t pos = iocb->ki_pos;
 	int ret;
 	loff_t oldsize;
-	loff_t start_pos;
 
 	if (iocb->ki_flags & IOCB_NOWAIT) {
 		size_t nocow_bytes = count;
@@ -1628,9 +1636,8 @@
 	 */
 	update_time_for_write(inode);
 
-	start_pos = round_down(pos, fs_info->sectorsize);
 	oldsize = i_size_read(inode);
-	if (start_pos > oldsize) {
+	if (pos > oldsize) {
 		/* Expand hole size to cover write data, preventing empty gap */
 		loff_t end_pos = round_up(pos + count, fs_info->sectorsize);
 
@@ -1709,7 +1716,7 @@
 		 * Fault pages before locking them in prepare_pages
 		 * to avoid recursive lock
 		 */
-		if (unlikely(iov_iter_fault_in_readable(i, write_bytes))) {
+		if (unlikely(fault_in_iov_iter_readable(i, write_bytes))) {
 			ret = -EFAULT;
 			break;
 		}
@@ -1909,10 +1916,11 @@
 	loff_t pos;
 	ssize_t written = 0;
 	ssize_t written_buffered;
+	size_t prev_left = 0;
 	loff_t endbyte;
 	ssize_t err;
 	unsigned int ilock_flags = 0;
-	struct iomap_dio *dio = NULL;
+	struct iomap_dio *dio;
 
 	if (iocb->ki_flags & IOCB_NOWAIT)
 		ilock_flags |= BTRFS_ILOCK_TRY;
@@ -1955,23 +1963,81 @@
 		goto buffered;
 	}
 
+	/*
+	 * The iov_iter can be mapped to the same file range we are writing to.
+	 * If that's the case, then we will deadlock in the iomap code, because
+	 * it first calls our callback btrfs_dio_iomap_begin(), which will create
+	 * an ordered extent, and after that it will fault in the pages that the
+	 * iov_iter refers to. During the fault in we end up in the readahead
+	 * pages code (starting at btrfs_readahead()), which will lock the range,
+	 * find that ordered extent and then wait for it to complete (at
+	 * btrfs_lock_and_flush_ordered_range()), resulting in a deadlock since
+	 * obviously the ordered extent can never complete as we didn't submit
+	 * yet the respective bio(s). This always happens when the buffer is
+	 * memory mapped to the same file range, since the iomap DIO code always
+	 * invalidates pages in the target file range (after starting and waiting
+	 * for any writeback).
+	 *
+	 * So here we disable page faults in the iov_iter and then retry if we
+	 * got -EFAULT, faulting in the pages before the retry.
+	 */
+again:
+	from->nofault = true;
 	dio = __iomap_dio_rw(iocb, from, &btrfs_dio_iomap_ops, &btrfs_dio_ops,
-			     0);
-
-	btrfs_inode_unlock(inode, ilock_flags);
+			     IOMAP_DIO_PARTIAL, written);
+	from->nofault = false;
 
 	if (IS_ERR_OR_NULL(dio)) {
 		err = PTR_ERR_OR_ZERO(dio);
-		if (err < 0 && err != -ENOTBLK)
-			goto out;
 	} else {
-		written = iomap_dio_complete(dio);
+		/*
+		 * If we have a synchoronous write, we must make sure the fsync
+		 * triggered by the iomap_dio_complete() call below doesn't
+		 * deadlock on the inode lock - we are already holding it and we
+		 * can't call it after unlocking because we may need to complete
+		 * partial writes due to the input buffer (or parts of it) not
+		 * being already faulted in.
+		 */
+		ASSERT(current->journal_info == NULL);
+		current->journal_info = BTRFS_TRANS_DIO_WRITE_STUB;
+		err = iomap_dio_complete(dio);
+		current->journal_info = NULL;
+	}
+
+	/* No increment (+=) because iomap returns a cumulative value. */
+	if (err > 0)
+		written = err;
+
+	if (iov_iter_count(from) > 0 && (err == -EFAULT || err > 0)) {
+		const size_t left = iov_iter_count(from);
+		/*
+		 * We have more data left to write. Try to fault in as many as
+		 * possible of the remainder pages and retry. We do this without
+		 * releasing and locking again the inode, to prevent races with
+		 * truncate.
+		 *
+		 * Also, in case the iov refers to pages in the file range of the
+		 * file we want to write to (due to a mmap), we could enter an
+		 * infinite loop if we retry after faulting the pages in, since
+		 * iomap will invalidate any pages in the range early on, before
+		 * it tries to fault in the pages of the iov. So we keep track of
+		 * how much was left of iov in the previous EFAULT and fallback
+		 * to buffered IO in case we haven't made any progress.
+		 */
+		if (left == prev_left) {
+			err = -ENOTBLK;
+		} else {
+			fault_in_iov_iter_readable(from, left);
+			prev_left = left;
+			goto again;
+		}
 	}
 
-	if (written < 0 || !iov_iter_count(from)) {
-		err = written;
+	btrfs_inode_unlock(inode, ilock_flags);
+
+	/* If 'err' is -ENOTBLK then it means we must fallback to buffered IO. */
+	if ((err < 0 && err != -ENOTBLK) || !iov_iter_count(from))
 		goto out;
-	}
 
 buffered:
 	pos = iocb->ki_pos;
@@ -1996,7 +2062,7 @@
 	invalidate_mapping_pages(file->f_mapping, pos >> PAGE_SHIFT,
 				 endbyte >> PAGE_SHIFT);
 out:
-	return written ? written : err;
+	return err < 0 ? err : written;
 }
 
 static ssize_t btrfs_file_write_iter(struct kiocb *iocb,
@@ -2126,6 +2192,13 @@
 	int ret = 0, err;
 	u64 len;
 	bool full_sync;
+	bool skip_ilock = false;
+
+	if (current->journal_info == BTRFS_TRANS_DIO_WRITE_STUB) {
+		skip_ilock = true;
+		current->journal_info = NULL;
+		lockdep_assert_held(&inode->i_rwsem);
+	}
 
 	trace_btrfs_sync_file(file, datasync);
 
@@ -2153,7 +2226,10 @@
 	if (ret)
 		goto out;
 
-	btrfs_inode_lock(inode, BTRFS_ILOCK_MMAP);
+	if (skip_ilock)
+		down_write(&BTRFS_I(inode)->i_mmap_lock);
+	else
+		btrfs_inode_lock(inode, BTRFS_ILOCK_MMAP);
 
 	atomic_inc(&root->log_batch);
 
@@ -2185,7 +2261,10 @@
 	 */
 	ret = start_ordered_ops(inode, start, end);
 	if (ret) {
-		btrfs_inode_unlock(inode, BTRFS_ILOCK_MMAP);
+		if (skip_ilock)
+			up_write(&BTRFS_I(inode)->i_mmap_lock);
+		else
+			btrfs_inode_unlock(inode, BTRFS_ILOCK_MMAP);
 		goto out;
 	}
 
@@ -2277,27 +2356,67 @@
 	 * file again, but that will end up using the synchronization
 	 * inside btrfs_sync_log to keep things safe.
 	 */
-	btrfs_inode_unlock(inode, BTRFS_ILOCK_MMAP);
+	if (skip_ilock)
+		up_write(&BTRFS_I(inode)->i_mmap_lock);
+	else
+		btrfs_inode_unlock(inode, BTRFS_ILOCK_MMAP);
 
-	if (ret != BTRFS_NO_LOG_SYNC) {
+	if (ret == BTRFS_NO_LOG_SYNC) {
+		ret = btrfs_end_transaction(trans);
+		goto out;
+	}
+
+	/* We successfully logged the inode, attempt to sync the log. */
+	if (!ret) {
+		ret = btrfs_sync_log(trans, root, &ctx);
 		if (!ret) {
-			ret = btrfs_sync_log(trans, root, &ctx);
-			if (!ret) {
-				ret = btrfs_end_transaction(trans);
-				goto out;
-			}
-		}
-		if (!full_sync) {
-			ret = btrfs_wait_ordered_range(inode, start, len);
-			if (ret) {
-				btrfs_end_transaction(trans);
-				goto out;
-			}
+			ret = btrfs_end_transaction(trans);
+			goto out;
 		}
-		ret = btrfs_commit_transaction(trans);
-	} else {
+	}
+
+	/*
+	 * At this point we need to commit the transaction because we had
+	 * btrfs_need_log_full_commit() or some other error.
+	 *
+	 * If we didn't do a full sync we have to stop the trans handle, wait on
+	 * the ordered extents, start it again and commit the transaction.  If
+	 * we attempt to wait on the ordered extents here we could deadlock with
+	 * something like fallocate() that is holding the extent lock trying to
+	 * start a transaction while some other thread is trying to commit the
+	 * transaction while we (fsync) are currently holding the transaction
+	 * open.
+	 */
+	if (!full_sync) {
 		ret = btrfs_end_transaction(trans);
+		if (ret)
+			goto out;
+		ret = btrfs_wait_ordered_range(inode, start, len);
+		if (ret)
+			goto out;
+
+		/*
+		 * This is safe to use here because we're only interested in
+		 * making sure the transaction that had the ordered extents is
+		 * committed.  We aren't waiting on anything past this point,
+		 * we're purely getting the transaction and committing it.
+		 */
+		trans = btrfs_attach_transaction_barrier(root);
+		if (IS_ERR(trans)) {
+			ret = PTR_ERR(trans);
+
+			/*
+			 * We committed the transaction and there's no currently
+			 * running transaction, this means everything we care
+			 * about made it to disk and we are done.
+			 */
+			if (ret == -ENOENT)
+				ret = 0;
+			goto out;
+		}
 	}
+
+	ret = btrfs_commit_transaction(trans);
 out:
 	ASSERT(list_empty(&ctx.list));
 	err = file_check_and_advance_wb_err(file);
@@ -2307,7 +2426,10 @@
 
 out_release_extents:
 	btrfs_release_log_ctx_extents(&ctx);
-	btrfs_inode_unlock(inode, BTRFS_ILOCK_MMAP);
+	if (skip_ilock)
+		up_write(&BTRFS_I(inode)->i_mmap_lock);
+	else
+		btrfs_inode_unlock(inode, BTRFS_ILOCK_MMAP);
 	goto out;
 }
 
@@ -2620,7 +2742,7 @@
 				       extent_info->disk_len, 0);
 		ref_offset = extent_info->file_offset - extent_info->data_offset;
 		btrfs_init_data_ref(&ref, root->root_key.objectid,
-				    btrfs_ino(inode), ref_offset);
+				    btrfs_ino(inode), ref_offset, 0, false);
 		ret = btrfs_inc_extent_ref(trans, &ref);
 	}
 
@@ -2878,8 +3000,9 @@
 	return ret;
 }
 
-static int btrfs_punch_hole(struct inode *inode, loff_t offset, loff_t len)
+static int btrfs_punch_hole(struct file *file, loff_t offset, loff_t len)
 {
+	struct inode *inode = file_inode(file);
 	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	struct btrfs_root *root = BTRFS_I(inode)->root;
 	struct extent_state *cached_state = NULL;
@@ -2911,6 +3034,10 @@
 		goto out_only_mutex;
 	}
 
+	ret = file_modified(file);
+	if (ret)
+		goto out_only_mutex;
+
 	lockstart = round_up(offset, btrfs_inode_sectorsize(BTRFS_I(inode)));
 	lockend = round_down(offset + len,
 			     btrfs_inode_sectorsize(BTRFS_I(inode))) - 1;
@@ -3351,7 +3478,7 @@
 		return -EOPNOTSUPP;
 
 	if (mode & FALLOC_FL_PUNCH_HOLE)
-		return btrfs_punch_hole(inode, offset, len);
+		return btrfs_punch_hole(file, offset, len);
 
 	/*
 	 * Only trigger disk allocation, don't trigger qgroup reserve
@@ -3373,6 +3500,10 @@
 			goto out;
 	}
 
+	ret = file_modified(file);
+	if (ret)
+		goto out;
+
 	/*
 	 * TODO: Move these two operations after we have checked
 	 * accurate reserved space, or fallocate can still fail but
@@ -3650,6 +3781,8 @@
 static ssize_t btrfs_direct_read(struct kiocb *iocb, struct iov_iter *to)
 {
 	struct inode *inode = file_inode(iocb->ki_filp);
+	size_t prev_left = 0;
+	ssize_t read = 0;
 	ssize_t ret;
 
 	if (fsverity_active(inode))
@@ -3659,9 +3792,57 @@
 		return 0;
 
 	btrfs_inode_lock(inode, BTRFS_ILOCK_SHARED);
-	ret = iomap_dio_rw(iocb, to, &btrfs_dio_iomap_ops, &btrfs_dio_ops, 0);
+again:
+	/*
+	 * This is similar to what we do for direct IO writes, see the comment
+	 * at btrfs_direct_write(), but we also disable page faults in addition
+	 * to disabling them only at the iov_iter level. This is because when
+	 * reading from a hole or prealloc extent, iomap calls iov_iter_zero(),
+	 * which can still trigger page fault ins despite having set ->nofault
+	 * to true of our 'to' iov_iter.
+	 *
+	 * The difference to direct IO writes is that we deadlock when trying
+	 * to lock the extent range in the inode's tree during he page reads
+	 * triggered by the fault in (while for writes it is due to waiting for
+	 * our own ordered extent). This is because for direct IO reads,
+	 * btrfs_dio_iomap_begin() returns with the extent range locked, which
+	 * is only unlocked in the endio callback (end_bio_extent_readpage()).
+	 */
+	pagefault_disable();
+	to->nofault = true;
+	ret = iomap_dio_rw(iocb, to, &btrfs_dio_iomap_ops, &btrfs_dio_ops,
+			   IOMAP_DIO_PARTIAL, read);
+	to->nofault = false;
+	pagefault_enable();
+
+	/* No increment (+=) because iomap returns a cumulative value. */
+	if (ret > 0)
+		read = ret;
+
+	if (iov_iter_count(to) > 0 && (ret == -EFAULT || ret > 0)) {
+		const size_t left = iov_iter_count(to);
+
+		if (left == prev_left) {
+			/*
+			 * We didn't make any progress since the last attempt,
+			 * fallback to a buffered read for the remainder of the
+			 * range. This is just to avoid any possibility of looping
+			 * for too long.
+			 */
+			ret = read;
+		} else {
+			/*
+			 * We made some progress since the last retry or this is
+			 * the first time we are retrying. Fault in as many pages
+			 * as possible and retry.
+			 */
+			fault_in_iov_iter_writeable(to, left);
+			prev_left = left;
+			goto again;
+		}
+	}
 	btrfs_inode_unlock(inode, BTRFS_ILOCK_SHARED);
-	return ret;
+	return ret < 0 ? ret : read;
 }
 
 static ssize_t btrfs_file_read_iter(struct kiocb *iocb, struct iov_iter *to)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/free-space-cache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/free-space-cache.c
@@ -672,6 +672,12 @@
 
 	max_bitmaps = max_t(u64, max_bitmaps, 1);
 
+	if (ctl->total_bitmaps > max_bitmaps)
+		btrfs_err(block_group->fs_info,
+"invalid free space control: bg start=%llu len=%llu total_bitmaps=%u unit=%u max_bitmaps=%llu bytes_per_bg=%llu",
+			  block_group->start, block_group->length,
+			  ctl->total_bitmaps, ctl->unit, max_bitmaps,
+			  bytes_per_bg);
 	ASSERT(ctl->total_bitmaps <= max_bitmaps);
 
 	/*
@@ -819,15 +825,17 @@
 			}
 			spin_lock(&ctl->tree_lock);
 			ret = link_free_space(ctl, e);
-			ctl->total_bitmaps++;
-			recalculate_thresholds(ctl);
-			spin_unlock(&ctl->tree_lock);
 			if (ret) {
+				spin_unlock(&ctl->tree_lock);
 				btrfs_err(fs_info,
 					"Duplicate entries in free space cache, dumping");
+				kmem_cache_free(btrfs_free_space_bitmap_cachep, e->bitmap);
 				kmem_cache_free(btrfs_free_space_cachep, e);
 				goto free_cache;
 			}
+			ctl->total_bitmaps++;
+			recalculate_thresholds(ctl);
+			spin_unlock(&ctl->tree_lock);
 			list_add_tail(&e->list, &bitmaps);
 		}
 
@@ -1779,9 +1787,9 @@
 	ctl->free_space -= bytes;
 }
 
-static void bitmap_set_bits(struct btrfs_free_space_ctl *ctl,
-			    struct btrfs_free_space *info, u64 offset,
-			    u64 bytes)
+static void btrfs_bitmap_set_bits(struct btrfs_free_space_ctl *ctl,
+				  struct btrfs_free_space *info, u64 offset,
+				  u64 bytes)
 {
 	unsigned long start, count, end;
 	int extent_delta = 1;
@@ -2077,7 +2085,7 @@
 
 	bytes_to_set = min(end - offset, bytes);
 
-	bitmap_set_bits(ctl, info, offset, bytes_to_set);
+	btrfs_bitmap_set_bits(ctl, info, offset, bytes_to_set);
 
 	/*
 	 * We set some bytes, we have no idea what the max extent size is
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/free-space-tree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/free-space-tree.c
@@ -1256,8 +1256,8 @@
 	btrfs_tree_lock(free_space_root->node);
 	btrfs_clean_tree_block(free_space_root->node);
 	btrfs_tree_unlock(free_space_root->node);
-	btrfs_free_tree_block(trans, free_space_root, free_space_root->node,
-			      0, 1);
+	btrfs_free_tree_block(trans, btrfs_root_id(free_space_root),
+			      free_space_root->node, 0, 1);
 
 	btrfs_put_root(free_space_root);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/inode.c
@@ -60,8 +60,6 @@
 };
 
 struct btrfs_dio_data {
-	u64 reserve;
-	loff_t length;
 	ssize_t submitted;
 	struct extent_changeset *data_reserved;
 };
@@ -1055,6 +1053,28 @@
  * *page_started is set to one if we unlock locked_page and do everything
  * required to start IO on it.  It may be clean and already done with
  * IO when we return.
+ *
+ * When unlock == 1, we unlock the pages in successfully allocated regions.
+ * When unlock == 0, we leave them locked for writing them out.
+ *
+ * However, we unlock all the pages except @locked_page in case of failure.
+ *
+ * In summary, page locking state will be as follow:
+ *
+ * - page_started == 1 (return value)
+ *     - All the pages are unlocked. IO is started.
+ *     - Note that this can happen only on success
+ * - unlock == 1
+ *     - All the pages except @locked_page are unlocked in any case
+ * - unlock == 0
+ *     - On success, all the pages are locked for writing out them
+ *     - On failure, all the pages except @locked_page are unlocked
+ *
+ * When a failure happens in the second or later iteration of the
+ * while-loop, the ordered extents created in previous iterations are kept
+ * intact. So, the caller must clean them up by calling
+ * btrfs_cleanup_ordered_extents(). See btrfs_run_delalloc_range() for
+ * example.
  */
 static noinline int cow_file_range(struct btrfs_inode *inode,
 				   struct page *locked_page,
@@ -1064,6 +1084,7 @@
 	struct btrfs_root *root = inode->root;
 	struct btrfs_fs_info *fs_info = root->fs_info;
 	u64 alloc_hint = 0;
+	u64 orig_start = start;
 	u64 num_bytes;
 	unsigned long ram_size;
 	u64 cur_alloc_size = 0;
@@ -1077,7 +1098,6 @@
 	int ret = 0;
 
 	if (btrfs_is_free_space_inode(inode)) {
-		WARN_ON_ONCE(1);
 		ret = -EINVAL;
 		goto out_unlock;
 	}
@@ -1151,7 +1171,7 @@
 	 * fails during the stage where it updates the bytenr of file extent
 	 * items.
 	 */
-	if (root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID)
+	if (btrfs_is_data_reloc_root(root))
 		min_alloc_size = num_bytes;
 	else
 		min_alloc_size = fs_info->sectorsize;
@@ -1187,8 +1207,7 @@
 		if (ret)
 			goto out_drop_extent_cache;
 
-		if (root->root_key.objectid ==
-		    BTRFS_DATA_RELOC_TREE_OBJECTID) {
+		if (btrfs_is_data_reloc_root(root)) {
 			ret = btrfs_reloc_clone_csums(inode, start,
 						      cur_alloc_size);
 			/*
@@ -1249,18 +1268,44 @@
 	btrfs_dec_block_group_reservations(fs_info, ins.objectid);
 	btrfs_free_reserved_extent(fs_info, ins.objectid, ins.offset, 1);
 out_unlock:
+	/*
+	 * Now, we have three regions to clean up:
+	 *
+	 * |-------(1)----|---(2)---|-------------(3)----------|
+	 * `- orig_start  `- start  `- start + cur_alloc_size  `- end
+	 *
+	 * We process each region below.
+	 */
+
 	clear_bits = EXTENT_LOCKED | EXTENT_DELALLOC | EXTENT_DELALLOC_NEW |
 		EXTENT_DEFRAG | EXTENT_CLEAR_META_RESV;
 	page_ops = PAGE_UNLOCK | PAGE_START_WRITEBACK | PAGE_END_WRITEBACK;
+
 	/*
-	 * If we reserved an extent for our delalloc range (or a subrange) and
-	 * failed to create the respective ordered extent, then it means that
-	 * when we reserved the extent we decremented the extent's size from
-	 * the data space_info's bytes_may_use counter and incremented the
-	 * space_info's bytes_reserved counter by the same amount. We must make
-	 * sure extent_clear_unlock_delalloc() does not try to decrement again
-	 * the data space_info's bytes_may_use counter, therefore we do not pass
-	 * it the flag EXTENT_CLEAR_DATA_RESV.
+	 * For the range (1). We have already instantiated the ordered extents
+	 * for this region. They are cleaned up by
+	 * btrfs_cleanup_ordered_extents() in e.g,
+	 * btrfs_run_delalloc_range(). EXTENT_LOCKED | EXTENT_DELALLOC are
+	 * already cleared in the above loop. And, EXTENT_DELALLOC_NEW |
+	 * EXTENT_DEFRAG | EXTENT_CLEAR_META_RESV are handled by the cleanup
+	 * function.
+	 *
+	 * However, in case of unlock == 0, we still need to unlock the pages
+	 * (except @locked_page) to ensure all the pages are unlocked.
+	 */
+	if (!unlock && orig_start < start)
+		extent_clear_unlock_delalloc(inode, orig_start, start - 1,
+					     locked_page, 0, page_ops);
+
+	/*
+	 * For the range (2). If we reserved an extent for our delalloc range
+	 * (or a subrange) and failed to create the respective ordered extent,
+	 * then it means that when we reserved the extent we decremented the
+	 * extent's size from the data space_info's bytes_may_use counter and
+	 * incremented the space_info's bytes_reserved counter by the same
+	 * amount. We must make sure extent_clear_unlock_delalloc() does not try
+	 * to decrement again the data space_info's bytes_may_use counter,
+	 * therefore we do not pass it the flag EXTENT_CLEAR_DATA_RESV.
 	 */
 	if (extent_reserved) {
 		extent_clear_unlock_delalloc(inode, start,
@@ -1272,6 +1317,13 @@
 		if (start >= end)
 			goto out;
 	}
+
+	/*
+	 * For the range (3). We never touched the region. In addition to the
+	 * clear_bits above, we add EXTENT_CLEAR_DATA_RESV to release the data
+	 * space_info's bytes_may_use counter, reserved in
+	 * btrfs_check_data_free_space().
+	 */
 	extent_clear_unlock_delalloc(inode, start, end, locked_page,
 				     clear_bits | EXTENT_CLEAR_DATA_RESV,
 				     page_ops);
@@ -1504,8 +1556,7 @@
 			   int *page_started, unsigned long *nr_written)
 {
 	const bool is_space_ino = btrfs_is_free_space_inode(inode);
-	const bool is_reloc_ino = (inode->root->root_key.objectid ==
-				   BTRFS_DATA_RELOC_TREE_OBJECTID);
+	const bool is_reloc_ino = btrfs_is_data_reloc_root(inode->root);
 	const u64 range_bytes = end + 1 - start;
 	struct extent_io_tree *io_tree = &inode->io_tree;
 	u64 range_start = start;
@@ -1867,8 +1918,7 @@
 			btrfs_dec_nocow_writers(fs_info, disk_bytenr);
 		nocow = false;
 
-		if (root->root_key.objectid ==
-		    BTRFS_DATA_RELOC_TREE_OBJECTID)
+		if (btrfs_is_data_reloc_root(root))
 			/*
 			 * Error handled later, as we must prevent
 			 * extent_clear_unlock_delalloc() in error handler
@@ -1948,7 +1998,15 @@
 	const bool zoned = btrfs_is_zoned(inode->root->fs_info);
 
 	if (should_nocow(inode, start, end)) {
-		ASSERT(!zoned);
+		/*
+		 * Normally on a zoned device we're only doing COW writes, but
+		 * in case of relocation on a zoned filesystem we have taken
+		 * precaution, that we're only writing sequentially. It's safe
+		 * to use run_delalloc_nocow() here, like for  regular
+		 * preallocated inodes.
+		 */
+		ASSERT(!zoned ||
+		       (zoned && btrfs_is_data_reloc_root(inode->root)));
 		ret = run_delalloc_nocow(inode, locked_page, start, end,
 					 page_started, nr_written);
 	} else if (!inode_can_compress(inode) ||
@@ -1974,6 +2032,7 @@
 void btrfs_split_delalloc_extent(struct inode *inode,
 				 struct extent_state *orig, u64 split)
 {
+	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	u64 size;
 
 	/* not delalloc, ignore it */
@@ -1981,7 +2040,7 @@
 		return;
 
 	size = orig->end - orig->start + 1;
-	if (size > BTRFS_MAX_EXTENT_SIZE) {
+	if (size > fs_info->max_extent_size) {
 		u32 num_extents;
 		u64 new_size;
 
@@ -1990,10 +2049,10 @@
 		 * applies here, just in reverse.
 		 */
 		new_size = orig->end - split + 1;
-		num_extents = count_max_extents(new_size);
+		num_extents = count_max_extents(fs_info, new_size);
 		new_size = split - orig->start;
-		num_extents += count_max_extents(new_size);
-		if (count_max_extents(size) >= num_extents)
+		num_extents += count_max_extents(fs_info, new_size);
+		if (count_max_extents(fs_info, size) >= num_extents)
 			return;
 	}
 
@@ -2010,6 +2069,7 @@
 void btrfs_merge_delalloc_extent(struct inode *inode, struct extent_state *new,
 				 struct extent_state *other)
 {
+	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	u64 new_size, old_size;
 	u32 num_extents;
 
@@ -2023,7 +2083,7 @@
 		new_size = other->end - new->start + 1;
 
 	/* we're not bigger than the max, unreserve the space and go */
-	if (new_size <= BTRFS_MAX_EXTENT_SIZE) {
+	if (new_size <= fs_info->max_extent_size) {
 		spin_lock(&BTRFS_I(inode)->lock);
 		btrfs_mod_outstanding_extents(BTRFS_I(inode), -1);
 		spin_unlock(&BTRFS_I(inode)->lock);
@@ -2049,10 +2109,10 @@
 	 * this case.
 	 */
 	old_size = other->end - other->start + 1;
-	num_extents = count_max_extents(old_size);
+	num_extents = count_max_extents(fs_info, old_size);
 	old_size = new->end - new->start + 1;
-	num_extents += count_max_extents(old_size);
-	if (count_max_extents(new_size) >= num_extents)
+	num_extents += count_max_extents(fs_info, old_size);
+	if (count_max_extents(fs_info, new_size) >= num_extents)
 		return;
 
 	spin_lock(&BTRFS_I(inode)->lock);
@@ -2131,7 +2191,7 @@
 	if (!(state->state & EXTENT_DELALLOC) && (*bits & EXTENT_DELALLOC)) {
 		struct btrfs_root *root = BTRFS_I(inode)->root;
 		u64 len = state->end + 1 - state->start;
-		u32 num_extents = count_max_extents(len);
+		u32 num_extents = count_max_extents(fs_info, len);
 		bool do_list = !btrfs_is_free_space_inode(BTRFS_I(inode));
 
 		spin_lock(&BTRFS_I(inode)->lock);
@@ -2173,7 +2233,7 @@
 	struct btrfs_inode *inode = BTRFS_I(vfs_inode);
 	struct btrfs_fs_info *fs_info = btrfs_sb(vfs_inode->i_sb);
 	u64 len = state->end + 1 - state->start;
-	u32 num_extents = count_max_extents(len);
+	u32 num_extents = count_max_extents(fs_info, len);
 
 	if ((state->state & EXTENT_DEFRAG) && (*bits & EXTENT_DEFRAG)) {
 		spin_lock(&inode->lock);
@@ -2201,13 +2261,13 @@
 		 */
 		if (*bits & EXTENT_CLEAR_META_RESV &&
 		    root != fs_info->tree_root)
-			btrfs_delalloc_release_metadata(inode, len, false);
+			btrfs_delalloc_release_metadata(inode, len, true);
 
 		/* For sanity tests. */
 		if (btrfs_is_testing(fs_info))
 			return;
 
-		if (root->root_key.objectid != BTRFS_DATA_RELOC_TREE_OBJECTID &&
+		if (!btrfs_is_data_reloc_root(root) &&
 		    do_list && !(state->state & EXTENT_NORESERVE) &&
 		    (*bits & EXTENT_CLEAR_DATA_RESV))
 			btrfs_free_reserved_data_space_noquota(fs_info, len);
@@ -2532,7 +2592,7 @@
 		goto mapit;
 	} else if (async && !skip_sum) {
 		/* csum items have already been cloned */
-		if (root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID)
+		if (btrfs_is_data_reloc_root(root))
 			goto mapit;
 		/* we're doing a write, do the async checksumming */
 		ret = btrfs_wq_submit_bio(inode, bio, mirror_num, bio_flags,
@@ -3067,6 +3127,8 @@
 						ordered_extent->file_offset,
 						ordered_extent->file_offset +
 						logical_len);
+		btrfs_zoned_release_data_reloc_bg(fs_info, ordered_extent->disk_bytenr,
+						  ordered_extent->disk_num_bytes);
 	} else {
 		BUG_ON(root == fs_info->tree_root);
 		ret = insert_ordered_extent_file_extent(trans, ordered_extent);
@@ -3164,6 +3226,13 @@
 			btrfs_free_reserved_extent(fs_info,
 					ordered_extent->disk_bytenr,
 					ordered_extent->disk_num_bytes, 1);
+			/*
+			 * Actually free the qgroup rsv which was released when
+			 * the ordered extent was created.
+			 */
+			btrfs_qgroup_free_refroot(fs_info, inode->root->root_key.objectid,
+						  ordered_extent->qgroup_rsv,
+						  BTRFS_QGROUP_RSV_DATA);
 		}
 	}
 
@@ -3304,7 +3373,7 @@
 		u64 file_offset = pg_off + page_offset(page);
 		int ret;
 
-		if (root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID &&
+		if (btrfs_is_data_reloc_root(root) &&
 		    test_range_bit(io_tree, file_offset,
 				   file_offset + sectorsize - 1,
 				   EXTENT_NODATASUM, 1, NULL)) {
@@ -4005,7 +4074,7 @@
 	 * without delay
 	 */
 	if (!btrfs_is_free_space_inode(inode)
-	    && root->root_key.objectid != BTRFS_DATA_RELOC_TREE_OBJECTID
+	    && !btrfs_is_data_reloc_root(root)
 	    && !test_bit(BTRFS_FS_LOG_RECOVERING, &fs_info->flags)) {
 		btrfs_update_root_times(trans, root);
 
@@ -4035,11 +4104,11 @@
  * also drops the back refs in the inode to the directory
  */
 static int __btrfs_unlink_inode(struct btrfs_trans_handle *trans,
-				struct btrfs_root *root,
 				struct btrfs_inode *dir,
 				struct btrfs_inode *inode,
 				const char *name, int name_len)
 {
+	struct btrfs_root *root = dir->root;
 	struct btrfs_fs_info *fs_info = root->fs_info;
 	struct btrfs_path *path;
 	int ret = 0;
@@ -4130,6 +4199,7 @@
 
 	btrfs_i_size_write(dir, dir->vfs_inode.i_size - name_len * 2);
 	inode_inc_iversion(&inode->vfs_inode);
+	inode_set_ctime_current(&inode->vfs_inode);
 	inode_inc_iversion(&dir->vfs_inode);
 	inode->vfs_inode.i_ctime = dir->vfs_inode.i_mtime =
 		dir->vfs_inode.i_ctime = current_time(&inode->vfs_inode);
@@ -4139,15 +4209,14 @@
 }
 
 int btrfs_unlink_inode(struct btrfs_trans_handle *trans,
-		       struct btrfs_root *root,
 		       struct btrfs_inode *dir, struct btrfs_inode *inode,
 		       const char *name, int name_len)
 {
 	int ret;
-	ret = __btrfs_unlink_inode(trans, root, dir, inode, name, name_len);
+	ret = __btrfs_unlink_inode(trans, dir, inode, name, name_len);
 	if (!ret) {
 		drop_nlink(&inode->vfs_inode);
-		ret = btrfs_update_inode(trans, root, inode);
+		ret = btrfs_update_inode(trans, inode->root, inode);
 	}
 	return ret;
 }
@@ -4176,7 +4245,6 @@
 
 static int btrfs_unlink(struct inode *dir, struct dentry *dentry)
 {
-	struct btrfs_root *root = BTRFS_I(dir)->root;
 	struct btrfs_trans_handle *trans;
 	struct inode *inode = d_inode(dentry);
 	int ret;
@@ -4188,7 +4256,7 @@
 	btrfs_record_unlink_dir(trans, BTRFS_I(dir), BTRFS_I(d_inode(dentry)),
 			0);
 
-	ret = btrfs_unlink_inode(trans, root, BTRFS_I(dir),
+	ret = btrfs_unlink_inode(trans, BTRFS_I(dir),
 			BTRFS_I(d_inode(dentry)), dentry->d_name.name,
 			dentry->d_name.len);
 	if (ret)
@@ -4202,7 +4270,7 @@
 
 out:
 	btrfs_end_transaction(trans);
-	btrfs_btree_balance_dirty(root->fs_info);
+	btrfs_btree_balance_dirty(BTRFS_I(dir)->root->fs_info);
 	return ret;
 }
 
@@ -4344,7 +4412,14 @@
 	ret = btrfs_search_slot(NULL, fs_info->tree_root, &key, path, 0, 0);
 	if (ret < 0)
 		goto out;
-	BUG_ON(ret == 0);
+	if (ret == 0) {
+		/*
+		 * Key with offset -1 found, there would have to exist a root
+		 * with such id, but this is out of valid range.
+		 */
+		ret = -EUCLEAN;
+		goto out;
+	}
 
 	ret = 0;
 	if (path->slots[0] > 0) {
@@ -4434,6 +4509,8 @@
 	u64 root_flags;
 	int ret;
 
+	down_write(&fs_info->subvol_sem);
+
 	/*
 	 * Don't allow to delete a subvolume with send in progress. This is
 	 * inside the inode lock so the error handling that has to drop the bit
@@ -4445,18 +4522,25 @@
 		btrfs_warn(fs_info,
 			   "attempt to delete subvolume %llu during send",
 			   dest->root_key.objectid);
-		return -EPERM;
+		ret = -EPERM;
+		goto out_up_write;
+	}
+	if (atomic_read(&dest->nr_swapfiles)) {
+		spin_unlock(&dest->root_item_lock);
+		btrfs_warn(fs_info,
+			   "attempt to delete subvolume %llu with active swapfile",
+			   root->root_key.objectid);
+		ret = -EPERM;
+		goto out_up_write;
 	}
 	root_flags = btrfs_root_flags(&dest->root_item);
 	btrfs_set_root_flags(&dest->root_item,
 			     root_flags | BTRFS_ROOT_SUBVOL_DEAD);
 	spin_unlock(&dest->root_item_lock);
 
-	down_write(&fs_info->subvol_sem);
-
 	ret = may_destroy_subvol(dest);
 	if (ret)
-		goto out_up_write;
+		goto out_undead;
 
 	btrfs_init_block_rsv(&block_rsv, BTRFS_BLOCK_RSV_TEMP);
 	/*
@@ -4466,7 +4550,7 @@
 	 */
 	ret = btrfs_subvolume_reserve_metadata(root, &block_rsv, 5, true);
 	if (ret)
-		goto out_up_write;
+		goto out_undead;
 
 	trans = btrfs_start_transaction(root, 0);
 	if (IS_ERR(trans)) {
@@ -4532,15 +4616,17 @@
 	inode->i_flags |= S_DEAD;
 out_release:
 	btrfs_subvolume_release_metadata(root, &block_rsv);
-out_up_write:
-	up_write(&fs_info->subvol_sem);
+out_undead:
 	if (ret) {
 		spin_lock(&dest->root_item_lock);
 		root_flags = btrfs_root_flags(&dest->root_item);
 		btrfs_set_root_flags(&dest->root_item,
 				root_flags & ~BTRFS_ROOT_SUBVOL_DEAD);
 		spin_unlock(&dest->root_item_lock);
-	} else {
+	}
+out_up_write:
+	up_write(&fs_info->subvol_sem);
+	if (!ret) {
 		d_invalidate(dentry);
 		btrfs_prune_dentries(dest);
 		ASSERT(dest->send_in_progress == 0);
@@ -4553,7 +4639,6 @@
 {
 	struct inode *inode = d_inode(dentry);
 	int err = 0;
-	struct btrfs_root *root = BTRFS_I(dir)->root;
 	struct btrfs_trans_handle *trans;
 	u64 last_unlink_trans;
 
@@ -4578,7 +4663,7 @@
 	last_unlink_trans = BTRFS_I(inode)->last_unlink_trans;
 
 	/* now the directory is empty */
-	err = btrfs_unlink_inode(trans, root, BTRFS_I(dir),
+	err = btrfs_unlink_inode(trans, BTRFS_I(dir),
 			BTRFS_I(d_inode(dentry)), dentry->d_name.name,
 			dentry->d_name.len);
 	if (!err) {
@@ -4599,7 +4684,7 @@
 	}
 out:
 	btrfs_end_transaction(trans);
-	btrfs_btree_balance_dirty(root->fs_info);
+	btrfs_btree_balance_dirty(BTRFS_I(dir)->root->fs_info);
 
 	return err;
 }
@@ -4910,7 +4995,8 @@
 					extent_start, extent_num_bytes, 0);
 			ref.real_root = root->root_key.objectid;
 			btrfs_init_data_ref(&ref, btrfs_header_owner(leaf),
-					ino, extent_offset);
+					ino, extent_offset,
+					root->root_key.objectid, false);
 			ret = btrfs_free_extent(trans, &ref);
 			if (ret) {
 				btrfs_abort_transaction(trans, ret);
@@ -5963,7 +6049,7 @@
 	struct inode *inode;
 	struct btrfs_root *root = BTRFS_I(dir)->root;
 	struct btrfs_root *sub_root = root;
-	struct btrfs_key location;
+	struct btrfs_key location = { 0 };
 	u8 di_type = 0;
 	int ret = 0;
 
@@ -6048,6 +6134,78 @@
 }
 
 /*
+ * Find the highest existing sequence number in a directory and then set the
+ * in-memory index_cnt variable to the first free sequence number.
+ */
+static int btrfs_set_inode_index_count(struct btrfs_inode *inode)
+{
+	struct btrfs_root *root = inode->root;
+	struct btrfs_key key, found_key;
+	struct btrfs_path *path;
+	struct extent_buffer *leaf;
+	int ret;
+
+	key.objectid = btrfs_ino(inode);
+	key.type = BTRFS_DIR_INDEX_KEY;
+	key.offset = (u64)-1;
+
+	path = btrfs_alloc_path();
+	if (!path)
+		return -ENOMEM;
+
+	ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
+	if (ret < 0)
+		goto out;
+	/* FIXME: we should be able to handle this */
+	if (ret == 0)
+		goto out;
+	ret = 0;
+
+	if (path->slots[0] == 0) {
+		inode->index_cnt = BTRFS_DIR_START_INDEX;
+		goto out;
+	}
+
+	path->slots[0]--;
+
+	leaf = path->nodes[0];
+	btrfs_item_key_to_cpu(leaf, &found_key, path->slots[0]);
+
+	if (found_key.objectid != btrfs_ino(inode) ||
+	    found_key.type != BTRFS_DIR_INDEX_KEY) {
+		inode->index_cnt = BTRFS_DIR_START_INDEX;
+		goto out;
+	}
+
+	inode->index_cnt = found_key.offset + 1;
+out:
+	btrfs_free_path(path);
+	return ret;
+}
+
+static int btrfs_get_dir_last_index(struct btrfs_inode *dir, u64 *index)
+{
+	int ret = 0;
+
+	btrfs_inode_lock(&dir->vfs_inode, 0);
+	if (dir->index_cnt == (u64)-1) {
+		ret = btrfs_inode_delayed_dir_index_count(dir);
+		if (ret) {
+			ret = btrfs_set_inode_index_count(dir);
+			if (ret)
+				goto out;
+		}
+	}
+
+	/* index_cnt is the index number of next new entry, so decrement it. */
+	*index = dir->index_cnt - 1;
+out:
+	btrfs_inode_unlock(&dir->vfs_inode, 0);
+
+	return ret;
+}
+
+/*
  * All this infrastructure exists because dir_emit can fault, and we are holding
  * the tree lock when doing readdir.  For now just allocate a buffer and copy
  * our information into that, and then dir_emit from the buffer.  This is
@@ -6059,10 +6217,17 @@
 static int btrfs_opendir(struct inode *inode, struct file *file)
 {
 	struct btrfs_file_private *private;
+	u64 last_index;
+	int ret;
+
+	ret = btrfs_get_dir_last_index(BTRFS_I(inode), &last_index);
+	if (ret)
+		return ret;
 
 	private = kzalloc(sizeof(struct btrfs_file_private), GFP_KERNEL);
 	if (!private)
 		return -ENOMEM;
+	private->last_index = last_index;
 	private->filldir_buf = kzalloc(PAGE_SIZE, GFP_KERNEL);
 	if (!private->filldir_buf) {
 		kfree(private);
@@ -6072,6 +6237,19 @@
 	return 0;
 }
 
+static loff_t btrfs_dir_llseek(struct file *file, loff_t offset, int whence)
+{
+	struct btrfs_file_private *private = file->private_data;
+	int ret;
+
+	ret = btrfs_get_dir_last_index(BTRFS_I(file_inode(file)),
+				       &private->last_index);
+	if (ret)
+		return ret;
+
+	return generic_file_llseek(file, offset, whence);
+}
+
 struct dir_entry {
 	u64 ino;
 	u64 offset;
@@ -6131,7 +6309,8 @@
 
 	INIT_LIST_HEAD(&ins_list);
 	INIT_LIST_HEAD(&del_list);
-	put = btrfs_readdir_get_delayed_items(inode, &ins_list, &del_list);
+	put = btrfs_readdir_get_delayed_items(inode, private->last_index,
+					      &ins_list, &del_list);
 
 again:
 	key.type = BTRFS_DIR_INDEX_KEY;
@@ -6164,6 +6343,8 @@
 			break;
 		if (found_key.offset < ctx->pos)
 			goto next;
+		if (found_key.offset > private->last_index)
+			break;
 		if (btrfs_should_delete_dir_index(&del_list, found_key.offset))
 			goto next;
 		di = btrfs_item_ptr(leaf, slot, struct btrfs_dir_item);
@@ -6298,63 +6479,6 @@
 }
 
 /*
- * find the highest existing sequence number in a directory
- * and then set the in-memory index_cnt variable to reflect
- * free sequence numbers
- */
-static int btrfs_set_inode_index_count(struct btrfs_inode *inode)
-{
-	struct btrfs_root *root = inode->root;
-	struct btrfs_key key, found_key;
-	struct btrfs_path *path;
-	struct extent_buffer *leaf;
-	int ret;
-
-	key.objectid = btrfs_ino(inode);
-	key.type = BTRFS_DIR_INDEX_KEY;
-	key.offset = (u64)-1;
-
-	path = btrfs_alloc_path();
-	if (!path)
-		return -ENOMEM;
-
-	ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
-	if (ret < 0)
-		goto out;
-	/* FIXME: we should be able to handle this */
-	if (ret == 0)
-		goto out;
-	ret = 0;
-
-	/*
-	 * MAGIC NUMBER EXPLANATION:
-	 * since we search a directory based on f_pos we have to start at 2
-	 * since '.' and '..' have f_pos of 0 and 1 respectively, so everybody
-	 * else has to start at 2
-	 */
-	if (path->slots[0] == 0) {
-		inode->index_cnt = 2;
-		goto out;
-	}
-
-	path->slots[0]--;
-
-	leaf = path->nodes[0];
-	btrfs_item_key_to_cpu(leaf, &found_key, path->slots[0]);
-
-	if (found_key.objectid != btrfs_ino(inode) ||
-	    found_key.type != BTRFS_DIR_INDEX_KEY) {
-		inode->index_cnt = 2;
-		goto out;
-	}
-
-	inode->index_cnt = found_key.offset + 1;
-out:
-	btrfs_free_path(path);
-	return ret;
-}
-
-/*
  * helper to find a free sequence number in a given directory.  This current
  * code is very simple, later versions will do smarter things in the btree
  */
@@ -6888,7 +7012,7 @@
 				goto fail;
 		}
 		d_instantiate(dentry, inode);
-		btrfs_log_new_name(trans, BTRFS_I(inode), NULL, parent);
+		btrfs_log_new_name(trans, old_dentry, NULL, parent);
 	}
 
 fail:
@@ -7758,6 +7882,11 @@
 {
 	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	struct extent_map *em = *map;
+	int type;
+	u64 block_start, orig_start, orig_block_len, ram_bytes;
+	bool can_nocow = false;
+	bool space_reserved = false;
+	u64 prev_len;
 	int ret = 0;
 
 	/*
@@ -7772,9 +7901,6 @@
 	if (test_bit(EXTENT_FLAG_PREALLOC, &em->flags) ||
 	    ((BTRFS_I(inode)->flags & BTRFS_INODE_NODATACOW) &&
 	     em->block_start != EXTENT_MAP_HOLE)) {
-		int type;
-		u64 block_start, orig_start, orig_block_len, ram_bytes;
-
 		if (test_bit(EXTENT_FLAG_PREALLOC, &em->flags))
 			type = BTRFS_ORDERED_PREALLOC;
 		else
@@ -7784,53 +7910,91 @@
 
 		if (can_nocow_extent(inode, start, &len, &orig_start,
 				     &orig_block_len, &ram_bytes, false) == 1 &&
-		    btrfs_inc_nocow_writers(fs_info, block_start)) {
-			struct extent_map *em2;
+		    btrfs_inc_nocow_writers(fs_info, block_start))
+			can_nocow = true;
+	}
 
-			em2 = btrfs_create_dio_extent(BTRFS_I(inode), start, len,
-						      orig_start, block_start,
-						      len, orig_block_len,
-						      ram_bytes, type);
+	prev_len = len;
+	if (can_nocow) {
+		struct extent_map *em2;
+
+		/* We can NOCOW, so only need to reserve metadata space. */
+		ret = btrfs_delalloc_reserve_metadata(BTRFS_I(inode), len);
+		if (ret < 0) {
+			/* Our caller expects us to free the input extent map. */
+			free_extent_map(em);
+			*map = NULL;
 			btrfs_dec_nocow_writers(fs_info, block_start);
-			if (type == BTRFS_ORDERED_PREALLOC) {
-				free_extent_map(em);
-				*map = em = em2;
-			}
+			goto out;
+		}
+		space_reserved = true;
 
-			if (em2 && IS_ERR(em2)) {
-				ret = PTR_ERR(em2);
-				goto out;
-			}
-			/*
-			 * For inode marked NODATACOW or extent marked PREALLOC,
-			 * use the existing or preallocated extent, so does not
-			 * need to adjust btrfs_space_info's bytes_may_use.
-			 */
-			btrfs_free_reserved_data_space_noquota(fs_info, len);
-			goto skip_cow;
+		em2 = btrfs_create_dio_extent(BTRFS_I(inode), start, len,
+					      orig_start, block_start,
+					      len, orig_block_len,
+					      ram_bytes, type);
+		btrfs_dec_nocow_writers(fs_info, block_start);
+		if (type == BTRFS_ORDERED_PREALLOC) {
+			free_extent_map(em);
+			*map = em = em2;
 		}
-	}
 
-	/* this will cow the extent */
-	free_extent_map(em);
-	*map = em = btrfs_new_extent_direct(BTRFS_I(inode), start, len);
-	if (IS_ERR(em)) {
-		ret = PTR_ERR(em);
-		goto out;
+		if (IS_ERR(em2)) {
+			ret = PTR_ERR(em2);
+			goto out;
+		}
+	} else {
+		/* Our caller expects us to free the input extent map. */
+		free_extent_map(em);
+		*map = NULL;
+
+		/* We have to COW, so need to reserve metadata and data space. */
+		ret = btrfs_delalloc_reserve_space(BTRFS_I(inode),
+						   &dio_data->data_reserved,
+						   start, len);
+		if (ret < 0)
+			goto out;
+		space_reserved = true;
+
+		em = btrfs_new_extent_direct(BTRFS_I(inode), start, len);
+		if (IS_ERR(em)) {
+			ret = PTR_ERR(em);
+			goto out;
+		}
+		*map = em;
+		len = min(len, em->len - (start - em->start));
+		if (len < prev_len)
+			btrfs_delalloc_release_space(BTRFS_I(inode),
+						     dio_data->data_reserved,
+						     start + len, prev_len - len,
+						     true);
 	}
 
-	len = min(len, em->len - (start - em->start));
+	/*
+	 * We have created our ordered extent, so we can now release our reservation
+	 * for an outstanding extent.
+	 */
+	btrfs_delalloc_release_extents(BTRFS_I(inode), prev_len);
 
-skip_cow:
 	/*
 	 * Need to update the i_size under the extent lock so buffered
 	 * readers will get the updated i_size when we unlock.
 	 */
 	if (start + len > i_size_read(inode))
 		i_size_write(inode, start + len);
-
-	dio_data->reserve -= len;
 out:
+	if (ret && space_reserved) {
+		btrfs_delalloc_release_extents(BTRFS_I(inode), len);
+		if (can_nocow) {
+			btrfs_delalloc_release_metadata(BTRFS_I(inode), len, true);
+		} else {
+			btrfs_delalloc_release_space(BTRFS_I(inode),
+						     dio_data->data_reserved,
+						     start, len, true);
+			extent_changeset_free(dio_data->data_reserved);
+			dio_data->data_reserved = NULL;
+		}
+	}
 	return ret;
 }
 
@@ -7872,18 +8036,6 @@
 	if (!dio_data)
 		return -ENOMEM;
 
-	dio_data->length = length;
-	if (write) {
-		dio_data->reserve = round_up(length, fs_info->sectorsize);
-		ret = btrfs_delalloc_reserve_space(BTRFS_I(inode),
-				&dio_data->data_reserved,
-				start, dio_data->reserve);
-		if (ret) {
-			extent_changeset_free(dio_data->data_reserved);
-			kfree(dio_data);
-			return ret;
-		}
-	}
 	iomap->private = dio_data;
 
 
@@ -7919,11 +8071,51 @@
 	if (test_bit(EXTENT_FLAG_COMPRESSED, &em->flags) ||
 	    em->block_start == EXTENT_MAP_INLINE) {
 		free_extent_map(em);
-		ret = -ENOTBLK;
+		/*
+		 * If we are in a NOWAIT context, return -EAGAIN in order to
+		 * fallback to buffered IO. This is not only because we can
+		 * block with buffered IO (no support for NOWAIT semantics at
+		 * the moment) but also to avoid returning short reads to user
+		 * space - this happens if we were able to read some data from
+		 * previous non-compressed extents and then when we fallback to
+		 * buffered IO, at btrfs_file_read_iter() by calling
+		 * filemap_read(), we fail to fault in pages for the read buffer,
+		 * in which case filemap_read() returns a short read (the number
+		 * of bytes previously read is > 0, so it does not return -EFAULT).
+		 */
+		ret = (flags & IOMAP_NOWAIT) ? -EAGAIN : -ENOTBLK;
 		goto unlock_err;
 	}
 
 	len = min(len, em->len - (start - em->start));
+
+	/*
+	 * If we have a NOWAIT request and the range contains multiple extents
+	 * (or a mix of extents and holes), then we return -EAGAIN to make the
+	 * caller fallback to a context where it can do a blocking (without
+	 * NOWAIT) request. This way we avoid doing partial IO and returning
+	 * success to the caller, which is not optimal for writes and for reads
+	 * it can result in unexpected behaviour for an application.
+	 *
+	 * When doing a read, because we use IOMAP_DIO_PARTIAL when calling
+	 * iomap_dio_rw(), we can end up returning less data then what the caller
+	 * asked for, resulting in an unexpected, and incorrect, short read.
+	 * That is, the caller asked to read N bytes and we return less than that,
+	 * which is wrong unless we are crossing EOF. This happens if we get a
+	 * page fault error when trying to fault in pages for the buffer that is
+	 * associated to the struct iov_iter passed to iomap_dio_rw(), and we
+	 * have previously submitted bios for other extents in the range, in
+	 * which case iomap_dio_rw() may return us EIOCBQUEUED if not all of
+	 * those bios have completed by the time we get the page fault error,
+	 * which we return back to our caller - we should only return EIOCBQUEUED
+	 * after we have submitted bios for all the extents in the range.
+	 */
+	if ((flags & IOMAP_NOWAIT) && len < length) {
+		free_extent_map(em);
+		ret = -EAGAIN;
+		goto unlock_err;
+	}
+
 	if (write) {
 		ret = btrfs_get_blocks_direct_write(&em, inode, dio_data,
 						    start, len);
@@ -7962,7 +8154,7 @@
 		iomap->type = IOMAP_MAPPED;
 	}
 	iomap->offset = start;
-	iomap->bdev = fs_info->fs_devices->latest_bdev;
+	iomap->bdev = fs_info->fs_devices->latest_dev->bdev;
 	iomap->length = len;
 
 	if (write && btrfs_use_zone_append(BTRFS_I(inode), em->block_start))
@@ -7976,14 +8168,8 @@
 	unlock_extent_cached(&BTRFS_I(inode)->io_tree, lockstart, lockend,
 			     &cached_state);
 err:
-	if (dio_data) {
-		btrfs_delalloc_release_space(BTRFS_I(inode),
-				dio_data->data_reserved, start,
-				dio_data->reserve, true);
-		btrfs_delalloc_release_extents(BTRFS_I(inode), dio_data->reserve);
-		extent_changeset_free(dio_data->data_reserved);
-		kfree(dio_data);
-	}
+	kfree(dio_data);
+
 	return ret;
 }
 
@@ -8013,14 +8199,8 @@
 		ret = -ENOTBLK;
 	}
 
-	if (write) {
-		if (dio_data->reserve)
-			btrfs_delalloc_release_space(BTRFS_I(inode),
-					dio_data->data_reserved, pos,
-					dio_data->reserve, true);
-		btrfs_delalloc_release_extents(BTRFS_I(inode), dio_data->length);
+	if (write)
 		extent_changeset_free(dio_data->data_reserved);
-	}
 out:
 	kfree(dio_data);
 	iomap->private = NULL;
@@ -9451,7 +9631,7 @@
 	if (old_ino == BTRFS_FIRST_FREE_OBJECTID) {
 		ret = btrfs_unlink_subvol(trans, old_dir, old_dentry);
 	} else { /* src is an inode */
-		ret = __btrfs_unlink_inode(trans, root, BTRFS_I(old_dir),
+		ret = __btrfs_unlink_inode(trans, BTRFS_I(old_dir),
 					   BTRFS_I(old_dentry->d_inode),
 					   old_dentry->d_name.name,
 					   old_dentry->d_name.len);
@@ -9467,7 +9647,7 @@
 	if (new_ino == BTRFS_FIRST_FREE_OBJECTID) {
 		ret = btrfs_unlink_subvol(trans, new_dir, new_dentry);
 	} else { /* dest is an inode */
-		ret = __btrfs_unlink_inode(trans, dest, BTRFS_I(new_dir),
+		ret = __btrfs_unlink_inode(trans, BTRFS_I(new_dir),
 					   BTRFS_I(new_dentry->d_inode),
 					   new_dentry->d_name.name,
 					   new_dentry->d_name.len);
@@ -9501,13 +9681,13 @@
 		BTRFS_I(new_inode)->dir_index = new_idx;
 
 	if (root_log_pinned) {
-		btrfs_log_new_name(trans, BTRFS_I(old_inode), BTRFS_I(old_dir),
+		btrfs_log_new_name(trans, old_dentry, BTRFS_I(old_dir),
 				   new_dentry->d_parent);
 		btrfs_end_log_trans(root);
 		root_log_pinned = false;
 	}
 	if (dest_log_pinned) {
-		btrfs_log_new_name(trans, BTRFS_I(new_inode), BTRFS_I(new_dir),
+		btrfs_log_new_name(trans, new_dentry, BTRFS_I(new_dir),
 				   old_dentry->d_parent);
 		btrfs_end_log_trans(dest);
 		dest_log_pinned = false;
@@ -9742,7 +9922,7 @@
 		 */
 		btrfs_pin_log_trans(root);
 		log_pinned = true;
-		ret = __btrfs_unlink_inode(trans, root, BTRFS_I(old_dir),
+		ret = __btrfs_unlink_inode(trans, BTRFS_I(old_dir),
 					BTRFS_I(d_inode(old_dentry)),
 					old_dentry->d_name.name,
 					old_dentry->d_name.len);
@@ -9762,7 +9942,7 @@
 			ret = btrfs_unlink_subvol(trans, new_dir, new_dentry);
 			BUG_ON(new_inode->i_nlink == 0);
 		} else {
-			ret = btrfs_unlink_inode(trans, dest, BTRFS_I(new_dir),
+			ret = btrfs_unlink_inode(trans, BTRFS_I(new_dir),
 						 BTRFS_I(d_inode(new_dentry)),
 						 new_dentry->d_name.name,
 						 new_dentry->d_name.len);
@@ -9788,7 +9968,7 @@
 		BTRFS_I(old_inode)->dir_index = index;
 
 	if (log_pinned) {
-		btrfs_log_new_name(trans, BTRFS_I(old_inode), BTRFS_I(old_dir),
+		btrfs_log_new_name(trans, old_dentry, BTRFS_I(old_dir),
 				   new_dentry->d_parent);
 		btrfs_end_log_trans(root);
 		log_pinned = false;
@@ -10581,9 +10761,19 @@
 				 struct btrfs_swap_info *bsi)
 {
 	unsigned long nr_pages;
+	unsigned long max_pages;
 	u64 first_ppage, first_ppage_reported, next_ppage;
 	int ret;
 
+	/*
+	 * Our swapfile may have had its size extended after the swap header was
+	 * written. In that case activating the swapfile should not go beyond
+	 * the max size set in the swap header.
+	 */
+	if (bsi->nr_pages >= sis->max)
+		return 0;
+
+	max_pages = sis->max - bsi->nr_pages;
 	first_ppage = ALIGN(bsi->block_start, PAGE_SIZE) >> PAGE_SHIFT;
 	next_ppage = ALIGN_DOWN(bsi->block_start + bsi->block_len,
 				PAGE_SIZE) >> PAGE_SHIFT;
@@ -10591,6 +10781,7 @@
 	if (first_ppage >= next_ppage)
 		return 0;
 	nr_pages = next_ppage - first_ppage;
+	nr_pages = min(nr_pages, max_pages);
 
 	first_ppage_reported = first_ppage;
 	if (bsi->start == 0)
@@ -10691,8 +10882,24 @@
 	 * set. We use this counter to prevent snapshots. We must increment it
 	 * before walking the extents because we don't want a concurrent
 	 * snapshot to run after we've already checked the extents.
-	 */
+	 *
+	 * It is possible that subvolume is marked for deletion but still not
+	 * removed yet. To prevent this race, we check the root status before
+	 * activating the swapfile.
+	 */
+	spin_lock(&root->root_item_lock);
+	if (btrfs_root_dead(root)) {
+		spin_unlock(&root->root_item_lock);
+
+		btrfs_drew_write_unlock(&root->snapshot_lock);
+		btrfs_exclop_finish(fs_info);
+		btrfs_warn(fs_info,
+		"cannot activate swapfile because subvolume %llu is being deleted",
+			root->root_key.objectid);
+		return -EPERM;
+	}
 	atomic_inc(&root->nr_swapfiles);
+	spin_unlock(&root->root_item_lock);
 
 	isize = ALIGN_DOWN(inode->i_size, fs_info->sectorsize);
 
@@ -10824,6 +11031,8 @@
 		}
 
 		start += len;
+
+		cond_resched();
 	}
 
 	if (bsi.block_len)
@@ -10909,7 +11118,7 @@
 };
 
 static const struct file_operations btrfs_dir_file_operations = {
-	.llseek		= generic_file_llseek,
+	.llseek		= btrfs_dir_llseek,
 	.read		= generic_read_dir,
 	.iterate_shared	= btrfs_real_readdir,
 	.open		= btrfs_opendir,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/ioctl.c
@@ -615,11 +615,13 @@
 		 * Since we don't abort the transaction in this case, free the
 		 * tree block so that we don't leak space and leave the
 		 * filesystem in an inconsistent state (an extent item in the
-		 * extent tree without backreferences). Also no need to have
-		 * the tree block locked since it is not in any tree at this
-		 * point, so no other task can find it and use it.
+		 * extent tree with a backreference for a root that does not
+		 * exists).
 		 */
-		btrfs_free_tree_block(trans, root, leaf, 0, 1);
+		btrfs_tree_lock(leaf);
+		btrfs_clean_tree_block(leaf);
+		btrfs_tree_unlock(leaf);
+		btrfs_free_tree_block(trans, objectid, leaf, 0, 1);
 		free_extent_buffer(leaf);
 		goto fail;
 	}
@@ -628,7 +630,7 @@
 	leaf = NULL;
 
 	key.offset = (u64)-1;
-	new_root = btrfs_get_new_fs_root(fs_info, objectid, anon_dev);
+	new_root = btrfs_get_new_fs_root(fs_info, objectid, &anon_dev);
 	if (IS_ERR(new_root)) {
 		free_anon_bdev(anon_dev);
 		ret = PTR_ERR(new_root);
@@ -723,6 +725,9 @@
 	struct btrfs_trans_handle *trans;
 	int ret;
 
+	if (btrfs_root_refs(&root->root_item) == 0)
+		return -ENOENT;
+
 	if (!test_bit(BTRFS_ROOT_SHAREABLE, &root->state))
 		return -EINVAL;
 
@@ -775,10 +780,7 @@
 		goto fail;
 	}
 
-	spin_lock(&fs_info->trans_lock);
-	list_add(&pending_snapshot->list,
-		 &trans->transaction->pending_snapshots);
-	spin_unlock(&fs_info->trans_lock);
+	trans->pending_snapshot = pending_snapshot;
 
 	ret = btrfs_commit_transaction(trans);
 	if (ret)
@@ -1658,6 +1660,7 @@
 static noinline int btrfs_ioctl_resize(struct file *file,
 					void __user *arg)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct inode *inode = file_inode(file);
 	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	u64 new_size;
@@ -1713,7 +1716,8 @@
 		btrfs_info(fs_info, "resizing devid %llu", devid);
 	}
 
-	device = btrfs_find_device(fs_info->fs_devices, devid, NULL, NULL);
+	args.devid = devid;
+	device = btrfs_find_device(fs_info->fs_devices, &args);
 	if (!device) {
 		btrfs_info(fs_info, "resizer unable to find device %llu",
 			   devid);
@@ -1854,6 +1858,15 @@
 			 * are limited to own subvolumes only
 			 */
 			ret = -EPERM;
+		} else if (btrfs_ino(BTRFS_I(src_inode)) != BTRFS_FIRST_FREE_OBJECTID) {
+			/*
+			 * Snapshots must be made with the src_inode referring
+			 * to the subvolume inode, otherwise the permission
+			 * checking above is useless because we may have
+			 * permission on a lower directory but not the subvol
+			 * itself.
+			 */
+			ret = -EINVAL;
 		} else {
 			ret = btrfs_mksnapshot(&file->f_path, mnt_userns,
 					       name, namelen,
@@ -2093,7 +2106,7 @@
 static noinline int copy_to_sk(struct btrfs_path *path,
 			       struct btrfs_key *key,
 			       struct btrfs_ioctl_search_key *sk,
-			       size_t *buf_size,
+			       u64 *buf_size,
 			       char __user *ubuf,
 			       unsigned long *sk_offset,
 			       int *num_found)
@@ -2225,7 +2238,7 @@
 
 static noinline int search_ioctl(struct inode *inode,
 				 struct btrfs_ioctl_search_key *sk,
-				 size_t *buf_size,
+				 u64 *buf_size,
 				 char __user *ubuf)
 {
 	struct btrfs_fs_info *info = btrfs_sb(inode->i_sb);
@@ -2261,9 +2274,8 @@
 	key.offset = sk->min_offset;
 
 	while (1) {
-		ret = fault_in_pages_writeable(ubuf + sk_offset,
-					       *buf_size - sk_offset);
-		if (ret)
+		ret = -EFAULT;
+		if (fault_in_writeable(ubuf + sk_offset, *buf_size - sk_offset))
 			break;
 
 		ret = btrfs_search_forward(root, &key, path, sk->min_transid);
@@ -2295,7 +2307,7 @@
 	struct btrfs_ioctl_search_key sk;
 	struct inode *inode;
 	int ret;
-	size_t buf_size;
+	u64 buf_size;
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
@@ -2329,8 +2341,8 @@
 	struct btrfs_ioctl_search_args_v2 args;
 	struct inode *inode;
 	int ret;
-	size_t buf_size;
-	const size_t buf_limit = SZ_16M;
+	u64 buf_size;
+	const u64 buf_limit = SZ_16M;
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
@@ -2526,6 +2538,13 @@
 				goto out_put;
 			}
 
+			/*
+			 * We don't need the path anymore, so release it and
+			 * avoid deadlocks and lockdep warnings in case
+			 * btrfs_iget() needs to lookup the inode from its root
+			 * btree and lock the same leaf.
+			 */
+			btrfs_release_path(path);
 			temp_inode = btrfs_iget(sb, key2.objectid, root);
 			if (IS_ERR(temp_inode)) {
 				ret = PTR_ERR(temp_inode);
@@ -2546,7 +2565,6 @@
 				goto out_put;
 			}
 
-			btrfs_release_path(path);
 			key.objectid = key.offset;
 			key.offset = (u64)-1;
 			dirid = key.objectid;
@@ -2788,6 +2806,8 @@
 		}
 	}
 
+	btrfs_free_path(path);
+	path = NULL;
 	if (copy_to_user(argp, subvol_info, sizeof(*subvol_info)))
 		ret = -EFAULT;
 
@@ -2880,6 +2900,8 @@
 	}
 
 out:
+	btrfs_free_path(path);
+
 	if (!ret || ret == -EOVERFLOW) {
 		rootrefs->num_items = found;
 		/* update min_treeid for next search */
@@ -2891,7 +2913,6 @@
 	}
 
 	kfree(rootrefs);
-	btrfs_free_path(path);
 
 	return ret;
 }
@@ -3098,10 +3119,8 @@
 	btrfs_inode_lock(inode, 0);
 	err = btrfs_delete_subvolume(dir, dentry);
 	btrfs_inode_unlock(inode, 0);
-	if (!err) {
-		fsnotify_rmdir(dir, dentry);
-		d_delete(dentry);
-	}
+	if (!err)
+		d_delete_notify(dir, dentry);
 
 out_dput:
 	dput(dentry);
@@ -3167,6 +3186,10 @@
 				ret = -EFAULT;
 				goto out;
 			}
+			if (range.flags & ~BTRFS_DEFRAG_RANGE_FLAGS_SUPP) {
+				ret = -EOPNOTSUPP;
+				goto out;
+			}
 			/* compression requires us to start the IO */
 			if ((range.flags & BTRFS_DEFRAG_RANGE_COMPRESS)) {
 				range.flags |= BTRFS_DEFRAG_RANGE_START_IO;
@@ -3220,6 +3243,7 @@
 
 static long btrfs_ioctl_rm_dev_v2(struct file *file, void __user *arg)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct inode *inode = file_inode(file);
 	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	struct btrfs_ioctl_vol_args_v2 *vol_args;
@@ -3231,35 +3255,37 @@
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
 
-	ret = mnt_want_write_file(file);
-	if (ret)
-		return ret;
-
 	vol_args = memdup_user(arg, sizeof(*vol_args));
-	if (IS_ERR(vol_args)) {
-		ret = PTR_ERR(vol_args);
-		goto err_drop;
-	}
+	if (IS_ERR(vol_args))
+		return PTR_ERR(vol_args);
 
 	if (vol_args->flags & ~BTRFS_DEVICE_REMOVE_ARGS_MASK) {
 		ret = -EOPNOTSUPP;
 		goto out;
 	}
+
 	vol_args->name[BTRFS_SUBVOL_NAME_MAX] = '\0';
-	if (!(vol_args->flags & BTRFS_DEVICE_SPEC_BY_ID) &&
-	    strcmp("cancel", vol_args->name) == 0)
+	if (vol_args->flags & BTRFS_DEVICE_SPEC_BY_ID) {
+		args.devid = vol_args->devid;
+	} else if (!strcmp("cancel", vol_args->name)) {
 		cancel = true;
+	} else {
+		ret = btrfs_get_dev_args_from_path(fs_info, &args, vol_args->name);
+		if (ret)
+			goto out;
+	}
+
+	ret = mnt_want_write_file(file);
+	if (ret)
+		goto out;
 
 	ret = exclop_start_or_cancel_reloc(fs_info, BTRFS_EXCLOP_DEV_REMOVE,
 					   cancel);
 	if (ret)
-		goto out;
-	/* Exclusive operation is now claimed */
+		goto err_drop;
 
-	if (vol_args->flags & BTRFS_DEVICE_SPEC_BY_ID)
-		ret = btrfs_rm_device(fs_info, NULL, vol_args->devid, &bdev, &mode);
-	else
-		ret = btrfs_rm_device(fs_info, vol_args->name, 0, &bdev, &mode);
+	/* Exclusive operation is now claimed */
+	ret = btrfs_rm_device(fs_info, &args, &bdev, &mode);
 
 	btrfs_exclop_finish(fs_info);
 
@@ -3271,54 +3297,62 @@
 			btrfs_info(fs_info, "device deleted: %s",
 					vol_args->name);
 	}
-out:
-	kfree(vol_args);
 err_drop:
 	mnt_drop_write_file(file);
 	if (bdev)
 		blkdev_put(bdev, mode);
+out:
+	btrfs_put_dev_args_from_path(&args);
+	kfree(vol_args);
 	return ret;
 }
 
 static long btrfs_ioctl_rm_dev(struct file *file, void __user *arg)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct inode *inode = file_inode(file);
 	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	struct btrfs_ioctl_vol_args *vol_args;
 	struct block_device *bdev = NULL;
 	fmode_t mode;
 	int ret;
-	bool cancel;
+	bool cancel = false;
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
 
-	ret = mnt_want_write_file(file);
-	if (ret)
-		return ret;
-
 	vol_args = memdup_user(arg, sizeof(*vol_args));
-	if (IS_ERR(vol_args)) {
-		ret = PTR_ERR(vol_args);
-		goto out_drop_write;
-	}
+	if (IS_ERR(vol_args))
+		return PTR_ERR(vol_args);
+
 	vol_args->name[BTRFS_PATH_NAME_MAX] = '\0';
-	cancel = (strcmp("cancel", vol_args->name) == 0);
+	if (!strcmp("cancel", vol_args->name)) {
+		cancel = true;
+	} else {
+		ret = btrfs_get_dev_args_from_path(fs_info, &args, vol_args->name);
+		if (ret)
+			goto out;
+	}
+
+	ret = mnt_want_write_file(file);
+	if (ret)
+		goto out;
 
 	ret = exclop_start_or_cancel_reloc(fs_info, BTRFS_EXCLOP_DEV_REMOVE,
 					   cancel);
 	if (ret == 0) {
-		ret = btrfs_rm_device(fs_info, vol_args->name, 0, &bdev, &mode);
+		ret = btrfs_rm_device(fs_info, &args, &bdev, &mode);
 		if (!ret)
 			btrfs_info(fs_info, "disk deleted %s", vol_args->name);
 		btrfs_exclop_finish(fs_info);
 	}
 
-	kfree(vol_args);
-out_drop_write:
 	mnt_drop_write_file(file);
 	if (bdev)
 		blkdev_put(bdev, mode);
+out:
+	btrfs_put_dev_args_from_path(&args);
+	kfree(vol_args);
 	return ret;
 }
 
@@ -3379,22 +3413,21 @@
 static long btrfs_ioctl_dev_info(struct btrfs_fs_info *fs_info,
 				 void __user *arg)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct btrfs_ioctl_dev_info_args *di_args;
 	struct btrfs_device *dev;
 	int ret = 0;
-	char *s_uuid = NULL;
 
 	di_args = memdup_user(arg, sizeof(*di_args));
 	if (IS_ERR(di_args))
 		return PTR_ERR(di_args);
 
+	args.devid = di_args->devid;
 	if (!btrfs_is_empty_uuid(di_args->uuid))
-		s_uuid = di_args->uuid;
+		args.uuid = di_args->uuid;
 
 	rcu_read_lock();
-	dev = btrfs_find_device(fs_info->fs_devices, di_args->devid, s_uuid,
-				NULL);
-
+	dev = btrfs_find_device(fs_info->fs_devices, &args);
 	if (!dev) {
 		ret = -ENODEV;
 		goto out;
@@ -3404,13 +3437,10 @@
 	di_args->bytes_used = btrfs_device_get_bytes_used(dev);
 	di_args->total_bytes = btrfs_device_get_total_bytes(dev);
 	memcpy(di_args->uuid, dev->uuid, sizeof(di_args->uuid));
-	if (dev->name) {
-		strncpy(di_args->path, rcu_str_deref(dev->name),
-				sizeof(di_args->path) - 1);
-		di_args->path[sizeof(di_args->path) - 1] = 0;
-	} else {
+	if (dev->name)
+		strscpy(di_args->path, rcu_str_deref(dev->name), sizeof(di_args->path));
+	else
 		di_args->path[0] = '\0';
-	}
 
 out:
 	rcu_read_unlock();
@@ -3517,7 +3547,7 @@
 static long btrfs_ioctl_space_info(struct btrfs_fs_info *fs_info,
 				   void __user *arg)
 {
-	struct btrfs_ioctl_space_args space_args;
+	struct btrfs_ioctl_space_args space_args = { 0 };
 	struct btrfs_ioctl_space_info space;
 	struct btrfs_ioctl_space_info *dest;
 	struct btrfs_ioctl_space_info *dest_orig;
@@ -3707,6 +3737,11 @@
 	if (IS_ERR(sa))
 		return PTR_ERR(sa);
 
+	if (sa->flags & ~BTRFS_SCRUB_SUPPORTED_FLAGS) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
 	if (!(sa->flags & BTRFS_SCRUB_READONLY)) {
 		ret = mnt_want_write_file(file);
 		if (ret)
@@ -3883,6 +3918,8 @@
 		ipath->fspath->val[i] = rel_ptr;
 	}
 
+	btrfs_free_path(path);
+	path = NULL;
 	ret = copy_to_user((void __user *)(unsigned long)ipa->fspath,
 			   ipath->fspath, size);
 	if (ret) {
@@ -3898,26 +3935,6 @@
 	return ret;
 }
 
-static int build_ino_list(u64 inum, u64 offset, u64 root, void *ctx)
-{
-	struct btrfs_data_container *inodes = ctx;
-	const size_t c = 3 * sizeof(u64);
-
-	if (inodes->bytes_left >= c) {
-		inodes->bytes_left -= c;
-		inodes->val[inodes->elem_cnt] = inum;
-		inodes->val[inodes->elem_cnt + 1] = offset;
-		inodes->val[inodes->elem_cnt + 2] = root;
-		inodes->elem_cnt += 3;
-	} else {
-		inodes->bytes_missing += c - inodes->bytes_left;
-		inodes->bytes_left = 0;
-		inodes->elem_missed += 3;
-	}
-
-	return 0;
-}
-
 static long btrfs_ioctl_logical_to_ino(struct btrfs_fs_info *fs_info,
 					void __user *arg, int version)
 {
@@ -3953,21 +3970,20 @@
 		size = min_t(u32, loi->size, SZ_16M);
 	}
 
-	path = btrfs_alloc_path();
-	if (!path) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
 	inodes = init_data_container(size);
 	if (IS_ERR(inodes)) {
 		ret = PTR_ERR(inodes);
-		inodes = NULL;
-		goto out;
+		goto out_loi;
 	}
 
+	path = btrfs_alloc_path();
+	if (!path) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	ret = iterate_inodes_from_logical(loi->logical, fs_info, path,
-					  build_ino_list, inodes, ignore_offset);
+					  inodes, ignore_offset);
+	btrfs_free_path(path);
 	if (ret == -EINVAL)
 		ret = -ENOENT;
 	if (ret < 0)
@@ -3979,7 +3995,6 @@
 		ret = -EFAULT;
 
 out:
-	btrfs_free_path(path);
 	kvfree(inodes);
 out_loi:
 	kfree(loi);
@@ -4279,7 +4294,9 @@
 	}
 
 	/* update qgroup status and info */
+	mutex_lock(&fs_info->qgroup_ioctl_lock);
 	err = btrfs_run_qgroups(trans);
+	mutex_unlock(&fs_info->qgroup_ioctl_lock);
 	if (err < 0)
 		btrfs_handle_fs_error(fs_info, err,
 				      "failed to update qgroup status and info");
@@ -4321,6 +4338,11 @@
 		goto out;
 	}
 
+	if (sa->create && is_fstree(sa->qgroupid)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	trans = btrfs_join_transaction(root);
 	if (IS_ERR(trans)) {
 		ret = PTR_ERR(trans);
@@ -4866,7 +4888,7 @@
 
 	if (compat) {
 #if defined(CONFIG_64BIT) && defined(CONFIG_COMPAT)
-		struct btrfs_ioctl_send_args_32 args32;
+		struct btrfs_ioctl_send_args_32 args32 = { 0 };
 
 		ret = copy_from_user(&args32, argp, sizeof(args32));
 		if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/locking.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/locking.c
@@ -14,6 +14,93 @@
 #include "locking.h"
 
 /*
+ * Lockdep class keys for extent_buffer->lock's in this root.  For a given
+ * eb, the lockdep key is determined by the btrfs_root it belongs to and
+ * the level the eb occupies in the tree.
+ *
+ * Different roots are used for different purposes and may nest inside each
+ * other and they require separate keysets.  As lockdep keys should be
+ * static, assign keysets according to the purpose of the root as indicated
+ * by btrfs_root->root_key.objectid.  This ensures that all special purpose
+ * roots have separate keysets.
+ *
+ * Lock-nesting across peer nodes is always done with the immediate parent
+ * node locked thus preventing deadlock.  As lockdep doesn't know this, use
+ * subclass to avoid triggering lockdep warning in such cases.
+ *
+ * The key is set by the readpage_end_io_hook after the buffer has passed
+ * csum validation but before the pages are unlocked.  It is also set by
+ * btrfs_init_new_buffer on freshly allocated blocks.
+ *
+ * We also add a check to make sure the highest level of the tree is the
+ * same as our lockdep setup here.  If BTRFS_MAX_LEVEL changes, this code
+ * needs update as well.
+ */
+#ifdef CONFIG_DEBUG_LOCK_ALLOC
+#if BTRFS_MAX_LEVEL != 8
+#error
+#endif
+
+#define DEFINE_LEVEL(stem, level)					\
+	.names[level] = "btrfs-" stem "-0" #level,
+
+#define DEFINE_NAME(stem)						\
+	DEFINE_LEVEL(stem, 0)						\
+	DEFINE_LEVEL(stem, 1)						\
+	DEFINE_LEVEL(stem, 2)						\
+	DEFINE_LEVEL(stem, 3)						\
+	DEFINE_LEVEL(stem, 4)						\
+	DEFINE_LEVEL(stem, 5)						\
+	DEFINE_LEVEL(stem, 6)						\
+	DEFINE_LEVEL(stem, 7)
+
+static struct btrfs_lockdep_keyset {
+	u64			id;		/* root objectid */
+	/* Longest entry: btrfs-free-space-00 */
+	char			names[BTRFS_MAX_LEVEL][20];
+	struct lock_class_key	keys[BTRFS_MAX_LEVEL];
+} btrfs_lockdep_keysets[] = {
+	{ .id = BTRFS_ROOT_TREE_OBJECTID,	DEFINE_NAME("root")	},
+	{ .id = BTRFS_EXTENT_TREE_OBJECTID,	DEFINE_NAME("extent")	},
+	{ .id = BTRFS_CHUNK_TREE_OBJECTID,	DEFINE_NAME("chunk")	},
+	{ .id = BTRFS_DEV_TREE_OBJECTID,	DEFINE_NAME("dev")	},
+	{ .id = BTRFS_CSUM_TREE_OBJECTID,	DEFINE_NAME("csum")	},
+	{ .id = BTRFS_QUOTA_TREE_OBJECTID,	DEFINE_NAME("quota")	},
+	{ .id = BTRFS_TREE_LOG_OBJECTID,	DEFINE_NAME("log")	},
+	{ .id = BTRFS_TREE_RELOC_OBJECTID,	DEFINE_NAME("treloc")	},
+	{ .id = BTRFS_DATA_RELOC_TREE_OBJECTID,	DEFINE_NAME("dreloc")	},
+	{ .id = BTRFS_UUID_TREE_OBJECTID,	DEFINE_NAME("uuid")	},
+	{ .id = BTRFS_FREE_SPACE_TREE_OBJECTID,	DEFINE_NAME("free-space") },
+	{ .id = 0,				DEFINE_NAME("tree")	},
+};
+
+#undef DEFINE_LEVEL
+#undef DEFINE_NAME
+
+void btrfs_set_buffer_lockdep_class(u64 objectid, struct extent_buffer *eb, int level)
+{
+	struct btrfs_lockdep_keyset *ks;
+
+	BUG_ON(level >= ARRAY_SIZE(ks->keys));
+
+	/* Find the matching keyset, id 0 is the default entry */
+	for (ks = btrfs_lockdep_keysets; ks->id; ks++)
+		if (ks->id == objectid)
+			break;
+
+	lockdep_set_class_and_name(&eb->lock, &ks->keys[level], ks->names[level]);
+}
+
+void btrfs_maybe_reset_lockdep_class(struct btrfs_root *root, struct extent_buffer *eb)
+{
+	if (test_bit(BTRFS_ROOT_RESET_LOCKDEP_CLASS, &root->state))
+		btrfs_set_buffer_lockdep_class(root->root_key.objectid,
+					       eb, btrfs_header_level(eb));
+}
+
+#endif
+
+/*
  * Extent buffer locking
  * =====================
  *
@@ -45,7 +132,6 @@
 		start_ns = ktime_get_ns();
 
 	down_read_nested(&eb->lock, nest);
-	eb->lock_owner = current->pid;
 	trace_btrfs_tree_read_lock(eb, start_ns);
 }
 
@@ -62,7 +148,6 @@
 int btrfs_try_tree_read_lock(struct extent_buffer *eb)
 {
 	if (down_read_trylock(&eb->lock)) {
-		eb->lock_owner = current->pid;
 		trace_btrfs_try_tree_read_lock(eb);
 		return 1;
 	}
@@ -90,7 +175,6 @@
 void btrfs_tree_read_unlock(struct extent_buffer *eb)
 {
 	trace_btrfs_tree_read_unlock(eb);
-	eb->lock_owner = 0;
 	up_read(&eb->lock);
 }
 
@@ -167,6 +251,8 @@
 
 	while (1) {
 		eb = btrfs_root_node(root);
+
+		btrfs_maybe_reset_lockdep_class(root, eb);
 		btrfs_tree_lock(eb);
 		if (eb == root->node)
 			break;
@@ -188,6 +274,8 @@
 
 	while (1) {
 		eb = btrfs_root_node(root);
+
+		btrfs_maybe_reset_lockdep_class(root, eb);
 		btrfs_tree_read_lock(eb);
 		if (eb == root->node)
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/locking.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/locking.h
@@ -130,4 +130,18 @@
 void btrfs_drew_read_lock(struct btrfs_drew_lock *lock);
 void btrfs_drew_read_unlock(struct btrfs_drew_lock *lock);
 
+#ifdef CONFIG_DEBUG_LOCK_ALLOC
+void btrfs_set_buffer_lockdep_class(u64 objectid, struct extent_buffer *eb, int level);
+void btrfs_maybe_reset_lockdep_class(struct btrfs_root *root, struct extent_buffer *eb);
+#else
+static inline void btrfs_set_buffer_lockdep_class(u64 objectid,
+					struct extent_buffer *eb, int level)
+{
+}
+static inline void btrfs_maybe_reset_lockdep_class(struct btrfs_root *root,
+						   struct extent_buffer *eb)
+{
+}
+#endif
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/lzo.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/lzo.c
@@ -357,11 +357,23 @@
 		ASSERT(cur_in / sectorsize ==
 		       (cur_in + LZO_LEN - 1) / sectorsize);
 		cur_page = cb->compressed_pages[cur_in / PAGE_SIZE];
-		kaddr = kmap(cur_page);
 		ASSERT(cur_page);
+		kaddr = kmap(cur_page);
 		seg_len = read_compress_length(kaddr + offset_in_page(cur_in));
+		kunmap(cur_page);
 		cur_in += LZO_LEN;
 
+		if (seg_len > lzo1x_worst_compress(PAGE_SIZE)) {
+			/*
+			 * seg_len shouldn't be larger than we have allocated
+			 * for workspace->cbuf
+			 */
+			btrfs_err(fs_info, "unexpectedly large lzo segment len %u",
+					seg_len);
+			ret = -EIO;
+			goto out;
+		}
+
 		/* Copy the compressed segment payload into workspace */
 		copy_compressed_segment(cb, workspace->cbuf, seg_len, &cur_in);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/print-tree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/print-tree.c
@@ -147,10 +147,10 @@
 			pr_cont("shared data backref parent %llu count %u\n",
 			       offset, btrfs_shared_data_ref_count(eb, sref));
 			/*
-			 * offset is supposed to be a tree block which
-			 * must be aligned to nodesize.
+			 * Offset is supposed to be a tree block which must be
+			 * aligned to sectorsize.
 			 */
-			if (!IS_ALIGNED(offset, eb->fs_info->nodesize))
+			if (!IS_ALIGNED(offset, eb->fs_info->sectorsize))
 				pr_info(
 			"\t\t\t(parent %llu not aligned to sectorsize %u)\n",
 				     offset, eb->fs_info->sectorsize);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/qgroup.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/qgroup.c
@@ -940,6 +940,14 @@
 	int ret = 0;
 	int slot;
 
+	/*
+	 * We need to have subvol_sem write locked, to prevent races between
+	 * concurrent tasks trying to enable quotas, because we will unlock
+	 * and relock qgroup_ioctl_lock before setting fs_info->quota_root
+	 * and before setting BTRFS_FS_QUOTA_ENABLED.
+	 */
+	lockdep_assert_held_write(&fs_info->subvol_sem);
+
 	mutex_lock(&fs_info->qgroup_ioctl_lock);
 	if (fs_info->quota_root)
 		goto out;
@@ -1117,8 +1125,19 @@
 		goto out_free_path;
 	}
 
+	mutex_unlock(&fs_info->qgroup_ioctl_lock);
+	/*
+	 * Commit the transaction while not holding qgroup_ioctl_lock, to avoid
+	 * a deadlock with tasks concurrently doing other qgroup operations, such
+	 * adding/removing qgroups or adding/deleting qgroup relations for example,
+	 * because all qgroup operations first start or join a transaction and then
+	 * lock the qgroup_ioctl_lock mutex.
+	 * We are safe from a concurrent task trying to enable quotas, by calling
+	 * this function, since we are serialized by fs_info->subvol_sem.
+	 */
 	ret = btrfs_commit_transaction(trans);
 	trans = NULL;
+	mutex_lock(&fs_info->qgroup_ioctl_lock);
 	if (ret)
 		goto out_free_path;
 
@@ -1138,6 +1157,21 @@
 		fs_info->qgroup_rescan_running = true;
 	        btrfs_queue_work(fs_info->qgroup_rescan_workers,
 	                         &fs_info->qgroup_rescan_work);
+	} else {
+		/*
+		 * We have set both BTRFS_FS_QUOTA_ENABLED and
+		 * BTRFS_QGROUP_STATUS_FLAG_ON, so we can only fail with
+		 * -EINPROGRESS. That can happen because someone started the
+		 * rescan worker by calling quota rescan ioctl before we
+		 * attempted to initialize the rescan worker. Failure due to
+		 * quotas disabled in the meanwhile is not possible, because
+		 * we are holding a write lock on fs_info->subvol_sem, which
+		 * is also acquired when disabling quotas.
+		 * Ignore such error, and any other error would need to undo
+		 * everything we did in the transaction we just committed.
+		 */
+		ASSERT(ret == -EINPROGRESS);
+		ret = 0;
 	}
 
 out_free_path:
@@ -1162,16 +1196,49 @@
 
 int btrfs_quota_disable(struct btrfs_fs_info *fs_info)
 {
-	struct btrfs_root *quota_root;
+	struct btrfs_root *quota_root = NULL;
 	struct btrfs_trans_handle *trans = NULL;
 	int ret = 0;
 
+	/*
+	 * We need to have subvol_sem write locked to prevent races with
+	 * snapshot creation.
+	 */
+	lockdep_assert_held_write(&fs_info->subvol_sem);
+
+	/*
+	 * Lock the cleaner mutex to prevent races with concurrent relocation,
+	 * because relocation may be building backrefs for blocks of the quota
+	 * root while we are deleting the root. This is like dropping fs roots
+	 * of deleted snapshots/subvolumes, we need the same protection.
+	 *
+	 * This also prevents races between concurrent tasks trying to disable
+	 * quotas, because we will unlock and relock qgroup_ioctl_lock across
+	 * BTRFS_FS_QUOTA_ENABLED changes.
+	 */
+	mutex_lock(&fs_info->cleaner_mutex);
+
 	mutex_lock(&fs_info->qgroup_ioctl_lock);
 	if (!fs_info->quota_root)
 		goto out;
+
+	/*
+	 * Unlock the qgroup_ioctl_lock mutex before waiting for the rescan worker to
+	 * complete. Otherwise we can deadlock because btrfs_remove_qgroup() needs
+	 * to lock that mutex while holding a transaction handle and the rescan
+	 * worker needs to commit a transaction.
+	 */
 	mutex_unlock(&fs_info->qgroup_ioctl_lock);
 
 	/*
+	 * Request qgroup rescan worker to complete and wait for it. This wait
+	 * must be done before transaction start for quota disable since it may
+	 * deadlock with transaction by the qgroup rescan worker.
+	 */
+	clear_bit(BTRFS_FS_QUOTA_ENABLED, &fs_info->flags);
+	btrfs_qgroup_wait_for_completion(fs_info, false);
+
+	/*
 	 * 1 For the root item
 	 *
 	 * We should also reserve enough items for the quota tree deletion in
@@ -1186,14 +1253,13 @@
 	if (IS_ERR(trans)) {
 		ret = PTR_ERR(trans);
 		trans = NULL;
+		set_bit(BTRFS_FS_QUOTA_ENABLED, &fs_info->flags);
 		goto out;
 	}
 
 	if (!fs_info->quota_root)
 		goto out;
 
-	clear_bit(BTRFS_FS_QUOTA_ENABLED, &fs_info->flags);
-	btrfs_qgroup_wait_for_completion(fs_info, false);
 	spin_lock(&fs_info->qgroup_lock);
 	quota_root = fs_info->quota_root;
 	fs_info->quota_root = NULL;
@@ -1214,21 +1280,25 @@
 		goto out;
 	}
 
+	spin_lock(&fs_info->trans_lock);
 	list_del(&quota_root->dirty_list);
+	spin_unlock(&fs_info->trans_lock);
 
 	btrfs_tree_lock(quota_root->node);
 	btrfs_clean_tree_block(quota_root->node);
 	btrfs_tree_unlock(quota_root->node);
-	btrfs_free_tree_block(trans, quota_root, quota_root->node, 0, 1);
+	btrfs_free_tree_block(trans, btrfs_root_id(quota_root),
+			      quota_root->node, 0, 1);
 
-	btrfs_put_root(quota_root);
 
 out:
+	btrfs_put_root(quota_root);
 	mutex_unlock(&fs_info->qgroup_ioctl_lock);
 	if (ret && trans)
 		btrfs_end_transaction(trans);
 	else if (trans)
 		ret = btrfs_end_transaction(trans);
+	mutex_unlock(&fs_info->cleaner_mutex);
 
 	return ret;
 }
@@ -1538,6 +1608,15 @@
 	return ret;
 }
 
+static bool qgroup_has_usage(struct btrfs_qgroup *qgroup)
+{
+	return (qgroup->rfer > 0 || qgroup->rfer_cmpr > 0 ||
+		qgroup->excl > 0 || qgroup->excl_cmpr > 0 ||
+		qgroup->rsv.values[BTRFS_QGROUP_RSV_DATA] > 0 ||
+		qgroup->rsv.values[BTRFS_QGROUP_RSV_META_PREALLOC] > 0 ||
+		qgroup->rsv.values[BTRFS_QGROUP_RSV_META_PERTRANS] > 0);
+}
+
 int btrfs_remove_qgroup(struct btrfs_trans_handle *trans, u64 qgroupid)
 {
 	struct btrfs_fs_info *fs_info = trans->fs_info;
@@ -1557,6 +1636,11 @@
 		goto out;
 	}
 
+	if (is_fstree(qgroupid) && qgroup_has_usage(qgroup)) {
+		ret = -EBUSY;
+		goto out;
+	}
+
 	/* Check if there are no children of this qgroup */
 	if (!list_empty(&qgroup->members)) {
 		ret = -EBUSY;
@@ -2564,8 +2648,6 @@
 	if (nr_old_roots == 0 && nr_new_roots == 0)
 		goto out_free;
 
-	BUG_ON(!fs_info->quota_root);
-
 	trace_btrfs_qgroup_account_extent(fs_info, trans->transid, bytenr,
 					num_bytes, nr_old_roots, nr_new_roots);
 
@@ -2696,13 +2778,22 @@
 }
 
 /*
- * called from commit_transaction. Writes all changed qgroups to disk.
+ * Writes all changed qgroups to disk.
+ * Called by the transaction commit path and the qgroup assign ioctl.
  */
 int btrfs_run_qgroups(struct btrfs_trans_handle *trans)
 {
 	struct btrfs_fs_info *fs_info = trans->fs_info;
 	int ret = 0;
 
+	/*
+	 * In case we are called from the qgroup assign ioctl, assert that we
+	 * are holding the qgroup_ioctl_lock, otherwise we can race with a quota
+	 * disable operation (ioctl) and access a freed quota root.
+	 */
+	if (trans->transaction->state != TRANS_STATE_COMMIT_DOING)
+		lockdep_assert_held(&fs_info->qgroup_ioctl_lock);
+
 	if (!fs_info->quota_root)
 		return ret;
 
@@ -2847,14 +2938,7 @@
 		dstgroup->rsv_rfer = inherit->lim.rsv_rfer;
 		dstgroup->rsv_excl = inherit->lim.rsv_excl;
 
-		ret = update_qgroup_limit_item(trans, dstgroup);
-		if (ret) {
-			fs_info->qgroup_flags |= BTRFS_QGROUP_STATUS_FLAG_INCONSISTENT;
-			btrfs_info(fs_info,
-				   "unable to update quota limit for %llu",
-				   dstgroup->qgroupid);
-			goto unlock;
-		}
+		qgroup_dirty(fs_info, dstgroup);
 	}
 
 	if (srcid) {
@@ -3224,7 +3308,8 @@
 static bool rescan_should_stop(struct btrfs_fs_info *fs_info)
 {
 	return btrfs_fs_closing(fs_info) ||
-		test_bit(BTRFS_FS_STATE_REMOUNTING, &fs_info->fs_state);
+		test_bit(BTRFS_FS_STATE_REMOUNTING, &fs_info->fs_state) ||
+		!test_bit(BTRFS_FS_QUOTA_ENABLED, &fs_info->flags);
 }
 
 static void btrfs_qgroup_rescan_worker(struct btrfs_work *work)
@@ -3236,6 +3321,7 @@
 	int err = -ENOMEM;
 	int ret = 0;
 	bool stopped = false;
+	bool did_leaf_rescans = false;
 
 	path = btrfs_alloc_path();
 	if (!path)
@@ -3254,11 +3340,10 @@
 			err = PTR_ERR(trans);
 			break;
 		}
-		if (!test_bit(BTRFS_FS_QUOTA_ENABLED, &fs_info->flags)) {
-			err = -EINTR;
-		} else {
-			err = qgroup_rescan_leaf(trans, path);
-		}
+
+		err = qgroup_rescan_leaf(trans, path);
+		did_leaf_rescans = true;
+
 		if (err > 0)
 			btrfs_commit_transaction(trans);
 		else
@@ -3272,22 +3357,29 @@
 	if (err > 0 &&
 	    fs_info->qgroup_flags & BTRFS_QGROUP_STATUS_FLAG_INCONSISTENT) {
 		fs_info->qgroup_flags &= ~BTRFS_QGROUP_STATUS_FLAG_INCONSISTENT;
-	} else if (err < 0) {
+	} else if (err < 0 || stopped) {
 		fs_info->qgroup_flags |= BTRFS_QGROUP_STATUS_FLAG_INCONSISTENT;
 	}
 	mutex_unlock(&fs_info->qgroup_rescan_lock);
 
 	/*
-	 * only update status, since the previous part has already updated the
-	 * qgroup info.
+	 * Only update status, since the previous part has already updated the
+	 * qgroup info, and only if we did any actual work. This also prevents
+	 * race with a concurrent quota disable, which has already set
+	 * fs_info->quota_root to NULL and cleared BTRFS_FS_QUOTA_ENABLED at
+	 * btrfs_quota_disable().
 	 */
-	trans = btrfs_start_transaction(fs_info->quota_root, 1);
-	if (IS_ERR(trans)) {
-		err = PTR_ERR(trans);
+	if (did_leaf_rescans) {
+		trans = btrfs_start_transaction(fs_info->quota_root, 1);
+		if (IS_ERR(trans)) {
+			err = PTR_ERR(trans);
+			trans = NULL;
+			btrfs_err(fs_info,
+				  "fail to start transaction for status update: %d",
+				  err);
+		}
+	} else {
 		trans = NULL;
-		btrfs_err(fs_info,
-			  "fail to start transaction for status update: %d",
-			  err);
 	}
 
 	mutex_lock(&fs_info->qgroup_rescan_lock);
@@ -3360,6 +3452,9 @@
 			btrfs_warn(fs_info,
 			"qgroup rescan init failed, qgroup is not enabled");
 			ret = -EINVAL;
+		} else if (!test_bit(BTRFS_FS_QUOTA_ENABLED, &fs_info->flags)) {
+			/* Quota disable is in progress */
+			ret = -EBUSY;
 		}
 
 		if (ret) {
@@ -3582,6 +3677,8 @@
 		return 0;
 	}
 
+	btrfs_run_delayed_iputs(root->fs_info);
+	btrfs_wait_on_delayed_iputs(root->fs_info);
 	ret = btrfs_start_delalloc_snapshot(root, true);
 	if (ret < 0)
 		goto out;
@@ -3983,6 +4080,8 @@
 				      BTRFS_QGROUP_RSV_META_PREALLOC);
 	trace_qgroup_meta_convert(root, num_bytes);
 	qgroup_convert_meta(fs_info, root->root_key.objectid, num_bytes);
+	if (!sb_rdonly(fs_info->sb))
+		add_root_meta_rsv(root, num_bytes, BTRFS_QGROUP_RSV_META_PERTRANS);
 }
 
 /*
@@ -4271,4 +4370,5 @@
 		ulist_free(entry->old_roots);
 		kfree(entry);
 	}
+	*root = RB_ROOT;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/raid56.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/raid56.c
@@ -61,7 +61,7 @@
 
 struct btrfs_raid_bio {
 	struct btrfs_fs_info *fs_info;
-	struct btrfs_bio *bbio;
+	struct btrfs_io_context *bioc;
 
 	/* while we're doing rmw on a stripe
 	 * we put it into a hash table so we can
@@ -271,7 +271,7 @@
  */
 static int rbio_bucket(struct btrfs_raid_bio *rbio)
 {
-	u64 num = rbio->bbio->raid_map[0];
+	u64 num = rbio->bioc->raid_map[0];
 
 	/*
 	 * we shift down quite a bit.  We're using byte
@@ -324,6 +324,9 @@
 {
 	bio_list_merge(&dest->bio_list, &victim->bio_list);
 	dest->bio_list_bytes += victim->bio_list_bytes;
+	/* Also inherit the bitmaps from @victim. */
+	bitmap_or(dest->dbitmap, victim->dbitmap, dest->dbitmap,
+		  dest->stripe_npages);
 	dest->generic_bio_cnt += victim->generic_bio_cnt;
 	bio_list_init(&victim->bio_list);
 }
@@ -559,8 +562,7 @@
 	    test_bit(RBIO_CACHE_BIT, &cur->flags))
 		return 0;
 
-	if (last->bbio->raid_map[0] !=
-	    cur->bbio->raid_map[0])
+	if (last->bioc->raid_map[0] != cur->bioc->raid_map[0])
 		return 0;
 
 	/* we can't merge with different operations */
@@ -673,7 +675,7 @@
 
 	spin_lock_irqsave(&h->lock, flags);
 	list_for_each_entry(cur, &h->hash_list, hash_list) {
-		if (cur->bbio->raid_map[0] != rbio->bbio->raid_map[0])
+		if (cur->bioc->raid_map[0] != rbio->bioc->raid_map[0])
 			continue;
 
 		spin_lock(&cur->bio_list_lock);
@@ -838,7 +840,7 @@
 		}
 	}
 
-	btrfs_put_bbio(rbio->bbio);
+	btrfs_put_bioc(rbio->bioc);
 	kfree(rbio);
 }
 
@@ -866,6 +868,12 @@
 
 	if (rbio->generic_bio_cnt)
 		btrfs_bio_counter_sub(rbio->fs_info, rbio->generic_bio_cnt);
+	/*
+	 * Clear the data bitmap, as the rbio may be cached for later usage.
+	 * do this before before unlock_stripe() so there will be no new bio
+	 * for this bio.
+	 */
+	bitmap_clear(rbio->dbitmap, 0, rbio->stripe_npages);
 
 	/*
 	 * At this moment, rbio->bio_list is empty, however since rbio does not
@@ -906,7 +914,7 @@
 
 	/* OK, we have read all the stripes we need to. */
 	max_errors = (rbio->operation == BTRFS_RBIO_PARITY_SCRUB) ?
-		     0 : rbio->bbio->max_errors;
+		     0 : rbio->bioc->max_errors;
 	if (atomic_read(&rbio->error) > max_errors)
 		err = BLK_STS_IOERR;
 
@@ -961,12 +969,12 @@
  * this does not allocate any pages for rbio->pages.
  */
 static struct btrfs_raid_bio *alloc_rbio(struct btrfs_fs_info *fs_info,
-					 struct btrfs_bio *bbio,
+					 struct btrfs_io_context *bioc,
 					 u64 stripe_len)
 {
 	struct btrfs_raid_bio *rbio;
 	int nr_data = 0;
-	int real_stripes = bbio->num_stripes - bbio->num_tgtdevs;
+	int real_stripes = bioc->num_stripes - bioc->num_tgtdevs;
 	int num_pages = rbio_nr_pages(stripe_len, real_stripes);
 	int stripe_npages = DIV_ROUND_UP(stripe_len, PAGE_SIZE);
 	void *p;
@@ -987,7 +995,7 @@
 	spin_lock_init(&rbio->bio_list_lock);
 	INIT_LIST_HEAD(&rbio->stripe_cache);
 	INIT_LIST_HEAD(&rbio->hash_list);
-	rbio->bbio = bbio;
+	rbio->bioc = bioc;
 	rbio->fs_info = fs_info;
 	rbio->stripe_len = stripe_len;
 	rbio->nr_pages = num_pages;
@@ -1015,9 +1023,9 @@
 	CONSUME_ALLOC(rbio->finish_pbitmap, BITS_TO_LONGS(stripe_npages));
 #undef  CONSUME_ALLOC
 
-	if (bbio->map_type & BTRFS_BLOCK_GROUP_RAID5)
+	if (bioc->map_type & BTRFS_BLOCK_GROUP_RAID5)
 		nr_data = real_stripes - 1;
-	else if (bbio->map_type & BTRFS_BLOCK_GROUP_RAID6)
+	else if (bioc->map_type & BTRFS_BLOCK_GROUP_RAID6)
 		nr_data = real_stripes - 2;
 	else
 		BUG();
@@ -1077,10 +1085,10 @@
 	struct bio *last = bio_list->tail;
 	int ret;
 	struct bio *bio;
-	struct btrfs_bio_stripe *stripe;
+	struct btrfs_io_stripe *stripe;
 	u64 disk_start;
 
-	stripe = &rbio->bbio->stripes[stripe_nr];
+	stripe = &rbio->bioc->stripes[stripe_nr];
 	disk_start = stripe->physical + (page_index << PAGE_SHIFT);
 
 	/* if the device is missing, just fail this stripe */
@@ -1155,7 +1163,7 @@
 		int i = 0;
 
 		start = bio->bi_iter.bi_sector << 9;
-		stripe_offset = start - rbio->bbio->raid_map[0];
+		stripe_offset = start - rbio->bioc->raid_map[0];
 		page_index = stripe_offset >> PAGE_SHIFT;
 
 		if (bio_flagged(bio, BIO_CLONED))
@@ -1179,7 +1187,7 @@
  */
 static noinline void finish_rmw(struct btrfs_raid_bio *rbio)
 {
-	struct btrfs_bio *bbio = rbio->bbio;
+	struct btrfs_io_context *bioc = rbio->bioc;
 	void **pointers = rbio->finish_pointers;
 	int nr_data = rbio->nr_data;
 	int stripe;
@@ -1198,6 +1206,9 @@
 	else
 		BUG();
 
+	/* We should have at least one data sector. */
+	ASSERT(bitmap_weight(rbio->dbitmap, rbio->stripe_npages));
+
 	/* at this point we either have a full stripe,
 	 * or we've read the full stripe from the drive.
 	 * recalculate the parity and write the new results.
@@ -1269,6 +1280,11 @@
 	for (stripe = 0; stripe < rbio->real_stripes; stripe++) {
 		for (pagenr = 0; pagenr < rbio->stripe_npages; pagenr++) {
 			struct page *page;
+
+			/* This vertical stripe has no data, skip it. */
+			if (!test_bit(pagenr, rbio->dbitmap))
+				continue;
+
 			if (stripe < rbio->nr_data) {
 				page = page_in_rbio(rbio, stripe, pagenr, 1);
 				if (!page)
@@ -1284,15 +1300,20 @@
 		}
 	}
 
-	if (likely(!bbio->num_tgtdevs))
+	if (likely(!bioc->num_tgtdevs))
 		goto write_data;
 
 	for (stripe = 0; stripe < rbio->real_stripes; stripe++) {
-		if (!bbio->tgtdev_map[stripe])
+		if (!bioc->tgtdev_map[stripe])
 			continue;
 
 		for (pagenr = 0; pagenr < rbio->stripe_npages; pagenr++) {
 			struct page *page;
+
+			/* This vertical stripe has no data, skip it. */
+			if (!test_bit(pagenr, rbio->dbitmap))
+				continue;
+
 			if (stripe < rbio->nr_data) {
 				page = page_in_rbio(rbio, stripe, pagenr, 1);
 				if (!page)
@@ -1302,7 +1323,7 @@
 			}
 
 			ret = rbio_add_io_page(rbio, &bio_list, page,
-					       rbio->bbio->tgtdev_map[stripe],
+					       rbio->bioc->tgtdev_map[stripe],
 					       pagenr, rbio->stripe_len);
 			if (ret)
 				goto cleanup;
@@ -1339,12 +1360,12 @@
 {
 	u64 physical = bio->bi_iter.bi_sector;
 	int i;
-	struct btrfs_bio_stripe *stripe;
+	struct btrfs_io_stripe *stripe;
 
 	physical <<= 9;
 
-	for (i = 0; i < rbio->bbio->num_stripes; i++) {
-		stripe = &rbio->bbio->stripes[i];
+	for (i = 0; i < rbio->bioc->num_stripes; i++) {
+		stripe = &rbio->bioc->stripes[i];
 		if (in_range(physical, stripe->physical, rbio->stripe_len) &&
 		    stripe->dev->bdev && bio->bi_bdev == stripe->dev->bdev) {
 			return i;
@@ -1365,7 +1386,7 @@
 	int i;
 
 	for (i = 0; i < rbio->nr_data; i++) {
-		u64 stripe_start = rbio->bbio->raid_map[i];
+		u64 stripe_start = rbio->bioc->raid_map[i];
 
 		if (in_range(logical, stripe_start, rbio->stripe_len))
 			return i;
@@ -1456,7 +1477,7 @@
 	if (!atomic_dec_and_test(&rbio->stripes_pending))
 		return;
 
-	if (atomic_read(&rbio->error) > rbio->bbio->max_errors)
+	if (atomic_read(&rbio->error) > rbio->bioc->max_errors)
 		goto cleanup;
 
 	/*
@@ -1538,8 +1559,8 @@
 	}
 
 	/*
-	 * the bbio may be freed once we submit the last bio.  Make sure
-	 * not to touch it after that
+	 * The bioc may be freed once we submit the last bio. Make sure not to
+	 * touch it after that.
 	 */
 	atomic_set(&rbio->stripes_pending, bios_to_read);
 	while ((bio = bio_list_pop(&bio_list))) {
@@ -1716,25 +1737,51 @@
 	run_plug(plug);
 }
 
+/* Add the original bio into rbio->bio_list, and update rbio::dbitmap. */
+static void rbio_add_bio(struct btrfs_raid_bio *rbio, struct bio *orig_bio)
+{
+	const struct btrfs_fs_info *fs_info = rbio->fs_info;
+	const u64 orig_logical = orig_bio->bi_iter.bi_sector << SECTOR_SHIFT;
+	const u64 full_stripe_start = rbio->bioc->raid_map[0];
+	const u32 orig_len = orig_bio->bi_iter.bi_size;
+	const u32 sectorsize = fs_info->sectorsize;
+	u64 cur_logical;
+
+	ASSERT(orig_logical >= full_stripe_start &&
+	       orig_logical + orig_len <= full_stripe_start +
+	       rbio->nr_data * rbio->stripe_len);
+
+	bio_list_add(&rbio->bio_list, orig_bio);
+	rbio->bio_list_bytes += orig_bio->bi_iter.bi_size;
+
+	/* Update the dbitmap. */
+	for (cur_logical = orig_logical; cur_logical < orig_logical + orig_len;
+	     cur_logical += sectorsize) {
+		int bit = ((u32)(cur_logical - full_stripe_start) >>
+			   fs_info->sectorsize_bits) % rbio->stripe_npages;
+
+		set_bit(bit, rbio->dbitmap);
+	}
+}
+
 /*
  * our main entry point for writes from the rest of the FS.
  */
 int raid56_parity_write(struct btrfs_fs_info *fs_info, struct bio *bio,
-			struct btrfs_bio *bbio, u64 stripe_len)
+			struct btrfs_io_context *bioc, u64 stripe_len)
 {
 	struct btrfs_raid_bio *rbio;
 	struct btrfs_plug_cb *plug = NULL;
 	struct blk_plug_cb *cb;
 	int ret;
 
-	rbio = alloc_rbio(fs_info, bbio, stripe_len);
+	rbio = alloc_rbio(fs_info, bioc, stripe_len);
 	if (IS_ERR(rbio)) {
-		btrfs_put_bbio(bbio);
+		btrfs_put_bioc(bioc);
 		return PTR_ERR(rbio);
 	}
-	bio_list_add(&rbio->bio_list, bio);
-	rbio->bio_list_bytes = bio->bi_iter.bi_size;
 	rbio->operation = BTRFS_RBIO_WRITE;
+	rbio_add_bio(rbio, bio);
 
 	btrfs_bio_counter_inc_noblocked(fs_info);
 	rbio->generic_bio_cnt = 1;
@@ -1842,7 +1889,7 @@
 		}
 
 		/* all raid6 handling here */
-		if (rbio->bbio->map_type & BTRFS_BLOCK_GROUP_RAID6) {
+		if (rbio->bioc->map_type & BTRFS_BLOCK_GROUP_RAID6) {
 			/*
 			 * single failure, rebuild from parity raid5
 			 * style
@@ -1874,8 +1921,8 @@
 			 * here due to a crc mismatch and we can't give them the
 			 * data they want
 			 */
-			if (rbio->bbio->raid_map[failb] == RAID6_Q_STRIPE) {
-				if (rbio->bbio->raid_map[faila] ==
+			if (rbio->bioc->raid_map[failb] == RAID6_Q_STRIPE) {
+				if (rbio->bioc->raid_map[faila] ==
 				    RAID5_P_STRIPE) {
 					err = BLK_STS_IOERR;
 					goto cleanup;
@@ -1887,7 +1934,7 @@
 				goto pstripe;
 			}
 
-			if (rbio->bbio->raid_map[failb] == RAID5_P_STRIPE) {
+			if (rbio->bioc->raid_map[failb] == RAID5_P_STRIPE) {
 				raid6_datap_recov(rbio->real_stripes,
 						  PAGE_SIZE, faila, pointers);
 			} else {
@@ -2006,7 +2053,7 @@
 	if (!atomic_dec_and_test(&rbio->stripes_pending))
 		return;
 
-	if (atomic_read(&rbio->error) > rbio->bbio->max_errors)
+	if (atomic_read(&rbio->error) > rbio->bioc->max_errors)
 		rbio_orig_end_io(rbio, BLK_STS_IOERR);
 	else
 		__raid_recover_end_io(rbio);
@@ -2038,9 +2085,12 @@
 	atomic_set(&rbio->error, 0);
 
 	/*
-	 * read everything that hasn't failed.  Thanks to the
-	 * stripe cache, it is possible that some or all of these
-	 * pages are going to be uptodate.
+	 * Read everything that hasn't failed. However this time we will
+	 * not trust any cached sector.
+	 * As we may read out some stale data but higher layer is not reading
+	 * that stale part.
+	 *
+	 * So here we always re-read everything in recovery path.
 	 */
 	for (stripe = 0; stripe < rbio->real_stripes; stripe++) {
 		if (rbio->faila == stripe || rbio->failb == stripe) {
@@ -2049,16 +2099,6 @@
 		}
 
 		for (pagenr = 0; pagenr < rbio->stripe_npages; pagenr++) {
-			struct page *p;
-
-			/*
-			 * the rmw code may have already read this
-			 * page in
-			 */
-			p = rbio_stripe_page(rbio, stripe, pagenr);
-			if (PageUptodate(p))
-				continue;
-
 			ret = rbio_add_io_page(rbio, &bio_list,
 				       rbio_stripe_page(rbio, stripe, pagenr),
 				       stripe, pagenr, rbio->stripe_len);
@@ -2074,7 +2114,7 @@
 		 * were up to date, or we might have no bios to read because
 		 * the devices were gone.
 		 */
-		if (atomic_read(&rbio->error) <= rbio->bbio->max_errors) {
+		if (atomic_read(&rbio->error) <= rbio->bioc->max_errors) {
 			__raid_recover_end_io(rbio);
 			return 0;
 		} else {
@@ -2083,8 +2123,8 @@
 	}
 
 	/*
-	 * the bbio may be freed once we submit the last bio.  Make sure
-	 * not to touch it after that
+	 * The bioc may be freed once we submit the last bio. Make sure not to
+	 * touch it after that.
 	 */
 	atomic_set(&rbio->stripes_pending, bios_to_read);
 	while ((bio = bio_list_pop(&bio_list))) {
@@ -2117,36 +2157,35 @@
  * of the drive.
  */
 int raid56_parity_recover(struct btrfs_fs_info *fs_info, struct bio *bio,
-			  struct btrfs_bio *bbio, u64 stripe_len,
+			  struct btrfs_io_context *bioc, u64 stripe_len,
 			  int mirror_num, int generic_io)
 {
 	struct btrfs_raid_bio *rbio;
 	int ret;
 
 	if (generic_io) {
-		ASSERT(bbio->mirror_num == mirror_num);
+		ASSERT(bioc->mirror_num == mirror_num);
 		btrfs_io_bio(bio)->mirror_num = mirror_num;
 	}
 
-	rbio = alloc_rbio(fs_info, bbio, stripe_len);
+	rbio = alloc_rbio(fs_info, bioc, stripe_len);
 	if (IS_ERR(rbio)) {
 		if (generic_io)
-			btrfs_put_bbio(bbio);
+			btrfs_put_bioc(bioc);
 		return PTR_ERR(rbio);
 	}
 
 	rbio->operation = BTRFS_RBIO_READ_REBUILD;
-	bio_list_add(&rbio->bio_list, bio);
-	rbio->bio_list_bytes = bio->bi_iter.bi_size;
+	rbio_add_bio(rbio, bio);
 
 	rbio->faila = find_logical_bio_stripe(rbio, bio);
 	if (rbio->faila == -1) {
 		btrfs_warn(fs_info,
-	"%s could not find the bad stripe in raid56 so that we cannot recover any more (bio has logical %llu len %llu, bbio has map_type %llu)",
+"%s could not find the bad stripe in raid56 so that we cannot recover any more (bio has logical %llu len %llu, bioc has map_type %llu)",
 			   __func__, bio->bi_iter.bi_sector << 9,
-			   (u64)bio->bi_iter.bi_size, bbio->map_type);
+			   (u64)bio->bi_iter.bi_size, bioc->map_type);
 		if (generic_io)
-			btrfs_put_bbio(bbio);
+			btrfs_put_bioc(bioc);
 		kfree(rbio);
 		return -EIO;
 	}
@@ -2155,7 +2194,7 @@
 		btrfs_bio_counter_inc_noblocked(fs_info);
 		rbio->generic_bio_cnt = 1;
 	} else {
-		btrfs_get_bbio(bbio);
+		btrfs_get_bioc(bioc);
 	}
 
 	/*
@@ -2214,7 +2253,7 @@
 /*
  * The following code is used to scrub/replace the parity stripe
  *
- * Caller must have already increased bio_counter for getting @bbio.
+ * Caller must have already increased bio_counter for getting @bioc.
  *
  * Note: We need make sure all the pages that add into the scrub/replace
  * raid bio are correct and not be changed during the scrub/replace. That
@@ -2223,14 +2262,14 @@
 
 struct btrfs_raid_bio *
 raid56_parity_alloc_scrub_rbio(struct btrfs_fs_info *fs_info, struct bio *bio,
-			       struct btrfs_bio *bbio, u64 stripe_len,
+			       struct btrfs_io_context *bioc, u64 stripe_len,
 			       struct btrfs_device *scrub_dev,
 			       unsigned long *dbitmap, int stripe_nsectors)
 {
 	struct btrfs_raid_bio *rbio;
 	int i;
 
-	rbio = alloc_rbio(fs_info, bbio, stripe_len);
+	rbio = alloc_rbio(fs_info, bioc, stripe_len);
 	if (IS_ERR(rbio))
 		return NULL;
 	bio_list_add(&rbio->bio_list, bio);
@@ -2242,12 +2281,12 @@
 	rbio->operation = BTRFS_RBIO_PARITY_SCRUB;
 
 	/*
-	 * After mapping bbio with BTRFS_MAP_WRITE, parities have been sorted
+	 * After mapping bioc with BTRFS_MAP_WRITE, parities have been sorted
 	 * to the end position, so this search can start from the first parity
 	 * stripe.
 	 */
 	for (i = rbio->nr_data; i < rbio->real_stripes; i++) {
-		if (bbio->stripes[i].dev == scrub_dev) {
+		if (bioc->stripes[i].dev == scrub_dev) {
 			rbio->scrubp = i;
 			break;
 		}
@@ -2260,7 +2299,7 @@
 	bitmap_copy(rbio->dbitmap, dbitmap, stripe_nsectors);
 
 	/*
-	 * We have already increased bio_counter when getting bbio, record it
+	 * We have already increased bio_counter when getting bioc, record it
 	 * so we can free it at rbio_orig_end_io().
 	 */
 	rbio->generic_bio_cnt = 1;
@@ -2275,10 +2314,10 @@
 	int stripe_offset;
 	int index;
 
-	ASSERT(logical >= rbio->bbio->raid_map[0]);
-	ASSERT(logical + PAGE_SIZE <= rbio->bbio->raid_map[0] +
+	ASSERT(logical >= rbio->bioc->raid_map[0]);
+	ASSERT(logical + PAGE_SIZE <= rbio->bioc->raid_map[0] +
 				rbio->stripe_len * rbio->nr_data);
-	stripe_offset = (int)(logical - rbio->bbio->raid_map[0]);
+	stripe_offset = (int)(logical - rbio->bioc->raid_map[0]);
 	index = stripe_offset >> PAGE_SHIFT;
 	rbio->bio_pages[index] = page;
 }
@@ -2312,7 +2351,7 @@
 static noinline void finish_parity_scrub(struct btrfs_raid_bio *rbio,
 					 int need_check)
 {
-	struct btrfs_bio *bbio = rbio->bbio;
+	struct btrfs_io_context *bioc = rbio->bioc;
 	void **pointers = rbio->finish_pointers;
 	unsigned long *pbitmap = rbio->finish_pbitmap;
 	int nr_data = rbio->nr_data;
@@ -2335,7 +2374,7 @@
 	else
 		BUG();
 
-	if (bbio->num_tgtdevs && bbio->tgtdev_map[rbio->scrubp]) {
+	if (bioc->num_tgtdevs && bioc->tgtdev_map[rbio->scrubp]) {
 		is_replace = 1;
 		bitmap_copy(pbitmap, rbio->dbitmap, rbio->stripe_npages);
 	}
@@ -2435,7 +2474,7 @@
 
 		page = rbio_stripe_page(rbio, rbio->scrubp, pagenr);
 		ret = rbio_add_io_page(rbio, &bio_list, page,
-				       bbio->tgtdev_map[rbio->scrubp],
+				       bioc->tgtdev_map[rbio->scrubp],
 				       pagenr, rbio->stripe_len);
 		if (ret)
 			goto cleanup;
@@ -2483,7 +2522,7 @@
  */
 static void validate_rbio_for_parity_scrub(struct btrfs_raid_bio *rbio)
 {
-	if (atomic_read(&rbio->error) > rbio->bbio->max_errors)
+	if (atomic_read(&rbio->error) > rbio->bioc->max_errors)
 		goto cleanup;
 
 	if (rbio->faila >= 0 || rbio->failb >= 0) {
@@ -2504,7 +2543,7 @@
 		 * the data, so the capability of the repair is declined.
 		 * (In the case of RAID5, we can not repair anything)
 		 */
-		if (dfail > rbio->bbio->max_errors - 1)
+		if (dfail > rbio->bioc->max_errors - 1)
 			goto cleanup;
 
 		/*
@@ -2625,8 +2664,8 @@
 	}
 
 	/*
-	 * the bbio may be freed once we submit the last bio.  Make sure
-	 * not to touch it after that
+	 * The bioc may be freed once we submit the last bio. Make sure not to
+	 * touch it after that.
 	 */
 	atomic_set(&rbio->stripes_pending, bios_to_read);
 	while ((bio = bio_list_pop(&bio_list))) {
@@ -2671,11 +2710,11 @@
 
 struct btrfs_raid_bio *
 raid56_alloc_missing_rbio(struct btrfs_fs_info *fs_info, struct bio *bio,
-			  struct btrfs_bio *bbio, u64 length)
+			  struct btrfs_io_context *bioc, u64 length)
 {
 	struct btrfs_raid_bio *rbio;
 
-	rbio = alloc_rbio(fs_info, bbio, length);
+	rbio = alloc_rbio(fs_info, bioc, length);
 	if (IS_ERR(rbio))
 		return NULL;
 
@@ -2689,13 +2728,15 @@
 
 	rbio->faila = find_logical_bio_stripe(rbio, bio);
 	if (rbio->faila == -1) {
-		BUG();
-		kfree(rbio);
+		btrfs_warn_rl(fs_info,
+	"can not determine the failed stripe number for full stripe %llu",
+			      bioc->raid_map[0]);
+		__free_raid_bio(rbio);
 		return NULL;
 	}
 
 	/*
-	 * When we get bbio, we have already increased bio_counter, record it
+	 * When we get bioc, we have already increased bio_counter, record it
 	 * so we can free it at rbio_orig_end_io()
 	 */
 	rbio->generic_bio_cnt = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/raid56.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/raid56.h
@@ -31,24 +31,24 @@
 struct btrfs_device;
 
 int raid56_parity_recover(struct btrfs_fs_info *fs_info, struct bio *bio,
-			  struct btrfs_bio *bbio, u64 stripe_len,
+			  struct btrfs_io_context *bioc, u64 stripe_len,
 			  int mirror_num, int generic_io);
 int raid56_parity_write(struct btrfs_fs_info *fs_info, struct bio *bio,
-			       struct btrfs_bio *bbio, u64 stripe_len);
+			struct btrfs_io_context *bioc, u64 stripe_len);
 
 void raid56_add_scrub_pages(struct btrfs_raid_bio *rbio, struct page *page,
 			    u64 logical);
 
 struct btrfs_raid_bio *
 raid56_parity_alloc_scrub_rbio(struct btrfs_fs_info *fs_info, struct bio *bio,
-			       struct btrfs_bio *bbio, u64 stripe_len,
+			       struct btrfs_io_context *bioc, u64 stripe_len,
 			       struct btrfs_device *scrub_dev,
 			       unsigned long *dbitmap, int stripe_nsectors);
 void raid56_parity_submit_scrub_rbio(struct btrfs_raid_bio *rbio);
 
 struct btrfs_raid_bio *
 raid56_alloc_missing_rbio(struct btrfs_fs_info *fs_info, struct bio *bio,
-			  struct btrfs_bio *bbio, u64 length);
+			  struct btrfs_io_context *bioc, u64 length);
 void raid56_submit_missing_rbio(struct btrfs_raid_bio *rbio);
 
 int btrfs_alloc_stripe_hash_table(struct btrfs_fs_info *info);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/rcu-string.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/rcu-string.h
@@ -18,7 +18,11 @@
 					 (len * sizeof(char)), mask);
 	if (!ret)
 		return ret;
-	strncpy(ret->str, src, len);
+	/* Warn if the source got unexpectedly truncated. */
+	if (WARN_ON(strscpy(ret->str, src, len) < 0)) {
+		kfree(ret);
+		return NULL;
+	}
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/reada.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/reada.c
@@ -227,7 +227,7 @@
 }
 
 static struct reada_zone *reada_find_zone(struct btrfs_device *dev, u64 logical,
-					  struct btrfs_bio *bbio)
+					  struct btrfs_io_context *bioc)
 {
 	struct btrfs_fs_info *fs_info = dev->fs_info;
 	int ret;
@@ -275,11 +275,11 @@
 	kref_init(&zone->refcnt);
 	zone->elems = 0;
 	zone->device = dev; /* our device always sits at index 0 */
-	for (i = 0; i < bbio->num_stripes; ++i) {
+	for (i = 0; i < bioc->num_stripes; ++i) {
 		/* bounds have already been checked */
-		zone->devs[i] = bbio->stripes[i].dev;
+		zone->devs[i] = bioc->stripes[i].dev;
 	}
-	zone->ndevs = bbio->num_stripes;
+	zone->ndevs = bioc->num_stripes;
 
 	spin_lock(&fs_info->reada_lock);
 	ret = radix_tree_insert(&dev->reada_zones,
@@ -309,7 +309,7 @@
 	int ret;
 	struct reada_extent *re = NULL;
 	struct reada_extent *re_exist = NULL;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	struct btrfs_device *dev;
 	struct btrfs_device *prev_dev;
 	u64 length;
@@ -345,28 +345,28 @@
 	 */
 	length = fs_info->nodesize;
 	ret = btrfs_map_block(fs_info, BTRFS_MAP_GET_READ_MIRRORS, logical,
-			&length, &bbio, 0);
-	if (ret || !bbio || length < fs_info->nodesize)
+			      &length, &bioc, 0);
+	if (ret || !bioc || length < fs_info->nodesize)
 		goto error;
 
-	if (bbio->num_stripes > BTRFS_MAX_MIRRORS) {
+	if (bioc->num_stripes > BTRFS_MAX_MIRRORS) {
 		btrfs_err(fs_info,
 			   "readahead: more than %d copies not supported",
 			   BTRFS_MAX_MIRRORS);
 		goto error;
 	}
 
-	real_stripes = bbio->num_stripes - bbio->num_tgtdevs;
+	real_stripes = bioc->num_stripes - bioc->num_tgtdevs;
 	for (nzones = 0; nzones < real_stripes; ++nzones) {
 		struct reada_zone *zone;
 
-		dev = bbio->stripes[nzones].dev;
+		dev = bioc->stripes[nzones].dev;
 
 		/* cannot read ahead on missing device. */
 		if (!dev->bdev)
 			continue;
 
-		zone = reada_find_zone(dev, logical, bbio);
+		zone = reada_find_zone(dev, logical, bioc);
 		if (!zone)
 			continue;
 
@@ -464,7 +464,7 @@
 	if (!have_zone)
 		goto error;
 
-	btrfs_put_bbio(bbio);
+	btrfs_put_bioc(bioc);
 	return re;
 
 error:
@@ -488,7 +488,7 @@
 		kref_put(&zone->refcnt, reada_zone_release);
 		spin_unlock(&fs_info->reada_lock);
 	}
-	btrfs_put_bbio(bbio);
+	btrfs_put_bioc(bioc);
 	kfree(re);
 	return re_exist;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/ref-verify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/ref-verify.c
@@ -788,6 +788,7 @@
 			dump_ref_action(fs_info, ra);
 			kfree(ref);
 			kfree(ra);
+			kfree(re);
 			goto out_unlock;
 		} else if (be->num_refs == 0) {
 			btrfs_err(fs_info,
@@ -797,6 +798,7 @@
 			dump_ref_action(fs_info, ra);
 			kfree(ref);
 			kfree(ra);
+			kfree(re);
 			goto out_unlock;
 		}
 
@@ -844,6 +846,7 @@
 "dropping a ref for a root that doesn't have a ref on the block");
 			dump_block_entry(fs_info, be);
 			dump_ref_action(fs_info, ra);
+			rb_erase(&ref->node, &be->refs);
 			kfree(ref);
 			kfree(ra);
 			goto out_unlock;
@@ -881,8 +884,10 @@
 out_unlock:
 	spin_unlock(&fs_info->ref_verify_lock);
 out:
-	if (ret)
+	if (ret) {
+		btrfs_free_ref_cache(fs_info);
 		btrfs_clear_opt(fs_info->mount_opt, REF_VERIFY);
+	}
 	return ret;
 }
 
@@ -1011,8 +1016,8 @@
 		}
 	}
 	if (ret) {
-		btrfs_clear_opt(fs_info->mount_opt, REF_VERIFY);
 		btrfs_free_ref_cache(fs_info);
+		btrfs_clear_opt(fs_info->mount_opt, REF_VERIFY);
 	}
 	btrfs_free_path(path);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/reflink.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/reflink.c
@@ -505,8 +505,11 @@
 			 */
 			ASSERT(key.offset == 0);
 			ASSERT(datal <= fs_info->sectorsize);
-			if (key.offset != 0 || datal > fs_info->sectorsize)
-				return -EUCLEAN;
+			if (WARN_ON(key.offset != 0) ||
+			    WARN_ON(datal > fs_info->sectorsize)) {
+				ret = -EUCLEAN;
+				goto out;
+			}
 
 			ret = clone_copy_inline_extent(inode, path, &new_key,
 						       drop_start, datal, size,
@@ -649,7 +652,7 @@
 static int btrfs_extent_same(struct inode *src, u64 loff, u64 olen,
 			     struct inode *dst, u64 dst_loff)
 {
-	int ret;
+	int ret = 0;
 	u64 i, tail_len, chunk_count;
 	struct btrfs_root *root_dst = BTRFS_I(dst)->root;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/relocation.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/relocation.c
@@ -919,7 +919,7 @@
 	btrfs_grab_root(reloc_root);
 
 	/* root->reloc_root will stay until current relocation finished */
-	if (fs_info->reloc_ctl->merge_reloc_tree &&
+	if (fs_info->reloc_ctl && fs_info->reloc_ctl->merge_reloc_tree &&
 	    btrfs_root_refs(root_item) == 0) {
 		set_bit(BTRFS_ROOT_DEAD_RELOC_TREE, &root->state);
 		/*
@@ -1147,7 +1147,8 @@
 				       num_bytes, parent);
 		ref.real_root = root->root_key.objectid;
 		btrfs_init_data_ref(&ref, btrfs_header_owner(leaf),
-				    key.objectid, key.offset);
+				    key.objectid, key.offset,
+				    root->root_key.objectid, false);
 		ret = btrfs_inc_extent_ref(trans, &ref);
 		if (ret) {
 			btrfs_abort_transaction(trans, ret);
@@ -1158,7 +1159,8 @@
 				       num_bytes, parent);
 		ref.real_root = root->root_key.objectid;
 		btrfs_init_data_ref(&ref, btrfs_header_owner(leaf),
-				    key.objectid, key.offset);
+				    key.objectid, key.offset,
+				    root->root_key.objectid, false);
 		ret = btrfs_free_extent(trans, &ref);
 		if (ret) {
 			btrfs_abort_transaction(trans, ret);
@@ -1324,7 +1326,9 @@
 		btrfs_release_path(path);
 
 		path->lowest_level = level;
+		set_bit(BTRFS_ROOT_RESET_LOCKDEP_CLASS, &src->state);
 		ret = btrfs_search_slot(trans, src, &key, path, 0, 1);
+		clear_bit(BTRFS_ROOT_RESET_LOCKDEP_CLASS, &src->state);
 		path->lowest_level = 0;
 		if (ret) {
 			if (ret > 0)
@@ -1368,7 +1372,8 @@
 		btrfs_init_generic_ref(&ref, BTRFS_ADD_DELAYED_REF, old_bytenr,
 				       blocksize, path->nodes[level]->start);
 		ref.skip_qgroup = true;
-		btrfs_init_tree_ref(&ref, level - 1, src->root_key.objectid);
+		btrfs_init_tree_ref(&ref, level - 1, src->root_key.objectid,
+				    0, true);
 		ret = btrfs_inc_extent_ref(trans, &ref);
 		if (ret) {
 			btrfs_abort_transaction(trans, ret);
@@ -1377,7 +1382,8 @@
 		btrfs_init_generic_ref(&ref, BTRFS_ADD_DELAYED_REF, new_bytenr,
 				       blocksize, 0);
 		ref.skip_qgroup = true;
-		btrfs_init_tree_ref(&ref, level - 1, dest->root_key.objectid);
+		btrfs_init_tree_ref(&ref, level - 1, dest->root_key.objectid, 0,
+				    true);
 		ret = btrfs_inc_extent_ref(trans, &ref);
 		if (ret) {
 			btrfs_abort_transaction(trans, ret);
@@ -1386,7 +1392,8 @@
 
 		btrfs_init_generic_ref(&ref, BTRFS_DROP_DELAYED_REF, new_bytenr,
 				       blocksize, path->nodes[level]->start);
-		btrfs_init_tree_ref(&ref, level - 1, src->root_key.objectid);
+		btrfs_init_tree_ref(&ref, level - 1, src->root_key.objectid,
+				    0, true);
 		ref.skip_qgroup = true;
 		ret = btrfs_free_extent(trans, &ref);
 		if (ret) {
@@ -1396,7 +1403,8 @@
 
 		btrfs_init_generic_ref(&ref, BTRFS_DROP_DELAYED_REF, old_bytenr,
 				       blocksize, 0);
-		btrfs_init_tree_ref(&ref, level - 1, dest->root_key.objectid);
+		btrfs_init_tree_ref(&ref, level - 1, dest->root_key.objectid,
+				    0, true);
 		ref.skip_qgroup = true;
 		ret = btrfs_free_extent(trans, &ref);
 		if (ret) {
@@ -1897,7 +1905,39 @@
 				err = PTR_ERR(root);
 			break;
 		}
-		ASSERT(root->reloc_root == reloc_root);
+
+		if (unlikely(root->reloc_root != reloc_root)) {
+			if (root->reloc_root) {
+				btrfs_err(fs_info,
+"reloc tree mismatch, root %lld has reloc root key (%lld %u %llu) gen %llu, expect reloc root key (%lld %u %llu) gen %llu",
+					  root->root_key.objectid,
+					  root->reloc_root->root_key.objectid,
+					  root->reloc_root->root_key.type,
+					  root->reloc_root->root_key.offset,
+					  btrfs_root_generation(
+						  &root->reloc_root->root_item),
+					  reloc_root->root_key.objectid,
+					  reloc_root->root_key.type,
+					  reloc_root->root_key.offset,
+					  btrfs_root_generation(
+						  &reloc_root->root_item));
+			} else {
+				btrfs_err(fs_info,
+"reloc tree mismatch, root %lld has no reloc root, expect reloc root key (%lld %u %llu) gen %llu",
+					  root->root_key.objectid,
+					  reloc_root->root_key.objectid,
+					  reloc_root->root_key.type,
+					  reloc_root->root_key.offset,
+					  btrfs_root_generation(
+						  &reloc_root->root_item));
+			}
+			list_add(&reloc_root->root_list, &reloc_roots);
+			btrfs_put_root(root);
+			btrfs_abort_transaction(trans, -EUCLEAN);
+			if (!err)
+				err = -EUCLEAN;
+			break;
+		}
 
 		/*
 		 * set reference count to 1, so btrfs_recover_relocation
@@ -1970,7 +2010,7 @@
 		root = btrfs_get_fs_root(fs_info, reloc_root->root_key.offset,
 					 false);
 		if (btrfs_root_refs(&reloc_root->root_item) > 0) {
-			if (IS_ERR(root)) {
+			if (WARN_ON(IS_ERR(root))) {
 				/*
 				 * For recovery we read the fs roots on mount,
 				 * and if we didn't find the root then we marked
@@ -1979,17 +2019,14 @@
 				 * memory.  However there's no reason we can't
 				 * handle the error properly here just in case.
 				 */
-				ASSERT(0);
 				ret = PTR_ERR(root);
 				goto out;
 			}
-			if (root->reloc_root != reloc_root) {
+			if (WARN_ON(root->reloc_root != reloc_root)) {
 				/*
-				 * This is actually impossible without something
-				 * going really wrong (like weird race condition
-				 * or cosmic rays).
+				 * This can happen if on-disk metadata has some
+				 * corruption, e.g. bad reloc tree key offset.
 				 */
-				ASSERT(0);
 				ret = -EINVAL;
 				goto out;
 			}
@@ -2475,7 +2512,8 @@
 					       upper->eb->start);
 			ref.real_root = root->root_key.objectid;
 			btrfs_init_tree_ref(&ref, node->level,
-					    btrfs_header_owner(upper->eb));
+					    btrfs_header_owner(upper->eb),
+					    root->root_key.objectid, false);
 			ret = btrfs_inc_extent_ref(trans, &ref);
 			if (!ret)
 				ret = btrfs_drop_subtree(trans, root, eb,
@@ -2691,8 +2729,12 @@
 			list_add_tail(&node->list, &rc->backref_cache.changed);
 		} else {
 			path->lowest_level = node->level;
+			if (root == root->fs_info->chunk_root)
+				btrfs_reserve_chunk_metadata(trans, false);
 			ret = btrfs_search_slot(trans, root, key, path, 0, 1);
 			btrfs_release_path(path);
+			if (root == root->fs_info->chunk_root)
+				btrfs_trans_release_chunk_metadata(trans);
 			if (ret > 0)
 				ret = 0;
 		}
@@ -2852,31 +2894,6 @@
 	if (ret)
 		return ret;
 
-	/*
-	 * On a zoned filesystem, we cannot preallocate the file region.
-	 * Instead, we dirty and fiemap_write the region.
-	 */
-	if (btrfs_is_zoned(inode->root->fs_info)) {
-		struct btrfs_root *root = inode->root;
-		struct btrfs_trans_handle *trans;
-
-		end = cluster->end - offset + 1;
-		trans = btrfs_start_transaction(root, 1);
-		if (IS_ERR(trans))
-			return PTR_ERR(trans);
-
-		inode->vfs_inode.i_ctime = current_time(&inode->vfs_inode);
-		i_size_write(&inode->vfs_inode, end);
-		ret = btrfs_update_inode(trans, root, inode);
-		if (ret) {
-			btrfs_abort_transaction(trans, ret);
-			btrfs_end_transaction(trans);
-			return ret;
-		}
-
-		return btrfs_end_transaction(trans);
-	}
-
 	btrfs_inode_lock(&inode->vfs_inode, 0);
 	for (nr = 0; nr < cluster->nr; nr++) {
 		start = cluster->boundary[nr] - offset;
@@ -3084,7 +3101,6 @@
 static int relocate_file_extent_cluster(struct inode *inode,
 					struct file_extent_cluster *cluster)
 {
-	struct btrfs_fs_info *fs_info = btrfs_sb(inode->i_sb);
 	u64 offset = BTRFS_I(inode)->index_cnt;
 	unsigned long index;
 	unsigned long last_index;
@@ -3114,8 +3130,6 @@
 	for (index = (cluster->start - offset) >> PAGE_SHIFT;
 	     index <= last_index && !ret; index++)
 		ret = relocate_one_page(inode, ra, cluster, &cluster_nr, index);
-	if (btrfs_is_zoned(fs_info) && !ret)
-		ret = btrfs_wait_ordered_range(inode, 0, (u64)-1);
 	if (ret == 0)
 		WARN_ON(cluster_nr != cluster->nr);
 out:
@@ -3593,7 +3607,12 @@
 		 */
 		return PTR_ERR(trans);
 	}
-	return btrfs_commit_transaction(trans);
+
+	ret = btrfs_commit_transaction(trans);
+	if (ret)
+		unset_reloc_control(rc);
+
+	return ret;
 }
 
 static noinline_for_stack int relocate_block_group(struct reloc_control *rc)
@@ -3770,12 +3789,8 @@
 	struct btrfs_path *path;
 	struct btrfs_inode_item *item;
 	struct extent_buffer *leaf;
-	u64 flags = BTRFS_INODE_NOCOMPRESS | BTRFS_INODE_PREALLOC;
 	int ret;
 
-	if (btrfs_is_zoned(trans->fs_info))
-		flags &= ~BTRFS_INODE_PREALLOC;
-
 	path = btrfs_alloc_path();
 	if (!path)
 		return -ENOMEM;
@@ -3790,7 +3805,8 @@
 	btrfs_set_inode_generation(leaf, item, 1);
 	btrfs_set_inode_size(leaf, item, 0);
 	btrfs_set_inode_mode(leaf, item, S_IFREG | 0600);
-	btrfs_set_inode_flags(leaf, item, flags);
+	btrfs_set_inode_flags(leaf, item, BTRFS_INODE_NOCOMPRESS |
+					  BTRFS_INODE_PREALLOC);
 	btrfs_mark_buffer_dirty(leaf);
 out:
 	btrfs_free_path(path);
@@ -3885,25 +3901,14 @@
  *   0             success
  *   -EINPROGRESS  operation is already in progress, that's probably a bug
  *   -ECANCELED    cancellation request was set before the operation started
- *   -EAGAIN       can not start because there are ongoing send operations
  */
 static int reloc_chunk_start(struct btrfs_fs_info *fs_info)
 {
-	spin_lock(&fs_info->send_reloc_lock);
-	if (fs_info->send_in_progress) {
-		btrfs_warn_rl(fs_info,
-"cannot run relocation while send operations are in progress (%d in progress)",
-			      fs_info->send_in_progress);
-		spin_unlock(&fs_info->send_reloc_lock);
-		return -EAGAIN;
-	}
 	if (test_and_set_bit(BTRFS_FS_RELOC_RUNNING, &fs_info->flags)) {
 		/* This should not happen */
-		spin_unlock(&fs_info->send_reloc_lock);
 		btrfs_err(fs_info, "reloc already running, cannot start");
 		return -EINPROGRESS;
 	}
-	spin_unlock(&fs_info->send_reloc_lock);
 
 	if (atomic_read(&fs_info->reloc_cancel_req) > 0) {
 		btrfs_info(fs_info, "chunk relocation canceled on start");
@@ -3925,9 +3930,7 @@
 	/* Requested after start, clear bit first so any waiters can continue */
 	if (atomic_read(&fs_info->reloc_cancel_req) > 0)
 		btrfs_info(fs_info, "chunk relocation canceled during operation");
-	spin_lock(&fs_info->send_reloc_lock);
 	clear_and_wake_up_bit(BTRFS_FS_RELOC_RUNNING, &fs_info->flags);
-	spin_unlock(&fs_info->send_reloc_lock);
 	atomic_set(&fs_info->reloc_cancel_req, 0);
 }
 
@@ -3998,6 +4001,19 @@
 	int rw = 0;
 	int err = 0;
 
+	/*
+	 * This only gets set if we had a half-deleted snapshot on mount.  We
+	 * cannot allow relocation to start while we're still trying to clean up
+	 * these pending deletions.
+	 */
+	ret = wait_on_bit(&fs_info->flags, BTRFS_FS_UNFINISHED_DROPS, TASK_INTERRUPTIBLE);
+	if (ret)
+		return ret;
+
+	/* We may have been woken up by close_ctree, so bail if we're closing. */
+	if (btrfs_fs_closing(fs_info))
+		return -EINTR;
+
 	bg = btrfs_lookup_block_group(fs_info, group_start);
 	if (!bg)
 		return -ENOENT;
@@ -4386,8 +4402,7 @@
 	if (!rc)
 		return 0;
 
-	BUG_ON(rc->stage == UPDATE_DATA_PTRS &&
-	       root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID);
+	BUG_ON(rc->stage == UPDATE_DATA_PTRS && btrfs_is_data_reloc_root(root));
 
 	level = btrfs_header_level(buf);
 	if (btrfs_header_generation(buf) <=
@@ -4399,8 +4414,18 @@
 		WARN_ON(!first_cow && level == 0);
 
 		node = rc->backref_cache.path[level];
-		BUG_ON(node->bytenr != buf->start &&
-		       node->new_bytenr != buf->start);
+
+		/*
+		 * If node->bytenr != buf->start and node->new_bytenr !=
+		 * buf->start then we've got the wrong backref node for what we
+		 * expected to see here and the cache is incorrect.
+		 */
+		if (unlikely(node->bytenr != buf->start && node->new_bytenr != buf->start)) {
+			btrfs_err(fs_info,
+"bytenr %llu was found but our backref cache was expecting %llu or %llu",
+				  buf->start, node->bytenr, node->new_bytenr);
+			return -EUCLEAN;
+		}
 
 		btrfs_backref_drop_node_buffer(node);
 		atomic_inc(&cow->refs);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/root-tree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/root-tree.c
@@ -280,6 +280,21 @@
 
 		WARN_ON(!test_bit(BTRFS_ROOT_ORPHAN_ITEM_INSERTED, &root->state));
 		if (btrfs_root_refs(&root->root_item) == 0) {
+			struct btrfs_key drop_key;
+
+			btrfs_disk_key_to_cpu(&drop_key, &root->root_item.drop_progress);
+			/*
+			 * If we have a non-zero drop_progress then we know we
+			 * made it partly through deleting this snapshot, and
+			 * thus we need to make sure we block any balance from
+			 * happening until this snapshot is completely dropped.
+			 */
+			if (drop_key.objectid != 0 || drop_key.type != 0 ||
+			    drop_key.offset != 0) {
+				set_bit(BTRFS_FS_UNFINISHED_DROPS, &fs_info->flags);
+				set_bit(BTRFS_ROOT_UNFINISHED_DROP, &root->state);
+			}
+
 			set_bit(BTRFS_ROOT_DEAD_TREE, &root->state);
 			btrfs_add_dead_root(root);
 		}
@@ -336,8 +351,10 @@
 	key.offset = ref_id;
 again:
 	ret = btrfs_search_slot(trans, tree_root, &key, path, -1, 1);
-	BUG_ON(ret < 0);
-	if (ret == 0) {
+	if (ret < 0) {
+		err = ret;
+		goto out;
+	} else if (ret == 0) {
 		leaf = path->nodes[0];
 		ref = btrfs_item_ptr(leaf, path->slots[0],
 				     struct btrfs_root_ref);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/scrub.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/scrub.c
@@ -57,7 +57,7 @@
 
 struct scrub_recover {
 	refcount_t		refs;
-	struct btrfs_bio	*bbio;
+	struct btrfs_io_context	*bioc;
 	u64			map_length;
 };
 
@@ -73,8 +73,8 @@
 	u64			physical_for_dev_replace;
 	atomic_t		refs;
 	u8			mirror_num;
-	int			have_csum:1;
-	int			io_error:1;
+	unsigned int		have_csum:1;
+	unsigned int		io_error:1;
 	u8			csum[BTRFS_CSUM_SIZE];
 
 	struct scrub_recover	*recover;
@@ -254,7 +254,7 @@
 static inline int scrub_is_page_on_raid56(struct scrub_page *spage)
 {
 	return spage->recover &&
-	       (spage->recover->bbio->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK);
+	       (spage->recover->bioc->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK);
 }
 
 static void scrub_pending_bio_inc(struct scrub_ctx *sctx)
@@ -798,7 +798,7 @@
 {
 	if (refcount_dec_and_test(&recover->refs)) {
 		btrfs_bio_counter_dec(fs_info);
-		btrfs_put_bbio(recover->bbio);
+		btrfs_put_bioc(recover->bioc);
 		kfree(recover);
 	}
 }
@@ -1027,8 +1027,7 @@
 			sblock_other = sblocks_for_recheck + mirror_index;
 		} else {
 			struct scrub_recover *r = sblock_bad->pagev[0]->recover;
-			int max_allowed = r->bbio->num_stripes -
-						r->bbio->num_tgtdevs;
+			int max_allowed = r->bioc->num_stripes - r->bioc->num_tgtdevs;
 
 			if (mirror_index >= max_allowed)
 				break;
@@ -1218,14 +1217,14 @@
 	return 0;
 }
 
-static inline int scrub_nr_raid_mirrors(struct btrfs_bio *bbio)
+static inline int scrub_nr_raid_mirrors(struct btrfs_io_context *bioc)
 {
-	if (bbio->map_type & BTRFS_BLOCK_GROUP_RAID5)
+	if (bioc->map_type & BTRFS_BLOCK_GROUP_RAID5)
 		return 2;
-	else if (bbio->map_type & BTRFS_BLOCK_GROUP_RAID6)
+	else if (bioc->map_type & BTRFS_BLOCK_GROUP_RAID6)
 		return 3;
 	else
-		return (int)bbio->num_stripes;
+		return (int)bioc->num_stripes;
 }
 
 static inline void scrub_stripe_index_and_offset(u64 logical, u64 map_type,
@@ -1269,7 +1268,7 @@
 	u64 flags = original_sblock->pagev[0]->flags;
 	u64 have_csum = original_sblock->pagev[0]->have_csum;
 	struct scrub_recover *recover;
-	struct btrfs_bio *bbio;
+	struct btrfs_io_context *bioc;
 	u64 sublen;
 	u64 mapped_length;
 	u64 stripe_offset;
@@ -1288,7 +1287,7 @@
 	while (length > 0) {
 		sublen = min_t(u64, length, fs_info->sectorsize);
 		mapped_length = sublen;
-		bbio = NULL;
+		bioc = NULL;
 
 		/*
 		 * With a length of sectorsize, each returned stripe represents
@@ -1296,27 +1295,27 @@
 		 */
 		btrfs_bio_counter_inc_blocked(fs_info);
 		ret = btrfs_map_sblock(fs_info, BTRFS_MAP_GET_READ_MIRRORS,
-				logical, &mapped_length, &bbio);
-		if (ret || !bbio || mapped_length < sublen) {
-			btrfs_put_bbio(bbio);
+				       logical, &mapped_length, &bioc);
+		if (ret || !bioc || mapped_length < sublen) {
+			btrfs_put_bioc(bioc);
 			btrfs_bio_counter_dec(fs_info);
 			return -EIO;
 		}
 
 		recover = kzalloc(sizeof(struct scrub_recover), GFP_NOFS);
 		if (!recover) {
-			btrfs_put_bbio(bbio);
+			btrfs_put_bioc(bioc);
 			btrfs_bio_counter_dec(fs_info);
 			return -ENOMEM;
 		}
 
 		refcount_set(&recover->refs, 1);
-		recover->bbio = bbio;
+		recover->bioc = bioc;
 		recover->map_length = mapped_length;
 
 		BUG_ON(page_index >= SCRUB_MAX_PAGES_PER_BLOCK);
 
-		nmirrors = min(scrub_nr_raid_mirrors(bbio), BTRFS_MAX_MIRRORS);
+		nmirrors = min(scrub_nr_raid_mirrors(bioc), BTRFS_MAX_MIRRORS);
 
 		for (mirror_index = 0; mirror_index < nmirrors;
 		     mirror_index++) {
@@ -1348,17 +1347,17 @@
 				       sctx->fs_info->csum_size);
 
 			scrub_stripe_index_and_offset(logical,
-						      bbio->map_type,
-						      bbio->raid_map,
+						      bioc->map_type,
+						      bioc->raid_map,
 						      mapped_length,
-						      bbio->num_stripes -
-						      bbio->num_tgtdevs,
+						      bioc->num_stripes -
+						      bioc->num_tgtdevs,
 						      mirror_index,
 						      &stripe_index,
 						      &stripe_offset);
-			spage->physical = bbio->stripes[stripe_index].physical +
+			spage->physical = bioc->stripes[stripe_index].physical +
 					 stripe_offset;
-			spage->dev = bbio->stripes[stripe_index].dev;
+			spage->dev = bioc->stripes[stripe_index].dev;
 
 			BUG_ON(page_index >= original_sblock->page_count);
 			spage->physical_for_dev_replace =
@@ -1401,7 +1400,7 @@
 	bio->bi_end_io = scrub_bio_wait_endio;
 
 	mirror_num = spage->sblock->pagev[0]->mirror_num;
-	ret = raid56_parity_recover(fs_info, bio, spage->recover->bbio,
+	ret = raid56_parity_recover(fs_info, bio, spage->recover->bioc,
 				    spage->recover->map_length,
 				    mirror_num, 0);
 	if (ret)
@@ -2203,7 +2202,7 @@
 	struct btrfs_fs_info *fs_info = sctx->fs_info;
 	u64 length = sblock->page_count * PAGE_SIZE;
 	u64 logical = sblock->pagev[0]->logical;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	struct bio *bio;
 	struct btrfs_raid_bio *rbio;
 	int ret;
@@ -2211,19 +2210,19 @@
 
 	btrfs_bio_counter_inc_blocked(fs_info);
 	ret = btrfs_map_sblock(fs_info, BTRFS_MAP_GET_READ_MIRRORS, logical,
-			&length, &bbio);
-	if (ret || !bbio || !bbio->raid_map)
-		goto bbio_out;
+			       &length, &bioc);
+	if (ret || !bioc || !bioc->raid_map)
+		goto bioc_out;
 
 	if (WARN_ON(!sctx->is_dev_replace ||
-		    !(bbio->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK))) {
+		    !(bioc->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK))) {
 		/*
 		 * We shouldn't be scrubbing a missing device. Even for dev
 		 * replace, we should only get here for RAID 5/6. We either
 		 * managed to mount something with no mirrors remaining or
 		 * there's a bug in scrub_remap_extent()/btrfs_map_block().
 		 */
-		goto bbio_out;
+		goto bioc_out;
 	}
 
 	bio = btrfs_io_bio_alloc(0);
@@ -2231,7 +2230,7 @@
 	bio->bi_private = sblock;
 	bio->bi_end_io = scrub_missing_raid56_end_io;
 
-	rbio = raid56_alloc_missing_rbio(fs_info, bio, bbio, length);
+	rbio = raid56_alloc_missing_rbio(fs_info, bio, bioc, length);
 	if (!rbio)
 		goto rbio_out;
 
@@ -2249,9 +2248,9 @@
 
 rbio_out:
 	bio_put(bio);
-bbio_out:
+bioc_out:
 	btrfs_bio_counter_dec(fs_info);
-	btrfs_put_bbio(bbio);
+	btrfs_put_bioc(bioc);
 	spin_lock(&sctx->stat_lock);
 	sctx->stat.malloc_errors++;
 	spin_unlock(&sctx->stat_lock);
@@ -2826,7 +2825,7 @@
 	struct btrfs_fs_info *fs_info = sctx->fs_info;
 	struct bio *bio;
 	struct btrfs_raid_bio *rbio;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	u64 length;
 	int ret;
 
@@ -2838,16 +2837,16 @@
 
 	btrfs_bio_counter_inc_blocked(fs_info);
 	ret = btrfs_map_sblock(fs_info, BTRFS_MAP_WRITE, sparity->logic_start,
-			       &length, &bbio);
-	if (ret || !bbio || !bbio->raid_map)
-		goto bbio_out;
+			       &length, &bioc);
+	if (ret || !bioc || !bioc->raid_map)
+		goto bioc_out;
 
 	bio = btrfs_io_bio_alloc(0);
 	bio->bi_iter.bi_sector = sparity->logic_start >> 9;
 	bio->bi_private = sparity;
 	bio->bi_end_io = scrub_parity_bio_endio;
 
-	rbio = raid56_parity_alloc_scrub_rbio(fs_info, bio, bbio,
+	rbio = raid56_parity_alloc_scrub_rbio(fs_info, bio, bioc,
 					      length, sparity->scrub_dev,
 					      sparity->dbitmap,
 					      sparity->nsectors);
@@ -2860,9 +2859,9 @@
 
 rbio_out:
 	bio_put(bio);
-bbio_out:
+bioc_out:
 	btrfs_bio_counter_dec(fs_info);
-	btrfs_put_bbio(bbio);
+	btrfs_put_bioc(bioc);
 	bitmap_or(sparity->ebitmap, sparity->ebitmap, sparity->dbitmap,
 		  sparity->nsectors);
 	spin_lock(&sctx->stat_lock);
@@ -2901,7 +2900,7 @@
 	struct btrfs_root *root = fs_info->extent_root;
 	struct btrfs_root *csum_root = fs_info->csum_root;
 	struct btrfs_extent_item *extent;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	u64 flags;
 	int ret;
 	int slot;
@@ -3044,22 +3043,22 @@
 						       extent_len);
 
 			mapped_length = extent_len;
-			bbio = NULL;
+			bioc = NULL;
 			ret = btrfs_map_block(fs_info, BTRFS_MAP_READ,
-					extent_logical, &mapped_length, &bbio,
+					extent_logical, &mapped_length, &bioc,
 					0);
 			if (!ret) {
-				if (!bbio || mapped_length < extent_len)
+				if (!bioc || mapped_length < extent_len)
 					ret = -EIO;
 			}
 			if (ret) {
-				btrfs_put_bbio(bbio);
+				btrfs_put_bioc(bioc);
 				goto out;
 			}
-			extent_physical = bbio->stripes[0].physical;
-			extent_mirror_num = bbio->mirror_num;
-			extent_dev = bbio->stripes[0].dev;
-			btrfs_put_bbio(bbio);
+			extent_physical = bioc->stripes[0].physical;
+			extent_mirror_num = bioc->mirror_num;
+			extent_dev = bioc->stripes[0].dev;
+			btrfs_put_bioc(bioc);
 
 			ret = btrfs_lookup_csums_range(csum_root,
 						extent_logical,
@@ -3813,13 +3812,20 @@
 
 		if (ret == 0) {
 			ro_set = 1;
-		} else if (ret == -ENOSPC && !sctx->is_dev_replace) {
+		} else if (ret == -ENOSPC && !sctx->is_dev_replace &&
+			   !(cache->flags & BTRFS_BLOCK_GROUP_RAID56_MASK)) {
 			/*
 			 * btrfs_inc_block_group_ro return -ENOSPC when it
 			 * failed in creating new chunk for metadata.
 			 * It is not a problem for scrub, because
 			 * metadata are always cowed, and our scrub paused
 			 * commit_transactions.
+			 *
+			 * For RAID56 chunks, we have to mark them read-only
+			 * for scrub, as later we would use our own cache
+			 * out of RAID56 realm.
+			 * Thus we want the RAID56 bg to be marked RO to
+			 * prevent RMW from screwing up out cache.
 			 */
 			ro_set = 0;
 		} else if (ret == -ETXTBSY) {
@@ -3966,7 +3972,17 @@
 		gen = fs_info->last_trans_committed;
 
 	for (i = 0; i < BTRFS_SUPER_MIRROR_MAX; i++) {
-		bytenr = btrfs_sb_offset(i);
+		ret = btrfs_sb_log_location(scrub_dev, i, 0, &bytenr);
+		if (ret == -ENOENT)
+			break;
+
+		if (ret) {
+			spin_lock(&sctx->stat_lock);
+			sctx->stat.super_errors++;
+			spin_unlock(&sctx->stat_lock);
+			continue;
+		}
+
 		if (bytenr + BTRFS_SUPER_INFO_SIZE >
 		    scrub_dev->commit_total_bytes)
 			break;
@@ -4068,10 +4084,12 @@
 		    u64 end, struct btrfs_scrub_progress *progress,
 		    int readonly, int is_dev_replace)
 {
+	struct btrfs_dev_lookup_args args = { .devid = devid };
 	struct scrub_ctx *sctx;
 	int ret;
 	struct btrfs_device *dev;
 	unsigned int nofs_flag;
+	bool need_commit = false;
 
 	if (btrfs_fs_closing(fs_info))
 		return -EAGAIN;
@@ -4115,7 +4133,7 @@
 		goto out_free_ctx;
 
 	mutex_lock(&fs_info->fs_devices->device_list_mutex);
-	dev = btrfs_find_device(fs_info->fs_devices, devid, NULL, NULL);
+	dev = btrfs_find_device(fs_info->fs_devices, &args);
 	if (!dev || (test_bit(BTRFS_DEV_STATE_MISSING, &dev->dev_state) &&
 		     !is_dev_replace)) {
 		mutex_unlock(&fs_info->fs_devices->device_list_mutex);
@@ -4177,6 +4195,12 @@
 	 */
 	nofs_flag = memalloc_nofs_save();
 	if (!is_dev_replace) {
+		u64 old_super_errors;
+
+		spin_lock(&sctx->stat_lock);
+		old_super_errors = sctx->stat.super_errors;
+		spin_unlock(&sctx->stat_lock);
+
 		btrfs_info(fs_info, "scrub: started on devid %llu", devid);
 		/*
 		 * by holding device list mutex, we can
@@ -4185,6 +4209,16 @@
 		mutex_lock(&fs_info->fs_devices->device_list_mutex);
 		ret = scrub_supers(sctx, dev);
 		mutex_unlock(&fs_info->fs_devices->device_list_mutex);
+
+		spin_lock(&sctx->stat_lock);
+		/*
+		 * Super block errors found, but we can not commit transaction
+		 * at current context, since btrfs_commit_transaction() needs
+		 * to pause the current running scrub (hold by ourselves).
+		 */
+		if (sctx->stat.super_errors > old_super_errors && !sctx->readonly)
+			need_commit = true;
+		spin_unlock(&sctx->stat_lock);
 	}
 
 	if (!ret)
@@ -4211,6 +4245,25 @@
 	scrub_workers_put(fs_info);
 	scrub_put_ctx(sctx);
 
+	/*
+	 * We found some super block errors before, now try to force a
+	 * transaction commit, as scrub has finished.
+	 */
+	if (need_commit) {
+		struct btrfs_trans_handle *trans;
+
+		trans = btrfs_start_transaction(fs_info->tree_root, 0);
+		if (IS_ERR(trans)) {
+			ret = PTR_ERR(trans);
+			btrfs_err(fs_info,
+	"scrub: failed to start transaction to fix super block errors: %d", ret);
+			return ret;
+		}
+		ret = btrfs_commit_transaction(trans);
+		if (ret < 0)
+			btrfs_err(fs_info,
+	"scrub: failed to commit transaction to fix super block errors: %d", ret);
+	}
 	return ret;
 out:
 	scrub_workers_put(fs_info);
@@ -4288,11 +4341,12 @@
 int btrfs_scrub_progress(struct btrfs_fs_info *fs_info, u64 devid,
 			 struct btrfs_scrub_progress *progress)
 {
+	struct btrfs_dev_lookup_args args = { .devid = devid };
 	struct btrfs_device *dev;
 	struct scrub_ctx *sctx = NULL;
 
 	mutex_lock(&fs_info->fs_devices->device_list_mutex);
-	dev = btrfs_find_device(fs_info->fs_devices, devid, NULL, NULL);
+	dev = btrfs_find_device(fs_info->fs_devices, &args);
 	if (dev)
 		sctx = dev->scrub_ctx;
 	if (sctx)
@@ -4309,20 +4363,20 @@
 			       int *extent_mirror_num)
 {
 	u64 mapped_length;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	int ret;
 
 	mapped_length = extent_len;
 	ret = btrfs_map_block(fs_info, BTRFS_MAP_READ, extent_logical,
-			      &mapped_length, &bbio, 0);
-	if (ret || !bbio || mapped_length < extent_len ||
-	    !bbio->stripes[0].dev->bdev) {
-		btrfs_put_bbio(bbio);
+			      &mapped_length, &bioc, 0);
+	if (ret || !bioc || mapped_length < extent_len ||
+	    !bioc->stripes[0].dev->bdev) {
+		btrfs_put_bioc(bioc);
 		return;
 	}
 
-	*extent_physical = bbio->stripes[0].physical;
-	*extent_mirror_num = bbio->mirror_num;
-	*extent_dev = bbio->stripes[0].dev;
-	btrfs_put_bbio(bbio);
+	*extent_physical = bioc->stripes[0].physical;
+	*extent_mirror_num = bioc->mirror_num;
+	*extent_dev = bioc->stripes[0].dev;
+	btrfs_put_bioc(bioc);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/send.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/send.c
@@ -24,6 +24,7 @@
 #include "transaction.h"
 #include "compression.h"
 #include "xattr.h"
+#include "print-tree.h"
 
 /*
  * Maximum number of references an extent can have in order for us to attempt to
@@ -96,6 +97,15 @@
 	struct btrfs_key *cmp_key;
 
 	/*
+	 * Keep track of the generation of the last transaction that was used
+	 * for relocating a block group. This is periodically checked in order
+	 * to detect if a relocation happened since the last check, so that we
+	 * don't operate on stale extent buffers for nodes (level >= 1) or on
+	 * stale disk_bytenr values of file extent items.
+	 */
+	u64 last_reloc_trans;
+
+	/*
 	 * infos of the currently processed inode. In case of deleted inodes,
 	 * these are the values from the deleted inode.
 	 */
@@ -685,7 +695,12 @@
 	if (WARN_ON(!sctx->send_buf))
 		return -EINVAL;
 
-	BUG_ON(sctx->send_size);
+	if (unlikely(sctx->send_size != 0)) {
+		btrfs_err(sctx->send_root->fs_info,
+			  "send: command header buffer not empty cmd %d offset %llu",
+			  cmd, sctx->send_off);
+		return -EINVAL;
+	}
 
 	sctx->send_size += sizeof(*hdr);
 	hdr = (struct btrfs_cmd_header *)sctx->send_buf;
@@ -966,7 +981,15 @@
 					ret = PTR_ERR(start);
 					goto out;
 				}
-				BUG_ON(start < p->buf);
+				if (unlikely(start < p->buf)) {
+					btrfs_err(root->fs_info,
+			"send: path ref buffer underflow for key (%llu %u %llu)",
+						  found_key->objectid,
+						  found_key->type,
+						  found_key->offset);
+					ret = -EINVAL;
+					goto out;
+				}
 			}
 			p->start = start;
 		} else {
@@ -1415,6 +1438,26 @@
 	if (ret < 0)
 		goto out;
 
+	down_read(&fs_info->commit_root_sem);
+	if (fs_info->last_reloc_trans > sctx->last_reloc_trans) {
+		/*
+		 * A transaction commit for a transaction in which block group
+		 * relocation was done just happened.
+		 * The disk_bytenr of the file extent item we processed is
+		 * possibly stale, referring to the extent's location before
+		 * relocation. So act as if we haven't found any clone sources
+		 * and fallback to write commands, which will read the correct
+		 * data from the new extent location. Otherwise we will fail
+		 * below because we haven't found our own back reference or we
+		 * could be getting incorrect sources in case the old extent
+		 * was already reallocated after the relocation.
+		 */
+		up_read(&fs_info->commit_root_sem);
+		ret = -ENOENT;
+		goto out;
+	}
+	up_read(&fs_info->commit_root_sem);
+
 	if (!backref_ctx.found_itself) {
 		/* found a bug in backref code? */
 		ret = -EIO;
@@ -4978,6 +5021,10 @@
 			lock_page(page);
 			if (!PageUptodate(page)) {
 				unlock_page(page);
+				btrfs_err(fs_info,
+			"send: IO error at offset %llu for inode %llu root %llu",
+					page_offset(page), sctx->cur_ino,
+					sctx->send_root->root_key.objectid);
 				put_page(page);
 				ret = -EIO;
 				break;
@@ -5364,6 +5411,7 @@
 		u64 ext_len;
 		u64 clone_len;
 		u64 clone_data_offset;
+		bool crossed_src_i_size = false;
 
 		if (slot >= btrfs_header_nritems(leaf)) {
 			ret = btrfs_next_leaf(clone_root->root, path);
@@ -5420,8 +5468,10 @@
 		if (key.offset >= clone_src_i_size)
 			break;
 
-		if (key.offset + ext_len > clone_src_i_size)
+		if (key.offset + ext_len > clone_src_i_size) {
 			ext_len = clone_src_i_size - key.offset;
+			crossed_src_i_size = true;
+		}
 
 		clone_data_offset = btrfs_file_extent_offset(leaf, ei);
 		if (btrfs_file_extent_disk_bytenr(leaf, ei) == disk_byte) {
@@ -5481,6 +5531,25 @@
 				ret = send_clone(sctx, offset, clone_len,
 						 clone_root);
 			}
+		} else if (crossed_src_i_size && clone_len < len) {
+			/*
+			 * If we are at i_size of the clone source inode and we
+			 * can not clone from it, terminate the loop. This is
+			 * to avoid sending two write operations, one with a
+			 * length matching clone_len and the final one after
+			 * this loop with a length of len - clone_len.
+			 *
+			 * When using encoded writes (BTRFS_SEND_FLAG_COMPRESSED
+			 * was passed to the send ioctl), this helps avoid
+			 * sending an encoded write for an offset that is not
+			 * sector size aligned, in case the i_size of the source
+			 * inode is not sector size aligned. That will make the
+			 * receiver fallback to decompression of the data and
+			 * writing it using regular buffered IO, therefore while
+			 * not incorrect, it's not optimal due decompression and
+			 * possible re-compression at the receiver.
+			 */
+			break;
 		} else {
 			ret = send_extent_data(sctx, offset, clone_len);
 		}
@@ -6592,6 +6661,50 @@
 {
 	int ret = 0;
 
+	/*
+	 * We can not hold the commit root semaphore here. This is because in
+	 * the case of sending and receiving to the same filesystem, using a
+	 * pipe, could result in a deadlock:
+	 *
+	 * 1) The task running send blocks on the pipe because it's full;
+	 *
+	 * 2) The task running receive, which is the only consumer of the pipe,
+	 *    is waiting for a transaction commit (for example due to a space
+	 *    reservation when doing a write or triggering a transaction commit
+	 *    when creating a subvolume);
+	 *
+	 * 3) The transaction is waiting to write lock the commit root semaphore,
+	 *    but can not acquire it since it's being held at 1).
+	 *
+	 * Down this call chain we write to the pipe through kernel_write().
+	 * The same type of problem can also happen when sending to a file that
+	 * is stored in the same filesystem - when reserving space for a write
+	 * into the file, we can trigger a transaction commit.
+	 *
+	 * Our caller has supplied us with clones of leaves from the send and
+	 * parent roots, so we're safe here from a concurrent relocation and
+	 * further reallocation of metadata extents while we are here. Below we
+	 * also assert that the leaves are clones.
+	 */
+	lockdep_assert_not_held(&sctx->send_root->fs_info->commit_root_sem);
+
+	/*
+	 * We always have a send root, so left_path is never NULL. We will not
+	 * have a leaf when we have reached the end of the send root but have
+	 * not yet reached the end of the parent root.
+	 */
+	if (left_path->nodes[0])
+		ASSERT(test_bit(EXTENT_BUFFER_UNMAPPED,
+				&left_path->nodes[0]->bflags));
+	/*
+	 * When doing a full send we don't have a parent root, so right_path is
+	 * NULL. When doing an incremental send, we may have reached the end of
+	 * the parent root already, so we don't have a leaf at right_path.
+	 */
+	if (right_path && right_path->nodes[0])
+		ASSERT(test_bit(EXTENT_BUFFER_UNMAPPED,
+				&right_path->nodes[0]->bflags));
+
 	if (result == BTRFS_COMPARE_TREE_SAME) {
 		if (key->type == BTRFS_INODE_REF_KEY ||
 		    key->type == BTRFS_INODE_EXTREF_KEY) {
@@ -6638,14 +6751,46 @@
 	return ret;
 }
 
+static int search_key_again(const struct send_ctx *sctx,
+			    struct btrfs_root *root,
+			    struct btrfs_path *path,
+			    const struct btrfs_key *key)
+{
+	int ret;
+
+	if (!path->need_commit_sem)
+		lockdep_assert_held_read(&root->fs_info->commit_root_sem);
+
+	/*
+	 * Roots used for send operations are readonly and no one can add,
+	 * update or remove keys from them, so we should be able to find our
+	 * key again. The only exception is deduplication, which can operate on
+	 * readonly roots and add, update or remove keys to/from them - but at
+	 * the moment we don't allow it to run in parallel with send.
+	 */
+	ret = btrfs_search_slot(NULL, root, key, path, 0, 0);
+	ASSERT(ret <= 0);
+	if (ret > 0) {
+		btrfs_print_tree(path->nodes[path->lowest_level], false);
+		btrfs_err(root->fs_info,
+"send: key (%llu %u %llu) not found in %s root %llu, lowest_level %d, slot %d",
+			  key->objectid, key->type, key->offset,
+			  (root == sctx->parent_root ? "parent" : "send"),
+			  root->root_key.objectid, path->lowest_level,
+			  path->slots[path->lowest_level]);
+		return -EUCLEAN;
+	}
+
+	return ret;
+}
+
 static int full_send_tree(struct send_ctx *sctx)
 {
 	int ret;
 	struct btrfs_root *send_root = sctx->send_root;
 	struct btrfs_key key;
+	struct btrfs_fs_info *fs_info = send_root->fs_info;
 	struct btrfs_path *path;
-	struct extent_buffer *eb;
-	int slot;
 
 	path = alloc_path_for_send();
 	if (!path)
@@ -6656,6 +6801,10 @@
 	key.type = BTRFS_INODE_ITEM_KEY;
 	key.offset = 0;
 
+	down_read(&fs_info->commit_root_sem);
+	sctx->last_reloc_trans = fs_info->last_reloc_trans;
+	up_read(&fs_info->commit_root_sem);
+
 	ret = btrfs_search_slot_for_read(send_root, &key, path, 1, 0);
 	if (ret < 0)
 		goto out;
@@ -6663,15 +6812,35 @@
 		goto out_finish;
 
 	while (1) {
-		eb = path->nodes[0];
-		slot = path->slots[0];
-		btrfs_item_key_to_cpu(eb, &key, slot);
+		btrfs_item_key_to_cpu(path->nodes[0], &key, path->slots[0]);
 
 		ret = changed_cb(path, NULL, &key,
 				 BTRFS_COMPARE_TREE_NEW, sctx);
 		if (ret < 0)
 			goto out;
 
+		down_read(&fs_info->commit_root_sem);
+		if (fs_info->last_reloc_trans > sctx->last_reloc_trans) {
+			sctx->last_reloc_trans = fs_info->last_reloc_trans;
+			up_read(&fs_info->commit_root_sem);
+			/*
+			 * A transaction used for relocating a block group was
+			 * committed or is about to finish its commit. Release
+			 * our path (leaf) and restart the search, so that we
+			 * avoid operating on any file extent items that are
+			 * stale, with a disk_bytenr that reflects a pre
+			 * relocation value. This way we avoid as much as
+			 * possible to fallback to regular writes when checking
+			 * if we can clone file ranges.
+			 */
+			btrfs_release_path(path);
+			ret = search_key_again(sctx, send_root, path, &key);
+			if (ret < 0)
+				goto out;
+		} else {
+			up_read(&fs_info->commit_root_sem);
+		}
+
 		ret = btrfs_next_item(send_root, path);
 		if (ret < 0)
 			goto out;
@@ -6689,6 +6858,20 @@
 	return ret;
 }
 
+static int replace_node_with_clone(struct btrfs_path *path, int level)
+{
+	struct extent_buffer *clone;
+
+	clone = btrfs_clone_extent_buffer(path->nodes[level]);
+	if (!clone)
+		return -ENOMEM;
+
+	free_extent_buffer(path->nodes[level]);
+	path->nodes[level] = clone;
+
+	return 0;
+}
+
 static int tree_move_down(struct btrfs_path *path, int *level, u64 reada_min_gen)
 {
 	struct extent_buffer *eb;
@@ -6698,7 +6881,9 @@
 	u64 reada_max;
 	u64 reada_done = 0;
 
-	BUG_ON(*level == 0);
+	lockdep_assert_held_read(&parent->fs_info->commit_root_sem);
+	ASSERT(*level != 0);
+
 	eb = btrfs_read_node_slot(parent, slot);
 	if (IS_ERR(eb))
 		return PTR_ERR(eb);
@@ -6721,6 +6906,10 @@
 	path->nodes[*level - 1] = eb;
 	path->slots[*level - 1] = 0;
 	(*level)--;
+
+	if (*level == 0)
+		return replace_node_with_clone(path, 0);
+
 	return 0;
 }
 
@@ -6734,8 +6923,10 @@
 	path->slots[*level]++;
 
 	while (path->slots[*level] >= nritems) {
-		if (*level == root_level)
+		if (*level == root_level) {
+			path->slots[*level] = nritems - 1;
 			return -1;
+		}
 
 		/* move upnext */
 		path->slots[*level] = 0;
@@ -6767,14 +6958,20 @@
 	} else {
 		ret = tree_move_down(path, level, reada_min_gen);
 	}
-	if (ret >= 0) {
-		if (*level == 0)
-			btrfs_item_key_to_cpu(path->nodes[*level], key,
-					path->slots[*level]);
-		else
-			btrfs_node_key_to_cpu(path->nodes[*level], key,
-					path->slots[*level]);
-	}
+
+	/*
+	 * Even if we have reached the end of a tree, ret is -1, update the key
+	 * anyway, so that in case we need to restart due to a block group
+	 * relocation, we can assert that the last key of the root node still
+	 * exists in the tree.
+	 */
+	if (*level == 0)
+		btrfs_item_key_to_cpu(path->nodes[*level], key,
+				      path->slots[*level]);
+	else
+		btrfs_node_key_to_cpu(path->nodes[*level], key,
+				      path->slots[*level]);
+
 	return ret;
 }
 
@@ -6804,6 +7001,97 @@
 }
 
 /*
+ * A transaction used for relocating a block group was committed or is about to
+ * finish its commit. Release our paths and restart the search, so that we are
+ * not using stale extent buffers:
+ *
+ * 1) For levels > 0, we are only holding references of extent buffers, without
+ *    any locks on them, which does not prevent them from having been relocated
+ *    and reallocated after the last time we released the commit root semaphore.
+ *    The exception are the root nodes, for which we always have a clone, see
+ *    the comment at btrfs_compare_trees();
+ *
+ * 2) For leaves, level 0, we are holding copies (clones) of extent buffers, so
+ *    we are safe from the concurrent relocation and reallocation. However they
+ *    can have file extent items with a pre relocation disk_bytenr value, so we
+ *    restart the start from the current commit roots and clone the new leaves so
+ *    that we get the post relocation disk_bytenr values. Not doing so, could
+ *    make us clone the wrong data in case there are new extents using the old
+ *    disk_bytenr that happen to be shared.
+ */
+static int restart_after_relocation(struct btrfs_path *left_path,
+				    struct btrfs_path *right_path,
+				    const struct btrfs_key *left_key,
+				    const struct btrfs_key *right_key,
+				    int left_level,
+				    int right_level,
+				    const struct send_ctx *sctx)
+{
+	int root_level;
+	int ret;
+
+	lockdep_assert_held_read(&sctx->send_root->fs_info->commit_root_sem);
+
+	btrfs_release_path(left_path);
+	btrfs_release_path(right_path);
+
+	/*
+	 * Since keys can not be added or removed to/from our roots because they
+	 * are readonly and we do not allow deduplication to run in parallel
+	 * (which can add, remove or change keys), the layout of the trees should
+	 * not change.
+	 */
+	left_path->lowest_level = left_level;
+	ret = search_key_again(sctx, sctx->send_root, left_path, left_key);
+	if (ret < 0)
+		return ret;
+
+	right_path->lowest_level = right_level;
+	ret = search_key_again(sctx, sctx->parent_root, right_path, right_key);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * If the lowest level nodes are leaves, clone them so that they can be
+	 * safely used by changed_cb() while not under the protection of the
+	 * commit root semaphore, even if relocation and reallocation happens in
+	 * parallel.
+	 */
+	if (left_level == 0) {
+		ret = replace_node_with_clone(left_path, 0);
+		if (ret < 0)
+			return ret;
+	}
+
+	if (right_level == 0) {
+		ret = replace_node_with_clone(right_path, 0);
+		if (ret < 0)
+			return ret;
+	}
+
+	/*
+	 * Now clone the root nodes (unless they happen to be the leaves we have
+	 * already cloned). This is to protect against concurrent snapshotting of
+	 * the send and parent roots (see the comment at btrfs_compare_trees()).
+	 */
+	root_level = btrfs_header_level(sctx->send_root->commit_root);
+	if (root_level > 0) {
+		ret = replace_node_with_clone(left_path, root_level);
+		if (ret < 0)
+			return ret;
+	}
+
+	root_level = btrfs_header_level(sctx->parent_root->commit_root);
+	if (root_level > 0) {
+		ret = replace_node_with_clone(right_path, root_level);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/*
  * This function compares two trees and calls the provided callback for
  * every changed/new/deleted item it finds.
  * If shared tree blocks are encountered, whole subtrees are skipped, making
@@ -6831,10 +7119,10 @@
 	int right_root_level;
 	int left_level;
 	int right_level;
-	int left_end_reached;
-	int right_end_reached;
-	int advance_left;
-	int advance_right;
+	int left_end_reached = 0;
+	int right_end_reached = 0;
+	int advance_left = 0;
+	int advance_right = 0;
 	u64 left_blockptr;
 	u64 right_blockptr;
 	u64 left_gen;
@@ -6902,12 +7190,18 @@
 	down_read(&fs_info->commit_root_sem);
 	left_level = btrfs_header_level(left_root->commit_root);
 	left_root_level = left_level;
+	/*
+	 * We clone the root node of the send and parent roots to prevent races
+	 * with snapshot creation of these roots. Snapshot creation COWs the
+	 * root node of a tree, so after the transaction is committed the old
+	 * extent can be reallocated while this send operation is still ongoing.
+	 * So we clone them, under the commit root semaphore, to be race free.
+	 */
 	left_path->nodes[left_level] =
 			btrfs_clone_extent_buffer(left_root->commit_root);
 	if (!left_path->nodes[left_level]) {
-		up_read(&fs_info->commit_root_sem);
 		ret = -ENOMEM;
-		goto out;
+		goto out_unlock;
 	}
 
 	right_level = btrfs_header_level(right_root->commit_root);
@@ -6915,9 +7209,8 @@
 	right_path->nodes[right_level] =
 			btrfs_clone_extent_buffer(right_root->commit_root);
 	if (!right_path->nodes[right_level]) {
-		up_read(&fs_info->commit_root_sem);
 		ret = -ENOMEM;
-		goto out;
+		goto out_unlock;
 	}
 	/*
 	 * Our right root is the parent root, while the left root is the "send"
@@ -6927,7 +7220,6 @@
 	 * will need to read them at some point.
 	 */
 	reada_min_gen = btrfs_header_generation(right_root->commit_root);
-	up_read(&fs_info->commit_root_sem);
 
 	if (left_level == 0)
 		btrfs_item_key_to_cpu(left_path->nodes[left_level],
@@ -6942,11 +7234,26 @@
 		btrfs_node_key_to_cpu(right_path->nodes[right_level],
 				&right_key, right_path->slots[right_level]);
 
-	left_end_reached = right_end_reached = 0;
-	advance_left = advance_right = 0;
+	sctx->last_reloc_trans = fs_info->last_reloc_trans;
 
 	while (1) {
-		cond_resched();
+		if (need_resched() ||
+		    rwsem_is_contended(&fs_info->commit_root_sem)) {
+			up_read(&fs_info->commit_root_sem);
+			cond_resched();
+			down_read(&fs_info->commit_root_sem);
+		}
+
+		if (fs_info->last_reloc_trans > sctx->last_reloc_trans) {
+			ret = restart_after_relocation(left_path, right_path,
+						       &left_key, &right_key,
+						       left_level, right_level,
+						       sctx);
+			if (ret < 0)
+				goto out_unlock;
+			sctx->last_reloc_trans = fs_info->last_reloc_trans;
+		}
+
 		if (advance_left && !left_end_reached) {
 			ret = tree_advance(left_path, &left_level,
 					left_root_level,
@@ -6955,7 +7262,7 @@
 			if (ret == -1)
 				left_end_reached = ADVANCE;
 			else if (ret < 0)
-				goto out;
+				goto out_unlock;
 			advance_left = 0;
 		}
 		if (advance_right && !right_end_reached) {
@@ -6966,54 +7273,55 @@
 			if (ret == -1)
 				right_end_reached = ADVANCE;
 			else if (ret < 0)
-				goto out;
+				goto out_unlock;
 			advance_right = 0;
 		}
 
 		if (left_end_reached && right_end_reached) {
 			ret = 0;
-			goto out;
+			goto out_unlock;
 		} else if (left_end_reached) {
 			if (right_level == 0) {
+				up_read(&fs_info->commit_root_sem);
 				ret = changed_cb(left_path, right_path,
 						&right_key,
 						BTRFS_COMPARE_TREE_DELETED,
 						sctx);
 				if (ret < 0)
 					goto out;
+				down_read(&fs_info->commit_root_sem);
 			}
 			advance_right = ADVANCE;
 			continue;
 		} else if (right_end_reached) {
 			if (left_level == 0) {
+				up_read(&fs_info->commit_root_sem);
 				ret = changed_cb(left_path, right_path,
 						&left_key,
 						BTRFS_COMPARE_TREE_NEW,
 						sctx);
 				if (ret < 0)
 					goto out;
+				down_read(&fs_info->commit_root_sem);
 			}
 			advance_left = ADVANCE;
 			continue;
 		}
 
 		if (left_level == 0 && right_level == 0) {
+			up_read(&fs_info->commit_root_sem);
 			cmp = btrfs_comp_cpu_keys(&left_key, &right_key);
 			if (cmp < 0) {
 				ret = changed_cb(left_path, right_path,
 						&left_key,
 						BTRFS_COMPARE_TREE_NEW,
 						sctx);
-				if (ret < 0)
-					goto out;
 				advance_left = ADVANCE;
 			} else if (cmp > 0) {
 				ret = changed_cb(left_path, right_path,
 						&right_key,
 						BTRFS_COMPARE_TREE_DELETED,
 						sctx);
-				if (ret < 0)
-					goto out;
 				advance_right = ADVANCE;
 			} else {
 				enum btrfs_compare_tree_result result;
@@ -7027,11 +7335,13 @@
 					result = BTRFS_COMPARE_TREE_SAME;
 				ret = changed_cb(left_path, right_path,
 						 &left_key, result, sctx);
-				if (ret < 0)
-					goto out;
 				advance_left = ADVANCE;
 				advance_right = ADVANCE;
 			}
+
+			if (ret < 0)
+				goto out;
+			down_read(&fs_info->commit_root_sem);
 		} else if (left_level == right_level) {
 			cmp = btrfs_comp_cpu_keys(&left_key, &right_key);
 			if (cmp < 0) {
@@ -7071,6 +7381,8 @@
 		}
 	}
 
+out_unlock:
+	up_read(&fs_info->commit_root_sem);
 out:
 	btrfs_free_path(left_path);
 	btrfs_free_path(right_path);
@@ -7250,16 +7562,16 @@
 	/*
 	 * Check that we don't overflow at later allocations, we request
 	 * clone_sources_count + 1 items, and compare to unsigned long inside
-	 * access_ok.
+	 * access_ok. Also set an upper limit for allocation size so this can't
+	 * easily exhaust memory. Max number of clone sources is about 200K.
 	 */
-	if (arg->clone_sources_count >
-	    ULONG_MAX / sizeof(struct clone_root) - 1) {
+	if (arg->clone_sources_count > SZ_8M / sizeof(struct clone_root)) {
 		ret = -EINVAL;
 		goto out;
 	}
 
 	if (arg->flags & ~BTRFS_SEND_FLAG_MASK) {
-		ret = -EINVAL;
+		ret = -EOPNOTSUPP;
 		goto out;
 	}
 
@@ -7277,7 +7589,7 @@
 	sctx->flags = arg->flags;
 
 	sctx->send_filp = fget(arg->send_fd);
-	if (!sctx->send_filp) {
+	if (!sctx->send_filp || !(sctx->send_filp->f_mode & FMODE_WRITE)) {
 		ret = -EBADF;
 		goto out;
 	}
@@ -7305,8 +7617,8 @@
 	sctx->waiting_dir_moves = RB_ROOT;
 	sctx->orphan_dirs = RB_ROOT;
 
-	sctx->clone_roots = kvcalloc(sizeof(*sctx->clone_roots),
-				     arg->clone_sources_count + 1,
+	sctx->clone_roots = kvcalloc(arg->clone_sources_count + 1,
+				     sizeof(*sctx->clone_roots),
 				     GFP_KERNEL);
 	if (!sctx->clone_roots) {
 		ret = -ENOMEM;
@@ -7409,21 +7721,7 @@
 	if (ret)
 		goto out;
 
-	spin_lock(&fs_info->send_reloc_lock);
-	if (test_bit(BTRFS_FS_RELOC_RUNNING, &fs_info->flags)) {
-		spin_unlock(&fs_info->send_reloc_lock);
-		btrfs_warn_rl(fs_info,
-		"cannot run send because a relocation operation is in progress");
-		ret = -EAGAIN;
-		goto out;
-	}
-	fs_info->send_in_progress++;
-	spin_unlock(&fs_info->send_reloc_lock);
-
 	ret = send_subvol(sctx);
-	spin_lock(&fs_info->send_reloc_lock);
-	fs_info->send_in_progress--;
-	spin_unlock(&fs_info->send_reloc_lock);
 	if (ret < 0)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/space-info.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/space-info.c
@@ -1054,7 +1054,6 @@
 			trans_rsv->reserved;
 		if (block_rsv_size < space_info->bytes_may_use)
 			delalloc_size = space_info->bytes_may_use - block_rsv_size;
-		spin_unlock(&space_info->lock);
 
 		/*
 		 * We don't want to include the global_rsv in our calculation,
@@ -1085,6 +1084,8 @@
 			flush = FLUSH_DELAYED_REFS_NR;
 		}
 
+		spin_unlock(&space_info->lock);
+
 		/*
 		 * We don't want to reclaim everything, just a portion, so scale
 		 * down the to_reclaim by 1/4.  If it takes us down to 0,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/super.c
@@ -574,6 +574,7 @@
 	int saved_compress_level;
 	bool saved_compress_force;
 	int no_compress = 0;
+	const bool remounting = test_bit(BTRFS_FS_STATE_REMOUNTING, &info->fs_state);
 
 	if (btrfs_fs_compat_ro(info, FREE_SPACE_TREE))
 		btrfs_set_opt(info->mount_opt, FREE_SPACE_TREE);
@@ -712,6 +713,8 @@
 				compress_force = false;
 				no_compress++;
 			} else {
+				btrfs_err(info, "unrecognized compression value %s",
+					  args[0].from);
 				ret = -EINVAL;
 				goto out;
 			}
@@ -770,8 +773,11 @@
 		case Opt_thread_pool:
 			ret = match_int(&args[0], &intarg);
 			if (ret) {
+				btrfs_err(info, "unrecognized thread_pool value %s",
+					  args[0].from);
 				goto out;
 			} else if (intarg == 0) {
+				btrfs_err(info, "invalid value 0 for thread_pool");
 				ret = -EINVAL;
 				goto out;
 			}
@@ -832,8 +838,11 @@
 			break;
 		case Opt_ratio:
 			ret = match_int(&args[0], &intarg);
-			if (ret)
+			if (ret) {
+				btrfs_err(info, "unrecognized metadata_ratio value %s",
+					  args[0].from);
 				goto out;
+			}
 			info->metadata_ratio = intarg;
 			btrfs_info(info, "metadata ratio %u",
 				   info->metadata_ratio);
@@ -850,6 +859,8 @@
 				btrfs_set_and_info(info, DISCARD_ASYNC,
 						   "turning on async discard");
 			} else {
+				btrfs_err(info, "unrecognized discard mode value %s",
+					  args[0].from);
 				ret = -EINVAL;
 				goto out;
 			}
@@ -874,6 +885,8 @@
 				btrfs_set_and_info(info, FREE_SPACE_TREE,
 						   "enabling free space tree");
 			} else {
+				btrfs_err(info, "unrecognized space_cache value %s",
+					  args[0].from);
 				ret = -EINVAL;
 				goto out;
 			}
@@ -943,8 +956,12 @@
 			break;
 		case Opt_check_integrity_print_mask:
 			ret = match_int(&args[0], &intarg);
-			if (ret)
+			if (ret) {
+				btrfs_err(info,
+				"unrecognized check_integrity_print_mask value %s",
+					args[0].from);
 				goto out;
+			}
 			info->check_integrity_print_mask = intarg;
 			btrfs_info(info, "check_integrity_print_mask 0x%x",
 				   info->check_integrity_print_mask);
@@ -959,13 +976,15 @@
 			goto out;
 #endif
 		case Opt_fatal_errors:
-			if (strcmp(args[0].from, "panic") == 0)
+			if (strcmp(args[0].from, "panic") == 0) {
 				btrfs_set_opt(info->mount_opt,
 					      PANIC_ON_FATAL_ERROR);
-			else if (strcmp(args[0].from, "bug") == 0)
+			} else if (strcmp(args[0].from, "bug") == 0) {
 				btrfs_clear_opt(info->mount_opt,
 					      PANIC_ON_FATAL_ERROR);
-			else {
+			} else {
+				btrfs_err(info, "unrecognized fatal_errors value %s",
+					  args[0].from);
 				ret = -EINVAL;
 				goto out;
 			}
@@ -973,8 +992,12 @@
 		case Opt_commit_interval:
 			intarg = 0;
 			ret = match_int(&args[0], &intarg);
-			if (ret)
+			if (ret) {
+				btrfs_err(info, "unrecognized commit_interval value %s",
+					  args[0].from);
+				ret = -EINVAL;
 				goto out;
+			}
 			if (intarg == 0) {
 				btrfs_info(info,
 					   "using default commit interval %us",
@@ -988,8 +1011,11 @@
 			break;
 		case Opt_rescue:
 			ret = parse_rescue_options(info, args[0].from);
-			if (ret < 0)
+			if (ret < 0) {
+				btrfs_err(info, "unrecognized rescue value %s",
+					  args[0].from);
 				goto out;
+			}
 			break;
 #ifdef CONFIG_BTRFS_DEBUG
 		case Opt_fragment_all:
@@ -1040,10 +1066,12 @@
 	}
 	if (!ret)
 		ret = btrfs_check_mountopts_zoned(info);
-	if (!ret && btrfs_test_opt(info, SPACE_CACHE))
-		btrfs_info(info, "disk space caching is enabled");
-	if (!ret && btrfs_test_opt(info, FREE_SPACE_TREE))
-		btrfs_info(info, "using free space tree");
+	if (!ret && !remounting) {
+		if (btrfs_test_opt(info, SPACE_CACHE))
+			btrfs_info(info, "disk space caching is enabled");
+		if (btrfs_test_opt(info, FREE_SPACE_TREE))
+			btrfs_info(info, "using free space tree");
+	}
 	return ret;
 }
 
@@ -1358,7 +1386,7 @@
 
 	err = open_ctree(sb, fs_devices, (char *)data);
 	if (err) {
-		btrfs_err(fs_info, "open_ctree failed");
+		btrfs_err(fs_info, "open_ctree failed: %d", err);
 		return err;
 	}
 
@@ -1705,7 +1733,7 @@
 		goto error_close_devices;
 	}
 
-	bdev = fs_devices->latest_bdev;
+	bdev = fs_devices->latest_dev->bdev;
 	s = sget(fs_type, btrfs_test_super, btrfs_set_super, flags | SB_NOSEC,
 		 fs_info);
 	if (IS_ERR(s)) {
@@ -1721,8 +1749,6 @@
 	} else {
 		snprintf(s->s_id, sizeof(s->s_id), "%pg", bdev);
 		btrfs_sb(s)->bdev_holder = fs_type;
-		if (!strstr(crc32c_impl(), "generic"))
-			set_bit(BTRFS_FS_CSUM_IMPL_FAST, &fs_info->flags);
 		error = btrfs_fill_super(s, fs_devices, data);
 	}
 	if (!error)
@@ -1917,6 +1943,14 @@
 	if (ret)
 		goto restore;
 
+	/* V1 cache is not supported for subpage mount. */
+	if (fs_info->sectorsize < PAGE_SIZE && btrfs_test_opt(fs_info, SPACE_CACHE)) {
+		btrfs_warn(fs_info,
+	"v1 space cache is not supported for page size %lu with sectorsize %u",
+			   PAGE_SIZE, fs_info->sectorsize);
+		ret = -EINVAL;
+		goto restore;
+	}
 	btrfs_remount_begin(fs_info, old_opts, *flags);
 	btrfs_resize_thread_pool(fs_info,
 		fs_info->thread_pool_size, old_thread_pool_size);
@@ -2012,6 +2046,15 @@
 			ret = -EINVAL;
 			goto restore;
 		}
+		if (btrfs_super_compat_ro_flags(fs_info->super_copy) &
+		    ~BTRFS_FEATURE_COMPAT_RO_SUPP) {
+			btrfs_err(fs_info,
+		"can not remount read-write due to unsupported optional flags 0x%llx",
+				btrfs_super_compat_ro_flags(fs_info->super_copy) &
+				~BTRFS_FEATURE_COMPAT_RO_SUPP);
+			ret = -EINVAL;
+			goto restore;
+		}
 		if (fs_info->fs_devices->rw_devices == 0) {
 			ret = -EACCES;
 			goto restore;
@@ -2321,7 +2364,7 @@
 	 * calculated f_bavail.
 	 */
 	if (!mixed && block_rsv->space_info->full &&
-	    total_free_meta - thresh < block_rsv->size)
+	    (total_free_meta < thresh || total_free_meta - thresh < block_rsv->size))
 		buf->f_bavail = 0;
 
 	buf->f_type = BTRFS_SUPER_MAGIC;
@@ -2452,41 +2495,103 @@
 	return btrfs_commit_transaction(trans);
 }
 
+static int check_dev_super(struct btrfs_device *dev)
+{
+	struct btrfs_fs_info *fs_info = dev->fs_info;
+	struct btrfs_super_block *sb;
+	u16 csum_type;
+	int ret = 0;
+
+	/* This should be called with fs still frozen. */
+	ASSERT(test_bit(BTRFS_FS_FROZEN, &fs_info->flags));
+
+	/* Missing dev, no need to check. */
+	if (!dev->bdev)
+		return 0;
+
+	/* Only need to check the primary super block. */
+	sb = btrfs_read_dev_one_super(dev->bdev, 0, true);
+	if (IS_ERR(sb))
+		return PTR_ERR(sb);
+
+	/* Verify the checksum. */
+	csum_type = btrfs_super_csum_type(sb);
+	if (csum_type != btrfs_super_csum_type(fs_info->super_copy)) {
+		btrfs_err(fs_info, "csum type changed, has %u expect %u",
+			  csum_type, btrfs_super_csum_type(fs_info->super_copy));
+		ret = -EUCLEAN;
+		goto out;
+	}
+
+	if (btrfs_check_super_csum(fs_info, sb)) {
+		btrfs_err(fs_info, "csum for on-disk super block no longer matches");
+		ret = -EUCLEAN;
+		goto out;
+	}
+
+	/* Btrfs_validate_super() includes fsid check against super->fsid. */
+	ret = btrfs_validate_super(fs_info, sb, 0);
+	if (ret < 0)
+		goto out;
+
+	if (btrfs_super_generation(sb) != fs_info->last_trans_committed) {
+		btrfs_err(fs_info, "transid mismatch, has %llu expect %llu",
+			btrfs_super_generation(sb),
+			fs_info->last_trans_committed);
+		ret = -EUCLEAN;
+		goto out;
+	}
+out:
+	btrfs_release_disk_super(sb);
+	return ret;
+}
+
 static int btrfs_unfreeze(struct super_block *sb)
 {
 	struct btrfs_fs_info *fs_info = btrfs_sb(sb);
+	struct btrfs_device *device;
+	int ret = 0;
 
+	/*
+	 * Make sure the fs is not changed by accident (like hibernation then
+	 * modified by other OS).
+	 * If we found anything wrong, we mark the fs error immediately.
+	 *
+	 * And since the fs is frozen, no one can modify the fs yet, thus
+	 * we don't need to hold device_list_mutex.
+	 */
+	list_for_each_entry(device, &fs_info->fs_devices->devices, dev_list) {
+		ret = check_dev_super(device);
+		if (ret < 0) {
+			btrfs_handle_fs_error(fs_info, ret,
+				"super block on devid %llu got modified unexpectedly",
+				device->devid);
+			break;
+		}
+	}
 	clear_bit(BTRFS_FS_FROZEN, &fs_info->flags);
+
+	/*
+	 * We still return 0, to allow VFS layer to unfreeze the fs even the
+	 * above checks failed. Since the fs is either fine or read-only, we're
+	 * safe to continue, without causing further damage.
+	 */
 	return 0;
 }
 
 static int btrfs_show_devname(struct seq_file *m, struct dentry *root)
 {
 	struct btrfs_fs_info *fs_info = btrfs_sb(root->d_sb);
-	struct btrfs_device *dev, *first_dev = NULL;
 
 	/*
-	 * Lightweight locking of the devices. We should not need
-	 * device_list_mutex here as we only read the device data and the list
-	 * is protected by RCU.  Even if a device is deleted during the list
-	 * traversals, we'll get valid data, the freeing callback will wait at
-	 * least until the rcu_read_unlock.
+	 * There should be always a valid pointer in latest_dev, it may be stale
+	 * for a short moment in case it's being deleted but still valid until
+	 * the end of RCU grace period.
 	 */
 	rcu_read_lock();
-	list_for_each_entry_rcu(dev, &fs_info->fs_devices->devices, dev_list) {
-		if (test_bit(BTRFS_DEV_STATE_MISSING, &dev->dev_state))
-			continue;
-		if (!dev->name)
-			continue;
-		if (!first_dev || dev->devid < first_dev->devid)
-			first_dev = dev;
-	}
-
-	if (first_dev)
-		seq_escape(m, rcu_str_deref(first_dev->name), " \t\n\\");
-	else
-		WARN_ON(1);
+	seq_escape(m, rcu_str_deref(fs_info->fs_devices->latest_dev->name), " \t\n\\");
 	rcu_read_unlock();
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/sysfs.c
@@ -177,7 +177,7 @@
 	} else
 		val = can_modify_feature(fa);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n", val);
+	return sysfs_emit(buf, "%d\n", val);
 }
 
 static ssize_t btrfs_feature_attr_store(struct kobject *kobj,
@@ -283,9 +283,11 @@
 BTRFS_FEAT_ATTR_INCOMPAT(metadata_uuid, METADATA_UUID);
 BTRFS_FEAT_ATTR_COMPAT_RO(free_space_tree, FREE_SPACE_TREE);
 BTRFS_FEAT_ATTR_INCOMPAT(raid1c34, RAID1C34);
-/* Remove once support for zoned allocation is feature complete */
 #ifdef CONFIG_BTRFS_DEBUG
+/* Remove once support for zoned allocation is feature complete */
 BTRFS_FEAT_ATTR_INCOMPAT(zoned, ZONED);
+/* Remove once support for extent tree v2 is feature complete */
+BTRFS_FEAT_ATTR_INCOMPAT(extent_tree_v2, EXTENT_TREE_V2);
 #endif
 #ifdef CONFIG_FS_VERITY
 BTRFS_FEAT_ATTR_COMPAT_RO(verity, VERITY);
@@ -314,6 +316,7 @@
 	BTRFS_FEAT_ATTR_PTR(raid1c34),
 #ifdef CONFIG_BTRFS_DEBUG
 	BTRFS_FEAT_ATTR_PTR(zoned),
+	BTRFS_FEAT_ATTR_PTR(extent_tree_v2),
 #endif
 #ifdef CONFIG_FS_VERITY
 	BTRFS_FEAT_ATTR_PTR(verity),
@@ -330,7 +333,7 @@
 static ssize_t rmdir_subvol_show(struct kobject *kobj,
 				 struct kobj_attribute *ka, char *buf)
 {
-	return scnprintf(buf, PAGE_SIZE, "0\n");
+	return sysfs_emit(buf, "0\n");
 }
 BTRFS_ATTR(static_feature, rmdir_subvol, rmdir_subvol_show);
 
@@ -345,12 +348,12 @@
 		 * This "trick" only works as long as 'enum btrfs_csum_type' has
 		 * no holes in it
 		 */
-		ret += scnprintf(buf + ret, PAGE_SIZE - ret, "%s%s",
-				(i == 0 ? "" : " "), btrfs_super_csum_name(i));
+		ret += sysfs_emit_at(buf, ret, "%s%s", (i == 0 ? "" : " "),
+				     btrfs_super_csum_name(i));
 
 	}
 
-	ret += scnprintf(buf + ret, PAGE_SIZE - ret, "\n");
+	ret += sysfs_emit_at(buf, ret, "\n");
 	return ret;
 }
 BTRFS_ATTR(static_feature, supported_checksums, supported_checksums_show);
@@ -358,7 +361,7 @@
 static ssize_t send_stream_version_show(struct kobject *kobj,
 					struct kobj_attribute *ka, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%d\n", BTRFS_SEND_STREAM_VERSION);
+	return sysfs_emit(buf, "%d\n", BTRFS_SEND_STREAM_VERSION);
 }
 BTRFS_ATTR(static_feature, send_stream_version, send_stream_version_show);
 
@@ -378,9 +381,8 @@
 	int i;
 
 	for (i = 0; i < ARRAY_SIZE(rescue_opts); i++)
-		ret += scnprintf(buf + ret, PAGE_SIZE - ret, "%s%s",
-				 (i ? " " : ""), rescue_opts[i]);
-	ret += scnprintf(buf + ret, PAGE_SIZE - ret, "\n");
+		ret += sysfs_emit_at(buf, ret, "%s%s", (i ? " " : ""), rescue_opts[i]);
+	ret += sysfs_emit_at(buf, ret, "\n");
 	return ret;
 }
 BTRFS_ATTR(static_feature, supported_rescue_options,
@@ -394,10 +396,10 @@
 
 	/* 4K sector size is also supported with 64K page size */
 	if (PAGE_SIZE == SZ_64K)
-		ret += scnprintf(buf + ret, PAGE_SIZE - ret, "%u ", SZ_4K);
+		ret += sysfs_emit_at(buf, ret, "%u ", SZ_4K);
 
 	/* Only sectorsize == PAGE_SIZE is now supported */
-	ret += scnprintf(buf + ret, PAGE_SIZE - ret, "%lu\n", PAGE_SIZE);
+	ret += sysfs_emit_at(buf, ret, "%lu\n", PAGE_SIZE);
 
 	return ret;
 }
@@ -437,7 +439,7 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%lld\n",
+	return sysfs_emit(buf, "%lld\n",
 			atomic64_read(&fs_info->discard_ctl.discardable_bytes));
 }
 BTRFS_ATTR(discard, discardable_bytes, btrfs_discardable_bytes_show);
@@ -448,7 +450,7 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n",
+	return sysfs_emit(buf, "%d\n",
 			atomic_read(&fs_info->discard_ctl.discardable_extents));
 }
 BTRFS_ATTR(discard, discardable_extents, btrfs_discardable_extents_show);
@@ -459,8 +461,8 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%llu\n",
-			fs_info->discard_ctl.discard_bitmap_bytes);
+	return sysfs_emit(buf, "%llu\n",
+			  fs_info->discard_ctl.discard_bitmap_bytes);
 }
 BTRFS_ATTR(discard, discard_bitmap_bytes, btrfs_discard_bitmap_bytes_show);
 
@@ -470,7 +472,7 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%lld\n",
+	return sysfs_emit(buf, "%lld\n",
 		atomic64_read(&fs_info->discard_ctl.discard_bytes_saved));
 }
 BTRFS_ATTR(discard, discard_bytes_saved, btrfs_discard_bytes_saved_show);
@@ -481,8 +483,8 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%llu\n",
-			fs_info->discard_ctl.discard_extent_bytes);
+	return sysfs_emit(buf, "%llu\n",
+			  fs_info->discard_ctl.discard_extent_bytes);
 }
 BTRFS_ATTR(discard, discard_extent_bytes, btrfs_discard_extent_bytes_show);
 
@@ -492,8 +494,8 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n",
-			READ_ONCE(fs_info->discard_ctl.iops_limit));
+	return sysfs_emit(buf, "%u\n",
+			  READ_ONCE(fs_info->discard_ctl.iops_limit));
 }
 
 static ssize_t btrfs_discard_iops_limit_store(struct kobject *kobj,
@@ -523,8 +525,8 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n",
-			READ_ONCE(fs_info->discard_ctl.kbps_limit));
+	return sysfs_emit(buf, "%u\n",
+			  READ_ONCE(fs_info->discard_ctl.kbps_limit));
 }
 
 static ssize_t btrfs_discard_kbps_limit_store(struct kobject *kobj,
@@ -553,8 +555,8 @@
 {
 	struct btrfs_fs_info *fs_info = discard_to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%llu\n",
-			READ_ONCE(fs_info->discard_ctl.max_discard_size));
+	return sysfs_emit(buf, "%llu\n",
+			  READ_ONCE(fs_info->discard_ctl.max_discard_size));
 }
 
 static ssize_t btrfs_discard_max_discard_size_store(struct kobject *kobj,
@@ -627,7 +629,7 @@
 	val = *value_ptr;
 	if (lock)
 		spin_unlock(lock);
-	return scnprintf(buf, PAGE_SIZE, "%llu\n", val);
+	return sysfs_emit(buf, "%llu\n", val);
 }
 
 static ssize_t global_rsv_size_show(struct kobject *kobj,
@@ -673,7 +675,7 @@
 			val += block_group->used;
 	}
 	up_read(&sinfo->groups_sem);
-	return scnprintf(buf, PAGE_SIZE, "%llu\n", val);
+	return sysfs_emit(buf, "%llu\n", val);
 }
 
 /*
@@ -771,7 +773,7 @@
 	ssize_t ret;
 
 	spin_lock(&fs_info->super_lock);
-	ret = scnprintf(buf, PAGE_SIZE, label[0] ? "%s\n" : "%s", label);
+	ret = sysfs_emit(buf, label[0] ? "%s\n" : "%s", label);
 	spin_unlock(&fs_info->super_lock);
 
 	return ret;
@@ -819,7 +821,7 @@
 {
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n", fs_info->super_copy->nodesize);
+	return sysfs_emit(buf, "%u\n", fs_info->nodesize);
 }
 
 BTRFS_ATTR(, nodesize, btrfs_nodesize_show);
@@ -829,8 +831,7 @@
 {
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n",
-			 fs_info->super_copy->sectorsize);
+	return sysfs_emit(buf, "%u\n", fs_info->sectorsize);
 }
 
 BTRFS_ATTR(, sectorsize, btrfs_sectorsize_show);
@@ -840,7 +841,7 @@
 {
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%u\n", fs_info->super_copy->sectorsize);
+	return sysfs_emit(buf, "%u\n", fs_info->sectorsize);
 }
 
 BTRFS_ATTR(, clone_alignment, btrfs_clone_alignment_show);
@@ -852,7 +853,7 @@
 	int quota_override;
 
 	quota_override = test_bit(BTRFS_FS_QUOTA_OVERRIDE, &fs_info->flags);
-	return scnprintf(buf, PAGE_SIZE, "%d\n", quota_override);
+	return sysfs_emit(buf, "%d\n", quota_override);
 }
 
 static ssize_t quota_override_store(struct kobject *kobj,
@@ -890,8 +891,7 @@
 {
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%pU\n",
-			fs_info->fs_devices->metadata_uuid);
+	return sysfs_emit(buf, "%pU\n", fs_info->fs_devices->metadata_uuid);
 }
 
 BTRFS_ATTR(, metadata_uuid, btrfs_metadata_uuid_show);
@@ -902,9 +902,9 @@
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 	u16 csum_type = btrfs_super_csum_type(fs_info->super_copy);
 
-	return scnprintf(buf, PAGE_SIZE, "%s (%s)\n",
-			btrfs_super_csum_name(csum_type),
-			crypto_shash_driver_name(fs_info->csum_shash));
+	return sysfs_emit(buf, "%s (%s)\n",
+			  btrfs_super_csum_name(csum_type),
+			  crypto_shash_driver_name(fs_info->csum_shash));
 }
 
 BTRFS_ATTR(, checksum, btrfs_checksum_show);
@@ -941,7 +941,7 @@
 			str = "UNKNOWN\n";
 			break;
 	}
-	return scnprintf(buf, PAGE_SIZE, "%s", str);
+	return sysfs_emit(buf, "%s", str);
 }
 BTRFS_ATTR(, exclusive_operation, btrfs_exclusive_operation_show);
 
@@ -950,7 +950,7 @@
 {
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%llu\n", fs_info->generation);
+	return sysfs_emit(buf, "%llu\n", fs_info->generation);
 }
 BTRFS_ATTR(, generation, btrfs_generation_show);
 
@@ -1028,8 +1028,7 @@
 	struct btrfs_fs_info *fs_info = to_fs_info(kobj);
 	ssize_t ret;
 
-	ret = scnprintf(buf, PAGE_SIZE, "%d\n",
-			READ_ONCE(fs_info->bg_reclaim_threshold));
+	ret = sysfs_emit(buf, "%d\n", READ_ONCE(fs_info->bg_reclaim_threshold));
 
 	return ret;
 }
@@ -1471,7 +1470,7 @@
 
 	val = !!test_bit(BTRFS_DEV_STATE_IN_FS_METADATA, &device->dev_state);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n", val);
+	return sysfs_emit(buf, "%d\n", val);
 }
 BTRFS_ATTR(devid, in_fs_metadata, btrfs_devinfo_in_fs_metadata_show);
 
@@ -1484,7 +1483,7 @@
 
 	val = !!test_bit(BTRFS_DEV_STATE_MISSING, &device->dev_state);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n", val);
+	return sysfs_emit(buf, "%d\n", val);
 }
 BTRFS_ATTR(devid, missing, btrfs_devinfo_missing_show);
 
@@ -1498,7 +1497,7 @@
 
 	val = !!test_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n", val);
+	return sysfs_emit(buf, "%d\n", val);
 }
 BTRFS_ATTR(devid, replace_target, btrfs_devinfo_replace_target_show);
 
@@ -1509,8 +1508,7 @@
 	struct btrfs_device *device = container_of(kobj, struct btrfs_device,
 						   devid_kobj);
 
-	return scnprintf(buf, PAGE_SIZE, "%llu\n",
-			 READ_ONCE(device->scrub_speed_max));
+	return sysfs_emit(buf, "%llu\n", READ_ONCE(device->scrub_speed_max));
 }
 
 static ssize_t btrfs_devinfo_scrub_speed_max_store(struct kobject *kobj,
@@ -1523,6 +1521,10 @@
 	unsigned long long limit;
 
 	limit = memparse(buf, &endptr);
+	/* There could be trailing '\n', also catch any typos after the value. */
+	endptr = skip_spaces(endptr);
+	if (*endptr != 0)
+		return -EINVAL;
 	WRITE_ONCE(device->scrub_speed_max, limit);
 	return len;
 }
@@ -1538,7 +1540,7 @@
 
 	val = !!test_bit(BTRFS_DEV_STATE_WRITEABLE, &device->dev_state);
 
-	return scnprintf(buf, PAGE_SIZE, "%d\n", val);
+	return sysfs_emit(buf, "%d\n", val);
 }
 BTRFS_ATTR(devid, writeable, btrfs_devinfo_writeable_show);
 
@@ -1549,14 +1551,14 @@
 						   devid_kobj);
 
 	if (!device->dev_stats_valid)
-		return scnprintf(buf, PAGE_SIZE, "invalid\n");
+		return sysfs_emit(buf, "invalid\n");
 
 	/*
 	 * Print all at once so we get a snapshot of all values from the same
 	 * time. Keep them in sync and in order of definition of
 	 * btrfs_dev_stat_values.
 	 */
-	return scnprintf(buf, PAGE_SIZE,
+	return sysfs_emit(buf,
 		"write_errs %d\n"
 		"read_errs %d\n"
 		"flush_errs %d\n"
@@ -2035,8 +2037,11 @@
 
 #ifdef CONFIG_BTRFS_DEBUG
 	ret = sysfs_create_group(&btrfs_kset->kobj, &btrfs_debug_feature_attr_group);
-	if (ret)
-		goto out2;
+	if (ret) {
+		sysfs_unmerge_group(&btrfs_kset->kobj,
+				    &btrfs_static_feature_attr_group);
+		goto out_remove_group;
+	}
 #endif
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/tests/btrfs-tests.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/tests/btrfs-tests.c
@@ -199,7 +199,7 @@
 
 void btrfs_free_dummy_root(struct btrfs_root *root)
 {
-	if (!root)
+	if (IS_ERR_OR_NULL(root))
 		return;
 	/* Will be freed by btrfs_free_fs_roots */
 	if (WARN_ON(test_bit(BTRFS_ROOT_IN_RADIX, &root->state)))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/tests/qgroup-tests.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/tests/qgroup-tests.c
@@ -225,20 +225,20 @@
 	 */
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &old_roots, false);
 	if (ret) {
-		ulist_free(old_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
 
 	ret = insert_normal_tree_ref(root, nodesize, nodesize, 0,
 				BTRFS_FS_TREE_OBJECTID);
-	if (ret)
+	if (ret) {
+		ulist_free(old_roots);
 		return ret;
+	}
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &new_roots, false);
 	if (ret) {
 		ulist_free(old_roots);
-		ulist_free(new_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
@@ -250,29 +250,31 @@
 		return ret;
 	}
 
+	/* btrfs_qgroup_account_extent() always frees the ulists passed to it. */
+	old_roots = NULL;
+	new_roots = NULL;
+
 	if (btrfs_verify_qgroup_counts(fs_info, BTRFS_FS_TREE_OBJECTID,
 				nodesize, nodesize)) {
 		test_err("qgroup counts didn't match expected values");
 		return -EINVAL;
 	}
-	old_roots = NULL;
-	new_roots = NULL;
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &old_roots, false);
 	if (ret) {
-		ulist_free(old_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
 
 	ret = remove_extent_item(root, nodesize, nodesize);
-	if (ret)
+	if (ret) {
+		ulist_free(old_roots);
 		return -EINVAL;
+	}
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &new_roots, false);
 	if (ret) {
 		ulist_free(old_roots);
-		ulist_free(new_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
@@ -322,20 +324,20 @@
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &old_roots, false);
 	if (ret) {
-		ulist_free(old_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
 
 	ret = insert_normal_tree_ref(root, nodesize, nodesize, 0,
 				BTRFS_FS_TREE_OBJECTID);
-	if (ret)
+	if (ret) {
+		ulist_free(old_roots);
 		return ret;
+	}
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &new_roots, false);
 	if (ret) {
 		ulist_free(old_roots);
-		ulist_free(new_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
@@ -355,20 +357,20 @@
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &old_roots, false);
 	if (ret) {
-		ulist_free(old_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
 
 	ret = add_tree_ref(root, nodesize, nodesize, 0,
 			BTRFS_FIRST_FREE_OBJECTID);
-	if (ret)
+	if (ret) {
+		ulist_free(old_roots);
 		return ret;
+	}
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &new_roots, false);
 	if (ret) {
 		ulist_free(old_roots);
-		ulist_free(new_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
@@ -394,20 +396,20 @@
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &old_roots, false);
 	if (ret) {
-		ulist_free(old_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
 
 	ret = remove_extent_ref(root, nodesize, nodesize, 0,
 				BTRFS_FIRST_FREE_OBJECTID);
-	if (ret)
+	if (ret) {
+		ulist_free(old_roots);
 		return ret;
+	}
 
 	ret = btrfs_find_all_roots(&trans, fs_info, nodesize, 0, &new_roots, false);
 	if (ret) {
 		ulist_free(old_roots);
-		ulist_free(new_roots);
 		test_err("couldn't find old roots: %d", ret);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/transaction.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/transaction.c
@@ -163,6 +163,10 @@
 	struct btrfs_caching_control *caching_ctl, *next;
 
 	down_write(&fs_info->commit_root_sem);
+
+	if (test_bit(BTRFS_FS_RELOC_RUNNING, &fs_info->flags))
+		fs_info->last_reloc_trans = trans->transid;
+
 	list_for_each_entry_safe(root, tmp, &cur_trans->switch_commits,
 				 dirty_list) {
 		list_del_init(&root->dirty_list);
@@ -291,8 +295,10 @@
 	cur_trans = fs_info->running_transaction;
 	if (cur_trans) {
 		if (TRANS_ABORTED(cur_trans)) {
+			const int abort_error = cur_trans->aborted;
+
 			spin_unlock(&fs_info->trans_lock);
-			return cur_trans->aborted;
+			return abort_error;
 		}
 		if (btrfs_blocked_trans_types[cur_trans->state] & type) {
 			spin_unlock(&fs_info->trans_lock);
@@ -307,10 +313,11 @@
 	spin_unlock(&fs_info->trans_lock);
 
 	/*
-	 * If we are ATTACH, we just want to catch the current transaction,
-	 * and commit it. If there is no transaction, just return ENOENT.
+	 * If we are ATTACH or TRANS_JOIN_NOSTART, we just want to catch the
+	 * current transaction, and commit it. If there is no transaction, just
+	 * return ENOENT.
 	 */
-	if (type == TRANS_ATTACH)
+	if (type == TRANS_ATTACH || type == TRANS_JOIN_NOSTART)
 		return -ENOENT;
 
 	/*
@@ -836,8 +843,13 @@
 
 	trans = start_transaction(root, 0, TRANS_ATTACH,
 				  BTRFS_RESERVE_NO_FLUSH, true);
-	if (trans == ERR_PTR(-ENOENT))
-		btrfs_wait_for_commit(root->fs_info, 0);
+	if (trans == ERR_PTR(-ENOENT)) {
+		int ret;
+
+		ret = btrfs_wait_for_commit(root->fs_info, 0);
+		if (ret)
+			return ERR_PTR(ret);
+	}
 
 	return trans;
 }
@@ -846,7 +858,37 @@
 static noinline void wait_for_commit(struct btrfs_transaction *commit,
 				     const enum btrfs_trans_state min_state)
 {
-	wait_event(commit->commit_wait, commit->state >= min_state);
+	struct btrfs_fs_info *fs_info = commit->fs_info;
+	u64 transid = commit->transid;
+	bool put = false;
+
+	while (1) {
+		wait_event(commit->commit_wait, commit->state >= min_state);
+		if (put)
+			btrfs_put_transaction(commit);
+
+		if (min_state < TRANS_STATE_COMPLETED)
+			break;
+
+		/*
+		 * A transaction isn't really completed until all of the
+		 * previous transactions are completed, but with fsync we can
+		 * end up with SUPER_COMMITTED transactions before a COMPLETED
+		 * transaction. Wait for those.
+		 */
+
+		spin_lock(&fs_info->trans_lock);
+		commit = list_first_entry_or_null(&fs_info->trans_list,
+						  struct btrfs_transaction,
+						  list);
+		if (!commit || commit->transid > transid) {
+			spin_unlock(&fs_info->trans_lock);
+			break;
+		}
+		refcount_inc(&commit->use_count);
+		put = true;
+		spin_unlock(&fs_info->trans_lock);
+	}
 }
 
 int btrfs_wait_for_commit(struct btrfs_fs_info *fs_info, u64 transid)
@@ -902,6 +944,7 @@
 	}
 
 	wait_for_commit(cur_trans, TRANS_STATE_COMPLETED);
+	ret = cur_trans->aborted;
 	btrfs_put_transaction(cur_trans);
 out:
 	return ret;
@@ -1311,6 +1354,32 @@
 }
 
 /*
+ * If we had a pending drop we need to see if there are any others left in our
+ * dead roots list, and if not clear our bit and wake any waiters.
+ */
+void btrfs_maybe_wake_unfinished_drop(struct btrfs_fs_info *fs_info)
+{
+	/*
+	 * We put the drop in progress roots at the front of the list, so if the
+	 * first entry doesn't have UNFINISHED_DROP set we can wake everybody
+	 * up.
+	 */
+	spin_lock(&fs_info->trans_lock);
+	if (!list_empty(&fs_info->dead_roots)) {
+		struct btrfs_root *root = list_first_entry(&fs_info->dead_roots,
+							   struct btrfs_root,
+							   root_list);
+		if (test_bit(BTRFS_ROOT_UNFINISHED_DROP, &root->state)) {
+			spin_unlock(&fs_info->trans_lock);
+			return;
+		}
+	}
+	spin_unlock(&fs_info->trans_lock);
+
+	btrfs_wake_unfinished_drop(fs_info);
+}
+
+/*
  * dead roots are old snapshots that need to be deleted.  This allocates
  * a dirty root struct and adds it into the list of dead roots that need to
  * be deleted
@@ -1322,7 +1391,12 @@
 	spin_lock(&fs_info->trans_lock);
 	if (list_empty(&root->root_list)) {
 		btrfs_grab_root(root);
-		list_add_tail(&root->root_list, &fs_info->dead_roots);
+
+		/* We want to process the partially complete drops first. */
+		if (test_bit(BTRFS_ROOT_UNFINISHED_DROP, &root->state))
+			list_add(&root->root_list, &fs_info->dead_roots);
+		else
+			list_add_tail(&root->root_list, &fs_info->dead_roots);
 	}
 	spin_unlock(&fs_info->trans_lock);
 }
@@ -1352,6 +1426,7 @@
 			radix_tree_tag_clear(&fs_info->fs_roots_radix,
 					(unsigned long)root->root_key.objectid,
 					BTRFS_ROOT_TRANS_TAG);
+			btrfs_qgroup_free_meta_all_pertrans(root);
 			spin_unlock(&fs_info->fs_roots_radix_lock);
 
 			btrfs_free_log(trans, root);
@@ -1376,7 +1451,6 @@
 			if (ret2)
 				return ret2;
 			spin_lock(&fs_info->fs_roots_radix_lock);
-			btrfs_qgroup_free_meta_all_pertrans(root);
 		}
 	}
 	spin_unlock(&fs_info->fs_roots_radix_lock);
@@ -1717,7 +1791,7 @@
 	}
 
 	key.offset = (u64)-1;
-	pending->snap = btrfs_get_new_fs_root(fs_info, objectid, pending->anon_dev);
+	pending->snap = btrfs_get_new_fs_root(fs_info, objectid, &pending->anon_dev);
 	if (IS_ERR(pending->snap)) {
 		ret = PTR_ERR(pending->snap);
 		pending->snap = NULL;
@@ -2014,16 +2088,24 @@
 static inline int btrfs_start_delalloc_flush(struct btrfs_fs_info *fs_info)
 {
 	/*
-	 * We use writeback_inodes_sb here because if we used
+	 * We use try_to_writeback_inodes_sb() here because if we used
 	 * btrfs_start_delalloc_roots we would deadlock with fs freeze.
 	 * Currently are holding the fs freeze lock, if we do an async flush
 	 * we'll do btrfs_join_transaction() and deadlock because we need to
 	 * wait for the fs freeze lock.  Using the direct flushing we benefit
 	 * from already being in a transaction and our join_transaction doesn't
 	 * have to re-take the fs freeze lock.
+	 *
+	 * Note that try_to_writeback_inodes_sb() will only trigger writeback
+	 * if it can read lock sb->s_umount. It will always be able to lock it,
+	 * except when the filesystem is being unmounted or being frozen, but in
+	 * those cases sync_filesystem() is called, which results in calling
+	 * writeback_inodes_sb() while holding a write lock on sb->s_umount.
+	 * Note that we don't call writeback_inodes_sb() directly, because it
+	 * will emit a warning if sb->s_umount is not locked.
 	 */
 	if (btrfs_test_opt(fs_info, FLUSHONCOMMIT))
-		writeback_inodes_sb(fs_info->sb, WB_REASON_SYNC);
+		try_to_writeback_inodes_sb(fs_info->sb, WB_REASON_SYNC);
 	return 0;
 }
 
@@ -2033,6 +2115,27 @@
 		btrfs_wait_ordered_roots(fs_info, U64_MAX, 0, (u64)-1);
 }
 
+/*
+ * Add a pending snapshot associated with the given transaction handle to the
+ * respective handle. This must be called after the transaction commit started
+ * and while holding fs_info->trans_lock.
+ * This serves to guarantee a caller of btrfs_commit_transaction() that it can
+ * safely free the pending snapshot pointer in case btrfs_commit_transaction()
+ * returns an error.
+ */
+static void add_pending_snapshot(struct btrfs_trans_handle *trans)
+{
+	struct btrfs_transaction *cur_trans = trans->transaction;
+
+	if (!trans->pending_snapshot)
+		return;
+
+	lockdep_assert_held(&trans->fs_info->trans_lock);
+	ASSERT(cur_trans->state >= TRANS_STATE_COMMIT_START);
+
+	list_add(&trans->pending_snapshot->list, &cur_trans->pending_snapshots);
+}
+
 int btrfs_commit_transaction(struct btrfs_trans_handle *trans)
 {
 	struct btrfs_fs_info *fs_info = trans->fs_info;
@@ -2106,6 +2209,8 @@
 	if (cur_trans->state >= TRANS_STATE_COMMIT_START) {
 		enum btrfs_trans_state want_state = TRANS_STATE_COMPLETED;
 
+		add_pending_snapshot(trans);
+
 		spin_unlock(&fs_info->trans_lock);
 		refcount_inc(&cur_trans->use_count);
 
@@ -2196,6 +2301,7 @@
 	 * COMMIT_DOING so make sure to wait for num_writers to == 1 again.
 	 */
 	spin_lock(&fs_info->trans_lock);
+	add_pending_snapshot(trans);
 	cur_trans->state = TRANS_STATE_COMMIT_DOING;
 	spin_unlock(&fs_info->trans_lock);
 	wait_event(cur_trans->writer_wait,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/transaction.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/transaction.h
@@ -11,6 +11,12 @@
 #include "delayed-ref.h"
 #include "ctree.h"
 
+/*
+ * Signal that a direct IO write is in progress, to avoid deadlock for sync
+ * direct IO writes when fsync is called during the direct IO write path.
+ */
+#define BTRFS_TRANS_DIO_WRITE_STUB	((void *) 1)
+
 enum btrfs_trans_state {
 	TRANS_STATE_RUNNING,
 	TRANS_STATE_COMMIT_START,
@@ -123,6 +129,8 @@
 	struct btrfs_transaction *transaction;
 	struct btrfs_block_rsv *block_rsv;
 	struct btrfs_block_rsv *orig_rsv;
+	/* Set by a task that wants to create a snapshot. */
+	struct btrfs_pending_snapshot *pending_snapshot;
 	refcount_t use_count;
 	unsigned int type;
 	/*
@@ -215,6 +223,7 @@
 
 void btrfs_add_dead_root(struct btrfs_root *root);
 int btrfs_defrag_root(struct btrfs_root *root);
+void btrfs_maybe_wake_unfinished_drop(struct btrfs_fs_info *fs_info);
 int btrfs_clean_one_deleted_snapshot(struct btrfs_root *root);
 int btrfs_commit_transaction(struct btrfs_trans_handle *trans);
 int btrfs_commit_transaction_async(struct btrfs_trans_handle *trans);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/tree-checker.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/tree-checker.c
@@ -442,6 +442,20 @@
 	btrfs_item_key_to_cpu(leaf, &item_key, slot);
 	is_root_item = (item_key.type == BTRFS_ROOT_ITEM_KEY);
 
+	/*
+	 * Bad rootid for reloc trees.
+	 *
+	 * Reloc trees are only for subvolume trees, other trees only need
+	 * to be COWed to be relocated.
+	 */
+	if (unlikely(is_root_item && key->objectid == BTRFS_TREE_RELOC_OBJECTID &&
+		     !is_fstree(key->offset))) {
+		generic_err(leaf, slot,
+		"invalid reloc tree for root %lld, root id is not a subvolume tree",
+			    key->offset);
+		return -EUCLEAN;
+	}
+
 	/* No such tree id */
 	if (unlikely(key->objectid == 0)) {
 		if (is_root_item)
@@ -965,6 +979,7 @@
 			  struct btrfs_key *key, int slot)
 {
 	struct btrfs_dev_item *ditem;
+	const u32 item_size = btrfs_item_size_nr(leaf, slot);
 
 	if (unlikely(key->objectid != BTRFS_DEV_ITEMS_OBJECTID)) {
 		dev_item_err(leaf, slot,
@@ -972,6 +987,13 @@
 			     key->objectid, BTRFS_DEV_ITEMS_OBJECTID);
 		return -EUCLEAN;
 	}
+
+	if (unlikely(item_size != sizeof(*ditem))) {
+		dev_item_err(leaf, slot, "invalid item size: has %u expect %zu",
+			     item_size, sizeof(*ditem));
+		return -EUCLEAN;
+	}
+
 	ditem = btrfs_item_ptr(leaf, slot, struct btrfs_dev_item);
 	if (unlikely(btrfs_device_id(leaf, ditem) != key->offset)) {
 		dev_item_err(leaf, slot,
@@ -1007,6 +1029,7 @@
 	struct btrfs_inode_item *iitem;
 	u64 super_gen = btrfs_super_generation(fs_info->super_copy);
 	u32 valid_mask = (S_IFMT | S_ISUID | S_ISGID | S_ISVTX | 0777);
+	const u32 item_size = btrfs_item_size_nr(leaf, slot);
 	u32 mode;
 	int ret;
 	u32 flags;
@@ -1016,6 +1039,12 @@
 	if (unlikely(ret < 0))
 		return ret;
 
+	if (unlikely(item_size != sizeof(*iitem))) {
+		generic_err(leaf, slot, "invalid item size: has %u expect %zu",
+			    item_size, sizeof(*iitem));
+		return -EUCLEAN;
+	}
+
 	iitem = btrfs_item_ptr(leaf, slot, struct btrfs_inode_item);
 
 	/* Here we use super block generation + 1 to handle log tree */
@@ -1201,7 +1230,8 @@
 }
 
 static int check_extent_item(struct extent_buffer *leaf,
-			     struct btrfs_key *key, int slot)
+			     struct btrfs_key *key, int slot,
+			     struct btrfs_key *prev_key)
 {
 	struct btrfs_fs_info *fs_info = leaf->fs_info;
 	struct btrfs_extent_item *ei;
@@ -1352,7 +1382,7 @@
 		if (unlikely(ptr + btrfs_extent_inline_ref_size(inline_type) > end)) {
 			extent_err(leaf, slot,
 "inline ref item overflows extent item, ptr %lu iref size %u end %lu",
-				   ptr, inline_type, end);
+				   ptr, btrfs_extent_inline_ref_size(inline_type), end);
 			return -EUCLEAN;
 		}
 
@@ -1386,6 +1416,11 @@
 					   dref_offset, fs_info->sectorsize);
 				return -EUCLEAN;
 			}
+			if (unlikely(btrfs_extent_data_ref_count(leaf, dref) == 0)) {
+				extent_err(leaf, slot,
+			"invalid data ref count, should have non-zero value");
+				return -EUCLEAN;
+			}
 			inline_refs += btrfs_extent_data_ref_count(leaf, dref);
 			break;
 		/* Contains parent bytenr and ref count */
@@ -1398,6 +1433,11 @@
 					   inline_offset, fs_info->sectorsize);
 				return -EUCLEAN;
 			}
+			if (unlikely(btrfs_shared_data_ref_count(leaf, sref) == 0)) {
+				extent_err(leaf, slot,
+			"invalid shared data ref count, should have non-zero value");
+				return -EUCLEAN;
+			}
 			inline_refs += btrfs_shared_data_ref_count(leaf, sref);
 			break;
 		default:
@@ -1421,6 +1461,26 @@
 			   total_refs, inline_refs);
 		return -EUCLEAN;
 	}
+
+	if ((prev_key->type == BTRFS_EXTENT_ITEM_KEY) ||
+	    (prev_key->type == BTRFS_METADATA_ITEM_KEY)) {
+		u64 prev_end = prev_key->objectid;
+
+		if (prev_key->type == BTRFS_METADATA_ITEM_KEY)
+			prev_end += fs_info->nodesize;
+		else
+			prev_end += prev_key->offset;
+
+		if (unlikely(prev_end > key->objectid)) {
+			extent_err(leaf, slot,
+	"previous extent [%llu %u %llu] overlaps current extent [%llu %u %llu]",
+				   prev_key->objectid, prev_key->type,
+				   prev_key->offset, key->objectid, key->type,
+				   key->offset);
+			return -EUCLEAN;
+		}
+	}
+
 	return 0;
 }
 
@@ -1429,8 +1489,18 @@
 {
 	u32 expect_item_size = 0;
 
-	if (key->type == BTRFS_SHARED_DATA_REF_KEY)
+	if (key->type == BTRFS_SHARED_DATA_REF_KEY) {
+		struct btrfs_shared_data_ref *sref;
+
+		sref = btrfs_item_ptr(leaf, slot, struct btrfs_shared_data_ref);
+		if (unlikely(btrfs_shared_data_ref_count(leaf, sref) == 0)) {
+			extent_err(leaf, slot,
+		"invalid shared data backref count, should have non-zero value");
+			return -EUCLEAN;
+		}
+
 		expect_item_size = sizeof(struct btrfs_shared_data_ref);
+	}
 
 	if (unlikely(btrfs_item_size_nr(leaf, slot) != expect_item_size)) {
 		generic_err(leaf, slot,
@@ -1490,6 +1560,11 @@
 				   offset, leaf->fs_info->sectorsize);
 			return -EUCLEAN;
 		}
+		if (unlikely(btrfs_extent_data_ref_count(leaf, dref) == 0)) {
+			extent_err(leaf, slot,
+	"invalid extent data backref count, should have non-zero value");
+			return -EUCLEAN;
+		}
 	}
 	return 0;
 }
@@ -1546,6 +1621,72 @@
 	return 0;
 }
 
+static int check_dev_extent_item(const struct extent_buffer *leaf,
+				 const struct btrfs_key *key,
+				 int slot,
+				 struct btrfs_key *prev_key)
+{
+	struct btrfs_dev_extent *de;
+	const u32 sectorsize = leaf->fs_info->sectorsize;
+
+	de = btrfs_item_ptr(leaf, slot, struct btrfs_dev_extent);
+	/* Basic fixed member checks. */
+	if (unlikely(btrfs_dev_extent_chunk_tree(leaf, de) !=
+		     BTRFS_CHUNK_TREE_OBJECTID)) {
+		generic_err(leaf, slot,
+			    "invalid dev extent chunk tree id, has %llu expect %llu",
+			    btrfs_dev_extent_chunk_tree(leaf, de),
+			    BTRFS_CHUNK_TREE_OBJECTID);
+		return -EUCLEAN;
+	}
+	if (unlikely(btrfs_dev_extent_chunk_objectid(leaf, de) !=
+		     BTRFS_FIRST_CHUNK_TREE_OBJECTID)) {
+		generic_err(leaf, slot,
+			    "invalid dev extent chunk objectid, has %llu expect %llu",
+			    btrfs_dev_extent_chunk_objectid(leaf, de),
+			    BTRFS_FIRST_CHUNK_TREE_OBJECTID);
+		return -EUCLEAN;
+	}
+	/* Alignment check. */
+	if (unlikely(!IS_ALIGNED(key->offset, sectorsize))) {
+		generic_err(leaf, slot,
+			    "invalid dev extent key.offset, has %llu not aligned to %u",
+			    key->offset, sectorsize);
+		return -EUCLEAN;
+	}
+	if (unlikely(!IS_ALIGNED(btrfs_dev_extent_chunk_offset(leaf, de),
+				 sectorsize))) {
+		generic_err(leaf, slot,
+			    "invalid dev extent chunk offset, has %llu not aligned to %u",
+			    btrfs_dev_extent_chunk_objectid(leaf, de),
+			    sectorsize);
+		return -EUCLEAN;
+	}
+	if (unlikely(!IS_ALIGNED(btrfs_dev_extent_length(leaf, de),
+				 sectorsize))) {
+		generic_err(leaf, slot,
+			    "invalid dev extent length, has %llu not aligned to %u",
+			    btrfs_dev_extent_length(leaf, de), sectorsize);
+		return -EUCLEAN;
+	}
+	/* Overlap check with previous dev extent. */
+	if (slot && prev_key->objectid == key->objectid &&
+	    prev_key->type == key->type) {
+		struct btrfs_dev_extent *prev_de;
+		u64 prev_len;
+
+		prev_de = btrfs_item_ptr(leaf, slot - 1, struct btrfs_dev_extent);
+		prev_len = btrfs_dev_extent_length(leaf, prev_de);
+		if (unlikely(prev_key->offset + prev_len > key->offset)) {
+			generic_err(leaf, slot,
+		"dev extent overlap, prev offset %llu len %llu current offset %llu",
+				    prev_key->objectid, prev_len, key->offset);
+			return -EUCLEAN;
+		}
+	}
+	return 0;
+}
+
 /*
  * Common point to switch the item-specific validation.
  */
@@ -1581,6 +1722,9 @@
 	case BTRFS_DEV_ITEM_KEY:
 		ret = check_dev_item(leaf, key, slot);
 		break;
+	case BTRFS_DEV_EXTENT_KEY:
+		ret = check_dev_extent_item(leaf, key, slot, prev_key);
+		break;
 	case BTRFS_INODE_ITEM_KEY:
 		ret = check_inode_item(leaf, key, slot);
 		break;
@@ -1589,7 +1733,7 @@
 		break;
 	case BTRFS_EXTENT_ITEM_KEY:
 	case BTRFS_METADATA_ITEM_KEY:
-		ret = check_extent_item(leaf, key, slot);
+		ret = check_extent_item(leaf, key, slot, prev_key);
 		break;
 	case BTRFS_TREE_BLOCK_REF_KEY:
 	case BTRFS_SHARED_DATA_REF_KEY:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/tree-defrag.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/tree-defrag.c
@@ -39,8 +39,10 @@
 		goto out;
 
 	path = btrfs_alloc_path();
-	if (!path)
-		return -ENOMEM;
+	if (!path) {
+		ret = -ENOMEM;
+		goto out;
+	}
 
 	level = btrfs_header_level(root->node);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/tree-log.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/tree-log.c
@@ -761,7 +761,7 @@
 						ins.objectid, ins.offset, 0);
 				btrfs_init_data_ref(&ref,
 						root->root_key.objectid,
-						key->objectid, offset);
+						key->objectid, offset, 0, false);
 				ret = btrfs_inc_extent_ref(trans, &ref);
 				if (ret)
 					goto out;
@@ -884,6 +884,26 @@
 	return ret;
 }
 
+static int unlink_inode_for_log_replay(struct btrfs_trans_handle *trans,
+				       struct btrfs_inode *dir,
+				       struct btrfs_inode *inode,
+				       const char *name,
+				       int name_len)
+{
+	int ret;
+
+	ret = btrfs_unlink_inode(trans, dir, inode, name, name_len);
+	if (ret)
+		return ret;
+	/*
+	 * Whenever we need to check if a name exists or not, we check the
+	 * fs/subvolume tree. So after an unlink we must run delayed items, so
+	 * that future checks for a name during log replay see that the name
+	 * does not exists anymore.
+	 */
+	return btrfs_run_delayed_items(trans);
+}
+
 /*
  * when cleaning up conflicts between the directory names in the
  * subvolume, directory names in the log and directory names in the
@@ -926,12 +946,8 @@
 	if (ret)
 		goto out;
 
-	ret = btrfs_unlink_inode(trans, root, dir, BTRFS_I(inode), name,
+	ret = unlink_inode_for_log_replay(trans, dir, BTRFS_I(inode), name,
 			name_len);
-	if (ret)
-		goto out;
-	else
-		ret = btrfs_run_delayed_items(trans);
 out:
 	kfree(name);
 	iput(inode);
@@ -1091,14 +1107,11 @@
 				inc_nlink(&inode->vfs_inode);
 				btrfs_release_path(path);
 
-				ret = btrfs_unlink_inode(trans, root, dir, inode,
+				ret = unlink_inode_for_log_replay(trans, dir, inode,
 						victim_name, victim_name_len);
 				kfree(victim_name);
 				if (ret)
 					return ret;
-				ret = btrfs_run_delayed_items(trans);
-				if (ret)
-					return ret;
 				*search_done = 1;
 				goto again;
 			}
@@ -1119,7 +1132,9 @@
 	extref = btrfs_lookup_inode_extref(NULL, root, path, name, namelen,
 					   inode_objectid, parent_objectid, 0,
 					   0);
-	if (!IS_ERR_OR_NULL(extref)) {
+	if (IS_ERR(extref)) {
+		return PTR_ERR(extref);
+	} else if (extref) {
 		u32 item_size;
 		u32 cur_offset = 0;
 		unsigned long base;
@@ -1153,6 +1168,7 @@
 					     parent_objectid, victim_name,
 					     victim_name_len);
 			if (ret < 0) {
+				kfree(victim_name);
 				return ret;
 			} else if (!ret) {
 				ret = -ENOENT;
@@ -1162,14 +1178,11 @@
 					inc_nlink(&inode->vfs_inode);
 					btrfs_release_path(path);
 
-					ret = btrfs_unlink_inode(trans, root,
+					ret = unlink_inode_for_log_replay(trans,
 							BTRFS_I(victim_parent),
 							inode,
 							victim_name,
 							victim_name_len);
-					if (!ret)
-						ret = btrfs_run_delayed_items(
-								  trans);
 				}
 				iput(victim_parent);
 				kfree(victim_name);
@@ -1324,7 +1337,7 @@
 				kfree(name);
 				goto out;
 			}
-			ret = btrfs_unlink_inode(trans, root, BTRFS_I(dir),
+			ret = unlink_inode_for_log_replay(trans, BTRFS_I(dir),
 						 inode, name, namelen);
 			kfree(name);
 			iput(dir);
@@ -1422,8 +1435,8 @@
 		ret = -ENOENT;
 		goto out;
 	}
-	ret = btrfs_unlink_inode(trans, root, BTRFS_I(dir), BTRFS_I(other_inode),
-				 name, namelen);
+	ret = unlink_inode_for_log_replay(trans, BTRFS_I(dir), BTRFS_I(other_inode),
+					  name, namelen);
 	if (ret)
 		goto out;
 	/*
@@ -1431,11 +1444,7 @@
 	 * on the inode will not free it. We will fixup the link count later.
 	 */
 	if (other_inode->i_nlink == 0)
-		inc_nlink(other_inode);
-
-	ret = btrfs_run_delayed_items(trans);
-	if (ret)
-		goto out;
+		set_nlink(other_inode, 1);
 add_link:
 	ret = btrfs_add_link(trans, BTRFS_I(dir), BTRFS_I(inode),
 			     name, namelen, 0, ref_index);
@@ -1568,7 +1577,7 @@
 			ret = btrfs_inode_ref_exists(inode, dir, key->type,
 						     name, namelen);
 			if (ret > 0) {
-				ret = btrfs_unlink_inode(trans, root,
+				ret = unlink_inode_for_log_replay(trans,
 							 BTRFS_I(dir),
 							 BTRFS_I(inode),
 							 name, namelen);
@@ -1578,7 +1587,7 @@
 				 * free it. We will fixup the link count later.
 				 */
 				if (!ret && inode->i_nlink == 0)
-					inc_nlink(inode);
+					set_nlink(inode, 1);
 			}
 			if (ret < 0)
 				goto out;
@@ -2176,7 +2185,7 @@
  */
 static noinline int find_dir_range(struct btrfs_root *root,
 				   struct btrfs_path *path,
-				   u64 dirid, int key_type,
+				   u64 dirid,
 				   u64 *start_ret, u64 *end_ret)
 {
 	struct btrfs_key key;
@@ -2189,7 +2198,7 @@
 		return 1;
 
 	key.objectid = dirid;
-	key.type = key_type;
+	key.type = BTRFS_DIR_LOG_INDEX_KEY;
 	key.offset = *start_ret;
 
 	ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
@@ -2203,7 +2212,7 @@
 	if (ret != 0)
 		btrfs_item_key_to_cpu(path->nodes[0], &key, path->slots[0]);
 
-	if (key.type != key_type || key.objectid != dirid) {
+	if (key.type != BTRFS_DIR_LOG_INDEX_KEY || key.objectid != dirid) {
 		ret = 1;
 		goto next;
 	}
@@ -2230,7 +2239,7 @@
 
 	btrfs_item_key_to_cpu(path->nodes[0], &key, path->slots[0]);
 
-	if (key.type != key_type || key.objectid != dirid) {
+	if (key.type != BTRFS_DIR_LOG_INDEX_KEY || key.objectid != dirid) {
 		ret = 1;
 		goto out;
 	}
@@ -2261,95 +2270,75 @@
 	int ret;
 	struct extent_buffer *eb;
 	int slot;
-	u32 item_size;
 	struct btrfs_dir_item *di;
-	struct btrfs_dir_item *log_di;
 	int name_len;
-	unsigned long ptr;
-	unsigned long ptr_end;
 	char *name;
-	struct inode *inode;
+	struct inode *inode = NULL;
 	struct btrfs_key location;
 
-again:
+	/*
+	 * Currenly we only log dir index keys. Even if we replay a log created
+	 * by an older kernel that logged both dir index and dir item keys, all
+	 * we need to do is process the dir index keys, we (and our caller) can
+	 * safely ignore dir item keys (key type BTRFS_DIR_ITEM_KEY).
+	 */
+	ASSERT(dir_key->type == BTRFS_DIR_INDEX_KEY);
+
 	eb = path->nodes[0];
 	slot = path->slots[0];
-	item_size = btrfs_item_size_nr(eb, slot);
-	ptr = btrfs_item_ptr_offset(eb, slot);
-	ptr_end = ptr + item_size;
-	while (ptr < ptr_end) {
-		di = (struct btrfs_dir_item *)ptr;
-		name_len = btrfs_dir_name_len(eb, di);
-		name = kmalloc(name_len, GFP_NOFS);
-		if (!name) {
-			ret = -ENOMEM;
-			goto out;
-		}
-		read_extent_buffer(eb, name, (unsigned long)(di + 1),
-				  name_len);
-		log_di = NULL;
-		if (log && dir_key->type == BTRFS_DIR_ITEM_KEY) {
-			log_di = btrfs_lookup_dir_item(trans, log, log_path,
-						       dir_key->objectid,
-						       name, name_len, 0);
-		} else if (log && dir_key->type == BTRFS_DIR_INDEX_KEY) {
-			log_di = btrfs_lookup_dir_index_item(trans, log,
-						     log_path,
-						     dir_key->objectid,
-						     dir_key->offset,
-						     name, name_len, 0);
-		}
-		if (!log_di) {
-			btrfs_dir_item_key_to_cpu(eb, di, &location);
-			btrfs_release_path(path);
-			btrfs_release_path(log_path);
-			inode = read_one_inode(root, location.objectid);
-			if (!inode) {
-				kfree(name);
-				return -EIO;
-			}
+	di = btrfs_item_ptr(eb, slot, struct btrfs_dir_item);
+	name_len = btrfs_dir_name_len(eb, di);
+	name = kmalloc(name_len, GFP_NOFS);
+	if (!name) {
+		ret = -ENOMEM;
+		goto out;
+	}
 
-			ret = link_to_fixup_dir(trans, root,
-						path, location.objectid);
-			if (ret) {
-				kfree(name);
-				iput(inode);
-				goto out;
-			}
+	read_extent_buffer(eb, name, (unsigned long)(di + 1), name_len);
 
-			inc_nlink(inode);
-			ret = btrfs_unlink_inode(trans, root, BTRFS_I(dir),
-					BTRFS_I(inode), name, name_len);
-			if (!ret)
-				ret = btrfs_run_delayed_items(trans);
-			kfree(name);
-			iput(inode);
-			if (ret)
-				goto out;
+	if (log) {
+		struct btrfs_dir_item *log_di;
 
-			/* there might still be more names under this key
-			 * check and repeat if required
-			 */
-			ret = btrfs_search_slot(NULL, root, dir_key, path,
-						0, 0);
-			if (ret == 0)
-				goto again;
+		log_di = btrfs_lookup_dir_index_item(trans, log, log_path,
+						     dir_key->objectid,
+						     dir_key->offset,
+						     name, name_len, 0);
+		if (IS_ERR(log_di)) {
+			ret = PTR_ERR(log_di);
+			goto out;
+		} else if (log_di) {
+			/* The dentry exists in the log, we have nothing to do. */
 			ret = 0;
 			goto out;
-		} else if (IS_ERR(log_di)) {
-			kfree(name);
-			return PTR_ERR(log_di);
 		}
-		btrfs_release_path(log_path);
-		kfree(name);
+	}
 
-		ptr = (unsigned long)(di + 1);
-		ptr += name_len;
+	btrfs_dir_item_key_to_cpu(eb, di, &location);
+	btrfs_release_path(path);
+	btrfs_release_path(log_path);
+	inode = read_one_inode(root, location.objectid);
+	if (!inode) {
+		ret = -EIO;
+		goto out;
 	}
-	ret = 0;
+
+	ret = link_to_fixup_dir(trans, root, path, location.objectid);
+	if (ret)
+		goto out;
+
+	inc_nlink(inode);
+	ret = unlink_inode_for_log_replay(trans, BTRFS_I(dir), BTRFS_I(inode),
+					  name, name_len);
+	/*
+	 * Unlike dir item keys, dir index keys can only have one name (entry) in
+	 * them, as there are no key collisions since each key has a unique offset
+	 * (an index number), so we're done.
+	 */
 out:
 	btrfs_release_path(path);
 	btrfs_release_path(log_path);
+	kfree(name);
+	iput(inode);
 	return ret;
 }
 
@@ -2469,7 +2458,6 @@
 {
 	u64 range_start;
 	u64 range_end;
-	int key_type = BTRFS_DIR_LOG_ITEM_KEY;
 	int ret = 0;
 	struct btrfs_key dir_key;
 	struct btrfs_key found_key;
@@ -2477,7 +2465,7 @@
 	struct inode *dir;
 
 	dir_key.objectid = dirid;
-	dir_key.type = BTRFS_DIR_ITEM_KEY;
+	dir_key.type = BTRFS_DIR_INDEX_KEY;
 	log_path = btrfs_alloc_path();
 	if (!log_path)
 		return -ENOMEM;
@@ -2491,16 +2479,18 @@
 		btrfs_free_path(log_path);
 		return 0;
 	}
-again:
+
 	range_start = 0;
 	range_end = 0;
 	while (1) {
 		if (del_all)
 			range_end = (u64)-1;
 		else {
-			ret = find_dir_range(log, path, dirid, key_type,
+			ret = find_dir_range(log, path, dirid,
 					     &range_start, &range_end);
-			if (ret != 0)
+			if (ret < 0)
+				goto out;
+			else if (ret > 0)
 				break;
 		}
 
@@ -2523,8 +2513,10 @@
 			btrfs_item_key_to_cpu(path->nodes[0], &found_key,
 					      path->slots[0]);
 			if (found_key.objectid != dirid ||
-			    found_key.type != dir_key.type)
-				goto next_type;
+			    found_key.type != dir_key.type) {
+				ret = 0;
+				goto out;
+			}
 
 			if (found_key.offset > range_end)
 				break;
@@ -2543,15 +2535,7 @@
 			break;
 		range_start = range_end + 1;
 	}
-
-next_type:
 	ret = 0;
-	if (key_type == BTRFS_DIR_LOG_ITEM_KEY) {
-		key_type = BTRFS_DIR_LOG_INDEX_KEY;
-		dir_key.type = BTRFS_DIR_INDEX_KEY;
-		btrfs_release_path(path);
-		goto again;
-	}
 out:
 	btrfs_release_path(path);
 	btrfs_free_path(log_path);
@@ -2877,6 +2861,8 @@
 						     path->nodes[*level]->len);
 					if (ret)
 						return ret;
+					btrfs_redirty_list_add(trans->transaction,
+							       next);
 				} else {
 					if (test_and_clear_bit(EXTENT_BUFFER_DIRTY, &next->bflags))
 						clear_extent_buffer_dirty(next);
@@ -2957,6 +2943,7 @@
 						next->start, next->len);
 				if (ret)
 					goto out;
+				btrfs_redirty_list_add(trans->transaction, next);
 			} else {
 				if (test_and_clear_bit(EXTENT_BUFFER_DIRTY, &next->bflags))
 					clear_extent_buffer_dirty(next);
@@ -3154,7 +3141,6 @@
 		ret = 0;
 	if (ret) {
 		blk_finish_plug(&plug);
-		btrfs_abort_transaction(trans, ret);
 		btrfs_set_log_full_commit(trans);
 		mutex_unlock(&root->log_mutex);
 		goto out;
@@ -3192,6 +3178,7 @@
 			ret = btrfs_alloc_log_tree_node(trans, log_root_tree);
 			if (ret) {
 				mutex_unlock(&fs_info->tree_root->log_mutex);
+				blk_finish_plug(&plug);
 				goto out;
 			}
 		}
@@ -3285,7 +3272,6 @@
 		goto out_wake_log_root;
 	} else if (ret) {
 		btrfs_set_log_full_commit(trans);
-		btrfs_abort_transaction(trans, ret);
 		mutex_unlock(&log_root_tree->log_mutex);
 		goto out_wake_log_root;
 	}
@@ -3399,6 +3385,29 @@
 	if (log->node) {
 		ret = walk_log_tree(trans, log, &wc);
 		if (ret) {
+			/*
+			 * We weren't able to traverse the entire log tree, the
+			 * typical scenario is getting an -EIO when reading an
+			 * extent buffer of the tree, due to a previous writeback
+			 * failure of it.
+			 */
+			set_bit(BTRFS_FS_STATE_LOG_CLEANUP_ERROR,
+				&log->fs_info->fs_state);
+
+			/*
+			 * Some extent buffers of the log tree may still be dirty
+			 * and not yet written back to storage, because we may
+			 * have updates to a log tree without syncing a log tree,
+			 * such as during rename and link operations. So flush
+			 * them out and wait for their writeback to complete, so
+			 * that we properly cleanup their state and pages.
+			 */
+			btrfs_write_marked_extents(log->fs_info,
+						   &log->dirty_log_pages,
+						   EXTENT_DIRTY | EXTENT_NEW);
+			btrfs_wait_tree_log_extents(log,
+						    EXTENT_DIRTY | EXTENT_NEW);
+
 			if (trans)
 				btrfs_abort_transaction(trans, ret);
 			else
@@ -3410,8 +3419,6 @@
 			  EXTENT_DIRTY | EXTENT_NEW | EXTENT_NEED_WAIT);
 	extent_io_tree_release(&log->log_csum_range);
 
-	if (trans && log->node)
-		btrfs_redirty_list_add(trans->transaction, log->node);
 	btrfs_put_root(log);
 }
 
@@ -4419,7 +4426,7 @@
 
 /*
  * Log all prealloc extents beyond the inode's i_size to make sure we do not
- * lose them after doing a fast fsync and replaying the log. We scan the
+ * lose them after doing a full/fast fsync and replaying the log. We scan the
  * subvolume's root instead of iterating the inode's extent map tree because
  * otherwise we can log incorrect extent items based on extent map conversion.
  * That can happen due to the fact that extent maps are merged when they
@@ -4439,7 +4446,7 @@
 	struct extent_buffer *leaf;
 	int slot;
 	int ins_nr = 0;
-	int start_slot;
+	int start_slot = 0;
 	int ret;
 
 	if (!(inode->flags & BTRFS_INODE_PREALLOC))
@@ -5204,6 +5211,7 @@
 				   struct btrfs_log_ctx *ctx,
 				   bool *need_log_inode_item)
 {
+	const u64 i_size = i_size_read(&inode->vfs_inode);
 	struct btrfs_root *root = inode->root;
 	int ins_start_slot = 0;
 	int ins_nr = 0;
@@ -5224,13 +5232,21 @@
 		if (min_key->type > max_key->type)
 			break;
 
-		if (min_key->type == BTRFS_INODE_ITEM_KEY)
+		if (min_key->type == BTRFS_INODE_ITEM_KEY) {
 			*need_log_inode_item = false;
-
-		if ((min_key->type == BTRFS_INODE_REF_KEY ||
-		     min_key->type == BTRFS_INODE_EXTREF_KEY) &&
-		    inode->generation == trans->transid &&
-		    !recursive_logging) {
+		} else if (min_key->type == BTRFS_EXTENT_DATA_KEY &&
+			   min_key->offset >= i_size) {
+			/*
+			 * Extents at and beyond eof are logged with
+			 * btrfs_log_prealloc_extents().
+			 * Only regular files have BTRFS_EXTENT_DATA_KEY keys,
+			 * and no keys greater than that, so bail out.
+			 */
+			break;
+		} else if ((min_key->type == BTRFS_INODE_REF_KEY ||
+			    min_key->type == BTRFS_INODE_EXTREF_KEY) &&
+			   inode->generation == trans->transid &&
+			   !recursive_logging) {
 			u64 other_ino = 0;
 			u64 other_parent = 0;
 
@@ -5261,10 +5277,8 @@
 				btrfs_release_path(path);
 				goto next_key;
 			}
-		}
-
-		/* Skip xattrs, we log them later with btrfs_log_all_xattrs() */
-		if (min_key->type == BTRFS_XATTR_ITEM_KEY) {
+		} else if (min_key->type == BTRFS_XATTR_ITEM_KEY) {
+			/* Skip xattrs, logged later with btrfs_log_all_xattrs() */
 			if (ins_nr == 0)
 				goto next_slot;
 			ret = copy_items(trans, inode, dst_path, path,
@@ -5317,9 +5331,21 @@
 			break;
 		}
 	}
-	if (ins_nr)
+	if (ins_nr) {
 		ret = copy_items(trans, inode, dst_path, path, ins_start_slot,
 				 ins_nr, inode_only, logged_isize);
+		if (ret)
+			return ret;
+	}
+
+	if (inode_only == LOG_INODE_ALL && S_ISREG(inode->vfs_inode.i_mode)) {
+		/*
+		 * Release the path because otherwise we might attempt to double
+		 * lock the same leaf with btrfs_log_prealloc_extents() below.
+		 */
+		btrfs_release_path(path);
+		ret = btrfs_log_prealloc_extents(trans, inode, dst_path);
+	}
 
 	return ret;
 }
@@ -5419,6 +5445,18 @@
 	}
 
 	/*
+	 * For symlinks, we must always log their content, which is stored in an
+	 * inline extent, otherwise we could end up with an empty symlink after
+	 * log replay, which is invalid on linux (symlink(2) returns -ENOENT if
+	 * one attempts to create an empty symlink).
+	 * We don't need to worry about flushing delalloc, because when we create
+	 * the inline extent when the symlink is created (we never have delalloc
+	 * for symlinks).
+	 */
+	if (S_ISLNK(inode->vfs_inode.i_mode))
+		inode_only = LOG_INODE_ALL;
+
+	/*
 	 * This is for cases where logging a directory could result in losing a
 	 * a file after replaying the log. For example, if we move a file from a
 	 * directory A to a directory B, then fsync directory A, we have no way
@@ -5788,7 +5826,7 @@
 			}
 
 			ctx->log_new_dentries = false;
-			if (type == BTRFS_FT_DIR || type == BTRFS_FT_SYMLINK)
+			if (type == BTRFS_FT_DIR)
 				log_mode = LOG_INODE_ALL;
 			ret = btrfs_log_inode(trans, root, BTRFS_I(di_inode),
 					      log_mode, ctx);
@@ -6549,14 +6587,25 @@
 	mutex_unlock(&dir->log_mutex);
 }
 
-/*
- * Call this after adding a new name for a file and it will properly
- * update the log to reflect the new name.
+/**
+ * Update the log after adding a new name for an inode.
+ *
+ * @trans:              Transaction handle.
+ * @old_dentry:         The dentry associated with the old name and the old
+ *                      parent directory.
+ * @old_dir:            The inode of the previous parent directory for the case
+ *                      of a rename. For a link operation, it must be NULL.
+ * @parent:             The dentry associated with the directory under which the
+ *                      new name is located.
+ *
+ * Call this after adding a new name for an inode, as a result of a link or
+ * rename operation, and it will properly update the log to reflect the new name.
  */
 void btrfs_log_new_name(struct btrfs_trans_handle *trans,
-			struct btrfs_inode *inode, struct btrfs_inode *old_dir,
+			struct dentry *old_dentry, struct btrfs_inode *old_dir,
 			struct dentry *parent)
 {
+	struct btrfs_inode *inode = BTRFS_I(d_inode(old_dentry));
 	struct btrfs_log_ctx ctx;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/tree-log.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/tree-log.h
@@ -84,7 +84,7 @@
 void btrfs_record_snapshot_destroy(struct btrfs_trans_handle *trans,
 				   struct btrfs_inode *dir);
 void btrfs_log_new_name(struct btrfs_trans_handle *trans,
-			struct btrfs_inode *inode, struct btrfs_inode *old_dir,
+			struct dentry *old_dentry, struct btrfs_inode *old_dir,
 			struct dentry *parent);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/volumes.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/volumes.c
@@ -14,6 +14,7 @@
 #include <linux/semaphore.h>
 #include <linux/uuid.h>
 #include <linux/list_sort.h>
+#include <linux/namei.h>
 #include "misc.h"
 #include "ctree.h"
 #include "extent_map.h"
@@ -250,7 +251,7 @@
 static int __btrfs_map_block(struct btrfs_fs_info *fs_info,
 			     enum btrfs_map_op op,
 			     u64 logical, u64 *length,
-			     struct btrfs_bio **bbio_ret,
+			     struct btrfs_io_context **bioc_ret,
 			     int mirror_num, int need_raid_map);
 
 /*
@@ -408,6 +409,7 @@
 static void free_fs_devices(struct btrfs_fs_devices *fs_devices)
 {
 	struct btrfs_device *device;
+
 	WARN_ON(fs_devices->opened);
 	while (!list_empty(&fs_devices->devices)) {
 		device = list_entry(fs_devices->devices.next,
@@ -529,15 +531,48 @@
 	return ret;
 }
 
-static bool device_path_matched(const char *path, struct btrfs_device *device)
+/*
+ * Check if the device in the path matches the device in the given struct device.
+ *
+ * Returns:
+ *   true  If it is the same device.
+ *   false If it is not the same device or on error.
+ */
+static bool device_matched(const struct btrfs_device *device, const char *path)
 {
-	int found;
+	char *device_name;
+	dev_t dev_old;
+	dev_t dev_new;
+	int ret;
+
+	/*
+	 * If we are looking for a device with the matching dev_t, then skip
+	 * device without a name (a missing device).
+	 */
+	if (!device->name)
+		return false;
+
+	device_name = kzalloc(BTRFS_PATH_NAME_MAX, GFP_KERNEL);
+	if (!device_name)
+		return false;
 
 	rcu_read_lock();
-	found = strcmp(rcu_str_deref(device->name), path);
+	scnprintf(device_name, BTRFS_PATH_NAME_MAX, "%s", rcu_str_deref(device->name));
 	rcu_read_unlock();
 
-	return found == 0;
+	ret = lookup_bdev(device_name, &dev_old);
+	kfree(device_name);
+	if (ret)
+		return false;
+
+	ret = lookup_bdev(path, &dev_new);
+	if (ret)
+		return false;
+
+	if (dev_old == dev_new)
+		return true;
+
+	return false;
 }
 
 /*
@@ -570,9 +605,7 @@
 					 &fs_devices->devices, dev_list) {
 			if (skip_device && skip_device == device)
 				continue;
-			if (path && !device->name)
-				continue;
-			if (path && !device_path_matched(path, device))
+			if (path && !device_matched(device, path))
 				continue;
 			if (fs_devices->opened) {
 				/* for an already deleted device return 0 */
@@ -676,6 +709,50 @@
 	return -EINVAL;
 }
 
+u8 *btrfs_sb_fsid_ptr(struct btrfs_super_block *sb)
+{
+	bool has_metadata_uuid = (btrfs_super_incompat_flags(sb) &
+				  BTRFS_FEATURE_INCOMPAT_METADATA_UUID);
+
+	return has_metadata_uuid ? sb->metadata_uuid : sb->fsid;
+}
+
+static bool is_same_device(struct btrfs_device *device, const char *new_path)
+{
+	struct path old = { .mnt = NULL, .dentry = NULL };
+	struct path new = { .mnt = NULL, .dentry = NULL };
+	char *old_path = NULL;
+	bool is_same = false;
+	int ret;
+
+	if (!device->name)
+		goto out;
+
+	old_path = kzalloc(PATH_MAX, GFP_NOFS);
+	if (!old_path)
+		goto out;
+
+	rcu_read_lock();
+	ret = strscpy(old_path, rcu_str_deref(device->name), PATH_MAX);
+	rcu_read_unlock();
+	if (ret < 0)
+		goto out;
+
+	ret = kern_path(old_path, LOOKUP_FOLLOW, &old);
+	if (ret)
+		goto out;
+	ret = kern_path(new_path, LOOKUP_FOLLOW, &new);
+	if (ret)
+		goto out;
+	if (path_equal(&old, &new))
+		is_same = true;
+out:
+	kfree(old_path);
+	path_put(&old);
+	path_put(&new);
+	return is_same;
+}
+
 /*
  * Handle scanned device having its CHANGING_FSID_V2 flag set and the fs_devices
  * being created with a disk that has already completed its fsid change. Such
@@ -812,9 +889,13 @@
 
 		device = NULL;
 	} else {
+		struct btrfs_dev_lookup_args args = {
+			.devid = devid,
+			.uuid = disk_super->dev_item.uuid,
+		};
+
 		mutex_lock(&fs_devices->device_list_mutex);
-		device = btrfs_find_device(fs_devices, devid,
-				disk_super->dev_item.uuid, NULL);
+		device = btrfs_find_device(fs_devices, &args);
 
 		/*
 		 * If this disk has been pulled into an fs devices created by
@@ -877,7 +958,7 @@
 				disk_super->fsid, devid, found_transid, path,
 				current->comm, task_pid_nr(current));
 
-	} else if (!device->name || strcmp(device->name->str, path)) {
+	} else if (!device->name || !is_same_device(device, path)) {
 		/*
 		 * When FS is already mounted.
 		 * 1. If you are here and if the device->name is NULL that
@@ -919,6 +1000,11 @@
 		/*
 		 * We are going to replace the device path for a given devid,
 		 * make sure it's the same device if the device is mounted
+		 *
+		 * NOTE: the device->fs_info may not be reliable here so pass
+		 * in a NULL to message helpers instead. This avoids a possible
+		 * use-after-free when the fs_info and fs_info->sb are already
+		 * torn down.
 		 */
 		if (device->bdev) {
 			int error;
@@ -932,12 +1018,6 @@
 
 			if (device->bdev->bd_dev != path_dev) {
 				mutex_unlock(&fs_devices->device_list_mutex);
-				/*
-				 * device->fs_info may not be reliable here, so
-				 * pass in a NULL instead. This avoids a
-				 * possible use-after-free when the fs_info and
-				 * fs_info->sb are already torn down.
-				 */
 				btrfs_warn_in_rcu(NULL,
 	"duplicate device %s devid %llu generation %llu scanned by %s (%d)",
 						  path, devid, found_transid,
@@ -945,7 +1025,7 @@
 						  task_pid_nr(current));
 				return ERR_PTR(-EEXIST);
 			}
-			btrfs_info_in_rcu(device->fs_info,
+			btrfs_info_in_rcu(NULL,
 	"devid %llu device path %s changed to %s scanned by %s (%d)",
 					  devid, rcu_str_deref(device->name),
 					  path, current->comm,
@@ -1091,7 +1171,7 @@
 	list_for_each_entry(seed_dev, &fs_devices->seed_list, seed_list)
 		__btrfs_free_extra_devids(seed_dev, &latest_dev);
 
-	fs_devices->latest_bdev = latest_dev->bdev;
+	fs_devices->latest_dev = latest_dev;
 
 	mutex_unlock(&uuid_mutex);
 }
@@ -1122,8 +1202,10 @@
 	if (device->devid == BTRFS_DEV_REPLACE_DEVID)
 		clear_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state);
 
-	if (test_bit(BTRFS_DEV_STATE_MISSING, &device->dev_state))
+	if (test_bit(BTRFS_DEV_STATE_MISSING, &device->dev_state)) {
+		clear_bit(BTRFS_DEV_STATE_MISSING, &device->dev_state);
 		fs_devices->missing_devices--;
+	}
 
 	btrfs_close_bdev(device);
 	if (device->bdev) {
@@ -1184,9 +1266,22 @@
 
 	mutex_lock(&uuid_mutex);
 	close_fs_devices(fs_devices);
-	if (!fs_devices->opened)
+	if (!fs_devices->opened) {
 		list_splice_init(&fs_devices->seed_list, &list);
 
+		/*
+		 * If the struct btrfs_fs_devices is not assembled with any
+		 * other device, it can be re-initialized during the next mount
+		 * without the needing device-scan step. Therefore, it can be
+		 * fully freed.
+		 */
+		if (fs_devices->num_devices == 1) {
+			list_del(&fs_devices->fs_list);
+			free_fs_devices(fs_devices);
+		}
+	}
+
+
 	list_for_each_entry_safe(fs_devices, tmp, &list, seed_list) {
 		close_fs_devices(fs_devices);
 		list_del(&fs_devices->seed_list);
@@ -1201,28 +1296,35 @@
 	struct btrfs_device *device;
 	struct btrfs_device *latest_dev = NULL;
 	struct btrfs_device *tmp_device;
+	int ret = 0;
 
 	flags |= FMODE_EXCL;
 
 	list_for_each_entry_safe(device, tmp_device, &fs_devices->devices,
 				 dev_list) {
-		int ret;
+		int ret2;
 
-		ret = btrfs_open_one_device(fs_devices, device, flags, holder);
-		if (ret == 0 &&
+		ret2 = btrfs_open_one_device(fs_devices, device, flags, holder);
+		if (ret2 == 0 &&
 		    (!latest_dev || device->generation > latest_dev->generation)) {
 			latest_dev = device;
-		} else if (ret == -ENODATA) {
+		} else if (ret2 == -ENODATA) {
 			fs_devices->num_devices--;
 			list_del(&device->dev_list);
 			btrfs_free_device(device);
 		}
+		if (ret == 0 && ret2 != 0)
+			ret = ret2;
 	}
-	if (fs_devices->open_devices == 0)
+
+	if (fs_devices->open_devices == 0) {
+		if (ret)
+			return ret;
 		return -EINVAL;
+	}
 
 	fs_devices->opened = 1;
-	fs_devices->latest_bdev = latest_dev->bdev;
+	fs_devices->latest_dev = latest_dev;
 	fs_devices->total_rw_bytes = 0;
 	fs_devices->chunk_alloc_policy = BTRFS_CHUNK_ALLOC_REGULAR;
 	fs_devices->read_policy = BTRFS_READ_POLICY_PID;
@@ -1355,16 +1457,27 @@
 	 * So, we need to add a special mount option to scan for
 	 * later supers, using BTRFS_SUPER_MIRROR_MAX instead
 	 */
-	flags |= FMODE_EXCL;
 
+	/*
+	 * Avoid using flag |= FMODE_EXCL here, as the systemd-udev may
+	 * initiate the device scan which may race with the user's mount
+	 * or mkfs command, resulting in failure.
+	 * Since the device scan is solely for reading purposes, there is
+	 * no need for FMODE_EXCL. Additionally, the devices are read again
+	 * during the mount process. It is ok to get some inconsistent
+	 * values temporarily, as the device paths of the fsid are the only
+	 * required information for assembling the volume.
+	 */
 	bdev = blkdev_get_by_path(path, flags, holder);
 	if (IS_ERR(bdev))
 		return ERR_CAST(bdev);
 
 	bytenr_orig = btrfs_sb_offset(0);
 	ret = btrfs_sb_log_location_bdev(bdev, 0, READ, &bytenr);
-	if (ret)
-		return ERR_PTR(ret);
+	if (ret) {
+		device = ERR_PTR(ret);
+		goto error_bdev_put;
+	}
 
 	disk_super = btrfs_read_disk_super(bdev, bytenr, bytenr_orig);
 	if (IS_ERR(disk_super)) {
@@ -1403,7 +1516,7 @@
 
 		if (in_range(physical_start, *start, len) ||
 		    in_range(*start, physical_start,
-			     physical_end - physical_start)) {
+			     physical_end + 1 - physical_start)) {
 			*start = physical_end + 1;
 			return true;
 		}
@@ -1607,7 +1720,7 @@
 	if (ret < 0)
 		goto out;
 
-	while (1) {
+	while (search_start < search_end) {
 		l = path->nodes[0];
 		slot = path->slots[0];
 		if (slot >= btrfs_header_nritems(l)) {
@@ -1630,6 +1743,9 @@
 		if (key.type != BTRFS_DEV_EXTENT_KEY)
 			goto next;
 
+		if (key.offset > search_end)
+			break;
+
 		if (key.offset > search_start) {
 			hole_size = key.offset - search_start;
 			dev_extent_hole_check(device, &search_start, &hole_size,
@@ -1690,6 +1806,7 @@
 	else
 		ret = 0;
 
+	ASSERT(max_hole_start + max_hole_size <= search_end);
 out:
 	btrfs_free_path(path);
 	*start = max_hole_start;
@@ -1843,8 +1960,10 @@
 	key.type = BTRFS_DEV_ITEM_KEY;
 	key.offset = device->devid;
 
+	btrfs_reserve_chunk_metadata(trans, true);
 	ret = btrfs_insert_empty_item(trans, trans->fs_info->chunk_root, path,
 				      &key, sizeof(*dev_item));
+	btrfs_trans_release_chunk_metadata(trans);
 	if (ret)
 		goto out;
 
@@ -1882,60 +2001,52 @@
 /*
  * Function to update ctime/mtime for a given device path.
  * Mainly used for ctime/mtime based probe like libblkid.
+ *
+ * We don't care about errors here, this is just to be kind to userspace.
  */
-static void update_dev_time(struct block_device *bdev)
+static void update_dev_time(const char *device_path)
 {
-	struct inode *inode = bdev->bd_inode;
+	struct path path;
 	struct timespec64 now;
+	int ret;
 
-	/* Shouldn't happen but just in case. */
-	if (!inode)
+	ret = kern_path(device_path, LOOKUP_FOLLOW, &path);
+	if (ret)
 		return;
 
-	now = current_time(inode);
-	generic_update_time(inode, &now, S_MTIME | S_CTIME);
+	now = current_time(d_inode(path.dentry));
+	inode_update_time(d_inode(path.dentry), &now, S_MTIME | S_CTIME);
+	path_put(&path);
 }
 
-static int btrfs_rm_dev_item(struct btrfs_device *device)
+static int btrfs_rm_dev_item(struct btrfs_trans_handle *trans,
+			     struct btrfs_device *device)
 {
 	struct btrfs_root *root = device->fs_info->chunk_root;
 	int ret;
 	struct btrfs_path *path;
 	struct btrfs_key key;
-	struct btrfs_trans_handle *trans;
 
 	path = btrfs_alloc_path();
 	if (!path)
 		return -ENOMEM;
 
-	trans = btrfs_start_transaction(root, 0);
-	if (IS_ERR(trans)) {
-		btrfs_free_path(path);
-		return PTR_ERR(trans);
-	}
 	key.objectid = BTRFS_DEV_ITEMS_OBJECTID;
 	key.type = BTRFS_DEV_ITEM_KEY;
 	key.offset = device->devid;
 
+	btrfs_reserve_chunk_metadata(trans, false);
 	ret = btrfs_search_slot(trans, root, &key, path, -1, 1);
+	btrfs_trans_release_chunk_metadata(trans);
 	if (ret) {
 		if (ret > 0)
 			ret = -ENOENT;
-		btrfs_abort_transaction(trans, ret);
-		btrfs_end_transaction(trans);
 		goto out;
 	}
 
 	ret = btrfs_del_item(trans, root, path);
-	if (ret) {
-		btrfs_abort_transaction(trans, ret);
-		btrfs_end_transaction(trans);
-	}
-
 out:
 	btrfs_free_path(path);
-	if (!ret)
-		ret = btrfs_commit_transaction(trans);
 	return ret;
 }
 
@@ -1986,7 +2097,7 @@
 }
 
 /*
- * Helper function to check if the given device is part of s_bdev / latest_bdev
+ * Helper function to check if the given device is part of s_bdev / latest_dev
  * and replace it with the provided or the next active device, in the context
  * where this function called, there should be always be another device (or
  * this_dev) which is active.
@@ -2005,8 +2116,8 @@
 			(fs_info->sb->s_bdev == device->bdev))
 		fs_info->sb->s_bdev = next_device->bdev;
 
-	if (fs_info->fs_devices->latest_bdev == device->bdev)
-		fs_info->fs_devices->latest_bdev = next_device->bdev;
+	if (fs_info->fs_devices->latest_dev->bdev == device->bdev)
+		fs_info->fs_devices->latest_dev = next_device;
 }
 
 /*
@@ -2041,7 +2152,7 @@
 		struct page *page;
 		int ret;
 
-		disk_super = btrfs_read_dev_one_super(bdev, copy_num);
+		disk_super = btrfs_read_dev_one_super(bdev, copy_num, false);
 		if (IS_ERR(disk_super))
 			continue;
 
@@ -2069,55 +2180,53 @@
 	btrfs_kobject_uevent(bdev, KOBJ_CHANGE);
 
 	/* Update ctime/mtime for device path for libblkid */
-	update_dev_time(bdev);
+	update_dev_time(device_path);
 }
 
-int btrfs_rm_device(struct btrfs_fs_info *fs_info, const char *device_path,
-		    u64 devid, struct block_device **bdev, fmode_t *mode)
+int btrfs_rm_device(struct btrfs_fs_info *fs_info,
+		    struct btrfs_dev_lookup_args *args,
+		    struct block_device **bdev, fmode_t *mode)
 {
+	struct btrfs_trans_handle *trans;
 	struct btrfs_device *device;
 	struct btrfs_fs_devices *cur_devices;
 	struct btrfs_fs_devices *fs_devices = fs_info->fs_devices;
 	u64 num_devices;
 	int ret = 0;
 
-	mutex_lock(&uuid_mutex);
-
+	/*
+	 * The device list in fs_devices is accessed without locks (neither
+	 * uuid_mutex nor device_list_mutex) as it won't change on a mounted
+	 * filesystem and another device rm cannot run.
+	 */
 	num_devices = btrfs_num_devices(fs_info);
 
 	ret = btrfs_check_raid_min_devices(fs_info, num_devices - 1);
 	if (ret)
-		goto out;
-
-	device = btrfs_find_device_by_devspec(fs_info, devid, device_path);
+		return ret;
 
-	if (IS_ERR(device)) {
-		if (PTR_ERR(device) == -ENOENT &&
-		    device_path && strcmp(device_path, "missing") == 0)
+	device = btrfs_find_device(fs_info->fs_devices, args);
+	if (!device) {
+		if (args->missing)
 			ret = BTRFS_ERROR_DEV_MISSING_NOT_FOUND;
 		else
-			ret = PTR_ERR(device);
-		goto out;
+			ret = -ENOENT;
+		return ret;
 	}
 
 	if (btrfs_pinned_by_swapfile(fs_info, device)) {
 		btrfs_warn_in_rcu(fs_info,
 		  "cannot remove device %s (devid %llu) due to active swapfile",
 				  rcu_str_deref(device->name), device->devid);
-		ret = -ETXTBSY;
-		goto out;
+		return -ETXTBSY;
 	}
 
-	if (test_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state)) {
-		ret = BTRFS_ERROR_DEV_TGT_REPLACE;
-		goto out;
-	}
+	if (test_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state))
+		return BTRFS_ERROR_DEV_TGT_REPLACE;
 
 	if (test_bit(BTRFS_DEV_STATE_WRITEABLE, &device->dev_state) &&
-	    fs_info->fs_devices->rw_devices == 1) {
-		ret = BTRFS_ERROR_DEV_ONLY_WRITABLE;
-		goto out;
-	}
+	    fs_info->fs_devices->rw_devices == 1)
+		return BTRFS_ERROR_DEV_ONLY_WRITABLE;
 
 	if (test_bit(BTRFS_DEV_STATE_WRITEABLE, &device->dev_state)) {
 		mutex_lock(&fs_info->chunk_mutex);
@@ -2126,22 +2235,28 @@
 		mutex_unlock(&fs_info->chunk_mutex);
 	}
 
-	mutex_unlock(&uuid_mutex);
 	ret = btrfs_shrink_device(device, 0);
 	if (!ret)
 		btrfs_reada_remove_dev(device);
-	mutex_lock(&uuid_mutex);
 	if (ret)
 		goto error_undo;
 
-	/*
-	 * TODO: the superblock still includes this device in its num_devices
-	 * counter although write_all_supers() is not locked out. This
-	 * could give a filesystem state which requires a degraded mount.
-	 */
-	ret = btrfs_rm_dev_item(device);
-	if (ret)
+	trans = btrfs_start_transaction(fs_info->chunk_root, 0);
+	if (IS_ERR(trans)) {
+		ret = PTR_ERR(trans);
 		goto error_undo;
+	}
+
+	ret = btrfs_rm_dev_item(trans, device);
+	if (ret) {
+		/* Any error in dev item removal is critical */
+		btrfs_crit(fs_info,
+			   "failed to remove device item for devid %llu: %d",
+			   device->devid, ret);
+		btrfs_abort_transaction(trans, ret);
+		btrfs_end_transaction(trans);
+		return ret;
+	}
 
 	clear_bit(BTRFS_DEV_STATE_IN_FS_METADATA, &device->dev_state);
 	btrfs_scrub_cancel_dev(device);
@@ -2216,8 +2331,8 @@
 		free_fs_devices(cur_devices);
 	}
 
-out:
-	mutex_unlock(&uuid_mutex);
+	ret = btrfs_commit_transaction(trans);
+
 	return ret;
 
 error_undo:
@@ -2229,7 +2344,7 @@
 		device->fs_devices->rw_devices++;
 		mutex_unlock(&fs_info->chunk_mutex);
 	}
-	goto out;
+	return ret;
 }
 
 void btrfs_rm_dev_replace_remove_srcdev(struct btrfs_device *srcdev)
@@ -2305,13 +2420,6 @@
 
 	mutex_unlock(&fs_devices->device_list_mutex);
 
-	/*
-	 * The update_dev_time() with in btrfs_scratch_superblocks()
-	 * may lead to a call to btrfs_show_devname() which will try
-	 * to hold device_list_mutex. And here this device
-	 * is already out of device list, so we don't have to hold
-	 * the device_list_mutex lock.
-	 */
 	btrfs_scratch_superblocks(tgtdev->fs_info, tgtdev->bdev,
 				  tgtdev->name->str);
 
@@ -2320,69 +2428,101 @@
 	btrfs_free_device(tgtdev);
 }
 
-static struct btrfs_device *btrfs_find_device_by_path(
-		struct btrfs_fs_info *fs_info, const char *device_path)
+/**
+ * Populate args from device at path
+ *
+ * @fs_info:	the filesystem
+ * @args:	the args to populate
+ * @path:	the path to the device
+ *
+ * This will read the super block of the device at @path and populate @args with
+ * the devid, fsid, and uuid.  This is meant to be used for ioctls that need to
+ * lookup a device to operate on, but need to do it before we take any locks.
+ * This properly handles the special case of "missing" that a user may pass in,
+ * and does some basic sanity checks.  The caller must make sure that @path is
+ * properly NUL terminated before calling in, and must call
+ * btrfs_put_dev_args_from_path() in order to free up the temporary fsid and
+ * uuid buffers.
+ *
+ * Return: 0 for success, -errno for failure
+ */
+int btrfs_get_dev_args_from_path(struct btrfs_fs_info *fs_info,
+				 struct btrfs_dev_lookup_args *args,
+				 const char *path)
 {
-	int ret = 0;
 	struct btrfs_super_block *disk_super;
-	u64 devid;
-	u8 *dev_uuid;
 	struct block_device *bdev;
-	struct btrfs_device *device;
+	int ret;
 
-	ret = btrfs_get_bdev_and_sb(device_path, FMODE_READ,
-				    fs_info->bdev_holder, 0, &bdev, &disk_super);
-	if (ret)
-		return ERR_PTR(ret);
+	if (!path || !path[0])
+		return -EINVAL;
+	if (!strcmp(path, "missing")) {
+		args->missing = true;
+		return 0;
+	}
 
-	devid = btrfs_stack_device_id(&disk_super->dev_item);
-	dev_uuid = disk_super->dev_item.uuid;
+	args->uuid = kzalloc(BTRFS_UUID_SIZE, GFP_KERNEL);
+	args->fsid = kzalloc(BTRFS_FSID_SIZE, GFP_KERNEL);
+	if (!args->uuid || !args->fsid) {
+		btrfs_put_dev_args_from_path(args);
+		return -ENOMEM;
+	}
+
+	ret = btrfs_get_bdev_and_sb(path, FMODE_READ, fs_info->bdev_holder, 0,
+				    &bdev, &disk_super);
+	if (ret) {
+		btrfs_put_dev_args_from_path(args);
+		return ret;
+	}
+
+	args->devid = btrfs_stack_device_id(&disk_super->dev_item);
+	memcpy(args->uuid, disk_super->dev_item.uuid, BTRFS_UUID_SIZE);
 	if (btrfs_fs_incompat(fs_info, METADATA_UUID))
-		device = btrfs_find_device(fs_info->fs_devices, devid, dev_uuid,
-					   disk_super->metadata_uuid);
+		memcpy(args->fsid, disk_super->metadata_uuid, BTRFS_FSID_SIZE);
 	else
-		device = btrfs_find_device(fs_info->fs_devices, devid, dev_uuid,
-					   disk_super->fsid);
-
+		memcpy(args->fsid, disk_super->fsid, BTRFS_FSID_SIZE);
 	btrfs_release_disk_super(disk_super);
-	if (!device)
-		device = ERR_PTR(-ENOENT);
 	blkdev_put(bdev, FMODE_READ);
-	return device;
+	return 0;
 }
 
 /*
- * Lookup a device given by device id, or the path if the id is 0.
- */
+ * Only use this jointly with btrfs_get_dev_args_from_path() because we will
+ * allocate our ->uuid and ->fsid pointers, everybody else uses local variables
+ * that don't need to be freed.
+ */
+void btrfs_put_dev_args_from_path(struct btrfs_dev_lookup_args *args)
+{
+	kfree(args->uuid);
+	kfree(args->fsid);
+	args->uuid = NULL;
+	args->fsid = NULL;
+}
+
 struct btrfs_device *btrfs_find_device_by_devspec(
 		struct btrfs_fs_info *fs_info, u64 devid,
 		const char *device_path)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct btrfs_device *device;
+	int ret;
 
 	if (devid) {
-		device = btrfs_find_device(fs_info->fs_devices, devid, NULL,
-					   NULL);
+		args.devid = devid;
+		device = btrfs_find_device(fs_info->fs_devices, &args);
 		if (!device)
 			return ERR_PTR(-ENOENT);
 		return device;
 	}
 
-	if (!device_path || !device_path[0])
-		return ERR_PTR(-EINVAL);
-
-	if (strcmp(device_path, "missing") == 0) {
-		/* Find first missing device */
-		list_for_each_entry(device, &fs_info->fs_devices->devices,
-				    dev_list) {
-			if (test_bit(BTRFS_DEV_STATE_IN_FS_METADATA,
-				     &device->dev_state) && !device->bdev)
-				return device;
-		}
+	ret = btrfs_get_dev_args_from_path(fs_info, &args, device_path);
+	if (ret)
+		return ERR_PTR(ret);
+	device = btrfs_find_device(fs_info->fs_devices, &args);
+	btrfs_put_dev_args_from_path(&args);
+	if (!device)
 		return ERR_PTR(-ENOENT);
-	}
-
-	return btrfs_find_device_by_path(fs_info, device_path);
+	return device;
 }
 
 /*
@@ -2459,6 +2599,7 @@
  */
 static int btrfs_finish_sprout(struct btrfs_trans_handle *trans)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct btrfs_fs_info *fs_info = trans->fs_info;
 	struct btrfs_root *root = fs_info->chunk_root;
 	struct btrfs_path *path;
@@ -2468,7 +2609,6 @@
 	struct btrfs_key key;
 	u8 fs_uuid[BTRFS_FSID_SIZE];
 	u8 dev_uuid[BTRFS_UUID_SIZE];
-	u64 devid;
 	int ret;
 
 	path = btrfs_alloc_path();
@@ -2480,7 +2620,9 @@
 	key.type = BTRFS_DEV_ITEM_KEY;
 
 	while (1) {
+		btrfs_reserve_chunk_metadata(trans, false);
 		ret = btrfs_search_slot(trans, root, &key, path, 0, 1);
+		btrfs_trans_release_chunk_metadata(trans);
 		if (ret < 0)
 			goto error;
 
@@ -2505,13 +2647,14 @@
 
 		dev_item = btrfs_item_ptr(leaf, path->slots[0],
 					  struct btrfs_dev_item);
-		devid = btrfs_device_id(leaf, dev_item);
+		args.devid = btrfs_device_id(leaf, dev_item);
 		read_extent_buffer(leaf, dev_uuid, btrfs_device_uuid(dev_item),
 				   BTRFS_UUID_SIZE);
 		read_extent_buffer(leaf, fs_uuid, btrfs_device_fsid(dev_item),
 				   BTRFS_FSID_SIZE);
-		device = btrfs_find_device(fs_info->fs_devices, devid, dev_uuid,
-					   fs_uuid);
+		args.uuid = dev_uuid;
+		args.fsid = fs_uuid;
+		device = btrfs_find_device(fs_info->fs_devices, &args);
 		BUG_ON(!device); /* Logic error */
 
 		if (device->fs_devices->seeding) {
@@ -2594,7 +2737,7 @@
 	device->fs_info = fs_info;
 	device->bdev = bdev;
 
-	ret = btrfs_get_dev_zone_info(device);
+	ret = btrfs_get_dev_zone_info(device, false);
 	if (ret)
 		goto error_free_device;
 
@@ -2627,6 +2770,8 @@
 			btrfs_abort_transaction(trans, ret);
 			goto error_trans;
 		}
+		btrfs_assign_next_active_device(fs_info->fs_devices->latest_dev,
+						device);
 	}
 
 	device->fs_devices = fs_devices;
@@ -2733,7 +2878,7 @@
 	btrfs_forget_devices(device_path);
 
 	/* Update ctime/mtime for blkid or udev */
-	update_dev_time(bdev);
+	update_dev_time(device_path);
 
 	return ret;
 
@@ -2826,6 +2971,7 @@
 	struct btrfs_super_block *super_copy = fs_info->super_copy;
 	u64 old_total;
 	u64 diff;
+	int ret;
 
 	if (!test_bit(BTRFS_DEV_STATE_WRITEABLE, &device->dev_state))
 		return -EACCES;
@@ -2854,7 +3000,11 @@
 			      &trans->transaction->dev_update_list);
 	mutex_unlock(&fs_info->chunk_mutex);
 
-	return btrfs_update_device(trans, device);
+	btrfs_reserve_chunk_metadata(trans, false);
+	ret = btrfs_update_device(trans, device);
+	btrfs_trans_release_chunk_metadata(trans);
+
+	return ret;
 }
 
 static int btrfs_free_chunk(struct btrfs_trans_handle *trans, u64 chunk_offset)
@@ -2957,15 +3107,16 @@
 	read_unlock(&em_tree->lock);
 
 	if (!em) {
-		btrfs_crit(fs_info, "unable to find logical %llu length %llu",
+		btrfs_crit(fs_info,
+			   "unable to find chunk map for logical %llu length %llu",
 			   logical, length);
 		return ERR_PTR(-EINVAL);
 	}
 
-	if (em->start > logical || em->start + em->len < logical) {
+	if (em->start > logical || em->start + em->len <= logical) {
 		btrfs_crit(fs_info,
-			   "found a bad mapping, wanted %llu-%llu, found %llu-%llu",
-			   logical, length, em->start, em->start + em->len);
+			   "found a bad chunk map, wanted %llu-%llu, found %llu-%llu",
+			   logical, logical + length, em->start, em->start + em->len);
 		free_extent_map(em);
 		return ERR_PTR(-EINVAL);
 	}
@@ -3096,7 +3247,7 @@
 		const u64 sys_flags = btrfs_system_alloc_profile(fs_info);
 		struct btrfs_block_group *sys_bg;
 
-		sys_bg = btrfs_alloc_chunk(trans, sys_flags);
+		sys_bg = btrfs_create_chunk(trans, sys_flags);
 		if (IS_ERR(sys_bg)) {
 			ret = PTR_ERR(sys_bg);
 			btrfs_abort_transaction(trans, ret);
@@ -3250,7 +3401,18 @@
 			mutex_unlock(&fs_info->reclaim_bgs_lock);
 			goto error;
 		}
-		BUG_ON(ret == 0); /* Corruption */
+		if (ret == 0) {
+			/*
+			 * On the first search we would find chunk tree with
+			 * offset -1, which is not possible. On subsequent
+			 * loops this would find an existing item on an invalid
+			 * offset (one less than the previous one, wrong
+			 * alignment and size).
+			 */
+			ret = -EUCLEAN;
+			mutex_unlock(&fs_info->reclaim_bgs_lock);
+			goto error;
+		}
 
 		ret = btrfs_previous_item(chunk_root, path, key.objectid,
 					  key.type);
@@ -4354,10 +4516,12 @@
 	struct btrfs_fs_info *fs_info = data;
 	int ret = 0;
 
+	sb_start_write(fs_info->sb);
 	mutex_lock(&fs_info->balance_mutex);
 	if (fs_info->balance_ctl)
 		ret = btrfs_balance(fs_info, fs_info->balance_ctl, NULL);
 	mutex_unlock(&fs_info->balance_mutex);
+	sb_end_write(fs_info->sb);
 
 	return ret;
 }
@@ -4535,8 +4699,7 @@
 		}
 	}
 
-	BUG_ON(fs_info->balance_ctl ||
-		test_bit(BTRFS_FS_BALANCE_RUNNING, &fs_info->flags));
+	ASSERT(!test_bit(BTRFS_FS_BALANCE_RUNNING, &fs_info->flags));
 	atomic_dec(&fs_info->balance_cancel_req);
 	mutex_unlock(&fs_info->balance_mutex);
 	return 0;
@@ -4889,8 +5052,10 @@
 			round_down(old_total - diff, fs_info->sectorsize));
 	mutex_unlock(&fs_info->chunk_mutex);
 
+	btrfs_reserve_chunk_metadata(trans, false);
 	/* Now btrfs_update_device() will change the on-disk size. */
 	ret = btrfs_update_device(trans, device);
+	btrfs_trans_release_chunk_metadata(trans);
 	if (ret < 0) {
 		btrfs_abort_transaction(trans, ret);
 		btrfs_end_transaction(trans);
@@ -4973,7 +5138,7 @@
 }
 
 /*
- * Structure used internally for __btrfs_alloc_chunk() function.
+ * Structure used internally for btrfs_create_chunk() function.
  * Wraps needed parameters.
  */
 struct alloc_chunk_ctl {
@@ -5377,7 +5542,7 @@
 	return block_group;
 }
 
-struct btrfs_block_group *btrfs_alloc_chunk(struct btrfs_trans_handle *trans,
+struct btrfs_block_group *btrfs_create_chunk(struct btrfs_trans_handle *trans,
 					    u64 type)
 {
 	struct btrfs_fs_info *info = trans->fs_info;
@@ -5578,12 +5743,12 @@
 	 */
 
 	alloc_profile = btrfs_metadata_alloc_profile(fs_info);
-	meta_bg = btrfs_alloc_chunk(trans, alloc_profile);
+	meta_bg = btrfs_create_chunk(trans, alloc_profile);
 	if (IS_ERR(meta_bg))
 		return PTR_ERR(meta_bg);
 
 	alloc_profile = btrfs_system_alloc_profile(fs_info);
-	sys_bg = btrfs_alloc_chunk(trans, alloc_profile);
+	sys_bg = btrfs_create_chunk(trans, alloc_profile);
 	if (IS_ERR(sys_bg))
 		return PTR_ERR(sys_bg);
 
@@ -5795,7 +5960,7 @@
 }
 
 /* Bubble-sort the stripe set to put the parity/syndrome stripes last */
-static void sort_parity_stripes(struct btrfs_bio *bbio, int num_stripes)
+static void sort_parity_stripes(struct btrfs_io_context *bioc, int num_stripes)
 {
 	int i;
 	int again = 1;
@@ -5804,52 +5969,53 @@
 		again = 0;
 		for (i = 0; i < num_stripes - 1; i++) {
 			/* Swap if parity is on a smaller index */
-			if (bbio->raid_map[i] > bbio->raid_map[i + 1]) {
-				swap(bbio->stripes[i], bbio->stripes[i + 1]);
-				swap(bbio->raid_map[i], bbio->raid_map[i + 1]);
+			if (bioc->raid_map[i] > bioc->raid_map[i + 1]) {
+				swap(bioc->stripes[i], bioc->stripes[i + 1]);
+				swap(bioc->raid_map[i], bioc->raid_map[i + 1]);
 				again = 1;
 			}
 		}
 	}
 }
 
-static struct btrfs_bio *alloc_btrfs_bio(int total_stripes, int real_stripes)
+static struct btrfs_io_context *alloc_btrfs_io_context(int total_stripes,
+						       int real_stripes)
 {
-	struct btrfs_bio *bbio = kzalloc(
-		 /* the size of the btrfs_bio */
-		sizeof(struct btrfs_bio) +
-		/* plus the variable array for the stripes */
-		sizeof(struct btrfs_bio_stripe) * (total_stripes) +
-		/* plus the variable array for the tgt dev */
+	struct btrfs_io_context *bioc = kzalloc(
+		 /* The size of btrfs_io_context */
+		sizeof(struct btrfs_io_context) +
+		/* Plus the variable array for the stripes */
+		sizeof(struct btrfs_io_stripe) * (total_stripes) +
+		/* Plus the variable array for the tgt dev */
 		sizeof(int) * (real_stripes) +
 		/*
-		 * plus the raid_map, which includes both the tgt dev
-		 * and the stripes
+		 * Plus the raid_map, which includes both the tgt dev
+		 * and the stripes.
 		 */
 		sizeof(u64) * (total_stripes),
 		GFP_NOFS|__GFP_NOFAIL);
 
-	atomic_set(&bbio->error, 0);
-	refcount_set(&bbio->refs, 1);
+	atomic_set(&bioc->error, 0);
+	refcount_set(&bioc->refs, 1);
 
-	bbio->tgtdev_map = (int *)(bbio->stripes + total_stripes);
-	bbio->raid_map = (u64 *)(bbio->tgtdev_map + real_stripes);
+	bioc->tgtdev_map = (int *)(bioc->stripes + total_stripes);
+	bioc->raid_map = (u64 *)(bioc->tgtdev_map + real_stripes);
 
-	return bbio;
+	return bioc;
 }
 
-void btrfs_get_bbio(struct btrfs_bio *bbio)
+void btrfs_get_bioc(struct btrfs_io_context *bioc)
 {
-	WARN_ON(!refcount_read(&bbio->refs));
-	refcount_inc(&bbio->refs);
+	WARN_ON(!refcount_read(&bioc->refs));
+	refcount_inc(&bioc->refs);
 }
 
-void btrfs_put_bbio(struct btrfs_bio *bbio)
+void btrfs_put_bioc(struct btrfs_io_context *bioc)
 {
-	if (!bbio)
+	if (!bioc)
 		return;
-	if (refcount_dec_and_test(&bbio->refs))
-		kfree(bbio);
+	if (refcount_dec_and_test(&bioc->refs))
+		kfree(bioc);
 }
 
 /* can REQ_OP_DISCARD be sent with other REQ like REQ_OP_WRITE? */
@@ -5859,11 +6025,11 @@
  */
 static int __btrfs_map_block_for_discard(struct btrfs_fs_info *fs_info,
 					 u64 logical, u64 *length_ret,
-					 struct btrfs_bio **bbio_ret)
+					 struct btrfs_io_context **bioc_ret)
 {
 	struct extent_map *em;
 	struct map_lookup *map;
-	struct btrfs_bio *bbio;
+	struct btrfs_io_context *bioc;
 	u64 length = *length_ret;
 	u64 offset;
 	u64 stripe_nr;
@@ -5882,8 +6048,8 @@
 	int ret = 0;
 	int i;
 
-	/* discard always return a bbio */
-	ASSERT(bbio_ret);
+	/* Discard always returns a bioc. */
+	ASSERT(bioc_ret);
 
 	em = btrfs_get_chunk_map(fs_info, logical, length);
 	if (IS_ERR(em))
@@ -5946,26 +6112,25 @@
 					&stripe_index);
 	}
 
-	bbio = alloc_btrfs_bio(num_stripes, 0);
-	if (!bbio) {
+	bioc = alloc_btrfs_io_context(num_stripes, 0);
+	if (!bioc) {
 		ret = -ENOMEM;
 		goto out;
 	}
 
 	for (i = 0; i < num_stripes; i++) {
-		bbio->stripes[i].physical =
+		bioc->stripes[i].physical =
 			map->stripes[stripe_index].physical +
 			stripe_offset + stripe_nr * map->stripe_len;
-		bbio->stripes[i].dev = map->stripes[stripe_index].dev;
+		bioc->stripes[i].dev = map->stripes[stripe_index].dev;
 
 		if (map->type & (BTRFS_BLOCK_GROUP_RAID0 |
 				 BTRFS_BLOCK_GROUP_RAID10)) {
-			bbio->stripes[i].length = stripes_per_dev *
+			bioc->stripes[i].length = stripes_per_dev *
 				map->stripe_len;
 
 			if (i / sub_stripes < remaining_stripes)
-				bbio->stripes[i].length +=
-					map->stripe_len;
+				bioc->stripes[i].length += map->stripe_len;
 
 			/*
 			 * Special for the first stripe and
@@ -5976,19 +6141,17 @@
 			 *    off     end_off
 			 */
 			if (i < sub_stripes)
-				bbio->stripes[i].length -=
-					stripe_offset;
+				bioc->stripes[i].length -= stripe_offset;
 
 			if (stripe_index >= last_stripe &&
 			    stripe_index <= (last_stripe +
 					     sub_stripes - 1))
-				bbio->stripes[i].length -=
-					stripe_end_offset;
+				bioc->stripes[i].length -= stripe_end_offset;
 
 			if (i == sub_stripes - 1)
 				stripe_offset = 0;
 		} else {
-			bbio->stripes[i].length = length;
+			bioc->stripes[i].length = length;
 		}
 
 		stripe_index++;
@@ -5998,9 +6161,9 @@
 		}
 	}
 
-	*bbio_ret = bbio;
-	bbio->map_type = map->type;
-	bbio->num_stripes = num_stripes;
+	*bioc_ret = bioc;
+	bioc->map_type = map->type;
+	bioc->num_stripes = num_stripes;
 out:
 	free_extent_map(em);
 	return ret;
@@ -6024,7 +6187,7 @@
 					 u64 srcdev_devid, int *mirror_num,
 					 u64 *physical)
 {
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	int num_stripes;
 	int index_srcdev = 0;
 	int found = 0;
@@ -6033,20 +6196,20 @@
 	int ret = 0;
 
 	ret = __btrfs_map_block(fs_info, BTRFS_MAP_GET_READ_MIRRORS,
-				logical, &length, &bbio, 0, 0);
+				logical, &length, &bioc, 0, 0);
 	if (ret) {
-		ASSERT(bbio == NULL);
+		ASSERT(bioc == NULL);
 		return ret;
 	}
 
-	num_stripes = bbio->num_stripes;
+	num_stripes = bioc->num_stripes;
 	if (*mirror_num > num_stripes) {
 		/*
 		 * BTRFS_MAP_GET_READ_MIRRORS does not contain this mirror,
 		 * that means that the requested area is not left of the left
 		 * cursor
 		 */
-		btrfs_put_bbio(bbio);
+		btrfs_put_bioc(bioc);
 		return -EIO;
 	}
 
@@ -6056,7 +6219,7 @@
 	 * pointer to the one of the target drive.
 	 */
 	for (i = 0; i < num_stripes; i++) {
-		if (bbio->stripes[i].dev->devid != srcdev_devid)
+		if (bioc->stripes[i].dev->devid != srcdev_devid)
 			continue;
 
 		/*
@@ -6064,15 +6227,15 @@
 		 * mirror with the lowest physical address
 		 */
 		if (found &&
-		    physical_of_found <= bbio->stripes[i].physical)
+		    physical_of_found <= bioc->stripes[i].physical)
 			continue;
 
 		index_srcdev = i;
 		found = 1;
-		physical_of_found = bbio->stripes[i].physical;
+		physical_of_found = bioc->stripes[i].physical;
 	}
 
-	btrfs_put_bbio(bbio);
+	btrfs_put_bioc(bioc);
 
 	ASSERT(found);
 	if (!found)
@@ -6103,12 +6266,12 @@
 }
 
 static void handle_ops_on_dev_replace(enum btrfs_map_op op,
-				      struct btrfs_bio **bbio_ret,
+				      struct btrfs_io_context **bioc_ret,
 				      struct btrfs_dev_replace *dev_replace,
 				      u64 logical,
 				      int *num_stripes_ret, int *max_errors_ret)
 {
-	struct btrfs_bio *bbio = *bbio_ret;
+	struct btrfs_io_context *bioc = *bioc_ret;
 	u64 srcdev_devid = dev_replace->srcdev->devid;
 	int tgtdev_indexes = 0;
 	int num_stripes = *num_stripes_ret;
@@ -6138,17 +6301,17 @@
 		 */
 		index_where_to_add = num_stripes;
 		for (i = 0; i < num_stripes; i++) {
-			if (bbio->stripes[i].dev->devid == srcdev_devid) {
+			if (bioc->stripes[i].dev->devid == srcdev_devid) {
 				/* write to new disk, too */
-				struct btrfs_bio_stripe *new =
-					bbio->stripes + index_where_to_add;
-				struct btrfs_bio_stripe *old =
-					bbio->stripes + i;
+				struct btrfs_io_stripe *new =
+					bioc->stripes + index_where_to_add;
+				struct btrfs_io_stripe *old =
+					bioc->stripes + i;
 
 				new->physical = old->physical;
 				new->length = old->length;
 				new->dev = dev_replace->tgtdev;
-				bbio->tgtdev_map[i] = index_where_to_add;
+				bioc->tgtdev_map[i] = index_where_to_add;
 				index_where_to_add++;
 				max_errors++;
 				tgtdev_indexes++;
@@ -6168,30 +6331,29 @@
 		 * full copy of the source drive.
 		 */
 		for (i = 0; i < num_stripes; i++) {
-			if (bbio->stripes[i].dev->devid == srcdev_devid) {
+			if (bioc->stripes[i].dev->devid == srcdev_devid) {
 				/*
 				 * In case of DUP, in order to keep it simple,
 				 * only add the mirror with the lowest physical
 				 * address
 				 */
 				if (found &&
-				    physical_of_found <=
-				     bbio->stripes[i].physical)
+				    physical_of_found <= bioc->stripes[i].physical)
 					continue;
 				index_srcdev = i;
 				found = 1;
-				physical_of_found = bbio->stripes[i].physical;
+				physical_of_found = bioc->stripes[i].physical;
 			}
 		}
 		if (found) {
-			struct btrfs_bio_stripe *tgtdev_stripe =
-				bbio->stripes + num_stripes;
+			struct btrfs_io_stripe *tgtdev_stripe =
+				bioc->stripes + num_stripes;
 
 			tgtdev_stripe->physical = physical_of_found;
 			tgtdev_stripe->length =
-				bbio->stripes[index_srcdev].length;
+				bioc->stripes[index_srcdev].length;
 			tgtdev_stripe->dev = dev_replace->tgtdev;
-			bbio->tgtdev_map[index_srcdev] = num_stripes;
+			bioc->tgtdev_map[index_srcdev] = num_stripes;
 
 			tgtdev_indexes++;
 			num_stripes++;
@@ -6200,8 +6362,8 @@
 
 	*num_stripes_ret = num_stripes;
 	*max_errors_ret = max_errors;
-	bbio->num_tgtdevs = tgtdev_indexes;
-	*bbio_ret = bbio;
+	bioc->num_tgtdevs = tgtdev_indexes;
+	*bioc_ret = bioc;
 }
 
 static bool need_full_stripe(enum btrfs_map_op op)
@@ -6304,7 +6466,7 @@
 static int __btrfs_map_block(struct btrfs_fs_info *fs_info,
 			     enum btrfs_map_op op,
 			     u64 logical, u64 *length,
-			     struct btrfs_bio **bbio_ret,
+			     struct btrfs_io_context **bioc_ret,
 			     int mirror_num, int need_raid_map)
 {
 	struct extent_map *em;
@@ -6319,7 +6481,7 @@
 	int num_stripes;
 	int max_errors = 0;
 	int tgtdev_indexes = 0;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	struct btrfs_dev_replace *dev_replace = &fs_info->dev_replace;
 	int dev_replace_is_ongoing = 0;
 	int num_alloc_stripes;
@@ -6328,7 +6490,7 @@
 	u64 raid56_full_stripe_start = (u64)-1;
 	struct btrfs_io_geometry geom;
 
-	ASSERT(bbio_ret);
+	ASSERT(bioc_ret);
 	ASSERT(op != BTRFS_MAP_DISCARD);
 
 	em = btrfs_get_chunk_map(fs_info, logical, *length);
@@ -6472,20 +6634,20 @@
 		tgtdev_indexes = num_stripes;
 	}
 
-	bbio = alloc_btrfs_bio(num_alloc_stripes, tgtdev_indexes);
-	if (!bbio) {
+	bioc = alloc_btrfs_io_context(num_alloc_stripes, tgtdev_indexes);
+	if (!bioc) {
 		ret = -ENOMEM;
 		goto out;
 	}
 
 	for (i = 0; i < num_stripes; i++) {
-		bbio->stripes[i].physical = map->stripes[stripe_index].physical +
+		bioc->stripes[i].physical = map->stripes[stripe_index].physical +
 			stripe_offset + stripe_nr * map->stripe_len;
-		bbio->stripes[i].dev = map->stripes[stripe_index].dev;
+		bioc->stripes[i].dev = map->stripes[stripe_index].dev;
 		stripe_index++;
 	}
 
-	/* build raid_map */
+	/* Build raid_map */
 	if (map->type & BTRFS_BLOCK_GROUP_RAID56_MASK && need_raid_map &&
 	    (need_full_stripe(op) || mirror_num > 1)) {
 		u64 tmp;
@@ -6497,15 +6659,15 @@
 		/* Fill in the logical address of each stripe */
 		tmp = stripe_nr * data_stripes;
 		for (i = 0; i < data_stripes; i++)
-			bbio->raid_map[(i+rot) % num_stripes] =
+			bioc->raid_map[(i + rot) % num_stripes] =
 				em->start + (tmp + i) * map->stripe_len;
 
-		bbio->raid_map[(i+rot) % map->num_stripes] = RAID5_P_STRIPE;
+		bioc->raid_map[(i + rot) % map->num_stripes] = RAID5_P_STRIPE;
 		if (map->type & BTRFS_BLOCK_GROUP_RAID6)
-			bbio->raid_map[(i+rot+1) % num_stripes] =
+			bioc->raid_map[(i + rot + 1) % num_stripes] =
 				RAID6_Q_STRIPE;
 
-		sort_parity_stripes(bbio, num_stripes);
+		sort_parity_stripes(bioc, num_stripes);
 	}
 
 	if (need_full_stripe(op))
@@ -6513,15 +6675,15 @@
 
 	if (dev_replace_is_ongoing && dev_replace->tgtdev != NULL &&
 	    need_full_stripe(op)) {
-		handle_ops_on_dev_replace(op, &bbio, dev_replace, logical,
+		handle_ops_on_dev_replace(op, &bioc, dev_replace, logical,
 					  &num_stripes, &max_errors);
 	}
 
-	*bbio_ret = bbio;
-	bbio->map_type = map->type;
-	bbio->num_stripes = num_stripes;
-	bbio->max_errors = max_errors;
-	bbio->mirror_num = mirror_num;
+	*bioc_ret = bioc;
+	bioc->map_type = map->type;
+	bioc->num_stripes = num_stripes;
+	bioc->max_errors = max_errors;
+	bioc->mirror_num = mirror_num;
 
 	/*
 	 * this is the case that REQ_READ && dev_replace_is_ongoing &&
@@ -6530,9 +6692,9 @@
 	 */
 	if (patch_the_first_stripe_for_dev_replace && num_stripes > 0) {
 		WARN_ON(num_stripes > 1);
-		bbio->stripes[0].dev = dev_replace->tgtdev;
-		bbio->stripes[0].physical = physical_to_patch_in_first_stripe;
-		bbio->mirror_num = map->num_stripes + 1;
+		bioc->stripes[0].dev = dev_replace->tgtdev;
+		bioc->stripes[0].physical = physical_to_patch_in_first_stripe;
+		bioc->mirror_num = map->num_stripes + 1;
 	}
 out:
 	if (dev_replace_is_ongoing) {
@@ -6546,40 +6708,40 @@
 
 int btrfs_map_block(struct btrfs_fs_info *fs_info, enum btrfs_map_op op,
 		      u64 logical, u64 *length,
-		      struct btrfs_bio **bbio_ret, int mirror_num)
+		      struct btrfs_io_context **bioc_ret, int mirror_num)
 {
 	if (op == BTRFS_MAP_DISCARD)
 		return __btrfs_map_block_for_discard(fs_info, logical,
-						     length, bbio_ret);
+						     length, bioc_ret);
 
-	return __btrfs_map_block(fs_info, op, logical, length, bbio_ret,
+	return __btrfs_map_block(fs_info, op, logical, length, bioc_ret,
 				 mirror_num, 0);
 }
 
 /* For Scrub/replace */
 int btrfs_map_sblock(struct btrfs_fs_info *fs_info, enum btrfs_map_op op,
 		     u64 logical, u64 *length,
-		     struct btrfs_bio **bbio_ret)
+		     struct btrfs_io_context **bioc_ret)
 {
-	return __btrfs_map_block(fs_info, op, logical, length, bbio_ret, 0, 1);
+	return __btrfs_map_block(fs_info, op, logical, length, bioc_ret, 0, 1);
 }
 
-static inline void btrfs_end_bbio(struct btrfs_bio *bbio, struct bio *bio)
+static inline void btrfs_end_bioc(struct btrfs_io_context *bioc, struct bio *bio)
 {
-	bio->bi_private = bbio->private;
-	bio->bi_end_io = bbio->end_io;
+	bio->bi_private = bioc->private;
+	bio->bi_end_io = bioc->end_io;
 	bio_endio(bio);
 
-	btrfs_put_bbio(bbio);
+	btrfs_put_bioc(bioc);
 }
 
 static void btrfs_end_bio(struct bio *bio)
 {
-	struct btrfs_bio *bbio = bio->bi_private;
+	struct btrfs_io_context *bioc = bio->bi_private;
 	int is_orig_bio = 0;
 
 	if (bio->bi_status) {
-		atomic_inc(&bbio->error);
+		atomic_inc(&bioc->error);
 		if (bio->bi_status == BLK_STS_IOERR ||
 		    bio->bi_status == BLK_STS_TARGET) {
 			struct btrfs_device *dev = btrfs_io_bio(bio)->device;
@@ -6597,22 +6759,22 @@
 		}
 	}
 
-	if (bio == bbio->orig_bio)
+	if (bio == bioc->orig_bio)
 		is_orig_bio = 1;
 
-	btrfs_bio_counter_dec(bbio->fs_info);
+	btrfs_bio_counter_dec(bioc->fs_info);
 
-	if (atomic_dec_and_test(&bbio->stripes_pending)) {
+	if (atomic_dec_and_test(&bioc->stripes_pending)) {
 		if (!is_orig_bio) {
 			bio_put(bio);
-			bio = bbio->orig_bio;
+			bio = bioc->orig_bio;
 		}
 
-		btrfs_io_bio(bio)->mirror_num = bbio->mirror_num;
+		btrfs_io_bio(bio)->mirror_num = bioc->mirror_num;
 		/* only send an error to the higher layers if it is
 		 * beyond the tolerance of the btrfs bio
 		 */
-		if (atomic_read(&bbio->error) > bbio->max_errors) {
+		if (atomic_read(&bioc->error) > bioc->max_errors) {
 			bio->bi_status = BLK_STS_IOERR;
 		} else {
 			/*
@@ -6622,18 +6784,18 @@
 			bio->bi_status = BLK_STS_OK;
 		}
 
-		btrfs_end_bbio(bbio, bio);
+		btrfs_end_bioc(bioc, bio);
 	} else if (!is_orig_bio) {
 		bio_put(bio);
 	}
 }
 
-static void submit_stripe_bio(struct btrfs_bio *bbio, struct bio *bio,
+static void submit_stripe_bio(struct btrfs_io_context *bioc, struct bio *bio,
 			      u64 physical, struct btrfs_device *dev)
 {
-	struct btrfs_fs_info *fs_info = bbio->fs_info;
+	struct btrfs_fs_info *fs_info = bioc->fs_info;
 
-	bio->bi_private = bbio;
+	bio->bi_private = bioc;
 	btrfs_io_bio(bio)->device = dev;
 	bio->bi_end_io = btrfs_end_bio;
 	bio->bi_iter.bi_sector = physical >> 9;
@@ -6663,20 +6825,20 @@
 	btrfsic_submit_bio(bio);
 }
 
-static void bbio_error(struct btrfs_bio *bbio, struct bio *bio, u64 logical)
+static void bioc_error(struct btrfs_io_context *bioc, struct bio *bio, u64 logical)
 {
-	atomic_inc(&bbio->error);
-	if (atomic_dec_and_test(&bbio->stripes_pending)) {
+	atomic_inc(&bioc->error);
+	if (atomic_dec_and_test(&bioc->stripes_pending)) {
 		/* Should be the original bio. */
-		WARN_ON(bio != bbio->orig_bio);
+		WARN_ON(bio != bioc->orig_bio);
 
-		btrfs_io_bio(bio)->mirror_num = bbio->mirror_num;
+		btrfs_io_bio(bio)->mirror_num = bioc->mirror_num;
 		bio->bi_iter.bi_sector = logical >> 9;
-		if (atomic_read(&bbio->error) > bbio->max_errors)
+		if (atomic_read(&bioc->error) > bioc->max_errors)
 			bio->bi_status = BLK_STS_IOERR;
 		else
 			bio->bi_status = BLK_STS_OK;
-		btrfs_end_bbio(bbio, bio);
+		btrfs_end_bioc(bioc, bio);
 	}
 }
 
@@ -6691,35 +6853,35 @@
 	int ret;
 	int dev_nr;
 	int total_devs;
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 
 	length = bio->bi_iter.bi_size;
 	map_length = length;
 
 	btrfs_bio_counter_inc_blocked(fs_info);
 	ret = __btrfs_map_block(fs_info, btrfs_op(bio), logical,
-				&map_length, &bbio, mirror_num, 1);
+				&map_length, &bioc, mirror_num, 1);
 	if (ret) {
 		btrfs_bio_counter_dec(fs_info);
 		return errno_to_blk_status(ret);
 	}
 
-	total_devs = bbio->num_stripes;
-	bbio->orig_bio = first_bio;
-	bbio->private = first_bio->bi_private;
-	bbio->end_io = first_bio->bi_end_io;
-	bbio->fs_info = fs_info;
-	atomic_set(&bbio->stripes_pending, bbio->num_stripes);
+	total_devs = bioc->num_stripes;
+	bioc->orig_bio = first_bio;
+	bioc->private = first_bio->bi_private;
+	bioc->end_io = first_bio->bi_end_io;
+	bioc->fs_info = fs_info;
+	atomic_set(&bioc->stripes_pending, bioc->num_stripes);
 
-	if ((bbio->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK) &&
+	if ((bioc->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK) &&
 	    ((btrfs_op(bio) == BTRFS_MAP_WRITE) || (mirror_num > 1))) {
 		/* In this case, map_length has been set to the length of
 		   a single stripe; not the whole write */
 		if (btrfs_op(bio) == BTRFS_MAP_WRITE) {
-			ret = raid56_parity_write(fs_info, bio, bbio,
+			ret = raid56_parity_write(fs_info, bio, bioc,
 						  map_length);
 		} else {
-			ret = raid56_parity_recover(fs_info, bio, bbio,
+			ret = raid56_parity_recover(fs_info, bio, bioc,
 						    map_length, mirror_num, 1);
 		}
 
@@ -6735,12 +6897,12 @@
 	}
 
 	for (dev_nr = 0; dev_nr < total_devs; dev_nr++) {
-		dev = bbio->stripes[dev_nr].dev;
+		dev = bioc->stripes[dev_nr].dev;
 		if (!dev || !dev->bdev || test_bit(BTRFS_DEV_STATE_MISSING,
 						   &dev->dev_state) ||
 		    (btrfs_op(first_bio) == BTRFS_MAP_WRITE &&
 		    !test_bit(BTRFS_DEV_STATE_WRITEABLE, &dev->dev_state))) {
-			bbio_error(bbio, first_bio, logical);
+			bioc_error(bioc, first_bio, logical);
 			continue;
 		}
 
@@ -6749,12 +6911,39 @@
 		else
 			bio = first_bio;
 
-		submit_stripe_bio(bbio, bio, bbio->stripes[dev_nr].physical, dev);
+		submit_stripe_bio(bioc, bio, bioc->stripes[dev_nr].physical, dev);
 	}
 	btrfs_bio_counter_dec(fs_info);
 	return BLK_STS_OK;
 }
 
+static bool dev_args_match_fs_devices(const struct btrfs_dev_lookup_args *args,
+				      const struct btrfs_fs_devices *fs_devices)
+{
+	if (args->fsid == NULL)
+		return true;
+	if (memcmp(fs_devices->metadata_uuid, args->fsid, BTRFS_FSID_SIZE) == 0)
+		return true;
+	return false;
+}
+
+static bool dev_args_match_device(const struct btrfs_dev_lookup_args *args,
+				  const struct btrfs_device *device)
+{
+	if (args->missing) {
+		if (test_bit(BTRFS_DEV_STATE_IN_FS_METADATA, &device->dev_state) &&
+		    !device->bdev)
+			return true;
+		return false;
+	}
+
+	if (device->devid != args->devid)
+		return false;
+	if (args->uuid && memcmp(device->uuid, args->uuid, BTRFS_UUID_SIZE) != 0)
+		return false;
+	return true;
+}
+
 /*
  * Find a device specified by @devid or @uuid in the list of @fs_devices, or
  * return NULL.
@@ -6762,31 +6951,25 @@
  * If devid and uuid are both specified, the match must be exact, otherwise
  * only devid is used.
  */
-struct btrfs_device *btrfs_find_device(struct btrfs_fs_devices *fs_devices,
-				       u64 devid, u8 *uuid, u8 *fsid)
+struct btrfs_device *btrfs_find_device(const struct btrfs_fs_devices *fs_devices,
+				       const struct btrfs_dev_lookup_args *args)
 {
 	struct btrfs_device *device;
 	struct btrfs_fs_devices *seed_devs;
 
-	if (!fsid || !memcmp(fs_devices->metadata_uuid, fsid, BTRFS_FSID_SIZE)) {
+	if (dev_args_match_fs_devices(args, fs_devices)) {
 		list_for_each_entry(device, &fs_devices->devices, dev_list) {
-			if (device->devid == devid &&
-			    (!uuid || memcmp(device->uuid, uuid,
-					     BTRFS_UUID_SIZE) == 0))
+			if (dev_args_match_device(args, device))
 				return device;
 		}
 	}
 
 	list_for_each_entry(seed_devs, &fs_devices->seed_list, seed_list) {
-		if (!fsid ||
-		    !memcmp(seed_devs->metadata_uuid, fsid, BTRFS_FSID_SIZE)) {
-			list_for_each_entry(device, &seed_devs->devices,
-					    dev_list) {
-				if (device->devid == devid &&
-				    (!uuid || memcmp(device->uuid, uuid,
-						     BTRFS_UUID_SIZE) == 0))
-					return device;
-			}
+		if (!dev_args_match_fs_devices(args, seed_devs))
+			continue;
+		list_for_each_entry(device, &seed_devs->devices, dev_list) {
+			if (dev_args_match_device(args, device))
+				return device;
 		}
 	}
 
@@ -6949,9 +7132,31 @@
 }
 #endif
 
+static struct btrfs_device *handle_missing_device(struct btrfs_fs_info *fs_info,
+						  u64 devid, u8 *uuid)
+{
+	struct btrfs_device *dev;
+
+	if (!btrfs_test_opt(fs_info, DEGRADED)) {
+		btrfs_report_missing_device(fs_info, devid, uuid, true);
+		return ERR_PTR(-ENOENT);
+	}
+
+	dev = add_missing_dev(fs_info->fs_devices, devid, uuid);
+	if (IS_ERR(dev)) {
+		btrfs_err(fs_info, "failed to init missing device %llu: %ld",
+			  devid, PTR_ERR(dev));
+		return dev;
+	}
+	btrfs_report_missing_device(fs_info, devid, uuid, false);
+
+	return dev;
+}
+
 static int read_one_chunk(struct btrfs_key *key, struct extent_buffer *leaf,
 			  struct btrfs_chunk *chunk)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct btrfs_fs_info *fs_info = leaf->fs_info;
 	struct extent_map_tree *map_tree = &fs_info->mapping_tree;
 	struct map_lookup *map;
@@ -7029,33 +7234,24 @@
 		map->stripes[i].physical =
 			btrfs_stripe_offset_nr(leaf, chunk, i);
 		devid = btrfs_stripe_devid_nr(leaf, chunk, i);
+		args.devid = devid;
 		read_extent_buffer(leaf, uuid, (unsigned long)
 				   btrfs_stripe_dev_uuid_nr(chunk, i),
 				   BTRFS_UUID_SIZE);
-		map->stripes[i].dev = btrfs_find_device(fs_info->fs_devices,
-							devid, uuid, NULL);
-		if (!map->stripes[i].dev &&
-		    !btrfs_test_opt(fs_info, DEGRADED)) {
-			free_extent_map(em);
-			btrfs_report_missing_device(fs_info, devid, uuid, true);
-			return -ENOENT;
-		}
+		args.uuid = uuid;
+		map->stripes[i].dev = btrfs_find_device(fs_info->fs_devices, &args);
 		if (!map->stripes[i].dev) {
-			map->stripes[i].dev =
-				add_missing_dev(fs_info->fs_devices, devid,
-						uuid);
+			map->stripes[i].dev = handle_missing_device(fs_info,
+								    devid, uuid);
 			if (IS_ERR(map->stripes[i].dev)) {
+				ret = PTR_ERR(map->stripes[i].dev);
 				free_extent_map(em);
-				btrfs_err(fs_info,
-					"failed to init missing dev %llu: %ld",
-					devid, PTR_ERR(map->stripes[i].dev));
-				return PTR_ERR(map->stripes[i].dev);
+				return ret;
 			}
-			btrfs_report_missing_device(fs_info, devid, uuid, false);
 		}
+
 		set_bit(BTRFS_DEV_STATE_IN_FS_METADATA,
 				&(map->stripes[i].dev->dev_state));
-
 	}
 
 	write_lock(&map_tree->lock);
@@ -7151,6 +7347,7 @@
 static int read_one_dev(struct extent_buffer *leaf,
 			struct btrfs_dev_item *dev_item)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct btrfs_fs_info *fs_info = leaf->fs_info;
 	struct btrfs_fs_devices *fs_devices = fs_info->fs_devices;
 	struct btrfs_device *device;
@@ -7159,11 +7356,13 @@
 	u8 fs_uuid[BTRFS_FSID_SIZE];
 	u8 dev_uuid[BTRFS_UUID_SIZE];
 
-	devid = btrfs_device_id(leaf, dev_item);
+	devid = args.devid = btrfs_device_id(leaf, dev_item);
 	read_extent_buffer(leaf, dev_uuid, btrfs_device_uuid(dev_item),
 			   BTRFS_UUID_SIZE);
 	read_extent_buffer(leaf, fs_uuid, btrfs_device_fsid(dev_item),
 			   BTRFS_FSID_SIZE);
+	args.uuid = dev_uuid;
+	args.fsid = fs_uuid;
 
 	if (memcmp(fs_uuid, fs_devices->metadata_uuid, BTRFS_FSID_SIZE)) {
 		fs_devices = open_seed_devices(fs_info, fs_uuid);
@@ -7171,8 +7370,7 @@
 			return PTR_ERR(fs_devices);
 	}
 
-	device = btrfs_find_device(fs_info->fs_devices, devid, dev_uuid,
-				   fs_uuid);
+	device = btrfs_find_device(fs_info->fs_devices, &args);
 	if (!device) {
 		if (!btrfs_test_opt(fs_info, DEGRADED)) {
 			btrfs_report_missing_device(fs_info, devid,
@@ -7482,6 +7680,19 @@
 	fs_info->fs_devices->total_rw_bytes = 0;
 
 	/*
+	 * Lockdep complains about possible circular locking dependency between
+	 * a disk's open_mutex (struct gendisk.open_mutex), the rw semaphores
+	 * used for freeze procection of a fs (struct super_block.s_writers),
+	 * which we take when starting a transaction, and extent buffers of the
+	 * chunk tree if we call read_one_dev() while holding a lock on an
+	 * extent buffer of the chunk tree. Since we are mounting the filesystem
+	 * and at this point there can't be any concurrent task modifying the
+	 * chunk tree, to keep it simple, just skip locking on the chunk tree.
+	 */
+	ASSERT(!test_bit(BTRFS_FS_OPEN, &fs_info->flags));
+	path->skip_locking = 1;
+
+	/*
 	 * Read all device items, and then all the chunk items. All
 	 * device items are found before any chunk item (their object id
 	 * is smaller than the lowest possible object id for a chunk
@@ -7506,10 +7717,6 @@
 				goto error;
 			break;
 		}
-		/*
-		 * The nodes on level 1 are not locked but we don't need to do
-		 * that during mount time as nothing else can access the tree
-		 */
 		node = path->nodes[1];
 		if (node) {
 			if (last_ra_node != node->start) {
@@ -7537,7 +7744,6 @@
 			 * requirement for chunk allocation, see the comment on
 			 * top of btrfs_chunk_alloc() for details.
 			 */
-			ASSERT(!test_bit(BTRFS_FS_OPEN, &fs_info->flags));
 			chunk = btrfs_item_ptr(leaf, slot, struct btrfs_chunk);
 			ret = read_one_chunk(&found_key, leaf, chunk);
 			if (ret)
@@ -7551,12 +7757,12 @@
 	 * do another round of validation checks.
 	 */
 	if (total_dev != fs_info->fs_devices->total_devices) {
-		btrfs_err(fs_info,
-	   "super_num_devices %llu mismatch with num_devices %llu found here",
+		btrfs_warn(fs_info,
+"super block num_devices %llu mismatch with DEV_ITEM count %llu, will be repaired on next transaction commit",
 			  btrfs_super_num_devices(fs_info->super_copy),
 			  total_dev);
-		ret = -EINVAL;
-		goto error;
+		fs_info->fs_devices->total_devices = total_dev;
+		btrfs_set_super_num_devices(fs_info->super_copy, total_dev);
 	}
 	if (btrfs_super_total_bytes(fs_info->super_copy) <
 	    fs_info->fs_devices->total_rw_bytes) {
@@ -7575,10 +7781,11 @@
 	return ret;
 }
 
-void btrfs_init_devices_late(struct btrfs_fs_info *fs_info)
+int btrfs_init_devices_late(struct btrfs_fs_info *fs_info)
 {
 	struct btrfs_fs_devices *fs_devices = fs_info->fs_devices, *seed_devs;
 	struct btrfs_device *device;
+	int ret = 0;
 
 	fs_devices->fs_info = fs_info;
 
@@ -7587,12 +7794,18 @@
 		device->fs_info = fs_info;
 
 	list_for_each_entry(seed_devs, &fs_devices->seed_list, seed_list) {
-		list_for_each_entry(device, &seed_devs->devices, dev_list)
+		list_for_each_entry(device, &seed_devs->devices, dev_list) {
 			device->fs_info = fs_info;
+			ret = btrfs_get_dev_zone_info(device, false);
+			if (ret)
+				break;
+		}
 
 		seed_devs->fs_info = fs_info;
 	}
 	mutex_unlock(&fs_devices->device_list_mutex);
+
+	return ret;
 }
 
 static u64 btrfs_dev_stats_value(const struct extent_buffer *eb,
@@ -7841,12 +8054,14 @@
 int btrfs_get_dev_stats(struct btrfs_fs_info *fs_info,
 			struct btrfs_ioctl_get_dev_stats *stats)
 {
+	BTRFS_DEV_LOOKUP_ARGS(args);
 	struct btrfs_device *dev;
 	struct btrfs_fs_devices *fs_devices = fs_info->fs_devices;
 	int i;
 
 	mutex_lock(&fs_devices->device_list_mutex);
-	dev = btrfs_find_device(fs_info->fs_devices, stats->devid, NULL, NULL);
+	args.devid = stats->devid;
+	dev = btrfs_find_device(fs_info->fs_devices, &args);
 	mutex_unlock(&fs_devices->device_list_mutex);
 
 	if (!dev) {
@@ -7922,6 +8137,7 @@
 				 u64 chunk_offset, u64 devid,
 				 u64 physical_offset, u64 physical_len)
 {
+	struct btrfs_dev_lookup_args args = { .devid = devid };
 	struct extent_map_tree *em_tree = &fs_info->mapping_tree;
 	struct extent_map *em;
 	struct map_lookup *map;
@@ -7977,7 +8193,7 @@
 	}
 
 	/* Make sure no dev extent is beyond device boundary */
-	dev = btrfs_find_device(fs_info->fs_devices, devid, NULL, NULL);
+	dev = btrfs_find_device(fs_info->fs_devices, &args);
 	if (!dev) {
 		btrfs_err(fs_info, "failed to find devid %llu", devid);
 		ret = -EUCLEAN;
@@ -8173,10 +8389,12 @@
 	target = cache->start;
 	btrfs_put_block_group(cache);
 
+	sb_start_write(fs_info->sb);
 	if (!btrfs_exclop_start(fs_info, BTRFS_EXCLOP_BALANCE)) {
 		btrfs_info(fs_info,
 			   "zoned: skip relocating block group %llu to repair: EBUSY",
 			   target);
+		sb_end_write(fs_info->sb);
 		return -EBUSY;
 	}
 
@@ -8204,6 +8422,7 @@
 		btrfs_put_block_group(cache);
 	mutex_unlock(&fs_info->reclaim_bgs_lock);
 	btrfs_exclop_finish(fs_info);
+	sb_end_write(fs_info->sb);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/volumes.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/volumes.h
@@ -246,7 +246,11 @@
 	/* Highest generation number of seen devices */
 	u64 latest_generation;
 
-	struct block_device *latest_bdev;
+	/*
+	 * The mount device or a device with highest generation after removal
+	 * or replace.
+	 */
+	struct btrfs_device *latest_dev;
 
 	/* all of the devices in the FS, protected by a mutex
 	 * so we can safely walk it to write out the supers without
@@ -302,11 +306,11 @@
 /*
  * we need the mirror number and stripe index to be passed around
  * the call chain while we are processing end_io (especially errors).
- * Really, what we need is a btrfs_bio structure that has this info
+ * Really, what we need is a btrfs_io_context structure that has this info
  * and is properly sized with its stripe array, but we're not there
  * quite yet.  We have our own btrfs bioset, and all of the bios
  * we allocate are actually btrfs_io_bios.  We'll cram as much of
- * struct btrfs_bio as we can into this over time.
+ * struct btrfs_io_context as we can into this over time.
  */
 struct btrfs_io_bio {
 	unsigned int mirror_num;
@@ -335,13 +339,29 @@
 	}
 }
 
-struct btrfs_bio_stripe {
+struct btrfs_io_stripe {
 	struct btrfs_device *dev;
 	u64 physical;
 	u64 length; /* only used for discard mappings */
 };
 
-struct btrfs_bio {
+/*
+ * Context for IO subsmission for device stripe.
+ *
+ * - Track the unfinished mirrors for mirror based profiles
+ *   Mirror based profiles are SINGLE/DUP/RAID1/RAID10.
+ *
+ * - Contain the logical -> physical mapping info
+ *   Used by submit_stripe_bio() for mapping logical bio
+ *   into physical device address.
+ *
+ * - Contain device replace info
+ *   Used by handle_ops_on_dev_replace() to copy logical bios
+ *   into the new device.
+ *
+ * - Contain RAID56 full stripe logical bytenrs
+ */
+struct btrfs_io_context {
 	refcount_t refs;
 	atomic_t stripes_pending;
 	struct btrfs_fs_info *fs_info;
@@ -361,7 +381,7 @@
 	 * so raid_map[0] is the start of our full stripe
 	 */
 	u64 *raid_map;
-	struct btrfs_bio_stripe stripes[];
+	struct btrfs_io_stripe stripes[];
 };
 
 struct btrfs_device_info {
@@ -396,11 +416,11 @@
 	int num_stripes;
 	int sub_stripes;
 	int verified_stripes; /* For mount time dev extent verification */
-	struct btrfs_bio_stripe stripes[];
+	struct btrfs_io_stripe stripes[];
 };
 
 #define map_lookup_size(n) (sizeof(struct map_lookup) + \
-			    (sizeof(struct btrfs_bio_stripe) * (n)))
+			    (sizeof(struct btrfs_io_stripe) * (n)))
 
 struct btrfs_balance_args;
 struct btrfs_balance_progress;
@@ -414,6 +434,22 @@
 	struct btrfs_balance_progress stat;
 };
 
+/*
+ * Search for a given device by the set parameters
+ */
+struct btrfs_dev_lookup_args {
+	u64 devid;
+	u8 *uuid;
+	u8 *fsid;
+	bool missing;
+};
+
+/* We have to initialize to -1 because BTRFS_DEV_REPLACE_DEVID is 0 */
+#define BTRFS_DEV_LOOKUP_ARGS_INIT { .devid = (u64)-1 }
+
+#define BTRFS_DEV_LOOKUP_ARGS(name) \
+	struct btrfs_dev_lookup_args name = BTRFS_DEV_LOOKUP_ARGS_INIT
+
 enum btrfs_map_op {
 	BTRFS_MAP_READ,
 	BTRFS_MAP_WRITE,
@@ -437,20 +473,20 @@
 	}
 }
 
-void btrfs_get_bbio(struct btrfs_bio *bbio);
-void btrfs_put_bbio(struct btrfs_bio *bbio);
+void btrfs_get_bioc(struct btrfs_io_context *bioc);
+void btrfs_put_bioc(struct btrfs_io_context *bioc);
 int btrfs_map_block(struct btrfs_fs_info *fs_info, enum btrfs_map_op op,
 		    u64 logical, u64 *length,
-		    struct btrfs_bio **bbio_ret, int mirror_num);
+		    struct btrfs_io_context **bioc_ret, int mirror_num);
 int btrfs_map_sblock(struct btrfs_fs_info *fs_info, enum btrfs_map_op op,
 		     u64 logical, u64 *length,
-		     struct btrfs_bio **bbio_ret);
+		     struct btrfs_io_context **bioc_ret);
 int btrfs_get_io_geometry(struct btrfs_fs_info *fs_info, struct extent_map *map,
 			  enum btrfs_map_op op, u64 logical,
 			  struct btrfs_io_geometry *io_geom);
 int btrfs_read_sys_array(struct btrfs_fs_info *fs_info);
 int btrfs_read_chunk_tree(struct btrfs_fs_info *fs_info);
-struct btrfs_block_group *btrfs_alloc_chunk(struct btrfs_trans_handle *trans,
+struct btrfs_block_group *btrfs_create_chunk(struct btrfs_trans_handle *trans,
 					    u64 type);
 void btrfs_mapping_tree_free(struct extent_map_tree *tree);
 blk_status_t btrfs_map_bio(struct btrfs_fs_info *fs_info, struct bio *bio,
@@ -467,19 +503,23 @@
 struct btrfs_device *btrfs_find_device_by_devspec(struct btrfs_fs_info *fs_info,
 						  u64 devid,
 						  const char *devpath);
+int btrfs_get_dev_args_from_path(struct btrfs_fs_info *fs_info,
+				 struct btrfs_dev_lookup_args *args,
+				 const char *path);
 struct btrfs_device *btrfs_alloc_device(struct btrfs_fs_info *fs_info,
 					const u64 *devid,
 					const u8 *uuid);
+void btrfs_put_dev_args_from_path(struct btrfs_dev_lookup_args *args);
 void btrfs_free_device(struct btrfs_device *device);
 int btrfs_rm_device(struct btrfs_fs_info *fs_info,
-		    const char *device_path, u64 devid,
+		    struct btrfs_dev_lookup_args *args,
 		    struct block_device **bdev, fmode_t *mode);
 void __exit btrfs_cleanup_fs_uuids(void);
 int btrfs_num_copies(struct btrfs_fs_info *fs_info, u64 logical, u64 len);
 int btrfs_grow_device(struct btrfs_trans_handle *trans,
 		      struct btrfs_device *device, u64 new_size);
-struct btrfs_device *btrfs_find_device(struct btrfs_fs_devices *fs_devices,
-				       u64 devid, u8 *uuid, u8 *fsid);
+struct btrfs_device *btrfs_find_device(const struct btrfs_fs_devices *fs_devices,
+				       const struct btrfs_dev_lookup_args *args);
 int btrfs_shrink_device(struct btrfs_device *device, u64 new_size);
 int btrfs_init_new_device(struct btrfs_fs_info *fs_info, const char *path);
 int btrfs_balance(struct btrfs_fs_info *fs_info,
@@ -499,7 +539,7 @@
 void btrfs_dev_stat_inc_and_print(struct btrfs_device *dev, int index);
 int btrfs_get_dev_stats(struct btrfs_fs_info *fs_info,
 			struct btrfs_ioctl_get_dev_stats *stats);
-void btrfs_init_devices_late(struct btrfs_fs_info *fs_info);
+int btrfs_init_devices_late(struct btrfs_fs_info *fs_info);
 int btrfs_init_dev_stats(struct btrfs_fs_info *fs_info);
 int btrfs_run_dev_stats(struct btrfs_trans_handle *trans);
 void btrfs_rm_dev_replace_remove_srcdev(struct btrfs_device *srcdev);
@@ -582,4 +622,7 @@
 int btrfs_verify_dev_extents(struct btrfs_fs_info *fs_info);
 int btrfs_repair_one_zone(struct btrfs_fs_info *fs_info, u64 logical);
 
+bool btrfs_pinned_by_swapfile(struct btrfs_fs_info *fs_info, void *ptr);
+u8 *btrfs_sb_fsid_ptr(struct btrfs_super_block *sb);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/xattr.c
@@ -264,7 +264,8 @@
 	inode_inc_iversion(inode);
 	inode->i_ctime = current_time(inode);
 	ret = btrfs_update_inode(trans, root, BTRFS_I(inode));
-	BUG_ON(ret);
+	if (ret)
+		btrfs_abort_transaction(trans, ret);
 out:
 	if (start_trans)
 		btrfs_end_transaction(trans);
@@ -390,6 +391,9 @@
 				   const char *name, const void *buffer,
 				   size_t size, int flags)
 {
+	if (btrfs_root_readonly(BTRFS_I(inode)->root))
+		return -EROFS;
+
 	name = xattr_full_name(handler, name);
 	return btrfs_setxattr_trans(inode, name, buffer, size, flags);
 }
@@ -418,7 +422,8 @@
 		inode_inc_iversion(inode);
 		inode->i_ctime = current_time(inode);
 		ret = btrfs_update_inode(trans, root, BTRFS_I(inode));
-		BUG_ON(ret);
+		if (ret)
+			btrfs_abort_transaction(trans, ret);
 	}
 
 	btrfs_end_transaction(trans);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/zlib.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/zlib.c
@@ -63,7 +63,7 @@
 
 	workspacesize = max(zlib_deflate_workspacesize(MAX_WBITS, MAX_MEM_LEVEL),
 			zlib_inflate_workspacesize());
-	workspace->strm.workspace = kvmalloc(workspacesize, GFP_KERNEL);
+	workspace->strm.workspace = kvzalloc(workspacesize, GFP_KERNEL);
 	workspace->level = level;
 	workspace->buf = NULL;
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/zoned.c
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/zoned.c
@@ -4,6 +4,7 @@
 #include <linux/slab.h>
 #include <linux/blkdev.h>
 #include <linux/sched/mm.h>
+#include <linux/vmalloc.h>
 #include "ctree.h"
 #include "volumes.h"
 #include "zoned.h"
@@ -113,7 +114,8 @@
 			super[i] = page_address(page[i]);
 		}
 
-		if (super[0]->generation > super[1]->generation)
+		if (btrfs_super_generation(super[0]) >
+		    btrfs_super_generation(super[1]))
 			sector = zones[1].start;
 		else
 			sector = zones[0].start;
@@ -195,6 +197,8 @@
 static int btrfs_get_dev_zones(struct btrfs_device *device, u64 pos,
 			       struct blk_zone *zones, unsigned int *nr_zones)
 {
+	struct btrfs_zoned_device_info *zinfo = device->zone_info;
+	u32 zno;
 	int ret;
 
 	if (!*nr_zones)
@@ -206,6 +210,34 @@
 		return 0;
 	}
 
+	/* Check cache */
+	if (zinfo->zone_cache) {
+		unsigned int i;
+
+		ASSERT(IS_ALIGNED(pos, zinfo->zone_size));
+		zno = pos >> zinfo->zone_size_shift;
+		/*
+		 * We cannot report zones beyond the zone end. So, it is OK to
+		 * cap *nr_zones to at the end.
+		 */
+		*nr_zones = min_t(u32, *nr_zones, zinfo->nr_zones - zno);
+
+		for (i = 0; i < *nr_zones; i++) {
+			struct blk_zone *zone_info;
+
+			zone_info = &zinfo->zone_cache[zno + i];
+			if (!zone_info->len)
+				break;
+		}
+
+		if (i == *nr_zones) {
+			/* Cache hit on all the zones */
+			memcpy(zones, zinfo->zone_cache + zno,
+			       sizeof(*zinfo->zone_cache) * *nr_zones);
+			return 0;
+		}
+	}
+
 	ret = blkdev_report_zones(device->bdev, pos >> SECTOR_SHIFT, *nr_zones,
 				  copy_zone_info_cb, zones);
 	if (ret < 0) {
@@ -219,6 +251,11 @@
 	if (!ret)
 		return -EIO;
 
+	/* Populate cache */
+	if (zinfo->zone_cache)
+		memcpy(zinfo->zone_cache + zno, zones,
+		       sizeof(*zinfo->zone_cache) * *nr_zones);
+
 	return 0;
 }
 
@@ -282,7 +319,7 @@
 		if (!device->bdev)
 			continue;
 
-		ret = btrfs_get_dev_zone_info(device);
+		ret = btrfs_get_dev_zone_info(device, true);
 		if (ret)
 			break;
 	}
@@ -291,7 +328,7 @@
 	return ret;
 }
 
-int btrfs_get_dev_zone_info(struct btrfs_device *device)
+int btrfs_get_dev_zone_info(struct btrfs_device *device, bool populate_cache)
 {
 	struct btrfs_fs_info *fs_info = device->fs_info;
 	struct btrfs_zoned_device_info *zone_info = NULL;
@@ -318,6 +355,8 @@
 	if (!zone_info)
 		return -ENOMEM;
 
+	device->zone_info = zone_info;
+
 	if (!bdev_is_zoned(bdev)) {
 		if (!fs_info->zone_size) {
 			ret = calculate_emulated_zone_size(fs_info);
@@ -348,6 +387,25 @@
 	nr_sectors = bdev_nr_sectors(bdev);
 	zone_info->zone_size_shift = ilog2(zone_info->zone_size);
 	zone_info->nr_zones = nr_sectors >> ilog2(zone_sectors);
+	/*
+	 * We limit max_zone_append_size also by max_segments *
+	 * PAGE_SIZE. Technically, we can have multiple pages per segment. But,
+	 * since btrfs adds the pages one by one to a bio, and btrfs cannot
+	 * increase the metadata reservation even if it increases the number of
+	 * extents, it is safe to stick with the limit.
+	 *
+	 * With the zoned emulation, we can have non-zoned device on the zoned
+	 * mode. In this case, we don't have a valid max zone append size. So,
+	 * use max_segments * PAGE_SIZE as the pseudo max_zone_append_size.
+	 */
+	if (bdev_is_zoned(bdev)) {
+		zone_info->max_zone_append_size = min_t(u64,
+			(u64)bdev_max_zone_append_sectors(bdev) << SECTOR_SHIFT,
+			(u64)bdev_max_segments(bdev) << PAGE_SHIFT);
+	} else {
+		zone_info->max_zone_append_size =
+			(u64)bdev_max_segments(bdev) << PAGE_SHIFT;
+	}
 	if (!IS_ALIGNED(nr_sectors, zone_sectors))
 		zone_info->nr_zones++;
 
@@ -363,12 +421,29 @@
 		goto out;
 	}
 
-	zones = kcalloc(BTRFS_REPORT_NR_ZONES, sizeof(struct blk_zone), GFP_KERNEL);
+	zones = kvcalloc(BTRFS_REPORT_NR_ZONES, sizeof(struct blk_zone), GFP_KERNEL);
 	if (!zones) {
 		ret = -ENOMEM;
 		goto out;
 	}
 
+	/*
+	 * Enable zone cache only for a zoned device. On a non-zoned device, we
+	 * fill the zone info with emulated CONVENTIONAL zones, so no need to
+	 * use the cache.
+	 */
+	if (populate_cache && bdev_is_zoned(device->bdev)) {
+		zone_info->zone_cache = vzalloc(sizeof(struct blk_zone) *
+						zone_info->nr_zones);
+		if (!zone_info->zone_cache) {
+			btrfs_err_in_rcu(device->fs_info,
+				"zoned: failed to allocate zone cache for %s",
+				rcu_str_deref(device->name));
+			ret = -ENOMEM;
+			goto out;
+		}
+	}
+
 	/* Get zones type */
 	while (sector < nr_sectors) {
 		nr_zones = BTRFS_REPORT_NR_ZONES;
@@ -442,9 +517,7 @@
 	}
 
 
-	kfree(zones);
-
-	device->zone_info = zone_info;
+	kvfree(zones);
 
 	switch (bdev_zoned_model(bdev)) {
 	case BLK_ZONED_HM:
@@ -476,12 +549,9 @@
 	return 0;
 
 out:
-	kfree(zones);
+	kvfree(zones);
 out_free_zone_info:
-	bitmap_free(zone_info->empty_zones);
-	bitmap_free(zone_info->seq_zones);
-	kfree(zone_info);
-	device->zone_info = NULL;
+	btrfs_destroy_dev_zone_info(device);
 
 	return ret;
 }
@@ -495,6 +565,7 @@
 
 	bitmap_free(zone_info->seq_zones);
 	bitmap_free(zone_info->empty_zones);
+	vfree(zone_info->zone_cache);
 	kfree(zone_info);
 	device->zone_info = NULL;
 }
@@ -519,6 +590,7 @@
 	u64 zoned_devices = 0;
 	u64 nr_devices = 0;
 	u64 zone_size = 0;
+	u64 max_zone_append_size = 0;
 	const bool incompat_zoned = btrfs_fs_incompat(fs_info, ZONED);
 	int ret = 0;
 
@@ -554,6 +626,11 @@
 				ret = -EINVAL;
 				goto out;
 			}
+			if (!max_zone_append_size ||
+			    (zone_info->max_zone_append_size &&
+			     zone_info->max_zone_append_size < max_zone_append_size))
+				max_zone_append_size =
+					zone_info->max_zone_append_size;
 		}
 		nr_devices++;
 	}
@@ -585,7 +662,7 @@
 
 	/*
 	 * stripe_size is always aligned to BTRFS_STRIPE_LEN in
-	 * __btrfs_alloc_chunk(). Since we want stripe_len == zone_size,
+	 * btrfs_create_chunk(). Since we want stripe_len == zone_size,
 	 * check the alignment here.
 	 */
 	if (!IS_ALIGNED(zone_size, BTRFS_STRIPE_LEN)) {
@@ -603,7 +680,11 @@
 	}
 
 	fs_info->zone_size = zone_size;
+	fs_info->max_zone_append_size = ALIGN_DOWN(max_zone_append_size,
+						   fs_info->sectorsize);
 	fs_info->fs_devices->chunk_alloc_policy = BTRFS_CHUNK_ALLOC_ZONED;
+	if (fs_info->max_zone_append_size < fs_info->max_extent_size)
+		fs_info->max_extent_size = fs_info->max_zone_append_size;
 
 	/*
 	 * Check mount options here, because we might change fs_info->zoned
@@ -933,12 +1014,12 @@
 		return -ERANGE;
 
 	/* All the zones are conventional */
-	if (find_next_bit(zinfo->seq_zones, begin, end) == end)
+	if (find_next_bit(zinfo->seq_zones, end, begin) == end)
 		return 0;
 
 	/* All the zones are sequential and empty */
-	if (find_next_zero_bit(zinfo->seq_zones, begin, end) == end &&
-	    find_next_zero_bit(zinfo->empty_zones, begin, end) == end)
+	if (find_next_zero_bit(zinfo->seq_zones, end, begin) == end &&
+	    find_next_zero_bit(zinfo->empty_zones, end, begin) == end)
 		return 0;
 
 	for (pos = start; pos < start + size; pos += zinfo->zone_size) {
@@ -1075,10 +1156,12 @@
 		struct btrfs_dev_replace *dev_replace = &fs_info->dev_replace;
 		int dev_replace_is_ongoing = 0;
 
+		down_read(&dev_replace->rwsem);
 		device = map->stripes[i].dev;
 		physical = map->stripes[i].physical;
 
 		if (device->bdev == NULL) {
+			up_read(&dev_replace->rwsem);
 			alloc_offsets[i] = WP_MISSING_DEV;
 			continue;
 		}
@@ -1090,6 +1173,7 @@
 			num_conventional++;
 
 		if (!is_sequential) {
+			up_read(&dev_replace->rwsem);
 			alloc_offsets[i] = WP_CONVENTIONAL;
 			continue;
 		}
@@ -1100,11 +1184,9 @@
 		 */
 		btrfs_dev_clear_zone_empty(device, physical);
 
-		down_read(&dev_replace->rwsem);
 		dev_replace_is_ongoing = btrfs_dev_replace_is_ongoing(dev_replace);
 		if (dev_replace_is_ongoing && dev_replace->tgtdev != NULL)
 			btrfs_dev_clear_zone_empty(dev_replace->tgtdev, physical);
-		up_read(&dev_replace->rwsem);
 
 		/*
 		 * The group is mapped to a sequential zone. Get the zone write
@@ -1115,6 +1197,7 @@
 		ret = btrfs_get_dev_zone(device, physical, &zone);
 		memalloc_nofs_restore(nofs_flag);
 		if (ret == -EIO || ret == -EOPNOTSUPP) {
+			up_read(&dev_replace->rwsem);
 			ret = 0;
 			alloc_offsets[i] = WP_MISSING_DEV;
 			continue;
@@ -1127,6 +1210,7 @@
 	"zoned: unexpected conventional zone %llu on device %s (devid %llu)",
 				zone.start << SECTOR_SHIFT,
 				rcu_str_deref(device->name), device->devid);
+			up_read(&dev_replace->rwsem);
 			ret = -EIO;
 			goto out;
 		}
@@ -1152,6 +1236,8 @@
 					((zone.wp - zone.start) << SECTOR_SHIFT);
 			break;
 		}
+
+		up_read(&dev_replace->rwsem);
 	}
 
 	if (num_sequential > 0)
@@ -1266,11 +1352,11 @@
 	    !list_empty(&eb->release_list))
 		return;
 
+	memzero_extent_buffer(eb, 0, eb->len);
+	set_bit(EXTENT_BUFFER_NO_CHECK, &eb->bflags);
 	set_extent_buffer_dirty(eb);
 	set_extent_bits_nowait(&trans->dirty_pages, eb->start,
 			       eb->start + eb->len - 1, EXTENT_DIRTY);
-	memzero_extent_buffer(eb, 0, eb->len);
-	set_bit(EXTENT_BUFFER_NO_CHECK, &eb->bflags);
 
 	spin_lock(&trans->releasing_ebs_lock);
 	list_add_tail(&eb->release_list, &trans->releasing_ebs);
@@ -1304,6 +1390,17 @@
 	if (!is_data_inode(&inode->vfs_inode))
 		return false;
 
+	/*
+	 * Using REQ_OP_ZONE_APPNED for relocation can break assumptions on the
+	 * extent layout the relocation code has.
+	 * Furthermore we have set aside own block-group from which only the
+	 * relocation "process" can allocate and make sure only one process at a
+	 * time can add pages to an extent that gets relocated, so it's safe to
+	 * use regular REQ_OP_WRITE for this special case.
+	 */
+	if (btrfs_is_data_reloc_root(inode->root))
+		return false;
+
 	cache = btrfs_lookup_block_group(fs_info, start);
 	ASSERT(cache);
 	if (!cache)
@@ -1440,27 +1537,29 @@
 static int read_zone_info(struct btrfs_fs_info *fs_info, u64 logical,
 			  struct blk_zone *zone)
 {
-	struct btrfs_bio *bbio = NULL;
+	struct btrfs_io_context *bioc = NULL;
 	u64 mapped_length = PAGE_SIZE;
 	unsigned int nofs_flag;
 	int nmirrors;
 	int i, ret;
 
 	ret = btrfs_map_sblock(fs_info, BTRFS_MAP_GET_READ_MIRRORS, logical,
-			       &mapped_length, &bbio);
-	if (ret || !bbio || mapped_length < PAGE_SIZE) {
-		btrfs_put_bbio(bbio);
-		return -EIO;
+			       &mapped_length, &bioc);
+	if (ret || !bioc || mapped_length < PAGE_SIZE) {
+		ret = -EIO;
+		goto out_put_bioc;
 	}
 
-	if (bbio->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK)
-		return -EINVAL;
+	if (bioc->map_type & BTRFS_BLOCK_GROUP_RAID56_MASK) {
+		ret = -EINVAL;
+		goto out_put_bioc;
+	}
 
 	nofs_flag = memalloc_nofs_save();
-	nmirrors = (int)bbio->num_stripes;
+	nmirrors = (int)bioc->num_stripes;
 	for (i = 0; i < nmirrors; i++) {
-		u64 physical = bbio->stripes[i].physical;
-		struct btrfs_device *dev = bbio->stripes[i].dev;
+		u64 physical = bioc->stripes[i].physical;
+		struct btrfs_device *dev = bioc->stripes[i].dev;
 
 		/* Missing device */
 		if (!dev->bdev)
@@ -1473,7 +1572,8 @@
 		break;
 	}
 	memalloc_nofs_restore(nofs_flag);
-
+out_put_bioc:
+	btrfs_put_bioc(bioc);
 	return ret;
 }
 
@@ -1530,3 +1630,58 @@
 
 	return device;
 }
+
+void btrfs_clear_data_reloc_bg(struct btrfs_block_group *bg)
+{
+	struct btrfs_fs_info *fs_info = bg->fs_info;
+
+	spin_lock(&fs_info->relocation_bg_lock);
+	if (fs_info->data_reloc_bg == bg->start)
+		fs_info->data_reloc_bg = 0;
+	spin_unlock(&fs_info->relocation_bg_lock);
+}
+
+void btrfs_free_zone_cache(struct btrfs_fs_info *fs_info)
+{
+	struct btrfs_fs_devices *fs_devices = fs_info->fs_devices;
+	struct btrfs_device *device;
+
+	if (!btrfs_is_zoned(fs_info))
+		return;
+
+	mutex_lock(&fs_devices->device_list_mutex);
+	list_for_each_entry(device, &fs_devices->devices, dev_list) {
+		if (device->zone_info) {
+			vfree(device->zone_info->zone_cache);
+			device->zone_info->zone_cache = NULL;
+		}
+	}
+	mutex_unlock(&fs_devices->device_list_mutex);
+}
+
+void btrfs_zoned_release_data_reloc_bg(struct btrfs_fs_info *fs_info, u64 logical,
+				       u64 length)
+{
+	struct btrfs_block_group *block_group;
+
+	if (!btrfs_is_zoned(fs_info))
+		return;
+
+	block_group = btrfs_lookup_block_group(fs_info, logical);
+	/* It should be called on a previous data relocation block group. */
+	ASSERT(block_group && (block_group->flags & BTRFS_BLOCK_GROUP_DATA));
+
+	spin_lock(&block_group->lock);
+	if (!block_group->zoned_data_reloc_ongoing)
+		goto out;
+
+	/* All relocation extents are written. */
+	if (block_group->start + block_group->alloc_offset == logical + length) {
+		/* Now, release this block group for further allocations. */
+		block_group->zoned_data_reloc_ongoing = 0;
+	}
+
+out:
+	spin_unlock(&block_group->lock);
+	btrfs_put_block_group(block_group);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/btrfs/zoned.h
+++ linux-xilinx-zynqmp-5.15.0/fs/btrfs/zoned.h
@@ -8,6 +8,7 @@
 #include "volumes.h"
 #include "disk-io.h"
 #include "block-group.h"
+#include "btrfs_inode.h"
 
 /*
  * Block groups with more than this value (percents) of unusable space will be
@@ -22,9 +23,11 @@
 	 */
 	u64 zone_size;
 	u8  zone_size_shift;
+	u64 max_zone_append_size;
 	u32 nr_zones;
 	unsigned long *seq_zones;
 	unsigned long *empty_zones;
+	struct blk_zone *zone_cache;
 	struct blk_zone sb_zones[2 * BTRFS_SUPER_MIRROR_MAX];
 };
 
@@ -32,7 +35,7 @@
 int btrfs_get_dev_zone(struct btrfs_device *device, u64 pos,
 		       struct blk_zone *zone);
 int btrfs_get_dev_zone_info_all_devices(struct btrfs_fs_info *fs_info);
-int btrfs_get_dev_zone_info(struct btrfs_device *device);
+int btrfs_get_dev_zone_info(struct btrfs_device *device, bool populate_cache);
 void btrfs_destroy_dev_zone_info(struct btrfs_device *device);
 int btrfs_check_zoned_mode(struct btrfs_fs_info *fs_info);
 int btrfs_check_mountopts_zoned(struct btrfs_fs_info *info);
@@ -66,6 +69,10 @@
 				  u64 physical_start, u64 physical_pos);
 struct btrfs_device *btrfs_zoned_get_device(struct btrfs_fs_info *fs_info,
 					    u64 logical, u64 length);
+void btrfs_clear_data_reloc_bg(struct btrfs_block_group *bg);
+void btrfs_free_zone_cache(struct btrfs_fs_info *fs_info);
+void btrfs_zoned_release_data_reloc_bg(struct btrfs_fs_info *fs_info, u64 logical,
+				       u64 length);
 #else /* CONFIG_BLK_DEV_ZONED */
 static inline int btrfs_get_dev_zone(struct btrfs_device *device, u64 pos,
 				     struct blk_zone *zone)
@@ -78,7 +85,8 @@
 	return 0;
 }
 
-static inline int btrfs_get_dev_zone_info(struct btrfs_device *device)
+static inline int btrfs_get_dev_zone_info(struct btrfs_device *device,
+					  bool populate_cache)
 {
 	return 0;
 }
@@ -199,6 +207,12 @@
 	return ERR_PTR(-EOPNOTSUPP);
 }
 
+static inline void btrfs_clear_data_reloc_bg(struct btrfs_block_group *bg) { }
+
+static inline void btrfs_free_zone_cache(struct btrfs_fs_info *fs_info) { }
+
+static inline void btrfs_zoned_release_data_reloc_bg(struct btrfs_fs_info *fs_info,
+						     u64 logical, u64 length) { }
 #endif
 
 static inline bool btrfs_dev_is_sequential(struct btrfs_device *device, u64 pos)
@@ -317,4 +331,20 @@
 	spin_unlock(&fs_info->treelog_bg_lock);
 }
 
+static inline void btrfs_zoned_data_reloc_lock(struct btrfs_inode *inode)
+{
+	struct btrfs_root *root = inode->root;
+
+	if (btrfs_is_data_reloc_root(root) && btrfs_is_zoned(root->fs_info))
+		mutex_lock(&root->fs_info->zoned_data_reloc_io_lock);
+}
+
+static inline void btrfs_zoned_data_reloc_unlock(struct btrfs_inode *inode)
+{
+	struct btrfs_root *root = inode->root;
+
+	if (btrfs_is_data_reloc_root(root) && btrfs_is_zoned(root->fs_info))
+		mutex_unlock(&root->fs_info->zoned_data_reloc_io_lock);
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/buffer.c
+++ linux-xilinx-zynqmp-5.15.0/fs/buffer.c
@@ -1235,16 +1235,18 @@
 	int i;
 
 	check_irqs_on();
+	bh_lru_lock();
+
 	/*
 	 * the refcount of buffer_head in bh_lru prevents dropping the
 	 * attached page(i.e., try_to_free_buffers) so it could cause
 	 * failing page migration.
 	 * Skip putting upcoming bh into bh_lru until migration is done.
 	 */
-	if (lru_cache_disabled())
+	if (lru_cache_disabled()) {
+		bh_lru_unlock();
 		return;
-
-	bh_lru_lock();
+	}
 
 	b = this_cpu_ptr(&bh_lrus);
 	for (i = 0; i < BH_LRU_SIZE; i++) {
@@ -2350,7 +2352,7 @@
 {
 	struct address_space *mapping = inode->i_mapping;
 	struct page *page;
-	void *fsdata;
+	void *fsdata = NULL;
 	int err;
 
 	err = inode_newsize_ok(inode, size);
@@ -2376,7 +2378,7 @@
 	struct inode *inode = mapping->host;
 	unsigned int blocksize = i_blocksize(inode);
 	struct page *page;
-	void *fsdata;
+	void *fsdata = NULL;
 	pgoff_t index, curidx;
 	loff_t curpos;
 	unsigned zerofrom, offset, len;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cachefiles/bind.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cachefiles/bind.c
@@ -117,7 +117,7 @@
 	root = path.dentry;
 
 	ret = -EINVAL;
-	if (mnt_user_ns(path.mnt) != &init_user_ns) {
+	if (is_idmapped_mnt(path.mnt)) {
 		pr_warn("File cache on idmapped mounts not supported");
 		goto error_unsupported;
 	}
@@ -249,6 +249,8 @@
 	kmem_cache_free(cachefiles_object_jar, fsdef);
 error_root_object:
 	cachefiles_end_secure(cache, saved_cred);
+	put_cred(cache->cache_cred);
+	cache->cache_cred = NULL;
 	pr_err("Failed to register: %d\n", ret);
 	return ret;
 }
@@ -269,6 +271,7 @@
 
 	dput(cache->graveyard);
 	mntput(cache->mnt);
+	put_cred(cache->cache_cred);
 
 	kfree(cache->rootdirname);
 	kfree(cache->secctx);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/addr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/addr.c
@@ -95,7 +95,6 @@
 
 	/* dirty the head */
 	spin_lock(&ci->i_ceph_lock);
-	BUG_ON(ci->i_wr_ref == 0); // caller should hold Fw reference
 	if (__ceph_have_pending_cap_snap(ci)) {
 		struct ceph_cap_snap *capsnap =
 				list_last_entry(&ci->i_cap_snaps,
@@ -179,7 +178,7 @@
 
 static void ceph_netfs_expand_readahead(struct netfs_read_request *rreq)
 {
-	struct inode *inode = rreq->mapping->host;
+	struct inode *inode = rreq->inode;
 	struct ceph_inode_info *ci = ceph_inode(inode);
 	struct ceph_file_layout *lo = &ci->i_layout;
 	u32 blockoff;
@@ -196,7 +195,7 @@
 
 static bool ceph_netfs_clamp_length(struct netfs_read_subrequest *subreq)
 {
-	struct inode *inode = subreq->rreq->mapping->host;
+	struct inode *inode = subreq->rreq->inode;
 	struct ceph_fs_client *fsc = ceph_inode_to_client(inode);
 	struct ceph_inode_info *ci = ceph_inode(inode);
 	u64 objno, objoff;
@@ -242,7 +241,7 @@
 static void ceph_netfs_issue_op(struct netfs_read_subrequest *subreq)
 {
 	struct netfs_read_request *rreq = subreq->rreq;
-	struct inode *inode = rreq->mapping->host;
+	struct inode *inode = rreq->inode;
 	struct ceph_inode_info *ci = ceph_inode(inode);
 	struct ceph_fs_client *fsc = ceph_inode_to_client(inode);
 	struct ceph_osd_request *req;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/caps.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/caps.c
@@ -1390,7 +1390,7 @@
 	if (flushing & CEPH_CAP_XATTR_EXCL) {
 		arg->old_xattr_buf = __ceph_build_xattrs_blob(ci);
 		arg->xattr_version = ci->i_xattrs.version;
-		arg->xattr_buf = ci->i_xattrs.blob;
+		arg->xattr_buf = ceph_buffer_get(ci->i_xattrs.blob);
 	} else {
 		arg->xattr_buf = NULL;
 		arg->old_xattr_buf = NULL;
@@ -1456,6 +1456,7 @@
 	encode_cap_msg(msg, arg);
 	ceph_con_send(&arg->session->s_con, msg);
 	ceph_buffer_put(arg->old_xattr_buf);
+	ceph_buffer_put(arg->xattr_buf);
 	if (arg->wake)
 		wake_up_all(&ci->i_cap_wq);
 }
@@ -1624,6 +1625,7 @@
 	struct inode *inode = &ci->vfs_inode;
 	struct ceph_mds_client *mdsc = ceph_inode_to_client(inode)->mdsc;
 	struct ceph_mds_session *session = NULL;
+	bool need_put = false;
 	int mds;
 
 	dout("ceph_flush_snaps %p\n", inode);
@@ -1668,8 +1670,13 @@
 		ceph_put_mds_session(session);
 	/* we flushed them all; remove this inode from the queue */
 	spin_lock(&mdsc->snap_flush_lock);
+	if (!list_empty(&ci->i_snap_flush_item))
+		need_put = true;
 	list_del_init(&ci->i_snap_flush_item);
 	spin_unlock(&mdsc->snap_flush_lock);
+
+	if (need_put)
+		iput(inode);
 }
 
 /*
@@ -2240,33 +2247,29 @@
 	 * to wait the journal logs to be flushed by the MDSes periodically.
 	 */
 	if (req1 || req2) {
-		struct ceph_mds_session **sessions = NULL;
-		struct ceph_mds_session *s;
 		struct ceph_mds_request *req;
-		unsigned int max;
+		struct ceph_mds_session **sessions;
+		struct ceph_mds_session *s;
+		unsigned int max_sessions;
 		int i;
 
-		/*
-		 * The mdsc->max_sessions is unlikely to be changed
-		 * mostly, here we will retry it by reallocating the
-		 * sessions arrary memory to get rid of the mdsc->mutex
-		 * lock.
-		 */
-retry:
-		max = mdsc->max_sessions;
-		sessions = krealloc(sessions, max * sizeof(s), __GFP_ZERO);
-		if (!sessions)
-			return -ENOMEM;
+		mutex_lock(&mdsc->mutex);
+		max_sessions = mdsc->max_sessions;
+
+		sessions = kcalloc(max_sessions, sizeof(s), GFP_KERNEL);
+		if (!sessions) {
+			mutex_unlock(&mdsc->mutex);
+			err = -ENOMEM;
+			goto out;
+		}
 
 		spin_lock(&ci->i_unsafe_lock);
 		if (req1) {
 			list_for_each_entry(req, &ci->i_unsafe_dirops,
 					    r_unsafe_dir_item) {
 				s = req->r_session;
-				if (unlikely(s->s_mds >= max)) {
-					spin_unlock(&ci->i_unsafe_lock);
-					goto retry;
-				}
+				if (!s)
+					continue;
 				if (!sessions[s->s_mds]) {
 					s = ceph_get_mds_session(s);
 					sessions[s->s_mds] = s;
@@ -2277,10 +2280,8 @@
 			list_for_each_entry(req, &ci->i_unsafe_iops,
 					    r_unsafe_target_item) {
 				s = req->r_session;
-				if (unlikely(s->s_mds >= max)) {
-					spin_unlock(&ci->i_unsafe_lock);
-					goto retry;
-				}
+				if (!s)
+					continue;
 				if (!sessions[s->s_mds]) {
 					s = ceph_get_mds_session(s);
 					sessions[s->s_mds] = s;
@@ -2292,14 +2293,15 @@
 		/* the auth MDS */
 		spin_lock(&ci->i_ceph_lock);
 		if (ci->i_auth_cap) {
-		      s = ci->i_auth_cap->session;
-		      if (!sessions[s->s_mds])
-			      sessions[s->s_mds] = ceph_get_mds_session(s);
+			s = ci->i_auth_cap->session;
+			if (!sessions[s->s_mds])
+				sessions[s->s_mds] = ceph_get_mds_session(s);
 		}
 		spin_unlock(&ci->i_ceph_lock);
+		mutex_unlock(&mdsc->mutex);
 
 		/* send flush mdlog request to MDSes */
-		for (i = 0; i < max; i++) {
+		for (i = 0; i < max_sessions; i++) {
 			s = sessions[i];
 			if (s) {
 				send_flush_mdlog(s);
@@ -2316,15 +2318,19 @@
 					ceph_timeout_jiffies(req1->r_timeout));
 		if (ret)
 			err = -EIO;
-		ceph_mdsc_put_request(req1);
 	}
 	if (req2) {
 		ret = !wait_for_completion_timeout(&req2->r_safe_completion,
 					ceph_timeout_jiffies(req2->r_timeout));
 		if (ret)
 			err = -EIO;
-		ceph_mdsc_put_request(req2);
 	}
+
+out:
+	if (req1)
+		ceph_mdsc_put_request(req1);
+	if (req2)
+		ceph_mdsc_put_request(req2);
 	return err;
 }
 
@@ -2873,7 +2879,7 @@
 
 	while (true) {
 		flags &= CEPH_FILE_MODE_MASK;
-		if (atomic_read(&fi->num_locks))
+		if (vfs_inode_has_locks(inode))
 			flags |= CHECK_FILELOCK;
 		_got = 0;
 		ret = try_get_cap_refs(inode, need, want, endoff,
@@ -3512,6 +3518,15 @@
 	}
 	BUG_ON(cap->issued & ~cap->implemented);
 
+	/* don't let check_caps skip sending a response to MDS for revoke msgs */
+	if (le32_to_cpu(grant->op) == CEPH_CAP_OP_REVOKE) {
+		cap->mds_wanted = 0;
+		if (cap == ci->i_auth_cap)
+			check_caps = 1; /* check auth cap only */
+		else
+			check_caps = 2; /* check all caps */
+	}
+
 	if (extra_info->inline_version > 0 &&
 	    extra_info->inline_version >= ci->i_inline_version) {
 		ci->i_inline_version = extra_info->inline_version;
@@ -3520,24 +3535,23 @@
 			fill_inline = true;
 	}
 
-	if (ci->i_auth_cap == cap &&
-	    le32_to_cpu(grant->op) == CEPH_CAP_OP_IMPORT) {
-		if (newcaps & ~extra_info->issued)
-			wake = true;
+	if (le32_to_cpu(grant->op) == CEPH_CAP_OP_IMPORT) {
+		if (ci->i_auth_cap == cap) {
+			if (newcaps & ~extra_info->issued)
+				wake = true;
+
+			if (ci->i_requested_max_size > max_size ||
+			    !(le32_to_cpu(grant->wanted) & CEPH_CAP_ANY_FILE_WR)) {
+				/* re-request max_size if necessary */
+				ci->i_requested_max_size = 0;
+				wake = true;
+			}
 
-		if (ci->i_requested_max_size > max_size ||
-		    !(le32_to_cpu(grant->wanted) & CEPH_CAP_ANY_FILE_WR)) {
-			/* re-request max_size if necessary */
-			ci->i_requested_max_size = 0;
-			wake = true;
+			ceph_kick_flushing_inode_caps(session, ci);
 		}
-
-		ceph_kick_flushing_inode_caps(session, ci);
-		spin_unlock(&ci->i_ceph_lock);
 		up_read(&session->s_mdsc->snap_rwsem);
-	} else {
-		spin_unlock(&ci->i_ceph_lock);
 	}
+	spin_unlock(&ci->i_ceph_lock);
 
 	if (fill_inline)
 		ceph_fill_inline_data(inode, NULL, extra_info->inline_data,
@@ -4349,7 +4363,7 @@
 {
 	struct ceph_mds_client *mdsc = ceph_sb_to_mdsc(ci->vfs_inode.i_sb);
 	int bits = (fmode << 1) | 1;
-	bool is_opened = false;
+	bool already_opened = false;
 	int i;
 
 	if (count == 1)
@@ -4357,19 +4371,19 @@
 
 	spin_lock(&ci->i_ceph_lock);
 	for (i = 0; i < CEPH_FILE_MODE_BITS; i++) {
-		if (bits & (1 << i))
-			ci->i_nr_by_mode[i] += count;
-
 		/*
-		 * If any of the mode ref is larger than 1,
+		 * If any of the mode ref is larger than 0,
 		 * that means it has been already opened by
 		 * others. Just skip checking the PIN ref.
 		 */
-		if (i && ci->i_nr_by_mode[i] > 1)
-			is_opened = true;
+		if (i && ci->i_nr_by_mode[i])
+			already_opened = true;
+
+		if (bits & (1 << i))
+			ci->i_nr_by_mode[i] += count;
 	}
 
-	if (!is_opened)
+	if (!already_opened)
 		percpu_counter_inc(&mdsc->metric.opened_inodes);
 	spin_unlock(&ci->i_ceph_lock);
 }
@@ -4523,12 +4537,14 @@
 			       struct inode *dir,
 			       int mds, int drop, int unless)
 {
-	struct dentry *parent = NULL;
 	struct ceph_mds_request_release *rel = *p;
 	struct ceph_dentry_info *di = ceph_dentry(dentry);
 	int force = 0;
 	int ret;
 
+	/* This shouldn't happen */
+	BUG_ON(!dir);
+
 	/*
 	 * force an record for the directory caps if we have a dentry lease.
 	 * this is racy (can't take i_ceph_lock and d_lock together), but it
@@ -4538,14 +4554,9 @@
 	spin_lock(&dentry->d_lock);
 	if (di->lease_session && di->lease_session->s_mds == mds)
 		force = 1;
-	if (!dir) {
-		parent = dget(dentry->d_parent);
-		dir = d_inode(parent);
-	}
 	spin_unlock(&dentry->d_lock);
 
 	ret = ceph_encode_inode_release(p, dir, mds, drop, unless, force);
-	dput(parent);
 
 	spin_lock(&dentry->d_lock);
 	if (ret && di->lease_session && di->lease_session->s_mds == mds) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/dir.c
@@ -478,8 +478,11 @@
 					2 : (fpos_off(rde->offset) + 1);
 			err = note_last_dentry(dfi, rde->name, rde->name_len,
 					       next_offset);
-			if (err)
+			if (err) {
+				ceph_mdsc_put_request(dfi->last_readdir);
+				dfi->last_readdir = NULL;
 				return err;
+			}
 		} else if (req->r_reply_info.dir_end) {
 			dfi->next_offset = 2;
 			/* keep last name */
@@ -520,6 +523,12 @@
 		if (!dir_emit(ctx, rde->name, rde->name_len,
 			      ceph_present_ino(inode->i_sb, le64_to_cpu(rde->inode.in->ino)),
 			      le32_to_cpu(rde->inode.in->mode) >> 12)) {
+			/*
+			 * NOTE: Here no need to put the 'dfi->last_readdir',
+			 * because when dir_emit stops us it's most likely
+			 * doesn't have enough memory, etc. So for next readdir
+			 * it will continue.
+			 */
 			dout("filldir stopping us...\n");
 			return 0;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/file.c
@@ -577,6 +577,7 @@
 	struct ceph_inode_info *ci = ceph_inode(dir);
 	struct inode *inode;
 	struct timespec64 now;
+	struct ceph_string *pool_ns;
 	struct ceph_mds_client *mdsc = ceph_sb_to_mdsc(dir->i_sb);
 	struct ceph_vino vino = { .ino = req->r_deleg_ino,
 				  .snap = CEPH_NOSNAP };
@@ -591,9 +592,15 @@
 	iinfo.change_attr = 1;
 	ceph_encode_timespec64(&iinfo.btime, &now);
 
-	iinfo.xattr_len = ARRAY_SIZE(xattr_buf);
-	iinfo.xattr_data = xattr_buf;
-	memset(iinfo.xattr_data, 0, iinfo.xattr_len);
+	if (req->r_pagelist) {
+		iinfo.xattr_len = req->r_pagelist->length;
+		iinfo.xattr_data = req->r_pagelist->mapped_tail;
+	} else {
+		/* fake it */
+		iinfo.xattr_len = ARRAY_SIZE(xattr_buf);
+		iinfo.xattr_data = xattr_buf;
+		memset(iinfo.xattr_data, 0, iinfo.xattr_len);
+	}
 
 	in.ino = cpu_to_le64(vino.ino);
 	in.snapid = cpu_to_le64(CEPH_NOSNAP);
@@ -603,17 +610,35 @@
 	in.cap.realm = cpu_to_le64(ci->i_snap_realm->ino);
 	in.cap.flags = CEPH_CAP_FLAG_AUTH;
 	in.ctime = in.mtime = in.atime = iinfo.btime;
-	in.mode = cpu_to_le32((u32)mode);
 	in.truncate_seq = cpu_to_le32(1);
 	in.truncate_size = cpu_to_le64(-1ULL);
 	in.xattr_version = cpu_to_le64(1);
 	in.uid = cpu_to_le32(from_kuid(&init_user_ns, current_fsuid()));
-	in.gid = cpu_to_le32(from_kgid(&init_user_ns, dir->i_mode & S_ISGID ?
-				dir->i_gid : current_fsgid()));
+	if (dir->i_mode & S_ISGID) {
+		in.gid = cpu_to_le32(from_kgid(&init_user_ns, dir->i_gid));
+
+		/* Directories always inherit the setgid bit. */
+		if (S_ISDIR(mode))
+			mode |= S_ISGID;
+		else if ((mode & (S_ISGID | S_IXGRP)) == (S_ISGID | S_IXGRP) &&
+			 !in_group_p(dir->i_gid) &&
+			 !capable_wrt_inode_uidgid(&init_user_ns, dir, CAP_FSETID))
+			mode &= ~S_ISGID;
+	} else {
+		in.gid = cpu_to_le32(from_kgid(&init_user_ns, current_fsgid()));
+	}
+	in.mode = cpu_to_le32((u32)mode);
+
 	in.nlink = cpu_to_le32(1);
 	in.max_size = cpu_to_le64(lo->stripe_unit);
 
 	ceph_file_layout_to_legacy(lo, &in.layout);
+	/* lo is private, so pool_ns can't change */
+	pool_ns = rcu_dereference_raw(lo->pool_ns);
+	if (pool_ns) {
+		iinfo.pool_ns_len = pool_ns->len;
+		iinfo.pool_ns_data = pool_ns->str;
+	}
 
 	down_read(&mdsc->snap_rwsem);
 	ret = ceph_fill_inode(inode, NULL, &iinfo, NULL, req->r_session,
@@ -678,6 +703,12 @@
 	if (dentry->d_name.len > NAME_MAX)
 		return -ENAMETOOLONG;
 
+	/*
+	 * Do not truncate the file, since atomic_open is called before the
+	 * permission check. The caller will do the truncation afterward.
+	 */
+	flags &= ~O_TRUNC;
+
 	if (flags & O_CREAT) {
 		if (ceph_quota_is_max_files_exceeded(dir))
 			return -EDQUOT;
@@ -687,6 +718,10 @@
 		err = ceph_security_init_secctx(dentry, mode, &as_ctx);
 		if (err < 0)
 			goto out_ctx;
+		/* Async create can't handle more than a page of xattrs */
+		if (as_ctx.pagelist &&
+		    !list_is_singular(&as_ctx.pagelist->head))
+			try_async = false;
 	} else if (!d_in_lookup(dentry)) {
 		/* If it's not being looked up, it's negative */
 		return -ENOENT;
@@ -732,16 +767,16 @@
 				restore_deleg_ino(dir, req->r_deleg_ino);
 				ceph_mdsc_put_request(req);
 				try_async = false;
+				ceph_put_string(rcu_dereference_raw(lo.pool_ns));
 				goto retry;
 			}
+			ceph_put_string(rcu_dereference_raw(lo.pool_ns));
 			goto out_req;
 		}
 	}
 
 	set_bit(CEPH_MDS_R_PARENT_LOCKED, &req->r_req_flags);
-	err = ceph_mdsc_do_request(mdsc,
-				   (flags & (O_CREAT|O_TRUNC)) ? dir : NULL,
-				   req);
+	err = ceph_mdsc_do_request(mdsc, (flags & O_CREAT) ? dir : NULL, req);
 	if (err == -ENOENT) {
 		dentry = ceph_handle_snapdir(req, dentry);
 		if (IS_ERR(dentry)) {
@@ -2049,6 +2084,9 @@
 	loff_t endoff = 0;
 	loff_t size;
 
+	dout("%s %p %llx.%llx mode %x, offset %llu length %llu\n", __func__,
+	     inode, ceph_vinop(inode), mode, offset, length);
+
 	if (mode != (FALLOC_FL_KEEP_SIZE | FALLOC_FL_PUNCH_HOLE))
 		return -EOPNOTSUPP;
 
@@ -2089,6 +2127,10 @@
 	if (ret < 0)
 		goto unlock;
 
+	ret = file_modified(file);
+	if (ret)
+		goto put_caps;
+
 	filemap_invalidate_lock(inode->i_mapping);
 	ceph_zero_pagecache_range(inode, offset, length);
 	ret = ceph_zero_objects(inode, offset, length);
@@ -2104,6 +2146,7 @@
 	}
 	filemap_invalidate_unlock(inode->i_mapping);
 
+put_caps:
 	ceph_put_cap_refs(ci, got);
 unlock:
 	inode_unlock(inode);
@@ -2393,7 +2436,7 @@
 		ret = do_splice_direct(src_file, &src_off, dst_file,
 				       &dst_off, src_objlen, flags);
 		/* Abort on short copies or on error */
-		if (ret < src_objlen) {
+		if (ret < (long)src_objlen) {
 			dout("Failed partial copy (%zd)\n", ret);
 			goto out;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/inode.c
@@ -87,13 +87,13 @@
 	if (!S_ISDIR(parent->i_mode)) {
 		pr_warn_once("bad snapdir parent type (mode=0%o)\n",
 			     parent->i_mode);
-		return ERR_PTR(-ENOTDIR);
+		goto err;
 	}
 
 	if (!(inode->i_state & I_NEW) && !S_ISDIR(inode->i_mode)) {
 		pr_warn_once("bad snapdir inode type (mode=0%o)\n",
 			     inode->i_mode);
-		return ERR_PTR(-ENOTDIR);
+		goto err;
 	}
 
 	inode->i_mode = parent->i_mode;
@@ -113,6 +113,12 @@
 	}
 
 	return inode;
+err:
+	if ((inode->i_state & I_NEW))
+		discard_new_inode(inode);
+	else
+		iput(inode);
+	return ERR_PTR(-ENOTDIR);
 }
 
 const struct inode_operations ceph_file_iops = {
@@ -641,9 +647,7 @@
 			ci->i_truncate_seq = truncate_seq;
 
 			/* the MDS should have revoked these caps */
-			WARN_ON_ONCE(issued & (CEPH_CAP_FILE_EXCL |
-					       CEPH_CAP_FILE_RD |
-					       CEPH_CAP_FILE_WR |
+			WARN_ON_ONCE(issued & (CEPH_CAP_FILE_RD |
 					       CEPH_CAP_FILE_LAZYIO));
 			/*
 			 * If we hold relevant caps, or in the case where we're
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/locks.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/locks.c
@@ -32,18 +32,14 @@
 
 static void ceph_fl_copy_lock(struct file_lock *dst, struct file_lock *src)
 {
-	struct ceph_file_info *fi = dst->fl_file->private_data;
 	struct inode *inode = file_inode(dst->fl_file);
 	atomic_inc(&ceph_inode(inode)->i_filelock_ref);
-	atomic_inc(&fi->num_locks);
 }
 
 static void ceph_fl_release_lock(struct file_lock *fl)
 {
-	struct ceph_file_info *fi = fl->fl_file->private_data;
 	struct inode *inode = file_inode(fl->fl_file);
 	struct ceph_inode_info *ci = ceph_inode(inode);
-	atomic_dec(&fi->num_locks);
 	if (atomic_dec_and_test(&ci->i_filelock_ref)) {
 		/* clear error when all locks are released */
 		spin_lock(&ci->i_ceph_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/mds_client.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/mds_client.c
@@ -1196,14 +1196,17 @@
 	if (count > 0) {
 		size_t i;
 		size_t size = FEATURE_BYTES(count);
+		unsigned long bit;
 
 		if (WARN_ON_ONCE(*p + 4 + size > end))
 			return -ERANGE;
 
 		ceph_encode_32(p, size);
 		memset(*p, 0, size);
-		for (i = 0; i < count; i++)
-			((unsigned char*)(*p))[i / 8] |= BIT(feature_bits[i] % 8);
+		for (i = 0; i < count; i++) {
+			bit = feature_bits[i];
+			((unsigned char *)(*p))[bit / 8] |= BIT(bit % 8);
+		}
 		*p += size;
 	} else {
 		if (WARN_ON_ONCE(*p + 4 > end))
@@ -2429,12 +2432,11 @@
 
 	if (pos < 0) {
 		/*
-		 * A rename didn't occur, but somehow we didn't end up where
-		 * we thought we would. Throw a warning and try again.
+		 * The path is longer than PATH_MAX and this function
+		 * cannot ever succeed.  Creating paths that long is
+		 * possible with Ceph, but Linux cannot use them.
 		 */
-		pr_warn("build_path did not end path lookup where "
-			"expected, pos is %d\n", pos);
-		goto retry;
+		return ERR_PTR(-ENAMETOOLONG);
 	}
 
 	*pbase = base;
@@ -3540,6 +3542,12 @@
 		break;
 
 	case CEPH_SESSION_FLUSHMSG:
+		/* flush cap releases */
+		spin_lock(&session->s_cap_lock);
+		if (session->s_num_cap_releases)
+			ceph_flush_cap_releases(mdsc, session);
+		spin_unlock(&session->s_cap_lock);
+
 		send_flushmsg_ack(mdsc, session, seq);
 		break;
 
@@ -3772,7 +3780,7 @@
 	struct ceph_pagelist *pagelist = recon_state->pagelist;
 	struct dentry *dentry;
 	char *path;
-	int pathlen, err;
+	int pathlen = 0, err;
 	u64 pathbase;
 	u64 snap_follows;
 
@@ -3792,7 +3800,6 @@
 		}
 	} else {
 		path = NULL;
-		pathlen = 0;
 		pathbase = 0;
 	}
 
@@ -4599,7 +4606,7 @@
 
 	dout("mdsc delayed_work\n");
 
-	if (mdsc->stopping)
+	if (mdsc->stopping >= CEPH_MDSC_STOPPING_FLUSHED)
 		return;
 
 	mutex_lock(&mdsc->mutex);
@@ -4778,7 +4785,7 @@
 void ceph_mdsc_pre_umount(struct ceph_mds_client *mdsc)
 {
 	dout("pre_umount\n");
-	mdsc->stopping = 1;
+	mdsc->stopping = CEPH_MDSC_STOPPING_BEGIN;
 
 	ceph_mdsc_iterate_sessions(mdsc, send_flush_mdlog, true);
 	ceph_mdsc_iterate_sessions(mdsc, lock_unlock_session, false);
@@ -4795,15 +4802,17 @@
 }
 
 /*
- * wait for all write mds requests to flush.
+ * flush the mdlog and wait for all write mds requests to flush.
  */
-static void wait_unsafe_requests(struct ceph_mds_client *mdsc, u64 want_tid)
+static void flush_mdlog_and_wait_mdsc_unsafe_requests(struct ceph_mds_client *mdsc,
+						 u64 want_tid)
 {
 	struct ceph_mds_request *req = NULL, *nextreq;
+	struct ceph_mds_session *last_session = NULL;
 	struct rb_node *n;
 
 	mutex_lock(&mdsc->mutex);
-	dout("wait_unsafe_requests want %lld\n", want_tid);
+	dout("%s want %lld\n", __func__, want_tid);
 restart:
 	req = __get_oldest_req(mdsc);
 	while (req && req->r_tid <= want_tid) {
@@ -4815,14 +4824,32 @@
 			nextreq = NULL;
 		if (req->r_op != CEPH_MDS_OP_SETFILELOCK &&
 		    (req->r_op & CEPH_MDS_OP_WRITE)) {
+			struct ceph_mds_session *s = req->r_session;
+
+			if (!s) {
+				req = nextreq;
+				continue;
+			}
+
 			/* write op */
 			ceph_mdsc_get_request(req);
 			if (nextreq)
 				ceph_mdsc_get_request(nextreq);
+			s = ceph_get_mds_session(s);
 			mutex_unlock(&mdsc->mutex);
-			dout("wait_unsafe_requests  wait on %llu (want %llu)\n",
+
+			/* send flush mdlog request to MDS */
+			if (last_session != s) {
+				send_flush_mdlog(s);
+				ceph_put_mds_session(last_session);
+				last_session = s;
+			} else {
+				ceph_put_mds_session(s);
+			}
+			dout("%s wait on %llu (want %llu)\n", __func__,
 			     req->r_tid, want_tid);
 			wait_for_completion(&req->r_safe_completion);
+
 			mutex_lock(&mdsc->mutex);
 			ceph_mdsc_put_request(req);
 			if (!nextreq)
@@ -4837,7 +4864,8 @@
 		req = nextreq;
 	}
 	mutex_unlock(&mdsc->mutex);
-	dout("wait_unsafe_requests done\n");
+	ceph_put_mds_session(last_session);
+	dout("%s done\n", __func__);
 }
 
 void ceph_mdsc_sync(struct ceph_mds_client *mdsc)
@@ -4866,7 +4894,7 @@
 	dout("sync want tid %lld flush_seq %lld\n",
 	     want_tid, want_flush);
 
-	wait_unsafe_requests(mdsc, want_tid);
+	flush_mdlog_and_wait_mdsc_unsafe_requests(mdsc, want_tid);
 	wait_caps_flush(mdsc, want_flush);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/mds_client.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/mds_client.h
@@ -33,10 +33,6 @@
 	CEPHFS_FEATURE_MAX = CEPHFS_FEATURE_METRIC_COLLECT,
 };
 
-/*
- * This will always have the highest feature bit value
- * as the last element of the array.
- */
 #define CEPHFS_FEATURES_CLIENT_SUPPORTED {	\
 	0, 1, 2, 3, 4, 5, 6, 7,			\
 	CEPHFS_FEATURE_MIMIC,			\
@@ -45,8 +41,6 @@
 	CEPHFS_FEATURE_MULTI_RECONNECT,		\
 	CEPHFS_FEATURE_DELEG_INO,		\
 	CEPHFS_FEATURE_METRIC_COLLECT,		\
-						\
-	CEPHFS_FEATURE_MAX,			\
 }
 #define CEPHFS_FEATURES_CLIENT_REQUIRED {}
 
@@ -376,6 +370,11 @@
 	int			want;
 };
 
+enum {
+       CEPH_MDSC_STOPPING_BEGIN = 1,
+       CEPH_MDSC_STOPPING_FLUSHED = 2,
+};
+
 /*
  * mds client state
  */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/mdsmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/mdsmap.c
@@ -263,10 +263,6 @@
 				goto nomem;
 			for (j = 0; j < num_export_targets; j++) {
 				target = ceph_decode_32(&pexport_targets);
-				if (target >= m->possible_max_rank) {
-					err = -EIO;
-					goto corrupt;
-				}
 				info->export_targets[j] = target;
 			}
 		} else {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/metric.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/metric.c
@@ -202,7 +202,7 @@
 	struct ceph_mds_client *mdsc =
 		container_of(m, struct ceph_mds_client, metric);
 
-	if (mdsc->stopping)
+	if (mdsc->stopping || disable_send_metrics)
 		return;
 
 	if (!m->session || !check_session_state(m->session)) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/snap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/snap.c
@@ -657,8 +657,10 @@
 	     capsnap->size);
 
 	spin_lock(&mdsc->snap_flush_lock);
-	if (list_empty(&ci->i_snap_flush_item))
+	if (list_empty(&ci->i_snap_flush_item)) {
+		ihold(inode);
 		list_add_tail(&ci->i_snap_flush_item, &mdsc->snap_flush_list);
+	}
 	spin_unlock(&mdsc->snap_flush_lock);
 	return 1;  /* caller may want to ceph_flush_snaps */
 }
@@ -705,9 +707,10 @@
 	struct ceph_mds_snap_realm *ri;    /* encoded */
 	__le64 *snaps;                     /* encoded */
 	__le64 *prior_parent_snaps;        /* encoded */
-	struct ceph_snap_realm *realm = NULL;
+	struct ceph_snap_realm *realm;
 	struct ceph_snap_realm *first_realm = NULL;
-	int invalidate = 0;
+	struct ceph_snap_realm *realm_to_rebuild = NULL;
+	int rebuild_snapcs;
 	int err = -ENOMEM;
 	LIST_HEAD(dirty_realms);
 
@@ -715,6 +718,8 @@
 
 	dout("update_snap_trace deletion=%d\n", deletion);
 more:
+	realm = NULL;
+	rebuild_snapcs = 0;
 	ceph_decode_need(&p, e, sizeof(*ri), bad);
 	ri = p;
 	p += sizeof(*ri);
@@ -738,7 +743,7 @@
 	err = adjust_snap_realm_parent(mdsc, realm, le64_to_cpu(ri->parent));
 	if (err < 0)
 		goto fail;
-	invalidate += err;
+	rebuild_snapcs += err;
 
 	if (le64_to_cpu(ri->seq) > realm->seq) {
 		dout("update_snap_trace updating %llx %p %lld -> %lld\n",
@@ -763,22 +768,30 @@
 		if (realm->seq > mdsc->last_snap_seq)
 			mdsc->last_snap_seq = realm->seq;
 
-		invalidate = 1;
+		rebuild_snapcs = 1;
 	} else if (!realm->cached_context) {
 		dout("update_snap_trace %llx %p seq %lld new\n",
 		     realm->ino, realm, realm->seq);
-		invalidate = 1;
+		rebuild_snapcs = 1;
 	} else {
 		dout("update_snap_trace %llx %p seq %lld unchanged\n",
 		     realm->ino, realm, realm->seq);
 	}
 
-	dout("done with %llx %p, invalidated=%d, %p %p\n", realm->ino,
-	     realm, invalidate, p, e);
+	dout("done with %llx %p, rebuild_snapcs=%d, %p %p\n", realm->ino,
+	     realm, rebuild_snapcs, p, e);
+
+	/*
+	 * this will always track the uppest parent realm from which
+	 * we need to rebuild the snapshot contexts _downward_ in
+	 * hierarchy.
+	 */
+	if (rebuild_snapcs)
+		realm_to_rebuild = realm;
 
-	/* invalidate when we reach the _end_ (root) of the trace */
-	if (invalidate && p >= e)
-		rebuild_snap_realms(realm, &dirty_realms);
+	/* rebuild_snapcs when we reach the _end_ (root) of the trace */
+	if (realm_to_rebuild && p >= e)
+		rebuild_snap_realms(realm_to_rebuild, &dirty_realms);
 
 	if (!first_realm)
 		first_realm = realm;
@@ -1017,6 +1030,19 @@
 				continue;
 			adjust_snap_realm_parent(mdsc, child, realm->ino);
 		}
+	} else {
+		/*
+		 * In the non-split case both 'num_split_inos' and
+		 * 'num_split_realms' should be 0, making this a no-op.
+		 * However the MDS happens to populate 'split_realms' list
+		 * in one of the UPDATE op cases by mistake.
+		 *
+		 * Skip both lists just in case to ensure that 'p' is
+		 * positioned at the start of realm info, as expected by
+		 * ceph_update_snap_trace().
+		 */
+		p += sizeof(u64) * num_split_inos;
+		p += sizeof(u64) * num_split_realms;
 	}
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/super.c
@@ -52,8 +52,7 @@
 	struct ceph_fs_client *fsc = ceph_inode_to_client(d_inode(dentry));
 	struct ceph_mon_client *monc = &fsc->client->monc;
 	struct ceph_statfs st;
-	u64 fsid;
-	int err;
+	int i, err;
 	u64 data_pool;
 
 	if (fsc->mdsc->mdsmap->m_num_data_pg_pools == 1) {
@@ -99,12 +98,14 @@
 	buf->f_namelen = NAME_MAX;
 
 	/* Must convert the fsid, for consistent values across arches */
+	buf->f_fsid.val[0] = 0;
 	mutex_lock(&monc->mutex);
-	fsid = le64_to_cpu(*(__le64 *)(&monc->monmap->fsid)) ^
-	       le64_to_cpu(*((__le64 *)&monc->monmap->fsid + 1));
+	for (i = 0 ; i < sizeof(monc->monmap->fsid) / sizeof(__le32) ; ++i)
+		buf->f_fsid.val[0] ^= le32_to_cpu(((__le32 *)&monc->monmap->fsid)[i]);
 	mutex_unlock(&monc->mutex);
 
-	buf->f_fsid = u64_to_fsid(fsid);
+	/* fold the fs_cluster_id into the upper bits */
+	buf->f_fsid.val[1] = monc->fs_cluster_id;
 
 	return 0;
 }
@@ -300,6 +301,8 @@
 
 	switch (token) {
 	case Opt_snapdirname:
+		if (strlen(param->string) > NAME_MAX)
+			return invalfc(fc, "snapdirname too long");
 		kfree(fsopt->snapdir_name);
 		fsopt->snapdir_name = param->string;
 		param->string = NULL;
@@ -782,7 +785,8 @@
 	if (!ceph_mds_request_cachep)
 		goto bad_mds_req;
 
-	ceph_wb_pagevec_pool = mempool_create_kmalloc_pool(10, CEPH_MAX_WRITE_SIZE >> PAGE_SHIFT);
+	ceph_wb_pagevec_pool = mempool_create_kmalloc_pool(10,
+	    (CEPH_MAX_WRITE_SIZE >> PAGE_SHIFT) * sizeof(struct page *));
 	if (!ceph_wb_pagevec_pool)
 		goto bad_pagevec_pool;
 
@@ -1226,6 +1230,16 @@
 	ceph_mdsc_pre_umount(fsc->mdsc);
 	flush_fs_workqueues(fsc);
 
+	/*
+	 * Though the kill_anon_super() will finally trigger the
+	 * sync_filesystem() anyway, we still need to do it here
+	 * and then bump the stage of shutdown to stop the work
+	 * queue as earlier as possible.
+	 */
+	sync_filesystem(s);
+
+	fsc->mdsc->stopping = CEPH_MDSC_STOPPING_FLUSHED;
+
 	kill_anon_super(s);
 
 	fsc->client->extra_mon_dispatch = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/super.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/super.h
@@ -773,7 +773,6 @@
 	struct list_head rw_contexts;
 
 	u32 filp_gen;
-	atomic_t num_locks;
 };
 
 struct ceph_dir_file_info {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ceph/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ceph/xattr.c
@@ -366,6 +366,14 @@
 	}
 #define XATTR_RSTAT_FIELD(_type, _name)			\
 	XATTR_NAME_CEPH(_type, _name, VXATTR_FLAG_RSTAT)
+#define XATTR_RSTAT_FIELD_UPDATABLE(_type, _name)			\
+	{								\
+		.name = CEPH_XATTR_NAME(_type, _name),			\
+		.name_size = sizeof (CEPH_XATTR_NAME(_type, _name)),	\
+		.getxattr_cb = ceph_vxattrcb_ ## _type ## _ ## _name,	\
+		.exists_cb = NULL,					\
+		.flags = VXATTR_FLAG_RSTAT,				\
+	}
 #define XATTR_LAYOUT_FIELD(_type, _name, _field)			\
 	{								\
 		.name = CEPH_XATTR_NAME2(_type, _name, _field),	\
@@ -404,7 +412,7 @@
 	XATTR_RSTAT_FIELD(dir, rsubdirs),
 	XATTR_RSTAT_FIELD(dir, rsnaps),
 	XATTR_RSTAT_FIELD(dir, rbytes),
-	XATTR_RSTAT_FIELD(dir, rctime),
+	XATTR_RSTAT_FIELD_UPDATABLE(dir, rctime),
 	{
 		.name = "ceph.dir.pin",
 		.name_size = sizeof("ceph.dir.pin"),
@@ -1375,12 +1383,16 @@
 
 void ceph_release_acl_sec_ctx(struct ceph_acl_sec_ctx *as_ctx)
 {
+#ifdef CONFIG_CEPH_FS_SECURITY_LABEL
+	struct lsmcontext scaff; /* scaffolding */
+#endif
 #ifdef CONFIG_CEPH_FS_POSIX_ACL
 	posix_acl_release(as_ctx->acl);
 	posix_acl_release(as_ctx->default_acl);
 #endif
 #ifdef CONFIG_CEPH_FS_SECURITY_LABEL
-	security_release_secctx(as_ctx->sec_ctx, as_ctx->sec_ctxlen);
+	lsmcontext_init(&scaff, as_ctx->sec_ctx, as_ctx->sec_ctxlen, 0);
+	security_release_secctx(&scaff);
 #endif
 	if (as_ctx->pagelist)
 		ceph_pagelist_release(as_ctx->pagelist);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/char_dev.c
+++ linux-xilinx-zynqmp-5.15.0/fs/char_dev.c
@@ -547,7 +547,7 @@
 	}
 
 	rc = device_add(dev);
-	if (rc)
+	if (rc && dev->devt)
 		cdev_del(cdev);
 
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifs_debug.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifs_debug.c
@@ -173,7 +173,7 @@
 
 	seq_puts(m, "# Version:1\n");
 	seq_puts(m, "# Format:\n");
-	seq_puts(m, "# <tree id> <persistent fid> <flags> <count> <pid> <uid>");
+	seq_puts(m, "# <tree id> <ses id> <persistent fid> <flags> <count> <pid> <uid>");
 #ifdef CONFIG_CIFS_DEBUG2
 	seq_printf(m, " <filename> <mid>\n");
 #else
@@ -183,6 +183,8 @@
 	list_for_each_entry(server, &cifs_tcp_ses_list, tcp_ses_list) {
 		list_for_each(tmp, &server->smb_ses_list) {
 			ses = list_entry(tmp, struct cifs_ses, smb_ses_list);
+			if (cifs_ses_exiting(ses))
+				continue;
 			list_for_each(tmp1, &ses->tcon_list) {
 				tcon = list_entry(tmp1, struct cifs_tcon, tcon_list);
 				spin_lock(&tcon->open_file_lock);
@@ -190,8 +192,9 @@
 					cfile = list_entry(tmp2, struct cifsFileInfo,
 						     tlist);
 					seq_printf(m,
-						"0x%x 0x%llx 0x%x %d %d %d %pd",
+						"0x%x 0x%llx 0x%llx 0x%x %d %d %d %pd",
 						tcon->tid,
+						ses->Suid,
 						cfile->fid.persistent_fid,
 						cfile->f_flags,
 						cfile->count,
@@ -358,6 +361,8 @@
 			seq_printf(m, " signed");
 		if (server->posix_ext_supported)
 			seq_printf(m, " posix");
+		if (server->nosharesock)
+			seq_printf(m, " nosharesock");
 
 		if (server->rdma)
 			seq_printf(m, "\nRDMA ");
@@ -377,6 +382,11 @@
 		list_for_each(tmp2, &server->smb_ses_list) {
 			ses = list_entry(tmp2, struct cifs_ses,
 					 smb_ses_list);
+			spin_lock(&GlobalMid_Lock);
+			if (ses->status == CifsExiting) {
+				spin_unlock(&GlobalMid_Lock);
+				continue;
+			}
 			i++;
 			if ((ses->serverDomain == NULL) ||
 				(ses->serverOS == NULL) ||
@@ -397,6 +407,7 @@
 				ses->ses_count, ses->serverOS, ses->serverNOS,
 				ses->capabilities, ses->status);
 			}
+			spin_unlock(&GlobalMid_Lock);
 
 			seq_printf(m, "\n\tSecurity type: %s ",
 				get_security_type_str(server->ops->select_sectype(server, ses->sectype)));
@@ -412,12 +423,14 @@
 				   from_kuid(&init_user_ns, ses->linux_uid),
 				   from_kuid(&init_user_ns, ses->cred_uid));
 
+			spin_lock(&ses->chan_lock);
 			if (ses->chan_count > 1) {
 				seq_printf(m, "\n\n\tExtra Channels: %zu ",
 					   ses->chan_count-1);
 				for (j = 1; j < ses->chan_count; j++)
 					cifs_dump_channel(m, j, &ses->chans[j]);
 			}
+			spin_unlock(&ses->chan_lock);
 
 			seq_puts(m, "\n\n\tShares: ");
 			j = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifs_dfs_ref.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifs_dfs_ref.c
@@ -258,65 +258,38 @@
 	goto compose_mount_options_out;
 }
 
-/**
- * cifs_dfs_do_mount - mounts specified path using DFS full path
- *
- * Always pass down @fullpath to smb3_do_mount() so we can use the root server
- * to perform failover in case we failed to connect to the first target in the
- * referral.
- *
- * @mntpt:		directory entry for the path we are trying to automount
- * @cifs_sb:		parent/root superblock
- * @fullpath:		full path in UNC format
- */
-static struct vfsmount *cifs_dfs_do_mount(struct dentry *mntpt,
-					  struct cifs_sb_info *cifs_sb,
-					  const char *fullpath)
+static void fs_context_set_ids(struct smb3_fs_context *ctx)
 {
-	struct vfsmount *mnt;
-	char *mountdata;
-	char *devname;
-
-	devname = kstrdup(fullpath, GFP_KERNEL);
-	if (!devname)
-		return ERR_PTR(-ENOMEM);
-
-	convert_delimiter(devname, '/');
+	kuid_t uid = current_fsuid();
+	kgid_t gid = current_fsgid();
 
-	/* TODO: change to call fs_context_for_mount(), fill in context directly, call fc_mount */
-
-	/* See afs_mntpt_do_automount in fs/afs/mntpt.c for an example */
-
-	/* strip first '\' from fullpath */
-	mountdata = cifs_compose_mount_options(cifs_sb->ctx->mount_options,
-					       fullpath + 1, NULL, NULL);
-	if (IS_ERR(mountdata)) {
-		kfree(devname);
-		return (struct vfsmount *)mountdata;
+	if (ctx->multiuser) {
+		if (!ctx->uid_specified)
+			ctx->linux_uid = uid;
+		if (!ctx->gid_specified)
+			ctx->linux_gid = gid;
 	}
-
-	mnt = vfs_submount(mntpt, &cifs_fs_type, devname, mountdata);
-	kfree(mountdata);
-	kfree(devname);
-	return mnt;
+	if (!ctx->cruid_specified)
+		ctx->cred_uid = uid;
 }
 
 /*
  * Create a vfsmount that we can automount
  */
-static struct vfsmount *cifs_dfs_do_automount(struct dentry *mntpt)
+static struct vfsmount *cifs_dfs_do_automount(struct path *path)
 {
-	struct cifs_sb_info *cifs_sb;
-	struct cifs_ses *ses;
-	struct cifs_tcon *tcon;
-	void *page;
-	char *full_path, *root_path;
-	unsigned int xid;
 	int rc;
+	struct dentry *mntpt = path->dentry;
+	struct fs_context *fc;
+	struct cifs_sb_info *cifs_sb;
+	void *page = NULL;
+	struct smb3_fs_context *ctx, *cur_ctx;
+	struct smb3_fs_context tmp;
+	char *full_path;
 	struct vfsmount *mnt;
 
-	cifs_dbg(FYI, "in %s\n", __func__);
-	BUG_ON(IS_ROOT(mntpt));
+	if (IS_ROOT(mntpt))
+		return ERR_PTR(-ESTALE);
 
 	/*
 	 * The MSDFS spec states that paths in DFS referral requests and
@@ -324,81 +297,49 @@
 	 * the double backslashes usually used in the UNC. This function
 	 * gives us the latter, so we must adjust the result.
 	 */
-	mnt = ERR_PTR(-ENOMEM);
-
 	cifs_sb = CIFS_SB(mntpt->d_sb);
-	if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_DFS) {
-		mnt = ERR_PTR(-EREMOTE);
-		goto cdda_exit;
-	}
+	if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_DFS)
+		return ERR_PTR(-EREMOTE);
+
+	cur_ctx = cifs_sb->ctx;
+
+	fc = fs_context_for_submount(path->mnt->mnt_sb->s_type, mntpt);
+	if (IS_ERR(fc))
+		return ERR_CAST(fc);
+
+	ctx = smb3_fc2context(fc);
 
 	page = alloc_dentry_path();
 	/* always use tree name prefix */
 	full_path = build_path_from_dentry_optional_prefix(mntpt, page, true);
 	if (IS_ERR(full_path)) {
 		mnt = ERR_CAST(full_path);
-		goto free_full_path;
+		goto out;
 	}
 
-	convert_delimiter(full_path, '\\');
-
+	convert_delimiter(full_path, '/');
 	cifs_dbg(FYI, "%s: full_path: %s\n", __func__, full_path);
 
-	if (!cifs_sb_master_tlink(cifs_sb)) {
-		cifs_dbg(FYI, "%s: master tlink is NULL\n", __func__);
-		goto free_full_path;
-	}
-
-	tcon = cifs_sb_master_tcon(cifs_sb);
-	if (!tcon) {
-		cifs_dbg(FYI, "%s: master tcon is NULL\n", __func__);
-		goto free_full_path;
-	}
-
-	root_path = kstrdup(tcon->treeName, GFP_KERNEL);
-	if (!root_path) {
-		mnt = ERR_PTR(-ENOMEM);
-		goto free_full_path;
-	}
-	cifs_dbg(FYI, "%s: root path: %s\n", __func__, root_path);
-
-	ses = tcon->ses;
-	xid = get_xid();
-
-	/*
-	 * If DFS root has been expired, then unconditionally fetch it again to
-	 * refresh DFS referral cache.
-	 */
-	rc = dfs_cache_find(xid, ses, cifs_sb->local_nls, cifs_remap(cifs_sb),
-			    root_path + 1, NULL, NULL);
-	if (!rc) {
-		rc = dfs_cache_find(xid, ses, cifs_sb->local_nls,
-				    cifs_remap(cifs_sb), full_path + 1,
-				    NULL, NULL);
-	}
-
-	free_xid(xid);
+	tmp = *cur_ctx;
+	tmp.source = full_path;
+	tmp.UNC = tmp.prepath = NULL;
+	fs_context_set_ids(&tmp);
 
+	rc = smb3_fs_context_dup(ctx, &tmp);
 	if (rc) {
 		mnt = ERR_PTR(rc);
-		goto free_root_path;
+		goto out;
 	}
-	/*
-	 * OK - we were able to get and cache a referral for @full_path.
-	 *
-	 * Now, pass it down to cifs_mount() and it will retry every available
-	 * node server in case of failures - no need to do it here.
-	 */
-	mnt = cifs_dfs_do_mount(mntpt, cifs_sb, full_path);
-	cifs_dbg(FYI, "%s: cifs_dfs_do_mount:%s , mnt:%p\n", __func__,
-		 full_path + 1, mnt);
-
-free_root_path:
-	kfree(root_path);
-free_full_path:
+
+	rc = smb3_parse_devname(full_path, ctx);
+	if (!rc)
+		mnt = fc_mount(fc);
+	else
+		mnt = ERR_PTR(rc);
+
+out:
+	put_fs_context(fc);
 	free_dentry_path(page);
-cdda_exit:
-	cifs_dbg(FYI, "leaving %s\n" , __func__);
 	return mnt;
 }
 
@@ -409,9 +350,9 @@
 {
 	struct vfsmount *newmnt;
 
-	cifs_dbg(FYI, "in %s\n", __func__);
+	cifs_dbg(FYI, "%s: %pd\n", __func__, path->dentry);
 
-	newmnt = cifs_dfs_do_automount(path->dentry);
+	newmnt = cifs_dfs_do_automount(path);
 	if (IS_ERR(newmnt)) {
 		cifs_dbg(FYI, "leaving %s [automount failed]\n" , __func__);
 		return newmnt;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifs_fs_sb.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifs_fs_sb.h
@@ -61,11 +61,6 @@
 	/* only used when CIFS_MOUNT_USE_PREFIX_PATH is set */
 	char *prepath;
 
-	/*
-	 * Canonical DFS path initially provided by the mount call. We might connect to something
-	 * different via DFS but we want to keep it to do failover properly.
-	 */
-	char *origin_fullpath; /* \\HOST\SHARE\[OPTIONAL PATH] */
 	/* randomly generated 128-bit number for indexing dfs mount groups in referral cache */
 	uuid_t dfs_mount_id;
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifs_spnego.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifs_spnego.c
@@ -64,8 +64,8 @@
  * strlen(";sec=ntlmsspi") */
 #define MAX_MECH_STR_LEN	13
 
-/* strlen of "host=" */
-#define HOST_KEY_LEN		5
+/* strlen of ";host=" */
+#define HOST_KEY_LEN		6
 
 /* strlen of ";ip4=" or ";ip6=" */
 #define IP_KEY_LEN		5
@@ -82,6 +82,9 @@
 /* strlen of ";pid=0x" */
 #define PID_KEY_LEN		7
 
+/* strlen of ";upcall_target=" */
+#define UPCALL_TARGET_KEY_LEN	15
+
 /* get a key struct with a SPNEGO security blob, suitable for session setup */
 struct key *
 cifs_get_spnego_key(struct cifs_ses *sesInfo)
@@ -108,6 +111,11 @@
 	if (sesInfo->user_name)
 		desc_len += USER_KEY_LEN + strlen(sesInfo->user_name);
 
+	if (sesInfo->upcall_target == UPTARGET_MOUNT)
+		desc_len += UPCALL_TARGET_KEY_LEN + 5; // strlen("mount")
+	else
+		desc_len += UPCALL_TARGET_KEY_LEN + 3; // strlen("app")
+
 	spnego_key = ERR_PTR(-ENOMEM);
 	description = kzalloc(desc_len, GFP_KERNEL);
 	if (description == NULL)
@@ -156,6 +164,14 @@
 	dp = description + strlen(description);
 	sprintf(dp, ";pid=0x%x", current->pid);
 
+	if (sesInfo->upcall_target == UPTARGET_MOUNT) {
+		dp = description + strlen(description);
+		sprintf(dp, ";upcall_target=mount");
+	} else {
+		dp = description + strlen(description);
+		sprintf(dp, ";upcall_target=app");
+	}
+
 	cifs_dbg(FYI, "key description = %s\n", description);
 	saved_cred = override_creds(spnego_cred);
 	spnego_key = request_key(&cifs_spnego_key_type, description, "");
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifsacl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifsacl.c
@@ -949,6 +949,9 @@
 		pnntace = (struct cifs_ace *) (nacl_base + nsize);
 		nsize += setup_special_mode_ACE(pnntace, nmode);
 		num_aces++;
+		pnntace = (struct cifs_ace *) (nacl_base + nsize);
+		nsize += setup_authusers_ACE(pnntace);
+		num_aces++;
 		goto set_size;
 	}
 
@@ -1297,7 +1300,7 @@
 
 		if (uid_valid(uid)) { /* chown */
 			uid_t id;
-			nowner_sid_ptr = kmalloc(sizeof(struct cifs_sid),
+			nowner_sid_ptr = kzalloc(sizeof(struct cifs_sid),
 								GFP_KERNEL);
 			if (!nowner_sid_ptr) {
 				rc = -ENOMEM;
@@ -1326,7 +1329,7 @@
 		}
 		if (gid_valid(gid)) { /* chgrp */
 			gid_t id;
-			ngroup_sid_ptr = kmalloc(sizeof(struct cifs_sid),
+			ngroup_sid_ptr = kzalloc(sizeof(struct cifs_sid),
 								GFP_KERNEL);
 			if (!ngroup_sid_ptr) {
 				rc = -ENOMEM;
@@ -1613,7 +1616,7 @@
 	nsecdesclen = secdesclen;
 	if (pnmode && *pnmode != NO_CHANGE_64) { /* chmod */
 		if (mode_from_sid)
-			nsecdesclen += sizeof(struct cifs_ace);
+			nsecdesclen += 2 * sizeof(struct cifs_ace);
 		else /* cifsacl */
 			nsecdesclen += 5 * sizeof(struct cifs_ace);
 	} else { /* chown */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifsfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifsfs.c
@@ -99,7 +99,7 @@
 MODULE_PARM_DESC(enable_oplocks, "Enable or disable oplocks. Default: y/Y/1");
 
 module_param(enable_gcm_256, bool, 0644);
-MODULE_PARM_DESC(enable_gcm_256, "Enable requesting strongest (256 bit) GCM encryption. Default: n/N/0");
+MODULE_PARM_DESC(enable_gcm_256, "Enable requesting strongest (256 bit) GCM encryption. Default: y/Y/0");
 
 module_param(require_gcm_256, bool, 0644);
 MODULE_PARM_DESC(require_gcm_256, "Require strongest (256 bit) GCM encryption. Default: n/N/0");
@@ -210,6 +210,9 @@
 	if (rc)
 		goto out_no_root;
 	/* tune readahead according to rsize if readahead size not set on mount */
+	if (cifs_sb->ctx->rsize == 0)
+		cifs_sb->ctx->rsize =
+			tcon->ses->server->ops->negotiate_rsize(tcon, cifs_sb->ctx);
 	if (cifs_sb->ctx->rasize)
 		sb->s_bdi->ra_pages = cifs_sb->ctx->rasize / PAGE_SIZE;
 	else
@@ -254,26 +257,33 @@
 	struct cifs_sb_info *cifs_sb = CIFS_SB(sb);
 	struct cifs_tcon *tcon;
 	struct cached_fid *cfid;
+	struct rb_root *root = &cifs_sb->tlink_tree;
+	struct rb_node *node;
+	struct tcon_link *tlink;
 
 	/*
 	 * We ned to release all dentries for the cached directories
 	 * before we kill the sb.
 	 */
 	if (cifs_sb->root) {
+		for (node = rb_first(root); node; node = rb_next(node)) {
+			tlink = rb_entry(node, struct tcon_link, tl_rbnode);
+			tcon = tlink_tcon(tlink);
+			if (IS_ERR(tcon))
+				continue;
+			cfid = &tcon->crfid;
+			mutex_lock(&cfid->fid_mutex);
+			if (cfid->dentry) {
+				dput(cfid->dentry);
+				cfid->dentry = NULL;
+			}
+			mutex_unlock(&cfid->fid_mutex);
+		}
+
+		/* finally release root dentry */
 		dput(cifs_sb->root);
 		cifs_sb->root = NULL;
 	}
-	tcon = cifs_sb_master_tcon(cifs_sb);
-	if (tcon) {
-		cfid = &tcon->crfid;
-		mutex_lock(&cfid->fid_mutex);
-		if (cfid->dentry) {
-
-			dput(cfid->dentry);
-			cfid->dentry = NULL;
-		}
-		mutex_unlock(&cfid->fid_mutex);
-	}
 
 	kill_anon_super(sb);
 	cifs_umount(cifs_sb);
@@ -364,6 +374,7 @@
 	 * server, can not assume caching of file data or metadata.
 	 */
 	cifs_set_oplock_level(cifs_inode, 0);
+	cifs_inode->lease_granted = false;
 	cifs_inode->flags = 0;
 	spin_lock_init(&cifs_inode->writers_lock);
 	cifs_inode->writers = 0;
@@ -496,6 +507,30 @@
 	return 0;
 }
 
+static void
+cifs_show_upcall_target(struct seq_file *s, struct cifs_sb_info *cifs_sb)
+{
+	if (cifs_sb->ctx->upcall_target == UPTARGET_UNSPECIFIED) {
+		seq_puts(s, ",upcall_target=app");
+		return;
+	}
+
+	seq_puts(s, ",upcall_target=");
+
+	switch (cifs_sb->ctx->upcall_target) {
+	case UPTARGET_APP:
+		seq_puts(s, "app");
+		break;
+	case UPTARGET_MOUNT:
+		seq_puts(s, "mount");
+		break;
+	default:
+		/* shouldn't ever happen */
+		seq_puts(s, "unknown");
+		break;
+	}
+}
+
 /*
  * cifs_show_options() is for displaying mount options in /proc/mounts.
  * Not all settable options are displayed but most of the important
@@ -512,6 +547,7 @@
 	seq_show_option(s, "vers", tcon->ses->server->vals->version_string);
 	cifs_show_security(s, tcon->ses);
 	cifs_show_cache_flavor(s, cifs_sb);
+	cifs_show_upcall_target(s, cifs_sb);
 
 	if (tcon->no_lease)
 		seq_puts(s, ",nolease");
@@ -646,9 +682,15 @@
 	seq_printf(s, ",echo_interval=%lu",
 			tcon->ses->server->echo_interval / HZ);
 
-	/* Only display max_credits if it was overridden on mount */
+	/* Only display the following if overridden on mount */
 	if (tcon->ses->server->max_credits != SMB2_MAX_CREDITS_AVAILABLE)
 		seq_printf(s, ",max_credits=%u", tcon->ses->server->max_credits);
+	if (tcon->ses->server->tcp_nodelay)
+		seq_puts(s, ",tcpnodelay");
+	if (tcon->ses->server->noautotune)
+		seq_puts(s, ",noautotune");
+	if (tcon->ses->server->noblocksnd)
+		seq_puts(s, ",noblocksend");
 
 	if (tcon->snapshot_time)
 		seq_printf(s, ",snapshot=%llu", tcon->snapshot_time);
@@ -666,6 +708,7 @@
 		seq_printf(s, ",acdirmax=%lu", cifs_sb->ctx->acdirmax / HZ);
 		seq_printf(s, ",acregmax=%lu", cifs_sb->ctx->acregmax / HZ);
 	}
+	seq_printf(s, ",closetimeo=%lu", cifs_sb->ctx->closetimeo / HZ);
 
 	if (tcon->ses->chan_max > 1)
 		seq_printf(s, ",multichannel,max_channels=%zu",
@@ -698,6 +741,7 @@
 		tcon->tidStatus = CifsExiting;
 	spin_unlock(&cifs_tcp_ses_lock);
 
+	cifs_close_all_deferred_files(tcon);
 	/* cancel_brl_requests(tcon); */ /* BB mark all brl mids as exiting */
 	/* cancel_notify_requests(tcon); */
 	if (tcon->ses && tcon->ses->server) {
@@ -713,6 +757,20 @@
 	return;
 }
 
+static int cifs_freeze(struct super_block *sb)
+{
+	struct cifs_sb_info *cifs_sb = CIFS_SB(sb);
+	struct cifs_tcon *tcon;
+
+	if (cifs_sb == NULL)
+		return 0;
+
+	tcon = cifs_sb_master_tcon(cifs_sb);
+
+	cifs_close_all_deferred_files(tcon);
+	return 0;
+}
+
 #ifdef CONFIG_CIFS_STATS2
 static int cifs_show_stats(struct seq_file *s, struct dentry *root)
 {
@@ -744,6 +802,7 @@
 	as opens */
 	.show_options = cifs_show_options,
 	.umount_begin   = cifs_umount_begin,
+	.freeze_fs      = cifs_freeze,
 #ifdef CONFIG_CIFS_STATS2
 	.show_stats = cifs_show_stats,
 #endif
@@ -815,11 +874,11 @@
 cifs_smb3_do_mount(struct file_system_type *fs_type,
 	      int flags, struct smb3_fs_context *old_ctx)
 {
-	int rc;
-	struct super_block *sb;
-	struct cifs_sb_info *cifs_sb = NULL;
 	struct cifs_mnt_data mnt_data;
+	struct cifs_sb_info *cifs_sb;
+	struct super_block *sb;
 	struct dentry *root;
+	int rc;
 
 	/*
 	 * Prints in Kernel / CIFS log the attempted mount operation
@@ -830,11 +889,9 @@
 	else
 		cifs_info("Attempting to mount %s\n", old_ctx->UNC);
 
-	cifs_sb = kzalloc(sizeof(struct cifs_sb_info), GFP_KERNEL);
-	if (cifs_sb == NULL) {
-		root = ERR_PTR(-ENOMEM);
-		goto out;
-	}
+	cifs_sb = kzalloc(sizeof(*cifs_sb), GFP_KERNEL);
+	if (!cifs_sb)
+		return ERR_PTR(-ENOMEM);
 
 	cifs_sb->ctx = kzalloc(sizeof(struct smb3_fs_context), GFP_KERNEL);
 	if (!cifs_sb->ctx) {
@@ -877,10 +934,8 @@
 
 	sb = sget(fs_type, cifs_match_super, cifs_set_super, flags, &mnt_data);
 	if (IS_ERR(sb)) {
-		root = ERR_CAST(sb);
 		cifs_umount(cifs_sb);
-		cifs_sb = NULL;
-		goto out;
+		return ERR_CAST(sb);
 	}
 
 	if (sb->s_root) {
@@ -909,12 +964,11 @@
 
 out_super:
 	deactivate_locked_super(sb);
+	return root;
 out:
-	if (cifs_sb) {
-		kfree(cifs_sb->prepath);
-		smb3_cleanup_fs_context(cifs_sb->ctx);
-		kfree(cifs_sb);
-	}
+	kfree(cifs_sb->prepath);
+	smb3_cleanup_fs_context(cifs_sb->ctx);
+	kfree(cifs_sb);
 	return root;
 }
 
@@ -925,7 +979,7 @@
 	ssize_t rc;
 	struct inode *inode = file_inode(iocb->ki_filp);
 
-	if (iocb->ki_filp->f_flags & O_DIRECT)
+	if (iocb->ki_flags & IOCB_DIRECT)
 		return cifs_user_readv(iocb, iter);
 
 	rc = cifs_revalidate_mapping(inode);
@@ -1061,7 +1115,7 @@
 };
 MODULE_ALIAS_FS("cifs");
 
-static struct file_system_type smb3_fs_type = {
+struct file_system_type smb3_fs_type = {
 	.owner = THIS_MODULE,
 	.name = "smb3",
 	.init_fs_context = smb3_init_fs_context,
@@ -1099,6 +1153,7 @@
 
 const struct inode_operations cifs_symlink_inode_ops = {
 	.get_link = cifs_get_link,
+	.setattr = cifs_setattr,
 	.permission = cifs_permission,
 	.listxattr = cifs_listxattr,
 };
@@ -1115,7 +1170,9 @@
 	unsigned int xid;
 	int rc;
 
-	if (remap_flags & ~(REMAP_FILE_DEDUP | REMAP_FILE_ADVISORY))
+	if (remap_flags & REMAP_FILE_DEDUP)
+		return -EOPNOTSUPP;
+	if (remap_flags & ~REMAP_FILE_ADVISORY)
 		return -EINVAL;
 
 	cifs_dbg(FYI, "clone range\n");
@@ -1250,8 +1307,11 @@
 	ssize_t rc;
 	struct cifsFileInfo *cfile = dst_file->private_data;
 
-	if (cfile->swapfile)
-		return -EOPNOTSUPP;
+	if (cfile->swapfile) {
+		rc = -EOPNOTSUPP;
+		free_xid(xid);
+		return rc;
+	}
 
 	rc = cifs_file_copychunk_range(xid, src_file, off, dst_file, destoff,
 					len, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifsfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifsfs.h
@@ -38,7 +38,7 @@
 	return (unsigned long) dentry->d_fsdata;
 }
 
-extern struct file_system_type cifs_fs_type;
+extern struct file_system_type cifs_fs_type, smb3_fs_type;
 extern const struct address_space_operations cifs_addr_ops;
 extern const struct address_space_operations cifs_addr_ops_smallbuf;
 
@@ -118,7 +118,10 @@
 #ifdef CONFIG_CIFS_DFS_UPCALL
 extern struct vfsmount *cifs_dfs_d_automount(struct path *path);
 #else
-#define cifs_dfs_d_automount NULL
+static inline struct vfsmount *cifs_dfs_d_automount(struct path *path)
+{
+	return ERR_PTR(-EREMOTE);
+}
 #endif
 
 /* Functions related to symlinks */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifsglob.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifsglob.h
@@ -13,6 +13,8 @@
 #include <linux/in6.h>
 #include <linux/inet.h>
 #include <linux/slab.h>
+#include <linux/scatterlist.h>
+#include <linux/mm.h>
 #include <linux/mempool.h>
 #include <linux/workqueue.h>
 #include "cifs_fs_sb.h"
@@ -21,6 +23,7 @@
 #include <linux/scatterlist.h>
 #include <uapi/linux/cifs/cifs_mount.h>
 #include "smb2pdu.h"
+#include "smb2glob.h"
 
 #define CIFS_MAGIC_NUMBER 0xFF534D42      /* the first four bytes of SMB PDUs */
 
@@ -74,7 +77,8 @@
 #define SMB_ECHO_INTERVAL_MAX 600
 #define SMB_ECHO_INTERVAL_DEFAULT 60
 
-/* dns resolution interval in seconds */
+/* dns resolution intervals in seconds */
+#define SMB_DNS_RESOLVE_INTERVAL_MIN     120
 #define SMB_DNS_RESOLVE_INTERVAL_DEFAULT 600
 
 /* maximum number of PDUs in one compound */
@@ -118,6 +122,11 @@
 	Kerberos,		/* Kerberos via SPNEGO */
 };
 
+enum upcall_target_enum {
+	UPTARGET_UNSPECIFIED, /* not specified, defaults to app */
+	UPTARGET_MOUNT, /* upcall to the mount namespace */
+	UPTARGET_APP, /* upcall to the application namespace which did the mount */
+};
 struct session_key {
 	unsigned int len;
 	char *response;
@@ -390,8 +399,8 @@
 	/* check for STATUS_NETWORK_SESSION_EXPIRED */
 	bool (*is_session_expired)(char *);
 	/* send oplock break response */
-	int (*oplock_response)(struct cifs_tcon *, struct cifs_fid *,
-			       struct cifsInodeInfo *);
+	int (*oplock_response)(struct cifs_tcon *tcon, __u64 persistent_fid, __u64 volatile_fid,
+			__u16 net_fid, struct cifsInodeInfo *cifs_inode);
 	/* query remote filesystem */
 	int (*queryfs)(const unsigned int, struct cifs_tcon *,
 		       struct cifs_sb_info *, struct kstatfs *);
@@ -591,6 +600,7 @@
 	struct list_head pending_mid_q;
 	bool noblocksnd;		/* use blocking sendmsg */
 	bool noautotune;		/* do not autotune send buf sizes */
+	bool nosharesock;
 	bool tcp_nodelay;
 	unsigned int credits;  /* send no more requests at once */
 	unsigned int max_credits; /* can override large 32000 default at mnt */
@@ -691,6 +701,19 @@
 #endif
 #ifdef CONFIG_CIFS_DFS_UPCALL
 	bool is_dfs_conn; /* if a dfs connection */
+	struct mutex refpath_lock; /* protects leaf_fullpath */
+	/*
+	 * Canonical DFS full paths that were used to chase referrals in mount and reconnect.
+	 *
+	 * origin_fullpath: first or original referral path
+	 * leaf_fullpath: last referral path (might be changed due to nested links in reconnect)
+	 *
+	 * current_fullpath: pointer to either origin_fullpath or leaf_fullpath
+	 * NOTE: cannot be accessed outside cifs_reconnect() and smb2_reconnect()
+	 *
+	 * format: \\HOST\SHARE\[OPTIONAL PATH]
+	 */
+	char *origin_fullpath, *leaf_fullpath, *current_fullpath;
 #endif
 };
 
@@ -910,6 +933,7 @@
 	struct session_key auth_key;
 	struct ntlmssp_auth *ntlmssp; /* ciphertext, flags, server challenge */
 	enum securityEnum sectype; /* what security flavor was specified? */
+	enum upcall_target_enum upcall_target; /* what upcall target was specified? */
 	bool sign;		/* is signing required? */
 	bool need_reconnect:1; /* connection reset, uid now invalid */
 	bool domainAuto:1;
@@ -932,16 +956,21 @@
 	 * iface_lock should be taken when accessing any of these fields
 	 */
 	spinlock_t iface_lock;
+	/* ========= begin: protected by iface_lock ======== */
 	struct cifs_server_iface *iface_list;
 	size_t iface_count;
 	unsigned long iface_last_update; /* jiffies */
+	/* ========= end: protected by iface_lock ======== */
 
+	spinlock_t chan_lock;
+	/* ========= begin: protected by chan_lock ======== */
 #define CIFS_MAX_CHANNELS 16
 	struct cifs_chan chans[CIFS_MAX_CHANNELS];
 	struct cifs_chan *binding_chan;
 	size_t chan_count;
 	size_t chan_max;
 	atomic_t chan_seq; /* round robin state */
+	/* ========= end: protected by chan_lock ======== */
 };
 
 /*
@@ -1090,7 +1119,6 @@
 	struct cached_fid crfid; /* Cached root fid */
 	/* BB add field for back pointer to sb struct(s)? */
 #ifdef CONFIG_CIFS_DFS_UPCALL
-	char *dfs_path; /* canonical DFS path */
 	struct list_head ulist; /* cache update list */
 #endif
 };
@@ -1883,11 +1911,13 @@
 
 /* Operations for different SMB versions */
 #define SMB1_VERSION_STRING	"1.0"
+#define SMB20_VERSION_STRING    "2.0"
+#ifdef CONFIG_CIFS_ALLOW_INSECURE_LEGACY
 extern struct smb_version_operations smb1_operations;
 extern struct smb_version_values smb1_values;
-#define SMB20_VERSION_STRING	"2.0"
 extern struct smb_version_operations smb20_operations;
 extern struct smb_version_values smb20_values;
+#endif /* CIFS_ALLOW_INSECURE_LEGACY */
 #define SMB21_VERSION_STRING	"2.1"
 extern struct smb_version_operations smb21_operations;
 extern struct smb_version_values smb21_values;
@@ -1941,4 +1971,88 @@
 		tcon->share_flags & (SHI1005_FLAGS_DFS | SHI1005_FLAGS_DFS_ROOT);
 }
 
+static inline bool cifs_is_referral_server(struct cifs_tcon *tcon,
+					   const struct dfs_info3_param *ref)
+{
+	/*
+	 * Check if all targets are capable of handling DFS referrals as per
+	 * MS-DFSC 2.2.4 RESP_GET_DFS_REFERRAL.
+	 */
+	return is_tcon_dfs(tcon) || (ref && (ref->flags & DFSREF_REFERRAL_SERVER));
+}
+
+static inline unsigned int cifs_get_num_sgs(const struct smb_rqst *rqst,
+					    int num_rqst,
+					    const u8 *sig)
+{
+	unsigned int len, skip;
+	unsigned int nents = 0;
+	unsigned long addr;
+	int i, j;
+
+	/* Assumes the first rqst has a transform header as the first iov.
+	 * I.e.
+	 * rqst[0].rq_iov[0]  is transform header
+	 * rqst[0].rq_iov[1+] data to be encrypted/decrypted
+	 * rqst[1+].rq_iov[0+] data to be encrypted/decrypted
+	 */
+	for (i = 0; i < num_rqst; i++) {
+		/*
+		 * The first rqst has a transform header where the
+		 * first 20 bytes are not part of the encrypted blob.
+		 */
+		for (j = 0; j < rqst[i].rq_nvec; j++) {
+			struct kvec *iov = &rqst[i].rq_iov[j];
+
+			skip = (i == 0) && (j == 0) ? 20 : 0;
+			addr = (unsigned long)iov->iov_base + skip;
+			if (unlikely(is_vmalloc_addr((void *)addr))) {
+				len = iov->iov_len - skip;
+				nents += DIV_ROUND_UP(offset_in_page(addr) + len,
+						      PAGE_SIZE);
+			} else {
+				nents++;
+			}
+		}
+		nents += rqst[i].rq_npages;
+	}
+	nents += DIV_ROUND_UP(offset_in_page(sig) + SMB2_SIGNATURE_SIZE, PAGE_SIZE);
+	return nents;
+}
+
+/* We can not use the normal sg_set_buf() as we will sometimes pass a
+ * stack object as buf.
+ */
+static inline struct scatterlist *cifs_sg_set_buf(struct scatterlist *sg,
+						  const void *buf,
+						  unsigned int buflen)
+{
+	unsigned long addr = (unsigned long)buf;
+	unsigned int off = offset_in_page(addr);
+
+	addr &= PAGE_MASK;
+	if (unlikely(is_vmalloc_addr((void *)addr))) {
+		do {
+			unsigned int len = min_t(unsigned int, buflen, PAGE_SIZE - off);
+
+			sg_set_page(sg++, vmalloc_to_page((void *)addr), len, off);
+
+			off = 0;
+			addr += PAGE_SIZE;
+			buflen -= len;
+		} while (buflen);
+	} else {
+		sg_set_page(sg++, virt_to_page(addr), buflen, off);
+	}
+	return sg;
+}
+
+static inline bool cifs_ses_exiting(struct cifs_ses *ses)
+{
+	bool ret;
+
+	ret = ses->status == CifsExiting;
+	return ret;
+}
+
 #endif	/* _CIFS_GLOB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifsproto.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifsproto.h
@@ -590,8 +590,8 @@
 		    struct sdesc **sdesc);
 void cifs_free_hash(struct crypto_shash **shash, struct sdesc **sdesc);
 
-extern void rqst_page_get_length(struct smb_rqst *rqst, unsigned int page,
-				unsigned int *len, unsigned int *offset);
+void rqst_page_get_length(const struct smb_rqst *rqst, unsigned int page,
+			  unsigned int *len, unsigned int *offset);
 struct cifs_chan *
 cifs_ses_find_chan(struct cifs_ses *ses, struct TCP_Server_Info *server);
 int cifs_try_adding_channels(struct cifs_sb_info *cifs_sb, struct cifs_ses *ses);
@@ -607,7 +607,7 @@
 
 struct super_block *cifs_get_tcp_super(struct TCP_Server_Info *server);
 void cifs_put_tcp_super(struct super_block *sb);
-int update_super_prepath(struct cifs_tcon *tcon, char *prefix);
+int cifs_update_super_prepath(struct cifs_sb_info *cifs_sb, char *prefix);
 char *extract_hostname(const char *unc);
 char *extract_sharename(const char *unc);
 
@@ -634,4 +634,7 @@
 		return options;
 }
 
+struct super_block *cifs_get_tcon_super(struct cifs_tcon *tcon);
+void cifs_put_tcon_super(struct super_block *sb);
+
 #endif			/* _CIFSPROTO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/cifssmb.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/cifssmb.c
@@ -4751,8 +4751,13 @@
 		return -ENODEV;
 
 getDFSRetry:
-	rc = smb_init(SMB_COM_TRANSACTION2, 15, ses->tcon_ipc, (void **) &pSMB,
-		      (void **) &pSMBr);
+	/*
+	 * Use smb_init_no_reconnect() instead of smb_init() as
+	 * CIFSGetDFSRefer() may be called from cifs_reconnect_tcon() and thus
+	 * causing an infinite recursion.
+	 */
+	rc = smb_init_no_reconnect(SMB_COM_TRANSACTION2, 15, ses->tcon_ipc,
+				   (void **)&pSMB, (void **)&pSMBr);
 	if (rc)
 		return rc;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/connect.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/connect.c
@@ -59,7 +59,21 @@
 #define TLINK_IDLE_EXPIRE	(600 * HZ)
 
 /* Drop the connection to not overload the server */
-#define NUM_STATUS_IO_TIMEOUT   5
+#define MAX_STATUS_IO_TIMEOUT   5
+
+struct mount_ctx {
+	struct cifs_sb_info *cifs_sb;
+	struct smb3_fs_context *fs_ctx;
+	unsigned int xid;
+	struct TCP_Server_Info *server;
+	struct cifs_ses *ses;
+	struct cifs_tcon *tcon;
+#ifdef CONFIG_CIFS_DFS_UPCALL
+	struct cifs_ses *root_ses;
+	uuid_t mount_id;
+	char *origin_fullpath, *leaf_fullpath;
+#endif
+};
 
 static int ip_connect(struct TCP_Server_Info *server);
 static int generic_ip_connect(struct TCP_Server_Info *server);
@@ -115,7 +129,7 @@
 			 * To make sure we don't use the cached entry, retry 1s
 			 * after expiry.
 			 */
-			ttl = (expiry - now + 1);
+			ttl = max_t(unsigned long, expiry - now, SMB_DNS_RESOLVE_INTERVAL_MIN) + 1;
 	}
 	rc = !rc ? -1 : 0;
 
@@ -148,131 +162,29 @@
 	mutex_unlock(&server->srv_mutex);
 }
 
-#ifdef CONFIG_CIFS_DFS_UPCALL
-/* These functions must be called with server->srv_mutex held */
-static void reconn_set_next_dfs_target(struct TCP_Server_Info *server,
-				       struct cifs_sb_info *cifs_sb,
-				       struct dfs_cache_tgt_list *tgt_list,
-				       struct dfs_cache_tgt_iterator **tgt_it)
-{
-	const char *name;
-	int rc;
-
-	if (!cifs_sb || !cifs_sb->origin_fullpath)
-		return;
-
-	if (!*tgt_it) {
-		*tgt_it = dfs_cache_get_tgt_iterator(tgt_list);
-	} else {
-		*tgt_it = dfs_cache_get_next_tgt(tgt_list, *tgt_it);
-		if (!*tgt_it)
-			*tgt_it = dfs_cache_get_tgt_iterator(tgt_list);
-	}
-
-	cifs_dbg(FYI, "%s: UNC: %s\n", __func__, cifs_sb->origin_fullpath);
-
-	name = dfs_cache_get_tgt_name(*tgt_it);
-
-	kfree(server->hostname);
-
-	server->hostname = extract_hostname(name);
-	if (IS_ERR(server->hostname)) {
-		cifs_dbg(FYI,
-			 "%s: failed to extract hostname from target: %ld\n",
-			 __func__, PTR_ERR(server->hostname));
-		return;
-	}
-
-	rc = reconn_set_ipaddr_from_hostname(server);
-	if (rc) {
-		cifs_dbg(FYI, "%s: failed to resolve hostname: %d\n",
-			 __func__, rc);
-	}
-}
-
-static inline int reconn_setup_dfs_targets(struct cifs_sb_info *cifs_sb,
-					   struct dfs_cache_tgt_list *tl)
-{
-	if (!cifs_sb->origin_fullpath)
-		return -EOPNOTSUPP;
-	return dfs_cache_noreq_find(cifs_sb->origin_fullpath + 1, NULL, tl);
-}
-#endif
-
-/*
- * cifs tcp session reconnection
+/**
+ * Mark all sessions and tcons for reconnect.
  *
- * mark tcp session as reconnecting so temporarily locked
- * mark all smb sessions as reconnecting for tcp session
- * reconnect tcp session
- * wake up waiters on reconnection? - (not needed currently)
+ * @server needs to be previously set to CifsNeedReconnect.
  */
-int
-cifs_reconnect(struct TCP_Server_Info *server)
+static void cifs_mark_tcp_ses_conns_for_reconnect(struct TCP_Server_Info *server)
 {
-	int rc = 0;
 	struct list_head *tmp, *tmp2;
 	struct cifs_ses *ses;
 	struct cifs_tcon *tcon;
 	struct mid_q_entry *mid_entry;
 	struct list_head retry_list;
-#ifdef CONFIG_CIFS_DFS_UPCALL
-	struct super_block *sb = NULL;
-	struct cifs_sb_info *cifs_sb = NULL;
-	struct dfs_cache_tgt_list tgt_list = DFS_CACHE_TGT_LIST_INIT(tgt_list);
-	struct dfs_cache_tgt_iterator *tgt_it = NULL;
-#endif
 
-	spin_lock(&GlobalMid_Lock);
-	server->nr_targets = 1;
-#ifdef CONFIG_CIFS_DFS_UPCALL
-	spin_unlock(&GlobalMid_Lock);
-	sb = cifs_get_tcp_super(server);
-	if (IS_ERR(sb)) {
-		rc = PTR_ERR(sb);
-		cifs_dbg(FYI, "%s: will not do DFS failover: rc = %d\n",
-			 __func__, rc);
-		sb = NULL;
-	} else {
-		cifs_sb = CIFS_SB(sb);
-		rc = reconn_setup_dfs_targets(cifs_sb, &tgt_list);
-		if (rc) {
-			cifs_sb = NULL;
-			if (rc != -EOPNOTSUPP) {
-				cifs_server_dbg(VFS, "%s: no target servers for DFS failover\n",
-						__func__);
-			}
-		} else {
-			server->nr_targets = dfs_cache_get_nr_tgts(&tgt_list);
-		}
-	}
-	cifs_dbg(FYI, "%s: will retry %d target(s)\n", __func__,
-		 server->nr_targets);
-	spin_lock(&GlobalMid_Lock);
-#endif
-	if (server->tcpStatus == CifsExiting) {
-		/* the demux thread will exit normally
-		next time through the loop */
-		spin_unlock(&GlobalMid_Lock);
-#ifdef CONFIG_CIFS_DFS_UPCALL
-		dfs_cache_free_tgts(&tgt_list);
-		cifs_put_tcp_super(sb);
-#endif
-		wake_up(&server->response_q);
-		return rc;
-	} else
-		server->tcpStatus = CifsNeedReconnect;
-	spin_unlock(&GlobalMid_Lock);
 	server->maxBuf = 0;
 	server->max_read = 0;
 
 	cifs_dbg(FYI, "Mark tcp session as need reconnect\n");
 	trace_smb3_reconnect(server->CurrentMid, server->conn_id, server->hostname);
-
-	/* before reconnecting the tcp session, mark the smb session (uid)
-		and the tid bad so they are not used until reconnected */
-	cifs_dbg(FYI, "%s: marking sessions and tcons for reconnect\n",
-		 __func__);
+	/*
+	 * before reconnecting the tcp session, mark the smb session (uid) and the tid bad so they
+	 * are not used until reconnected.
+	 */
+	cifs_dbg(FYI, "%s: marking sessions and tcons for reconnect\n", __func__);
 	spin_lock(&cifs_tcp_ses_lock);
 	list_for_each(tmp, &server->smb_ses_list) {
 		ses = list_entry(tmp, struct cifs_ses, smb_ses_list);
@@ -290,11 +202,11 @@
 	cifs_dbg(FYI, "%s: tearing down socket\n", __func__);
 	mutex_lock(&server->srv_mutex);
 	if (server->ssocket) {
-		cifs_dbg(FYI, "State: 0x%x Flags: 0x%lx\n",
-			 server->ssocket->state, server->ssocket->flags);
+		cifs_dbg(FYI, "State: 0x%x Flags: 0x%lx\n", server->ssocket->state,
+			 server->ssocket->flags);
 		kernel_sock_shutdown(server->ssocket, SHUT_WR);
-		cifs_dbg(FYI, "Post shutdown state: 0x%x Flags: 0x%lx\n",
-			 server->ssocket->state, server->ssocket->flags);
+		cifs_dbg(FYI, "Post shutdown state: 0x%x Flags: 0x%lx\n", server->ssocket->state,
+			 server->ssocket->flags);
 		sock_release(server->ssocket);
 		server->ssocket = NULL;
 	}
@@ -333,38 +245,48 @@
 		smbd_destroy(server);
 		mutex_unlock(&server->srv_mutex);
 	}
+}
+
+static bool cifs_tcp_ses_needs_reconnect(struct TCP_Server_Info *server, int num_targets)
+{
+	spin_lock(&GlobalMid_Lock);
+	server->nr_targets = num_targets;
+	if (server->tcpStatus == CifsExiting) {
+		/* the demux thread will exit normally next time through the loop */
+		spin_unlock(&GlobalMid_Lock);
+		wake_up(&server->response_q);
+		return false;
+	}
+	server->tcpStatus = CifsNeedReconnect;
+	spin_unlock(&GlobalMid_Lock);
+	return true;
+}
+
+/*
+ * cifs tcp session reconnection
+ *
+ * mark tcp session as reconnecting so temporarily locked
+ * mark all smb sessions as reconnecting for tcp session
+ * reconnect tcp session
+ * wake up waiters on reconnection? - (not needed currently)
+ */
+static int __cifs_reconnect(struct TCP_Server_Info *server)
+{
+	int rc = 0;
+
+	if (!cifs_tcp_ses_needs_reconnect(server, 1))
+		return 0;
+
+	cifs_mark_tcp_ses_conns_for_reconnect(server);
 
 	do {
 		try_to_freeze();
-
 		mutex_lock(&server->srv_mutex);
 
-
 		if (!cifs_swn_set_server_dstaddr(server)) {
-#ifdef CONFIG_CIFS_DFS_UPCALL
-		if (cifs_sb && cifs_sb->origin_fullpath)
-			/*
-			 * Set up next DFS target server (if any) for reconnect. If DFS
-			 * feature is disabled, then we will retry last server we
-			 * connected to before.
-			 */
-			reconn_set_next_dfs_target(server, cifs_sb, &tgt_list, &tgt_it);
-		else {
-#endif
-			/*
-			 * Resolve the hostname again to make sure that IP address is up-to-date.
-			 */
+			/* resolve the hostname again to make sure that IP address is up-to-date */
 			rc = reconn_set_ipaddr_from_hostname(server);
-			if (rc) {
-				cifs_dbg(FYI, "%s: failed to resolve hostname: %d\n",
-						__func__, rc);
-			}
-
-#ifdef CONFIG_CIFS_DFS_UPCALL
-		}
-#endif
-
-
+			cifs_dbg(FYI, "%s: reconn_set_ipaddr_from_hostname: rc=%d\n", __func__, rc);
 		}
 
 		if (cifs_rdma_enabled(server))
@@ -372,8 +294,8 @@
 		else
 			rc = generic_ip_connect(server);
 		if (rc) {
-			cifs_dbg(FYI, "reconnect error %d\n", rc);
 			mutex_unlock(&server->srv_mutex);
+			cifs_dbg(FYI, "%s: reconnect error %d\n", __func__, rc);
 			msleep(3000);
 		} else {
 			atomic_inc(&tcpSesReconnectCount);
@@ -387,19 +309,128 @@
 		}
 	} while (server->tcpStatus == CifsNeedReconnect);
 
+	if (server->tcpStatus == CifsNeedNegotiate)
+		mod_delayed_work(cifsiod_wq, &server->echo, 0);
+
+	wake_up(&server->response_q);
+	return rc;
+}
+
 #ifdef CONFIG_CIFS_DFS_UPCALL
-	if (tgt_it) {
-		rc = dfs_cache_noreq_update_tgthint(cifs_sb->origin_fullpath + 1,
-						    tgt_it);
-		if (rc) {
-			cifs_server_dbg(VFS, "%s: failed to update DFS target hint: rc = %d\n",
-				 __func__, rc);
+static int __reconnect_target_unlocked(struct TCP_Server_Info *server, const char *target)
+{
+	int rc;
+	char *hostname;
+
+	if (!cifs_swn_set_server_dstaddr(server)) {
+		if (server->hostname != target) {
+			hostname = extract_hostname(target);
+			if (!IS_ERR(hostname)) {
+				kfree(server->hostname);
+				server->hostname = hostname;
+			} else {
+				cifs_dbg(FYI, "%s: couldn't extract hostname or address from dfs target: %ld\n",
+					 __func__, PTR_ERR(hostname));
+				cifs_dbg(FYI, "%s: default to last target server: %s\n", __func__,
+					 server->hostname);
+			}
 		}
-		dfs_cache_free_tgts(&tgt_list);
+		/* resolve the hostname again to make sure that IP address is up-to-date. */
+		rc = reconn_set_ipaddr_from_hostname(server);
+		cifs_dbg(FYI, "%s: reconn_set_ipaddr_from_hostname: rc=%d\n", __func__, rc);
 	}
+	/* Reconnect the socket */
+	if (cifs_rdma_enabled(server))
+		rc = smbd_reconnect(server);
+	else
+		rc = generic_ip_connect(server);
 
-	cifs_put_tcp_super(sb);
-#endif
+	return rc;
+}
+
+static int reconnect_target_unlocked(struct TCP_Server_Info *server, struct dfs_cache_tgt_list *tl,
+				     struct dfs_cache_tgt_iterator **target_hint)
+{
+	int rc;
+	struct dfs_cache_tgt_iterator *tit;
+
+	*target_hint = NULL;
+
+	/* If dfs target list is empty, then reconnect to last server */
+	tit = dfs_cache_get_tgt_iterator(tl);
+	if (!tit)
+		return __reconnect_target_unlocked(server, server->hostname);
+
+	/* Otherwise, try every dfs target in @tl */
+	for (; tit; tit = dfs_cache_get_next_tgt(tl, tit)) {
+		rc = __reconnect_target_unlocked(server, dfs_cache_get_tgt_name(tit));
+		if (!rc) {
+			*target_hint = tit;
+			break;
+		}
+	}
+	return rc;
+}
+
+static int reconnect_dfs_server(struct TCP_Server_Info *server)
+{
+	int rc = 0;
+	const char *refpath = server->current_fullpath + 1;
+	struct dfs_cache_tgt_list tl = DFS_CACHE_TGT_LIST_INIT(tl);
+	struct dfs_cache_tgt_iterator *target_hint = NULL;
+	int num_targets = 0;
+
+	/*
+	 * Determine the number of dfs targets the referral path in @cifs_sb resolves to.
+	 *
+	 * smb2_reconnect() needs to know how long it should wait based upon the number of dfs
+	 * targets (server->nr_targets).  It's also possible that the cached referral was cleared
+	 * through /proc/fs/cifs/dfscache or the target list is empty due to server settings after
+	 * refreshing the referral, so, in this case, default it to 1.
+	 */
+	if (!dfs_cache_noreq_find(refpath, NULL, &tl))
+		num_targets = dfs_cache_get_nr_tgts(&tl);
+	if (!num_targets)
+		num_targets = 1;
+
+	if (!cifs_tcp_ses_needs_reconnect(server, num_targets))
+		return 0;
+
+	cifs_mark_tcp_ses_conns_for_reconnect(server);
+
+	do {
+		try_to_freeze();
+		mutex_lock(&server->srv_mutex);
+
+		rc = reconnect_target_unlocked(server, &tl, &target_hint);
+		if (rc) {
+			/* Failed to reconnect socket */
+			mutex_unlock(&server->srv_mutex);
+			cifs_dbg(FYI, "%s: reconnect error %d\n", __func__, rc);
+			msleep(3000);
+			continue;
+		}
+		/*
+		 * Socket was created.  Update tcp session status to CifsNeedNegotiate so that a
+		 * process waiting for reconnect will know it needs to re-establish session and tcon
+		 * through the reconnected target server.
+		 */
+		atomic_inc(&tcpSesReconnectCount);
+		set_credits(server, 1);
+		spin_lock(&GlobalMid_Lock);
+		if (server->tcpStatus != CifsExiting)
+			server->tcpStatus = CifsNeedNegotiate;
+		spin_unlock(&GlobalMid_Lock);
+		cifs_swn_reset_server_dstaddr(server);
+		mutex_unlock(&server->srv_mutex);
+	} while (server->tcpStatus == CifsNeedReconnect);
+
+	if (target_hint)
+		dfs_cache_noreq_update_tgthint(refpath, target_hint);
+
+	dfs_cache_free_tgts(&tl);
+
+	/* Need to set up echo worker again once connection has been established */
 	if (server->tcpStatus == CifsNeedNegotiate)
 		mod_delayed_work(cifsiod_wq, &server->echo, 0);
 
@@ -407,6 +438,25 @@
 	return rc;
 }
 
+int cifs_reconnect(struct TCP_Server_Info *server)
+{
+	/* If tcp session is not an dfs connection, then reconnect to last target server */
+	spin_lock(&cifs_tcp_ses_lock);
+	if (!server->is_dfs_conn || !server->origin_fullpath || !server->leaf_fullpath) {
+		spin_unlock(&cifs_tcp_ses_lock);
+		return __cifs_reconnect(server);
+	}
+	spin_unlock(&cifs_tcp_ses_lock);
+
+	return reconnect_dfs_server(server);
+}
+#else
+int cifs_reconnect(struct TCP_Server_Info *server)
+{
+	return __cifs_reconnect(server);
+}
+#endif
+
 static void
 cifs_echo_request(struct work_struct *work)
 {
@@ -519,9 +569,6 @@
 	int length = 0;
 	int total_read;
 
-	smb_msg->msg_control = NULL;
-	smb_msg->msg_controllen = 0;
-
 	for (total_read = 0; msg_data_left(smb_msg); total_read += length) {
 		try_to_freeze();
 
@@ -572,7 +619,7 @@
 cifs_read_from_socket(struct TCP_Server_Info *server, char *buf,
 		      unsigned int to_read)
 {
-	struct msghdr smb_msg;
+	struct msghdr smb_msg = {};
 	struct kvec iov = {.iov_base = buf, .iov_len = to_read};
 	iov_iter_kvec(&smb_msg.msg_iter, READ, &iov, 1, to_read);
 
@@ -582,15 +629,13 @@
 ssize_t
 cifs_discard_from_socket(struct TCP_Server_Info *server, size_t to_read)
 {
-	struct msghdr smb_msg;
+	struct msghdr smb_msg = {};
 
 	/*
 	 *  iov_iter_discard already sets smb_msg.type and count and iov_offset
 	 *  and cifs_readv_from_socket sets msg_control and msg_controllen
 	 *  so little to initialize in struct msghdr
 	 */
-	smb_msg.msg_name = NULL;
-	smb_msg.msg_namelen = 0;
 	iov_iter_discard(&smb_msg.msg_iter, READ, to_read);
 
 	return cifs_readv_from_socket(server, &smb_msg);
@@ -600,7 +645,7 @@
 cifs_read_page_from_socket(struct TCP_Server_Info *server, struct page *page,
 	unsigned int page_offset, unsigned int to_read)
 {
-	struct msghdr smb_msg;
+	struct msghdr smb_msg = {};
 	struct bio_vec bv = {
 		.bv_page = page, .bv_len = to_read, .bv_offset = page_offset};
 	iov_iter_bvec(&smb_msg.msg_iter, READ, &bv, 1, to_read);
@@ -794,7 +839,10 @@
 		 */
 	}
 
-	kfree(server->hostname);
+#ifdef CONFIG_CIFS_DFS_UPCALL
+	kfree(server->origin_fullpath);
+	kfree(server->leaf_fullpath);
+#endif
 	kfree(server);
 
 	length = atomic_dec_return(&tcpSesAllocCount);
@@ -917,6 +965,7 @@
 	struct mid_q_entry *mids[MAX_COMPOUND];
 	char *bufs[MAX_COMPOUND];
 	unsigned int noreclaim_flag, num_io_timeout = 0;
+	bool pending_reconnect = false;
 
 	noreclaim_flag = memalloc_noreclaim_save();
 	cifs_dbg(FYI, "Demultiplex PID: %d\n", task_pid_nr(current));
@@ -956,6 +1005,8 @@
 		cifs_dbg(FYI, "RFC1002 header 0x%x\n", pdu_length);
 		if (!is_smb_response(server, buf[0]))
 			continue;
+
+		pending_reconnect = false;
 next_pdu:
 		server->pdu_size = pdu_length;
 
@@ -1015,10 +1066,13 @@
 		if (server->ops->is_status_io_timeout &&
 		    server->ops->is_status_io_timeout(buf)) {
 			num_io_timeout++;
-			if (num_io_timeout > NUM_STATUS_IO_TIMEOUT) {
-				cifs_reconnect(server);
+			if (num_io_timeout > MAX_STATUS_IO_TIMEOUT) {
+				cifs_server_dbg(VFS,
+						"Number of request timeouts exceeded %d. Reconnecting",
+						MAX_STATUS_IO_TIMEOUT);
+
+				pending_reconnect = true;
 				num_io_timeout = 0;
-				continue;
 			}
 		}
 
@@ -1065,6 +1119,11 @@
 			buf = server->smallbuf;
 			goto next_pdu;
 		}
+
+		/* do this reconnect at the very end after processing all MIDs */
+		if (pending_reconnect)
+			cifs_reconnect(server);
+
 	} /* end while !EXITING */
 
 	/* buffer usually freed in free_mid - need to free it here on exit */
@@ -1086,7 +1145,7 @@
 	}
 
 	memalloc_noreclaim_restore(noreclaim_flag);
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 }
 
 /*
@@ -1221,6 +1280,10 @@
 	if (ctx->nosharesock)
 		return 0;
 
+	/* this server does not share socket */
+	if (server->nosharesock)
+		return 0;
+
 	/* If multidialect negotiation see if existing sessions match one */
 	if (strcmp(ctx->vals->version_string, SMB3ANY_VERSION_STRING) == 0) {
 		if (server->vals->protocol_id < SMB30_PROT_ID)
@@ -1235,6 +1298,9 @@
 	if (!net_eq(cifs_net_ns(server), current->nsproxy->net_ns))
 		return 0;
 
+	if (strcasecmp(server->hostname, ctx->server_hostname))
+		return 0;
+
 	if (!match_address(server, addr,
 			   (struct sockaddr *)&ctx->srcaddr))
 		return 0;
@@ -1336,6 +1402,8 @@
 	kfree(server->session_key.response);
 	server->session_key.response = NULL;
 	server->session_key.len = 0;
+	kfree(server->hostname);
+	server->hostname = NULL;
 
 	task = xchg(&server->tsk, NULL);
 	if (task)
@@ -1361,14 +1429,18 @@
 		goto out_err;
 	}
 
+	tcp_ses->hostname = kstrdup(ctx->server_hostname, GFP_KERNEL);
+	if (!tcp_ses->hostname) {
+		rc = -ENOMEM;
+		goto out_err;
+	}
+
+	if (ctx->nosharesock)
+		tcp_ses->nosharesock = true;
+
 	tcp_ses->ops = ctx->ops;
 	tcp_ses->vals = ctx->vals;
 	cifs_set_net_ns(tcp_ses, get_net(current->nsproxy->net_ns));
-	tcp_ses->hostname = extract_hostname(ctx->UNC);
-	if (IS_ERR(tcp_ses->hostname)) {
-		rc = PTR_ERR(tcp_ses->hostname);
-		goto out_err_crypto_release;
-	}
 
 	tcp_ses->conn_id = atomic_inc_return(&tcpSesNextId);
 	tcp_ses->noblockcnt = ctx->rootfs;
@@ -1399,6 +1471,9 @@
 	INIT_DELAYED_WORK(&tcp_ses->resolve, cifs_resolve_server);
 	INIT_DELAYED_WORK(&tcp_ses->reconnect, smb2_reconnect_server);
 	mutex_init(&tcp_ses->reconnect_mutex);
+#ifdef CONFIG_CIFS_DFS_UPCALL
+	mutex_init(&tcp_ses->refpath_lock);
+#endif
 	memcpy(&tcp_ses->srcaddr, &ctx->srcaddr,
 	       sizeof(tcp_ses->srcaddr));
 	memcpy(&tcp_ses->dstaddr, &ctx->dstaddr,
@@ -1497,8 +1572,7 @@
 
 out_err:
 	if (tcp_ses) {
-		if (!IS_ERR(tcp_ses->hostname))
-			kfree(tcp_ses->hostname);
+		kfree(tcp_ses->hostname);
 		if (tcp_ses->ssocket)
 			sock_release(tcp_ses->ssocket);
 		kfree(tcp_ses);
@@ -1508,22 +1582,33 @@
 
 static int match_session(struct cifs_ses *ses, struct smb3_fs_context *ctx)
 {
-	if (ctx->sectype != Unspecified &&
-	    ctx->sectype != ses->sectype)
-		return 0;
+	struct TCP_Server_Info *server = ses->server;
+	enum securityEnum ctx_sec, ses_sec;
 
 	/*
 	 * If an existing session is limited to less channels than
 	 * requested, it should not be reused
 	 */
-	if (ses->chan_max < ctx->max_channels)
+	spin_lock(&ses->chan_lock);
+	if (ses->chan_max < ctx->max_channels) {
+		spin_unlock(&ses->chan_lock);
 		return 0;
+	}
+	spin_unlock(&ses->chan_lock);
 
-	switch (ses->sectype) {
+	ctx_sec = server->ops->select_sectype(server, ctx->sectype);
+	ses_sec = server->ops->select_sectype(server, ses->sectype);
+
+	if (ctx_sec != ses_sec)
+		return 0;
+
+	switch (ctx_sec) {
 	case Kerberos:
 		if (!uid_eq(ctx->cred_uid, ses->cred_uid))
 			return 0;
 		break;
+	case NTLMv2:
+	case RawNTLMSSP:
 	default:
 		/* NULL username means anonymous session */
 		if (ses->user_name == NULL) {
@@ -1652,6 +1737,7 @@
 void cifs_put_smb_ses(struct cifs_ses *ses)
 {
 	unsigned int rc, xid;
+	unsigned int chan_count;
 	struct TCP_Server_Info *server = ses->server;
 	cifs_dbg(FYI, "%s: ses_count=%d\n", __func__, ses->ses_count);
 
@@ -1693,12 +1779,24 @@
 	list_del_init(&ses->smb_ses_list);
 	spin_unlock(&cifs_tcp_ses_lock);
 
+	spin_lock(&ses->chan_lock);
+	chan_count = ses->chan_count;
+	spin_unlock(&ses->chan_lock);
+
 	/* close any extra channels */
-	if (ses->chan_count > 1) {
+	if (chan_count > 1) {
 		int i;
 
-		for (i = 1; i < ses->chan_count; i++)
+		for (i = 1; i < chan_count; i++) {
+			/*
+			 * note: for now, we're okay accessing ses->chans
+			 * without chan_lock. But when chans can go away, we'll
+			 * need to introduce ref counting to make sure that chan
+			 * is not freed from under us.
+			 */
 			cifs_put_tcp_session(ses->chans[i].server, 0);
+			ses->chans[i].server = NULL;
+		}
 	}
 
 	sesInfoFree(ses);
@@ -1868,7 +1966,7 @@
 struct cifs_ses *
 cifs_get_smb_ses(struct TCP_Server_Info *server, struct smb3_fs_context *ctx)
 {
-	int rc = -ENOMEM;
+	int rc = 0;
 	unsigned int xid;
 	struct cifs_ses *ses;
 	struct sockaddr_in *addr = (struct sockaddr_in *)&server->dstaddr;
@@ -1910,6 +2008,8 @@
 		return ses;
 	}
 
+	rc = -ENOMEM;
+
 	cifs_dbg(FYI, "Existing smb sess not found\n");
 	ses = sesInfoAlloc();
 	if (ses == NULL)
@@ -1948,10 +2048,31 @@
 	ses->sign = ctx->sign;
 	mutex_lock(&ses->session_mutex);
 
+	/*
+	 *Explicitly marking upcall_target mount option for easier handling
+	 * by cifs_spnego.c and eventually cifs.upcall.c
+	 */
+
+	switch (ctx->upcall_target) {
+	case UPTARGET_UNSPECIFIED: /* default to app */
+	case UPTARGET_APP:
+		ses->upcall_target = UPTARGET_APP;
+		break;
+	case UPTARGET_MOUNT:
+		ses->upcall_target = UPTARGET_MOUNT;
+		break;
+	default:
+		// should never happen
+		ses->upcall_target = UPTARGET_APP;
+		break;
+	}
+
 	/* add server as first channel */
+	spin_lock(&ses->chan_lock);
 	ses->chans[0].server = server;
 	ses->chan_count = 1;
 	ses->chan_max = ctx->multichannel ? ctx->max_channels:1;
+	spin_unlock(&ses->chan_lock);
 
 	rc = cifs_negotiate_protocol(xid, ses);
 	if (!rc)
@@ -2352,6 +2473,8 @@
 		return 0;
 	if (old->ctx->acdirmax != new->ctx->acdirmax)
 		return 0;
+	if (old->ctx->closetimeo != new->ctx->closetimeo)
+		return 0;
 
 	return 1;
 }
@@ -2388,6 +2511,13 @@
 
 	spin_lock(&cifs_tcp_ses_lock);
 	cifs_sb = CIFS_SB(sb);
+
+	/* We do not want to use a superblock that has been shutdown */
+	if (CIFS_MOUNT_SHUTDOWN & cifs_sb->mnt_cifs_flags) {
+		spin_unlock(&cifs_tcp_ses_lock);
+		return 0;
+	}
+
 	tlink = cifs_get_tlink(cifs_sb_master_tlink(cifs_sb));
 	if (tlink == NULL) {
 		/* can not match superblock if tlink were ever null */
@@ -2845,73 +2975,64 @@
 }
 
 /* Release all succeed connections */
-static inline void mount_put_conns(struct cifs_sb_info *cifs_sb,
-				   unsigned int xid,
-				   struct TCP_Server_Info *server,
-				   struct cifs_ses *ses, struct cifs_tcon *tcon)
+static inline void mount_put_conns(struct mount_ctx *mnt_ctx)
 {
 	int rc = 0;
 
-	if (tcon)
-		cifs_put_tcon(tcon);
-	else if (ses)
-		cifs_put_smb_ses(ses);
-	else if (server)
-		cifs_put_tcp_session(server, 0);
-	cifs_sb->mnt_cifs_flags &= ~CIFS_MOUNT_POSIX_PATHS;
-	free_xid(xid);
+	if (mnt_ctx->tcon)
+		cifs_put_tcon(mnt_ctx->tcon);
+	else if (mnt_ctx->ses)
+		cifs_put_smb_ses(mnt_ctx->ses);
+	else if (mnt_ctx->server)
+		cifs_put_tcp_session(mnt_ctx->server, 0);
+	mnt_ctx->cifs_sb->mnt_cifs_flags &= ~CIFS_MOUNT_POSIX_PATHS;
+	free_xid(mnt_ctx->xid);
 }
 
 /* Get connections for tcp, ses and tcon */
-static int mount_get_conns(struct smb3_fs_context *ctx, struct cifs_sb_info *cifs_sb,
-			   unsigned int *xid,
-			   struct TCP_Server_Info **nserver,
-			   struct cifs_ses **nses, struct cifs_tcon **ntcon)
+static int mount_get_conns(struct mount_ctx *mnt_ctx)
 {
 	int rc = 0;
-	struct TCP_Server_Info *server;
-	struct cifs_ses *ses;
-	struct cifs_tcon *tcon;
-
-	*nserver = NULL;
-	*nses = NULL;
-	*ntcon = NULL;
+	struct TCP_Server_Info *server = NULL;
+	struct cifs_ses *ses = NULL;
+	struct cifs_tcon *tcon = NULL;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	unsigned int xid;
 
-	*xid = get_xid();
+	xid = get_xid();
 
 	/* get a reference to a tcp session */
 	server = cifs_get_tcp_session(ctx);
 	if (IS_ERR(server)) {
 		rc = PTR_ERR(server);
-		return rc;
+		server = NULL;
+		goto out;
 	}
 
-	*nserver = server;
-
 	/* get a reference to a SMB session */
 	ses = cifs_get_smb_ses(server, ctx);
 	if (IS_ERR(ses)) {
 		rc = PTR_ERR(ses);
-		return rc;
+		ses = NULL;
+		goto out;
 	}
 
-	*nses = ses;
-
 	if ((ctx->persistent == true) && (!(ses->server->capabilities &
 					    SMB2_GLOBAL_CAP_PERSISTENT_HANDLES))) {
 		cifs_server_dbg(VFS, "persistent handles not supported by server\n");
-		return -EOPNOTSUPP;
+		rc = -EOPNOTSUPP;
+		goto out;
 	}
 
 	/* search for existing tcon to this server share */
 	tcon = cifs_get_tcon(ses, ctx);
 	if (IS_ERR(tcon)) {
 		rc = PTR_ERR(tcon);
-		return rc;
+		tcon = NULL;
+		goto out;
 	}
 
-	*ntcon = tcon;
-
 	/* if new SMB3.11 POSIX extensions are supported do not remap / and \ */
 	if (tcon->posix_extensions)
 		cifs_sb->mnt_cifs_flags |= CIFS_MOUNT_POSIX_PATHS;
@@ -2922,17 +3043,19 @@
 		 * reset of caps checks mount to see if unix extensions disabled
 		 * for just this mount.
 		 */
-		reset_cifs_unix_caps(*xid, tcon, cifs_sb, ctx);
+		reset_cifs_unix_caps(xid, tcon, cifs_sb, ctx);
 		if ((tcon->ses->server->tcpStatus == CifsNeedReconnect) &&
 		    (le64_to_cpu(tcon->fsUnixInfo.Capability) &
-		     CIFS_UNIX_TRANSPORT_ENCRYPTION_MANDATORY_CAP))
-			return -EACCES;
+		     CIFS_UNIX_TRANSPORT_ENCRYPTION_MANDATORY_CAP)) {
+			rc = -EACCES;
+			goto out;
+		}
 	} else
 		tcon->unix_ext = 0; /* server does not support them */
 
 	/* do not care if a following call succeed - informational */
 	if (!tcon->pipe && server->ops->qfs_tcon) {
-		server->ops->qfs_tcon(*xid, tcon, cifs_sb);
+		server->ops->qfs_tcon(xid, tcon, cifs_sb);
 		if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_RO_CACHE) {
 			if (tcon->fsDevInfo.DeviceCharacteristics &
 			    cpu_to_le32(FILE_READ_ONLY_DEVICE))
@@ -2956,7 +3079,13 @@
 	    (cifs_sb->ctx->rsize > server->ops->negotiate_rsize(tcon, ctx)))
 		cifs_sb->ctx->rsize = server->ops->negotiate_rsize(tcon, ctx);
 
-	return 0;
+out:
+	mnt_ctx->server = server;
+	mnt_ctx->ses = ses;
+	mnt_ctx->tcon = tcon;
+	mnt_ctx->xid = xid;
+
+	return rc;
 }
 
 static int mount_setup_tlink(struct cifs_sb_info *cifs_sb, struct cifs_ses *ses,
@@ -2986,18 +3115,17 @@
 }
 
 #ifdef CONFIG_CIFS_DFS_UPCALL
-static int mount_get_dfs_conns(struct smb3_fs_context *ctx, struct cifs_sb_info *cifs_sb,
-			       unsigned int *xid, struct TCP_Server_Info **nserver,
-			       struct cifs_ses **nses, struct cifs_tcon **ntcon)
+/* Get unique dfs connections */
+static int mount_get_dfs_conns(struct mount_ctx *mnt_ctx)
 {
 	int rc;
 
-	ctx->nosharesock = true;
-	rc = mount_get_conns(ctx, cifs_sb, xid, nserver, nses, ntcon);
-	if (*nserver) {
+	mnt_ctx->fs_ctx->nosharesock = true;
+	rc = mount_get_conns(mnt_ctx);
+	if (mnt_ctx->server) {
 		cifs_dbg(FYI, "%s: marking tcp session as a dfs connection\n", __func__);
 		spin_lock(&cifs_tcp_ses_lock);
-		(*nserver)->is_dfs_conn = true;
+		mnt_ctx->server->is_dfs_conn = true;
 		spin_unlock(&cifs_tcp_ses_lock);
 	}
 	return rc;
@@ -3039,190 +3167,38 @@
 }
 
 /*
- * expand_dfs_referral - Perform a dfs referral query and update the cifs_sb
- *
- * If a referral is found, cifs_sb->ctx->mount_options will be (re-)allocated
- * to a string containing updated options for the submount.  Otherwise it
- * will be left untouched.
+ * expand_dfs_referral - Update cifs_sb from dfs referral path
  *
- * Returns the rc from get_dfs_path to the caller, which can be used to
- * determine whether there were referrals.
+ * cifs_sb->ctx->mount_options will be (re-)allocated to a string containing updated options for the
+ * submount.  Otherwise it will be left untouched.
  */
-static int
-expand_dfs_referral(const unsigned int xid, struct cifs_ses *ses,
-		    struct smb3_fs_context *ctx, struct cifs_sb_info *cifs_sb,
-		    char *ref_path)
-{
-	int rc;
-	struct dfs_info3_param referral = {0};
-	char *full_path = NULL, *mdata = NULL;
-
-	if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_DFS)
-		return -EREMOTE;
-
-	full_path = build_unc_path_to_root(ctx, cifs_sb, true);
-	if (IS_ERR(full_path))
-		return PTR_ERR(full_path);
-
-	rc = dfs_cache_find(xid, ses, cifs_sb->local_nls, cifs_remap(cifs_sb),
-			    ref_path, &referral, NULL);
-	if (!rc) {
-		char *fake_devname = NULL;
-
-		mdata = cifs_compose_mount_options(cifs_sb->ctx->mount_options,
-						   full_path + 1, &referral,
-						   &fake_devname);
-		free_dfs_info_param(&referral);
-
-		if (IS_ERR(mdata)) {
-			rc = PTR_ERR(mdata);
-			mdata = NULL;
-		} else {
-			/*
-			 * We can not clear out the whole structure since we
-			 * no longer have an explicit function to parse
-			 * a mount-string. Instead we need to clear out the
-			 * individual fields that are no longer valid.
-			 */
-			kfree(ctx->prepath);
-			ctx->prepath = NULL;
-			rc = cifs_setup_volume_info(ctx, mdata, fake_devname);
-		}
-		kfree(fake_devname);
-		kfree(cifs_sb->ctx->mount_options);
-		cifs_sb->ctx->mount_options = mdata;
-	}
-	kfree(full_path);
-	return rc;
-}
-
-static int get_next_dfs_tgt(struct dfs_cache_tgt_list *tgt_list,
-			    struct dfs_cache_tgt_iterator **tgt_it)
-{
-	if (!*tgt_it)
-		*tgt_it = dfs_cache_get_tgt_iterator(tgt_list);
-	else
-		*tgt_it = dfs_cache_get_next_tgt(tgt_list, *tgt_it);
-	return !*tgt_it ? -EHOSTDOWN : 0;
-}
-
-static int update_vol_info(const struct dfs_cache_tgt_iterator *tgt_it,
-			   struct smb3_fs_context *fake_ctx, struct smb3_fs_context *ctx)
-{
-	const char *tgt = dfs_cache_get_tgt_name(tgt_it);
-	int len = strlen(tgt) + 2;
-	char *new_unc;
-
-	new_unc = kmalloc(len, GFP_KERNEL);
-	if (!new_unc)
-		return -ENOMEM;
-	scnprintf(new_unc, len, "\\%s", tgt);
-
-	kfree(ctx->UNC);
-	ctx->UNC = new_unc;
-
-	if (fake_ctx->prepath) {
-		kfree(ctx->prepath);
-		ctx->prepath = fake_ctx->prepath;
-		fake_ctx->prepath = NULL;
-	}
-	memcpy(&ctx->dstaddr, &fake_ctx->dstaddr, sizeof(ctx->dstaddr));
-
-	return 0;
-}
-
-static int do_dfs_failover(const char *path, const char *full_path, struct cifs_sb_info *cifs_sb,
-			   struct smb3_fs_context *ctx, struct cifs_ses *root_ses,
-			   unsigned int *xid, struct TCP_Server_Info **server,
-			   struct cifs_ses **ses, struct cifs_tcon **tcon)
+static int expand_dfs_referral(struct mount_ctx *mnt_ctx, const char *full_path,
+			       struct dfs_info3_param *referral)
 {
 	int rc;
-	char *npath = NULL;
-	struct dfs_cache_tgt_list tgt_list = DFS_CACHE_TGT_LIST_INIT(tgt_list);
-	struct dfs_cache_tgt_iterator *tgt_it = NULL;
-	struct smb3_fs_context tmp_ctx = {NULL};
-
-	if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_DFS)
-		return -EOPNOTSUPP;
-
-	npath = dfs_cache_canonical_path(path, cifs_sb->local_nls, cifs_remap(cifs_sb));
-	if (IS_ERR(npath))
-		return PTR_ERR(npath);
-
-	cifs_dbg(FYI, "%s: path=%s full_path=%s\n", __func__, npath, full_path);
-
-	rc = dfs_cache_noreq_find(npath, NULL, &tgt_list);
-	if (rc)
-		goto out;
-	/*
-	 * We use a 'tmp_ctx' here because we need pass it down to the mount_{get,put} functions to
-	 * test connection against new DFS targets.
-	 */
-	rc = smb3_fs_context_dup(&tmp_ctx, ctx);
-	if (rc)
-		goto out;
-
-	for (;;) {
-		struct dfs_info3_param ref = {0};
-		char *fake_devname = NULL, *mdata = NULL;
-
-		/* Get next DFS target server - if any */
-		rc = get_next_dfs_tgt(&tgt_list, &tgt_it);
-		if (rc)
-			break;
-
-		rc = dfs_cache_get_tgt_referral(npath, tgt_it, &ref);
-		if (rc)
-			break;
-
-		cifs_dbg(FYI, "%s: old ctx: UNC=%s prepath=%s\n", __func__, tmp_ctx.UNC,
-			 tmp_ctx.prepath);
-
-		mdata = cifs_compose_mount_options(cifs_sb->ctx->mount_options, full_path + 1, &ref,
-						   &fake_devname);
-		free_dfs_info_param(&ref);
-
-		if (IS_ERR(mdata)) {
-			rc = PTR_ERR(mdata);
-			mdata = NULL;
-		} else
-			rc = cifs_setup_volume_info(&tmp_ctx, mdata, fake_devname);
-
-		kfree(mdata);
-		kfree(fake_devname);
-
-		if (rc)
-			break;
-
-		cifs_dbg(FYI, "%s: new ctx: UNC=%s prepath=%s\n", __func__, tmp_ctx.UNC,
-			 tmp_ctx.prepath);
-
-		mount_put_conns(cifs_sb, *xid, *server, *ses, *tcon);
-		rc = mount_get_dfs_conns(&tmp_ctx, cifs_sb, xid, server, ses, tcon);
-		if (!rc || (*server && *ses)) {
-			/*
-			 * We were able to connect to new target server. Update current context with
-			 * new target server.
-			 */
-			rc = update_vol_info(tgt_it, &tmp_ctx, ctx);
-			break;
-		}
-	}
-	if (!rc) {
-		cifs_dbg(FYI, "%s: final ctx: UNC=%s prepath=%s\n", __func__, tmp_ctx.UNC,
-			 tmp_ctx.prepath);
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
+	char *fake_devname = NULL, *mdata = NULL;
+
+	mdata = cifs_compose_mount_options(cifs_sb->ctx->mount_options, full_path + 1, referral,
+					   &fake_devname);
+	if (IS_ERR(mdata)) {
+		rc = PTR_ERR(mdata);
+		mdata = NULL;
+	} else {
 		/*
-		 * Update DFS target hint in DFS referral cache with the target server we
-		 * successfully reconnected to.
+		 * We can not clear out the whole structure since we no longer have an explicit
+		 * function to parse a mount-string. Instead we need to clear out the individual
+		 * fields that are no longer valid.
 		 */
-		rc = dfs_cache_update_tgthint(*xid, root_ses ? root_ses : *ses, cifs_sb->local_nls,
-					      cifs_remap(cifs_sb), path, tgt_it);
+		kfree(ctx->prepath);
+		ctx->prepath = NULL;
+		rc = cifs_setup_volume_info(ctx, mdata, fake_devname);
 	}
+	kfree(fake_devname);
+	kfree(cifs_sb->ctx->mount_options);
+	cifs_sb->ctx->mount_options = mdata;
 
-out:
-	kfree(npath);
-	smb3_cleanup_fs_context_contents(&tmp_ctx);
-	dfs_cache_free_tgts(&tgt_list);
 	return rc;
 }
 #endif
@@ -3329,12 +3305,14 @@
  * Check if path is remote (e.g. a DFS share). Return -EREMOTE if it is,
  * otherwise 0.
  */
-static int is_path_remote(struct cifs_sb_info *cifs_sb, struct smb3_fs_context *ctx,
-			  const unsigned int xid,
-			  struct TCP_Server_Info *server,
-			  struct cifs_tcon *tcon)
+static int is_path_remote(struct mount_ctx *mnt_ctx)
 {
 	int rc;
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	struct TCP_Server_Info *server = mnt_ctx->server;
+	unsigned int xid = mnt_ctx->xid;
+	struct cifs_tcon *tcon = mnt_ctx->tcon;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
 	char *full_path;
 
 	if (!server->ops->is_path_accessible)
@@ -3372,280 +3350,298 @@
 }
 
 #ifdef CONFIG_CIFS_DFS_UPCALL
-static void set_root_ses(struct cifs_sb_info *cifs_sb, const uuid_t *mount_id, struct cifs_ses *ses,
-			 struct cifs_ses **root_ses)
+static void set_root_ses(struct mount_ctx *mnt_ctx)
 {
-	if (ses) {
+	if (mnt_ctx->ses) {
 		spin_lock(&cifs_tcp_ses_lock);
-		ses->ses_count++;
+		mnt_ctx->ses->ses_count++;
 		spin_unlock(&cifs_tcp_ses_lock);
-		dfs_cache_add_refsrv_session(mount_id, ses);
+		dfs_cache_add_refsrv_session(&mnt_ctx->mount_id, mnt_ctx->ses);
 	}
-	*root_ses = ses;
+	mnt_ctx->root_ses = mnt_ctx->ses;
 }
 
-/* Set up next dfs prefix path in @dfs_path */
-static int next_dfs_prepath(struct cifs_sb_info *cifs_sb, struct smb3_fs_context *ctx,
-			    const unsigned int xid, struct TCP_Server_Info *server,
-			    struct cifs_tcon *tcon, char **dfs_path)
+static int is_dfs_mount(struct mount_ctx *mnt_ctx, bool *isdfs, struct dfs_cache_tgt_list *root_tl)
 {
-	char *path, *npath;
-	int added_treename = is_tcon_dfs(tcon);
 	int rc;
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
 
-	path = cifs_build_path_to_root(ctx, cifs_sb, tcon, added_treename);
-	if (!path)
-		return -ENOMEM;
+	*isdfs = true;
 
-	rc = is_path_remote(cifs_sb, ctx, xid, server, tcon);
-	if (rc == -EREMOTE) {
-		struct smb3_fs_context v = {NULL};
-		/* if @path contains a tree name, skip it in the prefix path */
-		if (added_treename) {
-			rc = smb3_parse_devname(path, &v);
-			if (rc)
-				goto out;
-			npath = build_unc_path_to_root(&v, cifs_sb, true);
-			smb3_cleanup_fs_context_contents(&v);
-		} else {
-			v.UNC = ctx->UNC;
-			v.prepath = path + 1;
-			npath = build_unc_path_to_root(&v, cifs_sb, true);
-		}
+	rc = mount_get_conns(mnt_ctx);
+	/*
+	 * If called with 'nodfs' mount option, then skip DFS resolving.  Otherwise unconditionally
+	 * try to get an DFS referral (even cached) to determine whether it is an DFS mount.
+	 *
+	 * Skip prefix path to provide support for DFS referrals from w2k8 servers which don't seem
+	 * to respond with PATH_NOT_COVERED to requests that include the prefix.
+	 */
+	if ((cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_DFS) ||
+	    dfs_cache_find(mnt_ctx->xid, mnt_ctx->ses, cifs_sb->local_nls, cifs_remap(cifs_sb),
+			   ctx->UNC + 1, NULL, root_tl)) {
+		if (rc)
+			return rc;
+		/* Check if it is fully accessible and then mount it */
+		rc = is_path_remote(mnt_ctx);
+		if (!rc)
+			*isdfs = false;
+		else if (rc != -EREMOTE)
+			return rc;
+	}
+	return 0;
+}
 
-		if (IS_ERR(npath)) {
-			rc = PTR_ERR(npath);
-			goto out;
-		}
+static int connect_dfs_target(struct mount_ctx *mnt_ctx, const char *full_path,
+			      const char *ref_path, struct dfs_cache_tgt_iterator *tit)
+{
+	int rc;
+	struct dfs_info3_param ref = {};
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	char *oldmnt = cifs_sb->ctx->mount_options;
+
+	rc = dfs_cache_get_tgt_referral(ref_path, tit, &ref);
+	if (rc)
+		goto out;
+
+	rc = expand_dfs_referral(mnt_ctx, full_path, &ref);
+	if (rc)
+		goto out;
 
-		kfree(*dfs_path);
-		*dfs_path = npath;
-		rc = -EREMOTE;
+	/* Connect to new target only if we were redirected (e.g. mount options changed) */
+	if (oldmnt != cifs_sb->ctx->mount_options) {
+		mount_put_conns(mnt_ctx);
+		rc = mount_get_dfs_conns(mnt_ctx);
+	}
+	if (!rc) {
+		if (cifs_is_referral_server(mnt_ctx->tcon, &ref))
+			set_root_ses(mnt_ctx);
+		rc = dfs_cache_update_tgthint(mnt_ctx->xid, mnt_ctx->root_ses, cifs_sb->local_nls,
+					      cifs_remap(cifs_sb), ref_path, tit);
 	}
 
 out:
-	kfree(path);
+	free_dfs_info_param(&ref);
 	return rc;
 }
 
-/* Check if resolved targets can handle any DFS referrals */
-static int is_referral_server(const char *ref_path, struct cifs_sb_info *cifs_sb,
-			      struct cifs_tcon *tcon, bool *ref_server)
+static int connect_dfs_root(struct mount_ctx *mnt_ctx, struct dfs_cache_tgt_list *root_tl)
 {
 	int rc;
-	struct dfs_info3_param ref = {0};
-
-	cifs_dbg(FYI, "%s: ref_path=%s\n", __func__, ref_path);
+	char *full_path;
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
+	struct dfs_cache_tgt_iterator *tit;
+
+	/* Put initial connections as they might be shared with other mounts.  We need unique dfs
+	 * connections per mount to properly failover, so mount_get_dfs_conns() must be used from
+	 * now on.
+	 */
+	mount_put_conns(mnt_ctx);
+	mount_get_dfs_conns(mnt_ctx);
+	set_root_ses(mnt_ctx);
 
-	if (is_tcon_dfs(tcon)) {
-		*ref_server = true;
-	} else {
-		char *npath;
+	full_path = build_unc_path_to_root(ctx, cifs_sb, true);
+	if (IS_ERR(full_path))
+		return PTR_ERR(full_path);
 
-		npath = dfs_cache_canonical_path(ref_path, cifs_sb->local_nls, cifs_remap(cifs_sb));
-		if (IS_ERR(npath))
-			return PTR_ERR(npath);
+	mnt_ctx->origin_fullpath = dfs_cache_canonical_path(ctx->UNC, cifs_sb->local_nls,
+							    cifs_remap(cifs_sb));
+	if (IS_ERR(mnt_ctx->origin_fullpath)) {
+		rc = PTR_ERR(mnt_ctx->origin_fullpath);
+		mnt_ctx->origin_fullpath = NULL;
+		goto out;
+	}
 
-		rc = dfs_cache_noreq_find(npath, &ref, NULL);
-		kfree(npath);
-		if (rc) {
-			cifs_dbg(VFS, "%s: dfs_cache_noreq_find: failed (rc=%d)\n", __func__, rc);
-			return rc;
+	/* Try all dfs root targets */
+	for (rc = -ENOENT, tit = dfs_cache_get_tgt_iterator(root_tl);
+	     tit; tit = dfs_cache_get_next_tgt(root_tl, tit)) {
+		rc = connect_dfs_target(mnt_ctx, full_path, mnt_ctx->origin_fullpath + 1, tit);
+		if (!rc) {
+			mnt_ctx->leaf_fullpath = kstrdup(mnt_ctx->origin_fullpath, GFP_KERNEL);
+			if (!mnt_ctx->leaf_fullpath)
+				rc = -ENOMEM;
+			break;
 		}
-		cifs_dbg(FYI, "%s: ref.flags=0x%x\n", __func__, ref.flags);
-		/*
-		 * Check if all targets are capable of handling DFS referrals as per
-		 * MS-DFSC 2.2.4 RESP_GET_DFS_REFERRAL.
-		 */
-		*ref_server = !!(ref.flags & DFSREF_REFERRAL_SERVER);
-		free_dfs_info_param(&ref);
 	}
-	return 0;
+
+out:
+	kfree(full_path);
+	return rc;
 }
 
-int cifs_mount(struct cifs_sb_info *cifs_sb, struct smb3_fs_context *ctx)
+static int __follow_dfs_link(struct mount_ctx *mnt_ctx)
 {
-	int rc = 0;
-	unsigned int xid;
-	struct TCP_Server_Info *server = NULL;
-	struct cifs_ses *ses = NULL, *root_ses = NULL;
-	struct cifs_tcon *tcon = NULL;
-	int count = 0;
-	uuid_t mount_id = {0};
-	char *ref_path = NULL, *full_path = NULL;
-	char *oldmnt = NULL;
-	bool ref_server = false;
+	int rc;
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
+	char *full_path;
+	struct dfs_cache_tgt_list tl = DFS_CACHE_TGT_LIST_INIT(tl);
+	struct dfs_cache_tgt_iterator *tit;
 
-	rc = mount_get_conns(ctx, cifs_sb, &xid, &server, &ses, &tcon);
-	/*
-	 * If called with 'nodfs' mount option, then skip DFS resolving.  Otherwise unconditionally
-	 * try to get an DFS referral (even cached) to determine whether it is an DFS mount.
-	 *
-	 * Skip prefix path to provide support for DFS referrals from w2k8 servers which don't seem
-	 * to respond with PATH_NOT_COVERED to requests that include the prefix.
-	 */
-	if ((cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_DFS) ||
-	    dfs_cache_find(xid, ses, cifs_sb->local_nls, cifs_remap(cifs_sb), ctx->UNC + 1, NULL,
-			   NULL)) {
-		if (rc)
-			goto error;
-		/* Check if it is fully accessible and then mount it */
-		rc = is_path_remote(cifs_sb, ctx, xid, server, tcon);
-		if (!rc)
-			goto out;
-		if (rc != -EREMOTE)
-			goto error;
+	full_path = build_unc_path_to_root(ctx, cifs_sb, true);
+	if (IS_ERR(full_path))
+		return PTR_ERR(full_path);
+
+	kfree(mnt_ctx->leaf_fullpath);
+	mnt_ctx->leaf_fullpath = dfs_cache_canonical_path(full_path, cifs_sb->local_nls,
+							  cifs_remap(cifs_sb));
+	if (IS_ERR(mnt_ctx->leaf_fullpath)) {
+		rc = PTR_ERR(mnt_ctx->leaf_fullpath);
+		mnt_ctx->leaf_fullpath = NULL;
+		goto out;
 	}
 
-	mount_put_conns(cifs_sb, xid, server, ses, tcon);
-	/*
-	 * Ignore error check here because we may failover to other targets from cached a
-	 * referral.
-	 */
-	(void)mount_get_dfs_conns(ctx, cifs_sb, &xid, &server, &ses, &tcon);
+	/* Get referral from dfs link */
+	rc = dfs_cache_find(mnt_ctx->xid, mnt_ctx->root_ses, cifs_sb->local_nls,
+			    cifs_remap(cifs_sb), mnt_ctx->leaf_fullpath + 1, NULL, &tl);
+	if (rc)
+		goto out;
 
-	/* Get path of DFS root */
-	ref_path = build_unc_path_to_root(ctx, cifs_sb, false);
-	if (IS_ERR(ref_path)) {
-		rc = PTR_ERR(ref_path);
-		ref_path = NULL;
-		goto error;
+	/* Try all dfs link targets */
+	for (rc = -ENOENT, tit = dfs_cache_get_tgt_iterator(&tl);
+	     tit; tit = dfs_cache_get_next_tgt(&tl, tit)) {
+		rc = connect_dfs_target(mnt_ctx, full_path, mnt_ctx->leaf_fullpath + 1, tit);
+		if (!rc) {
+			rc = is_path_remote(mnt_ctx);
+			break;
+		}
+	}
+
+out:
+	kfree(full_path);
+	dfs_cache_free_tgts(&tl);
+	return rc;
+}
+
+static int follow_dfs_link(struct mount_ctx *mnt_ctx)
+{
+	int rc;
+	struct cifs_sb_info *cifs_sb = mnt_ctx->cifs_sb;
+	struct smb3_fs_context *ctx = mnt_ctx->fs_ctx;
+	char *full_path;
+	int num_links = 0;
+
+	full_path = build_unc_path_to_root(ctx, cifs_sb, true);
+	if (IS_ERR(full_path))
+		return PTR_ERR(full_path);
+
+	kfree(mnt_ctx->origin_fullpath);
+	mnt_ctx->origin_fullpath = dfs_cache_canonical_path(full_path, cifs_sb->local_nls,
+							    cifs_remap(cifs_sb));
+	kfree(full_path);
+
+	if (IS_ERR(mnt_ctx->origin_fullpath)) {
+		rc = PTR_ERR(mnt_ctx->origin_fullpath);
+		mnt_ctx->origin_fullpath = NULL;
+		return rc;
 	}
 
-	uuid_gen(&mount_id);
-	set_root_ses(cifs_sb, &mount_id, ses, &root_ses);
 	do {
-		/* Save full path of last DFS path we used to resolve final target server */
-		kfree(full_path);
-		full_path = build_unc_path_to_root(ctx, cifs_sb, !!count);
-		if (IS_ERR(full_path)) {
-			rc = PTR_ERR(full_path);
-			full_path = NULL;
-			break;
-		}
-		/* Chase referral */
-		oldmnt = cifs_sb->ctx->mount_options;
-		rc = expand_dfs_referral(xid, root_ses, ctx, cifs_sb, ref_path + 1);
-		if (rc)
+		rc = __follow_dfs_link(mnt_ctx);
+		if (!rc || rc != -EREMOTE)
 			break;
-		/* Connect to new DFS target only if we were redirected */
-		if (oldmnt != cifs_sb->ctx->mount_options) {
-			mount_put_conns(cifs_sb, xid, server, ses, tcon);
-			rc = mount_get_dfs_conns(ctx, cifs_sb, &xid, &server, &ses, &tcon);
-		}
-		if (rc && !server && !ses) {
-			/* Failed to connect. Try to connect to other targets in the referral. */
-			rc = do_dfs_failover(ref_path + 1, full_path, cifs_sb, ctx, root_ses, &xid,
-					     &server, &ses, &tcon);
-		}
-		if (rc == -EACCES || rc == -EOPNOTSUPP || !server || !ses)
-			break;
-		if (!tcon)
-			continue;
+	} while (rc = -ELOOP, ++num_links < MAX_NESTED_LINKS);
 
-		/* Make sure that requests go through new root servers */
-		rc = is_referral_server(ref_path + 1, cifs_sb, tcon, &ref_server);
-		if (rc)
-			break;
-		if (ref_server)
-			set_root_ses(cifs_sb, &mount_id, ses, &root_ses);
+	return rc;
+}
+
+/* Set up DFS referral paths for failover */
+static void setup_server_referral_paths(struct mount_ctx *mnt_ctx)
+{
+	struct TCP_Server_Info *server = mnt_ctx->server;
 
-		/* Get next dfs path and then continue chasing them if -EREMOTE */
-		rc = next_dfs_prepath(cifs_sb, ctx, xid, server, tcon, &ref_path);
-		/* Prevent recursion on broken link referrals */
-		if (rc == -EREMOTE && ++count > MAX_NESTED_LINKS)
-			rc = -ELOOP;
-	} while (rc == -EREMOTE);
+	server->origin_fullpath = mnt_ctx->origin_fullpath;
+	server->leaf_fullpath = mnt_ctx->leaf_fullpath;
+	server->current_fullpath = mnt_ctx->leaf_fullpath;
+	mnt_ctx->origin_fullpath = mnt_ctx->leaf_fullpath = NULL;
+}
 
-	if (rc || !tcon || !ses)
+int cifs_mount(struct cifs_sb_info *cifs_sb, struct smb3_fs_context *ctx)
+{
+	int rc;
+	struct mount_ctx mnt_ctx = { .cifs_sb = cifs_sb, .fs_ctx = ctx, };
+	struct dfs_cache_tgt_list tl = DFS_CACHE_TGT_LIST_INIT(tl);
+	bool isdfs;
+
+	rc = is_dfs_mount(&mnt_ctx, &isdfs, &tl);
+	if (rc)
 		goto error;
+	if (!isdfs)
+		goto out;
 
-	kfree(ref_path);
-	/*
-	 * Store DFS full path in both superblock and tree connect structures.
-	 *
-	 * For DFS root mounts, the prefix path (cifs_sb->prepath) is preserved during reconnect so
-	 * only the root path is set in cifs_sb->origin_fullpath and tcon->dfs_path. And for DFS
-	 * links, the prefix path is included in both and may be changed during reconnect.  See
-	 * cifs_tree_connect().
-	 */
-	ref_path = dfs_cache_canonical_path(full_path, cifs_sb->local_nls, cifs_remap(cifs_sb));
-	kfree(full_path);
-	full_path = NULL;
+	uuid_gen(&mnt_ctx.mount_id);
+	rc = connect_dfs_root(&mnt_ctx, &tl);
+	dfs_cache_free_tgts(&tl);
 
-	if (IS_ERR(ref_path)) {
-		rc = PTR_ERR(ref_path);
-		ref_path = NULL;
+	if (rc)
 		goto error;
-	}
-	cifs_sb->origin_fullpath = ref_path;
 
-	ref_path = kstrdup(cifs_sb->origin_fullpath, GFP_KERNEL);
-	if (!ref_path) {
-		rc = -ENOMEM;
+	rc = is_path_remote(&mnt_ctx);
+	if (rc == -EREMOTE)
+		rc = follow_dfs_link(&mnt_ctx);
+	if (rc)
 		goto error;
-	}
-	spin_lock(&cifs_tcp_ses_lock);
-	tcon->dfs_path = ref_path;
-	ref_path = NULL;
-	spin_unlock(&cifs_tcp_ses_lock);
 
+	setup_server_referral_paths(&mnt_ctx);
 	/*
-	 * After reconnecting to a different server, unique ids won't
-	 * match anymore, so we disable serverino. This prevents
-	 * dentry revalidation to think the dentry are stale (ESTALE).
+	 * After reconnecting to a different server, unique ids won't match anymore, so we disable
+	 * serverino. This prevents dentry revalidation to think the dentry are stale (ESTALE).
 	 */
 	cifs_autodisable_serverino(cifs_sb);
 	/*
-	 * Force the use of prefix path to support failover on DFS paths that
-	 * resolve to targets that have different prefix paths.
+	 * Force the use of prefix path to support failover on DFS paths that resolve to targets
+	 * that have different prefix paths.
 	 */
 	cifs_sb->mnt_cifs_flags |= CIFS_MOUNT_USE_PREFIX_PATH;
 	kfree(cifs_sb->prepath);
 	cifs_sb->prepath = ctx->prepath;
 	ctx->prepath = NULL;
-	uuid_copy(&cifs_sb->dfs_mount_id, &mount_id);
+	uuid_copy(&cifs_sb->dfs_mount_id, &mnt_ctx.mount_id);
 
 out:
-	free_xid(xid);
-	cifs_try_adding_channels(cifs_sb, ses);
-	return mount_setup_tlink(cifs_sb, ses, tcon);
+	cifs_try_adding_channels(cifs_sb, mnt_ctx.ses);
+	rc = mount_setup_tlink(cifs_sb, mnt_ctx.ses, mnt_ctx.tcon);
+	if (rc)
+		goto error;
+
+	free_xid(mnt_ctx.xid);
+	return rc;
 
 error:
-	kfree(ref_path);
-	kfree(full_path);
-	kfree(cifs_sb->origin_fullpath);
-	dfs_cache_put_refsrv_sessions(&mount_id);
-	mount_put_conns(cifs_sb, xid, server, ses, tcon);
+	dfs_cache_put_refsrv_sessions(&mnt_ctx.mount_id);
+	kfree(mnt_ctx.origin_fullpath);
+	kfree(mnt_ctx.leaf_fullpath);
+	mount_put_conns(&mnt_ctx);
 	return rc;
 }
 #else
 int cifs_mount(struct cifs_sb_info *cifs_sb, struct smb3_fs_context *ctx)
 {
 	int rc = 0;
-	unsigned int xid;
-	struct cifs_ses *ses;
-	struct cifs_tcon *tcon;
-	struct TCP_Server_Info *server;
+	struct mount_ctx mnt_ctx = { .cifs_sb = cifs_sb, .fs_ctx = ctx, };
 
-	rc = mount_get_conns(ctx, cifs_sb, &xid, &server, &ses, &tcon);
+	rc = mount_get_conns(&mnt_ctx);
 	if (rc)
 		goto error;
 
-	if (tcon) {
-		rc = is_path_remote(cifs_sb, ctx, xid, server, tcon);
+	if (mnt_ctx.tcon) {
+		rc = is_path_remote(&mnt_ctx);
 		if (rc == -EREMOTE)
 			rc = -EOPNOTSUPP;
 		if (rc)
 			goto error;
 	}
 
-	free_xid(xid);
+	rc = mount_setup_tlink(cifs_sb, mnt_ctx.ses, mnt_ctx.tcon);
+	if (rc)
+		goto error;
 
-	return mount_setup_tlink(cifs_sb, ses, tcon);
+	free_xid(mnt_ctx.xid);
+	return rc;
 
 error:
-	mount_put_conns(cifs_sb, xid, server, ses, tcon);
+	mount_put_conns(&mnt_ctx);
 	return rc;
 }
 #endif
@@ -3687,12 +3683,11 @@
 	pSMB->AndXCommand = 0xFF;
 	pSMB->Flags = cpu_to_le16(TCON_EXTENDED_SECINFO);
 	bcc_ptr = &pSMB->Password[0];
-	if (tcon->pipe || (ses->server->sec_mode & SECMODE_USER)) {
-		pSMB->PasswordLength = cpu_to_le16(1);	/* minimum */
-		*bcc_ptr = 0; /* password is null byte */
-		bcc_ptr++;              /* skip password */
-		/* already aligned so no need to do it below */
-	}
+
+	pSMB->PasswordLength = cpu_to_le16(1);	/* minimum */
+	*bcc_ptr = 0; /* password is null byte */
+	bcc_ptr++;              /* skip password */
+	/* already aligned so no need to do it below */
 
 	if (ses->server->sign)
 		smb_buffer->Flags2 |= SMBFLG2_SECURITY_SIGNATURE;
@@ -3814,7 +3809,6 @@
 	kfree(cifs_sb->prepath);
 #ifdef CONFIG_CIFS_DFS_UPCALL
 	dfs_cache_put_refsrv_sessions(&cifs_sb->dfs_mount_id);
-	kfree(cifs_sb->origin_fullpath);
 #endif
 	call_rcu(&cifs_sb->rcu, delayed_free);
 }
@@ -4141,104 +4135,249 @@
 }
 
 #ifdef CONFIG_CIFS_DFS_UPCALL
-int cifs_tree_connect(const unsigned int xid, struct cifs_tcon *tcon, const struct nls_table *nlsc)
+static void mark_tcon_tcp_ses_for_reconnect(struct cifs_tcon *tcon)
+{
+	int i;
+
+	for (i = 0; i < tcon->ses->chan_count; i++) {
+		spin_lock(&GlobalMid_Lock);
+		if (tcon->ses->chans[i].server->tcpStatus != CifsExiting)
+			tcon->ses->chans[i].server->tcpStatus = CifsNeedReconnect;
+		spin_unlock(&GlobalMid_Lock);
+	}
+}
+
+/* Update dfs referral path of superblock */
+static int update_server_fullpath(struct TCP_Server_Info *server, struct cifs_sb_info *cifs_sb,
+				  const char *target)
+{
+	int rc = 0;
+	size_t len = strlen(target);
+	char *refpath, *npath;
+
+	if (unlikely(len < 2 || *target != '\\'))
+		return -EINVAL;
+
+	if (target[1] == '\\') {
+		len += 1;
+		refpath = kmalloc(len, GFP_KERNEL);
+		if (!refpath)
+			return -ENOMEM;
+
+		scnprintf(refpath, len, "%s", target);
+	} else {
+		len += sizeof("\\");
+		refpath = kmalloc(len, GFP_KERNEL);
+		if (!refpath)
+			return -ENOMEM;
+
+		scnprintf(refpath, len, "\\%s", target);
+	}
+
+	npath = dfs_cache_canonical_path(refpath, cifs_sb->local_nls, cifs_remap(cifs_sb));
+	kfree(refpath);
+
+	if (IS_ERR(npath)) {
+		rc = PTR_ERR(npath);
+	} else {
+		mutex_lock(&server->refpath_lock);
+		kfree(server->leaf_fullpath);
+		server->leaf_fullpath = npath;
+		mutex_unlock(&server->refpath_lock);
+		server->current_fullpath = server->leaf_fullpath;
+	}
+	return rc;
+}
+
+static int target_share_matches_server(struct TCP_Server_Info *server, const char *tcp_host,
+				       size_t tcp_host_len, char *share, bool *target_match)
+{
+	int rc = 0;
+	const char *dfs_host;
+	size_t dfs_host_len;
+
+	*target_match = true;
+	extract_unc_hostname(share, &dfs_host, &dfs_host_len);
+
+	/* Check if hostnames or addresses match */
+	if (dfs_host_len != tcp_host_len || strncasecmp(dfs_host, tcp_host, dfs_host_len) != 0) {
+		cifs_dbg(FYI, "%s: %.*s doesn't match %.*s\n", __func__, (int)dfs_host_len,
+			 dfs_host, (int)tcp_host_len, tcp_host);
+		rc = match_target_ip(server, dfs_host, dfs_host_len, target_match);
+		if (rc)
+			cifs_dbg(VFS, "%s: failed to match target ip: %d\n", __func__, rc);
+	}
+	return rc;
+}
+
+int __tree_connect_dfs_target(const unsigned int xid, struct cifs_tcon *tcon,
+			      struct cifs_sb_info *cifs_sb, char *tree,
+			      struct dfs_cache_tgt_list *tl, struct dfs_info3_param *ref)
 {
 	int rc;
 	struct TCP_Server_Info *server = tcon->ses->server;
 	const struct smb_version_operations *ops = server->ops;
-	struct dfs_cache_tgt_list tl;
-	struct dfs_cache_tgt_iterator *it = NULL;
-	char *tree;
+	struct cifs_tcon *ipc = tcon->ses->tcon_ipc;
+	bool islink;
+	char *share = NULL, *prefix = NULL;
 	const char *tcp_host;
 	size_t tcp_host_len;
-	const char *dfs_host;
-	size_t dfs_host_len;
-	char *share = NULL, *prefix = NULL;
-	struct dfs_info3_param ref = {0};
-	bool isroot;
+	struct dfs_cache_tgt_iterator *tit;
+	bool target_match;
 
-	tree = kzalloc(MAX_TREE_SIZE, GFP_KERNEL);
-	if (!tree)
-		return -ENOMEM;
+	extract_unc_hostname(server->hostname, &tcp_host, &tcp_host_len);
 
-	/* If it is not dfs or there was no cached dfs referral, then reconnect to same share */
-	if (!tcon->dfs_path || dfs_cache_noreq_find(tcon->dfs_path + 1, &ref, &tl)) {
-		if (tcon->ipc) {
-			scnprintf(tree, MAX_TREE_SIZE, "\\\\%s\\IPC$", server->hostname);
-			rc = ops->tree_connect(xid, tcon->ses, tree, tcon, nlsc);
-		} else {
-			rc = ops->tree_connect(xid, tcon->ses, tcon->treeName, tcon, nlsc);
-		}
+	islink = ref->server_type == DFS_TYPE_LINK;
+	free_dfs_info_param(ref);
+
+	tit = dfs_cache_get_tgt_iterator(tl);
+	if (!tit) {
+		rc = -ENOENT;
 		goto out;
 	}
 
-	isroot = ref.server_type == DFS_TYPE_ROOT;
-	free_dfs_info_param(&ref);
-
-	extract_unc_hostname(server->hostname, &tcp_host, &tcp_host_len);
-
-	for (it = dfs_cache_get_tgt_iterator(&tl); it; it = dfs_cache_get_next_tgt(&tl, it)) {
-		bool target_match;
+	/* Try to tree connect to all dfs targets */
+	for (; tit; tit = dfs_cache_get_next_tgt(tl, tit)) {
+		const char *target = dfs_cache_get_tgt_name(tit);
+		struct dfs_cache_tgt_list ntl = DFS_CACHE_TGT_LIST_INIT(ntl);
 
 		kfree(share);
 		kfree(prefix);
-		share = NULL;
-		prefix = NULL;
 
-		rc = dfs_cache_get_tgt_share(tcon->dfs_path + 1, it, &share, &prefix);
+		/* Check if share matches with tcp ses */
+		rc = dfs_cache_get_tgt_share(server->current_fullpath + 1, tit, &share, &prefix);
 		if (rc) {
-			cifs_dbg(VFS, "%s: failed to parse target share %d\n",
-				 __func__, rc);
-			continue;
+			cifs_dbg(VFS, "%s: failed to parse target share: %d\n", __func__, rc);
+			break;
 		}
 
-		extract_unc_hostname(share, &dfs_host, &dfs_host_len);
-
-		if (dfs_host_len != tcp_host_len
-		    || strncasecmp(dfs_host, tcp_host, dfs_host_len) != 0) {
-			cifs_dbg(FYI, "%s: %.*s doesn't match %.*s\n", __func__, (int)dfs_host_len,
-				 dfs_host, (int)tcp_host_len, tcp_host);
+		rc = target_share_matches_server(server, tcp_host, tcp_host_len, share,
+						 &target_match);
+		if (rc)
+			break;
+		if (!target_match) {
+			rc = -EHOSTUNREACH;
+			continue;
+		}
 
-			rc = match_target_ip(server, dfs_host, dfs_host_len, &target_match);
-			if (rc) {
-				cifs_dbg(VFS, "%s: failed to match target ip: %d\n", __func__, rc);
+		if (ipc->need_reconnect) {
+			scnprintf(tree, MAX_TREE_SIZE, "\\\\%s\\IPC$", server->hostname);
+			rc = ops->tree_connect(xid, ipc->ses, tree, ipc, cifs_sb->local_nls);
+			if (rc)
 				break;
-			}
+		}
 
-			if (!target_match) {
-				cifs_dbg(FYI, "%s: skipping target\n", __func__);
+		scnprintf(tree, MAX_TREE_SIZE, "\\%s", share);
+		if (!islink) {
+			rc = ops->tree_connect(xid, tcon->ses, tree, tcon, cifs_sb->local_nls);
+			break;
+		}
+		/*
+		 * If no dfs referrals were returned from link target, then just do a TREE_CONNECT
+		 * to it.  Otherwise, cache the dfs referral and then mark current tcp ses for
+		 * reconnect so either the demultiplex thread or the echo worker will reconnect to
+		 * newly resolved target.
+		 */
+		if (dfs_cache_find(xid, tcon->ses, cifs_sb->local_nls, cifs_remap(cifs_sb), target,
+				   ref, &ntl)) {
+			rc = ops->tree_connect(xid, tcon->ses, tree, tcon, cifs_sb->local_nls);
+			if (rc)
 				continue;
-			}
+			rc = dfs_cache_noreq_update_tgthint(server->current_fullpath + 1, tit);
+			if (!rc)
+				rc = cifs_update_super_prepath(cifs_sb, prefix);
+			break;
 		}
+		/* Target is another dfs share */
+		rc = update_server_fullpath(server, cifs_sb, target);
+		dfs_cache_free_tgts(tl);
 
-		if (tcon->ipc) {
-			scnprintf(tree, MAX_TREE_SIZE, "\\\\%s\\IPC$", share);
-			rc = ops->tree_connect(xid, tcon->ses, tree, tcon, nlsc);
+		if (!rc) {
+			rc = -EREMOTE;
+			list_replace_init(&ntl.tl_list, &tl->tl_list);
 		} else {
-			scnprintf(tree, MAX_TREE_SIZE, "\\%s", share);
-			rc = ops->tree_connect(xid, tcon->ses, tree, tcon, nlsc);
-			/* Only handle prefix paths of DFS link targets */
-			if (!rc && !isroot) {
-				rc = update_super_prepath(tcon, prefix);
-				break;
-			}
+			dfs_cache_free_tgts(&ntl);
+			free_dfs_info_param(ref);
 		}
-		if (rc == -EREMOTE)
-			break;
+		break;
 	}
 
+out:
 	kfree(share);
 	kfree(prefix);
 
-	if (!rc) {
-		if (it)
-			rc = dfs_cache_noreq_update_tgthint(tcon->dfs_path + 1, it);
-		else
-			rc = -ENOENT;
+	return rc;
+}
+
+int tree_connect_dfs_target(const unsigned int xid, struct cifs_tcon *tcon,
+			    struct cifs_sb_info *cifs_sb, char *tree,
+			    struct dfs_cache_tgt_list *tl, struct dfs_info3_param *ref)
+{
+	int rc;
+	int num_links = 0;
+	struct TCP_Server_Info *server = tcon->ses->server;
+
+	do {
+		rc = __tree_connect_dfs_target(xid, tcon, cifs_sb, tree, tl, ref);
+		if (!rc || rc != -EREMOTE)
+			break;
+	} while (rc = -ELOOP, ++num_links < MAX_NESTED_LINKS);
+	/*
+	 * If we couldn't tree connect to any targets from last referral path, then retry from
+	 * original referral path.
+	 */
+	if (rc && server->current_fullpath != server->origin_fullpath) {
+		server->current_fullpath = server->origin_fullpath;
+		mark_tcon_tcp_ses_for_reconnect(tcon);
 	}
-	dfs_cache_free_tgts(&tl);
+
+	dfs_cache_free_tgts(tl);
+	return rc;
+}
+
+int cifs_tree_connect(const unsigned int xid, struct cifs_tcon *tcon, const struct nls_table *nlsc)
+{
+	int rc;
+	struct TCP_Server_Info *server = tcon->ses->server;
+	const struct smb_version_operations *ops = server->ops;
+	struct super_block *sb = NULL;
+	struct cifs_sb_info *cifs_sb;
+	struct dfs_cache_tgt_list tl = DFS_CACHE_TGT_LIST_INIT(tl);
+	char *tree;
+	struct dfs_info3_param ref = {0};
+
+	tree = kzalloc(MAX_TREE_SIZE, GFP_KERNEL);
+	if (!tree)
+		return -ENOMEM;
+
+	if (tcon->ipc) {
+		scnprintf(tree, MAX_TREE_SIZE, "\\\\%s\\IPC$", server->hostname);
+		rc = ops->tree_connect(xid, tcon->ses, tree, tcon, nlsc);
+		goto out;
+	}
+
+	sb = cifs_get_tcp_super(server);
+	if (IS_ERR(sb)) {
+		rc = PTR_ERR(sb);
+		cifs_dbg(VFS, "%s: could not find superblock: %d\n", __func__, rc);
+		goto out;
+	}
+
+	cifs_sb = CIFS_SB(sb);
+
+	/* If it is not dfs or there was no cached dfs referral, then reconnect to same share */
+	if (!server->current_fullpath ||
+	    dfs_cache_noreq_find(server->current_fullpath + 1, &ref, &tl)) {
+		rc = ops->tree_connect(xid, tcon->ses, tcon->treeName, tcon, cifs_sb->local_nls);
+		goto out;
+	}
+
+	rc = tree_connect_dfs_target(xid, tcon, cifs_sb, tree, &tl, &ref);
+
 out:
 	kfree(tree);
+	cifs_put_tcp_super(sb);
+
 	return rc;
 }
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/dfs_cache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/dfs_cache.c
@@ -792,26 +792,27 @@
  */
 static int cache_refresh_path(const unsigned int xid, struct cifs_ses *ses, const char *path)
 {
-	int rc;
-	struct cache_entry *ce;
 	struct dfs_info3_param *refs = NULL;
+	struct cache_entry *ce;
 	int numrefs = 0;
-	bool newent = false;
+	int rc;
 
 	cifs_dbg(FYI, "%s: search path: %s\n", __func__, path);
 
-	down_write(&htable_rw_lock);
+	down_read(&htable_rw_lock);
 
 	ce = lookup_cache_entry(path);
-	if (!IS_ERR(ce)) {
-		if (!cache_entry_expired(ce)) {
-			dump_ce(ce);
-			up_write(&htable_rw_lock);
-			return 0;
-		}
-	} else {
-		newent = true;
+	if (!IS_ERR(ce) && !cache_entry_expired(ce)) {
+		up_read(&htable_rw_lock);
+		return 0;
 	}
+	/*
+	 * Unlock shared access as we don't want to hold any locks while getting
+	 * a new referral.  The @ses used for performing the I/O could be
+	 * reconnecting and it acquires @htable_rw_lock to look up the dfs cache
+	 * in order to failover -- if necessary.
+	 */
+	up_read(&htable_rw_lock);
 
 	/*
 	 * Either the entry was not found, or it is expired.
@@ -819,19 +820,22 @@
 	 */
 	rc = get_dfs_referral(xid, ses, path, &refs, &numrefs);
 	if (rc)
-		goto out_unlock;
+		goto out;
 
 	dump_refs(refs, numrefs);
 
-	if (!newent) {
-		rc = update_cache_entry_locked(ce, refs, numrefs);
-		goto out_unlock;
+	down_write(&htable_rw_lock);
+	/* Re-check as another task might have it added or refreshed already */
+	ce = lookup_cache_entry(path);
+	if (!IS_ERR(ce)) {
+		if (cache_entry_expired(ce))
+			rc = update_cache_entry_locked(ce, refs, numrefs);
+	} else {
+		rc = add_cache_entry_locked(refs, numrefs);
 	}
 
-	rc = add_cache_entry_locked(refs, numrefs);
-
-out_unlock:
 	up_write(&htable_rw_lock);
+out:
 	free_dfs_info_array(refs, numrefs);
 	return rc;
 }
@@ -1046,10 +1050,10 @@
 			     const struct nls_table *cp, int remap, const char *path,
 			     const struct dfs_cache_tgt_iterator *it)
 {
-	int rc;
-	const char *npath;
-	struct cache_entry *ce;
 	struct cache_dfs_tgt *t;
+	struct cache_entry *ce;
+	const char *npath;
+	int rc = 0;
 
 	npath = dfs_cache_canonical_path(path, cp, remap);
 	if (IS_ERR(npath))
@@ -1364,9 +1368,9 @@
 }
 
 /* Refresh dfs referral of tcon and mark it for reconnect if needed */
-static int refresh_tcon(struct cifs_ses **sessions, struct cifs_tcon *tcon, bool force_refresh)
+static int __refresh_tcon(const char *path, struct cifs_ses **sessions, struct cifs_tcon *tcon,
+			  bool force_refresh)
 {
-	const char *path = tcon->dfs_path + 1;
 	struct cifs_ses *ses;
 	struct cache_entry *ce;
 	struct dfs_info3_param *refs = NULL;
@@ -1422,6 +1426,20 @@
 	return rc;
 }
 
+static int refresh_tcon(struct cifs_ses **sessions, struct cifs_tcon *tcon, bool force_refresh)
+{
+	struct TCP_Server_Info *server = tcon->ses->server;
+
+	mutex_lock(&server->refpath_lock);
+	if (strcasecmp(server->leaf_fullpath, server->origin_fullpath))
+		__refresh_tcon(server->leaf_fullpath + 1, sessions, tcon, force_refresh);
+	mutex_unlock(&server->refpath_lock);
+
+	__refresh_tcon(server->origin_fullpath + 1, sessions, tcon, force_refresh);
+
+	return 0;
+}
+
 /**
  * dfs_cache_remount_fs - remount a DFS share
  *
@@ -1435,6 +1453,7 @@
 int dfs_cache_remount_fs(struct cifs_sb_info *cifs_sb)
 {
 	struct cifs_tcon *tcon;
+	struct TCP_Server_Info *server;
 	struct mount_group *mg;
 	struct cifs_ses *sessions[CACHE_MAX_ENTRIES + 1] = {NULL};
 	int rc;
@@ -1443,13 +1462,15 @@
 		return -EINVAL;
 
 	tcon = cifs_sb_master_tcon(cifs_sb);
-	if (!tcon->dfs_path) {
-		cifs_dbg(FYI, "%s: not a dfs tcon\n", __func__);
+	server = tcon->ses->server;
+
+	if (!server->origin_fullpath) {
+		cifs_dbg(FYI, "%s: not a dfs mount\n", __func__);
 		return 0;
 	}
 
 	if (uuid_is_null(&cifs_sb->dfs_mount_id)) {
-		cifs_dbg(FYI, "%s: tcon has no dfs mount group id\n", __func__);
+		cifs_dbg(FYI, "%s: no dfs mount group id\n", __func__);
 		return -EINVAL;
 	}
 
@@ -1457,7 +1478,7 @@
 	mg = find_mount_group_locked(&cifs_sb->dfs_mount_id);
 	if (IS_ERR(mg)) {
 		mutex_unlock(&mount_group_list_lock);
-		cifs_dbg(FYI, "%s: tcon has ipc session to refresh referral\n", __func__);
+		cifs_dbg(FYI, "%s: no ipc session for refreshing referral\n", __func__);
 		return PTR_ERR(mg);
 	}
 	kref_get(&mg->refcount);
@@ -1498,9 +1519,12 @@
 
 	spin_lock(&cifs_tcp_ses_lock);
 	list_for_each_entry(server, &cifs_tcp_ses_list, tcp_ses_list) {
+		if (!server->is_dfs_conn)
+			continue;
+
 		list_for_each_entry(ses, &server->smb_ses_list, smb_ses_list) {
 			list_for_each_entry(tcon, &ses->tcon_list, tcon_list) {
-				if (tcon->dfs_path) {
+				if (!tcon->ipc && !tcon->need_reconnect) {
 					tcon->tc_count++;
 					list_add_tail(&tcon->ulist, &tcons);
 				}
@@ -1510,8 +1534,16 @@
 	spin_unlock(&cifs_tcp_ses_lock);
 
 	list_for_each_entry_safe(tcon, ntcon, &tcons, ulist) {
+		struct TCP_Server_Info *server = tcon->ses->server;
+
 		list_del_init(&tcon->ulist);
-		refresh_tcon(sessions, tcon, false);
+
+		mutex_lock(&server->refpath_lock);
+		if (strcasecmp(server->leaf_fullpath, server->origin_fullpath))
+			__refresh_tcon(server->leaf_fullpath + 1, sessions, tcon, false);
+		mutex_unlock(&server->refpath_lock);
+
+		__refresh_tcon(server->origin_fullpath + 1, sessions, tcon, false);
 		cifs_put_tcon(tcon);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/dir.c
@@ -538,8 +538,10 @@
 	cifs_dbg(FYI, "cifs_create parent inode = 0x%p name is: %pd and dentry = 0x%p\n",
 		 inode, direntry, direntry);
 
-	if (unlikely(cifs_forced_shutdown(CIFS_SB(inode->i_sb))))
-		return -EIO;
+	if (unlikely(cifs_forced_shutdown(CIFS_SB(inode->i_sb)))) {
+		rc = -EIO;
+		goto out_free_xid;
+	}
 
 	tlink = cifs_sb_tlink(CIFS_SB(inode->i_sb));
 	rc = PTR_ERR(tlink);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/file.c
@@ -880,8 +880,8 @@
 		cfile = file->private_data;
 		file->private_data = NULL;
 		dclose = kmalloc(sizeof(struct cifs_deferred_close), GFP_KERNEL);
-		if ((cinode->oplock == CIFS_CACHE_RHW_FLG) &&
-		    cinode->lease_granted &&
+		if ((cifs_sb->ctx->closetimeo && cinode->oplock == CIFS_CACHE_RHW_FLG)
+		    && cinode->lease_granted &&
 		    !test_bit(CIFS_INO_CLOSE_ON_LOCK, &cinode->flags) &&
 		    dclose) {
 			if (test_and_clear_bit(CIFS_INO_MODIFIED_ATTR, &cinode->flags)) {
@@ -897,12 +897,12 @@
 				 * So, Increase the ref count to avoid use-after-free.
 				 */
 				if (!mod_delayed_work(deferredclose_wq,
-						&cfile->deferred, cifs_sb->ctx->acregmax))
+						&cfile->deferred, cifs_sb->ctx->closetimeo))
 					cifsFileInfo_get(cfile);
 			} else {
 				/* Deferred close for files */
 				queue_delayed_work(deferredclose_wq,
-						&cfile->deferred, cifs_sb->ctx->acregmax);
+						&cfile->deferred, cifs_sb->ctx->closetimeo);
 				cfile->deferred_close_scheduled = true;
 				spin_unlock(&cinode->deferred_lock);
 				return 0;
@@ -1806,11 +1806,13 @@
 	struct cifsFileInfo *cfile;
 	__u32 type;
 
-	rc = -EACCES;
 	xid = get_xid();
 
-	if (!(fl->fl_flags & FL_FLOCK))
-		return -ENOLCK;
+	if (!(fl->fl_flags & FL_FLOCK)) {
+		rc = -ENOLCK;
+		free_xid(xid);
+		return rc;
+	}
 
 	cfile = (struct cifsFileInfo *)file->private_data;
 	tcon = tlink_tcon(cfile->tlink);
@@ -1829,8 +1831,9 @@
 		 * if no lock or unlock then nothing to do since we do not
 		 * know what it is
 		 */
+		rc = -EOPNOTSUPP;
 		free_xid(xid);
-		return -EOPNOTSUPP;
+		return rc;
 	}
 
 	rc = cifs_setlk(file, fl, type, wait_flag, posix_lck, lock, unlock,
@@ -2692,12 +2695,23 @@
 	tcon = tlink_tcon(smbfile->tlink);
 	if (!(cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NOSSYNC)) {
 		server = tcon->ses->server;
-		if (server->ops->flush)
-			rc = server->ops->flush(xid, tcon, &smbfile->fid);
-		else
+		if (server->ops->flush == NULL) {
 			rc = -ENOSYS;
+			goto strict_fsync_exit;
+		}
+
+		if ((OPEN_FMODE(smbfile->f_flags) & FMODE_WRITE) == 0) {
+			smbfile = find_writable_file(CIFS_I(inode), FIND_WR_ANY);
+			if (smbfile) {
+				rc = server->ops->flush(xid, tcon, &smbfile->fid);
+				cifsFileInfo_put(smbfile);
+			} else
+				cifs_dbg(FYI, "ignore fsync for file not open for write\n");
+		} else
+			rc = server->ops->flush(xid, tcon, &smbfile->fid);
 	}
 
+strict_fsync_exit:
 	free_xid(xid);
 	return rc;
 }
@@ -2709,6 +2723,7 @@
 	struct cifs_tcon *tcon;
 	struct TCP_Server_Info *server;
 	struct cifsFileInfo *smbfile = file->private_data;
+	struct inode *inode = file_inode(file);
 	struct cifs_sb_info *cifs_sb = CIFS_FILE_SB(file);
 
 	rc = file_write_and_wait_range(file, start, end);
@@ -2725,12 +2740,23 @@
 	tcon = tlink_tcon(smbfile->tlink);
 	if (!(cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NOSSYNC)) {
 		server = tcon->ses->server;
-		if (server->ops->flush)
-			rc = server->ops->flush(xid, tcon, &smbfile->fid);
-		else
+		if (server->ops->flush == NULL) {
 			rc = -ENOSYS;
+			goto fsync_exit;
+		}
+
+		if ((OPEN_FMODE(smbfile->f_flags) & FMODE_WRITE) == 0) {
+			smbfile = find_writable_file(CIFS_I(inode), FIND_WR_ANY);
+			if (smbfile) {
+				rc = server->ops->flush(xid, tcon, &smbfile->fid);
+				cifsFileInfo_put(smbfile);
+			} else
+				cifs_dbg(FYI, "ignore fsync for file not open for write\n");
+		} else
+			rc = server->ops->flush(xid, tcon, &smbfile->fid);
 	}
 
+fsync_exit:
 	free_xid(xid);
 	return rc;
 }
@@ -3295,6 +3321,9 @@
 
 ssize_t cifs_direct_writev(struct kiocb *iocb, struct iov_iter *from)
 {
+	struct file *file = iocb->ki_filp;
+
+	cifs_revalidate_mapping(file->f_inode);
 	return __cifs_writev(iocb, from, true);
 }
 
@@ -3584,7 +3613,7 @@
 		rdata->got_bytes += result;
 	}
 
-	return rdata->got_bytes > 0 && result != -ECONNABORTED ?
+	return result != -ECONNABORTED && rdata->got_bytes > 0 ?
 						rdata->got_bytes : result;
 }
 
@@ -3711,6 +3740,11 @@
 				break;
 		}
 
+		if (cifs_sb->ctx->rsize == 0)
+			cifs_sb->ctx->rsize =
+				server->ops->negotiate_rsize(tlink_tcon(open_file->tlink),
+							     cifs_sb->ctx);
+
 		rc = server->ops->wait_mtu_credits(server, cifs_sb->ctx->rsize,
 						   &rsize, credits);
 		if (rc)
@@ -3984,6 +4018,15 @@
 		len = ctx->len;
 	}
 
+	if (direct) {
+		rc = filemap_write_and_wait_range(file->f_inode->i_mapping,
+						  offset, offset + len - 1);
+		if (rc) {
+			kref_put(&ctx->refcount, cifs_aio_ctx_release);
+			return -EAGAIN;
+		}
+	}
+
 	/* grab a lock here due to read response handlers can access ctx */
 	mutex_lock(&ctx->aio_mutex);
 
@@ -4345,7 +4388,7 @@
 		rdata->got_bytes += result;
 	}
 
-	return rdata->got_bytes > 0 && result != -ECONNABORTED ?
+	return result != -ECONNABORTED && rdata->got_bytes > 0 ?
 						rdata->got_bytes : result;
 }
 
@@ -4489,6 +4532,11 @@
 				break;
 		}
 
+		if (cifs_sb->ctx->rsize == 0)
+			cifs_sb->ctx->rsize =
+				server->ops->negotiate_rsize(tlink_tcon(open_file->tlink),
+							     cifs_sb->ctx);
+
 		rc = server->ops->wait_mtu_credits(server, cifs_sb->ctx->rsize,
 						   &rsize, credits);
 		if (rc)
@@ -4623,9 +4671,9 @@
 
 io_error:
 	kunmap(page);
-	unlock_page(page);
 
 read_complete:
+	unlock_page(page);
 	return rc;
 }
 
@@ -4817,17 +4865,25 @@
 	struct cifsFileInfo *cfile = container_of(work, struct cifsFileInfo,
 						  oplock_break);
 	struct inode *inode = d_inode(cfile->dentry);
+	struct cifs_sb_info *cifs_sb = CIFS_SB(inode->i_sb);
 	struct cifsInodeInfo *cinode = CIFS_I(inode);
-	struct cifs_tcon *tcon = tlink_tcon(cfile->tlink);
-	struct TCP_Server_Info *server = tcon->ses->server;
+	struct cifs_tcon *tcon;
+	struct TCP_Server_Info *server;
+	struct tcon_link *tlink;
 	int rc = 0;
-	bool purge_cache = false;
-	bool is_deferred = false;
-	struct cifs_deferred_close *dclose;
+	bool purge_cache = false, oplock_break_cancelled;
+	__u64 persistent_fid, volatile_fid;
+	__u16 net_fid;
 
 	wait_on_bit(&cinode->flags, CIFS_INODE_PENDING_WRITERS,
 			TASK_UNINTERRUPTIBLE);
 
+	tlink = cifs_sb_tlink(cifs_sb);
+	if (IS_ERR(tlink))
+		goto out;
+	tcon = tlink_tcon(tlink);
+	server = tcon->ses->server;
+
 	server->ops->downgrade_oplock(server, cinode, cfile->oplock_level,
 				      cfile->oplock_epoch, &purge_cache);
 
@@ -4864,30 +4920,32 @@
 	 * file handles but cached, then schedule deferred close immediately.
 	 * So, new open will not use cached handle.
 	 */
-	spin_lock(&CIFS_I(inode)->deferred_lock);
-	is_deferred = cifs_is_deferred_close(cfile, &dclose);
-	spin_unlock(&CIFS_I(inode)->deferred_lock);
-	if (is_deferred &&
-	    cfile->deferred_close_scheduled &&
-	    delayed_work_pending(&cfile->deferred)) {
-		if (cancel_delayed_work(&cfile->deferred)) {
-			_cifsFileInfo_put(cfile, false, false);
-			goto oplock_break_done;
-		}
-	}
+
+	if (!CIFS_CACHE_HANDLE(cinode) && !list_empty(&cinode->deferred_closes))
+		cifs_close_deferred_file(cinode);
+
+	persistent_fid = cfile->fid.persistent_fid;
+	volatile_fid = cfile->fid.volatile_fid;
+	net_fid = cfile->fid.netfid;
+	oplock_break_cancelled = cfile->oplock_break_cancelled;
+
+	_cifsFileInfo_put(cfile, false /* do not wait for ourself */, false);
 	/*
-	 * releasing stale oplock after recent reconnect of smb session using
-	 * a now incorrect file handle is not a data integrity issue but do
-	 * not bother sending an oplock release if session to server still is
-	 * disconnected since oplock already released by the server
-	 */
-	if (!cfile->oplock_break_cancelled) {
-		rc = tcon->ses->server->ops->oplock_response(tcon, &cfile->fid,
-							     cinode);
+	 * MS-SMB2 3.2.5.19.1 and 3.2.5.19.2 (and MS-CIFS 3.2.5.42) do not require
+	 * an acknowledgment to be sent when the file has already been closed.
+	 */
+	spin_lock(&cinode->open_file_lock);
+	/* check list empty since can race with kill_sb calling tree disconnect */
+	if (!oplock_break_cancelled && !list_empty(&cinode->openFileList)) {
+		spin_unlock(&cinode->open_file_lock);
+		rc = server->ops->oplock_response(tcon, persistent_fid,
+						  volatile_fid, net_fid, cinode);
 		cifs_dbg(FYI, "Oplock release rc = %d\n", rc);
-	}
-oplock_break_done:
-	_cifsFileInfo_put(cfile, false /* do not wait for ourself */, false);
+	} else
+		spin_unlock(&cinode->open_file_lock);
+
+	cifs_put_tlink(tlink);
+out:
 	cifs_done_oplock_break(cinode);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/fs_context.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/fs_context.c
@@ -65,6 +65,12 @@
 	{ Opt_sec_err, NULL }
 };
 
+static const match_table_t cifs_upcall_target = {
+	{ Opt_upcall_target_mount, "mount" },
+	{ Opt_upcall_target_application, "app" },
+	{ Opt_upcall_target_err, NULL }
+};
+
 const struct fs_parameter_spec smb3_fs_parameters[] = {
 	/* Mount options that take no arguments */
 	fsparam_flag_no("user_xattr", Opt_user_xattr),
@@ -143,10 +149,11 @@
 	fsparam_u32("actimeo", Opt_actimeo),
 	fsparam_u32("acdirmax", Opt_acdirmax),
 	fsparam_u32("acregmax", Opt_acregmax),
+	fsparam_u32("closetimeo", Opt_closetimeo),
 	fsparam_u32("echo_interval", Opt_echo_interval),
 	fsparam_u32("max_credits", Opt_max_credits),
 	fsparam_u32("handletimeout", Opt_handletimeout),
-	fsparam_u32("snapshot", Opt_snapshot),
+	fsparam_u64("snapshot", Opt_snapshot),
 	fsparam_u32("max_channels", Opt_max_channels),
 
 	/* Mount options which take string value */
@@ -167,6 +174,7 @@
 	fsparam_string("vers", Opt_vers),
 	fsparam_string("sec", Opt_sec),
 	fsparam_string("cache", Opt_cache),
+	fsparam_string("upcall_target", Opt_upcalltarget),
 
 	/* Arguments that should be ignored */
 	fsparam_flag("guest", Opt_ignore),
@@ -235,6 +243,29 @@
 	return 0;
 }
 
+static int
+cifs_parse_upcall_target(struct fs_context *fc, char *value, struct smb3_fs_context *ctx)
+{
+	substring_t args[MAX_OPT_ARGS];
+
+	ctx->upcall_target = UPTARGET_UNSPECIFIED;
+
+	switch (match_token(value, cifs_upcall_target, args)) {
+	case Opt_upcall_target_mount:
+		ctx->upcall_target = UPTARGET_MOUNT;
+		break;
+	case Opt_upcall_target_application:
+		ctx->upcall_target = UPTARGET_APP;
+		break;
+
+	default:
+		cifs_errorf(fc, "bad upcall target: %s\n", value);
+		return 1;
+	}
+
+	return 0;
+}
+
 static const match_table_t cifs_cacheflavor_tokens = {
 	{ Opt_cache_loose, "loose" },
 	{ Opt_cache_strict, "strict" },
@@ -307,6 +338,7 @@
 	new_ctx->nodename = NULL;
 	new_ctx->username = NULL;
 	new_ctx->password = NULL;
+	new_ctx->server_hostname = NULL;
 	new_ctx->domainname = NULL;
 	new_ctx->UNC = NULL;
 	new_ctx->source = NULL;
@@ -318,6 +350,7 @@
 	DUP_CTX_STR(mount_options);
 	DUP_CTX_STR(username);
 	DUP_CTX_STR(password);
+	DUP_CTX_STR(server_hostname);
 	DUP_CTX_STR(UNC);
 	DUP_CTX_STR(source);
 	DUP_CTX_STR(domainname);
@@ -430,6 +463,43 @@
 }
 
 /*
+ * Remove duplicate path delimiters. Windows is supposed to do that
+ * but there are some bugs that prevent rename from working if there are
+ * multiple delimiters.
+ *
+ * Returns a sanitized duplicate of @path. @gfp indicates the GFP_* flags
+ * for kstrdup.
+ * The caller is responsible for freeing the original.
+ */
+#define IS_DELIM(c) ((c) == '/' || (c) == '\\')
+char *cifs_sanitize_prepath(char *prepath, gfp_t gfp)
+{
+	char *cursor1 = prepath, *cursor2 = prepath;
+
+	/* skip all prepended delimiters */
+	while (IS_DELIM(*cursor1))
+		cursor1++;
+
+	/* copy the first letter */
+	*cursor2 = *cursor1;
+
+	/* copy the remainder... */
+	while (*(cursor1++)) {
+		/* ... skipping all duplicated delimiters */
+		if (IS_DELIM(*cursor1) && IS_DELIM(*cursor2))
+			continue;
+		*(++cursor2) = *cursor1;
+	}
+
+	/* if the last character is a delimiter, skip it */
+	if (IS_DELIM(*(cursor2 - 1)))
+		cursor2--;
+
+	*(cursor2) = '\0';
+	return kstrdup(prepath, gfp);
+}
+
+/*
  * Parse a devname into substrings and populate the ctx->UNC and ctx->prepath
  * fields with the result. Returns 0 on success and an error otherwise
  * (e.g. ENOMEM or EINVAL)
@@ -456,6 +526,12 @@
 	if (!pos)
 		return -EINVAL;
 
+	/* record the server hostname */
+	kfree(ctx->server_hostname);
+	ctx->server_hostname = kstrndup(devname + 2, pos - devname - 2, GFP_KERNEL);
+	if (!ctx->server_hostname)
+		return -ENOMEM;
+
 	/* skip past delimiter */
 	++pos;
 
@@ -482,7 +558,7 @@
 	if (!*pos)
 		return 0;
 
-	ctx->prepath = kstrdup(pos, GFP_KERNEL);
+	ctx->prepath = cifs_sanitize_prepath(pos, GFP_KERNEL);
 	if (!ctx->prepath)
 		return -ENOMEM;
 
@@ -626,6 +702,16 @@
 	/* set the port that we got earlier */
 	cifs_set_port((struct sockaddr *)&ctx->dstaddr, ctx->port);
 
+	if (ctx->uid_specified && !ctx->forceuid_specified) {
+		ctx->override_uid = 1;
+		pr_notice("enabling forceuid mount option implicitly because uid= option is specified\n");
+	}
+
+	if (ctx->gid_specified && !ctx->forcegid_specified) {
+		ctx->override_gid = 1;
+		pr_notice("enabling forcegid mount option implicitly because gid= option is specified\n");
+	}
+
 	if (ctx->override_uid && !ctx->uid_specified) {
 		ctx->override_uid = 0;
 		pr_notice("ignoring forceuid mount option specified with no uid= option\n");
@@ -838,6 +924,14 @@
 			ctx->sfu_remap = false; /* disable SFU mapping */
 		}
 		break;
+	case Opt_mapchars:
+		if (result.negated)
+			ctx->sfu_remap = false;
+		else {
+			ctx->sfu_remap = true;
+			ctx->remap = false; /* disable SFM (mapposix) mapping */
+		}
+		break;
 	case Opt_user_xattr:
 		if (result.negated)
 			ctx->no_xattr = 1;
@@ -849,12 +943,14 @@
 			ctx->override_uid = 0;
 		else
 			ctx->override_uid = 1;
+		ctx->forceuid_specified = true;
 		break;
 	case Opt_forcegid:
 		if (result.negated)
 			ctx->override_gid = 0;
 		else
 			ctx->override_gid = 1;
+		ctx->forcegid_specified = true;
 		break;
 	case Opt_perm:
 		if (result.negated)
@@ -989,21 +1085,21 @@
 		ctx->got_wsize = true;
 		break;
 	case Opt_acregmax:
-		ctx->acregmax = HZ * result.uint_32;
-		if (ctx->acregmax > CIFS_MAX_ACTIMEO) {
+		if (result.uint_32 > CIFS_MAX_ACTIMEO / HZ) {
 			cifs_errorf(fc, "acregmax too large\n");
 			goto cifs_parse_mount_err;
 		}
+		ctx->acregmax = HZ * result.uint_32;
 		break;
 	case Opt_acdirmax:
-		ctx->acdirmax = HZ * result.uint_32;
-		if (ctx->acdirmax > CIFS_MAX_ACTIMEO) {
+		if (result.uint_32 > CIFS_MAX_ACTIMEO / HZ) {
 			cifs_errorf(fc, "acdirmax too large\n");
 			goto cifs_parse_mount_err;
 		}
+		ctx->acdirmax = HZ * result.uint_32;
 		break;
 	case Opt_actimeo:
-		if (HZ * result.uint_32 > CIFS_MAX_ACTIMEO) {
+		if (result.uint_32 > CIFS_MAX_ACTIMEO / HZ) {
 			cifs_errorf(fc, "timeout too large\n");
 			goto cifs_parse_mount_err;
 		}
@@ -1014,11 +1110,18 @@
 		}
 		ctx->acdirmax = ctx->acregmax = HZ * result.uint_32;
 		break;
+	case Opt_closetimeo:
+		if (result.uint_32 > SMB3_MAX_DCLOSETIMEO / HZ) {
+			cifs_errorf(fc, "closetimeo too large\n");
+			goto cifs_parse_mount_err;
+		}
+		ctx->closetimeo = HZ * result.uint_32;
+		break;
 	case Opt_echo_interval:
 		ctx->echo_interval = result.uint_32;
 		break;
 	case Opt_snapshot:
-		ctx->snapshot_time = result.uint_32;
+		ctx->snapshot_time = result.uint_64;
 		break;
 	case Opt_max_credits:
 		if (result.uint_32 < 20 || result.uint_32 > 60000) {
@@ -1226,6 +1329,10 @@
 		if (cifs_parse_security_flavors(fc, param->string, ctx) != 0)
 			goto cifs_parse_mount_err;
 		break;
+	case Opt_upcalltarget:
+		if (cifs_parse_upcall_target(fc, param->string, ctx) != 0)
+			goto cifs_parse_mount_err;
+		break;
 	case Opt_cache:
 		if (cifs_parse_cache_flavor(fc, param->string, ctx) != 0)
 			goto cifs_parse_mount_err;
@@ -1392,6 +1499,11 @@
 	}
 	/* case Opt_ignore: - is ignored as expected ... */
 
+	if (ctx->multiuser && ctx->upcall_target == UPTARGET_MOUNT) {
+		cifs_errorf(fc, "multiuser mount option not supported with upcalltarget set as 'mount'\n");
+		goto cifs_parse_mount_err;
+	}
+
 	return 0;
 
  cifs_parse_mount_err:
@@ -1452,6 +1564,7 @@
 
 	ctx->acregmax = CIFS_DEF_ACTIMEO;
 	ctx->acdirmax = CIFS_DEF_ACTIMEO;
+	ctx->closetimeo = SMB3_DEF_DCLOSETIMEO;
 
 	/* Most clients set timeout to 0, allows server to use its default */
 	ctx->handle_timeout = 0; /* See MS-SMB2 spec section 2.2.14.2.12 */
@@ -1496,6 +1609,8 @@
 	ctx->username = NULL;
 	kfree_sensitive(ctx->password);
 	ctx->password = NULL;
+	kfree(ctx->server_hostname);
+	ctx->server_hostname = NULL;
 	kfree(ctx->UNC);
 	ctx->UNC = NULL;
 	kfree(ctx->source);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/fs_context.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/fs_context.h
@@ -54,6 +54,12 @@
 	Opt_sec_err
 };
 
+enum cifs_upcall_target_param {
+	Opt_upcall_target_mount,
+	Opt_upcall_target_application,
+	Opt_upcall_target_err
+};
+
 enum cifs_param {
 	/* Mount options that take no arguments */
 	Opt_user_xattr,
@@ -105,6 +111,8 @@
 	Opt_multichannel,
 	Opt_compress,
 	Opt_witness,
+	Opt_is_upcall_target_mount,
+	Opt_is_upcall_target_application,
 
 	/* Mount options which take numeric value */
 	Opt_backupuid,
@@ -123,6 +131,7 @@
 	Opt_actimeo,
 	Opt_acdirmax,
 	Opt_acregmax,
+	Opt_closetimeo,
 	Opt_echo_interval,
 	Opt_max_credits,
 	Opt_snapshot,
@@ -143,6 +152,7 @@
 	Opt_vers,
 	Opt_sec,
 	Opt_cache,
+	Opt_upcalltarget,
 
 	/* Mount options to be ignored */
 	Opt_ignore,
@@ -151,6 +161,8 @@
 };
 
 struct smb3_fs_context {
+	bool forceuid_specified;
+	bool forcegid_specified;
 	bool uid_specified;
 	bool cruid_specified;
 	bool gid_specified;
@@ -166,6 +178,7 @@
 	char *password;
 	char *domainname;
 	char *source;
+	char *server_hostname;
 	char *UNC;
 	char *nodename;
 	char *iocharset;  /* local code page for mapping to and from Unicode */
@@ -179,6 +192,7 @@
 	umode_t file_mode;
 	umode_t dir_mode;
 	enum securityEnum sectype; /* sectype requested via mnt opts */
+	enum upcall_target_enum upcall_target; /* where to upcall for mount */
 	bool sign; /* was signing requested via mnt opts? */
 	bool ignore_signature:1;
 	bool retry:1;
@@ -242,6 +256,8 @@
 	/* attribute cache timemout for files and directories in jiffies */
 	unsigned long acregmax;
 	unsigned long acdirmax;
+	/* timeout for deferred close of files in jiffies */
+	unsigned long closetimeo;
 	struct smb_version_operations *ops;
 	struct smb_version_values *vals;
 	char *prepath;
@@ -274,4 +290,12 @@
 extern int smb3_fs_context_dup(struct smb3_fs_context *new_ctx, struct smb3_fs_context *ctx);
 extern void smb3_update_mnt_flags(struct cifs_sb_info *cifs_sb);
 
+/*
+ * max deferred close timeout (jiffies) - 2^30
+ */
+#define SMB3_MAX_DCLOSETIMEO (1 << 30)
+#define SMB3_DEF_DCLOSETIMEO (1 * HZ) /* even 1 sec enough to help eg open/write/close/open/read */
+
+extern char *cifs_sanitize_prepath(char *prepath, gfp_t gfp);
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/inode.c
@@ -2531,7 +2531,7 @@
 	}
 
 	cifsFileInfo_put(cfile);
-	return -ENOTSUPP;
+	return -EOPNOTSUPP;
 }
 
 int cifs_truncate_page(struct address_space *mapping, loff_t from)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/ioctl.c
@@ -342,7 +342,7 @@
 					rc = put_user(ExtAttrBits &
 						FS_FL_USER_VISIBLE,
 						(int __user *)arg);
-				if (rc != EOPNOTSUPP)
+				if (rc != -EOPNOTSUPP)
 					break;
 			}
 #endif /* CONFIG_CIFS_POSIX */
@@ -371,7 +371,7 @@
 			 *		       pSMBFile->fid.netfid,
 			 *		       extAttrBits,
 			 *		       &ExtAttrMask);
-			 * if (rc != EOPNOTSUPP)
+			 * if (rc != -EOPNOTSUPP)
 			 *	break;
 			 */
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/link.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/link.c
@@ -85,6 +85,9 @@
 	if (rc != 1)
 		return -EINVAL;
 
+	if (link_len > CIFS_MF_SYMLINK_LINK_MAXLEN)
+		return -EINVAL;
+
 	rc = symlink_hash(link_len, link_str, md5_hash);
 	if (rc) {
 		cifs_dbg(FYI, "%s: MD5 hash failure: %d\n", __func__, rc);
@@ -456,6 +459,7 @@
 	oparms.disposition = FILE_CREATE;
 	oparms.fid = &fid;
 	oparms.reconnect = false;
+	oparms.mode = 0644;
 
 	rc = SMB2_open(xid, &oparms, utf16_path, &oplock, NULL, NULL,
 		       NULL, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/misc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/misc.c
@@ -75,6 +75,7 @@
 		INIT_LIST_HEAD(&ret_buf->tcon_list);
 		mutex_init(&ret_buf->session_mutex);
 		spin_lock_init(&ret_buf->iface_lock);
+		spin_lock_init(&ret_buf->chan_lock);
 	}
 	return ret_buf;
 }
@@ -138,9 +139,6 @@
 	kfree(buf_to_free->nativeFileSystem);
 	kfree_sensitive(buf_to_free->password);
 	kfree(buf_to_free->crfid.fid);
-#ifdef CONFIG_CIFS_DFS_UPCALL
-	kfree(buf_to_free->dfs_path);
-#endif
 	kfree(buf_to_free);
 }
 
@@ -342,6 +340,10 @@
 			cifs_dbg(VFS, "Length less than smb header size\n");
 		}
 		return -EIO;
+	} else if (total_read < sizeof(*smb) + 2 * smb->WordCount) {
+		cifs_dbg(VFS, "%s: can't read BCC due to invalid WordCount(%u)\n",
+			 __func__, smb->WordCount);
+		return -EIO;
 	}
 
 	/* otherwise, there is enough to get to the BCC */
@@ -735,6 +737,10 @@
 	list_for_each_entry(cfile, &cifs_inode->openFileList, flist) {
 		if (delayed_work_pending(&cfile->deferred)) {
 			if (cancel_delayed_work(&cfile->deferred)) {
+				spin_lock(&cifs_inode->deferred_lock);
+				cifs_del_deferred_close(cfile);
+				spin_unlock(&cifs_inode->deferred_lock);
+
 				tmp_list = kmalloc(sizeof(struct file_list), GFP_ATOMIC);
 				if (tmp_list == NULL)
 					break;
@@ -746,7 +752,7 @@
 	spin_unlock(&cifs_inode->open_file_lock);
 
 	list_for_each_entry_safe(tmp_list, tmp_next_list, &file_head, list) {
-		_cifsFileInfo_put(tmp_list->cfile, true, false);
+		_cifsFileInfo_put(tmp_list->cfile, false, false);
 		list_del(&tmp_list->list);
 		kfree(tmp_list);
 	}
@@ -766,6 +772,10 @@
 		cfile = list_entry(tmp, struct cifsFileInfo, tlist);
 		if (delayed_work_pending(&cfile->deferred)) {
 			if (cancel_delayed_work(&cfile->deferred)) {
+				spin_lock(&CIFS_I(d_inode(cfile->dentry))->deferred_lock);
+				cifs_del_deferred_close(cfile);
+				spin_unlock(&CIFS_I(d_inode(cfile->dentry))->deferred_lock);
+
 				tmp_list = kmalloc(sizeof(struct file_list), GFP_ATOMIC);
 				if (tmp_list == NULL)
 					break;
@@ -801,6 +811,10 @@
 		if (strstr(full_path, path)) {
 			if (delayed_work_pending(&cfile->deferred)) {
 				if (cancel_delayed_work(&cfile->deferred)) {
+					spin_lock(&CIFS_I(d_inode(cfile->dentry))->deferred_lock);
+					cifs_del_deferred_close(cfile);
+					spin_unlock(&CIFS_I(d_inode(cfile->dentry))->deferred_lock);
+
 					tmp_list = kmalloc(sizeof(struct file_list), GFP_ATOMIC);
 					if (tmp_list == NULL)
 						break;
@@ -1130,8 +1144,8 @@
  * @len: Where to store the length for this page:
  * @offset: Where to store the offset for this page
  */
-void rqst_page_get_length(struct smb_rqst *rqst, unsigned int page,
-				unsigned int *len, unsigned int *offset)
+void rqst_page_get_length(const struct smb_rqst *rqst, unsigned int page,
+			  unsigned int *len, unsigned int *offset)
 {
 	*len = rqst->rq_pagesz;
 	*offset = (page == 0) ? rqst->rq_offset : 0;
@@ -1211,18 +1225,23 @@
 		.data = data,
 		.sb = NULL,
 	};
+	struct file_system_type **fs_type = (struct file_system_type *[]) {
+		&cifs_fs_type, &smb3_fs_type, NULL,
+	};
 
-	iterate_supers_type(&cifs_fs_type, f, &sd);
-
-	if (!sd.sb)
-		return ERR_PTR(-EINVAL);
-	/*
-	 * Grab an active reference in order to prevent automounts (DFS links)
-	 * of expiring and then freeing up our cifs superblock pointer while
-	 * we're doing failover.
-	 */
-	cifs_sb_active(sd.sb);
-	return sd.sb;
+	for (; *fs_type; fs_type++) {
+		iterate_supers_type(*fs_type, f, &sd);
+		if (sd.sb) {
+			/*
+			 * Grab an active reference in order to prevent automounts (DFS links)
+			 * of expiring and then freeing up our cifs superblock pointer while
+			 * we're doing failover.
+			 */
+			cifs_sb_active(sd.sb);
+			return sd.sb;
+		}
+	}
+	return ERR_PTR(-EINVAL);
 }
 
 static void __cifs_put_super(struct super_block *sb)
@@ -1287,69 +1306,20 @@
 	return rc;
 }
 
-static void tcon_super_cb(struct super_block *sb, void *arg)
-{
-	struct super_cb_data *sd = arg;
-	struct cifs_tcon *tcon = sd->data;
-	struct cifs_sb_info *cifs_sb;
-
-	if (sd->sb)
-		return;
-
-	cifs_sb = CIFS_SB(sb);
-	if (tcon->dfs_path && cifs_sb->origin_fullpath &&
-	    !strcasecmp(tcon->dfs_path, cifs_sb->origin_fullpath))
-		sd->sb = sb;
-}
-
-static inline struct super_block *cifs_get_tcon_super(struct cifs_tcon *tcon)
-{
-	return __cifs_get_super(tcon_super_cb, tcon);
-}
-
-static inline void cifs_put_tcon_super(struct super_block *sb)
-{
-	__cifs_put_super(sb);
-}
-#else
-static inline struct super_block *cifs_get_tcon_super(struct cifs_tcon *tcon)
-{
-	return ERR_PTR(-EOPNOTSUPP);
-}
-
-static inline void cifs_put_tcon_super(struct super_block *sb)
+int cifs_update_super_prepath(struct cifs_sb_info *cifs_sb, char *prefix)
 {
-}
-#endif
-
-int update_super_prepath(struct cifs_tcon *tcon, char *prefix)
-{
-	struct super_block *sb;
-	struct cifs_sb_info *cifs_sb;
-	int rc = 0;
-
-	sb = cifs_get_tcon_super(tcon);
-	if (IS_ERR(sb))
-		return PTR_ERR(sb);
-
-	cifs_sb = CIFS_SB(sb);
-
 	kfree(cifs_sb->prepath);
 
 	if (prefix && *prefix) {
-		cifs_sb->prepath = kstrdup(prefix, GFP_ATOMIC);
-		if (!cifs_sb->prepath) {
-			rc = -ENOMEM;
-			goto out;
-		}
+		cifs_sb->prepath = cifs_sanitize_prepath(prefix, GFP_ATOMIC);
+		if (!cifs_sb->prepath)
+			return -ENOMEM;
 
 		convert_delimiter(cifs_sb->prepath, CIFS_DIR_SEP(cifs_sb));
 	} else
 		cifs_sb->prepath = NULL;
 
 	cifs_sb->mnt_cifs_flags |= CIFS_MOUNT_USE_PREFIX_PATH;
-
-out:
-	cifs_put_tcon_super(sb);
-	return rc;
+	return 0;
 }
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/sess.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/sess.c
@@ -54,32 +54,43 @@
 {
 	int i;
 
+	spin_lock(&ses->chan_lock);
 	for (i = 0; i < ses->chan_count; i++) {
-		if (is_server_using_iface(ses->chans[i].server, iface))
+		if (is_server_using_iface(ses->chans[i].server, iface)) {
+			spin_unlock(&ses->chan_lock);
 			return true;
+		}
 	}
+	spin_unlock(&ses->chan_lock);
 	return false;
 }
 
 /* returns number of channels added */
 int cifs_try_adding_channels(struct cifs_sb_info *cifs_sb, struct cifs_ses *ses)
 {
-	int old_chan_count = ses->chan_count;
-	int left = ses->chan_max - ses->chan_count;
+	int old_chan_count, new_chan_count;
+	int left;
 	int i = 0;
 	int rc = 0;
 	int tries = 0;
 	struct cifs_server_iface *ifaces = NULL;
 	size_t iface_count;
 
+	spin_lock(&ses->chan_lock);
+
+	new_chan_count = old_chan_count = ses->chan_count;
+	left = ses->chan_max - ses->chan_count;
+
 	if (left <= 0) {
 		cifs_dbg(FYI,
 			 "ses already at max_channels (%zu), nothing to open\n",
 			 ses->chan_max);
+		spin_unlock(&ses->chan_lock);
 		return 0;
 	}
 
 	if (ses->server->dialect < SMB30_PROT_ID) {
+		spin_unlock(&ses->chan_lock);
 		cifs_dbg(VFS, "multichannel is not supported on this protocol version, use 3.0 or above\n");
 		return 0;
 	}
@@ -87,8 +98,10 @@
 	if (!(ses->server->capabilities & SMB2_GLOBAL_CAP_MULTI_CHANNEL)) {
 		cifs_dbg(VFS, "server %s does not support multichannel\n", ses->server->hostname);
 		ses->chan_max = 1;
+		spin_unlock(&ses->chan_lock);
 		return 0;
 	}
+	spin_unlock(&ses->chan_lock);
 
 	/*
 	 * Make a copy of the iface list at the time and use that
@@ -142,10 +155,11 @@
 		cifs_dbg(FYI, "successfully opened new channel on iface#%d\n",
 			 i);
 		left--;
+		new_chan_count++;
 	}
 
 	kfree(ifaces);
-	return ses->chan_count - old_chan_count;
+	return new_chan_count - old_chan_count;
 }
 
 /*
@@ -157,10 +171,14 @@
 {
 	int i;
 
+	spin_lock(&ses->chan_lock);
 	for (i = 0; i < ses->chan_count; i++) {
-		if (ses->chans[i].server == server)
+		if (ses->chans[i].server == server) {
+			spin_unlock(&ses->chan_lock);
 			return &ses->chans[i];
+		}
 	}
+	spin_unlock(&ses->chan_lock);
 	return NULL;
 }
 
@@ -168,6 +186,7 @@
 cifs_ses_add_channel(struct cifs_sb_info *cifs_sb, struct cifs_ses *ses,
 		     struct cifs_server_iface *iface)
 {
+	struct TCP_Server_Info *chan_server;
 	struct cifs_chan *chan;
 	struct smb3_fs_context ctx = {NULL};
 	static const char unc_fmt[] = "\\%s\\foo";
@@ -240,15 +259,20 @@
 	       SMB2_CLIENT_GUID_SIZE);
 	ctx.use_client_guid = true;
 
-	mutex_lock(&ses->session_mutex);
+	chan_server = cifs_get_tcp_session(&ctx);
 
+	mutex_lock(&ses->session_mutex);
+	spin_lock(&ses->chan_lock);
 	chan = ses->binding_chan = &ses->chans[ses->chan_count];
-	chan->server = cifs_get_tcp_session(&ctx);
+	chan->server = chan_server;
 	if (IS_ERR(chan->server)) {
 		rc = PTR_ERR(chan->server);
 		chan->server = NULL;
+		spin_unlock(&ses->chan_lock);
 		goto out;
 	}
+	spin_unlock(&ses->chan_lock);
+
 	spin_lock(&cifs_tcp_ses_lock);
 	chan->server->is_channel = true;
 	spin_unlock(&cifs_tcp_ses_lock);
@@ -283,8 +307,11 @@
 	 * ses to the new server.
 	 */
 
+	spin_lock(&ses->chan_lock);
 	ses->chan_count++;
 	atomic_set(&ses->chan_seq, 0);
+	spin_unlock(&ses->chan_lock);
+
 out:
 	ses->binding = false;
 	ses->binding_chan = NULL;
@@ -293,6 +320,7 @@
 	if (rc && chan->server)
 		cifs_put_tcp_session(chan->server, 0);
 
+	free_xid(xid);
 	return rc;
 }
 
@@ -554,8 +582,8 @@
 {
 	unsigned int tioffset; /* challenge message target info area */
 	unsigned int tilen; /* challenge message target info area length  */
-
 	CHALLENGE_MESSAGE *pblob = (CHALLENGE_MESSAGE *)bcc_ptr;
+	__u32 server_flags;
 
 	if (blob_len < sizeof(CHALLENGE_MESSAGE)) {
 		cifs_dbg(VFS, "challenge blob len %d too small\n", blob_len);
@@ -573,12 +601,37 @@
 		return -EINVAL;
 	}
 
+	server_flags = le32_to_cpu(pblob->NegotiateFlags);
+	cifs_dbg(FYI, "%s: negotiate=0x%08x challenge=0x%08x\n", __func__,
+		 ses->ntlmssp->client_flags, server_flags);
+
+	if ((ses->ntlmssp->client_flags & (NTLMSSP_NEGOTIATE_SEAL | NTLMSSP_NEGOTIATE_SIGN)) &&
+	    (!(server_flags & NTLMSSP_NEGOTIATE_56) && !(server_flags & NTLMSSP_NEGOTIATE_128))) {
+		cifs_dbg(VFS, "%s: requested signing/encryption but server did not return either 56-bit or 128-bit session key size\n",
+			 __func__);
+		return -EINVAL;
+	}
+	if (!(server_flags & NTLMSSP_NEGOTIATE_NTLM) && !(server_flags & NTLMSSP_NEGOTIATE_EXTENDED_SEC)) {
+		cifs_dbg(VFS, "%s: server does not seem to support either NTLMv1 or NTLMv2\n", __func__);
+		return -EINVAL;
+	}
+	if (ses->server->sign && !(server_flags & NTLMSSP_NEGOTIATE_SIGN)) {
+		cifs_dbg(VFS, "%s: forced packet signing but server does not seem to support it\n",
+			 __func__);
+		return -EOPNOTSUPP;
+	}
+	if ((ses->ntlmssp->client_flags & NTLMSSP_NEGOTIATE_KEY_XCH) &&
+	    !(server_flags & NTLMSSP_NEGOTIATE_KEY_XCH))
+		pr_warn_once("%s: authentication has been weakened as server does not support key exchange\n",
+			     __func__);
+
+	ses->ntlmssp->server_flags = server_flags;
+
 	memcpy(ses->ntlmssp->cryptkey, pblob->Challenge, CIFS_CRYPTO_KEY_SIZE);
-	/* BB we could decode pblob->NegotiateFlags; some may be useful */
 	/* In particular we can examine sign flags */
 	/* BB spec says that if AvId field of MsvAvTimestamp is populated then
 		we must set the MIC field of the AUTHENTICATE_MESSAGE */
-	ses->ntlmssp->server_flags = le32_to_cpu(pblob->NegotiateFlags);
+
 	tioffset = le32_to_cpu(pblob->TargetInfoArray.BufferOffset);
 	tilen = le16_to_cpu(pblob->TargetInfoArray.Length);
 	if (tioffset > blob_len || tioffset + tilen > blob_len) {
@@ -618,12 +671,12 @@
 	flags = NTLMSSP_NEGOTIATE_56 |	NTLMSSP_REQUEST_TARGET |
 		NTLMSSP_NEGOTIATE_128 | NTLMSSP_NEGOTIATE_UNICODE |
 		NTLMSSP_NEGOTIATE_NTLM | NTLMSSP_NEGOTIATE_EXTENDED_SEC |
-		NTLMSSP_NEGOTIATE_SEAL;
-	if (server->sign)
-		flags |= NTLMSSP_NEGOTIATE_SIGN;
+		NTLMSSP_NEGOTIATE_ALWAYS_SIGN | NTLMSSP_NEGOTIATE_SEAL |
+		NTLMSSP_NEGOTIATE_SIGN;
 	if (!server->session_estab || ses->ntlmssp->sesskey_per_smbsess)
 		flags |= NTLMSSP_NEGOTIATE_KEY_XCH;
 
+	ses->ntlmssp->client_flags = flags;
 	sec_blob->NegotiateFlags = cpu_to_le32(flags);
 
 	sec_blob->WorkstationName.BufferOffset = 0;
@@ -682,15 +735,8 @@
 	memcpy(sec_blob->Signature, NTLMSSP_SIGNATURE, 8);
 	sec_blob->MessageType = NtLmAuthenticate;
 
-	flags = NTLMSSP_NEGOTIATE_56 |
-		NTLMSSP_REQUEST_TARGET | NTLMSSP_NEGOTIATE_TARGET_INFO |
-		NTLMSSP_NEGOTIATE_128 | NTLMSSP_NEGOTIATE_UNICODE |
-		NTLMSSP_NEGOTIATE_NTLM | NTLMSSP_NEGOTIATE_EXTENDED_SEC |
-		NTLMSSP_NEGOTIATE_SEAL;
-	if (ses->server->sign)
-		flags |= NTLMSSP_NEGOTIATE_SIGN;
-	if (!ses->server->session_estab || ses->ntlmssp->sesskey_per_smbsess)
-		flags |= NTLMSSP_NEGOTIATE_KEY_XCH;
+	flags = ses->ntlmssp->server_flags | NTLMSSP_REQUEST_TARGET |
+		NTLMSSP_NEGOTIATE_TARGET_INFO;
 
 	tmp = *pbuffer + sizeof(AUTHENTICATE_MESSAGE);
 	sec_blob->NegotiateFlags = cpu_to_le32(flags);
@@ -756,9 +802,9 @@
 	sec_blob->WorkstationName.MaximumLength = 0;
 	tmp += 2;
 
-	if (((ses->ntlmssp->server_flags & NTLMSSP_NEGOTIATE_KEY_XCH) ||
-		(ses->ntlmssp->server_flags & NTLMSSP_NEGOTIATE_EXTENDED_SEC))
-			&& !calc_seckey(ses)) {
+	if ((ses->ntlmssp->server_flags & NTLMSSP_NEGOTIATE_KEY_XCH) &&
+	    (!ses->server->session_estab || ses->ntlmssp->sesskey_per_smbsess) &&
+	    !calc_seckey(ses)) {
 		memcpy(tmp, ses->ntlmssp->ciphertext, CIFS_CPHTXT_SIZE);
 		sec_blob->SessionKey.BufferOffset = cpu_to_le32(tmp - *pbuffer);
 		sec_blob->SessionKey.Length = cpu_to_le16(CIFS_CPHTXT_SIZE);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb1ops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb1ops.c
@@ -864,12 +864,11 @@
 }
 
 static int
-cifs_oplock_response(struct cifs_tcon *tcon, struct cifs_fid *fid,
-		     struct cifsInodeInfo *cinode)
+cifs_oplock_response(struct cifs_tcon *tcon, __u64 persistent_fid,
+		__u64 volatile_fid, __u16 net_fid, struct cifsInodeInfo *cinode)
 {
-	return CIFSSMBLock(0, tcon, fid->netfid, current->tgid, 0, 0, 0, 0,
-			   LOCKING_ANDX_OPLOCK_RELEASE, false,
-			   CIFS_CACHE_READ(cinode) ? 1 : 0);
+	return CIFSSMBLock(0, tcon, net_fid, current->tgid, 0, 0, 0, 0,
+			   LOCKING_ANDX_OPLOCK_RELEASE, false, CIFS_CACHE_READ(cinode) ? 1 : 0);
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2file.c
@@ -61,7 +61,6 @@
 		nr_ioctl_req.Reserved = 0;
 		rc = SMB2_ioctl(xid, oparms->tcon, fid->persistent_fid,
 			fid->volatile_fid, FSCTL_LMR_REQUEST_RESILIENCY,
-			true /* is_fsctl */,
 			(char *)&nr_ioctl_req, sizeof(nr_ioctl_req),
 			CIFSMaxBufSize, NULL, NULL /* no return info */);
 		if (rc == -EOPNOTSUPP) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2inode.c
@@ -223,15 +223,32 @@
 		size[0] = 8; /* sizeof __le64 */
 		data[0] = ptr;
 
-		rc = SMB2_set_info_init(tcon, server,
-					&rqst[num_rqst], COMPOUND_FID,
-					COMPOUND_FID, current->tgid,
-					FILE_END_OF_FILE_INFORMATION,
-					SMB2_O_INFO_FILE, 0, data, size);
+		if (cfile) {
+			rc = SMB2_set_info_init(tcon, server,
+						&rqst[num_rqst],
+						cfile->fid.persistent_fid,
+						cfile->fid.volatile_fid,
+						current->tgid,
+						FILE_END_OF_FILE_INFORMATION,
+						SMB2_O_INFO_FILE, 0,
+						data, size);
+		} else {
+			rc = SMB2_set_info_init(tcon, server,
+						&rqst[num_rqst],
+						COMPOUND_FID,
+						COMPOUND_FID,
+						current->tgid,
+						FILE_END_OF_FILE_INFORMATION,
+						SMB2_O_INFO_FILE, 0,
+						data, size);
+			if (!rc) {
+				smb2_set_next_command(tcon, &rqst[num_rqst]);
+				smb2_set_related(&rqst[num_rqst]);
+			}
+		}
 		if (rc)
 			goto finished;
-		smb2_set_next_command(tcon, &rqst[num_rqst]);
-		smb2_set_related(&rqst[num_rqst++]);
+		num_rqst++;
 		trace_smb3_set_eof_enter(xid, ses->Suid, tcon->tid, full_path);
 		break;
 	case SMB2_OP_SET_INFO:
@@ -358,8 +375,6 @@
 	num_rqst++;
 
 	if (cfile) {
-		cifsFileInfo_put(cfile);
-		cfile = NULL;
 		rc = compound_send_recv(xid, ses, server,
 					flags, num_rqst - 2,
 					&rqst[1], &resp_buftype[1],
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2misc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2misc.c
@@ -113,7 +113,7 @@
 	} else if (nc_offset + 1 == non_ctxlen) {
 		cifs_dbg(FYI, "no SPNEGO security blob in negprot rsp\n");
 		size_of_pad_before_neg_ctxts = 0;
-	} else if (non_ctxlen == SMB311_NEGPROT_BASE_SIZE)
+	} else if (non_ctxlen == SMB311_NEGPROT_BASE_SIZE + 1)
 		/* has padding, but no SPNEGO blob */
 		size_of_pad_before_neg_ctxts = nc_offset - non_ctxlen + 1;
 	else
@@ -298,6 +298,9 @@
 char *
 smb2_get_data_area_len(int *off, int *len, struct smb2_sync_hdr *shdr)
 {
+	const int max_off = 4096;
+	const int max_len = 128 * 1024;
+
 	*off = 0;
 	*len = 0;
 
@@ -369,29 +372,20 @@
 	 * Invalid length or offset probably means data area is invalid, but
 	 * we have little choice but to ignore the data area in this case.
 	 */
-	if (*off > 4096) {
-		cifs_dbg(VFS, "offset %d too large, data area ignored\n", *off);
-		*len = 0;
-		*off = 0;
-	} else if (*off < 0) {
-		cifs_dbg(VFS, "negative offset %d to data invalid ignore data area\n",
-			 *off);
+	if (unlikely(*off < 0 || *off > max_off ||
+		     *len < 0 || *len > max_len)) {
+		cifs_dbg(VFS, "%s: invalid data area (off=%d len=%d)\n",
+			 __func__, *off, *len);
 		*off = 0;
 		*len = 0;
-	} else if (*len < 0) {
-		cifs_dbg(VFS, "negative data length %d invalid, data area ignored\n",
-			 *len);
-		*len = 0;
-	} else if (*len > 128 * 1024) {
-		cifs_dbg(VFS, "data area larger than 128K: %d\n", *len);
+	} else if (*off == 0) {
 		*len = 0;
 	}
 
 	/* return pointer to beginning of data area, ie offset from SMB start */
-	if ((*off != 0) && (*len != 0))
+	if (*off > 0 && *len > 0)
 		return (char *)shdr + *off;
-	else
-		return NULL;
+	return NULL;
 }
 
 /*
@@ -611,6 +605,8 @@
 	spin_lock(&cifs_tcp_ses_lock);
 	list_for_each_entry(server, &cifs_tcp_ses_list, tcp_ses_list) {
 		list_for_each_entry(ses, &server->smb_ses_list, smb_ses_list) {
+			if (cifs_ses_exiting(ses))
+				continue;
 			list_for_each_entry(tcon, &ses->tcon_list, tcon_list) {
 				spin_lock(&tcon->open_file_lock);
 				cifs_stats_inc(
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2ops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2ops.c
@@ -85,6 +85,7 @@
 		*val = 65000; /* Don't get near 64K credits, avoid srv bugs */
 		pr_warn_once("server overflowed SMB3 credits\n");
 	}
+	WARN_ON_ONCE(server->in_flight == 0);
 	server->in_flight--;
 	if (server->in_flight == 0 &&
 	   ((optype & CIFS_OP_MASK) != CIFS_NEG_OP) &&
@@ -266,7 +267,7 @@
 		cifs_server_dbg(VFS, "request has less credits (%d) than required (%d)",
 				credits->value, new_val);
 
-		return -ENOTSUPP;
+		return -EOPNOTSUPP;
 	}
 
 	spin_lock(&server->req_lock);
@@ -520,7 +521,7 @@
 
 	bytes_left = buf_len;
 	p = buf;
-	while (bytes_left >= sizeof(*p)) {
+	while (bytes_left >= (ssize_t)sizeof(*p)) {
 		nb_iface++;
 		next = le32_to_cpu(p->Next);
 		if (!next) {
@@ -555,7 +556,7 @@
 	info = *iface_list;
 	bytes_left = buf_len;
 	p = buf;
-	while (bytes_left >= sizeof(*p)) {
+	while (bytes_left >= (ssize_t)sizeof(*p)) {
 		info->speed = le64_to_cpu(p->LinkSpeed);
 		info->rdma_capable = le32_to_cpu(p->Capability & RDMA_CAPABLE) ? 1 : 0;
 		info->rss_capable = le32_to_cpu(p->Capability & RSS_CAPABLE) ? 1 : 0;
@@ -647,13 +648,13 @@
 	struct cifs_ses *ses = tcon->ses;
 
 	rc = SMB2_ioctl(xid, tcon, NO_FILE_ID, NO_FILE_ID,
-			FSCTL_QUERY_NETWORK_INTERFACE_INFO, true /* is_fsctl */,
+			FSCTL_QUERY_NETWORK_INTERFACE_INFO,
 			NULL /* no data input */, 0 /* no data input */,
 			CIFSMaxBufSize, (char **)&out_buf, &ret_data_len);
 	if (rc == -EOPNOTSUPP) {
 		cifs_dbg(FYI,
 			 "server does not support query network interfaces\n");
-		goto out;
+		ret_data_len = 0;
 	} else if (rc != 0) {
 		cifs_tcon_dbg(VFS, "error %d on ioctl to get interface list\n", rc);
 		goto out;
@@ -745,8 +746,8 @@
 		struct cifs_sb_info *cifs_sb,
 		struct cached_fid **cfid)
 {
-	struct cifs_ses *ses = tcon->ses;
-	struct TCP_Server_Info *server = ses->server;
+	struct cifs_ses *ses;
+	struct TCP_Server_Info *server;
 	struct cifs_open_parms oparms;
 	struct smb2_create_rsp *o_rsp = NULL;
 	struct smb2_query_info_rsp *qi_rsp = NULL;
@@ -764,6 +765,9 @@
 	if (tcon->nohandlecache)
 		return -ENOTSUPP;
 
+	ses = tcon->ses;
+	server = ses->server;
+
 	if (cifs_sb->root == NULL)
 		return -ENOENT;
 
@@ -882,8 +886,6 @@
 		goto oshr_exit;
 	}
 
-	atomic_inc(&tcon->num_remote_opens);
-
 	o_rsp = (struct smb2_create_rsp *)rsp_iov[0].iov_base;
 	oparms.fid->persistent_fid = o_rsp->PersistentFileId;
 	oparms.fid->volatile_fid = o_rsp->VolatileFileId;
@@ -893,8 +895,6 @@
 
 	tcon->crfid.tcon = tcon;
 	tcon->crfid.is_valid = true;
-	tcon->crfid.dentry = dentry;
-	dget(dentry);
 	kref_init(&tcon->crfid.refcount);
 
 	/* BB TBD check to see if oplock level check can be removed below */
@@ -903,12 +903,16 @@
 		 * See commit 2f94a3125b87. Increment the refcount when we
 		 * get a lease for root, release it if lease break occurs
 		 */
-		kref_get(&tcon->crfid.refcount);
-		tcon->crfid.has_lease = true;
-		smb2_parse_contexts(server, o_rsp,
+		rc = smb2_parse_contexts(server, rsp_iov,
 				&oparms.fid->epoch,
 				    oparms.fid->lease_key, &oplock,
 				    NULL, NULL);
+		if (rc)
+			goto oshr_exit;
+
+		if (!(oplock & SMB2_LEASE_READ_CACHING_HE))
+			goto oshr_exit;
+
 	} else
 		goto oshr_exit;
 
@@ -922,7 +926,10 @@
 				(char *)&tcon->crfid.file_all_info))
 		tcon->crfid.file_all_info_is_valid = true;
 	tcon->crfid.time = jiffies;
-
+	tcon->crfid.dentry = dentry;
+	dget(dentry);
+	kref_get(&tcon->crfid.refcount);
+	tcon->crfid.has_lease = true;
 
 oshr_exit:
 	mutex_unlock(&tcon->crfid.fid_mutex);
@@ -931,8 +938,15 @@
 	SMB2_query_info_free(&rqst[1]);
 	free_rsp_buf(resp_buftype[0], rsp_iov[0].iov_base);
 	free_rsp_buf(resp_buftype[1], rsp_iov[1].iov_base);
-	if (rc == 0)
+	if (rc) {
+		if (tcon->crfid.is_valid)
+			SMB2_close(0, tcon, oparms.fid->persistent_fid,
+				   oparms.fid->volatile_fid);
+	}
+	if (rc == 0) {
 		*cfid = &tcon->crfid;
+		atomic_inc(&tcon->num_remote_opens);
+	}
 	return rc;
 }
 
@@ -963,12 +977,13 @@
 	struct cifs_fid fid;
 	struct cached_fid *cfid = NULL;
 
-	oparms.tcon = tcon;
-	oparms.desired_access = FILE_READ_ATTRIBUTES;
-	oparms.disposition = FILE_OPEN;
-	oparms.create_options = cifs_create_options(cifs_sb, 0);
-	oparms.fid = &fid;
-	oparms.reconnect = false;
+	oparms = (struct cifs_open_parms) {
+		.tcon = tcon,
+		.desired_access = FILE_READ_ATTRIBUTES,
+		.disposition = FILE_OPEN,
+		.create_options = cifs_create_options(cifs_sb, 0),
+		.fid = &fid,
+	};
 
 	rc = open_cached_dir(xid, tcon, "", cifs_sb, &cfid);
 	if (rc == 0)
@@ -1102,9 +1117,7 @@
 	size_t name_len, value_len, user_name_len;
 
 	while (src_size > 0) {
-		name = &src->ea_data[0];
 		name_len = (size_t)src->ea_name_length;
-		value = &src->ea_data[src->ea_name_length + 1];
 		value_len = (size_t)le16_to_cpu(src->ea_value_length);
 
 		if (name_len == 0)
@@ -1116,6 +1129,9 @@
 			goto out;
 		}
 
+		name = &src->ea_data[0];
+		value = &src->ea_data[src->ea_name_length + 1];
+
 		if (ea_name) {
 			if (ea_name_len == name_len &&
 			    memcmp(ea_name, name, name_len) == 0) {
@@ -1303,7 +1319,7 @@
 			/* Use a fudge factor of 256 bytes in case we collide
 			 * with a different set_EAs command.
 			 */
-			if(CIFSMaxBufSize - MAX_SMB2_CREATE_RESPONSE_SIZE -
+			if (CIFSMaxBufSize - MAX_SMB2_CREATE_RESPONSE_SIZE -
 			   MAX_SMB2_CLOSE_RESPONSE_SIZE - 256 <
 			   used_len + ea_name_len + ea_value_len + 1) {
 				rc = -ENOSPC;
@@ -1357,6 +1373,8 @@
 				COMPOUND_FID, current->tgid,
 				FILE_FULL_EA_INFORMATION,
 				SMB2_O_INFO_FILE, 0, data, size);
+	if (rc)
+		goto sea_exit;
 	smb2_set_next_command(tcon, &rqst[1]);
 	smb2_set_related(&rqst[1]);
 
@@ -1367,6 +1385,8 @@
 	rqst[2].rq_nvec = 1;
 	rc = SMB2_close_init(tcon, server,
 			     &rqst[2], COMPOUND_FID, COMPOUND_FID, false);
+	if (rc)
+		goto sea_exit;
 	smb2_set_related(&rqst[2]);
 
 	rc = compound_send_recv(xid, ses, server,
@@ -1571,9 +1591,8 @@
 	struct resume_key_req *res_key;
 
 	rc = SMB2_ioctl(xid, tcon, persistent_fid, volatile_fid,
-			FSCTL_SRV_REQUEST_RESUME_KEY, true /* is_fsctl */,
-			NULL, 0 /* no input */, CIFSMaxBufSize,
-			(char **)&res_key, &ret_data_len);
+			FSCTL_SRV_REQUEST_RESUME_KEY, NULL, 0 /* no input */,
+			CIFSMaxBufSize, (char **)&res_key, &ret_data_len);
 
 	if (rc == -EOPNOTSUPP) {
 		pr_warn_once("Server share %s does not support copy range\n", tcon->treeName);
@@ -1631,6 +1650,7 @@
 	unsigned int size[2];
 	void *data[2];
 	int create_options = is_dir ? CREATE_NOT_FILE : CREATE_NOT_DIR;
+	void (*free_req1_func)(struct smb_rqst *r);
 
 	vars = kzalloc(sizeof(*vars), GFP_ATOMIC);
 	if (vars == NULL)
@@ -1640,27 +1660,29 @@
 
 	resp_buftype[0] = resp_buftype[1] = resp_buftype[2] = CIFS_NO_BUFFER;
 
-	if (copy_from_user(&qi, arg, sizeof(struct smb_query_info)))
-		goto e_fault;
-
+	if (copy_from_user(&qi, arg, sizeof(struct smb_query_info))) {
+		rc = -EFAULT;
+		goto free_vars;
+	}
 	if (qi.output_buffer_length > 1024) {
-		kfree(vars);
-		return -EINVAL;
+		rc = -EINVAL;
+		goto free_vars;
 	}
 
 	if (!ses || !server) {
-		kfree(vars);
-		return -EIO;
+		rc = -EIO;
+		goto free_vars;
 	}
 
 	if (smb3_encryption_required(tcon))
 		flags |= CIFS_TRANSFORM_REQ;
 
-	buffer = memdup_user(arg + sizeof(struct smb_query_info),
-			     qi.output_buffer_length);
-	if (IS_ERR(buffer)) {
-		kfree(vars);
-		return PTR_ERR(buffer);
+	if (qi.output_buffer_length) {
+		buffer = memdup_user(arg + sizeof(struct smb_query_info), qi.output_buffer_length);
+		if (IS_ERR(buffer)) {
+			rc = PTR_ERR(buffer);
+			goto free_vars;
+		}
 	}
 
 	/* Open */
@@ -1698,45 +1720,45 @@
 	rc = SMB2_open_init(tcon, server,
 			    &rqst[0], &oplock, &oparms, path);
 	if (rc)
-		goto iqinf_exit;
+		goto free_output_buffer;
 	smb2_set_next_command(tcon, &rqst[0]);
 
 	/* Query */
 	if (qi.flags & PASSTHRU_FSCTL) {
 		/* Can eventually relax perm check since server enforces too */
-		if (!capable(CAP_SYS_ADMIN))
+		if (!capable(CAP_SYS_ADMIN)) {
 			rc = -EPERM;
-		else  {
-			rqst[1].rq_iov = &vars->io_iov[0];
-			rqst[1].rq_nvec = SMB2_IOCTL_IOV_SIZE;
-
-			rc = SMB2_ioctl_init(tcon, server,
-					     &rqst[1],
-					     COMPOUND_FID, COMPOUND_FID,
-					     qi.info_type, true, buffer,
-					     qi.output_buffer_length,
-					     CIFSMaxBufSize -
-					     MAX_SMB2_CREATE_RESPONSE_SIZE -
-					     MAX_SMB2_CLOSE_RESPONSE_SIZE);
+			goto free_open_req;
 		}
+		rqst[1].rq_iov = &vars->io_iov[0];
+		rqst[1].rq_nvec = SMB2_IOCTL_IOV_SIZE;
+
+		rc = SMB2_ioctl_init(tcon, server, &rqst[1], COMPOUND_FID, COMPOUND_FID,
+				     qi.info_type, buffer, qi.output_buffer_length,
+				     CIFSMaxBufSize - MAX_SMB2_CREATE_RESPONSE_SIZE -
+				     MAX_SMB2_CLOSE_RESPONSE_SIZE);
+		free_req1_func = SMB2_ioctl_free;
 	} else if (qi.flags == PASSTHRU_SET_INFO) {
 		/* Can eventually relax perm check since server enforces too */
-		if (!capable(CAP_SYS_ADMIN))
+		if (!capable(CAP_SYS_ADMIN)) {
 			rc = -EPERM;
-		else  {
-			rqst[1].rq_iov = &vars->si_iov[0];
-			rqst[1].rq_nvec = 1;
-
-			size[0] = 8;
-			data[0] = buffer;
-
-			rc = SMB2_set_info_init(tcon, server,
-					&rqst[1],
-					COMPOUND_FID, COMPOUND_FID,
-					current->tgid,
-					FILE_END_OF_FILE_INFORMATION,
-					SMB2_O_INFO_FILE, 0, data, size);
+			goto free_open_req;
 		}
+		if (qi.output_buffer_length < 8) {
+			rc = -EINVAL;
+			goto free_open_req;
+		}
+		rqst[1].rq_iov = &vars->si_iov[0];
+		rqst[1].rq_nvec = 1;
+
+		/* MS-FSCC 2.4.13 FileEndOfFileInformation */
+		size[0] = 8;
+		data[0] = buffer;
+
+		rc = SMB2_set_info_init(tcon, server, &rqst[1], COMPOUND_FID, COMPOUND_FID,
+					current->tgid, FILE_END_OF_FILE_INFORMATION,
+					SMB2_O_INFO_FILE, 0, data, size);
+		free_req1_func = SMB2_set_info_free;
 	} else if (qi.flags == PASSTHRU_QUERY_INFO) {
 		rqst[1].rq_iov = &vars->qi_iov[0];
 		rqst[1].rq_nvec = 1;
@@ -1747,6 +1769,7 @@
 				  qi.info_type, qi.additional_information,
 				  qi.input_buffer_length,
 				  qi.output_buffer_length, buffer);
+		free_req1_func = SMB2_query_info_free;
 	} else { /* unknown flags */
 		cifs_tcon_dbg(VFS, "Invalid passthru query flags: 0x%x\n",
 			      qi.flags);
@@ -1754,7 +1777,7 @@
 	}
 
 	if (rc)
-		goto iqinf_exit;
+		goto free_open_req;
 	smb2_set_next_command(tcon, &rqst[1]);
 	smb2_set_related(&rqst[1]);
 
@@ -1765,14 +1788,14 @@
 	rc = SMB2_close_init(tcon, server,
 			     &rqst[2], COMPOUND_FID, COMPOUND_FID, false);
 	if (rc)
-		goto iqinf_exit;
+		goto free_req_1;
 	smb2_set_related(&rqst[2]);
 
 	rc = compound_send_recv(xid, ses, server,
 				flags, 3, rqst,
 				resp_buftype, rsp_iov);
 	if (rc)
-		goto iqinf_exit;
+		goto out;
 
 	/* No need to bump num_remote_opens since handle immediately closed */
 	if (qi.flags & PASSTHRU_FSCTL) {
@@ -1782,18 +1805,22 @@
 			qi.input_buffer_length = le32_to_cpu(io_rsp->OutputCount);
 		if (qi.input_buffer_length > 0 &&
 		    le32_to_cpu(io_rsp->OutputOffset) + qi.input_buffer_length
-		    > rsp_iov[1].iov_len)
-			goto e_fault;
+		    > rsp_iov[1].iov_len) {
+			rc = -EFAULT;
+			goto out;
+		}
 
 		if (copy_to_user(&pqi->input_buffer_length,
 				 &qi.input_buffer_length,
-				 sizeof(qi.input_buffer_length)))
-			goto e_fault;
+				 sizeof(qi.input_buffer_length))) {
+			rc = -EFAULT;
+			goto out;
+		}
 
 		if (copy_to_user((void __user *)pqi + sizeof(struct smb_query_info),
 				 (const void *)io_rsp + le32_to_cpu(io_rsp->OutputOffset),
 				 qi.input_buffer_length))
-			goto e_fault;
+			rc = -EFAULT;
 	} else {
 		pqi = (struct smb_query_info __user *)arg;
 		qi_rsp = (struct smb2_query_info_rsp *)rsp_iov[1].iov_base;
@@ -1801,28 +1828,30 @@
 			qi.input_buffer_length = le32_to_cpu(qi_rsp->OutputBufferLength);
 		if (copy_to_user(&pqi->input_buffer_length,
 				 &qi.input_buffer_length,
-				 sizeof(qi.input_buffer_length)))
-			goto e_fault;
+				 sizeof(qi.input_buffer_length))) {
+			rc = -EFAULT;
+			goto out;
+		}
 
 		if (copy_to_user(pqi + 1, qi_rsp->Buffer,
 				 qi.input_buffer_length))
-			goto e_fault;
+			rc = -EFAULT;
 	}
 
- iqinf_exit:
-	cifs_small_buf_release(rqst[0].rq_iov[0].iov_base);
-	cifs_small_buf_release(rqst[1].rq_iov[0].iov_base);
-	cifs_small_buf_release(rqst[2].rq_iov[0].iov_base);
+out:
 	free_rsp_buf(resp_buftype[0], rsp_iov[0].iov_base);
 	free_rsp_buf(resp_buftype[1], rsp_iov[1].iov_base);
 	free_rsp_buf(resp_buftype[2], rsp_iov[2].iov_base);
-	kfree(vars);
+	SMB2_close_free(&rqst[2]);
+free_req_1:
+	free_req1_func(&rqst[1]);
+free_open_req:
+	SMB2_open_free(&rqst[0]);
+free_output_buffer:
 	kfree(buffer);
+free_vars:
+	kfree(vars);
 	return rc;
-
-e_fault:
-	rc = -EFAULT;
-	goto iqinf_exit;
 }
 
 static ssize_t
@@ -1839,9 +1868,17 @@
 	int chunks_copied = 0;
 	bool chunk_sizes_updated = false;
 	ssize_t bytes_written, total_bytes_written = 0;
+	struct inode *inode;
 
 	pcchunk = kmalloc(sizeof(struct copychunk_ioctl), GFP_KERNEL);
 
+	/*
+	 * We need to flush all unwritten data before we can send the
+	 * copychunk ioctl to the server.
+	 */
+	inode = d_inode(trgtfile->dentry);
+	filemap_write_and_wait(inode->i_mapping);
+
 	if (pcchunk == NULL)
 		return -ENOMEM;
 
@@ -1866,16 +1903,15 @@
 		pcchunk->SourceOffset = cpu_to_le64(src_off);
 		pcchunk->TargetOffset = cpu_to_le64(dest_off);
 		pcchunk->Length =
-			cpu_to_le32(min_t(u32, len, tcon->max_bytes_chunk));
+			cpu_to_le32(min_t(u64, len, tcon->max_bytes_chunk));
 
 		/* Request server copy to target from src identified by key */
 		kfree(retbuf);
 		retbuf = NULL;
 		rc = SMB2_ioctl(xid, tcon, trgtfile->fid.persistent_fid,
 			trgtfile->fid.volatile_fid, FSCTL_SRV_COPYCHUNK_WRITE,
-			true /* is_fsctl */, (char *)pcchunk,
-			sizeof(struct copychunk_ioctl),	CIFSMaxBufSize,
-			(char **)&retbuf, &ret_data_len);
+			(char *)pcchunk, sizeof(struct copychunk_ioctl),
+			CIFSMaxBufSize, (char **)&retbuf, &ret_data_len);
 		if (rc == 0) {
 			if (ret_data_len !=
 					sizeof(struct copychunk_ioctl_rsp)) {
@@ -2035,7 +2071,6 @@
 
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid, FSCTL_SET_SPARSE,
-			true /* is_fctl */,
 			&setsparse, 1, CIFSMaxBufSize, NULL, NULL);
 	if (rc) {
 		tcon->broken_sparse_sup = true;
@@ -2118,7 +2153,6 @@
 	rc = SMB2_ioctl(xid, tcon, trgtfile->fid.persistent_fid,
 			trgtfile->fid.volatile_fid,
 			FSCTL_DUPLICATE_EXTENTS_TO_FILE,
-			true /* is_fsctl */,
 			(char *)&dup_ext_buf,
 			sizeof(struct duplicate_extents_to_file),
 			CIFSMaxBufSize, NULL,
@@ -2153,7 +2187,6 @@
 	return SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid,
 			FSCTL_SET_INTEGRITY_INFORMATION,
-			true /* is_fsctl */,
 			(char *)&integr_info,
 			sizeof(struct fsctl_set_integrity_information_req),
 			CIFSMaxBufSize, NULL,
@@ -2206,7 +2239,6 @@
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid,
 			FSCTL_SRV_ENUMERATE_SNAPSHOTS,
-			true /* is_fsctl */,
 			NULL, 0 /* no input data */, max_response_size,
 			(char **)&retbuf,
 			&ret_data_len);
@@ -2543,15 +2575,14 @@
 }
 
 static int
-smb2_oplock_response(struct cifs_tcon *tcon, struct cifs_fid *fid,
-		     struct cifsInodeInfo *cinode)
+smb2_oplock_response(struct cifs_tcon *tcon, __u64 persistent_fid,
+		__u64 volatile_fid, __u16 net_fid, struct cifsInodeInfo *cinode)
 {
 	if (tcon->ses->server->capabilities & SMB2_GLOBAL_CAP_LEASING)
 		return SMB2_lease_break(0, tcon, cinode->lease_key,
 					smb2_get_lease_state(cinode));
 
-	return SMB2_oplock_break(0, tcon, fid->persistent_fid,
-				 fid->volatile_fid,
+	return SMB2_oplock_break(0, tcon, persistent_fid, volatile_fid,
 				 CIFS_CACHE_READ(cinode) ? 1 : 0);
 }
 
@@ -2843,6 +2874,7 @@
 	struct fsctl_get_dfs_referral_req *dfs_req = NULL;
 	struct get_dfs_referral_rsp *dfs_rsp = NULL;
 	u32 dfs_req_size = 0, dfs_rsp_size = 0;
+	int retry_count = 0;
 
 	cifs_dbg(FYI, "%s: path: %s\n", __func__, search_name);
 
@@ -2891,14 +2923,18 @@
 	do {
 		rc = SMB2_ioctl(xid, tcon, NO_FILE_ID, NO_FILE_ID,
 				FSCTL_DFS_GET_REFERRALS,
-				true /* is_fsctl */,
 				(char *)dfs_req, dfs_req_size, CIFSMaxBufSize,
 				(char **)&dfs_rsp, &dfs_rsp_size);
-	} while (rc == -EAGAIN);
+		if (!is_retryable_error(rc))
+			break;
+		usleep_range(512, 2048);
+	} while (++retry_count < 5);
 
+	if (!rc && !dfs_rsp)
+		rc = -EIO;
 	if (rc) {
-		if ((rc != -ENOENT) && (rc != -EOPNOTSUPP))
-			cifs_tcon_dbg(VFS, "ioctl error in %s rc=%d\n", __func__, rc);
+		if (!is_retryable_error(rc) && rc != -ENOENT && rc != -EOPNOTSUPP)
+			cifs_tcon_dbg(VFS, "%s: ioctl error: rc=%d\n", __func__, rc);
 		goto out;
 	}
 
@@ -2935,6 +2971,12 @@
 
 	/* See MS-FSCC 2.1.2.6 for the 'NFS' style reparse tags */
 	len = le16_to_cpu(symlink_buf->ReparseDataLength);
+	if (len < sizeof(symlink_buf->InodeType)) {
+		cifs_dbg(VFS, "srv returned malformed nfs buffer\n");
+		return -EIO;
+	}
+
+	len -= sizeof(symlink_buf->InodeType);
 
 	if (le64_to_cpu(symlink_buf->InodeType) != NFS_SPECFILE_LNK) {
 		cifs_dbg(VFS, "%lld not a supported symlink type\n",
@@ -3095,8 +3137,7 @@
 
 	rc = SMB2_ioctl_init(tcon, server,
 			     &rqst[1], fid.persistent_fid,
-			     fid.volatile_fid, FSCTL_GET_REPARSE_POINT,
-			     true /* is_fctl */, NULL, 0,
+			     fid.volatile_fid, FSCTL_GET_REPARSE_POINT, NULL, 0,
 			     CIFSMaxBufSize -
 			     MAX_SMB2_CREATE_RESPONSE_SIZE -
 			     MAX_SMB2_CLOSE_RESPONSE_SIZE);
@@ -3231,7 +3272,7 @@
 	struct kvec close_iov[1];
 	struct smb2_ioctl_rsp *ioctl_rsp;
 	struct reparse_data_buffer *reparse_buf;
-	u32 plen;
+	u32 off, count, len;
 
 	cifs_dbg(FYI, "%s: path: %s\n", __func__, full_path);
 
@@ -3276,8 +3317,7 @@
 
 	rc = SMB2_ioctl_init(tcon, server,
 			     &rqst[1], COMPOUND_FID,
-			     COMPOUND_FID, FSCTL_GET_REPARSE_POINT,
-			     true /* is_fctl */, NULL, 0,
+			     COMPOUND_FID, FSCTL_GET_REPARSE_POINT, NULL, 0,
 			     CIFSMaxBufSize -
 			     MAX_SMB2_CREATE_RESPONSE_SIZE -
 			     MAX_SMB2_CLOSE_RESPONSE_SIZE);
@@ -3311,16 +3351,22 @@
 	 */
 	if (rc == 0) {
 		/* See MS-FSCC 2.3.23 */
+		off = le32_to_cpu(ioctl_rsp->OutputOffset);
+		count = le32_to_cpu(ioctl_rsp->OutputCount);
+		if (check_add_overflow(off, count, &len) ||
+		    len > rsp_iov[1].iov_len) {
+			cifs_tcon_dbg(VFS, "%s: invalid ioctl: off=%d count=%d\n",
+				      __func__, off, count);
+			rc = -EIO;
+			goto query_rp_exit;
+		}
 
-		reparse_buf = (struct reparse_data_buffer *)
-			((char *)ioctl_rsp +
-			 le32_to_cpu(ioctl_rsp->OutputOffset));
-		plen = le32_to_cpu(ioctl_rsp->OutputCount);
-
-		if (plen + le32_to_cpu(ioctl_rsp->OutputOffset) >
-		    rsp_iov[1].iov_len) {
-			cifs_tcon_dbg(FYI, "srv returned invalid ioctl len: %d\n",
-				 plen);
+		reparse_buf = (void *)((u8 *)ioctl_rsp + off);
+		len = sizeof(*reparse_buf);
+		if (count < len ||
+		    count < le16_to_cpu(reparse_buf->ReparseDataLength) + len) {
+			cifs_tcon_dbg(VFS, "%s: invalid ioctl: off=%d count=%d\n",
+				      __func__, off, count);
 			rc = -EIO;
 			goto query_rp_exit;
 		}
@@ -3547,7 +3593,7 @@
 	fsctl_buf.BeyondFinalZero = cpu_to_le64(offset + len);
 
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
-			cfile->fid.volatile_fid, FSCTL_SET_ZERO_DATA, true,
+			cfile->fid.volatile_fid, FSCTL_SET_ZERO_DATA,
 			(char *)&fsctl_buf,
 			sizeof(struct file_zero_data_information),
 			0, NULL, NULL);
@@ -3577,7 +3623,7 @@
 static long smb3_punch_hole(struct file *file, struct cifs_tcon *tcon,
 			    loff_t offset, loff_t len)
 {
-	struct inode *inode;
+	struct inode *inode = file_inode(file);
 	struct cifsFileInfo *cfile = file->private_data;
 	struct file_zero_data_information fsctl_buf;
 	long rc;
@@ -3586,14 +3632,12 @@
 
 	xid = get_xid();
 
-	inode = d_inode(cfile->dentry);
-
+	inode_lock(inode);
 	/* Need to make file sparse, if not already, before freeing range. */
 	/* Consider adding equivalent for compressed since it could also work */
 	if (!smb2_set_sparse(xid, tcon, cfile, inode, set_sparse)) {
 		rc = -EOPNOTSUPP;
-		free_xid(xid);
-		return rc;
+		goto out;
 	}
 
 	filemap_invalidate_lock(inode->i_mapping);
@@ -3610,11 +3654,13 @@
 
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid, FSCTL_SET_ZERO_DATA,
-			true /* is_fctl */, (char *)&fsctl_buf,
+			(char *)&fsctl_buf,
 			sizeof(struct file_zero_data_information),
 			CIFSMaxBufSize, NULL, NULL);
-	free_xid(xid);
 	filemap_invalidate_unlock(inode->i_mapping);
+out:
+	inode_unlock(inode);
+	free_xid(xid);
 	return rc;
 }
 
@@ -3670,7 +3716,7 @@
 	in_data.length = cpu_to_le64(len);
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid,
-			FSCTL_QUERY_ALLOCATED_RANGES, true,
+			FSCTL_QUERY_ALLOCATED_RANGES,
 			(char *)&in_data, sizeof(in_data),
 			1024 * sizeof(struct file_allocated_range_buffer),
 			(char **)&out_data, &out_data_len);
@@ -3773,7 +3819,7 @@
 		if (rc)
 			goto out;
 
-		if ((cifsi->cifsAttrs & FILE_ATTRIBUTE_SPARSE_FILE) == 0)
+		if (cifsi->cifsAttrs & FILE_ATTRIBUTE_SPARSE_FILE)
 			smb2_set_sparse(xid, tcon, cfile, inode, false);
 
 		eof = cpu_to_le64(off + len);
@@ -3982,7 +4028,7 @@
 
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid,
-			FSCTL_QUERY_ALLOCATED_RANGES, true,
+			FSCTL_QUERY_ALLOCATED_RANGES,
 			(char *)&in_data, sizeof(in_data),
 			sizeof(struct file_allocated_range_buffer),
 			(char **)&out_data, &out_data_len);
@@ -4042,7 +4088,7 @@
 
 	rc = SMB2_ioctl(xid, tcon, cfile->fid.persistent_fid,
 			cfile->fid.volatile_fid,
-			FSCTL_QUERY_ALLOCATED_RANGES, true,
+			FSCTL_QUERY_ALLOCATED_RANGES,
 			(char *)&in_data, sizeof(in_data),
 			1024 * sizeof(struct file_allocated_range_buffer),
 			(char **)&out_data, &out_data_len);
@@ -4250,11 +4296,13 @@
 	}
 }
 
+#ifdef CONFIG_CIFS_ALLOW_INSECURE_LEGACY
 static bool
 smb2_is_read_op(__u32 oplock)
 {
 	return oplock == SMB2_OPLOCK_LEVEL_II;
 }
+#endif /* CIFS_ALLOW_INSECURE_LEGACY */
 
 static bool
 smb21_is_read_op(__u32 oplock)
@@ -4384,69 +4432,82 @@
 	memcpy(&tr_hdr->SessionId, &shdr->SessionId, 8);
 }
 
-/* We can not use the normal sg_set_buf() as we will sometimes pass a
- * stack object as buf.
- */
-static inline void smb2_sg_set_buf(struct scatterlist *sg, const void *buf,
-				   unsigned int buflen)
+static void *smb2_aead_req_alloc(struct crypto_aead *tfm, const struct smb_rqst *rqst,
+				 int num_rqst, const u8 *sig, u8 **iv,
+				 struct aead_request **req, struct scatterlist **sgl,
+				 unsigned int *num_sgs)
 {
-	void *addr;
-	/*
-	 * VMAP_STACK (at least) puts stack into the vmalloc address space
-	 */
-	if (is_vmalloc_addr(buf))
-		addr = vmalloc_to_page(buf);
-	else
-		addr = virt_to_page(buf);
-	sg_set_page(sg, addr, buflen, offset_in_page(buf));
+	unsigned int req_size = sizeof(**req) + crypto_aead_reqsize(tfm);
+	unsigned int iv_size = crypto_aead_ivsize(tfm);
+	unsigned int len;
+	u8 *p;
+
+	*num_sgs = cifs_get_num_sgs(rqst, num_rqst, sig);
+
+	len = iv_size;
+	len += crypto_aead_alignmask(tfm) & ~(crypto_tfm_ctx_alignment() - 1);
+	len = ALIGN(len, crypto_tfm_ctx_alignment());
+	len += req_size;
+	len = ALIGN(len, __alignof__(struct scatterlist));
+	len += *num_sgs * sizeof(**sgl);
+
+	p = kmalloc(len, GFP_ATOMIC);
+	if (!p)
+		return NULL;
+
+	*iv = (u8 *)PTR_ALIGN(p, crypto_aead_alignmask(tfm) + 1);
+	*req = (struct aead_request *)PTR_ALIGN(*iv + iv_size,
+						crypto_tfm_ctx_alignment());
+	*sgl = (struct scatterlist *)PTR_ALIGN((u8 *)*req + req_size,
+					       __alignof__(struct scatterlist));
+	return p;
 }
 
-/* Assumes the first rqst has a transform header as the first iov.
- * I.e.
- * rqst[0].rq_iov[0]  is transform header
- * rqst[0].rq_iov[1+] data to be encrypted/decrypted
- * rqst[1+].rq_iov[0+] data to be encrypted/decrypted
- */
-static struct scatterlist *
-init_sg(int num_rqst, struct smb_rqst *rqst, u8 *sign)
+static void *smb2_get_aead_req(struct crypto_aead *tfm, const struct smb_rqst *rqst,
+			       int num_rqst, const u8 *sig, u8 **iv,
+			       struct aead_request **req, struct scatterlist **sgl)
 {
-	unsigned int sg_len;
+	unsigned int off, len, skip;
 	struct scatterlist *sg;
-	unsigned int i;
-	unsigned int j;
-	unsigned int idx = 0;
-	int skip;
-
-	sg_len = 1;
-	for (i = 0; i < num_rqst; i++)
-		sg_len += rqst[i].rq_nvec + rqst[i].rq_npages;
+	unsigned int num_sgs;
+	unsigned long addr;
+	int i, j;
+	void *p;
 
-	sg = kmalloc_array(sg_len, sizeof(struct scatterlist), GFP_KERNEL);
-	if (!sg)
+	p = smb2_aead_req_alloc(tfm, rqst, num_rqst, sig, iv, req, sgl, &num_sgs);
+	if (!p)
 		return NULL;
 
-	sg_init_table(sg, sg_len);
+	sg_init_table(*sgl, num_sgs);
+	sg = *sgl;
+
+	/* Assumes the first rqst has a transform header as the first iov.
+	 * I.e.
+	 * rqst[0].rq_iov[0]  is transform header
+	 * rqst[0].rq_iov[1+] data to be encrypted/decrypted
+	 * rqst[1+].rq_iov[0+] data to be encrypted/decrypted
+	 */
 	for (i = 0; i < num_rqst; i++) {
+		/*
+		 * The first rqst has a transform header where the
+		 * first 20 bytes are not part of the encrypted blob.
+		 */
 		for (j = 0; j < rqst[i].rq_nvec; j++) {
-			/*
-			 * The first rqst has a transform header where the
-			 * first 20 bytes are not part of the encrypted blob
-			 */
-			skip = (i == 0) && (j == 0) ? 20 : 0;
-			smb2_sg_set_buf(&sg[idx++],
-					rqst[i].rq_iov[j].iov_base + skip,
-					rqst[i].rq_iov[j].iov_len - skip);
-			}
+			struct kvec *iov = &rqst[i].rq_iov[j];
 
+			skip = (i == 0) && (j == 0) ? 20 : 0;
+			addr = (unsigned long)iov->iov_base + skip;
+			len = iov->iov_len - skip;
+			sg = cifs_sg_set_buf(sg, (void *)addr, len);
+		}
 		for (j = 0; j < rqst[i].rq_npages; j++) {
-			unsigned int len, offset;
-
-			rqst_page_get_length(&rqst[i], j, &len, &offset);
-			sg_set_page(&sg[idx++], rqst[i].rq_pages[j], len, offset);
+			rqst_page_get_length(&rqst[i], j, &len, &off);
+			sg_set_page(sg++, rqst[i].rq_pages[j], len, off);
 		}
 	}
-	smb2_sg_set_buf(&sg[idx], sign, SMB2_SIGNATURE_SIZE);
-	return sg;
+	cifs_sg_set_buf(sg, sig, SMB2_SIGNATURE_SIZE);
+
+	return p;
 }
 
 static int
@@ -4490,11 +4551,11 @@
 	u8 sign[SMB2_SIGNATURE_SIZE] = {};
 	u8 key[SMB3_ENC_DEC_KEY_SIZE];
 	struct aead_request *req;
-	char *iv;
-	unsigned int iv_len;
+	u8 *iv;
 	DECLARE_CRYPTO_WAIT(wait);
 	struct crypto_aead *tfm;
 	unsigned int crypt_len = le32_to_cpu(tr_hdr->OriginalMessageSize);
+	void *creq;
 
 	rc = smb2_get_enc_key(server, tr_hdr->SessionId, enc, key);
 	if (rc) {
@@ -4529,32 +4590,15 @@
 		return rc;
 	}
 
-	req = aead_request_alloc(tfm, GFP_KERNEL);
-	if (!req) {
-		cifs_server_dbg(VFS, "%s: Failed to alloc aead request\n", __func__);
+	creq = smb2_get_aead_req(tfm, rqst, num_rqst, sign, &iv, &req, &sg);
+	if (unlikely(!creq))
 		return -ENOMEM;
-	}
 
 	if (!enc) {
 		memcpy(sign, &tr_hdr->Signature, SMB2_SIGNATURE_SIZE);
 		crypt_len += SMB2_SIGNATURE_SIZE;
 	}
 
-	sg = init_sg(num_rqst, rqst, sign);
-	if (!sg) {
-		cifs_server_dbg(VFS, "%s: Failed to init sg\n", __func__);
-		rc = -ENOMEM;
-		goto free_req;
-	}
-
-	iv_len = crypto_aead_ivsize(tfm);
-	iv = kzalloc(iv_len, GFP_KERNEL);
-	if (!iv) {
-		cifs_server_dbg(VFS, "%s: Failed to alloc iv\n", __func__);
-		rc = -ENOMEM;
-		goto free_sg;
-	}
-
 	if ((server->cipher_type == SMB2_ENCRYPTION_AES128_GCM) ||
 	    (server->cipher_type == SMB2_ENCRYPTION_AES256_GCM))
 		memcpy(iv, (char *)tr_hdr->Nonce, SMB3_AES_GCM_NONCE);
@@ -4563,6 +4607,7 @@
 		memcpy(iv + 1, (char *)tr_hdr->Nonce, SMB3_AES_CCM_NONCE);
 	}
 
+	aead_request_set_tfm(req, tfm);
 	aead_request_set_crypt(req, sg, sg, crypt_len, iv);
 	aead_request_set_ad(req, assoc_data_len);
 
@@ -4575,11 +4620,7 @@
 	if (!rc && enc)
 		memcpy(&tr_hdr->Signature, sign, SMB2_SIGNATURE_SIZE);
 
-	kfree(iv);
-free_sg:
-	kfree(sg);
-free_req:
-	kfree(req);
+	kfree_sensitive(creq);
 	return rc;
 }
 
@@ -4797,7 +4838,7 @@
 
 	if (shdr->Command != SMB2_READ) {
 		cifs_server_dbg(VFS, "only big read responses are supported\n");
-		return -ENOTSUPP;
+		return -EOPNOTSUPP;
 	}
 
 	if (server->ops->is_session_expired &&
@@ -5120,6 +5161,7 @@
 	struct smb2_sync_hdr *shdr;
 	unsigned int pdu_length = server->pdu_size;
 	unsigned int buf_size;
+	unsigned int next_cmd;
 	struct mid_q_entry *mid_entry;
 	int next_is_large;
 	char *next_buffer = NULL;
@@ -5148,14 +5190,19 @@
 	next_is_large = server->large_buf;
 one_more:
 	shdr = (struct smb2_sync_hdr *)buf;
-	if (shdr->NextCommand) {
+	next_cmd = le32_to_cpu(shdr->NextCommand);
+	if (next_cmd) {
+		if (WARN_ON_ONCE(next_cmd > pdu_length))
+			return -1;
 		if (next_is_large)
 			next_buffer = (char *)cifs_buf_get();
 		else
 			next_buffer = (char *)cifs_small_buf_get();
-		memcpy(next_buffer,
-		       buf + le32_to_cpu(shdr->NextCommand),
-		       pdu_length - le32_to_cpu(shdr->NextCommand));
+		if (!next_buffer) {
+			cifs_server_dbg(VFS, "No memory for (large) SMB response\n");
+			return -1;
+		}
+		memcpy(next_buffer, buf + next_cmd, pdu_length - next_cmd);
 	}
 
 	mid_entry = smb2_find_mid(server, buf);
@@ -5179,8 +5226,8 @@
 	else
 		ret = cifs_handle_standard(server, mid_entry);
 
-	if (ret == 0 && shdr->NextCommand) {
-		pdu_length -= le32_to_cpu(shdr->NextCommand);
+	if (ret == 0 && next_cmd) {
+		pdu_length -= next_cmd;
 		server->large_buf = next_is_large;
 		if (next_is_large)
 			server->bigbuf = buf = next_buffer;
@@ -5350,7 +5397,7 @@
 	return rc;
 }
 
-
+#ifdef CONFIG_CIFS_ALLOW_INSECURE_LEGACY
 struct smb_version_operations smb20_operations = {
 	.compare_fids = smb2_compare_fids,
 	.setup_request = smb2_setup_request,
@@ -5449,6 +5496,7 @@
 	.is_status_io_timeout = smb2_is_status_io_timeout,
 	.is_network_name_deleted = smb2_is_network_name_deleted,
 };
+#endif /* CIFS_ALLOW_INSECURE_LEGACY */
 
 struct smb_version_operations smb21_operations = {
 	.compare_fids = smb2_compare_fids,
@@ -5780,6 +5828,7 @@
 	.is_network_name_deleted = smb2_is_network_name_deleted,
 };
 
+#ifdef CONFIG_CIFS_ALLOW_INSECURE_LEGACY
 struct smb_version_values smb20_values = {
 	.version_string = SMB20_VERSION_STRING,
 	.protocol_id = SMB20_PROT_ID,
@@ -5791,7 +5840,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
@@ -5800,6 +5849,7 @@
 	.signing_required = SMB2_NEGOTIATE_SIGNING_REQUIRED,
 	.create_lease_size = sizeof(struct create_lease),
 };
+#endif /* ALLOW_INSECURE_LEGACY */
 
 struct smb_version_values smb21_values = {
 	.version_string = SMB21_VERSION_STRING,
@@ -5812,7 +5862,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
@@ -5833,7 +5883,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
@@ -5854,7 +5904,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
@@ -5875,7 +5925,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
@@ -5896,7 +5946,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
@@ -5917,7 +5967,7 @@
 	.header_size = sizeof(struct smb2_sync_hdr),
 	.header_preamble_size = 0,
 	.max_header_size = MAX_SMB2_HDR_SIZE,
-	.read_rsp_size = sizeof(struct smb2_read_rsp) - 1,
+	.read_rsp_size = sizeof(struct smb2_read_rsp),
 	.lock_cmd = SMB2_LOCK,
 	.cap_unix = 0,
 	.cap_nt_find = SMB2_NT_FIND,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2pdu.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2pdu.c
@@ -156,7 +156,11 @@
 	if (tcon == NULL)
 		return 0;
 
-	if (smb2_command == SMB2_TREE_CONNECT)
+	/*
+	 * Need to also skip SMB2_IOCTL because it is used for checking nested dfs links in
+	 * cifs_tree_connect().
+	 */
+	if (smb2_command == SMB2_TREE_CONNECT || smb2_command == SMB2_IOCTL)
 		return 0;
 
 	if (tcon->tidStatus == CifsExiting) {
@@ -268,6 +272,9 @@
 			ses->binding_chan = NULL;
 			mutex_unlock(&tcon->ses->session_mutex);
 			goto failed;
+		} else if (rc) {
+			mutex_unlock(&ses->session_mutex);
+			goto out;
 		}
 	}
 	/*
@@ -357,10 +364,15 @@
 				 void **request_buf, unsigned int *total_len)
 {
 	/* BB eventually switch this to SMB2 specific small buf size */
-	if (smb2_command == SMB2_SET_INFO)
+	switch (smb2_command) {
+	case SMB2_SET_INFO:
+	case SMB2_QUERY_INFO:
 		*request_buf = cifs_buf_get();
-	else
+		break;
+	default:
 		*request_buf = cifs_small_buf_get();
+		break;
+	}
 	if (*request_buf == NULL) {
 		/* BB should we add a retry in here if not a writepage? */
 		return -ENOMEM;
@@ -930,16 +942,17 @@
 	} else if (rc != 0)
 		goto neg_exit;
 
+	rc = -EIO;
 	if (strcmp(server->vals->version_string,
 		   SMB3ANY_VERSION_STRING) == 0) {
 		if (rsp->DialectRevision == cpu_to_le16(SMB20_PROT_ID)) {
 			cifs_server_dbg(VFS,
 				"SMB2 dialect returned but not requested\n");
-			return -EIO;
+			goto neg_exit;
 		} else if (rsp->DialectRevision == cpu_to_le16(SMB21_PROT_ID)) {
 			cifs_server_dbg(VFS,
 				"SMB2.1 dialect returned but not requested\n");
-			return -EIO;
+			goto neg_exit;
 		} else if (rsp->DialectRevision == cpu_to_le16(SMB311_PROT_ID)) {
 			/* ops set to 3.0 by default for default so update */
 			server->ops = &smb311_operations;
@@ -950,7 +963,7 @@
 		if (rsp->DialectRevision == cpu_to_le16(SMB20_PROT_ID)) {
 			cifs_server_dbg(VFS,
 				"SMB2 dialect returned but not requested\n");
-			return -EIO;
+			goto neg_exit;
 		} else if (rsp->DialectRevision == cpu_to_le16(SMB21_PROT_ID)) {
 			/* ops set to 3.0 by default for default so update */
 			server->ops = &smb21_operations;
@@ -964,7 +977,7 @@
 		/* if requested single dialect ensure returned dialect matched */
 		cifs_server_dbg(VFS, "Invalid 0x%x dialect returned: not requested\n",
 				le16_to_cpu(rsp->DialectRevision));
-		return -EIO;
+		goto neg_exit;
 	}
 
 	cifs_dbg(FYI, "mode 0x%x\n", rsp->SecurityMode);
@@ -982,9 +995,10 @@
 	else {
 		cifs_server_dbg(VFS, "Invalid dialect returned by server 0x%x\n",
 				le16_to_cpu(rsp->DialectRevision));
-		rc = -EIO;
 		goto neg_exit;
 	}
+
+	rc = 0;
 	server->dialect = le16_to_cpu(rsp->DialectRevision);
 
 	/*
@@ -1132,13 +1146,13 @@
 		pneg_inbuf->Dialects[0] =
 			cpu_to_le16(server->vals->protocol_id);
 		pneg_inbuf->DialectCount = cpu_to_le16(1);
-		/* structure is big enough for 3 dialects, sending only 1 */
+		/* structure is big enough for 4 dialects, sending only 1 */
 		inbuflen = sizeof(*pneg_inbuf) -
-				sizeof(pneg_inbuf->Dialects[0]) * 2;
+				sizeof(pneg_inbuf->Dialects[0]) * 3;
 	}
 
 	rc = SMB2_ioctl(xid, tcon, NO_FILE_ID, NO_FILE_ID,
-		FSCTL_VALIDATE_NEGOTIATE_INFO, true /* is_fsctl */,
+		FSCTL_VALIDATE_NEGOTIATE_INFO,
 		(char *)pneg_inbuf, inbuflen, CIFSMaxBufSize,
 		(char **)&pneg_rsp, &rsplen);
 	if (rc == -EOPNOTSUPP) {
@@ -1313,7 +1327,7 @@
 
 	/* Testing shows that buffer offset must be at location of Buffer[0] */
 	req->SecurityBufferOffset =
-		cpu_to_le16(sizeof(struct smb2_sess_setup_req) - 1 /* pad */);
+		cpu_to_le16(sizeof(struct smb2_sess_setup_req));
 	req->SecurityBufferLength = cpu_to_le16(sess_data->iov[1].iov_len);
 
 	memset(&rqst, 0, sizeof(struct smb_rqst));
@@ -1812,8 +1826,7 @@
 	iov[0].iov_len = total_len - 1;
 
 	/* Testing shows that buffer offset must be at location of Buffer[0] */
-	req->PathOffset = cpu_to_le16(sizeof(struct smb2_tree_connect_req)
-			- 1 /* pad */);
+	req->PathOffset = cpu_to_le16(sizeof(struct smb2_tree_connect_req));
 	req->PathLength = cpu_to_le16(unc_path_len - 2);
 	iov[1].iov_base = unc_path;
 	iov[1].iov_len = unc_path_len;
@@ -2042,17 +2055,18 @@
 		 posix->nlink, posix->mode, posix->reparse_tag);
 }
 
-void
-smb2_parse_contexts(struct TCP_Server_Info *server,
-		    struct smb2_create_rsp *rsp,
-		    unsigned int *epoch, char *lease_key, __u8 *oplock,
-		    struct smb2_file_all_info *buf,
-		    struct create_posix_rsp *posix)
+int smb2_parse_contexts(struct TCP_Server_Info *server,
+			struct kvec *rsp_iov,
+			unsigned int *epoch,
+			char *lease_key, __u8 *oplock,
+			struct smb2_file_all_info *buf,
+			struct create_posix_rsp *posix)
 {
-	char *data_offset;
+	struct smb2_create_rsp *rsp = rsp_iov->iov_base;
 	struct create_context *cc;
-	unsigned int next;
-	unsigned int remaining;
+	size_t rem, off, len;
+	size_t doff, dlen;
+	size_t noff, nlen;
 	char *name;
 	static const char smb3_create_tag_posix[] = {
 		0x93, 0xAD, 0x25, 0x50, 0x9C,
@@ -2061,45 +2075,63 @@
 	};
 
 	*oplock = 0;
-	data_offset = (char *)rsp + le32_to_cpu(rsp->CreateContextsOffset);
-	remaining = le32_to_cpu(rsp->CreateContextsLength);
-	cc = (struct create_context *)data_offset;
+
+	off = le32_to_cpu(rsp->CreateContextsOffset);
+	rem = le32_to_cpu(rsp->CreateContextsLength);
+	if (check_add_overflow(off, rem, &len) || len > rsp_iov->iov_len)
+		return -EINVAL;
+	cc = (struct create_context *)((u8 *)rsp + off);
 
 	/* Initialize inode number to 0 in case no valid data in qfid context */
 	if (buf)
 		buf->IndexNumber = 0;
 
-	while (remaining >= sizeof(struct create_context)) {
-		name = le16_to_cpu(cc->NameOffset) + (char *)cc;
-		if (le16_to_cpu(cc->NameLength) == 4 &&
-		    strncmp(name, SMB2_CREATE_REQUEST_LEASE, 4) == 0)
-			*oplock = server->ops->parse_lease_buf(cc, epoch,
-							   lease_key);
-		else if (buf && (le16_to_cpu(cc->NameLength) == 4) &&
-		    strncmp(name, SMB2_CREATE_QUERY_ON_DISK_ID, 4) == 0)
-			parse_query_id_ctxt(cc, buf);
-		else if ((le16_to_cpu(cc->NameLength) == 16)) {
-			if (posix &&
-			    memcmp(name, smb3_create_tag_posix, 16) == 0)
+	while (rem >= sizeof(*cc)) {
+		doff = le16_to_cpu(cc->DataOffset);
+		dlen = le32_to_cpu(cc->DataLength);
+		if (check_add_overflow(doff, dlen, &len) || len > rem)
+			return -EINVAL;
+
+		noff = le16_to_cpu(cc->NameOffset);
+		nlen = le16_to_cpu(cc->NameLength);
+		if (noff + nlen > doff)
+			return -EINVAL;
+
+		name = (char *)cc + noff;
+		switch (nlen) {
+		case 4:
+			if (!strncmp(name, SMB2_CREATE_REQUEST_LEASE, 4)) {
+				*oplock = server->ops->parse_lease_buf(cc, epoch,
+								       lease_key);
+			} else if (buf &&
+				   !strncmp(name, SMB2_CREATE_QUERY_ON_DISK_ID, 4)) {
+				parse_query_id_ctxt(cc, buf);
+			}
+			break;
+		case 16:
+			if (posix && !memcmp(name, smb3_create_tag_posix, 16))
 				parse_posix_ctxt(cc, buf, posix);
+			break;
+		default:
+			cifs_dbg(FYI, "%s: unhandled context (nlen=%zu dlen=%zu)\n",
+				 __func__, nlen, dlen);
+			if (IS_ENABLED(CONFIG_CIFS_DEBUG2))
+				cifs_dump_mem("context data: ", cc, dlen);
+			break;
 		}
-		/* else {
-			cifs_dbg(FYI, "Context not matched with len %d\n",
-				le16_to_cpu(cc->NameLength));
-			cifs_dump_mem("Cctxt name: ", name, 4);
-		} */
 
-		next = le32_to_cpu(cc->Next);
-		if (!next)
+		off = le32_to_cpu(cc->Next);
+		if (!off)
 			break;
-		remaining -= next;
-		cc = (struct create_context *)((char *)cc + next);
+		if (check_sub_overflow(rem, off, &rem))
+			return -EINVAL;
+		cc = (struct create_context *)((u8 *)cc + off);
 	}
 
 	if (rsp->OplockLevel != SMB2_OPLOCK_LEVEL_LEASE)
 		*oplock = rsp->OplockLevel;
 
-	return;
+	return 0;
 }
 
 static int
@@ -2349,7 +2381,7 @@
 	unsigned int acelen, acl_size, ace_count;
 	unsigned int owner_offset = 0;
 	unsigned int group_offset = 0;
-	struct smb3_acl acl;
+	struct smb3_acl acl = {};
 
 	*len = roundup(sizeof(struct crt_sd_ctxt) + (sizeof(struct cifs_ace) * 4), 8);
 
@@ -2422,6 +2454,7 @@
 	acl.AclRevision = ACL_REVISION; /* See 2.4.4.1 of MS-DTYP */
 	acl.AclSize = cpu_to_le16(acl_size);
 	acl.AceCount = cpu_to_le16(ace_count);
+	/* acl.Sbz1 and Sbz2 MBZ so are not set here, but initialized above */
 	memcpy(aclptr, &acl, sizeof(struct smb3_acl));
 
 	buf->ccontext.DataLength = cpu_to_le32(ptr - (__u8 *)&buf->sd);
@@ -2968,8 +3001,8 @@
 	}
 
 
-	smb2_parse_contexts(server, rsp, &oparms->fid->epoch,
-			    oparms->fid->lease_key, oplock, buf, posix);
+	rc = smb2_parse_contexts(server, &rsp_iov, &oparms->fid->epoch,
+				 oparms->fid->lease_key, oplock, buf, posix);
 creat_exit:
 	SMB2_open_free(&rqst);
 	free_rsp_buf(resp_buftype, rsp);
@@ -2980,7 +3013,7 @@
 SMB2_ioctl_init(struct cifs_tcon *tcon, struct TCP_Server_Info *server,
 		struct smb_rqst *rqst,
 		u64 persistent_fid, u64 volatile_fid, u32 opcode,
-		bool is_fsctl, char *in_data, u32 indatalen,
+		char *in_data, u32 indatalen,
 		__u32 max_response_size)
 {
 	struct smb2_ioctl_req *req;
@@ -2995,6 +3028,15 @@
 		return rc;
 
 	if (indatalen) {
+		unsigned int len;
+
+		if (WARN_ON_ONCE(smb3_encryption_required(tcon) &&
+				 (check_add_overflow(total_len - 1,
+						     ALIGN(indatalen, 8), &len) ||
+				  len > MAX_CIFS_SMALL_BUFFER_SIZE))) {
+			cifs_small_buf_release(req);
+			return -EIO;
+		}
 		/*
 		 * indatalen is usually small at a couple of bytes max, so
 		 * just allocate through generic pool
@@ -3055,10 +3097,8 @@
 	req->sync_hdr.CreditCharge =
 		cpu_to_le16(DIV_ROUND_UP(max(indatalen, max_response_size),
 					 SMB2_MAX_BUFFER_SIZE));
-	if (is_fsctl)
-		req->Flags = cpu_to_le32(SMB2_0_IOCTL_IS_FSCTL);
-	else
-		req->Flags = 0;
+	/* always an FSCTL (for now) */
+	req->Flags = cpu_to_le32(SMB2_0_IOCTL_IS_FSCTL);
 
 	/* validate negotiate request must be signed - see MS-SMB2 3.2.5.5 */
 	if (opcode == FSCTL_VALIDATE_NEGOTIATE_INFO)
@@ -3085,9 +3125,9 @@
  */
 int
 SMB2_ioctl(const unsigned int xid, struct cifs_tcon *tcon, u64 persistent_fid,
-	   u64 volatile_fid, u32 opcode, bool is_fsctl,
-	   char *in_data, u32 indatalen, u32 max_out_data_len,
-	   char **out_data, u32 *plen /* returned data len */)
+	   u64 volatile_fid, u32 opcode, char *in_data, u32 indatalen,
+	   u32 max_out_data_len, char **out_data,
+	   u32 *plen /* returned data len */)
 {
 	struct smb_rqst rqst;
 	struct smb2_ioctl_rsp *rsp = NULL;
@@ -3129,7 +3169,7 @@
 
 	rc = SMB2_ioctl_init(tcon, server,
 			     &rqst, persistent_fid, volatile_fid, opcode,
-			     is_fsctl, in_data, indatalen, max_out_data_len);
+			     in_data, indatalen, max_out_data_len);
 	if (rc)
 		goto ioctl_exit;
 
@@ -3211,7 +3251,7 @@
 			cpu_to_le16(COMPRESSION_FORMAT_DEFAULT);
 
 	rc = SMB2_ioctl(xid, tcon, persistent_fid, volatile_fid,
-			FSCTL_SET_COMPRESSION, true /* is_fsctl */,
+			FSCTL_SET_COMPRESSION,
 			(char *)&fsctl_input /* data input */,
 			2 /* in data len */, CIFSMaxBufSize /* max out data */,
 			&ret_data /* out data */, NULL);
@@ -3405,8 +3445,13 @@
 	struct smb2_query_info_req *req;
 	struct kvec *iov = rqst->rq_iov;
 	unsigned int total_len;
+	size_t len;
 	int rc;
 
+	if (unlikely(check_add_overflow(input_len, sizeof(*req), &len) ||
+		     len > CIFSMaxBufSize))
+		return -EINVAL;
+
 	rc = smb2_plain_req_init(SMB2_QUERY_INFO, tcon, server,
 				 (void **) &req, &total_len);
 	if (rc)
@@ -3428,7 +3473,7 @@
 
 	iov[0].iov_base = (char *)req;
 	/* 1 for Buffer */
-	iov[0].iov_len = total_len - 1 + input_len;
+	iov[0].iov_len = len;
 	return 0;
 }
 
@@ -3436,7 +3481,7 @@
 SMB2_query_info_free(struct smb_rqst *rqst)
 {
 	if (rqst && rqst->rq_iov)
-		cifs_small_buf_release(rqst->rq_iov[0].iov_base); /* request */
+		cifs_buf_release(rqst->rq_iov[0].iov_base); /* request */
 }
 
 static int
@@ -3989,12 +4034,15 @@
 				(struct smb2_sync_hdr *)rdata->iov[0].iov_base;
 	struct cifs_credits credits = { .value = 0, .instance = 0 };
 	struct smb_rqst rqst = { .rq_iov = &rdata->iov[1],
-				 .rq_nvec = 1,
-				 .rq_pages = rdata->pages,
-				 .rq_offset = rdata->page_offset,
-				 .rq_npages = rdata->nr_pages,
-				 .rq_pagesz = rdata->pagesz,
-				 .rq_tailsz = rdata->tailsz };
+				 .rq_nvec = 1, };
+
+	if (rdata->got_bytes) {
+		rqst.rq_pages = rdata->pages;
+		rqst.rq_offset = rdata->page_offset;
+		rqst.rq_npages = rdata->nr_pages;
+		rqst.rq_pagesz = rdata->pagesz;
+		rqst.rq_tailsz = rdata->tailsz;
+	}
 
 	WARN_ONCE(rdata->server != mid->server,
 		  "rdata server %p != mid server %p",
@@ -4725,7 +4773,7 @@
 	memcpy(bufptr, &asteriks, len);
 
 	req->FileNameOffset =
-		cpu_to_le16(sizeof(struct smb2_query_directory_req) - 1);
+		cpu_to_le16(sizeof(struct smb2_query_directory_req));
 	req->FileNameLength = cpu_to_le16(len);
 	/*
 	 * BB could be 30 bytes or so longer if we used SMB2 specific
@@ -4922,7 +4970,7 @@
 	req->AdditionalInformation = cpu_to_le32(additional_info);
 
 	req->BufferOffset =
-			cpu_to_le16(sizeof(struct smb2_set_info_req) - 1);
+			cpu_to_le16(sizeof(struct smb2_set_info_req));
 	req->BufferLength = cpu_to_le32(*size);
 
 	memcpy(req->Buffer, *data, *size);
@@ -5154,15 +5202,20 @@
 	req->VolatileFileId = volatile_fid;
 	/* 1 for pad */
 	req->InputBufferOffset =
-			cpu_to_le16(sizeof(struct smb2_query_info_req) - 1);
+			cpu_to_le16(sizeof(struct smb2_query_info_req));
 	req->OutputBufferLength = cpu_to_le32(
-		outbuf_len + sizeof(struct smb2_query_info_rsp) - 1);
+		outbuf_len + sizeof(struct smb2_query_info_rsp));
 
 	iov->iov_base = (char *)req;
 	iov->iov_len = total_len;
 	return 0;
 }
 
+static inline void free_qfs_info_req(struct kvec *iov)
+{
+	cifs_buf_release(iov->iov_base);
+}
+
 int
 SMB311_posix_qfs_info(const unsigned int xid, struct cifs_tcon *tcon,
 	      u64 persistent_fid, u64 volatile_fid, struct kstatfs *fsdata)
@@ -5194,7 +5247,7 @@
 
 	rc = cifs_send_recv(xid, ses, server,
 			    &rqst, &resp_buftype, flags, &rsp_iov);
-	cifs_small_buf_release(iov.iov_base);
+	free_qfs_info_req(&iov);
 	if (rc) {
 		cifs_stats_fail_inc(tcon, SMB2_QUERY_INFO_HE);
 		goto posix_qfsinf_exit;
@@ -5245,7 +5298,7 @@
 
 	rc = cifs_send_recv(xid, ses, server,
 			    &rqst, &resp_buftype, flags, &rsp_iov);
-	cifs_small_buf_release(iov.iov_base);
+	free_qfs_info_req(&iov);
 	if (rc) {
 		cifs_stats_fail_inc(tcon, SMB2_QUERY_INFO_HE);
 		goto qfsinf_exit;
@@ -5312,7 +5365,7 @@
 
 	rc = cifs_send_recv(xid, ses, server,
 			    &rqst, &resp_buftype, flags, &rsp_iov);
-	cifs_small_buf_release(iov.iov_base);
+	free_qfs_info_req(&iov);
 	if (rc) {
 		cifs_stats_fail_inc(tcon, SMB2_QUERY_INFO_HE);
 		goto qfsattr_exit;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2pdu.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2pdu.h
@@ -218,7 +218,7 @@
 	__le16 StructureSize;
 	__le16 Reserved; /* MBZ */
 	__le32 ByteCount;  /* even if zero, at least one byte follows */
-	__u8   ErrorData[1];  /* variable length */
+	__u8   ErrorData[];  /* variable length */
 } __packed;
 
 #define SYMLINK_ERROR_TAG 0x4c4d5953
@@ -487,7 +487,7 @@
 	__le16 SecurityBufferOffset;
 	__le16 SecurityBufferLength;
 	__le32 NegotiateContextOffset;	/* Pre:SMB3.1.1 was reserved/ignored */
-	__u8   Buffer[1];	/* variable length GSS security buffer */
+	__u8   Buffer[];	/* variable length GSS security buffer */
 } __packed;
 
 /* Flags */
@@ -504,7 +504,7 @@
 	__le16 SecurityBufferOffset;
 	__le16 SecurityBufferLength;
 	__u64 PreviousSessionId;
-	__u8   Buffer[1];	/* variable length GSS security buffer */
+	__u8   Buffer[];	/* variable length GSS security buffer */
 } __packed;
 
 /* Currently defined SessionFlags */
@@ -517,7 +517,7 @@
 	__le16 SessionFlags;
 	__le16 SecurityBufferOffset;
 	__le16 SecurityBufferLength;
-	__u8   Buffer[1];	/* variable length GSS security buffer */
+	__u8   Buffer[];	/* variable length GSS security buffer */
 } __packed;
 
 struct smb2_logoff_req {
@@ -543,7 +543,7 @@
 	__le16 Flags; /* Reserved MBZ for dialects prior to SMB3.1.1 */
 	__le16 PathOffset;
 	__le16 PathLength;
-	__u8   Buffer[1];	/* variable length */
+	__u8   Buffer[];	/* variable length */
 } __packed;
 
 /* See MS-SMB2 section 2.2.9.2 */
@@ -779,7 +779,7 @@
 #define SMB2_CREATE_SD_BUFFER			"SecD" /* security descriptor */
 #define SMB2_CREATE_DURABLE_HANDLE_REQUEST	"DHnQ"
 #define SMB2_CREATE_DURABLE_HANDLE_RECONNECT	"DHnC"
-#define SMB2_CREATE_ALLOCATION_SIZE		"AISi"
+#define SMB2_CREATE_ALLOCATION_SIZE		"AlSi"
 #define SMB2_CREATE_QUERY_MAXIMAL_ACCESS_REQUEST "MxAc"
 #define SMB2_CREATE_TIMEWARP_REQUEST		"TWrp"
 #define SMB2_CREATE_QUERY_ON_DISK_ID		"QFid"
@@ -852,7 +852,7 @@
 	__u64  VolatileFileId; /* opaque endianness */
 	__le32 CreateContextsOffset;
 	__le32 CreateContextsLength;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 struct create_context {
@@ -1313,7 +1313,7 @@
 	__le32 RemainingBytes;
 	__le16 ReadChannelInfoOffset;
 	__le16 ReadChannelInfoLength;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 /* Read flags */
@@ -1328,7 +1328,7 @@
 	__le32 DataLength;
 	__le32 DataRemaining;
 	__u32  Flags;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 /* For write request Flags field below the following flags are defined: */
@@ -1348,7 +1348,7 @@
 	__le16 WriteChannelInfoOffset;
 	__le16 WriteChannelInfoLength;
 	__le32 Flags;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 struct smb2_write_rsp {
@@ -1359,7 +1359,7 @@
 	__le32 DataLength;
 	__le32 DataRemaining;
 	__u32  Reserved2;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 /* notify flags */
@@ -1395,7 +1395,7 @@
 	__le16	StructureSize;  /* Must be 9 */
 	__le16	OutputBufferOffset;
 	__le32	OutputBufferLength;
-	__u8	Buffer[1]; /* array of file notify structs */
+	__u8	Buffer[]; /* array of file notify structs */
 } __packed;
 
 #define SMB2_LOCKFLAG_SHARED_LOCK	0x0001
@@ -1422,7 +1422,10 @@
 	__u64  PersistentFileId; /* opaque endianness */
 	__u64  VolatileFileId; /* opaque endianness */
 	/* Followed by at least one */
-	struct smb2_lock_element locks[1];
+	union {
+		struct smb2_lock_element lock;
+		DECLARE_FLEX_ARRAY(struct smb2_lock_element, locks);
+	};
 } __packed;
 
 struct smb2_lock_rsp {
@@ -1478,7 +1481,7 @@
 	__le16 FileNameOffset;
 	__le16 FileNameLength;
 	__le32 OutputBufferLength;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 struct smb2_query_directory_rsp {
@@ -1486,7 +1489,7 @@
 	__le16 StructureSize; /* Must be 9 */
 	__le16 OutputBufferOffset;
 	__le32 OutputBufferLength;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 /* Possible InfoType values */
@@ -1527,7 +1530,7 @@
 	__le32 Flags;
 	__u64  PersistentFileId; /* opaque endianness */
 	__u64  VolatileFileId; /* opaque endianness */
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 struct smb2_query_info_rsp {
@@ -1535,7 +1538,7 @@
 	__le16 StructureSize; /* Must be 9 */
 	__le16 OutputBufferOffset;
 	__le32 OutputBufferLength;
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 /*
@@ -1558,7 +1561,7 @@
 	__le32 AdditionalInformation;
 	__u64  PersistentFileId; /* opaque endianness */
 	__u64  VolatileFileId; /* opaque endianness */
-	__u8   Buffer[1];
+	__u8   Buffer[];
 } __packed;
 
 struct smb2_set_info_rsp {
@@ -1761,7 +1764,10 @@
 	__le32 Mode;
 	__le32 AlignmentRequirement;
 	__le32 FileNameLength;
-	char   FileName[1];
+	union {
+		char __pad;     /* Legacy structure padding */
+		DECLARE_FLEX_ARRAY(char, FileName);
+	};
 } __packed; /* level 18 Query */
 
 struct smb2_file_eof_info { /* encoding of request for level 10 */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2proto.h
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2proto.h
@@ -144,13 +144,13 @@
 extern void SMB2_open_free(struct smb_rqst *rqst);
 extern int SMB2_ioctl(const unsigned int xid, struct cifs_tcon *tcon,
 		     u64 persistent_fid, u64 volatile_fid, u32 opcode,
-		     bool is_fsctl, char *in_data, u32 indatalen, u32 maxoutlen,
+		     char *in_data, u32 indatalen, u32 maxoutlen,
 		     char **out_data, u32 *plen /* returned data len */);
 extern int SMB2_ioctl_init(struct cifs_tcon *tcon,
 			   struct TCP_Server_Info *server,
 			   struct smb_rqst *rqst,
 			   u64 persistent_fid, u64 volatile_fid, u32 opcode,
-			   bool is_fsctl, char *in_data, u32 indatalen,
+			   char *in_data, u32 indatalen,
 			   __u32 max_response_size);
 extern void SMB2_ioctl_free(struct smb_rqst *rqst);
 extern int SMB2_change_notify(const unsigned int xid, struct cifs_tcon *tcon,
@@ -259,11 +259,13 @@
 
 extern enum securityEnum smb2_select_sectype(struct TCP_Server_Info *,
 					enum securityEnum);
-extern void smb2_parse_contexts(struct TCP_Server_Info *server,
-				struct smb2_create_rsp *rsp,
-				unsigned int *epoch, char *lease_key,
-				__u8 *oplock, struct smb2_file_all_info *buf,
-				struct create_posix_rsp *posix);
+int smb2_parse_contexts(struct TCP_Server_Info *server,
+			struct kvec *rsp_iov,
+			unsigned int *epoch,
+			char *lease_key, __u8 *oplock,
+			struct smb2_file_all_info *buf,
+			struct create_posix_rsp *posix);
+
 extern int smb3_encryption_required(const struct cifs_tcon *tcon);
 extern int smb2_validate_iov(unsigned int offset, unsigned int buffer_length,
 			     struct kvec *iov, unsigned int min_buf_size);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smb2transport.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smb2transport.c
@@ -194,8 +194,8 @@
 	}
 	tcon = smb2_find_smb_sess_tcon_unlocked(ses, tid);
 	if (!tcon) {
-		cifs_put_smb_ses(ses);
 		spin_unlock(&cifs_tcp_ses_lock);
+		cifs_put_smb_ses(ses);
 		return NULL;
 	}
 	spin_unlock(&cifs_tcp_ses_lock);
@@ -221,9 +221,9 @@
 	struct smb_rqst drqst;
 
 	ses = smb2_find_smb_ses(server, shdr->SessionId);
-	if (!ses) {
+	if (unlikely(!ses)) {
 		cifs_server_dbg(VFS, "%s: Could not find session\n", __func__);
-		return 0;
+		return -ENOENT;
 	}
 
 	memset(smb2_signature, 0x0, SMB2_HMACSHA256_SIZE);
@@ -430,6 +430,8 @@
 				  ptriplet->encryption.context,
 				  ses->smb3encryptionkey,
 				  SMB3_ENC_DEC_KEY_SIZE);
+		if (rc)
+			return rc;
 		rc = generate_key(ses, ptriplet->decryption.label,
 				  ptriplet->decryption.context,
 				  ses->smb3decryptionkey,
@@ -438,9 +440,6 @@
 			return rc;
 	}
 
-	if (rc)
-		return rc;
-
 #ifdef CONFIG_CIFS_DEBUG_DUMP_KEYS
 	cifs_dbg(VFS, "%s: dumping generated AES session keys\n", __func__);
 	/*
@@ -542,8 +541,10 @@
 	u8 key[SMB3_SIGN_KEY_SIZE];
 
 	rc = smb2_get_sign_key(shdr->SessionId, server, key);
-	if (rc)
-		return 0;
+	if (unlikely(rc)) {
+		cifs_server_dbg(VFS, "%s: Could not get signing key\n", __func__);
+		return rc;
+	}
 
 	if (allocate_crypto) {
 		rc = cifs_alloc_hash("cmac(aes)", &hash, &sdesc);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/smbdirect.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/smbdirect.c
@@ -1405,6 +1405,7 @@
 	destroy_workqueue(info->workqueue);
 	log_rdma_event(INFO,  "rdma session destroyed\n");
 	kfree(info);
+	server->smbd_conn = NULL;
 }
 
 /*
@@ -1701,6 +1702,7 @@
 
 allocate_mr_failed:
 	/* At this point, need to a full transport shutdown */
+	server->smbd_conn = info;
 	smbd_destroy(server);
 	return NULL;
 
@@ -2249,6 +2251,7 @@
 	atomic_set(&info->mr_ready_count, 0);
 	atomic_set(&info->mr_used_count, 0);
 	init_waitqueue_head(&info->wait_for_mr_cleanup);
+	INIT_WORK(&info->mr_recovery_work, smbd_mr_recovery_work);
 	/* Allocate more MRs (2x) than hardware responder_resources */
 	for (i = 0; i < info->responder_resources * 2; i++) {
 		smbdirect_mr = kzalloc(sizeof(*smbdirect_mr), GFP_KERNEL);
@@ -2276,13 +2279,13 @@
 		list_add_tail(&smbdirect_mr->list, &info->mr_list);
 		atomic_inc(&info->mr_ready_count);
 	}
-	INIT_WORK(&info->mr_recovery_work, smbd_mr_recovery_work);
 	return 0;
 
 out:
 	kfree(smbdirect_mr);
 
 	list_for_each_entry_safe(smbdirect_mr, tmp, &info->mr_list, list) {
+		list_del(&smbdirect_mr->list);
 		ib_dereg_mr(smbdirect_mr->mr);
 		kfree(smbdirect_mr->sgl);
 		kfree(smbdirect_mr);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/transport.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/transport.c
@@ -196,10 +196,6 @@
 
 	*sent = 0;
 
-	smb_msg->msg_name = (struct sockaddr *) &server->dstaddr;
-	smb_msg->msg_namelen = sizeof(struct sockaddr);
-	smb_msg->msg_control = NULL;
-	smb_msg->msg_controllen = 0;
 	if (server->noblocksnd)
 		smb_msg->msg_flags = MSG_DONTWAIT + MSG_NOSIGNAL;
 	else
@@ -303,7 +299,7 @@
 __smb_send_rqst(struct TCP_Server_Info *server, int num_rqst,
 		struct smb_rqst *rqst)
 {
-	int rc = 0;
+	int rc;
 	struct kvec *iov;
 	int n_vec;
 	unsigned int send_length = 0;
@@ -311,9 +307,10 @@
 	sigset_t mask, oldmask;
 	size_t total_len = 0, sent, size;
 	struct socket *ssocket = server->ssocket;
-	struct msghdr smb_msg;
+	struct msghdr smb_msg = {};
 	__be32 rfc1002_marker;
 
+	cifs_in_send_inc(server);
 	if (cifs_rdma_enabled(server)) {
 		/* return -EAGAIN when connecting or reconnecting */
 		rc = -EAGAIN;
@@ -322,14 +319,17 @@
 		goto smbd_done;
 	}
 
+	rc = -EAGAIN;
 	if (ssocket == NULL)
-		return -EAGAIN;
+		goto out;
 
+	rc = -ERESTARTSYS;
 	if (fatal_signal_pending(current)) {
 		cifs_dbg(FYI, "signal pending before send request\n");
-		return -ERESTARTSYS;
+		goto out;
 	}
 
+	rc = 0;
 	/* cork the socket */
 	tcp_sock_set_cork(ssocket->sk, true);
 
@@ -442,7 +442,8 @@
 			 rc);
 	else if (rc > 0)
 		rc = 0;
-
+out:
+	cifs_in_send_dec(server);
 	return rc;
 }
 
@@ -859,9 +860,7 @@
 	 * I/O response may come back and free the mid entry on another thread.
 	 */
 	cifs_save_when_sent(mid);
-	cifs_in_send_inc(server);
 	rc = smb_send_rqst(server, 1, rqst, flags);
-	cifs_in_send_dec(server);
 
 	if (rc < 0) {
 		revert_current_mid(server, mid->credits);
@@ -1044,14 +1043,17 @@
 	if (!ses)
 		return NULL;
 
+	spin_lock(&ses->chan_lock);
 	if (!ses->binding) {
 		/* round robin */
 		if (ses->chan_count > 1) {
 			index = (uint)atomic_inc_return(&ses->chan_seq);
 			index %= ses->chan_count;
 		}
+		spin_unlock(&ses->chan_lock);
 		return ses->chans[index].server;
 	} else {
+		spin_unlock(&ses->chan_lock);
 		return cifs_ses_server(ses);
 	}
 }
@@ -1150,9 +1152,7 @@
 		else
 			midQ[i]->callback = cifs_compound_last_callback;
 	}
-	cifs_in_send_inc(server);
 	rc = smb_send_rqst(server, num_rqst, rqst, flags);
-	cifs_in_send_dec(server);
 
 	for (i = 0; i < num_rqst; i++)
 		cifs_save_when_sent(midQ[i]);
@@ -1389,9 +1389,7 @@
 
 	midQ->mid_state = MID_REQUEST_SUBMITTED;
 
-	cifs_in_send_inc(server);
 	rc = smb_send(server, in_buf, len);
-	cifs_in_send_dec(server);
 	cifs_save_when_sent(midQ);
 
 	if (rc < 0)
@@ -1528,9 +1526,7 @@
 	}
 
 	midQ->mid_state = MID_REQUEST_SUBMITTED;
-	cifs_in_send_inc(server);
 	rc = smb_send(server, in_buf, len);
-	cifs_in_send_dec(server);
 	cifs_save_when_sent(midQ);
 
 	if (rc < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/cifs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/cifs/xattr.c
@@ -150,10 +150,13 @@
 		if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_XATTR)
 			goto out;
 
-		if (pTcon->ses->server->ops->set_EA)
+		if (pTcon->ses->server->ops->set_EA) {
 			rc = pTcon->ses->server->ops->set_EA(xid, pTcon,
 				full_path, name, value, (__u16)size,
 				cifs_sb->local_nls, cifs_sb);
+			if (rc == 0)
+				inode_set_ctime_current(inode);
+		}
 		break;
 
 	case XATTR_CIFS_ACL:
@@ -175,11 +178,13 @@
 				switch (handler->flags) {
 				case XATTR_CIFS_NTSD_FULL:
 					aclflags = (CIFS_ACL_OWNER |
+						    CIFS_ACL_GROUP |
 						    CIFS_ACL_DACL |
 						    CIFS_ACL_SACL);
 					break;
 				case XATTR_CIFS_NTSD:
 					aclflags = (CIFS_ACL_OWNER |
+						    CIFS_ACL_GROUP |
 						    CIFS_ACL_DACL);
 					break;
 				case XATTR_CIFS_ACL:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/coda/upcall.c
+++ linux-xilinx-zynqmp-5.15.0/fs/coda/upcall.c
@@ -790,7 +790,7 @@
 	sig_req = kmalloc(sizeof(struct upc_req), GFP_KERNEL);
 	if (!sig_req) goto exit;
 
-	sig_inputArgs = kvzalloc(sizeof(struct coda_in_hdr), GFP_KERNEL);
+	sig_inputArgs = kvzalloc(sizeof(*sig_inputArgs), GFP_KERNEL);
 	if (!sig_inputArgs) {
 		kfree(sig_req);
 		goto exit;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/configfs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/configfs/dir.c
@@ -34,6 +34,14 @@
  */
 DEFINE_SPINLOCK(configfs_dirent_lock);
 
+/*
+ * All of link_obj/unlink_obj/link_group/unlink_group require that
+ * subsys->su_mutex is held.
+ * But parent configfs_subsystem is NULL when config_item is root.
+ * Use this mutex when config_item is root.
+ */
+static DEFINE_MUTEX(configfs_subsystem_mutex);
+
 static void configfs_d_iput(struct dentry * dentry,
 			    struct inode * inode)
 {
@@ -308,6 +316,7 @@
 	return 0;
 
 out_remove:
+	configfs_put(dentry->d_fsdata);
 	configfs_remove_dirent(dentry);
 	return PTR_ERR(inode);
 }
@@ -374,6 +383,7 @@
 	return 0;
 
 out_remove:
+	configfs_put(dentry->d_fsdata);
 	configfs_remove_dirent(dentry);
 	return PTR_ERR(inode);
 }
@@ -1780,8 +1790,8 @@
 	configfs_detach_group(&group->cg_item);
 	d_inode(dentry)->i_flags |= S_DEAD;
 	dont_mount(dentry);
+	d_drop(dentry);
 	fsnotify_rmdir(d_inode(parent), dentry);
-	d_delete(dentry);
 	inode_unlock(d_inode(parent));
 
 	dput(dentry);
@@ -1859,7 +1869,9 @@
 		group->cg_item.ci_name = group->cg_item.ci_namebuf;
 
 	sd = root->d_fsdata;
+	mutex_lock(&configfs_subsystem_mutex);
 	link_group(to_config_group(sd->s_element), group);
+	mutex_unlock(&configfs_subsystem_mutex);
 
 	inode_lock_nested(d_inode(root), I_MUTEX_PARENT);
 
@@ -1884,7 +1896,9 @@
 	inode_unlock(d_inode(root));
 
 	if (err) {
+		mutex_lock(&configfs_subsystem_mutex);
 		unlink_group(group);
+		mutex_unlock(&configfs_subsystem_mutex);
 		configfs_release_fs();
 	}
 	put_fragment(frag);
@@ -1922,16 +1936,18 @@
 	configfs_detach_group(&group->cg_item);
 	d_inode(dentry)->i_flags |= S_DEAD;
 	dont_mount(dentry);
-	fsnotify_rmdir(d_inode(root), dentry);
 	inode_unlock(d_inode(dentry));
 
-	d_delete(dentry);
+	d_drop(dentry);
+	fsnotify_rmdir(d_inode(root), dentry);
 
 	inode_unlock(d_inode(root));
 
 	dput(dentry);
 
+	mutex_lock(&configfs_subsystem_mutex);
 	unlink_group(group);
+	mutex_unlock(&configfs_subsystem_mutex);
 	configfs_release_fs();
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/coredump.c
+++ linux-xilinx-zynqmp-5.15.0/fs/coredump.c
@@ -41,6 +41,7 @@
 #include <linux/fs.h>
 #include <linux/path.h>
 #include <linux/timekeeping.h>
+#include <linux/elf.h>
 
 #include <linux/uaccess.h>
 #include <asm/mmu_context.h>
@@ -52,6 +53,9 @@
 
 #include <trace/events/sched.h>
 
+static bool dump_vma_snapshot(struct coredump_params *cprm);
+static void free_vma_snapshot(struct coredump_params *cprm);
+
 int core_uses_pid;
 unsigned int core_pipe_limit;
 char core_pattern[CORENAME_MAX_SIZE] = "core";
@@ -600,6 +604,7 @@
 		 * by any locks.
 		 */
 		.mm_flags = mm->flags,
+		.vma_meta = NULL,
 	};
 
 	audit_core_dumps(siginfo->si_signo);
@@ -814,6 +819,9 @@
 			pr_info("Core dump to |%s disabled\n", cn.corename);
 			goto close_fail;
 		}
+		if (!dump_vma_snapshot(&cprm))
+			goto close_fail;
+
 		file_start_write(cprm.file);
 		core_dumped = binfmt->core_dump(&cprm);
 		/*
@@ -827,6 +835,7 @@
 			dump_emit(&cprm, "", 1);
 		}
 		file_end_write(cprm.file);
+		free_vma_snapshot(&cprm);
 	}
 	if (ispipe && core_pipe_limit)
 		wait_for_dump_helpers(cprm.file);
@@ -992,6 +1001,8 @@
 	return false;
 }
 
+#define DUMP_SIZE_MAYBE_ELFHDR_PLACEHOLDER 1
+
 /*
  * Decide how much of @vma's contents should be included in a core dump.
  */
@@ -1051,9 +1062,20 @@
 	 * dump the first page to aid in determining what was mapped here.
 	 */
 	if (FILTER(ELF_HEADERS) &&
-	    vma->vm_pgoff == 0 && (vma->vm_flags & VM_READ) &&
-	    (READ_ONCE(file_inode(vma->vm_file)->i_mode) & 0111) != 0)
-		return PAGE_SIZE;
+	    vma->vm_pgoff == 0 && (vma->vm_flags & VM_READ)) {
+		if ((READ_ONCE(file_inode(vma->vm_file)->i_mode) & 0111) != 0)
+			return PAGE_SIZE;
+
+		/*
+		 * ELF libraries aren't always executable.
+		 * We'll want to check whether the mapping starts with the ELF
+		 * magic, but not now - we're holding the mmap lock,
+		 * so copy_from_user() doesn't work here.
+		 * Use a placeholder instead, and fix it up later in
+		 * dump_vma_snapshot().
+		 */
+		return DUMP_SIZE_MAYBE_ELFHDR_PLACEHOLDER;
+	}
 
 #undef	FILTER
 
@@ -1090,18 +1112,29 @@
 	return gate_vma;
 }
 
+static void free_vma_snapshot(struct coredump_params *cprm)
+{
+	if (cprm->vma_meta) {
+		int i;
+		for (i = 0; i < cprm->vma_count; i++) {
+			struct file *file = cprm->vma_meta[i].file;
+			if (file)
+				fput(file);
+		}
+		kvfree(cprm->vma_meta);
+		cprm->vma_meta = NULL;
+	}
+}
+
 /*
  * Under the mmap_lock, take a snapshot of relevant information about the task's
  * VMAs.
  */
-int dump_vma_snapshot(struct coredump_params *cprm, int *vma_count,
-		      struct core_vma_metadata **vma_meta,
-		      size_t *vma_data_size_ptr)
+static bool dump_vma_snapshot(struct coredump_params *cprm)
 {
 	struct vm_area_struct *vma, *gate_vma;
 	struct mm_struct *mm = current->mm;
 	int i;
-	size_t vma_data_size = 0;
 
 	/*
 	 * Once the stack expansion code is fixed to not change VMA bounds
@@ -1109,36 +1142,51 @@
 	 * mmap_lock in read mode.
 	 */
 	if (mmap_write_lock_killable(mm))
-		return -EINTR;
+		return false;
 
+	cprm->vma_data_size = 0;
 	gate_vma = get_gate_vma(mm);
-	*vma_count = mm->map_count + (gate_vma ? 1 : 0);
+	cprm->vma_count = mm->map_count + (gate_vma ? 1 : 0);
 
-	*vma_meta = kvmalloc_array(*vma_count, sizeof(**vma_meta), GFP_KERNEL);
-	if (!*vma_meta) {
+	cprm->vma_meta = kvmalloc_array(cprm->vma_count, sizeof(*cprm->vma_meta), GFP_KERNEL);
+	if (!cprm->vma_meta) {
 		mmap_write_unlock(mm);
-		return -ENOMEM;
+		return false;
 	}
 
 	for (i = 0, vma = first_vma(current, gate_vma); vma != NULL;
 			vma = next_vma(vma, gate_vma), i++) {
-		struct core_vma_metadata *m = (*vma_meta) + i;
+		struct core_vma_metadata *m = cprm->vma_meta + i;
 
 		m->start = vma->vm_start;
 		m->end = vma->vm_end;
 		m->flags = vma->vm_flags;
 		m->dump_size = vma_dump_size(vma, cprm->mm_flags);
+		m->pgoff = vma->vm_pgoff;
 
-		vma_data_size += m->dump_size;
+		m->file = vma->vm_file;
+		if (m->file)
+			get_file(m->file);
 	}
 
 	mmap_write_unlock(mm);
 
-	if (WARN_ON(i != *vma_count)) {
-		kvfree(*vma_meta);
-		return -EFAULT;
+	for (i = 0; i < cprm->vma_count; i++) {
+		struct core_vma_metadata *m = cprm->vma_meta + i;
+
+		if (m->dump_size == DUMP_SIZE_MAYBE_ELFHDR_PLACEHOLDER) {
+			char elfmag[SELFMAG];
+
+			if (copy_from_user(elfmag, (void __user *)m->start, SELFMAG) ||
+					memcmp(elfmag, ELFMAG, SELFMAG) != 0) {
+				m->dump_size = 0;
+			} else {
+				m->dump_size = PAGE_SIZE;
+			}
+		}
+
+		cprm->vma_data_size += m->dump_size;
 	}
 
-	*vma_data_size_ptr = vma_data_size;
-	return 0;
+	return true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/crypto/fscrypt_private.h
+++ linux-xilinx-zynqmp-5.15.0/fs/crypto/fscrypt_private.h
@@ -220,7 +220,7 @@
 	 * will be NULL if the master key was found in a process-subscribed
 	 * keyring rather than in the filesystem-level keyring.
 	 */
-	struct key *ci_master_key;
+	struct fscrypt_master_key *ci_master_key;
 
 	/*
 	 * Link in list of inodes that were unlocked with the master key.
@@ -431,6 +431,40 @@
 struct fscrypt_master_key {
 
 	/*
+	 * Back-pointer to the super_block of the filesystem to which this
+	 * master key has been added.  Only valid if ->mk_active_refs > 0.
+	 */
+	struct super_block			*mk_sb;
+
+	/*
+	 * Link in ->mk_sb->s_master_keys->key_hashtable.
+	 * Only valid if ->mk_active_refs > 0.
+	 */
+	struct hlist_node			mk_node;
+
+	/* Semaphore that protects ->mk_secret and ->mk_users */
+	struct rw_semaphore			mk_sem;
+
+	/*
+	 * Active and structural reference counts.  An active ref guarantees
+	 * that the struct continues to exist, continues to be in the keyring
+	 * ->mk_sb->s_master_keys, and that any embedded subkeys (e.g.
+	 * ->mk_direct_keys) that have been prepared continue to exist.
+	 * A structural ref only guarantees that the struct continues to exist.
+	 *
+	 * There is one active ref associated with ->mk_secret being present,
+	 * and one active ref for each inode in ->mk_decrypted_inodes.
+	 *
+	 * There is one structural ref associated with the active refcount being
+	 * nonzero.  Finding a key in the keyring also takes a structural ref,
+	 * which is then held temporarily while the key is operated on.
+	 */
+	refcount_t				mk_active_refs;
+	refcount_t				mk_struct_refs;
+
+	struct rcu_head				mk_rcu_head;
+
+	/*
 	 * The secret key material.  After FS_IOC_REMOVE_ENCRYPTION_KEY is
 	 * executed, this is wiped and no new inodes can be unlocked with this
 	 * key; however, there may still be inodes in ->mk_decrypted_inodes
@@ -438,7 +472,10 @@
 	 * FS_IOC_REMOVE_ENCRYPTION_KEY can be retried, or
 	 * FS_IOC_ADD_ENCRYPTION_KEY can add the secret again.
 	 *
-	 * Locking: protected by this master key's key->sem.
+	 * While ->mk_secret is present, one ref in ->mk_active_refs is held.
+	 *
+	 * Locking: protected by ->mk_sem.  The manipulation of ->mk_active_refs
+	 *	    associated with this field is protected by ->mk_sem as well.
 	 */
 	struct fscrypt_master_key_secret	mk_secret;
 
@@ -459,23 +496,13 @@
 	 *
 	 * This is NULL for v1 policy keys; those can only be added by root.
 	 *
-	 * Locking: in addition to this keyring's own semaphore, this is
-	 * protected by this master key's key->sem, so we can do atomic
-	 * search+insert.  It can also be searched without taking any locks, but
-	 * in that case the returned key may have already been removed.
+	 * Locking: protected by ->mk_sem.  (We don't just rely on the keyrings
+	 * subsystem semaphore ->mk_users->sem, as we need support for atomic
+	 * search+insert along with proper synchronization with ->mk_secret.)
 	 */
 	struct key		*mk_users;
 
 	/*
-	 * Length of ->mk_decrypted_inodes, plus one if mk_secret is present.
-	 * Once this goes to 0, the master key is removed from ->s_master_keys.
-	 * The 'struct fscrypt_master_key' will continue to live as long as the
-	 * 'struct key' whose payload it is, but we won't let this reference
-	 * count rise again.
-	 */
-	refcount_t		mk_refcount;
-
-	/*
 	 * List of inodes that were unlocked using this key.  This allows the
 	 * inodes to be evicted efficiently if the key is removed.
 	 */
@@ -500,10 +527,10 @@
 is_master_key_secret_present(const struct fscrypt_master_key_secret *secret)
 {
 	/*
-	 * The READ_ONCE() is only necessary for fscrypt_drop_inode() and
-	 * fscrypt_key_describe().  These run in atomic context, so they can't
-	 * take the key semaphore and thus 'secret' can change concurrently
-	 * which would be a data race.  But they only need to know whether the
+	 * The READ_ONCE() is only necessary for fscrypt_drop_inode().
+	 * fscrypt_drop_inode() runs in atomic context, so it can't take the key
+	 * semaphore and thus 'secret' can change concurrently which would be a
+	 * data race.  But fscrypt_drop_inode() only need to know whether the
 	 * secret *was* present at the time of check, so READ_ONCE() suffices.
 	 */
 	return READ_ONCE(secret->size) != 0;
@@ -532,7 +559,11 @@
 	return 0;
 }
 
-struct key *
+void fscrypt_put_master_key(struct fscrypt_master_key *mk);
+
+void fscrypt_put_master_key_activeref(struct fscrypt_master_key *mk);
+
+struct fscrypt_master_key *
 fscrypt_find_master_key(struct super_block *sb,
 			const struct fscrypt_key_specifier *mk_spec);
 
@@ -549,8 +580,9 @@
 struct fscrypt_mode {
 	const char *friendly_name;
 	const char *cipher_str;
-	int keysize;
-	int ivsize;
+	int keysize;		/* key size in bytes */
+	int security_strength;	/* security strength in bytes */
+	int ivsize;		/* IV size in bytes */
 	int logged_impl_name;
 	enum blk_crypto_mode_num blk_crypto_mode;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/crypto/hkdf.c
+++ linux-xilinx-zynqmp-5.15.0/fs/crypto/hkdf.c
@@ -16,9 +16,14 @@
 
 /*
  * HKDF supports any unkeyed cryptographic hash algorithm, but fscrypt uses
- * SHA-512 because it is reasonably secure and efficient; and since it produces
- * a 64-byte digest, deriving an AES-256-XTS key preserves all 64 bytes of
- * entropy from the master key and requires only one iteration of HKDF-Expand.
+ * SHA-512 because it is well-established, secure, and reasonably efficient.
+ *
+ * HKDF-SHA256 was also considered, as its 256-bit security strength would be
+ * sufficient here.  A 512-bit security strength is "nice to have", though.
+ * Also, on 64-bit CPUs, SHA-512 is usually just as fast as SHA-256.  In the
+ * common case of deriving an AES-256-XTS key (512 bits), that can result in
+ * HKDF-SHA512 being much faster than HKDF-SHA256, as the longer digest size of
+ * SHA-512 causes HKDF-Expand to only need to do one iteration rather than two.
  */
 #define HKDF_HMAC_ALG		"hmac(sha512)"
 #define HKDF_HASHLEN		SHA512_DIGEST_SIZE
--- linux-xilinx-zynqmp-5.15.0.orig/fs/crypto/hooks.c
+++ linux-xilinx-zynqmp-5.15.0/fs/crypto/hooks.c
@@ -5,8 +5,6 @@
  * Encryption hooks for higher-level filesystem operations.
  */
 
-#include <linux/key.h>
-
 #include "fscrypt_private.h"
 
 /**
@@ -142,7 +140,6 @@
 			     unsigned int oldflags, unsigned int flags)
 {
 	struct fscrypt_info *ci;
-	struct key *key;
 	struct fscrypt_master_key *mk;
 	int err;
 
@@ -158,14 +155,13 @@
 		ci = inode->i_crypt_info;
 		if (ci->ci_policy.version != FSCRYPT_POLICY_V2)
 			return -EINVAL;
-		key = ci->ci_master_key;
-		mk = key->payload.data[0];
-		down_read(&key->sem);
+		mk = ci->ci_master_key;
+		down_read(&mk->mk_sem);
 		if (is_master_key_secret_present(&mk->mk_secret))
 			err = fscrypt_derive_dirhash_key(ci, mk);
 		else
 			err = -ENOKEY;
-		up_read(&key->sem);
+		up_read(&mk->mk_sem);
 		return err;
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/crypto/keyring.c
+++ linux-xilinx-zynqmp-5.15.0/fs/crypto/keyring.c
@@ -18,6 +18,7 @@
  * information about these ioctls.
  */
 
+#include <asm/unaligned.h>
 #include <crypto/skcipher.h>
 #include <linux/key-type.h>
 #include <linux/random.h>
@@ -25,6 +26,18 @@
 
 #include "fscrypt_private.h"
 
+/* The master encryption keys for a filesystem (->s_master_keys) */
+struct fscrypt_keyring {
+	/*
+	 * Lock that protects ->key_hashtable.  It does *not* protect the
+	 * fscrypt_master_key structs themselves.
+	 */
+	spinlock_t lock;
+
+	/* Hash table that maps fscrypt_key_specifier to fscrypt_master_key */
+	struct hlist_head key_hashtable[128];
+};
+
 static void wipe_master_key_secret(struct fscrypt_master_key_secret *secret)
 {
 	fscrypt_destroy_hkdf(&secret->hkdf);
@@ -38,20 +51,70 @@
 	memzero_explicit(src, sizeof(*src));
 }
 
-static void free_master_key(struct fscrypt_master_key *mk)
+static void fscrypt_free_master_key(struct rcu_head *head)
+{
+	struct fscrypt_master_key *mk =
+		container_of(head, struct fscrypt_master_key, mk_rcu_head);
+	/*
+	 * The master key secret and any embedded subkeys should have already
+	 * been wiped when the last active reference to the fscrypt_master_key
+	 * struct was dropped; doing it here would be unnecessarily late.
+	 * Nevertheless, use kfree_sensitive() in case anything was missed.
+	 */
+	kfree_sensitive(mk);
+}
+
+void fscrypt_put_master_key(struct fscrypt_master_key *mk)
+{
+	if (!refcount_dec_and_test(&mk->mk_struct_refs))
+		return;
+	/*
+	 * No structural references left, so free ->mk_users, and also free the
+	 * fscrypt_master_key struct itself after an RCU grace period ensures
+	 * that concurrent keyring lookups can no longer find it.
+	 */
+	WARN_ON(refcount_read(&mk->mk_active_refs) != 0);
+	key_put(mk->mk_users);
+	mk->mk_users = NULL;
+	call_rcu(&mk->mk_rcu_head, fscrypt_free_master_key);
+}
+
+void fscrypt_put_master_key_activeref(struct fscrypt_master_key *mk)
 {
+	struct super_block *sb = mk->mk_sb;
+	struct fscrypt_keyring *keyring = sb->s_master_keys;
 	size_t i;
 
-	wipe_master_key_secret(&mk->mk_secret);
+	if (!refcount_dec_and_test(&mk->mk_active_refs))
+		return;
+	/*
+	 * No active references left, so complete the full removal of this
+	 * fscrypt_master_key struct by removing it from the keyring and
+	 * destroying any subkeys embedded in it.
+	 */
+
+	spin_lock(&keyring->lock);
+	hlist_del_rcu(&mk->mk_node);
+	spin_unlock(&keyring->lock);
+
+	/*
+	 * ->mk_active_refs == 0 implies that ->mk_secret is not present and
+	 * that ->mk_decrypted_inodes is empty.
+	 */
+	WARN_ON(is_master_key_secret_present(&mk->mk_secret));
+	WARN_ON(!list_empty(&mk->mk_decrypted_inodes));
 
 	for (i = 0; i <= FSCRYPT_MODE_MAX; i++) {
 		fscrypt_destroy_prepared_key(&mk->mk_direct_keys[i]);
 		fscrypt_destroy_prepared_key(&mk->mk_iv_ino_lblk_64_keys[i]);
 		fscrypt_destroy_prepared_key(&mk->mk_iv_ino_lblk_32_keys[i]);
 	}
+	memzero_explicit(&mk->mk_ino_hash_key,
+			 sizeof(mk->mk_ino_hash_key));
+	mk->mk_ino_hash_key_initialized = false;
 
-	key_put(mk->mk_users);
-	kfree_sensitive(mk);
+	/* Drop the structural ref associated with the active refs. */
+	fscrypt_put_master_key(mk);
 }
 
 static inline bool valid_key_spec(const struct fscrypt_key_specifier *spec)
@@ -61,44 +124,6 @@
 	return master_key_spec_len(spec) != 0;
 }
 
-static int fscrypt_key_instantiate(struct key *key,
-				   struct key_preparsed_payload *prep)
-{
-	key->payload.data[0] = (struct fscrypt_master_key *)prep->data;
-	return 0;
-}
-
-static void fscrypt_key_destroy(struct key *key)
-{
-	free_master_key(key->payload.data[0]);
-}
-
-static void fscrypt_key_describe(const struct key *key, struct seq_file *m)
-{
-	seq_puts(m, key->description);
-
-	if (key_is_positive(key)) {
-		const struct fscrypt_master_key *mk = key->payload.data[0];
-
-		if (!is_master_key_secret_present(&mk->mk_secret))
-			seq_puts(m, ": secret removed");
-	}
-}
-
-/*
- * Type of key in ->s_master_keys.  Each key of this type represents a master
- * key which has been added to the filesystem.  Its payload is a
- * 'struct fscrypt_master_key'.  The "." prefix in the key type name prevents
- * users from adding keys of this type via the keyrings syscalls rather than via
- * the intended method of FS_IOC_ADD_ENCRYPTION_KEY.
- */
-static struct key_type key_type_fscrypt = {
-	.name			= "._fscrypt",
-	.instantiate		= fscrypt_key_instantiate,
-	.destroy		= fscrypt_key_destroy,
-	.describe		= fscrypt_key_describe,
-};
-
 static int fscrypt_user_key_instantiate(struct key *key,
 					struct key_preparsed_payload *prep)
 {
@@ -131,32 +156,6 @@
 	.describe		= fscrypt_user_key_describe,
 };
 
-/* Search ->s_master_keys or ->mk_users */
-static struct key *search_fscrypt_keyring(struct key *keyring,
-					  struct key_type *type,
-					  const char *description)
-{
-	/*
-	 * We need to mark the keyring reference as "possessed" so that we
-	 * acquire permission to search it, via the KEY_POS_SEARCH permission.
-	 */
-	key_ref_t keyref = make_key_ref(keyring, true /* possessed */);
-
-	keyref = keyring_search(keyref, type, description, false);
-	if (IS_ERR(keyref)) {
-		if (PTR_ERR(keyref) == -EAGAIN || /* not found */
-		    PTR_ERR(keyref) == -EKEYREVOKED) /* recently invalidated */
-			keyref = ERR_PTR(-ENOKEY);
-		return ERR_CAST(keyref);
-	}
-	return key_ref_to_ptr(keyref);
-}
-
-#define FSCRYPT_FS_KEYRING_DESCRIPTION_SIZE	\
-	(CONST_STRLEN("fscrypt-") + sizeof_field(struct super_block, s_id))
-
-#define FSCRYPT_MK_DESCRIPTION_SIZE	(2 * FSCRYPT_KEY_IDENTIFIER_SIZE + 1)
-
 #define FSCRYPT_MK_USERS_DESCRIPTION_SIZE	\
 	(CONST_STRLEN("fscrypt-") + 2 * FSCRYPT_KEY_IDENTIFIER_SIZE + \
 	 CONST_STRLEN("-users") + 1)
@@ -164,21 +163,6 @@
 #define FSCRYPT_MK_USER_DESCRIPTION_SIZE	\
 	(2 * FSCRYPT_KEY_IDENTIFIER_SIZE + CONST_STRLEN(".uid.") + 10 + 1)
 
-static void format_fs_keyring_description(
-			char description[FSCRYPT_FS_KEYRING_DESCRIPTION_SIZE],
-			const struct super_block *sb)
-{
-	sprintf(description, "fscrypt-%s", sb->s_id);
-}
-
-static void format_mk_description(
-			char description[FSCRYPT_MK_DESCRIPTION_SIZE],
-			const struct fscrypt_key_specifier *mk_spec)
-{
-	sprintf(description, "%*phN",
-		master_key_spec_len(mk_spec), (u8 *)&mk_spec->u);
-}
-
 static void format_mk_users_keyring_description(
 			char description[FSCRYPT_MK_USERS_DESCRIPTION_SIZE],
 			const u8 mk_identifier[FSCRYPT_KEY_IDENTIFIER_SIZE])
@@ -199,20 +183,15 @@
 /* Create ->s_master_keys if needed.  Synchronized by fscrypt_add_key_mutex. */
 static int allocate_filesystem_keyring(struct super_block *sb)
 {
-	char description[FSCRYPT_FS_KEYRING_DESCRIPTION_SIZE];
-	struct key *keyring;
+	struct fscrypt_keyring *keyring;
 
 	if (sb->s_master_keys)
 		return 0;
 
-	format_fs_keyring_description(description, sb);
-	keyring = keyring_alloc(description, GLOBAL_ROOT_UID, GLOBAL_ROOT_GID,
-				current_cred(), KEY_POS_SEARCH |
-				  KEY_USR_SEARCH | KEY_USR_READ | KEY_USR_VIEW,
-				KEY_ALLOC_NOT_IN_QUOTA, NULL, NULL);
-	if (IS_ERR(keyring))
-		return PTR_ERR(keyring);
-
+	keyring = kzalloc(sizeof(*keyring), GFP_KERNEL);
+	if (!keyring)
+		return -ENOMEM;
+	spin_lock_init(&keyring->lock);
 	/*
 	 * Pairs with the smp_load_acquire() in fscrypt_find_master_key().
 	 * I.e., here we publish ->s_master_keys with a RELEASE barrier so that
@@ -222,21 +201,80 @@
 	return 0;
 }
 
-void fscrypt_sb_free(struct super_block *sb)
+/*
+ * Release all encryption keys that have been added to the filesystem, along
+ * with the keyring that contains them.
+ *
+ * This is called at unmount time.  The filesystem's underlying block device(s)
+ * are still available at this time; this is important because after user file
+ * accesses have been allowed, this function may need to evict keys from the
+ * keyslots of an inline crypto engine, which requires the block device(s).
+ *
+ * This is also called when the super_block is being freed.  This is needed to
+ * avoid a memory leak if mounting fails after the "test_dummy_encryption"
+ * option was processed, as in that case the unmount-time call isn't made.
+ */
+void fscrypt_destroy_keyring(struct super_block *sb)
 {
-	key_put(sb->s_master_keys);
+	struct fscrypt_keyring *keyring = sb->s_master_keys;
+	size_t i;
+
+	if (!keyring)
+		return;
+
+	for (i = 0; i < ARRAY_SIZE(keyring->key_hashtable); i++) {
+		struct hlist_head *bucket = &keyring->key_hashtable[i];
+		struct fscrypt_master_key *mk;
+		struct hlist_node *tmp;
+
+		hlist_for_each_entry_safe(mk, tmp, bucket, mk_node) {
+			/*
+			 * Since all inodes were already evicted, every key
+			 * remaining in the keyring should have an empty inode
+			 * list, and should only still be in the keyring due to
+			 * the single active ref associated with ->mk_secret.
+			 * There should be no structural refs beyond the one
+			 * associated with the active ref.
+			 */
+			WARN_ON(refcount_read(&mk->mk_active_refs) != 1);
+			WARN_ON(refcount_read(&mk->mk_struct_refs) != 1);
+			WARN_ON(!is_master_key_secret_present(&mk->mk_secret));
+			wipe_master_key_secret(&mk->mk_secret);
+			fscrypt_put_master_key_activeref(mk);
+		}
+	}
+	kfree_sensitive(keyring);
 	sb->s_master_keys = NULL;
 }
 
+static struct hlist_head *
+fscrypt_mk_hash_bucket(struct fscrypt_keyring *keyring,
+		       const struct fscrypt_key_specifier *mk_spec)
+{
+	/*
+	 * Since key specifiers should be "random" values, it is sufficient to
+	 * use a trivial hash function that just takes the first several bits of
+	 * the key specifier.
+	 */
+	unsigned long i = get_unaligned((unsigned long *)&mk_spec->u);
+
+	return &keyring->key_hashtable[i % ARRAY_SIZE(keyring->key_hashtable)];
+}
+
 /*
- * Find the specified master key in ->s_master_keys.
- * Returns ERR_PTR(-ENOKEY) if not found.
+ * Find the specified master key struct in ->s_master_keys and take a structural
+ * ref to it.  The structural ref guarantees that the key struct continues to
+ * exist, but it does *not* guarantee that ->s_master_keys continues to contain
+ * the key struct.  The structural ref needs to be dropped by
+ * fscrypt_put_master_key().  Returns NULL if the key struct is not found.
  */
-struct key *fscrypt_find_master_key(struct super_block *sb,
-				    const struct fscrypt_key_specifier *mk_spec)
+struct fscrypt_master_key *
+fscrypt_find_master_key(struct super_block *sb,
+			const struct fscrypt_key_specifier *mk_spec)
 {
-	struct key *keyring;
-	char description[FSCRYPT_MK_DESCRIPTION_SIZE];
+	struct fscrypt_keyring *keyring;
+	struct hlist_head *bucket;
+	struct fscrypt_master_key *mk;
 
 	/*
 	 * Pairs with the smp_store_release() in allocate_filesystem_keyring().
@@ -246,10 +284,38 @@
 	 */
 	keyring = smp_load_acquire(&sb->s_master_keys);
 	if (keyring == NULL)
-		return ERR_PTR(-ENOKEY); /* No keyring yet, so no keys yet. */
+		return NULL; /* No keyring yet, so no keys yet. */
 
-	format_mk_description(description, mk_spec);
-	return search_fscrypt_keyring(keyring, &key_type_fscrypt, description);
+	bucket = fscrypt_mk_hash_bucket(keyring, mk_spec);
+	rcu_read_lock();
+	switch (mk_spec->type) {
+	case FSCRYPT_KEY_SPEC_TYPE_DESCRIPTOR:
+		hlist_for_each_entry_rcu(mk, bucket, mk_node) {
+			if (mk->mk_spec.type ==
+				FSCRYPT_KEY_SPEC_TYPE_DESCRIPTOR &&
+			    memcmp(mk->mk_spec.u.descriptor,
+				   mk_spec->u.descriptor,
+				   FSCRYPT_KEY_DESCRIPTOR_SIZE) == 0 &&
+			    refcount_inc_not_zero(&mk->mk_struct_refs))
+				goto out;
+		}
+		break;
+	case FSCRYPT_KEY_SPEC_TYPE_IDENTIFIER:
+		hlist_for_each_entry_rcu(mk, bucket, mk_node) {
+			if (mk->mk_spec.type ==
+				FSCRYPT_KEY_SPEC_TYPE_IDENTIFIER &&
+			    memcmp(mk->mk_spec.u.identifier,
+				   mk_spec->u.identifier,
+				   FSCRYPT_KEY_IDENTIFIER_SIZE) == 0 &&
+			    refcount_inc_not_zero(&mk->mk_struct_refs))
+				goto out;
+		}
+		break;
+	}
+	mk = NULL;
+out:
+	rcu_read_unlock();
+	return mk;
 }
 
 static int allocate_master_key_users_keyring(struct fscrypt_master_key *mk)
@@ -277,17 +343,30 @@
 static struct key *find_master_key_user(struct fscrypt_master_key *mk)
 {
 	char description[FSCRYPT_MK_USER_DESCRIPTION_SIZE];
+	key_ref_t keyref;
 
 	format_mk_user_description(description, mk->mk_spec.u.identifier);
-	return search_fscrypt_keyring(mk->mk_users, &key_type_fscrypt_user,
-				      description);
+
+	/*
+	 * We need to mark the keyring reference as "possessed" so that we
+	 * acquire permission to search it, via the KEY_POS_SEARCH permission.
+	 */
+	keyref = keyring_search(make_key_ref(mk->mk_users, true /*possessed*/),
+				&key_type_fscrypt_user, description, false);
+	if (IS_ERR(keyref)) {
+		if (PTR_ERR(keyref) == -EAGAIN || /* not found */
+		    PTR_ERR(keyref) == -EKEYREVOKED) /* recently invalidated */
+			keyref = ERR_PTR(-ENOKEY);
+		return ERR_CAST(keyref);
+	}
+	return key_ref_to_ptr(keyref);
 }
 
 /*
  * Give the current user a "key" in ->mk_users.  This charges the user's quota
  * and marks the master key as added by the current user, so that it cannot be
- * removed by another user with the key.  Either the master key's key->sem must
- * be held for write, or the master key must be still undergoing initialization.
+ * removed by another user with the key.  Either ->mk_sem must be held for
+ * write, or the master key must be still undergoing initialization.
  */
 static int add_master_key_user(struct fscrypt_master_key *mk)
 {
@@ -309,7 +388,7 @@
 
 /*
  * Remove the current user's "key" from ->mk_users.
- * The master key's key->sem must be held for write.
+ * ->mk_sem must be held for write.
  *
  * Returns 0 if removed, -ENOKEY if not found, or another -errno code.
  */
@@ -327,63 +406,49 @@
 }
 
 /*
- * Allocate a new fscrypt_master_key which contains the given secret, set it as
- * the payload of a new 'struct key' of type fscrypt, and link the 'struct key'
- * into the given keyring.  Synchronized by fscrypt_add_key_mutex.
+ * Allocate a new fscrypt_master_key, transfer the given secret over to it, and
+ * insert it into sb->s_master_keys.
  */
-static int add_new_master_key(struct fscrypt_master_key_secret *secret,
-			      const struct fscrypt_key_specifier *mk_spec,
-			      struct key *keyring)
+static int add_new_master_key(struct super_block *sb,
+			      struct fscrypt_master_key_secret *secret,
+			      const struct fscrypt_key_specifier *mk_spec)
 {
+	struct fscrypt_keyring *keyring = sb->s_master_keys;
 	struct fscrypt_master_key *mk;
-	char description[FSCRYPT_MK_DESCRIPTION_SIZE];
-	struct key *key;
 	int err;
 
 	mk = kzalloc(sizeof(*mk), GFP_KERNEL);
 	if (!mk)
 		return -ENOMEM;
 
+	mk->mk_sb = sb;
+	init_rwsem(&mk->mk_sem);
+	refcount_set(&mk->mk_struct_refs, 1);
 	mk->mk_spec = *mk_spec;
 
-	move_master_key_secret(&mk->mk_secret, secret);
-
-	refcount_set(&mk->mk_refcount, 1); /* secret is present */
 	INIT_LIST_HEAD(&mk->mk_decrypted_inodes);
 	spin_lock_init(&mk->mk_decrypted_inodes_lock);
 
 	if (mk_spec->type == FSCRYPT_KEY_SPEC_TYPE_IDENTIFIER) {
 		err = allocate_master_key_users_keyring(mk);
 		if (err)
-			goto out_free_mk;
+			goto out_put;
 		err = add_master_key_user(mk);
 		if (err)
-			goto out_free_mk;
+			goto out_put;
 	}
 
-	/*
-	 * Note that we don't charge this key to anyone's quota, since when
-	 * ->mk_users is in use those keys are charged instead, and otherwise
-	 * (when ->mk_users isn't in use) only root can add these keys.
-	 */
-	format_mk_description(description, mk_spec);
-	key = key_alloc(&key_type_fscrypt, description,
-			GLOBAL_ROOT_UID, GLOBAL_ROOT_GID, current_cred(),
-			KEY_POS_SEARCH | KEY_USR_SEARCH | KEY_USR_VIEW,
-			KEY_ALLOC_NOT_IN_QUOTA, NULL);
-	if (IS_ERR(key)) {
-		err = PTR_ERR(key);
-		goto out_free_mk;
-	}
-	err = key_instantiate_and_link(key, mk, sizeof(*mk), keyring, NULL);
-	key_put(key);
-	if (err)
-		goto out_free_mk;
+	move_master_key_secret(&mk->mk_secret, secret);
+	refcount_set(&mk->mk_active_refs, 1); /* ->mk_secret is present */
 
+	spin_lock(&keyring->lock);
+	hlist_add_head_rcu(&mk->mk_node,
+			   fscrypt_mk_hash_bucket(keyring, mk_spec));
+	spin_unlock(&keyring->lock);
 	return 0;
 
-out_free_mk:
-	free_master_key(mk);
+out_put:
+	fscrypt_put_master_key(mk);
 	return err;
 }
 
@@ -392,42 +457,34 @@
 static int add_existing_master_key(struct fscrypt_master_key *mk,
 				   struct fscrypt_master_key_secret *secret)
 {
-	struct key *mk_user;
-	bool rekey;
 	int err;
 
 	/*
 	 * If the current user is already in ->mk_users, then there's nothing to
-	 * do.  (Not applicable for v1 policy keys, which have NULL ->mk_users.)
+	 * do.  Otherwise, we need to add the user to ->mk_users.  (Neither is
+	 * applicable for v1 policy keys, which have NULL ->mk_users.)
 	 */
 	if (mk->mk_users) {
-		mk_user = find_master_key_user(mk);
+		struct key *mk_user = find_master_key_user(mk);
+
 		if (mk_user != ERR_PTR(-ENOKEY)) {
 			if (IS_ERR(mk_user))
 				return PTR_ERR(mk_user);
 			key_put(mk_user);
 			return 0;
 		}
-	}
-
-	/* If we'll be re-adding ->mk_secret, try to take the reference. */
-	rekey = !is_master_key_secret_present(&mk->mk_secret);
-	if (rekey && !refcount_inc_not_zero(&mk->mk_refcount))
-		return KEY_DEAD;
-
-	/* Add the current user to ->mk_users, if applicable. */
-	if (mk->mk_users) {
 		err = add_master_key_user(mk);
-		if (err) {
-			if (rekey && refcount_dec_and_test(&mk->mk_refcount))
-				return KEY_DEAD;
+		if (err)
 			return err;
-		}
 	}
 
 	/* Re-add the secret if needed. */
-	if (rekey)
+	if (!is_master_key_secret_present(&mk->mk_secret)) {
+		if (!refcount_inc_not_zero(&mk->mk_active_refs))
+			return KEY_DEAD;
 		move_master_key_secret(&mk->mk_secret, secret);
+	}
+
 	return 0;
 }
 
@@ -436,38 +493,36 @@
 			     const struct fscrypt_key_specifier *mk_spec)
 {
 	static DEFINE_MUTEX(fscrypt_add_key_mutex);
-	struct key *key;
+	struct fscrypt_master_key *mk;
 	int err;
 
 	mutex_lock(&fscrypt_add_key_mutex); /* serialize find + link */
-retry:
-	key = fscrypt_find_master_key(sb, mk_spec);
-	if (IS_ERR(key)) {
-		err = PTR_ERR(key);
-		if (err != -ENOKEY)
-			goto out_unlock;
+
+	mk = fscrypt_find_master_key(sb, mk_spec);
+	if (!mk) {
 		/* Didn't find the key in ->s_master_keys.  Add it. */
 		err = allocate_filesystem_keyring(sb);
-		if (err)
-			goto out_unlock;
-		err = add_new_master_key(secret, mk_spec, sb->s_master_keys);
+		if (!err)
+			err = add_new_master_key(sb, secret, mk_spec);
 	} else {
 		/*
 		 * Found the key in ->s_master_keys.  Re-add the secret if
 		 * needed, and add the user to ->mk_users if needed.
 		 */
-		down_write(&key->sem);
-		err = add_existing_master_key(key->payload.data[0], secret);
-		up_write(&key->sem);
+		down_write(&mk->mk_sem);
+		err = add_existing_master_key(mk, secret);
+		up_write(&mk->mk_sem);
 		if (err == KEY_DEAD) {
-			/* Key being removed or needs to be removed */
-			key_invalidate(key);
-			key_put(key);
-			goto retry;
+			/*
+			 * We found a key struct, but it's already been fully
+			 * removed.  Ignore the old struct and add a new one.
+			 * fscrypt_add_key_mutex means we don't need to worry
+			 * about concurrent adds.
+			 */
+			err = add_new_master_key(sb, secret, mk_spec);
 		}
-		key_put(key);
+		fscrypt_put_master_key(mk);
 	}
-out_unlock:
 	mutex_unlock(&fscrypt_add_key_mutex);
 	return err;
 }
@@ -731,19 +786,19 @@
 			     const u8 identifier[FSCRYPT_KEY_IDENTIFIER_SIZE])
 {
 	struct fscrypt_key_specifier mk_spec;
-	struct key *key, *mk_user;
 	struct fscrypt_master_key *mk;
+	struct key *mk_user;
 	int err;
 
 	mk_spec.type = FSCRYPT_KEY_SPEC_TYPE_IDENTIFIER;
 	memcpy(mk_spec.u.identifier, identifier, FSCRYPT_KEY_IDENTIFIER_SIZE);
 
-	key = fscrypt_find_master_key(sb, &mk_spec);
-	if (IS_ERR(key)) {
-		err = PTR_ERR(key);
+	mk = fscrypt_find_master_key(sb, &mk_spec);
+	if (!mk) {
+		err = -ENOKEY;
 		goto out;
 	}
-	mk = key->payload.data[0];
+	down_read(&mk->mk_sem);
 	mk_user = find_master_key_user(mk);
 	if (IS_ERR(mk_user)) {
 		err = PTR_ERR(mk_user);
@@ -751,7 +806,8 @@
 		key_put(mk_user);
 		err = 0;
 	}
-	key_put(key);
+	up_read(&mk->mk_sem);
+	fscrypt_put_master_key(mk);
 out:
 	if (err == -ENOKEY && capable(CAP_FOWNER))
 		err = 0;
@@ -913,11 +969,10 @@
 	struct super_block *sb = file_inode(filp)->i_sb;
 	struct fscrypt_remove_key_arg __user *uarg = _uarg;
 	struct fscrypt_remove_key_arg arg;
-	struct key *key;
 	struct fscrypt_master_key *mk;
 	u32 status_flags = 0;
 	int err;
-	bool dead;
+	bool inodes_remain;
 
 	if (copy_from_user(&arg, uarg, sizeof(arg)))
 		return -EFAULT;
@@ -937,12 +992,10 @@
 		return -EACCES;
 
 	/* Find the key being removed. */
-	key = fscrypt_find_master_key(sb, &arg.key_spec);
-	if (IS_ERR(key))
-		return PTR_ERR(key);
-	mk = key->payload.data[0];
-
-	down_write(&key->sem);
+	mk = fscrypt_find_master_key(sb, &arg.key_spec);
+	if (!mk)
+		return -ENOKEY;
+	down_write(&mk->mk_sem);
 
 	/* If relevant, remove current user's (or all users) claim to the key */
 	if (mk->mk_users && mk->mk_users->keys.nr_leaves_on_tree != 0) {
@@ -951,7 +1004,7 @@
 		else
 			err = remove_master_key_user(mk);
 		if (err) {
-			up_write(&key->sem);
+			up_write(&mk->mk_sem);
 			goto out_put_key;
 		}
 		if (mk->mk_users->keys.nr_leaves_on_tree != 0) {
@@ -963,26 +1016,22 @@
 			status_flags |=
 				FSCRYPT_KEY_REMOVAL_STATUS_FLAG_OTHER_USERS;
 			err = 0;
-			up_write(&key->sem);
+			up_write(&mk->mk_sem);
 			goto out_put_key;
 		}
 	}
 
 	/* No user claims remaining.  Go ahead and wipe the secret. */
-	dead = false;
+	err = -ENOKEY;
 	if (is_master_key_secret_present(&mk->mk_secret)) {
 		wipe_master_key_secret(&mk->mk_secret);
-		dead = refcount_dec_and_test(&mk->mk_refcount);
-	}
-	up_write(&key->sem);
-	if (dead) {
-		/*
-		 * No inodes reference the key, and we wiped the secret, so the
-		 * key object is free to be removed from the keyring.
-		 */
-		key_invalidate(key);
+		fscrypt_put_master_key_activeref(mk);
 		err = 0;
-	} else {
+	}
+	inodes_remain = refcount_read(&mk->mk_active_refs) > 0;
+	up_write(&mk->mk_sem);
+
+	if (inodes_remain) {
 		/* Some inodes still reference this key; try to evict them. */
 		err = try_to_lock_encrypted_files(sb, mk);
 		if (err == -EBUSY) {
@@ -998,7 +1047,7 @@
 	 * has been fully removed including all files locked.
 	 */
 out_put_key:
-	key_put(key);
+	fscrypt_put_master_key(mk);
 	if (err == 0)
 		err = put_user(status_flags, &uarg->removal_status_flags);
 	return err;
@@ -1045,7 +1094,6 @@
 {
 	struct super_block *sb = file_inode(filp)->i_sb;
 	struct fscrypt_get_key_status_arg arg;
-	struct key *key;
 	struct fscrypt_master_key *mk;
 	int err;
 
@@ -1062,19 +1110,18 @@
 	arg.user_count = 0;
 	memset(arg.__out_reserved, 0, sizeof(arg.__out_reserved));
 
-	key = fscrypt_find_master_key(sb, &arg.key_spec);
-	if (IS_ERR(key)) {
-		if (key != ERR_PTR(-ENOKEY))
-			return PTR_ERR(key);
+	mk = fscrypt_find_master_key(sb, &arg.key_spec);
+	if (!mk) {
 		arg.status = FSCRYPT_KEY_STATUS_ABSENT;
 		err = 0;
 		goto out;
 	}
-	mk = key->payload.data[0];
-	down_read(&key->sem);
+	down_read(&mk->mk_sem);
 
 	if (!is_master_key_secret_present(&mk->mk_secret)) {
-		arg.status = FSCRYPT_KEY_STATUS_INCOMPLETELY_REMOVED;
+		arg.status = refcount_read(&mk->mk_active_refs) > 0 ?
+			FSCRYPT_KEY_STATUS_INCOMPLETELY_REMOVED :
+			FSCRYPT_KEY_STATUS_ABSENT /* raced with full removal */;
 		err = 0;
 		goto out_release_key;
 	}
@@ -1096,8 +1143,8 @@
 	}
 	err = 0;
 out_release_key:
-	up_read(&key->sem);
-	key_put(key);
+	up_read(&mk->mk_sem);
+	fscrypt_put_master_key(mk);
 out:
 	if (!err && copy_to_user(uarg, &arg, sizeof(arg)))
 		err = -EFAULT;
@@ -1109,13 +1156,9 @@
 {
 	int err;
 
-	err = register_key_type(&key_type_fscrypt);
-	if (err)
-		return err;
-
 	err = register_key_type(&key_type_fscrypt_user);
 	if (err)
-		goto err_unregister_fscrypt;
+		return err;
 
 	err = register_key_type(&key_type_fscrypt_provisioning);
 	if (err)
@@ -1125,7 +1168,5 @@
 
 err_unregister_fscrypt_user:
 	unregister_key_type(&key_type_fscrypt_user);
-err_unregister_fscrypt:
-	unregister_key_type(&key_type_fscrypt);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/crypto/keysetup.c
+++ linux-xilinx-zynqmp-5.15.0/fs/crypto/keysetup.c
@@ -9,7 +9,6 @@
  */
 
 #include <crypto/skcipher.h>
-#include <linux/key.h>
 #include <linux/random.h>
 
 #include "fscrypt_private.h"
@@ -19,6 +18,7 @@
 		.friendly_name = "AES-256-XTS",
 		.cipher_str = "xts(aes)",
 		.keysize = 64,
+		.security_strength = 32,
 		.ivsize = 16,
 		.blk_crypto_mode = BLK_ENCRYPTION_MODE_AES_256_XTS,
 	},
@@ -26,12 +26,14 @@
 		.friendly_name = "AES-256-CTS-CBC",
 		.cipher_str = "cts(cbc(aes))",
 		.keysize = 32,
+		.security_strength = 32,
 		.ivsize = 16,
 	},
 	[FSCRYPT_MODE_AES_128_CBC] = {
 		.friendly_name = "AES-128-CBC-ESSIV",
 		.cipher_str = "essiv(cbc(aes),sha256)",
 		.keysize = 16,
+		.security_strength = 16,
 		.ivsize = 16,
 		.blk_crypto_mode = BLK_ENCRYPTION_MODE_AES_128_CBC_ESSIV,
 	},
@@ -39,12 +41,14 @@
 		.friendly_name = "AES-128-CTS-CBC",
 		.cipher_str = "cts(cbc(aes))",
 		.keysize = 16,
+		.security_strength = 16,
 		.ivsize = 16,
 	},
 	[FSCRYPT_MODE_ADIANTUM] = {
 		.friendly_name = "Adiantum",
 		.cipher_str = "adiantum(xchacha12,aes)",
 		.keysize = 32,
+		.security_strength = 32,
 		.ivsize = 32,
 		.blk_crypto_mode = BLK_ENCRYPTION_MODE_ADIANTUM,
 	},
@@ -146,6 +150,7 @@
 {
 	crypto_free_skcipher(prep_key->tfm);
 	fscrypt_destroy_inline_crypt_key(prep_key);
+	memzero_explicit(prep_key, sizeof(*prep_key));
 }
 
 /* Given a per-file encryption key, set up the file's crypto transform object */
@@ -358,22 +363,59 @@
 }
 
 /*
+ * Check whether the size of the given master key (@mk) is appropriate for the
+ * encryption settings which a particular file will use (@ci).
+ *
+ * If the file uses a v1 encryption policy, then the master key must be at least
+ * as long as the derived key, as this is a requirement of the v1 KDF.
+ *
+ * Otherwise, the KDF can accept any size key, so we enforce a slightly looser
+ * requirement: we require that the size of the master key be at least the
+ * maximum security strength of any algorithm whose key will be derived from it
+ * (but in practice we only need to consider @ci->ci_mode, since any other
+ * possible subkeys such as DIRHASH and INODE_HASH will never increase the
+ * required key size over @ci->ci_mode).  This allows AES-256-XTS keys to be
+ * derived from a 256-bit master key, which is cryptographically sufficient,
+ * rather than requiring a 512-bit master key which is unnecessarily long.  (We
+ * still allow 512-bit master keys if the user chooses to use them, though.)
+ */
+static bool fscrypt_valid_master_key_size(const struct fscrypt_master_key *mk,
+					  const struct fscrypt_info *ci)
+{
+	unsigned int min_keysize;
+
+	if (ci->ci_policy.version == FSCRYPT_POLICY_V1)
+		min_keysize = ci->ci_mode->keysize;
+	else
+		min_keysize = ci->ci_mode->security_strength;
+
+	if (mk->mk_secret.size < min_keysize) {
+		fscrypt_warn(NULL,
+			     "key with %s %*phN is too short (got %u bytes, need %u+ bytes)",
+			     master_key_spec_type(&mk->mk_spec),
+			     master_key_spec_len(&mk->mk_spec),
+			     (u8 *)&mk->mk_spec.u,
+			     mk->mk_secret.size, min_keysize);
+		return false;
+	}
+	return true;
+}
+
+/*
  * Find the master key, then set up the inode's actual encryption key.
  *
- * If the master key is found in the filesystem-level keyring, then the
- * corresponding 'struct key' is returned in *master_key_ret with its semaphore
- * read-locked.  This is needed to ensure that only one task links the
- * fscrypt_info into ->mk_decrypted_inodes (as multiple tasks may race to create
- * an fscrypt_info for the same inode), and to synchronize the master key being
- * removed with a new inode starting to use it.
+ * If the master key is found in the filesystem-level keyring, then it is
+ * returned in *mk_ret with its semaphore read-locked.  This is needed to ensure
+ * that only one task links the fscrypt_info into ->mk_decrypted_inodes (as
+ * multiple tasks may race to create an fscrypt_info for the same inode), and to
+ * synchronize the master key being removed with a new inode starting to use it.
  */
 static int setup_file_encryption_key(struct fscrypt_info *ci,
 				     bool need_dirhash_key,
-				     struct key **master_key_ret)
+				     struct fscrypt_master_key **mk_ret)
 {
-	struct key *key;
-	struct fscrypt_master_key *mk = NULL;
 	struct fscrypt_key_specifier mk_spec;
+	struct fscrypt_master_key *mk;
 	int err;
 
 	err = fscrypt_select_encryption_impl(ci);
@@ -398,11 +440,10 @@
 		return -EINVAL;
 	}
 
-	key = fscrypt_find_master_key(ci->ci_inode->i_sb, &mk_spec);
-	if (IS_ERR(key)) {
-		if (key != ERR_PTR(-ENOKEY) ||
-		    ci->ci_policy.version != FSCRYPT_POLICY_V1)
-			return PTR_ERR(key);
+	mk = fscrypt_find_master_key(ci->ci_inode->i_sb, &mk_spec);
+	if (!mk) {
+		if (ci->ci_policy.version != FSCRYPT_POLICY_V1)
+			return -ENOKEY;
 
 		/*
 		 * As a legacy fallback for v1 policies, search for the key in
@@ -412,9 +453,7 @@
 		 */
 		return fscrypt_setup_v1_file_key_via_subscribed_keyrings(ci);
 	}
-
-	mk = key->payload.data[0];
-	down_read(&key->sem);
+	down_read(&mk->mk_sem);
 
 	/* Has the secret been removed (via FS_IOC_REMOVE_ENCRYPTION_KEY)? */
 	if (!is_master_key_secret_present(&mk->mk_secret)) {
@@ -422,18 +461,7 @@
 		goto out_release_key;
 	}
 
-	/*
-	 * Require that the master key be at least as long as the derived key.
-	 * Otherwise, the derived key cannot possibly contain as much entropy as
-	 * that required by the encryption mode it will be used for.  For v1
-	 * policies it's also required for the KDF to work at all.
-	 */
-	if (mk->mk_secret.size < ci->ci_mode->keysize) {
-		fscrypt_warn(NULL,
-			     "key with %s %*phN is too short (got %u bytes, need %u+ bytes)",
-			     master_key_spec_type(&mk_spec),
-			     master_key_spec_len(&mk_spec), (u8 *)&mk_spec.u,
-			     mk->mk_secret.size, ci->ci_mode->keysize);
+	if (!fscrypt_valid_master_key_size(mk, ci)) {
 		err = -ENOKEY;
 		goto out_release_key;
 	}
@@ -453,18 +481,18 @@
 	if (err)
 		goto out_release_key;
 
-	*master_key_ret = key;
+	*mk_ret = mk;
 	return 0;
 
 out_release_key:
-	up_read(&key->sem);
-	key_put(key);
+	up_read(&mk->mk_sem);
+	fscrypt_put_master_key(mk);
 	return err;
 }
 
 static void put_crypt_info(struct fscrypt_info *ci)
 {
-	struct key *key;
+	struct fscrypt_master_key *mk;
 
 	if (!ci)
 		return;
@@ -474,24 +502,18 @@
 	else if (ci->ci_owns_key)
 		fscrypt_destroy_prepared_key(&ci->ci_enc_key);
 
-	key = ci->ci_master_key;
-	if (key) {
-		struct fscrypt_master_key *mk = key->payload.data[0];
-
+	mk = ci->ci_master_key;
+	if (mk) {
 		/*
 		 * Remove this inode from the list of inodes that were unlocked
-		 * with the master key.
-		 *
-		 * In addition, if we're removing the last inode from a key that
-		 * already had its secret removed, invalidate the key so that it
-		 * gets removed from ->s_master_keys.
+		 * with the master key.  In addition, if we're removing the last
+		 * inode from a master key struct that already had its secret
+		 * removed, then complete the full removal of the struct.
 		 */
 		spin_lock(&mk->mk_decrypted_inodes_lock);
 		list_del(&ci->ci_master_key_link);
 		spin_unlock(&mk->mk_decrypted_inodes_lock);
-		if (refcount_dec_and_test(&mk->mk_refcount))
-			key_invalidate(key);
-		key_put(key);
+		fscrypt_put_master_key_activeref(mk);
 	}
 	memzero_explicit(ci, sizeof(*ci));
 	kmem_cache_free(fscrypt_info_cachep, ci);
@@ -505,7 +527,7 @@
 {
 	struct fscrypt_info *crypt_info;
 	struct fscrypt_mode *mode;
-	struct key *master_key = NULL;
+	struct fscrypt_master_key *mk = NULL;
 	int res;
 
 	res = fscrypt_initialize(inode->i_sb->s_cop->flags);
@@ -528,8 +550,7 @@
 	WARN_ON(mode->ivsize > FSCRYPT_MAX_IV_SIZE);
 	crypt_info->ci_mode = mode;
 
-	res = setup_file_encryption_key(crypt_info, need_dirhash_key,
-					&master_key);
+	res = setup_file_encryption_key(crypt_info, need_dirhash_key, &mk);
 	if (res)
 		goto out;
 
@@ -544,12 +565,9 @@
 		 * We won the race and set ->i_crypt_info to our crypt_info.
 		 * Now link it into the master key's inode list.
 		 */
-		if (master_key) {
-			struct fscrypt_master_key *mk =
-				master_key->payload.data[0];
-
-			refcount_inc(&mk->mk_refcount);
-			crypt_info->ci_master_key = key_get(master_key);
+		if (mk) {
+			crypt_info->ci_master_key = mk;
+			refcount_inc(&mk->mk_active_refs);
 			spin_lock(&mk->mk_decrypted_inodes_lock);
 			list_add(&crypt_info->ci_master_key_link,
 				 &mk->mk_decrypted_inodes);
@@ -559,9 +577,9 @@
 	}
 	res = 0;
 out:
-	if (master_key) {
-		up_read(&master_key->sem);
-		key_put(master_key);
+	if (mk) {
+		up_read(&mk->mk_sem);
+		fscrypt_put_master_key(mk);
 	}
 	put_crypt_info(crypt_info);
 	return res;
@@ -726,7 +744,6 @@
 int fscrypt_drop_inode(struct inode *inode)
 {
 	const struct fscrypt_info *ci = fscrypt_get_info(inode);
-	const struct fscrypt_master_key *mk;
 
 	/*
 	 * If ci is NULL, then the inode doesn't have an encryption key set up
@@ -736,7 +753,6 @@
 	 */
 	if (!ci || !ci->ci_master_key)
 		return 0;
-	mk = ci->ci_master_key->payload.data[0];
 
 	/*
 	 * With proper, non-racy use of FS_IOC_REMOVE_ENCRYPTION_KEY, all inodes
@@ -755,6 +771,6 @@
 	 * then the thread removing the key will either evict the inode itself
 	 * or will correctly detect that it wasn't evicted due to the race.
 	 */
-	return !is_master_key_secret_present(&mk->mk_secret);
+	return !is_master_key_secret_present(&ci->ci_master_key->mk_secret);
 }
 EXPORT_SYMBOL_GPL(fscrypt_drop_inode);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/crypto/policy.c
+++ linux-xilinx-zynqmp-5.15.0/fs/crypto/policy.c
@@ -692,12 +692,8 @@
 	 * delayed key setup that requires the inode number.
 	 */
 	if (ci->ci_policy.version == FSCRYPT_POLICY_V2 &&
-	    (ci->ci_policy.v2.flags & FSCRYPT_POLICY_FLAG_IV_INO_LBLK_32)) {
-		const struct fscrypt_master_key *mk =
-			ci->ci_master_key->payload.data[0];
-
-		fscrypt_hash_inode_number(ci, mk);
-	}
+	    (ci->ci_policy.v2.flags & FSCRYPT_POLICY_FLAG_IV_INO_LBLK_32))
+		fscrypt_hash_inode_number(ci, ci->ci_master_key);
 
 	return inode->i_sb->s_cop->set_context(inode, &ctx, ctxsize, fs_data);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dax.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dax.c
@@ -846,7 +846,8 @@
 			if (!pmd_dirty(*pmdp) && !pmd_write(*pmdp))
 				goto unlock_pmd;
 
-			flush_cache_page(vma, address, pfn);
+			flush_cache_range(vma, address,
+					  address + HPAGE_PMD_SIZE);
 			pmd = pmdp_invalidate(vma, address, pmdp);
 			pmd = pmd_wrprotect(pmd);
 			pmd = pmd_mkclean(pmd);
@@ -1278,6 +1279,9 @@
 	loff_t done = 0;
 	int ret;
 
+	if (!iomi.len)
+		return 0;
+
 	if (iov_iter_rw(iter) == WRITE) {
 		lockdep_assert_held_write(&iomi.inode->i_rwsem);
 		iomi.flags |= IOMAP_WRITE;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dcache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dcache.c
@@ -331,7 +331,11 @@
 	flags &= ~(DCACHE_ENTRY_TYPE | DCACHE_FALLTHRU);
 	WRITE_ONCE(dentry->d_flags, flags);
 	dentry->d_inode = NULL;
-	if (dentry->d_flags & DCACHE_LRU_LIST)
+	/*
+	 * The negative counter only tracks dentries on the LRU. Don't inc if
+	 * d_lru is on another list.
+	 */
+	if ((flags & (DCACHE_LRU_LIST|DCACHE_SHRINK_LIST)) == DCACHE_LRU_LIST)
 		this_cpu_inc(nr_dentry_negative);
 }
 
@@ -762,12 +766,12 @@
 	 */
 	if (unlikely(ret < 0)) {
 		spin_lock(&dentry->d_lock);
-		if (dentry->d_lockref.count > 1) {
-			dentry->d_lockref.count--;
+		if (WARN_ON_ONCE(dentry->d_lockref.count <= 0)) {
 			spin_unlock(&dentry->d_lock);
 			return true;
 		}
-		return false;
+		dentry->d_lockref.count--;
+		goto locked;
 	}
 
 	/*
@@ -825,6 +829,7 @@
 	 * else could have killed it and marked it dead. Either way, we
 	 * don't need to do anything else.
 	 */
+locked:
 	if (dentry->d_lockref.count) {
 		spin_unlock(&dentry->d_lock);
 		return true;
@@ -1320,7 +1325,7 @@
  *
  * The @enter() callbacks are called with d_lock held.
  */
-static void d_walk(struct dentry *parent, void *data,
+void d_walk(struct dentry *parent, void *data,
 		   enum d_walk_ret (*enter)(void *, struct dentry *))
 {
 	struct dentry *this_parent;
@@ -1425,6 +1430,7 @@
 	seq = 1;
 	goto again;
 }
+EXPORT_SYMBOL_GPL(d_walk);
 
 struct check_mount {
 	struct vfsmount *mnt;
@@ -1974,9 +1980,11 @@
 
 	spin_lock(&dentry->d_lock);
 	/*
-	 * Decrement negative dentry count if it was in the LRU list.
+	 * The negative counter only tracks dentries on the LRU. Don't dec if
+	 * d_lru is on another list.
 	 */
-	if (dentry->d_flags & DCACHE_LRU_LIST)
+	if ((dentry->d_flags &
+	     (DCACHE_LRU_LIST|DCACHE_SHRINK_LIST)) == DCACHE_LRU_LIST)
 		this_cpu_dec(nr_dentry_negative);
 	hlist_add_head(&dentry->d_u.d_alias, &inode->i_dentry);
 	raw_write_seqcount_begin(&dentry->d_seq);
@@ -2970,6 +2978,7 @@
 
 	write_sequnlock(&rename_lock);
 }
+EXPORT_SYMBOL_GPL(d_exchange);
 
 /**
  * d_ancestor - search for an ancestor
@@ -3120,28 +3129,25 @@
   
 bool is_subdir(struct dentry *new_dentry, struct dentry *old_dentry)
 {
-	bool result;
+	bool subdir;
 	unsigned seq;
 
 	if (new_dentry == old_dentry)
 		return true;
 
-	do {
-		/* for restarting inner loop in case of seq retry */
-		seq = read_seqbegin(&rename_lock);
-		/*
-		 * Need rcu_readlock to protect against the d_parent trashing
-		 * due to d_move
-		 */
-		rcu_read_lock();
-		if (d_ancestor(old_dentry, new_dentry))
-			result = true;
-		else
-			result = false;
-		rcu_read_unlock();
-	} while (read_seqretry(&rename_lock, seq));
-
-	return result;
+	/* Access d_parent under rcu as d_move() may change it. */
+	rcu_read_lock();
+	seq = read_seqbegin(&rename_lock);
+	subdir = d_ancestor(old_dentry, new_dentry);
+	 /* Try lockless once... */
+	if (read_seqretry(&rename_lock, seq)) {
+		/* ...else acquire lock for progress even on deep chains. */
+		read_seqlock_excl(&rename_lock);
+		subdir = d_ancestor(old_dentry, new_dentry);
+		read_sequnlock_excl(&rename_lock);
+	}
+	rcu_read_unlock();
+	return subdir;
 }
 EXPORT_SYMBOL(is_subdir);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/debugfs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/debugfs/file.c
@@ -84,6 +84,14 @@
 	struct debugfs_fsdata *fsd;
 	void *d_fsd;
 
+	/*
+	 * This could only happen if some debugfs user erroneously calls
+	 * debugfs_file_get() on a dentry that isn't even a file, let
+	 * them know about it.
+	 */
+	if (WARN_ON(!d_is_reg(dentry)))
+		return -EINVAL;
+
 	d_fsd = READ_ONCE(dentry->d_fsdata);
 	if (!((unsigned long)d_fsd & DEBUGFS_FSDATA_IS_REAL_FOPS_BIT)) {
 		fsd = d_fsd;
@@ -147,7 +155,7 @@
 			       struct file *filp,
 			       const struct file_operations *real_fops)
 {
-	if ((inode->i_mode & 07777) == 0444 &&
+	if ((inode->i_mode & 07777 & ~0444) == 0 &&
 	    !(filp->f_mode & FMODE_WRITE) &&
 	    !real_fops->unlocked_ioctl &&
 	    !real_fops->compat_ioctl &&
@@ -378,8 +386,8 @@
 }
 EXPORT_SYMBOL_GPL(debugfs_attr_read);
 
-ssize_t debugfs_attr_write(struct file *file, const char __user *buf,
-			 size_t len, loff_t *ppos)
+static ssize_t debugfs_attr_write_xsigned(struct file *file, const char __user *buf,
+			 size_t len, loff_t *ppos, bool is_signed)
 {
 	struct dentry *dentry = F_DENTRY(file);
 	ssize_t ret;
@@ -387,12 +395,28 @@
 	ret = debugfs_file_get(dentry);
 	if (unlikely(ret))
 		return ret;
-	ret = simple_attr_write(file, buf, len, ppos);
+	if (is_signed)
+		ret = simple_attr_write_signed(file, buf, len, ppos);
+	else
+		ret = simple_attr_write(file, buf, len, ppos);
 	debugfs_file_put(dentry);
 	return ret;
 }
+
+ssize_t debugfs_attr_write(struct file *file, const char __user *buf,
+			 size_t len, loff_t *ppos)
+{
+	return debugfs_attr_write_xsigned(file, buf, len, ppos, false);
+}
 EXPORT_SYMBOL_GPL(debugfs_attr_write);
 
+ssize_t debugfs_attr_write_signed(struct file *file, const char __user *buf,
+			 size_t len, loff_t *ppos)
+{
+	return debugfs_attr_write_xsigned(file, buf, len, ppos, true);
+}
+EXPORT_SYMBOL_GPL(debugfs_attr_write_signed);
+
 static struct dentry *debugfs_create_mode_unsafe(const char *name, umode_t mode,
 					struct dentry *parent, void *value,
 					const struct file_operations *fops,
@@ -738,11 +762,11 @@
 	*val = atomic_read((atomic_t *)data);
 	return 0;
 }
-DEFINE_DEBUGFS_ATTRIBUTE(fops_atomic_t, debugfs_atomic_t_get,
+DEFINE_DEBUGFS_ATTRIBUTE_SIGNED(fops_atomic_t, debugfs_atomic_t_get,
 			debugfs_atomic_t_set, "%lld\n");
-DEFINE_DEBUGFS_ATTRIBUTE(fops_atomic_t_ro, debugfs_atomic_t_get, NULL,
+DEFINE_DEBUGFS_ATTRIBUTE_SIGNED(fops_atomic_t_ro, debugfs_atomic_t_get, NULL,
 			"%lld\n");
-DEFINE_DEBUGFS_ATTRIBUTE(fops_atomic_t_wo, NULL, debugfs_atomic_t_set,
+DEFINE_DEBUGFS_ATTRIBUTE_SIGNED(fops_atomic_t_wo, NULL, debugfs_atomic_t_set,
 			"%lld\n");
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/fs/debugfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/debugfs/inode.c
@@ -214,17 +214,19 @@
 
 static void debugfs_release_dentry(struct dentry *dentry)
 {
-	void *fsd = dentry->d_fsdata;
+	struct debugfs_fsdata *fsd = dentry->d_fsdata;
 
-	if (!((unsigned long)fsd & DEBUGFS_FSDATA_IS_REAL_FOPS_BIT))
-		kfree(dentry->d_fsdata);
+	if ((unsigned long)fsd & DEBUGFS_FSDATA_IS_REAL_FOPS_BIT)
+		return;
+
+	kfree(fsd);
 }
 
 static struct vfsmount *debugfs_automount(struct path *path)
 {
-	debugfs_automount_t f;
-	f = (debugfs_automount_t)path->dentry->d_fsdata;
-	return f(path->dentry, d_inode(path->dentry)->i_private);
+	struct debugfs_fsdata *fsd = path->dentry->d_fsdata;
+
+	return fsd->automount(path->dentry, d_inode(path->dentry)->i_private);
 }
 
 static const struct dentry_operations debugfs_dops = {
@@ -602,13 +604,23 @@
 					void *data)
 {
 	struct dentry *dentry = start_creating(name, parent);
+	struct debugfs_fsdata *fsd;
 	struct inode *inode;
 
 	if (IS_ERR(dentry))
 		return dentry;
 
+	fsd = kzalloc(sizeof(*fsd), GFP_KERNEL);
+	if (!fsd) {
+		failed_creating(dentry);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	fsd->automount = f;
+
 	if (!(debugfs_allow & DEBUGFS_ALLOW_API)) {
 		failed_creating(dentry);
+		kfree(fsd);
 		return ERR_PTR(-EPERM);
 	}
 
@@ -616,13 +628,14 @@
 	if (unlikely(!inode)) {
 		pr_err("out of free dentries, can not create automount '%s'\n",
 		       name);
+		kfree(fsd);
 		return failed_creating(dentry);
 	}
 
 	make_empty_dir_inode(inode);
 	inode->i_flags |= S_AUTOMOUNT;
 	inode->i_private = data;
-	dentry->d_fsdata = (void *)f;
+	dentry->d_fsdata = fsd;
 	/* directory inodes start off with i_nlink == 2 (for "." entry) */
 	inc_nlink(inode);
 	d_instantiate(dentry, inode);
@@ -735,6 +748,28 @@
 EXPORT_SYMBOL_GPL(debugfs_remove);
 
 /**
+ * debugfs_lookup_and_remove - lookup a directory or file and recursively remove it
+ * @name: a pointer to a string containing the name of the item to look up.
+ * @parent: a pointer to the parent dentry of the item.
+ *
+ * This is the equlivant of doing something like
+ * debugfs_remove(debugfs_lookup(..)) but with the proper reference counting
+ * handled for the directory being looked up.
+ */
+void debugfs_lookup_and_remove(const char *name, struct dentry *parent)
+{
+	struct dentry *dentry;
+
+	dentry = debugfs_lookup(name, parent);
+	if (!dentry)
+		return;
+
+	debugfs_remove(dentry);
+	dput(dentry);
+}
+EXPORT_SYMBOL_GPL(debugfs_lookup_and_remove);
+
+/**
  * debugfs_rename - rename a file/directory in the debugfs filesystem
  * @old_dir: a pointer to the parent dentry for the renamed object. This
  *          should be a directory dentry.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/debugfs/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/debugfs/internal.h
@@ -17,8 +17,14 @@
 
 struct debugfs_fsdata {
 	const struct file_operations *real_fops;
-	refcount_t active_users;
-	struct completion active_users_drained;
+	union {
+		/* automount_fn is used when real_fops is NULL */
+		debugfs_automount_t automount;
+		struct {
+			refcount_t active_users;
+			struct completion active_users_drained;
+		};
+	};
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/devpts/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/devpts/inode.c
@@ -621,8 +621,8 @@
 
 	dentry->d_fsdata = NULL;
 	drop_nlink(dentry->d_inode);
-	fsnotify_unlink(d_inode(dentry->d_parent), dentry);
 	d_drop(dentry);
+	fsnotify_unlink(d_inode(dentry->d_parent), dentry);
 	dput(dentry);	/* d_alloc_name() in devpts_pty_new() */
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/ast.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/ast.c
@@ -198,13 +198,13 @@
 	if (!prev_seq) {
 		kref_get(&lkb->lkb_ref);
 
+		mutex_lock(&ls->ls_cb_mutex);
 		if (test_bit(LSFL_CB_DELAY, &ls->ls_flags)) {
-			mutex_lock(&ls->ls_cb_mutex);
 			list_add(&lkb->lkb_cb_list, &ls->ls_cb_delay);
-			mutex_unlock(&ls->ls_cb_mutex);
 		} else {
 			queue_work(ls->ls_callback_wq, &lkb->lkb_cb_work);
 		}
+		mutex_unlock(&ls->ls_cb_mutex);
 	}
  out:
 	mutex_unlock(&lkb->lkb_cb_mutex);
@@ -284,7 +284,9 @@
 
 void dlm_callback_suspend(struct dlm_ls *ls)
 {
+	mutex_lock(&ls->ls_cb_mutex);
 	set_bit(LSFL_CB_DELAY, &ls->ls_flags);
+	mutex_unlock(&ls->ls_cb_mutex);
 
 	if (ls->ls_callback_wq)
 		flush_workqueue(ls->ls_callback_wq);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/lock.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/lock.c
@@ -1551,6 +1551,7 @@
 		lkb->lkb_wait_type = 0;
 		lkb->lkb_flags &= ~DLM_IFL_OVERLAP_CANCEL;
 		lkb->lkb_wait_count--;
+		unhold_lkb(lkb);
 		goto out_del;
 	}
 
@@ -1577,6 +1578,7 @@
 		log_error(ls, "remwait error %x reply %d wait_type %d overlap",
 			  lkb->lkb_id, mstype, lkb->lkb_wait_type);
 		lkb->lkb_wait_count--;
+		unhold_lkb(lkb);
 		lkb->lkb_wait_type = 0;
 	}
 
@@ -1854,7 +1856,7 @@
 void dlm_scan_timeout(struct dlm_ls *ls)
 {
 	struct dlm_rsb *r;
-	struct dlm_lkb *lkb;
+	struct dlm_lkb *lkb = NULL, *iter;
 	int do_cancel, do_warn;
 	s64 wait_us;
 
@@ -1865,27 +1867,28 @@
 		do_cancel = 0;
 		do_warn = 0;
 		mutex_lock(&ls->ls_timeout_mutex);
-		list_for_each_entry(lkb, &ls->ls_timeout, lkb_time_list) {
+		list_for_each_entry(iter, &ls->ls_timeout, lkb_time_list) {
 
 			wait_us = ktime_to_us(ktime_sub(ktime_get(),
-					      		lkb->lkb_timestamp));
+							iter->lkb_timestamp));
 
-			if ((lkb->lkb_exflags & DLM_LKF_TIMEOUT) &&
-			    wait_us >= (lkb->lkb_timeout_cs * 10000))
+			if ((iter->lkb_exflags & DLM_LKF_TIMEOUT) &&
+			    wait_us >= (iter->lkb_timeout_cs * 10000))
 				do_cancel = 1;
 
-			if ((lkb->lkb_flags & DLM_IFL_WATCH_TIMEWARN) &&
+			if ((iter->lkb_flags & DLM_IFL_WATCH_TIMEWARN) &&
 			    wait_us >= dlm_config.ci_timewarn_cs * 10000)
 				do_warn = 1;
 
 			if (!do_cancel && !do_warn)
 				continue;
-			hold_lkb(lkb);
+			hold_lkb(iter);
+			lkb = iter;
 			break;
 		}
 		mutex_unlock(&ls->ls_timeout_mutex);
 
-		if (!do_cancel && !do_warn)
+		if (!lkb)
 			break;
 
 		r = lkb->lkb_resource;
@@ -2886,24 +2889,24 @@
 static int validate_lock_args(struct dlm_ls *ls, struct dlm_lkb *lkb,
 			      struct dlm_args *args)
 {
-	int rv = -EINVAL;
+	int rv = -EBUSY;
 
 	if (args->flags & DLM_LKF_CONVERT) {
-		if (lkb->lkb_flags & DLM_IFL_MSTCPY)
+		if (lkb->lkb_status != DLM_LKSTS_GRANTED)
 			goto out;
 
-		if (args->flags & DLM_LKF_QUECVT &&
-		    !__quecvt_compat_matrix[lkb->lkb_grmode+1][args->mode+1])
+		if (lkb->lkb_wait_type)
 			goto out;
 
-		rv = -EBUSY;
-		if (lkb->lkb_status != DLM_LKSTS_GRANTED)
+		if (is_overlap(lkb))
 			goto out;
 
-		if (lkb->lkb_wait_type)
+		rv = -EINVAL;
+		if (lkb->lkb_flags & DLM_IFL_MSTCPY)
 			goto out;
 
-		if (is_overlap(lkb))
+		if (args->flags & DLM_LKF_QUECVT &&
+		    !__quecvt_compat_matrix[lkb->lkb_grmode+1][args->mode+1])
 			goto out;
 	}
 
@@ -3630,7 +3633,7 @@
 	case DLM_MSG_REQUEST_REPLY:
 	case DLM_MSG_CONVERT_REPLY:
 	case DLM_MSG_GRANT:
-		if (!lkb->lkb_lvbptr)
+		if (!lkb->lkb_lvbptr || !(lkb->lkb_exflags & DLM_LKF_VALBLK))
 			break;
 		memcpy(ms->m_extra, lkb->lkb_lvbptr, r->res_ls->ls_lvblen);
 		break;
@@ -3973,6 +3976,14 @@
 	int from = ms->m_header.h_nodeid;
 	int error = 0;
 
+	/* currently mixing of user/kernel locks are not supported */
+	if (ms->m_flags & DLM_IFL_USER && ~lkb->lkb_flags & DLM_IFL_USER) {
+		log_error(lkb->lkb_resource->res_ls,
+			  "got user dlm message for a kernel lock");
+		error = -EINVAL;
+		goto out;
+	}
+
 	switch (ms->m_type) {
 	case DLM_MSG_CONVERT:
 	case DLM_MSG_UNLOCK:
@@ -4001,6 +4012,7 @@
 		error = -EINVAL;
 	}
 
+out:
 	if (error)
 		log_error(lkb->lkb_resource->res_ls,
 			  "ignore invalid message %d from %d %x %x %x %d",
@@ -4054,13 +4066,14 @@
 	rv = _create_message(ls, sizeof(struct dlm_message) + len,
 			     dir_nodeid, DLM_MSG_REMOVE, &ms, &mh);
 	if (rv)
-		return;
+		goto out;
 
 	memcpy(ms->m_extra, name, len);
 	ms->m_hash = hash;
 
 	send_message(mh, ms);
 
+out:
 	spin_lock(&ls->ls_remove_spin);
 	ls->ls_remove_len = 0;
 	memset(ls->ls_remove_name, 0, DLM_RESNAME_MAXLEN);
@@ -5227,21 +5240,18 @@
 
 static struct dlm_lkb *find_resend_waiter(struct dlm_ls *ls)
 {
-	struct dlm_lkb *lkb;
-	int found = 0;
+	struct dlm_lkb *lkb = NULL, *iter;
 
 	mutex_lock(&ls->ls_waiters_mutex);
-	list_for_each_entry(lkb, &ls->ls_waiters, lkb_wait_reply) {
-		if (lkb->lkb_flags & DLM_IFL_RESEND) {
-			hold_lkb(lkb);
-			found = 1;
+	list_for_each_entry(iter, &ls->ls_waiters, lkb_wait_reply) {
+		if (iter->lkb_flags & DLM_IFL_RESEND) {
+			hold_lkb(iter);
+			lkb = iter;
 			break;
 		}
 	}
 	mutex_unlock(&ls->ls_waiters_mutex);
 
-	if (!found)
-		lkb = NULL;
 	return lkb;
 }
 
@@ -5301,11 +5311,16 @@
 		lkb->lkb_flags &= ~DLM_IFL_OVERLAP_UNLOCK;
 		lkb->lkb_flags &= ~DLM_IFL_OVERLAP_CANCEL;
 		lkb->lkb_wait_type = 0;
-		lkb->lkb_wait_count = 0;
+		/* drop all wait_count references we still
+		 * hold a reference for this iteration.
+		 */
+		while (lkb->lkb_wait_count) {
+			lkb->lkb_wait_count--;
+			unhold_lkb(lkb);
+		}
 		mutex_lock(&ls->ls_waiters_mutex);
 		list_del_init(&lkb->lkb_wait_reply);
 		mutex_unlock(&ls->ls_waiters_mutex);
-		unhold_lkb(lkb); /* for waiters list */
 
 		if (oc || ou) {
 			/* do an unlock or cancel instead of resending */
@@ -5895,37 +5910,36 @@
 		     int mode, uint32_t flags, void *name, unsigned int namelen,
 		     unsigned long timeout_cs, uint32_t *lkid)
 {
-	struct dlm_lkb *lkb;
+	struct dlm_lkb *lkb = NULL, *iter;
 	struct dlm_user_args *ua;
 	int found_other_mode = 0;
-	int found = 0;
 	int rv = 0;
 
 	mutex_lock(&ls->ls_orphans_mutex);
-	list_for_each_entry(lkb, &ls->ls_orphans, lkb_ownqueue) {
-		if (lkb->lkb_resource->res_length != namelen)
+	list_for_each_entry(iter, &ls->ls_orphans, lkb_ownqueue) {
+		if (iter->lkb_resource->res_length != namelen)
 			continue;
-		if (memcmp(lkb->lkb_resource->res_name, name, namelen))
+		if (memcmp(iter->lkb_resource->res_name, name, namelen))
 			continue;
-		if (lkb->lkb_grmode != mode) {
+		if (iter->lkb_grmode != mode) {
 			found_other_mode = 1;
 			continue;
 		}
 
-		found = 1;
-		list_del_init(&lkb->lkb_ownqueue);
-		lkb->lkb_flags &= ~DLM_IFL_ORPHAN;
-		*lkid = lkb->lkb_id;
+		lkb = iter;
+		list_del_init(&iter->lkb_ownqueue);
+		iter->lkb_flags &= ~DLM_IFL_ORPHAN;
+		*lkid = iter->lkb_id;
 		break;
 	}
 	mutex_unlock(&ls->ls_orphans_mutex);
 
-	if (!found && found_other_mode) {
+	if (!lkb && found_other_mode) {
 		rv = -EAGAIN;
 		goto out;
 	}
 
-	if (!found) {
+	if (!lkb) {
 		rv = -ENOENT;
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/lockspace.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/lockspace.c
@@ -17,7 +17,6 @@
 #include "recoverd.h"
 #include "dir.h"
 #include "midcomms.h"
-#include "lowcomms.h"
 #include "config.h"
 #include "memory.h"
 #include "lock.h"
@@ -384,23 +383,23 @@
 {
 	int error;
 
-	error = dlm_scand_start();
+	/* Thread for sending/receiving messages for all lockspace's */
+	error = dlm_midcomms_start();
 	if (error) {
-		log_print("cannot start dlm_scand thread %d", error);
+		log_print("cannot start dlm midcomms %d", error);
 		goto fail;
 	}
 
-	/* Thread for sending/receiving messages for all lockspace's */
-	error = dlm_midcomms_start();
+	error = dlm_scand_start();
 	if (error) {
-		log_print("cannot start dlm lowcomms %d", error);
-		goto scand_fail;
+		log_print("cannot start dlm_scand thread %d", error);
+		goto midcomms_fail;
 	}
 
 	return 0;
 
- scand_fail:
-	dlm_scand_stop();
+ midcomms_fail:
+	dlm_midcomms_stop();
  fail:
 	return error;
 }
@@ -705,7 +704,7 @@
 	if (!ls_count) {
 		dlm_scand_stop();
 		dlm_midcomms_shutdown();
-		dlm_lowcomms_stop();
+		dlm_midcomms_stop();
 	}
  out:
 	mutex_unlock(&ls_lock);
@@ -889,7 +888,7 @@
 	if (!error)
 		ls_count--;
 	if (!ls_count)
-		dlm_lowcomms_stop();
+		dlm_midcomms_stop();
 	mutex_unlock(&ls_lock);
 
 	return error;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/lowcomms.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/lowcomms.c
@@ -592,8 +592,8 @@
 static void lowcomms_error_report(struct sock *sk)
 {
 	struct connection *con;
-	struct sockaddr_storage saddr;
 	void (*orig_report)(struct sock *) = NULL;
+	struct inet_sock *inet;
 
 	read_lock_bh(&sk->sk_callback_lock);
 	con = sock2con(sk);
@@ -601,33 +601,33 @@
 		goto out;
 
 	orig_report = listen_sock.sk_error_report;
-	if (kernel_getpeername(sk->sk_socket, (struct sockaddr *)&saddr) < 0) {
-		printk_ratelimited(KERN_ERR "dlm: node %d: socket error "
-				   "sending to node %d, port %d, "
-				   "sk_err=%d/%d\n", dlm_our_nodeid(),
-				   con->nodeid, dlm_config.ci_tcp_port,
-				   sk->sk_err, sk->sk_err_soft);
-	} else if (saddr.ss_family == AF_INET) {
-		struct sockaddr_in *sin4 = (struct sockaddr_in *)&saddr;
 
+	inet = inet_sk(sk);
+	switch (sk->sk_family) {
+	case AF_INET:
 		printk_ratelimited(KERN_ERR "dlm: node %d: socket error "
-				   "sending to node %d at %pI4, port %d, "
+				   "sending to node %d at %pI4, dport %d, "
 				   "sk_err=%d/%d\n", dlm_our_nodeid(),
-				   con->nodeid, &sin4->sin_addr.s_addr,
-				   dlm_config.ci_tcp_port, sk->sk_err,
+				   con->nodeid, &inet->inet_daddr,
+				   ntohs(inet->inet_dport), sk->sk_err,
 				   sk->sk_err_soft);
-	} else {
-		struct sockaddr_in6 *sin6 = (struct sockaddr_in6 *)&saddr;
-
+		break;
+#if IS_ENABLED(CONFIG_IPV6)
+	case AF_INET6:
 		printk_ratelimited(KERN_ERR "dlm: node %d: socket error "
-				   "sending to node %d at %u.%u.%u.%u, "
-				   "port %d, sk_err=%d/%d\n", dlm_our_nodeid(),
-				   con->nodeid, sin6->sin6_addr.s6_addr32[0],
-				   sin6->sin6_addr.s6_addr32[1],
-				   sin6->sin6_addr.s6_addr32[2],
-				   sin6->sin6_addr.s6_addr32[3],
-				   dlm_config.ci_tcp_port, sk->sk_err,
+				   "sending to node %d at %pI6c, "
+				   "dport %d, sk_err=%d/%d\n", dlm_our_nodeid(),
+				   con->nodeid, &sk->sk_v6_daddr,
+				   ntohs(inet->inet_dport), sk->sk_err,
 				   sk->sk_err_soft);
+		break;
+#endif
+	default:
+		printk_ratelimited(KERN_ERR "dlm: node %d: socket error "
+				   "invalid socket family %d set, "
+				   "sk_err=%d/%d\n", dlm_our_nodeid(),
+				   sk->sk_family, sk->sk_err, sk->sk_err_soft);
+		goto out;
 	}
 
 	/* below sendcon only handling */
@@ -1319,6 +1319,8 @@
 		return NULL;
 	}
 
+	/* for dlm_lowcomms_commit_msg() */
+	kref_get(&msg->ref);
 	/* we assume if successful commit must called */
 	msg->idx = idx;
 	return msg;
@@ -1353,6 +1355,8 @@
 {
 	_dlm_lowcomms_commit_msg(msg);
 	srcu_read_unlock(&connections_srcu, msg->idx);
+	/* because dlm_lowcomms_new_msg() */
+	kref_put(&msg->ref, dlm_msg_release);
 }
 
 void dlm_lowcomms_put_msg(struct dlm_msg *msg)
@@ -1516,7 +1520,11 @@
 
 static void process_listen_recv_socket(struct work_struct *work)
 {
-	accept_from_sock(&listen_con);
+	int ret;
+
+	do {
+		ret = accept_from_sock(&listen_con);
+	} while (!ret);
 }
 
 static void dlm_connect(struct connection *con)
@@ -1776,7 +1784,7 @@
 				  SOCK_STREAM, dlm_proto_ops->proto, &sock);
 	if (result < 0) {
 		log_print("Can't create comms socket, check SCTP is loaded");
-		goto out;
+		return result;
 	}
 
 	sock_set_mark(sock->sk, dlm_config.ci_mark);
@@ -1793,7 +1801,7 @@
 	result = sock->ops->listen(sock, 5);
 	if (result < 0) {
 		dlm_close_sock(&listen_con.sock);
-		goto out;
+		return result;
 	}
 
 	return 0;
@@ -1951,10 +1959,6 @@
 int dlm_lowcomms_start(void)
 {
 	int error = -EINVAL;
-	int i;
-
-	for (i = 0; i < CONN_HASH_SIZE; i++)
-		INIT_HLIST_HEAD(&connection_hash[i]);
 
 	init_local();
 	if (!dlm_local_count) {
@@ -1963,8 +1967,6 @@
 		goto fail;
 	}
 
-	INIT_WORK(&listen_con.rwork, process_listen_recv_socket);
-
 	error = work_start();
 	if (error)
 		goto fail_local;
@@ -1996,7 +1998,6 @@
 	dlm_proto_ops = NULL;
 fail_proto_ops:
 	dlm_allow_conn = 0;
-	dlm_close_sock(&listen_con.sock);
 	work_stop();
 fail_local:
 	deinit_local();
@@ -2004,6 +2005,16 @@
 	return error;
 }
 
+void dlm_lowcomms_init(void)
+{
+	int i;
+
+	for (i = 0; i < CONN_HASH_SIZE; i++)
+		INIT_HLIST_HEAD(&connection_hash[i]);
+
+	INIT_WORK(&listen_con.rwork, process_listen_recv_socket);
+}
+
 void dlm_lowcomms_exit(void)
 {
 	struct dlm_node_addr *na, *safe;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/lowcomms.h
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/lowcomms.h
@@ -35,6 +35,7 @@
 int dlm_lowcomms_start(void);
 void dlm_lowcomms_shutdown(void);
 void dlm_lowcomms_stop(void);
+void dlm_lowcomms_init(void);
 void dlm_lowcomms_exit(void);
 int dlm_lowcomms_close(int nodeid);
 struct dlm_msg *dlm_lowcomms_new_msg(int nodeid, int len, gfp_t allocation,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/main.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/main.c
@@ -17,7 +17,7 @@
 #include "user.h"
 #include "memory.h"
 #include "config.h"
-#include "lowcomms.h"
+#include "midcomms.h"
 
 static int __init init_dlm(void)
 {
@@ -27,6 +27,8 @@
 	if (error)
 		goto out;
 
+	dlm_midcomms_init();
+
 	error = dlm_lockspace_init();
 	if (error)
 		goto out_mem;
@@ -63,6 +65,7 @@
  out_lockspace:
 	dlm_lockspace_exit();
  out_mem:
+	dlm_midcomms_exit();
 	dlm_memory_exit();
  out:
 	return error;
@@ -76,7 +79,7 @@
 	dlm_config_exit();
 	dlm_memory_exit();
 	dlm_lockspace_exit();
-	dlm_lowcomms_exit();
+	dlm_midcomms_exit();
 	dlm_unregister_debugfs();
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/midcomms.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/midcomms.c
@@ -366,7 +366,7 @@
 	struct dlm_msg *msg;
 	char *ppc;
 
-	msg = dlm_lowcomms_new_msg(nodeid, mb_len, GFP_NOFS, &ppc,
+	msg = dlm_lowcomms_new_msg(nodeid, mb_len, GFP_ATOMIC, &ppc,
 				   NULL, NULL);
 	if (!msg)
 		return -ENOMEM;
@@ -394,7 +394,7 @@
 	struct dlm_mhandle *mh;
 	char *ppc;
 
-	mh = dlm_midcomms_get_mhandle(node->nodeid, mb_len, GFP_NOFS, &ppc);
+	mh = dlm_midcomms_get_mhandle(node->nodeid, mb_len, GFP_ATOMIC, &ppc);
 	if (!mh)
 		return -ENOMEM;
 
@@ -478,15 +478,14 @@
 
 		switch (p->header.h_cmd) {
 		case DLM_FIN:
-			/* send ack before fin */
-			dlm_send_ack(node->nodeid, node->seq_next);
-
 			spin_lock(&node->state_lock);
 			pr_debug("receive fin msg from node %d with state %s\n",
 				 node->nodeid, dlm_state_str(node->state));
 
 			switch (node->state) {
 			case DLM_ESTABLISHED:
+				dlm_send_ack(node->nodeid, node->seq_next);
+
 				node->state = DLM_CLOSE_WAIT;
 				pr_debug("switch node %d to state %s\n",
 					 node->nodeid, dlm_state_str(node->state));
@@ -498,16 +497,19 @@
 					node->state = DLM_LAST_ACK;
 					pr_debug("switch node %d to state %s case 1\n",
 						 node->nodeid, dlm_state_str(node->state));
-					spin_unlock(&node->state_lock);
-					goto send_fin;
+					set_bit(DLM_NODE_FLAG_STOP_RX, &node->flags);
+					dlm_send_fin(node, dlm_pas_fin_ack_rcv);
 				}
 				break;
 			case DLM_FIN_WAIT1:
+				dlm_send_ack(node->nodeid, node->seq_next);
 				node->state = DLM_CLOSING;
+				set_bit(DLM_NODE_FLAG_STOP_RX, &node->flags);
 				pr_debug("switch node %d to state %s\n",
 					 node->nodeid, dlm_state_str(node->state));
 				break;
 			case DLM_FIN_WAIT2:
+				dlm_send_ack(node->nodeid, node->seq_next);
 				midcomms_node_reset(node);
 				pr_debug("switch node %d to state %s\n",
 					 node->nodeid, dlm_state_str(node->state));
@@ -524,8 +526,6 @@
 				return;
 			}
 			spin_unlock(&node->state_lock);
-
-			set_bit(DLM_NODE_FLAG_STOP_RX, &node->flags);
 			break;
 		default:
 			WARN_ON(test_bit(DLM_NODE_FLAG_STOP_RX, &node->flags));
@@ -543,12 +543,6 @@
 		log_print_ratelimited("ignore dlm msg because seq mismatch, seq: %u, expected: %u, nodeid: %d",
 				      seq, node->seq_next, node->nodeid);
 	}
-
-	return;
-
-send_fin:
-	set_bit(DLM_NODE_FLAG_STOP_RX, &node->flags);
-	dlm_send_fin(node, dlm_pas_fin_ack_rcv);
 }
 
 static struct midcomms_node *
@@ -1149,12 +1143,27 @@
 
 int dlm_midcomms_start(void)
 {
+	return dlm_lowcomms_start();
+}
+
+void dlm_midcomms_stop(void)
+{
+	dlm_lowcomms_stop();
+}
+
+void dlm_midcomms_init(void)
+{
 	int i;
 
 	for (i = 0; i < CONN_HASH_SIZE; i++)
 		INIT_HLIST_HEAD(&node_hash[i]);
 
-	return dlm_lowcomms_start();
+	dlm_lowcomms_init();
+}
+
+void dlm_midcomms_exit(void)
+{
+	dlm_lowcomms_exit();
 }
 
 static void dlm_act_fin_ack_rcv(struct midcomms_node *node)
@@ -1269,11 +1278,11 @@
 		case DLM_CLOSE_WAIT:
 			/* passive shutdown DLM_LAST_ACK case 2 */
 			node->state = DLM_LAST_ACK;
-			spin_unlock(&node->state_lock);
-
 			pr_debug("switch node %d to state %s case 2\n",
 				 node->nodeid, dlm_state_str(node->state));
-			goto send_fin;
+			set_bit(DLM_NODE_FLAG_STOP_RX, &node->flags);
+			dlm_send_fin(node, dlm_pas_fin_ack_rcv);
+			break;
 		case DLM_LAST_ACK:
 			/* probably receive fin caught it, do nothing */
 			break;
@@ -1289,12 +1298,6 @@
 	spin_unlock(&node->state_lock);
 
 	srcu_read_unlock(&nodes_srcu, idx);
-	return;
-
-send_fin:
-	set_bit(DLM_NODE_FLAG_STOP_RX, &node->flags);
-	dlm_send_fin(node, dlm_pas_fin_ack_rcv);
-	srcu_read_unlock(&nodes_srcu, idx);
 }
 
 static void midcomms_node_release(struct rcu_head *rcu)
@@ -1325,6 +1328,7 @@
 		node->state = DLM_FIN_WAIT1;
 		pr_debug("switch node %d to state %s case 2\n",
 			 node->nodeid, dlm_state_str(node->state));
+		dlm_send_fin(node, dlm_act_fin_ack_rcv);
 		break;
 	case DLM_CLOSED:
 		/* we have what we want */
@@ -1338,12 +1342,8 @@
 	}
 	spin_unlock(&node->state_lock);
 
-	if (node->state == DLM_FIN_WAIT1) {
-		dlm_send_fin(node, dlm_act_fin_ack_rcv);
-
-		if (DLM_DEBUG_FENCE_TERMINATION)
-			msleep(5000);
-	}
+	if (DLM_DEBUG_FENCE_TERMINATION)
+		msleep(5000);
 
 	/* wait for other side dlm + fin */
 	ret = wait_event_timeout(node->shutdown_wait,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/midcomms.h
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/midcomms.h
@@ -20,6 +20,9 @@
 void dlm_midcomms_commit_mhandle(struct dlm_mhandle *mh);
 int dlm_midcomms_close(int nodeid);
 int dlm_midcomms_start(void);
+void dlm_midcomms_stop(void);
+void dlm_midcomms_init(void);
+void dlm_midcomms_exit(void);
 void dlm_midcomms_shutdown(void);
 void dlm_midcomms_add_member(int nodeid);
 void dlm_midcomms_remove_member(int nodeid);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/plock.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/plock.c
@@ -19,20 +19,20 @@
 static wait_queue_head_t send_wq;
 static wait_queue_head_t recv_wq;
 
-struct plock_op {
-	struct list_head list;
-	int done;
-	struct dlm_plock_info info;
-};
-
-struct plock_xop {
-	struct plock_op xop;
-	int (*callback)(struct file_lock *fl, int result);
+struct plock_async_data {
 	void *fl;
 	void *file;
 	struct file_lock flc;
+	int (*callback)(struct file_lock *fl, int result);
 };
 
+struct plock_op {
+	struct list_head list;
+	int done;
+	struct dlm_plock_info info;
+	/* if set indicates async handling */
+	struct plock_async_data *data;
+};
 
 static inline void set_version(struct dlm_plock_info *info)
 {
@@ -58,6 +58,12 @@
 	return 0;
 }
 
+static void dlm_release_plock_op(struct plock_op *op)
+{
+	kfree(op->data);
+	kfree(op);
+}
+
 static void send_op(struct plock_op *op)
 {
 	set_version(&op->info);
@@ -74,8 +80,7 @@
    abandoned waiter.  So, we have to insert the unlock-close when the
    lock call is interrupted. */
 
-static void do_unlock_close(struct dlm_ls *ls, u64 number,
-			    struct file *file, struct file_lock *fl)
+static void do_unlock_close(const struct dlm_plock_info *info)
 {
 	struct plock_op *op;
 
@@ -84,15 +89,12 @@
 		return;
 
 	op->info.optype		= DLM_PLOCK_OP_UNLOCK;
-	op->info.pid		= fl->fl_pid;
-	op->info.fsid		= ls->ls_global_id;
-	op->info.number		= number;
+	op->info.pid		= info->pid;
+	op->info.fsid		= info->fsid;
+	op->info.number		= info->number;
 	op->info.start		= 0;
 	op->info.end		= OFFSET_MAX;
-	if (fl->fl_lmops && fl->fl_lmops->lm_grant)
-		op->info.owner	= (__u64) fl->fl_pid;
-	else
-		op->info.owner	= (__u64)(long) fl->fl_owner;
+	op->info.owner		= info->owner;
 
 	op->info.flags |= DLM_PLOCK_FL_CLOSE;
 	send_op(op);
@@ -101,22 +103,21 @@
 int dlm_posix_lock(dlm_lockspace_t *lockspace, u64 number, struct file *file,
 		   int cmd, struct file_lock *fl)
 {
+	struct plock_async_data *op_data;
 	struct dlm_ls *ls;
 	struct plock_op *op;
-	struct plock_xop *xop;
 	int rv;
 
 	ls = dlm_find_lockspace_local(lockspace);
 	if (!ls)
 		return -EINVAL;
 
-	xop = kzalloc(sizeof(*xop), GFP_NOFS);
-	if (!xop) {
+	op = kzalloc(sizeof(*op), GFP_NOFS);
+	if (!op) {
 		rv = -ENOMEM;
 		goto out;
 	}
 
-	op = &xop->xop;
 	op->info.optype		= DLM_PLOCK_OP_LOCK;
 	op->info.pid		= fl->fl_pid;
 	op->info.ex		= (fl->fl_type == F_WRLCK);
@@ -125,36 +126,45 @@
 	op->info.number		= number;
 	op->info.start		= fl->fl_start;
 	op->info.end		= fl->fl_end;
+	/* async handling */
 	if (fl->fl_lmops && fl->fl_lmops->lm_grant) {
+		op_data = kzalloc(sizeof(*op_data), GFP_NOFS);
+		if (!op_data) {
+			dlm_release_plock_op(op);
+			rv = -ENOMEM;
+			goto out;
+		}
+
 		/* fl_owner is lockd which doesn't distinguish
 		   processes on the nfs client */
 		op->info.owner	= (__u64) fl->fl_pid;
-		xop->callback	= fl->fl_lmops->lm_grant;
-		locks_init_lock(&xop->flc);
-		locks_copy_lock(&xop->flc, fl);
-		xop->fl		= fl;
-		xop->file	= file;
+		op_data->callback = fl->fl_lmops->lm_grant;
+		locks_init_lock(&op_data->flc);
+		locks_copy_lock(&op_data->flc, fl);
+		op_data->fl		= fl;
+		op_data->file	= file;
+
+		op->data = op_data;
+
+		send_op(op);
+		rv = FILE_LOCK_DEFERRED;
+		goto out;
 	} else {
 		op->info.owner	= (__u64)(long) fl->fl_owner;
-		xop->callback	= NULL;
 	}
 
 	send_op(op);
 
-	if (xop->callback == NULL) {
-		rv = wait_event_interruptible(recv_wq, (op->done != 0));
-		if (rv == -ERESTARTSYS) {
-			log_debug(ls, "dlm_posix_lock: wait killed %llx",
-				  (unsigned long long)number);
-			spin_lock(&ops_lock);
-			list_del(&op->list);
-			spin_unlock(&ops_lock);
-			kfree(xop);
-			do_unlock_close(ls, number, file, fl);
-			goto out;
-		}
-	} else {
-		rv = FILE_LOCK_DEFERRED;
+	rv = wait_event_killable(recv_wq, (op->done != 0));
+	if (rv == -ERESTARTSYS) {
+		spin_lock(&ops_lock);
+		list_del(&op->list);
+		spin_unlock(&ops_lock);
+		log_debug(ls, "%s: wait interrupted %x %llx pid %d",
+			  __func__, ls->ls_global_id,
+			  (unsigned long long)number, op->info.pid);
+		dlm_release_plock_op(op);
+		do_unlock_close(&op->info);
 		goto out;
 	}
 
@@ -174,7 +184,7 @@
 				  (unsigned long long)number);
 	}
 
-	kfree(xop);
+	dlm_release_plock_op(op);
 out:
 	dlm_put_lockspace(ls);
 	return rv;
@@ -184,11 +194,11 @@
 /* Returns failure iff a successful lock operation should be canceled */
 static int dlm_plock_callback(struct plock_op *op)
 {
+	struct plock_async_data *op_data = op->data;
 	struct file *file;
 	struct file_lock *fl;
 	struct file_lock *flc;
 	int (*notify)(struct file_lock *fl, int result) = NULL;
-	struct plock_xop *xop = (struct plock_xop *)op;
 	int rv = 0;
 
 	spin_lock(&ops_lock);
@@ -200,10 +210,10 @@
 	spin_unlock(&ops_lock);
 
 	/* check if the following 2 are still valid or make a copy */
-	file = xop->file;
-	flc = &xop->flc;
-	fl = xop->fl;
-	notify = xop->callback;
+	file = op_data->file;
+	flc = &op_data->flc;
+	fl = op_data->fl;
+	notify = op_data->callback;
 
 	if (op->info.rv) {
 		notify(fl, op->info.rv);
@@ -234,7 +244,7 @@
 	}
 
 out:
-	kfree(xop);
+	dlm_release_plock_op(op);
 	return rv;
 }
 
@@ -304,7 +314,7 @@
 		rv = 0;
 
 out_free:
-	kfree(op);
+	dlm_release_plock_op(op);
 out:
 	dlm_put_lockspace(ls);
 	fl->fl_flags = fl_flags;
@@ -364,13 +374,15 @@
 		locks_init_lock(fl);
 		fl->fl_type = (op->info.ex) ? F_WRLCK : F_RDLCK;
 		fl->fl_flags = FL_POSIX;
-		fl->fl_pid = -op->info.pid;
+		fl->fl_pid = op->info.pid;
+		if (op->info.nodeid != dlm_our_nodeid())
+			fl->fl_pid = -fl->fl_pid;
 		fl->fl_start = op->info.start;
 		fl->fl_end = op->info.end;
 		rv = 0;
 	}
 
-	kfree(op);
+	dlm_release_plock_op(op);
 out:
 	dlm_put_lockspace(ls);
 	return rv;
@@ -393,7 +405,7 @@
 		if (op->info.flags & DLM_PLOCK_FL_CLOSE)
 			list_del(&op->list);
 		else
-			list_move(&op->list, &recv_list);
+			list_move_tail(&op->list, &recv_list);
 		memcpy(&info, &op->info, sizeof(info));
 	}
 	spin_unlock(&ops_lock);
@@ -406,7 +418,7 @@
 	   (the process did not make an unlock call). */
 
 	if (op->info.flags & DLM_PLOCK_FL_CLOSE)
-		kfree(op);
+		dlm_release_plock_op(op);
 
 	if (copy_to_user(u, &info, sizeof(info)))
 		return -EFAULT;
@@ -418,9 +430,9 @@
 static ssize_t dev_write(struct file *file, const char __user *u, size_t count,
 			 loff_t *ppos)
 {
+	struct plock_op *op = NULL, *iter;
 	struct dlm_plock_info info;
-	struct plock_op *op;
-	int found = 0, do_callback = 0;
+	int do_callback = 0;
 
 	if (count != sizeof(info))
 		return -EINVAL;
@@ -431,32 +443,63 @@
 	if (check_version(&info))
 		return -EINVAL;
 
+	/*
+	 * The results for waiting ops (SETLKW) can be returned in any
+	 * order, so match all fields to find the op.  The results for
+	 * non-waiting ops are returned in the order that they were sent
+	 * to userspace, so match the result with the first non-waiting op.
+	 */
 	spin_lock(&ops_lock);
-	list_for_each_entry(op, &recv_list, list) {
-		if (op->info.fsid == info.fsid &&
-		    op->info.number == info.number &&
-		    op->info.owner == info.owner) {
-			struct plock_xop *xop = (struct plock_xop *)op;
-			list_del_init(&op->list);
-			memcpy(&op->info, &info, sizeof(info));
-			if (xop->callback)
-				do_callback = 1;
-			else
-				op->done = 1;
-			found = 1;
-			break;
+	if (info.wait) {
+		list_for_each_entry(iter, &recv_list, list) {
+			if (iter->info.fsid == info.fsid &&
+			    iter->info.number == info.number &&
+			    iter->info.owner == info.owner &&
+			    iter->info.pid == info.pid &&
+			    iter->info.start == info.start &&
+			    iter->info.end == info.end &&
+			    iter->info.ex == info.ex &&
+			    iter->info.wait) {
+				op = iter;
+				break;
+			}
 		}
+	} else {
+		list_for_each_entry(iter, &recv_list, list) {
+			if (!iter->info.wait &&
+			    iter->info.fsid == info.fsid) {
+				op = iter;
+				break;
+			}
+		}
+	}
+
+	if (op) {
+		/* Sanity check that op and info match. */
+		if (info.wait)
+			WARN_ON(op->info.optype != DLM_PLOCK_OP_LOCK);
+		else
+			WARN_ON(op->info.number != info.number ||
+				op->info.owner != info.owner ||
+				op->info.optype != info.optype);
+
+		list_del_init(&op->list);
+		memcpy(&op->info, &info, sizeof(info));
+		if (op->data)
+			do_callback = 1;
+		else
+			op->done = 1;
 	}
 	spin_unlock(&ops_lock);
 
-	if (found) {
+	if (op) {
 		if (do_callback)
 			dlm_plock_callback(op);
 		else
 			wake_up(&recv_wq);
 	} else
-		log_print("dev_write no op %x %llx", info.fsid,
-			  (unsigned long long)info.number);
+		log_print("%s: no op %x %llx", __func__,
+			  info.fsid, (unsigned long long)info.number);
 	return count;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/dlm/recover.c
+++ linux-xilinx-zynqmp-5.15.0/fs/dlm/recover.c
@@ -732,10 +732,9 @@
 
 static void recover_lvb(struct dlm_rsb *r)
 {
-	struct dlm_lkb *lkb, *high_lkb = NULL;
+	struct dlm_lkb *big_lkb = NULL, *iter, *high_lkb = NULL;
 	uint32_t high_seq = 0;
 	int lock_lvb_exists = 0;
-	int big_lock_exists = 0;
 	int lvblen = r->res_ls->ls_lvblen;
 
 	if (!rsb_flag(r, RSB_NEW_MASTER2) &&
@@ -751,37 +750,37 @@
 	/* we are the new master, so figure out if VALNOTVALID should
 	   be set, and set the rsb lvb from the best lkb available. */
 
-	list_for_each_entry(lkb, &r->res_grantqueue, lkb_statequeue) {
-		if (!(lkb->lkb_exflags & DLM_LKF_VALBLK))
+	list_for_each_entry(iter, &r->res_grantqueue, lkb_statequeue) {
+		if (!(iter->lkb_exflags & DLM_LKF_VALBLK))
 			continue;
 
 		lock_lvb_exists = 1;
 
-		if (lkb->lkb_grmode > DLM_LOCK_CR) {
-			big_lock_exists = 1;
+		if (iter->lkb_grmode > DLM_LOCK_CR) {
+			big_lkb = iter;
 			goto setflag;
 		}
 
-		if (((int)lkb->lkb_lvbseq - (int)high_seq) >= 0) {
-			high_lkb = lkb;
-			high_seq = lkb->lkb_lvbseq;
+		if (((int)iter->lkb_lvbseq - (int)high_seq) >= 0) {
+			high_lkb = iter;
+			high_seq = iter->lkb_lvbseq;
 		}
 	}
 
-	list_for_each_entry(lkb, &r->res_convertqueue, lkb_statequeue) {
-		if (!(lkb->lkb_exflags & DLM_LKF_VALBLK))
+	list_for_each_entry(iter, &r->res_convertqueue, lkb_statequeue) {
+		if (!(iter->lkb_exflags & DLM_LKF_VALBLK))
 			continue;
 
 		lock_lvb_exists = 1;
 
-		if (lkb->lkb_grmode > DLM_LOCK_CR) {
-			big_lock_exists = 1;
+		if (iter->lkb_grmode > DLM_LOCK_CR) {
+			big_lkb = iter;
 			goto setflag;
 		}
 
-		if (((int)lkb->lkb_lvbseq - (int)high_seq) >= 0) {
-			high_lkb = lkb;
-			high_seq = lkb->lkb_lvbseq;
+		if (((int)iter->lkb_lvbseq - (int)high_seq) >= 0) {
+			high_lkb = iter;
+			high_seq = iter->lkb_lvbseq;
 		}
 	}
 
@@ -790,7 +789,7 @@
 		goto out;
 
 	/* lvb is invalidated if only NL/CR locks remain */
-	if (!big_lock_exists)
+	if (!big_lkb)
 		rsb_set_flag(r, RSB_VALNOTVALID);
 
 	if (!r->res_lvbptr) {
@@ -799,9 +798,9 @@
 			goto out;
 	}
 
-	if (big_lock_exists) {
-		r->res_lvbseq = lkb->lkb_lvbseq;
-		memcpy(r->res_lvbptr, lkb->lkb_lvbptr, lvblen);
+	if (big_lkb) {
+		r->res_lvbseq = big_lkb->lkb_lvbseq;
+		memcpy(r->res_lvbptr, big_lkb->lkb_lvbptr, lvblen);
 	} else if (high_lkb) {
 		r->res_lvbseq = high_lkb->lkb_lvbseq;
 		memcpy(r->res_lvbptr, high_lkb->lkb_lvbptr, lvblen);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ecryptfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ecryptfs/inode.c
@@ -76,6 +76,14 @@
 
 	if (lower_inode->i_sb != ecryptfs_superblock_to_lower(sb))
 		return ERR_PTR(-EXDEV);
+
+	/* Reject dealing with casefold directories. */
+	if (IS_CASEFOLDED(lower_inode)) {
+		pr_err_ratelimited("%s: Can't handle casefolded directory.\n",
+				   __func__);
+		return ERR_PTR(-EREMOTE);
+	}
+
 	if (!igrab(lower_inode))
 		return ERR_PTR(-ESTALE);
 	inode = iget5_locked(sb, (unsigned long)lower_inode,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ecryptfs/keystore.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ecryptfs/keystore.c
@@ -300,9 +300,11 @@
 	 *         | Key Identifier Size      | 1 or 2 bytes |
 	 *         | Key Identifier           | arbitrary    |
 	 *         | File Encryption Key Size | 1 or 2 bytes |
+	 *         | Cipher Code              | 1 byte       |
 	 *         | File Encryption Key      | arbitrary    |
+	 *         | Checksum                 | 2 bytes      |
 	 */
-	data_len = (5 + ECRYPTFS_SIG_SIZE_HEX + crypt_stat->key_size);
+	data_len = (8 + ECRYPTFS_SIG_SIZE_HEX + crypt_stat->key_size);
 	*packet = kmalloc(data_len, GFP_KERNEL);
 	message = *packet;
 	if (!message) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ecryptfs/main.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ecryptfs/main.c
@@ -537,7 +537,7 @@
 		goto out_free;
 	}
 
-	if (mnt_user_ns(path.mnt) != &init_user_ns) {
+	if (is_idmapped_mnt(path.mnt)) {
 		rc = -EINVAL;
 		printk(KERN_ERR "Mounting on idmapped mounts currently disallowed\n");
 		goto out_free;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/efivarfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/efivarfs/inode.c
@@ -47,7 +47,7 @@
  *
  *	VariableName-12345678-1234-1234-1234-1234567891bc
  */
-bool efivarfs_valid_name(const char *str, int len)
+static bool efivarfs_valid_name(const char *str, int len)
 {
 	const char *s = str + len - EFI_VARIABLE_GUID_LEN;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/efivarfs/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/efivarfs/internal.h
@@ -10,7 +10,6 @@
 
 extern const struct file_operations efivarfs_file_operations;
 extern const struct inode_operations efivarfs_dir_inode_operations;
-extern bool efivarfs_valid_name(const char *str, int len);
 extern struct inode *efivarfs_get_inode(struct super_block *sb,
 			const struct inode *dir, int mode, dev_t dev,
 			bool is_removable);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/efivarfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/efivarfs/super.c
@@ -13,6 +13,7 @@
 #include <linux/ucs2_string.h>
 #include <linux/slab.h>
 #include <linux/magic.h>
+#include <linux/printk.h>
 
 #include "internal.h"
 
@@ -63,9 +64,6 @@
 	const unsigned char *s = qstr->name;
 	unsigned int len = qstr->len;
 
-	if (!efivarfs_valid_name(s, len))
-		return -EINVAL;
-
 	while (len-- > EFI_VARIABLE_GUID_LEN)
 		hash = partial_name_hash(*s++, hash);
 
@@ -231,8 +229,19 @@
 	return get_tree_single(fc, efivarfs_fill_super);
 }
 
+static int efivarfs_reconfigure(struct fs_context *fc)
+{
+	if (!efivar_supports_writes() && !(fc->sb_flags & SB_RDONLY)) {
+		pr_err("Firmware does not support SetVariableRT. Can not remount with rw\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static const struct fs_context_operations efivarfs_context_ops = {
 	.get_tree	= efivarfs_get_tree,
+	.reconfigure	= efivarfs_reconfigure,
 };
 
 static int efivarfs_init_fs_context(struct fs_context *fc)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/data.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/data.c
@@ -287,7 +287,7 @@
 
 		if (!err)
 			return iomap_dio_rw(iocb, to, &erofs_iomap_ops,
-					    NULL, 0);
+					    NULL, 0, 0);
 		if (err < 0)
 			return err;
 	}
@@ -340,4 +340,5 @@
 	.read_iter	= erofs_file_read_iter,
 	.mmap		= erofs_file_mmap,
 	.splice_read	= generic_file_splice_read,
+	.get_unmapped_area = thp_get_unmapped_area,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/decompressor.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/decompressor.c
@@ -93,14 +93,18 @@
 
 		if (page) {
 			__clear_bit(j, bounced);
-			if (kaddr) {
-				if (kaddr + PAGE_SIZE == page_address(page))
+			if (!PageHighMem(page)) {
+				if (!i) {
+					kaddr = page_address(page);
+					continue;
+				}
+				if (kaddr &&
+				    kaddr + PAGE_SIZE == page_address(page)) {
 					kaddr += PAGE_SIZE;
-				else
-					kaddr = NULL;
-			} else if (!i) {
-				kaddr = page_address(page);
+					continue;
+				}
 			}
+			kaddr = NULL;
 			continue;
 		}
 		kaddr = NULL;
@@ -120,11 +124,11 @@
 }
 
 static void *z_erofs_handle_inplace_io(struct z_erofs_decompress_req *rq,
-			void *inpage, unsigned int *inputmargin, int *maptype,
-			bool support_0padding)
+		void *inpage, void *out, unsigned int *inputmargin, int *maptype,
+		bool support_0padding)
 {
 	unsigned int nrpages_in, nrpages_out;
-	unsigned int ofull, oend, inputsize, total, i, j;
+	unsigned int ofull, oend, inputsize, total, i;
 	struct page **in;
 	void *src, *tmp;
 
@@ -139,12 +143,13 @@
 		    ofull - oend < LZ4_DECOMPRESS_INPLACE_MARGIN(inputsize))
 			goto docopy;
 
-		for (i = 0; i < nrpages_in; ++i) {
-			DBG_BUGON(rq->in[i] == NULL);
-			for (j = 0; j < nrpages_out - nrpages_in + i; ++j)
-				if (rq->out[j] == rq->in[i])
-					goto docopy;
-		}
+		for (i = 0; i < nrpages_in; ++i)
+			if (rq->out[nrpages_out - nrpages_in + i] !=
+			    rq->in[i])
+				goto docopy;
+		kunmap_atomic(inpage);
+		*maptype = 3;
+		return out + ((nrpages_out - nrpages_in) << PAGE_SHIFT);
 	}
 
 	if (nrpages_in <= 1) {
@@ -152,7 +157,6 @@
 		return inpage;
 	}
 	kunmap_atomic(inpage);
-	might_sleep();
 	src = erofs_vm_map_ram(rq->in, nrpages_in);
 	if (!src)
 		return ERR_PTR(-ENOMEM);
@@ -189,10 +193,10 @@
 	return src;
 }
 
-static int z_erofs_lz4_decompress(struct z_erofs_decompress_req *rq, u8 *out)
+static int z_erofs_lz4_decompress(struct z_erofs_decompress_req *rq, u8 *dst)
 {
 	unsigned int inputmargin;
-	u8 *headpage, *src;
+	u8 *out, *headpage, *src;
 	bool support_0padding;
 	int ret, maptype;
 
@@ -216,11 +220,12 @@
 	}
 
 	rq->inputsize -= inputmargin;
-	src = z_erofs_handle_inplace_io(rq, headpage, &inputmargin, &maptype,
-					support_0padding);
+	src = z_erofs_handle_inplace_io(rq, headpage, dst, &inputmargin,
+					&maptype, support_0padding);
 	if (IS_ERR(src))
 		return PTR_ERR(src);
 
+	out = dst + rq->pageofs_out;
 	/* legacy format could compress extra data in a pcluster. */
 	if (rq->partial_decoding || !support_0padding)
 		ret = LZ4_decompress_safe_partial(src + inputmargin, out,
@@ -233,7 +238,6 @@
 		erofs_err(rq->sb, "failed to decompress %d in[%u, %u] out[%u]",
 			  ret, rq->inputsize, inputmargin, rq->outputsize);
 
-		WARN_ON(1);
 		print_hex_dump(KERN_DEBUG, "[ in]: ", DUMP_PREFIX_OFFSET,
 			       16, 1, src + inputmargin, rq->inputsize, true);
 		print_hex_dump(KERN_DEBUG, "[out]: ", DUMP_PREFIX_OFFSET,
@@ -250,7 +254,7 @@
 		vm_unmap_ram(src, PAGE_ALIGN(rq->inputsize) >> PAGE_SHIFT);
 	} else if (maptype == 2) {
 		erofs_put_pcpubuf(src);
-	} else {
+	} else if (maptype != 3) {
 		DBG_BUGON(1);
 		return -EFAULT;
 	}
@@ -351,8 +355,7 @@
 	dst_maptype = 2;
 
 dstmap_out:
-	ret = alg->decompress(rq, dst + rq->pageofs_out);
-
+	ret = alg->decompress(rq, dst);
 	if (!dst_maptype)
 		kunmap_atomic(dst);
 	else if (dst_maptype == 2)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/inode.c
@@ -192,8 +192,9 @@
 	inode->i_atime.tv_nsec = inode->i_ctime.tv_nsec;
 
 	inode->i_flags &= ~S_DAX;
-	if (test_opt(&sbi->ctx, DAX_ALWAYS) && S_ISREG(inode->i_mode) &&
-	    vi->datalayout == EROFS_INODE_FLAT_PLAIN)
+	if (test_opt(&sbi->opt, DAX_ALWAYS) && S_ISREG(inode->i_mode) &&
+	    (vi->datalayout == EROFS_INODE_FLAT_PLAIN ||
+	     vi->datalayout == EROFS_INODE_CHUNK_BASED))
 		inode->i_flags |= S_DAX;
 	if (!nblks)
 		/* measure inode.i_blocks as generic filesystems */
@@ -218,11 +219,14 @@
 			      unsigned int m_pofs)
 {
 	struct erofs_inode *vi = EROFS_I(inode);
+	loff_t off;
 	char *lnk;
 
-	/* if it cannot be handled with fast symlink scheme */
-	if (vi->datalayout != EROFS_INODE_FLAT_INLINE ||
-	    inode->i_size >= PAGE_SIZE) {
+	m_pofs += vi->xattr_isize;
+	/* check if it cannot be handled with fast symlink scheme */
+	if (vi->datalayout != EROFS_INODE_FLAT_INLINE || inode->i_size < 0 ||
+	    check_add_overflow(m_pofs, inode->i_size, &off) ||
+	    off > i_blocksize(inode)) {
 		inode->i_op = &erofs_symlink_iops;
 		return 0;
 	}
@@ -231,17 +235,6 @@
 	if (!lnk)
 		return -ENOMEM;
 
-	m_pofs += vi->xattr_isize;
-	/* inline symlink data shouldn't cross page boundary as well */
-	if (m_pofs + inode->i_size > PAGE_SIZE) {
-		kfree(lnk);
-		erofs_err(inode->i_sb,
-			  "inline data cross block boundary @ nid %llu",
-			  vi->nid);
-		DBG_BUGON(1);
-		return -EFSCORRUPTED;
-	}
-
 	memcpy(lnk, data + m_pofs, inode->i_size);
 	lnk[inode->i_size] = '\0';
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/internal.h
@@ -47,7 +47,7 @@
 /* data type for filesystem-wide blocks number */
 typedef u32 erofs_blk_t;
 
-struct erofs_fs_context {
+struct erofs_mount_opts {
 #ifdef CONFIG_EROFS_FS_ZIP
 	/* current strategy of how to use managed cache */
 	unsigned char cache_strategy;
@@ -60,6 +60,10 @@
 	unsigned int mount_opt;
 };
 
+struct erofs_fs_context {
+	struct erofs_mount_opts opt;
+};
+
 /* all filesystem-wide lz4 configurations */
 struct erofs_sb_lz4_info {
 	/* # of pages needed for EROFS lz4 rolling decompression */
@@ -69,6 +73,8 @@
 };
 
 struct erofs_sb_info {
+	struct erofs_mount_opts opt;	/* options */
+
 #ifdef CONFIG_EROFS_FS_ZIP
 	/* list for all registered superblocks, mainly for shrinker */
 	struct list_head list;
@@ -108,8 +114,6 @@
 	u8 volume_name[16];             /* volume name */
 	u32 feature_compat;
 	u32 feature_incompat;
-
-	struct erofs_fs_context ctx;	/* options */
 };
 
 #define EROFS_SB(sb) ((struct erofs_sb_info *)(sb)->s_fs_info)
@@ -121,9 +125,9 @@
 #define EROFS_MOUNT_DAX_ALWAYS		0x00000040
 #define EROFS_MOUNT_DAX_NEVER		0x00000080
 
-#define clear_opt(ctx, option)	((ctx)->mount_opt &= ~EROFS_MOUNT_##option)
-#define set_opt(ctx, option)	((ctx)->mount_opt |= EROFS_MOUNT_##option)
-#define test_opt(ctx, option)	((ctx)->mount_opt & EROFS_MOUNT_##option)
+#define clear_opt(opt, option)	((opt)->mount_opt &= ~EROFS_MOUNT_##option)
+#define set_opt(opt, option)	((opt)->mount_opt |= EROFS_MOUNT_##option)
+#define test_opt(opt, option)	((opt)->mount_opt & EROFS_MOUNT_##option)
 
 enum {
 	EROFS_ZIP_CACHE_DISABLED,
@@ -143,7 +147,6 @@
 	atomic_t refcount;
 };
 
-#if defined(CONFIG_SMP)
 static inline bool erofs_workgroup_try_to_freeze(struct erofs_workgroup *grp,
 						 int val)
 {
@@ -172,34 +175,6 @@
 	return atomic_cond_read_relaxed(&grp->refcount,
 					VAL != EROFS_LOCKED_MAGIC);
 }
-#else
-static inline bool erofs_workgroup_try_to_freeze(struct erofs_workgroup *grp,
-						 int val)
-{
-	preempt_disable();
-	/* no need to spin on UP platforms, let's just disable preemption. */
-	if (val != atomic_read(&grp->refcount)) {
-		preempt_enable();
-		return false;
-	}
-	return true;
-}
-
-static inline void erofs_workgroup_unfreeze(struct erofs_workgroup *grp,
-					    int orig_val)
-{
-	preempt_enable();
-}
-
-static inline int erofs_wait_on_workgroup_freezed(struct erofs_workgroup *grp)
-{
-	int v = atomic_read(&grp->refcount);
-
-	/* workgroup is never freezed on uniprocessor systems */
-	DBG_BUGON(v == EROFS_LOCKED_MAGIC);
-	return v;
-}
-#endif	/* !CONFIG_SMP */
 #endif	/* !CONFIG_EROFS_FS_ZIP */
 
 /* we strictly follow PAGE_SIZE and no buffer head yet */
@@ -255,7 +230,7 @@
 
 	unsigned char datalayout;
 	unsigned char inode_isize;
-	unsigned short xattr_isize;
+	unsigned int xattr_isize;
 
 	unsigned int xattr_shared_count;
 	unsigned int *xattr_shared_xattrs;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/super.c
@@ -340,15 +340,15 @@
 static void erofs_default_options(struct erofs_fs_context *ctx)
 {
 #ifdef CONFIG_EROFS_FS_ZIP
-	ctx->cache_strategy = EROFS_ZIP_CACHE_READAROUND;
-	ctx->max_sync_decompress_pages = 3;
-	ctx->readahead_sync_decompress = false;
+	ctx->opt.cache_strategy = EROFS_ZIP_CACHE_READAROUND;
+	ctx->opt.max_sync_decompress_pages = 3;
+	ctx->opt.readahead_sync_decompress = false;
 #endif
 #ifdef CONFIG_EROFS_FS_XATTR
-	set_opt(ctx, XATTR_USER);
+	set_opt(&ctx->opt, XATTR_USER);
 #endif
 #ifdef CONFIG_EROFS_FS_POSIX_ACL
-	set_opt(ctx, POSIX_ACL);
+	set_opt(&ctx->opt, POSIX_ACL);
 #endif
 }
 
@@ -392,12 +392,12 @@
 	switch (mode) {
 	case EROFS_MOUNT_DAX_ALWAYS:
 		warnfc(fc, "DAX enabled. Warning: EXPERIMENTAL, use at your own risk");
-		set_opt(ctx, DAX_ALWAYS);
-		clear_opt(ctx, DAX_NEVER);
+		set_opt(&ctx->opt, DAX_ALWAYS);
+		clear_opt(&ctx->opt, DAX_NEVER);
 		return true;
 	case EROFS_MOUNT_DAX_NEVER:
-		set_opt(ctx, DAX_NEVER);
-		clear_opt(ctx, DAX_ALWAYS);
+		set_opt(&ctx->opt, DAX_NEVER);
+		clear_opt(&ctx->opt, DAX_ALWAYS);
 		return true;
 	default:
 		DBG_BUGON(1);
@@ -424,9 +424,9 @@
 	case Opt_user_xattr:
 #ifdef CONFIG_EROFS_FS_XATTR
 		if (result.boolean)
-			set_opt(ctx, XATTR_USER);
+			set_opt(&ctx->opt, XATTR_USER);
 		else
-			clear_opt(ctx, XATTR_USER);
+			clear_opt(&ctx->opt, XATTR_USER);
 #else
 		errorfc(fc, "{,no}user_xattr options not supported");
 #endif
@@ -434,16 +434,16 @@
 	case Opt_acl:
 #ifdef CONFIG_EROFS_FS_POSIX_ACL
 		if (result.boolean)
-			set_opt(ctx, POSIX_ACL);
+			set_opt(&ctx->opt, POSIX_ACL);
 		else
-			clear_opt(ctx, POSIX_ACL);
+			clear_opt(&ctx->opt, POSIX_ACL);
 #else
 		errorfc(fc, "{,no}acl options not supported");
 #endif
 		break;
 	case Opt_cache_strategy:
 #ifdef CONFIG_EROFS_FS_ZIP
-		ctx->cache_strategy = result.uint_32;
+		ctx->opt.cache_strategy = result.uint_32;
 #else
 		errorfc(fc, "compression not supported, cache_strategy ignored");
 #endif
@@ -540,15 +540,16 @@
 		return -ENOMEM;
 
 	sb->s_fs_info = sbi;
+	sbi->opt = ctx->opt;
 	sbi->dax_dev = fs_dax_get_by_bdev(sb->s_bdev);
 	err = erofs_read_superblock(sb);
 	if (err)
 		return err;
 
-	if (test_opt(ctx, DAX_ALWAYS) &&
+	if (test_opt(&sbi->opt, DAX_ALWAYS) &&
 	    !dax_supported(sbi->dax_dev, sb->s_bdev, EROFS_BLKSIZ, 0, bdev_nr_sectors(sb->s_bdev))) {
 		errorfc(fc, "DAX unsupported by block device. Turning off DAX.");
-		clear_opt(ctx, DAX_ALWAYS);
+		clear_opt(&sbi->opt, DAX_ALWAYS);
 	}
 	sb->s_flags |= SB_RDONLY | SB_NOATIME;
 	sb->s_maxbytes = MAX_LFS_FILESIZE;
@@ -557,13 +558,11 @@
 	sb->s_op = &erofs_sops;
 	sb->s_xattr = erofs_xattr_handlers;
 
-	if (test_opt(ctx, POSIX_ACL))
+	if (test_opt(&sbi->opt, POSIX_ACL))
 		sb->s_flags |= SB_POSIXACL;
 	else
 		sb->s_flags &= ~SB_POSIXACL;
 
-	sbi->ctx = *ctx;
-
 #ifdef CONFIG_EROFS_FS_ZIP
 	xa_init(&sbi->managed_pslots);
 #endif
@@ -607,12 +606,12 @@
 
 	DBG_BUGON(!sb_rdonly(sb));
 
-	if (test_opt(ctx, POSIX_ACL))
+	if (test_opt(&ctx->opt, POSIX_ACL))
 		fc->sb_flags |= SB_POSIXACL;
 	else
 		fc->sb_flags &= ~SB_POSIXACL;
 
-	sbi->ctx = *ctx;
+	sbi->opt = ctx->opt;
 
 	fc->sb_flags |= SB_RDONLY;
 	return 0;
@@ -640,7 +639,6 @@
 	erofs_default_options(fc->fs_private);
 
 	fc->ops = &erofs_context_ops;
-
 	return 0;
 }
 
@@ -763,31 +761,31 @@
 static int erofs_show_options(struct seq_file *seq, struct dentry *root)
 {
 	struct erofs_sb_info *sbi = EROFS_SB(root->d_sb);
-	struct erofs_fs_context *ctx = &sbi->ctx;
+	struct erofs_mount_opts *opt = &sbi->opt;
 
 #ifdef CONFIG_EROFS_FS_XATTR
-	if (test_opt(ctx, XATTR_USER))
+	if (test_opt(opt, XATTR_USER))
 		seq_puts(seq, ",user_xattr");
 	else
 		seq_puts(seq, ",nouser_xattr");
 #endif
 #ifdef CONFIG_EROFS_FS_POSIX_ACL
-	if (test_opt(ctx, POSIX_ACL))
+	if (test_opt(opt, POSIX_ACL))
 		seq_puts(seq, ",acl");
 	else
 		seq_puts(seq, ",noacl");
 #endif
 #ifdef CONFIG_EROFS_FS_ZIP
-	if (ctx->cache_strategy == EROFS_ZIP_CACHE_DISABLED)
+	if (opt->cache_strategy == EROFS_ZIP_CACHE_DISABLED)
 		seq_puts(seq, ",cache_strategy=disabled");
-	else if (ctx->cache_strategy == EROFS_ZIP_CACHE_READAHEAD)
+	else if (opt->cache_strategy == EROFS_ZIP_CACHE_READAHEAD)
 		seq_puts(seq, ",cache_strategy=readahead");
-	else if (ctx->cache_strategy == EROFS_ZIP_CACHE_READAROUND)
+	else if (opt->cache_strategy == EROFS_ZIP_CACHE_READAROUND)
 		seq_puts(seq, ",cache_strategy=readaround");
 #endif
-	if (test_opt(ctx, DAX_ALWAYS))
+	if (test_opt(opt, DAX_ALWAYS))
 		seq_puts(seq, ",dax=always");
-	if (test_opt(ctx, DAX_NEVER))
+	if (test_opt(opt, DAX_NEVER))
 		seq_puts(seq, ",dax=never");
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/utils.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/utils.c
@@ -141,7 +141,7 @@
 	 * however in order to avoid some race conditions, add a
 	 * DBG_BUGON to observe this in advance.
 	 */
-	DBG_BUGON(xa_erase(&sbi->managed_pslots, grp->index) != grp);
+	DBG_BUGON(__xa_erase(&sbi->managed_pslots, grp->index) != grp);
 
 	/* last refcount should be connected with its managed pslot.  */
 	erofs_workgroup_unfreeze(grp, 0);
@@ -156,15 +156,19 @@
 	unsigned int freed = 0;
 	unsigned long index;
 
+	xa_lock(&sbi->managed_pslots);
 	xa_for_each(&sbi->managed_pslots, index, grp) {
 		/* try to shrink each valid workgroup */
 		if (!erofs_try_to_release_workgroup(sbi, grp))
 			continue;
+		xa_unlock(&sbi->managed_pslots);
 
 		++freed;
 		if (!--nr_shrink)
-			break;
+			return freed;
+		xa_lock(&sbi->managed_pslots);
 	}
+	xa_unlock(&sbi->managed_pslots);
 	return freed;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/xattr.c
@@ -429,7 +429,7 @@
 
 static bool erofs_xattr_user_list(struct dentry *dentry)
 {
-	return test_opt(&EROFS_SB(dentry->d_sb)->ctx, XATTR_USER);
+	return test_opt(&EROFS_SB(dentry->d_sb)->opt, XATTR_USER);
 }
 
 static bool erofs_xattr_trusted_list(struct dentry *dentry)
@@ -476,7 +476,7 @@
 
 	switch (handler->flags) {
 	case EROFS_XATTR_INDEX_USER:
-		if (!test_opt(&sbi->ctx, XATTR_USER))
+		if (!test_opt(&sbi->opt, XATTR_USER))
 			return -EOPNOTSUPP;
 		break;
 	case EROFS_XATTR_INDEX_TRUSTED:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/zdata.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/zdata.c
@@ -373,8 +373,8 @@
 
 /* callers must be with collection lock held */
 static int z_erofs_attach_page(struct z_erofs_collector *clt,
-			       struct page *page,
-			       enum z_erofs_page_type type)
+			       struct page *page, enum z_erofs_page_type type,
+			       bool pvec_safereuse)
 {
 	int ret;
 
@@ -384,9 +384,9 @@
 	    z_erofs_try_inplace_io(clt, page))
 		return 0;
 
-	ret = z_erofs_pagevec_enqueue(&clt->vector, page, type);
+	ret = z_erofs_pagevec_enqueue(&clt->vector, page, type,
+				      pvec_safereuse);
 	clt->cl->vcnt += (unsigned int)ret;
-
 	return ret ? 0 : -EAGAIN;
 }
 
@@ -695,7 +695,7 @@
 		goto err_out;
 
 	/* preload all compressed pages (maybe downgrade role if necessary) */
-	if (should_alloc_managed_pages(fe, sbi->ctx.cache_strategy, map->m_la))
+	if (should_alloc_managed_pages(fe, sbi->opt.cache_strategy, map->m_la))
 		cache_strategy = TRYALLOC;
 	else
 		cache_strategy = DONTALLOC;
@@ -713,9 +713,11 @@
 	tight &= (clt->mode >= COLLECT_PRIMARY_HOOKED &&
 		  clt->mode != COLLECT_PRIMARY_FOLLOWED_NOINPLACE);
 
-	cur = end - min_t(unsigned int, offset + end - map->m_la, end);
+	cur = end - min_t(erofs_off_t, offset + end - map->m_la, end);
 	if (!(map->m_flags & EROFS_MAP_MAPPED)) {
 		zero_user_segment(page, cur, end);
+		++spiltted;
+		tight = false;
 		goto next_part;
 	}
 
@@ -729,7 +731,8 @@
 		tight &= (clt->mode >= COLLECT_PRIMARY_FOLLOWED);
 
 retry:
-	err = z_erofs_attach_page(clt, page, page_type);
+	err = z_erofs_attach_page(clt, page, page_type,
+				  clt->mode >= COLLECT_PRIMARY_FOLLOWED);
 	/* should allocate an additional short-lived page for pagevec */
 	if (err == -EAGAIN) {
 		struct page *const newpage =
@@ -737,7 +740,7 @@
 
 		set_page_private(newpage, Z_EROFS_SHORTLIVED_PAGE);
 		err = z_erofs_attach_page(clt, newpage,
-					  Z_EROFS_PAGE_TYPE_EXCLUSIVE);
+					  Z_EROFS_PAGE_TYPE_EXCLUSIVE, true);
 		if (!err)
 			goto retry;
 	}
@@ -796,7 +799,7 @@
 	/* Use workqueue and sync decompression for atomic contexts only */
 	if (in_atomic() || irqs_disabled()) {
 		queue_work(z_erofs_workqueue, &io->u.work);
-		sbi->ctx.readahead_sync_decompress = true;
+		sbi->opt.readahead_sync_decompress = true;
 		return;
 	}
 	z_erofs_decompressqueue_work(&io->u.work);
@@ -1411,8 +1414,8 @@
 	struct erofs_sb_info *const sbi = EROFS_I_SB(inode);
 
 	unsigned int nr_pages = readahead_count(rac);
-	bool sync = (sbi->ctx.readahead_sync_decompress &&
-			nr_pages <= sbi->ctx.max_sync_decompress_pages);
+	bool sync = (sbi->opt.readahead_sync_decompress &&
+			nr_pages <= sbi->opt.max_sync_decompress_pages);
 	struct z_erofs_decompress_frontend f = DECOMPRESS_FRONTEND_INIT(inode);
 	struct page *page, *head = NULL;
 	LIST_HEAD(pagepool);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/zmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/zmap.c
@@ -191,6 +191,10 @@
 	case Z_EROFS_VLE_CLUSTER_TYPE_PLAIN:
 	case Z_EROFS_VLE_CLUSTER_TYPE_HEAD:
 		m->clusterofs = le16_to_cpu(di->di_clusterofs);
+		if (m->clusterofs >= 1 << vi->z_logical_clusterbits) {
+			DBG_BUGON(1);
+			return -EFSCORRUPTED;
+		}
 		m->pblk = le32_to_cpu(di->di_u.blkaddr);
 		break;
 	default:
@@ -249,7 +253,7 @@
 	u8 *in, type;
 	bool big_pcluster;
 
-	if (1 << amortizedshift == 4)
+	if (1 << amortizedshift == 4 && lclusterbits <= 14)
 		vcnt = 2;
 	else if (1 << amortizedshift == 2 && lclusterbits == 12)
 		vcnt = 16;
@@ -347,7 +351,6 @@
 {
 	struct inode *const inode = m->inode;
 	struct erofs_inode *const vi = EROFS_I(inode);
-	const unsigned int lclusterbits = vi->z_logical_clusterbits;
 	const erofs_off_t ebase = ALIGN(iloc(EROFS_I_SB(inode), vi->nid) +
 					vi->inode_isize + vi->xattr_isize, 8) +
 		sizeof(struct z_erofs_map_header);
@@ -357,9 +360,6 @@
 	erofs_off_t pos;
 	int err;
 
-	if (lclusterbits != 12)
-		return -EOPNOTSUPP;
-
 	if (lcn >= totalidx)
 		return -EINVAL;
 
@@ -700,12 +700,16 @@
 		iomap->type = IOMAP_HOLE;
 		iomap->addr = IOMAP_NULL_ADDR;
 		/*
-		 * No strict rule how to describe extents for post EOF, yet
-		 * we need do like below. Otherwise, iomap itself will get
+		 * No strict rule on how to describe extents for post EOF, yet
+		 * we need to do like below. Otherwise, iomap itself will get
 		 * into an endless loop on post EOF.
+		 *
+		 * Calculate the effective offset by subtracting extent start
+		 * (map.m_la) from the requested offset, and add it to length.
+		 * (NB: offset >= map.m_la always)
 		 */
 		if (iomap->offset >= inode->i_size)
-			iomap->length = length + map.m_la - offset;
+			iomap->length = length + offset - map.m_la;
 	}
 	iomap->flags = 0;
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/erofs/zpvec.h
+++ linux-xilinx-zynqmp-5.15.0/fs/erofs/zpvec.h
@@ -106,11 +106,18 @@
 
 static inline bool z_erofs_pagevec_enqueue(struct z_erofs_pagevec_ctor *ctor,
 					   struct page *page,
-					   enum z_erofs_page_type type)
+					   enum z_erofs_page_type type,
+					   bool pvec_safereuse)
 {
-	if (!ctor->next && type)
-		if (ctor->index + 1 == ctor->nr)
+	if (!ctor->next) {
+		/* some pages cannot be reused as pvec safely without I/O */
+		if (type == Z_EROFS_PAGE_TYPE_EXCLUSIVE && !pvec_safereuse)
+			type = Z_EROFS_VLE_PAGE_TYPE_TAIL_SHARED;
+
+		if (type != Z_EROFS_PAGE_TYPE_EXCLUSIVE &&
+		    ctor->index + 1 == ctor->nr)
 			return false;
+	}
 
 	if (ctor->index >= ctor->nr)
 		z_erofs_pagevec_ctor_pagedown(ctor, false);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/eventfd.c
+++ linux-xilinx-zynqmp-5.15.0/fs/eventfd.c
@@ -43,21 +43,7 @@
 	int id;
 };
 
-/**
- * eventfd_signal - Adds @n to the eventfd counter.
- * @ctx: [in] Pointer to the eventfd context.
- * @n: [in] Value of the counter to be added to the eventfd internal counter.
- *          The value cannot be negative.
- *
- * This function is supposed to be called by the kernel in paths that do not
- * allow sleeping. In this function we allow the counter to reach the ULLONG_MAX
- * value, and we signal this as overflow condition by returning a EPOLLERR
- * to poll(2).
- *
- * Returns the amount by which the counter was incremented.  This will be less
- * than @n if the counter has overflowed.
- */
-__u64 eventfd_signal(struct eventfd_ctx *ctx, __u64 n)
+__u64 eventfd_signal_mask(struct eventfd_ctx *ctx, __u64 n, unsigned mask)
 {
 	unsigned long flags;
 
@@ -69,21 +55,40 @@
 	 * it returns false, the eventfd_signal() call should be deferred to a
 	 * safe context.
 	 */
-	if (WARN_ON_ONCE(current->in_eventfd_signal))
+	if (WARN_ON_ONCE(current->in_eventfd))
 		return 0;
 
 	spin_lock_irqsave(&ctx->wqh.lock, flags);
-	current->in_eventfd_signal = 1;
+	current->in_eventfd = 1;
 	if (ULLONG_MAX - ctx->count < n)
 		n = ULLONG_MAX - ctx->count;
 	ctx->count += n;
 	if (waitqueue_active(&ctx->wqh))
-		wake_up_locked_poll(&ctx->wqh, EPOLLIN);
-	current->in_eventfd_signal = 0;
+		wake_up_locked_poll(&ctx->wqh, EPOLLIN | mask);
+	current->in_eventfd = 0;
 	spin_unlock_irqrestore(&ctx->wqh.lock, flags);
 
 	return n;
 }
+
+/**
+ * eventfd_signal - Adds @n to the eventfd counter.
+ * @ctx: [in] Pointer to the eventfd context.
+ * @n: [in] Value of the counter to be added to the eventfd internal counter.
+ *          The value cannot be negative.
+ *
+ * This function is supposed to be called by the kernel in paths that do not
+ * allow sleeping. In this function we allow the counter to reach the ULLONG_MAX
+ * value, and we signal this as overflow condition by returning a EPOLLERR
+ * to poll(2).
+ *
+ * Returns the amount by which the counter was incremented.  This will be less
+ * than @n if the counter has overflowed.
+ */
+__u64 eventfd_signal(struct eventfd_ctx *ctx, __u64 n)
+{
+	return eventfd_signal_mask(ctx, n, 0);
+}
 EXPORT_SYMBOL_GPL(eventfd_signal);
 
 static void eventfd_free_ctx(struct eventfd_ctx *ctx)
@@ -184,7 +189,7 @@
 {
 	lockdep_assert_held(&ctx->wqh.lock);
 
-	*cnt = (ctx->flags & EFD_SEMAPHORE) ? 1 : ctx->count;
+	*cnt = ((ctx->flags & EFD_SEMAPHORE) && ctx->count) ? 1 : ctx->count;
 	ctx->count -= *cnt;
 }
 EXPORT_SYMBOL_GPL(eventfd_ctx_do_read);
@@ -253,8 +258,10 @@
 		__set_current_state(TASK_RUNNING);
 	}
 	eventfd_ctx_do_read(ctx, &ucnt);
+	current->in_eventfd = 1;
 	if (waitqueue_active(&ctx->wqh))
 		wake_up_locked_poll(&ctx->wqh, EPOLLOUT);
+	current->in_eventfd = 0;
 	spin_unlock_irq(&ctx->wqh.lock);
 	if (unlikely(copy_to_iter(&ucnt, sizeof(ucnt), to) != sizeof(ucnt)))
 		return -EFAULT;
@@ -301,8 +308,10 @@
 	}
 	if (likely(res > 0)) {
 		ctx->count += ucnt;
+		current->in_eventfd = 1;
 		if (waitqueue_active(&ctx->wqh))
 			wake_up_locked_poll(&ctx->wqh, EPOLLIN);
+		current->in_eventfd = 0;
 	}
 	spin_unlock_irq(&ctx->wqh.lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/eventpoll.c
+++ linux-xilinx-zynqmp-5.15.0/fs/eventpoll.c
@@ -484,7 +484,8 @@
  */
 #ifdef CONFIG_DEBUG_LOCK_ALLOC
 
-static void ep_poll_safewake(struct eventpoll *ep, struct epitem *epi)
+static void ep_poll_safewake(struct eventpoll *ep, struct epitem *epi,
+			     unsigned pollflags)
 {
 	struct eventpoll *ep_src;
 	unsigned long flags;
@@ -515,16 +516,17 @@
 	}
 	spin_lock_irqsave_nested(&ep->poll_wait.lock, flags, nests);
 	ep->nests = nests + 1;
-	wake_up_locked_poll(&ep->poll_wait, EPOLLIN);
+	wake_up_locked_poll(&ep->poll_wait, EPOLLIN | pollflags);
 	ep->nests = 0;
 	spin_unlock_irqrestore(&ep->poll_wait.lock, flags);
 }
 
 #else
 
-static void ep_poll_safewake(struct eventpoll *ep, struct epitem *epi)
+static void ep_poll_safewake(struct eventpoll *ep, struct epitem *epi,
+			     unsigned pollflags)
 {
-	wake_up_poll(&ep->poll_wait, EPOLLIN);
+	wake_up_poll(&ep->poll_wait, EPOLLIN | pollflags);
 }
 
 #endif
@@ -694,7 +696,8 @@
 	to_free = NULL;
 	head = file->f_ep;
 	if (head->first == &epi->fllink && !epi->fllink.next) {
-		file->f_ep = NULL;
+		/* See eventpoll_release() for details. */
+		WRITE_ONCE(file->f_ep, NULL);
 		if (!is_file_epoll(file)) {
 			struct epitems_head *v;
 			v = container_of(head, struct epitems_head, epitems);
@@ -735,7 +738,7 @@
 
 	/* We need to release all tasks waiting for these file */
 	if (waitqueue_active(&ep->poll_wait))
-		ep_poll_safewake(ep, NULL);
+		ep_poll_safewake(ep, NULL, 0);
 
 	/*
 	 * We need to lock this because we could be hit by
@@ -831,6 +834,34 @@
 }
 
 /*
+ * The ffd.file pointer may be in the process of being torn down due to
+ * being closed, but we may not have finished eventpoll_release() yet.
+ *
+ * Normally, even with the atomic_long_inc_not_zero, the file may have
+ * been free'd and then gotten re-allocated to something else (since
+ * files are not RCU-delayed, they are SLAB_TYPESAFE_BY_RCU).
+ *
+ * But for epoll, users hold the ep->mtx mutex, and as such any file in
+ * the process of being free'd will block in eventpoll_release_file()
+ * and thus the underlying file allocation will not be free'd, and the
+ * file re-use cannot happen.
+ *
+ * For the same reason we can avoid a rcu_read_lock() around the
+ * operation - 'ffd.file' cannot go away even if the refcount has
+ * reached zero (but we must still not call out to ->poll() functions
+ * etc).
+ */
+static struct file *epi_fget(const struct epitem *epi)
+{
+	struct file *file;
+
+	file = epi->ffd.file;
+	if (!atomic_long_inc_not_zero(&file->f_count))
+		file = NULL;
+	return file;
+}
+
+/*
  * Differs from ep_eventpoll_poll() in that internal callers already have
  * the ep->mtx so we need to start from depth=1, such that mutex_lock_nested()
  * is correctly annotated.
@@ -838,14 +869,22 @@
 static __poll_t ep_item_poll(const struct epitem *epi, poll_table *pt,
 				 int depth)
 {
-	struct file *file = epi->ffd.file;
+	struct file *file = epi_fget(epi);
 	__poll_t res;
 
+	/*
+	 * We could return EPOLLERR | EPOLLHUP or something, but let's
+	 * treat this more as "file doesn't exist, poll didn't happen".
+	 */
+	if (!file)
+		return 0;
+
 	pt->_key = epi->event.events;
 	if (!is_file_epoll(file))
 		res = vfs_poll(file, pt);
 	else
 		res = __ep_eventpoll_poll(file, pt, depth);
+	fput(file);
 	return res & epi->event.events;
 }
 
@@ -1191,7 +1230,10 @@
 				break;
 			}
 		}
-		wake_up(&ep->wq);
+		if (sync)
+			wake_up_sync(&ep->wq);
+		else
+			wake_up(&ep->wq);
 	}
 	if (waitqueue_active(&ep->poll_wait))
 		pwake++;
@@ -1201,7 +1243,7 @@
 
 	/* We have to call this outside the lock */
 	if (pwake)
-		ep_poll_safewake(ep, epi);
+		ep_poll_safewake(ep, epi, pollflags & EPOLL_URING_WAKE);
 
 	if (!(epi->event.events & EPOLLEXCLUSIVE))
 		ewake = 1;
@@ -1422,7 +1464,8 @@
 			spin_unlock(&file->f_lock);
 			goto allocate;
 		}
-		file->f_ep = head;
+		/* See eventpoll_release() for details. */
+		WRITE_ONCE(file->f_ep, head);
 		to_free = NULL;
 	}
 	hlist_add_head_rcu(&epi->fllink, file->f_ep);
@@ -1546,7 +1589,7 @@
 
 	/* We have to call this outside the lock */
 	if (pwake)
-		ep_poll_safewake(ep, NULL);
+		ep_poll_safewake(ep, NULL, 0);
 
 	return 0;
 }
@@ -1622,7 +1665,7 @@
 
 	/* We have to call this outside the lock */
 	if (pwake)
-		ep_poll_safewake(ep, NULL);
+		ep_poll_safewake(ep, NULL, 0);
 
 	return 0;
 }
@@ -1740,6 +1783,25 @@
 	return to;
 }
 
+/*
+ * autoremove_wake_function, but remove even on failure to wake up, because we
+ * know that default_wake_function/ttwu will only fail if the thread is already
+ * woken, and in that case the ep_poll loop will remove the entry anyways, not
+ * try to reuse it.
+ */
+static int ep_autoremove_wake_function(struct wait_queue_entry *wq_entry,
+				       unsigned int mode, int sync, void *key)
+{
+	int ret = default_wake_function(wq_entry, mode, sync, key);
+
+	/*
+	 * Pairs with list_empty_careful in ep_poll, and ensures future loop
+	 * iterations see the cause of this wakeup.
+	 */
+	list_del_init_careful(&wq_entry->entry);
+	return ret;
+}
+
 /**
  * ep_poll - Retrieves ready events, and delivers them to the caller-supplied
  *           event buffer.
@@ -1821,8 +1883,15 @@
 		 * normal wakeup path no need to call __remove_wait_queue()
 		 * explicitly, thus ep->lock is not taken, which halts the
 		 * event delivery.
+		 *
+		 * In fact, we now use an even more aggressive function that
+		 * unconditionally removes, because we don't reuse the wait
+		 * entry between loop iterations. This lets us also avoid the
+		 * performance issue if a process is killed, causing all of its
+		 * threads to wake up without being removed normally.
 		 */
 		init_wait(&wait);
+		wait.func = ep_autoremove_wake_function;
 
 		write_lock_irq(&ep->lock);
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exec.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exec.c
@@ -111,6 +111,7 @@
 	return (path->mnt->mnt_flags & MNT_NOEXEC) ||
 	       (path->mnt->mnt_sb->s_iflags & SB_I_NOEXEC);
 }
+EXPORT_SYMBOL_GPL(path_noexec);
 
 #ifdef CONFIG_USELIB
 /*
@@ -142,13 +143,11 @@
 		goto out;
 
 	/*
-	 * may_open() has already checked for this, so it should be
-	 * impossible to trip now. But we need to be extra cautious
-	 * and check again at the very end too.
+	 * Check do_open_execat() for an explanation.
 	 */
 	error = -EACCES;
-	if (WARN_ON_ONCE(!S_ISREG(file_inode(file)->i_mode) ||
-			 path_noexec(&file->f_path)))
+	if (WARN_ON_ONCE(!S_ISREG(file_inode(file)->i_mode)) ||
+	    path_noexec(&file->f_path))
 		goto exit;
 
 	fsnotify_open(file);
@@ -494,8 +493,14 @@
 	 * the stack. They aren't stored until much later when we can't
 	 * signal to the parent that the child has run out of stack space.
 	 * Instead, calculate it here so it's possible to fail gracefully.
+	 *
+	 * In the case of argc = 0, make sure there is space for adding a
+	 * empty string (which will bump argc to 1), to ensure confused
+	 * userspace programs don't start processing from argv[1], thinking
+	 * argc can never be 0, to keep them from walking envp by accident.
+	 * See do_execveat_common().
 	 */
-	ptr_size = (bprm->argc + bprm->envc) * sizeof(void *);
+	ptr_size = (max(bprm->argc, 1) + bprm->envc) * sizeof(void *);
 	if (limit <= ptr_size)
 		return -E2BIG;
 	limit -= ptr_size;
@@ -760,7 +765,8 @@
 	stack_base = calc_max_stack_size(stack_base);
 
 	/* Add space for stack randomization. */
-	stack_base += (STACK_RND_MASK << PAGE_SHIFT);
+	if (current->flags & PF_RANDOMIZE)
+		stack_base += (STACK_RND_MASK << PAGE_SHIFT);
 
 	/* Make sure we didn't let the argument array grow too large. */
 	if (vma->vm_end - vma->vm_start > stack_base)
@@ -882,6 +888,7 @@
 			goto out;
 	}
 
+	bprm->exec += *sp_location - MAX_ARG_PAGES * PAGE_SIZE;
 	*sp_location = sp;
 
 out:
@@ -911,16 +918,16 @@
 
 	file = do_filp_open(fd, name, &open_exec_flags);
 	if (IS_ERR(file))
-		goto out;
+		return file;
 
 	/*
-	 * may_open() has already checked for this, so it should be
-	 * impossible to trip now. But we need to be extra cautious
-	 * and check again at the very end too.
+	 * In the past the regular type check was here. It moved to may_open() in
+	 * 633fb6ac3980 ("exec: move S_ISREG() check earlier"). Since then it is
+	 * an invariant that all non-regular files error out before we get here.
 	 */
 	err = -EACCES;
-	if (WARN_ON_ONCE(!S_ISREG(file_inode(file)->i_mode) ||
-			 path_noexec(&file->f_path)))
+	if (WARN_ON_ONCE(!S_ISREG(file_inode(file)->i_mode)) ||
+	    path_noexec(&file->f_path))
 		goto exit;
 
 	err = deny_write_access(file);
@@ -930,7 +937,6 @@
 	if (name->name[0] != '\0')
 		fsnotify_open(file);
 
-out:
 	return file;
 
 exit:
@@ -1192,11 +1198,11 @@
 			return -ENOMEM;
 
 		refcount_set(&newsighand->count, 1);
-		memcpy(newsighand->action, oldsighand->action,
-		       sizeof(newsighand->action));
 
 		write_lock_irq(&tasklist_lock);
 		spin_lock(&oldsighand->siglock);
+		memcpy(newsighand->action, oldsighand->action,
+		       sizeof(newsighand->action));
 		rcu_assign_pointer(me->sighand, newsighand);
 		spin_unlock(&oldsighand->siglock);
 		write_unlock_irq(&tasklist_lock);
@@ -1292,7 +1298,10 @@
 	bprm->mm = NULL;
 
 #ifdef CONFIG_POSIX_TIMERS
-	exit_itimers(me->signal);
+	spin_lock_irq(&me->sighand->siglock);
+	posix_cpu_timers_exit(me);
+	spin_unlock_irq(&me->sighand->siglock);
+	exit_itimers(me);
 	flush_itimer_signals();
 #endif
 
@@ -1401,6 +1410,9 @@
 
 out_unlock:
 	up_write(&me->signal->exec_update_lock);
+	if (!bprm->cred)
+		mutex_unlock(&me->signal->cred_guard_mutex);
+
 out:
 	return retval;
 }
@@ -1590,6 +1602,7 @@
 	unsigned int mode;
 	kuid_t uid;
 	kgid_t gid;
+	int err;
 
 	if (!mnt_may_suid(file->f_path.mnt))
 		return;
@@ -1607,12 +1620,17 @@
 	/* Be careful if suid/sgid is set */
 	inode_lock(inode);
 
-	/* reload atomically mode/uid/gid now that lock held */
+	/* Atomically reload and check mode/uid/gid now that lock held. */
 	mode = inode->i_mode;
 	uid = i_uid_into_mnt(mnt_userns, inode);
 	gid = i_gid_into_mnt(mnt_userns, inode);
+	err = inode_permission(mnt_userns, inode, MAY_EXEC);
 	inode_unlock(inode);
 
+	/* Did the exec bit vanish out from under us? Give up. */
+	if (err)
+		return;
+
 	/* We ignore suid/sgid if there are no mappings for them in the ns */
 	if (!kuid_has_mapping(bprm->cred->user_ns, uid) ||
 		 !kgid_has_mapping(bprm->cred->user_ns, gid))
@@ -1852,7 +1870,7 @@
 	 * SIGSEGV.
 	 */
 	if (bprm->point_of_no_return && !fatal_signal_pending(current))
-		force_sigsegv(SIGSEGV);
+		force_fatal_sig(SIGSEGV);
 
 out_unmark:
 	current->fs->in_exec = 0;
@@ -1895,6 +1913,9 @@
 	}
 
 	retval = count(argv, MAX_ARG_STRINGS);
+	if (retval == 0)
+		pr_warn_once("process '%s' launched '%s' with NULL argv: empty string added\n",
+			     current->comm, bprm->filename);
 	if (retval < 0)
 		goto out_free;
 	bprm->argc = retval;
@@ -1921,6 +1942,19 @@
 	if (retval < 0)
 		goto out_free;
 
+	/*
+	 * When argv is empty, add an empty string ("") as argv[0] to
+	 * ensure confused userspace programs that start processing
+	 * from argv[1] won't end up walking envp. See also
+	 * bprm_stack_limits().
+	 */
+	if (bprm->argc == 0) {
+		retval = copy_string_kernel("", bprm);
+		if (retval < 0)
+			goto out_free;
+		bprm->argc = 1;
+	}
+
 	retval = bprm_execve(bprm, fd, filename, flags);
 out_free:
 	free_bprm(bprm);
@@ -1949,6 +1983,8 @@
 	}
 
 	retval = count_strings_kernel(argv);
+	if (WARN_ON_ONCE(retval == 0))
+		retval = -EINVAL;
 	if (retval < 0)
 		goto out_free;
 	bprm->argc = retval;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/balloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/balloc.c
@@ -69,7 +69,7 @@
 	}
 	sbi->map_sectors = ((need_map_size - 1) >>
 			(sb->s_blocksize_bits)) + 1;
-	sbi->vol_amap = kmalloc_array(sbi->map_sectors,
+	sbi->vol_amap = kvmalloc_array(sbi->map_sectors,
 				sizeof(struct buffer_head *), GFP_KERNEL);
 	if (!sbi->vol_amap)
 		return -ENOMEM;
@@ -84,7 +84,7 @@
 			while (j < i)
 				brelse(sbi->vol_amap[j++]);
 
-			kfree(sbi->vol_amap);
+			kvfree(sbi->vol_amap);
 			sbi->vol_amap = NULL;
 			return -EIO;
 		}
@@ -110,11 +110,8 @@
 				return -EIO;
 
 			type = exfat_get_entry_type(ep);
-			if (type == TYPE_UNUSED)
-				break;
-			if (type != TYPE_BITMAP)
-				continue;
-			if (ep->dentry.bitmap.flags == 0x0) {
+			if (type == TYPE_BITMAP &&
+			    ep->dentry.bitmap.flags == 0x0) {
 				int err;
 
 				err = exfat_allocate_bitmap(sb, ep);
@@ -122,6 +119,9 @@
 				return err;
 			}
 			brelse(bh);
+
+			if (type == TYPE_UNUSED)
+				return -EINVAL;
 		}
 
 		if (exfat_get_next_cluster(sb, &clu.dir))
@@ -138,7 +138,7 @@
 	for (i = 0; i < sbi->map_sectors; i++)
 		__brelse(sbi->vol_amap[i]);
 
-	kfree(sbi->vol_amap);
+	kvfree(sbi->vol_amap);
 }
 
 int exfat_set_bitmap(struct inode *inode, unsigned int clu, bool sync)
@@ -148,7 +148,9 @@
 	struct super_block *sb = inode->i_sb;
 	struct exfat_sb_info *sbi = EXFAT_SB(sb);
 
-	WARN_ON(clu < EXFAT_FIRST_CLUSTER);
+	if (!is_valid_cluster(sbi, clu))
+		return -EINVAL;
+
 	ent_idx = CLUSTER_TO_BITMAP_ENT(clu);
 	i = BITMAP_OFFSET_SECTOR_INDEX(sb, ent_idx);
 	b = BITMAP_OFFSET_BIT_IN_SECTOR(sb, ent_idx);
@@ -158,7 +160,7 @@
 	return 0;
 }
 
-void exfat_clear_bitmap(struct inode *inode, unsigned int clu, bool sync)
+int exfat_clear_bitmap(struct inode *inode, unsigned int clu, bool sync)
 {
 	int i, b;
 	unsigned int ent_idx;
@@ -166,12 +168,18 @@
 	struct exfat_sb_info *sbi = EXFAT_SB(sb);
 	struct exfat_mount_options *opts = &sbi->options;
 
-	WARN_ON(clu < EXFAT_FIRST_CLUSTER);
+	if (!is_valid_cluster(sbi, clu))
+		return -EIO;
+
 	ent_idx = CLUSTER_TO_BITMAP_ENT(clu);
 	i = BITMAP_OFFSET_SECTOR_INDEX(sb, ent_idx);
 	b = BITMAP_OFFSET_BIT_IN_SECTOR(sb, ent_idx);
 
+	if (!test_bit_le(b, sbi->vol_amap[i]->b_data))
+		return -EIO;
+
 	clear_bit_le(b, sbi->vol_amap[i]->b_data);
+
 	exfat_update_bh(sbi->vol_amap[i], sync);
 
 	if (opts->discard) {
@@ -186,6 +194,8 @@
 			opts->discard = 0;
 		}
 	}
+
+	return 0;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/dir.c
@@ -34,6 +34,7 @@
 {
 	int i;
 	struct exfat_entry_set_cache *es;
+	unsigned int uni_len = 0, len;
 
 	es = exfat_get_dentry_set(sb, p_dir, entry, ES_ALL_ENTRIES);
 	if (!es)
@@ -52,7 +53,10 @@
 		if (exfat_get_entry_type(ep) != TYPE_EXTEND)
 			break;
 
-		exfat_extract_uni_name(ep, uniname);
+		len = exfat_extract_uni_name(ep, uniname);
+		uni_len += len;
+		if (len != EXFAT_FILE_NAME_LEN || uni_len >= MAX_NAME_LENGTH)
+			break;
 		uniname += EXFAT_FILE_NAME_LEN;
 	}
 
@@ -103,7 +107,7 @@
 			clu.dir = ei->hint_bmap.clu;
 		}
 
-		while (clu_offset > 0) {
+		while (clu_offset > 0 && clu.dir != EXFAT_EOF_CLUSTER) {
 			if (exfat_get_next_cluster(sb, &(clu.dir)))
 				return -EIO;
 
@@ -122,7 +126,7 @@
 			type = exfat_get_entry_type(ep);
 			if (type == TYPE_UNUSED) {
 				brelse(bh);
-				break;
+				goto out;
 			}
 
 			if (type != TYPE_FILE && type != TYPE_DIR) {
@@ -182,6 +186,7 @@
 		}
 	}
 
+out:
 	dir_entry->namebuf.lfn[0] = '\0';
 	*cpos = EXFAT_DEN_TO_B(dentry);
 	return 0;
@@ -211,7 +216,10 @@
 	exfat_init_namebuf(nb);
 }
 
-/* skip iterating emit_dots when dir is empty */
+/*
+ * Before calling dir_emit*(), sbi->s_lock should be released
+ * because page fault can occur in dir_emit*().
+ */
 #define ITER_POS_FILLED_DOTS    (2)
 static int exfat_iterate(struct file *filp, struct dir_context *ctx)
 {
@@ -226,35 +234,33 @@
 	int err = 0, fake_offset = 0;
 
 	exfat_init_namebuf(nb);
-	mutex_lock(&EXFAT_SB(sb)->s_lock);
 
 	cpos = ctx->pos;
 	if (!dir_emit_dots(filp, ctx))
-		goto unlock;
+		goto out;
 
 	if (ctx->pos == ITER_POS_FILLED_DOTS) {
 		cpos = 0;
 		fake_offset = 1;
 	}
 
-	if (cpos & (DENTRY_SIZE - 1)) {
-		err = -ENOENT;
-		goto unlock;
-	}
+	cpos = round_up(cpos, DENTRY_SIZE);
 
 	/* name buffer should be allocated before use */
 	err = exfat_alloc_namebuf(nb);
 	if (err)
-		goto unlock;
+		goto out;
 get_new:
+	mutex_lock(&EXFAT_SB(sb)->s_lock);
+
 	if (ei->flags == ALLOC_NO_FAT_CHAIN && cpos >= i_size_read(inode))
 		goto end_of_dir;
 
 	err = exfat_readdir(inode, &cpos, &de);
 	if (err) {
 		/*
-		 * At least we tried to read a sector.  Move cpos to next sector
-		 * position (should be aligned).
+		 * At least we tried to read a sector.
+		 * Move cpos to next sector position (should be aligned).
 		 */
 		if (err == -EIO) {
 			cpos += 1 << (sb->s_blocksize_bits);
@@ -277,16 +283,10 @@
 		inum = iunique(sb, EXFAT_ROOT_INO);
 	}
 
-	/*
-	 * Before calling dir_emit(), sb_lock should be released.
-	 * Because page fault can occur in dir_emit() when the size
-	 * of buffer given from user is larger than one page size.
-	 */
 	mutex_unlock(&EXFAT_SB(sb)->s_lock);
 	if (!dir_emit(ctx, nb->lfn, strlen(nb->lfn), inum,
 			(de.attr & ATTR_SUBDIR) ? DT_DIR : DT_REG))
-		goto out_unlocked;
-	mutex_lock(&EXFAT_SB(sb)->s_lock);
+		goto out;
 	ctx->pos = cpos;
 	goto get_new;
 
@@ -294,9 +294,8 @@
 	if (!cpos && fake_offset)
 		cpos = ITER_POS_FILLED_DOTS;
 	ctx->pos = cpos;
-unlock:
 	mutex_unlock(&EXFAT_SB(sb)->s_lock);
-out_unlocked:
+out:
 	/*
 	 * To improve performance, free namebuf after unlock sb_lock.
 	 * If namebuf is not allocated, this function do nothing
@@ -620,6 +619,10 @@
 			bforget(es->bh[i]);
 		else
 			brelse(es->bh[i]);
+
+	if (IS_DYNAMIC_ES(es))
+		kfree(es->bh);
+
 	kfree(es);
 	return err;
 }
@@ -855,6 +858,7 @@
 	/* byte offset in sector */
 	off = EXFAT_BLK_OFFSET(byte_offset, sb);
 	es->start_off = off;
+	es->bh = es->__bh;
 
 	/* sector offset in cluster */
 	sec = EXFAT_B_TO_BLK(byte_offset, sb);
@@ -874,6 +878,16 @@
 	es->num_entries = num_entries;
 
 	num_bh = EXFAT_B_TO_BLK_ROUND_UP(off + num_entries * DENTRY_SIZE, sb);
+	if (num_bh > ARRAY_SIZE(es->__bh)) {
+		es->bh = kmalloc_array(num_bh, sizeof(*es->bh), GFP_NOFS);
+		if (!es->bh) {
+			brelse(bh);
+			kfree(es);
+			return NULL;
+		}
+		es->bh[0] = bh;
+	}
+
 	for (i = 1; i < num_bh; i++) {
 		/* get the next sector */
 		if (exfat_is_last_sector_in_cluster(sbi, sec)) {
@@ -1038,7 +1052,8 @@
 			if (entry_type == TYPE_EXTEND) {
 				unsigned short entry_uniname[16], unichar;
 
-				if (step != DIRENT_STEP_NAME) {
+				if (step != DIRENT_STEP_NAME ||
+				    name_len >= MAX_NAME_LENGTH) {
 					step = DIRENT_STEP_FILE;
 					continue;
 				}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/exfat_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/exfat_fs.h
@@ -42,7 +42,7 @@
 #define ES_2_ENTRIES		2
 #define ES_ALL_ENTRIES		0
 
-#define DIR_DELETED		0xFFFF0321
+#define DIR_DELETED		0xFFFFFFF7
 
 /* type values */
 #define TYPE_UNUSED		0x0000
@@ -170,10 +170,13 @@
 	bool modified;
 	unsigned int start_off;
 	int num_bh;
-	struct buffer_head *bh[DIR_CACHE_SIZE];
+	struct buffer_head *__bh[DIR_CACHE_SIZE];
+	struct buffer_head **bh;
 	unsigned int num_entries;
 };
 
+#define IS_DYNAMIC_ES(es)	((es)->__bh != (es)->bh)
+
 struct exfat_dir_entry {
 	struct exfat_chain dir;
 	int entry;
@@ -381,6 +384,14 @@
 		EXFAT_RESERVED_CLUSTERS;
 }
 
+static inline bool is_valid_cluster(struct exfat_sb_info *sbi,
+		unsigned int clus)
+{
+	if (clus < EXFAT_FIRST_CLUSTER || sbi->num_clusters <= clus)
+		return false;
+	return true;
+}
+
 /* super.c */
 int exfat_set_volume_dirty(struct super_block *sb);
 int exfat_clear_volume_dirty(struct super_block *sb);
@@ -409,7 +420,7 @@
 int exfat_load_bitmap(struct super_block *sb);
 void exfat_free_bitmap(struct exfat_sb_info *sbi);
 int exfat_set_bitmap(struct inode *inode, unsigned int clu, bool sync);
-void exfat_clear_bitmap(struct inode *inode, unsigned int clu, bool sync);
+int exfat_clear_bitmap(struct inode *inode, unsigned int clu, bool sync);
 unsigned int exfat_find_free_bitmap(struct super_block *sb, unsigned int clu);
 int exfat_count_used_clusters(struct super_block *sb, unsigned int *ret_count);
 int exfat_trim_fs(struct inode *inode, struct fstrim_range *range);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/fatent.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/fatent.c
@@ -81,14 +81,6 @@
 	return 0;
 }
 
-static inline bool is_valid_cluster(struct exfat_sb_info *sbi,
-		unsigned int clus)
-{
-	if (clus < EXFAT_FIRST_CLUSTER || sbi->num_clusters <= clus)
-		return false;
-	return true;
-}
-
 int exfat_ent_get(struct super_block *sb, unsigned int loc,
 		unsigned int *content)
 {
@@ -182,6 +174,7 @@
 		BITMAP_OFFSET_SECTOR_INDEX(sb, CLUSTER_TO_BITMAP_ENT(clu));
 
 	if (p_chain->flags == ALLOC_NO_FAT_CHAIN) {
+		int err;
 		unsigned int last_cluster = p_chain->dir + p_chain->size - 1;
 		do {
 			bool sync = false;
@@ -196,7 +189,9 @@
 				cur_cmap_i = next_cmap_i;
 			}
 
-			exfat_clear_bitmap(inode, clu, (sync && IS_DIRSYNC(inode)));
+			err = exfat_clear_bitmap(inode, clu, (sync && IS_DIRSYNC(inode)));
+			if (err)
+				break;
 			clu++;
 			num_clusters++;
 		} while (num_clusters < p_chain->size);
@@ -217,16 +212,26 @@
 				cur_cmap_i = next_cmap_i;
 			}
 
-			exfat_clear_bitmap(inode, clu, (sync && IS_DIRSYNC(inode)));
+			if (exfat_clear_bitmap(inode, clu, (sync && IS_DIRSYNC(inode))))
+				break;
 			clu = n_clu;
 			num_clusters++;
 
 			if (err)
-				goto dec_used_clus;
+				break;
+
+			if (num_clusters >= sbi->num_clusters - EXFAT_FIRST_CLUSTER) {
+				/*
+				 * The cluster chain includes a loop, scan the
+				 * bitmap to get the number of used clusters.
+				 */
+				exfat_count_used_clusters(sb, &sbi->used_clusters);
+
+				return 0;
+			}
 		} while (clu != EXFAT_EOF_CLUSTER);
 	}
 
-dec_used_clus:
 	sbi->used_clusters -= num_clusters;
 	return 0;
 }
@@ -259,7 +264,7 @@
 		clu = next;
 		if (exfat_ent_get(sb, clu, &next))
 			return -EIO;
-	} while (next != EXFAT_EOF_CLUSTER);
+	} while (next != EXFAT_EOF_CLUSTER && count <= p_chain->size);
 
 	if (p_chain->size != count) {
 		exfat_fs_error(sb,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/file.c
@@ -110,8 +110,7 @@
 	exfat_set_volume_dirty(sb);
 
 	num_clusters_new = EXFAT_B_TO_CLU_ROUND_UP(i_size_read(inode), sbi);
-	num_clusters_phys =
-		EXFAT_B_TO_CLU_ROUND_UP(EXFAT_I(inode)->i_size_ondisk, sbi);
+	num_clusters_phys = EXFAT_B_TO_CLU_ROUND_UP(ei->i_size_ondisk, sbi);
 
 	exfat_chain_set(&clu, ei->start_clu, num_clusters_phys, ei->flags);
 
@@ -228,12 +227,13 @@
 {
 	struct super_block *sb = inode->i_sb;
 	struct exfat_sb_info *sbi = EXFAT_SB(sb);
+	struct exfat_inode_info *ei = EXFAT_I(inode);
 	unsigned int blocksize = i_blocksize(inode);
 	loff_t aligned_size;
 	int err;
 
 	mutex_lock(&sbi->s_lock);
-	if (EXFAT_I(inode)->start_clu == 0) {
+	if (ei->start_clu == 0) {
 		/*
 		 * Empty start_clu != ~0 (not allocated)
 		 */
@@ -251,8 +251,7 @@
 	else
 		mark_inode_dirty(inode);
 
-	inode->i_blocks = ((i_size_read(inode) + (sbi->cluster_size - 1)) &
-			~(sbi->cluster_size - 1)) >> inode->i_blkbits;
+	inode->i_blocks = round_up(i_size_read(inode), sbi->cluster_size) >> 9;
 write_size:
 	aligned_size = i_size_read(inode);
 	if (aligned_size & (blocksize - 1)) {
@@ -260,11 +259,11 @@
 		aligned_size++;
 	}
 
-	if (EXFAT_I(inode)->i_size_ondisk > i_size_read(inode))
-		EXFAT_I(inode)->i_size_ondisk = aligned_size;
+	if (ei->i_size_ondisk > i_size_read(inode))
+		ei->i_size_ondisk = aligned_size;
 
-	if (EXFAT_I(inode)->i_size_aligned > i_size_read(inode))
-		EXFAT_I(inode)->i_size_aligned = aligned_size;
+	if (ei->i_size_aligned > i_size_read(inode))
+		ei->i_size_aligned = aligned_size;
 	mutex_unlock(&sbi->s_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/inode.c
@@ -114,10 +114,9 @@
 	unsigned int local_clu_offset = clu_offset;
 	unsigned int num_to_be_allocated = 0, num_clusters = 0;
 
-	if (EXFAT_I(inode)->i_size_ondisk > 0)
+	if (ei->i_size_ondisk > 0)
 		num_clusters =
-			EXFAT_B_TO_CLU_ROUND_UP(EXFAT_I(inode)->i_size_ondisk,
-			sbi);
+			EXFAT_B_TO_CLU_ROUND_UP(ei->i_size_ondisk, sbi);
 
 	if (clu_offset >= num_clusters)
 		num_to_be_allocated = clu_offset - num_clusters + 1;
@@ -244,8 +243,7 @@
 				return err;
 		} /* end of if != DIR_DELETED */
 
-		inode->i_blocks +=
-			num_to_be_allocated << sbi->sect_per_clus_bits;
+		inode->i_blocks += EXFAT_CLU_TO_B(num_to_be_allocated, sbi) >> 9;
 
 		/*
 		 * Move *clu pointer along FAT chains (hole care) because the
@@ -416,10 +414,10 @@
 
 	err = generic_write_end(file, mapping, pos, len, copied, pagep, fsdata);
 
-	if (EXFAT_I(inode)->i_size_aligned < i_size_read(inode)) {
+	if (ei->i_size_aligned < i_size_read(inode)) {
 		exfat_fs_error(inode->i_sb,
 			"invalid size(size(%llu) > aligned(%llu)\n",
-			i_size_read(inode), EXFAT_I(inode)->i_size_aligned);
+			i_size_read(inode), ei->i_size_aligned);
 		return -EIO;
 	}
 
@@ -603,8 +601,7 @@
 
 	exfat_save_attr(inode, info->attr);
 
-	inode->i_blocks = ((i_size_read(inode) + (sbi->cluster_size - 1)) &
-		~(sbi->cluster_size - 1)) >> inode->i_blkbits;
+	inode->i_blocks = round_up(i_size_read(inode), sbi->cluster_size) >> 9;
 	inode->i_mtime = info->mtime;
 	inode->i_ctime = info->mtime;
 	ei->i_crtime = info->crtime;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/namei.c
@@ -330,14 +330,20 @@
 		if (exfat_check_max_dentries(inode))
 			return -ENOSPC;
 
-		/* we trust p_dir->size regardless of FAT type */
-		if (exfat_find_last_cluster(sb, p_dir, &last_clu))
-			return -EIO;
-
 		/*
 		 * Allocate new cluster to this directory
 		 */
-		exfat_chain_set(&clu, last_clu + 1, 0, p_dir->flags);
+		if (ei->start_clu != EXFAT_EOF_CLUSTER) {
+			/* we trust p_dir->size regardless of FAT type */
+			if (exfat_find_last_cluster(sb, p_dir, &last_clu))
+				return -EIO;
+
+			exfat_chain_set(&clu, last_clu + 1, 0, p_dir->flags);
+		} else {
+			/* This directory is empty */
+			exfat_chain_set(&clu, EXFAT_EOF_CLUSTER, 0,
+					ALLOC_NO_FAT_CHAIN);
+		}
 
 		/* allocate a cluster */
 		ret = exfat_alloc_cluster(inode, 1, &clu, IS_DIRSYNC(inode));
@@ -347,6 +353,12 @@
 		if (exfat_zeroed_cluster(inode, clu.dir))
 			return -EIO;
 
+		if (ei->start_clu == EXFAT_EOF_CLUSTER) {
+			ei->start_clu = clu.dir;
+			p_dir->dir = clu.dir;
+			hint_femp.eidx = 0;
+		}
+
 		/* append to the FAT chain */
 		if (clu.flags != p_dir->flags) {
 			/* no-fat-chain bit is disabled,
@@ -395,10 +407,10 @@
 
 		/* directory inode should be updated in here */
 		i_size_write(inode, size);
-		EXFAT_I(inode)->i_size_ondisk += sbi->cluster_size;
-		EXFAT_I(inode)->i_size_aligned += sbi->cluster_size;
-		EXFAT_I(inode)->flags = p_dir->flags;
-		inode->i_blocks += 1 << sbi->sect_per_clus_bits;
+		ei->i_size_ondisk += sbi->cluster_size;
+		ei->i_size_aligned += sbi->cluster_size;
+		ei->flags = p_dir->flags;
+		inode->i_blocks += sbi->cluster_size >> 9;
 	}
 
 	return dentry;
@@ -644,7 +656,7 @@
 	info->type = exfat_get_entry_type(ep);
 	info->attr = le16_to_cpu(ep->dentry.file.attr);
 	info->size = le64_to_cpu(ep2->dentry.stream.valid_size);
-	if ((info->type == TYPE_FILE) && (info->size == 0)) {
+	if (info->size == 0) {
 		info->flags = ALLOC_NO_FAT_CHAIN;
 		info->start_clu = EXFAT_EOF_CLUSTER;
 	} else {
@@ -891,6 +903,9 @@
 
 	dentries_per_clu = sbi->dentries_per_clu;
 
+	if (p_dir->dir == EXFAT_EOF_CLUSTER)
+		return 0;
+
 	exfat_chain_dup(&clu, p_dir);
 
 	while (clu.dir != EXFAT_EOF_CLUSTER) {
@@ -1069,6 +1084,7 @@
 
 		exfat_remove_entries(inode, p_dir, oldentry, 0,
 			num_old_entries);
+		ei->dir = *p_dir;
 		ei->entry = newentry;
 	} else {
 		if (exfat_get_entry_type(epold) == TYPE_FILE) {
@@ -1159,28 +1175,6 @@
 	return 0;
 }
 
-static void exfat_update_parent_info(struct exfat_inode_info *ei,
-		struct inode *parent_inode)
-{
-	struct exfat_sb_info *sbi = EXFAT_SB(parent_inode->i_sb);
-	struct exfat_inode_info *parent_ei = EXFAT_I(parent_inode);
-	loff_t parent_isize = i_size_read(parent_inode);
-
-	/*
-	 * the problem that struct exfat_inode_info caches wrong parent info.
-	 *
-	 * because of flag-mismatch of ei->dir,
-	 * there is abnormal traversing cluster chain.
-	 */
-	if (unlikely(parent_ei->flags != ei->dir.flags ||
-		     parent_isize != EXFAT_CLU_TO_B(ei->dir.size, sbi) ||
-		     parent_ei->start_clu != ei->dir.dir)) {
-		exfat_chain_set(&ei->dir, parent_ei->start_clu,
-			EXFAT_B_TO_CLU_ROUND_UP(parent_isize, sbi),
-			parent_ei->flags);
-	}
-}
-
 /* rename or move a old file into a new file */
 static int __exfat_rename(struct inode *old_parent_inode,
 		struct exfat_inode_info *ei, struct inode *new_parent_inode,
@@ -1211,9 +1205,9 @@
 		return -ENOENT;
 	}
 
-	exfat_update_parent_info(ei, old_parent_inode);
-
-	exfat_chain_dup(&olddir, &ei->dir);
+	exfat_chain_set(&olddir, EXFAT_I(old_parent_inode)->start_clu,
+		EXFAT_B_TO_CLU_ROUND_UP(i_size_read(old_parent_inode), sbi),
+		EXFAT_I(old_parent_inode)->flags);
 	dentry = ei->entry;
 
 	ep = exfat_get_dentry(sb, &olddir, dentry, &old_bh, NULL);
@@ -1233,8 +1227,6 @@
 			goto out;
 		}
 
-		exfat_update_parent_info(new_ei, new_parent_inode);
-
 		p_dir = &(new_ei->dir);
 		new_entry = new_ei->entry;
 		ep = exfat_get_dentry(sb, p_dir, new_entry, &new_bh, NULL);
@@ -1297,7 +1289,8 @@
 		}
 
 		/* Free the clusters if new_inode is a dir(as if exfat_rmdir) */
-		if (new_entry_type == TYPE_DIR) {
+		if (new_entry_type == TYPE_DIR &&
+		    new_ei->start_clu != EXFAT_EOF_CLUSTER) {
 			/* new_ei, new_clu_to_free */
 			struct exfat_chain new_clu_to_free;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exfat/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exfat/super.c
@@ -364,11 +364,10 @@
 	inode->i_op = &exfat_dir_inode_operations;
 	inode->i_fop = &exfat_dir_operations;
 
-	inode->i_blocks = ((i_size_read(inode) + (sbi->cluster_size - 1))
-			& ~(sbi->cluster_size - 1)) >> inode->i_blkbits;
-	EXFAT_I(inode)->i_pos = ((loff_t)sbi->root_dir << 32) | 0xffffffff;
-	EXFAT_I(inode)->i_size_aligned = i_size_read(inode);
-	EXFAT_I(inode)->i_size_ondisk = i_size_read(inode);
+	inode->i_blocks = round_up(i_size_read(inode), sbi->cluster_size) >> 9;
+	ei->i_pos = ((loff_t)sbi->root_dir << 32) | 0xffffffff;
+	ei->i_size_aligned = i_size_read(inode);
+	ei->i_size_ondisk = i_size_read(inode);
 
 	exfat_save_attr(inode, ATTR_SUBDIR);
 	inode->i_mtime = inode->i_atime = inode->i_ctime = ei->i_crtime =
--- linux-xilinx-zynqmp-5.15.0.orig/fs/exportfs/expfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/exportfs/expfs.c
@@ -18,7 +18,7 @@
 #include <linux/sched.h>
 #include <linux/cred.h>
 
-#define dprintk(fmt, args...) do{}while(0)
+#define dprintk(fmt, args...) pr_debug(fmt, ##args)
 
 
 static int get_name(const struct path *path, char *name, struct dentry *child);
@@ -132,8 +132,8 @@
 	inode_unlock(dentry->d_inode);
 
 	if (IS_ERR(parent)) {
-		dprintk("%s: get_parent of %ld failed, err %d\n",
-			__func__, dentry->d_inode->i_ino, PTR_ERR(parent));
+		dprintk("get_parent of %lu failed, err %ld\n",
+			dentry->d_inode->i_ino, PTR_ERR(parent));
 		return parent;
 	}
 
@@ -145,9 +145,9 @@
 	if (err)
 		goto out_err;
 	dprintk("%s: found name: %s\n", __func__, nbuf);
-	tmp = lookup_one_len_unlocked(nbuf, parent, strlen(nbuf));
+	tmp = lookup_one_unlocked(mnt_user_ns(mnt), nbuf, parent, strlen(nbuf));
 	if (IS_ERR(tmp)) {
-		dprintk("%s: lookup failed: %d\n", __func__, PTR_ERR(tmp));
+		dprintk("lookup failed: %ld\n", PTR_ERR(tmp));
 		err = PTR_ERR(tmp);
 		goto out_err;
 	}
@@ -525,7 +525,8 @@
 		}
 
 		inode_lock(target_dir->d_inode);
-		nresult = lookup_one_len(nbuf, target_dir, strlen(nbuf));
+		nresult = lookup_one(mnt_user_ns(mnt), nbuf,
+				     target_dir, strlen(nbuf));
 		if (!IS_ERR(nresult)) {
 			if (unlikely(nresult->d_inode != result->d_inode)) {
 				dput(nresult);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext2/balloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext2/balloc.c
@@ -79,26 +79,33 @@
 	ext2_grpblk_t next_zero_bit;
 	ext2_fsblk_t bitmap_blk;
 	ext2_fsblk_t group_first_block;
+	ext2_grpblk_t max_bit;
 
 	group_first_block = ext2_group_first_block_no(sb, block_group);
+	max_bit = ext2_group_last_block_no(sb, block_group) - group_first_block;
 
 	/* check whether block bitmap block number is set */
 	bitmap_blk = le32_to_cpu(desc->bg_block_bitmap);
 	offset = bitmap_blk - group_first_block;
-	if (!ext2_test_bit(offset, bh->b_data))
+	if (offset < 0 || offset > max_bit ||
+	    !ext2_test_bit(offset, bh->b_data))
 		/* bad block bitmap */
 		goto err_out;
 
 	/* check whether the inode bitmap block number is set */
 	bitmap_blk = le32_to_cpu(desc->bg_inode_bitmap);
 	offset = bitmap_blk - group_first_block;
-	if (!ext2_test_bit(offset, bh->b_data))
+	if (offset < 0 || offset > max_bit ||
+	    !ext2_test_bit(offset, bh->b_data))
 		/* bad block bitmap */
 		goto err_out;
 
 	/* check whether the inode table block number is set */
 	bitmap_blk = le32_to_cpu(desc->bg_inode_table);
 	offset = bitmap_blk - group_first_block;
+	if (offset < 0 || offset > max_bit ||
+	    offset + EXT2_SB(sb)->s_itb_per_group - 1 > max_bit)
+		goto err_out;
 	next_zero_bit = ext2_find_next_zero_bit(bh->b_data,
 				offset + EXT2_SB(sb)->s_itb_per_group,
 				offset);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext2/ext2.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext2/ext2.h
@@ -70,10 +70,7 @@
  * second extended-fs super-block data in memory
  */
 struct ext2_sb_info {
-	unsigned long s_frag_size;	/* Size of a fragment in bytes */
-	unsigned long s_frags_per_block;/* Number of fragments per block */
 	unsigned long s_inodes_per_block;/* Number of inodes per block */
-	unsigned long s_frags_per_group;/* Number of fragments in a group */
 	unsigned long s_blocks_per_group;/* Number of blocks in a group */
 	unsigned long s_inodes_per_group;/* Number of inodes in a group */
 	unsigned long s_itb_per_group;	/* Number of inode table blocks per group */
@@ -179,6 +176,7 @@
 #define EXT2_MIN_BLOCK_SIZE		1024
 #define	EXT2_MAX_BLOCK_SIZE		4096
 #define EXT2_MIN_BLOCK_LOG_SIZE		  10
+#define EXT2_MAX_BLOCK_LOG_SIZE		  16
 #define EXT2_BLOCK_SIZE(s)		((s)->s_blocksize)
 #define	EXT2_ADDR_PER_BLOCK(s)		(EXT2_BLOCK_SIZE(s) / sizeof (__u32))
 #define EXT2_BLOCK_SIZE_BITS(s)		((s)->s_blocksize_bits)
@@ -187,15 +185,6 @@
 #define EXT2_FIRST_INO(s)		(EXT2_SB(s)->s_first_ino)
 
 /*
- * Macro-instructions used to manage fragments
- */
-#define EXT2_MIN_FRAG_SIZE		1024
-#define	EXT2_MAX_FRAG_SIZE		4096
-#define EXT2_MIN_FRAG_LOG_SIZE		  10
-#define EXT2_FRAG_SIZE(s)		(EXT2_SB(s)->s_frag_size)
-#define EXT2_FRAGS_PER_BLOCK(s)		(EXT2_SB(s)->s_frags_per_block)
-
-/*
  * Structure of a blocks group descriptor
  */
 struct ext2_group_desc
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext2/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext2/super.c
@@ -163,7 +163,7 @@
 	db_count = sbi->s_gdb_count;
 	for (i = 0; i < db_count; i++)
 		brelse(sbi->s_group_desc[i]);
-	kfree(sbi->s_group_desc);
+	kvfree(sbi->s_group_desc);
 	kfree(sbi->s_debts);
 	percpu_counter_destroy(&sbi->s_freeblocks_counter);
 	percpu_counter_destroy(&sbi->s_freeinodes_counter);
@@ -670,10 +670,9 @@
 		es->s_max_mnt_count = cpu_to_le16(EXT2_DFL_MAX_MNT_COUNT);
 	le16_add_cpu(&es->s_mnt_count, 1);
 	if (test_opt (sb, DEBUG))
-		ext2_msg(sb, KERN_INFO, "%s, %s, bs=%lu, fs=%lu, gc=%lu, "
+		ext2_msg(sb, KERN_INFO, "%s, %s, bs=%lu, gc=%lu, "
 			"bpg=%lu, ipg=%lu, mo=%04lx]",
 			EXT2FS_VERSION, EXT2FS_DATE, sb->s_blocksize,
-			sbi->s_frag_size,
 			sbi->s_groups_count,
 			EXT2_BLOCKS_PER_GROUP(sb),
 			EXT2_INODES_PER_GROUP(sb),
@@ -753,8 +752,12 @@
 	res += 1LL << (bits-2);
 	res += 1LL << (2*(bits-2));
 	res += 1LL << (3*(bits-2));
+	/* Compute how many metadata blocks are needed */
+	meta_blocks = 1;
+	meta_blocks += 1 + ppb;
+	meta_blocks += 1 + ppb + ppb * ppb;
 	/* Does block tree limit file size? */
-	if (res < upper_limit)
+	if (res + meta_blocks <= upper_limit)
 		goto check_lfs;
 
 	res = upper_limit;
@@ -943,6 +946,13 @@
 		goto failed_mount;
 	}
 
+	if (le32_to_cpu(es->s_log_block_size) >
+	    (EXT2_MAX_BLOCK_LOG_SIZE - BLOCK_SIZE_BITS)) {
+		ext2_msg(sb, KERN_ERR,
+			 "Invalid log block size: %u",
+			 le32_to_cpu(es->s_log_block_size));
+		goto failed_mount;
+	}
 	blocksize = BLOCK_SIZE << le32_to_cpu(sbi->s_es->s_log_block_size);
 
 	if (test_opt(sb, DAX)) {
@@ -1001,14 +1011,7 @@
 		}
 	}
 
-	sbi->s_frag_size = EXT2_MIN_FRAG_SIZE <<
-				   le32_to_cpu(es->s_log_frag_size);
-	if (sbi->s_frag_size == 0)
-		goto cantfind_ext2;
-	sbi->s_frags_per_block = sb->s_blocksize / sbi->s_frag_size;
-
 	sbi->s_blocks_per_group = le32_to_cpu(es->s_blocks_per_group);
-	sbi->s_frags_per_group = le32_to_cpu(es->s_frags_per_group);
 	sbi->s_inodes_per_group = le32_to_cpu(es->s_inodes_per_group);
 
 	sbi->s_inodes_per_block = sb->s_blocksize / EXT2_INODE_SIZE(sb);
@@ -1034,11 +1037,10 @@
 		goto failed_mount;
 	}
 
-	if (sb->s_blocksize != sbi->s_frag_size) {
+	if (es->s_log_frag_size != es->s_log_block_size) {
 		ext2_msg(sb, KERN_ERR,
-			"error: fragsize %lu != blocksize %lu"
-			"(not supported yet)",
-			sbi->s_frag_size, sb->s_blocksize);
+			"error: fragsize log %u != blocksize log %u",
+			le32_to_cpu(es->s_log_frag_size), sb->s_blocksize_bits);
 		goto failed_mount;
 	}
 
@@ -1048,15 +1050,10 @@
 			sbi->s_blocks_per_group);
 		goto failed_mount;
 	}
-	if (sbi->s_frags_per_group > sb->s_blocksize * 8) {
-		ext2_msg(sb, KERN_ERR,
-			"error: #fragments per group too big: %lu",
-			sbi->s_frags_per_group);
-		goto failed_mount;
-	}
-	if (sbi->s_inodes_per_group > sb->s_blocksize * 8) {
+	if (sbi->s_inodes_per_group < sbi->s_inodes_per_block ||
+	    sbi->s_inodes_per_group > sb->s_blocksize * 8) {
 		ext2_msg(sb, KERN_ERR,
-			"error: #inodes per group too big: %lu",
+			"error: invalid #inodes per group: %lu",
 			sbi->s_inodes_per_group);
 		goto failed_mount;
 	}
@@ -1066,9 +1063,16 @@
 	sbi->s_groups_count = ((le32_to_cpu(es->s_blocks_count) -
 				le32_to_cpu(es->s_first_data_block) - 1)
 					/ EXT2_BLOCKS_PER_GROUP(sb)) + 1;
+	if ((u64)sbi->s_groups_count * sbi->s_inodes_per_group !=
+	    le32_to_cpu(es->s_inodes_count)) {
+		ext2_msg(sb, KERN_ERR, "error: invalid #inodes: %u vs computed %llu",
+			 le32_to_cpu(es->s_inodes_count),
+			 (u64)sbi->s_groups_count * sbi->s_inodes_per_group);
+		goto failed_mount;
+	}
 	db_count = (sbi->s_groups_count + EXT2_DESC_PER_BLOCK(sb) - 1) /
 		   EXT2_DESC_PER_BLOCK(sb);
-	sbi->s_group_desc = kmalloc_array(db_count,
+	sbi->s_group_desc = kvmalloc_array(db_count,
 					   sizeof(struct buffer_head *),
 					   GFP_KERNEL);
 	if (sbi->s_group_desc == NULL) {
@@ -1194,7 +1198,7 @@
 	for (i = 0; i < db_count; i++)
 		brelse(sbi->s_group_desc[i]);
 failed_mount_group_desc:
-	kfree(sbi->s_group_desc);
+	kvfree(sbi->s_group_desc);
 	kfree(sbi->s_debts);
 failed_mount:
 	brelse(bh);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext2/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext2/xattr.c
@@ -694,10 +694,10 @@
 			/* We need to allocate a new block */
 			ext2_fsblk_t goal = ext2_group_first_block_no(sb,
 						EXT2_I(inode)->i_block_group);
-			int block = ext2_new_block(inode, goal, &error);
+			ext2_fsblk_t block = ext2_new_block(inode, goal, &error);
 			if (error)
 				goto cleanup;
-			ea_idebug(inode, "creating block %d", block);
+			ea_idebug(inode, "creating block %lu", block);
 
 			new_bh = sb_getblk(sb, block);
 			if (unlikely(!new_bh)) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/acl.c
@@ -246,7 +246,6 @@
 	handle = ext4_journal_start(inode, EXT4_HT_XATTR, credits);
 	if (IS_ERR(handle))
 		return PTR_ERR(handle);
-	ext4_fc_start_update(inode);
 
 	if ((type == ACL_TYPE_ACCESS) && acl) {
 		error = posix_acl_update_mode(mnt_userns, inode, &mode, &acl);
@@ -264,7 +263,6 @@
 	}
 out_stop:
 	ext4_journal_stop(handle);
-	ext4_fc_stop_update(inode);
 	if (error == -ENOSPC && ext4_should_retry_alloc(inode->i_sb, &retries))
 		goto retry;
 	return error;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/acl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/acl.h
@@ -68,6 +68,11 @@
 static inline int
 ext4_init_acl(handle_t *handle, struct inode *inode, struct inode *dir)
 {
+	/* usually, the umask is applied by posix_acl_create(), but if
+	   ext4 ACL support is disabled at compile time, we need to do
+	   it here, because posix_acl_create() will never be called */
+	inode->i_mode &= ~current_umask();
+
 	return 0;
 }
 #endif  /* CONFIG_EXT4_FS_POSIX_ACL */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/balloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/balloc.c
@@ -303,6 +303,36 @@
 	return desc;
 }
 
+static ext4_fsblk_t ext4_valid_block_bitmap_padding(struct super_block *sb,
+						    ext4_group_t block_group,
+						    struct buffer_head *bh)
+{
+	ext4_grpblk_t next_zero_bit;
+	unsigned long bitmap_size = sb->s_blocksize * 8;
+	unsigned int offset = num_clusters_in_group(sb, block_group);
+
+	if (bitmap_size <= offset)
+		return 0;
+
+	next_zero_bit = ext4_find_next_zero_bit(bh->b_data, bitmap_size, offset);
+
+	return (next_zero_bit < bitmap_size ? next_zero_bit : 0);
+}
+
+struct ext4_group_info *ext4_get_group_info(struct super_block *sb,
+					    ext4_group_t group)
+{
+	struct ext4_group_info **grp_info;
+	long indexv, indexh;
+
+	if (unlikely(group >= EXT4_SB(sb)->s_groups_count))
+		return NULL;
+	indexv = group >> (EXT4_DESC_PER_BLOCK_BITS(sb));
+	indexh = group & ((EXT4_DESC_PER_BLOCK(sb)) - 1);
+	grp_info = sbi_array_rcu_deref(EXT4_SB(sb), s_group_info, indexv);
+	return grp_info[indexh];
+}
+
 /*
  * Return the block number which was discovered to be invalid, or 0 if
  * the block bitmap is valid.
@@ -377,7 +407,7 @@
 
 	if (buffer_verified(bh))
 		return 0;
-	if (EXT4_MB_GRP_BBITMAP_CORRUPT(grp))
+	if (!grp || EXT4_MB_GRP_BBITMAP_CORRUPT(grp))
 		return -EFSCORRUPTED;
 
 	ext4_lock_group(sb, block_group);
@@ -401,6 +431,15 @@
 					EXT4_GROUP_INFO_BBITMAP_CORRUPT);
 		return -EFSCORRUPTED;
 	}
+	blk = ext4_valid_block_bitmap_padding(sb, block_group, bh);
+	if (unlikely(blk != 0)) {
+		ext4_unlock_group(sb, block_group);
+		ext4_error(sb, "bg %u: block %llu: padding at end of block bitmap is not set",
+			   block_group, blk);
+		ext4_mark_group_bitmap_corrupted(sb, block_group,
+						 EXT4_GROUP_INFO_BBITMAP_CORRUPT);
+		return -EFSCORRUPTED;
+	}
 	set_buffer_verified(bh);
 verified:
 	ext4_unlock_group(sb, block_group);
@@ -665,7 +704,7 @@
 	 * it's possible we've just missed a transaction commit here,
 	 * so ignore the returned status
 	 */
-	jbd_debug(1, "%s: retrying operation after ENOSPC\n", sb->s_id);
+	ext4_debug("%s: retrying operation after ENOSPC\n", sb->s_id);
 	(void) jbd2_journal_force_commit_nested(sbi->s_journal);
 	return 1;
 }
@@ -870,11 +909,11 @@
 }
 
 /*
- * This function returns the number of file system metadata clusters at
+ * This function returns the number of file system metadata blocks at
  * the beginning of a block group, including the reserved gdt blocks.
  */
-static unsigned ext4_num_base_meta_clusters(struct super_block *sb,
-				     ext4_group_t block_group)
+unsigned int ext4_num_base_meta_blocks(struct super_block *sb,
+				       ext4_group_t block_group)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	unsigned num;
@@ -892,8 +931,15 @@
 	} else { /* For META_BG_BLOCK_GROUPS */
 		num += ext4_bg_num_gdb(sb, block_group);
 	}
-	return EXT4_NUM_B2C(sbi, num);
+	return num;
 }
+
+static unsigned int ext4_num_base_meta_clusters(struct super_block *sb,
+						ext4_group_t block_group)
+{
+	return EXT4_NUM_B2C(EXT4_SB(sb), ext4_num_base_meta_blocks(sb, block_group));
+}
+
 /**
  *	ext4_inode_to_goal_block - return a hint for block allocation
  *	@inode: inode for block allocation
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/block_validity.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/block_validity.c
@@ -215,7 +215,6 @@
 	struct ext4_system_blocks *system_blks;
 	struct ext4_group_desc *gdp;
 	ext4_group_t i;
-	int flex_size = ext4_flex_bg_size(sbi);
 	int ret;
 
 	system_blks = kzalloc(sizeof(*system_blks), GFP_KERNEL);
@@ -223,12 +222,13 @@
 		return -ENOMEM;
 
 	for (i=0; i < ngroups; i++) {
+		unsigned int meta_blks = ext4_num_base_meta_blocks(sb, i);
+
 		cond_resched();
-		if (ext4_bg_has_super(sb, i) &&
-		    ((i < 5) || ((i % flex_size) == 0))) {
+		if (meta_blks != 0) {
 			ret = add_system_zone(system_blks,
 					ext4_group_first_block_no(sb, i),
-					ext4_bg_num_gdb(sb, i) + 1, 0);
+					meta_blks, 0);
 			if (ret)
 				goto err;
 		}
@@ -292,15 +292,10 @@
 		call_rcu(&system_blks->rcu, ext4_destroy_system_zone);
 }
 
-/*
- * Returns 1 if the passed-in block region (start_blk,
- * start_blk+count) is valid; 0 if some part of the block region
- * overlaps with some other filesystem metadata blocks.
- */
-int ext4_inode_block_valid(struct inode *inode, ext4_fsblk_t start_blk,
-			  unsigned int count)
+int ext4_sb_block_valid(struct super_block *sb, struct inode *inode,
+				ext4_fsblk_t start_blk, unsigned int count)
 {
-	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	struct ext4_system_blocks *system_blks;
 	struct ext4_system_zone *entry;
 	struct rb_node *n;
@@ -329,7 +324,9 @@
 		else if (start_blk >= (entry->start_blk + entry->count))
 			n = n->rb_right;
 		else {
-			ret = (entry->ino == inode->i_ino);
+			ret = 0;
+			if (inode)
+				ret = (entry->ino == inode->i_ino);
 			break;
 		}
 	}
@@ -338,6 +335,17 @@
 	return ret;
 }
 
+/*
+ * Returns 1 if the passed-in block region (start_blk,
+ * start_blk+count) is valid; 0 if some part of the block region
+ * overlaps with some other filesystem metadata blocks.
+ */
+int ext4_inode_block_valid(struct inode *inode, ext4_fsblk_t start_blk,
+			  unsigned int count)
+{
+	return ext4_sb_block_valid(inode->i_sb, inode, start_blk, count);
+}
+
 int ext4_check_blockref(const char *function, unsigned int line,
 			struct inode *inode, __le32 *p, unsigned int max)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/dir.c
@@ -104,6 +104,9 @@
 	else if (unlikely(le32_to_cpu(de->inode) >
 			le32_to_cpu(EXT4_SB(dir->i_sb)->s_es->s_inodes_count)))
 		error_msg = "inode out of bounds";
+	else if (unlikely(next_offset == size && de->name_len == 1 &&
+			  de->name[0] == '.'))
+		error_msg = "'.' directory cannot be the last in data block";
 	else
 		return 0;
 
@@ -279,12 +282,20 @@
 					struct fscrypt_str de_name =
 							FSTR_INIT(de->name,
 								de->name_len);
+					u32 hash;
+					u32 minor_hash;
+
+					if (IS_CASEFOLDED(inode)) {
+						hash = EXT4_DIRENT_HASH(de);
+						minor_hash = EXT4_DIRENT_MINOR_HASH(de);
+					} else {
+						hash = 0;
+						minor_hash = 0;
+					}
 
 					/* Directory is encrypted */
 					err = fscrypt_fname_disk_to_usr(inode,
-						EXT4_DIRENT_HASH(de),
-						EXT4_DIRENT_MINOR_HASH(de),
-						&de_name, &fstr);
+						hash, minor_hash, &de_name, &fstr);
 					de_name = fstr;
 					fstr.len = save_len;
 					if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/ext4.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/ext4.h
@@ -559,7 +559,7 @@
  *
  * It's not paranoia if the Murphy's Law really *is* out to get you.  :-)
  */
-#define TEST_FLAG_VALUE(FLAG) (EXT4_##FLAG##_FL == (1 << EXT4_INODE_##FLAG))
+#define TEST_FLAG_VALUE(FLAG) (EXT4_##FLAG##_FL == (1U << EXT4_INODE_##FLAG))
 #define CHECK_FLAG_VALUE(FLAG) BUILD_BUG_ON(!TEST_FLAG_VALUE(FLAG))
 
 static inline void ext4_check_flag_values(void)
@@ -995,11 +995,13 @@
  *			  where the second inode has larger inode number
  *			  than the first
  *  I_DATA_SEM_QUOTA  - Used for quota inodes only
+ *  I_DATA_SEM_EA     - Used for ea_inodes only
  */
 enum {
 	I_DATA_SEM_NORMAL = 0,
 	I_DATA_SEM_OTHER,
 	I_DATA_SEM_QUOTA,
+	I_DATA_SEM_EA
 };
 
 
@@ -1435,12 +1437,6 @@
 
 #ifdef __KERNEL__
 
-#ifdef CONFIG_FS_ENCRYPTION
-#define DUMMY_ENCRYPTION_ENABLED(sbi) ((sbi)->s_dummy_enc_policy.policy != NULL)
-#else
-#define DUMMY_ENCRYPTION_ENABLED(sbi) (0)
-#endif
-
 /* Number of quota types we support */
 #define EXT4_MAXQUOTAS 3
 
@@ -1660,7 +1656,7 @@
 	struct task_struct *s_mmp_tsk;
 
 	/* record the last minlen when FITRIM is called. */
-	atomic_t s_last_trim_minblks;
+	unsigned long s_last_trim_minblks;
 
 	/* Reference to checksum algorithm driver via cryptoapi */
 	struct crypto_shash *s_chksum_driver;
@@ -1724,9 +1720,9 @@
 	 */
 	struct work_struct s_error_work;
 
-	/* Ext4 fast commit stuff */
+	/* Ext4 fast commit sub transaction ID */
 	atomic_t s_fc_subtid;
-	atomic_t s_fc_ineligible_updates;
+
 	/*
 	 * After commit starts, the main queue gets locked, and the further
 	 * updates get added in the staging queue.
@@ -1746,7 +1742,7 @@
 	spinlock_t s_fc_lock;
 	struct buffer_head *s_fc_bh;
 	struct ext4_fc_stats s_fc_stats;
-	u64 s_fc_avg_commit_time;
+	tid_t s_fc_ineligible_tid;
 #ifdef CONFIG_EXT4_DEBUG
 	int s_fc_debug_max_replay;
 #endif
@@ -1792,10 +1788,7 @@
 enum {
 	EXT4_MF_MNTDIR_SAMPLED,
 	EXT4_MF_FS_ABORTED,	/* Fatal error detected */
-	EXT4_MF_FC_INELIGIBLE,	/* Fast commit ineligible */
-	EXT4_MF_FC_COMMITTING	/* File system underoing a fast
-				 * commit.
-				 */
+	EXT4_MF_FC_INELIGIBLE	/* Fast commit ineligible */
 };
 
 static inline void ext4_set_mount_flag(struct super_block *sb, int bit)
@@ -2270,6 +2263,10 @@
  * Structure of a directory entry
  */
 #define EXT4_NAME_LEN 255
+/*
+ * Base length of the ext4 directory entry excluding the name length
+ */
+#define EXT4_BASE_DIR_LEN (sizeof(struct ext4_dir_entry_2) - EXT4_NAME_LEN)
 
 struct ext4_dir_entry {
 	__le32	inode;			/* Inode number */
@@ -2704,6 +2701,8 @@
 extern struct ext4_group_desc * ext4_get_group_desc(struct super_block * sb,
 						    ext4_group_t block_group,
 						    struct buffer_head ** bh);
+extern struct ext4_group_info *ext4_get_group_info(struct super_block *sb,
+						   ext4_group_t group);
 extern int ext4_should_retry_alloc(struct super_block *sb, int *retries);
 
 extern struct buffer_head *ext4_read_block_bitmap_nowait(struct super_block *sb,
@@ -2924,9 +2923,7 @@
 			    struct dentry *dentry);
 void ext4_fc_track_create(handle_t *handle, struct dentry *dentry);
 void ext4_fc_track_inode(handle_t *handle, struct inode *inode);
-void ext4_fc_mark_ineligible(struct super_block *sb, int reason);
-void ext4_fc_start_ineligible(struct super_block *sb, int reason);
-void ext4_fc_stop_ineligible(struct super_block *sb);
+void ext4_fc_mark_ineligible(struct super_block *sb, int reason, handle_t *handle);
 void ext4_fc_start_update(struct inode *inode);
 void ext4_fc_stop_update(struct inode *inode);
 void ext4_fc_del(struct inode *inode);
@@ -2934,6 +2931,10 @@
 void ext4_fc_replay_cleanup(struct super_block *sb);
 int ext4_fc_commit(journal_t *journal, tid_t commit_tid);
 int __init ext4_fc_init_dentry_cache(void);
+void ext4_fc_destroy_dentry_cache(void);
+int ext4_fc_record_regions(struct super_block *sb, int ino,
+			   ext4_lblk_t lblk, ext4_fsblk_t pblk,
+			   int len, int replay);
 
 /* mballoc.c */
 extern const struct seq_operations ext4_mb_seq_groups_ops;
@@ -2999,7 +3000,9 @@
 typedef enum {
 	EXT4_IGET_NORMAL =	0,
 	EXT4_IGET_SPECIAL =	0x0001, /* OK to iget a system inode */
-	EXT4_IGET_HANDLE = 	0x0002	/* Inode # is from a handle */
+	EXT4_IGET_HANDLE = 	0x0002,	/* Inode # is from a handle */
+	EXT4_IGET_BAD =		0x0004, /* Allow to iget a bad inode */
+	EXT4_IGET_EA_INODE =	0x0008	/* Inode should contain an EA value */
 } ext4_iget_flags;
 
 extern struct inode *__ext4_iget(struct super_block *sb, unsigned long ino,
@@ -3028,7 +3031,7 @@
 extern int ext4_can_truncate(struct inode *inode);
 extern int ext4_truncate(struct inode *);
 extern int ext4_break_layouts(struct inode *);
-extern int ext4_punch_hole(struct inode *inode, loff_t offset, loff_t length);
+extern int ext4_punch_hole(struct file *file, loff_t offset, loff_t length);
 extern void ext4_set_inode_flags(struct inode *, bool init);
 extern int ext4_alloc_da_blocks(struct inode *inode);
 extern void ext4_set_aops(struct inode *inode);
@@ -3109,6 +3112,8 @@
 extern void ext4_sb_breadahead_unmovable(struct super_block *sb, sector_t block);
 extern int ext4_seq_options_show(struct seq_file *seq, void *offset);
 extern int ext4_calculate_overhead(struct super_block *sb);
+extern __le32 ext4_superblock_csum(struct super_block *sb,
+				struct ext4_super_block *es);
 extern void ext4_superblock_csum_set(struct super_block *sb);
 extern int ext4_alloc_flex_bg_array(struct super_block *sb,
 				    ext4_group_t ngroup);
@@ -3117,6 +3122,8 @@
 extern void ext4_mark_group_bitmap_corrupted(struct super_block *sb,
 					     ext4_group_t block_group,
 					     unsigned int flags);
+extern unsigned int ext4_num_base_meta_blocks(struct super_block *sb,
+					      ext4_group_t block_group);
 
 extern __printf(7, 8)
 void __ext4_error(struct super_block *, const char *, unsigned int, bool,
@@ -3348,19 +3355,6 @@
 	raw_inode->i_size_high = cpu_to_le32(i_size >> 32);
 }
 
-static inline
-struct ext4_group_info *ext4_get_group_info(struct super_block *sb,
-					    ext4_group_t group)
-{
-	 struct ext4_group_info **grp_info;
-	 long indexv, indexh;
-	 BUG_ON(group >= EXT4_SB(sb)->s_groups_count);
-	 indexv = group >> (EXT4_DESC_PER_BLOCK_BITS(sb));
-	 indexh = group & ((EXT4_DESC_PER_BLOCK(sb)) - 1);
-	 grp_info = sbi_array_rcu_deref(EXT4_SB(sb), s_group_info, indexv);
-	 return grp_info[indexh];
-}
-
 /*
  * Reading s_groups_count requires using smp_rmb() afterwards.  See
  * the locking protocol documented in the comments of ext4_group_add()
@@ -3649,8 +3643,8 @@
 					unsigned int blocksize);
 extern int ext4_handle_dirty_dirblock(handle_t *handle, struct inode *inode,
 				      struct buffer_head *bh);
-extern int __ext4_unlink(handle_t *handle, struct inode *dir, const struct qstr *d_name,
-			 struct inode *inode);
+extern int __ext4_unlink(struct inode *dir, const struct qstr *d_name,
+			 struct inode *inode, struct dentry *dentry);
 extern int __ext4_link(struct inode *dir, struct inode *inode,
 		       struct dentry *dentry);
 
@@ -3700,6 +3694,9 @@
 				  unsigned int count);
 extern int ext4_check_blockref(const char *, unsigned int,
 			       struct inode *, __le32 *, unsigned int);
+extern int ext4_sb_block_valid(struct super_block *sb, struct inode *inode,
+				ext4_fsblk_t start_blk, unsigned int count);
+
 
 /* extents.c */
 struct ext4_ext_path;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/ext4_jbd2.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/ext4_jbd2.c
@@ -162,6 +162,8 @@
 {
 	if (!ext4_handle_valid(handle))
 		return 0;
+	if (is_handle_aborted(handle))
+		return -EROFS;
 	if (jbd2_handle_buffer_credits(handle) >= check_cred &&
 	    handle->h_revoke_credits >= revoke_cred)
 		return 0;
@@ -265,8 +267,7 @@
 	trace_ext4_forget(inode, is_metadata, blocknr);
 	BUFFER_TRACE(bh, "enter");
 
-	jbd_debug(4, "forgetting bh %p: is_metadata = %d, mode %o, "
-		  "data mode %x\n",
+	ext4_debug("forgetting bh %p: is_metadata=%d, mode %o, data mode %x\n",
 		  bh, is_metadata, inode->i_mode,
 		  test_opt(inode->i_sb, DATA_FLAGS));
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/extents.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/extents.c
@@ -136,15 +136,25 @@
 static int ext4_ext_get_access(handle_t *handle, struct inode *inode,
 				struct ext4_ext_path *path)
 {
+	int err = 0;
+
 	if (path->p_bh) {
 		/* path points to block */
 		BUFFER_TRACE(path->p_bh, "get_write_access");
-		return ext4_journal_get_write_access(handle, inode->i_sb,
-						     path->p_bh, EXT4_JTR_NONE);
+		err = ext4_journal_get_write_access(handle, inode->i_sb,
+						    path->p_bh, EXT4_JTR_NONE);
+		/*
+		 * The extent buffer's verified bit will be set again in
+		 * __ext4_ext_dirty(). We could leave an inconsistent
+		 * buffer if the extents updating procudure break off du
+		 * to some error happens, force to check it again.
+		 */
+		if (!err)
+			clear_buffer_verified(path->p_bh);
 	}
 	/* path points to leaf/index in inode body */
 	/* we use in-core data, no need to protect them */
-	return 0;
+	return err;
 }
 
 /*
@@ -165,6 +175,9 @@
 		/* path points to block */
 		err = __ext4_handle_dirty_metadata(where, line, handle,
 						   inode, path->p_bh);
+		/* Extents updating done, re-set verified flag */
+		if (!err)
+			set_buffer_verified(path->p_bh);
 	} else {
 		/* path points to leaf/index in inode body */
 		err = ext4_mark_inode_dirty(handle, inode);
@@ -354,9 +367,13 @@
 
 static int ext4_valid_extent_entries(struct inode *inode,
 				     struct ext4_extent_header *eh,
-				     ext4_fsblk_t *pblk, int depth)
+				     ext4_lblk_t lblk, ext4_fsblk_t *pblk,
+				     int depth)
 {
 	unsigned short entries;
+	ext4_lblk_t lblock = 0;
+	ext4_lblk_t cur = 0;
+
 	if (eh->eh_entries == 0)
 		return 1;
 
@@ -365,31 +382,51 @@
 	if (depth == 0) {
 		/* leaf entries */
 		struct ext4_extent *ext = EXT_FIRST_EXTENT(eh);
-		ext4_lblk_t lblock = 0;
-		ext4_lblk_t prev = 0;
-		int len = 0;
+
+		/*
+		 * The logical block in the first entry should equal to
+		 * the number in the index block.
+		 */
+		if (depth != ext_depth(inode) &&
+		    lblk != le32_to_cpu(ext->ee_block))
+			return 0;
 		while (entries) {
 			if (!ext4_valid_extent(inode, ext))
 				return 0;
 
 			/* Check for overlapping extents */
 			lblock = le32_to_cpu(ext->ee_block);
-			len = ext4_ext_get_actual_len(ext);
-			if ((lblock <= prev) && prev) {
+			if (lblock < cur) {
 				*pblk = ext4_ext_pblock(ext);
 				return 0;
 			}
+			cur = lblock + ext4_ext_get_actual_len(ext);
 			ext++;
 			entries--;
-			prev = lblock + len - 1;
 		}
 	} else {
 		struct ext4_extent_idx *ext_idx = EXT_FIRST_INDEX(eh);
+
+		/*
+		 * The logical block in the first entry should equal to
+		 * the number in the parent index block.
+		 */
+		if (depth != ext_depth(inode) &&
+		    lblk != le32_to_cpu(ext_idx->ei_block))
+			return 0;
 		while (entries) {
 			if (!ext4_valid_extent_idx(inode, ext_idx))
 				return 0;
+
+			/* Check for overlapping index extents */
+			lblock = le32_to_cpu(ext_idx->ei_block);
+			if (lblock < cur) {
+				*pblk = ext4_idx_pblock(ext_idx);
+				return 0;
+			}
 			ext_idx++;
 			entries--;
+			cur = lblock + 1;
 		}
 	}
 	return 1;
@@ -397,7 +434,7 @@
 
 static int __ext4_ext_check(const char *function, unsigned int line,
 			    struct inode *inode, struct ext4_extent_header *eh,
-			    int depth, ext4_fsblk_t pblk)
+			    int depth, ext4_fsblk_t pblk, ext4_lblk_t lblk)
 {
 	const char *error_msg;
 	int max = 0, err = -EFSCORRUPTED;
@@ -423,7 +460,11 @@
 		error_msg = "invalid eh_entries";
 		goto corrupted;
 	}
-	if (!ext4_valid_extent_entries(inode, eh, &pblk, depth)) {
+	if (unlikely((eh->eh_entries == 0) && (depth > 0))) {
+		error_msg = "eh_entries is 0 but eh_depth is > 0";
+		goto corrupted;
+	}
+	if (!ext4_valid_extent_entries(inode, eh, lblk, &pblk, depth)) {
 		error_msg = "invalid extent entries";
 		goto corrupted;
 	}
@@ -453,7 +494,7 @@
 }
 
 #define ext4_ext_check(inode, eh, depth, pblk)			\
-	__ext4_ext_check(__func__, __LINE__, (inode), (eh), (depth), (pblk))
+	__ext4_ext_check(__func__, __LINE__, (inode), (eh), (depth), (pblk), 0)
 
 int ext4_ext_check_inode(struct inode *inode)
 {
@@ -486,16 +527,18 @@
 
 static struct buffer_head *
 __read_extent_tree_block(const char *function, unsigned int line,
-			 struct inode *inode, ext4_fsblk_t pblk, int depth,
-			 int flags)
+			 struct inode *inode, struct ext4_extent_idx *idx,
+			 int depth, int flags)
 {
 	struct buffer_head		*bh;
 	int				err;
 	gfp_t				gfp_flags = __GFP_MOVABLE | GFP_NOFS;
+	ext4_fsblk_t			pblk;
 
 	if (flags & EXT4_EX_NOFAIL)
 		gfp_flags |= __GFP_NOFAIL;
 
+	pblk = ext4_idx_pblock(idx);
 	bh = sb_getblk_gfp(inode->i_sb, pblk, gfp_flags);
 	if (unlikely(!bh))
 		return ERR_PTR(-ENOMEM);
@@ -508,8 +551,8 @@
 	}
 	if (buffer_verified(bh) && !(flags & EXT4_EX_FORCE_CACHE))
 		return bh;
-	err = __ext4_ext_check(function, line, inode,
-			       ext_block_hdr(bh), depth, pblk);
+	err = __ext4_ext_check(function, line, inode, ext_block_hdr(bh),
+			       depth, pblk, le32_to_cpu(idx->ei_block));
 	if (err)
 		goto errout;
 	set_buffer_verified(bh);
@@ -527,8 +570,8 @@
 
 }
 
-#define read_extent_tree_block(inode, pblk, depth, flags)		\
-	__read_extent_tree_block(__func__, __LINE__, (inode), (pblk),   \
+#define read_extent_tree_block(inode, idx, depth, flags)		\
+	__read_extent_tree_block(__func__, __LINE__, (inode), (idx),	\
 				 (depth), (flags))
 
 /*
@@ -578,8 +621,7 @@
 			i--;
 			continue;
 		}
-		bh = read_extent_tree_block(inode,
-					    ext4_idx_pblock(path[i].p_idx++),
+		bh = read_extent_tree_block(inode, path[i].p_idx++,
 					    depth - i - 1,
 					    EXT4_EX_FORCE_CACHE);
 		if (IS_ERR(bh)) {
@@ -884,8 +926,7 @@
 		path[ppos].p_depth = i;
 		path[ppos].p_ext = NULL;
 
-		bh = read_extent_tree_block(inode, path[ppos].p_block, --i,
-					    flags);
+		bh = read_extent_tree_block(inode, path[ppos].p_idx, --i, flags);
 		if (IS_ERR(bh)) {
 			ret = PTR_ERR(bh);
 			goto err;
@@ -909,6 +950,8 @@
 
 	ext4_ext_show_path(inode, path);
 
+	if (orig_path)
+		*orig_path = path;
 	return path;
 
 err:
@@ -963,6 +1006,11 @@
 		ix = curp->p_idx;
 	}
 
+	if (unlikely(ix > EXT_MAX_INDEX(curp->p_hdr))) {
+		EXT4_ERROR_INODE(inode, "ix > EXT_MAX_INDEX!");
+		return -EFSCORRUPTED;
+	}
+
 	len = EXT_LAST_INDEX(curp->p_hdr) - ix + 1;
 	BUG_ON(len < 0);
 	if (len > 0) {
@@ -972,11 +1020,6 @@
 		memmove(ix + 1, ix, len * sizeof(struct ext4_extent_idx));
 	}
 
-	if (unlikely(ix > EXT_MAX_INDEX(curp->p_hdr))) {
-		EXT4_ERROR_INODE(inode, "ix > EXT_MAX_INDEX!");
-		return -EFSCORRUPTED;
-	}
-
 	ix->ei_block = cpu_to_le32(logical);
 	ext4_idx_store_pblock(ix, ptr);
 	le16_add_cpu(&curp->p_hdr->eh_entries, 1);
@@ -1494,7 +1537,6 @@
 	struct ext4_extent_header *eh;
 	struct ext4_extent_idx *ix;
 	struct ext4_extent *ex;
-	ext4_fsblk_t block;
 	int depth;	/* Note, NOT eh_depth; depth from top of tree */
 	int ee_len;
 
@@ -1561,20 +1603,17 @@
 	 * follow it and find the closest allocated
 	 * block to the right */
 	ix++;
-	block = ext4_idx_pblock(ix);
 	while (++depth < path->p_depth) {
 		/* subtract from p_depth to get proper eh_depth */
-		bh = read_extent_tree_block(inode, block,
-					    path->p_depth - depth, 0);
+		bh = read_extent_tree_block(inode, ix, path->p_depth - depth, 0);
 		if (IS_ERR(bh))
 			return PTR_ERR(bh);
 		eh = ext_block_hdr(bh);
 		ix = EXT_FIRST_INDEX(eh);
-		block = ext4_idx_pblock(ix);
 		put_bh(bh);
 	}
 
-	bh = read_extent_tree_block(inode, block, path->p_depth - depth, 0);
+	bh = read_extent_tree_block(inode, ix, path->p_depth - depth, 0);
 	if (IS_ERR(bh))
 		return PTR_ERR(bh);
 	eh = ext_block_hdr(bh);
@@ -1835,6 +1874,7 @@
 	path[0].p_hdr->eh_max = cpu_to_le16(max_root);
 
 	brelse(path[1].p_bh);
+	path[1].p_bh = NULL;
 	ext4_free_blocks(handle, inode, NULL, blk, 1,
 			 EXT4_FREE_BLOCKS_METADATA | EXT4_FREE_BLOCKS_FORGET);
 }
@@ -2063,6 +2103,7 @@
 				       ppath, newext);
 	if (err)
 		goto cleanup;
+	path = *ppath;
 	depth = ext_depth(inode);
 	eh = path[depth].p_hdr;
 
@@ -2190,7 +2231,7 @@
 
 
 /*
- * ext4_ext_determine_hole - determine hole around given block
+ * ext4_ext_find_hole - find hole around given block according to the given path
  * @inode:	inode we lookup in
  * @path:	path in extent tree to @lblk
  * @lblk:	pointer to logical block around which we want to determine hole
@@ -2202,9 +2243,9 @@
  * The function returns the length of a hole starting at @lblk. We update @lblk
  * to the beginning of the hole if we managed to find it.
  */
-static ext4_lblk_t ext4_ext_determine_hole(struct inode *inode,
-					   struct ext4_ext_path *path,
-					   ext4_lblk_t *lblk)
+static ext4_lblk_t ext4_ext_find_hole(struct inode *inode,
+				      struct ext4_ext_path *path,
+				      ext4_lblk_t *lblk)
 {
 	int depth = ext_depth(inode);
 	struct ext4_extent *ex;
@@ -2232,30 +2273,6 @@
 }
 
 /*
- * ext4_ext_put_gap_in_cache:
- * calculate boundaries of the gap that the requested block fits into
- * and cache this gap
- */
-static void
-ext4_ext_put_gap_in_cache(struct inode *inode, ext4_lblk_t hole_start,
-			  ext4_lblk_t hole_len)
-{
-	struct extent_status es;
-
-	ext4_es_find_extent_range(inode, &ext4_es_is_delayed, hole_start,
-				  hole_start + hole_len - 1, &es);
-	if (es.es_len) {
-		/* There's delayed extent containing lblock? */
-		if (es.es_lblk <= hole_start)
-			return;
-		hole_len = min(es.es_lblk - hole_start, hole_len);
-	}
-	ext_debug(inode, " -> %u:%u\n", hole_start, hole_len);
-	ext4_es_insert_extent(inode, hole_start, hole_len, ~0,
-			      EXTENT_STATUS_HOLE);
-}
-
-/*
  * ext4_ext_rm_idx:
  * removes index from the index block.
  */
@@ -2953,9 +2970,9 @@
 			ext_debug(inode, "move to level %d (block %llu)\n",
 				  i + 1, ext4_idx_pblock(path[i].p_idx));
 			memset(path + i + 1, 0, sizeof(*path));
-			bh = read_extent_tree_block(inode,
-				ext4_idx_pblock(path[i].p_idx), depth - i - 1,
-				EXT4_EX_NOCACHE);
+			bh = read_extent_tree_block(inode, path[i].p_idx,
+						    depth - i - 1,
+						    EXT4_EX_NOCACHE);
 			if (IS_ERR(bh)) {
 				/* should we reset i_size? */
 				err = PTR_ERR(bh);
@@ -3099,8 +3116,9 @@
 	if (ee_len == 0)
 		return 0;
 
-	return ext4_es_insert_extent(inode, ee_block, ee_len, ee_pblock,
-				     EXTENT_STATUS_WRITTEN);
+	ext4_es_insert_extent(inode, ee_block, ee_len, ee_pblock,
+			      EXTENT_STATUS_WRITTEN);
+	return 0;
 }
 
 /* FIXME!! we need to try to merge to left or right after zero-out  */
@@ -3214,9 +3232,27 @@
 		ext4_ext_mark_unwritten(ex2);
 
 	err = ext4_ext_insert_extent(handle, inode, ppath, &newex, flags);
-	if (err != -ENOSPC && err != -EDQUOT)
+	if (err != -ENOSPC && err != -EDQUOT && err != -ENOMEM)
 		goto out;
 
+	/*
+	 * Update path is required because previous ext4_ext_insert_extent()
+	 * may have freed or reallocated the path. Using EXT4_EX_NOFAIL
+	 * guarantees that ext4_find_extent() will not return -ENOMEM,
+	 * otherwise -ENOMEM will cause a retry in do_writepages(), and a
+	 * WARN_ON may be triggered in ext4_da_update_reserve_space() due to
+	 * an incorrect ee_len causing the i_reserved_data_blocks exception.
+	 */
+	path = ext4_find_extent(inode, ee_block, ppath,
+				flags | EXT4_EX_NOFAIL);
+	if (IS_ERR(path)) {
+		EXT4_ERROR_INODE(inode, "Failed split extent on %u, err %ld",
+				 split, PTR_ERR(path));
+		return PTR_ERR(path);
+	}
+	depth = ext_depth(inode);
+	ex = path[depth].p_ext;
+
 	if (EXT4_EXT_MAY_ZEROOUT & split_flag) {
 		if (split_flag & (EXT4_EXT_DATA_VALID1|EXT4_EXT_DATA_VALID2)) {
 			if (split_flag & EXT4_EXT_DATA_VALID1) {
@@ -3269,12 +3305,12 @@
 	ext4_ext_dirty(handle, inode, path + path->p_depth);
 	return err;
 out:
-	ext4_ext_show_leaf(inode, path);
+	ext4_ext_show_leaf(inode, *ppath);
 	return err;
 }
 
 /*
- * ext4_split_extents() splits an extent and mark extent which is covered
+ * ext4_split_extent() splits an extent and mark extent which is covered
  * by @map as split_flags indicates
  *
  * It may result in splitting the extent into multiple extents (up to three)
@@ -3351,7 +3387,7 @@
 			goto out;
 	}
 
-	ext4_ext_show_leaf(inode, path);
+	ext4_ext_show_leaf(inode, *ppath);
 out:
 	return err ? err : allocated;
 }
@@ -3390,9 +3426,10 @@
 	struct ext4_extent *ex, *abut_ex;
 	ext4_lblk_t ee_block, eof_block;
 	unsigned int ee_len, depth, map_len = map->m_len;
-	int allocated = 0, max_zeroout = 0;
 	int err = 0;
 	int split_flag = EXT4_EXT_DATA_VALID2;
+	int allocated = 0;
+	unsigned int max_zeroout = 0;
 
 	ext_debug(inode, "logical block %llu, max_blocks %u\n",
 		  (unsigned long long)map->m_lblk, map_len);
@@ -3816,14 +3853,13 @@
 			struct ext4_ext_path **ppath, int flags,
 			unsigned int allocated, ext4_fsblk_t newblock)
 {
-	struct ext4_ext_path __maybe_unused *path = *ppath;
 	int ret = 0;
 	int err = 0;
 
 	ext_debug(inode, "logical block %llu, max_blocks %u, flags 0x%x, allocated %u\n",
 		  (unsigned long long)map->m_lblk, map->m_len, flags,
 		  allocated);
-	ext4_ext_show_leaf(inode, path);
+	ext4_ext_show_leaf(inode, *ppath);
 
 	/*
 	 * When writing into unwritten space, we should not fail to
@@ -3920,7 +3956,7 @@
 	if (allocated > map->m_len)
 		allocated = map->m_len;
 	map->m_len = allocated;
-	ext4_ext_show_leaf(inode, path);
+	ext4_ext_show_leaf(inode, *ppath);
 out2:
 	return err ? err : allocated;
 }
@@ -4027,6 +4063,69 @@
 	return 0;
 }
 
+/*
+ * Determine hole length around the given logical block, first try to
+ * locate and expand the hole from the given @path, and then adjust it
+ * if it's partially or completely converted to delayed extents, insert
+ * it into the extent cache tree if it's indeed a hole, finally return
+ * the length of the determined extent.
+ */
+static ext4_lblk_t ext4_ext_determine_insert_hole(struct inode *inode,
+						  struct ext4_ext_path *path,
+						  ext4_lblk_t lblk)
+{
+	ext4_lblk_t hole_start, len;
+	struct extent_status es;
+
+	hole_start = lblk;
+	len = ext4_ext_find_hole(inode, path, &hole_start);
+again:
+	ext4_es_find_extent_range(inode, &ext4_es_is_delayed, hole_start,
+				  hole_start + len - 1, &es);
+	if (!es.es_len)
+		goto insert_hole;
+
+	/*
+	 * There's a delalloc extent in the hole, handle it if the delalloc
+	 * extent is in front of, behind and straddle the queried range.
+	 */
+	if (lblk >= es.es_lblk + es.es_len) {
+		/*
+		 * The delalloc extent is in front of the queried range,
+		 * find again from the queried start block.
+		 */
+		len -= lblk - hole_start;
+		hole_start = lblk;
+		goto again;
+	} else if (in_range(lblk, es.es_lblk, es.es_len)) {
+		/*
+		 * The delalloc extent containing lblk, it must have been
+		 * added after ext4_map_blocks() checked the extent status
+		 * tree, adjust the length to the delalloc extent's after
+		 * lblk.
+		 */
+		len = es.es_lblk + es.es_len - lblk;
+		return len;
+	} else {
+		/*
+		 * The delalloc extent is partially or completely behind
+		 * the queried range, update hole length until the
+		 * beginning of the delalloc extent.
+		 */
+		len = min(es.es_lblk - hole_start, len);
+	}
+
+insert_hole:
+	/* Put just found gap into cache to speed up subsequent requests */
+	ext_debug(inode, " -> %u:%u\n", hole_start, len);
+	ext4_es_insert_extent(inode, hole_start, len, ~0, EXTENT_STATUS_HOLE);
+
+	/* Update hole_len to reflect hole size after lblk */
+	if (hole_start != lblk)
+		len -= lblk - hole_start;
+
+	return len;
+}
 
 /*
  * Block allocation/map/preallocation routine for extents based files
@@ -4144,22 +4243,12 @@
 	 * we couldn't try to create block if create flag is zero
 	 */
 	if ((flags & EXT4_GET_BLOCKS_CREATE) == 0) {
-		ext4_lblk_t hole_start, hole_len;
+		ext4_lblk_t len;
 
-		hole_start = map->m_lblk;
-		hole_len = ext4_ext_determine_hole(inode, path, &hole_start);
-		/*
-		 * put just found gap into cache to speed up
-		 * subsequent requests
-		 */
-		ext4_ext_put_gap_in_cache(inode, hole_start, hole_len);
+		len = ext4_ext_determine_insert_hole(inode, path, map->m_lblk);
 
-		/* Update hole_len to reflect hole size after map->m_lblk */
-		if (hole_start != map->m_lblk)
-			hole_len -= map->m_lblk - hole_start;
 		map->m_pblk = 0;
-		map->m_len = min_t(unsigned int, map->m_len, hole_len);
-
+		map->m_len = min_t(unsigned int, map->m_len, len);
 		goto out;
 	}
 
@@ -4471,9 +4560,9 @@
 	return ret > 0 ? ret2 : ret;
 }
 
-static int ext4_collapse_range(struct inode *inode, loff_t offset, loff_t len);
+static int ext4_collapse_range(struct file *file, loff_t offset, loff_t len);
 
-static int ext4_insert_range(struct inode *inode, loff_t offset, loff_t len);
+static int ext4_insert_range(struct file *file, loff_t offset, loff_t len);
 
 static long ext4_zero_range(struct file *file, loff_t offset,
 			    loff_t len, int mode)
@@ -4545,6 +4634,10 @@
 	/* Wait all existing dio workers, newcomers will block on i_mutex */
 	inode_dio_wait(inode);
 
+	ret = file_modified(file);
+	if (ret)
+		goto out_mutex;
+
 	/* Preallocate the range including the unaligned edges */
 	if (partial_begin || partial_end) {
 		ret = ext4_alloc_file_blocks(file,
@@ -4612,8 +4705,6 @@
 	ret = ext4_mark_inode_dirty(handle, inode);
 	if (unlikely(ret))
 		goto out_handle;
-	ext4_fc_track_range(handle, inode, offset >> inode->i_sb->s_blocksize_bits,
-			(offset + len - 1) >> inode->i_sb->s_blocksize_bits);
 	/* Zero out partial block at the edges of the range */
 	ret = ext4_zero_partial_blocks(handle, inode, offset, len);
 	if (ret >= 0)
@@ -4662,24 +4753,24 @@
 		     FALLOC_FL_INSERT_RANGE))
 		return -EOPNOTSUPP;
 
-	ext4_fc_start_update(inode);
+	inode_lock(inode);
+	ret = ext4_convert_inline_data(inode);
+	inode_unlock(inode);
+	if (ret)
+		goto exit;
 
 	if (mode & FALLOC_FL_PUNCH_HOLE) {
-		ret = ext4_punch_hole(inode, offset, len);
+		ret = ext4_punch_hole(file, offset, len);
 		goto exit;
 	}
 
-	ret = ext4_convert_inline_data(inode);
-	if (ret)
-		goto exit;
-
 	if (mode & FALLOC_FL_COLLAPSE_RANGE) {
-		ret = ext4_collapse_range(inode, offset, len);
+		ret = ext4_collapse_range(file, offset, len);
 		goto exit;
 	}
 
 	if (mode & FALLOC_FL_INSERT_RANGE) {
-		ret = ext4_insert_range(inode, offset, len);
+		ret = ext4_insert_range(file, offset, len);
 		goto exit;
 	}
 
@@ -4715,6 +4806,10 @@
 	/* Wait all existing dio workers, newcomers will block on i_mutex */
 	inode_dio_wait(inode);
 
+	ret = file_modified(file);
+	if (ret)
+		goto out;
+
 	ret = ext4_alloc_file_blocks(file, lblk, max_blocks, new_size, flags);
 	if (ret)
 		goto out;
@@ -4727,7 +4822,6 @@
 	inode_unlock(inode);
 	trace_ext4_fallocate_exit(inode, offset, max_blocks, ret);
 exit:
-	ext4_fc_stop_update(inode);
 	return ret;
 }
 
@@ -4978,36 +5072,6 @@
 }
 
 /*
- * ext4_access_path:
- * Function to access the path buffer for marking it dirty.
- * It also checks if there are sufficient credits left in the journal handle
- * to update path.
- */
-static int
-ext4_access_path(handle_t *handle, struct inode *inode,
-		struct ext4_ext_path *path)
-{
-	int credits, err;
-
-	if (!ext4_handle_valid(handle))
-		return 0;
-
-	/*
-	 * Check if need to extend journal credits
-	 * 3 for leaf, sb, and inode plus 2 (bmap and group
-	 * descriptor) for each block group; assume two block
-	 * groups
-	 */
-	credits = ext4_writepage_trans_blocks(inode);
-	err = ext4_datasem_ensure_credits(handle, inode, 7, credits, 0);
-	if (err < 0)
-		return err;
-
-	err = ext4_ext_get_access(handle, inode, path);
-	return err;
-}
-
-/*
  * ext4_ext_shift_path_extents:
  * Shift the extents of a path structure lying between path[depth].p_ext
  * and EXT_LAST_EXTENT(path[depth].p_hdr), by @shift blocks. @SHIFT tells
@@ -5021,6 +5085,7 @@
 	int depth, err = 0;
 	struct ext4_extent *ex_start, *ex_last;
 	bool update = false;
+	int credits, restart_credits;
 	depth = path->p_depth;
 
 	while (depth >= 0) {
@@ -5030,13 +5095,26 @@
 				return -EFSCORRUPTED;
 
 			ex_last = EXT_LAST_EXTENT(path[depth].p_hdr);
+			/* leaf + sb + inode */
+			credits = 3;
+			if (ex_start == EXT_FIRST_EXTENT(path[depth].p_hdr)) {
+				update = true;
+				/* extent tree + sb + inode */
+				credits = depth + 2;
+			}
 
-			err = ext4_access_path(handle, inode, path + depth);
-			if (err)
+			restart_credits = ext4_writepage_trans_blocks(inode);
+			err = ext4_datasem_ensure_credits(handle, inode, credits,
+					restart_credits, 0);
+			if (err) {
+				if (err > 0)
+					err = -EAGAIN;
 				goto out;
+			}
 
-			if (ex_start == EXT_FIRST_EXTENT(path[depth].p_hdr))
-				update = true;
+			err = ext4_ext_get_access(handle, inode, path + depth);
+			if (err)
+				goto out;
 
 			while (ex_start <= ex_last) {
 				if (SHIFT == SHIFT_LEFT) {
@@ -5067,7 +5145,7 @@
 		}
 
 		/* Update index too */
-		err = ext4_access_path(handle, inode, path + depth);
+		err = ext4_ext_get_access(handle, inode, path + depth);
 		if (err)
 			goto out;
 
@@ -5106,6 +5184,7 @@
 	int ret = 0, depth;
 	struct ext4_extent *extent;
 	ext4_lblk_t stop, *iterator, ex_start, ex_end;
+	ext4_lblk_t tmp = EXT_MAX_BLOCKS;
 
 	/* Let path point to the last extent */
 	path = ext4_find_extent(inode, EXT_MAX_BLOCKS - 1, NULL,
@@ -5159,11 +5238,16 @@
 	 * till we reach stop. In case of right shift, iterator points to stop
 	 * and it is decreased till we reach start.
 	 */
+again:
+	ret = 0;
 	if (SHIFT == SHIFT_LEFT)
 		iterator = &start;
 	else
 		iterator = &stop;
 
+	if (tmp != EXT_MAX_BLOCKS)
+		*iterator = tmp;
+
 	/*
 	 * Its safe to start updating extents.  Start and stop are unsigned, so
 	 * in case of right shift if extent with 0 block is reached, iterator
@@ -5192,24 +5276,35 @@
 			}
 		}
 
+		tmp = *iterator;
 		if (SHIFT == SHIFT_LEFT) {
 			extent = EXT_LAST_EXTENT(path[depth].p_hdr);
 			*iterator = le32_to_cpu(extent->ee_block) +
 					ext4_ext_get_actual_len(extent);
 		} else {
 			extent = EXT_FIRST_EXTENT(path[depth].p_hdr);
-			if (le32_to_cpu(extent->ee_block) > 0)
+			if (le32_to_cpu(extent->ee_block) > start)
 				*iterator = le32_to_cpu(extent->ee_block) - 1;
-			else
-				/* Beginning is reached, end of the loop */
+			else if (le32_to_cpu(extent->ee_block) == start)
 				iterator = NULL;
-			/* Update path extent in case we need to stop */
-			while (le32_to_cpu(extent->ee_block) < start)
+			else {
+				extent = EXT_LAST_EXTENT(path[depth].p_hdr);
+				while (le32_to_cpu(extent->ee_block) >= start)
+					extent--;
+
+				if (extent == EXT_LAST_EXTENT(path[depth].p_hdr))
+					break;
+
 				extent++;
+				iterator = NULL;
+			}
 			path[depth].p_ext = extent;
 		}
 		ret = ext4_ext_shift_path_extents(path, shift, inode,
 				handle, SHIFT);
+		/* iterator can be NULL which means we should break */
+		if (ret == -EAGAIN)
+			goto again;
 		if (ret)
 			break;
 	}
@@ -5224,8 +5319,9 @@
  * This implements the fallocate's collapse range functionality for ext4
  * Returns: 0 and non-zero on error.
  */
-static int ext4_collapse_range(struct inode *inode, loff_t offset, loff_t len)
+static int ext4_collapse_range(struct file *file, loff_t offset, loff_t len)
 {
+	struct inode *inode = file_inode(file);
 	struct super_block *sb = inode->i_sb;
 	struct address_space *mapping = inode->i_mapping;
 	ext4_lblk_t punch_start, punch_stop;
@@ -5277,6 +5373,10 @@
 	/* Wait for existing dio to complete */
 	inode_dio_wait(inode);
 
+	ret = file_modified(file);
+	if (ret)
+		goto out_mutex;
+
 	/*
 	 * Prevent page faults from reinstantiating pages we have released from
 	 * page cache.
@@ -5316,7 +5416,7 @@
 		ret = PTR_ERR(handle);
 		goto out_mmap;
 	}
-	ext4_fc_start_ineligible(sb, EXT4_FC_REASON_FALLOC_RANGE);
+	ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_FALLOC_RANGE, handle);
 
 	down_write(&EXT4_I(inode)->i_data_sem);
 	ext4_discard_preallocations(inode, 0);
@@ -5355,7 +5455,6 @@
 
 out_stop:
 	ext4_journal_stop(handle);
-	ext4_fc_stop_ineligible(sb);
 out_mmap:
 	filemap_invalidate_unlock(mapping);
 out_mutex:
@@ -5371,8 +5470,9 @@
  * by len bytes.
  * Returns 0 on success, error otherwise.
  */
-static int ext4_insert_range(struct inode *inode, loff_t offset, loff_t len)
+static int ext4_insert_range(struct file *file, loff_t offset, loff_t len)
 {
+	struct inode *inode = file_inode(file);
 	struct super_block *sb = inode->i_sb;
 	struct address_space *mapping = inode->i_mapping;
 	handle_t *handle;
@@ -5429,6 +5529,10 @@
 	/* Wait for existing dio to complete */
 	inode_dio_wait(inode);
 
+	ret = file_modified(file);
+	if (ret)
+		goto out_mutex;
+
 	/*
 	 * Prevent page faults from reinstantiating pages we have released from
 	 * page cache.
@@ -5457,7 +5561,7 @@
 		ret = PTR_ERR(handle);
 		goto out_mmap;
 	}
-	ext4_fc_start_ineligible(sb, EXT4_FC_REASON_FALLOC_RANGE);
+	ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_FALLOC_RANGE, handle);
 
 	/* Expand file to avoid data loss if there is error while shifting */
 	inode->i_size += len;
@@ -5473,6 +5577,7 @@
 	path = ext4_find_extent(inode, offset_lblk, NULL, 0);
 	if (IS_ERR(path)) {
 		up_write(&EXT4_I(inode)->i_data_sem);
+		ret = PTR_ERR(path);
 		goto out_stop;
 	}
 
@@ -5532,7 +5637,6 @@
 
 out_stop:
 	ext4_journal_stop(handle);
-	ext4_fc_stop_ineligible(sb);
 out_mmap:
 	filemap_invalidate_unlock(mapping);
 out_mutex:
@@ -5756,6 +5860,15 @@
 	struct ext4_extent *extent;
 	ext4_lblk_t first_lblk, first_lclu, last_lclu;
 
+	/*
+	 * if data can be stored inline, the logical cluster isn't
+	 * mapped - no physical clusters have been allocated, and the
+	 * file has no extents
+	 */
+	if (ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA) ||
+	    ext4_has_inline_data(inode))
+		return 0;
+
 	/* search for the extent closest to the first block in the cluster */
 	path = ext4_find_extent(inode, EXT4_C2B(sbi, lclu), NULL, 0);
 	if (IS_ERR(path)) {
@@ -5825,7 +5938,7 @@
 int ext4_ext_replay_update_ex(struct inode *inode, ext4_lblk_t start,
 			      int len, int unwritten, ext4_fsblk_t pblk)
 {
-	struct ext4_ext_path *path = NULL, *ppath;
+	struct ext4_ext_path *path;
 	struct ext4_extent *ex;
 	int ret;
 
@@ -5841,30 +5954,29 @@
 	if (le32_to_cpu(ex->ee_block) != start ||
 		ext4_ext_get_actual_len(ex) != len) {
 		/* We need to split this extent to match our extent first */
-		ppath = path;
 		down_write(&EXT4_I(inode)->i_data_sem);
-		ret = ext4_force_split_extent_at(NULL, inode, &ppath, start, 1);
+		ret = ext4_force_split_extent_at(NULL, inode, &path, start, 1);
 		up_write(&EXT4_I(inode)->i_data_sem);
 		if (ret)
 			goto out;
-		kfree(path);
-		path = ext4_find_extent(inode, start, NULL, 0);
+
+		path = ext4_find_extent(inode, start, &path, 0);
 		if (IS_ERR(path))
-			return -1;
-		ppath = path;
+			return PTR_ERR(path);
 		ex = path[path->p_depth].p_ext;
 		WARN_ON(le32_to_cpu(ex->ee_block) != start);
+
 		if (ext4_ext_get_actual_len(ex) != len) {
 			down_write(&EXT4_I(inode)->i_data_sem);
-			ret = ext4_force_split_extent_at(NULL, inode, &ppath,
+			ret = ext4_force_split_extent_at(NULL, inode, &path,
 							 start + len, 1);
 			up_write(&EXT4_I(inode)->i_data_sem);
 			if (ret)
 				goto out;
-			kfree(path);
-			path = ext4_find_extent(inode, start, NULL, 0);
+
+			path = ext4_find_extent(inode, start, &path, 0);
 			if (IS_ERR(path))
-				return -EINVAL;
+				return PTR_ERR(path);
 			ex = path[path->p_depth].p_ext;
 		}
 	}
@@ -6072,11 +6184,15 @@
 
 					ext4_mb_mark_bb(inode->i_sb,
 							path[j].p_block, 1, 0);
+					ext4_fc_record_regions(inode->i_sb, inode->i_ino,
+							0, path[j].p_block, 1, 1);
 				}
 				ext4_ext_drop_refs(path);
 				kfree(path);
 			}
 			ext4_mb_mark_bb(inode->i_sb, map.m_pblk, map.m_len, 0);
+			ext4_fc_record_regions(inode->i_sb, inode->i_ino,
+					map.m_lblk, map.m_pblk, map.m_len, 1);
 		}
 		cur = cur + map.m_len;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/extents_status.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/extents_status.c
@@ -144,14 +144,17 @@
 static struct kmem_cache *ext4_es_cachep;
 static struct kmem_cache *ext4_pending_cachep;
 
-static int __es_insert_extent(struct inode *inode, struct extent_status *newes);
+static int __es_insert_extent(struct inode *inode, struct extent_status *newes,
+			      struct extent_status *prealloc);
 static int __es_remove_extent(struct inode *inode, ext4_lblk_t lblk,
-			      ext4_lblk_t end, int *reserved);
+			      ext4_lblk_t end, int *reserved,
+			      struct extent_status *prealloc);
 static int es_reclaim_extents(struct ext4_inode_info *ei, int *nr_to_scan);
 static int __es_shrink(struct ext4_sb_info *sbi, int nr_to_scan,
 		       struct ext4_inode_info *locked_ei);
-static void __revise_pending(struct inode *inode, ext4_lblk_t lblk,
-			     ext4_lblk_t len);
+static int __revise_pending(struct inode *inode, ext4_lblk_t lblk,
+			    ext4_lblk_t len,
+			    struct pending_reservation **prealloc);
 
 int __init ext4_init_es(void)
 {
@@ -269,14 +272,12 @@
 
 	/* see if the extent has been cached */
 	es->es_lblk = es->es_len = es->es_pblk = 0;
-	if (tree->cache_es) {
-		es1 = tree->cache_es;
-		if (in_range(lblk, es1->es_lblk, es1->es_len)) {
-			es_debug("%u cached by [%u/%u) %llu %x\n",
-				 lblk, es1->es_lblk, es1->es_len,
-				 ext4_es_pblock(es1), ext4_es_status(es1));
-			goto out;
-		}
+	es1 = READ_ONCE(tree->cache_es);
+	if (es1 && in_range(lblk, es1->es_lblk, es1->es_len)) {
+		es_debug("%u cached by [%u/%u) %llu %x\n",
+			 lblk, es1->es_lblk, es1->es_len,
+			 ext4_es_pblock(es1), ext4_es_status(es1));
+		goto out;
 	}
 
 	es1 = __es_tree_search(&tree->root, lblk);
@@ -295,7 +296,7 @@
 	}
 
 	if (es1 && matching_fn(es1)) {
-		tree->cache_es = es1;
+		WRITE_ONCE(tree->cache_es, es1);
 		es->es_lblk = es1->es_lblk;
 		es->es_len = es1->es_len;
 		es->es_pblk = es1->es_pblk;
@@ -311,6 +312,8 @@
 			       ext4_lblk_t lblk, ext4_lblk_t end,
 			       struct extent_status *es)
 {
+	es->es_lblk = es->es_len = es->es_pblk = 0;
+
 	if (EXT4_SB(inode->i_sb)->s_mount_state & EXT4_FC_REPLAY)
 		return;
 
@@ -450,22 +453,49 @@
 	spin_unlock(&sbi->s_es_lock);
 }
 
-static struct extent_status *
-ext4_es_alloc_extent(struct inode *inode, ext4_lblk_t lblk, ext4_lblk_t len,
-		     ext4_fsblk_t pblk)
+static inline struct pending_reservation *__alloc_pending(bool nofail)
+{
+	if (!nofail)
+		return kmem_cache_alloc(ext4_pending_cachep, GFP_ATOMIC);
+
+	return kmem_cache_zalloc(ext4_pending_cachep, GFP_KERNEL | __GFP_NOFAIL);
+}
+
+static inline void __free_pending(struct pending_reservation *pr)
+{
+	kmem_cache_free(ext4_pending_cachep, pr);
+}
+
+/*
+ * Returns true if we cannot fail to allocate memory for this extent_status
+ * entry and cannot reclaim it until its status changes.
+ */
+static inline bool ext4_es_must_keep(struct extent_status *es)
+{
+	/* fiemap, bigalloc, and seek_data/hole need to use it. */
+	if (ext4_es_is_delayed(es))
+		return true;
+
+	return false;
+}
+
+static inline struct extent_status *__es_alloc_extent(bool nofail)
+{
+	if (!nofail)
+		return kmem_cache_alloc(ext4_es_cachep, GFP_ATOMIC);
+
+	return kmem_cache_zalloc(ext4_es_cachep, GFP_KERNEL | __GFP_NOFAIL);
+}
+
+static void ext4_es_init_extent(struct inode *inode, struct extent_status *es,
+		ext4_lblk_t lblk, ext4_lblk_t len, ext4_fsblk_t pblk)
 {
-	struct extent_status *es;
-	es = kmem_cache_alloc(ext4_es_cachep, GFP_ATOMIC);
-	if (es == NULL)
-		return NULL;
 	es->es_lblk = lblk;
 	es->es_len = len;
 	es->es_pblk = pblk;
 
-	/*
-	 * We don't count delayed extent because we never try to reclaim them
-	 */
-	if (!ext4_es_is_delayed(es)) {
+	/* We never try to reclaim a must kept extent, so we don't count it. */
+	if (!ext4_es_must_keep(es)) {
 		if (!EXT4_I(inode)->i_es_shk_nr++)
 			ext4_es_list_add(inode);
 		percpu_counter_inc(&EXT4_SB(inode->i_sb)->
@@ -474,8 +504,11 @@
 
 	EXT4_I(inode)->i_es_all_nr++;
 	percpu_counter_inc(&EXT4_SB(inode->i_sb)->s_es_stats.es_stats_all_cnt);
+}
 
-	return es;
+static inline void __es_free_extent(struct extent_status *es)
+{
+	kmem_cache_free(ext4_es_cachep, es);
 }
 
 static void ext4_es_free_extent(struct inode *inode, struct extent_status *es)
@@ -483,8 +516,8 @@
 	EXT4_I(inode)->i_es_all_nr--;
 	percpu_counter_dec(&EXT4_SB(inode->i_sb)->s_es_stats.es_stats_all_cnt);
 
-	/* Decrease the shrink counter when this es is not delayed */
-	if (!ext4_es_is_delayed(es)) {
+	/* Decrease the shrink counter when we can reclaim the extent. */
+	if (!ext4_es_must_keep(es)) {
 		BUG_ON(EXT4_I(inode)->i_es_shk_nr == 0);
 		if (!--EXT4_I(inode)->i_es_shk_nr)
 			ext4_es_list_del(inode);
@@ -492,7 +525,7 @@
 					s_es_stats.es_stats_shk_cnt);
 	}
 
-	kmem_cache_free(ext4_es_cachep, es);
+	__es_free_extent(es);
 }
 
 /*
@@ -754,7 +787,8 @@
 }
 #endif
 
-static int __es_insert_extent(struct inode *inode, struct extent_status *newes)
+static int __es_insert_extent(struct inode *inode, struct extent_status *newes,
+			      struct extent_status *prealloc)
 {
 	struct ext4_es_tree *tree = &EXT4_I(inode)->i_es_tree;
 	struct rb_node **p = &tree->root.rb_node;
@@ -794,10 +828,15 @@
 		}
 	}
 
-	es = ext4_es_alloc_extent(inode, newes->es_lblk, newes->es_len,
-				  newes->es_pblk);
+	if (prealloc)
+		es = prealloc;
+	else
+		es = __es_alloc_extent(false);
 	if (!es)
 		return -ENOMEM;
+	ext4_es_init_extent(inode, es, newes->es_lblk, newes->es_len,
+			    newes->es_pblk);
+
 	rb_link_node(&es->rb_node, parent, p);
 	rb_insert_color(&es->rb_node, &tree->root);
 
@@ -809,26 +848,28 @@
 /*
  * ext4_es_insert_extent() adds information to an inode's extent
  * status tree.
- *
- * Return 0 on success, error code on failure.
  */
-int ext4_es_insert_extent(struct inode *inode, ext4_lblk_t lblk,
-			  ext4_lblk_t len, ext4_fsblk_t pblk,
-			  unsigned int status)
+void ext4_es_insert_extent(struct inode *inode, ext4_lblk_t lblk,
+			   ext4_lblk_t len, ext4_fsblk_t pblk,
+			   unsigned int status)
 {
 	struct extent_status newes;
 	ext4_lblk_t end = lblk + len - 1;
-	int err = 0;
+	int err1 = 0, err2 = 0, err3 = 0;
 	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+	struct extent_status *es1 = NULL;
+	struct extent_status *es2 = NULL;
+	struct pending_reservation *pr = NULL;
+	bool revise_pending = false;
 
 	if (EXT4_SB(inode->i_sb)->s_mount_state & EXT4_FC_REPLAY)
-		return 0;
+		return;
 
 	es_debug("add [%u/%u) %llu %x to extent status tree of inode %lu\n",
 		 lblk, len, pblk, status, inode->i_ino);
 
 	if (!len)
-		return 0;
+		return;
 
 	BUG_ON(end < lblk);
 
@@ -847,29 +888,57 @@
 
 	ext4_es_insert_extent_check(inode, &newes);
 
+	revise_pending = sbi->s_cluster_ratio > 1 &&
+			 test_opt(inode->i_sb, DELALLOC) &&
+			 (status & (EXTENT_STATUS_WRITTEN |
+				    EXTENT_STATUS_UNWRITTEN));
+retry:
+	if (err1 && !es1)
+		es1 = __es_alloc_extent(true);
+	if ((err1 || err2) && !es2)
+		es2 = __es_alloc_extent(true);
+	if ((err1 || err2 || err3) && revise_pending && !pr)
+		pr = __alloc_pending(true);
 	write_lock(&EXT4_I(inode)->i_es_lock);
-	err = __es_remove_extent(inode, lblk, end, NULL);
-	if (err != 0)
+
+	err1 = __es_remove_extent(inode, lblk, end, NULL, es1);
+	if (err1 != 0)
 		goto error;
-retry:
-	err = __es_insert_extent(inode, &newes);
-	if (err == -ENOMEM && __es_shrink(EXT4_SB(inode->i_sb),
-					  128, EXT4_I(inode)))
-		goto retry;
-	if (err == -ENOMEM && !ext4_es_is_delayed(&newes))
-		err = 0;
+	/* Free preallocated extent if it didn't get used. */
+	if (es1) {
+		if (!es1->es_len)
+			__es_free_extent(es1);
+		es1 = NULL;
+	}
 
-	if (sbi->s_cluster_ratio > 1 && test_opt(inode->i_sb, DELALLOC) &&
-	    (status & EXTENT_STATUS_WRITTEN ||
-	     status & EXTENT_STATUS_UNWRITTEN))
-		__revise_pending(inode, lblk, len);
+	err2 = __es_insert_extent(inode, &newes, es2);
+	if (err2 == -ENOMEM && !ext4_es_must_keep(&newes))
+		err2 = 0;
+	if (err2 != 0)
+		goto error;
+	/* Free preallocated extent if it didn't get used. */
+	if (es2) {
+		if (!es2->es_len)
+			__es_free_extent(es2);
+		es2 = NULL;
+	}
 
+	if (revise_pending) {
+		err3 = __revise_pending(inode, lblk, len, &pr);
+		if (err3 != 0)
+			goto error;
+		if (pr) {
+			__free_pending(pr);
+			pr = NULL;
+		}
+	}
 error:
 	write_unlock(&EXT4_I(inode)->i_es_lock);
+	if (err1 || err2 || err3)
+		goto retry;
 
 	ext4_es_print_tree(inode);
-
-	return err;
+	return;
 }
 
 /*
@@ -902,7 +971,7 @@
 
 	es = __es_tree_search(&EXT4_I(inode)->i_es_tree.root, lblk);
 	if (!es || es->es_lblk > end)
-		__es_insert_extent(inode, &newes);
+		__es_insert_extent(inode, &newes, NULL);
 	write_unlock(&EXT4_I(inode)->i_es_lock);
 }
 
@@ -934,14 +1003,12 @@
 
 	/* find extent in cache firstly */
 	es->es_lblk = es->es_len = es->es_pblk = 0;
-	if (tree->cache_es) {
-		es1 = tree->cache_es;
-		if (in_range(lblk, es1->es_lblk, es1->es_len)) {
-			es_debug("%u cached by [%u/%u)\n",
-				 lblk, es1->es_lblk, es1->es_len);
-			found = 1;
-			goto out;
-		}
+	es1 = READ_ONCE(tree->cache_es);
+	if (es1 && in_range(lblk, es1->es_lblk, es1->es_len)) {
+		es_debug("%u cached by [%u/%u)\n",
+			 lblk, es1->es_lblk, es1->es_len);
+		found = 1;
+		goto out;
 	}
 
 	node = tree->root.rb_node;
@@ -1275,7 +1342,7 @@
 				rc->ndelonly--;
 				node = rb_next(&pr->rb_node);
 				rb_erase(&pr->rb_node, &tree->root);
-				kmem_cache_free(ext4_pending_cachep, pr);
+				__free_pending(pr);
 				if (!node)
 					break;
 				pr = rb_entry(node, struct pending_reservation,
@@ -1294,6 +1361,7 @@
  * @lblk - first block in range
  * @end - last block in range
  * @reserved - number of cluster reservations released
+ * @prealloc - pre-allocated es to avoid memory allocation failures
  *
  * If @reserved is not NULL and delayed allocation is enabled, counts
  * block/cluster reservations freed by removing range and if bigalloc
@@ -1301,7 +1369,8 @@
  * error code on failure.
  */
 static int __es_remove_extent(struct inode *inode, ext4_lblk_t lblk,
-			      ext4_lblk_t end, int *reserved)
+			      ext4_lblk_t end, int *reserved,
+			      struct extent_status *prealloc)
 {
 	struct ext4_es_tree *tree = &EXT4_I(inode)->i_es_tree;
 	struct rb_node *node;
@@ -1309,14 +1378,12 @@
 	struct extent_status orig_es;
 	ext4_lblk_t len1, len2;
 	ext4_fsblk_t block;
-	int err;
+	int err = 0;
 	bool count_reserved = true;
 	struct rsvd_count rc;
 
 	if (reserved == NULL || !test_opt(inode->i_sb, DELALLOC))
 		count_reserved = false;
-retry:
-	err = 0;
 
 	es = __es_tree_search(&tree->root, lblk);
 	if (!es)
@@ -1350,14 +1417,13 @@
 					orig_es.es_len - len2;
 			ext4_es_store_pblock_status(&newes, block,
 						    ext4_es_status(&orig_es));
-			err = __es_insert_extent(inode, &newes);
+			err = __es_insert_extent(inode, &newes, prealloc);
 			if (err) {
+				if (!ext4_es_must_keep(&newes))
+					return 0;
+
 				es->es_lblk = orig_es.es_lblk;
 				es->es_len = orig_es.es_len;
-				if ((err == -ENOMEM) &&
-				    __es_shrink(EXT4_SB(inode->i_sb),
-							128, EXT4_I(inode)))
-					goto retry;
 				goto out;
 			}
 		} else {
@@ -1370,9 +1436,9 @@
 			}
 		}
 		if (count_reserved)
-			count_rsvd(inode, lblk, orig_es.es_len - len1 - len2,
-				   &orig_es, &rc);
-		goto out;
+			count_rsvd(inode, orig_es.es_lblk + len1,
+				   orig_es.es_len - len1 - len2, &orig_es, &rc);
+		goto out_get_reserved;
 	}
 
 	if (len1 > 0) {
@@ -1414,6 +1480,7 @@
 		}
 	}
 
+out_get_reserved:
 	if (count_reserved)
 		*reserved = get_rsvd(inode, end, es, &rc);
 out:
@@ -1436,6 +1503,7 @@
 	ext4_lblk_t end;
 	int err = 0;
 	int reserved = 0;
+	struct extent_status *es = NULL;
 
 	if (EXT4_SB(inode->i_sb)->s_mount_state & EXT4_FC_REPLAY)
 		return 0;
@@ -1450,17 +1518,29 @@
 	end = lblk + len - 1;
 	BUG_ON(end < lblk);
 
+retry:
+	if (err && !es)
+		es = __es_alloc_extent(true);
 	/*
 	 * ext4_clear_inode() depends on us taking i_es_lock unconditionally
 	 * so that we are sure __es_shrink() is done with the inode before it
 	 * is reclaimed.
 	 */
 	write_lock(&EXT4_I(inode)->i_es_lock);
-	err = __es_remove_extent(inode, lblk, end, &reserved);
+	err = __es_remove_extent(inode, lblk, end, &reserved, es);
+	/* Free preallocated extent if it didn't get used. */
+	if (es) {
+		if (!es->es_len)
+			__es_free_extent(es);
+		es = NULL;
+	}
 	write_unlock(&EXT4_I(inode)->i_es_lock);
+	if (err)
+		goto retry;
+
 	ext4_es_print_tree(inode);
 	ext4_da_release_space(inode, reserved);
-	return err;
+	return 0;
 }
 
 static int __es_shrink(struct ext4_sb_info *sbi, int nr_to_scan,
@@ -1707,11 +1787,8 @@
 
 		(*nr_to_scan)--;
 		node = rb_next(&es->rb_node);
-		/*
-		 * We can't reclaim delayed extent from status tree because
-		 * fiemap, bigallic, and seek_data/hole need to use it.
-		 */
-		if (ext4_es_is_delayed(es))
+
+		if (ext4_es_must_keep(es))
 			goto next;
 		if (ext4_es_is_referenced(es)) {
 			ext4_es_clear_referenced(es);
@@ -1775,7 +1852,7 @@
 	while (node) {
 		es = rb_entry(node, struct extent_status, rb_node);
 		node = rb_next(node);
-		if (!ext4_es_is_delayed(es)) {
+		if (!ext4_es_must_keep(es)) {
 			rb_erase(&es->rb_node, &tree->root);
 			ext4_es_free_extent(inode, es);
 		}
@@ -1862,11 +1939,13 @@
  *
  * @inode - file containing the cluster
  * @lblk - logical block in the cluster to be added
+ * @prealloc - preallocated pending entry
  *
  * Returns 0 on successful insertion and -ENOMEM on failure.  If the
  * pending reservation is already in the set, returns successfully.
  */
-static int __insert_pending(struct inode *inode, ext4_lblk_t lblk)
+static int __insert_pending(struct inode *inode, ext4_lblk_t lblk,
+			    struct pending_reservation **prealloc)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
 	struct ext4_pending_tree *tree = &EXT4_I(inode)->i_pending_tree;
@@ -1892,10 +1971,15 @@
 		}
 	}
 
-	pr = kmem_cache_alloc(ext4_pending_cachep, GFP_ATOMIC);
-	if (pr == NULL) {
-		ret = -ENOMEM;
-		goto out;
+	if (likely(*prealloc == NULL)) {
+		pr = __alloc_pending(false);
+		if (!pr) {
+			ret = -ENOMEM;
+			goto out;
+		}
+	} else {
+		pr = *prealloc;
+		*prealloc = NULL;
 	}
 	pr->lclu = lclu;
 
@@ -1925,7 +2009,7 @@
 	if (pr != NULL) {
 		tree = &EXT4_I(inode)->i_pending_tree;
 		rb_erase(&pr->rb_node, &tree->root);
-		kmem_cache_free(ext4_pending_cachep, pr);
+		__free_pending(pr);
 	}
 }
 
@@ -1986,7 +2070,10 @@
 				 bool allocated)
 {
 	struct extent_status newes;
-	int err = 0;
+	int err1 = 0, err2 = 0, err3 = 0;
+	struct extent_status *es1 = NULL;
+	struct extent_status *es2 = NULL;
+	struct pending_reservation *pr = NULL;
 
 	if (EXT4_SB(inode->i_sb)->s_mount_state & EXT4_FC_REPLAY)
 		return 0;
@@ -2001,29 +2088,52 @@
 
 	ext4_es_insert_extent_check(inode, &newes);
 
+retry:
+	if (err1 && !es1)
+		es1 = __es_alloc_extent(true);
+	if ((err1 || err2) && !es2)
+		es2 = __es_alloc_extent(true);
+	if ((err1 || err2 || err3) && allocated && !pr)
+		pr = __alloc_pending(true);
 	write_lock(&EXT4_I(inode)->i_es_lock);
 
-	err = __es_remove_extent(inode, lblk, lblk, NULL);
-	if (err != 0)
-		goto error;
-retry:
-	err = __es_insert_extent(inode, &newes);
-	if (err == -ENOMEM && __es_shrink(EXT4_SB(inode->i_sb),
-					  128, EXT4_I(inode)))
-		goto retry;
-	if (err != 0)
+	err1 = __es_remove_extent(inode, lblk, lblk, NULL, es1);
+	if (err1 != 0)
 		goto error;
+	/* Free preallocated extent if it didn't get used. */
+	if (es1) {
+		if (!es1->es_len)
+			__es_free_extent(es1);
+		es1 = NULL;
+	}
 
-	if (allocated)
-		__insert_pending(inode, lblk);
+	err2 = __es_insert_extent(inode, &newes, es2);
+	if (err2 != 0)
+		goto error;
+	/* Free preallocated extent if it didn't get used. */
+	if (es2) {
+		if (!es2->es_len)
+			__es_free_extent(es2);
+		es2 = NULL;
+	}
 
+	if (allocated) {
+		err3 = __insert_pending(inode, lblk, &pr);
+		if (err3 != 0)
+			goto error;
+		if (pr) {
+			__free_pending(pr);
+			pr = NULL;
+		}
+	}
 error:
 	write_unlock(&EXT4_I(inode)->i_es_lock);
+	if (err1 || err2 || err3)
+		goto retry;
 
 	ext4_es_print_tree(inode);
 	ext4_print_pending_tree(inode);
-
-	return err;
+	return 0;
 }
 
 /*
@@ -2124,21 +2234,24 @@
  * @inode - file containing the range
  * @lblk - logical block defining the start of range
  * @len  - length of range in blocks
+ * @prealloc - preallocated pending entry
  *
  * Used after a newly allocated extent is added to the extents status tree.
  * Requires that the extents in the range have either written or unwritten
  * status.  Must be called while holding i_es_lock.
  */
-static void __revise_pending(struct inode *inode, ext4_lblk_t lblk,
-			     ext4_lblk_t len)
+static int __revise_pending(struct inode *inode, ext4_lblk_t lblk,
+			    ext4_lblk_t len,
+			    struct pending_reservation **prealloc)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
 	ext4_lblk_t end = lblk + len - 1;
 	ext4_lblk_t first, last;
 	bool f_del = false, l_del = false;
+	int ret = 0;
 
 	if (len == 0)
-		return;
+		return 0;
 
 	/*
 	 * Two cases - block range within single cluster and block range
@@ -2159,7 +2272,9 @@
 			f_del = __es_scan_range(inode, &ext4_es_is_delonly,
 						first, lblk - 1);
 		if (f_del) {
-			__insert_pending(inode, first);
+			ret = __insert_pending(inode, first, prealloc);
+			if (ret < 0)
+				goto out;
 		} else {
 			last = EXT4_LBLK_CMASK(sbi, end) +
 			       sbi->s_cluster_ratio - 1;
@@ -2167,9 +2282,11 @@
 				l_del = __es_scan_range(inode,
 							&ext4_es_is_delonly,
 							end + 1, last);
-			if (l_del)
-				__insert_pending(inode, last);
-			else
+			if (l_del) {
+				ret = __insert_pending(inode, last, prealloc);
+				if (ret < 0)
+					goto out;
+			} else
 				__remove_pending(inode, last);
 		}
 	} else {
@@ -2177,18 +2294,24 @@
 		if (first != lblk)
 			f_del = __es_scan_range(inode, &ext4_es_is_delonly,
 						first, lblk - 1);
-		if (f_del)
-			__insert_pending(inode, first);
-		else
+		if (f_del) {
+			ret = __insert_pending(inode, first, prealloc);
+			if (ret < 0)
+				goto out;
+		} else
 			__remove_pending(inode, first);
 
 		last = EXT4_LBLK_CMASK(sbi, end) + sbi->s_cluster_ratio - 1;
 		if (last != end)
 			l_del = __es_scan_range(inode, &ext4_es_is_delonly,
 						end + 1, last);
-		if (l_del)
-			__insert_pending(inode, last);
-		else
+		if (l_del) {
+			ret = __insert_pending(inode, last, prealloc);
+			if (ret < 0)
+				goto out;
+		} else
 			__remove_pending(inode, last);
 	}
+out:
+	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/extents_status.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/extents_status.h
@@ -127,9 +127,9 @@
 extern void ext4_exit_es(void);
 extern void ext4_es_init_tree(struct ext4_es_tree *tree);
 
-extern int ext4_es_insert_extent(struct inode *inode, ext4_lblk_t lblk,
-				 ext4_lblk_t len, ext4_fsblk_t pblk,
-				 unsigned int status);
+extern void ext4_es_insert_extent(struct inode *inode, ext4_lblk_t lblk,
+				  ext4_lblk_t len, ext4_fsblk_t pblk,
+				  unsigned int status);
 extern void ext4_es_cache_extent(struct inode *inode, ext4_lblk_t lblk,
 				 ext4_lblk_t len, ext4_fsblk_t pblk,
 				 unsigned int status);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/fast_commit.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/fast_commit.c
@@ -65,21 +65,11 @@
  *
  * Fast Commit Ineligibility
  * -------------------------
- * Not all operations are supported by fast commits today (e.g extended
- * attributes). Fast commit ineligibility is marked by calling one of the
- * two following functions:
- *
- * - ext4_fc_mark_ineligible(): This makes next fast commit operation to fall
- *   back to full commit. This is useful in case of transient errors.
  *
- * - ext4_fc_start_ineligible() and ext4_fc_stop_ineligible() - This makes all
- *   the fast commits happening between ext4_fc_start_ineligible() and
- *   ext4_fc_stop_ineligible() and one fast commit after the call to
- *   ext4_fc_stop_ineligible() to fall back to full commits. It is important to
- *   make one more fast commit to fall back to full commit after stop call so
- *   that it guaranteed that the fast commit ineligible operation contained
- *   within ext4_fc_start_ineligible() and ext4_fc_stop_ineligible() is
- *   followed by at least 1 full commit.
+ * Not all operations are supported by fast commits today (e.g extended
+ * attributes). Fast commit ineligibility is marked by calling
+ * ext4_fc_mark_ineligible(): This makes next fast commit operation to fall back
+ * to full commit.
  *
  * Atomicity of commits
  * --------------------
@@ -312,61 +302,37 @@
 }
 
 /*
- * Mark file system as fast commit ineligible. This means that next commit
- * operation would result in a full jbd2 commit.
+ * Mark file system as fast commit ineligible, and record latest
+ * ineligible transaction tid. This means until the recorded
+ * transaction, commit operation would result in a full jbd2 commit.
  */
-void ext4_fc_mark_ineligible(struct super_block *sb, int reason)
+void ext4_fc_mark_ineligible(struct super_block *sb, int reason, handle_t *handle)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
+	tid_t tid;
 
 	if (!test_opt2(sb, JOURNAL_FAST_COMMIT) ||
 	    (EXT4_SB(sb)->s_mount_state & EXT4_FC_REPLAY))
 		return;
 
 	ext4_set_mount_flag(sb, EXT4_MF_FC_INELIGIBLE);
+	if (handle && !IS_ERR(handle))
+		tid = handle->h_transaction->t_tid;
+	else {
+		read_lock(&sbi->s_journal->j_state_lock);
+		tid = sbi->s_journal->j_running_transaction ?
+				sbi->s_journal->j_running_transaction->t_tid : 0;
+		read_unlock(&sbi->s_journal->j_state_lock);
+	}
+	spin_lock(&sbi->s_fc_lock);
+	if (tid_gt(tid, sbi->s_fc_ineligible_tid))
+		sbi->s_fc_ineligible_tid = tid;
+	spin_unlock(&sbi->s_fc_lock);
 	WARN_ON(reason >= EXT4_FC_REASON_MAX);
 	sbi->s_fc_stats.fc_ineligible_reason_count[reason]++;
 }
 
 /*
- * Start a fast commit ineligible update. Any commits that happen while
- * such an operation is in progress fall back to full commits.
- */
-void ext4_fc_start_ineligible(struct super_block *sb, int reason)
-{
-	struct ext4_sb_info *sbi = EXT4_SB(sb);
-
-	if (!test_opt2(sb, JOURNAL_FAST_COMMIT) ||
-	    (EXT4_SB(sb)->s_mount_state & EXT4_FC_REPLAY))
-		return;
-
-	WARN_ON(reason >= EXT4_FC_REASON_MAX);
-	sbi->s_fc_stats.fc_ineligible_reason_count[reason]++;
-	atomic_inc(&sbi->s_fc_ineligible_updates);
-}
-
-/*
- * Stop a fast commit ineligible update. We set EXT4_MF_FC_INELIGIBLE flag here
- * to ensure that after stopping the ineligible update, at least one full
- * commit takes place.
- */
-void ext4_fc_stop_ineligible(struct super_block *sb)
-{
-	if (!test_opt2(sb, JOURNAL_FAST_COMMIT) ||
-	    (EXT4_SB(sb)->s_mount_state & EXT4_FC_REPLAY))
-		return;
-
-	ext4_set_mount_flag(sb, EXT4_MF_FC_INELIGIBLE);
-	atomic_dec(&EXT4_SB(sb)->s_fc_ineligible_updates);
-}
-
-static inline int ext4_fc_is_ineligible(struct super_block *sb)
-{
-	return (ext4_test_mount_flag(sb, EXT4_MF_FC_INELIGIBLE) ||
-		atomic_read(&EXT4_SB(sb)->s_fc_ineligible_updates));
-}
-
-/*
  * Generic fast commit tracking function. If this is the first time this we are
  * called after a full commit, we initialize fast commit fields and then call
  * __fc_track_fn() with update = 0. If we have already been called after a full
@@ -378,7 +344,7 @@
  */
 static int ext4_fc_track_template(
 	handle_t *handle, struct inode *inode,
-	int (*__fc_track_fn)(struct inode *, void *, bool),
+	int (*__fc_track_fn)(handle_t *handle, struct inode *, void *, bool),
 	void *args, int enqueue)
 {
 	bool update = false;
@@ -387,13 +353,6 @@
 	tid_t tid = 0;
 	int ret;
 
-	if (!test_opt2(inode->i_sb, JOURNAL_FAST_COMMIT) ||
-	    (sbi->s_mount_state & EXT4_FC_REPLAY))
-		return -EOPNOTSUPP;
-
-	if (ext4_fc_is_ineligible(inode->i_sb))
-		return -EINVAL;
-
 	tid = handle->h_transaction->t_tid;
 	mutex_lock(&ei->i_fc_lock);
 	if (tid == ei->i_sync_tid) {
@@ -402,7 +361,7 @@
 		ext4_fc_reset_inode(inode);
 		ei->i_sync_tid = tid;
 	}
-	ret = __fc_track_fn(inode, args, update);
+	ret = __fc_track_fn(handle, inode, args, update);
 	mutex_unlock(&ei->i_fc_lock);
 
 	if (!enqueue)
@@ -411,7 +370,8 @@
 	spin_lock(&sbi->s_fc_lock);
 	if (list_empty(&EXT4_I(inode)->i_fc_list))
 		list_add_tail(&EXT4_I(inode)->i_fc_list,
-				(ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_COMMITTING)) ?
+				(sbi->s_journal->j_flags & JBD2_FULL_COMMIT_ONGOING ||
+				 sbi->s_journal->j_flags & JBD2_FAST_COMMIT_ONGOING) ?
 				&sbi->s_fc_q[FC_Q_STAGING] :
 				&sbi->s_fc_q[FC_Q_MAIN]);
 	spin_unlock(&sbi->s_fc_lock);
@@ -425,32 +385,42 @@
 };
 
 /* __track_fn for directory entry updates. Called with ei->i_fc_lock. */
-static int __track_dentry_update(struct inode *inode, void *arg, bool update)
+static int __track_dentry_update(handle_t *handle, struct inode *inode,
+				 void *arg, bool update)
 {
 	struct ext4_fc_dentry_update *node;
 	struct ext4_inode_info *ei = EXT4_I(inode);
 	struct __track_dentry_update_args *dentry_update =
 		(struct __track_dentry_update_args *)arg;
 	struct dentry *dentry = dentry_update->dentry;
-	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+	struct inode *dir = dentry->d_parent->d_inode;
+	struct super_block *sb = inode->i_sb;
+	struct ext4_sb_info *sbi = EXT4_SB(sb);
 
 	mutex_unlock(&ei->i_fc_lock);
+
+	if (IS_ENCRYPTED(dir)) {
+		ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_ENCRYPTED_FILENAME,
+					handle);
+		mutex_lock(&ei->i_fc_lock);
+		return -EOPNOTSUPP;
+	}
+
 	node = kmem_cache_alloc(ext4_fc_dentry_cachep, GFP_NOFS);
 	if (!node) {
-		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_NOMEM);
+		ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_NOMEM, handle);
 		mutex_lock(&ei->i_fc_lock);
 		return -ENOMEM;
 	}
 
 	node->fcd_op = dentry_update->op;
-	node->fcd_parent = dentry->d_parent->d_inode->i_ino;
+	node->fcd_parent = dir->i_ino;
 	node->fcd_ino = inode->i_ino;
 	if (dentry->d_name.len > DNAME_INLINE_LEN) {
 		node->fcd_name.name = kmalloc(dentry->d_name.len, GFP_NOFS);
 		if (!node->fcd_name.name) {
 			kmem_cache_free(ext4_fc_dentry_cachep, node);
-			ext4_fc_mark_ineligible(inode->i_sb,
-				EXT4_FC_REASON_NOMEM);
+			ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_NOMEM, handle);
 			mutex_lock(&ei->i_fc_lock);
 			return -ENOMEM;
 		}
@@ -464,7 +434,8 @@
 	node->fcd_name.len = dentry->d_name.len;
 
 	spin_lock(&sbi->s_fc_lock);
-	if (ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_COMMITTING))
+	if (sbi->s_journal->j_flags & JBD2_FULL_COMMIT_ONGOING ||
+		sbi->s_journal->j_flags & JBD2_FAST_COMMIT_ONGOING)
 		list_add_tail(&node->fcd_list,
 				&sbi->s_fc_dentry_q[FC_Q_STAGING]);
 	else
@@ -491,7 +462,17 @@
 
 void ext4_fc_track_unlink(handle_t *handle, struct dentry *dentry)
 {
-	__ext4_fc_track_unlink(handle, d_inode(dentry), dentry);
+	struct inode *inode = d_inode(dentry);
+	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+
+	if (!test_opt2(inode->i_sb, JOURNAL_FAST_COMMIT) ||
+	    (sbi->s_mount_state & EXT4_FC_REPLAY))
+		return;
+
+	if (ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_INELIGIBLE))
+		return;
+
+	__ext4_fc_track_unlink(handle, inode, dentry);
 }
 
 void __ext4_fc_track_link(handle_t *handle,
@@ -510,7 +491,17 @@
 
 void ext4_fc_track_link(handle_t *handle, struct dentry *dentry)
 {
-	__ext4_fc_track_link(handle, d_inode(dentry), dentry);
+	struct inode *inode = d_inode(dentry);
+	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+
+	if (!test_opt2(inode->i_sb, JOURNAL_FAST_COMMIT) ||
+	    (sbi->s_mount_state & EXT4_FC_REPLAY))
+		return;
+
+	if (ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_INELIGIBLE))
+		return;
+
+	__ext4_fc_track_link(handle, inode, dentry);
 }
 
 void __ext4_fc_track_create(handle_t *handle, struct inode *inode,
@@ -529,11 +520,22 @@
 
 void ext4_fc_track_create(handle_t *handle, struct dentry *dentry)
 {
-	__ext4_fc_track_create(handle, d_inode(dentry), dentry);
+	struct inode *inode = d_inode(dentry);
+	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+
+	if (!test_opt2(inode->i_sb, JOURNAL_FAST_COMMIT) ||
+	    (sbi->s_mount_state & EXT4_FC_REPLAY))
+		return;
+
+	if (ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_INELIGIBLE))
+		return;
+
+	__ext4_fc_track_create(handle, inode, dentry);
 }
 
 /* __track_fn for inode tracking */
-static int __track_inode(struct inode *inode, void *arg, bool update)
+static int __track_inode(handle_t *handle, struct inode *inode, void *arg,
+			 bool update)
 {
 	if (update)
 		return -EEXIST;
@@ -545,6 +547,7 @@
 
 void ext4_fc_track_inode(handle_t *handle, struct inode *inode)
 {
+	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
 	int ret;
 
 	if (S_ISDIR(inode->i_mode))
@@ -552,10 +555,17 @@
 
 	if (ext4_should_journal_data(inode)) {
 		ext4_fc_mark_ineligible(inode->i_sb,
-					EXT4_FC_REASON_INODE_JOURNAL_DATA);
+					EXT4_FC_REASON_INODE_JOURNAL_DATA, handle);
 		return;
 	}
 
+	if (!test_opt2(inode->i_sb, JOURNAL_FAST_COMMIT) ||
+	    (sbi->s_mount_state & EXT4_FC_REPLAY))
+		return;
+
+	if (ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_INELIGIBLE))
+		return;
+
 	ret = ext4_fc_track_template(handle, inode, __track_inode, NULL, 1);
 	trace_ext4_fc_track_inode(inode, ret);
 }
@@ -565,7 +575,8 @@
 };
 
 /* __track_fn for tracking data updates */
-static int __track_range(struct inode *inode, void *arg, bool update)
+static int __track_range(handle_t *handle, struct inode *inode, void *arg,
+			 bool update)
 {
 	struct ext4_inode_info *ei = EXT4_I(inode);
 	ext4_lblk_t oldstart;
@@ -595,12 +606,26 @@
 void ext4_fc_track_range(handle_t *handle, struct inode *inode, ext4_lblk_t start,
 			 ext4_lblk_t end)
 {
+	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
 	struct __track_range_args args;
 	int ret;
 
 	if (S_ISDIR(inode->i_mode))
 		return;
 
+	if (!test_opt2(inode->i_sb, JOURNAL_FAST_COMMIT) ||
+	    (sbi->s_mount_state & EXT4_FC_REPLAY))
+		return;
+
+	if (ext4_test_mount_flag(inode->i_sb, EXT4_MF_FC_INELIGIBLE))
+		return;
+
+	if (ext4_has_inline_data(inode)) {
+		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR,
+					handle);
+		return;
+	}
+
 	args.start = start;
 	args.end = end;
 
@@ -627,6 +652,15 @@
 
 /* Ext4 commit path routines */
 
+/* memcpy to fc reserved space and update CRC */
+static void *ext4_fc_memcpy(struct super_block *sb, void *dst, const void *src,
+				int len, u32 *crc)
+{
+	if (crc)
+		*crc = ext4_chksum(EXT4_SB(sb), *crc, src, len);
+	return memcpy(dst, src, len);
+}
+
 /* memzero and update CRC */
 static void *ext4_fc_memzero(struct super_block *sb, void *dst, int len,
 				u32 *crc)
@@ -652,62 +686,59 @@
  */
 static u8 *ext4_fc_reserve_space(struct super_block *sb, int len, u32 *crc)
 {
-	struct ext4_fc_tl *tl;
+	struct ext4_fc_tl tl;
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	struct buffer_head *bh;
 	int bsize = sbi->s_journal->j_blocksize;
 	int ret, off = sbi->s_fc_bytes % bsize;
-	int pad_len;
+	int remaining;
+	u8 *dst;
 
 	/*
-	 * After allocating len, we should have space at least for a 0 byte
-	 * padding.
+	 * If 'len' is too long to fit in any block alongside a PAD tlv, then we
+	 * cannot fulfill the request.
 	 */
-	if (len + sizeof(struct ext4_fc_tl) > bsize)
+	if (len > bsize - EXT4_FC_TAG_BASE_LEN)
 		return NULL;
 
-	if (bsize - off - 1 > len + sizeof(struct ext4_fc_tl)) {
-		/*
-		 * Only allocate from current buffer if we have enough space for
-		 * this request AND we have space to add a zero byte padding.
-		 */
-		if (!sbi->s_fc_bh) {
-			ret = jbd2_fc_get_buf(EXT4_SB(sb)->s_journal, &bh);
-			if (ret)
-				return NULL;
-			sbi->s_fc_bh = bh;
-		}
+	if (!sbi->s_fc_bh) {
+		ret = jbd2_fc_get_buf(EXT4_SB(sb)->s_journal, &bh);
+		if (ret)
+			return NULL;
+		sbi->s_fc_bh = bh;
+	}
+	dst = sbi->s_fc_bh->b_data + off;
+
+	/*
+	 * Allocate the bytes in the current block if we can do so while still
+	 * leaving enough space for a PAD tlv.
+	 */
+	remaining = bsize - EXT4_FC_TAG_BASE_LEN - off;
+	if (len <= remaining) {
 		sbi->s_fc_bytes += len;
-		return sbi->s_fc_bh->b_data + off;
+		return dst;
 	}
-	/* Need to add PAD tag */
-	tl = (struct ext4_fc_tl *)(sbi->s_fc_bh->b_data + off);
-	tl->fc_tag = cpu_to_le16(EXT4_FC_TAG_PAD);
-	pad_len = bsize - off - 1 - sizeof(struct ext4_fc_tl);
-	tl->fc_len = cpu_to_le16(pad_len);
-	if (crc)
-		*crc = ext4_chksum(sbi, *crc, tl, sizeof(*tl));
-	if (pad_len > 0)
-		ext4_fc_memzero(sb, tl + 1, pad_len, crc);
+
+	/*
+	 * Else, terminate the current block with a PAD tlv, then allocate a new
+	 * block and allocate the bytes at the start of that new block.
+	 */
+
+	tl.fc_tag = cpu_to_le16(EXT4_FC_TAG_PAD);
+	tl.fc_len = cpu_to_le16(remaining);
+	ext4_fc_memcpy(sb, dst, &tl, EXT4_FC_TAG_BASE_LEN, crc);
+	ext4_fc_memzero(sb, dst + EXT4_FC_TAG_BASE_LEN, remaining, crc);
+
 	ext4_fc_submit_bh(sb, false);
 
 	ret = jbd2_fc_get_buf(EXT4_SB(sb)->s_journal, &bh);
 	if (ret)
 		return NULL;
 	sbi->s_fc_bh = bh;
-	sbi->s_fc_bytes = (sbi->s_fc_bytes / bsize + 1) * bsize + len;
+	sbi->s_fc_bytes += bsize - off + len;
 	return sbi->s_fc_bh->b_data;
 }
 
-/* memcpy to fc reserved space and update CRC */
-static void *ext4_fc_memcpy(struct super_block *sb, void *dst, const void *src,
-				int len, u32 *crc)
-{
-	if (crc)
-		*crc = ext4_chksum(EXT4_SB(sb), *crc, src, len);
-	return memcpy(dst, src, len);
-}
-
 /*
  * Complete a fast commit by writing tail tag.
  *
@@ -728,23 +759,25 @@
 	 * ext4_fc_reserve_space takes care of allocating an extra block if
 	 * there's no enough space on this block for accommodating this tail.
 	 */
-	dst = ext4_fc_reserve_space(sb, sizeof(tl) + sizeof(tail), &crc);
+	dst = ext4_fc_reserve_space(sb, EXT4_FC_TAG_BASE_LEN + sizeof(tail), &crc);
 	if (!dst)
 		return -ENOSPC;
 
 	off = sbi->s_fc_bytes % bsize;
 
 	tl.fc_tag = cpu_to_le16(EXT4_FC_TAG_TAIL);
-	tl.fc_len = cpu_to_le16(bsize - off - 1 + sizeof(struct ext4_fc_tail));
+	tl.fc_len = cpu_to_le16(bsize - off + sizeof(struct ext4_fc_tail));
 	sbi->s_fc_bytes = round_up(sbi->s_fc_bytes, bsize);
 
-	ext4_fc_memcpy(sb, dst, &tl, sizeof(tl), &crc);
-	dst += sizeof(tl);
+	ext4_fc_memcpy(sb, dst, &tl, EXT4_FC_TAG_BASE_LEN, &crc);
+	dst += EXT4_FC_TAG_BASE_LEN;
 	tail.fc_tid = cpu_to_le32(sbi->s_journal->j_running_transaction->t_tid);
 	ext4_fc_memcpy(sb, dst, &tail.fc_tid, sizeof(tail.fc_tid), &crc);
 	dst += sizeof(tail.fc_tid);
 	tail.fc_crc = cpu_to_le32(crc);
 	ext4_fc_memcpy(sb, dst, &tail.fc_crc, sizeof(tail.fc_crc), NULL);
+	dst += sizeof(tail.fc_crc);
+	memset(dst, 0, bsize - off); /* Don't leak uninitialized memory. */
 
 	ext4_fc_submit_bh(sb, true);
 
@@ -761,15 +794,15 @@
 	struct ext4_fc_tl tl;
 	u8 *dst;
 
-	dst = ext4_fc_reserve_space(sb, sizeof(tl) + len, crc);
+	dst = ext4_fc_reserve_space(sb, EXT4_FC_TAG_BASE_LEN + len, crc);
 	if (!dst)
 		return false;
 
 	tl.fc_tag = cpu_to_le16(tag);
 	tl.fc_len = cpu_to_le16(len);
 
-	ext4_fc_memcpy(sb, dst, &tl, sizeof(tl), crc);
-	ext4_fc_memcpy(sb, dst + sizeof(tl), val, len, crc);
+	ext4_fc_memcpy(sb, dst, &tl, EXT4_FC_TAG_BASE_LEN, crc);
+	ext4_fc_memcpy(sb, dst + EXT4_FC_TAG_BASE_LEN, val, len, crc);
 
 	return true;
 }
@@ -781,8 +814,8 @@
 	struct ext4_fc_dentry_info fcd;
 	struct ext4_fc_tl tl;
 	int dlen = fc_dentry->fcd_name.len;
-	u8 *dst = ext4_fc_reserve_space(sb, sizeof(tl) + sizeof(fcd) + dlen,
-					crc);
+	u8 *dst = ext4_fc_reserve_space(sb,
+			EXT4_FC_TAG_BASE_LEN + sizeof(fcd) + dlen, crc);
 
 	if (!dst)
 		return false;
@@ -791,8 +824,8 @@
 	fcd.fc_ino = cpu_to_le32(fc_dentry->fcd_ino);
 	tl.fc_tag = cpu_to_le16(fc_dentry->fcd_op);
 	tl.fc_len = cpu_to_le16(sizeof(fcd) + dlen);
-	ext4_fc_memcpy(sb, dst, &tl, sizeof(tl), crc);
-	dst += sizeof(tl);
+	ext4_fc_memcpy(sb, dst, &tl, EXT4_FC_TAG_BASE_LEN, crc);
+	dst += EXT4_FC_TAG_BASE_LEN;
 	ext4_fc_memcpy(sb, dst, &fcd, sizeof(fcd), crc);
 	dst += sizeof(fcd);
 	ext4_fc_memcpy(sb, dst, fc_dentry->fcd_name.name, dlen, crc);
@@ -826,22 +859,25 @@
 	tl.fc_tag = cpu_to_le16(EXT4_FC_TAG_INODE);
 	tl.fc_len = cpu_to_le16(inode_len + sizeof(fc_inode.fc_ino));
 
+	ret = -ECANCELED;
 	dst = ext4_fc_reserve_space(inode->i_sb,
-			sizeof(tl) + inode_len + sizeof(fc_inode.fc_ino), crc);
+		EXT4_FC_TAG_BASE_LEN + inode_len + sizeof(fc_inode.fc_ino), crc);
 	if (!dst)
-		return -ECANCELED;
+		goto err;
 
-	if (!ext4_fc_memcpy(inode->i_sb, dst, &tl, sizeof(tl), crc))
-		return -ECANCELED;
-	dst += sizeof(tl);
+	if (!ext4_fc_memcpy(inode->i_sb, dst, &tl, EXT4_FC_TAG_BASE_LEN, crc))
+		goto err;
+	dst += EXT4_FC_TAG_BASE_LEN;
 	if (!ext4_fc_memcpy(inode->i_sb, dst, &fc_inode, sizeof(fc_inode), crc))
-		return -ECANCELED;
+		goto err;
 	dst += sizeof(fc_inode);
 	if (!ext4_fc_memcpy(inode->i_sb, dst, (u8 *)ext4_raw_inode(&iloc),
 					inode_len, crc))
-		return -ECANCELED;
-
-	return 0;
+		goto err;
+	ret = 0;
+err:
+	brelse(iloc.bh);
+	return ret;
 }
 
 /*
@@ -869,8 +905,8 @@
 	mutex_unlock(&ei->i_fc_lock);
 
 	cur_lblk_off = old_blk_size;
-	jbd_debug(1, "%s: will try writing %d to %d for inode %ld\n",
-		  __func__, cur_lblk_off, new_blk_size, inode->i_ino);
+	ext4_debug("will try writing %d to %d for inode %ld\n",
+		   cur_lblk_off, new_blk_size, inode->i_ino);
 
 	while (cur_lblk_off <= new_blk_size) {
 		map.m_lblk = cur_lblk_off;
@@ -928,7 +964,6 @@
 	int ret = 0;
 
 	spin_lock(&sbi->s_fc_lock);
-	ext4_set_mount_flag(sb, EXT4_MF_FC_COMMITTING);
 	list_for_each_entry(ei, &sbi->s_fc_q[FC_Q_MAIN], i_fc_list) {
 		ext4_set_inode_state(&ei->vfs_inode, EXT4_STATE_FC_COMMITTING);
 		while (atomic_read(&ei->i_fc_updates)) {
@@ -1121,6 +1156,32 @@
 	return ret;
 }
 
+static void ext4_fc_update_stats(struct super_block *sb, int status,
+				 u64 commit_time, int nblks)
+{
+	struct ext4_fc_stats *stats = &EXT4_SB(sb)->s_fc_stats;
+
+	ext4_debug("Fast commit ended with status = %d", status);
+	if (status == EXT4_FC_STATUS_OK) {
+		stats->fc_num_commits++;
+		stats->fc_numblks += nblks;
+		if (likely(stats->s_fc_avg_commit_time))
+			stats->s_fc_avg_commit_time =
+				(commit_time +
+				 stats->s_fc_avg_commit_time * 3) / 4;
+		else
+			stats->s_fc_avg_commit_time = commit_time;
+	} else if (status == EXT4_FC_STATUS_FAILED ||
+		   status == EXT4_FC_STATUS_INELIGIBLE) {
+		if (status == EXT4_FC_STATUS_FAILED)
+			stats->fc_failed_commits++;
+		stats->fc_ineligible_commits++;
+	} else {
+		stats->fc_skipped_commits++;
+	}
+	trace_ext4_fc_commit_stop(sb, nblks, status);
+}
+
 /*
  * The main commit entry point. Performs a fast commit for transaction
  * commit_tid if needed. If it's not possible to perform a fast commit
@@ -1133,94 +1194,76 @@
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	int nblks = 0, ret, bsize = journal->j_blocksize;
 	int subtid = atomic_read(&sbi->s_fc_subtid);
-	int reason = EXT4_FC_REASON_OK, fc_bufs_before = 0;
+	int status = EXT4_FC_STATUS_OK, fc_bufs_before = 0;
 	ktime_t start_time, commit_time;
 
 	trace_ext4_fc_commit_start(sb);
 
 	start_time = ktime_get();
 
-	if (!test_opt2(sb, JOURNAL_FAST_COMMIT) ||
-		(ext4_fc_is_ineligible(sb))) {
-		reason = EXT4_FC_REASON_INELIGIBLE;
-		goto out;
-	}
+	if (!test_opt2(sb, JOURNAL_FAST_COMMIT))
+		return jbd2_complete_transaction(journal, commit_tid);
 
 restart_fc:
 	ret = jbd2_fc_begin_commit(journal, commit_tid);
 	if (ret == -EALREADY) {
 		/* There was an ongoing commit, check if we need to restart */
 		if (atomic_read(&sbi->s_fc_subtid) <= subtid &&
-			commit_tid > journal->j_commit_sequence)
+		    tid_gt(commit_tid, journal->j_commit_sequence))
 			goto restart_fc;
-		reason = EXT4_FC_REASON_ALREADY_COMMITTED;
-		goto out;
+		ext4_fc_update_stats(sb, EXT4_FC_STATUS_SKIPPED, 0, 0);
+		return 0;
 	} else if (ret) {
-		sbi->s_fc_stats.fc_ineligible_reason_count[EXT4_FC_COMMIT_FAILED]++;
-		reason = EXT4_FC_REASON_FC_START_FAILED;
-		goto out;
+		/*
+		 * Commit couldn't start. Just update stats and perform a
+		 * full commit.
+		 */
+		ext4_fc_update_stats(sb, EXT4_FC_STATUS_FAILED, 0, 0);
+		return jbd2_complete_transaction(journal, commit_tid);
+	}
+
+	/*
+	 * After establishing journal barrier via jbd2_fc_begin_commit(), check
+	 * if we are fast commit ineligible.
+	 */
+	if (ext4_test_mount_flag(sb, EXT4_MF_FC_INELIGIBLE)) {
+		status = EXT4_FC_STATUS_INELIGIBLE;
+		goto fallback;
 	}
 
 	fc_bufs_before = (sbi->s_fc_bytes + bsize - 1) / bsize;
 	ret = ext4_fc_perform_commit(journal);
 	if (ret < 0) {
-		sbi->s_fc_stats.fc_ineligible_reason_count[EXT4_FC_COMMIT_FAILED]++;
-		reason = EXT4_FC_REASON_FC_FAILED;
-		goto out;
+		status = EXT4_FC_STATUS_FAILED;
+		goto fallback;
 	}
 	nblks = (sbi->s_fc_bytes + bsize - 1) / bsize - fc_bufs_before;
 	ret = jbd2_fc_wait_bufs(journal, nblks);
 	if (ret < 0) {
-		sbi->s_fc_stats.fc_ineligible_reason_count[EXT4_FC_COMMIT_FAILED]++;
-		reason = EXT4_FC_REASON_FC_FAILED;
-		goto out;
+		status = EXT4_FC_STATUS_FAILED;
+		goto fallback;
 	}
 	atomic_inc(&sbi->s_fc_subtid);
-	jbd2_fc_end_commit(journal);
-out:
-	/* Has any ineligible update happened since we started? */
-	if (reason == EXT4_FC_REASON_OK && ext4_fc_is_ineligible(sb)) {
-		sbi->s_fc_stats.fc_ineligible_reason_count[EXT4_FC_COMMIT_FAILED]++;
-		reason = EXT4_FC_REASON_INELIGIBLE;
-	}
-
-	spin_lock(&sbi->s_fc_lock);
-	if (reason != EXT4_FC_REASON_OK &&
-		reason != EXT4_FC_REASON_ALREADY_COMMITTED) {
-		sbi->s_fc_stats.fc_ineligible_commits++;
-	} else {
-		sbi->s_fc_stats.fc_num_commits++;
-		sbi->s_fc_stats.fc_numblks += nblks;
-	}
-	spin_unlock(&sbi->s_fc_lock);
-	nblks = (reason == EXT4_FC_REASON_OK) ? nblks : 0;
-	trace_ext4_fc_commit_stop(sb, nblks, reason);
-	commit_time = ktime_to_ns(ktime_sub(ktime_get(), start_time));
+	ret = jbd2_fc_end_commit(journal);
 	/*
-	 * weight the commit time higher than the average time so we don't
-	 * react too strongly to vast changes in the commit time
+	 * weight the commit time higher than the average time so we
+	 * don't react too strongly to vast changes in the commit time
 	 */
-	if (likely(sbi->s_fc_avg_commit_time))
-		sbi->s_fc_avg_commit_time = (commit_time +
-				sbi->s_fc_avg_commit_time * 3) / 4;
-	else
-		sbi->s_fc_avg_commit_time = commit_time;
-	jbd_debug(1,
-		"Fast commit ended with blks = %d, reason = %d, subtid - %d",
-		nblks, reason, subtid);
-	if (reason == EXT4_FC_REASON_FC_FAILED)
-		return jbd2_fc_end_commit_fallback(journal);
-	if (reason == EXT4_FC_REASON_FC_START_FAILED ||
-		reason == EXT4_FC_REASON_INELIGIBLE)
-		return jbd2_complete_transaction(journal, commit_tid);
-	return 0;
+	commit_time = ktime_to_ns(ktime_sub(ktime_get(), start_time));
+	ext4_fc_update_stats(sb, status, commit_time, nblks);
+	return ret;
+
+fallback:
+	ret = jbd2_fc_end_commit_fallback(journal);
+	ext4_fc_update_stats(sb, status, 0, 0);
+	return ret;
 }
 
 /*
  * Fast commit cleanup routine. This is called after every fast commit and
  * full commit. full is true if we are called after a full commit.
  */
-static void ext4_fc_cleanup(journal_t *journal, int full)
+static void ext4_fc_cleanup(journal_t *journal, int full, tid_t tid)
 {
 	struct super_block *sb = journal->j_private;
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
@@ -1238,7 +1281,21 @@
 		list_del_init(&iter->i_fc_list);
 		ext4_clear_inode_state(&iter->vfs_inode,
 				       EXT4_STATE_FC_COMMITTING);
-		ext4_fc_reset_inode(&iter->vfs_inode);
+		if (tid_geq(tid, iter->i_sync_tid)) {
+			ext4_fc_reset_inode(&iter->vfs_inode);
+		} else if (full) {
+			/*
+			 * We are called after a full commit, inode has been
+			 * modified while the commit was running. Re-enqueue
+			 * the inode into STAGING, which will then be splice
+			 * back into MAIN. This cannot happen during
+			 * fastcommit because the journal is locked all the
+			 * time in that case (and tid doesn't increase so
+			 * tid check above isn't reliable).
+			 */
+			list_add_tail(&EXT4_I(&iter->vfs_inode)->i_fc_list,
+				      &sbi->s_fc_q[FC_Q_STAGING]);
+		}
 		/* Make sure EXT4_STATE_FC_COMMITTING bit is clear */
 		smp_mb();
 #if (BITS_PER_LONG < 64)
@@ -1267,8 +1324,10 @@
 	list_splice_init(&sbi->s_fc_q[FC_Q_STAGING],
 				&sbi->s_fc_q[FC_Q_MAIN]);
 
-	ext4_clear_mount_flag(sb, EXT4_MF_FC_COMMITTING);
-	ext4_clear_mount_flag(sb, EXT4_MF_FC_INELIGIBLE);
+	if (tid_geq(tid, sbi->s_fc_ineligible_tid)) {
+		sbi->s_fc_ineligible_tid = 0;
+		ext4_clear_mount_flag(sb, EXT4_MF_FC_INELIGIBLE);
+	}
 
 	if (full)
 		sbi->s_fc_bytes = 0;
@@ -1284,8 +1343,14 @@
 	char *dname;
 };
 
+/* Same as struct ext4_fc_tl, but uses native endianness fields */
+struct ext4_fc_tl_mem {
+	u16 fc_tag;
+	u16 fc_len;
+};
+
 static inline void tl_to_darg(struct dentry_info_args *darg,
-			      struct  ext4_fc_tl *tl, u8 *val)
+			      struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	struct ext4_fc_dentry_info fcd;
 
@@ -1294,13 +1359,21 @@
 	darg->parent_ino = le32_to_cpu(fcd.fc_parent_ino);
 	darg->ino = le32_to_cpu(fcd.fc_ino);
 	darg->dname = val + offsetof(struct ext4_fc_dentry_info, fc_dname);
-	darg->dname_len = le16_to_cpu(tl->fc_len) -
-		sizeof(struct ext4_fc_dentry_info);
+	darg->dname_len = tl->fc_len - sizeof(struct ext4_fc_dentry_info);
+}
+
+static inline void ext4_fc_get_tl(struct ext4_fc_tl_mem *tl, u8 *val)
+{
+	struct ext4_fc_tl tl_disk;
+
+	memcpy(&tl_disk, val, EXT4_FC_TAG_BASE_LEN);
+	tl->fc_len = le16_to_cpu(tl_disk.fc_len);
+	tl->fc_tag = le16_to_cpu(tl_disk.fc_tag);
 }
 
 /* Unlink replay function */
-static int ext4_fc_replay_unlink(struct super_block *sb, struct ext4_fc_tl *tl,
-				 u8 *val)
+static int ext4_fc_replay_unlink(struct super_block *sb,
+				 struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	struct inode *inode, *old_parent;
 	struct qstr entry;
@@ -1317,19 +1390,19 @@
 	inode = ext4_iget(sb, darg.ino, EXT4_IGET_NORMAL);
 
 	if (IS_ERR(inode)) {
-		jbd_debug(1, "Inode %d not found", darg.ino);
+		ext4_debug("Inode %d not found", darg.ino);
 		return 0;
 	}
 
 	old_parent = ext4_iget(sb, darg.parent_ino,
 				EXT4_IGET_NORMAL);
 	if (IS_ERR(old_parent)) {
-		jbd_debug(1, "Dir with inode  %d not found", darg.parent_ino);
+		ext4_debug("Dir with inode %d not found", darg.parent_ino);
 		iput(inode);
 		return 0;
 	}
 
-	ret = __ext4_unlink(NULL, old_parent, &entry, inode);
+	ret = __ext4_unlink(old_parent, &entry, inode, NULL);
 	/* -ENOENT ok coz it might not exist anymore. */
 	if (ret == -ENOENT)
 		ret = 0;
@@ -1349,21 +1422,21 @@
 
 	dir = ext4_iget(sb, darg->parent_ino, EXT4_IGET_NORMAL);
 	if (IS_ERR(dir)) {
-		jbd_debug(1, "Dir with inode %d not found.", darg->parent_ino);
+		ext4_debug("Dir with inode %d not found.", darg->parent_ino);
 		dir = NULL;
 		goto out;
 	}
 
 	dentry_dir = d_obtain_alias(dir);
 	if (IS_ERR(dentry_dir)) {
-		jbd_debug(1, "Failed to obtain dentry");
+		ext4_debug("Failed to obtain dentry");
 		dentry_dir = NULL;
 		goto out;
 	}
 
 	dentry_inode = d_alloc(dentry_dir, &qstr_dname);
 	if (!dentry_inode) {
-		jbd_debug(1, "Inode dentry not created.");
+		ext4_debug("Inode dentry not created.");
 		ret = -ENOMEM;
 		goto out;
 	}
@@ -1376,7 +1449,7 @@
 	 * could complete.
 	 */
 	if (ret && ret != -EEXIST) {
-		jbd_debug(1, "Failed to link\n");
+		ext4_debug("Failed to link\n");
 		goto out;
 	}
 
@@ -1397,8 +1470,8 @@
 }
 
 /* Link replay function */
-static int ext4_fc_replay_link(struct super_block *sb, struct ext4_fc_tl *tl,
-			       u8 *val)
+static int ext4_fc_replay_link(struct super_block *sb,
+			       struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	struct inode *inode;
 	struct dentry_info_args darg;
@@ -1410,7 +1483,7 @@
 
 	inode = ext4_iget(sb, darg.ino, EXT4_IGET_NORMAL);
 	if (IS_ERR(inode)) {
-		jbd_debug(1, "Inode not found.");
+		ext4_debug("Inode not found.");
 		return 0;
 	}
 
@@ -1433,14 +1506,17 @@
 		if (state->fc_modified_inodes[i] == ino)
 			return 0;
 	if (state->fc_modified_inodes_used == state->fc_modified_inodes_size) {
+		int *fc_modified_inodes;
+
+		fc_modified_inodes = krealloc(state->fc_modified_inodes,
+				sizeof(int) * (state->fc_modified_inodes_size +
+				EXT4_FC_REPLAY_REALLOC_INCREMENT),
+				GFP_KERNEL);
+		if (!fc_modified_inodes)
+			return -ENOMEM;
+		state->fc_modified_inodes = fc_modified_inodes;
 		state->fc_modified_inodes_size +=
 			EXT4_FC_REPLAY_REALLOC_INCREMENT;
-		state->fc_modified_inodes = krealloc(
-					state->fc_modified_inodes, sizeof(int) *
-					state->fc_modified_inodes_size,
-					GFP_KERNEL);
-		if (!state->fc_modified_inodes)
-			return -ENOMEM;
 	}
 	state->fc_modified_inodes[state->fc_modified_inodes_used++] = ino;
 	return 0;
@@ -1449,15 +1525,15 @@
 /*
  * Inode replay function
  */
-static int ext4_fc_replay_inode(struct super_block *sb, struct ext4_fc_tl *tl,
-				u8 *val)
+static int ext4_fc_replay_inode(struct super_block *sb,
+				struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	struct ext4_fc_inode fc_inode;
 	struct ext4_inode *raw_inode;
 	struct ext4_inode *raw_fc_inode;
 	struct inode *inode = NULL;
 	struct ext4_iloc iloc;
-	int inode_len, ino, ret, tag = le16_to_cpu(tl->fc_tag);
+	int inode_len, ino, ret, tag = tl->fc_tag;
 	struct ext4_extent_header *eh;
 
 	memcpy(&fc_inode, val, sizeof(fc_inode));
@@ -1472,7 +1548,9 @@
 	}
 	inode = NULL;
 
-	ext4_fc_record_modified_inode(sb, ino);
+	ret = ext4_fc_record_modified_inode(sb, ino);
+	if (ret)
+		goto out;
 
 	raw_fc_inode = (struct ext4_inode *)
 		(val + offsetof(struct ext4_fc_inode, fc_raw_inode));
@@ -1480,7 +1558,7 @@
 	if (ret)
 		goto out;
 
-	inode_len = le16_to_cpu(tl->fc_len) - sizeof(struct ext4_fc_inode);
+	inode_len = tl->fc_len - sizeof(struct ext4_fc_inode);
 	raw_inode = ext4_raw_inode(&iloc);
 
 	memcpy(raw_inode, raw_fc_inode, offsetof(struct ext4_inode, i_block));
@@ -1515,7 +1593,7 @@
 	/* Given that we just wrote the inode on disk, this SHOULD succeed. */
 	inode = ext4_iget(sb, ino, EXT4_IGET_NORMAL);
 	if (IS_ERR(inode)) {
-		jbd_debug(1, "Inode not found.");
+		ext4_debug("Inode not found.");
 		return -EFSCORRUPTED;
 	}
 
@@ -1548,8 +1626,8 @@
  * inode for which we are trying to create a dentry here, should already have
  * been replayed before we start here.
  */
-static int ext4_fc_replay_create(struct super_block *sb, struct ext4_fc_tl *tl,
-				 u8 *val)
+static int ext4_fc_replay_create(struct super_block *sb,
+				 struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	int ret = 0;
 	struct inode *inode = NULL;
@@ -1568,7 +1646,7 @@
 
 	inode = ext4_iget(sb, darg.ino, EXT4_IGET_NORMAL);
 	if (IS_ERR(inode)) {
-		jbd_debug(1, "inode %d not found.", darg.ino);
+		ext4_debug("inode %d not found.", darg.ino);
 		inode = NULL;
 		ret = -EINVAL;
 		goto out;
@@ -1581,7 +1659,7 @@
 		 */
 		dir = ext4_iget(sb, darg.parent_ino, EXT4_IGET_NORMAL);
 		if (IS_ERR(dir)) {
-			jbd_debug(1, "Dir %d not found.", darg.ino);
+			ext4_debug("Dir %d not found.", darg.ino);
 			goto out;
 		}
 		ret = ext4_init_new_dir(NULL, dir, inode);
@@ -1603,26 +1681,36 @@
 }
 
 /*
- * Record physical disk regions which are in use as per fast commit area. Our
- * simple replay phase allocator excludes these regions from allocation.
+ * Record physical disk regions which are in use as per fast commit area,
+ * and used by inodes during replay phase. Our simple replay phase
+ * allocator excludes these regions from allocation.
  */
-static int ext4_fc_record_regions(struct super_block *sb, int ino,
-		ext4_lblk_t lblk, ext4_fsblk_t pblk, int len)
+int ext4_fc_record_regions(struct super_block *sb, int ino,
+		ext4_lblk_t lblk, ext4_fsblk_t pblk, int len, int replay)
 {
 	struct ext4_fc_replay_state *state;
 	struct ext4_fc_alloc_region *region;
 
 	state = &EXT4_SB(sb)->s_fc_replay_state;
+	/*
+	 * during replay phase, the fc_regions_valid may not same as
+	 * fc_regions_used, update it when do new additions.
+	 */
+	if (replay && state->fc_regions_used != state->fc_regions_valid)
+		state->fc_regions_used = state->fc_regions_valid;
 	if (state->fc_regions_used == state->fc_regions_size) {
+		struct ext4_fc_alloc_region *fc_regions;
+
+		fc_regions = krealloc(state->fc_regions,
+				      sizeof(struct ext4_fc_alloc_region) *
+				      (state->fc_regions_size +
+				       EXT4_FC_REPLAY_REALLOC_INCREMENT),
+				      GFP_KERNEL);
+		if (!fc_regions)
+			return -ENOMEM;
 		state->fc_regions_size +=
 			EXT4_FC_REPLAY_REALLOC_INCREMENT;
-		state->fc_regions = krealloc(
-					state->fc_regions,
-					state->fc_regions_size *
-					sizeof(struct ext4_fc_alloc_region),
-					GFP_KERNEL);
-		if (!state->fc_regions)
-			return -ENOMEM;
+		state->fc_regions = fc_regions;
 	}
 	region = &state->fc_regions[state->fc_regions_used++];
 	region->ino = ino;
@@ -1630,12 +1718,15 @@
 	region->pblk = pblk;
 	region->len = len;
 
+	if (replay)
+		state->fc_regions_valid++;
+
 	return 0;
 }
 
 /* Replay add range tag */
 static int ext4_fc_replay_add_range(struct super_block *sb,
-				    struct ext4_fc_tl *tl, u8 *val)
+				    struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	struct ext4_fc_add_range fc_add_ex;
 	struct ext4_extent newex, *ex;
@@ -1656,11 +1747,13 @@
 
 	inode = ext4_iget(sb, le32_to_cpu(fc_add_ex.fc_ino), EXT4_IGET_NORMAL);
 	if (IS_ERR(inode)) {
-		jbd_debug(1, "Inode not found.");
+		ext4_debug("Inode not found.");
 		return 0;
 	}
 
 	ret = ext4_fc_record_modified_inode(sb, inode->i_ino);
+	if (ret)
+		goto out;
 
 	start = le32_to_cpu(ex->ee_block);
 	start_pblk = ext4_ext_pblock(ex);
@@ -1668,7 +1761,7 @@
 
 	cur = start;
 	remaining = len;
-	jbd_debug(1, "ADD_RANGE, lblk %d, pblk %lld, len %d, unwritten %d, inode %ld\n",
+	ext4_debug("ADD_RANGE, lblk %d, pblk %lld, len %d, unwritten %d, inode %ld\n",
 		  start, start_pblk, len, ext4_ext_is_unwritten(ex),
 		  inode->i_ino);
 
@@ -1678,18 +1771,14 @@
 		map.m_pblk = 0;
 		ret = ext4_map_blocks(NULL, inode, &map, 0);
 
-		if (ret < 0) {
-			iput(inode);
-			return 0;
-		}
+		if (ret < 0)
+			goto out;
 
 		if (ret == 0) {
 			/* Range is not mapped */
 			path = ext4_find_extent(inode, cur, NULL, 0);
-			if (IS_ERR(path)) {
-				iput(inode);
-				return 0;
-			}
+			if (IS_ERR(path))
+				goto out;
 			memset(&newex, 0, sizeof(newex));
 			newex.ee_block = cpu_to_le32(cur);
 			ext4_ext_store_pblock(
@@ -1703,10 +1792,8 @@
 			up_write((&EXT4_I(inode)->i_data_sem));
 			ext4_ext_drop_refs(path);
 			kfree(path);
-			if (ret) {
-				iput(inode);
-				return 0;
-			}
+			if (ret)
+				goto out;
 			goto next;
 		}
 
@@ -1719,10 +1806,8 @@
 			ret = ext4_ext_replay_update_ex(inode, cur, map.m_len,
 					ext4_ext_is_unwritten(ex),
 					start_pblk + cur - start);
-			if (ret) {
-				iput(inode);
-				return 0;
-			}
+			if (ret)
+				goto out;
 			/*
 			 * Mark the old blocks as free since they aren't used
 			 * anymore. We maintain an array of all the modified
@@ -1737,15 +1822,13 @@
 		}
 
 		/* Range is mapped and needs a state change */
-		jbd_debug(1, "Converting from %ld to %d %lld",
+		ext4_debug("Converting from %ld to %d %lld",
 				map.m_flags & EXT4_MAP_UNWRITTEN,
 			ext4_ext_is_unwritten(ex), map.m_pblk);
 		ret = ext4_ext_replay_update_ex(inode, cur, map.m_len,
 					ext4_ext_is_unwritten(ex), map.m_pblk);
-		if (ret) {
-			iput(inode);
-			return 0;
-		}
+		if (ret)
+			goto out;
 		/*
 		 * We may have split the extent tree while toggling the state.
 		 * Try to shrink the extent tree now.
@@ -1757,14 +1840,15 @@
 	}
 	ext4_ext_replay_shrink_inode(inode, i_size_read(inode) >>
 					sb->s_blocksize_bits);
+out:
 	iput(inode);
 	return 0;
 }
 
 /* Replay DEL_RANGE tag */
 static int
-ext4_fc_replay_del_range(struct super_block *sb, struct ext4_fc_tl *tl,
-			 u8 *val)
+ext4_fc_replay_del_range(struct super_block *sb,
+			 struct ext4_fc_tl_mem *tl, u8 *val)
 {
 	struct inode *inode;
 	struct ext4_fc_del_range lrange;
@@ -1781,13 +1865,15 @@
 
 	inode = ext4_iget(sb, le32_to_cpu(lrange.fc_ino), EXT4_IGET_NORMAL);
 	if (IS_ERR(inode)) {
-		jbd_debug(1, "Inode %d not found", le32_to_cpu(lrange.fc_ino));
+		ext4_debug("Inode %d not found", le32_to_cpu(lrange.fc_ino));
 		return 0;
 	}
 
 	ret = ext4_fc_record_modified_inode(sb, inode->i_ino);
+	if (ret)
+		goto out;
 
-	jbd_debug(1, "DEL_RANGE, inode %ld, lblk %d, len %d\n",
+	ext4_debug("DEL_RANGE, inode %ld, lblk %d, len %d\n",
 			inode->i_ino, le32_to_cpu(lrange.fc_lblk),
 			le32_to_cpu(lrange.fc_len));
 	while (remaining > 0) {
@@ -1795,10 +1881,8 @@
 		map.m_len = remaining;
 
 		ret = ext4_map_blocks(NULL, inode, &map, 0);
-		if (ret < 0) {
-			iput(inode);
-			return 0;
-		}
+		if (ret < 0)
+			goto out;
 		if (ret > 0) {
 			remaining -= ret;
 			cur += ret;
@@ -1809,16 +1893,18 @@
 		}
 	}
 
-	ret = ext4_punch_hole(inode,
-		le32_to_cpu(lrange.fc_lblk) << sb->s_blocksize_bits,
-		le32_to_cpu(lrange.fc_len) <<  sb->s_blocksize_bits);
+	down_write(&EXT4_I(inode)->i_data_sem);
+	ret = ext4_ext_remove_space(inode, le32_to_cpu(lrange.fc_lblk),
+				le32_to_cpu(lrange.fc_lblk) +
+				le32_to_cpu(lrange.fc_len) - 1);
+	up_write(&EXT4_I(inode)->i_data_sem);
 	if (ret)
-		jbd_debug(1, "ext4_punch_hole returned %d", ret);
+		goto out;
 	ext4_ext_replay_shrink_inode(inode,
 		i_size_read(inode) >> sb->s_blocksize_bits);
 	ext4_mark_inode_dirty(NULL, inode);
+out:
 	iput(inode);
-
 	return 0;
 }
 
@@ -1836,7 +1922,7 @@
 		inode = ext4_iget(sb, state->fc_modified_inodes[i],
 			EXT4_IGET_NORMAL);
 		if (IS_ERR(inode)) {
-			jbd_debug(1, "Inode %d not found.",
+			ext4_debug("Inode %d not found.",
 				state->fc_modified_inodes[i]);
 			continue;
 		}
@@ -1902,6 +1988,33 @@
 	kfree(sbi->s_fc_replay_state.fc_modified_inodes);
 }
 
+static bool ext4_fc_value_len_isvalid(struct ext4_sb_info *sbi,
+				      int tag, int len)
+{
+	switch (tag) {
+	case EXT4_FC_TAG_ADD_RANGE:
+		return len == sizeof(struct ext4_fc_add_range);
+	case EXT4_FC_TAG_DEL_RANGE:
+		return len == sizeof(struct ext4_fc_del_range);
+	case EXT4_FC_TAG_CREAT:
+	case EXT4_FC_TAG_LINK:
+	case EXT4_FC_TAG_UNLINK:
+		len -= sizeof(struct ext4_fc_dentry_info);
+		return len >= 1 && len <= EXT4_NAME_LEN;
+	case EXT4_FC_TAG_INODE:
+		len -= sizeof(struct ext4_fc_inode);
+		return len >= EXT4_GOOD_OLD_INODE_SIZE &&
+			len <= sbi->s_inode_size;
+	case EXT4_FC_TAG_PAD:
+		return true; /* padding can have any length */
+	case EXT4_FC_TAG_TAIL:
+		return len >= sizeof(struct ext4_fc_tail);
+	case EXT4_FC_TAG_HEAD:
+		return len == sizeof(struct ext4_fc_head);
+	}
+	return false;
+}
+
 /*
  * Recovery Scan phase handler
  *
@@ -1928,7 +2041,7 @@
 	struct ext4_fc_replay_state *state;
 	int ret = JBD2_FC_REPLAY_CONTINUE;
 	struct ext4_fc_add_range ext;
-	struct ext4_fc_tl tl;
+	struct ext4_fc_tl_mem tl;
 	struct ext4_fc_tail tail;
 	__u8 *start, *end, *cur, *val;
 	struct ext4_fc_head head;
@@ -1937,7 +2050,7 @@
 	state = &sbi->s_fc_replay_state;
 
 	start = (u8 *)bh->b_data;
-	end = (__u8 *)bh->b_data + journal->j_blocksize - 1;
+	end = start + journal->j_blocksize;
 
 	if (state->fc_replay_expected_off == 0) {
 		state->fc_cur_tag = 0;
@@ -1958,19 +2071,26 @@
 	}
 
 	state->fc_replay_expected_off++;
-	for (cur = start; cur < end; cur = cur + sizeof(tl) + le16_to_cpu(tl.fc_len)) {
-		memcpy(&tl, cur, sizeof(tl));
-		val = cur + sizeof(tl);
-		jbd_debug(3, "Scan phase, tag:%s, blk %lld\n",
-			  tag2str(le16_to_cpu(tl.fc_tag)), bh->b_blocknr);
-		switch (le16_to_cpu(tl.fc_tag)) {
+	for (cur = start; cur <= end - EXT4_FC_TAG_BASE_LEN;
+	     cur = cur + EXT4_FC_TAG_BASE_LEN + tl.fc_len) {
+		ext4_fc_get_tl(&tl, cur);
+		val = cur + EXT4_FC_TAG_BASE_LEN;
+		if (tl.fc_len > end - val ||
+		    !ext4_fc_value_len_isvalid(sbi, tl.fc_tag, tl.fc_len)) {
+			ret = state->fc_replay_num_tags ?
+				JBD2_FC_REPLAY_STOP : -ECANCELED;
+			goto out_err;
+		}
+		ext4_debug("Scan phase, tag:%s, blk %lld\n",
+			   tag2str(tl.fc_tag), bh->b_blocknr);
+		switch (tl.fc_tag) {
 		case EXT4_FC_TAG_ADD_RANGE:
 			memcpy(&ext, val, sizeof(ext));
 			ex = (struct ext4_extent *)&ext.fc_ex;
 			ret = ext4_fc_record_regions(sb,
 				le32_to_cpu(ext.fc_ino),
 				le32_to_cpu(ex->ee_block), ext4_ext_pblock(ex),
-				ext4_ext_get_actual_len(ex));
+				ext4_ext_get_actual_len(ex), 0);
 			if (ret < 0)
 				break;
 			ret = JBD2_FC_REPLAY_CONTINUE;
@@ -1983,13 +2103,13 @@
 		case EXT4_FC_TAG_PAD:
 			state->fc_cur_tag++;
 			state->fc_crc = ext4_chksum(sbi, state->fc_crc, cur,
-					sizeof(tl) + le16_to_cpu(tl.fc_len));
+				EXT4_FC_TAG_BASE_LEN + tl.fc_len);
 			break;
 		case EXT4_FC_TAG_TAIL:
 			state->fc_cur_tag++;
 			memcpy(&tail, val, sizeof(tail));
 			state->fc_crc = ext4_chksum(sbi, state->fc_crc, cur,
-						sizeof(tl) +
+						EXT4_FC_TAG_BASE_LEN +
 						offsetof(struct ext4_fc_tail,
 						fc_crc));
 			if (le32_to_cpu(tail.fc_tid) == expected_tid &&
@@ -2016,7 +2136,7 @@
 			}
 			state->fc_cur_tag++;
 			state->fc_crc = ext4_chksum(sbi, state->fc_crc, cur,
-					    sizeof(tl) + le16_to_cpu(tl.fc_len));
+				EXT4_FC_TAG_BASE_LEN + tl.fc_len);
 			break;
 		default:
 			ret = state->fc_replay_num_tags ?
@@ -2040,7 +2160,7 @@
 {
 	struct super_block *sb = journal->j_private;
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
-	struct ext4_fc_tl tl;
+	struct ext4_fc_tl_mem tl;
 	__u8 *start, *end, *cur, *val;
 	int ret = JBD2_FC_REPLAY_CONTINUE;
 	struct ext4_fc_replay_state *state = &sbi->s_fc_replay_state;
@@ -2056,7 +2176,7 @@
 		sbi->s_mount_state |= EXT4_FC_REPLAY;
 	}
 	if (!sbi->s_fc_replay_state.fc_replay_num_tags) {
-		jbd_debug(1, "Replay stops\n");
+		ext4_debug("Replay stops\n");
 		ext4_fc_set_bitmaps_and_counters(sb);
 		return 0;
 	}
@@ -2069,21 +2189,22 @@
 #endif
 
 	start = (u8 *)bh->b_data;
-	end = (__u8 *)bh->b_data + journal->j_blocksize - 1;
+	end = start + journal->j_blocksize;
 
-	for (cur = start; cur < end; cur = cur + sizeof(tl) + le16_to_cpu(tl.fc_len)) {
-		memcpy(&tl, cur, sizeof(tl));
-		val = cur + sizeof(tl);
+	for (cur = start; cur <= end - EXT4_FC_TAG_BASE_LEN;
+	     cur = cur + EXT4_FC_TAG_BASE_LEN + tl.fc_len) {
+		ext4_fc_get_tl(&tl, cur);
+		val = cur + EXT4_FC_TAG_BASE_LEN;
 
 		if (state->fc_replay_num_tags == 0) {
 			ret = JBD2_FC_REPLAY_STOP;
 			ext4_fc_set_bitmaps_and_counters(sb);
 			break;
 		}
-		jbd_debug(3, "Replay phase, tag:%s\n",
-				tag2str(le16_to_cpu(tl.fc_tag)));
+
+		ext4_debug("Replay phase, tag:%s\n", tag2str(tl.fc_tag));
 		state->fc_replay_num_tags--;
-		switch (le16_to_cpu(tl.fc_tag)) {
+		switch (tl.fc_tag) {
 		case EXT4_FC_TAG_LINK:
 			ret = ext4_fc_replay_link(sb, &tl, val);
 			break;
@@ -2104,19 +2225,18 @@
 			break;
 		case EXT4_FC_TAG_PAD:
 			trace_ext4_fc_replay(sb, EXT4_FC_TAG_PAD, 0,
-					     le16_to_cpu(tl.fc_len), 0);
+					     tl.fc_len, 0);
 			break;
 		case EXT4_FC_TAG_TAIL:
-			trace_ext4_fc_replay(sb, EXT4_FC_TAG_TAIL, 0,
-					     le16_to_cpu(tl.fc_len), 0);
+			trace_ext4_fc_replay(sb, EXT4_FC_TAG_TAIL,
+					     0, tl.fc_len, 0);
 			memcpy(&tail, val, sizeof(tail));
 			WARN_ON(le32_to_cpu(tail.fc_tid) != expected_tid);
 			break;
 		case EXT4_FC_TAG_HEAD:
 			break;
 		default:
-			trace_ext4_fc_replay(sb, le16_to_cpu(tl.fc_tag), 0,
-					     le16_to_cpu(tl.fc_len), 0);
+			trace_ext4_fc_replay(sb, tl.fc_tag, 0, tl.fc_len, 0);
 			ret = -ECANCELED;
 			break;
 		}
@@ -2140,17 +2260,17 @@
 	journal->j_fc_cleanup_callback = ext4_fc_cleanup;
 }
 
-static const char *fc_ineligible_reasons[] = {
-	"Extended attributes changed",
-	"Cross rename",
-	"Journal flag changed",
-	"Insufficient memory",
-	"Swap boot",
-	"Resize",
-	"Dir renamed",
-	"Falloc range op",
-	"Data journalling",
-	"FC Commit Failed"
+static const char * const fc_ineligible_reasons[] = {
+	[EXT4_FC_REASON_XATTR] = "Extended attributes changed",
+	[EXT4_FC_REASON_CROSS_RENAME] = "Cross rename",
+	[EXT4_FC_REASON_JOURNAL_FLAG_CHANGE] = "Journal flag changed",
+	[EXT4_FC_REASON_NOMEM] = "Insufficient memory",
+	[EXT4_FC_REASON_SWAP_BOOT] = "Swap boot",
+	[EXT4_FC_REASON_RESIZE] = "Resize",
+	[EXT4_FC_REASON_RENAME_DIR] = "Dir renamed",
+	[EXT4_FC_REASON_FALLOC_RANGE] = "Falloc range op",
+	[EXT4_FC_REASON_INODE_JOURNAL_DATA] = "Data journalling",
+	[EXT4_FC_REASON_ENCRYPTED_FILENAME] = "Encrypted filename",
 };
 
 int ext4_fc_info_show(struct seq_file *seq, void *v)
@@ -2166,7 +2286,7 @@
 		"fc stats:\n%ld commits\n%ld ineligible\n%ld numblks\n%lluus avg_commit_time\n",
 		   stats->fc_num_commits, stats->fc_ineligible_commits,
 		   stats->fc_numblks,
-		   div_u64(sbi->s_fc_avg_commit_time, 1000));
+		   div_u64(stats->s_fc_avg_commit_time, 1000));
 	seq_puts(seq, "Ineligible reasons:\n");
 	for (i = 0; i < EXT4_FC_REASON_MAX; i++)
 		seq_printf(seq, "\"%s\":\t%d\n", fc_ineligible_reasons[i],
@@ -2185,3 +2305,8 @@
 
 	return 0;
 }
+
+void ext4_fc_destroy_dentry_cache(void)
+{
+	kmem_cache_destroy(ext4_fc_dentry_cachep);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/fast_commit.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/fast_commit.h
@@ -58,7 +58,7 @@
 	__u8 fc_dname[0];
 };
 
-/* Value structure for EXT4_FC_TAG_INODE and EXT4_FC_TAG_INODE_PARTIAL. */
+/* Value structure for EXT4_FC_TAG_INODE. */
 struct ext4_fc_inode {
 	__le32 fc_ino;
 	__u8 fc_raw_inode[0];
@@ -70,22 +70,23 @@
 	__le32 fc_crc;
 };
 
+/* Tag base length */
+#define EXT4_FC_TAG_BASE_LEN (sizeof(struct ext4_fc_tl))
+
+/*
+ * Fast commit status codes
+ */
+enum {
+	EXT4_FC_STATUS_OK = 0,
+	EXT4_FC_STATUS_INELIGIBLE,
+	EXT4_FC_STATUS_SKIPPED,
+	EXT4_FC_STATUS_FAILED,
+};
+
 /*
- * Fast commit reason codes
+ * Fast commit ineligiblity reasons:
  */
 enum {
-	/*
-	 * Commit status codes:
-	 */
-	EXT4_FC_REASON_OK = 0,
-	EXT4_FC_REASON_INELIGIBLE,
-	EXT4_FC_REASON_ALREADY_COMMITTED,
-	EXT4_FC_REASON_FC_START_FAILED,
-	EXT4_FC_REASON_FC_FAILED,
-
-	/*
-	 * Fast commit ineligiblity reasons:
-	 */
 	EXT4_FC_REASON_XATTR = 0,
 	EXT4_FC_REASON_CROSS_RENAME,
 	EXT4_FC_REASON_JOURNAL_FLAG_CHANGE,
@@ -95,7 +96,7 @@
 	EXT4_FC_REASON_RENAME_DIR,
 	EXT4_FC_REASON_FALLOC_RANGE,
 	EXT4_FC_REASON_INODE_JOURNAL_DATA,
-	EXT4_FC_COMMIT_FAILED,
+	EXT4_FC_REASON_ENCRYPTED_FILENAME,
 	EXT4_FC_REASON_MAX
 };
 
@@ -117,7 +118,10 @@
 	unsigned int fc_ineligible_reason_count[EXT4_FC_REASON_MAX];
 	unsigned long fc_num_commits;
 	unsigned long fc_ineligible_commits;
+	unsigned long fc_failed_commits;
+	unsigned long fc_skipped_commits;
 	unsigned long fc_numblks;
+	u64 s_fc_avg_commit_time;
 };
 
 #define EXT4_FC_REPLAY_REALLOC_INCREMENT	4
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/file.c
@@ -74,7 +74,7 @@
 		return generic_file_read_iter(iocb, to);
 	}
 
-	ret = iomap_dio_rw(iocb, to, &ext4_iomap_ops, NULL, 0);
+	ret = iomap_dio_rw(iocb, to, &ext4_iomap_ops, NULL, 0, 0);
 	inode_unlock_shared(inode);
 
 	file_accessed(iocb->ki_filp);
@@ -259,7 +259,6 @@
 	if (iocb->ki_flags & IOCB_NOWAIT)
 		return -EOPNOTSUPP;
 
-	ext4_fc_start_update(inode);
 	inode_lock(inode);
 	ret = ext4_write_checks(iocb, from);
 	if (ret <= 0)
@@ -271,7 +270,6 @@
 
 out:
 	inode_unlock(inode);
-	ext4_fc_stop_update(inode);
 	if (likely(ret > 0)) {
 		iocb->ki_pos += ret;
 		ret = generic_write_sync(iocb, ret);
@@ -281,80 +279,38 @@
 }
 
 static ssize_t ext4_handle_inode_extension(struct inode *inode, loff_t offset,
-					   ssize_t written, size_t count)
+					   ssize_t count)
 {
 	handle_t *handle;
-	bool truncate = false;
-	u8 blkbits = inode->i_blkbits;
-	ext4_lblk_t written_blk, end_blk;
-	int ret;
-
-	/*
-	 * Note that EXT4_I(inode)->i_disksize can get extended up to
-	 * inode->i_size while the I/O was running due to writeback of delalloc
-	 * blocks. But, the code in ext4_iomap_alloc() is careful to use
-	 * zeroed/unwritten extents if this is possible; thus we won't leave
-	 * uninitialized blocks in a file even if we didn't succeed in writing
-	 * as much as we intended.
-	 */
-	WARN_ON_ONCE(i_size_read(inode) < EXT4_I(inode)->i_disksize);
-	if (offset + count <= EXT4_I(inode)->i_disksize) {
-		/*
-		 * We need to ensure that the inode is removed from the orphan
-		 * list if it has been added prematurely, due to writeback of
-		 * delalloc blocks.
-		 */
-		if (!list_empty(&EXT4_I(inode)->i_orphan) && inode->i_nlink) {
-			handle = ext4_journal_start(inode, EXT4_HT_INODE, 2);
-
-			if (IS_ERR(handle)) {
-				ext4_orphan_del(NULL, inode);
-				return PTR_ERR(handle);
-			}
-
-			ext4_orphan_del(handle, inode);
-			ext4_journal_stop(handle);
-		}
-
-		return written;
-	}
-
-	if (written < 0)
-		goto truncate;
 
+	lockdep_assert_held_write(&inode->i_rwsem);
 	handle = ext4_journal_start(inode, EXT4_HT_INODE, 2);
-	if (IS_ERR(handle)) {
-		written = PTR_ERR(handle);
-		goto truncate;
-	}
+	if (IS_ERR(handle))
+		return PTR_ERR(handle);
 
-	if (ext4_update_inode_size(inode, offset + written)) {
-		ret = ext4_mark_inode_dirty(handle, inode);
+	if (ext4_update_inode_size(inode, offset + count)) {
+		int ret = ext4_mark_inode_dirty(handle, inode);
 		if (unlikely(ret)) {
-			written = ret;
 			ext4_journal_stop(handle);
-			goto truncate;
+			return ret;
 		}
 	}
 
-	/*
-	 * We may need to truncate allocated but not written blocks beyond EOF.
-	 */
-	written_blk = ALIGN(offset + written, 1 << blkbits);
-	end_blk = ALIGN(offset + count, 1 << blkbits);
-	if (written_blk < end_blk && ext4_can_truncate(inode))
-		truncate = true;
-
-	/*
-	 * Remove the inode from the orphan list if it has been extended and
-	 * everything went OK.
-	 */
-	if (!truncate && inode->i_nlink)
+	if (inode->i_nlink)
 		ext4_orphan_del(handle, inode);
 	ext4_journal_stop(handle);
 
-	if (truncate) {
-truncate:
+	return count;
+}
+
+/*
+ * Clean up the inode after DIO or DAX extending write has completed and the
+ * inode size has been updated using ext4_handle_inode_extension().
+ */
+static void ext4_inode_extension_cleanup(struct inode *inode, bool need_trunc)
+{
+	lockdep_assert_held_write(&inode->i_rwsem);
+	if (need_trunc) {
 		ext4_truncate_failed_write(inode);
 		/*
 		 * If the truncate operation failed early, then the inode may
@@ -363,9 +319,29 @@
 		 */
 		if (inode->i_nlink)
 			ext4_orphan_del(NULL, inode);
+		return;
 	}
+	/*
+	 * If i_disksize got extended either due to writeback of delalloc
+	 * blocks or extending truncate while the DIO was running we could fail
+	 * to cleanup the orphan list in ext4_handle_inode_extension(). Do it
+	 * now.
+	 */
+	if (!list_empty(&EXT4_I(inode)->i_orphan) && inode->i_nlink) {
+		handle_t *handle = ext4_journal_start(inode, EXT4_HT_INODE, 2);
 
-	return written;
+		if (IS_ERR(handle)) {
+			/*
+			 * The write has successfully completed. Not much to
+			 * do with the error here so just cleanup the orphan
+			 * list and hope for the best.
+			 */
+			ext4_orphan_del(NULL, inode);
+			return;
+		}
+		ext4_orphan_del(handle, inode);
+		ext4_journal_stop(handle);
+	}
 }
 
 static int ext4_dio_write_end_io(struct kiocb *iocb, ssize_t size,
@@ -374,31 +350,23 @@
 	loff_t pos = iocb->ki_pos;
 	struct inode *inode = file_inode(iocb->ki_filp);
 
+	if (!error && size && flags & IOMAP_DIO_UNWRITTEN)
+		error = ext4_convert_unwritten_extents(NULL, inode, pos, size);
 	if (error)
 		return error;
-
-	if (size && flags & IOMAP_DIO_UNWRITTEN) {
-		error = ext4_convert_unwritten_extents(NULL, inode, pos, size);
-		if (error < 0)
-			return error;
-	}
 	/*
-	 * If we are extending the file, we have to update i_size here before
-	 * page cache gets invalidated in iomap_dio_rw(). Otherwise racing
-	 * buffered reads could zero out too much from page cache pages. Update
-	 * of on-disk size will happen later in ext4_dio_write_iter() where
-	 * we have enough information to also perform orphan list handling etc.
-	 * Note that we perform all extending writes synchronously under
-	 * i_rwsem held exclusively so i_size update is safe here in that case.
-	 * If the write was not extending, we cannot see pos > i_size here
-	 * because operations reducing i_size like truncate wait for all
-	 * outstanding DIO before updating i_size.
+	 * Note that EXT4_I(inode)->i_disksize can get extended up to
+	 * inode->i_size while the I/O was running due to writeback of delalloc
+	 * blocks. But the code in ext4_iomap_alloc() is careful to use
+	 * zeroed/unwritten extents if this is possible; thus we won't leave
+	 * uninitialized blocks in a file even if we didn't succeed in writing
+	 * as much as we intended. Also we can race with truncate or write
+	 * expanding the file so we have to be a bit careful here.
 	 */
-	pos += size;
-	if (pos > i_size_read(inode))
-		i_size_write(inode, pos);
-
-	return 0;
+	if (pos + size <= READ_ONCE(EXT4_I(inode)->i_disksize) &&
+	    pos + size <= i_size_read(inode))
+		return size;
+	return ext4_handle_inode_extension(inode, pos, size);
 }
 
 static const struct iomap_dio_ops ext4_dio_write_ops = {
@@ -528,6 +496,12 @@
 		ret = -EAGAIN;
 		goto out;
 	}
+	/*
+	 * Make sure inline data cannot be created anymore since we are going
+	 * to allocate blocks for DIO. We know the inode does not have any
+	 * inline data now because ext4_dio_supported() checked for that.
+	 */
+	ext4_clear_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
 
 	offset = iocb->ki_pos;
 	count = ret;
@@ -552,9 +526,7 @@
 			goto out;
 		}
 
-		ext4_fc_start_update(inode);
 		ret = ext4_orphan_add(handle, inode);
-		ext4_fc_stop_update(inode);
 		if (ret) {
 			ext4_journal_stop(handle);
 			goto out;
@@ -566,12 +538,20 @@
 	if (ilock_shared)
 		iomap_ops = &ext4_iomap_overwrite_ops;
 	ret = iomap_dio_rw(iocb, from, iomap_ops, &ext4_dio_write_ops,
-			   (unaligned_io || extend) ? IOMAP_DIO_FORCE_WAIT : 0);
+			   (unaligned_io || extend) ? IOMAP_DIO_FORCE_WAIT : 0,
+			   0);
 	if (ret == -ENOTBLK)
 		ret = 0;
-
-	if (extend)
-		ret = ext4_handle_inode_extension(inode, offset, ret, count);
+	if (extend) {
+		/*
+		 * We always perform extending DIO write synchronously so by
+		 * now the IO is completed and ext4_handle_inode_extension()
+		 * was called. Cleanup the inode in case of error or race with
+		 * writeback of delalloc blocks.
+		 */
+		WARN_ON_ONCE(ret == -EIOCBQUEUED);
+		ext4_inode_extension_cleanup(inode, ret < 0);
+	}
 
 out:
 	if (ilock_shared)
@@ -652,8 +632,10 @@
 
 	ret = dax_iomap_rw(iocb, from, &ext4_iomap_ops);
 
-	if (extend)
-		ret = ext4_handle_inode_extension(inode, offset, ret, count);
+	if (extend) {
+		ret = ext4_handle_inode_extension(inode, offset, ret);
+		ext4_inode_extension_cleanup(inode, ret < (ssize_t)count);
+	}
 out:
 	inode_unlock(inode);
 	if (ret > 0)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/fsmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/fsmap.c
@@ -185,6 +185,56 @@
 	return fmr->fmr_physical + fmr->fmr_length;
 }
 
+static int ext4_getfsmap_meta_helper(struct super_block *sb,
+				     ext4_group_t agno, ext4_grpblk_t start,
+				     ext4_grpblk_t len, void *priv)
+{
+	struct ext4_getfsmap_info *info = priv;
+	struct ext4_fsmap *p;
+	struct ext4_fsmap *tmp;
+	struct ext4_sb_info *sbi = EXT4_SB(sb);
+	ext4_fsblk_t fsb, fs_start, fs_end;
+	int error;
+
+	fs_start = fsb = (EXT4_C2B(sbi, start) +
+			  ext4_group_first_block_no(sb, agno));
+	fs_end = fs_start + EXT4_C2B(sbi, len);
+
+	/* Return relevant extents from the meta_list */
+	list_for_each_entry_safe(p, tmp, &info->gfi_meta_list, fmr_list) {
+		if (p->fmr_physical < info->gfi_next_fsblk) {
+			list_del(&p->fmr_list);
+			kfree(p);
+			continue;
+		}
+		if (p->fmr_physical <= fs_start ||
+		    p->fmr_physical + p->fmr_length <= fs_end) {
+			/* Emit the retained free extent record if present */
+			if (info->gfi_lastfree.fmr_owner) {
+				error = ext4_getfsmap_helper(sb, info,
+							&info->gfi_lastfree);
+				if (error)
+					return error;
+				info->gfi_lastfree.fmr_owner = 0;
+			}
+			error = ext4_getfsmap_helper(sb, info, p);
+			if (error)
+				return error;
+			fsb = p->fmr_physical + p->fmr_length;
+			if (info->gfi_next_fsblk < fsb)
+				info->gfi_next_fsblk = fsb;
+			list_del(&p->fmr_list);
+			kfree(p);
+			continue;
+		}
+	}
+	if (info->gfi_next_fsblk < fsb)
+		info->gfi_next_fsblk = fsb;
+
+	return 0;
+}
+
+
 /* Transform a blockgroup's free record into a fsmap */
 static int ext4_getfsmap_datadev_helper(struct super_block *sb,
 					ext4_group_t agno, ext4_grpblk_t start,
@@ -486,6 +536,8 @@
 		keys[0].fmr_physical = bofs;
 	if (keys[1].fmr_physical >= eofs)
 		keys[1].fmr_physical = eofs - 1;
+	if (keys[1].fmr_physical < keys[0].fmr_physical)
+		return 0;
 	start_fsb = keys[0].fmr_physical;
 	end_fsb = keys[1].fmr_physical;
 
@@ -537,6 +589,7 @@
 		error = ext4_mballoc_query_range(sb, info->gfi_agno,
 				EXT4_B2C(sbi, info->gfi_low.fmr_physical),
 				EXT4_B2C(sbi, info->gfi_high.fmr_physical),
+				ext4_getfsmap_meta_helper,
 				ext4_getfsmap_datadev_helper, info);
 		if (error)
 			goto err;
@@ -558,7 +611,8 @@
 
 	/* Report any gaps at the end of the bg */
 	info->gfi_last = true;
-	error = ext4_getfsmap_datadev_helper(sb, end_ag, last_cluster, 0, info);
+	error = ext4_getfsmap_datadev_helper(sb, end_ag, last_cluster + 1,
+					     0, info);
 	if (error)
 		goto err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/hash.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/hash.c
@@ -277,7 +277,11 @@
 	}
 	default:
 		hinfo->hash = 0;
-		return -1;
+		hinfo->minor_hash = 0;
+		ext4_warning(dir->i_sb,
+			     "invalid/unsupported hash tree version %u",
+			     hinfo->hash_version);
+		return -EINVAL;
 	}
 	hash = hash & ~1;
 	if (hash == (EXT4_HTREE_EOF_32BIT << 1))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/ialloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/ialloc.c
@@ -91,7 +91,7 @@
 
 	if (buffer_verified(bh))
 		return 0;
-	if (EXT4_MB_GRP_IBITMAP_CORRUPT(grp))
+	if (!grp || EXT4_MB_GRP_IBITMAP_CORRUPT(grp))
 		return -EFSCORRUPTED;
 
 	ext4_lock_group(sb, block_group);
@@ -293,7 +293,7 @@
 	}
 	if (!(sbi->s_mount_state & EXT4_FC_REPLAY)) {
 		grp = ext4_get_group_info(sb, block_group);
-		if (unlikely(EXT4_MB_GRP_IBITMAP_CORRUPT(grp))) {
+		if (!grp || unlikely(EXT4_MB_GRP_IBITMAP_CORRUPT(grp))) {
 			fatal = -EFSCORRUPTED;
 			goto error_return;
 		}
@@ -510,11 +510,13 @@
 		goto fallback;
 	}
 
-	max_dirs = ndirs / ngroups + inodes_per_group / 16;
+	max_dirs = ndirs / ngroups + inodes_per_group*flex_size / 16;
 	min_inodes = avefreei - inodes_per_group*flex_size / 4;
 	if (min_inodes < 1)
 		min_inodes = 1;
 	min_clusters = avefreec - EXT4_CLUSTERS_PER_GROUP(sb)*flex_size / 4;
+	if (min_clusters < 0)
+		min_clusters = 0;
 
 	/*
 	 * Start looking in the flex group where we last allocated an
@@ -756,10 +758,10 @@
 	struct ext4_group_desc *gdp;
 	ext4_group_t group;
 	int bit;
-	int err = -EFSCORRUPTED;
+	int err;
 
 	if (ino < EXT4_FIRST_INO(sb) || ino > max_ino)
-		goto out;
+		return -EFSCORRUPTED;
 
 	group = (ino - 1) / EXT4_INODES_PER_GROUP(sb);
 	bit = (ino - 1) % EXT4_INODES_PER_GROUP(sb);
@@ -862,6 +864,7 @@
 	err = ext4_handle_dirty_metadata(NULL, NULL, group_desc_bh);
 	sync_dirty_buffer(group_desc_bh);
 out:
+	brelse(inode_bitmap_bh);
 	return err;
 }
 
@@ -1048,19 +1051,20 @@
 			 * Skip groups with already-known suspicious inode
 			 * tables
 			 */
-			if (EXT4_MB_GRP_IBITMAP_CORRUPT(grp))
+			if (!grp || EXT4_MB_GRP_IBITMAP_CORRUPT(grp))
 				goto next_group;
 		}
 
 		brelse(inode_bitmap_bh);
 		inode_bitmap_bh = ext4_read_inode_bitmap(sb, group);
 		/* Skip groups with suspicious inode tables */
-		if (((!(sbi->s_mount_state & EXT4_FC_REPLAY))
-		     && EXT4_MB_GRP_IBITMAP_CORRUPT(grp)) ||
-		    IS_ERR(inode_bitmap_bh)) {
+		if (IS_ERR(inode_bitmap_bh)) {
 			inode_bitmap_bh = NULL;
 			goto next_group;
 		}
+		if (!(sbi->s_mount_state & EXT4_FC_REPLAY) &&
+		    EXT4_MB_GRP_IBITMAP_CORRUPT(grp))
+			goto next_group;
 
 repeat_in_this_group:
 		ret2 = find_inode_bit(sb, group, inode_bitmap_bh, &ino);
@@ -1186,6 +1190,10 @@
 
 		if (!(sbi->s_mount_state & EXT4_FC_REPLAY)) {
 			grp = ext4_get_group_info(sb, group);
+			if (!grp) {
+				err = -EFSCORRUPTED;
+				goto out;
+			}
 			down_read(&grp->alloc_sem); /*
 						     * protect vs itable
 						     * lazyinit
@@ -1529,7 +1537,7 @@
 	}
 
 	gdp = ext4_get_group_desc(sb, group, &group_desc_bh);
-	if (!gdp)
+	if (!gdp || !grp)
 		goto out;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/indirect.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/indirect.c
@@ -148,6 +148,7 @@
 	struct super_block *sb = inode->i_sb;
 	Indirect *p = chain;
 	struct buffer_head *bh;
+	unsigned int key;
 	int ret = -EIO;
 
 	*err = 0;
@@ -156,7 +157,13 @@
 	if (!p->key)
 		goto no_block;
 	while (--depth) {
-		bh = sb_getblk(sb, le32_to_cpu(p->key));
+		key = le32_to_cpu(p->key);
+		if (key > ext4_blocks_count(EXT4_SB(sb)->s_es)) {
+			/* the block was out of range */
+			ret = -EFSCORRUPTED;
+			goto failure;
+		}
+		bh = sb_getblk(sb, key);
 		if (unlikely(!bh)) {
 			ret = -ENOMEM;
 			goto failure;
@@ -460,7 +467,7 @@
 		 * the new i_size.  But that is not done here - it is done in
 		 * generic_commit_write->__mark_inode_dirty->ext4_dirty_inode.
 		 */
-		jbd_debug(5, "splicing indirect only\n");
+		ext4_debug("splicing indirect only\n");
 		BUFFER_TRACE(where->bh, "call ext4_handle_dirty_metadata");
 		err = ext4_handle_dirty_metadata(handle, ar->inode, where->bh);
 		if (err)
@@ -472,7 +479,7 @@
 		err = ext4_mark_inode_dirty(handle, ar->inode);
 		if (unlikely(err))
 			goto err_out;
-		jbd_debug(5, "splicing direct\n");
+		ext4_debug("splicing direct\n");
 	}
 	return err;
 
@@ -644,6 +651,14 @@
 
 	ext4_update_inode_fsync_trans(handle, inode, 1);
 	count = ar.len;
+
+	/*
+	 * Update reserved blocks/metadata blocks after successful block
+	 * allocation which had been deferred till now.
+	 */
+	if (flags & EXT4_GET_BLOCKS_DELALLOC_RESERVE)
+		ext4_da_update_reserve_space(inode, count, 1);
+
 got_it:
 	map->m_flags |= EXT4_MAP_MAPPED;
 	map->m_pblk = le32_to_cpu(chain[depth-1].key);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/inline.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/inline.c
@@ -33,8 +33,12 @@
 	struct ext4_xattr_ibody_header *header;
 	struct ext4_xattr_entry *entry;
 	struct ext4_inode *raw_inode;
+	void *end;
 	int free, min_offs;
 
+	if (!EXT4_INODE_HAS_XATTR_SPACE(inode))
+		return 0;
+
 	min_offs = EXT4_SB(inode->i_sb)->s_inode_size -
 			EXT4_GOOD_OLD_INODE_SIZE -
 			EXT4_I(inode)->i_extra_isize -
@@ -53,14 +57,23 @@
 	raw_inode = ext4_raw_inode(iloc);
 	header = IHDR(inode, raw_inode);
 	entry = IFIRST(header);
+	end = (void *)raw_inode + EXT4_SB(inode->i_sb)->s_inode_size;
 
 	/* Compute min_offs. */
-	for (; !IS_LAST_ENTRY(entry); entry = EXT4_XATTR_NEXT(entry)) {
+	while (!IS_LAST_ENTRY(entry)) {
+		void *next = EXT4_XATTR_NEXT(entry);
+
+		if (next >= end) {
+			EXT4_ERROR_INODE(inode,
+					 "corrupt xattr in inline inode");
+			return 0;
+		}
 		if (!entry->e_value_inum && entry->e_value_size) {
 			size_t offs = le16_to_cpu(entry->e_value_offs);
 			if (offs < min_offs)
 				min_offs = offs;
 		}
+		entry = next;
 	}
 	free = min_offs -
 		((void *)entry - (void *)IFIRST(header)) - sizeof(__u32);
@@ -155,7 +168,6 @@
 					(void *)ext4_raw_inode(&is.iloc));
 		EXT4_I(inode)->i_inline_size = EXT4_MIN_INLINE_DATA_SIZE +
 				le32_to_cpu(is.s.here->e_value_size);
-		ext4_set_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
 	}
 out:
 	brelse(is.iloc.bh);
@@ -348,7 +360,7 @@
 
 	error = ext4_xattr_ibody_get(inode, i.name_index, i.name,
 				     value, len);
-	if (error == -ENODATA)
+	if (error < 0)
 		goto out;
 
 	BUFFER_TRACE(is.iloc.bh, "get_write_access");
@@ -1133,7 +1145,15 @@
 				     struct ext4_iloc *iloc,
 				     void *buf, int inline_size)
 {
-	ext4_create_inline_data(handle, inode, inline_size);
+	int ret;
+
+	ret = ext4_create_inline_data(handle, inode, inline_size);
+	if (ret) {
+		ext4_msg(inode->i_sb, KERN_EMERG,
+			"error restoring inline_data for inode -- potential data loss! (inode %lu, error %d)",
+			inode->i_ino, ret);
+		return;
+	}
 	ext4_write_inline_data(inode, iloc, buf, 0, inline_size);
 	ext4_set_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
 }
@@ -1175,6 +1195,7 @@
 		ext4_initialize_dirent_tail(dir_block,
 					    inode->i_sb->s_blocksize);
 	set_buffer_uptodate(dir_block);
+	unlock_buffer(dir_block);
 	err = ext4_handle_dirty_dirblock(handle, inode, dir_block);
 	if (err)
 		return err;
@@ -1249,6 +1270,7 @@
 	if (!S_ISDIR(inode->i_mode)) {
 		memcpy(data_bh->b_data, buf, inline_size);
 		set_buffer_uptodate(data_bh);
+		unlock_buffer(data_bh);
 		error = ext4_handle_dirty_metadata(handle,
 						   inode, data_bh);
 	} else {
@@ -1256,7 +1278,6 @@
 						       buf, inline_size);
 	}
 
-	unlock_buffer(data_bh);
 out_restore:
 	if (error)
 		ext4_restore_inline_data(handle, inode, iloc, buf, inline_size);
@@ -1425,7 +1446,11 @@
 			hinfo->hash = EXT4_DIRENT_HASH(de);
 			hinfo->minor_hash = EXT4_DIRENT_MINOR_HASH(de);
 		} else {
-			ext4fs_dirhash(dir, de->name, de->name_len, hinfo);
+			err = ext4fs_dirhash(dir, de->name, de->name_len, hinfo);
+			if (err) {
+				ret = err;
+				goto out;
+			}
 		}
 		if ((hinfo->hash < start_hash) ||
 		    ((hinfo->hash == start_hash) &&
@@ -1646,24 +1671,36 @@
 					struct ext4_dir_entry_2 **res_dir,
 					int *has_inline_data)
 {
+	struct ext4_xattr_ibody_find is = {
+		.s = { .not_found = -ENODATA, },
+	};
+	struct ext4_xattr_info i = {
+		.name_index = EXT4_XATTR_INDEX_SYSTEM,
+		.name = EXT4_XATTR_SYSTEM_DATA,
+	};
 	int ret;
-	struct ext4_iloc iloc;
 	void *inline_start;
 	int inline_size;
 
-	if (ext4_get_inode_loc(dir, &iloc))
-		return NULL;
+	ret = ext4_get_inode_loc(dir, &is.iloc);
+	if (ret)
+		return ERR_PTR(ret);
 
 	down_read(&EXT4_I(dir)->xattr_sem);
+
+	ret = ext4_xattr_ibody_find(dir, &i, &is);
+	if (ret)
+		goto out;
+
 	if (!ext4_has_inline_data(dir)) {
 		*has_inline_data = 0;
 		goto out;
 	}
 
-	inline_start = (void *)ext4_raw_inode(&iloc)->i_block +
+	inline_start = (void *)ext4_raw_inode(&is.iloc)->i_block +
 						EXT4_INLINE_DOTDOT_SIZE;
 	inline_size = EXT4_MIN_INLINE_DATA_SIZE - EXT4_INLINE_DOTDOT_SIZE;
-	ret = ext4_search_dir(iloc.bh, inline_start, inline_size,
+	ret = ext4_search_dir(is.iloc.bh, inline_start, inline_size,
 			      dir, fname, 0, res_dir);
 	if (ret == 1)
 		goto out_find;
@@ -1673,20 +1710,23 @@
 	if (ext4_get_inline_size(dir) == EXT4_MIN_INLINE_DATA_SIZE)
 		goto out;
 
-	inline_start = ext4_get_inline_xattr_pos(dir, &iloc);
+	inline_start = ext4_get_inline_xattr_pos(dir, &is.iloc);
 	inline_size = ext4_get_inline_size(dir) - EXT4_MIN_INLINE_DATA_SIZE;
 
-	ret = ext4_search_dir(iloc.bh, inline_start, inline_size,
+	ret = ext4_search_dir(is.iloc.bh, inline_start, inline_size,
 			      dir, fname, 0, res_dir);
 	if (ret == 1)
 		goto out_find;
 
 out:
-	brelse(iloc.bh);
-	iloc.bh = NULL;
+	brelse(is.iloc.bh);
+	if (ret < 0)
+		is.iloc.bh = ERR_PTR(ret);
+	else
+		is.iloc.bh = NULL;
 out_find:
 	up_read(&EXT4_I(dir)->xattr_sem);
-	return iloc.bh;
+	return is.iloc.bh;
 }
 
 int ext4_delete_inline_entry(handle_t *handle,
@@ -1780,19 +1820,20 @@
 	void *inline_pos;
 	unsigned int offset;
 	struct ext4_dir_entry_2 *de;
-	bool ret = true;
+	bool ret = false;
 
 	err = ext4_get_inode_loc(dir, &iloc);
 	if (err) {
 		EXT4_ERROR_INODE_ERR(dir, -err,
 				     "error %d getting inode %lu block",
 				     err, dir->i_ino);
-		return true;
+		return false;
 	}
 
 	down_read(&EXT4_I(dir)->xattr_sem);
 	if (!ext4_has_inline_data(dir)) {
 		*has_inline_data = 0;
+		ret = true;
 		goto out;
 	}
 
@@ -1801,7 +1842,6 @@
 		ext4_warning(dir->i_sb,
 			     "bad inline directory (dir #%lu) - no `..'",
 			     dir->i_ino);
-		ret = true;
 		goto out;
 	}
 
@@ -1820,16 +1860,15 @@
 				     dir->i_ino, le32_to_cpu(de->inode),
 				     le16_to_cpu(de->rec_len), de->name_len,
 				     inline_size);
-			ret = true;
 			goto out;
 		}
 		if (le32_to_cpu(de->inode)) {
-			ret = false;
 			goto out;
 		}
 		offset += ext4_rec_len_from_disk(de->rec_len, inline_size);
 	}
 
+	ret = true;
 out:
 	up_read(&EXT4_I(dir)->xattr_sem);
 	brelse(iloc.bh);
@@ -2004,6 +2043,18 @@
 	if (!ext4_has_inline_data(inode)) {
 		ext4_clear_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
 		return 0;
+	} else if (!ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA)) {
+		/*
+		 * Inode has inline data but EXT4_STATE_MAY_INLINE_DATA is
+		 * cleared. This means we are in the middle of moving of
+		 * inline data to delay allocated block. Just force writeout
+		 * here to finish conversion.
+		 */
+		error = filemap_flush(inode->i_mapping);
+		if (error)
+			return error;
+		if (!ext4_has_inline_data(inode))
+			return 0;
 	}
 
 	needed_blocks = ext4_writepage_trans_blocks(inode);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/inode.c
@@ -179,6 +179,8 @@
 
 	trace_ext4_evict_inode(inode);
 
+	if (EXT4_I(inode)->i_flags & EXT4_EA_INODE_FL)
+		ext4_evict_ea_inode(inode);
 	if (inode->i_nlink) {
 		/*
 		 * When journalling data dirty buffers are tracked only in the
@@ -223,13 +225,13 @@
 
 	/*
 	 * For inodes with journalled data, transaction commit could have
-	 * dirtied the inode. Flush worker is ignoring it because of I_FREEING
-	 * flag but we still need to remove the inode from the writeback lists.
+	 * dirtied the inode. And for inodes with dioread_nolock, unwritten
+	 * extents converting worker could merge extents and also have dirtied
+	 * the inode. Flush worker is ignoring it because of I_FREEING flag but
+	 * we still need to remove the inode from the writeback lists.
 	 */
-	if (!list_empty_careful(&inode->i_io_list)) {
-		WARN_ON_ONCE(!ext4_should_journal_data(inode));
+	if (!list_empty_careful(&inode->i_io_list))
 		inode_io_list_del(inode);
-	}
 
 	/*
 	 * Protect us against freezing - iput() caller didn't have to have any
@@ -336,8 +338,14 @@
 	ext4_xattr_inode_array_free(ea_inode_array);
 	return;
 no_delete:
+	/*
+	 * Check out some where else accidentally dirty the evicting inode,
+	 * which may probably cause inode use-after-free issues later.
+	 */
+	WARN_ON_ONCE(!list_empty_careful(&inode->i_io_list));
+
 	if (!list_empty(&EXT4_I(inode)->i_fc_list))
-		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_NOMEM);
+		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_NOMEM, NULL);
 	ext4_clear_inode(inode);	/* We must guarantee clearing of inode... */
 }
 
@@ -476,6 +484,35 @@
 }
 #endif /* ES_AGGRESSIVE_TEST */
 
+static int ext4_map_query_blocks(handle_t *handle, struct inode *inode,
+				 struct ext4_map_blocks *map)
+{
+	unsigned int status;
+	int retval;
+
+	if (ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS))
+		retval = ext4_ext_map_blocks(handle, inode, map, 0);
+	else
+		retval = ext4_ind_map_blocks(handle, inode, map, 0);
+
+	if (retval <= 0)
+		return retval;
+
+	if (unlikely(retval != map->m_len)) {
+		ext4_warning(inode->i_sb,
+			     "ES len assertion failed for inode "
+			     "%lu: retval %d != map->m_len %d",
+			     inode->i_ino, retval, map->m_len);
+		WARN_ON(1);
+	}
+
+	status = map->m_flags & EXT4_MAP_UNWRITTEN ?
+			EXTENT_STATUS_UNWRITTEN : EXTENT_STATUS_WRITTEN;
+	ext4_es_insert_extent(inode, map->m_lblk, map->m_len,
+			      map->m_pblk, status);
+	return retval;
+}
+
 /*
  * The ext4_map_blocks() function tries to look up the requested blocks,
  * and returns if the blocks are already mapped.
@@ -581,10 +618,8 @@
 		    ext4_es_scan_range(inode, &ext4_es_is_delayed, map->m_lblk,
 				       map->m_lblk + map->m_len - 1))
 			status |= EXTENT_STATUS_DELAYED;
-		ret = ext4_es_insert_extent(inode, map->m_lblk,
-					    map->m_len, map->m_pblk, status);
-		if (ret < 0)
-			retval = ret;
+		ext4_es_insert_extent(inode, map->m_lblk, map->m_len,
+				      map->m_pblk, status);
 	}
 	up_read((&EXT4_I(inode)->i_data_sem));
 
@@ -646,16 +681,6 @@
 			 */
 			ext4_clear_inode_state(inode, EXT4_STATE_EXT_MIGRATE);
 		}
-
-		/*
-		 * Update reserved blocks/metadata blocks after successful
-		 * block allocation which had been deferred till now. We don't
-		 * support fallocate for non extent files. So we can update
-		 * reserve space here.
-		 */
-		if ((retval > 0) &&
-			(flags & EXT4_GET_BLOCKS_DELALLOC_RESERVE))
-			ext4_da_update_reserve_space(inode, retval, 1);
 	}
 
 	if (retval > 0) {
@@ -703,12 +728,8 @@
 		    ext4_es_scan_range(inode, &ext4_es_is_delayed, map->m_lblk,
 				       map->m_lblk + map->m_len - 1))
 			status |= EXTENT_STATUS_DELAYED;
-		ret = ext4_es_insert_extent(inode, map->m_lblk, map->m_len,
-					    map->m_pblk, status);
-		if (ret < 0) {
-			retval = ret;
-			goto out_sem;
-		}
+		ext4_es_insert_extent(inode, map->m_lblk, map->m_len,
+				      map->m_pblk, status);
 	}
 
 out_sem:
@@ -741,10 +762,11 @@
 			if (ret)
 				return ret;
 		}
-		ext4_fc_track_range(handle, inode, map->m_lblk,
-			    map->m_lblk + map->m_len - 1);
 	}
-
+	if (retval > 0 && (map->m_flags & EXT4_MAP_UNWRITTEN ||
+				map->m_flags & EXT4_MAP_MAPPED))
+		ext4_fc_track_range(handle, inode, map->m_lblk,
+					map->m_lblk + map->m_len - 1);
 	if (retval < 0)
 		ext_debug(inode, "failed with err %d\n", retval);
 	return retval;
@@ -1174,6 +1196,13 @@
 	page = grab_cache_page_write_begin(mapping, index, flags);
 	if (!page)
 		return -ENOMEM;
+	/*
+	 * The same as page allocation, we prealloc buffer heads before
+	 * starting the handle.
+	 */
+	if (!page_has_buffers(page))
+		create_empty_buffers(page, inode->i_sb->s_blocksize, 0);
+
 	unlock_page(page);
 
 retry_journal:
@@ -1288,7 +1317,8 @@
 
 	trace_ext4_write_end(inode, pos, len, copied);
 
-	if (ext4_has_inline_data(inode))
+	if (ext4_has_inline_data(inode) &&
+	    ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA))
 		return ext4_write_inline_data_end(inode, pos, len, copied, page);
 
 	copied = block_write_end(file, mapping, pos, len, copied, page, fsdata);
@@ -1559,7 +1589,14 @@
 		ext4_lblk_t start, last;
 		start = index << (PAGE_SHIFT - inode->i_blkbits);
 		last = end << (PAGE_SHIFT - inode->i_blkbits);
+
+		/*
+		 * avoid racing with extent status tree scans made by
+		 * ext4_insert_delayed_block()
+		 */
+		down_write(&EXT4_I(inode)->i_data_sem);
 		ext4_es_remove_extent(inode, start, last - start + 1);
+		up_write(&EXT4_I(inode)->i_data_sem);
 	}
 
 	pagevec_init(&pvec);
@@ -1704,23 +1741,18 @@
 
 	/* Lookup extent status tree firstly */
 	if (ext4_es_lookup_extent(inode, iblock, NULL, &es)) {
-		if (ext4_es_is_hole(&es)) {
-			retval = 0;
-			down_read(&EXT4_I(inode)->i_data_sem);
+		if (ext4_es_is_hole(&es))
 			goto add_delayed;
-		}
 
+found:
 		/*
-		 * the buffer head associated with a delayed and not unwritten
-		 * block found in the extent status cache must contain an
-		 * invalid block number and have its BH_New and BH_Delay bits
-		 * set, reflecting the state assigned when the block was
-		 * initially delayed allocated
+		 * Delayed extent could be allocated by fallocate.
+		 * So we need to check it.
 		 */
-		if (ext4_es_is_delonly(&es)) {
-			BUG_ON(bh->b_blocknr != invalid_block);
-			BUG_ON(!buffer_new(bh));
-			BUG_ON(!buffer_delay(bh));
+		if (ext4_es_is_delayed(&es) && !ext4_es_is_unwritten(&es)) {
+			map_bh(bh, inode->i_sb, invalid_block);
+			set_buffer_new(bh);
+			set_buffer_delay(bh);
 			return 0;
 		}
 
@@ -1749,52 +1781,42 @@
 	down_read(&EXT4_I(inode)->i_data_sem);
 	if (ext4_has_inline_data(inode))
 		retval = 0;
-	else if (ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS))
-		retval = ext4_ext_map_blocks(NULL, inode, map, 0);
 	else
-		retval = ext4_ind_map_blocks(NULL, inode, map, 0);
+		retval = ext4_map_query_blocks(NULL, inode, map);
+	up_read(&EXT4_I(inode)->i_data_sem);
+	if (retval)
+		return retval;
 
 add_delayed:
-	if (retval == 0) {
-		int ret;
-
-		/*
-		 * XXX: __block_prepare_write() unmaps passed block,
-		 * is it OK?
-		 */
-
-		ret = ext4_insert_delayed_block(inode, map->m_lblk);
-		if (ret != 0) {
-			retval = ret;
-			goto out_unlock;
+	down_write(&EXT4_I(inode)->i_data_sem);
+	/*
+	 * Page fault path (ext4_page_mkwrite does not take i_rwsem)
+	 * and fallocate path (no folio lock) can race. Make sure we
+	 * lookup the extent status tree here again while i_data_sem
+	 * is held in write mode, before inserting a new da entry in
+	 * the extent status tree.
+	 */
+	if (ext4_es_lookup_extent(inode, iblock, NULL, &es)) {
+		if (!ext4_es_is_hole(&es)) {
+			up_write(&EXT4_I(inode)->i_data_sem);
+			goto found;
 		}
-
-		map_bh(bh, inode->i_sb, invalid_block);
-		set_buffer_new(bh);
-		set_buffer_delay(bh);
-	} else if (retval > 0) {
-		int ret;
-		unsigned int status;
-
-		if (unlikely(retval != map->m_len)) {
-			ext4_warning(inode->i_sb,
-				     "ES len assertion failed for inode "
-				     "%lu: retval %d != map->m_len %d",
-				     inode->i_ino, retval, map->m_len);
-			WARN_ON(1);
+	} else if (!ext4_has_inline_data(inode)) {
+		retval = ext4_map_query_blocks(NULL, inode, map);
+		if (retval) {
+			up_write(&EXT4_I(inode)->i_data_sem);
+			return retval;
 		}
-
-		status = map->m_flags & EXT4_MAP_UNWRITTEN ?
-				EXTENT_STATUS_UNWRITTEN : EXTENT_STATUS_WRITTEN;
-		ret = ext4_es_insert_extent(inode, map->m_lblk, map->m_len,
-					    map->m_pblk, status);
-		if (ret != 0)
-			retval = ret;
 	}
 
-out_unlock:
-	up_read((&EXT4_I(inode)->i_data_sem));
+	retval = ext4_insert_delayed_block(inode, map->m_lblk);
+	up_write(&EXT4_I(inode)->i_data_sem);
+	if (retval)
+		return retval;
 
+	map_bh(bh, inode->i_sb, invalid_block);
+	set_buffer_new(bh);
+	set_buffer_delay(bh);
 	return retval;
 }
 
@@ -1847,30 +1869,16 @@
 	return 0;
 }
 
-static int bget_one(handle_t *handle, struct inode *inode,
-		    struct buffer_head *bh)
-{
-	get_bh(bh);
-	return 0;
-}
-
-static int bput_one(handle_t *handle, struct inode *inode,
-		    struct buffer_head *bh)
-{
-	put_bh(bh);
-	return 0;
-}
-
 static int __ext4_journalled_writepage(struct page *page,
 				       unsigned int len)
 {
 	struct address_space *mapping = page->mapping;
 	struct inode *inode = mapping->host;
-	struct buffer_head *page_bufs = NULL;
 	handle_t *handle = NULL;
 	int ret = 0, err = 0;
 	int inline_data = ext4_has_inline_data(inode);
 	struct buffer_head *inode_bh = NULL;
+	loff_t size;
 
 	ClearPageChecked(page);
 
@@ -1880,14 +1888,6 @@
 		inode_bh = ext4_journalled_write_inline_data(inode, len, page);
 		if (inode_bh == NULL)
 			goto out;
-	} else {
-		page_bufs = page_buffers(page);
-		if (!page_bufs) {
-			BUG();
-			goto out;
-		}
-		ext4_walk_page_buffers(handle, inode, page_bufs, 0, len,
-				       NULL, bget_one);
 	}
 	/*
 	 * We need to release the page lock before we start the
@@ -1908,7 +1908,8 @@
 
 	lock_page(page);
 	put_page(page);
-	if (page->mapping != mapping) {
+	size = i_size_read(inode);
+	if (page->mapping != mapping || page_offset(page) > size) {
 		/* The page got truncated from under us */
 		ext4_journal_stop(handle);
 		ret = 0;
@@ -1918,6 +1919,13 @@
 	if (inline_data) {
 		ret = ext4_mark_inode_dirty(handle, inode);
 	} else {
+		struct buffer_head *page_bufs = page_buffers(page);
+
+		if (page->index == size >> PAGE_SHIFT)
+			len = size & ~PAGE_MASK;
+		else
+			len = PAGE_SIZE;
+
 		ret = ext4_walk_page_buffers(handle, inode, page_bufs, 0, len,
 					     NULL, do_journal_get_write_access);
 
@@ -1938,9 +1946,6 @@
 out:
 	unlock_page(page);
 out_no_pagelock:
-	if (!inline_data && page_bufs)
-		ext4_walk_page_buffers(NULL, inode, page_bufs, 0, len,
-				       NULL, bput_one);
 	brelse(inode_bh);
 	return ret;
 }
@@ -2011,6 +2016,15 @@
 	else
 		len = PAGE_SIZE;
 
+	/* Should never happen but for bugs in other kernel subsystems */
+	if (!page_has_buffers(page)) {
+		ext4_warning_inode(inode,
+		   "page %lu does not have buffers attached", page->index);
+		ClearPageDirty(page);
+		unlock_page(page);
+		return 0;
+	}
+
 	page_bufs = page_buffers(page);
 	/*
 	 * We cannot do block allocation or other extent handling in this
@@ -2614,6 +2628,22 @@
 			wait_on_page_writeback(page);
 			BUG_ON(PageWriteback(page));
 
+			/*
+			 * Should never happen but for buggy code in
+			 * other subsystems that call
+			 * set_page_dirty() without properly warning
+			 * the file system first.  See [1] for more
+			 * information.
+			 *
+			 * [1] https://lore.kernel.org/linux-mm/20180103100430.GE4911@quack2.suse.cz
+			 */
+			if (!page_has_buffers(page)) {
+				ext4_warning_inode(mpd->inode, "page %lu does not have buffers attached", page->index);
+				ClearPageDirty(page);
+				unlock_page(page);
+				continue;
+			}
+
 			if (mpd->map.m_len == 0)
 				mpd->first_page = page->index;
 			mpd->next_page = page->index + 1;
@@ -3036,6 +3066,9 @@
 	    ext4_has_inline_data(inode))
 		return ext4_write_inline_data_end(inode, pos, len, copied, page);
 
+	if (unlikely(copied < len) && !PageUptodate(page))
+		copied = 0;
+
 	start = pos & (PAGE_SIZE - 1);
 	end = start + copied - 1;
 
@@ -3124,13 +3157,15 @@
 {
 	struct inode *inode = mapping->host;
 	journal_t *journal;
+	sector_t ret = 0;
 	int err;
 
+	inode_lock_shared(inode);
 	/*
 	 * We can get here for an inline file via the FIBMAP ioctl
 	 */
 	if (ext4_has_inline_data(inode))
-		return 0;
+		goto out;
 
 	if (mapping_tagged(mapping, PAGECACHE_TAG_DIRTY) &&
 			test_opt(inode->i_sb, DELALLOC)) {
@@ -3169,10 +3204,14 @@
 		jbd2_journal_unlock_updates(journal);
 
 		if (err)
-			return 0;
+			goto out;
 	}
 
-	return iomap_bmap(mapping, block, &ext4_iomap_ops);
+	ret = iomap_bmap(mapping, block, &ext4_iomap_ops);
+
+out:
+	inode_unlock_shared(inode);
+	return ret;
 }
 
 static int ext4_readpage(struct file *file, struct page *page)
@@ -3440,7 +3479,7 @@
 	 */
 	flags &= ~IOMAP_WRITE;
 	ret = ext4_iomap_begin(inode, offset, length, flags, iomap, srcmap);
-	WARN_ON_ONCE(iomap->type != IOMAP_MAPPED);
+	WARN_ON_ONCE(!ret && iomap->type != IOMAP_MAPPED);
 	return ret;
 }
 
@@ -3933,27 +3972,20 @@
  * Returns: 0 on success or negative on failure
  */
 
-int ext4_punch_hole(struct inode *inode, loff_t offset, loff_t length)
+int ext4_punch_hole(struct file *file, loff_t offset, loff_t length)
 {
+	struct inode *inode = file_inode(file);
 	struct super_block *sb = inode->i_sb;
 	ext4_lblk_t first_block, stop_block;
 	struct address_space *mapping = inode->i_mapping;
-	loff_t first_block_offset, last_block_offset;
+	loff_t first_block_offset, last_block_offset, max_length;
+	struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
 	handle_t *handle;
 	unsigned int credits;
 	int ret = 0, ret2 = 0;
 
 	trace_ext4_punch_hole(inode, offset, length, 0);
 
-	ext4_clear_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
-	if (ext4_has_inline_data(inode)) {
-		filemap_invalidate_lock(mapping);
-		ret = ext4_convert_inline_data(inode);
-		filemap_invalidate_unlock(mapping);
-		if (ret)
-			return ret;
-	}
-
 	/*
 	 * Write out all dirty pages to avoid race conditions
 	 * Then release them.
@@ -3981,6 +4013,14 @@
 		   offset;
 	}
 
+	/*
+	 * For punch hole the length + offset needs to be within one block
+	 * before last range. Adjust the length if it goes beyond that limit.
+	 */
+	max_length = sbi->s_bitmap_maxbytes - inode->i_sb->s_blocksize;
+	if (offset + length > max_length)
+		length = max_length - offset;
+
 	if (offset & (sb->s_blocksize - 1) ||
 	    (offset + length) & (sb->s_blocksize - 1)) {
 		/*
@@ -3996,6 +4036,10 @@
 	/* Wait all existing dio workers, newcomers will block on i_mutex */
 	inode_dio_wait(inode);
 
+	ret = file_modified(file);
+	if (ret)
+		goto out_mutex;
+
 	/*
 	 * Prevent page faults from reinstantiating pages we have released from
 	 * page cache.
@@ -4165,7 +4209,8 @@
 
 	/* If we zero-out tail of the page, we have to create jinode for jbd2 */
 	if (inode->i_size & (inode->i_sb->s_blocksize - 1)) {
-		if (ext4_inode_attach_jinode(inode) < 0)
+		err = ext4_inode_attach_jinode(inode);
+		if (err)
 			goto out_trace;
 	}
 
@@ -4266,9 +4311,17 @@
 	inodes_per_block = EXT4_SB(sb)->s_inodes_per_block;
 	inode_offset = ((ino - 1) %
 			EXT4_INODES_PER_GROUP(sb));
-	block = ext4_inode_table(sb, gdp) + (inode_offset / inodes_per_block);
 	iloc->offset = (inode_offset % inodes_per_block) * EXT4_INODE_SIZE(sb);
 
+	block = ext4_inode_table(sb, gdp);
+	if ((block <= le32_to_cpu(EXT4_SB(sb)->s_es->s_first_data_block)) ||
+	    (block >= ext4_blocks_count(EXT4_SB(sb)->s_es))) {
+		ext4_error(sb, "Invalid inode table block %llu in "
+			   "block_group %u", block, iloc->block_group);
+		return -EFSCORRUPTED;
+	}
+	block += (inode_offset / inodes_per_block);
+
 	bh = sb_getblk(sb, block);
 	if (unlikely(!bh))
 		return -ENOMEM;
@@ -4374,7 +4427,7 @@
 static int __ext4_get_inode_loc_noinmem(struct inode *inode,
 					struct ext4_iloc *iloc)
 {
-	ext4_fsblk_t err_blk;
+	ext4_fsblk_t err_blk = 0;
 	int ret;
 
 	ret = __ext4_get_inode_loc(inode->i_sb, inode->i_ino, iloc, 0,
@@ -4389,7 +4442,7 @@
 
 int ext4_get_inode_loc(struct inode *inode, struct ext4_iloc *iloc)
 {
-	ext4_fsblk_t err_blk;
+	ext4_fsblk_t err_blk = 0;
 	int ret;
 
 	/* We have all inode data except xattrs in memory here. */
@@ -4498,11 +4551,15 @@
 	__le32 *magic = (void *)raw_inode +
 			EXT4_GOOD_OLD_INODE_SIZE + ei->i_extra_isize;
 
-	if (EXT4_GOOD_OLD_INODE_SIZE + ei->i_extra_isize + sizeof(__le32) <=
-	    EXT4_INODE_SIZE(inode->i_sb) &&
+	if (EXT4_INODE_HAS_XATTR_SPACE(inode)  &&
 	    *magic == cpu_to_le32(EXT4_XATTR_MAGIC)) {
+		int err;
+
 		ext4_set_inode_state(inode, EXT4_STATE_XATTR);
-		return ext4_find_inline_data_nolock(inode);
+		err = ext4_find_inline_data_nolock(inode);
+		if (!err && ext4_has_inline_data(inode))
+			ext4_set_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
+		return err;
 	} else
 		EXT4_I(inode)->i_inline_off = 0;
 	return 0;
@@ -4536,6 +4593,24 @@
 		return inode_peek_iversion(inode);
 }
 
+static const char *check_igot_inode(struct inode *inode, ext4_iget_flags flags)
+
+{
+	if (flags & EXT4_IGET_EA_INODE) {
+		if (!(EXT4_I(inode)->i_flags & EXT4_EA_INODE_FL))
+			return "missing EA_INODE flag";
+		if (ext4_test_inode_state(inode, EXT4_STATE_XATTR) ||
+		    EXT4_I(inode)->i_file_acl)
+			return "ea_inode with extended attributes";
+	} else {
+		if ((EXT4_I(inode)->i_flags & EXT4_EA_INODE_FL))
+			return "unexpected EA_INODE flag";
+	}
+	if (is_bad_inode(inode) && !(flags & EXT4_IGET_BAD))
+		return "unexpected bad inode w/o EXT4_IGET_BAD";
+	return NULL;
+}
+
 struct inode *__ext4_iget(struct super_block *sb, unsigned long ino,
 			  ext4_iget_flags flags, const char *function,
 			  unsigned int line)
@@ -4545,6 +4620,7 @@
 	struct ext4_inode_info *ei;
 	struct ext4_super_block *es = EXT4_SB(sb)->s_es;
 	struct inode *inode;
+	const char *err_str;
 	journal_t *journal = EXT4_SB(sb)->s_journal;
 	long ret;
 	loff_t size;
@@ -4572,8 +4648,14 @@
 	inode = iget_locked(sb, ino);
 	if (!inode)
 		return ERR_PTR(-ENOMEM);
-	if (!(inode->i_state & I_NEW))
+	if (!(inode->i_state & I_NEW)) {
+		if ((err_str = check_igot_inode(inode, flags)) != NULL) {
+			ext4_error_inode(inode, function, line, 0, err_str);
+			iput(inode);
+			return ERR_PTR(-EFSCORRUPTED);
+		}
 		return inode;
+	}
 
 	ei = EXT4_I(inode);
 	iloc.bh = NULL;
@@ -4583,13 +4665,6 @@
 		goto bad_inode;
 	raw_inode = ext4_raw_inode(&iloc);
 
-	if ((ino == EXT4_ROOT_INO) && (raw_inode->i_links_count == 0)) {
-		ext4_error_inode(inode, function, line, 0,
-				 "iget: root inode unallocated");
-		ret = -EFSCORRUPTED;
-		goto bad_inode;
-	}
-
 	if ((flags & EXT4_IGET_HANDLE) &&
 	    (raw_inode->i_links_count == 0) && (raw_inode->i_mode == 0)) {
 		ret = -ESTALE;
@@ -4662,11 +4737,16 @@
 	 * NeilBrown 1999oct15
 	 */
 	if (inode->i_nlink == 0) {
-		if ((inode->i_mode == 0 ||
+		if ((inode->i_mode == 0 || flags & EXT4_IGET_SPECIAL ||
 		     !(EXT4_SB(inode->i_sb)->s_mount_state & EXT4_ORPHAN_FS)) &&
 		    ino != EXT4_BOOT_LOADER_INO) {
-			/* this inode is deleted */
-			ret = -ESTALE;
+			/* this inode is deleted or unallocated */
+			if (flags & EXT4_IGET_SPECIAL) {
+				ext4_error_inode(inode, function, line, 0,
+						 "iget: special inode unallocated");
+				ret = -EFSCORRUPTED;
+			} else
+				ret = -ESTALE;
 			goto bad_inode;
 		}
 		/* The only unlinked inodes we let through here have
@@ -4841,11 +4921,19 @@
 				 "iget: bogus i_mode (%o)", inode->i_mode);
 		goto bad_inode;
 	}
-	if (IS_CASEFOLDED(inode) && !ext4_has_feature_casefold(inode->i_sb))
+	if (IS_CASEFOLDED(inode) && !ext4_has_feature_casefold(inode->i_sb)) {
 		ext4_error_inode(inode, function, line, 0,
 				 "casefold flag without casefold feature");
-	brelse(iloc.bh);
+		ret = -EFSCORRUPTED;
+		goto bad_inode;
+	}
+	if ((err_str = check_igot_inode(inode, flags)) != NULL) {
+		ext4_error_inode(inode, function, line, 0, err_str);
+		ret = -EFSCORRUPTED;
+		goto bad_inode;
+	}
 
+	brelse(iloc.bh);
 	unlock_new_inode(inode);
 	return inode;
 
@@ -5166,7 +5254,7 @@
 
 	if (EXT4_SB(inode->i_sb)->s_journal) {
 		if (ext4_journal_current_handle()) {
-			jbd_debug(1, "called recursively, non-PF_MEMALLOC!\n");
+			ext4_debug("called recursively, non-PF_MEMALLOC!\n");
 			dump_stack();
 			return -EIO;
 		}
@@ -5213,8 +5301,9 @@
 	struct page *page;
 	unsigned offset;
 	journal_t *journal = EXT4_SB(inode->i_sb)->s_journal;
-	tid_t commit_tid = 0;
+	tid_t commit_tid;
 	int ret;
+	bool has_transaction;
 
 	offset = inode->i_size & (PAGE_SIZE - 1);
 	/*
@@ -5239,12 +5328,14 @@
 		put_page(page);
 		if (ret != -EBUSY)
 			return;
-		commit_tid = 0;
+		has_transaction = false;
 		read_lock(&journal->j_state_lock);
-		if (journal->j_committing_transaction)
+		if (journal->j_committing_transaction) {
 			commit_tid = journal->j_committing_transaction->t_tid;
+			has_transaction = true;
+		}
 		read_unlock(&journal->j_state_lock);
-		if (commit_tid)
+		if (has_transaction)
 			jbd2_log_wait_commit(journal, commit_tid);
 	}
 }
@@ -5309,7 +5400,7 @@
 		if (error)
 			return error;
 	}
-	ext4_fc_start_update(inode);
+
 	if ((ia_valid & ATTR_UID && !uid_eq(attr->ia_uid, inode->i_uid)) ||
 	    (ia_valid & ATTR_GID && !gid_eq(attr->ia_gid, inode->i_gid))) {
 		handle_t *handle;
@@ -5333,7 +5424,6 @@
 
 		if (error) {
 			ext4_journal_stop(handle);
-			ext4_fc_stop_update(inode);
 			return error;
 		}
 		/* Update corresponding info in inode so that everything is in
@@ -5345,7 +5435,6 @@
 		error = ext4_mark_inode_dirty(handle, inode);
 		ext4_journal_stop(handle);
 		if (unlikely(error)) {
-			ext4_fc_stop_update(inode);
 			return error;
 		}
 	}
@@ -5353,18 +5442,17 @@
 	if (attr->ia_valid & ATTR_SIZE) {
 		handle_t *handle;
 		loff_t oldsize = inode->i_size;
+		loff_t old_disksize;
 		int shrink = (attr->ia_size < inode->i_size);
 
 		if (!(ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS))) {
 			struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
 
 			if (attr->ia_size > sbi->s_bitmap_maxbytes) {
-				ext4_fc_stop_update(inode);
 				return -EFBIG;
 			}
 		}
 		if (!S_ISREG(inode->i_mode)) {
-			ext4_fc_stop_update(inode);
 			return -EINVAL;
 		}
 
@@ -5416,8 +5504,7 @@
 				ext4_fc_track_range(handle, inode,
 					(attr->ia_size > 0 ? attr->ia_size - 1 : 0) >>
 					inode->i_sb->s_blocksize_bits,
-					(oldsize > 0 ? oldsize - 1 : 0) >>
-					inode->i_sb->s_blocksize_bits);
+					EXT_MAX_BLOCKS - 1);
 			else
 				ext4_fc_track_range(
 					handle, inode,
@@ -5427,6 +5514,7 @@
 					inode->i_sb->s_blocksize_bits);
 
 			down_write(&EXT4_I(inode)->i_data_sem);
+			old_disksize = EXT4_I(inode)->i_disksize;
 			EXT4_I(inode)->i_disksize = attr->ia_size;
 			rc = ext4_mark_inode_dirty(handle, inode);
 			if (!error)
@@ -5438,6 +5526,8 @@
 			 */
 			if (!error)
 				i_size_write(inode, attr->ia_size);
+			else
+				EXT4_I(inode)->i_disksize = old_disksize;
 			up_write(&EXT4_I(inode)->i_data_sem);
 			ext4_journal_stop(handle);
 			if (error)
@@ -5488,7 +5578,6 @@
 		ext4_std_error(inode->i_sb, error);
 	if (!error)
 		error = rc;
-	ext4_fc_stop_update(inode);
 	return error;
 }
 
@@ -5673,7 +5762,12 @@
 	}
 	ext4_fc_track_inode(handle, inode);
 
-	if (IS_I_VERSION(inode))
+	/*
+	 * ea_inodes are using i_version for storing reference count, don't
+	 * mess with it
+	 */
+	if (IS_I_VERSION(inode) &&
+	    !(EXT4_I(inode)->i_flags & EXT4_EA_INODE_FL))
 		inode_inc_iversion(inode);
 
 	/* the do_update_inode consumes one bh->b_count */
@@ -5751,6 +5845,14 @@
 		return 0;
 	}
 
+	/*
+	 * We may need to allocate external xattr block so we need quotas
+	 * initialized. Here we can be called with various locks held so we
+	 * cannot affort to initialize quotas ourselves. So just bail.
+	 */
+	if (dquot_initialize_needed(inode))
+		return -EAGAIN;
+
 	/* try to expand with EAs present */
 	error = ext4_expand_extra_isize_ea(inode, new_extra_isize,
 					   raw_inode, handle);
@@ -5989,7 +6091,7 @@
 		return PTR_ERR(handle);
 
 	ext4_fc_mark_ineligible(inode->i_sb,
-		EXT4_FC_REASON_JOURNAL_FLAG_CHANGE);
+		EXT4_FC_REASON_JOURNAL_FLAG_CHANGE, handle);
 	err = ext4_mark_inode_dirty(handle, inode);
 	ext4_handle_sync(handle);
 	ext4_journal_stop(handle);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/ioctl.c
@@ -124,7 +124,8 @@
 	blkcnt_t blocks;
 	unsigned short bytes;
 
-	inode_bl = ext4_iget(sb, EXT4_BOOT_LOADER_INO, EXT4_IGET_SPECIAL);
+	inode_bl = ext4_iget(sb, EXT4_BOOT_LOADER_INO,
+			EXT4_IGET_SPECIAL | EXT4_IGET_BAD);
 	if (IS_ERR(inode_bl))
 		return PTR_ERR(inode_bl);
 	ei_bl = EXT4_I(inode_bl);
@@ -169,12 +170,12 @@
 		err = -EINVAL;
 		goto err_out;
 	}
-	ext4_fc_start_ineligible(sb, EXT4_FC_REASON_SWAP_BOOT);
+	ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_SWAP_BOOT, handle);
 
 	/* Protect extent tree against block allocations via delalloc */
 	ext4_double_down_write_data_sem(inode, inode_bl);
 
-	if (inode_bl->i_nlink == 0) {
+	if (is_bad_inode(inode_bl) || !S_ISREG(inode_bl->i_mode)) {
 		/* this inode has never been used as a BOOT_LOADER */
 		set_nlink(inode_bl, 1);
 		i_uid_write(inode_bl, 0);
@@ -183,6 +184,7 @@
 		ei_bl->i_flags = 0;
 		inode_set_iversion(inode_bl, 1);
 		i_size_write(inode_bl, 0);
+		EXT4_I(inode_bl)->i_disksize = inode_bl->i_size;
 		inode_bl->i_mode = S_IFREG;
 		if (ext4_has_feature_extents(sb)) {
 			ext4_set_inode_flag(inode_bl, EXT4_INODE_EXTENTS);
@@ -252,7 +254,6 @@
 
 err_out1:
 	ext4_journal_stop(handle);
-	ext4_fc_stop_ineligible(sb);
 	ext4_double_up_write_data_sem(inode, inode_bl);
 
 err_out:
@@ -492,6 +493,10 @@
 	if (ext4_is_quota_file(inode))
 		return err;
 
+	err = dquot_initialize(inode);
+	if (err)
+		return err;
+
 	err = ext4_get_inode_loc(inode, &iloc);
 	if (err)
 		return err;
@@ -507,10 +512,6 @@
 		brelse(iloc.bh);
 	}
 
-	err = dquot_initialize(inode);
-	if (err)
-		return err;
-
 	handle = ext4_journal_start(inode, EXT4_HT_QUOTA,
 		EXT4_QUOTA_INIT_BLOCKS(sb) +
 		EXT4_QUOTA_DEL_BLOCKS(sb) + 3);
@@ -558,6 +559,7 @@
 {
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	__u32 flags;
+	int ret;
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
@@ -576,7 +578,9 @@
 
 	switch (flags) {
 	case EXT4_GOING_FLAGS_DEFAULT:
-		freeze_bdev(sb->s_bdev);
+		ret = freeze_bdev(sb->s_bdev);
+		if (ret)
+			return ret;
 		set_bit(EXT4_FLAGS_SHUTDOWN, &sbi->s_ext4_flags);
 		thaw_bdev(sb->s_bdev);
 		break;
@@ -743,7 +747,6 @@
 	u32 flags = fa->flags;
 	int err = -EOPNOTSUPP;
 
-	ext4_fc_start_update(inode);
 	if (flags & ~EXT4_FL_USER_VISIBLE)
 		goto out;
 
@@ -764,7 +767,6 @@
 		goto out;
 	err = ext4_ioctl_setproject(inode, fa->fsx_projid);
 out:
-	ext4_fc_stop_update(inode);
 	return err;
 }
 
@@ -1076,7 +1078,7 @@
 
 		err = ext4_resize_fs(sb, n_blocks_count);
 		if (EXT4_SB(sb)->s_journal) {
-			ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_RESIZE);
+			ext4_fc_mark_ineligible(sb, EXT4_FC_REASON_RESIZE, NULL);
 			jbd2_journal_lock_updates(EXT4_SB(sb)->s_journal);
 			err2 = jbd2_journal_flush(EXT4_SB(sb)->s_journal, 0);
 			jbd2_journal_unlock_updates(EXT4_SB(sb)->s_journal);
@@ -1117,8 +1119,6 @@
 		    sizeof(range)))
 			return -EFAULT;
 
-		range.minlen = max((unsigned int)range.minlen,
-				   q->limits.discard_granularity);
 		ret = ext4_trim_fs(sb, &range);
 		if (ret < 0)
 			return ret;
@@ -1273,13 +1273,7 @@
 
 long ext4_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
 {
-	long ret;
-
-	ext4_fc_start_update(file_inode(filp));
-	ret = __ext4_ioctl(filp, cmd, arg);
-	ext4_fc_stop_update(file_inode(filp));
-
-	return ret;
+	return __ext4_ioctl(filp, cmd, arg);
 }
 
 #ifdef CONFIG_COMPAT
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/mballoc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/mballoc.c
@@ -16,6 +16,7 @@
 #include <linux/slab.h>
 #include <linux/nospec.h>
 #include <linux/backing-dev.h>
+#include <linux/freezer.h>
 #include <trace/events/ext4.h>
 
 /*
@@ -745,6 +746,8 @@
 	MB_CHECK_ASSERT(e4b->bd_info->bb_fragments == fragments);
 
 	grp = ext4_get_group_info(sb, e4b->bd_group);
+	if (!grp)
+		return NULL;
 	list_for_each(cur, &grp->bb_prealloc_list) {
 		ext4_group_t groupnr;
 		struct ext4_prealloc_space *pa;
@@ -850,7 +853,7 @@
 {
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 
-	if (!test_opt2(sb, MB_OPTIMIZE_SCAN) || grp->bb_free == 0)
+	if (!test_opt2(sb, MB_OPTIMIZE_SCAN) || grp->bb_fragments == 0)
 		return;
 
 	write_lock(&sbi->s_mb_rb_lock);
@@ -1000,7 +1003,7 @@
 		return 0;
 	if (ac->ac_criteria >= 2)
 		return 0;
-	if (ext4_test_inode_flag(ac->ac_inode, EXT4_INODE_EXTENTS))
+	if (!ext4_test_inode_flag(ac->ac_inode, EXT4_INODE_EXTENTS))
 		return 0;
 	return 1;
 }
@@ -1009,8 +1012,9 @@
  * Return next linear group for allocation. If linear traversal should not be
  * performed, this function just returns the same group
  */
-static int
-next_linear_group(struct ext4_allocation_context *ac, int group, int ngroups)
+static ext4_group_t
+next_linear_group(struct ext4_allocation_context *ac, ext4_group_t group,
+		  ext4_group_t ngroups)
 {
 	if (!should_optimize_scan(ac))
 		goto inc_and_return;
@@ -1052,8 +1056,10 @@
 {
 	*new_cr = ac->ac_criteria;
 
-	if (!should_optimize_scan(ac) || ac->ac_groups_linear_remaining)
+	if (!should_optimize_scan(ac) || ac->ac_groups_linear_remaining) {
+		*group = next_linear_group(ac, *group, ngroups);
 		return;
+	}
 
 	if (*new_cr == 0) {
 		ext4_mb_choose_next_group_cr0(ac, new_cr, group, ngroups);
@@ -1078,23 +1084,25 @@
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	int i;
 
-	if (test_opt2(sb, MB_OPTIMIZE_SCAN) && grp->bb_largest_free_order >= 0) {
+	for (i = MB_NUM_ORDERS(sb) - 1; i >= 0; i--)
+		if (grp->bb_counters[i] > 0)
+			break;
+	/* No need to move between order lists? */
+	if (!test_opt2(sb, MB_OPTIMIZE_SCAN) ||
+	    i == grp->bb_largest_free_order) {
+		grp->bb_largest_free_order = i;
+		return;
+	}
+
+	if (grp->bb_largest_free_order >= 0) {
 		write_lock(&sbi->s_mb_largest_free_orders_locks[
 					      grp->bb_largest_free_order]);
 		list_del_init(&grp->bb_largest_free_order_node);
 		write_unlock(&sbi->s_mb_largest_free_orders_locks[
 					      grp->bb_largest_free_order]);
 	}
-	grp->bb_largest_free_order = -1; /* uninit */
-
-	for (i = MB_NUM_ORDERS(sb) - 1; i >= 0; i--) {
-		if (grp->bb_counters[i] > 0) {
-			grp->bb_largest_free_order = i;
-			break;
-		}
-	}
-	if (test_opt2(sb, MB_OPTIMIZE_SCAN) &&
-	    grp->bb_largest_free_order >= 0 && grp->bb_free) {
+	grp->bb_largest_free_order = i;
+	if (grp->bb_largest_free_order >= 0 && grp->bb_free) {
 		write_lock(&sbi->s_mb_largest_free_orders_locks[
 					      grp->bb_largest_free_order]);
 		list_add_tail(&grp->bb_largest_free_order_node,
@@ -1106,9 +1114,9 @@
 
 static noinline_for_stack
 void ext4_mb_generate_buddy(struct super_block *sb,
-				void *buddy, void *bitmap, ext4_group_t group)
+			    void *buddy, void *bitmap, ext4_group_t group,
+			    struct ext4_group_info *grp)
 {
-	struct ext4_group_info *grp = ext4_get_group_info(sb, group);
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	ext4_grpblk_t max = EXT4_CLUSTERS_PER_GROUP(sb);
 	ext4_grpblk_t i = 0;
@@ -1160,6 +1168,24 @@
 	mb_update_avg_fragment_size(sb, grp);
 }
 
+static void mb_regenerate_buddy(struct ext4_buddy *e4b)
+{
+	int count;
+	int order = 1;
+	void *buddy;
+
+	while ((buddy = mb_find_buddy(e4b, order++, &count)))
+		ext4_set_bits(buddy, 0, count);
+
+	e4b->bd_info->bb_fragments = 0;
+	memset(e4b->bd_info->bb_counters, 0,
+		sizeof(*e4b->bd_info->bb_counters) *
+		(e4b->bd_sb->s_blocksize_bits + 2));
+
+	ext4_mb_generate_buddy(e4b->bd_sb, e4b->bd_buddy,
+		e4b->bd_bitmap, e4b->bd_group, e4b->bd_info);
+}
+
 /* The buddy information is attached the buddy cache inode
  * for convenience. The information regarding each group
  * is loaded via ext4_mb_load_buddy. The information involve
@@ -1229,6 +1255,8 @@
 			break;
 
 		grinfo = ext4_get_group_info(sb, group);
+		if (!grinfo)
+			continue;
 		/*
 		 * If page is uptodate then we came here after online resize
 		 * which added some new uninitialized group info structs, so
@@ -1294,6 +1322,10 @@
 				group, page->index, i * blocksize);
 			trace_ext4_mb_buddy_bitmap_load(sb, group);
 			grinfo = ext4_get_group_info(sb, group);
+			if (!grinfo) {
+				err = -EFSCORRUPTED;
+				goto out;
+			}
 			grinfo->bb_fragments = 0;
 			memset(grinfo->bb_counters, 0,
 			       sizeof(*grinfo->bb_counters) *
@@ -1304,7 +1336,7 @@
 			ext4_lock_group(sb, group);
 			/* init the buddy */
 			memset(data, 0xff, blocksize);
-			ext4_mb_generate_buddy(sb, data, incore, group);
+			ext4_mb_generate_buddy(sb, data, incore, group, grinfo);
 			ext4_unlock_group(sb, group);
 			incore = NULL;
 		} else {
@@ -1418,6 +1450,9 @@
 	might_sleep();
 	mb_debug(sb, "init group %u\n", group);
 	this_grp = ext4_get_group_info(sb, group);
+	if (!this_grp)
+		return -EFSCORRUPTED;
+
 	/*
 	 * This ensures that we don't reinit the buddy cache
 	 * page which map to the group from which we are already
@@ -1492,6 +1527,8 @@
 
 	blocks_per_page = PAGE_SIZE / sb->s_blocksize;
 	grp = ext4_get_group_info(sb, group);
+	if (!grp)
+		return -EFSCORRUPTED;
 
 	e4b->bd_blkbits = sb->s_blocksize_bits;
 	e4b->bd_info = grp;
@@ -1798,11 +1835,6 @@
 	mb_check_buddy(e4b);
 	mb_free_blocks_double(inode, e4b, first, count);
 
-	this_cpu_inc(discard_pa_seq);
-	e4b->bd_info->bb_free += count;
-	if (first < e4b->bd_info->bb_first_free)
-		e4b->bd_info->bb_first_free = first;
-
 	/* access memory sequentially: check left neighbour,
 	 * clear range and then check right neighbour
 	 */
@@ -1816,21 +1848,31 @@
 		struct ext4_sb_info *sbi = EXT4_SB(sb);
 		ext4_fsblk_t blocknr;
 
+		/*
+		 * Fastcommit replay can free already freed blocks which
+		 * corrupts allocation info. Regenerate it.
+		 */
+		if (sbi->s_mount_state & EXT4_FC_REPLAY) {
+			mb_regenerate_buddy(e4b);
+			goto check;
+		}
+
 		blocknr = ext4_group_first_block_no(sb, e4b->bd_group);
 		blocknr += EXT4_C2B(sbi, block);
-		if (!(sbi->s_mount_state & EXT4_FC_REPLAY)) {
-			ext4_grp_locked_error(sb, e4b->bd_group,
-					      inode ? inode->i_ino : 0,
-					      blocknr,
-					      "freeing already freed block (bit %u); block bitmap corrupt.",
-					      block);
-			ext4_mark_group_bitmap_corrupted(
-				sb, e4b->bd_group,
+		ext4_grp_locked_error(sb, e4b->bd_group,
+				      inode ? inode->i_ino : 0, blocknr,
+				      "freeing already freed block (bit %u); block bitmap corrupt.",
+				      block);
+		ext4_mark_group_bitmap_corrupted(sb, e4b->bd_group,
 				EXT4_GROUP_INFO_BBITMAP_CORRUPT);
-		}
-		goto done;
+		return;
 	}
 
+	this_cpu_inc(discard_pa_seq);
+	e4b->bd_info->bb_free += count;
+	if (first < e4b->bd_info->bb_first_free)
+		e4b->bd_info->bb_first_free = first;
+
 	/* let's maintain fragments counter */
 	if (left_is_free && right_is_free)
 		e4b->bd_info->bb_fragments--;
@@ -1855,9 +1897,9 @@
 	if (first <= last)
 		mb_buddy_mark_free(e4b, first >> 1, last >> 1);
 
-done:
 	mb_set_largest_free_order(sb, e4b->bd_info);
 	mb_update_avg_fragment_size(sb, e4b->bd_info);
+check:
 	mb_check_buddy(e4b);
 }
 
@@ -2178,6 +2220,9 @@
 		return err;
 
 	ext4_lock_group(ac->ac_sb, group);
+	if (unlikely(EXT4_MB_GRP_BBITMAP_CORRUPT(e4b->bd_info)))
+		goto out;
+
 	max = mb_find_extent(e4b, ex.fe_start, ex.fe_len, &ex);
 
 	if (max > 0) {
@@ -2185,6 +2230,7 @@
 		ext4_mb_use_best_found(ac, e4b);
 	}
 
+out:
 	ext4_unlock_group(ac->ac_sb, group);
 	ext4_mb_unload_buddy(e4b);
 
@@ -2202,7 +2248,9 @@
 	struct ext4_group_info *grp = ext4_get_group_info(ac->ac_sb, group);
 	struct ext4_free_extent ex;
 
-	if (!(ac->ac_flags & EXT4_MB_HINT_TRY_GOAL))
+	if (!grp)
+		return -EFSCORRUPTED;
+	if (!(ac->ac_flags & (EXT4_MB_HINT_TRY_GOAL | EXT4_MB_HINT_GOAL_ONLY)))
 		return 0;
 	if (grp->bb_free == 0)
 		return 0;
@@ -2211,12 +2259,10 @@
 	if (err)
 		return err;
 
-	if (unlikely(EXT4_MB_GRP_BBITMAP_CORRUPT(e4b->bd_info))) {
-		ext4_mb_unload_buddy(e4b);
-		return 0;
-	}
-
 	ext4_lock_group(ac->ac_sb, group);
+	if (unlikely(EXT4_MB_GRP_BBITMAP_CORRUPT(e4b->bd_info)))
+		goto out;
+
 	max = mb_find_extent(e4b, ac->ac_g_ex.fe_start,
 			     ac->ac_g_ex.fe_len, &ex);
 	ex.fe_logical = 0xDEADFA11; /* debug value */
@@ -2224,8 +2270,7 @@
 	if (max >= ac->ac_g_ex.fe_len && ac->ac_g_ex.fe_len == sbi->s_stripe) {
 		ext4_fsblk_t start;
 
-		start = ext4_group_first_block_no(ac->ac_sb, e4b->bd_group) +
-			ex.fe_start;
+		start = ext4_grp_offs_to_block(ac->ac_sb, &ex);
 		/* use do_div to get remainder (would be 64-bit modulo) */
 		if (do_div(start, sbi->s_stripe) == 0) {
 			ac->ac_found++;
@@ -2249,6 +2294,7 @@
 		ac->ac_b_ex = ex;
 		ext4_mb_use_best_found(ac, e4b);
 	}
+out:
 	ext4_unlock_group(ac->ac_sb, group);
 	ext4_mb_unload_buddy(e4b);
 
@@ -2426,7 +2472,7 @@
 
 	BUG_ON(cr < 0 || cr >= 4);
 
-	if (unlikely(EXT4_MB_GRP_BBITMAP_CORRUPT(grp)))
+	if (unlikely(!grp || EXT4_MB_GRP_BBITMAP_CORRUPT(grp)))
 		return false;
 
 	free = grp->bb_free;
@@ -2495,6 +2541,8 @@
 	ext4_grpblk_t free;
 	int ret = 0;
 
+	if (!grp)
+		return -EFSCORRUPTED;
 	if (sbi->s_mb_stats)
 		atomic64_inc(&sbi->s_bal_cX_groups_considered[ac->ac_criteria]);
 	if (should_lock) {
@@ -2575,7 +2623,7 @@
 		 * prefetch once, so we avoid getblk() call, which can
 		 * be expensive.
 		 */
-		if (!EXT4_MB_GRP_TEST_AND_SET_READ(grp) &&
+		if (gdp && grp && !EXT4_MB_GRP_TEST_AND_SET_READ(grp) &&
 		    EXT4_MB_GRP_NEED_INIT(grp) &&
 		    ext4_free_group_clusters(sb, gdp) > 0 &&
 		    !(ext4_has_group_desc_csum(sb) &&
@@ -2619,7 +2667,7 @@
 		group--;
 		grp = ext4_get_group_info(sb, group);
 
-		if (EXT4_MB_GRP_NEED_INIT(grp) &&
+		if (grp && gdp && EXT4_MB_GRP_NEED_INIT(grp) &&
 		    ext4_free_group_clusters(sb, gdp) > 0 &&
 		    !(ext4_has_group_desc_csum(sb) &&
 		      (gdp->bg_flags & cpu_to_le16(EXT4_BG_BLOCK_UNINIT)))) {
@@ -2633,7 +2681,7 @@
 ext4_mb_regular_allocator(struct ext4_allocation_context *ac)
 {
 	ext4_group_t prefetch_grp = 0, ngroups, group, i;
-	int cr = -1;
+	int cr = -1, new_cr;
 	int err = 0, first_err = 0;
 	unsigned int nr = 0, prefetch_ios = 0;
 	struct ext4_sb_info *sbi;
@@ -2708,13 +2756,11 @@
 		ac->ac_groups_linear_remaining = sbi->s_mb_max_linear_groups;
 		prefetch_grp = group;
 
-		for (i = 0; i < ngroups; group = next_linear_group(ac, group, ngroups),
-			     i++) {
-			int ret = 0, new_cr;
+		for (i = 0, new_cr = cr; i < ngroups; i++,
+		     ext4_mb_choose_next_group(ac, &new_cr, &group, ngroups)) {
+			int ret = 0;
 
 			cond_resched();
-
-			ext4_mb_choose_next_group(ac, &new_cr, &group, ngroups);
 			if (new_cr != cr) {
 				cr = new_cr;
 				goto repeat;
@@ -2881,6 +2927,8 @@
 		sizeof(struct ext4_group_info);
 
 	grinfo = ext4_get_group_info(sb, group);
+	if (!grinfo)
+		return 0;
 	/* Load the group info in memory only if not already loaded. */
 	if (unlikely(EXT4_MB_GRP_NEED_INIT(grinfo))) {
 		err = ext4_mb_load_buddy(sb, group, &e4b);
@@ -2891,7 +2939,7 @@
 		buddy_loaded = 1;
 	}
 
-	memcpy(&sg, ext4_get_group_info(sb, group), i);
+	memcpy(&sg, grinfo, i);
 
 	if (buddy_loaded)
 		ext4_mb_unload_buddy(&e4b);
@@ -2901,7 +2949,10 @@
 	for (i = 0; i <= 13; i++)
 		seq_printf(seq, " %-5u", i <= blocksize_bits + 1 ?
 				sg.info.bb_counters[i] : 0);
-	seq_puts(seq, " ]\n");
+	seq_puts(seq, " ]");
+	if (EXT4_MB_GRP_BBITMAP_CORRUPT(&sg.info))
+		seq_puts(seq, " Block bitmap corrupted!");
+	seq_puts(seq, "\n");
 
 	return 0;
 }
@@ -3263,8 +3314,12 @@
 
 err_freebuddy:
 	cachep = get_groupinfo_cache(sb->s_blocksize_bits);
-	while (i-- > 0)
-		kmem_cache_free(cachep, ext4_get_group_info(sb, i));
+	while (i-- > 0) {
+		struct ext4_group_info *grp = ext4_get_group_info(sb, i);
+
+		if (grp)
+			kmem_cache_free(cachep, grp);
+	}
 	i = sbi->s_group_info_size;
 	rcu_read_lock();
 	group_info = rcu_dereference(sbi->s_group_info);
@@ -3560,6 +3615,8 @@
 		for (i = 0; i < ngroups; i++) {
 			cond_resched();
 			grinfo = ext4_get_group_info(sb, i);
+			if (!grinfo)
+				continue;
 			mb_group_bb_bitmap_free(grinfo);
 			ext4_lock_group(sb, i);
 			count = ext4_mb_cleanup_pa(grinfo);
@@ -3664,11 +3721,8 @@
 	/*
 	 * Clear the trimmed flag for the group so that the next
 	 * ext4_trim_fs can trim it.
-	 * If the volume is mounted with -o discard, online discard
-	 * is supported and the free blocks will be trimmed online.
 	 */
-	if (!test_opt(sb, DISCARD))
-		EXT4_MB_GRP_CLEAR_TRIMMED(db);
+	EXT4_MB_GRP_CLEAR_TRIMMED(db);
 
 	if (!db->bb_free_root.rb_node) {
 		/* No more items in the per group rb tree
@@ -3899,69 +3953,95 @@
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	ext4_group_t group;
 	ext4_grpblk_t blkoff;
-	int i, clen, err;
+	int i, err;
 	int already;
+	unsigned int clen, clen_changed, thisgrp_len;
 
-	clen = EXT4_B2C(sbi, len);
+	while (len > 0) {
+		ext4_get_group_no_and_offset(sb, block, &group, &blkoff);
 
-	ext4_get_group_no_and_offset(sb, block, &group, &blkoff);
-	bitmap_bh = ext4_read_block_bitmap(sb, group);
-	if (IS_ERR(bitmap_bh)) {
-		err = PTR_ERR(bitmap_bh);
-		bitmap_bh = NULL;
-		goto out_err;
-	}
+		/*
+		 * Check to see if we are freeing blocks across a group
+		 * boundary.
+		 * In case of flex_bg, this can happen that (block, len) may
+		 * span across more than one group. In that case we need to
+		 * get the corresponding group metadata to work with.
+		 * For this we have goto again loop.
+		 */
+		thisgrp_len = min_t(unsigned int, (unsigned int)len,
+			EXT4_BLOCKS_PER_GROUP(sb) - EXT4_C2B(sbi, blkoff));
+		clen = EXT4_NUM_B2C(sbi, thisgrp_len);
 
-	err = -EIO;
-	gdp = ext4_get_group_desc(sb, group, &gdp_bh);
-	if (!gdp)
-		goto out_err;
+		bitmap_bh = ext4_read_block_bitmap(sb, group);
+		if (IS_ERR(bitmap_bh)) {
+			err = PTR_ERR(bitmap_bh);
+			bitmap_bh = NULL;
+			break;
+		}
 
-	ext4_lock_group(sb, group);
-	already = 0;
-	for (i = 0; i < clen; i++)
-		if (!mb_test_bit(blkoff + i, bitmap_bh->b_data) == !state)
-			already++;
+		err = -EIO;
+		gdp = ext4_get_group_desc(sb, group, &gdp_bh);
+		if (!gdp)
+			break;
 
-	if (state)
-		ext4_set_bits(bitmap_bh->b_data, blkoff, clen);
-	else
-		mb_test_and_clear_bits(bitmap_bh->b_data, blkoff, clen);
-	if (ext4_has_group_desc_csum(sb) &&
-	    (gdp->bg_flags & cpu_to_le16(EXT4_BG_BLOCK_UNINIT))) {
-		gdp->bg_flags &= cpu_to_le16(~EXT4_BG_BLOCK_UNINIT);
-		ext4_free_group_clusters_set(sb, gdp,
-					     ext4_free_clusters_after_init(sb,
-						group, gdp));
-	}
-	if (state)
-		clen = ext4_free_group_clusters(sb, gdp) - clen + already;
-	else
-		clen = ext4_free_group_clusters(sb, gdp) + clen - already;
+		ext4_lock_group(sb, group);
+		already = 0;
+		for (i = 0; i < clen; i++)
+			if (!mb_test_bit(blkoff + i, bitmap_bh->b_data) ==
+					 !state)
+				already++;
+
+		clen_changed = clen - already;
+		if (state)
+			ext4_set_bits(bitmap_bh->b_data, blkoff, clen);
+		else
+			mb_test_and_clear_bits(bitmap_bh->b_data, blkoff, clen);
+		if (ext4_has_group_desc_csum(sb) &&
+		    (gdp->bg_flags & cpu_to_le16(EXT4_BG_BLOCK_UNINIT))) {
+			gdp->bg_flags &= cpu_to_le16(~EXT4_BG_BLOCK_UNINIT);
+			ext4_free_group_clusters_set(sb, gdp,
+			     ext4_free_clusters_after_init(sb, group, gdp));
+		}
+		if (state)
+			clen = ext4_free_group_clusters(sb, gdp) - clen_changed;
+		else
+			clen = ext4_free_group_clusters(sb, gdp) + clen_changed;
 
-	ext4_free_group_clusters_set(sb, gdp, clen);
-	ext4_block_bitmap_csum_set(sb, group, gdp, bitmap_bh);
-	ext4_group_desc_csum_set(sb, group, gdp);
+		ext4_free_group_clusters_set(sb, gdp, clen);
+		ext4_block_bitmap_csum_set(sb, group, gdp, bitmap_bh);
+		ext4_group_desc_csum_set(sb, group, gdp);
 
-	ext4_unlock_group(sb, group);
+		ext4_unlock_group(sb, group);
 
-	if (sbi->s_log_groups_per_flex) {
-		ext4_group_t flex_group = ext4_flex_group(sbi, group);
+		if (sbi->s_log_groups_per_flex) {
+			ext4_group_t flex_group = ext4_flex_group(sbi, group);
+			struct flex_groups *fg = sbi_array_rcu_deref(sbi,
+						   s_flex_groups, flex_group);
 
-		atomic64_sub(len,
-			     &sbi_array_rcu_deref(sbi, s_flex_groups,
-						  flex_group)->free_clusters);
+			if (state)
+				atomic64_sub(clen_changed, &fg->free_clusters);
+			else
+				atomic64_add(clen_changed, &fg->free_clusters);
+
+		}
+
+		err = ext4_handle_dirty_metadata(NULL, NULL, bitmap_bh);
+		if (err)
+			break;
+		sync_dirty_buffer(bitmap_bh);
+		err = ext4_handle_dirty_metadata(NULL, NULL, gdp_bh);
+		sync_dirty_buffer(gdp_bh);
+		if (err)
+			break;
+
+		block += thisgrp_len;
+		len -= thisgrp_len;
+		brelse(bitmap_bh);
+		BUG_ON(len < 0);
 	}
 
-	err = ext4_handle_dirty_metadata(NULL, NULL, bitmap_bh);
 	if (err)
-		goto out_err;
-	sync_dirty_buffer(bitmap_bh);
-	err = ext4_handle_dirty_metadata(NULL, NULL, gdp_bh);
-	sync_dirty_buffer(gdp_bh);
-
-out_err:
-	brelse(bitmap_bh);
+		brelse(bitmap_bh);
 }
 
 /*
@@ -3992,9 +4072,9 @@
 				struct ext4_allocation_request *ar)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(ac->ac_sb);
+	struct ext4_super_block *es = sbi->s_es;
 	int bsbits, max;
-	ext4_lblk_t end;
-	loff_t size, start_off;
+	loff_t size, start_off, end;
 	loff_t orig_size __maybe_unused;
 	ext4_lblk_t start;
 	struct ext4_inode_info *ei = EXT4_I(ac->ac_inode);
@@ -4023,7 +4103,7 @@
 
 	/* first, let's learn actual file size
 	 * given current request is allocated */
-	size = ac->ac_o_ex.fe_logical + EXT4_C2B(sbi, ac->ac_o_ex.fe_len);
+	size = extent_logical_end(sbi, &ac->ac_o_ex);
 	size = size << bsbits;
 	if (size < i_size_read(ac->ac_inode))
 		size = i_size_read(ac->ac_inode);
@@ -4073,6 +4153,19 @@
 	size = size >> bsbits;
 	start = start_off >> bsbits;
 
+	/*
+	 * For tiny groups (smaller than 8MB) the chosen allocation
+	 * alignment may be larger than group size. Make sure the
+	 * alignment does not move allocation to a different group which
+	 * makes mballoc fail assertions later.
+	 */
+	start = max(start, rounddown(ac->ac_o_ex.fe_logical,
+			(ext4_lblk_t)EXT4_BLOCKS_PER_GROUP(ac->ac_sb)));
+
+	/* avoid unnecessary preallocation that may trigger assertions */
+	if (start + size > EXT_MAX_BLOCKS)
+		size = EXT_MAX_BLOCKS - start;
+
 	/* don't cover already allocated blocks in selected range */
 	if (ar->pleft && start <= ar->lleft) {
 		size -= ar->lleft + 1 - start;
@@ -4093,7 +4186,7 @@
 	/* check we don't cross already preallocated blocks */
 	rcu_read_lock();
 	list_for_each_entry_rcu(pa, &ei->i_prealloc_list, pa_inode_list) {
-		ext4_lblk_t pa_end;
+		loff_t pa_end;
 
 		if (pa->pa_deleted)
 			continue;
@@ -4103,8 +4196,7 @@
 			continue;
 		}
 
-		pa_end = pa->pa_lstart + EXT4_C2B(EXT4_SB(ac->ac_sb),
-						  pa->pa_len);
+		pa_end = pa_logical_end(EXT4_SB(ac->ac_sb), pa);
 
 		/* PA must not overlap original request */
 		BUG_ON(!(ac->ac_o_ex.fe_logical >= pa_end ||
@@ -4133,12 +4225,11 @@
 	/* XXX: extra loop to check we really don't overlap preallocations */
 	rcu_read_lock();
 	list_for_each_entry_rcu(pa, &ei->i_prealloc_list, pa_inode_list) {
-		ext4_lblk_t pa_end;
+		loff_t pa_end;
 
 		spin_lock(&pa->pa_lock);
 		if (pa->pa_deleted == 0) {
-			pa_end = pa->pa_lstart + EXT4_C2B(EXT4_SB(ac->ac_sb),
-							  pa->pa_len);
+			pa_end = pa_logical_end(EXT4_SB(ac->ac_sb), pa);
 			BUG_ON(!(start >= pa_end || end <= pa->pa_lstart));
 		}
 		spin_unlock(&pa->pa_lock);
@@ -4163,18 +4254,21 @@
 	ac->ac_g_ex.fe_len = EXT4_NUM_B2C(sbi, size);
 
 	/* define goal start in order to merge */
-	if (ar->pright && (ar->lright == (start + size))) {
+	if (ar->pright && (ar->lright == (start + size)) &&
+	    ar->pright >= size &&
+	    ar->pright - size >= le32_to_cpu(es->s_first_data_block)) {
 		/* merge to the right */
 		ext4_get_group_no_and_offset(ac->ac_sb, ar->pright - size,
-						&ac->ac_f_ex.fe_group,
-						&ac->ac_f_ex.fe_start);
+						&ac->ac_g_ex.fe_group,
+						&ac->ac_g_ex.fe_start);
 		ac->ac_flags |= EXT4_MB_HINT_TRY_GOAL;
 	}
-	if (ar->pleft && (ar->lleft + 1 == start)) {
+	if (ar->pleft && (ar->lleft + 1 == start) &&
+	    ar->pleft + 1 < ext4_blocks_count(es)) {
 		/* merge to the left */
 		ext4_get_group_no_and_offset(ac->ac_sb, ar->pleft + 1,
-						&ac->ac_f_ex.fe_group,
-						&ac->ac_f_ex.fe_start);
+						&ac->ac_g_ex.fe_group,
+						&ac->ac_g_ex.fe_start);
 		ac->ac_flags |= EXT4_MB_HINT_TRY_GOAL;
 	}
 
@@ -4267,6 +4361,7 @@
 	BUG_ON(start < pa->pa_pstart);
 	BUG_ON(end > pa->pa_pstart + EXT4_C2B(sbi, pa->pa_len));
 	BUG_ON(pa->pa_free < len);
+	BUG_ON(ac->ac_b_ex.fe_len <= 0);
 	pa->pa_free -= len;
 
 	mb_debug(ac->ac_sb, "use %llu/%d from inode pa %p\n", start, len, pa);
@@ -4350,8 +4445,7 @@
 		/* all fields in this condition don't change,
 		 * so we can skip locking for them */
 		if (ac->ac_o_ex.fe_logical < pa->pa_lstart ||
-		    ac->ac_o_ex.fe_logical >= (pa->pa_lstart +
-					       EXT4_C2B(sbi, pa->pa_len)))
+		    ac->ac_o_ex.fe_logical >= pa_logical_end(sbi, pa))
 			continue;
 
 		/* non-extent files can't have physical blocks past 2^32 */
@@ -4429,6 +4523,8 @@
 	struct ext4_free_data *entry;
 
 	grp = ext4_get_group_info(sb, group);
+	if (!grp)
+		return;
 	n = rb_first(&(grp->bb_free_root));
 
 	while (n) {
@@ -4456,6 +4552,9 @@
 	int preallocated = 0;
 	int len;
 
+	if (!grp)
+		return;
+
 	/* all form of preallocation discards first load group,
 	 * so the only competing code is preallocation use.
 	 * we don't need any locking here
@@ -4591,37 +4690,51 @@
 	pa = ac->ac_pa;
 
 	if (ac->ac_b_ex.fe_len < ac->ac_g_ex.fe_len) {
-		int winl;
-		int wins;
-		int win;
-		int offs;
-
-		/* we can't allocate as much as normalizer wants.
-		 * so, found space must get proper lstart
-		 * to cover original request */
+		struct ext4_free_extent ex = {
+			.fe_logical = ac->ac_g_ex.fe_logical,
+			.fe_len = ac->ac_g_ex.fe_len,
+		};
+		loff_t orig_goal_end = extent_logical_end(sbi, &ex);
+		loff_t o_ex_end = extent_logical_end(sbi, &ac->ac_o_ex);
+
+		/*
+		 * We can't allocate as much as normalizer wants, so we try
+		 * to get proper lstart to cover the original request, except
+		 * when the goal doesn't cover the original request as below:
+		 *
+		 * orig_ex:2045/2055(10), isize:8417280 -> normalized:0/2048
+		 * best_ex:0/200(200) -> adjusted: 1848/2048(200)
+		 */
 		BUG_ON(ac->ac_g_ex.fe_logical > ac->ac_o_ex.fe_logical);
 		BUG_ON(ac->ac_g_ex.fe_len < ac->ac_o_ex.fe_len);
 
-		/* we're limited by original request in that
-		 * logical block must be covered any way
-		 * winl is window we can move our chunk within */
-		winl = ac->ac_o_ex.fe_logical - ac->ac_g_ex.fe_logical;
-
-		/* also, we should cover whole original request */
-		wins = EXT4_C2B(sbi, ac->ac_b_ex.fe_len - ac->ac_o_ex.fe_len);
-
-		/* the smallest one defines real window */
-		win = min(winl, wins);
-
-		offs = ac->ac_o_ex.fe_logical %
-			EXT4_C2B(sbi, ac->ac_b_ex.fe_len);
-		if (offs && offs < win)
-			win = offs;
+		/*
+		 * Use the below logic for adjusting best extent as it keeps
+		 * fragmentation in check while ensuring logical range of best
+		 * extent doesn't overflow out of goal extent:
+		 *
+		 * 1. Check if best ex can be kept at end of goal and still
+		 *    cover original start
+		 * 2. Else, check if best ex can be kept at start of goal and
+		 *    still cover original end
+		 * 3. Else, keep the best ex at start of original request.
+		 */
+		ex.fe_len = ac->ac_b_ex.fe_len;
+
+		ex.fe_logical = orig_goal_end - EXT4_C2B(sbi, ex.fe_len);
+		if (ac->ac_o_ex.fe_logical >= ex.fe_logical)
+			goto adjust_bex;
+
+		ex.fe_logical = ac->ac_g_ex.fe_logical;
+		if (o_ex_end <= extent_logical_end(sbi, &ex))
+			goto adjust_bex;
+
+		ex.fe_logical = ac->ac_o_ex.fe_logical;
+adjust_bex:
+		ac->ac_b_ex.fe_logical = ex.fe_logical;
 
-		ac->ac_b_ex.fe_logical = ac->ac_o_ex.fe_logical -
-			EXT4_NUM_B2C(sbi, win);
 		BUG_ON(ac->ac_o_ex.fe_logical < ac->ac_b_ex.fe_logical);
-		BUG_ON(ac->ac_o_ex.fe_len > ac->ac_b_ex.fe_len);
+		BUG_ON(extent_logical_end(sbi, &ex) > orig_goal_end);
 	}
 
 	/* preallocation can change ac_b_ex, thus we store actually
@@ -4647,6 +4760,8 @@
 
 	ei = EXT4_I(ac->ac_inode);
 	grp = ext4_get_group_info(sb, ac->ac_b_ex.fe_group);
+	if (!grp)
+		return;
 
 	pa->pa_obj_lock = &ei->i_prealloc_lock;
 	pa->pa_inode = ac->ac_inode;
@@ -4700,6 +4815,8 @@
 	atomic_add(pa->pa_free, &EXT4_SB(sb)->s_mb_preallocated);
 
 	grp = ext4_get_group_info(sb, ac->ac_b_ex.fe_group);
+	if (!grp)
+		return;
 	lg = ac->ac_lg;
 	BUG_ON(lg == NULL);
 
@@ -4795,7 +4912,11 @@
 	trace_ext4_mb_release_group_pa(sb, pa);
 	BUG_ON(pa->pa_deleted == 0);
 	ext4_get_group_no_and_offset(sb, pa->pa_pstart, &group, &bit);
-	BUG_ON(group != e4b->bd_group && pa->pa_len != 0);
+	if (unlikely(group != e4b->bd_group && pa->pa_len != 0)) {
+		ext4_warning(sb, "bad group: expected %u, group %u, pa_start %llu",
+			     e4b->bd_group, group, pa->pa_pstart);
+		return 0;
+	}
 	mb_free_blocks(pa->pa_inode, e4b, bit, pa->pa_len);
 	atomic_add(pa->pa_len, &EXT4_SB(sb)->s_mb_discarded);
 	trace_ext4_mballoc_discard(sb, NULL, group, bit, pa->pa_len);
@@ -4814,7 +4935,7 @@
  */
 static noinline_for_stack int
 ext4_mb_discard_group_preallocations(struct super_block *sb,
-					ext4_group_t group, int needed)
+				     ext4_group_t group, int *busy)
 {
 	struct ext4_group_info *grp = ext4_get_group_info(sb, group);
 	struct buffer_head *bitmap_bh = NULL;
@@ -4822,9 +4943,10 @@
 	struct list_head list;
 	struct ext4_buddy e4b;
 	int err;
-	int busy = 0;
-	int free, free_total = 0;
+	int free = 0;
 
+	if (!grp)
+		return 0;
 	mb_debug(sb, "discard preallocation for group %u\n", group);
 	if (list_empty(&grp->bb_prealloc_list))
 		goto out_dbg;
@@ -4846,19 +4968,14 @@
 		goto out_dbg;
 	}
 
-	if (needed == 0)
-		needed = EXT4_CLUSTERS_PER_GROUP(sb) + 1;
-
 	INIT_LIST_HEAD(&list);
-repeat:
-	free = 0;
 	ext4_lock_group(sb, group);
 	list_for_each_entry_safe(pa, tmp,
 				&grp->bb_prealloc_list, pa_group_list) {
 		spin_lock(&pa->pa_lock);
 		if (atomic_read(&pa->pa_count)) {
 			spin_unlock(&pa->pa_lock);
-			busy = 1;
+			*busy = 1;
 			continue;
 		}
 		if (pa->pa_deleted) {
@@ -4898,22 +5015,13 @@
 		call_rcu(&(pa)->u.pa_rcu, ext4_mb_pa_callback);
 	}
 
-	free_total += free;
-
-	/* if we still need more blocks and some PAs were used, try again */
-	if (free_total < needed && busy) {
-		ext4_unlock_group(sb, group);
-		cond_resched();
-		busy = 0;
-		goto repeat;
-	}
 	ext4_unlock_group(sb, group);
 	ext4_mb_unload_buddy(&e4b);
 	put_bh(bitmap_bh);
 out_dbg:
 	mb_debug(sb, "discarded (%d) blocks preallocated for group %u bb_free (%d)\n",
-		 free_total, group, grp->bb_free);
-	return free_total;
+		 free, group, grp->bb_free);
+	return free;
 }
 
 /*
@@ -5076,6 +5184,9 @@
 		struct ext4_prealloc_space *pa;
 		ext4_grpblk_t start;
 		struct list_head *cur;
+
+		if (!grp)
+			continue;
 		ext4_lock_group(sb, i);
 		list_for_each(cur, &grp->bb_prealloc_list) {
 			pa = list_entry(cur, struct ext4_prealloc_space,
@@ -5147,6 +5258,7 @@
 	struct ext4_sb_info *sbi = EXT4_SB(ac->ac_sb);
 	int bsbits = ac->ac_sb->s_blocksize_bits;
 	loff_t size, isize;
+	bool inode_pa_eligible, group_pa_eligible;
 
 	if (!(ac->ac_flags & EXT4_MB_HINT_DATA))
 		return;
@@ -5154,25 +5266,27 @@
 	if (unlikely(ac->ac_flags & EXT4_MB_HINT_GOAL_ONLY))
 		return;
 
-	size = ac->ac_o_ex.fe_logical + EXT4_C2B(sbi, ac->ac_o_ex.fe_len);
+	group_pa_eligible = sbi->s_mb_group_prealloc > 0;
+	inode_pa_eligible = true;
+	size = extent_logical_end(sbi, &ac->ac_o_ex);
 	isize = (i_size_read(ac->ac_inode) + ac->ac_sb->s_blocksize - 1)
 		>> bsbits;
 
+	/* No point in using inode preallocation for closed files */
 	if ((size == isize) && !ext4_fs_is_busy(sbi) &&
-	    !inode_is_open_for_write(ac->ac_inode)) {
-		ac->ac_flags |= EXT4_MB_HINT_NOPREALLOC;
-		return;
-	}
+	    !inode_is_open_for_write(ac->ac_inode))
+		inode_pa_eligible = false;
 
-	if (sbi->s_mb_group_prealloc <= 0) {
-		ac->ac_flags |= EXT4_MB_STREAM_ALLOC;
-		return;
-	}
-
-	/* don't use group allocation for large files */
 	size = max(size, isize);
-	if (size > sbi->s_mb_stream_request) {
-		ac->ac_flags |= EXT4_MB_STREAM_ALLOC;
+	/* Don't use group allocation for large files */
+	if (size > sbi->s_mb_stream_request)
+		group_pa_eligible = false;
+
+	if (!group_pa_eligible) {
+		if (inode_pa_eligible)
+			ac->ac_flags |= EXT4_MB_STREAM_ALLOC;
+		else
+			ac->ac_flags |= EXT4_MB_HINT_NOPREALLOC;
 		return;
 	}
 
@@ -5455,13 +5569,24 @@
 {
 	ext4_group_t i, ngroups = ext4_get_groups_count(sb);
 	int ret;
-	int freed = 0;
+	int freed = 0, busy = 0;
+	int retry = 0;
 
 	trace_ext4_mb_discard_preallocations(sb, needed);
+
+	if (needed == 0)
+		needed = EXT4_CLUSTERS_PER_GROUP(sb) + 1;
+ repeat:
 	for (i = 0; i < ngroups && needed > 0; i++) {
-		ret = ext4_mb_discard_group_preallocations(sb, i, needed);
+		ret = ext4_mb_discard_group_preallocations(sb, i, &busy);
 		freed += ret;
 		needed -= ret;
+		cond_resched();
+	}
+
+	if (needed > 0 && busy && ++retry < 3) {
+		busy = 0;
+		goto repeat;
 	}
 
 	return freed;
@@ -5491,8 +5616,73 @@
 	return ret;
 }
 
-static ext4_fsblk_t ext4_mb_new_blocks_simple(handle_t *handle,
-				struct ext4_allocation_request *ar, int *errp);
+/*
+ * Simple allocator for Ext4 fast commit replay path. It searches for blocks
+ * linearly starting at the goal block and also excludes the blocks which
+ * are going to be in use after fast commit replay.
+ */
+static ext4_fsblk_t
+ext4_mb_new_blocks_simple(struct ext4_allocation_request *ar, int *errp)
+{
+	struct buffer_head *bitmap_bh;
+	struct super_block *sb = ar->inode->i_sb;
+	struct ext4_sb_info *sbi = EXT4_SB(sb);
+	ext4_group_t group, nr;
+	ext4_grpblk_t blkoff;
+	ext4_grpblk_t max = EXT4_CLUSTERS_PER_GROUP(sb);
+	ext4_grpblk_t i = 0;
+	ext4_fsblk_t goal, block;
+	struct ext4_super_block *es = EXT4_SB(sb)->s_es;
+
+	goal = ar->goal;
+	if (goal < le32_to_cpu(es->s_first_data_block) ||
+			goal >= ext4_blocks_count(es))
+		goal = le32_to_cpu(es->s_first_data_block);
+
+	ar->len = 0;
+	ext4_get_group_no_and_offset(sb, goal, &group, &blkoff);
+	for (nr = ext4_get_groups_count(sb); nr > 0; nr--) {
+		bitmap_bh = ext4_read_block_bitmap(sb, group);
+		if (IS_ERR(bitmap_bh)) {
+			*errp = PTR_ERR(bitmap_bh);
+			pr_warn("Failed to read block bitmap\n");
+			return 0;
+		}
+
+		while (1) {
+			i = mb_find_next_zero_bit(bitmap_bh->b_data, max,
+						blkoff);
+			if (i >= max)
+				break;
+			if (ext4_fc_replay_check_excluded(sb,
+				ext4_group_first_block_no(sb, group) +
+				EXT4_C2B(sbi, i))) {
+				blkoff = i + 1;
+			} else
+				break;
+		}
+		brelse(bitmap_bh);
+		if (i < max)
+			break;
+
+		if (++group >= ext4_get_groups_count(sb))
+			group = 0;
+
+		blkoff = 0;
+	}
+
+	if (i >= max) {
+		*errp = -ENOSPC;
+		return 0;
+	}
+
+	block = ext4_group_first_block_no(sb, group) + EXT4_C2B(sbi, i);
+	ext4_mb_mark_bb(sb, block, 1, 1);
+	ar->len = 1;
+
+	*errp = 0;
+	return block;
+}
 
 /*
  * Main entry point into mballoc to allocate blocks
@@ -5508,6 +5698,7 @@
 	ext4_fsblk_t block = 0;
 	unsigned int inquota = 0;
 	unsigned int reserv_clstrs = 0;
+	int retries = 0;
 	u64 seq;
 
 	might_sleep();
@@ -5516,7 +5707,7 @@
 
 	trace_ext4_request_blocks(ar);
 	if (sbi->s_mount_state & EXT4_FC_REPLAY)
-		return ext4_mb_new_blocks_simple(handle, ar, errp);
+		return ext4_mb_new_blocks_simple(ar, errp);
 
 	/* Allow to use superuser reservation for quota file */
 	if (ext4_is_quota_file(ar->inode))
@@ -5610,7 +5801,8 @@
 			ar->len = ac->ac_b_ex.fe_len;
 		}
 	} else {
-		if (ext4_mb_discard_preallocations_should_retry(sb, ac, &seq))
+		if (++retries < 3 &&
+		    ext4_mb_discard_preallocations_should_retry(sb, ac, &seq))
 			goto repeat;
 		/*
 		 * If block allocation fails then the pa allocated above
@@ -5745,61 +5937,6 @@
 	return 0;
 }
 
-/*
- * Simple allocator for Ext4 fast commit replay path. It searches for blocks
- * linearly starting at the goal block and also excludes the blocks which
- * are going to be in use after fast commit replay.
- */
-static ext4_fsblk_t ext4_mb_new_blocks_simple(handle_t *handle,
-				struct ext4_allocation_request *ar, int *errp)
-{
-	struct buffer_head *bitmap_bh;
-	struct super_block *sb = ar->inode->i_sb;
-	ext4_group_t group;
-	ext4_grpblk_t blkoff;
-	int i = sb->s_blocksize;
-	ext4_fsblk_t goal, block;
-	struct ext4_super_block *es = EXT4_SB(sb)->s_es;
-
-	goal = ar->goal;
-	if (goal < le32_to_cpu(es->s_first_data_block) ||
-			goal >= ext4_blocks_count(es))
-		goal = le32_to_cpu(es->s_first_data_block);
-
-	ar->len = 0;
-	ext4_get_group_no_and_offset(sb, goal, &group, &blkoff);
-	for (; group < ext4_get_groups_count(sb); group++) {
-		bitmap_bh = ext4_read_block_bitmap(sb, group);
-		if (IS_ERR(bitmap_bh)) {
-			*errp = PTR_ERR(bitmap_bh);
-			pr_warn("Failed to read block bitmap\n");
-			return 0;
-		}
-
-		ext4_get_group_no_and_offset(sb,
-			max(ext4_group_first_block_no(sb, group), goal),
-			NULL, &blkoff);
-		i = mb_find_next_zero_bit(bitmap_bh->b_data, sb->s_blocksize,
-						blkoff);
-		brelse(bitmap_bh);
-		if (i >= sb->s_blocksize)
-			continue;
-		if (ext4_fc_replay_check_excluded(sb,
-			ext4_group_first_block_no(sb, group) + i))
-			continue;
-		break;
-	}
-
-	if (group >= ext4_get_groups_count(sb) && i >= sb->s_blocksize)
-		return 0;
-
-	block = ext4_group_first_block_no(sb, group) + i;
-	ext4_mb_mark_bb(sb, block, 1, 1);
-	ar->len = 1;
-
-	return block;
-}
-
 static void ext4_free_blocks_simple(struct inode *inode, ext4_fsblk_t block,
 					unsigned long count)
 {
@@ -5842,7 +5979,8 @@
 }
 
 /**
- * ext4_free_blocks() -- Free given blocks and update quota
+ * ext4_mb_clear_bb() -- helper function for freeing blocks.
+ *			Used by ext4_free_blocks()
  * @handle:		handle for this transaction
  * @inode:		inode
  * @bh:			optional buffer of the block to be freed
@@ -5850,13 +5988,14 @@
  * @count:		number of blocks to be freed
  * @flags:		flags used by ext4_free_blocks
  */
-void ext4_free_blocks(handle_t *handle, struct inode *inode,
-		      struct buffer_head *bh, ext4_fsblk_t block,
-		      unsigned long count, int flags)
+static void ext4_mb_clear_bb(handle_t *handle, struct inode *inode,
+			       ext4_fsblk_t block, unsigned long count,
+			       int flags)
 {
 	struct buffer_head *bitmap_bh = NULL;
 	struct super_block *sb = inode->i_sb;
 	struct ext4_group_desc *gdp;
+	struct ext4_group_info *grp;
 	unsigned int overflow;
 	ext4_grpblk_t bit;
 	struct buffer_head *gd_bh;
@@ -5869,86 +6008,21 @@
 
 	sbi = EXT4_SB(sb);
 
-	if (sbi->s_mount_state & EXT4_FC_REPLAY) {
-		ext4_free_blocks_simple(inode, block, count);
-		return;
-	}
-
-	might_sleep();
-	if (bh) {
-		if (block)
-			BUG_ON(block != bh->b_blocknr);
-		else
-			block = bh->b_blocknr;
-	}
-
 	if (!(flags & EXT4_FREE_BLOCKS_VALIDATED) &&
 	    !ext4_inode_block_valid(inode, block, count)) {
-		ext4_error(sb, "Freeing blocks not in datazone - "
-			   "block = %llu, count = %lu", block, count);
+		ext4_error(sb, "Freeing blocks in system zone - "
+			   "Block = %llu, count = %lu", block, count);
+		/* err = 0. ext4_std_error should be a no op */
 		goto error_return;
 	}
-
-	ext4_debug("freeing block %llu\n", block);
-	trace_ext4_free_blocks(inode, block, count, flags);
-
-	if (bh && (flags & EXT4_FREE_BLOCKS_FORGET)) {
-		BUG_ON(count > 1);
-
-		ext4_forget(handle, flags & EXT4_FREE_BLOCKS_METADATA,
-			    inode, bh, block);
-	}
-
-	/*
-	 * If the extent to be freed does not begin on a cluster
-	 * boundary, we need to deal with partial clusters at the
-	 * beginning and end of the extent.  Normally we will free
-	 * blocks at the beginning or the end unless we are explicitly
-	 * requested to avoid doing so.
-	 */
-	overflow = EXT4_PBLK_COFF(sbi, block);
-	if (overflow) {
-		if (flags & EXT4_FREE_BLOCKS_NOFREE_FIRST_CLUSTER) {
-			overflow = sbi->s_cluster_ratio - overflow;
-			block += overflow;
-			if (count > overflow)
-				count -= overflow;
-			else
-				return;
-		} else {
-			block -= overflow;
-			count += overflow;
-		}
-	}
-	overflow = EXT4_LBLK_COFF(sbi, count);
-	if (overflow) {
-		if (flags & EXT4_FREE_BLOCKS_NOFREE_LAST_CLUSTER) {
-			if (count > overflow)
-				count -= overflow;
-			else
-				return;
-		} else
-			count += sbi->s_cluster_ratio - overflow;
-	}
-
-	if (!bh && (flags & EXT4_FREE_BLOCKS_FORGET)) {
-		int i;
-		int is_metadata = flags & EXT4_FREE_BLOCKS_METADATA;
-
-		for (i = 0; i < count; i++) {
-			cond_resched();
-			if (is_metadata)
-				bh = sb_find_get_block(inode->i_sb, block + i);
-			ext4_forget(handle, is_metadata, inode, bh, block + i);
-		}
-	}
+	flags |= EXT4_FREE_BLOCKS_VALIDATED;
 
 do_more:
 	overflow = 0;
 	ext4_get_group_no_and_offset(sb, block, &block_group, &bit);
 
-	if (unlikely(EXT4_MB_GRP_BBITMAP_CORRUPT(
-			ext4_get_group_info(sb, block_group))))
+	grp = ext4_get_group_info(sb, block_group);
+	if (unlikely(!grp || EXT4_MB_GRP_BBITMAP_CORRUPT(grp)))
 		return;
 
 	/*
@@ -5959,6 +6033,8 @@
 		overflow = EXT4_C2B(sbi, bit) + count -
 			EXT4_BLOCKS_PER_GROUP(sb);
 		count -= overflow;
+		/* The range changed so it's no longer validated */
+		flags &= ~EXT4_FREE_BLOCKS_VALIDATED;
 	}
 	count_clusters = EXT4_NUM_B2C(sbi, count);
 	bitmap_bh = ext4_read_block_bitmap(sb, block_group);
@@ -5973,13 +6049,8 @@
 		goto error_return;
 	}
 
-	if (in_range(ext4_block_bitmap(sb, gdp), block, count) ||
-	    in_range(ext4_inode_bitmap(sb, gdp), block, count) ||
-	    in_range(block, ext4_inode_table(sb, gdp),
-		     sbi->s_itb_per_group) ||
-	    in_range(block + count - 1, ext4_inode_table(sb, gdp),
-		     sbi->s_itb_per_group)) {
-
+	if (!(flags & EXT4_FREE_BLOCKS_VALIDATED) &&
+	    !ext4_inode_block_valid(inode, block, count)) {
 		ext4_error(sb, "Freeing blocks in system zone - "
 			   "Block = %llu, count = %lu", block, count);
 		/* err = 0. ext4_std_error should be a no op */
@@ -6046,15 +6117,16 @@
 		 * them with group lock_held
 		 */
 		if (test_opt(sb, DISCARD)) {
-			err = ext4_issue_discard(sb, block_group, bit, count,
-						 NULL);
+			err = ext4_issue_discard(sb, block_group, bit,
+						 count_clusters, NULL);
 			if (err && err != -EOPNOTSUPP)
 				ext4_msg(sb, KERN_WARNING, "discard request in"
-					 " group:%d block:%d count:%lu failed"
+					 " group:%u block:%d count:%lu failed"
 					 " with %d", block_group, bit, count,
 					 err);
-		} else
-			EXT4_MB_GRP_CLEAR_TRIMMED(e4b.bd_info);
+		}
+
+		EXT4_MB_GRP_CLEAR_TRIMMED(e4b.bd_info);
 
 		ext4_lock_group(sb, block_group);
 		mb_clear_bits(bitmap_bh->b_data, bit, count_clusters);
@@ -6102,6 +6174,8 @@
 		block += count;
 		count = overflow;
 		put_bh(bitmap_bh);
+		/* The range changed so it's no longer validated */
+		flags &= ~EXT4_FREE_BLOCKS_VALIDATED;
 		goto do_more;
 	}
 error_return:
@@ -6111,6 +6185,109 @@
 }
 
 /**
+ * ext4_free_blocks() -- Free given blocks and update quota
+ * @handle:		handle for this transaction
+ * @inode:		inode
+ * @bh:			optional buffer of the block to be freed
+ * @block:		starting physical block to be freed
+ * @count:		number of blocks to be freed
+ * @flags:		flags used by ext4_free_blocks
+ */
+void ext4_free_blocks(handle_t *handle, struct inode *inode,
+		      struct buffer_head *bh, ext4_fsblk_t block,
+		      unsigned long count, int flags)
+{
+	struct super_block *sb = inode->i_sb;
+	unsigned int overflow;
+	struct ext4_sb_info *sbi;
+
+	sbi = EXT4_SB(sb);
+
+	if (bh) {
+		if (block)
+			BUG_ON(block != bh->b_blocknr);
+		else
+			block = bh->b_blocknr;
+	}
+
+	if (sbi->s_mount_state & EXT4_FC_REPLAY) {
+		ext4_free_blocks_simple(inode, block, EXT4_NUM_B2C(sbi, count));
+		return;
+	}
+
+	might_sleep();
+
+	if (!(flags & EXT4_FREE_BLOCKS_VALIDATED) &&
+	    !ext4_inode_block_valid(inode, block, count)) {
+		ext4_error(sb, "Freeing blocks not in datazone - "
+			   "block = %llu, count = %lu", block, count);
+		return;
+	}
+	flags |= EXT4_FREE_BLOCKS_VALIDATED;
+
+	ext4_debug("freeing block %llu\n", block);
+	trace_ext4_free_blocks(inode, block, count, flags);
+
+	if (bh && (flags & EXT4_FREE_BLOCKS_FORGET)) {
+		BUG_ON(count > 1);
+
+		ext4_forget(handle, flags & EXT4_FREE_BLOCKS_METADATA,
+			    inode, bh, block);
+	}
+
+	/*
+	 * If the extent to be freed does not begin on a cluster
+	 * boundary, we need to deal with partial clusters at the
+	 * beginning and end of the extent.  Normally we will free
+	 * blocks at the beginning or the end unless we are explicitly
+	 * requested to avoid doing so.
+	 */
+	overflow = EXT4_PBLK_COFF(sbi, block);
+	if (overflow) {
+		if (flags & EXT4_FREE_BLOCKS_NOFREE_FIRST_CLUSTER) {
+			overflow = sbi->s_cluster_ratio - overflow;
+			block += overflow;
+			if (count > overflow)
+				count -= overflow;
+			else
+				return;
+		} else {
+			block -= overflow;
+			count += overflow;
+		}
+		/* The range changed so it's no longer validated */
+		flags &= ~EXT4_FREE_BLOCKS_VALIDATED;
+	}
+	overflow = EXT4_LBLK_COFF(sbi, count);
+	if (overflow) {
+		if (flags & EXT4_FREE_BLOCKS_NOFREE_LAST_CLUSTER) {
+			if (count > overflow)
+				count -= overflow;
+			else
+				return;
+		} else
+			count += sbi->s_cluster_ratio - overflow;
+		/* The range changed so it's no longer validated */
+		flags &= ~EXT4_FREE_BLOCKS_VALIDATED;
+	}
+
+	if (!bh && (flags & EXT4_FREE_BLOCKS_FORGET)) {
+		int i;
+		int is_metadata = flags & EXT4_FREE_BLOCKS_METADATA;
+
+		for (i = 0; i < count; i++) {
+			cond_resched();
+			if (is_metadata)
+				bh = sb_find_get_block(inode->i_sb, block + i);
+			ext4_forget(handle, is_metadata, inode, bh, block + i);
+		}
+	}
+
+	ext4_mb_clear_bb(handle, inode, block, count, flags);
+	return;
+}
+
+/**
  * ext4_group_add_blocks() -- Add given blocks to an existing group
  * @handle:			handle to this transaction
  * @sb:				super block
@@ -6166,11 +6343,7 @@
 		goto error_return;
 	}
 
-	if (in_range(ext4_block_bitmap(sb, desc), block, count) ||
-	    in_range(ext4_inode_bitmap(sb, desc), block, count) ||
-	    in_range(block, ext4_inode_table(sb, desc), sbi->s_itb_per_group) ||
-	    in_range(block + count - 1, ext4_inode_table(sb, desc),
-		     sbi->s_itb_per_group)) {
+	if (!ext4_sb_block_valid(sb, NULL, block, count)) {
 		ext4_error(sb, "Adding blocks in system zones - "
 			   "Block = %llu, count = %lu",
 			   block, count);
@@ -6291,19 +6464,45 @@
 	return ret;
 }
 
+static ext4_grpblk_t ext4_last_grp_cluster(struct super_block *sb,
+					   ext4_group_t grp)
+{
+	unsigned long nr_clusters_in_group;
+
+	if (grp < (ext4_get_groups_count(sb) - 1))
+		nr_clusters_in_group = EXT4_CLUSTERS_PER_GROUP(sb);
+	else
+		nr_clusters_in_group = (ext4_blocks_count(EXT4_SB(sb)->s_es) -
+					ext4_group_first_block_no(sb, grp))
+				       >> EXT4_CLUSTER_BITS(sb);
+
+	return nr_clusters_in_group - 1;
+}
+
+static bool ext4_trim_interrupted(void)
+{
+	return fatal_signal_pending(current) || freezing(current);
+}
+
 static int ext4_try_to_trim_range(struct super_block *sb,
 		struct ext4_buddy *e4b, ext4_grpblk_t start,
 		ext4_grpblk_t max, ext4_grpblk_t minblocks)
 __acquires(ext4_group_lock_ptr(sb, e4b->bd_group))
 __releases(ext4_group_lock_ptr(sb, e4b->bd_group))
 {
-	ext4_grpblk_t next, count, free_count;
+	ext4_grpblk_t next, count, free_count, last, origin_start;
+	bool set_trimmed = false;
 	void *bitmap;
-	int ret = 0;
 
+	if (unlikely(EXT4_MB_GRP_BBITMAP_CORRUPT(e4b->bd_info)))
+		return 0;
+
+	last = ext4_last_grp_cluster(sb, e4b->bd_group);
 	bitmap = e4b->bd_bitmap;
-	start = (e4b->bd_info->bb_first_free > start) ?
-		e4b->bd_info->bb_first_free : start;
+	if (start == 0 && max >= last)
+		set_trimmed = true;
+	origin_start = start;
+	start = max(e4b->bd_info->bb_first_free, start);
 	count = 0;
 	free_count = 0;
 
@@ -6311,22 +6510,23 @@
 		start = mb_find_next_zero_bit(bitmap, max + 1, start);
 		if (start > max)
 			break;
-		next = mb_find_next_bit(bitmap, max + 1, start);
+
+		next = mb_find_next_bit(bitmap, last + 1, start);
+		if (origin_start == 0 && next >= last)
+			set_trimmed = true;
 
 		if ((next - start) >= minblocks) {
-			ret = ext4_trim_extent(sb, start, next - start, e4b);
+			int ret = ext4_trim_extent(sb, start, next - start, e4b);
+
 			if (ret && ret != -EOPNOTSUPP)
-				break;
-			ret = 0;
+				return count;
 			count += next - start;
 		}
 		free_count += next - start;
 		start = next + 1;
 
-		if (fatal_signal_pending(current)) {
-			count = -ERESTARTSYS;
-			break;
-		}
+		if (ext4_trim_interrupted())
+			return count;
 
 		if (need_resched()) {
 			ext4_unlock_group(sb, e4b->bd_group);
@@ -6338,6 +6538,9 @@
 			break;
 	}
 
+	if (set_trimmed)
+		EXT4_MB_GRP_SET_TRIMMED(e4b->bd_info);
+
 	return count;
 }
 
@@ -6374,13 +6577,10 @@
 	ext4_lock_group(sb, group);
 
 	if (!EXT4_MB_GRP_WAS_TRIMMED(e4b.bd_info) ||
-	    minblocks < atomic_read(&EXT4_SB(sb)->s_last_trim_minblks)) {
+	    minblocks < EXT4_SB(sb)->s_last_trim_minblks)
 		ret = ext4_try_to_trim_range(sb, &e4b, start, max, minblocks);
-		if (ret >= 0)
-			EXT4_MB_GRP_SET_TRIMMED(e4b.bd_info);
-	} else {
+	else
 		ret = 0;
-	}
 
 	ext4_unlock_group(sb, group);
 	ext4_mb_unload_buddy(&e4b);
@@ -6405,6 +6605,7 @@
  */
 int ext4_trim_fs(struct super_block *sb, struct fstrim_range *range)
 {
+	struct request_queue *q = bdev_get_queue(sb->s_bdev);
 	struct ext4_group_info *grp;
 	ext4_group_t group, first_group, last_group;
 	ext4_grpblk_t cnt = 0, first_cluster, last_cluster;
@@ -6423,7 +6624,14 @@
 	    start >= max_blks ||
 	    range->len < sb->s_blocksize)
 		return -EINVAL;
-	if (end >= max_blks)
+	/* No point to try to trim less than discard granularity */
+	if (range->minlen < q->limits.discard_granularity) {
+		minlen = EXT4_NUM_B2C(EXT4_SB(sb),
+			q->limits.discard_granularity >> sb->s_blocksize_bits);
+		if (minlen > EXT4_CLUSTERS_PER_GROUP(sb))
+			goto out;
+	}
+	if (end >= max_blks - 1)
 		end = max_blks - 1;
 	if (end <= first_data_blk)
 		goto out;
@@ -6440,7 +6648,11 @@
 	end = EXT4_CLUSTERS_PER_GROUP(sb) - 1;
 
 	for (group = first_group; group <= last_group; group++) {
+		if (ext4_trim_interrupted())
+			break;
 		grp = ext4_get_group_info(sb, group);
+		if (!grp)
+			continue;
 		/* We only do this if the grp has never been initialized */
 		if (unlikely(EXT4_MB_GRP_NEED_INIT(grp))) {
 			ret = ext4_mb_init_group(sb, group, GFP_NOFS);
@@ -6456,10 +6668,9 @@
 		 */
 		if (group == last_group)
 			end = last_cluster;
-
 		if (grp->bb_free >= minlen) {
 			cnt = ext4_trim_all_free(sb, group, first_cluster,
-						end, minlen);
+						 end, minlen);
 			if (cnt < 0) {
 				ret = cnt;
 				break;
@@ -6475,7 +6686,7 @@
 	}
 
 	if (!ret)
-		atomic_set(&EXT4_SB(sb)->s_last_trim_minblks, minlen);
+		EXT4_SB(sb)->s_last_trim_minblks = minlen;
 
 out:
 	range->len = EXT4_C2B(EXT4_SB(sb), trimmed) << sb->s_blocksize_bits;
@@ -6487,13 +6698,14 @@
 ext4_mballoc_query_range(
 	struct super_block		*sb,
 	ext4_group_t			group,
-	ext4_grpblk_t			start,
+	ext4_grpblk_t			first,
 	ext4_grpblk_t			end,
+	ext4_mballoc_query_range_fn	meta_formatter,
 	ext4_mballoc_query_range_fn	formatter,
 	void				*priv)
 {
 	void				*bitmap;
-	ext4_grpblk_t			next;
+	ext4_grpblk_t			start, next;
 	struct ext4_buddy		e4b;
 	int				error;
 
@@ -6504,11 +6716,19 @@
 
 	ext4_lock_group(sb, group);
 
-	start = (e4b.bd_info->bb_first_free > start) ?
-		e4b.bd_info->bb_first_free : start;
+	start = max(e4b.bd_info->bb_first_free, first);
 	if (end >= EXT4_CLUSTERS_PER_GROUP(sb))
 		end = EXT4_CLUSTERS_PER_GROUP(sb) - 1;
-
+	if (meta_formatter && start != first) {
+		if (start > end)
+			start = end;
+		ext4_unlock_group(sb, group);
+		error = meta_formatter(sb, group, first, start - first,
+				       priv);
+		if (error)
+			goto out_unload;
+		ext4_lock_group(sb, group);
+	}
 	while (start <= end) {
 		start = mb_find_next_zero_bit(bitmap, end + 1, start);
 		if (start > end)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/mballoc.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/mballoc.h
@@ -181,8 +181,8 @@
 	ext4_group_t ac_last_optimal_group;
 	__u32 ac_groups_considered;
 	__u32 ac_flags;		/* allocation hints */
+	__u32 ac_groups_linear_remaining;
 	__u16 ac_groups_scanned;
-	__u16 ac_groups_linear_remaining;
 	__u16 ac_found;
 	__u16 ac_tail;
 	__u16 ac_buddy;
@@ -219,6 +219,20 @@
 		(fex->fe_start << EXT4_SB(sb)->s_cluster_bits);
 }
 
+static inline loff_t extent_logical_end(struct ext4_sb_info *sbi,
+					struct ext4_free_extent *fex)
+{
+	/* Use loff_t to avoid end exceeding ext4_lblk_t max. */
+	return (loff_t)fex->fe_logical + EXT4_C2B(sbi, fex->fe_len);
+}
+
+static inline loff_t pa_logical_end(struct ext4_sb_info *sbi,
+				    struct ext4_prealloc_space *pa)
+{
+	/* Use loff_t to avoid end exceeding ext4_lblk_t max. */
+	return (loff_t)pa->pa_lstart + EXT4_C2B(sbi, pa->pa_len);
+}
+
 typedef int (*ext4_mballoc_query_range_fn)(
 	struct super_block		*sb,
 	ext4_group_t			agno,
@@ -232,6 +246,7 @@
 	ext4_group_t			agno,
 	ext4_grpblk_t			start,
 	ext4_grpblk_t			end,
+	ext4_mballoc_query_range_fn	meta_formatter,
 	ext4_mballoc_query_range_fn	formatter,
 	void				*priv);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/migrate.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/migrate.c
@@ -417,7 +417,7 @@
 	struct inode *tmp_inode = NULL;
 	struct migrate_struct lb;
 	unsigned long max_entries;
-	__u32 goal;
+	__u32 goal, tmp_csum_seed;
 	uid_t owner[2];
 
 	/*
@@ -425,7 +425,8 @@
 	 * already is extent-based, error out.
 	 */
 	if (!ext4_has_feature_extents(inode->i_sb) ||
-	    (ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS)))
+	    ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS) ||
+	    ext4_has_inline_data(inode))
 		return -EINVAL;
 
 	if (S_ISLNK(inode->i_mode) && inode->i_blocks == 0)
@@ -437,12 +438,12 @@
 	percpu_down_write(&sbi->s_writepages_rwsem);
 
 	/*
-	 * Worst case we can touch the allocation bitmaps, a bgd
-	 * block, and a block to link in the orphan list.  We do need
-	 * need to worry about credits for modifying the quota inode.
+	 * Worst case we can touch the allocation bitmaps and a block
+	 * group descriptor block.  We do need need to worry about
+	 * credits for modifying the quota inode.
 	 */
 	handle = ext4_journal_start(inode, EXT4_HT_MIGRATE,
-		4 + EXT4_MAXQUOTAS_TRANS_BLOCKS(inode->i_sb));
+		3 + EXT4_MAXQUOTAS_TRANS_BLOCKS(inode->i_sb));
 
 	if (IS_ERR(handle)) {
 		retval = PTR_ERR(handle);
@@ -459,6 +460,14 @@
 		ext4_journal_stop(handle);
 		goto out_unlock;
 	}
+	/*
+	 * Use the correct seed for checksum (i.e. the seed from 'inode').  This
+	 * is so that the metadata blocks will have the correct checksum after
+	 * the migration.
+	 */
+	ei = EXT4_I(inode);
+	tmp_csum_seed = EXT4_I(tmp_inode)->i_csum_seed;
+	EXT4_I(tmp_inode)->i_csum_seed = ei->i_csum_seed;
 	i_size_write(tmp_inode, i_size_read(inode));
 	/*
 	 * Set the i_nlink to zero so it will be deleted later
@@ -467,7 +476,6 @@
 	clear_nlink(tmp_inode);
 
 	ext4_ext_tree_init(handle, tmp_inode);
-	ext4_orphan_add(handle, tmp_inode);
 	ext4_journal_stop(handle);
 
 	/*
@@ -492,17 +500,10 @@
 
 	handle = ext4_journal_start(inode, EXT4_HT_MIGRATE, 1);
 	if (IS_ERR(handle)) {
-		/*
-		 * It is impossible to update on-disk structures without
-		 * a handle, so just rollback in-core changes and live other
-		 * work to orphan_list_cleanup()
-		 */
-		ext4_orphan_del(NULL, tmp_inode);
 		retval = PTR_ERR(handle);
 		goto out_tmp_inode;
 	}
 
-	ei = EXT4_I(inode);
 	i_data = ei->i_data;
 	memset(&lb, 0, sizeof(lb));
 
@@ -576,6 +577,7 @@
 	 * the inode is not visible to user space.
 	 */
 	tmp_inode->i_blocks = 0;
+	EXT4_I(tmp_inode)->i_csum_seed = tmp_csum_seed;
 
 	/* Reset the extent details */
 	ext4_ext_tree_init(handle, tmp_inode);
@@ -661,8 +663,8 @@
 	if (unlikely(ret2 && !ret))
 		ret = ret2;
 errout:
-	ext4_journal_stop(handle);
 	up_write(&EXT4_I(inode)->i_data_sem);
+	ext4_journal_stop(handle);
 out_unlock:
 	percpu_up_write(&sbi->s_writepages_rwsem);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/mmp.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/mmp.c
@@ -39,28 +39,36 @@
  * Write the MMP block using REQ_SYNC to try to get the block on-disk
  * faster.
  */
-static int write_mmp_block(struct super_block *sb, struct buffer_head *bh)
+static int write_mmp_block_thawed(struct super_block *sb,
+				  struct buffer_head *bh)
 {
 	struct mmp_struct *mmp = (struct mmp_struct *)(bh->b_data);
 
-	/*
-	 * We protect against freezing so that we don't create dirty buffers
-	 * on frozen filesystem.
-	 */
-	sb_start_write(sb);
 	ext4_mmp_csum_set(sb, mmp);
 	lock_buffer(bh);
 	bh->b_end_io = end_buffer_write_sync;
 	get_bh(bh);
 	submit_bh(REQ_OP_WRITE, REQ_SYNC | REQ_META | REQ_PRIO, bh);
 	wait_on_buffer(bh);
-	sb_end_write(sb);
 	if (unlikely(!buffer_uptodate(bh)))
 		return -EIO;
-
 	return 0;
 }
 
+static int write_mmp_block(struct super_block *sb, struct buffer_head *bh)
+{
+	int err;
+
+	/*
+	 * We protect against freezing so that we don't create dirty buffers
+	 * on frozen filesystem.
+	 */
+	sb_start_write(sb);
+	err = write_mmp_block_thawed(sb, bh);
+	sb_end_write(sb);
+	return err;
+}
+
 /*
  * Read the MMP block. It _must_ be read from disk and hence we clear the
  * uptodate flag on the buffer.
@@ -290,6 +298,7 @@
 	if (mmp_block < le32_to_cpu(es->s_first_data_block) ||
 	    mmp_block >= ext4_blocks_count(es)) {
 		ext4_warning(sb, "Invalid MMP block in superblock");
+		retval = -EINVAL;
 		goto failed;
 	}
 
@@ -315,6 +324,7 @@
 
 	if (seq == EXT4_MMP_SEQ_FSCK) {
 		dump_mmp_msg(sb, mmp, "fsck is running on the filesystem");
+		retval = -EBUSY;
 		goto failed;
 	}
 
@@ -328,6 +338,7 @@
 
 	if (schedule_timeout_interruptible(HZ * wait_time) != 0) {
 		ext4_warning(sb, "MMP startup interrupted, failing mount\n");
+		retval = -ETIMEDOUT;
 		goto failed;
 	}
 
@@ -338,6 +349,7 @@
 	if (seq != le32_to_cpu(mmp->mmp_seq)) {
 		dump_mmp_msg(sb, mmp,
 			     "Device is already active on another node.");
+		retval = -EBUSY;
 		goto failed;
 	}
 
@@ -348,7 +360,11 @@
 	seq = mmp_new_seq();
 	mmp->mmp_seq = cpu_to_le32(seq);
 
-	retval = write_mmp_block(sb, bh);
+	/*
+	 * On mount / remount we are protected against fs freezing (by s_umount
+	 * semaphore) and grabbing freeze protection upsets lockdep
+	 */
+	retval = write_mmp_block_thawed(sb, bh);
 	if (retval)
 		goto failed;
 
@@ -357,6 +373,7 @@
 	 */
 	if (schedule_timeout_interruptible(HZ * wait_time) != 0) {
 		ext4_warning(sb, "MMP startup interrupted, failing mount");
+		retval = -ETIMEDOUT;
 		goto failed;
 	}
 
@@ -367,6 +384,7 @@
 	if (seq != le32_to_cpu(mmp->mmp_seq)) {
 		dump_mmp_msg(sb, mmp,
 			     "Device is already active on another node.");
+		retval = -EBUSY;
 		goto failed;
 	}
 
@@ -383,6 +401,7 @@
 		EXT4_SB(sb)->s_mmp_tsk = NULL;
 		ext4_warning(sb, "Unable to create kmmpd thread for %s.",
 			     sb->s_id);
+		retval = -ENOMEM;
 		goto failed;
 	}
 
@@ -390,5 +409,5 @@
 
 failed:
 	brelse(bh);
-	return 1;
+	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/move_extent.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/move_extent.c
@@ -36,7 +36,6 @@
 		*ppath = NULL;
 		return -ENODATA;
 	}
-	*ppath = path;
 	return 0;
 }
 
@@ -615,6 +614,7 @@
 		goto out;
 	o_end = o_start + len;
 
+	*moved_len = 0;
 	while (o_start < o_end) {
 		struct ext4_extent *ex;
 		ext4_lblk_t cur_blk, next_blk;
@@ -670,7 +670,7 @@
 		 */
 		ext4_double_up_write_data_sem(orig_inode, donor_inode);
 		/* Swap original branches with new branches */
-		move_extent_per_page(o_filp, donor_inode,
+		*moved_len += move_extent_per_page(o_filp, donor_inode,
 				     orig_page_index, donor_page_index,
 				     offset_in_page, cur_len,
 				     unwritten, &ret);
@@ -680,9 +680,6 @@
 		o_start += cur_len;
 		d_start += cur_len;
 	}
-	*moved_len = o_start - orig_blk;
-	if (*moved_len > len)
-		*moved_len = len;
 
 out:
 	if (*moved_len) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/namei.c
@@ -54,6 +54,7 @@
 					struct inode *inode,
 					ext4_lblk_t *block)
 {
+	struct ext4_map_blocks map;
 	struct buffer_head *bh;
 	int err;
 
@@ -63,21 +64,41 @@
 		return ERR_PTR(-ENOSPC);
 
 	*block = inode->i_size >> inode->i_sb->s_blocksize_bits;
+	map.m_lblk = *block;
+	map.m_len = 1;
+
+	/*
+	 * We're appending new directory block. Make sure the block is not
+	 * allocated yet, otherwise we will end up corrupting the
+	 * directory.
+	 */
+	err = ext4_map_blocks(NULL, inode, &map, 0);
+	if (err < 0)
+		return ERR_PTR(err);
+	if (err) {
+		EXT4_ERROR_INODE(inode, "Logical block already allocated");
+		return ERR_PTR(-EFSCORRUPTED);
+	}
 
 	bh = ext4_bread(handle, inode, *block, EXT4_GET_BLOCKS_CREATE);
 	if (IS_ERR(bh))
 		return bh;
 	inode->i_size += inode->i_sb->s_blocksize;
 	EXT4_I(inode)->i_disksize = inode->i_size;
+	err = ext4_mark_inode_dirty(handle, inode);
+	if (err)
+		goto out;
 	BUFFER_TRACE(bh, "get_write_access");
 	err = ext4_journal_get_write_access(handle, inode->i_sb, bh,
 					    EXT4_JTR_NONE);
-	if (err) {
-		brelse(bh);
-		ext4_std_error(inode->i_sb, err);
-		return ERR_PTR(err);
-	}
+	if (err)
+		goto out;
 	return bh;
+
+out:
+	brelse(bh);
+	ext4_std_error(inode->i_sb, err);
+	return ERR_PTR(err);
 }
 
 static int ext4_dx_csum_verify(struct inode *inode,
@@ -110,6 +131,13 @@
 	struct ext4_dir_entry *dirent;
 	int is_dx_block = 0;
 
+	if (block >= inode->i_size >> inode->i_blkbits) {
+		ext4_error_inode(inode, func, line, block,
+		       "Attempting to read directory block (%u) that is past i_size (%llu)",
+		       block, inode->i_size);
+		return ERR_PTR(-EFSCORRUPTED);
+	}
+
 	if (ext4_simulate_fail(inode->i_sb, EXT4_SIM_DIRBLOCK_EIO))
 		bh = ERR_PTR(-EIO);
 	else
@@ -123,10 +151,11 @@
 
 		return bh;
 	}
-	if (!bh && (type == INDEX || type == DIRENT_HTREE)) {
+	/* The first directory block must not be a hole. */
+	if (!bh && (type == INDEX || type == DIRENT_HTREE || block == 0)) {
 		ext4_error_inode(inode, func, line, block,
-				 "Directory hole found for htree %s block",
-				 (type == INDEX) ? "index" : "leaf");
+				 "Directory hole found for htree %s block %u",
+				 (type == INDEX) ? "index" : "leaf", block);
 		return ERR_PTR(-EFSCORRUPTED);
 	}
 	if (!bh)
@@ -277,9 +306,9 @@
 				 struct dx_hash_info *hinfo,
 				 struct dx_frame *frame);
 static void dx_release(struct dx_frame *frames);
-static int dx_make_map(struct inode *dir, struct ext4_dir_entry_2 *de,
-		       unsigned blocksize, struct dx_hash_info *hinfo,
-		       struct dx_map_entry map[]);
+static int dx_make_map(struct inode *dir, struct buffer_head *bh,
+		       struct dx_hash_info *hinfo,
+		       struct dx_map_entry *map_tail);
 static void dx_sort_map(struct dx_map_entry *map, unsigned count);
 static struct ext4_dir_entry_2 *dx_move_dirents(struct inode *dir, char *from,
 					char *to, struct dx_map_entry *offsets,
@@ -315,17 +344,17 @@
 						   struct buffer_head *bh)
 {
 	struct ext4_dir_entry_tail *t;
+	int blocksize = EXT4_BLOCK_SIZE(inode->i_sb);
 
 #ifdef PARANOID
 	struct ext4_dir_entry *d, *top;
 
 	d = (struct ext4_dir_entry *)bh->b_data;
 	top = (struct ext4_dir_entry *)(bh->b_data +
-		(EXT4_BLOCK_SIZE(inode->i_sb) -
-		 sizeof(struct ext4_dir_entry_tail)));
-	while (d < top && d->rec_len)
+		(blocksize - sizeof(struct ext4_dir_entry_tail)));
+	while (d < top && ext4_rec_len_from_disk(d->rec_len, blocksize))
 		d = (struct ext4_dir_entry *)(((void *)d) +
-		    le16_to_cpu(d->rec_len));
+		    ext4_rec_len_from_disk(d->rec_len, blocksize));
 
 	if (d != top)
 		return NULL;
@@ -336,7 +365,8 @@
 #endif
 
 	if (t->det_reserved_zero1 ||
-	    le16_to_cpu(t->det_rec_len) != sizeof(struct ext4_dir_entry_tail) ||
+	    (ext4_rec_len_from_disk(t->det_rec_len, blocksize) !=
+	     sizeof(struct ext4_dir_entry_tail)) ||
 	    t->det_reserved_zero2 ||
 	    t->det_reserved_ft != EXT4_FT_DIR_CSUM)
 		return NULL;
@@ -417,13 +447,14 @@
 	struct ext4_dir_entry *dp;
 	struct dx_root_info *root;
 	int count_offset;
+	int blocksize = EXT4_BLOCK_SIZE(inode->i_sb);
+	unsigned int rlen = ext4_rec_len_from_disk(dirent->rec_len, blocksize);
 
-	if (le16_to_cpu(dirent->rec_len) == EXT4_BLOCK_SIZE(inode->i_sb))
+	if (rlen == blocksize)
 		count_offset = 8;
-	else if (le16_to_cpu(dirent->rec_len) == 12) {
+	else if (rlen == 12) {
 		dp = (struct ext4_dir_entry *)(((void *)dirent) + 12);
-		if (le16_to_cpu(dp->rec_len) !=
-		    EXT4_BLOCK_SIZE(inode->i_sb) - 12)
+		if (ext4_rec_len_from_disk(dp->rec_len, blocksize) != blocksize - 12)
 			return NULL;
 		root = (struct dx_root_info *)(((void *)dp + 12));
 		if (root->reserved_zero ||
@@ -646,7 +677,7 @@
 				len = de->name_len;
 				if (!IS_ENCRYPTED(dir)) {
 					/* Directory is not encrypted */
-					ext4fs_dirhash(dir, de->name,
+					(void) ext4fs_dirhash(dir, de->name,
 						de->name_len, &h);
 					printk("%*.s:(U)%x.%u ", len,
 					       name, h.hash,
@@ -681,8 +712,9 @@
 					if (IS_CASEFOLDED(dir))
 						h.hash = EXT4_DIRENT_HASH(de);
 					else
-						ext4fs_dirhash(dir, de->name,
-						       de->name_len, &h);
+						(void) ext4fs_dirhash(dir,
+							de->name,
+							de->name_len, &h);
 					printk("%*.s:(E)%x.%u ", len, name,
 					       h.hash, (unsigned) ((char *) de
 								   - base));
@@ -692,7 +724,8 @@
 #else
 				int len = de->name_len;
 				char *name = de->name;
-				ext4fs_dirhash(dir, de->name, de->name_len, &h);
+				(void) ext4fs_dirhash(dir, de->name,
+						      de->name_len, &h);
 				printk("%*.s:%x.%u ", len, name, h.hash,
 				       (unsigned) ((char *) de - base));
 #endif
@@ -777,12 +810,14 @@
 dx_probe(struct ext4_filename *fname, struct inode *dir,
 	 struct dx_hash_info *hinfo, struct dx_frame *frame_in)
 {
-	unsigned count, indirect;
+	unsigned count, indirect, level, i;
 	struct dx_entry *at, *entries, *p, *q, *m;
 	struct dx_root *root;
 	struct dx_frame *frame = frame_in;
 	struct dx_frame *ret_err = ERR_PTR(ERR_BAD_DX_DIR);
 	u32 hash;
+	ext4_lblk_t block;
+	ext4_lblk_t blocks[EXT4_HTREE_LEVEL];
 
 	memset(frame_in, 0, EXT4_HTREE_LEVEL * sizeof(frame_in[0]));
 	frame->bh = ext4_read_dirblock(dir, 0, INDEX);
@@ -819,8 +854,14 @@
 	hinfo->seed = EXT4_SB(dir->i_sb)->s_hash_seed;
 	/* hash is already computed for encrypted casefolded directory */
 	if (fname && fname_name(fname) &&
-				!(IS_ENCRYPTED(dir) && IS_CASEFOLDED(dir)))
-		ext4fs_dirhash(dir, fname_name(fname), fname_len(fname), hinfo);
+	    !(IS_ENCRYPTED(dir) && IS_CASEFOLDED(dir))) {
+		int ret = ext4fs_dirhash(dir, fname_name(fname),
+					 fname_len(fname), hinfo);
+		if (ret < 0) {
+			ret_err = ERR_PTR(ret);
+			goto fail;
+		}
+	}
 	hash = hinfo->hash;
 
 	if (root->info.unused_flags & 1) {
@@ -854,6 +895,8 @@
 	}
 
 	dxtrace(printk("Look up %x", hash));
+	level = 0;
+	blocks[0] = 0;
 	while (1) {
 		count = dx_get_count(entries);
 		if (!count || count > dx_get_limit(entries)) {
@@ -882,15 +925,27 @@
 			       dx_get_block(at)));
 		frame->entries = entries;
 		frame->at = at;
-		if (!indirect--)
+
+		block = dx_get_block(at);
+		for (i = 0; i <= level; i++) {
+			if (blocks[i] == block) {
+				ext4_warning_inode(dir,
+					"dx entry: tree cycle block %u points back to block %u",
+					blocks[level], block);
+				goto fail;
+			}
+		}
+		if (++level > indirect)
 			return frame;
+		blocks[level] = block;
 		frame++;
-		frame->bh = ext4_read_dirblock(dir, dx_get_block(at), INDEX);
+		frame->bh = ext4_read_dirblock(dir, block, INDEX);
 		if (IS_ERR(frame->bh)) {
 			ret_err = (struct dx_frame *) frame->bh;
 			frame->bh = NULL;
 			goto fail;
 		}
+
 		entries = ((struct dx_node *) frame->bh->b_data)->entries;
 
 		if (dx_get_limit(entries) != dx_node_limit(dir)) {
@@ -1067,7 +1122,12 @@
 				hinfo->minor_hash = 0;
 			}
 		} else {
-			ext4fs_dirhash(dir, de->name, de->name_len, hinfo);
+			err = ext4fs_dirhash(dir, de->name,
+					     de->name_len, hinfo);
+			if (err < 0) {
+				count = err;
+				goto errout;
+			}
 		}
 		if ((hinfo->hash < start_hash) ||
 		    ((hinfo->hash == start_hash) &&
@@ -1249,28 +1309,41 @@
  * Create map of hash values, offsets, and sizes, stored at end of block.
  * Returns number of entries mapped.
  */
-static int dx_make_map(struct inode *dir, struct ext4_dir_entry_2 *de,
-		       unsigned blocksize, struct dx_hash_info *hinfo,
+static int dx_make_map(struct inode *dir, struct buffer_head *bh,
+		       struct dx_hash_info *hinfo,
 		       struct dx_map_entry *map_tail)
 {
 	int count = 0;
-	char *base = (char *) de;
+	struct ext4_dir_entry_2 *de = (struct ext4_dir_entry_2 *)bh->b_data;
+	unsigned int buflen = bh->b_size;
+	char *base = bh->b_data;
 	struct dx_hash_info h = *hinfo;
+	int blocksize = EXT4_BLOCK_SIZE(dir->i_sb);
 
-	while ((char *) de < base + blocksize) {
+	if (ext4_has_metadata_csum(dir->i_sb))
+		buflen -= sizeof(struct ext4_dir_entry_tail);
+
+	while ((char *) de < base + buflen) {
+		if (ext4_check_dir_entry(dir, NULL, de, bh, base, buflen,
+					 ((char *)de) - base))
+			return -EFSCORRUPTED;
 		if (de->name_len && de->inode) {
 			if (ext4_hash_in_dirent(dir))
 				h.hash = EXT4_DIRENT_HASH(de);
-			else
-				ext4fs_dirhash(dir, de->name, de->name_len, &h);
+			else {
+				int err = ext4fs_dirhash(dir, de->name,
+						     de->name_len, &h);
+				if (err < 0)
+					return err;
+			}
 			map_tail--;
 			map_tail->hash = h.hash;
 			map_tail->offs = ((char *) de - base)>>2;
-			map_tail->size = le16_to_cpu(de->rec_len);
+			map_tail->size = ext4_rec_len_from_disk(de->rec_len,
+								blocksize);
 			count++;
 			cond_resched();
 		}
-		/* XXX: do we need to check rec_len == 0 case? -Chris */
 		de = ext4_next_entry(de, blocksize);
 	}
 	return count;
@@ -1401,10 +1474,9 @@
 	hinfo->hash_version = DX_HASH_SIPHASH;
 	hinfo->seed = NULL;
 	if (cf_name->name)
-		ext4fs_dirhash(dir, cf_name->name, cf_name->len, hinfo);
+		return ext4fs_dirhash(dir, cf_name->name, cf_name->len, hinfo);
 	else
-		ext4fs_dirhash(dir, iname->name, iname->len, hinfo);
-	return 0;
+		return ext4fs_dirhash(dir, iname->name, iname->len, hinfo);
 }
 #endif
 
@@ -1454,7 +1526,7 @@
 }
 
 /*
- * Returns 0 if not found, -1 on failure, and 1 on success
+ * Returns 0 if not found, -EFSCORRUPTED on failure, and 1 on success
  */
 int ext4_search_dir(struct buffer_head *bh, char *search_buf, int buf_size,
 		    struct inode *dir, struct ext4_filename *fname,
@@ -1466,16 +1538,16 @@
 
 	de = (struct ext4_dir_entry_2 *)search_buf;
 	dlimit = search_buf + buf_size;
-	while ((char *) de < dlimit) {
+	while ((char *) de < dlimit - EXT4_BASE_DIR_LEN) {
 		/* this code is executed quadratically often */
 		/* do minimal checking `by hand' */
-		if ((char *) de + de->name_len <= dlimit &&
+		if (de->name + de->name_len <= dlimit &&
 		    ext4_match(dir, fname, de)) {
 			/* found a match - just to be sure, do
 			 * a full check */
 			if (ext4_check_dir_entry(dir, NULL, de, bh, search_buf,
 						 buf_size, offset))
-				return -1;
+				return -EFSCORRUPTED;
 			*res_dir = de;
 			return 1;
 		}
@@ -1483,7 +1555,7 @@
 		de_len = ext4_rec_len_from_disk(de->rec_len,
 						dir->i_sb->s_blocksize);
 		if (de_len <= 0)
-			return -1;
+			return -EFSCORRUPTED;
 		offset += de_len;
 		de = (struct ext4_dir_entry_2 *) ((char *) de + de_len);
 	}
@@ -1544,11 +1616,10 @@
 		int has_inline_data = 1;
 		ret = ext4_find_inline_entry(dir, fname, res_dir,
 					     &has_inline_data);
-		if (has_inline_data) {
-			if (inlined)
-				*inlined = 1;
+		if (inlined)
+			*inlined = has_inline_data;
+		if (has_inline_data)
 			goto cleanup_and_exit;
-		}
 	}
 
 	if ((namelen <= 2) && (name[0] == '.') &&
@@ -1636,8 +1707,10 @@
 			goto cleanup_and_exit;
 		} else {
 			brelse(bh);
-			if (i < 0)
+			if (i < 0) {
+				ret = ERR_PTR(i);
 				goto cleanup_and_exit;
+			}
 		}
 	next:
 		if (++block >= nblocks)
@@ -1732,7 +1805,7 @@
 		if (retval == 1)
 			goto success;
 		brelse(bh);
-		if (retval == -1) {
+		if (retval < 0) {
 			bh = ERR_PTR(ERR_BAD_DX_DIR);
 			goto errout;
 		}
@@ -1906,7 +1979,8 @@
 			struct dx_hash_info *hinfo)
 {
 	unsigned blocksize = dir->i_sb->s_blocksize;
-	unsigned count, continued;
+	unsigned continued;
+	int count;
 	struct buffer_head *bh2;
 	ext4_lblk_t newblock;
 	u32 hash2;
@@ -1943,8 +2017,11 @@
 
 	/* create map in the end of data2 block */
 	map = (struct dx_map_entry *) (data2 + blocksize);
-	count = dx_make_map(dir, (struct ext4_dir_entry_2 *) data1,
-			     blocksize, hinfo, map);
+	count = dx_make_map(dir, *bh, hinfo, map);
+	if (count < 0) {
+		err = count;
+		goto journal_error;
+	}
 	map -= count;
 	dx_sort_map(map, count);
 	/* Ensure that neither split block is over half full */
@@ -1970,7 +2047,7 @@
 		split = count/2;
 
 	hash2 = map[split].hash;
-	continued = hash2 == map[split - 1].hash;
+	continued = split > 0 ? hash2 == map[split - 1].hash : 0;
 	dxtrace(printk(KERN_INFO "Split block %lu at %x, %i/%i\n",
 			(unsigned long)dx_get_block(frame->at),
 					hash2, split, count-split));
@@ -2144,6 +2221,52 @@
 	return err ? err : err2;
 }
 
+static bool ext4_check_dx_root(struct inode *dir, struct dx_root *root)
+{
+	struct fake_dirent *fde;
+	const char *error_msg;
+	unsigned int rlen;
+	unsigned int blocksize = dir->i_sb->s_blocksize;
+	char *blockend = (char *)root + dir->i_sb->s_blocksize;
+
+	fde = &root->dot;
+	if (unlikely(fde->name_len != 1)) {
+		error_msg = "invalid name_len for '.'";
+		goto corrupted;
+	}
+	if (unlikely(strncmp(root->dot_name, ".", fde->name_len))) {
+		error_msg = "invalid name for '.'";
+		goto corrupted;
+	}
+	rlen = ext4_rec_len_from_disk(fde->rec_len, blocksize);
+	if (unlikely((char *)fde + rlen >= blockend)) {
+		error_msg = "invalid rec_len for '.'";
+		goto corrupted;
+	}
+
+	fde = &root->dotdot;
+	if (unlikely(fde->name_len != 2)) {
+		error_msg = "invalid name_len for '..'";
+		goto corrupted;
+	}
+	if (unlikely(strncmp(root->dotdot_name, "..", fde->name_len))) {
+		error_msg = "invalid name for '..'";
+		goto corrupted;
+	}
+	rlen = ext4_rec_len_from_disk(fde->rec_len, blocksize);
+	if (unlikely((char *)fde + rlen >= blockend)) {
+		error_msg = "invalid rec_len for '..'";
+		goto corrupted;
+	}
+
+	return true;
+
+corrupted:
+	EXT4_ERROR_INODE(dir, "Corrupt dir, %s, running e2fsck is recommended",
+			 error_msg);
+	return false;
+}
+
 /*
  * This converts a one block unindexed directory to a 3 block indexed
  * directory, and adds the dentry to the indexed directory.
@@ -2178,17 +2301,17 @@
 		brelse(bh);
 		return retval;
 	}
+
 	root = (struct dx_root *) bh->b_data;
+	if (!ext4_check_dx_root(dir, root)) {
+		brelse(bh);
+		return -EFSCORRUPTED;
+	}
 
 	/* The 0th block becomes the root, move the dirents out */
 	fde = &root->dotdot;
 	de = (struct ext4_dir_entry_2 *)((char *)fde +
 		ext4_rec_len_from_disk(fde->rec_len, blocksize));
-	if ((char *) de >= (((char *) root) + blocksize)) {
-		EXT4_ERROR_INODE(dir, "invalid rec_len for '..'");
-		brelse(bh);
-		return -EFSCORRUPTED;
-	}
 	len = ((char *) root) + (blocksize - csum_size) - (char *) de;
 
 	/* Allocate new block for the 0th block's dirents */
@@ -2204,8 +2327,16 @@
 	memset(de, 0, len); /* wipe old data */
 	de = (struct ext4_dir_entry_2 *) data2;
 	top = data2 + len;
-	while ((char *)(de2 = ext4_next_entry(de, blocksize)) < top)
+	while ((char *)(de2 = ext4_next_entry(de, blocksize)) < top) {
+		if (ext4_check_dir_entry(dir, NULL, de, bh2, data2, len,
+					 (data2 + (blocksize - csum_size) -
+					  (char *) de))) {
+			brelse(bh2);
+			brelse(bh);
+			return -EFSCORRUPTED;
+		}
 		de = de2;
+	}
 	de->rec_len = ext4_rec_len_to_disk(data2 + (blocksize - csum_size) -
 					   (char *) de, blocksize);
 
@@ -2236,10 +2367,15 @@
 	fname->hinfo.seed = EXT4_SB(dir->i_sb)->s_hash_seed;
 
 	/* casefolded encrypted hashes are computed on fname setup */
-	if (!ext4_hash_in_dirent(dir))
-		ext4fs_dirhash(dir, fname_name(fname),
-				fname_len(fname), &fname->hinfo);
-
+	if (!ext4_hash_in_dirent(dir)) {
+		int err = ext4fs_dirhash(dir, fname_name(fname),
+					 fname_len(fname), &fname->hinfo);
+		if (err < 0) {
+			brelse(bh2);
+			brelse(bh);
+			return err;
+		}
+	}
 	memset(frames, 0, sizeof(frames));
 	frame = frames;
 	frame->entries = entries;
@@ -2716,6 +2852,7 @@
 		return err;
 	}
 	drop_nlink(inode);
+	ext4_mark_inode_dirty(handle, inode);
 	ext4_orphan_add(handle, inode);
 	unlock_new_inode(inode);
 	return err;
@@ -2813,7 +2950,7 @@
 	inode = ext4_new_inode_start_handle(mnt_userns, dir, mode,
 					    NULL, 0, NULL,
 					    EXT4_HT_DIR,
-			EXT4_MAXQUOTAS_INIT_BLOCKS(dir->i_sb) +
+			EXT4_MAXQUOTAS_TRANS_BLOCKS(dir->i_sb) +
 			  4 + EXT4_XATTR_TRANS_BLOCKS);
 	handle = ext4_journal_current_handle();
 	err = PTR_ERR(inode);
@@ -2997,14 +3134,11 @@
 	if (inode->i_size < ext4_dir_rec_len(1, NULL) +
 					ext4_dir_rec_len(2, NULL)) {
 		EXT4_ERROR_INODE(inode, "invalid size");
-		return true;
+		return false;
 	}
-	/* The first directory block must not be a hole,
-	 * so treat it as DIRENT_HTREE
-	 */
-	bh = ext4_read_dirblock(inode, 0, DIRENT_HTREE);
+	bh = ext4_read_dirblock(inode, 0, EITHER);
 	if (IS_ERR(bh))
-		return true;
+		return false;
 
 	de = (struct ext4_dir_entry_2 *) bh->b_data;
 	if (ext4_check_dir_entry(inode, NULL, de, bh, bh->b_data, bh->b_size,
@@ -3012,7 +3146,7 @@
 	    le32_to_cpu(de->inode) != inode->i_ino || strcmp(".", de->name)) {
 		ext4_warning_inode(inode, "directory missing '.'");
 		brelse(bh);
-		return true;
+		return false;
 	}
 	offset = ext4_rec_len_from_disk(de->rec_len, sb->s_blocksize);
 	de = ext4_next_entry(de, sb->s_blocksize);
@@ -3021,7 +3155,7 @@
 	    le32_to_cpu(de->inode) == 0 || strcmp("..", de->name)) {
 		ext4_warning_inode(inode, "directory missing '..'");
 		brelse(bh);
-		return true;
+		return false;
 	}
 	offset += ext4_rec_len_from_disk(de->rec_len, sb->s_blocksize);
 	while (offset < inode->i_size) {
@@ -3035,16 +3169,13 @@
 				continue;
 			}
 			if (IS_ERR(bh))
-				return true;
+				return false;
 		}
 		de = (struct ext4_dir_entry_2 *) (bh->b_data +
 					(offset & (sb->s_blocksize - 1)));
 		if (ext4_check_dir_entry(inode, NULL, de, bh,
-					 bh->b_data, bh->b_size, offset)) {
-			offset = (offset | (sb->s_blocksize - 1)) + 1;
-			continue;
-		}
-		if (le32_to_cpu(de->inode)) {
+					 bh->b_data, bh->b_size, offset) ||
+		    le32_to_cpu(de->inode)) {
 			brelse(bh);
 			return false;
 		}
@@ -3144,14 +3275,20 @@
 	return retval;
 }
 
-int __ext4_unlink(handle_t *handle, struct inode *dir, const struct qstr *d_name,
-		  struct inode *inode)
+int __ext4_unlink(struct inode *dir, const struct qstr *d_name,
+		  struct inode *inode,
+		  struct dentry *dentry /* NULL during fast_commit recovery */)
 {
 	int retval = -ENOENT;
 	struct buffer_head *bh;
 	struct ext4_dir_entry_2 *de;
+	handle_t *handle;
 	int skip_remove_dentry = 0;
 
+	/*
+	 * Keep this outside the transaction; it may have to set up the
+	 * directory's encryption key, which isn't GFP_NOFS-safe.
+	 */
 	bh = ext4_find_entry(dir, d_name, &de, NULL);
 	if (IS_ERR(bh))
 		return PTR_ERR(bh);
@@ -3168,7 +3305,14 @@
 		if (EXT4_SB(inode->i_sb)->s_mount_state & EXT4_FC_REPLAY)
 			skip_remove_dentry = 1;
 		else
-			goto out;
+			goto out_bh;
+	}
+
+	handle = ext4_journal_start(dir, EXT4_HT_DIR,
+				    EXT4_DATA_TRANS_BLOCKS(dir->i_sb));
+	if (IS_ERR(handle)) {
+		retval = PTR_ERR(handle);
+		goto out_bh;
 	}
 
 	if (IS_DIRSYNC(dir))
@@ -3177,12 +3321,12 @@
 	if (!skip_remove_dentry) {
 		retval = ext4_delete_entry(handle, dir, de, bh);
 		if (retval)
-			goto out;
+			goto out_handle;
 		dir->i_ctime = dir->i_mtime = current_time(dir);
 		ext4_update_dx_flag(dir);
 		retval = ext4_mark_inode_dirty(handle, dir);
 		if (retval)
-			goto out;
+			goto out_handle;
 	} else {
 		retval = 0;
 	}
@@ -3195,15 +3339,17 @@
 		ext4_orphan_add(handle, inode);
 	inode->i_ctime = current_time(inode);
 	retval = ext4_mark_inode_dirty(handle, inode);
-
-out:
+	if (dentry && !retval)
+		ext4_fc_track_unlink(handle, dentry);
+out_handle:
+	ext4_journal_stop(handle);
+out_bh:
 	brelse(bh);
 	return retval;
 }
 
 static int ext4_unlink(struct inode *dir, struct dentry *dentry)
 {
-	handle_t *handle;
 	int retval;
 
 	if (unlikely(ext4_forced_shutdown(EXT4_SB(dir->i_sb))))
@@ -3221,16 +3367,7 @@
 	if (retval)
 		goto out_trace;
 
-	handle = ext4_journal_start(dir, EXT4_HT_DIR,
-				    EXT4_DATA_TRANS_BLOCKS(dir->i_sb));
-	if (IS_ERR(handle)) {
-		retval = PTR_ERR(handle);
-		goto out_trace;
-	}
-
-	retval = __ext4_unlink(handle, dir, &dentry->d_name, d_inode(dentry));
-	if (!retval)
-		ext4_fc_track_unlink(handle, dentry);
+	retval = __ext4_unlink(dir, &dentry->d_name, d_inode(dentry), dentry);
 #ifdef CONFIG_UNICODE
 	/* VFS negative dentries are incompatible with Encoding and
 	 * Case-insensitiveness. Eventually we'll want avoid
@@ -3241,8 +3378,6 @@
 	if (IS_CASEFOLDED(dir))
 		d_invalidate(dentry);
 #endif
-	if (handle)
-		ext4_journal_stop(handle);
 
 out_trace:
 	trace_ext4_unlink_exit(dentry, retval);
@@ -3371,6 +3506,7 @@
 	if (handle)
 		ext4_journal_stop(handle);
 	clear_nlink(inode);
+	ext4_mark_inode_dirty(handle, inode);
 	unlock_new_inode(inode);
 	iput(inode);
 out_free_encrypted_link:
@@ -3455,17 +3591,38 @@
 	struct buffer_head *bh;
 
 	if (!ext4_has_inline_data(inode)) {
-		/* The first directory block must not be a hole, so
-		 * treat it as DIRENT_HTREE
-		 */
-		bh = ext4_read_dirblock(inode, 0, DIRENT_HTREE);
+		struct ext4_dir_entry_2 *de;
+		unsigned int offset;
+
+		bh = ext4_read_dirblock(inode, 0, EITHER);
 		if (IS_ERR(bh)) {
 			*retval = PTR_ERR(bh);
 			return NULL;
 		}
-		*parent_de = ext4_next_entry(
-					(struct ext4_dir_entry_2 *)bh->b_data,
-					inode->i_sb->s_blocksize);
+
+		de = (struct ext4_dir_entry_2 *) bh->b_data;
+		if (ext4_check_dir_entry(inode, NULL, de, bh, bh->b_data,
+					 bh->b_size, 0) ||
+		    le32_to_cpu(de->inode) != inode->i_ino ||
+		    strcmp(".", de->name)) {
+			EXT4_ERROR_INODE(inode, "directory missing '.'");
+			brelse(bh);
+			*retval = -EFSCORRUPTED;
+			return NULL;
+		}
+		offset = ext4_rec_len_from_disk(de->rec_len,
+						inode->i_sb->s_blocksize);
+		de = ext4_next_entry(de, inode->i_sb->s_blocksize);
+		if (ext4_check_dir_entry(inode, NULL, de, bh, bh->b_data,
+					 bh->b_size, offset) ||
+		    le32_to_cpu(de->inode) == 0 || strcmp("..", de->name)) {
+			EXT4_ERROR_INODE(inode, "directory missing '..'");
+			brelse(bh);
+			*retval = -EFSCORRUPTED;
+			return NULL;
+		}
+		*parent_de = de;
+
 		return bh;
 	}
 
@@ -3572,7 +3729,8 @@
 	 * so the old->de may no longer valid and need to find it again
 	 * before reset old inode info.
 	 */
-	old.bh = ext4_find_entry(old.dir, &old.dentry->d_name, &old.de, NULL);
+	old.bh = ext4_find_entry(old.dir, &old.dentry->d_name, &old.de,
+				 &old.inlined);
 	if (IS_ERR(old.bh))
 		retval = PTR_ERR(old.bh);
 	if (!old.bh)
@@ -3724,6 +3882,9 @@
 	retval = dquot_initialize(old.dir);
 	if (retval)
 		return retval;
+	retval = dquot_initialize(old.inode);
+	if (retval)
+		return retval;
 	retval = dquot_initialize(new.dir);
 	if (retval)
 		return retval;
@@ -3736,9 +3897,11 @@
 			return retval;
 	}
 
-	old.bh = ext4_find_entry(old.dir, &old.dentry->d_name, &old.de, NULL);
+	old.bh = ext4_find_entry(old.dir, &old.dentry->d_name, &old.de,
+				 &old.inlined);
 	if (IS_ERR(old.bh))
 		return PTR_ERR(old.bh);
+
 	/*
 	 *  Check for inode number is _not_ due to possible IO errors.
 	 *  We might rmdir the source, keep it as pwd of some process
@@ -3889,14 +4052,21 @@
 		 * dirents in directories.
 		 */
 		ext4_fc_mark_ineligible(old.inode->i_sb,
-			EXT4_FC_REASON_RENAME_DIR);
+			EXT4_FC_REASON_RENAME_DIR, handle);
 	} else {
+		struct super_block *sb = old.inode->i_sb;
+
 		if (new.inode)
 			ext4_fc_track_unlink(handle, new.dentry);
-		__ext4_fc_track_link(handle, old.inode, new.dentry);
-		__ext4_fc_track_unlink(handle, old.inode, old.dentry);
-		if (whiteout)
-			__ext4_fc_track_create(handle, whiteout, old.dentry);
+		if (test_opt2(sb, JOURNAL_FAST_COMMIT) &&
+		    !(EXT4_SB(sb)->s_mount_state & EXT4_FC_REPLAY) &&
+		    !(ext4_test_mount_flag(sb, EXT4_MF_FC_INELIGIBLE))) {
+			__ext4_fc_track_link(handle, old.inode, new.dentry);
+			__ext4_fc_track_unlink(handle, old.inode, old.dentry);
+			if (whiteout)
+				__ext4_fc_track_create(handle, whiteout,
+						       old.dentry);
+		}
 	}
 
 	if (new.inode) {
@@ -3914,6 +4084,7 @@
 			ext4_resetent(handle, &old,
 				      old.inode->i_ino, old_file_type);
 			drop_nlink(whiteout);
+			ext4_mark_inode_dirty(handle, whiteout);
 			ext4_orphan_add(handle, whiteout);
 		}
 		unlock_new_inode(whiteout);
@@ -3926,6 +4097,7 @@
 	brelse(old.dir_bh);
 	brelse(old.bh);
 	brelse(new.bh);
+
 	return retval;
 }
 
@@ -4049,7 +4221,7 @@
 	if (unlikely(retval))
 		goto end_rename;
 	ext4_fc_mark_ineligible(new.inode->i_sb,
-				EXT4_FC_REASON_CROSS_RENAME);
+				EXT4_FC_REASON_CROSS_RENAME, handle);
 	if (old.dir_bh) {
 		retval = ext4_rename_dir_finish(handle, &old, new.dir->i_ino);
 		if (retval)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/orphan.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/orphan.c
@@ -181,8 +181,8 @@
 	} else
 		brelse(iloc.bh);
 
-	jbd_debug(4, "superblock will point to %lu\n", inode->i_ino);
-	jbd_debug(4, "orphan inode %lu will point to %d\n",
+	ext4_debug("superblock will point to %lu\n", inode->i_ino);
+	ext4_debug("orphan inode %lu will point to %d\n",
 			inode->i_ino, NEXT_ORPHAN(inode));
 out:
 	ext4_std_error(sb, err);
@@ -251,7 +251,7 @@
 	}
 
 	mutex_lock(&sbi->s_orphan_lock);
-	jbd_debug(4, "remove inode %lu from orphan list\n", inode->i_ino);
+	ext4_debug("remove inode %lu from orphan list\n", inode->i_ino);
 
 	prev = ei->i_orphan.prev;
 	list_del_init(&ei->i_orphan);
@@ -267,7 +267,7 @@
 
 	ino_next = NEXT_ORPHAN(inode);
 	if (prev == &sbi->s_orphan) {
-		jbd_debug(4, "superblock will point to %u\n", ino_next);
+		ext4_debug("superblock will point to %u\n", ino_next);
 		BUFFER_TRACE(sbi->s_sbh, "get_write_access");
 		err = ext4_journal_get_write_access(handle, inode->i_sb,
 						    sbi->s_sbh, EXT4_JTR_NONE);
@@ -286,7 +286,7 @@
 		struct inode *i_prev =
 			&list_entry(prev, struct ext4_inode_info, i_orphan)->vfs_inode;
 
-		jbd_debug(4, "orphan inode %lu will point to %u\n",
+		ext4_debug("orphan inode %lu will point to %u\n",
 			  i_prev->i_ino, ino_next);
 		err = ext4_reserve_inode_write(handle, i_prev, &iloc2);
 		if (err) {
@@ -332,8 +332,8 @@
 			ext4_msg(sb, KERN_DEBUG,
 				"%s: truncating inode %lu to %lld bytes",
 				__func__, inode->i_ino, inode->i_size);
-		jbd_debug(2, "truncating inode %lu to %lld bytes\n",
-			  inode->i_ino, inode->i_size);
+		ext4_debug("truncating inode %lu to %lld bytes\n",
+			   inode->i_ino, inode->i_size);
 		inode_lock(inode);
 		truncate_inode_pages(inode->i_mapping, inode->i_size);
 		ret = ext4_truncate(inode);
@@ -353,8 +353,8 @@
 			ext4_msg(sb, KERN_DEBUG,
 				"%s: deleting unreferenced inode %lu",
 				__func__, inode->i_ino);
-		jbd_debug(2, "deleting unreferenced inode %lu\n",
-			  inode->i_ino);
+		ext4_debug("deleting unreferenced inode %lu\n",
+			   inode->i_ino);
 		(*nr_orphans)++;
 	}
 	iput(inode);  /* The delete magic happens here! */
@@ -391,7 +391,7 @@
 	int inodes_per_ob = ext4_inodes_per_orphan_block(sb);
 
 	if (!es->s_last_orphan && !oi->of_blocks) {
-		jbd_debug(4, "no orphan inodes to clean up\n");
+		ext4_debug("no orphan inodes to clean up\n");
 		return;
 	}
 
@@ -412,10 +412,10 @@
 		/* don't clear list on RO mount w/ errors */
 		if (es->s_last_orphan && !(s_flags & SB_RDONLY)) {
 			ext4_msg(sb, KERN_INFO, "Errors on filesystem, "
-				  "clearing orphan list.\n");
+				  "clearing orphan list.");
 			es->s_last_orphan = 0;
 		}
-		jbd_debug(1, "Skipping orphan recovery on fs with errors.\n");
+		ext4_debug("Skipping orphan recovery on fs with errors.\n");
 		return;
 	}
 
@@ -459,7 +459,7 @@
 		 * so, skip the rest.
 		 */
 		if (EXT4_SB(sb)->s_mount_state & EXT4_ERROR_FS) {
-			jbd_debug(1, "Skipping orphan recovery on fs with errors.\n");
+			ext4_debug("Skipping orphan recovery on fs with errors.\n");
 			es->s_last_orphan = 0;
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/page-io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/page-io.c
@@ -134,8 +134,10 @@
 				continue;
 			}
 			clear_buffer_async_write(bh);
-			if (bio->bi_status)
+			if (bio->bi_status) {
+				set_buffer_write_io_error(bh);
 				buffer_io_error(bh);
+			}
 		} while ((bh = bh->b_this_page) != head);
 		spin_unlock_irqrestore(&head->b_uptodate_lock, flags);
 		if (!under_io) {
@@ -411,7 +413,8 @@
 
 static void io_submit_add_bh(struct ext4_io_submit *io,
 			     struct inode *inode,
-			     struct page *page,
+			     struct page *pagecache_page,
+			     struct page *bounce_page,
 			     struct buffer_head *bh)
 {
 	int ret;
@@ -425,10 +428,11 @@
 		io_submit_init_bio(io, bh);
 		io->io_bio->bi_write_hint = inode->i_write_hint;
 	}
-	ret = bio_add_page(io->io_bio, page, bh->b_size, bh_offset(bh));
+	ret = bio_add_page(io->io_bio, bounce_page ?: pagecache_page,
+			   bh->b_size, bh_offset(bh));
 	if (ret != bh->b_size)
 		goto submit_and_retry;
-	wbc_account_cgroup_owner(io->io_wbc, page, bh->b_size);
+	wbc_account_cgroup_owner(io->io_wbc, pagecache_page, bh->b_size);
 	io->io_next_block++;
 }
 
@@ -486,6 +490,13 @@
 			/* A hole? We can safely clear the dirty bit */
 			if (!buffer_mapped(bh))
 				clear_buffer_dirty(bh);
+			/*
+			 * Keeping dirty some buffer we cannot write? Make
+			 * sure to redirty the page. This happens e.g. when
+			 * doing writeout for transaction commit.
+			 */
+			if (buffer_dirty(bh) && !PageDirty(page))
+				redirty_page_for_writepage(wbc, page);
 			if (io->io_bio)
 				ext4_io_submit(io);
 			continue;
@@ -493,6 +504,7 @@
 		if (buffer_new(bh))
 			clear_buffer_new(bh);
 		set_buffer_async_write(bh);
+		clear_buffer_dirty(bh);
 		nr_to_submit++;
 	} while ((bh = bh->b_this_page) != head);
 
@@ -535,7 +547,10 @@
 			printk_ratelimited(KERN_ERR "%s: ret = %d\n", __func__, ret);
 			redirty_page_for_writepage(wbc, page);
 			do {
-				clear_buffer_async_write(bh);
+				if (buffer_async_write(bh)) {
+					clear_buffer_async_write(bh);
+					set_buffer_dirty(bh);
+				}
 				bh = bh->b_this_page;
 			} while (bh != head);
 			goto unlock;
@@ -546,10 +561,8 @@
 	do {
 		if (!buffer_async_write(bh))
 			continue;
-		io_submit_add_bh(io, inode,
-				 bounce_page ? bounce_page : page, bh);
+		io_submit_add_bh(io, inode, page, bounce_page, bh);
 		nr_submitted++;
-		clear_buffer_dirty(bh);
 	} while ((bh = bh->b_this_page) != head);
 
 unlock:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/resize.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/resize.c
@@ -53,6 +53,16 @@
 		return -EPERM;
 
 	/*
+	 * If the reserved GDT blocks is non-zero, the resize_inode feature
+	 * should always be set.
+	 */
+	if (EXT4_SB(sb)->s_es->s_reserved_gdt_blocks &&
+	    !ext4_has_feature_resize_inode(sb)) {
+		ext4_error(sb, "resize_inode disabled but reserved GDT blocks non-zero");
+		return -EFSCORRUPTED;
+	}
+
+	/*
 	 * If we are not using the primary superblock/GDT copy don't resize,
          * because the user tools have no way of handling this.  Probably a
          * bad time to do it anyways.
@@ -217,17 +227,24 @@
 						   in the flex group */
 	__u16 *bg_flags;			/* block group flags of groups
 						   in @groups */
+	ext4_group_t resize_bg;			/* number of allocated
+						   new_group_data */
 	ext4_group_t count;			/* number of groups in @groups
 						 */
 };
 
 /*
+ * Avoiding memory allocation failures due to too many groups added each time.
+ */
+#define MAX_RESIZE_BG				16384
+
+/*
  * alloc_flex_gd() allocates a ext4_new_flex_group_data with size of
  * @flexbg_size.
  *
  * Returns NULL on failure otherwise address of the allocated structure.
  */
-static struct ext4_new_flex_group_data *alloc_flex_gd(unsigned long flexbg_size)
+static struct ext4_new_flex_group_data *alloc_flex_gd(unsigned int flexbg_size)
 {
 	struct ext4_new_flex_group_data *flex_gd;
 
@@ -235,17 +252,18 @@
 	if (flex_gd == NULL)
 		goto out3;
 
-	if (flexbg_size >= UINT_MAX / sizeof(struct ext4_new_group_data))
-		goto out2;
-	flex_gd->count = flexbg_size;
+	if (unlikely(flexbg_size > MAX_RESIZE_BG))
+		flex_gd->resize_bg = MAX_RESIZE_BG;
+	else
+		flex_gd->resize_bg = flexbg_size;
 
-	flex_gd->groups = kmalloc_array(flexbg_size,
+	flex_gd->groups = kmalloc_array(flex_gd->resize_bg,
 					sizeof(struct ext4_new_group_data),
 					GFP_NOFS);
 	if (flex_gd->groups == NULL)
 		goto out2;
 
-	flex_gd->bg_flags = kmalloc_array(flexbg_size, sizeof(__u16),
+	flex_gd->bg_flags = kmalloc_array(flex_gd->resize_bg, sizeof(__u16),
 					  GFP_NOFS);
 	if (flex_gd->bg_flags == NULL)
 		goto out1;
@@ -282,7 +300,7 @@
  */
 static int ext4_alloc_group_tables(struct super_block *sb,
 				struct ext4_new_flex_group_data *flex_gd,
-				int flexbg_size)
+				unsigned int flexbg_size)
 {
 	struct ext4_new_group_data *group_data = flex_gd->groups;
 	ext4_fsblk_t start_blk;
@@ -383,12 +401,12 @@
 		group = group_data[0].group;
 
 		printk(KERN_DEBUG "EXT4-fs: adding a flex group with "
-		       "%d groups, flexbg size is %d:\n", flex_gd->count,
+		       "%u groups, flexbg size is %u:\n", flex_gd->count,
 		       flexbg_size);
 
 		for (i = 0; i < flex_gd->count; i++) {
 			ext4_debug(
-			       "adding %s group %u: %u blocks (%d free, %d mdata blocks)\n",
+			       "adding %s group %u: %u blocks (%u free, %u mdata blocks)\n",
 			       ext4_bg_has_super(sb, group + i) ? "normal" :
 			       "no-super", group + i,
 			       group_data[i].blocks_count,
@@ -546,13 +564,8 @@
 		if (meta_bg == 0 && !ext4_bg_has_super(sb, group))
 			goto handle_itb;
 
-		if (meta_bg == 1) {
-			ext4_group_t first_group;
-			first_group = ext4_meta_bg_first_group(sb, group);
-			if (first_group != group + 1 &&
-			    first_group != group + EXT4_DESC_PER_BLOCK(sb) - 1)
-				goto handle_itb;
-		}
+		if (meta_bg == 1)
+			goto handle_itb;
 
 		block = start + ext4_bg_has_super(sb, group);
 		/* Copy all of the GDT blocks into the backup in this group */
@@ -1085,6 +1098,16 @@
 	return err;
 }
 
+static inline void ext4_set_block_group_nr(struct super_block *sb, char *data,
+					   ext4_group_t group)
+{
+	struct ext4_super_block *es = (struct ext4_super_block *) data;
+
+	es->s_block_group_nr = cpu_to_le16(group);
+	if (ext4_has_metadata_csum(sb))
+		es->s_checksum = ext4_superblock_csum(sb, es);
+}
+
 /*
  * Update the backup copies of the ext4 metadata.  These don't need to be part
  * of the main resize transaction, because e2fsck will re-write them if there
@@ -1133,6 +1156,8 @@
 	while (group < sbi->s_groups_count) {
 		struct buffer_head *bh;
 		ext4_fsblk_t backup_block;
+		int has_super = ext4_bg_has_super(sb, group);
+		ext4_fsblk_t first_block = ext4_group_first_block_no(sb, group);
 
 		/* Out of journal space, and can't get more - abort - so sad */
 		err = ext4_resize_ensure_credits_batch(handle, 1);
@@ -1142,8 +1167,7 @@
 		if (meta_bg == 0)
 			backup_block = ((ext4_fsblk_t)group) * bpg + blk_off;
 		else
-			backup_block = (ext4_group_first_block_no(sb, group) +
-					ext4_bg_has_super(sb, group));
+			backup_block = first_block + has_super;
 
 		bh = sb_getblk(sb, backup_block);
 		if (unlikely(!bh)) {
@@ -1155,12 +1179,16 @@
 			   ext4_group_first_block_no(sb, group));
 		BUFFER_TRACE(bh, "get_write_access");
 		if ((err = ext4_journal_get_write_access(handle, sb, bh,
-							 EXT4_JTR_NONE)))
+							 EXT4_JTR_NONE))) {
+			brelse(bh);
 			break;
+		}
 		lock_buffer(bh);
 		memcpy(bh->b_data, data, size);
 		if (rest)
 			memset(bh->b_data + size, 0, rest);
+		if (has_super && (backup_block == first_block))
+			ext4_set_block_group_nr(sb, bh->b_data, group);
 		set_buffer_uptodate(bh);
 		unlock_buffer(bh);
 		err = ext4_handle_dirty_metadata(handle, NULL, bh);
@@ -1435,8 +1463,6 @@
 	 * active. */
 	ext4_r_blocks_count_set(es, ext4_r_blocks_count(es) +
 				reserved_blocks);
-	ext4_superblock_csum_set(sb);
-	unlock_buffer(sbi->s_sbh);
 
 	/* Update the free space counts */
 	percpu_counter_add(&sbi->s_freeclusters_counter,
@@ -1462,7 +1488,10 @@
 	 * Update the fs overhead information
 	 */
 	ext4_calculate_overhead(sb);
+	es->s_overhead_clusters = cpu_to_le32(sbi->s_overhead);
 
+	ext4_superblock_csum_set(sb);
+	unlock_buffer(sbi->s_sbh);
 	if (test_opt(sb, DEBUG))
 		printk(KERN_DEBUG "EXT4-fs: added group %u:"
 		       "%llu blocks(%llu free %llu reserved)\n", flex_gd->count,
@@ -1543,11 +1572,14 @@
 		int gdb_num = group / EXT4_DESC_PER_BLOCK(sb);
 		int gdb_num_end = ((group + flex_gd->count - 1) /
 				   EXT4_DESC_PER_BLOCK(sb));
-		int meta_bg = ext4_has_feature_meta_bg(sb);
+		int meta_bg = ext4_has_feature_meta_bg(sb) &&
+			      gdb_num >= le32_to_cpu(es->s_first_meta_bg);
+		sector_t padding_blocks = meta_bg ? 0 : sbi->s_sbh->b_blocknr -
+					 ext4_group_first_block_no(sb, 0);
 		sector_t old_gdb = 0;
 
-		update_backups(sb, sbi->s_sbh->b_blocknr, (char *)es,
-			       sizeof(struct ext4_super_block), 0);
+		update_backups(sb, ext4_group_first_block_no(sb, 0),
+			       (char *)es, sizeof(struct ext4_super_block), 0);
 		for (; gdb_num <= gdb_num_end; gdb_num++) {
 			struct buffer_head *gdb_bh;
 
@@ -1555,8 +1587,8 @@
 						     gdb_num);
 			if (old_gdb == gdb_bh->b_blocknr)
 				continue;
-			update_backups(sb, gdb_bh->b_blocknr, gdb_bh->b_data,
-				       gdb_bh->b_size, meta_bg);
+			update_backups(sb, gdb_bh->b_blocknr - padding_blocks,
+				       gdb_bh->b_data, gdb_bh->b_size, meta_bg);
 			old_gdb = gdb_bh->b_blocknr;
 		}
 	}
@@ -1566,8 +1598,7 @@
 
 static int ext4_setup_next_flex_gd(struct super_block *sb,
 				    struct ext4_new_flex_group_data *flex_gd,
-				    ext4_fsblk_t n_blocks_count,
-				    unsigned long flexbg_size)
+				    ext4_fsblk_t n_blocks_count)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	struct ext4_super_block *es = sbi->s_es;
@@ -1591,7 +1622,7 @@
 	BUG_ON(last);
 	ext4_get_group_no_and_offset(sb, n_blocks_count - 1, &n_group, &last);
 
-	last_group = group | (flexbg_size - 1);
+	last_group = group | (flex_gd->resize_bg - 1);
 	if (last_group > n_group)
 		last_group = n_group;
 
@@ -1758,7 +1789,7 @@
 		if (test_opt(sb, DEBUG))
 			printk(KERN_DEBUG "EXT4-fs: extended group to %llu "
 			       "blocks\n", ext4_blocks_count(es));
-		update_backups(sb, EXT4_SB(sb)->s_sbh->b_blocknr,
+		update_backups(sb, ext4_group_first_block_no(sb, 0),
 			       (char *)es, sizeof(struct ext4_super_block), 0);
 	}
 	return err;
@@ -1925,9 +1956,7 @@
 
 errout:
 	ret = ext4_journal_stop(handle);
-	if (!err)
-		err = ret;
-	return ret;
+	return err ? err : ret;
 
 invalid_resize_inode:
 	ext4_error(sb, "corrupted/inconsistent resize inode");
@@ -1955,8 +1984,9 @@
 	ext4_fsblk_t o_blocks_count;
 	ext4_fsblk_t n_blocks_count_retry = 0;
 	unsigned long last_update_time = 0;
-	int err = 0, flexbg_size = 1 << sbi->s_log_groups_per_flex;
+	int err = 0;
 	int meta_bg;
+	unsigned int flexbg_size = ext4_flex_bg_size(sbi);
 
 	/* See if the device is actually as big as what was requested */
 	bh = ext4_sb_bread(sb, n_blocks_count - 1, 0);
@@ -1966,6 +1996,16 @@
 	}
 	brelse(bh);
 
+	/*
+	 * For bigalloc, trim the requested size to the nearest cluster
+	 * boundary to avoid creating an unusable filesystem. We do this
+	 * silently, instead of returning an error, to avoid breaking
+	 * callers that blindly resize the filesystem to the full size of
+	 * the underlying block device.
+	 */
+	if (ext4_has_feature_bigalloc(sb))
+		n_blocks_count &= ~((1 << EXT4_CLUSTER_BITS(sb)) - 1);
+
 retry:
 	o_blocks_count = ext4_blocks_count(es);
 
@@ -2067,7 +2107,7 @@
 			goto out;
 	}
 
-	if (ext4_blocks_count(es) == n_blocks_count)
+	if (ext4_blocks_count(es) == n_blocks_count && n_blocks_count_retry == 0)
 		goto out;
 
 	err = ext4_alloc_flex_bg_array(sb, n_group + 1);
@@ -2087,8 +2127,7 @@
 	/* Add flex groups. Note that a regular group is a
 	 * flex group with 1 group.
 	 */
-	while (ext4_setup_next_flex_gd(sb, flex_gd, n_blocks_count,
-					      flexbg_size)) {
+	while (ext4_setup_next_flex_gd(sb, flex_gd, n_blocks_count)) {
 		if (jiffies - last_update_time > HZ * 10) {
 			if (last_update_time)
 				ext4_msg(sb, KERN_INFO,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/super.c
@@ -46,6 +46,7 @@
 #include <linux/part_stat.h>
 #include <linux/kthread.h>
 #include <linux/freezer.h>
+#include <linux/fsnotify.h>
 
 #include "ext4.h"
 #include "ext4_extents.h"	/* Needed for trace points definition */
@@ -186,19 +187,12 @@
 
 int ext4_read_bh_lock(struct buffer_head *bh, int op_flags, bool wait)
 {
-	if (trylock_buffer(bh)) {
-		if (wait)
-			return ext4_read_bh(bh, op_flags, NULL);
+	lock_buffer(bh);
+	if (!wait) {
 		ext4_read_bh_nowait(bh, op_flags, NULL);
 		return 0;
 	}
-	if (wait) {
-		wait_on_buffer(bh);
-		if (buffer_uptodate(bh))
-			return 0;
-		return -EIO;
-	}
-	return 0;
+	return ext4_read_bh(bh, op_flags, NULL);
 }
 
 /*
@@ -245,7 +239,8 @@
 	struct buffer_head *bh = sb_getblk_gfp(sb, block, 0);
 
 	if (likely(bh)) {
-		ext4_read_bh_lock(bh, REQ_RAHEAD, false);
+		if (trylock_buffer(bh))
+			ext4_read_bh_nowait(bh, REQ_RAHEAD, NULL);
 		brelse(bh);
 	}
 }
@@ -259,7 +254,7 @@
 	return es->s_checksum_type == EXT4_CRC32C_CHKSUM;
 }
 
-static __le32 ext4_superblock_csum(struct super_block *sb,
+__le32 ext4_superblock_csum(struct super_block *sb,
 				   struct ext4_super_block *es)
 {
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
@@ -325,9 +320,9 @@
 __u32 ext4_free_inodes_count(struct super_block *sb,
 			      struct ext4_group_desc *bg)
 {
-	return le16_to_cpu(bg->bg_free_inodes_count_lo) |
+	return le16_to_cpu(READ_ONCE(bg->bg_free_inodes_count_lo)) |
 		(EXT4_DESC_SIZE(sb) >= EXT4_MIN_DESC_SIZE_64BIT ?
-		 (__u32)le16_to_cpu(bg->bg_free_inodes_count_hi) << 16 : 0);
+		 (__u32)le16_to_cpu(READ_ONCE(bg->bg_free_inodes_count_hi)) << 16 : 0);
 }
 
 __u32 ext4_used_dirs_count(struct super_block *sb,
@@ -381,9 +376,9 @@
 void ext4_free_inodes_set(struct super_block *sb,
 			  struct ext4_group_desc *bg, __u32 count)
 {
-	bg->bg_free_inodes_count_lo = cpu_to_le16((__u16)count);
+	WRITE_ONCE(bg->bg_free_inodes_count_lo, cpu_to_le16((__u16)count));
 	if (EXT4_DESC_SIZE(sb) >= EXT4_MIN_DESC_SIZE_64BIT)
-		bg->bg_free_inodes_count_hi = cpu_to_le16(count >> 16);
+		WRITE_ONCE(bg->bg_free_inodes_count_hi, cpu_to_le16(count >> 16));
 }
 
 void ext4_used_dirs_set(struct super_block *sb,
@@ -679,11 +674,12 @@
 
 	ext4_msg(sb, KERN_CRIT, "Remounting filesystem read-only");
 	/*
-	 * Make sure updated value of ->s_mount_flags will be visible before
-	 * ->s_flags update
+	 * EXT4_FLAGS_SHUTDOWN was set which stops all filesystem
+	 * modifications. We don't set SB_RDONLY because that requires
+	 * sb->s_umount semaphore and setting it without proper remount
+	 * procedure is confusing code such as freeze_super() leading to
+	 * deadlocks and other problems.
 	 */
-	smp_wmb();
-	sb->s_flags |= SB_RDONLY;
 }
 
 static void flush_stashed_error_work(struct work_struct *work)
@@ -759,6 +755,8 @@
 		       sb->s_id, function, line, current->comm, &vaf);
 		va_end(args);
 	}
+	fsnotify_sb_error(sb, NULL, error ? error : EFSCORRUPTED);
+
 	ext4_handle_error(sb, force_ro, error, 0, block, function, line);
 }
 
@@ -789,6 +787,8 @@
 			       current->comm, &vaf);
 		va_end(args);
 	}
+	fsnotify_sb_error(inode->i_sb, inode, error ? error : EFSCORRUPTED);
+
 	ext4_handle_error(inode->i_sb, false, error, inode->i_ino, block,
 			  function, line);
 }
@@ -827,6 +827,8 @@
 			       current->comm, path, &vaf);
 		va_end(args);
 	}
+	fsnotify_sb_error(inode->i_sb, inode, EFSCORRUPTED);
+
 	ext4_handle_error(inode->i_sb, false, EFSCORRUPTED, inode->i_ino, block,
 			  function, line);
 }
@@ -894,6 +896,7 @@
 		printk(KERN_CRIT "EXT4-fs error (device %s) in %s:%d: %s\n",
 		       sb->s_id, function, line, errstr);
 	}
+	fsnotify_sb_error(sb, NULL, errno ? errno : EFSCORRUPTED);
 
 	ext4_handle_error(sb, false, -errno, 0, 0, function, line);
 }
@@ -1023,6 +1026,8 @@
 	struct ext4_group_desc *gdp = ext4_get_group_desc(sb, group, NULL);
 	int ret;
 
+	if (!grp || !gdp)
+		return;
 	if (flags & EXT4_GROUP_INFO_BBITMAP_CORRUPT) {
 		ret = ext4_test_and_set_bit(EXT4_GROUP_INFO_BBITMAP_CORRUPT_BIT,
 					    &grp->bb_state);
@@ -1101,6 +1106,12 @@
 	struct block_device *bdev;
 	bdev = sbi->s_journal_bdev;
 	if (bdev) {
+		/*
+		 * Invalidate the journal device's buffers.  We don't want them
+		 * floating about in memory - the physical journal device may
+		 * hotswapped, and it breaks the `ro-after' testing code.
+		 */
+		invalidate_bdev(bdev);
 		ext4_blkdev_put(bdev);
 		sbi->s_journal_bdev = NULL;
 	}
@@ -1167,20 +1178,25 @@
 	int aborted = 0;
 	int i, err;
 
-	ext4_unregister_li_request(sb);
-	ext4_quota_off_umount(sb);
-
-	flush_work(&sbi->s_error_work);
-	destroy_workqueue(sbi->rsv_conversion_wq);
-	ext4_release_orphan_info(sb);
-
 	/*
 	 * Unregister sysfs before destroying jbd2 journal.
 	 * Since we could still access attr_journal_task attribute via sysfs
 	 * path which could have sbi->s_journal->j_task as NULL
+	 * Unregister sysfs before flush sbi->s_error_work.
+	 * Since user may read /proc/fs/ext4/xx/mb_groups during umount, If
+	 * read metadata verify failed then will queue error work.
+	 * flush_stashed_error_work will call start_this_handle may trigger
+	 * BUG_ON.
 	 */
 	ext4_unregister_sysfs(sb);
 
+	ext4_unregister_li_request(sb);
+	ext4_quota_off_umount(sb);
+
+	flush_work(&sbi->s_error_work);
+	destroy_workqueue(sbi->rsv_conversion_wq);
+	ext4_release_orphan_info(sb);
+
 	if (sbi->s_journal) {
 		aborted = is_journal_aborted(sbi->s_journal);
 		err = jbd2_journal_destroy(sbi->s_journal);
@@ -1238,13 +1254,7 @@
 	sync_blockdev(sb->s_bdev);
 	invalidate_bdev(sb->s_bdev);
 	if (sbi->s_journal_bdev && sbi->s_journal_bdev != sb->s_bdev) {
-		/*
-		 * Invalidate the journal device's buffers.  We don't want them
-		 * floating about in memory - the physical journal device may
-		 * hotswapped, and it breaks the `ro-after' testing code.
-		 */
 		sync_blockdev(sbi->s_journal_bdev);
-		invalidate_bdev(sbi->s_journal_bdev);
 		ext4_blkdev_remove(sbi);
 	}
 
@@ -1289,6 +1299,7 @@
 		return NULL;
 
 	inode_set_iversion(&ei->vfs_inode, 1);
+	ei->i_flags = 0;
 	spin_lock_init(&ei->i_raw_lock);
 	INIT_LIST_HEAD(&ei->i_prealloc_list);
 	atomic_set(&ei->i_prealloc_active, 0);
@@ -1929,6 +1940,7 @@
 	 MOPT_EXT4_ONLY | MOPT_CLEAR},
 	{Opt_warn_on_error, EXT4_MOUNT_WARN_ON_ERROR, MOPT_SET},
 	{Opt_nowarn_on_error, EXT4_MOUNT_WARN_ON_ERROR, MOPT_CLEAR},
+	{Opt_commit, 0, MOPT_NO_EXT2},
 	{Opt_nojournal_checksum, EXT4_MOUNT_JOURNAL_CHECKSUM,
 	 MOPT_EXT4_ONLY | MOPT_CLEAR},
 	{Opt_journal_checksum, EXT4_MOUNT_JOURNAL_CHECKSUM,
@@ -2053,6 +2065,12 @@
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	int err;
 
+	if (!ext4_has_feature_encrypt(sb)) {
+		ext4_msg(sb, KERN_WARNING,
+			 "test_dummy_encryption requires encrypt feature");
+		return -1;
+	}
+
 	/*
 	 * This mount option is just for testing, and it's not worthwhile to
 	 * implement the extra complexity (e.g. RCU protection) that would be
@@ -2080,11 +2098,13 @@
 		return -1;
 	}
 	ext4_msg(sb, KERN_WARNING, "Test dummy encryption mode enabled");
+	return 1;
 #else
 	ext4_msg(sb, KERN_WARNING,
-		 "Test dummy encryption mount option ignored");
+		 "test_dummy_encryption option not supported");
+	return -1;
+
 #endif
-	return 1;
 }
 
 struct ext4_parsed_options {
@@ -2827,11 +2847,9 @@
 	crc = crc16(crc, (__u8 *)gdp, offset);
 	offset += sizeof(gdp->bg_checksum); /* skip checksum */
 	/* for checksum of struct ext4_group_desc do the rest...*/
-	if (ext4_has_feature_64bit(sb) &&
-	    offset < le16_to_cpu(sbi->s_es->s_desc_size))
+	if (ext4_has_feature_64bit(sb) && offset < sbi->s_desc_size)
 		crc = crc16(crc, (__u8 *)gdp + offset,
-			    le16_to_cpu(sbi->s_es->s_desc_size) -
-				offset);
+			    sbi->s_desc_size - offset);
 
 out:
 	return cpu_to_le16(crc);
@@ -3263,9 +3281,9 @@
 	struct super_block *sb = elr->lr_super;
 	ext4_group_t ngroups = EXT4_SB(sb)->s_groups_count;
 	ext4_group_t group = elr->lr_next_group;
-	unsigned long timeout = 0;
 	unsigned int prefetch_ios = 0;
 	int ret = 0;
+	u64 start_time;
 
 	if (elr->lr_mode == EXT4_LI_MODE_PREFETCH_BBITMAP) {
 		elr->lr_next_group = ext4_mb_prefetch(sb, group,
@@ -3302,14 +3320,13 @@
 		ret = 1;
 
 	if (!ret) {
-		timeout = jiffies;
+		start_time = ktime_get_real_ns();
 		ret = ext4_init_inode_table(sb, group,
 					    elr->lr_timeout ? 0 : 1);
 		trace_ext4_lazy_itable_init(sb, group);
 		if (elr->lr_timeout == 0) {
-			timeout = (jiffies - timeout) *
-				EXT4_SB(elr->lr_super)->s_li_wait_mult;
-			elr->lr_timeout = timeout;
+			elr->lr_timeout = nsecs_to_jiffies((ktime_get_real_ns() - start_time) *
+				EXT4_SB(elr->lr_super)->s_li_wait_mult);
 		}
 		elr->lr_next_sched = jiffies + elr->lr_timeout;
 		elr->lr_next_group = group + 1;
@@ -3364,6 +3381,7 @@
 	unsigned long next_wakeup, cur;
 
 	BUG_ON(NULL == eli);
+	set_freezable();
 
 cont_thread:
 	while (true) {
@@ -3579,9 +3597,9 @@
 		goto out;
 	}
 
-	if (test_opt(sb, NO_PREFETCH_BLOCK_BITMAPS) &&
-	    (first_not_zeroed == ngroups || sb_rdonly(sb) ||
-	     !test_opt(sb, INIT_INODE_TABLE)))
+	if (sb_rdonly(sb) ||
+	    (test_opt(sb, NO_PREFETCH_BLOCK_BITMAPS) &&
+	     (first_not_zeroed == ngroups || !test_opt(sb, INIT_INODE_TABLE))))
 		goto out;
 
 	elr = ext4_li_request_new(sb, first_not_zeroed);
@@ -3698,9 +3716,11 @@
 	ext4_fsblk_t		first_block, last_block, b;
 	ext4_group_t		i, ngroups = ext4_get_groups_count(sb);
 	int			s, j, count = 0;
+	int			has_super = ext4_bg_has_super(sb, grp);
 
 	if (!ext4_has_feature_bigalloc(sb))
-		return (ext4_bg_has_super(sb, grp) + ext4_bg_num_gdb(sb, grp) +
+		return (has_super + ext4_bg_num_gdb(sb, grp) +
+			(has_super ? le16_to_cpu(sbi->s_es->s_reserved_gdt_blocks) : 0) +
 			sbi->s_itb_per_group + 2);
 
 	first_block = le32_to_cpu(sbi->s_es->s_first_data_block) +
@@ -4384,7 +4404,7 @@
 					sbi->s_inodes_per_block;
 	sbi->s_desc_per_block = blocksize / EXT4_DESC_SIZE(sb);
 	sbi->s_sbh = bh;
-	sbi->s_mount_state = le16_to_cpu(es->s_state);
+	sbi->s_mount_state = le16_to_cpu(es->s_state) & ~EXT4_FC_REPLAY;
 	sbi->s_addr_per_block_bits = ilog2(EXT4_ADDR_PER_BLOCK(sb));
 	sbi->s_desc_per_block_bits = ilog2(EXT4_DESC_PER_BLOCK(sb));
 
@@ -4614,14 +4634,13 @@
 
 	/* Initialize fast commit stuff */
 	atomic_set(&sbi->s_fc_subtid, 0);
-	atomic_set(&sbi->s_fc_ineligible_updates, 0);
 	INIT_LIST_HEAD(&sbi->s_fc_q[FC_Q_MAIN]);
 	INIT_LIST_HEAD(&sbi->s_fc_q[FC_Q_STAGING]);
 	INIT_LIST_HEAD(&sbi->s_fc_dentry_q[FC_Q_MAIN]);
 	INIT_LIST_HEAD(&sbi->s_fc_dentry_q[FC_Q_STAGING]);
 	sbi->s_fc_bytes = 0;
 	ext4_clear_mount_flag(sb, EXT4_MF_FC_INELIGIBLE);
-	ext4_clear_mount_flag(sb, EXT4_MF_FC_COMMITTING);
+	sbi->s_fc_ineligible_tid = 0;
 	spin_lock_init(&sbi->s_fc_lock);
 	memset(&sbi->s_fc_stats, 0, sizeof(sbi->s_fc_stats));
 	sbi->s_fc_replay_state.fc_regions = NULL;
@@ -4638,9 +4657,11 @@
 			  ext4_has_feature_orphan_present(sb) ||
 			  ext4_has_feature_journal_needs_recovery(sb));
 
-	if (ext4_has_feature_mmp(sb) && !sb_rdonly(sb))
-		if (ext4_multi_mount_protect(sb, le64_to_cpu(es->s_mmp_block)))
+	if (ext4_has_feature_mmp(sb) && !sb_rdonly(sb)) {
+		err = ext4_multi_mount_protect(sb, le64_to_cpu(es->s_mmp_block));
+		if (err)
 			goto failed_mount3a;
+	}
 
 	/*
 	 * The first inode we look at is the journal inode.  Don't try
@@ -4654,30 +4675,31 @@
 		   ext4_has_feature_journal_needs_recovery(sb)) {
 		ext4_msg(sb, KERN_ERR, "required journal recovery "
 		       "suppressed and not mounted read-only");
-		goto failed_mount_wq;
+		goto failed_mount3a;
 	} else {
 		/* Nojournal mode, all journal mount options are illegal */
-		if (test_opt2(sb, EXPLICIT_JOURNAL_CHECKSUM)) {
-			ext4_msg(sb, KERN_ERR, "can't mount with "
-				 "journal_checksum, fs mounted w/o journal");
-			goto failed_mount_wq;
-		}
 		if (test_opt(sb, JOURNAL_ASYNC_COMMIT)) {
 			ext4_msg(sb, KERN_ERR, "can't mount with "
 				 "journal_async_commit, fs mounted w/o journal");
-			goto failed_mount_wq;
+			goto failed_mount3a;
+		}
+
+		if (test_opt2(sb, EXPLICIT_JOURNAL_CHECKSUM)) {
+			ext4_msg(sb, KERN_ERR, "can't mount with "
+				 "journal_checksum, fs mounted w/o journal");
+			goto failed_mount3a;
 		}
 		if (sbi->s_commit_interval != JBD2_DEFAULT_MAX_COMMIT_AGE*HZ) {
 			ext4_msg(sb, KERN_ERR, "can't mount with "
 				 "commit=%lu, fs mounted w/o journal",
 				 sbi->s_commit_interval / HZ);
-			goto failed_mount_wq;
+			goto failed_mount3a;
 		}
 		if (EXT4_MOUNT_DATA_FLAGS &
 		    (sbi->s_mount_opt ^ sbi->s_def_mount_opt)) {
 			ext4_msg(sb, KERN_ERR, "can't mount with "
 				 "data=, fs mounted w/o journal");
-			goto failed_mount_wq;
+			goto failed_mount3a;
 		}
 		sbi->s_def_mount_opt &= ~EXT4_MOUNT_JOURNAL_CHECKSUM;
 		clear_opt(sb, JOURNAL_CHECKSUM);
@@ -4778,19 +4800,22 @@
 		goto failed_mount_wq;
 	}
 
-	if (DUMMY_ENCRYPTION_ENABLED(sbi) && !sb_rdonly(sb) &&
-	    !ext4_has_feature_encrypt(sb)) {
-		ext4_set_feature_encrypt(sb);
-		ext4_commit_super(sb);
-	}
-
 	/*
 	 * Get the # of file system overhead blocks from the
 	 * superblock if present.
 	 */
-	if (es->s_overhead_clusters)
-		sbi->s_overhead = le32_to_cpu(es->s_overhead_clusters);
-	else {
+	sbi->s_overhead = le32_to_cpu(es->s_overhead_clusters);
+	/* ignore the precalculated value if it is ridiculous */
+	if (sbi->s_overhead > ext4_blocks_count(es))
+		sbi->s_overhead = 0;
+	/*
+	 * If the bigalloc feature is not enabled recalculating the
+	 * overhead doesn't take long, so we might as well just redo
+	 * it to make sure we are using the correct value.
+	 */
+	if (!ext4_has_feature_bigalloc(sb))
+		sbi->s_overhead = 0;
+	if (sbi->s_overhead == 0) {
 		err = ext4_calculate_overhead(sb);
 		if (err)
 			goto failed_mount_wq;
@@ -4892,14 +4917,6 @@
 		err = percpu_counter_init(&sbi->s_freeinodes_counter, freei,
 					  GFP_KERNEL);
 	}
-	/*
-	 * Update the checksum after updating free space/inode
-	 * counters.  Otherwise the superblock can have an incorrect
-	 * checksum in the buffer cache until it is written out and
-	 * e2fsprogs programs trying to open a file system immediately
-	 * after it is mounted can fail.
-	 */
-	ext4_superblock_csum_set(sb);
 	if (!err)
 		err = percpu_counter_init(&sbi->s_dirs_counter,
 					  ext4_count_dirs(sb), GFP_KERNEL);
@@ -4957,11 +4974,19 @@
 	EXT4_SB(sb)->s_mount_state |= EXT4_ORPHAN_FS;
 	ext4_orphan_cleanup(sb, es);
 	EXT4_SB(sb)->s_mount_state &= ~EXT4_ORPHAN_FS;
+	/*
+	 * Update the checksum after updating free space/inode counters and
+	 * ext4_orphan_cleanup. Otherwise the superblock can have an incorrect
+	 * checksum in the buffer cache until it is written out and
+	 * e2fsprogs programs trying to open a file system immediately
+	 * after it is mounted can fail.
+	 */
+	ext4_superblock_csum_set(sb);
 	if (needs_recovery) {
 		ext4_msg(sb, KERN_INFO, "recovery complete");
 		err = ext4_mark_recovery_complete(sb, es);
 		if (err)
-			goto failed_mount9;
+			goto failed_mount10;
 	}
 	if (EXT4_SB(sb)->s_journal) {
 		if (test_opt(sb, DATA_FLAGS) == EXT4_MOUNT_JOURNAL_DATA)
@@ -5007,7 +5032,9 @@
 		ext4_msg(sb, KERN_ERR, "VFS: Can't find ext4 filesystem");
 	goto failed_mount;
 
-failed_mount9:
+failed_mount10:
+	ext4_quota_off_umount(sb);
+failed_mount9: __maybe_unused
 	ext4_release_orphan_info(sb);
 failed_mount8:
 	ext4_unregister_sysfs(sb);
@@ -5084,6 +5111,7 @@
 	brelse(bh);
 	ext4_blkdev_remove(sbi);
 out_fail:
+	invalidate_bdev(sb->s_bdev);
 	sb->s_fs_info = NULL;
 	kfree(sbi->s_blockgroup_lock);
 out_free_base:
@@ -5141,9 +5169,9 @@
 		return NULL;
 	}
 
-	jbd_debug(2, "Journal inode found at %p: %lld bytes\n",
+	ext4_debug("Journal inode found at %p: %lld bytes\n",
 		  journal_inode, journal_inode->i_size);
-	if (!S_ISREG(journal_inode->i_mode)) {
+	if (!S_ISREG(journal_inode->i_mode) || IS_ENCRYPTED(journal_inode)) {
 		ext4_msg(sb, KERN_ERR, "invalid journal inode");
 		iput(journal_inode);
 		return NULL;
@@ -5371,8 +5399,11 @@
 	if (!really_read_only && journal_devnum &&
 	    journal_devnum != le32_to_cpu(es->s_journal_dev)) {
 		es->s_journal_dev = cpu_to_le32(journal_devnum);
-
-		/* Make sure we flush the recovery flag to disk. */
+		ext4_commit_super(sb);
+	}
+	if (!really_read_only && journal_inum &&
+	    journal_inum != le32_to_cpu(es->s_journal_inum)) {
+		es->s_journal_inum = cpu_to_le32(journal_inum);
 		ext4_commit_super(sb);
 	}
 
@@ -5727,10 +5758,10 @@
 	struct ext4_sb_info *sbi = EXT4_SB(sb);
 	unsigned long old_sb_flags, vfs_flags;
 	struct ext4_mount_options old_opts;
-	int enable_quota = 0;
 	ext4_group_t g;
 	int err = 0;
 #ifdef CONFIG_QUOTA
+	int enable_quota = 0;
 	int i, j;
 	char *to_free[EXT4_MAXQUOTAS];
 #endif
@@ -5821,7 +5852,7 @@
 	}
 
 	if (ext4_test_mount_flag(sb, EXT4_MF_FS_ABORTED))
-		ext4_abort(sb, EXT4_ERR_ESHUTDOWN, "Abort forced by user");
+		ext4_abort(sb, ESHUTDOWN, "Abort forced by user");
 
 	sb->s_flags = (sb->s_flags & ~SB_POSIXACL) |
 		(test_opt(sb, POSIX_ACL) ? SB_POSIXACL : 0);
@@ -5922,36 +5953,27 @@
 				if (err)
 					goto restore_opts;
 			}
-			sbi->s_mount_state = le16_to_cpu(es->s_state);
+			sbi->s_mount_state = (le16_to_cpu(es->s_state) &
+					      ~EXT4_FC_REPLAY);
 
 			err = ext4_setup_super(sb, es, 0);
 			if (err)
 				goto restore_opts;
 
 			sb->s_flags &= ~SB_RDONLY;
-			if (ext4_has_feature_mmp(sb))
-				if (ext4_multi_mount_protect(sb,
-						le64_to_cpu(es->s_mmp_block))) {
-					err = -EROFS;
+			if (ext4_has_feature_mmp(sb)) {
+				err = ext4_multi_mount_protect(sb,
+						le64_to_cpu(es->s_mmp_block));
+				if (err)
 					goto restore_opts;
-				}
+			}
+#ifdef CONFIG_QUOTA
 			enable_quota = 1;
+#endif
 		}
 	}
 
 	/*
-	 * Reinitialize lazy itable initialization thread based on
-	 * current settings
-	 */
-	if (sb_rdonly(sb) || !test_opt(sb, INIT_INODE_TABLE))
-		ext4_unregister_li_request(sb);
-	else {
-		ext4_group_t first_not_zeroed;
-		first_not_zeroed = ext4_has_uninit_itable(sb);
-		ext4_register_li_request(sb, first_not_zeroed);
-	}
-
-	/*
 	 * Handle creation of system zone data early because it can fail.
 	 * Releasing of existing data is done when we are sure remount will
 	 * succeed.
@@ -5969,9 +5991,6 @@
 	}
 
 #ifdef CONFIG_QUOTA
-	/* Release old quota file names */
-	for (i = 0; i < EXT4_MAXQUOTAS; i++)
-		kfree(old_opts.s_qf_names[i]);
 	if (enable_quota) {
 		if (sb_any_quota_suspended(sb))
 			dquot_resume(sb, -1);
@@ -5981,10 +6000,25 @@
 				goto restore_opts;
 		}
 	}
+	/* Release old quota file names */
+	for (i = 0; i < EXT4_MAXQUOTAS; i++)
+		kfree(old_opts.s_qf_names[i]);
 #endif
 	if (!test_opt(sb, BLOCK_VALIDITY) && sbi->s_system_blks)
 		ext4_release_system_zone(sb);
 
+	/*
+	 * Reinitialize lazy itable initialization thread based on
+	 * current settings
+	 */
+	if (sb_rdonly(sb) || !test_opt(sb, INIT_INODE_TABLE))
+		ext4_unregister_li_request(sb);
+	else {
+		ext4_group_t first_not_zeroed;
+		first_not_zeroed = ext4_has_uninit_itable(sb);
+		ext4_register_li_request(sb, first_not_zeroed);
+	}
+
 	if (!ext4_has_feature_mmp(sb) || sb_rdonly(sb))
 		ext4_stop_mmpd(sbi);
 
@@ -6001,6 +6035,13 @@
 	return 0;
 
 restore_opts:
+	/*
+	 * If there was a failing r/w to ro transition, we may need to
+	 * re-enable quota
+	 */
+	if ((sb->s_flags & SB_RDONLY) && !(old_sb_flags & SB_RDONLY) &&
+	    sb_any_quota_suspended(sb))
+		dquot_resume(sb, -1);
 	sb->s_flags = old_sb_flags;
 	sbi->s_mount_opt = old_opts.s_mount_opt;
 	sbi->s_mount_opt2 = old_opts.s_mount_opt2;
@@ -6046,22 +6087,29 @@
 			     dquot->dq_dqb.dqb_bhardlimit);
 	limit >>= sb->s_blocksize_bits;
 
-	if (limit && buf->f_blocks > limit) {
+	if (limit) {
+		uint64_t	remaining = 0;
+
 		curblock = (dquot->dq_dqb.dqb_curspace +
 			    dquot->dq_dqb.dqb_rsvspace) >> sb->s_blocksize_bits;
-		buf->f_blocks = limit;
-		buf->f_bfree = buf->f_bavail =
-			(buf->f_blocks > curblock) ?
-			 (buf->f_blocks - curblock) : 0;
+		if (limit > curblock)
+			remaining = limit - curblock;
+
+		buf->f_blocks = min(buf->f_blocks, limit);
+		buf->f_bfree = min(buf->f_bfree, remaining);
+		buf->f_bavail = min(buf->f_bavail, remaining);
 	}
 
 	limit = min_not_zero(dquot->dq_dqb.dqb_isoftlimit,
 			     dquot->dq_dqb.dqb_ihardlimit);
-	if (limit && buf->f_files > limit) {
-		buf->f_files = limit;
-		buf->f_ffree =
-			(buf->f_files > dquot->dq_dqb.dqb_curinodes) ?
-			 (buf->f_files - dquot->dq_dqb.dqb_curinodes) : 0;
+	if (limit) {
+		uint64_t	remaining = 0;
+
+		if (limit > dquot->dq_dqb.dqb_curinodes)
+			remaining = limit - dquot->dq_dqb.dqb_curinodes;
+
+		buf->f_files = min(buf->f_files, limit);
+		buf->f_ffree = min(buf->f_ffree, remaining);
 	}
 
 	spin_unlock(&dquot->dq_dqb_lock);
@@ -6130,6 +6178,10 @@
 	if (IS_ERR(handle))
 		return PTR_ERR(handle);
 	ret = dquot_commit(dquot);
+	if (ret < 0)
+		ext4_error_err(dquot->dq_sb, -ret,
+			       "Failed to commit dquot type %d",
+			       dquot->dq_id.type);
 	err = ext4_journal_stop(handle);
 	if (!ret)
 		ret = err;
@@ -6146,6 +6198,10 @@
 	if (IS_ERR(handle))
 		return PTR_ERR(handle);
 	ret = dquot_acquire(dquot);
+	if (ret < 0)
+		ext4_error_err(dquot->dq_sb, -ret,
+			      "Failed to acquire dquot type %d",
+			      dquot->dq_id.type);
 	err = ext4_journal_stop(handle);
 	if (!ret)
 		ret = err;
@@ -6165,6 +6221,10 @@
 		return PTR_ERR(handle);
 	}
 	ret = dquot_release(dquot);
+	if (ret < 0)
+		ext4_error_err(dquot->dq_sb, -ret,
+			       "Failed to release dquot type %d",
+			       dquot->dq_id.type);
 	err = ext4_journal_stop(handle);
 	if (!ret)
 		ret = err;
@@ -6189,7 +6249,7 @@
 	handle_t *handle;
 
 	/* Data block + inode block */
-	handle = ext4_journal_start(d_inode(sb->s_root), EXT4_HT_QUOTA, 2);
+	handle = ext4_journal_start_sb(sb, EXT4_HT_QUOTA, 2);
 	if (IS_ERR(handle))
 		return PTR_ERR(handle);
 	ret = dquot_commit_info(sb, type);
@@ -6267,10 +6327,7 @@
 
 	lockdep_set_quota_inode(path->dentry->d_inode, I_DATA_SEM_QUOTA);
 	err = dquot_quota_on(sb, type, format_id, path);
-	if (err) {
-		lockdep_set_quota_inode(path->dentry->d_inode,
-					     I_DATA_SEM_NORMAL);
-	} else {
+	if (!err) {
 		struct inode *inode = d_inode(path->dentry);
 		handle_t *handle;
 
@@ -6290,10 +6347,29 @@
 		ext4_journal_stop(handle);
 	unlock_inode:
 		inode_unlock(inode);
+		if (err)
+			dquot_quota_off(sb, type);
 	}
+	if (err)
+		lockdep_set_quota_inode(path->dentry->d_inode,
+					     I_DATA_SEM_NORMAL);
 	return err;
 }
 
+static inline bool ext4_check_quota_inum(int type, unsigned long qf_inum)
+{
+	switch (type) {
+	case USRQUOTA:
+		return qf_inum == EXT4_USR_QUOTA_INO;
+	case GRPQUOTA:
+		return qf_inum == EXT4_GRP_QUOTA_INO;
+	case PRJQUOTA:
+		return qf_inum >= EXT4_GOOD_OLD_FIRST_INO;
+	default:
+		BUG();
+	}
+}
+
 static int ext4_quota_enable(struct super_block *sb, int type, int format_id,
 			     unsigned int flags)
 {
@@ -6310,9 +6386,16 @@
 	if (!qf_inums[type])
 		return -EPERM;
 
+	if (!ext4_check_quota_inum(type, qf_inums[type])) {
+		ext4_error(sb, "Bad quota inum: %lu, type: %d",
+				qf_inums[type], type);
+		return -EUCLEAN;
+	}
+
 	qf_inode = ext4_iget(sb, qf_inums[type], EXT4_IGET_SPECIAL);
 	if (IS_ERR(qf_inode)) {
-		ext4_error(sb, "Bad quota inode # %lu", qf_inums[type]);
+		ext4_error(sb, "Bad quota inode: %lu, type: %d",
+				qf_inums[type], type);
 		return PTR_ERR(qf_inode);
 	}
 
@@ -6351,10 +6434,22 @@
 			if (err) {
 				ext4_warning(sb,
 					"Failed to enable quota tracking "
-					"(type=%d, err=%d). Please run "
-					"e2fsck to fix.", type, err);
-				for (type--; type >= 0; type--)
+					"(type=%d, err=%d, ino=%lu). "
+					"Please run e2fsck to fix.", type,
+					err, qf_inums[type]);
+				for (type--; type >= 0; type--) {
+					struct inode *inode;
+
+					inode = sb_dqopt(sb)->files[type];
+					if (inode)
+						inode = igrab(inode);
 					dquot_quota_off(sb, type);
+					if (inode) {
+						lockdep_set_quota_inode(inode,
+							I_DATA_SEM_NORMAL);
+						iput(inode);
+					}
+				}
 
 				return err;
 			}
@@ -6458,7 +6553,7 @@
 	struct buffer_head *bh;
 	handle_t *handle = journal_current_handle();
 
-	if (EXT4_SB(sb)->s_journal && !handle) {
+	if (!handle) {
 		ext4_msg(sb, KERN_WARNING, "Quota write (off=%llu, len=%llu)"
 			" cancelled because transaction is not started",
 			(unsigned long long)off, (unsigned long long)len);
@@ -6641,6 +6736,7 @@
 out:
 	unregister_as_ext2();
 	unregister_as_ext3();
+	ext4_fc_destroy_dentry_cache();
 out05:
 	destroy_inodecache();
 out1:
@@ -6667,6 +6763,7 @@
 	unregister_as_ext2();
 	unregister_as_ext3();
 	unregister_filesystem(&ext4_fs_type);
+	ext4_fc_destroy_dentry_cache();
 	destroy_inodecache();
 	ext4_exit_mballoc();
 	ext4_exit_sysfs();
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/sysfs.c
@@ -489,6 +489,11 @@
 	complete(&sbi->s_kobj_unregister);
 }
 
+static void ext4_feat_release(struct kobject *kobj)
+{
+	kfree(kobj);
+}
+
 static const struct sysfs_ops ext4_attr_ops = {
 	.show	= ext4_attr_show,
 	.store	= ext4_attr_store,
@@ -503,7 +508,7 @@
 static struct kobj_type ext4_feat_ktype = {
 	.default_groups = ext4_feat_groups,
 	.sysfs_ops	= &ext4_attr_ops,
-	.release	= (void (*)(struct kobject *))kfree,
+	.release	= ext4_feat_release,
 };
 
 void ext4_notify_error_sysfs(struct ext4_sb_info *sbi)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/verity.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/verity.c
@@ -76,7 +76,7 @@
 		size_t n = min_t(size_t, count,
 				 PAGE_SIZE - offset_in_page(pos));
 		struct page *page;
-		void *fsdata;
+		void *fsdata = NULL;
 		int res;
 
 		res = pagecache_write_begin(NULL, inode->i_mapping, pos, n, 0,
@@ -364,13 +364,14 @@
 					       pgoff_t index,
 					       unsigned long num_ra_pages)
 {
-	DEFINE_READAHEAD(ractl, NULL, NULL, inode->i_mapping, index);
 	struct page *page;
 
 	index += ext4_verity_metadata_pos(inode) >> PAGE_SHIFT;
 
 	page = find_get_page_flags(inode->i_mapping, index, FGP_ACCESSED);
 	if (!page || !PageUptodate(page)) {
+		DEFINE_READAHEAD(ractl, NULL, NULL, inode->i_mapping, index);
+
 		if (page)
 			put_page(page);
 		else if (num_ra_pages > 1)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/xattr.c
@@ -123,7 +123,11 @@
 #ifdef CONFIG_LOCKDEP
 void ext4_xattr_inode_set_class(struct inode *ea_inode)
 {
+	struct ext4_inode_info *ei = EXT4_I(ea_inode);
+
 	lockdep_set_subclass(&ea_inode->i_rwsem, 1);
+	(void) ei;	/* shut up clang warning if !CONFIG_LOCKDEP */
+	lockdep_set_subclass(&ei->i_data_sem, I_DATA_SEM_EA);
 }
 #endif
 
@@ -386,7 +390,18 @@
 	struct inode *inode;
 	int err;
 
-	inode = ext4_iget(parent->i_sb, ea_ino, EXT4_IGET_NORMAL);
+	/*
+	 * We have to check for this corruption early as otherwise
+	 * iget_locked() could wait indefinitely for the state of our
+	 * parent inode.
+	 */
+	if (parent->i_ino == ea_ino) {
+		ext4_error(parent->i_sb,
+			   "Parent and EA inode have the same ino %lu", ea_ino);
+		return -EFSCORRUPTED;
+	}
+
+	inode = ext4_iget(parent->i_sb, ea_ino, EXT4_IGET_EA_INODE);
 	if (IS_ERR(inode)) {
 		err = PTR_ERR(inode);
 		ext4_error(parent->i_sb,
@@ -394,23 +409,6 @@
 			   err);
 		return err;
 	}
-
-	if (is_bad_inode(inode)) {
-		ext4_error(parent->i_sb,
-			   "error while reading EA inode %lu is_bad_inode",
-			   ea_ino);
-		err = -EIO;
-		goto error;
-	}
-
-	if (!(EXT4_I(inode)->i_flags & EXT4_EA_INODE_FL)) {
-		ext4_error(parent->i_sb,
-			   "EA inode %lu does not have EXT4_EA_INODE_FL flag",
-			    ea_ino);
-		err = -EINVAL;
-		goto error;
-	}
-
 	ext4_xattr_inode_set_class(inode);
 
 	/*
@@ -424,16 +422,28 @@
 		ext4_set_inode_state(inode, EXT4_STATE_LUSTRE_EA_INODE);
 		ext4_xattr_inode_set_ref(inode, 1);
 	} else {
-		inode_lock(inode);
+		inode_lock_nested(inode, I_MUTEX_XATTR);
 		inode->i_flags |= S_NOQUOTA;
 		inode_unlock(inode);
 	}
 
 	*ea_inode = inode;
 	return 0;
-error:
-	iput(inode);
-	return err;
+}
+
+/* Remove entry from mbcache when EA inode is getting evicted */
+void ext4_evict_ea_inode(struct inode *inode)
+{
+	struct mb_cache_entry *oe;
+
+	if (!EA_INODE_CACHE(inode))
+		return;
+	/* Wait for entry to get unused so that we can remove it */
+	while ((oe = mb_cache_entry_delete_or_get(EA_INODE_CACHE(inode),
+			ext4_xattr_inode_get_hash(inode), inode->i_ino))) {
+		mb_cache_entry_wait_unused(oe);
+		mb_cache_entry_put(EA_INODE_CACHE(inode), oe);
+	}
 }
 
 static int
@@ -976,13 +986,11 @@
 static int ext4_xattr_inode_update_ref(handle_t *handle, struct inode *ea_inode,
 				       int ref_change)
 {
-	struct mb_cache *ea_inode_cache = EA_INODE_CACHE(ea_inode);
 	struct ext4_iloc iloc;
 	s64 ref_count;
-	u32 hash;
 	int ret;
 
-	inode_lock(ea_inode);
+	inode_lock_nested(ea_inode, I_MUTEX_XATTR);
 
 	ret = ext4_reserve_inode_write(handle, ea_inode, &iloc);
 	if (ret)
@@ -1002,14 +1010,6 @@
 
 			set_nlink(ea_inode, 1);
 			ext4_orphan_del(handle, ea_inode);
-
-			if (ea_inode_cache) {
-				hash = ext4_xattr_inode_get_hash(ea_inode);
-				mb_cache_entry_create(ea_inode_cache,
-						      GFP_NOFS, hash,
-						      ea_inode->i_ino,
-						      true /* reusable */);
-			}
 		}
 	} else {
 		WARN_ONCE(ref_count < 0, "EA inode %lu ref_count=%lld",
@@ -1022,12 +1022,6 @@
 
 			clear_nlink(ea_inode);
 			ext4_orphan_add(handle, ea_inode);
-
-			if (ea_inode_cache) {
-				hash = ext4_xattr_inode_get_hash(ea_inode);
-				mb_cache_entry_delete(ea_inode_cache, hash,
-						      ea_inode->i_ino);
-			}
 		}
 	}
 
@@ -1237,6 +1231,7 @@
 	if (error)
 		goto out;
 
+retry_ref:
 	lock_buffer(bh);
 	hash = le32_to_cpu(BHDR(bh)->h_hash);
 	ref = le32_to_cpu(BHDR(bh)->h_refcount);
@@ -1246,9 +1241,18 @@
 		 * This must happen under buffer lock for
 		 * ext4_xattr_block_set() to reliably detect freed block
 		 */
-		if (ea_block_cache)
-			mb_cache_entry_delete(ea_block_cache, hash,
-					      bh->b_blocknr);
+		if (ea_block_cache) {
+			struct mb_cache_entry *oe;
+
+			oe = mb_cache_entry_delete_or_get(ea_block_cache, hash,
+							  bh->b_blocknr);
+			if (oe) {
+				unlock_buffer(bh);
+				mb_cache_entry_wait_unused(oe);
+				mb_cache_entry_put(ea_block_cache, oe);
+				goto retry_ref;
+			}
+		}
 		get_bh(bh);
 		unlock_buffer(bh);
 
@@ -1272,7 +1276,7 @@
 				ce = mb_cache_entry_get(ea_block_cache, hash,
 							bh->b_blocknr);
 				if (ce) {
-					ce->e_reusable = 1;
+					set_bit(MBE_REUSABLE_B, &ce->e_flags);
 					mb_cache_entry_put(ea_block_cache, ce);
 				}
 			}
@@ -1380,6 +1384,12 @@
 			goto out;
 
 		memcpy(bh->b_data, buf, csize);
+		/*
+		 * Zero out block tail to avoid writing uninitialized memory
+		 * to disk.
+		 */
+		if (csize < blocksize)
+			memset(bh->b_data + csize, 0, blocksize - csize);
 		set_buffer_uptodate(bh);
 		ext4_handle_dirty_metadata(handle, ea_inode, bh);
 
@@ -1413,6 +1423,13 @@
 	uid_t owner[2] = { i_uid_read(inode), i_gid_read(inode) };
 	int err;
 
+	if (inode->i_sb->s_root == NULL) {
+		ext4_warning(inode->i_sb,
+			     "refuse to create EA inode when umounting");
+		WARN_ON(1);
+		return ERR_PTR(-EINVAL);
+	}
+
 	/*
 	 * Let the next inode be the goal, so we try and allocate the EA inode
 	 * in the same group, or nearby one.
@@ -1432,6 +1449,9 @@
 		if (!err)
 			err = ext4_inode_attach_jinode(ea_inode);
 		if (err) {
+			if (ext4_xattr_inode_dec_ref(handle, ea_inode))
+				ext4_warning_inode(ea_inode,
+					"cleanup dec ref error %d", err);
 			iput(ea_inode);
 			return ERR_PTR(err);
 		}
@@ -1477,11 +1497,11 @@
 
 	while (ce) {
 		ea_inode = ext4_iget(inode->i_sb, ce->e_value,
-				     EXT4_IGET_NORMAL);
-		if (!IS_ERR(ea_inode) &&
-		    !is_bad_inode(ea_inode) &&
-		    (EXT4_I(ea_inode)->i_flags & EXT4_EA_INODE_FL) &&
-		    i_size_read(ea_inode) == value_len &&
+				     EXT4_IGET_EA_INODE);
+		if (IS_ERR(ea_inode))
+			goto next_entry;
+		ext4_xattr_inode_set_class(ea_inode);
+		if (i_size_read(ea_inode) == value_len &&
 		    !ext4_xattr_inode_read(ea_inode, ea_data, value_len) &&
 		    !ext4_xattr_inode_verify_hashes(ea_inode, NULL, ea_data,
 						    value_len) &&
@@ -1491,9 +1511,8 @@
 			kvfree(ea_data);
 			return ea_inode;
 		}
-
-		if (!IS_ERR(ea_inode))
-			iput(ea_inode);
+		iput(ea_inode);
+	next_entry:
 		ce = mb_cache_entry_find_next(ea_inode_cache, ce);
 	}
 	kvfree(ea_data);
@@ -1719,6 +1738,20 @@
 		memmove(here, (void *)here + size,
 			(void *)last - (void *)here + sizeof(__u32));
 		memset(last, 0, size);
+
+		/*
+		 * Update i_inline_off - moved ibody region might contain
+		 * system.data attribute.  Handling a failure here won't
+		 * cause other complications for setting an xattr.
+		 */
+		if (!is_block && ext4_has_inline_data(inode)) {
+			ret = ext4_find_inline_data_nolock(inode);
+			if (ret) {
+				ext4_warning_inode(inode,
+					"unable to update i_inline_off");
+				goto out;
+			}
+		}
 	} else if (s->not_found) {
 		/* Insert new name. */
 		size_t size = EXT4_XATTR_LEN(name_len);
@@ -1858,6 +1891,8 @@
 #define header(x) ((struct ext4_xattr_header *)(x))
 
 	if (s->base) {
+		int offset = (char *)s->here - bs->bh->b_data;
+
 		BUFFER_TRACE(bs->bh, "get_write_access");
 		error = ext4_journal_get_write_access(handle, sb, bs->bh,
 						      EXT4_JTR_NONE);
@@ -1873,9 +1908,20 @@
 			 * ext4_xattr_block_set() to reliably detect modified
 			 * block
 			 */
-			if (ea_block_cache)
-				mb_cache_entry_delete(ea_block_cache, hash,
-						      bs->bh->b_blocknr);
+			if (ea_block_cache) {
+				struct mb_cache_entry *oe;
+
+				oe = mb_cache_entry_delete_or_get(ea_block_cache,
+					hash, bs->bh->b_blocknr);
+				if (oe) {
+					/*
+					 * Xattr block is getting reused. Leave
+					 * it alone.
+					 */
+					mb_cache_entry_put(ea_block_cache, oe);
+					goto clone_block;
+				}
+			}
 			ea_bdebug(bs->bh, "modifying in-place");
 			error = ext4_xattr_set_entry(i, s, handle, inode,
 						     true /* is_block */);
@@ -1890,50 +1936,47 @@
 			if (error)
 				goto cleanup;
 			goto inserted;
-		} else {
-			int offset = (char *)s->here - bs->bh->b_data;
+		}
+clone_block:
+		unlock_buffer(bs->bh);
+		ea_bdebug(bs->bh, "cloning");
+		s->base = kmemdup(BHDR(bs->bh), bs->bh->b_size, GFP_NOFS);
+		error = -ENOMEM;
+		if (s->base == NULL)
+			goto cleanup;
+		s->first = ENTRY(header(s->base)+1);
+		header(s->base)->h_refcount = cpu_to_le32(1);
+		s->here = ENTRY(s->base + offset);
+		s->end = s->base + bs->bh->b_size;
 
-			unlock_buffer(bs->bh);
-			ea_bdebug(bs->bh, "cloning");
-			s->base = kmalloc(bs->bh->b_size, GFP_NOFS);
-			error = -ENOMEM;
-			if (s->base == NULL)
+		/*
+		 * If existing entry points to an xattr inode, we need
+		 * to prevent ext4_xattr_set_entry() from decrementing
+		 * ref count on it because the reference belongs to the
+		 * original block. In this case, make the entry look
+		 * like it has an empty value.
+		 */
+		if (!s->not_found && s->here->e_value_inum) {
+			ea_ino = le32_to_cpu(s->here->e_value_inum);
+			error = ext4_xattr_inode_iget(inode, ea_ino,
+				      le32_to_cpu(s->here->e_hash),
+				      &tmp_inode);
+			if (error)
 				goto cleanup;
-			memcpy(s->base, BHDR(bs->bh), bs->bh->b_size);
-			s->first = ENTRY(header(s->base)+1);
-			header(s->base)->h_refcount = cpu_to_le32(1);
-			s->here = ENTRY(s->base + offset);
-			s->end = s->base + bs->bh->b_size;
-
-			/*
-			 * If existing entry points to an xattr inode, we need
-			 * to prevent ext4_xattr_set_entry() from decrementing
-			 * ref count on it because the reference belongs to the
-			 * original block. In this case, make the entry look
-			 * like it has an empty value.
-			 */
-			if (!s->not_found && s->here->e_value_inum) {
-				ea_ino = le32_to_cpu(s->here->e_value_inum);
-				error = ext4_xattr_inode_iget(inode, ea_ino,
-					      le32_to_cpu(s->here->e_hash),
-					      &tmp_inode);
-				if (error)
-					goto cleanup;
 
-				if (!ext4_test_inode_state(tmp_inode,
-						EXT4_STATE_LUSTRE_EA_INODE)) {
-					/*
-					 * Defer quota free call for previous
-					 * inode until success is guaranteed.
-					 */
-					old_ea_inode_quota = le32_to_cpu(
-							s->here->e_value_size);
-				}
-				iput(tmp_inode);
-
-				s->here->e_value_inum = 0;
-				s->here->e_value_size = 0;
+			if (!ext4_test_inode_state(tmp_inode,
+					EXT4_STATE_LUSTRE_EA_INODE)) {
+				/*
+				 * Defer quota free call for previous
+				 * inode until success is guaranteed.
+				 */
+				old_ea_inode_quota = le32_to_cpu(
+						s->here->e_value_size);
 			}
+			iput(tmp_inode);
+
+			s->here->e_value_inum = 0;
+			s->here->e_value_size = 0;
 		}
 	} else {
 		/* Allocate a buffer where we construct the new block. */
@@ -1983,8 +2026,9 @@
 			else {
 				u32 ref;
 
+#ifdef EXT4_XATTR_DEBUG
 				WARN_ON_ONCE(dquot_initialize_needed(inode));
-
+#endif
 				/* The old block is released after updating
 				   the inode. */
 				error = dquot_alloc_block(inode,
@@ -2000,18 +2044,13 @@
 				lock_buffer(new_bh);
 				/*
 				 * We have to be careful about races with
-				 * freeing, rehashing or adding references to
-				 * xattr block. Once we hold buffer lock xattr
-				 * block's state is stable so we can check
-				 * whether the block got freed / rehashed or
-				 * not.  Since we unhash mbcache entry under
-				 * buffer lock when freeing / rehashing xattr
-				 * block, checking whether entry is still
-				 * hashed is reliable. Same rules hold for
-				 * e_reusable handling.
+				 * adding references to xattr block. Once we
+				 * hold buffer lock xattr block's state is
+				 * stable so we can check the additional
+				 * reference fits.
 				 */
-				if (hlist_bl_unhashed(&ce->e_hash_list) ||
-				    !ce->e_reusable) {
+				ref = le32_to_cpu(BHDR(new_bh)->h_refcount) + 1;
+				if (ref > EXT4_XATTR_REFCOUNT_MAX) {
 					/*
 					 * Undo everything and check mbcache
 					 * again.
@@ -2026,10 +2065,9 @@
 					new_bh = NULL;
 					goto inserted;
 				}
-				ref = le32_to_cpu(BHDR(new_bh)->h_refcount) + 1;
 				BHDR(new_bh)->h_refcount = cpu_to_le32(ref);
-				if (ref >= EXT4_XATTR_REFCOUNT_MAX)
-					ce->e_reusable = 0;
+				if (ref == EXT4_XATTR_REFCOUNT_MAX)
+					clear_bit(MBE_REUSABLE_B, &ce->e_flags);
 				ea_bdebug(new_bh, "reusing; refcount now=%d",
 					  ref);
 				ext4_xattr_block_csum_set(inode, new_bh);
@@ -2053,23 +2091,16 @@
 			/* We need to allocate a new block */
 			ext4_fsblk_t goal, block;
 
+#ifdef EXT4_XATTR_DEBUG
 			WARN_ON_ONCE(dquot_initialize_needed(inode));
-
+#endif
 			goal = ext4_group_first_block_no(sb,
 						EXT4_I(inode)->i_block_group);
-
-			/* non-extent files can't have physical blocks past 2^32 */
-			if (!(ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS)))
-				goal = goal & EXT4_MAX_BLOCK_FILE_PHYS;
-
 			block = ext4_new_meta_blocks(handle, inode, goal, 0,
 						     NULL, &error);
 			if (error)
 				goto cleanup;
 
-			if (!(ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS)))
-				BUG_ON(block > EXT4_MAX_BLOCK_FILE_PHYS);
-
 			ea_idebug(inode, "creating block %llu",
 				  (unsigned long long)block);
 
@@ -2176,8 +2207,9 @@
 	struct ext4_inode *raw_inode;
 	int error;
 
-	if (EXT4_I(inode)->i_extra_isize == 0)
+	if (!EXT4_INODE_HAS_XATTR_SPACE(inode))
 		return 0;
+
 	raw_inode = ext4_raw_inode(&is->iloc);
 	header = IHDR(inode, raw_inode);
 	is->s.base = is->s.first = IFIRST(header);
@@ -2205,8 +2237,9 @@
 	struct ext4_xattr_search *s = &is->s;
 	int error;
 
-	if (EXT4_I(inode)->i_extra_isize == 0)
+	if (!EXT4_INODE_HAS_XATTR_SPACE(inode))
 		return -ENOSPC;
+
 	error = ext4_xattr_set_entry(i, s, handle, inode, false /* is_block */);
 	if (error)
 		return error;
@@ -2408,7 +2441,7 @@
 		if (IS_SYNC(inode))
 			ext4_handle_sync(handle);
 	}
-	ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR);
+	ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR, handle);
 
 cleanup:
 	brelse(is.iloc.bh);
@@ -2479,6 +2512,8 @@
 
 		error = ext4_xattr_set_handle(handle, inode, name_index, name,
 					      value, value_len, flags);
+		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR,
+					handle);
 		error2 = ext4_journal_stop(handle);
 		if (error == -ENOSPC &&
 		    ext4_should_retry_alloc(sb, &retries))
@@ -2486,7 +2521,6 @@
 		if (error == 0)
 			error = error2;
 	}
-	ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR);
 
 	return error;
 }
@@ -2535,13 +2569,13 @@
 		.in_inode = !!entry->e_value_inum,
 	};
 	struct ext4_xattr_ibody_header *header = IHDR(inode, raw_inode);
+	int needs_kvfree = 0;
 	int error;
 
 	is = kzalloc(sizeof(struct ext4_xattr_ibody_find), GFP_NOFS);
 	bs = kzalloc(sizeof(struct ext4_xattr_block_find), GFP_NOFS);
-	buffer = kmalloc(value_size, GFP_NOFS);
 	b_entry_name = kmalloc(entry->e_name_len + 1, GFP_NOFS);
-	if (!is || !bs || !buffer || !b_entry_name) {
+	if (!is || !bs || !b_entry_name) {
 		error = -ENOMEM;
 		goto out;
 	}
@@ -2553,12 +2587,18 @@
 
 	/* Save the entry name and the entry value */
 	if (entry->e_value_inum) {
+		buffer = kvmalloc(value_size, GFP_NOFS);
+		if (!buffer) {
+			error = -ENOMEM;
+			goto out;
+		}
+		needs_kvfree = 1;
 		error = ext4_xattr_inode_get(inode, entry, buffer, value_size);
 		if (error)
 			goto out;
 	} else {
 		size_t value_offs = le16_to_cpu(entry->e_value_offs);
-		memcpy(buffer, (void *)IFIRST(header) + value_offs, value_size);
+		buffer = (void *)IFIRST(header) + value_offs;
 	}
 
 	memcpy(b_entry_name, entry->e_name, entry->e_name_len);
@@ -2573,25 +2613,26 @@
 	if (error)
 		goto out;
 
-	/* Remove the chosen entry from the inode */
-	error = ext4_xattr_ibody_set(handle, inode, &i, is);
-	if (error)
-		goto out;
-
 	i.value = buffer;
 	i.value_len = value_size;
 	error = ext4_xattr_block_find(inode, &i, bs);
 	if (error)
 		goto out;
 
-	/* Add entry which was removed from the inode into the block */
+	/* Move ea entry from the inode into the block */
 	error = ext4_xattr_block_set(handle, inode, &i, bs);
 	if (error)
 		goto out;
-	error = 0;
+
+	/* Remove the chosen entry from the inode */
+	i.value = NULL;
+	i.value_len = 0;
+	error = ext4_xattr_ibody_set(handle, inode, &i, is);
+
 out:
 	kfree(b_entry_name);
-	kfree(buffer);
+	if (needs_kvfree && buffer)
+		kvfree(buffer);
 	if (is)
 		brelse(is->iloc.bh);
 	if (bs)
@@ -2766,6 +2807,9 @@
 			(void *)header, total_ino);
 	EXT4_I(inode)->i_extra_isize = new_extra_isize;
 
+	if (ext4_has_inline_data(inode))
+		error = ext4_find_inline_data_nolock(inode);
+
 cleanup:
 	if (error && (mnt_count != le16_to_cpu(sbi->s_es->s_mnt_count))) {
 		ext4_warning(inode->i_sb, "Unable to expand inode %lu. Delete some EAs or run e2fsck.",
@@ -2920,7 +2964,7 @@
 					 error);
 			goto cleanup;
 		}
-		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR);
+		ext4_fc_mark_ineligible(inode->i_sb, EXT4_FC_REASON_XATTR, handle);
 	}
 	error = 0;
 cleanup:
@@ -3038,8 +3082,10 @@
 
 		bh = ext4_sb_bread(inode->i_sb, ce->e_value, REQ_PRIO);
 		if (IS_ERR(bh)) {
-			if (PTR_ERR(bh) == -ENOMEM)
+			if (PTR_ERR(bh) == -ENOMEM) {
+				mb_cache_entry_put(ea_block_cache, ce);
 				return NULL;
+			}
 			bh = NULL;
 			EXT4_ERROR_INODE(inode, "block %lu read error",
 					 (unsigned long)ce->e_value);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ext4/xattr.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ext4/xattr.h
@@ -95,6 +95,19 @@
 
 #define EXT4_ZERO_XATTR_VALUE ((void *)-1)
 
+/*
+ * If we want to add an xattr to the inode, we should make sure that
+ * i_extra_isize is not 0 and that the inode size is not less than
+ * EXT4_GOOD_OLD_INODE_SIZE + extra_isize + pad.
+ *   EXT4_GOOD_OLD_INODE_SIZE   extra_isize header   entry   pad  data
+ * |--------------------------|------------|------|---------|---|-------|
+ */
+#define EXT4_INODE_HAS_XATTR_SPACE(inode)				\
+	((EXT4_I(inode)->i_extra_isize != 0) &&				\
+	 (EXT4_GOOD_OLD_INODE_SIZE + EXT4_I(inode)->i_extra_isize +	\
+	  sizeof(struct ext4_xattr_ibody_header) + EXT4_XATTR_PAD <=	\
+	  EXT4_INODE_SIZE((inode)->i_sb)))
+
 struct ext4_xattr_info {
 	const char *name;
 	const void *value;
@@ -178,6 +191,7 @@
 
 extern int ext4_expand_extra_isize_ea(struct inode *inode, int new_extra_isize,
 			    struct ext4_inode *raw_inode, handle_t *handle);
+extern void ext4_evict_ea_inode(struct inode *inode);
 
 extern const struct xattr_handler *ext4_xattr_handlers[];
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/checkpoint.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/checkpoint.c
@@ -66,7 +66,7 @@
 		.old_blkaddr = index,
 		.new_blkaddr = index,
 		.encrypted_page = NULL,
-		.is_por = !is_meta,
+		.is_por = !is_meta ? 1 : 0,
 	};
 	int err;
 
@@ -139,7 +139,7 @@
 	unsigned int segno, offset;
 	bool exist;
 
-	if (type != DATA_GENERIC_ENHANCE && type != DATA_GENERIC_ENHANCE_READ)
+	if (type == DATA_GENERIC)
 		return true;
 
 	segno = GET_SEGNO(sbi, blkaddr);
@@ -147,11 +147,18 @@
 	se = get_seg_entry(sbi, segno);
 
 	exist = f2fs_test_bit(offset, se->cur_valid_map);
+	if (exist && type == DATA_GENERIC_ENHANCE_UPDATE) {
+		f2fs_err(sbi, "Inconsistent error blkaddr:%u, sit bitmap:%d",
+			 blkaddr, exist);
+		set_sbi_flag(sbi, SBI_NEED_FSCK);
+		return exist;
+	}
+
 	if (!exist && type == DATA_GENERIC_ENHANCE) {
 		f2fs_err(sbi, "Inconsistent error blkaddr:%u, sit bitmap:%d",
 			 blkaddr, exist);
 		set_sbi_flag(sbi, SBI_NEED_FSCK);
-		WARN_ON(1);
+		dump_stack();
 	}
 	return exist;
 }
@@ -184,12 +191,13 @@
 	case DATA_GENERIC:
 	case DATA_GENERIC_ENHANCE:
 	case DATA_GENERIC_ENHANCE_READ:
+	case DATA_GENERIC_ENHANCE_UPDATE:
 		if (unlikely(blkaddr >= MAX_BLKADDR(sbi) ||
 				blkaddr < MAIN_BLKADDR(sbi))) {
 			f2fs_warn(sbi, "access invalid blkaddr:%u",
 				  blkaddr);
 			set_sbi_flag(sbi, SBI_NEED_FSCK);
-			WARN_ON(1);
+			dump_stack();
 			return false;
 		} else {
 			return __is_bitmap_valid(sbi, blkaddr, type);
@@ -221,8 +229,8 @@
 		.op = REQ_OP_READ,
 		.op_flags = sync ? (REQ_META | REQ_PRIO) : REQ_RAHEAD,
 		.encrypted_page = NULL,
-		.in_list = false,
-		.is_por = (type == META_POR),
+		.in_list = 0,
+		.is_por = (type == META_POR) ? 1 : 0,
 	};
 	struct blk_plug plug;
 	int err;
@@ -304,8 +312,15 @@
 
 	trace_f2fs_writepage(page, META);
 
-	if (unlikely(f2fs_cp_error(sbi)))
+	if (unlikely(f2fs_cp_error(sbi))) {
+		if (is_sbi_flag_set(sbi, SBI_IS_CLOSE)) {
+			ClearPageUptodate(page);
+			dec_page_count(sbi, F2FS_DIRTY_META);
+			unlock_page(page);
+			return 0;
+		}
 		goto redirty_out;
+	}
 	if (unlikely(is_sbi_flag_set(sbi, SBI_POR_DOING)))
 		goto redirty_out;
 	if (wbc->for_reclaim && page->index < GET_SUM_BLOCK(sbi, 0))
@@ -653,7 +668,7 @@
 		return PTR_ERR(inode);
 	}
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err) {
 		iput(inode);
 		goto err_out;
@@ -664,7 +679,7 @@
 	/* truncate all the data during iput */
 	iput(inode);
 
-	err = f2fs_get_node_info(sbi, ino, &ni);
+	err = f2fs_get_node_info(sbi, ino, &ni, false);
 	if (err)
 		goto err_out;
 
@@ -777,7 +792,7 @@
 	 */
 	head = &im->ino_list;
 
-	/* loop for each orphan inode entry and write them in Jornal block */
+	/* loop for each orphan inode entry and write them in journal block */
 	list_for_each_entry(orphan, head, list) {
 		if (!page) {
 			page = f2fs_grab_meta_page(sbi, start_blk++);
@@ -867,6 +882,7 @@
 	struct page *cp_page_1 = NULL, *cp_page_2 = NULL;
 	struct f2fs_checkpoint *cp_block = NULL;
 	unsigned long long cur_version = 0, pre_version = 0;
+	unsigned int cp_blocks;
 	int err;
 
 	err = get_checkpoint_version(sbi, cp_addr, &cp_block,
@@ -874,15 +890,16 @@
 	if (err)
 		return NULL;
 
-	if (le32_to_cpu(cp_block->cp_pack_total_block_count) >
-					sbi->blocks_per_seg) {
+	cp_blocks = le32_to_cpu(cp_block->cp_pack_total_block_count);
+
+	if (cp_blocks > sbi->blocks_per_seg || cp_blocks <= F2FS_CP_PACKS) {
 		f2fs_warn(sbi, "invalid cp_pack_total_block_count:%u",
 			  le32_to_cpu(cp_block->cp_pack_total_block_count));
 		goto invalid_cp;
 	}
 	pre_version = *version;
 
-	cp_addr += le32_to_cpu(cp_block->cp_pack_total_block_count) - 1;
+	cp_addr += cp_blocks - 1;
 	err = get_checkpoint_version(sbi, cp_addr, &cp_block,
 					&cp_page_2, version);
 	if (err)
@@ -1052,7 +1069,8 @@
 	spin_unlock(&sbi->inode_lock[type]);
 }
 
-int f2fs_sync_dirty_inodes(struct f2fs_sb_info *sbi, enum inode_type type)
+int f2fs_sync_dirty_inodes(struct f2fs_sb_info *sbi, enum inode_type type,
+						bool from_cp)
 {
 	struct list_head *head;
 	struct inode *inode;
@@ -1087,11 +1105,15 @@
 	if (inode) {
 		unsigned long cur_ino = inode->i_ino;
 
-		F2FS_I(inode)->cp_task = current;
+		if (from_cp)
+			F2FS_I(inode)->cp_task = current;
+		F2FS_I(inode)->wb_task = current;
 
 		filemap_fdatawrite(inode->i_mapping);
 
-		F2FS_I(inode)->cp_task = NULL;
+		F2FS_I(inode)->wb_task = NULL;
+		if (from_cp)
+			F2FS_I(inode)->cp_task = NULL;
 
 		iput(inode);
 		/* We need to give cpu to another writers. */
@@ -1102,7 +1124,7 @@
 	} else {
 		/*
 		 * We should submit bio, since it exists several
-		 * wribacking dentry pages in the freeing inode.
+		 * writebacking dentry pages in the freeing inode.
 		 */
 		f2fs_submit_merged_write(sbi, DATA);
 		cond_resched();
@@ -1162,7 +1184,8 @@
 	if (!is_journalled_quota(sbi))
 		return false;
 
-	down_write(&sbi->quota_sem);
+	if (!down_write_trylock(&sbi->quota_sem))
+		return true;
 	if (is_sbi_flag_set(sbi, SBI_QUOTA_SKIP_FLUSH)) {
 		ret = false;
 	} else if (is_sbi_flag_set(sbi, SBI_QUOTA_NEED_REPAIR)) {
@@ -1219,7 +1242,7 @@
 	/* write all the dirty dentry pages */
 	if (get_pages(sbi, F2FS_DIRTY_DENTS)) {
 		f2fs_unlock_all(sbi);
-		err = f2fs_sync_dirty_inodes(sbi, DIR_INODE);
+		err = f2fs_sync_dirty_inodes(sbi, DIR_INODE, true);
 		if (err)
 			return err;
 		cond_resched();
@@ -1282,7 +1305,8 @@
 		if (!get_pages(sbi, type))
 			break;
 
-		if (unlikely(f2fs_cp_error(sbi)))
+		if (unlikely(f2fs_cp_error(sbi) &&
+			!is_sbi_flag_set(sbi, SBI_IS_CLOSE)))
 			break;
 
 		if (type == F2FS_DIRTY_META)
@@ -1304,8 +1328,8 @@
 	unsigned long flags;
 
 	if (cpc->reason & CP_UMOUNT) {
-		if (le32_to_cpu(ckpt->cp_pack_total_block_count) >
-			sbi->blocks_per_seg - NM_I(sbi)->nat_bits_blocks) {
+		if (le32_to_cpu(ckpt->cp_pack_total_block_count) +
+			NM_I(sbi)->nat_bits_blocks > sbi->blocks_per_seg) {
 			clear_ckpt_flags(sbi, CP_NAT_BITS_FLAG);
 			f2fs_notice(sbi, "Disable nat_bits due to no space");
 		} else if (!is_set_ckpt_flags(sbi, CP_NAT_BITS_FLAG) &&
@@ -1889,15 +1913,27 @@
 void f2fs_stop_ckpt_thread(struct f2fs_sb_info *sbi)
 {
 	struct ckpt_req_control *cprc = &sbi->cprc_info;
+	struct task_struct *ckpt_task;
 
-	if (cprc->f2fs_issue_ckpt) {
-		struct task_struct *ckpt_task = cprc->f2fs_issue_ckpt;
+	if (!cprc->f2fs_issue_ckpt)
+		return;
 
-		cprc->f2fs_issue_ckpt = NULL;
-		kthread_stop(ckpt_task);
+	ckpt_task = cprc->f2fs_issue_ckpt;
+	cprc->f2fs_issue_ckpt = NULL;
+	kthread_stop(ckpt_task);
 
-		flush_remained_ckpt_reqs(sbi, NULL);
-	}
+	f2fs_flush_ckpt_thread(sbi);
+}
+
+void f2fs_flush_ckpt_thread(struct f2fs_sb_info *sbi)
+{
+	struct ckpt_req_control *cprc = &sbi->cprc_info;
+
+	flush_remained_ckpt_reqs(sbi, NULL);
+
+	/* Let's wait for the previous dispatched checkpoint. */
+	while (atomic_read(&cprc->queued_ckpt))
+		io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 }
 
 void f2fs_init_ckpt_req_control(struct f2fs_sb_info *sbi)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/compress.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/compress.c
@@ -312,10 +312,9 @@
 	}
 
 	if (ret != PAGE_SIZE << dic->log_cluster_size) {
-		printk_ratelimited("%sF2FS-fs (%s): lz4 invalid rlen:%zu, "
+		printk_ratelimited("%sF2FS-fs (%s): lz4 invalid ret:%d, "
 					"expected:%lu\n", KERN_ERR,
-					F2FS_I_SB(dic->inode)->sb->s_id,
-					dic->rlen,
+					F2FS_I_SB(dic->inode)->sb->s_id, ret,
 					PAGE_SIZE << dic->log_cluster_size);
 		return -EIO;
 	}
@@ -1038,8 +1037,10 @@
 	int i;
 
 	for (i = 0; i < cc->cluster_size; i++)
-		if (cc->rpages[i])
+		if (cc->rpages[i]) {
 			set_page_dirty(cc->rpages[i]);
+			set_page_private_gcing(cc->rpages[i]);
+		}
 }
 
 static int prepare_compress_overwrite(struct compress_ctx *cc,
@@ -1232,10 +1233,11 @@
 		.page = NULL,
 		.encrypted_page = NULL,
 		.compressed_page = NULL,
-		.submitted = false,
+		.submitted = 0,
 		.io_type = io_type,
 		.io_wbc = wbc,
-		.encrypted = fscrypt_inode_uses_fs_layer_crypto(cc->inode),
+		.encrypted = fscrypt_inode_uses_fs_layer_crypto(cc->inode) ?
+									1 : 0,
 	};
 	struct dnode_of_data dn;
 	struct node_info ni;
@@ -1245,7 +1247,7 @@
 	loff_t psize;
 	int i, err;
 
-	/* we should bypass data pages to proceed the kworkder jobs */
+	/* we should bypass data pages to proceed the kworker jobs */
 	if (unlikely(f2fs_cp_error(sbi))) {
 		mapping_set_error(cc->rpages[0]->mapping, -EIO);
 		goto out_free;
@@ -1276,7 +1278,7 @@
 
 	psize = (loff_t)(cc->rpages[last_index]->index + 1) << PAGE_SHIFT;
 
-	err = f2fs_get_node_info(fio.sbi, dn.nid, &ni);
+	err = f2fs_get_node_info(fio.sbi, dn.nid, &ni, false);
 	if (err)
 		goto out_put_dnode;
 
@@ -1443,32 +1445,57 @@
 }
 
 static int f2fs_write_raw_pages(struct compress_ctx *cc,
-					int *submitted,
+					int *submitted_p,
 					struct writeback_control *wbc,
 					enum iostat_type io_type)
 {
 	struct address_space *mapping = cc->inode->i_mapping;
-	int _submitted, compr_blocks, ret;
-	int i = -1, err = 0;
+	struct f2fs_sb_info *sbi = F2FS_M_SB(mapping);
+	int submitted, compr_blocks, i;
+	int ret = 0;
 
 	compr_blocks = f2fs_compressed_blocks(cc);
-	if (compr_blocks < 0) {
-		err = compr_blocks;
-		goto out_err;
+
+	for (i = 0; i < cc->cluster_size; i++) {
+		if (!cc->rpages[i])
+			continue;
+
+		redirty_page_for_writepage(wbc, cc->rpages[i]);
+		unlock_page(cc->rpages[i]);
 	}
 
+	if (compr_blocks < 0)
+		return compr_blocks;
+
+	/* overwrite compressed cluster w/ normal cluster */
+	if (compr_blocks > 0)
+		f2fs_lock_op(sbi);
+
 	for (i = 0; i < cc->cluster_size; i++) {
 		if (!cc->rpages[i])
 			continue;
 retry_write:
+		lock_page(cc->rpages[i]);
+
 		if (cc->rpages[i]->mapping != mapping) {
+continue_unlock:
 			unlock_page(cc->rpages[i]);
 			continue;
 		}
 
-		BUG_ON(!PageLocked(cc->rpages[i]));
+		if (!PageDirty(cc->rpages[i]))
+			goto continue_unlock;
+
+		if (PageWriteback(cc->rpages[i])) {
+			if (wbc->sync_mode == WB_SYNC_NONE)
+				goto continue_unlock;
+			f2fs_wait_on_page_writeback(cc->rpages[i], DATA, true, true);
+		}
+
+		if (!clear_page_dirty_for_io(cc->rpages[i]))
+			goto continue_unlock;
 
-		ret = f2fs_write_single_data_page(cc->rpages[i], &_submitted,
+		ret = f2fs_write_single_data_page(cc->rpages[i], &submitted,
 						NULL, NULL, wbc, io_type,
 						compr_blocks, false);
 		if (ret) {
@@ -1476,47 +1503,29 @@
 				unlock_page(cc->rpages[i]);
 				ret = 0;
 			} else if (ret == -EAGAIN) {
+				ret = 0;
 				/*
 				 * for quota file, just redirty left pages to
 				 * avoid deadlock caused by cluster update race
 				 * from foreground operation.
 				 */
-				if (IS_NOQUOTA(cc->inode)) {
-					err = 0;
-					goto out_err;
-				}
-				ret = 0;
-				cond_resched();
-				congestion_wait(BLK_RW_ASYNC,
-						DEFAULT_IO_TIMEOUT);
-				lock_page(cc->rpages[i]);
-
-				if (!PageDirty(cc->rpages[i])) {
-					unlock_page(cc->rpages[i]);
-					continue;
-				}
-
-				clear_page_dirty_for_io(cc->rpages[i]);
+				if (IS_NOQUOTA(cc->inode))
+					goto out;
+				f2fs_io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 				goto retry_write;
 			}
-			err = ret;
-			goto out_err;
+			goto out;
 		}
 
-		*submitted += _submitted;
+		*submitted_p += submitted;
 	}
 
-	f2fs_balance_fs(F2FS_M_SB(mapping), true);
+out:
+	if (compr_blocks > 0)
+		f2fs_unlock_op(sbi);
 
-	return 0;
-out_err:
-	for (++i; i < cc->cluster_size; i++) {
-		if (!cc->rpages[i])
-			continue;
-		redirty_page_for_writepage(wbc, cc->rpages[i]);
-		unlock_page(cc->rpages[i]);
-	}
-	return err;
+	f2fs_balance_fs(sbi, true);
+	return ret;
 }
 
 int f2fs_write_multi_pages(struct compress_ctx *cc,
@@ -1530,6 +1539,7 @@
 	if (cluster_may_compress(cc)) {
 		err = f2fs_compress_pages(cc);
 		if (err == -EAGAIN) {
+			add_compr_block_stat(cc->inode, cc->cluster_size);
 			goto write;
 		} else if (err) {
 			f2fs_put_rpages_wbc(cc, wbc, true, 1);
@@ -1906,7 +1916,7 @@
 int f2fs_init_page_array_cache(struct f2fs_sb_info *sbi)
 {
 	dev_t dev = sbi->sb->s_bdev->bd_dev;
-	char slab_name[32];
+	char slab_name[35];
 
 	sprintf(slab_name, "f2fs_page_array_entry-%u:%u", MAJOR(dev), MINOR(dev));
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/data.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/data.c
@@ -677,7 +677,7 @@
 	}
 
 	if (fio->io_wbc && !is_read_io(fio->op))
-		wbc_account_cgroup_owner(fio->io_wbc, page, PAGE_SIZE);
+		wbc_account_cgroup_owner(fio->io_wbc, fio->page, PAGE_SIZE);
 
 	__attach_io_flag(fio);
 	bio_set_op_attrs(bio, fio->op, fio->op_flags);
@@ -808,6 +808,8 @@
 	bool found = false;
 	struct bio *target = bio ? *bio : NULL;
 
+	f2fs_bug_on(sbi, !target && !page);
+
 	for (temp = HOT; temp < NR_TEMP_TYPE && !found; temp++) {
 		struct f2fs_bio_info *io = sbi->write_io[DATA] + temp;
 		struct list_head *head = &io->bio_list;
@@ -887,7 +889,7 @@
 	}
 
 	if (fio->io_wbc)
-		wbc_account_cgroup_owner(fio->io_wbc, page, PAGE_SIZE);
+		wbc_account_cgroup_owner(fio->io_wbc, fio->page, PAGE_SIZE);
 
 	inc_page_count(fio->sbi, WB_DATA_TYPE(page));
 
@@ -930,7 +932,7 @@
 		bio_page = fio->page;
 
 	/* set submitted = true as a return value */
-	fio->submitted = true;
+	fio->submitted = 1;
 
 	inc_page_count(sbi, WB_DATA_TYPE(bio_page));
 
@@ -946,7 +948,7 @@
 				(fio->type == DATA || fio->type == NODE) &&
 				fio->new_blkaddr & F2FS_IO_SIZE_MASK(sbi)) {
 			dec_page_count(sbi, WB_DATA_TYPE(bio_page));
-			fio->retry = true;
+			fio->retry = 1;
 			goto skip;
 		}
 		io->bio = __bio_alloc(fio, BIO_MAX_VECS);
@@ -961,7 +963,7 @@
 	}
 
 	if (fio->io_wbc)
-		wbc_account_cgroup_owner(fio->io_wbc, bio_page, PAGE_SIZE);
+		wbc_account_cgroup_owner(fio->io_wbc, fio->page, PAGE_SIZE);
 
 	io->last_block_in_bio = fio->new_blkaddr;
 
@@ -1354,7 +1356,7 @@
 	if (unlikely(is_inode_flag_set(dn->inode, FI_NO_ALLOC)))
 		return -EPERM;
 
-	err = f2fs_get_node_info(sbi, dn->nid, &ni);
+	err = f2fs_get_node_info(sbi, dn->nid, &ni, false);
 	if (err)
 		return err;
 
@@ -1465,10 +1467,15 @@
 	struct extent_info ei = {0, };
 	block_t blkaddr;
 	unsigned int start_pgofs;
+	int bidx = 0;
 
 	if (!maxblocks)
 		return 0;
 
+	map->m_bdev = inode->i_sb->s_bdev;
+	map->m_multidev_dio =
+		f2fs_allow_multi_device_dio(F2FS_I_SB(inode), flag);
+
 	map->m_len = 0;
 	map->m_flags = 0;
 
@@ -1491,6 +1498,21 @@
 		if (flag == F2FS_GET_BLOCK_DIO)
 			f2fs_wait_on_block_writeback_range(inode,
 						map->m_pblk, map->m_len);
+
+		if (map->m_multidev_dio) {
+			block_t blk_addr = map->m_pblk;
+
+			bidx = f2fs_target_device_index(sbi, map->m_pblk);
+
+			map->m_bdev = FDEV(bidx).bdev;
+			map->m_pblk -= FDEV(bidx).start_blk;
+			map->m_len = min(map->m_len,
+				FDEV(bidx).end_blk + 1 - map->m_pblk);
+
+			if (map->m_may_create)
+				f2fs_update_device_state(sbi, inode->i_ino,
+							blk_addr, map->m_len);
+		}
 		goto out;
 	}
 
@@ -1609,6 +1631,9 @@
 	if (flag == F2FS_GET_BLOCK_PRE_AIO)
 		goto skip;
 
+	if (map->m_multidev_dio)
+		bidx = f2fs_target_device_index(sbi, blkaddr);
+
 	if (map->m_len == 0) {
 		/* preallocated unwritten block should be mapped for fiemap. */
 		if (blkaddr == NEW_ADDR)
@@ -1617,10 +1642,15 @@
 
 		map->m_pblk = blkaddr;
 		map->m_len = 1;
+
+		if (map->m_multidev_dio)
+			map->m_bdev = FDEV(bidx).bdev;
 	} else if ((map->m_pblk != NEW_ADDR &&
 			blkaddr == (map->m_pblk + ofs)) ||
 			(map->m_pblk == NEW_ADDR && blkaddr == NEW_ADDR) ||
 			flag == F2FS_GET_BLOCK_PRE_DIO) {
+		if (map->m_multidev_dio && map->m_bdev != FDEV(bidx).bdev)
+			goto sync_out;
 		ofs++;
 		map->m_len++;
 	} else {
@@ -1673,11 +1703,31 @@
 
 sync_out:
 
-	/* for hardware encryption, but to avoid potential issue in future */
-	if (flag == F2FS_GET_BLOCK_DIO && map->m_flags & F2FS_MAP_MAPPED)
+	if (flag == F2FS_GET_BLOCK_DIO && map->m_flags & F2FS_MAP_MAPPED) {
+		/*
+		 * for hardware encryption, but to avoid potential issue
+		 * in future
+		 */
 		f2fs_wait_on_block_writeback_range(inode,
 						map->m_pblk, map->m_len);
 
+		if (map->m_multidev_dio) {
+			block_t blk_addr = map->m_pblk;
+
+			bidx = f2fs_target_device_index(sbi, map->m_pblk);
+
+			map->m_bdev = FDEV(bidx).bdev;
+			map->m_pblk -= FDEV(bidx).start_blk;
+
+			if (map->m_may_create)
+				f2fs_update_device_state(sbi, inode->i_ino,
+							blk_addr, map->m_len);
+
+			f2fs_bug_on(sbi, blk_addr + map->m_len >
+						FDEV(bidx).end_blk + 1);
+		}
+	}
+
 	if (flag == F2FS_GET_BLOCK_PRECACHE) {
 		if (map->m_flags & F2FS_MAP_MAPPED) {
 			unsigned int ofs = start_pgofs - map->m_lblk;
@@ -1696,7 +1746,7 @@
 		f2fs_balance_fs(sbi, dn.node_changed);
 	}
 out:
-	trace_f2fs_map_blocks(inode, map, err);
+	trace_f2fs_map_blocks(inode, map, create, flag, err);
 	return err;
 }
 
@@ -1755,6 +1805,9 @@
 		map_bh(bh, inode->i_sb, map.m_pblk);
 		bh->b_state = (bh->b_state & ~F2FS_MAP_FLAGS) | map.m_flags;
 		bh->b_size = blks_to_bytes(inode, map.m_len);
+
+		if (map.m_multidev_dio)
+			bh->b_bdev = map.m_bdev;
 	}
 	return err;
 }
@@ -1796,7 +1849,7 @@
 		if (!page)
 			return -ENOMEM;
 
-		err = f2fs_get_node_info(sbi, inode->i_ino, &ni);
+		err = f2fs_get_node_info(sbi, inode->i_ino, &ni, false);
 		if (err) {
 			f2fs_put_page(page, 1);
 			return err;
@@ -1828,7 +1881,7 @@
 		if (!page)
 			return -ENOMEM;
 
-		err = f2fs_get_node_info(sbi, xnid, &ni);
+		err = f2fs_get_node_info(sbi, xnid, &ni, false);
 		if (err) {
 			f2fs_put_page(page, 1);
 			return err;
@@ -2251,8 +2304,10 @@
 		f2fs_wait_on_block_writeback(inode, blkaddr);
 
 		if (f2fs_load_compressed_page(sbi, page, blkaddr)) {
-			if (atomic_dec_and_test(&dic->remaining_pages))
+			if (atomic_dec_and_test(&dic->remaining_pages)) {
 				f2fs_decompress_cluster(dic);
+				break;
+			}
 			continue;
 		}
 
@@ -2357,7 +2412,7 @@
 
 #ifdef CONFIG_F2FS_FS_COMPRESSION
 		if (f2fs_compressed_file(inode)) {
-			/* there are remained comressed pages, submit them */
+			/* there are remained compressed pages, submit them */
 			if (!f2fs_cluster_can_merge_page(&cc, page->index)) {
 				ret = f2fs_read_multi_pages(&cc, &bio,
 							max_nr_pages,
@@ -2512,6 +2567,9 @@
 	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	unsigned int policy = SM_I(sbi)->ipu_policy;
 
+	if (policy & (0x1 << F2FS_IPU_HONOR_OPU_WRITE) &&
+			is_inode_flag_set(inode, FI_OPU_WRITE))
+		return false;
 	if (policy & (0x1 << F2FS_IPU_FORCE))
 		return true;
 	if (policy & (0x1 << F2FS_IPU_SSR) && f2fs_need_SSR(sbi))
@@ -2564,6 +2622,11 @@
 {
 	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 
+	/* The below cases were checked when setting it. */
+	if (f2fs_is_pinned_file(inode))
+		return false;
+	if (fio && is_sbi_flag_set(sbi, SBI_NEED_FSCK))
+		return true;
 	if (f2fs_lfs_mode(sbi))
 		return true;
 	if (S_ISDIR(inode->i_mode))
@@ -2572,13 +2635,14 @@
 		return true;
 	if (f2fs_is_atomic_file(inode))
 		return true;
-	if (is_sbi_flag_set(sbi, SBI_NEED_FSCK))
-		return true;
 
 	/* swap file is migrating in aligned write mode */
 	if (is_inode_flag_set(inode, FI_ALIGNED_WRITE))
 		return true;
 
+	if (is_inode_flag_set(inode, FI_OPU_WRITE))
+		return true;
+
 	if (fio) {
 		if (page_private_gcing(fio->page))
 			return true;
@@ -2685,7 +2749,7 @@
 		fio->need_lock = LOCK_REQ;
 	}
 
-	err = f2fs_get_node_info(fio->sbi, dn.nid, &ni);
+	err = f2fs_get_node_info(fio->sbi, dn.nid, &ni, false);
 	if (err)
 		goto out_writepage;
 
@@ -2741,9 +2805,10 @@
 		.old_blkaddr = NULL_ADDR,
 		.page = page,
 		.encrypted_page = NULL,
-		.submitted = false,
+		.submitted = 0,
 		.compr_blocks = compr_blocks,
-		.need_lock = LOCK_RETRY,
+		.need_lock = compr_blocks ? LOCK_DONE : LOCK_RETRY,
+		.post_read = f2fs_post_read_required(inode) ? 1 : 0,
 		.io_type = io_type,
 		.io_wbc = wbc,
 		.bio = bio,
@@ -2752,14 +2817,15 @@
 
 	trace_f2fs_writepage(page, DATA);
 
-	/* we should bypass data pages to proceed the kworkder jobs */
+	/* we should bypass data pages to proceed the kworker jobs */
 	if (unlikely(f2fs_cp_error(sbi))) {
 		mapping_set_error(page->mapping, -EIO);
 		/*
 		 * don't drop any dirty dentry pages for keeping lastest
 		 * directory structure.
 		 */
-		if (S_ISDIR(inode->i_mode))
+		if (S_ISDIR(inode->i_mode) &&
+				!is_sbi_flag_set(sbi, SBI_IS_CLOSE))
 			goto redirty_out;
 		goto out;
 	}
@@ -2826,6 +2892,7 @@
 	if (err == -EAGAIN) {
 		err = f2fs_do_write_data_page(&fio);
 		if (err == -EAGAIN) {
+			f2fs_bug_on(sbi, compr_blocks);
 			fio.need_lock = LOCK_REQ;
 			err = f2fs_do_write_data_page(&fio);
 		}
@@ -2859,24 +2926,25 @@
 	}
 	unlock_page(page);
 	if (!S_ISDIR(inode->i_mode) && !IS_NOQUOTA(inode) &&
-			!F2FS_I(inode)->cp_task && allow_balance)
+			!F2FS_I(inode)->wb_task && allow_balance)
 		f2fs_balance_fs(sbi, need_balance_fs);
 
 	if (unlikely(f2fs_cp_error(sbi))) {
 		f2fs_submit_merged_write(sbi, DATA);
-		f2fs_submit_merged_ipu_write(sbi, bio, NULL);
+		if (bio && *bio)
+			f2fs_submit_merged_ipu_write(sbi, bio, NULL);
 		submitted = NULL;
 	}
 
 	if (submitted)
-		*submitted = fio.submitted ? 1 : 0;
+		*submitted = fio.submitted;
 
 	return 0;
 
 redirty_out:
 	redirty_page_for_writepage(wbc, page);
 	/*
-	 * pageout() in MM traslates EAGAIN, so calls handle_write_error()
+	 * pageout() in MM translates EAGAIN, so calls handle_write_error()
 	 * -> mapping_set_error() -> set_bit(AS_EIO, ...).
 	 * file_write_and_wait_range() will see EIO error, which is critical
 	 * to return value of fsync() followed by atomic_write failure to user.
@@ -2910,7 +2978,7 @@
 }
 
 /*
- * This function was copied from write_cche_pages from mm/page-writeback.c.
+ * This function was copied from write_cache_pages from mm/page-writeback.c.
  * The major change is making write step of cold data page separately from
  * warm/hot data page.
  */
@@ -3095,8 +3163,7 @@
 				} else if (ret == -EAGAIN) {
 					ret = 0;
 					if (wbc->sync_mode == WB_SYNC_ALL) {
-						cond_resched();
-						congestion_wait(BLK_RW_ASYNC,
+						f2fs_io_schedule_timeout(
 							DEFAULT_IO_TIMEOUT);
 						goto retry_write;
 					}
@@ -3157,7 +3224,7 @@
 					struct writeback_control *wbc)
 {
 	/* to avoid deadlock in path of data flush */
-	if (F2FS_I(inode)->cp_task)
+	if (F2FS_I(inode)->wb_task)
 		return false;
 
 	if (!S_ISREG(inode->i_mode))
@@ -3202,8 +3269,8 @@
 			f2fs_available_free_memory(sbi, DIRTY_DENTS))
 		goto skip_write;
 
-	/* skip writing during file defragment */
-	if (is_inode_flag_set(inode, FI_DO_DEFRAG))
+	/* skip writing in file defragment preparing stage */
+	if (is_inode_flag_set(inode, FI_SKIP_WRITES))
 		goto skip_write;
 
 	trace_f2fs_writepages(mapping->host, wbc, DATA);
@@ -3211,8 +3278,12 @@
 	/* to avoid spliting IOs due to mixed WB_SYNC_ALL and WB_SYNC_NONE */
 	if (wbc->sync_mode == WB_SYNC_ALL)
 		atomic_inc(&sbi->wb_sync_req[DATA]);
-	else if (atomic_read(&sbi->wb_sync_req[DATA]))
+	else if (atomic_read(&sbi->wb_sync_req[DATA])) {
+		/* to avoid potential deadlock */
+		if (current->plug)
+			blk_finish_plug(current->plug);
 		goto skip_write;
+	}
 
 	if (__should_serialize_io(inode, wbc)) {
 		mutex_lock(&sbi->writepages);
@@ -3403,7 +3474,7 @@
 
 		*fsdata = NULL;
 
-		if (len == PAGE_SIZE)
+		if (len == PAGE_SIZE && !(f2fs_is_atomic_file(inode)))
 			goto repeat;
 
 		ret = f2fs_prepare_compress_overwrite(inode, pagep,
@@ -3933,6 +4004,7 @@
 	filemap_invalidate_lock(inode->i_mapping);
 
 	set_inode_flag(inode, FI_ALIGNED_WRITE);
+	set_inode_flag(inode, FI_OPU_WRITE);
 
 	for (; secidx < end_sec; secidx++) {
 		down_write(&sbi->pin_sem);
@@ -3941,7 +4013,7 @@
 		f2fs_allocate_new_section(sbi, CURSEG_COLD_DATA_PINNED, false);
 		f2fs_unlock_op(sbi);
 
-		set_inode_flag(inode, FI_DO_DEFRAG);
+		set_inode_flag(inode, FI_SKIP_WRITES);
 
 		for (blkofs = 0; blkofs < blk_per_sec; blkofs++) {
 			struct page *page;
@@ -3958,7 +4030,7 @@
 			f2fs_put_page(page, 1);
 		}
 
-		clear_inode_flag(inode, FI_DO_DEFRAG);
+		clear_inode_flag(inode, FI_SKIP_WRITES);
 
 		ret = filemap_fdatawrite(inode->i_mapping);
 
@@ -3969,7 +4041,8 @@
 	}
 
 done:
-	clear_inode_flag(inode, FI_DO_DEFRAG);
+	clear_inode_flag(inode, FI_SKIP_WRITES);
+	clear_inode_flag(inode, FI_OPU_WRITE);
 	clear_inode_flag(inode, FI_ALIGNED_WRITE);
 
 	filemap_invalidate_unlock(inode->i_mapping);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/debug.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/debug.c
@@ -21,7 +21,7 @@
 #include "gc.h"
 
 static LIST_HEAD(f2fs_stat_list);
-static DEFINE_MUTEX(f2fs_stat_mutex);
+static DEFINE_RAW_SPINLOCK(f2fs_stat_lock);
 #ifdef CONFIG_DEBUG_FS
 static struct dentry *f2fs_debugfs_root;
 #endif
@@ -338,14 +338,16 @@
 	[SBI_QUOTA_SKIP_FLUSH]	= " quota_skip_flush",
 	[SBI_QUOTA_NEED_REPAIR]	= " quota_need_repair",
 	[SBI_IS_RESIZEFS]	= " resizefs",
+	[SBI_IS_FREEZING]	= " freezefs",
 };
 
 static int stat_show(struct seq_file *s, void *v)
 {
 	struct f2fs_stat_info *si;
 	int i = 0, j = 0;
+	unsigned long flags;
 
-	mutex_lock(&f2fs_stat_mutex);
+	raw_spin_lock_irqsave(&f2fs_stat_lock, flags);
 	list_for_each_entry(si, &f2fs_stat_list, stat_list) {
 		update_general_status(si->sbi);
 
@@ -573,7 +575,7 @@
 		seq_printf(s, "  - paged : %llu KB\n",
 				si->page_mem >> 10);
 	}
-	mutex_unlock(&f2fs_stat_mutex);
+	raw_spin_unlock_irqrestore(&f2fs_stat_lock, flags);
 	return 0;
 }
 
@@ -584,6 +586,7 @@
 {
 	struct f2fs_super_block *raw_super = F2FS_RAW_SUPER(sbi);
 	struct f2fs_stat_info *si;
+	unsigned long flags;
 	int i;
 
 	si = f2fs_kzalloc(sbi, sizeof(struct f2fs_stat_info), GFP_KERNEL);
@@ -619,9 +622,9 @@
 	atomic_set(&sbi->max_aw_cnt, 0);
 	atomic_set(&sbi->max_vw_cnt, 0);
 
-	mutex_lock(&f2fs_stat_mutex);
+	raw_spin_lock_irqsave(&f2fs_stat_lock, flags);
 	list_add_tail(&si->stat_list, &f2fs_stat_list);
-	mutex_unlock(&f2fs_stat_mutex);
+	raw_spin_unlock_irqrestore(&f2fs_stat_lock, flags);
 
 	return 0;
 }
@@ -629,10 +632,11 @@
 void f2fs_destroy_stats(struct f2fs_sb_info *sbi)
 {
 	struct f2fs_stat_info *si = F2FS_STAT(sbi);
+	unsigned long flags;
 
-	mutex_lock(&f2fs_stat_mutex);
+	raw_spin_lock_irqsave(&f2fs_stat_lock, flags);
 	list_del(&si->stat_list);
-	mutex_unlock(&f2fs_stat_mutex);
+	raw_spin_unlock_irqrestore(&f2fs_stat_lock, flags);
 
 	kfree(si);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/dir.c
@@ -82,7 +82,8 @@
 #ifdef CONFIG_UNICODE
 	struct super_block *sb = dir->i_sb;
 
-	if (IS_CASEFOLDED(dir)) {
+	if (IS_CASEFOLDED(dir) &&
+	    !is_dot_dotdot(fname->usr_fname->name, fname->usr_fname->len)) {
 		fname->cf_name.name = f2fs_kmem_cache_alloc(f2fs_cf_name_slab,
 					GFP_NOFS, false, F2FS_SB(sb));
 		if (!fname->cf_name.name)
@@ -189,7 +190,8 @@
 	unsigned long bidx = 0;
 
 	for (i = 0; i < level; i++)
-		bidx += dir_buckets(i, dir_level) * bucket_blocks(i);
+		bidx += mul_u32_u32(dir_buckets(i, dir_level),
+				    bucket_blocks(i));
 	bidx += idx * bucket_blocks(level);
 	return bidx;
 }
@@ -197,7 +199,8 @@
 static struct f2fs_dir_entry *find_in_block(struct inode *dir,
 				struct page *dentry_page,
 				const struct f2fs_filename *fname,
-				int *max_slots)
+				int *max_slots,
+				bool use_hash)
 {
 	struct f2fs_dentry_block *dentry_blk;
 	struct f2fs_dentry_ptr d;
@@ -205,7 +208,7 @@
 	dentry_blk = (struct f2fs_dentry_block *)page_address(dentry_page);
 
 	make_dentry_ptr_block(dir, &d, dentry_blk);
-	return f2fs_find_target_dentry(&d, fname, max_slots);
+	return f2fs_find_target_dentry(&d, fname, max_slots, use_hash);
 }
 
 #ifdef CONFIG_UNICODE
@@ -282,7 +285,8 @@
 }
 
 struct f2fs_dir_entry *f2fs_find_target_dentry(const struct f2fs_dentry_ptr *d,
-			const struct f2fs_filename *fname, int *max_slots)
+			const struct f2fs_filename *fname, int *max_slots,
+			bool use_hash)
 {
 	struct f2fs_dir_entry *de;
 	unsigned long bit_pos = 0;
@@ -305,7 +309,7 @@
 			continue;
 		}
 
-		if (de->hash_code == fname->hash) {
+		if (!use_hash || de->hash_code == fname->hash) {
 			res = f2fs_match_name(d->inode, fname,
 					      d->filename[bit_pos],
 					      le16_to_cpu(de->name_len));
@@ -332,11 +336,12 @@
 static struct f2fs_dir_entry *find_in_level(struct inode *dir,
 					unsigned int level,
 					const struct f2fs_filename *fname,
-					struct page **res_page)
+					struct page **res_page,
+					bool use_hash)
 {
 	int s = GET_DENTRY_SLOTS(fname->disk_name.len);
 	unsigned int nbucket, nblock;
-	unsigned int bidx, end_block;
+	unsigned int bidx, end_block, bucket_no;
 	struct page *dentry_page;
 	struct f2fs_dir_entry *de = NULL;
 	bool room = false;
@@ -345,8 +350,11 @@
 	nbucket = dir_buckets(level, F2FS_I(dir)->i_dir_level);
 	nblock = bucket_blocks(level);
 
+	bucket_no = use_hash ? le32_to_cpu(fname->hash) % nbucket : 0;
+
+start_find_bucket:
 	bidx = dir_block_index(level, F2FS_I(dir)->i_dir_level,
-			       le32_to_cpu(fname->hash) % nbucket);
+			       bucket_no);
 	end_block = bidx + nblock;
 
 	for (; bidx < end_block; bidx++) {
@@ -362,7 +370,7 @@
 			}
 		}
 
-		de = find_in_block(dir, dentry_page, fname, &max_slots);
+		de = find_in_block(dir, dentry_page, fname, &max_slots, use_hash);
 		if (IS_ERR(de)) {
 			*res_page = ERR_CAST(de);
 			de = NULL;
@@ -377,12 +385,18 @@
 		f2fs_put_page(dentry_page, 0);
 	}
 
-	if (!de && room && F2FS_I(dir)->chash != fname->hash) {
-		F2FS_I(dir)->chash = fname->hash;
-		F2FS_I(dir)->clevel = level;
-	}
+	if (de)
+		return de;
 
-	return de;
+	if (likely(use_hash)) {
+		if (room && F2FS_I(dir)->chash != fname->hash) {
+			F2FS_I(dir)->chash = fname->hash;
+			F2FS_I(dir)->clevel = level;
+		}
+	} else if (++bucket_no < nbucket) {
+		goto start_find_bucket;
+	}
+	return NULL;
 }
 
 struct f2fs_dir_entry *__f2fs_find_entry(struct inode *dir,
@@ -393,11 +407,15 @@
 	struct f2fs_dir_entry *de = NULL;
 	unsigned int max_depth;
 	unsigned int level;
+	bool use_hash = true;
 
 	*res_page = NULL;
 
+#if IS_ENABLED(CONFIG_UNICODE)
+start_find_entry:
+#endif
 	if (f2fs_has_inline_dentry(dir)) {
-		de = f2fs_find_in_inline_dir(dir, fname, res_page);
+		de = f2fs_find_in_inline_dir(dir, fname, res_page, use_hash);
 		goto out;
 	}
 
@@ -413,11 +431,18 @@
 	}
 
 	for (level = 0; level < max_depth; level++) {
-		de = find_in_level(dir, level, fname, res_page);
+		de = find_in_level(dir, level, fname, res_page, use_hash);
 		if (de || IS_ERR(*res_page))
 			break;
 	}
+
 out:
+#if IS_ENABLED(CONFIG_UNICODE)
+	if (IS_CASEFOLDED(dir) && !de && use_hash) {
+		use_hash = false;
+		goto start_find_entry;
+	}
+#endif
 	/* This is to increase the speed of f2fs_create */
 	if (!de)
 		F2FS_I(dir)->task = current;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/extent_cache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/extent_cache.c
@@ -112,7 +112,7 @@
  * @prev_ex: extent before ofs
  * @next_ex: extent after ofs
  * @insert_p: insert point for new extent at ofs
- * in order to simpfy the insertion after.
+ * in order to simplify the insertion after.
  * tree must stay unchanged between lookup and insertion.
  */
 struct rb_entry *f2fs_lookup_rb_tree_ret(struct rb_root_cached *root,
@@ -415,7 +415,8 @@
 	struct extent_node *en;
 	bool ret = false;
 
-	f2fs_bug_on(sbi, !et);
+	if (!et)
+		return false;
 
 	trace_f2fs_lookup_extent_tree_start(inode, pgofs);
 
@@ -572,7 +573,7 @@
 	if (!en)
 		en = next_en;
 
-	/* 2. invlidate all extent nodes in range [fofs, fofs + len - 1] */
+	/* 2. invalidate all extent nodes in range [fofs, fofs + len - 1] */
 	while (en && en->ei.fofs < end) {
 		unsigned int org_end;
 		int parts = 0;	/* # of parts current extent split into */
@@ -804,9 +805,8 @@
 	if (!f2fs_may_extent_tree(inode))
 		return;
 
-	set_inode_flag(inode, FI_NO_EXTENT);
-
 	write_lock(&et->lock);
+	set_inode_flag(inode, FI_NO_EXTENT);
 	__free_extent_tree(sbi, et);
 	if (et->largest.len) {
 		et->largest.len = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/f2fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/f2fs.h
@@ -55,6 +55,7 @@
 	FAULT_DISCARD,
 	FAULT_WRITE_IO,
 	FAULT_SLAB_ALLOC,
+	FAULT_DQUOT_INIT,
 	FAULT_MAX,
 };
 
@@ -63,7 +64,7 @@
 
 struct f2fs_fault_info {
 	atomic_t inject_ops;
-	unsigned int inject_rate;
+	int inject_rate;
 	unsigned int inject_type;
 };
 
@@ -248,6 +249,10 @@
 					 * condition of read on truncated area
 					 * by extent_cache
 					 */
+	DATA_GENERIC_ENHANCE_UPDATE,	/*
+					 * strong check on range and segment
+					 * bitmap for update case
+					 */
 	META_GENERIC,
 };
 
@@ -256,7 +261,8 @@
 	ORPHAN_INO,		/* for orphan ino list */
 	APPEND_INO,		/* for append ino list */
 	UPDATE_INO,		/* for update ino list */
-	TRANS_DIR_INO,		/* for trasactions dir ino list */
+	TRANS_DIR_INO,		/* for transactions dir ino list */
+	XATTR_DIR_INO,		/* for xattr updated dir ino list */
 	FLUSH_INO,		/* for multiple device flushing */
 	MAX_INO_ENTRY,		/* max. list */
 };
@@ -487,11 +493,11 @@
 #ifdef CONFIG_UNICODE
 	/*
 	 * For casefolded directories: the casefolded name, but it's left NULL
-	 * if the original name is not valid Unicode, if the directory is both
-	 * casefolded and encrypted and its encryption key is unavailable, or if
-	 * the filesystem is doing an internal operation where usr_fname is also
-	 * NULL.  In all these cases we fall back to treating the name as an
-	 * opaque byte sequence.
+	 * if the original name is not valid Unicode, if the original name is
+	 * "." or "..", if the directory is both casefolded and encrypted and
+	 * its encryption key is unavailable, or if the filesystem is doing an
+	 * internal operation where usr_fname is also NULL.  In all these cases
+	 * we fall back to treating the name as an opaque byte sequence.
 	 */
 	struct fscrypt_str cf_name;
 #endif
@@ -617,6 +623,7 @@
 				F2FS_MAP_UNWRITTEN)
 
 struct f2fs_map_blocks {
+	struct block_device *m_bdev;	/* for multi-device dio */
 	block_t m_pblk;
 	block_t m_lblk;
 	unsigned int m_len;
@@ -625,6 +632,7 @@
 	pgoff_t *m_next_extent;		/* point to next possible extent */
 	int m_seg_type;
 	bool m_may_create;		/* indicate it is from write path */
+	bool m_multidev_dio;		/* indicate it allows multi-device dio */
 };
 
 /* for flag in get_data_block */
@@ -706,8 +714,8 @@
 	FI_FIRST_BLOCK_WRITTEN,	/* indicate #0 data block was written */
 	FI_DROP_CACHE,		/* drop dirty page cache */
 	FI_DATA_EXIST,		/* indicate data exists */
-	FI_INLINE_DOTS,		/* indicate inline dot dentries */
-	FI_DO_DEFRAG,		/* indicate defragment is running */
+	FI_SKIP_WRITES,		/* should skip data page writeback */
+	FI_OPU_WRITE,		/* used for opu per file */
 	FI_DIRTY_FILE,		/* indicate regular/symlink has dirty pages */
 	FI_NO_PREALLOC,		/* indicate skipped preallocated blocks */
 	FI_HOT_DATA,		/* indicate file is hot */
@@ -744,6 +752,7 @@
 	unsigned int clevel;		/* maximum level of given file name */
 	struct task_struct *task;	/* lookup and create consistency */
 	struct task_struct *cp_task;	/* separate cp/wb IO stats*/
+	struct task_struct *wb_task;	/* indicate inode is in context of writeback */
 	nid_t i_xattr_nid;		/* node id that contains xattrs */
 	loff_t	last_disk_size;		/* lastly written file size */
 	spinlock_t i_size_lock;		/* protect last_disk_size */
@@ -1012,6 +1021,7 @@
 	unsigned int segment_count;	/* total # of segments */
 	unsigned int main_segments;	/* # of segments in main area */
 	unsigned int reserved_segments;	/* # of reserved segments */
+	unsigned int additional_reserved_segments;/* reserved segs for IO align feature */
 	unsigned int ovp_segments;	/* # of overprovision segments */
 
 	/* a threshold to reclaim prefree segments */
@@ -1077,8 +1087,8 @@
  */
 #define PAGE_TYPE_OF_BIO(type)	((type) > META ? META : (type))
 enum page_type {
-	DATA,
-	NODE,
+	DATA = 0,
+	NODE = 1,	/* should not change this */
 	META,
 	NR_PAGE_TYPE,
 	META_FLUSH,
@@ -1115,6 +1125,7 @@
 	CP_FASTBOOT_MODE,
 	CP_SPEC_LOG_NUM,
 	CP_RECOVER_DIR,
+	CP_XATTR_DIR,
 };
 
 enum iostat_type {
@@ -1161,18 +1172,19 @@
 	struct page *encrypted_page;	/* encrypted page */
 	struct page *compressed_page;	/* compressed page */
 	struct list_head list;		/* serialize IOs */
-	bool submitted;		/* indicate IO submission */
-	int need_lock;		/* indicate we need to lock cp_rwsem */
-	bool in_list;		/* indicate fio is in io_list */
-	bool is_por;		/* indicate IO is from recovery or not */
-	bool retry;		/* need to reallocate block address */
-	int compr_blocks;	/* # of compressed block addresses */
-	bool encrypted;		/* indicate file is encrypted */
+	unsigned int compr_blocks;	/* # of compressed block addresses */
+	unsigned int need_lock:8;	/* indicate we need to lock cp_rwsem */
+	unsigned int version:8;		/* version of the node */
+	unsigned int submitted:1;	/* indicate IO submission */
+	unsigned int in_list:1;		/* indicate fio is in io_list */
+	unsigned int is_por:1;		/* indicate IO is from recovery or not */
+	unsigned int retry:1;		/* need to reallocate block address */
+	unsigned int encrypted:1;	/* indicate file is encrypted */
+	unsigned int post_read:1;	/* require post read */
 	enum iostat_type io_type;	/* io type */
 	struct writeback_control *io_wbc; /* writeback control */
 	struct bio **bio;		/* bio for ipu */
 	sector_t *last_block;		/* last block number in bio */
-	unsigned char version;		/* version of the node */
 };
 
 struct bio_entry {
@@ -1204,7 +1216,6 @@
 #ifdef CONFIG_BLK_DEV_ZONED
 	unsigned int nr_blkz;		/* Total number of zones */
 	unsigned long *blkz_seq;	/* Bitmap indicating sequential zones */
-	block_t *zone_capacity_blocks;  /* Array of zone capacity in blks */
 #endif
 };
 
@@ -1252,6 +1263,7 @@
 	SBI_QUOTA_SKIP_FLUSH,			/* skip flushing quota in current CP */
 	SBI_QUOTA_NEED_REPAIR,			/* quota file may be corrupted */
 	SBI_IS_RESIZEFS,			/* resizefs is in process */
+	SBI_IS_FREEZING,			/* freezefs is in process */
 };
 
 enum {
@@ -1624,6 +1636,7 @@
 	unsigned int meta_ino_num;		/* meta inode number*/
 	unsigned int log_blocks_per_seg;	/* log2 blocks per segment */
 	unsigned int blocks_per_seg;		/* blocks per segment */
+	unsigned int unusable_blocks_per_sec;	/* unusable blocks per section */
 	unsigned int segs_per_sec;		/* segments per section */
 	unsigned int secs_per_zone;		/* sections per zone */
 	unsigned int total_sections;		/* total section count */
@@ -1728,12 +1741,15 @@
 
 	/* For shrinker support */
 	struct list_head s_list;
+	struct mutex umount_mutex;
+	unsigned int shrinker_run_no;
+
+	/* For multi devices */
 	int s_ndevs;				/* number of devices */
 	struct f2fs_dev_info *devs;		/* for device list */
 	unsigned int dirty_device;		/* for checkpoint data flush */
 	spinlock_t dev_lock;			/* protect dirty_device */
-	struct mutex umount_mutex;
-	unsigned int shrinker_run_no;
+	bool aligned_blksize;			/* all devices has the same logical blksize */
 
 	/* For write statistics */
 	u64 sectors_written_start;
@@ -2184,6 +2200,11 @@
 
 	if (!__allow_reserved_blocks(sbi, inode, true))
 		avail_user_block_count -= F2FS_OPTION(sbi).root_reserved_blocks;
+
+	if (F2FS_IO_ALIGNED(sbi))
+		avail_user_block_count -= sbi->blocks_per_seg *
+				SM_I(sbi)->additional_reserved_segments;
+
 	if (unlikely(is_sbi_flag_set(sbi, SBI_CP_DISABLED))) {
 		if (avail_user_block_count > sbi->unusable_block_count)
 			avail_user_block_count -= sbi->unusable_block_count;
@@ -2430,6 +2451,11 @@
 
 	if (!__allow_reserved_blocks(sbi, inode, false))
 		valid_block_count += F2FS_OPTION(sbi).root_reserved_blocks;
+
+	if (F2FS_IO_ALIGNED(sbi))
+		valid_block_count += sbi->blocks_per_seg *
+				SM_I(sbi)->additional_reserved_segments;
+
 	user_block_count = sbi->user_block_count;
 	if (unlikely(is_sbi_flag_set(sbi, SBI_CP_DISABLED)))
 		user_block_count -= sbi->unusable_block_count;
@@ -2474,11 +2500,17 @@
 {
 	spin_lock(&sbi->stat_lock);
 
-	f2fs_bug_on(sbi, !sbi->total_valid_block_count);
-	f2fs_bug_on(sbi, !sbi->total_valid_node_count);
+	if (unlikely(!sbi->total_valid_block_count ||
+			!sbi->total_valid_node_count)) {
+		f2fs_warn(sbi, "dec_valid_node_count: inconsistent block counts, total_valid_block:%u, total_valid_node:%u",
+			  sbi->total_valid_block_count,
+			  sbi->total_valid_node_count);
+		set_sbi_flag(sbi, SBI_NEED_FSCK);
+	} else {
+		sbi->total_valid_block_count--;
+		sbi->total_valid_node_count--;
+	}
 
-	sbi->total_valid_node_count--;
-	sbi->total_valid_block_count--;
 	if (sbi->reserved_blocks &&
 		sbi->current_reserved_blocks < sbi->reserved_blocks)
 		sbi->current_reserved_blocks++;
@@ -2557,16 +2589,6 @@
 	return pagecache_get_page(mapping, index, fgp_flags, gfp_mask);
 }
 
-static inline void f2fs_copy_page(struct page *src, struct page *dst)
-{
-	char *src_kaddr = kmap(src);
-	char *dst_kaddr = kmap(dst);
-
-	memcpy(dst_kaddr, src_kaddr, PAGE_SIZE);
-	kunmap(dst);
-	kunmap(src);
-}
-
 static inline void f2fs_put_page(struct page *page, int unlock)
 {
 	if (!page)
@@ -2818,7 +2840,6 @@
 			return;
 		fallthrough;
 	case FI_DATA_EXIST:
-	case FI_INLINE_DOTS:
 	case FI_PIN_FILE:
 	case FI_COMPRESS_RELEASED:
 		f2fs_mark_inode_dirty_sync(inode, true);
@@ -2936,8 +2957,6 @@
 		set_bit(FI_INLINE_DENTRY, fi->flags);
 	if (ri->i_inline & F2FS_DATA_EXIST)
 		set_bit(FI_DATA_EXIST, fi->flags);
-	if (ri->i_inline & F2FS_INLINE_DOTS)
-		set_bit(FI_INLINE_DOTS, fi->flags);
 	if (ri->i_inline & F2FS_EXTRA_ATTR)
 		set_bit(FI_EXTRA_ATTR, fi->flags);
 	if (ri->i_inline & F2FS_PIN_FILE)
@@ -2958,8 +2977,6 @@
 		ri->i_inline |= F2FS_INLINE_DENTRY;
 	if (is_inode_flag_set(inode, FI_DATA_EXIST))
 		ri->i_inline |= F2FS_DATA_EXIST;
-	if (is_inode_flag_set(inode, FI_INLINE_DOTS))
-		ri->i_inline |= F2FS_INLINE_DOTS;
 	if (is_inode_flag_set(inode, FI_EXTRA_ATTR))
 		ri->i_inline |= F2FS_EXTRA_ATTR;
 	if (is_inode_flag_set(inode, FI_PIN_FILE))
@@ -3042,11 +3059,6 @@
 	return is_inode_flag_set(inode, FI_DATA_EXIST);
 }
 
-static inline int f2fs_has_inline_dots(struct inode *inode)
-{
-	return is_inode_flag_set(inode, FI_INLINE_DOTS);
-}
-
 static inline int f2fs_is_mmap_file(struct inode *inode)
 {
 	return is_inode_flag_set(inode, FI_MMAP_FILE);
@@ -3313,7 +3325,8 @@
 			struct f2fs_filename *fname);
 void f2fs_free_filename(struct f2fs_filename *fname);
 struct f2fs_dir_entry *f2fs_find_target_dentry(const struct f2fs_dentry_ptr *d,
-			const struct f2fs_filename *fname, int *max_slots);
+			const struct f2fs_filename *fname, int *max_slots,
+			bool use_hash);
 int f2fs_fill_dentries(struct dir_context *ctx, struct f2fs_dentry_ptr *d,
 			unsigned int start_pos, struct fscrypt_str *fstr);
 void f2fs_do_make_empty_dir(struct inode *inode, struct inode *parent,
@@ -3363,6 +3376,7 @@
  */
 int f2fs_inode_dirtied(struct inode *inode, bool sync);
 void f2fs_inode_synced(struct inode *inode);
+int f2fs_dquot_initialize(struct inode *inode);
 int f2fs_enable_quota_files(struct f2fs_sb_info *sbi, bool rdonly);
 int f2fs_quota_sync(struct super_block *sb, int type);
 loff_t max_file_blocks(struct inode *inode);
@@ -3391,7 +3405,7 @@
 bool f2fs_is_checkpointed_node(struct f2fs_sb_info *sbi, nid_t nid);
 bool f2fs_need_inode_block_update(struct f2fs_sb_info *sbi, nid_t ino);
 int f2fs_get_node_info(struct f2fs_sb_info *sbi, nid_t nid,
-						struct node_info *ni);
+				struct node_info *ni, bool checkpoint_context);
 pgoff_t f2fs_get_next_page_offset(struct dnode_of_data *dn, pgoff_t pgofs);
 int f2fs_get_dnode_of_data(struct dnode_of_data *dn, pgoff_t index, int mode);
 int f2fs_truncate_inode_blocks(struct inode *inode, pgoff_t from);
@@ -3492,6 +3506,8 @@
 			block_t old_blkaddr, block_t *new_blkaddr,
 			struct f2fs_summary *sum, int type,
 			struct f2fs_io_info *fio);
+void f2fs_update_device_state(struct f2fs_sb_info *sbi, nid_t ino,
+					block_t blkaddr, unsigned int blkcnt);
 void f2fs_wait_on_page_writeback(struct page *page,
 			enum page_type type, bool ordered, bool locked);
 void f2fs_wait_on_block_writeback(struct inode *inode, block_t blkaddr);
@@ -3520,6 +3536,7 @@
  * checkpoint.c
  */
 void f2fs_stop_checkpoint(struct f2fs_sb_info *sbi, bool end_io);
+void f2fs_flush_ckpt_thread(struct f2fs_sb_info *sbi);
 struct page *f2fs_grab_meta_page(struct f2fs_sb_info *sbi, pgoff_t index);
 struct page *f2fs_get_meta_page(struct f2fs_sb_info *sbi, pgoff_t index);
 struct page *f2fs_get_meta_page_retry(struct f2fs_sb_info *sbi, pgoff_t index);
@@ -3548,7 +3565,8 @@
 int f2fs_get_valid_checkpoint(struct f2fs_sb_info *sbi);
 void f2fs_update_dirty_page(struct inode *inode, struct page *page);
 void f2fs_remove_dirty_inode(struct inode *inode);
-int f2fs_sync_dirty_inodes(struct f2fs_sb_info *sbi, enum inode_type type);
+int f2fs_sync_dirty_inodes(struct f2fs_sb_info *sbi, enum inode_type type,
+								bool from_cp);
 void f2fs_wait_on_all_pages(struct f2fs_sb_info *sbi, int type);
 u64 f2fs_get_sectors_written(struct f2fs_sb_info *sbi);
 int f2fs_write_checkpoint(struct f2fs_sb_info *sbi, struct cp_control *cpc);
@@ -3633,7 +3651,7 @@
 int f2fs_gc(struct f2fs_sb_info *sbi, bool sync, bool background, bool force,
 			unsigned int segno);
 void f2fs_build_gc_manager(struct f2fs_sb_info *sbi);
-int f2fs_resize_fs(struct f2fs_sb_info *sbi, __u64 block_count);
+int f2fs_resize_fs(struct file *filp, __u64 block_count);
 int __init f2fs_create_garbage_collection_cache(void);
 void f2fs_destroy_garbage_collection_cache(void);
 
@@ -3896,6 +3914,7 @@
  * inline.c
  */
 bool f2fs_may_inline_data(struct inode *inode);
+bool f2fs_sanity_check_inline_data(struct inode *inode);
 bool f2fs_may_inline_dentry(struct inode *inode);
 void f2fs_do_read_inline_data(struct page *page, struct page *ipage);
 void f2fs_truncate_inline_inode(struct inode *inode,
@@ -3908,7 +3927,8 @@
 int f2fs_recover_inline_data(struct inode *inode, struct page *npage);
 struct f2fs_dir_entry *f2fs_find_in_inline_dir(struct inode *dir,
 					const struct f2fs_filename *fname,
-					struct page **res_page);
+					struct page **res_page,
+					bool use_hash);
 int f2fs_make_empty_inline_dir(struct inode *inode, struct inode *parent,
 			struct page *ipage);
 int f2fs_add_inline_entry(struct inode *dir, const struct f2fs_filename *fname,
@@ -4152,8 +4172,7 @@
 
 	if (!f2fs_compressed_file(inode))
 		return true;
-	if (S_ISREG(inode->i_mode) &&
-		(get_dirty_pages(inode) || atomic_read(&fi->i_compr_blocks)))
+	if (S_ISREG(inode->i_mode) && F2FS_HAS_BLOCKS(inode))
 		return false;
 
 	fi->i_flags &= ~F2FS_COMPR_FL;
@@ -4257,6 +4276,11 @@
 	return false;
 }
 
+static inline bool f2fs_dev_is_readonly(struct f2fs_sb_info *sbi)
+{
+	return f2fs_sb_has_readonly(sbi) || f2fs_hw_is_readonly(sbi);
+}
+
 static inline bool f2fs_lfs_mode(struct f2fs_sb_info *sbi)
 {
 	return F2FS_OPTION(sbi).fs_mode == FS_MODE_LFS;
@@ -4302,6 +4326,16 @@
 	return align & blocksize_mask;
 }
 
+static inline bool f2fs_allow_multi_device_dio(struct f2fs_sb_info *sbi,
+								int flag)
+{
+	if (!f2fs_is_multi_device(sbi))
+		return false;
+	if (flag != F2FS_GET_BLOCK_DIO)
+		return false;
+	return sbi->aligned_blksize;
+}
+
 static inline bool f2fs_force_buffered_io(struct inode *inode,
 				struct kiocb *iocb, struct iov_iter *iter)
 {
@@ -4310,7 +4344,9 @@
 
 	if (f2fs_post_read_required(inode))
 		return true;
-	if (f2fs_is_multi_device(sbi))
+
+	/* disallow direct IO if any of devices has unaligned blksize */
+	if (f2fs_is_multi_device(sbi) && !sbi->aligned_blksize)
 		return true;
 	/*
 	 * for blkzoned device, fallback direct IO to buffered IO, so
@@ -4337,10 +4373,14 @@
 }
 
 #ifdef CONFIG_F2FS_FAULT_INJECTION
-extern void f2fs_build_fault_attr(struct f2fs_sb_info *sbi, unsigned int rate,
-							unsigned int type);
+extern int f2fs_build_fault_attr(struct f2fs_sb_info *sbi, unsigned long rate,
+							unsigned long type);
 #else
-#define f2fs_build_fault_attr(sbi, rate, type)		do { } while (0)
+static inline int f2fs_build_fault_attr(struct f2fs_sb_info *sbi,
+					unsigned long rate, unsigned long type)
+{
+	return 0;
+}
 #endif
 
 static inline bool is_journalled_quota(struct f2fs_sb_info *sbi)
@@ -4361,6 +4401,12 @@
 	return F2FS_OPTION(sbi).discard_unit == DISCARD_UNIT_BLOCK;
 }
 
+static inline void f2fs_io_schedule_timeout(long timeout)
+{
+	set_current_state(TASK_UNINTERRUPTIBLE);
+	io_schedule_timeout(timeout);
+}
+
 #define EFSBADCRC	EBADMSG		/* Bad CRC detected */
 #define EFSCORRUPTED	EUCLEAN		/* Filesystem is corrupted */
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/file.c
@@ -41,7 +41,7 @@
 	vm_fault_t ret;
 
 	ret = filemap_fault(vmf);
-	if (!ret)
+	if (ret & VM_FAULT_LOCKED)
 		f2fs_update_iostat(F2FS_I_SB(inode), APP_MAPPED_READ_IO,
 							F2FS_BLKSIZE);
 
@@ -216,6 +216,9 @@
 		f2fs_exist_written_data(sbi, F2FS_I(inode)->i_pino,
 							TRANS_DIR_INO))
 		cp_reason = CP_RECOVER_DIR;
+	else if (f2fs_exist_written_data(sbi, F2FS_I(inode)->i_pino,
+							XATTR_DIR_INO))
+		cp_reason = CP_XATTR_DIR;
 
 	return cp_reason;
 }
@@ -304,7 +307,7 @@
 		 * for OPU case, during fsync(), node can be persisted before
 		 * data when lower device doesn't support write barrier, result
 		 * in data corruption after SPO.
-		 * So for strict fsync mode, force to use atomic write sematics
+		 * So for strict fsync mode, force to use atomic write semantics
 		 * to keep write order in between data/node and last node to
 		 * avoid potential data corruption.
 		 */
@@ -786,7 +789,7 @@
 		return -EIO;
 	}
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		return err;
 
@@ -899,9 +902,14 @@
 				  ATTR_GID | ATTR_TIMES_SET))))
 		return -EPERM;
 
-	if ((attr->ia_valid & ATTR_SIZE) &&
-		!f2fs_is_compress_backend_ready(inode))
-		return -EOPNOTSUPP;
+	if ((attr->ia_valid & ATTR_SIZE)) {
+		if (!f2fs_is_compress_backend_ready(inode))
+			return -EOPNOTSUPP;
+		if (is_inode_flag_set(inode, FI_COMPRESS_RELEASED) &&
+			!IS_ALIGNED(attr->ia_size,
+			F2FS_BLK_TO_BYTES(F2FS_I(inode)->i_cluster_size)))
+			return -EINVAL;
+	}
 
 	err = setattr_prepare(&init_user_ns, dentry, attr);
 	if (err)
@@ -916,7 +924,7 @@
 		return err;
 
 	if (is_quota_modification(inode, attr)) {
-		err = dquot_initialize(inode);
+		err = f2fs_dquot_initialize(inode);
 		if (err)
 			return err;
 	}
@@ -957,6 +965,13 @@
 				return err;
 		}
 
+		/*
+		 * wait for inflight dio, blocks should be removed after
+		 * IO completion.
+		 */
+		if (attr->ia_size < old_size)
+			inode_dio_wait(inode);
+
 		down_write(&F2FS_I(inode)->i_gc_rwsem[WRITE]);
 		filemap_invalidate_lock(inode->i_mapping);
 
@@ -1232,7 +1247,7 @@
 			if (ret)
 				return ret;
 
-			ret = f2fs_get_node_info(sbi, dn.nid, &ni);
+			ret = f2fs_get_node_info(sbi, dn.nid, &ni, false);
 			if (ret) {
 				f2fs_put_dnode(&dn);
 				return ret;
@@ -1276,8 +1291,12 @@
 				f2fs_put_page(psrc, 1);
 				return PTR_ERR(pdst);
 			}
-			f2fs_copy_page(psrc, pdst);
+
+			f2fs_wait_on_page_writeback(pdst, DATA, true, true);
+
+			memcpy_page(pdst, 0, psrc, 0, PAGE_SIZE);
 			set_page_dirty(pdst);
+			set_page_private_gcing(pdst);
 			f2fs_put_page(pdst, 1);
 			f2fs_put_page(psrc, 1);
 
@@ -1436,11 +1455,19 @@
 			ret = -ENOSPC;
 			break;
 		}
-		if (dn->data_blkaddr != NEW_ADDR) {
-			f2fs_invalidate_blocks(sbi, dn->data_blkaddr);
-			dn->data_blkaddr = NEW_ADDR;
-			f2fs_set_data_blkaddr(dn);
+
+		if (dn->data_blkaddr == NEW_ADDR)
+			continue;
+
+		if (!f2fs_is_valid_blkaddr(sbi, dn->data_blkaddr,
+					DATA_GENERIC_ENHANCE)) {
+			ret = -EFSCORRUPTED;
+			break;
 		}
+
+		f2fs_invalidate_blocks(sbi, dn->data_blkaddr);
+		dn->data_blkaddr = NEW_ADDR;
+		f2fs_set_data_blkaddr(dn);
 	}
 
 	f2fs_update_extent_cache_range(dn, start, 0, index - start);
@@ -1748,11 +1775,6 @@
 		(mode & (FALLOC_FL_COLLAPSE_RANGE | FALLOC_FL_INSERT_RANGE)))
 		return -EOPNOTSUPP;
 
-	if (f2fs_compressed_file(inode) &&
-		(mode & (FALLOC_FL_PUNCH_HOLE | FALLOC_FL_COLLAPSE_RANGE |
-			FALLOC_FL_ZERO_RANGE | FALLOC_FL_INSERT_RANGE)))
-		return -EOPNOTSUPP;
-
 	if (mode & ~(FALLOC_FL_KEEP_SIZE | FALLOC_FL_PUNCH_HOLE |
 			FALLOC_FL_COLLAPSE_RANGE | FALLOC_FL_ZERO_RANGE |
 			FALLOC_FL_INSERT_RANGE))
@@ -1760,6 +1782,27 @@
 
 	inode_lock(inode);
 
+	/*
+	 * Pinned file should not support partial truncation since the block
+	 * can be used by applications.
+	 */
+	if ((f2fs_compressed_file(inode) || f2fs_is_pinned_file(inode)) &&
+		(mode & (FALLOC_FL_PUNCH_HOLE | FALLOC_FL_COLLAPSE_RANGE |
+			FALLOC_FL_ZERO_RANGE | FALLOC_FL_INSERT_RANGE))) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	ret = file_modified(file);
+	if (ret)
+		goto out;
+
+	/*
+	 * wait for inflight dio, blocks should be removed after IO
+	 * completion.
+	 */
+	inode_dio_wait(inode);
+
 	if (mode & FALLOC_FL_PUNCH_HOLE) {
 		if (offset >= inode->i_size)
 			goto out;
@@ -1791,7 +1834,7 @@
 static int f2fs_release_file(struct inode *inode, struct file *filp)
 {
 	/*
-	 * f2fs_relase_file is called at every close calls. So we should
+	 * f2fs_release_file is called at every close calls. So we should
 	 * not drop any inmemory pages by close called by other process.
 	 */
 	if (!(filp->f_mode & FMODE_WRITE) ||
@@ -1857,10 +1900,7 @@
 		if (masked_flags & F2FS_COMPR_FL) {
 			if (!f2fs_disable_compressed_file(inode))
 				return -EINVAL;
-		}
-		if (iflags & F2FS_NOCOMP_FL)
-			return -EINVAL;
-		if (iflags & F2FS_COMPR_FL) {
+		} else {
 			if (!f2fs_may_compress(inode))
 				return -EINVAL;
 			if (S_ISREG(inode->i_mode) && inode->i_size)
@@ -1869,10 +1909,6 @@
 			set_compress_context(inode);
 		}
 	}
-	if ((iflags ^ masked_flags) & F2FS_NOCOMP_FL) {
-		if (masked_flags & F2FS_COMPR_FL)
-			return -EINVAL;
-	}
 
 	fi->i_flags = iflags | (fi->i_flags & ~mask);
 	f2fs_bug_on(F2FS_I_SB(inode), (fi->i_flags & F2FS_COMPR_FL) &&
@@ -1987,6 +2023,9 @@
 	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	int ret;
 
+	if (!(filp->f_mode & FMODE_WRITE))
+		return -EBADF;
+
 	if (!inode_owner_or_capable(&init_user_ns, inode))
 		return -EACCES;
 
@@ -2002,7 +2041,10 @@
 
 	inode_lock(inode);
 
-	f2fs_disable_compressed_file(inode);
+	if (!f2fs_disable_compressed_file(inode)) {
+		ret = -EINVAL;
+		goto out;
+	}
 
 	if (f2fs_is_atomic_file(inode)) {
 		if (is_inode_flag_set(inode, FI_ATOMIC_REVOKE_REQUEST))
@@ -2054,6 +2096,9 @@
 	struct inode *inode = file_inode(filp);
 	int ret;
 
+	if (!(filp->f_mode & FMODE_WRITE))
+		return -EBADF;
+
 	if (!inode_owner_or_capable(&init_user_ns, inode))
 		return -EACCES;
 
@@ -2096,6 +2141,9 @@
 	struct inode *inode = file_inode(filp);
 	int ret;
 
+	if (!(filp->f_mode & FMODE_WRITE))
+		return -EBADF;
+
 	if (!inode_owner_or_capable(&init_user_ns, inode))
 		return -EACCES;
 
@@ -2131,6 +2179,9 @@
 	struct inode *inode = file_inode(filp);
 	int ret;
 
+	if (!(filp->f_mode & FMODE_WRITE))
+		return -EBADF;
+
 	if (!inode_owner_or_capable(&init_user_ns, inode))
 		return -EACCES;
 
@@ -2160,6 +2211,9 @@
 	struct inode *inode = file_inode(filp);
 	int ret;
 
+	if (!(filp->f_mode & FMODE_WRITE))
+		return -EBADF;
+
 	if (!inode_owner_or_capable(&init_user_ns, inode))
 		return -EACCES;
 
@@ -2553,10 +2607,6 @@
 	bool fragmented = false;
 	int err;
 
-	/* if in-place-update policy is enabled, don't waste time here */
-	if (f2fs_should_update_inplace(inode, NULL))
-		return -EINVAL;
-
 	pg_start = range->start >> PAGE_SHIFT;
 	pg_end = (range->start + range->len) >> PAGE_SHIFT;
 
@@ -2564,6 +2614,13 @@
 
 	inode_lock(inode);
 
+	/* if in-place-update policy is enabled, don't waste time here */
+	set_inode_flag(inode, FI_OPU_WRITE);
+	if (f2fs_should_update_inplace(inode, NULL)) {
+		err = -EINVAL;
+		goto out;
+	}
+
 	/* writeback all dirty pages in the range */
 	err = filemap_write_and_wait_range(inode->i_mapping, range->start,
 						range->start + range->len - 1);
@@ -2645,7 +2702,7 @@
 			goto check;
 		}
 
-		set_inode_flag(inode, FI_DO_DEFRAG);
+		set_inode_flag(inode, FI_SKIP_WRITES);
 
 		idx = map.m_lblk;
 		while (idx < map.m_lblk + map.m_len && cnt < blk_per_seg) {
@@ -2657,7 +2714,10 @@
 				goto clear_out;
 			}
 
+			f2fs_wait_on_page_writeback(page, DATA, true, true);
+
 			set_page_dirty(page);
+			set_page_private_gcing(page);
 			f2fs_put_page(page, 1);
 
 			idx++;
@@ -2670,15 +2730,16 @@
 		if (map.m_lblk < pg_end && cnt < blk_per_seg)
 			goto do_map;
 
-		clear_inode_flag(inode, FI_DO_DEFRAG);
+		clear_inode_flag(inode, FI_SKIP_WRITES);
 
 		err = filemap_fdatawrite(inode->i_mapping);
 		if (err)
 			goto out;
 	}
 clear_out:
-	clear_inode_flag(inode, FI_DO_DEFRAG);
+	clear_inode_flag(inode, FI_SKIP_WRITES);
 out:
+	clear_inode_flag(inode, FI_OPU_WRITE);
 	inode_unlock(inode);
 	if (!err)
 		range->len = (u64)total << PAGE_SHIFT;
@@ -2771,6 +2832,12 @@
 			goto out;
 	}
 
+	if (f2fs_compressed_file(src) || f2fs_compressed_file(dst) ||
+		f2fs_is_pinned_file(src) || f2fs_is_pinned_file(dst)) {
+		ret = -EOPNOTSUPP;
+		goto out_unlock;
+	}
+
 	ret = -EINVAL;
 	if (pos_in + len > src->i_size || pos_in + len < pos_in)
 		goto out_unlock;
@@ -2968,15 +3035,16 @@
 	struct dquot *transfer_to[MAXQUOTAS] = {};
 	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	struct super_block *sb = sbi->sb;
-	int err = 0;
+	int err;
 
 	transfer_to[PRJQUOTA] = dqget(sb, make_kqid_projid(kprojid));
-	if (!IS_ERR(transfer_to[PRJQUOTA])) {
-		err = __dquot_transfer(inode, transfer_to);
-		if (err)
-			set_sbi_flag(sbi, SBI_QUOTA_NEED_REPAIR);
-		dqput(transfer_to[PRJQUOTA]);
-	}
+	if (IS_ERR(transfer_to[PRJQUOTA]))
+		return PTR_ERR(transfer_to[PRJQUOTA]);
+
+	err = __dquot_transfer(inode, transfer_to);
+	if (err)
+		set_sbi_flag(sbi, SBI_QUOTA_NEED_REPAIR);
+	dqput(transfer_to[PRJQUOTA]);
 	return err;
 }
 
@@ -3020,7 +3088,7 @@
 	}
 	f2fs_put_page(ipage, 1);
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		return err;
 
@@ -3143,17 +3211,17 @@
 
 	inode_lock(inode);
 
-	if (f2fs_should_update_outplace(inode, NULL)) {
-		ret = -EINVAL;
-		goto out;
-	}
-
 	if (!pin) {
 		clear_inode_flag(inode, FI_PIN_FILE);
 		f2fs_i_gc_failures_write(inode, 0);
 		goto done;
 	}
 
+	if (f2fs_should_update_outplace(inode, NULL)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	if (f2fs_pin_file_control(inode, false)) {
 		ret = -EAGAIN;
 		goto out;
@@ -3200,6 +3268,7 @@
 		return -EOPNOTSUPP;
 
 	map.m_lblk = 0;
+	map.m_pblk = 0;
 	map.m_next_pgofs = NULL;
 	map.m_next_extent = &m_next_extent;
 	map.m_seg_type = NO_CHECK_TYPE;
@@ -3241,7 +3310,7 @@
 			   sizeof(block_count)))
 		return -EFAULT;
 
-	return f2fs_resize_fs(sbi, block_count);
+	return f2fs_resize_fs(filp, block_count);
 }
 
 static int f2fs_ioc_enable_verity(struct file *filp, unsigned long arg)
@@ -3416,12 +3485,9 @@
 	int ret;
 	int writecount;
 
-	if (!f2fs_sb_has_compression(F2FS_I_SB(inode)))
+	if (!f2fs_sb_has_compression(sbi))
 		return -EOPNOTSUPP;
 
-	if (!f2fs_compressed_file(inode))
-		return -EINVAL;
-
 	if (f2fs_readonly(sbi->sb))
 		return -EROFS;
 
@@ -3429,7 +3495,7 @@
 	if (ret)
 		return ret;
 
-	f2fs_balance_fs(F2FS_I_SB(inode), true);
+	f2fs_balance_fs(sbi, true);
 
 	inode_lock(inode);
 
@@ -3440,7 +3506,8 @@
 		goto out;
 	}
 
-	if (is_inode_flag_set(inode, FI_COMPRESS_RELEASED)) {
+	if (!f2fs_compressed_file(inode) ||
+		is_inode_flag_set(inode, FI_COMPRESS_RELEASED)) {
 		ret = -EINVAL;
 		goto out;
 	}
@@ -3465,9 +3532,12 @@
 		struct dnode_of_data dn;
 		pgoff_t end_offset, count;
 
+		f2fs_lock_op(sbi);
+
 		set_new_dnode(&dn, inode, NULL, NULL, 0);
 		ret = f2fs_get_dnode_of_data(&dn, page_idx, LOOKUP_NODE);
 		if (ret) {
+			f2fs_unlock_op(sbi);
 			if (ret == -ENOENT) {
 				page_idx = f2fs_get_next_page_offset(&dn,
 								page_idx);
@@ -3485,6 +3555,8 @@
 
 		f2fs_put_dnode(&dn);
 
+		f2fs_unlock_op(sbi);
+
 		if (ret < 0)
 			break;
 
@@ -3515,10 +3587,10 @@
 	return ret;
 }
 
-static int reserve_compress_blocks(struct dnode_of_data *dn, pgoff_t count)
+static int reserve_compress_blocks(struct dnode_of_data *dn, pgoff_t count,
+		unsigned int *reserved_blocks)
 {
 	struct f2fs_sb_info *sbi = F2FS_I_SB(dn->inode);
-	unsigned int reserved_blocks = 0;
 	int cluster_size = F2FS_I(dn->inode)->i_cluster_size;
 	block_t blkaddr;
 	int i;
@@ -3549,7 +3621,13 @@
 				goto next;
 			}
 
-			if (__is_valid_data_blkaddr(blkaddr)) {
+			/*
+			 * compressed cluster was not released due to it
+			 * fails in release_compress_blocks(), so NEW_ADDR
+			 * is a possible case.
+			 */
+			if (blkaddr == NEW_ADDR ||
+				__is_valid_data_blkaddr(blkaddr)) {
 				compr_blocks++;
 				continue;
 			}
@@ -3559,6 +3637,11 @@
 		}
 
 		reserved = cluster_size - compr_blocks;
+
+		/* for the case all blocks in cluster were reserved */
+		if (reserved == 1)
+			goto next;
+
 		ret = inc_valid_block_count(sbi, dn->inode, &reserved);
 		if (ret)
 			return ret;
@@ -3568,12 +3651,12 @@
 
 		f2fs_i_compr_blocks_update(dn->inode, compr_blocks, true);
 
-		reserved_blocks += reserved;
+		*reserved_blocks += reserved;
 next:
 		count -= cluster_size;
 	}
 
-	return reserved_blocks;
+	return 0;
 }
 
 static int f2fs_reserve_compress_blocks(struct file *filp, unsigned long arg)
@@ -3584,12 +3667,9 @@
 	unsigned int reserved_blocks = 0;
 	int ret;
 
-	if (!f2fs_sb_has_compression(F2FS_I_SB(inode)))
+	if (!f2fs_sb_has_compression(sbi))
 		return -EOPNOTSUPP;
 
-	if (!f2fs_compressed_file(inode))
-		return -EINVAL;
-
 	if (f2fs_readonly(sbi->sb))
 		return -EROFS;
 
@@ -3600,11 +3680,12 @@
 	if (atomic_read(&F2FS_I(inode)->i_compr_blocks))
 		goto out;
 
-	f2fs_balance_fs(F2FS_I_SB(inode), true);
+	f2fs_balance_fs(sbi, true);
 
 	inode_lock(inode);
 
-	if (!is_inode_flag_set(inode, FI_COMPRESS_RELEASED)) {
+	if (!f2fs_compressed_file(inode) ||
+		!is_inode_flag_set(inode, FI_COMPRESS_RELEASED)) {
 		ret = -EINVAL;
 		goto unlock_inode;
 	}
@@ -3618,9 +3699,12 @@
 		struct dnode_of_data dn;
 		pgoff_t end_offset, count;
 
+		f2fs_lock_op(sbi);
+
 		set_new_dnode(&dn, inode, NULL, NULL, 0);
 		ret = f2fs_get_dnode_of_data(&dn, page_idx, LOOKUP_NODE);
 		if (ret) {
+			f2fs_unlock_op(sbi);
 			if (ret == -ENOENT) {
 				page_idx = f2fs_get_next_page_offset(&dn,
 								page_idx);
@@ -3634,21 +3718,22 @@
 		count = min(end_offset - dn.ofs_in_node, last_idx - page_idx);
 		count = round_up(count, F2FS_I(inode)->i_cluster_size);
 
-		ret = reserve_compress_blocks(&dn, count);
+		ret = reserve_compress_blocks(&dn, count, &reserved_blocks);
 
 		f2fs_put_dnode(&dn);
 
+		f2fs_unlock_op(sbi);
+
 		if (ret < 0)
 			break;
 
 		page_idx += count;
-		reserved_blocks += ret;
 	}
 
 	filemap_invalidate_unlock(inode->i_mapping);
 	up_write(&F2FS_I(inode)->i_gc_rwsem[WRITE]);
 
-	if (ret >= 0) {
+	if (!ret) {
 		clear_inode_flag(inode, FI_COMPRESS_RELEASED);
 		inode->i_ctime = current_time(inode);
 		f2fs_mark_inode_dirty_sync(inode, true);
@@ -3658,7 +3743,7 @@
 out:
 	mnt_drop_write_file(filp);
 
-	if (ret >= 0) {
+	if (!ret) {
 		ret = put_user(reserved_blocks, (u64 __user *)arg);
 	} else if (reserved_blocks &&
 			atomic_read(&F2FS_I(inode)->i_compr_blocks)) {
@@ -3919,7 +4004,7 @@
 		goto out;
 	}
 
-	if (inode->i_size != 0) {
+	if (F2FS_HAS_BLOCKS(inode)) {
 		ret = -EFBIG;
 		goto out;
 	}
@@ -3960,11 +4045,14 @@
 
 	for (i = 0; i < page_len; i++, redirty_idx++) {
 		page = find_lock_page(mapping, redirty_idx);
-		if (!page) {
-			ret = -ENOMEM;
-			break;
-		}
+
+		/* It will never fail, when page has pinned above */
+		f2fs_bug_on(F2FS_I_SB(inode), !page);
+
+		f2fs_wait_on_page_writeback(page, DATA, true, true);
+
 		set_page_dirty(page);
+		set_page_private_gcing(page);
 		f2fs_put_page(page, 1);
 		f2fs_put_page(page, 0);
 	}
@@ -3989,10 +4077,7 @@
 	if (!(filp->f_mode & FMODE_WRITE))
 		return -EBADF;
 
-	if (!f2fs_compressed_file(inode))
-		return -EINVAL;
-
-	f2fs_balance_fs(F2FS_I_SB(inode), true);
+	f2fs_balance_fs(sbi, true);
 
 	file_start_write(filp);
 	inode_lock(inode);
@@ -4002,8 +4087,9 @@
 		goto out;
 	}
 
-	if (f2fs_is_mmap_file(inode)) {
-		ret = -EBUSY;
+	if (!f2fs_compressed_file(inode) ||
+		is_inode_flag_set(inode, FI_COMPRESS_RELEASED)) {
+		ret = -EINVAL;
 		goto out;
 	}
 
@@ -4061,10 +4147,7 @@
 	if (!(filp->f_mode & FMODE_WRITE))
 		return -EBADF;
 
-	if (!f2fs_compressed_file(inode))
-		return -EINVAL;
-
-	f2fs_balance_fs(F2FS_I_SB(inode), true);
+	f2fs_balance_fs(sbi, true);
 
 	file_start_write(filp);
 	inode_lock(inode);
@@ -4074,8 +4157,9 @@
 		goto out;
 	}
 
-	if (f2fs_is_mmap_file(inode)) {
-		ret = -EBUSY;
+	if (!f2fs_compressed_file(inode) ||
+		is_inode_flag_set(inode, FI_COMPRESS_RELEASED)) {
+		ret = -EINVAL;
 		goto out;
 	}
 
@@ -4239,6 +4323,8 @@
 {
 	struct file *file = iocb->ki_filp;
 	struct inode *inode = file_inode(file);
+	const loff_t orig_pos = iocb->ki_pos;
+	const size_t orig_count = iov_iter_count(from);
 	ssize_t ret;
 
 	if (unlikely(f2fs_cp_error(F2FS_I_SB(inode)))) {
@@ -4276,7 +4362,7 @@
 		size_t target_size = 0;
 		int err;
 
-		if (iov_iter_fault_in_readable(from, iov_iter_count(from)))
+		if (fault_in_iov_iter_readable(from, iov_iter_count(from)))
 			set_inode_flag(inode, FI_NO_PREALLOC);
 
 		if ((iocb->ki_flags & IOCB_NOWAIT)) {
@@ -4342,8 +4428,7 @@
 unlock:
 	inode_unlock(inode);
 out:
-	trace_f2fs_file_write_iter(inode, iocb->ki_pos,
-					iov_iter_count(from), ret);
+	trace_f2fs_file_write_iter(inode, orig_pos, orig_count, ret);
 	if (ret > 0)
 		ret = generic_write_sync(iocb, ret);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/gc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/gc.c
@@ -944,7 +944,7 @@
 			continue;
 		}
 
-		if (f2fs_get_node_info(sbi, nid, &ni)) {
+		if (f2fs_get_node_info(sbi, nid, &ni, false)) {
 			f2fs_put_page(node_page, 1);
 			continue;
 		}
@@ -1002,7 +1002,7 @@
 {
 	struct page *node_page;
 	nid_t nid;
-	unsigned int ofs_in_node;
+	unsigned int ofs_in_node, max_addrs, base;
 	block_t source_blkaddr;
 
 	nid = le32_to_cpu(sum->nid);
@@ -1012,7 +1012,7 @@
 	if (IS_ERR(node_page))
 		return false;
 
-	if (f2fs_get_node_info(sbi, nid, dni)) {
+	if (f2fs_get_node_info(sbi, nid, dni, false)) {
 		f2fs_put_page(node_page, 1);
 		return false;
 	}
@@ -1023,6 +1023,26 @@
 		set_sbi_flag(sbi, SBI_NEED_FSCK);
 	}
 
+	if (f2fs_check_nid_range(sbi, dni->ino)) {
+		f2fs_put_page(node_page, 1);
+		return false;
+	}
+
+	if (IS_INODE(node_page)) {
+		base = offset_in_addr(F2FS_INODE(node_page));
+		max_addrs = DEF_ADDRS_PER_INODE;
+	} else {
+		base = 0;
+		max_addrs = DEF_ADDRS_PER_BLOCK;
+	}
+
+	if (base + ofs_in_node >= max_addrs) {
+		f2fs_err(sbi, "Inconsistent blkaddr offset: base:%u, ofs_in_node:%u, max:%u, ino:%u, nid:%u",
+			base, ofs_in_node, max_addrs, dni->ino, dni->nid);
+		f2fs_put_page(node_page, 1);
+		return false;
+	}
+
 	*nofs = ofs_of_node(node_page);
 	source_blkaddr = data_blkaddr(NULL, node_page, ofs_in_node);
 	f2fs_put_page(node_page, 1);
@@ -1036,7 +1056,7 @@
 			if (!test_and_set_bit(segno, SIT_I(sbi)->invalid_segmap)) {
 				f2fs_err(sbi, "mismatched blkaddr %u (source_blkaddr %u) in seg %u",
 					 blkaddr, source_blkaddr, segno);
-				f2fs_bug_on(sbi, 1);
+				set_sbi_flag(sbi, SBI_NEED_FSCK);
 			}
 		}
 #endif
@@ -1060,8 +1080,8 @@
 		.op = REQ_OP_READ,
 		.op_flags = 0,
 		.encrypted_page = NULL,
-		.in_list = false,
-		.retry = false,
+		.in_list = 0,
+		.retry = 0,
 	};
 	int err;
 
@@ -1147,8 +1167,8 @@
 		.op = REQ_OP_READ,
 		.op_flags = 0,
 		.encrypted_page = NULL,
-		.in_list = false,
-		.retry = false,
+		.in_list = 0,
+		.retry = 0,
 	};
 	struct dnode_of_data dn;
 	struct f2fs_summary sum;
@@ -1179,7 +1199,8 @@
 	}
 
 	if (f2fs_is_pinned_file(inode)) {
-		f2fs_pin_file_control(inode, true);
+		if (gc_type == FG_GC)
+			f2fs_pin_file_control(inode, true);
 		err = -EAGAIN;
 		goto out;
 	}
@@ -1203,7 +1224,7 @@
 
 	f2fs_wait_on_block_writeback(inode, dn.data_blkaddr);
 
-	err = f2fs_get_node_info(fio.sbi, dn.nid, &ni);
+	err = f2fs_get_node_info(fio.sbi, dn.nid, &ni, false);
 	if (err)
 		goto put_out;
 
@@ -1454,8 +1475,20 @@
 
 		if (phase == 3) {
 			inode = f2fs_iget(sb, dni.ino);
-			if (IS_ERR(inode) || is_bad_inode(inode))
+			if (IS_ERR(inode) || is_bad_inode(inode) ||
+					special_file(inode->i_mode))
+				continue;
+
+			if (f2fs_has_inline_data(inode)) {
+				iput(inode);
+				set_sbi_flag(sbi, SBI_NEED_FSCK);
+				printk_ratelimited("%sF2FS-fs (%s): "
+					"inode %lx has both inline_data flag and "
+					"data block, nid=%u, ofs_in_node=%u",
+					KERN_ERR, sbi->sb->s_id,
+					inode->i_ino, dni.nid, ofs_in_node);
 				continue;
+			}
 
 			if (!down_write_trylock(
 				&F2FS_I(inode)->i_gc_rwsem[WRITE])) {
@@ -1659,8 +1692,9 @@
 				get_valid_blocks(sbi, segno, false) == 0)
 			seg_freed++;
 
-		if (__is_large_section(sbi) && segno + 1 < end_segno)
-			sbi->next_victim_seg[gc_type] = segno + 1;
+		if (__is_large_section(sbi))
+			sbi->next_victim_seg[gc_type] =
+				(segno + 1 < end_segno) ? segno + 1 : NULL_SEGNO;
 skip:
 		f2fs_put_page(sum_page, 0);
 	}
@@ -1759,23 +1793,31 @@
 	if (sync)
 		goto stop;
 
-	if (has_not_enough_free_secs(sbi, sec_freed, 0)) {
-		if (skipped_round <= MAX_SKIP_GC_COUNT ||
-					skipped_round * 2 < round) {
-			segno = NULL_SEGNO;
-			goto gc_more;
-		}
+	if (!has_not_enough_free_secs(sbi, sec_freed, 0))
+		goto stop;
 
-		if (first_skipped < last_skipped &&
-				(last_skipped - first_skipped) >
-						sbi->skipped_gc_rwsem) {
-			f2fs_drop_inmem_pages_all(sbi, true);
-			segno = NULL_SEGNO;
-			goto gc_more;
-		}
-		if (gc_type == FG_GC && !is_sbi_flag_set(sbi, SBI_CP_DISABLED))
+	if (skipped_round <= MAX_SKIP_GC_COUNT || skipped_round * 2 < round) {
+
+		/* Write checkpoint to reclaim prefree segments */
+		if (free_sections(sbi) < NR_CURSEG_PERSIST_TYPE &&
+				prefree_segments(sbi) &&
+				!is_sbi_flag_set(sbi, SBI_CP_DISABLED)) {
 			ret = f2fs_write_checkpoint(sbi, &cpc);
+			if (ret)
+				goto stop;
+		}
+		segno = NULL_SEGNO;
+		goto gc_more;
 	}
+	if (first_skipped < last_skipped &&
+			(last_skipped - first_skipped) >
+					sbi->skipped_gc_rwsem) {
+		f2fs_drop_inmem_pages_all(sbi, true);
+		segno = NULL_SEGNO;
+		goto gc_more;
+	}
+	if (gc_type == FG_GC && !is_sbi_flag_set(sbi, SBI_CP_DISABLED))
+		ret = f2fs_write_checkpoint(sbi, &cpc);
 stop:
 	SIT_I(sbi)->last_victim[ALLOC_NEXT] = 0;
 	SIT_I(sbi)->last_victim[FLUSH_DEVICE] = init_segno;
@@ -1970,8 +2012,9 @@
 	}
 }
 
-int f2fs_resize_fs(struct f2fs_sb_info *sbi, __u64 block_count)
+int f2fs_resize_fs(struct file *filp, __u64 block_count)
 {
+	struct f2fs_sb_info *sbi = F2FS_I_SB(file_inode(filp));
 	__u64 old_block_count, shrunk_blocks;
 	struct cp_control cpc = { CP_RESIZE, 0, 0, 0 };
 	unsigned int secs;
@@ -2009,12 +2052,18 @@
 		return -EINVAL;
 	}
 
+	err = mnt_want_write_file(filp);
+	if (err)
+		return err;
+
 	shrunk_blocks = old_block_count - block_count;
 	secs = div_u64(shrunk_blocks, BLKS_PER_SEC(sbi));
 
 	/* stop other GC */
-	if (!down_write_trylock(&sbi->gc_lock))
-		return -EAGAIN;
+	if (!down_write_trylock(&sbi->gc_lock)) {
+		err = -EAGAIN;
+		goto out_drop_write;
+	}
 
 	/* stop CP to protect MAIN_SEC in free_segment_range */
 	f2fs_lock_op(sbi);
@@ -2034,12 +2083,18 @@
 out_unlock:
 	f2fs_unlock_op(sbi);
 	up_write(&sbi->gc_lock);
+out_drop_write:
+	mnt_drop_write_file(filp);
 	if (err)
 		return err;
 
-	set_sbi_flag(sbi, SBI_IS_RESIZEFS);
-
 	freeze_super(sbi->sb);
+
+	if (f2fs_readonly(sbi->sb)) {
+		thaw_super(sbi->sb);
+		return -EROFS;
+	}
+
 	down_write(&sbi->gc_lock);
 	down_write(&sbi->cp_global_sem);
 
@@ -2054,6 +2109,7 @@
 	if (err)
 		goto out_err;
 
+	set_sbi_flag(sbi, SBI_IS_RESIZEFS);
 	err = free_segment_range(sbi, secs, false);
 	if (err)
 		goto recover_out;
@@ -2077,6 +2133,7 @@
 		f2fs_commit_super(sbi, false);
 	}
 recover_out:
+	clear_sbi_flag(sbi, SBI_IS_RESIZEFS);
 	if (err) {
 		set_sbi_flag(sbi, SBI_NEED_FSCK);
 		f2fs_err(sbi, "resize_fs failed, should run fsck to repair!");
@@ -2089,6 +2146,5 @@
 	up_write(&sbi->cp_global_sem);
 	up_write(&sbi->gc_lock);
 	thaw_super(sbi->sb);
-	clear_sbi_flag(sbi, SBI_IS_RESIZEFS);
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/hash.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/hash.c
@@ -91,7 +91,7 @@
 /*
  * Compute @fname->hash.  For all directories, @fname->disk_name must be set.
  * For casefolded directories, @fname->usr_fname must be set, and also
- * @fname->cf_name if the filename is valid Unicode.
+ * @fname->cf_name if the filename is valid Unicode and is not "." or "..".
  */
 void f2fs_hash_filename(const struct inode *dir, struct f2fs_filename *fname)
 {
@@ -110,10 +110,11 @@
 		/*
 		 * If the casefolded name is provided, hash it instead of the
 		 * on-disk name.  If the casefolded name is *not* provided, that
-		 * should only be because the name wasn't valid Unicode, so fall
-		 * back to treating the name as an opaque byte sequence.  Note
-		 * that to handle encrypted directories, the fallback must use
-		 * usr_fname (plaintext) rather than disk_name (ciphertext).
+		 * should only be because the name wasn't valid Unicode or was
+		 * "." or "..", so fall back to treating the name as an opaque
+		 * byte sequence.  Note that to handle encrypted directories,
+		 * the fallback must use usr_fname (plaintext) rather than
+		 * disk_name (ciphertext).
 		 */
 		WARN_ON_ONCE(!fname->usr_fname->name);
 		if (fname->cf_name.name) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/inline.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/inline.c
@@ -14,21 +14,40 @@
 #include "node.h"
 #include <trace/events/f2fs.h>
 
-bool f2fs_may_inline_data(struct inode *inode)
+static bool support_inline_data(struct inode *inode)
 {
 	if (f2fs_is_atomic_file(inode))
 		return false;
-
 	if (!S_ISREG(inode->i_mode) && !S_ISLNK(inode->i_mode))
 		return false;
-
 	if (i_size_read(inode) > MAX_INLINE_DATA(inode))
 		return false;
+	return true;
+}
 
-	if (f2fs_post_read_required(inode))
+bool f2fs_may_inline_data(struct inode *inode)
+{
+	if (!support_inline_data(inode))
 		return false;
 
-	return true;
+	return !f2fs_post_read_required(inode);
+}
+
+bool f2fs_sanity_check_inline_data(struct inode *inode)
+{
+	if (!f2fs_has_inline_data(inode))
+		return false;
+
+	if (!support_inline_data(inode))
+		return true;
+
+	/*
+	 * used by sanity_check_inode(), when disk layout fields has not
+	 * been synchronized to inmem fields.
+	 */
+	return (S_ISREG(inode->i_mode) &&
+		(file_is_encrypt(inode) || file_is_verity(inode) ||
+		(F2FS_I(inode)->i_flags & F2FS_COMPR_FL)));
 }
 
 bool f2fs_may_inline_dentry(struct inode *inode)
@@ -45,7 +64,6 @@
 void f2fs_do_read_inline_data(struct page *page, struct page *ipage)
 {
 	struct inode *inode = page->mapping->host;
-	void *src_addr, *dst_addr;
 
 	if (PageUptodate(page))
 		return;
@@ -55,11 +73,8 @@
 	zero_user_segment(page, MAX_INLINE_DATA(inode), PAGE_SIZE);
 
 	/* Copy the whole inline data block */
-	src_addr = inline_data_addr(inode, ipage);
-	dst_addr = kmap_atomic(page);
-	memcpy(dst_addr, src_addr, MAX_INLINE_DATA(inode));
-	flush_dcache_page(page);
-	kunmap_atomic(dst_addr);
+	memcpy_to_page(page, 0, inline_data_addr(inode, ipage),
+		       MAX_INLINE_DATA(inode));
 	if (!PageUptodate(page))
 		SetPageUptodate(page);
 }
@@ -131,7 +146,7 @@
 	if (err)
 		return err;
 
-	err = f2fs_get_node_info(fio.sbi, dn->nid, &ni);
+	err = f2fs_get_node_info(fio.sbi, dn->nid, &ni, false);
 	if (err) {
 		f2fs_truncate_data_blocks_range(dn, 1);
 		f2fs_put_dnode(dn);
@@ -188,11 +203,13 @@
 	struct page *ipage, *page;
 	int err = 0;
 
-	if (!f2fs_has_inline_data(inode) ||
-			f2fs_hw_is_readonly(sbi) || f2fs_readonly(sbi->sb))
+	if (f2fs_hw_is_readonly(sbi) || f2fs_readonly(sbi->sb))
+		return -EROFS;
+
+	if (!f2fs_has_inline_data(inode))
 		return 0;
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		return err;
 
@@ -227,7 +244,6 @@
 
 int f2fs_write_inline_data(struct inode *inode, struct page *page)
 {
-	void *src_addr, *dst_addr;
 	struct dnode_of_data dn;
 	int err;
 
@@ -244,10 +260,8 @@
 	f2fs_bug_on(F2FS_I_SB(inode), page->index);
 
 	f2fs_wait_on_page_writeback(dn.inode_page, NODE, true, true);
-	src_addr = kmap_atomic(page);
-	dst_addr = inline_data_addr(inode, dn.inode_page);
-	memcpy(dst_addr, src_addr, MAX_INLINE_DATA(inode));
-	kunmap_atomic(src_addr);
+	memcpy_from_page(inline_data_addr(inode, dn.inode_page),
+			 page, 0, MAX_INLINE_DATA(inode));
 	set_page_dirty(dn.inode_page);
 
 	f2fs_clear_page_cache_dirty_tag(page);
@@ -321,7 +335,8 @@
 
 struct f2fs_dir_entry *f2fs_find_in_inline_dir(struct inode *dir,
 					const struct f2fs_filename *fname,
-					struct page **res_page)
+					struct page **res_page,
+					bool use_hash)
 {
 	struct f2fs_sb_info *sbi = F2FS_SB(dir->i_sb);
 	struct f2fs_dir_entry *de;
@@ -338,7 +353,7 @@
 	inline_dentry = inline_data_addr(dir, ipage);
 
 	make_dentry_ptr_inline(dir, &d, inline_dentry);
-	de = f2fs_find_target_dentry(&d, fname, NULL);
+	de = f2fs_find_target_dentry(&d, fname, NULL, use_hash);
 	unlock_page(ipage);
 	if (IS_ERR(de)) {
 		*res_page = ERR_CAST(de);
@@ -408,18 +423,17 @@
 
 	dentry_blk = page_address(page);
 
+	/*
+	 * Start by zeroing the full block, to ensure that all unused space is
+	 * zeroed and no uninitialized memory is leaked to disk.
+	 */
+	memset(dentry_blk, 0, F2FS_BLKSIZE);
+
 	make_dentry_ptr_inline(dir, &src, inline_dentry);
 	make_dentry_ptr_block(dir, &dst, dentry_blk);
 
 	/* copy data from inline dentry block to new dentry block */
 	memcpy(dst.bitmap, src.bitmap, src.nr_bitmap);
-	memset(dst.bitmap + src.nr_bitmap, 0, dst.nr_bitmap - src.nr_bitmap);
-	/*
-	 * we do not need to zero out remainder part of dentry and filename
-	 * field, since we have used bitmap for marking the usage status of
-	 * them, besides, we can also ignore copying/zeroing reserved space
-	 * of dentry block, because them haven't been used so far.
-	 */
 	memcpy(dst.dentry, src.dentry, SIZE_OF_DIR_ENTRY * src.max);
 	memcpy(dst.filename, src.filename, src.max * F2FS_SLOT_LEN);
 
@@ -786,7 +800,7 @@
 		ilen = start + len;
 	ilen -= start;
 
-	err = f2fs_get_node_info(F2FS_I_SB(inode), inode->i_ino, &ni);
+	err = f2fs_get_node_info(F2FS_I_SB(inode), inode->i_ino, &ni, false);
 	if (err)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/inode.c
@@ -27,6 +27,9 @@
 	if (is_inode_flag_set(inode, FI_NEW_INODE))
 		return;
 
+	if (f2fs_readonly(F2FS_I_SB(inode)->sb))
+		return;
+
 	if (f2fs_inode_dirtied(inode, sync))
 		return;
 
@@ -276,8 +279,7 @@
 		}
 	}
 
-	if (f2fs_has_inline_data(inode) &&
-			(!S_ISREG(inode->i_mode) && !S_ISLNK(inode->i_mode))) {
+	if (f2fs_sanity_check_inline_data(inode)) {
 		set_sbi_flag(sbi, SBI_NEED_FSCK);
 		f2fs_warn(sbi, "%s: inode (ino=%lx, mode=%u) should not have inline_data, run fsck to fix",
 			  __func__, inode->i_ino, inode->i_mode);
@@ -331,6 +333,12 @@
 		}
 	}
 
+	if (fi->i_xattr_nid && f2fs_check_nid_range(sbi, fi->i_xattr_nid)) {
+		f2fs_warn(sbi, "%s: inode (ino=%lx) has corrupted i_xattr_nid: %u, run fsck to fix.",
+			  __func__, inode->i_ino, fi->i_xattr_nid);
+		return false;
+	}
+
 	return true;
 }
 
@@ -516,6 +524,11 @@
 	} else if (ino == F2FS_COMPRESS_INO(sbi)) {
 #ifdef CONFIG_F2FS_FS_COMPRESSION
 		inode->i_mapping->a_ops = &f2fs_compress_aops;
+		/*
+		 * generic_error_remove_page only truncates pages of regular
+		 * inode
+		 */
+		inode->i_mode |= S_IFREG;
 #endif
 		mapping_set_gfp_mask(inode->i_mapping,
 			GFP_NOFS | __GFP_HIGHMEM | __GFP_MOVABLE);
@@ -527,7 +540,7 @@
 		inode->i_op = &f2fs_dir_inode_operations;
 		inode->i_fop = &f2fs_dir_operations;
 		inode->i_mapping->a_ops = &f2fs_dblock_aops;
-		inode_nohighmem(inode);
+		mapping_set_gfp_mask(inode->i_mapping, GFP_NOFS);
 	} else if (S_ISLNK(inode->i_mode)) {
 		if (file_is_encrypt(inode))
 			inode->i_op = &f2fs_encrypted_symlink_inode_operations;
@@ -677,17 +690,19 @@
 {
 	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	struct page *node_page;
+	int count = 0;
 retry:
 	node_page = f2fs_get_node_page(sbi, inode->i_ino);
 	if (IS_ERR(node_page)) {
 		int err = PTR_ERR(node_page);
 
-		if (err == -ENOMEM) {
-			cond_resched();
+		/* The node block was truncated. */
+		if (err == -ENOENT)
+			return;
+
+		if (err == -ENOMEM || ++count <= DEFAULT_RETRY_IO_COUNT)
 			goto retry;
-		} else if (err != -ENOENT) {
-			f2fs_stop_checkpoint(sbi, false);
-		}
+		f2fs_stop_checkpoint(sbi, false);
 		return;
 	}
 	f2fs_update_inode(inode, node_page);
@@ -709,8 +724,10 @@
 		!is_inode_flag_set(inode, FI_DIRTY_INODE))
 		return 0;
 
-	if (!f2fs_is_checkpoint_ready(sbi))
+	if (!f2fs_is_checkpoint_ready(sbi)) {
+		f2fs_mark_inode_dirty_sync(inode, true);
 		return -ENOSPC;
+	}
 
 	/*
 	 * We need to balance fs here to prevent from producing dirty node pages
@@ -754,7 +771,7 @@
 	if (inode->i_nlink || is_bad_inode(inode))
 		goto no_delete;
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err) {
 		err = 0;
 		set_sbi_flag(sbi, SBI_QUOTA_NEED_REPAIR);
@@ -764,7 +781,8 @@
 	f2fs_remove_ino_entry(sbi, inode->i_ino, UPDATE_INO);
 	f2fs_remove_ino_entry(sbi, inode->i_ino, FLUSH_INO);
 
-	sb_start_intwrite(inode->i_sb);
+	if (!is_sbi_flag_set(sbi, SBI_IS_FREEZING))
+		sb_start_intwrite(inode->i_sb);
 	set_inode_flag(inode, FI_NO_ALLOC);
 	i_size_write(inode, 0);
 retry:
@@ -780,8 +798,22 @@
 		f2fs_lock_op(sbi);
 		err = f2fs_remove_inode_page(inode);
 		f2fs_unlock_op(sbi);
-		if (err == -ENOENT)
+		if (err == -ENOENT) {
 			err = 0;
+
+			/*
+			 * in fuzzed image, another node may has the same
+			 * block address as inode's, if it was truncated
+			 * previously, truncation of inode node will fail.
+			 */
+			if (is_inode_flag_set(inode, FI_DIRTY_INODE)) {
+				f2fs_warn(F2FS_I_SB(inode),
+					"f2fs_evict_inode: inconsistent node id, ino:%lu",
+					inode->i_ino);
+				f2fs_inode_synced(inode);
+				set_sbi_flag(sbi, SBI_NEED_FSCK);
+			}
+		}
 	}
 
 	/* give more chances, if ENOMEM case */
@@ -795,7 +827,8 @@
 		if (dquot_initialize_needed(inode))
 			set_sbi_flag(sbi, SBI_QUOTA_NEED_REPAIR);
 	}
-	sb_end_intwrite(inode->i_sb);
+	if (!is_sbi_flag_set(sbi, SBI_IS_FREEZING))
+		sb_end_intwrite(inode->i_sb);
 no_delete:
 	dquot_drop(inode);
 
@@ -868,9 +901,10 @@
 	 * so we can prevent losing this orphan when encoutering checkpoint
 	 * and following suddenly power-off.
 	 */
-	err = f2fs_get_node_info(sbi, inode->i_ino, &ni);
+	err = f2fs_get_node_info(sbi, inode->i_ino, &ni, false);
 	if (err) {
 		set_sbi_flag(sbi, SBI_NEED_FSCK);
+		set_inode_flag(inode, FI_FREE_NID);
 		f2fs_warn(sbi, "May loss orphan inode, run fsck to fix.");
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/iostat.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/iostat.c
@@ -194,8 +194,12 @@
 		return;
 
 	ts_diff = jiffies - iostat_ctx->submit_ts;
-	if (iotype >= META_FLUSH)
+	if (iotype == META_FLUSH) {
 		iotype = META;
+	} else if (iotype >= NR_PAGE_TYPE) {
+		f2fs_warn(sbi, "%s: %d over NR_PAGE_TYPE", __func__, iotype);
+		return;
+	}
 
 	if (rw == 0) {
 		idx = READ_IO;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/namei.c
@@ -74,7 +74,7 @@
 	if (err)
 		goto fail_drop;
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		goto fail_drop;
 
@@ -91,8 +91,6 @@
 	if (test_opt(sbi, INLINE_XATTR))
 		set_inode_flag(inode, FI_INLINE_XATTR);
 
-	if (test_opt(sbi, INLINE_DATA) && f2fs_may_inline_data(inode))
-		set_inode_flag(inode, FI_INLINE_DATA);
 	if (f2fs_may_inline_dentry(inode))
 		set_inode_flag(inode, FI_INLINE_DENTRY);
 
@@ -109,10 +107,6 @@
 
 	f2fs_init_extent_tree(inode, NULL);
 
-	stat_inc_inline_xattr(inode);
-	stat_inc_inline_inode(inode);
-	stat_inc_inline_dir(inode);
-
 	F2FS_I(inode)->i_flags =
 		f2fs_mask_flags(mode, F2FS_I(dir)->i_flags & F2FS_FL_INHERITED);
 
@@ -129,6 +123,14 @@
 			set_compress_context(inode);
 	}
 
+	/* Should enable inline_data after compression set */
+	if (test_opt(sbi, INLINE_DATA) && f2fs_may_inline_data(inode))
+		set_inode_flag(inode, FI_INLINE_DATA);
+
+	stat_inc_inline_xattr(inode);
+	stat_inc_inline_inode(inode);
+	stat_inc_inline_dir(inode);
+
 	f2fs_set_inode_flags(inode);
 
 	trace_f2fs_new_inode(inode, 0);
@@ -327,6 +329,9 @@
 		if (!is_extension_exist(name, ext[i], false))
 			continue;
 
+		/* Do not use inline_data with compression */
+		stat_dec_inline_inode(inode);
+		clear_inode_flag(inode, FI_INLINE_DATA);
 		set_compress_context(inode);
 		return;
 	}
@@ -345,7 +350,7 @@
 	if (!f2fs_is_checkpoint_ready(sbi))
 		return -ENOSPC;
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		return err;
 
@@ -404,7 +409,7 @@
 			F2FS_I(old_dentry->d_inode)->i_projid)))
 		return -EXDEV;
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		return err;
 
@@ -445,56 +450,6 @@
 	return d_obtain_alias(f2fs_iget(child->d_sb, ino));
 }
 
-static int __recover_dot_dentries(struct inode *dir, nid_t pino)
-{
-	struct f2fs_sb_info *sbi = F2FS_I_SB(dir);
-	struct qstr dot = QSTR_INIT(".", 1);
-	struct qstr dotdot = QSTR_INIT("..", 2);
-	struct f2fs_dir_entry *de;
-	struct page *page;
-	int err = 0;
-
-	if (f2fs_readonly(sbi->sb)) {
-		f2fs_info(sbi, "skip recovering inline_dots inode (ino:%lu, pino:%u) in readonly mountpoint",
-			  dir->i_ino, pino);
-		return 0;
-	}
-
-	err = dquot_initialize(dir);
-	if (err)
-		return err;
-
-	f2fs_balance_fs(sbi, true);
-
-	f2fs_lock_op(sbi);
-
-	de = f2fs_find_entry(dir, &dot, &page);
-	if (de) {
-		f2fs_put_page(page, 0);
-	} else if (IS_ERR(page)) {
-		err = PTR_ERR(page);
-		goto out;
-	} else {
-		err = f2fs_do_add_link(dir, &dot, NULL, dir->i_ino, S_IFDIR);
-		if (err)
-			goto out;
-	}
-
-	de = f2fs_find_entry(dir, &dotdot, &page);
-	if (de)
-		f2fs_put_page(page, 0);
-	else if (IS_ERR(page))
-		err = PTR_ERR(page);
-	else
-		err = f2fs_do_add_link(dir, &dotdot, NULL, pino, S_IFDIR);
-out:
-	if (!err)
-		clear_inode_flag(dir, FI_INLINE_DOTS);
-
-	f2fs_unlock_op(sbi);
-	return err;
-}
-
 static struct dentry *f2fs_lookup(struct inode *dir, struct dentry *dentry,
 		unsigned int flags)
 {
@@ -504,7 +459,6 @@
 	struct dentry *new;
 	nid_t ino = -1;
 	int err = 0;
-	unsigned int root_ino = F2FS_ROOT_INO(F2FS_I_SB(dir));
 	struct f2fs_filename fname;
 
 	trace_f2fs_lookup_start(dir, dentry, flags);
@@ -541,17 +495,6 @@
 		goto out;
 	}
 
-	if ((dir->i_ino == root_ino) && f2fs_has_inline_dots(dir)) {
-		err = __recover_dot_dentries(dir, root_ino);
-		if (err)
-			goto out_iput;
-	}
-
-	if (f2fs_has_inline_dots(inode)) {
-		err = __recover_dot_dentries(inode, dir->i_ino);
-		if (err)
-			goto out_iput;
-	}
 	if (IS_ENCRYPTED(dir) &&
 	    (S_ISDIR(inode->i_mode) || S_ISLNK(inode->i_mode)) &&
 	    !fscrypt_has_permitted_context(dir, inode)) {
@@ -598,10 +541,10 @@
 		goto fail;
 	}
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		goto fail;
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		goto fail;
 
@@ -675,7 +618,7 @@
 	if (err)
 		return err;
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		return err;
 
@@ -746,7 +689,7 @@
 	if (unlikely(f2fs_cp_error(sbi)))
 		return -EIO;
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		return err;
 
@@ -757,7 +700,7 @@
 	inode->i_op = &f2fs_dir_inode_operations;
 	inode->i_fop = &f2fs_dir_operations;
 	inode->i_mapping->a_ops = &f2fs_dblock_aops;
-	inode_nohighmem(inode);
+	mapping_set_gfp_mask(inode->i_mapping, GFP_NOFS);
 
 	set_inode_flag(inode, FI_INC_LINK);
 	f2fs_lock_op(sbi);
@@ -803,7 +746,7 @@
 	if (!f2fs_is_checkpoint_ready(sbi))
 		return -ENOSPC;
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		return err;
 
@@ -841,7 +784,7 @@
 	struct inode *inode;
 	int err;
 
-	err = dquot_initialize(dir);
+	err = f2fs_dquot_initialize(dir);
 	if (err)
 		return err;
 
@@ -947,7 +890,7 @@
 
 	/*
 	 * If new_inode is null, the below renaming flow will
-	 * add a link in old_dir which can conver inline_dir.
+	 * add a link in old_dir which can convert inline_dir.
 	 * After then, if we failed to get the entry due to other
 	 * reasons like ENOMEM, we had to remove the new entry.
 	 * Instead of adding such the error handling routine, let's
@@ -965,16 +908,16 @@
 			return err;
 	}
 
-	err = dquot_initialize(old_dir);
+	err = f2fs_dquot_initialize(old_dir);
 	if (err)
 		goto out;
 
-	err = dquot_initialize(new_dir);
+	err = f2fs_dquot_initialize(new_dir);
 	if (err)
 		goto out;
 
 	if (new_inode) {
-		err = dquot_initialize(new_inode);
+		err = f2fs_dquot_initialize(new_inode);
 		if (err)
 			goto out;
 	}
@@ -1076,7 +1019,7 @@
 	}
 
 	if (old_dir_entry) {
-		if (old_dir != new_dir && !whiteout)
+		if (old_dir != new_dir)
 			f2fs_set_link(old_inode, old_dir_entry,
 						old_dir_page, new_dir);
 		else
@@ -1138,11 +1081,11 @@
 			F2FS_I(new_dentry->d_inode)->i_projid)))
 		return -EXDEV;
 
-	err = dquot_initialize(old_dir);
+	err = f2fs_dquot_initialize(old_dir);
 	if (err)
 		goto out;
 
-	err = dquot_initialize(new_dir);
+	err = f2fs_dquot_initialize(new_dir);
 	if (err)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/node.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/node.c
@@ -430,6 +430,10 @@
 	struct f2fs_nm_info *nm_i = NM_I(sbi);
 	struct nat_entry *new, *e;
 
+	/* Let's mitigate lock contention of nat_tree_lock during checkpoint */
+	if (rwsem_is_locked(&sbi->cp_global_sem))
+		return;
+
 	new = __alloc_nat_entry(sbi, nid, false);
 	if (!new)
 		return;
@@ -539,7 +543,7 @@
 }
 
 int f2fs_get_node_info(struct f2fs_sb_info *sbi, nid_t nid,
-						struct node_info *ni)
+				struct node_info *ni, bool checkpoint_context)
 {
 	struct f2fs_nm_info *nm_i = NM_I(sbi);
 	struct curseg_info *curseg = CURSEG_I(sbi, CURSEG_HOT_DATA);
@@ -572,9 +576,10 @@
 	 * nat_tree_lock. Therefore, we should retry, if we failed to grab here
 	 * while not bothering checkpoint.
 	 */
-	if (!rwsem_is_locked(&sbi->cp_global_sem)) {
+	if (!rwsem_is_locked(&sbi->cp_global_sem) || checkpoint_context) {
 		down_read(&curseg->journal_rwsem);
-	} else if (!down_read_trylock(&curseg->journal_rwsem)) {
+	} else if (rwsem_is_contended(&nm_i->nat_tree_lock) ||
+				!down_read_trylock(&curseg->journal_rwsem)) {
 		up_read(&nm_i->nat_tree_lock);
 		goto retry;
 	}
@@ -887,7 +892,7 @@
 	int err;
 	pgoff_t index;
 
-	err = f2fs_get_node_info(sbi, dn->nid, &ni);
+	err = f2fs_get_node_info(sbi, dn->nid, &ni, false);
 	if (err)
 		return err;
 
@@ -937,8 +942,10 @@
 	dn->ofs_in_node = 0;
 	f2fs_truncate_data_blocks(dn);
 	err = truncate_node(dn);
-	if (err)
+	if (err) {
+		f2fs_put_page(page, 1);
 		return err;
+	}
 
 	return 1;
 }
@@ -1286,12 +1293,17 @@
 		goto fail;
 
 #ifdef CONFIG_F2FS_CHECK_FS
-	err = f2fs_get_node_info(sbi, dn->nid, &new_ni);
+	err = f2fs_get_node_info(sbi, dn->nid, &new_ni, false);
 	if (err) {
 		dec_valid_node_count(sbi, dn->inode, !ofs);
 		goto fail;
 	}
-	f2fs_bug_on(sbi, new_ni.blk_addr != NULL_ADDR);
+	if (unlikely(new_ni.blk_addr != NULL_ADDR)) {
+		err = -EFSCORRUPTED;
+		dec_valid_node_count(sbi, dn->inode, !ofs);
+		set_sbi_flag(sbi, SBI_NEED_FSCK);
+		goto fail;
+	}
 #endif
 	new_ni.nid = dn->nid;
 	new_ni.ino = dn->inode->i_ino;
@@ -1314,7 +1326,6 @@
 	if (ofs == 0)
 		inc_valid_inode_count(sbi);
 	return page;
-
 fail:
 	clear_node_page_dirty(page);
 	f2fs_put_page(page, 1);
@@ -1348,13 +1359,12 @@
 		return LOCKED_PAGE;
 	}
 
-	err = f2fs_get_node_info(sbi, page->index, &ni);
+	err = f2fs_get_node_info(sbi, page->index, &ni, false);
 	if (err)
 		return err;
 
 	/* NEW_ADDR can be seen, after cp_error drops some dirty node pages */
-	if (unlikely(ni.blk_addr == NULL_ADDR || ni.blk_addr == NEW_ADDR) ||
-			is_sbi_flag_set(sbi, SBI_IS_SHUTDOWN)) {
+	if (unlikely(ni.blk_addr == NULL_ADDR || ni.blk_addr == NEW_ADDR)) {
 		ClearPageUptodate(page);
 		return -ENOENT;
 	}
@@ -1443,6 +1453,7 @@
 			  nid, nid_of_node(page), ino_of_node(page),
 			  ofs_of_node(page), cpver_of_node(page),
 			  next_blkaddr_of_node(page));
+		set_sbi_flag(sbi, SBI_NEED_FSCK);
 		err = -EINVAL;
 out_err:
 		ClearPageUptodate(page);
@@ -1572,7 +1583,7 @@
 		.op_flags = wbc_to_write_flags(wbc),
 		.page = page,
 		.encrypted_page = NULL,
-		.submitted = false,
+		.submitted = 0,
 		.io_type = io_type,
 		.io_wbc = wbc,
 	};
@@ -1599,7 +1610,7 @@
 	nid = nid_of_node(page);
 	f2fs_bug_on(sbi, page->index != nid);
 
-	if (f2fs_get_node_info(sbi, nid, &ni))
+	if (f2fs_get_node_info(sbi, nid, &ni, !do_balance))
 		goto redirty_out;
 
 	if (wbc->for_reclaim) {
@@ -2105,8 +2116,12 @@
 
 	if (wbc->sync_mode == WB_SYNC_ALL)
 		atomic_inc(&sbi->wb_sync_req[NODE]);
-	else if (atomic_read(&sbi->wb_sync_req[NODE]))
+	else if (atomic_read(&sbi->wb_sync_req[NODE])) {
+		/* to avoid potential deadlock */
+		if (current->plug)
+			blk_finish_plug(current->plug);
 		goto skip_write;
+	}
 
 	trace_f2fs_writepages(mapping->host, wbc, NODE);
 
@@ -2700,7 +2715,7 @@
 		goto recover_xnid;
 
 	/* 1: invalidate the previous xattr nid */
-	err = f2fs_get_node_info(sbi, prev_xnid, &ni);
+	err = f2fs_get_node_info(sbi, prev_xnid, &ni, false);
 	if (err)
 		return err;
 
@@ -2740,7 +2755,7 @@
 	struct page *ipage;
 	int err;
 
-	err = f2fs_get_node_info(sbi, ino, &old_ni);
+	err = f2fs_get_node_info(sbi, ino, &old_ni, false);
 	if (err)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/recovery.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/recovery.c
@@ -81,7 +81,7 @@
 	if (IS_ERR(inode))
 		return ERR_CAST(inode);
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		goto err_out;
 
@@ -203,7 +203,7 @@
 			goto out_put;
 		}
 
-		err = dquot_initialize(einode);
+		err = f2fs_dquot_initialize(einode);
 		if (err) {
 			iput(einode);
 			goto out_put;
@@ -452,7 +452,7 @@
 	struct dnode_of_data tdn = *dn;
 	nid_t ino, nid;
 	struct inode *inode;
-	unsigned int offset;
+	unsigned int offset, ofs_in_node, max_addrs;
 	block_t bidx;
 	int i;
 
@@ -479,15 +479,24 @@
 got_it:
 	/* Use the locked dnode page and inode */
 	nid = le32_to_cpu(sum.nid);
+	ofs_in_node = le16_to_cpu(sum.ofs_in_node);
+
+	max_addrs = ADDRS_PER_PAGE(dn->node_page, dn->inode);
+	if (ofs_in_node >= max_addrs) {
+		f2fs_err(sbi, "Inconsistent ofs_in_node:%u in summary, ino:%lu, nid:%u, max:%u",
+			ofs_in_node, dn->inode->i_ino, nid, max_addrs);
+		return -EFSCORRUPTED;
+	}
+
 	if (dn->inode->i_ino == nid) {
 		tdn.nid = nid;
 		if (!dn->inode_page_locked)
 			lock_page(dn->inode_page);
 		tdn.node_page = dn->inode_page;
-		tdn.ofs_in_node = le16_to_cpu(sum.ofs_in_node);
+		tdn.ofs_in_node = ofs_in_node;
 		goto truncate_out;
 	} else if (dn->nid == nid) {
-		tdn.ofs_in_node = le16_to_cpu(sum.ofs_in_node);
+		tdn.ofs_in_node = ofs_in_node;
 		goto truncate_out;
 	}
 
@@ -508,7 +517,7 @@
 		if (IS_ERR(inode))
 			return PTR_ERR(inode);
 
-		ret = dquot_initialize(inode);
+		ret = f2fs_dquot_initialize(inode);
 		if (ret) {
 			iput(inode);
 			return ret;
@@ -595,7 +604,7 @@
 
 	f2fs_wait_on_page_writeback(dn.node_page, NODE, true, true);
 
-	err = f2fs_get_node_info(sbi, dn.nid, &ni);
+	err = f2fs_get_node_info(sbi, dn.nid, &ni, false);
 	if (err)
 		goto err;
 
@@ -648,7 +657,16 @@
 		 */
 		if (dest == NEW_ADDR) {
 			f2fs_truncate_data_blocks_range(&dn, 1);
-			f2fs_reserve_new_block(&dn);
+			do {
+				err = f2fs_reserve_new_block(&dn);
+				if (err == -ENOSPC) {
+					f2fs_bug_on(sbi, 1);
+					break;
+				}
+			} while (err &&
+				IS_ENABLED(CONFIG_F2FS_FAULT_INJECTION));
+			if (err)
+				goto err;
 			continue;
 		}
 
@@ -656,12 +674,14 @@
 		if (f2fs_is_valid_blkaddr(sbi, dest, META_POR)) {
 
 			if (src == NULL_ADDR) {
-				err = f2fs_reserve_new_block(&dn);
-				while (err &&
-				       IS_ENABLED(CONFIG_F2FS_FAULT_INJECTION))
+				do {
 					err = f2fs_reserve_new_block(&dn);
-				/* We should not get -ENOSPC */
-				f2fs_bug_on(sbi, err);
+					if (err == -ENOSPC) {
+						f2fs_bug_on(sbi, 1);
+						break;
+					}
+				} while (err &&
+					IS_ENABLED(CONFIG_F2FS_FAULT_INJECTION));
 				if (err)
 					goto err;
 			}
@@ -677,6 +697,14 @@
 				goto err;
 			}
 
+			if (f2fs_is_valid_blkaddr(sbi, dest,
+					DATA_GENERIC_ENHANCE_UPDATE)) {
+				f2fs_err(sbi, "Inconsistent dest blkaddr:%u, ino:%lu, ofs:%u",
+					dest, inode->i_ino, dn.ofs_in_node);
+				err = -EFSCORRUPTED;
+				goto err;
+			}
+
 			/* write dummy data page */
 			f2fs_replace_block(sbi, &dn, src, dest,
 						ni.version, false, false);
@@ -843,6 +871,8 @@
 	if (!err && fix_curseg_write_pointer && !f2fs_readonly(sbi->sb) &&
 			f2fs_sb_has_blkzoned(sbi)) {
 		err = f2fs_fix_curseg_write_pointer(sbi);
+		if (!err)
+			err = f2fs_check_write_pointer(sbi);
 		ret = err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/segment.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/segment.c
@@ -253,7 +253,7 @@
 				goto next;
 			}
 
-			err = f2fs_get_node_info(sbi, dn.nid, &ni);
+			err = f2fs_get_node_info(sbi, dn.nid, &ni, false);
 			if (err) {
 				f2fs_put_dnode(&dn);
 				return err;
@@ -313,8 +313,7 @@
 skip:
 		iput(inode);
 	}
-	congestion_wait(BLK_RW_ASYNC, DEFAULT_IO_TIMEOUT);
-	cond_resched();
+	f2fs_io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 	if (gc_failure) {
 		if (++looped >= count)
 			return;
@@ -356,16 +355,19 @@
 	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	struct list_head *head = &fi->inmem_pages;
 	struct inmem_pages *cur = NULL;
+	struct inmem_pages *tmp;
 
 	f2fs_bug_on(sbi, !page_private_atomic(page));
 
 	mutex_lock(&fi->inmem_lock);
-	list_for_each_entry(cur, head, list) {
-		if (cur->page == page)
+	list_for_each_entry(tmp, head, list) {
+		if (tmp->page == page) {
+			cur = tmp;
 			break;
+		}
 	}
 
-	f2fs_bug_on(sbi, list_empty(head) || cur->page != page);
+	f2fs_bug_on(sbi, !cur);
 	list_del(&cur->list);
 	mutex_unlock(&fi->inmem_lock);
 
@@ -561,7 +563,7 @@
 		goto do_sync;
 
 	/* checkpoint is the only way to shrink partial cached entries */
-	if (f2fs_available_free_memory(sbi, NAT_ENTRIES) ||
+	if (f2fs_available_free_memory(sbi, NAT_ENTRIES) &&
 		f2fs_available_free_memory(sbi, INO_ENTRIES))
 		return;
 
@@ -572,7 +574,7 @@
 		mutex_lock(&sbi->flush_lock);
 
 		blk_start_plug(&plug);
-		f2fs_sync_dirty_inodes(sbi, FILE_INODE);
+		f2fs_sync_dirty_inodes(sbi, FILE_INODE, false);
 		blk_finish_plug(&plug);
 
 		mutex_unlock(&sbi->flush_lock);
@@ -786,8 +788,7 @@
 		do {
 			ret = __submit_flush_wait(sbi, FDEV(i).bdev);
 			if (ret)
-				congestion_wait(BLK_RW_ASYNC,
-						DEFAULT_IO_TIMEOUT);
+				f2fs_io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 		} while (ret && --count);
 
 		if (ret) {
@@ -1548,7 +1549,7 @@
 		if (i + 1 < dpolicy->granularity)
 			break;
 
-		if (i < DEFAULT_DISCARD_GRANULARITY && dpolicy->ordered)
+		if (i + 1 < DEFAULT_DISCARD_GRANULARITY && dpolicy->ordered)
 			return __issue_discard_cmd_orderly(sbi, dpolicy);
 
 		pend_list = &dcc->pend_list[i];
@@ -2126,8 +2127,10 @@
 
 	dcc->f2fs_issue_discard = kthread_run(issue_discard_thread, sbi,
 				"f2fs_discard-%u:%u", MAJOR(dev), MINOR(dev));
-	if (IS_ERR(dcc->f2fs_issue_discard))
+	if (IS_ERR(dcc->f2fs_issue_discard)) {
 		err = PTR_ERR(dcc->f2fs_issue_discard);
+		dcc->f2fs_issue_discard = NULL;
+	}
 
 	return err;
 }
@@ -2266,6 +2269,8 @@
 #endif
 
 	segno = GET_SEGNO(sbi, blkaddr);
+	if (segno == NULL_SEGNO)
+		return;
 
 	se = get_seg_entry(sbi, segno);
 	new_vblocks = se->valid_blocks + del;
@@ -2724,7 +2729,7 @@
  * This function always allocates a used segment(from dirty seglist) by SSR
  * manner, so it should recover the existing segment information of valid blocks
  */
-static void change_curseg(struct f2fs_sb_info *sbi, int type, bool flush)
+static void change_curseg(struct f2fs_sb_info *sbi, int type)
 {
 	struct dirty_seglist_info *dirty_i = DIRTY_I(sbi);
 	struct curseg_info *curseg = CURSEG_I(sbi, type);
@@ -2732,9 +2737,8 @@
 	struct f2fs_summary_block *sum_node;
 	struct page *sum_page;
 
-	if (flush)
-		write_sum_page(sbi, curseg->sum_blk,
-					GET_SUM_BLOCK(sbi, curseg->segno));
+	if (curseg->inited)
+		write_sum_page(sbi, curseg->sum_blk, GET_SUM_BLOCK(sbi, curseg->segno));
 
 	__set_test_and_inuse(sbi, new_segno);
 
@@ -2773,7 +2777,7 @@
 		struct seg_entry *se = get_seg_entry(sbi, curseg->next_segno);
 
 		curseg->seg_type = se->type;
-		change_curseg(sbi, type, true);
+		change_curseg(sbi, type);
 	} else {
 		/* allocate cold segment by default */
 		curseg->seg_type = CURSEG_COLD_DATA;
@@ -2917,31 +2921,20 @@
 	return 0;
 }
 
-/*
- * flush out current segment and replace it with new segment
- * This function should be returned with success, otherwise BUG
- */
-static void allocate_segment_by_default(struct f2fs_sb_info *sbi,
-						int type, bool force)
+static bool need_new_seg(struct f2fs_sb_info *sbi, int type)
 {
 	struct curseg_info *curseg = CURSEG_I(sbi, type);
 
-	if (force)
-		new_curseg(sbi, type, true);
-	else if (!is_set_ckpt_flags(sbi, CP_CRC_RECOVERY_FLAG) &&
-					curseg->seg_type == CURSEG_WARM_NODE)
-		new_curseg(sbi, type, false);
-	else if (curseg->alloc_type == LFS &&
-			is_next_segment_free(sbi, curseg, type) &&
-			likely(!is_sbi_flag_set(sbi, SBI_CP_DISABLED)))
-		new_curseg(sbi, type, false);
-	else if (f2fs_need_SSR(sbi) &&
-			get_ssr_segment(sbi, type, SSR, 0))
-		change_curseg(sbi, type, true);
-	else
-		new_curseg(sbi, type, false);
-
-	stat_inc_seg_type(sbi, curseg);
+	if (!is_set_ckpt_flags(sbi, CP_CRC_RECOVERY_FLAG) &&
+	    curseg->seg_type == CURSEG_WARM_NODE)
+		return true;
+	if (curseg->alloc_type == LFS &&
+	    is_next_segment_free(sbi, curseg, type) &&
+	    likely(!is_sbi_flag_set(sbi, SBI_CP_DISABLED)))
+		return true;
+	if (!f2fs_need_SSR(sbi) || !get_ssr_segment(sbi, type, SSR, 0))
+		return true;
+	return false;
 }
 
 void f2fs_allocate_segment_for_resize(struct f2fs_sb_info *sbi, int type,
@@ -2959,7 +2952,7 @@
 		goto unlock;
 
 	if (f2fs_need_SSR(sbi) && get_ssr_segment(sbi, type, SSR, 0))
-		change_curseg(sbi, type, true);
+		change_curseg(sbi, type);
 	else
 		new_curseg(sbi, type, true);
 
@@ -2994,7 +2987,8 @@
 		return;
 alloc:
 	old_segno = curseg->segno;
-	SIT_I(sbi)->s_ops->allocate_segment(sbi, type, true);
+	new_curseg(sbi, type, true);
+	stat_inc_seg_type(sbi, curseg);
 	locate_dirty_segment(sbi, old_segno);
 }
 
@@ -3025,10 +3019,6 @@
 	up_read(&SM_I(sbi)->curseg_lock);
 }
 
-static const struct segment_allocation default_salloc_ops = {
-	.allocate_segment = allocate_segment_by_default,
-};
-
 bool f2fs_exist_trim_candidates(struct f2fs_sb_info *sbi,
 						struct cp_control *cpc)
 {
@@ -3101,7 +3091,7 @@
 			blk_finish_plug(&plug);
 			mutex_unlock(&dcc->cmd_lock);
 			trimmed += __wait_all_discard_cmd(sbi, NULL);
-			congestion_wait(BLK_RW_ASYNC, DEFAULT_IO_TIMEOUT);
+			f2fs_io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 			goto next;
 		}
 skip:
@@ -3440,15 +3430,22 @@
 	 * since SSR needs latest valid block information.
 	 */
 	update_sit_entry(sbi, *new_blkaddr, 1);
-	if (GET_SEGNO(sbi, old_blkaddr) != NULL_SEGNO)
-		update_sit_entry(sbi, old_blkaddr, -1);
+	update_sit_entry(sbi, old_blkaddr, -1);
 
 	if (!__has_curseg_space(sbi, curseg)) {
-		if (from_gc)
+		/*
+		 * Flush out current segment and replace it with new segment.
+		 */
+		if (from_gc) {
 			get_atssr_segment(sbi, type, se->type,
 						AT_SSR, se->mtime);
-		else
-			sit_i->s_ops->allocate_segment(sbi, type, false);
+		} else {
+			if (need_new_seg(sbi, type))
+				new_curseg(sbi, type, false);
+			else
+				change_curseg(sbi, type);
+			stat_inc_seg_type(sbi, curseg);
+		}
 	}
 	/*
 	 * segment dirty status should be updated after segment allocation,
@@ -3470,10 +3467,10 @@
 		struct f2fs_bio_info *io;
 
 		if (F2FS_IO_ALIGNED(sbi))
-			fio->retry = false;
+			fio->retry = 0;
 
 		INIT_LIST_HEAD(&fio->list);
-		fio->in_list = true;
+		fio->in_list = 1;
 		io = sbi->write_io[fio->type] + fio->temp;
 		spin_lock(&io->io_lock);
 		list_add_tail(&fio->list, &io->io_list);
@@ -3485,24 +3482,30 @@
 	up_read(&SM_I(sbi)->curseg_lock);
 }
 
-static void update_device_state(struct f2fs_io_info *fio)
+void f2fs_update_device_state(struct f2fs_sb_info *sbi, nid_t ino,
+					block_t blkaddr, unsigned int blkcnt)
 {
-	struct f2fs_sb_info *sbi = fio->sbi;
-	unsigned int devidx;
-
 	if (!f2fs_is_multi_device(sbi))
 		return;
 
-	devidx = f2fs_target_device_index(sbi, fio->new_blkaddr);
+	while (1) {
+		unsigned int devidx = f2fs_target_device_index(sbi, blkaddr);
+		unsigned int blks = FDEV(devidx).end_blk - blkaddr + 1;
 
-	/* update device state for fsync */
-	f2fs_set_dirty_device(sbi, fio->ino, devidx, FLUSH_INO);
+		/* update device state for fsync */
+		f2fs_set_dirty_device(sbi, ino, devidx, FLUSH_INO);
 
-	/* update device state for checkpoint */
-	if (!f2fs_test_bit(devidx, (char *)&sbi->dirty_device)) {
-		spin_lock(&sbi->dev_lock);
-		f2fs_set_bit(devidx, (char *)&sbi->dirty_device);
-		spin_unlock(&sbi->dev_lock);
+		/* update device state for checkpoint */
+		if (!f2fs_test_bit(devidx, (char *)&sbi->dirty_device)) {
+			spin_lock(&sbi->dev_lock);
+			f2fs_set_bit(devidx, (char *)&sbi->dirty_device);
+			spin_unlock(&sbi->dev_lock);
+		}
+
+		if (blkcnt <= blks)
+			break;
+		blkcnt -= blks;
+		blkaddr += blks;
 	}
 }
 
@@ -3529,7 +3532,7 @@
 		goto reallocate;
 	}
 
-	update_device_state(fio);
+	f2fs_update_device_state(fio->sbi, fio->ino, fio->new_blkaddr, 1);
 
 	if (keep_order)
 		up_read(&fio->sbi->io_order_lock);
@@ -3548,7 +3551,7 @@
 		.new_blkaddr = page->index,
 		.page = page,
 		.encrypted_page = NULL,
-		.in_list = false,
+		.in_list = 0,
 	};
 
 	if (unlikely(page->index >= MAIN_BLKADDR(sbi)))
@@ -3611,6 +3614,10 @@
 		goto drop_bio;
 	}
 
+	if (fio->post_read)
+		invalidate_mapping_pages(META_MAPPING(sbi),
+				fio->new_blkaddr, fio->new_blkaddr);
+
 	stat_inc_inplace_blocks(fio->sbi);
 
 	if (fio->bio && !(SM_I(sbi)->ipu_policy & (1 << F2FS_IPU_NOCACHE)))
@@ -3618,7 +3625,8 @@
 	else
 		err = f2fs_submit_page_bio(fio);
 	if (!err) {
-		update_device_state(fio);
+		f2fs_update_device_state(fio->sbi, fio->ino,
+						fio->new_blkaddr, 1);
 		f2fs_update_iostat(fio->sbi, fio->io_type, F2FS_BLKSIZE);
 	}
 
@@ -3683,8 +3691,8 @@
 		}
 	}
 
-	f2fs_bug_on(sbi, !IS_DATASEG(type));
 	curseg = CURSEG_I(sbi, type);
+	f2fs_bug_on(sbi, !IS_DATASEG(curseg->seg_type));
 
 	mutex_lock(&curseg->curseg_mutex);
 	down_write(&sit_i->sentry_lock);
@@ -3696,7 +3704,7 @@
 	/* change the current segment */
 	if (segno != curseg->segno) {
 		curseg->next_segno = segno;
-		change_curseg(sbi, type, true);
+		change_curseg(sbi, type);
 	}
 
 	curseg->next_blkoff = GET_BLKOFF_FROM_SEG0(sbi, new_blkaddr);
@@ -3724,7 +3732,7 @@
 	if (recover_curseg) {
 		if (old_cursegno != curseg->segno) {
 			curseg->next_segno = old_cursegno;
-			change_curseg(sbi, type, true);
+			change_curseg(sbi, type);
 		}
 		curseg->next_blkoff = old_blkoff;
 		curseg->alloc_type = old_alloc_type;
@@ -3758,7 +3766,7 @@
 
 		/* submit cached LFS IO */
 		f2fs_submit_merged_write_cond(sbi, NULL, page, 0, type);
-		/* sbumit cached IPU IO */
+		/* submit cached IPU IO */
 		f2fs_submit_merged_ipu_write(sbi, NULL, page);
 		if (ordered) {
 			wait_on_page_writeback(page);
@@ -3790,10 +3798,16 @@
 void f2fs_wait_on_block_writeback_range(struct inode *inode, block_t blkaddr,
 								block_t len)
 {
+	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	block_t i;
 
+	if (!f2fs_post_read_required(inode))
+		return;
+
 	for (i = 0; i < len; i++)
 		f2fs_wait_on_block_writeback(inode, blkaddr + i);
+
+	invalidate_mapping_pages(META_MAPPING(sbi), blkaddr, blkaddr + len - 1);
 }
 
 static int read_compacted_summaries(struct f2fs_sb_info *sbi)
@@ -4413,9 +4427,6 @@
 		return -ENOMEM;
 #endif
 
-	/* init SIT information */
-	sit_i->s_ops = &default_salloc_ops;
-
 	sit_i->sit_base_addr = le32_to_cpu(raw_super->sit_blkaddr);
 	sit_i->sit_blocks = sit_segs << sbi->log_blocks_per_seg;
 	sit_i->written_valid_blocks = 0;
@@ -4508,7 +4519,7 @@
 	unsigned int i, start, end;
 	unsigned int readed, start_blk = 0;
 	int err = 0;
-	block_t total_node_blocks = 0;
+	block_t sit_valid_blocks[2] = {0, 0};
 
 	do {
 		readed = f2fs_ra_meta_pages(sbi, start_blk, BIO_MAX_VECS,
@@ -4533,8 +4544,14 @@
 			if (err)
 				return err;
 			seg_info_from_raw_sit(se, &sit);
-			if (IS_NODESEG(se->type))
-				total_node_blocks += se->valid_blocks;
+
+			if (se->type >= NR_PERSISTENT_LOG) {
+				f2fs_err(sbi, "Invalid segment type: %u, segno: %u",
+							se->type, start);
+				return -EFSCORRUPTED;
+			}
+
+			sit_valid_blocks[SE_PAGETYPE(se)] += se->valid_blocks;
 
 			if (f2fs_block_unit_discard(sbi)) {
 				/* build discard map only one time */
@@ -4574,15 +4591,22 @@
 		sit = sit_in_journal(journal, i);
 
 		old_valid_blocks = se->valid_blocks;
-		if (IS_NODESEG(se->type))
-			total_node_blocks -= old_valid_blocks;
+
+		sit_valid_blocks[SE_PAGETYPE(se)] -= old_valid_blocks;
 
 		err = check_block_count(sbi, start, &sit);
 		if (err)
 			break;
 		seg_info_from_raw_sit(se, &sit);
-		if (IS_NODESEG(se->type))
-			total_node_blocks += se->valid_blocks;
+
+		if (se->type >= NR_PERSISTENT_LOG) {
+			f2fs_err(sbi, "Invalid segment type: %u, segno: %u",
+							se->type, start);
+			err = -EFSCORRUPTED;
+			break;
+		}
+
+		sit_valid_blocks[SE_PAGETYPE(se)] += se->valid_blocks;
 
 		if (f2fs_block_unit_discard(sbi)) {
 			if (is_set_ckpt_flags(sbi, CP_TRIMMED_FLAG)) {
@@ -4604,13 +4628,24 @@
 	}
 	up_read(&curseg->journal_rwsem);
 
-	if (!err && total_node_blocks != valid_node_count(sbi)) {
+	if (err)
+		return err;
+
+	if (sit_valid_blocks[NODE] != valid_node_count(sbi)) {
 		f2fs_err(sbi, "SIT is corrupted node# %u vs %u",
-			 total_node_blocks, valid_node_count(sbi));
-		err = -EFSCORRUPTED;
+			 sit_valid_blocks[NODE], valid_node_count(sbi));
+		return -EFSCORRUPTED;
 	}
 
-	return err;
+	if (sit_valid_blocks[DATA] + sit_valid_blocks[NODE] >
+				valid_user_blocks(sbi)) {
+		f2fs_err(sbi, "SIT is corrupted data# %u %u vs %u",
+			 sit_valid_blocks[DATA], sit_valid_blocks[NODE],
+			 valid_user_blocks(sbi));
+		return -EFSCORRUPTED;
+	}
+
+	return 0;
 }
 
 static void init_free_segmap(struct f2fs_sb_info *sbi)
@@ -4747,6 +4782,13 @@
 
 		sanity_check_seg_type(sbi, curseg->seg_type);
 
+		if (curseg->alloc_type != LFS && curseg->alloc_type != SSR) {
+			f2fs_err(sbi,
+				 "Current segment has invalid alloc_type:%d",
+				 curseg->alloc_type);
+			return -EFSCORRUPTED;
+		}
+
 		if (f2fs_test_bit(blkofs, se->cur_valid_map))
 			goto out;
 
@@ -5017,54 +5059,6 @@
 	return 0;
 }
 
-static bool is_conv_zone(struct f2fs_sb_info *sbi, unsigned int zone_idx,
-						unsigned int dev_idx)
-{
-	if (!bdev_is_zoned(FDEV(dev_idx).bdev))
-		return true;
-	return !test_bit(zone_idx, FDEV(dev_idx).blkz_seq);
-}
-
-/* Return the zone index in the given device */
-static unsigned int get_zone_idx(struct f2fs_sb_info *sbi, unsigned int secno,
-					int dev_idx)
-{
-	block_t sec_start_blkaddr = START_BLOCK(sbi, GET_SEG_FROM_SEC(sbi, secno));
-
-	return (sec_start_blkaddr - FDEV(dev_idx).start_blk) >>
-						sbi->log_blocks_per_blkz;
-}
-
-/*
- * Return the usable segments in a section based on the zone's
- * corresponding zone capacity. Zone is equal to a section.
- */
-static inline unsigned int f2fs_usable_zone_segs_in_sec(
-		struct f2fs_sb_info *sbi, unsigned int segno)
-{
-	unsigned int dev_idx, zone_idx, unusable_segs_in_sec;
-
-	dev_idx = f2fs_target_device_index(sbi, START_BLOCK(sbi, segno));
-	zone_idx = get_zone_idx(sbi, GET_SEC_FROM_SEG(sbi, segno), dev_idx);
-
-	/* Conventional zone's capacity is always equal to zone size */
-	if (is_conv_zone(sbi, zone_idx, dev_idx))
-		return sbi->segs_per_sec;
-
-	/*
-	 * If the zone_capacity_blocks array is NULL, then zone capacity
-	 * is equal to the zone size for all zones
-	 */
-	if (!FDEV(dev_idx).zone_capacity_blocks)
-		return sbi->segs_per_sec;
-
-	/* Get the segment count beyond zone capacity block */
-	unusable_segs_in_sec = (sbi->blocks_per_blkz -
-				FDEV(dev_idx).zone_capacity_blocks[zone_idx]) >>
-				sbi->log_blocks_per_seg;
-	return sbi->segs_per_sec - unusable_segs_in_sec;
-}
-
 /*
  * Return the number of usable blocks in a segment. The number of blocks
  * returned is always equal to the number of blocks in a segment for
@@ -5077,26 +5071,15 @@
 			struct f2fs_sb_info *sbi, unsigned int segno)
 {
 	block_t seg_start, sec_start_blkaddr, sec_cap_blkaddr;
-	unsigned int zone_idx, dev_idx, secno;
+	unsigned int secno;
 
-	secno = GET_SEC_FROM_SEG(sbi, segno);
-	seg_start = START_BLOCK(sbi, segno);
-	dev_idx = f2fs_target_device_index(sbi, seg_start);
-	zone_idx = get_zone_idx(sbi, secno, dev_idx);
-
-	/*
-	 * Conventional zone's capacity is always equal to zone size,
-	 * so, blocks per segment is unchanged.
-	 */
-	if (is_conv_zone(sbi, zone_idx, dev_idx))
-		return sbi->blocks_per_seg;
-
-	if (!FDEV(dev_idx).zone_capacity_blocks)
+	if (!sbi->unusable_blocks_per_sec)
 		return sbi->blocks_per_seg;
 
+	secno = GET_SEC_FROM_SEG(sbi, segno);
+	seg_start = START_BLOCK(sbi, segno);
 	sec_start_blkaddr = START_BLOCK(sbi, GET_SEG_FROM_SEC(sbi, secno));
-	sec_cap_blkaddr = sec_start_blkaddr +
-				FDEV(dev_idx).zone_capacity_blocks[zone_idx];
+	sec_cap_blkaddr = sec_start_blkaddr + CAP_BLKS_PER_SEC(sbi);
 
 	/*
 	 * If segment starts before zone capacity and spans beyond
@@ -5128,11 +5111,6 @@
 	return 0;
 }
 
-static inline unsigned int f2fs_usable_zone_segs_in_sec(struct f2fs_sb_info *sbi,
-							unsigned int segno)
-{
-	return 0;
-}
 #endif
 unsigned int f2fs_usable_blks_in_seg(struct f2fs_sb_info *sbi,
 					unsigned int segno)
@@ -5147,7 +5125,7 @@
 					unsigned int segno)
 {
 	if (f2fs_sb_has_blkzoned(sbi))
-		return f2fs_usable_zone_segs_in_sec(sbi, segno);
+		return CAP_SEGS_PER_SEC(sbi);
 
 	return sbi->segs_per_sec;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/segment.h
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/segment.h
@@ -24,6 +24,7 @@
 
 #define IS_DATASEG(t)	((t) <= CURSEG_COLD_DATA)
 #define IS_NODESEG(t)	((t) >= CURSEG_HOT_NODE && (t) <= CURSEG_COLD_NODE)
+#define SE_PAGETYPE(se)	((IS_NODESEG((se)->type) ? NODE : DATA))
 
 static inline void sanity_check_seg_type(struct f2fs_sb_info *sbi,
 						unsigned short seg_type)
@@ -100,6 +101,12 @@
 		GET_SEGNO_FROM_SEG0(sbi, blk_addr)))
 #define BLKS_PER_SEC(sbi)					\
 	((sbi)->segs_per_sec * (sbi)->blocks_per_seg)
+#define CAP_BLKS_PER_SEC(sbi)					\
+	((sbi)->segs_per_sec * (sbi)->blocks_per_seg -		\
+	 (sbi)->unusable_blocks_per_sec)
+#define CAP_SEGS_PER_SEC(sbi)					\
+	((sbi)->segs_per_sec - ((sbi)->unusable_blocks_per_sec >>\
+	(sbi)->log_blocks_per_seg))
 #define GET_SEC_FROM_SEG(sbi, segno)				\
 	(((segno) == -1) ? -1: (segno) / (sbi)->segs_per_sec)
 #define GET_SEG_FROM_SEC(sbi, secno)				\
@@ -218,10 +225,6 @@
 	unsigned int valid_blocks;	/* # of valid blocks in a section */
 };
 
-struct segment_allocation {
-	void (*allocate_segment)(struct f2fs_sb_info *, int, bool);
-};
-
 #define MAX_SKIP_GC_COUNT			16
 
 struct inmem_pages {
@@ -231,8 +234,6 @@
 };
 
 struct sit_info {
-	const struct segment_allocation *s_ops;
-
 	block_t sit_base_addr;		/* start block address of SIT area */
 	block_t sit_blocks;		/* # of blocks used by SIT area */
 	block_t written_valid_blocks;	/* # of valid blocks in main area */
@@ -537,7 +538,8 @@
 
 static inline unsigned int reserved_segments(struct f2fs_sb_info *sbi)
 {
-	return SM_I(sbi)->reserved_segments;
+	return SM_I(sbi)->reserved_segments +
+			SM_I(sbi)->additional_reserved_segments;
 }
 
 static inline unsigned int free_sections(struct f2fs_sb_info *sbi)
@@ -570,11 +572,10 @@
 	return GET_SEC_FROM_SEG(sbi, reserved_segments(sbi));
 }
 
-static inline bool has_curseg_enough_space(struct f2fs_sb_info *sbi)
+static inline bool has_curseg_enough_space(struct f2fs_sb_info *sbi,
+			unsigned int node_blocks, unsigned int dent_blocks)
 {
-	unsigned int node_blocks = get_pages(sbi, F2FS_DIRTY_NODES) +
-					get_pages(sbi, F2FS_DIRTY_DENTS);
-	unsigned int dent_blocks = get_pages(sbi, F2FS_DIRTY_DENTS);
+
 	unsigned int segno, left_blocks;
 	int i;
 
@@ -600,19 +601,28 @@
 static inline bool has_not_enough_free_secs(struct f2fs_sb_info *sbi,
 					int freed, int needed)
 {
-	int node_secs = get_blocktype_secs(sbi, F2FS_DIRTY_NODES);
-	int dent_secs = get_blocktype_secs(sbi, F2FS_DIRTY_DENTS);
-	int imeta_secs = get_blocktype_secs(sbi, F2FS_DIRTY_IMETA);
+	unsigned int total_node_blocks = get_pages(sbi, F2FS_DIRTY_NODES) +
+					get_pages(sbi, F2FS_DIRTY_DENTS) +
+					get_pages(sbi, F2FS_DIRTY_IMETA);
+	unsigned int total_dent_blocks = get_pages(sbi, F2FS_DIRTY_DENTS);
+	unsigned int node_secs = total_node_blocks / BLKS_PER_SEC(sbi);
+	unsigned int dent_secs = total_dent_blocks / BLKS_PER_SEC(sbi);
+	unsigned int node_blocks = total_node_blocks % BLKS_PER_SEC(sbi);
+	unsigned int dent_blocks = total_dent_blocks % BLKS_PER_SEC(sbi);
+	unsigned int free, need_lower, need_upper;
 
 	if (unlikely(is_sbi_flag_set(sbi, SBI_POR_DOING)))
 		return false;
 
-	if (free_sections(sbi) + freed == reserved_sections(sbi) + needed &&
-			has_curseg_enough_space(sbi))
+	free = free_sections(sbi) + freed;
+	need_lower = node_secs + dent_secs + reserved_sections(sbi) + needed;
+	need_upper = need_lower + (node_blocks ? 1 : 0) + (dent_blocks ? 1 : 0);
+
+	if (free > need_upper)
 		return false;
-	return (free_sections(sbi) + freed) <=
-		(node_secs + 2 * dent_secs + imeta_secs +
-		reserved_sections(sbi) + needed);
+	else if (free <= need_lower)
+		return true;
+	return !has_curseg_enough_space(sbi, node_blocks, dent_blocks);
 }
 
 static inline bool f2fs_is_checkpoint_ready(struct f2fs_sb_info *sbi)
@@ -649,7 +659,9 @@
  *                     pages over min_fsync_blocks. (=default option)
  * F2FS_IPU_ASYNC - do IPU given by asynchronous write requests.
  * F2FS_IPU_NOCACHE - disable IPU bio cache.
- * F2FS_IPUT_DISABLE - disable IPU. (=default option in LFS mode)
+ * F2FS_IPU_HONOR_OPU_WRITE - use OPU write prior to IPU write if inode has
+ *                            FI_OPU_WRITE flag.
+ * F2FS_IPU_DISABLE - disable IPU. (=default option in LFS mode)
  */
 #define DEF_MIN_IPU_UTIL	70
 #define DEF_MIN_FSYNC_BLOCKS	8
@@ -665,6 +677,7 @@
 	F2FS_IPU_FSYNC,
 	F2FS_IPU_ASYNC,
 	F2FS_IPU_NOCACHE,
+	F2FS_IPU_HONOR_OPU_WRITE,
 };
 
 static inline unsigned int curseg_segno(struct f2fs_sb_info *sbi,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/super.c
@@ -58,23 +58,34 @@
 	[FAULT_DISCARD]		= "discard error",
 	[FAULT_WRITE_IO]	= "write IO error",
 	[FAULT_SLAB_ALLOC]	= "slab alloc",
+	[FAULT_DQUOT_INIT]	= "dquot initialize",
 };
 
-void f2fs_build_fault_attr(struct f2fs_sb_info *sbi, unsigned int rate,
-							unsigned int type)
+int f2fs_build_fault_attr(struct f2fs_sb_info *sbi, unsigned long rate,
+							unsigned long type)
 {
 	struct f2fs_fault_info *ffi = &F2FS_OPTION(sbi).fault_info;
 
 	if (rate) {
+		if (rate > INT_MAX)
+			return -EINVAL;
 		atomic_set(&ffi->inject_ops, 0);
-		ffi->inject_rate = rate;
+		ffi->inject_rate = (int)rate;
 	}
 
-	if (type)
-		ffi->inject_type = type;
+	if (type) {
+		if (type >= (1 << FAULT_MAX))
+			return -EINVAL;
+		ffi->inject_type = (unsigned int)type;
+	}
 
 	if (!rate && !type)
 		memset(ffi, 0, sizeof(struct f2fs_fault_info));
+	else
+		f2fs_info(sbi,
+			"build fault injection attr: rate: %lu, type: 0x%lx",
+								rate, type);
+	return 0;
 }
 #endif
 
@@ -305,10 +316,10 @@
 
 static inline void limit_reserve_root(struct f2fs_sb_info *sbi)
 {
-	block_t limit = min((sbi->user_block_count << 1) / 1000,
+	block_t limit = min((sbi->user_block_count >> 3),
 			sbi->user_block_count - sbi->reserved_blocks);
 
-	/* limit is 0.2% */
+	/* limit is 12.5% */
 	if (test_opt(sbi, RESERVE_ROOT) &&
 			F2FS_OPTION(sbi).root_reserved_blocks > limit) {
 		F2FS_OPTION(sbi).root_reserved_blocks = limit;
@@ -327,6 +338,46 @@
 					   F2FS_OPTION(sbi).s_resgid));
 }
 
+static inline int adjust_reserved_segment(struct f2fs_sb_info *sbi)
+{
+	unsigned int sec_blks = sbi->blocks_per_seg * sbi->segs_per_sec;
+	unsigned int avg_vblocks;
+	unsigned int wanted_reserved_segments;
+	block_t avail_user_block_count;
+
+	if (!F2FS_IO_ALIGNED(sbi))
+		return 0;
+
+	/* average valid block count in section in worst case */
+	avg_vblocks = sec_blks / F2FS_IO_SIZE(sbi);
+
+	/*
+	 * we need enough free space when migrating one section in worst case
+	 */
+	wanted_reserved_segments = (F2FS_IO_SIZE(sbi) / avg_vblocks) *
+						reserved_segments(sbi);
+	wanted_reserved_segments -= reserved_segments(sbi);
+
+	avail_user_block_count = sbi->user_block_count -
+				sbi->current_reserved_blocks -
+				F2FS_OPTION(sbi).root_reserved_blocks;
+
+	if (wanted_reserved_segments * sbi->blocks_per_seg >
+					avail_user_block_count) {
+		f2fs_err(sbi, "IO align feature can't grab additional reserved segment: %u, available segments: %u",
+			wanted_reserved_segments,
+			avail_user_block_count >> sbi->log_blocks_per_seg);
+		return -ENOSPC;
+	}
+
+	SM_I(sbi)->additional_reserved_segments = wanted_reserved_segments;
+
+	f2fs_info(sbi, "IO align feature needs additional reserved segment: %u",
+			 wanted_reserved_segments);
+
+	return 0;
+}
+
 static inline void adjust_unusable_cap_perc(struct f2fs_sb_info *sbi)
 {
 	if (!F2FS_OPTION(sbi).unusable_cap_perc)
@@ -499,6 +550,29 @@
 }
 
 #ifdef CONFIG_F2FS_FS_COMPRESSION
+static bool is_compress_extension_exist(struct f2fs_sb_info *sbi,
+					const char *new_ext, bool is_ext)
+{
+	unsigned char (*ext)[F2FS_EXTENSION_LEN];
+	int ext_cnt;
+	int i;
+
+	if (is_ext) {
+		ext = F2FS_OPTION(sbi).extensions;
+		ext_cnt = F2FS_OPTION(sbi).compress_ext_cnt;
+	} else {
+		ext = F2FS_OPTION(sbi).noextensions;
+		ext_cnt = F2FS_OPTION(sbi).nocompress_ext_cnt;
+	}
+
+	for (i = 0; i < ext_cnt; i++) {
+		if (!strcasecmp(new_ext, ext[i]))
+			return true;
+	}
+
+	return false;
+}
+
 /*
  * 1. The same extension name cannot not appear in both compress and non-compress extension
  * at the same time.
@@ -837,14 +911,17 @@
 		case Opt_fault_injection:
 			if (args->from && match_int(args, &arg))
 				return -EINVAL;
-			f2fs_build_fault_attr(sbi, arg, F2FS_ALL_FAULT_TYPE);
+			if (f2fs_build_fault_attr(sbi, arg,
+					F2FS_ALL_FAULT_TYPE))
+				return -EINVAL;
 			set_opt(sbi, FAULT_INJECTION);
 			break;
 
 		case Opt_fault_type:
 			if (args->from && match_int(args, &arg))
 				return -EINVAL;
-			f2fs_build_fault_attr(sbi, 0, arg);
+			if (f2fs_build_fault_attr(sbi, 0, arg))
+				return -EINVAL;
 			set_opt(sbi, FAULT_INJECTION);
 			break;
 #else
@@ -1113,6 +1190,11 @@
 				return -EINVAL;
 			}
 
+			if (is_compress_extension_exist(sbi, name, true)) {
+				kfree(name);
+				break;
+			}
+
 			strcpy(ext[ext_cnt], name);
 			F2FS_OPTION(sbi).compress_ext_cnt++;
 			kfree(name);
@@ -1137,6 +1219,11 @@
 				return -EINVAL;
 			}
 
+			if (is_compress_extension_exist(sbi, name, false)) {
+				kfree(name);
+				break;
+			}
+
 			strcpy(noext[noext_cnt], name);
 			F2FS_OPTION(sbi).nocompress_ext_cnt++;
 			kfree(name);
@@ -1292,7 +1379,7 @@
 	/* Not pass down write hints if the number of active logs is lesser
 	 * than NR_CURSEG_PERSIST_TYPE.
 	 */
-	if (F2FS_OPTION(sbi).active_logs != NR_CURSEG_TYPE)
+	if (F2FS_OPTION(sbi).active_logs != NR_CURSEG_PERSIST_TYPE)
 		F2FS_OPTION(sbi).whint_mode = WHINT_MODE_OFF;
 
 	if (f2fs_sb_has_readonly(sbi) && !f2fs_readonly(sbi->sb)) {
@@ -1474,7 +1561,6 @@
 		blkdev_put(FDEV(i).bdev, FMODE_EXCL);
 #ifdef CONFIG_BLK_DEV_ZONED
 		kvfree(FDEV(i).blkz_seq);
-		kfree(FDEV(i).zone_capacity_blocks);
 #endif
 	}
 	kvfree(sbi->devs);
@@ -1620,14 +1706,17 @@
 	if (is_sbi_flag_set(F2FS_SB(sb), SBI_IS_DIRTY))
 		return -EINVAL;
 
-	/* ensure no checkpoint required */
-	if (!llist_empty(&F2FS_SB(sb)->cprc_info.issue_list))
-		return -EINVAL;
+	/* Let's flush checkpoints and stop the thread. */
+	f2fs_flush_ckpt_thread(F2FS_SB(sb));
+
+	/* to avoid deadlock on f2fs_evict_inode->SB_FREEZE_FS */
+	set_sbi_flag(F2FS_SB(sb), SBI_IS_FREEZING);
 	return 0;
 }
 
 static int f2fs_unfreeze(struct super_block *sb)
 {
+	clear_sbi_flag(F2FS_SB(sb), SBI_IS_FREEZING);
 	return 0;
 }
 
@@ -1992,8 +2081,6 @@
 	F2FS_OPTION(sbi).compress_mode = COMPR_MODE_FS;
 	F2FS_OPTION(sbi).bggc_mode = BGGC_MODE_ON;
 
-	sbi->sb->s_flags &= ~SB_INLINECRYPT;
-
 	set_opt(sbi, INLINE_XATTR);
 	set_opt(sbi, INLINE_DATA);
 	set_opt(sbi, INLINE_DENTRY);
@@ -2092,8 +2179,7 @@
 	/* we should flush all the data to keep data consistency */
 	do {
 		sync_inodes_sb(sbi->sb);
-		cond_resched();
-		congestion_wait(BLK_RW_ASYNC, DEFAULT_IO_TIMEOUT);
+		f2fs_io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 	} while (get_pages(sbi, F2FS_DIRTY_DATA) && retry--);
 
 	if (unlikely(retry < 0))
@@ -2107,6 +2193,9 @@
 	up_write(&sbi->gc_lock);
 
 	f2fs_sync_fs(sbi->sb, 1);
+
+	/* Let's ensure there's no pending checkpoint anymore */
+	f2fs_flush_ckpt_thread(sbi);
 }
 
 static int f2fs_remount(struct super_block *sb, int *flags, char *data)
@@ -2179,7 +2268,7 @@
 	if (f2fs_readonly(sb) && (*flags & SB_RDONLY))
 		goto skip;
 
-	if (f2fs_sb_has_readonly(sbi) && !(*flags & SB_RDONLY)) {
+	if (f2fs_dev_is_readonly(sbi) && !(*flags & SB_RDONLY)) {
 		err = -EROFS;
 		goto restore_opts;
 	}
@@ -2273,6 +2362,9 @@
 		f2fs_stop_ckpt_thread(sbi);
 		need_restart_ckpt = true;
 	} else {
+		/* Flush if the prevous checkpoint, if exists. */
+		f2fs_flush_ckpt_thread(sbi);
+
 		err = f2fs_start_ckpt_thread(sbi);
 		if (err) {
 			f2fs_err(sbi,
@@ -2392,7 +2484,6 @@
 	size_t toread;
 	loff_t i_size = i_size_read(inode);
 	struct page *page;
-	char *kaddr;
 
 	if (off > i_size)
 		return 0;
@@ -2426,9 +2517,7 @@
 			return -EIO;
 		}
 
-		kaddr = kmap_atomic(page);
-		memcpy(data, kaddr + offset, tocopy);
-		kunmap_atomic(kaddr);
+		memcpy_from_page(data, page, offset, tocopy);
 		f2fs_put_page(page, 1);
 
 		offset = 0;
@@ -2450,7 +2539,6 @@
 	size_t towrite = len;
 	struct page *page;
 	void *fsdata = NULL;
-	char *kaddr;
 	int err = 0;
 	int tocopy;
 
@@ -2462,18 +2550,14 @@
 							&page, &fsdata);
 		if (unlikely(err)) {
 			if (err == -ENOMEM) {
-				congestion_wait(BLK_RW_ASYNC,
-						DEFAULT_IO_TIMEOUT);
+				f2fs_io_schedule_timeout(DEFAULT_IO_TIMEOUT);
 				goto retry;
 			}
 			set_sbi_flag(F2FS_SB(sb), SBI_QUOTA_NEED_REPAIR);
 			break;
 		}
 
-		kaddr = kmap_atomic(page);
-		memcpy(kaddr + offset, data, tocopy);
-		kunmap_atomic(kaddr);
-		flush_dcache_page(page);
+		memcpy_to_page(page, offset, data, tocopy);
 
 		a_ops->write_end(NULL, mapping, off, tocopy, tocopy,
 						page, fsdata);
@@ -2491,6 +2575,16 @@
 	return len - towrite;
 }
 
+int f2fs_dquot_initialize(struct inode *inode)
+{
+	if (time_to_inject(F2FS_I_SB(inode), FAULT_DQUOT_INIT)) {
+		f2fs_show_injection_info(F2FS_I_SB(inode), FAULT_DQUOT_INIT);
+		return -ESRCH;
+	}
+
+	return dquot_initialize(inode);
+}
+
 static struct dquot **f2fs_get_dquots(struct inode *inode)
 {
 	return F2FS_I(inode)->i_dquot;
@@ -2636,7 +2730,7 @@
 	struct f2fs_sb_info *sbi = F2FS_SB(sb);
 	struct quota_info *dqopt = sb_dqopt(sb);
 	int cnt;
-	int ret;
+	int ret = 0;
 
 	/*
 	 * Now when everything is written we can discard the pagecache so
@@ -2647,10 +2741,11 @@
 		if (type != -1 && cnt != type)
 			continue;
 
-		if (!sb_has_quota_active(sb, type))
-			return 0;
+		if (!sb_has_quota_active(sb, cnt))
+			continue;
 
-		inode_lock(dqopt->files[cnt]);
+		if (!f2fs_sb_has_quota_ino(sbi))
+			inode_lock(dqopt->files[cnt]);
 
 		/*
 		 * do_quotactl
@@ -2669,7 +2764,8 @@
 		up_read(&sbi->quota_sem);
 		f2fs_unlock_op(sbi);
 
-		inode_unlock(dqopt->files[cnt]);
+		if (!f2fs_sb_has_quota_ino(sbi))
+			inode_unlock(dqopt->files[cnt]);
 
 		if (ret)
 			break;
@@ -2875,6 +2971,11 @@
 	.get_nextdqblk	= dquot_get_next_dqblk,
 };
 #else
+int f2fs_dquot_initialize(struct inode *inode)
+{
+	return 0;
+}
+
 int f2fs_quota_sync(struct super_block *sb, int type)
 {
 	return 0;
@@ -3093,9 +3194,9 @@
 	u32 segment_count = le32_to_cpu(raw_super->segment_count);
 	u32 log_blocks_per_seg = le32_to_cpu(raw_super->log_blocks_per_seg);
 	u64 main_end_blkaddr = main_blkaddr +
-				(segment_count_main << log_blocks_per_seg);
+				((u64)segment_count_main << log_blocks_per_seg);
 	u64 seg_end_blkaddr = segment0_blkaddr +
-				(segment_count << log_blocks_per_seg);
+				((u64)segment_count << log_blocks_per_seg);
 
 	if (segment0_blkaddr != cp_blkaddr) {
 		f2fs_info(sbi, "Mismatch start address, segment0(%u) cp_blkaddr(%u)",
@@ -3487,7 +3588,7 @@
 		NR_CURSEG_PERSIST_TYPE + nat_bits_blocks >= blocks_per_seg)) {
 		f2fs_warn(sbi, "Insane cp_payload: %u, nat_bits_blocks: %u)",
 			  cp_payload, nat_bits_blocks);
-		return -EFSCORRUPTED;
+		return 1;
 	}
 
 	if (unlikely(f2fs_cp_error(sbi))) {
@@ -3571,24 +3672,29 @@
 #ifdef CONFIG_BLK_DEV_ZONED
 
 struct f2fs_report_zones_args {
+	struct f2fs_sb_info *sbi;
 	struct f2fs_dev_info *dev;
-	bool zone_cap_mismatch;
 };
 
 static int f2fs_report_zone_cb(struct blk_zone *zone, unsigned int idx,
 			      void *data)
 {
 	struct f2fs_report_zones_args *rz_args = data;
+	block_t unusable_blocks = (zone->len - zone->capacity) >>
+					F2FS_LOG_SECTORS_PER_BLOCK;
 
 	if (zone->type == BLK_ZONE_TYPE_CONVENTIONAL)
 		return 0;
 
 	set_bit(idx, rz_args->dev->blkz_seq);
-	rz_args->dev->zone_capacity_blocks[idx] = zone->capacity >>
-						F2FS_LOG_SECTORS_PER_BLOCK;
-	if (zone->len != zone->capacity && !rz_args->zone_cap_mismatch)
-		rz_args->zone_cap_mismatch = true;
-
+	if (!rz_args->sbi->unusable_blocks_per_sec) {
+		rz_args->sbi->unusable_blocks_per_sec = unusable_blocks;
+		return 0;
+	}
+	if (rz_args->sbi->unusable_blocks_per_sec != unusable_blocks) {
+		f2fs_err(rz_args->sbi, "F2FS supports single zone capacity\n");
+		return -EINVAL;
+	}
 	return 0;
 }
 
@@ -3622,26 +3728,13 @@
 	if (!FDEV(devi).blkz_seq)
 		return -ENOMEM;
 
-	/* Get block zones type and zone-capacity */
-	FDEV(devi).zone_capacity_blocks = f2fs_kzalloc(sbi,
-					FDEV(devi).nr_blkz * sizeof(block_t),
-					GFP_KERNEL);
-	if (!FDEV(devi).zone_capacity_blocks)
-		return -ENOMEM;
-
+	rep_zone_arg.sbi = sbi;
 	rep_zone_arg.dev = &FDEV(devi);
-	rep_zone_arg.zone_cap_mismatch = false;
 
 	ret = blkdev_report_zones(bdev, 0, BLK_ALL_ZONES, f2fs_report_zone_cb,
 				  &rep_zone_arg);
 	if (ret < 0)
 		return ret;
-
-	if (!rep_zone_arg.zone_cap_mismatch) {
-		kfree(FDEV(devi).zone_capacity_blocks);
-		FDEV(devi).zone_capacity_blocks = NULL;
-	}
-
 	return 0;
 }
 #endif
@@ -3747,6 +3840,7 @@
 {
 	struct f2fs_super_block *raw_super = F2FS_RAW_SUPER(sbi);
 	unsigned int max_devices = MAX_DEVICES;
+	unsigned int logical_blksize;
 	int i;
 
 	/* Initialize single device information */
@@ -3767,6 +3861,9 @@
 	if (!sbi->devs)
 		return -ENOMEM;
 
+	logical_blksize = bdev_logical_block_size(sbi->sb->s_bdev);
+	sbi->aligned_blksize = true;
+
 	for (i = 0; i < max_devices; i++) {
 
 		if (i > 0 && !RDEV(i).path[0])
@@ -3803,6 +3900,9 @@
 		/* to release errored devices */
 		sbi->s_ndevs = i + 1;
 
+		if (logical_blksize != bdev_logical_block_size(FDEV(i).bdev))
+			sbi->aligned_blksize = false;
+
 #ifdef CONFIG_BLK_DEV_ZONED
 		if (bdev_zoned_model(FDEV(i).bdev) == BLK_ZONED_HM &&
 				!f2fs_sb_has_blkzoned(sbi)) {
@@ -3884,7 +3984,8 @@
 		F2FS_OPTION(sbi).alloc_mode = ALLOC_MODE_REUSE;
 		if (f2fs_block_unit_discard(sbi))
 			sm_i->dcc_info->discard_granularity = 1;
-		sm_i->ipu_policy = 1 << F2FS_IPU_FORCE;
+		sm_i->ipu_policy = 1 << F2FS_IPU_FORCE |
+					1 << F2FS_IPU_HONOR_OPU_WRITE;
 	}
 
 	sbi->readdir_ra = 1;
@@ -4148,6 +4249,10 @@
 		goto free_nm;
 	}
 
+	err = adjust_reserved_segment(sbi);
+	if (err)
+		goto free_nm;
+
 	/* For write statistics */
 	sbi->sectors_written_start = f2fs_get_sectors_written(sbi);
 
@@ -4352,12 +4457,14 @@
 free_stats:
 	f2fs_destroy_stats(sbi);
 free_nm:
+	/* stop discard thread before destroying node manager */
+	f2fs_stop_discard_thread(sbi);
 	f2fs_destroy_node_manager(sbi);
 free_sm:
 	f2fs_destroy_segment_manager(sbi);
-	f2fs_destroy_post_read_wq(sbi);
 stop_ckpt_thread:
 	f2fs_stop_ckpt_thread(sbi);
+	f2fs_destroy_post_read_wq(sbi);
 free_devices:
 	destroy_device_list(sbi);
 	kvfree(sbi->ckpt);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/sysfs.c
@@ -407,15 +407,23 @@
 	if (ret < 0)
 		return ret;
 #ifdef CONFIG_F2FS_FAULT_INJECTION
-	if (a->struct_type == FAULT_INFO_TYPE && t >= (1 << FAULT_MAX))
-		return -EINVAL;
-	if (a->struct_type == FAULT_INFO_RATE && t >= UINT_MAX)
-		return -EINVAL;
+	if (a->struct_type == FAULT_INFO_TYPE) {
+		if (f2fs_build_fault_attr(sbi, 0, t))
+			return -EINVAL;
+		return count;
+	}
+	if (a->struct_type == FAULT_INFO_RATE) {
+		if (f2fs_build_fault_attr(sbi, t, 0))
+			return -EINVAL;
+		return count;
+	}
 #endif
 	if (a->struct_type == RESERVED_BLOCKS) {
 		spin_lock(&sbi->stat_lock);
 		if (t > (unsigned long)(sbi->user_block_count -
-				F2FS_OPTION(sbi).root_reserved_blocks)) {
+				F2FS_OPTION(sbi).root_reserved_blocks -
+				sbi->blocks_per_seg *
+				SM_I(sbi)->additional_reserved_segments)) {
 			spin_unlock(&sbi->stat_lock);
 			return -EINVAL;
 		}
@@ -471,7 +479,7 @@
 		} else if (t == GC_IDLE_AT) {
 			if (!sbi->am.atgc_enabled)
 				return -EINVAL;
-			sbi->gc_mode = GC_AT;
+			sbi->gc_mode = GC_IDLE_AT;
 		} else {
 			sbi->gc_mode = GC_NORMAL;
 		}
@@ -489,9 +497,9 @@
 	if (!strcmp(a->attr.name, "iostat_period_ms")) {
 		if (t < MIN_IOSTAT_PERIOD_MS || t > MAX_IOSTAT_PERIOD_MS)
 			return -EINVAL;
-		spin_lock(&sbi->iostat_lock);
+		spin_lock_irq(&sbi->iostat_lock);
 		sbi->iostat_period_ms = (unsigned int)t;
-		spin_unlock(&sbi->iostat_lock);
+		spin_unlock_irq(&sbi->iostat_lock);
 		return count;
 	}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/verity.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/verity.c
@@ -47,16 +47,13 @@
 		size_t n = min_t(size_t, count,
 				 PAGE_SIZE - offset_in_page(pos));
 		struct page *page;
-		void *addr;
 
 		page = read_mapping_page(inode->i_mapping, pos >> PAGE_SHIFT,
 					 NULL);
 		if (IS_ERR(page))
 			return PTR_ERR(page);
 
-		addr = kmap_atomic(page);
-		memcpy(buf, addr + offset_in_page(pos), n);
-		kunmap_atomic(addr);
+		memcpy_from_page(buf, page, offset_in_page(pos), n);
 
 		put_page(page);
 
@@ -81,8 +78,7 @@
 		size_t n = min_t(size_t, count,
 				 PAGE_SIZE - offset_in_page(pos));
 		struct page *page;
-		void *fsdata;
-		void *addr;
+		void *fsdata = NULL;
 		int res;
 
 		res = pagecache_write_begin(NULL, inode->i_mapping, pos, n, 0,
@@ -90,9 +86,7 @@
 		if (res)
 			return res;
 
-		addr = kmap_atomic(page);
-		memcpy(addr + offset_in_page(pos), buf, n);
-		kunmap_atomic(addr);
+		memcpy_to_page(page, offset_in_page(pos), buf, n);
 
 		res = pagecache_write_end(NULL, inode->i_mapping, pos, n, n,
 					  page, fsdata);
@@ -136,7 +130,7 @@
 	 * here and not rely on ->open() doing it.  This must be done before
 	 * evicting the inline data.
 	 */
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		return err;
 
@@ -261,13 +255,14 @@
 					       pgoff_t index,
 					       unsigned long num_ra_pages)
 {
-	DEFINE_READAHEAD(ractl, NULL, NULL, inode->i_mapping, index);
 	struct page *page;
 
 	index += f2fs_verity_metadata_pos(inode) >> PAGE_SHIFT;
 
 	page = find_get_page_flags(inode->i_mapping, index, FGP_ACCESSED);
 	if (!page || !PageUptodate(page)) {
+		DEFINE_READAHEAD(ractl, NULL, NULL, inode->i_mapping, index);
+
 		if (page)
 			put_page(page);
 		else if (num_ra_pages > 1)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/f2fs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/f2fs/xattr.c
@@ -631,6 +631,7 @@
 			const char *name, const void *value, size_t size,
 			struct page *ipage, int flags)
 {
+	struct f2fs_sb_info *sbi = F2FS_I_SB(inode);
 	struct f2fs_xattr_entry *here, *last;
 	void *base_addr, *last_base_addr;
 	int found, newsize;
@@ -684,8 +685,17 @@
 	}
 
 	last = here;
-	while (!IS_XATTR_LAST_ENTRY(last))
+	while (!IS_XATTR_LAST_ENTRY(last)) {
+		if ((void *)(last) + sizeof(__u32) > last_base_addr ||
+			(void *)XATTR_NEXT_ENTRY(last) > last_base_addr) {
+			f2fs_err(F2FS_I_SB(inode), "inode (%lu) has invalid last xattr entry, entry_size: %zu",
+					inode->i_ino, ENTRY_SIZE(last));
+			set_sbi_flag(F2FS_I_SB(inode), SBI_NEED_FSCK);
+			error = -EFSCORRUPTED;
+			goto exit;
+		}
 		last = XATTR_NEXT_ENTRY(last);
+	}
 
 	newsize = XATTR_ALIGN(sizeof(struct f2fs_xattr_entry) + len + size);
 
@@ -736,6 +746,12 @@
 		memcpy(pval, value, size);
 		last->e_value_size = cpu_to_le16(size);
 		new_hsize += newsize;
+		/*
+		 * Explicitly add the null terminator.  The unused xattr space
+		 * is supposed to always be zeroed, which would make this
+		 * unnecessary, but don't depend on that.
+		 */
+		*(u32 *)((u8 *)last + newsize) = 0;
 	}
 
 	error = write_all_xattrs(inode, new_hsize, base_addr, ipage);
@@ -745,17 +761,26 @@
 	if (index == F2FS_XATTR_INDEX_ENCRYPTION &&
 			!strcmp(name, F2FS_XATTR_NAME_ENCRYPTION_CONTEXT))
 		f2fs_set_encrypted_inode(inode);
-	f2fs_mark_inode_dirty_sync(inode, true);
-	if (!error && S_ISDIR(inode->i_mode))
-		set_sbi_flag(F2FS_I_SB(inode), SBI_NEED_CP);
 
+	if (!S_ISDIR(inode->i_mode))
+		goto same;
+	/*
+	 * In restrict mode, fsync() always try to trigger checkpoint for all
+	 * metadata consistency, in other mode, it triggers checkpoint when
+	 * parent's xattr metadata was updated.
+	 */
+	if (F2FS_OPTION(sbi).fsync_mode == FSYNC_MODE_STRICT)
+		set_sbi_flag(sbi, SBI_NEED_CP);
+	else
+		f2fs_add_ino_entry(sbi, inode->i_ino, XATTR_DIR_INO);
 same:
 	if (is_inode_flag_set(inode, FI_ACL_MODE)) {
 		inode->i_mode = F2FS_I(inode)->i_acl_mode;
-		inode->i_ctime = current_time(inode);
 		clear_inode_flag(inode, FI_ACL_MODE);
 	}
 
+	inode->i_ctime = current_time(inode);
+	f2fs_mark_inode_dirty_sync(inode, true);
 exit:
 	kfree(base_addr);
 	return error;
@@ -773,7 +798,7 @@
 	if (!f2fs_is_checkpoint_ready(sbi))
 		return -ENOSPC;
 
-	err = dquot_initialize(inode);
+	err = f2fs_dquot_initialize(inode);
 	if (err)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fat/fatent.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fat/fatent.c
@@ -94,7 +94,8 @@
 err_brelse:
 	brelse(bhs[0]);
 err:
-	fat_msg(sb, KERN_ERR, "FAT read failed (blocknr %llu)", (llu)blocknr);
+	fat_msg_ratelimit(sb, KERN_ERR, "FAT read failed (blocknr %llu)",
+			  (llu)blocknr);
 	return -EIO;
 }
 
@@ -107,8 +108,8 @@
 	fatent->fat_inode = MSDOS_SB(sb)->fat_inode;
 	fatent->bhs[0] = sb_bread(sb, blocknr);
 	if (!fatent->bhs[0]) {
-		fat_msg(sb, KERN_ERR, "FAT read failed (blocknr %llu)",
-		       (llu)blocknr);
+		fat_msg_ratelimit(sb, KERN_ERR, "FAT read failed (blocknr %llu)",
+				  (llu)blocknr);
 		return -EIO;
 	}
 	fatent->nr_bhs = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fat/namei_vfat.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fat/namei_vfat.c
@@ -1020,7 +1020,7 @@
 	if (corrupt < 0) {
 		fat_fs_error(new_dir->i_sb,
 			     "%s: Filesystem corrupted (i_pos %lld)",
-			     __func__, sinfo.i_pos);
+			     __func__, new_i_pos);
 	}
 	goto out;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fat/nfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fat/nfs.c
@@ -130,6 +130,12 @@
 		fid->parent_i_gen = parent->i_generation;
 		type = FILEID_FAT_WITH_PARENT;
 		*lenp = FAT_FID_SIZE_WITH_PARENT;
+	} else {
+		/*
+		 * We need to initialize this field because the fh is actually
+		 * 12 bytes long
+		 */
+		fid->parent_i_pos_hi = 0;
 	}
 
 	return type;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fcntl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fcntl.c
@@ -33,7 +33,7 @@
 
 #define SETFL_MASK (O_APPEND | O_NONBLOCK | O_NDELAY | O_DIRECT | O_NOATIME)
 
-static int setfl(int fd, struct file * filp, unsigned long arg)
+int setfl(int fd, struct file *filp, unsigned long arg)
 {
 	struct inode * inode = file_inode(filp);
 	int error = 0;
@@ -64,6 +64,8 @@
 
 	if (filp->f_op->check_flags)
 		error = filp->f_op->check_flags(arg);
+	if (!error && filp->f_op->setfl)
+		error = filp->f_op->setfl(filp, arg);
 	if (error)
 		return error;
 
@@ -84,9 +86,10 @@
  out:
 	return error;
 }
+EXPORT_SYMBOL_GPL(setfl);
 
-static void f_modown(struct file *filp, struct pid *pid, enum pid_type type,
-                     int force)
+void __f_setown(struct file *filp, struct pid *pid, enum pid_type type,
+		int force)
 {
 	write_lock_irq(&filp->f_owner.lock);
 	if (force || !filp->f_owner.pid) {
@@ -96,19 +99,13 @@
 
 		if (pid) {
 			const struct cred *cred = current_cred();
+			security_file_set_fowner(filp);
 			filp->f_owner.uid = cred->uid;
 			filp->f_owner.euid = cred->euid;
 		}
 	}
 	write_unlock_irq(&filp->f_owner.lock);
 }
-
-void __f_setown(struct file *filp, struct pid *pid, enum pid_type type,
-		int force)
-{
-	security_file_set_fowner(filp);
-	f_modown(filp, pid, type, force);
-}
 EXPORT_SYMBOL(__f_setown);
 
 int f_setown(struct file *filp, unsigned long arg, int force)
@@ -144,7 +141,7 @@
 
 void f_delown(struct file *filp)
 {
-	f_modown(filp, NULL, PIDTYPE_TGID, 1);
+	__f_setown(filp, NULL, PIDTYPE_TGID, 1);
 }
 
 pid_t f_getown(struct file *filp)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fhandle.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fhandle.c
@@ -37,7 +37,7 @@
 	if (f_handle.handle_bytes > MAX_HANDLE_SZ)
 		return -EINVAL;
 
-	handle = kmalloc(sizeof(struct file_handle) + f_handle.handle_bytes,
+	handle = kzalloc(sizeof(struct file_handle) + f_handle.handle_bytes,
 			 GFP_KERNEL);
 	if (!handle)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/file.c
@@ -21,6 +21,7 @@
 #include <linux/rcupdate.h>
 #include <linux/close_range.h>
 #include <net/sock.h>
+#include <linux/init_task.h>
 
 #include "internal.h"
 
@@ -46,27 +47,23 @@
 #define BITBIT_NR(nr)	BITS_TO_LONGS(BITS_TO_LONGS(nr))
 #define BITBIT_SIZE(nr)	(BITBIT_NR(nr) * sizeof(long))
 
+#define fdt_words(fdt) ((fdt)->max_fds / BITS_PER_LONG) // words in ->open_fds
 /*
  * Copy 'count' fd bits from the old table to the new table and clear the extra
  * space if any.  This does not copy the file pointers.  Called with the files
  * spinlock held for write.
  */
-static void copy_fd_bitmaps(struct fdtable *nfdt, struct fdtable *ofdt,
-			    unsigned int count)
+static inline void copy_fd_bitmaps(struct fdtable *nfdt, struct fdtable *ofdt,
+			    unsigned int copy_words)
 {
-	unsigned int cpy, set;
+	unsigned int nwords = fdt_words(nfdt);
 
-	cpy = count / BITS_PER_BYTE;
-	set = (nfdt->max_fds - count) / BITS_PER_BYTE;
-	memcpy(nfdt->open_fds, ofdt->open_fds, cpy);
-	memset((char *)nfdt->open_fds + cpy, 0, set);
-	memcpy(nfdt->close_on_exec, ofdt->close_on_exec, cpy);
-	memset((char *)nfdt->close_on_exec + cpy, 0, set);
-
-	cpy = BITBIT_SIZE(count);
-	set = BITBIT_SIZE(nfdt->max_fds) - cpy;
-	memcpy(nfdt->full_fds_bits, ofdt->full_fds_bits, cpy);
-	memset((char *)nfdt->full_fds_bits + cpy, 0, set);
+	bitmap_copy_and_extend(nfdt->open_fds, ofdt->open_fds,
+			copy_words * BITS_PER_LONG, nwords * BITS_PER_LONG);
+	bitmap_copy_and_extend(nfdt->close_on_exec, ofdt->close_on_exec,
+			copy_words * BITS_PER_LONG, nwords * BITS_PER_LONG);
+	bitmap_copy_and_extend(nfdt->full_fds_bits, ofdt->full_fds_bits,
+			copy_words, nwords);
 }
 
 /*
@@ -84,9 +81,24 @@
 	memcpy(nfdt->fd, ofdt->fd, cpy);
 	memset((char *)nfdt->fd + cpy, 0, set);
 
-	copy_fd_bitmaps(nfdt, ofdt, ofdt->max_fds);
+	copy_fd_bitmaps(nfdt, ofdt, fdt_words(ofdt));
 }
 
+/*
+ * Note how the fdtable bitmap allocations very much have to be a multiple of
+ * BITS_PER_LONG. This is not only because we walk those things in chunks of
+ * 'unsigned long' in some places, but simply because that is how the Linux
+ * kernel bitmaps are defined to work: they are not "bits in an array of bytes",
+ * they are very much "bits in an array of unsigned long".
+ *
+ * The ALIGN(nr, BITS_PER_LONG) here is for clarity: since we just multiplied
+ * by that "1024/sizeof(ptr)" before, we already know there are sufficient
+ * clear low bits. Clang seems to realize that, gcc ends up being confused.
+ *
+ * On a 128-bit machine, the ALIGN() would actually matter. In the meantime,
+ * let's consider it documentation (and maybe a test-case for gcc to improve
+ * its code generation ;)
+ */
 static struct fdtable * alloc_fdtable(unsigned int nr)
 {
 	struct fdtable *fdt;
@@ -102,6 +114,7 @@
 	nr /= (1024 / sizeof(struct file *));
 	nr = roundup_pow_of_two(nr + 1);
 	nr *= (1024 / sizeof(struct file *));
+	nr = ALIGN(nr, BITS_PER_LONG);
 	/*
 	 * Note that this can drive nr *below* what we had passed if sysctl_nr_open
 	 * had been set lower between the check in expand_files() and here.  Deal
@@ -255,46 +268,45 @@
 	__clear_bit(fd / BITS_PER_LONG, fdt->full_fds_bits);
 }
 
-static unsigned int count_open_files(struct fdtable *fdt)
+/*
+ * Note that a sane fdtable size always has to be a multiple of
+ * BITS_PER_LONG, since we have bitmaps that are sized by this.
+ *
+ * punch_hole is optional - when close_range() is asked to unshare
+ * and close, we don't need to copy descriptors in that range, so
+ * a smaller cloned descriptor table might suffice if the last
+ * currently opened descriptor falls into that range.
+ */
+static unsigned int sane_fdtable_size(struct fdtable *fdt, struct fd_range *punch_hole)
 {
-	unsigned int size = fdt->max_fds;
-	unsigned int i;
+	unsigned int last = find_last_bit(fdt->open_fds, fdt->max_fds);
 
-	/* Find the last open fd */
-	for (i = size / BITS_PER_LONG; i > 0; ) {
-		if (fdt->open_fds[--i])
-			break;
+	if (last == fdt->max_fds)
+		return NR_OPEN_DEFAULT;
+	if (punch_hole && punch_hole->to >= last && punch_hole->from <= last) {
+		last = find_last_bit(fdt->open_fds, punch_hole->from);
+		if (last == punch_hole->from)
+			return NR_OPEN_DEFAULT;
 	}
-	i = (i + 1) * BITS_PER_LONG;
-	return i;
-}
-
-static unsigned int sane_fdtable_size(struct fdtable *fdt, unsigned int max_fds)
-{
-	unsigned int count;
-
-	count = count_open_files(fdt);
-	if (max_fds < NR_OPEN_DEFAULT)
-		max_fds = NR_OPEN_DEFAULT;
-	return min(count, max_fds);
+	return ALIGN(last + 1, BITS_PER_LONG);
 }
 
 /*
- * Allocate a new files structure and copy contents from the
- * passed in files structure.
- * errorp will be valid only when the returned files_struct is NULL.
+ * Allocate a new descriptor table and copy contents from the passed in
+ * instance.  Returns a pointer to cloned table on success, ERR_PTR()
+ * on failure.  For 'punch_hole' see sane_fdtable_size().
  */
-struct files_struct *dup_fd(struct files_struct *oldf, unsigned int max_fds, int *errorp)
+struct files_struct *dup_fd(struct files_struct *oldf, struct fd_range *punch_hole)
 {
 	struct files_struct *newf;
 	struct file **old_fds, **new_fds;
 	unsigned int open_files, i;
 	struct fdtable *old_fdt, *new_fdt;
+	int error;
 
-	*errorp = -ENOMEM;
 	newf = kmem_cache_alloc(files_cachep, GFP_KERNEL);
 	if (!newf)
-		goto out;
+		return ERR_PTR(-ENOMEM);
 
 	atomic_set(&newf->count, 1);
 
@@ -311,7 +323,7 @@
 
 	spin_lock(&oldf->file_lock);
 	old_fdt = files_fdtable(oldf);
-	open_files = sane_fdtable_size(old_fdt, max_fds);
+	open_files = sane_fdtable_size(old_fdt, punch_hole);
 
 	/*
 	 * Check whether we need to allocate a larger fd array and fd set.
@@ -324,14 +336,14 @@
 
 		new_fdt = alloc_fdtable(open_files - 1);
 		if (!new_fdt) {
-			*errorp = -ENOMEM;
+			error = -ENOMEM;
 			goto out_release;
 		}
 
 		/* beyond sysctl_nr_open; nothing to do */
 		if (unlikely(new_fdt->max_fds < open_files)) {
 			__free_fdtable(new_fdt);
-			*errorp = -EMFILE;
+			error = -EMFILE;
 			goto out_release;
 		}
 
@@ -342,10 +354,10 @@
 		 */
 		spin_lock(&oldf->file_lock);
 		old_fdt = files_fdtable(oldf);
-		open_files = sane_fdtable_size(old_fdt, max_fds);
+		open_files = sane_fdtable_size(old_fdt, punch_hole);
 	}
 
-	copy_fd_bitmaps(new_fdt, old_fdt, open_files);
+	copy_fd_bitmaps(new_fdt, old_fdt, open_files / BITS_PER_LONG);
 
 	old_fds = old_fdt->fd;
 	new_fds = new_fdt->fd;
@@ -376,8 +388,7 @@
 
 out_release:
 	kmem_cache_free(files_cachep, newf);
-out:
-	return NULL;
+	return ERR_PTR(error);
 }
 
 static struct fdtable *close_files(struct files_struct * files)
@@ -452,12 +463,12 @@
 
 static unsigned int find_next_fd(struct fdtable *fdt, unsigned int start)
 {
-	unsigned int maxfd = fdt->max_fds;
+	unsigned int maxfd = fdt->max_fds; /* always multiple of BITS_PER_LONG */
 	unsigned int maxbit = maxfd / BITS_PER_LONG;
 	unsigned int bitbit = start / BITS_PER_LONG;
 
 	bitbit = find_next_zero_bit(fdt->full_fds_bits, maxbit, bitbit) * BITS_PER_LONG;
-	if (bitbit > maxfd)
+	if (bitbit >= maxfd)
 		return maxfd;
 	if (bitbit > start)
 		start = bitbit;
@@ -617,6 +628,7 @@
 		file = ERR_PTR(-EINVAL);
 		goto out_unlock;
 	}
+	fd = array_index_nospec(fd, fdt->max_fds);
 	file = fdt->fd[fd];
 	if (!file) {
 		file = ERR_PTR(-EBADF);
@@ -710,37 +722,25 @@
 	if (fd > max_fd)
 		return -EINVAL;
 
-	if (flags & CLOSE_RANGE_UNSHARE) {
-		int ret;
-		unsigned int max_unshare_fds = NR_OPEN_MAX;
+	if ((flags & CLOSE_RANGE_UNSHARE) && atomic_read(&cur_fds->count) > 1) {
+		struct fd_range range = {fd, max_fd}, *punch_hole = &range;
 
 		/*
 		 * If the caller requested all fds to be made cloexec we always
 		 * copy all of the file descriptors since they still want to
 		 * use them.
 		 */
-		if (!(flags & CLOSE_RANGE_CLOEXEC)) {
-			/*
-			 * If the requested range is greater than the current
-			 * maximum, we're closing everything so only copy all
-			 * file descriptors beneath the lowest file descriptor.
-			 */
-			rcu_read_lock();
-			if (max_fd >= last_fd(files_fdtable(cur_fds)))
-				max_unshare_fds = fd;
-			rcu_read_unlock();
-		}
-
-		ret = unshare_fd(CLONE_FILES, max_unshare_fds, &fds);
-		if (ret)
-			return ret;
+		if (flags & CLOSE_RANGE_CLOEXEC)
+			punch_hole = NULL;
 
+		fds = dup_fd(cur_fds, punch_hole);
+		if (IS_ERR(fds))
+			return PTR_ERR(fds);
 		/*
 		 * We used to share our file descriptor table, and have now
 		 * created a private one, make sure we're using it below.
 		 */
-		if (fds)
-			swap(cur_fds, fds);
+		swap(cur_fds, fds);
 	}
 
 	if (flags & CLOSE_RANGE_CLOEXEC)
@@ -787,6 +787,7 @@
 	*res = NULL;
 	return -ENOENT;
 }
+EXPORT_SYMBOL(close_fd_get_file);
 
 /*
  * variant of close_fd that gets a ref on the file for later fput.
@@ -841,24 +842,68 @@
 	spin_unlock(&files->file_lock);
 }
 
+static inline struct file *__fget_files_rcu(struct files_struct *files,
+	unsigned int fd, fmode_t mask, unsigned int refs)
+{
+	for (;;) {
+		struct file *file;
+		struct fdtable *fdt = rcu_dereference_raw(files->fdt);
+		struct file __rcu **fdentry;
+
+		if (unlikely(fd >= fdt->max_fds))
+			return NULL;
+
+		fdentry = fdt->fd + array_index_nospec(fd, fdt->max_fds);
+		file = rcu_dereference_raw(*fdentry);
+		if (unlikely(!file))
+			return NULL;
+
+		if (unlikely(file->f_mode & mask))
+			return NULL;
+
+		/*
+		 * Ok, we have a file pointer. However, because we do
+		 * this all locklessly under RCU, we may be racing with
+		 * that file being closed.
+		 *
+		 * Such a race can take two forms:
+		 *
+		 *  (a) the file ref already went down to zero,
+		 *      and get_file_rcu_many() fails. Just try
+		 *      again:
+		 */
+		if (unlikely(!get_file_rcu_many(file, refs)))
+			continue;
+
+		/*
+		 *  (b) the file table entry has changed under us.
+		 *       Note that we don't need to re-check the 'fdt->fd'
+		 *       pointer having changed, because it always goes
+		 *       hand-in-hand with 'fdt'.
+		 *
+		 * If so, we need to put our refs and try again.
+		 */
+		if (unlikely(rcu_dereference_raw(files->fdt) != fdt) ||
+		    unlikely(rcu_dereference_raw(*fdentry) != file)) {
+			fput_many(file, refs);
+			continue;
+		}
+
+		/*
+		 * Ok, we have a ref to the file, and checked that it
+		 * still exists.
+		 */
+		return file;
+	}
+}
+
 static struct file *__fget_files(struct files_struct *files, unsigned int fd,
 				 fmode_t mask, unsigned int refs)
 {
 	struct file *file;
 
 	rcu_read_lock();
-loop:
-	file = files_lookup_fd_rcu(files, fd);
-	if (file) {
-		/* File object ref couldn't be taken.
-		 * dup2() atomicity guarantee is the reason
-		 * we loop to catch the new file (or NULL pointer)
-		 */
-		if (file->f_mode & mask)
-			file = NULL;
-		else if (!get_file_rcu_many(file, refs))
-			goto loop;
-	}
+	file = __fget_files_rcu(files, fd, mask, refs);
 	rcu_read_unlock();
 
 	return file;
@@ -956,7 +1001,16 @@
 	struct files_struct *files = current->files;
 	struct file *file;
 
-	if (atomic_read(&files->count) == 1) {
+	/*
+	 * If another thread is concurrently calling close_fd() followed
+	 * by put_files_struct(), we must not observe the old table
+	 * entry combined with the new refcount - otherwise we could
+	 * return a file that is concurrently being freed.
+	 *
+	 * atomic_read_acquire() pairs with atomic_dec_and_test() in
+	 * put_files_struct().
+	 */
+	if (atomic_read_acquire(&files->count) == 1) {
 		file = files_lookup_fd_raw(files, fd);
 		if (!file || unlikely(file->f_mode & mask))
 			return 0;
@@ -979,16 +1033,30 @@
 	return __fget_light(fd, 0);
 }
 
+/*
+ * Try to avoid f_pos locking. We only need it if the
+ * file is marked for FMODE_ATOMIC_POS, and it can be
+ * accessed multiple ways.
+ *
+ * Always do it for directories, because pidfd_getfd()
+ * can make a file accessible even if it otherwise would
+ * not be, and for directories this is a correctness
+ * issue, not a "POSIX requirement".
+ */
+static inline bool file_needs_f_pos_lock(struct file *file)
+{
+	return (file->f_mode & FMODE_ATOMIC_POS) &&
+		(file_count(file) > 1 || S_ISDIR(file_inode(file)->i_mode));
+}
+
 unsigned long __fdget_pos(unsigned int fd)
 {
 	unsigned long v = __fdget(fd);
 	struct file *file = (struct file *)(v & ~3);
 
-	if (file && (file->f_mode & FMODE_ATOMIC_POS)) {
-		if (file_count(file) > 1) {
-			v |= FDPUT_POS_UNLOCK;
-			mutex_lock(&file->f_pos_lock);
-		}
+	if (file && file_needs_f_pos_lock(file)) {
+		v |= FDPUT_POS_UNLOCK;
+		mutex_lock(&file->f_pos_lock);
 	}
 	return v;
 }
@@ -1051,6 +1119,7 @@
 	 * tables and this condition does not arise without those.
 	 */
 	fdt = files_fdtable(files);
+	fd = array_index_nospec(fd, fdt->max_fds);
 	tofree = fdt->fd[fd];
 	if (!tofree && fd_is_open(fd, fdt))
 		goto Ebusy;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/file_table.c
+++ linux-xilinx-zynqmp-5.15.0/fs/file_table.c
@@ -33,7 +33,7 @@
 #include "internal.h"
 
 /* sysctl tunables... */
-struct files_stat_struct files_stat = {
+static struct files_stat_struct files_stat = {
 	.max_files = NR_FILE
 };
 
@@ -75,22 +75,53 @@
 }
 EXPORT_SYMBOL_GPL(get_max_files);
 
+#if defined(CONFIG_SYSCTL) && defined(CONFIG_PROC_FS)
+
 /*
  * Handle nr_files sysctl
  */
-#if defined(CONFIG_SYSCTL) && defined(CONFIG_PROC_FS)
-int proc_nr_files(struct ctl_table *table, int write,
-                     void *buffer, size_t *lenp, loff_t *ppos)
+static int proc_nr_files(struct ctl_table *table, int write, void *buffer,
+			 size_t *lenp, loff_t *ppos)
 {
 	files_stat.nr_files = get_nr_files();
 	return proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
 }
-#else
-int proc_nr_files(struct ctl_table *table, int write,
-                     void *buffer, size_t *lenp, loff_t *ppos)
+
+static struct ctl_table fs_stat_sysctls[] = {
+	{
+		.procname	= "file-nr",
+		.data		= &files_stat,
+		.maxlen		= sizeof(files_stat),
+		.mode		= 0444,
+		.proc_handler	= proc_nr_files,
+	},
+	{
+		.procname	= "file-max",
+		.data		= &files_stat.max_files,
+		.maxlen		= sizeof(files_stat.max_files),
+		.mode		= 0644,
+		.proc_handler	= proc_doulongvec_minmax,
+		.extra1		= SYSCTL_LONG_ZERO,
+		.extra2		= SYSCTL_LONG_MAX,
+	},
+	{
+		.procname	= "nr_open",
+		.data		= &sysctl_nr_open,
+		.maxlen		= sizeof(unsigned int),
+		.mode		= 0644,
+		.proc_handler	= proc_douintvec_minmax,
+		.extra1		= &sysctl_nr_open_min,
+		.extra2		= &sysctl_nr_open_max,
+	},
+	{ }
+};
+
+static int __init init_fs_stat_sysctls(void)
 {
-	return -ENOSYS;
+	register_sysctl_init("fs", fs_stat_sysctls);
+	return 0;
 }
+fs_initcall(init_fs_stat_sysctls);
 #endif
 
 static struct file *__alloc_file(int flags, const struct cred *cred)
@@ -161,6 +192,7 @@
 	}
 	return ERR_PTR(-ENFILE);
 }
+EXPORT_SYMBOL_GPL(alloc_empty_file);
 
 /*
  * Variant of alloc_empty_file() that doesn't check and modify nr_files.
@@ -284,12 +316,7 @@
 	}
 	fops_put(file->f_op);
 	put_pid(file->f_owner.pid);
-	if ((mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ)
-		i_readcount_dec(inode);
-	if (mode & FMODE_WRITER) {
-		put_write_access(inode);
-		__mnt_drop_write(mnt);
-	}
+	put_file_access(file);
 	dput(dentry);
 	if (unlikely(mode & FMODE_NEED_UNMOUNT))
 		dissolve_on_fput(mnt);
@@ -375,6 +402,7 @@
 }
 
 EXPORT_SYMBOL(fput);
+EXPORT_SYMBOL_GPL(__fput_sync);
 
 void __init files_init(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fs-writeback.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fs-writeback.c
@@ -120,6 +120,7 @@
 				      struct list_head *head)
 {
 	assert_spin_locked(&wb->list_lock);
+	assert_spin_locked(&inode->i_lock);
 
 	list_move(&inode->i_io_list, head);
 
@@ -133,10 +134,10 @@
 
 static void wb_wakeup(struct bdi_writeback *wb)
 {
-	spin_lock_bh(&wb->work_lock);
+	spin_lock_irq(&wb->work_lock);
 	if (test_bit(WB_registered, &wb->state))
 		mod_delayed_work(bdi_wq, &wb->dwork, 0);
-	spin_unlock_bh(&wb->work_lock);
+	spin_unlock_irq(&wb->work_lock);
 }
 
 static void finish_writeback_work(struct bdi_writeback *wb,
@@ -163,7 +164,7 @@
 	if (work->done)
 		atomic_inc(&work->done->cnt);
 
-	spin_lock_bh(&wb->work_lock);
+	spin_lock_irq(&wb->work_lock);
 
 	if (test_bit(WB_registered, &wb->state)) {
 		list_add_tail(&work->list, &wb->work_list);
@@ -171,7 +172,7 @@
 	} else
 		finish_writeback_work(wb, work);
 
-	spin_unlock_bh(&wb->work_lock);
+	spin_unlock_irq(&wb->work_lock);
 }
 
 /**
@@ -608,6 +609,24 @@
 	kfree(isw);
 }
 
+static bool isw_prepare_wbs_switch(struct inode_switch_wbs_context *isw,
+				   struct list_head *list, int *nr)
+{
+	struct inode *inode;
+
+	list_for_each_entry(inode, list, i_io_list) {
+		if (!inode_prepare_wbs_switch(inode, isw->new_wb))
+			continue;
+
+		isw->inodes[*nr] = inode;
+		(*nr)++;
+
+		if (*nr >= WB_MAX_INODES_PER_ISW - 1)
+			return true;
+	}
+	return false;
+}
+
 /**
  * cleanup_offline_cgwb - detach associated inodes
  * @wb: target wb
@@ -620,7 +639,6 @@
 {
 	struct cgroup_subsys_state *memcg_css;
 	struct inode_switch_wbs_context *isw;
-	struct inode *inode;
 	int nr;
 	bool restart = false;
 
@@ -642,17 +660,17 @@
 
 	nr = 0;
 	spin_lock(&wb->list_lock);
-	list_for_each_entry(inode, &wb->b_attached, i_io_list) {
-		if (!inode_prepare_wbs_switch(inode, isw->new_wb))
-			continue;
-
-		isw->inodes[nr++] = inode;
-
-		if (nr >= WB_MAX_INODES_PER_ISW - 1) {
-			restart = true;
-			break;
-		}
-	}
+	/*
+	 * In addition to the inodes that have completed writeback, also switch
+	 * cgwbs for those inodes only with dirty timestamps. Otherwise, those
+	 * inodes won't be written back for a long time when lazytime is
+	 * enabled, and thus pinning the dying cgwbs. It won't break the
+	 * bandwidth restrictions, as writeback of inode metadata is not
+	 * accounted for.
+	 */
+	restart = isw_prepare_wbs_switch(isw, &wb->b_attached, &nr);
+	if (!restart)
+		restart = isw_prepare_wbs_switch(isw, &wb->b_dirty_time, &nr);
 	spin_unlock(&wb->list_lock);
 
 	/* no attached inodes? bail out */
@@ -824,7 +842,7 @@
 		 * is okay.  The main goal is avoiding keeping an inode on
 		 * the wrong wb for an extended period of time.
 		 */
-		if (hweight32(history) > WB_FRN_HIST_THR_SLOTS)
+		if (hweight16(history) > WB_FRN_HIST_THR_SLOTS)
 			inode_switch_wbs(inode, max_id);
 	}
 
@@ -1008,6 +1026,16 @@
 			continue;
 		}
 
+		/*
+		 * If wb_tryget fails, the wb has been shutdown, skip it.
+		 *
+		 * Pin @wb so that it stays on @bdi->wb_list.  This allows
+		 * continuing iteration from @wb after dropping and
+		 * regrabbing rcu read lock.
+		 */
+		if (!wb_tryget(wb))
+			continue;
+
 		/* alloc failed, execute synchronously using on-stack fallback */
 		work = &fallback_work;
 		*work = *base_work;
@@ -1016,13 +1044,6 @@
 		work->done = &fallback_work_done;
 
 		wb_queue_work(wb, work);
-
-		/*
-		 * Pin @wb so that it stays on @bdi->wb_list.  This allows
-		 * continuing iteration from @wb after dropping and
-		 * regrabbing rcu read lock.
-		 */
-		wb_get(wb);
 		last_wb = wb;
 
 		rcu_read_unlock();
@@ -1400,9 +1421,9 @@
 		inode = wb_inode(delaying_queue->prev);
 		if (inode_dirtied_after(inode, dirtied_before))
 			break;
+		spin_lock(&inode->i_lock);
 		list_move(&inode->i_io_list, &tmp);
 		moved++;
-		spin_lock(&inode->i_lock);
 		inode->i_state |= I_SYNC_QUEUED;
 		spin_unlock(&inode->i_lock);
 		if (sb_is_blkdev_sb(inode->i_sb))
@@ -1418,7 +1439,12 @@
 		goto out;
 	}
 
-	/* Move inodes from one superblock together */
+	/*
+	 * Although inode's i_io_list is moved from 'tmp' to 'dispatch_queue',
+	 * we don't take inode->i_lock here because it is just a pointless overhead.
+	 * Inode is already marked as I_SYNC_QUEUED so writeback list handling is
+	 * fully under our control.
+	 */
 	while (!list_empty(&tmp)) {
 		sb = wb_inode(tmp.prev)->i_sb;
 		list_for_each_prev_safe(pos, node, &tmp) {
@@ -1548,10 +1574,15 @@
 
 	if (wbc->pages_skipped) {
 		/*
-		 * writeback is not making progress due to locked
-		 * buffers. Skip this inode for now.
+		 * Writeback is not making progress due to locked buffers.
+		 * Skip this inode for now. Although having skipped pages
+		 * is odd for clean inodes, it can happen for some
+		 * filesystems so handle that gracefully.
 		 */
-		redirty_tail_locked(inode, wb);
+		if (inode->i_state & I_DIRTY_ALL)
+			redirty_tail_locked(inode, wb);
+		else
+			inode_cgwb_move_to_attached(inode, wb);
 		return;
 	}
 
@@ -1733,12 +1764,29 @@
 	wb = inode_to_wb_and_lock_list(inode);
 	spin_lock(&inode->i_lock);
 	/*
-	 * If the inode is now fully clean, then it can be safely removed from
-	 * its writeback list (if any).  Otherwise the flusher threads are
-	 * responsible for the writeback lists.
+	 * If the inode is freeing, its i_io_list shoudn't be updated
+	 * as it can be finally deleted at this moment.
 	 */
-	if (!(inode->i_state & I_DIRTY_ALL))
-		inode_cgwb_move_to_attached(inode, wb);
+	if (!(inode->i_state & I_FREEING)) {
+		/*
+		 * If the inode is now fully clean, then it can be safely
+		 * removed from its writeback list (if any). Otherwise the
+		 * flusher threads are responsible for the writeback lists.
+		 */
+		if (!(inode->i_state & I_DIRTY_ALL))
+			inode_cgwb_move_to_attached(inode, wb);
+		else if (!(inode->i_state & I_SYNC_QUEUED)) {
+			if ((inode->i_state & I_DIRTY))
+				redirty_tail_locked(inode, wb);
+			else if (inode->i_state & I_DIRTY_TIME) {
+				inode->dirtied_when = jiffies;
+				inode_io_list_move_locked(inode,
+							  wb,
+							  &wb->b_dirty_time);
+			}
+		}
+	}
+
 	spin_unlock(&wb->list_lock);
 	inode_sync_complete(inode);
 out:
@@ -1802,11 +1850,12 @@
 	};
 	unsigned long start_time = jiffies;
 	long write_chunk;
-	long wrote = 0;  /* count both pages and inodes */
+	long total_wrote = 0;  /* count both pages and inodes */
 
 	while (!list_empty(&wb->b_io)) {
 		struct inode *inode = wb_inode(wb->b_io.prev);
 		struct bdi_writeback *tmp_wb;
+		long wrote;
 
 		if (inode->i_sb != sb) {
 			if (work->sb) {
@@ -1848,8 +1897,8 @@
 			 * We'll have another go at writing back this inode
 			 * when we completed a full scan of b_io.
 			 */
-			spin_unlock(&inode->i_lock);
 			requeue_io(inode, wb);
+			spin_unlock(&inode->i_lock);
 			trace_writeback_sb_inodes_requeue(inode);
 			continue;
 		}
@@ -1882,7 +1931,9 @@
 
 		wbc_detach_inode(&wbc);
 		work->nr_pages -= write_chunk - wbc.nr_to_write;
-		wrote += write_chunk - wbc.nr_to_write;
+		wrote = write_chunk - wbc.nr_to_write - wbc.pages_skipped;
+		wrote = wrote < 0 ? 0 : wrote;
+		total_wrote += wrote;
 
 		if (need_resched()) {
 			/*
@@ -1904,7 +1955,7 @@
 		tmp_wb = inode_to_wb_and_lock_list(inode);
 		spin_lock(&inode->i_lock);
 		if (!(inode->i_state & I_DIRTY_ALL))
-			wrote++;
+			total_wrote++;
 		requeue_inode(inode, tmp_wb, &wbc);
 		inode_sync_complete(inode);
 		spin_unlock(&inode->i_lock);
@@ -1918,14 +1969,14 @@
 		 * bail out to wb_writeback() often enough to check
 		 * background threshold and other termination conditions.
 		 */
-		if (wrote) {
+		if (total_wrote) {
 			if (time_is_before_jiffies(start_time + HZ / 10UL))
 				break;
 			if (work->nr_pages <= 0)
 				break;
 		}
 	}
-	return wrote;
+	return total_wrote;
 }
 
 static long __writeback_inodes_wb(struct bdi_writeback *wb,
@@ -2096,13 +2147,13 @@
 {
 	struct wb_writeback_work *work = NULL;
 
-	spin_lock_bh(&wb->work_lock);
+	spin_lock_irq(&wb->work_lock);
 	if (!list_empty(&wb->work_list)) {
 		work = list_entry(wb->work_list.next,
 				  struct wb_writeback_work, list);
 		list_del_init(&work->list);
 	}
-	spin_unlock_bh(&wb->work_lock);
+	spin_unlock_irq(&wb->work_lock);
 	return work;
 }
 
@@ -2382,11 +2433,26 @@
 {
 	struct super_block *sb = inode->i_sb;
 	int dirtytime = 0;
+	struct bdi_writeback *wb = NULL;
 
 	trace_writeback_mark_inode_dirty(inode, flags);
 
 	if (flags & I_DIRTY_INODE) {
 		/*
+		 * Inode timestamp update will piggback on this dirtying.
+		 * We tell ->dirty_inode callback that timestamps need to
+		 * be updated by setting I_DIRTY_TIME in flags.
+		 */
+		if (inode->i_state & I_DIRTY_TIME) {
+			spin_lock(&inode->i_lock);
+			if (inode->i_state & I_DIRTY_TIME) {
+				inode->i_state &= ~I_DIRTY_TIME;
+				flags |= I_DIRTY_TIME;
+			}
+			spin_unlock(&inode->i_lock);
+		}
+
+		/*
 		 * Notify the filesystem about the inode being dirtied, so that
 		 * (if needed) it can update on-disk fields and journal the
 		 * inode.  This is only needed when the inode itself is being
@@ -2395,7 +2461,8 @@
 		 */
 		trace_writeback_dirty_inode_start(inode, flags);
 		if (sb->s_op->dirty_inode)
-			sb->s_op->dirty_inode(inode, flags & I_DIRTY_INODE);
+			sb->s_op->dirty_inode(inode,
+				flags & (I_DIRTY_INODE | I_DIRTY_TIME));
 		trace_writeback_dirty_inode(inode, flags);
 
 		/* I_DIRTY_INODE supersedes I_DIRTY_TIME. */
@@ -2416,31 +2483,36 @@
 	 */
 	smp_mb();
 
-	if (((inode->i_state & flags) == flags) ||
-	    (dirtytime && (inode->i_state & I_DIRTY_INODE)))
+	if ((inode->i_state & flags) == flags)
 		return;
 
 	spin_lock(&inode->i_lock);
-	if (dirtytime && (inode->i_state & I_DIRTY_INODE))
-		goto out_unlock_inode;
 	if ((inode->i_state & flags) != flags) {
 		const int was_dirty = inode->i_state & I_DIRTY;
 
 		inode_attach_wb(inode, NULL);
 
-		/* I_DIRTY_INODE supersedes I_DIRTY_TIME. */
-		if (flags & I_DIRTY_INODE)
-			inode->i_state &= ~I_DIRTY_TIME;
 		inode->i_state |= flags;
 
 		/*
+		 * Grab inode's wb early because it requires dropping i_lock and we
+		 * need to make sure following checks happen atomically with dirty
+		 * list handling so that we don't move inodes under flush worker's
+		 * hands.
+		 */
+		if (!was_dirty) {
+			wb = locked_inode_to_wb_and_lock_list(inode);
+			spin_lock(&inode->i_lock);
+		}
+
+		/*
 		 * If the inode is queued for writeback by flush worker, just
 		 * update its dirty state. Once the flush worker is done with
 		 * the inode it will place it on the appropriate superblock
 		 * list, based upon its state.
 		 */
 		if (inode->i_state & I_SYNC_QUEUED)
-			goto out_unlock_inode;
+			goto out_unlock;
 
 		/*
 		 * Only add valid (hashed) inodes to the superblock's
@@ -2448,22 +2520,19 @@
 		 */
 		if (!S_ISBLK(inode->i_mode)) {
 			if (inode_unhashed(inode))
-				goto out_unlock_inode;
+				goto out_unlock;
 		}
 		if (inode->i_state & I_FREEING)
-			goto out_unlock_inode;
+			goto out_unlock;
 
 		/*
 		 * If the inode was already on b_dirty/b_io/b_more_io, don't
 		 * reposition it (that would break b_dirty time-ordering).
 		 */
 		if (!was_dirty) {
-			struct bdi_writeback *wb;
 			struct list_head *dirty_list;
 			bool wakeup_bdi = false;
 
-			wb = locked_inode_to_wb_and_lock_list(inode);
-
 			inode->dirtied_when = jiffies;
 			if (dirtytime)
 				inode->dirtied_time_when = jiffies;
@@ -2477,6 +2546,7 @@
 							       dirty_list);
 
 			spin_unlock(&wb->list_lock);
+			spin_unlock(&inode->i_lock);
 			trace_writeback_dirty_inode_enqueue(inode);
 
 			/*
@@ -2491,7 +2561,9 @@
 			return;
 		}
 	}
-out_unlock_inode:
+out_unlock:
+	if (wb)
+		spin_unlock(&wb->list_lock);
 	spin_unlock(&inode->i_lock);
 }
 EXPORT_SYMBOL(__mark_inode_dirty);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fs_context.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fs_context.c
@@ -548,7 +548,7 @@
 			      param->key);
 	}
 
-	if (len > PAGE_SIZE - 2 - size)
+	if (len > PAGE_SIZE || size + len + 2 > PAGE_SIZE)
 		return invalf(fc, "VFS: Legacy: Cumulative options too large");
 	if (strchr(param->key, ',') ||
 	    (param->type == fs_value_is_string &&
@@ -561,7 +561,8 @@
 			return -ENOMEM;
 	}
 
-	ctx->legacy_data[size++] = ',';
+	if (size)
+		ctx->legacy_data[size++] = ',';
 	len = strlen(param->key);
 	memcpy(ctx->legacy_data + size, param->key, len);
 	size += len;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/control.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/control.c
@@ -275,7 +275,7 @@
 	struct dentry *parent;
 	char name[32];
 
-	if (!fuse_control_sb)
+	if (!fuse_control_sb || fc->no_control)
 		return 0;
 
 	parent = fuse_control_sb->s_root;
@@ -313,7 +313,7 @@
 {
 	int i;
 
-	if (!fuse_control_sb)
+	if (!fuse_control_sb || fc->no_control)
 		return;
 
 	for (i = fc->ctl_ndents - 1; i >= 0; i--) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/cuse.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/cuse.c
@@ -474,8 +474,7 @@
 
 static void cuse_fc_release(struct fuse_conn *fc)
 {
-	struct cuse_conn *cc = fc_to_cc(fc);
-	kfree_rcu(cc, fc.rcu);
+	kfree(fc_to_cc(fc));
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/dax.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/dax.c
@@ -681,7 +681,6 @@
 			0, 0, fuse_wait_dax_page(inode));
 }
 
-/* dmap_end == 0 leads to unmapping of whole file */
 int fuse_dax_break_layouts(struct inode *inode, u64 dmap_start,
 				  u64 dmap_end)
 {
@@ -1227,6 +1226,7 @@
 	if (fc->dax) {
 		fuse_free_dax_mem_ranges(&fc->dax->free_ranges);
 		kfree(fc->dax);
+		fc->dax = NULL;
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/dev.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/dev.c
@@ -852,6 +852,12 @@
 	if (!(buf->flags & PIPE_BUF_FLAG_LRU))
 		lru_cache_add(newpage);
 
+	/*
+	 * Release while we have extra ref on stolen page.  Otherwise
+	 * anon_pipe_buf_release() might think the page can be reused.
+	 */
+	pipe_buf_release(cs->pipe, buf);
+
 	err = 0;
 	spin_lock(&cs->req->waitq.lock);
 	if (test_bit(FR_ABORTED, &cs->req->flags))
@@ -935,7 +941,17 @@
 
 	while (count) {
 		if (cs->write && cs->pipebufs && page) {
-			return fuse_ref_page(cs, page, offset, count);
+			/*
+			 * Can't control lifetime of pipe buffers, so always
+			 * copy user pages.
+			 */
+			if (cs->req->args->user_pages) {
+				err = fuse_copy_fill(cs);
+				if (err)
+					return err;
+			} else {
+				return fuse_ref_page(cs, page, offset, count);
+			}
 		} else if (!cs->len) {
 			if (cs->move_pages && page &&
 			    offset == 0 && count == PAGE_SIZE) {
@@ -1607,9 +1623,11 @@
 
 		this_num = min_t(unsigned, num, PAGE_SIZE - offset);
 		err = fuse_copy_page(cs, &page, offset, this_num, 0);
-		if (!err && offset == 0 &&
-		    (this_num == PAGE_SIZE || file_size == end))
+		if (!PageUptodate(page) && !err && offset == 0 &&
+		    (this_num == PAGE_SIZE || file_size == end)) {
+			zero_user_segment(page, this_num, PAGE_SIZE);
 			SetPageUptodate(page);
+		}
 		unlock_page(page);
 		put_page(page);
 
@@ -2031,8 +2049,12 @@
 
 	pipe_lock(pipe);
 out_free:
-	for (idx = 0; idx < nbuf; idx++)
-		pipe_buf_release(pipe, &bufs[idx]);
+	for (idx = 0; idx < nbuf; idx++) {
+		struct pipe_buffer *buf = &bufs[idx];
+
+		if (buf->ops)
+			pipe_buf_release(pipe, buf);
+	}
 	pipe_unlock(pipe);
 
 	kvfree(bufs);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/dir.c
@@ -205,7 +205,7 @@
 	if (inode && fuse_is_bad(inode))
 		goto invalid;
 	else if (time_before64(fuse_dentry_time(entry), get_jiffies_64()) ||
-		 (flags & (LOOKUP_EXCL | LOOKUP_REVAL))) {
+		 (flags & (LOOKUP_EXCL | LOOKUP_REVAL | LOOKUP_RENAME_TARGET))) {
 		struct fuse_entry_out outarg;
 		FUSE_ARGS(args);
 		struct fuse_forget_link *forget;
@@ -249,7 +249,7 @@
 			spin_unlock(&fi->lock);
 		}
 		kfree(forget);
-		if (ret == -ENOMEM)
+		if (ret == -ENOMEM || ret == -EINTR)
 			goto out;
 		if (ret || fuse_invalid_attr(&outarg.attr) ||
 		    fuse_stale_inode(inode, outarg.generation, &outarg.attr))
@@ -390,6 +390,10 @@
 		goto out_put_forget;
 	if (fuse_invalid_attr(&outarg->attr))
 		goto out_put_forget;
+	if (outarg->nodeid == FUSE_ROOT_ID && outarg->generation != 0) {
+		pr_warn_once("root generation should be zero\n");
+		outarg->generation = 0;
+	}
 
 	*inode = fuse_iget(sb, outarg->nodeid, outarg->generation,
 			   &outarg->attr, entry_attr_timeout(outarg),
@@ -476,6 +480,7 @@
 	struct fuse_entry_out outentry;
 	struct fuse_inode *fi;
 	struct fuse_file *ff;
+	bool trunc = flags & O_TRUNC;
 
 	/* Userspace expects S_IFREG in create mode */
 	BUG_ON((mode & S_IFMT) != S_IFREG);
@@ -500,7 +505,7 @@
 	inarg.mode = mode;
 	inarg.umask = current_umask();
 
-	if (fm->fc->handle_killpriv_v2 && (flags & O_TRUNC) &&
+	if (fm->fc->handle_killpriv_v2 && trunc &&
 	    !(flags & O_EXCL) && !capable(CAP_FSETID)) {
 		inarg.open_flags |= FUSE_OPEN_KILL_SUIDGID;
 	}
@@ -549,6 +554,10 @@
 	} else {
 		file->private_data = ff;
 		fuse_finish_open(inode, file);
+		if (fm->fc->atomic_o_trunc && trunc)
+			truncate_pagecache(inode, 0);
+		else if (!(ff->open_flags & FOPEN_KEEP_CACHE))
+			invalidate_inode_pages2(inode->i_mapping);
 	}
 	return err;
 
@@ -738,11 +747,19 @@
 	return create_new_entry(fm, &args, dir, entry, S_IFLNK);
 }
 
+void fuse_flush_time_update(struct inode *inode)
+{
+	int err = sync_inode_metadata(inode, 1);
+
+	mapping_set_error(inode->i_mapping, err);
+}
+
 void fuse_update_ctime(struct inode *inode)
 {
 	if (!IS_NOCMTIME(inode)) {
 		inode->i_ctime = current_time(inode);
 		mark_inode_dirty_sync(inode);
+		fuse_flush_time_update(inode);
 	}
 }
 
@@ -1071,7 +1088,7 @@
 	if (!parent)
 		return -ENOENT;
 
-	inode_lock(parent);
+	inode_lock_nested(parent, I_MUTEX_PARENT);
 	if (!S_ISDIR(parent->i_mode))
 		goto unlock;
 
@@ -1316,7 +1333,7 @@
 		goto out_err;
 
 	if (fc->cache_symlinks)
-		return page_get_link(dentry, inode, callback);
+		return page_get_link_raw(dentry, inode, callback);
 
 	err = -ECHILD;
 	if (!dentry)
@@ -1583,7 +1600,7 @@
 	if (FUSE_IS_DAX(inode) && is_truncate) {
 		filemap_invalidate_lock(mapping);
 		fault_blocked = true;
-		err = fuse_dax_break_layouts(inode, 0, 0);
+		err = fuse_dax_break_layouts(inode, 0, -1);
 		if (err) {
 			filemap_invalidate_unlock(mapping);
 			return err;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/file.c
@@ -210,12 +210,9 @@
 		fi->attr_version = atomic64_inc_return(&fc->attr_version);
 		i_size_write(inode, 0);
 		spin_unlock(&fi->lock);
-		truncate_pagecache(inode, 0);
 		fuse_invalidate_attr(inode);
 		if (fc->writeback_cache)
 			file_update_time(file);
-	} else if (!(ff->open_flags & FOPEN_KEEP_CACHE)) {
-		invalidate_inode_pages2(inode->i_mapping);
 	}
 
 	if ((file->f_mode & FMODE_WRITE) && fc->writeback_cache)
@@ -240,30 +237,38 @@
 	if (err)
 		return err;
 
-	if (is_wb_truncate || dax_truncate) {
+	if (is_wb_truncate || dax_truncate)
 		inode_lock(inode);
-		fuse_set_nowrite(inode);
-	}
 
 	if (dax_truncate) {
 		filemap_invalidate_lock(inode->i_mapping);
-		err = fuse_dax_break_layouts(inode, 0, 0);
+		err = fuse_dax_break_layouts(inode, 0, -1);
 		if (err)
-			goto out;
+			goto out_inode_unlock;
 	}
 
+	if (is_wb_truncate || dax_truncate)
+		fuse_set_nowrite(inode);
+
 	err = fuse_do_open(fm, get_node_id(inode), file, isdir);
 	if (!err)
 		fuse_finish_open(inode, file);
 
-out:
+	if (is_wb_truncate || dax_truncate)
+		fuse_release_nowrite(inode);
+	if (!err) {
+		struct fuse_file *ff = file->private_data;
+
+		if (fc->atomic_o_trunc && (file->f_flags & O_TRUNC))
+			truncate_pagecache(inode, 0);
+		else if (!(ff->open_flags & FOPEN_KEEP_CACHE))
+			invalidate_inode_pages2(inode->i_mapping);
+	}
 	if (dax_truncate)
 		filemap_invalidate_unlock(inode->i_mapping);
-
-	if (is_wb_truncate | dax_truncate) {
-		fuse_release_nowrite(inode);
+out_inode_unlock:
+	if (is_wb_truncate || dax_truncate)
 		inode_unlock(inode);
-	}
 
 	return err;
 }
@@ -793,7 +798,7 @@
 	struct fuse_inode *fi = get_fuse_inode(inode);
 
 	spin_lock(&fi->lock);
-	if (attr_ver == fi->attr_version && size < inode->i_size &&
+	if (attr_ver >= fi->attr_version && size < inode->i_size &&
 	    !test_bit(FUSE_I_SIZE_UNSTABLE, &fi->state)) {
 		fi->attr_version = atomic64_inc_return(&fc->attr_version);
 		i_size_write(inode, size);
@@ -1164,7 +1169,7 @@
 
  again:
 		err = -EFAULT;
-		if (iov_iter_fault_in_readable(ii, bytes))
+		if (fault_in_iov_iter_readable(ii, bytes))
 			break;
 
 		err = -ENOMEM;
@@ -1295,7 +1300,7 @@
 			return err;
 
 		if (fc->handle_killpriv_v2 &&
-		    should_remove_suid(file_dentry(file))) {
+		    setattr_should_drop_suidgid(&init_user_ns, file_inode(file))) {
 			goto writethrough;
 		}
 
@@ -1417,6 +1422,7 @@
 			(PAGE_SIZE - ret) & (PAGE_SIZE - 1);
 	}
 
+	ap->args.user_pages = true;
 	if (write)
 		ap->args.in_pages = true;
 	else
@@ -1688,10 +1694,16 @@
 	fuse_writepage_finish(fm, wpa);
 	spin_unlock(&fi->lock);
 
-	/* After fuse_writepage_finish() aux request list is private */
+	/* After rb_erase() aux request list is private */
 	for (aux = wpa->next; aux; aux = next) {
+		struct backing_dev_info *bdi = inode_to_bdi(aux->inode);
+
 		next = aux->next;
 		aux->next = NULL;
+
+		dec_wb_stat(&bdi->wb, WB_WRITEBACK);
+		dec_node_page_state(aux->ia.ap.pages[0], NR_WRITEBACK_TEMP);
+		wb_writeout_inc(&bdi->wb);
 		fuse_writepage_free(aux);
 	}
 
@@ -1848,6 +1860,17 @@
 	struct fuse_file *ff;
 	int err;
 
+	/*
+	 * Inode is always written before the last reference is dropped and
+	 * hence this should not be reached from reclaim.
+	 *
+	 * Writing back the inode from reclaim can deadlock if the request
+	 * processing itself needs an allocation.  Allocations triggering
+	 * reclaim while serving a request can't be prevented, because it can
+	 * involve any number of unrelated userspace processes.
+	 */
+	WARN_ON(wbc->for_reclaim);
+
 	ff = __fuse_write_file_get(fi);
 	err = fuse_flush_times(inode, ff);
 	if (ff)
@@ -2902,7 +2925,7 @@
 
 static int fuse_writeback_range(struct inode *inode, loff_t start, loff_t end)
 {
-	int err = filemap_write_and_wait_range(inode->i_mapping, start, -1);
+	int err = filemap_write_and_wait_range(inode->i_mapping, start, LLONG_MAX);
 
 	if (!err)
 		fuse_sync_writes(inode);
@@ -2925,11 +2948,9 @@
 		.mode = mode
 	};
 	int err;
-	bool lock_inode = !(mode & FALLOC_FL_KEEP_SIZE) ||
-			   (mode & (FALLOC_FL_PUNCH_HOLE |
-				    FALLOC_FL_ZERO_RANGE));
-
-	bool block_faults = FUSE_IS_DAX(inode) && lock_inode;
+	bool block_faults = FUSE_IS_DAX(inode) &&
+		(!(mode & FALLOC_FL_KEEP_SIZE) ||
+		 (mode & (FALLOC_FL_PUNCH_HOLE | FALLOC_FL_ZERO_RANGE)));
 
 	if (mode & ~(FALLOC_FL_KEEP_SIZE | FALLOC_FL_PUNCH_HOLE |
 		     FALLOC_FL_ZERO_RANGE))
@@ -2938,22 +2959,20 @@
 	if (fm->fc->no_fallocate)
 		return -EOPNOTSUPP;
 
-	if (lock_inode) {
-		inode_lock(inode);
-		if (block_faults) {
-			filemap_invalidate_lock(inode->i_mapping);
-			err = fuse_dax_break_layouts(inode, 0, 0);
-			if (err)
-				goto out;
-		}
+	inode_lock(inode);
+	if (block_faults) {
+		filemap_invalidate_lock(inode->i_mapping);
+		err = fuse_dax_break_layouts(inode, 0, -1);
+		if (err)
+			goto out;
+	}
 
-		if (mode & (FALLOC_FL_PUNCH_HOLE | FALLOC_FL_ZERO_RANGE)) {
-			loff_t endbyte = offset + length - 1;
-
-			err = fuse_writeback_range(inode, offset, endbyte);
-			if (err)
-				goto out;
-		}
+	if (mode & (FALLOC_FL_PUNCH_HOLE | FALLOC_FL_ZERO_RANGE)) {
+		loff_t endbyte = offset + length - 1;
+
+		err = fuse_writeback_range(inode, offset, endbyte);
+		if (err)
+			goto out;
 	}
 
 	if (!(mode & FALLOC_FL_KEEP_SIZE) &&
@@ -2963,6 +2982,10 @@
 			goto out;
 	}
 
+	err = file_modified(file);
+	if (err)
+		goto out;
+
 	if (!(mode & FALLOC_FL_KEEP_SIZE))
 		set_bit(FUSE_I_SIZE_UNSTABLE, &fi->state);
 
@@ -2999,8 +3022,9 @@
 	if (block_faults)
 		filemap_invalidate_unlock(inode->i_mapping);
 
-	if (lock_inode)
-		inode_unlock(inode);
+	inode_unlock(inode);
+
+	fuse_flush_time_update(inode);
 
 	return err;
 }
@@ -3111,6 +3135,8 @@
 	inode_unlock(inode_out);
 	file_accessed(file_in);
 
+	fuse_flush_time_update(inode_out);
+
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/fuse_i.h
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/fuse_i.h
@@ -63,6 +63,19 @@
 	struct fuse_forget_link *next;
 };
 
+/* Submount lookup tracking */
+struct fuse_submount_lookup {
+	/** Refcount */
+	refcount_t count;
+
+	/** Unique ID, which identifies the inode between userspace
+	 * and kernel */
+	u64 nodeid;
+
+	/** The request used for sending the FORGET message */
+	struct fuse_forget_link *forget;
+};
+
 /** FUSE inode */
 struct fuse_inode {
 	/** Inode data */
@@ -155,6 +168,8 @@
 	 */
 	struct fuse_inode_dax *dax;
 #endif
+	/** Submount specific lookup tracking */
+	struct fuse_submount_lookup *submount_lookup;
 };
 
 /** FUSE inode state bits */
@@ -256,6 +271,7 @@
 	bool nocreds:1;
 	bool in_pages:1;
 	bool out_pages:1;
+	bool user_pages:1;
 	bool out_argvar:1;
 	bool page_zeroing:1;
 	bool page_replace:1;
@@ -832,6 +848,7 @@
 
 	/* Entry on fc->mounts */
 	struct list_head fc_entry;
+	struct rcu_head rcu;
 };
 
 static inline struct fuse_mount *get_fuse_mount_super(struct super_block *sb)
@@ -883,7 +900,6 @@
 
 static inline void fuse_make_bad(struct inode *inode)
 {
-	remove_inode_hash(inode);
 	set_bit(FUSE_I_BAD, &get_fuse_inode(inode)->state);
 }
 
@@ -1148,6 +1164,7 @@
 
 u64 fuse_lock_owner_id(struct fuse_conn *fc, fl_owner_t id);
 
+void fuse_flush_time_update(struct inode *inode);
 void fuse_update_ctime(struct inode *inode);
 
 int fuse_update_attributes(struct inode *inode, struct file *file);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/inode.c
@@ -69,6 +69,24 @@
 	return kzalloc(sizeof(struct fuse_forget_link), GFP_KERNEL_ACCOUNT);
 }
 
+static struct fuse_submount_lookup *fuse_alloc_submount_lookup(void)
+{
+	struct fuse_submount_lookup *sl;
+
+	sl = kzalloc(sizeof(struct fuse_submount_lookup), GFP_KERNEL_ACCOUNT);
+	if (!sl)
+		return NULL;
+	sl->forget = fuse_alloc_forget();
+	if (!sl->forget)
+		goto out_free;
+
+	return sl;
+
+out_free:
+	kfree(sl);
+	return NULL;
+}
+
 static struct inode *fuse_alloc_inode(struct super_block *sb)
 {
 	struct fuse_inode *fi;
@@ -84,6 +102,7 @@
 	fi->attr_version = 0;
 	fi->orig_ino = 0;
 	fi->state = 0;
+	fi->submount_lookup = NULL;
 	mutex_init(&fi->mutex);
 	spin_lock_init(&fi->lock);
 	fi->forget = fuse_alloc_forget();
@@ -114,10 +133,24 @@
 	kmem_cache_free(fuse_inode_cachep, fi);
 }
 
+static void fuse_cleanup_submount_lookup(struct fuse_conn *fc,
+					 struct fuse_submount_lookup *sl)
+{
+	if (!refcount_dec_and_test(&sl->count))
+		return;
+
+	fuse_queue_forget(fc, sl->forget, sl->nodeid, 1);
+	sl->forget = NULL;
+	kfree(sl);
+}
+
 static void fuse_evict_inode(struct inode *inode)
 {
 	struct fuse_inode *fi = get_fuse_inode(inode);
 
+	/* Will write inode on close/munmap and in all other dirtiers */
+	WARN_ON(inode->i_state & I_DIRTY_INODE);
+
 	truncate_inode_pages_final(&inode->i_data);
 	clear_inode(inode);
 	if (inode->i_sb->s_flags & SB_ACTIVE) {
@@ -130,6 +163,11 @@
 					  fi->nlookup);
 			fi->forget = NULL;
 		}
+
+		if (fi->submount_lookup) {
+			fuse_cleanup_submount_lookup(fc, fi->submount_lookup);
+			fi->submount_lookup = NULL;
+		}
 	}
 	if (S_ISREG(inode->i_mode) && !fuse_is_bad(inode)) {
 		WARN_ON(!list_empty(&fi->write_files));
@@ -178,6 +216,12 @@
 	inode->i_uid     = make_kuid(fc->user_ns, attr->uid);
 	inode->i_gid     = make_kgid(fc->user_ns, attr->gid);
 	inode->i_blocks  = attr->blocks;
+
+	/* Sanitize nsecs */
+	attr->atimensec = min_t(u32, attr->atimensec, NSEC_PER_SEC - 1);
+	attr->mtimensec = min_t(u32, attr->mtimensec, NSEC_PER_SEC - 1);
+	attr->ctimensec = min_t(u32, attr->ctimensec, NSEC_PER_SEC - 1);
+
 	inode->i_atime.tv_sec   = attr->atime;
 	inode->i_atime.tv_nsec  = attr->atimensec;
 	/* mtime from server may be stale due to local buffered write */
@@ -270,6 +314,13 @@
 	}
 }
 
+static void fuse_init_submount_lookup(struct fuse_submount_lookup *sl,
+				      u64 nodeid)
+{
+	sl->nodeid = nodeid;
+	refcount_set(&sl->count, 1);
+}
+
 static void fuse_init_inode(struct inode *inode, struct fuse_attr *attr)
 {
 	inode->i_mode = attr->mode & S_IFMT;
@@ -327,12 +378,22 @@
 	 */
 	if (fc->auto_submounts && (attr->flags & FUSE_ATTR_SUBMOUNT) &&
 	    S_ISDIR(attr->mode)) {
+		struct fuse_inode *fi;
+
 		inode = new_inode(sb);
 		if (!inode)
 			return NULL;
 
 		fuse_init_inode(inode, attr);
-		get_fuse_inode(inode)->nodeid = nodeid;
+		fi = get_fuse_inode(inode);
+		fi->nodeid = nodeid;
+		fi->submount_lookup = fuse_alloc_submount_lookup();
+		if (!fi->submount_lookup) {
+			iput(inode);
+			return NULL;
+		}
+		/* Sets nlookup = 1 on fi->submount_lookup->nlookup */
+		fuse_init_submount_lookup(fi->submount_lookup, nodeid);
 		inode->i_flags |= S_AUTOMOUNT;
 		goto done;
 	}
@@ -352,14 +413,17 @@
 	} else if (fuse_stale_inode(inode, generation, attr)) {
 		/* nodeid was reused, any I/O on the old inode should fail */
 		fuse_make_bad(inode);
-		iput(inode);
-		goto retry;
+		if (inode != d_inode(sb->s_root)) {
+			remove_inode_hash(inode);
+			iput(inode);
+			goto retry;
+		}
 	}
-done:
 	fi = get_fuse_inode(inode);
 	spin_lock(&fi->lock);
 	fi->nlookup++;
 	spin_unlock(&fi->lock);
+done:
 	fuse_change_attributes(inode, attr, attr_valid, attr_version);
 
 	return inode;
@@ -622,6 +686,8 @@
 	struct fs_parse_result result;
 	struct fuse_fs_context *ctx = fsc->fs_private;
 	int opt;
+	kuid_t kuid;
+	kgid_t kgid;
 
 	if (fsc->purpose == FS_CONTEXT_FOR_RECONFIGURE) {
 		/*
@@ -666,16 +732,30 @@
 		break;
 
 	case OPT_USER_ID:
-		ctx->user_id = make_kuid(fsc->user_ns, result.uint_32);
-		if (!uid_valid(ctx->user_id))
+		kuid =  make_kuid(fsc->user_ns, result.uint_32);
+		if (!uid_valid(kuid))
 			return invalfc(fsc, "Invalid user_id");
+		/*
+		 * The requested uid must be representable in the
+		 * filesystem's idmapping.
+		 */
+		if (!kuid_has_mapping(fsc->user_ns, kuid))
+			return invalfc(fsc, "Invalid user_id");
+		ctx->user_id = kuid;
 		ctx->user_id_present = true;
 		break;
 
 	case OPT_GROUP_ID:
-		ctx->group_id = make_kgid(fsc->user_ns, result.uint_32);
-		if (!gid_valid(ctx->group_id))
+		kgid = make_kgid(fsc->user_ns, result.uint_32);;
+		if (!gid_valid(kgid))
+			return invalfc(fsc, "Invalid group_id");
+		/*
+		 * The requested gid must be representable in the
+		 * filesystem's idmapping.
+		 */
+		if (!kgid_has_mapping(fsc->user_ns, kgid))
 			return invalfc(fsc, "Invalid group_id");
+		ctx->group_id = kgid;
 		ctx->group_id_present = true;
 		break;
 
@@ -803,6 +883,14 @@
 }
 EXPORT_SYMBOL_GPL(fuse_conn_init);
 
+static void delayed_release(struct rcu_head *p)
+{
+	struct fuse_conn *fc = container_of(p, struct fuse_conn, rcu);
+
+	put_user_ns(fc->user_ns);
+	fc->release(fc);
+}
+
 void fuse_conn_put(struct fuse_conn *fc)
 {
 	if (refcount_dec_and_test(&fc->count)) {
@@ -814,13 +902,12 @@
 		if (fiq->ops->release)
 			fiq->ops->release(fiq);
 		put_pid_ns(fc->pid_ns);
-		put_user_ns(fc->user_ns);
 		bucket = rcu_dereference_protected(fc->curr_bucket, 1);
 		if (bucket) {
 			WARN_ON(atomic_read(&bucket->count) != 1);
 			kfree(bucket);
 		}
-		fc->release(fc);
+		call_rcu(&fc->rcu, delayed_release);
 	}
 }
 EXPORT_SYMBOL_GPL(fuse_conn_put);
@@ -1217,7 +1304,7 @@
 void fuse_free_conn(struct fuse_conn *fc)
 {
 	WARN_ON(!list_empty(&fc->devices));
-	kfree_rcu(fc, rcu);
+	kfree(fc);
 }
 EXPORT_SYMBOL_GPL(fuse_free_conn);
 
@@ -1371,6 +1458,8 @@
 	struct super_block *parent_sb = parent_fi->inode.i_sb;
 	struct fuse_attr root_attr;
 	struct inode *root;
+	struct fuse_submount_lookup *sl;
+	struct fuse_inode *fi;
 
 	fuse_sb_defaults(sb);
 	fm->sb = sb;
@@ -1393,12 +1482,27 @@
 	 * its nlookup should not be incremented.  fuse_iget() does
 	 * that, though, so undo it here.
 	 */
-	get_fuse_inode(root)->nlookup--;
+	fi = get_fuse_inode(root);
+	fi->nlookup--;
+
 	sb->s_d_op = &fuse_dentry_operations;
 	sb->s_root = d_make_root(root);
 	if (!sb->s_root)
 		return -ENOMEM;
 
+	/*
+	 * Grab the parent's submount_lookup pointer and take a
+	 * reference on the shared nlookup from the parent.  This is to
+	 * prevent the last forget for this nodeid from getting
+	 * triggered until all users have finished with it.
+	 */
+	sl = parent_fi->submount_lookup;
+	WARN_ON(!sl);
+	if (sl) {
+		refcount_inc(&sl->count);
+		fi->submount_lookup = sl;
+	}
+
 	return 0;
 }
 
@@ -1739,7 +1843,7 @@
 void fuse_mount_destroy(struct fuse_mount *fm)
 {
 	fuse_conn_put(fm->fc);
-	kfree(fm);
+	kfree_rcu(fm, rcu);
 }
 EXPORT_SYMBOL(fuse_mount_destroy);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/ioctl.c
@@ -9,6 +9,26 @@
 #include <linux/compat.h>
 #include <linux/fileattr.h>
 
+static ssize_t fuse_send_ioctl(struct fuse_mount *fm, struct fuse_args *args,
+			       struct fuse_ioctl_out *outarg)
+{
+	ssize_t ret;
+
+	args->out_args[0].size = sizeof(*outarg);
+	args->out_args[0].value = outarg;
+
+	ret = fuse_simple_request(fm, args);
+
+	/* Translate ENOSYS, which shouldn't be returned from fs */
+	if (ret == -ENOSYS)
+		ret = -ENOTTY;
+
+	if (ret >= 0 && outarg->result == -ENOSYS)
+		outarg->result = -ENOTTY;
+
+	return ret;
+}
+
 /*
  * CUSE servers compiled on 32bit broke on 64bit kernels because the
  * ABI was defined to be 'struct iovec' which is different on 32bit
@@ -253,13 +273,11 @@
 	}
 
 	ap.args.out_numargs = 2;
-	ap.args.out_args[0].size = sizeof(outarg);
-	ap.args.out_args[0].value = &outarg;
 	ap.args.out_args[1].size = out_size;
 	ap.args.out_pages = true;
 	ap.args.out_argvar = true;
 
-	transferred = fuse_simple_request(fm, &ap.args);
+	transferred = fuse_send_ioctl(fm, &ap.args, &outarg);
 	err = transferred;
 	if (transferred < 0)
 		goto out;
@@ -388,15 +406,16 @@
 	args.in_args[1].size = inarg.in_size;
 	args.in_args[1].value = ptr;
 	args.out_numargs = 2;
-	args.out_args[0].size = sizeof(outarg);
-	args.out_args[0].value = &outarg;
 	args.out_args[1].size = inarg.out_size;
 	args.out_args[1].value = ptr;
 
-	err = fuse_simple_request(fm, &args);
-	if (!err && outarg.flags & FUSE_IOCTL_RETRY)
-		err = -EIO;
-
+	err = fuse_send_ioctl(fm, &args, &outarg);
+	if (!err) {
+		if (outarg.result < 0)
+			err = outarg.result;
+		else if (outarg.flags & FUSE_IOCTL_RETRY)
+			err = -EIO;
+	}
 	return err;
 }
 
@@ -405,6 +424,12 @@
 	struct fuse_mount *fm = get_fuse_mount(inode);
 	bool isdir = S_ISDIR(inode->i_mode);
 
+	if (!fuse_allow_current_process(fm->fc))
+		return ERR_PTR(-EACCES);
+
+	if (fuse_is_bad(inode))
+		return ERR_PTR(-EIO);
+
 	if (!S_ISREG(inode->i_mode) && !isdir)
 		return ERR_PTR(-ENOTTY);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/readdir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/readdir.c
@@ -77,8 +77,10 @@
 		goto unlock;
 
 	addr = kmap_atomic(page);
-	if (!offset)
+	if (!offset) {
 		clear_page(addr);
+		SetPageUptodate(page);
+	}
 	memcpy(addr + offset, dirent, reclen);
 	kunmap_atomic(addr);
 	fi->rdc.size = (index << PAGE_SHIFT) + offset + reclen;
@@ -241,8 +243,16 @@
 			dput(dentry);
 			dentry = alias;
 		}
-		if (IS_ERR(dentry))
+		if (IS_ERR(dentry)) {
+			if (!IS_ERR(inode)) {
+				struct fuse_inode *fi = get_fuse_inode(inode);
+
+				spin_lock(&fi->lock);
+				fi->nlookup--;
+				spin_unlock(&fi->lock);
+			}
 			return PTR_ERR(dentry);
+		}
 	}
 	if (fc->readdirplus_auto)
 		set_bit(FUSE_I_INIT_RDPLUS, &get_fuse_inode(inode)->state);
@@ -516,6 +526,12 @@
 
 	page = find_get_page_flags(file->f_mapping, index,
 				   FGP_ACCESSED | FGP_LOCK);
+	/* Page gone missing, then re-added to cache, but not initialized? */
+	if (page && !PageUptodate(page)) {
+		unlock_page(page);
+		put_page(page);
+		page = NULL;
+	}
 	spin_lock(&fi->rdc.lock);
 	if (!page) {
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/virtio_fs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/virtio_fs.c
@@ -310,6 +310,16 @@
 		return -ENOMEM;
 	memcpy(fs->tag, tag_buf, len);
 	fs->tag[len] = '\0';
+
+	/* While the VIRTIO specification allows any character, newlines are
+	 * awkward on mount(8) command-lines and cause problems in the sysfs
+	 * "tag" attr and uevent TAG= properties. Forbid them.
+	 */
+	if (strchr(fs->tag, '\n')) {
+		dev_dbg(&vdev->dev, "refusing virtiofs tag with newline character\n");
+		return -EINVAL;
+	}
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/fuse/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/fuse/xattr.c
@@ -82,7 +82,7 @@
 	}
 	ret = fuse_simple_request(fm, &args);
 	if (!ret && !size)
-		ret = min_t(ssize_t, outarg.size, XATTR_SIZE_MAX);
+		ret = min_t(size_t, outarg.size, XATTR_SIZE_MAX);
 	if (ret == -ENOSYS) {
 		fm->fc->no_getxattr = 1;
 		ret = -EOPNOTSUPP;
@@ -144,7 +144,7 @@
 	}
 	ret = fuse_simple_request(fm, &args);
 	if (!ret && !size)
-		ret = min_t(ssize_t, outarg.size, XATTR_LIST_MAX);
+		ret = min_t(size_t, outarg.size, XATTR_LIST_MAX);
 	if (ret > 0 && size)
 		ret = fuse_verify_xattr_list(list, ret);
 	if (ret == -ENOSYS) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/aops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/aops.c
@@ -152,7 +152,6 @@
 {
 	struct inode *inode = page->mapping->host;
 	struct gfs2_inode *ip = GFS2_I(inode);
-	struct gfs2_sbd *sdp = GFS2_SB(inode);
 
 	if (PageChecked(page)) {
 		ClearPageChecked(page);
@@ -160,7 +159,7 @@
 			create_empty_buffers(page, inode->i_sb->s_blocksize,
 					     BIT(BH_Dirty)|BIT(BH_Uptodate));
 		}
-		gfs2_page_add_databufs(ip, page, 0, sdp->sd_vfs->s_blocksize);
+		gfs2_page_add_databufs(ip, page, 0, PAGE_SIZE);
 	}
 	return gfs2_write_jdata_page(page, wbc);
 }
@@ -208,13 +207,13 @@
 	int ret;
 
 	/*
-	 * Even if we didn't write any pages here, we might still be holding
+	 * Even if we didn't write enough pages here, we might still be holding
 	 * dirty pages in the ail. We forcibly flush the ail because we don't
 	 * want balance_dirty_pages() to loop indefinitely trying to write out
 	 * pages held in the ail that it can't find.
 	 */
 	ret = iomap_writepages(mapping, wbc, &wpc, &gfs2_writeback_ops);
-	if (ret == 0)
+	if (ret == 0 && wbc->nr_to_write > 0)
 		set_bit(SDF_FORCE_AIL_FLUSH, &sdp->sd_flags);
 	return ret;
 }
@@ -452,8 +451,6 @@
 		return error;
 
 	kaddr = kmap_atomic(page);
-	if (dsize > gfs2_max_stuffed_size(ip))
-		dsize = gfs2_max_stuffed_size(ip);
 	memcpy(kaddr, dibh->b_data + sizeof(struct gfs2_dinode), dsize);
 	memset(kaddr + dsize, 0, PAGE_SIZE - dsize);
 	kunmap_atomic(kaddr);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/bmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/bmap.c
@@ -61,9 +61,6 @@
 		void *kaddr = kmap(page);
 		u64 dsize = i_size_read(inode);
  
-		if (dsize > gfs2_max_stuffed_size(ip))
-			dsize = gfs2_max_stuffed_size(ip);
-
 		memcpy(kaddr, dibh->b_data + sizeof(struct gfs2_dinode), dsize);
 		memset(kaddr + dsize, 0, PAGE_SIZE - dsize);
 		kunmap(page);
@@ -940,7 +937,7 @@
 		else if (height == ip->i_height)
 			ret = gfs2_hole_size(inode, lblock, len, mp, iomap);
 		else
-			iomap->length = size - pos;
+			iomap->length = size - iomap->offset;
 	} else if (flags & IOMAP_WRITE) {
 		u64 alloc_size;
 
@@ -961,46 +958,6 @@
 	goto out;
 }
 
-static int gfs2_write_lock(struct inode *inode)
-{
-	struct gfs2_inode *ip = GFS2_I(inode);
-	struct gfs2_sbd *sdp = GFS2_SB(inode);
-	int error;
-
-	gfs2_holder_init(ip->i_gl, LM_ST_EXCLUSIVE, 0, &ip->i_gh);
-	error = gfs2_glock_nq(&ip->i_gh);
-	if (error)
-		goto out_uninit;
-	if (&ip->i_inode == sdp->sd_rindex) {
-		struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
-
-		error = gfs2_glock_nq_init(m_ip->i_gl, LM_ST_EXCLUSIVE,
-					   GL_NOCACHE, &m_ip->i_gh);
-		if (error)
-			goto out_unlock;
-	}
-	return 0;
-
-out_unlock:
-	gfs2_glock_dq(&ip->i_gh);
-out_uninit:
-	gfs2_holder_uninit(&ip->i_gh);
-	return error;
-}
-
-static void gfs2_write_unlock(struct inode *inode)
-{
-	struct gfs2_inode *ip = GFS2_I(inode);
-	struct gfs2_sbd *sdp = GFS2_SB(inode);
-
-	if (&ip->i_inode == sdp->sd_rindex) {
-		struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
-
-		gfs2_glock_dq_uninit(&m_ip->i_gh);
-	}
-	gfs2_glock_dq_uninit(&ip->i_gh);
-}
-
 static int gfs2_iomap_page_prepare(struct inode *inode, loff_t pos,
 				   unsigned len)
 {
@@ -1118,11 +1075,6 @@
 	return ret;
 }
 
-static inline bool gfs2_iomap_need_write_lock(unsigned flags)
-{
-	return (flags & IOMAP_WRITE) && !(flags & IOMAP_DIRECT);
-}
-
 static int gfs2_iomap_begin(struct inode *inode, loff_t pos, loff_t length,
 			    unsigned flags, struct iomap *iomap,
 			    struct iomap *srcmap)
@@ -1135,12 +1087,6 @@
 		iomap->flags |= IOMAP_F_BUFFER_HEAD;
 
 	trace_gfs2_iomap_start(ip, pos, length, flags);
-	if (gfs2_iomap_need_write_lock(flags)) {
-		ret = gfs2_write_lock(inode);
-		if (ret)
-			goto out;
-	}
-
 	ret = __gfs2_iomap_get(inode, pos, length, flags, iomap, &mp);
 	if (ret)
 		goto out_unlock;
@@ -1168,10 +1114,7 @@
 	ret = gfs2_iomap_begin_write(inode, pos, length, flags, iomap, &mp);
 
 out_unlock:
-	if (ret && gfs2_iomap_need_write_lock(flags))
-		gfs2_write_unlock(inode);
 	release_metapath(&mp);
-out:
 	trace_gfs2_iomap_end(ip, iomap, ret);
 	return ret;
 }
@@ -1208,26 +1151,21 @@
 
 	if (length != written && (iomap->flags & IOMAP_F_NEW)) {
 		/* Deallocate blocks that were just allocated. */
-		loff_t blockmask = i_blocksize(inode) - 1;
-		loff_t end = (pos + length) & ~blockmask;
+		loff_t hstart = round_up(pos + written, i_blocksize(inode));
+		loff_t hend = iomap->offset + iomap->length;
 
-		pos = (pos + written + blockmask) & ~blockmask;
-		if (pos < end) {
-			truncate_pagecache_range(inode, pos, end - 1);
-			punch_hole(ip, pos, end - pos);
+		if (hstart < hend) {
+			truncate_pagecache_range(inode, hstart, hend - 1);
+			punch_hole(ip, hstart, hend - hstart);
 		}
 	}
 
 	if (unlikely(!written))
-		goto out_unlock;
+		return 0;
 
 	if (iomap->flags & IOMAP_F_SIZE_CHANGED)
 		mark_inode_dirty(inode);
 	set_bit(GLF_DIRTY, &ip->i_gl->gl_flags);
-
-out_unlock:
-	if (gfs2_iomap_need_write_lock(flags))
-		gfs2_write_unlock(inode);
 	return 0;
 }
 
@@ -1766,7 +1704,8 @@
 	struct buffer_head *dibh, *bh;
 	struct gfs2_holder rd_gh;
 	unsigned int bsize_shift = sdp->sd_sb.sb_bsize_shift;
-	u64 lblock = (offset + (1 << bsize_shift) - 1) >> bsize_shift;
+	unsigned int bsize = 1 << bsize_shift;
+	u64 lblock = (offset + bsize - 1) >> bsize_shift;
 	__u16 start_list[GFS2_MAX_META_HEIGHT];
 	__u16 __end_list[GFS2_MAX_META_HEIGHT], *end_list = NULL;
 	unsigned int start_aligned, end_aligned;
@@ -1777,7 +1716,7 @@
 	u64 prev_bnr = 0;
 	__be64 *start, *end;
 
-	if (offset >= maxsize) {
+	if (offset + bsize - 1 >= maxsize) {
 		/*
 		 * The starting point lies beyond the allocated meta-data;
 		 * there are no blocks do deallocate.
@@ -2204,7 +2143,7 @@
 
 	ret = do_shrink(inode, newsize);
 out:
-	gfs2_rs_delete(ip, NULL);
+	gfs2_rs_delete(ip);
 	gfs2_qa_put(ip);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/file.c
@@ -257,6 +257,7 @@
 		error = filemap_fdatawait(inode->i_mapping);
 		if (error)
 			goto out;
+		truncate_inode_pages(inode->i_mapping, 0);
 		if (new_flags & GFS2_DIF_JDATA)
 			gfs2_ordered_del_inode(ip);
 	}
@@ -711,10 +712,11 @@
 	kfree(file->private_data);
 	file->private_data = NULL;
 
-	if (gfs2_rs_active(&ip->i_res))
-		gfs2_rs_delete(ip, &inode->i_writecount);
-	if (file->f_mode & FMODE_WRITE)
+	if (file->f_mode & FMODE_WRITE) {
+		if (gfs2_rs_active(&ip->i_res))
+			gfs2_rs_delete(ip);
 		gfs2_qa_put(ip);
+	}
 	return 0;
 }
 
@@ -776,27 +778,99 @@
 	return ret ? ret : ret1;
 }
 
+static inline bool should_fault_in_pages(ssize_t ret, struct iov_iter *i,
+					 size_t *prev_count,
+					 size_t *window_size)
+{
+	char __user *p = i->iov[0].iov_base + i->iov_offset;
+	size_t count = iov_iter_count(i);
+	int pages = 1;
+
+	if (likely(!count))
+		return false;
+	if (ret <= 0 && ret != -EFAULT)
+		return false;
+	if (!iter_is_iovec(i))
+		return false;
+
+	if (*prev_count != count || !*window_size) {
+		int pages, nr_dirtied;
+
+		pages = min_t(int, BIO_MAX_VECS,
+			      DIV_ROUND_UP(iov_iter_count(i), PAGE_SIZE));
+		nr_dirtied = max(current->nr_dirtied_pause -
+				 current->nr_dirtied, 1);
+		pages = min(pages, nr_dirtied);
+	}
+
+	*prev_count = count;
+	*window_size = (size_t)PAGE_SIZE * pages - offset_in_page(p);
+	return true;
+}
+
 static ssize_t gfs2_file_direct_read(struct kiocb *iocb, struct iov_iter *to,
 				     struct gfs2_holder *gh)
 {
 	struct file *file = iocb->ki_filp;
 	struct gfs2_inode *ip = GFS2_I(file->f_mapping->host);
-	size_t count = iov_iter_count(to);
+	size_t prev_count = 0, window_size = 0;
+	size_t written = 0;
 	ssize_t ret;
 
-	if (!count)
+	/*
+	 * In this function, we disable page faults when we're holding the
+	 * inode glock while doing I/O.  If a page fault occurs, we indicate
+	 * that the inode glock may be dropped, fault in the pages manually,
+	 * and retry.
+	 *
+	 * Unlike generic_file_read_iter, for reads, iomap_dio_rw can trigger
+	 * physical as well as manual page faults, and we need to disable both
+	 * kinds.
+	 *
+	 * For direct I/O, gfs2 takes the inode glock in deferred mode.  This
+	 * locking mode is compatible with other deferred holders, so multiple
+	 * processes and nodes can do direct I/O to a file at the same time.
+	 * There's no guarantee that reads or writes will be atomic.  Any
+	 * coordination among readers and writers needs to happen externally.
+	 */
+
+	if (!iov_iter_count(to))
 		return 0; /* skip atime */
 
 	gfs2_holder_init(ip->i_gl, LM_ST_DEFERRED, 0, gh);
+retry:
 	ret = gfs2_glock_nq(gh);
 	if (ret)
 		goto out_uninit;
+retry_under_glock:
+	pagefault_disable();
+	to->nofault = true;
+	ret = iomap_dio_rw(iocb, to, &gfs2_iomap_ops, NULL,
+			   IOMAP_DIO_PARTIAL, written);
+	to->nofault = false;
+	pagefault_enable();
+	if (ret > 0)
+		written = ret;
 
-	ret = iomap_dio_rw(iocb, to, &gfs2_iomap_ops, NULL, 0);
-	gfs2_glock_dq(gh);
+	if (should_fault_in_pages(ret, to, &prev_count, &window_size)) {
+		size_t leftover;
+
+		gfs2_holder_allow_demote(gh);
+		leftover = fault_in_iov_iter_writeable(to, window_size);
+		gfs2_holder_disallow_demote(gh);
+		if (leftover != window_size) {
+			if (gfs2_holder_queued(gh))
+				goto retry_under_glock;
+			goto retry;
+		}
+	}
+	if (gfs2_holder_queued(gh))
+		gfs2_glock_dq(gh);
 out_uninit:
 	gfs2_holder_uninit(gh);
-	return ret;
+	if (ret < 0)
+		return ret;
+	return written;
 }
 
 static ssize_t gfs2_file_direct_write(struct kiocb *iocb, struct iov_iter *from,
@@ -805,11 +879,21 @@
 	struct file *file = iocb->ki_filp;
 	struct inode *inode = file->f_mapping->host;
 	struct gfs2_inode *ip = GFS2_I(inode);
-	size_t len = iov_iter_count(from);
-	loff_t offset = iocb->ki_pos;
+	size_t prev_count = 0, window_size = 0;
+	size_t read = 0;
 	ssize_t ret;
 
 	/*
+	 * In this function, we disable page faults when we're holding the
+	 * inode glock while doing I/O.  If a page fault occurs, we indicate
+	 * that the inode glock may be dropped, fault in the pages manually,
+	 * and retry.
+	 *
+	 * For writes, iomap_dio_rw only triggers manual page faults, so we
+	 * don't need to disable physical ones.
+	 */
+
+	/*
 	 * Deferred lock, even if its a write, since we do no allocation on
 	 * this path. All we need to change is the atime, and this lock mode
 	 * ensures that other nodes have flushed their buffered read caches
@@ -818,45 +902,78 @@
 	 * VFS does.
 	 */
 	gfs2_holder_init(ip->i_gl, LM_ST_DEFERRED, 0, gh);
+retry:
 	ret = gfs2_glock_nq(gh);
 	if (ret)
 		goto out_uninit;
-
+retry_under_glock:
 	/* Silently fall back to buffered I/O when writing beyond EOF */
-	if (offset + len > i_size_read(&ip->i_inode))
+	if (iocb->ki_pos + iov_iter_count(from) > i_size_read(&ip->i_inode))
 		goto out;
 
-	ret = iomap_dio_rw(iocb, from, &gfs2_iomap_ops, NULL, 0);
+	from->nofault = true;
+	ret = iomap_dio_rw(iocb, from, &gfs2_iomap_ops, NULL,
+			   IOMAP_DIO_PARTIAL, read);
+	from->nofault = false;
+
 	if (ret == -ENOTBLK)
 		ret = 0;
+	if (ret > 0)
+		read = ret;
+
+	if (should_fault_in_pages(ret, from, &prev_count, &window_size)) {
+		size_t leftover;
+
+		gfs2_holder_allow_demote(gh);
+		leftover = fault_in_iov_iter_readable(from, window_size);
+		gfs2_holder_disallow_demote(gh);
+		if (leftover != window_size) {
+			if (gfs2_holder_queued(gh))
+				goto retry_under_glock;
+			goto retry;
+		}
+	}
 out:
-	gfs2_glock_dq(gh);
+	if (gfs2_holder_queued(gh))
+		gfs2_glock_dq(gh);
 out_uninit:
 	gfs2_holder_uninit(gh);
-	return ret;
+	if (ret < 0)
+		return ret;
+	return read;
 }
 
 static ssize_t gfs2_file_read_iter(struct kiocb *iocb, struct iov_iter *to)
 {
 	struct gfs2_inode *ip;
 	struct gfs2_holder gh;
+	size_t prev_count = 0, window_size = 0;
 	size_t written = 0;
 	ssize_t ret;
 
+	/*
+	 * In this function, we disable page faults when we're holding the
+	 * inode glock while doing I/O.  If a page fault occurs, we indicate
+	 * that the inode glock may be dropped, fault in the pages manually,
+	 * and retry.
+	 */
+
 	if (iocb->ki_flags & IOCB_DIRECT) {
 		ret = gfs2_file_direct_read(iocb, to, &gh);
 		if (likely(ret != -ENOTBLK))
 			return ret;
 		iocb->ki_flags &= ~IOCB_DIRECT;
 	}
+	pagefault_disable();
 	iocb->ki_flags |= IOCB_NOIO;
 	ret = generic_file_read_iter(iocb, to);
 	iocb->ki_flags &= ~IOCB_NOIO;
+	pagefault_enable();
 	if (ret >= 0) {
 		if (!iov_iter_count(to))
 			return ret;
 		written = ret;
-	} else {
+	} else if (ret != -EFAULT) {
 		if (ret != -EAGAIN)
 			return ret;
 		if (iocb->ki_flags & IOCB_NOWAIT)
@@ -864,18 +981,116 @@
 	}
 	ip = GFS2_I(iocb->ki_filp->f_mapping->host);
 	gfs2_holder_init(ip->i_gl, LM_ST_SHARED, 0, &gh);
+retry:
 	ret = gfs2_glock_nq(&gh);
 	if (ret)
 		goto out_uninit;
+retry_under_glock:
+	pagefault_disable();
 	ret = generic_file_read_iter(iocb, to);
+	pagefault_enable();
 	if (ret > 0)
 		written += ret;
-	gfs2_glock_dq(&gh);
+
+	if (should_fault_in_pages(ret, to, &prev_count, &window_size)) {
+		size_t leftover;
+
+		gfs2_holder_allow_demote(&gh);
+		leftover = fault_in_iov_iter_writeable(to, window_size);
+		gfs2_holder_disallow_demote(&gh);
+		if (leftover != window_size) {
+			if (gfs2_holder_queued(&gh))
+				goto retry_under_glock;
+			goto retry;
+		}
+	}
+	if (gfs2_holder_queued(&gh))
+		gfs2_glock_dq(&gh);
 out_uninit:
 	gfs2_holder_uninit(&gh);
 	return written ? written : ret;
 }
 
+static ssize_t gfs2_file_buffered_write(struct kiocb *iocb,
+					struct iov_iter *from,
+					struct gfs2_holder *gh)
+{
+	struct file *file = iocb->ki_filp;
+	struct inode *inode = file_inode(file);
+	struct gfs2_inode *ip = GFS2_I(inode);
+	struct gfs2_sbd *sdp = GFS2_SB(inode);
+	struct gfs2_holder *statfs_gh = NULL;
+	size_t prev_count = 0, window_size = 0;
+	size_t orig_count = iov_iter_count(from);
+	size_t read = 0;
+	ssize_t ret;
+
+	/*
+	 * In this function, we disable page faults when we're holding the
+	 * inode glock while doing I/O.  If a page fault occurs, we indicate
+	 * that the inode glock may be dropped, fault in the pages manually,
+	 * and retry.
+	 */
+
+	if (inode == sdp->sd_rindex) {
+		statfs_gh = kmalloc(sizeof(*statfs_gh), GFP_NOFS);
+		if (!statfs_gh)
+			return -ENOMEM;
+	}
+
+	gfs2_holder_init(ip->i_gl, LM_ST_EXCLUSIVE, 0, gh);
+retry:
+	ret = gfs2_glock_nq(gh);
+	if (ret)
+		goto out_uninit;
+retry_under_glock:
+	if (inode == sdp->sd_rindex) {
+		struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
+
+		ret = gfs2_glock_nq_init(m_ip->i_gl, LM_ST_EXCLUSIVE,
+					 GL_NOCACHE, statfs_gh);
+		if (ret)
+			goto out_unlock;
+	}
+
+	current->backing_dev_info = inode_to_bdi(inode);
+	pagefault_disable();
+	ret = iomap_file_buffered_write(iocb, from, &gfs2_iomap_ops);
+	pagefault_enable();
+	current->backing_dev_info = NULL;
+	if (ret > 0) {
+		iocb->ki_pos += ret;
+		read += ret;
+	}
+
+	if (inode == sdp->sd_rindex)
+		gfs2_glock_dq_uninit(statfs_gh);
+
+	from->count = orig_count - read;
+	if (should_fault_in_pages(ret, from, &prev_count, &window_size)) {
+		size_t leftover;
+
+		gfs2_holder_allow_demote(gh);
+		leftover = fault_in_iov_iter_readable(from, window_size);
+		gfs2_holder_disallow_demote(gh);
+		if (leftover != window_size) {
+			from->count = min(from->count, window_size - leftover);
+			if (gfs2_holder_queued(gh))
+				goto retry_under_glock;
+			goto retry;
+		}
+	}
+out_unlock:
+	if (gfs2_holder_queued(gh))
+		gfs2_glock_dq(gh);
+out_uninit:
+	gfs2_holder_uninit(gh);
+	if (statfs_gh)
+		kfree(statfs_gh);
+	from->count = orig_count - read;
+	return read ? read : ret;
+}
+
 /**
  * gfs2_file_write_iter - Perform a write to a file
  * @iocb: The io context
@@ -927,9 +1142,7 @@
 			goto out_unlock;
 
 		iocb->ki_flags |= IOCB_DSYNC;
-		current->backing_dev_info = inode_to_bdi(inode);
-		buffered = iomap_file_buffered_write(iocb, from, &gfs2_iomap_ops);
-		current->backing_dev_info = NULL;
+		buffered = gfs2_file_buffered_write(iocb, from, &gh);
 		if (unlikely(buffered <= 0)) {
 			if (!ret)
 				ret = buffered;
@@ -943,7 +1156,6 @@
 		 * the direct I/O range as we don't know if the buffered pages
 		 * made it to disk.
 		 */
-		iocb->ki_pos += buffered;
 		ret2 = generic_write_sync(iocb, buffered);
 		invalidate_mapping_pages(mapping,
 				(iocb->ki_pos - buffered) >> PAGE_SHIFT,
@@ -951,13 +1163,9 @@
 		if (!ret || ret2 > 0)
 			ret += ret2;
 	} else {
-		current->backing_dev_info = inode_to_bdi(inode);
-		ret = iomap_file_buffered_write(iocb, from, &gfs2_iomap_ops);
-		current->backing_dev_info = NULL;
-		if (likely(ret > 0)) {
-			iocb->ki_pos += ret;
+		ret = gfs2_file_buffered_write(iocb, from, &gh);
+		if (likely(ret > 0))
 			ret = generic_write_sync(iocb, ret);
-		}
 	}
 
 out_unlock:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/glock.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/glock.c
@@ -58,6 +58,7 @@
 typedef void (*glock_examiner) (struct gfs2_glock * gl);
 
 static void do_xmote(struct gfs2_glock *gl, struct gfs2_holder *gh, unsigned int target);
+static void __gfs2_glock_dq(struct gfs2_holder *gh);
 
 static struct dentry *gfs2_root;
 static struct workqueue_struct *glock_workqueue;
@@ -159,17 +160,44 @@
 	return true;
 }
 
-void gfs2_glock_free(struct gfs2_glock *gl)
+static void __gfs2_glock_free(struct gfs2_glock *gl)
 {
-	struct gfs2_sbd *sdp = gl->gl_name.ln_sbd;
-
 	gfs2_glock_assert_withdraw(gl, atomic_read(&gl->gl_revokes) == 0);
 	rhashtable_remove_fast(&gl_hash_table, &gl->gl_node, ht_parms);
 	smp_mb();
 	wake_up_glock(gl);
 	call_rcu(&gl->gl_rcu, gfs2_glock_dealloc);
+}
+
+void gfs2_glock_free(struct gfs2_glock *gl) {
+	struct gfs2_sbd *sdp = gl->gl_name.ln_sbd;
+
+	__gfs2_glock_free(gl);
+	if (atomic_dec_and_test(&sdp->sd_glock_disposal))
+		wake_up(&sdp->sd_kill_wait);
+}
+
+void gfs2_glock_free_later(struct gfs2_glock *gl) {
+	struct gfs2_sbd *sdp = gl->gl_name.ln_sbd;
+
+	spin_lock(&lru_lock);
+	list_add(&gl->gl_lru, &sdp->sd_dead_glocks);
+	spin_unlock(&lru_lock);
 	if (atomic_dec_and_test(&sdp->sd_glock_disposal))
-		wake_up(&sdp->sd_glock_wait);
+		wake_up(&sdp->sd_kill_wait);
+}
+
+static void gfs2_free_dead_glocks(struct gfs2_sbd *sdp)
+{
+	struct list_head *list = &sdp->sd_dead_glocks;
+
+	while(!list_empty(list)) {
+		struct gfs2_glock *gl;
+
+		gl = list_first_entry(list, struct gfs2_glock, gl_lru);
+		list_del_init(&gl->gl_lru);
+		__gfs2_glock_free(gl);
+	}
 }
 
 /**
@@ -197,6 +225,12 @@
 
 	if (gl->gl_state == LM_ST_UNLOCKED)
 		return 0;
+	/*
+	 * Note that demote_ok is used for the lru process of disposing of
+	 * glocks. For this purpose, we don't care if the glock's holders
+	 * have the HIF_MAY_DEMOTE flag set or not. If someone is using
+	 * them, don't demote.
+	 */
 	if (!list_empty(&gl->gl_holders))
 		return 0;
 	if (glops->go_demote_ok)
@@ -301,46 +335,59 @@
 }
 
 /**
- * may_grant - check if its ok to grant a new lock
+ * may_grant - check if it's ok to grant a new lock
  * @gl: The glock
+ * @current_gh: One of the current holders of @gl
  * @gh: The lock request which we wish to grant
  *
- * Returns: true if its ok to grant the lock
- */
+ * With our current compatibility rules, if a glock has one or more active
+ * holders (HIF_HOLDER flag set), any of those holders can be passed in as
+ * @current_gh; they are all the same as far as compatibility with the new @gh
+ * goes.
+ *
+ * Returns true if it's ok to grant the lock.
+ */
+
+static inline bool may_grant(struct gfs2_glock *gl,
+			     struct gfs2_holder *current_gh,
+			     struct gfs2_holder *gh)
+{
+	if (current_gh) {
+		GLOCK_BUG_ON(gl, !test_bit(HIF_HOLDER, &current_gh->gh_iflags));
+
+		switch(current_gh->gh_state) {
+		case LM_ST_EXCLUSIVE:
+			/*
+			 * Here we make a special exception to grant holders
+			 * who agree to share the EX lock with other holders
+			 * who also have the bit set. If the original holder
+			 * has the LM_FLAG_NODE_SCOPE bit set, we grant more
+			 * holders with the bit set.
+			 */
+			return gh->gh_state == LM_ST_EXCLUSIVE &&
+			       (current_gh->gh_flags & LM_FLAG_NODE_SCOPE) &&
+			       (gh->gh_flags & LM_FLAG_NODE_SCOPE);
 
-static inline int may_grant(const struct gfs2_glock *gl, const struct gfs2_holder *gh)
-{
-	const struct gfs2_holder *gh_head = list_first_entry(&gl->gl_holders, const struct gfs2_holder, gh_list);
+		case LM_ST_SHARED:
+		case LM_ST_DEFERRED:
+			return gh->gh_state == current_gh->gh_state;
 
-	if (gh != gh_head) {
-		/**
-		 * Here we make a special exception to grant holders who agree
-		 * to share the EX lock with other holders who also have the
-		 * bit set. If the original holder has the LM_FLAG_NODE_SCOPE bit
-		 * is set, we grant more holders with the bit set.
-		 */
-		if (gh_head->gh_state == LM_ST_EXCLUSIVE &&
-		    (gh_head->gh_flags & LM_FLAG_NODE_SCOPE) &&
-		    gh->gh_state == LM_ST_EXCLUSIVE &&
-		    (gh->gh_flags & LM_FLAG_NODE_SCOPE))
-			return 1;
-		if ((gh->gh_state == LM_ST_EXCLUSIVE ||
-		     gh_head->gh_state == LM_ST_EXCLUSIVE))
-			return 0;
+		default:
+			return false;
+		}
 	}
+
 	if (gl->gl_state == gh->gh_state)
-		return 1;
+		return true;
 	if (gh->gh_flags & GL_EXACT)
-		return 0;
+		return false;
 	if (gl->gl_state == LM_ST_EXCLUSIVE) {
-		if (gh->gh_state == LM_ST_SHARED && gh_head->gh_state == LM_ST_SHARED)
-			return 1;
-		if (gh->gh_state == LM_ST_DEFERRED && gh_head->gh_state == LM_ST_DEFERRED)
-			return 1;
+		return gh->gh_state == LM_ST_SHARED ||
+		       gh->gh_state == LM_ST_DEFERRED;
 	}
-	if (gl->gl_state != LM_ST_UNLOCKED && (gh->gh_flags & LM_FLAG_ANY))
-		return 1;
-	return 0;
+	if (gh->gh_flags & LM_FLAG_ANY)
+		return gl->gl_state != LM_ST_UNLOCKED;
+	return false;
 }
 
 static void gfs2_holder_wake(struct gfs2_holder *gh)
@@ -366,7 +413,7 @@
 	struct gfs2_holder *gh, *tmp;
 
 	list_for_each_entry_safe(gh, tmp, &gl->gl_holders, gh_list) {
-		if (test_bit(HIF_HOLDER, &gh->gh_iflags))
+		if (!test_bit(HIF_WAIT, &gh->gh_iflags))
 			continue;
 		if (ret & LM_OUT_ERROR)
 			gh->gh_error = -EIO;
@@ -381,6 +428,78 @@
 }
 
 /**
+ * demote_incompat_holders - demote incompatible demoteable holders
+ * @gl: the glock we want to promote
+ * @new_gh: the new holder to be promoted
+ */
+static void demote_incompat_holders(struct gfs2_glock *gl,
+				    struct gfs2_holder *new_gh)
+{
+	struct gfs2_holder *gh;
+
+	/*
+	 * Demote incompatible holders before we make ourselves eligible.
+	 * (This holder may or may not allow auto-demoting, but we don't want
+	 * to demote the new holder before it's even granted.)
+	 */
+	list_for_each_entry(gh, &gl->gl_holders, gh_list) {
+		/*
+		 * Since holders are at the front of the list, we stop when we
+		 * find the first non-holder.
+		 */
+		if (!test_bit(HIF_HOLDER, &gh->gh_iflags))
+			return;
+		if (test_bit(HIF_MAY_DEMOTE, &gh->gh_iflags) &&
+		    !may_grant(gl, new_gh, gh)) {
+			/*
+			 * We should not recurse into do_promote because
+			 * __gfs2_glock_dq only calls handle_callback,
+			 * gfs2_glock_add_to_lru and __gfs2_glock_queue_work.
+			 */
+			__gfs2_glock_dq(gh);
+		}
+	}
+}
+
+/**
+ * find_first_holder - find the first "holder" gh
+ * @gl: the glock
+ */
+
+static inline struct gfs2_holder *find_first_holder(const struct gfs2_glock *gl)
+{
+	struct gfs2_holder *gh;
+
+	if (!list_empty(&gl->gl_holders)) {
+		gh = list_first_entry(&gl->gl_holders, struct gfs2_holder,
+				      gh_list);
+		if (test_bit(HIF_HOLDER, &gh->gh_iflags))
+			return gh;
+	}
+	return NULL;
+}
+
+/**
+ * find_first_strong_holder - find the first non-demoteable holder
+ * @gl: the glock
+ *
+ * Find the first holder that doesn't have the HIF_MAY_DEMOTE flag set.
+ */
+static inline struct gfs2_holder *
+find_first_strong_holder(struct gfs2_glock *gl)
+{
+	struct gfs2_holder *gh;
+
+	list_for_each_entry(gh, &gl->gl_holders, gh_list) {
+		if (!test_bit(HIF_HOLDER, &gh->gh_iflags))
+			return NULL;
+		if (!test_bit(HIF_MAY_DEMOTE, &gh->gh_iflags))
+			return gh;
+	}
+	return NULL;
+}
+
+/**
  * do_promote - promote as many requests as possible on the current queue
  * @gl: The glock
  * 
@@ -393,14 +512,21 @@
 __acquires(&gl->gl_lockref.lock)
 {
 	const struct gfs2_glock_operations *glops = gl->gl_ops;
-	struct gfs2_holder *gh, *tmp;
+	struct gfs2_holder *gh, *tmp, *first_gh;
+	bool incompat_holders_demoted = false;
 	int ret;
 
 restart:
+	first_gh = find_first_strong_holder(gl);
 	list_for_each_entry_safe(gh, tmp, &gl->gl_holders, gh_list) {
-		if (test_bit(HIF_HOLDER, &gh->gh_iflags))
+		if (!test_bit(HIF_WAIT, &gh->gh_iflags))
 			continue;
-		if (may_grant(gl, gh)) {
+		if (may_grant(gl, first_gh, gh)) {
+			if (!incompat_holders_demoted) {
+				demote_incompat_holders(gl, first_gh);
+				incompat_holders_demoted = true;
+				first_gh = gh;
+			}
 			if (gh->gh_list.prev == &gl->gl_holders &&
 			    glops->go_lock) {
 				spin_unlock(&gl->gl_lockref.lock);
@@ -426,6 +552,11 @@
 			gfs2_holder_wake(gh);
 			continue;
 		}
+		/*
+		 * If we get here, it means we may not grant this holder for
+		 * some reason. If this holder is the head of the list, it
+		 * means we have a blocked holder at the head, so return 1.
+		 */
 		if (gh->gh_list.prev == &gl->gl_holders)
 			return 1;
 		do_error(gl, 0);
@@ -703,11 +834,13 @@
 	}
 
 	if (sdp->sd_lockstruct.ls_ops->lm_lock)	{
+		struct lm_lockstruct *ls = &sdp->sd_lockstruct;
+
 		/* lock_dlm */
 		ret = sdp->sd_lockstruct.ls_ops->lm_lock(gl, target, lck_flags);
 		if (ret == -EINVAL && gl->gl_target == LM_ST_UNLOCKED &&
 		    target == LM_ST_UNLOCKED &&
-		    test_bit(SDF_SKIP_DLM_UNLOCK, &sdp->sd_flags)) {
+		    test_bit(DFL_UNMOUNT, &ls->ls_recover_flags)) {
 			finish_xmote(gl, target);
 			gfs2_glock_queue_work(gl, 0);
 		} else if (ret) {
@@ -723,23 +856,6 @@
 }
 
 /**
- * find_first_holder - find the first "holder" gh
- * @gl: the glock
- */
-
-static inline struct gfs2_holder *find_first_holder(const struct gfs2_glock *gl)
-{
-	struct gfs2_holder *gh;
-
-	if (!list_empty(&gl->gl_holders)) {
-		gh = list_first_entry(&gl->gl_holders, struct gfs2_holder, gh_list);
-		if (test_bit(HIF_HOLDER, &gh->gh_iflags))
-			return gh;
-	}
-	return NULL;
-}
-
-/**
  * run_queue - do all outstanding tasks related to a glock
  * @gl: The glock in question
  * @nonblock: True if we must not block in run_queue
@@ -1104,7 +1220,7 @@
 	kfree(gl->gl_lksb.sb_lvbptr);
 	kmem_cache_free(cachep, gl);
 	if (atomic_dec_and_test(&sdp->sd_glock_disposal))
-		wake_up(&sdp->sd_glock_wait);
+		wake_up(&sdp->sd_kill_wait);
 
 out:
 	return ret;
@@ -1354,15 +1470,20 @@
 		GLOCK_BUG_ON(gl, true);
 
 	if (gh->gh_flags & (LM_FLAG_TRY | LM_FLAG_TRY_1CB)) {
-		if (test_bit(GLF_LOCK, &gl->gl_flags))
-			try_futile = !may_grant(gl, gh);
+		if (test_bit(GLF_LOCK, &gl->gl_flags)) {
+			struct gfs2_holder *first_gh;
+
+			first_gh = find_first_strong_holder(gl);
+			try_futile = !may_grant(gl, first_gh, gh);
+		}
 		if (test_bit(GLF_INVALIDATE_IN_PROGRESS, &gl->gl_flags))
 			goto fail;
 	}
 
 	list_for_each_entry(gh2, &gl->gl_holders, gh_list) {
 		if (unlikely(gh2->gh_owner_pid == gh->gh_owner_pid &&
-		    (gh->gh_gl->gl_ops->go_type != LM_TYPE_FLOCK)))
+		    (gh->gh_gl->gl_ops->go_type != LM_TYPE_FLOCK) &&
+		    !test_bit(HIF_MAY_DEMOTE, &gh2->gh_iflags)))
 			goto trap_recursive;
 		if (try_futile &&
 		    !(gh2->gh_flags & (LM_FLAG_TRY | LM_FLAG_TRY_1CB))) {
@@ -1458,51 +1579,83 @@
 	return test_bit(HIF_WAIT, &gh->gh_iflags) ? 0 : 1;
 }
 
-/**
- * gfs2_glock_dq - dequeue a struct gfs2_holder from a glock (release a glock)
- * @gh: the glock holder
- *
- */
+static inline bool needs_demote(struct gfs2_glock *gl)
+{
+	return (test_bit(GLF_DEMOTE, &gl->gl_flags) ||
+		test_bit(GLF_PENDING_DEMOTE, &gl->gl_flags));
+}
 
-void gfs2_glock_dq(struct gfs2_holder *gh)
+static void __gfs2_glock_dq(struct gfs2_holder *gh)
 {
 	struct gfs2_glock *gl = gh->gh_gl;
 	struct gfs2_sbd *sdp = gl->gl_name.ln_sbd;
 	unsigned delay = 0;
 	int fast_path = 0;
 
-	spin_lock(&gl->gl_lockref.lock);
 	/*
-	 * If we're in the process of file system withdraw, we cannot just
-	 * dequeue any glocks until our journal is recovered, lest we
-	 * introduce file system corruption. We need two exceptions to this
-	 * rule: We need to allow unlocking of nondisk glocks and the glock
-	 * for our own journal that needs recovery.
+	 * This while loop is similar to function demote_incompat_holders:
+	 * If the glock is due to be demoted (which may be from another node
+	 * or even if this holder is GL_NOCACHE), the weak holders are
+	 * demoted as well, allowing the glock to be demoted.
 	 */
-	if (test_bit(SDF_WITHDRAW_RECOVERY, &sdp->sd_flags) &&
-	    glock_blocked_by_withdraw(gl) &&
-	    gh->gh_gl != sdp->sd_jinode_gl) {
-		sdp->sd_glock_dqs_held++;
-		spin_unlock(&gl->gl_lockref.lock);
-		might_sleep();
-		wait_on_bit(&sdp->sd_flags, SDF_WITHDRAW_RECOVERY,
-			    TASK_UNINTERRUPTIBLE);
-		spin_lock(&gl->gl_lockref.lock);
-	}
-	if (gh->gh_flags & GL_NOCACHE)
-		handle_callback(gl, LM_ST_UNLOCKED, 0, false);
+	while (gh) {
+		/*
+		 * If we're in the process of file system withdraw, we cannot
+		 * just dequeue any glocks until our journal is recovered, lest
+		 * we introduce file system corruption. We need two exceptions
+		 * to this rule: We need to allow unlocking of nondisk glocks
+		 * and the glock for our own journal that needs recovery.
+		 */
+		if (test_bit(SDF_WITHDRAW_RECOVERY, &sdp->sd_flags) &&
+		    glock_blocked_by_withdraw(gl) &&
+		    gh->gh_gl != sdp->sd_jinode_gl) {
+			sdp->sd_glock_dqs_held++;
+			spin_unlock(&gl->gl_lockref.lock);
+			might_sleep();
+			wait_on_bit(&sdp->sd_flags, SDF_WITHDRAW_RECOVERY,
+				    TASK_UNINTERRUPTIBLE);
+			spin_lock(&gl->gl_lockref.lock);
+		}
 
-	list_del_init(&gh->gh_list);
-	clear_bit(HIF_HOLDER, &gh->gh_iflags);
-	if (list_empty(&gl->gl_holders) &&
-	    !test_bit(GLF_PENDING_DEMOTE, &gl->gl_flags) &&
-	    !test_bit(GLF_DEMOTE, &gl->gl_flags))
-		fast_path = 1;
+		/*
+		 * This holder should not be cached, so mark it for demote.
+		 * Note: this should be done before the check for needs_demote
+		 * below.
+		 */
+		if (gh->gh_flags & GL_NOCACHE)
+			handle_callback(gl, LM_ST_UNLOCKED, 0, false);
+
+		list_del_init(&gh->gh_list);
+		clear_bit(HIF_HOLDER, &gh->gh_iflags);
+		trace_gfs2_glock_queue(gh, 0);
+
+		/*
+		 * If there hasn't been a demote request we are done.
+		 * (Let the remaining holders, if any, keep holding it.)
+		 */
+		if (!needs_demote(gl)) {
+			if (list_empty(&gl->gl_holders))
+				fast_path = 1;
+			break;
+		}
+		/*
+		 * If we have another strong holder (we cannot auto-demote)
+		 * we are done. It keeps holding it until it is done.
+		 */
+		if (find_first_strong_holder(gl))
+			break;
+
+		/*
+		 * If we have a weak holder at the head of the list, it
+		 * (and all others like it) must be auto-demoted. If there
+		 * are no more weak holders, we exit the while loop.
+		 */
+		gh = find_first_holder(gl);
+	}
 
 	if (!test_bit(GLF_LFLUSH, &gl->gl_flags) && demote_ok(gl))
 		gfs2_glock_add_to_lru(gl);
 
-	trace_gfs2_glock_queue(gh, 0);
 	if (unlikely(!fast_path)) {
 		gl->gl_lockref.count++;
 		if (test_bit(GLF_PENDING_DEMOTE, &gl->gl_flags) &&
@@ -1511,6 +1664,19 @@
 			delay = gl->gl_hold_time;
 		__gfs2_glock_queue_work(gl, delay);
 	}
+}
+
+/**
+ * gfs2_glock_dq - dequeue a struct gfs2_holder from a glock (release a glock)
+ * @gh: the glock holder
+ *
+ */
+void gfs2_glock_dq(struct gfs2_holder *gh)
+{
+	struct gfs2_glock *gl = gh->gh_gl;
+
+	spin_lock(&gl->gl_lockref.lock);
+	__gfs2_glock_dq(gh);
 	spin_unlock(&gl->gl_lockref.lock);
 }
 
@@ -1673,6 +1839,7 @@
 
 void gfs2_glock_cb(struct gfs2_glock *gl, unsigned int state)
 {
+	struct gfs2_holder mock_gh = { .gh_gl = gl, .gh_state = state, };
 	unsigned long delay = 0;
 	unsigned long holdtime;
 	unsigned long now = jiffies;
@@ -1687,6 +1854,28 @@
 		if (test_bit(GLF_REPLY_PENDING, &gl->gl_flags))
 			delay = gl->gl_hold_time;
 	}
+	/*
+	 * Note 1: We cannot call demote_incompat_holders from handle_callback
+	 * or gfs2_set_demote due to recursion problems like: gfs2_glock_dq ->
+	 * handle_callback -> demote_incompat_holders -> gfs2_glock_dq
+	 * Plus, we only want to demote the holders if the request comes from
+	 * a remote cluster node because local holder conflicts are resolved
+	 * elsewhere.
+	 *
+	 * Note 2: if a remote node wants this glock in EX mode, lock_dlm will
+	 * request that we set our state to UNLOCKED. Here we mock up a holder
+	 * to make it look like someone wants the lock EX locally. Any SH
+	 * and DF requests should be able to share the lock without demoting.
+	 *
+	 * Note 3: We only want to demote the demoteable holders when there
+	 * are no more strong holders. The demoteable holders might as well
+	 * keep the glock until the last strong holder is done with it.
+	 */
+	if (!find_first_strong_holder(gl)) {
+		if (state == LM_ST_UNLOCKED)
+			mock_gh.gh_state = LM_ST_EXCLUSIVE;
+		demote_incompat_holders(gl, &mock_gh);
+	}
 	handle_callback(gl, state, delay, true);
 	__gfs2_glock_queue_work(gl, delay);
 	spin_unlock(&gl->gl_lockref.lock);
@@ -1893,10 +2082,10 @@
 	do {
 		rhashtable_walk_start(&iter);
 
-		while ((gl = rhashtable_walk_next(&iter)) && !IS_ERR(gl))
-			if (gl->gl_name.ln_sbd == sdp &&
-			    lockref_get_not_dead(&gl->gl_lockref))
+		while ((gl = rhashtable_walk_next(&iter)) && !IS_ERR(gl)) {
+			if (gl->gl_name.ln_sbd == sdp)
 				examiner(gl);
+		}
 
 		rhashtable_walk_stop(&iter);
 	} while (cond_resched(), gl == ERR_PTR(-EAGAIN));
@@ -1919,7 +2108,7 @@
 
 void gfs2_cancel_delete_work(struct gfs2_glock *gl)
 {
-	if (cancel_delayed_work_sync(&gl->gl_delete)) {
+	if (cancel_delayed_work(&gl->gl_delete)) {
 		clear_bit(GLF_PENDING_DELETE, &gl->gl_flags);
 		gfs2_glock_put(gl);
 	}
@@ -1938,7 +2127,6 @@
 					   &gl->gl_delete, 0);
 		}
 	}
-	gfs2_glock_queue_work(gl, 0);
 }
 
 void gfs2_flush_delete_work(struct gfs2_sbd *sdp)
@@ -1955,10 +2143,10 @@
 
 static void thaw_glock(struct gfs2_glock *gl)
 {
-	if (!test_and_clear_bit(GLF_FROZEN, &gl->gl_flags)) {
-		gfs2_glock_put(gl);
+	if (!test_and_clear_bit(GLF_FROZEN, &gl->gl_flags))
+		return;
+	if (!lockref_get_not_dead(&gl->gl_lockref))
 		return;
-	}
 	set_bit(GLF_REPLY_PENDING, &gl->gl_flags);
 	gfs2_glock_queue_work(gl, 0);
 }
@@ -1974,9 +2162,12 @@
 	gfs2_glock_remove_from_lru(gl);
 
 	spin_lock(&gl->gl_lockref.lock);
-	if (gl->gl_state != LM_ST_UNLOCKED)
-		handle_callback(gl, LM_ST_UNLOCKED, 0, false);
-	__gfs2_glock_queue_work(gl, 0);
+	if (!__lockref_is_dead(&gl->gl_lockref)) {
+		gl->gl_lockref.count++;
+		if (gl->gl_state != LM_ST_UNLOCKED)
+			handle_callback(gl, LM_ST_UNLOCKED, 0, false);
+		__gfs2_glock_queue_work(gl, 0);
+	}
 	spin_unlock(&gl->gl_lockref.lock);
 }
 
@@ -2016,9 +2207,11 @@
 	flush_workqueue(glock_workqueue);
 	glock_hash_walk(clear_glock, sdp);
 	flush_workqueue(glock_workqueue);
-	wait_event_timeout(sdp->sd_glock_wait,
+	wait_event_timeout(sdp->sd_kill_wait,
 			   atomic_read(&sdp->sd_glock_disposal) == 0,
 			   HZ * 600);
+	gfs2_lm_unmount(sdp);
+	gfs2_free_dead_glocks(sdp);
 	glock_hash_walk(dump_glock_func, sdp);
 }
 
@@ -2076,6 +2269,8 @@
 		*p++ = 'H';
 	if (test_bit(HIF_WAIT, &iflags))
 		*p++ = 'W';
+	if (test_bit(HIF_MAY_DEMOTE, &iflags))
+		*p++ = 'D';
 	*p = 0;
 	return buf;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/glock.h
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/glock.h
@@ -150,6 +150,8 @@
 	list_for_each_entry(gh, &gl->gl_holders, gh_list) {
 		if (!test_bit(HIF_HOLDER, &gh->gh_iflags))
 			break;
+		if (test_bit(HIF_MAY_DEMOTE, &gh->gh_iflags))
+			continue;
 		if (gh->gh_owner_pid == pid)
 			goto out;
 	}
@@ -259,6 +261,7 @@
 extern void gfs2_glock_thaw(struct gfs2_sbd *sdp);
 extern void gfs2_glock_add_to_lru(struct gfs2_glock *gl);
 extern void gfs2_glock_free(struct gfs2_glock *gl);
+void gfs2_glock_free_later(struct gfs2_glock *gl);
 
 extern int __init gfs2_glock_init(void);
 extern void gfs2_glock_exit(void);
@@ -325,6 +328,24 @@
 	spin_unlock(&gl->gl_lockref.lock);
 }
 
+static inline void gfs2_holder_allow_demote(struct gfs2_holder *gh)
+{
+	struct gfs2_glock *gl = gh->gh_gl;
+
+	spin_lock(&gl->gl_lockref.lock);
+	set_bit(HIF_MAY_DEMOTE, &gh->gh_iflags);
+	spin_unlock(&gl->gl_lockref.lock);
+}
+
+static inline void gfs2_holder_disallow_demote(struct gfs2_holder *gh)
+{
+	struct gfs2_glock *gl = gh->gh_gl;
+
+	spin_lock(&gl->gl_lockref.lock);
+	clear_bit(HIF_MAY_DEMOTE, &gh->gh_iflags);
+	spin_unlock(&gl->gl_lockref.lock);
+}
+
 extern void gfs2_inode_remember_delete(struct gfs2_glock *gl, u64 generation);
 extern bool gfs2_inode_already_deleted(struct gfs2_glock *gl, u64 generation);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/glops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/glops.c
@@ -82,6 +82,9 @@
 	GLOCK_BUG_ON(gl, !fsync && atomic_read(&gl->gl_ail_count));
 	spin_unlock(&sdp->sd_ail_lock);
 	gfs2_log_unlock(sdp);
+
+	if (gfs2_withdrawing(sdp))
+		gfs2_withdraw(sdp);
 }
 
 
@@ -394,42 +397,44 @@
 
 static int gfs2_dinode_in(struct gfs2_inode *ip, const void *buf)
 {
+	struct gfs2_sbd *sdp = GFS2_SB(&ip->i_inode);
 	const struct gfs2_dinode *str = buf;
 	struct timespec64 atime;
 	u16 height, depth;
 	umode_t mode = be32_to_cpu(str->di_mode);
-	bool is_new = ip->i_inode.i_state & I_NEW;
+	struct inode *inode = &ip->i_inode;
+	bool is_new = inode->i_state & I_NEW;
 
 	if (unlikely(ip->i_no_addr != be64_to_cpu(str->di_num.no_addr)))
 		goto corrupt;
-	if (unlikely(!is_new && inode_wrong_type(&ip->i_inode, mode)))
+	if (unlikely(!is_new && inode_wrong_type(inode, mode)))
 		goto corrupt;
 	ip->i_no_formal_ino = be64_to_cpu(str->di_num.no_formal_ino);
-	ip->i_inode.i_mode = mode;
+	inode->i_mode = mode;
 	if (is_new) {
-		ip->i_inode.i_rdev = 0;
+		inode->i_rdev = 0;
 		switch (mode & S_IFMT) {
 		case S_IFBLK:
 		case S_IFCHR:
-			ip->i_inode.i_rdev = MKDEV(be32_to_cpu(str->di_major),
-						   be32_to_cpu(str->di_minor));
+			inode->i_rdev = MKDEV(be32_to_cpu(str->di_major),
+					      be32_to_cpu(str->di_minor));
 			break;
 		}
 	}
 
-	i_uid_write(&ip->i_inode, be32_to_cpu(str->di_uid));
-	i_gid_write(&ip->i_inode, be32_to_cpu(str->di_gid));
-	set_nlink(&ip->i_inode, be32_to_cpu(str->di_nlink));
-	i_size_write(&ip->i_inode, be64_to_cpu(str->di_size));
-	gfs2_set_inode_blocks(&ip->i_inode, be64_to_cpu(str->di_blocks));
+	i_uid_write(inode, be32_to_cpu(str->di_uid));
+	i_gid_write(inode, be32_to_cpu(str->di_gid));
+	set_nlink(inode, be32_to_cpu(str->di_nlink));
+	i_size_write(inode, be64_to_cpu(str->di_size));
+	gfs2_set_inode_blocks(inode, be64_to_cpu(str->di_blocks));
 	atime.tv_sec = be64_to_cpu(str->di_atime);
 	atime.tv_nsec = be32_to_cpu(str->di_atime_nsec);
-	if (timespec64_compare(&ip->i_inode.i_atime, &atime) < 0)
-		ip->i_inode.i_atime = atime;
-	ip->i_inode.i_mtime.tv_sec = be64_to_cpu(str->di_mtime);
-	ip->i_inode.i_mtime.tv_nsec = be32_to_cpu(str->di_mtime_nsec);
-	ip->i_inode.i_ctime.tv_sec = be64_to_cpu(str->di_ctime);
-	ip->i_inode.i_ctime.tv_nsec = be32_to_cpu(str->di_ctime_nsec);
+	if (timespec64_compare(&inode->i_atime, &atime) < 0)
+		inode->i_atime = atime;
+	inode->i_mtime.tv_sec = be64_to_cpu(str->di_mtime);
+	inode->i_mtime.tv_nsec = be32_to_cpu(str->di_mtime_nsec);
+	inode->i_ctime.tv_sec = be64_to_cpu(str->di_ctime);
+	inode->i_ctime.tv_nsec = be32_to_cpu(str->di_ctime_nsec);
 
 	ip->i_goal = be64_to_cpu(str->di_goal_meta);
 	ip->i_generation = be64_to_cpu(str->di_generation);
@@ -437,9 +442,9 @@
 	ip->i_diskflags = be32_to_cpu(str->di_flags);
 	ip->i_eattr = be64_to_cpu(str->di_eattr);
 	/* i_diskflags and i_eattr must be set before gfs2_set_inode_flags() */
-	gfs2_set_inode_flags(&ip->i_inode);
+	gfs2_set_inode_flags(inode);
 	height = be16_to_cpu(str->di_height);
-	if (unlikely(height > GFS2_MAX_META_HEIGHT))
+	if (unlikely(height > sdp->sd_max_height))
 		goto corrupt;
 	ip->i_height = (u8)height;
 
@@ -449,8 +454,11 @@
 	ip->i_depth = (u8)depth;
 	ip->i_entries = be32_to_cpu(str->di_entries);
 
-	if (S_ISREG(ip->i_inode.i_mode))
-		gfs2_set_aops(&ip->i_inode);
+	if (gfs2_is_stuffed(ip) && inode->i_size > gfs2_max_stuffed_size(ip))
+		goto corrupt;
+
+	if (S_ISREG(inode->i_mode))
+		gfs2_set_aops(inode);
 
 	return 0;
 corrupt:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/incore.h
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/incore.h
@@ -252,6 +252,7 @@
 
 enum {
 	/* States */
+	HIF_MAY_DEMOTE		= 1,
 	HIF_HOLDER		= 6,  /* Set for gh that "holds" the glock */
 	HIF_WAIT		= 10,
 };
@@ -386,9 +387,8 @@
 	u64 i_generation;
 	u64 i_eattr;
 	unsigned long i_flags;		/* GIF_... */
-	struct gfs2_glock *i_gl; /* Move into i_gh? */
+	struct gfs2_glock *i_gl;
 	struct gfs2_holder i_iopen_gh;
-	struct gfs2_holder i_gh; /* for prepare/commit_write only */
 	struct gfs2_qadata *i_qadata; /* quota allocation data */
 	struct gfs2_holder i_rgd_gh;
 	struct gfs2_blkreserv i_res; /* rgrp multi-block reservation */
@@ -719,7 +719,7 @@
 	struct gfs2_glock *sd_rename_gl;
 	struct gfs2_glock *sd_freeze_gl;
 	struct work_struct sd_freeze_work;
-	wait_queue_head_t sd_glock_wait;
+	wait_queue_head_t sd_kill_wait;
 	wait_queue_head_t sd_async_glock_wait;
 	atomic_t sd_glock_disposal;
 	struct completion sd_locking_init;
@@ -839,6 +839,7 @@
 	struct gfs2_holder sd_freeze_gh;
 	atomic_t sd_freeze_state;
 	struct mutex sd_freeze_mutex;
+	struct list_head sd_dead_glocks;
 
 	char sd_fsname[GFS2_FSNAME_LEN + 3 * sizeof(int) + 2];
 	char sd_table_name[GFS2_FSNAME_LEN];
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/inode.c
@@ -811,7 +811,7 @@
 		if (free_vfs_inode) /* else evict will do the put for us */
 			gfs2_glock_put(ip->i_gl);
 	}
-	gfs2_rs_delete(ip, NULL);
+	gfs2_rs_deltree(&ip->i_res);
 	gfs2_qa_put(ip);
 fail_free_acls:
 	posix_acl_release(default_acl);
@@ -1848,16 +1848,24 @@
 int gfs2_permission(struct user_namespace *mnt_userns, struct inode *inode,
 		    int mask)
 {
+	int may_not_block = mask & MAY_NOT_BLOCK;
 	struct gfs2_inode *ip;
 	struct gfs2_holder i_gh;
+	struct gfs2_glock *gl;
 	int error;
 
 	gfs2_holder_mark_uninitialized(&i_gh);
 	ip = GFS2_I(inode);
-	if (gfs2_glock_is_locked_by_me(ip->i_gl) == NULL) {
-		if (mask & MAY_NOT_BLOCK)
+	gl = rcu_dereference_check(ip->i_gl, !may_not_block);
+	if (unlikely(!gl)) {
+		/* inode is getting torn down, must be RCU mode */
+		WARN_ON_ONCE(!may_not_block);
+		return -ECHILD;
+        }
+	if (gfs2_glock_is_locked_by_me(gl) == NULL) {
+		if (may_not_block)
 			return -ECHILD;
-		error = gfs2_glock_nq_init(ip->i_gl, LM_ST_SHARED, LM_FLAG_ANY, &i_gh);
+		error = gfs2_glock_nq_init(gl, LM_ST_SHARED, LM_FLAG_ANY, &i_gh);
 		if (error)
 			return error;
 	}
@@ -1902,7 +1910,7 @@
 	kuid_t ouid, nuid;
 	kgid_t ogid, ngid;
 	int error;
-	struct gfs2_alloc_parms ap;
+	struct gfs2_alloc_parms ap = {};
 
 	ouid = inode->i_uid;
 	ogid = inode->i_gid;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/lock_dlm.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/lock_dlm.c
@@ -121,6 +121,11 @@
 	struct gfs2_glock *gl = arg;
 	unsigned ret = gl->gl_state;
 
+	/* If the glock is dead, we only react to a dlm_unlock() reply. */
+	if (__lockref_is_dead(&gl->gl_lockref) &&
+	    gl->gl_lksb.sb_status != -DLM_EUNLOCK)
+		return;
+
 	gfs2_update_reply_times(gl);
 	BUG_ON(gl->gl_lksb.sb_flags & DLM_SBF_DEMOTED);
 
@@ -171,6 +176,9 @@
 {
 	struct gfs2_glock *gl = arg;
 
+	if (__lockref_is_dead(&gl->gl_lockref))
+		return;
+
 	switch (mode) {
 	case DLM_LOCK_EX:
 		gfs2_glock_cb(gl, LM_ST_UNLOCKED);
@@ -289,6 +297,8 @@
 	struct lm_lockstruct *ls = &sdp->sd_lockstruct;
 	int error;
 
+	BUG_ON(!__lockref_is_dead(&gl->gl_lockref));
+
 	if (gl->gl_lksb.sb_lkid == 0) {
 		gfs2_glock_free(gl);
 		return;
@@ -308,7 +318,7 @@
 
 	if (test_bit(SDF_SKIP_DLM_UNLOCK, &sdp->sd_flags) &&
 	    !gl->gl_lksb.sb_lvbptr) {
-		gfs2_glock_free(gl);
+		gfs2_glock_free_later(gl);
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/log.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/log.c
@@ -1094,7 +1094,8 @@
 	lops_before_commit(sdp, tr);
 	if (gfs2_withdrawn(sdp))
 		goto out_withdraw;
-	gfs2_log_submit_bio(&sdp->sd_jdesc->jd_log_bio, REQ_OP_WRITE);
+	if (sdp->sd_jdesc)
+		gfs2_log_submit_bio(&sdp->sd_jdesc->jd_log_bio, REQ_OP_WRITE);
 	if (gfs2_withdrawn(sdp))
 		goto out_withdraw;
 
@@ -1277,9 +1278,6 @@
 {
 	unsigned int used_blocks = sdp->sd_jdesc->jd_blocks - atomic_read(&sdp->sd_log_blks_free);
 
-	if (test_and_clear_bit(SDF_FORCE_AIL_FLUSH, &sdp->sd_flags))
-		return 1;
-
 	return used_blocks + atomic_read(&sdp->sd_log_blks_needed) >=
 		atomic_read(&sdp->sd_log_thresh2);
 }
@@ -1296,7 +1294,6 @@
 {
 	struct gfs2_sbd *sdp = data;
 	unsigned long t = 1;
-	DEFINE_WAIT(wait);
 
 	while (!kthread_should_stop()) {
 
@@ -1321,7 +1318,9 @@
 						  GFS2_LFC_LOGD_JFLUSH_REQD);
 		}
 
-		if (gfs2_ail_flush_reqd(sdp)) {
+		if (test_bit(SDF_FORCE_AIL_FLUSH, &sdp->sd_flags) ||
+		    gfs2_ail_flush_reqd(sdp)) {
+			clear_bit(SDF_FORCE_AIL_FLUSH, &sdp->sd_flags);
 			gfs2_ail1_start(sdp);
 			gfs2_ail1_wait(sdp);
 			gfs2_ail1_empty(sdp, 0);
@@ -1333,17 +1332,12 @@
 
 		try_to_freeze();
 
-		do {
-			prepare_to_wait(&sdp->sd_logd_waitq, &wait,
-					TASK_INTERRUPTIBLE);
-			if (!gfs2_ail_flush_reqd(sdp) &&
-			    !gfs2_jrnl_flush_reqd(sdp) &&
-			    !kthread_should_stop())
-				t = schedule_timeout(t);
-		} while(t && !gfs2_ail_flush_reqd(sdp) &&
-			!gfs2_jrnl_flush_reqd(sdp) &&
-			!kthread_should_stop());
-		finish_wait(&sdp->sd_logd_waitq, &wait);
+		t = wait_event_interruptible_timeout(sdp->sd_logd_waitq,
+				test_bit(SDF_FORCE_AIL_FLUSH, &sdp->sd_flags) ||
+				gfs2_ail_flush_reqd(sdp) ||
+				gfs2_jrnl_flush_reqd(sdp) ||
+				kthread_should_stop(),
+				t);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/ops_fstype.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/ops_fstype.c
@@ -87,7 +87,7 @@
 	set_bit(SDF_NOJOURNALID, &sdp->sd_flags);
 	gfs2_tune_init(&sdp->sd_tune);
 
-	init_waitqueue_head(&sdp->sd_glock_wait);
+	init_waitqueue_head(&sdp->sd_kill_wait);
 	init_waitqueue_head(&sdp->sd_async_glock_wait);
 	atomic_set(&sdp->sd_glock_disposal, 0);
 	init_completion(&sdp->sd_locking_init);
@@ -139,6 +139,7 @@
 	init_waitqueue_head(&sdp->sd_log_flush_wait);
 	atomic_set(&sdp->sd_freeze_state, SFS_UNFROZEN);
 	mutex_init(&sdp->sd_freeze_mutex);
+	INIT_LIST_HEAD(&sdp->sd_dead_glocks);
 
 	return sdp;
 
@@ -180,7 +181,10 @@
 		pr_warn("Invalid block size\n");
 		return -EINVAL;
 	}
-
+	if (sb->sb_bsize_shift != ffs(sb->sb_bsize) - 1) {
+		pr_warn("Invalid block size shift\n");
+		return -EINVAL;
+	}
 	return 0;
 }
 
@@ -385,8 +389,10 @@
 	if (!table[0])
 		table = sdp->sd_vfs->s_id;
 
-	strlcpy(sdp->sd_proto_name, proto, GFS2_FSNAME_LEN);
-	strlcpy(sdp->sd_table_name, table, GFS2_FSNAME_LEN);
+	BUILD_BUG_ON(GFS2_LOCKNAME_LEN > GFS2_FSNAME_LEN);
+
+	strscpy(sdp->sd_proto_name, proto, GFS2_LOCKNAME_LEN);
+	strscpy(sdp->sd_table_name, table, GFS2_LOCKNAME_LEN);
 
 	table = sdp->sd_table_name;
 	while ((table = strchr(table, '/')))
@@ -1443,13 +1449,13 @@
 
 	switch (o) {
 	case Opt_lockproto:
-		strlcpy(args->ar_lockproto, param->string, GFS2_LOCKNAME_LEN);
+		strscpy(args->ar_lockproto, param->string, GFS2_LOCKNAME_LEN);
 		break;
 	case Opt_locktable:
-		strlcpy(args->ar_locktable, param->string, GFS2_LOCKNAME_LEN);
+		strscpy(args->ar_locktable, param->string, GFS2_LOCKNAME_LEN);
 		break;
 	case Opt_hostdata:
-		strlcpy(args->ar_hostdata, param->string, GFS2_LOCKNAME_LEN);
+		strscpy(args->ar_hostdata, param->string, GFS2_LOCKNAME_LEN);
 		break;
 	case Opt_spectator:
 		args->ar_spectator = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/quota.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/quota.c
@@ -431,6 +431,17 @@
 	    (sync_gen && (qd->qd_sync_gen >= *sync_gen)))
 		return 0;
 
+	/*
+	 * If qd_change is 0 it means a pending quota change was negated.
+	 * We should not sync it, but we still have a qd reference and slot
+	 * reference taken by gfs2_quota_change -> do_qc that need to be put.
+	 */
+	if (!qd->qd_change && test_and_clear_bit(QDF_CHANGE, &qd->qd_flags)) {
+		slot_put(qd);
+		qd_put(qd);
+		return 0;
+	}
+
 	if (!lockref_get_not_dead(&qd->qd_lockref))
 		return 0;
 
@@ -531,34 +542,42 @@
  */
 int gfs2_qa_get(struct gfs2_inode *ip)
 {
-	int error = 0;
 	struct gfs2_sbd *sdp = GFS2_SB(&ip->i_inode);
+	struct inode *inode = &ip->i_inode;
 
 	if (sdp->sd_args.ar_quota == GFS2_QUOTA_OFF)
 		return 0;
 
-	down_write(&ip->i_rw_mutex);
+	spin_lock(&inode->i_lock);
 	if (ip->i_qadata == NULL) {
-		ip->i_qadata = kmem_cache_zalloc(gfs2_qadata_cachep, GFP_NOFS);
-		if (!ip->i_qadata) {
-			error = -ENOMEM;
-			goto out;
-		}
+		struct gfs2_qadata *tmp;
+
+		spin_unlock(&inode->i_lock);
+		tmp = kmem_cache_zalloc(gfs2_qadata_cachep, GFP_NOFS);
+		if (!tmp)
+			return -ENOMEM;
+
+		spin_lock(&inode->i_lock);
+		if (ip->i_qadata == NULL)
+			ip->i_qadata = tmp;
+		else
+			kmem_cache_free(gfs2_qadata_cachep, tmp);
 	}
 	ip->i_qadata->qa_ref++;
-out:
-	up_write(&ip->i_rw_mutex);
-	return error;
+	spin_unlock(&inode->i_lock);
+	return 0;
 }
 
 void gfs2_qa_put(struct gfs2_inode *ip)
 {
-	down_write(&ip->i_rw_mutex);
+	struct inode *inode = &ip->i_inode;
+
+	spin_lock(&inode->i_lock);
 	if (ip->i_qadata && --ip->i_qadata->qa_ref == 0) {
 		kmem_cache_free(gfs2_qadata_cachep, ip->i_qadata);
 		ip->i_qadata = NULL;
 	}
-	up_write(&ip->i_rw_mutex);
+	spin_unlock(&inode->i_lock);
 }
 
 int gfs2_quota_hold(struct gfs2_inode *ip, kuid_t uid, kgid_t gid)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/rgrp.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/rgrp.c
@@ -680,13 +680,14 @@
 /**
  * gfs2_rs_delete - delete a multi-block reservation
  * @ip: The inode for this reservation
- * @wcount: The inode's write count, or NULL
  *
  */
-void gfs2_rs_delete(struct gfs2_inode *ip, atomic_t *wcount)
+void gfs2_rs_delete(struct gfs2_inode *ip)
 {
+	struct inode *inode = &ip->i_inode;
+
 	down_write(&ip->i_rw_mutex);
-	if ((wcount == NULL) || (atomic_read(wcount) <= 1))
+	if (atomic_read(&inode->i_writecount) <= 1)
 		gfs2_rs_deltree(&ip->i_res);
 	up_write(&ip->i_rw_mutex);
 }
@@ -922,15 +923,15 @@
 	spin_lock_init(&rgd->rd_rsspin);
 	mutex_init(&rgd->rd_mutex);
 
-	error = compute_bitstructs(rgd);
-	if (error)
-		goto fail;
-
 	error = gfs2_glock_get(sdp, rgd->rd_addr,
 			       &gfs2_rgrp_glops, CREATE, &rgd->rd_gl);
 	if (error)
 		goto fail;
 
+	error = compute_bitstructs(rgd);
+	if (error)
+		goto fail_glock;
+
 	rgd->rd_rgl = (struct gfs2_rgrp_lvb *)rgd->rd_gl->gl_lksb.sb_lvbptr;
 	rgd->rd_flags &= ~(GFS2_RDF_UPTODATE | GFS2_RDF_PREFERRED);
 	if (rgd->rd_data > sdp->sd_max_rg_data)
@@ -944,6 +945,7 @@
 	}
 
 	error = 0; /* someone else read in the rgrp; free it and ignore it */
+fail_glock:
 	gfs2_glock_put(rgd->rd_gl);
 
 fail:
@@ -1427,7 +1429,8 @@
 
 	start = r.start >> bs_shift;
 	end = start + (r.len >> bs_shift);
-	minlen = max_t(u64, r.minlen,
+	minlen = max_t(u64, r.minlen, sdp->sd_sb.sb_bsize);
+	minlen = max_t(u64, minlen,
 		       q->limits.discard_granularity) >> bs_shift;
 
 	if (end <= start || minlen > sdp->sd_max_rg_data)
@@ -2313,7 +2316,7 @@
 		       (unsigned long long)rgd->rd_addr, rgd->rd_flags,
 		       rgd->rd_free, rgd->rd_free_clone, rgd->rd_dinodes,
 		       rgd->rd_requested, rgd->rd_reserved, rgd->rd_extfail_pt);
-	if (rgd->rd_sbd->sd_args.ar_rgrplvb) {
+	if (rgd->rd_sbd->sd_args.ar_rgrplvb && rgd->rd_rgl) {
 		struct gfs2_rgrp_lvb *rgl = rgd->rd_rgl;
 
 		gfs2_print_dbg(seq, "%s  L: f:%02x b:%u i:%u\n", fs_id_buf,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/rgrp.h
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/rgrp.h
@@ -45,7 +45,7 @@
 			     bool dinode, u64 *generation);
 
 extern void gfs2_rs_deltree(struct gfs2_blkreserv *rs);
-extern void gfs2_rs_delete(struct gfs2_inode *ip, atomic_t *wcount);
+extern void gfs2_rs_delete(struct gfs2_inode *ip);
 extern void __gfs2_free_blocks(struct gfs2_inode *ip, struct gfs2_rgrpd *rgd,
 			       u64 bstart, u32 blen, int meta);
 extern void gfs2_free_meta(struct gfs2_inode *ip, struct gfs2_rgrpd *rgd,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/super.c
@@ -67,9 +67,13 @@
 	sdp->sd_journals = 0;
 	spin_unlock(&sdp->sd_jindex_spin);
 
+	down_write(&sdp->sd_log_flush_lock);
 	sdp->sd_jdesc = NULL;
+	up_write(&sdp->sd_log_flush_lock);
+
 	while (!list_empty(&list)) {
 		jd = list_first_entry(&list, struct gfs2_jdesc, jd_list);
+		BUG_ON(jd->jd_log_bio);
 		gfs2_free_journal_extents(jd);
 		list_del(&jd->jd_list);
 		iput(jd->jd_inode);
@@ -138,8 +142,10 @@
 		return -EIO;
 
 	error = gfs2_find_jhead(sdp->sd_jdesc, &head, false);
-	if (error || gfs2_withdrawn(sdp))
+	if (error) {
+		gfs2_consist(sdp);
 		return error;
+	}
 
 	if (!(head.lh_flags & GFS2_LOG_HEAD_UNMOUNT)) {
 		gfs2_consist(sdp);
@@ -151,7 +157,9 @@
 	gfs2_log_pointers_init(sdp, head.lh_blkno);
 
 	error = gfs2_quota_init(sdp);
-	if (!error && !gfs2_withdrawn(sdp))
+	if (!error && gfs2_withdrawn(sdp))
+		error = -EIO;
+	if (!error)
 		set_bit(SDF_JOURNAL_LIVE, &sdp->sd_flags);
 	return error;
 }
@@ -378,6 +386,7 @@
 
 void gfs2_dinode_out(const struct gfs2_inode *ip, void *buf)
 {
+	const struct inode *inode = &ip->i_inode;
 	struct gfs2_dinode *str = buf;
 
 	str->di_header.mh_magic = cpu_to_be32(GFS2_MAGIC);
@@ -385,15 +394,15 @@
 	str->di_header.mh_format = cpu_to_be32(GFS2_FORMAT_DI);
 	str->di_num.no_addr = cpu_to_be64(ip->i_no_addr);
 	str->di_num.no_formal_ino = cpu_to_be64(ip->i_no_formal_ino);
-	str->di_mode = cpu_to_be32(ip->i_inode.i_mode);
-	str->di_uid = cpu_to_be32(i_uid_read(&ip->i_inode));
-	str->di_gid = cpu_to_be32(i_gid_read(&ip->i_inode));
-	str->di_nlink = cpu_to_be32(ip->i_inode.i_nlink);
-	str->di_size = cpu_to_be64(i_size_read(&ip->i_inode));
-	str->di_blocks = cpu_to_be64(gfs2_get_inode_blocks(&ip->i_inode));
-	str->di_atime = cpu_to_be64(ip->i_inode.i_atime.tv_sec);
-	str->di_mtime = cpu_to_be64(ip->i_inode.i_mtime.tv_sec);
-	str->di_ctime = cpu_to_be64(ip->i_inode.i_ctime.tv_sec);
+	str->di_mode = cpu_to_be32(inode->i_mode);
+	str->di_uid = cpu_to_be32(i_uid_read(inode));
+	str->di_gid = cpu_to_be32(i_gid_read(inode));
+	str->di_nlink = cpu_to_be32(inode->i_nlink);
+	str->di_size = cpu_to_be64(i_size_read(inode));
+	str->di_blocks = cpu_to_be64(gfs2_get_inode_blocks(inode));
+	str->di_atime = cpu_to_be64(inode->i_atime.tv_sec);
+	str->di_mtime = cpu_to_be64(inode->i_mtime.tv_sec);
+	str->di_ctime = cpu_to_be64(inode->i_ctime.tv_sec);
 
 	str->di_goal_meta = cpu_to_be64(ip->i_goal);
 	str->di_goal_data = cpu_to_be64(ip->i_goal);
@@ -401,16 +410,16 @@
 
 	str->di_flags = cpu_to_be32(ip->i_diskflags);
 	str->di_height = cpu_to_be16(ip->i_height);
-	str->di_payload_format = cpu_to_be32(S_ISDIR(ip->i_inode.i_mode) &&
+	str->di_payload_format = cpu_to_be32(S_ISDIR(inode->i_mode) &&
 					     !(ip->i_diskflags & GFS2_DIF_EXHASH) ?
 					     GFS2_FORMAT_DE : 0);
 	str->di_depth = cpu_to_be16(ip->i_depth);
 	str->di_entries = cpu_to_be32(ip->i_entries);
 
 	str->di_eattr = cpu_to_be64(ip->i_eattr);
-	str->di_atime_nsec = cpu_to_be32(ip->i_inode.i_atime.tv_nsec);
-	str->di_mtime_nsec = cpu_to_be32(ip->i_inode.i_mtime.tv_nsec);
-	str->di_ctime_nsec = cpu_to_be32(ip->i_inode.i_ctime.tv_nsec);
+	str->di_atime_nsec = cpu_to_be32(inode->i_atime.tv_nsec);
+	str->di_mtime_nsec = cpu_to_be32(inode->i_mtime.tv_nsec);
+	str->di_ctime_nsec = cpu_to_be32(inode->i_ctime.tv_nsec);
 }
 
 /**
@@ -585,6 +594,8 @@
 
 	if (!sb_rdonly(sb)) {
 		gfs2_make_fs_ro(sdp);
+	} else {
+		gfs2_quota_cleanup(sdp);
 	}
 	WARN_ON(gfs2_withdrawing(sdp));
 
@@ -619,10 +630,7 @@
 	gfs2_gl_hash_clear(sdp);
 	truncate_inode_pages_final(&sdp->sd_aspace);
 	gfs2_delete_debugfs_file(sdp);
-	/*  Unmount the locking protocol  */
-	gfs2_lm_unmount(sdp);
 
-	/*  At this point, we're through participating in the lockspace  */
 	gfs2_sys_fs_del(sdp);
 	free_sbd(sdp);
 }
@@ -975,7 +983,14 @@
 {
 	struct gfs2_sbd *sdp = root->d_sb->s_fs_info;
 	struct gfs2_args *args = &sdp->sd_args;
-	int val;
+	unsigned int logd_secs, statfs_slow, statfs_quantum, quota_quantum;
+
+	spin_lock(&sdp->sd_tune.gt_spin);
+	logd_secs = sdp->sd_tune.gt_logd_secs;
+	quota_quantum = sdp->sd_tune.gt_quota_quantum;
+	statfs_quantum = sdp->sd_tune.gt_statfs_quantum;
+	statfs_slow = sdp->sd_tune.gt_statfs_slow;
+	spin_unlock(&sdp->sd_tune.gt_spin);
 
 	if (is_ancestor(root, sdp->sd_master_dir))
 		seq_puts(s, ",meta");
@@ -1030,17 +1045,14 @@
 	}
 	if (args->ar_discard)
 		seq_puts(s, ",discard");
-	val = sdp->sd_tune.gt_logd_secs;
-	if (val != 30)
-		seq_printf(s, ",commit=%d", val);
-	val = sdp->sd_tune.gt_statfs_quantum;
-	if (val != 30)
-		seq_printf(s, ",statfs_quantum=%d", val);
-	else if (sdp->sd_tune.gt_statfs_slow)
+	if (logd_secs != 30)
+		seq_printf(s, ",commit=%d", logd_secs);
+	if (statfs_quantum != 30)
+		seq_printf(s, ",statfs_quantum=%d", statfs_quantum);
+	else if (statfs_slow)
 		seq_puts(s, ",statfs_quantum=0");
-	val = sdp->sd_tune.gt_quota_quantum;
-	if (val != 60)
-		seq_printf(s, ",quota_quantum=%d", val);
+	if (quota_quantum != 60)
+		seq_printf(s, ",quota_quantum=%d", quota_quantum);
 	if (args->ar_statfs_percent)
 		seq_printf(s, ",statfs_percent=%d", args->ar_statfs_percent);
 	if (args->ar_errors != GFS2_ERRORS_DEFAULT) {
@@ -1376,6 +1388,14 @@
 	if (inode->i_nlink || sb_rdonly(sb))
 		goto out;
 
+	/*
+	 * In case of an incomplete mount, gfs2_evict_inode() may be called for
+	 * system files without having an active journal to write to.  In that
+	 * case, skip the filesystem evict.
+	 */
+	if (!sdp->sd_jdesc)
+		goto out;
+
 	gfs2_holder_mark_uninitialized(&gh);
 	ret = evict_should_delete(inode, &gh);
 	if (ret == SHOULD_DEFER_EVICTION)
@@ -1398,17 +1418,10 @@
 	truncate_inode_pages_final(&inode->i_data);
 	if (ip->i_qadata)
 		gfs2_assert_warn(sdp, ip->i_qadata->qa_ref == 0);
-	gfs2_rs_delete(ip, NULL);
+	gfs2_rs_deltree(&ip->i_res);
 	gfs2_ordered_del_inode(ip);
 	clear_inode(inode);
 	gfs2_dir_hash_inval(ip);
-	if (ip->i_gl) {
-		glock_clear_object(ip->i_gl, ip);
-		wait_on_bit_io(&ip->i_flags, GIF_GLOP_PENDING, TASK_UNINTERRUPTIBLE);
-		gfs2_glock_add_to_lru(ip->i_gl);
-		gfs2_glock_put_eventually(ip->i_gl);
-		ip->i_gl = NULL;
-	}
 	if (gfs2_holder_initialized(&ip->i_iopen_gh)) {
 		struct gfs2_glock *gl = ip->i_iopen_gh.gh_gl;
 
@@ -1421,6 +1434,13 @@
 		gfs2_holder_uninit(&ip->i_iopen_gh);
 		gfs2_glock_put_eventually(gl);
 	}
+	if (ip->i_gl) {
+		glock_clear_object(ip->i_gl, ip);
+		wait_on_bit_io(&ip->i_flags, GIF_GLOP_PENDING, TASK_UNINTERRUPTIBLE);
+		gfs2_glock_add_to_lru(ip->i_gl);
+		gfs2_glock_put_eventually(ip->i_gl);
+		rcu_assign_pointer(ip->i_gl, NULL);
+	}
 }
 
 static struct inode *gfs2_alloc_inode(struct super_block *sb)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/gfs2/util.c
+++ linux-xilinx-zynqmp-5.15.0/fs/gfs2/util.c
@@ -351,7 +351,6 @@
 			fs_err(sdp, "telling LM to unmount\n");
 			lm->lm_unmount(sdp);
 		}
-		set_bit(SDF_SKIP_DLM_UNLOCK, &sdp->sd_flags);
 		fs_err(sdp, "File system withdrawn\n");
 		dump_stack();
 		clear_bit(SDF_WITHDRAW_IN_PROG, &sdp->sd_flags);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfs/bnode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfs/bnode.c
@@ -58,7 +58,7 @@
 	return data;
 }
 
-void hfs_bnode_read_key(struct hfs_bnode *node, void *key, int off)
+int hfs_bnode_read_key(struct hfs_bnode *node, void *key, int off)
 {
 	struct hfs_btree *tree;
 	int key_len;
@@ -70,7 +70,13 @@
 	else
 		key_len = tree->max_key_len + 1;
 
+	if (key_len > tree->max_key_len + 1) {
+		pr_err("key_len %d too large\n", key_len);
+		return -EINVAL;
+	}
+
 	hfs_bnode_read(node, key, off, key_len);
+	return 0;
 }
 
 void hfs_bnode_write(struct hfs_bnode *node, void *buf, int off, int len)
@@ -281,6 +287,7 @@
 		tree->node_hash[hash] = node;
 		tree->node_hash_cnt++;
 	} else {
+		hfs_bnode_get(node2);
 		spin_unlock(&tree->hash_lock);
 		kfree(node);
 		wait_event(node2->lock_wq, !test_bit(HFS_BNODE_NEW, &node2->flags));
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfs/brec.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfs/brec.c
@@ -70,6 +70,7 @@
 	int data_off, end_off;
 	int idx_rec_off, data_rec_off, end_rec_off;
 	__be32 cnid;
+	int res;
 
 	tree = fd->tree;
 	if (!fd->bnode) {
@@ -138,7 +139,10 @@
 	 * at the start of the node and it is not the new node
 	 */
 	if (!rec && new_node != node) {
-		hfs_bnode_read_key(node, fd->search_key, data_off + size);
+		res = hfs_bnode_read_key(node, fd->search_key, data_off + size);
+		if (res < 0)
+			return res;
+
 		hfs_brec_update_parent(fd);
 	}
 
@@ -156,7 +160,10 @@
 		entry_len = sizeof(cnid);
 
 		/* get index key */
-		hfs_bnode_read_key(new_node, fd->search_key, 14);
+		res = hfs_bnode_read_key(new_node, fd->search_key, 14);
+		if (res < 0)
+			return res;
+
 		__hfs_brec_find(fd->bnode, fd);
 
 		hfs_bnode_put(new_node);
@@ -356,6 +363,7 @@
 	int newkeylen, diff;
 	int rec, rec_off, end_rec_off;
 	int start_off, end_off;
+	int res;
 
 	tree = fd->tree;
 	node = fd->bnode;
@@ -431,7 +439,10 @@
 		}
 		fd->bnode = hfs_bnode_find(tree, new_node->parent);
 		/* create index key and entry */
-		hfs_bnode_read_key(new_node, fd->search_key, 14);
+		res = hfs_bnode_read_key(new_node, fd->search_key, 14);
+		if (res < 0)
+			return res;
+
 		cnid = cpu_to_be32(new_node->this);
 
 		__hfs_brec_find(fd->bnode, fd);
@@ -443,7 +454,9 @@
 			if (new_node == node)
 				goto out;
 			/* restore search_key */
-			hfs_bnode_read_key(node, fd->search_key, 14);
+			res = hfs_bnode_read_key(node, fd->search_key, 14);
+			if (res < 0)
+				return res;
 		}
 		new_node = NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfs/btree.h
+++ linux-xilinx-zynqmp-5.15.0/fs/hfs/btree.h
@@ -97,7 +97,7 @@
 extern void hfs_bnode_read(struct hfs_bnode *, void *, int, int);
 extern u16 hfs_bnode_read_u16(struct hfs_bnode *, int);
 extern u8 hfs_bnode_read_u8(struct hfs_bnode *, int);
-extern void hfs_bnode_read_key(struct hfs_bnode *, void *, int);
+extern int hfs_bnode_read_key(struct hfs_bnode *, void *, int);
 extern void hfs_bnode_write(struct hfs_bnode *, void *, int, int);
 extern void hfs_bnode_write_u16(struct hfs_bnode *, int, u16);
 extern void hfs_bnode_write_u8(struct hfs_bnode *, int, u8);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfs/inode.c
@@ -202,6 +202,7 @@
 	HFS_I(inode)->flags = 0;
 	HFS_I(inode)->rsrc_inode = NULL;
 	HFS_I(inode)->fs_blocks = 0;
+	HFS_I(inode)->tz_secondswest = sys_tz.tz_minuteswest * 60;
 	if (S_ISDIR(mode)) {
 		inode->i_size = 2;
 		HFS_SB(sb)->folder_count++;
@@ -277,6 +278,8 @@
 	for (count = 0, i = 0; i < 3; i++)
 		count += be16_to_cpu(ext[i].count);
 	HFS_I(inode)->first_blocks = count;
+	HFS_I(inode)->cached_start = 0;
+	HFS_I(inode)->cached_blocks = 0;
 
 	inode->i_size = HFS_I(inode)->phys_size = log_size;
 	HFS_I(inode)->fs_blocks = (log_size + sb->s_blocksize - 1) >> sb->s_blocksize_bits;
@@ -456,14 +459,16 @@
 		/* panic? */
 		return -EIO;
 
+	res = -EIO;
+	if (HFS_I(main_inode)->cat_key.CName.len > HFS_NAMELEN)
+		goto out;
 	fd.search_key->cat = HFS_I(main_inode)->cat_key;
 	if (hfs_brec_find(&fd))
-		/* panic? */
 		goto out;
 
 	if (S_ISDIR(main_inode->i_mode)) {
 		if (fd.entrylength < sizeof(struct hfs_cat_dir))
-			/* panic? */;
+			goto out;
 		hfs_bnode_read(fd.bnode, &rec, fd.entryoffset,
 			   sizeof(struct hfs_cat_dir));
 		if (rec.type != HFS_CDR_DIR ||
@@ -476,6 +481,8 @@
 		hfs_bnode_write(fd.bnode, &rec, fd.entryoffset,
 			    sizeof(struct hfs_cat_dir));
 	} else if (HFS_IS_RSRC(inode)) {
+		if (fd.entrylength < sizeof(struct hfs_cat_file))
+			goto out;
 		hfs_bnode_read(fd.bnode, &rec, fd.entryoffset,
 			       sizeof(struct hfs_cat_file));
 		hfs_inode_write_fork(inode, rec.file.RExtRec,
@@ -484,7 +491,7 @@
 				sizeof(struct hfs_cat_file));
 	} else {
 		if (fd.entrylength < sizeof(struct hfs_cat_file))
-			/* panic? */;
+			goto out;
 		hfs_bnode_read(fd.bnode, &rec, fd.entryoffset,
 			   sizeof(struct hfs_cat_file));
 		if (rec.type != HFS_CDR_FIL ||
@@ -501,9 +508,10 @@
 		hfs_bnode_write(fd.bnode, &rec, fd.entryoffset,
 			    sizeof(struct hfs_cat_file));
 	}
+	res = 0;
 out:
 	hfs_find_exit(&fd);
-	return 0;
+	return res;
 }
 
 static struct dentry *hfs_file_lookup(struct inode *dir, struct dentry *dentry,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfs/super.c
@@ -418,11 +418,13 @@
 		goto bail_no_root;
 	res = hfs_cat_find_brec(sb, HFS_ROOT_CNID, &fd);
 	if (!res) {
-		if (fd.entrylength > sizeof(rec) || fd.entrylength < 0) {
+		if (fd.entrylength != sizeof(rec.dir)) {
 			res =  -EIO;
 			goto bail_hfs_find;
 		}
 		hfs_bnode_read(fd.bnode, &rec, fd.entryoffset, fd.entrylength);
+		if (rec.type != HFS_CDR_DIR)
+			res = -EIO;
 	}
 	if (res)
 		goto bail_hfs_find;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfs/trans.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfs/trans.c
@@ -109,7 +109,7 @@
 	if (nls_io) {
 		wchar_t ch;
 
-		while (srclen > 0) {
+		while (srclen > 0 && dstlen > 0) {
 			size = nls_io->char2uni(src, srclen, &ch);
 			if (size < 0) {
 				ch = '?';
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/bfind.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/bfind.c
@@ -25,19 +25,8 @@
 	fd->key = ptr + tree->max_key_len + 2;
 	hfs_dbg(BNODE_REFS, "find_init: %d (%p)\n",
 		tree->cnid, __builtin_return_address(0));
-	switch (tree->cnid) {
-	case HFSPLUS_CAT_CNID:
-		mutex_lock_nested(&tree->tree_lock, CATALOG_BTREE_MUTEX);
-		break;
-	case HFSPLUS_EXT_CNID:
-		mutex_lock_nested(&tree->tree_lock, EXTENTS_BTREE_MUTEX);
-		break;
-	case HFSPLUS_ATTR_CNID:
-		mutex_lock_nested(&tree->tree_lock, ATTR_BTREE_MUTEX);
-		break;
-	default:
-		BUG();
-	}
+	mutex_lock_nested(&tree->tree_lock,
+			hfsplus_btree_lock_class(tree));
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/bnode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/bnode.c
@@ -56,7 +56,7 @@
 	return data;
 }
 
-void hfs_bnode_read_key(struct hfs_bnode *node, void *key, int off)
+int hfs_bnode_read_key(struct hfs_bnode *node, void *key, int off)
 {
 	struct hfs_btree *tree;
 	int key_len;
@@ -69,7 +69,13 @@
 	else
 		key_len = tree->max_key_len + 2;
 
+	if (key_len > tree->max_key_len + 2) {
+		pr_err("key_len %d too large\n", key_len);
+		return -EINVAL;
+	}
+
 	hfs_bnode_read(node, key, off, key_len);
+	return 0;
 }
 
 void hfs_bnode_write(struct hfs_bnode *node, void *buf, int off, int len)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/brec.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/brec.c
@@ -68,6 +68,7 @@
 	int data_off, end_off;
 	int idx_rec_off, data_rec_off, end_rec_off;
 	__be32 cnid;
+	int res;
 
 	tree = fd->tree;
 	if (!fd->bnode) {
@@ -138,7 +139,10 @@
 	 * at the start of the node and it is not the new node
 	 */
 	if (!rec && new_node != node) {
-		hfs_bnode_read_key(node, fd->search_key, data_off + size);
+		res = hfs_bnode_read_key(node, fd->search_key, data_off + size);
+		if (res < 0)
+			return res;
+
 		hfs_brec_update_parent(fd);
 	}
 
@@ -156,7 +160,10 @@
 		entry_len = sizeof(cnid);
 
 		/* get index key */
-		hfs_bnode_read_key(new_node, fd->search_key, 14);
+		res = hfs_bnode_read_key(new_node, fd->search_key, 14);
+		if (res < 0)
+			return res;
+
 		__hfs_brec_find(fd->bnode, fd, hfs_find_rec_by_key);
 
 		hfs_bnode_put(new_node);
@@ -360,6 +367,7 @@
 	int newkeylen, diff;
 	int rec, rec_off, end_rec_off;
 	int start_off, end_off;
+	int res;
 
 	tree = fd->tree;
 	node = fd->bnode;
@@ -435,7 +443,10 @@
 		}
 		fd->bnode = hfs_bnode_find(tree, new_node->parent);
 		/* create index key and entry */
-		hfs_bnode_read_key(new_node, fd->search_key, 14);
+		res = hfs_bnode_read_key(new_node, fd->search_key, 14);
+		if (res < 0)
+			return res;
+
 		cnid = cpu_to_be32(new_node->this);
 
 		__hfs_brec_find(fd->bnode, fd, hfs_find_rec_by_key);
@@ -447,7 +458,9 @@
 			if (new_node == node)
 				goto out;
 			/* restore search_key */
-			hfs_bnode_read_key(node, fd->search_key, 14);
+			res = hfs_bnode_read_key(node, fd->search_key, 14);
+			if (res < 0)
+				return res;
 		}
 		new_node = NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/extents.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/extents.c
@@ -430,7 +430,8 @@
 		hfsplus_free_extents(sb, ext_entry, total_blocks - start,
 				     total_blocks);
 		total_blocks = start;
-		mutex_lock(&fd.tree->tree_lock);
+		mutex_lock_nested(&fd.tree->tree_lock,
+			hfsplus_btree_lock_class(fd.tree));
 	} while (total_blocks > blocks);
 	hfs_find_exit(&fd);
 
@@ -592,7 +593,8 @@
 					     alloc_cnt, alloc_cnt - blk_cnt);
 			hfsplus_dump_extent(hip->first_extents);
 			hip->first_blocks = blk_cnt;
-			mutex_lock(&fd.tree->tree_lock);
+			mutex_lock_nested(&fd.tree->tree_lock,
+				hfsplus_btree_lock_class(fd.tree));
 			break;
 		}
 		res = __hfsplus_ext_cache_extent(&fd, inode, alloc_cnt);
@@ -606,7 +608,8 @@
 		hfsplus_free_extents(sb, hip->cached_extents,
 				     alloc_cnt - start, alloc_cnt - blk_cnt);
 		hfsplus_dump_extent(hip->cached_extents);
-		mutex_lock(&fd.tree->tree_lock);
+		mutex_lock_nested(&fd.tree->tree_lock,
+				hfsplus_btree_lock_class(fd.tree));
 		if (blk_cnt > start) {
 			hip->extent_state |= HFSPLUS_EXT_DIRTY;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/hfsplus_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/hfsplus_fs.h
@@ -156,6 +156,7 @@
 
 	/* Runtime variables */
 	u32 blockoffset;
+	u32 min_io_size;
 	sector_t part_start;
 	sector_t sect_count;
 	int fs_shift;
@@ -198,6 +199,8 @@
 #define HFSPLUS_SB_HFSX		3
 #define HFSPLUS_SB_CASEFOLD	4
 #define HFSPLUS_SB_NOBARRIER	5
+#define HFSPLUS_SB_UID		6
+#define HFSPLUS_SB_GID		7
 
 static inline struct hfsplus_sb_info *HFSPLUS_SB(struct super_block *sb)
 {
@@ -304,7 +307,7 @@
  */
 static inline unsigned short hfsplus_min_io_size(struct super_block *sb)
 {
-	return max_t(unsigned short, bdev_logical_block_size(sb->s_bdev),
+	return max_t(unsigned short, HFSPLUS_SB(sb)->min_io_size,
 		     HFSPLUS_SECTOR_SIZE);
 }
 
@@ -393,7 +396,7 @@
 void hfs_bnode_read(struct hfs_bnode *node, void *buf, int off, int len);
 u16 hfs_bnode_read_u16(struct hfs_bnode *node, int off);
 u8 hfs_bnode_read_u8(struct hfs_bnode *node, int off);
-void hfs_bnode_read_key(struct hfs_bnode *node, void *key, int off);
+int hfs_bnode_read_key(struct hfs_bnode *node, void *key, int off);
 void hfs_bnode_write(struct hfs_bnode *node, void *buf, int off, int len);
 void hfs_bnode_write_u16(struct hfs_bnode *node, int off, u16 data);
 void hfs_bnode_clear(struct hfs_bnode *node, int off, int len);
@@ -548,6 +551,27 @@
 	return cpu_to_be32(lower_32_bits(ut) + HFSPLUS_UTC_OFFSET);
 }
 
+static inline enum hfsplus_btree_mutex_classes
+hfsplus_btree_lock_class(struct hfs_btree *tree)
+{
+	enum hfsplus_btree_mutex_classes class;
+
+	switch (tree->cnid) {
+	case HFSPLUS_CAT_CNID:
+		class = CATALOG_BTREE_MUTEX;
+		break;
+	case HFSPLUS_EXT_CNID:
+		class = EXTENTS_BTREE_MUTEX;
+		break;
+	case HFSPLUS_ATTR_CNID:
+		class = ATTR_BTREE_MUTEX;
+		break;
+	default:
+		BUG();
+	}
+	return class;
+}
+
 /* compatibility */
 #define hfsp_mt2ut(t)		(struct timespec64){ .tv_sec = __hfsp_mt2ut(t) }
 #define hfsp_ut2mt(t)		__hfsp_ut2mt((t).tv_sec)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/inode.c
@@ -190,11 +190,11 @@
 	mode = be16_to_cpu(perms->mode);
 
 	i_uid_write(inode, be32_to_cpu(perms->owner));
-	if (!i_uid_read(inode) && !mode)
+	if ((test_bit(HFSPLUS_SB_UID, &sbi->flags)) || (!i_uid_read(inode) && !mode))
 		inode->i_uid = sbi->uid;
 
 	i_gid_write(inode, be32_to_cpu(perms->group));
-	if (!i_gid_read(inode) && !mode)
+	if ((test_bit(HFSPLUS_SB_GID, &sbi->flags)) || (!i_gid_read(inode) && !mode))
 		inode->i_gid = sbi->gid;
 
 	if (dir) {
@@ -509,8 +509,11 @@
 	if (type == HFSPLUS_FOLDER) {
 		struct hfsplus_cat_folder *folder = &entry.folder;
 
-		if (fd->entrylength < sizeof(struct hfsplus_cat_folder))
-			/* panic? */;
+		if (fd->entrylength < sizeof(struct hfsplus_cat_folder)) {
+			pr_err("bad catalog folder entry\n");
+			res = -EIO;
+			goto out;
+		}
 		hfs_bnode_read(fd->bnode, &entry, fd->entryoffset,
 					sizeof(struct hfsplus_cat_folder));
 		hfsplus_get_perms(inode, &folder->permissions, 1);
@@ -530,8 +533,11 @@
 	} else if (type == HFSPLUS_FILE) {
 		struct hfsplus_cat_file *file = &entry.file;
 
-		if (fd->entrylength < sizeof(struct hfsplus_cat_file))
-			/* panic? */;
+		if (fd->entrylength < sizeof(struct hfsplus_cat_file)) {
+			pr_err("bad catalog file entry\n");
+			res = -EIO;
+			goto out;
+		}
 		hfs_bnode_read(fd->bnode, &entry, fd->entryoffset,
 					sizeof(struct hfsplus_cat_file));
 
@@ -562,6 +568,7 @@
 		pr_err("bad catalog entry used to create inode\n");
 		res = -EIO;
 	}
+out:
 	return res;
 }
 
@@ -570,6 +577,7 @@
 	struct inode *main_inode = inode;
 	struct hfs_find_data fd;
 	hfsplus_cat_entry entry;
+	int res = 0;
 
 	if (HFSPLUS_IS_RSRC(inode))
 		main_inode = HFSPLUS_I(inode)->rsrc_inode;
@@ -588,8 +596,11 @@
 	if (S_ISDIR(main_inode->i_mode)) {
 		struct hfsplus_cat_folder *folder = &entry.folder;
 
-		if (fd.entrylength < sizeof(struct hfsplus_cat_folder))
-			/* panic? */;
+		if (fd.entrylength < sizeof(struct hfsplus_cat_folder)) {
+			pr_err("bad catalog folder entry\n");
+			res = -EIO;
+			goto out;
+		}
 		hfs_bnode_read(fd.bnode, &entry, fd.entryoffset,
 					sizeof(struct hfsplus_cat_folder));
 		/* simple node checks? */
@@ -614,8 +625,11 @@
 	} else {
 		struct hfsplus_cat_file *file = &entry.file;
 
-		if (fd.entrylength < sizeof(struct hfsplus_cat_file))
-			/* panic? */;
+		if (fd.entrylength < sizeof(struct hfsplus_cat_file)) {
+			pr_err("bad catalog file entry\n");
+			res = -EIO;
+			goto out;
+		}
 		hfs_bnode_read(fd.bnode, &entry, fd.entryoffset,
 					sizeof(struct hfsplus_cat_file));
 		hfsplus_inode_write_fork(inode, &file->data_fork);
@@ -636,7 +650,7 @@
 	set_bit(HFSPLUS_I_CAT_DIRTY, &HFSPLUS_I(inode)->flags);
 out:
 	hfs_find_exit(&fd);
-	return 0;
+	return res;
 }
 
 int hfsplus_fileattr_get(struct dentry *dentry, struct fileattr *fa)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/options.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/options.c
@@ -140,6 +140,8 @@
 			if (!uid_valid(sbi->uid)) {
 				pr_err("invalid uid specified\n");
 				return 0;
+			} else {
+				set_bit(HFSPLUS_SB_UID, &sbi->flags);
 			}
 			break;
 		case opt_gid:
@@ -151,6 +153,8 @@
 			if (!gid_valid(sbi->gid)) {
 				pr_err("invalid gid specified\n");
 				return 0;
+			} else {
+				set_bit(HFSPLUS_SB_GID, &sbi->flags);
 			}
 			break;
 		case opt_part:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/super.c
@@ -295,11 +295,11 @@
 		hfsplus_sync_fs(sb, 1);
 	}
 
+	iput(sbi->alloc_file);
+	iput(sbi->hidden_dir);
 	hfs_btree_close(sbi->attr_tree);
 	hfs_btree_close(sbi->cat_tree);
 	hfs_btree_close(sbi->ext_tree);
-	iput(sbi->alloc_file);
-	iput(sbi->hidden_dir);
 	kfree(sbi->s_vhdr_buf);
 	kfree(sbi->s_backup_vhdr_buf);
 	unload_nls(sbi->nls);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/wrapper.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/wrapper.c
@@ -173,6 +173,8 @@
 	if (!blocksize)
 		goto out;
 
+	sbi->min_io_size = blocksize;
+
 	if (hfsplus_get_last_session(sb, &part_start, &part_size))
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hfsplus/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hfsplus/xattr.c
@@ -699,7 +699,7 @@
 		return err;
 	}
 
-	strbuf = kmalloc(NLS_MAX_CHARSET_SIZE * HFSPLUS_ATTR_MAX_STRLEN +
+	strbuf = kzalloc(NLS_MAX_CHARSET_SIZE * HFSPLUS_ATTR_MAX_STRLEN +
 			XATTR_MAC_OSX_PREFIX_LEN + 1, GFP_KERNEL);
 	if (!strbuf) {
 		res = -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/hugetlbfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/hugetlbfs/inode.c
@@ -135,6 +135,7 @@
 	loff_t len, vma_len;
 	int ret;
 	struct hstate *h = hstate_file(file);
+	vm_flags_t vm_flags;
 
 	/*
 	 * vma address alignment (but not the pgoff alignment) has
@@ -176,10 +177,20 @@
 	file_accessed(file);
 
 	ret = -ENOMEM;
+
+	vm_flags = vma->vm_flags;
+	/*
+	 * for SHM_HUGETLB, the pages are reserved in the shmget() call so skip
+	 * reserving here. Note: only for SHM hugetlbfs file, the inode
+	 * flag S_PRIVATE is set.
+	 */
+	if (inode->i_flags & S_PRIVATE)
+		vm_flags |= VM_NORESERVE;
+
 	if (!hugetlb_reserve_pages(inode,
 				vma->vm_pgoff >> huge_page_order(h),
 				len >> huge_page_shift(h), vma,
-				vma->vm_flags))
+				vm_flags))
 		goto out;
 
 	ret = 0;
@@ -206,7 +217,7 @@
 	info.flags = 0;
 	info.length = len;
 	info.low_limit = current->mm->mmap_base;
-	info.high_limit = TASK_SIZE;
+	info.high_limit = arch_get_mmap_end(addr);
 	info.align_mask = PAGE_MASK & ~huge_page_mask(h);
 	info.align_offset = 0;
 	return vm_unmapped_area(&info);
@@ -222,7 +233,7 @@
 	info.flags = VM_UNMAPPED_AREA_TOPDOWN;
 	info.length = len;
 	info.low_limit = max(PAGE_SIZE, mmap_min_addr);
-	info.high_limit = current->mm->mmap_base;
+	info.high_limit = arch_get_mmap_base(addr, current->mm->mmap_base);
 	info.align_mask = PAGE_MASK & ~huge_page_mask(h);
 	info.align_offset = 0;
 	addr = vm_unmapped_area(&info);
@@ -237,7 +248,7 @@
 		VM_BUG_ON(addr != -ENOMEM);
 		info.flags = 0;
 		info.low_limit = current->mm->mmap_base;
-		info.high_limit = TASK_SIZE;
+		info.high_limit = arch_get_mmap_end(addr);
 		addr = vm_unmapped_area(&info);
 	}
 
@@ -251,6 +262,7 @@
 	struct mm_struct *mm = current->mm;
 	struct vm_area_struct *vma;
 	struct hstate *h = hstate_file(file);
+	const unsigned long mmap_end = arch_get_mmap_end(addr);
 
 	if (len & ~huge_page_mask(h))
 		return -EINVAL;
@@ -266,7 +278,7 @@
 	if (addr) {
 		addr = ALIGN(addr, huge_page_size(h));
 		vma = find_vma(mm, addr);
-		if (TASK_SIZE - len >= addr &&
+		if (mmap_end - len >= addr &&
 		    (!vma || addr + len <= vm_start_gap(vma)))
 			return addr;
 	}
@@ -360,6 +372,12 @@
 		} else {
 			unlock_page(page);
 
+			if (PageHWPoison(page)) {
+				put_page(page);
+				retval = -EIO;
+				break;
+			}
+
 			/*
 			 * We have the page, copy it to user space buffer.
 			 */
@@ -409,10 +427,11 @@
 	struct vm_area_struct *vma;
 
 	/*
-	 * end == 0 indicates that the entire range after
-	 * start should be unmapped.
+	 * end == 0 indicates that the entire range after start should be
+	 * unmapped.  Note, end is exclusive, whereas the interval tree takes
+	 * an inclusive "last".
 	 */
-	vma_interval_tree_foreach(vma, root, start, end ? end : ULONG_MAX) {
+	vma_interval_tree_foreach(vma, root, start, end ? end - 1 : ULONG_MAX) {
 		unsigned long v_offset;
 		unsigned long v_end;
 
@@ -982,13 +1001,6 @@
 static int hugetlbfs_error_remove_page(struct address_space *mapping,
 				struct page *page)
 {
-	struct inode *inode = mapping->host;
-	pgoff_t index = page->index;
-
-	remove_huge_page(page);
-	if (unlikely(hugetlb_unreserve_pages(inode, index, index + 1, 1)))
-		hugetlb_fix_reserve_counts(inode);
-
 	return 0;
 }
 
@@ -1046,12 +1058,12 @@
 		if (sbinfo->spool) {
 			long free_pages;
 
-			spin_lock(&sbinfo->spool->lock);
+			spin_lock_irq(&sbinfo->spool->lock);
 			buf->f_blocks = sbinfo->spool->max_hpages;
 			free_pages = sbinfo->spool->max_hpages
 				- sbinfo->spool->used_hpages;
 			buf->f_bavail = buf->f_bfree = free_pages;
-			spin_unlock(&sbinfo->spool->lock);
+			spin_unlock_irq(&sbinfo->spool->lock);
 			buf->f_files = sbinfo->max_inodes;
 			buf->f_ffree = sbinfo->free_inodes;
 		}
@@ -1222,6 +1234,7 @@
 {
 	struct hugetlbfs_fs_context *ctx = fc->fs_private;
 	struct fs_parse_result result;
+	struct hstate *h;
 	char *rest;
 	unsigned long ps;
 	int opt;
@@ -1249,7 +1262,7 @@
 
 	case Opt_size:
 		/* memparse() will accept a K/M/G without a digit */
-		if (!isdigit(param->string[0]))
+		if (!param->string || !isdigit(param->string[0]))
 			goto bad_val;
 		ctx->max_size_opt = memparse(param->string, &rest);
 		ctx->max_val_type = SIZE_STD;
@@ -1259,23 +1272,24 @@
 
 	case Opt_nr_inodes:
 		/* memparse() will accept a K/M/G without a digit */
-		if (!isdigit(param->string[0]))
+		if (!param->string || !isdigit(param->string[0]))
 			goto bad_val;
 		ctx->nr_inodes = memparse(param->string, &rest);
 		return 0;
 
 	case Opt_pagesize:
 		ps = memparse(param->string, &rest);
-		ctx->hstate = size_to_hstate(ps);
-		if (!ctx->hstate) {
+		h = size_to_hstate(ps);
+		if (!h) {
 			pr_err("Unsupported page size %lu MB\n", ps >> 20);
 			return -EINVAL;
 		}
+		ctx->hstate = h;
 		return 0;
 
 	case Opt_min_size:
 		/* memparse() will accept a K/M/G without a digit */
-		if (!isdigit(param->string[0]))
+		if (!param->string || !isdigit(param->string[0]))
 			goto bad_val;
 		ctx->min_size_opt = memparse(param->string, &rest);
 		ctx->min_val_type = SIZE_STD;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/inode.c
@@ -27,7 +27,7 @@
  * Inode locking rules:
  *
  * inode->i_lock protects:
- *   inode->i_state, inode->i_hash, __iget()
+ *   inode->i_state, inode->i_hash, __iget(), inode->i_io_list
  * Inode LRU list locks protect:
  *   inode->i_sb->s_inode_lru, inode->i_lru
  * inode->i_sb->s_inode_list_lock protects:
@@ -67,11 +67,6 @@
 };
 EXPORT_SYMBOL(empty_aops);
 
-/*
- * Statistics gathering..
- */
-struct inodes_stat_t inodes_stat;
-
 static DEFINE_PER_CPU(unsigned long, nr_inodes);
 static DEFINE_PER_CPU(unsigned long, nr_unused);
 
@@ -106,13 +101,43 @@
  * Handle nr_inode sysctl
  */
 #ifdef CONFIG_SYSCTL
-int proc_nr_inodes(struct ctl_table *table, int write,
-		   void *buffer, size_t *lenp, loff_t *ppos)
+/*
+ * Statistics gathering..
+ */
+static struct inodes_stat_t inodes_stat;
+
+static int proc_nr_inodes(struct ctl_table *table, int write, void *buffer,
+			  size_t *lenp, loff_t *ppos)
 {
 	inodes_stat.nr_inodes = get_nr_inodes();
 	inodes_stat.nr_unused = get_nr_inodes_unused();
 	return proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
 }
+
+static struct ctl_table inodes_sysctls[] = {
+	{
+		.procname	= "inode-nr",
+		.data		= &inodes_stat,
+		.maxlen		= 2*sizeof(long),
+		.mode		= 0444,
+		.proc_handler	= proc_nr_inodes,
+	},
+	{
+		.procname	= "inode-state",
+		.data		= &inodes_stat,
+		.maxlen		= 7*sizeof(long),
+		.mode		= 0444,
+		.proc_handler	= proc_nr_inodes,
+	},
+	{ }
+};
+
+static int __init init_fs_inode_sysctls(void)
+{
+	register_sysctl_init("fs", inodes_sysctls);
+	return 0;
+}
+early_initcall(init_fs_inode_sysctls);
 #endif
 
 static int no_open(struct inode *inode, struct file *file)
@@ -167,8 +192,6 @@
 	inode->i_wb_frn_history = 0;
 #endif
 
-	if (security_inode_alloc(inode))
-		goto out;
 	spin_lock_init(&inode->i_lock);
 	lockdep_set_class(&inode->i_lock, &sb->s_type->i_lock_key);
 
@@ -205,11 +228,12 @@
 	inode->i_fsnotify_mask = 0;
 #endif
 	inode->i_flctx = NULL;
+
+	if (unlikely(security_inode_alloc(inode)))
+		return -ENOMEM;
 	this_cpu_inc(nr_inodes);
 
 	return 0;
-out:
-	return -ENOMEM;
 }
 EXPORT_SYMBOL(inode_init_always);
 
@@ -457,6 +481,39 @@
 		this_cpu_dec(nr_unused);
 }
 
+static void inode_pin_lru_isolating(struct inode *inode)
+{
+	lockdep_assert_held(&inode->i_lock);
+	WARN_ON(inode->i_state & (I_LRU_ISOLATING | I_FREEING | I_WILL_FREE));
+	inode->i_state |= I_LRU_ISOLATING;
+}
+
+static void inode_unpin_lru_isolating(struct inode *inode)
+{
+	spin_lock(&inode->i_lock);
+	WARN_ON(!(inode->i_state & I_LRU_ISOLATING));
+	inode->i_state &= ~I_LRU_ISOLATING;
+	smp_mb();
+	wake_up_bit(&inode->i_state, __I_LRU_ISOLATING);
+	spin_unlock(&inode->i_lock);
+}
+
+static void inode_wait_for_lru_isolating(struct inode *inode)
+{
+	spin_lock(&inode->i_lock);
+	if (inode->i_state & I_LRU_ISOLATING) {
+		DEFINE_WAIT_BIT(wq, &inode->i_state, __I_LRU_ISOLATING);
+		wait_queue_head_t *wqh;
+
+		wqh = bit_waitqueue(&inode->i_state, __I_LRU_ISOLATING);
+		spin_unlock(&inode->i_lock);
+		__wait_on_bit(wqh, &wq, bit_wait, TASK_UNINTERRUPTIBLE);
+		spin_lock(&inode->i_lock);
+		WARN_ON(inode->i_state & I_LRU_ISOLATING);
+	}
+	spin_unlock(&inode->i_lock);
+}
+
 /**
  * inode_sb_list_add - add inode to the superblock list of inodes
  * @inode: inode to add
@@ -576,6 +633,8 @@
 
 	inode_sb_list_del(inode);
 
+	inode_wait_for_lru_isolating(inode);
+
 	/*
 	 * Wait for flusher thread to be done with the inode so that filesystem
 	 * does not start destroying it while writeback is still running. Since
@@ -644,6 +703,10 @@
 			continue;
 
 		spin_lock(&inode->i_lock);
+		if (atomic_read(&inode->i_count)) {
+			spin_unlock(&inode->i_lock);
+			continue;
+		}
 		if (inode->i_state & (I_NEW | I_FREEING | I_WILL_FREE)) {
 			spin_unlock(&inode->i_lock);
 			continue;
@@ -773,7 +836,7 @@
 	}
 
 	if (inode_has_buffers(inode) || !mapping_empty(&inode->i_data)) {
-		__iget(inode);
+		inode_pin_lru_isolating(inode);
 		spin_unlock(&inode->i_lock);
 		spin_unlock(lru_lock);
 		if (remove_inode_buffers(inode)) {
@@ -786,7 +849,7 @@
 			if (current->reclaim_state)
 				current->reclaim_state->reclaimed_slab += reap;
 		}
-		iput(inode);
+		inode_unpin_lru_isolating(inode);
 		spin_lock(lru_lock);
 		return LRU_RETRY;
 	}
@@ -1025,6 +1088,48 @@
 EXPORT_SYMBOL(discard_new_inode);
 
 /**
+ * lock_two_inodes - lock two inodes (may be regular files but also dirs)
+ *
+ * Lock any non-NULL argument. The caller must make sure that if he is passing
+ * in two directories, one is not ancestor of the other.  Zero, one or two
+ * objects may be locked by this function.
+ *
+ * @inode1: first inode to lock
+ * @inode2: second inode to lock
+ * @subclass1: inode lock subclass for the first lock obtained
+ * @subclass2: inode lock subclass for the second lock obtained
+ */
+void lock_two_inodes(struct inode *inode1, struct inode *inode2,
+		     unsigned subclass1, unsigned subclass2)
+{
+	if (!inode1 || !inode2) {
+		/*
+		 * Make sure @subclass1 will be used for the acquired lock.
+		 * This is not strictly necessary (no current caller cares) but
+		 * let's keep things consistent.
+		 */
+		if (!inode1)
+			swap(inode1, inode2);
+		goto lock;
+	}
+
+	/*
+	 * If one object is directory and the other is not, we must make sure
+	 * to lock directory first as the other object may be its child.
+	 */
+	if (S_ISDIR(inode2->i_mode) == S_ISDIR(inode1->i_mode)) {
+		if (inode1 > inode2)
+			swap(inode1, inode2);
+	} else if (!S_ISDIR(inode1->i_mode))
+		swap(inode1, inode2);
+lock:
+	if (inode1)
+		inode_lock_nested(inode1, subclass1);
+	if (inode2 && inode2 != inode1)
+		inode_lock_nested(inode2, subclass2);
+}
+
+/**
  * lock_two_nondirectories - take two i_mutexes on non-directory objects
  *
  * Lock any non-NULL argument that is not a directory.
@@ -1782,12 +1887,13 @@
  * This does the actual work of updating an inodes time or version.  Must have
  * had called mnt_want_write() before calling this.
  */
-static int update_time(struct inode *inode, struct timespec64 *time, int flags)
+int inode_update_time(struct inode *inode, struct timespec64 *time, int flags)
 {
 	if (inode->i_op->update_time)
 		return inode->i_op->update_time(inode, time, flags);
 	return generic_update_time(inode, time, flags);
 }
+EXPORT_SYMBOL(inode_update_time);
 
 /**
  *	atime_needs_update	-	update the access time
@@ -1857,7 +1963,7 @@
 	 * of the fs read only, e.g. subvolumes in Btrfs.
 	 */
 	now = current_time(inode);
-	update_time(inode, &now, S_ATIME);
+	inode_update_time(inode, &now, S_ATIME);
 	__mnt_drop_write(mnt);
 skip_update:
 	sb_end_write(inode->i_sb);
@@ -1865,40 +1971,12 @@
 EXPORT_SYMBOL(touch_atime);
 
 /*
- * The logic we want is
- *
- *	if suid or (sgid and xgrp)
- *		remove privs
- */
-int should_remove_suid(struct dentry *dentry)
-{
-	umode_t mode = d_inode(dentry)->i_mode;
-	int kill = 0;
-
-	/* suid always must be killed */
-	if (unlikely(mode & S_ISUID))
-		kill = ATTR_KILL_SUID;
-
-	/*
-	 * sgid without any exec bits is just a mandatory locking mark; leave
-	 * it alone.  If some exec bits are set, it's a real sgid; kill it.
-	 */
-	if (unlikely((mode & S_ISGID) && (mode & S_IXGRP)))
-		kill |= ATTR_KILL_SGID;
-
-	if (unlikely(kill && !capable(CAP_FSETID) && S_ISREG(mode)))
-		return kill;
-
-	return 0;
-}
-EXPORT_SYMBOL(should_remove_suid);
-
-/*
  * Return mask of changes for notify_change() that need to be done as a
  * response to write or truncate. Return 0 if nothing has to be changed.
  * Negative value on error (change should be denied).
  */
-int dentry_needs_remove_privs(struct dentry *dentry)
+int dentry_needs_remove_privs(struct user_namespace *mnt_userns,
+			      struct dentry *dentry)
 {
 	struct inode *inode = d_inode(dentry);
 	int mask = 0;
@@ -1907,7 +1985,7 @@
 	if (IS_NOSEC(inode))
 		return 0;
 
-	mask = should_remove_suid(dentry);
+	mask = setattr_should_drop_suidgid(mnt_userns, inode);
 	ret = security_inode_need_killpriv(dentry);
 	if (ret < 0)
 		return ret;
@@ -1949,7 +2027,7 @@
 	if (IS_NOSEC(inode) || !S_ISREG(inode->i_mode))
 		return 0;
 
-	kill = dentry_needs_remove_privs(dentry);
+	kill = dentry_needs_remove_privs(file_mnt_user_ns(file), dentry);
 	if (kill < 0)
 		return kill;
 	if (kill)
@@ -2002,7 +2080,7 @@
 	if (__mnt_want_write_file(file))
 		return 0;
 
-	ret = update_time(inode, &now, sync_it);
+	ret = inode_update_time(inode, &now, sync_it);
 	__mnt_drop_write_file(file);
 
 	return ret;
@@ -2165,10 +2243,6 @@
 		/* Directories are special, and always inherit S_ISGID */
 		if (S_ISDIR(mode))
 			mode |= S_ISGID;
-		else if ((mode & (S_ISGID | S_IXGRP)) == (S_ISGID | S_IXGRP) &&
-			 !in_group_p(i_gid_into_mnt(mnt_userns, dir)) &&
-			 !capable_wrt_inode_uidgid(mnt_userns, dir, CAP_FSETID))
-			mode &= ~S_ISGID;
 	} else
 		inode_fsgid_set(inode, mnt_userns);
 	inode->i_mode = mode;
@@ -2324,3 +2398,69 @@
 	return timestamp_truncate(now, inode);
 }
 EXPORT_SYMBOL(current_time);
+
+/**
+ * inode_set_ctime_current - set the ctime to current_time
+ * @inode: inode
+ *
+ * Set the inode->i_ctime to the current value for the inode. Returns
+ * the current value that was assigned to i_ctime.
+ */
+struct timespec64 inode_set_ctime_current(struct inode *inode)
+{
+	struct timespec64 now = current_time(inode);
+
+	inode_set_ctime(inode, now.tv_sec, now.tv_nsec);
+	return now;
+}
+EXPORT_SYMBOL(inode_set_ctime_current);
+
+/**
+ * in_group_or_capable - check whether caller is CAP_FSETID privileged
+ * @mnt_userns: user namespace of the mount @inode was found from
+ * @inode:	inode to check
+ * @gid:	the new/current gid of @inode
+ *
+ * Check wether @gid is in the caller's group list or if the caller is
+ * privileged with CAP_FSETID over @inode. This can be used to determine
+ * whether the setgid bit can be kept or must be dropped.
+ *
+ * Return: true if the caller is sufficiently privileged, false if not.
+ */
+bool in_group_or_capable(struct user_namespace *mnt_userns,
+			 const struct inode *inode, kgid_t gid)
+{
+	if (in_group_p(gid))
+		return true;
+	if (capable_wrt_inode_uidgid(mnt_userns, inode, CAP_FSETID))
+		return true;
+	return false;
+}
+
+/**
+ * mode_strip_sgid - handle the sgid bit for non-directories
+ * @mnt_userns: User namespace of the mount the inode was created from
+ * @dir: parent directory inode
+ * @mode: mode of the file to be created in @dir
+ *
+ * If the @mode of the new file has both the S_ISGID and S_IXGRP bit
+ * raised and @dir has the S_ISGID bit raised ensure that the caller is
+ * either in the group of the parent directory or they have CAP_FSETID
+ * in their user namespace and are privileged over the parent directory.
+ * In all other cases, strip the S_ISGID bit from @mode.
+ *
+ * Return: the new mode to use for the file
+ */
+umode_t mode_strip_sgid(struct user_namespace *mnt_userns,
+			const struct inode *dir, umode_t mode)
+{
+	if ((mode & (S_ISGID | S_IXGRP)) != (S_ISGID | S_IXGRP))
+		return mode;
+	if (S_ISDIR(mode) || !dir || !(dir->i_mode & S_ISGID))
+		return mode;
+	if (in_group_or_capable(mnt_userns, dir,
+				i_gid_into_mnt(mnt_userns, dir)))
+		return mode;
+	return mode & ~S_ISGID;
+}
+EXPORT_SYMBOL(mode_strip_sgid);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/internal.h
@@ -24,7 +24,6 @@
 extern void __init bdev_cache_init(void);
 
 extern int __sync_blockdev(struct block_device *bdev, int wait);
-void iterate_bdevs(void (*)(struct block_device *, void *), void *);
 void emergency_thaw_bdev(struct super_block *sb);
 #else
 static inline void bdev_cache_init(void)
@@ -35,10 +34,6 @@
 {
 	return 0;
 }
-static inline void iterate_bdevs(void (*f)(struct block_device *, void *),
-		void *arg)
-{
-}
 static inline int emergency_thaw_bdev(struct super_block *sb)
 {
 	return 0;
@@ -69,8 +64,6 @@
  */
 extern int filename_lookup(int dfd, struct filename *name, unsigned flags,
 			   struct path *path, struct path *root);
-extern int vfs_path_lookup(struct dentry *, struct vfsmount *,
-			   const char *, unsigned int, struct path *);
 int do_rmdir(int dfd, struct filename *name);
 int do_unlinkat(int dfd, struct filename *name);
 int may_linkat(struct user_namespace *mnt_userns, struct path *link);
@@ -111,6 +104,16 @@
 extern struct file *alloc_empty_file(int, const struct cred *);
 extern struct file *alloc_empty_file_noaccount(int, const struct cred *);
 
+static inline void put_file_access(struct file *file)
+{
+	if ((file->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ) {
+		i_readcount_dec(file->f_inode);
+	} else if (file->f_mode & FMODE_WRITER) {
+		put_write_access(file->f_inode);
+		__mnt_drop_write(file->f_path.mnt);
+	}
+}
+
 /*
  * super.c
  */
@@ -150,7 +153,11 @@
  */
 extern long prune_icache_sb(struct super_block *sb, struct shrink_control *sc);
 extern void inode_add_lru(struct inode *inode);
-extern int dentry_needs_remove_privs(struct dentry *dentry);
+int dentry_needs_remove_privs(struct user_namespace *, struct dentry *dentry);
+bool in_group_or_capable(struct user_namespace *mnt_userns,
+			 const struct inode *inode, kgid_t gid);
+void lock_two_inodes(struct inode *inode1, struct inode *inode2,
+		     unsigned subclass1, unsigned subclass2);
 
 /*
  * fs-writeback.c
@@ -206,3 +213,31 @@
 			 struct pipe_inode_info *opipe,
 			 loff_t *offset,
 			 size_t len, unsigned int flags);
+
+/*
+ * fs/xattr.c:
+ */
+struct xattr_name {
+	char name[XATTR_NAME_MAX + 1];
+};
+
+struct xattr_ctx {
+	/* Value of attribute */
+	union {
+		const void __user *cvalue;
+		void __user *value;
+	};
+	void *kvalue;
+	size_t size;
+	/* Attribute name */
+	struct xattr_name *kname;
+	unsigned int flags;
+};
+
+int setxattr_copy(const char __user *name, struct xattr_ctx *ctx);
+int do_setxattr(struct user_namespace *mnt_userns, struct dentry *dentry,
+		struct xattr_ctx *ctx);
+
+/*
+ * fs/attr.c
+ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ioctl.c
@@ -173,7 +173,7 @@
 
 	if (*len == 0)
 		return -EINVAL;
-	if (start > maxbytes)
+	if (start >= maxbytes)
 		return -EFBIG;
 
 	/*
@@ -920,8 +920,7 @@
 	if (!f.file)
 		return -EBADF;
 
-	/* RED-PEN how should LSM module know it's handling 32bit? */
-	error = security_file_ioctl(f.file, cmd, arg);
+	error = security_file_ioctl_compat(f.file, cmd, arg);
 	if (error)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/iomap/buffered-io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/iomap/buffered-io.c
@@ -256,8 +256,13 @@
 	unsigned poff, plen;
 	sector_t sector;
 
-	if (iomap->type == IOMAP_INLINE)
-		return min(iomap_read_inline_data(iter, page), length);
+	if (iomap->type == IOMAP_INLINE) {
+		loff_t ret = iomap_read_inline_data(iter, page);
+
+		if (ret < 0)
+			return ret;
+		return 0;
+	}
 
 	/* zero post-eof blocks as the page may be mapped */
 	iop = iomap_page_create(iter->inode, page);
@@ -370,6 +375,8 @@
 			ctx->cur_page_in_bio = false;
 		}
 		ret = iomap_readpage_iter(iter, ctx, done);
+		if (ret <= 0)
+			return ret;
 	}
 
 	return done;
@@ -518,7 +525,8 @@
 	 * write started inside the existing inode size.
 	 */
 	if (pos + len > i_size)
-		truncate_pagecache_range(inode, max(pos, i_size), pos + len);
+		truncate_pagecache_range(inode, max(pos, i_size),
+					 pos + len - 1);
 }
 
 static int
@@ -750,7 +758,7 @@
 		 * same page as we're writing to, without it being marked
 		 * up-to-date.
 		 */
-		if (unlikely(iov_iter_fault_in_readable(i, bytes))) {
+		if (unlikely(fault_in_iov_iter_readable(i, bytes))) {
 			status = -EFAULT;
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/iomap/direct-io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/iomap/direct-io.c
@@ -31,6 +31,7 @@
 	atomic_t		ref;
 	unsigned		flags;
 	int			error;
+	size_t			done_before;
 	bool			wait_for_completion;
 
 	union {
@@ -91,7 +92,6 @@
 		if (offset + ret > dio->i_size &&
 		    !(dio->flags & IOMAP_DIO_WRITE))
 			ret = dio->i_size - offset;
-		iocb->ki_pos += ret;
 	}
 
 	/*
@@ -117,15 +117,19 @@
 	}
 
 	inode_dio_end(file_inode(iocb->ki_filp));
-	/*
-	 * If this is a DSYNC write, make sure we push it to stable storage now
-	 * that we've written data.
-	 */
-	if (ret > 0 && (dio->flags & IOMAP_DIO_NEED_SYNC))
-		ret = generic_write_sync(iocb, ret);
+	if (ret > 0) {
+		iocb->ki_pos += ret;
 
+		/*
+		 * If this is a DSYNC write, make sure we push it to stable
+		 * storage now that we've written data.
+		 */
+		if (dio->flags & IOMAP_DIO_NEED_SYNC)
+			ret = generic_write_sync(iocb, ret);
+		if (ret > 0)
+			ret += dio->done_before;
+	}
 	kfree(dio);
-
 	return ret;
 }
 EXPORT_SYMBOL_GPL(iomap_dio_complete);
@@ -371,6 +375,8 @@
 	loff_t length = iov_iter_zero(iomap_length(iter), dio->submit.iter);
 
 	dio->size += length;
+	if (!length)
+		return -EFAULT;
 	return length;
 }
 
@@ -402,6 +408,8 @@
 		copied = copy_to_iter(inline_data, length, iter);
 	}
 	dio->size += copied;
+	if (!copied)
+		return -EFAULT;
 	return copied;
 }
 
@@ -446,13 +454,21 @@
  * may be pure data writes. In that case, we still need to do a full data sync
  * completion.
  *
+ * When page faults are disabled and @dio_flags includes IOMAP_DIO_PARTIAL,
+ * __iomap_dio_rw can return a partial result if it encounters a non-resident
+ * page in @iter after preparing a transfer.  In that case, the non-resident
+ * pages can be faulted in and the request resumed with @done_before set to the
+ * number of bytes previously transferred.  The request will then complete with
+ * the correct total number of bytes transferred; this is essential for
+ * completing partial requests asynchronously.
+ *
  * Returns -ENOTBLK In case of a page invalidation invalidation failure for
  * writes.  The callers needs to fall back to buffered I/O in this case.
  */
 struct iomap_dio *
 __iomap_dio_rw(struct kiocb *iocb, struct iov_iter *iter,
 		const struct iomap_ops *ops, const struct iomap_dio_ops *dops,
-		unsigned int dio_flags)
+		unsigned int dio_flags, size_t done_before)
 {
 	struct address_space *mapping = iocb->ki_filp->f_mapping;
 	struct inode *inode = file_inode(iocb->ki_filp);
@@ -482,6 +498,7 @@
 	dio->dops = dops;
 	dio->error = 0;
 	dio->flags = 0;
+	dio->done_before = done_before;
 
 	dio->submit.iter = iter;
 	dio->submit.waiter = current;
@@ -577,6 +594,12 @@
 	if (iov_iter_rw(iter) == READ && iomi.pos >= dio->i_size)
 		iov_iter_revert(iter, iomi.pos - dio->i_size);
 
+	if (ret == -EFAULT && dio->size && (dio_flags & IOMAP_DIO_PARTIAL)) {
+		if (!(iocb->ki_flags & IOCB_NOWAIT))
+			wait_for_completion = true;
+		ret = 0;
+	}
+
 	/* magic error code to fall back to buffered I/O */
 	if (ret == -ENOTBLK) {
 		wait_for_completion = true;
@@ -642,11 +665,11 @@
 ssize_t
 iomap_dio_rw(struct kiocb *iocb, struct iov_iter *iter,
 		const struct iomap_ops *ops, const struct iomap_dio_ops *dops,
-		unsigned int dio_flags)
+		unsigned int dio_flags, size_t done_before)
 {
 	struct iomap_dio *dio;
 
-	dio = __iomap_dio_rw(iocb, iter, ops, dops, dio_flags);
+	dio = __iomap_dio_rw(iocb, iter, ops, dops, dio_flags, done_before);
 	if (IS_ERR_OR_NULL(dio))
 		return PTR_ERR_OR_ZERO(dio);
 	return iomap_dio_complete(dio);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/isofs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/isofs/dir.c
@@ -147,7 +147,8 @@
 			de = tmpde;
 		}
 		/* Basic sanity check, whether name doesn't exceed dir entry */
-		if (de_len < de->name_len[0] +
+		if (de_len < sizeof(struct iso_directory_record) ||
+		    de_len < de->name_len[0] +
 					sizeof(struct iso_directory_record)) {
 			printk(KERN_NOTICE "iso9660: Corrupted directory entry"
 			       " in block %lu of inode %lu\n", block,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/isofs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/isofs/inode.c
@@ -908,8 +908,22 @@
 	 * we then decide whether to use the Joliet descriptor.
 	 */
 	inode = isofs_iget(s, sbi->s_firstdatazone, 0);
-	if (IS_ERR(inode))
-		goto out_no_root;
+
+	/*
+	 * Fix for broken CDs with a corrupt root inode but a correct Joliet
+	 * root directory.
+	 */
+	if (IS_ERR(inode)) {
+		if (joliet_level && sbi->s_firstdatazone != first_data_zone) {
+			printk(KERN_NOTICE
+			       "ISOFS: root inode is unusable. "
+			       "Disabling Rock Ridge and switching to Joliet.");
+			sbi->s_rock = 0;
+			inode = NULL;
+		} else {
+			goto out_no_root;
+		}
+	}
 
 	/*
 	 * Fix for broken CDs with Rock Ridge and empty ISO root directory but
@@ -1322,6 +1336,8 @@
 
 	de = (struct iso_directory_record *) (bh->b_data + offset);
 	de_len = *(unsigned char *) de;
+	if (de_len < sizeof(struct iso_directory_record))
+		goto fail;
 
 	if (offset + de_len > bufsize) {
 		int frag1 = bufsize - offset;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jbd2/checkpoint.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jbd2/checkpoint.c
@@ -27,7 +27,7 @@
  *
  * Called with j_list_lock held.
  */
-static inline void __buffer_unlink_first(struct journal_head *jh)
+static inline void __buffer_unlink(struct journal_head *jh)
 {
 	transaction_t *transaction = jh->b_cp_transaction;
 
@@ -41,45 +41,6 @@
 }
 
 /*
- * Unlink a buffer from a transaction checkpoint(io) list.
- *
- * Called with j_list_lock held.
- */
-static inline void __buffer_unlink(struct journal_head *jh)
-{
-	transaction_t *transaction = jh->b_cp_transaction;
-
-	__buffer_unlink_first(jh);
-	if (transaction->t_checkpoint_io_list == jh) {
-		transaction->t_checkpoint_io_list = jh->b_cpnext;
-		if (transaction->t_checkpoint_io_list == jh)
-			transaction->t_checkpoint_io_list = NULL;
-	}
-}
-
-/*
- * Move a buffer from the checkpoint list to the checkpoint io list
- *
- * Called with j_list_lock held
- */
-static inline void __buffer_relink_io(struct journal_head *jh)
-{
-	transaction_t *transaction = jh->b_cp_transaction;
-
-	__buffer_unlink_first(jh);
-
-	if (!transaction->t_checkpoint_io_list) {
-		jh->b_cpnext = jh->b_cpprev = jh;
-	} else {
-		jh->b_cpnext = transaction->t_checkpoint_io_list;
-		jh->b_cpprev = transaction->t_checkpoint_io_list->b_cpprev;
-		jh->b_cpprev->b_cpnext = jh;
-		jh->b_cpnext->b_cpprev = jh;
-	}
-	transaction->t_checkpoint_io_list = jh;
-}
-
-/*
  * Check a checkpoint buffer could be release or not.
  *
  * Requires j_list_lock
@@ -130,17 +91,23 @@
 		if (space_left < nblocks) {
 			int chkpt = journal->j_checkpoint_transactions != NULL;
 			tid_t tid = 0;
+			bool has_transaction = false;
 
-			if (journal->j_committing_transaction)
+			if (journal->j_committing_transaction) {
 				tid = journal->j_committing_transaction->t_tid;
+				has_transaction = true;
+			}
 			spin_unlock(&journal->j_list_lock);
 			write_unlock(&journal->j_state_lock);
 			if (chkpt) {
 				jbd2_log_do_checkpoint(journal);
-			} else if (jbd2_cleanup_journal_tail(journal) == 0) {
-				/* We were able to recover space; yay! */
+			} else if (jbd2_cleanup_journal_tail(journal) <= 0) {
+				/*
+				 * We were able to recover space or the
+				 * journal was aborted due to an error.
+				 */
 				;
-			} else if (tid) {
+			} else if (has_transaction) {
 				/*
 				 * jbd2_journal_commit_transaction() may want
 				 * to take the checkpoint_mutex if JBD2_FLUSHED
@@ -183,6 +150,7 @@
 		struct buffer_head *bh = journal->j_chkpt_bhs[i];
 		BUFFER_TRACE(bh, "brelse");
 		__brelse(bh);
+		journal->j_chkpt_bhs[i] = NULL;
 	}
 	*batch_count = 0;
 }
@@ -203,7 +171,7 @@
 	tid_t			this_tid;
 	int			result, batch_count = 0;
 
-	jbd_debug(1, "Start checkpoint\n");
+	jbd2_debug(1, "Start checkpoint\n");
 
 	/*
 	 * First thing: if there are any transactions in the log which
@@ -212,7 +180,7 @@
 	 */
 	result = jbd2_cleanup_journal_tail(journal);
 	trace_jbd2_checkpoint(journal, result);
-	jbd_debug(1, "cleanup_journal_tail returned %d\n", result);
+	jbd2_debug(1, "cleanup_journal_tail returned %d\n", result);
 	if (result <= 0)
 		return result;
 
@@ -242,15 +210,6 @@
 		jh = transaction->t_checkpoint_list;
 		bh = jh2bh(jh);
 
-		if (buffer_locked(bh)) {
-			get_bh(bh);
-			spin_unlock(&journal->j_list_lock);
-			wait_on_buffer(bh);
-			/* the journal_head may have gone by now */
-			BUFFER_TRACE(bh, "brelse");
-			__brelse(bh);
-			goto retry;
-		}
 		if (jh->b_transaction != NULL) {
 			transaction_t *t = jh->b_transaction;
 			tid_t tid = t->t_tid;
@@ -285,30 +244,50 @@
 			spin_lock(&journal->j_list_lock);
 			goto restart;
 		}
-		if (!buffer_dirty(bh)) {
+		if (!trylock_buffer(bh)) {
+			/*
+			 * The buffer is locked, it may be writing back, or
+			 * flushing out in the last couple of cycles, or
+			 * re-adding into a new transaction, need to check
+			 * it again until it's unlocked.
+			 */
+			get_bh(bh);
+			spin_unlock(&journal->j_list_lock);
+			wait_on_buffer(bh);
+			/* the journal_head may have gone by now */
+			BUFFER_TRACE(bh, "brelse");
+			__brelse(bh);
+			goto retry;
+		} else if (!buffer_dirty(bh)) {
+			unlock_buffer(bh);
 			BUFFER_TRACE(bh, "remove from checkpoint");
-			if (__jbd2_journal_remove_checkpoint(jh))
-				/* The transaction was released; we're done */
+			/*
+			 * If the transaction was released or the checkpoint
+			 * list was empty, we're done.
+			 */
+			if (__jbd2_journal_remove_checkpoint(jh) ||
+			    !transaction->t_checkpoint_list)
 				goto out;
-			continue;
+		} else {
+			unlock_buffer(bh);
+			/*
+			 * We are about to write the buffer, it could be
+			 * raced by some other transaction shrink or buffer
+			 * re-log logic once we release the j_list_lock,
+			 * leave it on the checkpoint list and check status
+			 * again to make sure it's clean.
+			 */
+			BUFFER_TRACE(bh, "queue");
+			get_bh(bh);
+			J_ASSERT_BH(bh, !buffer_jwrite(bh));
+			journal->j_chkpt_bhs[batch_count++] = bh;
+			transaction->t_chp_stats.cs_written++;
+			transaction->t_checkpoint_list = jh->b_cpnext;
 		}
-		/*
-		 * Important: we are about to write the buffer, and
-		 * possibly block, while still holding the journal
-		 * lock.  We cannot afford to let the transaction
-		 * logic start messing around with this buffer before
-		 * we write it to disk, as that would break
-		 * recoverability.
-		 */
-		BUFFER_TRACE(bh, "queue");
-		get_bh(bh);
-		J_ASSERT_BH(bh, !buffer_jwrite(bh));
-		journal->j_chkpt_bhs[batch_count++] = bh;
-		__buffer_relink_io(jh);
-		transaction->t_chp_stats.cs_written++;
+
 		if ((batch_count == JBD2_NR_BATCH) ||
-		    need_resched() ||
-		    spin_needbreak(&journal->j_list_lock))
+		    need_resched() || spin_needbreak(&journal->j_list_lock) ||
+		    jh2bh(transaction->t_checkpoint_list) == journal->j_chkpt_bhs[0])
 			goto unlock_and_flush;
 	}
 
@@ -322,38 +301,6 @@
 			goto restart;
 	}
 
-	/*
-	 * Now we issued all of the transaction's buffers, let's deal
-	 * with the buffers that are out for I/O.
-	 */
-restart2:
-	/* Did somebody clean up the transaction in the meanwhile? */
-	if (journal->j_checkpoint_transactions != transaction ||
-	    transaction->t_tid != this_tid)
-		goto out;
-
-	while (transaction->t_checkpoint_io_list) {
-		jh = transaction->t_checkpoint_io_list;
-		bh = jh2bh(jh);
-		if (buffer_locked(bh)) {
-			get_bh(bh);
-			spin_unlock(&journal->j_list_lock);
-			wait_on_buffer(bh);
-			/* the journal_head may have gone by now */
-			BUFFER_TRACE(bh, "brelse");
-			__brelse(bh);
-			spin_lock(&journal->j_list_lock);
-			goto restart2;
-		}
-
-		/*
-		 * Now in whatever state the buffer currently is, we
-		 * know that it has been written out and so we can
-		 * drop it from the list
-		 */
-		if (__jbd2_journal_remove_checkpoint(jh))
-			break;
-	}
 out:
 	spin_unlock(&journal->j_list_lock);
 	result = jbd2_cleanup_journal_tail(journal);
@@ -408,50 +355,12 @@
 
 /* Checkpoint list management */
 
-/*
- * journal_clean_one_cp_list
- *
- * Find all the written-back checkpoint buffers in the given list and
- * release them. If 'destroy' is set, clean all buffers unconditionally.
- *
- * Called with j_list_lock held.
- * Returns 1 if we freed the transaction, 0 otherwise.
- */
-static int journal_clean_one_cp_list(struct journal_head *jh, bool destroy)
-{
-	struct journal_head *last_jh;
-	struct journal_head *next_jh = jh;
-
-	if (!jh)
-		return 0;
-
-	last_jh = jh->b_cpprev;
-	do {
-		jh = next_jh;
-		next_jh = jh->b_cpnext;
-
-		if (!destroy && __cp_buffer_busy(jh))
-			return 0;
-
-		if (__jbd2_journal_remove_checkpoint(jh))
-			return 1;
-		/*
-		 * This function only frees up some memory
-		 * if possible so we dont have an obligation
-		 * to finish processing. Bail out if preemption
-		 * requested:
-		 */
-		if (need_resched())
-			return 0;
-	} while (jh != last_jh);
-
-	return 0;
-}
+enum shrink_type {SHRINK_DESTROY, SHRINK_BUSY_STOP, SHRINK_BUSY_SKIP};
 
 /*
  * journal_shrink_one_cp_list
  *
- * Find 'nr_to_scan' written-back checkpoint buffers in the given list
+ * Find all the written-back checkpoint buffers in the given list
  * and try to release them. If the whole transaction is released, set
  * the 'released' parameter. Return the number of released checkpointed
  * buffers.
@@ -459,7 +368,7 @@
  * Called with j_list_lock held.
  */
 static unsigned long journal_shrink_one_cp_list(struct journal_head *jh,
-						unsigned long *nr_to_scan,
+						enum shrink_type type,
 						bool *released)
 {
 	struct journal_head *last_jh;
@@ -467,7 +376,8 @@
 	unsigned long nr_freed = 0;
 	int ret;
 
-	if (!jh || *nr_to_scan == 0)
+	*released = false;
+	if (!jh)
 		return 0;
 
 	last_jh = jh->b_cpprev;
@@ -475,12 +385,18 @@
 		jh = next_jh;
 		next_jh = jh->b_cpnext;
 
-		(*nr_to_scan)--;
-		if (__cp_buffer_busy(jh))
-			continue;
+		if (type == SHRINK_DESTROY) {
+			ret = __jbd2_journal_remove_checkpoint(jh);
+		} else {
+			ret = jbd2_journal_try_remove_checkpoint(jh);
+			if (ret < 0) {
+				if (type == SHRINK_BUSY_SKIP)
+					continue;
+				break;
+			}
+		}
 
 		nr_freed++;
-		ret = __jbd2_journal_remove_checkpoint(jh);
 		if (ret) {
 			*released = true;
 			break;
@@ -488,7 +404,7 @@
 
 		if (need_resched())
 			break;
-	} while (jh != last_jh && *nr_to_scan);
+	} while (jh != last_jh);
 
 	return nr_freed;
 }
@@ -506,11 +422,12 @@
 						  unsigned long *nr_to_scan)
 {
 	transaction_t *transaction, *last_transaction, *next_transaction;
-	bool released;
+	bool __maybe_unused released;
 	tid_t first_tid = 0, last_tid = 0, next_tid = 0;
 	tid_t tid = 0;
 	unsigned long nr_freed = 0;
-	unsigned long nr_scanned = *nr_to_scan;
+	unsigned long freed;
+	bool first_set = false;
 
 again:
 	spin_lock(&journal->j_list_lock);
@@ -530,8 +447,10 @@
 	else
 		transaction = journal->j_checkpoint_transactions;
 
-	if (!first_tid)
+	if (!first_set) {
 		first_tid = transaction->t_tid;
+		first_set = true;
+	}
 	last_transaction = journal->j_checkpoint_transactions->t_cpprev;
 	next_transaction = transaction;
 	last_tid = last_transaction->t_tid;
@@ -539,19 +458,11 @@
 		transaction = next_transaction;
 		next_transaction = transaction->t_cpnext;
 		tid = transaction->t_tid;
-		released = false;
 
-		nr_freed += journal_shrink_one_cp_list(transaction->t_checkpoint_list,
-						       nr_to_scan, &released);
-		if (*nr_to_scan == 0)
-			break;
-		if (need_resched() || spin_needbreak(&journal->j_list_lock))
-			break;
-		if (released)
-			continue;
-
-		nr_freed += journal_shrink_one_cp_list(transaction->t_checkpoint_io_list,
-						       nr_to_scan, &released);
+		freed = journal_shrink_one_cp_list(transaction->t_checkpoint_list,
+						   SHRINK_BUSY_SKIP, &released);
+		nr_freed += freed;
+		(*nr_to_scan) -= min(*nr_to_scan, freed);
 		if (*nr_to_scan == 0)
 			break;
 		if (need_resched() || spin_needbreak(&journal->j_list_lock))
@@ -569,12 +480,11 @@
 	spin_unlock(&journal->j_list_lock);
 	cond_resched();
 
-	if (*nr_to_scan && next_tid)
+	if (*nr_to_scan && journal->j_shrink_transaction)
 		goto again;
 out:
-	nr_scanned -= *nr_to_scan;
 	trace_jbd2_shrink_checkpoint_list(journal, first_tid, tid, last_tid,
-					  nr_freed, nr_scanned, next_tid);
+					  nr_freed, next_tid);
 
 	return nr_freed;
 }
@@ -590,19 +500,21 @@
 void __jbd2_journal_clean_checkpoint_list(journal_t *journal, bool destroy)
 {
 	transaction_t *transaction, *last_transaction, *next_transaction;
-	int ret;
+	enum shrink_type type;
+	bool released;
 
 	transaction = journal->j_checkpoint_transactions;
 	if (!transaction)
 		return;
 
+	type = destroy ? SHRINK_DESTROY : SHRINK_BUSY_STOP;
 	last_transaction = transaction->t_cpprev;
 	next_transaction = transaction;
 	do {
 		transaction = next_transaction;
 		next_transaction = transaction->t_cpnext;
-		ret = journal_clean_one_cp_list(transaction->t_checkpoint_list,
-						destroy);
+		journal_shrink_one_cp_list(transaction->t_checkpoint_list,
+					   type, &released);
 		/*
 		 * This function only frees up some memory if possible so we
 		 * dont have an obligation to finish processing. Bail out if
@@ -610,23 +522,12 @@
 		 */
 		if (need_resched())
 			return;
-		if (ret)
-			continue;
-		/*
-		 * It is essential that we are as careful as in the case of
-		 * t_checkpoint_list with removing the buffer from the list as
-		 * we can possibly see not yet submitted buffers on io_list
-		 */
-		ret = journal_clean_one_cp_list(transaction->
-				t_checkpoint_io_list, destroy);
-		if (need_resched())
-			return;
 		/*
 		 * Stop scanning if we couldn't free the transaction. This
 		 * avoids pointless scanning of transactions which still
 		 * weren't checkpointed.
 		 */
-		if (!ret)
+		if (!released)
 			return;
 	} while (transaction != last_transaction);
 }
@@ -705,7 +606,7 @@
 	jbd2_journal_put_journal_head(jh);
 
 	/* Is this transaction empty? */
-	if (transaction->t_checkpoint_list || transaction->t_checkpoint_io_list)
+	if (transaction->t_checkpoint_list)
 		return 0;
 
 	/*
@@ -737,6 +638,36 @@
 }
 
 /*
+ * Check the checkpoint buffer and try to remove it from the checkpoint
+ * list if it's clean. Returns -EBUSY if it is not clean, returns 1 if
+ * it frees the transaction, 0 otherwise.
+ *
+ * This function is called with j_list_lock held.
+ */
+int jbd2_journal_try_remove_checkpoint(struct journal_head *jh)
+{
+	struct buffer_head *bh = jh2bh(jh);
+
+	if (jh->b_transaction)
+		return -EBUSY;
+	if (!trylock_buffer(bh))
+		return -EBUSY;
+	if (buffer_dirty(bh)) {
+		unlock_buffer(bh);
+		return -EBUSY;
+	}
+	unlock_buffer(bh);
+
+	/*
+	 * Buffer is clean and the IO has finished (we held the buffer
+	 * lock) so the checkpoint is done. We can safely remove the
+	 * buffer from this transaction.
+	 */
+	JBUFFER_TRACE(jh, "remove from checkpoint list");
+	return __jbd2_journal_remove_checkpoint(jh);
+}
+
+/*
  * journal_insert_checkpoint: put a committed buffer onto a checkpoint
  * list so that we know when it is safe to clean the transaction out of
  * the log.
@@ -797,12 +728,11 @@
 	J_ASSERT(transaction->t_forget == NULL);
 	J_ASSERT(transaction->t_shadow_list == NULL);
 	J_ASSERT(transaction->t_checkpoint_list == NULL);
-	J_ASSERT(transaction->t_checkpoint_io_list == NULL);
 	J_ASSERT(atomic_read(&transaction->t_updates) == 0);
 	J_ASSERT(journal->j_committing_transaction != transaction);
 	J_ASSERT(journal->j_running_transaction != transaction);
 
 	trace_jbd2_drop_transaction(journal, transaction);
 
-	jbd_debug(1, "Dropping transaction %d, all done\n", transaction->t_tid);
+	jbd2_debug(1, "Dropping transaction %d, all done\n", transaction->t_tid);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jbd2/commit.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jbd2/commit.c
@@ -300,6 +300,7 @@
 			if (!ret)
 				ret = err;
 		}
+		cond_resched();
 		spin_lock(&journal->j_list_lock);
 		jinode->i_flags &= ~JI_COMMIT_RUNNING;
 		smp_mb();
@@ -419,7 +420,7 @@
 
 	/* Do we need to erase the effects of a prior jbd2_journal_flush? */
 	if (journal->j_flags & JBD2_FLUSHED) {
-		jbd_debug(3, "super block updated\n");
+		jbd2_debug(3, "super block updated\n");
 		mutex_lock_io(&journal->j_checkpoint_mutex);
 		/*
 		 * We hold j_checkpoint_mutex so tail cannot change under us.
@@ -433,7 +434,7 @@
 						REQ_SYNC);
 		mutex_unlock(&journal->j_checkpoint_mutex);
 	} else {
-		jbd_debug(3, "superblock not updated\n");
+		jbd2_debug(3, "superblock not updated\n");
 	}
 
 	J_ASSERT(journal->j_running_transaction != NULL);
@@ -465,7 +466,7 @@
 	commit_transaction = journal->j_running_transaction;
 
 	trace_jbd2_start_commit(journal, commit_transaction);
-	jbd_debug(1, "JBD2: starting commit of transaction %d\n",
+	jbd2_debug(1, "JBD2: starting commit of transaction %d\n",
 			commit_transaction->t_tid);
 
 	write_lock(&journal->j_state_lock);
@@ -484,24 +485,10 @@
 	stats.run.rs_running = jbd2_time_diff(commit_transaction->t_start,
 					      stats.run.rs_locked);
 
-	spin_lock(&commit_transaction->t_handle_lock);
-	while (atomic_read(&commit_transaction->t_updates)) {
-		DEFINE_WAIT(wait);
+	// waits for any t_updates to finish
+	jbd2_journal_wait_updates(journal);
 
-		prepare_to_wait(&journal->j_wait_updates, &wait,
-					TASK_UNINTERRUPTIBLE);
-		if (atomic_read(&commit_transaction->t_updates)) {
-			spin_unlock(&commit_transaction->t_handle_lock);
-			write_unlock(&journal->j_state_lock);
-			schedule();
-			write_lock(&journal->j_state_lock);
-			spin_lock(&commit_transaction->t_handle_lock);
-		}
-		finish_wait(&journal->j_wait_updates, &wait);
-	}
-	spin_unlock(&commit_transaction->t_handle_lock);
 	commit_transaction->t_state = T_SWITCH;
-	write_unlock(&journal->j_state_lock);
 
 	J_ASSERT (atomic_read(&commit_transaction->t_outstanding_credits) <=
 			journal->j_max_transaction_buffers);
@@ -521,6 +508,8 @@
 	 * has reserved.  This is consistent with the existing behaviour
 	 * that multiple jbd2_journal_get_write_access() calls to the same
 	 * buffer are perfectly permissible.
+	 * We use journal->j_state_lock here to serialize processing of
+	 * t_reserved_list with eviction of buffers from journal_unmap_buffer().
 	 */
 	while (commit_transaction->t_reserved_list) {
 		jh = commit_transaction->t_reserved_list;
@@ -540,6 +529,7 @@
 		jbd2_journal_refile_buffer(journal, jh);
 	}
 
+	write_unlock(&journal->j_state_lock);
 	/*
 	 * Now try to drop any written-back buffers from the journal's
 	 * checkpoint lists.  We do this *before* commit because it potentially
@@ -549,7 +539,7 @@
 	__jbd2_journal_clean_checkpoint_list(journal, false);
 	spin_unlock(&journal->j_list_lock);
 
-	jbd_debug(3, "JBD2: commit phase 1\n");
+	jbd2_debug(3, "JBD2: commit phase 1\n");
 
 	/*
 	 * Clear revoked flag to reflect there is no revoked buffers
@@ -562,13 +552,13 @@
 	 */
 	jbd2_journal_switch_revoke_table(journal);
 
+	write_lock(&journal->j_state_lock);
 	/*
 	 * Reserved credits cannot be claimed anymore, free them
 	 */
 	atomic_sub(atomic_read(&journal->j_reserved_credits),
 		   &commit_transaction->t_outstanding_credits);
 
-	write_lock(&journal->j_state_lock);
 	trace_jbd2_commit_flushing(journal, commit_transaction);
 	stats.run.rs_flushing = jiffies;
 	stats.run.rs_locked = jbd2_time_diff(stats.run.rs_locked,
@@ -579,10 +569,10 @@
 	journal->j_running_transaction = NULL;
 	start_time = ktime_get();
 	commit_transaction->t_log_start = journal->j_head;
-	wake_up(&journal->j_wait_transaction_locked);
+	wake_up_all(&journal->j_wait_transaction_locked);
 	write_unlock(&journal->j_state_lock);
 
-	jbd_debug(3, "JBD2: commit phase 2a\n");
+	jbd2_debug(3, "JBD2: commit phase 2a\n");
 
 	/*
 	 * Now start flushing things to disk, in the order they appear
@@ -595,7 +585,7 @@
 	blk_start_plug(&plug);
 	jbd2_journal_write_revoke_records(commit_transaction, &log_bufs);
 
-	jbd_debug(3, "JBD2: commit phase 2b\n");
+	jbd2_debug(3, "JBD2: commit phase 2b\n");
 
 	/*
 	 * Way to go: we have now written out all of the data for a
@@ -651,7 +641,7 @@
 		if (!descriptor) {
 			J_ASSERT (bufs == 0);
 
-			jbd_debug(4, "JBD2: get descriptor\n");
+			jbd2_debug(4, "JBD2: get descriptor\n");
 
 			descriptor = jbd2_journal_get_descriptor_buffer(
 							commit_transaction,
@@ -661,7 +651,7 @@
 				continue;
 			}
 
-			jbd_debug(4, "JBD2: got buffer %llu (%p)\n",
+			jbd2_debug(4, "JBD2: got buffer %llu (%p)\n",
 				(unsigned long long)descriptor->b_blocknr,
 				descriptor->b_data);
 			tagp = &descriptor->b_data[sizeof(journal_header_t)];
@@ -746,7 +736,7 @@
 		    commit_transaction->t_buffers == NULL ||
 		    space_left < tag_bytes + 16 + csum_size) {
 
-			jbd_debug(4, "JBD2: Submit %d IOs\n", bufs);
+			jbd2_debug(4, "JBD2: Submit %d IOs\n", bufs);
 
 			/* Write an end-of-descriptor marker before
                            submitting the IOs.  "tag" still points to
@@ -810,19 +800,19 @@
 		if (first_block < journal->j_tail)
 			freed += journal->j_last - journal->j_first;
 		/* Update tail only if we free significant amount of space */
-		if (freed < jbd2_journal_get_max_txn_bufs(journal))
+		if (freed < journal->j_max_transaction_buffers)
 			update_tail = 0;
 	}
 	J_ASSERT(commit_transaction->t_state == T_COMMIT);
 	commit_transaction->t_state = T_COMMIT_DFLUSH;
 	write_unlock(&journal->j_state_lock);
 
-	/* 
+	/*
 	 * If the journal is not located on the file system device,
 	 * then we must flush the file system device before we issue
-	 * the commit record
+	 * the commit record and update the journal tail sequence.
 	 */
-	if (commit_transaction->t_need_data_flush &&
+	if ((commit_transaction->t_need_data_flush || update_tail) &&
 	    (journal->j_fs_dev != journal->j_dev) &&
 	    (journal->j_flags & JBD2_BARRIER))
 		blkdev_issue_flush(journal->j_fs_dev);
@@ -848,7 +838,7 @@
 	   so we incur less scheduling load.
 	*/
 
-	jbd_debug(3, "JBD2: commit phase 3\n");
+	jbd2_debug(3, "JBD2: commit phase 3\n");
 
 	while (!list_empty(&io_bufs)) {
 		struct buffer_head *bh = list_entry(io_bufs.prev,
@@ -891,7 +881,7 @@
 
 	J_ASSERT (commit_transaction->t_shadow_list == NULL);
 
-	jbd_debug(3, "JBD2: commit phase 4\n");
+	jbd2_debug(3, "JBD2: commit phase 4\n");
 
 	/* Here we wait for the revoke record and descriptor record buffers */
 	while (!list_empty(&log_bufs)) {
@@ -915,7 +905,7 @@
 	if (err)
 		jbd2_journal_abort(journal, err);
 
-	jbd_debug(3, "JBD2: commit phase 5\n");
+	jbd2_debug(3, "JBD2: commit phase 5\n");
 	write_lock(&journal->j_state_lock);
 	J_ASSERT(commit_transaction->t_state == T_COMMIT_DFLUSH);
 	commit_transaction->t_state = T_COMMIT_JFLUSH;
@@ -954,7 +944,7 @@
            transaction can be removed from any checkpoint list it was on
            before. */
 
-	jbd_debug(3, "JBD2: commit phase 6\n");
+	jbd2_debug(3, "JBD2: commit phase 6\n");
 
 	J_ASSERT(list_empty(&commit_transaction->t_inode_list));
 	J_ASSERT(commit_transaction->t_buffers == NULL);
@@ -1131,7 +1121,7 @@
 
 	/* Done with this transaction! */
 
-	jbd_debug(3, "JBD2: commit phase 7\n");
+	jbd2_debug(3, "JBD2: commit phase 7\n");
 
 	J_ASSERT(commit_transaction->t_state == T_COMMIT_JFLUSH);
 
@@ -1170,10 +1160,10 @@
 	if (journal->j_commit_callback)
 		journal->j_commit_callback(journal, commit_transaction);
 	if (journal->j_fc_cleanup_callback)
-		journal->j_fc_cleanup_callback(journal, 1);
+		journal->j_fc_cleanup_callback(journal, 1, commit_transaction->t_tid);
 
 	trace_jbd2_end_commit(journal, commit_transaction);
-	jbd_debug(1, "JBD2: commit %d complete, head %d\n",
+	jbd2_debug(1, "JBD2: commit %d complete, head %d\n",
 		  journal->j_commit_sequence, journal->j_tail_sequence);
 
 	write_lock(&journal->j_state_lock);
@@ -1182,8 +1172,7 @@
 	spin_lock(&journal->j_list_lock);
 	commit_transaction->t_state = T_FINISHED;
 	/* Check if the transaction can be dropped now that we are finished */
-	if (commit_transaction->t_checkpoint_list == NULL &&
-	    commit_transaction->t_checkpoint_io_list == NULL) {
+	if (commit_transaction->t_checkpoint_list == NULL) {
 		__jbd2_journal_drop_transaction(journal, commit_transaction);
 		jbd2_journal_free_transaction(commit_transaction);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jbd2/journal.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jbd2/journal.c
@@ -203,11 +203,11 @@
 	if (journal->j_flags & JBD2_UNMOUNT)
 		goto end_loop;
 
-	jbd_debug(1, "commit_sequence=%u, commit_request=%u\n",
+	jbd2_debug(1, "commit_sequence=%u, commit_request=%u\n",
 		journal->j_commit_sequence, journal->j_commit_request);
 
 	if (journal->j_commit_sequence != journal->j_commit_request) {
-		jbd_debug(1, "OK, requests differ\n");
+		jbd2_debug(1, "OK, requests differ\n");
 		write_unlock(&journal->j_state_lock);
 		del_timer_sync(&journal->j_commit_timer);
 		jbd2_journal_commit_transaction(journal);
@@ -222,7 +222,7 @@
 		 * good idea, because that depends on threads that may
 		 * be already stopped.
 		 */
-		jbd_debug(1, "Now suspending kjournald2\n");
+		jbd2_debug(1, "Now suspending kjournald2\n");
 		write_unlock(&journal->j_state_lock);
 		try_to_freeze();
 		write_lock(&journal->j_state_lock);
@@ -252,7 +252,7 @@
 		finish_wait(&journal->j_wait_commit, &wait);
 	}
 
-	jbd_debug(1, "kjournald2 wakes\n");
+	jbd2_debug(1, "kjournald2 wakes\n");
 
 	/*
 	 * Were we woken up by a commit wakeup event?
@@ -260,7 +260,7 @@
 	transaction = journal->j_running_transaction;
 	if (transaction && time_after_eq(jiffies, transaction->t_expires)) {
 		journal->j_commit_request = transaction->t_tid;
-		jbd_debug(1, "woke because of timeout\n");
+		jbd2_debug(1, "woke because of timeout\n");
 	}
 	goto loop;
 
@@ -268,7 +268,7 @@
 	del_timer_sync(&journal->j_commit_timer);
 	journal->j_task = NULL;
 	wake_up(&journal->j_wait_done_commit);
-	jbd_debug(1, "Journal thread exiting.\n");
+	jbd2_debug(1, "Journal thread exiting.\n");
 	write_unlock(&journal->j_state_lock);
 	return 0;
 }
@@ -412,6 +412,7 @@
 		tmp = jbd2_alloc(bh_in->b_size, GFP_NOFS);
 		if (!tmp) {
 			brelse(new_bh);
+			free_buffer_head(new_bh);
 			return -ENOMEM;
 		}
 		spin_lock(&jh_in->b_state_lock);
@@ -500,7 +501,7 @@
 		 */
 
 		journal->j_commit_request = target;
-		jbd_debug(1, "JBD2: requesting commit %u/%u\n",
+		jbd2_debug(1, "JBD2: requesting commit %u/%u\n",
 			  journal->j_commit_request,
 			  journal->j_commit_sequence);
 		journal->j_running_transaction->t_requested = jiffies;
@@ -705,7 +706,7 @@
 	}
 #endif
 	while (tid_gt(tid, journal->j_commit_sequence)) {
-		jbd_debug(1, "JBD2: want %u, j_commit_sequence=%u\n",
+		jbd2_debug(1, "JBD2: want %u, j_commit_sequence=%u\n",
 				  tid, journal->j_commit_sequence);
 		read_unlock(&journal->j_state_lock);
 		wake_up(&journal->j_wait_commit);
@@ -739,7 +740,7 @@
 		return -EINVAL;
 
 	write_lock(&journal->j_state_lock);
-	if (tid <= journal->j_commit_sequence) {
+	if (tid_geq(journal->j_commit_sequence, tid)) {
 		write_unlock(&journal->j_state_lock);
 		return -EALREADY;
 	}
@@ -757,6 +758,7 @@
 	}
 	journal->j_flags |= JBD2_FAST_COMMIT_ONGOING;
 	write_unlock(&journal->j_state_lock);
+	jbd2_journal_lock_updates(journal);
 
 	return 0;
 }
@@ -769,7 +771,8 @@
 static int __jbd2_fc_end_commit(journal_t *journal, tid_t tid, bool fallback)
 {
 	if (journal->j_fc_cleanup_callback)
-		journal->j_fc_cleanup_callback(journal, 0);
+		journal->j_fc_cleanup_callback(journal, 0, tid);
+	jbd2_journal_unlock_updates(journal);
 	write_lock(&journal->j_state_lock);
 	journal->j_flags &= ~JBD2_FAST_COMMIT_ONGOING;
 	if (fallback)
@@ -924,10 +927,16 @@
 	for (i = j_fc_off - 1; i >= j_fc_off - num_blks; i--) {
 		bh = journal->j_fc_wbuf[i];
 		wait_on_buffer(bh);
+		/*
+		 * Update j_fc_off so jbd2_fc_release_bufs can release remain
+		 * buffer head.
+		 */
+		if (unlikely(!buffer_uptodate(bh))) {
+			journal->j_fc_off = i + 1;
+			return -EIO;
+		}
 		put_bh(bh);
 		journal->j_fc_wbuf[i] = NULL;
-		if (unlikely(!buffer_uptodate(bh)))
-			return -EIO;
 	}
 
 	return 0;
@@ -1115,7 +1124,7 @@
 		freed += journal->j_last - journal->j_first;
 
 	trace_jbd2_update_log_tail(journal, tid, block, freed);
-	jbd_debug(1,
+	jbd2_debug(1,
 		  "Cleaning journal tail from %u to %u (offset %lu), "
 		  "freeing %lu\n",
 		  journal->j_tail_sequence, tid, block, freed);
@@ -1490,7 +1499,7 @@
 		return NULL;
 	}
 
-	jbd_debug(1, "JBD2: inode %s/%ld, size %lld, bits %d, blksize %ld\n",
+	jbd2_debug(1, "JBD2: inode %s/%ld, size %lld, bits %d, blksize %ld\n",
 		  inode->i_sb->s_id, inode->i_ino, (long long) inode->i_size,
 		  inode->i_sb->s_blocksize_bits, inode->i_sb->s_blocksize);
 
@@ -1521,6 +1530,11 @@
 	journal->j_sb_buffer = NULL;
 }
 
+static int jbd2_journal_get_max_txn_bufs(journal_t *journal)
+{
+	return (journal->j_total_len - journal->j_fc_wbufsize) / 4;
+}
+
 /*
  * Given a journal_t structure, initialise the various fields for
  * startup of a new journaling session.  We use this both when creating
@@ -1569,7 +1583,7 @@
 	 * attempting a write to a potential-readonly device.
 	 */
 	if (sb->s_start == 0) {
-		jbd_debug(1, "JBD2: Skipping superblock update on recovered sb "
+		jbd2_debug(1, "JBD2: Skipping superblock update on recovered sb "
 			"(start %ld, seq %u, errno %d)\n",
 			journal->j_tail, journal->j_tail_sequence,
 			journal->j_errno);
@@ -1608,9 +1622,11 @@
 		return -EIO;
 	}
 
-	trace_jbd2_write_superblock(journal, write_flags);
 	if (!(journal->j_flags & JBD2_BARRIER))
 		write_flags &= ~(REQ_FUA | REQ_PREFLUSH);
+
+	trace_jbd2_write_superblock(journal, write_flags);
+
 	if (buffer_write_io_error(bh)) {
 		/*
 		 * Oh, dear.  A previous attempt to write the journal
@@ -1672,7 +1688,7 @@
 	}
 
 	BUG_ON(!mutex_is_locked(&journal->j_checkpoint_mutex));
-	jbd_debug(1, "JBD2: updating superblock (start %lu, seq %u)\n",
+	jbd2_debug(1, "JBD2: updating superblock (start %lu, seq %u)\n",
 		  tail_block, tail_tid);
 
 	lock_buffer(journal->j_sb_buffer);
@@ -1713,7 +1729,7 @@
 		return;
 	}
 
-	jbd_debug(1, "JBD2: Marking journal as empty (seq %u)\n",
+	jbd2_debug(1, "JBD2: Marking journal as empty (seq %u)\n",
 		  journal->j_tail_sequence);
 
 	sb->s_sequence = cpu_to_be32(journal->j_tail_sequence);
@@ -1859,7 +1875,7 @@
 	errcode = journal->j_errno;
 	if (errcode == -ESHUTDOWN)
 		errcode = 0;
-	jbd_debug(1, "JBD2: updating superblock error (errno %d)\n", errcode);
+	jbd2_debug(1, "JBD2: updating superblock error (errno %d)\n", errcode);
 	sb->s_errno    = cpu_to_be32(errcode);
 
 	jbd2_write_superblock(journal, REQ_SYNC | REQ_FUA);
@@ -2331,7 +2347,7 @@
 	    compat & JBD2_FEATURE_COMPAT_CHECKSUM)
 		compat &= ~JBD2_FEATURE_COMPAT_CHECKSUM;
 
-	jbd_debug(1, "Setting new features 0x%lx/0x%lx/0x%lx\n",
+	jbd2_debug(1, "Setting new features 0x%lx/0x%lx/0x%lx\n",
 		  compat, ro, incompat);
 
 	sb = journal->j_superblock;
@@ -2400,7 +2416,7 @@
 {
 	journal_superblock_t *sb;
 
-	jbd_debug(1, "Clear features 0x%lx/0x%lx/0x%lx\n",
+	jbd2_debug(1, "Clear features 0x%lx/0x%lx/0x%lx\n",
 		  compat, ro, incompat);
 
 	sb = journal->j_superblock;
@@ -2857,7 +2873,7 @@
 #endif
 	ret = kmem_cache_zalloc(jbd2_journal_head_cache, GFP_NOFS);
 	if (!ret) {
-		jbd_debug(1, "out of memory for journal_head\n");
+		jbd2_debug(1, "out of memory for journal_head\n");
 		pr_notice_ratelimited("ENOMEM in %s, retrying.\n", __func__);
 		ret = kmem_cache_zalloc(jbd2_journal_head_cache,
 				GFP_NOFS | __GFP_NOFAIL);
@@ -2970,6 +2986,7 @@
 	jbd_unlock_bh_journal_head(bh);
 	return jh;
 }
+EXPORT_SYMBOL(jbd2_journal_grab_journal_head);
 
 static void __journal_remove_journal_head(struct buffer_head *bh)
 {
@@ -3022,6 +3039,7 @@
 		jbd_unlock_bh_journal_head(bh);
 	}
 }
+EXPORT_SYMBOL(jbd2_journal_put_journal_head);
 
 /*
  * Initialize jbd inode head
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jbd2/recovery.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jbd2/recovery.c
@@ -224,12 +224,8 @@
 /* Make sure we wrap around the log correctly! */
 #define wrap(journal, var)						\
 do {									\
-	unsigned long _wrap_last =					\
-		jbd2_has_feature_fast_commit(journal) ?			\
-			(journal)->j_fc_last : (journal)->j_last;	\
-									\
-	if (var >= _wrap_last)						\
-		var -= (_wrap_last - (journal)->j_first);		\
+	if (var >= (journal)->j_last)					\
+		var -= ((journal)->j_last - (journal)->j_first);	\
 } while (0)
 
 static int fc_do_one_pass(journal_t *journal,
@@ -245,17 +241,18 @@
 		return 0;
 
 	while (next_fc_block <= journal->j_fc_last) {
-		jbd_debug(3, "Fast commit replay: next block %ld\n",
+		jbd2_debug(3, "Fast commit replay: next block %ld\n",
 			  next_fc_block);
 		err = jread(&bh, journal, next_fc_block);
 		if (err) {
-			jbd_debug(3, "Fast commit replay: read error\n");
+			jbd2_debug(3, "Fast commit replay: read error\n");
 			break;
 		}
 
 		err = journal->j_fc_replay_callback(journal, bh, pass,
 					next_fc_block - journal->j_fc_first,
 					expected_commit_id);
+		brelse(bh);
 		next_fc_block++;
 		if (err < 0 || err == JBD2_FC_REPLAY_STOP)
 			break;
@@ -263,7 +260,7 @@
 	}
 
 	if (err)
-		jbd_debug(3, "Fast commit replay failed, err = %d\n", err);
+		jbd2_debug(3, "Fast commit replay failed, err = %d\n", err);
 
 	return err;
 }
@@ -286,6 +283,8 @@
 	journal_superblock_t *	sb;
 
 	struct recovery_info	info;
+	errseq_t		wb_err;
+	struct address_space	*mapping;
 
 	memset(&info, 0, sizeof(info));
 	sb = journal->j_superblock;
@@ -297,22 +296,25 @@
 	 */
 
 	if (!sb->s_start) {
-		jbd_debug(1, "No recovery required, last transaction %d\n",
+		jbd2_debug(1, "No recovery required, last transaction %d\n",
 			  be32_to_cpu(sb->s_sequence));
 		journal->j_transaction_sequence = be32_to_cpu(sb->s_sequence) + 1;
 		return 0;
 	}
 
+	wb_err = 0;
+	mapping = journal->j_fs_dev->bd_inode->i_mapping;
+	errseq_check_and_advance(&mapping->wb_err, &wb_err);
 	err = do_one_pass(journal, &info, PASS_SCAN);
 	if (!err)
 		err = do_one_pass(journal, &info, PASS_REVOKE);
 	if (!err)
 		err = do_one_pass(journal, &info, PASS_REPLAY);
 
-	jbd_debug(1, "JBD2: recovery, exit status %d, "
+	jbd2_debug(1, "JBD2: recovery, exit status %d, "
 		  "recovered transactions %u to %u\n",
 		  err, info.start_transaction, info.end_transaction);
-	jbd_debug(1, "JBD2: Replayed %d and revoked %d/%d blocks\n",
+	jbd2_debug(1, "JBD2: Replayed %d and revoked %d/%d blocks\n",
 		  info.nr_replays, info.nr_revoke_hits, info.nr_revokes);
 
 	/* Restart the log at the next transaction ID, thus invalidating
@@ -323,6 +325,9 @@
 	err2 = sync_blockdev(journal->j_fs_dev);
 	if (!err)
 		err = err2;
+	err2 = errseq_check_and_advance(&mapping->wb_err, &wb_err);
+	if (!err)
+		err = err2;
 	/* Make sure all replayed data is on permanent storage */
 	if (journal->j_flags & JBD2_BARRIER) {
 		err2 = blkdev_issue_flush(journal->j_fs_dev);
@@ -362,7 +367,7 @@
 #ifdef CONFIG_JBD2_DEBUG
 		int dropped = info.end_transaction - 
 			be32_to_cpu(journal->j_superblock->s_sequence);
-		jbd_debug(1,
+		jbd2_debug(1,
 			  "JBD2: ignoring %d transaction%s from the journal.\n",
 			  dropped, (dropped == 1) ? "" : "s");
 #endif
@@ -484,7 +489,7 @@
 	if (pass == PASS_SCAN)
 		info->start_transaction = first_commit_ID;
 
-	jbd_debug(1, "Starting recovery pass %d\n", pass);
+	jbd2_debug(1, "Starting recovery pass %d\n", pass);
 
 	/*
 	 * Now we walk through the log, transaction by transaction,
@@ -510,16 +515,14 @@
 			if (tid_geq(next_commit_ID, info->end_transaction))
 				break;
 
-		jbd_debug(2, "Scanning for sequence ID %u at %lu/%lu\n",
-			  next_commit_ID, next_log_block,
-			  jbd2_has_feature_fast_commit(journal) ?
-			  journal->j_fc_last : journal->j_last);
+		jbd2_debug(2, "Scanning for sequence ID %u at %lu/%lu\n",
+			  next_commit_ID, next_log_block, journal->j_last);
 
 		/* Skip over each chunk of the transaction looking
 		 * either the next descriptor block or the final commit
 		 * record. */
 
-		jbd_debug(3, "JBD2: checking block %ld\n", next_log_block);
+		jbd2_debug(3, "JBD2: checking block %ld\n", next_log_block);
 		err = jread(&bh, journal, next_log_block);
 		if (err)
 			goto failed;
@@ -542,7 +545,7 @@
 
 		blocktype = be32_to_cpu(tmp->h_blocktype);
 		sequence = be32_to_cpu(tmp->h_sequence);
-		jbd_debug(3, "Found magic %d, sequence %d\n",
+		jbd2_debug(3, "Found magic %d, sequence %d\n",
 			  blocktype, sequence);
 
 		if (sequence != next_commit_ID) {
@@ -575,7 +578,7 @@
 					goto failed;
 				}
 				need_check_commit_time = true;
-				jbd_debug(1,
+				jbd2_debug(1,
 					"invalid descriptor block found in %lu\n",
 					next_log_block);
 			}
@@ -758,7 +761,7 @@
 				 * It likely does not belong to same journal,
 				 * just end this recovery with success.
 				 */
-				jbd_debug(1, "JBD2: Invalid checksum ignored in transaction %u, likely stale data\n",
+				jbd2_debug(1, "JBD2: Invalid checksum ignored in transaction %u, likely stale data\n",
 					  next_commit_ID);
 				brelse(bh);
 				goto done;
@@ -826,7 +829,7 @@
 			if (pass == PASS_SCAN &&
 			    !jbd2_descriptor_block_csum_verify(journal,
 							       bh->b_data)) {
-				jbd_debug(1, "JBD2: invalid revoke block found in %lu\n",
+				jbd2_debug(1, "JBD2: invalid revoke block found in %lu\n",
 					  next_log_block);
 				need_check_commit_time = true;
 			}
@@ -845,7 +848,7 @@
 			continue;
 
 		default:
-			jbd_debug(3, "Unrecognised magic %d, end of scan.\n",
+			jbd2_debug(3, "Unrecognised magic %d, end of scan.\n",
 				  blocktype);
 			brelse(bh);
 			goto done;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jbd2/revoke.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jbd2/revoke.c
@@ -398,7 +398,7 @@
 	}
 	handle->h_revoke_credits--;
 
-	jbd_debug(2, "insert revoke for block %llu, bh_in=%p\n",blocknr, bh_in);
+	jbd2_debug(2, "insert revoke for block %llu, bh_in=%p\n",blocknr, bh_in);
 	err = insert_revoke_hash(journal, blocknr,
 				handle->h_transaction->t_tid);
 	BUFFER_TRACE(bh_in, "exit");
@@ -428,7 +428,7 @@
 	int did_revoke = 0;	/* akpm: debug */
 	struct buffer_head *bh = jh2bh(jh);
 
-	jbd_debug(4, "journal_head %p, cancelling revoke\n", jh);
+	jbd2_debug(4, "journal_head %p, cancelling revoke\n", jh);
 
 	/* Is the existing Revoke bit valid?  If so, we trust it, and
 	 * only perform the full cancel if the revoke bit is set.  If
@@ -444,7 +444,7 @@
 	if (need_cancel) {
 		record = find_revoke_record(journal, bh->b_blocknr);
 		if (record) {
-			jbd_debug(4, "cancelled existing revoke on "
+			jbd2_debug(4, "cancelled existing revoke on "
 				  "blocknr %llu\n", (unsigned long long)bh->b_blocknr);
 			spin_lock(&journal->j_revoke_lock);
 			list_del(&record->hash);
@@ -560,7 +560,7 @@
 	}
 	if (descriptor)
 		flush_descriptor(journal, descriptor, offset);
-	jbd_debug(1, "Wrote %d revoke records\n", count);
+	jbd2_debug(1, "Wrote %d revoke records\n", count);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jbd2/transaction.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jbd2/transaction.c
@@ -107,7 +107,6 @@
 	transaction->t_start_time = ktime_get();
 	transaction->t_tid = journal->j_transaction_sequence++;
 	transaction->t_expires = jiffies + journal->j_commit_interval;
-	spin_lock_init(&transaction->t_handle_lock);
 	atomic_set(&transaction->t_updates, 0);
 	atomic_set(&transaction->t_outstanding_credits,
 		   jbd2_descriptor_blocks_per_trans(journal) +
@@ -139,24 +138,21 @@
 /*
  * Update transaction's maximum wait time, if debugging is enabled.
  *
- * In order for t_max_wait to be reliable, it must be protected by a
- * lock.  But doing so will mean that start_this_handle() can not be
- * run in parallel on SMP systems, which limits our scalability.  So
- * unless debugging is enabled, we no longer update t_max_wait, which
- * means that maximum wait time reported by the jbd2_run_stats
- * tracepoint will always be zero.
+ * t_max_wait is carefully updated here with use of atomic compare exchange.
+ * Note that there could be multiplre threads trying to do this simultaneously
+ * hence using cmpxchg to avoid any use of locks in this case.
  */
 static inline void update_t_max_wait(transaction_t *transaction,
 				     unsigned long ts)
 {
 #ifdef CONFIG_JBD2_DEBUG
+	unsigned long oldts, newts;
 	if (jbd2_journal_enable_debug &&
 	    time_after(transaction->t_start, ts)) {
-		ts = jbd2_time_diff(ts, transaction->t_start);
-		spin_lock(&transaction->t_handle_lock);
-		if (ts > transaction->t_max_wait)
-			transaction->t_max_wait = ts;
-		spin_unlock(&transaction->t_handle_lock);
+		newts = jbd2_time_diff(ts, transaction->t_start);
+		oldts = READ_ONCE(transaction->t_max_wait);
+		while (oldts < newts)
+			oldts = cmpxchg(&transaction->t_max_wait, oldts, newts);
 	}
 #endif
 }
@@ -173,7 +169,7 @@
 	int need_to_start;
 	tid_t tid = journal->j_running_transaction->t_tid;
 
-	prepare_to_wait(&journal->j_wait_transaction_locked, &wait,
+	prepare_to_wait_exclusive(&journal->j_wait_transaction_locked, &wait,
 			TASK_UNINTERRUPTIBLE);
 	need_to_start = !tid_geq(journal->j_commit_request, tid);
 	read_unlock(&journal->j_state_lock);
@@ -199,7 +195,7 @@
 		read_unlock(&journal->j_state_lock);
 		return;
 	}
-	prepare_to_wait(&journal->j_wait_transaction_locked, &wait,
+	prepare_to_wait_exclusive(&journal->j_wait_transaction_locked, &wait,
 			TASK_UNINTERRUPTIBLE);
 	read_unlock(&journal->j_state_lock);
 	/*
@@ -378,7 +374,7 @@
 			return -ENOMEM;
 	}
 
-	jbd_debug(3, "New handle %p going live.\n", handle);
+	jbd2_debug(3, "New handle %p going live.\n", handle);
 
 	/*
 	 * We need to hold j_state_lock until t_updates has been incremented,
@@ -449,7 +445,7 @@
 	}
 
 	/* OK, account for the buffers that this operation expects to
-	 * use and add the handle to the running transaction. 
+	 * use and add the handle to the running transaction.
 	 */
 	update_t_max_wait(transaction, ts);
 	handle->h_transaction = transaction;
@@ -458,7 +454,7 @@
 	handle->h_start_jiffies = jiffies;
 	atomic_inc(&transaction->t_updates);
 	atomic_inc(&transaction->t_handle_count);
-	jbd_debug(4, "Handle %p given %d credits (total %d, free %lu)\n",
+	jbd2_debug(4, "Handle %p given %d credits (total %d, free %lu)\n",
 		  handle, blocks,
 		  atomic_read(&transaction->t_outstanding_credits),
 		  jbd2_log_space_left(journal));
@@ -679,7 +675,7 @@
 
 	/* Don't extend a locked-down transaction! */
 	if (transaction->t_state != T_RUNNING) {
-		jbd_debug(3, "denied handle %p %d blocks: "
+		jbd2_debug(3, "denied handle %p %d blocks: "
 			  "transaction not running\n", handle, nblocks);
 		goto error_out;
 	}
@@ -690,15 +686,14 @@
 		DIV_ROUND_UP(
 			handle->h_revoke_credits_requested,
 			journal->j_revoke_records_per_block);
-	spin_lock(&transaction->t_handle_lock);
 	wanted = atomic_add_return(nblocks,
 				   &transaction->t_outstanding_credits);
 
 	if (wanted > journal->j_max_transaction_buffers) {
-		jbd_debug(3, "denied handle %p %d blocks: "
+		jbd2_debug(3, "denied handle %p %d blocks: "
 			  "transaction too large\n", handle, nblocks);
 		atomic_sub(nblocks, &transaction->t_outstanding_credits);
-		goto unlock;
+		goto error_out;
 	}
 
 	trace_jbd2_handle_extend(journal->j_fs_dev->bd_dev,
@@ -713,9 +708,7 @@
 	handle->h_revoke_credits_requested += revoke_records;
 	result = 0;
 
-	jbd_debug(3, "extended handle %p by %d\n", handle, nblocks);
-unlock:
-	spin_unlock(&transaction->t_handle_lock);
+	jbd2_debug(3, "extended handle %p by %d\n", handle, nblocks);
 error_out:
 	read_unlock(&journal->j_state_lock);
 	return result;
@@ -803,7 +796,7 @@
 	 * First unlink the handle from its current transaction, and start the
 	 * commit on that.
 	 */
-	jbd_debug(2, "restarting handle %p\n", handle);
+	jbd2_debug(2, "restarting handle %p\n", handle);
 	stop_this_handle(handle);
 	handle->h_transaction = NULL;
 
@@ -836,6 +829,43 @@
 }
 EXPORT_SYMBOL(jbd2_journal_restart);
 
+/*
+ * Waits for any outstanding t_updates to finish.
+ * This is called with write j_state_lock held.
+ */
+void jbd2_journal_wait_updates(journal_t *journal)
+{
+	DEFINE_WAIT(wait);
+
+	while (1) {
+		/*
+		 * Note that the running transaction can get freed under us if
+		 * this transaction is getting committed in
+		 * jbd2_journal_commit_transaction() ->
+		 * jbd2_journal_free_transaction(). This can only happen when we
+		 * release j_state_lock -> schedule() -> acquire j_state_lock.
+		 * Hence we should everytime retrieve new j_running_transaction
+		 * value (after j_state_lock release acquire cycle), else it may
+		 * lead to use-after-free of old freed transaction.
+		 */
+		transaction_t *transaction = journal->j_running_transaction;
+
+		if (!transaction)
+			break;
+
+		prepare_to_wait(&journal->j_wait_updates, &wait,
+				TASK_UNINTERRUPTIBLE);
+		if (!atomic_read(&transaction->t_updates)) {
+			finish_wait(&journal->j_wait_updates, &wait);
+			break;
+		}
+		write_unlock(&journal->j_state_lock);
+		schedule();
+		finish_wait(&journal->j_wait_updates, &wait);
+		write_lock(&journal->j_state_lock);
+	}
+}
+
 /**
  * jbd2_journal_lock_updates () - establish a transaction barrier.
  * @journal:  Journal to establish a barrier on.
@@ -848,8 +878,6 @@
  */
 void jbd2_journal_lock_updates(journal_t *journal)
 {
-	DEFINE_WAIT(wait);
-
 	jbd2_might_wait_for_commit(journal);
 
 	write_lock(&journal->j_state_lock);
@@ -863,27 +891,9 @@
 		write_lock(&journal->j_state_lock);
 	}
 
-	/* Wait until there are no running updates */
-	while (1) {
-		transaction_t *transaction = journal->j_running_transaction;
-
-		if (!transaction)
-			break;
+	/* Wait until there are no running t_updates */
+	jbd2_journal_wait_updates(journal);
 
-		spin_lock(&transaction->t_handle_lock);
-		prepare_to_wait(&journal->j_wait_updates, &wait,
-				TASK_UNINTERRUPTIBLE);
-		if (!atomic_read(&transaction->t_updates)) {
-			spin_unlock(&transaction->t_handle_lock);
-			finish_wait(&journal->j_wait_updates, &wait);
-			break;
-		}
-		spin_unlock(&transaction->t_handle_lock);
-		write_unlock(&journal->j_state_lock);
-		schedule();
-		finish_wait(&journal->j_wait_updates, &wait);
-		write_lock(&journal->j_state_lock);
-	}
 	write_unlock(&journal->j_state_lock);
 
 	/*
@@ -911,7 +921,7 @@
 	write_lock(&journal->j_state_lock);
 	--journal->j_barrier_count;
 	write_unlock(&journal->j_state_lock);
-	wake_up(&journal->j_wait_transaction_locked);
+	wake_up_all(&journal->j_wait_transaction_locked);
 }
 
 static void warn_dirty_buffer(struct buffer_head *bh)
@@ -970,7 +980,7 @@
 
 	journal = transaction->t_journal;
 
-	jbd_debug(5, "journal_head %p, force_copy %d\n", jh, force_copy);
+	jbd2_debug(5, "journal_head %p, force_copy %d\n", jh, force_copy);
 
 	JBUFFER_TRACE(jh, "entry");
 repeat:
@@ -1001,36 +1011,28 @@
 	 * ie. locked but not dirty) or tune2fs (which may actually have
 	 * the buffer dirtied, ugh.)  */
 
-	if (buffer_dirty(bh)) {
+	if (buffer_dirty(bh) && jh->b_transaction) {
+		warn_dirty_buffer(bh);
 		/*
-		 * First question: is this buffer already part of the current
-		 * transaction or the existing committing transaction?
-		 */
-		if (jh->b_transaction) {
-			J_ASSERT_JH(jh,
-				jh->b_transaction == transaction ||
-				jh->b_transaction ==
-					journal->j_committing_transaction);
-			if (jh->b_next_transaction)
-				J_ASSERT_JH(jh, jh->b_next_transaction ==
-							transaction);
-			warn_dirty_buffer(bh);
-		}
-		/*
-		 * In any case we need to clean the dirty flag and we must
-		 * do it under the buffer lock to be sure we don't race
-		 * with running write-out.
+		 * We need to clean the dirty flag and we must do it under the
+		 * buffer lock to be sure we don't race with running write-out.
 		 */
 		JBUFFER_TRACE(jh, "Journalling dirty buffer");
 		clear_buffer_dirty(bh);
+		/*
+		 * The buffer is going to be added to BJ_Reserved list now and
+		 * nothing guarantees jbd2_journal_dirty_metadata() will be
+		 * ever called for it. So we need to set jbddirty bit here to
+		 * make sure the buffer is dirtied and written out when the
+		 * journaling machinery is done with it.
+		 */
 		set_buffer_jbddirty(bh);
 	}
 
-	unlock_buffer(bh);
-
 	error = -EROFS;
 	if (is_handle_aborted(handle)) {
 		spin_unlock(&jh->b_state_lock);
+		unlock_buffer(bh);
 		goto out;
 	}
 	error = 0;
@@ -1040,8 +1042,10 @@
 	 * b_next_transaction points to it
 	 */
 	if (jh->b_transaction == transaction ||
-	    jh->b_next_transaction == transaction)
+	    jh->b_next_transaction == transaction) {
+		unlock_buffer(bh);
 		goto done;
+	}
 
 	/*
 	 * this is the first time this transaction is touching this buffer,
@@ -1065,10 +1069,24 @@
 		 */
 		smp_wmb();
 		spin_lock(&journal->j_list_lock);
+		if (test_clear_buffer_dirty(bh)) {
+			/*
+			 * Execute buffer dirty clearing and jh->b_transaction
+			 * assignment under journal->j_list_lock locked to
+			 * prevent bh being removed from checkpoint list if
+			 * the buffer is in an intermediate state (not dirty
+			 * and jh->b_transaction is NULL).
+			 */
+			JBUFFER_TRACE(jh, "Journalling dirty buffer");
+			set_buffer_jbddirty(bh);
+		}
 		__jbd2_journal_file_buffer(jh, transaction, BJ_Reserved);
 		spin_unlock(&journal->j_list_lock);
+		unlock_buffer(bh);
 		goto done;
 	}
+	unlock_buffer(bh);
+
 	/*
 	 * If there is already a copy-out version of this buffer, then we don't
 	 * need to make another one
@@ -1262,7 +1280,7 @@
 	struct journal_head *jh = jbd2_journal_add_journal_head(bh);
 	int err;
 
-	jbd_debug(5, "journal_head %p\n", jh);
+	jbd2_debug(5, "journal_head %p\n", jh);
 	err = -EROFS;
 	if (is_handle_aborted(handle))
 		goto out;
@@ -1477,8 +1495,6 @@
 	struct journal_head *jh;
 	int ret = 0;
 
-	if (is_handle_aborted(handle))
-		return -EROFS;
 	if (!buffer_jbd(bh))
 		return -EUCLEAN;
 
@@ -1487,7 +1503,7 @@
 	 * of the running transaction.
 	 */
 	jh = bh2jh(bh);
-	jbd_debug(5, "journal_head %p\n", jh);
+	jbd2_debug(5, "journal_head %p\n", jh);
 	JBUFFER_TRACE(jh, "entry");
 
 	/*
@@ -1525,6 +1541,18 @@
 	journal = transaction->t_journal;
 	spin_lock(&jh->b_state_lock);
 
+	if (is_handle_aborted(handle)) {
+		/*
+		 * Check journal aborting with @jh->b_state_lock locked,
+		 * since 'jh->b_transaction' could be replaced with
+		 * 'jh->b_next_transaction' during old transaction
+		 * committing if journal aborted, which may fail
+		 * assertion on 'jh->b_frozen_data == NULL'.
+		 */
+		ret = -EROFS;
+		goto out_unlock_bh;
+	}
+
 	if (jh->b_modified == 0) {
 		/*
 		 * This buffer's got modified and becoming part
@@ -1757,8 +1785,7 @@
 		 * Otherwise, if the buffer has been written to disk,
 		 * it is safe to remove the checkpoint and drop it.
 		 */
-		if (!buffer_dirty(bh)) {
-			__jbd2_journal_remove_checkpoint(jh);
+		if (jbd2_journal_try_remove_checkpoint(jh) >= 0) {
 			spin_unlock(&journal->j_list_lock);
 			goto drop;
 		}
@@ -1809,7 +1836,7 @@
 	pid_t pid;
 
 	if (--handle->h_ref > 0) {
-		jbd_debug(4, "h_ref %d -> %d\n", handle->h_ref + 1,
+		jbd2_debug(4, "h_ref %d -> %d\n", handle->h_ref + 1,
 						 handle->h_ref);
 		if (is_handle_aborted(handle))
 			return -EIO;
@@ -1829,7 +1856,7 @@
 	if (is_handle_aborted(handle))
 		err = -EIO;
 
-	jbd_debug(4, "Handle %p going down\n", handle);
+	jbd2_debug(4, "Handle %p going down\n", handle);
 	trace_jbd2_handle_stats(journal->j_fs_dev->bd_dev,
 				tid, handle->h_type, handle->h_line_no,
 				jiffies - handle->h_start_jiffies,
@@ -1907,7 +1934,7 @@
 		 * completes the commit thread, it just doesn't write
 		 * anything to disk. */
 
-		jbd_debug(2, "transaction too old, requesting commit for "
+		jbd2_debug(2, "transaction too old, requesting commit for "
 					"handle %p\n", handle);
 		/* This is non-blocking */
 		jbd2_log_start_commit(journal, tid);
@@ -2085,20 +2112,14 @@
 
 	jh = bh2jh(bh);
 
-	if (buffer_locked(bh) || buffer_dirty(bh))
-		goto out;
-
 	if (jh->b_next_transaction != NULL || jh->b_transaction != NULL)
-		goto out;
+		return;
 
 	spin_lock(&journal->j_list_lock);
-	if (jh->b_cp_transaction != NULL) {
-		/* written-back checkpointed metadata buffer */
-		JBUFFER_TRACE(jh, "remove from checkpoint list");
-		__jbd2_journal_remove_checkpoint(jh);
-	}
+	/* Remove written-back checkpointed metadata buffer */
+	if (jh->b_cp_transaction != NULL)
+		jbd2_journal_try_remove_checkpoint(jh);
 	spin_unlock(&journal->j_list_lock);
-out:
 	return;
 }
 
@@ -2360,6 +2381,9 @@
 			spin_unlock(&jh->b_state_lock);
 			write_unlock(&journal->j_state_lock);
 			jbd2_journal_put_journal_head(jh);
+			/* Already zapped buffer? Nothing to do... */
+			if (!bh->b_bdev)
+				return 0;
 			return -EBUSY;
 		}
 		/*
@@ -2654,7 +2678,7 @@
 		return -EROFS;
 	journal = transaction->t_journal;
 
-	jbd_debug(4, "Adding inode %lu, tid:%d\n", jinode->i_vfs_inode->i_ino,
+	jbd2_debug(4, "Adding inode %lu, tid:%d\n", jinode->i_vfs_inode->i_ino,
 			transaction->t_tid);
 
 	spin_lock(&journal->j_list_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/build.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/build.c
@@ -211,7 +211,10 @@
 		ic->scan_dents = NULL;
 		cond_resched();
 	}
-	jffs2_build_xattr_subsystem(c);
+	ret = jffs2_build_xattr_subsystem(c);
+	if (ret)
+		goto exit;
+
 	c->flags &= ~JFFS2_SB_FLAG_BUILDING;
 
 	dbg_fsbuild("FS build complete\n");
@@ -415,13 +418,15 @@
 		jffs2_free_ino_caches(c);
 		jffs2_free_raw_node_refs(c);
 		ret = -EIO;
-		goto out_free;
+		goto out_sum_exit;
 	}
 
 	jffs2_calc_trigger_levels(c);
 
 	return 0;
 
+ out_sum_exit:
+	jffs2_sum_exit(c);
  out_free:
 	kvfree(c->blocks);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/compr_rtime.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/compr_rtime.c
@@ -95,6 +95,9 @@
 
 		positions[value]=outpos;
 		if (repeat) {
+			if ((outpos + repeat) > destlen) {
+				return 1;
+			}
 			if (backoffs + repeat >= outpos) {
 				while(repeat) {
 					cpage_out[outpos++] = cpage_out[backoffs++];
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/erase.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/erase.c
@@ -340,10 +340,9 @@
 		} while(--retlen);
 		mtd_unpoint(c->mtd, jeb->offset, c->sector_size);
 		if (retlen) {
-			pr_warn("Newly-erased block contained word 0x%lx at offset 0x%08tx\n",
-				*wordebuf,
-				jeb->offset +
-				c->sector_size-retlen * sizeof(*wordebuf));
+			*bad_offset = jeb->offset + c->sector_size - retlen * sizeof(*wordebuf);
+			pr_warn("Newly-erased block contained word 0x%lx at offset 0x%08x\n",
+				*wordebuf, *bad_offset);
 			return -EIO;
 		}
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/file.c
@@ -136,31 +136,25 @@
 	struct page *pg;
 	struct inode *inode = mapping->host;
 	struct jffs2_inode_info *f = JFFS2_INODE_INFO(inode);
+	struct jffs2_sb_info *c = JFFS2_SB_INFO(inode->i_sb);
 	pgoff_t index = pos >> PAGE_SHIFT;
-	uint32_t pageofs = index << PAGE_SHIFT;
 	int ret = 0;
 
-	pg = grab_cache_page_write_begin(mapping, index, flags);
-	if (!pg)
-		return -ENOMEM;
-	*pagep = pg;
-
 	jffs2_dbg(1, "%s()\n", __func__);
 
-	if (pageofs > inode->i_size) {
-		/* Make new hole frag from old EOF to new page */
-		struct jffs2_sb_info *c = JFFS2_SB_INFO(inode->i_sb);
+	if (pos > inode->i_size) {
+		/* Make new hole frag from old EOF to new position */
 		struct jffs2_raw_inode ri;
 		struct jffs2_full_dnode *fn;
 		uint32_t alloc_len;
 
-		jffs2_dbg(1, "Writing new hole frag 0x%x-0x%x between current EOF and new page\n",
-			  (unsigned int)inode->i_size, pageofs);
+		jffs2_dbg(1, "Writing new hole frag 0x%x-0x%x between current EOF and new position\n",
+			  (unsigned int)inode->i_size, (uint32_t)pos);
 
 		ret = jffs2_reserve_space(c, sizeof(ri), &alloc_len,
 					  ALLOC_NORMAL, JFFS2_SUMMARY_INODE_SIZE);
 		if (ret)
-			goto out_page;
+			goto out_err;
 
 		mutex_lock(&f->sem);
 		memset(&ri, 0, sizeof(ri));
@@ -175,10 +169,10 @@
 		ri.mode = cpu_to_jemode(inode->i_mode);
 		ri.uid = cpu_to_je16(i_uid_read(inode));
 		ri.gid = cpu_to_je16(i_gid_read(inode));
-		ri.isize = cpu_to_je32(max((uint32_t)inode->i_size, pageofs));
+		ri.isize = cpu_to_je32((uint32_t)pos);
 		ri.atime = ri.ctime = ri.mtime = cpu_to_je32(JFFS2_NOW());
 		ri.offset = cpu_to_je32(inode->i_size);
-		ri.dsize = cpu_to_je32(pageofs - inode->i_size);
+		ri.dsize = cpu_to_je32((uint32_t)pos - inode->i_size);
 		ri.csize = cpu_to_je32(0);
 		ri.compr = JFFS2_COMPR_ZERO;
 		ri.node_crc = cpu_to_je32(crc32(0, &ri, sizeof(ri)-8));
@@ -190,7 +184,7 @@
 			ret = PTR_ERR(fn);
 			jffs2_complete_reservation(c);
 			mutex_unlock(&f->sem);
-			goto out_page;
+			goto out_err;
 		}
 		ret = jffs2_add_full_dnode_to_inode(c, f, fn);
 		if (f->metadata) {
@@ -205,14 +199,27 @@
 			jffs2_free_full_dnode(fn);
 			jffs2_complete_reservation(c);
 			mutex_unlock(&f->sem);
-			goto out_page;
+			goto out_err;
 		}
 		jffs2_complete_reservation(c);
-		inode->i_size = pageofs;
+		inode->i_size = pos;
 		mutex_unlock(&f->sem);
 	}
 
 	/*
+	 * While getting a page and reading data in, lock c->alloc_sem until
+	 * the page is Uptodate. Otherwise GC task may attempt to read the same
+	 * page in read_cache_page(), which causes a deadlock.
+	 */
+	mutex_lock(&c->alloc_sem);
+	pg = grab_cache_page_write_begin(mapping, index, flags);
+	if (!pg) {
+		ret = -ENOMEM;
+		goto release_sem;
+	}
+	*pagep = pg;
+
+	/*
 	 * Read in the page if it wasn't already present. Cannot optimize away
 	 * the whole page write case until jffs2_write_end can handle the
 	 * case of a short-copy.
@@ -221,15 +228,17 @@
 		mutex_lock(&f->sem);
 		ret = jffs2_do_readpage_nolock(inode, pg);
 		mutex_unlock(&f->sem);
-		if (ret)
-			goto out_page;
+		if (ret) {
+			unlock_page(pg);
+			put_page(pg);
+			goto release_sem;
+		}
 	}
 	jffs2_dbg(1, "end write_begin(). pg->flags %lx\n", pg->flags);
-	return ret;
 
-out_page:
-	unlock_page(pg);
-	put_page(pg);
+release_sem:
+	mutex_unlock(&c->alloc_sem);
+out_err:
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/fs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/fs.c
@@ -603,8 +603,9 @@
 	jffs2_free_ino_caches(c);
 	jffs2_free_raw_node_refs(c);
 	kvfree(c->blocks);
- out_inohash:
 	jffs2_clear_xattr_subsystem(c);
+	jffs2_sum_exit(c);
+ out_inohash:
 	kfree(c->inocache_list);
  out_wbuf:
 	jffs2_flash_cleanup(c);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/scan.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/scan.c
@@ -136,7 +136,7 @@
 		if (!s) {
 			JFFS2_WARNING("Can't allocate memory for summary\n");
 			ret = -ENOMEM;
-			goto out;
+			goto out_buf;
 		}
 	}
 
@@ -275,13 +275,15 @@
 	}
 	ret = 0;
  out:
+	jffs2_sum_reset_collected(s);
+	kfree(s);
+ out_buf:
 	if (buf_size)
 		kfree(flashbuf);
 #ifndef __ECOS
 	else
 		mtd_unpoint(c->mtd, 0, c->mtd->size);
 #endif
-	kfree(s);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/super.c
@@ -58,6 +58,7 @@
 	struct jffs2_inode_info *f = foo;
 
 	mutex_init(&f->sem);
+	f->target = NULL;
 	inode_init_once(&f->vfs_inode);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/xattr.c
@@ -772,10 +772,10 @@
 }
 
 #define XREF_TMPHASH_SIZE	(128)
-void jffs2_build_xattr_subsystem(struct jffs2_sb_info *c)
+int jffs2_build_xattr_subsystem(struct jffs2_sb_info *c)
 {
 	struct jffs2_xattr_ref *ref, *_ref;
-	struct jffs2_xattr_ref *xref_tmphash[XREF_TMPHASH_SIZE];
+	struct jffs2_xattr_ref **xref_tmphash;
 	struct jffs2_xattr_datum *xd, *_xd;
 	struct jffs2_inode_cache *ic;
 	struct jffs2_raw_node_ref *raw;
@@ -784,9 +784,12 @@
 
 	BUG_ON(!(c->flags & JFFS2_SB_FLAG_BUILDING));
 
+	xref_tmphash = kcalloc(XREF_TMPHASH_SIZE,
+			       sizeof(struct jffs2_xattr_ref *), GFP_KERNEL);
+	if (!xref_tmphash)
+		return -ENOMEM;
+
 	/* Phase.1 : Merge same xref */
-	for (i=0; i < XREF_TMPHASH_SIZE; i++)
-		xref_tmphash[i] = NULL;
 	for (ref=c->xref_temp; ref; ref=_ref) {
 		struct jffs2_xattr_ref *tmp;
 
@@ -884,6 +887,8 @@
 		     "%u of xref (%u dead, %u orphan) found.\n",
 		     xdatum_count, xdatum_unchecked_count, xdatum_orphan_count,
 		     xref_count, xref_dead_count, xref_orphan_count);
+	kfree(xref_tmphash);
+	return 0;
 }
 
 struct jffs2_xattr_datum *jffs2_setup_xattr_datum(struct jffs2_sb_info *c,
@@ -1106,6 +1111,9 @@
 		return rc;
 
 	request = PAD(sizeof(struct jffs2_raw_xattr) + strlen(xname) + 1 + size);
+	if (request > c->sector_size - c->cleanmarker_size)
+		return -ERANGE;
+
 	rc = jffs2_reserve_space(c, request, &length,
 				 ALLOC_NORMAL, JFFS2_SUMMARY_XATTR_SIZE);
 	if (rc) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jffs2/xattr.h
+++ linux-xilinx-zynqmp-5.15.0/fs/jffs2/xattr.h
@@ -71,7 +71,7 @@
 #ifdef CONFIG_JFFS2_FS_XATTR
 
 extern void jffs2_init_xattr_subsystem(struct jffs2_sb_info *c);
-extern void jffs2_build_xattr_subsystem(struct jffs2_sb_info *c);
+extern int jffs2_build_xattr_subsystem(struct jffs2_sb_info *c);
 extern void jffs2_clear_xattr_subsystem(struct jffs2_sb_info *c);
 
 extern struct jffs2_xattr_datum *jffs2_setup_xattr_datum(struct jffs2_sb_info *c,
@@ -103,7 +103,7 @@
 #else
 
 #define jffs2_init_xattr_subsystem(c)
-#define jffs2_build_xattr_subsystem(c)
+#define jffs2_build_xattr_subsystem(c)		(0)
 #define jffs2_clear_xattr_subsystem(c)
 
 #define jffs2_xattr_do_crccheck_inode(c, ic)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/inode.c
@@ -146,12 +146,13 @@
 		dquot_initialize(inode);
 
 		if (JFS_IP(inode)->fileset == FILESYSTEM_I) {
+			struct inode *ipimap = JFS_SBI(inode->i_sb)->ipimap;
 			truncate_inode_pages_final(&inode->i_data);
 
 			if (test_cflag(COMMIT_Freewmap, inode))
 				jfs_free_zero_link(inode);
 
-			if (JFS_SBI(inode->i_sb)->ipimap)
+			if (ipimap && JFS_IP(ipimap)->i_imap)
 				diFree(inode);
 
 			/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_discard.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_discard.c
@@ -65,7 +65,7 @@
 int jfs_ioc_trim(struct inode *ip, struct fstrim_range *range)
 {
 	struct inode *ipbmap = JFS_SBI(ip->i_sb)->ipbmap;
-	struct bmap *bmp = JFS_SBI(ip->i_sb)->bmap;
+	struct bmap *bmp;
 	struct super_block *sb = ipbmap->i_sb;
 	int agno, agno_end;
 	u64 start, end, minlen;
@@ -83,10 +83,15 @@
 	if (minlen == 0)
 		minlen = 1;
 
+	down_read(&sb->s_umount);
+	bmp = JFS_SBI(ip->i_sb)->bmap;
+
 	if (minlen > bmp->db_agsize ||
 	    start >= bmp->db_mapsize ||
-	    range->len < sb->s_blocksize)
+	    range->len < sb->s_blocksize) {
+		up_read(&sb->s_umount);
 		return -EINVAL;
+	}
 
 	if (end >= bmp->db_mapsize)
 		end = bmp->db_mapsize - 1;
@@ -100,6 +105,8 @@
 		trimmed += dbDiscardAG(ip, agno, minlen);
 		agno++;
 	}
+
+	up_read(&sb->s_umount);
 	range->len = trimmed << sb->s_blocksize_bits;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_dmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_dmap.c
@@ -63,10 +63,10 @@
  */
 static void dbAllocBits(struct bmap * bmp, struct dmap * dp, s64 blkno,
 			int nblocks);
-static void dbSplit(dmtree_t * tp, int leafno, int splitsz, int newval);
-static int dbBackSplit(dmtree_t * tp, int leafno);
-static int dbJoin(dmtree_t * tp, int leafno, int newval);
-static void dbAdjTree(dmtree_t * tp, int leafno, int newval);
+static void dbSplit(dmtree_t *tp, int leafno, int splitsz, int newval, bool is_ctl);
+static int dbBackSplit(dmtree_t *tp, int leafno, bool is_ctl);
+static int dbJoin(dmtree_t *tp, int leafno, int newval, bool is_ctl);
+static void dbAdjTree(dmtree_t *tp, int leafno, int newval, bool is_ctl);
 static int dbAdjCtl(struct bmap * bmp, s64 blkno, int newval, int alloc,
 		    int level);
 static int dbAllocAny(struct bmap * bmp, s64 nblocks, int l2nb, s64 * results);
@@ -87,7 +87,7 @@
 static int dbExtend(struct inode *ip, s64 blkno, s64 nblocks, s64 addnblocks);
 static int dbFindBits(u32 word, int l2nb);
 static int dbFindCtl(struct bmap * bmp, int l2nb, int level, s64 * blkno);
-static int dbFindLeaf(dmtree_t * tp, int l2nb, int *leafidx);
+static int dbFindLeaf(dmtree_t *tp, int l2nb, int *leafidx, bool is_ctl);
 static int dbFreeBits(struct bmap * bmp, struct dmap * dp, s64 blkno,
 		      int nblocks);
 static int dbFreeDmap(struct bmap * bmp, struct dmap * dp, s64 blkno,
@@ -148,13 +148,14 @@
  *	0	- success
  *	-ENOMEM	- insufficient memory
  *	-EIO	- i/o error
+ *	-EINVAL - wrong bmap data
  */
 int dbMount(struct inode *ipbmap)
 {
 	struct bmap *bmp;
 	struct dbmap_disk *dbmp_le;
 	struct metapage *mp;
-	int i;
+	int i, err;
 
 	/*
 	 * allocate/initialize the in-memory bmap descriptor
@@ -169,24 +170,53 @@
 			   BMAPBLKNO << JFS_SBI(ipbmap->i_sb)->l2nbperpage,
 			   PSIZE, 0);
 	if (mp == NULL) {
-		kfree(bmp);
-		return -EIO;
+		err = -EIO;
+		goto err_kfree_bmp;
 	}
 
 	/* copy the on-disk bmap descriptor to its in-memory version. */
 	dbmp_le = (struct dbmap_disk *) mp->data;
 	bmp->db_mapsize = le64_to_cpu(dbmp_le->dn_mapsize);
 	bmp->db_nfree = le64_to_cpu(dbmp_le->dn_nfree);
+
 	bmp->db_l2nbperpage = le32_to_cpu(dbmp_le->dn_l2nbperpage);
+	if (bmp->db_l2nbperpage > L2PSIZE - L2MINBLOCKSIZE ||
+		bmp->db_l2nbperpage < 0) {
+		err = -EINVAL;
+		goto err_release_metapage;
+	}
+
 	bmp->db_numag = le32_to_cpu(dbmp_le->dn_numag);
+	if (!bmp->db_numag || bmp->db_numag > MAXAG) {
+		err = -EINVAL;
+		goto err_release_metapage;
+	}
+
 	bmp->db_maxlevel = le32_to_cpu(dbmp_le->dn_maxlevel);
 	bmp->db_maxag = le32_to_cpu(dbmp_le->dn_maxag);
 	bmp->db_agpref = le32_to_cpu(dbmp_le->dn_agpref);
+	if (bmp->db_maxag >= MAXAG || bmp->db_maxag < 0 ||
+		bmp->db_agpref >= MAXAG || bmp->db_agpref < 0) {
+		err = -EINVAL;
+		goto err_release_metapage;
+	}
+
 	bmp->db_aglevel = le32_to_cpu(dbmp_le->dn_aglevel);
 	bmp->db_agheight = le32_to_cpu(dbmp_le->dn_agheight);
 	bmp->db_agwidth = le32_to_cpu(dbmp_le->dn_agwidth);
 	bmp->db_agstart = le32_to_cpu(dbmp_le->dn_agstart);
 	bmp->db_agl2size = le32_to_cpu(dbmp_le->dn_agl2size);
+	if (bmp->db_agl2size > L2MAXL2SIZE - L2MAXAG ||
+	    bmp->db_agl2size < 0) {
+		err = -EINVAL;
+		goto err_release_metapage;
+	}
+
+	if (((bmp->db_mapsize - 1) >> bmp->db_agl2size) > MAXAG) {
+		err = -EINVAL;
+		goto err_release_metapage;
+	}
+
 	for (i = 0; i < MAXAG; i++)
 		bmp->db_agfree[i] = le64_to_cpu(dbmp_le->dn_agfree[i]);
 	bmp->db_agsize = le64_to_cpu(dbmp_le->dn_agsize);
@@ -207,6 +237,12 @@
 	BMAP_LOCK_INIT(bmp);
 
 	return (0);
+
+err_release_metapage:
+	release_metapage(mp);
+err_kfree_bmp:
+	kfree(bmp);
+	return err;
 }
 
 
@@ -240,6 +276,7 @@
 
 	/* free the memory for the in-memory bmap. */
 	kfree(bmp);
+	JFS_SBI(ipbmap->i_sb)->bmap = NULL;
 
 	return (0);
 }
@@ -378,7 +415,8 @@
 	}
 
 	/* write the last buffer. */
-	write_metapage(mp);
+	if (mp)
+		write_metapage(mp);
 
 	IREAD_UNLOCK(ipbmap);
 
@@ -614,7 +652,7 @@
 	 * average free space.
 	 */
 	for (i = 0 ; i < bmp->db_numag; i++, agpref++) {
-		if (agpref == bmp->db_numag)
+		if (agpref >= bmp->db_numag)
 			agpref = 0;
 
 		if (atomic_read(&bmp->db_active[agpref]))
@@ -1656,6 +1694,8 @@
 		} else if (rc == -ENOSPC) {
 			/* search for next smaller log2 block */
 			l2nb = BLKSTOL2(nblocks) - 1;
+			if (unlikely(l2nb < 0))
+				break;
 			nblocks = 1LL << l2nb;
 		} else {
 			/* Trim any already allocated blocks */
@@ -1747,7 +1787,7 @@
 		 * dbFindLeaf() returns the index of the leaf at which
 		 * free space was found.
 		 */
-		rc = dbFindLeaf((dmtree_t *) dcp, l2nb, &leafidx);
+		rc = dbFindLeaf((dmtree_t *) dcp, l2nb, &leafidx, true);
 
 		/* release the buffer.
 		 */
@@ -1848,6 +1888,9 @@
 			return -EIO;
 		dp = (struct dmap *) mp->data;
 
+		if (dp->tree.budmin < 0)
+			return -EIO;
+
 		/* try to allocate the blocks.
 		 */
 		rc = dbAllocDmapLev(bmp, dp, (int) nblocks, l2nb, results);
@@ -1994,9 +2037,12 @@
 	 * free space.  if sufficient free space is found, dbFindLeaf()
 	 * returns the index of the leaf at which free space was found.
 	 */
-	if (dbFindLeaf((dmtree_t *) & dp->tree, l2nb, &leafidx))
+	if (dbFindLeaf((dmtree_t *) &dp->tree, l2nb, &leafidx, false))
 		return -ENOSPC;
 
+	if (leafidx < 0)
+		return -EIO;
+
 	/* determine the block number within the file system corresponding
 	 * to the leaf at which free space was found.
 	 */
@@ -2130,7 +2176,7 @@
 		 * system.
 		 */
 		if (dp->tree.stree[word] == NOFREE)
-			dbBackSplit((dmtree_t *) & dp->tree, word);
+			dbBackSplit((dmtree_t *)&dp->tree, word, false);
 
 		dbAllocBits(bmp, dp, blkno, nblocks);
 	}
@@ -2216,7 +2262,7 @@
 			 * the binary system of the leaves if need be.
 			 */
 			dbSplit(tp, word, BUDMIN,
-				dbMaxBud((u8 *) & dp->wmap[word]));
+				dbMaxBud((u8 *)&dp->wmap[word]), false);
 
 			word += 1;
 		} else {
@@ -2256,7 +2302,7 @@
 				 * system of the leaves to reflect the current
 				 * allocation (size).
 				 */
-				dbSplit(tp, word, size, NOFREE);
+				dbSplit(tp, word, size, NOFREE, false);
 
 				/* get the number of dmap words handled */
 				nw = BUDSIZE(size, BUDMIN);
@@ -2363,7 +2409,7 @@
 			/* update the leaf for this dmap word.
 			 */
 			rc = dbJoin(tp, word,
-				    dbMaxBud((u8 *) & dp->wmap[word]));
+				    dbMaxBud((u8 *)&dp->wmap[word]), false);
 			if (rc)
 				return rc;
 
@@ -2396,7 +2442,7 @@
 
 				/* update the leaf.
 				 */
-				rc = dbJoin(tp, word, size);
+				rc = dbJoin(tp, word, size, false);
 				if (rc)
 					return rc;
 
@@ -2548,16 +2594,16 @@
 		 * that it is at the front of a binary buddy system.
 		 */
 		if (oldval == NOFREE) {
-			rc = dbBackSplit((dmtree_t *) dcp, leafno);
+			rc = dbBackSplit((dmtree_t *)dcp, leafno, true);
 			if (rc) {
 				release_metapage(mp);
 				return rc;
 			}
 			oldval = dcp->stree[ti];
 		}
-		dbSplit((dmtree_t *) dcp, leafno, dcp->budmin, newval);
+		dbSplit((dmtree_t *) dcp, leafno, dcp->budmin, newval, true);
 	} else {
-		rc = dbJoin((dmtree_t *) dcp, leafno, newval);
+		rc = dbJoin((dmtree_t *) dcp, leafno, newval, true);
 		if (rc) {
 			release_metapage(mp);
 			return rc;
@@ -2588,7 +2634,7 @@
 				 */
 				if (alloc) {
 					dbJoin((dmtree_t *) dcp, leafno,
-					       oldval);
+					       oldval, true);
 				} else {
 					/* the dbJoin() above might have
 					 * caused a larger binary buddy system
@@ -2598,9 +2644,9 @@
 					 */
 					if (dcp->stree[ti] == NOFREE)
 						dbBackSplit((dmtree_t *)
-							    dcp, leafno);
+							    dcp, leafno, true);
 					dbSplit((dmtree_t *) dcp, leafno,
-						dcp->budmin, oldval);
+						dcp->budmin, oldval, true);
 				}
 
 				/* release the buffer and return the error.
@@ -2648,7 +2694,7 @@
  *
  * serialization: IREAD_LOCK(ipbmap) or IWRITE_LOCK(ipbmap) held on entry/exit;
  */
-static void dbSplit(dmtree_t * tp, int leafno, int splitsz, int newval)
+static void dbSplit(dmtree_t *tp, int leafno, int splitsz, int newval, bool is_ctl)
 {
 	int budsz;
 	int cursz;
@@ -2670,7 +2716,7 @@
 		while (cursz >= splitsz) {
 			/* update the buddy's leaf with its new value.
 			 */
-			dbAdjTree(tp, leafno ^ budsz, cursz);
+			dbAdjTree(tp, leafno ^ budsz, cursz, is_ctl);
 
 			/* on to the next size and buddy.
 			 */
@@ -2682,7 +2728,7 @@
 	/* adjust the dmap tree to reflect the specified leaf's new
 	 * value.
 	 */
-	dbAdjTree(tp, leafno, newval);
+	dbAdjTree(tp, leafno, newval, is_ctl);
 }
 
 
@@ -2713,7 +2759,7 @@
  *
  * serialization: IREAD_LOCK(ipbmap) or IWRITE_LOCK(ipbmap) held on entry/exit;
  */
-static int dbBackSplit(dmtree_t * tp, int leafno)
+static int dbBackSplit(dmtree_t *tp, int leafno, bool is_ctl)
 {
 	int budsz, bud, w, bsz, size;
 	int cursz;
@@ -2764,7 +2810,7 @@
 				 * system in two.
 				 */
 				cursz = leaf[bud] - 1;
-				dbSplit(tp, bud, cursz, cursz);
+				dbSplit(tp, bud, cursz, cursz, is_ctl);
 				break;
 			}
 		}
@@ -2792,7 +2838,7 @@
  *
  * RETURN VALUES: none
  */
-static int dbJoin(dmtree_t * tp, int leafno, int newval)
+static int dbJoin(dmtree_t *tp, int leafno, int newval, bool is_ctl)
 {
 	int budsz, buddy;
 	s8 *leaf;
@@ -2847,12 +2893,12 @@
 			if (leafno < buddy) {
 				/* leafno is the left buddy.
 				 */
-				dbAdjTree(tp, buddy, NOFREE);
+				dbAdjTree(tp, buddy, NOFREE, is_ctl);
 			} else {
 				/* buddy is the left buddy and becomes
 				 * leafno.
 				 */
-				dbAdjTree(tp, leafno, NOFREE);
+				dbAdjTree(tp, leafno, NOFREE, is_ctl);
 				leafno = buddy;
 			}
 
@@ -2865,7 +2911,7 @@
 
 	/* update the leaf value.
 	 */
-	dbAdjTree(tp, leafno, newval);
+	dbAdjTree(tp, leafno, newval, is_ctl);
 
 	return 0;
 }
@@ -2886,15 +2932,20 @@
  *
  * RETURN VALUES: none
  */
-static void dbAdjTree(dmtree_t * tp, int leafno, int newval)
+static void dbAdjTree(dmtree_t *tp, int leafno, int newval, bool is_ctl)
 {
 	int lp, pp, k;
-	int max;
+	int max, size;
+
+	size = is_ctl ? CTLTREESIZE : TREESIZE;
 
 	/* pick up the index of the leaf for this leafno.
 	 */
 	lp = leafno + le32_to_cpu(tp->dmt_leafidx);
 
+	if (WARN_ON_ONCE(lp >= size || lp < 0))
+		return;
+
 	/* is the current value the same as the old value ?  if so,
 	 * there is nothing to do.
 	 */
@@ -2908,6 +2959,9 @@
 	/* bubble the new value up the tree as required.
 	 */
 	for (k = 0; k < le32_to_cpu(tp->dmt_height); k++) {
+		if (lp == 0)
+			break;
+
 		/* get the index of the first leaf of the 4 leaf
 		 * group containing the specified leaf (leafno).
 		 */
@@ -2955,14 +3009,19 @@
  *	leafidx	- return pointer to be set to the index of the leaf
  *		  describing at least l2nb free blocks if sufficient
  *		  free blocks are found.
+ *	is_ctl	- determines if the tree is of type ctl
  *
  * RETURN VALUES:
  *	0	- success
  *	-ENOSPC	- insufficient free blocks.
  */
-static int dbFindLeaf(dmtree_t * tp, int l2nb, int *leafidx)
+static int dbFindLeaf(dmtree_t *tp, int l2nb, int *leafidx, bool is_ctl)
 {
 	int ti, n = 0, k, x = 0;
+	int max_size, max_idx;
+
+	max_size = is_ctl ? CTLTREESIZE : TREESIZE;
+	max_idx = is_ctl ? LPERCTL : LPERDMAP;
 
 	/* first check the root of the tree to see if there is
 	 * sufficient free space.
@@ -2983,6 +3042,8 @@
 			/* sufficient free space found.  move to the next
 			 * level (or quit if this is the last level).
 			 */
+			if (x + n > max_size)
+				return -ENOSPC;
 			if (l2nb <= tp->dmt_stree[x + n])
 				break;
 		}
@@ -2992,6 +3053,8 @@
 		 */
 		assert(n < 4);
 	}
+	if (le32_to_cpu(tp->dmt_leafidx) >= max_idx)
+		return -ENOSPC;
 
 	/* set the return to the leftmost leaf describing sufficient
 	 * free space.
@@ -3036,7 +3099,7 @@
 
 	/* scan the word for nb free bits at nb alignments.
 	 */
-	for (bitno = 0; mask != 0; bitno += nb, mask >>= nb) {
+	for (bitno = 0; mask != 0; bitno += nb, mask = (mask >> nb)) {
 		if ((mask & word) == mask)
 			break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_dtree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_dtree.c
@@ -117,7 +117,8 @@
 	if (!(RC)) {							\
 		if (((P)->header.nextindex >				\
 		     (((BN) == 0) ? DTROOTMAXSLOT : (P)->header.maxslot)) || \
-		    ((BN) && ((P)->header.maxslot > DTPAGEMAXSLOT))) {	\
+		    ((BN) && (((P)->header.maxslot > DTPAGEMAXSLOT) ||	\
+		    ((P)->header.stblindex >= DTPAGEMAXSLOT)))) {	\
 			BT_PUTPAGE(MP);					\
 			jfs_error((IP)->i_sb,				\
 				  "DT_GETPAGE: dtree page corrupt\n");	\
@@ -633,6 +634,11 @@
 		for (base = 0, lim = p->header.nextindex; lim; lim >>= 1) {
 			index = base + (lim >> 1);
 
+			if (stbl[index] < 0) {
+				rc = -EIO;
+				goto out;
+			}
+
 			if (p->header.flag & BT_LEAF) {
 				/* uppercase leaf name to compare */
 				cmp =
@@ -1970,7 +1976,7 @@
 		do {
 			f = &rp->slot[fsi];
 			fsi = f->next;
-		} while (fsi != -1);
+		} while (fsi >= 0);
 
 		f->next = n;
 	}
@@ -3182,6 +3188,14 @@
 		stbl = DT_GETSTBL(p);
 
 		for (i = index; i < p->header.nextindex; i++) {
+			if (stbl[i] < 0 || stbl[i] > 127) {
+				jfs_err("JFS: Invalid stbl[%d] = %d for inode %ld, block = %lld",
+					i, stbl[i], (long)ip->i_ino, (long long)bn);
+				free_page(dirent_buf);
+				DT_PUTPAGE(mp);
+				return -EIO;
+			}
+
 			d = (struct ldtentry *) & p->slot[stbl[i]];
 
 			if (((long) jfs_dirent + d->namlen + 1) >
@@ -3377,6 +3391,13 @@
 
 		/* get the leftmost entry */
 		stbl = DT_GETSTBL(p);
+
+		if (stbl[0] < 0 || stbl[0] > 127) {
+			DT_PUTPAGE(mp);
+			jfs_error(ip->i_sb, "stbl[0] out of bound\n");
+			return -EIO;
+		}
+
 		xd = (pxd_t *) & p->slot[stbl[0]];
 
 		/* get the child page block address */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_extent.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_extent.c
@@ -508,6 +508,11 @@
 	 * blocks in the map. in that case, we'll start off with the
 	 * maximum free.
 	 */
+
+	/* give up if no space left */
+	if (bmp->db_maxfreebud == -1)
+		return -ENOSPC;
+
 	max = (s64) 1 << bmp->db_maxfreebud;
 	if (*nblocks >= max && *nblocks > nbperpage)
 		nb = nblks = (max > nbperpage) ? max : nbperpage;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_filsys.h
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_filsys.h
@@ -122,7 +122,9 @@
 #define NUM_INODE_PER_IAG	INOSPERIAG
 
 #define MINBLOCKSIZE		512
+#define L2MINBLOCKSIZE		9
 #define MAXBLOCKSIZE		4096
+#define L2MAXBLOCKSIZE		12
 #define	MAXFILESIZE		((s64)1 << 52)
 
 #define JFS_LINK_MAX		0xffffffff
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_imap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_imap.c
@@ -193,6 +193,7 @@
 	 * free in-memory control structure
 	 */
 	kfree(imap);
+	JFS_IP(ipimap)->i_imap = NULL;
 
 	return (0);
 }
@@ -289,7 +290,7 @@
 int diRead(struct inode *ip)
 {
 	struct jfs_sb_info *sbi = JFS_SBI(ip->i_sb);
-	int iagno, ino, extno, rc;
+	int iagno, ino, extno, rc, agno;
 	struct inode *ipimap;
 	struct dinode *dp;
 	struct iag *iagp;
@@ -338,8 +339,11 @@
 
 	/* get the ag for the iag */
 	agstart = le64_to_cpu(iagp->agstart);
+	agno = BLKTOAG(agstart, JFS_SBI(ip->i_sb));
 
 	release_metapage(mp);
+	if (agno >= MAXAG || agno < 0)
+		return -EIO;
 
 	rel_inode = (ino & (INOSPERPAGE - 1));
 	pageno = blkno >> sbi->l2nbperpage;
@@ -1319,7 +1323,7 @@
 int diAlloc(struct inode *pip, bool dir, struct inode *ip)
 {
 	int rc, ino, iagno, addext, extno, bitno, sword;
-	int nwords, rem, i, agno;
+	int nwords, rem, i, agno, dn_numag;
 	u32 mask, inosmap, extsmap;
 	struct inode *ipimap;
 	struct metapage *mp;
@@ -1355,6 +1359,9 @@
 
 	/* get the ag number of this iag */
 	agno = BLKTOAG(JFS_IP(pip)->agstart, JFS_SBI(pip->i_sb));
+	dn_numag = JFS_SBI(pip->i_sb)->bmap->db_numag;
+	if (agno < 0 || agno > dn_numag || agno >= MAXAG)
+		return -EIO;
 
 	if (atomic_read(&JFS_SBI(pip->i_sb)->bmap->db_active[agno])) {
 		/*
@@ -2175,6 +2182,9 @@
 	/* get the ag and iag numbers for this iag.
 	 */
 	agno = BLKTOAG(le64_to_cpu(iagp->agstart), sbi);
+	if (agno >= MAXAG || agno < 0)
+		return -EIO;
+
 	iagno = le32_to_cpu(iagp->iagnum);
 
 	/* check if this is the last free extent within the
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_mount.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_mount.c
@@ -81,14 +81,14 @@
 	 * (initialize mount inode from the superblock)
 	 */
 	if ((rc = chkSuper(sb))) {
-		goto errout20;
+		goto out;
 	}
 
 	ipaimap = diReadSpecial(sb, AGGREGATE_I, 0);
 	if (ipaimap == NULL) {
 		jfs_err("jfs_mount: Failed to read AGGREGATE_I");
 		rc = -EIO;
-		goto errout20;
+		goto out;
 	}
 	sbi->ipaimap = ipaimap;
 
@@ -99,7 +99,7 @@
 	 */
 	if ((rc = diMount(ipaimap))) {
 		jfs_err("jfs_mount: diMount(ipaimap) failed w/rc = %d", rc);
-		goto errout21;
+		goto err_ipaimap;
 	}
 
 	/*
@@ -108,7 +108,7 @@
 	ipbmap = diReadSpecial(sb, BMAP_I, 0);
 	if (ipbmap == NULL) {
 		rc = -EIO;
-		goto errout22;
+		goto err_umount_ipaimap;
 	}
 
 	jfs_info("jfs_mount: ipbmap:0x%p", ipbmap);
@@ -120,7 +120,7 @@
 	 */
 	if ((rc = dbMount(ipbmap))) {
 		jfs_err("jfs_mount: dbMount failed w/rc = %d", rc);
-		goto errout22;
+		goto err_ipbmap;
 	}
 
 	/*
@@ -139,7 +139,7 @@
 		if (!ipaimap2) {
 			jfs_err("jfs_mount: Failed to read AGGREGATE_I");
 			rc = -EIO;
-			goto errout35;
+			goto err_umount_ipbmap;
 		}
 		sbi->ipaimap2 = ipaimap2;
 
@@ -151,7 +151,7 @@
 		if ((rc = diMount(ipaimap2))) {
 			jfs_err("jfs_mount: diMount(ipaimap2) failed, rc = %d",
 				rc);
-			goto errout35;
+			goto err_ipaimap2;
 		}
 	} else
 		/* Secondary aggregate inode table is not valid */
@@ -168,51 +168,44 @@
 		jfs_err("jfs_mount: Failed to read FILESYSTEM_I");
 		/* open fileset secondary inode allocation map */
 		rc = -EIO;
-		goto errout40;
+		goto err_umount_ipaimap2;
 	}
 	jfs_info("jfs_mount: ipimap:0x%p", ipimap);
 
-	/* map further access of per fileset inodes by the fileset inode */
-	sbi->ipimap = ipimap;
-
 	/* initialize fileset inode allocation map */
 	if ((rc = diMount(ipimap))) {
 		jfs_err("jfs_mount: diMount failed w/rc = %d", rc);
-		goto errout41;
+		goto err_ipimap;
 	}
 
-	goto out;
+	/* map further access of per fileset inodes by the fileset inode */
+	sbi->ipimap = ipimap;
+
+	return rc;
 
 	/*
 	 *	unwind on error
 	 */
-      errout41:		/* close fileset inode allocation map inode */
+err_ipimap:
+	/* close fileset inode allocation map inode */
 	diFreeSpecial(ipimap);
-
-      errout40:		/* fileset closed */
-
+err_umount_ipaimap2:
 	/* close secondary aggregate inode allocation map */
-	if (ipaimap2) {
+	if (ipaimap2)
 		diUnmount(ipaimap2, 1);
+err_ipaimap2:
+	/* close aggregate inodes */
+	if (ipaimap2)
 		diFreeSpecial(ipaimap2);
-	}
-
-      errout35:
-
-	/* close aggregate block allocation map */
+err_umount_ipbmap:	/* close aggregate block allocation map */
 	dbUnmount(ipbmap, 1);
+err_ipbmap:		/* close aggregate inodes */
 	diFreeSpecial(ipbmap);
-
-      errout22:		/* close aggregate inode allocation map */
-
+err_umount_ipaimap:	/* close aggregate inode allocation map */
 	diUnmount(ipaimap, 1);
-
-      errout21:		/* close aggregate inodes */
+err_ipaimap:		/* close aggregate inodes */
 	diFreeSpecial(ipaimap);
-      errout20:		/* aggregate closed */
-
-      out:
-
+out:
 	if (rc)
 		jfs_err("Mount JFS Failure: %d", rc);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/jfs_txnmgr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/jfs_txnmgr.c
@@ -354,6 +354,11 @@
 	jfs_info("txBegin: flag = 0x%x", flag);
 	log = JFS_SBI(sb)->log;
 
+	if (!log) {
+		jfs_error(sb, "read-only filesystem\n");
+		return 0;
+	}
+
 	TXN_LOCK();
 
 	INCREMENT(TxStat.txBegin);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/namei.c
@@ -799,6 +799,11 @@
 	if (rc)
 		goto out;
 
+	if (isReadOnly(ip)) {
+		jfs_error(ip->i_sb, "read-only filesystem\n");
+		return -EROFS;
+	}
+
 	tid = txBegin(ip->i_sb, 0);
 
 	mutex_lock_nested(&JFS_IP(dir)->commit_mutex, COMMIT_MUTEX_PARENT);
@@ -946,7 +951,7 @@
 	if (ssize <= IDATASIZE) {
 		ip->i_op = &jfs_fast_symlink_inode_operations;
 
-		ip->i_link = JFS_IP(ip)->i_inline;
+		ip->i_link = JFS_IP(ip)->i_inline_all;
 		memcpy(ip->i_link, name, ssize);
 		ip->i_size = ssize - 1;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/jfs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/jfs/xattr.c
@@ -434,6 +434,8 @@
 	int rc;
 	int quota_allocation = 0;
 
+	memset(&ea_buf->new_ea, 0, sizeof(ea_buf->new_ea));
+
 	/* When fsck.jfs clears a bad ea, it doesn't clear the size */
 	if (ji->ea.flag == 0)
 		ea_size = 0;
@@ -557,9 +559,16 @@
 
       size_check:
 	if (EALIST_SIZE(ea_buf->xattr) != ea_size) {
-		printk(KERN_ERR "ea_get: invalid extended attribute\n");
-		print_hex_dump(KERN_ERR, "", DUMP_PREFIX_ADDRESS, 16, 1,
-				     ea_buf->xattr, ea_size, 1);
+		if (unlikely(EALIST_SIZE(ea_buf->xattr) > INT_MAX)) {
+			printk(KERN_ERR "ea_get: extended attribute size too large: %u > INT_MAX\n",
+			       EALIST_SIZE(ea_buf->xattr));
+		} else {
+			int size = clamp_t(int, ea_size, 0, EALIST_SIZE(ea_buf->xattr));
+
+			printk(KERN_ERR "ea_get: invalid extended attribute\n");
+			print_hex_dump(KERN_ERR, "", DUMP_PREFIX_ADDRESS, 16, 1,
+				       ea_buf->xattr, size, 1);
+		}
 		ea_release(inode, ea_buf);
 		rc = -EIO;
 		goto clean_up;
@@ -795,7 +804,7 @@
 		       size_t buf_size)
 {
 	struct jfs_ea_list *ealist;
-	struct jfs_ea *ea;
+	struct jfs_ea *ea, *ealist_end;
 	struct ea_buffer ea_buf;
 	int xattr_size;
 	ssize_t size;
@@ -815,9 +824,16 @@
 		goto not_found;
 
 	ealist = (struct jfs_ea_list *) ea_buf.xattr;
+	ealist_end = END_EALIST(ealist);
 
 	/* Find the named attribute */
-	for (ea = FIRST_EA(ealist); ea < END_EALIST(ealist); ea = NEXT_EA(ea))
+	for (ea = FIRST_EA(ealist); ea < ealist_end; ea = NEXT_EA(ea)) {
+		if (unlikely(ea + 1 > ealist_end) ||
+		    unlikely(NEXT_EA(ea) > ealist_end)) {
+			size = -EUCLEAN;
+			goto release;
+		}
+
 		if ((namelen == ea->namelen) &&
 		    memcmp(name, ea->name, namelen) == 0) {
 			/* Found it */
@@ -832,6 +848,7 @@
 			memcpy(data, value, size);
 			goto release;
 		}
+	}
       not_found:
 	size = -ENODATA;
       release:
@@ -859,7 +876,7 @@
 	ssize_t size = 0;
 	int xattr_size;
 	struct jfs_ea_list *ealist;
-	struct jfs_ea *ea;
+	struct jfs_ea *ea, *ealist_end;
 	struct ea_buffer ea_buf;
 
 	down_read(&JFS_IP(inode)->xattr_sem);
@@ -874,9 +891,16 @@
 		goto release;
 
 	ealist = (struct jfs_ea_list *) ea_buf.xattr;
+	ealist_end = END_EALIST(ealist);
 
 	/* compute required size of list */
-	for (ea = FIRST_EA(ealist); ea < END_EALIST(ealist); ea = NEXT_EA(ea)) {
+	for (ea = FIRST_EA(ealist); ea < ealist_end; ea = NEXT_EA(ea)) {
+		if (unlikely(ea + 1 > ealist_end) ||
+		    unlikely(NEXT_EA(ea) > ealist_end)) {
+			size = -EUCLEAN;
+			goto release;
+		}
+
 		if (can_list(ea))
 			size += name_size(ea) + 1;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/kernfs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/kernfs/dir.c
@@ -19,7 +19,15 @@
 
 DECLARE_RWSEM(kernfs_rwsem);
 static DEFINE_SPINLOCK(kernfs_rename_lock);	/* kn->parent and ->name */
-static char kernfs_pr_cont_buf[PATH_MAX];	/* protected by rename_lock */
+/*
+ * Don't use rename_lock to piggy back on pr_cont_buf. We don't want to
+ * call pr_cont() while holding rename_lock. Because sometimes pr_cont()
+ * will perform wakeups when releasing console_sem. Holding rename_lock
+ * will introduce deadlock if the scheduler reads the kernfs_name in the
+ * wakeup path.
+ */
+static DEFINE_SPINLOCK(kernfs_pr_cont_lock);
+static char kernfs_pr_cont_buf[PATH_MAX];	/* protected by pr_cont_lock */
 static DEFINE_SPINLOCK(kernfs_idr_lock);	/* root->ino_idr */
 
 #define rb_to_kn(X) rb_entry((X), struct kernfs_node, rb)
@@ -230,12 +238,12 @@
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&kernfs_rename_lock, flags);
+	spin_lock_irqsave(&kernfs_pr_cont_lock, flags);
 
-	kernfs_name_locked(kn, kernfs_pr_cont_buf, sizeof(kernfs_pr_cont_buf));
+	kernfs_name(kn, kernfs_pr_cont_buf, sizeof(kernfs_pr_cont_buf));
 	pr_cont("%s", kernfs_pr_cont_buf);
 
-	spin_unlock_irqrestore(&kernfs_rename_lock, flags);
+	spin_unlock_irqrestore(&kernfs_pr_cont_lock, flags);
 }
 
 /**
@@ -249,10 +257,10 @@
 	unsigned long flags;
 	int sz;
 
-	spin_lock_irqsave(&kernfs_rename_lock, flags);
+	spin_lock_irqsave(&kernfs_pr_cont_lock, flags);
 
-	sz = kernfs_path_from_node_locked(kn, NULL, kernfs_pr_cont_buf,
-					  sizeof(kernfs_pr_cont_buf));
+	sz = kernfs_path_from_node(kn, NULL, kernfs_pr_cont_buf,
+				   sizeof(kernfs_pr_cont_buf));
 	if (sz < 0) {
 		pr_cont("(error)");
 		goto out;
@@ -266,7 +274,7 @@
 	pr_cont("%s", kernfs_pr_cont_buf);
 
 out:
-	spin_unlock_irqrestore(&kernfs_rename_lock, flags);
+	spin_unlock_irqrestore(&kernfs_pr_cont_lock, flags);
 }
 
 /**
@@ -629,7 +637,9 @@
 	return kn;
 
  err_out3:
+	spin_lock(&kernfs_idr_lock);
 	idr_remove(&root->ino_idr, (u32)kernfs_ino(kn));
+	spin_unlock(&kernfs_idr_lock);
  err_out2:
 	kmem_cache_free(kernfs_node_cache, kn);
  err_out1:
@@ -644,6 +654,18 @@
 {
 	struct kernfs_node *kn;
 
+	if (parent->mode & S_ISGID) {
+		/* this code block imitates inode_init_owner() for
+		 * kernfs
+		 */
+
+		if (parent->iattr)
+			gid = parent->iattr->ia_gid;
+
+		if (flags & KERNFS_DIR)
+			mode |= S_ISGID;
+	}
+
 	kn = __kernfs_new_node(kernfs_root(parent), parent,
 			       name, mode, uid, gid, flags);
 	if (kn) {
@@ -822,13 +844,12 @@
 
 	lockdep_assert_held_read(&kernfs_rwsem);
 
-	/* grab kernfs_rename_lock to piggy back on kernfs_pr_cont_buf */
-	spin_lock_irq(&kernfs_rename_lock);
+	spin_lock_irq(&kernfs_pr_cont_lock);
 
 	len = strlcpy(kernfs_pr_cont_buf, path, sizeof(kernfs_pr_cont_buf));
 
 	if (len >= sizeof(kernfs_pr_cont_buf)) {
-		spin_unlock_irq(&kernfs_rename_lock);
+		spin_unlock_irq(&kernfs_pr_cont_lock);
 		return NULL;
 	}
 
@@ -840,7 +861,7 @@
 		parent = kernfs_find_ns(parent, name, ns);
 	}
 
-	spin_unlock_irq(&kernfs_rename_lock);
+	spin_unlock_irq(&kernfs_pr_cont_lock);
 
 	return parent;
 }
@@ -1540,8 +1561,11 @@
 	down_write(&kernfs_rwsem);
 
 	kn = kernfs_find_ns(parent, name, ns);
-	if (kn)
+	if (kn) {
+		kernfs_get(kn);
 		__kernfs_remove(kn);
+		kernfs_put(kn);
+	}
 
 	up_write(&kernfs_rwsem);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/Kconfig
@@ -1,12 +1,11 @@
 config SMB_SERVER
-	tristate "SMB3 server support (EXPERIMENTAL)"
+	tristate "SMB3 server support"
 	depends on INET
 	depends on MULTIUSER
 	depends on FILE_LOCKING
 	select NLS
 	select NLS_UTF8
 	select CRYPTO
-	select CRYPTO_MD4
 	select CRYPTO_MD5
 	select CRYPTO_HMAC
 	select CRYPTO_ECB
@@ -19,6 +18,7 @@
 	select CRYPTO_GCM
 	select ASN1
 	select OID_REGISTRY
+	select CRC32
 	default n
 	help
 	  Choose Y here if you want to allow SMB3 compliant clients
@@ -33,14 +33,16 @@
 	  in ksmbd-tools, available from
 	  https://github.com/cifsd-team/ksmbd-tools.
 	  More detail about how to run the ksmbd kernel server is
-	  available via README file
+	  available via the README file
 	  (https://github.com/cifsd-team/ksmbd-tools/blob/master/README).
 
 	  ksmbd kernel server includes support for auto-negotiation,
 	  Secure negotiate, Pre-authentication integrity, oplock/lease,
 	  compound requests, multi-credit, packet signing, RDMA(smbdirect),
 	  smb3 encryption, copy-offload, secure per-user session
-	  establishment via NTLM or NTLMv2.
+	  establishment via Kerberos or NTLMv2.
+
+if SMB_SERVER
 
 config SMB_SERVER_SMBDIRECT
 	bool "Support for SMB Direct protocol"
@@ -54,6 +56,8 @@
 	  SMB Direct allows transferring SMB packets over RDMA. If unsure,
 	  say N.
 
+endif
+
 config SMB_SERVER_CHECK_CAP_NET_ADMIN
 	bool "Enable check network administration capability"
 	depends on SMB_SERVER
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/asn1.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/asn1.c
@@ -21,101 +21,11 @@
 #include "ksmbd_spnego_negtokeninit.asn1.h"
 #include "ksmbd_spnego_negtokentarg.asn1.h"
 
-#define SPNEGO_OID_LEN 7
 #define NTLMSSP_OID_LEN  10
-#define KRB5_OID_LEN  7
-#define KRB5U2U_OID_LEN  8
-#define MSKRB5_OID_LEN  7
-static unsigned long SPNEGO_OID[7] = { 1, 3, 6, 1, 5, 5, 2 };
-static unsigned long NTLMSSP_OID[10] = { 1, 3, 6, 1, 4, 1, 311, 2, 2, 10 };
-static unsigned long KRB5_OID[7] = { 1, 2, 840, 113554, 1, 2, 2 };
-static unsigned long KRB5U2U_OID[8] = { 1, 2, 840, 113554, 1, 2, 2, 3 };
-static unsigned long MSKRB5_OID[7] = { 1, 2, 840, 48018, 1, 2, 2 };
 
 static char NTLMSSP_OID_STR[NTLMSSP_OID_LEN] = { 0x2b, 0x06, 0x01, 0x04, 0x01,
 	0x82, 0x37, 0x02, 0x02, 0x0a };
 
-static bool
-asn1_subid_decode(const unsigned char **begin, const unsigned char *end,
-		  unsigned long *subid)
-{
-	const unsigned char *ptr = *begin;
-	unsigned char ch;
-
-	*subid = 0;
-
-	do {
-		if (ptr >= end)
-			return false;
-
-		ch = *ptr++;
-		*subid <<= 7;
-		*subid |= ch & 0x7F;
-	} while ((ch & 0x80) == 0x80);
-
-	*begin = ptr;
-	return true;
-}
-
-static bool asn1_oid_decode(const unsigned char *value, size_t vlen,
-			    unsigned long **oid, size_t *oidlen)
-{
-	const unsigned char *iptr = value, *end = value + vlen;
-	unsigned long *optr;
-	unsigned long subid;
-
-	vlen += 1;
-	if (vlen < 2 || vlen > UINT_MAX / sizeof(unsigned long))
-		goto fail_nullify;
-
-	*oid = kmalloc(vlen * sizeof(unsigned long), GFP_KERNEL);
-	if (!*oid)
-		return false;
-
-	optr = *oid;
-
-	if (!asn1_subid_decode(&iptr, end, &subid))
-		goto fail;
-
-	if (subid < 40) {
-		optr[0] = 0;
-		optr[1] = subid;
-	} else if (subid < 80) {
-		optr[0] = 1;
-		optr[1] = subid - 40;
-	} else {
-		optr[0] = 2;
-		optr[1] = subid - 80;
-	}
-
-	*oidlen = 2;
-	optr += 2;
-
-	while (iptr < end) {
-		if (++(*oidlen) > vlen)
-			goto fail;
-
-		if (!asn1_subid_decode(&iptr, end, optr++))
-			goto fail;
-	}
-	return true;
-
-fail:
-	kfree(*oid);
-fail_nullify:
-	*oid = NULL;
-	return false;
-}
-
-static bool oid_eq(unsigned long *oid1, unsigned int oid1len,
-		   unsigned long *oid2, unsigned int oid2len)
-{
-	if (oid1len != oid2len)
-		return false;
-
-	return memcmp(oid1, oid2, oid1len) == 0;
-}
-
 int
 ksmbd_decode_negTokenInit(unsigned char *security_blob, int length,
 			  struct ksmbd_conn *conn)
@@ -252,26 +162,18 @@
 int ksmbd_gssapi_this_mech(void *context, size_t hdrlen, unsigned char tag,
 			   const void *value, size_t vlen)
 {
-	unsigned long *oid;
-	size_t oidlen;
-	int err = 0;
-
-	if (!asn1_oid_decode(value, vlen, &oid, &oidlen)) {
-		err = -EBADMSG;
-		goto out;
-	}
+	enum OID oid;
 
-	if (!oid_eq(oid, oidlen, SPNEGO_OID, SPNEGO_OID_LEN))
-		err = -EBADMSG;
-	kfree(oid);
-out:
-	if (err) {
+	oid = look_up_OID(value, vlen);
+	if (oid != OID_spnego) {
 		char buf[50];
 
 		sprint_oid(value, vlen, buf, sizeof(buf));
 		ksmbd_debug(AUTH, "Unexpected OID: %s\n", buf);
+		return -EBADMSG;
 	}
-	return err;
+
+	return 0;
 }
 
 int ksmbd_neg_token_init_mech_type(void *context, size_t hdrlen,
@@ -279,65 +181,61 @@
 				   size_t vlen)
 {
 	struct ksmbd_conn *conn = context;
-	unsigned long *oid;
-	size_t oidlen;
+	enum OID oid;
 	int mech_type;
-	char buf[50];
-
-	if (!asn1_oid_decode(value, vlen, &oid, &oidlen))
-		goto fail;
 
-	if (oid_eq(oid, oidlen, NTLMSSP_OID, NTLMSSP_OID_LEN))
+	oid = look_up_OID(value, vlen);
+	if (oid == OID_ntlmssp) {
 		mech_type = KSMBD_AUTH_NTLMSSP;
-	else if (oid_eq(oid, oidlen, MSKRB5_OID, MSKRB5_OID_LEN))
+	} else if (oid == OID_mskrb5) {
 		mech_type = KSMBD_AUTH_MSKRB5;
-	else if (oid_eq(oid, oidlen, KRB5_OID, KRB5_OID_LEN))
+	} else if (oid == OID_krb5) {
 		mech_type = KSMBD_AUTH_KRB5;
-	else if (oid_eq(oid, oidlen, KRB5U2U_OID, KRB5U2U_OID_LEN))
+	} else if (oid == OID_krb5u2u) {
 		mech_type = KSMBD_AUTH_KRB5U2U;
-	else
-		goto fail;
+	} else {
+		char buf[50];
+
+		sprint_oid(value, vlen, buf, sizeof(buf));
+		ksmbd_debug(AUTH, "Unexpected OID: %s\n", buf);
+		return -EBADMSG;
+	}
 
 	conn->auth_mechs |= mech_type;
 	if (conn->preferred_auth_mech == 0)
 		conn->preferred_auth_mech = mech_type;
 
-	kfree(oid);
 	return 0;
-
-fail:
-	kfree(oid);
-	sprint_oid(value, vlen, buf, sizeof(buf));
-	ksmbd_debug(AUTH, "Unexpected OID: %s\n", buf);
-	return -EBADMSG;
 }
 
-int ksmbd_neg_token_init_mech_token(void *context, size_t hdrlen,
-				    unsigned char tag, const void *value,
-				    size_t vlen)
+static int ksmbd_neg_token_alloc(void *context, size_t hdrlen,
+				 unsigned char tag, const void *value,
+				 size_t vlen)
 {
 	struct ksmbd_conn *conn = context;
 
-	conn->mechToken = kmalloc(vlen + 1, GFP_KERNEL);
+	if (!vlen)
+		return -EINVAL;
+
+	conn->mechToken = kmemdup_nul(value, vlen, GFP_KERNEL);
 	if (!conn->mechToken)
 		return -ENOMEM;
 
-	memcpy(conn->mechToken, value, vlen);
-	conn->mechToken[vlen] = '\0';
+	conn->mechTokenLen = (unsigned int)vlen;
+
 	return 0;
 }
 
-int ksmbd_neg_token_targ_resp_token(void *context, size_t hdrlen,
+int ksmbd_neg_token_init_mech_token(void *context, size_t hdrlen,
 				    unsigned char tag, const void *value,
 				    size_t vlen)
 {
-	struct ksmbd_conn *conn = context;
-
-	conn->mechToken = kmalloc(vlen + 1, GFP_KERNEL);
-	if (!conn->mechToken)
-		return -ENOMEM;
+	return ksmbd_neg_token_alloc(context, hdrlen, tag, value, vlen);
+}
 
-	memcpy(conn->mechToken, value, vlen);
-	conn->mechToken[vlen] = '\0';
-	return 0;
+int ksmbd_neg_token_targ_resp_token(void *context, size_t hdrlen,
+				    unsigned char tag, const void *value,
+				    size_t vlen)
+{
+	return ksmbd_neg_token_alloc(context, hdrlen, tag, value, vlen);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/auth.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/auth.c
@@ -29,6 +29,7 @@
 #include "mgmt/user_config.h"
 #include "crypto_ctx.h"
 #include "transport_ipc.h"
+#include "../smbfs_common/arc4.h"
 
 /*
  * Fixed format data defining GSS header and fixed string
@@ -120,8 +121,8 @@
 	return rc;
 }
 
-static int calc_ntlmv2_hash(struct ksmbd_session *sess, char *ntlmv2_hash,
-			    char *dname)
+static int calc_ntlmv2_hash(struct ksmbd_conn *conn, struct ksmbd_session *sess,
+			    char *ntlmv2_hash, char *dname)
 {
 	int ret, len, conv_len;
 	wchar_t *domain = NULL;
@@ -157,7 +158,7 @@
 	}
 
 	conv_len = smb_strtoUTF16(uniname, user_name(sess->user), len,
-				  sess->conn->local_nls);
+				  conn->local_nls);
 	if (conv_len < 0 || conv_len > len) {
 		ret = -EINVAL;
 		goto out;
@@ -181,7 +182,7 @@
 	}
 
 	conv_len = smb_strtoUTF16((__le16 *)domain, dname, len,
-				  sess->conn->local_nls);
+				  conn->local_nls);
 	if (conv_len < 0 || conv_len > len) {
 		ret = -EINVAL;
 		goto out;
@@ -214,27 +215,28 @@
  *
  * Return:	0 on success, error number on error
  */
-int ksmbd_auth_ntlmv2(struct ksmbd_session *sess, struct ntlmv2_resp *ntlmv2,
-		      int blen, char *domain_name)
+int ksmbd_auth_ntlmv2(struct ksmbd_conn *conn, struct ksmbd_session *sess,
+		      struct ntlmv2_resp *ntlmv2, int blen, char *domain_name,
+		      char *cryptkey)
 {
 	char ntlmv2_hash[CIFS_ENCPWD_SIZE];
 	char ntlmv2_rsp[CIFS_HMAC_MD5_HASH_SIZE];
-	struct ksmbd_crypto_ctx *ctx;
+	struct ksmbd_crypto_ctx *ctx = NULL;
 	char *construct = NULL;
 	int rc, len;
 
+	rc = calc_ntlmv2_hash(conn, sess, ntlmv2_hash, domain_name);
+	if (rc) {
+		ksmbd_debug(AUTH, "could not get v2 hash rc %d\n", rc);
+		goto out;
+	}
+
 	ctx = ksmbd_crypto_ctx_find_hmacmd5();
 	if (!ctx) {
 		ksmbd_debug(AUTH, "could not crypto alloc hmacmd5\n");
 		return -ENOMEM;
 	}
 
-	rc = calc_ntlmv2_hash(sess, ntlmv2_hash, domain_name);
-	if (rc) {
-		ksmbd_debug(AUTH, "could not get v2 hash rc %d\n", rc);
-		goto out;
-	}
-
 	rc = crypto_shash_setkey(CRYPTO_HMACMD5_TFM(ctx),
 				 ntlmv2_hash,
 				 CIFS_HMAC_MD5_HASH_SIZE);
@@ -256,7 +258,7 @@
 		goto out;
 	}
 
-	memcpy(construct, sess->ntlmssp.cryptkey, CIFS_CRYPTO_KEY_SIZE);
+	memcpy(construct, cryptkey, CIFS_CRYPTO_KEY_SIZE);
 	memcpy(construct + CIFS_CRYPTO_KEY_SIZE, &ntlmv2->blob_signature, blen);
 
 	rc = crypto_shash_update(CRYPTO_HMACMD5(ctx), construct, len);
@@ -270,6 +272,8 @@
 		ksmbd_debug(AUTH, "Could not generate md5 hash\n");
 		goto out;
 	}
+	ksmbd_release_crypto_ctx(ctx);
+	ctx = NULL;
 
 	rc = ksmbd_gen_sess_key(sess, ntlmv2_hash, ntlmv2_rsp);
 	if (rc) {
@@ -280,7 +284,8 @@
 	if (memcmp(ntlmv2->ntlmv2_hash, ntlmv2_rsp, CIFS_HMAC_MD5_HASH_SIZE) != 0)
 		rc = -EINVAL;
 out:
-	ksmbd_release_crypto_ctx(ctx);
+	if (ctx)
+		ksmbd_release_crypto_ctx(ctx);
 	kfree(construct);
 	return rc;
 }
@@ -295,7 +300,8 @@
  * Return:	0 on success, error number on error
  */
 int ksmbd_decode_ntlmssp_auth_blob(struct authenticate_message *authblob,
-				   int blob_len, struct ksmbd_session *sess)
+				   int blob_len, struct ksmbd_conn *conn,
+				   struct ksmbd_session *sess)
 {
 	char *domain_name;
 	unsigned int nt_off, dn_off;
@@ -319,22 +325,50 @@
 	dn_off = le32_to_cpu(authblob->DomainName.BufferOffset);
 	dn_len = le16_to_cpu(authblob->DomainName.Length);
 
-	if (blob_len < (u64)dn_off + dn_len || blob_len < (u64)nt_off + nt_len)
+	if (blob_len < (u64)dn_off + dn_len || blob_len < (u64)nt_off + nt_len ||
+	    nt_len < CIFS_ENCPWD_SIZE)
 		return -EINVAL;
 
 	/* TODO : use domain name that imported from configuration file */
 	domain_name = smb_strndup_from_utf16((const char *)authblob + dn_off,
-					     dn_len, true, sess->conn->local_nls);
+					     dn_len, true, conn->local_nls);
 	if (IS_ERR(domain_name))
 		return PTR_ERR(domain_name);
 
 	/* process NTLMv2 authentication */
 	ksmbd_debug(AUTH, "decode_ntlmssp_authenticate_blob dname%s\n",
 		    domain_name);
-	ret = ksmbd_auth_ntlmv2(sess, (struct ntlmv2_resp *)((char *)authblob + nt_off),
+	ret = ksmbd_auth_ntlmv2(conn, sess,
+				(struct ntlmv2_resp *)((char *)authblob + nt_off),
 				nt_len - CIFS_ENCPWD_SIZE,
-				domain_name);
+				domain_name, conn->ntlmssp.cryptkey);
 	kfree(domain_name);
+
+	/* The recovered secondary session key */
+	if (conn->ntlmssp.client_flags & NTLMSSP_NEGOTIATE_KEY_XCH) {
+		struct arc4_ctx *ctx_arc4;
+		unsigned int sess_key_off, sess_key_len;
+
+		sess_key_off = le32_to_cpu(authblob->SessionKey.BufferOffset);
+		sess_key_len = le16_to_cpu(authblob->SessionKey.Length);
+
+		if (blob_len < (u64)sess_key_off + sess_key_len)
+			return -EINVAL;
+
+		if (sess_key_len > CIFS_KEY_SIZE)
+			return -EINVAL;
+
+		ctx_arc4 = kmalloc(sizeof(*ctx_arc4), GFP_KERNEL);
+		if (!ctx_arc4)
+			return -ENOMEM;
+
+		cifs_arc4_setkey(ctx_arc4, sess->sess_key,
+				 SMB2_NTLMV2_SESSKEY_SIZE);
+		cifs_arc4_crypt(ctx_arc4, sess->sess_key,
+				(char *)authblob + sess_key_off, sess_key_len);
+		kfree_sensitive(ctx_arc4);
+	}
+
 	return ret;
 }
 
@@ -347,7 +381,7 @@
  *
  */
 int ksmbd_decode_ntlmssp_neg_blob(struct negotiate_message *negblob,
-				  int blob_len, struct ksmbd_session *sess)
+				  int blob_len, struct ksmbd_conn *conn)
 {
 	if (blob_len < sizeof(struct negotiate_message)) {
 		ksmbd_debug(AUTH, "negotiate blob len %d too small\n",
@@ -361,7 +395,7 @@
 		return -EINVAL;
 	}
 
-	sess->ntlmssp.client_flags = le32_to_cpu(negblob->NegotiateFlags);
+	conn->ntlmssp.client_flags = le32_to_cpu(negblob->NegotiateFlags);
 	return 0;
 }
 
@@ -375,14 +409,14 @@
  */
 unsigned int
 ksmbd_build_ntlmssp_challenge_blob(struct challenge_message *chgblob,
-				   struct ksmbd_session *sess)
+				   struct ksmbd_conn *conn)
 {
 	struct target_info *tinfo;
 	wchar_t *name;
 	__u8 *target_name;
 	unsigned int flags, blob_off, blob_len, type, target_info_len = 0;
 	int len, uni_len, conv_len;
-	int cflags = sess->ntlmssp.client_flags;
+	int cflags = conn->ntlmssp.client_flags;
 
 	memcpy(chgblob->Signature, NTLMSSP_SIGNATURE, 8);
 	chgblob->MessageType = NtLmChallenge;
@@ -397,16 +431,22 @@
 				   NTLMSSP_NEGOTIATE_56);
 	}
 
+	if (cflags & NTLMSSP_NEGOTIATE_SEAL && smb3_encryption_negotiated(conn))
+		flags |= NTLMSSP_NEGOTIATE_SEAL;
+
 	if (cflags & NTLMSSP_NEGOTIATE_ALWAYS_SIGN)
 		flags |= NTLMSSP_NEGOTIATE_ALWAYS_SIGN;
 
 	if (cflags & NTLMSSP_REQUEST_TARGET)
 		flags |= NTLMSSP_REQUEST_TARGET;
 
-	if (sess->conn->use_spnego &&
+	if (conn->use_spnego &&
 	    (cflags & NTLMSSP_NEGOTIATE_EXTENDED_SEC))
 		flags |= NTLMSSP_NEGOTIATE_EXTENDED_SEC;
 
+	if (cflags & NTLMSSP_NEGOTIATE_KEY_XCH)
+		flags |= NTLMSSP_NEGOTIATE_KEY_XCH;
+
 	chgblob->NegotiateFlags = cpu_to_le32(flags);
 	len = strlen(ksmbd_netbios_name());
 	name = kmalloc(2 + UNICODE_LEN(len), GFP_KERNEL);
@@ -414,7 +454,7 @@
 		return -ENOMEM;
 
 	conv_len = smb_strtoUTF16((__le16 *)name, ksmbd_netbios_name(), len,
-				  sess->conn->local_nls);
+				  conn->local_nls);
 	if (conv_len < 0 || conv_len > len) {
 		kfree(name);
 		return -EINVAL;
@@ -430,8 +470,8 @@
 	chgblob->TargetName.BufferOffset = cpu_to_le32(blob_off);
 
 	/* Initialize random conn challenge */
-	get_random_bytes(sess->ntlmssp.cryptkey, sizeof(__u64));
-	memcpy(chgblob->Challenge, sess->ntlmssp.cryptkey,
+	get_random_bytes(conn->ntlmssp.cryptkey, sizeof(__u64));
+	memcpy(chgblob->Challenge, conn->ntlmssp.cryptkey,
 	       CIFS_CRYPTO_KEY_SIZE);
 
 	/* Add Target Information to security buffer */
@@ -631,8 +671,9 @@
 	bool binding;
 };
 
-static int generate_key(struct ksmbd_session *sess, struct kvec label,
-			struct kvec context, __u8 *key, unsigned int key_size)
+static int generate_key(struct ksmbd_conn *conn, struct ksmbd_session *sess,
+			struct kvec label, struct kvec context, __u8 *key,
+			unsigned int key_size)
 {
 	unsigned char zero = 0x0;
 	__u8 i[4] = {0, 0, 0, 1};
@@ -692,8 +733,9 @@
 		goto smb3signkey_ret;
 	}
 
-	if (sess->conn->cipher_type == SMB2_ENCRYPTION_AES256_CCM ||
-	    sess->conn->cipher_type == SMB2_ENCRYPTION_AES256_GCM)
+	if (key_size == SMB3_ENC_DEC_KEY_SIZE &&
+	    (conn->cipher_type == SMB2_ENCRYPTION_AES256_CCM ||
+	     conn->cipher_type == SMB2_ENCRYPTION_AES256_GCM))
 		rc = crypto_shash_update(CRYPTO_HMACSHA256(ctx), L256, 4);
 	else
 		rc = crypto_shash_update(CRYPTO_HMACSHA256(ctx), L128, 4);
@@ -728,17 +770,17 @@
 	if (!chann)
 		return 0;
 
-	if (sess->conn->dialect >= SMB30_PROT_ID && signing->binding)
+	if (conn->dialect >= SMB30_PROT_ID && signing->binding)
 		key = chann->smb3signingkey;
 	else
 		key = sess->smb3signingkey;
 
-	rc = generate_key(sess, signing->label, signing->context, key,
+	rc = generate_key(conn, sess, signing->label, signing->context, key,
 			  SMB3_SIGN_KEY_SIZE);
 	if (rc)
 		return rc;
 
-	if (!(sess->conn->dialect >= SMB30_PROT_ID && signing->binding))
+	if (!(conn->dialect >= SMB30_PROT_ID && signing->binding))
 		memcpy(chann->smb3signingkey, key, SMB3_SIGN_KEY_SIZE);
 
 	ksmbd_debug(AUTH, "dumping generated AES signing keys\n");
@@ -792,30 +834,31 @@
 	struct derivation decryption;
 };
 
-static int generate_smb3encryptionkey(struct ksmbd_session *sess,
+static int generate_smb3encryptionkey(struct ksmbd_conn *conn,
+				      struct ksmbd_session *sess,
 				      const struct derivation_twin *ptwin)
 {
 	int rc;
 
-	rc = generate_key(sess, ptwin->encryption.label,
+	rc = generate_key(conn, sess, ptwin->encryption.label,
 			  ptwin->encryption.context, sess->smb3encryptionkey,
 			  SMB3_ENC_DEC_KEY_SIZE);
 	if (rc)
 		return rc;
 
-	rc = generate_key(sess, ptwin->decryption.label,
+	rc = generate_key(conn, sess, ptwin->decryption.label,
 			  ptwin->decryption.context,
 			  sess->smb3decryptionkey, SMB3_ENC_DEC_KEY_SIZE);
 	if (rc)
 		return rc;
 
 	ksmbd_debug(AUTH, "dumping generated AES encryption keys\n");
-	ksmbd_debug(AUTH, "Cipher type   %d\n", sess->conn->cipher_type);
+	ksmbd_debug(AUTH, "Cipher type   %d\n", conn->cipher_type);
 	ksmbd_debug(AUTH, "Session Id    %llu\n", sess->id);
 	ksmbd_debug(AUTH, "Session Key   %*ph\n",
 		    SMB2_NTLMV2_SESSKEY_SIZE, sess->sess_key);
-	if (sess->conn->cipher_type == SMB2_ENCRYPTION_AES256_CCM ||
-	    sess->conn->cipher_type == SMB2_ENCRYPTION_AES256_GCM) {
+	if (conn->cipher_type == SMB2_ENCRYPTION_AES256_CCM ||
+	    conn->cipher_type == SMB2_ENCRYPTION_AES256_GCM) {
 		ksmbd_debug(AUTH, "ServerIn Key  %*ph\n",
 			    SMB3_GCM256_CRYPTKEY_SIZE, sess->smb3encryptionkey);
 		ksmbd_debug(AUTH, "ServerOut Key %*ph\n",
@@ -829,7 +872,8 @@
 	return 0;
 }
 
-int ksmbd_gen_smb30_encryptionkey(struct ksmbd_session *sess)
+int ksmbd_gen_smb30_encryptionkey(struct ksmbd_conn *conn,
+				  struct ksmbd_session *sess)
 {
 	struct derivation_twin twin;
 	struct derivation *d;
@@ -846,10 +890,11 @@
 	d->context.iov_base = "ServerIn ";
 	d->context.iov_len = 10;
 
-	return generate_smb3encryptionkey(sess, &twin);
+	return generate_smb3encryptionkey(conn, sess, &twin);
 }
 
-int ksmbd_gen_smb311_encryptionkey(struct ksmbd_session *sess)
+int ksmbd_gen_smb311_encryptionkey(struct ksmbd_conn *conn,
+				   struct ksmbd_session *sess)
 {
 	struct derivation_twin twin;
 	struct derivation *d;
@@ -866,16 +911,16 @@
 	d->context.iov_base = sess->Preauth_HashValue;
 	d->context.iov_len = 64;
 
-	return generate_smb3encryptionkey(sess, &twin);
+	return generate_smb3encryptionkey(conn, sess, &twin);
 }
 
 int ksmbd_gen_preauth_integrity_hash(struct ksmbd_conn *conn, char *buf,
 				     __u8 *pi_hash)
 {
 	int rc;
-	struct smb2_hdr *rcv_hdr = (struct smb2_hdr *)buf;
+	struct smb2_hdr *rcv_hdr = smb2_get_msg(buf);
 	char *all_bytes_msg = (char *)&rcv_hdr->ProtocolId;
-	int msg_size = be32_to_cpu(rcv_hdr->smb2_buf_length);
+	int msg_size = get_rfc1002_len(buf);
 	struct ksmbd_crypto_ctx *ctx = NULL;
 
 	if (conn->preauth_info->Preauth_HashId !=
@@ -950,18 +995,23 @@
 	return rc;
 }
 
-static int ksmbd_get_encryption_key(struct ksmbd_conn *conn, __u64 ses_id,
+static int ksmbd_get_encryption_key(struct ksmbd_work *work, __u64 ses_id,
 				    int enc, u8 *key)
 {
 	struct ksmbd_session *sess;
 	u8 *ses_enc_key;
 
-	sess = ksmbd_session_lookup_all(conn, ses_id);
+	if (enc)
+		sess = work->sess;
+	else
+		sess = ksmbd_session_lookup_all(work->conn, ses_id);
 	if (!sess)
 		return -EINVAL;
 
 	ses_enc_key = enc ? sess->smb3encryptionkey :
 		sess->smb3decryptionkey;
+	if (enc)
+		ksmbd_user_session_get(sess);
 	memcpy(key, ses_enc_key, SMB3_ENC_DEC_KEY_SIZE);
 
 	return 0;
@@ -983,12 +1033,16 @@
 					 u8 *sign)
 {
 	struct scatterlist *sg;
-	unsigned int assoc_data_len = sizeof(struct smb2_transform_hdr) - 24;
-	int i, nr_entries[3] = {0}, total_entries = 0, sg_idx = 0;
+	unsigned int assoc_data_len = sizeof(struct smb2_transform_hdr) - 20;
+	int i, *nr_entries, total_entries = 0, sg_idx = 0;
 
 	if (!nvec)
 		return NULL;
 
+	nr_entries = kcalloc(nvec, sizeof(int), GFP_KERNEL);
+	if (!nr_entries)
+		return NULL;
+
 	for (i = 0; i < nvec - 1; i++) {
 		unsigned long kaddr = (unsigned long)iov[i + 1].iov_base;
 
@@ -1006,8 +1060,10 @@
 	total_entries += 2;
 
 	sg = kmalloc_array(total_entries, sizeof(struct scatterlist), GFP_KERNEL);
-	if (!sg)
+	if (!sg) {
+		kfree(nr_entries);
 		return NULL;
+	}
 
 	sg_init_table(sg, total_entries);
 	smb2_sg_set_buf(&sg[sg_idx++], iov[0].iov_base + 24, assoc_data_len);
@@ -1041,15 +1097,16 @@
 		}
 	}
 	smb2_sg_set_buf(&sg[sg_idx], sign, SMB2_SIGNATURE_SIZE);
+	kfree(nr_entries);
 	return sg;
 }
 
-int ksmbd_crypt_message(struct ksmbd_conn *conn, struct kvec *iov,
+int ksmbd_crypt_message(struct ksmbd_work *work, struct kvec *iov,
 			unsigned int nvec, int enc)
 {
-	struct smb2_transform_hdr *tr_hdr =
-		(struct smb2_transform_hdr *)iov[0].iov_base;
-	unsigned int assoc_data_len = sizeof(struct smb2_transform_hdr) - 24;
+	struct ksmbd_conn *conn = work->conn;
+	struct smb2_transform_hdr *tr_hdr = smb2_get_msg(iov[0].iov_base);
+	unsigned int assoc_data_len = sizeof(struct smb2_transform_hdr) - 20;
 	int rc;
 	struct scatterlist *sg;
 	u8 sign[SMB2_SIGNATURE_SIZE] = {};
@@ -1061,7 +1118,7 @@
 	unsigned int crypt_len = le32_to_cpu(tr_hdr->OriginalMessageSize);
 	struct ksmbd_crypto_ctx *ctx;
 
-	rc = ksmbd_get_encryption_key(conn,
+	rc = ksmbd_get_encryption_key(work,
 				      le64_to_cpu(tr_hdr->SessionId),
 				      enc,
 				      key);
@@ -1154,7 +1211,7 @@
 free_sg:
 	kfree(sg);
 free_req:
-	kfree(req);
+	aead_request_free(req);
 free_ctx:
 	ksmbd_release_crypto_ctx(ctx);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/auth.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/auth.h
@@ -33,21 +33,23 @@
 
 struct ksmbd_session;
 struct ksmbd_conn;
+struct ksmbd_work;
 struct kvec;
 
-int ksmbd_crypt_message(struct ksmbd_conn *conn, struct kvec *iov,
+int ksmbd_crypt_message(struct ksmbd_work *work, struct kvec *iov,
 			unsigned int nvec, int enc);
 void ksmbd_copy_gss_neg_header(void *buf);
-int ksmbd_auth_ntlm(struct ksmbd_session *sess, char *pw_buf);
-int ksmbd_auth_ntlmv2(struct ksmbd_session *sess, struct ntlmv2_resp *ntlmv2,
-		      int blen, char *domain_name);
+int ksmbd_auth_ntlmv2(struct ksmbd_conn *conn, struct ksmbd_session *sess,
+		      struct ntlmv2_resp *ntlmv2, int blen, char *domain_name,
+		      char *cryptkey);
 int ksmbd_decode_ntlmssp_auth_blob(struct authenticate_message *authblob,
-				   int blob_len, struct ksmbd_session *sess);
+				   int blob_len, struct ksmbd_conn *conn,
+				   struct ksmbd_session *sess);
 int ksmbd_decode_ntlmssp_neg_blob(struct negotiate_message *negblob,
-				  int blob_len, struct ksmbd_session *sess);
+				  int blob_len, struct ksmbd_conn *conn);
 unsigned int
 ksmbd_build_ntlmssp_challenge_blob(struct challenge_message *chgblob,
-				   struct ksmbd_session *sess);
+				   struct ksmbd_conn *conn);
 int ksmbd_krb5_authenticate(struct ksmbd_session *sess, char *in_blob,
 			    int in_len,	char *out_blob, int *out_len);
 int ksmbd_sign_smb2_pdu(struct ksmbd_conn *conn, char *key, struct kvec *iov,
@@ -58,8 +60,10 @@
 			       struct ksmbd_conn *conn);
 int ksmbd_gen_smb311_signingkey(struct ksmbd_session *sess,
 				struct ksmbd_conn *conn);
-int ksmbd_gen_smb30_encryptionkey(struct ksmbd_session *sess);
-int ksmbd_gen_smb311_encryptionkey(struct ksmbd_session *sess);
+int ksmbd_gen_smb30_encryptionkey(struct ksmbd_conn *conn,
+				  struct ksmbd_session *sess);
+int ksmbd_gen_smb311_encryptionkey(struct ksmbd_conn *conn,
+				   struct ksmbd_session *sess);
 int ksmbd_gen_preauth_integrity_hash(struct ksmbd_conn *conn, char *buf,
 				     __u8 *pi_hash);
 int ksmbd_gen_sd_hash(struct ksmbd_conn *conn, char *sd_buf, int len,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/connection.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/connection.c
@@ -20,7 +20,7 @@
 static struct ksmbd_conn_ops default_conn_ops;
 
 LIST_HEAD(conn_list);
-DEFINE_RWLOCK(conn_list_lock);
+DECLARE_RWSEM(conn_list_lock);
 
 /**
  * ksmbd_conn_free() - free resources of the connection instance
@@ -32,10 +32,11 @@
  */
 void ksmbd_conn_free(struct ksmbd_conn *conn)
 {
-	write_lock(&conn_list_lock);
+	down_write(&conn_list_lock);
 	list_del(&conn->conns_list);
-	write_unlock(&conn_list_lock);
+	up_write(&conn_list_lock);
 
+	xa_destroy(&conn->sessions);
 	kvfree(conn->request_buf);
 	kfree(conn->preauth_info);
 	kfree(conn);
@@ -55,29 +56,39 @@
 		return NULL;
 
 	conn->need_neg = true;
-	conn->status = KSMBD_SESS_NEW;
+	ksmbd_conn_set_new(conn);
 	conn->local_nls = load_nls("utf8");
 	if (!conn->local_nls)
 		conn->local_nls = load_nls_default();
+	if (IS_ENABLED(CONFIG_UNICODE))
+		conn->um = utf8_load("12.1.0");
+	else
+		conn->um = ERR_PTR(-EOPNOTSUPP);
+	if (IS_ERR(conn->um))
+		conn->um = NULL;
 	atomic_set(&conn->req_running, 0);
 	atomic_set(&conn->r_count, 0);
 	conn->total_credits = 1;
+	conn->outstanding_credits = 0;
 
 	init_waitqueue_head(&conn->req_running_q);
+	init_waitqueue_head(&conn->r_count_q);
 	INIT_LIST_HEAD(&conn->conns_list);
-	INIT_LIST_HEAD(&conn->sessions);
 	INIT_LIST_HEAD(&conn->requests);
 	INIT_LIST_HEAD(&conn->async_requests);
 	spin_lock_init(&conn->request_lock);
 	spin_lock_init(&conn->credits_lock);
 	ida_init(&conn->async_ida);
+	xa_init(&conn->sessions);
 
 	spin_lock_init(&conn->llist_lock);
 	INIT_LIST_HEAD(&conn->lock_list);
 
-	write_lock(&conn_list_lock);
+	init_rwsem(&conn->session_lock);
+
+	down_write(&conn_list_lock);
 	list_add(&conn->conns_list, &conn_list);
-	write_unlock(&conn_list_lock);
+	up_write(&conn_list_lock);
 	return conn;
 }
 
@@ -86,7 +97,7 @@
 	struct ksmbd_conn *t;
 	bool ret = false;
 
-	read_lock(&conn_list_lock);
+	down_read(&conn_list_lock);
 	list_for_each_entry(t, &conn_list, conns_list) {
 		if (memcmp(t->ClientGUID, c->ClientGUID, SMB2_CLIENT_GUID_SIZE))
 			continue;
@@ -94,7 +105,7 @@
 		ret = true;
 		break;
 	}
-	read_unlock(&conn_list_lock);
+	up_read(&conn_list_lock);
 	return ret;
 }
 
@@ -103,10 +114,8 @@
 	struct ksmbd_conn *conn = work->conn;
 	struct list_head *requests_queue = NULL;
 
-	if (conn->ops->get_cmd_val(work) != SMB2_CANCEL_HE) {
+	if (conn->ops->get_cmd_val(work) != SMB2_CANCEL_HE)
 		requests_queue = &conn->requests;
-		work->syncronous = true;
-	}
 
 	if (requests_queue) {
 		atomic_inc(&conn->req_running);
@@ -116,41 +125,47 @@
 	}
 }
 
-int ksmbd_conn_try_dequeue_request(struct ksmbd_work *work)
+void ksmbd_conn_try_dequeue_request(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	int ret = 1;
 
 	if (list_empty(&work->request_entry) &&
 	    list_empty(&work->async_request_entry))
-		return 0;
+		return;
 
-	if (!work->multiRsp)
-		atomic_dec(&conn->req_running);
+	atomic_dec(&conn->req_running);
 	spin_lock(&conn->request_lock);
-	if (!work->multiRsp) {
-		list_del_init(&work->request_entry);
-		if (work->syncronous == false)
-			list_del_init(&work->async_request_entry);
-		ret = 0;
-	}
+	list_del_init(&work->request_entry);
 	spin_unlock(&conn->request_lock);
+	if (work->asynchronous)
+		release_async_work(work);
 
 	wake_up_all(&conn->req_running_q);
-	return ret;
 }
 
-static void ksmbd_conn_lock(struct ksmbd_conn *conn)
+void ksmbd_conn_lock(struct ksmbd_conn *conn)
 {
 	mutex_lock(&conn->srv_mutex);
 }
 
-static void ksmbd_conn_unlock(struct ksmbd_conn *conn)
+void ksmbd_conn_unlock(struct ksmbd_conn *conn)
 {
 	mutex_unlock(&conn->srv_mutex);
 }
 
-void ksmbd_conn_wait_idle(struct ksmbd_conn *conn)
+void ksmbd_all_conn_set_status(u64 sess_id, u32 status)
+{
+	struct ksmbd_conn *conn;
+
+	down_read(&conn_list_lock);
+	list_for_each_entry(conn, &conn_list, conns_list) {
+		if (conn->binding || xa_load(&conn->sessions, sess_id))
+			WRITE_ONCE(conn->status, status);
+	}
+	up_read(&conn_list_lock);
+}
+
+void ksmbd_conn_wait_idle(struct ksmbd_conn *conn, u64 sess_id)
 {
 	wait_event(conn->req_running_q, atomic_read(&conn->req_running) < 2);
 }
@@ -158,43 +173,25 @@
 int ksmbd_conn_write(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb_hdr *rsp_hdr = work->response_buf;
-	size_t len = 0;
 	int sent;
-	struct kvec iov[3];
-	int iov_idx = 0;
 
-	ksmbd_conn_try_dequeue_request(work);
-	if (!rsp_hdr) {
+	if (!work->response_buf) {
 		pr_err("NULL response header\n");
 		return -EINVAL;
 	}
 
-	if (work->tr_buf) {
-		iov[iov_idx] = (struct kvec) { work->tr_buf,
-				sizeof(struct smb2_transform_hdr) };
-		len += iov[iov_idx++].iov_len;
-	}
+	if (work->send_no_response)
+		return 0;
 
-	if (work->aux_payload_sz) {
-		iov[iov_idx] = (struct kvec) { rsp_hdr, work->resp_hdr_sz };
-		len += iov[iov_idx++].iov_len;
-		iov[iov_idx] = (struct kvec) { work->aux_payload_buf, work->aux_payload_sz };
-		len += iov[iov_idx++].iov_len;
-	} else {
-		if (work->tr_buf)
-			iov[iov_idx].iov_len = work->resp_hdr_sz;
-		else
-			iov[iov_idx].iov_len = get_rfc1002_len(rsp_hdr) + 4;
-		iov[iov_idx].iov_base = rsp_hdr;
-		len += iov[iov_idx++].iov_len;
-	}
+	if (!work->iov_idx)
+		return -EINVAL;
 
 	ksmbd_conn_lock(conn);
-	sent = conn->transport->ops->writev(conn->transport, &iov[0],
-					iov_idx, len,
-					work->need_invalidate_rkey,
-					work->remote_key);
+	sent = conn->transport->ops->writev(conn->transport, work->iov,
+			work->iov_cnt,
+			get_rfc1002_len(work->iov[0].iov_base) + 4,
+			work->need_invalidate_rkey,
+			work->remote_key);
 	ksmbd_conn_unlock(conn);
 
 	if (sent < 0) {
@@ -205,31 +202,31 @@
 	return 0;
 }
 
-int ksmbd_conn_rdma_read(struct ksmbd_conn *conn, void *buf,
-			 unsigned int buflen, u32 remote_key, u64 remote_offset,
-			 u32 remote_len)
+int ksmbd_conn_rdma_read(struct ksmbd_conn *conn,
+			 void *buf, unsigned int buflen,
+			 struct smb2_buffer_desc_v1 *desc,
+			 unsigned int desc_len)
 {
 	int ret = -EINVAL;
 
 	if (conn->transport->ops->rdma_read)
 		ret = conn->transport->ops->rdma_read(conn->transport,
 						      buf, buflen,
-						      remote_key, remote_offset,
-						      remote_len);
+						      desc, desc_len);
 	return ret;
 }
 
-int ksmbd_conn_rdma_write(struct ksmbd_conn *conn, void *buf,
-			  unsigned int buflen, u32 remote_key,
-			  u64 remote_offset, u32 remote_len)
+int ksmbd_conn_rdma_write(struct ksmbd_conn *conn,
+			  void *buf, unsigned int buflen,
+			  struct smb2_buffer_desc_v1 *desc,
+			  unsigned int desc_len)
 {
 	int ret = -EINVAL;
 
 	if (conn->transport->ops->rdma_write)
 		ret = conn->transport->ops->rdma_write(conn->transport,
 						       buf, buflen,
-						       remote_key, remote_offset,
-						       remote_len);
+						       desc, desc_len);
 	return ret;
 }
 
@@ -238,7 +235,7 @@
 	if (!ksmbd_server_running())
 		return false;
 
-	if (conn->status == KSMBD_SESS_EXITING)
+	if (ksmbd_conn_exiting(conn))
 		return false;
 
 	if (kthread_should_stop())
@@ -261,6 +258,9 @@
 	return true;
 }
 
+#define SMB1_MIN_SUPPORTED_HEADER_SIZE (sizeof(struct smb_hdr))
+#define SMB2_MIN_SUPPORTED_HEADER_SIZE (sizeof(struct smb2_hdr) + 4)
+
 /**
  * ksmbd_conn_handler_loop() - session thread to listen on new smb requests
  * @p:		connection instance
@@ -273,7 +273,7 @@
 {
 	struct ksmbd_conn *conn = (struct ksmbd_conn *)p;
 	struct ksmbd_transport *t = conn->transport;
-	unsigned int pdu_size;
+	unsigned int pdu_size, max_allowed_pdu_size;
 	char hdr_buf[4] = {0,};
 	int size;
 
@@ -284,6 +284,7 @@
 		goto out;
 
 	conn->last_active = jiffies;
+	set_freezable();
 	while (ksmbd_conn_alive(conn)) {
 		if (try_to_freeze())
 			continue;
@@ -291,37 +292,49 @@
 		kvfree(conn->request_buf);
 		conn->request_buf = NULL;
 
-		size = t->ops->read(t, hdr_buf, sizeof(hdr_buf));
+		size = t->ops->read(t, hdr_buf, sizeof(hdr_buf), -1);
 		if (size != sizeof(hdr_buf))
 			break;
 
 		pdu_size = get_rfc1002_len(hdr_buf);
 		ksmbd_debug(CONN, "RFC1002 header %u bytes\n", pdu_size);
 
+		if (ksmbd_conn_good(conn))
+			max_allowed_pdu_size =
+				SMB3_MAX_MSGSIZE + conn->vals->max_write_size;
+		else
+			max_allowed_pdu_size = SMB3_MAX_MSGSIZE;
+
+		if (pdu_size > max_allowed_pdu_size) {
+			pr_err_ratelimited("PDU length(%u) exceeded maximum allowed pdu size(%u) on connection(%d)\n",
+					pdu_size, max_allowed_pdu_size,
+					READ_ONCE(conn->status));
+			break;
+		}
+
 		/*
-		 * Check if pdu size is valid (min : smb header size,
-		 * max : 0x00FFFFFF).
+		 * Check maximum pdu size(0x00FFFFFF).
 		 */
-		if (pdu_size < __SMB2_HEADER_STRUCTURE_SIZE ||
-		    pdu_size > MAX_STREAM_PROT_LEN) {
-			continue;
-		}
+		if (pdu_size > MAX_STREAM_PROT_LEN)
+			break;
+
+		if (pdu_size < SMB1_MIN_SUPPORTED_HEADER_SIZE)
+			break;
 
 		/* 4 for rfc1002 length field */
-		size = pdu_size + 4;
+		/* 1 for implied bcc[0] */
+		size = pdu_size + 4 + 1;
 		conn->request_buf = kvmalloc(size, GFP_KERNEL);
 		if (!conn->request_buf)
-			continue;
+			break;
 
 		memcpy(conn->request_buf, hdr_buf, sizeof(hdr_buf));
-		if (!ksmbd_smb_request(conn))
-			break;
 
 		/*
 		 * We already read 4 bytes to find out PDU size, now
 		 * read in PDU
 		 */
-		size = t->ops->read(t, conn->request_buf + 4, pdu_size);
+		size = t->ops->read(t, conn->request_buf + 4, pdu_size, 2);
 		if (size < 0) {
 			pr_err("sock_read failed: %d\n", size);
 			break;
@@ -333,6 +346,15 @@
 			continue;
 		}
 
+		if (!ksmbd_smb_request(conn))
+			break;
+
+		if (((struct smb2_hdr *)smb2_get_msg(conn->request_buf))->ProtocolId ==
+		    SMB2_PROTO_NUMBER) {
+			if (pdu_size < SMB2_MIN_SUPPORTED_HEADER_SIZE)
+				break;
+		}
+
 		if (!default_conn_ops.process_fn) {
 			pr_err("No connection request callback\n");
 			break;
@@ -345,10 +367,12 @@
 	}
 
 out:
+	ksmbd_conn_set_releasing(conn);
 	/* Wait till all reference dropped to the Server object*/
-	while (atomic_read(&conn->r_count) > 0)
-		schedule_timeout(HZ);
+	wait_event(conn->r_count_q, atomic_read(&conn->r_count) == 0);
 
+	if (IS_ENABLED(CONFIG_UNICODE))
+		utf8_unload(conn->um);
 	unload_nls(conn->local_nls);
 	if (default_conn_ops.terminate_fn)
 		default_conn_ops.terminate_fn(conn);
@@ -387,19 +411,20 @@
 static void stop_sessions(void)
 {
 	struct ksmbd_conn *conn;
+	struct ksmbd_transport *t;
 
 again:
-	read_lock(&conn_list_lock);
+	down_read(&conn_list_lock);
 	list_for_each_entry(conn, &conn_list, conns_list) {
-		struct task_struct *task;
-
-		task = conn->transport->handler;
-		if (task)
-			ksmbd_debug(CONN, "Stop session handler %s/%d\n",
-				    task->comm, task_pid_nr(task));
-		conn->status = KSMBD_SESS_EXITING;
+		t = conn->transport;
+		ksmbd_conn_set_exiting(conn);
+		if (t->ops->shutdown) {
+			up_read(&conn_list_lock);
+			t->ops->shutdown(t);
+			down_read(&conn_list_lock);
+		}
 	}
-	read_unlock(&conn_list_lock);
+	up_read(&conn_list_lock);
 
 	if (!list_empty(&conn_list)) {
 		schedule_timeout_interruptible(HZ / 10); /* 100ms */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/connection.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/connection.h
@@ -14,25 +14,20 @@
 #include <net/request_sock.h>
 #include <linux/kthread.h>
 #include <linux/nls.h>
+#include <linux/unicode.h>
 
 #include "smb_common.h"
 #include "ksmbd_work.h"
 
 #define KSMBD_SOCKET_BACKLOG		16
 
-/*
- * WARNING
- *
- * This is nothing but a HACK. Session status should move to channel
- * or to session. As of now we have 1 tcp_conn : 1 ksmbd_session, but
- * we need to change it to 1 tcp_conn : N ksmbd_sessions.
- */
 enum {
 	KSMBD_SESS_NEW = 0,
 	KSMBD_SESS_GOOD,
 	KSMBD_SESS_EXITING,
 	KSMBD_SESS_NEED_RECONNECT,
-	KSMBD_SESS_NEED_NEGOTIATE
+	KSMBD_SESS_NEED_NEGOTIATE,
+	KSMBD_SESS_RELEASING
 };
 
 struct ksmbd_stats {
@@ -53,18 +48,21 @@
 	char				*request_buf;
 	struct ksmbd_transport		*transport;
 	struct nls_table		*local_nls;
+	struct unicode_map		*um;
 	struct list_head		conns_list;
+	struct rw_semaphore		session_lock;
 	/* smb session 1 per user */
-	struct list_head		sessions;
+	struct xarray			sessions;
 	unsigned long			last_active;
 	/* How many request are running currently */
 	atomic_t			req_running;
 	/* References which are made for this Server object*/
 	atomic_t			r_count;
-	unsigned short			total_credits;
-	unsigned short			max_credits;
+	unsigned int			total_credits;
+	unsigned int			outstanding_credits;
 	spinlock_t			credits_lock;
 	wait_queue_head_t		req_running_q;
+	wait_queue_head_t		r_count_q;
 	/* Lock to protect requests list*/
 	spinlock_t			request_lock;
 	struct list_head		requests;
@@ -72,12 +70,7 @@
 	int				connection_type;
 	struct ksmbd_stats		stats;
 	char				ClientGUID[SMB2_CLIENT_GUID_SIZE];
-	union {
-		/* pending trans request table */
-		struct trans_state	*recent_trans;
-		/* Used by ntlmssp */
-		char			*ntlmssp_cryptkey;
-	};
+	struct ntlmssp_auth		ntlmssp;
 
 	spinlock_t			llist_lock;
 	struct list_head		lock_list;
@@ -95,6 +88,7 @@
 	__u16				dialect;
 
 	char				*mechToken;
+	unsigned int			mechTokenLen;
 
 	struct ksmbd_conn_ops	*conn_ops;
 
@@ -122,21 +116,25 @@
 struct ksmbd_transport_ops {
 	int (*prepare)(struct ksmbd_transport *t);
 	void (*disconnect)(struct ksmbd_transport *t);
-	int (*read)(struct ksmbd_transport *t, char *buf, unsigned int size);
+	void (*shutdown)(struct ksmbd_transport *t);
+	int (*read)(struct ksmbd_transport *t, char *buf,
+		    unsigned int size, int max_retries);
 	int (*writev)(struct ksmbd_transport *t, struct kvec *iovs, int niov,
 		      int size, bool need_invalidate_rkey,
 		      unsigned int remote_key);
-	int (*rdma_read)(struct ksmbd_transport *t, void *buf, unsigned int len,
-			 u32 remote_key, u64 remote_offset, u32 remote_len);
-	int (*rdma_write)(struct ksmbd_transport *t, void *buf,
-			  unsigned int len, u32 remote_key, u64 remote_offset,
-			  u32 remote_len);
+	int (*rdma_read)(struct ksmbd_transport *t,
+			 void *buf, unsigned int len,
+			 struct smb2_buffer_desc_v1 *desc,
+			 unsigned int desc_len);
+	int (*rdma_write)(struct ksmbd_transport *t,
+			  void *buf, unsigned int len,
+			  struct smb2_buffer_desc_v1 *desc,
+			  unsigned int desc_len);
 };
 
 struct ksmbd_transport {
 	struct ksmbd_conn		*conn;
 	struct ksmbd_transport_ops	*ops;
-	struct task_struct		*handler;
 };
 
 #define KSMBD_TCP_RECV_TIMEOUT	(7 * HZ)
@@ -144,26 +142,30 @@
 #define KSMBD_TCP_PEER_SOCKADDR(c)	((struct sockaddr *)&((c)->peer_addr))
 
 extern struct list_head conn_list;
-extern rwlock_t conn_list_lock;
+extern struct rw_semaphore conn_list_lock;
 
 bool ksmbd_conn_alive(struct ksmbd_conn *conn);
-void ksmbd_conn_wait_idle(struct ksmbd_conn *conn);
+void ksmbd_conn_wait_idle(struct ksmbd_conn *conn, u64 sess_id);
 struct ksmbd_conn *ksmbd_conn_alloc(void);
 void ksmbd_conn_free(struct ksmbd_conn *conn);
 bool ksmbd_conn_lookup_dialect(struct ksmbd_conn *c);
 int ksmbd_conn_write(struct ksmbd_work *work);
-int ksmbd_conn_rdma_read(struct ksmbd_conn *conn, void *buf,
-			 unsigned int buflen, u32 remote_key, u64 remote_offset,
-			 u32 remote_len);
-int ksmbd_conn_rdma_write(struct ksmbd_conn *conn, void *buf,
-			  unsigned int buflen, u32 remote_key, u64 remote_offset,
-			  u32 remote_len);
+int ksmbd_conn_rdma_read(struct ksmbd_conn *conn,
+			 void *buf, unsigned int buflen,
+			 struct smb2_buffer_desc_v1 *desc,
+			 unsigned int desc_len);
+int ksmbd_conn_rdma_write(struct ksmbd_conn *conn,
+			  void *buf, unsigned int buflen,
+			  struct smb2_buffer_desc_v1 *desc,
+			  unsigned int desc_len);
 void ksmbd_conn_enqueue_request(struct ksmbd_work *work);
-int ksmbd_conn_try_dequeue_request(struct ksmbd_work *work);
+void ksmbd_conn_try_dequeue_request(struct ksmbd_work *work);
 void ksmbd_conn_init_server_callbacks(struct ksmbd_conn_ops *ops);
 int ksmbd_conn_handler_loop(void *p);
 int ksmbd_conn_transport_init(void);
 void ksmbd_conn_transport_destroy(void);
+void ksmbd_conn_lock(struct ksmbd_conn *conn);
+void ksmbd_conn_unlock(struct ksmbd_conn *conn);
 
 /*
  * WARNING
@@ -171,43 +173,60 @@
  * This is a hack. We will move status to a proper place once we land
  * a multi-sessions support.
  */
-static inline bool ksmbd_conn_good(struct ksmbd_work *work)
+static inline bool ksmbd_conn_good(struct ksmbd_conn *conn)
+{
+	return READ_ONCE(conn->status) == KSMBD_SESS_GOOD;
+}
+
+static inline bool ksmbd_conn_need_negotiate(struct ksmbd_conn *conn)
 {
-	return work->conn->status == KSMBD_SESS_GOOD;
+	return READ_ONCE(conn->status) == KSMBD_SESS_NEED_NEGOTIATE;
 }
 
-static inline bool ksmbd_conn_need_negotiate(struct ksmbd_work *work)
+static inline bool ksmbd_conn_need_reconnect(struct ksmbd_conn *conn)
 {
-	return work->conn->status == KSMBD_SESS_NEED_NEGOTIATE;
+	return READ_ONCE(conn->status) == KSMBD_SESS_NEED_RECONNECT;
 }
 
-static inline bool ksmbd_conn_need_reconnect(struct ksmbd_work *work)
+static inline bool ksmbd_conn_exiting(struct ksmbd_conn *conn)
 {
-	return work->conn->status == KSMBD_SESS_NEED_RECONNECT;
+	return READ_ONCE(conn->status) == KSMBD_SESS_EXITING;
 }
 
-static inline bool ksmbd_conn_exiting(struct ksmbd_work *work)
+static inline bool ksmbd_conn_releasing(struct ksmbd_conn *conn)
 {
-	return work->conn->status == KSMBD_SESS_EXITING;
+	return READ_ONCE(conn->status) == KSMBD_SESS_RELEASING;
 }
 
-static inline void ksmbd_conn_set_good(struct ksmbd_work *work)
+static inline void ksmbd_conn_set_new(struct ksmbd_conn *conn)
 {
-	work->conn->status = KSMBD_SESS_GOOD;
+	WRITE_ONCE(conn->status, KSMBD_SESS_NEW);
 }
 
-static inline void ksmbd_conn_set_need_negotiate(struct ksmbd_work *work)
+static inline void ksmbd_conn_set_good(struct ksmbd_conn *conn)
 {
-	work->conn->status = KSMBD_SESS_NEED_NEGOTIATE;
+	WRITE_ONCE(conn->status, KSMBD_SESS_GOOD);
 }
 
-static inline void ksmbd_conn_set_need_reconnect(struct ksmbd_work *work)
+static inline void ksmbd_conn_set_need_negotiate(struct ksmbd_conn *conn)
 {
-	work->conn->status = KSMBD_SESS_NEED_RECONNECT;
+	WRITE_ONCE(conn->status, KSMBD_SESS_NEED_NEGOTIATE);
 }
 
-static inline void ksmbd_conn_set_exiting(struct ksmbd_work *work)
+static inline void ksmbd_conn_set_need_reconnect(struct ksmbd_conn *conn)
 {
-	work->conn->status = KSMBD_SESS_EXITING;
+	WRITE_ONCE(conn->status, KSMBD_SESS_NEED_RECONNECT);
 }
+
+static inline void ksmbd_conn_set_exiting(struct ksmbd_conn *conn)
+{
+	WRITE_ONCE(conn->status, KSMBD_SESS_EXITING);
+}
+
+static inline void ksmbd_conn_set_releasing(struct ksmbd_conn *conn)
+{
+	WRITE_ONCE(conn->status, KSMBD_SESS_RELEASING);
+}
+
+void ksmbd_all_conn_set_status(u64 sess_id, u32 status);
 #endif /* __CONNECTION_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/ksmbd_netlink.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/ksmbd_netlink.h
@@ -74,6 +74,7 @@
 #define KSMBD_GLOBAL_FLAG_SMB2_LEASES		BIT(0)
 #define KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION	BIT(1)
 #define KSMBD_GLOBAL_FLAG_SMB3_MULTICHANNEL	BIT(2)
+#define KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION_OFF	BIT(3)
 
 /*
  * IPC request for ksmbd server startup
@@ -103,6 +104,10 @@
 					 * we set the SPARSE_FILES bit (0x40).
 					 */
 	__u32	sub_auth[3];		/* Subauth value for Security ID */
+	__u32	smb2_max_credits;	/* MAX credits */
+	__u32	smbd_max_io_size;	/* smbd read write size */
+	__u32	max_connections;	/* Number of maximum simultaneous connections */
+	__u32	reserved[126];		/* Reserved room */
 	__u32	ifc_list_sz;		/* interfaces list size */
 	__s8	____payload[];
 };
@@ -113,7 +118,7 @@
  * IPC request to shutdown ksmbd server.
  */
 struct ksmbd_shutdown_request {
-	__s32	reserved;
+	__s32	reserved[16];
 };
 
 /*
@@ -122,6 +127,7 @@
 struct ksmbd_login_request {
 	__u32	handle;
 	__s8	account[KSMBD_REQ_MAX_ACCOUNT_NAME_SZ]; /* user account name */
+	__u32	reserved[16];				/* Reserved room */
 };
 
 /*
@@ -135,6 +141,7 @@
 	__u16	status;
 	__u16	hash_sz;			/* hash size */
 	__s8	hash[KSMBD_REQ_MAX_HASH_SZ];	/* password hash */
+	__u32	reserved[16];			/* Reserved room */
 };
 
 /*
@@ -143,6 +150,7 @@
 struct ksmbd_share_config_request {
 	__u32	handle;
 	__s8	share_name[KSMBD_REQ_MAX_SHARE_NAME]; /* share name */
+	__u32	reserved[16];		/* Reserved room */
 };
 
 /*
@@ -157,6 +165,9 @@
 	__u16	force_directory_mode;
 	__u16	force_uid;
 	__u16	force_gid;
+	__s8	share_name[KSMBD_REQ_MAX_SHARE_NAME];
+	__u32	reserved[111];		/* Reserved room */
+	__u32	payload_sz;
 	__u32	veto_list_sz;
 	__s8	____payload[];
 };
@@ -187,6 +198,7 @@
 	__s8	account[KSMBD_REQ_MAX_ACCOUNT_NAME_SZ];
 	__s8	share[KSMBD_REQ_MAX_SHARE_NAME];
 	__s8	peer_addr[64];
+	__u32	reserved[16];		/* Reserved room */
 };
 
 /*
@@ -196,6 +208,7 @@
 	__u32	handle;
 	__u16	status;
 	__u16	connection_flags;
+	__u32	reserved[16];		/* Reserved room */
 };
 
 /*
@@ -204,6 +217,7 @@
 struct ksmbd_tree_disconnect_request {
 	__u64	session_id;	/* session id */
 	__u64	connect_id;	/* tree connection id */
+	__u32	reserved[16];	/* Reserved room */
 };
 
 /*
@@ -212,6 +226,7 @@
 struct ksmbd_logout_request {
 	__s8	account[KSMBD_REQ_MAX_ACCOUNT_NAME_SZ]; /* user account name */
 	__u32	account_flags;
+	__u32	reserved[16];				/* Reserved room */
 };
 
 /*
@@ -290,7 +305,8 @@
 	KSMBD_EVENT_SPNEGO_AUTHEN_REQUEST,
 	KSMBD_EVENT_SPNEGO_AUTHEN_RESPONSE	= 15,
 
-	KSMBD_EVENT_MAX
+	__KSMBD_EVENT_MAX,
+	KSMBD_EVENT_MAX = __KSMBD_EVENT_MAX - 1
 };
 
 /*
@@ -338,6 +354,8 @@
 #define KSMBD_SHARE_FLAG_STREAMS		BIT(11)
 #define KSMBD_SHARE_FLAG_FOLLOW_SYMLINKS	BIT(12)
 #define KSMBD_SHARE_FLAG_ACL_XATTR		BIT(13)
+#define KSMBD_SHARE_FLAG_UPDATE			BIT(14)
+#define KSMBD_SHARE_FLAG_CROSSMNT		BIT(15)
 
 /*
  * Tree connect request flags.
@@ -353,6 +371,7 @@
 #define KSMBD_TREE_CONN_FLAG_READ_ONLY		BIT(1)
 #define KSMBD_TREE_CONN_FLAG_WRITABLE		BIT(2)
 #define KSMBD_TREE_CONN_FLAG_ADMIN_ACCOUNT	BIT(3)
+#define KSMBD_TREE_CONN_FLAG_UPDATE		BIT(4)
 
 /*
  * RPC over IPC.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/ksmbd_work.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/ksmbd_work.c
@@ -27,18 +27,38 @@
 		INIT_LIST_HEAD(&work->async_request_entry);
 		INIT_LIST_HEAD(&work->fp_entry);
 		INIT_LIST_HEAD(&work->interim_entry);
+		INIT_LIST_HEAD(&work->aux_read_list);
+		work->iov_alloc_cnt = 4;
+		work->iov = kcalloc(work->iov_alloc_cnt, sizeof(struct kvec),
+				    GFP_KERNEL);
+		if (!work->iov) {
+			kmem_cache_free(work_cache, work);
+			work = NULL;
+		}
 	}
 	return work;
 }
 
 void ksmbd_free_work_struct(struct ksmbd_work *work)
 {
+	struct aux_read *ar, *tmp;
+
 	WARN_ON(work->saved_cred != NULL);
 
 	kvfree(work->response_buf);
-	kvfree(work->aux_payload_buf);
+
+	list_for_each_entry_safe(ar, tmp, &work->aux_read_list, entry) {
+		kvfree(ar->buf);
+		list_del(&ar->entry);
+		kfree(ar);
+	}
+
 	kfree(work->tr_buf);
 	kvfree(work->request_buf);
+	kfree(work->iov);
+	if (!list_empty(&work->interim_entry))
+		list_del(&work->interim_entry);
+
 	if (work->async_id)
 		ksmbd_release_id(&work->conn->async_ida, work->async_id);
 	kmem_cache_free(work_cache, work);
@@ -69,7 +89,6 @@
 
 void ksmbd_workqueue_destroy(void)
 {
-	flush_workqueue(ksmbd_wq);
 	destroy_workqueue(ksmbd_wq);
 	ksmbd_wq = NULL;
 }
@@ -78,3 +97,81 @@
 {
 	return queue_work(ksmbd_wq, &work->work);
 }
+
+static inline void __ksmbd_iov_pin(struct ksmbd_work *work, void *ib,
+				   unsigned int ib_len)
+{
+	work->iov[++work->iov_idx].iov_base = ib;
+	work->iov[work->iov_idx].iov_len = ib_len;
+	work->iov_cnt++;
+}
+
+static int __ksmbd_iov_pin_rsp(struct ksmbd_work *work, void *ib, int len,
+			       void *aux_buf, unsigned int aux_size)
+{
+	struct aux_read *ar = NULL;
+	int need_iov_cnt = 1;
+
+	if (aux_size) {
+		need_iov_cnt++;
+		ar = kmalloc(sizeof(struct aux_read), GFP_KERNEL);
+		if (!ar)
+			return -ENOMEM;
+	}
+
+	if (work->iov_alloc_cnt < work->iov_cnt + need_iov_cnt) {
+		struct kvec *new;
+
+		work->iov_alloc_cnt += 4;
+		new = krealloc(work->iov,
+			       sizeof(struct kvec) * work->iov_alloc_cnt,
+			       GFP_KERNEL | __GFP_ZERO);
+		if (!new) {
+			kfree(ar);
+			work->iov_alloc_cnt -= 4;
+			return -ENOMEM;
+		}
+		work->iov = new;
+	}
+
+	/* Plus rfc_length size on first iov */
+	if (!work->iov_idx) {
+		work->iov[work->iov_idx].iov_base = work->response_buf;
+		*(__be32 *)work->iov[0].iov_base = 0;
+		work->iov[work->iov_idx].iov_len = 4;
+		work->iov_cnt++;
+	}
+
+	__ksmbd_iov_pin(work, ib, len);
+	inc_rfc1001_len(work->iov[0].iov_base, len);
+
+	if (aux_size) {
+		__ksmbd_iov_pin(work, aux_buf, aux_size);
+		inc_rfc1001_len(work->iov[0].iov_base, aux_size);
+
+		ar->buf = aux_buf;
+		list_add(&ar->entry, &work->aux_read_list);
+	}
+
+	return 0;
+}
+
+int ksmbd_iov_pin_rsp(struct ksmbd_work *work, void *ib, int len)
+{
+	return __ksmbd_iov_pin_rsp(work, ib, len, NULL, 0);
+}
+
+int ksmbd_iov_pin_rsp_read(struct ksmbd_work *work, void *ib, int len,
+			   void *aux_buf, unsigned int aux_size)
+{
+	return __ksmbd_iov_pin_rsp(work, ib, len, aux_buf, aux_size);
+}
+
+int allocate_interim_rsp_buf(struct ksmbd_work *work)
+{
+	work->response_buf = kzalloc(MAX_CIFS_SMALL_BUFFER_SIZE, GFP_KERNEL);
+	if (!work->response_buf)
+		return -ENOMEM;
+	work->response_sz = MAX_CIFS_SMALL_BUFFER_SIZE;
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/ksmbd_work.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/ksmbd_work.h
@@ -19,6 +19,11 @@
 	KSMBD_WORK_CLOSED,
 };
 
+struct aux_read {
+	void *buf;
+	struct list_head entry;
+};
+
 /* one of these for every pending CIFS request at the connection */
 struct ksmbd_work {
 	/* Server corresponding to this mid */
@@ -31,13 +36,19 @@
 	/* Response buffer */
 	void                            *response_buf;
 
-	/* Read data buffer */
-	void                            *aux_payload_buf;
+	struct list_head		aux_read_list;
+
+	struct kvec			*iov;
+	int				iov_alloc_cnt;
+	int				iov_cnt;
+	int				iov_idx;
 
 	/* Next cmd hdr in compound req buf*/
 	int                             next_smb2_rcv_hdr_off;
 	/* Next cmd hdr in compound rsp buf*/
 	int                             next_smb2_rsp_hdr_off;
+	/* Current cmd hdr in compound rsp buf*/
+	int                             curr_smb2_rsp_hdr_off;
 
 	/*
 	 * Current Local FID assigned compound response if SMB2 CREATE
@@ -53,22 +64,17 @@
 	unsigned int			credits_granted;
 
 	/* response smb header size */
-	unsigned int                    resp_hdr_sz;
 	unsigned int                    response_sz;
-	/* Read data count */
-	unsigned int                    aux_payload_sz;
 
 	void				*tr_buf;
 
 	unsigned char			state;
-	/* Multiple responses for one request e.g. SMB ECHO */
-	bool                            multiRsp:1;
 	/* No response for cancelled request */
 	bool                            send_no_response:1;
 	/* Request is encrypted */
 	bool                            encrypted:1;
 	/* Is this SYNC or ASYNC ksmbd_work */
-	bool                            syncronous:1;
+	bool                            asynchronous:1;
 	bool                            need_invalidate_rkey:1;
 
 	unsigned int                    remote_key;
@@ -92,7 +98,16 @@
  */
 static inline void *ksmbd_resp_buf_next(struct ksmbd_work *work)
 {
-	return work->response_buf + work->next_smb2_rsp_hdr_off;
+	return work->response_buf + work->next_smb2_rsp_hdr_off + 4;
+}
+
+/**
+ * ksmbd_resp_buf_curr - Get current buffer on compound response.
+ * @work: smb work containing response buffer
+ */
+static inline void *ksmbd_resp_buf_curr(struct ksmbd_work *work)
+{
+	return work->response_buf + work->curr_smb2_rsp_hdr_off + 4;
 }
 
 /**
@@ -101,7 +116,7 @@
  */
 static inline void *ksmbd_req_buf_next(struct ksmbd_work *work)
 {
-	return work->request_buf + work->next_smb2_rcv_hdr_off;
+	return work->request_buf + work->next_smb2_rcv_hdr_off + 4;
 }
 
 struct ksmbd_work *ksmbd_alloc_work_struct(void);
@@ -113,5 +128,8 @@
 int ksmbd_workqueue_init(void);
 void ksmbd_workqueue_destroy(void);
 bool ksmbd_queue_work(struct ksmbd_work *work);
-
+int ksmbd_iov_pin_rsp_read(struct ksmbd_work *work, void *ib, int len,
+			   void *aux_buf, unsigned int aux_size);
+int ksmbd_iov_pin_rsp(struct ksmbd_work *work, void *ib, int len);
+int allocate_interim_rsp_buf(struct ksmbd_work *work);
 #endif /* __KSMBD_WORK_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/share_config.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/share_config.c
@@ -16,6 +16,7 @@
 #include "user_config.h"
 #include "user_session.h"
 #include "../transport_ipc.h"
+#include "../misc.h"
 
 #define SHARE_HASH_BITS		3
 static DEFINE_HASHTABLE(shares_table, SHARE_HASH_BITS);
@@ -26,7 +27,7 @@
 	struct list_head	list;
 };
 
-static unsigned int share_name_hash(char *name)
+static unsigned int share_name_hash(const char *name)
 {
 	return jhash(name, strlen(name), 0);
 }
@@ -51,12 +52,16 @@
 	kfree(share);
 }
 
-void __ksmbd_share_config_put(struct ksmbd_share_config *share)
+void ksmbd_share_config_del(struct ksmbd_share_config *share)
 {
 	down_write(&shares_table_lock);
 	hash_del(&share->hlist);
 	up_write(&shares_table_lock);
+}
 
+void __ksmbd_share_config_put(struct ksmbd_share_config *share)
+{
+	ksmbd_share_config_del(share);
 	kill_share(share);
 }
 
@@ -68,7 +73,7 @@
 	return share;
 }
 
-static struct ksmbd_share_config *__share_lookup(char *name)
+static struct ksmbd_share_config *__share_lookup(const char *name)
 {
 	struct ksmbd_share_config *share;
 	unsigned int key = share_name_hash(name);
@@ -115,7 +120,8 @@
 	return 0;
 }
 
-static struct ksmbd_share_config *share_config_request(char *name)
+static struct ksmbd_share_config *share_config_request(struct unicode_map *um,
+						       const char *name)
 {
 	struct ksmbd_share_config_response *resp;
 	struct ksmbd_share_config *share = NULL;
@@ -129,6 +135,19 @@
 	if (resp->flags == KSMBD_SHARE_FLAG_INVALID)
 		goto out;
 
+	if (*resp->share_name) {
+		char *cf_resp_name;
+		bool equal;
+
+		cf_resp_name = ksmbd_casefold_sharename(um, resp->share_name);
+		if (IS_ERR(cf_resp_name))
+			goto out;
+		equal = !strcmp(cf_resp_name, name);
+		kfree(cf_resp_name);
+		if (!equal)
+			goto out;
+	}
+
 	share = kzalloc(sizeof(struct ksmbd_share_config), GFP_KERNEL);
 	if (!share)
 		goto out;
@@ -139,10 +158,19 @@
 	share->name = kstrdup(name, GFP_KERNEL);
 
 	if (!test_share_config_flag(share, KSMBD_SHARE_FLAG_PIPE)) {
-		share->path = kstrdup(ksmbd_share_config_path(resp),
+		int path_len = PATH_MAX;
+
+		if (resp->payload_sz)
+			path_len = resp->payload_sz - resp->veto_list_sz;
+
+		share->path = kstrndup(ksmbd_share_config_path(resp), path_len,
 				      GFP_KERNEL);
-		if (share->path)
+		if (share->path) {
 			share->path_sz = strlen(share->path);
+			while (share->path_sz > 1 &&
+			       share->path[share->path_sz - 1] == '/')
+				share->path[--share->path_sz] = '\0';
+		}
 		share->create_mask = resp->create_mask;
 		share->directory_mask = resp->directory_mask;
 		share->force_create_mode = resp->force_create_mode;
@@ -186,20 +214,11 @@
 	return share;
 }
 
-static void strtolower(char *share_name)
-{
-	while (*share_name) {
-		*share_name = tolower(*share_name);
-		share_name++;
-	}
-}
-
-struct ksmbd_share_config *ksmbd_share_config_get(char *name)
+struct ksmbd_share_config *ksmbd_share_config_get(struct unicode_map *um,
+						  const char *name)
 {
 	struct ksmbd_share_config *share;
 
-	strtolower(name);
-
 	down_read(&shares_table_lock);
 	share = __share_lookup(name);
 	if (share)
@@ -208,7 +227,7 @@
 
 	if (share)
 		return share;
-	return share_config_request(name);
+	return share_config_request(um, name);
 }
 
 bool ksmbd_share_veto_filename(struct ksmbd_share_config *share,
@@ -222,17 +241,3 @@
 	}
 	return false;
 }
-
-void ksmbd_share_configs_cleanup(void)
-{
-	struct ksmbd_share_config *share;
-	struct hlist_node *tmp;
-	int i;
-
-	down_write(&shares_table_lock);
-	hash_for_each_safe(shares_table, i, tmp, share, hlist) {
-		hash_del(&share->hlist);
-		kill_share(share);
-	}
-	up_write(&shares_table_lock);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/share_config.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/share_config.h
@@ -9,6 +9,7 @@
 #include <linux/workqueue.h>
 #include <linux/hashtable.h>
 #include <linux/path.h>
+#include <linux/unicode.h>
 
 struct ksmbd_share_config {
 	char			*name;
@@ -33,29 +34,22 @@
 #define KSMBD_SHARE_INVALID_UID	((__u16)-1)
 #define KSMBD_SHARE_INVALID_GID	((__u16)-1)
 
-static inline int share_config_create_mode(struct ksmbd_share_config *share,
-					   umode_t posix_mode)
+static inline umode_t
+share_config_create_mode(struct ksmbd_share_config *share,
+			 umode_t posix_mode)
 {
-	if (!share->force_create_mode) {
-		if (!posix_mode)
-			return share->create_mask;
-		else
-			return posix_mode & share->create_mask;
-	}
-	return share->force_create_mode & share->create_mask;
+	umode_t mode = (posix_mode ?: (umode_t)-1) & share->create_mask;
+
+	return mode | share->force_create_mode;
 }
 
-static inline int share_config_directory_mode(struct ksmbd_share_config *share,
-					      umode_t posix_mode)
+static inline umode_t
+share_config_directory_mode(struct ksmbd_share_config *share,
+			    umode_t posix_mode)
 {
-	if (!share->force_directory_mode) {
-		if (!posix_mode)
-			return share->directory_mask;
-		else
-			return posix_mode & share->directory_mask;
-	}
+	umode_t mode = (posix_mode ?: (umode_t)-1) & share->directory_mask;
 
-	return share->force_directory_mode & share->directory_mask;
+	return mode | share->force_directory_mode;
 }
 
 static inline int test_share_config_flag(struct ksmbd_share_config *share,
@@ -64,6 +58,7 @@
 	return share->flags & flag;
 }
 
+void ksmbd_share_config_del(struct ksmbd_share_config *share);
 void __ksmbd_share_config_put(struct ksmbd_share_config *share);
 
 static inline void ksmbd_share_config_put(struct ksmbd_share_config *share)
@@ -73,9 +68,8 @@
 	__ksmbd_share_config_put(share);
 }
 
-struct ksmbd_share_config *ksmbd_share_config_get(char *name);
+struct ksmbd_share_config *ksmbd_share_config_get(struct unicode_map *um,
+						  const char *name);
 bool ksmbd_share_veto_filename(struct ksmbd_share_config *share,
 			       const char *filename);
-void ksmbd_share_configs_cleanup(void);
-
 #endif /* __SHARE_CONFIG_MANAGEMENT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/tree_connect.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/tree_connect.c
@@ -16,16 +16,17 @@
 #include "user_session.h"
 
 struct ksmbd_tree_conn_status
-ksmbd_tree_conn_connect(struct ksmbd_session *sess, char *share_name)
+ksmbd_tree_conn_connect(struct ksmbd_conn *conn, struct ksmbd_session *sess,
+			const char *share_name)
 {
-	struct ksmbd_tree_conn_status status = {-EINVAL, NULL};
+	struct ksmbd_tree_conn_status status = {-ENOENT, NULL};
 	struct ksmbd_tree_connect_response *resp = NULL;
 	struct ksmbd_share_config *sc;
 	struct ksmbd_tree_connect *tree_conn = NULL;
 	struct sockaddr *peer_addr;
 	int ret;
 
-	sc = ksmbd_share_config_get(share_name);
+	sc = ksmbd_share_config_get(conn->um, share_name);
 	if (!sc)
 		return status;
 
@@ -41,7 +42,7 @@
 		goto out_error;
 	}
 
-	peer_addr = KSMBD_TCP_PEER_SOCKADDR(sess->conn);
+	peer_addr = KSMBD_TCP_PEER_SOCKADDR(conn);
 	resp = ksmbd_ipc_tree_connect_request(sess,
 					      sc,
 					      tree_conn,
@@ -56,9 +57,26 @@
 		goto out_error;
 
 	tree_conn->flags = resp->connection_flags;
+	if (test_tree_conn_flag(tree_conn, KSMBD_TREE_CONN_FLAG_UPDATE)) {
+		struct ksmbd_share_config *new_sc;
+
+		ksmbd_share_config_del(sc);
+		new_sc = ksmbd_share_config_get(conn->um, share_name);
+		if (!new_sc) {
+			pr_err("Failed to update stale share config\n");
+			status.ret = -ESTALE;
+			goto out_error;
+		}
+		ksmbd_share_config_put(sc);
+		sc = new_sc;
+	}
+
 	tree_conn->user = sess->user;
 	tree_conn->share_conf = sc;
+	tree_conn->t_state = TREE_NEW;
 	status.tree_conn = tree_conn;
+	atomic_set(&tree_conn->refcount, 1);
+	init_waitqueue_head(&tree_conn->refcount_q);
 
 	ret = xa_err(xa_store(&sess->tree_conns, tree_conn->id, tree_conn,
 			      GFP_KERNEL));
@@ -78,14 +96,33 @@
 	return status;
 }
 
+void ksmbd_tree_connect_put(struct ksmbd_tree_connect *tcon)
+{
+	/*
+	 * Checking waitqueue to releasing tree connect on
+	 * tree disconnect. waitqueue_active is safe because it
+	 * uses atomic operation for condition.
+	 */
+	if (!atomic_dec_return(&tcon->refcount) &&
+	    waitqueue_active(&tcon->refcount_q))
+		wake_up(&tcon->refcount_q);
+}
+
 int ksmbd_tree_conn_disconnect(struct ksmbd_session *sess,
 			       struct ksmbd_tree_connect *tree_conn)
 {
 	int ret;
 
+	write_lock(&sess->tree_conns_lock);
+	xa_erase(&sess->tree_conns, tree_conn->id);
+	write_unlock(&sess->tree_conns_lock);
+
+	if (!atomic_dec_and_test(&tree_conn->refcount))
+		wait_event(tree_conn->refcount_q,
+			   atomic_read(&tree_conn->refcount) == 0);
+
 	ret = ksmbd_ipc_tree_disconnect_request(sess->id, tree_conn->id);
 	ksmbd_release_tree_conn_id(sess, tree_conn->id);
-	xa_erase(&sess->tree_conns, tree_conn->id);
 	ksmbd_share_config_put(tree_conn->share_conf);
 	kfree(tree_conn);
 	return ret;
@@ -94,18 +131,19 @@
 struct ksmbd_tree_connect *ksmbd_tree_conn_lookup(struct ksmbd_session *sess,
 						  unsigned int id)
 {
-	return xa_load(&sess->tree_conns, id);
-}
+	struct ksmbd_tree_connect *tcon;
 
-struct ksmbd_share_config *ksmbd_tree_conn_share(struct ksmbd_session *sess,
-						 unsigned int id)
-{
-	struct ksmbd_tree_connect *tc;
+	read_lock(&sess->tree_conns_lock);
+	tcon = xa_load(&sess->tree_conns, id);
+	if (tcon) {
+		if (tcon->t_state != TREE_CONNECTED)
+			tcon = NULL;
+		else if (!atomic_inc_not_zero(&tcon->refcount))
+			tcon = NULL;
+	}
+	read_unlock(&sess->tree_conns_lock);
 
-	tc = ksmbd_tree_conn_lookup(sess, id);
-	if (tc)
-		return tc->share_conf;
-	return NULL;
+	return tcon;
 }
 
 int ksmbd_tree_conn_session_logoff(struct ksmbd_session *sess)
@@ -114,8 +152,21 @@
 	struct ksmbd_tree_connect *tc;
 	unsigned long id;
 
-	xa_for_each(&sess->tree_conns, id, tc)
+	if (!sess)
+		return -EINVAL;
+
+	xa_for_each(&sess->tree_conns, id, tc) {
+		write_lock(&sess->tree_conns_lock);
+		if (tc->t_state == TREE_DISCONNECTED) {
+			write_unlock(&sess->tree_conns_lock);
+			ret = -ENOENT;
+			continue;
+		}
+		tc->t_state = TREE_DISCONNECTED;
+		write_unlock(&sess->tree_conns_lock);
+
 		ret |= ksmbd_tree_conn_disconnect(sess, tc);
+	}
 	xa_destroy(&sess->tree_conns);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/tree_connect.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/tree_connect.h
@@ -12,6 +12,13 @@
 
 struct ksmbd_share_config;
 struct ksmbd_user;
+struct ksmbd_conn;
+
+enum {
+	TREE_NEW = 0,
+	TREE_CONNECTED,
+	TREE_DISCONNECTED
+};
 
 struct ksmbd_tree_connect {
 	int				id;
@@ -24,6 +31,9 @@
 
 	int				maximal_access;
 	bool				posix_extensions;
+	atomic_t			refcount;
+	wait_queue_head_t		refcount_q;
+	unsigned int			t_state;
 };
 
 struct ksmbd_tree_conn_status {
@@ -40,7 +50,9 @@
 struct ksmbd_session;
 
 struct ksmbd_tree_conn_status
-ksmbd_tree_conn_connect(struct ksmbd_session *sess, char *share_name);
+ksmbd_tree_conn_connect(struct ksmbd_conn *conn, struct ksmbd_session *sess,
+			const char *share_name);
+void ksmbd_tree_connect_put(struct ksmbd_tree_connect *tcon);
 
 int ksmbd_tree_conn_disconnect(struct ksmbd_session *sess,
 			       struct ksmbd_tree_connect *tree_conn);
@@ -48,9 +60,6 @@
 struct ksmbd_tree_connect *ksmbd_tree_conn_lookup(struct ksmbd_session *sess,
 						  unsigned int id);
 
-struct ksmbd_share_config *ksmbd_tree_conn_share(struct ksmbd_session *sess,
-						 unsigned int id);
-
 int ksmbd_tree_conn_session_logoff(struct ksmbd_session *sess);
 
 #endif /* __TREE_CONNECT_MANAGEMENT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/user_config.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/user_config.c
@@ -67,3 +67,13 @@
 		return 1;
 	return 0;
 }
+
+bool ksmbd_compare_user(struct ksmbd_user *u1, struct ksmbd_user *u2)
+{
+	if (strcmp(u1->name, u2->name))
+		return false;
+	if (memcmp(u1->passkey, u2->passkey, u1->passkey_sz))
+		return false;
+
+	return true;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/user_config.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/user_config.h
@@ -18,7 +18,6 @@
 
 	size_t			passkey_sz;
 	char			*passkey;
-	unsigned int		failed_login_count;
 };
 
 static inline bool user_guest(struct ksmbd_user *user)
@@ -64,4 +63,5 @@
 struct ksmbd_user *ksmbd_alloc_user(struct ksmbd_login_response *resp);
 void ksmbd_free_user(struct ksmbd_user *user);
 int ksmbd_anonymous_user(struct ksmbd_user *user);
+bool ksmbd_compare_user(struct ksmbd_user *u1, struct ksmbd_user *u2);
 #endif /* __USER_CONFIG_MANAGEMENT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/user_session.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/user_session.c
@@ -25,18 +25,19 @@
 struct ksmbd_session_rpc {
 	int			id;
 	unsigned int		method;
-	struct list_head	list;
 };
 
 static void free_channel_list(struct ksmbd_session *sess)
 {
-	struct channel *chann, *tmp;
+	struct channel *chann;
+	unsigned long index;
 
-	list_for_each_entry_safe(chann, tmp, &sess->ksmbd_chann_list,
-				 chann_list) {
-		list_del(&chann->chann_list);
+	xa_for_each(&sess->ksmbd_chann_list, index, chann) {
+		xa_erase(&sess->ksmbd_chann_list, index);
 		kfree(chann);
 	}
+
+	xa_destroy(&sess->ksmbd_chann_list);
 }
 
 static void __session_rpc_close(struct ksmbd_session *sess,
@@ -56,15 +57,14 @@
 static void ksmbd_session_rpc_clear_list(struct ksmbd_session *sess)
 {
 	struct ksmbd_session_rpc *entry;
+	long index;
 
-	while (!list_empty(&sess->rpc_handle_list)) {
-		entry = list_entry(sess->rpc_handle_list.next,
-				   struct ksmbd_session_rpc,
-				   list);
-
-		list_del(&entry->list);
+	xa_for_each(&sess->rpc_handle_list, index, entry) {
+		xa_erase(&sess->rpc_handle_list, index);
 		__session_rpc_close(sess, entry);
 	}
+
+	xa_destroy(&sess->rpc_handle_list);
 }
 
 static int __rpc_method(char *rpc_name)
@@ -100,22 +100,24 @@
 
 	entry = kzalloc(sizeof(struct ksmbd_session_rpc), GFP_KERNEL);
 	if (!entry)
-		return -EINVAL;
+		return -ENOMEM;
 
-	list_add(&entry->list, &sess->rpc_handle_list);
 	entry->method = method;
 	entry->id = ksmbd_ipc_id_alloc();
 	if (entry->id < 0)
-		goto error;
+		goto free_entry;
+	xa_store(&sess->rpc_handle_list, entry->id, entry, GFP_KERNEL);
 
 	resp = ksmbd_rpc_open(sess, entry->id);
 	if (!resp)
-		goto error;
+		goto free_id;
 
 	kvfree(resp);
 	return entry->id;
-error:
-	list_del(&entry->list);
+free_id:
+	xa_erase(&sess->rpc_handle_list, entry->id);
+	ksmbd_rpc_id_free(entry->id);
+free_entry:
 	kfree(entry);
 	return -EINVAL;
 }
@@ -124,24 +126,17 @@
 {
 	struct ksmbd_session_rpc *entry;
 
-	list_for_each_entry(entry, &sess->rpc_handle_list, list) {
-		if (entry->id == id) {
-			list_del(&entry->list);
-			__session_rpc_close(sess, entry);
-			break;
-		}
-	}
+	entry = xa_erase(&sess->rpc_handle_list, id);
+	if (entry)
+		__session_rpc_close(sess, entry);
 }
 
 int ksmbd_session_rpc_method(struct ksmbd_session *sess, int id)
 {
 	struct ksmbd_session_rpc *entry;
 
-	list_for_each_entry(entry, &sess->rpc_handle_list, list) {
-		if (entry->id == id)
-			return entry->method;
-	}
-	return 0;
+	entry = xa_load(&sess->rpc_handle_list, id);
+	return entry ? entry->method : 0;
 }
 
 void ksmbd_session_destroy(struct ksmbd_session *sess)
@@ -149,15 +144,6 @@
 	if (!sess)
 		return;
 
-	if (!atomic_dec_and_test(&sess->refcnt))
-		return;
-
-	list_del(&sess->sessions_entry);
-
-	down_write(&sessions_table_lock);
-	hash_del(&sess->hlist);
-	up_write(&sessions_table_lock);
-
 	if (sess->user)
 		ksmbd_free_user(sess->user);
 
@@ -175,59 +161,124 @@
 	struct ksmbd_session *sess;
 
 	hash_for_each_possible(sessions_table, sess, hlist, id) {
-		if (id == sess->id)
+		if (id == sess->id) {
+			sess->last_active = jiffies;
 			return sess;
+		}
 	}
 	return NULL;
 }
 
-void ksmbd_session_register(struct ksmbd_conn *conn,
-			    struct ksmbd_session *sess)
+static void ksmbd_expire_session(struct ksmbd_conn *conn)
+{
+	unsigned long id;
+	struct ksmbd_session *sess;
+
+	down_write(&conn->session_lock);
+	xa_for_each(&conn->sessions, id, sess) {
+		if (atomic_read(&sess->refcnt) == 0 &&
+		    (sess->state != SMB2_SESSION_VALID ||
+		     time_after(jiffies,
+			       sess->last_active + SMB2_SESSION_TIMEOUT))) {
+			xa_erase(&conn->sessions, sess->id);
+			hash_del(&sess->hlist);
+			ksmbd_session_destroy(sess);
+			continue;
+		}
+	}
+	up_write(&conn->session_lock);
+}
+
+int ksmbd_session_register(struct ksmbd_conn *conn,
+			   struct ksmbd_session *sess)
 {
-	sess->conn = conn;
-	list_add(&sess->sessions_entry, &conn->sessions);
+	sess->dialect = conn->dialect;
+	memcpy(sess->ClientGUID, conn->ClientGUID, SMB2_CLIENT_GUID_SIZE);
+	ksmbd_expire_session(conn);
+	return xa_err(xa_store(&conn->sessions, sess->id, sess, GFP_KERNEL));
+}
+
+static int ksmbd_chann_del(struct ksmbd_conn *conn, struct ksmbd_session *sess)
+{
+	struct channel *chann;
+
+	chann = xa_erase(&sess->ksmbd_chann_list, (long)conn);
+	if (!chann)
+		return -ENOENT;
+
+	kfree(chann);
+	return 0;
 }
 
 void ksmbd_sessions_deregister(struct ksmbd_conn *conn)
 {
 	struct ksmbd_session *sess;
+	unsigned long id;
+
+	down_write(&sessions_table_lock);
+	if (conn->binding) {
+		int bkt;
+		struct hlist_node *tmp;
+
+		hash_for_each_safe(sessions_table, bkt, tmp, sess, hlist) {
+			if (!ksmbd_chann_del(conn, sess) &&
+			    xa_empty(&sess->ksmbd_chann_list)) {
+				hash_del(&sess->hlist);
+				ksmbd_session_destroy(sess);
+			}
+		}
+	}
+	up_write(&sessions_table_lock);
 
-	while (!list_empty(&conn->sessions)) {
-		sess = list_entry(conn->sessions.next,
-				  struct ksmbd_session,
-				  sessions_entry);
+	down_write(&conn->session_lock);
+	xa_for_each(&conn->sessions, id, sess) {
+		unsigned long chann_id;
+		struct channel *chann;
+
+		xa_for_each(&sess->ksmbd_chann_list, chann_id, chann) {
+			if (chann->conn != conn)
+				ksmbd_conn_set_exiting(chann->conn);
+		}
 
-		ksmbd_session_destroy(sess);
+		ksmbd_chann_del(conn, sess);
+		if (xa_empty(&sess->ksmbd_chann_list)) {
+			xa_erase(&conn->sessions, sess->id);
+			hash_del(&sess->hlist);
+			ksmbd_session_destroy(sess);
+		}
 	}
+	up_write(&conn->session_lock);
 }
 
-static bool ksmbd_session_id_match(struct ksmbd_session *sess,
+bool is_ksmbd_session_in_connection(struct ksmbd_conn *conn,
 				   unsigned long long id)
 {
-	return sess->id == id;
+	struct ksmbd_session *sess;
+
+	down_read(&conn->session_lock);
+	sess = xa_load(&conn->sessions, id);
+	if (sess) {
+		up_read(&conn->session_lock);
+		return true;
+	}
+	up_read(&conn->session_lock);
+
+	return false;
 }
 
 struct ksmbd_session *ksmbd_session_lookup(struct ksmbd_conn *conn,
 					   unsigned long long id)
 {
-	struct ksmbd_session *sess = NULL;
+	struct ksmbd_session *sess;
 
-	list_for_each_entry(sess, &conn->sessions, sessions_entry) {
-		if (ksmbd_session_id_match(sess, id))
-			return sess;
+	down_read(&conn->session_lock);
+	sess = xa_load(&conn->sessions, id);
+	if (sess) {
+		sess->last_active = jiffies;
+		ksmbd_user_session_get(sess);
 	}
-	return NULL;
-}
-
-int get_session(struct ksmbd_session *sess)
-{
-	return atomic_inc_not_zero(&sess->refcnt);
-}
-
-void put_session(struct ksmbd_session *sess)
-{
-	if (atomic_dec_and_test(&sess->refcnt))
-		pr_err("get/%s seems to be mismatched.", __func__);
+	up_read(&conn->session_lock);
+	return sess;
 }
 
 struct ksmbd_session *ksmbd_session_lookup_slowpath(unsigned long long id)
@@ -236,10 +287,8 @@
 
 	down_read(&sessions_table_lock);
 	sess = __session_lookup(id);
-	if (sess) {
-		if (!get_session(sess))
-			sess = NULL;
-	}
+	if (sess)
+		ksmbd_user_session_get(sess);
 	up_read(&sessions_table_lock);
 
 	return sess;
@@ -253,9 +302,27 @@
 	sess = ksmbd_session_lookup(conn, id);
 	if (!sess && conn->binding)
 		sess = ksmbd_session_lookup_slowpath(id);
+	if (sess && sess->state != SMB2_SESSION_VALID)
+		sess = NULL;
 	return sess;
 }
 
+void ksmbd_user_session_get(struct ksmbd_session *sess)
+{
+	atomic_inc(&sess->refcnt);
+}
+
+void ksmbd_user_session_put(struct ksmbd_session *sess)
+{
+	if (!sess)
+		return;
+
+	if (atomic_read(&sess->refcnt) <= 0)
+		WARN_ON(1);
+	else
+		atomic_dec(&sess->refcnt);
+}
+
 struct preauth_session *ksmbd_preauth_session_alloc(struct ksmbd_conn *conn,
 						    u64 sess_id)
 {
@@ -306,6 +373,9 @@
 	struct ksmbd_session *sess;
 	int ret;
 
+	if (protocol != CIFDS_SESSION_FLAG_SMB2)
+		return NULL;
+
 	sess = kzalloc(sizeof(struct ksmbd_session), GFP_KERNEL);
 	if (!sess)
 		return NULL;
@@ -313,33 +383,26 @@
 	if (ksmbd_init_file_table(&sess->file_table))
 		goto error;
 
+	sess->last_active = jiffies;
+	sess->state = SMB2_SESSION_IN_PROGRESS;
 	set_session_flag(sess, protocol);
-	INIT_LIST_HEAD(&sess->sessions_entry);
 	xa_init(&sess->tree_conns);
-	INIT_LIST_HEAD(&sess->ksmbd_chann_list);
-	INIT_LIST_HEAD(&sess->rpc_handle_list);
+	xa_init(&sess->ksmbd_chann_list);
+	xa_init(&sess->rpc_handle_list);
 	sess->sequence_number = 1;
+	rwlock_init(&sess->tree_conns_lock);
 	atomic_set(&sess->refcnt, 1);
 
-	switch (protocol) {
-	case CIFDS_SESSION_FLAG_SMB2:
-		ret = __init_smb2_session(sess);
-		break;
-	default:
-		ret = -EINVAL;
-		break;
-	}
-
+	ret = __init_smb2_session(sess);
 	if (ret)
 		goto error;
 
 	ida_init(&sess->tree_conn_ida);
 
-	if (protocol == CIFDS_SESSION_FLAG_SMB2) {
-		down_write(&sessions_table_lock);
-		hash_add(sessions_table, &sess->hlist, sess->id);
-		up_write(&sessions_table_lock);
-	}
+	down_write(&sessions_table_lock);
+	hash_add(sessions_table, &sess->hlist, sess->id);
+	up_write(&sessions_table_lock);
+
 	return sess;
 
 error:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/mgmt/user_session.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/mgmt/user_session.h
@@ -21,7 +21,6 @@
 struct channel {
 	__u8			smb3signingkey[SMB3_SIGN_KEY_SIZE];
 	struct ksmbd_conn	*conn;
-	struct list_head	chann_list;
 };
 
 struct preauth_session {
@@ -33,8 +32,10 @@
 struct ksmbd_session {
 	u64				id;
 
+	__u16				dialect;
+	char				ClientGUID[SMB2_CLIENT_GUID_SIZE];
+
 	struct ksmbd_user		*user;
-	struct ksmbd_conn		*conn;
 	unsigned int			sequence_number;
 	unsigned int			flags;
 
@@ -45,21 +46,22 @@
 	int				state;
 	__u8				*Preauth_HashValue;
 
-	struct ntlmssp_auth		ntlmssp;
 	char				sess_key[CIFS_KEY_SIZE];
 
 	struct hlist_node		hlist;
-	struct list_head		ksmbd_chann_list;
+	struct xarray			ksmbd_chann_list;
 	struct xarray			tree_conns;
 	struct ida			tree_conn_ida;
-	struct list_head		rpc_handle_list;
+	struct xarray			rpc_handle_list;
 
 	__u8				smb3encryptionkey[SMB3_ENC_DEC_KEY_SIZE];
 	__u8				smb3decryptionkey[SMB3_ENC_DEC_KEY_SIZE];
 	__u8				smb3signingkey[SMB3_SIGN_KEY_SIZE];
 
-	struct list_head		sessions_entry;
 	struct ksmbd_file_table		file_table;
+	unsigned long			last_active;
+	rwlock_t			tree_conns_lock;
+
 	atomic_t			refcnt;
 };
 
@@ -85,8 +87,10 @@
 struct ksmbd_session *ksmbd_session_lookup_slowpath(unsigned long long id);
 struct ksmbd_session *ksmbd_session_lookup(struct ksmbd_conn *conn,
 					   unsigned long long id);
-void ksmbd_session_register(struct ksmbd_conn *conn,
-			    struct ksmbd_session *sess);
+bool is_ksmbd_session_in_connection(struct ksmbd_conn *conn,
+				     unsigned long long id);
+int ksmbd_session_register(struct ksmbd_conn *conn,
+			   struct ksmbd_session *sess);
 void ksmbd_sessions_deregister(struct ksmbd_conn *conn);
 struct ksmbd_session *ksmbd_session_lookup_all(struct ksmbd_conn *conn,
 					       unsigned long long id);
@@ -101,6 +105,6 @@
 int ksmbd_session_rpc_open(struct ksmbd_session *sess, char *rpc_name);
 void ksmbd_session_rpc_close(struct ksmbd_session *sess, int id);
 int ksmbd_session_rpc_method(struct ksmbd_session *sess, int id);
-int get_session(struct ksmbd_session *sess);
-void put_session(struct ksmbd_session *sess);
+void ksmbd_user_session_get(struct ksmbd_session *sess);
+void ksmbd_user_session_put(struct ksmbd_session *sess);
 #endif /* __USER_SESSION_MANAGEMENT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/misc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/misc.c
@@ -7,6 +7,7 @@
 #include <linux/kernel.h>
 #include <linux/xattr.h>
 #include <linux/fs.h>
+#include <linux/unicode.h>
 
 #include "misc.h"
 #include "smb_common.h"
@@ -20,7 +21,7 @@
  * wildcard '*' and '?'
  * TODO : implement consideration about DOS_DOT, DOS_QM and DOS_STAR
  *
- * @string:	string to compare with a pattern
+ * @str:	string to compare with a pattern
  * @len:	string length
  * @pattern:	pattern string which might include wildcard '*' and '?'
  *
@@ -152,25 +153,47 @@
 /**
  * convert_to_nt_pathname() - extract and return windows path string
  *      whose share directory prefix was removed from file path
- * @filename : unix filename
- * @sharepath: share path string
+ * @share: ksmbd_share_config pointer
+ * @path: path to report
  *
  * Return : windows path string or error
  */
 
-char *convert_to_nt_pathname(char *filename)
+char *convert_to_nt_pathname(struct ksmbd_share_config *share,
+			     const struct path *path)
 {
-	char *ab_pathname;
+	char *pathname, *ab_pathname, *nt_pathname;
+	int share_path_len = share->path_sz;
 
-	if (strlen(filename) == 0)
-		filename = "\\";
+	pathname = kmalloc(PATH_MAX, GFP_KERNEL);
+	if (!pathname)
+		return ERR_PTR(-EACCES);
+
+	ab_pathname = d_path(path, pathname, PATH_MAX);
+	if (IS_ERR(ab_pathname)) {
+		nt_pathname = ERR_PTR(-EACCES);
+		goto free_pathname;
+	}
 
-	ab_pathname = kstrdup(filename, GFP_KERNEL);
-	if (!ab_pathname)
-		return NULL;
+	if (strncmp(ab_pathname, share->path, share_path_len)) {
+		nt_pathname = ERR_PTR(-EACCES);
+		goto free_pathname;
+	}
 
-	ksmbd_conv_path_to_windows(ab_pathname);
-	return ab_pathname;
+	nt_pathname = kzalloc(strlen(&ab_pathname[share_path_len]) + 2, GFP_KERNEL);
+	if (!nt_pathname) {
+		nt_pathname = ERR_PTR(-ENOMEM);
+		goto free_pathname;
+	}
+	if (ab_pathname[share_path_len] == '\0')
+		strcpy(nt_pathname, "/");
+	strcat(nt_pathname, &ab_pathname[share_path_len]);
+
+	ksmbd_conv_path_to_windows(nt_pathname);
+
+free_pathname:
+	kfree(pathname);
+	return nt_pathname;
 }
 
 int get_nlink(struct kstat *st)
@@ -204,32 +227,59 @@
 	strreplace(path, '/', '\\');
 }
 
+char *ksmbd_casefold_sharename(struct unicode_map *um, const char *name)
+{
+	char *cf_name;
+	int cf_len;
+
+	cf_name = kzalloc(KSMBD_REQ_MAX_SHARE_NAME, GFP_KERNEL);
+	if (!cf_name)
+		return ERR_PTR(-ENOMEM);
+
+	if (IS_ENABLED(CONFIG_UNICODE) && um) {
+		const struct qstr q_name = {.name = name, .len = strlen(name)};
+
+		cf_len = utf8_casefold(um, &q_name, cf_name,
+				       KSMBD_REQ_MAX_SHARE_NAME);
+		if (cf_len < 0)
+			goto out_ascii;
+
+		return cf_name;
+	}
+
+out_ascii:
+	cf_len = strscpy(cf_name, name, KSMBD_REQ_MAX_SHARE_NAME);
+	if (cf_len < 0) {
+		kfree(cf_name);
+		return ERR_PTR(-E2BIG);
+	}
+
+	for (; *cf_name; ++cf_name)
+		*cf_name = isascii(*cf_name) ? tolower(*cf_name) : *cf_name;
+	return cf_name - cf_len;
+}
+
 /**
  * ksmbd_extract_sharename() - get share name from tree connect request
  * @treename:	buffer containing tree name and share name
  *
  * Return:      share name on success, otherwise error
  */
-char *ksmbd_extract_sharename(char *treename)
+char *ksmbd_extract_sharename(struct unicode_map *um, const char *treename)
 {
-	char *name = treename;
-	char *dst;
-	char *pos = strrchr(name, '\\');
+	const char *name = treename, *pos = strrchr(name, '\\');
 
 	if (pos)
 		name = (pos + 1);
 
 	/* caller has to free the memory */
-	dst = kstrdup(name, GFP_KERNEL);
-	if (!dst)
-		return ERR_PTR(-ENOMEM);
-	return dst;
+	return ksmbd_casefold_sharename(um, name);
 }
 
 /**
  * convert_to_unix_name() - convert windows name to unix format
- * @path:	name to be converted
- * @tid:	tree id of mathing share
+ * @share:	ksmbd_share_config pointer
+ * @name:	file name that is relative to share
  *
  * Return:	converted name on success, otherwise NULL
  */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/misc.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/misc.h
@@ -14,12 +14,14 @@
 int match_pattern(const char *str, size_t len, const char *pattern);
 int ksmbd_validate_filename(char *filename);
 int parse_stream_name(char *filename, char **stream_name, int *s_type);
-char *convert_to_nt_pathname(char *filename);
+char *convert_to_nt_pathname(struct ksmbd_share_config *share,
+			     const struct path *path);
 int get_nlink(struct kstat *st);
 void ksmbd_conv_path_to_unix(char *path);
 void ksmbd_strip_last_slash(char *path);
 void ksmbd_conv_path_to_windows(char *path);
-char *ksmbd_extract_sharename(char *treename);
+char *ksmbd_casefold_sharename(struct unicode_map *um, const char *name);
+char *ksmbd_extract_sharename(struct unicode_map *um, const char *treename);
 char *convert_to_unix_name(struct ksmbd_share_config *share, const char *name);
 
 #define KSMBD_DIR_INFO_ALIGNMENT	8
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/ndr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/ndr.c
@@ -148,7 +148,7 @@
 static int ndr_read_int32(struct ndr *n, __u32 *value)
 {
 	if (n->offset + sizeof(__u32) > n->length)
-		return 0;
+		return -EINVAL;
 
 	if (value)
 		*value = le32_to_cpu(*(__le32 *)ndr_get_field(n));
@@ -242,7 +242,7 @@
 		return ret;
 
 	if (da->version != 3 && da->version != 4) {
-		pr_err("v%d version is not supported\n", da->version);
+		ksmbd_debug(VFS, "v%d version is not supported\n", da->version);
 		return -EINVAL;
 	}
 
@@ -251,7 +251,7 @@
 		return ret;
 
 	if (da->version != version2) {
-		pr_err("ndr version mismatched(version: %d, version2: %d)\n",
+		ksmbd_debug(VFS, "ndr version mismatched(version: %d, version2: %d)\n",
 		       da->version, version2);
 		return -EINVAL;
 	}
@@ -453,7 +453,7 @@
 	if (ret)
 		return ret;
 	if (acl->version != 4) {
-		pr_err("v%d version is not supported\n", acl->version);
+		ksmbd_debug(VFS, "v%d version is not supported\n", acl->version);
 		return -EINVAL;
 	}
 
@@ -461,7 +461,7 @@
 	if (ret)
 		return ret;
 	if (acl->version != version2) {
-		pr_err("ndr version mismatched(version: %d, version2: %d)\n",
+		ksmbd_debug(VFS, "ndr version mismatched(version: %d, version2: %d)\n",
 		       acl->version, version2);
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/oplock.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/oplock.c
@@ -30,6 +30,7 @@
 static struct oplock_info *alloc_opinfo(struct ksmbd_work *work,
 					u64 id, __u16 Tid)
 {
+	struct ksmbd_conn *conn = work->conn;
 	struct ksmbd_session *sess = work->sess;
 	struct oplock_info *opinfo;
 
@@ -38,7 +39,7 @@
 		return NULL;
 
 	opinfo->sess = sess;
-	opinfo->conn = sess->conn;
+	opinfo->conn = conn;
 	opinfo->level = SMB2_OPLOCK_LEVEL_NONE;
 	opinfo->op_state = OPLOCK_STATE_NONE;
 	opinfo->pending_break = 0;
@@ -101,9 +102,10 @@
 	lease->new_state = 0;
 	lease->flags = lctx->flags;
 	lease->duration = lctx->duration;
+	lease->is_dir = lctx->is_dir;
 	memcpy(lease->parent_lease_key, lctx->parent_lease_key, SMB2_LEASE_KEY_SIZE);
 	lease->version = lctx->version;
-	lease->epoch = 0;
+	lease->epoch = le16_to_cpu(lctx->epoch) + 1;
 	INIT_LIST_HEAD(&opinfo->lease_entry);
 	opinfo->o_lease = lease;
 
@@ -156,13 +158,42 @@
 	rcu_read_lock();
 	opinfo = list_first_or_null_rcu(&ci->m_op_list, struct oplock_info,
 					op_entry);
-	if (opinfo && !atomic_inc_not_zero(&opinfo->refcount))
-		opinfo = NULL;
+	if (opinfo) {
+		if (!atomic_inc_not_zero(&opinfo->refcount))
+			opinfo = NULL;
+		else {
+			atomic_inc(&opinfo->conn->r_count);
+			if (ksmbd_conn_releasing(opinfo->conn)) {
+				atomic_dec(&opinfo->conn->r_count);
+				atomic_dec(&opinfo->refcount);
+				opinfo = NULL;
+			}
+		}
+	}
+
 	rcu_read_unlock();
 
 	return opinfo;
 }
 
+static void opinfo_conn_put(struct oplock_info *opinfo)
+{
+	struct ksmbd_conn *conn;
+
+	if (!opinfo)
+		return;
+
+	conn = opinfo->conn;
+	/*
+	 * Checking waitqueue to dropping pending requests on
+	 * disconnection. waitqueue_active is safe because it
+	 * uses atomic operation for condition.
+	 */
+	if (!atomic_dec_return(&conn->r_count) && waitqueue_active(&conn->r_count_q))
+		wake_up(&conn->r_count_q);
+	opinfo_put(opinfo);
+}
+
 void opinfo_put(struct oplock_info *opinfo)
 {
 	if (!atomic_dec_and_test(&opinfo->refcount))
@@ -365,8 +396,8 @@
 {
 	struct oplock_info *opinfo;
 
-	if (S_ISDIR(file_inode(fp->filp)->i_mode))
-		return;
+	if (fp->reserve_lease_break)
+		smb_lazy_parent_lease_break_close(fp);
 
 	opinfo = opinfo_get(fp);
 	if (!opinfo)
@@ -513,24 +544,30 @@
 			/* upgrading lease */
 			if ((atomic_read(&ci->op_count) +
 			     atomic_read(&ci->sop_count)) == 1) {
-				if (lease->state ==
-				    (lctx->req_state & lease->state)) {
+				if (lease->state != SMB2_LEASE_NONE_LE &&
+				    lease->state == (lctx->req_state & lease->state)) {
+					lease->epoch++;
 					lease->state |= lctx->req_state;
 					if (lctx->req_state &
 						SMB2_LEASE_WRITE_CACHING_LE)
 						lease_read_to_write(opinfo);
+
 				}
 			} else if ((atomic_read(&ci->op_count) +
 				    atomic_read(&ci->sop_count)) > 1) {
 				if (lctx->req_state ==
 				    (SMB2_LEASE_READ_CACHING_LE |
-				     SMB2_LEASE_HANDLE_CACHING_LE))
+				     SMB2_LEASE_HANDLE_CACHING_LE)) {
+					lease->epoch++;
 					lease->state = lctx->req_state;
+				}
 			}
 
 			if (lctx->req_state && lease->state ==
-			    SMB2_LEASE_NONE_LE)
+			    SMB2_LEASE_NONE_LE) {
+				lease->epoch++;
 				lease_none_upgrade(opinfo, lctx->req_state);
+			}
 		}
 		read_lock(&ci->m_lock);
 	}
@@ -586,15 +623,6 @@
 	return 0;
 }
 
-static inline int allocate_oplock_break_buf(struct ksmbd_work *work)
-{
-	work->response_buf = kzalloc(MAX_CIFS_SMALL_BUFFER_SIZE, GFP_KERNEL);
-	if (!work->response_buf)
-		return -ENOMEM;
-	work->response_sz = MAX_CIFS_SMALL_BUFFER_SIZE;
-	return 0;
-}
-
 /**
  * __smb2_oplock_break_noti() - send smb2 oplock break cmd from conn
  * to client
@@ -609,30 +637,22 @@
 {
 	struct smb2_oplock_break *rsp = NULL;
 	struct ksmbd_work *work = container_of(wk, struct ksmbd_work, work);
-	struct ksmbd_conn *conn = work->conn;
 	struct oplock_break_info *br_info = work->request_buf;
 	struct smb2_hdr *rsp_hdr;
 	struct ksmbd_file *fp;
 
 	fp = ksmbd_lookup_durable_fd(br_info->fid);
-	if (!fp) {
-		atomic_dec(&conn->r_count);
-		ksmbd_free_work_struct(work);
-		return;
-	}
+	if (!fp)
+		goto out;
 
-	if (allocate_oplock_break_buf(work)) {
+	if (allocate_interim_rsp_buf(work)) {
 		pr_err("smb2_allocate_rsp_buf failed! ");
-		atomic_dec(&conn->r_count);
 		ksmbd_fd_put(work, fp);
-		ksmbd_free_work_struct(work);
-		return;
+		goto out;
 	}
 
-	rsp_hdr = work->response_buf;
+	rsp_hdr = smb2_get_msg(work->response_buf);
 	memset(rsp_hdr, 0, sizeof(struct smb2_hdr) + 2);
-	rsp_hdr->smb2_buf_length =
-		cpu_to_be32(smb2_hdr_size_no_buflen(conn->vals));
 	rsp_hdr->ProtocolId = SMB2_PROTO_NUMBER;
 	rsp_hdr->StructureSize = SMB2_HEADER_STRUCTURE_SIZE;
 	rsp_hdr->CreditRequest = cpu_to_le16(0);
@@ -645,7 +665,7 @@
 	rsp_hdr->SessionId = 0;
 	memset(rsp_hdr->Signature, 0, 16);
 
-	rsp = work->response_buf;
+	rsp = smb2_get_msg(work->response_buf);
 
 	rsp->StructureSize = cpu_to_le16(24);
 	if (!br_info->open_trunc &&
@@ -656,19 +676,22 @@
 		rsp->OplockLevel = SMB2_OPLOCK_LEVEL_NONE;
 	rsp->Reserved = 0;
 	rsp->Reserved2 = 0;
-	rsp->PersistentFid = cpu_to_le64(fp->persistent_id);
-	rsp->VolatileFid = cpu_to_le64(fp->volatile_id);
+	rsp->PersistentFid = fp->persistent_id;
+	rsp->VolatileFid = fp->volatile_id;
 
-	inc_rfc1001_len(rsp, 24);
+	ksmbd_fd_put(work, fp);
+	if (ksmbd_iov_pin_rsp(work, (void *)rsp,
+			      sizeof(struct smb2_oplock_break)))
+		goto out;
 
 	ksmbd_debug(OPLOCK,
 		    "sending oplock break v_id %llu p_id = %llu lock level = %d\n",
 		    rsp->VolatileFid, rsp->PersistentFid, rsp->OplockLevel);
 
-	ksmbd_fd_put(work, fp);
 	ksmbd_conn_write(work);
+
+out:
 	ksmbd_free_work_struct(work);
-	atomic_dec(&conn->r_count);
 }
 
 /**
@@ -702,7 +725,6 @@
 	work->conn = conn;
 	work->sess = opinfo->sess;
 
-	atomic_inc(&conn->r_count);
 	if (opinfo->op_state == OPLOCK_ACK_WAIT) {
 		INIT_WORK(&work->work, __smb2_oplock_break_noti);
 		ksmbd_queue_work(work);
@@ -726,20 +748,15 @@
 	struct smb2_lease_break *rsp = NULL;
 	struct ksmbd_work *work = container_of(wk, struct ksmbd_work, work);
 	struct lease_break_info *br_info = work->request_buf;
-	struct ksmbd_conn *conn = work->conn;
 	struct smb2_hdr *rsp_hdr;
 
-	if (allocate_oplock_break_buf(work)) {
+	if (allocate_interim_rsp_buf(work)) {
 		ksmbd_debug(OPLOCK, "smb2_allocate_rsp_buf failed! ");
-		ksmbd_free_work_struct(work);
-		atomic_dec(&conn->r_count);
-		return;
+		goto out;
 	}
 
-	rsp_hdr = work->response_buf;
+	rsp_hdr = smb2_get_msg(work->response_buf);
 	memset(rsp_hdr, 0, sizeof(struct smb2_hdr) + 2);
-	rsp_hdr->smb2_buf_length =
-		cpu_to_be32(smb2_hdr_size_no_buflen(conn->vals));
 	rsp_hdr->ProtocolId = SMB2_PROTO_NUMBER;
 	rsp_hdr->StructureSize = SMB2_HEADER_STRUCTURE_SIZE;
 	rsp_hdr->CreditRequest = cpu_to_le16(0);
@@ -752,7 +769,7 @@
 	rsp_hdr->SessionId = 0;
 	memset(rsp_hdr->Signature, 0, 16);
 
-	rsp = work->response_buf;
+	rsp = smb2_get_msg(work->response_buf);
 	rsp->StructureSize = cpu_to_le16(44);
 	rsp->Epoch = br_info->epoch;
 	rsp->Flags = 0;
@@ -768,11 +785,14 @@
 	rsp->AccessMaskHint = 0;
 	rsp->ShareMaskHint = 0;
 
-	inc_rfc1001_len(rsp, 44);
+	if (ksmbd_iov_pin_rsp(work, (void *)rsp,
+			      sizeof(struct smb2_lease_break)))
+		goto out;
 
 	ksmbd_conn_write(work);
+
+out:
 	ksmbd_free_work_struct(work);
-	atomic_dec(&conn->r_count);
 }
 
 /**
@@ -812,7 +832,6 @@
 	work->conn = conn;
 	work->sess = opinfo->sess;
 
-	atomic_inc(&conn->r_count);
 	if (opinfo->op_state == OPLOCK_ACK_WAIT) {
 		list_for_each_safe(tmp, t, &opinfo->interim_list) {
 			struct ksmbd_work *in_work;
@@ -821,7 +840,8 @@
 					     interim_entry);
 			setup_async_work(in_work, NULL, NULL);
 			smb2_send_interim_resp(in_work, STATUS_PENDING);
-			list_del(&in_work->interim_entry);
+			list_del_init(&in_work->interim_entry);
+			release_async_work(in_work);
 		}
 		INIT_WORK(&work->work, __smb2_lease_break_noti);
 		ksmbd_queue_work(work);
@@ -887,7 +907,8 @@
 					lease->new_state =
 						SMB2_LEASE_READ_CACHING_LE;
 			} else {
-				if (lease->state & SMB2_LEASE_HANDLE_CACHING_LE)
+				if (lease->state & SMB2_LEASE_HANDLE_CACHING_LE &&
+						!lease->is_dir)
 					lease->new_state =
 						SMB2_LEASE_READ_CACHING_LE;
 				else
@@ -972,7 +993,7 @@
 	}
 
 	list_for_each_entry(lb, &lease_table_list, l_entry) {
-		if (!memcmp(lb->client_guid, sess->conn->ClientGUID,
+		if (!memcmp(lb->client_guid, sess->ClientGUID,
 			    SMB2_CLIENT_GUID_SIZE))
 			goto found;
 	}
@@ -988,7 +1009,7 @@
 		rcu_read_unlock();
 		if (opinfo->o_fp->f_ci == ci)
 			goto op_next;
-		err = compare_guid_key(opinfo, sess->conn->ClientGUID,
+		err = compare_guid_key(opinfo, sess->ClientGUID,
 				       lctx->lease_key);
 		if (err) {
 			err = -EINVAL;
@@ -1019,6 +1040,8 @@
 	       SMB2_LEASE_KEY_SIZE);
 	lease2->duration = lease1->duration;
 	lease2->flags = lease1->flags;
+	lease2->epoch = lease1->epoch;
+	lease2->version = lease1->version;
 }
 
 static int add_lease_global_list(struct oplock_info *opinfo)
@@ -1068,6 +1091,89 @@
 	}
 }
 
+void smb_send_parent_lease_break_noti(struct ksmbd_file *fp,
+				      struct lease_ctx_info *lctx)
+{
+	struct oplock_info *opinfo;
+	struct ksmbd_inode *p_ci = NULL;
+
+	if (lctx->version != 2)
+		return;
+
+	p_ci = ksmbd_inode_lookup_lock(fp->filp->f_path.dentry->d_parent);
+	if (!p_ci)
+		return;
+
+	read_lock(&p_ci->m_lock);
+	list_for_each_entry(opinfo, &p_ci->m_op_list, op_entry) {
+		if (!opinfo->is_lease)
+			continue;
+
+		if (opinfo->o_lease->state != SMB2_OPLOCK_LEVEL_NONE &&
+		    (!(lctx->flags & SMB2_LEASE_FLAG_PARENT_LEASE_KEY_SET_LE) ||
+		     !compare_guid_key(opinfo, fp->conn->ClientGUID,
+				      lctx->parent_lease_key))) {
+			if (!atomic_inc_not_zero(&opinfo->refcount))
+				continue;
+
+			atomic_inc(&opinfo->conn->r_count);
+			if (ksmbd_conn_releasing(opinfo->conn)) {
+				atomic_dec(&opinfo->conn->r_count);
+				continue;
+			}
+
+			read_unlock(&p_ci->m_lock);
+			oplock_break(opinfo, SMB2_OPLOCK_LEVEL_NONE);
+			opinfo_conn_put(opinfo);
+			read_lock(&p_ci->m_lock);
+		}
+	}
+	read_unlock(&p_ci->m_lock);
+
+	ksmbd_inode_put(p_ci);
+}
+
+void smb_lazy_parent_lease_break_close(struct ksmbd_file *fp)
+{
+	struct oplock_info *opinfo;
+	struct ksmbd_inode *p_ci = NULL;
+
+	rcu_read_lock();
+	opinfo = rcu_dereference(fp->f_opinfo);
+	rcu_read_unlock();
+
+	if (!opinfo->is_lease || opinfo->o_lease->version != 2)
+		return;
+
+	p_ci = ksmbd_inode_lookup_lock(fp->filp->f_path.dentry->d_parent);
+	if (!p_ci)
+		return;
+
+	read_lock(&p_ci->m_lock);
+	list_for_each_entry(opinfo, &p_ci->m_op_list, op_entry) {
+		if (!opinfo->is_lease)
+			continue;
+
+		if (opinfo->o_lease->state != SMB2_OPLOCK_LEVEL_NONE) {
+			if (!atomic_inc_not_zero(&opinfo->refcount))
+				continue;
+
+			atomic_inc(&opinfo->conn->r_count);
+			if (ksmbd_conn_releasing(opinfo->conn)) {
+				atomic_dec(&opinfo->conn->r_count);
+				continue;
+			}
+			read_unlock(&p_ci->m_lock);
+			oplock_break(opinfo, SMB2_OPLOCK_LEVEL_NONE);
+			opinfo_conn_put(opinfo);
+			read_lock(&p_ci->m_lock);
+		}
+	}
+	read_unlock(&p_ci->m_lock);
+
+	ksmbd_inode_put(p_ci);
+}
+
 /**
  * smb_grant_oplock() - handle oplock/lease request on file open
  * @work:		smb work
@@ -1091,9 +1197,11 @@
 	bool prev_op_has_lease;
 	__le32 prev_op_state = 0;
 
-	/* not support directory lease */
-	if (S_ISDIR(file_inode(fp->filp)->i_mode))
-		return 0;
+	/* Only v2 leases handle the directory */
+	if (S_ISDIR(file_inode(fp->filp)->i_mode)) {
+		if (!lctx || lctx->version != 2)
+			return 0;
+	}
 
 	opinfo = alloc_opinfo(work, pid, tid);
 	if (!opinfo)
@@ -1122,7 +1230,7 @@
 		struct oplock_info *m_opinfo;
 
 		/* is lease already granted ? */
-		m_opinfo = same_client_has_lease(ci, sess->conn->ClientGUID,
+		m_opinfo = same_client_has_lease(ci, sess->ClientGUID,
 						 lctx);
 		if (m_opinfo) {
 			copy_lease(m_opinfo, opinfo);
@@ -1134,8 +1242,10 @@
 	}
 	prev_opinfo = opinfo_get_list(ci);
 	if (!prev_opinfo ||
-	    (prev_opinfo->level == SMB2_OPLOCK_LEVEL_NONE && lctx))
+	    (prev_opinfo->level == SMB2_OPLOCK_LEVEL_NONE && lctx)) {
+		opinfo_conn_put(prev_opinfo);
 		goto set_lev;
+	}
 	prev_op_has_lease = prev_opinfo->is_lease;
 	if (prev_op_has_lease)
 		prev_op_state = prev_opinfo->o_lease->state;
@@ -1143,19 +1253,19 @@
 	if (share_ret < 0 &&
 	    prev_opinfo->level == SMB2_OPLOCK_LEVEL_EXCLUSIVE) {
 		err = share_ret;
-		opinfo_put(prev_opinfo);
+		opinfo_conn_put(prev_opinfo);
 		goto err_out;
 	}
 
 	if (prev_opinfo->level != SMB2_OPLOCK_LEVEL_BATCH &&
 	    prev_opinfo->level != SMB2_OPLOCK_LEVEL_EXCLUSIVE) {
-		opinfo_put(prev_opinfo);
+		opinfo_conn_put(prev_opinfo);
 		goto op_break_not_needed;
 	}
 
 	list_add(&work->interim_entry, &prev_opinfo->interim_list);
 	err = oplock_break(prev_opinfo, SMB2_OPLOCK_LEVEL_II);
-	opinfo_put(prev_opinfo);
+	opinfo_conn_put(prev_opinfo);
 	if (err == -ENOENT)
 		goto set_lev;
 	/* Check all oplock was freed by close */
@@ -1218,14 +1328,14 @@
 		return;
 	if (brk_opinfo->level != SMB2_OPLOCK_LEVEL_BATCH &&
 	    brk_opinfo->level != SMB2_OPLOCK_LEVEL_EXCLUSIVE) {
-		opinfo_put(brk_opinfo);
+		opinfo_conn_put(brk_opinfo);
 		return;
 	}
 
 	brk_opinfo->open_trunc = is_trunc;
 	list_add(&work->interim_entry, &brk_opinfo->interim_list);
 	oplock_break(brk_opinfo, SMB2_OPLOCK_LEVEL_II);
-	opinfo_put(brk_opinfo);
+	opinfo_conn_put(brk_opinfo);
 }
 
 /**
@@ -1240,7 +1350,7 @@
 {
 	struct oplock_info *op, *brk_op;
 	struct ksmbd_inode *ci;
-	struct ksmbd_conn *conn = work->sess->conn;
+	struct ksmbd_conn *conn = work->conn;
 
 	if (!test_share_config_flag(work->tcon->share_conf,
 				    KSMBD_SHARE_FLAG_OPLOCKS))
@@ -1253,6 +1363,13 @@
 	list_for_each_entry_rcu(brk_op, &ci->m_op_list, op_entry) {
 		if (!atomic_inc_not_zero(&brk_op->refcount))
 			continue;
+
+		atomic_inc(&brk_op->conn->r_count);
+		if (ksmbd_conn_releasing(brk_op->conn)) {
+			atomic_dec(&brk_op->conn->r_count);
+			continue;
+		}
+
 		rcu_read_unlock();
 		if (brk_op->is_lease && (brk_op->o_lease->state &
 		    (~(SMB2_LEASE_READ_CACHING_LE |
@@ -1282,7 +1399,7 @@
 		brk_op->open_trunc = is_trunc;
 		oplock_break(brk_op, SMB2_OPLOCK_LEVEL_NONE);
 next:
-		opinfo_put(brk_op);
+		opinfo_conn_put(brk_op);
 		rcu_read_lock();
 	}
 	rcu_read_unlock();
@@ -1335,19 +1452,17 @@
  */
 void create_lease_buf(u8 *rbuf, struct lease *lease)
 {
-	char *LeaseKey = (char *)&lease->lease_key;
-
 	if (lease->version == 2) {
 		struct create_lease_v2 *buf = (struct create_lease_v2 *)rbuf;
-		char *ParentLeaseKey = (char *)&lease->parent_lease_key;
 
 		memset(buf, 0, sizeof(struct create_lease_v2));
-		buf->lcontext.LeaseKeyLow = *((__le64 *)LeaseKey);
-		buf->lcontext.LeaseKeyHigh = *((__le64 *)(LeaseKey + 8));
+		memcpy(buf->lcontext.LeaseKey, lease->lease_key,
+		       SMB2_LEASE_KEY_SIZE);
 		buf->lcontext.LeaseFlags = lease->flags;
+		buf->lcontext.Epoch = cpu_to_le16(lease->epoch);
 		buf->lcontext.LeaseState = lease->state;
-		buf->lcontext.ParentLeaseKeyLow = *((__le64 *)ParentLeaseKey);
-		buf->lcontext.ParentLeaseKeyHigh = *((__le64 *)(ParentLeaseKey + 8));
+		memcpy(buf->lcontext.ParentLeaseKey, lease->parent_lease_key,
+		       SMB2_LEASE_KEY_SIZE);
 		buf->ccontext.DataOffset = cpu_to_le16(offsetof
 				(struct create_lease_v2, lcontext));
 		buf->ccontext.DataLength = cpu_to_le32(sizeof(struct lease_context_v2));
@@ -1362,8 +1477,7 @@
 		struct create_lease *buf = (struct create_lease *)rbuf;
 
 		memset(buf, 0, sizeof(struct create_lease));
-		buf->lcontext.LeaseKeyLow = *((__le64 *)LeaseKey);
-		buf->lcontext.LeaseKeyHigh = *((__le64 *)(LeaseKey + 8));
+		memcpy(buf->lcontext.LeaseKey, lease->lease_key, SMB2_LEASE_KEY_SIZE);
 		buf->lcontext.LeaseFlags = lease->flags;
 		buf->lcontext.LeaseState = lease->state;
 		buf->ccontext.DataOffset = cpu_to_le16(offsetof
@@ -1382,74 +1496,62 @@
 /**
  * parse_lease_state() - parse lease context containted in file open request
  * @open_req:	buffer containing smb2 file open(create) request
+ * @is_dir:	whether leasing file is directory
  *
  * Return:  oplock state, -ENOENT if create lease context not found
  */
-struct lease_ctx_info *parse_lease_state(void *open_req)
+struct lease_ctx_info *parse_lease_state(void *open_req, bool is_dir)
 {
-	char *data_offset;
 	struct create_context *cc;
-	unsigned int next = 0;
-	char *name;
-	bool found = false;
 	struct smb2_create_req *req = (struct smb2_create_req *)open_req;
-	struct lease_ctx_info *lreq = kzalloc(sizeof(struct lease_ctx_info),
-		GFP_KERNEL);
-	if (!lreq)
+	struct lease_ctx_info *lreq;
+
+	cc = smb2_find_context_vals(req, SMB2_CREATE_REQUEST_LEASE, 4);
+	if (IS_ERR_OR_NULL(cc))
 		return NULL;
 
-	data_offset = (char *)req + 4 + le32_to_cpu(req->CreateContextsOffset);
-	cc = (struct create_context *)data_offset;
-	do {
-		cc = (struct create_context *)((char *)cc + next);
-		name = le16_to_cpu(cc->NameOffset) + (char *)cc;
-		if (le16_to_cpu(cc->NameLength) != 4 ||
-		    strncmp(name, SMB2_CREATE_REQUEST_LEASE, 4)) {
-			next = le32_to_cpu(cc->Next);
-			continue;
-		}
-		found = true;
-		break;
-	} while (next != 0);
+	lreq = kzalloc(sizeof(struct lease_ctx_info), GFP_KERNEL);
+	if (!lreq)
+		return NULL;
 
-	if (found) {
-		if (sizeof(struct lease_context_v2) == le32_to_cpu(cc->DataLength)) {
-			struct create_lease_v2 *lc = (struct create_lease_v2 *)cc;
+	if (sizeof(struct lease_context_v2) == le32_to_cpu(cc->DataLength)) {
+		struct create_lease_v2 *lc = (struct create_lease_v2 *)cc;
 
-			*((__le64 *)lreq->lease_key) = lc->lcontext.LeaseKeyLow;
-			*((__le64 *)(lreq->lease_key + 8)) = lc->lcontext.LeaseKeyHigh;
+		memcpy(lreq->lease_key, lc->lcontext.LeaseKey, SMB2_LEASE_KEY_SIZE);
+		if (is_dir) {
+			lreq->req_state = lc->lcontext.LeaseState &
+				~SMB2_LEASE_WRITE_CACHING_LE;
+			lreq->is_dir = true;
+		} else
 			lreq->req_state = lc->lcontext.LeaseState;
-			lreq->flags = lc->lcontext.LeaseFlags;
-			lreq->duration = lc->lcontext.LeaseDuration;
-			*((__le64 *)lreq->parent_lease_key) = lc->lcontext.ParentLeaseKeyLow;
-			*((__le64 *)(lreq->parent_lease_key + 8)) = lc->lcontext.ParentLeaseKeyHigh;
-			lreq->version = 2;
-		} else {
-			struct create_lease *lc = (struct create_lease *)cc;
+		lreq->flags = lc->lcontext.LeaseFlags;
+		lreq->epoch = lc->lcontext.Epoch;
+		lreq->duration = lc->lcontext.LeaseDuration;
+		memcpy(lreq->parent_lease_key, lc->lcontext.ParentLeaseKey,
+				SMB2_LEASE_KEY_SIZE);
+		lreq->version = 2;
+	} else {
+		struct create_lease *lc = (struct create_lease *)cc;
 
-			*((__le64 *)lreq->lease_key) = lc->lcontext.LeaseKeyLow;
-			*((__le64 *)(lreq->lease_key + 8)) = lc->lcontext.LeaseKeyHigh;
-			lreq->req_state = lc->lcontext.LeaseState;
-			lreq->flags = lc->lcontext.LeaseFlags;
-			lreq->duration = lc->lcontext.LeaseDuration;
-			lreq->version = 1;
-		}
-		return lreq;
+		memcpy(lreq->lease_key, lc->lcontext.LeaseKey, SMB2_LEASE_KEY_SIZE);
+		lreq->req_state = lc->lcontext.LeaseState;
+		lreq->flags = lc->lcontext.LeaseFlags;
+		lreq->duration = lc->lcontext.LeaseDuration;
+		lreq->version = 1;
 	}
-
-	kfree(lreq);
-	return NULL;
+	return lreq;
 }
 
 /**
  * smb2_find_context_vals() - find a particular context info in open request
  * @open_req:	buffer containing smb2 file open(create) request
  * @tag:	context name to search for
+ * @tag_len:	the length of tag
  *
  * Return:	pointer to requested context, NULL if @str context not found
  *		or error pointer if name length is invalid.
  */
-struct create_context *smb2_find_context_vals(void *open_req, const char *tag)
+struct create_context *smb2_find_context_vals(void *open_req, const char *tag, int tag_len)
 {
 	struct create_context *cc;
 	unsigned int next = 0;
@@ -1462,7 +1564,7 @@
 	 * CreateContextsOffset and CreateContextsLength are guaranteed to
 	 * be valid because of ksmbd_smb2_check_message().
 	 */
-	cc = (struct create_context *)((char *)req + 4 +
+	cc = (struct create_context *)((char *)req +
 				       le32_to_cpu(req->CreateContextsOffset));
 	remain_len = le32_to_cpu(req->CreateContextsLength);
 	do {
@@ -1483,12 +1585,12 @@
 		    name_len < 4 ||
 		    name_off + name_len > cc_len ||
 		    (value_off & 0x7) != 0 ||
-		    (value_off && (value_off < name_off + name_len)) ||
+		    (value_len && value_off < name_off + (name_len < 8 ? 8 : name_len)) ||
 		    ((u64)value_off + value_len > cc_len))
 			return ERR_PTR(-EINVAL);
 
 		name = (char *)cc + name_off;
-		if (memcmp(name, tag, name_len) == 0)
+		if (name_len == tag_len && !memcmp(name, tag, name_len))
 			return cc;
 
 		remain_len -= next;
@@ -1610,7 +1712,11 @@
 	memset(buf, 0, sizeof(struct create_posix_rsp));
 	buf->ccontext.DataOffset = cpu_to_le16(offsetof
 			(struct create_posix_rsp, nlink));
-	buf->ccontext.DataLength = cpu_to_le32(52);
+	/*
+	 * DataLength = nlink(4) + reparse_tag(4) + mode(4) +
+	 * domain sid(28) + unix group sid(16).
+	 */
+	buf->ccontext.DataLength = cpu_to_le32(56);
 	buf->ccontext.NameOffset = cpu_to_le16(offsetof
 			(struct create_posix_rsp, Name));
 	buf->ccontext.NameLength = cpu_to_le16(POSIX_CTXT_DATA_LEN);
@@ -1634,13 +1740,20 @@
 
 	buf->nlink = cpu_to_le32(inode->i_nlink);
 	buf->reparse_tag = cpu_to_le32(fp->volatile_id);
-	buf->mode = cpu_to_le32(inode->i_mode);
+	buf->mode = cpu_to_le32(inode->i_mode & 0777);
+	/*
+	 * SidBuffer(44) contain two sids(Domain sid(28), UNIX group sid(16)).
+	 * Domain sid(28) = revision(1) + num_subauth(1) + authority(6) +
+	 *		    sub_auth(4 * 4(num_subauth)) + RID(4).
+	 * UNIX group id(16) = revision(1) + num_subauth(1) + authority(6) +
+	 *		       sub_auth(4 * 1(num_subauth)) + RID(4).
+	 */
 	id_to_sid(from_kuid_munged(&init_user_ns,
 				   i_uid_into_mnt(user_ns, inode)),
-		  SIDNFS_USER, (struct smb_sid *)&buf->SidBuffer[0]);
+		  SIDOWNER, (struct smb_sid *)&buf->SidBuffer[0]);
 	id_to_sid(from_kgid_munged(&init_user_ns,
 				   i_gid_into_mnt(user_ns, inode)),
-		  SIDNFS_GROUP, (struct smb_sid *)&buf->SidBuffer[20]);
+		  SIDUNIX_GROUP, (struct smb_sid *)&buf->SidBuffer[28]);
 }
 
 /*
@@ -1700,33 +1813,3 @@
 	read_unlock(&lease_list_lock);
 	return ret_op;
 }
-
-int smb2_check_durable_oplock(struct ksmbd_file *fp,
-			      struct lease_ctx_info *lctx, char *name)
-{
-	struct oplock_info *opinfo = opinfo_get(fp);
-	int ret = 0;
-
-	if (opinfo && opinfo->is_lease) {
-		if (!lctx) {
-			pr_err("open does not include lease\n");
-			ret = -EBADF;
-			goto out;
-		}
-		if (memcmp(opinfo->o_lease->lease_key, lctx->lease_key,
-			   SMB2_LEASE_KEY_SIZE)) {
-			pr_err("invalid lease key\n");
-			ret = -EBADF;
-			goto out;
-		}
-		if (name && strcmp(fp->filename, name)) {
-			pr_err("invalid name reconnect %s\n", name);
-			ret = -EINVAL;
-			goto out;
-		}
-	}
-out:
-	if (opinfo)
-		opinfo_put(opinfo);
-	return ret;
-}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/oplock.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/oplock.h
@@ -28,15 +28,15 @@
 #define OPLOCK_WRITE_TO_NONE		0x04
 #define OPLOCK_READ_TO_NONE		0x08
 
-#define SMB2_LEASE_KEY_SIZE		16
-
 struct lease_ctx_info {
 	__u8			lease_key[SMB2_LEASE_KEY_SIZE];
 	__le32			req_state;
 	__le32			flags;
 	__le64			duration;
 	__u8			parent_lease_key[SMB2_LEASE_KEY_SIZE];
+	__le16			epoch;
 	int			version;
+	bool			is_dir;
 };
 
 struct lease_table {
@@ -55,6 +55,7 @@
 	__u8			parent_lease_key[SMB2_LEASE_KEY_SIZE];
 	int			version;
 	unsigned short		epoch;
+	bool			is_dir;
 	struct lease_table	*l_lb;
 };
 
@@ -110,7 +111,7 @@
 
 /* Lease related functions */
 void create_lease_buf(u8 *rbuf, struct lease *lease);
-struct lease_ctx_info *parse_lease_state(void *open_req);
+struct lease_ctx_info *parse_lease_state(void *open_req, bool is_dir);
 __u8 smb2_map_lease_to_oplock(__le32 lease_state);
 int lease_read_to_write(struct oplock_info *opinfo);
 
@@ -120,12 +121,13 @@
 void create_mxac_rsp_buf(char *cc, int maximal_access);
 void create_disk_id_rsp_buf(char *cc, __u64 file_id, __u64 vol_id);
 void create_posix_rsp_buf(char *cc, struct ksmbd_file *fp);
-struct create_context *smb2_find_context_vals(void *open_req, const char *str);
+struct create_context *smb2_find_context_vals(void *open_req, const char *tag, int tag_len);
 struct oplock_info *lookup_lease_in_table(struct ksmbd_conn *conn,
 					  char *lease_key);
 int find_same_lease_key(struct ksmbd_session *sess, struct ksmbd_inode *ci,
 			struct lease_ctx_info *lctx);
 void destroy_lease_table(struct ksmbd_conn *conn);
-int smb2_check_durable_oplock(struct ksmbd_file *fp,
-			      struct lease_ctx_info *lctx, char *name);
+void smb_send_parent_lease_break_noti(struct ksmbd_file *fp,
+				      struct lease_ctx_info *lctx);
+void smb_lazy_parent_lease_break_close(struct ksmbd_file *fp);
 #endif /* __KSMBD_OPLOCK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/server.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/server.c
@@ -93,7 +93,8 @@
 {
 	struct smb_hdr *rsp_hdr;
 
-	if (ksmbd_conn_exiting(work) || ksmbd_conn_need_reconnect(work)) {
+	if (ksmbd_conn_exiting(work->conn) ||
+	    ksmbd_conn_need_reconnect(work->conn)) {
 		rsp_hdr = work->response_buf;
 		rsp_hdr->Status.CifsError = STATUS_CONNECTION_DISCONNECTED;
 		return 1;
@@ -114,8 +115,10 @@
 	if (check_conn_state(work))
 		return SERVER_HANDLER_CONTINUE;
 
-	if (ksmbd_verify_smb_message(work))
+	if (ksmbd_verify_smb_message(work)) {
+		conn->ops->set_rsp_status(work, STATUS_INVALID_PARAMETER);
 		return SERVER_HANDLER_ABORT;
+	}
 
 	command = conn->ops->get_cmd_val(work);
 	*cmd = command;
@@ -162,21 +165,19 @@
 {
 	u16 command = 0;
 	int rc;
-
-	if (conn->ops->allocate_rsp_buf(work))
-		return;
+	bool is_chained = false;
 
 	if (conn->ops->is_transform_hdr &&
 	    conn->ops->is_transform_hdr(work->request_buf)) {
 		rc = conn->ops->decrypt_req(work);
-		if (rc < 0) {
-			conn->ops->set_rsp_status(work, STATUS_DATA_ERROR);
-			goto send;
-		}
-
+		if (rc < 0)
+			return;
 		work->encrypted = true;
 	}
 
+	if (conn->ops->allocate_rsp_buf(work))
+		return;
+
 	rc = conn->ops->init_rsp_hdr(work);
 	if (rc) {
 		/* either uid or tid is not correct */
@@ -184,24 +185,31 @@
 		goto send;
 	}
 
-	if (conn->ops->check_user_session) {
-		rc = conn->ops->check_user_session(work);
-		if (rc < 0) {
-			command = conn->ops->get_cmd_val(work);
-			conn->ops->set_rsp_status(work,
-					STATUS_USER_SESSION_DELETED);
-			goto send;
-		} else if (rc > 0) {
-			rc = conn->ops->get_ksmbd_tcon(work);
+	do {
+		if (conn->ops->check_user_session) {
+			rc = conn->ops->check_user_session(work);
 			if (rc < 0) {
-				conn->ops->set_rsp_status(work,
-					STATUS_NETWORK_NAME_DELETED);
+				if (rc == -EINVAL)
+					conn->ops->set_rsp_status(work,
+						STATUS_INVALID_PARAMETER);
+				else
+					conn->ops->set_rsp_status(work,
+						STATUS_USER_SESSION_DELETED);
 				goto send;
+			} else if (rc > 0) {
+				rc = conn->ops->get_ksmbd_tcon(work);
+				if (rc < 0) {
+					if (rc == -EINVAL)
+						conn->ops->set_rsp_status(work,
+							STATUS_INVALID_PARAMETER);
+					else
+						conn->ops->set_rsp_status(work,
+							STATUS_NETWORK_NAME_DELETED);
+					goto send;
+				}
 			}
 		}
-	}
 
-	do {
 		rc = __process_request(work, conn, &command);
 		if (rc == SERVER_HANDLER_ABORT)
 			break;
@@ -221,25 +229,26 @@
 			}
 		}
 
+		is_chained = is_chained_smb2_message(work);
+
 		if (work->sess &&
 		    (work->sess->sign || smb3_11_final_sess_setup_resp(work) ||
 		     conn->ops->is_sign_req(work, command)))
 			conn->ops->set_sign_rsp(work);
-	} while (is_chained_smb2_message(work));
-
-	if (work->send_no_response)
-		return;
+	} while (is_chained == true);
 
 send:
+	if (work->tcon)
+		ksmbd_tree_connect_put(work->tcon);
 	smb3_preauth_hash_rsp(work);
 	if (work->sess && work->sess->enc && work->encrypted &&
 	    conn->ops->encrypt_resp) {
 		rc = conn->ops->encrypt_resp(work);
-		if (rc < 0) {
+		if (rc < 0)
 			conn->ops->set_rsp_status(work, STATUS_DATA_ERROR);
-			goto send;
-		}
 	}
+	if (work->sess)
+		ksmbd_user_session_put(work->sess);
 
 	ksmbd_conn_write(work);
 }
@@ -261,7 +270,13 @@
 
 	ksmbd_conn_try_dequeue_request(work);
 	ksmbd_free_work_struct(work);
-	atomic_dec(&conn->r_count);
+	/*
+	 * Checking waitqueue to dropping pending requests on
+	 * disconnection. waitqueue_active is safe because it
+	 * uses atomic operation for condition.
+	 */
+	if (!atomic_dec_return(&conn->r_count) && waitqueue_active(&conn->r_count_q))
+		wake_up(&conn->r_count_q);
 }
 
 /**
@@ -274,6 +289,7 @@
 static int queue_ksmbd_work(struct ksmbd_conn *conn)
 {
 	struct ksmbd_work *work;
+	int err;
 
 	work = ksmbd_alloc_work_struct();
 	if (!work) {
@@ -285,9 +301,10 @@
 	work->request_buf = conn->request_buf;
 	conn->request_buf = NULL;
 
-	if (ksmbd_init_smb_server(work)) {
+	err = ksmbd_init_smb_server(work);
+	if (err) {
 		ksmbd_free_work_struct(work);
-		return -EINVAL;
+		return 0;
 	}
 
 	ksmbd_conn_enqueue_request(work);
@@ -428,11 +445,9 @@
 		"reset",
 		"shutdown"
 	};
-
-	ssize_t sz = scnprintf(buf, PAGE_SIZE, "%d %s %d %lu\n", stats_version,
-			       state[server_conf.state], server_conf.tcp_port,
-			       server_conf.ipc_last_active / HZ);
-	return sz;
+	return sysfs_emit(buf, "%d %s %d %lu\n", stats_version,
+			  state[server_conf.state], server_conf.tcp_port,
+			  server_conf.ipc_last_active / HZ);
 }
 
 static ssize_t kill_server_store(struct class *class,
@@ -464,19 +479,13 @@
 
 	for (i = 0; i < ARRAY_SIZE(debug_type_strings); i++) {
 		if ((ksmbd_debug_types >> i) & 1) {
-			pos = scnprintf(buf + sz,
-					PAGE_SIZE - sz,
-					"[%s] ",
-					debug_type_strings[i]);
+			pos = sysfs_emit_at(buf, sz, "[%s] ", debug_type_strings[i]);
 		} else {
-			pos = scnprintf(buf + sz,
-					PAGE_SIZE - sz,
-					"%s ",
-					debug_type_strings[i]);
+			pos = sysfs_emit_at(buf, sz, "%s ", debug_type_strings[i]);
 		}
 		sz += pos;
 	}
-	sz += scnprintf(buf + sz, PAGE_SIZE - sz, "\n");
+	sz += sysfs_emit_at(buf, sz, "\n");
 	return sz;
 }
 
@@ -585,8 +594,6 @@
 	if (ret)
 		goto err_crypto_destroy;
 
-	pr_warn_once("The ksmbd server is experimental, use at your own risk.\n");
-
 	return 0;
 
 err_crypto_destroy:
@@ -613,6 +620,7 @@
 static void __exit ksmbd_server_exit(void)
 {
 	ksmbd_server_shutdown();
+	rcu_barrier();
 	ksmbd_release_inode_hash();
 }
 
@@ -622,7 +630,6 @@
 MODULE_LICENSE("GPL");
 MODULE_SOFTDEP("pre: ecb");
 MODULE_SOFTDEP("pre: hmac");
-MODULE_SOFTDEP("pre: md4");
 MODULE_SOFTDEP("pre: md5");
 MODULE_SOFTDEP("pre: nls");
 MODULE_SOFTDEP("pre: aes");
@@ -632,5 +639,6 @@
 MODULE_SOFTDEP("pre: aead2");
 MODULE_SOFTDEP("pre: ccm");
 MODULE_SOFTDEP("pre: gcm");
+MODULE_SOFTDEP("pre: crc32");
 module_init(ksmbd_server_init)
 module_exit(ksmbd_server_exit)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/server.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/server.h
@@ -41,6 +41,7 @@
 	unsigned int		share_fake_fscaps;
 	struct smb_sid		domain_sid;
 	unsigned int		auth_mechs;
+	unsigned int		max_connections;
 
 	char			*conf[SERVER_CONF_WORK_GROUP + 1];
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smb2misc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smb2misc.c
@@ -91,11 +91,6 @@
 	*off = 0;
 	*len = 0;
 
-	/* error reqeusts do not have data area */
-	if (hdr->Status && hdr->Status != STATUS_MORE_PROCESSING_REQUIRED &&
-	    (((struct smb2_err_rsp *)hdr)->StructureSize) == SMB2_ERROR_STRUCTURE_SIZE2_LE)
-		return ret;
-
 	/*
 	 * Following commands have data areas so we have to get the location
 	 * of the data buffer offset and data buffer length for the particular
@@ -107,29 +102,44 @@
 		*len = le16_to_cpu(((struct smb2_sess_setup_req *)hdr)->SecurityBufferLength);
 		break;
 	case SMB2_TREE_CONNECT:
-		*off = le16_to_cpu(((struct smb2_tree_connect_req *)hdr)->PathOffset);
+		*off = max_t(unsigned short int,
+			     le16_to_cpu(((struct smb2_tree_connect_req *)hdr)->PathOffset),
+			     offsetof(struct smb2_tree_connect_req, Buffer));
 		*len = le16_to_cpu(((struct smb2_tree_connect_req *)hdr)->PathLength);
 		break;
 	case SMB2_CREATE:
 	{
+		unsigned short int name_off =
+			le16_to_cpu(((struct smb2_create_req *)hdr)->NameOffset);
+		unsigned short int name_len =
+			le16_to_cpu(((struct smb2_create_req *)hdr)->NameLength);
+
 		if (((struct smb2_create_req *)hdr)->CreateContextsLength) {
 			*off = le32_to_cpu(((struct smb2_create_req *)
 				hdr)->CreateContextsOffset);
 			*len = le32_to_cpu(((struct smb2_create_req *)
 				hdr)->CreateContextsLength);
-			break;
+			if (!name_len)
+				break;
+
+			if (name_off + name_len < (u64)*off + *len)
+				break;
 		}
 
-		*off = le16_to_cpu(((struct smb2_create_req *)hdr)->NameOffset);
-		*len = le16_to_cpu(((struct smb2_create_req *)hdr)->NameLength);
+		*off = name_off;
+		*len = name_len;
 		break;
 	}
 	case SMB2_QUERY_INFO:
-		*off = le16_to_cpu(((struct smb2_query_info_req *)hdr)->InputBufferOffset);
+		*off = max_t(unsigned int,
+			     le16_to_cpu(((struct smb2_query_info_req *)hdr)->InputBufferOffset),
+			     offsetof(struct smb2_query_info_req, Buffer));
 		*len = le32_to_cpu(((struct smb2_query_info_req *)hdr)->InputBufferLength);
 		break;
 	case SMB2_SET_INFO:
-		*off = le16_to_cpu(((struct smb2_set_info_req *)hdr)->BufferOffset);
+		*off = max_t(unsigned int,
+			     le16_to_cpu(((struct smb2_set_info_req *)hdr)->BufferOffset),
+			     offsetof(struct smb2_set_info_req, Buffer));
 		*len = le32_to_cpu(((struct smb2_set_info_req *)hdr)->BufferLength);
 		break;
 	case SMB2_READ:
@@ -137,8 +147,11 @@
 		*len = le16_to_cpu(((struct smb2_read_req *)hdr)->ReadChannelInfoLength);
 		break;
 	case SMB2_WRITE:
-		if (((struct smb2_write_req *)hdr)->DataOffset) {
-			*off = le16_to_cpu(((struct smb2_write_req *)hdr)->DataOffset);
+		if (((struct smb2_write_req *)hdr)->DataOffset ||
+		    ((struct smb2_write_req *)hdr)->Length) {
+			*off = max_t(unsigned short int,
+				     le16_to_cpu(((struct smb2_write_req *)hdr)->DataOffset),
+				     offsetof(struct smb2_write_req, Buffer) - 4);
 			*len = le32_to_cpu(((struct smb2_write_req *)hdr)->Length);
 			break;
 		}
@@ -147,26 +160,26 @@
 		*len = le16_to_cpu(((struct smb2_write_req *)hdr)->WriteChannelInfoLength);
 		break;
 	case SMB2_QUERY_DIRECTORY:
-		*off = le16_to_cpu(((struct smb2_query_directory_req *)hdr)->FileNameOffset);
+		*off = max_t(unsigned short int,
+			     le16_to_cpu(((struct smb2_query_directory_req *)hdr)->FileNameOffset),
+			     offsetof(struct smb2_query_directory_req, Buffer));
 		*len = le16_to_cpu(((struct smb2_query_directory_req *)hdr)->FileNameLength);
 		break;
 	case SMB2_LOCK:
 	{
-		int lock_count;
+		unsigned short lock_count;
 
-		/*
-		 * smb2_lock request size is 48 included single
-		 * smb2_lock_element structure size.
-		 */
-		lock_count = le16_to_cpu(((struct smb2_lock_req *)hdr)->LockCount) - 1;
+		lock_count = le16_to_cpu(((struct smb2_lock_req *)hdr)->LockCount);
 		if (lock_count > 0) {
-			*off = __SMB2_HEADER_STRUCTURE_SIZE + 48;
+			*off = offsetof(struct smb2_lock_req, locks);
 			*len = sizeof(struct smb2_lock_element) * lock_count;
 		}
 		break;
 	}
 	case SMB2_IOCTL:
-		*off = le32_to_cpu(((struct smb2_ioctl_req *)hdr)->InputOffset);
+		*off = max_t(unsigned int,
+			     le32_to_cpu(((struct smb2_ioctl_req *)hdr)->InputOffset),
+			     offsetof(struct smb2_ioctl_req, Buffer));
 		*len = le32_to_cpu(((struct smb2_ioctl_req *)hdr)->InputCount);
 		break;
 	default:
@@ -290,7 +303,7 @@
 	unsigned int req_len = 0, expect_resp_len = 0, calc_credit_num, max_len;
 	unsigned short credit_charge = le16_to_cpu(hdr->CreditCharge);
 	void *__hdr = hdr;
-	int ret;
+	int ret = 0;
 
 	switch (hdr->Command) {
 	case SMB2_QUERY_INFO:
@@ -327,43 +340,49 @@
 		ksmbd_debug(SMB, "Insufficient credit charge, given: %d, needed: %d\n",
 			    credit_charge, calc_credit_num);
 		return 1;
-	} else if (credit_charge > conn->max_credits) {
+	} else if (credit_charge > conn->vals->max_credits) {
 		ksmbd_debug(SMB, "Too large credit charge: %d\n", credit_charge);
 		return 1;
 	}
 
 	spin_lock(&conn->credits_lock);
-	if (credit_charge <= conn->total_credits) {
-		conn->total_credits -= credit_charge;
-		ret = 0;
-	} else {
+	if (credit_charge > conn->total_credits) {
 		ksmbd_debug(SMB, "Insufficient credits granted, given: %u, granted: %u\n",
 			    credit_charge, conn->total_credits);
 		ret = 1;
 	}
+
+	if ((u64)conn->outstanding_credits + credit_charge > conn->total_credits) {
+		ksmbd_debug(SMB, "Limits exceeding the maximum allowable outstanding requests, given : %u, pending : %u\n",
+			    credit_charge, conn->outstanding_credits);
+		ret = 1;
+	} else
+		conn->outstanding_credits += credit_charge;
+
 	spin_unlock(&conn->credits_lock);
+
 	return ret;
 }
 
 int ksmbd_smb2_check_message(struct ksmbd_work *work)
 {
-	struct smb2_pdu *pdu = work->request_buf;
+	struct smb2_pdu *pdu = ksmbd_req_buf_next(work);
 	struct smb2_hdr *hdr = &pdu->hdr;
 	int command;
 	__u32 clc_len;  /* calculated length */
-	__u32 len = get_rfc1002_len(pdu);
+	__u32 len = get_rfc1002_len(work->request_buf);
+	__u32 req_struct_size, next_cmd = le32_to_cpu(hdr->NextCommand);
 
-	if (work->next_smb2_rcv_hdr_off) {
-		pdu = ksmbd_req_buf_next(work);
-		hdr = &pdu->hdr;
+	if ((u64)work->next_smb2_rcv_hdr_off + next_cmd > len) {
+		pr_err("next command(%u) offset exceeds smb msg size\n",
+				next_cmd);
+		return 1;
 	}
 
-	if (le32_to_cpu(hdr->NextCommand) > 0) {
-		len = le32_to_cpu(hdr->NextCommand);
-	} else if (work->next_smb2_rcv_hdr_off) {
+	if (next_cmd > 0)
+		len = next_cmd;
+	else if (work->next_smb2_rcv_hdr_off)
 		len -= work->next_smb2_rcv_hdr_off;
-		len = round_up(len, 8);
-	}
 
 	if (check_smb2_hdr(hdr))
 		return 1;
@@ -381,25 +400,25 @@
 	}
 
 	if (smb2_req_struct_sizes[command] != pdu->StructureSize2) {
-		if (command != SMB2_OPLOCK_BREAK_HE &&
-		    (hdr->Status == 0 || pdu->StructureSize2 != SMB2_ERROR_STRUCTURE_SIZE2_LE)) {
-			/* error packets have 9 byte structure size */
-			ksmbd_debug(SMB,
-				    "Illegal request size %u for command %d\n",
-				    le16_to_cpu(pdu->StructureSize2), command);
-			return 1;
-		} else if (command == SMB2_OPLOCK_BREAK_HE &&
-			   hdr->Status == 0 &&
-			   le16_to_cpu(pdu->StructureSize2) != OP_BREAK_STRUCT_SIZE_20 &&
-			   le16_to_cpu(pdu->StructureSize2) != OP_BREAK_STRUCT_SIZE_21) {
+		if (!(command == SMB2_OPLOCK_BREAK_HE &&
+		    (le16_to_cpu(pdu->StructureSize2) == OP_BREAK_STRUCT_SIZE_20 ||
+		    le16_to_cpu(pdu->StructureSize2) == OP_BREAK_STRUCT_SIZE_21))) {
 			/* special case for SMB2.1 lease break message */
 			ksmbd_debug(SMB,
-				    "Illegal request size %d for oplock break\n",
-				    le16_to_cpu(pdu->StructureSize2));
+				"Illegal request size %u for command %d\n",
+				le16_to_cpu(pdu->StructureSize2), command);
 			return 1;
 		}
 	}
 
+	req_struct_size = le16_to_cpu(pdu->StructureSize2) +
+		__SMB2_HEADER_STRUCTURE_SIZE;
+	if (command == SMB2_LOCK_HE)
+		req_struct_size -= sizeof(struct smb2_lock_element);
+
+	if (req_struct_size > len + 1)
+		return 1;
+
 	if (smb2_calc_size(hdr, &clc_len))
 		return 1;
 
@@ -416,20 +435,22 @@
 			goto validate_credit;
 
 		/*
-		 * windows client also pad up to 8 bytes when compounding.
-		 * If pad is longer than eight bytes, log the server behavior
-		 * (once), since may indicate a problem but allow it and
-		 * continue since the frame is parseable.
+		 * SMB2 NEGOTIATE request will be validated when message
+		 * handling proceeds.
 		 */
-		if (clc_len < len) {
-			ksmbd_debug(SMB,
-				    "cli req padded more than expected. Length %d not %d for cmd:%d mid:%llu\n",
-				    len, clc_len, command,
-				    le64_to_cpu(hdr->MessageId));
+		if (command == SMB2_NEGOTIATE_HE)
+			goto validate_credit;
+
+		/*
+		 * Allow a message that padded to 8byte boundary.
+		 * Linux 4.19.217 with smb 3.0.2 are sometimes
+		 * sending messages where the cls_len is exactly
+		 * 8 bytes less than len.
+		 */
+		if (clc_len < len && (len - clc_len) <= 8)
 			goto validate_credit;
-		}
 
-		ksmbd_debug(SMB,
+		pr_err_ratelimited(
 			    "cli req too short, len %d not %d. cmd:%d mid:%llu\n",
 			    len, clc_len, command,
 			    le64_to_cpu(hdr->MessageId));
@@ -439,10 +460,8 @@
 
 validate_credit:
 	if ((work->conn->vals->capabilities & SMB2_GLOBAL_CAP_LARGE_MTU) &&
-	    smb2_validate_credit_charge(work->conn, hdr)) {
-		work->conn->ops->set_rsp_status(work, STATUS_INVALID_PARAMETER);
+	    smb2_validate_credit_charge(work->conn, hdr))
 		return 1;
-	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smb2ops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smb2ops.c
@@ -20,6 +20,7 @@
 	.max_read_size = SMB21_DEFAULT_IOSIZE,
 	.max_write_size = SMB21_DEFAULT_IOSIZE,
 	.max_trans_size = SMB21_DEFAULT_IOSIZE,
+	.max_credits = SMB2_MAX_CREDITS,
 	.large_lock_type = 0,
 	.exclusive_lock_type = SMB2_LOCKFLAG_EXCLUSIVE,
 	.shared_lock_type = SMB2_LOCKFLAG_SHARED,
@@ -45,6 +46,7 @@
 	.max_read_size = SMB3_DEFAULT_IOSIZE,
 	.max_write_size = SMB3_DEFAULT_IOSIZE,
 	.max_trans_size = SMB3_DEFAULT_TRANS_SIZE,
+	.max_credits = SMB2_MAX_CREDITS,
 	.large_lock_type = 0,
 	.exclusive_lock_type = SMB2_LOCKFLAG_EXCLUSIVE,
 	.shared_lock_type = SMB2_LOCKFLAG_SHARED,
@@ -71,6 +73,7 @@
 	.max_read_size = SMB3_DEFAULT_IOSIZE,
 	.max_write_size = SMB3_DEFAULT_IOSIZE,
 	.max_trans_size = SMB3_DEFAULT_TRANS_SIZE,
+	.max_credits = SMB2_MAX_CREDITS,
 	.large_lock_type = 0,
 	.exclusive_lock_type = SMB2_LOCKFLAG_EXCLUSIVE,
 	.shared_lock_type = SMB2_LOCKFLAG_SHARED,
@@ -97,6 +100,7 @@
 	.max_read_size = SMB3_DEFAULT_IOSIZE,
 	.max_write_size = SMB3_DEFAULT_IOSIZE,
 	.max_trans_size = SMB3_DEFAULT_TRANS_SIZE,
+	.max_credits = SMB2_MAX_CREDITS,
 	.large_lock_type = 0,
 	.exclusive_lock_type = SMB2_LOCKFLAG_EXCLUSIVE,
 	.shared_lock_type = SMB2_LOCKFLAG_SHARED,
@@ -198,7 +202,6 @@
 	conn->ops = &smb2_0_server_ops;
 	conn->cmds = smb2_0_server_cmds;
 	conn->max_cmds = ARRAY_SIZE(smb2_0_server_cmds);
-	conn->max_credits = SMB2_MAX_CREDITS;
 	conn->signing_algorithm = SIGNING_ALG_HMAC_SHA256;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_LEASES)
@@ -216,16 +219,21 @@
 	conn->ops = &smb3_0_server_ops;
 	conn->cmds = smb2_0_server_cmds;
 	conn->max_cmds = ARRAY_SIZE(smb2_0_server_cmds);
-	conn->max_credits = SMB2_MAX_CREDITS;
 	conn->signing_algorithm = SIGNING_ALG_AES_CMAC;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_LEASES)
-		conn->vals->capabilities |= SMB2_GLOBAL_CAP_LEASING;
+		conn->vals->capabilities |= SMB2_GLOBAL_CAP_LEASING |
+			SMB2_GLOBAL_CAP_DIRECTORY_LEASING;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION &&
 	    conn->cli_cap & SMB2_GLOBAL_CAP_ENCRYPTION)
 		conn->vals->capabilities |= SMB2_GLOBAL_CAP_ENCRYPTION;
 
+	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION ||
+	    (!(server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION_OFF) &&
+	     conn->cli_cap & SMB2_GLOBAL_CAP_ENCRYPTION))
+		conn->vals->capabilities |= SMB2_GLOBAL_CAP_ENCRYPTION;
+
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB3_MULTICHANNEL)
 		conn->vals->capabilities |= SMB2_GLOBAL_CAP_MULTI_CHANNEL;
 }
@@ -241,14 +249,15 @@
 	conn->ops = &smb3_0_server_ops;
 	conn->cmds = smb2_0_server_cmds;
 	conn->max_cmds = ARRAY_SIZE(smb2_0_server_cmds);
-	conn->max_credits = SMB2_MAX_CREDITS;
 	conn->signing_algorithm = SIGNING_ALG_AES_CMAC;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_LEASES)
-		conn->vals->capabilities |= SMB2_GLOBAL_CAP_LEASING;
+		conn->vals->capabilities |= SMB2_GLOBAL_CAP_LEASING |
+			SMB2_GLOBAL_CAP_DIRECTORY_LEASING;
 
-	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION &&
-	    conn->cli_cap & SMB2_GLOBAL_CAP_ENCRYPTION)
+	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION ||
+	    (!(server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION_OFF) &&
+	     conn->cli_cap & SMB2_GLOBAL_CAP_ENCRYPTION))
 		conn->vals->capabilities |= SMB2_GLOBAL_CAP_ENCRYPTION;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB3_MULTICHANNEL)
@@ -266,14 +275,11 @@
 	conn->ops = &smb3_11_server_ops;
 	conn->cmds = smb2_0_server_cmds;
 	conn->max_cmds = ARRAY_SIZE(smb2_0_server_cmds);
-	conn->max_credits = SMB2_MAX_CREDITS;
 	conn->signing_algorithm = SIGNING_ALG_AES_CMAC;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_LEASES)
-		conn->vals->capabilities |= SMB2_GLOBAL_CAP_LEASING;
-
-	if (conn->cipher_type)
-		conn->vals->capabilities |= SMB2_GLOBAL_CAP_ENCRYPTION;
+		conn->vals->capabilities |= SMB2_GLOBAL_CAP_LEASING |
+			SMB2_GLOBAL_CAP_DIRECTORY_LEASING;
 
 	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB3_MULTICHANNEL)
 		conn->vals->capabilities |= SMB2_GLOBAL_CAP_MULTI_CHANNEL;
@@ -308,3 +314,11 @@
 	smb302_server_values.max_trans_size = sz;
 	smb311_server_values.max_trans_size = sz;
 }
+
+void init_smb2_max_credits(unsigned int sz)
+{
+	smb21_server_values.max_credits = sz;
+	smb30_server_values.max_credits = sz;
+	smb302_server_values.max_credits = sz;
+	smb311_server_values.max_credits = sz;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smb2pdu.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smb2pdu.c
@@ -11,6 +11,7 @@
 #include <linux/statfs.h>
 #include <linux/ethtool.h>
 #include <linux/falloc.h>
+#include <linux/mount.h>
 
 #include "glob.h"
 #include "smb2pdu.h"
@@ -44,8 +45,8 @@
 		*req = ksmbd_req_buf_next(work);
 		*rsp = ksmbd_resp_buf_next(work);
 	} else {
-		*req = work->request_buf;
-		*rsp = work->response_buf;
+		*req = smb2_get_msg(work->request_buf);
+		*rsp = smb2_get_msg(work->response_buf);
 	}
 }
 
@@ -66,22 +67,17 @@
 		return false;
 
 	sess = ksmbd_session_lookup_all(conn, id);
-	if (sess)
+	if (sess) {
+		ksmbd_user_session_put(sess);
 		return true;
+	}
 	pr_err("Invalid user session id: %llu\n", id);
 	return false;
 }
 
 struct channel *lookup_chann_list(struct ksmbd_session *sess, struct ksmbd_conn *conn)
 {
-	struct channel *chann;
-
-	list_for_each_entry(chann, &sess->ksmbd_chann_list, chann_list) {
-		if (chann->conn == conn)
-			return chann;
-	}
-
-	return NULL;
+	return xa_load(&sess->ksmbd_chann_list, (long)conn);
 }
 
 /**
@@ -93,13 +89,13 @@
  */
 int smb2_get_ksmbd_tcon(struct ksmbd_work *work)
 {
-	struct smb2_hdr *req_hdr = work->request_buf;
-	int tree_id;
+	struct smb2_hdr *req_hdr = ksmbd_req_buf_next(work);
+	unsigned int cmd = le16_to_cpu(req_hdr->Command);
+	unsigned int tree_id;
 
-	work->tcon = NULL;
-	if (work->conn->ops->get_cmd_val(work) == SMB2_TREE_CONNECT_HE ||
-	    work->conn->ops->get_cmd_val(work) ==  SMB2_CANCEL_HE ||
-	    work->conn->ops->get_cmd_val(work) ==  SMB2_LOGOFF_HE) {
+	if (cmd == SMB2_TREE_CONNECT_HE ||
+	    cmd ==  SMB2_CANCEL_HE ||
+	    cmd ==  SMB2_LOGOFF_HE) {
 		ksmbd_debug(SMB, "skip to check tree connect request\n");
 		return 0;
 	}
@@ -110,10 +106,28 @@
 	}
 
 	tree_id = le32_to_cpu(req_hdr->Id.SyncId.TreeId);
+
+	/*
+	 * If request is not the first in Compound request,
+	 * Just validate tree id in header with work->tcon->id.
+	 */
+	if (work->next_smb2_rcv_hdr_off) {
+		if (!work->tcon) {
+			pr_err("The first operation in the compound does not have tcon\n");
+			return -EINVAL;
+		}
+		if (tree_id != UINT_MAX && work->tcon->id != tree_id) {
+			pr_err("tree id(%u) is different with id(%u) in first operation\n",
+					tree_id, work->tcon->id);
+			return -EINVAL;
+		}
+		return 1;
+	}
+
 	work->tcon = ksmbd_tree_conn_lookup(work->sess, tree_id);
 	if (!work->tcon) {
 		pr_err("Invalid tid %d\n", tree_id);
-		return -EINVAL;
+		return -ENOENT;
 	}
 
 	return 1;
@@ -130,15 +144,21 @@
 	if (work->next_smb2_rcv_hdr_off)
 		err_rsp = ksmbd_resp_buf_next(work);
 	else
-		err_rsp = work->response_buf;
+		err_rsp = smb2_get_msg(work->response_buf);
 
 	if (err_rsp->hdr.Status != STATUS_STOPPED_ON_SYMLINK) {
+		int err;
+
 		err_rsp->StructureSize = SMB2_ERROR_STRUCTURE_SIZE2_LE;
 		err_rsp->ErrorContextCount = 0;
 		err_rsp->Reserved = 0;
 		err_rsp->ByteCount = 0;
 		err_rsp->ErrorData[0] = 0;
-		inc_rfc1001_len(work->response_buf, SMB2_ERROR_STRUCTURE_SIZE2);
+		err = ksmbd_iov_pin_rsp(work, (void *)err_rsp,
+					__SMB2_HEADER_STRUCTURE_SIZE +
+						SMB2_ERROR_STRUCTURE_SIZE2);
+		if (err)
+			work->send_no_response = 1;
 	}
 }
 
@@ -150,7 +170,7 @@
  */
 bool is_smb2_neg_cmd(struct ksmbd_work *work)
 {
-	struct smb2_hdr *hdr = work->request_buf;
+	struct smb2_hdr *hdr = smb2_get_msg(work->request_buf);
 
 	/* is it SMB2 header ? */
 	if (hdr->ProtocolId != SMB2_PROTO_NUMBER)
@@ -174,7 +194,7 @@
  */
 bool is_smb2_rsp(struct ksmbd_work *work)
 {
-	struct smb2_hdr *hdr = work->response_buf;
+	struct smb2_hdr *hdr = smb2_get_msg(work->response_buf);
 
 	/* is it SMB2 header ? */
 	if (hdr->ProtocolId != SMB2_PROTO_NUMBER)
@@ -200,7 +220,7 @@
 	if (work->next_smb2_rcv_hdr_off)
 		rcv_hdr = ksmbd_req_buf_next(work);
 	else
-		rcv_hdr = work->request_buf;
+		rcv_hdr = smb2_get_msg(work->request_buf);
 	return le16_to_cpu(rcv_hdr->Command);
 }
 
@@ -213,11 +233,12 @@
 {
 	struct smb2_hdr *rsp_hdr;
 
-	if (work->next_smb2_rcv_hdr_off)
-		rsp_hdr = ksmbd_resp_buf_next(work);
-	else
-		rsp_hdr = work->response_buf;
+	rsp_hdr = smb2_get_msg(work->response_buf);
 	rsp_hdr->Status = err;
+
+	work->iov_idx = 0;
+	work->iov_cnt = 0;
+	work->next_smb2_rcv_hdr_off = 0;
 	smb2_set_err_rsp(work);
 }
 
@@ -233,17 +254,10 @@
 	struct smb2_hdr *rsp_hdr;
 	struct smb2_negotiate_rsp *rsp;
 	struct ksmbd_conn *conn = work->conn;
+	int err;
 
-	if (conn->need_neg == false)
-		return -EINVAL;
-
-	rsp_hdr = work->response_buf;
-
+	rsp_hdr = smb2_get_msg(work->response_buf);
 	memset(rsp_hdr, 0, sizeof(struct smb2_hdr) + 2);
-
-	rsp_hdr->smb2_buf_length =
-		cpu_to_be32(smb2_hdr_size_no_buflen(conn->vals));
-
 	rsp_hdr->ProtocolId = SMB2_PROTO_NUMBER;
 	rsp_hdr->StructureSize = SMB2_HEADER_STRUCTURE_SIZE;
 	rsp_hdr->CreditRequest = cpu_to_le16(2);
@@ -256,9 +270,9 @@
 	rsp_hdr->SessionId = 0;
 	memset(rsp_hdr->Signature, 0, 16);
 
-	rsp = work->response_buf;
+	rsp = smb2_get_msg(work->response_buf);
 
-	WARN_ON(ksmbd_conn_good(work));
+	WARN_ON(ksmbd_conn_good(conn));
 
 	rsp->StructureSize = cpu_to_le16(65);
 	ksmbd_debug(SMB, "conn->dialect 0x%x\n", conn->dialect);
@@ -277,18 +291,19 @@
 
 	rsp->SecurityBufferOffset = cpu_to_le16(128);
 	rsp->SecurityBufferLength = cpu_to_le16(AUTH_GSS_LENGTH);
-	ksmbd_copy_gss_neg_header(((char *)(&rsp->hdr) +
-		sizeof(rsp->hdr.smb2_buf_length)) +
+	ksmbd_copy_gss_neg_header((char *)(&rsp->hdr) +
 		le16_to_cpu(rsp->SecurityBufferOffset));
-	inc_rfc1001_len(rsp, sizeof(struct smb2_negotiate_rsp) -
-		sizeof(struct smb2_hdr) - sizeof(rsp->Buffer) +
-		AUTH_GSS_LENGTH);
 	rsp->SecurityMode = SMB2_NEGOTIATE_SIGNING_ENABLED_LE;
 	if (server_conf.signing == KSMBD_CONFIG_OPT_MANDATORY)
 		rsp->SecurityMode |= SMB2_NEGOTIATE_SIGNING_REQUIRED_LE;
+	err = ksmbd_iov_pin_rsp(work, rsp,
+				sizeof(struct smb2_negotiate_rsp) -
+				sizeof(rsp->Buffer) + AUTH_GSS_LENGTH);
+	if (err)
+		return err;
 	conn->use_spnego = true;
 
-	ksmbd_conn_set_need_negotiate(work);
+	ksmbd_conn_set_need_negotiate(conn);
 	return 0;
 }
 
@@ -301,16 +316,15 @@
 	struct smb2_hdr *req_hdr = ksmbd_req_buf_next(work);
 	struct smb2_hdr *hdr = ksmbd_resp_buf_next(work);
 	struct ksmbd_conn *conn = work->conn;
-	unsigned short credits_requested;
+	unsigned short credits_requested, aux_max;
 	unsigned short credit_charge, credits_granted = 0;
-	unsigned short aux_max, aux_credits;
 
 	if (work->send_no_response)
 		return 0;
 
 	hdr->CreditCharge = req_hdr->CreditCharge;
 
-	if (conn->total_credits > conn->max_credits) {
+	if (conn->total_credits > conn->vals->max_credits) {
 		hdr->CreditRequest = 0;
 		pr_err("Total credits overflow: %d\n", conn->total_credits);
 		return -EINVAL;
@@ -318,6 +332,14 @@
 
 	credit_charge = max_t(unsigned short,
 			      le16_to_cpu(req_hdr->CreditCharge), 1);
+	if (credit_charge > conn->total_credits) {
+		ksmbd_debug(SMB, "Insufficient credits granted, given: %u, granted: %u\n",
+			    credit_charge, conn->total_credits);
+		return -EINVAL;
+	}
+
+	conn->total_credits -= credit_charge;
+	conn->outstanding_credits -= credit_charge;
 	credits_requested = max_t(unsigned short,
 				  le16_to_cpu(req_hdr->CreditRequest), 1);
 
@@ -327,17 +349,11 @@
 	 * TODO: Need to adjuct CreditRequest value according to
 	 * current cpu load
 	 */
-	aux_credits = credits_requested - 1;
 	if (hdr->Command == SMB2_NEGOTIATE)
-		aux_max = 0;
+		aux_max = 1;
 	else
-		aux_max = conn->max_credits - credit_charge;
-	aux_credits = min_t(unsigned short, aux_credits, aux_max);
-	credits_granted = credit_charge + aux_credits;
-
-	if (conn->max_credits - conn->total_credits < credits_granted)
-		credits_granted = conn->max_credits -
-			conn->total_credits;
+		aux_max = conn->vals->max_credits - conn->total_credits;
+	credits_granted = min_t(unsigned short, credits_requested, aux_max);
 
 	conn->total_credits += credits_granted;
 	work->credits_granted += credits_granted;
@@ -374,12 +390,8 @@
 	 * command in the compound request
 	 */
 	if (req->Command == SMB2_CREATE && rsp->Status == STATUS_SUCCESS) {
-		work->compound_fid =
-			le64_to_cpu(((struct smb2_create_rsp *)rsp)->
-				VolatileFileId);
-		work->compound_pfid =
-			le64_to_cpu(((struct smb2_create_rsp *)rsp)->
-				PersistentFileId);
+		work->compound_fid = ((struct smb2_create_rsp *)rsp)->VolatileFileId;
+		work->compound_pfid = ((struct smb2_create_rsp *)rsp)->PersistentFileId;
 		work->compound_sid = le64_to_cpu(rsp->SessionId);
 	}
 
@@ -387,11 +399,12 @@
 	next_hdr_offset = le32_to_cpu(req->NextCommand);
 
 	new_len = ALIGN(len, 8);
-	inc_rfc1001_len(work->response_buf, ((sizeof(struct smb2_hdr) - 4)
-			+ new_len - len));
+	work->iov[work->iov_idx].iov_len += (new_len - len);
+	inc_rfc1001_len(work->response_buf, new_len - len);
 	rsp->NextCommand = cpu_to_le32(new_len);
 
 	work->next_smb2_rcv_hdr_off += next_hdr_offset;
+	work->curr_smb2_rsp_hdr_off = work->next_smb2_rsp_hdr_off;
 	work->next_smb2_rsp_hdr_off += new_len;
 	ksmbd_debug(SMB,
 		    "Compound req new_len = %d rcv off = %d rsp off = %d\n",
@@ -406,7 +419,7 @@
 		work->compound_fid = KSMBD_NO_FID;
 		work->compound_pfid = KSMBD_NO_FID;
 	}
-	memset((char *)rsp_hdr + 4, 0, sizeof(struct smb2_hdr) + 2);
+	memset((char *)rsp_hdr, 0, sizeof(struct smb2_hdr) + 2);
 	rsp_hdr->ProtocolId = SMB2_PROTO_NUMBER;
 	rsp_hdr->StructureSize = SMB2_HEADER_STRUCTURE_SIZE;
 	rsp_hdr->Command = rcv_hdr->Command;
@@ -432,7 +445,7 @@
  */
 bool is_chained_smb2_message(struct ksmbd_work *work)
 {
-	struct smb2_hdr *hdr = work->request_buf;
+	struct smb2_hdr *hdr = smb2_get_msg(work->request_buf);
 	unsigned int len, next_cmd;
 
 	if (hdr->ProtocolId != SMB2_PROTO_NUMBER)
@@ -467,10 +480,10 @@
 		len = len - get_rfc1002_len(work->response_buf);
 		if (len) {
 			ksmbd_debug(SMB, "padding len %u\n", len);
+			work->iov[work->iov_idx].iov_len += len;
 			inc_rfc1001_len(work->response_buf, len);
-			if (work->aux_payload_sz)
-				work->aux_payload_sz += len;
 		}
+		work->curr_smb2_rsp_hdr_off = work->next_smb2_rsp_hdr_off;
 	}
 	return false;
 }
@@ -483,13 +496,10 @@
  */
 int init_smb2_rsp_hdr(struct ksmbd_work *work)
 {
-	struct smb2_hdr *rsp_hdr = work->response_buf;
-	struct smb2_hdr *rcv_hdr = work->request_buf;
-	struct ksmbd_conn *conn = work->conn;
+	struct smb2_hdr *rsp_hdr = smb2_get_msg(work->response_buf);
+	struct smb2_hdr *rcv_hdr = smb2_get_msg(work->request_buf);
 
 	memset(rsp_hdr, 0, sizeof(struct smb2_hdr) + 2);
-	rsp_hdr->smb2_buf_length =
-		cpu_to_be32(smb2_hdr_size_no_buflen(conn->vals));
 	rsp_hdr->ProtocolId = rcv_hdr->ProtocolId;
 	rsp_hdr->StructureSize = SMB2_HEADER_STRUCTURE_SIZE;
 	rsp_hdr->Command = rcv_hdr->Command;
@@ -505,12 +515,6 @@
 	rsp_hdr->SessionId = rcv_hdr->SessionId;
 	memcpy(rsp_hdr->Signature, rcv_hdr->Signature, 16);
 
-	work->syncronous = true;
-	if (work->async_id) {
-		ksmbd_release_id(&conn->async_ida, work->async_id);
-		work->async_id = 0;
-	}
-
 	return 0;
 }
 
@@ -522,7 +526,7 @@
  */
 int smb2_allocate_rsp_buf(struct ksmbd_work *work)
 {
-	struct smb2_hdr *hdr = work->request_buf;
+	struct smb2_hdr *hdr = smb2_get_msg(work->request_buf);
 	size_t small_sz = MAX_CIFS_SMALL_BUFFER_SIZE;
 	size_t large_sz = small_sz + work->conn->vals->max_trans_size;
 	size_t sz = small_sz;
@@ -534,10 +538,15 @@
 	if (cmd == SMB2_QUERY_INFO_HE) {
 		struct smb2_query_info_req *req;
 
-		req = work->request_buf;
-		if (req->InfoType == SMB2_O_INFO_FILE &&
-		    (req->FileInfoClass == FILE_FULL_EA_INFORMATION ||
-		     req->FileInfoClass == FILE_ALL_INFORMATION))
+		if (get_rfc1002_len(work->request_buf) <
+		    offsetof(struct smb2_query_info_req, OutputBufferLength))
+			return -EINVAL;
+
+		req = smb2_get_msg(work->request_buf);
+		if ((req->InfoType == SMB2_O_INFO_FILE &&
+		     (req->FileInfoClass == FILE_FULL_EA_INFORMATION ||
+		      req->FileInfoClass == FILE_ALL_INFORMATION)) ||
+		    req->InfoType == SMB2_O_INFO_SECURITY)
 			sz = large_sz;
 	}
 
@@ -545,7 +554,7 @@
 	if (le32_to_cpu(hdr->NextCommand) > 0)
 		sz = large_sz;
 
-	work->response_buf = kvmalloc(sz, GFP_KERNEL | __GFP_ZERO);
+	work->response_buf = kvzalloc(sz, GFP_KERNEL);
 	if (!work->response_buf)
 		return -ENOMEM;
 
@@ -561,12 +570,11 @@
  */
 int smb2_check_user_session(struct ksmbd_work *work)
 {
-	struct smb2_hdr *req_hdr = work->request_buf;
+	struct smb2_hdr *req_hdr = ksmbd_req_buf_next(work);
 	struct ksmbd_conn *conn = work->conn;
-	unsigned int cmd = conn->ops->get_cmd_val(work);
+	unsigned int cmd = le16_to_cpu(req_hdr->Command);
 	unsigned long long sess_id;
 
-	work->sess = NULL;
 	/*
 	 * SMB2_ECHO, SMB2_NEGOTIATE, SMB2_SESSION_SETUP command do not
 	 * require a session id, so no need to validate user session's for
@@ -576,22 +584,43 @@
 	    cmd == SMB2_SESSION_SETUP_HE)
 		return 0;
 
-	if (!ksmbd_conn_good(work))
+	if (!ksmbd_conn_good(conn))
 		return -EINVAL;
 
 	sess_id = le64_to_cpu(req_hdr->SessionId);
+
+	/*
+	 * If request is not the first in Compound request,
+	 * Just validate session id in header with work->sess->id.
+	 */
+	if (work->next_smb2_rcv_hdr_off) {
+		if (!work->sess) {
+			pr_err("The first operation in the compound does not have sess\n");
+			return -EINVAL;
+		}
+		if (sess_id != ULLONG_MAX && work->sess->id != sess_id) {
+			pr_err("session id(%llu) is different with the first operation(%lld)\n",
+					sess_id, work->sess->id);
+			return -EINVAL;
+		}
+		return 1;
+	}
+
 	/* Check for validity of user session */
 	work->sess = ksmbd_session_lookup_all(conn, sess_id);
 	if (work->sess)
 		return 1;
 	ksmbd_debug(SMB, "Invalid user session, Uid %llu\n", sess_id);
-	return -EINVAL;
+	return -ENOENT;
 }
 
-static void destroy_previous_session(struct ksmbd_user *user, u64 id)
+static void destroy_previous_session(struct ksmbd_conn *conn,
+				     struct ksmbd_user *user, u64 id)
 {
 	struct ksmbd_session *prev_sess = ksmbd_session_lookup_slowpath(id);
 	struct ksmbd_user *prev_user;
+	struct channel *chann;
+	long index;
 
 	if (!prev_sess)
 		return;
@@ -601,27 +630,24 @@
 	if (!prev_user ||
 	    strcmp(user->name, prev_user->name) ||
 	    user->passkey_sz != prev_user->passkey_sz ||
-	    memcmp(user->passkey, prev_user->passkey, user->passkey_sz)) {
-		put_session(prev_sess);
+	    memcmp(user->passkey, prev_user->passkey, user->passkey_sz))
 		return;
-	}
 
-	put_session(prev_sess);
-	ksmbd_session_destroy(prev_sess);
+	prev_sess->state = SMB2_SESSION_EXPIRED;
+	xa_for_each(&prev_sess->ksmbd_chann_list, index, chann)
+		ksmbd_conn_set_exiting(chann->conn);
 }
 
 /**
  * smb2_get_name() - get filename string from on the wire smb format
- * @share:	ksmbd_share_config pointer
  * @src:	source buffer
  * @maxlen:	maxlen of source string
- * @nls_table:	nls_table pointer
+ * @local_nls:	nls_table pointer
  *
  * Return:      matching converted filename on success, otherwise error ptr
  */
 static char *
-smb2_get_name(struct ksmbd_share_config *share, const char *src,
-	      const int maxlen, struct nls_table *local_nls)
+smb2_get_name(const char *src, const int maxlen, struct nls_table *local_nls)
 {
 	char *name;
 
@@ -638,21 +664,16 @@
 
 int setup_async_work(struct ksmbd_work *work, void (*fn)(void **), void **arg)
 {
-	struct smb2_hdr *rsp_hdr;
 	struct ksmbd_conn *conn = work->conn;
 	int id;
 
-	rsp_hdr = work->response_buf;
-	rsp_hdr->Flags |= SMB2_FLAGS_ASYNC_COMMAND;
-
 	id = ksmbd_acquire_async_msg_id(&conn->async_ida);
 	if (id < 0) {
 		pr_err("Failed to alloc async message id\n");
 		return id;
 	}
-	work->syncronous = false;
+	work->asynchronous = true;
 	work->async_id = id;
-	rsp_hdr->Id.AsyncId = cpu_to_le64(id);
 
 	ksmbd_debug(SMB,
 		    "Send interim Response to inform async request id : %d\n",
@@ -670,18 +691,50 @@
 	return 0;
 }
 
+void release_async_work(struct ksmbd_work *work)
+{
+	struct ksmbd_conn *conn = work->conn;
+
+	spin_lock(&conn->request_lock);
+	list_del_init(&work->async_request_entry);
+	spin_unlock(&conn->request_lock);
+
+	work->asynchronous = 0;
+	work->cancel_fn = NULL;
+	kfree(work->cancel_argv);
+	work->cancel_argv = NULL;
+	if (work->async_id) {
+		ksmbd_release_id(&conn->async_ida, work->async_id);
+		work->async_id = 0;
+	}
+}
+
 void smb2_send_interim_resp(struct ksmbd_work *work, __le32 status)
 {
 	struct smb2_hdr *rsp_hdr;
+	struct ksmbd_work *in_work = ksmbd_alloc_work_struct();
 
-	rsp_hdr = work->response_buf;
-	smb2_set_err_rsp(work);
+	if (!in_work)
+		return;
+
+	if (allocate_interim_rsp_buf(in_work)) {
+		pr_err("smb_allocate_rsp_buf failed!\n");
+		ksmbd_free_work_struct(in_work);
+		return;
+	}
+
+	in_work->conn = work->conn;
+	memcpy(smb2_get_msg(in_work->response_buf), ksmbd_resp_buf_next(work),
+	       __SMB2_HEADER_STRUCTURE_SIZE);
+
+	rsp_hdr = smb2_get_msg(in_work->response_buf);
+	rsp_hdr->Flags |= SMB2_FLAGS_ASYNC_COMMAND;
+	rsp_hdr->Id.AsyncId = cpu_to_le64(work->async_id);
+	smb2_set_err_rsp(in_work);
 	rsp_hdr->Status = status;
 
-	work->multiRsp = 1;
-	ksmbd_conn_write(work);
-	rsp_hdr->Status = 0;
-	work->multiRsp = 0;
+	ksmbd_conn_write(in_work);
+	ksmbd_free_work_struct(in_work);
 }
 
 static __le32 smb2_get_reparse_tag_special_file(umode_t mode)
@@ -753,19 +806,6 @@
 	pneg_ctxt->Ciphers[0] = cipher_type;
 }
 
-static void build_compression_ctxt(struct smb2_compression_ctx *pneg_ctxt,
-				   __le16 comp_algo)
-{
-	pneg_ctxt->ContextType = SMB2_COMPRESSION_CAPABILITIES;
-	pneg_ctxt->DataLength =
-		cpu_to_le16(sizeof(struct smb2_compression_ctx)
-			- sizeof(struct smb2_neg_context));
-	pneg_ctxt->Reserved = cpu_to_le32(0);
-	pneg_ctxt->CompressionAlgorithmCount = cpu_to_le16(1);
-	pneg_ctxt->Reserved1 = cpu_to_le32(0);
-	pneg_ctxt->CompressionAlgorithms[0] = comp_algo;
-}
-
 static void build_sign_cap_ctxt(struct smb2_signing_capabilities *pneg_ctxt,
 				__le16 sign_algo)
 {
@@ -801,12 +841,11 @@
 	pneg_ctxt->Name[15] = 0x7C;
 }
 
-static void assemble_neg_contexts(struct ksmbd_conn *conn,
+static unsigned int assemble_neg_contexts(struct ksmbd_conn *conn,
 				  struct smb2_negotiate_rsp *rsp)
 {
-	/* +4 is to account for the RFC1001 len field */
-	char *pneg_ctxt = (char *)rsp +
-			le32_to_cpu(rsp->NegotiateContextOffset) + 4;
+	char * const pneg_ctxt = (char *)rsp +
+			le32_to_cpu(rsp->NegotiateContextOffset);
 	int neg_ctxt_cnt = 1;
 	int ctxt_size;
 
@@ -814,94 +853,90 @@
 		    "assemble SMB2_PREAUTH_INTEGRITY_CAPABILITIES context\n");
 	build_preauth_ctxt((struct smb2_preauth_neg_context *)pneg_ctxt,
 			   conn->preauth_info->Preauth_HashId);
-	rsp->NegotiateContextCount = cpu_to_le16(neg_ctxt_cnt);
-	inc_rfc1001_len(rsp, AUTH_GSS_PADDING);
 	ctxt_size = sizeof(struct smb2_preauth_neg_context);
-	/* Round to 8 byte boundary */
-	pneg_ctxt += round_up(sizeof(struct smb2_preauth_neg_context), 8);
 
 	if (conn->cipher_type) {
+		/* Round to 8 byte boundary */
 		ctxt_size = round_up(ctxt_size, 8);
 		ksmbd_debug(SMB,
 			    "assemble SMB2_ENCRYPTION_CAPABILITIES context\n");
-		build_encrypt_ctxt((struct smb2_encryption_neg_context *)pneg_ctxt,
+		build_encrypt_ctxt((struct smb2_encryption_neg_context *)
+				   (pneg_ctxt + ctxt_size),
 				   conn->cipher_type);
-		rsp->NegotiateContextCount = cpu_to_le16(++neg_ctxt_cnt);
+		neg_ctxt_cnt++;
 		ctxt_size += sizeof(struct smb2_encryption_neg_context) + 2;
-		/* Round to 8 byte boundary */
-		pneg_ctxt +=
-			round_up(sizeof(struct smb2_encryption_neg_context) + 2,
-				 8);
-	}
-
-	if (conn->compress_algorithm) {
-		ctxt_size = round_up(ctxt_size, 8);
-		ksmbd_debug(SMB,
-			    "assemble SMB2_COMPRESSION_CAPABILITIES context\n");
-		/* Temporarily set to SMB3_COMPRESS_NONE */
-		build_compression_ctxt((struct smb2_compression_ctx *)pneg_ctxt,
-				       conn->compress_algorithm);
-		rsp->NegotiateContextCount = cpu_to_le16(++neg_ctxt_cnt);
-		ctxt_size += sizeof(struct smb2_compression_ctx) + 2;
-		/* Round to 8 byte boundary */
-		pneg_ctxt += round_up(sizeof(struct smb2_compression_ctx) + 2,
-				      8);
 	}
+	/* compression context not yet supported */
+	WARN_ON(conn->compress_algorithm != SMB3_COMPRESS_NONE);
 
 	if (conn->posix_ext_supported) {
 		ctxt_size = round_up(ctxt_size, 8);
 		ksmbd_debug(SMB,
 			    "assemble SMB2_POSIX_EXTENSIONS_AVAILABLE context\n");
-		build_posix_ctxt((struct smb2_posix_neg_context *)pneg_ctxt);
-		rsp->NegotiateContextCount = cpu_to_le16(++neg_ctxt_cnt);
+		build_posix_ctxt((struct smb2_posix_neg_context *)
+				 (pneg_ctxt + ctxt_size));
+		neg_ctxt_cnt++;
 		ctxt_size += sizeof(struct smb2_posix_neg_context);
-		/* Round to 8 byte boundary */
-		pneg_ctxt += round_up(sizeof(struct smb2_posix_neg_context), 8);
 	}
 
 	if (conn->signing_negotiated) {
 		ctxt_size = round_up(ctxt_size, 8);
 		ksmbd_debug(SMB,
 			    "assemble SMB2_SIGNING_CAPABILITIES context\n");
-		build_sign_cap_ctxt((struct smb2_signing_capabilities *)pneg_ctxt,
+		build_sign_cap_ctxt((struct smb2_signing_capabilities *)
+				    (pneg_ctxt + ctxt_size),
 				    conn->signing_algorithm);
-		rsp->NegotiateContextCount = cpu_to_le16(++neg_ctxt_cnt);
+		neg_ctxt_cnt++;
 		ctxt_size += sizeof(struct smb2_signing_capabilities) + 2;
 	}
 
-	inc_rfc1001_len(rsp, ctxt_size);
+	rsp->NegotiateContextCount = cpu_to_le16(neg_ctxt_cnt);
+	return ctxt_size + AUTH_GSS_PADDING;
 }
 
 static __le32 decode_preauth_ctxt(struct ksmbd_conn *conn,
-				  struct smb2_preauth_neg_context *pneg_ctxt)
+				  struct smb2_preauth_neg_context *pneg_ctxt,
+				  int ctxt_len)
 {
-	__le32 err = STATUS_NO_PREAUTH_INTEGRITY_HASH_OVERLAP;
+	/*
+	 * sizeof(smb2_preauth_neg_context) assumes SMB311_SALT_SIZE Salt,
+	 * which may not be present. Only check for used HashAlgorithms[1].
+	 */
+	if (ctxt_len <
+	    sizeof(struct smb2_neg_context) + 6)
+		return STATUS_INVALID_PARAMETER;
 
-	if (pneg_ctxt->HashAlgorithms == SMB2_PREAUTH_INTEGRITY_SHA512) {
-		conn->preauth_info->Preauth_HashId =
-			SMB2_PREAUTH_INTEGRITY_SHA512;
-		err = STATUS_SUCCESS;
-	}
+	if (pneg_ctxt->HashAlgorithms != SMB2_PREAUTH_INTEGRITY_SHA512)
+		return STATUS_NO_PREAUTH_INTEGRITY_HASH_OVERLAP;
 
-	return err;
+	conn->preauth_info->Preauth_HashId = SMB2_PREAUTH_INTEGRITY_SHA512;
+	return STATUS_SUCCESS;
 }
 
 static void decode_encrypt_ctxt(struct ksmbd_conn *conn,
 				struct smb2_encryption_neg_context *pneg_ctxt,
-				int len_of_ctxts)
+				int ctxt_len)
 {
-	int cph_cnt = le16_to_cpu(pneg_ctxt->CipherCount);
-	int i, cphs_size = cph_cnt * sizeof(__le16);
+	int cph_cnt;
+	int i, cphs_size;
+
+	if (sizeof(struct smb2_encryption_neg_context) > ctxt_len) {
+		pr_err("Invalid SMB2_ENCRYPTION_CAPABILITIES context size\n");
+		return;
+	}
 
 	conn->cipher_type = 0;
 
+	cph_cnt = le16_to_cpu(pneg_ctxt->CipherCount);
+	cphs_size = cph_cnt * sizeof(__le16);
+
 	if (sizeof(struct smb2_encryption_neg_context) + cphs_size >
-	    len_of_ctxts) {
+	    ctxt_len) {
 		pr_err("Invalid cipher count(%d)\n", cph_cnt);
 		return;
 	}
 
-	if (!(server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION))
+	if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION_OFF)
 		return;
 
 	for (i = 0; i < cph_cnt; i++) {
@@ -917,6 +952,25 @@
 	}
 }
 
+/**
+ * smb3_encryption_negotiated() - checks if server and client agreed on enabling encryption
+ * @conn:	smb connection
+ *
+ * Return:	true if connection should be encrypted, else false
+ */
+bool smb3_encryption_negotiated(struct ksmbd_conn *conn)
+{
+	if (!conn->ops->generate_encryptionkey)
+		return false;
+
+	/*
+	 * SMB 3.0 and 3.0.2 dialects use the SMB2_GLOBAL_CAP_ENCRYPTION flag.
+	 * SMB 3.1.1 uses the cipher_type field.
+	 */
+	return (conn->vals->capabilities & SMB2_GLOBAL_CAP_ENCRYPTION) ||
+	    conn->cipher_type;
+}
+
 static void decode_compress_ctxt(struct ksmbd_conn *conn,
 				 struct smb2_compression_ctx *pneg_ctxt)
 {
@@ -925,15 +979,22 @@
 
 static void decode_sign_cap_ctxt(struct ksmbd_conn *conn,
 				 struct smb2_signing_capabilities *pneg_ctxt,
-				 int len_of_ctxts)
+				 int ctxt_len)
 {
-	int sign_algo_cnt = le16_to_cpu(pneg_ctxt->SigningAlgorithmCount);
-	int i, sign_alos_size = sign_algo_cnt * sizeof(__le16);
+	int sign_algo_cnt;
+	int i, sign_alos_size;
+
+	if (sizeof(struct smb2_signing_capabilities) > ctxt_len) {
+		pr_err("Invalid SMB2_SIGNING_CAPABILITIES context length\n");
+		return;
+	}
 
 	conn->signing_negotiated = false;
+	sign_algo_cnt = le16_to_cpu(pneg_ctxt->SigningAlgorithmCount);
+	sign_alos_size = sign_algo_cnt * sizeof(__le16);
 
 	if (sizeof(struct smb2_signing_capabilities) + sign_alos_size >
-	    len_of_ctxts) {
+	    ctxt_len) {
 		pr_err("Invalid signing algorithm count(%d)\n", sign_algo_cnt);
 		return;
 	}
@@ -952,14 +1013,14 @@
 }
 
 static __le32 deassemble_neg_contexts(struct ksmbd_conn *conn,
-				      struct smb2_negotiate_req *req)
+				      struct smb2_negotiate_req *req,
+				      unsigned int len_of_smb)
 {
 	/* +4 is to account for the RFC1001 len field */
-	struct smb2_neg_context *pctx = (struct smb2_neg_context *)((char *)req + 4);
+	struct smb2_neg_context *pctx = (struct smb2_neg_context *)req;
 	int i = 0, len_of_ctxts;
-	int offset = le32_to_cpu(req->NegotiateContextOffset);
-	int neg_ctxt_cnt = le16_to_cpu(req->NegotiateContextCount);
-	int len_of_smb = be32_to_cpu(req->hdr.smb2_buf_length);
+	unsigned int offset = le32_to_cpu(req->NegotiateContextOffset);
+	unsigned int neg_ctxt_cnt = le16_to_cpu(req->NegotiateContextCount);
 	__le32 status = STATUS_INVALID_PARAMETER;
 
 	ksmbd_debug(SMB, "decoding %d negotiate contexts\n", neg_ctxt_cnt);
@@ -971,18 +1032,16 @@
 	len_of_ctxts = len_of_smb - offset;
 
 	while (i++ < neg_ctxt_cnt) {
-		int clen;
-
-		/* check that offset is not beyond end of SMB */
-		if (len_of_ctxts == 0)
-			break;
+		int clen, ctxt_len;
 
-		if (len_of_ctxts < sizeof(struct smb2_neg_context))
+		if (len_of_ctxts < (int)sizeof(struct smb2_neg_context))
 			break;
 
 		pctx = (struct smb2_neg_context *)((char *)pctx + offset);
 		clen = le16_to_cpu(pctx->DataLength);
-		if (clen + sizeof(struct smb2_neg_context) > len_of_ctxts)
+		ctxt_len = clen + sizeof(struct smb2_neg_context);
+
+		if (ctxt_len > len_of_ctxts)
 			break;
 
 		if (pctx->ContextType == SMB2_PREAUTH_INTEGRITY_CAPABILITIES) {
@@ -992,7 +1051,8 @@
 				break;
 
 			status = decode_preauth_ctxt(conn,
-						     (struct smb2_preauth_neg_context *)pctx);
+						     (struct smb2_preauth_neg_context *)pctx,
+						     ctxt_len);
 			if (status != STATUS_SUCCESS)
 				break;
 		} else if (pctx->ContextType == SMB2_ENCRYPTION_CAPABILITIES) {
@@ -1003,7 +1063,7 @@
 
 			decode_encrypt_ctxt(conn,
 					    (struct smb2_encryption_neg_context *)pctx,
-					    len_of_ctxts);
+					    ctxt_len);
 		} else if (pctx->ContextType == SMB2_COMPRESSION_CAPABILITIES) {
 			ksmbd_debug(SMB,
 				    "deassemble SMB2_COMPRESSION_CAPABILITIES context\n");
@@ -1022,15 +1082,15 @@
 		} else if (pctx->ContextType == SMB2_SIGNING_CAPABILITIES) {
 			ksmbd_debug(SMB,
 				    "deassemble SMB2_SIGNING_CAPABILITIES context\n");
+
 			decode_sign_cap_ctxt(conn,
 					     (struct smb2_signing_capabilities *)pctx,
-					     len_of_ctxts);
+					     ctxt_len);
 		}
 
 		/* offsets must be 8 byte aligned */
-		clen = (clen + 7) & ~0x7;
-		offset = clen + sizeof(struct smb2_neg_context);
-		len_of_ctxts -= clen + sizeof(struct smb2_neg_context);
+		offset = (ctxt_len + 7) & ~0x7;
+		len_of_ctxts -= offset;
 	}
 	return status;
 }
@@ -1044,30 +1104,30 @@
 int smb2_handle_negotiate(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_negotiate_req *req = work->request_buf;
-	struct smb2_negotiate_rsp *rsp = work->response_buf;
+	struct smb2_negotiate_req *req = smb2_get_msg(work->request_buf);
+	struct smb2_negotiate_rsp *rsp = smb2_get_msg(work->response_buf);
 	int rc = 0;
-	unsigned int smb2_buf_len, smb2_neg_size;
+	unsigned int smb2_buf_len, smb2_neg_size, neg_ctxt_len = 0;
 	__le32 status;
 
 	ksmbd_debug(SMB, "Received negotiate request\n");
 	conn->need_neg = false;
-	if (ksmbd_conn_good(work)) {
+	if (ksmbd_conn_good(conn)) {
 		pr_err("conn->tcp_status is already in CifsGood State\n");
 		work->send_no_response = 1;
 		return rc;
 	}
 
-	if (req->DialectCount == 0) {
-		pr_err("malformed packet\n");
+	smb2_buf_len = get_rfc1002_len(work->request_buf);
+	smb2_neg_size = offsetof(struct smb2_negotiate_req, Dialects);
+	if (smb2_neg_size > smb2_buf_len) {
 		rsp->hdr.Status = STATUS_INVALID_PARAMETER;
 		rc = -EINVAL;
 		goto err_out;
 	}
 
-	smb2_buf_len = get_rfc1002_len(work->request_buf);
-	smb2_neg_size = offsetof(struct smb2_negotiate_req, Dialects) - 4;
-	if (smb2_neg_size > smb2_buf_len) {
+	if (req->DialectCount == 0) {
+		pr_err("malformed packet\n");
 		rsp->hdr.Status = STATUS_INVALID_PARAMETER;
 		rc = -EINVAL;
 		goto err_out;
@@ -1115,18 +1175,23 @@
 			goto err_out;
 		}
 
-		status = deassemble_neg_contexts(conn, req);
+		status = deassemble_neg_contexts(conn, req,
+						 get_rfc1002_len(work->request_buf));
 		if (status != STATUS_SUCCESS) {
 			pr_err("deassemble_neg_contexts error(0x%x)\n",
 			       status);
 			rsp->hdr.Status = status;
 			rc = -EINVAL;
+			kfree(conn->preauth_info);
+			conn->preauth_info = NULL;
 			goto err_out;
 		}
 
 		rc = init_smb3_11_server(conn);
 		if (rc < 0) {
 			rsp->hdr.Status = STATUS_INVALID_PARAMETER;
+			kfree(conn->preauth_info);
+			conn->preauth_info = NULL;
 			goto err_out;
 		}
 
@@ -1135,7 +1200,7 @@
 						 conn->preauth_info->Preauth_HashValue);
 		rsp->NegotiateContextOffset =
 				cpu_to_le32(OFFSET_OF_NEG_CONTEXT);
-		assemble_neg_contexts(conn, rsp);
+		neg_ctxt_len = assemble_neg_contexts(conn, rsp);
 		break;
 	case SMB302_PROT_ID:
 		init_smb3_02_server(conn);
@@ -1183,12 +1248,8 @@
 
 	rsp->SecurityBufferOffset = cpu_to_le16(128);
 	rsp->SecurityBufferLength = cpu_to_le16(AUTH_GSS_LENGTH);
-	ksmbd_copy_gss_neg_header(((char *)(&rsp->hdr) +
-				  sizeof(rsp->hdr.smb2_buf_length)) +
-				   le16_to_cpu(rsp->SecurityBufferOffset));
-	inc_rfc1001_len(rsp, sizeof(struct smb2_negotiate_rsp) -
-			sizeof(struct smb2_hdr) - sizeof(rsp->Buffer) +
-			 AUTH_GSS_LENGTH);
+	ksmbd_copy_gss_neg_header((char *)(&rsp->hdr) +
+				  le16_to_cpu(rsp->SecurityBufferOffset));
 	rsp->SecurityMode = SMB2_NEGOTIATE_SIGNING_ENABLED_LE;
 	conn->use_spnego = true;
 
@@ -1203,12 +1264,19 @@
 	}
 
 	conn->srv_sec_mode = le16_to_cpu(rsp->SecurityMode);
-	ksmbd_conn_set_need_negotiate(work);
+	ksmbd_conn_set_need_negotiate(conn);
 
 err_out:
+	if (rc)
+		rsp->hdr.Status = STATUS_INSUFFICIENT_RESOURCES;
+
+	if (!rc)
+		rc = ksmbd_iov_pin_rsp(work, rsp,
+				       sizeof(struct smb2_negotiate_rsp) -
+				        sizeof(rsp->Buffer) +
+					AUTH_GSS_LENGTH + neg_ctxt_len);
 	if (rc < 0)
 		smb2_set_err_rsp(work);
-
 	return rc;
 }
 
@@ -1276,9 +1344,8 @@
 
 static int ntlm_negotiate(struct ksmbd_work *work,
 			  struct negotiate_message *negblob,
-			  size_t negblob_len)
+			  size_t negblob_len, struct smb2_sess_setup_rsp *rsp)
 {
-	struct smb2_sess_setup_rsp *rsp = work->response_buf;
 	struct challenge_message *chgblob;
 	unsigned char *spnego_blob = NULL;
 	u16 spnego_blob_len;
@@ -1286,7 +1353,7 @@
 	int sz, rc;
 
 	ksmbd_debug(SMB, "negotiate phase\n");
-	rc = ksmbd_decode_ntlmssp_neg_blob(negblob, negblob_len, work->sess);
+	rc = ksmbd_decode_ntlmssp_neg_blob(negblob, negblob_len, work->conn);
 	if (rc)
 		return rc;
 
@@ -1296,7 +1363,7 @@
 	memset(chgblob, 0, sizeof(struct challenge_message));
 
 	if (!work->conn->use_spnego) {
-		sz = ksmbd_build_ntlmssp_challenge_blob(chgblob, work->sess);
+		sz = ksmbd_build_ntlmssp_challenge_blob(chgblob, work->conn);
 		if (sz < 0)
 			return -ENOMEM;
 
@@ -1312,7 +1379,7 @@
 		return -ENOMEM;
 
 	chgblob = (struct challenge_message *)neg_blob;
-	sz = ksmbd_build_ntlmssp_challenge_blob(chgblob, work->sess);
+	sz = ksmbd_build_ntlmssp_challenge_blob(chgblob, work->conn);
 	if (sz < 0) {
 		rc = -ENOMEM;
 		goto out;
@@ -1354,9 +1421,12 @@
 	struct authenticate_message *authblob;
 	struct ksmbd_user *user;
 	char *name;
-	unsigned int auth_msg_len, name_off, name_len, secbuf_len;
+	unsigned int name_off, name_len, secbuf_len;
 
-	secbuf_len = le16_to_cpu(req->SecurityBufferLength);
+	if (conn->use_spnego && conn->mechToken)
+		secbuf_len = conn->mechTokenLen;
+	else
+		secbuf_len = le16_to_cpu(req->SecurityBufferLength);
 	if (secbuf_len < sizeof(struct authenticate_message)) {
 		ksmbd_debug(SMB, "blob len %d too small\n", secbuf_len);
 		return NULL;
@@ -1364,9 +1434,8 @@
 	authblob = user_authblob(conn, req);
 	name_off = le32_to_cpu(authblob->UserName.BufferOffset);
 	name_len = le16_to_cpu(authblob->UserName.Length);
-	auth_msg_len = le16_to_cpu(req->SecurityBufferOffset) + secbuf_len;
 
-	if (auth_msg_len < (u64)name_off + name_len)
+	if (secbuf_len < (u64)name_off + name_len)
 		return NULL;
 
 	name = smb_strndup_from_utf16((const char *)authblob + name_off,
@@ -1384,10 +1453,10 @@
 	return user;
 }
 
-static int ntlm_authenticate(struct ksmbd_work *work)
+static int ntlm_authenticate(struct ksmbd_work *work,
+			     struct smb2_sess_setup_req *req,
+			     struct smb2_sess_setup_rsp *rsp)
 {
-	struct smb2_sess_setup_req *req = work->request_buf;
-	struct smb2_sess_setup_rsp *rsp = work->response_buf;
 	struct ksmbd_conn *conn = work->conn;
 	struct ksmbd_session *sess = work->sess;
 	struct channel *chann = NULL;
@@ -1410,7 +1479,6 @@
 		memcpy((char *)&rsp->hdr.ProtocolId + sz, spnego_blob, spnego_blob_len);
 		rsp->SecurityBufferLength = cpu_to_le16(spnego_blob_len);
 		kfree(spnego_blob);
-		inc_rfc1001_len(rsp, spnego_blob_len - 1);
 	}
 
 	user = session_user(conn, req);
@@ -1422,72 +1490,77 @@
 	/* Check for previous session */
 	prev_id = le64_to_cpu(req->PreviousSessionId);
 	if (prev_id && prev_id != sess->id)
-		destroy_previous_session(user, prev_id);
+		destroy_previous_session(conn, user, prev_id);
 
 	if (sess->state == SMB2_SESSION_VALID) {
 		/*
 		 * Reuse session if anonymous try to connect
 		 * on reauthetication.
 		 */
-		if (ksmbd_anonymous_user(user)) {
+		if (conn->binding == false && ksmbd_anonymous_user(user)) {
 			ksmbd_free_user(user);
 			return 0;
 		}
-		ksmbd_free_user(sess->user);
-	}
 
-	sess->user = user;
-	if (user_guest(sess->user)) {
-		if (conn->sign) {
-			ksmbd_debug(SMB, "Guest login not allowed when signing enabled\n");
+		if (!ksmbd_compare_user(sess->user, user)) {
+			ksmbd_free_user(user);
 			return -EPERM;
 		}
+		ksmbd_free_user(user);
+	} else {
+		sess->user = user;
+	}
 
+	if (conn->binding == false && user_guest(sess->user)) {
 		rsp->SessionFlags = SMB2_SESSION_FLAG_IS_GUEST_LE;
 	} else {
 		struct authenticate_message *authblob;
 
 		authblob = user_authblob(conn, req);
-		sz = le16_to_cpu(req->SecurityBufferLength);
-		rc = ksmbd_decode_ntlmssp_auth_blob(authblob, sz, sess);
+		if (conn->use_spnego && conn->mechToken)
+			sz = conn->mechTokenLen;
+		else
+			sz = le16_to_cpu(req->SecurityBufferLength);
+		rc = ksmbd_decode_ntlmssp_auth_blob(authblob, sz, conn, sess);
 		if (rc) {
 			set_user_flag(sess->user, KSMBD_USER_FLAG_BAD_PASSWORD);
 			ksmbd_debug(SMB, "authentication failed\n");
 			return -EPERM;
 		}
+	}
 
-		/*
-		 * If session state is SMB2_SESSION_VALID, We can assume
-		 * that it is reauthentication. And the user/password
-		 * has been verified, so return it here.
-		 */
-		if (sess->state == SMB2_SESSION_VALID) {
-			if (conn->binding)
-				goto binding_session;
-			return 0;
-		}
+	/*
+	 * If session state is SMB2_SESSION_VALID, We can assume
+	 * that it is reauthentication. And the user/password
+	 * has been verified, so return it here.
+	 */
+	if (sess->state == SMB2_SESSION_VALID) {
+		if (conn->binding)
+			goto binding_session;
+		return 0;
+	}
 
-		if ((conn->sign || server_conf.enforced_signing) ||
-		    (req->SecurityMode & SMB2_NEGOTIATE_SIGNING_REQUIRED))
-			sess->sign = true;
-
-		if (conn->vals->capabilities & SMB2_GLOBAL_CAP_ENCRYPTION &&
-		    conn->ops->generate_encryptionkey &&
-		    !(req->Flags & SMB2_SESSION_REQ_FLAG_BINDING)) {
-			rc = conn->ops->generate_encryptionkey(sess);
-			if (rc) {
-				ksmbd_debug(SMB,
-					    "SMB3 encryption key generation failed\n");
-				return -EINVAL;
-			}
-			sess->enc = true;
-			rsp->SessionFlags = SMB2_SESSION_FLAG_ENCRYPT_DATA_LE;
-			/*
-			 * signing is disable if encryption is enable
-			 * on this session
-			 */
-			sess->sign = false;
+	if ((rsp->SessionFlags != SMB2_SESSION_FLAG_IS_GUEST_LE &&
+	     (conn->sign || server_conf.enforced_signing)) ||
+	    (req->SecurityMode & SMB2_NEGOTIATE_SIGNING_REQUIRED))
+		sess->sign = true;
+
+	if (smb3_encryption_negotiated(conn) &&
+			!(req->Flags & SMB2_SESSION_REQ_FLAG_BINDING)) {
+		rc = conn->ops->generate_encryptionkey(conn, sess);
+		if (rc) {
+			ksmbd_debug(SMB,
+					"SMB3 encryption key generation failed\n");
+			return -EINVAL;
 		}
+		sess->enc = true;
+		if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION)
+			rsp->SessionFlags = SMB2_SESSION_FLAG_ENCRYPT_DATA_LE;
+		/*
+		 * signing is disable if encryption is enable
+		 * on this session
+		 */
+		sess->sign = false;
 	}
 
 binding_session:
@@ -1499,8 +1572,7 @@
 				return -ENOMEM;
 
 			chann->conn = conn;
-			INIT_LIST_HEAD(&chann->chann_list);
-			list_add(&chann->chann_list, &sess->ksmbd_chann_list);
+			xa_store(&sess->ksmbd_chann_list, (long)conn, chann, GFP_KERNEL);
 		}
 	}
 
@@ -1520,10 +1592,10 @@
 }
 
 #ifdef CONFIG_SMB_SERVER_KERBEROS5
-static int krb5_authenticate(struct ksmbd_work *work)
+static int krb5_authenticate(struct ksmbd_work *work,
+			     struct smb2_sess_setup_req *req,
+			     struct smb2_sess_setup_rsp *rsp)
 {
-	struct smb2_sess_setup_req *req = work->request_buf;
-	struct smb2_sess_setup_rsp *rsp = work->response_buf;
 	struct ksmbd_conn *conn = work->conn;
 	struct ksmbd_session *sess = work->sess;
 	char *in_blob, *out_blob;
@@ -1538,13 +1610,12 @@
 	out_blob = (char *)&rsp->hdr.ProtocolId +
 		le16_to_cpu(rsp->SecurityBufferOffset);
 	out_len = work->response_sz -
-		offsetof(struct smb2_hdr, smb2_buf_length) -
-		le16_to_cpu(rsp->SecurityBufferOffset);
+		(le16_to_cpu(rsp->SecurityBufferOffset) + 4);
 
 	/* Check previous session */
 	prev_sess_id = le64_to_cpu(req->PreviousSessionId);
 	if (prev_sess_id && prev_sess_id != sess->id)
-		destroy_previous_session(sess->user, prev_sess_id);
+		destroy_previous_session(conn, sess->user, prev_sess_id);
 
 	if (sess->state == SMB2_SESSION_VALID)
 		ksmbd_free_user(sess->user);
@@ -1556,22 +1627,21 @@
 		return -EINVAL;
 	}
 	rsp->SecurityBufferLength = cpu_to_le16(out_len);
-	inc_rfc1001_len(rsp, out_len - 1);
 
 	if ((conn->sign || server_conf.enforced_signing) ||
 	    (req->SecurityMode & SMB2_NEGOTIATE_SIGNING_REQUIRED))
 		sess->sign = true;
 
-	if ((conn->vals->capabilities & SMB2_GLOBAL_CAP_ENCRYPTION) &&
-	    conn->ops->generate_encryptionkey) {
-		retval = conn->ops->generate_encryptionkey(sess);
+	if (smb3_encryption_negotiated(conn)) {
+		retval = conn->ops->generate_encryptionkey(conn, sess);
 		if (retval) {
 			ksmbd_debug(SMB,
 				    "SMB3 encryption key generation failed\n");
 			return -EINVAL;
 		}
 		sess->enc = true;
-		rsp->SessionFlags = SMB2_SESSION_FLAG_ENCRYPT_DATA_LE;
+		if (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB2_ENCRYPTION)
+			rsp->SessionFlags = SMB2_SESSION_FLAG_ENCRYPT_DATA_LE;
 		sess->sign = false;
 	}
 
@@ -1583,8 +1653,7 @@
 				return -ENOMEM;
 
 			chann->conn = conn;
-			INIT_LIST_HEAD(&chann->chann_list);
-			list_add(&chann->chann_list, &sess->ksmbd_chann_list);
+			xa_store(&sess->ksmbd_chann_list, (long)conn, chann, GFP_KERNEL);
 		}
 	}
 
@@ -1603,7 +1672,9 @@
 	return 0;
 }
 #else
-static int krb5_authenticate(struct ksmbd_work *work)
+static int krb5_authenticate(struct ksmbd_work *work,
+			     struct smb2_sess_setup_req *req,
+			     struct smb2_sess_setup_rsp *rsp)
 {
 	return -EOPNOTSUPP;
 }
@@ -1612,8 +1683,8 @@
 int smb2_sess_setup(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_sess_setup_req *req = work->request_buf;
-	struct smb2_sess_setup_rsp *rsp = work->response_buf;
+	struct smb2_sess_setup_req *req;
+	struct smb2_sess_setup_rsp *rsp;
 	struct ksmbd_session *sess;
 	struct negotiate_message *negblob;
 	unsigned int negblob_len, negblob_off;
@@ -1621,12 +1692,14 @@
 
 	ksmbd_debug(SMB, "Received request for session setup\n");
 
+	WORK_BUFFERS(work, req, rsp);
+
 	rsp->StructureSize = cpu_to_le16(9);
 	rsp->SessionFlags = 0;
 	rsp->SecurityBufferOffset = cpu_to_le16(72);
 	rsp->SecurityBufferLength = 0;
-	inc_rfc1001_len(rsp, 9);
 
+	ksmbd_conn_lock(conn);
 	if (!req->hdr.SessionId) {
 		sess = ksmbd_smb2_session_create();
 		if (!sess) {
@@ -1634,7 +1707,11 @@
 			goto out_err;
 		}
 		rsp->hdr.SessionId = cpu_to_le64(sess->id);
-		ksmbd_session_register(conn, sess);
+		rc = ksmbd_session_register(conn, sess);
+		if (rc)
+			goto out_err;
+
+		conn->binding = false;
 	} else if (conn->dialect >= SMB30_PROT_ID &&
 		   (server_conf.flags & KSMBD_GLOBAL_FLAG_SMB3_MULTICHANNEL) &&
 		   req->Flags & SMB2_SESSION_REQ_FLAG_BINDING) {
@@ -1646,7 +1723,7 @@
 			goto out_err;
 		}
 
-		if (conn->dialect != sess->conn->dialect) {
+		if (conn->dialect != sess->dialect) {
 			rc = -EINVAL;
 			goto out_err;
 		}
@@ -1656,7 +1733,7 @@
 			goto out_err;
 		}
 
-		if (strncmp(conn->ClientGUID, sess->conn->ClientGUID,
+		if (strncmp(conn->ClientGUID, sess->ClientGUID,
 			    SMB2_CLIENT_GUID_SIZE)) {
 			rc = -ENOENT;
 			goto out_err;
@@ -1672,11 +1749,23 @@
 			goto out_err;
 		}
 
-		if (ksmbd_session_lookup(conn, sess_id)) {
+		if (ksmbd_conn_need_reconnect(conn)) {
+			rc = -EFAULT;
+			ksmbd_user_session_put(sess);
+			sess = NULL;
+			goto out_err;
+		}
+
+		if (is_ksmbd_session_in_connection(conn, sess_id)) {
 			rc = -EACCES;
 			goto out_err;
 		}
 
+		if (user_guest(sess->user)) {
+			rc = -EOPNOTSUPP;
+			goto out_err;
+		}
+
 		conn->binding = true;
 	} else if ((conn->dialect < SMB30_PROT_ID ||
 		    server_conf.flags & KSMBD_GLOBAL_FLAG_SMB3_MULTICHANNEL) &&
@@ -1691,24 +1780,42 @@
 			rc = -ENOENT;
 			goto out_err;
 		}
+
+		if (sess->state == SMB2_SESSION_EXPIRED) {
+			rc = -EFAULT;
+			goto out_err;
+		}
+
+		if (ksmbd_conn_need_reconnect(conn)) {
+			rc = -EFAULT;
+			sess = NULL;
+			goto out_err;
+		}
+
+		conn->binding = false;
 	}
 	work->sess = sess;
 
-	if (sess->state == SMB2_SESSION_EXPIRED)
-		sess->state = SMB2_SESSION_IN_PROGRESS;
-
 	negblob_off = le16_to_cpu(req->SecurityBufferOffset);
 	negblob_len = le16_to_cpu(req->SecurityBufferLength);
-	if (negblob_off < (offsetof(struct smb2_sess_setup_req, Buffer) - 4) ||
-	    negblob_len < offsetof(struct negotiate_message, NegotiateFlags))
-		return -EINVAL;
+	if (negblob_off < offsetof(struct smb2_sess_setup_req, Buffer)) {
+		rc = -EINVAL;
+		goto out_err;
+	}
 
 	negblob = (struct negotiate_message *)((char *)&req->hdr.ProtocolId +
 			negblob_off);
 
 	if (decode_negotiation_token(conn, negblob, negblob_len) == 0) {
-		if (conn->mechToken)
+		if (conn->mechToken) {
 			negblob = (struct negotiate_message *)conn->mechToken;
+			negblob_len = conn->mechTokenLen;
+		}
+	}
+
+	if (negblob_len < offsetof(struct negotiate_message, NegotiateFlags)) {
+		rc = -EINVAL;
+		goto out_err;
 	}
 
 	if (server_conf.auth_mechs & conn->auth_mechs) {
@@ -1718,36 +1825,34 @@
 
 		if (conn->preferred_auth_mech &
 				(KSMBD_AUTH_KRB5 | KSMBD_AUTH_MSKRB5)) {
-			rc = krb5_authenticate(work);
+			rc = krb5_authenticate(work, req, rsp);
 			if (rc) {
 				rc = -EINVAL;
 				goto out_err;
 			}
 
-			ksmbd_conn_set_good(work);
-			sess->state = SMB2_SESSION_VALID;
+			if (!ksmbd_conn_need_reconnect(conn)) {
+				ksmbd_conn_set_good(conn);
+				sess->state = SMB2_SESSION_VALID;
+			}
 			kfree(sess->Preauth_HashValue);
 			sess->Preauth_HashValue = NULL;
 		} else if (conn->preferred_auth_mech == KSMBD_AUTH_NTLMSSP) {
 			if (negblob->MessageType == NtLmNegotiate) {
-				rc = ntlm_negotiate(work, negblob, negblob_len);
+				rc = ntlm_negotiate(work, negblob, negblob_len, rsp);
 				if (rc)
 					goto out_err;
 				rsp->hdr.Status =
 					STATUS_MORE_PROCESSING_REQUIRED;
-				/*
-				 * Note: here total size -1 is done as an
-				 * adjustment for 0 size blob
-				 */
-				inc_rfc1001_len(rsp, le16_to_cpu(rsp->SecurityBufferLength) - 1);
-
 			} else if (negblob->MessageType == NtLmAuthenticate) {
-				rc = ntlm_authenticate(work);
+				rc = ntlm_authenticate(work, req, rsp);
 				if (rc)
 					goto out_err;
 
-				ksmbd_conn_set_good(work);
-				sess->state = SMB2_SESSION_VALID;
+				if (!ksmbd_conn_need_reconnect(conn)) {
+					ksmbd_conn_set_good(conn);
+					sess->state = SMB2_SESSION_VALID;
+				}
 				if (conn->binding) {
 					struct preauth_session *preauth_sess;
 
@@ -1760,6 +1865,10 @@
 				}
 				kfree(sess->Preauth_HashValue);
 				sess->Preauth_HashValue = NULL;
+			} else {
+				pr_info_ratelimited("Unknown NTLMSSP message type : 0x%x\n",
+						le32_to_cpu(negblob->MessageType));
+				rc = -EINVAL;
 			}
 		} else {
 			/* TODO: need one more negotiation */
@@ -1782,6 +1891,8 @@
 		rsp->hdr.Status = STATUS_NETWORK_SESSION_EXPIRED;
 	else if (rc == -ENOMEM)
 		rsp->hdr.Status = STATUS_INSUFFICIENT_RESOURCES;
+	else if (rc == -EOPNOTSUPP)
+		rsp->hdr.Status = STATUS_NOT_SUPPORTED;
 	else if (rc)
 		rsp->hdr.Status = STATUS_LOGON_FAILURE;
 
@@ -1809,13 +1920,31 @@
 			if (sess->user && sess->user->flags & KSMBD_USER_FLAG_DELAY_SESSION)
 				try_delay = true;
 
-			ksmbd_session_destroy(sess);
+			sess->last_active = jiffies;
+			sess->state = SMB2_SESSION_EXPIRED;
+			ksmbd_user_session_put(sess);
 			work->sess = NULL;
-			if (try_delay)
+			if (try_delay) {
+				ksmbd_conn_set_need_reconnect(conn);
 				ssleep(5);
+				ksmbd_conn_set_need_negotiate(conn);
+			}
 		}
+		smb2_set_err_rsp(work);
+	} else {
+		unsigned int iov_len;
+
+		if (rsp->SecurityBufferLength)
+			iov_len = offsetof(struct smb2_sess_setup_rsp, Buffer) +
+				le16_to_cpu(rsp->SecurityBufferLength);
+		else
+			iov_len = sizeof(struct smb2_sess_setup_rsp);
+		rc = ksmbd_iov_pin_rsp(work, rsp, iov_len);
+		if (rc)
+			rsp->hdr.Status = STATUS_INSUFFICIENT_RESOURCES;
 	}
 
+	ksmbd_conn_unlock(conn);
 	return rc;
 }
 
@@ -1828,15 +1957,17 @@
 int smb2_tree_connect(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_tree_connect_req *req = work->request_buf;
-	struct smb2_tree_connect_rsp *rsp = work->response_buf;
+	struct smb2_tree_connect_req *req;
+	struct smb2_tree_connect_rsp *rsp;
 	struct ksmbd_session *sess = work->sess;
 	char *treename = NULL, *name = NULL;
 	struct ksmbd_tree_conn_status status;
 	struct ksmbd_share_config *share;
 	int rc = -EINVAL;
 
-	treename = smb_strndup_from_utf16(req->Buffer,
+	WORK_BUFFERS(work, req, rsp);
+
+	treename = smb_strndup_from_utf16((char *)req + le16_to_cpu(req->PathOffset),
 					  le16_to_cpu(req->PathLength), true,
 					  conn->local_nls);
 	if (IS_ERR(treename)) {
@@ -1845,7 +1976,7 @@
 		goto out_err1;
 	}
 
-	name = ksmbd_extract_sharename(treename);
+	name = ksmbd_extract_sharename(conn->um, treename);
 	if (IS_ERR(name)) {
 		status.ret = KSMBD_TREE_CONN_STATUS_ERROR;
 		goto out_err1;
@@ -1854,7 +1985,7 @@
 	ksmbd_debug(SMB, "tree connect request for tree %s treename %s\n",
 		    name, treename);
 
-	status = ksmbd_tree_conn_connect(sess, name);
+	status = ksmbd_tree_conn_connect(conn, sess, name);
 	if (status.ret == KSMBD_TREE_CONN_STATUS_OK)
 		rsp->hdr.Id.SyncId.TreeId = cpu_to_le32(status.tree_conn->id);
 	else
@@ -1888,13 +2019,19 @@
 	if (conn->posix_ext_supported)
 		status.tree_conn->posix_extensions = true;
 
-out_err1:
+	write_lock(&sess->tree_conns_lock);
+	status.tree_conn->t_state = TREE_CONNECTED;
+	write_unlock(&sess->tree_conns_lock);
 	rsp->StructureSize = cpu_to_le16(16);
+out_err1:
 	rsp->Capabilities = 0;
 	rsp->Reserved = 0;
 	/* default manual caching */
 	rsp->ShareFlags = SMB2_SHAREFLAG_MANUAL_CACHING;
-	inc_rfc1001_len(rsp, 16);
+
+	rc = ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_tree_connect_rsp));
+	if (rc)
+		status.ret = KSMBD_TREE_CONN_STATUS_NOMEM;
 
 	if (!IS_ERR(treename))
 		kfree(treename);
@@ -1906,8 +2043,10 @@
 		rsp->hdr.Status = STATUS_SUCCESS;
 		rc = 0;
 		break;
+	case -ESTALE:
+	case -ENOENT:
 	case KSMBD_TREE_CONN_STATUS_NO_SHARE:
-		rsp->hdr.Status = STATUS_BAD_NETWORK_PATH;
+		rsp->hdr.Status = STATUS_BAD_NETWORK_NAME;
 		break;
 	case -ENOMEM:
 	case KSMBD_TREE_CONN_STATUS_NOMEM:
@@ -1925,6 +2064,9 @@
 		rsp->hdr.Status = STATUS_ACCESS_DENIED;
 	}
 
+	if (status.ret != KSMBD_TREE_CONN_STATUS_OK)
+		smb2_set_err_rsp(work);
+
 	return rc;
 }
 
@@ -1999,27 +2141,60 @@
  */
 int smb2_tree_disconnect(struct ksmbd_work *work)
 {
-	struct smb2_tree_disconnect_rsp *rsp = work->response_buf;
+	struct smb2_tree_disconnect_rsp *rsp;
+	struct smb2_tree_disconnect_req *req;
 	struct ksmbd_session *sess = work->sess;
 	struct ksmbd_tree_connect *tcon = work->tcon;
+	int err;
 
-	rsp->StructureSize = cpu_to_le16(4);
-	inc_rfc1001_len(rsp, 4);
+	WORK_BUFFERS(work, req, rsp);
 
 	ksmbd_debug(SMB, "request\n");
 
 	if (!tcon) {
-		struct smb2_tree_disconnect_req *req = work->request_buf;
-
 		ksmbd_debug(SMB, "Invalid tid %d\n", req->hdr.Id.SyncId.TreeId);
+
 		rsp->hdr.Status = STATUS_NETWORK_NAME_DELETED;
-		smb2_set_err_rsp(work);
-		return 0;
+		err = -ENOENT;
+		goto err_out;
 	}
 
 	ksmbd_close_tree_conn_fds(work);
-	ksmbd_tree_conn_disconnect(sess, tcon);
+
+	write_lock(&sess->tree_conns_lock);
+	if (tcon->t_state == TREE_DISCONNECTED) {
+		write_unlock(&sess->tree_conns_lock);
+		rsp->hdr.Status = STATUS_NETWORK_NAME_DELETED;
+		err = -ENOENT;
+		goto err_out;
+	}
+
+	WARN_ON_ONCE(atomic_dec_and_test(&tcon->refcount));
+	tcon->t_state = TREE_DISCONNECTED;
+	write_unlock(&sess->tree_conns_lock);
+
+	err = ksmbd_tree_conn_disconnect(sess, tcon);
+	if (err) {
+		rsp->hdr.Status = STATUS_NETWORK_NAME_DELETED;
+		goto err_out;
+	}
+
+	work->tcon = NULL;
+
+	rsp->StructureSize = cpu_to_le16(4);
+	err = ksmbd_iov_pin_rsp(work, rsp,
+				sizeof(struct smb2_tree_disconnect_rsp));
+	if (err) {
+		rsp->hdr.Status = STATUS_INSUFFICIENT_RESOURCES;
+		goto err_out;
+	}
+
 	return 0;
+
+err_out:
+	smb2_set_err_rsp(work);
+	return err;
+
 }
 
 /**
@@ -2031,39 +2206,53 @@
 int smb2_session_logoff(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_logoff_rsp *rsp = work->response_buf;
 	struct ksmbd_session *sess = work->sess;
+	struct smb2_logoff_req *req;
+	struct smb2_logoff_rsp *rsp;
+	u64 sess_id;
+	int err;
 
-	rsp->StructureSize = cpu_to_le16(4);
-	inc_rfc1001_len(rsp, 4);
+	WORK_BUFFERS(work, req, rsp);
 
 	ksmbd_debug(SMB, "request\n");
 
-	/* Got a valid session, set connection state */
-	WARN_ON(sess->conn != conn);
+	ksmbd_conn_lock(conn);
+	if (!ksmbd_conn_good(conn)) {
+		ksmbd_conn_unlock(conn);
+		rsp->hdr.Status = STATUS_NETWORK_NAME_DELETED;
+		smb2_set_err_rsp(work);
+		return -ENOENT;
+	}
+	sess_id = le64_to_cpu(req->hdr.SessionId);
+	ksmbd_all_conn_set_status(sess_id, KSMBD_SESS_NEED_RECONNECT);
+	ksmbd_conn_unlock(conn);
 
-	/* setting CifsExiting here may race with start_tcp_sess */
-	ksmbd_conn_set_need_reconnect(work);
 	ksmbd_close_session_fds(work);
-	ksmbd_conn_wait_idle(conn);
+	ksmbd_conn_wait_idle(conn, sess_id);
 
 	if (ksmbd_tree_conn_session_logoff(sess)) {
-		struct smb2_logoff_req *req = work->request_buf;
-
 		ksmbd_debug(SMB, "Invalid tid %d\n", req->hdr.Id.SyncId.TreeId);
 		rsp->hdr.Status = STATUS_NETWORK_NAME_DELETED;
 		smb2_set_err_rsp(work);
-		return 0;
+		return -ENOENT;
 	}
 
 	ksmbd_destroy_file_table(&sess->file_table);
+	down_write(&conn->session_lock);
 	sess->state = SMB2_SESSION_EXPIRED;
+	up_write(&conn->session_lock);
 
 	ksmbd_free_user(sess->user);
 	sess->user = NULL;
+	ksmbd_all_conn_set_status(sess_id, KSMBD_SESS_NEED_NEGOTIATE);
 
-	/* let start_tcp_sess free connection info now */
-	ksmbd_conn_set_need_negotiate(work);
+	rsp->StructureSize = cpu_to_le16(4);
+	err = ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_logoff_rsp));
+	if (err) {
+		rsp->hdr.Status = STATUS_INSUFFICIENT_RESOURCES;
+		smb2_set_err_rsp(work);
+		return err;
+	}
 	return 0;
 }
 
@@ -2075,12 +2264,14 @@
  */
 static noinline int create_smb2_pipe(struct ksmbd_work *work)
 {
-	struct smb2_create_rsp *rsp = work->response_buf;
-	struct smb2_create_req *req = work->request_buf;
+	struct smb2_create_rsp *rsp;
+	struct smb2_create_req *req;
 	int id;
 	int err;
 	char *name;
 
+	WORK_BUFFERS(work, req, rsp);
+
 	name = smb_strndup_from_utf16(req->Buffer, le16_to_cpu(req->NameLength),
 				      1, work->conn->local_nls);
 	if (IS_ERR(name)) {
@@ -2109,12 +2300,15 @@
 	rsp->EndofFile = cpu_to_le64(0);
 	rsp->FileAttributes = ATTR_NORMAL_LE;
 	rsp->Reserved2 = 0;
-	rsp->VolatileFileId = cpu_to_le64(id);
+	rsp->VolatileFileId = id;
 	rsp->PersistentFileId = 0;
 	rsp->CreateContextsOffset = 0;
 	rsp->CreateContextsLength = 0;
 
-	inc_rfc1001_len(rsp, 88); /* StructureSize - 1*/
+	err = ksmbd_iov_pin_rsp(work, rsp, offsetof(struct smb2_create_rsp, Buffer));
+	if (err)
+		goto out;
+
 	kfree(name);
 	return 0;
 
@@ -2142,11 +2336,12 @@
  * @eabuf:	set info command buffer
  * @buf_len:	set info command buffer length
  * @path:	dentry path for get ea
+ * @get_write:	get write access to a mount
  *
  * Return:	0 on success, otherwise error
  */
 static int smb2_set_ea(struct smb2_ea_info *eabuf, unsigned int buf_len,
-		       struct path *path)
+		       const struct path *path, bool get_write)
 {
 	struct user_namespace *user_ns = mnt_user_ns(path->mnt);
 	char *attr_name = NULL, *value;
@@ -2193,7 +2388,7 @@
 			/* delete the EA only when it exits */
 			if (rc > 0) {
 				rc = ksmbd_vfs_remove_xattr(user_ns,
-							    path->dentry,
+							    path,
 							    attr_name);
 
 				if (rc < 0) {
@@ -2207,9 +2402,9 @@
 			/* if the EA doesn't exist, just do nothing. */
 			rc = 0;
 		} else {
-			rc = ksmbd_vfs_setxattr(user_ns,
-						path->dentry, attr_name, value,
-						le16_to_cpu(eabuf->EaValueLength), 0);
+			rc = ksmbd_vfs_setxattr(user_ns, path, attr_name, value,
+						le16_to_cpu(eabuf->EaValueLength),
+						0, true);
 			if (rc < 0) {
 				ksmbd_debug(SMB,
 					    "ksmbd_vfs_setxattr is failed(%d)\n",
@@ -2224,16 +2419,23 @@
 			break;
 		buf_len -= next;
 		eabuf = (struct smb2_ea_info *)((char *)eabuf + next);
-		if (next < (u32)eabuf->EaNameLength + le16_to_cpu(eabuf->EaValueLength))
+		if (buf_len < sizeof(struct smb2_ea_info)) {
+			rc = -EINVAL;
 			break;
+		}
 
+		if (buf_len < sizeof(struct smb2_ea_info) + eabuf->EaNameLength +
+				le16_to_cpu(eabuf->EaValueLength)) {
+			rc = -EINVAL;
+			break;
+		}
 	} while (next != 0);
 
 	kfree(attr_name);
 	return rc;
 }
 
-static noinline int smb2_set_stream_name_xattr(struct path *path,
+static noinline int smb2_set_stream_name_xattr(const struct path *path,
 					       struct ksmbd_file *fp,
 					       char *stream_name, int s_type)
 {
@@ -2265,14 +2467,13 @@
 		return -EBADF;
 	}
 
-	rc = ksmbd_vfs_setxattr(user_ns, path->dentry,
-				xattr_stream_name, NULL, 0, 0);
+	rc = ksmbd_vfs_setxattr(user_ns, path, xattr_stream_name, NULL, 0, 0, false);
 	if (rc < 0)
 		pr_err("Failed to store XATTR stream name :%d\n", rc);
 	return 0;
 }
 
-static int smb2_remove_smb_xattrs(struct path *path)
+static int smb2_remove_smb_xattrs(const struct path *path)
 {
 	struct user_namespace *user_ns = mnt_user_ns(path->mnt);
 	char *name, *xattr_list = NULL;
@@ -2291,22 +2492,22 @@
 			name += strlen(name) + 1) {
 		ksmbd_debug(SMB, "%s, len %zd\n", name, strlen(name));
 
-		if (strncmp(name, XATTR_USER_PREFIX, XATTR_USER_PREFIX_LEN) &&
-		    strncmp(&name[XATTR_USER_PREFIX_LEN], DOS_ATTRIBUTE_PREFIX,
-			    DOS_ATTRIBUTE_PREFIX_LEN) &&
-		    strncmp(&name[XATTR_USER_PREFIX_LEN], STREAM_PREFIX, STREAM_PREFIX_LEN))
-			continue;
-
-		err = ksmbd_vfs_remove_xattr(user_ns, path->dentry, name);
-		if (err)
-			ksmbd_debug(SMB, "remove xattr failed : %s\n", name);
+		if (!strncmp(name, XATTR_USER_PREFIX, XATTR_USER_PREFIX_LEN) &&
+		    !strncmp(&name[XATTR_USER_PREFIX_LEN], STREAM_PREFIX,
+			     STREAM_PREFIX_LEN)) {
+			err = ksmbd_vfs_remove_xattr(user_ns, path,
+						     name);
+			if (err)
+				ksmbd_debug(SMB, "remove xattr failed : %s\n",
+					    name);
+		}
 	}
 out:
 	kvfree(xattr_list);
 	return err;
 }
 
-static int smb2_create_truncate(struct path *path)
+static int smb2_create_truncate(const struct path *path)
 {
 	int rc = vfs_truncate(path, 0);
 
@@ -2325,7 +2526,7 @@
 	return rc;
 }
 
-static void smb2_new_xattrs(struct ksmbd_tree_connect *tcon, struct path *path,
+static void smb2_new_xattrs(struct ksmbd_tree_connect *tcon, const struct path *path,
 			    struct ksmbd_file *fp)
 {
 	struct xattr_dos_attrib da = {0};
@@ -2341,14 +2542,13 @@
 	da.flags = XATTR_DOSINFO_ATTRIB | XATTR_DOSINFO_CREATE_TIME |
 		XATTR_DOSINFO_ITIME;
 
-	rc = ksmbd_vfs_set_dos_attrib_xattr(mnt_user_ns(path->mnt),
-					    path->dentry, &da);
+	rc = ksmbd_vfs_set_dos_attrib_xattr(mnt_user_ns(path->mnt), path, &da, true);
 	if (rc)
 		ksmbd_debug(SMB, "failed to store file attribute into xattr\n");
 }
 
 static void smb2_update_xattrs(struct ksmbd_tree_connect *tcon,
-			       struct path *path, struct ksmbd_file *fp)
+			       const struct path *path, struct ksmbd_file *fp)
 {
 	struct xattr_dos_attrib da;
 	int rc;
@@ -2369,8 +2569,9 @@
 	}
 }
 
-static int smb2_creat(struct ksmbd_work *work, struct path *path, char *name,
-		      int open_flags, umode_t posix_mode, bool is_dir)
+static int smb2_creat(struct ksmbd_work *work, struct path *parent_path,
+		      struct path *path, char *name, int open_flags,
+		      umode_t posix_mode, bool is_dir)
 {
 	struct ksmbd_tree_connect *tcon = work->tcon;
 	struct ksmbd_share_config *share = tcon->share_conf;
@@ -2397,7 +2598,7 @@
 			return rc;
 	}
 
-	rc = ksmbd_vfs_kern_path(work, name, 0, path, 0);
+	rc = ksmbd_vfs_kern_path_locked(work, name, 0, parent_path, path, 0);
 	if (rc) {
 		pr_err("cannot get linux path (%s), err = %d\n",
 		       name, rc);
@@ -2408,7 +2609,7 @@
 
 static int smb2_create_sd_buffer(struct ksmbd_work *work,
 				 struct smb2_create_req *req,
-				 struct path *path)
+				 const struct path *path)
 {
 	struct create_context *context;
 	struct create_sd_buf_req *sd_buf;
@@ -2417,7 +2618,7 @@
 		return -ENOENT;
 
 	/* Parse SD BUFFER create contexts */
-	context = smb2_find_context_vals(req, SMB2_CREATE_SD_BUFFER);
+	context = smb2_find_context_vals(req, SMB2_CREATE_SD_BUFFER, 4);
 	if (!context)
 		return -ENOENT;
 	else if (IS_ERR(context))
@@ -2431,7 +2632,7 @@
 	    sizeof(struct create_sd_buf_req))
 		return -EINVAL;
 	return set_info_sec(work->conn, work->tcon, path, &sd_buf->ntsd,
-			    le32_to_cpu(sd_buf->ccontext.DataLength), true);
+			    le32_to_cpu(sd_buf->ccontext.DataLength), true, false);
 }
 
 static void ksmbd_acls_fattr(struct smb_fattr *fattr,
@@ -2463,8 +2664,8 @@
 	struct ksmbd_session *sess = work->sess;
 	struct ksmbd_tree_connect *tcon = work->tcon;
 	struct smb2_create_req *req;
-	struct smb2_create_rsp *rsp, *rsp_org;
-	struct path path;
+	struct smb2_create_rsp *rsp;
+	struct path path, parent_path;
 	struct ksmbd_share_config *share = tcon->share_conf;
 	struct ksmbd_file *fp = NULL;
 	struct file *filp = NULL;
@@ -2488,8 +2689,8 @@
 	u64 time;
 	umode_t posix_mode = 0;
 	__le32 daccess, maximal_access = 0;
+	int iov_len = 0;
 
-	rsp_org = work->response_buf;
 	WORK_BUFFERS(work, req, rsp);
 
 	if (req->hdr.NextCommand && !work->next_smb2_rcv_hdr_off &&
@@ -2510,11 +2711,10 @@
 		    *(char *)req->Buffer == '\\') {
 			pr_err("not allow directory name included leading slash\n");
 			rc = -EINVAL;
-			goto err_out1;
+			goto err_out2;
 		}
 
-		name = smb2_get_name(share,
-				     req->Buffer,
+		name = smb2_get_name((char *)req + le16_to_cpu(req->NameOffset),
 				     le16_to_cpu(req->NameLength),
 				     work->conn->local_nls);
 		if (IS_ERR(name)) {
@@ -2522,7 +2722,7 @@
 			if (rc != -ENOMEM)
 				rc = -ENOENT;
 			name = NULL;
-			goto err_out1;
+			goto err_out2;
 		}
 
 		ksmbd_debug(SMB, "converted name = %s\n", name);
@@ -2530,48 +2730,44 @@
 			if (!test_share_config_flag(work->tcon->share_conf,
 						    KSMBD_SHARE_FLAG_STREAMS)) {
 				rc = -EBADF;
-				goto err_out1;
+				goto err_out2;
 			}
 			rc = parse_stream_name(name, &stream_name, &s_type);
 			if (rc < 0)
-				goto err_out1;
+				goto err_out2;
 		}
 
 		rc = ksmbd_validate_filename(name);
 		if (rc < 0)
-			goto err_out1;
+			goto err_out2;
 
 		if (ksmbd_share_veto_filename(share, name)) {
 			rc = -ENOENT;
 			ksmbd_debug(SMB, "Reject open(), vetoed file: %s\n",
 				    name);
-			goto err_out1;
+			goto err_out2;
 		}
 	} else {
 		name = kstrdup("", GFP_KERNEL);
 		if (!name) {
 			rc = -ENOMEM;
-			goto err_out1;
+			goto err_out2;
 		}
 	}
 
-	req_op_level = req->RequestedOplockLevel;
-	if (req_op_level == SMB2_OPLOCK_LEVEL_LEASE)
-		lc = parse_lease_state(req);
-
 	if (le32_to_cpu(req->ImpersonationLevel) > le32_to_cpu(IL_DELEGATE_LE)) {
 		pr_err("Invalid impersonationlevel : 0x%x\n",
 		       le32_to_cpu(req->ImpersonationLevel));
 		rc = -EIO;
 		rsp->hdr.Status = STATUS_BAD_IMPERSONATION_LEVEL;
-		goto err_out1;
+		goto err_out2;
 	}
 
 	if (req->CreateOptions && !(req->CreateOptions & CREATE_OPTIONS_MASK)) {
 		pr_err("Invalid create options : 0x%x\n",
 		       le32_to_cpu(req->CreateOptions));
 		rc = -EINVAL;
-		goto err_out1;
+		goto err_out2;
 	} else {
 		if (req->CreateOptions & FILE_SEQUENTIAL_ONLY_LE &&
 		    req->CreateOptions & FILE_RANDOM_ACCESS_LE)
@@ -2581,13 +2777,13 @@
 		    (FILE_OPEN_BY_FILE_ID_LE | CREATE_TREE_CONNECTION |
 		     FILE_RESERVE_OPFILTER_LE)) {
 			rc = -EOPNOTSUPP;
-			goto err_out1;
+			goto err_out2;
 		}
 
 		if (req->CreateOptions & FILE_DIRECTORY_FILE_LE) {
 			if (req->CreateOptions & FILE_NON_DIRECTORY_FILE_LE) {
 				rc = -EINVAL;
-				goto err_out1;
+				goto err_out2;
 			} else if (req->CreateOptions & FILE_NO_COMPRESSION_LE) {
 				req->CreateOptions = ~(FILE_NO_COMPRESSION_LE);
 			}
@@ -2599,49 +2795,49 @@
 		pr_err("Invalid create disposition : 0x%x\n",
 		       le32_to_cpu(req->CreateDisposition));
 		rc = -EINVAL;
-		goto err_out1;
+		goto err_out2;
 	}
 
 	if (!(req->DesiredAccess & DESIRED_ACCESS_MASK)) {
 		pr_err("Invalid desired access : 0x%x\n",
 		       le32_to_cpu(req->DesiredAccess));
 		rc = -EACCES;
-		goto err_out1;
+		goto err_out2;
 	}
 
 	if (req->FileAttributes && !(req->FileAttributes & ATTR_MASK_LE)) {
 		pr_err("Invalid file attribute : 0x%x\n",
 		       le32_to_cpu(req->FileAttributes));
 		rc = -EINVAL;
-		goto err_out1;
+		goto err_out2;
 	}
 
 	if (req->CreateContextsOffset) {
 		/* Parse non-durable handle create contexts */
-		context = smb2_find_context_vals(req, SMB2_CREATE_EA_BUFFER);
+		context = smb2_find_context_vals(req, SMB2_CREATE_EA_BUFFER, 4);
 		if (IS_ERR(context)) {
 			rc = PTR_ERR(context);
-			goto err_out1;
+			goto err_out2;
 		} else if (context) {
 			ea_buf = (struct create_ea_buf_req *)context;
 			if (le16_to_cpu(context->DataOffset) +
 			    le32_to_cpu(context->DataLength) <
 			    sizeof(struct create_ea_buf_req)) {
 				rc = -EINVAL;
-				goto err_out1;
+				goto err_out2;
 			}
 			if (req->CreateOptions & FILE_NO_EA_KNOWLEDGE_LE) {
 				rsp->hdr.Status = STATUS_ACCESS_DENIED;
 				rc = -EACCES;
-				goto err_out1;
+				goto err_out2;
 			}
 		}
 
 		context = smb2_find_context_vals(req,
-						 SMB2_CREATE_QUERY_MAXIMAL_ACCESS_REQUEST);
+						 SMB2_CREATE_QUERY_MAXIMAL_ACCESS_REQUEST, 4);
 		if (IS_ERR(context)) {
 			rc = PTR_ERR(context);
-			goto err_out1;
+			goto err_out2;
 		} else if (context) {
 			ksmbd_debug(SMB,
 				    "get query maximal access context\n");
@@ -2649,30 +2845,30 @@
 		}
 
 		context = smb2_find_context_vals(req,
-						 SMB2_CREATE_TIMEWARP_REQUEST);
+						 SMB2_CREATE_TIMEWARP_REQUEST, 4);
 		if (IS_ERR(context)) {
 			rc = PTR_ERR(context);
-			goto err_out1;
+			goto err_out2;
 		} else if (context) {
 			ksmbd_debug(SMB, "get timewarp context\n");
 			rc = -EBADF;
-			goto err_out1;
+			goto err_out2;
 		}
 
 		if (tcon->posix_extensions) {
 			context = smb2_find_context_vals(req,
-							 SMB2_CREATE_TAG_POSIX);
+							 SMB2_CREATE_TAG_POSIX, 16);
 			if (IS_ERR(context)) {
 				rc = PTR_ERR(context);
-				goto err_out1;
+				goto err_out2;
 			} else if (context) {
 				struct create_posix *posix =
 					(struct create_posix *)context;
 				if (le16_to_cpu(context->DataOffset) +
 				    le32_to_cpu(context->DataLength) <
-				    sizeof(struct create_posix)) {
+				    sizeof(struct create_posix) - 4) {
 					rc = -EINVAL;
-					goto err_out1;
+					goto err_out2;
 				}
 				ksmbd_debug(SMB, "get posix context\n");
 
@@ -2684,11 +2880,14 @@
 
 	if (ksmbd_override_fsids(work)) {
 		rc = -ENOMEM;
-		goto err_out1;
+		goto err_out2;
 	}
 
-	rc = ksmbd_vfs_kern_path(work, name, LOOKUP_NO_SYMLINKS, &path, 1);
+	rc = ksmbd_vfs_kern_path_locked(work, name, LOOKUP_NO_SYMLINKS,
+					&parent_path, &path, 1);
 	if (!rc) {
+		file_present = true;
+
 		if (req->CreateOptions & FILE_DELETE_ON_CLOSE_LE) {
 			/*
 			 * If file exists with under flags, return access
@@ -2697,7 +2896,6 @@
 			if (req->CreateDisposition == FILE_OVERWRITE_IF_LE ||
 			    req->CreateDisposition == FILE_OPEN_IF_LE) {
 				rc = -EACCES;
-				path_put(&path);
 				goto err_out;
 			}
 
@@ -2705,27 +2903,23 @@
 				ksmbd_debug(SMB,
 					    "User does not have write permission\n");
 				rc = -EACCES;
-				path_put(&path);
 				goto err_out;
 			}
 		} else if (d_is_symlink(path.dentry)) {
 			rc = -EACCES;
-			path_put(&path);
 			goto err_out;
 		}
-	}
 
-	if (rc) {
+		file_present = true;
+		user_ns = mnt_user_ns(path.mnt);
+	} else {
 		if (rc != -ENOENT)
 			goto err_out;
 		ksmbd_debug(SMB, "can not get linux path for %s, rc = %d\n",
 			    name, rc);
 		rc = 0;
-	} else {
-		file_present = true;
-		user_ns = mnt_user_ns(path.mnt);
-		generic_fillattr(user_ns, d_inode(path.dentry), &stat);
 	}
+
 	if (stream_name) {
 		if (req->CreateOptions & FILE_DIRECTORY_FILE_LE) {
 			if (s_type == DATA_STREAM) {
@@ -2733,7 +2927,8 @@
 				rsp->hdr.Status = STATUS_NOT_A_DIRECTORY;
 			}
 		} else {
-			if (S_ISDIR(stat.mode) && s_type == DATA_STREAM) {
+			if (file_present && S_ISDIR(d_inode(path.dentry)->i_mode) &&
+			    s_type == DATA_STREAM) {
 				rc = -EIO;
 				rsp->hdr.Status = STATUS_FILE_IS_A_DIRECTORY;
 			}
@@ -2750,7 +2945,8 @@
 	}
 
 	if (file_present && req->CreateOptions & FILE_NON_DIRECTORY_FILE_LE &&
-	    S_ISDIR(stat.mode) && !(req->CreateOptions & FILE_DELETE_ON_CLOSE_LE)) {
+	    S_ISDIR(d_inode(path.dentry)->i_mode) &&
+	    !(req->CreateOptions & FILE_DELETE_ON_CLOSE_LE)) {
 		ksmbd_debug(SMB, "open() argument is a directory: %s, %x\n",
 			    name, req->CreateOptions);
 		rsp->hdr.Status = STATUS_FILE_IS_A_DIRECTORY;
@@ -2760,7 +2956,7 @@
 
 	if (file_present && (req->CreateOptions & FILE_DIRECTORY_FILE_LE) &&
 	    !(req->CreateDisposition == FILE_CREATE_LE) &&
-	    !S_ISDIR(stat.mode)) {
+	    !S_ISDIR(d_inode(path.dentry)->i_mode)) {
 		rsp->hdr.Status = STATUS_NOT_A_DIRECTORY;
 		rc = -EIO;
 		goto err_out;
@@ -2785,11 +2981,9 @@
 		if (!file_present) {
 			daccess = cpu_to_le32(GENERIC_ALL_FLAGS);
 		} else {
-			rc = ksmbd_vfs_query_maximal_access(user_ns,
+			ksmbd_vfs_query_maximal_access(user_ns,
 							    path.dentry,
 							    &daccess);
-			if (rc)
-				goto err_out;
 			already_permitted = true;
 		}
 		maximal_access = daccess;
@@ -2800,7 +2994,7 @@
 					    &may_flags);
 
 	if (!test_tree_conn_flag(tcon, KSMBD_TREE_CONN_FLAG_WRITABLE)) {
-		if (open_flags & O_CREAT) {
+		if (open_flags & (O_CREAT | O_TRUNC)) {
 			ksmbd_debug(SMB,
 				    "User does not have write permission\n");
 			rc = -EACCES;
@@ -2810,7 +3004,8 @@
 
 	/*create file if not present */
 	if (!file_present) {
-		rc = smb2_creat(work, &path, name, open_flags, posix_mode,
+		rc = smb2_creat(work, &parent_path, &path, name, open_flags,
+				posix_mode,
 				req->CreateOptions & FILE_DIRECTORY_FILE_LE);
 		if (rc) {
 			if (rc == -ENOENT) {
@@ -2831,7 +3026,7 @@
 
 			rc = smb2_set_ea(&ea_buf->ea,
 					 le32_to_cpu(ea_buf->ccontext.DataLength),
-					 &path);
+					 &path, false);
 			if (rc == -EOPNOTSUPP)
 				rc = 0;
 			else if (rc)
@@ -2851,15 +3046,16 @@
 
 			if ((daccess & FILE_DELETE_LE) ||
 			    (req->CreateOptions & FILE_DELETE_ON_CLOSE_LE)) {
-				rc = ksmbd_vfs_may_delete(user_ns,
-							  path.dentry);
+				rc = inode_permission(user_ns,
+						      d_inode(path.dentry->d_parent),
+						      MAY_EXEC | MAY_WRITE);
 				if (rc)
 					goto err_out;
 			}
 		}
 	}
 
-	rc = ksmbd_query_inode_status(d_inode(path.dentry->d_parent));
+	rc = ksmbd_query_inode_status(path.dentry->d_parent);
 	if (rc == KSMBD_INODE_STATUS_PENDING_DELETE) {
 		rc = -EBUSY;
 		goto err_out;
@@ -2904,7 +3100,6 @@
 		goto err_out;
 	}
 
-	fp->filename = name;
 	fp->cdoption = req->CreateDisposition;
 	fp->daccess = daccess;
 	fp->saccess = req->ShareAccess;
@@ -2916,7 +3111,7 @@
 		struct inode *inode = d_inode(path.dentry);
 
 		posix_acl_rc = ksmbd_vfs_inherit_posix_acl(user_ns,
-							   inode,
+							   &path,
 							   d_inode(path.dentry->d_parent));
 		if (posix_acl_rc)
 			ksmbd_debug(SMB, "inherit posix acl failed : %d\n", posix_acl_rc);
@@ -2932,7 +3127,7 @@
 			if (rc) {
 				if (posix_acl_rc)
 					ksmbd_vfs_set_init_posix_acl(user_ns,
-								     inode);
+								     &path);
 
 				if (test_share_config_flag(work->tcon->share_conf,
 							   KSMBD_SHARE_FLAG_ACL_XATTR)) {
@@ -2951,23 +3146,31 @@
 							sizeof(struct smb_acl) +
 							sizeof(struct smb_ace) * ace_num * 2,
 							GFP_KERNEL);
-					if (!pntsd)
+					if (!pntsd) {
+						posix_acl_release(fattr.cf_acls);
+						posix_acl_release(fattr.cf_dacls);
 						goto err_out;
+					}
 
 					rc = build_sec_desc(user_ns,
-							    pntsd, NULL,
+							    pntsd, NULL, 0,
 							    OWNER_SECINFO |
 							    GROUP_SECINFO |
 							    DACL_SECINFO,
 							    &pntsd_size, &fattr);
 					posix_acl_release(fattr.cf_acls);
 					posix_acl_release(fattr.cf_dacls);
+					if (rc) {
+						kfree(pntsd);
+						goto err_out;
+					}
 
 					rc = ksmbd_vfs_set_sd_xattr(conn,
 								    user_ns,
-								    path.dentry,
+								    &path,
 								    pntsd,
-								    pntsd_size);
+								    pntsd_size,
+								    false);
 					kfree(pntsd);
 					if (rc)
 						pr_err("failed to store ntacl in xattr : %d\n",
@@ -2990,11 +3193,6 @@
 
 	fp->attrib_only = !(req->DesiredAccess & ~(FILE_READ_ATTRIBUTES_LE |
 			FILE_WRITE_ATTRIBUTES_LE | FILE_SYNCHRONIZE_LE));
-	if (!S_ISDIR(file_inode(filp)->i_mode) && open_flags & O_TRUNC &&
-	    !fp->attrib_only && !stream_name) {
-		smb_break_all_oplock(work, fp);
-		need_truncate = 1;
-	}
 
 	/* fp should be searchable through ksmbd_inode.m_fp_list
 	 * after daccess, saccess, attrib_only, and stream are
@@ -3004,35 +3202,49 @@
 	list_add(&fp->node, &fp->f_ci->m_fp_list);
 	write_unlock(&fp->f_ci->m_lock);
 
-	rc = ksmbd_vfs_getattr(&path, &stat);
-	if (rc) {
-		generic_fillattr(user_ns, d_inode(path.dentry), &stat);
-		rc = 0;
-	}
-
 	/* Check delete pending among previous fp before oplock break */
 	if (ksmbd_inode_pending_delete(fp)) {
 		rc = -EBUSY;
 		goto err_out;
 	}
 
+	if (file_present || created)
+		ksmbd_vfs_kern_path_unlock(&parent_path, &path);
+
+	if (!S_ISDIR(file_inode(filp)->i_mode) && open_flags & O_TRUNC &&
+	    !fp->attrib_only && !stream_name) {
+		smb_break_all_oplock(work, fp);
+		need_truncate = 1;
+	}
+
+	req_op_level = req->RequestedOplockLevel;
+	if (req_op_level == SMB2_OPLOCK_LEVEL_LEASE)
+		lc = parse_lease_state(req, S_ISDIR(file_inode(filp)->i_mode));
+
 	share_ret = ksmbd_smb_check_shared_mode(fp->filp, fp);
 	if (!test_share_config_flag(work->tcon->share_conf, KSMBD_SHARE_FLAG_OPLOCKS) ||
 	    (req_op_level == SMB2_OPLOCK_LEVEL_LEASE &&
 	     !(conn->vals->capabilities & SMB2_GLOBAL_CAP_LEASING))) {
 		if (share_ret < 0 && !S_ISDIR(file_inode(fp->filp)->i_mode)) {
 			rc = share_ret;
-			goto err_out;
+			goto err_out1;
 		}
 	} else {
 		if (req_op_level == SMB2_OPLOCK_LEVEL_LEASE) {
+			/*
+			 * Compare parent lease using parent key. If there is no
+			 * a lease that has same parent key, Send lease break
+			 * notification.
+			 */
+			smb_send_parent_lease_break_noti(fp, lc);
+
 			req_op_level = smb2_map_lease_to_oplock(lc->req_state);
 			ksmbd_debug(SMB,
 				    "lease req for(%s) req oplock state 0x%x, lease state 0x%x\n",
 				    name, req_op_level, lc->req_state);
 			rc = find_same_lease_key(sess, fp->f_ci, lc);
 			if (rc)
-				goto err_out;
+				goto err_out1;
 		} else if (open_flags == O_RDONLY &&
 			   (req_op_level == SMB2_OPLOCK_LEVEL_BATCH ||
 			    req_op_level == SMB2_OPLOCK_LEVEL_EXCLUSIVE))
@@ -3043,26 +3255,26 @@
 				      le32_to_cpu(req->hdr.Id.SyncId.TreeId),
 				      lc, share_ret);
 		if (rc < 0)
-			goto err_out;
+			goto err_out1;
 	}
 
 	if (req->CreateOptions & FILE_DELETE_ON_CLOSE_LE)
 		ksmbd_fd_set_delete_on_close(fp, file_info);
 
 	if (need_truncate) {
-		rc = smb2_create_truncate(&path);
+		rc = smb2_create_truncate(&fp->filp->f_path);
 		if (rc)
-			goto err_out;
+			goto err_out1;
 	}
 
 	if (req->CreateContextsOffset) {
 		struct create_alloc_size_req *az_req;
 
 		az_req = (struct create_alloc_size_req *)smb2_find_context_vals(req,
-					SMB2_CREATE_ALLOCATION_SIZE);
+					SMB2_CREATE_ALLOCATION_SIZE, 4);
 		if (IS_ERR(az_req)) {
 			rc = PTR_ERR(az_req);
-			goto err_out;
+			goto err_out1;
 		} else if (az_req) {
 			loff_t alloc_size;
 			int err;
@@ -3071,7 +3283,7 @@
 			    le32_to_cpu(az_req->ccontext.DataLength) <
 			    sizeof(struct create_alloc_size_req)) {
 				rc = -EINVAL;
-				goto err_out;
+				goto err_out1;
 			}
 			alloc_size = le64_to_cpu(az_req->AllocationSize);
 			ksmbd_debug(SMB,
@@ -3086,16 +3298,20 @@
 					    err);
 		}
 
-		context = smb2_find_context_vals(req, SMB2_CREATE_QUERY_ON_DISK_ID);
+		context = smb2_find_context_vals(req, SMB2_CREATE_QUERY_ON_DISK_ID, 4);
 		if (IS_ERR(context)) {
 			rc = PTR_ERR(context);
-			goto err_out;
+			goto err_out1;
 		} else if (context) {
 			ksmbd_debug(SMB, "get query on disk id context\n");
 			query_disk_id = 1;
 		}
 	}
 
+	rc = ksmbd_vfs_getattr(&path, &stat);
+	if (rc)
+		goto err_out1;
+
 	if (stat.result_mask & STATX_BTIME)
 		fp->create_time = ksmbd_UnixTimeToNT(stat.btime);
 	else
@@ -3111,9 +3327,6 @@
 
 	memcpy(fp->client_guid, conn->ClientGUID, SMB2_CLIENT_GUID_SIZE);
 
-	generic_fillattr(user_ns, file_inode(fp->filp),
-			 &stat);
-
 	rsp->StructureSize = cpu_to_le16(89);
 	rcu_read_lock();
 	opinfo = rcu_dereference(fp->f_opinfo);
@@ -3135,12 +3348,12 @@
 
 	rsp->Reserved2 = 0;
 
-	rsp->PersistentFileId = cpu_to_le64(fp->persistent_id);
-	rsp->VolatileFileId = cpu_to_le64(fp->volatile_id);
+	rsp->PersistentFileId = fp->persistent_id;
+	rsp->VolatileFileId = fp->volatile_id;
 
 	rsp->CreateContextsOffset = 0;
 	rsp->CreateContextsLength = 0;
-	inc_rfc1001_len(rsp_org, 88); /* StructureSize - 1*/
+	iov_len = offsetof(struct smb2_create_rsp, Buffer);
 
 	/* If lease is request send lease context response */
 	if (opinfo && opinfo->is_lease) {
@@ -3155,7 +3368,7 @@
 		create_lease_buf(rsp->Buffer, opinfo->o_lease);
 		le32_add_cpu(&rsp->CreateContextsLength,
 			     conn->vals->create_lease_size);
-		inc_rfc1001_len(rsp_org, conn->vals->create_lease_size);
+		iov_len += conn->vals->create_lease_size;
 		next_ptr = &lease_ccontext->Next;
 		next_off = conn->vals->create_lease_size;
 	}
@@ -3175,7 +3388,7 @@
 				le32_to_cpu(maximal_access));
 		le32_add_cpu(&rsp->CreateContextsLength,
 			     conn->vals->create_mxac_size);
-		inc_rfc1001_len(rsp_org, conn->vals->create_mxac_size);
+		iov_len += conn->vals->create_mxac_size;
 		if (next_ptr)
 			*next_ptr = cpu_to_le32(next_off);
 		next_ptr = &mxac_ccontext->Next;
@@ -3193,7 +3406,7 @@
 				stat.ino, tcon->id);
 		le32_add_cpu(&rsp->CreateContextsLength,
 			     conn->vals->create_disk_id_size);
-		inc_rfc1001_len(rsp_org, conn->vals->create_disk_id_size);
+		iov_len += conn->vals->create_disk_id_size;
 		if (next_ptr)
 			*next_ptr = cpu_to_le32(next_off);
 		next_ptr = &disk_id_ccontext->Next;
@@ -3207,22 +3420,28 @@
 				fp);
 		le32_add_cpu(&rsp->CreateContextsLength,
 			     conn->vals->create_posix_size);
-		inc_rfc1001_len(rsp_org, conn->vals->create_posix_size);
+		iov_len += conn->vals->create_posix_size;
 		if (next_ptr)
 			*next_ptr = cpu_to_le32(next_off);
 	}
 
 	if (contxt_cnt > 0) {
 		rsp->CreateContextsOffset =
-			cpu_to_le32(offsetof(struct smb2_create_rsp, Buffer)
-			- 4);
+			cpu_to_le32(offsetof(struct smb2_create_rsp, Buffer));
 	}
 
 err_out:
-	if (file_present || created)
-		path_put(&path);
-	ksmbd_revert_fsids(work);
+	if (rc && (file_present || created))
+		ksmbd_vfs_kern_path_unlock(&parent_path, &path);
+
 err_out1:
+	ksmbd_revert_fsids(work);
+
+err_out2:
+	if (!rc) {
+		ksmbd_update_fstate(&work->sess->file_table, fp, FP_INITED);
+		rc = ksmbd_iov_pin_rsp(work, (void *)rsp, iov_len);
+	}
 	if (rc) {
 		if (rc == -EINVAL)
 			rsp->hdr.Status = STATUS_INVALID_PARAMETER;
@@ -3249,14 +3468,13 @@
 		if (!rsp->hdr.Status)
 			rsp->hdr.Status = STATUS_UNEXPECTED_IO_ERROR;
 
-		if (!fp || !fp->filename)
-			kfree(name);
 		if (fp)
 			ksmbd_fd_put(work, fp);
 		smb2_set_err_rsp(work);
 		ksmbd_debug(SMB, "Error response: %x\n", rsp->hdr.Status);
 	}
 
+	kfree(name);
 	kfree(lc);
 
 	return 0;
@@ -3368,7 +3586,6 @@
  * @conn:	connection instance
  * @info_level:	smb information level
  * @d_info:	structure included variables for query dir
- * @user_ns:	user namespace
  * @ksmbd_kstat:	ksmbd wrapper of dirent stat information
  *
  * if directory has many entries, find first can't read it fully.
@@ -3398,9 +3615,9 @@
 		goto free_conv_name;
 	}
 
-	struct_sz = readdir_info_level_struct_sz(info_level);
-	next_entry_offset = ALIGN(struct_sz - 1 + conv_len,
-				  KSMBD_DIR_INFO_ALIGNMENT);
+	struct_sz = readdir_info_level_struct_sz(info_level) + conv_len;
+	next_entry_offset = ALIGN(struct_sz, KSMBD_DIR_INFO_ALIGNMENT);
+	d_info->last_entry_off_align = next_entry_offset - struct_sz;
 
 	if (next_entry_offset > d_info->out_buf_len) {
 		d_info->out_buf_len = 0;
@@ -3525,16 +3742,21 @@
 		posix_info->AllocationSize = cpu_to_le64(ksmbd_kstat->kstat->blocks << 9);
 		posix_info->DeviceId = cpu_to_le32(ksmbd_kstat->kstat->rdev);
 		posix_info->HardLinks = cpu_to_le32(ksmbd_kstat->kstat->nlink);
-		posix_info->Mode = cpu_to_le32(ksmbd_kstat->kstat->mode);
+		posix_info->Mode = cpu_to_le32(ksmbd_kstat->kstat->mode & 0777);
 		posix_info->Inode = cpu_to_le64(ksmbd_kstat->kstat->ino);
 		posix_info->DosAttributes =
 			S_ISDIR(ksmbd_kstat->kstat->mode) ? ATTR_DIRECTORY_LE : ATTR_ARCHIVE_LE;
 		if (d_info->hide_dot_file && d_info->name[0] == '.')
 			posix_info->DosAttributes |= ATTR_HIDDEN_LE;
+		/*
+		 * SidBuffer(32) contain two sids(Domain sid(16), UNIX group sid(16)).
+		 * UNIX sid(16) = revision(1) + num_subauth(1) + authority(6) +
+		 *		  sub_auth(4 * 1(num_subauth)) + RID(4).
+		 */
 		id_to_sid(from_kuid_munged(&init_user_ns, ksmbd_kstat->kstat->uid),
-			  SIDNFS_USER, (struct smb_sid *)&posix_info->SidBuffer[0]);
+			  SIDUNIX_USER, (struct smb_sid *)&posix_info->SidBuffer[0]);
 		id_to_sid(from_kgid_munged(&init_user_ns, ksmbd_kstat->kstat->gid),
-			  SIDNFS_GROUP, (struct smb_sid *)&posix_info->SidBuffer[20]);
+			  SIDUNIX_GROUP, (struct smb_sid *)&posix_info->SidBuffer[16]);
 		memcpy(posix_info->name, conv_name, conv_len);
 		posix_info->name_len = cpu_to_le32(conv_len);
 		posix_info->NextEntryOffset = cpu_to_le32(next_entry_offset);
@@ -3644,7 +3866,7 @@
 		return -EOPNOTSUPP;
 
 	conv_len = (d_info->name_len + 1) * 2;
-	next_entry_offset = ALIGN(struct_sz - 1 + conv_len,
+	next_entry_offset = ALIGN(struct_sz + conv_len,
 				  KSMBD_DIR_INFO_ALIGNMENT);
 
 	if (next_entry_offset > d_info->out_buf_len) {
@@ -3771,11 +3993,6 @@
 	return 0;
 }
 
-static void restart_ctx(struct dir_context *ctx)
-{
-	ctx->pos = 0;
-}
-
 static int verify_info_level(int info_level)
 {
 	switch (info_level) {
@@ -3794,6 +4011,15 @@
 	return 0;
 }
 
+static int smb2_resp_buf_len(struct ksmbd_work *work, unsigned short hdr2_len)
+{
+	int free_len;
+
+	free_len = (int)(work->response_sz -
+		(get_rfc1002_len(work->response_buf) + 4)) - hdr2_len;
+	return free_len;
+}
+
 static int smb2_calc_max_out_buf_len(struct ksmbd_work *work,
 				     unsigned short hdr2_len,
 				     unsigned int out_buf_len)
@@ -3803,9 +4029,7 @@
 	if (out_buf_len > work->conn->vals->max_trans_size)
 		return -EINVAL;
 
-	free_len = (int)(work->response_sz -
-			 (get_rfc1002_len(work->response_buf) + 4)) -
-		hdr2_len;
+	free_len = smb2_resp_buf_len(work, hdr2_len);
 	if (free_len < 0)
 		return -EINVAL;
 
@@ -3816,7 +4040,7 @@
 {
 	struct ksmbd_conn *conn = work->conn;
 	struct smb2_query_directory_req *req;
-	struct smb2_query_directory_rsp *rsp, *rsp_org;
+	struct smb2_query_directory_rsp *rsp;
 	struct ksmbd_share_config *share = work->tcon->share_conf;
 	struct ksmbd_file *dir_fp = NULL;
 	struct ksmbd_dir_info d_info;
@@ -3826,7 +4050,6 @@
 	int buffer_sz;
 	struct smb2_query_dir_private query_dir_private = {NULL, };
 
-	rsp_org = work->response_buf;
 	WORK_BUFFERS(work, req, rsp);
 
 	if (ksmbd_override_fsids(work)) {
@@ -3841,9 +4064,7 @@
 		goto err_out2;
 	}
 
-	dir_fp = ksmbd_lookup_fd_slow(work,
-				      le64_to_cpu(req->VolatileFileId),
-				      le64_to_cpu(req->PersistentFileId));
+	dir_fp = ksmbd_lookup_fd_slow(work, req->VolatileFileId, req->PersistentFileId);
 	if (!dir_fp) {
 		rc = -EBADF;
 		goto err_out2;
@@ -3853,8 +4074,7 @@
 	    inode_permission(file_mnt_user_ns(dir_fp->filp),
 			     file_inode(dir_fp->filp),
 			     MAY_READ | MAY_EXEC)) {
-		pr_err("no right to enumerate directory (%pd)\n",
-		       dir_fp->filp->f_path.dentry);
+		pr_err("no right to enumerate directory (%pD)\n", dir_fp->filp);
 		rc = -EACCES;
 		goto err_out2;
 	}
@@ -3866,7 +4086,7 @@
 	}
 
 	srch_flag = req->Flags;
-	srch_ptr = smb_strndup_from_utf16(req->Buffer,
+	srch_ptr = smb_strndup_from_utf16((char *)req + le16_to_cpu(req->FileNameOffset),
 					  le16_to_cpu(req->FileNameLength), 1,
 					  conn->local_nls);
 	if (IS_ERR(srch_ptr)) {
@@ -3877,12 +4097,9 @@
 		ksmbd_debug(SMB, "Search pattern is %s\n", srch_ptr);
 	}
 
-	ksmbd_debug(SMB, "Directory name is %s\n", dir_fp->filename);
-
 	if (srch_flag & SMB2_REOPEN || srch_flag & SMB2_RESTART_SCANS) {
 		ksmbd_debug(SMB, "Restart directory scan\n");
 		generic_file_llseek(dir_fp->filp, 0, SEEK_SET);
-		restart_ctx(&dir_fp->readdir_data.ctx);
 	}
 
 	memset(&d_info, 0, sizeof(struct ksmbd_dir_info));
@@ -3923,11 +4140,15 @@
 	set_ctx_actor(&dir_fp->readdir_data.ctx, __query_dir);
 
 	rc = iterate_dir(dir_fp->filp, &dir_fp->readdir_data.ctx);
-	if (rc == 0)
-		restart_ctx(&dir_fp->readdir_data.ctx);
-	if (rc == -ENOSPC)
+	/*
+	 * req->OutputBufferLength is too small to contain even one entry.
+	 * In this case, it immediately returns OutputBufferLength 0 to client.
+	 */
+	if (!d_info.out_buf_len && !d_info.num_entry)
+		goto no_buf_len;
+	if (rc > 0 || rc == -ENOSPC)
 		rc = 0;
-	if (rc)
+	else if (rc)
 		goto err_out;
 
 	d_info.wptr = d_info.rptr;
@@ -3947,16 +4168,26 @@
 		rsp->OutputBufferOffset = cpu_to_le16(0);
 		rsp->OutputBufferLength = cpu_to_le32(0);
 		rsp->Buffer[0] = 0;
-		inc_rfc1001_len(rsp_org, 9);
+		rc = ksmbd_iov_pin_rsp(work, (void *)rsp,
+				       sizeof(struct smb2_query_directory_rsp));
+		if (rc)
+			goto err_out;
 	} else {
+no_buf_len:
 		((struct file_directory_info *)
 		((char *)rsp->Buffer + d_info.last_entry_offset))
 		->NextEntryOffset = 0;
+		if (d_info.data_count >= d_info.last_entry_off_align)
+			d_info.data_count -= d_info.last_entry_off_align;
 
 		rsp->StructureSize = cpu_to_le16(9);
 		rsp->OutputBufferOffset = cpu_to_le16(72);
 		rsp->OutputBufferLength = cpu_to_le32(d_info.data_count);
-		inc_rfc1001_len(rsp_org, 8 + d_info.data_count);
+		rc = ksmbd_iov_pin_rsp(work, (void *)rsp,
+				       offsetof(struct smb2_query_directory_rsp, Buffer) +
+				       d_info.data_count);
+		if (rc)
+			goto err_out;
 	}
 
 	kfree(srch_ptr);
@@ -3981,6 +4212,8 @@
 		rsp->hdr.Status = STATUS_NO_MEMORY;
 	else if (rc == -EFAULT)
 		rsp->hdr.Status = STATUS_INVALID_INFO_CLASS;
+	else if (rc == -EIO)
+		rsp->hdr.Status = STATUS_FILE_CORRUPT_ERROR;
 	if (!rsp->hdr.Status)
 		rsp->hdr.Status = STATUS_UNEXPECTED_IO_ERROR;
 
@@ -3994,31 +4227,25 @@
  * buffer_check_err() - helper function to check buffer errors
  * @reqOutputBufferLength:	max buffer length expected in command response
  * @rsp:		query info response buffer contains output buffer length
- * @infoclass_size:	query info class response buffer size
+ * @rsp_org:		base response buffer pointer in case of chained response
  *
  * Return:	0 on success, otherwise error
  */
 static int buffer_check_err(int reqOutputBufferLength,
-			    struct smb2_query_info_rsp *rsp, int infoclass_size)
+			    struct smb2_query_info_rsp *rsp,
+			    void *rsp_org)
 {
 	if (reqOutputBufferLength < le32_to_cpu(rsp->OutputBufferLength)) {
-		if (reqOutputBufferLength < infoclass_size) {
-			pr_err("Invalid Buffer Size Requested\n");
-			rsp->hdr.Status = STATUS_INFO_LENGTH_MISMATCH;
-			rsp->hdr.smb2_buf_length = cpu_to_be32(sizeof(struct smb2_hdr) - 4);
-			return -EINVAL;
-		}
-
-		ksmbd_debug(SMB, "Buffer Overflow\n");
-		rsp->hdr.Status = STATUS_BUFFER_OVERFLOW;
-		rsp->hdr.smb2_buf_length = cpu_to_be32(sizeof(struct smb2_hdr) - 4 +
-				reqOutputBufferLength);
-		rsp->OutputBufferLength = cpu_to_le32(reqOutputBufferLength);
+		pr_err("Invalid Buffer Size Requested\n");
+		rsp->hdr.Status = STATUS_INFO_LENGTH_MISMATCH;
+		*(__be32 *)rsp_org = cpu_to_be32(sizeof(struct smb2_hdr));
+		return -EINVAL;
 	}
 	return 0;
 }
 
-static void get_standard_info_pipe(struct smb2_query_info_rsp *rsp)
+static void get_standard_info_pipe(struct smb2_query_info_rsp *rsp,
+				   void *rsp_org)
 {
 	struct smb2_file_standard_info *sinfo;
 
@@ -4031,10 +4258,10 @@
 	sinfo->Directory = 0;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_standard_info));
-	inc_rfc1001_len(rsp, sizeof(struct smb2_file_standard_info));
 }
 
-static void get_internal_info_pipe(struct smb2_query_info_rsp *rsp, u64 num)
+static void get_internal_info_pipe(struct smb2_query_info_rsp *rsp, u64 num,
+				   void *rsp_org)
 {
 	struct smb2_file_internal_info *file_info;
 
@@ -4044,12 +4271,12 @@
 	file_info->IndexNumber = cpu_to_le64(num | (1ULL << 63));
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_internal_info));
-	inc_rfc1001_len(rsp, sizeof(struct smb2_file_internal_info));
 }
 
 static int smb2_get_info_file_pipe(struct ksmbd_session *sess,
 				   struct smb2_query_info_req *req,
-				   struct smb2_query_info_rsp *rsp)
+				   struct smb2_query_info_rsp *rsp,
+				   void *rsp_org)
 {
 	u64 id;
 	int rc;
@@ -4058,23 +4285,23 @@
 	 * Windows can sometime send query file info request on
 	 * pipe without opening it, checking error condition here
 	 */
-	id = le64_to_cpu(req->VolatileFileId);
+	id = req->VolatileFileId;
 	if (!ksmbd_session_rpc_method(sess, id))
 		return -ENOENT;
 
 	ksmbd_debug(SMB, "FileInfoClass %u, FileId 0x%llx\n",
-		    req->FileInfoClass, le64_to_cpu(req->VolatileFileId));
+		    req->FileInfoClass, req->VolatileFileId);
 
 	switch (req->FileInfoClass) {
 	case FILE_STANDARD_INFORMATION:
-		get_standard_info_pipe(rsp);
+		get_standard_info_pipe(rsp, rsp_org);
 		rc = buffer_check_err(le32_to_cpu(req->OutputBufferLength),
-				      rsp, FILE_STANDARD_INFORMATION_SIZE);
+				      rsp, rsp_org);
 		break;
 	case FILE_INTERNAL_INFORMATION:
-		get_internal_info_pipe(rsp, id);
+		get_internal_info_pipe(rsp, id, rsp_org);
 		rc = buffer_check_err(le32_to_cpu(req->OutputBufferLength),
-				      rsp, FILE_INTERNAL_INFORMATION_SIZE);
+				      rsp, rsp_org);
 		break;
 	default:
 		ksmbd_debug(SMB, "smb2_info_file_pipe for %u not supported\n",
@@ -4103,7 +4330,7 @@
 	int rc, name_len, value_len, xattr_list_len, idx;
 	ssize_t buf_free_len, alignment_bytes, next_offset, rsp_data_cnt = 0;
 	struct smb2_ea_info_req *ea_req = NULL;
-	struct path *path;
+	const struct path *path;
 	struct user_namespace *user_ns = file_mnt_user_ns(fp->filp);
 
 	if (!(fp->daccess & FILE_READ_EA_LE)) {
@@ -4119,7 +4346,8 @@
 		    sizeof(struct smb2_ea_info_req))
 			return -EINVAL;
 
-		ea_req = (struct smb2_ea_info_req *)req->Buffer;
+		ea_req = (struct smb2_ea_info_req *)((char *)req +
+						     le16_to_cpu(req->InputBufferOffset));
 	} else {
 		/* need to send all EAs, if no specific EA is requested*/
 		if (le32_to_cpu(req->Flags) & SL_RETURN_SINGLE_ENTRY)
@@ -4180,7 +4408,7 @@
 		if (!strncmp(name, XATTR_USER_PREFIX, XATTR_USER_PREFIX_LEN))
 			name_len -= XATTR_USER_PREFIX_LEN;
 
-		ptr = (char *)(&eainfo->name + name_len + 1);
+		ptr = eainfo->name + name_len + 1;
 		buf_free_len -= (offsetof(struct smb2_ea_info, name) +
 				name_len + 1);
 		/* bailout if xattr can't fit in buf_free_len */
@@ -4242,7 +4470,6 @@
 	if (rsp_data_cnt == 0)
 		rsp->hdr.Status = STATUS_NO_EAS_ON_FILE;
 	rsp->OutputBufferLength = cpu_to_le32(rsp_data_cnt);
-	inc_rfc1001_len(rsp_org, rsp_data_cnt);
 out:
 	kvfree(xattr_list);
 	return rc;
@@ -4257,7 +4484,6 @@
 	file_info->AccessFlags = fp->daccess;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_access_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_access_info));
 }
 
 static int get_file_basic_info(struct smb2_query_info_rsp *rsp,
@@ -4287,25 +4513,9 @@
 	basic_info->Pad1 = 0;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_basic_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_basic_info));
 	return 0;
 }
 
-static unsigned long long get_allocation_size(struct inode *inode,
-					      struct kstat *stat)
-{
-	unsigned long long alloc_size = 0;
-
-	if (!S_ISDIR(stat->mode)) {
-		if ((inode->i_blocks << 9) <= stat->size)
-			alloc_size = stat->size;
-		else
-			alloc_size = inode->i_blocks << 9;
-	}
-
-	return alloc_size;
-}
-
 static void get_file_standard_info(struct smb2_query_info_rsp *rsp,
 				   struct ksmbd_file *fp, void *rsp_org)
 {
@@ -4320,15 +4530,13 @@
 	sinfo = (struct smb2_file_standard_info *)rsp->Buffer;
 	delete_pending = ksmbd_inode_pending_delete(fp);
 
-	sinfo->AllocationSize = cpu_to_le64(get_allocation_size(inode, &stat));
+	sinfo->AllocationSize = cpu_to_le64(inode->i_blocks << 9);
 	sinfo->EndOfFile = S_ISDIR(stat.mode) ? 0 : cpu_to_le64(stat.size);
 	sinfo->NumberOfLinks = cpu_to_le32(get_nlink(&stat) - delete_pending);
 	sinfo->DeletePending = delete_pending;
 	sinfo->Directory = S_ISDIR(stat.mode) ? 1 : 0;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_standard_info));
-	inc_rfc1001_len(rsp_org,
-			sizeof(struct smb2_file_standard_info));
 }
 
 static void get_file_alignment_info(struct smb2_query_info_rsp *rsp,
@@ -4340,8 +4548,6 @@
 	file_info->AlignmentRequirement = 0;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_alignment_info));
-	inc_rfc1001_len(rsp_org,
-			sizeof(struct smb2_file_alignment_info));
 }
 
 static int get_file_all_info(struct ksmbd_work *work,
@@ -4364,9 +4570,9 @@
 		return -EACCES;
 	}
 
-	filename = convert_to_nt_pathname(fp->filename);
-	if (!filename)
-		return -ENOMEM;
+	filename = convert_to_nt_pathname(work->tcon->share_conf, &fp->filp->f_path);
+	if (IS_ERR(filename))
+		return PTR_ERR(filename);
 
 	inode = file_inode(fp->filp);
 	generic_fillattr(file_mnt_user_ns(fp->filp), inode, &stat);
@@ -4385,7 +4591,7 @@
 	file_info->Attributes = fp->f_ci->m_fattr;
 	file_info->Pad1 = 0;
 	file_info->AllocationSize =
-		cpu_to_le64(get_allocation_size(inode, &stat));
+		cpu_to_le64(inode->i_blocks << 9);
 	file_info->EndOfFile = S_ISDIR(stat.mode) ? 0 : cpu_to_le64(stat.size);
 	file_info->NumberOfLinks =
 			cpu_to_le32(get_nlink(&stat) - delete_pending);
@@ -4405,7 +4611,6 @@
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_all_info) + conv_len - 1);
 	kfree(filename);
-	inc_rfc1001_len(rsp_org, le32_to_cpu(rsp->OutputBufferLength));
 	return 0;
 }
 
@@ -4428,7 +4633,6 @@
 	file_info->FileNameLength = cpu_to_le32(conv_len);
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_alt_name_info) + conv_len);
-	inc_rfc1001_len(rsp_org, le32_to_cpu(rsp->OutputBufferLength));
 }
 
 static void get_file_stream_info(struct ksmbd_work *work,
@@ -4440,7 +4644,7 @@
 	struct smb2_file_stream_info *file_info;
 	char *stream_name, *xattr_list = NULL, *stream_buf;
 	struct kstat stat;
-	struct path *path = &fp->filp->f_path;
+	const struct path *path = &fp->filp->f_path;
 	ssize_t xattr_list_len;
 	int nbytes = 0, streamlen, stream_name_len, next, idx = 0;
 	int buf_free_len;
@@ -4450,6 +4654,12 @@
 			 &stat);
 	file_info = (struct smb2_file_stream_info *)rsp->Buffer;
 
+	buf_free_len =
+		smb2_calc_max_out_buf_len(work, 8,
+					  le32_to_cpu(req->OutputBufferLength));
+	if (buf_free_len < 0)
+		goto out;
+
 	xattr_list_len = ksmbd_vfs_listxattr(path->dentry, &xattr_list);
 	if (xattr_list_len < 0) {
 		goto out;
@@ -4458,12 +4668,6 @@
 		goto out;
 	}
 
-	buf_free_len =
-		smb2_calc_max_out_buf_len(work, 8,
-					  le32_to_cpu(req->OutputBufferLength));
-	if (buf_free_len < 0)
-		goto out;
-
 	while (idx < xattr_list_len) {
 		stream_name = xattr_list + idx;
 		streamlen = strlen(stream_name);
@@ -4489,8 +4693,10 @@
 				     ":%s", &stream_name[XATTR_NAME_STREAM_LEN]);
 
 		next = sizeof(struct smb2_file_stream_info) + streamlen * 2;
-		if (next > buf_free_len)
+		if (next > buf_free_len) {
+			kfree(stream_buf);
 			break;
+		}
 
 		file_info = (struct smb2_file_stream_info *)&rsp->Buffer[nbytes];
 		streamlen  = smbConvertToUTF16((__le16 *)file_info->StreamName,
@@ -4507,6 +4713,7 @@
 		file_info->NextEntryOffset = cpu_to_le32(next);
 	}
 
+out:
 	if (!S_ISDIR(stat.mode) &&
 	    buf_free_len >= sizeof(struct smb2_file_stream_info) + 7 * 2) {
 		file_info = (struct smb2_file_stream_info *)
@@ -4515,18 +4722,16 @@
 					      "::$DATA", 7, conn->local_nls, 0);
 		streamlen *= 2;
 		file_info->StreamNameLength = cpu_to_le32(streamlen);
-		file_info->StreamSize = 0;
-		file_info->StreamAllocationSize = 0;
+		file_info->StreamSize = cpu_to_le64(stat.size);
+		file_info->StreamAllocationSize = cpu_to_le64(stat.blocks << 9);
 		nbytes += sizeof(struct smb2_file_stream_info) + streamlen;
 	}
 
 	/* last entry offset should be 0 */
 	file_info->NextEntryOffset = 0;
-out:
 	kvfree(xattr_list);
 
 	rsp->OutputBufferLength = cpu_to_le32(nbytes);
-	inc_rfc1001_len(rsp_org, nbytes);
 }
 
 static void get_file_internal_info(struct smb2_query_info_rsp *rsp,
@@ -4541,7 +4746,6 @@
 	file_info->IndexNumber = cpu_to_le64(stat.ino);
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_internal_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_internal_info));
 }
 
 static int get_file_network_open_info(struct smb2_query_info_rsp *rsp,
@@ -4572,12 +4776,11 @@
 	file_info->ChangeTime = cpu_to_le64(time);
 	file_info->Attributes = fp->f_ci->m_fattr;
 	file_info->AllocationSize =
-		cpu_to_le64(get_allocation_size(inode, &stat));
+		cpu_to_le64(inode->i_blocks << 9);
 	file_info->EndOfFile = S_ISDIR(stat.mode) ? 0 : cpu_to_le64(stat.size);
 	file_info->Reserved = cpu_to_le32(0);
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_ntwrk_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_ntwrk_info));
 	return 0;
 }
 
@@ -4589,7 +4792,6 @@
 	file_info->EASize = 0;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_ea_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_ea_info));
 }
 
 static void get_file_position_info(struct smb2_query_info_rsp *rsp,
@@ -4601,7 +4803,6 @@
 	file_info->CurrentByteOffset = cpu_to_le64(fp->filp->f_pos);
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_pos_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_pos_info));
 }
 
 static void get_file_mode_info(struct smb2_query_info_rsp *rsp,
@@ -4613,7 +4814,6 @@
 	file_info->Mode = fp->coption & FILE_MODE_INFO_MASK;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_mode_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_mode_info));
 }
 
 static void get_file_compression_info(struct smb2_query_info_rsp *rsp,
@@ -4635,7 +4835,6 @@
 
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_comp_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_comp_info));
 }
 
 static int get_file_attribute_tag_info(struct smb2_query_info_rsp *rsp,
@@ -4654,16 +4853,17 @@
 	file_info->ReparseTag = 0;
 	rsp->OutputBufferLength =
 		cpu_to_le32(sizeof(struct smb2_file_attr_tag_info));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb2_file_attr_tag_info));
 	return 0;
 }
 
-static int find_file_posix_info(struct smb2_query_info_rsp *rsp,
+static void find_file_posix_info(struct smb2_query_info_rsp *rsp,
 				struct ksmbd_file *fp, void *rsp_org)
 {
 	struct smb311_posix_qinfo *file_info;
 	struct inode *inode = file_inode(fp->filp);
+	struct user_namespace *user_ns = file_mnt_user_ns(fp->filp);
 	u64 time;
+	int out_buf_len = sizeof(struct smb311_posix_qinfo) + 32;
 
 	file_info = (struct smb311_posix_qinfo *)rsp->Buffer;
 	file_info->CreationTime = cpu_to_le64(fp->create_time);
@@ -4678,32 +4878,44 @@
 	file_info->EndOfFile = cpu_to_le64(inode->i_size);
 	file_info->AllocationSize = cpu_to_le64(inode->i_blocks << 9);
 	file_info->HardLinks = cpu_to_le32(inode->i_nlink);
-	file_info->Mode = cpu_to_le32(inode->i_mode);
+	file_info->Mode = cpu_to_le32(inode->i_mode & 0777);
 	file_info->DeviceId = cpu_to_le32(inode->i_rdev);
-	rsp->OutputBufferLength =
-		cpu_to_le32(sizeof(struct smb311_posix_qinfo));
-	inc_rfc1001_len(rsp_org, sizeof(struct smb311_posix_qinfo));
-	return 0;
+
+	/*
+	 * Sids(32) contain two sids(Domain sid(16), UNIX group sid(16)).
+	 * UNIX sid(16) = revision(1) + num_subauth(1) + authority(6) +
+	 *		  sub_auth(4 * 1(num_subauth)) + RID(4).
+	 */
+	id_to_sid(from_kuid_munged(&init_user_ns,
+				   i_uid_into_mnt(user_ns, inode)),
+				   SIDUNIX_USER,
+				   (struct smb_sid *)&file_info->Sids[0]);
+	id_to_sid(from_kgid_munged(&init_user_ns,
+				   i_gid_into_mnt(user_ns, inode)),
+				   SIDUNIX_GROUP,
+				   (struct smb_sid *)&file_info->Sids[16]);
+
+	rsp->OutputBufferLength = cpu_to_le32(out_buf_len);
 }
 
 static int smb2_get_info_file(struct ksmbd_work *work,
 			      struct smb2_query_info_req *req,
-			      struct smb2_query_info_rsp *rsp, void *rsp_org)
+			      struct smb2_query_info_rsp *rsp)
 {
 	struct ksmbd_file *fp;
 	int fileinfoclass = 0;
 	int rc = 0;
-	int file_infoclass_size;
 	unsigned int id = KSMBD_NO_FID, pid = KSMBD_NO_FID;
 
 	if (test_share_config_flag(work->tcon->share_conf,
 				   KSMBD_SHARE_FLAG_PIPE)) {
 		/* smb2 info file called for pipe */
-		return smb2_get_info_file_pipe(work->sess, req, rsp);
+		return smb2_get_info_file_pipe(work->sess, req, rsp,
+					       work->response_buf);
 	}
 
 	if (work->next_smb2_rcv_hdr_off) {
-		if (!has_file_id(le64_to_cpu(req->VolatileFileId))) {
+		if (!has_file_id(req->VolatileFileId)) {
 			ksmbd_debug(SMB, "Compound request set FID = %llu\n",
 				    work->compound_fid);
 			id = work->compound_fid;
@@ -4712,8 +4924,8 @@
 	}
 
 	if (!has_file_id(id)) {
-		id = le64_to_cpu(req->VolatileFileId);
-		pid = le64_to_cpu(req->PersistentFileId);
+		id = req->VolatileFileId;
+		pid = req->PersistentFileId;
 	}
 
 	fp = ksmbd_lookup_fd_slow(work, id, pid);
@@ -4724,86 +4936,70 @@
 
 	switch (fileinfoclass) {
 	case FILE_ACCESS_INFORMATION:
-		get_file_access_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_ACCESS_INFORMATION_SIZE;
+		get_file_access_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_BASIC_INFORMATION:
-		rc = get_file_basic_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_BASIC_INFORMATION_SIZE;
+		rc = get_file_basic_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_STANDARD_INFORMATION:
-		get_file_standard_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_STANDARD_INFORMATION_SIZE;
+		get_file_standard_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_ALIGNMENT_INFORMATION:
-		get_file_alignment_info(rsp, rsp_org);
-		file_infoclass_size = FILE_ALIGNMENT_INFORMATION_SIZE;
+		get_file_alignment_info(rsp, work->response_buf);
 		break;
 
 	case FILE_ALL_INFORMATION:
-		rc = get_file_all_info(work, rsp, fp, rsp_org);
-		file_infoclass_size = FILE_ALL_INFORMATION_SIZE;
+		rc = get_file_all_info(work, rsp, fp, work->response_buf);
 		break;
 
 	case FILE_ALTERNATE_NAME_INFORMATION:
-		get_file_alternate_info(work, rsp, fp, rsp_org);
-		file_infoclass_size = FILE_ALTERNATE_NAME_INFORMATION_SIZE;
+		get_file_alternate_info(work, rsp, fp, work->response_buf);
 		break;
 
 	case FILE_STREAM_INFORMATION:
-		get_file_stream_info(work, rsp, fp, rsp_org);
-		file_infoclass_size = FILE_STREAM_INFORMATION_SIZE;
+		get_file_stream_info(work, rsp, fp, work->response_buf);
 		break;
 
 	case FILE_INTERNAL_INFORMATION:
-		get_file_internal_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_INTERNAL_INFORMATION_SIZE;
+		get_file_internal_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_NETWORK_OPEN_INFORMATION:
-		rc = get_file_network_open_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_NETWORK_OPEN_INFORMATION_SIZE;
+		rc = get_file_network_open_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_EA_INFORMATION:
-		get_file_ea_info(rsp, rsp_org);
-		file_infoclass_size = FILE_EA_INFORMATION_SIZE;
+		get_file_ea_info(rsp, work->response_buf);
 		break;
 
 	case FILE_FULL_EA_INFORMATION:
-		rc = smb2_get_ea(work, fp, req, rsp, rsp_org);
-		file_infoclass_size = FILE_FULL_EA_INFORMATION_SIZE;
+		rc = smb2_get_ea(work, fp, req, rsp, work->response_buf);
 		break;
 
 	case FILE_POSITION_INFORMATION:
-		get_file_position_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_POSITION_INFORMATION_SIZE;
+		get_file_position_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_MODE_INFORMATION:
-		get_file_mode_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_MODE_INFORMATION_SIZE;
+		get_file_mode_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_COMPRESSION_INFORMATION:
-		get_file_compression_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_COMPRESSION_INFORMATION_SIZE;
+		get_file_compression_info(rsp, fp, work->response_buf);
 		break;
 
 	case FILE_ATTRIBUTE_TAG_INFORMATION:
-		rc = get_file_attribute_tag_info(rsp, fp, rsp_org);
-		file_infoclass_size = FILE_ATTRIBUTE_TAG_INFORMATION_SIZE;
+		rc = get_file_attribute_tag_info(rsp, fp, work->response_buf);
 		break;
 	case SMB_FIND_FILE_POSIX_INFO:
 		if (!work->tcon->posix_extensions) {
 			pr_err("client doesn't negotiate with SMB3.1.1 POSIX Extensions\n");
 			rc = -EOPNOTSUPP;
 		} else {
-			rc = find_file_posix_info(rsp, fp, rsp_org);
-			file_infoclass_size = sizeof(struct smb311_posix_qinfo);
+			find_file_posix_info(rsp, fp, work->response_buf);
 		}
 		break;
 	default:
@@ -4813,24 +5009,25 @@
 	}
 	if (!rc)
 		rc = buffer_check_err(le32_to_cpu(req->OutputBufferLength),
-				      rsp,
-				      file_infoclass_size);
+				      rsp, work->response_buf);
 	ksmbd_fd_put(work, fp);
 	return rc;
 }
 
 static int smb2_get_info_filesystem(struct ksmbd_work *work,
 				    struct smb2_query_info_req *req,
-				    struct smb2_query_info_rsp *rsp, void *rsp_org)
+				    struct smb2_query_info_rsp *rsp)
 {
 	struct ksmbd_session *sess = work->sess;
-	struct ksmbd_conn *conn = sess->conn;
+	struct ksmbd_conn *conn = work->conn;
 	struct ksmbd_share_config *share = work->tcon->share_conf;
 	int fsinfoclass = 0;
 	struct kstatfs stfs;
 	struct path path;
 	int rc = 0, len;
-	int fs_infoclass_size = 0;
+
+	if (!share->path)
+		return -EIO;
 
 	rc = kern_path(share->path, LOOKUP_NO_SYMLINKS, &path);
 	if (rc) {
@@ -4857,8 +5054,6 @@
 		info->DeviceType = cpu_to_le32(stfs.f_type);
 		info->DeviceCharacteristics = cpu_to_le32(0x00000020);
 		rsp->OutputBufferLength = cpu_to_le32(8);
-		inc_rfc1001_len(rsp_org, 8);
-		fs_infoclass_size = FS_DEVICE_INFORMATION_SIZE;
 		break;
 	}
 	case FS_ATTRIBUTE_INFORMATION:
@@ -4876,6 +5071,10 @@
 
 		info->Attributes |= cpu_to_le32(server_conf.share_fake_fscaps);
 
+		if (test_share_config_flag(work->tcon->share_conf,
+		    KSMBD_SHARE_FLAG_STREAMS))
+			info->Attributes |= cpu_to_le32(FILE_NAMED_STREAMS);
+
 		info->MaxPathNameComponentLength = cpu_to_le32(stfs.f_namelen);
 		len = smbConvertToUTF16((__le16 *)info->FileSystemName,
 					"NTFS", PATH_MAX, conn->local_nls, 0);
@@ -4883,19 +5082,24 @@
 		info->FileSystemNameLen = cpu_to_le32(len);
 		sz = sizeof(struct filesystem_attribute_info) - 2 + len;
 		rsp->OutputBufferLength = cpu_to_le32(sz);
-		inc_rfc1001_len(rsp_org, sz);
-		fs_infoclass_size = FS_ATTRIBUTE_INFORMATION_SIZE;
 		break;
 	}
 	case FS_VOLUME_INFORMATION:
 	{
 		struct filesystem_vol_info *info;
 		size_t sz;
+		unsigned int serial_crc = 0;
 
 		info = (struct filesystem_vol_info *)(rsp->Buffer);
 		info->VolumeCreationTime = 0;
+		serial_crc = crc32_le(serial_crc, share->name,
+				      strlen(share->name));
+		serial_crc = crc32_le(serial_crc, share->path,
+				      strlen(share->path));
+		serial_crc = crc32_le(serial_crc, ksmbd_netbios_name(),
+				      strlen(ksmbd_netbios_name()));
 		/* Taking dummy value of serial number*/
-		info->SerialNumber = cpu_to_le32(0xbc3ac512);
+		info->SerialNumber = cpu_to_le32(serial_crc);
 		len = smbConvertToUTF16((__le16 *)info->VolumeLabel,
 					share->name, PATH_MAX,
 					conn->local_nls, 0);
@@ -4904,8 +5108,6 @@
 		info->Reserved = 0;
 		sz = sizeof(struct filesystem_vol_info) - 2 + len;
 		rsp->OutputBufferLength = cpu_to_le32(sz);
-		inc_rfc1001_len(rsp_org, sz);
-		fs_infoclass_size = FS_VOLUME_INFORMATION_SIZE;
 		break;
 	}
 	case FS_SIZE_INFORMATION:
@@ -4918,8 +5120,6 @@
 		info->SectorsPerAllocationUnit = cpu_to_le32(1);
 		info->BytesPerSector = cpu_to_le32(stfs.f_bsize);
 		rsp->OutputBufferLength = cpu_to_le32(24);
-		inc_rfc1001_len(rsp_org, 24);
-		fs_infoclass_size = FS_SIZE_INFORMATION_SIZE;
 		break;
 	}
 	case FS_FULL_SIZE_INFORMATION:
@@ -4935,8 +5135,6 @@
 		info->SectorsPerAllocationUnit = cpu_to_le32(1);
 		info->BytesPerSector = cpu_to_le32(stfs.f_bsize);
 		rsp->OutputBufferLength = cpu_to_le32(32);
-		inc_rfc1001_len(rsp_org, 32);
-		fs_infoclass_size = FS_FULL_SIZE_INFORMATION_SIZE;
 		break;
 	}
 	case FS_OBJECT_ID_INFORMATION:
@@ -4956,29 +5154,27 @@
 		info->extended_info.rel_date = 0;
 		memcpy(info->extended_info.version_string, "1.1.0", strlen("1.1.0"));
 		rsp->OutputBufferLength = cpu_to_le32(64);
-		inc_rfc1001_len(rsp_org, 64);
-		fs_infoclass_size = FS_OBJECT_ID_INFORMATION_SIZE;
 		break;
 	}
 	case FS_SECTOR_SIZE_INFORMATION:
 	{
 		struct smb3_fs_ss_info *info;
+		unsigned int sector_size =
+			min_t(unsigned int, path.mnt->mnt_sb->s_blocksize, 4096);
 
 		info = (struct smb3_fs_ss_info *)(rsp->Buffer);
 
-		info->LogicalBytesPerSector = cpu_to_le32(stfs.f_bsize);
+		info->LogicalBytesPerSector = cpu_to_le32(sector_size);
 		info->PhysicalBytesPerSectorForAtomicity =
-				cpu_to_le32(stfs.f_bsize);
-		info->PhysicalBytesPerSectorForPerf = cpu_to_le32(stfs.f_bsize);
+				cpu_to_le32(sector_size);
+		info->PhysicalBytesPerSectorForPerf = cpu_to_le32(sector_size);
 		info->FSEffPhysicalBytesPerSectorForAtomicity =
-				cpu_to_le32(stfs.f_bsize);
+				cpu_to_le32(sector_size);
 		info->Flags = cpu_to_le32(SSINFO_FLAGS_ALIGNED_DEVICE |
 				    SSINFO_FLAGS_PARTITION_ALIGNED_ON_DEVICE);
 		info->ByteOffsetForSectorAlignment = 0;
 		info->ByteOffsetForPartitionAlignment = 0;
 		rsp->OutputBufferLength = cpu_to_le32(28);
-		inc_rfc1001_len(rsp_org, 28);
-		fs_infoclass_size = FS_SECTOR_SIZE_INFORMATION_SIZE;
 		break;
 	}
 	case FS_CONTROL_INFORMATION:
@@ -4999,8 +5195,6 @@
 		info->DefaultQuotaLimit = cpu_to_le64(SMB2_NO_FID);
 		info->Padding = 0;
 		rsp->OutputBufferLength = cpu_to_le32(48);
-		inc_rfc1001_len(rsp_org, 48);
-		fs_infoclass_size = FS_CONTROL_INFORMATION_SIZE;
 		break;
 	}
 	case FS_POSIX_INFORMATION:
@@ -5020,8 +5214,6 @@
 			info->TotalFileNodes = cpu_to_le64(stfs.f_files);
 			info->FreeFileNodes = cpu_to_le64(stfs.f_ffree);
 			rsp->OutputBufferLength = cpu_to_le32(56);
-			inc_rfc1001_len(rsp_org, 56);
-			fs_infoclass_size = FS_POSIX_INFORMATION_SIZE;
 		}
 		break;
 	}
@@ -5030,30 +5222,29 @@
 		return -EOPNOTSUPP;
 	}
 	rc = buffer_check_err(le32_to_cpu(req->OutputBufferLength),
-			      rsp,
-			      fs_infoclass_size);
+			      rsp, work->response_buf);
 	path_put(&path);
 	return rc;
 }
 
 static int smb2_get_info_sec(struct ksmbd_work *work,
 			     struct smb2_query_info_req *req,
-			     struct smb2_query_info_rsp *rsp, void *rsp_org)
+			     struct smb2_query_info_rsp *rsp)
 {
 	struct ksmbd_file *fp;
 	struct user_namespace *user_ns;
 	struct smb_ntsd *pntsd = (struct smb_ntsd *)rsp->Buffer, *ppntsd = NULL;
 	struct smb_fattr fattr = {{0}};
 	struct inode *inode;
-	__u32 secdesclen;
+	__u32 secdesclen = 0;
 	unsigned int id = KSMBD_NO_FID, pid = KSMBD_NO_FID;
 	int addition_info = le32_to_cpu(req->AdditionalInformation);
-	int rc;
+	int rc = 0, ppntsd_size = 0;
 
 	if (addition_info & ~(OWNER_SECINFO | GROUP_SECINFO | DACL_SECINFO |
 			      PROTECTED_DACL_SECINFO |
 			      UNPROTECTED_DACL_SECINFO)) {
-		pr_err("Unsupported addition info: 0x%x)\n",
+		ksmbd_debug(SMB, "Unsupported addition info: 0x%x)\n",
 		       addition_info);
 
 		pntsd->revision = cpu_to_le16(1);
@@ -5065,13 +5256,12 @@
 
 		secdesclen = sizeof(struct smb_ntsd);
 		rsp->OutputBufferLength = cpu_to_le32(secdesclen);
-		inc_rfc1001_len(rsp_org, secdesclen);
 
 		return 0;
 	}
 
 	if (work->next_smb2_rcv_hdr_off) {
-		if (!has_file_id(le64_to_cpu(req->VolatileFileId))) {
+		if (!has_file_id(req->VolatileFileId)) {
 			ksmbd_debug(SMB, "Compound request set FID = %llu\n",
 				    work->compound_fid);
 			id = work->compound_fid;
@@ -5080,8 +5270,8 @@
 	}
 
 	if (!has_file_id(id)) {
-		id = le64_to_cpu(req->VolatileFileId);
-		pid = le64_to_cpu(req->PersistentFileId);
+		id = req->VolatileFileId;
+		pid = req->PersistentFileId;
 	}
 
 	fp = ksmbd_lookup_fd_slow(work, id, pid);
@@ -5094,11 +5284,14 @@
 
 	if (test_share_config_flag(work->tcon->share_conf,
 				   KSMBD_SHARE_FLAG_ACL_XATTR))
-		ksmbd_vfs_get_sd_xattr(work->conn, user_ns,
-				       fp->filp->f_path.dentry, &ppntsd);
-
-	rc = build_sec_desc(user_ns, pntsd, ppntsd, addition_info,
-			    &secdesclen, &fattr);
+		ppntsd_size = ksmbd_vfs_get_sd_xattr(work->conn, user_ns,
+						     fp->filp->f_path.dentry,
+						     &ppntsd);
+
+	/* Check if sd buffer size exceeds response buffer size */
+	if (smb2_resp_buf_len(work, 8) > ppntsd_size)
+		rc = build_sec_desc(user_ns, pntsd, ppntsd, ppntsd_size,
+				    addition_info, &secdesclen, &fattr);
 	posix_acl_release(fattr.cf_acls);
 	posix_acl_release(fattr.cf_dacls);
 	kfree(ppntsd);
@@ -5107,7 +5300,6 @@
 		return rc;
 
 	rsp->OutputBufferLength = cpu_to_le32(secdesclen);
-	inc_rfc1001_len(rsp_org, secdesclen);
 	return 0;
 }
 
@@ -5120,10 +5312,9 @@
 int smb2_query_info(struct ksmbd_work *work)
 {
 	struct smb2_query_info_req *req;
-	struct smb2_query_info_rsp *rsp, *rsp_org;
+	struct smb2_query_info_rsp *rsp;
 	int rc = 0;
 
-	rsp_org = work->response_buf;
 	WORK_BUFFERS(work, req, rsp);
 
 	ksmbd_debug(SMB, "GOT query info request\n");
@@ -5131,15 +5322,15 @@
 	switch (req->InfoType) {
 	case SMB2_O_INFO_FILE:
 		ksmbd_debug(SMB, "GOT SMB2_O_INFO_FILE\n");
-		rc = smb2_get_info_file(work, req, rsp, (void *)rsp_org);
+		rc = smb2_get_info_file(work, req, rsp);
 		break;
 	case SMB2_O_INFO_FILESYSTEM:
 		ksmbd_debug(SMB, "GOT SMB2_O_INFO_FILESYSTEM\n");
-		rc = smb2_get_info_filesystem(work, req, rsp, (void *)rsp_org);
+		rc = smb2_get_info_filesystem(work, req, rsp);
 		break;
 	case SMB2_O_INFO_SECURITY:
 		ksmbd_debug(SMB, "GOT SMB2_O_INFO_SECURITY\n");
-		rc = smb2_get_info_sec(work, req, rsp, (void *)rsp_org);
+		rc = smb2_get_info_sec(work, req, rsp);
 		break;
 	default:
 		ksmbd_debug(SMB, "InfoType %d not supported yet\n",
@@ -5147,6 +5338,14 @@
 		rc = -EOPNOTSUPP;
 	}
 
+	if (!rc) {
+		rsp->StructureSize = cpu_to_le16(9);
+		rsp->OutputBufferOffset = cpu_to_le16(72);
+		rc = ksmbd_iov_pin_rsp(work, (void *)rsp,
+				       offsetof(struct smb2_query_info_rsp, Buffer) +
+					le32_to_cpu(rsp->OutputBufferLength));
+	}
+
 	if (rc < 0) {
 		if (rc == -EACCES)
 			rsp->hdr.Status = STATUS_ACCESS_DENIED;
@@ -5154,6 +5353,8 @@
 			rsp->hdr.Status = STATUS_FILE_CLOSED;
 		else if (rc == -EIO)
 			rsp->hdr.Status = STATUS_UNEXPECTED_IO_ERROR;
+		else if (rc == -ENOMEM)
+			rsp->hdr.Status = STATUS_INSUFFICIENT_RESOURCES;
 		else if (rc == -EOPNOTSUPP || rsp->hdr.Status == 0)
 			rsp->hdr.Status = STATUS_INVALID_INFO_CLASS;
 		smb2_set_err_rsp(work);
@@ -5162,9 +5363,6 @@
 			    rc);
 		return rc;
 	}
-	rsp->StructureSize = cpu_to_le16(9);
-	rsp->OutputBufferOffset = cpu_to_le16(72);
-	inc_rfc1001_len(rsp_org, 8);
 	return 0;
 }
 
@@ -5177,10 +5375,12 @@
 static noinline int smb2_close_pipe(struct ksmbd_work *work)
 {
 	u64 id;
-	struct smb2_close_req *req = work->request_buf;
-	struct smb2_close_rsp *rsp = work->response_buf;
+	struct smb2_close_req *req;
+	struct smb2_close_rsp *rsp;
 
-	id = le64_to_cpu(req->VolatileFileId);
+	WORK_BUFFERS(work, req, rsp);
+
+	id = req->VolatileFileId;
 	ksmbd_session_rpc_close(work->sess, id);
 
 	rsp->StructureSize = cpu_to_le16(60);
@@ -5193,8 +5393,9 @@
 	rsp->AllocationSize = 0;
 	rsp->EndOfFile = 0;
 	rsp->Attributes = 0;
-	inc_rfc1001_len(rsp, 60);
-	return 0;
+
+	return ksmbd_iov_pin_rsp(work, (void *)rsp,
+				 sizeof(struct smb2_close_rsp));
 }
 
 /**
@@ -5209,14 +5410,12 @@
 	u64 sess_id;
 	struct smb2_close_req *req;
 	struct smb2_close_rsp *rsp;
-	struct smb2_close_rsp *rsp_org;
 	struct ksmbd_conn *conn = work->conn;
 	struct ksmbd_file *fp;
 	struct inode *inode;
 	u64 time;
 	int err = 0;
 
-	rsp_org = work->response_buf;
 	WORK_BUFFERS(work, req, rsp);
 
 	if (test_share_config_flag(work->tcon->share_conf,
@@ -5241,7 +5440,7 @@
 	}
 
 	if (work->next_smb2_rcv_hdr_off &&
-	    !has_file_id(le64_to_cpu(req->VolatileFileId))) {
+	    !has_file_id(req->VolatileFileId)) {
 		if (!has_file_id(work->compound_fid)) {
 			/* file already closed, return FILE_CLOSED */
 			ksmbd_debug(SMB, "file already closed\n");
@@ -5260,7 +5459,7 @@
 			work->compound_pfid = KSMBD_NO_FID;
 		}
 	} else {
-		volatile_id = le64_to_cpu(req->VolatileFileId);
+		volatile_id = req->VolatileFileId;
 	}
 	ksmbd_debug(SMB, "volatile_id = %llu\n", volatile_id);
 
@@ -5301,15 +5500,17 @@
 
 	err = ksmbd_close_fd(work, volatile_id);
 out:
+	if (!err)
+		err = ksmbd_iov_pin_rsp(work, (void *)rsp,
+					sizeof(struct smb2_close_rsp));
+
 	if (err) {
 		if (rsp->hdr.Status == 0)
 			rsp->hdr.Status = STATUS_FILE_CLOSED;
 		smb2_set_err_rsp(work);
-	} else {
-		inc_rfc1001_len(rsp_org, 60);
 	}
 
-	return 0;
+	return err;
 }
 
 /**
@@ -5320,55 +5521,31 @@
  */
 int smb2_echo(struct ksmbd_work *work)
 {
-	struct smb2_echo_rsp *rsp = work->response_buf;
+	struct smb2_echo_rsp *rsp = smb2_get_msg(work->response_buf);
+
+	if (work->next_smb2_rcv_hdr_off)
+		rsp = ksmbd_resp_buf_next(work);
 
 	rsp->StructureSize = cpu_to_le16(4);
 	rsp->Reserved = 0;
-	inc_rfc1001_len(rsp, 4);
-	return 0;
+	return ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_echo_rsp));
 }
 
 static int smb2_rename(struct ksmbd_work *work,
 		       struct ksmbd_file *fp,
-		       struct user_namespace *user_ns,
 		       struct smb2_file_rename_info *file_info,
 		       struct nls_table *local_nls)
 {
 	struct ksmbd_share_config *share = fp->tcon->share_conf;
-	char *new_name = NULL, *abs_oldname = NULL, *old_name = NULL;
-	char *pathname = NULL;
-	struct path path;
-	bool file_present = true;
-	int rc;
+	char *new_name = NULL;
+	int rc, flags = 0;
 
 	ksmbd_debug(SMB, "setting FILE_RENAME_INFO\n");
-	pathname = kmalloc(PATH_MAX, GFP_KERNEL);
-	if (!pathname)
-		return -ENOMEM;
-
-	abs_oldname = d_path(&fp->filp->f_path, pathname, PATH_MAX);
-	if (IS_ERR(abs_oldname)) {
-		rc = -EINVAL;
-		goto out;
-	}
-	old_name = strrchr(abs_oldname, '/');
-	if (old_name && old_name[1] != '\0') {
-		old_name++;
-	} else {
-		ksmbd_debug(SMB, "can't get last component in path %s\n",
-			    abs_oldname);
-		rc = -ENOENT;
-		goto out;
-	}
-
-	new_name = smb2_get_name(share,
-				 file_info->FileName,
+	new_name = smb2_get_name(file_info->FileName,
 				 le32_to_cpu(file_info->FileNameLength),
 				 local_nls);
-	if (IS_ERR(new_name)) {
-		rc = PTR_ERR(new_name);
-		goto out;
-	}
+	if (IS_ERR(new_name))
+		return PTR_ERR(new_name);
 
 	if (strchr(new_name, ':')) {
 		int s_type;
@@ -5394,10 +5571,10 @@
 		if (rc)
 			goto out;
 
-		rc = ksmbd_vfs_setxattr(user_ns,
-					fp->filp->f_path.dentry,
+		rc = ksmbd_vfs_setxattr(file_mnt_user_ns(fp->filp),
+					&fp->filp->f_path,
 					xattr_stream_name,
-					NULL, 0, 0);
+					NULL, 0, 0, true);
 		if (rc < 0) {
 			pr_err("failed to store stream name in xattr: %d\n",
 			       rc);
@@ -5409,47 +5586,20 @@
 	}
 
 	ksmbd_debug(SMB, "new name %s\n", new_name);
-	rc = ksmbd_vfs_kern_path(work, new_name, LOOKUP_NO_SYMLINKS, &path, 1);
-	if (rc) {
-		if (rc != -ENOENT)
-			goto out;
-		file_present = false;
-	} else {
-		path_put(&path);
-	}
-
 	if (ksmbd_share_veto_filename(share, new_name)) {
 		rc = -ENOENT;
 		ksmbd_debug(SMB, "Can't rename vetoed file: %s\n", new_name);
 		goto out;
 	}
 
-	if (file_info->ReplaceIfExists) {
-		if (file_present) {
-			rc = ksmbd_vfs_remove_file(work, new_name);
-			if (rc) {
-				if (rc != -ENOTEMPTY)
-					rc = -EINVAL;
-				ksmbd_debug(SMB, "cannot delete %s, rc %d\n",
-					    new_name, rc);
-				goto out;
-			}
-		}
-	} else {
-		if (file_present &&
-		    strncmp(old_name, path.dentry->d_name.name, strlen(old_name))) {
-			rc = -EEXIST;
-			ksmbd_debug(SMB,
-				    "cannot rename already existing file\n");
-			goto out;
-		}
-	}
+	if (!file_info->ReplaceIfExists)
+		flags = RENAME_NOREPLACE;
 
-	rc = ksmbd_vfs_fp_rename(work, fp, new_name);
+	rc = ksmbd_vfs_rename(work, &fp->filp->f_path, new_name, flags);
+	if (!rc)
+		smb_break_all_levII_oplock(work, fp, 0);
 out:
-	kfree(pathname);
-	if (!IS_ERR(new_name))
-		kfree(new_name);
+	kfree(new_name);
 	return rc;
 }
 
@@ -5460,8 +5610,8 @@
 			    struct nls_table *local_nls)
 {
 	char *link_name = NULL, *target_name = NULL, *pathname = NULL;
-	struct path path;
-	bool file_present = true;
+	struct path path, parent_path;
+	bool file_present = false;
 	int rc;
 
 	if (buf_len < (u64)sizeof(struct smb2_file_link_info) +
@@ -5473,8 +5623,7 @@
 	if (!pathname)
 		return -ENOMEM;
 
-	link_name = smb2_get_name(share,
-				  file_info->FileName,
+	link_name = smb2_get_name(file_info->FileName,
 				  le32_to_cpu(file_info->FileNameLength),
 				  local_nls);
 	if (IS_ERR(link_name) || S_ISDIR(file_inode(filp)->i_mode)) {
@@ -5483,25 +5632,24 @@
 	}
 
 	ksmbd_debug(SMB, "link name is %s\n", link_name);
-	target_name = d_path(&filp->f_path, pathname, PATH_MAX);
+	target_name = file_path(filp, pathname, PATH_MAX);
 	if (IS_ERR(target_name)) {
 		rc = -EINVAL;
 		goto out;
 	}
 
 	ksmbd_debug(SMB, "target name is %s\n", target_name);
-	rc = ksmbd_vfs_kern_path(work, link_name, LOOKUP_NO_SYMLINKS, &path, 0);
+	rc = ksmbd_vfs_kern_path_locked(work, link_name, LOOKUP_NO_SYMLINKS,
+					&parent_path, &path, 0);
 	if (rc) {
 		if (rc != -ENOENT)
 			goto out;
-		file_present = false;
-	} else {
-		path_put(&path);
-	}
+	} else
+		file_present = true;
 
 	if (file_info->ReplaceIfExists) {
 		if (file_present) {
-			rc = ksmbd_vfs_remove_file(work, link_name);
+			rc = ksmbd_vfs_remove_file(work, &path);
 			if (rc) {
 				rc = -EINVAL;
 				ksmbd_debug(SMB, "cannot delete %s\n",
@@ -5521,6 +5669,9 @@
 	if (rc)
 		rc = -EINVAL;
 out:
+	if (file_present)
+		ksmbd_vfs_kern_path_unlock(&parent_path, &path);
+
 	if (!IS_ERR(link_name))
 		kfree(link_name);
 	kfree(pathname);
@@ -5587,8 +5738,8 @@
 		da.flags = XATTR_DOSINFO_ATTRIB | XATTR_DOSINFO_CREATE_TIME |
 			XATTR_DOSINFO_ITIME;
 
-		rc = ksmbd_vfs_set_dos_attrib_xattr(user_ns,
-						    filp->f_path.dentry, &da);
+		rc = ksmbd_vfs_set_dos_attrib_xattr(user_ns, &filp->f_path, &da,
+				true);
 		if (rc)
 			ksmbd_debug(SMB,
 				    "failed to restore file attribute in EA\n");
@@ -5623,15 +5774,21 @@
 
 	loff_t alloc_blks;
 	struct inode *inode;
+	struct kstat stat;
 	int rc;
 
 	if (!(fp->daccess & FILE_WRITE_DATA_LE))
 		return -EACCES;
 
+	rc = vfs_getattr(&fp->filp->f_path, &stat, STATX_BASIC_STATS,
+			 AT_STATX_SYNC_AS_STAT);
+	if (rc)
+		return rc;
+
 	alloc_blks = (le64_to_cpu(file_alloc_info->AllocationSize) + 511) >> 9;
 	inode = file_inode(fp->filp);
 
-	if (alloc_blks > inode->i_blocks) {
+	if (alloc_blks > stat.blocks) {
 		smb_break_all_levII_oplock(work, fp, 1);
 		rc = vfs_fallocate(fp->filp, FALLOC_FL_KEEP_SIZE, 0,
 				   alloc_blks * 512);
@@ -5639,7 +5796,7 @@
 			pr_err("vfs_fallocate is failed : %d\n", rc);
 			return rc;
 		}
-	} else if (alloc_blks < inode->i_blocks) {
+	} else if (alloc_blks < stat.blocks) {
 		loff_t size;
 
 		/*
@@ -5652,8 +5809,7 @@
 		size = i_size_read(inode);
 		rc = ksmbd_vfs_truncate(work, fp, alloc_blks * 512);
 		if (rc) {
-			pr_err("truncate failed! filename : %s, err %d\n",
-			       fp->filename, rc);
+			pr_err("truncate failed!, err %d\n", rc);
 			return rc;
 		}
 		if (size < alloc_blks * 512)
@@ -5683,12 +5839,10 @@
 	 * truncated range.
 	 */
 	if (inode->i_sb->s_magic != MSDOS_SUPER_MAGIC) {
-		ksmbd_debug(SMB, "filename : %s truncated to newsize %lld\n",
-			    fp->filename, newsize);
+		ksmbd_debug(SMB, "truncated to newsize %lld\n", newsize);
 		rc = ksmbd_vfs_truncate(work, fp, newsize);
 		if (rc) {
-			ksmbd_debug(SMB, "truncate failed! filename : %s err %d\n",
-				    fp->filename, rc);
+			ksmbd_debug(SMB, "truncate failed!, err %d\n", rc);
 			if (rc != -EAGAIN)
 				rc = -EBADF;
 			return rc;
@@ -5701,12 +5855,6 @@
 			   struct smb2_file_rename_info *rename_info,
 			   unsigned int buf_len)
 {
-	struct user_namespace *user_ns;
-	struct ksmbd_file *parent_fp;
-	struct dentry *parent;
-	struct dentry *dentry = fp->filp->f_path.dentry;
-	int ret;
-
 	if (!(fp->daccess & FILE_DELETE_LE)) {
 		pr_err("no right to delete : 0x%x\n", fp->daccess);
 		return -EACCES;
@@ -5716,30 +5864,10 @@
 			le32_to_cpu(rename_info->FileNameLength))
 		return -EINVAL;
 
-	user_ns = file_mnt_user_ns(fp->filp);
-	if (ksmbd_stream_fd(fp))
-		goto next;
-
-	parent = dget_parent(dentry);
-	ret = ksmbd_vfs_lock_parent(user_ns, parent, dentry);
-	if (ret) {
-		dput(parent);
-		return ret;
-	}
+	if (!le32_to_cpu(rename_info->FileNameLength))
+		return -EINVAL;
 
-	parent_fp = ksmbd_lookup_fd_inode(d_inode(parent));
-	inode_unlock(d_inode(parent));
-	dput(parent);
-
-	if (parent_fp) {
-		if (parent_fp->daccess & FILE_DELETE_LE) {
-			pr_err("parent dir is opened with delete access\n");
-			return -ESHARE;
-		}
-	}
-next:
-	return smb2_rename(work, fp, user_ns, rename_info,
-			   work->sess->conn->local_nls);
+	return smb2_rename(work, fp, rename_info, work->conn->local_nls);
 }
 
 static int set_file_disposition_info(struct ksmbd_file *fp,
@@ -5814,7 +5942,7 @@
  * smb2_set_info_file() - handler for smb2 set info command
  * @work:	smb work containing set info command buffer
  * @fp:		ksmbd_file pointer
- * @info_class:	smb2 set info class
+ * @req:	request buffer pointer
  * @share:	ksmbd_share_config pointer
  *
  * Return:	0 on success, otherwise error
@@ -5825,6 +5953,7 @@
 			      struct ksmbd_share_config *share)
 {
 	unsigned int buf_len = le32_to_cpu(req->BufferLength);
+	char *buffer = (char *)req + le16_to_cpu(req->BufferOffset);
 
 	switch (req->FileInfoClass) {
 	case FILE_BASIC_INFORMATION:
@@ -5832,7 +5961,7 @@
 		if (buf_len < sizeof(struct smb2_file_basic_info))
 			return -EINVAL;
 
-		return set_file_basic_info(fp, (struct smb2_file_basic_info *)req->Buffer, share);
+		return set_file_basic_info(fp, (struct smb2_file_basic_info *)buffer, share);
 	}
 	case FILE_ALLOCATION_INFORMATION:
 	{
@@ -5840,7 +5969,7 @@
 			return -EINVAL;
 
 		return set_file_allocation_info(work, fp,
-						(struct smb2_file_alloc_info *)req->Buffer);
+						(struct smb2_file_alloc_info *)buffer);
 	}
 	case FILE_END_OF_FILE_INFORMATION:
 	{
@@ -5848,21 +5977,15 @@
 			return -EINVAL;
 
 		return set_end_of_file_info(work, fp,
-					    (struct smb2_file_eof_info *)req->Buffer);
+					    (struct smb2_file_eof_info *)buffer);
 	}
 	case FILE_RENAME_INFORMATION:
 	{
-		if (!test_tree_conn_flag(work->tcon, KSMBD_TREE_CONN_FLAG_WRITABLE)) {
-			ksmbd_debug(SMB,
-				    "User does not have write permission\n");
-			return -EACCES;
-		}
-
 		if (buf_len < sizeof(struct smb2_file_rename_info))
 			return -EINVAL;
 
 		return set_rename_info(work, fp,
-				       (struct smb2_file_rename_info *)req->Buffer,
+				       (struct smb2_file_rename_info *)buffer,
 				       buf_len);
 	}
 	case FILE_LINK_INFORMATION:
@@ -5871,23 +5994,17 @@
 			return -EINVAL;
 
 		return smb2_create_link(work, work->tcon->share_conf,
-					(struct smb2_file_link_info *)req->Buffer,
+					(struct smb2_file_link_info *)buffer,
 					buf_len, fp->filp,
-					work->sess->conn->local_nls);
+					work->conn->local_nls);
 	}
 	case FILE_DISPOSITION_INFORMATION:
 	{
-		if (!test_tree_conn_flag(work->tcon, KSMBD_TREE_CONN_FLAG_WRITABLE)) {
-			ksmbd_debug(SMB,
-				    "User does not have write permission\n");
-			return -EACCES;
-		}
-
 		if (buf_len < sizeof(struct smb2_file_disposition_info))
 			return -EINVAL;
 
 		return set_file_disposition_info(fp,
-						 (struct smb2_file_disposition_info *)req->Buffer);
+						 (struct smb2_file_disposition_info *)buffer);
 	}
 	case FILE_FULL_EA_INFORMATION:
 	{
@@ -5900,22 +6017,22 @@
 		if (buf_len < sizeof(struct smb2_ea_info))
 			return -EINVAL;
 
-		return smb2_set_ea((struct smb2_ea_info *)req->Buffer,
-				   buf_len, &fp->filp->f_path);
+		return smb2_set_ea((struct smb2_ea_info *)buffer,
+				   buf_len, &fp->filp->f_path, true);
 	}
 	case FILE_POSITION_INFORMATION:
 	{
 		if (buf_len < sizeof(struct smb2_file_pos_info))
 			return -EINVAL;
 
-		return set_file_position_info(fp, (struct smb2_file_pos_info *)req->Buffer);
+		return set_file_position_info(fp, (struct smb2_file_pos_info *)buffer);
 	}
 	case FILE_MODE_INFORMATION:
 	{
 		if (buf_len < sizeof(struct smb2_file_mode_info))
 			return -EINVAL;
 
-		return set_file_mode_info(fp, (struct smb2_file_mode_info *)req->Buffer);
+		return set_file_mode_info(fp, (struct smb2_file_mode_info *)buffer);
 	}
 	}
 
@@ -5931,7 +6048,7 @@
 	fp->saccess |= FILE_SHARE_DELETE_LE;
 
 	return set_info_sec(fp->conn, fp->tcon, &fp->filp->f_path, pntsd,
-			buf_len, false);
+			buf_len, false, true);
 }
 
 /**
@@ -5943,31 +6060,37 @@
 int smb2_set_info(struct ksmbd_work *work)
 {
 	struct smb2_set_info_req *req;
-	struct smb2_set_info_rsp *rsp, *rsp_org;
-	struct ksmbd_file *fp;
+	struct smb2_set_info_rsp *rsp;
+	struct ksmbd_file *fp = NULL;
 	int rc = 0;
 	unsigned int id = KSMBD_NO_FID, pid = KSMBD_NO_FID;
 
 	ksmbd_debug(SMB, "Received set info request\n");
 
-	rsp_org = work->response_buf;
 	if (work->next_smb2_rcv_hdr_off) {
 		req = ksmbd_req_buf_next(work);
 		rsp = ksmbd_resp_buf_next(work);
-		if (!has_file_id(le64_to_cpu(req->VolatileFileId))) {
+		if (!has_file_id(req->VolatileFileId)) {
 			ksmbd_debug(SMB, "Compound request set FID = %llu\n",
 				    work->compound_fid);
 			id = work->compound_fid;
 			pid = work->compound_pfid;
 		}
 	} else {
-		req = work->request_buf;
-		rsp = work->response_buf;
+		req = smb2_get_msg(work->request_buf);
+		rsp = smb2_get_msg(work->response_buf);
+	}
+
+	if (!test_tree_conn_flag(work->tcon, KSMBD_TREE_CONN_FLAG_WRITABLE)) {
+		ksmbd_debug(SMB, "User does not have write permission\n");
+		pr_err("User does not have write permission\n");
+		rc = -EACCES;
+		goto err_out;
 	}
 
 	if (!has_file_id(id)) {
-		id = le64_to_cpu(req->VolatileFileId);
-		pid = le64_to_cpu(req->PersistentFileId);
+		id = req->VolatileFileId;
+		pid = req->PersistentFileId;
 	}
 
 	fp = ksmbd_lookup_fd_slow(work, id, pid);
@@ -5990,7 +6113,7 @@
 		}
 		rc = smb2_set_info_sec(fp,
 				       le32_to_cpu(req->AdditionalInformation),
-				       req->Buffer,
+				       (char *)req + le16_to_cpu(req->BufferOffset),
 				       le32_to_cpu(req->BufferLength));
 		ksmbd_revert_fsids(work);
 		break;
@@ -6002,7 +6125,10 @@
 		goto err_out;
 
 	rsp->StructureSize = cpu_to_le16(2);
-	inc_rfc1001_len(rsp_org, 2);
+	rc = ksmbd_iov_pin_rsp(work, (void *)rsp,
+			       sizeof(struct smb2_set_info_rsp));
+	if (rc)
+		goto err_out;
 	ksmbd_fd_put(work, fp);
 	return 0;
 
@@ -6042,33 +6168,45 @@
 	int nbytes = 0, err;
 	u64 id;
 	struct ksmbd_rpc_command *rpc_resp;
-	struct smb2_read_req *req = work->request_buf;
-	struct smb2_read_rsp *rsp = work->response_buf;
+	struct smb2_read_req *req;
+	struct smb2_read_rsp *rsp;
+
+	WORK_BUFFERS(work, req, rsp);
 
-	id = le64_to_cpu(req->VolatileFileId);
+	id = req->VolatileFileId;
 
-	inc_rfc1001_len(rsp, 16);
 	rpc_resp = ksmbd_rpc_read(work->sess, id);
 	if (rpc_resp) {
+		void *aux_payload_buf;
+
 		if (rpc_resp->flags != KSMBD_RPC_OK) {
 			err = -EINVAL;
 			goto out;
 		}
 
-		work->aux_payload_buf =
-			kvmalloc(rpc_resp->payload_sz, GFP_KERNEL | __GFP_ZERO);
-		if (!work->aux_payload_buf) {
+		aux_payload_buf =
+			kvmalloc(rpc_resp->payload_sz, GFP_KERNEL);
+		if (!aux_payload_buf) {
 			err = -ENOMEM;
 			goto out;
 		}
 
-		memcpy(work->aux_payload_buf, rpc_resp->payload,
-		       rpc_resp->payload_sz);
+		memcpy(aux_payload_buf, rpc_resp->payload, rpc_resp->payload_sz);
 
 		nbytes = rpc_resp->payload_sz;
-		work->resp_hdr_sz = get_rfc1002_len(rsp) + 4;
-		work->aux_payload_sz = nbytes;
+		err = ksmbd_iov_pin_rsp_read(work, (void *)rsp,
+					     offsetof(struct smb2_read_rsp, Buffer),
+					     aux_payload_buf, nbytes);
+		if (err) {
+			kvfree(aux_payload_buf);
+			goto out;
+		}
 		kvfree(rpc_resp);
+	} else {
+		err = ksmbd_iov_pin_rsp(work, (void *)rsp,
+					offsetof(struct smb2_read_rsp, Buffer));
+		if (err)
+			goto out;
 	}
 
 	rsp->StructureSize = cpu_to_le16(17);
@@ -6077,7 +6215,6 @@
 	rsp->DataLength = cpu_to_le32(nbytes);
 	rsp->DataRemaining = 0;
 	rsp->Reserved2 = 0;
-	inc_rfc1001_len(rsp, nbytes);
 	return 0;
 
 out:
@@ -6087,30 +6224,46 @@
 	return err;
 }
 
-static ssize_t smb2_read_rdma_channel(struct ksmbd_work *work,
-				      struct smb2_read_req *req, void *data_buf,
-				      size_t length)
+static int smb2_set_remote_key_for_rdma(struct ksmbd_work *work,
+					struct smb2_buffer_desc_v1 *desc,
+					__le32 Channel,
+					__le16 ChannelInfoLength)
 {
-	struct smb2_buffer_desc_v1 *desc =
-		(struct smb2_buffer_desc_v1 *)&req->Buffer[0];
-	int err;
+	unsigned int i, ch_count;
 
 	if (work->conn->dialect == SMB30_PROT_ID &&
-	    req->Channel != SMB2_CHANNEL_RDMA_V1)
+	    Channel != SMB2_CHANNEL_RDMA_V1)
 		return -EINVAL;
 
-	if (req->ReadChannelInfoOffset == 0 ||
-	    le16_to_cpu(req->ReadChannelInfoLength) < sizeof(*desc))
+	ch_count = le16_to_cpu(ChannelInfoLength) / sizeof(*desc);
+	if (ksmbd_debug_types & KSMBD_DEBUG_RDMA) {
+		for (i = 0; i < ch_count; i++) {
+			pr_info("RDMA r/w request %#x: token %#x, length %#x\n",
+				i,
+				le32_to_cpu(desc[i].token),
+				le32_to_cpu(desc[i].length));
+		}
+	}
+	if (!ch_count)
 		return -EINVAL;
 
 	work->need_invalidate_rkey =
-		(req->Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE);
-	work->remote_key = le32_to_cpu(desc->token);
+		(Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE);
+	if (Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE)
+		work->remote_key = le32_to_cpu(desc->token);
+	return 0;
+}
+
+static ssize_t smb2_read_rdma_channel(struct ksmbd_work *work,
+				      struct smb2_read_req *req, void *data_buf,
+				      size_t length)
+{
+	int err;
 
 	err = ksmbd_conn_rdma_write(work->conn, data_buf, length,
-				    le32_to_cpu(desc->token),
-				    le64_to_cpu(desc->offset),
-				    le32_to_cpu(desc->length));
+				    (struct smb2_buffer_desc_v1 *)
+				    ((char *)req + le16_to_cpu(req->ReadChannelInfoOffset)),
+				    le16_to_cpu(req->ReadChannelInfoLength));
 	if (err)
 		return err;
 
@@ -6127,15 +6280,16 @@
 {
 	struct ksmbd_conn *conn = work->conn;
 	struct smb2_read_req *req;
-	struct smb2_read_rsp *rsp, *rsp_org;
-	struct ksmbd_file *fp;
+	struct smb2_read_rsp *rsp;
+	struct ksmbd_file *fp = NULL;
 	loff_t offset;
 	size_t length, mincount;
 	ssize_t nbytes = 0, remain_bytes = 0;
 	int err = 0;
-
-	rsp_org = work->response_buf;
-	WORK_BUFFERS(work, req, rsp);
+	bool is_rdma_channel = false;
+	unsigned int max_read_size = conn->vals->max_read_size;
+	unsigned int id = KSMBD_NO_FID, pid = KSMBD_NO_FID;
+	void *aux_payload_buf;
 
 	if (test_share_config_flag(work->tcon->share_conf,
 				   KSMBD_SHARE_FLAG_PIPE)) {
@@ -6143,8 +6297,48 @@
 		return smb2_read_pipe(work);
 	}
 
-	fp = ksmbd_lookup_fd_slow(work, le64_to_cpu(req->VolatileFileId),
-				  le64_to_cpu(req->PersistentFileId));
+	if (work->next_smb2_rcv_hdr_off) {
+		req = ksmbd_req_buf_next(work);
+		rsp = ksmbd_resp_buf_next(work);
+		if (!has_file_id(req->VolatileFileId)) {
+			ksmbd_debug(SMB, "Compound request set FID = %llu\n",
+					work->compound_fid);
+			id = work->compound_fid;
+			pid = work->compound_pfid;
+		}
+	} else {
+		req = smb2_get_msg(work->request_buf);
+		rsp = smb2_get_msg(work->response_buf);
+	}
+
+	if (!has_file_id(id)) {
+		id = req->VolatileFileId;
+		pid = req->PersistentFileId;
+	}
+
+	if (req->Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE ||
+	    req->Channel == SMB2_CHANNEL_RDMA_V1) {
+		is_rdma_channel = true;
+		max_read_size = get_smbd_max_read_write_size();
+	}
+
+	if (is_rdma_channel == true) {
+		unsigned int ch_offset = le16_to_cpu(req->ReadChannelInfoOffset);
+
+		if (ch_offset < offsetof(struct smb2_read_req, Buffer)) {
+			err = -EINVAL;
+			goto out;
+		}
+		err = smb2_set_remote_key_for_rdma(work,
+						   (struct smb2_buffer_desc_v1 *)
+						   ((char *)req + ch_offset),
+						   req->Channel,
+						   req->ReadChannelInfoLength);
+		if (err)
+			goto out;
+	}
+
+	fp = ksmbd_lookup_fd_slow(work, id, pid);
 	if (!fp) {
 		err = -ENOENT;
 		goto out;
@@ -6157,34 +6351,37 @@
 	}
 
 	offset = le64_to_cpu(req->Offset);
+	if (offset < 0) {
+		err = -EINVAL;
+		goto out;
+	}
 	length = le32_to_cpu(req->Length);
 	mincount = le32_to_cpu(req->MinimumCount);
 
-	if (length > conn->vals->max_read_size) {
+	if (length > max_read_size) {
 		ksmbd_debug(SMB, "limiting read size to max size(%u)\n",
-			    conn->vals->max_read_size);
+			    max_read_size);
 		err = -EINVAL;
 		goto out;
 	}
 
-	ksmbd_debug(SMB, "filename %pd, offset %lld, len %zu\n",
-		    fp->filp->f_path.dentry, offset, length);
+	ksmbd_debug(SMB, "filename %pD, offset %lld, len %zu\n",
+		    fp->filp, offset, length);
 
-	work->aux_payload_buf = kvmalloc(length, GFP_KERNEL | __GFP_ZERO);
-	if (!work->aux_payload_buf) {
+	aux_payload_buf = kvzalloc(length, GFP_KERNEL);
+	if (!aux_payload_buf) {
 		err = -ENOMEM;
 		goto out;
 	}
 
-	nbytes = ksmbd_vfs_read(work, fp, length, &offset);
+	nbytes = ksmbd_vfs_read(work, fp, length, &offset, aux_payload_buf);
 	if (nbytes < 0) {
 		err = nbytes;
 		goto out;
 	}
 
 	if ((nbytes == 0 && length != 0) || nbytes < mincount) {
-		kvfree(work->aux_payload_buf);
-		work->aux_payload_buf = NULL;
+		kvfree(aux_payload_buf);
 		rsp->hdr.Status = STATUS_END_OF_FILE;
 		smb2_set_err_rsp(work);
 		ksmbd_fd_put(work, fp);
@@ -6194,15 +6391,13 @@
 	ksmbd_debug(SMB, "nbytes %zu, offset %lld mincount %zu\n",
 		    nbytes, offset, mincount);
 
-	if (req->Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE ||
-	    req->Channel == SMB2_CHANNEL_RDMA_V1) {
+	if (is_rdma_channel == true) {
 		/* write data to the client using rdma channel */
 		remain_bytes = smb2_read_rdma_channel(work, req,
-						      work->aux_payload_buf,
+						      aux_payload_buf,
 						      nbytes);
-		kvfree(work->aux_payload_buf);
-		work->aux_payload_buf = NULL;
-
+		kvfree(aux_payload_buf);
+		aux_payload_buf = NULL;
 		nbytes = 0;
 		if (remain_bytes < 0) {
 			err = (int)remain_bytes;
@@ -6216,10 +6411,13 @@
 	rsp->DataLength = cpu_to_le32(nbytes);
 	rsp->DataRemaining = cpu_to_le32(remain_bytes);
 	rsp->Reserved2 = 0;
-	inc_rfc1001_len(rsp_org, 16);
-	work->resp_hdr_sz = get_rfc1002_len(rsp_org) + 4;
-	work->aux_payload_sz = nbytes;
-	inc_rfc1001_len(rsp_org, nbytes);
+	err = ksmbd_iov_pin_rsp_read(work, (void *)rsp,
+				     offsetof(struct smb2_read_rsp, Buffer),
+				     aux_payload_buf, nbytes);
+	if (err) {
+		kvfree(aux_payload_buf);
+		goto out;
+	}
 	ksmbd_fd_put(work, fp);
 	return 0;
 
@@ -6254,33 +6452,31 @@
  */
 static noinline int smb2_write_pipe(struct ksmbd_work *work)
 {
-	struct smb2_write_req *req = work->request_buf;
-	struct smb2_write_rsp *rsp = work->response_buf;
+	struct smb2_write_req *req;
+	struct smb2_write_rsp *rsp;
 	struct ksmbd_rpc_command *rpc_resp;
 	u64 id = 0;
 	int err = 0, ret = 0;
 	char *data_buf;
 	size_t length;
 
-	length = le32_to_cpu(req->Length);
-	id = le64_to_cpu(req->VolatileFileId);
+	WORK_BUFFERS(work, req, rsp);
 
-	if (le16_to_cpu(req->DataOffset) ==
-	    (offsetof(struct smb2_write_req, Buffer) - 4)) {
-		data_buf = (char *)&req->Buffer[0];
-	} else {
-		if ((u64)le16_to_cpu(req->DataOffset) + length > get_rfc1002_len(req)) {
-			pr_err("invalid write data offset %u, smb_len %u\n",
-			       le16_to_cpu(req->DataOffset),
-			       get_rfc1002_len(req));
-			err = -EINVAL;
-			goto out;
-		}
+	length = le32_to_cpu(req->Length);
+	id = req->VolatileFileId;
 
-		data_buf = (char *)(((char *)&req->hdr.ProtocolId) +
-				le16_to_cpu(req->DataOffset));
+	if ((u64)le16_to_cpu(req->DataOffset) + length >
+	    get_rfc1002_len(work->request_buf)) {
+		pr_err("invalid write data offset %u, smb_len %u\n",
+		       le16_to_cpu(req->DataOffset),
+		       get_rfc1002_len(work->request_buf));
+		err = -EINVAL;
+		goto out;
 	}
 
+	data_buf = (char *)(((char *)&req->hdr.ProtocolId) +
+			le16_to_cpu(req->DataOffset));
+
 	rpc_resp = ksmbd_rpc_write(work->sess, id, data_buf, length);
 	if (rpc_resp) {
 		if (rpc_resp->flags == KSMBD_RPC_ENOTIMPLEMENTED) {
@@ -6304,8 +6500,8 @@
 	rsp->DataLength = cpu_to_le32(length);
 	rsp->DataRemaining = 0;
 	rsp->Reserved2 = 0;
-	inc_rfc1001_len(rsp, 16);
-	return 0;
+	err = ksmbd_iov_pin_rsp(work, (void *)rsp,
+				offsetof(struct smb2_write_rsp, Buffer));
 out:
 	if (err) {
 		rsp->hdr.Status = STATUS_INVALID_HANDLE;
@@ -6320,36 +6516,18 @@
 				       struct ksmbd_file *fp,
 				       loff_t offset, size_t length, bool sync)
 {
-	struct smb2_buffer_desc_v1 *desc;
 	char *data_buf;
 	int ret;
 	ssize_t nbytes;
 
-	desc = (struct smb2_buffer_desc_v1 *)&req->Buffer[0];
-
-	if (work->conn->dialect == SMB30_PROT_ID &&
-	    req->Channel != SMB2_CHANNEL_RDMA_V1)
-		return -EINVAL;
-
-	if (req->Length != 0 || req->DataOffset != 0)
-		return -EINVAL;
-
-	if (req->WriteChannelInfoOffset == 0 ||
-	    le16_to_cpu(req->WriteChannelInfoLength) < sizeof(*desc))
-		return -EINVAL;
-
-	work->need_invalidate_rkey =
-		(req->Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE);
-	work->remote_key = le32_to_cpu(desc->token);
-
-	data_buf = kvmalloc(length, GFP_KERNEL | __GFP_ZERO);
+	data_buf = kvzalloc(length, GFP_KERNEL);
 	if (!data_buf)
 		return -ENOMEM;
 
 	ret = ksmbd_conn_rdma_read(work->conn, data_buf, length,
-				   le32_to_cpu(desc->token),
-				   le64_to_cpu(desc->offset),
-				   le32_to_cpu(desc->length));
+				   (struct smb2_buffer_desc_v1 *)
+				   ((char *)req + le16_to_cpu(req->WriteChannelInfoOffset)),
+				   le16_to_cpu(req->WriteChannelInfoLength));
 	if (ret < 0) {
 		kvfree(data_buf);
 		return ret;
@@ -6372,16 +6550,16 @@
 int smb2_write(struct ksmbd_work *work)
 {
 	struct smb2_write_req *req;
-	struct smb2_write_rsp *rsp, *rsp_org;
+	struct smb2_write_rsp *rsp;
 	struct ksmbd_file *fp = NULL;
 	loff_t offset;
 	size_t length;
 	ssize_t nbytes;
 	char *data_buf;
-	bool writethrough = false;
+	bool writethrough = false, is_rdma_channel = false;
 	int err = 0;
+	unsigned int max_write_size = work->conn->vals->max_write_size;
 
-	rsp_org = work->response_buf;
 	WORK_BUFFERS(work, req, rsp);
 
 	if (test_share_config_flag(work->tcon->share_conf, KSMBD_SHARE_FLAG_PIPE)) {
@@ -6389,14 +6567,42 @@
 		return smb2_write_pipe(work);
 	}
 
+	offset = le64_to_cpu(req->Offset);
+	if (offset < 0)
+		return -EINVAL;
+	length = le32_to_cpu(req->Length);
+
+	if (req->Channel == SMB2_CHANNEL_RDMA_V1 ||
+	    req->Channel == SMB2_CHANNEL_RDMA_V1_INVALIDATE) {
+		is_rdma_channel = true;
+		max_write_size = get_smbd_max_read_write_size();
+		length = le32_to_cpu(req->RemainingBytes);
+	}
+
+	if (is_rdma_channel == true) {
+		unsigned int ch_offset = le16_to_cpu(req->WriteChannelInfoOffset);
+
+		if (req->Length != 0 || req->DataOffset != 0 ||
+		    ch_offset < offsetof(struct smb2_write_req, Buffer)) {
+			err = -EINVAL;
+			goto out;
+		}
+		err = smb2_set_remote_key_for_rdma(work,
+						   (struct smb2_buffer_desc_v1 *)
+						   ((char *)req + ch_offset),
+						   req->Channel,
+						   req->WriteChannelInfoLength);
+		if (err)
+			goto out;
+	}
+
 	if (!test_tree_conn_flag(work->tcon, KSMBD_TREE_CONN_FLAG_WRITABLE)) {
 		ksmbd_debug(SMB, "User does not have write permission\n");
 		err = -EACCES;
 		goto out;
 	}
 
-	fp = ksmbd_lookup_fd_slow(work, le64_to_cpu(req->VolatileFileId),
-				  le64_to_cpu(req->PersistentFileId));
+	fp = ksmbd_lookup_fd_slow(work, req->VolatileFileId, req->PersistentFileId);
 	if (!fp) {
 		err = -ENOENT;
 		goto out;
@@ -6408,43 +6614,29 @@
 		goto out;
 	}
 
-	offset = le64_to_cpu(req->Offset);
-	length = le32_to_cpu(req->Length);
-
-	if (length > work->conn->vals->max_write_size) {
+	if (length > max_write_size) {
 		ksmbd_debug(SMB, "limiting write size to max size(%u)\n",
-			    work->conn->vals->max_write_size);
+			    max_write_size);
 		err = -EINVAL;
 		goto out;
 	}
 
+	ksmbd_debug(SMB, "flags %u\n", le32_to_cpu(req->Flags));
 	if (le32_to_cpu(req->Flags) & SMB2_WRITEFLAG_WRITE_THROUGH)
 		writethrough = true;
 
-	if (req->Channel != SMB2_CHANNEL_RDMA_V1 &&
-	    req->Channel != SMB2_CHANNEL_RDMA_V1_INVALIDATE) {
-		if (le16_to_cpu(req->DataOffset) ==
-		    (offsetof(struct smb2_write_req, Buffer) - 4)) {
-			data_buf = (char *)&req->Buffer[0];
-		} else {
-			if ((u64)le16_to_cpu(req->DataOffset) + length > get_rfc1002_len(req)) {
-				pr_err("invalid write data offset %u, smb_len %u\n",
-				       le16_to_cpu(req->DataOffset),
-				       get_rfc1002_len(req));
-				err = -EINVAL;
-				goto out;
-			}
-
-			data_buf = (char *)(((char *)&req->hdr.ProtocolId) +
-					le16_to_cpu(req->DataOffset));
+	if (is_rdma_channel == false) {
+		if (le16_to_cpu(req->DataOffset) <
+		    offsetof(struct smb2_write_req, Buffer)) {
+			err = -EINVAL;
+			goto out;
 		}
 
-		ksmbd_debug(SMB, "flags %u\n", le32_to_cpu(req->Flags));
-		if (le32_to_cpu(req->Flags) & SMB2_WRITEFLAG_WRITE_THROUGH)
-			writethrough = true;
+		data_buf = (char *)(((char *)&req->hdr.ProtocolId) +
+				le16_to_cpu(req->DataOffset));
 
-		ksmbd_debug(SMB, "filename %pd, offset %lld, len %zu\n",
-			    fp->filp->f_path.dentry, offset, length);
+		ksmbd_debug(SMB, "filename %pD, offset %lld, len %zu\n",
+			    fp->filp, offset, length);
 		err = ksmbd_vfs_write(work, fp, data_buf, length, &offset,
 				      writethrough, &nbytes);
 		if (err < 0)
@@ -6453,8 +6645,7 @@
 		/* read data from the client using rdma channel, and
 		 * write the data.
 		 */
-		nbytes = smb2_write_rdma_channel(work, req, fp, offset,
-						 le32_to_cpu(req->RemainingBytes),
+		nbytes = smb2_write_rdma_channel(work, req, fp, offset, length,
 						 writethrough);
 		if (nbytes < 0) {
 			err = (int)nbytes;
@@ -6468,7 +6659,9 @@
 	rsp->DataLength = cpu_to_le32(nbytes);
 	rsp->DataRemaining = 0;
 	rsp->Reserved2 = 0;
-	inc_rfc1001_len(rsp_org, 16);
+	err = ksmbd_iov_pin_rsp(work, rsp, offsetof(struct smb2_write_rsp, Buffer));
+	if (err)
+		goto out;
 	ksmbd_fd_put(work, fp);
 	return 0;
 
@@ -6502,32 +6695,24 @@
 int smb2_flush(struct ksmbd_work *work)
 {
 	struct smb2_flush_req *req;
-	struct smb2_flush_rsp *rsp, *rsp_org;
+	struct smb2_flush_rsp *rsp;
 	int err;
 
-	rsp_org = work->response_buf;
 	WORK_BUFFERS(work, req, rsp);
 
-	ksmbd_debug(SMB, "SMB2_FLUSH called for fid %llu\n",
-		    le64_to_cpu(req->VolatileFileId));
+	ksmbd_debug(SMB, "SMB2_FLUSH called for fid %llu\n", req->VolatileFileId);
 
-	err = ksmbd_vfs_fsync(work,
-			      le64_to_cpu(req->VolatileFileId),
-			      le64_to_cpu(req->PersistentFileId));
+	err = ksmbd_vfs_fsync(work, req->VolatileFileId, req->PersistentFileId);
 	if (err)
 		goto out;
 
 	rsp->StructureSize = cpu_to_le16(4);
 	rsp->Reserved = 0;
-	inc_rfc1001_len(rsp_org, 4);
-	return 0;
+	return ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_flush_rsp));
 
 out:
-	if (err) {
-		rsp->hdr.Status = STATUS_INVALID_HANDLE;
-		smb2_set_err_rsp(work);
-	}
-
+	rsp->hdr.Status = STATUS_INVALID_HANDLE;
+	smb2_set_err_rsp(work);
 	return err;
 }
 
@@ -6540,12 +6725,14 @@
 int smb2_cancel(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_hdr *hdr = work->request_buf;
+	struct smb2_hdr *hdr = smb2_get_msg(work->request_buf);
 	struct smb2_hdr *chdr;
-	struct ksmbd_work *cancel_work = NULL;
-	int canceled = 0;
+	struct ksmbd_work *iter;
 	struct list_head *command_list;
 
+	if (work->next_smb2_rcv_hdr_off)
+		hdr = ksmbd_resp_buf_next(work);
+
 	ksmbd_debug(SMB, "smb2 cancel called on mid %llu, async flags 0x%x\n",
 		    hdr->MessageId, hdr->Flags);
 
@@ -6553,11 +6740,11 @@
 		command_list = &conn->async_requests;
 
 		spin_lock(&conn->request_lock);
-		list_for_each_entry(cancel_work, command_list,
+		list_for_each_entry(iter, command_list,
 				    async_request_entry) {
-			chdr = cancel_work->request_buf;
+			chdr = smb2_get_msg(iter->request_buf);
 
-			if (cancel_work->async_id !=
+			if (iter->async_id !=
 			    le64_to_cpu(hdr->Id.AsyncId))
 				continue;
 
@@ -6565,7 +6752,9 @@
 				    "smb2 with AsyncId %llu cancelled command = 0x%x\n",
 				    le64_to_cpu(hdr->Id.AsyncId),
 				    le16_to_cpu(chdr->Command));
-			canceled = 1;
+			iter->state = KSMBD_WORK_CANCELLED;
+			if (iter->cancel_fn)
+				iter->cancel_fn(iter->cancel_argv);
 			break;
 		}
 		spin_unlock(&conn->request_lock);
@@ -6573,29 +6762,23 @@
 		command_list = &conn->requests;
 
 		spin_lock(&conn->request_lock);
-		list_for_each_entry(cancel_work, command_list, request_entry) {
-			chdr = cancel_work->request_buf;
+		list_for_each_entry(iter, command_list, request_entry) {
+			chdr = smb2_get_msg(iter->request_buf);
 
 			if (chdr->MessageId != hdr->MessageId ||
-			    cancel_work == work)
+			    iter == work)
 				continue;
 
 			ksmbd_debug(SMB,
 				    "smb2 with mid %llu cancelled command = 0x%x\n",
 				    le64_to_cpu(hdr->MessageId),
 				    le16_to_cpu(chdr->Command));
-			canceled = 1;
+			iter->state = KSMBD_WORK_CANCELLED;
 			break;
 		}
 		spin_unlock(&conn->request_lock);
 	}
 
-	if (canceled) {
-		cancel_work->state = KSMBD_WORK_CANCELLED;
-		if (cancel_work->cancel_fn)
-			cancel_work->cancel_fn(cancel_work->cancel_argv);
-	}
-
 	/* For SMB2_CANCEL command itself send no response*/
 	work->send_no_response = 1;
 	return 0;
@@ -6655,7 +6838,7 @@
 	case SMB2_LOCKFLAG_UNLOCK:
 		ksmbd_debug(SMB, "received unlock request\n");
 		flock->fl_type = F_UNLCK;
-		cmd = 0;
+		cmd = F_SETLK;
 		break;
 	}
 
@@ -6709,8 +6892,8 @@
  */
 int smb2_lock(struct ksmbd_work *work)
 {
-	struct smb2_lock_req *req = work->request_buf;
-	struct smb2_lock_rsp *rsp = work->response_buf;
+	struct smb2_lock_req *req;
+	struct smb2_lock_rsp *rsp;
 	struct smb2_lock_element *lock_ele;
 	struct ksmbd_file *fp = NULL;
 	struct file_lock *flock = NULL;
@@ -6727,13 +6910,12 @@
 	LIST_HEAD(rollback_list);
 	int prior_lock = 0;
 
+	WORK_BUFFERS(work, req, rsp);
+
 	ksmbd_debug(SMB, "Received lock request\n");
-	fp = ksmbd_lookup_fd_slow(work,
-				  le64_to_cpu(req->VolatileFileId),
-				  le64_to_cpu(req->PersistentFileId));
+	fp = ksmbd_lookup_fd_slow(work, req->VolatileFileId, req->PersistentFileId);
 	if (!fp) {
-		ksmbd_debug(SMB, "Invalid file id for lock : %llu\n",
-			    le64_to_cpu(req->VolatileFileId));
+		ksmbd_debug(SMB, "Invalid file id for lock : %llu\n", req->VolatileFileId);
 		err = -ENOENT;
 		goto out2;
 	}
@@ -6762,6 +6944,7 @@
 		if (lock_start > U64_MAX - lock_length) {
 			pr_err("Invalid lock range requested\n");
 			rsp->hdr.Status = STATUS_INVALID_LOCK_RANGE;
+			locks_free_lock(flock);
 			goto out;
 		}
 
@@ -6781,6 +6964,7 @@
 				    "the end offset(%llx) is smaller than the start offset(%llx)\n",
 				    flock->fl_end, flock->fl_start);
 			rsp->hdr.Status = STATUS_INVALID_LOCK_RANGE;
+			locks_free_lock(flock);
 			goto out;
 		}
 
@@ -6792,6 +6976,7 @@
 				    flock->fl_type != F_UNLCK) {
 					pr_err("conflict two locks in one request\n");
 					err = -EINVAL;
+					locks_free_lock(flock);
 					goto out;
 				}
 			}
@@ -6800,6 +6985,7 @@
 		smb_lock = smb2_lock_init(flock, cmd, flags, &lock_list);
 		if (!smb_lock) {
 			err = -EINVAL;
+			locks_free_lock(flock);
 			goto out;
 		}
 	}
@@ -6831,7 +7017,7 @@
 
 		nolock = 1;
 		/* check locks in connection list */
-		read_lock(&conn_list_lock);
+		down_read(&conn_list_lock);
 		list_for_each_entry(conn, &conn_list, conns_list) {
 			spin_lock(&conn->llist_lock);
 			list_for_each_entry_safe(cmp_lock, tmp2, &conn->lock_list, clist) {
@@ -6848,7 +7034,7 @@
 						list_del(&cmp_lock->flist);
 						list_del(&cmp_lock->clist);
 						spin_unlock(&conn->llist_lock);
-						read_unlock(&conn_list_lock);
+						up_read(&conn_list_lock);
 
 						locks_free_lock(cmp_lock->fl);
 						kfree(cmp_lock);
@@ -6870,7 +7056,7 @@
 				    cmp_lock->start > smb_lock->start &&
 				    cmp_lock->start < smb_lock->end) {
 					spin_unlock(&conn->llist_lock);
-					read_unlock(&conn_list_lock);
+					up_read(&conn_list_lock);
 					pr_err("previous lock conflict with zero byte lock range\n");
 					goto out;
 				}
@@ -6879,7 +7065,7 @@
 				    smb_lock->start > cmp_lock->start &&
 				    smb_lock->start < cmp_lock->end) {
 					spin_unlock(&conn->llist_lock);
-					read_unlock(&conn_list_lock);
+					up_read(&conn_list_lock);
 					pr_err("current lock conflict with zero byte lock range\n");
 					goto out;
 				}
@@ -6890,14 +7076,14 @@
 				      cmp_lock->end >= smb_lock->end)) &&
 				    !cmp_lock->zero_len && !smb_lock->zero_len) {
 					spin_unlock(&conn->llist_lock);
-					read_unlock(&conn_list_lock);
+					up_read(&conn_list_lock);
 					pr_err("Not allow lock operation on exclusive lock range\n");
 					goto out;
 				}
 			}
 			spin_unlock(&conn->llist_lock);
 		}
-		read_unlock(&conn_list_lock);
+		up_read(&conn_list_lock);
 out_check_cl:
 		if (smb_lock->fl->fl_type == F_UNLCK && nolock) {
 			pr_err("Try to unlock nolocked range\n");
@@ -6931,10 +7117,6 @@
 
 				ksmbd_debug(SMB,
 					    "would have to wait for getting lock\n");
-				spin_lock(&work->conn->llist_lock);
-				list_add_tail(&smb_lock->clist,
-					      &work->conn->lock_list);
-				spin_unlock(&work->conn->llist_lock);
 				list_add(&smb_lock->llist, &rollback_list);
 
 				argv = kmalloc(sizeof(void *), GFP_KERNEL);
@@ -6948,6 +7130,7 @@
 						      smb2_remove_blocked_lock,
 						      argv);
 				if (rc) {
+					kfree(argv);
 					err = -ENOMEM;
 					goto out;
 				}
@@ -6959,17 +7142,15 @@
 
 				ksmbd_vfs_posix_lock_wait(flock);
 
+				spin_lock(&fp->f_lock);
+				list_del(&work->fp_entry);
+				spin_unlock(&fp->f_lock);
+
 				if (work->state != KSMBD_WORK_ACTIVE) {
 					list_del(&smb_lock->llist);
-					spin_lock(&work->conn->llist_lock);
-					list_del(&smb_lock->clist);
-					spin_unlock(&work->conn->llist_lock);
 					locks_free_lock(flock);
 
 					if (work->state == KSMBD_WORK_CANCELLED) {
-						spin_lock(&fp->f_lock);
-						list_del(&work->fp_entry);
-						spin_unlock(&fp->f_lock);
 						rsp->hdr.Status =
 							STATUS_CANCELLED;
 						kfree(smb_lock);
@@ -6978,8 +7159,7 @@
 						work->send_no_response = 1;
 						goto out;
 					}
-					init_smb2_rsp_hdr(work);
-					smb2_set_err_rsp(work);
+
 					rsp->hdr.Status =
 						STATUS_RANGE_NOT_LOCKED;
 					kfree(smb_lock);
@@ -6987,22 +7167,16 @@
 				}
 
 				list_del(&smb_lock->llist);
-				spin_lock(&work->conn->llist_lock);
-				list_del(&smb_lock->clist);
-				spin_unlock(&work->conn->llist_lock);
-
-				spin_lock(&fp->f_lock);
-				list_del(&work->fp_entry);
-				spin_unlock(&fp->f_lock);
+				release_async_work(work);
 				goto retry;
 			} else if (!rc) {
+				list_add(&smb_lock->llist, &rollback_list);
 				spin_lock(&work->conn->llist_lock);
 				list_add_tail(&smb_lock->clist,
 					      &work->conn->lock_list);
 				list_add_tail(&smb_lock->flist,
 					      &fp->lock_list);
 				spin_unlock(&work->conn->llist_lock);
-				list_add(&smb_lock->llist, &rollback_list);
 				ksmbd_debug(SMB, "successful in taking lock\n");
 			} else {
 				goto out;
@@ -7017,7 +7191,10 @@
 	ksmbd_debug(SMB, "successful in taking lock\n");
 	rsp->hdr.Status = STATUS_SUCCESS;
 	rsp->Reserved = 0;
-	inc_rfc1001_len(rsp, 4);
+	err = ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_lock_rsp));
+	if (err)
+		goto out;
+
 	ksmbd_fd_put(work, fp);
 	return 0;
 
@@ -7036,7 +7213,7 @@
 		rlock->fl_start = smb_lock->start;
 		rlock->fl_end = smb_lock->end;
 
-		rc = vfs_lock_file(filp, 0, rlock, NULL);
+		rc = vfs_lock_file(filp, F_SETLK, rlock, NULL);
 		if (rc)
 			pr_err("rollback unlock fail : %d\n", rc);
 
@@ -7088,8 +7265,8 @@
 
 	ci_rsp = (struct copychunk_ioctl_rsp *)&rsp->Buffer[0];
 
-	rsp->VolatileFileId = cpu_to_le64(volatile_id);
-	rsp->PersistentFileId = cpu_to_le64(persistent_id);
+	rsp->VolatileFileId = volatile_id;
+	rsp->PersistentFileId = persistent_id;
 	ci_rsp->ChunksWritten =
 		cpu_to_le32(ksmbd_server_side_copy_max_chunk_count());
 	ci_rsp->ChunkBytesWritten =
@@ -7210,15 +7387,10 @@
 	struct sockaddr_storage_rsp *sockaddr_storage;
 	unsigned int flags;
 	unsigned long long speed;
-	struct sockaddr_in6 *csin6 = (struct sockaddr_in6 *)&conn->peer_addr;
 
 	rtnl_lock();
 	for_each_netdev(&init_net, netdev) {
-		if (out_buf_len <
-		    nbytes + sizeof(struct network_interface_info_ioctl_rsp)) {
-			rtnl_unlock();
-			return -ENOSPC;
-		}
+		bool ipv4_set = false;
 
 		if (netdev->type == ARPHRD_LOOPBACK)
 			continue;
@@ -7226,12 +7398,20 @@
 		flags = dev_get_flags(netdev);
 		if (!(flags & IFF_RUNNING))
 			continue;
+ipv6_retry:
+		if (out_buf_len <
+		    nbytes + sizeof(struct network_interface_info_ioctl_rsp)) {
+			rtnl_unlock();
+			return -ENOSPC;
+		}
 
 		nii_rsp = (struct network_interface_info_ioctl_rsp *)
 				&rsp->Buffer[nbytes];
 		nii_rsp->IfIndex = cpu_to_le32(netdev->ifindex);
 
 		nii_rsp->Capability = 0;
+		if (netdev->real_num_tx_queues > 1)
+			nii_rsp->Capability |= cpu_to_le32(RSS_CAPABLE);
 		if (ksmbd_rdma_capable_netdev(netdev))
 			nii_rsp->Capability |= cpu_to_le32(RDMA_CAPABLE);
 
@@ -7256,8 +7436,7 @@
 					nii_rsp->SockAddr_Storage;
 		memset(sockaddr_storage, 0, 128);
 
-		if (conn->peer_addr.ss_family == PF_INET ||
-		    ipv6_addr_v4mapped(&csin6->sin6_addr)) {
+		if (!ipv4_set) {
 			struct in_device *idev;
 
 			sockaddr_storage->Family = cpu_to_le16(INTERNETWORK);
@@ -7268,6 +7447,9 @@
 				continue;
 			sockaddr_storage->addr4.IPv4address =
 						idev_ipv4_address(idev);
+			nbytes += sizeof(struct network_interface_info_ioctl_rsp);
+			ipv4_set = true;
+			goto ipv6_retry;
 		} else {
 			struct inet6_dev *idev6;
 			struct inet6_ifaddr *ifa;
@@ -7289,9 +7471,8 @@
 				break;
 			}
 			sockaddr_storage->addr6.ScopeId = 0;
+			nbytes += sizeof(struct network_interface_info_ioctl_rsp);
 		}
-
-		nbytes += sizeof(struct network_interface_info_ioctl_rsp);
 	}
 	rtnl_unlock();
 
@@ -7299,8 +7480,8 @@
 	if (nii_rsp)
 		nii_rsp->Next = 0;
 
-	rsp->PersistentFileId = cpu_to_le64(SMB2_NO_FID);
-	rsp->VolatileFileId = cpu_to_le64(SMB2_NO_FID);
+	rsp->PersistentFileId = SMB2_NO_FID;
+	rsp->VolatileFileId = SMB2_NO_FID;
 	return nbytes;
 }
 
@@ -7312,7 +7493,7 @@
 	int ret = 0;
 	int dialect;
 
-	if (in_buf_len < sizeof(struct validate_negotiate_info_req) +
+	if (in_buf_len < offsetof(struct validate_negotiate_info_req, Dialects) +
 			le16_to_cpu(neg_req->DialectCount) * sizeof(__le16))
 		return -EINVAL;
 
@@ -7359,13 +7540,16 @@
 	if (in_count == 0)
 		return -EINVAL;
 
+	start = le64_to_cpu(qar_req->file_offset);
+	length = le64_to_cpu(qar_req->length);
+
+	if (start < 0 || length < 0)
+		return -EINVAL;
+
 	fp = ksmbd_lookup_fd_fast(work, id);
 	if (!fp)
 		return -ENOENT;
 
-	start = le64_to_cpu(qar_req->file_offset);
-	length = le64_to_cpu(qar_req->length);
-
 	ret = ksmbd_vfs_fqar_lseek(fp, start, length,
 				   qar_rsp, in_count, out_count);
 	if (ret && ret != -E2BIG)
@@ -7381,7 +7565,7 @@
 				 struct smb2_ioctl_rsp *rsp)
 {
 	struct ksmbd_rpc_command *rpc_resp;
-	char *data_buf = (char *)&req->Buffer[0];
+	char *data_buf = (char *)req + le32_to_cpu(req->InputOffset);
 	int nbytes = 0;
 
 	rpc_resp = ksmbd_rpc_ioctl(work->sess, id, data_buf,
@@ -7451,7 +7635,8 @@
 
 		da.attr = le32_to_cpu(fp->f_ci->m_fattr);
 		ret = ksmbd_vfs_set_dos_attrib_xattr(user_ns,
-						     fp->filp->f_path.dentry, &da);
+						     &fp->filp->f_path,
+						     &da, true);
 		if (ret)
 			fp->f_ci->m_fattr = old_fattr;
 	}
@@ -7467,9 +7652,7 @@
 {
 	struct ksmbd_file *fp;
 
-	fp = ksmbd_lookup_fd_slow(work,
-				  le64_to_cpu(req->VolatileFileId),
-				  le64_to_cpu(req->PersistentFileId));
+	fp = ksmbd_lookup_fd_slow(work, req->VolatileFileId, req->PersistentFileId);
 	if (!fp)
 		return -ENOENT;
 
@@ -7490,34 +7673,36 @@
 int smb2_ioctl(struct ksmbd_work *work)
 {
 	struct smb2_ioctl_req *req;
-	struct smb2_ioctl_rsp *rsp, *rsp_org;
+	struct smb2_ioctl_rsp *rsp;
 	unsigned int cnt_code, nbytes = 0, out_buf_len, in_buf_len;
 	u64 id = KSMBD_NO_FID;
 	struct ksmbd_conn *conn = work->conn;
 	int ret = 0;
+	char *buffer;
 
-	rsp_org = work->response_buf;
 	if (work->next_smb2_rcv_hdr_off) {
 		req = ksmbd_req_buf_next(work);
 		rsp = ksmbd_resp_buf_next(work);
-		if (!has_file_id(le64_to_cpu(req->VolatileFileId))) {
+		if (!has_file_id(req->VolatileFileId)) {
 			ksmbd_debug(SMB, "Compound request set FID = %llu\n",
 				    work->compound_fid);
 			id = work->compound_fid;
 		}
 	} else {
-		req = work->request_buf;
-		rsp = work->response_buf;
+		req = smb2_get_msg(work->request_buf);
+		rsp = smb2_get_msg(work->response_buf);
 	}
 
 	if (!has_file_id(id))
-		id = le64_to_cpu(req->VolatileFileId);
+		id = req->VolatileFileId;
 
 	if (req->Flags != cpu_to_le32(SMB2_0_IOCTL_IS_FSCTL)) {
 		rsp->hdr.Status = STATUS_NOT_SUPPORTED;
 		goto out;
 	}
 
+	buffer = (char *)req + le32_to_cpu(req->InputOffset);
+
 	cnt_code = le32_to_cpu(req->CntCode);
 	ret = smb2_calc_max_out_buf_len(work, 48,
 					le32_to_cpu(req->MaxOutputResponse));
@@ -7563,22 +7748,27 @@
 			goto out;
 		}
 
-		if (in_buf_len < sizeof(struct validate_negotiate_info_req))
-			return -EINVAL;
+		if (in_buf_len < offsetof(struct validate_negotiate_info_req,
+					  Dialects)) {
+			ret = -EINVAL;
+			goto out;
+		}
 
-		if (out_buf_len < sizeof(struct validate_negotiate_info_rsp))
-			return -EINVAL;
+		if (out_buf_len < sizeof(struct validate_negotiate_info_rsp)) {
+			ret = -EINVAL;
+			goto out;
+		}
 
 		ret = fsctl_validate_negotiate_info(conn,
-			(struct validate_negotiate_info_req *)&req->Buffer[0],
+			(struct validate_negotiate_info_req *)buffer,
 			(struct validate_negotiate_info_rsp *)&rsp->Buffer[0],
 			in_buf_len);
 		if (ret < 0)
 			goto out;
 
 		nbytes = sizeof(struct validate_negotiate_info_rsp);
-		rsp->PersistentFileId = cpu_to_le64(SMB2_NO_FID);
-		rsp->VolatileFileId = cpu_to_le64(SMB2_NO_FID);
+		rsp->PersistentFileId = SMB2_NO_FID;
+		rsp->VolatileFileId = SMB2_NO_FID;
 		break;
 	case FSCTL_QUERY_NETWORK_INTERFACE_INFO:
 		ret = fsctl_query_iface_info_ioctl(conn, rsp, out_buf_len);
@@ -7623,11 +7813,11 @@
 		rsp->VolatileFileId = req->VolatileFileId;
 		rsp->PersistentFileId = req->PersistentFileId;
 		fsctl_copychunk(work,
-				(struct copychunk_ioctl_req *)&req->Buffer[0],
+				(struct copychunk_ioctl_req *)buffer,
 				le32_to_cpu(req->CntCode),
 				le32_to_cpu(req->InputCount),
-				le64_to_cpu(req->VolatileFileId),
-				le64_to_cpu(req->PersistentFileId),
+				req->VolatileFileId,
+				req->PersistentFileId,
 				rsp);
 		break;
 	case FSCTL_SET_SPARSE:
@@ -7636,8 +7826,7 @@
 			goto out;
 		}
 
-		ret = fsctl_set_sparse(work, id,
-				       (struct file_sparse *)&req->Buffer[0]);
+		ret = fsctl_set_sparse(work, id, (struct file_sparse *)buffer);
 		if (ret < 0)
 			goto out;
 		break;
@@ -7645,7 +7834,7 @@
 	{
 		struct file_zero_data_information *zero_data;
 		struct ksmbd_file *fp;
-		loff_t off, len;
+		loff_t off, len, bfz;
 
 		if (!test_tree_conn_flag(work->tcon, KSMBD_TREE_CONN_FLAG_WRITABLE)) {
 			ksmbd_debug(SMB,
@@ -7660,21 +7849,28 @@
 		}
 
 		zero_data =
-			(struct file_zero_data_information *)&req->Buffer[0];
+			(struct file_zero_data_information *)buffer;
 
-		fp = ksmbd_lookup_fd_fast(work, id);
-		if (!fp) {
-			ret = -ENOENT;
+		off = le64_to_cpu(zero_data->FileOffset);
+		bfz = le64_to_cpu(zero_data->BeyondFinalZero);
+		if (off < 0 || bfz < 0 || off > bfz) {
+			ret = -EINVAL;
 			goto out;
 		}
 
-		off = le64_to_cpu(zero_data->FileOffset);
-		len = le64_to_cpu(zero_data->BeyondFinalZero) - off;
+		len = bfz - off;
+		if (len) {
+			fp = ksmbd_lookup_fd_fast(work, id);
+			if (!fp) {
+				ret = -ENOENT;
+				goto out;
+			}
 
-		ret = ksmbd_vfs_zero_data(work, fp, off, len);
-		ksmbd_fd_put(work, fp);
-		if (ret < 0)
-			goto out;
+			ret = ksmbd_vfs_zero_data(work, fp, off, len);
+			ksmbd_fd_put(work, fp);
+			if (ret < 0)
+				goto out;
+		}
 		break;
 	}
 	case FSCTL_QUERY_ALLOCATED_RANGES:
@@ -7684,7 +7880,7 @@
 		}
 
 		ret = fsctl_query_allocated_ranges(work, id,
-			(struct file_allocated_range_buffer *)&req->Buffer[0],
+			(struct file_allocated_range_buffer *)buffer,
 			(struct file_allocated_range_buffer *)&rsp->Buffer[0],
 			out_buf_len /
 			sizeof(struct file_allocated_range_buffer), &nbytes);
@@ -7728,7 +7924,7 @@
 			goto out;
 		}
 
-		dup_ext = (struct duplicate_extents_to_file *)&req->Buffer[0];
+		dup_ext = (struct duplicate_extents_to_file *)buffer;
 
 		fp_in = ksmbd_lookup_fd_slow(work, dup_ext->VolatileFileHandle,
 					     dup_ext->PersistentFileHandle);
@@ -7748,14 +7944,24 @@
 		src_off = le64_to_cpu(dup_ext->SourceFileOffset);
 		dst_off = le64_to_cpu(dup_ext->TargetFileOffset);
 		length = le64_to_cpu(dup_ext->ByteCount);
-		cloned = vfs_clone_file_range(fp_in->filp, src_off, fp_out->filp,
-					      dst_off, length, 0);
+		/*
+		 * XXX: It is not clear if FSCTL_DUPLICATE_EXTENTS_TO_FILE
+		 * should fall back to vfs_copy_file_range().  This could be
+		 * beneficial when re-exporting nfs/smb mount, but note that
+		 * this can result in partial copy that returns an error status.
+		 * If/when FSCTL_DUPLICATE_EXTENTS_TO_FILE_EX is implemented,
+		 * fall back to vfs_copy_file_range(), should be avoided when
+		 * the flag DUPLICATE_EXTENTS_DATA_EX_SOURCE_ATOMIC is set.
+		 */
+		cloned = vfs_clone_file_range(fp_in->filp, src_off,
+					      fp_out->filp, dst_off, length, 0);
 		if (cloned == -EXDEV || cloned == -EOPNOTSUPP) {
 			ret = -EOPNOTSUPP;
 			goto dup_ext_out;
 		} else if (cloned != length) {
 			cloned = vfs_copy_file_range(fp_in->filp, src_off,
-						     fp_out->filp, dst_off, length, 0);
+						     fp_out->filp, dst_off,
+						     length, 0);
 			if (cloned != length) {
 				if (cloned < 0)
 					ret = cloned;
@@ -7787,9 +7993,9 @@
 	rsp->Reserved = cpu_to_le16(0);
 	rsp->Flags = cpu_to_le32(0);
 	rsp->Reserved2 = cpu_to_le32(0);
-	inc_rfc1001_len(rsp_org, 48 + nbytes);
-
-	return 0;
+	ret = ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_ioctl_rsp) + nbytes);
+	if (!ret)
+		return ret;
 
 out:
 	if (ret == -EACCES)
@@ -7814,8 +8020,8 @@
  */
 static void smb20_oplock_break_ack(struct ksmbd_work *work)
 {
-	struct smb2_oplock_break *req = work->request_buf;
-	struct smb2_oplock_break *rsp = work->response_buf;
+	struct smb2_oplock_break *req;
+	struct smb2_oplock_break *rsp;
 	struct ksmbd_file *fp;
 	struct oplock_info *opinfo = NULL;
 	__le32 err = 0;
@@ -7824,8 +8030,10 @@
 	char req_oplevel = 0, rsp_oplevel = 0;
 	unsigned int oplock_change_type;
 
-	volatile_id = le64_to_cpu(req->VolatileFid);
-	persistent_id = le64_to_cpu(req->PersistentFid);
+	WORK_BUFFERS(work, req, rsp);
+
+	volatile_id = req->VolatileFid;
+	persistent_id = req->PersistentFid;
 	req_oplevel = req->OplockLevel;
 	ksmbd_debug(OPLOCK, "v_id %llu, p_id %llu request oplock level %d\n",
 		    volatile_id, persistent_id, req_oplevel);
@@ -7911,19 +8119,20 @@
 		goto err_out;
 	}
 
-	opinfo_put(opinfo);
-	ksmbd_fd_put(work, fp);
 	opinfo->op_state = OPLOCK_STATE_NONE;
 	wake_up_interruptible_all(&opinfo->oplock_q);
+	opinfo_put(opinfo);
+	ksmbd_fd_put(work, fp);
 
 	rsp->StructureSize = cpu_to_le16(24);
 	rsp->OplockLevel = rsp_oplevel;
 	rsp->Reserved = 0;
 	rsp->Reserved2 = 0;
-	rsp->VolatileFid = cpu_to_le64(volatile_id);
-	rsp->PersistentFid = cpu_to_le64(persistent_id);
-	inc_rfc1001_len(rsp, 24);
-	return;
+	rsp->VolatileFid = volatile_id;
+	rsp->PersistentFid = persistent_id;
+	ret = ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_oplock_break));
+	if (!ret)
+		return;
 
 err_out:
 	opinfo->op_state = OPLOCK_STATE_NONE;
@@ -7958,8 +8167,8 @@
 static void smb21_lease_break_ack(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_lease_ack *req = work->request_buf;
-	struct smb2_lease_ack *rsp = work->response_buf;
+	struct smb2_lease_ack *req;
+	struct smb2_lease_ack *rsp;
 	struct oplock_info *opinfo;
 	__le32 err = 0;
 	int ret = 0;
@@ -7967,6 +8176,8 @@
 	__le32 lease_state;
 	struct lease *lease;
 
+	WORK_BUFFERS(work, req, rsp);
+
 	ksmbd_debug(OPLOCK, "smb21 lease break, lease state(0x%x)\n",
 		    le32_to_cpu(req->LeaseState));
 	opinfo = lookup_lease_in_table(conn, req->LeaseKey);
@@ -8053,6 +8264,11 @@
 			    le32_to_cpu(req->LeaseState));
 	}
 
+	if (ret < 0) {
+		rsp->hdr.Status = err;
+		goto err_out;
+	}
+
 	lease_state = lease->state;
 	opinfo->op_state = OPLOCK_STATE_NONE;
 	wake_up_interruptible_all(&opinfo->oplock_q);
@@ -8060,22 +8276,17 @@
 	wake_up_interruptible_all(&opinfo->oplock_brk);
 	opinfo_put(opinfo);
 
-	if (ret < 0) {
-		rsp->hdr.Status = err;
-		goto err_out;
-	}
-
 	rsp->StructureSize = cpu_to_le16(36);
 	rsp->Reserved = 0;
 	rsp->Flags = 0;
 	memcpy(rsp->LeaseKey, req->LeaseKey, 16);
 	rsp->LeaseState = lease_state;
 	rsp->LeaseDuration = 0;
-	inc_rfc1001_len(rsp, 36);
-	return;
+	ret = ksmbd_iov_pin_rsp(work, rsp, sizeof(struct smb2_lease_ack));
+	if (!ret)
+		return;
 
 err_out:
-	opinfo->op_state = OPLOCK_STATE_NONE;
 	wake_up_interruptible_all(&opinfo->oplock_q);
 	atomic_dec(&opinfo->breaking_cnt);
 	wake_up_interruptible_all(&opinfo->oplock_brk);
@@ -8092,8 +8303,10 @@
  */
 int smb2_oplock_break(struct ksmbd_work *work)
 {
-	struct smb2_oplock_break *req = work->request_buf;
-	struct smb2_oplock_break *rsp = work->response_buf;
+	struct smb2_oplock_break *req;
+	struct smb2_oplock_break *rsp;
+
+	WORK_BUFFERS(work, req, rsp);
 
 	switch (le16_to_cpu(req->StructureSize)) {
 	case OP_BREAK_STRUCT_SIZE_20:
@@ -8145,7 +8358,7 @@
  */
 bool smb2_is_sign_req(struct ksmbd_work *work, unsigned int command)
 {
-	struct smb2_hdr *rcv_hdr2 = work->request_buf;
+	struct smb2_hdr *rcv_hdr2 = smb2_get_msg(work->request_buf);
 
 	if ((rcv_hdr2->Flags & SMB2_FLAGS_SIGNED) &&
 	    command != SMB2_NEGOTIATE_HE &&
@@ -8164,22 +8377,22 @@
  */
 int smb2_check_sign_req(struct ksmbd_work *work)
 {
-	struct smb2_hdr *hdr, *hdr_org;
+	struct smb2_hdr *hdr;
 	char signature_req[SMB2_SIGNATURE_SIZE];
 	char signature[SMB2_HMACSHA256_SIZE];
 	struct kvec iov[1];
 	size_t len;
 
-	hdr_org = hdr = work->request_buf;
+	hdr = smb2_get_msg(work->request_buf);
 	if (work->next_smb2_rcv_hdr_off)
 		hdr = ksmbd_req_buf_next(work);
 
 	if (!hdr->NextCommand && !work->next_smb2_rcv_hdr_off)
-		len = be32_to_cpu(hdr_org->smb2_buf_length);
+		len = get_rfc1002_len(work->request_buf);
 	else if (hdr->NextCommand)
 		len = le32_to_cpu(hdr->NextCommand);
 	else
-		len = be32_to_cpu(hdr_org->smb2_buf_length) -
+		len = get_rfc1002_len(work->request_buf) -
 			work->next_smb2_rcv_hdr_off;
 
 	memcpy(signature_req, hdr->Signature, SMB2_SIGNATURE_SIZE);
@@ -8207,43 +8420,20 @@
  */
 void smb2_set_sign_rsp(struct ksmbd_work *work)
 {
-	struct smb2_hdr *hdr, *hdr_org;
-	struct smb2_hdr *req_hdr;
+	struct smb2_hdr *hdr;
 	char signature[SMB2_HMACSHA256_SIZE];
-	struct kvec iov[2];
-	size_t len;
+	struct kvec *iov;
 	int n_vec = 1;
 
-	hdr_org = hdr = work->response_buf;
-	if (work->next_smb2_rsp_hdr_off)
-		hdr = ksmbd_resp_buf_next(work);
-
-	req_hdr = ksmbd_req_buf_next(work);
-
-	if (!work->next_smb2_rsp_hdr_off) {
-		len = get_rfc1002_len(hdr_org);
-		if (req_hdr->NextCommand)
-			len = ALIGN(len, 8);
-	} else {
-		len = get_rfc1002_len(hdr_org) - work->next_smb2_rsp_hdr_off;
-		len = ALIGN(len, 8);
-	}
-
-	if (req_hdr->NextCommand)
-		hdr->NextCommand = cpu_to_le32(len);
-
+	hdr = ksmbd_resp_buf_curr(work);
 	hdr->Flags |= SMB2_FLAGS_SIGNED;
 	memset(hdr->Signature, 0, SMB2_SIGNATURE_SIZE);
 
-	iov[0].iov_base = (char *)&hdr->ProtocolId;
-	iov[0].iov_len = len;
-
-	if (work->aux_payload_sz) {
-		iov[0].iov_len -= work->aux_payload_sz;
-
-		iov[1].iov_base = work->aux_payload_buf;
-		iov[1].iov_len = work->aux_payload_sz;
+	if (hdr->Command == SMB2_READ) {
+		iov = &work->iov[work->iov_idx - 1];
 		n_vec++;
+	} else {
+		iov = &work->iov[work->iov_idx];
 	}
 
 	if (!ksmbd_sign_smb2_pdu(work->conn, work->sess->sess_key, iov, n_vec,
@@ -8261,31 +8451,32 @@
 {
 	struct ksmbd_conn *conn = work->conn;
 	char *signing_key;
-	struct smb2_hdr *hdr, *hdr_org;
+	struct smb2_hdr *hdr;
 	struct channel *chann;
 	char signature_req[SMB2_SIGNATURE_SIZE];
 	char signature[SMB2_CMACAES_SIZE];
 	struct kvec iov[1];
 	size_t len;
 
-	hdr_org = hdr = work->request_buf;
+	hdr = smb2_get_msg(work->request_buf);
 	if (work->next_smb2_rcv_hdr_off)
 		hdr = ksmbd_req_buf_next(work);
 
 	if (!hdr->NextCommand && !work->next_smb2_rcv_hdr_off)
-		len = be32_to_cpu(hdr_org->smb2_buf_length);
+		len = get_rfc1002_len(work->request_buf);
 	else if (hdr->NextCommand)
 		len = le32_to_cpu(hdr->NextCommand);
 	else
-		len = be32_to_cpu(hdr_org->smb2_buf_length) -
+		len = get_rfc1002_len(work->request_buf) -
 			work->next_smb2_rcv_hdr_off;
 
 	if (le16_to_cpu(hdr->Command) == SMB2_SESSION_SETUP_HE) {
 		signing_key = work->sess->smb3signingkey;
 	} else {
 		chann = lookup_chann_list(work->sess, conn);
-		if (!chann)
+		if (!chann) {
 			return 0;
+		}
 		signing_key = chann->smb3signingkey;
 	}
 
@@ -8318,58 +8509,41 @@
 void smb3_set_sign_rsp(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_hdr *req_hdr;
-	struct smb2_hdr *hdr, *hdr_org;
+	struct smb2_hdr *hdr;
 	struct channel *chann;
 	char signature[SMB2_CMACAES_SIZE];
-	struct kvec iov[2];
+	struct kvec *iov;
 	int n_vec = 1;
-	size_t len;
 	char *signing_key;
 
-	hdr_org = hdr = work->response_buf;
-	if (work->next_smb2_rsp_hdr_off)
-		hdr = ksmbd_resp_buf_next(work);
-
-	req_hdr = ksmbd_req_buf_next(work);
-
-	if (!work->next_smb2_rsp_hdr_off) {
-		len = get_rfc1002_len(hdr_org);
-		if (req_hdr->NextCommand)
-			len = ALIGN(len, 8);
-	} else {
-		len = get_rfc1002_len(hdr_org) - work->next_smb2_rsp_hdr_off;
-		len = ALIGN(len, 8);
-	}
+	hdr = ksmbd_resp_buf_curr(work);
 
 	if (conn->binding == false &&
 	    le16_to_cpu(hdr->Command) == SMB2_SESSION_SETUP_HE) {
 		signing_key = work->sess->smb3signingkey;
 	} else {
 		chann = lookup_chann_list(work->sess, work->conn);
-		if (!chann)
+		if (!chann) {
 			return;
+		}
 		signing_key = chann->smb3signingkey;
 	}
 
 	if (!signing_key)
 		return;
 
-	if (req_hdr->NextCommand)
-		hdr->NextCommand = cpu_to_le32(len);
-
 	hdr->Flags |= SMB2_FLAGS_SIGNED;
 	memset(hdr->Signature, 0, SMB2_SIGNATURE_SIZE);
-	iov[0].iov_base = (char *)&hdr->ProtocolId;
-	iov[0].iov_len = len;
-	if (work->aux_payload_sz) {
-		iov[0].iov_len -= work->aux_payload_sz;
-		iov[1].iov_base = work->aux_payload_buf;
-		iov[1].iov_len = work->aux_payload_sz;
+
+	if (hdr->Command == SMB2_READ) {
+		iov = &work->iov[work->iov_idx - 1];
 		n_vec++;
+	} else {
+		iov = &work->iov[work->iov_idx];
 	}
 
-	if (!ksmbd_sign_smb3_pdu(conn, signing_key, iov, n_vec, signature))
+	if (!ksmbd_sign_smb3_pdu(conn, signing_key, iov, n_vec,
+				 signature))
 		memcpy(hdr->Signature, signature, SMB2_SIGNATURE_SIZE);
 }
 
@@ -8391,7 +8565,7 @@
 
 	if (le16_to_cpu(req->Command) == SMB2_NEGOTIATE_HE &&
 	    conn->preauth_info)
-		ksmbd_gen_preauth_integrity_hash(conn, (char *)rsp,
+		ksmbd_gen_preauth_integrity_hash(conn, work->response_buf,
 						 conn->preauth_info->Preauth_HashValue);
 
 	if (le16_to_cpu(rsp->Command) == SMB2_SESSION_SETUP_HE && sess) {
@@ -8409,18 +8583,18 @@
 			if (!hash_value)
 				return;
 		}
-		ksmbd_gen_preauth_integrity_hash(conn, (char *)rsp,
+		ksmbd_gen_preauth_integrity_hash(conn, work->response_buf,
 						 hash_value);
 	}
 }
 
-static void fill_transform_hdr(struct smb2_transform_hdr *tr_hdr, char *old_buf,
-			       __le16 cipher_type)
+static void fill_transform_hdr(void *tr_buf, char *old_buf, __le16 cipher_type)
 {
-	struct smb2_hdr *hdr = (struct smb2_hdr *)old_buf;
+	struct smb2_transform_hdr *tr_hdr = tr_buf + 4;
+	struct smb2_hdr *hdr = smb2_get_msg(old_buf);
 	unsigned int orig_len = get_rfc1002_len(old_buf);
 
-	memset(tr_hdr, 0, sizeof(struct smb2_transform_hdr));
+	/* tr_buf must be cleared by the caller */
 	tr_hdr->ProtocolId = SMB2_TRANSFORM_PROTO_NUM;
 	tr_hdr->OriginalMessageSize = cpu_to_le32(orig_len);
 	tr_hdr->Flags = cpu_to_le16(0x01);
@@ -8430,76 +8604,49 @@
 	else
 		get_random_bytes(&tr_hdr->Nonce, SMB3_AES_CCM_NONCE);
 	memcpy(&tr_hdr->SessionId, &hdr->SessionId, 8);
-	inc_rfc1001_len(tr_hdr, sizeof(struct smb2_transform_hdr) - 4);
-	inc_rfc1001_len(tr_hdr, orig_len);
+	inc_rfc1001_len(tr_buf, sizeof(struct smb2_transform_hdr));
+	inc_rfc1001_len(tr_buf, orig_len);
 }
 
 int smb3_encrypt_resp(struct ksmbd_work *work)
 {
-	char *buf = work->response_buf;
-	struct smb2_transform_hdr *tr_hdr;
-	struct kvec iov[3];
+	struct kvec *iov = work->iov;
 	int rc = -ENOMEM;
-	int buf_size = 0, rq_nvec = 2 + (work->aux_payload_sz ? 1 : 0);
+	void *tr_buf;
 
-	if (ARRAY_SIZE(iov) < rq_nvec)
-		return -ENOMEM;
-
-	tr_hdr = kzalloc(sizeof(struct smb2_transform_hdr), GFP_KERNEL);
-	if (!tr_hdr)
+	tr_buf = kzalloc(sizeof(struct smb2_transform_hdr) + 4, GFP_KERNEL);
+	if (!tr_buf)
 		return rc;
 
 	/* fill transform header */
-	fill_transform_hdr(tr_hdr, buf, work->conn->cipher_type);
+	fill_transform_hdr(tr_buf, work->response_buf, work->conn->cipher_type);
 
-	iov[0].iov_base = tr_hdr;
-	iov[0].iov_len = sizeof(struct smb2_transform_hdr);
-	buf_size += iov[0].iov_len - 4;
+	iov[0].iov_base = tr_buf;
+	iov[0].iov_len = sizeof(struct smb2_transform_hdr) + 4;
+	work->tr_buf = tr_buf;
 
-	iov[1].iov_base = buf + 4;
-	iov[1].iov_len = get_rfc1002_len(buf);
-	if (work->aux_payload_sz) {
-		iov[1].iov_len = work->resp_hdr_sz - 4;
-
-		iov[2].iov_base = work->aux_payload_buf;
-		iov[2].iov_len = work->aux_payload_sz;
-		buf_size += iov[2].iov_len;
-	}
-	buf_size += iov[1].iov_len;
-	work->resp_hdr_sz = iov[1].iov_len;
-
-	rc = ksmbd_crypt_message(work->conn, iov, rq_nvec, 1);
-	if (rc)
-		return rc;
-
-	memmove(buf, iov[1].iov_base, iov[1].iov_len);
-	tr_hdr->smb2_buf_length = cpu_to_be32(buf_size);
-	work->tr_buf = tr_hdr;
-
-	return rc;
+	return ksmbd_crypt_message(work, iov, work->iov_idx + 1, 1);
 }
 
 bool smb3_is_transform_hdr(void *buf)
 {
-	struct smb2_transform_hdr *trhdr = buf;
+	struct smb2_transform_hdr *trhdr = smb2_get_msg(buf);
 
 	return trhdr->ProtocolId == SMB2_TRANSFORM_PROTO_NUM;
 }
 
 int smb3_decrypt_req(struct ksmbd_work *work)
 {
-	struct ksmbd_conn *conn = work->conn;
 	struct ksmbd_session *sess;
 	char *buf = work->request_buf;
-	struct smb2_hdr *hdr;
 	unsigned int pdu_length = get_rfc1002_len(buf);
 	struct kvec iov[2];
-	int buf_data_size = pdu_length + 4 -
-		sizeof(struct smb2_transform_hdr);
-	struct smb2_transform_hdr *tr_hdr = (struct smb2_transform_hdr *)buf;
+	int buf_data_size = pdu_length - sizeof(struct smb2_transform_hdr);
+	struct smb2_transform_hdr *tr_hdr = smb2_get_msg(buf);
 	int rc = 0;
 
-	if (buf_data_size < sizeof(struct smb2_hdr)) {
+	if (pdu_length < sizeof(struct smb2_transform_hdr) ||
+	    buf_data_size < sizeof(struct smb2_hdr)) {
 		pr_err("Transform message is too small (%u)\n",
 		       pdu_length);
 		return -ECONNABORTED;
@@ -8510,24 +8657,24 @@
 		return -ECONNABORTED;
 	}
 
-	sess = ksmbd_session_lookup_all(conn, le64_to_cpu(tr_hdr->SessionId));
+	sess = ksmbd_session_lookup_all(work->conn, le64_to_cpu(tr_hdr->SessionId));
 	if (!sess) {
 		pr_err("invalid session id(%llx) in transform header\n",
 		       le64_to_cpu(tr_hdr->SessionId));
 		return -ECONNABORTED;
 	}
+	ksmbd_user_session_put(sess);
 
 	iov[0].iov_base = buf;
-	iov[0].iov_len = sizeof(struct smb2_transform_hdr);
-	iov[1].iov_base = buf + sizeof(struct smb2_transform_hdr);
+	iov[0].iov_len = sizeof(struct smb2_transform_hdr) + 4;
+	iov[1].iov_base = buf + sizeof(struct smb2_transform_hdr) + 4;
 	iov[1].iov_len = buf_data_size;
-	rc = ksmbd_crypt_message(conn, iov, 2, 0);
+	rc = ksmbd_crypt_message(work, iov, 2, 0);
 	if (rc)
 		return rc;
 
 	memmove(buf + 4, iov[1].iov_base, buf_data_size);
-	hdr = (struct smb2_hdr *)buf;
-	hdr->smb2_buf_length = cpu_to_be32(buf_data_size);
+	*(__be32 *)buf = cpu_to_be32(buf_data_size);
 
 	return rc;
 }
@@ -8535,7 +8682,8 @@
 bool smb3_11_final_sess_setup_resp(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
-	struct smb2_hdr *rsp = work->response_buf;
+	struct ksmbd_session *sess = work->sess;
+	struct smb2_hdr *rsp = smb2_get_msg(work->response_buf);
 
 	if (conn->dialect < SMB30_PROT_ID)
 		return false;
@@ -8544,6 +8692,7 @@
 		rsp = ksmbd_resp_buf_next(work);
 
 	if (le16_to_cpu(rsp->Command) == SMB2_SESSION_SETUP_HE &&
+	    sess->user && !user_guest(sess->user) &&
 	    rsp->Status == STATUS_SUCCESS)
 		return true;
 	return false;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smb2pdu.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smb2pdu.h
@@ -109,12 +109,14 @@
 
 #define SMB2_PROTO_NUMBER cpu_to_le32(0x424d53fe) /* 'B''M''S' */
 #define SMB2_TRANSFORM_PROTO_NUM cpu_to_le32(0x424d53fd)
+#define SMB2_COMPRESSION_TRANSFORM_ID cpu_to_le32(0x424d53fc)
 
 #define SMB21_DEFAULT_IOSIZE	(1024 * 1024)
 #define SMB3_DEFAULT_IOSIZE	(4 * 1024 * 1024)
 #define SMB3_DEFAULT_TRANS_SIZE	(1024 * 1024)
-#define SMB3_MIN_IOSIZE	(64 * 1024)
-#define SMB3_MAX_IOSIZE	(8 * 1024 * 1024)
+#define SMB3_MIN_IOSIZE		(64 * 1024)
+#define SMB3_MAX_IOSIZE		(8 * 1024 * 1024)
+#define SMB3_MAX_MSGSIZE	(4 * 4096)
 
 /*
  * SMB2 Header Definition
@@ -130,11 +132,6 @@
 	cpu_to_le16(__SMB2_HEADER_STRUCTURE_SIZE)
 
 struct smb2_hdr {
-	__be32 smb2_buf_length;	/* big endian on wire */
-				/*
-				 * length is only two or three bytes - with
-				 * one or two byte type preceding it that MBZ
-				 */
 	__le32 ProtocolId;	/* 0xFE 'S' 'M' 'B' */
 	__le16 StructureSize;	/* 64 */
 	__le16 CreditCharge;	/* MBZ */
@@ -164,11 +161,6 @@
 #define SMB3_AES_GCM_NONCE 12
 
 struct smb2_transform_hdr {
-	__be32 smb2_buf_length; /* big endian on wire */
-	/*
-	 * length is only two or three bytes - with
-	 * one or two byte type preceding it that MBZ
-	 */
 	__le32 ProtocolId;      /* 0xFD 'S' 'M' 'B' */
 	__u8   Signature[16];
 	__u8   Nonce[16];
@@ -253,14 +245,14 @@
 	__u8			Preauth_HashValue[PREAUTH_HASHVALUE_SIZE];
 };
 
-/* offset is sizeof smb2_negotiate_rsp - 4 but rounded up to 8 bytes. */
+/* offset is sizeof smb2_negotiate_rsp but rounded up to 8 bytes. */
 #ifdef CONFIG_SMB_SERVER_KERBEROS5
-/* sizeof(struct smb2_negotiate_rsp) - 4 =
+/* sizeof(struct smb2_negotiate_rsp) =
  * header(64) + response(64) + GSS_LENGTH(96) + GSS_PADDING(0)
  */
 #define OFFSET_OF_NEG_CONTEXT	0xe0
 #else
-/* sizeof(struct smb2_negotiate_rsp) - 4 =
+/* sizeof(struct smb2_negotiate_rsp) =
  * header(64) + response(64) + GSS_LENGTH(74) + GSS_PADDING(6)
  */
 #define OFFSET_OF_NEG_CONTEXT	0xd0
@@ -375,6 +367,8 @@
 #define SMB2_SESSION_IN_PROGRESS	BIT(0)
 #define SMB2_SESSION_VALID		BIT(1)
 
+#define SMB2_SESSION_TIMEOUT		(10 * HZ)
+
 /* Flags */
 #define SMB2_SESSION_REQ_FLAG_BINDING		0x01
 #define SMB2_SESSION_REQ_FLAG_ENCRYPT_DATA	0x04
@@ -628,6 +622,8 @@
 	__u8 Buffer[0];
 } __packed;
 
+#define SMB2_SESSION_TIMEOUT		(10 * HZ)
+
 struct create_durable_req_v2 {
 	struct create_context ccontext;
 	__u8   Name[8];
@@ -643,8 +639,8 @@
 	union {
 		__u8  Reserved[16];
 		struct {
-			__le64 PersistentFileId;
-			__le64 VolatileFileId;
+			__u64 PersistentFileId;
+			__u64 VolatileFileId;
 		} Fid;
 	} Data;
 } __packed;
@@ -653,8 +649,8 @@
 	struct create_context ccontext;
 	__u8   Name[8];
 	struct {
-		__le64 PersistentFileId;
-		__le64 VolatileFileId;
+		__u64 PersistentFileId;
+		__u64 VolatileFileId;
 	} Fid;
 	__u8 CreateGuid[16];
 	__le32 Flags;
@@ -733,7 +729,8 @@
 	__le32 nlink;
 	__le32 reparse_tag;
 	__le32 mode;
-	u8 SidBuffer[40];
+	/* SidBuffer contain two sids(Domain sid(28), UNIX group sid(16)) */
+	u8 SidBuffer[44];
 } __packed;
 
 #define SMB2_LEASE_NONE_LE			cpu_to_le32(0x00)
@@ -742,23 +739,23 @@
 #define SMB2_LEASE_WRITE_CACHING_LE		cpu_to_le32(0x04)
 
 #define SMB2_LEASE_FLAG_BREAK_IN_PROGRESS_LE	cpu_to_le32(0x02)
+#define SMB2_LEASE_FLAG_PARENT_LEASE_KEY_SET_LE	cpu_to_le32(0x04)
+
+#define SMB2_LEASE_KEY_SIZE			16
 
 struct lease_context {
-	__le64 LeaseKeyLow;
-	__le64 LeaseKeyHigh;
+	__u8 LeaseKey[SMB2_LEASE_KEY_SIZE];
 	__le32 LeaseState;
 	__le32 LeaseFlags;
 	__le64 LeaseDuration;
 } __packed;
 
 struct lease_context_v2 {
-	__le64 LeaseKeyLow;
-	__le64 LeaseKeyHigh;
+	__u8 LeaseKey[SMB2_LEASE_KEY_SIZE];
 	__le32 LeaseState;
 	__le32 LeaseFlags;
 	__le64 LeaseDuration;
-	__le64 ParentLeaseKeyLow;
-	__le64 ParentLeaseKeyHigh;
+	__u8 ParentLeaseKey[SMB2_LEASE_KEY_SIZE];
 	__le16 Epoch;
 	__le16 Reserved;
 } __packed;
@@ -899,8 +896,8 @@
 	__le16 StructureSize; /* Must be 57 */
 	__le16 Reserved; /* offset from start of SMB2 header to write data */
 	__le32 CntCode;
-	__le64  PersistentFileId;
-	__le64  VolatileFileId;
+	__u64  PersistentFileId;
+	__u64  VolatileFileId;
 	__le32 InputOffset; /* Reserved MBZ */
 	__le32 InputCount;
 	__le32 MaxInputResponse;
@@ -917,8 +914,8 @@
 	__le16 StructureSize; /* Must be 49 */
 	__le16 Reserved; /* offset from start of SMB2 header to write data */
 	__le32 CntCode;
-	__le64  PersistentFileId;
-	__le64  VolatileFileId;
+	__u64  PersistentFileId;
+	__u64  VolatileFileId;
 	__le32 InputOffset; /* Reserved MBZ */
 	__le32 InputCount;
 	__le32 OutputOffset;
@@ -987,7 +984,7 @@
 } __packed;
 
 struct resume_key_ioctl_rsp {
-	__le64 ResumeKey[3];
+	__u64 ResumeKey[3];
 	__le32 ContextLength;
 	__u8 Context[4]; /* ignored, Windows sets to 4 bytes of zero */
 } __packed;
@@ -1099,8 +1096,8 @@
 	__le16 StructureSize; /* Must be 48 */
 	__le16 LockCount;
 	__le32 Reserved;
-	__le64  PersistentFileId;
-	__le64  VolatileFileId;
+	__u64  PersistentFileId;
+	__u64  VolatileFileId;
 	/* Followed by at least one */
 	struct smb2_lock_element locks[1];
 } __packed;
@@ -1135,8 +1132,8 @@
 	__u8   FileInformationClass;
 	__u8   Flags;
 	__le32 FileIndex;
-	__le64  PersistentFileId;
-	__le64  VolatileFileId;
+	__u64  PersistentFileId;
+	__u64  VolatileFileId;
 	__le16 FileNameOffset;
 	__le16 FileNameLength;
 	__le32 OutputBufferLength;
@@ -1182,8 +1179,8 @@
 	__le32 InputBufferLength;
 	__le32 AdditionalInformation;
 	__le32 Flags;
-	__le64  PersistentFileId;
-	__le64  VolatileFileId;
+	__u64  PersistentFileId;
+	__u64  VolatileFileId;
 	__u8   Buffer[1];
 } __packed;
 
@@ -1204,8 +1201,8 @@
 	__le16 BufferOffset;
 	__u16  Reserved;
 	__le32 AdditionalInformation;
-	__le64  PersistentFileId;
-	__le64  VolatileFileId;
+	__u64  PersistentFileId;
+	__u64  VolatileFileId;
 	__u8   Buffer[1];
 } __packed;
 
@@ -1566,7 +1563,7 @@
 	__u8   Flags;
 	__u8   EaNameLength;
 	__le16 EaValueLength;
-	char name[1];
+	char name[];
 	/* optionally followed by value */
 } __packed; /* level 15 Query */
 
@@ -1627,9 +1624,10 @@
 	__le32 HardLinks;
 	__le32 ReparseTag;
 	__le32 Mode;
-	u8 SidBuffer[40];
+	/* SidBuffer contain two sids (UNIX user sid(16), UNIX group sid(16)) */
+	u8 SidBuffer[32];
 	__le32 name_len;
-	u8 name[1];
+	u8 name[];
 	/*
 	 * var sized owner SID
 	 * var sized group SID
@@ -1647,6 +1645,7 @@
 void init_smb2_max_read_size(unsigned int sz);
 void init_smb2_max_write_size(unsigned int sz);
 void init_smb2_max_trans_size(unsigned int sz);
+void init_smb2_max_credits(unsigned int sz);
 
 bool is_smb2_neg_cmd(struct ksmbd_work *work);
 bool is_smb2_rsp(struct ksmbd_work *work);
@@ -1670,6 +1669,7 @@
 struct file_lock *smb_flock_init(struct file *f);
 int setup_async_work(struct ksmbd_work *work, void (*fn)(void **),
 		     void **arg);
+void release_async_work(struct ksmbd_work *work);
 void smb2_send_interim_resp(struct ksmbd_work *work, __le32 status);
 struct channel *lookup_chann_list(struct ksmbd_session *sess,
 				  struct ksmbd_conn *conn);
@@ -1679,6 +1679,7 @@
 int smb3_encrypt_resp(struct ksmbd_work *work);
 bool smb3_11_final_sess_setup_resp(struct ksmbd_work *work);
 int smb2_set_rsp_credits(struct ksmbd_work *work);
+bool smb3_encryption_negotiated(struct ksmbd_conn *conn);
 
 /* smb2 misc functions */
 int ksmbd_smb2_check_message(struct ksmbd_work *work);
@@ -1705,4 +1706,13 @@
 int smb2_oplock_break(struct ksmbd_work *work);
 int smb2_notify(struct ksmbd_work *ksmbd_work);
 
+/*
+ * Get the body of the smb2 message excluding the 4 byte rfc1002 headers
+ * from request/response buffer.
+ */
+static inline void *smb2_get_msg(void *buf)
+{
+	return buf + 4;
+}
+
 #endif	/* _SMB2PDU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smb_common.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smb_common.c
@@ -4,6 +4,8 @@
  *   Copyright (C) 2018 Namjae Jeon <linkinjeon@kernel.org>
  */
 
+#include <linux/user_namespace.h>
+
 #include "smb_common.h"
 #include "server.h"
 #include "misc.h"
@@ -132,7 +134,7 @@
  */
 int ksmbd_verify_smb_message(struct ksmbd_work *work)
 {
-	struct smb2_hdr *smb2_hdr = work->request_buf + work->next_smb2_rcv_hdr_off;
+	struct smb2_hdr *smb2_hdr = ksmbd_req_buf_next(work);
 	struct smb_hdr *hdr;
 
 	if (smb2_hdr->ProtocolId == SMB2_PROTO_NUMBER)
@@ -140,8 +142,10 @@
 
 	hdr = work->request_buf;
 	if (*(__le32 *)hdr->Protocol == SMB1_PROTO_NUMBER &&
-	    hdr->Command == SMB_COM_NEGOTIATE)
+	    hdr->Command == SMB_COM_NEGOTIATE) {
+		work->conn->outstanding_credits++;
 		return 0;
+	}
 
 	return -EINVAL;
 }
@@ -154,7 +158,23 @@
  */
 bool ksmbd_smb_request(struct ksmbd_conn *conn)
 {
-	return conn->request_buf[0] == 0;
+	__le32 *proto;
+
+	if (conn->request_buf[0] != 0)
+		return false;
+
+	proto = (__le32 *)smb2_get_msg(conn->request_buf);
+	if (*proto == SMB2_COMPRESSION_TRANSFORM_ID) {
+		pr_err_ratelimited("smb2 compression not support yet");
+		return false;
+	}
+
+	if (*proto != SMB1_PROTO_NUMBER &&
+	    *proto != SMB2_PROTO_NUMBER &&
+	    *proto != SMB2_TRANSFORM_PROTO_NUM)
+		return false;
+
+	return true;
 }
 
 static bool supported_protocol(int idx)
@@ -239,18 +259,18 @@
 static int ksmbd_negotiate_smb_dialect(void *buf)
 {
 	int smb_buf_length = get_rfc1002_len(buf);
-	__le32 proto = ((struct smb2_hdr *)buf)->ProtocolId;
+	__le32 proto = ((struct smb2_hdr *)smb2_get_msg(buf))->ProtocolId;
 
 	if (proto == SMB2_PROTO_NUMBER) {
 		struct smb2_negotiate_req *req;
 		int smb2_neg_size =
-			offsetof(struct smb2_negotiate_req, Dialects) - 4;
+			offsetof(struct smb2_negotiate_req, Dialects);
 
-		req = (struct smb2_negotiate_req *)buf;
+		req = (struct smb2_negotiate_req *)smb2_get_msg(buf);
 		if (smb2_neg_size > smb_buf_length)
 			goto err_out;
 
-		if (smb2_neg_size + le16_to_cpu(req->DialectCount) * sizeof(__le16) >
+		if (struct_size(req, Dialects, le16_to_cpu(req->DialectCount)) >
 		    smb_buf_length)
 			goto err_out;
 
@@ -279,20 +299,129 @@
 	return BAD_PROT_ID;
 }
 
-int ksmbd_init_smb_server(struct ksmbd_work *work)
+#define SMB_COM_NEGOTIATE_EX	0x0
+
+/**
+ * get_smb1_cmd_val() - get smb command value from smb header
+ * @work:	smb work containing smb header
+ *
+ * Return:      smb command value
+ */
+static u16 get_smb1_cmd_val(struct ksmbd_work *work)
 {
-	struct ksmbd_conn *conn = work->conn;
+	return SMB_COM_NEGOTIATE_EX;
+}
+
+/**
+ * init_smb1_rsp_hdr() - initialize smb negotiate response header
+ * @work:	smb work containing smb request
+ *
+ * Return:      0 on success, otherwise -EINVAL
+ */
+static int init_smb1_rsp_hdr(struct ksmbd_work *work)
+{
+	struct smb_hdr *rsp_hdr = (struct smb_hdr *)work->response_buf;
+	struct smb_hdr *rcv_hdr = (struct smb_hdr *)work->request_buf;
+
+	rsp_hdr->Command = SMB_COM_NEGOTIATE;
+	*(__le32 *)rsp_hdr->Protocol = SMB1_PROTO_NUMBER;
+	rsp_hdr->Flags = SMBFLG_RESPONSE;
+	rsp_hdr->Flags2 = SMBFLG2_UNICODE | SMBFLG2_ERR_STATUS |
+		SMBFLG2_EXT_SEC | SMBFLG2_IS_LONG_NAME;
+	rsp_hdr->Pid = rcv_hdr->Pid;
+	rsp_hdr->Mid = rcv_hdr->Mid;
+	return 0;
+}
+
+/**
+ * smb1_check_user_session() - check for valid session for a user
+ * @work:	smb work containing smb request buffer
+ *
+ * Return:      0 on success, otherwise error
+ */
+static int smb1_check_user_session(struct ksmbd_work *work)
+{
+	unsigned int cmd = work->conn->ops->get_cmd_val(work);
 
-	if (conn->need_neg == false)
+	if (cmd == SMB_COM_NEGOTIATE_EX)
 		return 0;
 
-	init_smb3_11_server(conn);
+	return -EINVAL;
+}
 
-	if (conn->ops->get_cmd_val(work) != SMB_COM_NEGOTIATE)
-		conn->need_neg = false;
+/**
+ * smb1_allocate_rsp_buf() - allocate response buffer for a command
+ * @work:	smb work containing smb request
+ *
+ * Return:      0 on success, otherwise -ENOMEM
+ */
+static int smb1_allocate_rsp_buf(struct ksmbd_work *work)
+{
+	work->response_buf = kzalloc(MAX_CIFS_SMALL_BUFFER_SIZE,
+			GFP_KERNEL);
+	work->response_sz = MAX_CIFS_SMALL_BUFFER_SIZE;
+
+	if (!work->response_buf) {
+		pr_err("Failed to allocate %u bytes buffer\n",
+				MAX_CIFS_SMALL_BUFFER_SIZE);
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+/**
+ * set_smb1_rsp_status() - set error type in smb response header
+ * @work:	smb work containing smb response header
+ * @err:	error code to set in response
+ */
+static void set_smb1_rsp_status(struct ksmbd_work *work, __le32 err)
+{
+	work->send_no_response = 1;
+}
+
+static struct smb_version_ops smb1_server_ops = {
+	.get_cmd_val = get_smb1_cmd_val,
+	.init_rsp_hdr = init_smb1_rsp_hdr,
+	.allocate_rsp_buf = smb1_allocate_rsp_buf,
+	.check_user_session = smb1_check_user_session,
+	.set_rsp_status = set_smb1_rsp_status,
+};
+
+static int smb1_negotiate(struct ksmbd_work *work)
+{
+	return ksmbd_smb_negotiate_common(work, SMB_COM_NEGOTIATE);
+}
+
+static struct smb_version_cmds smb1_server_cmds[1] = {
+	[SMB_COM_NEGOTIATE_EX]	= { .proc = smb1_negotiate, },
+};
+
+static int init_smb1_server(struct ksmbd_conn *conn)
+{
+	conn->ops = &smb1_server_ops;
+	conn->cmds = smb1_server_cmds;
+	conn->max_cmds = ARRAY_SIZE(smb1_server_cmds);
 	return 0;
 }
 
+int ksmbd_init_smb_server(struct ksmbd_work *work)
+{
+	struct ksmbd_conn *conn = work->conn;
+	__le32 proto;
+
+	proto = *(__le32 *)((struct smb_hdr *)work->request_buf)->Protocol;
+	if (conn->need_neg == false) {
+		if (proto == SMB1_PROTO_NUMBER)
+			return -EINVAL;
+		return 0;
+	}
+
+	if (proto == SMB1_PROTO_NUMBER)
+		return init_smb1_server(conn);
+	return init_smb3_11_server(conn);
+}
+
 int ksmbd_populate_dot_dotdot_entries(struct ksmbd_work *work, int info_level,
 				      struct ksmbd_file *dir,
 				      struct ksmbd_dir_info *d_info,
@@ -308,14 +437,17 @@
 	for (i = 0; i < 2; i++) {
 		struct kstat kstat;
 		struct ksmbd_kstat ksmbd_kstat;
+		struct dentry *dentry;
 
 		if (!dir->dot_dotdot[i]) { /* fill dot entry info */
 			if (i == 0) {
 				d_info->name = ".";
 				d_info->name_len = 1;
+				dentry = dir->filp->f_path.dentry;
 			} else {
 				d_info->name = "..";
 				d_info->name_len = 2;
+				dentry = dir->filp->f_path.dentry->d_parent;
 			}
 
 			if (!match_pattern(d_info->name, d_info->name_len,
@@ -327,7 +459,7 @@
 			ksmbd_kstat.kstat = &kstat;
 			ksmbd_vfs_fill_dentry_attrs(work,
 						    user_ns,
-						    dir->filp->f_path.dentry->d_parent,
+						    dentry,
 						    &ksmbd_kstat);
 			rc = fn(conn, info_level, d_info, &ksmbd_kstat);
 			if (rc)
@@ -416,7 +548,7 @@
 	out[baselen + 3] = PERIOD;
 
 	if (dot_present)
-		memcpy(&out[baselen + 4], extension, 4);
+		memcpy(out + baselen + 4, extension, 4);
 	else
 		out[baselen + 4] = '\0';
 	smbConvertToUTF16((__le16 *)shortname, out, PATH_MAX,
@@ -427,7 +559,7 @@
 
 static int __smb2_negotiate(struct ksmbd_conn *conn)
 {
-	return (conn->dialect >= SMB21_PROT_ID &&
+	return (conn->dialect >= SMB20_PROT_ID &&
 		conn->dialect <= SMB311_PROT_ID);
 }
 
@@ -435,9 +567,17 @@
 {
 	struct smb_negotiate_rsp *neg_rsp = work->response_buf;
 
-	ksmbd_debug(SMB, "Unsupported SMB protocol\n");
-	neg_rsp->hdr.Status.CifsError = STATUS_INVALID_LOGON_TYPE;
-	return -EINVAL;
+	ksmbd_debug(SMB, "Unsupported SMB1 protocol\n");
+
+	if (ksmbd_iov_pin_rsp(work, (void *)neg_rsp,
+			      sizeof(struct smb_negotiate_rsp) - 4))
+		return -ENOMEM;
+
+	neg_rsp->hdr.Status.CifsError = STATUS_SUCCESS;
+	neg_rsp->hdr.WordCount = 1;
+	neg_rsp->DialectIndex = cpu_to_le16(work->conn->dialect);
+	neg_rsp->ByteCount = 0;
+	return 0;
 }
 
 int ksmbd_smb_negotiate_common(struct ksmbd_work *work, unsigned int command)
@@ -445,27 +585,17 @@
 	struct ksmbd_conn *conn = work->conn;
 	int ret;
 
-	conn->dialect = ksmbd_negotiate_smb_dialect(work->request_buf);
+	conn->dialect =
+		ksmbd_negotiate_smb_dialect(work->request_buf);
 	ksmbd_debug(SMB, "conn->dialect 0x%x\n", conn->dialect);
 
 	if (command == SMB2_NEGOTIATE_HE) {
-		struct smb2_hdr *smb2_hdr = work->request_buf;
-
-		if (smb2_hdr->ProtocolId != SMB2_PROTO_NUMBER) {
-			ksmbd_debug(SMB, "Downgrade to SMB1 negotiation\n");
-			command = SMB_COM_NEGOTIATE;
-		}
-	}
-
-	if (command == SMB2_NEGOTIATE_HE && __smb2_negotiate(conn)) {
 		ret = smb2_handle_negotiate(work);
-		init_smb2_neg_rsp(work);
 		return ret;
 	}
 
 	if (command == SMB_COM_NEGOTIATE) {
 		if (__smb2_negotiate(conn)) {
-			conn->need_neg = true;
 			init_smb3_11_server(conn);
 			init_smb2_neg_rsp(work);
 			ksmbd_debug(SMB, "Upgrade to SMB2 negotiation\n");
@@ -619,8 +749,8 @@
 	if (!cred)
 		return -ENOMEM;
 
-	cred->fsuid = make_kuid(current_user_ns(), uid);
-	cred->fsgid = make_kgid(current_user_ns(), gid);
+	cred->fsuid = make_kuid(&init_user_ns, uid);
+	cred->fsgid = make_kgid(&init_user_ns, gid);
 
 	gi = groups_alloc(0);
 	if (!gi) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smb_common.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smb_common.h
@@ -205,8 +205,15 @@
 
 #define SMB1_PROTO_NUMBER		cpu_to_le32(0x424d53ff)
 #define SMB_COM_NEGOTIATE		0x72
-
 #define SMB1_CLIENT_GUID_SIZE		(16)
+
+#define SMBFLG_RESPONSE 0x80	/* this PDU is a response from server */
+
+#define SMBFLG2_IS_LONG_NAME	cpu_to_le16(0x40)
+#define SMBFLG2_EXT_SEC		cpu_to_le16(0x800)
+#define SMBFLG2_ERR_STATUS	cpu_to_le16(0x4000)
+#define SMBFLG2_UNICODE		cpu_to_le16(0x8000)
+
 struct smb_hdr {
 	__be32 smb_buf_length;
 	__u8 Protocol[4];
@@ -240,34 +247,13 @@
 struct smb_negotiate_req {
 	struct smb_hdr hdr;     /* wct = 0 */
 	__le16 ByteCount;
-	unsigned char DialectsArray[1];
+	unsigned char DialectsArray[];
 } __packed;
 
 struct smb_negotiate_rsp {
 	struct smb_hdr hdr;     /* wct = 17 */
 	__le16 DialectIndex; /* 0xFFFF = no dialect acceptable */
-	__u8 SecurityMode;
-	__le16 MaxMpxCount;
-	__le16 MaxNumberVcs;
-	__le32 MaxBufferSize;
-	__le32 MaxRawSize;
-	__le32 SessionKey;
-	__le32 Capabilities;    /* see below */
-	__le32 SystemTimeLow;
-	__le32 SystemTimeHigh;
-	__le16 ServerTimeZone;
-	__u8 EncryptionKeyLength;
 	__le16 ByteCount;
-	union {
-		unsigned char EncryptionKey[8]; /* cap extended security off */
-		/* followed by Domain name - if extended security is off */
-		/* followed by 16 bytes of server GUID */
-		/* then security blob if cap_extended_security negotiated */
-		struct {
-			unsigned char GUID[SMB1_CLIENT_GUID_SIZE];
-			unsigned char SecurityBlob[1];
-		} __packed extended_response;
-	} __packed u;
 } __packed;
 
 struct filesystem_attribute_info {
@@ -324,14 +310,14 @@
 	__le64 AllocationSize;
 	__le32 ExtFileAttributes;
 	__le32 FileNameLength;
-	char FileName[1];
+	char FileName[];
 } __packed;   /* level 0x101 FF resp data */
 
 struct file_names_info {
 	__le32 NextEntryOffset;
 	__u32 FileIndex;
 	__le32 FileNameLength;
-	char FileName[1];
+	char FileName[];
 } __packed;   /* level 0xc FF resp data */
 
 struct file_full_directory_info {
@@ -346,7 +332,7 @@
 	__le32 ExtFileAttributes;
 	__le32 FileNameLength;
 	__le32 EaSize;
-	char FileName[1];
+	char FileName[];
 } __packed; /* level 0x102 FF resp */
 
 struct file_both_directory_info {
@@ -364,7 +350,7 @@
 	__u8   ShortNameLength;
 	__u8   Reserved;
 	__u8   ShortName[24];
-	char FileName[1];
+	char FileName[];
 } __packed; /* level 0x104 FFrsp data */
 
 struct file_id_both_directory_info {
@@ -384,7 +370,7 @@
 	__u8   ShortName[24];
 	__le16 Reserved2;
 	__le64 UniqueId;
-	char FileName[1];
+	char FileName[];
 } __packed;
 
 struct file_id_full_dir_info {
@@ -401,7 +387,7 @@
 	__le32 EaSize; /* EA size */
 	__le32 Reserved;
 	__le64 UniqueId; /* inode num - le since Samba puts ino in low 32 bit*/
-	char FileName[1];
+	char FileName[];
 } __packed; /* level 0x105 FF rsp data */
 
 struct smb_version_values {
@@ -412,6 +398,7 @@
 	__u32		max_read_size;
 	__u32		max_write_size;
 	__u32		max_trans_size;
+	__u32		max_credits;
 	__u32		large_lock_type;
 	__u32		exclusive_lock_type;
 	__u32		shared_lock_type;
@@ -467,7 +454,7 @@
 	int (*check_sign_req)(struct ksmbd_work *work);
 	void (*set_sign_rsp)(struct ksmbd_work *work);
 	int (*generate_signingkey)(struct ksmbd_session *sess, struct ksmbd_conn *conn);
-	int (*generate_encryptionkey)(struct ksmbd_session *sess);
+	int (*generate_encryptionkey)(struct ksmbd_conn *conn, struct ksmbd_session *sess);
 	bool (*is_transform_hdr)(void *buf);
 	int (*decrypt_req)(struct ksmbd_work *work);
 	int (*encrypt_resp)(struct ksmbd_work *work);
@@ -477,12 +464,6 @@
 	int (*proc)(struct ksmbd_work *swork);
 };
 
-static inline size_t
-smb2_hdr_size_no_buflen(struct smb_version_values *vals)
-{
-	return vals->header_size - 4;
-}
-
 int ksmbd_min_protocol(void);
 int ksmbd_max_protocol(void);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smbacl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smbacl.c
@@ -9,6 +9,7 @@
 #include <linux/fs.h>
 #include <linux/slab.h>
 #include <linux/string.h>
+#include <linux/mnt_idmapping.h>
 
 #include "smbacl.h"
 #include "smb_common.h"
@@ -96,7 +97,7 @@
 	/* compare all of the subauth values if any */
 	num_sat = ctsid->num_subauth;
 	num_saw = cwsid->num_subauth;
-	num_subauth = num_sat < num_saw ? num_sat : num_saw;
+	num_subauth = min(num_sat, num_saw);
 	if (num_subauth) {
 		for (i = 0; i < num_subauth; ++i) {
 			if (ctsid->sub_auth[i] != cwsid->sub_auth[i]) {
@@ -274,14 +275,7 @@
 		uid_t id;
 
 		id = le32_to_cpu(psid->sub_auth[psid->num_subauth - 1]);
-		/*
-		 * Translate raw sid into kuid in the server's user
-		 * namespace.
-		 */
-		uid = make_kuid(&init_user_ns, id);
-
-		/* If this is an idmapped mount, apply the idmapping. */
-		uid = kuid_from_mnt(user_ns, uid);
+		uid = mapped_kuid_user(user_ns, &init_user_ns, KUIDT_INIT(id));
 		if (uid_valid(uid)) {
 			fattr->cf_uid = uid;
 			rc = 0;
@@ -291,14 +285,7 @@
 		gid_t id;
 
 		id = le32_to_cpu(psid->sub_auth[psid->num_subauth - 1]);
-		/*
-		 * Translate raw sid into kgid in the server's user
-		 * namespace.
-		 */
-		gid = make_kgid(&init_user_ns, id);
-
-		/* If this is an idmapped mount, apply the idmapping. */
-		gid = kgid_from_mnt(user_ns, gid);
+		gid = mapped_kgid_user(user_ns, &init_user_ns, KGIDT_INIT(id));
 		if (gid_valid(gid)) {
 			fattr->cf_gid = gid;
 			rc = 0;
@@ -409,11 +396,9 @@
 	if (num_aces <= 0)
 		return;
 
-	if (num_aces > ULONG_MAX / sizeof(struct smb_ace *))
-		return;
-
-	ppace = kmalloc_array(num_aces, sizeof(struct smb_ace *), GFP_KERNEL);
-	if (!ppace)
+	if (num_aces > (le16_to_cpu(pdacl->size) - sizeof(struct smb_acl)) /
+			(offsetof(struct smb_ace, sid) +
+			 offsetof(struct smb_sid, sub_auth) + sizeof(__le16)))
 		return;
 
 	ret = init_acl_state(&acl_state, num_aces);
@@ -425,6 +410,13 @@
 		return;
 	}
 
+	ppace = kmalloc_array(num_aces, sizeof(struct smb_ace *), GFP_KERNEL);
+	if (!ppace) {
+		free_acl_state(&default_acl_state);
+		free_acl_state(&acl_state);
+		return;
+	}
+
 	/*
 	 * reset rwx permissions for user/group/other.
 	 * Also, if num_aces is 0 i.e. DACL has no ACEs,
@@ -440,6 +432,7 @@
 			offsetof(struct smb_sid, sub_auth);
 
 		if (end_of_acl - acl_base < acl_size ||
+		    ppace[i]->sid.num_subauth == 0 ||
 		    ppace[i]->sid.num_subauth > SID_MAX_SUB_AUTHORITIES ||
 		    (end_of_acl - acl_base <
 		     acl_size + sizeof(__le32) * ppace[i]->sid.num_subauth) ||
@@ -703,6 +696,7 @@
 static void set_ntacl_dacl(struct user_namespace *user_ns,
 			   struct smb_acl *pndacl,
 			   struct smb_acl *nt_dacl,
+			   unsigned int aces_size,
 			   const struct smb_sid *pownersid,
 			   const struct smb_sid *pgrpsid,
 			   struct smb_fattr *fattr)
@@ -716,9 +710,19 @@
 	if (nt_num_aces) {
 		ntace = (struct smb_ace *)((char *)nt_dacl + sizeof(struct smb_acl));
 		for (i = 0; i < nt_num_aces; i++) {
-			memcpy((char *)pndace + size, ntace, le16_to_cpu(ntace->size));
-			size += le16_to_cpu(ntace->size);
-			ntace = (struct smb_ace *)((char *)ntace + le16_to_cpu(ntace->size));
+			unsigned short nt_ace_size;
+
+			if (offsetof(struct smb_ace, access_req) > aces_size)
+				break;
+
+			nt_ace_size = le16_to_cpu(ntace->size);
+			if (nt_ace_size > aces_size)
+				break;
+
+			memcpy((char *)pndace + size, ntace, nt_ace_size);
+			size += nt_ace_size;
+			aces_size -= nt_ace_size;
+			ntace = (struct smb_ace *)((char *)ntace + nt_ace_size);
 			num_aces++;
 		}
 	}
@@ -891,7 +895,7 @@
 /* Convert permission bits from mode to equivalent CIFS ACL */
 int build_sec_desc(struct user_namespace *user_ns,
 		   struct smb_ntsd *pntsd, struct smb_ntsd *ppntsd,
-		   int addition_info, __u32 *secdesclen,
+		   int ppntsd_size, int addition_info, __u32 *secdesclen,
 		   struct smb_fattr *fattr)
 {
 	int rc = 0;
@@ -951,15 +955,25 @@
 
 		if (!ppntsd) {
 			set_mode_dacl(user_ns, dacl_ptr, fattr);
-		} else if (!ppntsd->dacloffset) {
-			goto out;
 		} else {
 			struct smb_acl *ppdacl_ptr;
+			unsigned int dacl_offset = le32_to_cpu(ppntsd->dacloffset);
+			int ppdacl_size, ntacl_size = ppntsd_size - dacl_offset;
+
+			if (!dacl_offset ||
+			    (dacl_offset + sizeof(struct smb_acl) > ppntsd_size))
+				goto out;
+
+			ppdacl_ptr = (struct smb_acl *)((char *)ppntsd + dacl_offset);
+			ppdacl_size = le16_to_cpu(ppdacl_ptr->size);
+			if (ppdacl_size > ntacl_size ||
+			    ppdacl_size < sizeof(struct smb_acl))
+				goto out;
 
-			ppdacl_ptr = (struct smb_acl *)((char *)ppntsd +
-						le32_to_cpu(ppntsd->dacloffset));
 			set_ntacl_dacl(user_ns, dacl_ptr, ppdacl_ptr,
-				       nowner_sid_ptr, ngroup_sid_ptr, fattr);
+				       ntacl_size - sizeof(struct smb_acl),
+				       nowner_sid_ptr, ngroup_sid_ptr,
+				       fattr);
 		}
 		pntsd->dacloffset = cpu_to_le32(offset);
 		offset += le16_to_cpu(dacl_ptr->size);
@@ -983,7 +997,7 @@
 }
 
 int smb_inherit_dacl(struct ksmbd_conn *conn,
-		     struct path *path,
+		     const struct path *path,
 		     unsigned int uid, unsigned int gid)
 {
 	const struct smb_sid *psid, *creator = NULL;
@@ -993,24 +1007,31 @@
 	struct smb_sid owner_sid, group_sid;
 	struct dentry *parent = path->dentry->d_parent;
 	struct user_namespace *user_ns = mnt_user_ns(path->mnt);
-	int inherited_flags = 0, flags = 0, i, ace_cnt = 0, nt_size = 0;
-	int rc = 0, num_aces, dacloffset, pntsd_type, acl_len;
+	int inherited_flags = 0, flags = 0, i, ace_cnt = 0, nt_size = 0, pdacl_size;
+	int rc = 0, num_aces, dacloffset, pntsd_type, pntsd_size, acl_len, aces_size;
 	char *aces_base;
 	bool is_dir = S_ISDIR(d_inode(path->dentry)->i_mode);
 
-	acl_len = ksmbd_vfs_get_sd_xattr(conn, user_ns,
-					 parent, &parent_pntsd);
-	if (acl_len <= 0)
+	pntsd_size = ksmbd_vfs_get_sd_xattr(conn, user_ns,
+					    parent, &parent_pntsd);
+	if (pntsd_size <= 0)
 		return -ENOENT;
 	dacloffset = le32_to_cpu(parent_pntsd->dacloffset);
-	if (!dacloffset) {
+	if (!dacloffset || (dacloffset + sizeof(struct smb_acl) > pntsd_size)) {
 		rc = -EINVAL;
 		goto free_parent_pntsd;
 	}
 
 	parent_pdacl = (struct smb_acl *)((char *)parent_pntsd + dacloffset);
+	acl_len = pntsd_size - dacloffset;
 	num_aces = le32_to_cpu(parent_pdacl->num_aces);
 	pntsd_type = le16_to_cpu(parent_pntsd->type);
+	pdacl_size = le16_to_cpu(parent_pdacl->size);
+
+	if (pdacl_size > acl_len || pdacl_size < sizeof(struct smb_acl)) {
+		rc = -EINVAL;
+		goto free_parent_pntsd;
+	}
 
 	aces_base = kmalloc(sizeof(struct smb_ace) * num_aces * 2, GFP_KERNEL);
 	if (!aces_base) {
@@ -1021,11 +1042,23 @@
 	aces = (struct smb_ace *)aces_base;
 	parent_aces = (struct smb_ace *)((char *)parent_pdacl +
 			sizeof(struct smb_acl));
+	aces_size = acl_len - sizeof(struct smb_acl);
 
 	if (pntsd_type & DACL_AUTO_INHERITED)
 		inherited_flags = INHERITED_ACE;
 
 	for (i = 0; i < num_aces; i++) {
+		int pace_size;
+
+		if (offsetof(struct smb_ace, access_req) > aces_size)
+			break;
+
+		pace_size = le16_to_cpu(parent_aces->size);
+		if (pace_size > aces_size)
+			break;
+
+		aces_size -= pace_size;
+
 		flags = parent_aces->flags;
 		if (!smb_inherit_flags(flags, is_dir))
 			goto pass;
@@ -1070,8 +1103,7 @@
 		aces = (struct smb_ace *)((char *)aces + le16_to_cpu(aces->size));
 		ace_cnt++;
 pass:
-		parent_aces =
-			(struct smb_ace *)((char *)parent_aces + le16_to_cpu(parent_aces->size));
+		parent_aces = (struct smb_ace *)((char *)parent_aces + pace_size);
 	}
 
 	if (nt_size > 0) {
@@ -1079,6 +1111,7 @@
 		struct smb_acl *pdacl;
 		struct smb_sid *powner_sid = NULL, *pgroup_sid = NULL;
 		int powner_sid_size = 0, pgroup_sid_size = 0, pntsd_size;
+		int pntsd_alloc_size;
 
 		if (parent_pntsd->osidoffset) {
 			powner_sid = (struct smb_sid *)((char *)parent_pntsd +
@@ -1091,9 +1124,10 @@
 			pgroup_sid_size = 1 + 1 + 6 + (pgroup_sid->num_subauth * 4);
 		}
 
-		pntsd = kzalloc(sizeof(struct smb_ntsd) + powner_sid_size +
-				pgroup_sid_size + sizeof(struct smb_acl) +
-				nt_size, GFP_KERNEL);
+		pntsd_alloc_size = sizeof(struct smb_ntsd) + powner_sid_size +
+			pgroup_sid_size + sizeof(struct smb_acl) + nt_size;
+
+		pntsd = kzalloc(pntsd_alloc_size, GFP_KERNEL);
 		if (!pntsd) {
 			rc = -ENOMEM;
 			goto free_aces_base;
@@ -1108,6 +1142,27 @@
 		pntsd->gsidoffset = parent_pntsd->gsidoffset;
 		pntsd->dacloffset = parent_pntsd->dacloffset;
 
+		if ((u64)le32_to_cpu(pntsd->osidoffset) + powner_sid_size >
+		    pntsd_alloc_size) {
+			rc = -EINVAL;
+			kfree(pntsd);
+			goto free_aces_base;
+		}
+
+		if ((u64)le32_to_cpu(pntsd->gsidoffset) + pgroup_sid_size >
+		    pntsd_alloc_size) {
+			rc = -EINVAL;
+			kfree(pntsd);
+			goto free_aces_base;
+		}
+
+		if ((u64)le32_to_cpu(pntsd->dacloffset) + sizeof(struct smb_acl) + nt_size >
+		    pntsd_alloc_size) {
+			rc = -EINVAL;
+			kfree(pntsd);
+			goto free_aces_base;
+		}
+
 		if (pntsd->osidoffset) {
 			struct smb_sid *owner_sid = (struct smb_sid *)((char *)pntsd +
 					le32_to_cpu(pntsd->osidoffset));
@@ -1134,8 +1189,7 @@
 			pntsd_size += sizeof(struct smb_acl) + nt_size;
 		}
 
-		ksmbd_vfs_set_sd_xattr(conn, user_ns,
-				       path->dentry, pntsd, pntsd_size);
+		ksmbd_vfs_set_sd_xattr(conn, user_ns, path, pntsd, pntsd_size, false);
 		kfree(pntsd);
 	}
 
@@ -1159,14 +1213,14 @@
 	return false;
 }
 
-int smb_check_perm_dacl(struct ksmbd_conn *conn, struct path *path,
+int smb_check_perm_dacl(struct ksmbd_conn *conn, const struct path *path,
 			__le32 *pdaccess, int uid)
 {
 	struct user_namespace *user_ns = mnt_user_ns(path->mnt);
 	struct smb_ntsd *pntsd = NULL;
 	struct smb_acl *pdacl;
 	struct posix_acl *posix_acls;
-	int rc = 0, acl_size;
+	int rc = 0, pntsd_size, acl_size, aces_size, pdacl_size, dacl_offset;
 	struct smb_sid sid;
 	int granted = le32_to_cpu(*pdaccess & ~FILE_MAXIMAL_ACCESS_LE);
 	struct smb_ace *ace;
@@ -1175,37 +1229,33 @@
 	struct smb_ace *others_ace = NULL;
 	struct posix_acl_entry *pa_entry;
 	unsigned int sid_type = SIDOWNER;
-	char *end_of_acl;
+	unsigned short ace_size;
 
 	ksmbd_debug(SMB, "check permission using windows acl\n");
-	acl_size = ksmbd_vfs_get_sd_xattr(conn, user_ns,
-					  path->dentry, &pntsd);
-	if (acl_size <= 0 || !pntsd || !pntsd->dacloffset) {
-		kfree(pntsd);
-		return 0;
-	}
+	pntsd_size = ksmbd_vfs_get_sd_xattr(conn, user_ns,
+					    path->dentry, &pntsd);
+	if (pntsd_size <= 0 || !pntsd)
+		goto err_out;
+
+	dacl_offset = le32_to_cpu(pntsd->dacloffset);
+	if (!dacl_offset ||
+	    (dacl_offset + sizeof(struct smb_acl) > pntsd_size))
+		goto err_out;
 
 	pdacl = (struct smb_acl *)((char *)pntsd + le32_to_cpu(pntsd->dacloffset));
-	end_of_acl = ((char *)pntsd) + acl_size;
-	if (end_of_acl <= (char *)pdacl) {
-		kfree(pntsd);
-		return 0;
-	}
+	acl_size = pntsd_size - dacl_offset;
+	pdacl_size = le16_to_cpu(pdacl->size);
 
-	if (end_of_acl < (char *)pdacl + le16_to_cpu(pdacl->size) ||
-	    le16_to_cpu(pdacl->size) < sizeof(struct smb_acl)) {
-		kfree(pntsd);
-		return 0;
-	}
+	if (pdacl_size > acl_size || pdacl_size < sizeof(struct smb_acl))
+		goto err_out;
 
 	if (!pdacl->num_aces) {
-		if (!(le16_to_cpu(pdacl->size) - sizeof(struct smb_acl)) &&
+		if (!(pdacl_size - sizeof(struct smb_acl)) &&
 		    *pdaccess & ~(FILE_READ_CONTROL_LE | FILE_WRITE_DAC_LE)) {
 			rc = -EACCES;
 			goto err_out;
 		}
-		kfree(pntsd);
-		return 0;
+		goto err_out;
 	}
 
 	if (*pdaccess & FILE_MAXIMAL_ACCESS_LE) {
@@ -1213,11 +1263,16 @@
 			DELETE;
 
 		ace = (struct smb_ace *)((char *)pdacl + sizeof(struct smb_acl));
+		aces_size = acl_size - sizeof(struct smb_acl);
 		for (i = 0; i < le32_to_cpu(pdacl->num_aces); i++) {
+			if (offsetof(struct smb_ace, access_req) > aces_size)
+				break;
+			ace_size = le16_to_cpu(ace->size);
+			if (ace_size > aces_size)
+				break;
+			aces_size -= ace_size;
 			granted |= le32_to_cpu(ace->access_req);
 			ace = (struct smb_ace *)((char *)ace + le16_to_cpu(ace->size));
-			if (end_of_acl < (char *)ace)
-				goto err_out;
 		}
 
 		if (!pdacl->num_aces)
@@ -1229,7 +1284,15 @@
 	id_to_sid(uid, sid_type, &sid);
 
 	ace = (struct smb_ace *)((char *)pdacl + sizeof(struct smb_acl));
+	aces_size = acl_size - sizeof(struct smb_acl);
 	for (i = 0; i < le32_to_cpu(pdacl->num_aces); i++) {
+		if (offsetof(struct smb_ace, access_req) > aces_size)
+			break;
+		ace_size = le16_to_cpu(ace->size);
+		if (ace_size > aces_size)
+			break;
+		aces_size -= ace_size;
+
 		if (!compare_sids(&sid, &ace->sid) ||
 		    !compare_sids(&sid_unix_NFS_mode, &ace->sid)) {
 			found = 1;
@@ -1239,8 +1302,6 @@
 			others_ace = ace;
 
 		ace = (struct smb_ace *)((char *)ace + le16_to_cpu(ace->size));
-		if (end_of_acl < (char *)ace)
-			goto err_out;
 	}
 
 	if (*pdaccess & FILE_MAXIMAL_ACCESS_LE && found) {
@@ -1255,7 +1316,7 @@
 
 	if (IS_ENABLED(CONFIG_FS_POSIX_ACL)) {
 		posix_acls = get_acl(d_inode(path->dentry), ACL_TYPE_ACCESS);
-		if (posix_acls && !found) {
+		if (!IS_ERR_OR_NULL(posix_acls) && !found) {
 			unsigned int id = -1;
 
 			pa_entry = posix_acls->a_entries;
@@ -1274,11 +1335,12 @@
 					if (!access_bits)
 						access_bits =
 							SET_MINIMUM_RIGHTS;
+					posix_acl_release(posix_acls);
 					goto check_access_bits;
 				}
 			}
 		}
-		if (posix_acls)
+		if (!IS_ERR_OR_NULL(posix_acls))
 			posix_acl_release(posix_acls);
 	}
 
@@ -1318,8 +1380,8 @@
 }
 
 int set_info_sec(struct ksmbd_conn *conn, struct ksmbd_tree_connect *tcon,
-		 struct path *path, struct smb_ntsd *pntsd, int ntsd_len,
-		 bool type_check)
+		 const struct path *path, struct smb_ntsd *pntsd, int ntsd_len,
+		 bool type_check, bool get_write)
 {
 	int rc;
 	struct smb_fattr fattr = {{0}};
@@ -1347,7 +1409,7 @@
 	newattrs.ia_valid |= ATTR_MODE;
 	newattrs.ia_mode = (inode->i_mode & ~0777) | (fattr.cf_mode & 0777);
 
-	ksmbd_vfs_remove_acl_xattrs(user_ns, path->dentry);
+	ksmbd_vfs_remove_acl_xattrs(user_ns, path);
 	/* Update posix acls */
 	if (IS_ENABLED(CONFIG_FS_POSIX_ACL) && fattr.cf_dacls) {
 		rc = set_posix_acl(user_ns, inode,
@@ -1378,15 +1440,14 @@
 
 	if (test_share_config_flag(tcon->share_conf, KSMBD_SHARE_FLAG_ACL_XATTR)) {
 		/* Update WinACL in xattr */
-		ksmbd_vfs_remove_sd_xattrs(user_ns, path->dentry);
-		ksmbd_vfs_set_sd_xattr(conn, user_ns,
-				       path->dentry, pntsd, ntsd_len);
+		ksmbd_vfs_remove_sd_xattrs(user_ns, path);
+		ksmbd_vfs_set_sd_xattr(conn, user_ns, path, pntsd, ntsd_len,
+				get_write);
 	}
 
 out:
 	posix_acl_release(fattr.cf_acls);
 	posix_acl_release(fattr.cf_dacls);
-	mark_inode_dirty(inode);
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/smbacl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/smbacl.h
@@ -11,6 +11,7 @@
 #include <linux/fs.h>
 #include <linux/namei.h>
 #include <linux/posix_acl.h>
+#include <linux/mnt_idmapping.h>
 
 #include "mgmt/tree_connect.h"
 
@@ -192,7 +193,7 @@
 int parse_sec_desc(struct user_namespace *user_ns, struct smb_ntsd *pntsd,
 		   int acl_len, struct smb_fattr *fattr);
 int build_sec_desc(struct user_namespace *user_ns, struct smb_ntsd *pntsd,
-		   struct smb_ntsd *ppntsd, int addition_info,
+		   struct smb_ntsd *ppntsd, int ppntsd_size, int addition_info,
 		   __u32 *secdesclen, struct smb_fattr *fattr);
 int init_acl_state(struct posix_acl_state *state, int cnt);
 void free_acl_state(struct posix_acl_state *state);
@@ -200,13 +201,13 @@
 			struct posix_acl_entry *pace);
 int compare_sids(const struct smb_sid *ctsid, const struct smb_sid *cwsid);
 bool smb_inherit_flags(int flags, bool is_dir);
-int smb_inherit_dacl(struct ksmbd_conn *conn, struct path *path,
+int smb_inherit_dacl(struct ksmbd_conn *conn, const struct path *path,
 		     unsigned int uid, unsigned int gid);
-int smb_check_perm_dacl(struct ksmbd_conn *conn, struct path *path,
+int smb_check_perm_dacl(struct ksmbd_conn *conn, const struct path *path,
 			__le32 *pdaccess, int uid);
 int set_info_sec(struct ksmbd_conn *conn, struct ksmbd_tree_connect *tcon,
-		 struct path *path, struct smb_ntsd *pntsd, int ntsd_len,
-		 bool type_check);
+		 const struct path *path, struct smb_ntsd *pntsd, int ntsd_len,
+		 bool type_check, bool get_write);
 void id_to_sid(unsigned int cid, uint sidtype, struct smb_sid *ssid);
 void ksmbd_init_domain(u32 *sub_auth);
 
@@ -216,7 +217,7 @@
 	kuid_t kuid;
 
 	/* If this is an idmapped mount, apply the idmapping. */
-	kuid = kuid_into_mnt(mnt_userns, pace->e_uid);
+	kuid = mapped_kuid_fs(mnt_userns, &init_user_ns, pace->e_uid);
 
 	/* Translate the kuid into a userspace id ksmbd would see. */
 	return from_kuid(&init_user_ns, kuid);
@@ -228,7 +229,7 @@
 	kgid_t kgid;
 
 	/* If this is an idmapped mount, apply the idmapping. */
-	kgid = kgid_into_mnt(mnt_userns, pace->e_gid);
+	kgid = mapped_kgid_fs(mnt_userns, &init_user_ns, pace->e_gid);
 
 	/* Translate the kgid into a userspace id ksmbd would see. */
 	return from_kgid(&init_user_ns, kgid);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/transport_ipc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/transport_ipc.c
@@ -26,6 +26,7 @@
 #include "mgmt/ksmbd_ida.h"
 #include "connection.h"
 #include "transport_tcp.h"
+#include "transport_rdma.h"
 
 #define IPC_WAIT_TIMEOUT	(2 * HZ)
 
@@ -64,6 +65,7 @@
 	struct hlist_node	ipc_table_hlist;
 
 	void			*response;
+	unsigned int		msg_sz;
 };
 
 static struct delayed_work ipc_timer_work;
@@ -73,7 +75,7 @@
 static int handle_generic_event(struct sk_buff *skb, struct genl_info *info);
 static int ksmbd_ipc_heartbeat_request(void);
 
-static const struct nla_policy ksmbd_nl_policy[KSMBD_EVENT_MAX] = {
+static const struct nla_policy ksmbd_nl_policy[KSMBD_EVENT_MAX + 1] = {
 	[KSMBD_EVENT_UNSPEC] = {
 		.len = 0,
 	},
@@ -227,7 +229,7 @@
 	struct ksmbd_ipc_msg *msg;
 	size_t msg_sz = sz + sizeof(struct ksmbd_ipc_msg);
 
-	msg = kvmalloc(msg_sz, GFP_KERNEL | __GFP_ZERO);
+	msg = kvzalloc(msg_sz, GFP_KERNEL);
 	if (msg)
 		msg->sz = sz;
 	return msg;
@@ -266,13 +268,14 @@
 			       entry->type + 1, type);
 		}
 
-		entry->response = kvmalloc(sz, GFP_KERNEL | __GFP_ZERO);
+		entry->response = kvzalloc(sz, GFP_KERNEL);
 		if (!entry->response) {
 			ret = -ENOMEM;
 			break;
 		}
 
 		memcpy(entry->response, payload, sz);
+		entry->msg_sz = sz;
 		wake_up_interruptible(&entry->wait);
 		ret = 0;
 		break;
@@ -301,6 +304,13 @@
 		init_smb2_max_write_size(req->smb2_max_write);
 	if (req->smb2_max_trans)
 		init_smb2_max_trans_size(req->smb2_max_trans);
+	if (req->smb2_max_credits)
+		init_smb2_max_credits(req->smb2_max_credits);
+	if (req->smbd_max_io_size)
+		init_smbd_max_io_size(req->smbd_max_io_size);
+
+	if (req->max_connections)
+		server_conf.max_connections = req->max_connections;
 
 	ret = ksmbd_set_netbios_name(req->netbios_name);
 	ret |= ksmbd_set_server_string(req->server_string);
@@ -394,7 +404,7 @@
 		return -EPERM;
 #endif
 
-	if (type >= KSMBD_EVENT_MAX) {
+	if (type > KSMBD_EVENT_MAX) {
 		WARN_ON(1);
 		return -EINVAL;
 	}
@@ -444,6 +454,34 @@
 	return ret;
 }
 
+static int ipc_validate_msg(struct ipc_msg_table_entry *entry)
+{
+	unsigned int msg_sz = entry->msg_sz;
+
+	if (entry->type == KSMBD_EVENT_RPC_REQUEST) {
+		struct ksmbd_rpc_command *resp = entry->response;
+
+		msg_sz = sizeof(struct ksmbd_rpc_command) + resp->payload_sz;
+	} else if (entry->type == KSMBD_EVENT_SPNEGO_AUTHEN_REQUEST) {
+		struct ksmbd_spnego_authen_response *resp = entry->response;
+
+		msg_sz = sizeof(struct ksmbd_spnego_authen_response) +
+				resp->session_key_len + resp->spnego_blob_len;
+	} else if (entry->type == KSMBD_EVENT_SHARE_CONFIG_REQUEST) {
+		struct ksmbd_share_config_response *resp = entry->response;
+
+		if (resp->payload_sz) {
+			if (resp->payload_sz < resp->veto_list_sz)
+				return -EINVAL;
+
+			msg_sz = sizeof(struct ksmbd_share_config_response) +
+					resp->payload_sz;
+		}
+	}
+
+	return entry->msg_sz != msg_sz ? -EINVAL : 0;
+}
+
 static void *ipc_msg_send_request(struct ksmbd_ipc_msg *msg, unsigned int handle)
 {
 	struct ipc_msg_table_entry entry;
@@ -468,6 +506,13 @@
 	ret = wait_event_interruptible_timeout(entry.wait,
 					       entry.response != NULL,
 					       IPC_WAIT_TIMEOUT);
+	if (entry.response) {
+		ret = ipc_validate_msg(&entry);
+		if (ret) {
+			kvfree(entry.response);
+			entry.response = NULL;
+		}
+	}
 out:
 	down_write(&ipc_msg_table_lock);
 	hash_del(&entry.ipc_table_hlist);
@@ -521,6 +566,9 @@
 	struct ksmbd_spnego_authen_request *req;
 	struct ksmbd_spnego_authen_response *resp;
 
+	if (blob_len > KSMBD_IPC_MAX_PAYLOAD)
+		return NULL;
+
 	msg = ipc_msg_alloc(sizeof(struct ksmbd_spnego_authen_request) +
 			blob_len + 1);
 	if (!msg)
@@ -700,6 +748,9 @@
 	struct ksmbd_rpc_command *req;
 	struct ksmbd_rpc_command *resp;
 
+	if (payload_sz > KSMBD_IPC_MAX_PAYLOAD)
+		return NULL;
+
 	msg = ipc_msg_alloc(sizeof(struct ksmbd_rpc_command) + payload_sz + 1);
 	if (!msg)
 		return NULL;
@@ -748,6 +799,9 @@
 	struct ksmbd_rpc_command *req;
 	struct ksmbd_rpc_command *resp;
 
+	if (payload_sz > KSMBD_IPC_MAX_PAYLOAD)
+		return NULL;
+
 	msg = ipc_msg_alloc(sizeof(struct ksmbd_rpc_command) + payload_sz + 1);
 	if (!msg)
 		return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/transport_rdma.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/transport_rdma.c
@@ -5,16 +5,6 @@
  *
  *   Author(s): Long Li <longli@microsoft.com>,
  *		Hyunchul Lee <hyc.lee@gmail.com>
- *
- *   This program is free software;  you can redistribute it and/or modify
- *   it under the terms of the GNU General Public License as published by
- *   the Free Software Foundation; either version 2 of the License, or
- *   (at your option) any later version.
- *
- *   This program is distributed in the hope that it will be useful,
- *   but WITHOUT ANY WARRANTY;  without even the implied warranty of
- *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See
- *   the GNU General Public License for more details.
  */
 
 #define SUBMOD_NAME	"smb_direct"
@@ -34,14 +24,15 @@
 #include "smbstatus.h"
 #include "transport_rdma.h"
 
-#define SMB_DIRECT_PORT	5445
+#define SMB_DIRECT_PORT_IWARP		5445
+#define SMB_DIRECT_PORT_INFINIBAND	445
 
 #define SMB_DIRECT_VERSION_LE		cpu_to_le16(0x0100)
 
 /* SMB_DIRECT negotiation timeout in seconds */
 #define SMB_DIRECT_NEGOTIATE_TIMEOUT		120
 
-#define SMB_DIRECT_MAX_SEND_SGES		8
+#define SMB_DIRECT_MAX_SEND_SGES		6
 #define SMB_DIRECT_MAX_RECV_SGES		1
 
 /*
@@ -60,6 +51,10 @@
  * as defined in [MS-SMBD] 3.1.1.1
  * Those may change after a SMB_DIRECT negotiation
  */
+
+/* Set 445 port to SMB Direct port by default */
+static int smb_direct_port = SMB_DIRECT_PORT_INFINIBAND;
+
 /* The local peer's maximum number of credits to grant to the peer */
 static int smb_direct_receive_credit_max = 255;
 
@@ -67,17 +62,23 @@
 static int smb_direct_send_credit_target = 255;
 
 /* The maximum single message size can be sent to remote peer */
-static int smb_direct_max_send_size = 8192;
+static int smb_direct_max_send_size = 1364;
 
 /*  The maximum fragmented upper-layer payload receive size supported */
 static int smb_direct_max_fragmented_recv_size = 1024 * 1024;
 
 /*  The maximum single-message size which can be received */
-static int smb_direct_max_receive_size = 8192;
+static int smb_direct_max_receive_size = 1364;
 
-static int smb_direct_max_read_write_size = 1024 * 1024;
+static int smb_direct_max_read_write_size = SMBD_DEFAULT_IOSIZE;
 
-static int smb_direct_max_outstanding_rw_ops = 8;
+static LIST_HEAD(smb_direct_device_list);
+static DEFINE_RWLOCK(smb_direct_device_lock);
+
+struct smb_direct_device {
+	struct ib_device	*ib_dev;
+	struct list_head	list;
+};
 
 static struct smb_direct_listener {
 	struct rdma_cm_id	*cm_id;
@@ -134,18 +135,18 @@
 	atomic_t		send_credits;
 	spinlock_t		lock_new_recv_credits;
 	int			new_recv_credits;
-	atomic_t		rw_avail_ops;
+	int			max_rw_credits;
+	int			pages_per_rw_credit;
+	atomic_t		rw_credits;
 
 	wait_queue_head_t	wait_send_credits;
-	wait_queue_head_t	wait_rw_avail_ops;
+	wait_queue_head_t	wait_rw_credits;
 
 	mempool_t		*sendmsg_mempool;
 	struct kmem_cache	*sendmsg_cache;
 	mempool_t		*recvmsg_mempool;
 	struct kmem_cache	*recvmsg_cache;
 
-	wait_queue_head_t	wait_send_payload_pending;
-	atomic_t		send_payload_pending;
 	wait_queue_head_t	wait_send_pending;
 	atomic_t		send_pending;
 
@@ -195,12 +196,25 @@
 struct smb_direct_rdma_rw_msg {
 	struct smb_direct_transport	*t;
 	struct ib_cqe		cqe;
+	int			status;
 	struct completion	*completion;
+	struct list_head	list;
 	struct rdma_rw_ctx	rw_ctx;
 	struct sg_table		sgt;
 	struct scatterlist	sg_list[0];
 };
 
+void init_smbd_max_io_size(unsigned int sz)
+{
+	sz = clamp_val(sz, SMBD_MIN_IOSIZE, SMBD_MAX_IOSIZE);
+	smb_direct_max_read_write_size = sz;
+}
+
+unsigned int get_smbd_max_read_write_size(void)
+{
+	return smb_direct_max_read_write_size;
+}
+
 static inline int get_buf_page_count(void *buf, int size)
 {
 	return DIV_ROUND_UP((uintptr_t)buf + size, PAGE_SIZE) -
@@ -364,7 +378,7 @@
 	t->reassembly_queue_length = 0;
 	init_waitqueue_head(&t->wait_reassembly_queue);
 	init_waitqueue_head(&t->wait_send_credits);
-	init_waitqueue_head(&t->wait_rw_avail_ops);
+	init_waitqueue_head(&t->wait_rw_credits);
 
 	spin_lock_init(&t->receive_credit_lock);
 	spin_lock_init(&t->recvmsg_queue_lock);
@@ -373,8 +387,6 @@
 	spin_lock_init(&t->empty_recvmsg_queue_lock);
 	INIT_LIST_HEAD(&t->empty_recvmsg_queue);
 
-	init_waitqueue_head(&t->wait_send_payload_pending);
-	atomic_set(&t->send_payload_pending, 0);
 	init_waitqueue_head(&t->wait_send_pending);
 	atomic_set(&t->send_pending, 0);
 
@@ -404,8 +416,6 @@
 	wake_up_interruptible(&t->wait_send_credits);
 
 	ksmbd_debug(RDMA, "wait for all send posted to IB to finish\n");
-	wait_event(t->wait_send_payload_pending,
-		   atomic_read(&t->send_payload_pending) == 0);
 	wait_event(t->wait_send_pending,
 		   atomic_read(&t->send_pending) == 0);
 
@@ -415,6 +425,7 @@
 
 	if (t->qp) {
 		ib_drain_qp(t->qp);
+		ib_mr_pool_destroy(t->qp, &t->qp->rdma_mrs);
 		ib_destroy_qp(t->qp);
 	}
 
@@ -484,7 +495,7 @@
 		struct smb_direct_data_transfer *req =
 			(struct smb_direct_data_transfer *)recvmsg->packet;
 		struct smb2_hdr *hdr = (struct smb2_hdr *)(recvmsg->packet
-				+ le32_to_cpu(req->data_offset) - 4);
+				+ le32_to_cpu(req->data_offset));
 		ksmbd_debug(RDMA,
 			    "CreditGranted: %u, CreditRequested: %u, DataLength: %u, RemainingDataLength: %u, SMB: %x, Command: %u\n",
 			    le16_to_cpu(req->credits_granted),
@@ -555,6 +566,8 @@
 		}
 		t->negotiation_requested = true;
 		t->full_packet_received = true;
+		t->status = SMB_DIRECT_CS_CONNECTED;
+		enqueue_reassembly(t, recvmsg, 0);
 		wake_up_interruptible(&t->wait_status);
 		break;
 	case SMB_DIRECT_MSG_DATA_TRANSFER: {
@@ -657,7 +670,7 @@
 }
 
 static int smb_direct_read(struct ksmbd_transport *t, char *buf,
-			   unsigned int size)
+			   unsigned int size, int unused)
 {
 	struct smb_direct_recvmsg *recvmsg;
 	struct smb_direct_data_transfer *data_transfer;
@@ -858,13 +871,8 @@
 		smb_direct_disconnect_rdma_connection(t);
 	}
 
-	if (sendmsg->num_sge > 1) {
-		if (atomic_dec_and_test(&t->send_payload_pending))
-			wake_up(&t->wait_send_payload_pending);
-	} else {
-		if (atomic_dec_and_test(&t->send_pending))
-			wake_up(&t->wait_send_pending);
-	}
+	if (atomic_dec_and_test(&t->send_pending))
+		wake_up(&t->wait_send_pending);
 
 	/* iterate and free the list of messages in reverse. the list's head
 	 * is invalid.
@@ -896,21 +904,12 @@
 {
 	int ret;
 
-	if (wr->num_sge > 1)
-		atomic_inc(&t->send_payload_pending);
-	else
-		atomic_inc(&t->send_pending);
-
+	atomic_inc(&t->send_pending);
 	ret = ib_post_send(t->qp, wr, NULL);
 	if (ret) {
 		pr_err("failed to post send: %d\n", ret);
-		if (wr->num_sge > 1) {
-			if (atomic_dec_and_test(&t->send_payload_pending))
-				wake_up(&t->wait_send_payload_pending);
-		} else {
-			if (atomic_dec_and_test(&t->send_pending))
-				wake_up(&t->wait_send_pending);
-		}
+		if (atomic_dec_and_test(&t->send_pending))
+			wake_up(&t->wait_send_pending);
 		smb_direct_disconnect_rdma_connection(t);
 	}
 	return ret;
@@ -968,18 +967,19 @@
 }
 
 static int wait_for_credits(struct smb_direct_transport *t,
-			    wait_queue_head_t *waitq, atomic_t *credits)
+			    wait_queue_head_t *waitq, atomic_t *total_credits,
+			    int needed)
 {
 	int ret;
 
 	do {
-		if (atomic_dec_return(credits) >= 0)
+		if (atomic_sub_return(needed, total_credits) >= 0)
 			return 0;
 
-		atomic_inc(credits);
+		atomic_add(needed, total_credits);
 		ret = wait_event_interruptible(*waitq,
-					       atomic_read(credits) > 0 ||
-						t->status != SMB_DIRECT_CS_CONNECTED);
+					       atomic_read(total_credits) >= needed ||
+					       t->status != SMB_DIRECT_CS_CONNECTED);
 
 		if (t->status != SMB_DIRECT_CS_CONNECTED)
 			return -ENOTCONN;
@@ -1000,7 +1000,19 @@
 			return ret;
 	}
 
-	return wait_for_credits(t, &t->wait_send_credits, &t->send_credits);
+	return wait_for_credits(t, &t->wait_send_credits, &t->send_credits, 1);
+}
+
+static int wait_for_rw_credits(struct smb_direct_transport *t, int credits)
+{
+	return wait_for_credits(t, &t->wait_rw_credits, &t->rw_credits, credits);
+}
+
+static int calc_rw_credits(struct smb_direct_transport *t,
+			   char *buf, unsigned int len)
+{
+	return DIV_ROUND_UP(get_buf_page_count(buf, len),
+			    t->pages_per_rw_credit);
 }
 
 static int smb_direct_create_header(struct smb_direct_transport *t,
@@ -1071,7 +1083,7 @@
 	int offset, len;
 	int i = 0;
 
-	if (nentries < get_buf_page_count(buf, size))
+	if (size <= 0 || nentries < get_buf_page_count(buf, size))
 		return -EINVAL;
 
 	offset = offset_in_page(buf);
@@ -1103,7 +1115,7 @@
 	int npages;
 
 	npages = get_sg_list(buf, size, sg_list, nentries);
-	if (npages <= 0)
+	if (npages < 0)
 		return -EINVAL;
 	return ib_dma_map_sg(device, sg_list, npages, dir);
 }
@@ -1229,14 +1241,12 @@
 
 	//FIXME: skip RFC1002 header..
 	buflen -= 4;
-	iov[0].iov_base += 4;
-	iov[0].iov_len -= 4;
 
 	remaining_data_length = buflen;
 	ksmbd_debug(RDMA, "Sending smb (RDMA): smb_len=%u\n", buflen);
 
 	smb_direct_send_ctx_init(st, &send_ctx, need_invalidate, remote_key);
-	start = i = 0;
+	start = i = 1;
 	buflen = 0;
 	while (true) {
 		buflen += iov[i].iov_len;
@@ -1298,11 +1308,21 @@
 	 * that means all the I/Os have been out and we are good to return
 	 */
 
-	wait_event(st->wait_send_payload_pending,
-		   atomic_read(&st->send_payload_pending) == 0);
+	wait_event(st->wait_send_pending,
+		   atomic_read(&st->send_pending) == 0);
 	return ret;
 }
 
+static void smb_direct_free_rdma_rw_msg(struct smb_direct_transport *t,
+					struct smb_direct_rdma_rw_msg *msg,
+					enum dma_data_direction dir)
+{
+	rdma_rw_ctx_destroy(&msg->rw_ctx, t->qp, t->qp->port,
+			    msg->sgt.sgl, msg->sgt.nents, dir);
+	sg_free_table_chained(&msg->sgt, SG_CHUNK_SIZE);
+	kfree(msg);
+}
+
 static void read_write_done(struct ib_cq *cq, struct ib_wc *wc,
 			    enum dma_data_direction dir)
 {
@@ -1311,19 +1331,14 @@
 	struct smb_direct_transport *t = msg->t;
 
 	if (wc->status != IB_WC_SUCCESS) {
+		msg->status = -EIO;
 		pr_err("read/write error. opcode = %d, status = %s(%d)\n",
 		       wc->opcode, ib_wc_status_msg(wc->status), wc->status);
-		smb_direct_disconnect_rdma_connection(t);
+		if (wc->status != IB_WC_WR_FLUSH_ERR)
+			smb_direct_disconnect_rdma_connection(t);
 	}
 
-	if (atomic_inc_return(&t->rw_avail_ops) > 0)
-		wake_up(&t->wait_rw_avail_ops);
-
-	rdma_rw_ctx_destroy(&msg->rw_ctx, t->qp, t->qp->port,
-			    msg->sg_list, msg->sgt.nents, dir);
-	sg_free_table_chained(&msg->sgt, SG_CHUNK_SIZE);
 	complete(msg->completion);
-	kfree(msg);
 }
 
 static void read_done(struct ib_cq *cq, struct ib_wc *wc)
@@ -1336,94 +1351,152 @@
 	read_write_done(cq, wc, DMA_TO_DEVICE);
 }
 
-static int smb_direct_rdma_xmit(struct smb_direct_transport *t, void *buf,
-				int buf_len, u32 remote_key, u64 remote_offset,
-				u32 remote_len, bool is_read)
+static int smb_direct_rdma_xmit(struct smb_direct_transport *t,
+				void *buf, int buf_len,
+				struct smb2_buffer_desc_v1 *desc,
+				unsigned int desc_len,
+				bool is_read)
 {
-	struct smb_direct_rdma_rw_msg *msg;
-	int ret;
+	struct smb_direct_rdma_rw_msg *msg, *next_msg;
+	int i, ret;
 	DECLARE_COMPLETION_ONSTACK(completion);
-	struct ib_send_wr *first_wr = NULL;
+	struct ib_send_wr *first_wr;
+	LIST_HEAD(msg_list);
+	char *desc_buf;
+	int credits_needed;
+	unsigned int desc_buf_len, desc_num = 0;
+
+	if (t->status != SMB_DIRECT_CS_CONNECTED)
+		return -ENOTCONN;
+
+	if (buf_len > t->max_rdma_rw_size)
+		return -EINVAL;
 
-	ret = wait_for_credits(t, &t->wait_rw_avail_ops, &t->rw_avail_ops);
+	/* calculate needed credits */
+	credits_needed = 0;
+	desc_buf = buf;
+	for (i = 0; i < desc_len / sizeof(*desc); i++) {
+		if (!buf_len)
+			break;
+
+		desc_buf_len = le32_to_cpu(desc[i].length);
+		if (!desc_buf_len)
+			return -EINVAL;
+
+		if (desc_buf_len > buf_len) {
+			desc_buf_len = buf_len;
+			desc[i].length = cpu_to_le32(desc_buf_len);
+			buf_len = 0;
+		}
+
+		credits_needed += calc_rw_credits(t, desc_buf, desc_buf_len);
+		desc_buf += desc_buf_len;
+		buf_len -= desc_buf_len;
+		desc_num++;
+	}
+
+	ksmbd_debug(RDMA, "RDMA %s, len %#x, needed credits %#x\n",
+		    is_read ? "read" : "write", buf_len, credits_needed);
+
+	ret = wait_for_rw_credits(t, credits_needed);
 	if (ret < 0)
 		return ret;
 
-	/* TODO: mempool */
-	msg = kmalloc(offsetof(struct smb_direct_rdma_rw_msg, sg_list) +
-		      sizeof(struct scatterlist) * SG_CHUNK_SIZE, GFP_KERNEL);
-	if (!msg) {
-		atomic_inc(&t->rw_avail_ops);
-		return -ENOMEM;
-	}
+	/* build rdma_rw_ctx for each descriptor */
+	desc_buf = buf;
+	for (i = 0; i < desc_num; i++) {
+		msg = kzalloc(offsetof(struct smb_direct_rdma_rw_msg, sg_list) +
+			      sizeof(struct scatterlist) * SG_CHUNK_SIZE, GFP_KERNEL);
+		if (!msg) {
+			ret = -ENOMEM;
+			goto out;
+		}
 
-	msg->sgt.sgl = &msg->sg_list[0];
-	ret = sg_alloc_table_chained(&msg->sgt,
-				     get_buf_page_count(buf, buf_len),
-				     msg->sg_list, SG_CHUNK_SIZE);
-	if (ret) {
-		atomic_inc(&t->rw_avail_ops);
-		kfree(msg);
-		return -ENOMEM;
-	}
+		desc_buf_len = le32_to_cpu(desc[i].length);
 
-	ret = get_sg_list(buf, buf_len, msg->sgt.sgl, msg->sgt.orig_nents);
-	if (ret <= 0) {
-		pr_err("failed to get pages\n");
-		goto err;
-	}
+		msg->t = t;
+		msg->cqe.done = is_read ? read_done : write_done;
+		msg->completion = &completion;
+
+		msg->sgt.sgl = &msg->sg_list[0];
+		ret = sg_alloc_table_chained(&msg->sgt,
+					     get_buf_page_count(desc_buf, desc_buf_len),
+					     msg->sg_list, SG_CHUNK_SIZE);
+		if (ret) {
+			kfree(msg);
+			ret = -ENOMEM;
+			goto out;
+		}
 
-	ret = rdma_rw_ctx_init(&msg->rw_ctx, t->qp, t->qp->port,
-			       msg->sg_list, get_buf_page_count(buf, buf_len),
-			       0, remote_offset, remote_key,
-			       is_read ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
-	if (ret < 0) {
-		pr_err("failed to init rdma_rw_ctx: %d\n", ret);
-		goto err;
+		ret = get_sg_list(desc_buf, desc_buf_len,
+				  msg->sgt.sgl, msg->sgt.orig_nents);
+		if (ret < 0) {
+			sg_free_table_chained(&msg->sgt, SG_CHUNK_SIZE);
+			kfree(msg);
+			goto out;
+		}
+
+		ret = rdma_rw_ctx_init(&msg->rw_ctx, t->qp, t->qp->port,
+				       msg->sgt.sgl,
+				       get_buf_page_count(desc_buf, desc_buf_len),
+				       0,
+				       le64_to_cpu(desc[i].offset),
+				       le32_to_cpu(desc[i].token),
+				       is_read ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
+		if (ret < 0) {
+			pr_err("failed to init rdma_rw_ctx: %d\n", ret);
+			sg_free_table_chained(&msg->sgt, SG_CHUNK_SIZE);
+			kfree(msg);
+			goto out;
+		}
+
+		list_add_tail(&msg->list, &msg_list);
+		desc_buf += desc_buf_len;
 	}
 
-	msg->t = t;
-	msg->cqe.done = is_read ? read_done : write_done;
-	msg->completion = &completion;
-	first_wr = rdma_rw_ctx_wrs(&msg->rw_ctx, t->qp, t->qp->port,
-				   &msg->cqe, NULL);
+	/* concatenate work requests of rdma_rw_ctxs */
+	first_wr = NULL;
+	list_for_each_entry_reverse(msg, &msg_list, list) {
+		first_wr = rdma_rw_ctx_wrs(&msg->rw_ctx, t->qp, t->qp->port,
+					   &msg->cqe, first_wr);
+	}
 
 	ret = ib_post_send(t->qp, first_wr, NULL);
 	if (ret) {
-		pr_err("failed to post send wr: %d\n", ret);
-		goto err;
+		pr_err("failed to post send wr for RDMA R/W: %d\n", ret);
+		goto out;
 	}
 
+	msg = list_last_entry(&msg_list, struct smb_direct_rdma_rw_msg, list);
 	wait_for_completion(&completion);
-	return 0;
-
-err:
-	atomic_inc(&t->rw_avail_ops);
-	if (first_wr)
-		rdma_rw_ctx_destroy(&msg->rw_ctx, t->qp, t->qp->port,
-				    msg->sg_list, msg->sgt.nents,
-				    is_read ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
-	sg_free_table_chained(&msg->sgt, SG_CHUNK_SIZE);
-	kfree(msg);
+	ret = msg->status;
+out:
+	list_for_each_entry_safe(msg, next_msg, &msg_list, list) {
+		list_del(&msg->list);
+		smb_direct_free_rdma_rw_msg(t, msg,
+					    is_read ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
+	}
+	atomic_add(credits_needed, &t->rw_credits);
+	wake_up(&t->wait_rw_credits);
 	return ret;
 }
 
-static int smb_direct_rdma_write(struct ksmbd_transport *t, void *buf,
-				 unsigned int buflen, u32 remote_key,
-				 u64 remote_offset, u32 remote_len)
+static int smb_direct_rdma_write(struct ksmbd_transport *t,
+				 void *buf, unsigned int buflen,
+				 struct smb2_buffer_desc_v1 *desc,
+				 unsigned int desc_len)
 {
 	return smb_direct_rdma_xmit(smb_trans_direct_transfort(t), buf, buflen,
-				    remote_key, remote_offset,
-				    remote_len, false);
+				    desc, desc_len, false);
 }
 
-static int smb_direct_rdma_read(struct ksmbd_transport *t, void *buf,
-				unsigned int buflen, u32 remote_key,
-				u64 remote_offset, u32 remote_len)
+static int smb_direct_rdma_read(struct ksmbd_transport *t,
+				void *buf, unsigned int buflen,
+				struct smb2_buffer_desc_v1 *desc,
+				unsigned int desc_len)
 {
 	return smb_direct_rdma_xmit(smb_trans_direct_transfort(t), buf, buflen,
-				    remote_key, remote_offset,
-				    remote_len, true);
+				    desc, desc_len, true);
 }
 
 static void smb_direct_disconnect(struct ksmbd_transport *t)
@@ -1438,6 +1511,15 @@
 	free_transport(st);
 }
 
+static void smb_direct_shutdown(struct ksmbd_transport *t)
+{
+	struct smb_direct_transport *st = smb_trans_direct_transfort(t);
+
+	ksmbd_debug(RDMA, "smb-direct shutdown cm_id=%p\n", st->cm_id);
+
+	smb_direct_disconnect_rdma_work(&st->disconnect_work);
+}
+
 static int smb_direct_cm_handler(struct rdma_cm_id *cm_id,
 				 struct rdma_cm_event *event)
 {
@@ -1454,6 +1536,8 @@
 	}
 	case RDMA_CM_EVENT_DEVICE_REMOVAL:
 	case RDMA_CM_EVENT_DISCONNECTED: {
+		ib_drain_qp(t->qp);
+
 		t->status = SMB_DIRECT_CS_DISCONNECTED;
 		wake_up_interruptible(&t->wait_status);
 		wake_up_interruptible(&t->wait_reassembly_queue);
@@ -1581,19 +1665,13 @@
 		pr_err("error at rdma_accept: %d\n", ret);
 		return ret;
 	}
-
-	wait_event_interruptible(t->wait_status,
-				 t->status != SMB_DIRECT_CS_NEW);
-	if (t->status != SMB_DIRECT_CS_CONNECTED)
-		return -ENOTCONN;
 	return 0;
 }
 
-static int smb_direct_negotiate(struct smb_direct_transport *t)
+static int smb_direct_prepare_negotiation(struct smb_direct_transport *t)
 {
 	int ret;
 	struct smb_direct_recvmsg *recvmsg;
-	struct smb_direct_negotiate_req *req;
 
 	recvmsg = get_free_recvmsg(t);
 	if (!recvmsg)
@@ -1603,82 +1681,74 @@
 	ret = smb_direct_post_recv(t, recvmsg);
 	if (ret) {
 		pr_err("Can't post recv: %d\n", ret);
-		goto out;
+		goto out_err;
 	}
 
 	t->negotiation_requested = false;
 	ret = smb_direct_accept_client(t);
 	if (ret) {
 		pr_err("Can't accept client\n");
-		goto out;
+		goto out_err;
 	}
 
 	smb_direct_post_recv_credits(&t->post_recv_credits_work.work);
-
-	ksmbd_debug(RDMA, "Waiting for SMB_DIRECT negotiate request\n");
-	ret = wait_event_interruptible_timeout(t->wait_status,
-					       t->negotiation_requested ||
-						t->status == SMB_DIRECT_CS_DISCONNECTED,
-					       SMB_DIRECT_NEGOTIATE_TIMEOUT * HZ);
-	if (ret <= 0 || t->status == SMB_DIRECT_CS_DISCONNECTED) {
-		ret = ret < 0 ? ret : -ETIMEDOUT;
-		goto out;
-	}
-
-	ret = smb_direct_check_recvmsg(recvmsg);
-	if (ret == -ECONNABORTED)
-		goto out;
-
-	req = (struct smb_direct_negotiate_req *)recvmsg->packet;
-	t->max_recv_size = min_t(int, t->max_recv_size,
-				 le32_to_cpu(req->preferred_send_size));
-	t->max_send_size = min_t(int, t->max_send_size,
-				 le32_to_cpu(req->max_receive_size));
-	t->max_fragmented_send_size =
-			le32_to_cpu(req->max_fragmented_size);
-
-	ret = smb_direct_send_negotiate_response(t, ret);
-out:
-	if (recvmsg)
-		put_recvmsg(t, recvmsg);
+	return 0;
+out_err:
+	put_recvmsg(t, recvmsg);
 	return ret;
 }
 
+static unsigned int smb_direct_get_max_fr_pages(struct smb_direct_transport *t)
+{
+	return min_t(unsigned int,
+		     t->cm_id->device->attrs.max_fast_reg_page_list_len,
+		     256);
+}
+
 static int smb_direct_init_params(struct smb_direct_transport *t,
 				  struct ib_qp_cap *cap)
 {
 	struct ib_device *device = t->cm_id->device;
-	int max_send_sges, max_pages, max_rw_wrs, max_send_wrs;
+	int max_send_sges, max_rw_wrs, max_send_wrs;
+	unsigned int max_sge_per_wr, wrs_per_credit;
 
-	/* need 2 more sge. because a SMB_DIRECT header will be mapped,
-	 * and maybe a send buffer could be not page aligned.
+	/* need 3 more sge. because a SMB_DIRECT header, SMB2 header,
+	 * SMB2 response could be mapped.
 	 */
 	t->max_send_size = smb_direct_max_send_size;
-	max_send_sges = DIV_ROUND_UP(t->max_send_size, PAGE_SIZE) + 2;
+	max_send_sges = DIV_ROUND_UP(t->max_send_size, PAGE_SIZE) + 3;
 	if (max_send_sges > SMB_DIRECT_MAX_SEND_SGES) {
 		pr_err("max_send_size %d is too large\n", t->max_send_size);
 		return -EINVAL;
 	}
 
-	/*
-	 * allow smb_direct_max_outstanding_rw_ops of in-flight RDMA
-	 * read/writes. HCA guarantees at least max_send_sge of sges for
-	 * a RDMA read/write work request, and if memory registration is used,
-	 * we need reg_mr, local_inv wrs for each read/write.
+	/* Calculate the number of work requests for RDMA R/W.
+	 * The maximum number of pages which can be registered
+	 * with one Memory region can be transferred with one
+	 * R/W credit. And at least 4 work requests for each credit
+	 * are needed for MR registration, RDMA R/W, local & remote
+	 * MR invalidation.
 	 */
 	t->max_rdma_rw_size = smb_direct_max_read_write_size;
-	max_pages = DIV_ROUND_UP(t->max_rdma_rw_size, PAGE_SIZE) + 1;
-	max_rw_wrs = DIV_ROUND_UP(max_pages, SMB_DIRECT_MAX_SEND_SGES);
-	max_rw_wrs += rdma_rw_mr_factor(device, t->cm_id->port_num,
-			max_pages) * 2;
-	max_rw_wrs *= smb_direct_max_outstanding_rw_ops;
+	t->pages_per_rw_credit = smb_direct_get_max_fr_pages(t);
+	t->max_rw_credits = DIV_ROUND_UP(t->max_rdma_rw_size,
+					 (t->pages_per_rw_credit - 1) *
+					 PAGE_SIZE);
+
+	max_sge_per_wr = min_t(unsigned int, device->attrs.max_send_sge,
+			       device->attrs.max_sge_rd);
+	max_sge_per_wr = max_t(unsigned int, max_sge_per_wr,
+			       max_send_sges);
+	wrs_per_credit = max_t(unsigned int, 4,
+			       DIV_ROUND_UP(t->pages_per_rw_credit,
+					    max_sge_per_wr) + 1);
+	max_rw_wrs = t->max_rw_credits * wrs_per_credit;
 
 	max_send_wrs = smb_direct_send_credit_target + max_rw_wrs;
 	if (max_send_wrs > device->attrs.max_cqe ||
 	    max_send_wrs > device->attrs.max_qp_wr) {
-		pr_err("consider lowering send_credit_target = %d, or max_outstanding_rw_ops = %d\n",
-		       smb_direct_send_credit_target,
-		       smb_direct_max_outstanding_rw_ops);
+		pr_err("consider lowering send_credit_target = %d\n",
+		       smb_direct_send_credit_target);
 		pr_err("Possible CQE overrun, device reporting max_cqe %d max_qp_wr %d\n",
 		       device->attrs.max_cqe, device->attrs.max_qp_wr);
 		return -EINVAL;
@@ -1693,11 +1763,6 @@
 		return -EINVAL;
 	}
 
-	if (device->attrs.max_send_sge < SMB_DIRECT_MAX_SEND_SGES) {
-		pr_err("warning: device max_send_sge = %d too small\n",
-		       device->attrs.max_send_sge);
-		return -EINVAL;
-	}
 	if (device->attrs.max_recv_sge < SMB_DIRECT_MAX_RECV_SGES) {
 		pr_err("warning: device max_recv_sge = %d too small\n",
 		       device->attrs.max_recv_sge);
@@ -1713,7 +1778,7 @@
 
 	t->send_credit_target = smb_direct_send_credit_target;
 	atomic_set(&t->send_credits, 0);
-	atomic_set(&t->rw_avail_ops, smb_direct_max_outstanding_rw_ops);
+	atomic_set(&t->rw_credits, t->max_rw_credits);
 
 	t->max_send_size = smb_direct_max_send_size;
 	t->max_recv_size = smb_direct_max_receive_size;
@@ -1721,10 +1786,10 @@
 
 	cap->max_send_wr = max_send_wrs;
 	cap->max_recv_wr = t->recv_credit_max;
-	cap->max_send_sge = SMB_DIRECT_MAX_SEND_SGES;
+	cap->max_send_sge = max_sge_per_wr;
 	cap->max_recv_sge = SMB_DIRECT_MAX_RECV_SGES;
 	cap->max_inline_data = 0;
-	cap->max_rdma_ctxs = 0;
+	cap->max_rdma_ctxs = t->max_rw_credits;
 	return 0;
 }
 
@@ -1806,6 +1871,7 @@
 {
 	int ret;
 	struct ib_qp_init_attr qp_attr;
+	int pages_per_rw;
 
 	t->pd = ib_alloc_pd(t->cm_id->device, 0);
 	if (IS_ERR(t->pd)) {
@@ -1816,7 +1882,8 @@
 	}
 
 	t->send_cq = ib_alloc_cq(t->cm_id->device, t,
-				 t->send_credit_target, 0, IB_POLL_WORKQUEUE);
+				 smb_direct_send_credit_target + cap->max_rdma_ctxs,
+				 0, IB_POLL_WORKQUEUE);
 	if (IS_ERR(t->send_cq)) {
 		pr_err("Can't create RDMA send CQ\n");
 		ret = PTR_ERR(t->send_cq);
@@ -1825,8 +1892,7 @@
 	}
 
 	t->recv_cq = ib_alloc_cq(t->cm_id->device, t,
-				 cap->max_send_wr + cap->max_rdma_ctxs,
-				 0, IB_POLL_WORKQUEUE);
+				 t->recv_credit_max, 0, IB_POLL_WORKQUEUE);
 	if (IS_ERR(t->recv_cq)) {
 		pr_err("Can't create RDMA recv CQ\n");
 		ret = PTR_ERR(t->recv_cq);
@@ -1853,6 +1919,18 @@
 	t->qp = t->cm_id->qp;
 	t->cm_id->event_handler = smb_direct_cm_handler;
 
+	pages_per_rw = DIV_ROUND_UP(t->max_rdma_rw_size, PAGE_SIZE) + 1;
+	if (pages_per_rw > t->cm_id->device->attrs.max_sgl_rd) {
+		ret = ib_mr_pool_init(t->qp, &t->qp->rdma_mrs,
+				      t->max_rw_credits, IB_MR_TYPE_MEM_REG,
+				      t->pages_per_rw_credit, 0);
+		if (ret) {
+			pr_err("failed to init mr pool count %d pages %d\n",
+			       t->max_rw_credits, t->pages_per_rw_credit);
+			goto err;
+		}
+	}
+
 	return 0;
 err:
 	if (t->qp) {
@@ -1877,6 +1955,49 @@
 static int smb_direct_prepare(struct ksmbd_transport *t)
 {
 	struct smb_direct_transport *st = smb_trans_direct_transfort(t);
+	struct smb_direct_recvmsg *recvmsg;
+	struct smb_direct_negotiate_req *req;
+	int ret;
+
+	ksmbd_debug(RDMA, "Waiting for SMB_DIRECT negotiate request\n");
+	ret = wait_event_interruptible_timeout(st->wait_status,
+					       st->negotiation_requested ||
+					       st->status == SMB_DIRECT_CS_DISCONNECTED,
+					       SMB_DIRECT_NEGOTIATE_TIMEOUT * HZ);
+	if (ret <= 0 || st->status == SMB_DIRECT_CS_DISCONNECTED)
+		return ret < 0 ? ret : -ETIMEDOUT;
+
+	recvmsg = get_first_reassembly(st);
+	if (!recvmsg)
+		return -ECONNABORTED;
+
+	ret = smb_direct_check_recvmsg(recvmsg);
+	if (ret == -ECONNABORTED)
+		goto out;
+
+	req = (struct smb_direct_negotiate_req *)recvmsg->packet;
+	st->max_recv_size = min_t(int, st->max_recv_size,
+				  le32_to_cpu(req->preferred_send_size));
+	st->max_send_size = min_t(int, st->max_send_size,
+				  le32_to_cpu(req->max_receive_size));
+	st->max_fragmented_send_size =
+		le32_to_cpu(req->max_fragmented_size);
+	st->max_fragmented_recv_size =
+		(st->recv_credit_max * st->max_recv_size) / 2;
+
+	ret = smb_direct_send_negotiate_response(st, ret);
+out:
+	spin_lock_irq(&st->reassembly_queue_lock);
+	st->reassembly_queue_length--;
+	list_del(&recvmsg->list);
+	spin_unlock_irq(&st->reassembly_queue_lock);
+	put_recvmsg(st, recvmsg);
+
+	return ret;
+}
+
+static int smb_direct_connect(struct smb_direct_transport *st)
+{
 	int ret;
 	struct ib_qp_cap qp_cap;
 
@@ -1898,13 +2019,11 @@
 		return ret;
 	}
 
-	ret = smb_direct_negotiate(st);
+	ret = smb_direct_prepare_negotiation(st);
 	if (ret) {
 		pr_err("Can't negotiate: %d\n", ret);
 		return ret;
 	}
-
-	st->status = SMB_DIRECT_CS_CONNECTED;
 	return 0;
 }
 
@@ -1920,6 +2039,8 @@
 static int smb_direct_handle_connect_request(struct rdma_cm_id *new_cm_id)
 {
 	struct smb_direct_transport *t;
+	struct task_struct *handler;
+	int ret;
 
 	if (!rdma_frwr_is_supported(&new_cm_id->device->attrs)) {
 		ksmbd_debug(RDMA,
@@ -1932,18 +2053,23 @@
 	if (!t)
 		return -ENOMEM;
 
-	KSMBD_TRANS(t)->handler = kthread_run(ksmbd_conn_handler_loop,
-					      KSMBD_TRANS(t)->conn, "ksmbd:r%u",
-					      SMB_DIRECT_PORT);
-	if (IS_ERR(KSMBD_TRANS(t)->handler)) {
-		int ret = PTR_ERR(KSMBD_TRANS(t)->handler);
+	ret = smb_direct_connect(t);
+	if (ret)
+		goto out_err;
 
+	handler = kthread_run(ksmbd_conn_handler_loop,
+			      KSMBD_TRANS(t)->conn, "ksmbd:r%u",
+			      smb_direct_port);
+	if (IS_ERR(handler)) {
+		ret = PTR_ERR(handler);
 		pr_err("Can't start thread\n");
-		free_transport(t);
-		return ret;
+		goto out_err;
 	}
 
 	return 0;
+out_err:
+	free_transport(t);
+	return ret;
 }
 
 static int smb_direct_listen_handler(struct rdma_cm_id *cm_id,
@@ -2007,12 +2133,64 @@
 	return ret;
 }
 
+static int smb_direct_ib_client_add(struct ib_device *ib_dev)
+{
+	struct smb_direct_device *smb_dev;
+
+	/* Set 5445 port if device type is iWARP(No IB) */
+	if (ib_dev->node_type != RDMA_NODE_IB_CA)
+		smb_direct_port = SMB_DIRECT_PORT_IWARP;
+
+	if (!rdma_frwr_is_supported(&ib_dev->attrs))
+		return 0;
+
+	smb_dev = kzalloc(sizeof(*smb_dev), GFP_KERNEL);
+	if (!smb_dev)
+		return -ENOMEM;
+	smb_dev->ib_dev = ib_dev;
+
+	write_lock(&smb_direct_device_lock);
+	list_add(&smb_dev->list, &smb_direct_device_list);
+	write_unlock(&smb_direct_device_lock);
+
+	ksmbd_debug(RDMA, "ib device added: name %s\n", ib_dev->name);
+	return 0;
+}
+
+static void smb_direct_ib_client_remove(struct ib_device *ib_dev,
+					void *client_data)
+{
+	struct smb_direct_device *smb_dev, *tmp;
+
+	write_lock(&smb_direct_device_lock);
+	list_for_each_entry_safe(smb_dev, tmp, &smb_direct_device_list, list) {
+		if (smb_dev->ib_dev == ib_dev) {
+			list_del(&smb_dev->list);
+			kfree(smb_dev);
+			break;
+		}
+	}
+	write_unlock(&smb_direct_device_lock);
+}
+
+static struct ib_client smb_direct_ib_client = {
+	.name	= "ksmbd_smb_direct_ib",
+	.add	= smb_direct_ib_client_add,
+	.remove	= smb_direct_ib_client_remove,
+};
+
 int ksmbd_rdma_init(void)
 {
 	int ret;
 
 	smb_direct_listener.cm_id = NULL;
 
+	ret = ib_register_client(&smb_direct_ib_client);
+	if (ret) {
+		pr_err("failed to ib_register_client\n");
+		return ret;
+	}
+
 	/* When a client is running out of send credits, the credits are
 	 * granted by the server's sending a packet using this queue.
 	 * This avoids the situation that a clients cannot send packets
@@ -2023,7 +2201,7 @@
 	if (!smb_direct_wq)
 		return -ENOMEM;
 
-	ret = smb_direct_listen(SMB_DIRECT_PORT);
+	ret = smb_direct_listen(smb_direct_port);
 	if (ret) {
 		destroy_workqueue(smb_direct_wq);
 		smb_direct_wq = NULL;
@@ -2036,37 +2214,88 @@
 	return 0;
 }
 
-int ksmbd_rdma_destroy(void)
+void ksmbd_rdma_destroy(void)
 {
-	if (smb_direct_listener.cm_id)
-		rdma_destroy_id(smb_direct_listener.cm_id);
+	if (!smb_direct_listener.cm_id)
+		return;
+
+	ib_unregister_client(&smb_direct_ib_client);
+	rdma_destroy_id(smb_direct_listener.cm_id);
+
 	smb_direct_listener.cm_id = NULL;
 
 	if (smb_direct_wq) {
-		flush_workqueue(smb_direct_wq);
 		destroy_workqueue(smb_direct_wq);
 		smb_direct_wq = NULL;
 	}
-	return 0;
 }
 
 bool ksmbd_rdma_capable_netdev(struct net_device *netdev)
 {
-	struct ib_device *ibdev;
+	struct smb_direct_device *smb_dev;
+	int i;
 	bool rdma_capable = false;
 
-	ibdev = ib_device_get_by_netdev(netdev, RDMA_DRIVER_UNKNOWN);
-	if (ibdev) {
-		if (rdma_frwr_is_supported(&ibdev->attrs))
-			rdma_capable = true;
-		ib_device_put(ibdev);
+	read_lock(&smb_direct_device_lock);
+	list_for_each_entry(smb_dev, &smb_direct_device_list, list) {
+		for (i = 0; i < smb_dev->ib_dev->phys_port_cnt; i++) {
+			struct net_device *ndev;
+
+			if (smb_dev->ib_dev->ops.get_netdev) {
+				ndev = smb_dev->ib_dev->ops.get_netdev(
+					smb_dev->ib_dev, i + 1);
+				if (!ndev)
+					continue;
+
+				if (ndev == netdev) {
+					dev_put(ndev);
+					rdma_capable = true;
+					goto out;
+				}
+				dev_put(ndev);
+			/* if ib_dev does not implement ops.get_netdev
+			 * check for matching infiniband GUID in hw_addr
+			 */
+			} else if (netdev->type == ARPHRD_INFINIBAND) {
+				struct netdev_hw_addr *ha;
+				union ib_gid gid;
+				u32 port_num;
+				int ret;
+
+				netdev_hw_addr_list_for_each(
+					ha, &netdev->dev_addrs) {
+					memcpy(&gid, ha->addr + 4, sizeof(gid));
+					ret = ib_find_gid(smb_dev->ib_dev, &gid,
+							  &port_num, NULL);
+					if (!ret) {
+						rdma_capable = true;
+						goto out;
+					}
+				}
+			}
+		}
+	}
+out:
+	read_unlock(&smb_direct_device_lock);
+
+	if (rdma_capable == false) {
+		struct ib_device *ibdev;
+
+		ibdev = ib_device_get_by_netdev(netdev, RDMA_DRIVER_UNKNOWN);
+		if (ibdev) {
+			if (rdma_frwr_is_supported(&ibdev->attrs))
+				rdma_capable = true;
+			ib_device_put(ibdev);
+		}
 	}
+
 	return rdma_capable;
 }
 
 static struct ksmbd_transport_ops ksmbd_smb_direct_transport_ops = {
 	.prepare	= smb_direct_prepare,
 	.disconnect	= smb_direct_disconnect,
+	.shutdown	= smb_direct_shutdown,
 	.writev		= smb_direct_writev,
 	.read		= smb_direct_read,
 	.rdma_read	= smb_direct_rdma_read,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/transport_rdma.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/transport_rdma.h
@@ -7,7 +7,9 @@
 #ifndef __KSMBD_TRANSPORT_RDMA_H__
 #define __KSMBD_TRANSPORT_RDMA_H__
 
-#define SMB_DIRECT_PORT	5445
+#define SMBD_DEFAULT_IOSIZE (8 * 1024 * 1024)
+#define SMBD_MIN_IOSIZE (512 * 1024)
+#define SMBD_MAX_IOSIZE (16 * 1024 * 1024)
 
 /* SMB DIRECT negotiation request packet [MS-SMBD] 2.2.1 */
 struct smb_direct_negotiate_req {
@@ -52,12 +54,16 @@
 
 #ifdef CONFIG_SMB_SERVER_SMBDIRECT
 int ksmbd_rdma_init(void);
-int ksmbd_rdma_destroy(void);
+void ksmbd_rdma_destroy(void);
 bool ksmbd_rdma_capable_netdev(struct net_device *netdev);
+void init_smbd_max_io_size(unsigned int sz);
+unsigned int get_smbd_max_read_write_size(void);
 #else
 static inline int ksmbd_rdma_init(void) { return 0; }
 static inline int ksmbd_rdma_destroy(void) { return 0; }
 static inline bool ksmbd_rdma_capable_netdev(struct net_device *netdev) { return false; }
+static inline void init_smbd_max_io_size(unsigned int sz) { }
+static inline unsigned int get_smbd_max_read_write_size(void) { return 0; }
 #endif
 
 #endif /* __KSMBD_TRANSPORT_RDMA_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/transport_tcp.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/transport_tcp.c
@@ -15,6 +15,8 @@
 #define IFACE_STATE_DOWN		BIT(0)
 #define IFACE_STATE_CONFIGURED		BIT(1)
 
+static atomic_t active_num_conn;
+
 struct interface {
 	struct task_struct	*ksmbd_kthread;
 	struct socket		*ksmbd_socket;
@@ -183,10 +185,13 @@
 	struct sockaddr *csin;
 	int rc = 0;
 	struct tcp_transport *t;
+	struct task_struct *handler;
 
 	t = alloc_transport(client_sk);
-	if (!t)
+	if (!t) {
+		sock_release(client_sk);
 		return -ENOMEM;
+	}
 
 	csin = KSMBD_TCP_PEER_SOCKADDR(KSMBD_TRANS(t)->conn);
 	if (kernel_getpeername(client_sk, csin) < 0) {
@@ -195,13 +200,13 @@
 		goto out_error;
 	}
 
-	KSMBD_TRANS(t)->handler = kthread_run(ksmbd_conn_handler_loop,
-					      KSMBD_TRANS(t)->conn,
-					      "ksmbd:%u",
-					      ksmbd_tcp_get_port(csin));
-	if (IS_ERR(KSMBD_TRANS(t)->handler)) {
+	handler = kthread_run(ksmbd_conn_handler_loop,
+			      KSMBD_TRANS(t)->conn,
+			      "ksmbd:%u",
+			      ksmbd_tcp_get_port(csin));
+	if (IS_ERR(handler)) {
 		pr_err("cannot start conn thread\n");
-		rc = PTR_ERR(KSMBD_TRANS(t)->handler);
+		rc = PTR_ERR(handler);
 		free_transport(t);
 	}
 	return rc;
@@ -230,7 +235,7 @@
 			break;
 		}
 		ret = kernel_accept(iface->ksmbd_socket, &client_sk,
-				    O_NONBLOCK);
+				    SOCK_NONBLOCK);
 		mutex_unlock(&iface->sock_release_lock);
 		if (ret) {
 			if (ret == -EAGAIN)
@@ -239,6 +244,15 @@
 			continue;
 		}
 
+		if (server_conf.max_connections &&
+		    atomic_inc_return(&active_num_conn) >= server_conf.max_connections) {
+			pr_info_ratelimited("Limit the maximum number of connections(%u)\n",
+					    atomic_read(&active_num_conn));
+			atomic_dec(&active_num_conn);
+			sock_release(client_sk);
+			continue;
+		}
+
 		ksmbd_debug(CONN, "connect success: accepted new connection\n");
 		client_sk->sk->sk_rcvtimeo = KSMBD_TCP_RECV_TIMEOUT;
 		client_sk->sk->sk_sndtimeo = KSMBD_TCP_SEND_TIMEOUT;
@@ -278,16 +292,18 @@
 
 /**
  * ksmbd_tcp_readv() - read data from socket in given iovec
- * @t:		TCP transport instance
- * @iov_orig:	base IO vector
- * @nr_segs:	number of segments in base iov
- * @to_read:	number of bytes to read from socket
+ * @t:			TCP transport instance
+ * @iov_orig:		base IO vector
+ * @nr_segs:		number of segments in base iov
+ * @to_read:		number of bytes to read from socket
+ * @max_retries:	maximum retry count
  *
  * Return:	on success return number of bytes read from socket,
  *		otherwise return error number
  */
 static int ksmbd_tcp_readv(struct tcp_transport *t, struct kvec *iov_orig,
-			   unsigned int nr_segs, unsigned int to_read)
+			   unsigned int nr_segs, unsigned int to_read,
+			   int max_retries)
 {
 	int length = 0;
 	int total_read;
@@ -318,15 +334,26 @@
 		if (length == -EINTR) {
 			total_read = -ESHUTDOWN;
 			break;
-		} else if (conn->status == KSMBD_SESS_NEED_RECONNECT) {
+		} else if (ksmbd_conn_need_reconnect(conn)) {
 			total_read = -EAGAIN;
 			break;
 		} else if (length == -ERESTARTSYS || length == -EAGAIN) {
+			/*
+			 * If max_retries is negative, Allow unlimited
+			 * retries to keep connection with inactive sessions.
+			 */
+			if (max_retries == 0) {
+				total_read = length;
+				break;
+			} else if (max_retries > 0) {
+				max_retries--;
+			}
+
 			usleep_range(1000, 2000);
 			length = 0;
 			continue;
 		} else if (length <= 0) {
-			total_read = -EAGAIN;
+			total_read = length;
 			break;
 		}
 	}
@@ -342,14 +369,15 @@
  * Return:	on success return number of bytes read from socket,
  *		otherwise return error number
  */
-static int ksmbd_tcp_read(struct ksmbd_transport *t, char *buf, unsigned int to_read)
+static int ksmbd_tcp_read(struct ksmbd_transport *t, char *buf,
+			  unsigned int to_read, int max_retries)
 {
 	struct kvec iov;
 
 	iov.iov_base = buf;
 	iov.iov_len = to_read;
 
-	return ksmbd_tcp_readv(TCP_TRANS(t), &iov, 1, to_read);
+	return ksmbd_tcp_readv(TCP_TRANS(t), &iov, 1, to_read, max_retries);
 }
 
 static int ksmbd_tcp_writev(struct ksmbd_transport *t, struct kvec *iov,
@@ -365,6 +393,8 @@
 static void ksmbd_tcp_disconnect(struct ksmbd_transport *t)
 {
 	free_transport(TCP_TRANS(t));
+	if (server_conf.max_connections)
+		atomic_dec(&active_num_conn);
 }
 
 static void tcp_destroy_socket(struct socket *ksmbd_socket)
@@ -399,12 +429,13 @@
 
 	ret = sock_create(PF_INET6, SOCK_STREAM, IPPROTO_TCP, &ksmbd_socket);
 	if (ret) {
-		pr_err("Can't create socket for ipv6, try ipv4: %d\n", ret);
+		if (ret != -EAFNOSUPPORT)
+			pr_err("Can't create socket for ipv6, fallback to ipv4: %d\n", ret);
 		ret = sock_create(PF_INET, SOCK_STREAM, IPPROTO_TCP,
 				  &ksmbd_socket);
 		if (ret) {
 			pr_err("Can't create socket for ipv4: %d\n", ret);
-			goto out_error;
+			goto out_clear;
 		}
 
 		sin.sin_family = PF_INET;
@@ -462,6 +493,7 @@
 
 out_error:
 	tcp_destroy_socket(ksmbd_socket);
+out_clear:
 	iface->ksmbd_socket = NULL;
 	return ret;
 }
@@ -475,7 +507,7 @@
 
 	switch (event) {
 	case NETDEV_UP:
-		if (netdev->priv_flags & IFF_BRIDGE_PORT)
+		if (netif_is_bridge_port(netdev))
 			return NOTIFY_OK;
 
 		list_for_each_entry(iface, &iface_list, entry) {
@@ -584,10 +616,12 @@
 
 		rtnl_lock();
 		for_each_netdev(&init_net, netdev) {
-			if (netdev->priv_flags & IFF_BRIDGE_PORT)
+			if (netif_is_bridge_port(netdev))
 				continue;
-			if (!alloc_iface(kstrdup(netdev->name, GFP_KERNEL)))
+			if (!alloc_iface(kstrdup(netdev->name, GFP_KERNEL))) {
+				rtnl_unlock();
 				return -ENOMEM;
+			}
 		}
 		rtnl_unlock();
 		bind_additional_ifaces = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/unicode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/unicode.c
@@ -15,45 +15,9 @@
 #include "smb_common.h"
 
 /*
- * smb_utf16_bytes() - how long will a string be after conversion?
- * @from:	pointer to input string
- * @maxbytes:	don't go past this many bytes of input string
- * @codepage:	destination codepage
- *
- * Walk a utf16le string and return the number of bytes that the string will
- * be after being converted to the given charset, not including any null
- * termination required. Don't walk past maxbytes in the source buffer.
- *
- * Return:	string length after conversion
- */
-static int smb_utf16_bytes(const __le16 *from, int maxbytes,
-			   const struct nls_table *codepage)
-{
-	int i;
-	int charlen, outlen = 0;
-	int maxwords = maxbytes / 2;
-	char tmp[NLS_MAX_CHARSET_SIZE];
-	__u16 ftmp;
-
-	for (i = 0; i < maxwords; i++) {
-		ftmp = get_unaligned_le16(&from[i]);
-		if (ftmp == 0)
-			break;
-
-		charlen = codepage->uni2char(ftmp, tmp, NLS_MAX_CHARSET_SIZE);
-		if (charlen > 0)
-			outlen += charlen;
-		else
-			outlen++;
-	}
-
-	return outlen;
-}
-
-/*
  * cifs_mapchar() - convert a host-endian char to proper char in codepage
  * @target:	where converted character should be copied
- * @src_char:	2 byte host-endian source character
+ * @from:	host-endian source string
  * @cp:		codepage to which character should be converted
  * @mapchar:	should character be mapped according to mapchars mount option?
  *
@@ -64,10 +28,13 @@
  * Return:	string length after conversion
  */
 static int
-cifs_mapchar(char *target, const __u16 src_char, const struct nls_table *cp,
+cifs_mapchar(char *target, const __u16 *from, const struct nls_table *cp,
 	     bool mapchar)
 {
 	int len = 1;
+	__u16 src_char;
+
+	src_char = *from;
 
 	if (!mapchar)
 		goto cp_convert;
@@ -105,30 +72,66 @@
 
 cp_convert:
 	len = cp->uni2char(src_char, target, NLS_MAX_CHARSET_SIZE);
-	if (len <= 0) {
-		*target = '?';
-		len = 1;
-	}
+	if (len <= 0)
+		goto surrogate_pair;
+
+	goto out;
+
+surrogate_pair:
+	/* convert SURROGATE_PAIR and IVS */
+	if (strcmp(cp->charset, "utf8"))
+		goto unknown;
+	len = utf16s_to_utf8s(from, 3, UTF16_LITTLE_ENDIAN, target, 6);
+	if (len <= 0)
+		goto unknown;
+	return len;
 
+unknown:
+	*target = '?';
+	len = 1;
 	goto out;
 }
 
 /*
- * is_char_allowed() - check for valid character
- * @ch:		input character to be checked
+ * smb_utf16_bytes() - compute converted string length
+ * @from:	pointer to input string
+ * @maxbytes:	input string length
+ * @codepage:	destination codepage
+ *
+ * Walk a utf16le string and return the number of bytes that the string will
+ * be after being converted to the given charset, not including any null
+ * termination required. Don't walk past maxbytes in the source buffer.
  *
- * Return:	1 if char is allowed, otherwise 0
+ * Return:	string length after conversion
  */
-static inline int is_char_allowed(char *ch)
+static int smb_utf16_bytes(const __le16 *from, int maxbytes,
+			   const struct nls_table *codepage)
 {
-	/* check for control chars, wildcards etc. */
-	if (!(*ch & 0x80) &&
-	    (*ch <= 0x1f ||
-	     *ch == '?' || *ch == '"' || *ch == '<' ||
-	     *ch == '>' || *ch == '|'))
-		return 0;
+	int i, j;
+	int charlen, outlen = 0;
+	int maxwords = maxbytes / 2;
+	char tmp[NLS_MAX_CHARSET_SIZE];
+	__u16 ftmp[3];
+
+	for (i = 0; i < maxwords; i++) {
+		ftmp[0] = get_unaligned_le16(&from[i]);
+		if (ftmp[0] == 0)
+			break;
+		for (j = 1; j <= 2; j++) {
+			if (i + j < maxwords)
+				ftmp[j] = get_unaligned_le16(&from[i + j]);
+			else
+				ftmp[j] = 0;
+		}
 
-	return 1;
+		charlen = cifs_mapchar(tmp, ftmp, codepage, 0);
+		if (charlen > 0)
+			outlen += charlen;
+		else
+			outlen++;
+	}
+
+	return outlen;
 }
 
 /*
@@ -158,12 +161,12 @@
 static int smb_from_utf16(char *to, const __le16 *from, int tolen, int fromlen,
 			  const struct nls_table *codepage, bool mapchar)
 {
-	int i, charlen, safelen;
+	int i, j, charlen, safelen;
 	int outlen = 0;
 	int nullsize = nls_nullsize(codepage);
 	int fromwords = fromlen / 2;
 	char tmp[NLS_MAX_CHARSET_SIZE];
-	__u16 ftmp;
+	__u16 ftmp[3];	/* ftmp[3] = 3array x 2bytes = 6bytes UTF-16 */
 
 	/*
 	 * because the chars can be of varying widths, we need to take care
@@ -174,9 +177,15 @@
 	safelen = tolen - (NLS_MAX_CHARSET_SIZE + nullsize);
 
 	for (i = 0; i < fromwords; i++) {
-		ftmp = get_unaligned_le16(&from[i]);
-		if (ftmp == 0)
+		ftmp[0] = get_unaligned_le16(&from[i]);
+		if (ftmp[0] == 0)
 			break;
+		for (j = 1; j <= 2; j++) {
+			if (i + j < fromwords)
+				ftmp[j] = get_unaligned_le16(&from[i + j]);
+			else
+				ftmp[j] = 0;
+		}
 
 		/*
 		 * check to see if converting this character might make the
@@ -191,6 +200,19 @@
 		/* put converted char into 'to' buffer */
 		charlen = cifs_mapchar(&to[outlen], ftmp, codepage, mapchar);
 		outlen += charlen;
+
+		/*
+		 * charlen (=bytes of UTF-8 for 1 character)
+		 * 4bytes UTF-8(surrogate pair) is charlen=4
+		 * (4bytes UTF-16 code)
+		 * 7-8bytes UTF-8(IVS) is charlen=3+4 or 4+4
+		 * (2 UTF-8 pairs divided to 2 UTF-16 pairs)
+		 */
+		if (charlen == 4)
+			i++;
+		else if (charlen >= 5)
+			/* 5-6bytes UTF-8 */
+			i += 2;
 	}
 
 	/* properly null-terminate string */
@@ -325,6 +347,9 @@
 	char src_char;
 	__le16 dst_char;
 	wchar_t tmp;
+	wchar_t wchar_to[6];	/* UTF-16 */
+	int ret;
+	unicode_t u;
 
 	if (!mapchars)
 		return smb_strtoUTF16(target, source, srclen, cp);
@@ -367,11 +392,57 @@
 			 * if no match, use question mark, which at least in
 			 * some cases serves as wild card
 			 */
-			if (charlen < 1) {
-				dst_char = cpu_to_le16(0x003f);
-				charlen = 1;
+			if (charlen > 0)
+				goto ctoUTF16;
+
+			/* convert SURROGATE_PAIR */
+			if (strcmp(cp->charset, "utf8"))
+				goto unknown;
+			if (*(source + i) & 0x80) {
+				charlen = utf8_to_utf32(source + i, 6, &u);
+				if (charlen < 0)
+					goto unknown;
+			} else
+				goto unknown;
+			ret  = utf8s_to_utf16s(source + i, charlen,
+					UTF16_LITTLE_ENDIAN,
+					wchar_to, 6);
+			if (ret < 0)
+				goto unknown;
+
+			i += charlen;
+			dst_char = cpu_to_le16(*wchar_to);
+			if (charlen <= 3)
+				/* 1-3bytes UTF-8 to 2bytes UTF-16 */
+				put_unaligned(dst_char, &target[j]);
+			else if (charlen == 4) {
+				/*
+				 * 4bytes UTF-8(surrogate pair) to 4bytes UTF-16
+				 * 7-8bytes UTF-8(IVS) divided to 2 UTF-16
+				 * (charlen=3+4 or 4+4)
+				 */
+				put_unaligned(dst_char, &target[j]);
+				dst_char = cpu_to_le16(*(wchar_to + 1));
+				j++;
+				put_unaligned(dst_char, &target[j]);
+			} else if (charlen >= 5) {
+				/* 5-6bytes UTF-8 to 6bytes UTF-16 */
+				put_unaligned(dst_char, &target[j]);
+				dst_char = cpu_to_le16(*(wchar_to + 1));
+				j++;
+				put_unaligned(dst_char, &target[j]);
+				dst_char = cpu_to_le16(*(wchar_to + 2));
+				j++;
+				put_unaligned(dst_char, &target[j]);
 			}
+			continue;
+
+unknown:
+			dst_char = cpu_to_le16(0x003f);
+			charlen = 1;
 		}
+
+ctoUTF16:
 		/*
 		 * character may take more than one byte in the source string,
 		 * but will take exactly two bytes in the target string
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/unicode.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/unicode.h
@@ -24,6 +24,7 @@
 #include <asm/byteorder.h>
 #include <linux/types.h>
 #include <linux/nls.h>
+#include <linux/unicode.h>
 
 #define  UNIUPR_NOLOWER		/* Example to not expand lower case tables */
 
@@ -69,7 +70,7 @@
 			     const struct nls_table *codepage);
 int smbConvertToUTF16(__le16 *target, const char *source, int srclen,
 		      const struct nls_table *cp, int mapchars);
-char *ksmbd_extract_sharename(char *treename);
+char *ksmbd_extract_sharename(struct unicode_map *um, const char *treename);
 #endif
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/vfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/vfs.c
@@ -18,8 +18,7 @@
 #include <linux/vmalloc.h>
 #include <linux/sched/xacct.h>
 #include <linux/crc32c.h>
-
-#include "../internal.h"	/* for vfs_path_lookup */
+#include <linux/namei.h>
 
 #include "glob.h"
 #include "oplock.h"
@@ -37,19 +36,6 @@
 #include "mgmt/user_session.h"
 #include "mgmt/user_config.h"
 
-static char *extract_last_component(char *path)
-{
-	char *p = strrchr(path, '/');
-
-	if (p && p[1] != '\0') {
-		*p = '\0';
-		p++;
-	} else {
-		p = NULL;
-	}
-	return p;
-}
-
 static void ksmbd_vfs_inherit_owner(struct ksmbd_work *work,
 				    struct inode *parent_inode,
 				    struct inode *inode)
@@ -63,67 +49,96 @@
 
 /**
  * ksmbd_vfs_lock_parent() - lock parent dentry if it is stable
- *
- * the parent dentry got by dget_parent or @parent could be
- * unstable, we try to lock a parent inode and lookup the
- * child dentry again.
- *
- * the reference count of @parent isn't incremented.
  */
-int ksmbd_vfs_lock_parent(struct user_namespace *user_ns, struct dentry *parent,
-			  struct dentry *child)
+int ksmbd_vfs_lock_parent(struct dentry *parent, struct dentry *child)
 {
-	struct dentry *dentry;
-	int ret = 0;
-
 	inode_lock_nested(d_inode(parent), I_MUTEX_PARENT);
-	dentry = lookup_one(user_ns, child->d_name.name, parent,
-			    child->d_name.len);
-	if (IS_ERR(dentry)) {
-		ret = PTR_ERR(dentry);
-		goto out_err;
-	}
-
-	if (dentry != child) {
-		ret = -ESTALE;
-		dput(dentry);
-		goto out_err;
+	if (child->d_parent != parent) {
+		inode_unlock(d_inode(parent));
+		return -ENOENT;
 	}
 
-	dput(dentry);
 	return 0;
-out_err:
-	inode_unlock(d_inode(parent));
-	return ret;
 }
 
-int ksmbd_vfs_may_delete(struct user_namespace *user_ns,
-			 struct dentry *dentry)
-{
-	struct dentry *parent;
-	int ret;
+static int ksmbd_vfs_path_lookup_locked(struct ksmbd_share_config *share_conf,
+					char *pathname, unsigned int flags,
+					struct path *parent_path,
+					struct path *path)
+{
+	struct qstr last;
+	struct filename *filename;
+	struct path *root_share_path = &share_conf->vfs_path;
+	int err, type;
+	struct dentry *d;
+
+	if (pathname[0] == '\0') {
+		pathname = share_conf->path;
+		root_share_path = NULL;
+	} else {
+		flags |= LOOKUP_BENEATH;
+	}
 
-	parent = dget_parent(dentry);
-	ret = ksmbd_vfs_lock_parent(user_ns, parent, dentry);
-	if (ret) {
-		dput(parent);
-		return ret;
+	filename = getname_kernel(pathname);
+	if (IS_ERR(filename))
+		return PTR_ERR(filename);
+
+	err = vfs_path_parent_lookup(filename, flags,
+				     parent_path, &last, &type,
+				     root_share_path);
+	if (err) {
+		putname(filename);
+		return err;
 	}
 
-	ret = inode_permission(user_ns, d_inode(parent),
-			       MAY_EXEC | MAY_WRITE);
+	if (unlikely(type != LAST_NORM)) {
+		path_put(parent_path);
+		putname(filename);
+		return -ENOENT;
+	}
 
-	inode_unlock(d_inode(parent));
-	dput(parent);
-	return ret;
+	err = mnt_want_write(parent_path->mnt);
+	if (err) {
+		path_put(parent_path);
+		putname(filename);
+		return -ENOENT;
+	}
+
+	inode_lock_nested(parent_path->dentry->d_inode, I_MUTEX_PARENT);
+	d = lookup_one_qstr_excl(&last, parent_path->dentry, 0);
+	if (IS_ERR(d))
+		goto err_out;
+
+	if (d_is_negative(d)) {
+		dput(d);
+		goto err_out;
+	}
+
+	path->dentry = d;
+	path->mnt = mntget(parent_path->mnt);
+
+	if (test_share_config_flag(share_conf, KSMBD_SHARE_FLAG_CROSSMNT)) {
+		err = follow_down(path);
+		if (err < 0) {
+			path_put(path);
+			goto err_out;
+		}
+	}
+
+	putname(filename);
+	return 0;
+
+err_out:
+	inode_unlock(d_inode(parent_path->dentry));
+	mnt_drop_write(parent_path->mnt);
+	path_put(parent_path);
+	putname(filename);
+	return -ENOENT;
 }
 
-int ksmbd_vfs_query_maximal_access(struct user_namespace *user_ns,
+void ksmbd_vfs_query_maximal_access(struct user_namespace *user_ns,
 				   struct dentry *dentry, __le32 *daccess)
 {
-	struct dentry *parent;
-	int ret = 0;
-
 	*daccess = cpu_to_le32(FILE_READ_ATTRIBUTES | READ_CONTROL);
 
 	if (!inode_permission(user_ns, d_inode(dentry), MAY_OPEN | MAY_WRITE))
@@ -138,19 +153,8 @@
 	if (!inode_permission(user_ns, d_inode(dentry), MAY_OPEN | MAY_EXEC))
 		*daccess |= FILE_EXECUTE_LE;
 
-	parent = dget_parent(dentry);
-	ret = ksmbd_vfs_lock_parent(user_ns, parent, dentry);
-	if (ret) {
-		dput(parent);
-		return ret;
-	}
-
-	if (!inode_permission(user_ns, d_inode(parent), MAY_EXEC | MAY_WRITE))
+	if (!inode_permission(user_ns, d_inode(dentry->d_parent), MAY_EXEC | MAY_WRITE))
 		*daccess |= FILE_DELETE_LE;
-
-	inode_unlock(d_inode(parent));
-	dput(parent);
-	return ret;
 }
 
 /**
@@ -186,6 +190,7 @@
 	} else {
 		pr_err("File(%s): creation failed (err:%d)\n", name, err);
 	}
+
 	done_path_create(&path, dentry);
 	return err;
 }
@@ -219,27 +224,26 @@
 	user_ns = mnt_user_ns(path.mnt);
 	mode |= S_IFDIR;
 	err = vfs_mkdir(user_ns, d_inode(path.dentry), dentry, mode);
-	if (err) {
-		goto out;
-	} else if (d_unhashed(dentry)) {
+	if (!err && d_unhashed(dentry)) {
 		struct dentry *d;
 
 		d = lookup_one(user_ns, dentry->d_name.name, dentry->d_parent,
 			       dentry->d_name.len);
 		if (IS_ERR(d)) {
 			err = PTR_ERR(d);
-			goto out;
+			goto out_err;
 		}
 		if (unlikely(d_is_negative(d))) {
 			dput(d);
 			err = -ENOENT;
-			goto out;
+			goto out_err;
 		}
 
 		ksmbd_vfs_inherit_owner(work, d_inode(path.dentry), d_inode(d));
 		dput(d);
 	}
-out:
+
+out_err:
 	done_path_create(&path, dentry);
 	if (err)
 		pr_err("mkdir(%s): creation failed (err:%d)\n", name, err);
@@ -359,15 +363,15 @@
  * @fid:	file id of open file
  * @count:	read byte count
  * @pos:	file pos
+ * @rbuf:	read data buffer
  *
  * Return:	number of read bytes on success, otherwise error
  */
 int ksmbd_vfs_read(struct ksmbd_work *work, struct ksmbd_file *fp, size_t count,
-		   loff_t *pos)
+		   loff_t *pos, char *rbuf)
 {
 	struct file *filp = fp->filp;
 	ssize_t nbytes = 0;
-	char *rbuf = work->aux_payload_buf;
 	struct inode *inode = file_inode(filp);
 
 	if (S_ISDIR(inode->i_mode))
@@ -378,8 +382,7 @@
 
 	if (work->conn->connection_type) {
 		if (!(fp->daccess & (FILE_READ_DATA_LE | FILE_EXECUTE_LE))) {
-			pr_err("no right to read(%pd)\n",
-			       fp->filp->f_path.dentry);
+			pr_err("no right to read(%pD)\n", fp->filp);
 			return -EACCES;
 		}
 	}
@@ -399,8 +402,7 @@
 
 	nbytes = kernel_read(filp, rbuf, count, pos);
 	if (nbytes < 0) {
-		pr_err("smb read failed for (%s), err = %zd\n",
-		       fp->filename, nbytes);
+		pr_err("smb read failed, err = %zd\n", nbytes);
 		return nbytes;
 	}
 
@@ -413,7 +415,8 @@
 {
 	char *stream_buf = NULL, *wbuf;
 	struct user_namespace *user_ns = file_mnt_user_ns(fp->filp);
-	size_t size, v_len;
+	size_t size;
+	ssize_t v_len;
 	int err = 0;
 
 	ksmbd_debug(VFS, "write stream data pos : %llu, count : %zd\n",
@@ -430,14 +433,14 @@
 				       fp->stream.name,
 				       fp->stream.size,
 				       &stream_buf);
-	if ((int)v_len < 0) {
+	if (v_len < 0) {
 		pr_err("not found stream in xattr : %zd\n", v_len);
-		err = (int)v_len;
+		err = v_len;
 		goto out;
 	}
 
 	if (v_len < size) {
-		wbuf = kvmalloc(size, GFP_KERNEL | __GFP_ZERO);
+		wbuf = kvzalloc(size, GFP_KERNEL);
 		if (!wbuf) {
 			err = -ENOMEM;
 			goto out;
@@ -452,11 +455,12 @@
 	memcpy(&stream_buf[*pos], buf, count);
 
 	err = ksmbd_vfs_setxattr(user_ns,
-				 fp->filp->f_path.dentry,
+				 &fp->filp->f_path,
 				 fp->stream.name,
 				 (void *)stream_buf,
 				 size,
-				 0);
+				 0,
+				 true);
 	if (err < 0)
 		goto out;
 
@@ -483,15 +487,13 @@
 		    char *buf, size_t count, loff_t *pos, bool sync,
 		    ssize_t *written)
 {
-	struct ksmbd_session *sess = work->sess;
 	struct file *filp;
 	loff_t	offset = *pos;
 	int err = 0;
 
-	if (sess->conn->connection_type) {
+	if (work->conn->connection_type) {
 		if (!(fp->daccess & FILE_WRITE_DATA_LE)) {
-			pr_err("no right to write(%pd)\n",
-			       fp->filp->f_path.dentry);
+			pr_err("no right to write(%pD)\n", fp->filp);
 			err = -EACCES;
 			goto out;
 		}
@@ -515,6 +517,9 @@
 		}
 	}
 
+	/* Reserve lease break for parent dir at closing time */
+	fp->reserve_lease_break = true;
+
 	/* Do we need to break any of a levelII oplock? */
 	smb_break_all_levII_oplock(work, fp, 1);
 
@@ -530,8 +535,8 @@
 	if (sync) {
 		err = vfs_fsync_range(filp, offset, offset + *written, 0);
 		if (err < 0)
-			pr_err("fsync failed for filename = %pd, err = %d\n",
-			       fp->filp->f_path.dentry, err);
+			pr_err("fsync failed for filename = %pD, err = %d\n",
+			       fp->filp, err);
 	}
 
 out:
@@ -546,7 +551,7 @@
  *
  * Return:	0 on success, otherwise error
  */
-int ksmbd_vfs_getattr(struct path *path, struct kstat *stat)
+int ksmbd_vfs_getattr(const struct path *path, struct kstat *stat)
 {
 	int err;
 
@@ -586,54 +591,32 @@
  *
  * Return:	0 on success, otherwise error
  */
-int ksmbd_vfs_remove_file(struct ksmbd_work *work, char *name)
+int ksmbd_vfs_remove_file(struct ksmbd_work *work, const struct path *path)
 {
 	struct user_namespace *user_ns;
-	struct path path;
-	struct dentry *parent;
+	struct dentry *parent = path->dentry->d_parent;
 	int err;
 
 	if (ksmbd_override_fsids(work))
 		return -ENOMEM;
 
-	err = ksmbd_vfs_kern_path(work, name, LOOKUP_NO_SYMLINKS, &path, false);
-	if (err) {
-		ksmbd_debug(VFS, "can't get %s, err %d\n", name, err);
-		ksmbd_revert_fsids(work);
-		return err;
-	}
-
-	user_ns = mnt_user_ns(path.mnt);
-	parent = dget_parent(path.dentry);
-	err = ksmbd_vfs_lock_parent(user_ns, parent, path.dentry);
-	if (err) {
-		dput(parent);
-		path_put(&path);
-		ksmbd_revert_fsids(work);
-		return err;
-	}
-
-	if (!d_inode(path.dentry)->i_nlink) {
+	if (!d_inode(path->dentry)->i_nlink) {
 		err = -ENOENT;
 		goto out_err;
 	}
 
-	if (S_ISDIR(d_inode(path.dentry)->i_mode)) {
-		err = vfs_rmdir(user_ns, d_inode(parent), path.dentry);
+	user_ns = mnt_user_ns(path->mnt);
+	if (S_ISDIR(d_inode(path->dentry)->i_mode)) {
+		err = vfs_rmdir(user_ns, d_inode(parent), path->dentry);
 		if (err && err != -ENOTEMPTY)
-			ksmbd_debug(VFS, "%s: rmdir failed, err %d\n", name,
-				    err);
+			ksmbd_debug(VFS, "rmdir failed, err %d\n", err);
 	} else {
-		err = vfs_unlink(user_ns, d_inode(parent), path.dentry, NULL);
+		err = vfs_unlink(user_ns, d_inode(parent), path->dentry, NULL);
 		if (err)
-			ksmbd_debug(VFS, "%s: unlink failed, err %d\n", name,
-				    err);
+			ksmbd_debug(VFS, "unlink failed, err %d\n", err);
 	}
 
 out_err:
-	inode_unlock(d_inode(parent));
-	dput(parent);
-	path_put(&path);
 	ksmbd_revert_fsids(work);
 	return err;
 }
@@ -692,149 +675,125 @@
 	return err;
 }
 
-static int ksmbd_validate_entry_in_use(struct dentry *src_dent)
+int ksmbd_vfs_rename(struct ksmbd_work *work, const struct path *old_path,
+		     char *newname, int flags)
 {
-	struct dentry *dst_dent;
+	struct dentry *old_parent, *new_dentry, *trap;
+	struct dentry *old_child = old_path->dentry;
+	struct path new_path;
+	struct qstr new_last;
+	struct renamedata rd;
+	struct filename *to;
+	struct ksmbd_share_config *share_conf = work->tcon->share_conf;
+	struct ksmbd_file *parent_fp;
+	int new_type;
+	int err, lookup_flags = LOOKUP_NO_SYMLINKS;
 
-	spin_lock(&src_dent->d_lock);
-	list_for_each_entry(dst_dent, &src_dent->d_subdirs, d_child) {
-		struct ksmbd_file *child_fp;
+	if (ksmbd_override_fsids(work))
+		return -ENOMEM;
 
-		if (d_really_is_negative(dst_dent))
-			continue;
+	to = getname_kernel(newname);
+	if (IS_ERR(to)) {
+		err = PTR_ERR(to);
+		goto revert_fsids;
+	}
 
-		child_fp = ksmbd_lookup_fd_inode(d_inode(dst_dent));
-		if (child_fp) {
-			spin_unlock(&src_dent->d_lock);
-			ksmbd_debug(VFS, "Forbid rename, sub file/dir is in use\n");
-			return -EACCES;
-		}
+retry:
+	err = vfs_path_parent_lookup(to, lookup_flags | LOOKUP_BENEATH,
+				     &new_path, &new_last, &new_type,
+				     &share_conf->vfs_path);
+	if (err)
+		goto out1;
+
+	if (old_path->mnt != new_path.mnt) {
+		err = -EXDEV;
+		goto out2;
 	}
-	spin_unlock(&src_dent->d_lock);
 
-	return 0;
-}
+	err = mnt_want_write(old_path->mnt);
+	if (err)
+		goto out2;
 
-static int __ksmbd_vfs_rename(struct ksmbd_work *work,
-			      struct user_namespace *src_user_ns,
-			      struct dentry *src_dent_parent,
-			      struct dentry *src_dent,
-			      struct user_namespace *dst_user_ns,
-			      struct dentry *dst_dent_parent,
-			      struct dentry *trap_dent,
-			      char *dst_name)
-{
-	struct dentry *dst_dent;
-	int err;
+	trap = lock_rename_child(old_child, new_path.dentry);
 
-	if (!work->tcon->posix_extensions) {
-		err = ksmbd_validate_entry_in_use(src_dent);
-		if (err)
-			return err;
+	old_parent = dget(old_child->d_parent);
+	if (d_unhashed(old_child)) {
+		err = -EINVAL;
+		goto out3;
 	}
 
-	if (d_really_is_negative(src_dent_parent))
-		return -ENOENT;
-	if (d_really_is_negative(dst_dent_parent))
-		return -ENOENT;
-	if (d_really_is_negative(src_dent))
-		return -ENOENT;
-	if (src_dent == trap_dent)
-		return -EINVAL;
-
-	if (ksmbd_override_fsids(work))
-		return -ENOMEM;
+	parent_fp = ksmbd_lookup_fd_inode(old_child->d_parent);
+	if (parent_fp) {
+		if (parent_fp->daccess & FILE_DELETE_LE) {
+			pr_err("parent dir is opened with delete access\n");
+			err = -ESHARE;
+			ksmbd_fd_put(work, parent_fp);
+			goto out3;
+		}
+		ksmbd_fd_put(work, parent_fp);
+	}
 
-	dst_dent = lookup_one(dst_user_ns, dst_name, dst_dent_parent,
-			      strlen(dst_name));
-	err = PTR_ERR(dst_dent);
-	if (IS_ERR(dst_dent)) {
-		pr_err("lookup failed %s [%d]\n", dst_name, err);
-		goto out;
+	new_dentry = lookup_one_qstr_excl(&new_last, new_path.dentry,
+					  lookup_flags | LOOKUP_RENAME_TARGET);
+	if (IS_ERR(new_dentry)) {
+		err = PTR_ERR(new_dentry);
+		goto out3;
 	}
 
-	err = -ENOTEMPTY;
-	if (dst_dent != trap_dent && !d_really_is_positive(dst_dent)) {
-		struct renamedata rd = {
-			.old_mnt_userns	= src_user_ns,
-			.old_dir	= d_inode(src_dent_parent),
-			.old_dentry	= src_dent,
-			.new_mnt_userns	= dst_user_ns,
-			.new_dir	= d_inode(dst_dent_parent),
-			.new_dentry	= dst_dent,
-		};
-		err = vfs_rename(&rd);
+	if (d_is_symlink(new_dentry)) {
+		err = -EACCES;
+		goto out4;
 	}
-	if (err)
-		pr_err("vfs_rename failed err %d\n", err);
-	if (dst_dent)
-		dput(dst_dent);
-out:
-	ksmbd_revert_fsids(work);
-	return err;
-}
 
-int ksmbd_vfs_fp_rename(struct ksmbd_work *work, struct ksmbd_file *fp,
-			char *newname)
-{
-	struct user_namespace *user_ns;
-	struct path dst_path;
-	struct dentry *src_dent_parent, *dst_dent_parent;
-	struct dentry *src_dent, *trap_dent, *src_child;
-	char *dst_name;
-	int err;
+	/*
+	 * explicitly handle file overwrite case, for compatibility with
+	 * filesystems that may not support rename flags (e.g: fuse)
+	 */
+	if ((flags & RENAME_NOREPLACE) && d_is_positive(new_dentry)) {
+		err = -EEXIST;
+		goto out4;
+	}
+	flags &= ~(RENAME_NOREPLACE);
 
-	dst_name = extract_last_component(newname);
-	if (!dst_name) {
-		dst_name = newname;
-		newname = "";
+	if (old_child == trap) {
+		err = -EINVAL;
+		goto out4;
 	}
 
-	src_dent_parent = dget_parent(fp->filp->f_path.dentry);
-	src_dent = fp->filp->f_path.dentry;
-
-	err = ksmbd_vfs_kern_path(work, newname,
-				  LOOKUP_NO_SYMLINKS | LOOKUP_DIRECTORY,
-				  &dst_path, false);
-	if (err) {
-		ksmbd_debug(VFS, "Cannot get path for %s [%d]\n", newname, err);
-		goto out;
+	if (new_dentry == trap) {
+		err = -ENOTEMPTY;
+		goto out4;
 	}
-	dst_dent_parent = dst_path.dentry;
 
-	trap_dent = lock_rename(src_dent_parent, dst_dent_parent);
-	dget(src_dent);
-	dget(dst_dent_parent);
-	user_ns = file_mnt_user_ns(fp->filp);
-	src_child = lookup_one(user_ns, src_dent->d_name.name, src_dent_parent,
-			       src_dent->d_name.len);
-	if (IS_ERR(src_child)) {
-		err = PTR_ERR(src_child);
-		goto out_lock;
-	}
-
-	if (src_child != src_dent) {
-		err = -ESTALE;
-		dput(src_child);
-		goto out_lock;
-	}
-	dput(src_child);
-
-	err = __ksmbd_vfs_rename(work,
-				 user_ns,
-				 src_dent_parent,
-				 src_dent,
-				 mnt_user_ns(dst_path.mnt),
-				 dst_dent_parent,
-				 trap_dent,
-				 dst_name);
-out_lock:
-	dput(src_dent);
-	dput(dst_dent_parent);
-	unlock_rename(src_dent_parent, dst_dent_parent);
-	path_put(&dst_path);
-out:
-	dput(src_dent_parent);
+	rd.old_mnt_userns	= mnt_user_ns(old_path->mnt),
+	rd.old_dir		= d_inode(old_parent),
+	rd.old_dentry		= old_child,
+	rd.new_mnt_userns	= mnt_user_ns(new_path.mnt),
+	rd.new_dir		= new_path.dentry->d_inode,
+	rd.new_dentry		= new_dentry,
+	rd.flags		= flags,
+	rd.delegated_inode	= NULL,
+	err = vfs_rename(&rd);
+	if (err)
+		ksmbd_debug(VFS, "vfs_rename failed err %d\n", err);
+
+out4:
+	dput(new_dentry);
+out3:
+	dput(old_parent);
+	unlock_rename(old_parent, new_path.dentry);
+	mnt_drop_write(old_path->mnt);
+out2:
+	path_put(&new_path);
+
+	if (retry_estale(err, lookup_flags)) {
+		lookup_flags |= LOOKUP_REVAL;
+		goto retry;
+	}
+out1:
+	putname(to);
+revert_fsids:
+	ksmbd_revert_fsids(work);
 	return err;
 }
 
@@ -876,8 +835,7 @@
 
 	err = vfs_truncate(&filp->f_path, size);
 	if (err)
-		pr_err("truncate failed for filename : %s err %d\n",
-		       fp->filename, err);
+		pr_err("truncate failed, err %d\n", err);
 	return err;
 }
 
@@ -898,7 +856,7 @@
 	if (size <= 0)
 		return size;
 
-	vlist = kvmalloc(size, GFP_KERNEL | __GFP_ZERO);
+	vlist = kvzalloc(size, GFP_KERNEL);
 	if (!vlist)
 		return -ENOMEM;
 
@@ -956,28 +914,38 @@
 /**
  * ksmbd_vfs_setxattr() - vfs helper for smb set extended attributes value
  * @user_ns:	user namespace
- * @dentry:	dentry to set XATTR at
- * @name:	xattr name for setxattr
- * @value:	xattr value to set
- * @size:	size of xattr value
+ * @path:	path of dentry to set XATTR at
+ * @attr_name:	xattr name for setxattr
+ * @attr_value:	xattr value to set
+ * @attr_size:	size of xattr value
  * @flags:	destination buffer length
+ * @get_write:	get write access to a mount
  *
  * Return:	0 on success, otherwise error
  */
 int ksmbd_vfs_setxattr(struct user_namespace *user_ns,
-		       struct dentry *dentry, const char *attr_name,
-		       const void *attr_value, size_t attr_size, int flags)
+		       const struct path *path, const char *attr_name,
+		       const void *attr_value, size_t attr_size, int flags,
+		       bool get_write)
 {
 	int err;
 
+	if (get_write == true) {
+		err = mnt_want_write(path->mnt);
+		if (err)
+			return err;
+	}
+
 	err = vfs_setxattr(user_ns,
-			   dentry,
+			   path->dentry,
 			   attr_name,
 			   attr_value,
 			   attr_size,
 			   flags);
 	if (err)
 		ksmbd_debug(VFS, "setxattr failed, err %d\n", err);
+	if (get_write == true)
+		mnt_drop_write(path->mnt);
 	return err;
 }
 
@@ -1018,7 +986,9 @@
 				     FALLOC_FL_PUNCH_HOLE | FALLOC_FL_KEEP_SIZE,
 				     off, len);
 
-	return vfs_fallocate(fp->filp, FALLOC_FL_ZERO_RANGE, off, len);
+	return vfs_fallocate(fp->filp,
+			     FALLOC_FL_ZERO_RANGE | FALLOC_FL_KEEP_SIZE,
+			     off, len);
 }
 
 int ksmbd_vfs_fqar_lseek(struct ksmbd_file *fp, loff_t start, loff_t length,
@@ -1049,7 +1019,7 @@
 	*out_count = 0;
 	end = start + length;
 	while (start < end && *out_count < in_count) {
-		extent_start = f->f_op->llseek(f, start, SEEK_DATA);
+		extent_start = vfs_llseek(f, start, SEEK_DATA);
 		if (extent_start < 0) {
 			if (extent_start != -ENXIO)
 				ret = (int)extent_start;
@@ -1059,7 +1029,7 @@
 		if (extent_start >= end)
 			break;
 
-		extent_end = f->f_op->llseek(f, extent_start, SEEK_HOLE);
+		extent_end = vfs_llseek(f, extent_start, SEEK_HOLE);
 		if (extent_end < 0) {
 			if (extent_end != -ENXIO)
 				ret = (int)extent_end;
@@ -1079,19 +1049,34 @@
 }
 
 int ksmbd_vfs_remove_xattr(struct user_namespace *user_ns,
-			   struct dentry *dentry, char *attr_name)
+			   const struct path *path, char *attr_name)
 {
-	return vfs_removexattr(user_ns, dentry, attr_name);
+	int err;
+
+	err = mnt_want_write(path->mnt);
+	if (err)
+		return err;
+
+	err = vfs_removexattr(user_ns, path->dentry, attr_name);
+	mnt_drop_write(path->mnt);
+
+	return err;
 }
 
-int ksmbd_vfs_unlink(struct user_namespace *user_ns,
-		     struct dentry *dir, struct dentry *dentry)
+int ksmbd_vfs_unlink(struct file *filp)
 {
 	int err = 0;
+	struct dentry *dir, *dentry = filp->f_path.dentry;
+	struct user_namespace *user_ns = file_mnt_user_ns(filp);
 
-	err = ksmbd_vfs_lock_parent(user_ns, dir, dentry);
+	err = mnt_want_write(filp->f_path.mnt);
 	if (err)
 		return err;
+
+	dir = dget_parent(dentry);
+	err = ksmbd_vfs_lock_parent(dir, dentry);
+	if (err)
+		goto out;
 	dget(dentry);
 
 	if (S_ISDIR(d_inode(dentry)->i_mode))
@@ -1103,6 +1088,9 @@
 	inode_unlock(d_inode(dir));
 	if (err)
 		ksmbd_debug(VFS, "failed to delete, err %d\n", err);
+out:
+	dput(dir);
+	mnt_drop_write(filp->f_path.mnt);
 
 	return err;
 }
@@ -1149,12 +1137,23 @@
 			     unsigned int d_type)
 {
 	struct ksmbd_readdir_data *buf;
+	int cmp = -EINVAL;
 
 	buf = container_of(ctx, struct ksmbd_readdir_data, ctx);
 
 	if (buf->used != namlen)
 		return 0;
-	if (!strncasecmp((char *)buf->private, name, namlen)) {
+	if (IS_ENABLED(CONFIG_UNICODE) && buf->um) {
+		const struct qstr q_buf = {.name = buf->private,
+					   .len = buf->used};
+		const struct qstr q_name = {.name = name,
+					    .len = namlen};
+
+		cmp = utf8_strncasecmp(buf->um, &q_buf, &q_name);
+	}
+	if (cmp < 0)
+		cmp = strncasecmp((char *)buf->private, name, namlen);
+	if (!cmp) {
 		memcpy((char *)buf->private, name, namlen);
 		buf->dirent_count = 1;
 		return -EEXIST;
@@ -1170,7 +1169,8 @@
  *
  * Return:	0 on success, otherwise error
  */
-static int ksmbd_vfs_lookup_in_dir(struct path *dir, char *name, size_t namelen)
+static int ksmbd_vfs_lookup_in_dir(const struct path *dir, char *name,
+				   size_t namelen, struct unicode_map *um)
 {
 	int ret;
 	struct file *dfilp;
@@ -1180,6 +1180,7 @@
 		.private	= name,
 		.used		= namelen,
 		.dirent_count	= 0,
+		.um		= um,
 	};
 
 	dfilp = dentry_open(dir, flags, current_cred());
@@ -1194,32 +1195,29 @@
 }
 
 /**
- * ksmbd_vfs_kern_path() - lookup a file and get path info
- * @name:	file path that is relative to share
- * @flags:	lookup flags
- * @path:	if lookup succeed, return path info
+ * ksmbd_vfs_kern_path_locked() - lookup a file and get path info
+ * @name:		file path that is relative to share
+ * @flags:		lookup flags
+ * @parent_path:	if lookup succeed, return parent_path info
+ * @path:		if lookup succeed, return path info
  * @caseless:	caseless filename lookup
  *
  * Return:	0 on success, otherwise error
  */
-int ksmbd_vfs_kern_path(struct ksmbd_work *work, char *name,
-			unsigned int flags, struct path *path, bool caseless)
+int ksmbd_vfs_kern_path_locked(struct ksmbd_work *work, char *name,
+			       unsigned int flags, struct path *parent_path,
+			       struct path *path, bool caseless)
 {
 	struct ksmbd_share_config *share_conf = work->tcon->share_conf;
 	int err;
 
-	flags |= LOOKUP_BENEATH;
-	err = vfs_path_lookup(share_conf->vfs_path.dentry,
-			      share_conf->vfs_path.mnt,
-			      name,
-			      flags,
-			      path);
+	err = ksmbd_vfs_path_lookup_locked(share_conf, name, flags, parent_path,
+					   path);
 	if (!err)
 		return 0;
 
 	if (caseless) {
 		char *filepath;
-		struct path parent;
 		size_t path_len, remain_len;
 
 		filepath = kstrdup(name, GFP_KERNEL);
@@ -1229,10 +1227,10 @@
 		path_len = strlen(filepath);
 		remain_len = path_len;
 
-		parent = share_conf->vfs_path;
-		path_get(&parent);
+		*parent_path = share_conf->vfs_path;
+		path_get(parent_path);
 
-		while (d_can_lookup(parent.dentry)) {
+		while (d_can_lookup(parent_path->dentry)) {
 			char *filename = filepath + path_len - remain_len;
 			char *next = strchrnul(filename, '/');
 			size_t filename_len = next - filename;
@@ -1241,11 +1239,11 @@
 			if (filename_len == 0)
 				break;
 
-			err = ksmbd_vfs_lookup_in_dir(&parent, filename,
-						      filename_len);
-			path_put(&parent);
+			err = ksmbd_vfs_lookup_in_dir(parent_path, filename,
+						      filename_len,
+						      work->conn->um);
 			if (err)
-				goto out;
+				goto out2;
 
 			next[0] = '\0';
 
@@ -1253,26 +1251,50 @@
 					      share_conf->vfs_path.mnt,
 					      filepath,
 					      flags,
-					      &parent);
+					      path);
 			if (err)
-				goto out;
-			else if (is_last) {
-				*path = parent;
-				goto out;
-			}
+				goto out2;
+			else if (is_last)
+				goto out1;
+			path_put(parent_path);
+			*parent_path = *path;
 
 			next[0] = '/';
 			remain_len -= filename_len + 1;
 		}
 
-		path_put(&parent);
 		err = -EINVAL;
-out:
+out2:
+		path_put(parent_path);
+out1:
 		kfree(filepath);
 	}
+
+	if (!err) {
+		err = mnt_want_write(parent_path->mnt);
+		if (err) {
+			path_put(path);
+			path_put(parent_path);
+			return err;
+		}
+
+		err = ksmbd_vfs_lock_parent(parent_path->dentry, path->dentry);
+		if (err) {
+			path_put(path);
+			path_put(parent_path);
+		}
+	}
 	return err;
 }
 
+void ksmbd_vfs_kern_path_unlock(struct path *parent_path, struct path *path)
+{
+	inode_unlock(d_inode(parent_path->dentry));
+	mnt_drop_write(parent_path->mnt);
+	path_put(path);
+	path_put(parent_path);
+}
+
 struct dentry *ksmbd_vfs_kern_path_create(struct ksmbd_work *work,
 					  const char *name,
 					  unsigned int flags,
@@ -1291,13 +1313,13 @@
 }
 
 int ksmbd_vfs_remove_acl_xattrs(struct user_namespace *user_ns,
-				struct dentry *dentry)
+				const struct path *path)
 {
 	char *name, *xattr_list = NULL;
 	ssize_t xattr_list_len;
 	int err = 0;
 
-	xattr_list_len = ksmbd_vfs_listxattr(dentry, &xattr_list);
+	xattr_list_len = ksmbd_vfs_listxattr(path->dentry, &xattr_list);
 	if (xattr_list_len < 0) {
 		goto out;
 	} else if (!xattr_list_len) {
@@ -1313,25 +1335,25 @@
 			     sizeof(XATTR_NAME_POSIX_ACL_ACCESS) - 1) ||
 		    !strncmp(name, XATTR_NAME_POSIX_ACL_DEFAULT,
 			     sizeof(XATTR_NAME_POSIX_ACL_DEFAULT) - 1)) {
-			err = ksmbd_vfs_remove_xattr(user_ns, dentry, name);
+			err = ksmbd_vfs_remove_xattr(user_ns, path, name);
 			if (err)
 				ksmbd_debug(SMB,
 					    "remove acl xattr failed : %s\n", name);
 		}
 	}
+
 out:
 	kvfree(xattr_list);
 	return err;
 }
 
-int ksmbd_vfs_remove_sd_xattrs(struct user_namespace *user_ns,
-			       struct dentry *dentry)
+int ksmbd_vfs_remove_sd_xattrs(struct user_namespace *user_ns, const struct path *path)
 {
 	char *name, *xattr_list = NULL;
 	ssize_t xattr_list_len;
 	int err = 0;
 
-	xattr_list_len = ksmbd_vfs_listxattr(dentry, &xattr_list);
+	xattr_list_len = ksmbd_vfs_listxattr(path->dentry, &xattr_list);
 	if (xattr_list_len < 0) {
 		goto out;
 	} else if (!xattr_list_len) {
@@ -1344,7 +1366,7 @@
 		ksmbd_debug(SMB, "%s, len %zd\n", name, strlen(name));
 
 		if (!strncmp(name, XATTR_NAME_SD, XATTR_NAME_SD_LEN)) {
-			err = ksmbd_vfs_remove_xattr(user_ns, dentry, name);
+			err = ksmbd_vfs_remove_xattr(user_ns, path, name);
 			if (err)
 				ksmbd_debug(SMB, "remove xattr failed : %s\n", name);
 		}
@@ -1368,7 +1390,7 @@
 		return NULL;
 
 	posix_acls = get_acl(inode, acl_type);
-	if (!posix_acls)
+	if (IS_ERR_OR_NULL(posix_acls))
 		return NULL;
 
 	smb_acl = kzalloc(sizeof(struct xattr_smb_acl) +
@@ -1421,13 +1443,15 @@
 
 int ksmbd_vfs_set_sd_xattr(struct ksmbd_conn *conn,
 			   struct user_namespace *user_ns,
-			   struct dentry *dentry,
-			   struct smb_ntsd *pntsd, int len)
+			   const struct path *path,
+			   struct smb_ntsd *pntsd, int len,
+			   bool get_write)
 {
 	int rc;
 	struct ndr sd_ndr = {0}, acl_ndr = {0};
 	struct xattr_ntacl acl = {0};
 	struct xattr_smb_acl *smb_acl, *def_smb_acl = NULL;
+	struct dentry *dentry = path->dentry;
 	struct inode *inode = d_inode(dentry);
 
 	acl.version = 4;
@@ -1479,9 +1503,9 @@
 		goto out;
 	}
 
-	rc = ksmbd_vfs_setxattr(user_ns, dentry,
+	rc = ksmbd_vfs_setxattr(user_ns, path,
 				XATTR_NAME_SD, sd_ndr.data,
-				sd_ndr.offset, 0);
+				sd_ndr.offset, 0, get_write);
 	if (rc < 0)
 		pr_err("Failed to store XATTR ntacl :%d\n", rc);
 
@@ -1541,6 +1565,11 @@
 	}
 
 	*pntsd = acl.sd_buf;
+	if (acl.sd_size < sizeof(struct smb_ntsd)) {
+		pr_err("sd size is invalid\n");
+		goto out_free;
+	}
+
 	(*pntsd)->osidoffset = cpu_to_le32(le32_to_cpu((*pntsd)->osidoffset) -
 					   NDR_NTSD_OFFSETOF);
 	(*pntsd)->gsidoffset = cpu_to_le32(le32_to_cpu((*pntsd)->gsidoffset) -
@@ -1564,8 +1593,9 @@
 }
 
 int ksmbd_vfs_set_dos_attrib_xattr(struct user_namespace *user_ns,
-				   struct dentry *dentry,
-				   struct xattr_dos_attrib *da)
+				   const struct path *path,
+				   struct xattr_dos_attrib *da,
+				   bool get_write)
 {
 	struct ndr n;
 	int err;
@@ -1574,8 +1604,8 @@
 	if (err)
 		return err;
 
-	err = ksmbd_vfs_setxattr(user_ns, dentry, XATTR_NAME_DOS_ATTRIBUTE,
-				 (void *)n.data, n.offset, 0);
+	err = ksmbd_vfs_setxattr(user_ns, path, XATTR_NAME_DOS_ATTRIBUTE,
+				 (void *)n.data, n.offset, 0, get_write);
 	if (err)
 		ksmbd_debug(SMB, "failed to store dos attribute in xattr\n");
 	kfree(n.data);
@@ -1740,11 +1770,11 @@
 	*total_size_written = 0;
 
 	if (!(src_fp->daccess & (FILE_READ_DATA_LE | FILE_EXECUTE_LE))) {
-		pr_err("no right to read(%pd)\n", src_fp->filp->f_path.dentry);
+		pr_err("no right to read(%pD)\n", src_fp->filp);
 		return -EACCES;
 	}
 	if (!(dst_fp->daccess & (FILE_WRITE_DATA_LE | FILE_APPEND_DATA_LE))) {
-		pr_err("no right to write(%pd)\n", dst_fp->filp->f_path.dentry);
+		pr_err("no right to write(%pD)\n", dst_fp->filp);
 		return -EACCES;
 	}
 
@@ -1780,6 +1810,10 @@
 
 		ret = vfs_copy_file_range(src_fp->filp, src_off,
 					  dst_fp->filp, dst_off, len, 0);
+		if (ret == -EOPNOTSUPP || ret == -EXDEV)
+			ret = vfs_copy_file_range(src_fp->filp, src_off,
+						  dst_fp->filp, dst_off, len,
+						  COPY_FILE_SPLICE);
 		if (ret < 0)
 			return ret;
 
@@ -1807,10 +1841,11 @@
 }
 
 int ksmbd_vfs_set_init_posix_acl(struct user_namespace *user_ns,
-				 struct inode *inode)
+				 struct path *path)
 {
 	struct posix_acl_state acl_state;
 	struct posix_acl *acls;
+	struct inode *inode = d_inode(path->dentry);
 	int rc;
 
 	if (!IS_ENABLED(CONFIG_FS_POSIX_ACL))
@@ -1839,6 +1874,7 @@
 		return -ENOMEM;
 	}
 	posix_state_to_acl(&acl_state, acls->a_entries);
+
 	rc = set_posix_acl(user_ns, inode, ACL_TYPE_ACCESS, acls);
 	if (rc < 0)
 		ksmbd_debug(SMB, "Set posix acl(ACL_TYPE_ACCESS) failed, rc : %d\n",
@@ -1851,23 +1887,25 @@
 			ksmbd_debug(SMB, "Set posix acl(ACL_TYPE_DEFAULT) failed, rc : %d\n",
 				    rc);
 	}
+
 	free_acl_state(&acl_state);
 	posix_acl_release(acls);
 	return rc;
 }
 
 int ksmbd_vfs_inherit_posix_acl(struct user_namespace *user_ns,
-				struct inode *inode, struct inode *parent_inode)
+				struct path *path, struct inode *parent_inode)
 {
 	struct posix_acl *acls;
 	struct posix_acl_entry *pace;
+	struct inode *inode = d_inode(path->dentry);
 	int rc, i;
 
 	if (!IS_ENABLED(CONFIG_FS_POSIX_ACL))
 		return -EOPNOTSUPP;
 
 	acls = get_acl(parent_inode, ACL_TYPE_DEFAULT);
-	if (!acls)
+	if (IS_ERR_OR_NULL(acls))
 		return -ENOENT;
 	pace = acls->a_entries;
 
@@ -1889,6 +1927,7 @@
 			ksmbd_debug(SMB, "Set posix acl(ACL_TYPE_DEFAULT) failed, rc : %d\n",
 				    rc);
 	}
+
 	posix_acl_release(acls);
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/vfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/vfs.h
@@ -12,6 +12,7 @@
 #include <linux/namei.h>
 #include <uapi/linux/xattr.h>
 #include <linux/posix_acl.h>
+#include <linux/unicode.h>
 
 #include "smbacl.h"
 #include "xattr.h"
@@ -86,6 +87,7 @@
 	int		last_entry_offset;
 	bool		hide_dot_file;
 	int		flags;
+	int		last_entry_off_align;
 };
 
 struct ksmbd_readdir_data {
@@ -98,6 +100,7 @@
 	unsigned int		used;
 	unsigned int		dirent_count;
 	unsigned int		file_attr;
+	struct unicode_map	*um;
 };
 
 /* ksmbd kstat wrapper to get valid create time when reading dir entry */
@@ -107,25 +110,23 @@
 	__le32			file_attributes;
 };
 
-int ksmbd_vfs_lock_parent(struct user_namespace *user_ns, struct dentry *parent,
-			  struct dentry *child);
-int ksmbd_vfs_may_delete(struct user_namespace *user_ns, struct dentry *dentry);
-int ksmbd_vfs_query_maximal_access(struct user_namespace *user_ns,
+int ksmbd_vfs_lock_parent(struct dentry *parent, struct dentry *child);
+void ksmbd_vfs_query_maximal_access(struct user_namespace *user_ns,
 				   struct dentry *dentry, __le32 *daccess);
 int ksmbd_vfs_create(struct ksmbd_work *work, const char *name, umode_t mode);
 int ksmbd_vfs_mkdir(struct ksmbd_work *work, const char *name, umode_t mode);
-int ksmbd_vfs_read(struct ksmbd_work *work, struct ksmbd_file *fp,
-		   size_t count, loff_t *pos);
+int ksmbd_vfs_read(struct ksmbd_work *work, struct ksmbd_file *fp, size_t count,
+		   loff_t *pos, char *rbuf);
 int ksmbd_vfs_write(struct ksmbd_work *work, struct ksmbd_file *fp,
 		    char *buf, size_t count, loff_t *pos, bool sync,
 		    ssize_t *written);
 int ksmbd_vfs_fsync(struct ksmbd_work *work, u64 fid, u64 p_id);
-int ksmbd_vfs_remove_file(struct ksmbd_work *work, char *name);
+int ksmbd_vfs_remove_file(struct ksmbd_work *work, const struct path *path);
 int ksmbd_vfs_link(struct ksmbd_work *work,
 		   const char *oldname, const char *newname);
-int ksmbd_vfs_getattr(struct path *path, struct kstat *stat);
-int ksmbd_vfs_fp_rename(struct ksmbd_work *work, struct ksmbd_file *fp,
-			char *newname);
+int ksmbd_vfs_getattr(const struct path *path, struct kstat *stat);
+int ksmbd_vfs_rename(struct ksmbd_work *work, const struct path *old_path,
+		     char *newname, int flags);
 int ksmbd_vfs_truncate(struct ksmbd_work *work,
 		       struct ksmbd_file *fp, loff_t size);
 struct srv_copychunk;
@@ -146,15 +147,17 @@
 				struct dentry *dentry, char *attr_name,
 				int attr_name_len);
 int ksmbd_vfs_setxattr(struct user_namespace *user_ns,
-		       struct dentry *dentry, const char *attr_name,
-		       const void *attr_value, size_t attr_size, int flags);
+		       const struct path *path, const char *attr_name,
+		       const void *attr_value, size_t attr_size, int flags,
+		       bool get_write);
 int ksmbd_vfs_xattr_stream_name(char *stream_name, char **xattr_stream_name,
 				size_t *xattr_stream_name_size, int s_type);
 int ksmbd_vfs_remove_xattr(struct user_namespace *user_ns,
-			   struct dentry *dentry, char *attr_name);
-int ksmbd_vfs_kern_path(struct ksmbd_work *work,
-			char *name, unsigned int flags, struct path *path,
-			bool caseless);
+			   const struct path *path, char *attr_name);
+int ksmbd_vfs_kern_path_locked(struct ksmbd_work *work, char *name,
+			       unsigned int flags, struct path *parent_path,
+			       struct path *path, bool caseless);
+void ksmbd_vfs_kern_path_unlock(struct path *parent_path, struct path *path);
 struct dentry *ksmbd_vfs_kern_path_create(struct ksmbd_work *work,
 					  const char *name,
 					  unsigned int flags,
@@ -167,8 +170,7 @@
 int ksmbd_vfs_fqar_lseek(struct ksmbd_file *fp, loff_t start, loff_t length,
 			 struct file_allocated_range_buffer *ranges,
 			 unsigned int in_count, unsigned int *out_count);
-int ksmbd_vfs_unlink(struct user_namespace *user_ns,
-		     struct dentry *dir, struct dentry *dentry);
+int ksmbd_vfs_unlink(struct file *filp);
 void *ksmbd_vfs_init_kstat(char **p, struct ksmbd_kstat *ksmbd_kstat);
 int ksmbd_vfs_fill_dentry_attrs(struct ksmbd_work *work,
 				struct user_namespace *user_ns,
@@ -178,26 +180,27 @@
 int ksmbd_vfs_posix_lock_wait_timeout(struct file_lock *flock, long timeout);
 void ksmbd_vfs_posix_lock_unblock(struct file_lock *flock);
 int ksmbd_vfs_remove_acl_xattrs(struct user_namespace *user_ns,
-				struct dentry *dentry);
-int ksmbd_vfs_remove_sd_xattrs(struct user_namespace *user_ns,
-			       struct dentry *dentry);
+				const struct path *path);
+int ksmbd_vfs_remove_sd_xattrs(struct user_namespace *user_ns, const struct path *path);
 int ksmbd_vfs_set_sd_xattr(struct ksmbd_conn *conn,
 			   struct user_namespace *user_ns,
-			   struct dentry *dentry,
-			   struct smb_ntsd *pntsd, int len);
+			   const struct path *path,
+			   struct smb_ntsd *pntsd, int len,
+			   bool get_write);
 int ksmbd_vfs_get_sd_xattr(struct ksmbd_conn *conn,
 			   struct user_namespace *user_ns,
 			   struct dentry *dentry,
 			   struct smb_ntsd **pntsd);
 int ksmbd_vfs_set_dos_attrib_xattr(struct user_namespace *user_ns,
-				   struct dentry *dentry,
-				   struct xattr_dos_attrib *da);
+				   const struct path *path,
+				   struct xattr_dos_attrib *da,
+				   bool get_write);
 int ksmbd_vfs_get_dos_attrib_xattr(struct user_namespace *user_ns,
 				   struct dentry *dentry,
 				   struct xattr_dos_attrib *da);
 int ksmbd_vfs_set_init_posix_acl(struct user_namespace *user_ns,
-				 struct inode *inode);
+				 struct path *path);
 int ksmbd_vfs_inherit_posix_acl(struct user_namespace *user_ns,
-				struct inode *inode,
+				struct path *path,
 				struct inode *parent_inode);
 #endif /* __KSMBD_VFS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/vfs_cache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/vfs_cache.c
@@ -65,14 +65,14 @@
 	return tmp & inode_hash_mask;
 }
 
-static struct ksmbd_inode *__ksmbd_inode_lookup(struct inode *inode)
+static struct ksmbd_inode *__ksmbd_inode_lookup(struct dentry *de)
 {
 	struct hlist_head *head = inode_hashtable +
-		inode_hash(inode->i_sb, inode->i_ino);
+		inode_hash(d_inode(de)->i_sb, (unsigned long)de);
 	struct ksmbd_inode *ci = NULL, *ret_ci = NULL;
 
 	hlist_for_each_entry(ci, head, m_hash) {
-		if (ci->m_inode == inode) {
+		if (ci->m_de == de) {
 			if (atomic_inc_not_zero(&ci->m_count))
 				ret_ci = ci;
 			break;
@@ -83,29 +83,30 @@
 
 static struct ksmbd_inode *ksmbd_inode_lookup(struct ksmbd_file *fp)
 {
-	return __ksmbd_inode_lookup(file_inode(fp->filp));
+	return __ksmbd_inode_lookup(fp->filp->f_path.dentry);
 }
 
-static struct ksmbd_inode *ksmbd_inode_lookup_by_vfsinode(struct inode *inode)
+struct ksmbd_inode *ksmbd_inode_lookup_lock(struct dentry *d)
 {
 	struct ksmbd_inode *ci;
 
 	read_lock(&inode_hash_lock);
-	ci = __ksmbd_inode_lookup(inode);
+	ci = __ksmbd_inode_lookup(d);
 	read_unlock(&inode_hash_lock);
+
 	return ci;
 }
 
-int ksmbd_query_inode_status(struct inode *inode)
+int ksmbd_query_inode_status(struct dentry *dentry)
 {
 	struct ksmbd_inode *ci;
 	int ret = KSMBD_INODE_STATUS_UNKNOWN;
 
 	read_lock(&inode_hash_lock);
-	ci = __ksmbd_inode_lookup(inode);
+	ci = __ksmbd_inode_lookup(dentry);
 	if (ci) {
 		ret = KSMBD_INODE_STATUS_OK;
-		if (ci->m_flags & S_DEL_PENDING)
+		if (ci->m_flags & (S_DEL_PENDING | S_DEL_ON_CLS))
 			ret = KSMBD_INODE_STATUS_PENDING_DELETE;
 		atomic_dec(&ci->m_count);
 	}
@@ -115,7 +116,7 @@
 
 bool ksmbd_inode_pending_delete(struct ksmbd_file *fp)
 {
-	return (fp->f_ci->m_flags & S_DEL_PENDING);
+	return (fp->f_ci->m_flags & (S_DEL_PENDING | S_DEL_ON_CLS));
 }
 
 void ksmbd_set_inode_pending_delete(struct ksmbd_file *fp)
@@ -142,7 +143,7 @@
 static void ksmbd_inode_hash(struct ksmbd_inode *ci)
 {
 	struct hlist_head *b = inode_hashtable +
-		inode_hash(ci->m_inode->i_sb, ci->m_inode->i_ino);
+		inode_hash(d_inode(ci->m_de)->i_sb, (unsigned long)ci->m_de);
 
 	hlist_add_head(&ci->m_hash, b);
 }
@@ -156,7 +157,6 @@
 
 static int ksmbd_inode_init(struct ksmbd_inode *ci, struct ksmbd_file *fp)
 {
-	ci->m_inode = file_inode(fp->filp);
 	atomic_set(&ci->m_count, 1);
 	atomic_set(&ci->op_count, 0);
 	atomic_set(&ci->sop_count, 0);
@@ -165,6 +165,7 @@
 	INIT_LIST_HEAD(&ci->m_fp_list);
 	INIT_LIST_HEAD(&ci->m_op_list);
 	rwlock_init(&ci->m_lock);
+	ci->m_de = fp->filp->f_path.dentry;
 	return 0;
 }
 
@@ -208,7 +209,7 @@
 	kfree(ci);
 }
 
-static void ksmbd_inode_put(struct ksmbd_inode *ci)
+void ksmbd_inode_put(struct ksmbd_inode *ci)
 {
 	if (atomic_dec_and_test(&ci->m_count))
 		ksmbd_inode_free(ci);
@@ -243,7 +244,6 @@
 
 static void __ksmbd_inode_close(struct ksmbd_file *fp)
 {
-	struct dentry *dir, *dentry;
 	struct ksmbd_inode *ci = fp->f_ci;
 	int err;
 	struct file *filp;
@@ -252,7 +252,7 @@
 	if (ksmbd_stream_fd(fp) && (ci->m_flags & S_DEL_ON_CLS_STREAM)) {
 		ci->m_flags &= ~S_DEL_ON_CLS_STREAM;
 		err = ksmbd_vfs_remove_xattr(file_mnt_user_ns(filp),
-					     filp->f_path.dentry,
+					     &filp->f_path,
 					     fp->stream.name);
 		if (err)
 			pr_err("remove xattr failed : %s\n",
@@ -262,11 +262,9 @@
 	if (atomic_dec_and_test(&ci->m_count)) {
 		write_lock(&ci->m_lock);
 		if (ci->m_flags & (S_DEL_ON_CLS | S_DEL_PENDING)) {
-			dentry = filp->f_path.dentry;
-			dir = dentry->d_parent;
 			ci->m_flags &= ~(S_DEL_ON_CLS | S_DEL_PENDING);
 			write_unlock(&ci->m_lock);
-			ksmbd_vfs_unlink(file_mnt_user_ns(filp), dir, dentry);
+			ksmbd_vfs_unlink(filp);
 			write_lock(&ci->m_lock);
 		}
 		write_unlock(&ci->m_lock);
@@ -328,7 +326,6 @@
 		kfree(smb_lock);
 	}
 
-	kfree(fp->filename);
 	if (ksmbd_stream_fd(fp))
 		kfree(fp->stream.name);
 	kmem_cache_free(filp_cache, fp);
@@ -336,6 +333,9 @@
 
 static struct ksmbd_file *ksmbd_fp_get(struct ksmbd_file *fp)
 {
+	if (fp->f_state != FP_INITED)
+		return NULL;
+
 	if (!atomic_inc_not_zero(&fp->refcount))
 		return NULL;
 	return fp;
@@ -365,12 +365,11 @@
 
 static void set_close_state_blocked_works(struct ksmbd_file *fp)
 {
-	struct ksmbd_work *cancel_work, *ctmp;
+	struct ksmbd_work *cancel_work;
 
 	spin_lock(&fp->f_lock);
-	list_for_each_entry_safe(cancel_work, ctmp, &fp->blocked_works,
+	list_for_each_entry(cancel_work, &fp->blocked_works,
 				 fp_entry) {
-		list_del(&cancel_work->fp_entry);
 		cancel_work->state = KSMBD_WORK_CLOSED;
 		cancel_work->cancel_fn(cancel_work->cancel_argv);
 	}
@@ -386,15 +385,20 @@
 		return 0;
 
 	ft = &work->sess->file_table;
-	read_lock(&ft->lock);
+	write_lock(&ft->lock);
 	fp = idr_find(ft->idr, id);
 	if (fp) {
 		set_close_state_blocked_works(fp);
 
-		if (!atomic_dec_and_test(&fp->refcount))
+		if (fp->f_state != FP_INITED)
 			fp = NULL;
+		else {
+			fp->f_state = FP_CLOSED;
+			if (!atomic_dec_and_test(&fp->refcount))
+				fp = NULL;
+		}
 	}
-	read_unlock(&ft->lock);
+	write_unlock(&ft->lock);
 
 	if (!fp)
 		return -EINVAL;
@@ -484,12 +488,15 @@
 	return fp;
 }
 
-struct ksmbd_file *ksmbd_lookup_fd_inode(struct inode *inode)
+struct ksmbd_file *ksmbd_lookup_fd_inode(struct dentry *dentry)
 {
 	struct ksmbd_file	*lfp;
 	struct ksmbd_inode	*ci;
+	struct inode		*inode = d_inode(dentry);
 
-	ci = ksmbd_inode_lookup_by_vfsinode(inode);
+	read_lock(&inode_hash_lock);
+	ci = __ksmbd_inode_lookup(dentry);
+	read_unlock(&inode_hash_lock);
 	if (!ci)
 		return NULL;
 
@@ -497,6 +504,7 @@
 	list_for_each_entry(lfp, &ci->m_fp_list, node) {
 		if (inode == file_inode(lfp->filp)) {
 			atomic_dec(&ci->m_count);
+			lfp = ksmbd_fp_get(lfp);
 			read_unlock(&ci->m_lock);
 			return lfp;
 		}
@@ -569,10 +577,11 @@
 	atomic_set(&fp->refcount, 1);
 
 	fp->filp		= filp;
-	fp->conn		= work->sess->conn;
+	fp->conn		= work->conn;
 	fp->tcon		= work->tcon;
 	fp->volatile_id		= KSMBD_NO_FID;
 	fp->persistent_id	= KSMBD_NO_FID;
+	fp->f_state		= FP_NEW;
 	fp->f_ci		= ksmbd_inode_get(fp);
 
 	if (!fp->f_ci) {
@@ -594,6 +603,17 @@
 	return ERR_PTR(ret);
 }
 
+void ksmbd_update_fstate(struct ksmbd_file_table *ft, struct ksmbd_file *fp,
+			 unsigned int state)
+{
+	if (!fp)
+		return;
+
+	write_lock(&ft->lock);
+	fp->f_state = state;
+	write_unlock(&ft->lock);
+}
+
 static int
 __close_file_table_ids(struct ksmbd_file_table *ft,
 		       struct ksmbd_tree_connect *tcon,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ksmbd/vfs_cache.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ksmbd/vfs_cache.h
@@ -51,7 +51,7 @@
 	atomic_t			op_count;
 	/* opinfo count for streams */
 	atomic_t			sop_count;
-	struct inode			*m_inode;
+	struct dentry			*m_de;
 	unsigned int			m_flags;
 	struct hlist_node		m_hash;
 	struct list_head		m_fp_list;
@@ -60,9 +60,14 @@
 	__le32				m_fattr;
 };
 
+enum {
+	FP_NEW = 0,
+	FP_INITED,
+	FP_CLOSED
+};
+
 struct ksmbd_file {
 	struct file			*filp;
-	char				*filename;
 	u64				persistent_id;
 	u64				volatile_id;
 
@@ -96,19 +101,11 @@
 
 	int				durable_timeout;
 
-	/* for SMB1 */
-	int				pid;
-
-	/* conflict lock fail count for SMB1 */
-	unsigned int			cflock_cnt;
-	/* last lock failure start offset for SMB1 */
-	unsigned long long		llock_fstart;
-
-	int				dirent_offset;
-
 	/* if ls is happening on directory, below is valid*/
 	struct ksmbd_readdir_data	readdir_data;
 	int				dot_dotdot[2];
+	unsigned int			f_state;
+	bool				reserve_lease_break;
 };
 
 static inline void set_ctx_actor(struct dir_context *ctx,
@@ -142,9 +139,11 @@
 struct ksmbd_file *ksmbd_lookup_fd_slow(struct ksmbd_work *work, u64 id,
 					u64 pid);
 void ksmbd_fd_put(struct ksmbd_work *work, struct ksmbd_file *fp);
+struct ksmbd_inode *ksmbd_inode_lookup_lock(struct dentry *d);
+void ksmbd_inode_put(struct ksmbd_inode *ci);
 struct ksmbd_file *ksmbd_lookup_durable_fd(unsigned long long id);
 struct ksmbd_file *ksmbd_lookup_fd_cguid(char *cguid);
-struct ksmbd_file *ksmbd_lookup_fd_inode(struct inode *inode);
+struct ksmbd_file *ksmbd_lookup_fd_inode(struct dentry *dentry);
 unsigned int ksmbd_open_durable_fd(struct ksmbd_file *fp);
 struct ksmbd_file *ksmbd_open_fd(struct ksmbd_work *work, struct file *filp);
 void ksmbd_close_tree_conn_fds(struct ksmbd_work *work);
@@ -153,6 +152,8 @@
 int ksmbd_init_global_file_table(void);
 void ksmbd_free_global_file_table(void);
 void ksmbd_set_fd_limit(unsigned long limit);
+void ksmbd_update_fstate(struct ksmbd_file_table *ft, struct ksmbd_file *fp,
+			 unsigned int state);
 
 /*
  * INODE hash
@@ -166,7 +167,7 @@
 	KSMBD_INODE_STATUS_PENDING_DELETE,
 };
 
-int ksmbd_query_inode_status(struct inode *inode);
+int ksmbd_query_inode_status(struct dentry *dentry);
 bool ksmbd_inode_pending_delete(struct ksmbd_file *fp);
 void ksmbd_set_inode_pending_delete(struct ksmbd_file *fp);
 void ksmbd_clear_inode_pending_delete(struct ksmbd_file *fp);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/libfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/libfs.c
@@ -967,8 +967,8 @@
 EXPORT_SYMBOL_GPL(simple_attr_read);
 
 /* interpret the buffer as a number to call the set function with */
-ssize_t simple_attr_write(struct file *file, const char __user *buf,
-			  size_t len, loff_t *ppos)
+static ssize_t simple_attr_write_xsigned(struct file *file, const char __user *buf,
+			  size_t len, loff_t *ppos, bool is_signed)
 {
 	struct simple_attr *attr;
 	unsigned long long val;
@@ -989,7 +989,10 @@
 		goto out;
 
 	attr->set_buf[size] = '\0';
-	ret = kstrtoull(attr->set_buf, 0, &val);
+	if (is_signed)
+		ret = kstrtoll(attr->set_buf, 0, &val);
+	else
+		ret = kstrtoull(attr->set_buf, 0, &val);
 	if (ret)
 		goto out;
 	ret = attr->set(attr->data, val);
@@ -999,8 +1002,21 @@
 	mutex_unlock(&attr->mutex);
 	return ret;
 }
+
+ssize_t simple_attr_write(struct file *file, const char __user *buf,
+			  size_t len, loff_t *ppos)
+{
+	return simple_attr_write_xsigned(file, buf, len, ppos, false);
+}
 EXPORT_SYMBOL_GPL(simple_attr_write);
 
+ssize_t simple_attr_write_signed(struct file *file, const char __user *buf,
+			  size_t len, loff_t *ppos)
+{
+	return simple_attr_write_xsigned(file, buf, len, ppos, true);
+}
+EXPORT_SYMBOL_GPL(simple_attr_write_signed);
+
 /**
  * generic_fh_to_dentry - generic helper for the fh_to_dentry export operation
  * @sb:		filesystem to do the file handle conversion on
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/clnt4xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/clnt4xdr.c
@@ -261,7 +261,6 @@
 	u32 exclusive;
 	int error;
 	__be32 *p;
-	s32 end;
 
 	memset(lock, 0, sizeof(*lock));
 	locks_init_lock(fl);
@@ -285,13 +284,7 @@
 	fl->fl_type  = exclusive != 0 ? F_WRLCK : F_RDLCK;
 	p = xdr_decode_hyper(p, &l_offset);
 	xdr_decode_hyper(p, &l_len);
-	end = l_offset + l_len - 1;
-
-	fl->fl_start = (loff_t)l_offset;
-	if (l_len == 0 || end < 0)
-		fl->fl_end = OFFSET_MAX;
-	else
-		fl->fl_end = (loff_t)end;
+	nlm4svc_set_file_lock_range(fl, l_offset, l_len);
 	error = 0;
 out:
 	return error;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/host.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/host.c
@@ -164,7 +164,7 @@
 	host->h_addrbuf    = nsm->sm_addrbuf;
 	host->net	   = ni->net;
 	host->h_cred	   = get_cred(ni->cred);
-	strlcpy(host->nodename, utsname()->nodename, sizeof(host->nodename));
+	strscpy(host->nodename, utsname()->nodename, sizeof(host->nodename));
 
 out:
 	return host;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/mon.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/mon.c
@@ -276,6 +276,9 @@
 {
 	struct nsm_handle *new;
 
+	if (!hostname)
+		return NULL;
+
 	new = kzalloc(sizeof(*new) + hostname_len + 1, GFP_KERNEL);
 	if (unlikely(new == NULL))
 		return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/svc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/svc.c
@@ -54,13 +54,9 @@
 
 static DEFINE_MUTEX(nlmsvc_mutex);
 static unsigned int		nlmsvc_users;
-static struct task_struct	*nlmsvc_task;
-static struct svc_rqst		*nlmsvc_rqst;
+static struct svc_serv		*nlmsvc_serv;
 unsigned long			nlmsvc_timeout;
 
-static atomic_t nlm_ntf_refcnt = ATOMIC_INIT(0);
-static DECLARE_WAIT_QUEUE_HEAD(nlm_ntf_wq);
-
 unsigned int lockd_net_id;
 
 /*
@@ -184,6 +180,10 @@
 	nlm_shutdown_hosts();
 	cancel_delayed_work_sync(&ln->grace_period_end);
 	locks_end_grace(&ln->lockd_manager);
+
+	dprintk("lockd_down: service stopped\n");
+
+	svc_exit_thread(rqstp);
 	return 0;
 }
 
@@ -196,8 +196,8 @@
 
 	xprt = svc_find_xprt(serv, name, net, family, 0);
 	if (xprt == NULL)
-		return svc_create_xprt(serv, name, net, family, port,
-						SVC_SOCK_DEFAULTS, cred);
+		return svc_xprt_create(serv, name, net, family, port,
+				       SVC_SOCK_DEFAULTS, cred);
 	svc_xprt_put(xprt);
 	return 0;
 }
@@ -247,7 +247,8 @@
 	if (warned++ == 0)
 		printk(KERN_WARNING
 			"lockd_up: makesock failed, error=%d\n", err);
-	svc_shutdown_net(serv, net);
+	svc_xprt_destroy_all(serv, net);
+	svc_rpcb_cleanup(serv, net);
 	return err;
 }
 
@@ -285,13 +286,12 @@
 			nlm_shutdown_hosts_net(net);
 			cancel_delayed_work_sync(&ln->grace_period_end);
 			locks_end_grace(&ln->lockd_manager);
-			svc_shutdown_net(serv, net);
-			dprintk("%s: per-net data destroyed; net=%x\n",
-				__func__, net->ns.inum);
+			svc_xprt_destroy_all(serv, net);
+			svc_rpcb_cleanup(serv, net);
 		}
 	} else {
-		pr_err("%s: no users! task=%p, net=%x\n",
-			__func__, nlmsvc_task, net->ns.inum);
+		pr_err("%s: no users! net=%x\n",
+			__func__, net->ns.inum);
 		BUG();
 	}
 }
@@ -302,20 +302,16 @@
 	struct in_ifaddr *ifa = (struct in_ifaddr *)ptr;
 	struct sockaddr_in sin;
 
-	if ((event != NETDEV_DOWN) ||
-	    !atomic_inc_not_zero(&nlm_ntf_refcnt))
+	if (event != NETDEV_DOWN)
 		goto out;
 
-	if (nlmsvc_rqst) {
+	if (nlmsvc_serv) {
 		dprintk("lockd_inetaddr_event: removed %pI4\n",
 			&ifa->ifa_local);
 		sin.sin_family = AF_INET;
 		sin.sin_addr.s_addr = ifa->ifa_local;
-		svc_age_temp_xprts_now(nlmsvc_rqst->rq_server,
-			(struct sockaddr *)&sin);
+		svc_age_temp_xprts_now(nlmsvc_serv, (struct sockaddr *)&sin);
 	}
-	atomic_dec(&nlm_ntf_refcnt);
-	wake_up(&nlm_ntf_wq);
 
 out:
 	return NOTIFY_DONE;
@@ -332,21 +328,17 @@
 	struct inet6_ifaddr *ifa = (struct inet6_ifaddr *)ptr;
 	struct sockaddr_in6 sin6;
 
-	if ((event != NETDEV_DOWN) ||
-	    !atomic_inc_not_zero(&nlm_ntf_refcnt))
+	if (event != NETDEV_DOWN)
 		goto out;
 
-	if (nlmsvc_rqst) {
+	if (nlmsvc_serv) {
 		dprintk("lockd_inet6addr_event: removed %pI6\n", &ifa->addr);
 		sin6.sin6_family = AF_INET6;
 		sin6.sin6_addr = ifa->addr;
 		if (ipv6_addr_type(&sin6.sin6_addr) & IPV6_ADDR_LINKLOCAL)
 			sin6.sin6_scope_id = ifa->idev->dev->ifindex;
-		svc_age_temp_xprts_now(nlmsvc_rqst->rq_server,
-			(struct sockaddr *)&sin6);
+		svc_age_temp_xprts_now(nlmsvc_serv, (struct sockaddr *)&sin6);
 	}
-	atomic_dec(&nlm_ntf_refcnt);
-	wake_up(&nlm_ntf_wq);
 
 out:
 	return NOTIFY_DONE;
@@ -357,86 +349,14 @@
 };
 #endif
 
-static void lockd_unregister_notifiers(void)
-{
-	unregister_inetaddr_notifier(&lockd_inetaddr_notifier);
-#if IS_ENABLED(CONFIG_IPV6)
-	unregister_inet6addr_notifier(&lockd_inet6addr_notifier);
-#endif
-	wait_event(nlm_ntf_wq, atomic_read(&nlm_ntf_refcnt) == 0);
-}
-
-static void lockd_svc_exit_thread(void)
-{
-	atomic_dec(&nlm_ntf_refcnt);
-	lockd_unregister_notifiers();
-	svc_exit_thread(nlmsvc_rqst);
-}
-
-static int lockd_start_svc(struct svc_serv *serv)
+static int lockd_get(void)
 {
+	struct svc_serv *serv;
 	int error;
 
-	if (nlmsvc_rqst)
+	if (nlmsvc_serv) {
+		nlmsvc_users++;
 		return 0;
-
-	/*
-	 * Create the kernel thread and wait for it to start.
-	 */
-	nlmsvc_rqst = svc_prepare_thread(serv, &serv->sv_pools[0], NUMA_NO_NODE);
-	if (IS_ERR(nlmsvc_rqst)) {
-		error = PTR_ERR(nlmsvc_rqst);
-		printk(KERN_WARNING
-			"lockd_up: svc_rqst allocation failed, error=%d\n",
-			error);
-		lockd_unregister_notifiers();
-		goto out_rqst;
-	}
-
-	atomic_inc(&nlm_ntf_refcnt);
-	svc_sock_update_bufs(serv);
-	serv->sv_maxconn = nlm_max_connections;
-
-	nlmsvc_task = kthread_create(lockd, nlmsvc_rqst, "%s", serv->sv_name);
-	if (IS_ERR(nlmsvc_task)) {
-		error = PTR_ERR(nlmsvc_task);
-		printk(KERN_WARNING
-			"lockd_up: kthread_run failed, error=%d\n", error);
-		goto out_task;
-	}
-	nlmsvc_rqst->rq_task = nlmsvc_task;
-	wake_up_process(nlmsvc_task);
-
-	dprintk("lockd_up: service started\n");
-	return 0;
-
-out_task:
-	lockd_svc_exit_thread();
-	nlmsvc_task = NULL;
-out_rqst:
-	nlmsvc_rqst = NULL;
-	return error;
-}
-
-static const struct svc_serv_ops lockd_sv_ops = {
-	.svo_shutdown		= svc_rpcb_cleanup,
-	.svo_enqueue_xprt	= svc_xprt_do_enqueue,
-};
-
-static struct svc_serv *lockd_create_svc(void)
-{
-	struct svc_serv *serv;
-
-	/*
-	 * Check whether we're already up and running.
-	 */
-	if (nlmsvc_rqst) {
-		/*
-		 * Note: increase service usage, because later in case of error
-		 * svc_destroy() will be called.
-		 */
-		svc_get(nlmsvc_rqst->rq_server);
-		return nlmsvc_rqst->rq_server;
 	}
 
 	/*
@@ -451,17 +371,44 @@
 		nlm_timeout = LOCKD_DFLT_TIMEO;
 	nlmsvc_timeout = nlm_timeout * HZ;
 
-	serv = svc_create(&nlmsvc_program, LOCKD_BUFSIZE, &lockd_sv_ops);
+	serv = svc_create(&nlmsvc_program, LOCKD_BUFSIZE, lockd);
 	if (!serv) {
 		printk(KERN_WARNING "lockd_up: create service failed\n");
-		return ERR_PTR(-ENOMEM);
+		return -ENOMEM;
 	}
+
+	serv->sv_maxconn = nlm_max_connections;
+	error = svc_set_num_threads(serv, NULL, 1);
+	/* The thread now holds the only reference */
+	svc_put(serv);
+	if (error < 0)
+		return error;
+
+	nlmsvc_serv = serv;
 	register_inetaddr_notifier(&lockd_inetaddr_notifier);
 #if IS_ENABLED(CONFIG_IPV6)
 	register_inet6addr_notifier(&lockd_inet6addr_notifier);
 #endif
 	dprintk("lockd_up: service created\n");
-	return serv;
+	nlmsvc_users++;
+	return 0;
+}
+
+static void lockd_put(void)
+{
+	if (WARN(nlmsvc_users <= 0, "lockd_down: no users!\n"))
+		return;
+	if (--nlmsvc_users)
+		return;
+
+	unregister_inetaddr_notifier(&lockd_inetaddr_notifier);
+#if IS_ENABLED(CONFIG_IPV6)
+	unregister_inet6addr_notifier(&lockd_inet6addr_notifier);
+#endif
+
+	svc_set_num_threads(nlmsvc_serv, NULL, 0);
+	nlmsvc_serv = NULL;
+	dprintk("lockd_down: service destroyed\n");
 }
 
 /*
@@ -469,36 +416,21 @@
  */
 int lockd_up(struct net *net, const struct cred *cred)
 {
-	struct svc_serv *serv;
 	int error;
 
 	mutex_lock(&nlmsvc_mutex);
 
-	serv = lockd_create_svc();
-	if (IS_ERR(serv)) {
-		error = PTR_ERR(serv);
-		goto err_create;
-	}
+	error = lockd_get();
+	if (error)
+		goto err;
 
-	error = lockd_up_net(serv, net, cred);
+	error = lockd_up_net(nlmsvc_serv, net, cred);
 	if (error < 0) {
-		lockd_unregister_notifiers();
-		goto err_put;
+		lockd_put();
+		goto err;
 	}
 
-	error = lockd_start_svc(serv);
-	if (error < 0) {
-		lockd_down_net(serv, net);
-		goto err_put;
-	}
-	nlmsvc_users++;
-	/*
-	 * Note: svc_serv structures have an initial use count of 1,
-	 * so we exit through here on both success and failure.
-	 */
-err_put:
-	svc_destroy(serv);
-err_create:
+err:
 	mutex_unlock(&nlmsvc_mutex);
 	return error;
 }
@@ -511,27 +443,8 @@
 lockd_down(struct net *net)
 {
 	mutex_lock(&nlmsvc_mutex);
-	lockd_down_net(nlmsvc_rqst->rq_server, net);
-	if (nlmsvc_users) {
-		if (--nlmsvc_users)
-			goto out;
-	} else {
-		printk(KERN_ERR "lockd_down: no users! task=%p\n",
-			nlmsvc_task);
-		BUG();
-	}
-
-	if (!nlmsvc_task) {
-		printk(KERN_ERR "lockd_down: no lockd running.\n");
-		BUG();
-	}
-	kthread_stop(nlmsvc_task);
-	dprintk("lockd_down: service stopped\n");
-	lockd_svc_exit_thread();
-	dprintk("lockd_down: service destroyed\n");
-	nlmsvc_task = NULL;
-	nlmsvc_rqst = NULL;
-out:
+	lockd_down_net(nlmsvc_serv, net);
+	lockd_put();
 	mutex_unlock(&nlmsvc_mutex);
 }
 EXPORT_SYMBOL_GPL(lockd_down);
@@ -780,11 +693,9 @@
 static int nlmsvc_dispatch(struct svc_rqst *rqstp, __be32 *statp)
 {
 	const struct svc_procedure *procp = rqstp->rq_procinfo;
-	struct kvec *argv = rqstp->rq_arg.head;
-	struct kvec *resv = rqstp->rq_res.head;
 
 	svcxdr_init_decode(rqstp);
-	if (!procp->pc_decode(rqstp, argv->iov_base))
+	if (!procp->pc_decode(rqstp, &rqstp->rq_arg_stream))
 		goto out_decode_err;
 
 	*statp = procp->pc_func(rqstp);
@@ -794,7 +705,7 @@
 		return 1;
 
 	svcxdr_init_encode(rqstp);
-	if (!procp->pc_encode(rqstp, resv->iov_base + resv->iov_len))
+	if (!procp->pc_encode(rqstp, &rqstp->rq_res_stream))
 		goto out_encode_err;
 
 	return 1;
@@ -848,8 +759,6 @@
 #endif
 };
 
-static struct svc_stat		nlmsvc_stats;
-
 #define NLM_NRVERS	ARRAY_SIZE(nlmsvc_version)
 static struct svc_program	nlmsvc_program = {
 	.pg_prog		= NLM_PROGRAM,		/* program number */
@@ -857,7 +766,6 @@
 	.pg_vers		= nlmsvc_version,	/* version table */
 	.pg_name		= "lockd",		/* service name */
 	.pg_class		= "nfsd",		/* share authentication with nfsd */
-	.pg_stats		= &nlmsvc_stats,	/* stats table */
 	.pg_authenticate	= &lockd_authenticate,	/* export authentication */
 	.pg_init_request	= svc_generic_init_request,
 	.pg_rpcbind_set		= svc_generic_rpcbind_set,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/svc4proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/svc4proc.c
@@ -32,6 +32,10 @@
 	if (!nlmsvc_ops)
 		return nlm_lck_denied_nolocks;
 
+	if (lock->lock_start > OFFSET_MAX ||
+	    (lock->lock_len && ((lock->lock_len - 1) > (OFFSET_MAX - lock->lock_start))))
+		return nlm4_fbig;
+
 	/* Obtain host handle */
 	if (!(host = nlmsvc_lookup_host(rqstp, lock->caller, lock->len))
 	 || (argp->monitor && nsm_monitor(host) < 0))
@@ -48,8 +52,13 @@
 		*filp = file;
 
 		/* Set up the missing parts of the file_lock structure */
+		lock->fl.fl_flags = FL_POSIX;
 		lock->fl.fl_file  = file->f_file[mode];
 		lock->fl.fl_pid = current->tgid;
+		lock->fl.fl_start = (loff_t)lock->lock_start;
+		lock->fl.fl_end = lock->lock_len ?
+				   (loff_t)(lock->lock_start + lock->lock_len - 1) :
+				   OFFSET_MAX;
 		lock->fl.fl_lmops = &nlmsvc_lock_operations;
 		nlmsvc_locks_init_private(&lock->fl, host, (pid_t)lock->svid);
 		if (!lock->fl.fl_owner) {
@@ -87,6 +96,7 @@
 	struct nlm_args *argp = rqstp->rq_argp;
 	struct nlm_host	*host;
 	struct nlm_file	*file;
+	struct nlm_lockowner *test_owner;
 	__be32 rc = rpc_success;
 
 	dprintk("lockd: TEST4        called\n");
@@ -96,6 +106,7 @@
 	if ((resp->status = nlm4svc_retrieve_args(rqstp, argp, &host, &file)))
 		return resp->status == nlm_drop_reply ? rpc_drop_reply :rpc_success;
 
+	test_owner = argp->lock.fl.fl_owner;
 	/* Now check for conflicting locks */
 	resp->status = nlmsvc_testlock(rqstp, file, host, &argp->lock, &resp->lock, &resp->cookie);
 	if (resp->status == nlm_drop_reply)
@@ -103,7 +114,7 @@
 	else
 		dprintk("lockd: TEST4        status %d\n", ntohl(resp->status));
 
-	nlmsvc_release_lockowner(&argp->lock);
+	nlmsvc_put_lockowner(test_owner);
 	nlmsvc_release_host(host);
 	nlm_release_file(file);
 	return rc;
@@ -513,6 +524,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "NULL",
@@ -522,6 +534,7 @@
 		.pc_decode = nlm4svc_decode_testargs,
 		.pc_encode = nlm4svc_encode_testres,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St+2+No+Rg,
 		.pc_name = "TEST",
@@ -531,6 +544,7 @@
 		.pc_decode = nlm4svc_decode_lockargs,
 		.pc_encode = nlm4svc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "LOCK",
@@ -540,6 +554,7 @@
 		.pc_decode = nlm4svc_decode_cancargs,
 		.pc_encode = nlm4svc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "CANCEL",
@@ -549,6 +564,7 @@
 		.pc_decode = nlm4svc_decode_unlockargs,
 		.pc_encode = nlm4svc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "UNLOCK",
@@ -558,6 +574,7 @@
 		.pc_decode = nlm4svc_decode_testargs,
 		.pc_encode = nlm4svc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "GRANTED",
@@ -567,6 +584,7 @@
 		.pc_decode = nlm4svc_decode_testargs,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "TEST_MSG",
@@ -576,6 +594,7 @@
 		.pc_decode = nlm4svc_decode_lockargs,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "LOCK_MSG",
@@ -585,6 +604,7 @@
 		.pc_decode = nlm4svc_decode_cancargs,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "CANCEL_MSG",
@@ -594,6 +614,7 @@
 		.pc_decode = nlm4svc_decode_unlockargs,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNLOCK_MSG",
@@ -603,6 +624,7 @@
 		.pc_decode = nlm4svc_decode_testargs,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "GRANTED_MSG",
@@ -612,6 +634,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "TEST_RES",
@@ -621,6 +644,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "LOCK_RES",
@@ -630,6 +654,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "CANCEL_RES",
@@ -639,6 +664,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNLOCK_RES",
@@ -648,6 +674,7 @@
 		.pc_decode = nlm4svc_decode_res,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "GRANTED_RES",
@@ -657,6 +684,7 @@
 		.pc_decode = nlm4svc_decode_reboot,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_reboot),
+		.pc_argzero = sizeof(struct nlm_reboot),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "SM_NOTIFY",
@@ -666,6 +694,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = 0,
 		.pc_name = "UNUSED",
@@ -675,6 +704,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = 0,
 		.pc_name = "UNUSED",
@@ -684,6 +714,7 @@
 		.pc_decode = nlm4svc_decode_void,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = 0,
 		.pc_name = "UNUSED",
@@ -693,6 +724,7 @@
 		.pc_decode = nlm4svc_decode_shareargs,
 		.pc_encode = nlm4svc_encode_shareres,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St+1,
 		.pc_name = "SHARE",
@@ -702,6 +734,7 @@
 		.pc_decode = nlm4svc_decode_shareargs,
 		.pc_encode = nlm4svc_encode_shareres,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St+1,
 		.pc_name = "UNSHARE",
@@ -711,6 +744,7 @@
 		.pc_decode = nlm4svc_decode_lockargs,
 		.pc_encode = nlm4svc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "NM_LOCK",
@@ -720,6 +754,7 @@
 		.pc_decode = nlm4svc_decode_notify,
 		.pc_encode = nlm4svc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "FREE_ALL",
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/svclock.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/svclock.c
@@ -340,7 +340,7 @@
 	return lockowner;
 }
 
-static void nlmsvc_put_lockowner(struct nlm_lockowner *lockowner)
+void nlmsvc_put_lockowner(struct nlm_lockowner *lockowner)
 {
 	if (!refcount_dec_and_lock(&lockowner->count, &lockowner->host->h_lock))
 		return;
@@ -470,8 +470,10 @@
 	    struct nlm_host *host, struct nlm_lock *lock, int wait,
 	    struct nlm_cookie *cookie, int reclaim)
 {
-	struct nlm_block	*block = NULL;
+#if IS_ENABLED(CONFIG_SUNRPC_DEBUG)
 	struct inode		*inode = nlmsvc_file_inode(file);
+#endif
+	struct nlm_block	*block = NULL;
 	int			error;
 	int			mode;
 	int			async_block = 0;
@@ -484,7 +486,7 @@
 				(long long)lock->fl.fl_end,
 				wait);
 
-	if (inode->i_sb->s_export_op->flags & EXPORT_OP_SYNC_LOCKS) {
+	if (nlmsvc_file_file(file)->f_op->lock) {
 		async_block = wait;
 		wait = 0;
 	}
@@ -588,7 +590,6 @@
 	int			error;
 	int			mode;
 	__be32			ret;
-	struct nlm_lockowner	*test_owner;
 
 	dprintk("lockd: nlmsvc_testlock(%s/%ld, ty=%d, %Ld-%Ld)\n",
 				nlmsvc_file_inode(file)->i_sb->s_id,
@@ -602,9 +603,6 @@
 		goto out;
 	}
 
-	/* If there's a conflicting lock, remember to clean up the test lock */
-	test_owner = (struct nlm_lockowner *)lock->fl.fl_owner;
-
 	mode = lock_to_openmode(&lock->fl);
 	error = vfs_test_lock(file->f_file[mode], &lock->fl);
 	if (error) {
@@ -633,10 +631,6 @@
 	conflock->fl.fl_end = lock->fl.fl_end;
 	locks_release_private(&lock->fl);
 
-	/* Clean up the test lock */
-	lock->fl.fl_owner = NULL;
-	nlmsvc_put_lockowner(test_owner);
-
 	ret = nlm_lck_denied;
 out:
 	return ret;
@@ -665,11 +659,13 @@
 	nlmsvc_cancel_blocked(net, file, lock);
 
 	lock->fl.fl_type = F_UNLCK;
-	if (file->f_file[O_RDONLY])
-		error = vfs_lock_file(file->f_file[O_RDONLY], F_SETLK,
+	lock->fl.fl_file = file->f_file[O_RDONLY];
+	if (lock->fl.fl_file)
+		error = vfs_lock_file(lock->fl.fl_file, F_SETLK,
 					&lock->fl, NULL);
-	if (file->f_file[O_WRONLY])
-		error = vfs_lock_file(file->f_file[O_WRONLY], F_SETLK,
+	lock->fl.fl_file = file->f_file[O_WRONLY];
+	if (lock->fl.fl_file)
+		error |= vfs_lock_file(lock->fl.fl_file, F_SETLK,
 					&lock->fl, NULL);
 
 	return (error < 0)? nlm_lck_denied_nolocks : nlm_granted;
@@ -703,9 +699,10 @@
 	block = nlmsvc_lookup_block(file, lock);
 	mutex_unlock(&file->f_mutex);
 	if (block != NULL) {
-		mode = lock_to_openmode(&lock->fl);
-		vfs_cancel_lock(block->b_file->f_file[mode],
-				&block->b_call->a_args.lock.fl);
+		struct file_lock *fl = &block->b_call->a_args.lock.fl;
+
+		mode = lock_to_openmode(fl);
+		vfs_cancel_lock(block->b_file->f_file[mode], fl);
 		status = nlmsvc_unlink_block(block);
 		nlmsvc_release_block(block);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/svcproc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/svcproc.c
@@ -77,6 +77,7 @@
 
 		/* Set up the missing parts of the file_lock structure */
 		mode = lock_to_openmode(&lock->fl);
+		lock->fl.fl_flags = FL_POSIX;
 		lock->fl.fl_file  = file->f_file[mode];
 		lock->fl.fl_pid = current->tgid;
 		lock->fl.fl_lmops = &nlmsvc_lock_operations;
@@ -116,6 +117,7 @@
 	struct nlm_args *argp = rqstp->rq_argp;
 	struct nlm_host	*host;
 	struct nlm_file	*file;
+	struct nlm_lockowner *test_owner;
 	__be32 rc = rpc_success;
 
 	dprintk("lockd: TEST          called\n");
@@ -125,6 +127,8 @@
 	if ((resp->status = nlmsvc_retrieve_args(rqstp, argp, &host, &file)))
 		return resp->status == nlm_drop_reply ? rpc_drop_reply :rpc_success;
 
+	test_owner = argp->lock.fl.fl_owner;
+
 	/* Now check for conflicting locks */
 	resp->status = cast_status(nlmsvc_testlock(rqstp, file, host, &argp->lock, &resp->lock, &resp->cookie));
 	if (resp->status == nlm_drop_reply)
@@ -133,7 +137,7 @@
 		dprintk("lockd: TEST          status %d vers %d\n",
 			ntohl(resp->status), rqstp->rq_vers);
 
-	nlmsvc_release_lockowner(&argp->lock);
+	nlmsvc_put_lockowner(test_owner);
 	nlmsvc_release_host(host);
 	nlm_release_file(file);
 	return rc;
@@ -554,6 +558,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "NULL",
@@ -563,6 +568,7 @@
 		.pc_decode = nlmsvc_decode_testargs,
 		.pc_encode = nlmsvc_encode_testres,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St+2+No+Rg,
 		.pc_name = "TEST",
@@ -572,6 +578,7 @@
 		.pc_decode = nlmsvc_decode_lockargs,
 		.pc_encode = nlmsvc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "LOCK",
@@ -581,6 +588,7 @@
 		.pc_decode = nlmsvc_decode_cancargs,
 		.pc_encode = nlmsvc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "CANCEL",
@@ -590,6 +598,7 @@
 		.pc_decode = nlmsvc_decode_unlockargs,
 		.pc_encode = nlmsvc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "UNLOCK",
@@ -599,6 +608,7 @@
 		.pc_decode = nlmsvc_decode_testargs,
 		.pc_encode = nlmsvc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "GRANTED",
@@ -608,6 +618,7 @@
 		.pc_decode = nlmsvc_decode_testargs,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "TEST_MSG",
@@ -617,6 +628,7 @@
 		.pc_decode = nlmsvc_decode_lockargs,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "LOCK_MSG",
@@ -626,6 +638,7 @@
 		.pc_decode = nlmsvc_decode_cancargs,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "CANCEL_MSG",
@@ -635,6 +648,7 @@
 		.pc_decode = nlmsvc_decode_unlockargs,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNLOCK_MSG",
@@ -644,6 +658,7 @@
 		.pc_decode = nlmsvc_decode_testargs,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "GRANTED_MSG",
@@ -653,6 +668,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "TEST_RES",
@@ -662,6 +678,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "LOCK_RES",
@@ -671,6 +688,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "CANCEL_RES",
@@ -680,6 +698,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNLOCK_RES",
@@ -689,6 +708,7 @@
 		.pc_decode = nlmsvc_decode_res,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_res),
+		.pc_argzero = sizeof(struct nlm_res),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "GRANTED_RES",
@@ -698,6 +718,7 @@
 		.pc_decode = nlmsvc_decode_reboot,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_reboot),
+		.pc_argzero = sizeof(struct nlm_reboot),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "SM_NOTIFY",
@@ -707,6 +728,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNUSED",
@@ -716,6 +738,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNUSED",
@@ -725,6 +748,7 @@
 		.pc_decode = nlmsvc_decode_void,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_void),
+		.pc_argzero = sizeof(struct nlm_void),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = St,
 		.pc_name = "UNUSED",
@@ -734,6 +758,7 @@
 		.pc_decode = nlmsvc_decode_shareargs,
 		.pc_encode = nlmsvc_encode_shareres,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St+1,
 		.pc_name = "SHARE",
@@ -743,6 +768,7 @@
 		.pc_decode = nlmsvc_decode_shareargs,
 		.pc_encode = nlmsvc_encode_shareres,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St+1,
 		.pc_name = "UNSHARE",
@@ -752,6 +778,7 @@
 		.pc_decode = nlmsvc_decode_lockargs,
 		.pc_encode = nlmsvc_encode_res,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_res),
 		.pc_xdrressize = Ck+St,
 		.pc_name = "NM_LOCK",
@@ -761,6 +788,7 @@
 		.pc_decode = nlmsvc_decode_notify,
 		.pc_encode = nlmsvc_encode_void,
 		.pc_argsize = sizeof(struct nlm_args),
+		.pc_argzero = sizeof(struct nlm_args),
 		.pc_ressize = sizeof(struct nlm_void),
 		.pc_xdrressize = 0,
 		.pc_name = "FREE_ALL",
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/svcsubs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/svcsubs.c
@@ -176,22 +176,28 @@
 	}
 }
 
-static int nlm_unlock_files(struct nlm_file *file)
+static int nlm_unlock_files(struct nlm_file *file, const struct file_lock *fl)
 {
 	struct file_lock lock;
-	struct file *f;
 
+	locks_init_lock(&lock);
 	lock.fl_type  = F_UNLCK;
 	lock.fl_start = 0;
 	lock.fl_end   = OFFSET_MAX;
-	for (f = file->f_file[0]; f <= file->f_file[1]; f++) {
-		if (f && vfs_lock_file(f, F_SETLK, &lock, NULL) < 0) {
-			pr_warn("lockd: unlock failure in %s:%d\n",
-				__FILE__, __LINE__);
-			return 1;
-		}
-	}
+	lock.fl_owner = fl->fl_owner;
+	lock.fl_pid   = fl->fl_pid;
+	lock.fl_flags = FL_POSIX;
+
+	lock.fl_file = file->f_file[O_RDONLY];
+	if (lock.fl_file && vfs_lock_file(lock.fl_file, F_SETLK, &lock, NULL))
+		goto out_err;
+	lock.fl_file = file->f_file[O_WRONLY];
+	if (lock.fl_file && vfs_lock_file(lock.fl_file, F_SETLK, &lock, NULL))
+		goto out_err;
 	return 0;
+out_err:
+	pr_warn("lockd: unlock failure in %s:%d\n", __FILE__, __LINE__);
+	return 1;
 }
 
 /*
@@ -204,7 +210,7 @@
 {
 	struct inode	 *inode = nlmsvc_file_inode(file);
 	struct file_lock *fl;
-	struct file_lock_context *flctx = inode->i_flctx;
+	struct file_lock_context *flctx = locks_inode_context(inode);
 	struct nlm_host	 *lockhost;
 
 	if (!flctx || list_empty_careful(&flctx->flc_posix))
@@ -223,7 +229,7 @@
 		if (match(lockhost, host)) {
 
 			spin_unlock(&flctx->flc_lock);
-			if (nlm_unlock_files(file))
+			if (nlm_unlock_files(file, fl))
 				return 1;
 			goto again;
 		}
@@ -259,7 +265,7 @@
 {
 	struct inode	 *inode = nlmsvc_file_inode(file);
 	struct file_lock *fl;
-	struct file_lock_context *flctx = inode->i_flctx;
+	struct file_lock_context *flctx = locks_inode_context(inode);
 
 	if (file->f_count || !list_empty(&file->f_blocks) || file->f_shares)
 		return 1;
@@ -280,11 +286,10 @@
 
 static void nlm_close_files(struct nlm_file *file)
 {
-	struct file *f;
-
-	for (f = file->f_file[0]; f <= file->f_file[1]; f++)
-		if (f)
-			nlmsvc_ops->fclose(f);
+	if (file->f_file[O_RDONLY])
+		nlmsvc_ops->fclose(file->f_file[O_RDONLY]);
+	if (file->f_file[O_WRONLY])
+		nlmsvc_ops->fclose(file->f_file[O_WRONLY]);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/xdr.c
@@ -145,137 +145,131 @@
  * Decode Call arguments
  */
 
-int
-nlmsvc_decode_void(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_testargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_testargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	u32 exclusive;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &exclusive) < 0)
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	if (exclusive)
 		argp->lock.fl.fl_type = F_WRLCK;
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_lockargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_lockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	u32 exclusive;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &argp->block) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &exclusive) < 0)
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	if (exclusive)
 		argp->lock.fl.fl_type = F_WRLCK;
 	if (xdr_stream_decode_bool(xdr, &argp->reclaim) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->state) < 0)
-		return 0;
+		return false;
 	argp->monitor = 1;		/* monitor client by default */
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_cancargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_cancargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	u32 exclusive;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &argp->block) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &exclusive) < 0)
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	if (exclusive)
 		argp->lock.fl.fl_type = F_WRLCK;
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_unlockargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_unlockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	argp->lock.fl.fl_type = F_UNLCK;
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_res(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_res *resp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_cookie(xdr, &resp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_decode_stats(xdr, &resp->status))
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_reboot(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_reboot(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_reboot *argp = rqstp->rq_argp;
+	__be32 *p;
 	u32 len;
 
 	if (xdr_stream_decode_u32(xdr, &len) < 0)
-		return 0;
+		return false;
 	if (len > SM_MAXSTRLEN)
-		return 0;
+		return false;
 	p = xdr_inline_decode(xdr, len);
 	if (!p)
-		return 0;
+		return false;
 	argp->len = len;
 	argp->mon = (char *)p;
 	if (xdr_stream_decode_u32(xdr, &argp->state) < 0)
-		return 0;
+		return false;
 	p = xdr_inline_decode(xdr, SM_PRIV_SIZE);
 	if (!p)
-		return 0;
+		return false;
 	memcpy(&argp->priv.data, p, sizeof(argp->priv.data));
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_shareargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_shareargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	struct nlm_lock	*lock = &argp->lock;
 
@@ -284,35 +278,34 @@
 	lock->svid = ~(u32)0;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_decode_string(xdr, &lock->caller, &lock->len))
-		return 0;
+		return false;
 	if (!svcxdr_decode_fhandle(xdr, &lock->fh))
-		return 0;
+		return false;
 	if (!svcxdr_decode_owner(xdr, &lock->oh))
-		return 0;
+		return false;
 	/* XXX: Range checks are missing in the original code */
 	if (xdr_stream_decode_u32(xdr, &argp->fsm_mode) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->fsm_access) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_decode_notify(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_decode_notify(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	struct nlm_lock	*lock = &argp->lock;
 
 	if (!svcxdr_decode_string(xdr, &lock->caller, &lock->len))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->state) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 
@@ -320,45 +313,42 @@
  * Encode Reply results
  */
 
-int
-nlmsvc_encode_void(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_encode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return 1;
+	return true;
 }
 
-int
-nlmsvc_encode_testres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_encode_testres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nlm_res *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_cookie(xdr, &resp->cookie) &&
 		svcxdr_encode_testrply(xdr, resp);
 }
 
-int
-nlmsvc_encode_res(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_encode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nlm_res *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_cookie(xdr, &resp->cookie) &&
 		svcxdr_encode_stats(xdr, resp->status);
 }
 
-int
-nlmsvc_encode_shareres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlmsvc_encode_shareres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nlm_res *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_cookie(xdr, &resp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_encode_stats(xdr, resp->status))
-		return 0;
+		return false;
 	/* sequence */
 	if (xdr_stream_encode_u32(xdr, 0) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/lockd/xdr4.c
+++ linux-xilinx-zynqmp-5.15.0/fs/lockd/xdr4.c
@@ -20,13 +20,6 @@
 
 #include "svcxdr.h"
 
-static inline loff_t
-s64_to_loff_t(__s64 offset)
-{
-	return (loff_t)offset;
-}
-
-
 static inline s64
 loff_t_to_s64(loff_t offset)
 {
@@ -40,6 +33,17 @@
 	return res;
 }
 
+void nlm4svc_set_file_lock_range(struct file_lock *fl, u64 off, u64 len)
+{
+	s64 end = off + len - 1;
+
+	fl->fl_start = off;
+	if (len == 0 || end < 0)
+		fl->fl_end = OFFSET_MAX;
+	else
+		fl->fl_end = end;
+}
+
 /*
  * NLM file handles are defined by specification to be a variable-length
  * XDR opaque no longer than 1024 bytes. However, this implementation
@@ -70,8 +74,6 @@
 svcxdr_decode_lock(struct xdr_stream *xdr, struct nlm_lock *lock)
 {
 	struct file_lock *fl = &lock->fl;
-	u64 len, start;
-	s64 end;
 
 	if (!svcxdr_decode_string(xdr, &lock->caller, &lock->len))
 		return false;
@@ -81,21 +83,15 @@
 		return false;
 	if (xdr_stream_decode_u32(xdr, &lock->svid) < 0)
 		return false;
-	if (xdr_stream_decode_u64(xdr, &start) < 0)
+	if (xdr_stream_decode_u64(xdr, &lock->lock_start) < 0)
 		return false;
-	if (xdr_stream_decode_u64(xdr, &len) < 0)
+	if (xdr_stream_decode_u64(xdr, &lock->lock_len) < 0)
 		return false;
 
 	locks_init_lock(fl);
 	fl->fl_flags = FL_POSIX;
 	fl->fl_type  = F_RDLCK;
-	end = start + len - 1;
-	fl->fl_start = s64_to_loff_t(start);
-	if (len == 0 || end < 0)
-		fl->fl_end = OFFSET_MAX;
-	else
-		fl->fl_end = s64_to_loff_t(end);
-
+	nlm4svc_set_file_lock_range(fl, lock->lock_start, lock->lock_len);
 	return true;
 }
 
@@ -144,136 +140,131 @@
  * Decode Call arguments
  */
 
-int
-nlm4svc_decode_void(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_testargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_testargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	u32 exclusive;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &exclusive) < 0)
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	if (exclusive)
 		argp->lock.fl.fl_type = F_WRLCK;
 
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_lockargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_lockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	u32 exclusive;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &argp->block) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &exclusive) < 0)
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	if (exclusive)
 		argp->lock.fl.fl_type = F_WRLCK;
 	if (xdr_stream_decode_bool(xdr, &argp->reclaim) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->state) < 0)
-		return 0;
+		return false;
 	argp->monitor = 1;		/* monitor client by default */
 
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_cancargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_cancargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	u32 exclusive;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &argp->block) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_bool(xdr, &exclusive) < 0)
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	if (exclusive)
 		argp->lock.fl.fl_type = F_WRLCK;
-	return 1;
+
+	return true;
 }
 
-int
-nlm4svc_decode_unlockargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_unlockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_decode_lock(xdr, &argp->lock))
-		return 0;
+		return false;
 	argp->lock.fl.fl_type = F_UNLCK;
 
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_res(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_res *resp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_cookie(xdr, &resp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_decode_stats(xdr, &resp->status))
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_reboot(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_reboot(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_reboot *argp = rqstp->rq_argp;
+	__be32 *p;
 	u32 len;
 
 	if (xdr_stream_decode_u32(xdr, &len) < 0)
-		return 0;
+		return false;
 	if (len > SM_MAXSTRLEN)
-		return 0;
+		return false;
 	p = xdr_inline_decode(xdr, len);
 	if (!p)
-		return 0;
+		return false;
 	argp->len = len;
 	argp->mon = (char *)p;
 	if (xdr_stream_decode_u32(xdr, &argp->state) < 0)
-		return 0;
+		return false;
 	p = xdr_inline_decode(xdr, SM_PRIV_SIZE);
 	if (!p)
-		return 0;
+		return false;
 	memcpy(&argp->priv.data, p, sizeof(argp->priv.data));
 
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_shareargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_shareargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	struct nlm_lock	*lock = &argp->lock;
 
@@ -282,35 +273,34 @@
 	lock->svid = ~(u32)0;
 
 	if (!svcxdr_decode_cookie(xdr, &argp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_decode_string(xdr, &lock->caller, &lock->len))
-		return 0;
+		return false;
 	if (!svcxdr_decode_fhandle(xdr, &lock->fh))
-		return 0;
+		return false;
 	if (!svcxdr_decode_owner(xdr, &lock->oh))
-		return 0;
+		return false;
 	/* XXX: Range checks are missing in the original code */
 	if (xdr_stream_decode_u32(xdr, &argp->fsm_mode) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->fsm_access) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_decode_notify(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_decode_notify(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nlm_args *argp = rqstp->rq_argp;
 	struct nlm_lock	*lock = &argp->lock;
 
 	if (!svcxdr_decode_string(xdr, &lock->caller, &lock->len))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->state) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 
@@ -318,45 +308,42 @@
  * Encode Reply results
  */
 
-int
-nlm4svc_encode_void(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_encode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return 1;
+	return true;
 }
 
-int
-nlm4svc_encode_testres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_encode_testres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nlm_res *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_cookie(xdr, &resp->cookie) &&
 		svcxdr_encode_testrply(xdr, resp);
 }
 
-int
-nlm4svc_encode_res(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_encode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nlm_res *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_cookie(xdr, &resp->cookie) &&
 		svcxdr_encode_stats(xdr, resp->status);
 }
 
-int
-nlm4svc_encode_shareres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nlm4svc_encode_shareres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nlm_res *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_cookie(xdr, &resp->cookie))
-		return 0;
+		return false;
 	if (!svcxdr_encode_stats(xdr, resp->status))
-		return 0;
+		return false;
 	/* sequence */
 	if (xdr_stream_encode_u32(xdr, 0) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/locks.c
+++ linux-xilinx-zynqmp-5.15.0/fs/locks.c
@@ -251,7 +251,7 @@
 	struct file_lock_context *ctx;
 
 	/* paired with cmpxchg() below */
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (likely(ctx) || type == F_UNLCK)
 		goto out;
 
@@ -270,7 +270,7 @@
 	 */
 	if (cmpxchg(&inode->i_flctx, NULL, ctx)) {
 		kmem_cache_free(flctx_cache, ctx);
-		ctx = smp_load_acquire(&inode->i_flctx);
+		ctx = locks_inode_context(inode);
 	}
 out:
 	trace_locks_get_lock_context(inode, type, ctx);
@@ -323,7 +323,7 @@
 void
 locks_free_lock_context(struct inode *inode)
 {
-	struct file_lock_context *ctx = inode->i_flctx;
+	struct file_lock_context *ctx = locks_inode_context(inode);
 
 	if (unlikely(ctx)) {
 		locks_check_ctx_lists(inode);
@@ -376,6 +376,34 @@
 }
 EXPORT_SYMBOL_GPL(locks_release_private);
 
+/**
+ * locks_owner_has_blockers - Check for blocking lock requests
+ * @flctx: file lock context
+ * @owner: lock owner
+ *
+ * Return values:
+ *   %true: @owner has at least one blocker
+ *   %false: @owner has no blockers
+ */
+bool locks_owner_has_blockers(struct file_lock_context *flctx,
+		fl_owner_t owner)
+{
+	struct file_lock *fl;
+
+	spin_lock(&flctx->flc_lock);
+	list_for_each_entry(fl, &flctx->flc_posix, fl_list) {
+		if (fl->fl_owner != owner)
+			continue;
+		if (!list_empty(&fl->fl_blocked_requests)) {
+			spin_unlock(&flctx->flc_lock);
+			return true;
+		}
+	}
+	spin_unlock(&flctx->flc_lock);
+	return false;
+}
+EXPORT_SYMBOL_GPL(locks_owner_has_blockers);
+
 /* Free a lock which is not in use. */
 void locks_free_lock(struct file_lock *fl)
 {
@@ -954,19 +982,32 @@
 	struct file_lock *cfl;
 	struct file_lock_context *ctx;
 	struct inode *inode = locks_inode(filp);
+	void *owner;
+	void (*func)(void);
 
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (!ctx || list_empty_careful(&ctx->flc_posix)) {
 		fl->fl_type = F_UNLCK;
 		return;
 	}
 
+retry:
 	spin_lock(&ctx->flc_lock);
 	list_for_each_entry(cfl, &ctx->flc_posix, fl_list) {
-		if (posix_locks_conflict(fl, cfl)) {
-			locks_copy_conflock(fl, cfl);
-			goto out;
+		if (!posix_locks_conflict(fl, cfl))
+			continue;
+		if (cfl->fl_lmops && cfl->fl_lmops->lm_lock_expirable
+			&& (*cfl->fl_lmops->lm_lock_expirable)(cfl)) {
+			owner = cfl->fl_lmops->lm_mod_owner;
+			func = cfl->fl_lmops->lm_expire_lock;
+			__module_get(owner);
+			spin_unlock(&ctx->flc_lock);
+			(*func)();
+			module_put(owner);
+			goto retry;
 		}
+		locks_copy_conflock(fl, cfl);
+		goto out;
 	}
 	fl->fl_type = F_UNLCK;
 out:
@@ -1140,6 +1181,8 @@
 	int error;
 	bool added = false;
 	LIST_HEAD(dispose);
+	void *owner;
+	void (*func)(void);
 
 	ctx = locks_get_lock_context(inode, request->fl_type);
 	if (!ctx)
@@ -1158,6 +1201,7 @@
 		new_fl2 = locks_alloc_lock();
 	}
 
+retry:
 	percpu_down_read(&file_rwsem);
 	spin_lock(&ctx->flc_lock);
 	/*
@@ -1169,6 +1213,17 @@
 		list_for_each_entry(fl, &ctx->flc_posix, fl_list) {
 			if (!posix_locks_conflict(request, fl))
 				continue;
+			if (fl->fl_lmops && fl->fl_lmops->lm_lock_expirable
+				&& (*fl->fl_lmops->lm_lock_expirable)(fl)) {
+				owner = fl->fl_lmops->lm_mod_owner;
+				func = fl->fl_lmops->lm_expire_lock;
+				__module_get(owner);
+				spin_unlock(&ctx->flc_lock);
+				percpu_up_read(&file_rwsem);
+				(*func)();
+				module_put(owner);
+				goto retry;
+			}
 			if (conflock)
 				locks_copy_conflock(conflock, fl);
 			error = -EAGAIN;
@@ -1337,6 +1392,7 @@
 		locks_wake_up_blocks(left);
 	}
  out:
+	trace_posix_lock_inode(inode, request, error);
 	spin_unlock(&ctx->flc_lock);
 	percpu_up_read(&file_rwsem);
 	/*
@@ -1347,7 +1403,6 @@
 	if (new_fl2)
 		locks_free_lock(new_fl2);
 	locks_dispose_list(&dispose);
-	trace_posix_lock_inode(inode, request, error);
 
 	return error;
 }
@@ -1522,7 +1577,7 @@
 	new_fl->fl_flags = type;
 
 	/* typically we will check that ctx is non-NULL before calling */
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (!ctx) {
 		WARN_ON_ONCE(1);
 		goto free_lock;
@@ -1627,7 +1682,7 @@
 	struct file_lock_context *ctx;
 	struct file_lock *fl;
 
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (ctx && !list_empty_careful(&ctx->flc_lease)) {
 		spin_lock(&ctx->flc_lock);
 		fl = list_first_entry_or_null(&ctx->flc_lease,
@@ -1673,7 +1728,7 @@
 	int type = F_UNLCK;
 	LIST_HEAD(dispose);
 
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (ctx && !list_empty_careful(&ctx->flc_lease)) {
 		percpu_down_read(&file_rwsem);
 		spin_lock(&ctx->flc_lock);
@@ -1862,7 +1917,7 @@
 	struct file_lock_context *ctx;
 	LIST_HEAD(dispose);
 
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (!ctx) {
 		trace_generic_delete_lease(inode, NULL);
 		return error;
@@ -1901,9 +1956,10 @@
 			void **priv)
 {
 	struct inode *inode = locks_inode(filp);
+	kuid_t uid = i_uid_into_mnt(file_mnt_user_ns(filp), inode);
 	int error;
 
-	if ((!uid_eq(current_fsuid(), inode->i_uid)) && !capable(CAP_LEASE))
+	if ((!uid_eq(current_fsuid(), uid)) && !capable(CAP_LEASE))
 		return -EACCES;
 	if (!S_ISREG(inode->i_mode))
 		return -EINVAL;
@@ -2427,8 +2483,9 @@
 	error = do_lock_file_wait(filp, cmd, file_lock);
 
 	/*
-	 * Attempt to detect a close/fcntl race and recover by releasing the
-	 * lock that was just acquired. There is no need to do that when we're
+	 * Detect close/fcntl races and recover by zapping all POSIX locks
+	 * associated with this file and our files_struct, just like on
+	 * filp_flush(). There is no need to do that when we're
 	 * unlocking though, or for OFD locks.
 	 */
 	if (!error && file_lock->fl_type != F_UNLCK &&
@@ -2443,9 +2500,7 @@
 		f = files_lookup_fd_locked(files, fd);
 		spin_unlock(&files->file_lock);
 		if (f != filp) {
-			file_lock->fl_type = F_UNLCK;
-			error = do_lock_file_wait(filp, cmd, file_lock);
-			WARN_ON_ONCE(error);
+			locks_remove_posix(filp, files);
 			error = -EBADF;
 		}
 	}
@@ -2550,8 +2605,9 @@
 	error = do_lock_file_wait(filp, cmd, file_lock);
 
 	/*
-	 * Attempt to detect a close/fcntl race and recover by releasing the
-	 * lock that was just acquired. There is no need to do that when we're
+	 * Detect close/fcntl races and recover by zapping all POSIX locks
+	 * associated with this file and our files_struct, just like on
+	 * filp_flush(). There is no need to do that when we're
 	 * unlocking though, or for OFD locks.
 	 */
 	if (!error && file_lock->fl_type != F_UNLCK &&
@@ -2566,9 +2622,7 @@
 		f = files_lookup_fd_locked(files, fd);
 		spin_unlock(&files->file_lock);
 		if (f != filp) {
-			file_lock->fl_type = F_UNLCK;
-			error = do_lock_file_wait(filp, cmd, file_lock);
-			WARN_ON_ONCE(error);
+			locks_remove_posix(filp, files);
 			error = -EBADF;
 		}
 	}
@@ -2595,7 +2649,7 @@
 	 * posix_lock_file().  Another process could be setting a lock on this
 	 * file at the same time, but we wouldn't remove that lock anyway.
 	 */
-	ctx =  smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (!ctx || list_empty(&ctx->flc_posix))
 		return;
 
@@ -2668,7 +2722,7 @@
 {
 	struct file_lock_context *ctx;
 
-	ctx = smp_load_acquire(&locks_inode(filp)->i_flctx);
+	ctx = locks_inode_context(locks_inode(filp));
 	if (!ctx)
 		return;
 
@@ -2703,6 +2757,29 @@
 }
 EXPORT_SYMBOL_GPL(vfs_cancel_lock);
 
+/**
+ * vfs_inode_has_locks - are any file locks held on @inode?
+ * @inode: inode to check for locks
+ *
+ * Return true if there are any FL_POSIX or FL_FLOCK locks currently
+ * set on @inode.
+ */
+bool vfs_inode_has_locks(struct inode *inode)
+{
+	struct file_lock_context *ctx;
+	bool ret;
+
+	ctx = locks_inode_context(inode);
+	if (!ctx)
+		return false;
+
+	spin_lock(&ctx->flc_lock);
+	ret = !list_empty(&ctx->flc_posix) || !list_empty(&ctx->flc_flock);
+	spin_unlock(&ctx->flc_lock);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(vfs_inode_has_locks);
+
 #ifdef CONFIG_PROC_FS
 #include <linux/proc_fs.h>
 #include <linux/seq_file.h>
@@ -2883,7 +2960,7 @@
 	struct file_lock_context *ctx;
 	int id = 0;
 
-	ctx = smp_load_acquire(&inode->i_flctx);
+	ctx = locks_inode_context(inode);
 	if (!ctx)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/mbcache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/mbcache.c
@@ -11,7 +11,7 @@
 /*
  * Mbcache is a simple key-value store. Keys need not be unique, however
  * key-value pairs are expected to be unique (we use this fact in
- * mb_cache_entry_delete()).
+ * mb_cache_entry_delete_or_get()).
  *
  * Ext2 and ext4 use this cache for deduplication of extended attribute blocks.
  * Ext4 also uses it for deduplication of xattr values stored in inodes.
@@ -90,12 +90,19 @@
 		return -ENOMEM;
 
 	INIT_LIST_HEAD(&entry->e_list);
-	/* One ref for hash, one ref returned */
-	atomic_set(&entry->e_refcnt, 1);
+	/*
+	 * We create entry with two references. One reference is kept by the
+	 * hash table, the other reference is used to protect us from
+	 * mb_cache_entry_delete_or_get() until the entry is fully setup. This
+	 * avoids nesting of cache->c_list_lock into hash table bit locks which
+	 * is problematic for RT.
+	 */
+	atomic_set(&entry->e_refcnt, 2);
 	entry->e_key = key;
 	entry->e_value = value;
-	entry->e_reusable = reusable;
-	entry->e_referenced = 0;
+	entry->e_flags = 0;
+	if (reusable)
+		set_bit(MBE_REUSABLE_B, &entry->e_flags);
 	head = mb_cache_entry_head(cache, key);
 	hlist_bl_lock(head);
 	hlist_bl_for_each_entry(dup, dup_node, head, e_hash_list) {
@@ -107,24 +114,41 @@
 	}
 	hlist_bl_add_head(&entry->e_hash_list, head);
 	hlist_bl_unlock(head);
-
 	spin_lock(&cache->c_list_lock);
 	list_add_tail(&entry->e_list, &cache->c_list);
-	/* Grab ref for LRU list */
-	atomic_inc(&entry->e_refcnt);
 	cache->c_entry_count++;
 	spin_unlock(&cache->c_list_lock);
+	mb_cache_entry_put(cache, entry);
 
 	return 0;
 }
 EXPORT_SYMBOL(mb_cache_entry_create);
 
-void __mb_cache_entry_free(struct mb_cache_entry *entry)
+void __mb_cache_entry_free(struct mb_cache *cache, struct mb_cache_entry *entry)
 {
+	struct hlist_bl_head *head;
+
+	head = mb_cache_entry_head(cache, entry->e_key);
+	hlist_bl_lock(head);
+	hlist_bl_del(&entry->e_hash_list);
+	hlist_bl_unlock(head);
 	kmem_cache_free(mb_entry_cache, entry);
 }
 EXPORT_SYMBOL(__mb_cache_entry_free);
 
+/*
+ * mb_cache_entry_wait_unused - wait to be the last user of the entry
+ *
+ * @entry - entry to work on
+ *
+ * Wait to be the last user of the entry.
+ */
+void mb_cache_entry_wait_unused(struct mb_cache_entry *entry)
+{
+	wait_var_event(&entry->e_refcnt, atomic_read(&entry->e_refcnt) <= 2);
+}
+EXPORT_SYMBOL(mb_cache_entry_wait_unused);
+
 static struct mb_cache_entry *__entry_find(struct mb_cache *cache,
 					   struct mb_cache_entry *entry,
 					   u32 key)
@@ -142,10 +166,10 @@
 	while (node) {
 		entry = hlist_bl_entry(node, struct mb_cache_entry,
 				       e_hash_list);
-		if (entry->e_key == key && entry->e_reusable) {
-			atomic_inc(&entry->e_refcnt);
+		if (entry->e_key == key &&
+		    test_bit(MBE_REUSABLE_B, &entry->e_flags) &&
+		    atomic_inc_not_zero(&entry->e_refcnt))
 			goto out;
-		}
 		node = node->next;
 	}
 	entry = NULL;
@@ -205,10 +229,9 @@
 	head = mb_cache_entry_head(cache, key);
 	hlist_bl_lock(head);
 	hlist_bl_for_each_entry(entry, node, head, e_hash_list) {
-		if (entry->e_key == key && entry->e_value == value) {
-			atomic_inc(&entry->e_refcnt);
+		if (entry->e_key == key && entry->e_value == value &&
+		    atomic_inc_not_zero(&entry->e_refcnt))
 			goto out;
-		}
 	}
 	entry = NULL;
 out:
@@ -217,7 +240,7 @@
 }
 EXPORT_SYMBOL(mb_cache_entry_get);
 
-/* mb_cache_entry_delete - remove a cache entry
+/* mb_cache_entry_delete - try to remove a cache entry
  * @cache - cache we work with
  * @key - key
  * @value - value
@@ -254,6 +277,43 @@
 }
 EXPORT_SYMBOL(mb_cache_entry_delete);
 
+/* mb_cache_entry_delete_or_get - remove a cache entry if it has no users
+ * @cache - cache we work with
+ * @key - key
+ * @value - value
+ *
+ * Remove entry from cache @cache with key @key and value @value. The removal
+ * happens only if the entry is unused. The function returns NULL in case the
+ * entry was successfully removed or there's no entry in cache. Otherwise the
+ * function grabs reference of the entry that we failed to delete because it
+ * still has users and return it.
+ */
+struct mb_cache_entry *mb_cache_entry_delete_or_get(struct mb_cache *cache,
+						    u32 key, u64 value)
+{
+	struct mb_cache_entry *entry;
+
+	entry = mb_cache_entry_get(cache, key, value);
+	if (!entry)
+		return NULL;
+
+	/*
+	 * Drop the ref we got from mb_cache_entry_get() and the initial hash
+	 * ref if we are the last user
+	 */
+	if (atomic_cmpxchg(&entry->e_refcnt, 2, 0) != 2)
+		return entry;
+
+	spin_lock(&cache->c_list_lock);
+	if (!list_empty(&entry->e_list))
+		list_del_init(&entry->e_list);
+	cache->c_entry_count--;
+	spin_unlock(&cache->c_list_lock);
+	__mb_cache_entry_free(cache, entry);
+	return NULL;
+}
+EXPORT_SYMBOL(mb_cache_entry_delete_or_get);
+
 /* mb_cache_entry_touch - cache entry got used
  * @cache - cache the entry belongs to
  * @entry - entry that got used
@@ -263,7 +323,7 @@
 void mb_cache_entry_touch(struct mb_cache *cache,
 			  struct mb_cache_entry *entry)
 {
-	entry->e_referenced = 1;
+	set_bit(MBE_REFERENCED_B, &entry->e_flags);
 }
 EXPORT_SYMBOL(mb_cache_entry_touch);
 
@@ -281,34 +341,24 @@
 				     unsigned long nr_to_scan)
 {
 	struct mb_cache_entry *entry;
-	struct hlist_bl_head *head;
 	unsigned long shrunk = 0;
 
 	spin_lock(&cache->c_list_lock);
 	while (nr_to_scan-- && !list_empty(&cache->c_list)) {
 		entry = list_first_entry(&cache->c_list,
 					 struct mb_cache_entry, e_list);
-		if (entry->e_referenced) {
-			entry->e_referenced = 0;
+		/* Drop initial hash reference if there is no user */
+		if (test_bit(MBE_REFERENCED_B, &entry->e_flags) ||
+		    atomic_cmpxchg(&entry->e_refcnt, 1, 0) != 1) {
+			clear_bit(MBE_REFERENCED_B, &entry->e_flags);
 			list_move_tail(&entry->e_list, &cache->c_list);
 			continue;
 		}
 		list_del_init(&entry->e_list);
 		cache->c_entry_count--;
-		/*
-		 * We keep LRU list reference so that entry doesn't go away
-		 * from under us.
-		 */
 		spin_unlock(&cache->c_list_lock);
-		head = mb_cache_entry_head(cache, entry->e_key);
-		hlist_bl_lock(head);
-		if (!hlist_bl_unhashed(&entry->e_hash_list)) {
-			hlist_bl_del_init(&entry->e_hash_list);
-			atomic_dec(&entry->e_refcnt);
-		}
-		hlist_bl_unlock(head);
-		if (mb_cache_entry_put(cache, entry))
-			shrunk++;
+		__mb_cache_entry_free(cache, entry);
+		shrunk++;
 		cond_resched();
 		spin_lock(&cache->c_list_lock);
 	}
@@ -400,11 +450,6 @@
 	 * point.
 	 */
 	list_for_each_entry_safe(entry, next, &cache->c_list, e_list) {
-		if (!hlist_bl_unhashed(&entry->e_hash_list)) {
-			hlist_bl_del_init(&entry->e_hash_list);
-			atomic_dec(&entry->e_refcnt);
-		} else
-			WARN_ON(1);
 		list_del(&entry->e_list);
 		WARN_ON(atomic_read(&entry->e_refcnt) != 1);
 		mb_cache_entry_put(cache, entry);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/minix/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/minix/inode.c
@@ -447,7 +447,8 @@
 	.writepage = minix_writepage,
 	.write_begin = minix_write_begin,
 	.write_end = generic_write_end,
-	.bmap = minix_bmap
+	.bmap = minix_bmap,
+	.direct_IO = noop_direct_IO
 };
 
 static const struct inode_operations minix_symlink_inode_operations = {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/namei.c
@@ -252,6 +252,7 @@
 
 	return result;
 }
+EXPORT_SYMBOL(getname_kernel);
 
 void putname(struct filename *name)
 {
@@ -269,6 +270,7 @@
 	} else
 		__putname(name);
 }
+EXPORT_SYMBOL(putname);
 
 /**
  * check_acl - perform ACL permission checking
@@ -1020,8 +1022,8 @@
 		path_put(&last->link);
 }
 
-int sysctl_protected_symlinks __read_mostly = 0;
-int sysctl_protected_hardlinks __read_mostly = 0;
+int sysctl_protected_symlinks __read_mostly = 1;
+int sysctl_protected_hardlinks __read_mostly = 1;
 int sysctl_protected_fifos __read_mostly;
 int sysctl_protected_regular __read_mostly;
 
@@ -1461,6 +1463,8 @@
 				 * becoming unpinned.
 				 */
 				flags = dentry->d_flags;
+				if (read_seqretry(&mount_lock, nd->m_seq))
+					return false;
 				continue;
 			}
 			if (read_seqretry(&mount_lock, nd->m_seq))
@@ -1537,8 +1541,9 @@
  * when directory is guaranteed to have no in-lookup children
  * at all.
  */
-static struct dentry *__lookup_hash(const struct qstr *name,
-		struct dentry *base, unsigned int flags)
+struct dentry *lookup_one_qstr_excl(const struct qstr *name,
+				    struct dentry *base,
+				    unsigned int flags)
 {
 	struct dentry *dentry = lookup_dcache(name, base, flags);
 	struct dentry *old;
@@ -1562,6 +1567,7 @@
 	}
 	return dentry;
 }
+EXPORT_SYMBOL(lookup_one_qstr_excl);
 
 static struct dentry *lookup_fast(struct nameidata *nd,
 				  struct inode **inode,
@@ -2506,16 +2512,17 @@
 }
 
 /* Note: this does not consume "name" */
-static int filename_parentat(int dfd, struct filename *name,
-			     unsigned int flags, struct path *parent,
-			     struct qstr *last, int *type)
+static int __filename_parentat(int dfd, struct filename *name,
+			       unsigned int flags, struct path *parent,
+			       struct qstr *last, int *type,
+			       const struct path *root)
 {
 	int retval;
 	struct nameidata nd;
 
 	if (IS_ERR(name))
 		return PTR_ERR(name);
-	set_nameidata(&nd, dfd, name, NULL);
+	set_nameidata(&nd, dfd, name, root);
 	retval = path_parentat(&nd, flags | LOOKUP_RCU, parent);
 	if (unlikely(retval == -ECHILD))
 		retval = path_parentat(&nd, flags, parent);
@@ -2530,6 +2537,13 @@
 	return retval;
 }
 
+static int filename_parentat(int dfd, struct filename *name,
+			     unsigned int flags, struct path *parent,
+			     struct qstr *last, int *type)
+{
+	return __filename_parentat(dfd, name, flags, parent, last, type, NULL);
+}
+
 /* does lookup, returns the object with parent locked */
 static struct dentry *__kern_path_locked(struct filename *name, struct path *path)
 {
@@ -2545,7 +2559,7 @@
 		return ERR_PTR(-EINVAL);
 	}
 	inode_lock_nested(path->dentry->d_inode, I_MUTEX_PARENT);
-	d = __lookup_hash(&last, path->dentry, 0);
+	d = lookup_one_qstr_excl(&last, path->dentry, 0);
 	if (IS_ERR(d)) {
 		inode_unlock(path->dentry->d_inode);
 		path_put(path);
@@ -2574,6 +2588,24 @@
 EXPORT_SYMBOL(kern_path);
 
 /**
+ * vfs_path_parent_lookup - lookup a parent path relative to a dentry-vfsmount pair
+ * @filename: filename structure
+ * @flags: lookup flags
+ * @parent: pointer to struct path to fill
+ * @last: last component
+ * @type: type of the last component
+ * @root: pointer to struct path of the base directory
+ */
+int vfs_path_parent_lookup(struct filename *filename, unsigned int flags,
+			   struct path *parent, struct qstr *last, int *type,
+			   const struct path *root)
+{
+	return  __filename_parentat(AT_FDCWD, filename, flags, parent, last,
+				    type, root);
+}
+EXPORT_SYMBOL(vfs_path_parent_lookup);
+
+/**
  * vfs_path_lookup - lookup a file path relative to a dentry-vfsmount pair
  * @dentry:  pointer to dentry of the base directory
  * @mnt: pointer to vfs mount of the base directory
@@ -2718,7 +2750,8 @@
 EXPORT_SYMBOL(lookup_one);
 
 /**
- * lookup_one_len_unlocked - filesystem helper to lookup single pathname component
+ * lookup_one_unlocked - filesystem helper to lookup single pathname component
+ * @mnt_userns:	idmapping of the mount the lookup is performed from
  * @name:	pathname component to lookup
  * @base:	base directory to lookup from
  * @len:	maximum length @len should be interpreted to
@@ -2729,14 +2762,15 @@
  * Unlike lookup_one_len, it should be called without the parent
  * i_mutex held, and will take the i_mutex itself if necessary.
  */
-struct dentry *lookup_one_len_unlocked(const char *name,
-				       struct dentry *base, int len)
+struct dentry *lookup_one_unlocked(struct user_namespace *mnt_userns,
+				   const char *name, struct dentry *base,
+				   int len)
 {
 	struct qstr this;
 	int err;
 	struct dentry *ret;
 
-	err = lookup_one_common(&init_user_ns, name, base, len, &this);
+	err = lookup_one_common(mnt_userns, name, base, len, &this);
 	if (err)
 		return ERR_PTR(err);
 
@@ -2745,6 +2779,59 @@
 		ret = lookup_slow(&this, base, 0);
 	return ret;
 }
+EXPORT_SYMBOL(lookup_one_unlocked);
+
+/**
+ * lookup_one_positive_unlocked - filesystem helper to lookup single
+ *				  pathname component
+ * @mnt_userns:	idmapping of the mount the lookup is performed from
+ * @name:	pathname component to lookup
+ * @base:	base directory to lookup from
+ * @len:	maximum length @len should be interpreted to
+ *
+ * This helper will yield ERR_PTR(-ENOENT) on negatives. The helper returns
+ * known positive or ERR_PTR(). This is what most of the users want.
+ *
+ * Note that pinned negative with unlocked parent _can_ become positive at any
+ * time, so callers of lookup_one_unlocked() need to be very careful; pinned
+ * positives have >d_inode stable, so this one avoids such problems.
+ *
+ * Note that this routine is purely a helper for filesystem usage and should
+ * not be called by generic code.
+ *
+ * The helper should be called without i_mutex held.
+ */
+struct dentry *lookup_one_positive_unlocked(struct user_namespace *mnt_userns,
+					    const char *name,
+					    struct dentry *base, int len)
+{
+	struct dentry *ret = lookup_one_unlocked(mnt_userns, name, base, len);
+
+	if (!IS_ERR(ret) && d_flags_negative(smp_load_acquire(&ret->d_flags))) {
+		dput(ret);
+		ret = ERR_PTR(-ENOENT);
+	}
+	return ret;
+}
+EXPORT_SYMBOL(lookup_one_positive_unlocked);
+
+/**
+ * lookup_one_len_unlocked - filesystem helper to lookup single pathname component
+ * @name:	pathname component to lookup
+ * @base:	base directory to lookup from
+ * @len:	maximum length @len should be interpreted to
+ *
+ * Note that this routine is purely a helper for filesystem usage and should
+ * not be called by generic code.
+ *
+ * Unlike lookup_one_len, it should be called without the parent
+ * i_mutex held, and will take the i_mutex itself if necessary.
+ */
+struct dentry *lookup_one_len_unlocked(const char *name,
+				       struct dentry *base, int len)
+{
+	return lookup_one_unlocked(&init_user_ns, name, base, len);
+}
 EXPORT_SYMBOL(lookup_one_len_unlocked);
 
 /*
@@ -2758,12 +2845,7 @@
 struct dentry *lookup_positive_unlocked(const char *name,
 				       struct dentry *base, int len)
 {
-	struct dentry *ret = lookup_one_len_unlocked(name, base, len);
-	if (!IS_ERR(ret) && d_flags_negative(smp_load_acquire(&ret->d_flags))) {
-		dput(ret);
-		ret = ERR_PTR(-ENOENT);
-	}
-	return ret;
+	return lookup_one_positive_unlocked(&init_user_ns, name, base, len);
 }
 EXPORT_SYMBOL(lookup_positive_unlocked);
 
@@ -2784,7 +2866,7 @@
 	dput(path->dentry);
 	path->dentry = parent;
 	child = d_hash_and_lookup(parent, &this);
-	if (!child)
+	if (IS_ERR_OR_NULL(child))
 		return -ENOENT;
 
 	path->dentry = child;
@@ -2904,39 +2986,79 @@
 	return inode_permission(mnt_userns, dir, MAY_WRITE | MAY_EXEC);
 }
 
+static struct dentry *lock_two_directories(struct dentry *p1, struct dentry *p2)
+{
+	struct dentry *p;
+
+	p = d_ancestor(p2, p1);
+	if (p) {
+		inode_lock_nested(p2->d_inode, I_MUTEX_PARENT);
+		inode_lock_nested(p1->d_inode, I_MUTEX_PARENT2);
+		return p;
+	}
+
+	p = d_ancestor(p1, p2);
+	inode_lock_nested(p1->d_inode, I_MUTEX_PARENT);
+	inode_lock_nested(p2->d_inode, I_MUTEX_PARENT2);
+	return p;
+}
+
 /*
  * p1 and p2 should be directories on the same fs.
  */
 struct dentry *lock_rename(struct dentry *p1, struct dentry *p2)
 {
-	struct dentry *p;
-
 	if (p1 == p2) {
 		inode_lock_nested(p1->d_inode, I_MUTEX_PARENT);
 		return NULL;
 	}
 
 	mutex_lock(&p1->d_sb->s_vfs_rename_mutex);
+	return lock_two_directories(p1, p2);
+}
+EXPORT_SYMBOL(lock_rename);
 
-	p = d_ancestor(p2, p1);
-	if (p) {
+/*
+ * c1 and p2 should be on the same fs.
+ */
+struct dentry *lock_rename_child(struct dentry *c1, struct dentry *p2)
+{
+	if (READ_ONCE(c1->d_parent) == p2) {
+		/*
+		 * hopefully won't need to touch ->s_vfs_rename_mutex at all.
+		 */
 		inode_lock_nested(p2->d_inode, I_MUTEX_PARENT);
-		inode_lock_nested(p1->d_inode, I_MUTEX_CHILD);
-		return p;
-	}
+		/*
+		 * now that p2 is locked, nobody can move in or out of it,
+		 * so the test below is safe.
+		 */
+		if (likely(c1->d_parent == p2))
+			return NULL;
 
-	p = d_ancestor(p1, p2);
-	if (p) {
-		inode_lock_nested(p1->d_inode, I_MUTEX_PARENT);
-		inode_lock_nested(p2->d_inode, I_MUTEX_CHILD);
-		return p;
+		/*
+		 * c1 got moved out of p2 while we'd been taking locks;
+		 * unlock and fall back to slow case.
+		 */
+		inode_unlock(p2->d_inode);
 	}
 
-	inode_lock_nested(p1->d_inode, I_MUTEX_PARENT);
-	inode_lock_nested(p2->d_inode, I_MUTEX_PARENT2);
+	mutex_lock(&c1->d_sb->s_vfs_rename_mutex);
+	/*
+	 * nobody can move out of any directories on this fs.
+	 */
+	if (likely(c1->d_parent != p2))
+		return lock_two_directories(c1->d_parent, p2);
+
+	/*
+	 * c1 got moved into p2 while we were taking locks;
+	 * we need p2 locked and ->s_vfs_rename_mutex unlocked,
+	 * for consistency with lock_rename().
+	 */
+	inode_lock_nested(p2->d_inode, I_MUTEX_PARENT);
+	mutex_unlock(&c1->d_sb->s_vfs_rename_mutex);
 	return NULL;
 }
-EXPORT_SYMBOL(lock_rename);
+EXPORT_SYMBOL(lock_rename_child);
 
 void unlock_rename(struct dentry *p1, struct dentry *p2)
 {
@@ -2949,6 +3071,65 @@
 EXPORT_SYMBOL(unlock_rename);
 
 /**
+ * mode_strip_umask - handle vfs umask stripping
+ * @dir:	parent directory of the new inode
+ * @mode:	mode of the new inode to be created in @dir
+ *
+ * Umask stripping depends on whether or not the filesystem supports POSIX
+ * ACLs. If the filesystem doesn't support it umask stripping is done directly
+ * in here. If the filesystem does support POSIX ACLs umask stripping is
+ * deferred until the filesystem calls posix_acl_create().
+ *
+ * Returns: mode
+ */
+static inline umode_t mode_strip_umask(const struct inode *dir, umode_t mode)
+{
+	if (!IS_POSIXACL(dir))
+		mode &= ~current_umask();
+	return mode;
+}
+
+/**
+ * vfs_prepare_mode - prepare the mode to be used for a new inode
+ * @mnt_userns:		user namespace of the mount the inode was found from
+ * @dir:	parent directory of the new inode
+ * @mode:	mode of the new inode
+ * @mask_perms:	allowed permission by the vfs
+ * @type:	type of file to be created
+ *
+ * This helper consolidates and enforces vfs restrictions on the @mode of a new
+ * object to be created.
+ *
+ * Umask stripping depends on whether the filesystem supports POSIX ACLs (see
+ * the kernel documentation for mode_strip_umask()). Moving umask stripping
+ * after setgid stripping allows the same ordering for both non-POSIX ACL and
+ * POSIX ACL supporting filesystems.
+ *
+ * Note that it's currently valid for @type to be 0 if a directory is created.
+ * Filesystems raise that flag individually and we need to check whether each
+ * filesystem can deal with receiving S_IFDIR from the vfs before we enforce a
+ * non-zero type.
+ *
+ * Returns: mode to be passed to the filesystem
+ */
+static inline umode_t vfs_prepare_mode(struct user_namespace *mnt_userns,
+				       const struct inode *dir, umode_t mode,
+				       umode_t mask_perms, umode_t type)
+{
+	mode = mode_strip_sgid(mnt_userns, dir, mode);
+	mode = mode_strip_umask(dir, mode);
+
+	/*
+	 * Apply the vfs mandated allowed permission mask and set the type of
+	 * file to be created before we call into the filesystem.
+	 */
+	mode &= (mask_perms & ~S_IFMT);
+	mode |= (type & S_IFMT);
+
+	return mode;
+}
+
+/**
  * vfs_create - create new file
  * @mnt_userns:	user namespace of the mount the inode was found from
  * @dir:	inode of @dentry
@@ -2973,8 +3154,8 @@
 
 	if (!dir->i_op->create)
 		return -EACCES;	/* shouldn't it be ENOSYS? */
-	mode &= S_IALLUGO;
-	mode |= S_IFREG;
+
+	mode = vfs_prepare_mode(mnt_userns, dir, mode, S_IALLUGO, S_IFREG);
 	error = security_inode_create(dir, dentry, mode);
 	if (error)
 		return error;
@@ -3239,8 +3420,7 @@
 	if (open_flag & O_CREAT) {
 		if (open_flag & O_EXCL)
 			open_flag &= ~O_TRUNC;
-		if (!IS_POSIXACL(dir->d_inode))
-			mode &= ~current_umask();
+		mode = vfs_prepare_mode(mnt_userns, dir->d_inode, mode, mode, mode);
 		if (likely(got_write))
 			create_error = may_o_create(mnt_userns, &nd->path,
 						    dentry, mode);
@@ -3473,6 +3653,7 @@
 	child = d_alloc(dentry, &slash_name);
 	if (unlikely(!child))
 		goto out_err;
+	mode = vfs_prepare_mode(mnt_userns, dir, mode, mode, mode);
 	error = dir->i_op->tmpfile(mnt_userns, dir, child, mode);
 	if (error)
 		goto out_err;
@@ -3625,18 +3806,14 @@
 {
 	struct dentry *dentry = ERR_PTR(-EEXIST);
 	struct qstr last;
+	bool want_dir = lookup_flags & LOOKUP_DIRECTORY;
+	unsigned int reval_flag = lookup_flags & LOOKUP_REVAL;
+	unsigned int create_flags = LOOKUP_CREATE | LOOKUP_EXCL;
 	int type;
 	int err2;
 	int error;
-	bool is_dir = (lookup_flags & LOOKUP_DIRECTORY);
-
-	/*
-	 * Note that only LOOKUP_REVAL and LOOKUP_DIRECTORY matter here. Any
-	 * other flags passed in are ignored!
-	 */
-	lookup_flags &= LOOKUP_REVAL;
 
-	error = filename_parentat(dfd, name, lookup_flags, path, &last, &type);
+	error = filename_parentat(dfd, name, reval_flag, path, &last, &type);
 	if (error)
 		return ERR_PTR(error);
 
@@ -3650,11 +3827,14 @@
 	/* don't fail immediately if it's r/o, at least try to report other errors */
 	err2 = mnt_want_write(path->mnt);
 	/*
-	 * Do the final lookup.
+	 * Do the final lookup.  Suppress 'create' if there is a trailing
+	 * '/', and a directory wasn't requested.
 	 */
-	lookup_flags |= LOOKUP_CREATE | LOOKUP_EXCL;
+	if (last.name[last.len] && !want_dir)
+		create_flags = 0;
 	inode_lock_nested(path->dentry->d_inode, I_MUTEX_PARENT);
-	dentry = __lookup_hash(&last, path->dentry, lookup_flags);
+	dentry = lookup_one_qstr_excl(&last, path->dentry,
+				      reval_flag | create_flags);
 	if (IS_ERR(dentry))
 		goto unlock;
 
@@ -3668,7 +3848,7 @@
 	 * all is fine. Let's be bastards - you had / on the end, you've
 	 * been asking for (non-existent) directory. -ENOENT for you.
 	 */
-	if (unlikely(!is_dir && last.name[last.len])) {
+	if (unlikely(!create_flags)) {
 		error = -ENOENT;
 		goto fail;
 	}
@@ -3752,6 +3932,7 @@
 	if (!dir->i_op->mknod)
 		return -EPERM;
 
+	mode = vfs_prepare_mode(mnt_userns, dir, mode, mode, mode);
 	error = devcgroup_inode_mknod(mode, dev);
 	if (error)
 		return error;
@@ -3802,9 +3983,8 @@
 	if (IS_ERR(dentry))
 		goto out1;
 
-	if (!IS_POSIXACL(path.dentry->d_inode))
-		mode &= ~current_umask();
-	error = security_path_mknod(&path, dentry, mode, dev);
+	error = security_path_mknod(&path, dentry,
+			mode_strip_umask(path.dentry->d_inode, mode), dev);
 	if (error)
 		goto out2;
 
@@ -3874,7 +4054,7 @@
 	if (!dir->i_op->mkdir)
 		return -EPERM;
 
-	mode &= (S_IRWXUGO|S_ISVTX);
+	mode = vfs_prepare_mode(mnt_userns, dir, mode, S_IRWXUGO | S_ISVTX, 0);
 	error = security_inode_mkdir(dir, dentry, mode);
 	if (error)
 		return error;
@@ -3902,9 +4082,8 @@
 	if (IS_ERR(dentry))
 		goto out_putname;
 
-	if (!IS_POSIXACL(path.dentry->d_inode))
-		mode &= ~current_umask();
-	error = security_path_mkdir(&path, dentry, mode);
+	error = security_path_mkdir(&path, dentry,
+			mode_strip_umask(path.dentry->d_inode, mode));
 	if (!error) {
 		struct user_namespace *mnt_userns;
 		mnt_userns = mnt_user_ns(path.mnt);
@@ -3975,13 +4154,12 @@
 	dentry->d_inode->i_flags |= S_DEAD;
 	dont_mount(dentry);
 	detach_mounts(dentry);
-	fsnotify_rmdir(dir, dentry);
 
 out:
 	inode_unlock(dentry->d_inode);
 	dput(dentry);
 	if (!error)
-		d_delete(dentry);
+		d_delete_notify(dir, dentry);
 	return error;
 }
 EXPORT_SYMBOL(vfs_rmdir);
@@ -4017,7 +4195,7 @@
 		goto exit2;
 
 	inode_lock_nested(path.dentry->d_inode, I_MUTEX_PARENT);
-	dentry = __lookup_hash(&last, path.dentry, lookup_flags);
+	dentry = lookup_one_qstr_excl(&last, path.dentry, lookup_flags);
 	error = PTR_ERR(dentry);
 	if (IS_ERR(dentry))
 		goto exit3;
@@ -4103,7 +4281,6 @@
 			if (!error) {
 				dont_mount(dentry);
 				detach_mounts(dentry);
-				fsnotify_unlink(dir, dentry);
 			}
 		}
 	}
@@ -4111,9 +4288,11 @@
 	inode_unlock(target);
 
 	/* We don't d_delete() NFS sillyrenamed files--they still exist. */
-	if (!error && !(dentry->d_flags & DCACHE_NFSFS_RENAMED)) {
+	if (!error && dentry->d_flags & DCACHE_NFSFS_RENAMED) {
+		fsnotify_unlink(dir, dentry);
+	} else if (!error) {
 		fsnotify_link_count(target);
-		d_delete(dentry);
+		d_delete_notify(dir, dentry);
 	}
 
 	return error;
@@ -4150,7 +4329,7 @@
 		goto exit2;
 retry_deleg:
 	inode_lock_nested(path.dentry->d_inode, I_MUTEX_PARENT);
-	dentry = __lookup_hash(&last, path.dentry, lookup_flags);
+	dentry = lookup_one_qstr_excl(&last, path.dentry, lookup_flags);
 	error = PTR_ERR(dentry);
 	if (!IS_ERR(dentry)) {
 		struct user_namespace *mnt_userns;
@@ -4506,11 +4685,12 @@
  *
  *	a) we can get into loop creation.
  *	b) race potential - two innocent renames can create a loop together.
- *	   That's where 4.4 screws up. Current fix: serialization on
+ *	   That's where 4.4BSD screws up. Current fix: serialization on
  *	   sb->s_vfs_rename_mutex. We might be more accurate, but that's another
  *	   story.
- *	c) we have to lock _four_ objects - parents and victim (if it exists),
- *	   and source (if it is not a directory).
+ *	c) we may have to lock up to _four_ objects - parents and victim (if it exists),
+ *	   and source (if it's a non-directory or a subdirectory that moves to
+ *	   different parent).
  *	   And that - after we got ->i_mutex on parents (until then we don't know
  *	   whether the target exists).  Solution: try to be smart with locking
  *	   order for inodes.  We rely on the fact that tree topology may change
@@ -4542,6 +4722,7 @@
 	bool new_is_dir = false;
 	unsigned max_links = new_dir->i_sb->s_max_links;
 	struct name_snapshot old_name;
+	bool lock_old_subdir, lock_new_subdir;
 
 	if (source == target)
 		return 0;
@@ -4594,10 +4775,33 @@
 
 	take_dentry_name_snapshot(&old_name, old_dentry);
 	dget(new_dentry);
-	if (!is_dir || (flags & RENAME_EXCHANGE))
+	/*
+	 * Lock children.
+	 * The source subdirectory needs to be locked on cross-directory
+	 * rename or cross-directory exchange since its parent changes.
+	 * The target subdirectory needs to be locked on cross-directory
+	 * exchange due to parent change and on any rename due to becoming
+	 * a victim.
+	 * Non-directories need locking in all cases (for NFS reasons);
+	 * they get locked after any subdirectories (in inode address order).
+	 *
+	 * NOTE: WE ONLY LOCK UNRELATED DIRECTORIES IN CROSS-DIRECTORY CASE.
+	 * NEVER, EVER DO THAT WITHOUT ->s_vfs_rename_mutex.
+	 */
+	lock_old_subdir = new_dir != old_dir;
+	lock_new_subdir = new_dir != old_dir || !(flags & RENAME_EXCHANGE);
+	if (is_dir) {
+		if (lock_old_subdir)
+			inode_lock_nested(source, I_MUTEX_CHILD);
+		if (target && (!new_is_dir || lock_new_subdir))
+			inode_lock(target);
+	} else if (new_is_dir) {
+		if (lock_new_subdir)
+			inode_lock_nested(target, I_MUTEX_CHILD);
+		inode_lock(source);
+	} else {
 		lock_two_nondirectories(source, target);
-	else if (target)
-		inode_lock(target);
+	}
 
 	error = -EPERM;
 	if (IS_SWAPFILE(source) || (target && IS_SWAPFILE(target)))
@@ -4645,9 +4849,9 @@
 			d_exchange(old_dentry, new_dentry);
 	}
 out:
-	if (!is_dir || (flags & RENAME_EXCHANGE))
-		unlock_two_nondirectories(source, target);
-	else if (target)
+	if (!is_dir || lock_old_subdir)
+		inode_unlock(source);
+	if (target && (!new_is_dir || lock_new_subdir))
 		inode_unlock(target);
 	dput(new_dentry);
 	if (!error) {
@@ -4719,7 +4923,8 @@
 retry_deleg:
 	trap = lock_rename(new_path.dentry, old_path.dentry);
 
-	old_dentry = __lookup_hash(&old_last, old_path.dentry, lookup_flags);
+	old_dentry = lookup_one_qstr_excl(&old_last, old_path.dentry,
+					  lookup_flags);
 	error = PTR_ERR(old_dentry);
 	if (IS_ERR(old_dentry))
 		goto exit3;
@@ -4727,7 +4932,8 @@
 	error = -ENOENT;
 	if (d_is_negative(old_dentry))
 		goto exit4;
-	new_dentry = __lookup_hash(&new_last, new_path.dentry, lookup_flags | target_flags);
+	new_dentry = lookup_one_qstr_excl(&new_last, new_path.dentry,
+					  lookup_flags | target_flags);
 	error = PTR_ERR(new_dentry);
 	if (IS_ERR(new_dentry))
 		goto exit4;
@@ -4908,10 +5114,9 @@
 EXPORT_SYMBOL(vfs_get_link);
 
 /* get the link contents into pagecache */
-const char *page_get_link(struct dentry *dentry, struct inode *inode,
-			  struct delayed_call *callback)
+static char *__page_get_link(struct dentry *dentry, struct inode *inode,
+			     struct delayed_call *callback)
 {
-	char *kaddr;
 	struct page *page;
 	struct address_space *mapping = inode->i_mapping;
 
@@ -4930,8 +5135,23 @@
 	}
 	set_delayed_call(callback, page_put_link, page);
 	BUG_ON(mapping_gfp_mask(mapping) & __GFP_HIGHMEM);
-	kaddr = page_address(page);
-	nd_terminate_link(kaddr, inode->i_size, PAGE_SIZE - 1);
+	return page_address(page);
+}
+
+const char *page_get_link_raw(struct dentry *dentry, struct inode *inode,
+			      struct delayed_call *callback)
+{
+	return __page_get_link(dentry, inode, callback);
+}
+EXPORT_SYMBOL_GPL(page_get_link_raw);
+
+const char *page_get_link(struct dentry *dentry, struct inode *inode,
+					struct delayed_call *callback)
+{
+	char *kaddr = __page_get_link(dentry, inode, callback);
+
+	if (!IS_ERR(kaddr))
+		nd_terminate_link(kaddr, inode->i_size, PAGE_SIZE - 1);
 	return kaddr;
 }
 
@@ -4961,7 +5181,7 @@
 {
 	struct address_space *mapping = inode->i_mapping;
 	struct page *page;
-	void *fsdata;
+	void *fsdata = NULL;
 	int err;
 	unsigned int flags = 0;
 	if (nofs)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/namespace.c
+++ linux-xilinx-zynqmp-5.15.0/fs/namespace.c
@@ -31,6 +31,7 @@
 #include <uapi/linux/mount.h>
 #include <linux/fs_context.h>
 #include <linux/shmem_fs.h>
+#include <linux/mnt_idmapping.h>
 
 #include "pnode.h"
 #include "internal.h"
@@ -439,6 +440,7 @@
 	mnt_dec_writers(real_mount(mnt));
 	preempt_enable();
 }
+EXPORT_SYMBOL_GPL(__mnt_drop_write);
 
 /**
  * mnt_drop_write - give up write access to a mount
@@ -561,7 +563,7 @@
 	struct user_namespace *mnt_userns;
 
 	mnt_userns = mnt_user_ns(&mnt->mnt);
-	if (mnt_userns != &init_user_ns)
+	if (!initial_idmapping(mnt_userns))
 		put_user_ns(mnt_userns);
 	kfree_const(mnt->mnt_devname);
 #ifdef CONFIG_SMP
@@ -808,6 +810,13 @@
 	return mnt->mnt_ns == current->nsproxy->mnt_ns;
 }
 
+/* for aufs, CONFIG_AUFS_BR_FUSE */
+int is_current_mnt_ns(struct vfsmount *mnt)
+{
+	return check_mnt(real_mount(mnt));
+}
+EXPORT_SYMBOL_GPL(is_current_mnt_ns);
+
 /*
  * vfsmount lock must be held for write
  */
@@ -965,6 +974,7 @@
 struct vfsmount *vfs_create_mount(struct fs_context *fc)
 {
 	struct mount *mnt;
+	struct user_namespace *fs_userns;
 
 	if (!fc->root)
 		return ERR_PTR(-EINVAL);
@@ -982,6 +992,10 @@
 	mnt->mnt_mountpoint	= mnt->mnt.mnt_root;
 	mnt->mnt_parent		= mnt;
 
+	fs_userns = mnt->mnt.mnt_sb->s_user_ns;
+	if (!initial_idmapping(fs_userns))
+		mnt->mnt.mnt_userns = get_user_ns(fs_userns);
+
 	lock_mount_hash();
 	list_add_tail(&mnt->mnt_instance, &mnt->mnt.mnt_sb->s_mounts);
 	unlock_mount_hash();
@@ -1072,7 +1086,7 @@
 
 	atomic_inc(&sb->s_active);
 	mnt->mnt.mnt_userns = mnt_user_ns(&old->mnt);
-	if (mnt->mnt.mnt_userns != &init_user_ns)
+	if (!initial_idmapping(mnt->mnt.mnt_userns))
 		mnt->mnt.mnt_userns = get_user_ns(mnt->mnt.mnt_userns);
 	mnt->mnt.mnt_sb = sb;
 	mnt->mnt.mnt_root = dget(root);
@@ -2005,6 +2019,7 @@
 	}
 	return 0;
 }
+EXPORT_SYMBOL_GPL(iterate_mounts);
 
 static void lock_mnt_tree(struct mount *mnt)
 {
@@ -2561,20 +2576,27 @@
 	struct super_block *sb = mnt->mnt_sb;
 
 	if (!__mnt_is_readonly(mnt) &&
+	   (!(sb->s_iflags & SB_I_TS_EXPIRY_WARNED)) &&
 	   (ktime_get_real_seconds() + TIME_UPTIME_SEC_MAX > sb->s_time_max)) {
-		char *buf = (char *)__get_free_page(GFP_KERNEL);
-		char *mntpath = buf ? d_path(mountpoint, buf, PAGE_SIZE) : ERR_PTR(-ENOMEM);
-		struct tm tm;
+		char *buf, *mntpath;
 
-		time64_to_tm(sb->s_time_max, 0, &tm);
+		buf = (char *)__get_free_page(GFP_KERNEL);
+		if (buf)
+			mntpath = d_path(mountpoint, buf, PAGE_SIZE);
+		else
+			mntpath = ERR_PTR(-ENOMEM);
+		if (IS_ERR(mntpath))
+			mntpath = "(unknown)";
 
-		pr_warn("%s filesystem being %s at %s supports timestamps until %04ld (0x%llx)\n",
+		pr_warn("%s filesystem being %s at %s supports timestamps until %ptTd (0x%llx)\n",
 			sb->s_type->name,
 			is_mounted(mnt) ? "remounted" : "mounted",
-			mntpath,
-			tm.tm_year+1900, (unsigned long long)sb->s_time_max);
+			mntpath, &sb->s_time_max,
+			(unsigned long long)sb->s_time_max);
 
-		free_page((unsigned long)buf);
+		sb->s_iflags |= SB_I_TS_EXPIRY_WARNED;
+		if (buf)
+			free_page((unsigned long)buf);
 	}
 }
 
@@ -2641,7 +2663,12 @@
 	if (IS_ERR(fc))
 		return PTR_ERR(fc);
 
+	/*
+	 * Indicate to the filesystem that the remount request is coming
+	 * from the legacy mount system call.
+	 */
 	fc->oldapi = true;
+
 	err = parse_monolithic_mount_data(fc, data);
 	if (!err) {
 		down_write(&sb->s_umount);
@@ -2975,6 +3002,12 @@
 	if (IS_ERR(fc))
 		return PTR_ERR(fc);
 
+	/*
+	 * Indicate to the filesystem that the mount request is coming
+	 * from the legacy mount system call.
+	 */
+	fc->oldapi = true;
+
 	if (subtype)
 		err = vfs_parse_fs_string(fc, "subtype",
 					  subtype, strlen(subtype));
@@ -3927,28 +3960,32 @@
 static int can_idmap_mount(const struct mount_kattr *kattr, struct mount *mnt)
 {
 	struct vfsmount *m = &mnt->mnt;
+	struct user_namespace *fs_userns = m->mnt_sb->s_user_ns;
 
 	if (!kattr->mnt_userns)
 		return 0;
 
 	/*
+	 * Creating an idmapped mount with the filesystem wide idmapping
+	 * doesn't make sense so block that. We don't allow mushy semantics.
+	 */
+	if (kattr->mnt_userns == fs_userns)
+		return -EINVAL;
+
+	/*
 	 * Once a mount has been idmapped we don't allow it to change its
 	 * mapping. It makes things simpler and callers can just create
 	 * another bind-mount they can idmap if they want to.
 	 */
-	if (mnt_user_ns(m) != &init_user_ns)
+	if (is_idmapped_mnt(m))
 		return -EPERM;
 
 	/* The underlying filesystem doesn't support idmapped mounts yet. */
 	if (!(m->mnt_sb->s_type->fs_flags & FS_ALLOW_IDMAP))
 		return -EINVAL;
 
-	/* Don't yet support filesystem mountable in user namespaces. */
-	if (m->mnt_sb->s_user_ns != &init_user_ns)
-		return -EINVAL;
-
 	/* We're not controlling the superblock. */
-	if (!capable(CAP_SYS_ADMIN))
+	if (!ns_capable(fs_userns, CAP_SYS_ADMIN))
 		return -EPERM;
 
 	/* Mount has already been visible in the filesystem hierarchy. */
@@ -3958,6 +3995,23 @@
 	return 0;
 }
 
+/**
+ * mnt_allow_writers() - check whether the attribute change allows writers
+ * @kattr: the new mount attributes
+ * @mnt: the mount to which @kattr will be applied
+ *
+ * Check whether thew new mount attributes in @kattr allow concurrent writers.
+ *
+ * Return: true if writers need to be held, false if not
+ */
+static inline bool mnt_allow_writers(const struct mount_kattr *kattr,
+				     const struct mount *mnt)
+{
+	return (!(kattr->attr_set & MNT_READONLY) ||
+		(mnt->mnt.mnt_flags & MNT_READONLY)) &&
+	       !kattr->mnt_userns;
+}
+
 static struct mount *mount_setattr_prepare(struct mount_kattr *kattr,
 					   struct mount *mnt, int *err)
 {
@@ -3988,8 +4042,7 @@
 
 		last = m;
 
-		if ((kattr->attr_set & MNT_READONLY) &&
-		    !(m->mnt.mnt_flags & MNT_READONLY)) {
+		if (!mnt_allow_writers(kattr, m)) {
 			*err = mnt_hold_writers(m);
 			if (*err)
 				goto out;
@@ -4002,14 +4055,27 @@
 
 static void do_idmap_mount(const struct mount_kattr *kattr, struct mount *mnt)
 {
-	struct user_namespace *mnt_userns;
+	struct user_namespace *mnt_userns, *old_mnt_userns;
 
 	if (!kattr->mnt_userns)
 		return;
 
+	/*
+	 * We're the only ones able to change the mount's idmapping. So
+	 * mnt->mnt.mnt_userns is stable and we can retrieve it directly.
+	 */
+	old_mnt_userns = mnt->mnt.mnt_userns;
+
 	mnt_userns = get_user_ns(kattr->mnt_userns);
 	/* Pairs with smp_load_acquire() in mnt_user_ns(). */
 	smp_store_release(&mnt->mnt.mnt_userns, mnt_userns);
+
+	/*
+	 * If this is an idmapped filesystem drop the reference we've taken
+	 * in vfs_create_mount() before.
+	 */
+	if (!initial_idmapping(old_mnt_userns))
+		put_user_ns(old_mnt_userns);
 }
 
 static void mount_setattr_commit(struct mount_kattr *kattr,
@@ -4027,13 +4093,8 @@
 			WRITE_ONCE(m->mnt.mnt_flags, flags);
 		}
 
-		/*
-		 * We either set MNT_READONLY above so make it visible
-		 * before ~MNT_WRITE_HOLD or we failed to recursively
-		 * apply mount options.
-		 */
-		if ((kattr->attr_set & MNT_READONLY) &&
-		    (m->mnt.mnt_flags & MNT_WRITE_HOLD))
+		/* If we had to hold writers unblock them. */
+		if (m->mnt.mnt_flags & MNT_WRITE_HOLD)
 			mnt_unhold_writers(m);
 
 		if (!err && kattr->propagation)
@@ -4087,9 +4148,9 @@
 	unlock_mount_hash();
 
 	if (kattr->propagation) {
-		namespace_unlock();
 		if (err)
 			cleanup_group_ids(mnt, NULL);
+		namespace_unlock();
 	}
 
 	return err;
@@ -4133,16 +4194,25 @@
 	}
 
 	/*
-	 * The init_user_ns is used to indicate that a vfsmount is not idmapped.
-	 * This is simpler than just having to treat NULL as unmapped. Users
-	 * wanting to idmap a mount to init_user_ns can just use a namespace
-	 * with an identity mapping.
+	 * The initial idmapping cannot be used to create an idmapped
+	 * mount. We use the initial idmapping as an indicator of a mount
+	 * that is not idmapped. It can simply be passed into helpers that
+	 * are aware of idmapped mounts as a convenient shortcut. A user
+	 * can just create a dedicated identity mapping to achieve the same
+	 * result.
 	 */
 	mnt_userns = container_of(ns, struct user_namespace, ns);
-	if (mnt_userns == &init_user_ns) {
+	if (initial_idmapping(mnt_userns)) {
+		err = -EPERM;
+		goto out_fput;
+	}
+
+	/* We're not controlling the target namespace. */
+	if (!ns_capable(mnt_userns, CAP_SYS_ADMIN)) {
 		err = -EPERM;
 		goto out_fput;
 	}
+
 	kattr->mnt_userns = get_user_ns(mnt_userns);
 
 out_fput:
@@ -4263,12 +4333,11 @@
 		return err;
 
 	err = user_path_at(dfd, path, kattr.lookup_flags, &target);
-	if (err)
-		return err;
-
-	err = do_mount_setattr(&target, &kattr);
+	if (!err) {
+		err = do_mount_setattr(&target, &kattr);
+		path_put(&target);
+	}
 	finish_mount_kattr(&kattr);
-	path_put(&target);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/netfs/read_helper.c
+++ linux-xilinx-zynqmp-5.15.0/fs/netfs/read_helper.c
@@ -354,16 +354,11 @@
 	netfs_rreq_do_write_to_cache(rreq);
 }
 
-static void netfs_rreq_write_to_cache(struct netfs_read_request *rreq,
-				      bool was_async)
+static void netfs_rreq_write_to_cache(struct netfs_read_request *rreq)
 {
-	if (was_async) {
-		rreq->work.func = netfs_rreq_write_to_cache_work;
-		if (!queue_work(system_unbound_wq, &rreq->work))
-			BUG();
-	} else {
-		netfs_rreq_do_write_to_cache(rreq);
-	}
+	rreq->work.func = netfs_rreq_write_to_cache_work;
+	if (!queue_work(system_unbound_wq, &rreq->work))
+		BUG();
 }
 
 /*
@@ -560,7 +555,7 @@
 	wake_up_bit(&rreq->flags, NETFS_RREQ_IN_PROGRESS);
 
 	if (test_bit(NETFS_RREQ_WRITE_TO_CACHE, &rreq->flags))
-		return netfs_rreq_write_to_cache(rreq, was_async);
+		return netfs_rreq_write_to_cache(rreq);
 
 	netfs_rreq_completed(rreq, was_async);
 }
@@ -963,7 +958,7 @@
 	rreq = netfs_alloc_read_request(ops, netfs_priv, file);
 	if (!rreq) {
 		if (netfs_priv)
-			ops->cleanup(netfs_priv, page_file_mapping(page));
+			ops->cleanup(page_file_mapping(page), netfs_priv);
 		unlock_page(page);
 		return -ENOMEM;
 	}
@@ -1190,7 +1185,7 @@
 		goto error;
 have_page_no_wait:
 	if (netfs_priv)
-		ops->cleanup(netfs_priv, mapping);
+		ops->cleanup(mapping, netfs_priv);
 	*_page = page;
 	_leave(" = 0");
 	return 0;
@@ -1201,7 +1196,7 @@
 	unlock_page(page);
 	put_page(page);
 	if (netfs_priv)
-		ops->cleanup(netfs_priv, mapping);
+		ops->cleanup(mapping, netfs_priv);
 	_leave(" = %d", ret);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/blocklayout/blocklayout.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/blocklayout/blocklayout.c
@@ -599,6 +599,8 @@
 		nfs4_delete_deviceid(node->ld, node->nfs_client, id);
 		goto retry;
 	}
+
+	nfs4_put_deviceid_node(node);
 	return ERR_PTR(-ENODEV);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/blocklayout/dev.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/blocklayout/dev.c
@@ -422,7 +422,7 @@
 	int ret, i;
 
 	d->children = kcalloc(v->concat.volumes_count,
-			sizeof(struct pnfs_block_dev), GFP_KERNEL);
+			sizeof(struct pnfs_block_dev), gfp_mask);
 	if (!d->children)
 		return -ENOMEM;
 
@@ -451,7 +451,7 @@
 	int ret, i;
 
 	d->children = kcalloc(v->stripe.volumes_count,
-			sizeof(struct pnfs_block_dev), GFP_KERNEL);
+			sizeof(struct pnfs_block_dev), gfp_mask);
 	if (!d->children)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/callback.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/callback.c
@@ -17,7 +17,6 @@
 #include <linux/errno.h>
 #include <linux/mutex.h>
 #include <linux/freezer.h>
-#include <linux/kthread.h>
 #include <linux/sunrpc/svcauth_gss.h>
 #include <linux/sunrpc/bc_xprt.h>
 
@@ -45,18 +44,18 @@
 	int ret;
 	struct nfs_net *nn = net_generic(net, nfs_net_id);
 
-	ret = svc_create_xprt(serv, "tcp", net, PF_INET,
-				nfs_callback_set_tcpport, SVC_SOCK_ANONYMOUS,
-				cred);
+	ret = svc_xprt_create(serv, "tcp", net, PF_INET,
+			      nfs_callback_set_tcpport, SVC_SOCK_ANONYMOUS,
+			      cred);
 	if (ret <= 0)
 		goto out_err;
 	nn->nfs_callback_tcpport = ret;
 	dprintk("NFS: Callback listener port = %u (af %u, net %x)\n",
 		nn->nfs_callback_tcpport, PF_INET, net->ns.inum);
 
-	ret = svc_create_xprt(serv, "tcp", net, PF_INET6,
-				nfs_callback_set_tcpport, SVC_SOCK_ANONYMOUS,
-				cred);
+	ret = svc_xprt_create(serv, "tcp", net, PF_INET6,
+			      nfs_callback_set_tcpport, SVC_SOCK_ANONYMOUS,
+			      cred);
 	if (ret > 0) {
 		nn->nfs_callback_tcpport6 = ret;
 		dprintk("NFS: Callback listener port = %u (af %u, net %x)\n",
@@ -81,9 +80,6 @@
 	set_freezable();
 
 	while (!kthread_freezable_should_stop(NULL)) {
-
-		if (signal_pending(current))
-			flush_signals(current);
 		/*
 		 * Listen for a request on the socket
 		 */
@@ -92,8 +88,8 @@
 			continue;
 		svc_process(rqstp);
 	}
+
 	svc_exit_thread(rqstp);
-	module_put_and_exit(0);
 	return 0;
 }
 
@@ -113,11 +109,7 @@
 	set_freezable();
 
 	while (!kthread_freezable_should_stop(NULL)) {
-
-		if (signal_pending(current))
-			flush_signals(current);
-
-		prepare_to_wait(&serv->sv_cb_waitq, &wq, TASK_INTERRUPTIBLE);
+		prepare_to_wait(&serv->sv_cb_waitq, &wq, TASK_IDLE);
 		spin_lock_bh(&serv->sv_cb_lock);
 		if (!list_empty(&serv->sv_cb_list)) {
 			req = list_first_entry(&serv->sv_cb_list,
@@ -132,12 +124,12 @@
 		} else {
 			spin_unlock_bh(&serv->sv_cb_lock);
 			if (!kthread_should_stop())
-				schedule();
+				freezable_schedule();
 			finish_wait(&serv->sv_cb_waitq, &wq);
 		}
 	}
+
 	svc_exit_thread(rqstp);
-	module_put_and_exit(0);
 	return 0;
 }
 
@@ -169,12 +161,12 @@
 	if (nrservs < NFS4_MIN_NR_CALLBACK_THREADS)
 		nrservs = NFS4_MIN_NR_CALLBACK_THREADS;
 
-	if (serv->sv_nrthreads-1 == nrservs)
+	if (serv->sv_nrthreads == nrservs)
 		return 0;
 
-	ret = serv->sv_ops->svo_setup(serv, NULL, nrservs);
+	ret = svc_set_num_threads(serv, NULL, nrservs);
 	if (ret) {
-		serv->sv_ops->svo_setup(serv, NULL, 0);
+		svc_set_num_threads(serv, NULL, 0);
 		return ret;
 	}
 	dprintk("nfs_callback_up: service started\n");
@@ -189,7 +181,7 @@
 		return;
 
 	dprintk("NFS: destroy per-net callback data; net=%x\n", net->ns.inum);
-	svc_shutdown_net(serv, net);
+	svc_xprt_destroy_all(serv, net);
 }
 
 static int nfs_callback_up_net(int minorversion, struct svc_serv *serv,
@@ -232,59 +224,17 @@
 	return ret;
 }
 
-static const struct svc_serv_ops nfs40_cb_sv_ops = {
-	.svo_function		= nfs4_callback_svc,
-	.svo_enqueue_xprt	= svc_xprt_do_enqueue,
-	.svo_setup		= svc_set_num_threads_sync,
-	.svo_module		= THIS_MODULE,
-};
-#if defined(CONFIG_NFS_V4_1)
-static const struct svc_serv_ops nfs41_cb_sv_ops = {
-	.svo_function		= nfs41_callback_svc,
-	.svo_enqueue_xprt	= svc_xprt_do_enqueue,
-	.svo_setup		= svc_set_num_threads_sync,
-	.svo_module		= THIS_MODULE,
-};
-
-static const struct svc_serv_ops *nfs4_cb_sv_ops[] = {
-	[0] = &nfs40_cb_sv_ops,
-	[1] = &nfs41_cb_sv_ops,
-};
-#else
-static const struct svc_serv_ops *nfs4_cb_sv_ops[] = {
-	[0] = &nfs40_cb_sv_ops,
-	[1] = NULL,
-};
-#endif
-
 static struct svc_serv *nfs_callback_create_svc(int minorversion)
 {
 	struct nfs_callback_data *cb_info = &nfs_callback_info[minorversion];
-	const struct svc_serv_ops *sv_ops;
+	int (*threadfn)(void *data);
 	struct svc_serv *serv;
 
 	/*
 	 * Check whether we're already up and running.
 	 */
-	if (cb_info->serv) {
-		/*
-		 * Note: increase service usage, because later in case of error
-		 * svc_destroy() will be called.
-		 */
-		svc_get(cb_info->serv);
-		return cb_info->serv;
-	}
-
-	switch (minorversion) {
-	case 0:
-		sv_ops = nfs4_cb_sv_ops[0];
-		break;
-	default:
-		sv_ops = nfs4_cb_sv_ops[1];
-	}
-
-	if (sv_ops == NULL)
-		return ERR_PTR(-ENOTSUPP);
+	if (cb_info->serv)
+		return svc_get(cb_info->serv);
 
 	/*
 	 * Sanity check: if there's no task,
@@ -294,7 +244,16 @@
 		printk(KERN_WARNING "nfs_callback_create_svc: no kthread, %d users??\n",
 			cb_info->users);
 
-	serv = svc_create_pooled(&nfs4_callback_program, NFS4_CALLBACK_BUFSIZE, sv_ops);
+	threadfn = nfs4_callback_svc;
+#if defined(CONFIG_NFS_V4_1)
+	if (minorversion)
+		threadfn = nfs41_callback_svc;
+#else
+	if (minorversion)
+		return ERR_PTR(-ENOTSUPP);
+#endif
+	serv = svc_create(&nfs4_callback_program, NFS4_CALLBACK_BUFSIZE,
+			  threadfn);
 	if (!serv) {
 		printk(KERN_ERR "nfs_callback_create_svc: create service failed\n");
 		return ERR_PTR(-ENOMEM);
@@ -335,16 +294,10 @@
 		goto err_start;
 
 	cb_info->users++;
-	/*
-	 * svc_create creates the svc_serv with sv_nrthreads == 1, and then
-	 * svc_prepare_thread increments that. So we need to call svc_destroy
-	 * on both success and failure so that the refcount is 1 when the
-	 * thread exits.
-	 */
 err_net:
 	if (!cb_info->users)
 		cb_info->serv = NULL;
-	svc_destroy(serv);
+	svc_put(serv);
 err_create:
 	mutex_unlock(&nfs_callback_mutex);
 	return ret;
@@ -369,8 +322,8 @@
 	cb_info->users--;
 	if (cb_info->users == 0) {
 		svc_get(serv);
-		serv->sv_ops->svo_setup(serv, NULL, 0);
-		svc_destroy(serv);
+		svc_set_num_threads(serv, NULL, 0);
+		svc_put(serv);
 		dprintk("nfs_callback_down: service destroyed\n");
 		cb_info->serv = NULL;
 	}
@@ -454,15 +407,12 @@
 	[4] = &nfs4_callback_version4,
 };
 
-static struct svc_stat nfs4_callback_stats;
-
 static struct svc_program nfs4_callback_program = {
 	.pg_prog = NFS4_CALLBACK,			/* RPC service number */
 	.pg_nvers = ARRAY_SIZE(nfs4_callback_version),	/* Number of entries */
 	.pg_vers = nfs4_callback_version,		/* version table */
 	.pg_name = "NFSv4 callback",			/* service name */
 	.pg_class = "nfs",				/* authentication class */
-	.pg_stats = &nfs4_callback_stats,
 	.pg_authenticate = nfs_callback_authenticate,
 	.pg_init_request = svc_generic_init_request,
 	.pg_rpcbind_set	= svc_generic_rpcbind_set,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/callback.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/callback.h
@@ -170,7 +170,7 @@
 };
 
 struct cb_devicenotifyargs {
-	int				 ndevs;
+	uint32_t			 ndevs;
 	struct cb_devicenotifyitem	 *devs;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/callback_proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/callback_proc.c
@@ -288,6 +288,7 @@
 		rv = NFS4_OK;
 		break;
 	case -ENOENT:
+		set_bit(NFS_LAYOUT_DRAIN, &lo->plh_flags);
 		/* Embrace your forgetfulness! */
 		rv = NFS4ERR_NOMATCHING_LAYOUT;
 
@@ -358,12 +359,11 @@
 				  struct cb_process_state *cps)
 {
 	struct cb_devicenotifyargs *args = argp;
-	int i;
+	const struct pnfs_layoutdriver_type *ld = NULL;
+	uint32_t i;
 	__be32 res = 0;
-	struct nfs_client *clp = cps->clp;
-	struct nfs_server *server = NULL;
 
-	if (!clp) {
+	if (!cps->clp) {
 		res = cpu_to_be32(NFS4ERR_OP_NOT_IN_SESSION);
 		goto out;
 	}
@@ -371,23 +371,15 @@
 	for (i = 0; i < args->ndevs; i++) {
 		struct cb_devicenotifyitem *dev = &args->devs[i];
 
-		if (!server ||
-		    server->pnfs_curr_ld->id != dev->cbd_layout_type) {
-			rcu_read_lock();
-			list_for_each_entry_rcu(server, &clp->cl_superblocks, client_link)
-				if (server->pnfs_curr_ld &&
-				    server->pnfs_curr_ld->id == dev->cbd_layout_type) {
-					rcu_read_unlock();
-					goto found;
-				}
-			rcu_read_unlock();
-			continue;
+		if (!ld || ld->id != dev->cbd_layout_type) {
+			pnfs_put_layoutdriver(ld);
+			ld = pnfs_find_layoutdriver(dev->cbd_layout_type);
+			if (!ld)
+				continue;
 		}
-
-	found:
-		nfs4_delete_deviceid(server->pnfs_curr_ld, clp, &dev->cbd_dev_id);
+		nfs4_delete_deviceid(ld, cps->clp, &dev->cbd_dev_id);
 	}
-
+	pnfs_put_layoutdriver(ld);
 out:
 	kfree(args->devs);
 	return res;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/callback_xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/callback_xdr.c
@@ -67,9 +67,9 @@
  * svc_process_common() looks for an XDR encoder to know when
  * not to drop a Reply.
  */
-static int nfs4_encode_void(struct svc_rqst *rqstp, __be32 *p)
+static bool nfs4_encode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return xdr_ressize_check(rqstp, p);
+	return true;
 }
 
 static __be32 decode_string(struct xdr_stream *xdr, unsigned int *len,
@@ -258,11 +258,9 @@
 				void *argp)
 {
 	struct cb_devicenotifyargs *args = argp;
+	uint32_t tmp, n, i;
 	__be32 *p;
 	__be32 status = 0;
-	u32 tmp;
-	int n, i;
-	args->ndevs = 0;
 
 	/* Num of device notifications */
 	p = xdr_inline_decode(xdr, sizeof(uint32_t));
@@ -271,12 +269,8 @@
 		goto out;
 	}
 	n = ntohl(*p++);
-	if (n <= 0)
-		goto out;
-	if (n > ULONG_MAX / sizeof(*args->devs)) {
-		status = htonl(NFS4ERR_BADXDR);
+	if (n == 0)
 		goto out;
-	}
 
 	args->devs = kmalloc_array(n, sizeof(*args->devs), GFP_KERNEL);
 	if (!args->devs) {
@@ -330,19 +324,21 @@
 			dev->cbd_immediate = 0;
 		}
 
-		args->ndevs++;
-
 		dprintk("%s: type %d layout 0x%x immediate %d\n",
 			__func__, dev->cbd_notify_type, dev->cbd_layout_type,
 			dev->cbd_immediate);
 	}
+	args->ndevs = n;
+	dprintk("%s: ndevs %d\n", __func__, args->ndevs);
+	return 0;
+err:
+	kfree(args->devs);
 out:
+	args->devs = NULL;
+	args->ndevs = 0;
 	dprintk("%s: status %d ndevs %d\n",
 		__func__, ntohl(status), args->ndevs);
 	return status;
-err:
-	kfree(args->devs);
-	goto out;
 }
 
 static __be32 decode_sessionid(struct xdr_stream *xdr,
@@ -376,6 +372,8 @@
 
 	rc_list->rcl_nrefcalls = ntohl(*p++);
 	if (rc_list->rcl_nrefcalls) {
+		if (unlikely(rc_list->rcl_nrefcalls > xdr->buf->len))
+			goto out;
 		p = xdr_inline_decode(xdr,
 			     rc_list->rcl_nrefcalls * 2 * sizeof(uint32_t));
 		if (unlikely(p == NULL))
@@ -1069,6 +1067,7 @@
 		.pc_func = nfs4_callback_compound,
 		.pc_encode = nfs4_encode_void,
 		.pc_argsize = 256,
+		.pc_argzero = 256,
 		.pc_ressize = 256,
 		.pc_xdrressize = NFS4_CALLBACK_BUFSIZE,
 		.pc_name = "COMPOUND",
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/client.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/client.c
@@ -73,7 +73,6 @@
 	.number			= NFS_PROGRAM,
 	.nrvers			= ARRAY_SIZE(nfs_version),
 	.version		= nfs_version,
-	.stats			= &nfs_rpcstat,
 	.pipe_dir_name		= NFS_PIPE_DIRNAME,
 };
 
@@ -177,6 +176,7 @@
 	INIT_LIST_HEAD(&clp->cl_superblocks);
 	clp->cl_rpcclient = ERR_PTR(-EINVAL);
 
+	clp->cl_flags = cl_init->init_flags;
 	clp->cl_proto = cl_init->proto;
 	clp->cl_nconnect = cl_init->nconnect;
 	clp->cl_max_connect = cl_init->max_connect ? cl_init->max_connect : 1;
@@ -427,7 +427,6 @@
 			list_add_tail(&new->cl_share_link,
 					&nn->nfs_client_list);
 			spin_unlock(&nn->nfs_client_lock);
-			new->cl_flags = cl_init->init_flags;
 			return rpc_ops->init_client(new, cl_init);
 		}
 
@@ -500,6 +499,7 @@
 			  const struct nfs_client_initdata *cl_init,
 			  rpc_authflavor_t flavor)
 {
+	struct nfs_net		*nn = net_generic(clp->cl_net, nfs_net_id);
 	struct rpc_clnt		*clnt = NULL;
 	struct rpc_create_args args = {
 		.net		= clp->cl_net,
@@ -511,6 +511,7 @@
 		.servername	= clp->cl_hostname,
 		.nodename	= cl_init->nodename,
 		.program	= &nfs_program,
+		.stats		= &nn->rpcstats,
 		.version	= clp->rpc_ops->version,
 		.authflavor	= flavor,
 		.cred		= cl_init->cred,
@@ -860,6 +861,13 @@
 			server->namelen = pathinfo.max_namelen;
 	}
 
+	if (clp->rpc_ops->discover_trunking != NULL &&
+			(server->caps & NFS_CAP_FS_LOCATIONS)) {
+		error = clp->rpc_ops->discover_trunking(server, mntfh);
+		if (error < 0)
+			return error;
+	}
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(nfs_probe_fsinfo);
@@ -936,6 +944,7 @@
 	INIT_LIST_HEAD(&server->layouts);
 	INIT_LIST_HEAD(&server->state_owners_lru);
 	INIT_LIST_HEAD(&server->ss_copies);
+	INIT_LIST_HEAD(&server->ss_src_copies);
 
 	atomic_set(&server->active, 0);
 
@@ -1122,6 +1131,8 @@
 #endif
 	spin_lock_init(&nn->nfs_client_lock);
 	nn->boot_time = ktime_get_real();
+	memset(&nn->rpcstats, 0, sizeof(nn->rpcstats));
+	nn->rpcstats.program = &nfs_program;
 
 	nfs_netns_sysfs_setup(nn, net);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/delegation.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/delegation.c
@@ -228,8 +228,7 @@
  *
  */
 void nfs_inode_reclaim_delegation(struct inode *inode, const struct cred *cred,
-				  fmode_t type,
-				  const nfs4_stateid *stateid,
+				  fmode_t type, const nfs4_stateid *stateid,
 				  unsigned long pagemod_limit)
 {
 	struct nfs_delegation *delegation;
@@ -239,25 +238,24 @@
 	delegation = rcu_dereference(NFS_I(inode)->delegation);
 	if (delegation != NULL) {
 		spin_lock(&delegation->lock);
-		if (nfs4_is_valid_delegation(delegation, 0)) {
-			nfs4_stateid_copy(&delegation->stateid, stateid);
-			delegation->type = type;
-			delegation->pagemod_limit = pagemod_limit;
-			oldcred = delegation->cred;
-			delegation->cred = get_cred(cred);
-			clear_bit(NFS_DELEGATION_NEED_RECLAIM,
-				  &delegation->flags);
-			spin_unlock(&delegation->lock);
-			rcu_read_unlock();
-			put_cred(oldcred);
-			trace_nfs4_reclaim_delegation(inode, type);
-			return;
-		}
-		/* We appear to have raced with a delegation return. */
+		nfs4_stateid_copy(&delegation->stateid, stateid);
+		delegation->type = type;
+		delegation->pagemod_limit = pagemod_limit;
+		oldcred = delegation->cred;
+		delegation->cred = get_cred(cred);
+		clear_bit(NFS_DELEGATION_NEED_RECLAIM, &delegation->flags);
+		if (test_and_clear_bit(NFS_DELEGATION_REVOKED,
+				       &delegation->flags))
+			atomic_long_inc(&nfs_active_delegations);
 		spin_unlock(&delegation->lock);
+		rcu_read_unlock();
+		put_cred(oldcred);
+		trace_nfs4_reclaim_delegation(inode, type);
+	} else {
+		rcu_read_unlock();
+		nfs_inode_set_delegation(inode, cred, type, stateid,
+					 pagemod_limit);
 	}
-	rcu_read_unlock();
-	nfs_inode_set_delegation(inode, cred, type, stateid, pagemod_limit);
 }
 
 static int nfs_do_return_delegation(struct inode *inode, struct nfs_delegation *delegation, int issync)
@@ -572,17 +570,6 @@
 
 	if (test_and_clear_bit(NFS_DELEGATION_RETURN, &delegation->flags))
 		ret = true;
-	else if (test_bit(NFS_DELEGATION_RETURN_IF_CLOSED, &delegation->flags)) {
-		struct inode *inode;
-
-		spin_lock(&delegation->lock);
-		inode = delegation->inode;
-		if (inode && list_empty(&NFS_I(inode)->open_files))
-			ret = true;
-		spin_unlock(&delegation->lock);
-	}
-	if (ret)
-		clear_bit(NFS_DELEGATION_RETURN_IF_CLOSED, &delegation->flags);
 	if (test_bit(NFS_DELEGATION_RETURNING, &delegation->flags) ||
 	    test_bit(NFS_DELEGATION_RETURN_DELAYED, &delegation->flags) ||
 	    test_bit(NFS_DELEGATION_REVOKED, &delegation->flags))
@@ -629,6 +616,9 @@
 				prev = delegation;
 			continue;
 		}
+		inode = nfs_delegation_grab_inode(delegation);
+		if (inode == NULL)
+			continue;
 
 		if (prev) {
 			struct inode *tmp = nfs_delegation_grab_inode(prev);
@@ -639,12 +629,6 @@
 			}
 		}
 
-		inode = nfs_delegation_grab_inode(delegation);
-		if (inode == NULL) {
-			rcu_read_unlock();
-			iput(to_put);
-			goto restart;
-		}
 		delegation = nfs_start_delegation_return_locked(NFS_I(inode));
 		rcu_read_unlock();
 
@@ -755,11 +739,13 @@
 	struct nfs_delegation *delegation;
 
 	delegation = nfs_start_delegation_return(nfsi);
-	/* Synchronous recall of any application leases */
-	break_lease(inode, O_WRONLY | O_RDWR);
-	nfs_wb_all(inode);
-	if (delegation != NULL)
+	if (delegation != NULL) {
+		/* Synchronous recall of any application leases */
+		break_lease(inode, O_WRONLY | O_RDWR);
+		if (S_ISREG(inode->i_mode))
+			nfs_wb_all(inode);
 		return nfs_end_delegation_return(inode, delegation, 1);
+	}
 	return 0;
 }
 
@@ -824,11 +810,25 @@
 	return nfs4_inode_return_delegation(inode);
 }
 
-static void nfs_mark_return_if_closed_delegation(struct nfs_server *server,
-		struct nfs_delegation *delegation)
+static void
+nfs_mark_return_if_closed_delegation(struct nfs_server *server,
+				     struct nfs_delegation *delegation)
 {
-	set_bit(NFS_DELEGATION_RETURN_IF_CLOSED, &delegation->flags);
-	set_bit(NFS4CLNT_DELEGRETURN, &server->nfs_client->cl_state);
+	struct inode *inode;
+
+	if (test_bit(NFS_DELEGATION_RETURN, &delegation->flags) ||
+	    test_bit(NFS_DELEGATION_RETURN_IF_CLOSED, &delegation->flags))
+		return;
+	spin_lock(&delegation->lock);
+	inode = delegation->inode;
+	if (!inode)
+		goto out;
+	if (list_empty(&NFS_I(inode)->open_files))
+		nfs_mark_return_delegation(server, delegation);
+	else
+		set_bit(NFS_DELEGATION_RETURN_IF_CLOSED, &delegation->flags);
+out:
+	spin_unlock(&delegation->lock);
 }
 
 static bool nfs_server_mark_return_all_delegations(struct nfs_server *server)
@@ -984,6 +984,11 @@
 	}
 
 	nfs_mark_delegation_revoked(delegation);
+	clear_bit(NFS_DELEGATION_RETURNING, &delegation->flags);
+	spin_unlock(&delegation->lock);
+	if (nfs_detach_delegation(NFS_I(inode), delegation, NFS_SERVER(inode)))
+		nfs_put_delegation(delegation);
+	goto out_rcu_unlock;
 
 out_clear_returning:
 	clear_bit(NFS_DELEGATION_RETURNING, &delegation->flags);
@@ -1164,7 +1169,6 @@
 	struct inode *inode;
 restart:
 	rcu_read_lock();
-restart_locked:
 	list_for_each_entry_rcu(delegation, &server->delegations, super_list) {
 		if (test_bit(NFS_DELEGATION_INODE_FREEING,
 					&delegation->flags) ||
@@ -1175,7 +1179,7 @@
 			continue;
 		inode = nfs_delegation_grab_inode(delegation);
 		if (inode == NULL)
-			goto restart_locked;
+			continue;
 		delegation = nfs_start_delegation_return_locked(NFS_I(inode));
 		rcu_read_unlock();
 		if (delegation != NULL) {
@@ -1296,7 +1300,6 @@
 	nfs4_stateid stateid;
 restart:
 	rcu_read_lock();
-restart_locked:
 	list_for_each_entry_rcu(delegation, &server->delegations, super_list) {
 		if (test_bit(NFS_DELEGATION_INODE_FREEING,
 					&delegation->flags) ||
@@ -1307,7 +1310,7 @@
 			continue;
 		inode = nfs_delegation_grab_inode(delegation);
 		if (inode == NULL)
-			goto restart_locked;
+			continue;
 		spin_lock(&delegation->lock);
 		cred = get_cred_rcu(delegation->cred);
 		nfs4_stateid_copy(&stateid, &delegation->stateid);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/dir.c
@@ -78,6 +78,7 @@
 		ctx->attr_gencount = nfsi->attr_gencount;
 		ctx->dir_cookie = 0;
 		ctx->dup_cookie = 0;
+		ctx->page_index = 0;
 		spin_lock(&dir->i_lock);
 		if (list_empty(&nfsi->open_files) &&
 		    (nfsi->cache_validity & NFS_INO_DATA_INVAL_DEFER))
@@ -85,6 +86,7 @@
 					      NFS_INO_INVALID_DATA |
 						      NFS_INO_REVAL_FORCED);
 		list_add(&ctx->list, &nfsi->open_files);
+		clear_bit(NFS_INO_FORCE_READDIR, &nfsi->flags);
 		spin_unlock(&dir->i_lock);
 		return ctx;
 	}
@@ -626,8 +628,7 @@
 	if (nfs_server_capable(dir, NFS_CAP_READDIRPLUS) &&
 	    !list_empty(&nfsi->open_files)) {
 		set_bit(NFS_INO_ADVISE_RDPLUS, &nfsi->flags);
-		invalidate_mapping_pages(dir->i_mapping,
-			nfsi->page_index + 1, -1);
+		set_bit(NFS_INO_FORCE_READDIR, &nfsi->flags);
 	}
 }
 
@@ -870,7 +871,8 @@
 
 		status = nfs_readdir_page_filler(desc, entry, pages, pglen,
 						 arrays, narrays);
-	} while (!status && nfs_readdir_page_needs_filling(page));
+	} while (!status && nfs_readdir_page_needs_filling(page) &&
+		page_mapping(page));
 
 	nfs_readdir_free_pages(pages, array_size);
 out_release_label:
@@ -937,10 +939,8 @@
 			       sizeof(nfsi->cookieverf));
 	}
 	res = nfs_readdir_search_array(desc);
-	if (res == 0) {
-		nfsi->page_index = desc->page_index;
+	if (res == 0)
 		return 0;
-	}
 	nfs_readdir_page_unlock_and_put_cached(desc);
 	return res;
 }
@@ -1048,6 +1048,7 @@
 		goto out;
 
 	desc->page_index = 0;
+	desc->cache_entry_index = 0;
 	desc->last_cookie = desc->dir_cookie;
 	desc->duped = 0;
 
@@ -1079,6 +1080,7 @@
 	struct nfs_inode *nfsi = NFS_I(inode);
 	struct nfs_open_dir_context *dir_ctx = file->private_data;
 	struct nfs_readdir_descriptor *desc;
+	pgoff_t page_index;
 	int res;
 
 	dfprintk(FILE, "NFS: readdir(%pD2) starting at cookie %llu\n",
@@ -1109,10 +1111,15 @@
 	desc->dir_cookie = dir_ctx->dir_cookie;
 	desc->dup_cookie = dir_ctx->dup_cookie;
 	desc->duped = dir_ctx->duped;
+	page_index = dir_ctx->page_index;
 	desc->attr_gencount = dir_ctx->attr_gencount;
 	memcpy(desc->verf, dir_ctx->verf, sizeof(desc->verf));
 	spin_unlock(&file->f_lock);
 
+	if (test_and_clear_bit(NFS_INO_FORCE_READDIR, &nfsi->flags) &&
+	    list_is_singular(&nfsi->open_files))
+		invalidate_mapping_pages(inode->i_mapping, page_index + 1, -1);
+
 	do {
 		res = readdir_search_pagecache(desc);
 
@@ -1149,6 +1156,7 @@
 	dir_ctx->dup_cookie = desc->dup_cookie;
 	dir_ctx->duped = desc->duped;
 	dir_ctx->attr_gencount = desc->attr_gencount;
+	dir_ctx->page_index = desc->page_index;
 	memcpy(dir_ctx->verf, desc->verf, sizeof(dir_ctx->verf));
 	spin_unlock(&file->f_lock);
 
@@ -1269,13 +1277,12 @@
 static void nfs_set_verifier_locked(struct dentry *dentry, unsigned long verf)
 {
 	struct inode *inode = d_inode(dentry);
+	struct inode *dir = d_inode(dentry->d_parent);
 
-	if (!nfs_verifier_is_delegated(dentry) &&
-	    !nfs_verify_change_attribute(d_inode(dentry->d_parent), verf))
-		goto out;
+	if (!nfs_verify_change_attribute(dir, verf))
+		return;
 	if (inode && NFS_PROTO(inode)->have_delegation(inode, FMODE_READ))
 		nfs_set_verifier_delegated(&verf);
-out:
 	dentry->d_time = verf;
 }
 
@@ -1413,7 +1420,7 @@
 static void nfs_mark_dir_for_revalidate(struct inode *inode)
 {
 	spin_lock(&inode->i_lock);
-	nfs_set_cache_invalid(inode, NFS_INO_REVAL_PAGECACHE);
+	nfs_set_cache_invalid(inode, NFS_INO_INVALID_CHANGE);
 	spin_unlock(&inode->i_lock);
 }
 
@@ -1834,16 +1841,6 @@
 };
 EXPORT_SYMBOL_GPL(nfs4_dentry_operations);
 
-static fmode_t flags_to_mode(int flags)
-{
-	fmode_t res = (__force fmode_t)flags & FMODE_EXEC;
-	if ((flags & O_ACCMODE) != O_WRONLY)
-		res |= FMODE_READ;
-	if ((flags & O_ACCMODE) != O_RDONLY)
-		res |= FMODE_WRITE;
-	return res;
-}
-
 static struct nfs_open_context *create_nfs_open_context(struct dentry *dentry, int open_flags, struct file *filp)
 {
 	return alloc_nfs_open_context(dentry, flags_to_mode(open_flags), filp);
@@ -1983,6 +1980,24 @@
 
 no_open:
 	res = nfs_lookup(dir, dentry, lookup_flags);
+	if (!res) {
+		inode = d_inode(dentry);
+		if ((lookup_flags & LOOKUP_DIRECTORY) && inode &&
+		    !(S_ISDIR(inode->i_mode) || S_ISLNK(inode->i_mode)))
+			res = ERR_PTR(-ENOTDIR);
+		else if (inode && S_ISREG(inode->i_mode))
+			res = ERR_PTR(-EOPENSTALE);
+	} else if (!IS_ERR(res)) {
+		inode = d_inode(res);
+		if ((lookup_flags & LOOKUP_DIRECTORY) && inode &&
+		    !(S_ISDIR(inode->i_mode) || S_ISLNK(inode->i_mode))) {
+			dput(res);
+			res = ERR_PTR(-ENOTDIR);
+		} else if (inode && S_ISREG(inode->i_mode)) {
+			dput(res);
+			res = ERR_PTR(-EOPENSTALE);
+		}
+	}
 	if (switched) {
 		d_lookup_done(dentry);
 		if (!res)
@@ -2383,6 +2398,8 @@
 
 	trace_nfs_link_enter(inode, dir, dentry);
 	d_drop(dentry);
+	if (S_ISREG(inode->i_mode))
+		nfs_sync_inode(inode);
 	error = NFS_PROTO(dir)->link(inode, dir, &dentry->d_name);
 	if (error == 0) {
 		ihold(inode);
@@ -2471,6 +2488,8 @@
 		}
 	}
 
+	if (S_ISREG(old_inode->i_mode))
+		nfs_sync_inode(old_inode);
 	task = nfs_async_rename(old_dir, new_dir, old_dentry, new_dentry, NULL);
 	if (IS_ERR(task)) {
 		error = PTR_ERR(task);
@@ -2525,6 +2544,10 @@
 static LIST_HEAD(nfs_access_lru_list);
 static atomic_long_t nfs_access_nr_entries;
 
+static bool nfs_fasc = false;
+module_param(nfs_fasc, bool, 0644);
+MODULE_PARM_DESC(nfs_fasc, "Use file access stale cache for NFS");
+
 static unsigned long nfs_access_max_cachesize = 4*1024*1024;
 module_param(nfs_access_max_cachesize, ulong, 0644);
 MODULE_PARM_DESC(nfs_access_max_cachesize, "NFS access maximum total cache length");
@@ -2676,9 +2699,32 @@
 	return NULL;
 }
 
-static int nfs_access_get_cached_locked(struct inode *inode, const struct cred *cred, struct nfs_access_entry *res, bool may_block)
+static u64 nfs_access_login_time(const struct task_struct *task,
+				 const struct cred *cred)
+{
+	const struct task_struct *parent;
+	const struct cred *pcred;
+	u64 ret;
+
+	rcu_read_lock();
+	for (;;) {
+		parent = rcu_dereference(task->real_parent);
+		pcred = rcu_dereference(parent->cred);
+		if (parent == task || cred_fscmp(pcred, cred) != 0)
+			break;
+		task = parent;
+	}
+	ret = task->start_time;
+	rcu_read_unlock();
+	return ret;
+}
+
+static int nfs_access_get_cached_locked(struct inode *inode, const struct cred *cred, u32 *mask, bool may_block)
 {
 	struct nfs_inode *nfsi = NFS_I(inode);
+	u64 login_time;
+	if (nfs_fasc)
+		login_time = nfs_access_login_time(current, cred);
 	struct nfs_access_entry *cache;
 	bool retry = true;
 	int err;
@@ -2706,8 +2752,12 @@
 		spin_lock(&inode->i_lock);
 		retry = false;
 	}
-	res->cred = cache->cred;
-	res->mask = cache->mask;
+	if (nfs_fasc) {
+		err = -ENOENT;
+		if ((s64)(login_time - cache->timestamp) > 0)
+			goto out;
+	}
+	*mask = cache->mask;
 	list_move_tail(&cache->lru, &nfsi->access_cache_entry_lru);
 	err = 0;
 out:
@@ -2719,12 +2769,15 @@
 	return -ENOENT;
 }
 
-static int nfs_access_get_cached_rcu(struct inode *inode, const struct cred *cred, struct nfs_access_entry *res)
+static int nfs_access_get_cached_rcu(struct inode *inode, const struct cred *cred, u32 *mask)
 {
 	/* Only check the most recently returned cache entry,
 	 * but do it without locking.
 	 */
 	struct nfs_inode *nfsi = NFS_I(inode);
+	u64 login_time;
+	if (nfs_fasc)
+		login_time = nfs_access_login_time(current, cred);
 	struct nfs_access_entry *cache;
 	int err = -ECHILD;
 	struct list_head *lh;
@@ -2739,24 +2792,27 @@
 		cache = NULL;
 	if (cache == NULL)
 		goto out;
+	if (nfs_fasc) {
+		if ((s64)(login_time - cache->timestamp) > 0)
+			goto out;
+	}
 	if (nfs_check_cache_invalid(inode, NFS_INO_INVALID_ACCESS))
 		goto out;
-	res->cred = cache->cred;
-	res->mask = cache->mask;
+	*mask = cache->mask;
 	err = 0;
 out:
 	rcu_read_unlock();
 	return err;
 }
 
-int nfs_access_get_cached(struct inode *inode, const struct cred *cred, struct
-nfs_access_entry *res, bool may_block)
+int nfs_access_get_cached(struct inode *inode, const struct cred *cred,
+			  u32 *mask, bool may_block)
 {
 	int status;
 
-	status = nfs_access_get_cached_rcu(inode, cred, res);
+	status = nfs_access_get_cached_rcu(inode, cred, mask);
 	if (status != 0)
-		status = nfs_access_get_cached_locked(inode, cred, res,
+		status = nfs_access_get_cached_locked(inode, cred, mask,
 		    may_block);
 
 	return status;
@@ -2806,6 +2862,8 @@
 	RB_CLEAR_NODE(&cache->rb_node);
 	cache->cred = get_cred(set->cred);
 	cache->mask = set->mask;
+	if (nfs_fasc)
+		cache->timestamp = ktime_get_ns();
 
 	/* The above field assignments must be visible
 	 * before this item appears on the lru.  We cannot easily
@@ -2877,7 +2935,7 @@
 
 	trace_nfs_access_enter(inode);
 
-	status = nfs_access_get_cached(inode, cred, &cache, may_block);
+	status = nfs_access_get_cached(inode, cred, &cache.mask, may_block);
 	if (status == 0)
 		goto out_cached;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/direct.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/direct.c
@@ -172,8 +172,8 @@
 	VM_BUG_ON(iov_iter_count(iter) != PAGE_SIZE);
 
 	if (iov_iter_rw(iter) == READ)
-		return nfs_file_direct_read(iocb, iter);
-	return nfs_file_direct_write(iocb, iter);
+		return nfs_file_direct_read(iocb, iter, true);
+	return nfs_file_direct_write(iocb, iter, true);
 }
 
 static void nfs_direct_release_pages(struct page **pages, unsigned int npages)
@@ -424,6 +424,7 @@
  * nfs_file_direct_read - file direct read operation for NFS files
  * @iocb: target I/O control block
  * @iter: vector of user buffers into which to read data
+ * @swap: flag indicating this is swap IO, not O_DIRECT IO
  *
  * We use this function for direct reads instead of calling
  * generic_file_aio_read() in order to avoid gfar's check to see if
@@ -439,7 +440,8 @@
  * client must read the updated atime from the server back into its
  * cache.
  */
-ssize_t nfs_file_direct_read(struct kiocb *iocb, struct iov_iter *iter)
+ssize_t nfs_file_direct_read(struct kiocb *iocb, struct iov_iter *iter,
+			     bool swap)
 {
 	struct file *file = iocb->ki_filp;
 	struct address_space *mapping = file->f_mapping;
@@ -481,12 +483,14 @@
 	if (iter_is_iovec(iter))
 		dreq->flags = NFS_ODIRECT_SHOULD_DIRTY;
 
-	nfs_start_io_direct(inode);
+	if (!swap)
+		nfs_start_io_direct(inode);
 
 	NFS_I(inode)->read_io += count;
 	requested = nfs_direct_read_schedule_iovec(dreq, iter, iocb->ki_pos);
 
-	nfs_end_io_direct(inode);
+	if (!swap)
+		nfs_end_io_direct(inode);
 
 	if (requested > 0) {
 		result = nfs_direct_wait(dreq);
@@ -505,21 +509,47 @@
 	return result;
 }
 
-static void
-nfs_direct_join_group(struct list_head *list, struct inode *inode)
+static void nfs_direct_add_page_head(struct list_head *list,
+				     struct nfs_page *req)
 {
-	struct nfs_page *req, *next;
+	struct nfs_page *head = req->wb_head;
+
+	if (!list_empty(&head->wb_list) || !nfs_lock_request(head))
+		return;
+	if (!list_empty(&head->wb_list)) {
+		nfs_unlock_request(head);
+		return;
+	}
+	list_add(&head->wb_list, list);
+	kref_get(&head->wb_kref);
+	kref_get(&head->wb_kref);
+}
+
+static void nfs_direct_join_group(struct list_head *list,
+				  struct nfs_commit_info *cinfo,
+				  struct inode *inode)
+{
+	struct nfs_page *req, *subreq;
 
 	list_for_each_entry(req, list, wb_list) {
-		if (req->wb_head != req || req->wb_this_page == req)
+		if (req->wb_head != req) {
+			nfs_direct_add_page_head(&req->wb_list, req);
 			continue;
-		for (next = req->wb_this_page;
-				next != req->wb_head;
-				next = next->wb_this_page) {
-			nfs_list_remove_request(next);
-			nfs_release_request(next);
 		}
-		nfs_join_page_group(req, inode);
+		subreq = req->wb_this_page;
+		if (subreq == req)
+			continue;
+		do {
+			/*
+			 * Remove subrequests from this list before freeing
+			 * them in the call to nfs_join_page_group().
+			 */
+			if (!list_empty(&subreq->wb_list)) {
+				nfs_list_remove_request(subreq);
+				nfs_release_request(subreq);
+			}
+		} while ((subreq = subreq->wb_this_page) != req);
+		nfs_join_page_group(req, cinfo, inode);
 	}
 }
 
@@ -545,7 +575,7 @@
 	nfs_init_cinfo_from_dreq(&cinfo, dreq);
 	nfs_direct_write_scan_commit_list(dreq->inode, &reqs, &cinfo);
 
-	nfs_direct_join_group(&reqs, dreq->inode);
+	nfs_direct_join_group(&reqs, &cinfo, dreq->inode);
 
 	dreq->count = 0;
 	dreq->max_count = 0;
@@ -620,7 +650,7 @@
 		nfs_unlock_and_release_request(req);
 	}
 
-	if (atomic_dec_and_test(&cinfo.mds->rpcs_out))
+	if (nfs_commit_end(cinfo.mds))
 		nfs_direct_write_complete(dreq);
 }
 
@@ -648,10 +678,17 @@
 	LIST_HEAD(mds_list);
 
 	nfs_init_cinfo_from_dreq(&cinfo, dreq);
+	nfs_commit_begin(cinfo.mds);
 	nfs_scan_commit(dreq->inode, &mds_list, &cinfo);
 	res = nfs_generic_commit_list(dreq->inode, &mds_list, 0, &cinfo);
-	if (res < 0) /* res == -ENOMEM */
-		nfs_direct_write_reschedule(dreq);
+	if (res < 0) { /* res == -ENOMEM */
+		spin_lock(&dreq->lock);
+		if (dreq->flags == 0)
+			dreq->flags = NFS_ODIRECT_RESCHED_WRITES;
+		spin_unlock(&dreq->lock);
+	}
+	if (nfs_commit_end(cinfo.mds))
+		nfs_direct_write_complete(dreq);
 }
 
 static void nfs_direct_write_clear_reqs(struct nfs_direct_req *dreq)
@@ -756,16 +793,21 @@
 static void nfs_direct_write_reschedule_io(struct nfs_pgio_header *hdr)
 {
 	struct nfs_direct_req *dreq = hdr->dreq;
+	struct nfs_page *req;
+	struct nfs_commit_info cinfo;
 
+	nfs_init_cinfo_from_dreq(&cinfo, dreq);
 	spin_lock(&dreq->lock);
-	if (dreq->error == 0) {
+	if (dreq->error == 0)
 		dreq->flags = NFS_ODIRECT_RESCHED_WRITES;
-		/* fake unstable write to let common nfs resend pages */
-		hdr->verf.committed = NFS_UNSTABLE;
-		hdr->good_bytes = hdr->args.offset + hdr->args.count -
-			hdr->io_start;
-	}
+	set_bit(NFS_IOHDR_REDO, &hdr->flags);
 	spin_unlock(&dreq->lock);
+	while (!list_empty(&hdr->pages)) {
+		req = nfs_list_entry(hdr->pages.next);
+		nfs_list_remove_request(req);
+		nfs_unlock_request(req);
+		nfs_mark_request_commit(req, NULL, &cinfo, 0);
+	}
 }
 
 static const struct nfs_pgio_completion_ops nfs_direct_write_completion_ops = {
@@ -789,7 +831,7 @@
  */
 static ssize_t nfs_direct_write_schedule_iovec(struct nfs_direct_req *dreq,
 					       struct iov_iter *iter,
-					       loff_t pos)
+					       loff_t pos, int ioflags)
 {
 	struct nfs_pageio_descriptor desc;
 	struct inode *inode = dreq->inode;
@@ -797,7 +839,7 @@
 	size_t requested_bytes = 0;
 	size_t wsize = max_t(size_t, NFS_SERVER(inode)->wsize, PAGE_SIZE);
 
-	nfs_pageio_init_write(&desc, inode, FLUSH_COND_STABLE, false,
+	nfs_pageio_init_write(&desc, inode, ioflags, false,
 			      &nfs_direct_write_completion_ops);
 	desc.pg_dreq = dreq;
 	get_dreq(dreq);
@@ -875,6 +917,7 @@
  * nfs_file_direct_write - file direct write operation for NFS files
  * @iocb: target I/O control block
  * @iter: vector of user buffers from which to write data
+ * @swap: flag indicating this is swap IO, not O_DIRECT IO
  *
  * We use this function for direct writes instead of calling
  * generic_file_aio_write() in order to avoid taking the inode
@@ -891,7 +934,8 @@
  * Note that O_APPEND is not supported for NFS direct writes, as there
  * is no atomic O_APPEND write facility in the NFS protocol.
  */
-ssize_t nfs_file_direct_write(struct kiocb *iocb, struct iov_iter *iter)
+ssize_t nfs_file_direct_write(struct kiocb *iocb, struct iov_iter *iter,
+			      bool swap)
 {
 	ssize_t result, requested;
 	size_t count;
@@ -905,7 +949,11 @@
 	dfprintk(FILE, "NFS: direct write(%pD2, %zd@%Ld)\n",
 		file, iov_iter_count(iter), (long long) iocb->ki_pos);
 
-	result = generic_write_checks(iocb, iter);
+	if (swap)
+		/* bypass generic checks */
+		result =  iov_iter_count(iter);
+	else
+		result = generic_write_checks(iocb, iter);
 	if (result <= 0)
 		return result;
 	count = result;
@@ -936,17 +984,23 @@
 		dreq->iocb = iocb;
 	pnfs_init_ds_commit_info_ops(&dreq->ds_cinfo, inode);
 
-	nfs_start_io_direct(inode);
+	if (swap) {
+		requested = nfs_direct_write_schedule_iovec(dreq, iter, pos,
+							    FLUSH_STABLE);
+	} else {
+		nfs_start_io_direct(inode);
+
+		requested = nfs_direct_write_schedule_iovec(dreq, iter, pos,
+							    FLUSH_COND_STABLE);
 
-	requested = nfs_direct_write_schedule_iovec(dreq, iter, pos);
+		if (mapping->nrpages) {
+			invalidate_inode_pages2_range(mapping,
+						      pos >> PAGE_SHIFT, end);
+		}
 
-	if (mapping->nrpages) {
-		invalidate_inode_pages2_range(mapping,
-					      pos >> PAGE_SHIFT, end);
+		nfs_end_io_direct(inode);
 	}
 
-	nfs_end_io_direct(inode);
-
 	if (requested > 0) {
 		result = nfs_direct_wait(dreq);
 		if (result > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/export.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/export.c
@@ -178,7 +178,10 @@
 	.fh_to_dentry = nfs_fh_to_dentry,
 	.get_parent = nfs_get_parent,
 	.fetch_iversion = nfs_fetch_iversion,
-	.flags = EXPORT_OP_NOWCC|EXPORT_OP_NOSUBTREECHK|
-		EXPORT_OP_CLOSE_BEFORE_UNLINK|EXPORT_OP_REMOTE_FS|
-		EXPORT_OP_NOATOMIC_ATTR|EXPORT_OP_SYNC_LOCKS,
+	.flags = EXPORT_OP_NOWCC		|
+		 EXPORT_OP_NOSUBTREECHK		|
+		 EXPORT_OP_CLOSE_BEFORE_UNLINK	|
+		 EXPORT_OP_REMOTE_FS		|
+		 EXPORT_OP_NOATOMIC_ATTR	|
+		 EXPORT_OP_FLUSH_ON_CLOSE,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/file.c
@@ -161,7 +161,7 @@
 	ssize_t result;
 
 	if (iocb->ki_flags & IOCB_DIRECT)
-		return nfs_file_direct_read(iocb, to);
+		return nfs_file_direct_read(iocb, to, false);
 
 	dprintk("NFS: read(%pD2, %zu@%lu)\n",
 		iocb->ki_filp,
@@ -208,22 +208,25 @@
 nfs_file_fsync_commit(struct file *file, int datasync)
 {
 	struct inode *inode = file_inode(file);
-	int ret;
+	int ret, ret2;
 
 	dprintk("NFS: fsync file(%pD2) datasync %d\n", file, datasync);
 
 	nfs_inc_stats(inode, NFSIOS_VFSFSYNC);
 	ret = nfs_commit_inode(inode, FLUSH_SYNC);
-	if (ret < 0)
-		return ret;
-	return file_check_and_advance_wb_err(file);
+	ret2 = file_check_and_advance_wb_err(file);
+	if (ret2 < 0)
+		return ret2;
+	return ret;
 }
 
 int
 nfs_file_fsync(struct file *file, loff_t start, loff_t end, int datasync)
 {
-	struct nfs_open_context *ctx = nfs_file_open_context(file);
 	struct inode *inode = file_inode(file);
+	struct nfs_inode *nfsi = NFS_I(inode);
+	long save_nredirtied = atomic_long_read(&nfsi->redirtied_pages);
+	long nredirtied;
 	int ret;
 
 	trace_nfs_fsync_enter(inode);
@@ -238,15 +241,10 @@
 		ret = pnfs_sync_inode(inode, !!datasync);
 		if (ret != 0)
 			break;
-		if (!test_and_clear_bit(NFS_CONTEXT_RESEND_WRITES, &ctx->flags))
+		nredirtied = atomic_long_read(&nfsi->redirtied_pages);
+		if (nredirtied == save_nredirtied)
 			break;
-		/*
-		 * If nfs_file_fsync_commit detected a server reboot, then
-		 * resend all dirty pages that might have been covered by
-		 * the NFS_CONTEXT_RESEND_WRITES flag
-		 */
-		start = 0;
-		end = LLONG_MAX;
+		save_nredirtied = nredirtied;
 	}
 
 	trace_nfs_fsync_exit(inode, ret);
@@ -389,11 +387,8 @@
 		return status;
 	NFS_I(mapping->host)->write_io += copied;
 
-	if (nfs_ctx_key_to_expire(ctx, mapping->host)) {
-		status = nfs_wb_all(mapping->host);
-		if (status < 0)
-			return status;
-	}
+	if (nfs_ctx_key_to_expire(ctx, mapping->host))
+		nfs_wb_all(mapping->host);
 
 	return copied;
 }
@@ -489,8 +484,9 @@
 {
 	unsigned long blocks;
 	long long isize;
-	struct rpc_clnt *clnt = NFS_CLIENT(file->f_mapping->host);
-	struct inode *inode = file->f_mapping->host;
+	struct inode *inode = file_inode(file);
+	struct rpc_clnt *clnt = NFS_CLIENT(inode);
+	struct nfs_client *cl = NFS_SERVER(inode)->nfs_client;
 
 	spin_lock(&inode->i_lock);
 	blocks = inode->i_blocks;
@@ -503,14 +499,22 @@
 
 	*span = sis->pages;
 
+
+	if (cl->rpc_ops->enable_swap)
+		cl->rpc_ops->enable_swap(inode);
+
 	return rpc_clnt_swap_activate(clnt);
 }
 
 static void nfs_swap_deactivate(struct file *file)
 {
-	struct rpc_clnt *clnt = NFS_CLIENT(file->f_mapping->host);
+	struct inode *inode = file_inode(file);
+	struct rpc_clnt *clnt = NFS_CLIENT(inode);
+	struct nfs_client *cl = NFS_SERVER(inode)->nfs_client;
 
 	rpc_clnt_swap_deactivate(clnt);
+	if (cl->rpc_ops->disable_swap)
+		cl->rpc_ops->disable_swap(file_inode(file));
 }
 
 const struct address_space_operations nfs_file_aops = {
@@ -590,18 +594,6 @@
 	.page_mkwrite = nfs_vm_page_mkwrite,
 };
 
-static int nfs_need_check_write(struct file *filp, struct inode *inode,
-				int error)
-{
-	struct nfs_open_context *ctx;
-
-	ctx = nfs_file_open_context(filp);
-	if (nfs_error_is_fatal_on_server(error) ||
-	    nfs_ctx_key_to_expire(ctx, inode))
-		return 1;
-	return 0;
-}
-
 ssize_t nfs_file_write(struct kiocb *iocb, struct iov_iter *from)
 {
 	struct file *file = iocb->ki_filp;
@@ -616,7 +608,7 @@
 		return result;
 
 	if (iocb->ki_flags & IOCB_DIRECT)
-		return nfs_file_direct_write(iocb, from);
+		return nfs_file_direct_write(iocb, from, false);
 
 	dprintk("NFS: write(%pD2, %zu@%Ld)\n",
 		file, iov_iter_count(from), (long long) iocb->ki_pos);
@@ -629,7 +621,7 @@
 	if (iocb->ki_flags & IOCB_APPEND || iocb->ki_pos > i_size_read(inode)) {
 		result = nfs_revalidate_file_size(inode, file);
 		if (result)
-			goto out;
+			return result;
 	}
 
 	nfs_clear_invalid_mapping(file->f_mapping);
@@ -648,6 +640,7 @@
 
 	written = result;
 	iocb->ki_pos += written;
+	nfs_add_stats(inode, NFSIOS_NORMALWRITTENBYTES, written);
 
 	if (mntflags & NFS_MOUNT_WRITE_EAGER) {
 		result = filemap_fdatawrite_range(file->f_mapping,
@@ -665,17 +658,22 @@
 	}
 	result = generic_write_sync(iocb, written);
 	if (result < 0)
-		goto out;
+		return result;
 
+out:
 	/* Return error values */
 	error = filemap_check_wb_err(file->f_mapping, since);
-	if (nfs_need_check_write(file, inode, error)) {
-		int err = nfs_wb_all(inode);
-		if (err < 0)
-			result = err;
+	switch (error) {
+	default:
+		break;
+	case -EDQUOT:
+	case -EFBIG:
+	case -ENOSPC:
+		nfs_wb_all(inode);
+		error = file_check_and_advance_wb_err(file);
+		if (error < 0)
+			result = error;
 	}
-	nfs_add_stats(inode, NFSIOS_NORMALWRITTENBYTES, written);
-out:
 	return result;
 
 out_swapfile:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/filelayout/filelayout.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/filelayout/filelayout.c
@@ -783,6 +783,12 @@
 	return &fl->generic_hdr;
 }
 
+static bool
+filelayout_lseg_is_striped(const struct nfs4_filelayout_segment *flseg)
+{
+	return flseg->num_fh > 1;
+}
+
 /*
  * filelayout_pg_test(). Called by nfs_can_coalesce_requests()
  *
@@ -803,6 +809,8 @@
 	size = pnfs_generic_pg_test(pgio, prev, req);
 	if (!size)
 		return 0;
+	else if (!filelayout_lseg_is_striped(FILELAYOUT_LSEG(pgio->pg_lseg)))
+		return size;
 
 	/* see if req and prev are in the same stripe */
 	if (prev) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/flexfilelayout/flexfilelayout.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/flexfilelayout/flexfilelayout.c
@@ -836,6 +836,9 @@
 	struct nfs4_pnfs_ds *ds;
 	u32 ds_idx;
 
+	if (NFS_SERVER(pgio->pg_inode)->flags &
+			(NFS_MOUNT_SOFT|NFS_MOUNT_SOFTERR))
+		pgio->pg_maxretrans = io_maxretrans;
 retry:
 	ff_layout_pg_check_layout(pgio, req);
 	/* Use full layout for now */
@@ -849,6 +852,8 @@
 		if (!pgio->pg_lseg)
 			goto out_nolseg;
 	}
+	/* Reset wb_nio, since getting layout segment was successful */
+	req->wb_nio = 0;
 
 	ds = ff_layout_get_ds_for_read(pgio, &ds_idx);
 	if (!ds) {
@@ -865,14 +870,24 @@
 	pgm->pg_bsize = mirror->mirror_ds->ds_versions[0].rsize;
 
 	pgio->pg_mirror_idx = ds_idx;
-
-	if (NFS_SERVER(pgio->pg_inode)->flags &
-			(NFS_MOUNT_SOFT|NFS_MOUNT_SOFTERR))
-		pgio->pg_maxretrans = io_maxretrans;
 	return;
 out_nolseg:
-	if (pgio->pg_error < 0)
-		return;
+	if (pgio->pg_error < 0) {
+		if (pgio->pg_error != -EAGAIN)
+			return;
+		/* Retry getting layout segment if lower layer returned -EAGAIN */
+		if (pgio->pg_maxretrans && req->wb_nio++ > pgio->pg_maxretrans) {
+			if (NFS_SERVER(pgio->pg_inode)->flags & NFS_MOUNT_SOFTERR)
+				pgio->pg_error = -ETIMEDOUT;
+			else
+				pgio->pg_error = -EIO;
+			return;
+		}
+		pgio->pg_error = 0;
+		/* Sleep for 1 second before retrying */
+		ssleep(1);
+		goto retry;
+	}
 out_mds:
 	trace_pnfs_mds_fallback_pg_init_read(pgio->pg_inode,
 			0, NFS4_MAX_UINT64, IOMODE_READ,
@@ -1140,6 +1155,8 @@
 	case -EIO:
 	case -ETIMEDOUT:
 	case -EPIPE:
+	case -EPROTO:
+	case -ENODEV:
 		dprintk("%s DS connection error %d\n", __func__,
 			task->tk_status);
 		nfs4_delete_deviceid(devid->ld, devid->nfs_client,
@@ -1236,6 +1253,7 @@
 		case -EPFNOSUPPORT:
 		case -EPROTONOSUPPORT:
 		case -EOPNOTSUPP:
+		case -EINVAL:
 		case -ECONNREFUSED:
 		case -ECONNRESET:
 		case -EHOSTDOWN:
@@ -1245,6 +1263,8 @@
 		case -ENOBUFS:
 		case -EPIPE:
 		case -EPERM:
+		case -EPROTO:
+		case -ENODEV:
 			*op_status = status = NFS4ERR_NXIO;
 			break;
 		case -EACCES:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/flexfilelayout/flexfilelayoutdev.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/flexfilelayout/flexfilelayoutdev.c
@@ -378,10 +378,10 @@
 		goto noconnect;
 
 	ds = mirror->mirror_ds->ds;
+	if (READ_ONCE(ds->ds_clp))
+		goto out;
 	/* matching smp_wmb() in _nfs4_pnfs_v3/4_ds_connect */
 	smp_rmb();
-	if (ds->ds_clp)
-		goto out;
 
 	/* FIXME: For now we assume the server sent only one version of NFS
 	 * to use for the DS.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/fs_context.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/fs_context.c
@@ -514,7 +514,7 @@
 		if (result.negated)
 			ctx->flags &= ~NFS_MOUNT_SOFTREVAL;
 		else
-			ctx->flags &= NFS_MOUNT_SOFTREVAL;
+			ctx->flags |= NFS_MOUNT_SOFTREVAL;
 		break;
 	case Opt_posix:
 		if (result.negated)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/getroot.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/getroot.c
@@ -80,18 +80,15 @@
 		goto out;
 
 	/* get the actual root for this mount */
-	fsinfo.fattr = nfs_alloc_fattr();
+	fsinfo.fattr = nfs_alloc_fattr_with_label(server);
 	if (fsinfo.fattr == NULL)
 		goto out_name;
 
-	fsinfo.fattr->label = nfs4_label_alloc(server, GFP_KERNEL);
-	if (IS_ERR(fsinfo.fattr->label))
-		goto out_fattr;
 	error = server->nfs_client->rpc_ops->getroot(server, ctx->mntfh, &fsinfo);
 	if (error < 0) {
 		dprintk("nfs_get_root: getattr error = %d\n", -error);
 		nfs_errorf(fc, "NFS: Couldn't getattr on root");
-		goto out_label;
+		goto out_fattr;
 	}
 
 	inode = nfs_fhget(s, ctx->mntfh, fsinfo.fattr, NULL);
@@ -99,12 +96,12 @@
 		dprintk("nfs_get_root: get root inode failed\n");
 		error = PTR_ERR(inode);
 		nfs_errorf(fc, "NFS: Couldn't get root inode");
-		goto out_label;
+		goto out_fattr;
 	}
 
 	error = nfs_superblock_set_dummy_root(s, inode);
 	if (error != 0)
-		goto out_label;
+		goto out_fattr;
 
 	/* root dentries normally start off anonymous and get spliced in later
 	 * if the dentry tree reaches them; however if the dentry already
@@ -115,7 +112,7 @@
 		dprintk("nfs_get_root: get root dentry failed\n");
 		error = PTR_ERR(root);
 		nfs_errorf(fc, "NFS: Couldn't get root dentry");
-		goto out_label;
+		goto out_fattr;
 	}
 
 	security_d_instantiate(root, inode);
@@ -154,8 +151,6 @@
 	nfs_setsecurity(inode, fsinfo.fattr, fsinfo.fattr->label);
 	error = 0;
 
-out_label:
-	nfs4_label_free(fsinfo.fattr->label);
 out_fattr:
 	nfs_free_fattr(fsinfo.fattr);
 out_name:
@@ -165,5 +160,5 @@
 error_splat_root:
 	dput(fc->root);
 	fc->root = NULL;
-	goto out_label;
+	goto out_fattr;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/inode.c
@@ -210,10 +210,20 @@
 		flags &= ~NFS_INO_INVALID_XATTR;
 	if (flags & NFS_INO_INVALID_DATA)
 		nfs_fscache_invalidate(inode);
-	if (inode->i_mapping->nrpages == 0)
-		flags &= ~(NFS_INO_INVALID_DATA|NFS_INO_DATA_INVAL_DEFER);
 	flags &= ~(NFS_INO_REVAL_PAGECACHE | NFS_INO_REVAL_FORCED);
-	nfsi->cache_validity |= flags;
+
+	flags |= nfsi->cache_validity;
+	if (inode->i_mapping->nrpages == 0)
+		flags &= ~NFS_INO_INVALID_DATA;
+
+	/* pairs with nfs_clear_invalid_mapping()'s smp_load_acquire() */
+	smp_store_release(&nfsi->cache_validity, flags);
+
+	if (inode->i_mapping->nrpages == 0 ||
+	    nfsi->cache_validity & NFS_INO_INVALID_DATA) {
+		nfs_ooo_clear(nfsi);
+	}
+	trace_nfs_set_cache_invalid(inode, 0);
 }
 EXPORT_SYMBOL_GPL(nfs_set_cache_invalid);
 
@@ -426,6 +436,23 @@
 	return inode;
 }
 
+static void nfs_inode_init_regular(struct nfs_inode *nfsi)
+{
+	atomic_long_set(&nfsi->nrequests, 0);
+	atomic_long_set(&nfsi->redirtied_pages, 0);
+	INIT_LIST_HEAD(&nfsi->commit_info.list);
+	atomic_long_set(&nfsi->commit_info.ncommit, 0);
+	atomic_set(&nfsi->commit_info.rpcs_out, 0);
+	mutex_init(&nfsi->commit_mutex);
+}
+
+static void nfs_inode_init_dir(struct nfs_inode *nfsi)
+{
+	nfsi->cache_change_attribute = 0;
+	memset(nfsi->cookieverf, 0, sizeof(nfsi->cookieverf));
+	init_rwsem(&nfsi->rmdir_sem);
+}
+
 /*
  * This is our front-end to iget that looks up inodes by file handle
  * instead of inode number.
@@ -480,10 +507,12 @@
 		if (S_ISREG(inode->i_mode)) {
 			inode->i_fop = NFS_SB(sb)->nfs_client->rpc_ops->file_ops;
 			inode->i_data.a_ops = &nfs_file_aops;
+			nfs_inode_init_regular(nfsi);
 		} else if (S_ISDIR(inode->i_mode)) {
 			inode->i_op = NFS_SB(sb)->nfs_client->rpc_ops->dir_inode_ops;
 			inode->i_fop = &nfs_dir_operations;
 			inode->i_data.a_ops = &nfs_dir_aops;
+			nfs_inode_init_dir(nfsi);
 			/* Deal with crossing mountpoints */
 			if (fattr->valid & NFS_ATTR_FATTR_MOUNTPOINT ||
 					fattr->valid & NFS_ATTR_FATTR_V4_REFERRAL) {
@@ -509,7 +538,6 @@
 		inode->i_uid = make_kuid(&init_user_ns, -2);
 		inode->i_gid = make_kgid(&init_user_ns, -2);
 		inode->i_blocks = 0;
-		memset(nfsi->cookieverf, 0, sizeof(nfsi->cookieverf));
 		nfsi->write_io = 0;
 		nfsi->read_io = 0;
 
@@ -668,9 +696,10 @@
 
 	i_size_write(inode, offset);
 	/* Optimisation */
-	if (offset == 0)
-		NFS_I(inode)->cache_validity &= ~(NFS_INO_INVALID_DATA |
-				NFS_INO_DATA_INVAL_DEFER);
+	if (offset == 0) {
+		NFS_I(inode)->cache_validity &= ~NFS_INO_INVALID_DATA;
+		nfs_ooo_clear(NFS_I(inode));
+	}
 	NFS_I(inode)->cache_validity &= ~NFS_INO_INVALID_SIZE;
 
 	spin_unlock(&inode->i_lock);
@@ -708,9 +737,7 @@
 		if ((attr->ia_valid & ATTR_KILL_SUID) != 0 &&
 		    inode->i_mode & S_ISUID)
 			inode->i_mode &= ~S_ISUID;
-		if ((attr->ia_valid & ATTR_KILL_SGID) != 0 &&
-		    (inode->i_mode & (S_ISGID | S_IXGRP)) ==
-		     (S_ISGID | S_IXGRP))
+		if (setattr_should_drop_sgid(&init_user_ns, inode))
 			inode->i_mode &= ~S_ISGID;
 		if ((attr->ia_valid & ATTR_MODE) != 0) {
 			int mode = attr->ia_mode & S_IALLUGO;
@@ -835,12 +862,9 @@
 	}
 
 	/* Flush out writes to the server in order to update c/mtime.  */
-	if ((request_mask & (STATX_CTIME|STATX_MTIME)) &&
-			S_ISREG(inode->i_mode)) {
-		err = filemap_write_and_wait(inode->i_mapping);
-		if (err)
-			goto out;
-	}
+	if ((request_mask & (STATX_CTIME | STATX_MTIME)) &&
+	    S_ISREG(inode->i_mode))
+		filemap_write_and_wait(inode->i_mapping);
 
 	/*
 	 * We may force a getattr if the user cares about atime.
@@ -1024,7 +1048,7 @@
 		ctx->cred = get_cred(filp->f_cred);
 	else
 		ctx->cred = get_current_cred();
-	ctx->ll_cred = NULL;
+	rcu_assign_pointer(ctx->ll_cred, NULL);
 	ctx->state = NULL;
 	ctx->mode = f_mode;
 	ctx->flags = 0;
@@ -1063,7 +1087,7 @@
 	put_cred(ctx->cred);
 	dput(ctx->dentry);
 	nfs_sb_deactive(sb);
-	put_rpccred(ctx->ll_cred);
+	put_rpccred(rcu_dereference_protected(ctx->ll_cred, 1));
 	kfree(ctx->mdsthreshold);
 	kfree_rcu(ctx, rcu_head);
 }
@@ -1090,7 +1114,7 @@
 
 	spin_lock(&inode->i_lock);
 	if (list_empty(&nfsi->open_files) &&
-	    (nfsi->cache_validity & NFS_INO_DATA_INVAL_DEFER))
+	    nfs_ooo_test(nfsi))
 		nfs_set_cache_invalid(inode, NFS_INO_INVALID_DATA |
 						     NFS_INO_REVAL_FORCED);
 	list_add_tail_rcu(&ctx->list, &nfsi->open_files);
@@ -1165,7 +1189,6 @@
 	nfs_fscache_open_file(inode, filp);
 	return 0;
 }
-EXPORT_SYMBOL_GPL(nfs_open);
 
 /*
  * This function is called whenever some part of NFS notices that
@@ -1330,6 +1353,13 @@
 					 nfs_wait_bit_killable, TASK_KILLABLE);
 		if (ret)
 			goto out;
+		smp_rmb(); /* pairs with smp_wmb() below */
+		if (test_bit(NFS_INO_INVALIDATING, bitlock))
+			continue;
+		/* pairs with nfs_set_cache_invalid()'s smp_store_release() */
+		if (!(smp_load_acquire(&nfsi->cache_validity) & NFS_INO_INVALID_DATA))
+			goto out;
+		/* Slow-path that double-checks with spinlock held */
 		spin_lock(&inode->i_lock);
 		if (test_bit(NFS_INO_INVALIDATING, bitlock)) {
 			spin_unlock(&inode->i_lock);
@@ -1343,8 +1373,8 @@
 
 	set_bit(NFS_INO_INVALIDATING, bitlock);
 	smp_wmb();
-	nfsi->cache_validity &=
-		~(NFS_INO_INVALID_DATA | NFS_INO_DATA_INVAL_DEFER);
+	nfsi->cache_validity &= ~NFS_INO_INVALID_DATA;
+	nfs_ooo_clear(nfsi);
 	spin_unlock(&inode->i_lock);
 	trace_nfs_invalidate_mapping_enter(inode);
 	ret = nfs_invalidate_mapping(inode, mapping);
@@ -1556,6 +1586,7 @@
 	fattr->gencount = nfs_inc_attr_generation_counter();
 	fattr->owner_name = NULL;
 	fattr->group_name = NULL;
+	fattr->mdsthreshold = NULL;
 }
 EXPORT_SYMBOL_GPL(nfs_fattr_init);
 
@@ -1579,18 +1610,37 @@
 {
 	struct nfs_fattr *fattr;
 
-	fattr = kmalloc(sizeof(*fattr), GFP_NOFS);
-	if (fattr != NULL)
+	fattr = kmalloc(sizeof(*fattr), GFP_KERNEL);
+	if (fattr != NULL) {
 		nfs_fattr_init(fattr);
+		fattr->label = NULL;
+	}
 	return fattr;
 }
 EXPORT_SYMBOL_GPL(nfs_alloc_fattr);
 
+struct nfs_fattr *nfs_alloc_fattr_with_label(struct nfs_server *server)
+{
+	struct nfs_fattr *fattr = nfs_alloc_fattr();
+
+	if (!fattr)
+		return NULL;
+
+	fattr->label = nfs4_label_alloc(server, GFP_KERNEL);
+	if (IS_ERR(fattr->label)) {
+		kfree(fattr);
+		return NULL;
+	}
+
+	return fattr;
+}
+EXPORT_SYMBOL_GPL(nfs_alloc_fattr_with_label);
+
 struct nfs_fh *nfs_alloc_fhandle(void)
 {
 	struct nfs_fh *fh;
 
-	fh = kmalloc(sizeof(struct nfs_fh), GFP_NOFS);
+	fh = kmalloc(sizeof(struct nfs_fh), GFP_KERNEL);
 	if (fh != NULL)
 		fh->size = 0;
 	return fh;
@@ -1777,8 +1827,10 @@
 		NFS_INO_INVALID_BLOCKS | NFS_INO_INVALID_OTHER |
 		NFS_INO_INVALID_NLINK;
 	unsigned long cache_validity = NFS_I(inode)->cache_validity;
+	enum nfs4_change_attr_type ctype = NFS_SERVER(inode)->change_attr_type;
 
-	if (!(cache_validity & NFS_INO_INVALID_CHANGE) &&
+	if (ctype != NFS4_CHANGE_TYPE_IS_UNDEFINED &&
+	    !(cache_validity & NFS_INO_INVALID_CHANGE) &&
 	    (cache_validity & check_valid) != 0 &&
 	    (fattr->valid & NFS_ATTR_FATTR_CHANGE) != 0 &&
 	    nfs_inode_attrs_cmp_monotonic(fattr, inode) == 0)
@@ -1786,6 +1838,66 @@
 	return 0;
 }
 
+static void nfs_ooo_merge(struct nfs_inode *nfsi,
+			  u64 start, u64 end)
+{
+	int i, cnt;
+
+	if (nfsi->cache_validity & NFS_INO_DATA_INVAL_DEFER)
+		/* No point merging anything */
+		return;
+
+	if (!nfsi->ooo) {
+		nfsi->ooo = kmalloc(sizeof(*nfsi->ooo), GFP_ATOMIC);
+		if (!nfsi->ooo) {
+			nfsi->cache_validity |= NFS_INO_DATA_INVAL_DEFER;
+			return;
+		}
+		nfsi->ooo->cnt = 0;
+	}
+
+	/* add this range, merging if possible */
+	cnt = nfsi->ooo->cnt;
+	for (i = 0; i < cnt; i++) {
+		if (end == nfsi->ooo->gap[i].start)
+			end = nfsi->ooo->gap[i].end;
+		else if (start == nfsi->ooo->gap[i].end)
+			start = nfsi->ooo->gap[i].start;
+		else
+			continue;
+		/* Remove 'i' from table and loop to insert the new range */
+		cnt -= 1;
+		nfsi->ooo->gap[i] = nfsi->ooo->gap[cnt];
+		i = -1;
+	}
+	if (start != end) {
+		if (cnt >= ARRAY_SIZE(nfsi->ooo->gap)) {
+			nfsi->cache_validity |= NFS_INO_DATA_INVAL_DEFER;
+			kfree(nfsi->ooo);
+			nfsi->ooo = NULL;
+			return;
+		}
+		nfsi->ooo->gap[cnt].start = start;
+		nfsi->ooo->gap[cnt].end = end;
+		cnt += 1;
+	}
+	nfsi->ooo->cnt = cnt;
+}
+
+static void nfs_ooo_record(struct nfs_inode *nfsi,
+			   struct nfs_fattr *fattr)
+{
+	/* This reply was out-of-order, so record in the
+	 * pre/post change id, possibly cancelling
+	 * gaps created when iversion was jumpped forward.
+	 */
+	if ((fattr->valid & NFS_ATTR_FATTR_CHANGE) &&
+	    (fattr->valid & NFS_ATTR_FATTR_PRECHANGE))
+		nfs_ooo_merge(nfsi,
+			      fattr->change_attr,
+			      fattr->pre_change_attr);
+}
+
 static int nfs_refresh_inode_locked(struct inode *inode,
 				    struct nfs_fattr *fattr)
 {
@@ -1796,8 +1908,12 @@
 
 	if (attr_cmp > 0 || nfs_inode_finish_partial_attr_update(fattr, inode))
 		ret = nfs_update_inode(inode, fattr);
-	else if (attr_cmp == 0)
-		ret = nfs_check_inode_attributes(inode, fattr);
+	else {
+		nfs_ooo_record(NFS_I(inode), fattr);
+
+		if (attr_cmp == 0)
+			ret = nfs_check_inode_attributes(inode, fattr);
+	}
 
 	trace_nfs_refresh_inode_exit(inode, ret);
 	return ret;
@@ -1888,6 +2004,8 @@
 	if (attr_cmp < 0)
 		return 0;
 	if ((fattr->valid & NFS_ATTR_FATTR) == 0 || !attr_cmp) {
+		/* Record the pre/post change info before clearing PRECHANGE */
+		nfs_ooo_record(NFS_I(inode), fattr);
 		fattr->valid &= ~(NFS_ATTR_FATTR_PRECHANGE
 				| NFS_ATTR_FATTR_PRESIZE
 				| NFS_ATTR_FATTR_PREMTIME
@@ -2042,6 +2160,15 @@
 
 	/* More cache consistency checks */
 	if (fattr->valid & NFS_ATTR_FATTR_CHANGE) {
+		if (!have_writers && nfsi->ooo && nfsi->ooo->cnt == 1 &&
+		    nfsi->ooo->gap[0].end == inode_peek_iversion_raw(inode)) {
+			/* There is one remaining gap that hasn't been
+			 * merged into iversion - do that now.
+			 */
+			inode_set_iversion_raw(inode, nfsi->ooo->gap[0].start);
+			kfree(nfsi->ooo);
+			nfsi->ooo = NULL;
+		}
 		if (!inode_eq_iversion_raw(inode, fattr->change_attr)) {
 			/* Could it be a race with writeback? */
 			if (!(have_writers || have_delegation)) {
@@ -2063,8 +2190,11 @@
 				dprintk("NFS: change_attr change on server for file %s/%ld\n",
 						inode->i_sb->s_id,
 						inode->i_ino);
-			} else if (!have_delegation)
-				nfsi->cache_validity |= NFS_INO_DATA_INVAL_DEFER;
+			} else if (!have_delegation) {
+				nfs_ooo_record(nfsi, fattr);
+				nfs_ooo_merge(nfsi, inode_peek_iversion_raw(inode),
+					      fattr->change_attr);
+			}
 			inode_set_iversion_raw(inode, fattr->change_attr);
 		}
 	} else {
@@ -2226,6 +2356,7 @@
 		return NULL;
 	nfsi->flags = 0UL;
 	nfsi->cache_validity = 0UL;
+	nfsi->ooo = NULL;
 #if IS_ENABLED(CONFIG_NFS_V4)
 	nfsi->nfs4_acl = NULL;
 #endif /* CONFIG_NFS_V4 */
@@ -2238,6 +2369,7 @@
 
 void nfs_free_inode(struct inode *inode)
 {
+	kfree(NFS_I(inode)->ooo);
 	kmem_cache_free(nfs_inode_cachep, NFS_I(inode));
 }
 EXPORT_SYMBOL_GPL(nfs_free_inode);
@@ -2260,14 +2392,7 @@
 	INIT_LIST_HEAD(&nfsi->open_files);
 	INIT_LIST_HEAD(&nfsi->access_cache_entry_lru);
 	INIT_LIST_HEAD(&nfsi->access_cache_inode_lru);
-	INIT_LIST_HEAD(&nfsi->commit_info.list);
-	atomic_long_set(&nfsi->nrequests, 0);
-	atomic_long_set(&nfsi->commit_info.ncommit, 0);
-	atomic_set(&nfsi->commit_info.rpcs_out, 0);
-	init_rwsem(&nfsi->rmdir_sem);
-	mutex_init(&nfsi->commit_mutex);
 	nfs4_init_once(nfsi);
-	nfsi->cache_change_attribute = 0;
 }
 
 static int __init nfs_init_inodecache(void)
@@ -2329,12 +2454,21 @@
 
 static int nfs_net_init(struct net *net)
 {
+	struct nfs_net *nn = net_generic(net, nfs_net_id);
+
 	nfs_clients_init(net);
+
+	if (!rpc_proc_register(net, &nn->rpcstats)) {
+		nfs_clients_exit(net);
+		return -ENOMEM;
+	}
+
 	return nfs_fs_proc_net_init(net);
 }
 
 static void nfs_net_exit(struct net *net)
 {
+	rpc_proc_unregister(net, "nfs");
 	nfs_fs_proc_net_exit(net);
 	nfs_clients_exit(net);
 }
@@ -2393,15 +2527,12 @@
 	if (err)
 		goto out1;
 
-	rpc_proc_register(&init_net, &nfs_rpcstat);
-
 	err = register_nfs_fs();
 	if (err)
 		goto out0;
 
 	return 0;
 out0:
-	rpc_proc_unregister(&init_net, "nfs");
 	nfs_destroy_directcache();
 out1:
 	nfs_destroy_writepagecache();
@@ -2434,7 +2565,6 @@
 	nfs_destroy_nfspagecache();
 	nfs_fscache_unregister();
 	unregister_pernet_subsys(&nfs_net_ops);
-	rpc_proc_unregister(&init_net, "nfs");
 	unregister_nfs_fs();
 	nfs_fs_proc_exit();
 	nfsiod_stop();
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/internal.h
@@ -11,7 +11,7 @@
 #include <linux/nfs_page.h>
 #include <linux/wait_bit.h>
 
-#define NFS_SB_MASK (SB_RDONLY|SB_NOSUID|SB_NODEV|SB_NOEXEC|SB_SYNCHRONOUS)
+#define NFS_SB_MASK (SB_NOSUID|SB_NODEV|SB_NOEXEC|SB_SYNCHRONOUS)
 
 extern const struct export_operations nfs_export_ops;
 
@@ -42,6 +42,16 @@
 	return true;
 }
 
+static inline fmode_t flags_to_mode(int flags)
+{
+	fmode_t res = (__force fmode_t)flags & FMODE_EXEC;
+	if ((flags & O_ACCMODE) != O_WRONLY)
+		res |= FMODE_READ;
+	if ((flags & O_ACCMODE) != O_RDONLY)
+		res |= FMODE_WRITE;
+	return res;
+}
+
 /*
  * Note: RFC 1813 doesn't limit the number of auth flavors that
  * a server can return, so make something up.
@@ -341,14 +351,6 @@
 
 	return dst;
 }
-static inline void nfs4_label_free(struct nfs4_label *label)
-{
-	if (label) {
-		kfree(label->label);
-		kfree(label);
-	}
-	return;
-}
 
 static inline void nfs_zap_label_cache_locked(struct nfs_inode *nfsi)
 {
@@ -357,7 +359,6 @@
 }
 #else
 static inline struct nfs4_label *nfs4_label_alloc(struct nfs_server *server, gfp_t flags) { return NULL; }
-static inline void nfs4_label_free(void *label) {}
 static inline void nfs_zap_label_cache_locked(struct nfs_inode *nfsi)
 {
 }
@@ -427,8 +428,6 @@
 int nfs_get_tree_common(struct fs_context *);
 void nfs_kill_super(struct super_block *);
 
-extern struct rpc_stat nfs_rpcstat;
-
 extern int __init register_nfs_fs(void);
 extern void __exit unregister_nfs_fs(void);
 extern bool nfs_sb_active(struct super_block *sb);
@@ -580,6 +579,13 @@
 		!nfs_write_verifier_cmp(&req->wb_verf, &verf->verifier);
 }
 
+static inline gfp_t nfs_io_gfp_mask(void)
+{
+	if (current->flags & PF_WQ_WORKER)
+		return GFP_KERNEL | __GFP_NORETRY | __GFP_NOWARN;
+	return GFP_KERNEL;
+}
+
 /* unlink.c */
 extern struct rpc_task *
 nfs_async_rename(struct inode *old_dir, struct inode *new_dir,
@@ -647,9 +653,9 @@
 	if ((bsize & (bsize - 1)) || nrbitsp) {
 		unsigned char	nrbits;
 
-		for (nrbits = 31; nrbits && !(bsize & (1 << nrbits)); nrbits--)
+		for (nrbits = 31; nrbits && !(bsize & (1UL << nrbits)); nrbits--)
 			;
-		bsize = 1 << nrbits;
+		bsize = 1UL << nrbits;
 		if (nrbitsp)
 			*nrbitsp = nrbits;
 	}
@@ -817,6 +823,7 @@
 	case 0:
 	case -ERESTARTSYS:
 	case -EINTR:
+	case -ENOMEM:
 		return false;
 	}
 	return nfs_error_is_fatal(err);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/namespace.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/namespace.c
@@ -147,7 +147,7 @@
 	struct nfs_fs_context *ctx;
 	struct fs_context *fc;
 	struct vfsmount *mnt = ERR_PTR(-ENOMEM);
-	struct nfs_server *server = NFS_SERVER(d_inode(path->dentry));
+	struct nfs_server *server = NFS_SB(path->dentry->d_sb);
 	struct nfs_client *client = server->nfs_client;
 	int timeout = READ_ONCE(nfs_mountpoint_expiry_timeout);
 	int ret;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/netns.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/netns.h
@@ -9,6 +9,7 @@
 #include <linux/nfs4.h>
 #include <net/net_namespace.h>
 #include <net/netns/generic.h>
+#include <linux/sunrpc/stats.h>
 
 struct bl_dev_msg {
 	int32_t status;
@@ -34,6 +35,7 @@
 	struct nfs_netns_client *nfs_client;
 	spinlock_t nfs_client_lock;
 	ktime_t boot_time;
+	struct rpc_stat rpcstats;
 #ifdef CONFIG_PROC_FS
 	struct proc_dir_entry *proc_nfsfs;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs2xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs2xdr.c
@@ -949,7 +949,7 @@
 
 	error = decode_filename_inline(xdr, &entry->name, &entry->len);
 	if (unlikely(error))
-		return error;
+		return error == -ENAMETOOLONG ? -ENAMETOOLONG : -EAGAIN;
 
 	/*
 	 * The type (size and byte order) of nfscookie isn't defined in
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs3client.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs3client.c
@@ -108,7 +108,6 @@
 	if (mds_srv->flags & NFS_MOUNT_NORESVPORT)
 		__set_bit(NFS_CS_NORESVPORT, &cl_init.init_flags);
 
-	__set_bit(NFS_CS_NOPING, &cl_init.init_flags);
 	__set_bit(NFS_CS_DS, &cl_init.init_flags);
 
 	/* Use the MDS nfs_client cl_ipaddr. */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs3xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs3xdr.c
@@ -1967,7 +1967,6 @@
 		       bool plus)
 {
 	struct user_namespace *userns = rpc_userns(entry->server->client);
-	struct nfs_entry old = *entry;
 	__be32 *p;
 	int error;
 	u64 new_cookie;
@@ -1987,15 +1986,15 @@
 
 	error = decode_fileid3(xdr, &entry->ino);
 	if (unlikely(error))
-		return error;
+		return -EAGAIN;
 
 	error = decode_inline_filename3(xdr, &entry->name, &entry->len);
 	if (unlikely(error))
-		return error;
+		return error == -ENAMETOOLONG ? -ENAMETOOLONG : -EAGAIN;
 
 	error = decode_cookie3(xdr, &new_cookie);
 	if (unlikely(error))
-		return error;
+		return -EAGAIN;
 
 	entry->d_type = DT_UNKNOWN;
 
@@ -2003,7 +2002,7 @@
 		entry->fattr->valid = 0;
 		error = decode_post_op_attr(xdr, entry->fattr, userns);
 		if (unlikely(error))
-			return error;
+			return -EAGAIN;
 		if (entry->fattr->valid & NFS_ATTR_FATTR_V3)
 			entry->d_type = nfs_umode_to_dtype(entry->fattr->mode);
 
@@ -2018,11 +2017,8 @@
 			return -EAGAIN;
 		if (*p != xdr_zero) {
 			error = decode_nfs_fh3(xdr, entry->fh);
-			if (unlikely(error)) {
-				if (error == -E2BIG)
-					goto out_truncated;
-				return error;
-			}
+			if (unlikely(error))
+				return -EAGAIN;
 		} else
 			zero_nfs_fh3(entry->fh);
 	}
@@ -2031,11 +2027,6 @@
 	entry->cookie = new_cookie;
 
 	return 0;
-
-out_truncated:
-	dprintk("NFS: directory entry contains invalid file handle\n");
-	*entry = old;
-	return -EAGAIN;
 }
 
 /*
@@ -2227,7 +2218,8 @@
 
 	/* ignore properties */
 	result->lease_time = 0;
-	result->change_attr_type = NFS4_CHANGE_TYPE_IS_TIME_METADATA;
+	result->change_attr_type = NFS4_CHANGE_TYPE_IS_UNDEFINED;
+	result->xattr_support = 0;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs42.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs42.h
@@ -54,11 +54,14 @@
  * They would be 7 bytes long in the eventual buffer ("user.x\0"), and
  * 8 bytes long XDR-encoded.
  *
- * Include the trailing eof word as well.
+ * Include the trailing eof word as well and make the result a multiple
+ * of 4 bytes.
  */
 static inline u32 nfs42_listxattr_xdrsize(u32 buflen)
 {
-	return ((buflen / (XATTR_USER_PREFIX_LEN + 2)) * 8) + 4;
+	u32 size = 8 * buflen / (XATTR_USER_PREFIX_LEN + 2) + 4;
+
+	return (size + 3) & ~3;
 }
 #endif /* CONFIG_NFS_V4_2 */
 #endif /* __LINUX_FS_NFS_NFS4_2_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs42proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs42proc.c
@@ -210,7 +210,7 @@
 
 	if (dst_server != src_server) {
 		spin_lock(&src_server->nfs_client->cl_lock);
-		list_add_tail(&copy->src_copies, &src_server->ss_copies);
+		list_add_tail(&copy->src_copies, &src_server->ss_src_copies);
 		spin_unlock(&src_server->nfs_client->cl_lock);
 	}
 
@@ -285,7 +285,9 @@
 	loff_t newsize = pos + len;
 	loff_t end = newsize - 1;
 
-	truncate_pagecache_range(inode, pos, end);
+	WARN_ON_ONCE(invalidate_inode_pages2_range(inode->i_mapping,
+				pos >> PAGE_SHIFT, end >> PAGE_SHIFT));
+
 	spin_lock(&inode->i_lock);
 	if (newsize > i_size_read(inode))
 		i_size_write(inode, newsize);
@@ -460,8 +462,9 @@
 				continue;
 			}
 			break;
-		} else if (err == -NFS4ERR_OFFLOAD_NO_REQS && !args.sync) {
-			args.sync = true;
+		} else if (err == -NFS4ERR_OFFLOAD_NO_REQS &&
+				args.sync != res.synchronous) {
+			args.sync = res.synchronous;
 			dst_exception.retry = 1;
 			continue;
 		} else if ((err == -ESTALE ||
@@ -538,7 +541,7 @@
 		.rpc_message = &msg,
 		.callback_ops = &nfs42_offload_cancel_ops,
 		.workqueue = nfsiod_workqueue,
-		.flags = RPC_TASK_ASYNC,
+		.flags = RPC_TASK_ASYNC | RPC_TASK_MOVEABLE,
 	};
 	int status;
 
@@ -584,8 +587,10 @@
 
 	ctx = get_nfs_open_context(nfs_file_open_context(src));
 	l_ctx = nfs_get_lock_context(ctx);
-	if (IS_ERR(l_ctx))
-		return PTR_ERR(l_ctx);
+	if (IS_ERR(l_ctx)) {
+		status = PTR_ERR(l_ctx);
+		goto out;
+	}
 
 	status = nfs4_set_rw_stateid(&args->cna_src_stateid, ctx, l_ctx,
 				     FMODE_READ);
@@ -593,7 +598,7 @@
 	if (status) {
 		if (status == -EAGAIN)
 			status = -NFS4ERR_BAD_STATEID;
-		return status;
+		goto out;
 	}
 
 	status = nfs4_call_sync(src_server->client, src_server, &msg,
@@ -601,6 +606,7 @@
 	if (status == -ENOTSUPP)
 		src_server->caps &= ~NFS_CAP_COPY_NOTIFY;
 
+out:
 	put_nfs_open_context(nfs_file_open_context(src));
 	return status;
 }
@@ -1072,6 +1078,9 @@
 	status = nfs4_call_sync(server->client, server, msg,
 				&args.seq_args, &res.seq_res, 0);
 	if (status == 0) {
+		/* a zero-length count means clone to EOF in src */
+		if (count == 0 && res.dst_fattr->valid & NFS_ATTR_FATTR_SIZE)
+			count = nfs_size_to_loff_t(res.dst_fattr->size) - dst_offset;
 		nfs42_copy_dest_done(dst_inode, dst_offset, count);
 		status = nfs_post_op_update_inode(dst_inode, res.dst_fattr);
 	}
@@ -1331,7 +1340,6 @@
 	for (i = 0; i < np; i++) {
 		pages[i] = alloc_page(GFP_KERNEL);
 		if (!pages[i]) {
-			np = i + 1;
 			err = -ENOMEM;
 			goto out;
 		}
@@ -1355,8 +1363,8 @@
 	} while (exception.retry);
 
 out:
-	while (--np >= 0)
-		__free_page(pages[np]);
+	while (--i >= 0)
+		__free_page(pages[i]);
 	kfree(pages);
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs42xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs42xdr.c
@@ -122,9 +122,11 @@
 					 decode_putfh_maxsz + \
 					 decode_offload_cancel_maxsz)
 #define NFS4_enc_copy_notify_sz		(compound_encode_hdr_maxsz + \
+					 encode_sequence_maxsz + \
 					 encode_putfh_maxsz + \
 					 encode_copy_notify_maxsz)
 #define NFS4_dec_copy_notify_sz		(compound_decode_hdr_maxsz + \
+					 decode_sequence_maxsz + \
 					 decode_putfh_maxsz + \
 					 decode_copy_notify_maxsz)
 #define NFS4_enc_deallocate_sz		(compound_encode_hdr_maxsz + \
@@ -1434,8 +1436,7 @@
 	status = decode_clone(xdr);
 	if (status)
 		goto out;
-	status = decode_getfattr(xdr, res->dst_fattr, res->server);
-
+	decode_getfattr(xdr, res->dst_fattr, res->server);
 out:
 	res->rpc_status = status;
 	return status;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4_fs.h
@@ -42,6 +42,7 @@
 	NFS4CLNT_LEASE_MOVED,
 	NFS4CLNT_DELEGATION_EXPIRED,
 	NFS4CLNT_RUN_MANAGER,
+	NFS4CLNT_MANAGER_AVAILABLE,
 	NFS4CLNT_RECALL_RUNNING,
 	NFS4CLNT_RECALL_ANY_LAYOUT_READ,
 	NFS4CLNT_RECALL_ANY_LAYOUT_RW,
@@ -261,8 +262,8 @@
 };
 
 struct nfs4_mig_recovery_ops {
-	int (*get_locations)(struct inode *, struct nfs4_fs_locations *,
-		struct page *, const struct cred *);
+	int (*get_locations)(struct nfs_server *, struct nfs_fh *,
+		struct nfs4_fs_locations *, struct page *, const struct cred *);
 	int (*fsid_present)(struct inode *, const struct cred *);
 };
 
@@ -281,7 +282,8 @@
 int nfs4_submount(struct fs_context *, struct nfs_server *);
 int nfs4_replace_transport(struct nfs_server *server,
 				const struct nfs4_fs_locations *locations);
-
+size_t nfs_parse_server_name(char *string, size_t len, struct sockaddr *sa,
+			     size_t salen, struct net *net, int port);
 /* nfs4proc.c */
 extern int nfs4_handle_exception(struct nfs_server *, int, struct nfs4_exception *);
 extern int nfs4_async_handle_error(struct rpc_task *task,
@@ -303,8 +305,9 @@
 extern int nfs4_server_capabilities(struct nfs_server *server, struct nfs_fh *fhandle);
 extern int nfs4_proc_fs_locations(struct rpc_clnt *, struct inode *, const struct qstr *,
 				  struct nfs4_fs_locations *, struct page *);
-extern int nfs4_proc_get_locations(struct inode *, struct nfs4_fs_locations *,
-		struct page *page, const struct cred *);
+extern int nfs4_proc_get_locations(struct nfs_server *, struct nfs_fh *,
+				   struct nfs4_fs_locations *,
+				   struct page *page, const struct cred *);
 extern int nfs4_proc_fsid_present(struct inode *, const struct cred *);
 extern struct rpc_clnt *nfs4_proc_lookup_mountpoint(struct inode *,
 						    struct dentry *,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4client.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4client.c
@@ -230,7 +230,8 @@
 		__set_bit(NFS_CS_INFINITE_SLOTS, &clp->cl_flags);
 	__set_bit(NFS_CS_DISCRTRY, &clp->cl_flags);
 	__set_bit(NFS_CS_NO_RETRANS_TIMEOUT, &clp->cl_flags);
-
+	if (test_bit(NFS_CS_PNFS, &cl_init->init_flags))
+		__set_bit(NFS_CS_PNFS, &clp->cl_flags);
 	/*
 	 * Set up the connection to the server before we add add to the
 	 * global list.
@@ -346,6 +347,7 @@
 	ret = nfs4_setup_slot_table(tbl, NFS4_MAX_SLOT_TABLE,
 					"NFSv4.0 transport Slot table");
 	if (ret) {
+		nfs4_shutdown_slot_table(tbl);
 		kfree(tbl);
 		return ret;
 	}
@@ -413,6 +415,8 @@
 		.net = old->cl_net,
 		.servername = old->cl_hostname,
 	};
+	int max_connect = test_bit(NFS_CS_PNFS, &clp->cl_flags) ?
+		clp->cl_max_connect : old->cl_max_connect;
 
 	if (clp->cl_proto != old->cl_proto)
 		return;
@@ -426,7 +430,7 @@
 	xprt_args.addrlen = clp_salen;
 
 	rpc_clnt_add_xprt(old->cl_rpcclient, &xprt_args,
-			  rpc_clnt_test_and_add_xprt, NULL);
+			  rpc_clnt_test_and_add_xprt, &max_connect);
 }
 
 /**
@@ -992,6 +996,8 @@
 	if (mds_srv->flags & NFS_MOUNT_NORESVPORT)
 		__set_bit(NFS_CS_NORESVPORT, &cl_init.init_flags);
 
+	__set_bit(NFS_CS_PNFS, &cl_init.init_flags);
+	cl_init.max_connect = NFS_MAX_TRANSPORTS;
 	/*
 	 * Set an authflavor equual to the MDS value. Use the MDS nfs_client
 	 * cl_ipaddr so as to use the same EXCHANGE_ID co_ownerid as the MDS
@@ -1368,8 +1374,11 @@
 	}
 	nfs_put_client(clp);
 
-	if (server->nfs_client->cl_hostname == NULL)
+	if (server->nfs_client->cl_hostname == NULL) {
 		server->nfs_client->cl_hostname = kstrdup(hostname, GFP_KERNEL);
+		if (server->nfs_client->cl_hostname == NULL)
+			return -ENOMEM;
+	}
 	nfs_server_insert_lists(server);
 
 	return nfs_probe_destination(server);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4file.c
@@ -32,6 +32,7 @@
 	struct dentry *parent = NULL;
 	struct inode *dir;
 	unsigned openflags = filp->f_flags;
+	fmode_t f_mode;
 	struct iattr attr;
 	int err;
 
@@ -50,8 +51,9 @@
 	if (err)
 		return err;
 
+	f_mode = filp->f_mode;
 	if ((openflags & O_ACCMODE) == 3)
-		return nfs_open(inode, filp);
+		f_mode |= flags_to_mode(openflags);
 
 	/* We can't create new files here */
 	openflags &= ~(O_CREAT|O_EXCL);
@@ -59,7 +61,7 @@
 	parent = dget_parent(dentry);
 	dir = d_inode(parent);
 
-	ctx = alloc_nfs_open_context(file_dentry(filp), filp->f_mode, filp);
+	ctx = alloc_nfs_open_context(file_dentry(filp), f_mode, filp);
 	err = PTR_ERR(ctx);
 	if (IS_ERR(ctx))
 		goto out;
@@ -317,7 +319,7 @@
 static struct file *__nfs42_ssc_open(struct vfsmount *ss_mnt,
 		struct nfs_fh *src_fh, nfs4_stateid *stateid)
 {
-	struct nfs_fattr fattr;
+	struct nfs_fattr *fattr = nfs_alloc_fattr();
 	struct file *filep, *res;
 	struct nfs_server *server;
 	struct inode *r_ino = NULL;
@@ -328,14 +330,20 @@
 
 	server = NFS_SERVER(ss_mnt->mnt_root->d_inode);
 
-	nfs_fattr_init(&fattr);
+	if (!fattr)
+		return ERR_PTR(-ENOMEM);
 
-	status = nfs4_proc_getattr(server, src_fh, &fattr, NULL, NULL);
+	status = nfs4_proc_getattr(server, src_fh, fattr, NULL, NULL);
 	if (status < 0) {
 		res = ERR_PTR(status);
 		goto out;
 	}
 
+	if (!S_ISREG(fattr->mode)) {
+		res = ERR_PTR(-EBADF);
+		goto out;
+	}
+
 	res = ERR_PTR(-ENOMEM);
 	len = strlen(SSC_READ_NAME_BODY) + 16;
 	read_name = kzalloc(len, GFP_NOFS);
@@ -343,7 +351,7 @@
 		goto out;
 	snprintf(read_name, len, SSC_READ_NAME_BODY, read_name_gen++);
 
-	r_ino = nfs_fhget(ss_mnt->mnt_root->d_inode->i_sb, src_fh, &fattr,
+	r_ino = nfs_fhget(ss_mnt->mnt_root->d_inode->i_sb, src_fh, fattr,
 			NULL);
 	if (IS_ERR(r_ino)) {
 		res = ERR_CAST(r_ino);
@@ -354,6 +362,7 @@
 				     r_ino->i_fop);
 	if (IS_ERR(filep)) {
 		res = ERR_CAST(filep);
+		iput(r_ino);
 		goto out_free_name;
 	}
 	filep->f_mode |= FMODE_READ;
@@ -388,6 +397,7 @@
 out_free_name:
 	kfree(read_name);
 out:
+	nfs_free_fattr(fattr);
 	return res;
 out_stateowner:
 	nfs4_put_state_owner(sp);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4idmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4idmap.c
@@ -487,7 +487,7 @@
 err_destroy_pipe:
 	rpc_destroy_pipe_data(idmap->idmap_pipe);
 err:
-	get_user_ns(idmap->user_ns);
+	put_user_ns(idmap->user_ns);
 	kfree(idmap);
 	return error;
 }
@@ -561,22 +561,20 @@
 	return true;
 }
 
-static void
-nfs_idmap_complete_pipe_upcall_locked(struct idmap *idmap, int ret)
+static void nfs_idmap_complete_pipe_upcall(struct idmap_legacy_upcalldata *data,
+					   int ret)
 {
-	struct key *authkey = idmap->idmap_upcall_data->authkey;
-
-	kfree(idmap->idmap_upcall_data);
-	idmap->idmap_upcall_data = NULL;
-	complete_request_key(authkey, ret);
-	key_put(authkey);
+	complete_request_key(data->authkey, ret);
+	key_put(data->authkey);
+	kfree(data);
 }
 
-static void
-nfs_idmap_abort_pipe_upcall(struct idmap *idmap, int ret)
+static void nfs_idmap_abort_pipe_upcall(struct idmap *idmap,
+					struct idmap_legacy_upcalldata *data,
+					int ret)
 {
-	if (idmap->idmap_upcall_data != NULL)
-		nfs_idmap_complete_pipe_upcall_locked(idmap, ret);
+	if (cmpxchg(&idmap->idmap_upcall_data, data, NULL) == data)
+		nfs_idmap_complete_pipe_upcall(data, ret);
 }
 
 static int nfs_idmap_legacy_upcall(struct key *authkey, void *aux)
@@ -613,7 +611,7 @@
 
 	ret = rpc_queue_upcall(idmap->idmap_pipe, msg);
 	if (ret < 0)
-		nfs_idmap_abort_pipe_upcall(idmap, ret);
+		nfs_idmap_abort_pipe_upcall(idmap, data, ret);
 
 	return ret;
 out2:
@@ -669,6 +667,7 @@
 	struct request_key_auth *rka;
 	struct rpc_inode *rpci = RPC_I(file_inode(filp));
 	struct idmap *idmap = (struct idmap *)rpci->private;
+	struct idmap_legacy_upcalldata *data;
 	struct key *authkey;
 	struct idmap_msg im;
 	size_t namelen_in;
@@ -678,10 +677,11 @@
 	 * will have been woken up and someone else may now have used
 	 * idmap_key_cons - so after this point we may no longer touch it.
 	 */
-	if (idmap->idmap_upcall_data == NULL)
+	data = xchg(&idmap->idmap_upcall_data, NULL);
+	if (data == NULL)
 		goto out_noupcall;
 
-	authkey = idmap->idmap_upcall_data->authkey;
+	authkey = data->authkey;
 	rka = get_request_key_auth(authkey);
 
 	if (mlen != sizeof(im)) {
@@ -703,18 +703,17 @@
 	if (namelen_in == 0 || namelen_in == IDMAP_NAMESZ) {
 		ret = -EINVAL;
 		goto out;
-}
+	}
 
-	ret = nfs_idmap_read_and_verify_message(&im,
-			&idmap->idmap_upcall_data->idmap_msg,
-			rka->target_key, authkey);
+	ret = nfs_idmap_read_and_verify_message(&im, &data->idmap_msg,
+						rka->target_key, authkey);
 	if (ret >= 0) {
 		key_set_timeout(rka->target_key, nfs_idmap_cache_timeout);
 		ret = mlen;
 	}
 
 out:
-	nfs_idmap_complete_pipe_upcall_locked(idmap, ret);
+	nfs_idmap_complete_pipe_upcall(data, ret);
 out_noupcall:
 	return ret;
 }
@@ -728,7 +727,7 @@
 	struct idmap *idmap = data->idmap;
 
 	if (msg->errno)
-		nfs_idmap_abort_pipe_upcall(idmap, msg->errno);
+		nfs_idmap_abort_pipe_upcall(idmap, data, msg->errno);
 }
 
 static void
@@ -736,8 +735,11 @@
 {
 	struct rpc_inode *rpci = RPC_I(inode);
 	struct idmap *idmap = (struct idmap *)rpci->private;
+	struct idmap_legacy_upcalldata *data;
 
-	nfs_idmap_abort_pipe_upcall(idmap, -EPIPE);
+	data = xchg(&idmap->idmap_upcall_data, NULL);
+	if (data)
+		nfs_idmap_complete_pipe_upcall(data, -EPIPE);
 }
 
 int nfs_map_name_to_uid(const struct nfs_server *server, const char *name, size_t namelen, kuid_t *uid)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4namespace.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4namespace.c
@@ -164,16 +164,21 @@
 	return 0;
 }
 
-static size_t nfs_parse_server_name(char *string, size_t len,
-		struct sockaddr *sa, size_t salen, struct net *net)
+size_t nfs_parse_server_name(char *string, size_t len, struct sockaddr *sa,
+			     size_t salen, struct net *net, int port)
 {
 	ssize_t ret;
 
 	ret = rpc_pton(net, string, len, sa, salen);
 	if (ret == 0) {
-		ret = nfs_dns_resolve_name(net, string, len, sa, salen);
-		if (ret < 0)
-			ret = 0;
+		ret = rpc_uaddr2sockaddr(net, string, len, sa, salen);
+		if (ret == 0) {
+			ret = nfs_dns_resolve_name(net, string, len, sa, salen);
+			if (ret < 0)
+				ret = 0;
+		}
+	} else if (port) {
+		rpc_set_port(sa, port);
 	}
 	return ret;
 }
@@ -328,7 +333,7 @@
 			nfs_parse_server_name(buf->data, buf->len,
 					      &ctx->nfs_server.address,
 					      sizeof(ctx->nfs_server._address),
-					      fc->net_ns);
+					      fc->net_ns, 0);
 		if (ctx->nfs_server.addrlen == 0)
 			continue;
 
@@ -412,6 +417,9 @@
 	fs_locations = kmalloc(sizeof(struct nfs4_fs_locations), GFP_KERNEL);
 	if (!fs_locations)
 		goto out_free;
+	fs_locations->fattr = nfs_alloc_fattr();
+	if (!fs_locations->fattr)
+		goto out_free_2;
 
 	/* Get locations */
 	dentry = ctx->clone_data.dentry;
@@ -422,14 +430,16 @@
 	err = nfs4_proc_fs_locations(client, d_inode(parent), &dentry->d_name, fs_locations, page);
 	dput(parent);
 	if (err != 0)
-		goto out_free_2;
+		goto out_free_3;
 
 	err = -ENOENT;
 	if (fs_locations->nlocations <= 0 ||
 	    fs_locations->fs_path.ncomponents <= 0)
-		goto out_free_2;
+		goto out_free_3;
 
 	err = nfs_follow_referral(fc, fs_locations);
+out_free_3:
+	kfree(fs_locations->fattr);
 out_free_2:
 	kfree(fs_locations);
 out_free:
@@ -496,7 +506,7 @@
 			continue;
 
 		salen = nfs_parse_server_name(buf->data, buf->len,
-						sap, addr_bufsize, net);
+						sap, addr_bufsize, net, 0);
 		if (salen == 0)
 			continue;
 		rpc_set_port(sap, NFS_PORT);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4proc.c
@@ -126,6 +126,11 @@
 	if (nfs_server_capable(dir, NFS_CAP_SECURITY_LABEL) == 0)
 		return NULL;
 
+	label->lfs = 0;
+	label->pi = 0;
+	label->len = 0;
+	label->label = NULL;
+
 	err = security_dentry_init_security(dentry, sattr->ia_mode,
 				&dentry->d_name, (void **)&label->label, &label->len);
 	if (err == 0)
@@ -136,8 +141,12 @@
 static inline void
 nfs4_label_release_security(struct nfs4_label *label)
 {
-	if (label)
-		security_release_secctx(label->label, label->len);
+	struct lsmcontext scaff; /* scaffolding */
+
+	if (label) {
+		lsmcontext_init(&scaff, label->label, label->len, 0);
+		security_release_secctx(&scaff);
+	}
 }
 static inline u32 *nfs4_bitmask(struct nfs_server *server, struct nfs4_label *label)
 {
@@ -168,6 +177,7 @@
 	case -NFS4ERR_RESOURCE:
 	case -NFS4ERR_LAYOUTTRYLATER:
 	case -NFS4ERR_RECALLCONFLICT:
+	case -NFS4ERR_RETURNCONFLICT:
 		return -EREMOTEIO;
 	case -NFS4ERR_WRONGSEC:
 	case -NFS4ERR_WRONG_CRED:
@@ -366,6 +376,14 @@
 	kunmap_atomic(start);
 }
 
+static void nfs4_fattr_set_prechange(struct nfs_fattr *fattr, u64 version)
+{
+	if (!(fattr->valid & NFS_ATTR_FATTR_PRECHANGE)) {
+		fattr->pre_change_attr = version;
+		fattr->valid |= NFS_ATTR_FATTR_PRECHANGE;
+	}
+}
+
 static void nfs4_test_and_free_stateid(struct nfs_server *server,
 		nfs4_stateid *stateid,
 		const struct cred *cred)
@@ -547,6 +565,7 @@
 		case -NFS4ERR_GRACE:
 		case -NFS4ERR_LAYOUTTRYLATER:
 		case -NFS4ERR_RECALLCONFLICT:
+		case -NFS4ERR_RETURNCONFLICT:
 			exception->delay = 1;
 			return 0;
 
@@ -779,10 +798,9 @@
 	if ((s32)(seqnr - slot->seq_nr_highest_sent) > 0)
 		slot->seq_nr_highest_sent = seqnr;
 }
-static void nfs4_slot_sequence_acked(struct nfs4_slot *slot,
-		u32 seqnr)
+static void nfs4_slot_sequence_acked(struct nfs4_slot *slot, u32 seqnr)
 {
-	slot->seq_nr_highest_sent = seqnr;
+	nfs4_slot_sequence_record_sent(slot, seqnr);
 	slot->seq_nr_last_acked = seqnr;
 }
 
@@ -849,7 +867,6 @@
 			__func__,
 			slot->slot_nr,
 			slot->seq_nr);
-		nfs4_slot_sequence_acked(slot, slot->seq_nr);
 		goto out_retry;
 	case -NFS4ERR_RETRY_UNCACHED_REP:
 	case -NFS4ERR_SEQ_FALSE_RETRY:
@@ -912,6 +929,7 @@
 out_noaction:
 	return ret;
 session_recover:
+	set_bit(NFS4_SLOT_TBL_DRAINING, &session->fc_slot_table.slot_tbl_state);
 	nfs4_schedule_session_recovery(session, status);
 	dprintk("%s ERROR: %d Reset session\n", __func__, status);
 	nfs41_sequence_free_slot(res);
@@ -1157,7 +1175,7 @@
 {
 	unsigned short task_flags = 0;
 
-	if (server->nfs_client->cl_minorversion)
+	if (server->caps & NFS_CAP_MOVEABLE)
 		task_flags = RPC_TASK_MOVEABLE;
 	return nfs4_do_call_sync(clnt, server, msg, args, res, task_flags);
 }
@@ -1232,8 +1250,7 @@
 				NFS_INO_INVALID_ACCESS | NFS_INO_INVALID_ACL |
 				NFS_INO_INVALID_SIZE | NFS_INO_INVALID_OTHER |
 				NFS_INO_INVALID_BLOCKS | NFS_INO_INVALID_NLINK |
-				NFS_INO_INVALID_MODE | NFS_INO_INVALID_XATTR |
-				NFS_INO_REVAL_PAGECACHE;
+				NFS_INO_INVALID_MODE | NFS_INO_INVALID_XATTR;
 		nfsi->attrtimeo = NFS_MINATTRTIMEO(inode);
 	}
 	nfsi->attrtimeo_timestamp = jiffies;
@@ -1609,15 +1626,16 @@
 {
 	if (test_bit(NFS_OPEN_STATE, &state->flags)) {
 		/* The common case - we're updating to a new sequence number */
-		if (nfs4_stateid_match_other(stateid, &state->open_stateid) &&
-			nfs4_stateid_is_next(&state->open_stateid, stateid)) {
-			return true;
+		if (nfs4_stateid_match_other(stateid, &state->open_stateid)) {
+			if (nfs4_stateid_is_next(&state->open_stateid, stateid))
+				return true;
+			return false;
 		}
-	} else {
-		/* This is the first OPEN in this generation */
-		if (stateid->seqid == cpu_to_be32(1))
-			return true;
+		/* The server returned a new stateid */
 	}
+	/* This is the first OPEN in this generation */
+	if (stateid->seqid == cpu_to_be32(1))
+		return true;
 	return false;
 }
 
@@ -1982,8 +2000,7 @@
 	if (!data->rpc_done) {
 		if (data->rpc_status)
 			return ERR_PTR(data->rpc_status);
-		/* cached opens have already been processed */
-		goto update;
+		return nfs4_try_open_cached(data);
 	}
 
 	ret = nfs_refresh_inode(inode, &data->f_attr);
@@ -1992,7 +2009,7 @@
 
 	if (data->o_res.delegation_type != 0)
 		nfs4_opendata_check_deleg(data, state);
-update:
+
 	if (!update_open_stateid(state, &data->o_res.stateid,
 				NULL, data->o_arg.fmode))
 		return ERR_PTR(-EAGAIN);
@@ -2133,18 +2150,18 @@
 }
 
 static int nfs4_open_recover_helper(struct nfs4_opendata *opendata,
-		fmode_t fmode)
+				    fmode_t fmode)
 {
 	struct nfs4_state *newstate;
+	struct nfs_server *server = NFS_SB(opendata->dentry->d_sb);
+	int openflags = opendata->o_arg.open_flags;
 	int ret;
 
 	if (!nfs4_mode_match_open_stateid(opendata->state, fmode))
 		return 0;
-	opendata->o_arg.open_flags = 0;
 	opendata->o_arg.fmode = fmode;
-	opendata->o_arg.share_access = nfs4_map_atomic_open_share(
-			NFS_SB(opendata->dentry->d_sb),
-			fmode, 0);
+	opendata->o_arg.share_access =
+		nfs4_map_atomic_open_share(server, fmode, openflags);
 	memset(&opendata->o_res, 0, sizeof(opendata->o_res));
 	memset(&opendata->c_res, 0, sizeof(opendata->c_res));
 	nfs4_init_opendata_res(opendata);
@@ -2524,12 +2541,14 @@
 	struct nfs4_opendata *data = calldata;
 	struct nfs4_state *state = NULL;
 
+	/* In case of error, no cleanup! */
+	if (data->rpc_status != 0 || !data->rpc_done) {
+		nfs_release_seqid(data->o_arg.seqid);
+		goto out_free;
+	}
 	/* If this request hasn't been cancelled, do nothing */
 	if (!data->cancelled)
 		goto out_free;
-	/* In case of error, no cleanup! */
-	if (data->rpc_status != 0 || !data->rpc_done)
-		goto out_free;
 	/* In case we need an open_confirm, no cleanup! */
 	if (data->o_res.rflags & NFS4_OPEN_RESULT_CONFIRM)
 		goto out_free;
@@ -2570,7 +2589,7 @@
 	};
 	int status;
 
-	if (server->nfs_client->cl_minorversion)
+	if (nfs_server_capable(dir, NFS_CAP_MOVEABLE))
 		task_setup_data.flags |= RPC_TASK_MOVEABLE;
 
 	kref_get(&data->kref);
@@ -2724,10 +2743,15 @@
 	struct nfs4_opendata *opendata;
 	int ret;
 
-	opendata = nfs4_open_recoverdata_alloc(ctx, state,
-			NFS4_OPEN_CLAIM_FH);
+	opendata = nfs4_open_recoverdata_alloc(ctx, state, NFS4_OPEN_CLAIM_FH);
 	if (IS_ERR(opendata))
 		return PTR_ERR(opendata);
+	/*
+	 * We're not recovering a delegation, so ask for no delegation.
+	 * Otherwise the recovery thread could deadlock with an outstanding
+	 * delegation return.
+	 */
+	opendata->o_arg.open_flags = O_DIRECT;
 	ret = nfs4_open_recover(opendata, state);
 	if (ret == -ESTALE)
 		d_drop(ctx->dentry);
@@ -3100,8 +3124,13 @@
 	}
 
 out:
-	if (!opendata->cancelled)
+	if (!opendata->cancelled) {
+		if (opendata->lgp) {
+			nfs4_lgopen_release(opendata->lgp);
+			opendata->lgp = NULL;
+		}
 		nfs4_sequence_free_slot(&opendata->o_res.seq_res);
+	}
 	return ret;
 }
 
@@ -3753,7 +3782,7 @@
 	};
 	int status = -ENOMEM;
 
-	if (server->nfs_client->cl_minorversion)
+	if (nfs_server_capable(state->inode, NFS_CAP_MOVEABLE))
 		task_setup_data.flags |= RPC_TASK_MOVEABLE;
 
 	nfs4_state_protect(server->nfs_client, NFS_SP4_MACH_CRED_CLEANUP,
@@ -3812,7 +3841,7 @@
 		int open_flags, struct iattr *attr, int *opened)
 {
 	struct nfs4_state *state;
-	struct nfs4_label l = {0, 0, 0, NULL}, *label = NULL;
+	struct nfs4_label l, *label;
 
 	label = nfs4_label_init_security(dir, ctx->dentry, attr, &l);
 
@@ -3893,6 +3922,8 @@
 		if (res.attr_bitmask[2] & FATTR4_WORD2_SECURITY_LABEL)
 			server->caps |= NFS_CAP_SECURITY_LABEL;
 #endif
+		if (res.attr_bitmask[0] & FATTR4_WORD0_FS_LOCATIONS)
+			server->caps |= NFS_CAP_FS_LOCATIONS;
 		if (!(res.attr_bitmask[0] & FATTR4_WORD0_FILEID))
 			server->fattr_valid &= ~NFS_ATTR_FATTR_FILEID;
 		if (!(res.attr_bitmask[1] & FATTR4_WORD1_MODE))
@@ -3949,6 +3980,67 @@
 	return err;
 }
 
+static int _nfs4_discover_trunking(struct nfs_server *server,
+				   struct nfs_fh *fhandle)
+{
+	struct nfs4_fs_locations *locations = NULL;
+	struct page *page;
+	const struct cred *cred;
+	struct nfs_client *clp = server->nfs_client;
+	const struct nfs4_state_maintenance_ops *ops =
+		clp->cl_mvops->state_renewal_ops;
+	int status = -ENOMEM;
+
+	cred = ops->get_state_renewal_cred(clp);
+	if (cred == NULL) {
+		cred = nfs4_get_clid_cred(clp);
+		if (cred == NULL)
+			return -ENOKEY;
+	}
+
+	page = alloc_page(GFP_KERNEL);
+	if (!page)
+		goto out_put_cred;
+	locations = kmalloc(sizeof(struct nfs4_fs_locations), GFP_KERNEL);
+	if (!locations)
+		goto out_free;
+	locations->fattr = nfs_alloc_fattr();
+	if (!locations->fattr)
+		goto out_free_2;
+
+	status = nfs4_proc_get_locations(server, fhandle, locations, page,
+					 cred);
+
+	kfree(locations->fattr);
+out_free_2:
+	kfree(locations);
+out_free:
+	__free_page(page);
+out_put_cred:
+	put_cred(cred);
+	return status;
+}
+
+static int nfs4_discover_trunking(struct nfs_server *server,
+				  struct nfs_fh *fhandle)
+{
+	struct nfs4_exception exception = {
+		.interruptible = true,
+	};
+	struct nfs_client *clp = server->nfs_client;
+	int err = 0;
+
+	if (!nfs4_has_session(clp))
+		goto out;
+	do {
+		err = nfs4_handle_exception(server,
+				_nfs4_discover_trunking(server, fhandle),
+				&exception);
+	} while (exception.retry);
+out:
+	return err;
+}
+
 static int _nfs4_lookup_root(struct nfs_server *server, struct nfs_fh *fhandle,
 		struct nfs_fsinfo *info)
 {
@@ -4146,6 +4238,8 @@
 	if (locations == NULL)
 		goto out;
 
+	locations->fattr = fattr;
+
 	status = nfs4_proc_fs_locations(client, dir, name, locations, page);
 	if (status != 0)
 		goto out;
@@ -4155,17 +4249,14 @@
 	 * referral.  Cause us to drop into the exception handler, which
 	 * will kick off migration recovery.
 	 */
-	if (nfs_fsid_equal(&NFS_SERVER(dir)->fsid, &locations->fattr.fsid)) {
+	if (nfs_fsid_equal(&NFS_SERVER(dir)->fsid, &fattr->fsid)) {
 		dprintk("%s: server did not return a different fsid for"
 			" a referral at %s\n", __func__, name->name);
 		status = -NFS4ERR_MOVED;
 		goto out;
 	}
 	/* Fixup attributes for the nfs_lookup() call to nfs_fhget() */
-	nfs_fixup_referral_attributes(&locations->fattr);
-
-	/* replace the lookup nfs_fattr with the locations nfs_fattr */
-	memcpy(fattr, &locations->fattr, sizeof(struct nfs_fattr));
+	nfs_fixup_referral_attributes(fattr);
 	memset(fhandle, 0, sizeof(struct nfs_fh));
 out:
 	if (page)
@@ -4317,7 +4408,7 @@
 	};
 	unsigned short task_flags = 0;
 
-	if (server->nfs_client->cl_minorversion)
+	if (nfs_server_capable(dir, NFS_CAP_MOVEABLE))
 		task_flags = RPC_TASK_MOVEABLE;
 
 	/* Is this is an attribute revalidation, subject to softreval? */
@@ -4586,7 +4677,7 @@
 		 int flags)
 {
 	struct nfs_server *server = NFS_SERVER(dir);
-	struct nfs4_label l, *ilabel = NULL;
+	struct nfs4_label l, *ilabel;
 	struct nfs_open_context *ctx;
 	struct nfs4_state *state;
 	int status = 0;
@@ -4946,7 +5037,7 @@
 	struct nfs4_exception exception = {
 		.interruptible = true,
 	};
-	struct nfs4_label l, *label = NULL;
+	struct nfs4_label l, *label;
 	int err;
 
 	label = nfs4_label_init_security(dir, dentry, sattr, &l);
@@ -4987,7 +5078,7 @@
 	struct nfs4_exception exception = {
 		.interruptible = true,
 	};
-	struct nfs4_label l, *label = NULL;
+	struct nfs4_label l, *label;
 	int err;
 
 	label = nfs4_label_init_security(dir, dentry, sattr, &l);
@@ -5106,7 +5197,7 @@
 	struct nfs4_exception exception = {
 		.interruptible = true,
 	};
-	struct nfs4_label l, *label = NULL;
+	struct nfs4_label l, *label;
 	int err;
 
 	label = nfs4_label_init_security(dir, dentry, sattr, &l);
@@ -5336,7 +5427,7 @@
 	struct rpc_message *msg = &task->tk_msg;
 
 	if (msg->rpc_proc == &nfs4_procedures[NFSPROC4_CLNT_READ_PLUS] &&
-	    server->caps & NFS_CAP_READ_PLUS && task->tk_status == -ENOTSUPP) {
+	    task->tk_status == -ENOTSUPP) {
 		server->caps &= ~NFS_CAP_READ_PLUS;
 		msg->rpc_proc = &nfs4_procedures[NFSPROC4_CLNT_READ];
 		rpc_restart_call_prepare(task);
@@ -5525,7 +5616,7 @@
 
 	msg->rpc_proc = &nfs4_procedures[NFSPROC4_CLNT_WRITE];
 	nfs4_init_sequence(&hdr->args.seq_args, &hdr->res.seq_res, 0, 0);
-	nfs4_state_protect_write(server->nfs_client, clnt, msg, hdr);
+	nfs4_state_protect_write(hdr->ds_clp ? hdr->ds_clp : server->nfs_client, clnt, msg, hdr);
 }
 
 static void nfs4_proc_commit_rpc_prepare(struct rpc_task *task, struct nfs_commit_data *data)
@@ -5566,7 +5657,8 @@
 	data->res.server = server;
 	msg->rpc_proc = &nfs4_procedures[NFSPROC4_CLNT_COMMIT];
 	nfs4_init_sequence(&data->args.seq_args, &data->res.seq_res, 1, 0);
-	nfs4_state_protect(server->nfs_client, NFS_SP4_MACH_CRED_COMMIT, clnt, msg);
+	nfs4_state_protect(data->ds_clp ? data->ds_clp : server->nfs_client,
+			NFS_SP4_MACH_CRED_COMMIT, clnt, msg);
 }
 
 static int _nfs4_proc_commit(struct file *dst, struct nfs_commitargs *args,
@@ -5836,7 +5928,7 @@
 		buflen = server->rsize;
 
 	npages = DIV_ROUND_UP(buflen, PAGE_SIZE) + 1;
-	pages = kmalloc_array(npages, sizeof(struct page *), GFP_NOFS);
+	pages = kmalloc_array(npages, sizeof(struct page *), GFP_KERNEL);
 	if (!pages)
 		return -ENOMEM;
 
@@ -5881,9 +5973,8 @@
 out_ok:
 	ret = res.acl_len;
 out_free:
-	for (i = 0; i < npages; i++)
-		if (pages[i])
-			__free_page(pages[i]);
+	while (--i >= 0)
+		__free_page(pages[i]);
 	if (res.acl_scratch)
 		__free_page(res.acl_scratch);
 	kfree(pages);
@@ -6502,7 +6593,9 @@
 		pnfs_roc_release(&data->lr.arg, &data->lr.res,
 				 data->res.lr_ret);
 	if (inode) {
-		nfs_post_op_update_inode_force_wcc(inode, &data->fattr);
+		nfs4_fattr_set_prechange(&data->fattr,
+					 inode_peek_iversion_raw(inode));
+		nfs_refresh_inode(inode, &data->fattr);
 		nfs_iput_and_deactive(inode);
 	}
 	kfree(calldata);
@@ -6551,11 +6644,14 @@
 		.rpc_client = server->client,
 		.rpc_message = &msg,
 		.callback_ops = &nfs4_delegreturn_ops,
-		.flags = RPC_TASK_ASYNC | RPC_TASK_TIMEOUT | RPC_TASK_MOVEABLE,
+		.flags = RPC_TASK_ASYNC | RPC_TASK_TIMEOUT,
 	};
 	int status = 0;
 
-	data = kzalloc(sizeof(*data), GFP_NOFS);
+	if (nfs_server_capable(inode, NFS_CAP_MOVEABLE))
+		task_setup_data.flags |= RPC_TASK_MOVEABLE;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
 	if (data == NULL)
 		return -ENOMEM;
 
@@ -6744,7 +6840,7 @@
 	struct nfs4_state *state = lsp->ls_state;
 	struct inode *inode = state->inode;
 
-	p = kzalloc(sizeof(*p), GFP_NOFS);
+	p = kzalloc(sizeof(*p), GFP_KERNEL);
 	if (p == NULL)
 		return NULL;
 	p->arg.fh = NFS_FH(inode);
@@ -6869,10 +6965,8 @@
 		.workqueue = nfsiod_workqueue,
 		.flags = RPC_TASK_ASYNC,
 	};
-	struct nfs_client *client =
-		NFS_SERVER(lsp->ls_state->inode)->nfs_client;
 
-	if (client->cl_minorversion)
+	if (nfs_server_capable(lsp->ls_state->inode, NFS_CAP_MOVEABLE))
 		task_setup_data.flags |= RPC_TASK_MOVEABLE;
 
 	nfs4_state_protect(NFS_SERVER(lsp->ls_state->inode)->nfs_client,
@@ -7044,6 +7138,7 @@
 {
 	struct nfs4_lockdata *data = calldata;
 	struct nfs4_lock_state *lsp = data->lsp;
+	struct nfs_server *server = NFS_SERVER(d_inode(data->ctx->dentry));
 
 	dprintk("%s: begin!\n", __func__);
 
@@ -7053,8 +7148,7 @@
 	data->rpc_status = task->tk_status;
 	switch (task->tk_status) {
 	case 0:
-		renew_lease(NFS_SERVER(d_inode(data->ctx->dentry)),
-				data->timestamp);
+		renew_lease(server, data->timestamp);
 		if (data->arg.new_lock && !data->cancelled) {
 			data->fl.fl_flags &= ~(FL_SLEEP | FL_ACCESS);
 			if (locks_lock_inode_wait(lsp->ls_state->inode, &data->fl) < 0)
@@ -7067,14 +7161,23 @@
 		} else if (!nfs4_update_lock_stateid(lsp, &data->res.stateid))
 			goto out_restart;
 		break;
-	case -NFS4ERR_BAD_STATEID:
 	case -NFS4ERR_OLD_STATEID:
+		if (data->arg.new_lock_owner != 0 &&
+			nfs4_refresh_open_old_stateid(&data->arg.open_stateid,
+					lsp->ls_state))
+			goto out_restart;
+		if (nfs4_refresh_lock_old_stateid(&data->arg.lock_stateid, lsp))
+			goto out_restart;
+		fallthrough;
+	case -NFS4ERR_BAD_STATEID:
 	case -NFS4ERR_STALE_STATEID:
 	case -NFS4ERR_EXPIRED:
 		if (data->arg.new_lock_owner != 0) {
 			if (!nfs4_stateid_match(&data->arg.open_stateid,
 						&lsp->ls_state->open_stateid))
 				goto out_restart;
+			else if (nfs4_async_handle_error(task, server, lsp->ls_state, NULL) == -EAGAIN)
+				goto out_restart;
 		} else if (!nfs4_stateid_match(&data->arg.lock_stateid,
 						&lsp->ls_stateid))
 				goto out_restart;
@@ -7148,15 +7251,13 @@
 		.flags = RPC_TASK_ASYNC | RPC_TASK_CRED_NOREF,
 	};
 	int ret;
-	struct nfs_client *client = NFS_SERVER(state->inode)->nfs_client;
 
-	if (client->cl_minorversion)
+	if (nfs_server_capable(state->inode, NFS_CAP_MOVEABLE))
 		task_setup_data.flags |= RPC_TASK_MOVEABLE;
 
 	dprintk("%s: begin!\n", __func__);
 	data = nfs4_alloc_lockdata(fl, nfs_file_open_context(fl->fl_file),
-			fl->fl_u.nfs4_fl.owner,
-			recovery_type == NFS_LOCK_NEW ? GFP_KERNEL : GFP_NOFS);
+				   fl->fl_u.nfs4_fl.owner, GFP_KERNEL);
 	if (data == NULL)
 		return -ENOMEM;
 	if (IS_SETLKW(cmd))
@@ -7579,7 +7680,7 @@
 	if (server->nfs_client->cl_mvops->minor_version != 0)
 		return;
 
-	data = kmalloc(sizeof(*data), GFP_NOFS);
+	data = kmalloc(sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return;
 	data->lsp = lsp;
@@ -7676,7 +7777,7 @@
 				    const char *key, const void *buf,
 				    size_t buflen, int flags)
 {
-	struct nfs_access_entry cache;
+	u32 mask;
 	int ret;
 
 	if (!nfs_server_capable(inode, NFS_CAP_XATTR))
@@ -7691,8 +7792,8 @@
 	 * do a cached access check for the XA* flags to possibly avoid
 	 * doing an RPC and getting EACCES back.
 	 */
-	if (!nfs_access_get_cached(inode, current_cred(), &cache, true)) {
-		if (!(cache.mask & NFS_ACCESS_XAWRITE))
+	if (!nfs_access_get_cached(inode, current_cred(), &mask, true)) {
+		if (!(mask & NFS_ACCESS_XAWRITE))
 			return -EACCES;
 	}
 
@@ -7713,14 +7814,14 @@
 				    struct dentry *unused, struct inode *inode,
 				    const char *key, void *buf, size_t buflen)
 {
-	struct nfs_access_entry cache;
+	u32 mask;
 	ssize_t ret;
 
 	if (!nfs_server_capable(inode, NFS_CAP_XATTR))
 		return -EOPNOTSUPP;
 
-	if (!nfs_access_get_cached(inode, current_cred(), &cache, true)) {
-		if (!(cache.mask & NFS_ACCESS_XAREAD))
+	if (!nfs_access_get_cached(inode, current_cred(), &mask, true)) {
+		if (!(mask & NFS_ACCESS_XAREAD))
 			return -EACCES;
 	}
 
@@ -7745,13 +7846,13 @@
 	ssize_t ret, size;
 	char *buf;
 	size_t buflen;
-	struct nfs_access_entry cache;
+	u32 mask;
 
 	if (!nfs_server_capable(inode, NFS_CAP_XATTR))
 		return 0;
 
-	if (!nfs_access_get_cached(inode, current_cred(), &cache, true)) {
-		if (!(cache.mask & NFS_ACCESS_XALIST))
+	if (!nfs_access_get_cached(inode, current_cred(), &mask, true)) {
+		if (!(mask & NFS_ACCESS_XALIST))
 			return 0;
 	}
 
@@ -7849,7 +7950,7 @@
 	else
 		bitmask[1] &= ~FATTR4_WORD1_MOUNTED_ON_FILEID;
 
-	nfs_fattr_init(&fs_locations->fattr);
+	nfs_fattr_init(fs_locations->fattr);
 	fs_locations->server = server;
 	fs_locations->nlocations = 0;
 	status = nfs4_call_sync(client, server, &msg, &args.seq_args, &res.seq_res, 0);
@@ -7883,18 +7984,18 @@
  * appended to this compound to identify the client ID which is
  * performing recovery.
  */
-static int _nfs40_proc_get_locations(struct inode *inode,
+static int _nfs40_proc_get_locations(struct nfs_server *server,
+				     struct nfs_fh *fhandle,
 				     struct nfs4_fs_locations *locations,
 				     struct page *page, const struct cred *cred)
 {
-	struct nfs_server *server = NFS_SERVER(inode);
 	struct rpc_clnt *clnt = server->client;
 	u32 bitmask[2] = {
 		[0] = FATTR4_WORD0_FSID | FATTR4_WORD0_FS_LOCATIONS,
 	};
 	struct nfs4_fs_locations_arg args = {
 		.clientid	= server->nfs_client->cl_clientid,
-		.fh		= NFS_FH(inode),
+		.fh		= fhandle,
 		.page		= page,
 		.bitmask	= bitmask,
 		.migration	= 1,		/* skip LOOKUP */
@@ -7914,7 +8015,7 @@
 	unsigned long now = jiffies;
 	int status;
 
-	nfs_fattr_init(&locations->fattr);
+	nfs_fattr_init(locations->fattr);
 	locations->server = server;
 	locations->nlocations = 0;
 
@@ -7940,17 +8041,17 @@
  * When the client supports GETATTR(fs_locations_info), it can
  * be plumbed in here.
  */
-static int _nfs41_proc_get_locations(struct inode *inode,
+static int _nfs41_proc_get_locations(struct nfs_server *server,
+				     struct nfs_fh *fhandle,
 				     struct nfs4_fs_locations *locations,
 				     struct page *page, const struct cred *cred)
 {
-	struct nfs_server *server = NFS_SERVER(inode);
 	struct rpc_clnt *clnt = server->client;
 	u32 bitmask[2] = {
 		[0] = FATTR4_WORD0_FSID | FATTR4_WORD0_FS_LOCATIONS,
 	};
 	struct nfs4_fs_locations_arg args = {
-		.fh		= NFS_FH(inode),
+		.fh		= fhandle,
 		.page		= page,
 		.bitmask	= bitmask,
 		.migration	= 1,		/* skip LOOKUP */
@@ -7967,7 +8068,7 @@
 	};
 	int status;
 
-	nfs_fattr_init(&locations->fattr);
+	nfs_fattr_init(locations->fattr);
 	locations->server = server;
 	locations->nlocations = 0;
 
@@ -7999,11 +8100,11 @@
  * -NFS4ERR_LEASE_MOVED is returned if the server still has leases
  * from this client that require migration recovery.
  */
-int nfs4_proc_get_locations(struct inode *inode,
+int nfs4_proc_get_locations(struct nfs_server *server,
+			    struct nfs_fh *fhandle,
 			    struct nfs4_fs_locations *locations,
 			    struct page *page, const struct cred *cred)
 {
-	struct nfs_server *server = NFS_SERVER(inode);
 	struct nfs_client *clp = server->nfs_client;
 	const struct nfs4_mig_recovery_ops *ops =
 					clp->cl_mvops->mig_recovery_ops;
@@ -8016,10 +8117,11 @@
 		(unsigned long long)server->fsid.major,
 		(unsigned long long)server->fsid.minor,
 		clp->cl_hostname);
-	nfs_display_fhandle(NFS_FH(inode), __func__);
+	nfs_display_fhandle(fhandle, __func__);
 
 	do {
-		status = ops->get_locations(inode, locations, page, cred);
+		status = ops->get_locations(server, fhandle, locations, page,
+					    cred);
 		if (status != -NFS4ERR_DELAY)
 			break;
 		nfs4_handle_exception(server, status, &exception);
@@ -8284,6 +8386,7 @@
 	case -NFS4ERR_DEADSESSION:
 		nfs4_schedule_session_recovery(clp->cl_session,
 				task->tk_status);
+		return;
 	}
 	if (args->dir == NFS4_CDFC4_FORE_OR_BOTH &&
 			res->dir != NFS4_CDFS4_BOTH) {
@@ -8621,6 +8724,8 @@
 #ifdef CONFIG_NFS_V4_1_MIGRATION
 	calldata->args.flags |= EXCHGID4_FLAG_SUPP_MOVED_MIGR;
 #endif
+	if (test_bit(NFS_CS_PNFS, &clp->cl_flags))
+		calldata->args.flags |= EXCHGID4_FLAG_USE_PNFS_DS;
 	msg.rpc_argp = &calldata->args;
 	msg.rpc_resp = &calldata->res;
 	task_setup_data.callback_data = calldata;
@@ -9254,7 +9359,7 @@
 		goto out_err;
 
 	ret = ERR_PTR(-ENOMEM);
-	calldata = kzalloc(sizeof(*calldata), GFP_NOFS);
+	calldata = kzalloc(sizeof(*calldata), GFP_KERNEL);
 	if (calldata == NULL)
 		goto out_put_clp;
 	nfs4_init_sequence(&calldata->args, &calldata->res, 0, is_privileged);
@@ -9339,6 +9444,9 @@
 		rpc_delay(task, NFS4_POLL_RETRY_MAX);
 		fallthrough;
 	case -NFS4ERR_RETRY_UNCACHED_REP:
+	case -EACCES:
+		dprintk("%s: failed to reclaim complete error %d for server %s, retrying\n",
+			__func__, task->tk_status, clp->cl_hostname);
 		return -EAGAIN;
 	case -NFS4ERR_BADSESSION:
 	case -NFS4ERR_DEADSESSION:
@@ -9488,6 +9596,7 @@
 		status = -EBUSY;
 		break;
 	case -NFS4ERR_RECALLCONFLICT:
+	case -NFS4ERR_RETURNCONFLICT:
 		status = -ERECALLCONFLICT;
 		break;
 	case -NFS4ERR_DELEG_REVOKED:
@@ -9652,13 +9761,16 @@
 		fallthrough;
 	default:
 		task->tk_status = 0;
+		lrp->res.lrs_present = 0;
 		fallthrough;
 	case 0:
 		break;
 	case -NFS4ERR_DELAY:
-		if (nfs4_async_handle_error(task, server, NULL, NULL) != -EAGAIN)
-			break;
-		goto out_restart;
+		if (nfs4_async_handle_error(task, server, NULL, NULL) ==
+		    -EAGAIN)
+			goto out_restart;
+		lrp->res.lrs_present = 0;
+		break;
 	}
 	dprintk("<-- %s\n", __func__);
 	return;
@@ -10198,7 +10310,7 @@
 		&task_setup.rpc_client, &msg);
 
 	dprintk("NFS call  free_stateid %p\n", stateid);
-	data = kmalloc(sizeof(*data), GFP_NOFS);
+	data = kmalloc(sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 	data->server = server;
@@ -10347,7 +10459,8 @@
 		| NFS_CAP_POSIX_LOCK
 		| NFS_CAP_STATEID_NFSV41
 		| NFS_CAP_ATOMIC_OPEN_V1
-		| NFS_CAP_LGOPEN,
+		| NFS_CAP_LGOPEN
+		| NFS_CAP_MOVEABLE,
 	.init_client = nfs41_init_client,
 	.shutdown_client = nfs41_shutdown_client,
 	.match_stateid = nfs41_match_stateid,
@@ -10382,7 +10495,8 @@
 		| NFS_CAP_LAYOUTSTATS
 		| NFS_CAP_CLONE
 		| NFS_CAP_LAYOUTERROR
-		| NFS_CAP_READ_PLUS,
+		| NFS_CAP_READ_PLUS
+		| NFS_CAP_MOVEABLE,
 	.init_client = nfs41_init_client,
 	.shutdown_client = nfs41_shutdown_client,
 	.match_stateid = nfs41_match_stateid,
@@ -10412,29 +10526,55 @@
 static ssize_t nfs4_listxattr(struct dentry *dentry, char *list, size_t size)
 {
 	ssize_t error, error2, error3;
+	size_t left = size;
 
-	error = generic_listxattr(dentry, list, size);
+	error = generic_listxattr(dentry, list, left);
 	if (error < 0)
 		return error;
 	if (list) {
 		list += error;
-		size -= error;
+		left -= error;
 	}
 
-	error2 = nfs4_listxattr_nfs4_label(d_inode(dentry), list, size);
+	error2 = nfs4_listxattr_nfs4_label(d_inode(dentry), list, left);
 	if (error2 < 0)
 		return error2;
 
 	if (list) {
 		list += error2;
-		size -= error2;
+		left -= error2;
 	}
 
-	error3 = nfs4_listxattr_nfs4_user(d_inode(dentry), list, size);
+	error3 = nfs4_listxattr_nfs4_user(d_inode(dentry), list, left);
 	if (error3 < 0)
 		return error3;
 
-	return error + error2 + error3;
+	error += error2 + error3;
+	if (size && error > size)
+		return -ERANGE;
+	return error;
+}
+
+static void nfs4_enable_swap(struct inode *inode)
+{
+	/* The state manager thread must always be running.
+	 * It will notice the client is a swapper, and stay put.
+	 */
+	struct nfs_client *clp = NFS_SERVER(inode)->nfs_client;
+
+	nfs4_schedule_state_manager(clp);
+}
+
+static void nfs4_disable_swap(struct inode *inode)
+{
+	/* The state manager thread will now exit once it is
+	 * woken.
+	 */
+	struct nfs_client *clp = NFS_SERVER(inode)->nfs_client;
+
+	set_bit(NFS4CLNT_RUN_MANAGER, &clp->cl_state);
+	clear_bit(NFS4CLNT_MANAGER_AVAILABLE, &clp->cl_state);
+	wake_up_var(&clp->cl_state);
 }
 
 static const struct inode_operations nfs4_dir_inode_operations = {
@@ -10513,6 +10653,9 @@
 	.free_client	= nfs4_free_client,
 	.create_server	= nfs4_create_server,
 	.clone_server	= nfs_clone_server,
+	.discover_trunking = nfs4_discover_trunking,
+	.enable_swap	= nfs4_enable_swap,
+	.disable_swap	= nfs4_disable_swap,
 };
 
 static const struct xattr_handler nfs4_xattr_nfs4_acl_handler = {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4state.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4state.c
@@ -49,6 +49,7 @@
 #include <linux/workqueue.h>
 #include <linux/bitops.h>
 #include <linux/jiffies.h>
+#include <linux/sched/mm.h>
 
 #include <linux/sunrpc/clnt.h>
 
@@ -66,6 +67,8 @@
 
 #define OPENOWNER_POOL_SIZE	8
 
+static void nfs4_state_start_reclaim_reboot(struct nfs_client *clp);
+
 const nfs4_stateid zero_stateid = {
 	{ .data = { 0 } },
 	.type = NFS4_SPECIAL_STATEID_TYPE,
@@ -329,6 +332,8 @@
 	status = nfs4_proc_create_session(clp, cred);
 	if (status != 0)
 		goto out;
+	if (!(clp->cl_exchange_flags & EXCHGID4_FLAG_CONFIRMED_R))
+		nfs4_state_start_reclaim_reboot(clp);
 	nfs41_finish_session_reset(clp);
 	nfs_mark_client_ready(clp, NFS_CS_READY);
 out:
@@ -820,7 +825,7 @@
 
 void nfs4_close_state(struct nfs4_state *state, fmode_t fmode)
 {
-	__nfs4_close(state, fmode, GFP_NOFS, 0);
+	__nfs4_close(state, fmode, GFP_KERNEL, 0);
 }
 
 void nfs4_close_sync(struct nfs4_state *state, fmode_t fmode)
@@ -1208,10 +1213,23 @@
 {
 	struct task_struct *task;
 	char buf[INET6_ADDRSTRLEN + sizeof("-manager") + 1];
+	struct rpc_clnt *clnt = clp->cl_rpcclient;
+	bool swapon = false;
 
 	set_bit(NFS4CLNT_RUN_MANAGER, &clp->cl_state);
+
+	if (atomic_read(&clnt->cl_swapper)) {
+		swapon = !test_and_set_bit(NFS4CLNT_MANAGER_AVAILABLE,
+					   &clp->cl_state);
+		if (!swapon) {
+			wake_up_var(&clp->cl_state);
+			return;
+		}
+	}
+
 	if (test_and_set_bit(NFS4CLNT_MANAGER_RUNNING, &clp->cl_state) != 0)
 		return;
+
 	__module_get(THIS_MODULE);
 	refcount_inc(&clp->cl_count);
 
@@ -1226,6 +1244,10 @@
 	if (IS_ERR(task)) {
 		printk(KERN_ERR "%s: kthread_run: %ld\n",
 			__func__, PTR_ERR(task));
+		if (!nfs_client_init_is_complete(clp))
+			nfs_mark_client_ready(clp, PTR_ERR(task));
+		if (swapon)
+			clear_bit(NFS4CLNT_MANAGER_AVAILABLE, &clp->cl_state);
 		nfs4_clear_state_manager_bit(clp);
 		nfs_put_client(clp);
 		module_put(THIS_MODULE);
@@ -1575,7 +1597,7 @@
 			complete(&copy->completion);
 		}
 	}
-	list_for_each_entry(copy, &sp->so_server->ss_copies, src_copies) {
+	list_for_each_entry(copy, &sp->so_server->ss_src_copies, src_copies) {
 		if ((test_bit(NFS_CLNT_SRC_SSC_COPY_STATE, &state->flags) &&
 				!nfs4_stateid_match_other(&state->stateid,
 				&copy->parent_src_state->stateid)))
@@ -1777,6 +1799,7 @@
 
 static void nfs4_state_start_reclaim_reboot(struct nfs_client *clp)
 {
+	set_bit(NFS4CLNT_RECLAIM_REBOOT, &clp->cl_state);
 	/* Mark all delegations for reclaim */
 	nfs_delegation_mark_reclaim(clp);
 	nfs4_state_mark_reclaim_helper(clp, nfs4_state_mark_reclaim_reboot);
@@ -1926,6 +1949,7 @@
 				set_bit(ops->owner_flag_bit, &sp->so_flags);
 				nfs4_put_state_owner(sp);
 				status = nfs4_recovery_handle_error(clp, status);
+				nfs4_free_state_owners(&freeme);
 				return (status != 0) ? status : -EAGAIN;
 			}
 
@@ -2079,6 +2103,7 @@
 {
 	struct nfs_client *clp = server->nfs_client;
 	struct nfs4_fs_locations *locations = NULL;
+	struct nfs_fattr *fattr;
 	struct inode *inode;
 	struct page *page;
 	int status, result;
@@ -2088,16 +2113,19 @@
 			(unsigned long long)server->fsid.minor,
 			clp->cl_hostname);
 
-	result = 0;
 	page = alloc_page(GFP_KERNEL);
 	locations = kmalloc(sizeof(struct nfs4_fs_locations), GFP_KERNEL);
-	if (page == NULL || locations == NULL) {
+	fattr = nfs_alloc_fattr();
+	if (page == NULL || locations == NULL || fattr == NULL) {
 		dprintk("<-- %s: no memory\n", __func__);
+		result = 0;
 		goto out;
 	}
 
+	locations->fattr = fattr;
 	inode = d_inode(server->super->s_root);
-	result = nfs4_proc_get_locations(inode, locations, page, cred);
+	result = nfs4_proc_get_locations(server, NFS_FH(inode), locations,
+					 page, cred);
 	if (result) {
 		dprintk("<-- %s: failed to retrieve fs_locations: %d\n",
 			__func__, result);
@@ -2105,7 +2133,10 @@
 	}
 
 	result = -NFS4ERR_NXIO;
-	if (!(locations->fattr.valid & NFS_ATTR_FATTR_V4_LOCATIONS)) {
+	if (!locations->nlocations)
+		goto out;
+
+	if (!(locations->fattr->valid & NFS_ATTR_FATTR_V4_LOCATIONS)) {
 		dprintk("<-- %s: No fs_locations data, migration skipped\n",
 			__func__);
 		goto out;
@@ -2130,6 +2161,8 @@
 out:
 	if (page != NULL)
 		__free_page(page);
+	if (locations != NULL)
+		kfree(locations->fattr);
 	kfree(locations);
 	if (result) {
 		pr_err("NFS: migration recovery failed (server %s)\n",
@@ -2555,9 +2588,17 @@
 
 static void nfs4_state_manager(struct nfs_client *clp)
 {
+	unsigned int memflags;
 	int status = 0;
 	const char *section = "", *section_sep = "";
 
+	/*
+	 * State recovery can deadlock if the direct reclaim code tries
+	 * start NFS writeback. So ensure memory allocations are all
+	 * GFP_NOFS.
+	 */
+	memflags = memalloc_nofs_save();
+
 	/* Ensure exclusive access to NFSv4 state */
 	do {
 		trace_nfs4_state_mgr(clp);
@@ -2631,6 +2672,7 @@
 			if (status < 0)
 				goto out_error;
 			nfs4_state_end_reclaim_reboot(clp);
+			continue;
 		}
 
 		/* Detect expired delegations... */
@@ -2652,9 +2694,17 @@
 			clear_bit(NFS4CLNT_RECLAIM_NOGRACE, &clp->cl_state);
 		}
 
+		memalloc_nofs_restore(memflags);
 		nfs4_end_drain_session(clp);
 		nfs4_clear_state_manager_bit(clp);
 
+		if (test_bit(NFS4CLNT_RUN_MANAGER, &clp->cl_state) &&
+		    !test_and_set_bit(NFS4CLNT_MANAGER_RUNNING,
+				      &clp->cl_state)) {
+			memflags = memalloc_nofs_save();
+			continue;
+		}
+
 		if (!test_and_set_bit(NFS4CLNT_RECALL_RUNNING, &clp->cl_state)) {
 			if (test_and_clear_bit(NFS4CLNT_DELEGRETURN, &clp->cl_state)) {
 				nfs_client_return_marked_delegations(clp);
@@ -2664,11 +2714,8 @@
 			clear_bit(NFS4CLNT_RECALL_RUNNING, &clp->cl_state);
 		}
 
-		/* Did we race with an attempt to give us more work? */
-		if (!test_bit(NFS4CLNT_RUN_MANAGER, &clp->cl_state))
-			return;
-		if (test_and_set_bit(NFS4CLNT_MANAGER_RUNNING, &clp->cl_state) != 0)
-			return;
+		return;
+
 	} while (refcount_read(&clp->cl_count) > 1 && !signalled());
 	goto out_drain;
 
@@ -2681,6 +2728,7 @@
 			clp->cl_hostname, -status);
 	ssleep(1);
 out_drain:
+	memalloc_nofs_restore(memflags);
 	nfs4_end_drain_session(clp);
 	nfs4_clear_state_manager_bit(clp);
 }
@@ -2688,10 +2736,35 @@
 static int nfs4_run_state_manager(void *ptr)
 {
 	struct nfs_client *clp = ptr;
+	struct rpc_clnt *cl = clp->cl_rpcclient;
+
+	while (cl != cl->cl_parent)
+		cl = cl->cl_parent;
 
 	allow_signal(SIGKILL);
+again:
 	nfs4_state_manager(clp);
+
+	if (test_bit(NFS4CLNT_MANAGER_AVAILABLE, &clp->cl_state) &&
+	    !test_bit(NFS4CLNT_MANAGER_RUNNING, &clp->cl_state)) {
+		wait_var_event_interruptible(&clp->cl_state,
+					     test_bit(NFS4CLNT_RUN_MANAGER,
+						      &clp->cl_state));
+		if (!atomic_read(&cl->cl_swapper))
+			clear_bit(NFS4CLNT_MANAGER_AVAILABLE, &clp->cl_state);
+		if (refcount_read(&clp->cl_count) > 1 && !signalled() &&
+		    !test_and_set_bit(NFS4CLNT_MANAGER_RUNNING, &clp->cl_state))
+			goto again;
+		/* Either no longer a swapper, or were signalled */
+		clear_bit(NFS4CLNT_MANAGER_AVAILABLE, &clp->cl_state);
+	}
+
+	if (refcount_read(&clp->cl_count) > 1 && !signalled() &&
+	    test_bit(NFS4CLNT_RUN_MANAGER, &clp->cl_state) &&
+	    !test_and_set_bit(NFS4CLNT_MANAGER_RUNNING, &clp->cl_state))
+		goto again;
+
 	nfs_put_client(clp);
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4trace.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4trace.h
@@ -9,322 +9,10 @@
 #define _TRACE_NFS4_H
 
 #include <linux/tracepoint.h>
+#include <trace/misc/sunrpc.h>
 
-TRACE_DEFINE_ENUM(EPERM);
-TRACE_DEFINE_ENUM(ENOENT);
-TRACE_DEFINE_ENUM(EIO);
-TRACE_DEFINE_ENUM(ENXIO);
-TRACE_DEFINE_ENUM(EACCES);
-TRACE_DEFINE_ENUM(EEXIST);
-TRACE_DEFINE_ENUM(EXDEV);
-TRACE_DEFINE_ENUM(ENOTDIR);
-TRACE_DEFINE_ENUM(EISDIR);
-TRACE_DEFINE_ENUM(EFBIG);
-TRACE_DEFINE_ENUM(ENOSPC);
-TRACE_DEFINE_ENUM(EROFS);
-TRACE_DEFINE_ENUM(EMLINK);
-TRACE_DEFINE_ENUM(ENAMETOOLONG);
-TRACE_DEFINE_ENUM(ENOTEMPTY);
-TRACE_DEFINE_ENUM(EDQUOT);
-TRACE_DEFINE_ENUM(ESTALE);
-TRACE_DEFINE_ENUM(EBADHANDLE);
-TRACE_DEFINE_ENUM(EBADCOOKIE);
-TRACE_DEFINE_ENUM(ENOTSUPP);
-TRACE_DEFINE_ENUM(ETOOSMALL);
-TRACE_DEFINE_ENUM(EREMOTEIO);
-TRACE_DEFINE_ENUM(EBADTYPE);
-TRACE_DEFINE_ENUM(EAGAIN);
-TRACE_DEFINE_ENUM(ELOOP);
-TRACE_DEFINE_ENUM(EOPNOTSUPP);
-TRACE_DEFINE_ENUM(EDEADLK);
-TRACE_DEFINE_ENUM(ENOMEM);
-TRACE_DEFINE_ENUM(EKEYEXPIRED);
-TRACE_DEFINE_ENUM(ETIMEDOUT);
-TRACE_DEFINE_ENUM(ERESTARTSYS);
-TRACE_DEFINE_ENUM(ECONNREFUSED);
-TRACE_DEFINE_ENUM(ECONNRESET);
-TRACE_DEFINE_ENUM(ENETUNREACH);
-TRACE_DEFINE_ENUM(EHOSTUNREACH);
-TRACE_DEFINE_ENUM(EHOSTDOWN);
-TRACE_DEFINE_ENUM(EPIPE);
-TRACE_DEFINE_ENUM(EPFNOSUPPORT);
-TRACE_DEFINE_ENUM(EPROTONOSUPPORT);
-
-TRACE_DEFINE_ENUM(NFS4_OK);
-TRACE_DEFINE_ENUM(NFS4ERR_ACCESS);
-TRACE_DEFINE_ENUM(NFS4ERR_ATTRNOTSUPP);
-TRACE_DEFINE_ENUM(NFS4ERR_ADMIN_REVOKED);
-TRACE_DEFINE_ENUM(NFS4ERR_BACK_CHAN_BUSY);
-TRACE_DEFINE_ENUM(NFS4ERR_BADCHAR);
-TRACE_DEFINE_ENUM(NFS4ERR_BADHANDLE);
-TRACE_DEFINE_ENUM(NFS4ERR_BADIOMODE);
-TRACE_DEFINE_ENUM(NFS4ERR_BADLAYOUT);
-TRACE_DEFINE_ENUM(NFS4ERR_BADLABEL);
-TRACE_DEFINE_ENUM(NFS4ERR_BADNAME);
-TRACE_DEFINE_ENUM(NFS4ERR_BADOWNER);
-TRACE_DEFINE_ENUM(NFS4ERR_BADSESSION);
-TRACE_DEFINE_ENUM(NFS4ERR_BADSLOT);
-TRACE_DEFINE_ENUM(NFS4ERR_BADTYPE);
-TRACE_DEFINE_ENUM(NFS4ERR_BADXDR);
-TRACE_DEFINE_ENUM(NFS4ERR_BAD_COOKIE);
-TRACE_DEFINE_ENUM(NFS4ERR_BAD_HIGH_SLOT);
-TRACE_DEFINE_ENUM(NFS4ERR_BAD_RANGE);
-TRACE_DEFINE_ENUM(NFS4ERR_BAD_SEQID);
-TRACE_DEFINE_ENUM(NFS4ERR_BAD_SESSION_DIGEST);
-TRACE_DEFINE_ENUM(NFS4ERR_BAD_STATEID);
-TRACE_DEFINE_ENUM(NFS4ERR_CB_PATH_DOWN);
-TRACE_DEFINE_ENUM(NFS4ERR_CLID_INUSE);
-TRACE_DEFINE_ENUM(NFS4ERR_CLIENTID_BUSY);
-TRACE_DEFINE_ENUM(NFS4ERR_COMPLETE_ALREADY);
-TRACE_DEFINE_ENUM(NFS4ERR_CONN_NOT_BOUND_TO_SESSION);
-TRACE_DEFINE_ENUM(NFS4ERR_DEADLOCK);
-TRACE_DEFINE_ENUM(NFS4ERR_DEADSESSION);
-TRACE_DEFINE_ENUM(NFS4ERR_DELAY);
-TRACE_DEFINE_ENUM(NFS4ERR_DELEG_ALREADY_WANTED);
-TRACE_DEFINE_ENUM(NFS4ERR_DELEG_REVOKED);
-TRACE_DEFINE_ENUM(NFS4ERR_DENIED);
-TRACE_DEFINE_ENUM(NFS4ERR_DIRDELEG_UNAVAIL);
-TRACE_DEFINE_ENUM(NFS4ERR_DQUOT);
-TRACE_DEFINE_ENUM(NFS4ERR_ENCR_ALG_UNSUPP);
-TRACE_DEFINE_ENUM(NFS4ERR_EXIST);
-TRACE_DEFINE_ENUM(NFS4ERR_EXPIRED);
-TRACE_DEFINE_ENUM(NFS4ERR_FBIG);
-TRACE_DEFINE_ENUM(NFS4ERR_FHEXPIRED);
-TRACE_DEFINE_ENUM(NFS4ERR_FILE_OPEN);
-TRACE_DEFINE_ENUM(NFS4ERR_GRACE);
-TRACE_DEFINE_ENUM(NFS4ERR_HASH_ALG_UNSUPP);
-TRACE_DEFINE_ENUM(NFS4ERR_INVAL);
-TRACE_DEFINE_ENUM(NFS4ERR_IO);
-TRACE_DEFINE_ENUM(NFS4ERR_ISDIR);
-TRACE_DEFINE_ENUM(NFS4ERR_LAYOUTTRYLATER);
-TRACE_DEFINE_ENUM(NFS4ERR_LAYOUTUNAVAILABLE);
-TRACE_DEFINE_ENUM(NFS4ERR_LEASE_MOVED);
-TRACE_DEFINE_ENUM(NFS4ERR_LOCKED);
-TRACE_DEFINE_ENUM(NFS4ERR_LOCKS_HELD);
-TRACE_DEFINE_ENUM(NFS4ERR_LOCK_RANGE);
-TRACE_DEFINE_ENUM(NFS4ERR_MINOR_VERS_MISMATCH);
-TRACE_DEFINE_ENUM(NFS4ERR_MLINK);
-TRACE_DEFINE_ENUM(NFS4ERR_MOVED);
-TRACE_DEFINE_ENUM(NFS4ERR_NAMETOOLONG);
-TRACE_DEFINE_ENUM(NFS4ERR_NOENT);
-TRACE_DEFINE_ENUM(NFS4ERR_NOFILEHANDLE);
-TRACE_DEFINE_ENUM(NFS4ERR_NOMATCHING_LAYOUT);
-TRACE_DEFINE_ENUM(NFS4ERR_NOSPC);
-TRACE_DEFINE_ENUM(NFS4ERR_NOTDIR);
-TRACE_DEFINE_ENUM(NFS4ERR_NOTEMPTY);
-TRACE_DEFINE_ENUM(NFS4ERR_NOTSUPP);
-TRACE_DEFINE_ENUM(NFS4ERR_NOT_ONLY_OP);
-TRACE_DEFINE_ENUM(NFS4ERR_NOT_SAME);
-TRACE_DEFINE_ENUM(NFS4ERR_NO_GRACE);
-TRACE_DEFINE_ENUM(NFS4ERR_NXIO);
-TRACE_DEFINE_ENUM(NFS4ERR_OLD_STATEID);
-TRACE_DEFINE_ENUM(NFS4ERR_OPENMODE);
-TRACE_DEFINE_ENUM(NFS4ERR_OP_ILLEGAL);
-TRACE_DEFINE_ENUM(NFS4ERR_OP_NOT_IN_SESSION);
-TRACE_DEFINE_ENUM(NFS4ERR_PERM);
-TRACE_DEFINE_ENUM(NFS4ERR_PNFS_IO_HOLE);
-TRACE_DEFINE_ENUM(NFS4ERR_PNFS_NO_LAYOUT);
-TRACE_DEFINE_ENUM(NFS4ERR_RECALLCONFLICT);
-TRACE_DEFINE_ENUM(NFS4ERR_RECLAIM_BAD);
-TRACE_DEFINE_ENUM(NFS4ERR_RECLAIM_CONFLICT);
-TRACE_DEFINE_ENUM(NFS4ERR_REJECT_DELEG);
-TRACE_DEFINE_ENUM(NFS4ERR_REP_TOO_BIG);
-TRACE_DEFINE_ENUM(NFS4ERR_REP_TOO_BIG_TO_CACHE);
-TRACE_DEFINE_ENUM(NFS4ERR_REQ_TOO_BIG);
-TRACE_DEFINE_ENUM(NFS4ERR_RESOURCE);
-TRACE_DEFINE_ENUM(NFS4ERR_RESTOREFH);
-TRACE_DEFINE_ENUM(NFS4ERR_RETRY_UNCACHED_REP);
-TRACE_DEFINE_ENUM(NFS4ERR_RETURNCONFLICT);
-TRACE_DEFINE_ENUM(NFS4ERR_ROFS);
-TRACE_DEFINE_ENUM(NFS4ERR_SAME);
-TRACE_DEFINE_ENUM(NFS4ERR_SHARE_DENIED);
-TRACE_DEFINE_ENUM(NFS4ERR_SEQUENCE_POS);
-TRACE_DEFINE_ENUM(NFS4ERR_SEQ_FALSE_RETRY);
-TRACE_DEFINE_ENUM(NFS4ERR_SEQ_MISORDERED);
-TRACE_DEFINE_ENUM(NFS4ERR_SERVERFAULT);
-TRACE_DEFINE_ENUM(NFS4ERR_STALE);
-TRACE_DEFINE_ENUM(NFS4ERR_STALE_CLIENTID);
-TRACE_DEFINE_ENUM(NFS4ERR_STALE_STATEID);
-TRACE_DEFINE_ENUM(NFS4ERR_SYMLINK);
-TRACE_DEFINE_ENUM(NFS4ERR_TOOSMALL);
-TRACE_DEFINE_ENUM(NFS4ERR_TOO_MANY_OPS);
-TRACE_DEFINE_ENUM(NFS4ERR_UNKNOWN_LAYOUTTYPE);
-TRACE_DEFINE_ENUM(NFS4ERR_UNSAFE_COMPOUND);
-TRACE_DEFINE_ENUM(NFS4ERR_WRONGSEC);
-TRACE_DEFINE_ENUM(NFS4ERR_WRONG_CRED);
-TRACE_DEFINE_ENUM(NFS4ERR_WRONG_TYPE);
-TRACE_DEFINE_ENUM(NFS4ERR_XDEV);
-
-TRACE_DEFINE_ENUM(NFS4ERR_RESET_TO_MDS);
-TRACE_DEFINE_ENUM(NFS4ERR_RESET_TO_PNFS);
-
-#define show_nfsv4_errors(error) \
-	__print_symbolic(error, \
-		{ NFS4_OK, "OK" }, \
-		/* Mapped by nfs4_stat_to_errno() */ \
-		{ EPERM, "EPERM" }, \
-		{ ENOENT, "ENOENT" }, \
-		{ EIO, "EIO" }, \
-		{ ENXIO, "ENXIO" }, \
-		{ EACCES, "EACCES" }, \
-		{ EEXIST, "EEXIST" }, \
-		{ EXDEV, "EXDEV" }, \
-		{ ENOTDIR, "ENOTDIR" }, \
-		{ EISDIR, "EISDIR" }, \
-		{ EFBIG, "EFBIG" }, \
-		{ ENOSPC, "ENOSPC" }, \
-		{ EROFS, "EROFS" }, \
-		{ EMLINK, "EMLINK" }, \
-		{ ENAMETOOLONG, "ENAMETOOLONG" }, \
-		{ ENOTEMPTY, "ENOTEMPTY" }, \
-		{ EDQUOT, "EDQUOT" }, \
-		{ ESTALE, "ESTALE" }, \
-		{ EBADHANDLE, "EBADHANDLE" }, \
-		{ EBADCOOKIE, "EBADCOOKIE" }, \
-		{ ENOTSUPP, "ENOTSUPP" }, \
-		{ ETOOSMALL, "ETOOSMALL" }, \
-		{ EREMOTEIO, "EREMOTEIO" }, \
-		{ EBADTYPE, "EBADTYPE" }, \
-		{ EAGAIN, "EAGAIN" }, \
-		{ ELOOP, "ELOOP" }, \
-		{ EOPNOTSUPP, "EOPNOTSUPP" }, \
-		{ EDEADLK, "EDEADLK" }, \
-		/* RPC errors */ \
-		{ ENOMEM, "ENOMEM" }, \
-		{ EKEYEXPIRED, "EKEYEXPIRED" }, \
-		{ ETIMEDOUT, "ETIMEDOUT" }, \
-		{ ERESTARTSYS, "ERESTARTSYS" }, \
-		{ ECONNREFUSED, "ECONNREFUSED" }, \
-		{ ECONNRESET, "ECONNRESET" }, \
-		{ ENETUNREACH, "ENETUNREACH" }, \
-		{ EHOSTUNREACH, "EHOSTUNREACH" }, \
-		{ EHOSTDOWN, "EHOSTDOWN" }, \
-		{ EPIPE, "EPIPE" }, \
-		{ EPFNOSUPPORT, "EPFNOSUPPORT" }, \
-		{ EPROTONOSUPPORT, "EPROTONOSUPPORT" }, \
-		/* NFSv4 native errors */ \
-		{ NFS4ERR_ACCESS, "ACCESS" }, \
-		{ NFS4ERR_ATTRNOTSUPP, "ATTRNOTSUPP" }, \
-		{ NFS4ERR_ADMIN_REVOKED, "ADMIN_REVOKED" }, \
-		{ NFS4ERR_BACK_CHAN_BUSY, "BACK_CHAN_BUSY" }, \
-		{ NFS4ERR_BADCHAR, "BADCHAR" }, \
-		{ NFS4ERR_BADHANDLE, "BADHANDLE" }, \
-		{ NFS4ERR_BADIOMODE, "BADIOMODE" }, \
-		{ NFS4ERR_BADLAYOUT, "BADLAYOUT" }, \
-		{ NFS4ERR_BADLABEL, "BADLABEL" }, \
-		{ NFS4ERR_BADNAME, "BADNAME" }, \
-		{ NFS4ERR_BADOWNER, "BADOWNER" }, \
-		{ NFS4ERR_BADSESSION, "BADSESSION" }, \
-		{ NFS4ERR_BADSLOT, "BADSLOT" }, \
-		{ NFS4ERR_BADTYPE, "BADTYPE" }, \
-		{ NFS4ERR_BADXDR, "BADXDR" }, \
-		{ NFS4ERR_BAD_COOKIE, "BAD_COOKIE" }, \
-		{ NFS4ERR_BAD_HIGH_SLOT, "BAD_HIGH_SLOT" }, \
-		{ NFS4ERR_BAD_RANGE, "BAD_RANGE" }, \
-		{ NFS4ERR_BAD_SEQID, "BAD_SEQID" }, \
-		{ NFS4ERR_BAD_SESSION_DIGEST, "BAD_SESSION_DIGEST" }, \
-		{ NFS4ERR_BAD_STATEID, "BAD_STATEID" }, \
-		{ NFS4ERR_CB_PATH_DOWN, "CB_PATH_DOWN" }, \
-		{ NFS4ERR_CLID_INUSE, "CLID_INUSE" }, \
-		{ NFS4ERR_CLIENTID_BUSY, "CLIENTID_BUSY" }, \
-		{ NFS4ERR_COMPLETE_ALREADY, "COMPLETE_ALREADY" }, \
-		{ NFS4ERR_CONN_NOT_BOUND_TO_SESSION, \
-			"CONN_NOT_BOUND_TO_SESSION" }, \
-		{ NFS4ERR_DEADLOCK, "DEADLOCK" }, \
-		{ NFS4ERR_DEADSESSION, "DEAD_SESSION" }, \
-		{ NFS4ERR_DELAY, "DELAY" }, \
-		{ NFS4ERR_DELEG_ALREADY_WANTED, \
-			"DELEG_ALREADY_WANTED" }, \
-		{ NFS4ERR_DELEG_REVOKED, "DELEG_REVOKED" }, \
-		{ NFS4ERR_DENIED, "DENIED" }, \
-		{ NFS4ERR_DIRDELEG_UNAVAIL, "DIRDELEG_UNAVAIL" }, \
-		{ NFS4ERR_DQUOT, "DQUOT" }, \
-		{ NFS4ERR_ENCR_ALG_UNSUPP, "ENCR_ALG_UNSUPP" }, \
-		{ NFS4ERR_EXIST, "EXIST" }, \
-		{ NFS4ERR_EXPIRED, "EXPIRED" }, \
-		{ NFS4ERR_FBIG, "FBIG" }, \
-		{ NFS4ERR_FHEXPIRED, "FHEXPIRED" }, \
-		{ NFS4ERR_FILE_OPEN, "FILE_OPEN" }, \
-		{ NFS4ERR_GRACE, "GRACE" }, \
-		{ NFS4ERR_HASH_ALG_UNSUPP, "HASH_ALG_UNSUPP" }, \
-		{ NFS4ERR_INVAL, "INVAL" }, \
-		{ NFS4ERR_IO, "IO" }, \
-		{ NFS4ERR_ISDIR, "ISDIR" }, \
-		{ NFS4ERR_LAYOUTTRYLATER, "LAYOUTTRYLATER" }, \
-		{ NFS4ERR_LAYOUTUNAVAILABLE, "LAYOUTUNAVAILABLE" }, \
-		{ NFS4ERR_LEASE_MOVED, "LEASE_MOVED" }, \
-		{ NFS4ERR_LOCKED, "LOCKED" }, \
-		{ NFS4ERR_LOCKS_HELD, "LOCKS_HELD" }, \
-		{ NFS4ERR_LOCK_RANGE, "LOCK_RANGE" }, \
-		{ NFS4ERR_MINOR_VERS_MISMATCH, "MINOR_VERS_MISMATCH" }, \
-		{ NFS4ERR_MLINK, "MLINK" }, \
-		{ NFS4ERR_MOVED, "MOVED" }, \
-		{ NFS4ERR_NAMETOOLONG, "NAMETOOLONG" }, \
-		{ NFS4ERR_NOENT, "NOENT" }, \
-		{ NFS4ERR_NOFILEHANDLE, "NOFILEHANDLE" }, \
-		{ NFS4ERR_NOMATCHING_LAYOUT, "NOMATCHING_LAYOUT" }, \
-		{ NFS4ERR_NOSPC, "NOSPC" }, \
-		{ NFS4ERR_NOTDIR, "NOTDIR" }, \
-		{ NFS4ERR_NOTEMPTY, "NOTEMPTY" }, \
-		{ NFS4ERR_NOTSUPP, "NOTSUPP" }, \
-		{ NFS4ERR_NOT_ONLY_OP, "NOT_ONLY_OP" }, \
-		{ NFS4ERR_NOT_SAME, "NOT_SAME" }, \
-		{ NFS4ERR_NO_GRACE, "NO_GRACE" }, \
-		{ NFS4ERR_NXIO, "NXIO" }, \
-		{ NFS4ERR_OLD_STATEID, "OLD_STATEID" }, \
-		{ NFS4ERR_OPENMODE, "OPENMODE" }, \
-		{ NFS4ERR_OP_ILLEGAL, "OP_ILLEGAL" }, \
-		{ NFS4ERR_OP_NOT_IN_SESSION, "OP_NOT_IN_SESSION" }, \
-		{ NFS4ERR_PERM, "PERM" }, \
-		{ NFS4ERR_PNFS_IO_HOLE, "PNFS_IO_HOLE" }, \
-		{ NFS4ERR_PNFS_NO_LAYOUT, "PNFS_NO_LAYOUT" }, \
-		{ NFS4ERR_RECALLCONFLICT, "RECALLCONFLICT" }, \
-		{ NFS4ERR_RECLAIM_BAD, "RECLAIM_BAD" }, \
-		{ NFS4ERR_RECLAIM_CONFLICT, "RECLAIM_CONFLICT" }, \
-		{ NFS4ERR_REJECT_DELEG, "REJECT_DELEG" }, \
-		{ NFS4ERR_REP_TOO_BIG, "REP_TOO_BIG" }, \
-		{ NFS4ERR_REP_TOO_BIG_TO_CACHE, \
-			"REP_TOO_BIG_TO_CACHE" }, \
-		{ NFS4ERR_REQ_TOO_BIG, "REQ_TOO_BIG" }, \
-		{ NFS4ERR_RESOURCE, "RESOURCE" }, \
-		{ NFS4ERR_RESTOREFH, "RESTOREFH" }, \
-		{ NFS4ERR_RETRY_UNCACHED_REP, "RETRY_UNCACHED_REP" }, \
-		{ NFS4ERR_RETURNCONFLICT, "RETURNCONFLICT" }, \
-		{ NFS4ERR_ROFS, "ROFS" }, \
-		{ NFS4ERR_SAME, "SAME" }, \
-		{ NFS4ERR_SHARE_DENIED, "SHARE_DENIED" }, \
-		{ NFS4ERR_SEQUENCE_POS, "SEQUENCE_POS" }, \
-		{ NFS4ERR_SEQ_FALSE_RETRY, "SEQ_FALSE_RETRY" }, \
-		{ NFS4ERR_SEQ_MISORDERED, "SEQ_MISORDERED" }, \
-		{ NFS4ERR_SERVERFAULT, "SERVERFAULT" }, \
-		{ NFS4ERR_STALE, "STALE" }, \
-		{ NFS4ERR_STALE_CLIENTID, "STALE_CLIENTID" }, \
-		{ NFS4ERR_STALE_STATEID, "STALE_STATEID" }, \
-		{ NFS4ERR_SYMLINK, "SYMLINK" }, \
-		{ NFS4ERR_TOOSMALL, "TOOSMALL" }, \
-		{ NFS4ERR_TOO_MANY_OPS, "TOO_MANY_OPS" }, \
-		{ NFS4ERR_UNKNOWN_LAYOUTTYPE, "UNKNOWN_LAYOUTTYPE" }, \
-		{ NFS4ERR_UNSAFE_COMPOUND, "UNSAFE_COMPOUND" }, \
-		{ NFS4ERR_WRONGSEC, "WRONGSEC" }, \
-		{ NFS4ERR_WRONG_CRED, "WRONG_CRED" }, \
-		{ NFS4ERR_WRONG_TYPE, "WRONG_TYPE" }, \
-		{ NFS4ERR_XDEV, "XDEV" }, \
-		/* ***** Internal to Linux NFS client ***** */ \
-		{ NFS4ERR_RESET_TO_MDS, "RESET_TO_MDS" }, \
-		{ NFS4ERR_RESET_TO_PNFS, "RESET_TO_PNFS" })
-
-#define show_open_flags(flags) \
-	__print_flags(flags, "|", \
-		{ O_CREAT, "O_CREAT" }, \
-		{ O_EXCL, "O_EXCL" }, \
-		{ O_TRUNC, "O_TRUNC" }, \
-		{ O_DIRECT, "O_DIRECT" })
-
-#define show_fmode_flags(mode) \
-	__print_flags(mode, "|", \
-		{ ((__force unsigned long)FMODE_READ), "READ" }, \
-		{ ((__force unsigned long)FMODE_WRITE), "WRITE" }, \
-		{ ((__force unsigned long)FMODE_EXEC), "EXEC" })
+#include <trace/misc/fs.h>
+#include <trace/misc/nfs.h>
 
 #define show_nfs_fattr_flags(valid) \
 	__print_flags((unsigned long)valid, "|", \
@@ -365,7 +53,7 @@
 		TP_printk(
 			"error=%ld (%s) dstaddr=%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			__get_str(dstaddr)
 		)
 );
@@ -389,29 +77,6 @@
 DEFINE_NFS4_CLIENTID_EVENT(nfs4_sequence);
 DEFINE_NFS4_CLIENTID_EVENT(nfs4_reclaim_complete);
 
-#define show_nfs4_sequence_status_flags(status) \
-	__print_flags((unsigned long)status, "|", \
-		{ SEQ4_STATUS_CB_PATH_DOWN, "CB_PATH_DOWN" }, \
-		{ SEQ4_STATUS_CB_GSS_CONTEXTS_EXPIRING, \
-			"CB_GSS_CONTEXTS_EXPIRING" }, \
-		{ SEQ4_STATUS_CB_GSS_CONTEXTS_EXPIRED, \
-			"CB_GSS_CONTEXTS_EXPIRED" }, \
-		{ SEQ4_STATUS_EXPIRED_ALL_STATE_REVOKED, \
-			"EXPIRED_ALL_STATE_REVOKED" }, \
-		{ SEQ4_STATUS_EXPIRED_SOME_STATE_REVOKED, \
-			"EXPIRED_SOME_STATE_REVOKED" }, \
-		{ SEQ4_STATUS_ADMIN_STATE_REVOKED, \
-			"ADMIN_STATE_REVOKED" }, \
-		{ SEQ4_STATUS_RECALLABLE_STATE_REVOKED,	 \
-			"RECALLABLE_STATE_REVOKED" }, \
-		{ SEQ4_STATUS_LEASE_MOVED, "LEASE_MOVED" }, \
-		{ SEQ4_STATUS_RESTART_RECLAIM_NEEDED, \
-			"RESTART_RECLAIM_NEEDED" }, \
-		{ SEQ4_STATUS_CB_PATH_DOWN_SESSION, \
-			"CB_PATH_DOWN_SESSION" }, \
-		{ SEQ4_STATUS_BACKCHANNEL_FAULT, \
-			"BACKCHANNEL_FAULT" })
-
 TRACE_EVENT(nfs4_sequence_done,
 		TP_PROTO(
 			const struct nfs4_session *session,
@@ -425,7 +90,7 @@
 			__field(unsigned int, seq_nr)
 			__field(unsigned int, highest_slotid)
 			__field(unsigned int, target_highest_slotid)
-			__field(unsigned int, status_flags)
+			__field(unsigned long, status_flags)
 			__field(unsigned long, error)
 		),
 
@@ -444,16 +109,16 @@
 		TP_printk(
 			"error=%ld (%s) session=0x%08x slot_nr=%u seq_nr=%u "
 			"highest_slotid=%u target_highest_slotid=%u "
-			"status_flags=%u (%s)",
+			"status_flags=0x%lx (%s)",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			__entry->session,
 			__entry->slot_nr,
 			__entry->seq_nr,
 			__entry->highest_slotid,
 			__entry->target_highest_slotid,
 			__entry->status_flags,
-			show_nfs4_sequence_status_flags(__entry->status_flags)
+			show_nfs4_seq4_status(__entry->status_flags)
 		)
 );
 
@@ -490,7 +155,7 @@
 			"error=%ld (%s) session=0x%08x slot_nr=%u seq_nr=%u "
 			"highest_slotid=%u",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			__entry->session,
 			__entry->slot_nr,
 			__entry->seq_nr,
@@ -527,7 +192,7 @@
 			"error=%ld (%s) session=0x%08x slot_nr=%u seq_nr=%u "
 			"highest_slotid=%u",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			__entry->session,
 			__entry->slot_nr,
 			__entry->seq_nr,
@@ -584,32 +249,34 @@
 TRACE_DEFINE_ENUM(NFS4CLNT_LEASE_MOVED);
 TRACE_DEFINE_ENUM(NFS4CLNT_DELEGATION_EXPIRED);
 TRACE_DEFINE_ENUM(NFS4CLNT_RUN_MANAGER);
+TRACE_DEFINE_ENUM(NFS4CLNT_MANAGER_AVAILABLE);
 TRACE_DEFINE_ENUM(NFS4CLNT_RECALL_RUNNING);
 TRACE_DEFINE_ENUM(NFS4CLNT_RECALL_ANY_LAYOUT_READ);
 TRACE_DEFINE_ENUM(NFS4CLNT_RECALL_ANY_LAYOUT_RW);
+TRACE_DEFINE_ENUM(NFS4CLNT_DELEGRETURN_DELAYED);
 
 #define show_nfs4_clp_state(state) \
 	__print_flags(state, "|", \
-		{ NFS4CLNT_MANAGER_RUNNING,	"MANAGER_RUNNING" }, \
-		{ NFS4CLNT_CHECK_LEASE,		"CHECK_LEASE" }, \
-		{ NFS4CLNT_LEASE_EXPIRED,	"LEASE_EXPIRED" }, \
-		{ NFS4CLNT_RECLAIM_REBOOT,	"RECLAIM_REBOOT" }, \
-		{ NFS4CLNT_RECLAIM_NOGRACE,	"RECLAIM_NOGRACE" }, \
-		{ NFS4CLNT_DELEGRETURN,		"DELEGRETURN" }, \
-		{ NFS4CLNT_SESSION_RESET,	"SESSION_RESET" }, \
-		{ NFS4CLNT_LEASE_CONFIRM,	"LEASE_CONFIRM" }, \
-		{ NFS4CLNT_SERVER_SCOPE_MISMATCH, \
-						"SERVER_SCOPE_MISMATCH" }, \
-		{ NFS4CLNT_PURGE_STATE,		"PURGE_STATE" }, \
-		{ NFS4CLNT_BIND_CONN_TO_SESSION, \
-						"BIND_CONN_TO_SESSION" }, \
-		{ NFS4CLNT_MOVED,		"MOVED" }, \
-		{ NFS4CLNT_LEASE_MOVED,		"LEASE_MOVED" }, \
-		{ NFS4CLNT_DELEGATION_EXPIRED,	"DELEGATION_EXPIRED" }, \
-		{ NFS4CLNT_RUN_MANAGER,		"RUN_MANAGER" }, \
-		{ NFS4CLNT_RECALL_RUNNING,	"RECALL_RUNNING" }, \
-		{ NFS4CLNT_RECALL_ANY_LAYOUT_READ, "RECALL_ANY_LAYOUT_READ" }, \
-		{ NFS4CLNT_RECALL_ANY_LAYOUT_RW, "RECALL_ANY_LAYOUT_RW" })
+	{ BIT(NFS4CLNT_MANAGER_RUNNING),	"MANAGER_RUNNING" }, \
+	{ BIT(NFS4CLNT_CHECK_LEASE),		"CHECK_LEASE" }, \
+	{ BIT(NFS4CLNT_LEASE_EXPIRED),	"LEASE_EXPIRED" }, \
+	{ BIT(NFS4CLNT_RECLAIM_REBOOT),	"RECLAIM_REBOOT" }, \
+	{ BIT(NFS4CLNT_RECLAIM_NOGRACE),	"RECLAIM_NOGRACE" }, \
+	{ BIT(NFS4CLNT_DELEGRETURN),		"DELEGRETURN" }, \
+	{ BIT(NFS4CLNT_SESSION_RESET),	"SESSION_RESET" }, \
+	{ BIT(NFS4CLNT_LEASE_CONFIRM),	"LEASE_CONFIRM" }, \
+	{ BIT(NFS4CLNT_SERVER_SCOPE_MISMATCH),	"SERVER_SCOPE_MISMATCH" }, \
+	{ BIT(NFS4CLNT_PURGE_STATE),		"PURGE_STATE" }, \
+	{ BIT(NFS4CLNT_BIND_CONN_TO_SESSION),	"BIND_CONN_TO_SESSION" }, \
+	{ BIT(NFS4CLNT_MOVED),		"MOVED" }, \
+	{ BIT(NFS4CLNT_LEASE_MOVED),		"LEASE_MOVED" }, \
+	{ BIT(NFS4CLNT_DELEGATION_EXPIRED),	"DELEGATION_EXPIRED" }, \
+	{ BIT(NFS4CLNT_RUN_MANAGER),		"RUN_MANAGER" }, \
+	{ BIT(NFS4CLNT_MANAGER_AVAILABLE), "MANAGER_AVAILABLE" }, \
+	{ BIT(NFS4CLNT_RECALL_RUNNING),	"RECALL_RUNNING" }, \
+	{ BIT(NFS4CLNT_RECALL_ANY_LAYOUT_READ), "RECALL_ANY_LAYOUT_READ" }, \
+	{ BIT(NFS4CLNT_RECALL_ANY_LAYOUT_RW), "RECALL_ANY_LAYOUT_RW" }, \
+	{ BIT(NFS4CLNT_DELEGRETURN_DELAYED), "DELERETURN_DELAYED" })
 
 TRACE_EVENT(nfs4_state_mgr,
 		TP_PROTO(
@@ -661,7 +328,7 @@
 			"hostname=%s clp state=%s error=%ld (%s) section=%s",
 			__get_str(hostname),
 			show_nfs4_clp_state(__entry->state), -__entry->error,
-			show_nfsv4_errors(__entry->error), __get_str(section)
+			show_nfs4_status(__entry->error), __get_str(section)
 
 		)
 )
@@ -694,8 +361,8 @@
 			__entry->expected = expected;
 		),
 
-		TP_printk(
-			"task:%u@%d xid=0x%08x operation=%u, expected=%u",
+		TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+			  " xid=0x%08x operation=%u, expected=%u",
 			__entry->task_id, __entry->client_id, __entry->xid,
 			__entry->op, __entry->expected
 		)
@@ -729,10 +396,10 @@
 			__entry->error = error;
 		),
 
-		TP_printk(
-			"task:%u@%d xid=0x%08x error=%ld (%s) operation=%u",
+		TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+			  " xid=0x%08x error=%ld (%s) operation=%u",
 			__entry->task_id, __entry->client_id, __entry->xid,
-			-__entry->error, show_nfsv4_errors(__entry->error),
+			-__entry->error, show_nfs4_status(__entry->error),
 			__entry->op
 		)
 );
@@ -793,8 +460,8 @@
 
 		TP_STRUCT__entry(
 			__field(unsigned long, error)
-			__field(unsigned int, flags)
-			__field(unsigned int, fmode)
+			__field(unsigned long, flags)
+			__field(unsigned long, fmode)
 			__field(dev_t, dev)
 			__field(u32, fhandle)
 			__field(u64, fileid)
@@ -812,7 +479,7 @@
 
 			__entry->error = -error;
 			__entry->flags = flags;
-			__entry->fmode = (__force unsigned int)ctx->mode;
+			__entry->fmode = (__force unsigned long)ctx->mode;
 			__entry->dev = ctx->dentry->d_sb->s_dev;
 			if (!IS_ERR_OR_NULL(state)) {
 				inode = state->inode;
@@ -842,15 +509,15 @@
 		),
 
 		TP_printk(
-			"error=%ld (%s) flags=%d (%s) fmode=%s "
+			"error=%ld (%s) flags=%lu (%s) fmode=%s "
 			"fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"name=%02x:%02x:%llu/%s stateid=%d:0x%08x "
 			"openstateid=%d:0x%08x",
 			 -__entry->error,
-			 show_nfsv4_errors(__entry->error),
+			 show_nfs4_status(__entry->error),
 			 __entry->flags,
-			 show_open_flags(__entry->flags),
-			 show_fmode_flags(__entry->fmode),
+			 show_fs_fcntl_open_flags(__entry->flags),
+			 show_fs_fmode_flags(__entry->fmode),
 			 MAJOR(__entry->dev), MINOR(__entry->dev),
 			 (unsigned long long)__entry->fileid,
 			 __entry->fhandle,
@@ -904,7 +571,7 @@
 		TP_printk(
 			"fmode=%s fileid=%02x:%02x:%llu "
 			"fhandle=0x%08x stateid=%d:0x%08x",
-			__entry->fmode ?  show_fmode_flags(__entry->fmode) :
+			__entry->fmode ?  show_fs_fmode_flags(__entry->fmode) :
 					  "closed",
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
@@ -951,8 +618,8 @@
 			"error=%ld (%s) fmode=%s fileid=%02x:%02x:%llu "
 			"fhandle=0x%08x openstateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
-			__entry->fmode ?  show_fmode_flags(__entry->fmode) :
+			show_nfs4_status(__entry->error),
+			__entry->fmode ?  show_fs_fmode_flags(__entry->fmode) :
 					  "closed",
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
@@ -961,24 +628,6 @@
 		)
 );
 
-TRACE_DEFINE_ENUM(F_GETLK);
-TRACE_DEFINE_ENUM(F_SETLK);
-TRACE_DEFINE_ENUM(F_SETLKW);
-TRACE_DEFINE_ENUM(F_RDLCK);
-TRACE_DEFINE_ENUM(F_WRLCK);
-TRACE_DEFINE_ENUM(F_UNLCK);
-
-#define show_lock_cmd(type) \
-	__print_symbolic((int)type, \
-		{ F_GETLK, "GETLK" }, \
-		{ F_SETLK, "SETLK" }, \
-		{ F_SETLKW, "SETLKW" })
-#define show_lock_type(type) \
-	__print_symbolic((int)type, \
-		{ F_RDLCK, "RDLCK" }, \
-		{ F_WRLCK, "WRLCK" }, \
-		{ F_UNLCK, "UNLCK" })
-
 DECLARE_EVENT_CLASS(nfs4_lock_event,
 		TP_PROTO(
 			const struct file_lock *request,
@@ -991,8 +640,8 @@
 
 		TP_STRUCT__entry(
 			__field(unsigned long, error)
-			__field(int, cmd)
-			__field(char, type)
+			__field(unsigned long, cmd)
+			__field(unsigned long, type)
 			__field(loff_t, start)
 			__field(loff_t, end)
 			__field(dev_t, dev)
@@ -1024,9 +673,9 @@
 			"fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"stateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
-			show_lock_cmd(__entry->cmd),
-			show_lock_type(__entry->type),
+			show_nfs4_status(__entry->error),
+			show_fs_fcntl_cmd(__entry->cmd),
+			show_fs_fcntl_lock_type(__entry->type),
 			(long long)__entry->start,
 			(long long)__entry->end,
 			MAJOR(__entry->dev), MINOR(__entry->dev),
@@ -1061,8 +710,8 @@
 
 		TP_STRUCT__entry(
 			__field(unsigned long, error)
-			__field(int, cmd)
-			__field(char, type)
+			__field(unsigned long, cmd)
+			__field(unsigned long, type)
 			__field(loff_t, start)
 			__field(loff_t, end)
 			__field(dev_t, dev)
@@ -1100,9 +749,9 @@
 			"fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"stateid=%d:0x%08x lockstateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
-			show_lock_cmd(__entry->cmd),
-			show_lock_type(__entry->type),
+			show_nfs4_status(__entry->error),
+			show_fs_fcntl_cmd(__entry->cmd),
+			show_fs_fcntl_lock_type(__entry->type),
 			(long long)__entry->start,
 			(long long)__entry->end,
 			MAJOR(__entry->dev), MINOR(__entry->dev),
@@ -1219,7 +868,7 @@
 
 		TP_printk(
 			"fmode=%s fileid=%02x:%02x:%llu fhandle=0x%08x",
-			show_fmode_flags(__entry->fmode),
+			show_fs_fmode_flags(__entry->fmode),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle
@@ -1266,7 +915,7 @@
 			"error=%ld (%s) dev=%02x:%02x fhandle=0x%08x "
 			"stateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			__entry->fhandle,
 			__entry->stateid_seq, __entry->stateid_hash
@@ -1309,7 +958,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"stateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1356,7 +1005,7 @@
 		TP_printk(
 			"error=%ld (%s) name=%02x:%02x:%llu/%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -1403,7 +1052,7 @@
 		TP_printk(
 			"error=%ld (%s) inode=%02x:%02x:%llu",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->ino
 		)
@@ -1442,7 +1091,7 @@
 			"error=%ld (%s) oldname=%02x:%02x:%llu/%s "
 			"newname=%02x:%02x:%llu/%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->olddir,
 			__get_str(oldname),
@@ -1477,7 +1126,7 @@
 		TP_printk(
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle
@@ -1535,7 +1184,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"stateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1588,7 +1237,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"valid=%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1644,7 +1293,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"dstaddr=%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1705,7 +1354,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"stateid=%d:0x%08x dstaddr=%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1754,7 +1403,7 @@
 
 		TP_printk(
 			"error=%ld (%s) id=%u name=%s",
-			-__entry->error, show_nfsv4_errors(__entry->error),
+			-__entry->error, show_nfs4_status(__entry->error),
 			__entry->id,
 			__get_str(name)
 		)
@@ -1832,7 +1481,7 @@
 			"offset=%lld count=%u res=%u stateid=%d:0x%08x "
 			"layoutstateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1906,7 +1555,7 @@
 			"offset=%lld count=%u res=%u stateid=%d:0x%08x "
 			"layoutstateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1970,7 +1619,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"offset=%lld count=%u layoutstateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -1990,16 +1639,6 @@
 #ifdef CONFIG_NFS_V4_1
 DEFINE_NFS4_COMMIT_EVENT(nfs4_pnfs_commit_ds);
 
-TRACE_DEFINE_ENUM(IOMODE_READ);
-TRACE_DEFINE_ENUM(IOMODE_RW);
-TRACE_DEFINE_ENUM(IOMODE_ANY);
-
-#define show_pnfs_iomode(iomode) \
-	__print_symbolic(iomode, \
-		{ IOMODE_READ, "READ" }, \
-		{ IOMODE_RW, "RW" }, \
-		{ IOMODE_ANY, "ANY" })
-
 TRACE_EVENT(nfs4_layoutget,
 		TP_PROTO(
 			const struct nfs_open_context *ctx,
@@ -2055,11 +1694,11 @@
 			"iomode=%s offset=%llu count=%llu stateid=%d:0x%08x "
 			"layoutstateid=%d:0x%08x",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
-			show_pnfs_iomode(__entry->iomode),
+			show_pnfs_layout_iomode(__entry->iomode),
 			(unsigned long long)__entry->offset,
 			(unsigned long long)__entry->count,
 			__entry->stateid_seq, __entry->stateid_hash,
@@ -2153,7 +1792,7 @@
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
-			show_pnfs_iomode(__entry->iomode),
+			show_pnfs_layout_iomode(__entry->iomode),
 			(unsigned long long)__entry->pos,
 			(unsigned long long)__entry->count,
 			__entry->layoutstateid_seq, __entry->layoutstateid_hash,
@@ -2207,7 +1846,7 @@
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
-			show_pnfs_iomode(__entry->iomode),
+			show_pnfs_layout_iomode(__entry->iomode),
 			(unsigned long long)__entry->pos,
 			(unsigned long long)__entry->count,
 			__entry->layoutstateid_seq, __entry->layoutstateid_hash,
@@ -2352,7 +1991,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"offset=%llu count=%u stateid=%d:0x%08x dstaddr=%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
@@ -2408,7 +2047,7 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"offset=%llu count=%u dstaddr=%s",
 			-__entry->error,
-			show_nfsv4_errors(__entry->error),
+			show_nfs4_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfs4xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfs4xdr.c
@@ -3693,8 +3693,6 @@
 	if (unlikely(!p))
 		goto out_eio;
 	n = be32_to_cpup(p);
-	if (n <= 0)
-		goto out_eio;
 	for (res->nlocations = 0; res->nlocations < n; res->nlocations++) {
 		u32 m;
 		struct nfs4_fs_location *loc;
@@ -4181,26 +4179,25 @@
 		p = xdr_inline_decode(xdr, len);
 		if (unlikely(!p))
 			return -EIO;
+		bitmap[2] &= ~FATTR4_WORD2_SECURITY_LABEL;
 		if (len < NFS4_MAXLABELLEN) {
-			if (label) {
-				if (label->len) {
-					if (label->len < len)
-						return -ERANGE;
-					memcpy(label->label, p, len);
-				}
+			if (label && label->len) {
+				if (label->len < len)
+					return -ERANGE;
+				memcpy(label->label, p, len);
 				label->len = len;
 				label->pi = pi;
 				label->lfs = lfs;
 				status = NFS_ATTR_FATTR_V4_SECURITY_LABEL;
 			}
-			bitmap[2] &= ~FATTR4_WORD2_SECURITY_LABEL;
 		} else
 			printk(KERN_WARNING "%s: label too long (%u)!\n",
 					__func__, len);
+		if (label && label->label)
+			dprintk("%s: label=%.*s, len=%d, PI=%d, LFS=%d\n",
+				__func__, label->len, (char *)label->label,
+				label->len, label->pi, label->lfs);
 	}
-	if (label && label->label)
-		dprintk("%s: label=%s, len=%d, PI=%d, LFS=%d\n", __func__,
-			(char *)label->label, label->len, label->pi, label->lfs);
 	return status;
 }
 
@@ -7029,7 +7026,7 @@
 	if (res->migration) {
 		xdr_enter_page(xdr, PAGE_SIZE);
 		status = decode_getfattr_generic(xdr,
-					&res->fs_locations->fattr,
+					res->fs_locations->fattr,
 					 NULL, res->fs_locations,
 					 NULL, res->fs_locations->server);
 		if (status)
@@ -7042,7 +7039,7 @@
 			goto out;
 		xdr_enter_page(xdr, PAGE_SIZE);
 		status = decode_getfattr_generic(xdr,
-					&res->fs_locations->fattr,
+					res->fs_locations->fattr,
 					 NULL, res->fs_locations,
 					 NULL, res->fs_locations->server);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfsroot.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfsroot.c
@@ -175,10 +175,10 @@
 	size_t len = strlen(dest);
 
 	if (len && dest[len - 1] != ',')
-		if (strlcat(dest, ",", destlen) > destlen)
+		if (strlcat(dest, ",", destlen) >= destlen)
 			return -1;
 
-	if (strlcat(dest, src, destlen) > destlen)
+	if (strlcat(dest, src, destlen) >= destlen)
 		return -1;
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/nfstrace.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/nfstrace.h
@@ -11,45 +11,9 @@
 #include <linux/tracepoint.h>
 #include <linux/iversion.h>
 
-TRACE_DEFINE_ENUM(DT_UNKNOWN);
-TRACE_DEFINE_ENUM(DT_FIFO);
-TRACE_DEFINE_ENUM(DT_CHR);
-TRACE_DEFINE_ENUM(DT_DIR);
-TRACE_DEFINE_ENUM(DT_BLK);
-TRACE_DEFINE_ENUM(DT_REG);
-TRACE_DEFINE_ENUM(DT_LNK);
-TRACE_DEFINE_ENUM(DT_SOCK);
-TRACE_DEFINE_ENUM(DT_WHT);
-
-#define nfs_show_file_type(ftype) \
-	__print_symbolic(ftype, \
-			{ DT_UNKNOWN, "UNKNOWN" }, \
-			{ DT_FIFO, "FIFO" }, \
-			{ DT_CHR, "CHR" }, \
-			{ DT_DIR, "DIR" }, \
-			{ DT_BLK, "BLK" }, \
-			{ DT_REG, "REG" }, \
-			{ DT_LNK, "LNK" }, \
-			{ DT_SOCK, "SOCK" }, \
-			{ DT_WHT, "WHT" })
-
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_DATA);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_ATIME);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_ACCESS);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_ACL);
-TRACE_DEFINE_ENUM(NFS_INO_REVAL_PAGECACHE);
-TRACE_DEFINE_ENUM(NFS_INO_REVAL_FORCED);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_LABEL);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_CHANGE);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_CTIME);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_MTIME);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_SIZE);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_OTHER);
-TRACE_DEFINE_ENUM(NFS_INO_DATA_INVAL_DEFER);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_BLOCKS);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_XATTR);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_NLINK);
-TRACE_DEFINE_ENUM(NFS_INO_INVALID_MODE);
+#include <trace/misc/fs.h>
+#include <trace/misc/nfs.h>
+#include <trace/misc/sunrpc.h>
 
 #define nfs_show_cache_validity(v) \
 	__print_flags(v, "|", \
@@ -71,17 +35,6 @@
 			{ NFS_INO_INVALID_NLINK, "INVALID_NLINK" }, \
 			{ NFS_INO_INVALID_MODE, "INVALID_MODE" })
 
-TRACE_DEFINE_ENUM(NFS_INO_ADVISE_RDPLUS);
-TRACE_DEFINE_ENUM(NFS_INO_STALE);
-TRACE_DEFINE_ENUM(NFS_INO_ACL_LRU_SET);
-TRACE_DEFINE_ENUM(NFS_INO_INVALIDATING);
-TRACE_DEFINE_ENUM(NFS_INO_FSCACHE);
-TRACE_DEFINE_ENUM(NFS_INO_FSCACHE_LOCK);
-TRACE_DEFINE_ENUM(NFS_INO_LAYOUTCOMMIT);
-TRACE_DEFINE_ENUM(NFS_INO_LAYOUTCOMMITTING);
-TRACE_DEFINE_ENUM(NFS_INO_LAYOUTSTATS);
-TRACE_DEFINE_ENUM(NFS_INO_ODIRECT);
-
 #define nfs_show_nfsi_flags(v) \
 	__print_flags(v, "|", \
 			{ BIT(NFS_INO_ADVISE_RDPLUS), "ADVISE_RDPLUS" }, \
@@ -163,12 +116,12 @@
 			"error=%ld (%s) fileid=%02x:%02x:%llu fhandle=0x%08x "
 			"type=%u (%s) version=%llu size=%lld "
 			"cache_validity=0x%lx (%s) nfs_flags=0x%lx (%s)",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
 			__entry->type,
-			nfs_show_file_type(__entry->type),
+			show_fs_dirent_type(__entry->type),
 			(unsigned long long)__entry->version,
 			(long long)__entry->size,
 			__entry->cache_validity,
@@ -209,6 +162,7 @@
 DEFINE_NFS_INODE_EVENT(nfs_fsync_enter);
 DEFINE_NFS_INODE_EVENT_DONE(nfs_fsync_exit);
 DEFINE_NFS_INODE_EVENT(nfs_access_enter);
+DEFINE_NFS_INODE_EVENT_DONE(nfs_set_cache_invalid);
 
 TRACE_EVENT(nfs_access_exit,
 		TP_PROTO(
@@ -254,12 +208,12 @@
 			"type=%u (%s) version=%llu size=%lld "
 			"cache_validity=0x%lx (%s) nfs_flags=0x%lx (%s) "
 			"mask=0x%x permitted=0x%x",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
 			__entry->type,
-			nfs_show_file_type(__entry->type),
+			show_fs_dirent_type(__entry->type),
 			(unsigned long long)__entry->version,
 			(long long)__entry->size,
 			__entry->cache_validity,
@@ -270,34 +224,6 @@
 		)
 );
 
-TRACE_DEFINE_ENUM(LOOKUP_FOLLOW);
-TRACE_DEFINE_ENUM(LOOKUP_DIRECTORY);
-TRACE_DEFINE_ENUM(LOOKUP_AUTOMOUNT);
-TRACE_DEFINE_ENUM(LOOKUP_PARENT);
-TRACE_DEFINE_ENUM(LOOKUP_REVAL);
-TRACE_DEFINE_ENUM(LOOKUP_RCU);
-TRACE_DEFINE_ENUM(LOOKUP_OPEN);
-TRACE_DEFINE_ENUM(LOOKUP_CREATE);
-TRACE_DEFINE_ENUM(LOOKUP_EXCL);
-TRACE_DEFINE_ENUM(LOOKUP_RENAME_TARGET);
-TRACE_DEFINE_ENUM(LOOKUP_EMPTY);
-TRACE_DEFINE_ENUM(LOOKUP_DOWN);
-
-#define show_lookup_flags(flags) \
-	__print_flags(flags, "|", \
-			{ LOOKUP_FOLLOW, "FOLLOW" }, \
-			{ LOOKUP_DIRECTORY, "DIRECTORY" }, \
-			{ LOOKUP_AUTOMOUNT, "AUTOMOUNT" }, \
-			{ LOOKUP_PARENT, "PARENT" }, \
-			{ LOOKUP_REVAL, "REVAL" }, \
-			{ LOOKUP_RCU, "RCU" }, \
-			{ LOOKUP_OPEN, "OPEN" }, \
-			{ LOOKUP_CREATE, "CREATE" }, \
-			{ LOOKUP_EXCL, "EXCL" }, \
-			{ LOOKUP_RENAME_TARGET, "RENAME_TARGET" }, \
-			{ LOOKUP_EMPTY, "EMPTY" }, \
-			{ LOOKUP_DOWN, "DOWN" })
-
 DECLARE_EVENT_CLASS(nfs_lookup_event,
 		TP_PROTO(
 			const struct inode *dir,
@@ -324,7 +250,7 @@
 		TP_printk(
 			"flags=0x%lx (%s) name=%02x:%02x:%llu/%s",
 			__entry->flags,
-			show_lookup_flags(__entry->flags),
+			show_fs_lookup_flags(__entry->flags),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -368,9 +294,9 @@
 
 		TP_printk(
 			"error=%ld (%s) flags=0x%lx (%s) name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			__entry->flags,
-			show_lookup_flags(__entry->flags),
+			show_fs_lookup_flags(__entry->flags),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -392,46 +318,6 @@
 DEFINE_NFS_LOOKUP_EVENT(nfs_lookup_revalidate_enter);
 DEFINE_NFS_LOOKUP_EVENT_DONE(nfs_lookup_revalidate_exit);
 
-TRACE_DEFINE_ENUM(O_WRONLY);
-TRACE_DEFINE_ENUM(O_RDWR);
-TRACE_DEFINE_ENUM(O_CREAT);
-TRACE_DEFINE_ENUM(O_EXCL);
-TRACE_DEFINE_ENUM(O_NOCTTY);
-TRACE_DEFINE_ENUM(O_TRUNC);
-TRACE_DEFINE_ENUM(O_APPEND);
-TRACE_DEFINE_ENUM(O_NONBLOCK);
-TRACE_DEFINE_ENUM(O_DSYNC);
-TRACE_DEFINE_ENUM(O_DIRECT);
-TRACE_DEFINE_ENUM(O_LARGEFILE);
-TRACE_DEFINE_ENUM(O_DIRECTORY);
-TRACE_DEFINE_ENUM(O_NOFOLLOW);
-TRACE_DEFINE_ENUM(O_NOATIME);
-TRACE_DEFINE_ENUM(O_CLOEXEC);
-
-#define show_open_flags(flags) \
-	__print_flags(flags, "|", \
-		{ O_WRONLY, "O_WRONLY" }, \
-		{ O_RDWR, "O_RDWR" }, \
-		{ O_CREAT, "O_CREAT" }, \
-		{ O_EXCL, "O_EXCL" }, \
-		{ O_NOCTTY, "O_NOCTTY" }, \
-		{ O_TRUNC, "O_TRUNC" }, \
-		{ O_APPEND, "O_APPEND" }, \
-		{ O_NONBLOCK, "O_NONBLOCK" }, \
-		{ O_DSYNC, "O_DSYNC" }, \
-		{ O_DIRECT, "O_DIRECT" }, \
-		{ O_LARGEFILE, "O_LARGEFILE" }, \
-		{ O_DIRECTORY, "O_DIRECTORY" }, \
-		{ O_NOFOLLOW, "O_NOFOLLOW" }, \
-		{ O_NOATIME, "O_NOATIME" }, \
-		{ O_CLOEXEC, "O_CLOEXEC" })
-
-#define show_fmode_flags(mode) \
-	__print_flags(mode, "|", \
-		{ ((__force unsigned long)FMODE_READ), "READ" }, \
-		{ ((__force unsigned long)FMODE_WRITE), "WRITE" }, \
-		{ ((__force unsigned long)FMODE_EXEC), "EXEC" })
-
 TRACE_EVENT(nfs_atomic_open_enter,
 		TP_PROTO(
 			const struct inode *dir,
@@ -443,7 +329,7 @@
 
 		TP_STRUCT__entry(
 			__field(unsigned long, flags)
-			__field(unsigned int, fmode)
+			__field(unsigned long, fmode)
 			__field(dev_t, dev)
 			__field(u64, dir)
 			__string(name, ctx->dentry->d_name.name)
@@ -453,15 +339,15 @@
 			__entry->dev = dir->i_sb->s_dev;
 			__entry->dir = NFS_FILEID(dir);
 			__entry->flags = flags;
-			__entry->fmode = (__force unsigned int)ctx->mode;
+			__entry->fmode = (__force unsigned long)ctx->mode;
 			__assign_str(name, ctx->dentry->d_name.name);
 		),
 
 		TP_printk(
 			"flags=0x%lx (%s) fmode=%s name=%02x:%02x:%llu/%s",
 			__entry->flags,
-			show_open_flags(__entry->flags),
-			show_fmode_flags(__entry->fmode),
+			show_fs_fcntl_open_flags(__entry->flags),
+			show_fs_fmode_flags(__entry->fmode),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -481,7 +367,7 @@
 		TP_STRUCT__entry(
 			__field(unsigned long, error)
 			__field(unsigned long, flags)
-			__field(unsigned int, fmode)
+			__field(unsigned long, fmode)
 			__field(dev_t, dev)
 			__field(u64, dir)
 			__string(name, ctx->dentry->d_name.name)
@@ -492,17 +378,17 @@
 			__entry->dev = dir->i_sb->s_dev;
 			__entry->dir = NFS_FILEID(dir);
 			__entry->flags = flags;
-			__entry->fmode = (__force unsigned int)ctx->mode;
+			__entry->fmode = (__force unsigned long)ctx->mode;
 			__assign_str(name, ctx->dentry->d_name.name);
 		),
 
 		TP_printk(
 			"error=%ld (%s) flags=0x%lx (%s) fmode=%s "
 			"name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			__entry->flags,
-			show_open_flags(__entry->flags),
-			show_fmode_flags(__entry->fmode),
+			show_fs_fcntl_open_flags(__entry->flags),
+			show_fs_fmode_flags(__entry->fmode),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -535,7 +421,7 @@
 		TP_printk(
 			"flags=0x%lx (%s) name=%02x:%02x:%llu/%s",
 			__entry->flags,
-			show_open_flags(__entry->flags),
+			show_fs_fcntl_open_flags(__entry->flags),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -570,9 +456,9 @@
 
 		TP_printk(
 			"error=%ld (%s) flags=0x%lx (%s) name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			__entry->flags,
-			show_open_flags(__entry->flags),
+			show_fs_fcntl_open_flags(__entry->flags),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -640,7 +526,7 @@
 
 		TP_printk(
 			"error=%ld (%s) name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -730,7 +616,7 @@
 
 		TP_printk(
 			"error=%ld (%s) fileid=%02x:%02x:%llu name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			__entry->fileid,
 			MAJOR(__entry->dev), MINOR(__entry->dev),
@@ -817,7 +703,7 @@
 		TP_printk(
 			"error=%ld (%s) old_name=%02x:%02x:%llu/%s "
 			"new_name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->old_dir,
 			__get_str(old_name),
@@ -871,7 +757,7 @@
 
 		TP_printk(
 			"error=%ld (%s) name=%02x:%02x:%llu/%s",
-			-__entry->error, nfs_show_status(__entry->error),
+			-__entry->error, show_nfs_status(__entry->error),
 			MAJOR(__entry->dev), MINOR(__entry->dev),
 			(unsigned long long)__entry->dir,
 			__get_str(name)
@@ -1054,16 +940,6 @@
 	)
 );
 
-TRACE_DEFINE_ENUM(NFS_UNSTABLE);
-TRACE_DEFINE_ENUM(NFS_DATA_SYNC);
-TRACE_DEFINE_ENUM(NFS_FILE_SYNC);
-
-#define nfs_show_stable(stable) \
-	__print_symbolic(stable, \
-			{ NFS_UNSTABLE, "UNSTABLE" }, \
-			{ NFS_DATA_SYNC, "DATA_SYNC" }, \
-			{ NFS_FILE_SYNC, "FILE_SYNC" })
-
 TRACE_EVENT(nfs_initiate_write,
 		TP_PROTO(
 			const struct nfs_pgio_header *hdr
@@ -1077,7 +953,7 @@
 			__field(u64, fileid)
 			__field(loff_t, offset)
 			__field(u32, count)
-			__field(enum nfs3_stable_how, stable)
+			__field(unsigned long, stable)
 		),
 
 		TP_fast_assign(
@@ -1101,7 +977,7 @@
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
 			(long long)__entry->offset, __entry->count,
-			nfs_show_stable(__entry->stable)
+			show_nfs_stable_how(__entry->stable)
 		)
 );
 
@@ -1121,7 +997,7 @@
 			__field(u32, arg_count)
 			__field(u32, res_count)
 			__field(int, status)
-			__field(enum nfs3_stable_how, stable)
+			__field(unsigned long, stable)
 			__array(char, verifier, NFS4_VERIFIER_SIZE)
 		),
 
@@ -1154,8 +1030,8 @@
 			__entry->fhandle,
 			(long long)__entry->offset, __entry->arg_count,
 			__entry->res_count, __entry->status,
-			nfs_show_stable(__entry->stable),
-			__print_hex_str(__entry->verifier, NFS4_VERIFIER_SIZE)
+			show_nfs_stable_how(__entry->stable),
+			show_nfs4_verifier(__entry->verifier)
 		)
 );
 
@@ -1256,7 +1132,7 @@
 			__field(u64, fileid)
 			__field(loff_t, offset)
 			__field(int, status)
-			__field(enum nfs3_stable_how, stable)
+			__field(unsigned long, stable)
 			__array(char, verifier, NFS4_VERIFIER_SIZE)
 		),
 
@@ -1285,8 +1161,8 @@
 			(unsigned long long)__entry->fileid,
 			__entry->fhandle,
 			(long long)__entry->offset, __entry->status,
-			nfs_show_stable(__entry->stable),
-			__print_hex_str(__entry->verifier, NFS4_VERIFIER_SIZE)
+			show_nfs_stable_how(__entry->stable),
+			show_nfs4_verifier(__entry->verifier)
 		)
 );
 
@@ -1323,76 +1199,6 @@
 		)
 );
 
-TRACE_DEFINE_ENUM(NFS_OK);
-TRACE_DEFINE_ENUM(NFSERR_PERM);
-TRACE_DEFINE_ENUM(NFSERR_NOENT);
-TRACE_DEFINE_ENUM(NFSERR_IO);
-TRACE_DEFINE_ENUM(NFSERR_NXIO);
-TRACE_DEFINE_ENUM(ECHILD);
-TRACE_DEFINE_ENUM(NFSERR_EAGAIN);
-TRACE_DEFINE_ENUM(NFSERR_ACCES);
-TRACE_DEFINE_ENUM(NFSERR_EXIST);
-TRACE_DEFINE_ENUM(NFSERR_XDEV);
-TRACE_DEFINE_ENUM(NFSERR_NODEV);
-TRACE_DEFINE_ENUM(NFSERR_NOTDIR);
-TRACE_DEFINE_ENUM(NFSERR_ISDIR);
-TRACE_DEFINE_ENUM(NFSERR_INVAL);
-TRACE_DEFINE_ENUM(NFSERR_FBIG);
-TRACE_DEFINE_ENUM(NFSERR_NOSPC);
-TRACE_DEFINE_ENUM(NFSERR_ROFS);
-TRACE_DEFINE_ENUM(NFSERR_MLINK);
-TRACE_DEFINE_ENUM(NFSERR_OPNOTSUPP);
-TRACE_DEFINE_ENUM(NFSERR_NAMETOOLONG);
-TRACE_DEFINE_ENUM(NFSERR_NOTEMPTY);
-TRACE_DEFINE_ENUM(NFSERR_DQUOT);
-TRACE_DEFINE_ENUM(NFSERR_STALE);
-TRACE_DEFINE_ENUM(NFSERR_REMOTE);
-TRACE_DEFINE_ENUM(NFSERR_WFLUSH);
-TRACE_DEFINE_ENUM(NFSERR_BADHANDLE);
-TRACE_DEFINE_ENUM(NFSERR_NOT_SYNC);
-TRACE_DEFINE_ENUM(NFSERR_BAD_COOKIE);
-TRACE_DEFINE_ENUM(NFSERR_NOTSUPP);
-TRACE_DEFINE_ENUM(NFSERR_TOOSMALL);
-TRACE_DEFINE_ENUM(NFSERR_SERVERFAULT);
-TRACE_DEFINE_ENUM(NFSERR_BADTYPE);
-TRACE_DEFINE_ENUM(NFSERR_JUKEBOX);
-
-#define nfs_show_status(x) \
-	__print_symbolic(x, \
-			{ NFS_OK, "OK" }, \
-			{ NFSERR_PERM, "PERM" }, \
-			{ NFSERR_NOENT, "NOENT" }, \
-			{ NFSERR_IO, "IO" }, \
-			{ NFSERR_NXIO, "NXIO" }, \
-			{ ECHILD, "CHILD" }, \
-			{ NFSERR_EAGAIN, "AGAIN" }, \
-			{ NFSERR_ACCES, "ACCES" }, \
-			{ NFSERR_EXIST, "EXIST" }, \
-			{ NFSERR_XDEV, "XDEV" }, \
-			{ NFSERR_NODEV, "NODEV" }, \
-			{ NFSERR_NOTDIR, "NOTDIR" }, \
-			{ NFSERR_ISDIR, "ISDIR" }, \
-			{ NFSERR_INVAL, "INVAL" }, \
-			{ NFSERR_FBIG, "FBIG" }, \
-			{ NFSERR_NOSPC, "NOSPC" }, \
-			{ NFSERR_ROFS, "ROFS" }, \
-			{ NFSERR_MLINK, "MLINK" }, \
-			{ NFSERR_OPNOTSUPP, "OPNOTSUPP" }, \
-			{ NFSERR_NAMETOOLONG, "NAMETOOLONG" }, \
-			{ NFSERR_NOTEMPTY, "NOTEMPTY" }, \
-			{ NFSERR_DQUOT, "DQUOT" }, \
-			{ NFSERR_STALE, "STALE" }, \
-			{ NFSERR_REMOTE, "REMOTE" }, \
-			{ NFSERR_WFLUSH, "WFLUSH" }, \
-			{ NFSERR_BADHANDLE, "BADHANDLE" }, \
-			{ NFSERR_NOT_SYNC, "NOTSYNC" }, \
-			{ NFSERR_BAD_COOKIE, "BADCOOKIE" }, \
-			{ NFSERR_NOTSUPP, "NOTSUPP" }, \
-			{ NFSERR_TOOSMALL, "TOOSMALL" }, \
-			{ NFSERR_SERVERFAULT, "REMOTEIO" }, \
-			{ NFSERR_BADTYPE, "BADTYPE" }, \
-			{ NFSERR_JUKEBOX, "JUKEBOX" })
-
 DECLARE_EVENT_CLASS(nfs_xdr_event,
 		TP_PROTO(
 			const struct xdr_stream *xdr,
@@ -1427,12 +1233,12 @@
 			__assign_str(procedure, task->tk_msg.rpc_proc->p_name);
 		),
 
-		TP_printk(
-			"task:%u@%d xid=0x%08x %sv%d %s error=%ld (%s)",
+		TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+			  " xid=0x%08x %sv%d %s error=%ld (%s)",
 			__entry->task_id, __entry->client_id, __entry->xid,
 			__get_str(program), __entry->version,
 			__get_str(procedure), -__entry->error,
-			nfs_show_status(__entry->error)
+			show_nfs_status(__entry->error)
 		)
 );
 #define DEFINE_NFS_XDR_EVENT(name) \
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/pagelist.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/pagelist.c
@@ -90,10 +90,10 @@
 	}
 }
 
-static inline struct nfs_page *
-nfs_page_alloc(void)
+static inline struct nfs_page *nfs_page_alloc(void)
 {
-	struct nfs_page	*p = kmem_cache_zalloc(nfs_page_cachep, GFP_KERNEL);
+	struct nfs_page *p =
+		kmem_cache_zalloc(nfs_page_cachep, nfs_io_gfp_mask());
 	if (p)
 		INIT_LIST_HEAD(&p->wb_list);
 	return p;
@@ -773,6 +773,9 @@
 		.flags = RPC_TASK_ASYNC | flags,
 	};
 
+	if (nfs_server_capable(hdr->inode, NFS_CAP_MOVEABLE))
+		task_setup_data.flags |= RPC_TASK_MOVEABLE;
+
 	hdr->rw_ops->rw_initiate(hdr, &msg, rpc_ops, &task_setup_data, how);
 
 	dprintk("NFS: initiated pgio call "
@@ -901,7 +904,7 @@
 	struct nfs_commit_info cinfo;
 	struct nfs_page_array *pg_array = &hdr->page_array;
 	unsigned int pagecount, pageused;
-	gfp_t gfp_flags = GFP_KERNEL;
+	gfp_t gfp_flags = nfs_io_gfp_mask();
 
 	pagecount = nfs_page_array_len(mirror->pg_base, mirror->pg_count);
 	pg_array->npages = pagecount;
@@ -988,7 +991,7 @@
 	desc->pg_mirrors_dynamic = NULL;
 	if (mirror_count == 1)
 		return desc->pg_mirrors_static;
-	ret = kmalloc_array(mirror_count, sizeof(*ret), GFP_KERNEL);
+	ret = kmalloc_array(mirror_count, sizeof(*ret), nfs_io_gfp_mask());
 	if (ret != NULL) {
 		for (i = 0; i < mirror_count; i++)
 			nfs_pageio_mirror_init(&ret[i], desc->pg_bsize);
@@ -1227,6 +1230,7 @@
 
 	do {
 		list_splice_init(&mirror->pg_list, &head);
+		mirror->pg_recoalesce = 0;
 
 		while (!list_empty(&head)) {
 			struct nfs_page *req;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/pnfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/pnfs.c
@@ -92,6 +92,17 @@
 	return local;
 }
 
+const struct pnfs_layoutdriver_type *pnfs_find_layoutdriver(u32 id)
+{
+	return find_pnfs_driver(id);
+}
+
+void pnfs_put_layoutdriver(const struct pnfs_layoutdriver_type *ld)
+{
+	if (ld)
+		module_put(ld->owner);
+}
+
 void
 unset_pnfs_layoutdriver(struct nfs_server *nfss)
 {
@@ -458,6 +469,7 @@
 		pnfs_clear_lseg_state(lseg, lseg_list);
 	pnfs_clear_layoutreturn_info(lo);
 	pnfs_free_returned_lsegs(lo, lseg_list, &range, 0);
+	set_bit(NFS_LAYOUT_DRAIN, &lo->plh_flags);
 	if (test_bit(NFS_LAYOUT_RETURN, &lo->plh_flags) &&
 	    !test_and_set_bit(NFS_LAYOUT_RETURN_LOCK, &lo->plh_flags))
 		pnfs_clear_layoutreturn_waitbit(lo);
@@ -1157,10 +1169,9 @@
 	LIST_HEAD(freeme);
 
 	spin_lock(&inode->i_lock);
-	if (!pnfs_layout_is_valid(lo) ||
-	    !nfs4_stateid_match_other(&lo->plh_stateid, arg_stateid))
+	if (!nfs4_stateid_match_other(&lo->plh_stateid, arg_stateid))
 		goto out_unlock;
-	if (stateid) {
+	if (stateid && pnfs_layout_is_valid(lo)) {
 		u32 seq = be32_to_cpu(arg_stateid->seqid);
 
 		pnfs_mark_matching_lsegs_invalid(lo, &freeme, range, seq);
@@ -1182,7 +1193,7 @@
 		enum pnfs_iomode *iomode)
 {
 	/* Serialise LAYOUTGET/LAYOUTRETURN */
-	if (atomic_read(&lo->plh_outstanding) != 0)
+	if (atomic_read(&lo->plh_outstanding) != 0 && lo->plh_return_seq == 0)
 		return false;
 	if (test_and_set_bit(NFS_LAYOUT_RETURN_LOCK, &lo->plh_flags))
 		return false;
@@ -1233,7 +1244,7 @@
 	int status = 0;
 
 	*pcred = NULL;
-	lrp = kzalloc(sizeof(*lrp), GFP_NOFS);
+	lrp = kzalloc(sizeof(*lrp), GFP_KERNEL);
 	if (unlikely(lrp == NULL)) {
 		status = -ENOMEM;
 		spin_lock(&ino->i_lock);
@@ -1906,8 +1917,9 @@
 
 static void nfs_layoutget_end(struct pnfs_layout_hdr *lo)
 {
-	if (atomic_dec_and_test(&lo->plh_outstanding))
-		wake_up_var(&lo->plh_outstanding);
+	if (atomic_dec_and_test(&lo->plh_outstanding) &&
+	    test_and_clear_bit(NFS_LAYOUT_DRAIN, &lo->plh_flags))
+		wake_up_bit(&lo->plh_flags, NFS_LAYOUT_DRAIN);
 }
 
 static bool pnfs_is_first_layoutget(struct pnfs_layout_hdr *lo)
@@ -1981,6 +1993,14 @@
 	}
 
 lookup_again:
+	if (!nfs4_valid_open_stateid(ctx->state)) {
+		trace_pnfs_update_layout(ino, pos, count,
+					 iomode, lo, lseg,
+					 PNFS_UPDATE_LAYOUT_INVALID_OPEN);
+		lseg = ERR_PTR(-EIO);
+		goto out;
+	}
+
 	lseg = ERR_PTR(nfs4_client_recover_expired_lease(clp));
 	if (IS_ERR(lseg))
 		goto out;
@@ -1989,6 +2009,7 @@
 	lo = pnfs_find_alloc_layout(ino, ctx, gfp_flags);
 	if (lo == NULL) {
 		spin_unlock(&ino->i_lock);
+		lseg = ERR_PTR(-ENOMEM);
 		trace_pnfs_update_layout(ino, pos, count, iomode, lo, lseg,
 				 PNFS_UPDATE_LAYOUT_NOMEM);
 		goto out;
@@ -2013,11 +2034,11 @@
 	 * If the layout segment list is empty, but there are outstanding
 	 * layoutget calls, then they might be subject to a layoutrecall.
 	 */
-	if ((list_empty(&lo->plh_segs) || !pnfs_layout_is_valid(lo)) &&
+	if (test_bit(NFS_LAYOUT_DRAIN, &lo->plh_flags) &&
 	    atomic_read(&lo->plh_outstanding) != 0) {
 		spin_unlock(&ino->i_lock);
-		lseg = ERR_PTR(wait_var_event_killable(&lo->plh_outstanding,
-					!atomic_read(&lo->plh_outstanding)));
+		lseg = ERR_PTR(wait_on_bit(&lo->plh_flags, NFS_LAYOUT_DRAIN,
+					   TASK_KILLABLE));
 		if (IS_ERR(lseg))
 			goto out_put_layout_hdr;
 		pnfs_put_layout_hdr(lo);
@@ -2117,6 +2138,7 @@
 
 	lgp = pnfs_alloc_init_layoutget_args(ino, ctx, &stateid, &arg, gfp_flags);
 	if (!lgp) {
+		lseg = ERR_PTR(-ENOMEM);
 		trace_pnfs_update_layout(ino, pos, count, iomode, lo, NULL,
 					 PNFS_UPDATE_LAYOUT_NOMEM);
 		nfs_layoutget_end(lo);
@@ -2139,6 +2161,12 @@
 		case -ERECALLCONFLICT:
 		case -EAGAIN:
 			break;
+		case -ENODATA:
+			/* The server returned NFS4ERR_LAYOUTUNAVAILABLE */
+			pnfs_layout_set_fail_bit(
+				lo, pnfs_iomode_to_fail_bit(iomode));
+			lseg = NULL;
+			goto out_put_layout_hdr;
 		default:
 			if (!nfs_error_is_fatal(PTR_ERR(lseg))) {
 				pnfs_layout_clear_fail_bit(lo, pnfs_iomode_to_fail_bit(iomode));
@@ -2394,7 +2422,8 @@
 		goto out_forget;
 	}
 
-	if (!pnfs_layout_is_valid(lo) && !pnfs_is_first_layoutget(lo))
+	if (test_bit(NFS_LAYOUT_DRAIN, &lo->plh_flags) &&
+	    !pnfs_is_first_layoutget(lo))
 		goto out_forget;
 
 	if (nfs4_stateid_match_other(&lo->plh_stateid, &res->stateid)) {
@@ -2607,31 +2636,44 @@
 	return mode == 0;
 }
 
-static int
-pnfs_layout_return_unused_byserver(struct nfs_server *server, void *data)
+static int pnfs_layout_return_unused_byserver(struct nfs_server *server,
+					      void *data)
 {
 	const struct pnfs_layout_range *range = data;
+	const struct cred *cred;
 	struct pnfs_layout_hdr *lo;
 	struct inode *inode;
+	nfs4_stateid stateid;
+	enum pnfs_iomode iomode;
+
 restart:
 	rcu_read_lock();
 	list_for_each_entry_rcu(lo, &server->layouts, plh_layouts) {
-		if (!pnfs_layout_can_be_returned(lo) ||
+		inode = lo->plh_inode;
+		if (!inode || !pnfs_layout_can_be_returned(lo) ||
 		    test_bit(NFS_LAYOUT_RETURN_REQUESTED, &lo->plh_flags))
 			continue;
-		inode = lo->plh_inode;
 		spin_lock(&inode->i_lock);
-		if (!pnfs_should_return_unused_layout(lo, range)) {
+		if (!lo->plh_inode ||
+		    !pnfs_should_return_unused_layout(lo, range)) {
 			spin_unlock(&inode->i_lock);
 			continue;
 		}
+		pnfs_get_layout_hdr(lo);
+		pnfs_set_plh_return_info(lo, range->iomode, 0);
+		if (pnfs_mark_matching_lsegs_return(lo, &lo->plh_return_segs,
+						    range, 0) != 0 ||
+		    !pnfs_prepare_layoutreturn(lo, &stateid, &cred, &iomode)) {
+			spin_unlock(&inode->i_lock);
+			rcu_read_unlock();
+			pnfs_put_layout_hdr(lo);
+			cond_resched();
+			goto restart;
+		}
 		spin_unlock(&inode->i_lock);
-		inode = pnfs_grab_inode_layout_hdr(lo);
-		if (!inode)
-			continue;
 		rcu_read_unlock();
-		pnfs_mark_layout_for_return(inode, range);
-		iput(inode);
+		pnfs_send_layoutreturn(lo, &stateid, &cred, iomode, false);
+		pnfs_put_layout_hdr(lo);
 		cond_resched();
 		goto restart;
 	}
@@ -3250,7 +3292,7 @@
 {
 	struct nfs4_threshold *thp;
 
-	thp = kzalloc(sizeof(*thp), GFP_NOFS);
+	thp = kzalloc(sizeof(*thp), GFP_KERNEL);
 	if (!thp) {
 		dprintk("%s mdsthreshold allocation failed\n", __func__);
 		return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/pnfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/pnfs.h
@@ -82,10 +82,6 @@
 	PNFS_TRY_AGAIN     = 2,
 };
 
-/* error codes for internal use */
-#define NFS4ERR_RESET_TO_MDS   12001
-#define NFS4ERR_RESET_TO_PNFS  12002
-
 #ifdef CONFIG_NFS_V4_1
 
 #define LAYOUT_NFSV4_1_MODULE_PREFIX "nfs-layouttype4"
@@ -109,6 +105,7 @@
 	NFS_LAYOUT_FIRST_LAYOUTGET,	/* Serialize first layoutget */
 	NFS_LAYOUT_INODE_FREEING,	/* The inode is being freed */
 	NFS_LAYOUT_HASHED,		/* The layout visible */
+	NFS_LAYOUT_DRAIN,
 };
 
 enum layoutdriver_policy_flags {
@@ -238,6 +235,8 @@
 
 extern int pnfs_register_layoutdriver(struct pnfs_layoutdriver_type *);
 extern void pnfs_unregister_layoutdriver(struct pnfs_layoutdriver_type *);
+extern const struct pnfs_layoutdriver_type *pnfs_find_layoutdriver(u32 id);
+extern void pnfs_put_layoutdriver(const struct pnfs_layoutdriver_type *ld);
 
 /* nfs4proc.c */
 extern size_t max_response_pages(struct nfs_server *server);
@@ -517,7 +516,7 @@
 {
 	struct pnfs_ds_commit_info *fl_cinfo = cinfo->ds;
 
-	if (!lseg || !fl_cinfo->ops->mark_request_commit)
+	if (!lseg || !fl_cinfo->ops || !fl_cinfo->ops->mark_request_commit)
 		return false;
 	fl_cinfo->ops->mark_request_commit(req, lseg, cinfo, ds_commit_idx);
 	return true;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/pnfs_dev.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/pnfs_dev.c
@@ -154,7 +154,7 @@
 		set_bit(NFS_DEVICEID_NOCACHE, &d->flags);
 
 out_free_pages:
-	for (i = 0; i < max_pages; i++)
+	while (--i >= 0)
 		__free_page(pages[i]);
 	kfree(pages);
 out_free_pdev:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/pnfs_nfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/pnfs_nfs.c
@@ -419,7 +419,7 @@
 pnfs_bucket_fetch_commitdata(struct pnfs_commit_bucket *bucket,
 			     struct nfs_commit_info *cinfo)
 {
-	struct nfs_commit_data *data = nfs_commitdata_alloc(false);
+	struct nfs_commit_data *data = nfs_commitdata_alloc();
 
 	if (!data)
 		return NULL;
@@ -468,7 +468,6 @@
 				goto out_error;
 			data->ds_commit_index = i;
 			list_add_tail(&data->list, list);
-			atomic_inc(&cinfo->mds->rpcs_out);
 			nreq++;
 		}
 		mutex_unlock(&NFS_I(cinfo->inode)->commit_mutex);
@@ -516,11 +515,14 @@
 	unsigned int nreq = 0;
 
 	if (!list_empty(mds_pages)) {
-		data = nfs_commitdata_alloc(true);
+		data = nfs_commitdata_alloc();
+		if (!data) {
+			nfs_retry_commit(mds_pages, NULL, cinfo, -1);
+			return -ENOMEM;
+		}
 		data->ds_commit_index = -1;
 		list_splice_init(mds_pages, &data->pages);
 		list_add_tail(&data->list, &list);
-		atomic_inc(&cinfo->mds->rpcs_out);
 		nreq++;
 	}
 
@@ -895,7 +897,7 @@
 	}
 
 	smp_wmb();
-	ds->ds_clp = clp;
+	WRITE_ONCE(ds->ds_clp, clp);
 	dprintk("%s [new] addr: %s\n", __func__, ds->ds_remotestr);
 out:
 	return status;
@@ -941,7 +943,7 @@
 			* Test this address for session trunking and
 			* add as an alias
 			*/
-			xprtdata.cred = nfs4_get_clid_cred(clp),
+			xprtdata.cred = nfs4_get_clid_cred(clp);
 			rpc_clnt_add_xprt(clp->cl_rpcclient, &xprt_args,
 					  rpc_clnt_setup_test_and_add_xprt,
 					  &rpcdata);
@@ -973,7 +975,7 @@
 	}
 
 	smp_wmb();
-	ds->ds_clp = clp;
+	WRITE_ONCE(ds->ds_clp, clp);
 	dprintk("%s [new] addr: %s\n", __func__, ds->ds_remotestr);
 out:
 	return status;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/proc.c
@@ -91,7 +91,8 @@
 	info->dtpref = fsinfo.tsize;
 	info->maxfilesize = 0x7FFFFFFF;
 	info->lease_time = 0;
-	info->change_attr_type = NFS4_CHANGE_TYPE_IS_TIME_METADATA;
+	info->change_attr_type = NFS4_CHANGE_TYPE_IS_UNDEFINED;
+	info->xattr_support = 0;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/read.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/read.c
@@ -120,12 +120,8 @@
 	if (nfs_error_is_fatal_on_server(error) && error != -ETIMEDOUT)
 		SetPageError(page);
 	if (nfs_page_group_sync_on_bit(req, PG_UNLOCKPAGE)) {
-		struct address_space *mapping = page_file_mapping(page);
-
 		if (PageUptodate(page))
 			nfs_readpage_to_fscache(inode, page, 0);
-		else if (!PageError(page) && !PagePrivate(page))
-			generic_error_remove_page(mapping, page);
 		unlock_page(page);
 	}
 	nfs_release_request(req);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/super.c
@@ -47,6 +47,7 @@
 #include <linux/vfs.h>
 #include <linux/inet.h>
 #include <linux/in6.h>
+#include <linux/sched.h>
 #include <linux/slab.h>
 #include <net/ipv6.h>
 #include <linux/netdevice.h>
@@ -219,6 +220,7 @@
 		ret = fn(server, data);
 		if (ret)
 			goto out;
+		cond_resched();
 		rcu_read_lock();
 	}
 	rcu_read_unlock();
@@ -865,7 +867,15 @@
 	 * Now ask the mount server to map our export path
 	 * to a file handle.
 	 */
-	status = nfs_mount(&request, ctx->timeo, ctx->retrans);
+	if ((request.protocol == XPRT_TRANSPORT_UDP) ==
+	    !(ctx->flags & NFS_MOUNT_TCP))
+		/*
+		 * NFS protocol and mount protocol are both UDP or neither UDP
+		 * so timeouts are compatible.  Use NFS timeouts for MOUNT
+		 */
+		status = nfs_mount(&request, ctx->timeo, ctx->retrans);
+	else
+		status = nfs_mount(&request, NFS_UNSPEC_TIMEO, NFS_UNSPEC_RETRANS);
 	if (status != 0) {
 		dfprintk(MOUNT, "NFS: unable to mount server %s, error %d\n",
 				request.hostname, status);
@@ -1046,22 +1056,31 @@
 	if (ctx->bsize)
 		sb->s_blocksize = nfs_block_size(ctx->bsize, &sb->s_blocksize_bits);
 
-	if (server->nfs_client->rpc_ops->version != 2) {
-		/* The VFS shouldn't apply the umask to mode bits. We will do
-		 * so ourselves when necessary.
+	switch (server->nfs_client->rpc_ops->version) {
+	case 2:
+		sb->s_time_gran = 1000;
+		sb->s_time_min = 0;
+		sb->s_time_max = U32_MAX;
+		break;
+	case 3:
+		/*
+		 * The VFS shouldn't apply the umask to mode bits.
+		 * We will do so ourselves when necessary.
 		 */
 		sb->s_flags |= SB_POSIXACL;
 		sb->s_time_gran = 1;
-		sb->s_export_op = &nfs_export_ops;
-	} else
-		sb->s_time_gran = 1000;
-
-	if (server->nfs_client->rpc_ops->version != 4) {
 		sb->s_time_min = 0;
 		sb->s_time_max = U32_MAX;
-	} else {
+		sb->s_export_op = &nfs_export_ops;
+		break;
+	case 4:
+		sb->s_flags |= SB_POSIXACL;
+		sb->s_time_gran = 1;
 		sb->s_time_min = S64_MIN;
 		sb->s_time_max = S64_MAX;
+		if (server->caps & NFS_CAP_ATOMIC_OPEN_V1)
+			sb->s_export_op = &nfs_export_ops;
+		break;
 	}
 
 	sb->s_magic = NFS_SUPER_MAGIC;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/sysfs.c
@@ -18,7 +18,7 @@
 #include "sysfs.h"
 
 struct kobject *nfs_client_kobj;
-static struct kset *nfs_client_kset;
+static struct kset *nfs_kset;
 
 static void nfs_netns_object_release(struct kobject *kobj)
 {
@@ -55,13 +55,13 @@
 
 int nfs_sysfs_init(void)
 {
-	nfs_client_kset = kset_create_and_add("nfs", NULL, fs_kobj);
-	if (!nfs_client_kset)
+	nfs_kset = kset_create_and_add("nfs", NULL, fs_kobj);
+	if (!nfs_kset)
 		return -ENOMEM;
-	nfs_client_kobj = nfs_netns_object_alloc("net", nfs_client_kset, NULL);
+	nfs_client_kobj = nfs_netns_object_alloc("net", nfs_kset, NULL);
 	if  (!nfs_client_kobj) {
-		kset_unregister(nfs_client_kset);
-		nfs_client_kset = NULL;
+		kset_unregister(nfs_kset);
+		nfs_kset = NULL;
 		return -ENOMEM;
 	}
 	return 0;
@@ -70,7 +70,7 @@
 void nfs_sysfs_exit(void)
 {
 	kobject_put(nfs_client_kobj);
-	kset_unregister(nfs_client_kset);
+	kset_unregister(nfs_kset);
 }
 
 static ssize_t nfs_netns_identifier_show(struct kobject *kobj,
@@ -158,7 +158,7 @@
 	p = kzalloc(sizeof(*p), GFP_KERNEL);
 	if (p) {
 		p->net = net;
-		p->kobject.kset = nfs_client_kset;
+		p->kobject.kset = nfs_kset;
 		if (kobject_init_and_add(&p->kobject, &nfs_netns_client_type,
 					parent, "nfs_client") == 0)
 			return p;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/unlink.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/unlink.c
@@ -102,6 +102,10 @@
 	};
 	struct rpc_task *task;
 	struct inode *dir = d_inode(data->dentry->d_parent);
+
+	if (nfs_server_capable(inode, NFS_CAP_MOVEABLE))
+		task_setup_data.flags |= RPC_TASK_MOVEABLE;
+
 	nfs_sb_active(dir->i_sb);
 	data->args.fh = NFS_FH(dir);
 	nfs_fattr_init(data->res.dir_attr);
@@ -344,6 +348,10 @@
 		.flags = RPC_TASK_ASYNC | RPC_TASK_CRED_NOREF,
 	};
 
+	if (nfs_server_capable(old_dir, NFS_CAP_MOVEABLE) &&
+	    nfs_server_capable(new_dir, NFS_CAP_MOVEABLE))
+		task_setup_data.flags |= RPC_TASK_MOVEABLE;
+
 	data = kzalloc(sizeof(*data), GFP_KERNEL);
 	if (data == NULL)
 		return ERR_PTR(-ENOMEM);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfs/write.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfs/write.c
@@ -58,7 +58,8 @@
 static const struct nfs_commit_completion_ops nfs_commit_completion_ops;
 static const struct nfs_rw_ops nfs_rw_write_ops;
 static void nfs_inode_remove_request(struct nfs_page *req);
-static void nfs_clear_request_commit(struct nfs_page *req);
+static void nfs_clear_request_commit(struct nfs_commit_info *cinfo,
+				     struct nfs_page *req);
 static void nfs_init_cinfo_from_inode(struct nfs_commit_info *cinfo,
 				      struct inode *inode);
 static struct nfs_page *
@@ -70,27 +71,17 @@
 static struct kmem_cache *nfs_cdata_cachep;
 static mempool_t *nfs_commit_mempool;
 
-struct nfs_commit_data *nfs_commitdata_alloc(bool never_fail)
+struct nfs_commit_data *nfs_commitdata_alloc(void)
 {
 	struct nfs_commit_data *p;
 
-	if (never_fail)
-		p = mempool_alloc(nfs_commit_mempool, GFP_NOIO);
-	else {
-		/* It is OK to do some reclaim, not no safe to wait
-		 * for anything to be returned to the pool.
-		 * mempool_alloc() cannot handle that particular combination,
-		 * so we need two separate attempts.
-		 */
+	p = kmem_cache_zalloc(nfs_cdata_cachep, nfs_io_gfp_mask());
+	if (!p) {
 		p = mempool_alloc(nfs_commit_mempool, GFP_NOWAIT);
 		if (!p)
-			p = kmem_cache_alloc(nfs_cdata_cachep, GFP_NOIO |
-					     __GFP_NOWARN | __GFP_NORETRY);
-		if (!p)
 			return NULL;
+		memset(p, 0, sizeof(*p));
 	}
-
-	memset(p, 0, sizeof(*p));
 	INIT_LIST_HEAD(&p->pages);
 	return p;
 }
@@ -104,9 +95,15 @@
 
 static struct nfs_pgio_header *nfs_writehdr_alloc(void)
 {
-	struct nfs_pgio_header *p = mempool_alloc(nfs_wdata_mempool, GFP_KERNEL);
+	struct nfs_pgio_header *p;
 
-	memset(p, 0, sizeof(*p));
+	p = kmem_cache_zalloc(nfs_wdata_cachep, nfs_io_gfp_mask());
+	if (!p) {
+		p = mempool_alloc(nfs_wdata_mempool, GFP_NOWAIT);
+		if (!p)
+			return NULL;
+		memset(p, 0, sizeof(*p));
+	}
 	p->rw_mode = FMODE_WRITE;
 	return p;
 }
@@ -314,7 +311,10 @@
 	struct address_space *mapping = page_file_mapping(page);
 
 	SetPageError(page);
-	mapping_set_error(mapping, error);
+	filemap_set_wb_err(mapping, error);
+	if (mapping->host)
+		errseq_set(&mapping->host->i_sb->s_wb_err,
+			   error == -ENOSPC ? -ENOSPC : -EIO);
 	nfs_set_pageerror(mapping);
 }
 
@@ -501,8 +501,8 @@
  * the (former) group.  All subrequests are removed from any write or commit
  * lists, unlinked from the group and destroyed.
  */
-void
-nfs_join_page_group(struct nfs_page *head, struct inode *inode)
+void nfs_join_page_group(struct nfs_page *head, struct nfs_commit_info *cinfo,
+			 struct inode *inode)
 {
 	struct nfs_page *subreq;
 	struct nfs_page *destroy_list = NULL;
@@ -532,7 +532,7 @@
 	 * Commit list removal accounting is done after locks are dropped */
 	subreq = head;
 	do {
-		nfs_clear_request_commit(subreq);
+		nfs_clear_request_commit(cinfo, subreq);
 		subreq = subreq->wb_this_page;
 	} while (subreq != head);
 
@@ -566,8 +566,10 @@
 {
 	struct inode *inode = page_file_mapping(page)->host;
 	struct nfs_page *head;
+	struct nfs_commit_info cinfo;
 	int ret;
 
+	nfs_init_cinfo_from_inode(&cinfo, inode);
 	/*
 	 * A reference is taken only on the head request which acts as a
 	 * reference to the whole page group - the group will not be destroyed
@@ -584,7 +586,7 @@
 		return ERR_PTR(ret);
 	}
 
-	nfs_join_page_group(head, inode);
+	nfs_join_page_group(head, &cinfo, inode);
 
 	return head;
 }
@@ -602,8 +604,9 @@
  * Find an associated nfs write request, and prepare to flush it out
  * May return an error if the user signalled nfs_wait_on_request().
  */
-static int nfs_page_async_flush(struct nfs_pageio_descriptor *pgio,
-				struct page *page)
+static int nfs_page_async_flush(struct page *page,
+				struct writeback_control *wbc,
+				struct nfs_pageio_descriptor *pgio)
 {
 	struct nfs_page *req;
 	int ret = 0;
@@ -629,11 +632,11 @@
 		/*
 		 * Remove the problematic req upon fatal errors on the server
 		 */
-		if (nfs_error_is_fatal(ret)) {
-			if (nfs_error_is_fatal_on_server(ret))
-				goto out_launder;
-		} else
-			ret = -EAGAIN;
+		if (nfs_error_is_fatal_on_server(ret))
+			goto out_launder;
+		if (wbc->sync_mode == WB_SYNC_NONE)
+			ret = AOP_WRITEPAGE_ACTIVATE;
+		redirty_page_for_writepage(wbc, page);
 		nfs_redirty_request(req);
 		pgio->pg_error = 0;
 	} else
@@ -649,15 +652,8 @@
 static int nfs_do_writepage(struct page *page, struct writeback_control *wbc,
 			    struct nfs_pageio_descriptor *pgio)
 {
-	int ret;
-
 	nfs_pageio_cond_complete(pgio, page_index(page));
-	ret = nfs_page_async_flush(pgio, page);
-	if (ret == -EAGAIN) {
-		redirty_page_for_writepage(wbc, page);
-		ret = AOP_WRITEPAGE_ACTIVATE;
-	}
-	return ret;
+	return nfs_page_async_flush(page, wbc, pgio);
 }
 
 /*
@@ -676,11 +672,7 @@
 	err = nfs_do_writepage(page, wbc, &pgio);
 	pgio.pg_error = 0;
 	nfs_pageio_complete(&pgio);
-	if (err < 0)
-		return err;
-	if (nfs_error_is_fatal(pgio.pg_error))
-		return pgio.pg_error;
-	return 0;
+	return err;
 }
 
 int nfs_writepage(struct page *page, struct writeback_control *wbc)
@@ -728,19 +720,19 @@
 		priority = wb_priority(wbc);
 	}
 
-	nfs_pageio_init_write(&pgio, inode, priority, false,
-				&nfs_async_write_completion_ops);
-	pgio.pg_io_completion = ioc;
-	err = write_cache_pages(mapping, wbc, nfs_writepages_callback, &pgio);
-	pgio.pg_error = 0;
-	nfs_pageio_complete(&pgio);
+	do {
+		nfs_pageio_init_write(&pgio, inode, priority, false,
+				      &nfs_async_write_completion_ops);
+		pgio.pg_io_completion = ioc;
+		err = write_cache_pages(mapping, wbc, nfs_writepages_callback,
+					&pgio);
+		pgio.pg_error = 0;
+		nfs_pageio_complete(&pgio);
+	} while (err < 0 && !nfs_error_is_fatal(err));
 	nfs_io_completion_put(ioc);
 
 	if (err < 0)
 		goto out_err;
-	err = pgio.pg_error;
-	if (nfs_error_is_fatal(err))
-		goto out_err;
 	return 0;
 out_err:
 	return err;
@@ -956,18 +948,16 @@
 }
 
 /* Called holding the request lock on @req */
-static void
-nfs_clear_request_commit(struct nfs_page *req)
+static void nfs_clear_request_commit(struct nfs_commit_info *cinfo,
+				     struct nfs_page *req)
 {
 	if (test_bit(PG_CLEAN, &req->wb_flags)) {
 		struct nfs_open_context *ctx = nfs_req_openctx(req);
 		struct inode *inode = d_inode(ctx->dentry);
-		struct nfs_commit_info cinfo;
 
-		nfs_init_cinfo_from_inode(&cinfo, inode);
 		mutex_lock(&NFS_I(inode)->commit_mutex);
-		if (!pnfs_clear_request_commit(req, &cinfo)) {
-			nfs_request_remove_commit_list(req, &cinfo);
+		if (!pnfs_clear_request_commit(req, cinfo)) {
+			nfs_request_remove_commit_list(req, cinfo);
 		}
 		mutex_unlock(&NFS_I(inode)->commit_mutex);
 		nfs_clear_page_commit(req->wb_page);
@@ -1038,25 +1028,11 @@
 	struct nfs_page *req, *tmp;
 	int ret = 0;
 
-restart:
 	list_for_each_entry_safe(req, tmp, src, wb_list) {
 		kref_get(&req->wb_kref);
 		if (!nfs_lock_request(req)) {
-			int status;
-
-			/* Prevent deadlock with nfs_lock_and_join_requests */
-			if (!list_empty(dst)) {
-				nfs_release_request(req);
-				continue;
-			}
-			/* Ensure we make progress to prevent livelock */
-			mutex_unlock(&NFS_I(cinfo->inode)->commit_mutex);
-			status = nfs_wait_on_request(req);
 			nfs_release_request(req);
-			mutex_lock(&NFS_I(cinfo->inode)->commit_mutex);
-			if (status < 0)
-				break;
-			goto restart;
+			continue;
 		}
 		nfs_request_remove_commit_list(req, cinfo);
 		clear_bit(PG_COMMIT_TO_DS, &req->wb_flags);
@@ -1246,7 +1222,7 @@
 	struct nfs_open_context *ctx = nfs_file_open_context(filp);
 
 	if (nfs_ctx_key_to_expire(ctx, inode) &&
-	    !ctx->ll_cred)
+	    !rcu_access_pointer(ctx->ll_cred))
 		/* Already expired! */
 		return -EACCES;
 	return 0;
@@ -1258,23 +1234,38 @@
 bool nfs_ctx_key_to_expire(struct nfs_open_context *ctx, struct inode *inode)
 {
 	struct rpc_auth *auth = NFS_SERVER(inode)->client->cl_auth;
-	struct rpc_cred *cred = ctx->ll_cred;
+	struct rpc_cred *cred, *new, *old = NULL;
 	struct auth_cred acred = {
 		.cred = ctx->cred,
 	};
+	bool ret = false;
+
+	rcu_read_lock();
+	cred = rcu_dereference(ctx->ll_cred);
+	if (cred && !(cred->cr_ops->crkey_timeout &&
+		      cred->cr_ops->crkey_timeout(cred)))
+		goto out;
+	rcu_read_unlock();
 
-	if (cred && !cred->cr_ops->crmatch(&acred, cred, 0)) {
-		put_rpccred(cred);
-		ctx->ll_cred = NULL;
-		cred = NULL;
-	}
-	if (!cred)
-		cred = auth->au_ops->lookup_cred(auth, &acred, 0);
-	if (!cred || IS_ERR(cred))
+	new = auth->au_ops->lookup_cred(auth, &acred, 0);
+	if (new == cred) {
+		put_rpccred(new);
 		return true;
-	ctx->ll_cred = cred;
-	return !!(cred->cr_ops->crkey_timeout &&
-		  cred->cr_ops->crkey_timeout(cred));
+	}
+	if (IS_ERR_OR_NULL(new)) {
+		new = NULL;
+		ret = true;
+	} else if (new->cr_ops->crkey_timeout &&
+		   new->cr_ops->crkey_timeout(new))
+		ret = true;
+
+	rcu_read_lock();
+	old = rcu_dereference_protected(xchg(&ctx->ll_cred,
+					     RCU_INITIALIZER(new)), 1);
+out:
+	rcu_read_unlock();
+	put_rpccred(old);
+	return ret;
 }
 
 /*
@@ -1419,10 +1410,12 @@
  */
 static void nfs_redirty_request(struct nfs_page *req)
 {
+	struct nfs_inode *nfsi = NFS_I(page_file_mapping(req->wb_page)->host);
+
 	/* Bump the transmission count */
 	req->wb_nio++;
 	nfs_mark_request_dirty(req);
-	set_bit(NFS_CONTEXT_RESEND_WRITES, &nfs_req_openctx(req)->flags);
+	atomic_long_inc(&nfsi->redirtied_pages);
 	nfs_end_page_writeback(req);
 	nfs_release_request(req);
 }
@@ -1434,7 +1427,7 @@
 	while (!list_empty(head)) {
 		req = nfs_list_entry(head->next);
 		nfs_list_remove_request(req);
-		if (nfs_error_is_fatal(error))
+		if (nfs_error_is_fatal_on_server(error))
 			nfs_write_error(req, error);
 		else
 			nfs_redirty_request(req);
@@ -1444,8 +1437,6 @@
 static void nfs_async_write_reschedule_io(struct nfs_pgio_header *hdr)
 {
 	nfs_async_write_error(&hdr->pages, 0);
-	filemap_fdatawrite_range(hdr->inode->i_mapping, hdr->args.offset,
-			hdr->args.offset + hdr->args.count - 1);
 }
 
 static const struct nfs_pgio_completion_ops nfs_async_write_completion_ops = {
@@ -1666,15 +1657,18 @@
 				       !atomic_read(&cinfo->rpcs_out));
 }
 
-static void nfs_commit_begin(struct nfs_mds_commit_info *cinfo)
+void nfs_commit_begin(struct nfs_mds_commit_info *cinfo)
 {
 	atomic_inc(&cinfo->rpcs_out);
 }
 
-static void nfs_commit_end(struct nfs_mds_commit_info *cinfo)
+bool nfs_commit_end(struct nfs_mds_commit_info *cinfo)
 {
-	if (atomic_dec_and_test(&cinfo->rpcs_out))
+	if (atomic_dec_and_test(&cinfo->rpcs_out)) {
 		wake_up_var(&cinfo->rpcs_out);
+		return true;
+	}
+	return false;
 }
 
 void nfs_commitdata_release(struct nfs_commit_data *data)
@@ -1706,6 +1700,10 @@
 		.flags = RPC_TASK_ASYNC | flags,
 		.priority = priority,
 	};
+
+	if (nfs_server_capable(data->inode, NFS_CAP_MOVEABLE))
+		task_setup_data.flags |= RPC_TASK_MOVEABLE;
+
 	/* Set up the initial task struct.  */
 	nfs_ops->commit_setup(data, &msg, &task_setup_data.rpc_client);
 	trace_nfs_initiate_commit(data);
@@ -1774,6 +1772,7 @@
 	data->res.fattr   = &data->fattr;
 	data->res.verf    = &data->verf;
 	nfs_fattr_init(&data->fattr);
+	nfs_commit_begin(cinfo->mds);
 }
 EXPORT_SYMBOL_GPL(nfs_init_commit);
 
@@ -1816,11 +1815,14 @@
 	if (list_empty(head))
 		return 0;
 
-	data = nfs_commitdata_alloc(true);
+	data = nfs_commitdata_alloc();
+	if (!data) {
+		nfs_retry_commit(head, NULL, cinfo, -1);
+		return -ENOMEM;
+	}
 
 	/* Set up the argument struct */
 	nfs_init_commit(data, head, NULL, cinfo);
-	atomic_inc(&cinfo->mds->rpcs_out);
 	if (NFS_SERVER(inode)->nfs_client->cl_minorversion)
 		task_flags = RPC_TASK_MOVEABLE;
 	return nfs_initiate_commit(NFS_CLIENT(inode), data, NFS_PROTO(inode),
@@ -1884,7 +1886,7 @@
 		/* We have a mismatch. Write the page again */
 		dprintk_cont(" mismatch\n");
 		nfs_mark_request_dirty(req);
-		set_bit(NFS_CONTEXT_RESEND_WRITES, &nfs_req_openctx(req)->flags);
+		atomic_long_inc(&NFS_I(data->inode)->redirtied_pages);
 	next:
 		nfs_unlock_and_release_request(req);
 		/* Latency breaker */
@@ -1936,6 +1938,7 @@
 	int may_wait = how & FLUSH_SYNC;
 	int ret, nscan;
 
+	how &= ~FLUSH_SYNC;
 	nfs_init_cinfo_from_inode(&cinfo, inode);
 	nfs_commit_begin(cinfo.mds);
 	for (;;) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/Kconfig
@@ -8,6 +8,7 @@
 	select SUNRPC
 	select EXPORTFS
 	select NFS_ACL_SUPPORT if NFSD_V2_ACL
+	select NFS_ACL_SUPPORT if NFSD_V3_ACL
 	depends on MULTIUSER
 	help
 	  Choose Y here if you want to allow other computers to access
@@ -26,28 +27,29 @@
 
 	  Below you can choose which versions of the NFS protocol are
 	  available to clients mounting the NFS server on this system.
-	  Support for NFS version 2 (RFC 1094) is always available when
+	  Support for NFS version 3 (RFC 1813) is always available when
 	  CONFIG_NFSD is selected.
 
 	  If unsure, say N.
 
-config NFSD_V2_ACL
-	bool
-	depends on NFSD
-
-config NFSD_V3
-	bool "NFS server support for NFS version 3"
+config NFSD_V2
+	bool "NFS server support for NFS version 2 (DEPRECATED)"
 	depends on NFSD
+	default n
 	help
-	  This option enables support in your system's NFS server for
-	  version 3 of the NFS protocol (RFC 1813).
+	  NFSv2 (RFC 1094) was the first publicly-released version of NFS.
+	  Unless you are hosting ancient (1990's era) NFS clients, you don't
+	  need this.
 
-	  If unsure, say Y.
+	  If unsure, say N.
+
+config NFSD_V2_ACL
+	bool "NFS server support for the NFSv2 ACL protocol extension"
+	depends on NFSD_V2
 
 config NFSD_V3_ACL
 	bool "NFS server support for the NFSv3 ACL protocol extension"
-	depends on NFSD_V3
-	select NFSD_V2_ACL
+	depends on NFSD
 	help
 	  Solaris NFS servers support an auxiliary NFSv3 ACL protocol that
 	  never became an official part of the NFS version 3 protocol.
@@ -70,7 +72,6 @@
 config NFSD_V4
 	bool "NFS server support for NFS version 4"
 	depends on NFSD && PROC_FS
-	select NFSD_V3
 	select FS_POSIX_ACL
 	select SUNRPC_GSS
 	select CRYPTO
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/Makefile
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/Makefile
@@ -10,11 +10,11 @@
 # this one should be compiled first, as the tracing macros can easily blow up
 nfsd-y			+= trace.o
 
-nfsd-y 			+= nfssvc.o nfsctl.o nfsproc.o nfsfh.o vfs.o \
-			   export.o auth.o lockd.o nfscache.o nfsxdr.o \
-			   stats.o filecache.o
+nfsd-y 			+= nfssvc.o nfsctl.o nfsfh.o vfs.o \
+			   export.o auth.o lockd.o nfscache.o \
+			   stats.o filecache.o nfs3proc.o nfs3xdr.o
+nfsd-$(CONFIG_NFSD_V2) += nfsproc.o nfsxdr.o
 nfsd-$(CONFIG_NFSD_V2_ACL) += nfs2acl.o
-nfsd-$(CONFIG_NFSD_V3)	+= nfs3proc.o nfs3xdr.o
 nfsd-$(CONFIG_NFSD_V3_ACL) += nfs3acl.o
 nfsd-$(CONFIG_NFSD_V4)	+= nfs4proc.o nfs4xdr.o nfs4state.o nfs4idmap.o \
 			   nfs4acl.o nfs4callback.o nfs4recover.o
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/acl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/acl.h
@@ -38,6 +38,8 @@
 struct nfs4_acl;
 struct svc_fh;
 struct svc_rqst;
+struct nfsd_attrs;
+enum nfs_ftype4;
 
 int nfs4_acl_bytes(int entries);
 int nfs4_acl_get_whotype(char *, u32);
@@ -45,7 +47,7 @@
 
 int nfsd4_get_nfs4_acl(struct svc_rqst *rqstp, struct dentry *dentry,
 		struct nfs4_acl **acl);
-__be32 nfsd4_set_nfs4_acl(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		struct nfs4_acl *acl);
+__be32 nfsd4_acl_to_attr(enum nfs_ftype4 type, struct nfs4_acl *acl,
+			 struct nfsd_attrs *attr);
 
 #endif /* LINUX_NFS4_ACL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/blocklayout.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/blocklayout.c
@@ -16,6 +16,7 @@
 #include "blocklayoutxdr.h"
 #include "pnfs.h"
 #include "filecache.h"
+#include "vfs.h"
 
 #define NFSDDBG_FACILITY	NFSDDBG_PNFS
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/blocklayoutxdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/blocklayoutxdr.c
@@ -9,6 +9,7 @@
 
 #include "nfsd.h"
 #include "blocklayoutxdr.h"
+#include "vfs.h"
 
 #define NFSDDBG_FACILITY	NFSDDBG_PNFS
 
@@ -82,6 +83,15 @@
 	int len = sizeof(__be32), ret, i;
 	__be32 *p;
 
+	/*
+	 * See paragraph 5 of RFC 8881 S18.40.3.
+	 */
+	if (!gdp->gd_maxcount) {
+		if (xdr_stream_encode_u32(xdr, 0) != XDR_UNIT)
+			return nfserr_resource;
+		return nfs_ok;
+	}
+
 	p = xdr_reserve_space(xdr, len + sizeof(__be32));
 	if (!p)
 		return nfserr_resource;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/cache.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/cache.h
@@ -84,6 +84,6 @@
 void	nfsd_reply_cache_shutdown(struct nfsd_net *);
 int	nfsd_cache_lookup(struct svc_rqst *);
 void	nfsd_cache_update(struct svc_rqst *, int, __be32 *);
-int	nfsd_reply_cache_stats_open(struct inode *, struct file *);
+int	nfsd_reply_cache_stats_show(struct seq_file *m, void *v);
 
 #endif /* NFSCACHE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/export.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/export.c
@@ -339,12 +339,16 @@
 
 static void export_stats_reset(struct export_stats *stats)
 {
-	nfsd_percpu_counters_reset(stats->counter, EXP_STATS_COUNTERS_NUM);
+	if (stats)
+		nfsd_percpu_counters_reset(stats->counter,
+					   EXP_STATS_COUNTERS_NUM);
 }
 
 static void export_stats_destroy(struct export_stats *stats)
 {
-	nfsd_percpu_counters_destroy(stats->counter, EXP_STATS_COUNTERS_NUM);
+	if (stats)
+		nfsd_percpu_counters_destroy(stats->counter,
+					     EXP_STATS_COUNTERS_NUM);
 }
 
 static void svc_export_put(struct kref *ref)
@@ -353,7 +357,8 @@
 	path_put(&exp->ex_path);
 	auth_domain_put(exp->ex_client);
 	nfsd4_fslocs_free(&exp->ex_fslocs);
-	export_stats_destroy(&exp->ex_stats);
+	export_stats_destroy(exp->ex_stats);
+	kfree(exp->ex_stats);
 	kfree(exp->ex_uuid);
 	kfree_rcu(exp, ex_rcu);
 }
@@ -427,7 +432,7 @@
 		return -EINVAL;
 	}
 
-	if (mnt_user_ns(path->mnt) != &init_user_ns) {
+	if (is_idmapped_mnt(path->mnt)) {
 		dprintk("exp_export: export of idmapped mounts not yet supported.\n");
 		return -EINVAL;
 	}
@@ -744,13 +749,15 @@
 	seq_putc(m, '\t');
 	seq_escape(m, exp->ex_client->name, " \t\n\\");
 	if (export_stats) {
-		seq_printf(m, "\t%lld\n", exp->ex_stats.start_time);
+		struct percpu_counter *counter = exp->ex_stats->counter;
+
+		seq_printf(m, "\t%lld\n", exp->ex_stats->start_time);
 		seq_printf(m, "\tfh_stale: %lld\n",
-			   percpu_counter_sum_positive(&exp->ex_stats.counter[EXP_STATS_FH_STALE]));
+			   percpu_counter_sum_positive(&counter[EXP_STATS_FH_STALE]));
 		seq_printf(m, "\tio_read: %lld\n",
-			   percpu_counter_sum_positive(&exp->ex_stats.counter[EXP_STATS_IO_READ]));
+			   percpu_counter_sum_positive(&counter[EXP_STATS_IO_READ]));
 		seq_printf(m, "\tio_write: %lld\n",
-			   percpu_counter_sum_positive(&exp->ex_stats.counter[EXP_STATS_IO_WRITE]));
+			   percpu_counter_sum_positive(&counter[EXP_STATS_IO_WRITE]));
 		seq_putc(m, '\n');
 		return 0;
 	}
@@ -796,7 +803,7 @@
 	new->ex_layout_types = 0;
 	new->ex_uuid = NULL;
 	new->cd = item->cd;
-	export_stats_reset(&new->ex_stats);
+	export_stats_reset(new->ex_stats);
 }
 
 static void export_update(struct cache_head *cnew, struct cache_head *citem)
@@ -832,7 +839,14 @@
 	if (!i)
 		return NULL;
 
-	if (export_stats_init(&i->ex_stats)) {
+	i->ex_stats = kmalloc(sizeof(*(i->ex_stats)), GFP_KERNEL);
+	if (!i->ex_stats) {
+		kfree(i);
+		return NULL;
+	}
+
+	if (export_stats_init(i->ex_stats)) {
+		kfree(i->ex_stats);
 		kfree(i);
 		return NULL;
 	}
@@ -1310,9 +1324,12 @@
 		return 0;
 	}
 
-	exp_get(exp);
+	if (!cache_get_rcu(&exp->h))
+		return 0;
+
 	if (cache_check(cd, &exp->h, NULL))
 		return 0;
+
 	exp_put(exp);
 	return svc_export_show(m, cd, cp);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/export.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/export.h
@@ -64,10 +64,10 @@
 	struct cache_head	h;
 	struct auth_domain *	ex_client;
 	int			ex_flags;
+	int			ex_fsid;
 	struct path		ex_path;
 	kuid_t			ex_anon_uid;
 	kgid_t			ex_anon_gid;
-	int			ex_fsid;
 	unsigned char *		ex_uuid; /* 16 byte fsid */
 	struct nfsd4_fs_locations ex_fslocs;
 	uint32_t		ex_nflavors;
@@ -76,7 +76,7 @@
 	struct nfsd4_deviceid_map *ex_devid_map;
 	struct cache_detail	*cd;
 	struct rcu_head		ex_rcu;
-	struct export_stats	ex_stats;
+	struct export_stats	*ex_stats;
 };
 
 /* an "export key" (expkey) maps a filehandlefragement to an
@@ -115,7 +115,6 @@
 int			exp_rootfh(struct net *, struct auth_domain *,
 					char *path, struct knfsd_fh *, int maxsize);
 __be32			exp_pseudoroot(struct svc_rqst *, struct svc_fh *);
-__be32			nfserrno(int errno);
 
 static inline void exp_put(struct svc_export *exp)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/filecache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/filecache.c
@@ -1,7 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
- * Open file cache.
+ * The NFSD open file cache.
  *
  * (c) 2015 - Jeff Layton <jeff.layton@primarydata.com>
+ *
+ * An nfsd_file object is a per-file collection of open state that binds
+ * together:
+ *   - a struct file *
+ *   - a user credential
+ *   - a network namespace
+ *   - a read-ahead context
+ *   - monitoring for writeback errors
+ *
+ * nfsd_file objects are reference-counted. Consumers acquire a new
+ * object via the nfsd_file_acquire API. They manage their interest in
+ * the acquired object, and hence the object's reference count, via
+ * nfsd_file_get and nfsd_file_put. There are two varieties of nfsd_file
+ * object:
+ *
+ *  * non-garbage-collected: When a consumer wants to precisely control
+ *    the lifetime of a file's open state, it acquires a non-garbage-
+ *    collected nfsd_file. The final nfsd_file_put releases the open
+ *    state immediately.
+ *
+ *  * garbage-collected: When a consumer does not control the lifetime
+ *    of open state, it acquires a garbage-collected nfsd_file. The
+ *    final nfsd_file_put allows the open state to linger for a period
+ *    during which it may be re-used.
  */
 
 #include <linux/hash.h>
@@ -12,6 +37,7 @@
 #include <linux/fsnotify_backend.h>
 #include <linux/fsnotify.h>
 #include <linux/seq_file.h>
+#include <linux/rhashtable.h>
 
 #include "vfs.h"
 #include "nfsd.h"
@@ -20,63 +46,75 @@
 #include "filecache.h"
 #include "trace.h"
 
-#define NFSDDBG_FACILITY	NFSDDBG_FH
-
-/* FIXME: dynamically size this for the machine somehow? */
-#define NFSD_FILE_HASH_BITS                   12
-#define NFSD_FILE_HASH_SIZE                  (1 << NFSD_FILE_HASH_BITS)
 #define NFSD_LAUNDRETTE_DELAY		     (2 * HZ)
 
-#define NFSD_FILE_SHUTDOWN		     (1)
-#define NFSD_FILE_LRU_THRESHOLD		     (4096UL)
-#define NFSD_FILE_LRU_LIMIT		     (NFSD_FILE_LRU_THRESHOLD << 2)
+#define NFSD_FILE_CACHE_UP		     (0)
 
 /* We only care about NFSD_MAY_READ/WRITE for this cache */
 #define NFSD_FILE_MAY_MASK	(NFSD_MAY_READ|NFSD_MAY_WRITE)
 
-struct nfsd_fcache_bucket {
-	struct hlist_head	nfb_head;
-	spinlock_t		nfb_lock;
-	unsigned int		nfb_count;
-	unsigned int		nfb_maxcount;
-};
-
 static DEFINE_PER_CPU(unsigned long, nfsd_file_cache_hits);
+static DEFINE_PER_CPU(unsigned long, nfsd_file_acquisitions);
+static DEFINE_PER_CPU(unsigned long, nfsd_file_releases);
+static DEFINE_PER_CPU(unsigned long, nfsd_file_total_age);
+static DEFINE_PER_CPU(unsigned long, nfsd_file_evictions);
 
 struct nfsd_fcache_disposal {
-	struct list_head list;
 	struct work_struct work;
-	struct net *net;
 	spinlock_t lock;
 	struct list_head freeme;
-	struct rcu_head rcu;
 };
 
 static struct workqueue_struct *nfsd_filecache_wq __read_mostly;
 
 static struct kmem_cache		*nfsd_file_slab;
 static struct kmem_cache		*nfsd_file_mark_slab;
-static struct nfsd_fcache_bucket	*nfsd_file_hashtbl;
 static struct list_lru			nfsd_file_lru;
-static long				nfsd_file_lru_flags;
+static unsigned long			nfsd_file_flags;
 static struct fsnotify_group		*nfsd_file_fsnotify_group;
-static atomic_long_t			nfsd_filecache_count;
 static struct delayed_work		nfsd_filecache_laundrette;
-static DEFINE_SPINLOCK(laundrette_lock);
-static LIST_HEAD(laundrettes);
+static struct rhltable			nfsd_file_rhltable
+						____cacheline_aligned_in_smp;
 
-static void nfsd_file_gc(void);
+static bool
+nfsd_match_cred(const struct cred *c1, const struct cred *c2)
+{
+	int i;
+
+	if (!uid_eq(c1->fsuid, c2->fsuid))
+		return false;
+	if (!gid_eq(c1->fsgid, c2->fsgid))
+		return false;
+	if (c1->group_info == NULL || c2->group_info == NULL)
+		return c1->group_info == c2->group_info;
+	if (c1->group_info->ngroups != c2->group_info->ngroups)
+		return false;
+	for (i = 0; i < c1->group_info->ngroups; i++) {
+		if (!gid_eq(c1->group_info->gid[i], c2->group_info->gid[i]))
+			return false;
+	}
+	return true;
+}
+
+static const struct rhashtable_params nfsd_file_rhash_params = {
+	.key_len		= sizeof_field(struct nfsd_file, nf_inode),
+	.key_offset		= offsetof(struct nfsd_file, nf_inode),
+	.head_offset		= offsetof(struct nfsd_file, nf_rlist),
+
+	/*
+	 * Start with a single page hash table to reduce resizing churn
+	 * on light workloads.
+	 */
+	.min_size		= 256,
+	.automatic_shrinking	= true,
+};
 
 static void
 nfsd_file_schedule_laundrette(void)
 {
-	long count = atomic_long_read(&nfsd_filecache_count);
-
-	if (count == 0 || test_bit(NFSD_FILE_SHUTDOWN, &nfsd_file_lru_flags))
-		return;
-
-	queue_delayed_work(system_wq, &nfsd_filecache_laundrette,
-			NFSD_LAUNDRETTE_DELAY);
+	if (test_bit(NFSD_FILE_CACHE_UP, &nfsd_file_flags))
+		queue_delayed_work(system_wq, &nfsd_filecache_laundrette,
+				   NFSD_LAUNDRETTE_DELAY);
 }
 
 static void
@@ -115,22 +153,21 @@
 }
 
 static struct nfsd_file_mark *
-nfsd_file_mark_find_or_create(struct nfsd_file *nf)
+nfsd_file_mark_find_or_create(struct nfsd_file *nf, struct inode *inode)
 {
 	int			err;
 	struct fsnotify_mark	*mark;
 	struct nfsd_file_mark	*nfm = NULL, *new;
-	struct inode *inode = nf->nf_inode;
 
 	do {
-		mutex_lock(&nfsd_file_fsnotify_group->mark_mutex);
+		fsnotify_group_lock(nfsd_file_fsnotify_group);
 		mark = fsnotify_find_mark(&inode->i_fsnotify_marks,
-				nfsd_file_fsnotify_group);
+					  nfsd_file_fsnotify_group);
 		if (mark) {
 			nfm = nfsd_file_mark_get(container_of(mark,
 						 struct nfsd_file_mark,
 						 nfm_mark));
-			mutex_unlock(&nfsd_file_fsnotify_group->mark_mutex);
+			fsnotify_group_unlock(nfsd_file_fsnotify_group);
 			if (nfm) {
 				fsnotify_put_mark(mark);
 				break;
@@ -138,8 +175,9 @@
 			/* Avoid soft lockup race with nfsd_file_mark_put() */
 			fsnotify_destroy_mark(mark, nfsd_file_fsnotify_group);
 			fsnotify_put_mark(mark);
-		} else
-			mutex_unlock(&nfsd_file_fsnotify_group->mark_mutex);
+		} else {
+			fsnotify_group_unlock(nfsd_file_fsnotify_group);
+		}
 
 		/* allocate a new nfm */
 		new = kmem_cache_alloc(nfsd_file_mark_slab, GFP_KERNEL);
@@ -170,52 +208,92 @@
 }
 
 static struct nfsd_file *
-nfsd_file_alloc(struct inode *inode, unsigned int may, unsigned int hashval,
-		struct net *net)
+nfsd_file_alloc(struct net *net, struct inode *inode, unsigned char need,
+		bool want_gc)
 {
 	struct nfsd_file *nf;
 
 	nf = kmem_cache_alloc(nfsd_file_slab, GFP_KERNEL);
-	if (nf) {
-		INIT_HLIST_NODE(&nf->nf_node);
-		INIT_LIST_HEAD(&nf->nf_lru);
-		nf->nf_file = NULL;
-		nf->nf_cred = get_current_cred();
-		nf->nf_net = net;
-		nf->nf_flags = 0;
-		nf->nf_inode = inode;
-		nf->nf_hashval = hashval;
-		refcount_set(&nf->nf_ref, 1);
-		nf->nf_may = may & NFSD_FILE_MAY_MASK;
-		if (may & NFSD_MAY_NOT_BREAK_LEASE) {
-			if (may & NFSD_MAY_WRITE)
-				__set_bit(NFSD_FILE_BREAK_WRITE, &nf->nf_flags);
-			if (may & NFSD_MAY_READ)
-				__set_bit(NFSD_FILE_BREAK_READ, &nf->nf_flags);
-		}
-		nf->nf_mark = NULL;
-		init_rwsem(&nf->nf_rwsem);
-		trace_nfsd_file_alloc(nf);
-	}
+	if (unlikely(!nf))
+		return NULL;
+
+	INIT_LIST_HEAD(&nf->nf_lru);
+	INIT_LIST_HEAD(&nf->nf_gc);
+	nf->nf_birthtime = ktime_get();
+	nf->nf_file = NULL;
+	nf->nf_cred = get_current_cred();
+	nf->nf_net = net;
+	nf->nf_flags = want_gc ?
+		BIT(NFSD_FILE_HASHED) | BIT(NFSD_FILE_PENDING) | BIT(NFSD_FILE_GC) :
+		BIT(NFSD_FILE_HASHED) | BIT(NFSD_FILE_PENDING);
+	nf->nf_inode = inode;
+	refcount_set(&nf->nf_ref, 1);
+	nf->nf_may = need;
+	nf->nf_mark = NULL;
 	return nf;
 }
 
+/**
+ * nfsd_file_check_write_error - check for writeback errors on a file
+ * @nf: nfsd_file to check for writeback errors
+ *
+ * Check whether a nfsd_file has an unseen error. Reset the write
+ * verifier if so.
+ */
+static void
+nfsd_file_check_write_error(struct nfsd_file *nf)
+{
+	struct file *file = nf->nf_file;
+
+	if ((file->f_mode & FMODE_WRITE) &&
+	    filemap_check_wb_err(file->f_mapping, READ_ONCE(file->f_wb_err)))
+		nfsd_reset_write_verifier(net_generic(nf->nf_net, nfsd_net_id));
+}
+
+static void
+nfsd_file_hash_remove(struct nfsd_file *nf)
+{
+	trace_nfsd_file_unhash(nf);
+	rhltable_remove(&nfsd_file_rhltable, &nf->nf_rlist,
+			nfsd_file_rhash_params);
+}
+
 static bool
+nfsd_file_unhash(struct nfsd_file *nf)
+{
+	if (test_and_clear_bit(NFSD_FILE_HASHED, &nf->nf_flags)) {
+		nfsd_file_hash_remove(nf);
+		return true;
+	}
+	return false;
+}
+
+static void
 nfsd_file_free(struct nfsd_file *nf)
 {
-	bool flush = false;
+	s64 age = ktime_to_ms(ktime_sub(ktime_get(), nf->nf_birthtime));
 
-	trace_nfsd_file_put_final(nf);
+	trace_nfsd_file_free(nf);
+
+	this_cpu_inc(nfsd_file_releases);
+	this_cpu_add(nfsd_file_total_age, age);
+
+	nfsd_file_unhash(nf);
 	if (nf->nf_mark)
 		nfsd_file_mark_put(nf->nf_mark);
 	if (nf->nf_file) {
-		get_file(nf->nf_file);
+		nfsd_file_check_write_error(nf);
 		filp_close(nf->nf_file, NULL);
-		fput(nf->nf_file);
-		flush = true;
 	}
+
+	/*
+	 * If this item is still linked via nf_lru, that's a bug.
+	 * WARN and leak it to preserve system stability.
+	 */
+	if (WARN_ON_ONCE(!list_empty(&nf->nf_lru)))
+		return;
+
 	call_rcu(&nf->nf_rcu, nfsd_file_slab_free);
-	return flush;
 }
 
 static bool
@@ -224,191 +302,140 @@
 	struct file *file = nf->nf_file;
 	struct address_space *mapping;
 
-	if (!file || !(file->f_mode & FMODE_WRITE))
+	/* File not open for write? */
+	if (!(file->f_mode & FMODE_WRITE))
 		return false;
+
+	/*
+	 * Some filesystems (e.g. NFS) flush all dirty data on close.
+	 * On others, there is no need to wait for writeback.
+	 */
+	if (!(file_inode(file)->i_sb->s_export_op->flags & EXPORT_OP_FLUSH_ON_CLOSE))
+		return false;
+
 	mapping = file->f_mapping;
 	return mapping_tagged(mapping, PAGECACHE_TAG_DIRTY) ||
 		mapping_tagged(mapping, PAGECACHE_TAG_WRITEBACK);
 }
 
-static int
-nfsd_file_check_write_error(struct nfsd_file *nf)
-{
-	struct file *file = nf->nf_file;
 
-	if (!file || !(file->f_mode & FMODE_WRITE))
-		return 0;
-	return filemap_check_wb_err(file->f_mapping, READ_ONCE(file->f_wb_err));
-}
-
-static void
-nfsd_file_do_unhash(struct nfsd_file *nf)
+static bool nfsd_file_lru_add(struct nfsd_file *nf)
 {
-	lockdep_assert_held(&nfsd_file_hashtbl[nf->nf_hashval].nfb_lock);
-
-	trace_nfsd_file_unhash(nf);
-
-	if (nfsd_file_check_write_error(nf))
-		nfsd_reset_boot_verifier(net_generic(nf->nf_net, nfsd_net_id));
-	--nfsd_file_hashtbl[nf->nf_hashval].nfb_count;
-	hlist_del_rcu(&nf->nf_node);
-	atomic_long_dec(&nfsd_filecache_count);
-}
-
-static bool
-nfsd_file_unhash(struct nfsd_file *nf)
-{
-	if (test_and_clear_bit(NFSD_FILE_HASHED, &nf->nf_flags)) {
-		nfsd_file_do_unhash(nf);
-		if (!list_empty(&nf->nf_lru))
-			list_lru_del(&nfsd_file_lru, &nf->nf_lru);
+	set_bit(NFSD_FILE_REFERENCED, &nf->nf_flags);
+	if (list_lru_add(&nfsd_file_lru, &nf->nf_lru)) {
+		trace_nfsd_file_lru_add(nf);
 		return true;
 	}
 	return false;
 }
 
-/*
- * Return true if the file was unhashed.
- */
-static bool
-nfsd_file_unhash_and_release_locked(struct nfsd_file *nf, struct list_head *dispose)
+static bool nfsd_file_lru_remove(struct nfsd_file *nf)
 {
-	lockdep_assert_held(&nfsd_file_hashtbl[nf->nf_hashval].nfb_lock);
-
-	trace_nfsd_file_unhash_and_release_locked(nf);
-	if (!nfsd_file_unhash(nf))
-		return false;
-	/* keep final reference for nfsd_file_lru_dispose */
-	if (refcount_dec_not_one(&nf->nf_ref))
+	if (list_lru_del(&nfsd_file_lru, &nf->nf_lru)) {
+		trace_nfsd_file_lru_del(nf);
 		return true;
-
-	list_add(&nf->nf_lru, dispose);
-	return true;
-}
-
-static void
-nfsd_file_put_noref(struct nfsd_file *nf)
-{
-	trace_nfsd_file_put(nf);
-
-	if (refcount_dec_and_test(&nf->nf_ref)) {
-		WARN_ON(test_bit(NFSD_FILE_HASHED, &nf->nf_flags));
-		nfsd_file_free(nf);
-	}
-}
-
-void
-nfsd_file_put(struct nfsd_file *nf)
-{
-	bool is_hashed;
-
-	set_bit(NFSD_FILE_REFERENCED, &nf->nf_flags);
-	if (refcount_read(&nf->nf_ref) > 2 || !nf->nf_file) {
-		nfsd_file_put_noref(nf);
-		return;
 	}
-
-	filemap_flush(nf->nf_file->f_mapping);
-	is_hashed = test_bit(NFSD_FILE_HASHED, &nf->nf_flags) != 0;
-	nfsd_file_put_noref(nf);
-	if (is_hashed)
-		nfsd_file_schedule_laundrette();
-	if (atomic_long_read(&nfsd_filecache_count) >= NFSD_FILE_LRU_LIMIT)
-		nfsd_file_gc();
+	return false;
 }
 
 struct nfsd_file *
 nfsd_file_get(struct nfsd_file *nf)
 {
-	if (likely(refcount_inc_not_zero(&nf->nf_ref)))
+	if (nf && refcount_inc_not_zero(&nf->nf_ref))
 		return nf;
 	return NULL;
 }
 
-static void
-nfsd_file_dispose_list(struct list_head *dispose)
-{
-	struct nfsd_file *nf;
-
-	while(!list_empty(dispose)) {
-		nf = list_first_entry(dispose, struct nfsd_file, nf_lru);
-		list_del(&nf->nf_lru);
-		nfsd_file_put_noref(nf);
-	}
-}
-
-static void
-nfsd_file_dispose_list_sync(struct list_head *dispose)
+/**
+ * nfsd_file_put - put the reference to a nfsd_file
+ * @nf: nfsd_file of which to put the reference
+ *
+ * Put a reference to a nfsd_file. In the non-GC case, we just put the
+ * reference immediately. In the GC case, if the reference would be
+ * the last one, the put it on the LRU instead to be cleaned up later.
+ */
+void
+nfsd_file_put(struct nfsd_file *nf)
 {
-	bool flush = false;
-	struct nfsd_file *nf;
-
-	while(!list_empty(dispose)) {
-		nf = list_first_entry(dispose, struct nfsd_file, nf_lru);
-		list_del(&nf->nf_lru);
-		if (!refcount_dec_and_test(&nf->nf_ref))
-			continue;
-		if (nfsd_file_free(nf))
-			flush = true;
-	}
-	if (flush)
-		flush_delayed_fput();
-}
+	might_sleep();
+	trace_nfsd_file_put(nf);
 
-static void
-nfsd_file_list_remove_disposal(struct list_head *dst,
-		struct nfsd_fcache_disposal *l)
-{
-	spin_lock(&l->lock);
-	list_splice_init(&l->freeme, dst);
-	spin_unlock(&l->lock);
-}
+	if (test_bit(NFSD_FILE_GC, &nf->nf_flags) &&
+	    test_bit(NFSD_FILE_HASHED, &nf->nf_flags)) {
+		/*
+		 * If this is the last reference (nf_ref == 1), then try to
+		 * transfer it to the LRU.
+		 */
+		if (refcount_dec_not_one(&nf->nf_ref))
+			return;
 
-static void
-nfsd_file_list_add_disposal(struct list_head *files, struct net *net)
-{
-	struct nfsd_fcache_disposal *l;
+		/* Try to add it to the LRU.  If that fails, decrement. */
+		if (nfsd_file_lru_add(nf)) {
+			/* If it's still hashed, we're done */
+			if (test_bit(NFSD_FILE_HASHED, &nf->nf_flags)) {
+				nfsd_file_schedule_laundrette();
+				return;
+			}
 
-	rcu_read_lock();
-	list_for_each_entry_rcu(l, &laundrettes, list) {
-		if (l->net == net) {
-			spin_lock(&l->lock);
-			list_splice_tail_init(files, &l->freeme);
-			spin_unlock(&l->lock);
-			queue_work(nfsd_filecache_wq, &l->work);
-			break;
+			/*
+			 * We're racing with unhashing, so try to remove it from
+			 * the LRU. If removal fails, then someone else already
+			 * has our reference.
+			 */
+			if (!nfsd_file_lru_remove(nf))
+				return;
 		}
 	}
-	rcu_read_unlock();
+	if (refcount_dec_and_test(&nf->nf_ref))
+		nfsd_file_free(nf);
 }
 
 static void
-nfsd_file_list_add_pernet(struct list_head *dst, struct list_head *src,
-		struct net *net)
+nfsd_file_dispose_list(struct list_head *dispose)
 {
-	struct nfsd_file *nf, *tmp;
+	struct nfsd_file *nf;
 
-	list_for_each_entry_safe(nf, tmp, src, nf_lru) {
-		if (nf->nf_net == net)
-			list_move_tail(&nf->nf_lru, dst);
+	while (!list_empty(dispose)) {
+		nf = list_first_entry(dispose, struct nfsd_file, nf_gc);
+		list_del_init(&nf->nf_gc);
+		nfsd_file_free(nf);
 	}
 }
 
+/**
+ * nfsd_file_dispose_list_delayed - move list of dead files to net's freeme list
+ * @dispose: list of nfsd_files to be disposed
+ *
+ * Transfers each file to the "freeme" list for its nfsd_net, to eventually
+ * be disposed of by the per-net garbage collector.
+ */
 static void
 nfsd_file_dispose_list_delayed(struct list_head *dispose)
 {
-	LIST_HEAD(list);
-	struct nfsd_file *nf;
-
 	while(!list_empty(dispose)) {
-		nf = list_first_entry(dispose, struct nfsd_file, nf_lru);
-		nfsd_file_list_add_pernet(&list, dispose, nf->nf_net);
-		nfsd_file_list_add_disposal(&list, nf->nf_net);
+		struct nfsd_file *nf = list_first_entry(dispose,
+						struct nfsd_file, nf_gc);
+		struct nfsd_net *nn = net_generic(nf->nf_net, nfsd_net_id);
+		struct nfsd_fcache_disposal *l = nn->fcache_disposal;
+
+		spin_lock(&l->lock);
+		list_move_tail(&nf->nf_gc, &l->freeme);
+		spin_unlock(&l->lock);
+		queue_work(nfsd_filecache_wq, &l->work);
 	}
 }
 
-/*
- * Note this can deadlock with nfsd_file_cache_purge.
+/**
+ * nfsd_file_lru_cb - Examine an entry on the LRU list
+ * @item: LRU entry to examine
+ * @lru: controlling LRU
+ * @lock: LRU list lock (unused)
+ * @arg: dispose list
+ *
+ * Return values:
+ *   %LRU_REMOVED: @item was removed from the LRU
+ *   %LRU_ROTATE: @item is to be moved to the LRU tail
+ *   %LRU_SKIP: @item cannot be evicted
  */
 static enum lru_status
 nfsd_file_lru_cb(struct list_head *item, struct list_lru_one *lru,
@@ -419,72 +446,61 @@
 	struct list_head *head = arg;
 	struct nfsd_file *nf = list_entry(item, struct nfsd_file, nf_lru);
 
-	/*
-	 * Do a lockless refcount check. The hashtable holds one reference, so
-	 * we look to see if anything else has a reference, or if any have
-	 * been put since the shrinker last ran. Those don't get unhashed and
-	 * released.
-	 *
-	 * Note that in the put path, we set the flag and then decrement the
-	 * counter. Here we check the counter and then test and clear the flag.
-	 * That order is deliberate to ensure that we can do this locklessly.
-	 */
-	if (refcount_read(&nf->nf_ref) > 1)
-		goto out_skip;
+	/* We should only be dealing with GC entries here */
+	WARN_ON_ONCE(!test_bit(NFSD_FILE_GC, &nf->nf_flags));
 
 	/*
 	 * Don't throw out files that are still undergoing I/O or
 	 * that have uncleared errors pending.
 	 */
-	if (nfsd_file_check_writeback(nf))
-		goto out_skip;
+	if (nfsd_file_check_writeback(nf)) {
+		trace_nfsd_file_gc_writeback(nf);
+		return LRU_SKIP;
+	}
 
-	if (test_and_clear_bit(NFSD_FILE_REFERENCED, &nf->nf_flags))
-		goto out_skip;
+	/* If it was recently added to the list, skip it */
+	if (test_and_clear_bit(NFSD_FILE_REFERENCED, &nf->nf_flags)) {
+		trace_nfsd_file_gc_referenced(nf);
+		return LRU_ROTATE;
+	}
 
-	if (!test_and_clear_bit(NFSD_FILE_HASHED, &nf->nf_flags))
-		goto out_skip;
+	/*
+	 * Put the reference held on behalf of the LRU. If it wasn't the last
+	 * one, then just remove it from the LRU and ignore it.
+	 */
+	if (!refcount_dec_and_test(&nf->nf_ref)) {
+		trace_nfsd_file_gc_in_use(nf);
+		list_lru_isolate(lru, &nf->nf_lru);
+		return LRU_REMOVED;
+	}
 
-	list_lru_isolate_move(lru, &nf->nf_lru, head);
+	/* Refcount went to zero. Unhash it and queue it to the dispose list */
+	nfsd_file_unhash(nf);
+	list_lru_isolate(lru, &nf->nf_lru);
+	list_add(&nf->nf_gc, head);
+	this_cpu_inc(nfsd_file_evictions);
+	trace_nfsd_file_gc_disposed(nf);
 	return LRU_REMOVED;
-out_skip:
-	return LRU_SKIP;
-}
-
-static unsigned long
-nfsd_file_lru_walk_list(struct shrink_control *sc)
-{
-	LIST_HEAD(head);
-	struct nfsd_file *nf;
-	unsigned long ret;
-
-	if (sc)
-		ret = list_lru_shrink_walk(&nfsd_file_lru, sc,
-				nfsd_file_lru_cb, &head);
-	else
-		ret = list_lru_walk(&nfsd_file_lru,
-				nfsd_file_lru_cb,
-				&head, LONG_MAX);
-	list_for_each_entry(nf, &head, nf_lru) {
-		spin_lock(&nfsd_file_hashtbl[nf->nf_hashval].nfb_lock);
-		nfsd_file_do_unhash(nf);
-		spin_unlock(&nfsd_file_hashtbl[nf->nf_hashval].nfb_lock);
-	}
-	nfsd_file_dispose_list_delayed(&head);
-	return ret;
 }
 
 static void
 nfsd_file_gc(void)
 {
-	nfsd_file_lru_walk_list(NULL);
+	LIST_HEAD(dispose);
+	unsigned long ret;
+
+	ret = list_lru_walk(&nfsd_file_lru, nfsd_file_lru_cb,
+			    &dispose, list_lru_count(&nfsd_file_lru));
+	trace_nfsd_file_gc_removed(ret, list_lru_count(&nfsd_file_lru));
+	nfsd_file_dispose_list_delayed(&dispose);
 }
 
 static void
 nfsd_file_gc_worker(struct work_struct *work)
 {
 	nfsd_file_gc();
-	nfsd_file_schedule_laundrette();
+	if (list_lru_count(&nfsd_file_lru))
+		nfsd_file_schedule_laundrette();
 }
 
 static unsigned long
@@ -496,7 +512,14 @@
 static unsigned long
 nfsd_file_lru_scan(struct shrinker *s, struct shrink_control *sc)
 {
-	return nfsd_file_lru_walk_list(sc);
+	LIST_HEAD(dispose);
+	unsigned long ret;
+
+	ret = list_lru_shrink_walk(&nfsd_file_lru, sc,
+				   nfsd_file_lru_cb, &dispose);
+	trace_nfsd_file_shrinker_removed(ret, list_lru_count(&nfsd_file_lru));
+	nfsd_file_dispose_list_delayed(&dispose);
+	return ret;
 }
 
 static struct shrinker	nfsd_file_shrinker = {
@@ -505,70 +528,123 @@
 	.seeks = 1,
 };
 
+/**
+ * nfsd_file_cond_queue - conditionally unhash and queue a nfsd_file
+ * @nf: nfsd_file to attempt to queue
+ * @dispose: private list to queue successfully-put objects
+ *
+ * Unhash an nfsd_file, try to get a reference to it, and then put that
+ * reference. If it's the last reference, queue it to the dispose list.
+ */
 static void
-__nfsd_file_close_inode(struct inode *inode, unsigned int hashval,
-			struct list_head *dispose)
+nfsd_file_cond_queue(struct nfsd_file *nf, struct list_head *dispose)
+	__must_hold(RCU)
 {
-	struct nfsd_file	*nf;
-	struct hlist_node	*tmp;
+	int decrement = 1;
+
+	/* If we raced with someone else unhashing, ignore it */
+	if (!nfsd_file_unhash(nf))
+		return;
+
+	/* If we can't get a reference, ignore it */
+	if (!nfsd_file_get(nf))
+		return;
 
-	spin_lock(&nfsd_file_hashtbl[hashval].nfb_lock);
-	hlist_for_each_entry_safe(nf, tmp, &nfsd_file_hashtbl[hashval].nfb_head, nf_node) {
-		if (inode == nf->nf_inode)
-			nfsd_file_unhash_and_release_locked(nf, dispose);
+	/* Extra decrement if we remove from the LRU */
+	if (nfsd_file_lru_remove(nf))
+		++decrement;
+
+	/* If refcount goes to 0, then put on the dispose list */
+	if (refcount_sub_and_test(decrement, &nf->nf_ref)) {
+		list_add(&nf->nf_gc, dispose);
+		trace_nfsd_file_closing(nf);
 	}
-	spin_unlock(&nfsd_file_hashtbl[hashval].nfb_lock);
 }
 
 /**
- * nfsd_file_close_inode_sync - attempt to forcibly close a nfsd_file
- * @inode: inode of the file to attempt to remove
+ * nfsd_file_queue_for_close: try to close out any open nfsd_files for an inode
+ * @inode:   inode on which to close out nfsd_files
+ * @dispose: list on which to gather nfsd_files to close out
+ *
+ * An nfsd_file represents a struct file being held open on behalf of nfsd.
+ * An open file however can block other activity (such as leases), or cause
+ * undesirable behavior (e.g. spurious silly-renames when reexporting NFS).
  *
- * Walk the whole hash bucket, looking for any files that correspond to "inode".
- * If any do, then unhash them and put the hashtable reference to them and
- * destroy any that had their last reference put. Also ensure that any of the
- * fputs also have their final __fput done as well.
+ * This function is intended to find open nfsd_files when this sort of
+ * conflicting access occurs and then attempt to close those files out.
+ *
+ * Populates the dispose list with entries that have already had their
+ * refcounts go to zero. The actual free of an nfsd_file can be expensive,
+ * so we leave it up to the caller whether it wants to wait or not.
  */
-void
-nfsd_file_close_inode_sync(struct inode *inode)
+static void
+nfsd_file_queue_for_close(struct inode *inode, struct list_head *dispose)
 {
-	unsigned int		hashval = (unsigned int)hash_long(inode->i_ino,
-						NFSD_FILE_HASH_BITS);
-	LIST_HEAD(dispose);
+	struct rhlist_head *tmp, *list;
+	struct nfsd_file *nf;
 
-	__nfsd_file_close_inode(inode, hashval, &dispose);
-	trace_nfsd_file_close_inode_sync(inode, hashval, !list_empty(&dispose));
-	nfsd_file_dispose_list_sync(&dispose);
+	rcu_read_lock();
+	list = rhltable_lookup(&nfsd_file_rhltable, &inode,
+			       nfsd_file_rhash_params);
+	rhl_for_each_entry_rcu(nf, tmp, list, nf_rlist) {
+		if (!test_bit(NFSD_FILE_GC, &nf->nf_flags))
+			continue;
+		nfsd_file_cond_queue(nf, dispose);
+	}
+	rcu_read_unlock();
 }
 
 /**
  * nfsd_file_close_inode - attempt a delayed close of a nfsd_file
  * @inode: inode of the file to attempt to remove
  *
- * Walk the whole hash bucket, looking for any files that correspond to "inode".
- * If any do, then unhash them and put the hashtable reference to them and
- * destroy any that had their last reference put.
+ * Close out any open nfsd_files that can be reaped for @inode. The
+ * actual freeing is deferred to the dispose_list_delayed infrastructure.
+ *
+ * This is used by the fsnotify callbacks and setlease notifier.
  */
 static void
 nfsd_file_close_inode(struct inode *inode)
 {
-	unsigned int		hashval = (unsigned int)hash_long(inode->i_ino,
-						NFSD_FILE_HASH_BITS);
 	LIST_HEAD(dispose);
 
-	__nfsd_file_close_inode(inode, hashval, &dispose);
-	trace_nfsd_file_close_inode(inode, hashval, !list_empty(&dispose));
+	nfsd_file_queue_for_close(inode, &dispose);
 	nfsd_file_dispose_list_delayed(&dispose);
 }
 
 /**
+ * nfsd_file_close_inode_sync - attempt to forcibly close a nfsd_file
+ * @inode: inode of the file to attempt to remove
+ *
+ * Close out any open nfsd_files that can be reaped for @inode. The
+ * nfsd_files are closed out synchronously.
+ *
+ * This is called from nfsd_rename and nfsd_unlink to avoid silly-renames
+ * when reexporting NFS.
+ */
+void
+nfsd_file_close_inode_sync(struct inode *inode)
+{
+	struct nfsd_file *nf;
+	LIST_HEAD(dispose);
+
+	trace_nfsd_file_close(inode);
+
+	nfsd_file_queue_for_close(inode, &dispose);
+	while (!list_empty(&dispose)) {
+		nf = list_first_entry(&dispose, struct nfsd_file, nf_gc);
+		list_del_init(&nf->nf_gc);
+		nfsd_file_free(nf);
+	}
+	flush_delayed_fput();
+}
+
+/**
  * nfsd_file_delayed_close - close unused nfsd_files
  * @work: dummy
  *
- * Walk the LRU list and close any entries that have not been used since
- * the last scan.
- *
- * Note this can deadlock with nfsd_file_cache_purge.
+ * Scrape the freeme list for this nfsd_net, and then dispose of them
+ * all.
  */
 static void
 nfsd_file_delayed_close(struct work_struct *work)
@@ -577,7 +653,10 @@
 	struct nfsd_fcache_disposal *l = container_of(work,
 			struct nfsd_fcache_disposal, work);
 
-	nfsd_file_list_remove_disposal(&head, l);
+	spin_lock(&l->lock);
+	list_splice_init(&l->freeme, &head);
+	spin_unlock(&l->lock);
+
 	nfsd_file_dispose_list(&head);
 }
 
@@ -589,7 +668,7 @@
 
 	/* Only close files for F_SETLEASE leases */
 	if (fl->fl_flags & FL_LEASE)
-		nfsd_file_close_inode_sync(file_inode(fl->fl_file));
+		nfsd_file_close_inode(file_inode(fl->fl_file));
 	return 0;
 }
 
@@ -602,6 +681,9 @@
 				struct inode *inode, struct inode *dir,
 				const struct qstr *name, u32 cookie)
 {
+	if (WARN_ON_ONCE(!inode))
+		return 0;
+
 	trace_nfsd_file_fsnotify_handle_event(inode, mask);
 
 	/* Should be no marks on non-regular files */
@@ -629,25 +711,21 @@
 int
 nfsd_file_cache_init(void)
 {
-	int		ret = -ENOMEM;
-	unsigned int	i;
-
-	clear_bit(NFSD_FILE_SHUTDOWN, &nfsd_file_lru_flags);
+	int ret;
 
-	if (nfsd_file_hashtbl)
+	lockdep_assert_held(&nfsd_mutex);
+	if (test_and_set_bit(NFSD_FILE_CACHE_UP, &nfsd_file_flags) == 1)
 		return 0;
 
+	ret = rhltable_init(&nfsd_file_rhltable, &nfsd_file_rhash_params);
+	if (ret)
+		goto out;
+
+	ret = -ENOMEM;
 	nfsd_filecache_wq = alloc_workqueue("nfsd_filecache", 0, 0);
 	if (!nfsd_filecache_wq)
 		goto out;
 
-	nfsd_file_hashtbl = kcalloc(NFSD_FILE_HASH_SIZE,
-				sizeof(*nfsd_file_hashtbl), GFP_KERNEL);
-	if (!nfsd_file_hashtbl) {
-		pr_err("nfsd: unable to allocate nfsd_file_hashtbl\n");
-		goto out_err;
-	}
-
 	nfsd_file_slab = kmem_cache_create("nfsd_file",
 				sizeof(struct nfsd_file), 0, 0, NULL);
 	if (!nfsd_file_slab) {
@@ -681,7 +759,8 @@
 		goto out_shrinker;
 	}
 
-	nfsd_file_fsnotify_group = fsnotify_alloc_group(&nfsd_file_fsnotify_ops);
+	nfsd_file_fsnotify_group = fsnotify_alloc_group(&nfsd_file_fsnotify_ops,
+							FSNOTIFY_GROUP_NOFS);
 	if (IS_ERR(nfsd_file_fsnotify_group)) {
 		pr_err("nfsd: unable to create fsnotify group: %ld\n",
 			PTR_ERR(nfsd_file_fsnotify_group));
@@ -690,13 +769,10 @@
 		goto out_notifier;
 	}
 
-	for (i = 0; i < NFSD_FILE_HASH_SIZE; i++) {
-		INIT_HLIST_HEAD(&nfsd_file_hashtbl[i].nfb_head);
-		spin_lock_init(&nfsd_file_hashtbl[i].nfb_lock);
-	}
-
 	INIT_DELAYED_WORK(&nfsd_filecache_laundrette, nfsd_file_gc_worker);
 out:
+	if (ret)
+		clear_bit(NFSD_FILE_CACHE_UP, &nfsd_file_flags);
 	return ret;
 out_notifier:
 	lease_unregister_notifier(&nfsd_file_lease_notifier);
@@ -709,50 +785,47 @@
 	nfsd_file_slab = NULL;
 	kmem_cache_destroy(nfsd_file_mark_slab);
 	nfsd_file_mark_slab = NULL;
-	kfree(nfsd_file_hashtbl);
-	nfsd_file_hashtbl = NULL;
 	destroy_workqueue(nfsd_filecache_wq);
 	nfsd_filecache_wq = NULL;
+	rhltable_destroy(&nfsd_file_rhltable);
 	goto out;
 }
 
-/*
- * Note this can deadlock with nfsd_file_lru_cb.
+/**
+ * __nfsd_file_cache_purge: clean out the cache for shutdown
+ * @net: net-namespace to shut down the cache (may be NULL)
+ *
+ * Walk the nfsd_file cache and close out any that match @net. If @net is NULL,
+ * then close out everything. Called when an nfsd instance is being shut down,
+ * and when the exports table is flushed.
  */
-void
-nfsd_file_cache_purge(struct net *net)
+static void
+__nfsd_file_cache_purge(struct net *net)
 {
-	unsigned int		i;
-	struct nfsd_file	*nf;
-	struct hlist_node	*next;
+	struct rhashtable_iter iter;
+	struct nfsd_file *nf;
 	LIST_HEAD(dispose);
-	bool del;
 
-	if (!nfsd_file_hashtbl)
-		return;
+	rhltable_walk_enter(&nfsd_file_rhltable, &iter);
+	do {
+		rhashtable_walk_start(&iter);
 
-	for (i = 0; i < NFSD_FILE_HASH_SIZE; i++) {
-		struct nfsd_fcache_bucket *nfb = &nfsd_file_hashtbl[i];
+		nf = rhashtable_walk_next(&iter);
+		while (!IS_ERR_OR_NULL(nf)) {
+			if (!net || nf->nf_net == net)
+				nfsd_file_cond_queue(nf, &dispose);
+			nf = rhashtable_walk_next(&iter);
+		}
 
-		spin_lock(&nfb->nfb_lock);
-		hlist_for_each_entry_safe(nf, next, &nfb->nfb_head, nf_node) {
-			if (net && nf->nf_net != net)
-				continue;
-			del = nfsd_file_unhash_and_release_locked(nf, &dispose);
+		rhashtable_walk_stop(&iter);
+	} while (nf == ERR_PTR(-EAGAIN));
+	rhashtable_walk_exit(&iter);
 
-			/*
-			 * Deadlock detected! Something marked this entry as
-			 * unhased, but hasn't removed it from the hash list.
-			 */
-			WARN_ON_ONCE(!del);
-		}
-		spin_unlock(&nfb->nfb_lock);
-		nfsd_file_dispose_list(&dispose);
-	}
+	nfsd_file_dispose_list(&dispose);
 }
 
 static struct nfsd_fcache_disposal *
-nfsd_alloc_fcache_disposal(struct net *net)
+nfsd_alloc_fcache_disposal(void)
 {
 	struct nfsd_fcache_disposal *l;
 
@@ -760,7 +833,6 @@
 	if (!l)
 		return NULL;
 	INIT_WORK(&l->work, nfsd_file_delayed_close);
-	l->net = net;
 	spin_lock_init(&l->lock);
 	INIT_LIST_HEAD(&l->freeme);
 	return l;
@@ -769,61 +841,40 @@
 static void
 nfsd_free_fcache_disposal(struct nfsd_fcache_disposal *l)
 {
-	rcu_assign_pointer(l->net, NULL);
 	cancel_work_sync(&l->work);
 	nfsd_file_dispose_list(&l->freeme);
-	kfree_rcu(l, rcu);
-}
-
-static void
-nfsd_add_fcache_disposal(struct nfsd_fcache_disposal *l)
-{
-	spin_lock(&laundrette_lock);
-	list_add_tail_rcu(&l->list, &laundrettes);
-	spin_unlock(&laundrette_lock);
+	kfree(l);
 }
 
 static void
-nfsd_del_fcache_disposal(struct nfsd_fcache_disposal *l)
-{
-	spin_lock(&laundrette_lock);
-	list_del_rcu(&l->list);
-	spin_unlock(&laundrette_lock);
-}
-
-static int
-nfsd_alloc_fcache_disposal_net(struct net *net)
+nfsd_free_fcache_disposal_net(struct net *net)
 {
-	struct nfsd_fcache_disposal *l;
+	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
+	struct nfsd_fcache_disposal *l = nn->fcache_disposal;
 
-	l = nfsd_alloc_fcache_disposal(net);
-	if (!l)
-		return -ENOMEM;
-	nfsd_add_fcache_disposal(l);
-	return 0;
+	nfsd_free_fcache_disposal(l);
 }
 
-static void
-nfsd_free_fcache_disposal_net(struct net *net)
+int
+nfsd_file_cache_start_net(struct net *net)
 {
-	struct nfsd_fcache_disposal *l;
+	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 
-	rcu_read_lock();
-	list_for_each_entry_rcu(l, &laundrettes, list) {
-		if (l->net != net)
-			continue;
-		nfsd_del_fcache_disposal(l);
-		rcu_read_unlock();
-		nfsd_free_fcache_disposal(l);
-		return;
-	}
-	rcu_read_unlock();
+	nn->fcache_disposal = nfsd_alloc_fcache_disposal();
+	return nn->fcache_disposal ? 0 : -ENOMEM;
 }
 
-int
-nfsd_file_cache_start_net(struct net *net)
+/**
+ * nfsd_file_cache_purge - Remove all cache items associated with @net
+ * @net: target net namespace
+ *
+ */
+void
+nfsd_file_cache_purge(struct net *net)
 {
-	return nfsd_alloc_fcache_disposal_net(net);
+	lockdep_assert_held(&nfsd_mutex);
+	if (test_bit(NFSD_FILE_CACHE_UP, &nfsd_file_flags) == 1)
+		__nfsd_file_cache_purge(net);
 }
 
 void
@@ -836,7 +887,11 @@
 void
 nfsd_file_cache_shutdown(void)
 {
-	set_bit(NFSD_FILE_SHUTDOWN, &nfsd_file_lru_flags);
+	int i;
+
+	lockdep_assert_held(&nfsd_mutex);
+	if (test_and_clear_bit(NFSD_FILE_CACHE_UP, &nfsd_file_flags) == 0)
+		return;
 
 	lease_unregister_notifier(&nfsd_file_lease_notifier);
 	unregister_shrinker(&nfsd_file_shrinker);
@@ -845,7 +900,7 @@
 	 * calling nfsd_file_cache_purge
 	 */
 	cancel_delayed_work_sync(&nfsd_filecache_laundrette);
-	nfsd_file_cache_purge(NULL);
+	__nfsd_file_cache_purge(NULL);
 	list_lru_destroy(&nfsd_file_lru);
 	rcu_barrier();
 	fsnotify_put_group(nfsd_file_fsnotify_group);
@@ -855,240 +910,331 @@
 	fsnotify_wait_marks_destroyed();
 	kmem_cache_destroy(nfsd_file_mark_slab);
 	nfsd_file_mark_slab = NULL;
-	kfree(nfsd_file_hashtbl);
-	nfsd_file_hashtbl = NULL;
 	destroy_workqueue(nfsd_filecache_wq);
 	nfsd_filecache_wq = NULL;
-}
-
-static bool
-nfsd_match_cred(const struct cred *c1, const struct cred *c2)
-{
-	int i;
+	rhltable_destroy(&nfsd_file_rhltable);
 
-	if (!uid_eq(c1->fsuid, c2->fsuid))
-		return false;
-	if (!gid_eq(c1->fsgid, c2->fsgid))
-		return false;
-	if (c1->group_info == NULL || c2->group_info == NULL)
-		return c1->group_info == c2->group_info;
-	if (c1->group_info->ngroups != c2->group_info->ngroups)
-		return false;
-	for (i = 0; i < c1->group_info->ngroups; i++) {
-		if (!gid_eq(c1->group_info->gid[i], c2->group_info->gid[i]))
-			return false;
+	for_each_possible_cpu(i) {
+		per_cpu(nfsd_file_cache_hits, i) = 0;
+		per_cpu(nfsd_file_acquisitions, i) = 0;
+		per_cpu(nfsd_file_releases, i) = 0;
+		per_cpu(nfsd_file_total_age, i) = 0;
+		per_cpu(nfsd_file_evictions, i) = 0;
 	}
-	return true;
 }
 
 static struct nfsd_file *
-nfsd_file_find_locked(struct inode *inode, unsigned int may_flags,
-			unsigned int hashval, struct net *net)
+nfsd_file_lookup_locked(const struct net *net, const struct cred *cred,
+			struct inode *inode, unsigned char need,
+			bool want_gc)
 {
+	struct rhlist_head *tmp, *list;
 	struct nfsd_file *nf;
-	unsigned char need = may_flags & NFSD_FILE_MAY_MASK;
 
-	hlist_for_each_entry_rcu(nf, &nfsd_file_hashtbl[hashval].nfb_head,
-				 nf_node, lockdep_is_held(&nfsd_file_hashtbl[hashval].nfb_lock)) {
+	list = rhltable_lookup(&nfsd_file_rhltable, &inode,
+			       nfsd_file_rhash_params);
+	rhl_for_each_entry_rcu(nf, tmp, list, nf_rlist) {
 		if (nf->nf_may != need)
 			continue;
-		if (nf->nf_inode != inode)
-			continue;
 		if (nf->nf_net != net)
 			continue;
-		if (!nfsd_match_cred(nf->nf_cred, current_cred()))
+		if (!nfsd_match_cred(nf->nf_cred, cred))
+			continue;
+		if (test_bit(NFSD_FILE_GC, &nf->nf_flags) != want_gc)
 			continue;
-		if (!test_bit(NFSD_FILE_HASHED, &nf->nf_flags))
+		if (test_bit(NFSD_FILE_HASHED, &nf->nf_flags) == 0)
+			continue;
+
+		if (!nfsd_file_get(nf))
 			continue;
-		if (nfsd_file_get(nf) != NULL)
-			return nf;
+		return nf;
 	}
 	return NULL;
 }
 
 /**
- * nfsd_file_is_cached - are there any cached open files for this fh?
- * @inode: inode of the file to check
+ * nfsd_file_is_cached - are there any cached open files for this inode?
+ * @inode: inode to check
+ *
+ * The lookup matches inodes in all net namespaces and is atomic wrt
+ * nfsd_file_acquire().
  *
- * Scan the hashtable for open files that match this fh. Returns true if there
- * are any, and false if not.
+ * Return values:
+ *   %true: filecache contains at least one file matching this inode
+ *   %false: filecache contains no files matching this inode
  */
 bool
 nfsd_file_is_cached(struct inode *inode)
 {
-	bool			ret = false;
-	struct nfsd_file	*nf;
-	unsigned int		hashval;
-
-        hashval = (unsigned int)hash_long(inode->i_ino, NFSD_FILE_HASH_BITS);
+	struct rhlist_head *tmp, *list;
+	struct nfsd_file *nf;
+	bool ret = false;
 
 	rcu_read_lock();
-	hlist_for_each_entry_rcu(nf, &nfsd_file_hashtbl[hashval].nfb_head,
-				 nf_node) {
-		if (inode == nf->nf_inode) {
+	list = rhltable_lookup(&nfsd_file_rhltable, &inode,
+			       nfsd_file_rhash_params);
+	rhl_for_each_entry_rcu(nf, tmp, list, nf_rlist)
+		if (test_bit(NFSD_FILE_GC, &nf->nf_flags)) {
 			ret = true;
 			break;
 		}
-	}
 	rcu_read_unlock();
-	trace_nfsd_file_is_cached(inode, hashval, (int)ret);
+
+	trace_nfsd_file_is_cached(inode, (int)ret);
 	return ret;
 }
 
-__be32
-nfsd_file_acquire(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		  unsigned int may_flags, struct nfsd_file **pnf)
+static __be32
+nfsd_file_do_acquire(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		     unsigned int may_flags, struct file *file,
+		     struct nfsd_file **pnf, bool want_gc)
 {
-	__be32	status;
+	unsigned char need = may_flags & NFSD_FILE_MAY_MASK;
 	struct net *net = SVC_NET(rqstp);
-	struct nfsd_file *nf, *new;
+	struct nfsd_file *new, *nf;
+	const struct cred *cred;
+	bool open_retry = true;
 	struct inode *inode;
-	unsigned int hashval;
-	bool retry = true;
+	__be32 status;
+	int ret;
 
-	/* FIXME: skip this if fh_dentry is already set? */
 	status = fh_verify(rqstp, fhp, S_IFREG,
 				may_flags|NFSD_MAY_OWNER_OVERRIDE);
 	if (status != nfs_ok)
 		return status;
-
 	inode = d_inode(fhp->fh_dentry);
-	hashval = (unsigned int)hash_long(inode->i_ino, NFSD_FILE_HASH_BITS);
+	cred = get_current_cred();
+
 retry:
 	rcu_read_lock();
-	nf = nfsd_file_find_locked(inode, may_flags, hashval, net);
+	nf = nfsd_file_lookup_locked(net, cred, inode, need, want_gc);
 	rcu_read_unlock();
-	if (nf)
+
+	if (nf) {
+		/*
+		 * If the nf is on the LRU then it holds an extra reference
+		 * that must be put if it's removed. It had better not be
+		 * the last one however, since we should hold another.
+		 */
+		if (nfsd_file_lru_remove(nf))
+			WARN_ON_ONCE(refcount_dec_and_test(&nf->nf_ref));
 		goto wait_for_construction;
+	}
 
-	new = nfsd_file_alloc(inode, may_flags, hashval, net);
+	new = nfsd_file_alloc(net, inode, need, want_gc);
 	if (!new) {
-		trace_nfsd_file_acquire(rqstp, hashval, inode, may_flags,
-					NULL, nfserr_jukebox);
-		return nfserr_jukebox;
+		status = nfserr_jukebox;
+		goto out;
 	}
 
-	spin_lock(&nfsd_file_hashtbl[hashval].nfb_lock);
-	nf = nfsd_file_find_locked(inode, may_flags, hashval, net);
-	if (nf == NULL)
+	rcu_read_lock();
+	spin_lock(&inode->i_lock);
+	nf = nfsd_file_lookup_locked(net, cred, inode, need, want_gc);
+	if (unlikely(nf)) {
+		spin_unlock(&inode->i_lock);
+		rcu_read_unlock();
+		nfsd_file_slab_free(&new->nf_rcu);
+		goto wait_for_construction;
+	}
+	nf = new;
+	ret = rhltable_insert(&nfsd_file_rhltable, &nf->nf_rlist,
+			      nfsd_file_rhash_params);
+	spin_unlock(&inode->i_lock);
+	rcu_read_unlock();
+	if (likely(ret == 0))
 		goto open_file;
-	spin_unlock(&nfsd_file_hashtbl[hashval].nfb_lock);
-	nfsd_file_slab_free(&new->nf_rcu);
+
+	trace_nfsd_file_insert_err(rqstp, inode, may_flags, ret);
+	status = nfserr_jukebox;
+	goto construction_err;
 
 wait_for_construction:
 	wait_on_bit(&nf->nf_flags, NFSD_FILE_PENDING, TASK_UNINTERRUPTIBLE);
 
 	/* Did construction of this file fail? */
 	if (!test_bit(NFSD_FILE_HASHED, &nf->nf_flags)) {
-		if (!retry) {
+		trace_nfsd_file_cons_err(rqstp, inode, may_flags, nf);
+		if (!open_retry) {
 			status = nfserr_jukebox;
-			goto out;
+			goto construction_err;
 		}
-		retry = false;
-		nfsd_file_put_noref(nf);
+		nfsd_file_put(nf);
+		open_retry = false;
 		goto retry;
 	}
-
 	this_cpu_inc(nfsd_file_cache_hits);
 
-	if (!(may_flags & NFSD_MAY_NOT_BREAK_LEASE)) {
-		bool write = (may_flags & NFSD_MAY_WRITE);
-
-		if (test_bit(NFSD_FILE_BREAK_READ, &nf->nf_flags) ||
-		    (test_bit(NFSD_FILE_BREAK_WRITE, &nf->nf_flags) && write)) {
-			status = nfserrno(nfsd_open_break_lease(
-					file_inode(nf->nf_file), may_flags));
-			if (status == nfs_ok) {
-				clear_bit(NFSD_FILE_BREAK_READ, &nf->nf_flags);
-				if (write)
-					clear_bit(NFSD_FILE_BREAK_WRITE,
-						  &nf->nf_flags);
-			}
-		}
+	status = nfserrno(nfsd_open_break_lease(file_inode(nf->nf_file), may_flags));
+	if (status != nfs_ok) {
+		nfsd_file_put(nf);
+		nf = NULL;
 	}
+
 out:
 	if (status == nfs_ok) {
+		this_cpu_inc(nfsd_file_acquisitions);
+		nfsd_file_check_write_error(nf);
 		*pnf = nf;
-	} else {
-		nfsd_file_put(nf);
-		nf = NULL;
 	}
-
-	trace_nfsd_file_acquire(rqstp, hashval, inode, may_flags, nf, status);
+	put_cred(cred);
+	trace_nfsd_file_acquire(rqstp, inode, may_flags, nf, status);
 	return status;
-open_file:
-	nf = new;
-	/* Take reference for the hashtable */
-	refcount_inc(&nf->nf_ref);
-	__set_bit(NFSD_FILE_HASHED, &nf->nf_flags);
-	__set_bit(NFSD_FILE_PENDING, &nf->nf_flags);
-	list_lru_add(&nfsd_file_lru, &nf->nf_lru);
-	hlist_add_head_rcu(&nf->nf_node, &nfsd_file_hashtbl[hashval].nfb_head);
-	++nfsd_file_hashtbl[hashval].nfb_count;
-	nfsd_file_hashtbl[hashval].nfb_maxcount = max(nfsd_file_hashtbl[hashval].nfb_maxcount,
-			nfsd_file_hashtbl[hashval].nfb_count);
-	spin_unlock(&nfsd_file_hashtbl[hashval].nfb_lock);
-	if (atomic_long_inc_return(&nfsd_filecache_count) >= NFSD_FILE_LRU_THRESHOLD)
-		nfsd_file_gc();
 
-	nf->nf_mark = nfsd_file_mark_find_or_create(nf);
-	if (nf->nf_mark)
-		status = nfsd_open_verified(rqstp, fhp, S_IFREG,
-				may_flags, &nf->nf_file);
-	else
+open_file:
+	trace_nfsd_file_alloc(nf);
+	nf->nf_mark = nfsd_file_mark_find_or_create(nf, inode);
+	if (nf->nf_mark) {
+		if (file) {
+			get_file(file);
+			nf->nf_file = file;
+			status = nfs_ok;
+			trace_nfsd_file_opened(nf, status);
+		} else {
+			status = nfsd_open_verified(rqstp, fhp, may_flags,
+						    &nf->nf_file);
+			trace_nfsd_file_open(nf, status);
+		}
+	} else
 		status = nfserr_jukebox;
 	/*
 	 * If construction failed, or we raced with a call to unlink()
 	 * then unhash.
 	 */
-	if (status != nfs_ok || inode->i_nlink == 0) {
-		bool do_free;
-		spin_lock(&nfsd_file_hashtbl[hashval].nfb_lock);
-		do_free = nfsd_file_unhash(nf);
-		spin_unlock(&nfsd_file_hashtbl[hashval].nfb_lock);
-		if (do_free)
-			nfsd_file_put_noref(nf);
-	}
-	clear_bit_unlock(NFSD_FILE_PENDING, &nf->nf_flags);
-	smp_mb__after_atomic();
-	wake_up_bit(&nf->nf_flags, NFSD_FILE_PENDING);
+	if (status != nfs_ok || inode->i_nlink == 0)
+		nfsd_file_unhash(nf);
+	clear_and_wake_up_bit(NFSD_FILE_PENDING, &nf->nf_flags);
+	if (status == nfs_ok)
+		goto out;
+
+construction_err:
+	if (refcount_dec_and_test(&nf->nf_ref))
+		nfsd_file_free(nf);
+	nf = NULL;
 	goto out;
 }
 
+/**
+ * nfsd_file_acquire_gc - Get a struct nfsd_file with an open file
+ * @rqstp: the RPC transaction being executed
+ * @fhp: the NFS filehandle of the file to be opened
+ * @may_flags: NFSD_MAY_ settings for the file
+ * @pnf: OUT: new or found "struct nfsd_file" object
+ *
+ * The nfsd_file object returned by this API is reference-counted
+ * and garbage-collected. The object is retained for a few
+ * seconds after the final nfsd_file_put() in case the caller
+ * wants to re-use it.
+ *
+ * Return values:
+ *   %nfs_ok - @pnf points to an nfsd_file with its reference
+ *   count boosted.
+ *
+ * On error, an nfsstat value in network byte order is returned.
+ */
+__be32
+nfsd_file_acquire_gc(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		     unsigned int may_flags, struct nfsd_file **pnf)
+{
+	return nfsd_file_do_acquire(rqstp, fhp, may_flags, NULL, pnf, true);
+}
+
+/**
+ * nfsd_file_acquire - Get a struct nfsd_file with an open file
+ * @rqstp: the RPC transaction being executed
+ * @fhp: the NFS filehandle of the file to be opened
+ * @may_flags: NFSD_MAY_ settings for the file
+ * @pnf: OUT: new or found "struct nfsd_file" object
+ *
+ * The nfsd_file_object returned by this API is reference-counted
+ * but not garbage-collected. The object is unhashed after the
+ * final nfsd_file_put().
+ *
+ * Return values:
+ *   %nfs_ok - @pnf points to an nfsd_file with its reference
+ *   count boosted.
+ *
+ * On error, an nfsstat value in network byte order is returned.
+ */
+__be32
+nfsd_file_acquire(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		  unsigned int may_flags, struct nfsd_file **pnf)
+{
+	return nfsd_file_do_acquire(rqstp, fhp, may_flags, NULL, pnf, false);
+}
+
+/**
+ * nfsd_file_acquire_opened - Get a struct nfsd_file using existing open file
+ * @rqstp: the RPC transaction being executed
+ * @fhp: the NFS filehandle of the file just created
+ * @may_flags: NFSD_MAY_ settings for the file
+ * @file: cached, already-open file (may be NULL)
+ * @pnf: OUT: new or found "struct nfsd_file" object
+ *
+ * Acquire a nfsd_file object that is not GC'ed. If one doesn't already exist,
+ * and @file is non-NULL, use it to instantiate a new nfsd_file instead of
+ * opening a new one.
+ *
+ * Return values:
+ *   %nfs_ok - @pnf points to an nfsd_file with its reference
+ *   count boosted.
+ *
+ * On error, an nfsstat value in network byte order is returned.
+ */
+__be32
+nfsd_file_acquire_opened(struct svc_rqst *rqstp, struct svc_fh *fhp,
+			 unsigned int may_flags, struct file *file,
+			 struct nfsd_file **pnf)
+{
+	return nfsd_file_do_acquire(rqstp, fhp, may_flags, file, pnf, false);
+}
+
 /*
  * Note that fields may be added, removed or reordered in the future. Programs
  * scraping this file for info should test the labels to ensure they're
  * getting the correct field.
  */
-static int nfsd_file_cache_stats_show(struct seq_file *m, void *v)
+int nfsd_file_cache_stats_show(struct seq_file *m, void *v)
 {
-	unsigned int i, count = 0, longest = 0;
-	unsigned long hits = 0;
+	unsigned long releases = 0, evictions = 0;
+	unsigned long hits = 0, acquisitions = 0;
+	unsigned int i, count = 0, buckets = 0;
+	unsigned long lru = 0, total_age = 0;
 
-	/*
-	 * No need for spinlocks here since we're not terribly interested in
-	 * accuracy. We do take the nfsd_mutex simply to ensure that we
-	 * don't end up racing with server shutdown
-	 */
+	/* Serialize with server shutdown */
 	mutex_lock(&nfsd_mutex);
-	if (nfsd_file_hashtbl) {
-		for (i = 0; i < NFSD_FILE_HASH_SIZE; i++) {
-			count += nfsd_file_hashtbl[i].nfb_count;
-			longest = max(longest, nfsd_file_hashtbl[i].nfb_count);
-		}
+	if (test_bit(NFSD_FILE_CACHE_UP, &nfsd_file_flags) == 1) {
+		struct bucket_table *tbl;
+		struct rhashtable *ht;
+
+		lru = list_lru_count(&nfsd_file_lru);
+
+		rcu_read_lock();
+		ht = &nfsd_file_rhltable.ht;
+		count = atomic_read(&ht->nelems);
+		tbl = rht_dereference_rcu(ht->tbl, ht);
+		buckets = tbl->size;
+		rcu_read_unlock();
 	}
 	mutex_unlock(&nfsd_mutex);
 
-	for_each_possible_cpu(i)
+	for_each_possible_cpu(i) {
 		hits += per_cpu(nfsd_file_cache_hits, i);
+		acquisitions += per_cpu(nfsd_file_acquisitions, i);
+		releases += per_cpu(nfsd_file_releases, i);
+		total_age += per_cpu(nfsd_file_total_age, i);
+		evictions += per_cpu(nfsd_file_evictions, i);
+	}
 
-	seq_printf(m, "total entries: %u\n", count);
-	seq_printf(m, "longest chain: %u\n", longest);
+	seq_printf(m, "total inodes:  %u\n", count);
+	seq_printf(m, "hash buckets:  %u\n", buckets);
+	seq_printf(m, "lru entries:   %lu\n", lru);
 	seq_printf(m, "cache hits:    %lu\n", hits);
+	seq_printf(m, "acquisitions:  %lu\n", acquisitions);
+	seq_printf(m, "releases:      %lu\n", releases);
+	seq_printf(m, "evictions:     %lu\n", evictions);
+	if (releases)
+		seq_printf(m, "mean age (ms): %ld\n", total_age / releases);
+	else
+		seq_printf(m, "mean age (ms): -\n");
 	return 0;
 }
-
-int nfsd_file_cache_stats_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, nfsd_file_cache_stats_show, NULL);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/filecache.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/filecache.h
@@ -29,24 +29,24 @@
  * never be dereferenced, only used for comparison.
  */
 struct nfsd_file {
-	struct hlist_node	nf_node;
-	struct list_head	nf_lru;
-	struct rcu_head		nf_rcu;
+	struct rhlist_head	nf_rlist;
+	void			*nf_inode;
 	struct file		*nf_file;
 	const struct cred	*nf_cred;
 	struct net		*nf_net;
 #define NFSD_FILE_HASHED	(0)
 #define NFSD_FILE_PENDING	(1)
-#define NFSD_FILE_BREAK_READ	(2)
-#define NFSD_FILE_BREAK_WRITE	(3)
-#define NFSD_FILE_REFERENCED	(4)
+#define NFSD_FILE_REFERENCED	(2)
+#define NFSD_FILE_GC		(3)
 	unsigned long		nf_flags;
-	struct inode		*nf_inode;
-	unsigned int		nf_hashval;
 	refcount_t		nf_ref;
 	unsigned char		nf_may;
+
 	struct nfsd_file_mark	*nf_mark;
-	struct rw_semaphore	nf_rwsem;
+	struct list_head	nf_lru;
+	struct list_head	nf_gc;
+	struct rcu_head		nf_rcu;
+	ktime_t			nf_birthtime;
 };
 
 int nfsd_file_cache_init(void);
@@ -58,7 +58,12 @@
 struct nfsd_file *nfsd_file_get(struct nfsd_file *nf);
 void nfsd_file_close_inode_sync(struct inode *inode);
 bool nfsd_file_is_cached(struct inode *inode);
+__be32 nfsd_file_acquire_gc(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		  unsigned int may_flags, struct nfsd_file **nfp);
 __be32 nfsd_file_acquire(struct svc_rqst *rqstp, struct svc_fh *fhp,
 		  unsigned int may_flags, struct nfsd_file **nfp);
-int	nfsd_file_cache_stats_open(struct inode *, struct file *);
+__be32 nfsd_file_acquire_opened(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		  unsigned int may_flags, struct file *file,
+		  struct nfsd_file **nfp);
+int nfsd_file_cache_stats_show(struct seq_file *m, void *v);
 #endif /* _FS_NFSD_FILECACHE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/flexfilelayout.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/flexfilelayout.c
@@ -15,6 +15,7 @@
 
 #include "flexfilelayoutxdr.h"
 #include "pnfs.h"
+#include "vfs.h"
 
 #define NFSDDBG_FACILITY	NFSDDBG_PNFS
 
@@ -61,7 +62,7 @@
 		goto out_error;
 
 	fl->fh.size = fhp->fh_handle.fh_size;
-	memcpy(fl->fh.data, &fhp->fh_handle.fh_base, fl->fh.size);
+	memcpy(fl->fh.data, &fhp->fh_handle.fh_raw, fl->fh.size);
 
 	/* Give whole file layout segments */
 	seg->offset = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/flexfilelayoutxdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/flexfilelayoutxdr.c
@@ -85,6 +85,15 @@
 	int addr_len;
 	__be32 *p;
 
+	/*
+	 * See paragraph 5 of RFC 8881 S18.40.3.
+	 */
+	if (!gdp->gd_maxcount) {
+		if (xdr_stream_encode_u32(xdr, 0) != XDR_UNIT)
+			return nfserr_resource;
+		return nfs_ok;
+	}
+
 	/* len + padding for two strings */
 	addr_len = 16 + da->netaddr.netid_len + da->netaddr.addr_len;
 	ver_len = 20;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/lockd.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/lockd.c
@@ -35,7 +35,7 @@
 	/* must initialize before using! but maxsize doesn't matter */
 	fh_init(&fh,0);
 	fh.fh_handle.fh_size = f->size;
-	memcpy((char*)&fh.fh_handle.fh_base, f->data, f->size);
+	memcpy(&fh.fh_handle.fh_raw, f->data, f->size);
 	fh.fh_export = NULL;
 
 	access = (mode == O_WRONLY) ? NFSD_MAY_WRITE : NFSD_MAY_READ;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/netns.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/netns.h
@@ -10,7 +10,10 @@
 
 #include <net/net_namespace.h>
 #include <net/netns/generic.h>
+#include <linux/nfs4.h>
 #include <linux/percpu_counter.h>
+#include <linux/siphash.h>
+#include <linux/sunrpc/stats.h>
 
 /* Hash tables for nfs4_clientid state */
 #define CLIENT_HASH_BITS                 4
@@ -24,10 +27,22 @@
 
 enum {
 	/* cache misses due only to checksum comparison failures */
-	NFSD_NET_PAYLOAD_MISSES,
+	NFSD_STATS_PAYLOAD_MISSES,
 	/* amount of memory (in bytes) currently consumed by the DRC */
-	NFSD_NET_DRC_MEM_USAGE,
-	NFSD_NET_COUNTERS_NUM
+	NFSD_STATS_DRC_MEM_USAGE,
+	NFSD_STATS_RC_HITS,		/* repcache hits */
+	NFSD_STATS_RC_MISSES,		/* repcache misses */
+	NFSD_STATS_RC_NOCACHE,		/* uncached reqs */
+	NFSD_STATS_FH_STALE,		/* FH stale error */
+	NFSD_STATS_IO_READ,		/* bytes returned to read requests */
+	NFSD_STATS_IO_WRITE,		/* bytes passed in write requests */
+#ifdef CONFIG_NFSD_V4
+	NFSD_STATS_FIRST_NFS4_OP,	/* count of individual nfsv4 operations */
+	NFSD_STATS_LAST_NFS4_OP = NFSD_STATS_FIRST_NFS4_OP + LAST_NFS4_OP,
+#define NFSD_STATS_NFS4_OP(op)	(NFSD_STATS_FIRST_NFS4_OP + (op))
+	NFSD_STATS_WDELEG_GETATTR,	/* count of getattr conflict with wdeleg */
+#endif
+	NFSD_STATS_COUNTERS_NUM
 };
 
 /*
@@ -108,9 +123,8 @@
 	bool nfsd_net_up;
 	bool lockd_up;
 
-	/* Time of server startup */
-	struct timespec64 nfssvc_boot;
-	seqlock_t boot_lock;
+	seqlock_t writeverf_lock;
+	unsigned char writeverf[8];
 
 	/*
 	 * Max number of connections this nfsd container will allow. Defaults
@@ -123,12 +137,13 @@
 	u32 clverifier_counter;
 
 	struct svc_serv *nfsd_serv;
-
-	wait_queue_head_t ntf_wq;
-	atomic_t ntf_refcnt;
-
-	/* Allow umount to wait for nfsd state cleanup */
-	struct completion nfsd_shutdown_complete;
+	/* When a listening socket is added to nfsd, keep_active is set
+	 * and this justifies a reference on nfsd_serv.  This stops
+	 * nfsd_serv from being freed.  When the number of threads is
+	 * set, keep_active is cleared and the reference is dropped.  So
+	 * when the last thread exits, the service will be destroyed.
+	 */
+	int keep_active;
 
 	/*
 	 * clientid and stateid data for construction of net unique COPY
@@ -137,6 +152,7 @@
 	u32		s2s_cp_cl_id;
 	struct idr	s2s_cp_stateids;
 	spinlock_t	s2s_cp_lock;
+	atomic_t	pending_async_copies;
 
 	/*
 	 * Version information
@@ -167,7 +183,10 @@
 	atomic_t                 num_drc_entries;
 
 	/* Per-netns stats counters */
-	struct percpu_counter    counter[NFSD_NET_COUNTERS_NUM];
+	struct percpu_counter    counter[NFSD_STATS_COUNTERS_NUM];
+
+	/* sunrpc svc stats */
+	struct svc_stat          nfsd_svcstats;
 
 	/* longest hash chain seen */
 	unsigned int             longest_chain;
@@ -184,6 +203,17 @@
 
 	/* utsname taken from the process that starts the server */
 	char			nfsd_name[UNX_MAXNODENAME+1];
+
+	struct nfsd_fcache_disposal *fcache_disposal;
+
+	siphash_key_t		siphash_key;
+
+	atomic_t		nfs4_client_count;
+	int			nfs4_max_clients;
+
+	atomic_t		nfsd_courtesy_clients;
+	struct shrinker		nfsd_client_shrinker;
+	struct work_struct	nfsd_shrinker_work;
 };
 
 /* Simple check to find out if a given net was properly initialized */
@@ -193,6 +223,6 @@
 
 extern unsigned int nfsd_net_id;
 
-void nfsd_copy_boot_verifier(__be32 verf[2], struct nfsd_net *nn);
-void nfsd_reset_boot_verifier(struct nfsd_net *nn);
+void nfsd_copy_write_verifier(__be32 verf[2], struct nfsd_net *nn);
+void nfsd_reset_write_verifier(struct nfsd_net *nn);
 #endif /* __NFSD_NETNS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs2acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs2acl.c
@@ -84,6 +84,8 @@
 fail:
 	posix_acl_release(resp->acl_access);
 	posix_acl_release(resp->acl_default);
+	resp->acl_access = NULL;
+	resp->acl_default = NULL;
 	goto out;
 }
 
@@ -111,7 +113,7 @@
 	if (error)
 		goto out_errno;
 
-	fh_lock(fh);
+	inode_lock(inode);
 
 	error = set_posix_acl(&init_user_ns, inode, ACL_TYPE_ACCESS,
 			      argp->acl_access);
@@ -122,7 +124,7 @@
 	if (error)
 		goto out_drop_lock;
 
-	fh_unlock(fh);
+	inode_unlock(inode);
 
 	fh_drop_write(fh);
 
@@ -136,7 +138,7 @@
 	return rpc_success;
 
 out_drop_lock:
-	fh_unlock(fh);
+	inode_unlock(inode);
 	fh_drop_write(fh);
 out_errno:
 	resp->status = nfserrno(error);
@@ -188,51 +190,51 @@
  * XDR decode functions
  */
 
-static int nfsaclsvc_decode_getaclargs(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfsaclsvc_decode_getaclargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_getaclargs *argp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_fhandle(xdr, &argp->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->mask) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-static int nfsaclsvc_decode_setaclargs(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfsaclsvc_decode_setaclargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_setaclargs *argp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_fhandle(xdr, &argp->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->mask) < 0)
-		return 0;
+		return false;
 	if (argp->mask & ~NFS_ACL_MASK)
-		return 0;
+		return false;
 	if (!nfs_stream_decode_acl(xdr, NULL, (argp->mask & NFS_ACL) ?
 				   &argp->acl_access : NULL))
-		return 0;
+		return false;
 	if (!nfs_stream_decode_acl(xdr, NULL, (argp->mask & NFS_DFACL) ?
 				   &argp->acl_default : NULL))
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-static int nfsaclsvc_decode_accessargs(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfsaclsvc_decode_accessargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_accessargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_fhandle(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->access) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 /*
@@ -240,63 +242,53 @@
  */
 
 /* GETACL */
-static int nfsaclsvc_encode_getaclres(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfsaclsvc_encode_getaclres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_getaclres *resp = rqstp->rq_resp;
 	struct dentry *dentry = resp->fh.fh_dentry;
 	struct inode *inode;
-	int w;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 
 	if (dentry == NULL || d_really_is_negative(dentry))
-		return 1;
+		return true;
 	inode = d_inode(dentry);
 
 	if (!svcxdr_encode_fattr(rqstp, xdr, &resp->fh, &resp->stat))
-		return 0;
+		return false;
 	if (xdr_stream_encode_u32(xdr, resp->mask) < 0)
-		return 0;
-
-	rqstp->rq_res.page_len = w = nfsacl_size(
-		(resp->mask & NFS_ACL)   ? resp->acl_access  : NULL,
-		(resp->mask & NFS_DFACL) ? resp->acl_default : NULL);
-	while (w > 0) {
-		if (!*(rqstp->rq_next_page++))
-			return 1;
-		w -= PAGE_SIZE;
-	}
+		return false;
 
 	if (!nfs_stream_encode_acl(xdr, inode, resp->acl_access,
 				   resp->mask & NFS_ACL, 0))
-		return 0;
+		return false;
 	if (!nfs_stream_encode_acl(xdr, inode, resp->acl_default,
 				   resp->mask & NFS_DFACL, NFS_ACL_DEFAULT))
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 /* ACCESS */
-static int nfsaclsvc_encode_accessres(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfsaclsvc_encode_accessres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_accessres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_fattr(rqstp, xdr, &resp->fh, &resp->stat))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->access) < 0)
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
 /*
@@ -331,6 +323,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST,
@@ -342,6 +335,7 @@
 		.pc_encode = nfsaclsvc_encode_getaclres,
 		.pc_release = nfsaclsvc_release_getacl,
 		.pc_argsize = sizeof(struct nfsd3_getaclargs),
+		.pc_argzero = sizeof(struct nfsd3_getaclargs),
 		.pc_ressize = sizeof(struct nfsd3_getaclres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+1+2*(1+ACL),
@@ -353,6 +347,7 @@
 		.pc_encode = nfssvc_encode_attrstatres,
 		.pc_release = nfssvc_release_attrstat,
 		.pc_argsize = sizeof(struct nfsd3_setaclargs),
+		.pc_argzero = sizeof(struct nfsd3_setaclargs),
 		.pc_ressize = sizeof(struct nfsd_attrstat),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+AT,
@@ -364,6 +359,7 @@
 		.pc_encode = nfssvc_encode_attrstatres,
 		.pc_release = nfssvc_release_attrstat,
 		.pc_argsize = sizeof(struct nfsd_fhandle),
+		.pc_argzero = sizeof(struct nfsd_fhandle),
 		.pc_ressize = sizeof(struct nfsd_attrstat),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+AT,
@@ -375,6 +371,7 @@
 		.pc_encode = nfsaclsvc_encode_accessres,
 		.pc_release = nfsaclsvc_release_access,
 		.pc_argsize = sizeof(struct nfsd3_accessargs),
+		.pc_argzero = sizeof(struct nfsd3_accessargs),
 		.pc_ressize = sizeof(struct nfsd3_accessres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+AT+1,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs3acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs3acl.c
@@ -76,6 +76,8 @@
 fail:
 	posix_acl_release(resp->acl_access);
 	posix_acl_release(resp->acl_default);
+	resp->acl_access = NULL;
+	resp->acl_default = NULL;
 	goto out;
 }
 
@@ -101,7 +103,7 @@
 	if (error)
 		goto out_errno;
 
-	fh_lock(fh);
+	inode_lock(inode);
 
 	error = set_posix_acl(&init_user_ns, inode, ACL_TYPE_ACCESS,
 			      argp->acl_access);
@@ -111,7 +113,7 @@
 			      argp->acl_default);
 
 out_drop_lock:
-	fh_unlock(fh);
+	inode_unlock(inode);
 	fh_drop_write(fh);
 out_errno:
 	resp->status = nfserrno(error);
@@ -127,38 +129,38 @@
  * XDR decode functions
  */
 
-static int nfs3svc_decode_getaclargs(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfs3svc_decode_getaclargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_getaclargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->mask) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-static int nfs3svc_decode_setaclargs(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfs3svc_decode_setaclargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_setaclargs *argp = rqstp->rq_argp;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &argp->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &argp->mask) < 0)
-		return 0;
+		return false;
 	if (argp->mask & ~NFS_ACL_MASK)
-		return 0;
+		return false;
 	if (!nfs_stream_decode_acl(xdr, NULL, (argp->mask & NFS_ACL) ?
 				   &argp->acl_access : NULL))
-		return 0;
+		return false;
 	if (!nfs_stream_decode_acl(xdr, NULL, (argp->mask & NFS_DFACL) ?
 				   &argp->acl_default : NULL))
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 /*
@@ -166,61 +168,43 @@
  */
 
 /* GETACL */
-static int nfs3svc_encode_getaclres(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfs3svc_encode_getaclres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_getaclres *resp = rqstp->rq_resp;
 	struct dentry *dentry = resp->fh.fh_dentry;
-	struct kvec *head = rqstp->rq_res.head;
 	struct inode *inode;
-	unsigned int base;
-	int n;
-	int w;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		inode = d_inode(dentry);
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->mask) < 0)
-			return 0;
+			return false;
 
-		base = (char *)xdr->p - (char *)head->iov_base;
-
-		rqstp->rq_res.page_len = w = nfsacl_size(
-			(resp->mask & NFS_ACL)   ? resp->acl_access  : NULL,
-			(resp->mask & NFS_DFACL) ? resp->acl_default : NULL);
-		while (w > 0) {
-			if (!*(rqstp->rq_next_page++))
-				return 0;
-			w -= PAGE_SIZE;
-		}
-
-		n = nfsacl_encode(&rqstp->rq_res, base, inode,
-				  resp->acl_access,
-				  resp->mask & NFS_ACL, 0);
-		if (n > 0)
-			n = nfsacl_encode(&rqstp->rq_res, base + n, inode,
-					  resp->acl_default,
-					  resp->mask & NFS_DFACL,
-					  NFS_ACL_DEFAULT);
-		if (n <= 0)
-			return 0;
+		if (!nfs_stream_encode_acl(xdr, inode, resp->acl_access,
+					   resp->mask & NFS_ACL, 0))
+			return false;
+		if (!nfs_stream_encode_acl(xdr, inode, resp->acl_default,
+					   resp->mask & NFS_DFACL,
+					   NFS_ACL_DEFAULT))
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* SETACL */
-static int nfs3svc_encode_setaclres(struct svc_rqst *rqstp, __be32 *p)
+static bool
+nfs3svc_encode_setaclres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_attrstat *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_nfsstat3(xdr, resp->status) &&
@@ -252,6 +236,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST,
@@ -263,6 +248,7 @@
 		.pc_encode = nfs3svc_encode_getaclres,
 		.pc_release = nfs3svc_release_getacl,
 		.pc_argsize = sizeof(struct nfsd3_getaclargs),
+		.pc_argzero = sizeof(struct nfsd3_getaclargs),
 		.pc_ressize = sizeof(struct nfsd3_getaclres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+1+2*(1+ACL),
@@ -274,6 +260,7 @@
 		.pc_encode = nfs3svc_encode_setaclres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_setaclargs),
+		.pc_argzero = sizeof(struct nfsd3_setaclargs),
 		.pc_ressize = sizeof(struct nfsd3_attrstat),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs3proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs3proc.c
@@ -8,10 +8,12 @@
 #include <linux/fs.h>
 #include <linux/ext2_fs.h>
 #include <linux/magic.h>
+#include <linux/namei.h>
 
 #include "cache.h"
 #include "xdr3.h"
 #include "vfs.h"
+#include "filecache.h"
 
 #define NFSDDBG_FACILITY		NFSDDBG_PROC
 
@@ -66,12 +68,15 @@
 {
 	struct nfsd3_sattrargs *argp = rqstp->rq_argp;
 	struct nfsd3_attrstat *resp = rqstp->rq_resp;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &argp->attrs,
+	};
 
 	dprintk("nfsd: SETATTR(3)  %s\n",
 				SVCFH_fmt(&argp->fh));
 
 	fh_copy(&resp->fh, &argp->fh);
-	resp->status = nfsd_setattr(rqstp, &resp->fh, &argp->attrs,
+	resp->status = nfsd_setattr(rqstp, &resp->fh, &attrs,
 				    argp->check_guard, argp->guardtime);
 	return rpc_success;
 }
@@ -146,17 +151,21 @@
 {
 	struct nfsd3_readargs *argp = rqstp->rq_argp;
 	struct nfsd3_readres *resp = rqstp->rq_resp;
-	u32 max_blocksize = svc_max_payload(rqstp);
 	unsigned int len;
 	int v;
 
-	argp->count = min_t(u32, argp->count, max_blocksize);
-
 	dprintk("nfsd: READ(3) %s %lu bytes at %Lu\n",
 				SVCFH_fmt(&argp->fh),
 				(unsigned long) argp->count,
 				(unsigned long long) argp->offset);
 
+	argp->count = min_t(u32, argp->count, svc_max_payload(rqstp));
+	argp->count = min_t(u32, argp->count, rqstp->rq_res.buflen);
+	if (argp->offset > (u64)OFFSET_MAX)
+		argp->offset = (u64)OFFSET_MAX;
+	if (argp->offset + argp->count > (u64)OFFSET_MAX)
+		argp->count = (u64)OFFSET_MAX - argp->offset;
+
 	v = 0;
 	len = argp->count;
 	resp->pages = rqstp->rq_next_page;
@@ -199,34 +208,154 @@
 				(unsigned long long) argp->offset,
 				argp->stable? " stable" : "");
 
+	resp->status = nfserr_fbig;
+	if (argp->offset > (u64)OFFSET_MAX ||
+	    argp->offset + argp->len > (u64)OFFSET_MAX)
+		return rpc_success;
+
 	fh_copy(&resp->fh, &argp->fh);
 	resp->committed = argp->stable;
-	nvecs = svc_fill_write_vector(rqstp, rqstp->rq_arg.pages,
-				      &argp->first, cnt);
-	if (!nvecs) {
-		resp->status = nfserr_io;
-		goto out;
-	}
+	nvecs = svc_fill_write_vector(rqstp, &argp->payload);
+
 	resp->status = nfsd_write(rqstp, &resp->fh, argp->offset,
 				  rqstp->rq_vec, nvecs, &cnt,
 				  resp->committed, resp->verf);
 	resp->count = cnt;
-out:
 	return rpc_success;
 }
 
 /*
- * With NFSv3, CREATE processing is a lot easier than with NFSv2.
- * At least in theory; we'll see how it fares in practice when the
- * first reports about SunOS compatibility problems start to pour in...
+ * Implement NFSv3's unchecked, guarded, and exclusive CREATE
+ * semantics for regular files. Except for the created file,
+ * this operation is stateless on the server.
+ *
+ * Upon return, caller must release @fhp and @resfhp.
  */
 static __be32
+nfsd3_create_file(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		  struct svc_fh *resfhp, struct nfsd3_createargs *argp)
+{
+	struct iattr *iap = &argp->attrs;
+	struct dentry *parent, *child;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= iap,
+	};
+	__u32 v_mtime, v_atime;
+	struct inode *inode;
+	__be32 status;
+	int host_err;
+
+	if (isdotent(argp->name, argp->len))
+		return nfserr_exist;
+	if (!(iap->ia_valid & ATTR_MODE))
+		iap->ia_mode = 0;
+
+	status = fh_verify(rqstp, fhp, S_IFDIR, NFSD_MAY_EXEC);
+	if (status != nfs_ok)
+		return status;
+
+	parent = fhp->fh_dentry;
+	inode = d_inode(parent);
+
+	host_err = fh_want_write(fhp);
+	if (host_err)
+		return nfserrno(host_err);
+
+	inode_lock_nested(inode, I_MUTEX_PARENT);
+
+	child = lookup_one_len(argp->name, parent, argp->len);
+	if (IS_ERR(child)) {
+		status = nfserrno(PTR_ERR(child));
+		goto out;
+	}
+
+	if (d_really_is_negative(child)) {
+		status = fh_verify(rqstp, fhp, S_IFDIR, NFSD_MAY_CREATE);
+		if (status != nfs_ok)
+			goto out;
+	}
+
+	status = fh_compose(resfhp, fhp->fh_export, child, fhp);
+	if (status != nfs_ok)
+		goto out;
+
+	v_mtime = 0;
+	v_atime = 0;
+	if (argp->createmode == NFS3_CREATE_EXCLUSIVE) {
+		u32 *verifier = (u32 *)argp->verf;
+
+		/*
+		 * Solaris 7 gets confused (bugid 4218508) if these have
+		 * the high bit set, as do xfs filesystems without the
+		 * "bigtime" feature. So just clear the high bits.
+		 */
+		v_mtime = verifier[0] & 0x7fffffff;
+		v_atime = verifier[1] & 0x7fffffff;
+	}
+
+	if (d_really_is_positive(child)) {
+		status = nfs_ok;
+
+		switch (argp->createmode) {
+		case NFS3_CREATE_UNCHECKED:
+			if (!d_is_reg(child))
+				break;
+			iap->ia_valid &= ATTR_SIZE;
+			goto set_attr;
+		case NFS3_CREATE_GUARDED:
+			status = nfserr_exist;
+			break;
+		case NFS3_CREATE_EXCLUSIVE:
+			if (d_inode(child)->i_mtime.tv_sec == v_mtime &&
+			    d_inode(child)->i_atime.tv_sec == v_atime &&
+			    d_inode(child)->i_size == 0) {
+				break;
+			}
+			status = nfserr_exist;
+		}
+		goto out;
+	}
+
+	if (!IS_POSIXACL(inode))
+		iap->ia_mode &= ~current_umask();
+
+	fh_fill_pre_attrs(fhp);
+	host_err = vfs_create(&init_user_ns, inode, child, iap->ia_mode, true);
+	if (host_err < 0) {
+		status = nfserrno(host_err);
+		goto out;
+	}
+	fh_fill_post_attrs(fhp);
+
+	/* A newly created file already has a file size of zero. */
+	if ((iap->ia_valid & ATTR_SIZE) && (iap->ia_size == 0))
+		iap->ia_valid &= ~ATTR_SIZE;
+	if (argp->createmode == NFS3_CREATE_EXCLUSIVE) {
+		iap->ia_valid = ATTR_MTIME | ATTR_ATIME |
+				ATTR_MTIME_SET | ATTR_ATIME_SET;
+		iap->ia_mtime.tv_sec = v_mtime;
+		iap->ia_atime.tv_sec = v_atime;
+		iap->ia_mtime.tv_nsec = 0;
+		iap->ia_atime.tv_nsec = 0;
+	}
+
+set_attr:
+	status = nfsd_create_setattr(rqstp, fhp, resfhp, &attrs);
+
+out:
+	inode_unlock(inode);
+	if (child && !IS_ERR(child))
+		dput(child);
+	fh_drop_write(fhp);
+	return status;
+}
+
+static __be32
 nfsd3_proc_create(struct svc_rqst *rqstp)
 {
 	struct nfsd3_createargs *argp = rqstp->rq_argp;
 	struct nfsd3_diropres *resp = rqstp->rq_resp;
-	svc_fh		*dirfhp, *newfhp = NULL;
-	struct iattr	*attr;
+	svc_fh *dirfhp, *newfhp;
 
 	dprintk("nfsd: CREATE(3)   %s %.*s\n",
 				SVCFH_fmt(&argp->fh),
@@ -235,21 +364,8 @@
 
 	dirfhp = fh_copy(&resp->dirfh, &argp->fh);
 	newfhp = fh_init(&resp->fh, NFS3_FHSIZE);
-	attr   = &argp->attrs;
-
-	/* Unfudge the mode bits */
-	attr->ia_mode &= ~S_IFMT;
-	if (!(attr->ia_valid & ATTR_MODE)) { 
-		attr->ia_valid |= ATTR_MODE;
-		attr->ia_mode = S_IFREG;
-	} else {
-		attr->ia_mode = (attr->ia_mode & ~S_IFMT) | S_IFREG;
-	}
 
-	/* Now create the file and set attributes */
-	resp->status = do_nfsd_create(rqstp, dirfhp, argp->name, argp->len,
-				      attr, newfhp, argp->createmode,
-				      (u32 *)argp->verf, NULL, NULL);
+	resp->status = nfsd3_create_file(rqstp, dirfhp, newfhp, argp);
 	return rpc_success;
 }
 
@@ -261,6 +377,9 @@
 {
 	struct nfsd3_createargs *argp = rqstp->rq_argp;
 	struct nfsd3_diropres *resp = rqstp->rq_resp;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &argp->attrs,
+	};
 
 	dprintk("nfsd: MKDIR(3)    %s %.*s\n",
 				SVCFH_fmt(&argp->fh),
@@ -271,8 +390,7 @@
 	fh_copy(&resp->dirfh, &argp->fh);
 	fh_init(&resp->fh, NFS3_FHSIZE);
 	resp->status = nfsd_create(rqstp, &resp->dirfh, argp->name, argp->len,
-				   &argp->attrs, S_IFDIR, 0, &resp->fh);
-	fh_unlock(&resp->dirfh);
+				   &attrs, S_IFDIR, 0, &resp->fh);
 	return rpc_success;
 }
 
@@ -281,6 +399,9 @@
 {
 	struct nfsd3_symlinkargs *argp = rqstp->rq_argp;
 	struct nfsd3_diropres *resp = rqstp->rq_resp;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &argp->attrs,
+	};
 
 	if (argp->tlen == 0) {
 		resp->status = nfserr_inval;
@@ -307,7 +428,7 @@
 	fh_copy(&resp->dirfh, &argp->ffh);
 	fh_init(&resp->fh, NFS3_FHSIZE);
 	resp->status = nfsd_symlink(rqstp, &resp->dirfh, argp->fname,
-				    argp->flen, argp->tname, &resp->fh);
+				    argp->flen, argp->tname, &attrs, &resp->fh);
 	kfree(argp->tname);
 out:
 	return rpc_success;
@@ -321,6 +442,9 @@
 {
 	struct nfsd3_mknodargs *argp = rqstp->rq_argp;
 	struct nfsd3_diropres  *resp = rqstp->rq_resp;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &argp->attrs,
+	};
 	int type;
 	dev_t	rdev = 0;
 
@@ -346,8 +470,7 @@
 
 	type = nfs3_ftypes[argp->ftype];
 	resp->status = nfsd_create(rqstp, &resp->dirfh, argp->name, argp->len,
-				   &argp->attrs, type, rdev, &resp->fh);
-	fh_unlock(&resp->dirfh);
+				   &attrs, type, rdev, &resp->fh);
 out:
 	return rpc_success;
 }
@@ -370,7 +493,6 @@
 	fh_copy(&resp->fh, &argp->fh);
 	resp->status = nfsd_unlink(rqstp, &resp->fh, -S_IFDIR,
 				   argp->name, argp->len);
-	fh_unlock(&resp->fh);
 	return rpc_success;
 }
 
@@ -391,7 +513,6 @@
 	fh_copy(&resp->fh, &argp->fh);
 	resp->status = nfsd_unlink(rqstp, &resp->fh, S_IFDIR,
 				   argp->name, argp->len);
-	fh_unlock(&resp->fh);
 	return rpc_success;
 }
 
@@ -439,32 +560,22 @@
 
 static void nfsd3_init_dirlist_pages(struct svc_rqst *rqstp,
 				     struct nfsd3_readdirres *resp,
-				     int count)
+				     u32 count)
 {
 	struct xdr_buf *buf = &resp->dirlist;
 	struct xdr_stream *xdr = &resp->xdr;
-
-	count = min_t(u32, count, svc_max_payload(rqstp));
+	unsigned int sendbuf = min_t(unsigned int, rqstp->rq_res.buflen,
+				     svc_max_payload(rqstp));
 
 	memset(buf, 0, sizeof(*buf));
 
 	/* Reserve room for the NULL ptr & eof flag (-2 words) */
-	buf->buflen = count - XDR_UNIT * 2;
+	buf->buflen = clamp(count, (u32)(XDR_UNIT * 2), sendbuf);
+	buf->buflen -= XDR_UNIT * 2;
 	buf->pages = rqstp->rq_next_page;
-	while (count > 0) {
-		rqstp->rq_next_page++;
-		count -= PAGE_SIZE;
-	}
+	rqstp->rq_next_page += (buf->buflen + PAGE_SIZE - 1) >> PAGE_SHIFT;
 
-	/* This is xdr_init_encode(), but it assumes that
-	 * the head kvec has already been consumed. */
-	xdr_set_scratch_buffer(xdr, NULL, 0);
-	xdr->buf = buf;
-	xdr->page_ptr = buf->pages;
-	xdr->iov = NULL;
-	xdr->p = page_address(*buf->pages);
-	xdr->end = xdr->p + (PAGE_SIZE >> 2);
-	xdr->rqst = NULL;
+	xdr_init_encode_pages(xdr, buf, buf->pages,  NULL);
 }
 
 /*
@@ -653,20 +764,21 @@
 {
 	struct nfsd3_commitargs *argp = rqstp->rq_argp;
 	struct nfsd3_commitres *resp = rqstp->rq_resp;
+	struct nfsd_file *nf;
 
 	dprintk("nfsd: COMMIT(3)   %s %u@%Lu\n",
 				SVCFH_fmt(&argp->fh),
 				argp->count,
 				(unsigned long long) argp->offset);
 
-	if (argp->offset > NFS_OFFSET_MAX) {
-		resp->status = nfserr_inval;
-		goto out;
-	}
-
 	fh_copy(&resp->fh, &argp->fh);
-	resp->status = nfsd_commit(rqstp, &resp->fh, argp->offset,
+	resp->status = nfsd_file_acquire_gc(rqstp, &resp->fh, NFSD_MAY_WRITE |
+					    NFSD_MAY_NOT_BREAK_LEASE, &nf);
+	if (resp->status)
+		goto out;
+	resp->status = nfsd_commit(rqstp, &resp->fh, nf, argp->offset,
 				   argp->count, resp->verf);
+	nfsd_file_put(nf);
 out:
 	return rpc_success;
 }
@@ -697,6 +809,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST,
@@ -708,6 +821,7 @@
 		.pc_encode = nfs3svc_encode_getattrres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd_fhandle),
+		.pc_argzero = sizeof(struct nfsd_fhandle),
 		.pc_ressize = sizeof(struct nfsd3_attrstatres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+AT,
@@ -719,6 +833,7 @@
 		.pc_encode = nfs3svc_encode_wccstatres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_sattrargs),
+		.pc_argzero = sizeof(struct nfsd3_sattrargs),
 		.pc_ressize = sizeof(struct nfsd3_wccstatres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+WC,
@@ -730,6 +845,7 @@
 		.pc_encode = nfs3svc_encode_lookupres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_diropargs),
+		.pc_argzero = sizeof(struct nfsd3_diropargs),
 		.pc_ressize = sizeof(struct nfsd3_diropres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+FH+pAT+pAT,
@@ -741,6 +857,7 @@
 		.pc_encode = nfs3svc_encode_accessres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_accessargs),
+		.pc_argzero = sizeof(struct nfsd3_accessargs),
 		.pc_ressize = sizeof(struct nfsd3_accessres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT+1,
@@ -752,6 +869,7 @@
 		.pc_encode = nfs3svc_encode_readlinkres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd_fhandle),
+		.pc_argzero = sizeof(struct nfsd_fhandle),
 		.pc_ressize = sizeof(struct nfsd3_readlinkres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT+1+NFS3_MAXPATHLEN/4,
@@ -763,6 +881,7 @@
 		.pc_encode = nfs3svc_encode_readres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_readargs),
+		.pc_argzero = sizeof(struct nfsd3_readargs),
 		.pc_ressize = sizeof(struct nfsd3_readres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT+4+NFSSVC_MAXBLKSIZE/4,
@@ -774,6 +893,7 @@
 		.pc_encode = nfs3svc_encode_writeres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_writeargs),
+		.pc_argzero = sizeof(struct nfsd3_writeargs),
 		.pc_ressize = sizeof(struct nfsd3_writeres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+WC+4,
@@ -785,6 +905,7 @@
 		.pc_encode = nfs3svc_encode_createres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_createargs),
+		.pc_argzero = sizeof(struct nfsd3_createargs),
 		.pc_ressize = sizeof(struct nfsd3_createres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+(1+FH+pAT)+WC,
@@ -796,6 +917,7 @@
 		.pc_encode = nfs3svc_encode_createres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_mkdirargs),
+		.pc_argzero = sizeof(struct nfsd3_mkdirargs),
 		.pc_ressize = sizeof(struct nfsd3_createres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+(1+FH+pAT)+WC,
@@ -807,6 +929,7 @@
 		.pc_encode = nfs3svc_encode_createres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_symlinkargs),
+		.pc_argzero = sizeof(struct nfsd3_symlinkargs),
 		.pc_ressize = sizeof(struct nfsd3_createres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+(1+FH+pAT)+WC,
@@ -818,6 +941,7 @@
 		.pc_encode = nfs3svc_encode_createres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_mknodargs),
+		.pc_argzero = sizeof(struct nfsd3_mknodargs),
 		.pc_ressize = sizeof(struct nfsd3_createres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+(1+FH+pAT)+WC,
@@ -829,6 +953,7 @@
 		.pc_encode = nfs3svc_encode_wccstatres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_diropargs),
+		.pc_argzero = sizeof(struct nfsd3_diropargs),
 		.pc_ressize = sizeof(struct nfsd3_wccstatres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+WC,
@@ -840,6 +965,7 @@
 		.pc_encode = nfs3svc_encode_wccstatres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_diropargs),
+		.pc_argzero = sizeof(struct nfsd3_diropargs),
 		.pc_ressize = sizeof(struct nfsd3_wccstatres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+WC,
@@ -851,6 +977,7 @@
 		.pc_encode = nfs3svc_encode_renameres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_renameargs),
+		.pc_argzero = sizeof(struct nfsd3_renameargs),
 		.pc_ressize = sizeof(struct nfsd3_renameres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+WC+WC,
@@ -862,6 +989,7 @@
 		.pc_encode = nfs3svc_encode_linkres,
 		.pc_release = nfs3svc_release_fhandle2,
 		.pc_argsize = sizeof(struct nfsd3_linkargs),
+		.pc_argzero = sizeof(struct nfsd3_linkargs),
 		.pc_ressize = sizeof(struct nfsd3_linkres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+pAT+WC,
@@ -873,6 +1001,7 @@
 		.pc_encode = nfs3svc_encode_readdirres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_readdirargs),
+		.pc_argzero = sizeof(struct nfsd3_readdirargs),
 		.pc_ressize = sizeof(struct nfsd3_readdirres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_name = "READDIR",
@@ -883,6 +1012,7 @@
 		.pc_encode = nfs3svc_encode_readdirres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_readdirplusargs),
+		.pc_argzero = sizeof(struct nfsd3_readdirplusargs),
 		.pc_ressize = sizeof(struct nfsd3_readdirres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_name = "READDIRPLUS",
@@ -892,6 +1022,7 @@
 		.pc_decode = nfs3svc_decode_fhandleargs,
 		.pc_encode = nfs3svc_encode_fsstatres,
 		.pc_argsize = sizeof(struct nfsd3_fhandleargs),
+		.pc_argzero = sizeof(struct nfsd3_fhandleargs),
 		.pc_ressize = sizeof(struct nfsd3_fsstatres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT+2*6+1,
@@ -902,6 +1033,7 @@
 		.pc_decode = nfs3svc_decode_fhandleargs,
 		.pc_encode = nfs3svc_encode_fsinfores,
 		.pc_argsize = sizeof(struct nfsd3_fhandleargs),
+		.pc_argzero = sizeof(struct nfsd3_fhandleargs),
 		.pc_ressize = sizeof(struct nfsd3_fsinfores),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT+12,
@@ -912,6 +1044,7 @@
 		.pc_decode = nfs3svc_decode_fhandleargs,
 		.pc_encode = nfs3svc_encode_pathconfres,
 		.pc_argsize = sizeof(struct nfsd3_fhandleargs),
+		.pc_argzero = sizeof(struct nfsd3_fhandleargs),
 		.pc_ressize = sizeof(struct nfsd3_pathconfres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+pAT+6,
@@ -923,6 +1056,7 @@
 		.pc_encode = nfs3svc_encode_commitres,
 		.pc_release = nfs3svc_release_fhandle,
 		.pc_argsize = sizeof(struct nfsd3_commitargs),
+		.pc_argzero = sizeof(struct nfsd3_commitargs),
 		.pc_ressize = sizeof(struct nfsd3_commitres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+WC+2,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs3xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs3xdr.c
@@ -92,7 +92,7 @@
 		return false;
 	fh_init(fhp, NFS3_FHSIZE);
 	fhp->fh_handle.fh_size = size;
-	memcpy(&fhp->fh_handle.fh_base, p, size);
+	memcpy(&fhp->fh_handle.fh_raw, p, size);
 
 	return true;
 }
@@ -131,7 +131,7 @@
 	*p++ = cpu_to_be32(size);
 	if (size)
 		p[XDR_QUADLEN(size) - 1] = 0;
-	memcpy(p, &fhp->fh_handle.fh_base, size);
+	memcpy(p, &fhp->fh_handle.fh_raw, size);
 
 	return true;
 }
@@ -254,7 +254,7 @@
 		if (xdr_stream_decode_u64(xdr, &newsize) < 0)
 			return false;
 		iap->ia_valid |= ATTR_SIZE;
-		iap->ia_size = min_t(u64, newsize, NFS_OFFSET_MAX);
+		iap->ia_size = newsize;
 	}
 	if (xdr_stream_decode_u32(xdr, &set_it) < 0)
 		return false;
@@ -487,88 +487,21 @@
 	return true;
 }
 
-static bool fs_supports_change_attribute(struct super_block *sb)
-{
-	return sb->s_flags & SB_I_VERSION || sb->s_export_op->fetch_iversion;
-}
-
-/*
- * Fill in the pre_op attr for the wcc data
- */
-void fill_pre_wcc(struct svc_fh *fhp)
-{
-	struct inode    *inode;
-	struct kstat	stat;
-	bool v4 = (fhp->fh_maxsize == NFS4_FHSIZE);
-
-	if (fhp->fh_no_wcc || fhp->fh_pre_saved)
-		return;
-	inode = d_inode(fhp->fh_dentry);
-	if (fs_supports_change_attribute(inode->i_sb) || !v4) {
-		__be32 err = fh_getattr(fhp, &stat);
-
-		if (err) {
-			/* Grab the times from inode anyway */
-			stat.mtime = inode->i_mtime;
-			stat.ctime = inode->i_ctime;
-			stat.size  = inode->i_size;
-		}
-		fhp->fh_pre_mtime = stat.mtime;
-		fhp->fh_pre_ctime = stat.ctime;
-		fhp->fh_pre_size  = stat.size;
-	}
-	if (v4)
-		fhp->fh_pre_change = nfsd4_change_attribute(&stat, inode);
-
-	fhp->fh_pre_saved = true;
-}
-
-/*
- * Fill in the post_op attr for the wcc data
- */
-void fill_post_wcc(struct svc_fh *fhp)
-{
-	bool v4 = (fhp->fh_maxsize == NFS4_FHSIZE);
-	struct inode *inode = d_inode(fhp->fh_dentry);
-
-	if (fhp->fh_no_wcc)
-		return;
-
-	if (fhp->fh_post_saved)
-		printk("nfsd: inode locked twice during operation.\n");
-
-	fhp->fh_post_saved = true;
-
-	if (fs_supports_change_attribute(inode->i_sb) || !v4) {
-		__be32 err = fh_getattr(fhp, &fhp->fh_post_attr);
-
-		if (err) {
-			fhp->fh_post_saved = false;
-			fhp->fh_post_attr.ctime = inode->i_ctime;
-		}
-	}
-	if (v4)
-		fhp->fh_post_change =
-			nfsd4_change_attribute(&fhp->fh_post_attr, inode);
-}
-
 /*
  * XDR decode functions
  */
 
-int
-nfs3svc_decode_fhandleargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_fhandleargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_fhandle *args = rqstp->rq_argp;
 
 	return svcxdr_decode_nfs_fh3(xdr, &args->fh);
 }
 
-int
-nfs3svc_decode_sattrargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_sattrargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_sattrargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_nfs_fh3(xdr, &args->fh) &&
@@ -576,96 +509,81 @@
 		svcxdr_decode_sattrguard3(xdr, args);
 }
 
-int
-nfs3svc_decode_diropargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_diropargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_diropargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_diropargs3(xdr, &args->fh, &args->name, &args->len);
 }
 
-int
-nfs3svc_decode_accessargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_accessargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_accessargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->access) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nfs3svc_decode_readargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_readargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_readargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u64(xdr, &args->offset) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nfs3svc_decode_writeargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_writeargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_writeargs *args = rqstp->rq_argp;
 	u32 max_blocksize = svc_max_payload(rqstp);
-	struct kvec *head = rqstp->rq_arg.head;
-	struct kvec *tail = rqstp->rq_arg.tail;
-	size_t remaining;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u64(xdr, &args->offset) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->stable) < 0)
-		return 0;
+		return false;
 
 	/* opaque data */
 	if (xdr_stream_decode_u32(xdr, &args->len) < 0)
-		return 0;
+		return false;
 
 	/* request sanity */
 	if (args->count != args->len)
-		return 0;
-	remaining = head->iov_len + rqstp->rq_arg.page_len + tail->iov_len;
-	remaining -= xdr_stream_pos(xdr);
-	if (remaining < xdr_align_size(args->len))
-		return 0;
+		return false;
 	if (args->count > max_blocksize) {
 		args->count = max_blocksize;
 		args->len = max_blocksize;
 	}
 
-	args->first.iov_base = xdr->p;
-	args->first.iov_len = head->iov_len - xdr_stream_pos(xdr);
-
-	return 1;
+	return xdr_stream_subsegment(xdr, &args->payload, args->count);
 }
 
-int
-nfs3svc_decode_createargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_createargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_createargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_diropargs3(xdr, &args->fh, &args->name, &args->len))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->createmode) < 0)
-		return 0;
+		return false;
 	switch (args->createmode) {
 	case NFS3_CREATE_UNCHECKED:
 	case NFS3_CREATE_GUARDED:
@@ -673,18 +591,17 @@
 	case NFS3_CREATE_EXCLUSIVE:
 		args->verf = xdr_inline_decode(xdr, NFS3_CREATEVERFSIZE);
 		if (!args->verf)
-			return 0;
+			return false;
 		break;
 	default:
-		return 0;
+		return false;
 	}
-	return 1;
+	return true;
 }
 
-int
-nfs3svc_decode_mkdirargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_mkdirargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_createargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_diropargs3(xdr, &args->fh,
@@ -692,44 +609,34 @@
 		svcxdr_decode_sattr3(rqstp, xdr, &args->attrs);
 }
 
-int
-nfs3svc_decode_symlinkargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_symlinkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_symlinkargs *args = rqstp->rq_argp;
 	struct kvec *head = rqstp->rq_arg.head;
-	struct kvec *tail = rqstp->rq_arg.tail;
-	size_t remaining;
 
 	if (!svcxdr_decode_diropargs3(xdr, &args->ffh, &args->fname, &args->flen))
-		return 0;
+		return false;
 	if (!svcxdr_decode_sattr3(rqstp, xdr, &args->attrs))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->tlen) < 0)
-		return 0;
-
-	/* request sanity */
-	remaining = head->iov_len + rqstp->rq_arg.page_len + tail->iov_len;
-	remaining -= xdr_stream_pos(xdr);
-	if (remaining < xdr_align_size(args->tlen))
-		return 0;
+		return false;
 
-	args->first.iov_base = xdr->p;
+	/* symlink_data */
 	args->first.iov_len = head->iov_len - xdr_stream_pos(xdr);
-
-	return 1;
+	args->first.iov_base = xdr_inline_decode(xdr, args->tlen);
+	return args->first.iov_base != NULL;
 }
 
-int
-nfs3svc_decode_mknodargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_mknodargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_mknodargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_diropargs3(xdr, &args->fh, &args->name, &args->len))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->ftype) < 0)
-		return 0;
+		return false;
 	switch (args->ftype) {
 	case NF3CHR:
 	case NF3BLK:
@@ -743,16 +650,15 @@
 		/* Valid XDR but illegal file types */
 		break;
 	default:
-		return 0;
+		return false;
 	}
 
-	return 1;
+	return true;
 }
 
-int
-nfs3svc_decode_renameargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_renameargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_renameargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_diropargs3(xdr, &args->ffh,
@@ -761,10 +667,9 @@
 					 &args->tname, &args->tlen);
 }
 
-int
-nfs3svc_decode_linkargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_linkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_linkargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_nfs_fh3(xdr, &args->ffh) &&
@@ -772,62 +677,59 @@
 					 &args->tname, &args->tlen);
 }
 
-int
-nfs3svc_decode_readdirargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_readdirargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_readdirargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u64(xdr, &args->cookie) < 0)
-		return 0;
+		return false;
 	args->verf = xdr_inline_decode(xdr, NFS3_COOKIEVERFSIZE);
 	if (!args->verf)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nfs3svc_decode_readdirplusargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_readdirplusargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_readdirargs *args = rqstp->rq_argp;
 	u32 dircount;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u64(xdr, &args->cookie) < 0)
-		return 0;
+		return false;
 	args->verf = xdr_inline_decode(xdr, NFS3_COOKIEVERFSIZE);
 	if (!args->verf)
-		return 0;
+		return false;
 	/* dircount is ignored */
 	if (xdr_stream_decode_u32(xdr, &dircount) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nfs3svc_decode_commitargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_decode_commitargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd3_commitargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_nfs_fh3(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u64(xdr, &args->offset) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 /*
@@ -835,30 +737,28 @@
  */
 
 /* GETATTR */
-int
-nfs3svc_encode_getattrres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_getattrres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_attrstat *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		lease_get_mtime(d_inode(resp->fh.fh_dentry), &resp->stat.mtime);
 		if (!svcxdr_encode_fattr3(rqstp, xdr, &resp->fh, &resp->stat))
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
 /* SETATTR, REMOVE, RMDIR */
-int
-nfs3svc_encode_wccstat(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_wccstat(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_attrstat *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_nfsstat3(xdr, resp->status) &&
@@ -866,174 +766,168 @@
 }
 
 /* LOOKUP */
-int nfs3svc_encode_lookupres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_lookupres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_diropres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_nfs_fh3(xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->dirfh))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->dirfh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* ACCESS */
-int
-nfs3svc_encode_accessres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_accessres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_accessres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->access) < 0)
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* READLINK */
-int
-nfs3svc_encode_readlinkres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_readlinkres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_readlinkres *resp = rqstp->rq_resp;
 	struct kvec *head = rqstp->rq_res.head;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->len) < 0)
-			return 0;
+			return false;
 		xdr_write_pages(xdr, resp->pages, 0, resp->len);
 		if (svc_encode_result_payload(rqstp, head->iov_len, resp->len) < 0)
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* READ */
-int
-nfs3svc_encode_readres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_readres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_readres *resp = rqstp->rq_resp;
 	struct kvec *head = rqstp->rq_res.head;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->count) < 0)
-			return 0;
+			return false;
 		if (xdr_stream_encode_bool(xdr, resp->eof) < 0)
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->count) < 0)
-			return 0;
+			return false;
 		xdr_write_pages(xdr, resp->pages, rqstp->rq_res.page_base,
 				resp->count);
 		if (svc_encode_result_payload(rqstp, head->iov_len, resp->count) < 0)
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* WRITE */
-int
-nfs3svc_encode_writeres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_writeres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_writeres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_wcc_data(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->count) < 0)
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->committed) < 0)
-			return 0;
+			return false;
 		if (!svcxdr_encode_writeverf3(xdr, resp->verf))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_wcc_data(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* CREATE, MKDIR, SYMLINK, MKNOD */
-int
-nfs3svc_encode_createres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_createres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_diropres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_fh3(xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_wcc_data(rqstp, xdr, &resp->dirfh))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_wcc_data(rqstp, xdr, &resp->dirfh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* RENAME */
-int
-nfs3svc_encode_renameres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_renameres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_renameres *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_nfsstat3(xdr, resp->status) &&
@@ -1042,10 +936,9 @@
 }
 
 /* LINK */
-int
-nfs3svc_encode_linkres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_linkres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_linkres *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_nfsstat3(xdr, resp->status) &&
@@ -1054,34 +947,33 @@
 }
 
 /* READDIR */
-int
-nfs3svc_encode_readdirres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_readdirres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_readdirres *resp = rqstp->rq_resp;
 	struct xdr_buf *dirlist = &resp->dirlist;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_cookieverf3(xdr, resp->verf))
-			return 0;
+			return false;
 		xdr_write_pages(xdr, dirlist->pages, 0, dirlist->len);
 		/* no more entries */
 		if (xdr_stream_encode_item_absent(xdr) < 0)
-			return 0;
+			return false;
 		if (xdr_stream_encode_bool(xdr, resp->common.err == nfserr_eof) < 0)
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 static __be32
@@ -1158,7 +1050,7 @@
 		return false;
 	/* cookie */
 	resp->cookie_offset = dirlist->len;
-	if (xdr_stream_encode_u64(xdr, NFS_OFFSET_MAX) < 0)
+	if (xdr_stream_encode_u64(xdr, OFFSET_MAX) < 0)
 		return false;
 
 	return true;
@@ -1308,27 +1200,26 @@
 }
 
 /* FSSTAT */
-int
-nfs3svc_encode_fsstatres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_fsstatres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_fsstatres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &nfs3svc_null_fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_fsstat3resok(xdr, resp))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &nfs3svc_null_fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 static bool
@@ -1355,27 +1246,26 @@
 }
 
 /* FSINFO */
-int
-nfs3svc_encode_fsinfores(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_fsinfores(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_fsinfores *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &nfs3svc_null_fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_fsinfo3resok(xdr, resp))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &nfs3svc_null_fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 static bool
@@ -1398,51 +1288,49 @@
 }
 
 /* PATHCONF */
-int
-nfs3svc_encode_pathconfres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_pathconfres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_pathconfres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &nfs3svc_null_fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_pathconf3resok(xdr, resp))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_post_op_attr(rqstp, xdr, &nfs3svc_null_fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /* COMMIT */
-int
-nfs3svc_encode_commitres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs3svc_encode_commitres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd3_commitres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_nfsstat3(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_wcc_data(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_writeverf3(xdr, resp->verf))
-			return 0;
+			return false;
 		break;
 	default:
 		if (!svcxdr_encode_wcc_data(rqstp, xdr, &resp->fh))
-			return 0;
+			return false;
 	}
 
-	return 1;
+	return true;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4acl.c
@@ -751,58 +751,26 @@
 	return ret;
 }
 
-__be32
-nfsd4_set_nfs4_acl(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		struct nfs4_acl *acl)
+__be32 nfsd4_acl_to_attr(enum nfs_ftype4 type, struct nfs4_acl *acl,
+			 struct nfsd_attrs *attr)
 {
-	__be32 error;
 	int host_error;
-	struct dentry *dentry;
-	struct inode *inode;
-	struct posix_acl *pacl = NULL, *dpacl = NULL;
 	unsigned int flags = 0;
 
-	/* Get inode */
-	error = fh_verify(rqstp, fhp, 0, NFSD_MAY_SATTR);
-	if (error)
-		return error;
+	if (!acl)
+		return nfs_ok;
 
-	dentry = fhp->fh_dentry;
-	inode = d_inode(dentry);
-
-	if (S_ISDIR(inode->i_mode))
+	if (type == NF4DIR)
 		flags = NFS4_ACL_DIR;
 
-	host_error = nfs4_acl_nfsv4_to_posix(acl, &pacl, &dpacl, flags);
+	host_error = nfs4_acl_nfsv4_to_posix(acl, &attr->na_pacl,
+					     &attr->na_dpacl, flags);
 	if (host_error == -EINVAL)
 		return nfserr_attrnotsupp;
-	if (host_error < 0)
-		goto out_nfserr;
-
-	fh_lock(fhp);
-
-	host_error = set_posix_acl(&init_user_ns, inode, ACL_TYPE_ACCESS, pacl);
-	if (host_error < 0)
-		goto out_drop_lock;
-
-	if (S_ISDIR(inode->i_mode)) {
-		host_error = set_posix_acl(&init_user_ns, inode,
-					   ACL_TYPE_DEFAULT, dpacl);
-	}
-
-out_drop_lock:
-	fh_unlock(fhp);
-
-	posix_acl_release(pacl);
-	posix_acl_release(dpacl);
-out_nfserr:
-	if (host_error == -EOPNOTSUPP)
-		return nfserr_attrnotsupp;
 	else
 		return nfserrno(host_error);
 }
 
-
 static short
 ace2type(struct nfs4_ace *ace)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4callback.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4callback.c
@@ -76,6 +76,17 @@
  * 1 Protocol"
  */
 
+static void encode_uint32(struct xdr_stream *xdr, u32 n)
+{
+	WARN_ON_ONCE(xdr_stream_encode_u32(xdr, n) < 0);
+}
+
+static void encode_bitmap4(struct xdr_stream *xdr, const __u32 *bitmap,
+			   size_t len)
+{
+	WARN_ON_ONCE(xdr_stream_encode_uint32_array(xdr, bitmap, len) < 0);
+}
+
 /*
  *	nfs_cb_opnum4
  *
@@ -121,7 +132,7 @@
 
 	BUG_ON(length > NFS4_FHSIZE);
 	p = xdr_reserve_space(xdr, 4 + length);
-	xdr_encode_opaque(p, &fh->fh_base, length);
+	xdr_encode_opaque(p, &fh->fh_raw, length);
 }
 
 /*
@@ -286,17 +297,17 @@
 	u32 length;
 	__be32 *p;
 
-	p = xdr_inline_decode(xdr, 4 + 4);
+	p = xdr_inline_decode(xdr, XDR_UNIT);
 	if (unlikely(p == NULL))
 		goto out_overflow;
-	hdr->status = be32_to_cpup(p++);
+	hdr->status = be32_to_cpup(p);
 	/* Ignore the tag */
-	length = be32_to_cpup(p++);
-	p = xdr_inline_decode(xdr, length + 4);
-	if (unlikely(p == NULL))
+	if (xdr_stream_decode_u32(xdr, &length) < 0)
+		goto out_overflow;
+	if (xdr_inline_decode(xdr, length) == NULL)
+		goto out_overflow;
+	if (xdr_stream_decode_u32(xdr, &hdr->nops) < 0)
 		goto out_overflow;
-	p += XDR_QUADLEN(length);
-	hdr->nops = be32_to_cpup(p);
 	return 0;
 out_overflow:
 	return -EIO;
@@ -329,6 +340,24 @@
 }
 
 /*
+ * CB_RECALLANY4args
+ *
+ *	struct CB_RECALLANY4args {
+ *		uint32_t	craa_objects_to_keep;
+ *		bitmap4		craa_type_mask;
+ *	};
+ */
+static void
+encode_cb_recallany4args(struct xdr_stream *xdr,
+	struct nfs4_cb_compound_hdr *hdr, struct nfsd4_cb_recall_any *ra)
+{
+	encode_nfs_cb_opnum4(xdr, OP_CB_RECALL_ANY);
+	encode_uint32(xdr, ra->ra_keep);
+	encode_bitmap4(xdr, ra->ra_bmval, ARRAY_SIZE(ra->ra_bmval));
+	hdr->nops++;
+}
+
+/*
  * CB_SEQUENCE4args
  *
  *	struct CB_SEQUENCE4args {
@@ -482,6 +511,26 @@
 	encode_cb_nops(&hdr);
 }
 
+/*
+ * 20.6. Operation 8: CB_RECALL_ANY - Keep Any N Recallable Objects
+ */
+static void
+nfs4_xdr_enc_cb_recall_any(struct rpc_rqst *req,
+		struct xdr_stream *xdr, const void *data)
+{
+	const struct nfsd4_callback *cb = data;
+	struct nfsd4_cb_recall_any *ra;
+	struct nfs4_cb_compound_hdr hdr = {
+		.ident = cb->cb_clp->cl_cb_ident,
+		.minorversion = cb->cb_clp->cl_minorversion,
+	};
+
+	ra = container_of(cb, struct nfsd4_cb_recall_any, ra_cb);
+	encode_cb_compound4args(xdr, &hdr);
+	encode_cb_sequence4args(xdr, cb, &hdr);
+	encode_cb_recallany4args(xdr, &hdr, ra);
+	encode_cb_nops(&hdr);
+}
 
 /*
  * NFSv4.0 and NFSv4.1 XDR decode functions
@@ -520,6 +569,28 @@
 	return decode_cb_op_status(xdr, OP_CB_RECALL, &cb->cb_status);
 }
 
+/*
+ * 20.6. Operation 8: CB_RECALL_ANY - Keep Any N Recallable Objects
+ */
+static int
+nfs4_xdr_dec_cb_recall_any(struct rpc_rqst *rqstp,
+				  struct xdr_stream *xdr,
+				  void *data)
+{
+	struct nfsd4_callback *cb = data;
+	struct nfs4_cb_compound_hdr hdr;
+	int status;
+
+	status = decode_cb_compound4res(xdr, &hdr);
+	if (unlikely(status))
+		return status;
+	status = decode_cb_sequence4res(xdr, cb);
+	if (unlikely(status || cb->cb_seq_status))
+		return status;
+	status =  decode_cb_op_status(xdr, OP_CB_RECALL_ANY, &cb->cb_status);
+	return status;
+}
+
 #ifdef CONFIG_NFSD_PNFS
 /*
  * CB_LAYOUTRECALL4args
@@ -679,7 +750,7 @@
  *	case NFS4_OK:
  *		write_response4	coa_resok4;
  *	default:
- *	length4		coa_bytes_copied;
+ *		length4		coa_bytes_copied;
  * };
  * struct CB_OFFLOAD4args {
  *	nfs_fh4		coa_fh;
@@ -688,21 +759,22 @@
  * };
  */
 static void encode_offload_info4(struct xdr_stream *xdr,
-				 __be32 nfserr,
-				 const struct nfsd4_copy *cp)
+				 const struct nfsd4_cb_offload *cbo)
 {
 	__be32 *p;
 
 	p = xdr_reserve_space(xdr, 4);
-	*p++ = nfserr;
-	if (!nfserr) {
+	*p = cbo->co_nfserr;
+	switch (cbo->co_nfserr) {
+	case nfs_ok:
 		p = xdr_reserve_space(xdr, 4 + 8 + 4 + NFS4_VERIFIER_SIZE);
 		p = xdr_encode_empty_array(p);
-		p = xdr_encode_hyper(p, cp->cp_res.wr_bytes_written);
-		*p++ = cpu_to_be32(cp->cp_res.wr_stable_how);
-		p = xdr_encode_opaque_fixed(p, cp->cp_res.wr_verifier.data,
+		p = xdr_encode_hyper(p, cbo->co_res.wr_bytes_written);
+		*p++ = cpu_to_be32(cbo->co_res.wr_stable_how);
+		p = xdr_encode_opaque_fixed(p, cbo->co_res.wr_verifier.data,
 					    NFS4_VERIFIER_SIZE);
-	} else {
+		break;
+	default:
 		p = xdr_reserve_space(xdr, 8);
 		/* We always return success if bytes were written */
 		p = xdr_encode_hyper(p, 0);
@@ -710,18 +782,16 @@
 }
 
 static void encode_cb_offload4args(struct xdr_stream *xdr,
-				   __be32 nfserr,
-				   const struct knfsd_fh *fh,
-				   const struct nfsd4_copy *cp,
+				   const struct nfsd4_cb_offload *cbo,
 				   struct nfs4_cb_compound_hdr *hdr)
 {
 	__be32 *p;
 
 	p = xdr_reserve_space(xdr, 4);
-	*p++ = cpu_to_be32(OP_CB_OFFLOAD);
-	encode_nfs_fh4(xdr, fh);
-	encode_stateid4(xdr, &cp->cp_res.cb_stateid);
-	encode_offload_info4(xdr, nfserr, cp);
+	*p = cpu_to_be32(OP_CB_OFFLOAD);
+	encode_nfs_fh4(xdr, &cbo->co_fh);
+	encode_stateid4(xdr, &cbo->co_res.cb_stateid);
+	encode_offload_info4(xdr, cbo);
 
 	hdr->nops++;
 }
@@ -731,8 +801,8 @@
 				    const void *data)
 {
 	const struct nfsd4_callback *cb = data;
-	const struct nfsd4_copy *cp =
-		container_of(cb, struct nfsd4_copy, cp_cb);
+	const struct nfsd4_cb_offload *cbo =
+		container_of(cb, struct nfsd4_cb_offload, co_cb);
 	struct nfs4_cb_compound_hdr hdr = {
 		.ident = 0,
 		.minorversion = cb->cb_clp->cl_minorversion,
@@ -740,7 +810,7 @@
 
 	encode_cb_compound4args(xdr, &hdr);
 	encode_cb_sequence4args(xdr, cb, &hdr);
-	encode_cb_offload4args(xdr, cp->nfserr, &cp->fh, cp, &hdr);
+	encode_cb_offload4args(xdr, cbo, &hdr);
 	encode_cb_nops(&hdr);
 }
 
@@ -784,6 +854,7 @@
 #endif
 	PROC(CB_NOTIFY_LOCK,	COMPOUND,	cb_notify_lock,	cb_notify_lock),
 	PROC(CB_OFFLOAD,	COMPOUND,	cb_offload,	cb_offload),
+	PROC(CB_RECALL_ANY,	COMPOUND,	cb_recall_any,	cb_recall_any),
 };
 
 static unsigned int nfs4_cb_counts[ARRAY_SIZE(nfs4_cb_procedures)];
@@ -875,8 +946,8 @@
 		if (!kcred)
 			return NULL;
 
-		kcred->uid = ses->se_cb_sec.uid;
-		kcred->gid = ses->se_cb_sec.gid;
+		kcred->fsuid = ses->se_cb_sec.uid;
+		kcred->fsgid = ses->se_cb_sec.gid;
 		return kcred;
 	}
 }
@@ -915,9 +986,8 @@
 		args.authflavor = clp->cl_cred.cr_flavor;
 		clp->cl_cb_ident = conn->cb_ident;
 	} else {
-		if (!conn->cb_xprt)
+		if (!conn->cb_xprt || !ses)
 			return -EINVAL;
-		clp->cl_cb_conn.cb_xprt = conn->cb_xprt;
 		clp->cl_cb_session = ses;
 		args.bc_xprt = conn->cb_xprt;
 		args.prognumber = clp->cl_cb_session->se_cb_prog;
@@ -937,6 +1007,9 @@
 		rpc_shutdown_client(client);
 		return -ENOMEM;
 	}
+
+	if (clp->cl_minorversion != 0)
+		clp->cl_cb_conn.cb_xprt = conn->cb_xprt;
 	clp->cl_cb_client = client;
 	clp->cl_cb_cred = cred;
 	rcu_read_lock();
@@ -1129,6 +1202,7 @@
 		ret = false;
 		break;
 	case -NFS4ERR_DELAY:
+		cb->cb_seq_status = 1;
 		if (!rpc_restart_call(task))
 			goto out;
 
@@ -1336,8 +1410,11 @@
 		nfsd4_process_cb_update(cb);
 
 	clnt = clp->cl_cb_client;
-	if (!clnt) {
-		/* Callback channel broken, or client killed; give up: */
+	if (!clnt || clp->cl_state == NFSD4_COURTESY) {
+		/*
+		 * Callback channel broken, client killed or
+		 * nfs4_client in courtesy state; give up.
+		 */
 		nfsd41_destroy_cb(cb);
 		return;
 	}
@@ -1372,11 +1449,21 @@
 	cb->cb_holds_slot = false;
 }
 
-void nfsd4_run_cb(struct nfsd4_callback *cb)
+/**
+ * nfsd4_run_cb - queue up a callback job to run
+ * @cb: callback to queue
+ *
+ * Kick off a callback to do its thing. Returns false if it was already
+ * on a queue, true otherwise.
+ */
+bool nfsd4_run_cb(struct nfsd4_callback *cb)
 {
 	struct nfs4_client *clp = cb->cb_clp;
+	bool queued;
 
 	nfsd41_cb_inflight_begin(clp);
-	if (!nfsd4_queue_cb(cb))
+	queued = nfsd4_queue_cb(cb);
+	if (!queued)
 		nfsd41_cb_inflight_end(clp);
+	return queued;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4idmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4idmap.c
@@ -41,6 +41,7 @@
 #include "idmap.h"
 #include "nfsd.h"
 #include "netns.h"
+#include "vfs.h"
 
 /*
  * Turn off idmapping when using AUTH_SYS.
@@ -82,8 +83,8 @@
 	new->id = itm->id;
 	new->type = itm->type;
 
-	strlcpy(new->name, itm->name, sizeof(new->name));
-	strlcpy(new->authname, itm->authname, sizeof(new->authname));
+	strscpy(new->name, itm->name, sizeof(new->name));
+	strscpy(new->authname, itm->authname, sizeof(new->authname));
 }
 
 static void
@@ -548,7 +549,7 @@
 		return nfserr_badowner;
 	memcpy(key.name, name, namelen);
 	key.name[namelen] = '\0';
-	strlcpy(key.authname, rqst_authname(rqstp), sizeof(key.authname));
+	strscpy(key.authname, rqst_authname(rqstp), sizeof(key.authname));
 	ret = idmap_lookup(rqstp, nametoid_lookup, &key, nn->nametoid_cache, &item);
 	if (ret == -ENOENT)
 		return nfserr_badowner;
@@ -580,11 +581,12 @@
 		.id = id,
 		.type = type,
 	};
+	__be32 status = nfs_ok;
 	__be32 *p;
 	int ret;
 	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 
-	strlcpy(key.authname, rqst_authname(rqstp), sizeof(key.authname));
+	strscpy(key.authname, rqst_authname(rqstp), sizeof(key.authname));
 	ret = idmap_lookup(rqstp, idtoname_lookup, &key, nn->idtoname_cache, &item);
 	if (ret == -ENOENT)
 		return encode_ascii_id(xdr, id);
@@ -592,12 +594,16 @@
 		return nfserrno(ret);
 	ret = strlen(item->name);
 	WARN_ON_ONCE(ret > IDMAP_NAMESZ);
+
 	p = xdr_reserve_space(xdr, ret + 4);
-	if (!p)
-		return nfserr_resource;
-	p = xdr_encode_opaque(p, item->name, ret);
+	if (unlikely(!p)) {
+		status = nfserr_resource;
+		goto out_put;
+	}
+	xdr_encode_opaque(p, item->name, ret);
+out_put:
 	cache_put(&item->h, nn->idtoname_cache);
-	return 0;
+	return status;
 }
 
 static bool
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4layouts.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4layouts.c
@@ -322,11 +322,11 @@
 	if (ls->ls_recalled)
 		goto out_unlock;
 
-	ls->ls_recalled = true;
-	atomic_inc(&ls->ls_stid.sc_file->fi_lo_recalls);
 	if (list_empty(&ls->ls_layouts))
 		goto out_unlock;
 
+	ls->ls_recalled = true;
+	atomic_inc(&ls->ls_stid.sc_file->fi_lo_recalls);
 	trace_nfsd_layout_recall(&ls->ls_stid.sc_stateid);
 
 	refcount_inc(&ls->ls_stid.sc_count);
@@ -421,7 +421,7 @@
 	new = kmem_cache_alloc(nfs4_layout_cache, GFP_KERNEL);
 	if (!new)
 		return nfserr_jukebox;
-	memcpy(&new->lo_seg, seg, sizeof(lp->lo_seg));
+	memcpy(&new->lo_seg, seg, sizeof(new->lo_seg));
 	new->lo_state = ls;
 
 	spin_lock(&fp->fi_lock);
@@ -657,7 +657,7 @@
 	ktime_t now, cutoff;
 	const struct nfsd4_layout_ops *ops;
 
-
+	trace_nfsd_cb_layout_done(&ls->ls_stid.sc_stateid, task);
 	switch (task->tk_status) {
 	case 0:
 	case -NFS4ERR_DELAY:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4proc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4proc.c
@@ -37,6 +37,9 @@
 #include <linux/falloc.h>
 #include <linux/slab.h>
 #include <linux/kthread.h>
+#include <linux/namei.h>
+#include <linux/freezer.h>
+
 #include <linux/sunrpc/addr.h>
 #include <linux/nfs_ssc.h>
 
@@ -62,36 +65,6 @@
 		"idle msecs before unmount export from source server");
 #endif
 
-#ifdef CONFIG_NFSD_V4_SECURITY_LABEL
-#include <linux/security.h>
-
-static inline void
-nfsd4_security_inode_setsecctx(struct svc_fh *resfh, struct xdr_netobj *label, u32 *bmval)
-{
-	struct inode *inode = d_inode(resfh->fh_dentry);
-	int status;
-
-	inode_lock(inode);
-	status = security_inode_setsecctx(resfh->fh_dentry,
-		label->data, label->len);
-	inode_unlock(inode);
-
-	if (status)
-		/*
-		 * XXX: We should really fail the whole open, but we may
-		 * already have created a new file, so it may be too
-		 * late.  For now this seems the least of evils:
-		 */
-		bmval[2] &= ~FATTR4_WORD2_SECURITY_LABEL;
-
-	return;
-}
-#else
-static inline void
-nfsd4_security_inode_setsecctx(struct svc_fh *resfh, struct xdr_netobj *label, u32 *bmval)
-{ }
-#endif
-
 #define NFSDDBG_FACILITY		NFSDDBG_PROC
 
 static u32 nfsd_attrmask[] = {
@@ -156,26 +129,6 @@
 		    || open->op_createmode == NFS4_CREATE_EXCLUSIVE4_1);
 }
 
-/*
- * if error occurs when setting the acl, just clear the acl bit
- * in the returned attr bitmap.
- */
-static void
-do_set_nfs4_acl(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		struct nfs4_acl *acl, u32 *bmval)
-{
-	__be32 status;
-
-	status = nfsd4_set_nfs4_acl(rqstp, fhp, acl);
-	if (status)
-		/*
-		 * We should probably fail the whole open at this point,
-		 * but we've already created the file, so it's too late;
-		 * So this seems the least of evils:
-		 */
-		bmval[0] &= ~FATTR4_WORD0_ACL;
-}
-
 static inline void
 fh_dup2(struct svc_fh *dst, struct svc_fh *src)
 {
@@ -189,7 +142,6 @@
 static __be32
 do_open_permission(struct svc_rqst *rqstp, struct svc_fh *current_fh, struct nfsd4_open *open, int accmode)
 {
-	__be32 status;
 
 	if (open->op_truncate &&
 		!(open->op_share_access & NFS4_SHARE_ACCESS_WRITE))
@@ -204,9 +156,7 @@
 	if (open->op_share_deny & NFS4_SHARE_DENY_READ)
 		accmode |= NFSD_MAY_WRITE;
 
-	status = fh_verify(rqstp, current_fh, S_IFREG, accmode);
-
-	return status;
+	return fh_verify(rqstp, current_fh, S_IFREG, accmode);
 }
 
 static __be32 nfsd_check_obj_isreg(struct svc_fh *fh)
@@ -235,6 +185,202 @@
 			&resfh->fh_handle);
 }
 
+static inline bool nfsd4_create_is_exclusive(int createmode)
+{
+	return createmode == NFS4_CREATE_EXCLUSIVE ||
+		createmode == NFS4_CREATE_EXCLUSIVE4_1;
+}
+
+static __be32
+nfsd4_vfs_create(struct svc_fh *fhp, struct dentry *child,
+		 struct nfsd4_open *open)
+{
+	struct file *filp;
+	struct path path;
+	int oflags;
+
+	oflags = O_CREAT | O_LARGEFILE;
+	switch (open->op_share_access & NFS4_SHARE_ACCESS_BOTH) {
+	case NFS4_SHARE_ACCESS_WRITE:
+		oflags |= O_WRONLY;
+		break;
+	case NFS4_SHARE_ACCESS_BOTH:
+		oflags |= O_RDWR;
+		break;
+	default:
+		oflags |= O_RDONLY;
+	}
+
+	path.mnt = fhp->fh_export->ex_path.mnt;
+	path.dentry = child;
+	filp = dentry_create(&path, oflags, open->op_iattr.ia_mode,
+			     current_cred());
+	if (IS_ERR(filp))
+		return nfserrno(PTR_ERR(filp));
+
+	open->op_filp = filp;
+	return nfs_ok;
+}
+
+/*
+ * Implement NFSv4's unchecked, guarded, and exclusive create
+ * semantics for regular files. Open state for this new file is
+ * subsequently fabricated in nfsd4_process_open2().
+ *
+ * Upon return, caller must release @fhp and @resfhp.
+ */
+static __be32
+nfsd4_create_file(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		  struct svc_fh *resfhp, struct nfsd4_open *open)
+{
+	struct iattr *iap = &open->op_iattr;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= iap,
+		.na_seclabel	= &open->op_label,
+	};
+	struct dentry *parent, *child;
+	__u32 v_mtime, v_atime;
+	struct inode *inode;
+	__be32 status;
+	int host_err;
+
+	if (isdotent(open->op_fname, open->op_fnamelen))
+		return nfserr_exist;
+	if (!(iap->ia_valid & ATTR_MODE))
+		iap->ia_mode = 0;
+
+	status = fh_verify(rqstp, fhp, S_IFDIR, NFSD_MAY_EXEC);
+	if (status != nfs_ok)
+		return status;
+	parent = fhp->fh_dentry;
+	inode = d_inode(parent);
+
+	host_err = fh_want_write(fhp);
+	if (host_err)
+		return nfserrno(host_err);
+
+	if (is_create_with_attrs(open))
+		nfsd4_acl_to_attr(NF4REG, open->op_acl, &attrs);
+
+	inode_lock_nested(inode, I_MUTEX_PARENT);
+
+	child = lookup_one_len(open->op_fname, parent, open->op_fnamelen);
+	if (IS_ERR(child)) {
+		status = nfserrno(PTR_ERR(child));
+		goto out;
+	}
+
+	if (d_really_is_negative(child)) {
+		status = fh_verify(rqstp, fhp, S_IFDIR, NFSD_MAY_CREATE);
+		if (status != nfs_ok)
+			goto out;
+	}
+
+	status = fh_compose(resfhp, fhp->fh_export, child, fhp);
+	if (status != nfs_ok)
+		goto out;
+
+	v_mtime = 0;
+	v_atime = 0;
+	if (nfsd4_create_is_exclusive(open->op_createmode)) {
+		u32 *verifier = (u32 *)open->op_verf.data;
+
+		/*
+		 * Solaris 7 gets confused (bugid 4218508) if these have
+		 * the high bit set, as do xfs filesystems without the
+		 * "bigtime" feature. So just clear the high bits. If this
+		 * is ever changed to use different attrs for storing the
+		 * verifier, then do_open_lookup() will also need to be
+		 * fixed accordingly.
+		 */
+		v_mtime = verifier[0] & 0x7fffffff;
+		v_atime = verifier[1] & 0x7fffffff;
+	}
+
+	if (d_really_is_positive(child)) {
+		status = nfs_ok;
+
+		/* NFSv4 protocol requires change attributes even though
+		 * no change happened.
+		 */
+		fh_fill_both_attrs(fhp);
+
+		switch (open->op_createmode) {
+		case NFS4_CREATE_UNCHECKED:
+			if (!d_is_reg(child))
+				break;
+
+			/*
+			 * In NFSv4, we don't want to truncate the file
+			 * now. This would be wrong if the OPEN fails for
+			 * some other reason. Furthermore, if the size is
+			 * nonzero, we should ignore it according to spec!
+			 */
+			open->op_truncate = (iap->ia_valid & ATTR_SIZE) &&
+						!iap->ia_size;
+			break;
+		case NFS4_CREATE_GUARDED:
+			status = nfserr_exist;
+			break;
+		case NFS4_CREATE_EXCLUSIVE:
+			if (d_inode(child)->i_mtime.tv_sec == v_mtime &&
+			    d_inode(child)->i_atime.tv_sec == v_atime &&
+			    d_inode(child)->i_size == 0) {
+				open->op_created = true;
+				break;		/* subtle */
+			}
+			status = nfserr_exist;
+			break;
+		case NFS4_CREATE_EXCLUSIVE4_1:
+			if (d_inode(child)->i_mtime.tv_sec == v_mtime &&
+			    d_inode(child)->i_atime.tv_sec == v_atime &&
+			    d_inode(child)->i_size == 0) {
+				open->op_created = true;
+				goto set_attr;	/* subtle */
+			}
+			status = nfserr_exist;
+		}
+		goto out;
+	}
+
+	if (!IS_POSIXACL(inode))
+		iap->ia_mode &= ~current_umask();
+
+	fh_fill_pre_attrs(fhp);
+	status = nfsd4_vfs_create(fhp, child, open);
+	if (status != nfs_ok)
+		goto out;
+	open->op_created = true;
+	fh_fill_post_attrs(fhp);
+
+	/* A newly created file already has a file size of zero. */
+	if ((iap->ia_valid & ATTR_SIZE) && (iap->ia_size == 0))
+		iap->ia_valid &= ~ATTR_SIZE;
+	if (nfsd4_create_is_exclusive(open->op_createmode)) {
+		iap->ia_valid = ATTR_MTIME | ATTR_ATIME |
+				ATTR_MTIME_SET|ATTR_ATIME_SET;
+		iap->ia_mtime.tv_sec = v_mtime;
+		iap->ia_atime.tv_sec = v_atime;
+		iap->ia_mtime.tv_nsec = 0;
+		iap->ia_atime.tv_nsec = 0;
+	}
+
+set_attr:
+	status = nfsd_create_setattr(rqstp, fhp, resfhp, &attrs);
+
+	if (attrs.na_labelerr)
+		open->op_bmval[2] &= ~FATTR4_WORD2_SECURITY_LABEL;
+	if (attrs.na_aclerr)
+		open->op_bmval[0] &= ~FATTR4_WORD0_ACL;
+out:
+	inode_unlock(inode);
+	nfsd_attrs_free(&attrs);
+	if (child && !IS_ERR(child))
+		dput(child);
+	fh_drop_write(fhp);
+	return status;
+}
+
 static __be32
 do_open_lookup(struct svc_rqst *rqstp, struct nfsd4_compound_state *cstate, struct nfsd4_open *open, struct svc_fh **resfh)
 {
@@ -264,47 +410,33 @@
 		 * yes          | yes    | GUARDED4        | GUARDED4
 		 */
 
-		/*
-		 * Note: create modes (UNCHECKED,GUARDED...) are the same
-		 * in NFSv4 as in v3 except EXCLUSIVE4_1.
-		 */
 		current->fs->umask = open->op_umask;
-		status = do_nfsd_create(rqstp, current_fh, open->op_fname,
-					open->op_fnamelen, &open->op_iattr,
-					*resfh, open->op_createmode,
-					(u32 *)open->op_verf.data,
-					&open->op_truncate, &open->op_created);
+		status = nfsd4_create_file(rqstp, current_fh, *resfh, open);
 		current->fs->umask = 0;
 
-		if (!status && open->op_label.len)
-			nfsd4_security_inode_setsecctx(*resfh, &open->op_label, open->op_bmval);
-
 		/*
 		 * Following rfc 3530 14.2.16, and rfc 5661 18.16.4
 		 * use the returned bitmask to indicate which attributes
 		 * we used to store the verifier:
 		 */
-		if (nfsd_create_is_exclusive(open->op_createmode) && status == 0)
+		if (nfsd4_create_is_exclusive(open->op_createmode) && status == 0)
 			open->op_bmval[1] |= (FATTR4_WORD1_TIME_ACCESS |
 						FATTR4_WORD1_TIME_MODIFY);
-	} else
-		/*
-		 * Note this may exit with the parent still locked.
-		 * We will hold the lock until nfsd4_open's final
-		 * lookup, to prevent renames or unlinks until we've had
-		 * a chance to an acquire a delegation if appropriate.
-		 */
+	} else {
 		status = nfsd_lookup(rqstp, current_fh,
 				     open->op_fname, open->op_fnamelen, *resfh);
+		if (!status)
+			/* NFSv4 protocol requires change attributes even though
+			 * no change happened.
+			 */
+			fh_fill_both_attrs(current_fh);
+	}
 	if (status)
 		goto out;
 	status = nfsd_check_obj_isreg(*resfh);
 	if (status)
 		goto out;
 
-	if (is_create_with_attrs(open) && open->op_acl != NULL)
-		do_set_nfs4_acl(rqstp, *resfh, open->op_acl, open->op_bmval);
-
 	nfsd4_set_open_owner_reply_cache(cstate, open, *resfh);
 	accmode = NFSD_MAY_NOP;
 	if (open->op_created ||
@@ -320,7 +452,6 @@
 do_open_fhandle(struct svc_rqst *rqstp, struct nfsd4_compound_state *cstate, struct nfsd4_open *open)
 {
 	struct svc_fh *current_fh = &cstate->current_fh;
-	__be32 status;
 	int accmode = 0;
 
 	/* We don't know the target directory, and therefore can not
@@ -345,9 +476,7 @@
 	if (open->op_claim_type == NFS4_OPEN_CLAIM_DELEG_CUR_FH)
 		accmode = NFSD_MAY_OWNER_OVERRIDE;
 
-	status = do_open_permission(rqstp, current_fh, open, accmode);
-
-	return status;
+	return do_open_permission(rqstp, current_fh, open, accmode);
 }
 
 static void
@@ -375,6 +504,9 @@
 		(int)open->op_fnamelen, open->op_fname,
 		open->op_openowner);
 
+	open->op_filp = NULL;
+	open->op_rqstp = rqstp;
+
 	/* This check required by spec. */
 	if (open->op_create && open->op_claim_type != NFS4_OPEN_CLAIM_NULL)
 		return nfserr_inval;
@@ -427,50 +559,46 @@
 		goto out;
 
 	switch (open->op_claim_type) {
-		case NFS4_OPEN_CLAIM_DELEGATE_CUR:
-		case NFS4_OPEN_CLAIM_NULL:
-			status = do_open_lookup(rqstp, cstate, open, &resfh);
-			if (status)
-				goto out;
-			break;
-		case NFS4_OPEN_CLAIM_PREVIOUS:
-			status = nfs4_check_open_reclaim(cstate->clp);
-			if (status)
-				goto out;
-			open->op_openowner->oo_flags |= NFS4_OO_CONFIRMED;
-			reclaim = true;
-			fallthrough;
-		case NFS4_OPEN_CLAIM_FH:
-		case NFS4_OPEN_CLAIM_DELEG_CUR_FH:
-			status = do_open_fhandle(rqstp, cstate, open);
-			if (status)
-				goto out;
-			resfh = &cstate->current_fh;
-			break;
-		case NFS4_OPEN_CLAIM_DELEG_PREV_FH:
-             	case NFS4_OPEN_CLAIM_DELEGATE_PREV:
-			dprintk("NFSD: unsupported OPEN claim type %d\n",
-				open->op_claim_type);
-			status = nfserr_notsupp;
+	case NFS4_OPEN_CLAIM_DELEGATE_CUR:
+	case NFS4_OPEN_CLAIM_NULL:
+		status = do_open_lookup(rqstp, cstate, open, &resfh);
+		if (status)
 			goto out;
-		default:
-			dprintk("NFSD: Invalid OPEN claim type %d\n",
-				open->op_claim_type);
-			status = nfserr_inval;
+		break;
+	case NFS4_OPEN_CLAIM_PREVIOUS:
+		status = nfs4_check_open_reclaim(cstate->clp);
+		if (status)
 			goto out;
+		open->op_openowner->oo_flags |= NFS4_OO_CONFIRMED;
+		reclaim = true;
+		fallthrough;
+	case NFS4_OPEN_CLAIM_FH:
+	case NFS4_OPEN_CLAIM_DELEG_CUR_FH:
+		status = do_open_fhandle(rqstp, cstate, open);
+		if (status)
+			goto out;
+		resfh = &cstate->current_fh;
+		break;
+	case NFS4_OPEN_CLAIM_DELEG_PREV_FH:
+	case NFS4_OPEN_CLAIM_DELEGATE_PREV:
+		status = nfserr_notsupp;
+		goto out;
+	default:
+		status = nfserr_inval;
+		goto out;
 	}
-	/*
-	 * nfsd4_process_open2() does the actual opening of the file.  If
-	 * successful, it (1) truncates the file if open->op_truncate was
-	 * set, (2) sets open->op_stateid, (3) sets open->op_delegation.
-	 */
+
 	status = nfsd4_process_open2(rqstp, resfh, open);
-	WARN(status && open->op_created,
-	     "nfsd4_process_open2 failed to open newly-created file! status=%u\n",
-	     be32_to_cpu(status));
+	if (status && open->op_created)
+		pr_warn("nfsd4_process_open2 failed to open newly-created file: status=%u\n",
+			be32_to_cpu(status));
 	if (reclaim && !status)
 		nn->somebody_reclaimed = true;
 out:
+	if (open->op_filp) {
+		fput(open->op_filp);
+		open->op_filp = NULL;
+	}
 	if (resfh && resfh != &cstate->current_fh) {
 		fh_dup2(&cstate->current_fh, resfh);
 		fh_put(resfh);
@@ -519,7 +647,7 @@
 
 	fh_put(&cstate->current_fh);
 	cstate->current_fh.fh_handle.fh_size = putfh->pf_fhlen;
-	memcpy(&cstate->current_fh.fh_handle.fh_base, putfh->pf_fhval,
+	memcpy(&cstate->current_fh.fh_handle.fh_raw, putfh->pf_fhval,
 	       putfh->pf_fhlen);
 	ret = fh_verify(rqstp, &cstate->current_fh, 0, NFSD_MAY_BYPASS_GSS);
 #ifdef CONFIG_NFSD_V4_2_INTER_SSC
@@ -535,11 +663,9 @@
 nfsd4_putrootfh(struct svc_rqst *rqstp, struct nfsd4_compound_state *cstate,
 		union nfsd4_op_u *u)
 {
-	__be32 status;
-
 	fh_put(&cstate->current_fh);
-	status = exp_pseudoroot(rqstp, &cstate->current_fh);
-	return status;
+
+	return exp_pseudoroot(rqstp, &cstate->current_fh);
 }
 
 static __be32
@@ -592,24 +718,24 @@
 			   &access->ac_supported);
 }
 
-static void gen_boot_verifier(nfs4_verifier *verifier, struct net *net)
-{
-	__be32 *verf = (__be32 *)verifier->data;
-
-	BUILD_BUG_ON(2*sizeof(*verf) != sizeof(verifier->data));
-
-	nfsd_copy_boot_verifier(verf, net_generic(net, nfsd_net_id));
-}
-
 static __be32
 nfsd4_commit(struct svc_rqst *rqstp, struct nfsd4_compound_state *cstate,
 	     union nfsd4_op_u *u)
 {
 	struct nfsd4_commit *commit = &u->commit;
+	struct nfsd_file *nf;
+	__be32 status;
+
+	status = nfsd_file_acquire(rqstp, &cstate->current_fh, NFSD_MAY_WRITE |
+				   NFSD_MAY_NOT_BREAK_LEASE, &nf);
+	if (status != nfs_ok)
+		return status;
 
-	return nfsd_commit(rqstp, &cstate->current_fh, commit->co_offset,
+	status = nfsd_commit(rqstp, &cstate->current_fh, nf, commit->co_offset,
 			     commit->co_count,
 			     (__be32 *)commit->co_verf.data);
+	nfsd_file_put(nf);
+	return status;
 }
 
 static __be32
@@ -617,6 +743,10 @@
 	     union nfsd4_op_u *u)
 {
 	struct nfsd4_create *create = &u->create;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &create->cr_iattr,
+		.na_seclabel	= &create->cr_label,
+	};
 	struct svc_fh resfh;
 	__be32 status;
 	dev_t rdev;
@@ -632,12 +762,13 @@
 	if (status)
 		return status;
 
+	status = nfsd4_acl_to_attr(create->cr_type, create->cr_acl, &attrs);
 	current->fs->umask = create->cr_umask;
 	switch (create->cr_type) {
 	case NF4LNK:
 		status = nfsd_symlink(rqstp, &cstate->current_fh,
 				      create->cr_name, create->cr_namelen,
-				      create->cr_data, &resfh);
+				      create->cr_data, &attrs, &resfh);
 		break;
 
 	case NF4BLK:
@@ -648,7 +779,7 @@
 			goto out_umask;
 		status = nfsd_create(rqstp, &cstate->current_fh,
 				     create->cr_name, create->cr_namelen,
-				     &create->cr_iattr, S_IFBLK, rdev, &resfh);
+				     &attrs, S_IFBLK, rdev, &resfh);
 		break;
 
 	case NF4CHR:
@@ -659,26 +790,26 @@
 			goto out_umask;
 		status = nfsd_create(rqstp, &cstate->current_fh,
 				     create->cr_name, create->cr_namelen,
-				     &create->cr_iattr,S_IFCHR, rdev, &resfh);
+				     &attrs, S_IFCHR, rdev, &resfh);
 		break;
 
 	case NF4SOCK:
 		status = nfsd_create(rqstp, &cstate->current_fh,
 				     create->cr_name, create->cr_namelen,
-				     &create->cr_iattr, S_IFSOCK, 0, &resfh);
+				     &attrs, S_IFSOCK, 0, &resfh);
 		break;
 
 	case NF4FIFO:
 		status = nfsd_create(rqstp, &cstate->current_fh,
 				     create->cr_name, create->cr_namelen,
-				     &create->cr_iattr, S_IFIFO, 0, &resfh);
+				     &attrs, S_IFIFO, 0, &resfh);
 		break;
 
 	case NF4DIR:
 		create->cr_iattr.ia_valid &= ~ATTR_SIZE;
 		status = nfsd_create(rqstp, &cstate->current_fh,
 				     create->cr_name, create->cr_namelen,
-				     &create->cr_iattr, S_IFDIR, 0, &resfh);
+				     &attrs, S_IFDIR, 0, &resfh);
 		break;
 
 	default:
@@ -688,20 +819,17 @@
 	if (status)
 		goto out;
 
-	if (create->cr_label.len)
-		nfsd4_security_inode_setsecctx(&resfh, &create->cr_label, create->cr_bmval);
-
-	if (create->cr_acl != NULL)
-		do_set_nfs4_acl(rqstp, &resfh, create->cr_acl,
-				create->cr_bmval);
-
-	fh_unlock(&cstate->current_fh);
+	if (attrs.na_labelerr)
+		create->cr_bmval[2] &= ~FATTR4_WORD2_SECURITY_LABEL;
+	if (attrs.na_aclerr)
+		create->cr_bmval[0] &= ~FATTR4_WORD0_ACL;
 	set_change_info(&create->cr_cinfo, &cstate->current_fh);
 	fh_dup2(&cstate->current_fh, &resfh);
 out:
 	fh_put(&resfh);
 out_umask:
 	current->fs->umask = 0;
+	nfsd_attrs_free(&attrs);
 	return status;
 }
 
@@ -782,12 +910,16 @@
 	__be32 status;
 
 	read->rd_nf = NULL;
-	if (read->rd_offset >= OFFSET_MAX)
-		return nfserr_inval;
 
 	trace_nfsd_read_start(rqstp, &cstate->current_fh,
 			      read->rd_offset, read->rd_length);
 
+	read->rd_length = min_t(u32, read->rd_length, svc_max_payload(rqstp));
+	if (read->rd_offset > (u64)OFFSET_MAX)
+		read->rd_offset = (u64)OFFSET_MAX;
+	if (read->rd_offset + read->rd_length > (u64)OFFSET_MAX)
+		read->rd_length = (u64)OFFSET_MAX - read->rd_offset;
+
 	/*
 	 * If we do a zero copy read, then a client will see read data
 	 * that reflects the state of the file *after* performing the
@@ -803,12 +935,7 @@
 	status = nfs4_preprocess_stateid_op(rqstp, cstate, &cstate->current_fh,
 					&read->rd_stateid, RD_STATE,
 					&read->rd_nf, NULL);
-	if (status) {
-		dprintk("NFSD: nfsd4_read: couldn't process stateid!\n");
-		goto out;
-	}
-	status = nfs_ok;
-out:
+
 	read->rd_rqstp = rqstp;
 	read->rd_fhp = &cstate->current_fh;
 	return status;
@@ -870,10 +997,8 @@
 		return nfserr_grace;
 	status = nfsd_unlink(rqstp, &cstate->current_fh, 0,
 			     remove->rm_name, remove->rm_namelen);
-	if (!status) {
-		fh_unlock(&cstate->current_fh);
+	if (!status)
 		set_change_info(&remove->rm_cinfo, &cstate->current_fh);
-	}
 	return status;
 }
 
@@ -891,8 +1016,8 @@
 			     rename->rn_tname, rename->rn_tnamelen);
 	if (status)
 		return status;
-	set_change_info(&rename->rn_sinfo, &cstate->current_fh);
-	set_change_info(&rename->rn_tinfo, &cstate->save_fh);
+	set_change_info(&rename->rn_sinfo, &cstate->save_fh);
+	set_change_info(&rename->rn_tinfo, &cstate->current_fh);
 	return nfs_ok;
 }
 
@@ -913,7 +1038,6 @@
 				    &exp, &dentry);
 	if (err)
 		return err;
-	fh_unlock(&cstate->current_fh);
 	if (d_really_is_negative(dentry)) {
 		exp_put(exp);
 		err = nfserr_noent;
@@ -968,17 +1092,21 @@
 	      union nfsd4_op_u *u)
 {
 	struct nfsd4_setattr *setattr = &u->setattr;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &setattr->sa_iattr,
+		.na_seclabel	= &setattr->sa_label,
+	};
+	struct inode *inode;
 	__be32 status = nfs_ok;
+	bool save_no_wcc;
 	int err;
 
 	if (setattr->sa_iattr.ia_valid & ATTR_SIZE) {
 		status = nfs4_preprocess_stateid_op(rqstp, cstate,
 				&cstate->current_fh, &setattr->sa_stateid,
 				WR_STATE, NULL, NULL);
-		if (status) {
-			dprintk("NFSD: nfsd4_setattr: couldn't process stateid!\n");
+		if (status)
 			return status;
-		}
 	}
 	err = fh_want_write(&cstate->current_fh);
 	if (err)
@@ -990,19 +1118,23 @@
 	if (status)
 		goto out;
 
-	if (setattr->sa_acl != NULL)
-		status = nfsd4_set_nfs4_acl(rqstp, &cstate->current_fh,
-					    setattr->sa_acl);
-	if (status)
-		goto out;
-	if (setattr->sa_label.len)
-		status = nfsd4_set_nfs4_label(rqstp, &cstate->current_fh,
-				&setattr->sa_label);
+	inode = cstate->current_fh.fh_dentry->d_inode;
+	status = nfsd4_acl_to_attr(S_ISDIR(inode->i_mode) ? NF4DIR : NF4REG,
+				   setattr->sa_acl, &attrs);
+
 	if (status)
 		goto out;
-	status = nfsd_setattr(rqstp, &cstate->current_fh, &setattr->sa_iattr,
+	save_no_wcc = cstate->current_fh.fh_no_wcc;
+	cstate->current_fh.fh_no_wcc = true;
+	status = nfsd_setattr(rqstp, &cstate->current_fh, &attrs,
 				0, (time64_t)0);
+	cstate->current_fh.fh_no_wcc = save_no_wcc;
+	if (!status)
+		status = nfserrno(attrs.na_labelerr);
+	if (!status)
+		status = nfserrno(attrs.na_aclerr);
 out:
+	nfsd_attrs_free(&attrs);
 	fh_drop_write(&cstate->current_fh);
 	return status;
 }
@@ -1018,23 +1150,21 @@
 	unsigned long cnt;
 	int nvecs;
 
-	if (write->wr_offset >= OFFSET_MAX)
-		return nfserr_inval;
+	if (write->wr_offset > (u64)OFFSET_MAX ||
+	    write->wr_offset + write->wr_buflen > (u64)OFFSET_MAX)
+		return nfserr_fbig;
 
 	cnt = write->wr_buflen;
 	trace_nfsd_write_start(rqstp, &cstate->current_fh,
 			       write->wr_offset, cnt);
 	status = nfs4_preprocess_stateid_op(rqstp, cstate, &cstate->current_fh,
 						stateid, WR_STATE, &nf, NULL);
-	if (status) {
-		dprintk("NFSD: nfsd4_write: couldn't process stateid!\n");
+	if (status)
 		return status;
-	}
 
 	write->wr_how_written = write->wr_stable_how;
 
-	nvecs = svc_fill_write_vector(rqstp, write->wr_payload.pages,
-				      write->wr_payload.head, write->wr_buflen);
+	nvecs = svc_fill_write_vector(rqstp, &write->wr_payload);
 	WARN_ON_ONCE(nvecs > ARRAY_SIZE(rqstp->rq_vec));
 
 	status = nfsd_vfs_write(rqstp, &cstate->current_fh, nf,
@@ -1061,17 +1191,13 @@
 
 	status = nfs4_preprocess_stateid_op(rqstp, cstate, &cstate->save_fh,
 					    src_stateid, RD_STATE, src, NULL);
-	if (status) {
-		dprintk("NFSD: %s: couldn't process src stateid!\n", __func__);
+	if (status)
 		goto out;
-	}
 
 	status = nfs4_preprocess_stateid_op(rqstp, cstate, &cstate->current_fh,
 					    dst_stateid, WR_STATE, dst, NULL);
-	if (status) {
-		dprintk("NFSD: %s: couldn't process dst stateid!\n", __func__);
+	if (status)
 		goto out_put_src;
-	}
 
 	/* fix up for NFS-specific error code */
 	if (!S_ISREG(file_inode((*src)->nf_file)->i_mode) ||
@@ -1084,8 +1210,10 @@
 	return status;
 out_put_dst:
 	nfsd_file_put(*dst);
+	*dst = NULL;
 out_put_src:
 	nfsd_file_put(*src);
+	*src = NULL;
 	goto out;
 }
 
@@ -1102,7 +1230,7 @@
 	if (status)
 		goto out;
 
-	status = nfsd4_clone_file_range(src, clone->cl_src_pos,
+	status = nfsd4_clone_file_range(rqstp, src, clone->cl_src_pos,
 			dst, clone->cl_dst_pos, clone->cl_count,
 			EX_ISSYNC(cstate->current_fh.fh_export));
 
@@ -1112,35 +1240,23 @@
 	return status;
 }
 
-void nfs4_put_copy(struct nfsd4_copy *copy)
+static void nfs4_put_copy(struct nfsd4_copy *copy)
 {
 	if (!refcount_dec_and_test(&copy->refcount))
 		return;
+	atomic_dec(&copy->cp_nn->pending_async_copies);
+	kfree(copy->cp_src);
 	kfree(copy);
 }
 
-static bool
-check_and_set_stop_copy(struct nfsd4_copy *copy)
-{
-	bool value;
-
-	spin_lock(&copy->cp_clp->async_lock);
-	value = copy->stopped;
-	if (!copy->stopped)
-		copy->stopped = true;
-	spin_unlock(&copy->cp_clp->async_lock);
-	return value;
-}
-
 static void nfsd4_stop_copy(struct nfsd4_copy *copy)
 {
-	/* only 1 thread should stop the copy */
-	if (!check_and_set_stop_copy(copy))
+	if (!test_and_set_bit(NFSD4_COPY_F_STOPPED, &copy->cp_flags))
 		kthread_stop(copy->copy_task);
 	nfs4_put_copy(copy);
 }
 
-static struct nfsd4_copy *nfsd4_get_copy(struct nfs4_client *clp)
+static struct nfsd4_copy *nfsd4_unhash_copy(struct nfs4_client *clp)
 {
 	struct nfsd4_copy *copy = NULL;
 
@@ -1149,6 +1265,9 @@
 		copy = list_first_entry(&clp->async_copies, struct nfsd4_copy,
 					copies);
 		refcount_inc(&copy->refcount);
+		copy->cp_clp = NULL;
+		if (!list_empty(&copy->copies))
+			list_del_init(&copy->copies);
 	}
 	spin_unlock(&clp->async_lock);
 	return copy;
@@ -1158,7 +1277,7 @@
 {
 	struct nfsd4_copy *copy;
 
-	while ((copy = nfsd4_get_copy(clp)) != NULL)
+	while ((copy = nfsd4_unhash_copy(clp)) != NULL)
 		nfsd4_stop_copy(copy);
 }
 #ifdef CONFIG_NFSD_V4_2_INTER_SSC
@@ -1176,15 +1295,15 @@
  * setup a work entry in the ssc delayed unmount list.
  */
 static __be32 nfsd4_ssc_setup_dul(struct nfsd_net *nn, char *ipaddr,
-		struct nfsd4_ssc_umount_item **retwork, struct vfsmount **ss_mnt)
+				  struct nfsd4_ssc_umount_item **nsui)
 {
-	struct nfsd4_ssc_umount_item *ni = 0;
+	struct nfsd4_ssc_umount_item *ni = NULL;
 	struct nfsd4_ssc_umount_item *work = NULL;
 	struct nfsd4_ssc_umount_item *tmp;
 	DEFINE_WAIT(wait);
+	__be32 status = 0;
 
-	*ss_mnt = NULL;
-	*retwork = NULL;
+	*nsui = NULL;
 	work = kzalloc(sizeof(*work), GFP_KERNEL);
 try_again:
 	spin_lock(&nn->nfsd_ssc_lock);
@@ -1194,57 +1313,58 @@
 		/* found a match */
 		if (ni->nsui_busy) {
 			/*  wait - and try again */
-			prepare_to_wait(&nn->nfsd_ssc_waitq, &wait,
-				TASK_INTERRUPTIBLE);
+			prepare_to_wait(&nn->nfsd_ssc_waitq, &wait, TASK_IDLE);
 			spin_unlock(&nn->nfsd_ssc_lock);
 
 			/* allow 20secs for mount/unmount for now - revisit */
-			if (signal_pending(current) ||
-					(schedule_timeout(20*HZ) == 0)) {
+			if (kthread_should_stop() ||
+					(freezable_schedule_timeout(20*HZ) == 0)) {
+				finish_wait(&nn->nfsd_ssc_waitq, &wait);
 				kfree(work);
 				return nfserr_eagain;
 			}
 			finish_wait(&nn->nfsd_ssc_waitq, &wait);
 			goto try_again;
 		}
-		*ss_mnt = ni->nsui_vfsmount;
+		*nsui = ni;
 		refcount_inc(&ni->nsui_refcnt);
 		spin_unlock(&nn->nfsd_ssc_lock);
 		kfree(work);
 
-		/* return vfsmount in ss_mnt */
+		/* return vfsmount in (*nsui)->nsui_vfsmount */
 		return 0;
 	}
 	if (work) {
-		strncpy(work->nsui_ipaddr, ipaddr, sizeof(work->nsui_ipaddr));
+		strscpy(work->nsui_ipaddr, ipaddr, sizeof(work->nsui_ipaddr) - 1);
 		refcount_set(&work->nsui_refcnt, 2);
 		work->nsui_busy = true;
 		list_add_tail(&work->nsui_list, &nn->nfsd_ssc_mount_list);
-		*retwork = work;
-	}
+		*nsui = work;
+	} else
+		status = nfserr_resource;
 	spin_unlock(&nn->nfsd_ssc_lock);
-	return 0;
+	return status;
 }
 
-static void nfsd4_ssc_update_dul_work(struct nfsd_net *nn,
-		struct nfsd4_ssc_umount_item *work, struct vfsmount *ss_mnt)
+static void nfsd4_ssc_update_dul(struct nfsd_net *nn,
+				 struct nfsd4_ssc_umount_item *nsui,
+				 struct vfsmount *ss_mnt)
 {
-	/* set nsui_vfsmount, clear busy flag and wakeup waiters */
 	spin_lock(&nn->nfsd_ssc_lock);
-	work->nsui_vfsmount = ss_mnt;
-	work->nsui_busy = false;
+	nsui->nsui_vfsmount = ss_mnt;
+	nsui->nsui_busy = false;
 	wake_up_all(&nn->nfsd_ssc_waitq);
 	spin_unlock(&nn->nfsd_ssc_lock);
 }
 
-static void nfsd4_ssc_cancel_dul_work(struct nfsd_net *nn,
-		struct nfsd4_ssc_umount_item *work)
+static void nfsd4_ssc_cancel_dul(struct nfsd_net *nn,
+				 struct nfsd4_ssc_umount_item *nsui)
 {
 	spin_lock(&nn->nfsd_ssc_lock);
-	list_del(&work->nsui_list);
+	list_del(&nsui->nsui_list);
 	wake_up_all(&nn->nfsd_ssc_waitq);
 	spin_unlock(&nn->nfsd_ssc_lock);
-	kfree(work);
+	kfree(nsui);
 }
 
 /*
@@ -1252,7 +1372,7 @@
  */
 static __be32
 nfsd4_interssc_connect(struct nl4_server *nss, struct svc_rqst *rqstp,
-		       struct vfsmount **mount)
+		       struct nfsd4_ssc_umount_item **nsui)
 {
 	struct file_system_type *type;
 	struct vfsmount *ss_mnt;
@@ -1263,7 +1383,6 @@
 	char *ipaddr, *dev_name, *raw_data;
 	int len, raw_len;
 	__be32 status = nfserr_inval;
-	struct nfsd4_ssc_umount_item *work = NULL;
 	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 
 	naddr = &nss->u.nl4_addr;
@@ -1271,6 +1390,7 @@
 					 naddr->addr_len,
 					 (struct sockaddr *)&tmp_addr,
 					 sizeof(tmp_addr));
+	*nsui = NULL;
 	if (tmp_addrlen == 0)
 		goto out_err;
 
@@ -1313,10 +1433,10 @@
 		goto out_free_rawdata;
 	snprintf(dev_name, len + 5, "%s%s%s:/", startsep, ipaddr, endsep);
 
-	status = nfsd4_ssc_setup_dul(nn, ipaddr, &work, &ss_mnt);
+	status = nfsd4_ssc_setup_dul(nn, ipaddr, nsui);
 	if (status)
 		goto out_free_devname;
-	if (ss_mnt)
+	if ((*nsui)->nsui_vfsmount)
 		goto out_done;
 
 	/* Use an 'internal' mount: SB_KERNMOUNT -> MNT_INTERNAL */
@@ -1324,15 +1444,12 @@
 	module_put(type->owner);
 	if (IS_ERR(ss_mnt)) {
 		status = nfserr_nodev;
-		if (work)
-			nfsd4_ssc_cancel_dul_work(nn, work);
+		nfsd4_ssc_cancel_dul(nn, *nsui);
 		goto out_free_devname;
 	}
-	if (work)
-		nfsd4_ssc_update_dul_work(nn, work, ss_mnt);
+	nfsd4_ssc_update_dul(nn, *nsui, ss_mnt);
 out_done:
 	status = 0;
-	*mount = ss_mnt;
 
 out_free_devname:
 	kfree(dev_name);
@@ -1344,13 +1461,6 @@
 	return status;
 }
 
-static void
-nfsd4_interssc_disconnect(struct vfsmount *ss_mnt)
-{
-	nfs_do_sb_deactive(ss_mnt->mnt_sb);
-	mntput(ss_mnt);
-}
-
 /*
  * Verify COPY destination stateid.
  *
@@ -1363,7 +1473,7 @@
 static __be32
 nfsd4_setup_inter_ssc(struct svc_rqst *rqstp,
 		      struct nfsd4_compound_state *cstate,
-		      struct nfsd4_copy *copy, struct vfsmount **mount)
+		      struct nfsd4_copy *copy)
 {
 	struct svc_fh *s_fh = NULL;
 	stateid_t *s_stid = &copy->cp_src_stateid;
@@ -1376,14 +1486,14 @@
 	if (status)
 		goto out;
 
-	status = nfsd4_interssc_connect(&copy->cp_src, rqstp, mount);
+	status = nfsd4_interssc_connect(copy->cp_src, rqstp, &copy->ss_nsui);
 	if (status)
 		goto out;
 
 	s_fh = &cstate->save_fh;
 
 	copy->c_fh.size = s_fh->fh_handle.fh_size;
-	memcpy(copy->c_fh.data, &s_fh->fh_handle.fh_base, copy->c_fh.size);
+	memcpy(copy->c_fh.data, &s_fh->fh_handle.fh_raw, copy->c_fh.size);
 	copy->stateid.seqid = cpu_to_be32(s_stid->si_generation);
 	memcpy(copy->stateid.other, (void *)&s_stid->si_opaque,
 	       sizeof(stateid_opaque_t));
@@ -1394,45 +1504,26 @@
 }
 
 static void
-nfsd4_cleanup_inter_ssc(struct vfsmount *ss_mnt, struct nfsd_file *src,
+nfsd4_cleanup_inter_ssc(struct nfsd4_ssc_umount_item *nsui, struct file *filp,
 			struct nfsd_file *dst)
 {
-	bool found = false;
-	long timeout;
-	struct nfsd4_ssc_umount_item *tmp;
-	struct nfsd4_ssc_umount_item *ni = NULL;
 	struct nfsd_net *nn = net_generic(dst->nf_net, nfsd_net_id);
+	long timeout = msecs_to_jiffies(nfsd4_ssc_umount_timeout);
 
-	nfs42_ssc_close(src->nf_file);
-	nfsd_file_put(dst);
-	fput(src->nf_file);
+	nfs42_ssc_close(filp);
+	fput(filp);
 
-	if (!nn) {
-		mntput(ss_mnt);
-		return;
-	}
 	spin_lock(&nn->nfsd_ssc_lock);
-	timeout = msecs_to_jiffies(nfsd4_ssc_umount_timeout);
-	list_for_each_entry_safe(ni, tmp, &nn->nfsd_ssc_mount_list, nsui_list) {
-		if (ni->nsui_vfsmount->mnt_sb == ss_mnt->mnt_sb) {
-			list_del(&ni->nsui_list);
-			/*
-			 * vfsmount can be shared by multiple exports,
-			 * decrement refcnt. If the count drops to 1 it
-			 * will be unmounted when nsui_expire expires.
-			 */
-			refcount_dec(&ni->nsui_refcnt);
-			ni->nsui_expire = jiffies + timeout;
-			list_add_tail(&ni->nsui_list, &nn->nfsd_ssc_mount_list);
-			found = true;
-			break;
-		}
-	}
+	list_del(&nsui->nsui_list);
+	/*
+	 * vfsmount can be shared by multiple exports,
+	 * decrement refcnt. If the count drops to 1 it
+	 * will be unmounted when nsui_expire expires.
+	 */
+	refcount_dec(&nsui->nsui_refcnt);
+	nsui->nsui_expire = jiffies + timeout;
+	list_add_tail(&nsui->nsui_list, &nn->nfsd_ssc_mount_list);
 	spin_unlock(&nn->nfsd_ssc_lock);
-	if (!found) {
-		mntput(ss_mnt);
-		return;
-	}
 }
 
 #else /* CONFIG_NFSD_V4_2_INTER_SSC */
@@ -1440,24 +1531,17 @@
 static __be32
 nfsd4_setup_inter_ssc(struct svc_rqst *rqstp,
 		      struct nfsd4_compound_state *cstate,
-		      struct nfsd4_copy *copy,
-		      struct vfsmount **mount)
+		      struct nfsd4_copy *copy)
 {
-	*mount = NULL;
 	return nfserr_inval;
 }
 
 static void
-nfsd4_cleanup_inter_ssc(struct vfsmount *ss_mnt, struct nfsd_file *src,
+nfsd4_cleanup_inter_ssc(struct nfsd4_ssc_umount_item *nsui, struct file *filp,
 			struct nfsd_file *dst)
 {
 }
 
-static void
-nfsd4_interssc_disconnect(struct vfsmount *ss_mnt)
-{
-}
-
 static struct file *nfs42_ssc_open(struct vfsmount *ss_mnt,
 				   struct nfs_fh *src_fh,
 				   nfs4_stateid *stateid)
@@ -1476,23 +1560,21 @@
 				 &copy->nf_dst);
 }
 
-static void
-nfsd4_cleanup_intra_ssc(struct nfsd_file *src, struct nfsd_file *dst)
-{
-	nfsd_file_put(src);
-	nfsd_file_put(dst);
-}
-
 static void nfsd4_cb_offload_release(struct nfsd4_callback *cb)
 {
-	struct nfsd4_copy *copy = container_of(cb, struct nfsd4_copy, cp_cb);
+	struct nfsd4_cb_offload *cbo =
+		container_of(cb, struct nfsd4_cb_offload, co_cb);
 
-	nfs4_put_copy(copy);
+	kfree(cbo);
 }
 
 static int nfsd4_cb_offload_done(struct nfsd4_callback *cb,
 				 struct rpc_task *task)
 {
+	struct nfsd4_cb_offload *cbo =
+		container_of(cb, struct nfsd4_cb_offload, co_cb);
+
+	trace_nfsd_cb_offload_done(&cbo->co_res.cb_stateid, task);
 	return 1;
 }
 
@@ -1504,18 +1586,22 @@
 static void nfsd4_init_copy_res(struct nfsd4_copy *copy, bool sync)
 {
 	copy->cp_res.wr_stable_how =
-		copy->committed ? NFS_FILE_SYNC : NFS_UNSTABLE;
-	copy->cp_synchronous = sync;
-	gen_boot_verifier(&copy->cp_res.wr_verifier, copy->cp_clp->net);
+		test_bit(NFSD4_COPY_F_COMMITTED, &copy->cp_flags) ?
+			NFS_FILE_SYNC : NFS_UNSTABLE;
+	nfsd4_copy_set_sync(copy, sync);
 }
 
-static ssize_t _nfsd_copy_file_range(struct nfsd4_copy *copy)
+static ssize_t _nfsd_copy_file_range(struct nfsd4_copy *copy,
+				     struct file *dst,
+				     struct file *src)
 {
+	errseq_t since;
 	ssize_t bytes_copied = 0;
 	u64 bytes_total = copy->cp_count;
 	u64 src_pos = copy->cp_src_pos;
 	u64 dst_pos = copy->cp_dst_pos;
-	__be32 status;
+	int status;
+	loff_t end;
 
 	/* See RFC 7862 p.67: */
 	if (bytes_total == 0)
@@ -1523,35 +1609,37 @@
 	do {
 		if (kthread_should_stop())
 			break;
-		bytes_copied = nfsd_copy_file_range(copy->nf_src->nf_file,
-				src_pos, copy->nf_dst->nf_file, dst_pos,
-				bytes_total);
+		bytes_copied = nfsd_copy_file_range(src, src_pos, dst, dst_pos,
+						    bytes_total);
 		if (bytes_copied <= 0)
 			break;
 		bytes_total -= bytes_copied;
 		copy->cp_res.wr_bytes_written += bytes_copied;
 		src_pos += bytes_copied;
 		dst_pos += bytes_copied;
-	} while (bytes_total > 0 && !copy->cp_synchronous);
+	} while (bytes_total > 0 && nfsd4_copy_is_async(copy));
 	/* for a non-zero asynchronous copy do a commit of data */
-	if (!copy->cp_synchronous && copy->cp_res.wr_bytes_written > 0) {
-		down_write(&copy->nf_dst->nf_rwsem);
-		status = vfs_fsync_range(copy->nf_dst->nf_file,
-					 copy->cp_dst_pos,
-					 copy->cp_res.wr_bytes_written, 0);
-		up_write(&copy->nf_dst->nf_rwsem);
+	if (nfsd4_copy_is_async(copy) && copy->cp_res.wr_bytes_written > 0) {
+		since = READ_ONCE(dst->f_wb_err);
+		end = copy->cp_dst_pos + copy->cp_res.wr_bytes_written - 1;
+		status = vfs_fsync_range(dst, copy->cp_dst_pos, end, 0);
 		if (!status)
-			copy->committed = true;
+			status = filemap_check_wb_err(dst->f_mapping, since);
+		if (!status)
+			set_bit(NFSD4_COPY_F_COMMITTED, &copy->cp_flags);
 	}
 	return bytes_copied;
 }
 
-static __be32 nfsd4_do_copy(struct nfsd4_copy *copy, bool sync)
+static __be32 nfsd4_do_copy(struct nfsd4_copy *copy,
+			    struct file *src, struct file *dst,
+			    bool sync)
 {
 	__be32 status;
 	ssize_t bytes;
 
-	bytes = _nfsd_copy_file_range(copy);
+	bytes = _nfsd_copy_file_range(copy, dst, src);
+
 	/* for async copy, we ignore the error, client can always retry
 	 * to get the error
 	 */
@@ -1561,13 +1649,6 @@
 		nfsd4_init_copy_res(copy, sync);
 		status = nfs_ok;
 	}
-
-	if (!copy->cp_intra) /* Inter server SSC */
-		nfsd4_cleanup_inter_ssc(copy->ss_mnt, copy->nf_src,
-					copy->nf_dst);
-	else
-		nfsd4_cleanup_intra_ssc(copy->nf_src, copy->nf_dst);
-
 	return status;
 }
 
@@ -1576,73 +1657,100 @@
 	dst->cp_src_pos = src->cp_src_pos;
 	dst->cp_dst_pos = src->cp_dst_pos;
 	dst->cp_count = src->cp_count;
-	dst->cp_synchronous = src->cp_synchronous;
+	dst->cp_flags = src->cp_flags;
 	memcpy(&dst->cp_res, &src->cp_res, sizeof(src->cp_res));
 	memcpy(&dst->fh, &src->fh, sizeof(src->fh));
 	dst->cp_clp = src->cp_clp;
 	dst->nf_dst = nfsd_file_get(src->nf_dst);
-	dst->cp_intra = src->cp_intra;
-	if (src->cp_intra) /* for inter, file_src doesn't exist yet */
+	/* for inter, nf_src doesn't exist yet */
+	if (!nfsd4_ssc_is_inter(src))
 		dst->nf_src = nfsd_file_get(src->nf_src);
 
 	memcpy(&dst->cp_stateid, &src->cp_stateid, sizeof(src->cp_stateid));
-	memcpy(&dst->cp_src, &src->cp_src, sizeof(struct nl4_server));
+	memcpy(dst->cp_src, src->cp_src, sizeof(struct nl4_server));
 	memcpy(&dst->stateid, &src->stateid, sizeof(src->stateid));
 	memcpy(&dst->c_fh, &src->c_fh, sizeof(src->c_fh));
-	dst->ss_mnt = src->ss_mnt;
+	dst->ss_nsui = src->ss_nsui;
+}
+
+static void release_copy_files(struct nfsd4_copy *copy)
+{
+	if (copy->nf_src)
+		nfsd_file_put(copy->nf_src);
+	if (copy->nf_dst)
+		nfsd_file_put(copy->nf_dst);
 }
 
 static void cleanup_async_copy(struct nfsd4_copy *copy)
 {
 	nfs4_free_copy_state(copy);
-	nfsd_file_put(copy->nf_dst);
-	if (copy->cp_intra)
-		nfsd_file_put(copy->nf_src);
-	spin_lock(&copy->cp_clp->async_lock);
-	list_del(&copy->copies);
-	spin_unlock(&copy->cp_clp->async_lock);
+	release_copy_files(copy);
+	if (copy->cp_clp) {
+		spin_lock(&copy->cp_clp->async_lock);
+		if (!list_empty(&copy->copies))
+			list_del_init(&copy->copies);
+		spin_unlock(&copy->cp_clp->async_lock);
+	}
 	nfs4_put_copy(copy);
 }
 
+static void nfsd4_send_cb_offload(struct nfsd4_copy *copy, __be32 nfserr)
+{
+	struct nfsd4_cb_offload *cbo;
+
+	cbo = kzalloc(sizeof(*cbo), GFP_KERNEL);
+	if (!cbo)
+		return;
+
+	memcpy(&cbo->co_res, &copy->cp_res, sizeof(copy->cp_res));
+	memcpy(&cbo->co_fh, &copy->fh, sizeof(copy->fh));
+	cbo->co_nfserr = nfserr;
+
+	nfsd4_init_cb(&cbo->co_cb, copy->cp_clp, &nfsd4_cb_offload_ops,
+		      NFSPROC4_CLNT_CB_OFFLOAD);
+	trace_nfsd_cb_offload(copy->cp_clp, &cbo->co_res.cb_stateid,
+			      &cbo->co_fh, copy->cp_count, nfserr);
+	nfsd4_run_cb(&cbo->co_cb);
+}
+
+/**
+ * nfsd4_do_async_copy - kthread function for background server-side COPY
+ * @data: arguments for COPY operation
+ *
+ * Return values:
+ *   %0: Copy operation is done.
+ */
 static int nfsd4_do_async_copy(void *data)
 {
 	struct nfsd4_copy *copy = (struct nfsd4_copy *)data;
-	struct nfsd4_copy *cb_copy;
+	__be32 nfserr;
 
-	if (!copy->cp_intra) { /* Inter server SSC */
-		copy->nf_src = kzalloc(sizeof(struct nfsd_file), GFP_KERNEL);
-		if (!copy->nf_src) {
-			copy->nfserr = nfserr_serverfault;
-			nfsd4_interssc_disconnect(copy->ss_mnt);
-			goto do_callback;
-		}
-		copy->nf_src->nf_file = nfs42_ssc_open(copy->ss_mnt, &copy->c_fh,
-					      &copy->stateid);
-		if (IS_ERR(copy->nf_src->nf_file)) {
-			copy->nfserr = nfserr_offload_denied;
-			nfsd4_interssc_disconnect(copy->ss_mnt);
+	if (nfsd4_ssc_is_inter(copy)) {
+		struct file *filp;
+
+		filp = nfs42_ssc_open(copy->ss_nsui->nsui_vfsmount,
+				      &copy->c_fh, &copy->stateid);
+		if (IS_ERR(filp)) {
+			switch (PTR_ERR(filp)) {
+			case -EBADF:
+				nfserr = nfserr_wrong_type;
+				break;
+			default:
+				nfserr = nfserr_offload_denied;
+			}
+			/* ss_mnt will be unmounted by the laundromat */
 			goto do_callback;
 		}
+		nfserr = nfsd4_do_copy(copy, filp, copy->nf_dst->nf_file,
+				       false);
+		nfsd4_cleanup_inter_ssc(copy->ss_nsui, filp, copy->nf_dst);
+	} else {
+		nfserr = nfsd4_do_copy(copy, copy->nf_src->nf_file,
+				       copy->nf_dst->nf_file, false);
 	}
 
-	copy->nfserr = nfsd4_do_copy(copy, 0);
 do_callback:
-	cb_copy = kzalloc(sizeof(struct nfsd4_copy), GFP_KERNEL);
-	if (!cb_copy)
-		goto out;
-	refcount_set(&cb_copy->refcount, 1);
-	memcpy(&cb_copy->cp_res, &copy->cp_res, sizeof(copy->cp_res));
-	cb_copy->cp_clp = copy->cp_clp;
-	cb_copy->nfserr = copy->nfserr;
-	memcpy(&cb_copy->fh, &copy->fh, sizeof(copy->fh));
-	nfsd4_init_cb(&cb_copy->cp_cb, cb_copy->cp_clp,
-			&nfsd4_cb_offload_ops, NFSPROC4_CLNT_CB_OFFLOAD);
-	trace_nfsd_cb_offload(copy->cp_clp, &copy->cp_res.cb_stateid,
-			      &copy->fh, copy->cp_count, copy->nfserr);
-	nfsd4_run_cb(&cb_copy->cp_cb);
-out:
-	if (!copy->cp_intra)
-		kfree(copy->nf_src);
+	nfsd4_send_cb_offload(copy, nfserr);
 	cleanup_async_copy(copy);
 	return 0;
 }
@@ -1651,17 +1759,22 @@
 nfsd4_copy(struct svc_rqst *rqstp, struct nfsd4_compound_state *cstate,
 		union nfsd4_op_u *u)
 {
+	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
+	struct nfsd4_copy *async_copy = NULL;
 	struct nfsd4_copy *copy = &u->copy;
+	struct nfsd42_write_res *result;
 	__be32 status;
-	struct nfsd4_copy *async_copy = NULL;
 
-	if (!copy->cp_intra) { /* Inter server SSC */
-		if (!inter_copy_offload_enable || copy->cp_synchronous) {
+	result = &copy->cp_res;
+	nfsd_copy_write_verifier((__be32 *)&result->wr_verifier.data, nn);
+
+	copy->cp_clp = cstate->clp;
+	if (nfsd4_ssc_is_inter(copy)) {
+		if (!inter_copy_offload_enable || nfsd4_copy_is_sync(copy)) {
 			status = nfserr_notsupp;
 			goto out;
 		}
-		status = nfsd4_setup_inter_ssc(rqstp, cstate, copy,
-				&copy->ss_mnt);
+		status = nfsd4_setup_inter_ssc(rqstp, cstate, copy);
 		if (status)
 			return nfserr_offload_denied;
 	} else {
@@ -1670,21 +1783,26 @@
 			return status;
 	}
 
-	copy->cp_clp = cstate->clp;
 	memcpy(&copy->fh, &cstate->current_fh.fh_handle,
 		sizeof(struct knfsd_fh));
-	if (!copy->cp_synchronous) {
-		struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
-
-		status = nfserrno(-ENOMEM);
+	if (nfsd4_copy_is_async(copy)) {
 		async_copy = kzalloc(sizeof(struct nfsd4_copy), GFP_KERNEL);
 		if (!async_copy)
 			goto out_err;
+		async_copy->cp_nn = nn;
+		INIT_LIST_HEAD(&async_copy->copies);
+		refcount_set(&async_copy->refcount, 1);
+		/* Arbitrary cap on number of pending async copy operations */
+		if (atomic_inc_return(&nn->pending_async_copies) >
+				(int)rqstp->rq_pool->sp_nrthreads)
+			goto out_err;
+		async_copy->cp_src = kmalloc(sizeof(*async_copy->cp_src), GFP_KERNEL);
+		if (!async_copy->cp_src)
+			goto out_err;
 		if (!nfs4_init_copy_state(nn, copy))
 			goto out_err;
-		refcount_set(&async_copy->refcount, 1);
-		memcpy(&copy->cp_res.cb_stateid, &copy->cp_stateid.stid,
-			sizeof(copy->cp_res.cb_stateid));
+		memcpy(&result->cb_stateid, &copy->cp_stateid.cs_stid,
+			sizeof(result->cb_stateid));
 		dup_copy_fields(copy, async_copy);
 		async_copy->copy_task = kthread_create(nfsd4_do_async_copy,
 				async_copy, "%s", "copy thread");
@@ -1697,16 +1815,24 @@
 		wake_up_process(async_copy->copy_task);
 		status = nfs_ok;
 	} else {
-		status = nfsd4_do_copy(copy, 1);
+		status = nfsd4_do_copy(copy, copy->nf_src->nf_file,
+				       copy->nf_dst->nf_file, true);
 	}
 out:
+	release_copy_files(copy);
 	return status;
 out_err:
+	if (nfsd4_ssc_is_inter(copy)) {
+		/*
+		 * Source's vfsmount of inter-copy will be unmounted
+		 * by the laundromat. Use copy instead of async_copy
+		 * since async_copy->ss_nsui might not be set yet.
+		 */
+		refcount_dec(&copy->ss_nsui->nsui_refcnt);
+	}
 	if (async_copy)
 		cleanup_async_copy(async_copy);
-	status = nfserrno(-ENOMEM);
-	if (!copy->cp_intra)
-		nfsd4_interssc_disconnect(copy->ss_mnt);
+	status = nfserr_jukebox;
 	goto out;
 }
 
@@ -1717,7 +1843,7 @@
 
 	spin_lock(&clp->async_lock);
 	list_for_each_entry(copy, &clp->async_copies, copies) {
-		if (memcmp(&copy->cp_stateid.stid, stateid, NFS4_STATEID_SIZE))
+		if (memcmp(&copy->cp_stateid.cs_stid, stateid, NFS4_STATEID_SIZE))
 			continue;
 		refcount_inc(&copy->refcount);
 		spin_unlock(&clp->async_lock);
@@ -1771,16 +1897,16 @@
 	cps = nfs4_alloc_init_cpntf_state(nn, stid);
 	if (!cps)
 		goto out;
-	memcpy(&cn->cpn_cnr_stateid, &cps->cp_stateid.stid, sizeof(stateid_t));
+	memcpy(&cn->cpn_cnr_stateid, &cps->cp_stateid.cs_stid, sizeof(stateid_t));
 	memcpy(&cps->cp_p_stateid, &stid->sc_stateid, sizeof(stateid_t));
 	memcpy(&cps->cp_p_clid, &clp->cl_clientid, sizeof(clientid_t));
 
 	/* For now, only return one server address in cpn_src, the
 	 * address used by the client to connect to this server.
 	 */
-	cn->cpn_src.nl4_type = NL4_NETADDR;
+	cn->cpn_src->nl4_type = NL4_NETADDR;
 	status = nfsd4_set_netaddr((struct sockaddr *)&rqstp->rq_daddr,
-				 &cn->cpn_src.u.nl4_addr);
+				 &cn->cpn_src->u.nl4_addr);
 	WARN_ON_ONCE(status);
 	if (status) {
 		nfs4_put_cpntf_state(nn, cps);
@@ -1801,10 +1927,8 @@
 	status = nfs4_preprocess_stateid_op(rqstp, cstate, &cstate->current_fh,
 					    &fallocate->falloc_stateid,
 					    WR_STATE, &nf, NULL);
-	if (status != nfs_ok) {
-		dprintk("NFSD: nfsd4_fallocate: couldn't process stateid!\n");
+	if (status != nfs_ok)
 		return status;
-	}
 
 	status = nfsd4_vfs_fallocate(rqstp, &cstate->current_fh, nf->nf_file,
 				     fallocate->falloc_offset,
@@ -1860,10 +1984,8 @@
 	status = nfs4_preprocess_stateid_op(rqstp, cstate, &cstate->current_fh,
 					    &seek->seek_stateid,
 					    RD_STATE, &nf, NULL);
-	if (status) {
-		dprintk("NFSD: nfsd4_seek: couldn't process stateid!\n");
+	if (status)
 		return status;
-	}
 
 	switch (seek->seek_whence) {
 	case NFS4_CONTENT_DATA:
@@ -2314,10 +2436,10 @@
 	return rpc_success;
 }
 
-static inline void nfsd4_increment_op_stats(u32 opnum)
+static inline void nfsd4_increment_op_stats(struct nfsd_net *nn, u32 opnum)
 {
 	if (opnum >= FIRST_NFS4_OP && opnum <= LAST_NFS4_OP)
-		percpu_counter_inc(&nfsdstats.counter[NFSD_STATS_NFS4_OP(opnum)]);
+		percpu_counter_inc(&nn->counter[NFSD_STATS_NFS4_OP(opnum)]);
 }
 
 static const struct nfsd4_operation nfsd4_ops[];
@@ -2434,7 +2556,7 @@
 				return;
 			}
 			putfh = (struct nfsd4_putfh *)&saved_op->u;
-			if (!copy->cp_intra)
+			if (nfsd4_ssc_is_inter(copy))
 				putfh->no_verify = true;
 		}
 	}
@@ -2462,11 +2584,11 @@
 	__be32		status;
 
 	resp->xdr = &rqstp->rq_res_stream;
+	resp->statusp = resp->xdr->p;
 
 	/* reserve space for: NFS status code */
 	xdr_reserve_space(resp->xdr, XDR_UNIT);
 
-	resp->tagp = resp->xdr->p;
 	/* reserve space for: taglen, tag, and opcnt */
 	xdr_reserve_space(resp->xdr, XDR_UNIT * 2 + args->taglen);
 	resp->taglen = args->taglen;
@@ -2487,9 +2609,6 @@
 	status = nfserr_minor_vers_mismatch;
 	if (nfsd_minorversion(nn, args->minorversion, NFSD_TEST) <= 0)
 		goto out;
-	status = nfserr_resource;
-	if (args->opcnt > NFSD_MAX_OPS_PER_COMPOUND)
-		goto out;
 
 	status = nfs41_check_op_ordering(args);
 	if (status) {
@@ -2502,10 +2621,20 @@
 
 	rqstp->rq_lease_breaker = (void **)&cstate->clp;
 
-	trace_nfsd_compound(rqstp, args->opcnt);
+	trace_nfsd_compound(rqstp, args->tag, args->taglen, args->client_opcnt);
 	while (!status && resp->opcnt < args->opcnt) {
 		op = &args->ops[resp->opcnt++];
 
+		if (unlikely(resp->opcnt == NFSD_MAX_OPS_PER_COMPOUND)) {
+			/* If there are still more operations to process,
+			 * stop here and report NFS4ERR_RESOURCE. */
+			if (cstate->minorversion == 0 &&
+			    args->client_opcnt > resp->opcnt) {
+				op->status = nfserr_resource;
+				goto encode_op;
+			}
+		}
+
 		/*
 		 * The XDR decode routines may have pre-set op->status;
 		 * for example, if there is a miscellaneous XDR error
@@ -2529,13 +2658,13 @@
 			goto encode_op;
 		}
 
-		fh_clear_wcc(current_fh);
+		fh_clear_pre_post_attrs(current_fh);
 
 		/* If op is non-idempotent */
 		if (op->opdesc->op_flags & OP_MODIFIES_SOMETHING) {
 			/*
 			 * Don't execute this op if we couldn't encode a
-			 * succesful reply:
+			 * successful reply:
 			 */
 			u32 plen = op->opdesc->op_rsize_bop(rqstp, op);
 			/*
@@ -2581,11 +2710,11 @@
 			status = op->status;
 		}
 
-		trace_nfsd_compound_status(args->opcnt, resp->opcnt, status,
-					   nfsd4_op_name(op->opnum));
+		trace_nfsd_compound_status(args->client_opcnt, resp->opcnt,
+					   status, nfsd4_op_name(op->opnum));
 
 		nfsd4_cstate_clear_replay(cstate);
-		nfsd4_increment_op_stats(op->opnum);
+		nfsd4_increment_op_stats(nn, op->opnum);
 	}
 
 	fh_put(current_fh);
@@ -2616,28 +2745,49 @@
 
 #define op_encode_channel_attrs_maxsz	(6 + 1 + 1)
 
-static inline u32 nfsd4_only_status_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+/*
+ * The _rsize() helpers are invoked by the NFSv4 COMPOUND decoder, which
+ * is called before sunrpc sets rq_res.buflen. Thus we have to compute
+ * the maximum payload size here, based on transport limits and the size
+ * of the remaining space in the rq_pages array.
+ */
+static u32 nfsd4_max_payload(const struct svc_rqst *rqstp)
+{
+	u32 buflen;
+
+	buflen = (rqstp->rq_page_end - rqstp->rq_next_page) * PAGE_SIZE;
+	buflen -= rqstp->rq_auth_slack;
+	buflen -= rqstp->rq_res.head[0].iov_len;
+	return min_t(u32, buflen, svc_max_payload(rqstp));
+}
+
+static u32 nfsd4_only_status_rsize(const struct svc_rqst *rqstp,
+				   const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_status_stateid_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_status_stateid_rsize(const struct svc_rqst *rqstp,
+				      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_stateid_maxsz)* sizeof(__be32);
 }
 
-static inline u32 nfsd4_access_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_access_rsize(const struct svc_rqst *rqstp,
+			      const struct nfsd4_op *op)
 {
 	/* ac_supported, ac_resp_access */
 	return (op_encode_hdr_size + 2)* sizeof(__be32);
 }
 
-static inline u32 nfsd4_commit_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_commit_rsize(const struct svc_rqst *rqstp,
+			      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_verifier_maxsz) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_create_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_create_rsize(const struct svc_rqst *rqstp,
+			      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_change_info_maxsz
 		+ nfs4_fattr_bitmap_maxsz) * sizeof(__be32);
@@ -2648,17 +2798,17 @@
  * the op prematurely if the estimate is too large.  We may turn off splice
  * reads unnecessarily.
  */
-static inline u32 nfsd4_getattr_rsize(struct svc_rqst *rqstp,
-				      struct nfsd4_op *op)
+static u32 nfsd4_getattr_rsize(const struct svc_rqst *rqstp,
+			       const struct nfsd4_op *op)
 {
-	u32 *bmap = op->u.getattr.ga_bmval;
+	const u32 *bmap = op->u.getattr.ga_bmval;
 	u32 bmap0 = bmap[0], bmap1 = bmap[1], bmap2 = bmap[2];
 	u32 ret = 0;
 
 	if (bmap0 & FATTR4_WORD0_ACL)
-		return svc_max_payload(rqstp);
+		return nfsd4_max_payload(rqstp);
 	if (bmap0 & FATTR4_WORD0_FS_LOCATIONS)
-		return svc_max_payload(rqstp);
+		return nfsd4_max_payload(rqstp);
 
 	if (bmap1 & FATTR4_WORD1_OWNER) {
 		ret += IDMAP_NAMESZ + 4;
@@ -2686,24 +2836,28 @@
 	return ret;
 }
 
-static inline u32 nfsd4_getfh_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_getfh_rsize(const struct svc_rqst *rqstp,
+			     const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 1) * sizeof(__be32) + NFS4_FHSIZE;
 }
 
-static inline u32 nfsd4_link_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_link_rsize(const struct svc_rqst *rqstp,
+			    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_change_info_maxsz)
 		* sizeof(__be32);
 }
 
-static inline u32 nfsd4_lock_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_lock_rsize(const struct svc_rqst *rqstp,
+			    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_lock_denied_maxsz)
 		* sizeof(__be32);
 }
 
-static inline u32 nfsd4_open_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_open_rsize(const struct svc_rqst *rqstp,
+			    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_stateid_maxsz
 		+ op_encode_change_info_maxsz + 1
@@ -2711,20 +2865,18 @@
 		+ op_encode_delegation_maxsz) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_read_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_read_rsize(const struct svc_rqst *rqstp,
+			    const struct nfsd4_op *op)
 {
-	u32 maxcount = 0, rlen = 0;
-
-	maxcount = svc_max_payload(rqstp);
-	rlen = min(op->u.read.rd_length, maxcount);
+	u32 rlen = min(op->u.read.rd_length, nfsd4_max_payload(rqstp));
 
 	return (op_encode_hdr_size + 2 + XDR_QUADLEN(rlen)) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_read_plus_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_read_plus_rsize(const struct svc_rqst *rqstp,
+				 const struct nfsd4_op *op)
 {
-	u32 maxcount = svc_max_payload(rqstp);
-	u32 rlen = min(op->u.read.rd_length, maxcount);
+	u32 rlen = min(op->u.read.rd_length, nfsd4_max_payload(rqstp));
 	/*
 	 * If we detect that the file changed during hole encoding, then we
 	 * recover by encoding the remaining reply as data. This means we need
@@ -2735,70 +2887,77 @@
 	return (op_encode_hdr_size + 2 + seg_len + XDR_QUADLEN(rlen)) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_readdir_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_readdir_rsize(const struct svc_rqst *rqstp,
+			       const struct nfsd4_op *op)
 {
-	u32 maxcount = 0, rlen = 0;
-
-	maxcount = svc_max_payload(rqstp);
-	rlen = min(op->u.readdir.rd_maxcount, maxcount);
+	u32 rlen = min(op->u.readdir.rd_maxcount, nfsd4_max_payload(rqstp));
 
 	return (op_encode_hdr_size + op_encode_verifier_maxsz +
 		XDR_QUADLEN(rlen)) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_readlink_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_readlink_rsize(const struct svc_rqst *rqstp,
+				const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 1) * sizeof(__be32) + PAGE_SIZE;
 }
 
-static inline u32 nfsd4_remove_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_remove_rsize(const struct svc_rqst *rqstp,
+			      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_change_info_maxsz)
 		* sizeof(__be32);
 }
 
-static inline u32 nfsd4_rename_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_rename_rsize(const struct svc_rqst *rqstp,
+			      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_change_info_maxsz
 		+ op_encode_change_info_maxsz) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_sequence_rsize(struct svc_rqst *rqstp,
-				       struct nfsd4_op *op)
+static u32 nfsd4_sequence_rsize(const struct svc_rqst *rqstp,
+				const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size
 		+ XDR_QUADLEN(NFS4_MAX_SESSIONID_LEN) + 5) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_test_stateid_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_test_stateid_rsize(const struct svc_rqst *rqstp,
+				    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 1 + op->u.test_stateid.ts_num_ids)
 		* sizeof(__be32);
 }
 
-static inline u32 nfsd4_setattr_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_setattr_rsize(const struct svc_rqst *rqstp,
+			       const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + nfs4_fattr_bitmap_maxsz) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_secinfo_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_secinfo_rsize(const struct svc_rqst *rqstp,
+			       const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + RPC_AUTH_MAXFLAVOR *
 		(4 + XDR_QUADLEN(GSS_OID_MAX_LEN))) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_setclientid_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_setclientid_rsize(const struct svc_rqst *rqstp,
+				   const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 2 + XDR_QUADLEN(NFS4_VERIFIER_SIZE)) *
 								sizeof(__be32);
 }
 
-static inline u32 nfsd4_write_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_write_rsize(const struct svc_rqst *rqstp,
+			     const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 2 + op_encode_verifier_maxsz) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_exchange_id_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_exchange_id_rsize(const struct svc_rqst *rqstp,
+				   const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 2 + 1 + /* eir_clientid, eir_sequenceid */\
 		1 + 1 + /* eir_flags, spr_how */\
@@ -2812,14 +2971,16 @@
 		0 /* ignored eir_server_impl_id contents */) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_bind_conn_to_session_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_bind_conn_to_session_rsize(const struct svc_rqst *rqstp,
+					    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + \
 		XDR_QUADLEN(NFS4_MAX_SESSIONID_LEN) + /* bctsr_sessid */\
 		2 /* bctsr_dir, use_conn_in_rdma_mode */) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_create_session_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_create_session_rsize(const struct svc_rqst *rqstp,
+				      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + \
 		XDR_QUADLEN(NFS4_MAX_SESSIONID_LEN) + /* sessionid */\
@@ -2828,7 +2989,8 @@
 		op_encode_channel_attrs_maxsz) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_copy_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_copy_rsize(const struct svc_rqst *rqstp,
+			    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size +
 		1 /* wr_callback */ +
@@ -2840,16 +3002,16 @@
 		1 /* cr_synchronous */) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_offload_status_rsize(struct svc_rqst *rqstp,
-					     struct nfsd4_op *op)
+static u32 nfsd4_offload_status_rsize(const struct svc_rqst *rqstp,
+				      const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size +
 		2 /* osr_count */ +
 		1 /* osr_complete<1> optional 0 for now */) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_copy_notify_rsize(struct svc_rqst *rqstp,
-					struct nfsd4_op *op)
+static u32 nfsd4_copy_notify_rsize(const struct svc_rqst *rqstp,
+				   const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size +
 		3 /* cnr_lease_time */ +
@@ -2864,12 +3026,10 @@
 }
 
 #ifdef CONFIG_NFSD_PNFS
-static inline u32 nfsd4_getdeviceinfo_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_getdeviceinfo_rsize(const struct svc_rqst *rqstp,
+				     const struct nfsd4_op *op)
 {
-	u32 maxcount = 0, rlen = 0;
-
-	maxcount = svc_max_payload(rqstp);
-	rlen = min(op->u.getdeviceinfo.gd_maxcount, maxcount);
+	u32 rlen = min(op->u.getdeviceinfo.gd_maxcount, nfsd4_max_payload(rqstp));
 
 	return (op_encode_hdr_size +
 		1 /* gd_layout_type*/ +
@@ -2882,7 +3042,8 @@
  * so we need to define an arbitrary upper bound here.
  */
 #define MAX_LAYOUT_SIZE		128
-static inline u32 nfsd4_layoutget_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_layoutget_rsize(const struct svc_rqst *rqstp,
+				 const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size +
 		1 /* logr_return_on_close */ +
@@ -2891,14 +3052,16 @@
 		MAX_LAYOUT_SIZE) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_layoutcommit_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_layoutcommit_rsize(const struct svc_rqst *rqstp,
+				    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size +
 		1 /* locr_newsize */ +
 		2 /* ns_size */) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_layoutreturn_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_layoutreturn_rsize(const struct svc_rqst *rqstp,
+				    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size +
 		1 /* lrs_stateid */ +
@@ -2907,41 +3070,36 @@
 #endif /* CONFIG_NFSD_PNFS */
 
 
-static inline u32 nfsd4_seek_rsize(struct svc_rqst *rqstp, struct nfsd4_op *op)
+static u32 nfsd4_seek_rsize(const struct svc_rqst *rqstp,
+			    const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + 3) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_getxattr_rsize(struct svc_rqst *rqstp,
-				       struct nfsd4_op *op)
+static u32 nfsd4_getxattr_rsize(const struct svc_rqst *rqstp,
+				const struct nfsd4_op *op)
 {
-	u32 maxcount, rlen;
-
-	maxcount = svc_max_payload(rqstp);
-	rlen = min_t(u32, XATTR_SIZE_MAX, maxcount);
+	u32 rlen = min_t(u32, XATTR_SIZE_MAX, nfsd4_max_payload(rqstp));
 
 	return (op_encode_hdr_size + 1 + XDR_QUADLEN(rlen)) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_setxattr_rsize(struct svc_rqst *rqstp,
-				       struct nfsd4_op *op)
+static u32 nfsd4_setxattr_rsize(const struct svc_rqst *rqstp,
+				const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_change_info_maxsz)
 		* sizeof(__be32);
 }
-static inline u32 nfsd4_listxattrs_rsize(struct svc_rqst *rqstp,
-					 struct nfsd4_op *op)
+static u32 nfsd4_listxattrs_rsize(const struct svc_rqst *rqstp,
+				  const struct nfsd4_op *op)
 {
-	u32 maxcount, rlen;
-
-	maxcount = svc_max_payload(rqstp);
-	rlen = min(op->u.listxattrs.lsxa_maxcount, maxcount);
+	u32 rlen = min(op->u.listxattrs.lsxa_maxcount, nfsd4_max_payload(rqstp));
 
 	return (op_encode_hdr_size + 4 + XDR_QUADLEN(rlen)) * sizeof(__be32);
 }
 
-static inline u32 nfsd4_removexattr_rsize(struct svc_rqst *rqstp,
-					  struct nfsd4_op *op)
+static u32 nfsd4_removexattr_rsize(const struct svc_rqst *rqstp,
+				   const struct nfsd4_op *op)
 {
 	return (op_encode_hdr_size + op_encode_change_info_maxsz)
 		* sizeof(__be32);
@@ -3430,6 +3588,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = 1,
@@ -3440,6 +3599,7 @@
 		.pc_decode = nfs4svc_decode_compoundargs,
 		.pc_encode = nfs4svc_encode_compoundres,
 		.pc_argsize = sizeof(struct nfsd4_compoundargs),
+		.pc_argzero = offsetof(struct nfsd4_compoundargs, iops),
 		.pc_ressize = sizeof(struct nfsd4_compoundres),
 		.pc_release = nfsd4_release_compoundargs,
 		.pc_cachetype = RC_NOCACHE,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4recover.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4recover.c
@@ -658,7 +658,8 @@
 		return status;
 	status = -ENOTDIR;
 	if (d_is_dir(path.dentry)) {
-		strcpy(user_recovery_dirname, recdir);
+		strscpy(user_recovery_dirname, recdir,
+			sizeof(user_recovery_dirname));
 		status = 0;
 	}
 	path_put(&path);
@@ -806,17 +807,23 @@
 			ci = &cmsg->cm_u.cm_clntinfo;
 			if (get_user(namelen, &ci->cc_name.cn_len))
 				return -EFAULT;
+			if (!namelen) {
+				dprintk("%s: namelen should not be zero", __func__);
+				return -EINVAL;
+			}
 			name.data = memdup_user(&ci->cc_name.cn_id, namelen);
-			if (IS_ERR_OR_NULL(name.data))
-				return -EFAULT;
+			if (IS_ERR(name.data))
+				return PTR_ERR(name.data);
 			name.len = namelen;
 			get_user(princhashlen, &ci->cc_princhash.cp_len);
 			if (princhashlen > 0) {
 				princhash.data = memdup_user(
 						&ci->cc_princhash.cp_data,
 						princhashlen);
-				if (IS_ERR_OR_NULL(princhash.data))
-					return -EFAULT;
+				if (IS_ERR(princhash.data)) {
+					kfree(name.data);
+					return PTR_ERR(princhash.data);
+				}
 				princhash.len = princhashlen;
 			} else
 				princhash.len = 0;
@@ -826,9 +833,13 @@
 			cnm = &cmsg->cm_u.cm_name;
 			if (get_user(namelen, &cnm->cn_len))
 				return -EFAULT;
+			if (!namelen) {
+				dprintk("%s: namelen should not be zero", __func__);
+				return -EINVAL;
+			}
 			name.data = memdup_user(&cnm->cn_id, namelen);
-			if (IS_ERR_OR_NULL(name.data))
-				return -EFAULT;
+			if (IS_ERR(name.data))
+				return PTR_ERR(name.data);
 			name.len = namelen;
 		}
 		if (name.len > 5 && memcmp(name.data, "hash:", 5) == 0) {
@@ -2156,6 +2167,7 @@
 int
 register_cld_notifier(void)
 {
+	WARN_ON(!nfsd_net_id);
 	return rpc_pipefs_notifier_register(&nfsd4_cld_block);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4state.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4state.c
@@ -44,7 +44,9 @@
 #include <linux/jhash.h>
 #include <linux/string_helpers.h>
 #include <linux/fsnotify.h>
+#include <linux/rhashtable.h>
 #include <linux/nfs_ssc.h>
+
 #include "xdr4.h"
 #include "xdr4cb.h"
 #include "vfs.h"
@@ -84,6 +86,7 @@
 static void nfs4_free_ol_stateid(struct nfs4_stid *stid);
 void nfsd4_end_grace(struct nfsd_net *nn);
 static void _free_cpntf_state_locked(struct nfsd_net *nn, struct nfs4_cpntf_state *cps);
+static void nfsd4_file_hash_remove(struct nfs4_file *fi);
 
 /* Locking: */
 
@@ -125,6 +128,23 @@
 static const struct nfsd4_callback_ops nfsd4_cb_recall_ops;
 static const struct nfsd4_callback_ops nfsd4_cb_notify_lock_ops;
 
+static struct workqueue_struct *laundry_wq;
+
+int nfsd4_create_laundry_wq(void)
+{
+	int rc = 0;
+
+	laundry_wq = alloc_workqueue("%s", WQ_UNBOUND, 0, "nfsd4");
+	if (laundry_wq == NULL)
+		rc = -ENOMEM;
+	return rc;
+}
+
+void nfsd4_destroy_laundry_wq(void)
+{
+	destroy_workqueue(laundry_wq);
+}
+
 static bool is_session_dead(struct nfsd4_session *ses)
 {
 	return ses->se_flags & NFS4_SESSION_DEAD;
@@ -143,6 +163,13 @@
 	return clp->cl_time == 0;
 }
 
+static void nfsd4_dec_courtesy_client_count(struct nfsd_net *nn,
+					struct nfs4_client *clp)
+{
+	if (clp->cl_state != NFSD4_ACTIVE)
+		atomic_add_unless(&nn->nfsd_courtesy_clients, -1, 0);
+}
+
 static __be32 get_client_locked(struct nfs4_client *clp)
 {
 	struct nfsd_net *nn = net_generic(clp->net, nfsd_net_id);
@@ -152,6 +179,8 @@
 	if (is_client_expired(clp))
 		return nfserr_expired;
 	atomic_inc(&clp->cl_rpc_users);
+	nfsd4_dec_courtesy_client_count(nn, clp);
+	clp->cl_state = NFSD4_ACTIVE;
 	return nfs_ok;
 }
 
@@ -172,6 +201,8 @@
 
 	list_move_tail(&clp->cl_lru, &nn->client_lru);
 	clp->cl_time = ktime_get_boottime_seconds();
+	nfsd4_dec_courtesy_client_count(nn, clp);
+	clp->cl_state = NFSD4_ACTIVE;
 }
 
 static void put_client_renew_locked(struct nfs4_client *clp)
@@ -246,6 +277,7 @@
 	list_for_each_entry(cur, &lo->lo_blocked, nbl_list) {
 		if (fh_match(fh, &cur->nbl_fh)) {
 			list_del_init(&cur->nbl_list);
+			WARN_ON(list_empty(&cur->nbl_lru));
 			list_del_init(&cur->nbl_lru);
 			found = cur;
 			break;
@@ -271,6 +303,7 @@
 			INIT_LIST_HEAD(&nbl->nbl_lru);
 			fh_copy_shallow(&nbl->nbl_fh, fh);
 			locks_init_lock(&nbl->nbl_lock);
+			kref_init(&nbl->nbl_kref);
 			nfsd4_init_cb(&nbl->nbl_cb, lo->lo_owner.so_client,
 					&nfsd4_cb_notify_lock_ops,
 					NFSPROC4_CLNT_CB_NOTIFY_LOCK);
@@ -280,14 +313,23 @@
 }
 
 static void
-free_blocked_lock(struct nfsd4_blocked_lock *nbl)
+free_nbl(struct kref *kref)
 {
-	locks_delete_block(&nbl->nbl_lock);
+	struct nfsd4_blocked_lock *nbl;
+
+	nbl = container_of(kref, struct nfsd4_blocked_lock, nbl_kref);
 	locks_release_private(&nbl->nbl_lock);
 	kfree(nbl);
 }
 
 static void
+free_blocked_lock(struct nfsd4_blocked_lock *nbl)
+{
+	locks_delete_block(&nbl->nbl_lock);
+	kref_put(&nbl->nbl_kref, free_nbl);
+}
+
+static void
 remove_blocked_locks(struct nfs4_lockowner *lo)
 {
 	struct nfs4_client *clp = lo->lo_owner.so_client;
@@ -302,6 +344,7 @@
 					struct nfsd4_blocked_lock,
 					nbl_list);
 		list_del_init(&nbl->nbl_list);
+		WARN_ON(list_empty(&nbl->nbl_lru));
 		list_move(&nbl->nbl_lru, &reaplist);
 	}
 	spin_unlock(&nn->blocked_locks_lock);
@@ -326,6 +369,8 @@
 static int
 nfsd4_cb_notify_lock_done(struct nfsd4_callback *cb, struct rpc_task *task)
 {
+	trace_nfsd_cb_notify_lock_done(&zero_stateid, task);
+
 	/*
 	 * Since this is just an optimization, we don't try very hard if it
 	 * turns out not to succeed. We'll requeue it on NFS4ERR_DELAY, and
@@ -360,11 +405,13 @@
  * st_{access,deny}_bmap field of the stateid, in order to track not
  * only what share bits are currently in force, but also what
  * combinations of share bits previous opens have used.  This allows us
- * to enforce the recommendation of rfc 3530 14.2.19 that the server
- * return an error if the client attempt to downgrade to a combination
- * of share bits not explicable by closing some of its previous opens.
+ * to enforce the recommendation in
+ * https://datatracker.ietf.org/doc/html/rfc7530#section-16.19.4 that
+ * the server return an error if the client attempt to downgrade to a
+ * combination of share bits not explicable by closing some of its
+ * previous opens.
  *
- * XXX: This enforcement is actually incomplete, since we don't keep
+ * This enforcement is arguably incomplete, since we don't keep
  * track of access/deny bit combinations; so, e.g., we allow:
  *
  *	OPEN allow read, deny write
@@ -372,6 +419,10 @@
  *	DOWNGRADE allow read, deny none
  *
  * which we should reject.
+ *
+ * But you could also argue that our current code is already overkill,
+ * since it only exists to return NFS4ERR_INVAL on incorrect client
+ * behavior.
  */
 static unsigned int
 bmap_to_share_mode(unsigned long bmap)
@@ -540,11 +591,8 @@
 void
 put_nfs4_file(struct nfs4_file *fi)
 {
-	might_lock(&state_lock);
-
-	if (refcount_dec_and_lock(&fi->fi_ref, &state_lock)) {
-		hlist_del_rcu(&fi->fi_hash);
-		spin_unlock(&state_lock);
+	if (refcount_dec_and_test(&fi->fi_ref)) {
+		nfsd4_file_hash_remove(fi);
 		WARN_ON_ONCE(!list_empty(&fi->fi_clnt_odstate));
 		WARN_ON_ONCE(!list_empty(&fi->fi_delegations));
 		call_rcu(&fi->fi_rcu, nfsd4_free_file_rcu);
@@ -554,9 +602,7 @@
 static struct nfsd_file *
 __nfs4_get_fd(struct nfs4_file *f, int oflag)
 {
-	if (f->fi_fds[oflag])
-		return nfsd_file_get(f->fi_fds[oflag]);
-	return NULL;
+	return nfsd_file_get(f->fi_fds[oflag]);
 }
 
 static struct nfsd_file *
@@ -627,15 +673,26 @@
 	return ret;
 }
 
-static struct nfsd_file *find_deleg_file(struct nfs4_file *f)
+static struct nfsd_file *find_any_file_locked(struct nfs4_file *f)
+{
+	lockdep_assert_held(&f->fi_lock);
+
+	if (f->fi_fds[O_RDWR])
+		return f->fi_fds[O_RDWR];
+	if (f->fi_fds[O_WRONLY])
+		return f->fi_fds[O_WRONLY];
+	if (f->fi_fds[O_RDONLY])
+		return f->fi_fds[O_RDONLY];
+	return NULL;
+}
+
+static struct nfsd_file *find_deleg_file_locked(struct nfs4_file *f)
 {
-	struct nfsd_file *ret = NULL;
+	lockdep_assert_held(&f->fi_lock);
 
-	spin_lock(&f->fi_lock);
 	if (f->fi_deleg_file)
-		ret = nfsd_file_get(f->fi_deleg_file);
-	spin_unlock(&f->fi_lock);
-	return ret;
+		return f->fi_deleg_file;
+	return NULL;
 }
 
 static atomic_long_t num_delegations;
@@ -658,20 +715,72 @@
 	return ret & OWNER_HASH_MASK;
 }
 
-/* hash table for nfs4_file */
-#define FILE_HASH_BITS                   8
-#define FILE_HASH_SIZE                  (1 << FILE_HASH_BITS)
+static struct rhltable nfs4_file_rhltable ____cacheline_aligned_in_smp;
+
+static const struct rhashtable_params nfs4_file_rhash_params = {
+	.key_len		= sizeof_field(struct nfs4_file, fi_inode),
+	.key_offset		= offsetof(struct nfs4_file, fi_inode),
+	.head_offset		= offsetof(struct nfs4_file, fi_rlist),
+
+	/*
+	 * Start with a single page hash table to reduce resizing churn
+	 * on light workloads.
+	 */
+	.min_size		= 256,
+	.automatic_shrinking	= true,
+};
 
-static unsigned int file_hashval(struct svc_fh *fh)
+/*
+ * Check if courtesy clients have conflicting access and resolve it if possible
+ *
+ * access:  is op_share_access if share_access is true.
+ *	    Check if access mode, op_share_access, would conflict with
+ *	    the current deny mode of the file 'fp'.
+ * access:  is op_share_deny if share_access is false.
+ *	    Check if the deny mode, op_share_deny, would conflict with
+ *	    current access of the file 'fp'.
+ * stp:     skip checking this entry.
+ * new_stp: normal open, not open upgrade.
+ *
+ * Function returns:
+ *	false - access/deny mode conflict with normal client.
+ *	true  - no conflict or conflict with courtesy client(s) is resolved.
+ */
+static bool
+nfs4_resolve_deny_conflicts_locked(struct nfs4_file *fp, bool new_stp,
+		struct nfs4_ol_stateid *stp, u32 access, bool share_access)
 {
-	struct inode *inode = d_inode(fh->fh_dentry);
+	struct nfs4_ol_stateid *st;
+	bool resolvable = true;
+	unsigned char bmap;
+	struct nfsd_net *nn;
+	struct nfs4_client *clp;
 
-	/* XXX: why not (here & in file cache) use inode? */
-	return (unsigned int)hash_long(inode->i_ino, FILE_HASH_BITS);
+	lockdep_assert_held(&fp->fi_lock);
+	list_for_each_entry(st, &fp->fi_stateids, st_perfile) {
+		/* ignore lock stateid */
+		if (st->st_openstp)
+			continue;
+		if (st == stp && new_stp)
+			continue;
+		/* check file access against deny mode or vice versa */
+		bmap = share_access ? st->st_deny_bmap : st->st_access_bmap;
+		if (!(access & bmap_to_share_mode(bmap)))
+			continue;
+		clp = st->st_stid.sc_client;
+		if (try_to_expire_client(clp))
+			continue;
+		resolvable = false;
+		break;
+	}
+	if (resolvable) {
+		clp = stp->st_stid.sc_client;
+		nn = net_generic(clp->net, nfsd_net_id);
+		mod_delayed_work(laundry_wq, &nn->laundromat_work, 0);
+	}
+	return resolvable;
 }
 
-static struct hlist_head file_hashtbl[FILE_HASH_SIZE];
-
 static void
 __nfs4_file_get_access(struct nfs4_file *fp, u32 access)
 {
@@ -875,23 +984,23 @@
  * Create a unique stateid_t to represent each COPY.
  */
 static int nfs4_init_cp_state(struct nfsd_net *nn, copy_stateid_t *stid,
-			      unsigned char sc_type)
+			      unsigned char cs_type)
 {
 	int new_id;
 
-	stid->stid.si_opaque.so_clid.cl_boot = (u32)nn->boot_time;
-	stid->stid.si_opaque.so_clid.cl_id = nn->s2s_cp_cl_id;
-	stid->sc_type = sc_type;
+	stid->cs_stid.si_opaque.so_clid.cl_boot = (u32)nn->boot_time;
+	stid->cs_stid.si_opaque.so_clid.cl_id = nn->s2s_cp_cl_id;
 
 	idr_preload(GFP_KERNEL);
 	spin_lock(&nn->s2s_cp_lock);
 	new_id = idr_alloc_cyclic(&nn->s2s_cp_stateids, stid, 0, 0, GFP_NOWAIT);
-	stid->stid.si_opaque.so_id = new_id;
-	stid->stid.si_generation = 1;
+	stid->cs_stid.si_opaque.so_id = new_id;
+	stid->cs_stid.si_generation = 1;
 	spin_unlock(&nn->s2s_cp_lock);
 	idr_preload_end();
 	if (new_id < 0)
 		return 0;
+	stid->cs_type = cs_type;
 	return 1;
 }
 
@@ -909,7 +1018,7 @@
 	if (!cps)
 		return NULL;
 	cps->cpntf_time = ktime_get_boottime_seconds();
-	refcount_set(&cps->cp_stateid.sc_count, 1);
+	refcount_set(&cps->cp_stateid.cs_count, 1);
 	if (!nfs4_init_cp_state(nn, &cps->cp_stateid, NFS4_COPYNOTIFY_STID))
 		goto out_free;
 	spin_lock(&nn->s2s_cp_lock);
@@ -925,11 +1034,12 @@
 {
 	struct nfsd_net *nn;
 
-	WARN_ON_ONCE(copy->cp_stateid.sc_type != NFS4_COPY_STID);
+	if (copy->cp_stateid.cs_type != NFS4_COPY_STID)
+		return;
 	nn = net_generic(copy->cp_clp->net, nfsd_net_id);
 	spin_lock(&nn->s2s_cp_lock);
 	idr_remove(&nn->s2s_cp_stateids,
-		   copy->cp_stateid.stid.si_opaque.so_id);
+		   copy->cp_stateid.cs_stid.si_opaque.so_id);
 	spin_unlock(&nn->s2s_cp_lock);
 }
 
@@ -959,8 +1069,20 @@
 	return openlockstateid(stid);
 }
 
+/*
+ * As the sc_free callback of deleg, this may be called by nfs4_put_stid
+ * in nfsd_break_one_deleg.
+ * Considering nfsd_break_one_deleg is called with the flc->flc_lock held,
+ * this function mustn't ever sleep.
+ */
 static void nfs4_free_deleg(struct nfs4_stid *stid)
 {
+	struct nfs4_delegation *dp = delegstateid(stid);
+
+	WARN_ON_ONCE(!list_empty(&stid->sc_cp_list));
+	WARN_ON_ONCE(!list_empty(&dp->dl_perfile));
+	WARN_ON_ONCE(!list_empty(&dp->dl_perclnt));
+	WARN_ON_ONCE(!list_empty(&dp->dl_recall_lru));
 	kmem_cache_free(deleg_slab, stid);
 	atomic_long_dec(&num_delegations);
 }
@@ -974,7 +1096,8 @@
  * When a delegation is recalled, the filehandle is stored in the "new"
  * filter.
  * Every 30 seconds we swap the filters and clear the "new" one,
- * unless both are empty of course.
+ * unless both are empty of course.  This results in delegations for a
+ * given filehandle being blocked for between 30 and 60 seconds.
  *
  * Each filter is 256 bits.  We hash the filehandle to 32bit and use the
  * low 3 bytes as hash-table indices.
@@ -1003,14 +1126,14 @@
 		if (ktime_get_seconds() - bd->swap_time > 30) {
 			bd->entries -= bd->old_entries;
 			bd->old_entries = bd->entries;
+			bd->new = 1-bd->new;
 			memset(bd->set[bd->new], 0,
 			       sizeof(bd->set[0]));
-			bd->new = 1-bd->new;
 			bd->swap_time = ktime_get_seconds();
 		}
 		spin_unlock(&blocked_delegations_lock);
 	}
-	hash = jhash(&fh->fh_base, fh->fh_size, 0);
+	hash = jhash(&fh->fh_raw, fh->fh_size, 0);
 	if (test_bit(hash&255, bd->set[0]) &&
 	    test_bit((hash>>8)&255, bd->set[0]) &&
 	    test_bit((hash>>16)&255, bd->set[0]))
@@ -1029,7 +1152,7 @@
 	u32 hash;
 	struct bloom_pair *bd = &blocked_delegations;
 
-	hash = jhash(&fh->fh_base, fh->fh_size, 0);
+	hash = jhash(&fh->fh_raw, fh->fh_size, 0);
 
 	spin_lock(&blocked_delegations_lock);
 	__set_bit(hash&255, bd->set[bd->new]);
@@ -1043,7 +1166,6 @@
 
 static struct nfs4_delegation *
 alloc_init_deleg(struct nfs4_client *clp, struct nfs4_file *fp,
-		 struct svc_fh *current_fh,
 		 struct nfs4_clnt_odstate *odstate)
 {
 	struct nfs4_delegation *dp;
@@ -1053,7 +1175,7 @@
 	n = atomic_long_inc_return(&num_delegations);
 	if (n < 0 || n > max_delegations)
 		goto out_dec;
-	if (delegation_blocked(&current_fh->fh_handle))
+	if (delegation_blocked(&fp->fi_fhandle))
 		goto out_dec;
 	dp = delegstateid(nfs4_alloc_stid(clp, deleg_slab, nfs4_free_deleg));
 	if (dp == NULL)
@@ -1072,6 +1194,7 @@
 	get_clnt_odstate(odstate);
 	dp->dl_type = NFS4_OPEN_DELEGATE_READ;
 	dp->dl_retries = 1;
+	dp->dl_recalled = false;
 	nfsd4_init_cb(&dp->dl_recall, dp->dl_stid.sc_client,
 		      &nfsd4_cb_recall_ops, NFSPROC4_CLNT_CB_RECALL);
 	get_nfs4_file(fp);
@@ -1207,6 +1330,11 @@
 	return 0;
 }
 
+static bool delegation_hashed(struct nfs4_delegation *dp)
+{
+	return !(list_empty(&dp->dl_perfile));
+}
+
 static bool
 unhash_delegation_locked(struct nfs4_delegation *dp)
 {
@@ -1214,7 +1342,7 @@
 
 	lockdep_assert_held(&state_lock);
 
-	if (list_empty(&dp->dl_perfile))
+	if (!delegation_hashed(dp))
 		return false;
 
 	dp->dl_stid.sc_type = NFS4_CLOSED_DELEG_STID;
@@ -1245,10 +1373,12 @@
 
 	WARN_ON(!list_empty(&dp->dl_recall_lru));
 
+	trace_nfsd_stid_revoke(&dp->dl_stid);
+
 	if (clp->cl_minorversion) {
+		spin_lock(&clp->cl_lock);
 		dp->dl_stid.sc_type = NFS4_REVOKED_DELEG_STID;
 		refcount_inc(&dp->dl_stid.sc_count);
-		spin_lock(&clp->cl_lock);
 		list_add(&dp->dl_recall_lru, &clp->cl_revoked);
 		spin_unlock(&clp->cl_lock);
 	}
@@ -1369,6 +1499,7 @@
 	release_all_access(stp);
 	if (stp->st_stateowner)
 		nfs4_put_stateowner(stp->st_stateowner);
+	WARN_ON(!list_empty(&stid->sc_cp_list));
 	kmem_cache_free(stateid_slab, stid);
 }
 
@@ -1503,6 +1634,14 @@
 	free_ol_stateid_reaplist(&reaplist);
 }
 
+static bool nfs4_openowner_unhashed(struct nfs4_openowner *oo)
+{
+	lockdep_assert_held(&oo->oo_owner.so_client->cl_lock);
+
+	return list_empty(&oo->oo_owner.so_strhash) &&
+		list_empty(&oo->oo_perclient);
+}
+
 static void unhash_openowner_locked(struct nfs4_openowner *oo)
 {
 	struct nfs4_client *clp = oo->oo_owner.so_client;
@@ -1708,13 +1847,12 @@
 	int numslots = fattrs->maxreqs;
 	int slotsize = slot_bytes(fattrs);
 	struct nfsd4_session *new;
-	int mem, i;
+	int i;
 
-	BUILD_BUG_ON(NFSD_MAX_SLOTS_PER_SESSION * sizeof(struct nfsd4_slot *)
-			+ sizeof(struct nfsd4_session) > PAGE_SIZE);
-	mem = numslots * sizeof(struct nfsd4_slot *);
+	BUILD_BUG_ON(struct_size(new, se_slots, NFSD_MAX_SLOTS_PER_SESSION)
+		     > PAGE_SIZE);
 
-	new = kzalloc(sizeof(*new) + mem, GFP_KERNEL);
+	new = kzalloc(struct_size(new, se_slots, numslots), GFP_KERNEL);
 	if (!new)
 		return NULL;
 	/* allocate each struct nfsd4_slot and data cache in one piece */
@@ -1959,11 +2097,16 @@
  * This type of memory management is somewhat inefficient, but we use it
  * anyway since SETCLIENTID is not a common operation.
  */
-static struct nfs4_client *alloc_client(struct xdr_netobj name)
+static struct nfs4_client *alloc_client(struct xdr_netobj name,
+				struct nfsd_net *nn)
 {
 	struct nfs4_client *clp;
 	int i;
 
+	if (atomic_read(&nn->nfs4_client_count) >= nn->nfs4_max_clients) {
+		mod_delayed_work(laundry_wq, &nn->laundromat_work, 0);
+		return NULL;
+	}
 	clp = kmem_cache_zalloc(client_slab, GFP_KERNEL);
 	if (clp == NULL)
 		return NULL;
@@ -1981,6 +2124,9 @@
 	idr_init(&clp->cl_stateids);
 	atomic_set(&clp->cl_rpc_users, 0);
 	clp->cl_cb_state = NFSD4_CB_UNKNOWN;
+	clp->cl_state = NFSD4_ACTIVE;
+	atomic_inc(&nn->nfs4_client_count);
+	atomic_set(&clp->cl_delegs_in_recall, 0);
 	INIT_LIST_HEAD(&clp->cl_idhash);
 	INIT_LIST_HEAD(&clp->cl_openowners);
 	INIT_LIST_HEAD(&clp->cl_delegations);
@@ -2012,6 +2158,7 @@
 	kfree(clp->cl_nii_domain.data);
 	kfree(clp->cl_nii_name.data);
 	idr_destroy(&clp->cl_stateids);
+	kfree(clp->cl_ra);
 	kmem_cache_free(client_slab, clp);
 }
 
@@ -2087,6 +2234,7 @@
 static void
 __destroy_client(struct nfs4_client *clp)
 {
+	struct nfsd_net *nn = net_generic(clp->net, nfsd_net_id);
 	int i;
 	struct nfs4_openowner *oo;
 	struct nfs4_delegation *dp;
@@ -2130,6 +2278,8 @@
 	nfsd4_shutdown_callback(clp);
 	if (clp->cl_cb_conn.cb_xprt)
 		svc_xprt_put(clp->cl_cb_conn.cb_xprt);
+	atomic_add_unless(&nn->nfs4_client_count, -1, 0);
+	nfsd4_dec_courtesy_client_count(nn, clp);
 	free_client(clp);
 	wake_up_all(&expiry_wq);
 }
@@ -2375,7 +2525,7 @@
 
 static int client_info_show(struct seq_file *m, void *v)
 {
-	struct inode *inode = m->private;
+	struct inode *inode = file_inode(m->file);
 	struct nfs4_client *clp;
 	u64 clid;
 
@@ -2385,10 +2535,17 @@
 	memcpy(&clid, &clp->cl_clientid, sizeof(clid));
 	seq_printf(m, "clientid: 0x%llx\n", clid);
 	seq_printf(m, "address: \"%pISpc\"\n", (struct sockaddr *)&clp->cl_addr);
-	if (test_bit(NFSD4_CLIENT_CONFIRMED, &clp->cl_flags))
+
+	if (clp->cl_state == NFSD4_COURTESY)
+		seq_puts(m, "status: courtesy\n");
+	else if (clp->cl_state == NFSD4_EXPIRABLE)
+		seq_puts(m, "status: expirable\n");
+	else if (test_bit(NFSD4_CLIENT_CONFIRMED, &clp->cl_flags))
 		seq_puts(m, "status: confirmed\n");
 	else
 		seq_puts(m, "status: unconfirmed\n");
+	seq_printf(m, "seconds from last renew: %lld\n",
+		ktime_get_boottime_seconds() - clp->cl_time);
 	seq_printf(m, "name: ");
 	seq_quote_mem(m, clp->cl_name.data, clp->cl_name.len);
 	seq_printf(m, "\nminor version: %d\n", clp->cl_minorversion);
@@ -2408,17 +2565,7 @@
 	return 0;
 }
 
-static int client_info_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, client_info_show, inode);
-}
-
-static const struct file_operations client_info_fops = {
-	.open		= client_info_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(client_info);
 
 static void *states_start(struct seq_file *s, loff_t *pos)
 	__acquires(&clp->cl_lock)
@@ -2461,7 +2608,7 @@
 
 static void nfs4_show_superblock(struct seq_file *s, struct nfsd_file *f)
 {
-	struct inode *inode = f->nf_inode;
+	struct inode *inode = file_inode(f->nf_file);
 
 	seq_printf(s, "superblock: \"%02x:%02x:%ld\"",
 					MAJOR(inode->i_sb->s_dev),
@@ -2494,9 +2641,11 @@
 	ols = openlockstateid(st);
 	oo = ols->st_stateowner;
 	nf = st->sc_file;
-	file = find_any_file(nf);
+
+	spin_lock(&nf->fi_lock);
+	file = find_any_file_locked(nf);
 	if (!file)
-		return 0;
+		goto out;
 
 	seq_printf(s, "- ");
 	nfs4_show_stateid(s, &st->sc_stateid);
@@ -2518,8 +2667,8 @@
 	seq_printf(s, ", ");
 	nfs4_show_owner(s, oo);
 	seq_printf(s, " }\n");
-	nfsd_file_put(file);
-
+out:
+	spin_unlock(&nf->fi_lock);
 	return 0;
 }
 
@@ -2533,9 +2682,10 @@
 	ols = openlockstateid(st);
 	oo = ols->st_stateowner;
 	nf = st->sc_file;
-	file = find_any_file(nf);
+	spin_lock(&nf->fi_lock);
+	file = find_any_file_locked(nf);
 	if (!file)
-		return 0;
+		goto out;
 
 	seq_printf(s, "- ");
 	nfs4_show_stateid(s, &st->sc_stateid);
@@ -2555,8 +2705,8 @@
 	seq_printf(s, ", ");
 	nfs4_show_owner(s, oo);
 	seq_printf(s, " }\n");
-	nfsd_file_put(file);
-
+out:
+	spin_unlock(&nf->fi_lock);
 	return 0;
 }
 
@@ -2568,9 +2718,10 @@
 
 	ds = delegstateid(st);
 	nf = st->sc_file;
-	file = find_deleg_file(nf);
+	spin_lock(&nf->fi_lock);
+	file = find_deleg_file_locked(nf);
 	if (!file)
-		return 0;
+		goto out;
 
 	seq_printf(s, "- ");
 	nfs4_show_stateid(s, &st->sc_stateid);
@@ -2586,8 +2737,8 @@
 	seq_printf(s, ", ");
 	nfs4_show_fname(s, file);
 	seq_printf(s, " }\n");
-	nfsd_file_put(file);
-
+out:
+	spin_unlock(&nf->fi_lock);
 	return 0;
 }
 
@@ -2664,7 +2815,7 @@
 
 	/* XXX: alternatively, we could get/drop in seq start/stop */
 	drop_client(clp);
-	return 0;
+	return seq_release(inode, file);
 }
 
 static const struct file_operations client_states_fops = {
@@ -2735,6 +2886,34 @@
 	[3] = {""},
 };
 
+static int
+nfsd4_cb_recall_any_done(struct nfsd4_callback *cb,
+				struct rpc_task *task)
+{
+	trace_nfsd_cb_recall_any_done(cb, task);
+	switch (task->tk_status) {
+	case -NFS4ERR_DELAY:
+		rpc_delay(task, 2 * HZ);
+		return 0;
+	default:
+		return 1;
+	}
+}
+
+static void
+nfsd4_cb_recall_any_release(struct nfsd4_callback *cb)
+{
+	struct nfs4_client *clp = cb->cb_clp;
+
+	clear_bit(NFSD4_CLIENT_CB_RECALL_ANY, &clp->cl_flags);
+	drop_client(clp);
+}
+
+static const struct nfsd4_callback_ops nfsd4_cb_recall_any_ops = {
+	.done		= nfsd4_cb_recall_any_done,
+	.release	= nfsd4_cb_recall_any_release,
+};
+
 static struct nfs4_client *create_client(struct xdr_netobj name,
 		struct svc_rqst *rqstp, nfs4_verifier *verf)
 {
@@ -2745,7 +2924,7 @@
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 	struct dentry *dentries[ARRAY_SIZE(client_files)];
 
-	clp = alloc_client(name);
+	clp = alloc_client(name, nn);
 	if (clp == NULL)
 		return NULL;
 
@@ -2772,6 +2951,14 @@
 		free_client(clp);
 		return NULL;
 	}
+	clp->cl_ra = kzalloc(sizeof(*clp->cl_ra), GFP_KERNEL);
+	if (!clp->cl_ra) {
+		free_client(clp);
+		return NULL;
+	}
+	clp->cl_ra_time = 0;
+	nfsd4_init_cb(&clp->cl_ra->ra_cb, clp, &nfsd4_cb_recall_any_ops,
+			NFSPROC4_CLNT_CB_RECALL_ANY);
 	return clp;
 }
 
@@ -4107,8 +4294,10 @@
 			status = nfserr_clid_inuse;
 			if (client_has_state(old)
 					&& !same_creds(&unconf->cl_cred,
-							&old->cl_cred))
+							&old->cl_cred)) {
+				old = NULL;
 				goto out;
+			}
 			status = mark_client_expired_locked(old);
 			if (status) {
 				old = NULL;
@@ -4139,11 +4328,9 @@
 }
 
 /* OPEN Share state helper functions */
-static void nfsd4_init_file(struct svc_fh *fh, unsigned int hashval,
-				struct nfs4_file *fp)
-{
-	lockdep_assert_held(&state_lock);
 
+static void nfsd4_file_init(const struct svc_fh *fh, struct nfs4_file *fp)
+{
 	refcount_set(&fp->fi_ref, 1);
 	spin_lock_init(&fp->fi_lock);
 	INIT_LIST_HEAD(&fp->fi_stateids);
@@ -4161,7 +4348,6 @@
 	INIT_LIST_HEAD(&fp->fi_lo_states);
 	atomic_set(&fp->fi_lo_recalls, 0);
 #endif
-	hlist_add_head_rcu(&fp->fi_hash, &file_hashtbl[hashval]);
 }
 
 void
@@ -4225,6 +4411,54 @@
 	return -ENOMEM;
 }
 
+static unsigned long
+nfsd4_state_shrinker_count(struct shrinker *shrink, struct shrink_control *sc)
+{
+	int count;
+	struct nfsd_net *nn = container_of(shrink,
+			struct nfsd_net, nfsd_client_shrinker);
+
+	count = atomic_read(&nn->nfsd_courtesy_clients);
+	if (!count)
+		count = atomic_long_read(&num_delegations);
+	if (count)
+		queue_work(laundry_wq, &nn->nfsd_shrinker_work);
+	return (unsigned long)count;
+}
+
+static unsigned long
+nfsd4_state_shrinker_scan(struct shrinker *shrink, struct shrink_control *sc)
+{
+	return SHRINK_STOP;
+}
+
+void
+nfsd4_init_leases_net(struct nfsd_net *nn)
+{
+	struct sysinfo si;
+	u64 max_clients;
+
+	nn->nfsd4_lease = 90;	/* default lease time */
+	nn->nfsd4_grace = 90;
+	nn->somebody_reclaimed = false;
+	nn->track_reclaim_completes = false;
+	nn->clverifier_counter = prandom_u32();
+	nn->clientid_base = prandom_u32();
+	nn->clientid_counter = nn->clientid_base + 1;
+	nn->s2s_cp_cl_id = nn->clientid_counter++;
+
+	atomic_set(&nn->nfs4_client_count, 0);
+	si_meminfo(&si);
+	max_clients = (u64)si.totalram * si.mem_unit / (1024 * 1024 * 1024);
+	max_clients *= NFS4_CLIENTS_PER_GB;
+	nn->nfs4_max_clients = max_t(int, max_clients, NFS4_CLIENTS_PER_GB);
+
+	atomic_set(&nn->nfsd_courtesy_clients, 0);
+	nn->nfsd_client_shrinker.scan_objects = nfsd4_state_shrinker_scan;
+	nn->nfsd_client_shrinker.count_objects = nfsd4_state_shrinker_count;
+	nn->nfsd_client_shrinker.seeks = DEFAULT_SEEKS;
+}
+
 static void init_nfs4_replay(struct nfs4_replay *rp)
 {
 	rp->rp_status = nfserr_serverfault;
@@ -4418,6 +4652,12 @@
 	spin_lock(&oo->oo_owner.so_client->cl_lock);
 	spin_lock(&fp->fi_lock);
 
+	if (nfs4_openowner_unhashed(oo)) {
+		mutex_unlock(&stp->st_mutex);
+		stp = NULL;
+		goto out_unlock;
+	}
+
 	retstp = nfsd4_find_existing_open(fp, open);
 	if (retstp)
 		goto out_unlock;
@@ -4493,71 +4733,80 @@
 		nfs4_put_stid(&last->st_stid);
 }
 
-/* search file_hashtbl[] for file */
-static struct nfs4_file *
-find_file_locked(struct svc_fh *fh, unsigned int hashval)
+static noinline_for_stack struct nfs4_file *
+nfsd4_file_hash_lookup(const struct svc_fh *fhp)
 {
-	struct nfs4_file *fp;
+	struct inode *inode = d_inode(fhp->fh_dentry);
+	struct rhlist_head *tmp, *list;
+	struct nfs4_file *fi;
 
-	hlist_for_each_entry_rcu(fp, &file_hashtbl[hashval], fi_hash,
-				lockdep_is_held(&state_lock)) {
-		if (fh_match(&fp->fi_fhandle, &fh->fh_handle)) {
-			if (refcount_inc_not_zero(&fp->fi_ref))
-				return fp;
+	rcu_read_lock();
+	list = rhltable_lookup(&nfs4_file_rhltable, &inode,
+			       nfs4_file_rhash_params);
+	rhl_for_each_entry_rcu(fi, tmp, list, fi_rlist) {
+		if (fh_match(&fi->fi_fhandle, &fhp->fh_handle)) {
+			if (refcount_inc_not_zero(&fi->fi_ref)) {
+				rcu_read_unlock();
+				return fi;
+			}
 		}
 	}
+	rcu_read_unlock();
 	return NULL;
 }
 
-static struct nfs4_file *insert_file(struct nfs4_file *new, struct svc_fh *fh,
-				     unsigned int hashval)
+/*
+ * On hash insertion, identify entries with the same inode but
+ * distinct filehandles. They will all be on the list returned
+ * by rhltable_lookup().
+ *
+ * inode->i_lock prevents racing insertions from adding an entry
+ * for the same inode/fhp pair twice.
+ */
+static noinline_for_stack struct nfs4_file *
+nfsd4_file_hash_insert(struct nfs4_file *new, const struct svc_fh *fhp)
 {
-	struct nfs4_file *fp;
+	struct inode *inode = d_inode(fhp->fh_dentry);
+	struct rhlist_head *tmp, *list;
 	struct nfs4_file *ret = NULL;
 	bool alias_found = false;
+	struct nfs4_file *fi;
+	int err;
 
-	spin_lock(&state_lock);
-	hlist_for_each_entry_rcu(fp, &file_hashtbl[hashval], fi_hash,
-				 lockdep_is_held(&state_lock)) {
-		if (fh_match(&fp->fi_fhandle, &fh->fh_handle)) {
-			if (refcount_inc_not_zero(&fp->fi_ref))
-				ret = fp;
-		} else if (d_inode(fh->fh_dentry) == fp->fi_inode)
-			fp->fi_aliased = alias_found = true;
-	}
-	if (likely(ret == NULL)) {
-		nfsd4_init_file(fh, hashval, new);
-		new->fi_aliased = alias_found;
-		ret = new;
+	rcu_read_lock();
+	spin_lock(&inode->i_lock);
+
+	list = rhltable_lookup(&nfs4_file_rhltable, &inode,
+			       nfs4_file_rhash_params);
+	rhl_for_each_entry_rcu(fi, tmp, list, fi_rlist) {
+		if (fh_match(&fi->fi_fhandle, &fhp->fh_handle)) {
+			if (refcount_inc_not_zero(&fi->fi_ref))
+				ret = fi;
+		} else
+			fi->fi_aliased = alias_found = true;
 	}
-	spin_unlock(&state_lock);
-	return ret;
-}
+	if (ret)
+		goto out_unlock;
 
-static struct nfs4_file * find_file(struct svc_fh *fh)
-{
-	struct nfs4_file *fp;
-	unsigned int hashval = file_hashval(fh);
+	nfsd4_file_init(fhp, new);
+	err = rhltable_insert(&nfs4_file_rhltable, &new->fi_rlist,
+			      nfs4_file_rhash_params);
+	if (err)
+		goto out_unlock;
 
-	rcu_read_lock();
-	fp = find_file_locked(fh, hashval);
+	new->fi_aliased = alias_found;
+	ret = new;
+
+out_unlock:
+	spin_unlock(&inode->i_lock);
 	rcu_read_unlock();
-	return fp;
+	return ret;
 }
 
-static struct nfs4_file *
-find_or_add_file(struct nfs4_file *new, struct svc_fh *fh)
+static noinline_for_stack void nfsd4_file_hash_remove(struct nfs4_file *fi)
 {
-	struct nfs4_file *fp;
-	unsigned int hashval = file_hashval(fh);
-
-	rcu_read_lock();
-	fp = find_file_locked(fh, hashval);
-	rcu_read_unlock();
-	if (fp)
-		return fp;
-
-	return insert_file(new, fh, hashval);
+	rhltable_remove(&nfs4_file_rhltable, &fi->fi_rlist,
+			nfs4_file_rhash_params);
 }
 
 /*
@@ -4570,9 +4819,10 @@
 	struct nfs4_file *fp;
 	__be32 ret = nfs_ok;
 
-	fp = find_file(current_fh);
+	fp = nfsd4_file_hash_lookup(current_fh);
 	if (!fp)
 		return ret;
+
 	/* Check for conflicting share reservations */
 	spin_lock(&fp->fi_lock);
 	if (fp->fi_share_deny & deny_type)
@@ -4582,6 +4832,35 @@
 	return ret;
 }
 
+static bool nfsd4_deleg_present(const struct inode *inode)
+{
+	struct file_lock_context *ctx = locks_inode_context(inode);
+
+	return ctx && !list_empty_careful(&ctx->flc_lease);
+}
+
+/**
+ * nfsd_wait_for_delegreturn - wait for delegations to be returned
+ * @rqstp: the RPC transaction being executed
+ * @inode: in-core inode of the file being waited for
+ *
+ * The timeout prevents deadlock if all nfsd threads happen to be
+ * tied up waiting for returning delegations.
+ *
+ * Return values:
+ *   %true: delegation was returned
+ *   %false: timed out waiting for delegreturn
+ */
+bool nfsd_wait_for_delegreturn(struct svc_rqst *rqstp, struct inode *inode)
+{
+	long __maybe_unused timeo;
+
+	timeo = wait_var_event_timeout(inode, !nfsd4_deleg_present(inode),
+				       NFSD_DELEGRETURN_TIMEOUT);
+	trace_nfsd_delegret_wakeup(rqstp, inode, timeo);
+	return timeo > 0;
+}
+
 static void nfsd4_cb_recall_prepare(struct nfsd4_callback *cb)
 {
 	struct nfs4_delegation *dp = cb_to_delegation(cb);
@@ -4598,7 +4877,7 @@
 	 * queued for a lease break. Don't queue it again.
 	 */
 	spin_lock(&state_lock);
-	if (dp->dl_time == 0) {
+	if (delegation_hashed(dp) && dp->dl_time == 0) {
 		dp->dl_time = ktime_get_boottime_seconds();
 		list_add_tail(&dp->dl_recall_lru, &nn->del_recall_lru);
 	}
@@ -4610,6 +4889,8 @@
 {
 	struct nfs4_delegation *dp = cb_to_delegation(cb);
 
+	trace_nfsd_cb_recall_done(&dp->dl_stid.sc_stateid, task);
+
 	if (dp->dl_stid.sc_type == NFS4_CLOSED_DELEG_STID ||
 	    dp->dl_stid.sc_type == NFS4_REVOKED_DELEG_STID)
 	        return 1;
@@ -4651,27 +4932,39 @@
 
 static void nfsd_break_one_deleg(struct nfs4_delegation *dp)
 {
+	bool queued;
 	/*
 	 * We're assuming the state code never drops its reference
 	 * without first removing the lease.  Since we're in this lease
 	 * callback (and since the lease code is serialized by the
-	 * i_lock) we know the server hasn't removed the lease yet, and
+	 * flc_lock) we know the server hasn't removed the lease yet, and
 	 * we know it's safe to take a reference.
 	 */
 	refcount_inc(&dp->dl_stid.sc_count);
-	nfsd4_run_cb(&dp->dl_recall);
+	queued = nfsd4_run_cb(&dp->dl_recall);
+	WARN_ON_ONCE(!queued);
+	if (!queued)
+		nfs4_put_stid(&dp->dl_stid);
 }
 
-/* Called from break_lease() with i_lock held. */
+/* Called from break_lease() with flc_lock held. */
 static bool
 nfsd_break_deleg_cb(struct file_lock *fl)
 {
-	bool ret = false;
 	struct nfs4_delegation *dp = (struct nfs4_delegation *)fl->fl_owner;
 	struct nfs4_file *fp = dp->dl_stid.sc_file;
+	struct nfs4_client *clp = dp->dl_stid.sc_client;
+	struct nfsd_net *nn;
 
 	trace_nfsd_cb_recall(&dp->dl_stid);
 
+	dp->dl_recalled = true;
+	atomic_inc(&clp->cl_delegs_in_recall);
+	if (try_to_expire_client(clp)) {
+		nn = net_generic(clp->net, nfsd_net_id);
+		mod_delayed_work(laundry_wq, &nn->laundromat_work, 0);
+	}
+
 	/*
 	 * We don't want the locks code to timeout the lease for us;
 	 * we'll remove it ourself if a delegation isn't returned
@@ -4679,13 +4972,19 @@
 	 */
 	fl->fl_break_time = 0;
 
-	spin_lock(&fp->fi_lock);
 	fp->fi_had_conflict = true;
 	nfsd_break_one_deleg(dp);
-	spin_unlock(&fp->fi_lock);
-	return ret;
+	return false;
 }
 
+/**
+ * nfsd_breaker_owns_lease - Check if lease conflict was resolved
+ * @fl: Lock state to check
+ *
+ * Return values:
+ *   %true: Lease conflict was resolved
+ *   %false: Lease conflict was not resolved.
+ */
 static bool nfsd_breaker_owns_lease(struct file_lock *fl)
 {
 	struct nfs4_delegation *dl = fl->fl_owner;
@@ -4693,11 +4992,11 @@
 	struct nfs4_client *clp;
 
 	if (!i_am_nfsd())
-		return NULL;
+		return false;
 	rqst = kthread_data(current);
 	/* Note rq_prog == NFS_ACL_PROGRAM is also possible: */
 	if (rqst->rq_prog != NFS_PROGRAM || rqst->rq_vers < 4)
-		return NULL;
+		return false;
 	clp = *(rqst->rq_lease_breaker);
 	return dl->dl_stid.sc_client == clp;
 }
@@ -4706,9 +5005,14 @@
 nfsd_change_deleg_cb(struct file_lock *onlist, int arg,
 		     struct list_head *dispose)
 {
-	if (arg & F_UNLCK)
+	struct nfs4_delegation *dp = (struct nfs4_delegation *)onlist->fl_owner;
+	struct nfs4_client *clp = dp->dl_stid.sc_client;
+
+	if (arg & F_UNLCK) {
+		if (dp->dl_recalled)
+			atomic_dec(&clp->cl_delegs_in_recall);
 		return lease_modify(onlist, arg, dispose);
-	else
+	} else
 		return -EAGAIN;
 }
 
@@ -4905,16 +5209,19 @@
 		.ia_valid = ATTR_SIZE,
 		.ia_size = 0,
 	};
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &iattr,
+	};
 	if (!open->op_truncate)
 		return 0;
 	if (!(open->op_share_access & NFS4_SHARE_ACCESS_WRITE))
 		return nfserr_inval;
-	return nfsd_setattr(rqstp, fh, &iattr, 0, (time64_t)0);
+	return nfsd_setattr(rqstp, fh, &attrs, 0, (time64_t)0);
 }
 
 static __be32 nfs4_get_vfs_file(struct svc_rqst *rqstp, struct nfs4_file *fp,
 		struct svc_fh *cur_fh, struct nfs4_ol_stateid *stp,
-		struct nfsd4_open *open)
+		struct nfsd4_open *open, bool new_stp)
 {
 	struct nfsd_file *nf = NULL;
 	__be32 status;
@@ -4930,6 +5237,13 @@
 	 */
 	status = nfs4_file_check_deny(fp, open->op_share_deny);
 	if (status != nfs_ok) {
+		if (status != nfserr_share_denied) {
+			spin_unlock(&fp->fi_lock);
+			goto out;
+		}
+		if (nfs4_resolve_deny_conflicts_locked(fp, new_stp,
+				stp, open->op_share_deny, false))
+			status = nfserr_jukebox;
 		spin_unlock(&fp->fi_lock);
 		goto out;
 	}
@@ -4937,6 +5251,13 @@
 	/* set access to the file */
 	status = nfs4_file_get_access(fp, open->op_share_access);
 	if (status != nfs_ok) {
+		if (status != nfserr_share_denied) {
+			spin_unlock(&fp->fi_lock);
+			goto out;
+		}
+		if (nfs4_resolve_deny_conflicts_locked(fp, new_stp,
+				stp, open->op_share_access, true))
+			status = nfserr_jukebox;
 		spin_unlock(&fp->fi_lock);
 		goto out;
 	}
@@ -4952,9 +5273,12 @@
 
 	if (!fp->fi_fds[oflag]) {
 		spin_unlock(&fp->fi_lock);
-		status = nfsd_file_acquire(rqstp, cur_fh, access, &nf);
-		if (status)
+
+		status = nfsd_file_acquire_opened(rqstp, cur_fh, access,
+						  open->op_filp, &nf);
+		if (status != nfs_ok)
 			goto out_put_access;
+
 		spin_lock(&fp->fi_lock);
 		if (!fp->fi_fds[oflag]) {
 			fp->fi_fds[oflag] = nf;
@@ -4983,21 +5307,30 @@
 }
 
 static __be32
-nfs4_upgrade_open(struct svc_rqst *rqstp, struct nfs4_file *fp, struct svc_fh *cur_fh, struct nfs4_ol_stateid *stp, struct nfsd4_open *open)
+nfs4_upgrade_open(struct svc_rqst *rqstp, struct nfs4_file *fp,
+		struct svc_fh *cur_fh, struct nfs4_ol_stateid *stp,
+		struct nfsd4_open *open)
 {
 	__be32 status;
 	unsigned char old_deny_bmap = stp->st_deny_bmap;
 
 	if (!test_access(open->op_share_access, stp))
-		return nfs4_get_vfs_file(rqstp, fp, cur_fh, stp, open);
+		return nfs4_get_vfs_file(rqstp, fp, cur_fh, stp, open, false);
 
 	/* test and set deny mode */
 	spin_lock(&fp->fi_lock);
 	status = nfs4_file_check_deny(fp, open->op_share_deny);
-	if (status == nfs_ok) {
+	switch (status) {
+	case nfs_ok:
 		set_deny(open->op_share_deny, stp);
 		fp->fi_share_deny |=
-				(open->op_share_deny & NFS4_SHARE_DENY_BOTH);
+			(open->op_share_deny & NFS4_SHARE_DENY_BOTH);
+		break;
+	case nfserr_share_denied:
+		if (nfs4_resolve_deny_conflicts_locked(fp, false,
+				stp, open->op_share_deny, false))
+			status = nfserr_jukebox;
+		break;
 	}
 	spin_unlock(&fp->fi_lock);
 
@@ -5100,11 +5433,59 @@
 	return 0;
 }
 
+/*
+ * It's possible that between opening the dentry and setting the delegation,
+ * that it has been renamed or unlinked. Redo the lookup to verify that this
+ * hasn't happened.
+ */
+static int
+nfsd4_verify_deleg_dentry(struct nfsd4_open *open, struct nfs4_file *fp,
+			  struct svc_fh *parent)
+{
+	struct svc_export *exp;
+	struct dentry *child;
+	__be32 err;
+
+	err = nfsd_lookup_dentry(open->op_rqstp, parent,
+				 open->op_fname, open->op_fnamelen,
+				 &exp, &child);
+
+	if (err)
+		return -EAGAIN;
+
+	exp_put(exp);
+	dput(child);
+	if (child != file_dentry(fp->fi_deleg_file->nf_file))
+		return -EAGAIN;
+
+	return 0;
+}
+
+/*
+ * We avoid breaking delegations held by a client due to its own activity, but
+ * clearing setuid/setgid bits on a write is an implicit activity and the client
+ * may not notice and continue using the old mode. Avoid giving out a delegation
+ * on setuid/setgid files when the client is requesting an open for write.
+ */
+static int
+nfsd4_verify_setuid_write(struct nfsd4_open *open, struct nfsd_file *nf)
+{
+	struct inode *inode = file_inode(nf->nf_file);
+
+	if ((open->op_share_access & NFS4_SHARE_ACCESS_WRITE) &&
+	    (inode->i_mode & (S_ISUID|S_ISGID)))
+		return -EAGAIN;
+	return 0;
+}
+
 static struct nfs4_delegation *
-nfs4_set_delegation(struct nfs4_client *clp, struct svc_fh *fh,
-		    struct nfs4_file *fp, struct nfs4_clnt_odstate *odstate)
+nfs4_set_delegation(struct nfsd4_open *open, struct nfs4_ol_stateid *stp,
+		    struct svc_fh *parent)
 {
 	int status = 0;
+	struct nfs4_client *clp = stp->st_stid.sc_client;
+	struct nfs4_file *fp = stp->st_stid.sc_file;
+	struct nfs4_clnt_odstate *odstate = stp->st_clnt_odstate;
 	struct nfs4_delegation *dp;
 	struct nfsd_file *nf;
 	struct file_lock *fl;
@@ -5130,6 +5511,8 @@
 	spin_lock(&fp->fi_lock);
 	if (nfs4_delegation_exists(clp, fp))
 		status = -EAGAIN;
+	else if (nfsd4_verify_setuid_write(open, nf))
+		status = -EAGAIN;
 	else if (!fp->fi_deleg_file) {
 		fp->fi_deleg_file = nf;
 		/* increment early to prevent fi_deleg_file from being
@@ -5146,7 +5529,7 @@
 		return ERR_PTR(status);
 
 	status = -ENOMEM;
-	dp = alloc_init_deleg(clp, fp, fh, odstate);
+	dp = alloc_init_deleg(clp, fp, odstate);
 	if (!dp)
 		goto out_delegees;
 
@@ -5159,16 +5542,32 @@
 		locks_free_lock(fl);
 	if (status)
 		goto out_clnt_odstate;
+
+	if (parent) {
+		status = nfsd4_verify_deleg_dentry(open, fp, parent);
+		if (status)
+			goto out_unlock;
+	}
+
 	status = nfsd4_check_conflicting_opens(clp, fp);
 	if (status)
 		goto out_unlock;
 
+	/*
+	 * Now that the deleg is set, check again to ensure that nothing
+	 * raced in and changed the mode while we weren't lookng.
+	 */
+	status = nfsd4_verify_setuid_write(open, fp->fi_deleg_file);
+	if (status)
+		goto out_unlock;
+
+	status = -EAGAIN;
+	if (fp->fi_had_conflict)
+		goto out_unlock;
+
 	spin_lock(&state_lock);
 	spin_lock(&fp->fi_lock);
-	if (fp->fi_had_conflict)
-		status = -EAGAIN;
-	else
-		status = hash_delegation_locked(dp, fp);
+	status = hash_delegation_locked(dp, fp);
 	spin_unlock(&fp->fi_lock);
 	spin_unlock(&state_lock);
 
@@ -5214,12 +5613,13 @@
  * proper support for them.
  */
 static void
-nfs4_open_delegation(struct svc_fh *fh, struct nfsd4_open *open,
-			struct nfs4_ol_stateid *stp)
+nfs4_open_delegation(struct nfsd4_open *open, struct nfs4_ol_stateid *stp,
+		     struct svc_fh *currentfh)
 {
 	struct nfs4_delegation *dp;
 	struct nfs4_openowner *oo = openowner(stp->st_stateowner);
 	struct nfs4_client *clp = stp->st_stid.sc_client;
+	struct svc_fh *parent = NULL;
 	int cb_up;
 	int status = 0;
 
@@ -5233,6 +5633,8 @@
 				goto out_no_deleg;
 			break;
 		case NFS4_OPEN_CLAIM_NULL:
+			parent = currentfh;
+			fallthrough;
 		case NFS4_OPEN_CLAIM_FH:
 			/*
 			 * Let's not give out any delegations till everyone's
@@ -5247,7 +5649,7 @@
 		default:
 			goto out_no_deleg;
 	}
-	dp = nfs4_set_delegation(clp, fh, stp->st_stid.sc_file, stp->st_clnt_odstate);
+	dp = nfs4_set_delegation(open, stp, parent);
 	if (IS_ERR(dp))
 		goto out_no_deleg;
 
@@ -5289,6 +5691,18 @@
 	 */
 }
 
+/**
+ * nfsd4_process_open2 - finish open processing
+ * @rqstp: the RPC transaction being executed
+ * @current_fh: NFSv4 COMPOUND's current filehandle
+ * @open: OPEN arguments
+ *
+ * If successful, (1) truncate the file if open->op_truncate was
+ * set, (2) set open->op_stateid, (3) set open->op_delegation.
+ *
+ * Returns %nfs_ok on success; otherwise an nfs4stat value in
+ * network byte order is returned.
+ */
 __be32
 nfsd4_process_open2(struct svc_rqst *rqstp, struct svc_fh *current_fh, struct nfsd4_open *open)
 {
@@ -5305,7 +5719,9 @@
 	 * and check for delegations in the process of being recalled.
 	 * If not found, create the nfs4_file struct
 	 */
-	fp = find_or_add_file(open->op_file, current_fh);
+	fp = nfsd4_file_hash_insert(open->op_file, current_fh);
+	if (unlikely(!fp))
+		return nfserr_jukebox;
 	if (fp != open->op_file) {
 		status = nfs4_check_deleg(cl, open, &dp);
 		if (status)
@@ -5320,6 +5736,11 @@
 
 	if (!stp) {
 		stp = init_open_stateid(fp, open);
+		if (!stp) {
+			status = nfserr_jukebox;
+			goto out;
+		}
+
 		if (!open->op_stp)
 			new_stp = true;
 	}
@@ -5338,7 +5759,7 @@
 			goto out;
 		}
 	} else {
-		status = nfs4_get_vfs_file(rqstp, fp, current_fh, stp, open);
+		status = nfs4_get_vfs_file(rqstp, fp, current_fh, stp, open, true);
 		if (status) {
 			stp->st_stid.sc_type = NFS4_CLOSED_STID;
 			release_open_stateid(stp);
@@ -5367,7 +5788,7 @@
 	* Attempt to hand out a delegation. No error return, because the
 	* OPEN succeeds even if we fail.
 	*/
-	nfs4_open_delegation(current_fh, open, stp);
+	nfs4_open_delegation(open, stp, &resp->cstate.current_fh);
 nodeleg:
 	status = nfs_ok;
 	trace_nfsd_open(&stp->st_stid.sc_stateid);
@@ -5541,7 +5962,7 @@
 static void nfsd4_ssc_expire_umount(struct nfsd_net *nn)
 {
 	bool do_wakeup = false;
-	struct nfsd4_ssc_umount_item *ni = 0;
+	struct nfsd4_ssc_umount_item *ni = NULL;
 	struct nfsd4_ssc_umount_item *tmp;
 
 	spin_lock(&nn->nfsd_ssc_lock);
@@ -5572,10 +5993,131 @@
 }
 #endif
 
+/* Check if any lock belonging to this lockowner has any blockers */
+static bool
+nfs4_lockowner_has_blockers(struct nfs4_lockowner *lo)
+{
+	struct file_lock_context *ctx;
+	struct nfs4_ol_stateid *stp;
+	struct nfs4_file *nf;
+
+	list_for_each_entry(stp, &lo->lo_owner.so_stateids, st_perstateowner) {
+		nf = stp->st_stid.sc_file;
+		ctx = locks_inode_context(nf->fi_inode);
+		if (!ctx)
+			continue;
+		if (locks_owner_has_blockers(ctx, lo))
+			return true;
+	}
+	return false;
+}
+
+static bool
+nfs4_anylock_blockers(struct nfs4_client *clp)
+{
+	int i;
+	struct nfs4_stateowner *so;
+	struct nfs4_lockowner *lo;
+
+	if (atomic_read(&clp->cl_delegs_in_recall))
+		return true;
+	spin_lock(&clp->cl_lock);
+	for (i = 0; i < OWNER_HASH_SIZE; i++) {
+		list_for_each_entry(so, &clp->cl_ownerstr_hashtbl[i],
+				so_strhash) {
+			if (so->so_is_open_owner)
+				continue;
+			lo = lockowner(so);
+			if (nfs4_lockowner_has_blockers(lo)) {
+				spin_unlock(&clp->cl_lock);
+				return true;
+			}
+		}
+	}
+	spin_unlock(&clp->cl_lock);
+	return false;
+}
+
+static void
+nfs4_get_client_reaplist(struct nfsd_net *nn, struct list_head *reaplist,
+				struct laundry_time *lt)
+{
+	unsigned int maxreap, reapcnt = 0;
+	struct list_head *pos, *next;
+	struct nfs4_client *clp;
+
+	maxreap = (atomic_read(&nn->nfs4_client_count) >= nn->nfs4_max_clients) ?
+			NFSD_CLIENT_MAX_TRIM_PER_RUN : 0;
+	INIT_LIST_HEAD(reaplist);
+	spin_lock(&nn->client_lock);
+	list_for_each_safe(pos, next, &nn->client_lru) {
+		clp = list_entry(pos, struct nfs4_client, cl_lru);
+		if (clp->cl_state == NFSD4_EXPIRABLE)
+			goto exp_client;
+		if (!state_expired(lt, clp->cl_time))
+			break;
+		if (!atomic_read(&clp->cl_rpc_users)) {
+			if (clp->cl_state == NFSD4_ACTIVE)
+				atomic_inc(&nn->nfsd_courtesy_clients);
+			clp->cl_state = NFSD4_COURTESY;
+		}
+		if (!client_has_state(clp))
+			goto exp_client;
+		if (!nfs4_anylock_blockers(clp))
+			if (reapcnt >= maxreap)
+				continue;
+exp_client:
+		if (!mark_client_expired_locked(clp)) {
+			list_add(&clp->cl_lru, reaplist);
+			reapcnt++;
+		}
+	}
+	spin_unlock(&nn->client_lock);
+}
+
+static void
+nfs4_get_courtesy_client_reaplist(struct nfsd_net *nn,
+				struct list_head *reaplist)
+{
+	unsigned int maxreap = 0, reapcnt = 0;
+	struct list_head *pos, *next;
+	struct nfs4_client *clp;
+
+	maxreap = NFSD_CLIENT_MAX_TRIM_PER_RUN;
+	INIT_LIST_HEAD(reaplist);
+
+	spin_lock(&nn->client_lock);
+	list_for_each_safe(pos, next, &nn->client_lru) {
+		clp = list_entry(pos, struct nfs4_client, cl_lru);
+		if (clp->cl_state == NFSD4_ACTIVE)
+			break;
+		if (reapcnt >= maxreap)
+			break;
+		if (!mark_client_expired_locked(clp)) {
+			list_add(&clp->cl_lru, reaplist);
+			reapcnt++;
+		}
+	}
+	spin_unlock(&nn->client_lock);
+}
+
+static void
+nfs4_process_client_reaplist(struct list_head *reaplist)
+{
+	struct list_head *pos, *next;
+	struct nfs4_client *clp;
+
+	list_for_each_safe(pos, next, reaplist) {
+		clp = list_entry(pos, struct nfs4_client, cl_lru);
+		trace_nfsd_clid_purged(&clp->cl_clientid);
+		list_del_init(&clp->cl_lru);
+		expire_client(clp);
+	}
+}
+
 static time64_t
 nfs4_laundromat(struct nfsd_net *nn)
 {
-	struct nfs4_client *clp;
 	struct nfs4_openowner *oo;
 	struct nfs4_delegation *dp;
 	struct nfs4_ol_stateid *stp;
@@ -5594,33 +6136,18 @@
 		goto out;
 	}
 	nfsd4_end_grace(nn);
-	INIT_LIST_HEAD(&reaplist);
 
 	spin_lock(&nn->s2s_cp_lock);
 	idr_for_each_entry(&nn->s2s_cp_stateids, cps_t, i) {
 		cps = container_of(cps_t, struct nfs4_cpntf_state, cp_stateid);
-		if (cps->cp_stateid.sc_type == NFS4_COPYNOTIFY_STID &&
+		if (cps->cp_stateid.cs_type == NFS4_COPYNOTIFY_STID &&
 				state_expired(&lt, cps->cpntf_time))
 			_free_cpntf_state_locked(nn, cps);
 	}
 	spin_unlock(&nn->s2s_cp_lock);
+	nfs4_get_client_reaplist(nn, &reaplist, &lt);
+	nfs4_process_client_reaplist(&reaplist);
 
-	spin_lock(&nn->client_lock);
-	list_for_each_safe(pos, next, &nn->client_lru) {
-		clp = list_entry(pos, struct nfs4_client, cl_lru);
-		if (!state_expired(&lt, clp->cl_time))
-			break;
-		if (mark_client_expired_locked(clp))
-			continue;
-		list_add(&clp->cl_lru, &reaplist);
-	}
-	spin_unlock(&nn->client_lock);
-	list_for_each_safe(pos, next, &reaplist) {
-		clp = list_entry(pos, struct nfs4_client, cl_lru);
-		trace_nfsd_clid_purged(&clp->cl_clientid);
-		list_del_init(&clp->cl_lru);
-		expire_client(clp);
-	}
 	spin_lock(&state_lock);
 	list_for_each_safe(pos, next, &nn->del_recall_lru) {
 		dp = list_entry (pos, struct nfs4_delegation, dl_recall_lru);
@@ -5689,7 +6216,6 @@
 	return max_t(time64_t, lt.new_timeo, NFSD_LAUNDROMAT_MINTIMEOUT);
 }
 
-static struct workqueue_struct *laundry_wq;
 static void laundromat_main(struct work_struct *);
 
 static void
@@ -5704,6 +6230,69 @@
 	queue_delayed_work(laundry_wq, &nn->laundromat_work, t*HZ);
 }
 
+static void
+courtesy_client_reaper(struct nfsd_net *nn)
+{
+	struct list_head reaplist;
+
+	nfs4_get_courtesy_client_reaplist(nn, &reaplist);
+	nfs4_process_client_reaplist(&reaplist);
+}
+
+static void
+deleg_reaper(struct nfsd_net *nn)
+{
+	struct list_head *pos, *next;
+	struct nfs4_client *clp;
+	struct list_head cblist;
+
+	INIT_LIST_HEAD(&cblist);
+	spin_lock(&nn->client_lock);
+	list_for_each_safe(pos, next, &nn->client_lru) {
+		clp = list_entry(pos, struct nfs4_client, cl_lru);
+
+		if (clp->cl_state != NFSD4_ACTIVE)
+			continue;
+		if (list_empty(&clp->cl_delegations))
+			continue;
+		if (atomic_read(&clp->cl_delegs_in_recall))
+			continue;
+		if (test_bit(NFSD4_CLIENT_CB_RECALL_ANY, &clp->cl_flags))
+			continue;
+		if (ktime_get_boottime_seconds() - clp->cl_ra_time < 5)
+			continue;
+		if (clp->cl_cb_state != NFSD4_CB_UP)
+			continue;
+		list_add(&clp->cl_ra_cblist, &cblist);
+
+		/* release in nfsd4_cb_recall_any_release */
+		kref_get(&clp->cl_nfsdfs.cl_ref);
+		set_bit(NFSD4_CLIENT_CB_RECALL_ANY, &clp->cl_flags);
+		clp->cl_ra_time = ktime_get_boottime_seconds();
+	}
+	spin_unlock(&nn->client_lock);
+
+	while (!list_empty(&cblist)) {
+		clp = list_first_entry(&cblist, struct nfs4_client,
+					cl_ra_cblist);
+		list_del_init(&clp->cl_ra_cblist);
+		clp->cl_ra->ra_keep = 0;
+		clp->cl_ra->ra_bmval[0] = BIT(RCA4_TYPE_MASK_RDATA_DLG);
+		trace_nfsd_cb_recall_any(clp->cl_ra);
+		nfsd4_run_cb(&clp->cl_ra->ra_cb);
+	}
+}
+
+static void
+nfsd4_state_shrinker_worker(struct work_struct *work)
+{
+	struct nfsd_net *nn = container_of(work, struct nfsd_net,
+				nfsd_shrinker_work);
+
+	courtesy_client_reaper(nn);
+	deleg_reaper(nn);
+}
+
 static inline __be32 nfs4_check_fh(struct svc_fh *fhp, struct nfs4_stid *stp)
 {
 	if (!fh_match(&fhp->fh_handle, &stp->sc_file->fi_fhandle))
@@ -5801,8 +6390,6 @@
 	if (ZERO_STATEID(stateid) || ONE_STATEID(stateid) ||
 		CLOSE_STATEID(stateid))
 		return status;
-	if (!same_clid(&stateid->si_opaque.so_clid, &cl->cl_clientid))
-		return status;
 	spin_lock(&cl->cl_lock);
 	s = find_stateid_locked(cl, stateid);
 	if (!s)
@@ -5839,6 +6426,7 @@
 		     struct nfs4_stid **s, struct nfsd_net *nn)
 {
 	__be32 status;
+	struct nfs4_stid *stid;
 	bool return_revoked = false;
 
 	/*
@@ -5861,15 +6449,16 @@
 	}
 	if (status)
 		return status;
-	*s = find_stateid_by_type(cstate->clp, stateid, typemask);
-	if (!*s)
+	stid = find_stateid_by_type(cstate->clp, stateid, typemask);
+	if (!stid)
 		return nfserr_bad_stateid;
-	if (((*s)->sc_type == NFS4_REVOKED_DELEG_STID) && !return_revoked) {
-		nfs4_put_stid(*s);
+	if ((stid->sc_type == NFS4_REVOKED_DELEG_STID) && !return_revoked) {
+		nfs4_put_stid(stid);
 		if (cstate->minorversion)
 			return nfserr_deleg_revoked;
 		return nfserr_bad_stateid;
 	}
+	*s = stid;
 	return nfs_ok;
 }
 
@@ -5934,12 +6523,12 @@
 static void
 _free_cpntf_state_locked(struct nfsd_net *nn, struct nfs4_cpntf_state *cps)
 {
-	WARN_ON_ONCE(cps->cp_stateid.sc_type != NFS4_COPYNOTIFY_STID);
-	if (!refcount_dec_and_test(&cps->cp_stateid.sc_count))
+	WARN_ON_ONCE(cps->cp_stateid.cs_type != NFS4_COPYNOTIFY_STID);
+	if (!refcount_dec_and_test(&cps->cp_stateid.cs_count))
 		return;
 	list_del(&cps->cp_list);
 	idr_remove(&nn->s2s_cp_stateids,
-		   cps->cp_stateid.stid.si_opaque.so_id);
+		   cps->cp_stateid.cs_stid.si_opaque.so_id);
 	kfree(cps);
 }
 /*
@@ -5961,12 +6550,12 @@
 	if (cps_t) {
 		state = container_of(cps_t, struct nfs4_cpntf_state,
 				     cp_stateid);
-		if (state->cp_stateid.sc_type != NFS4_COPYNOTIFY_STID) {
+		if (state->cp_stateid.cs_type != NFS4_COPYNOTIFY_STID) {
 			state = NULL;
 			goto unlock;
 		}
 		if (!clp)
-			refcount_inc(&state->cp_stateid.sc_count);
+			refcount_inc(&state->cp_stateid.cs_count);
 		else
 			_free_cpntf_state_locked(nn, state);
 	}
@@ -6035,7 +6624,11 @@
 		*nfp = NULL;
 
 	if (ZERO_STATEID(stateid) || ONE_STATEID(stateid)) {
-		status = check_special_stateids(net, fhp, stateid, flags);
+		if (cstid)
+			status = nfserr_bad_stateid;
+		else
+			status = check_special_stateids(net, fhp, stateid,
+									flags);
 		goto done;
 	}
 
@@ -6370,6 +6963,7 @@
 	struct nfs4_client *clp = s->st_stid.sc_client;
 	bool unhashed;
 	LIST_HEAD(reaplist);
+	struct nfs4_ol_stateid *stp;
 
 	spin_lock(&clp->cl_lock);
 	unhashed = unhash_open_stateid(s, &reaplist);
@@ -6378,6 +6972,8 @@
 		if (unhashed)
 			put_ol_stateid_locked(s, &reaplist);
 		spin_unlock(&clp->cl_lock);
+		list_for_each_entry(stp, &reaplist, st_locks)
+			nfs4_free_cpntf_statelist(clp->net, &stp->st_stid);
 		free_ol_stateid_reaplist(&reaplist);
 	} else {
 		spin_unlock(&clp->cl_lock);
@@ -6461,6 +7057,8 @@
 	if (status)
 		goto put_stateid;
 
+	trace_nfsd_deleg_return(stateid);
+	wake_up_var(d_inode(cstate->current_fh.fh_dentry));
 	destroy_delegation(dp);
 put_stateid:
 	nfs4_put_stid(&dp->dl_stid);
@@ -6497,7 +7095,7 @@
 }
 
 static fl_owner_t
-nfsd4_fl_get_owner(fl_owner_t owner)
+nfsd4_lm_get_owner(fl_owner_t owner)
 {
 	struct nfs4_lockowner *lo = (struct nfs4_lockowner *)owner;
 
@@ -6506,7 +7104,7 @@
 }
 
 static void
-nfsd4_fl_put_owner(fl_owner_t owner)
+nfsd4_lm_put_owner(fl_owner_t owner)
 {
 	struct nfs4_lockowner *lo = (struct nfs4_lockowner *)owner;
 
@@ -6514,6 +7112,29 @@
 		nfs4_put_stateowner(&lo->lo_owner);
 }
 
+/* return pointer to struct nfs4_client if client is expirable */
+static bool
+nfsd4_lm_lock_expirable(struct file_lock *cfl)
+{
+	struct nfs4_lockowner *lo = (struct nfs4_lockowner *)cfl->fl_owner;
+	struct nfs4_client *clp = lo->lo_owner.so_client;
+	struct nfsd_net *nn;
+
+	if (try_to_expire_client(clp)) {
+		nn = net_generic(clp->net, nfsd_net_id);
+		mod_delayed_work(laundry_wq, &nn->laundromat_work, 0);
+		return true;
+	}
+	return false;
+}
+
+/* schedule laundromat to run immediately and wait for it to complete */
+static void
+nfsd4_lm_expire_lock(void)
+{
+	flush_workqueue(laundry_wq);
+}
+
 static void
 nfsd4_lm_notify(struct file_lock *fl)
 {
@@ -6540,9 +7161,12 @@
 }
 
 static const struct lock_manager_operations nfsd_posix_mng_ops  = {
+	.lm_mod_owner = THIS_MODULE,
 	.lm_notify = nfsd4_lm_notify,
-	.lm_get_owner = nfsd4_fl_get_owner,
-	.lm_put_owner = nfsd4_fl_put_owner,
+	.lm_get_owner = nfsd4_lm_get_owner,
+	.lm_put_owner = nfsd4_lm_put_owner,
+	.lm_lock_expirable = nfsd4_lm_lock_expirable,
+	.lm_expire_lock = nfsd4_lm_expire_lock,
 };
 
 static inline void
@@ -6831,7 +7455,6 @@
 	struct nfsd4_blocked_lock *nbl = NULL;
 	struct file_lock *file_lock = NULL;
 	struct file_lock *conflock = NULL;
-	struct super_block *sb;
 	__be32 status = 0;
 	int lkflg;
 	int err;
@@ -6853,7 +7476,6 @@
 		dprintk("NFSD: nfsd4_lock: permission denied!\n");
 		return status;
 	}
-	sb = cstate->current_fh.fh_dentry->d_sb;
 
 	if (lock->lk_is_new) {
 		if (nfsd4_has_session(cstate))
@@ -6905,8 +7527,7 @@
 	fp = lock_stp->st_stid.sc_file;
 	switch (lock->lk_type) {
 		case NFS4_READW_LT:
-			if (nfsd4_has_session(cstate) &&
-			    !(sb->s_export_op->flags & EXPORT_OP_SYNC_LOCKS))
+			if (nfsd4_has_session(cstate))
 				fl_flags |= FL_SLEEP;
 			fallthrough;
 		case NFS4_READ_LT:
@@ -6918,8 +7539,7 @@
 			fl_type = F_RDLCK;
 			break;
 		case NFS4_WRITEW_LT:
-			if (nfsd4_has_session(cstate) &&
-			    !(sb->s_export_op->flags & EXPORT_OP_SYNC_LOCKS))
+			if (nfsd4_has_session(cstate))
 				fl_flags |= FL_SLEEP;
 			fallthrough;
 		case NFS4_WRITE_LT:
@@ -6940,6 +7560,16 @@
 		goto out;
 	}
 
+	/*
+	 * Most filesystems with their own ->lock operations will block
+	 * the nfsd thread waiting to acquire the lock.  That leads to
+	 * deadlocks (we don't want every nfsd thread tied up waiting
+	 * for file locks), so don't attempt blocking lock notifications
+	 * on those filesystems:
+	 */
+	if (nf->nf_file->f_op->lock)
+		fl_flags &= ~FL_SLEEP;
+
 	nbl = find_or_allocate_block(lock_sop, &fp->fi_fhandle, nn);
 	if (!nbl) {
 		dprintk("NFSD: %s: unable to allocate block!\n", __func__);
@@ -6970,6 +7600,7 @@
 		spin_lock(&nn->blocked_locks_lock);
 		list_add_tail(&nbl->nbl_list, &lock_sop->lo_blocked);
 		list_add_tail(&nbl->nbl_lru, &nn->blocked_locks_lru);
+		kref_get(&nbl->nbl_kref);
 		spin_unlock(&nn->blocked_locks_lock);
 	}
 
@@ -6982,6 +7613,7 @@
 			nn->somebody_reclaimed = true;
 		break;
 	case FILE_LOCK_DEFERRED:
+		kref_put(&nbl->nbl_kref, free_nbl);
 		nbl = NULL;
 		fallthrough;
 	case -EAGAIN:		/* conflock holds conflicting lock */
@@ -7002,8 +7634,13 @@
 		/* dequeue it if we queued it before */
 		if (fl_flags & FL_SLEEP) {
 			spin_lock(&nn->blocked_locks_lock);
-			list_del_init(&nbl->nbl_list);
-			list_del_init(&nbl->nbl_lru);
+			if (!list_empty(&nbl->nbl_list) &&
+			    !list_empty(&nbl->nbl_lru)) {
+				list_del_init(&nbl->nbl_list);
+				list_del_init(&nbl->nbl_lru);
+				kref_put(&nbl->nbl_kref, free_nbl);
+			}
+			/* nbl can use one of lists to be linked to reaplist */
 			spin_unlock(&nn->blocked_locks_lock);
 		}
 		free_blocked_lock(nbl);
@@ -7044,21 +7681,22 @@
 static __be32 nfsd_test_lock(struct svc_rqst *rqstp, struct svc_fh *fhp, struct file_lock *lock)
 {
 	struct nfsd_file *nf;
+	struct inode *inode;
 	__be32 err;
 
 	err = nfsd_file_acquire(rqstp, fhp, NFSD_MAY_READ, &nf);
 	if (err)
 		return err;
-	fh_lock(fhp); /* to block new leases till after test_lock: */
-	err = nfserrno(nfsd_open_break_lease(fhp->fh_dentry->d_inode,
-							NFSD_MAY_READ));
+	inode = fhp->fh_dentry->d_inode;
+	inode_lock(inode); /* to block new leases till after test_lock: */
+	err = nfserrno(nfsd_open_break_lease(inode, NFSD_MAY_READ));
 	if (err)
 		goto out;
 	lock->fl_file = nf->nf_file;
 	err = nfserrno(vfs_test_lock(nf->nf_file, lock));
 	lock->fl_file = NULL;
 out:
-	fh_unlock(fhp);
+	inode_unlock(inode);
 	nfsd_file_put(nf);
 	return err;
 }
@@ -7220,18 +7858,20 @@
 {
 	struct file_lock *fl;
 	int status = false;
-	struct nfsd_file *nf = find_any_file(fp);
+	struct nfsd_file *nf;
 	struct inode *inode;
 	struct file_lock_context *flctx;
 
+	spin_lock(&fp->fi_lock);
+	nf = find_any_file_locked(fp);
 	if (!nf) {
 		/* Any valid lock stateid should have some sort of access */
 		WARN_ON_ONCE(1);
-		return status;
+		goto out;
 	}
 
 	inode = locks_inode(nf->nf_file);
-	flctx = inode->i_flctx;
+	flctx = locks_inode_context(inode);
 
 	if (flctx && !list_empty_careful(&flctx->flc_posix)) {
 		spin_lock(&flctx->flc_lock);
@@ -7243,26 +7883,39 @@
 		}
 		spin_unlock(&flctx->flc_lock);
 	}
-	nfsd_file_put(nf);
+out:
+	spin_unlock(&fp->fi_lock);
 	return status;
 }
 
+/**
+ * nfsd4_release_lockowner - process NFSv4.0 RELEASE_LOCKOWNER operations
+ * @rqstp: RPC transaction
+ * @cstate: NFSv4 COMPOUND state
+ * @u: RELEASE_LOCKOWNER arguments
+ *
+ * Check if theree are any locks still held and if not - free the lockowner
+ * and any lock state that is owned.
+ *
+ * Return values:
+ *   %nfs_ok: lockowner released or not found
+ *   %nfserr_locks_held: lockowner still in use
+ *   %nfserr_stale_clientid: clientid no longer active
+ *   %nfserr_expired: clientid not recognized
+ */
 __be32
 nfsd4_release_lockowner(struct svc_rqst *rqstp,
 			struct nfsd4_compound_state *cstate,
 			union nfsd4_op_u *u)
 {
 	struct nfsd4_release_lockowner *rlockowner = &u->release_lockowner;
+	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 	clientid_t *clid = &rlockowner->rl_clientid;
-	struct nfs4_stateowner *sop;
-	struct nfs4_lockowner *lo = NULL;
 	struct nfs4_ol_stateid *stp;
-	struct xdr_netobj *owner = &rlockowner->rl_owner;
-	unsigned int hashval = ownerstr_hashval(owner);
-	__be32 status;
-	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
+	struct nfs4_lockowner *lo;
 	struct nfs4_client *clp;
-	LIST_HEAD (reaplist);
+	LIST_HEAD(reaplist);
+	__be32 status;
 
 	dprintk("nfsd4_release_lockowner clientid: (%08x/%08x):\n",
 		clid->cl_boot, clid->cl_id);
@@ -7270,34 +7923,22 @@
 	status = set_client(clid, cstate, nn);
 	if (status)
 		return status;
-
 	clp = cstate->clp;
-	/* Find the matching lock stateowner */
-	spin_lock(&clp->cl_lock);
-	list_for_each_entry(sop, &clp->cl_ownerstr_hashtbl[hashval],
-			    so_strhash) {
-
-		if (sop->so_is_open_owner || !same_owner_str(sop, owner))
-			continue;
-
-		/* see if there are still any locks associated with it */
-		lo = lockowner(sop);
-		list_for_each_entry(stp, &sop->so_stateids, st_perstateowner) {
-			if (check_for_locks(stp->st_stid.sc_file, lo)) {
-				status = nfserr_locks_held;
-				spin_unlock(&clp->cl_lock);
-				return status;
-			}
-		}
 
-		nfs4_get_stateowner(sop);
-		break;
-	}
+	spin_lock(&clp->cl_lock);
+	lo = find_lockowner_str_locked(clp, &rlockowner->rl_owner);
 	if (!lo) {
 		spin_unlock(&clp->cl_lock);
-		return status;
+		return nfs_ok;
 	}
 
+	list_for_each_entry(stp, &lo->lo_owner.so_stateids, st_perstateowner) {
+		if (check_for_locks(stp->st_stid.sc_file, lo)) {
+			spin_unlock(&clp->cl_lock);
+			nfs4_put_stateowner(&lo->lo_owner);
+			return nfserr_locks_held;
+		}
+	}
 	unhash_lockowner_locked(lo);
 	while (!list_empty(&lo->lo_owner.so_stateids)) {
 		stp = list_first_entry(&lo->lo_owner.so_stateids,
@@ -7307,11 +7948,11 @@
 		put_ol_stateid_locked(stp, &reaplist);
 	}
 	spin_unlock(&clp->cl_lock);
+
 	free_ol_stateid_reaplist(&reaplist);
 	remove_blocked_locks(lo);
 	nfs4_put_stateowner(&lo->lo_owner);
-
-	return status;
+	return nfs_ok;
 }
 
 static inline struct nfs4_client_reclaim *
@@ -7472,15 +8113,26 @@
 	spin_lock_init(&nn->client_lock);
 	spin_lock_init(&nn->s2s_cp_lock);
 	idr_init(&nn->s2s_cp_stateids);
+	atomic_set(&nn->pending_async_copies, 0);
 
 	spin_lock_init(&nn->blocked_locks_lock);
 	INIT_LIST_HEAD(&nn->blocked_locks_lru);
 
 	INIT_DELAYED_WORK(&nn->laundromat_work, laundromat_main);
+	INIT_WORK(&nn->nfsd_shrinker_work, nfsd4_state_shrinker_worker);
 	get_net(net);
 
+	nn->nfsd_client_shrinker.scan_objects = nfsd4_state_shrinker_scan;
+	nn->nfsd_client_shrinker.count_objects = nfsd4_state_shrinker_count;
+	nn->nfsd_client_shrinker.seeks = DEFAULT_SEEKS;
+
+	if (register_shrinker(&nn->nfsd_client_shrinker))
+		goto err_shrinker;
 	return 0;
 
+err_shrinker:
+	put_net(net);
+	kfree(nn->sessionid_hashtbl);
 err_sessionid:
 	kfree(nn->unconf_id_hashtbl);
 err_unconf_id:
@@ -7552,22 +8204,18 @@
 {
 	int ret;
 
-	laundry_wq = alloc_workqueue("%s", WQ_UNBOUND, 0, "nfsd4");
-	if (laundry_wq == NULL) {
-		ret = -ENOMEM;
-		goto out;
-	}
-	ret = nfsd4_create_callback_queue();
+	ret = rhltable_init(&nfs4_file_rhltable, &nfs4_file_rhash_params);
 	if (ret)
-		goto out_free_laundry;
+		return ret;
+
+	ret = nfsd4_create_callback_queue();
+	if (ret) {
+		rhltable_destroy(&nfs4_file_rhltable);
+		return ret;
+	}
 
 	set_max_delegations();
 	return 0;
-
-out_free_laundry:
-	destroy_workqueue(laundry_wq);
-out:
-	return ret;
 }
 
 void
@@ -7577,6 +8225,8 @@
 	struct list_head *pos, *next, reaplist;
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 
+	unregister_shrinker(&nn->nfsd_client_shrinker);
+	cancel_work_sync(&nn->nfsd_shrinker_work);
 	cancel_delayed_work_sync(&nn->laundromat_work);
 	locks_end_grace(&nn->nfsd4_manager);
 
@@ -7604,8 +8254,8 @@
 void
 nfs4_state_shutdown(void)
 {
-	destroy_workqueue(laundry_wq);
 	nfsd4_destroy_callback_queue();
+	rhltable_destroy(&nfs4_file_rhltable);
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfs4xdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfs4xdr.c
@@ -42,6 +42,8 @@
 #include <linux/sunrpc/svcauth_gss.h>
 #include <linux/sunrpc/addr.h>
 #include <linux/xattr.h>
+#include <linux/vmalloc.h>
+
 #include <uapi/linux/xattr.h>
 
 #include "idmap.h"
@@ -277,24 +279,10 @@
 static __be32
 nfsd4_decode_bitmap4(struct nfsd4_compoundargs *argp, u32 *bmval, u32 bmlen)
 {
-	u32 i, count;
-	__be32 *p;
-
-	if (xdr_stream_decode_u32(argp->xdr, &count) < 0)
-		return nfserr_bad_xdr;
-	/* request sanity */
-	if (count > 1000)
-		return nfserr_bad_xdr;
-	p = xdr_inline_decode(argp->xdr, count << 2);
-	if (!p)
-		return nfserr_bad_xdr;
-	i = 0;
-	while (i < count)
-		bmval[i++] = be32_to_cpup(p++);
-	while (i < bmlen)
-		bmval[i++] = 0;
+	ssize_t status;
 
-	return nfs_ok;
+	status = xdr_stream_decode_uint32_array(argp->xdr, bmval, bmlen);
+	return status == -EBADMSG ? nfserr_bad_xdr : nfs_ok;
 }
 
 static __be32
@@ -484,6 +472,15 @@
 			return nfserr_bad_xdr;
 		}
 	}
+	if (bmval[1] & FATTR4_WORD1_TIME_CREATE) {
+		struct timespec64 ts;
+
+		/* No Linux filesystem supports setting this attribute. */
+		bmval[1] &= ~FATTR4_WORD1_TIME_CREATE;
+		status = nfsd4_decode_nfstime4(argp, &ts);
+		if (status)
+			return status;
+	}
 	if (bmval[1] & FATTR4_WORD1_TIME_MODIFY_SET) {
 		u32 set_it;
 
@@ -773,16 +770,18 @@
 
 static __be32
 nfsd4_decode_access(struct nfsd4_compoundargs *argp,
-		    struct nfsd4_access *access)
+		    union nfsd4_op_u *u)
 {
+	struct nfsd4_access *access = &u->access;
 	if (xdr_stream_decode_u32(argp->xdr, &access->ac_req_access) < 0)
 		return nfserr_bad_xdr;
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_close(struct nfsd4_compoundargs *argp, struct nfsd4_close *close)
+nfsd4_decode_close(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_close *close = &u->close;
 	if (xdr_stream_decode_u32(argp->xdr, &close->cl_seqid) < 0)
 		return nfserr_bad_xdr;
 	return nfsd4_decode_stateid4(argp, &close->cl_stateid);
@@ -790,20 +789,24 @@
 
 
 static __be32
-nfsd4_decode_commit(struct nfsd4_compoundargs *argp, struct nfsd4_commit *commit)
+nfsd4_decode_commit(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_commit *commit = &u->commit;
 	if (xdr_stream_decode_u64(argp->xdr, &commit->co_offset) < 0)
 		return nfserr_bad_xdr;
 	if (xdr_stream_decode_u32(argp->xdr, &commit->co_count) < 0)
 		return nfserr_bad_xdr;
+	memset(&commit->co_verf, 0, sizeof(commit->co_verf));
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_create(struct nfsd4_compoundargs *argp, struct nfsd4_create *create)
+nfsd4_decode_create(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_create *create = &u->create;
 	__be32 *p, status;
 
+	memset(create, 0, sizeof(*create));
 	if (xdr_stream_decode_u32(argp->xdr, &create->cr_type) < 0)
 		return nfserr_bad_xdr;
 	switch (create->cr_type) {
@@ -845,21 +848,26 @@
 }
 
 static inline __be32
-nfsd4_decode_delegreturn(struct nfsd4_compoundargs *argp, struct nfsd4_delegreturn *dr)
+nfsd4_decode_delegreturn(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_delegreturn *dr = &u->delegreturn;
 	return nfsd4_decode_stateid4(argp, &dr->dr_stateid);
 }
 
 static inline __be32
-nfsd4_decode_getattr(struct nfsd4_compoundargs *argp, struct nfsd4_getattr *getattr)
+nfsd4_decode_getattr(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_getattr *getattr = &u->getattr;
+	memset(getattr, 0, sizeof(*getattr));
 	return nfsd4_decode_bitmap4(argp, getattr->ga_bmval,
 				    ARRAY_SIZE(getattr->ga_bmval));
 }
 
 static __be32
-nfsd4_decode_link(struct nfsd4_compoundargs *argp, struct nfsd4_link *link)
+nfsd4_decode_link(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_link *link = &u->link;
+	memset(link, 0, sizeof(*link));
 	return nfsd4_decode_component4(argp, &link->li_name, &link->li_namelen);
 }
 
@@ -906,8 +914,10 @@
 }
 
 static __be32
-nfsd4_decode_lock(struct nfsd4_compoundargs *argp, struct nfsd4_lock *lock)
+nfsd4_decode_lock(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_lock *lock = &u->lock;
+	memset(lock, 0, sizeof(*lock));
 	if (xdr_stream_decode_u32(argp->xdr, &lock->lk_type) < 0)
 		return nfserr_bad_xdr;
 	if ((lock->lk_type < NFS4_READ_LT) || (lock->lk_type > NFS4_WRITEW_LT))
@@ -922,8 +932,10 @@
 }
 
 static __be32
-nfsd4_decode_lockt(struct nfsd4_compoundargs *argp, struct nfsd4_lockt *lockt)
+nfsd4_decode_lockt(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_lockt *lockt = &u->lockt;
+	memset(lockt, 0, sizeof(*lockt));
 	if (xdr_stream_decode_u32(argp->xdr, &lockt->lt_type) < 0)
 		return nfserr_bad_xdr;
 	if ((lockt->lt_type < NFS4_READ_LT) || (lockt->lt_type > NFS4_WRITEW_LT))
@@ -937,8 +949,9 @@
 }
 
 static __be32
-nfsd4_decode_locku(struct nfsd4_compoundargs *argp, struct nfsd4_locku *locku)
+nfsd4_decode_locku(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_locku *locku = &u->locku;
 	__be32 status;
 
 	if (xdr_stream_decode_u32(argp->xdr, &locku->lu_type) < 0)
@@ -959,8 +972,9 @@
 }
 
 static __be32
-nfsd4_decode_lookup(struct nfsd4_compoundargs *argp, struct nfsd4_lookup *lookup)
+nfsd4_decode_lookup(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_lookup *lookup = &u->lookup;
 	return nfsd4_decode_component4(argp, &lookup->lo_name, &lookup->lo_len);
 }
 
@@ -1140,16 +1154,14 @@
 }
 
 static __be32
-nfsd4_decode_open(struct nfsd4_compoundargs *argp, struct nfsd4_open *open)
+nfsd4_decode_open(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_open *open = &u->open;
 	__be32 status;
 	u32 dummy;
 
-	memset(open->op_bmval, 0, sizeof(open->op_bmval));
-	open->op_iattr.ia_valid = 0;
-	open->op_openowner = NULL;
+	memset(open, 0, sizeof(*open));
 
-	open->op_xdr_error = 0;
 	if (xdr_stream_decode_u32(argp->xdr, &open->op_seqid) < 0)
 		return nfserr_bad_xdr;
 	/* deleg_want is ignored */
@@ -1171,8 +1183,10 @@
 }
 
 static __be32
-nfsd4_decode_open_confirm(struct nfsd4_compoundargs *argp, struct nfsd4_open_confirm *open_conf)
+nfsd4_decode_open_confirm(struct nfsd4_compoundargs *argp,
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_open_confirm *open_conf = &u->open_confirm;
 	__be32 status;
 
 	if (argp->minorversion >= 1)
@@ -1184,14 +1198,19 @@
 	if (xdr_stream_decode_u32(argp->xdr, &open_conf->oc_seqid) < 0)
 		return nfserr_bad_xdr;
 
+	memset(&open_conf->oc_resp_stateid, 0,
+	       sizeof(open_conf->oc_resp_stateid));
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_open_downgrade(struct nfsd4_compoundargs *argp, struct nfsd4_open_downgrade *open_down)
+nfsd4_decode_open_downgrade(struct nfsd4_compoundargs *argp,
+			    union nfsd4_op_u *u)
 {
+	struct nfsd4_open_downgrade *open_down = &u->open_downgrade;
 	__be32 status;
 
+	memset(open_down, 0, sizeof(*open_down));
 	status = nfsd4_decode_stateid4(argp, &open_down->od_stateid);
 	if (status)
 		return status;
@@ -1206,8 +1225,9 @@
 }
 
 static __be32
-nfsd4_decode_putfh(struct nfsd4_compoundargs *argp, struct nfsd4_putfh *putfh)
+nfsd4_decode_putfh(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_putfh *putfh = &u->putfh;
 	__be32 *p;
 
 	if (xdr_stream_decode_u32(argp->xdr, &putfh->pf_fhlen) < 0)
@@ -1221,22 +1241,17 @@
 	if (!putfh->pf_fhval)
 		return nfserr_jukebox;
 
+	putfh->no_verify = false;
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_putpubfh(struct nfsd4_compoundargs *argp, void *p)
-{
-	if (argp->minorversion == 0)
-		return nfs_ok;
-	return nfserr_notsupp;
-}
-
-static __be32
-nfsd4_decode_read(struct nfsd4_compoundargs *argp, struct nfsd4_read *read)
+nfsd4_decode_read(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_read *read = &u->read;
 	__be32 status;
 
+	memset(read, 0, sizeof(*read));
 	status = nfsd4_decode_stateid4(argp, &read->rd_stateid);
 	if (status)
 		return status;
@@ -1249,10 +1264,12 @@
 }
 
 static __be32
-nfsd4_decode_readdir(struct nfsd4_compoundargs *argp, struct nfsd4_readdir *readdir)
+nfsd4_decode_readdir(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_readdir *readdir = &u->readdir;
 	__be32 status;
 
+	memset(readdir, 0, sizeof(*readdir));
 	if (xdr_stream_decode_u64(argp->xdr, &readdir->rd_cookie) < 0)
 		return nfserr_bad_xdr;
 	status = nfsd4_decode_verifier4(argp, &readdir->rd_verf);
@@ -1270,16 +1287,20 @@
 }
 
 static __be32
-nfsd4_decode_remove(struct nfsd4_compoundargs *argp, struct nfsd4_remove *remove)
+nfsd4_decode_remove(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_remove *remove = &u->remove;
+	memset(&remove->rm_cinfo, 0, sizeof(remove->rm_cinfo));
 	return nfsd4_decode_component4(argp, &remove->rm_name, &remove->rm_namelen);
 }
 
 static __be32
-nfsd4_decode_rename(struct nfsd4_compoundargs *argp, struct nfsd4_rename *rename)
+nfsd4_decode_rename(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_rename *rename = &u->rename;
 	__be32 status;
 
+	memset(rename, 0, sizeof(*rename));
 	status = nfsd4_decode_component4(argp, &rename->rn_sname, &rename->rn_snamelen);
 	if (status)
 		return status;
@@ -1287,23 +1308,28 @@
 }
 
 static __be32
-nfsd4_decode_renew(struct nfsd4_compoundargs *argp, clientid_t *clientid)
+nfsd4_decode_renew(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	clientid_t *clientid = &u->renew;
 	return nfsd4_decode_clientid4(argp, clientid);
 }
 
 static __be32
 nfsd4_decode_secinfo(struct nfsd4_compoundargs *argp,
-		     struct nfsd4_secinfo *secinfo)
+		     union nfsd4_op_u *u)
 {
+	struct nfsd4_secinfo *secinfo = &u->secinfo;
+	secinfo->si_exp = NULL;
 	return nfsd4_decode_component4(argp, &secinfo->si_name, &secinfo->si_namelen);
 }
 
 static __be32
-nfsd4_decode_setattr(struct nfsd4_compoundargs *argp, struct nfsd4_setattr *setattr)
+nfsd4_decode_setattr(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_setattr *setattr = &u->setattr;
 	__be32 status;
 
+	memset(setattr, 0, sizeof(*setattr));
 	status = nfsd4_decode_stateid4(argp, &setattr->sa_stateid);
 	if (status)
 		return status;
@@ -1314,10 +1340,13 @@
 }
 
 static __be32
-nfsd4_decode_setclientid(struct nfsd4_compoundargs *argp, struct nfsd4_setclientid *setclientid)
+nfsd4_decode_setclientid(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_setclientid *setclientid = &u->setclientid;
 	__be32 *p, status;
 
+	memset(setclientid, 0, sizeof(*setclientid));
+
 	if (argp->minorversion >= 1)
 		return nfserr_notsupp;
 
@@ -1355,8 +1384,10 @@
 }
 
 static __be32
-nfsd4_decode_setclientid_confirm(struct nfsd4_compoundargs *argp, struct nfsd4_setclientid_confirm *scd_c)
+nfsd4_decode_setclientid_confirm(struct nfsd4_compoundargs *argp,
+				 union nfsd4_op_u *u)
 {
+	struct nfsd4_setclientid_confirm *scd_c = &u->setclientid_confirm;
 	__be32 status;
 
 	if (argp->minorversion >= 1)
@@ -1370,10 +1401,13 @@
 
 /* Also used for NVERIFY */
 static __be32
-nfsd4_decode_verify(struct nfsd4_compoundargs *argp, struct nfsd4_verify *verify)
+nfsd4_decode_verify(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_verify *verify = &u->verify;
 	__be32 *p, status;
 
+	memset(verify, 0, sizeof(*verify));
+
 	status = nfsd4_decode_bitmap4(argp, verify->ve_bmval,
 				      ARRAY_SIZE(verify->ve_bmval));
 	if (status)
@@ -1395,8 +1429,9 @@
 }
 
 static __be32
-nfsd4_decode_write(struct nfsd4_compoundargs *argp, struct nfsd4_write *write)
+nfsd4_decode_write(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_write *write = &u->write;
 	__be32 status;
 
 	status = nfsd4_decode_stateid4(argp, &write->wr_stateid);
@@ -1413,12 +1448,17 @@
 	if (!xdr_stream_subsegment(argp->xdr, &write->wr_payload, write->wr_buflen))
 		return nfserr_bad_xdr;
 
+	write->wr_bytes_written = 0;
+	write->wr_how_written = 0;
+	memset(&write->wr_verifier, 0, sizeof(write->wr_verifier));
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_release_lockowner(struct nfsd4_compoundargs *argp, struct nfsd4_release_lockowner *rlockowner)
+nfsd4_decode_release_lockowner(struct nfsd4_compoundargs *argp,
+			       union nfsd4_op_u *u)
 {
+	struct nfsd4_release_lockowner *rlockowner = &u->release_lockowner;
 	__be32 status;
 
 	if (argp->minorversion >= 1)
@@ -1435,18 +1475,24 @@
 	return nfs_ok;
 }
 
-static __be32 nfsd4_decode_backchannel_ctl(struct nfsd4_compoundargs *argp, struct nfsd4_backchannel_ctl *bc)
+static __be32 nfsd4_decode_backchannel_ctl(struct nfsd4_compoundargs *argp,
+					   union nfsd4_op_u *u)
 {
+	struct nfsd4_backchannel_ctl *bc = &u->backchannel_ctl;
+	memset(bc, 0, sizeof(*bc));
 	if (xdr_stream_decode_u32(argp->xdr, &bc->bc_cb_program) < 0)
 		return nfserr_bad_xdr;
 	return nfsd4_decode_cb_sec(argp, &bc->bc_cb_sec);
 }
 
-static __be32 nfsd4_decode_bind_conn_to_session(struct nfsd4_compoundargs *argp, struct nfsd4_bind_conn_to_session *bcts)
+static __be32 nfsd4_decode_bind_conn_to_session(struct nfsd4_compoundargs *argp,
+						union nfsd4_op_u *u)
 {
+	struct nfsd4_bind_conn_to_session *bcts = &u->bind_conn_to_session;
 	u32 use_conn_in_rdma_mode;
 	__be32 status;
 
+	memset(bcts, 0, sizeof(*bcts));
 	status = nfsd4_decode_sessionid4(argp, &bcts->sessionid);
 	if (status)
 		return status;
@@ -1584,10 +1630,12 @@
 
 static __be32
 nfsd4_decode_exchange_id(struct nfsd4_compoundargs *argp,
-			 struct nfsd4_exchange_id *exid)
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_exchange_id *exid = &u->exchange_id;
 	__be32 status;
 
+	memset(exid, 0, sizeof(*exid));
 	status = nfsd4_decode_verifier4(argp, &exid->verifier);
 	if (status)
 		return status;
@@ -1636,10 +1684,12 @@
 
 static __be32
 nfsd4_decode_create_session(struct nfsd4_compoundargs *argp,
-			    struct nfsd4_create_session *sess)
+			    union nfsd4_op_u *u)
 {
+	struct nfsd4_create_session *sess = &u->create_session;
 	__be32 status;
 
+	memset(sess, 0, sizeof(*sess));
 	status = nfsd4_decode_clientid4(argp, &sess->clientid);
 	if (status)
 		return status;
@@ -1655,34 +1705,34 @@
 		return status;
 	if (xdr_stream_decode_u32(argp->xdr, &sess->callback_prog) < 0)
 		return nfserr_bad_xdr;
-	status = nfsd4_decode_cb_sec(argp, &sess->cb_sec);
-	if (status)
-		return status;
-
-	return nfs_ok;
+	return nfsd4_decode_cb_sec(argp, &sess->cb_sec);
 }
 
 static __be32
 nfsd4_decode_destroy_session(struct nfsd4_compoundargs *argp,
-			     struct nfsd4_destroy_session *destroy_session)
+			     union nfsd4_op_u *u)
 {
+	struct nfsd4_destroy_session *destroy_session = &u->destroy_session;
 	return nfsd4_decode_sessionid4(argp, &destroy_session->sessionid);
 }
 
 static __be32
 nfsd4_decode_free_stateid(struct nfsd4_compoundargs *argp,
-			  struct nfsd4_free_stateid *free_stateid)
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_free_stateid *free_stateid = &u->free_stateid;
 	return nfsd4_decode_stateid4(argp, &free_stateid->fr_stateid);
 }
 
 #ifdef CONFIG_NFSD_PNFS
 static __be32
 nfsd4_decode_getdeviceinfo(struct nfsd4_compoundargs *argp,
-		struct nfsd4_getdeviceinfo *gdev)
+		union nfsd4_op_u *u)
 {
+	struct nfsd4_getdeviceinfo *gdev = &u->getdeviceinfo;
 	__be32 status;
 
+	memset(gdev, 0, sizeof(*gdev));
 	status = nfsd4_decode_deviceid4(argp, &gdev->gd_devid);
 	if (status)
 		return status;
@@ -1699,10 +1749,12 @@
 
 static __be32
 nfsd4_decode_layoutcommit(struct nfsd4_compoundargs *argp,
-			  struct nfsd4_layoutcommit *lcp)
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_layoutcommit *lcp = &u->layoutcommit;
 	__be32 *p, status;
 
+	memset(lcp, 0, sizeof(*lcp));
 	if (xdr_stream_decode_u64(argp->xdr, &lcp->lc_seg.offset) < 0)
 		return nfserr_bad_xdr;
 	if (xdr_stream_decode_u64(argp->xdr, &lcp->lc_seg.length) < 0)
@@ -1734,10 +1786,12 @@
 
 static __be32
 nfsd4_decode_layoutget(struct nfsd4_compoundargs *argp,
-		struct nfsd4_layoutget *lgp)
+		union nfsd4_op_u *u)
 {
+	struct nfsd4_layoutget *lgp = &u->layoutget;
 	__be32 status;
 
+	memset(lgp, 0, sizeof(*lgp));
 	if (xdr_stream_decode_u32(argp->xdr, &lgp->lg_signal) < 0)
 		return nfserr_bad_xdr;
 	if (xdr_stream_decode_u32(argp->xdr, &lgp->lg_layout_type) < 0)
@@ -1761,8 +1815,10 @@
 
 static __be32
 nfsd4_decode_layoutreturn(struct nfsd4_compoundargs *argp,
-		struct nfsd4_layoutreturn *lrp)
+		union nfsd4_op_u *u)
 {
+	struct nfsd4_layoutreturn *lrp = &u->layoutreturn;
+	memset(lrp, 0, sizeof(*lrp));
 	if (xdr_stream_decode_bool(argp->xdr, &lrp->lr_reclaim) < 0)
 		return nfserr_bad_xdr;
 	if (xdr_stream_decode_u32(argp->xdr, &lrp->lr_layout_type) < 0)
@@ -1774,17 +1830,21 @@
 #endif /* CONFIG_NFSD_PNFS */
 
 static __be32 nfsd4_decode_secinfo_no_name(struct nfsd4_compoundargs *argp,
-					   struct nfsd4_secinfo_no_name *sin)
+					   union nfsd4_op_u *u)
 {
+	struct nfsd4_secinfo_no_name *sin = &u->secinfo_no_name;
 	if (xdr_stream_decode_u32(argp->xdr, &sin->sin_style) < 0)
 		return nfserr_bad_xdr;
+
+	sin->sin_exp = NULL;
 	return nfs_ok;
 }
 
 static __be32
 nfsd4_decode_sequence(struct nfsd4_compoundargs *argp,
-		      struct nfsd4_sequence *seq)
+		      union nfsd4_op_u *u)
 {
+	struct nfsd4_sequence *seq = &u->sequence;
 	__be32 *p, status;
 
 	status = nfsd4_decode_sessionid4(argp, &seq->sessionid);
@@ -1798,16 +1858,20 @@
 	seq->maxslots = be32_to_cpup(p++);
 	seq->cachethis = be32_to_cpup(p);
 
+	seq->status_flags = 0;
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_test_stateid(struct nfsd4_compoundargs *argp, struct nfsd4_test_stateid *test_stateid)
+nfsd4_decode_test_stateid(struct nfsd4_compoundargs *argp,
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_test_stateid *test_stateid = &u->test_stateid;
 	struct nfsd4_test_stateid_id *stateid;
 	__be32 status;
 	u32 i;
 
+	memset(test_stateid, 0, sizeof(*test_stateid));
 	if (xdr_stream_decode_u32(argp->xdr, &test_stateid->ts_num_ids) < 0)
 		return nfserr_bad_xdr;
 
@@ -1815,7 +1879,7 @@
 	for (i = 0; i < test_stateid->ts_num_ids; i++) {
 		stateid = svcxdr_tmpalloc(argp, sizeof(*stateid));
 		if (!stateid)
-			return nfserrno(-ENOMEM);	/* XXX: not jukebox? */
+			return nfserr_jukebox;
 		INIT_LIST_HEAD(&stateid->ts_id_list);
 		list_add_tail(&stateid->ts_id_list, &test_stateid->ts_stateid_list);
 		status = nfsd4_decode_stateid4(argp, &stateid->ts_id_stateid);
@@ -1827,14 +1891,16 @@
 }
 
 static __be32 nfsd4_decode_destroy_clientid(struct nfsd4_compoundargs *argp,
-					    struct nfsd4_destroy_clientid *dc)
+					    union nfsd4_op_u *u)
 {
+	struct nfsd4_destroy_clientid *dc = &u->destroy_clientid;
 	return nfsd4_decode_clientid4(argp, &dc->clientid);
 }
 
 static __be32 nfsd4_decode_reclaim_complete(struct nfsd4_compoundargs *argp,
-					    struct nfsd4_reclaim_complete *rc)
+					    union nfsd4_op_u *u)
 {
+	struct nfsd4_reclaim_complete *rc = &u->reclaim_complete;
 	if (xdr_stream_decode_bool(argp->xdr, &rc->rca_one_fs) < 0)
 		return nfserr_bad_xdr;
 	return nfs_ok;
@@ -1842,8 +1908,9 @@
 
 static __be32
 nfsd4_decode_fallocate(struct nfsd4_compoundargs *argp,
-		       struct nfsd4_fallocate *fallocate)
+		       union nfsd4_op_u *u)
 {
+	struct nfsd4_fallocate *fallocate = &u->allocate;
 	__be32 status;
 
 	status = nfsd4_decode_stateid4(argp, &fallocate->falloc_stateid);
@@ -1899,12 +1966,14 @@
 }
 
 static __be32
-nfsd4_decode_copy(struct nfsd4_compoundargs *argp, struct nfsd4_copy *copy)
+nfsd4_decode_copy(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_copy *copy = &u->copy;
+	u32 consecutive, i, count, sync;
 	struct nl4_server *ns_dummy;
-	u32 consecutive, i, count;
 	__be32 status;
 
+	memset(copy, 0, sizeof(*copy));
 	status = nfsd4_decode_stateid4(argp, &copy->cp_src_stateid);
 	if (status)
 		return status;
@@ -1920,25 +1989,28 @@
 	/* ca_consecutive: we always do consecutive copies */
 	if (xdr_stream_decode_u32(argp->xdr, &consecutive) < 0)
 		return nfserr_bad_xdr;
-	if (xdr_stream_decode_u32(argp->xdr, &copy->cp_synchronous) < 0)
+	if (xdr_stream_decode_bool(argp->xdr, &sync) < 0)
 		return nfserr_bad_xdr;
+	nfsd4_copy_set_sync(copy, sync);
 
 	if (xdr_stream_decode_u32(argp->xdr, &count) < 0)
 		return nfserr_bad_xdr;
-	copy->cp_intra = false;
+	copy->cp_src = svcxdr_tmpalloc(argp, sizeof(*copy->cp_src));
+	if (copy->cp_src == NULL)
+		return nfserr_jukebox;
 	if (count == 0) { /* intra-server copy */
-		copy->cp_intra = true;
+		__set_bit(NFSD4_COPY_F_INTRA, &copy->cp_flags);
 		return nfs_ok;
 	}
 
 	/* decode all the supplied server addresses but use only the first */
-	status = nfsd4_decode_nl4_server(argp, &copy->cp_src);
+	status = nfsd4_decode_nl4_server(argp, copy->cp_src);
 	if (status)
 		return status;
 
 	ns_dummy = kmalloc(sizeof(struct nl4_server), GFP_KERNEL);
 	if (ns_dummy == NULL)
-		return nfserrno(-ENOMEM);	/* XXX: jukebox? */
+		return nfserr_jukebox;
 	for (i = 0; i < count - 1; i++) {
 		status = nfsd4_decode_nl4_server(argp, ns_dummy);
 		if (status) {
@@ -1953,26 +2025,39 @@
 
 static __be32
 nfsd4_decode_copy_notify(struct nfsd4_compoundargs *argp,
-			 struct nfsd4_copy_notify *cn)
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_copy_notify *cn = &u->copy_notify;
 	__be32 status;
 
+	memset(cn, 0, sizeof(*cn));
+	cn->cpn_src = svcxdr_tmpalloc(argp, sizeof(*cn->cpn_src));
+	if (cn->cpn_src == NULL)
+		return nfserr_jukebox;
+	cn->cpn_dst = svcxdr_tmpalloc(argp, sizeof(*cn->cpn_dst));
+	if (cn->cpn_dst == NULL)
+		return nfserr_jukebox;
+
 	status = nfsd4_decode_stateid4(argp, &cn->cpn_src_stateid);
 	if (status)
 		return status;
-	return nfsd4_decode_nl4_server(argp, &cn->cpn_dst);
+	return nfsd4_decode_nl4_server(argp, cn->cpn_dst);
 }
 
 static __be32
 nfsd4_decode_offload_status(struct nfsd4_compoundargs *argp,
-			    struct nfsd4_offload_status *os)
+			    union nfsd4_op_u *u)
 {
+	struct nfsd4_offload_status *os = &u->offload_status;
+	os->count = 0;
+	os->status = 0;
 	return nfsd4_decode_stateid4(argp, &os->stateid);
 }
 
 static __be32
-nfsd4_decode_seek(struct nfsd4_compoundargs *argp, struct nfsd4_seek *seek)
+nfsd4_decode_seek(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_seek *seek = &u->seek;
 	__be32 status;
 
 	status = nfsd4_decode_stateid4(argp, &seek->seek_stateid);
@@ -1983,12 +2068,15 @@
 	if (xdr_stream_decode_u32(argp->xdr, &seek->seek_whence) < 0)
 		return nfserr_bad_xdr;
 
+	seek->seek_eof = 0;
+	seek->seek_pos = 0;
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_clone(struct nfsd4_compoundargs *argp, struct nfsd4_clone *clone)
+nfsd4_decode_clone(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u)
 {
+	struct nfsd4_clone *clone = &u->clone;
 	__be32 status;
 
 	status = nfsd4_decode_stateid4(argp, &clone->cl_src_stateid);
@@ -2113,11 +2201,13 @@
  */
 static __be32
 nfsd4_decode_getxattr(struct nfsd4_compoundargs *argp,
-		      struct nfsd4_getxattr *getxattr)
+		      union nfsd4_op_u *u)
 {
+	struct nfsd4_getxattr *getxattr = &u->getxattr;
 	__be32 status;
 	u32 maxcount;
 
+	memset(getxattr, 0, sizeof(*getxattr));
 	status = nfsd4_decode_xattr_name(argp, &getxattr->getxa_name);
 	if (status)
 		return status;
@@ -2126,17 +2216,19 @@
 	maxcount = min_t(u32, XATTR_SIZE_MAX, maxcount);
 
 	getxattr->getxa_len = maxcount;
-
-	return status;
+	return nfs_ok;
 }
 
 static __be32
 nfsd4_decode_setxattr(struct nfsd4_compoundargs *argp,
-		      struct nfsd4_setxattr *setxattr)
+		      union nfsd4_op_u *u)
 {
+	struct nfsd4_setxattr *setxattr = &u->setxattr;
 	u32 flags, maxcount, size;
 	__be32 status;
 
+	memset(setxattr, 0, sizeof(*setxattr));
+
 	if (xdr_stream_decode_u32(argp->xdr, &flags) < 0)
 		return nfserr_bad_xdr;
 
@@ -2171,10 +2263,13 @@
 
 static __be32
 nfsd4_decode_listxattrs(struct nfsd4_compoundargs *argp,
-			struct nfsd4_listxattrs *listxattrs)
+			union nfsd4_op_u *u)
 {
+	struct nfsd4_listxattrs *listxattrs = &u->listxattrs;
 	u32 maxcount;
 
+	memset(listxattrs, 0, sizeof(*listxattrs));
+
 	if (xdr_stream_decode_u64(argp->xdr, &listxattrs->lsxa_cookie) < 0)
 		return nfserr_bad_xdr;
 
@@ -2200,112 +2295,114 @@
 
 static __be32
 nfsd4_decode_removexattr(struct nfsd4_compoundargs *argp,
-			 struct nfsd4_removexattr *removexattr)
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_removexattr *removexattr = &u->removexattr;
+	memset(removexattr, 0, sizeof(*removexattr));
 	return nfsd4_decode_xattr_name(argp, &removexattr->rmxa_name);
 }
 
 static __be32
-nfsd4_decode_noop(struct nfsd4_compoundargs *argp, void *p)
+nfsd4_decode_noop(struct nfsd4_compoundargs *argp, union nfsd4_op_u *p)
 {
 	return nfs_ok;
 }
 
 static __be32
-nfsd4_decode_notsupp(struct nfsd4_compoundargs *argp, void *p)
+nfsd4_decode_notsupp(struct nfsd4_compoundargs *argp, union nfsd4_op_u *p)
 {
 	return nfserr_notsupp;
 }
 
-typedef __be32(*nfsd4_dec)(struct nfsd4_compoundargs *argp, void *);
+typedef __be32(*nfsd4_dec)(struct nfsd4_compoundargs *argp, union nfsd4_op_u *u);
 
 static const nfsd4_dec nfsd4_dec_ops[] = {
-	[OP_ACCESS]		= (nfsd4_dec)nfsd4_decode_access,
-	[OP_CLOSE]		= (nfsd4_dec)nfsd4_decode_close,
-	[OP_COMMIT]		= (nfsd4_dec)nfsd4_decode_commit,
-	[OP_CREATE]		= (nfsd4_dec)nfsd4_decode_create,
-	[OP_DELEGPURGE]		= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_DELEGRETURN]	= (nfsd4_dec)nfsd4_decode_delegreturn,
-	[OP_GETATTR]		= (nfsd4_dec)nfsd4_decode_getattr,
-	[OP_GETFH]		= (nfsd4_dec)nfsd4_decode_noop,
-	[OP_LINK]		= (nfsd4_dec)nfsd4_decode_link,
-	[OP_LOCK]		= (nfsd4_dec)nfsd4_decode_lock,
-	[OP_LOCKT]		= (nfsd4_dec)nfsd4_decode_lockt,
-	[OP_LOCKU]		= (nfsd4_dec)nfsd4_decode_locku,
-	[OP_LOOKUP]		= (nfsd4_dec)nfsd4_decode_lookup,
-	[OP_LOOKUPP]		= (nfsd4_dec)nfsd4_decode_noop,
-	[OP_NVERIFY]		= (nfsd4_dec)nfsd4_decode_verify,
-	[OP_OPEN]		= (nfsd4_dec)nfsd4_decode_open,
-	[OP_OPENATTR]		= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_OPEN_CONFIRM]	= (nfsd4_dec)nfsd4_decode_open_confirm,
-	[OP_OPEN_DOWNGRADE]	= (nfsd4_dec)nfsd4_decode_open_downgrade,
-	[OP_PUTFH]		= (nfsd4_dec)nfsd4_decode_putfh,
-	[OP_PUTPUBFH]		= (nfsd4_dec)nfsd4_decode_putpubfh,
-	[OP_PUTROOTFH]		= (nfsd4_dec)nfsd4_decode_noop,
-	[OP_READ]		= (nfsd4_dec)nfsd4_decode_read,
-	[OP_READDIR]		= (nfsd4_dec)nfsd4_decode_readdir,
-	[OP_READLINK]		= (nfsd4_dec)nfsd4_decode_noop,
-	[OP_REMOVE]		= (nfsd4_dec)nfsd4_decode_remove,
-	[OP_RENAME]		= (nfsd4_dec)nfsd4_decode_rename,
-	[OP_RENEW]		= (nfsd4_dec)nfsd4_decode_renew,
-	[OP_RESTOREFH]		= (nfsd4_dec)nfsd4_decode_noop,
-	[OP_SAVEFH]		= (nfsd4_dec)nfsd4_decode_noop,
-	[OP_SECINFO]		= (nfsd4_dec)nfsd4_decode_secinfo,
-	[OP_SETATTR]		= (nfsd4_dec)nfsd4_decode_setattr,
-	[OP_SETCLIENTID]	= (nfsd4_dec)nfsd4_decode_setclientid,
-	[OP_SETCLIENTID_CONFIRM] = (nfsd4_dec)nfsd4_decode_setclientid_confirm,
-	[OP_VERIFY]		= (nfsd4_dec)nfsd4_decode_verify,
-	[OP_WRITE]		= (nfsd4_dec)nfsd4_decode_write,
-	[OP_RELEASE_LOCKOWNER]	= (nfsd4_dec)nfsd4_decode_release_lockowner,
+	[OP_ACCESS]		= nfsd4_decode_access,
+	[OP_CLOSE]		= nfsd4_decode_close,
+	[OP_COMMIT]		= nfsd4_decode_commit,
+	[OP_CREATE]		= nfsd4_decode_create,
+	[OP_DELEGPURGE]		= nfsd4_decode_notsupp,
+	[OP_DELEGRETURN]	= nfsd4_decode_delegreturn,
+	[OP_GETATTR]		= nfsd4_decode_getattr,
+	[OP_GETFH]		= nfsd4_decode_noop,
+	[OP_LINK]		= nfsd4_decode_link,
+	[OP_LOCK]		= nfsd4_decode_lock,
+	[OP_LOCKT]		= nfsd4_decode_lockt,
+	[OP_LOCKU]		= nfsd4_decode_locku,
+	[OP_LOOKUP]		= nfsd4_decode_lookup,
+	[OP_LOOKUPP]		= nfsd4_decode_noop,
+	[OP_NVERIFY]		= nfsd4_decode_verify,
+	[OP_OPEN]		= nfsd4_decode_open,
+	[OP_OPENATTR]		= nfsd4_decode_notsupp,
+	[OP_OPEN_CONFIRM]	= nfsd4_decode_open_confirm,
+	[OP_OPEN_DOWNGRADE]	= nfsd4_decode_open_downgrade,
+	[OP_PUTFH]		= nfsd4_decode_putfh,
+	[OP_PUTPUBFH]		= nfsd4_decode_noop,
+	[OP_PUTROOTFH]		= nfsd4_decode_noop,
+	[OP_READ]		= nfsd4_decode_read,
+	[OP_READDIR]		= nfsd4_decode_readdir,
+	[OP_READLINK]		= nfsd4_decode_noop,
+	[OP_REMOVE]		= nfsd4_decode_remove,
+	[OP_RENAME]		= nfsd4_decode_rename,
+	[OP_RENEW]		= nfsd4_decode_renew,
+	[OP_RESTOREFH]		= nfsd4_decode_noop,
+	[OP_SAVEFH]		= nfsd4_decode_noop,
+	[OP_SECINFO]		= nfsd4_decode_secinfo,
+	[OP_SETATTR]		= nfsd4_decode_setattr,
+	[OP_SETCLIENTID]	= nfsd4_decode_setclientid,
+	[OP_SETCLIENTID_CONFIRM] = nfsd4_decode_setclientid_confirm,
+	[OP_VERIFY]		= nfsd4_decode_verify,
+	[OP_WRITE]		= nfsd4_decode_write,
+	[OP_RELEASE_LOCKOWNER]	= nfsd4_decode_release_lockowner,
 
 	/* new operations for NFSv4.1 */
-	[OP_BACKCHANNEL_CTL]	= (nfsd4_dec)nfsd4_decode_backchannel_ctl,
-	[OP_BIND_CONN_TO_SESSION]= (nfsd4_dec)nfsd4_decode_bind_conn_to_session,
-	[OP_EXCHANGE_ID]	= (nfsd4_dec)nfsd4_decode_exchange_id,
-	[OP_CREATE_SESSION]	= (nfsd4_dec)nfsd4_decode_create_session,
-	[OP_DESTROY_SESSION]	= (nfsd4_dec)nfsd4_decode_destroy_session,
-	[OP_FREE_STATEID]	= (nfsd4_dec)nfsd4_decode_free_stateid,
-	[OP_GET_DIR_DELEGATION]	= (nfsd4_dec)nfsd4_decode_notsupp,
+	[OP_BACKCHANNEL_CTL]	= nfsd4_decode_backchannel_ctl,
+	[OP_BIND_CONN_TO_SESSION] = nfsd4_decode_bind_conn_to_session,
+	[OP_EXCHANGE_ID]	= nfsd4_decode_exchange_id,
+	[OP_CREATE_SESSION]	= nfsd4_decode_create_session,
+	[OP_DESTROY_SESSION]	= nfsd4_decode_destroy_session,
+	[OP_FREE_STATEID]	= nfsd4_decode_free_stateid,
+	[OP_GET_DIR_DELEGATION]	= nfsd4_decode_notsupp,
 #ifdef CONFIG_NFSD_PNFS
-	[OP_GETDEVICEINFO]	= (nfsd4_dec)nfsd4_decode_getdeviceinfo,
-	[OP_GETDEVICELIST]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_LAYOUTCOMMIT]	= (nfsd4_dec)nfsd4_decode_layoutcommit,
-	[OP_LAYOUTGET]		= (nfsd4_dec)nfsd4_decode_layoutget,
-	[OP_LAYOUTRETURN]	= (nfsd4_dec)nfsd4_decode_layoutreturn,
+	[OP_GETDEVICEINFO]	= nfsd4_decode_getdeviceinfo,
+	[OP_GETDEVICELIST]	= nfsd4_decode_notsupp,
+	[OP_LAYOUTCOMMIT]	= nfsd4_decode_layoutcommit,
+	[OP_LAYOUTGET]		= nfsd4_decode_layoutget,
+	[OP_LAYOUTRETURN]	= nfsd4_decode_layoutreturn,
 #else
-	[OP_GETDEVICEINFO]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_GETDEVICELIST]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_LAYOUTCOMMIT]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_LAYOUTGET]		= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_LAYOUTRETURN]	= (nfsd4_dec)nfsd4_decode_notsupp,
+	[OP_GETDEVICEINFO]	= nfsd4_decode_notsupp,
+	[OP_GETDEVICELIST]	= nfsd4_decode_notsupp,
+	[OP_LAYOUTCOMMIT]	= nfsd4_decode_notsupp,
+	[OP_LAYOUTGET]		= nfsd4_decode_notsupp,
+	[OP_LAYOUTRETURN]	= nfsd4_decode_notsupp,
 #endif
-	[OP_SECINFO_NO_NAME]	= (nfsd4_dec)nfsd4_decode_secinfo_no_name,
-	[OP_SEQUENCE]		= (nfsd4_dec)nfsd4_decode_sequence,
-	[OP_SET_SSV]		= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_TEST_STATEID]	= (nfsd4_dec)nfsd4_decode_test_stateid,
-	[OP_WANT_DELEGATION]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_DESTROY_CLIENTID]	= (nfsd4_dec)nfsd4_decode_destroy_clientid,
-	[OP_RECLAIM_COMPLETE]	= (nfsd4_dec)nfsd4_decode_reclaim_complete,
+	[OP_SECINFO_NO_NAME]	= nfsd4_decode_secinfo_no_name,
+	[OP_SEQUENCE]		= nfsd4_decode_sequence,
+	[OP_SET_SSV]		= nfsd4_decode_notsupp,
+	[OP_TEST_STATEID]	= nfsd4_decode_test_stateid,
+	[OP_WANT_DELEGATION]	= nfsd4_decode_notsupp,
+	[OP_DESTROY_CLIENTID]	= nfsd4_decode_destroy_clientid,
+	[OP_RECLAIM_COMPLETE]	= nfsd4_decode_reclaim_complete,
 
 	/* new operations for NFSv4.2 */
-	[OP_ALLOCATE]		= (nfsd4_dec)nfsd4_decode_fallocate,
-	[OP_COPY]		= (nfsd4_dec)nfsd4_decode_copy,
-	[OP_COPY_NOTIFY]	= (nfsd4_dec)nfsd4_decode_copy_notify,
-	[OP_DEALLOCATE]		= (nfsd4_dec)nfsd4_decode_fallocate,
-	[OP_IO_ADVISE]		= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_LAYOUTERROR]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_LAYOUTSTATS]	= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_OFFLOAD_CANCEL]	= (nfsd4_dec)nfsd4_decode_offload_status,
-	[OP_OFFLOAD_STATUS]	= (nfsd4_dec)nfsd4_decode_offload_status,
-	[OP_READ_PLUS]		= (nfsd4_dec)nfsd4_decode_read,
-	[OP_SEEK]		= (nfsd4_dec)nfsd4_decode_seek,
-	[OP_WRITE_SAME]		= (nfsd4_dec)nfsd4_decode_notsupp,
-	[OP_CLONE]		= (nfsd4_dec)nfsd4_decode_clone,
+	[OP_ALLOCATE]		= nfsd4_decode_fallocate,
+	[OP_COPY]		= nfsd4_decode_copy,
+	[OP_COPY_NOTIFY]	= nfsd4_decode_copy_notify,
+	[OP_DEALLOCATE]		= nfsd4_decode_fallocate,
+	[OP_IO_ADVISE]		= nfsd4_decode_notsupp,
+	[OP_LAYOUTERROR]	= nfsd4_decode_notsupp,
+	[OP_LAYOUTSTATS]	= nfsd4_decode_notsupp,
+	[OP_OFFLOAD_CANCEL]	= nfsd4_decode_offload_status,
+	[OP_OFFLOAD_STATUS]	= nfsd4_decode_offload_status,
+	[OP_READ_PLUS]		= nfsd4_decode_read,
+	[OP_SEEK]		= nfsd4_decode_seek,
+	[OP_WRITE_SAME]		= nfsd4_decode_notsupp,
+	[OP_CLONE]		= nfsd4_decode_clone,
 	/* RFC 8276 extended atributes operations */
-	[OP_GETXATTR]		= (nfsd4_dec)nfsd4_decode_getxattr,
-	[OP_SETXATTR]		= (nfsd4_dec)nfsd4_decode_setxattr,
-	[OP_LISTXATTRS]		= (nfsd4_dec)nfsd4_decode_listxattrs,
-	[OP_REMOVEXATTR]	= (nfsd4_dec)nfsd4_decode_removexattr,
+	[OP_GETXATTR]		= nfsd4_decode_getxattr,
+	[OP_SETXATTR]		= nfsd4_decode_setxattr,
+	[OP_LISTXATTRS]		= nfsd4_decode_listxattrs,
+	[OP_REMOVEXATTR]	= nfsd4_decode_removexattr,
 };
 
 static inline bool
@@ -2322,7 +2419,7 @@
 	return true;
 }
 
-static int
+static bool
 nfsd4_decode_compound(struct nfsd4_compoundargs *argp)
 {
 	struct nfsd4_op *op;
@@ -2335,40 +2432,34 @@
 	int i;
 
 	if (xdr_stream_decode_u32(argp->xdr, &argp->taglen) < 0)
-		return 0;
+		return false;
 	max_reply += XDR_UNIT;
 	argp->tag = NULL;
 	if (unlikely(argp->taglen)) {
 		if (argp->taglen > NFSD4_MAX_TAGLEN)
-			return 0;
+			return false;
 		p = xdr_inline_decode(argp->xdr, argp->taglen);
 		if (!p)
-			return 0;
+			return false;
 		argp->tag = svcxdr_savemem(argp, p, argp->taglen);
 		if (!argp->tag)
-			return 0;
+			return false;
 		max_reply += xdr_align_size(argp->taglen);
 	}
 
 	if (xdr_stream_decode_u32(argp->xdr, &argp->minorversion) < 0)
-		return 0;
-	if (xdr_stream_decode_u32(argp->xdr, &argp->opcnt) < 0)
-		return 0;
+		return false;
+	if (xdr_stream_decode_u32(argp->xdr, &argp->client_opcnt) < 0)
+		return false;
 
-	/*
-	 * NFS4ERR_RESOURCE is a more helpful error than GARBAGE_ARGS
-	 * here, so we return success at the xdr level so that
-	 * nfsd4_proc can handle this is an NFS-level error.
-	 */
-	if (argp->opcnt > NFSD_MAX_OPS_PER_COMPOUND)
-		return 1;
+	argp->opcnt = min_t(u32, argp->client_opcnt,
+			    NFSD_MAX_OPS_PER_COMPOUND);
 
 	if (argp->opcnt > ARRAY_SIZE(argp->iops)) {
-		argp->ops = kzalloc(argp->opcnt * sizeof(*argp->ops), GFP_KERNEL);
+		argp->ops = vcalloc(argp->opcnt, sizeof(*argp->ops));
 		if (!argp->ops) {
 			argp->ops = argp->iops;
-			dprintk("nfsd: couldn't allocate room for COMPOUND\n");
-			return 0;
+			return false;
 		}
 	}
 
@@ -2378,10 +2469,12 @@
 	for (i = 0; i < argp->opcnt; i++) {
 		op = &argp->ops[i];
 		op->replay = NULL;
+		op->opdesc = NULL;
 
 		if (xdr_stream_decode_u32(argp->xdr, &op->opnum) < 0)
-			return 0;
+			return false;
 		if (nfsd4_opnum_in_range(argp, op)) {
+			op->opdesc = OPDESC(op);
 			op->status = nfsd4_dec_ops[op->opnum](argp, &op->u);
 			if (op->status != nfs_ok)
 				trace_nfsd_compound_decode_err(argp->rqstp,
@@ -2392,7 +2485,7 @@
 			op->opnum = OP_ILLEGAL;
 			op->status = nfserr_op_illegal;
 		}
-		op->opdesc = OPDESC(op);
+
 		/*
 		 * We'll try to cache the result in the DRC if any one
 		 * op in the compound wants to be cached:
@@ -2427,7 +2520,7 @@
 	if (readcount > 1 || max_reply > PAGE_SIZE - auth_slack)
 		clear_bit(RQ_SPLICE_OK, &argp->rqstp->rq_flags);
 
-	return 1;
+	return true;
 }
 
 static __be32 *encode_change(__be32 *p, struct kstat *stat, struct inode *inode,
@@ -2441,6 +2534,20 @@
 	return p;
 }
 
+static __be32 nfsd4_encode_nfstime4(struct xdr_stream *xdr,
+				    struct timespec64 *tv)
+{
+	__be32 *p;
+
+	p = xdr_reserve_space(xdr, XDR_UNIT * 3);
+	if (!p)
+		return nfserr_resource;
+
+	p = xdr_encode_hyper(p, (s64)tv->tv_sec);
+	*p = cpu_to_be32(tv->tv_nsec);
+	return nfs_ok;
+}
+
 /*
  * ctime (in NFSv4, time_metadata) is not writeable, and the client
  * doesn't really care what resolution could theoretically be stored by
@@ -2727,11 +2834,11 @@
 #ifdef CONFIG_NFSD_V4_SECURITY_LABEL
 static inline __be32
 nfsd4_encode_security_label(struct xdr_stream *xdr, struct svc_rqst *rqstp,
-			    void *context, int len)
+			    struct lsmcontext *context)
 {
 	__be32 *p;
 
-	p = xdr_reserve_space(xdr, len + 4 + 4 + 4);
+	p = xdr_reserve_space(xdr, context->len + 4 + 4 + 4);
 	if (!p)
 		return nfserr_resource;
 
@@ -2741,13 +2848,13 @@
 	 */
 	*p++ = cpu_to_be32(0); /* lfs */
 	*p++ = cpu_to_be32(0); /* pi */
-	p = xdr_encode_opaque(p, context, len);
+	p = xdr_encode_opaque(p, context->context, context->len);
 	return 0;
 }
 #else
 static inline __be32
 nfsd4_encode_security_label(struct xdr_stream *xdr, struct svc_rqst *rqstp,
-			    void *context, int len)
+			    struct lsmcontext *context)
 { return 0; }
 #endif
 
@@ -2769,9 +2876,10 @@
 }
 
 
-static int get_parent_attributes(struct svc_export *exp, struct kstat *stat)
+static int nfsd4_get_mounted_on_ino(struct svc_export *exp, u64 *pino)
 {
 	struct path path = exp->ex_path;
+	struct kstat stat;
 	int err;
 
 	path_get(&path);
@@ -2779,8 +2887,10 @@
 		if (path.dentry != path.mnt->mnt_root)
 			break;
 	}
-	err = vfs_getattr(&path, stat, STATX_BASIC_STATS, AT_STATX_SYNC_AS_STAT);
+	err = vfs_getattr(&path, &stat, STATX_INO, AT_STATX_SYNC_AS_STAT);
 	path_put(&path);
+	if (!err)
+		*pino = stat.ino;
 	return err;
 }
 
@@ -2833,10 +2943,9 @@
 	struct kstat stat;
 	struct svc_fh *tempfh = NULL;
 	struct kstatfs statfs;
-	__be32 *p;
+	__be32 *p, *attrlen_p;
 	int starting_len = xdr->buf->len;
 	int attrlen_offset;
-	__be32 attrlen;
 	u32 dummy;
 	u64 dummy64;
 	u32 rdattr_err = 0;
@@ -2844,8 +2953,7 @@
 	int err;
 	struct nfs4_acl *acl = NULL;
 #ifdef CONFIG_NFSD_V4_SECURITY_LABEL
-	void *context = NULL;
-	int contextlen;
+	struct lsmcontext context = { };
 #endif
 	bool contextsupport = false;
 	struct nfsd4_compoundres *resp = rqstp->rq_resp;
@@ -2868,6 +2976,9 @@
 	err = vfs_getattr(&path, &stat, STATX_BASIC_STATS, AT_STATX_SYNC_AS_STAT);
 	if (err)
 		goto out_nfserr;
+	if (!(stat.result_mask & STATX_BTIME))
+		/* underlying FS does not offer btime so we can't share it */
+		bmval1 &= ~FATTR4_WORD1_TIME_CREATE;
 	if ((bmval0 & (FATTR4_WORD0_FILES_AVAIL | FATTR4_WORD0_FILES_FREE |
 			FATTR4_WORD0_FILES_TOTAL | FATTR4_WORD0_MAXNAME)) ||
 	    (bmval1 & (FATTR4_WORD1_SPACE_AVAIL | FATTR4_WORD1_SPACE_FREE |
@@ -2903,7 +3014,7 @@
 	     bmval0 & FATTR4_WORD0_SUPPORTED_ATTRS) {
 		if (exp->ex_flags & NFSEXP_SECURITY_LABEL)
 			err = security_inode_getsecctx(d_inode(dentry),
-						&context, &contextlen);
+						       &context);
 		else
 			err = -EOPNOTSUPP;
 		contextsupport = (err == 0);
@@ -2921,10 +3032,9 @@
 		goto out;
 
 	attrlen_offset = xdr->buf->len;
-	p = xdr_reserve_space(xdr, 4);
-	if (!p)
+	attrlen_p = xdr_reserve_space(xdr, XDR_UNIT);
+	if (!attrlen_p)
 		goto out_resource;
-	p++;                /* to be backfilled later */
 
 	if (bmval0 & FATTR4_WORD0_SUPPORTED_ATTRS) {
 		u32 supp[3];
@@ -3110,7 +3220,7 @@
 		p = xdr_reserve_space(xdr, fhp->fh_handle.fh_size + 4);
 		if (!p)
 			goto out_resource;
-		p = xdr_encode_opaque(p, &fhp->fh_handle.fh_base,
+		p = xdr_encode_opaque(p, &fhp->fh_handle.fh_raw,
 					fhp->fh_handle.fh_size);
 	}
 	if (bmval0 & FATTR4_WORD0_FILEID) {
@@ -3242,11 +3352,14 @@
 		p = xdr_encode_hyper(p, dummy64);
 	}
 	if (bmval1 & FATTR4_WORD1_TIME_ACCESS) {
-		p = xdr_reserve_space(xdr, 12);
-		if (!p)
-			goto out_resource;
-		p = xdr_encode_hyper(p, (s64)stat.atime.tv_sec);
-		*p++ = cpu_to_be32(stat.atime.tv_nsec);
+		status = nfsd4_encode_nfstime4(xdr, &stat.atime);
+		if (status)
+			goto out;
+	}
+	if (bmval1 & FATTR4_WORD1_TIME_CREATE) {
+		status = nfsd4_encode_nfstime4(xdr, &stat.btime);
+		if (status)
+			goto out;
 	}
 	if (bmval1 & FATTR4_WORD1_TIME_DELTA) {
 		p = xdr_reserve_space(xdr, 12);
@@ -3255,36 +3368,31 @@
 		p = encode_time_delta(p, d_inode(dentry));
 	}
 	if (bmval1 & FATTR4_WORD1_TIME_METADATA) {
-		p = xdr_reserve_space(xdr, 12);
-		if (!p)
-			goto out_resource;
-		p = xdr_encode_hyper(p, (s64)stat.ctime.tv_sec);
-		*p++ = cpu_to_be32(stat.ctime.tv_nsec);
+		status = nfsd4_encode_nfstime4(xdr, &stat.ctime);
+		if (status)
+			goto out;
 	}
 	if (bmval1 & FATTR4_WORD1_TIME_MODIFY) {
-		p = xdr_reserve_space(xdr, 12);
-		if (!p)
-			goto out_resource;
-		p = xdr_encode_hyper(p, (s64)stat.mtime.tv_sec);
-		*p++ = cpu_to_be32(stat.mtime.tv_nsec);
+		status = nfsd4_encode_nfstime4(xdr, &stat.mtime);
+		if (status)
+			goto out;
 	}
 	if (bmval1 & FATTR4_WORD1_MOUNTED_ON_FILEID) {
-		struct kstat parent_stat;
 		u64 ino = stat.ino;
 
 		p = xdr_reserve_space(xdr, 8);
 		if (!p)
                 	goto out_resource;
 		/*
-		 * Get parent's attributes if not ignoring crossmount
-		 * and this is the root of a cross-mounted filesystem.
+		 * Get ino of mountpoint in parent filesystem, if not ignoring
+		 * crossmount and this is the root of a cross-mounted
+		 * filesystem.
 		 */
 		if (ignore_crossmnt == 0 &&
 		    dentry == exp->ex_path.mnt->mnt_root) {
-			err = get_parent_attributes(exp, &parent_stat);
+			err = nfsd4_get_mounted_on_ino(exp, &ino);
 			if (err)
 				goto out_nfserr;
-			ino = parent_stat.ino;
 		}
 		p = xdr_encode_hyper(p, ino);
 	}
@@ -3323,8 +3431,7 @@
 
 #ifdef CONFIG_NFSD_V4_SECURITY_LABEL
 	if (bmval2 & FATTR4_WORD2_SECURITY_LABEL) {
-		status = nfsd4_encode_security_label(xdr, rqstp, context,
-								contextlen);
+		status = nfsd4_encode_security_label(xdr, rqstp, &context);
 		if (status)
 			goto out;
 	}
@@ -3339,14 +3446,13 @@
 		*p++ = cpu_to_be32(err == 0);
 	}
 
-	attrlen = htonl(xdr->buf->len - attrlen_offset - 4);
-	write_bytes_to_xdr_buf(xdr->buf, attrlen_offset, &attrlen, 4);
+	*attrlen_p = cpu_to_be32(xdr->buf->len - attrlen_offset - XDR_UNIT);
 	status = nfs_ok;
 
 out:
 #ifdef CONFIG_NFSD_V4_SECURITY_LABEL
-	if (context)
-		security_release_secctx(context, contextlen);
+	if (context.context)
+		security_release_secctx(&context);
 #endif /* CONFIG_NFSD_V4_SECURITY_LABEL */
 	kfree(acl);
 	if (tempfh) {
@@ -3509,7 +3615,7 @@
 	p = xdr_reserve_space(xdr, 3*4 + namlen);
 	if (!p)
 		goto fail;
-	p = xdr_encode_hyper(p, NFS_OFFSET_MAX);    /* offset of next entry */
+	p = xdr_encode_hyper(p, OFFSET_MAX);        /* offset of next entry */
 	p = xdr_encode_array(p, name, namlen);      /* name length & name */
 
 	nfserr = nfsd4_encode_dirent_fattr(xdr, cd, name, namlen);
@@ -3522,6 +3628,17 @@
 	case nfserr_noent:
 		xdr_truncate_encode(xdr, start_offset);
 		goto skip_entry;
+	case nfserr_jukebox:
+		/*
+		 * The pseudoroot should only display dentries that lead to
+		 * exports. If we get EJUKEBOX here, then we can't tell whether
+		 * this entry should be included. Just fail the whole READDIR
+		 * with NFS4ERR_DELAY in that case, and hope that the situation
+		 * will resolve itself by the client's next attempt.
+		 */
+		if (cd->rd_fhp->fh_export->ex_flags & NFSEXP_V4ROOT)
+			goto fail;
+		fallthrough;
 	default:
 		/*
 		 * If the client requested the RDATTR_ERROR attribute,
@@ -3582,8 +3699,10 @@
 }
 
 static __be32
-nfsd4_encode_access(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_access *access)
+nfsd4_encode_access(struct nfsd4_compoundres *resp, __be32 nfserr,
+		    union nfsd4_op_u *u)
 {
+	struct nfsd4_access *access = &u->access;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -3595,8 +3714,10 @@
 	return 0;
 }
 
-static __be32 nfsd4_encode_bind_conn_to_session(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_bind_conn_to_session *bcts)
+static __be32 nfsd4_encode_bind_conn_to_session(struct nfsd4_compoundres *resp, __be32 nfserr,
+						union nfsd4_op_u *u)
 {
+	struct nfsd4_bind_conn_to_session *bcts = &u->bind_conn_to_session;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -3612,8 +3733,10 @@
 }
 
 static __be32
-nfsd4_encode_close(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_close *close)
+nfsd4_encode_close(struct nfsd4_compoundres *resp, __be32 nfserr,
+		   union nfsd4_op_u *u)
 {
+	struct nfsd4_close *close = &u->close;
 	struct xdr_stream *xdr = resp->xdr;
 
 	return nfsd4_encode_stateid(xdr, &close->cl_stateid);
@@ -3621,8 +3744,10 @@
 
 
 static __be32
-nfsd4_encode_commit(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_commit *commit)
+nfsd4_encode_commit(struct nfsd4_compoundres *resp, __be32 nfserr,
+		    union nfsd4_op_u *u)
 {
+	struct nfsd4_commit *commit = &u->commit;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -3635,8 +3760,10 @@
 }
 
 static __be32
-nfsd4_encode_create(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_create *create)
+nfsd4_encode_create(struct nfsd4_compoundres *resp, __be32 nfserr,
+		    union nfsd4_op_u *u)
 {
+	struct nfsd4_create *create = &u->create;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -3649,8 +3776,10 @@
 }
 
 static __be32
-nfsd4_encode_getattr(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_getattr *getattr)
+nfsd4_encode_getattr(struct nfsd4_compoundres *resp, __be32 nfserr,
+		     union nfsd4_op_u *u)
 {
+	struct nfsd4_getattr *getattr = &u->getattr;
 	struct svc_fh *fhp = getattr->ga_fhp;
 	struct xdr_stream *xdr = resp->xdr;
 
@@ -3659,8 +3788,10 @@
 }
 
 static __be32
-nfsd4_encode_getfh(struct nfsd4_compoundres *resp, __be32 nfserr, struct svc_fh **fhpp)
+nfsd4_encode_getfh(struct nfsd4_compoundres *resp, __be32 nfserr,
+		   union nfsd4_op_u *u)
 {
+	struct svc_fh **fhpp = &u->getfh;
 	struct xdr_stream *xdr = resp->xdr;
 	struct svc_fh *fhp = *fhpp;
 	unsigned int len;
@@ -3670,7 +3801,7 @@
 	p = xdr_reserve_space(xdr, len + 4);
 	if (!p)
 		return nfserr_resource;
-	p = xdr_encode_opaque(p, &fhp->fh_handle.fh_base, len);
+	p = xdr_encode_opaque(p, &fhp->fh_handle.fh_raw, len);
 	return 0;
 }
 
@@ -3714,8 +3845,10 @@
 }
 
 static __be32
-nfsd4_encode_lock(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_lock *lock)
+nfsd4_encode_lock(struct nfsd4_compoundres *resp, __be32 nfserr,
+		  union nfsd4_op_u *u)
 {
+	struct nfsd4_lock *lock = &u->lock;
 	struct xdr_stream *xdr = resp->xdr;
 
 	if (!nfserr)
@@ -3727,8 +3860,10 @@
 }
 
 static __be32
-nfsd4_encode_lockt(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_lockt *lockt)
+nfsd4_encode_lockt(struct nfsd4_compoundres *resp, __be32 nfserr,
+		   union nfsd4_op_u *u)
 {
+	struct nfsd4_lockt *lockt = &u->lockt;
 	struct xdr_stream *xdr = resp->xdr;
 
 	if (nfserr == nfserr_denied)
@@ -3737,8 +3872,10 @@
 }
 
 static __be32
-nfsd4_encode_locku(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_locku *locku)
+nfsd4_encode_locku(struct nfsd4_compoundres *resp, __be32 nfserr,
+		   union nfsd4_op_u *u)
 {
+	struct nfsd4_locku *locku = &u->locku;
 	struct xdr_stream *xdr = resp->xdr;
 
 	return nfsd4_encode_stateid(xdr, &locku->lu_stateid);
@@ -3746,8 +3883,10 @@
 
 
 static __be32
-nfsd4_encode_link(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_link *link)
+nfsd4_encode_link(struct nfsd4_compoundres *resp, __be32 nfserr,
+		  union nfsd4_op_u *u)
 {
+	struct nfsd4_link *link = &u->link;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -3760,8 +3899,10 @@
 
 
 static __be32
-nfsd4_encode_open(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_open *open)
+nfsd4_encode_open(struct nfsd4_compoundres *resp, __be32 nfserr,
+		  union nfsd4_op_u *u)
 {
+	struct nfsd4_open *open = &u->open;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -3811,7 +3952,7 @@
 		p = xdr_reserve_space(xdr, 32);
 		if (!p)
 			return nfserr_resource;
-		*p++ = cpu_to_be32(0);
+		*p++ = cpu_to_be32(open->op_recall);
 
 		/*
 		 * TODO: space_limit's in delegations
@@ -3854,16 +3995,20 @@
 }
 
 static __be32
-nfsd4_encode_open_confirm(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_open_confirm *oc)
+nfsd4_encode_open_confirm(struct nfsd4_compoundres *resp, __be32 nfserr,
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_open_confirm *oc = &u->open_confirm;
 	struct xdr_stream *xdr = resp->xdr;
 
 	return nfsd4_encode_stateid(xdr, &oc->oc_resp_stateid);
 }
 
 static __be32
-nfsd4_encode_open_downgrade(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_open_downgrade *od)
+nfsd4_encode_open_downgrade(struct nfsd4_compoundres *resp, __be32 nfserr,
+			    union nfsd4_op_u *u)
 {
+	struct nfsd4_open_downgrade *od = &u->open_downgrade;
 	struct xdr_stream *xdr = resp->xdr;
 
 	return nfsd4_encode_stateid(xdr, &od->od_stateid);
@@ -3877,16 +4022,15 @@
 	struct xdr_stream *xdr = resp->xdr;
 	struct xdr_buf *buf = xdr->buf;
 	int status, space_left;
-	u32 eof;
 	__be32 nfserr;
-	__be32 *p = xdr->p - 2;
 
 	/* Make sure there will be room for padding if needed */
 	if (xdr->end - xdr->p < 1)
 		return nfserr_resource;
 
 	nfserr = nfsd_splice_read(read->rd_rqstp, read->rd_fhp,
-				  file, read->rd_offset, &maxcount, &eof);
+				  file, read->rd_offset, &maxcount,
+				  &read->rd_eof);
 	read->rd_length = maxcount;
 	if (nfserr)
 		goto out_err;
@@ -3897,9 +4041,6 @@
 		goto out_err;
 	}
 
-	*(p++) = htonl(eof);
-	*(p++) = htonl(maxcount);
-
 	buf->page_len = maxcount;
 	buf->len += maxcount;
 	xdr->page_ptr += (buf->page_base + maxcount + PAGE_SIZE - 1)
@@ -3941,11 +4082,9 @@
 				 struct file *file, unsigned long maxcount)
 {
 	struct xdr_stream *xdr = resp->xdr;
-	u32 eof;
-	int starting_len = xdr->buf->len - 8;
+	unsigned int starting_len = xdr->buf->len;
+	__be32 zero = xdr_zero;
 	__be32 nfserr;
-	__be32 tmp;
-	int pad;
 
 	read->rd_vlen = xdr_reserve_space_vec(xdr, resp->rqstp->rq_vec, maxcount);
 	if (read->rd_vlen < 0)
@@ -3953,31 +4092,25 @@
 
 	nfserr = nfsd_readv(resp->rqstp, read->rd_fhp, file, read->rd_offset,
 			    resp->rqstp->rq_vec, read->rd_vlen, &maxcount,
-			    &eof);
+			    &read->rd_eof);
 	read->rd_length = maxcount;
 	if (nfserr)
 		return nfserr;
-	if (svc_encode_result_payload(resp->rqstp, starting_len + 8, maxcount))
+	if (svc_encode_result_payload(resp->rqstp, starting_len, maxcount))
 		return nfserr_io;
-	xdr_truncate_encode(xdr, starting_len + 8 + xdr_align_size(maxcount));
-
-	tmp = htonl(eof);
-	write_bytes_to_xdr_buf(xdr->buf, starting_len    , &tmp, 4);
-	tmp = htonl(maxcount);
-	write_bytes_to_xdr_buf(xdr->buf, starting_len + 4, &tmp, 4);
-
-	tmp = xdr_zero;
-	pad = (maxcount&3) ? 4 - (maxcount&3) : 0;
-	write_bytes_to_xdr_buf(xdr->buf, starting_len + 8 + maxcount,
-								&tmp, pad);
-	return 0;
+	xdr_truncate_encode(xdr, starting_len + xdr_align_size(maxcount));
 
+	write_bytes_to_xdr_buf(xdr->buf, starting_len + maxcount, &zero,
+			       xdr_pad_size(maxcount));
+	return nfs_ok;
 }
 
 static __be32
 nfsd4_encode_read(struct nfsd4_compoundres *resp, __be32 nfserr,
-		  struct nfsd4_read *read)
+		  union nfsd4_op_u *u)
 {
+	struct nfsd4_read *read = &u->read;
+	bool splice_ok = test_bit(RQ_SPLICE_OK, &resp->rqstp->rq_flags);
 	unsigned long maxcount;
 	struct xdr_stream *xdr = resp->xdr;
 	struct file *file;
@@ -3990,46 +4123,44 @@
 
 	p = xdr_reserve_space(xdr, 8); /* eof flag and byte count */
 	if (!p) {
-		WARN_ON_ONCE(test_bit(RQ_SPLICE_OK, &resp->rqstp->rq_flags));
+		WARN_ON_ONCE(splice_ok);
 		return nfserr_resource;
 	}
-	if (resp->xdr->buf->page_len &&
-	    test_bit(RQ_SPLICE_OK, &resp->rqstp->rq_flags)) {
+	if (resp->xdr->buf->page_len && splice_ok) {
 		WARN_ON_ONCE(1);
-		return nfserr_resource;
+		return nfserr_serverfault;
 	}
 	xdr_commit_encode(xdr);
 
-	maxcount = svc_max_payload(resp->rqstp);
-	maxcount = min_t(unsigned long, maxcount,
+	maxcount = min_t(unsigned long, read->rd_length,
 			 (xdr->buf->buflen - xdr->buf->len));
-	maxcount = min_t(unsigned long, maxcount, read->rd_length);
 
-	if (file->f_op->splice_read &&
-	    test_bit(RQ_SPLICE_OK, &resp->rqstp->rq_flags))
+	if (file->f_op->splice_read && splice_ok)
 		nfserr = nfsd4_encode_splice_read(resp, read, file, maxcount);
 	else
 		nfserr = nfsd4_encode_readv(resp, read, file, maxcount);
-
-	if (nfserr)
+	if (nfserr) {
 		xdr_truncate_encode(xdr, starting_len);
+		return nfserr;
+	}
 
-	return nfserr;
+	p = xdr_encode_bool(p, read->rd_eof);
+	*p = cpu_to_be32(read->rd_length);
+	return nfs_ok;
 }
 
 static __be32
-nfsd4_encode_readlink(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_readlink *readlink)
+nfsd4_encode_readlink(struct nfsd4_compoundres *resp, __be32 nfserr,
+		      union nfsd4_op_u *u)
 {
-	int maxcount;
-	__be32 wire_count;
-	int zero = 0;
+	struct nfsd4_readlink *readlink = &u->readlink;
+	__be32 *p, *maxcount_p, zero = xdr_zero;
 	struct xdr_stream *xdr = resp->xdr;
 	int length_offset = xdr->buf->len;
-	int status;
-	__be32 *p;
+	int maxcount, status;
 
-	p = xdr_reserve_space(xdr, 4);
-	if (!p)
+	maxcount_p = xdr_reserve_space(xdr, XDR_UNIT);
+	if (!maxcount_p)
 		return nfserr_resource;
 	maxcount = PAGE_SIZE;
 
@@ -4054,14 +4185,11 @@
 		nfserr = nfserrno(status);
 		goto out_err;
 	}
-
-	wire_count = htonl(maxcount);
-	write_bytes_to_xdr_buf(xdr->buf, length_offset, &wire_count, 4);
-	xdr_truncate_encode(xdr, length_offset + 4 + ALIGN(maxcount, 4));
-	if (maxcount & 3)
-		write_bytes_to_xdr_buf(xdr->buf, length_offset + 4 + maxcount,
-						&zero, 4 - (maxcount&3));
-	return 0;
+	*maxcount_p = cpu_to_be32(maxcount);
+	xdr_truncate_encode(xdr, length_offset + 4 + xdr_align_size(maxcount));
+	write_bytes_to_xdr_buf(xdr->buf, length_offset + 4 + maxcount, &zero,
+			       xdr_pad_size(maxcount));
+	return nfs_ok;
 
 out_err:
 	xdr_truncate_encode(xdr, length_offset);
@@ -4069,8 +4197,10 @@
 }
 
 static __be32
-nfsd4_encode_readdir(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_readdir *readdir)
+nfsd4_encode_readdir(struct nfsd4_compoundres *resp, __be32 nfserr,
+		     union nfsd4_op_u *u)
 {
+	struct nfsd4_readdir *readdir = &u->readdir;
 	int maxcount;
 	int bytes_left;
 	loff_t offset;
@@ -4160,8 +4290,10 @@
 }
 
 static __be32
-nfsd4_encode_remove(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_remove *remove)
+nfsd4_encode_remove(struct nfsd4_compoundres *resp, __be32 nfserr,
+		    union nfsd4_op_u *u)
 {
+	struct nfsd4_remove *remove = &u->remove;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4173,8 +4305,10 @@
 }
 
 static __be32
-nfsd4_encode_rename(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_rename *rename)
+nfsd4_encode_rename(struct nfsd4_compoundres *resp, __be32 nfserr,
+		    union nfsd4_op_u *u)
 {
+	struct nfsd4_rename *rename = &u->rename;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4256,8 +4390,9 @@
 
 static __be32
 nfsd4_encode_secinfo(struct nfsd4_compoundres *resp, __be32 nfserr,
-		     struct nfsd4_secinfo *secinfo)
+		     union nfsd4_op_u *u)
 {
+	struct nfsd4_secinfo *secinfo = &u->secinfo;
 	struct xdr_stream *xdr = resp->xdr;
 
 	return nfsd4_do_encode_secinfo(xdr, secinfo->si_exp);
@@ -4265,8 +4400,9 @@
 
 static __be32
 nfsd4_encode_secinfo_no_name(struct nfsd4_compoundres *resp, __be32 nfserr,
-		     struct nfsd4_secinfo_no_name *secinfo)
+		     union nfsd4_op_u *u)
 {
+	struct nfsd4_secinfo_no_name *secinfo = &u->secinfo_no_name;
 	struct xdr_stream *xdr = resp->xdr;
 
 	return nfsd4_do_encode_secinfo(xdr, secinfo->sin_exp);
@@ -4277,8 +4413,10 @@
  * regardless of the error status.
  */
 static __be32
-nfsd4_encode_setattr(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_setattr *setattr)
+nfsd4_encode_setattr(struct nfsd4_compoundres *resp, __be32 nfserr,
+		     union nfsd4_op_u *u)
 {
+	struct nfsd4_setattr *setattr = &u->setattr;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4301,8 +4439,10 @@
 }
 
 static __be32
-nfsd4_encode_setclientid(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_setclientid *scd)
+nfsd4_encode_setclientid(struct nfsd4_compoundres *resp, __be32 nfserr,
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_setclientid *scd = &u->setclientid;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4325,8 +4465,10 @@
 }
 
 static __be32
-nfsd4_encode_write(struct nfsd4_compoundres *resp, __be32 nfserr, struct nfsd4_write *write)
+nfsd4_encode_write(struct nfsd4_compoundres *resp, __be32 nfserr,
+		   union nfsd4_op_u *u)
 {
+	struct nfsd4_write *write = &u->write;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4342,8 +4484,9 @@
 
 static __be32
 nfsd4_encode_exchange_id(struct nfsd4_compoundres *resp, __be32 nfserr,
-			 struct nfsd4_exchange_id *exid)
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_exchange_id *exid = &u->exchange_id;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 	char *major_id;
@@ -4420,8 +4563,9 @@
 
 static __be32
 nfsd4_encode_create_session(struct nfsd4_compoundres *resp, __be32 nfserr,
-			    struct nfsd4_create_session *sess)
+			    union nfsd4_op_u *u)
 {
+	struct nfsd4_create_session *sess = &u->create_session;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4473,8 +4617,9 @@
 
 static __be32
 nfsd4_encode_sequence(struct nfsd4_compoundres *resp, __be32 nfserr,
-		      struct nfsd4_sequence *seq)
+		      union nfsd4_op_u *u)
 {
+	struct nfsd4_sequence *seq = &u->sequence;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4496,8 +4641,9 @@
 
 static __be32
 nfsd4_encode_test_stateid(struct nfsd4_compoundres *resp, __be32 nfserr,
-			  struct nfsd4_test_stateid *test_stateid)
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_test_stateid *test_stateid = &u->test_stateid;
 	struct xdr_stream *xdr = resp->xdr;
 	struct nfsd4_test_stateid_id *stateid, *next;
 	__be32 *p;
@@ -4517,8 +4663,9 @@
 #ifdef CONFIG_NFSD_PNFS
 static __be32
 nfsd4_encode_getdeviceinfo(struct nfsd4_compoundres *resp, __be32 nfserr,
-		struct nfsd4_getdeviceinfo *gdev)
+		union nfsd4_op_u *u)
 {
+	struct nfsd4_getdeviceinfo *gdev = &u->getdeviceinfo;
 	struct xdr_stream *xdr = resp->xdr;
 	const struct nfsd4_layout_ops *ops;
 	u32 starting_len = xdr->buf->len, needed_len;
@@ -4530,20 +4677,17 @@
 
 	*p++ = cpu_to_be32(gdev->gd_layout_type);
 
-	/* If maxcount is 0 then just update notifications */
-	if (gdev->gd_maxcount != 0) {
-		ops = nfsd4_layout_ops[gdev->gd_layout_type];
-		nfserr = ops->encode_getdeviceinfo(xdr, gdev);
-		if (nfserr) {
-			/*
-			 * We don't bother to burden the layout drivers with
-			 * enforcing gd_maxcount, just tell the client to
-			 * come back with a bigger buffer if it's not enough.
-			 */
-			if (xdr->buf->len + 4 > gdev->gd_maxcount)
-				goto toosmall;
-			return nfserr;
-		}
+	ops = nfsd4_layout_ops[gdev->gd_layout_type];
+	nfserr = ops->encode_getdeviceinfo(xdr, gdev);
+	if (nfserr) {
+		/*
+		 * We don't bother to burden the layout drivers with
+		 * enforcing gd_maxcount, just tell the client to
+		 * come back with a bigger buffer if it's not enough.
+		 */
+		if (xdr->buf->len + 4 > gdev->gd_maxcount)
+			goto toosmall;
+		return nfserr;
 	}
 
 	if (gdev->gd_notify_types) {
@@ -4573,8 +4717,9 @@
 
 static __be32
 nfsd4_encode_layoutget(struct nfsd4_compoundres *resp, __be32 nfserr,
-		struct nfsd4_layoutget *lgp)
+		union nfsd4_op_u *u)
 {
+	struct nfsd4_layoutget *lgp = &u->layoutget;
 	struct xdr_stream *xdr = resp->xdr;
 	const struct nfsd4_layout_ops *ops;
 	__be32 *p;
@@ -4600,8 +4745,9 @@
 
 static __be32
 nfsd4_encode_layoutcommit(struct nfsd4_compoundres *resp, __be32 nfserr,
-			  struct nfsd4_layoutcommit *lcp)
+			  union nfsd4_op_u *u)
 {
+	struct nfsd4_layoutcommit *lcp = &u->layoutcommit;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4621,8 +4767,9 @@
 
 static __be32
 nfsd4_encode_layoutreturn(struct nfsd4_compoundres *resp, __be32 nfserr,
-		struct nfsd4_layoutreturn *lrp)
+		union nfsd4_op_u *u)
 {
+	struct nfsd4_layoutreturn *lrp = &u->layoutreturn;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4707,25 +4854,27 @@
 
 static __be32
 nfsd4_encode_copy(struct nfsd4_compoundres *resp, __be32 nfserr,
-		  struct nfsd4_copy *copy)
+		  union nfsd4_op_u *u)
 {
+	struct nfsd4_copy *copy = &u->copy;
 	__be32 *p;
 
 	nfserr = nfsd42_encode_write_res(resp, &copy->cp_res,
-					 !!copy->cp_synchronous);
+					 nfsd4_copy_is_sync(copy));
 	if (nfserr)
 		return nfserr;
 
 	p = xdr_reserve_space(resp->xdr, 4 + 4);
 	*p++ = xdr_one; /* cr_consecutive */
-	*p++ = cpu_to_be32(copy->cp_synchronous);
+	*p = nfsd4_copy_is_sync(copy) ? xdr_one : xdr_zero;
 	return 0;
 }
 
 static __be32
 nfsd4_encode_offload_status(struct nfsd4_compoundres *resp, __be32 nfserr,
-			    struct nfsd4_offload_status *os)
+			    union nfsd4_op_u *u)
 {
+	struct nfsd4_offload_status *os = &u->offload_status;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4739,158 +4888,83 @@
 
 static __be32
 nfsd4_encode_read_plus_data(struct nfsd4_compoundres *resp,
-			    struct nfsd4_read *read,
-			    unsigned long *maxcount, u32 *eof,
-			    loff_t *pos)
+			    struct nfsd4_read *read)
 {
-	struct xdr_stream *xdr = resp->xdr;
+	bool splice_ok = test_bit(RQ_SPLICE_OK, &resp->rqstp->rq_flags);
 	struct file *file = read->rd_nf->nf_file;
-	int starting_len = xdr->buf->len;
-	loff_t hole_pos;
-	__be32 nfserr;
-	__be32 *p, tmp;
-	__be64 tmp64;
-
-	hole_pos = pos ? *pos : vfs_llseek(file, read->rd_offset, SEEK_HOLE);
-	if (hole_pos > read->rd_offset)
-		*maxcount = min_t(unsigned long, *maxcount, hole_pos - read->rd_offset);
-	*maxcount = min_t(unsigned long, *maxcount, (xdr->buf->buflen - xdr->buf->len));
+	struct xdr_stream *xdr = resp->xdr;
+	unsigned long maxcount;
+	__be32 nfserr, *p;
 
 	/* Content type, offset, byte count */
 	p = xdr_reserve_space(xdr, 4 + 8 + 4);
 	if (!p)
-		return nfserr_resource;
+		return nfserr_io;
+	if (resp->xdr->buf->page_len && splice_ok) {
+		WARN_ON_ONCE(splice_ok);
+		return nfserr_serverfault;
+	}
 
-	read->rd_vlen = xdr_reserve_space_vec(xdr, resp->rqstp->rq_vec, *maxcount);
-	if (read->rd_vlen < 0)
-		return nfserr_resource;
+	maxcount = min_t(unsigned long, read->rd_length,
+			 (xdr->buf->buflen - xdr->buf->len));
 
-	nfserr = nfsd_readv(resp->rqstp, read->rd_fhp, file, read->rd_offset,
-			    resp->rqstp->rq_vec, read->rd_vlen, maxcount, eof);
+	if (file->f_op->splice_read && splice_ok)
+		nfserr = nfsd4_encode_splice_read(resp, read, file, maxcount);
+	else
+		nfserr = nfsd4_encode_readv(resp, read, file, maxcount);
 	if (nfserr)
 		return nfserr;
-	xdr_truncate_encode(xdr, starting_len + 16 + xdr_align_size(*maxcount));
-
-	tmp = htonl(NFS4_CONTENT_DATA);
-	write_bytes_to_xdr_buf(xdr->buf, starting_len,      &tmp,   4);
-	tmp64 = cpu_to_be64(read->rd_offset);
-	write_bytes_to_xdr_buf(xdr->buf, starting_len + 4,  &tmp64, 8);
-	tmp = htonl(*maxcount);
-	write_bytes_to_xdr_buf(xdr->buf, starting_len + 12, &tmp,   4);
-
-	tmp = xdr_zero;
-	write_bytes_to_xdr_buf(xdr->buf, starting_len + 16 + *maxcount, &tmp,
-			       xdr_pad_size(*maxcount));
-	return nfs_ok;
-}
-
-static __be32
-nfsd4_encode_read_plus_hole(struct nfsd4_compoundres *resp,
-			    struct nfsd4_read *read,
-			    unsigned long *maxcount, u32 *eof)
-{
-	struct file *file = read->rd_nf->nf_file;
-	loff_t data_pos = vfs_llseek(file, read->rd_offset, SEEK_DATA);
-	loff_t f_size = i_size_read(file_inode(file));
-	unsigned long count;
-	__be32 *p;
-
-	if (data_pos == -ENXIO)
-		data_pos = f_size;
-	else if (data_pos <= read->rd_offset || (data_pos < f_size && data_pos % PAGE_SIZE))
-		return nfsd4_encode_read_plus_data(resp, read, maxcount, eof, &f_size);
-	count = data_pos - read->rd_offset;
-
-	/* Content type, offset, byte count */
-	p = xdr_reserve_space(resp->xdr, 4 + 8 + 8);
-	if (!p)
-		return nfserr_resource;
 
-	*p++ = htonl(NFS4_CONTENT_HOLE);
-	 p   = xdr_encode_hyper(p, read->rd_offset);
-	 p   = xdr_encode_hyper(p, count);
+	*p++ = cpu_to_be32(NFS4_CONTENT_DATA);
+	p = xdr_encode_hyper(p, read->rd_offset);
+	*p = cpu_to_be32(read->rd_length);
 
-	*eof = (read->rd_offset + count) >= f_size;
-	*maxcount = min_t(unsigned long, count, *maxcount);
 	return nfs_ok;
 }
 
 static __be32
 nfsd4_encode_read_plus(struct nfsd4_compoundres *resp, __be32 nfserr,
-		       struct nfsd4_read *read)
+		       union nfsd4_op_u *u)
 {
-	unsigned long maxcount, count;
+	struct nfsd4_read *read = &u->read;
+	struct file *file = read->rd_nf->nf_file;
 	struct xdr_stream *xdr = resp->xdr;
-	struct file *file;
 	int starting_len = xdr->buf->len;
-	int last_segment = xdr->buf->len;
-	int segments = 0;
-	__be32 *p, tmp;
-	bool is_data;
-	loff_t pos;
-	u32 eof;
+	u32 segments = 0;
+	__be32 *p;
 
 	if (nfserr)
 		return nfserr;
-	file = read->rd_nf->nf_file;
 
 	/* eof flag, segment count */
 	p = xdr_reserve_space(xdr, 4 + 4);
 	if (!p)
-		return nfserr_resource;
+		return nfserr_io;
 	xdr_commit_encode(xdr);
 
-	maxcount = svc_max_payload(resp->rqstp);
-	maxcount = min_t(unsigned long, maxcount,
-			 (xdr->buf->buflen - xdr->buf->len));
-	maxcount = min_t(unsigned long, maxcount, read->rd_length);
-	count    = maxcount;
-
-	eof = read->rd_offset >= i_size_read(file_inode(file));
-	if (eof)
+	read->rd_eof = read->rd_offset >= i_size_read(file_inode(file));
+	if (read->rd_eof)
 		goto out;
 
-	pos = vfs_llseek(file, read->rd_offset, SEEK_HOLE);
-	is_data = pos > read->rd_offset;
-
-	while (count > 0 && !eof) {
-		maxcount = count;
-		if (is_data)
-			nfserr = nfsd4_encode_read_plus_data(resp, read, &maxcount, &eof,
-						segments == 0 ? &pos : NULL);
-		else
-			nfserr = nfsd4_encode_read_plus_hole(resp, read, &maxcount, &eof);
-		if (nfserr)
-			goto out;
-		count -= maxcount;
-		read->rd_offset += maxcount;
-		is_data = !is_data;
-		last_segment = xdr->buf->len;
-		segments++;
-	}
-
-out:
-	if (nfserr && segments == 0)
+	nfserr = nfsd4_encode_read_plus_data(resp, read);
+	if (nfserr) {
 		xdr_truncate_encode(xdr, starting_len);
-	else {
-		if (nfserr) {
-			xdr_truncate_encode(xdr, last_segment);
-			nfserr = nfs_ok;
-			eof = 0;
-		}
-		tmp = htonl(eof);
-		write_bytes_to_xdr_buf(xdr->buf, starting_len,     &tmp, 4);
-		tmp = htonl(segments);
-		write_bytes_to_xdr_buf(xdr->buf, starting_len + 4, &tmp, 4);
+		return nfserr;
 	}
 
+	segments++;
+
+out:
+	p = xdr_encode_bool(p, read->rd_eof);
+	*p = cpu_to_be32(segments);
 	return nfserr;
 }
 
 static __be32
 nfsd4_encode_copy_notify(struct nfsd4_compoundres *resp, __be32 nfserr,
-			 struct nfsd4_copy_notify *cn)
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_copy_notify *cn = &u->copy_notify;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -4918,13 +4992,15 @@
 
 	*p++ = cpu_to_be32(1);
 
-	return nfsd42_encode_nl4_server(resp, &cn->cpn_src);
+	nfserr = nfsd42_encode_nl4_server(resp, cn->cpn_src);
+	return nfserr;
 }
 
 static __be32
 nfsd4_encode_seek(struct nfsd4_compoundres *resp, __be32 nfserr,
-		  struct nfsd4_seek *seek)
+		  union nfsd4_op_u *u)
 {
+	struct nfsd4_seek *seek = &u->seek;
 	__be32 *p;
 
 	p = xdr_reserve_space(resp->xdr, 4 + 8);
@@ -4935,7 +5011,8 @@
 }
 
 static __be32
-nfsd4_encode_noop(struct nfsd4_compoundres *resp, __be32 nfserr, void *p)
+nfsd4_encode_noop(struct nfsd4_compoundres *resp, __be32 nfserr,
+		  union nfsd4_op_u *p)
 {
 	return nfserr;
 }
@@ -4986,8 +5063,9 @@
 
 static __be32
 nfsd4_encode_getxattr(struct nfsd4_compoundres *resp, __be32 nfserr,
-		      struct nfsd4_getxattr *getxattr)
+		      union nfsd4_op_u *u)
 {
+	struct nfsd4_getxattr *getxattr = &u->getxattr;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p, err;
 
@@ -5010,8 +5088,9 @@
 
 static __be32
 nfsd4_encode_setxattr(struct nfsd4_compoundres *resp, __be32 nfserr,
-		      struct nfsd4_setxattr *setxattr)
+		      union nfsd4_op_u *u)
 {
+	struct nfsd4_setxattr *setxattr = &u->setxattr;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -5051,8 +5130,9 @@
 
 static __be32
 nfsd4_encode_listxattrs(struct nfsd4_compoundres *resp, __be32 nfserr,
-			struct nfsd4_listxattrs *listxattrs)
+			union nfsd4_op_u *u)
 {
+	struct nfsd4_listxattrs *listxattrs = &u->listxattrs;
 	struct xdr_stream *xdr = resp->xdr;
 	u32 cookie_offset, count_offset, eof;
 	u32 left, xdrleft, slen, count;
@@ -5162,8 +5242,9 @@
 
 static __be32
 nfsd4_encode_removexattr(struct nfsd4_compoundres *resp, __be32 nfserr,
-			 struct nfsd4_removexattr *removexattr)
+			 union nfsd4_op_u *u)
 {
+	struct nfsd4_removexattr *removexattr = &u->removexattr;
 	struct xdr_stream *xdr = resp->xdr;
 	__be32 *p;
 
@@ -5175,7 +5256,7 @@
 	return 0;
 }
 
-typedef __be32(* nfsd4_enc)(struct nfsd4_compoundres *, __be32, void *);
+typedef __be32(*nfsd4_enc)(struct nfsd4_compoundres *, __be32, union nfsd4_op_u *u);
 
 /*
  * Note: nfsd4_enc_ops vector is shared for v4.0 and v4.1
@@ -5183,93 +5264,93 @@
  * done in the decoding phase.
  */
 static const nfsd4_enc nfsd4_enc_ops[] = {
-	[OP_ACCESS]		= (nfsd4_enc)nfsd4_encode_access,
-	[OP_CLOSE]		= (nfsd4_enc)nfsd4_encode_close,
-	[OP_COMMIT]		= (nfsd4_enc)nfsd4_encode_commit,
-	[OP_CREATE]		= (nfsd4_enc)nfsd4_encode_create,
-	[OP_DELEGPURGE]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_DELEGRETURN]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_GETATTR]		= (nfsd4_enc)nfsd4_encode_getattr,
-	[OP_GETFH]		= (nfsd4_enc)nfsd4_encode_getfh,
-	[OP_LINK]		= (nfsd4_enc)nfsd4_encode_link,
-	[OP_LOCK]		= (nfsd4_enc)nfsd4_encode_lock,
-	[OP_LOCKT]		= (nfsd4_enc)nfsd4_encode_lockt,
-	[OP_LOCKU]		= (nfsd4_enc)nfsd4_encode_locku,
-	[OP_LOOKUP]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LOOKUPP]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_NVERIFY]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_OPEN]		= (nfsd4_enc)nfsd4_encode_open,
-	[OP_OPENATTR]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_OPEN_CONFIRM]	= (nfsd4_enc)nfsd4_encode_open_confirm,
-	[OP_OPEN_DOWNGRADE]	= (nfsd4_enc)nfsd4_encode_open_downgrade,
-	[OP_PUTFH]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_PUTPUBFH]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_PUTROOTFH]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_READ]		= (nfsd4_enc)nfsd4_encode_read,
-	[OP_READDIR]		= (nfsd4_enc)nfsd4_encode_readdir,
-	[OP_READLINK]		= (nfsd4_enc)nfsd4_encode_readlink,
-	[OP_REMOVE]		= (nfsd4_enc)nfsd4_encode_remove,
-	[OP_RENAME]		= (nfsd4_enc)nfsd4_encode_rename,
-	[OP_RENEW]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_RESTOREFH]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_SAVEFH]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_SECINFO]		= (nfsd4_enc)nfsd4_encode_secinfo,
-	[OP_SETATTR]		= (nfsd4_enc)nfsd4_encode_setattr,
-	[OP_SETCLIENTID]	= (nfsd4_enc)nfsd4_encode_setclientid,
-	[OP_SETCLIENTID_CONFIRM] = (nfsd4_enc)nfsd4_encode_noop,
-	[OP_VERIFY]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_WRITE]		= (nfsd4_enc)nfsd4_encode_write,
-	[OP_RELEASE_LOCKOWNER]	= (nfsd4_enc)nfsd4_encode_noop,
+	[OP_ACCESS]		= nfsd4_encode_access,
+	[OP_CLOSE]		= nfsd4_encode_close,
+	[OP_COMMIT]		= nfsd4_encode_commit,
+	[OP_CREATE]		= nfsd4_encode_create,
+	[OP_DELEGPURGE]		= nfsd4_encode_noop,
+	[OP_DELEGRETURN]	= nfsd4_encode_noop,
+	[OP_GETATTR]		= nfsd4_encode_getattr,
+	[OP_GETFH]		= nfsd4_encode_getfh,
+	[OP_LINK]		= nfsd4_encode_link,
+	[OP_LOCK]		= nfsd4_encode_lock,
+	[OP_LOCKT]		= nfsd4_encode_lockt,
+	[OP_LOCKU]		= nfsd4_encode_locku,
+	[OP_LOOKUP]		= nfsd4_encode_noop,
+	[OP_LOOKUPP]		= nfsd4_encode_noop,
+	[OP_NVERIFY]		= nfsd4_encode_noop,
+	[OP_OPEN]		= nfsd4_encode_open,
+	[OP_OPENATTR]		= nfsd4_encode_noop,
+	[OP_OPEN_CONFIRM]	= nfsd4_encode_open_confirm,
+	[OP_OPEN_DOWNGRADE]	= nfsd4_encode_open_downgrade,
+	[OP_PUTFH]		= nfsd4_encode_noop,
+	[OP_PUTPUBFH]		= nfsd4_encode_noop,
+	[OP_PUTROOTFH]		= nfsd4_encode_noop,
+	[OP_READ]		= nfsd4_encode_read,
+	[OP_READDIR]		= nfsd4_encode_readdir,
+	[OP_READLINK]		= nfsd4_encode_readlink,
+	[OP_REMOVE]		= nfsd4_encode_remove,
+	[OP_RENAME]		= nfsd4_encode_rename,
+	[OP_RENEW]		= nfsd4_encode_noop,
+	[OP_RESTOREFH]		= nfsd4_encode_noop,
+	[OP_SAVEFH]		= nfsd4_encode_noop,
+	[OP_SECINFO]		= nfsd4_encode_secinfo,
+	[OP_SETATTR]		= nfsd4_encode_setattr,
+	[OP_SETCLIENTID]	= nfsd4_encode_setclientid,
+	[OP_SETCLIENTID_CONFIRM] = nfsd4_encode_noop,
+	[OP_VERIFY]		= nfsd4_encode_noop,
+	[OP_WRITE]		= nfsd4_encode_write,
+	[OP_RELEASE_LOCKOWNER]	= nfsd4_encode_noop,
 
 	/* NFSv4.1 operations */
-	[OP_BACKCHANNEL_CTL]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_BIND_CONN_TO_SESSION] = (nfsd4_enc)nfsd4_encode_bind_conn_to_session,
-	[OP_EXCHANGE_ID]	= (nfsd4_enc)nfsd4_encode_exchange_id,
-	[OP_CREATE_SESSION]	= (nfsd4_enc)nfsd4_encode_create_session,
-	[OP_DESTROY_SESSION]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_FREE_STATEID]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_GET_DIR_DELEGATION]	= (nfsd4_enc)nfsd4_encode_noop,
+	[OP_BACKCHANNEL_CTL]	= nfsd4_encode_noop,
+	[OP_BIND_CONN_TO_SESSION] = nfsd4_encode_bind_conn_to_session,
+	[OP_EXCHANGE_ID]	= nfsd4_encode_exchange_id,
+	[OP_CREATE_SESSION]	= nfsd4_encode_create_session,
+	[OP_DESTROY_SESSION]	= nfsd4_encode_noop,
+	[OP_FREE_STATEID]	= nfsd4_encode_noop,
+	[OP_GET_DIR_DELEGATION]	= nfsd4_encode_noop,
 #ifdef CONFIG_NFSD_PNFS
-	[OP_GETDEVICEINFO]	= (nfsd4_enc)nfsd4_encode_getdeviceinfo,
-	[OP_GETDEVICELIST]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LAYOUTCOMMIT]	= (nfsd4_enc)nfsd4_encode_layoutcommit,
-	[OP_LAYOUTGET]		= (nfsd4_enc)nfsd4_encode_layoutget,
-	[OP_LAYOUTRETURN]	= (nfsd4_enc)nfsd4_encode_layoutreturn,
+	[OP_GETDEVICEINFO]	= nfsd4_encode_getdeviceinfo,
+	[OP_GETDEVICELIST]	= nfsd4_encode_noop,
+	[OP_LAYOUTCOMMIT]	= nfsd4_encode_layoutcommit,
+	[OP_LAYOUTGET]		= nfsd4_encode_layoutget,
+	[OP_LAYOUTRETURN]	= nfsd4_encode_layoutreturn,
 #else
-	[OP_GETDEVICEINFO]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_GETDEVICELIST]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LAYOUTCOMMIT]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LAYOUTGET]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LAYOUTRETURN]	= (nfsd4_enc)nfsd4_encode_noop,
+	[OP_GETDEVICEINFO]	= nfsd4_encode_noop,
+	[OP_GETDEVICELIST]	= nfsd4_encode_noop,
+	[OP_LAYOUTCOMMIT]	= nfsd4_encode_noop,
+	[OP_LAYOUTGET]		= nfsd4_encode_noop,
+	[OP_LAYOUTRETURN]	= nfsd4_encode_noop,
 #endif
-	[OP_SECINFO_NO_NAME]	= (nfsd4_enc)nfsd4_encode_secinfo_no_name,
-	[OP_SEQUENCE]		= (nfsd4_enc)nfsd4_encode_sequence,
-	[OP_SET_SSV]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_TEST_STATEID]	= (nfsd4_enc)nfsd4_encode_test_stateid,
-	[OP_WANT_DELEGATION]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_DESTROY_CLIENTID]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_RECLAIM_COMPLETE]	= (nfsd4_enc)nfsd4_encode_noop,
+	[OP_SECINFO_NO_NAME]	= nfsd4_encode_secinfo_no_name,
+	[OP_SEQUENCE]		= nfsd4_encode_sequence,
+	[OP_SET_SSV]		= nfsd4_encode_noop,
+	[OP_TEST_STATEID]	= nfsd4_encode_test_stateid,
+	[OP_WANT_DELEGATION]	= nfsd4_encode_noop,
+	[OP_DESTROY_CLIENTID]	= nfsd4_encode_noop,
+	[OP_RECLAIM_COMPLETE]	= nfsd4_encode_noop,
 
 	/* NFSv4.2 operations */
-	[OP_ALLOCATE]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_COPY]		= (nfsd4_enc)nfsd4_encode_copy,
-	[OP_COPY_NOTIFY]	= (nfsd4_enc)nfsd4_encode_copy_notify,
-	[OP_DEALLOCATE]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_IO_ADVISE]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LAYOUTERROR]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_LAYOUTSTATS]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_OFFLOAD_CANCEL]	= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_OFFLOAD_STATUS]	= (nfsd4_enc)nfsd4_encode_offload_status,
-	[OP_READ_PLUS]		= (nfsd4_enc)nfsd4_encode_read_plus,
-	[OP_SEEK]		= (nfsd4_enc)nfsd4_encode_seek,
-	[OP_WRITE_SAME]		= (nfsd4_enc)nfsd4_encode_noop,
-	[OP_CLONE]		= (nfsd4_enc)nfsd4_encode_noop,
+	[OP_ALLOCATE]		= nfsd4_encode_noop,
+	[OP_COPY]		= nfsd4_encode_copy,
+	[OP_COPY_NOTIFY]	= nfsd4_encode_copy_notify,
+	[OP_DEALLOCATE]		= nfsd4_encode_noop,
+	[OP_IO_ADVISE]		= nfsd4_encode_noop,
+	[OP_LAYOUTERROR]	= nfsd4_encode_noop,
+	[OP_LAYOUTSTATS]	= nfsd4_encode_noop,
+	[OP_OFFLOAD_CANCEL]	= nfsd4_encode_noop,
+	[OP_OFFLOAD_STATUS]	= nfsd4_encode_offload_status,
+	[OP_READ_PLUS]		= nfsd4_encode_read_plus,
+	[OP_SEEK]		= nfsd4_encode_seek,
+	[OP_WRITE_SAME]		= nfsd4_encode_noop,
+	[OP_CLONE]		= nfsd4_encode_noop,
 
 	/* RFC 8276 extended atributes operations */
-	[OP_GETXATTR]		= (nfsd4_enc)nfsd4_encode_getxattr,
-	[OP_SETXATTR]		= (nfsd4_enc)nfsd4_encode_setxattr,
-	[OP_LISTXATTRS]		= (nfsd4_enc)nfsd4_encode_listxattrs,
-	[OP_REMOVEXATTR]	= (nfsd4_enc)nfsd4_encode_removexattr,
+	[OP_GETXATTR]		= nfsd4_encode_getxattr,
+	[OP_SETXATTR]		= nfsd4_encode_setxattr,
+	[OP_LISTXATTRS]		= nfsd4_encode_listxattrs,
+	[OP_REMOVEXATTR]	= nfsd4_encode_removexattr,
 };
 
 /*
@@ -5313,10 +5394,8 @@
 	__be32 *p;
 
 	p = xdr_reserve_space(xdr, 8);
-	if (!p) {
-		WARN_ON_ONCE(1);
-		return;
-	}
+	if (!p)
+		goto release;
 	*p++ = cpu_to_be32(op->opnum);
 	post_err_offset = xdr->buf->len;
 
@@ -5331,8 +5410,6 @@
 	op->status = encoder(resp, op->status, &op->u);
 	if (op->status)
 		trace_nfsd_compound_encode_err(rqstp, op->opnum, op->status);
-	if (opdesc && opdesc->op_release)
-		opdesc->op_release(&op->u);
 	xdr_commit_encode(xdr);
 
 	/* nfsd4_check_resp_size guarantees enough room for error status */
@@ -5372,8 +5449,10 @@
 						so->so_replay.rp_buf, len);
 	}
 status:
-	/* Note that op->status is already in network byte order: */
-	write_bytes_to_xdr_buf(xdr->buf, post_err_offset - 4, &op->status, 4);
+	*p = op->status;
+release:
+	if (opdesc && opdesc->op_release)
+		opdesc->op_release(&op->u);
 }
 
 /* 
@@ -5404,7 +5483,7 @@
 	struct nfsd4_compoundargs *args = rqstp->rq_argp;
 
 	if (args->ops != args->iops) {
-		kfree(args->ops);
+		vfree(args->ops);
 		args->ops = args->iops;
 	}
 	while (args->to_free) {
@@ -5414,40 +5493,42 @@
 	}
 }
 
-int
-nfs4svc_decode_compoundargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs4svc_decode_compoundargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
 	struct nfsd4_compoundargs *args = rqstp->rq_argp;
 
 	/* svcxdr_tmp_alloc */
 	args->to_free = NULL;
 
-	args->xdr = &rqstp->rq_arg_stream;
+	args->xdr = xdr;
 	args->ops = args->iops;
 	args->rqstp = rqstp;
 
 	return nfsd4_decode_compound(args);
 }
 
-int
-nfs4svc_encode_compoundres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfs4svc_encode_compoundres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
 	struct nfsd4_compoundres *resp = rqstp->rq_resp;
-	struct xdr_buf *buf = resp->xdr->buf;
+	__be32 *p;
 
-	WARN_ON_ONCE(buf->len != buf->head[0].iov_len + buf->page_len +
-				 buf->tail[0].iov_len);
+	/*
+	 * Send buffer space for the following items is reserved
+	 * at the top of nfsd4_proc_compound().
+	 */
+	p = resp->statusp;
 
-	*p = resp->cstate.status;
+	*p++ = resp->cstate.status;
 
-	rqstp->rq_next_page = resp->xdr->page_ptr + 1;
+	rqstp->rq_next_page = xdr->page_ptr + 1;
 
-	p = resp->tagp;
 	*p++ = htonl(resp->taglen);
 	memcpy(p, resp->tag, resp->taglen);
 	p += XDR_QUADLEN(resp->taglen);
 	*p++ = htonl(resp->opcnt);
 
 	nfsd4_sequence_done(resp);
-	return 1;
+	return true;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfscache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfscache.c
@@ -84,15 +84,9 @@
 	return roundup_pow_of_two(limit / TARGET_BUCKET_SIZE);
 }
 
-static u32
-nfsd_cache_hash(__be32 xid, struct nfsd_net *nn)
-{
-	return hash_32(be32_to_cpu(xid), nn->maskbits);
-}
-
 static struct svc_cacherep *
-nfsd_reply_cache_alloc(struct svc_rqst *rqstp, __wsum csum,
-			struct nfsd_net *nn)
+nfsd_cacherep_alloc(struct svc_rqst *rqstp, __wsum csum,
+		    struct nfsd_net *nn)
 {
 	struct svc_cacherep	*rp;
 
@@ -116,21 +110,48 @@
 	return rp;
 }
 
-static void
-nfsd_reply_cache_free_locked(struct nfsd_drc_bucket *b, struct svc_cacherep *rp,
-				struct nfsd_net *nn)
+static void nfsd_cacherep_free(struct svc_cacherep *rp)
 {
-	if (rp->c_type == RC_REPLBUFF && rp->c_replvec.iov_base) {
-		nfsd_stats_drc_mem_usage_sub(nn, rp->c_replvec.iov_len);
+	if (rp->c_type == RC_REPLBUFF)
 		kfree(rp->c_replvec.iov_base);
+	kmem_cache_free(drc_slab, rp);
+}
+
+static unsigned long
+nfsd_cacherep_dispose(struct list_head *dispose)
+{
+	struct svc_cacherep *rp;
+	unsigned long freed = 0;
+
+	while (!list_empty(dispose)) {
+		rp = list_first_entry(dispose, struct svc_cacherep, c_lru);
+		list_del(&rp->c_lru);
+		nfsd_cacherep_free(rp);
+		freed++;
 	}
+	return freed;
+}
+
+static void
+nfsd_cacherep_unlink_locked(struct nfsd_net *nn, struct nfsd_drc_bucket *b,
+			    struct svc_cacherep *rp)
+{
+	if (rp->c_type == RC_REPLBUFF && rp->c_replvec.iov_base)
+		nfsd_stats_drc_mem_usage_sub(nn, rp->c_replvec.iov_len);
 	if (rp->c_state != RC_UNUSED) {
 		rb_erase(&rp->c_node, &b->rb_head);
 		list_del(&rp->c_lru);
 		atomic_dec(&nn->num_drc_entries);
 		nfsd_stats_drc_mem_usage_sub(nn, sizeof(*rp));
 	}
-	kmem_cache_free(drc_slab, rp);
+}
+
+static void
+nfsd_reply_cache_free_locked(struct nfsd_drc_bucket *b, struct svc_cacherep *rp,
+				struct nfsd_net *nn)
+{
+	nfsd_cacherep_unlink_locked(nn, b, rp);
+	nfsd_cacherep_free(rp);
 }
 
 static void
@@ -138,8 +159,9 @@
 			struct nfsd_net *nn)
 {
 	spin_lock(&b->cache_lock);
-	nfsd_reply_cache_free_locked(b, rp, nn);
+	nfsd_cacherep_unlink_locked(nn, b, rp);
 	spin_unlock(&b->cache_lock);
+	nfsd_cacherep_free(rp);
 }
 
 int nfsd_drc_slab_create(void)
@@ -154,16 +176,6 @@
 	kmem_cache_destroy(drc_slab);
 }
 
-static int nfsd_reply_cache_stats_init(struct nfsd_net *nn)
-{
-	return nfsd_percpu_counters_init(nn->counter, NFSD_NET_COUNTERS_NUM);
-}
-
-static void nfsd_reply_cache_stats_destroy(struct nfsd_net *nn)
-{
-	nfsd_percpu_counters_destroy(nn->counter, NFSD_NET_COUNTERS_NUM);
-}
-
 int nfsd_reply_cache_init(struct nfsd_net *nn)
 {
 	unsigned int hashsize;
@@ -175,16 +187,12 @@
 	hashsize = nfsd_hashsize(nn->max_drc_entries);
 	nn->maskbits = ilog2(hashsize);
 
-	status = nfsd_reply_cache_stats_init(nn);
-	if (status)
-		goto out_nomem;
-
 	nn->nfsd_reply_cache_shrinker.scan_objects = nfsd_reply_cache_scan;
 	nn->nfsd_reply_cache_shrinker.count_objects = nfsd_reply_cache_count;
 	nn->nfsd_reply_cache_shrinker.seeks = 1;
 	status = register_shrinker(&nn->nfsd_reply_cache_shrinker);
 	if (status)
-		goto out_stats_destroy;
+		return status;
 
 	nn->drc_hashtbl = kvzalloc(array_size(hashsize,
 				sizeof(*nn->drc_hashtbl)), GFP_KERNEL);
@@ -200,9 +208,6 @@
 	return 0;
 out_shrinker:
 	unregister_shrinker(&nn->nfsd_reply_cache_shrinker);
-out_stats_destroy:
-	nfsd_reply_cache_stats_destroy(nn);
-out_nomem:
 	printk(KERN_ERR "nfsd: failed to allocate reply cache\n");
 	return -ENOMEM;
 }
@@ -212,7 +217,6 @@
 	struct svc_cacherep	*rp;
 	unsigned int i;
 
-	nfsd_reply_cache_stats_destroy(nn);
 	unregister_shrinker(&nn->nfsd_reply_cache_shrinker);
 
 	for (i = 0; i < nn->drc_hashsize; i++) {
@@ -241,12 +245,29 @@
 	list_move_tail(&rp->c_lru, &b->lru_head);
 }
 
-static long
-prune_bucket(struct nfsd_drc_bucket *b, struct nfsd_net *nn)
+static noinline struct nfsd_drc_bucket *
+nfsd_cache_bucket_find(__be32 xid, struct nfsd_net *nn)
+{
+	unsigned int hash = hash_32((__force u32)xid, nn->maskbits);
+
+	return &nn->drc_hashtbl[hash];
+}
+
+/*
+ * Remove and return no more than @max expired entries in bucket @b.
+ * If @max is zero, do not limit the number of removed entries.
+ */
+static void
+nfsd_prune_bucket_locked(struct nfsd_net *nn, struct nfsd_drc_bucket *b,
+			 unsigned int max, struct list_head *dispose)
 {
+	unsigned long expiry = jiffies - RC_EXPIRE;
 	struct svc_cacherep *rp, *tmp;
-	long freed = 0;
+	unsigned int freed = 0;
+
+	lockdep_assert_held(&b->cache_lock);
 
+	/* The bucket LRU is ordered oldest-first. */
 	list_for_each_entry_safe(rp, tmp, &b->lru_head, c_lru) {
 		/*
 		 * Don't free entries attached to calls that are still
@@ -254,37 +275,29 @@
 		 */
 		if (rp->c_state == RC_INPROG)
 			continue;
+
 		if (atomic_read(&nn->num_drc_entries) <= nn->max_drc_entries &&
-		    time_before(jiffies, rp->c_timestamp + RC_EXPIRE))
+		    time_before(expiry, rp->c_timestamp))
 			break;
-		nfsd_reply_cache_free_locked(b, rp, nn);
-		freed++;
-	}
-	return freed;
-}
-
-/*
- * Walk the LRU list and prune off entries that are older than RC_EXPIRE.
- * Also prune the oldest ones when the total exceeds the max number of entries.
- */
-static long
-prune_cache_entries(struct nfsd_net *nn)
-{
-	unsigned int i;
-	long freed = 0;
 
-	for (i = 0; i < nn->drc_hashsize; i++) {
-		struct nfsd_drc_bucket *b = &nn->drc_hashtbl[i];
+		nfsd_cacherep_unlink_locked(nn, b, rp);
+		list_add(&rp->c_lru, dispose);
 
-		if (list_empty(&b->lru_head))
-			continue;
-		spin_lock(&b->cache_lock);
-		freed += prune_bucket(b, nn);
-		spin_unlock(&b->cache_lock);
+		if (max && ++freed > max)
+			break;
 	}
-	return freed;
 }
 
+/**
+ * nfsd_reply_cache_count - count_objects method for the DRC shrinker
+ * @shrink: our registered shrinker context
+ * @sc: garbage collection parameters
+ *
+ * Returns the total number of entries in the duplicate reply cache. To
+ * keep things simple and quick, this is not the number of expired entries
+ * in the cache (ie, the number that would be removed by a call to
+ * nfsd_reply_cache_scan).
+ */
 static unsigned long
 nfsd_reply_cache_count(struct shrinker *shrink, struct shrink_control *sc)
 {
@@ -294,14 +307,45 @@
 	return atomic_read(&nn->num_drc_entries);
 }
 
+/**
+ * nfsd_reply_cache_scan - scan_objects method for the DRC shrinker
+ * @shrink: our registered shrinker context
+ * @sc: garbage collection parameters
+ *
+ * Free expired entries on each bucket's LRU list until we've released
+ * nr_to_scan freed objects. Nothing will be released if the cache
+ * has not exceeded it's max_drc_entries limit.
+ *
+ * Returns the number of entries released by this call.
+ */
 static unsigned long
 nfsd_reply_cache_scan(struct shrinker *shrink, struct shrink_control *sc)
 {
 	struct nfsd_net *nn = container_of(shrink,
 				struct nfsd_net, nfsd_reply_cache_shrinker);
+	unsigned long freed = 0;
+	LIST_HEAD(dispose);
+	unsigned int i;
+
+	for (i = 0; i < nn->drc_hashsize; i++) {
+		struct nfsd_drc_bucket *b = &nn->drc_hashtbl[i];
+
+		if (list_empty(&b->lru_head))
+			continue;
+
+		spin_lock(&b->cache_lock);
+		nfsd_prune_bucket_locked(nn, b, 0, &dispose);
+		spin_unlock(&b->cache_lock);
 
-	return prune_cache_entries(nn);
+		freed += nfsd_cacherep_dispose(&dispose);
+		if (freed > sc->nr_to_scan)
+			break;
+	}
+
+	trace_nfsd_drc_gc(nn, freed);
+	return freed;
 }
+
 /*
  * Walk an xdr_buf and get a CRC for at most the first RC_CSUMLEN bytes
  */
@@ -413,18 +457,18 @@
  */
 int nfsd_cache_lookup(struct svc_rqst *rqstp)
 {
-	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
+	struct nfsd_net		*nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 	struct svc_cacherep	*rp, *found;
-	__be32			xid = rqstp->rq_xid;
 	__wsum			csum;
-	u32 hash = nfsd_cache_hash(xid, nn);
-	struct nfsd_drc_bucket *b = &nn->drc_hashtbl[hash];
+	struct nfsd_drc_bucket	*b;
 	int type = rqstp->rq_cachetype;
+	unsigned long freed;
+	LIST_HEAD(dispose);
 	int rtn = RC_DOIT;
 
 	rqstp->rq_cacherep = NULL;
 	if (type == RC_NOCACHE) {
-		nfsd_stats_rc_nocache_inc();
+		nfsd_stats_rc_nocache_inc(nn);
 		goto out;
 	}
 
@@ -434,37 +478,34 @@
 	 * Since the common case is a cache miss followed by an insert,
 	 * preallocate an entry.
 	 */
-	rp = nfsd_reply_cache_alloc(rqstp, csum, nn);
+	rp = nfsd_cacherep_alloc(rqstp, csum, nn);
 	if (!rp)
 		goto out;
 
+	b = nfsd_cache_bucket_find(rqstp->rq_xid, nn);
 	spin_lock(&b->cache_lock);
 	found = nfsd_cache_insert(b, rp, nn);
-	if (found != rp) {
-		nfsd_reply_cache_free_locked(NULL, rp, nn);
-		rp = found;
+	if (found != rp)
 		goto found_entry;
-	}
-
-	nfsd_stats_rc_misses_inc();
 	rqstp->rq_cacherep = rp;
 	rp->c_state = RC_INPROG;
+	nfsd_prune_bucket_locked(nn, b, 3, &dispose);
+	spin_unlock(&b->cache_lock);
+
+	freed = nfsd_cacherep_dispose(&dispose);
+	trace_nfsd_drc_gc(nn, freed);
 
+	nfsd_stats_rc_misses_inc(nn);
 	atomic_inc(&nn->num_drc_entries);
 	nfsd_stats_drc_mem_usage_add(nn, sizeof(*rp));
-
-	/* go ahead and prune the cache */
-	prune_bucket(b, nn);
-
-out_unlock:
-	spin_unlock(&b->cache_lock);
-out:
-	return rtn;
+	goto out;
 
 found_entry:
 	/* We found a matching entry which is either in progress or done. */
-	nfsd_stats_rc_hits_inc();
+	nfsd_reply_cache_free_locked(NULL, rp, nn);
+	nfsd_stats_rc_hits_inc(nn);
 	rtn = RC_DROPIT;
+	rp = found;
 
 	/* Request being processed */
 	if (rp->c_state == RC_INPROG)
@@ -495,7 +536,10 @@
 
 out_trace:
 	trace_nfsd_drc_found(nn, rqstp, rtn);
-	goto out_unlock;
+out_unlock:
+	spin_unlock(&b->cache_lock);
+out:
+	return rtn;
 }
 
 /**
@@ -523,7 +567,6 @@
 	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 	struct svc_cacherep *rp = rqstp->rq_cacherep;
 	struct kvec	*resv = &rqstp->rq_res.head[0], *cachv;
-	u32		hash;
 	struct nfsd_drc_bucket *b;
 	int		len;
 	size_t		bufsize = 0;
@@ -531,8 +574,7 @@
 	if (!rp)
 		return;
 
-	hash = nfsd_cache_hash(rp->c_key.k_xid, nn);
-	b = &nn->drc_hashtbl[hash];
+	b = nfsd_cache_bucket_find(rp->c_key.k_xid, nn);
 
 	len = resv->iov_len - ((char*)statp - (char*)resv->iov_base);
 	len >>= 2;
@@ -599,33 +641,26 @@
  * scraping this file for info should test the labels to ensure they're
  * getting the correct field.
  */
-static int nfsd_reply_cache_stats_show(struct seq_file *m, void *v)
+int nfsd_reply_cache_stats_show(struct seq_file *m, void *v)
 {
-	struct nfsd_net *nn = m->private;
+	struct nfsd_net *nn = net_generic(file_inode(m->file)->i_sb->s_fs_info,
+					  nfsd_net_id);
 
 	seq_printf(m, "max entries:           %u\n", nn->max_drc_entries);
 	seq_printf(m, "num entries:           %u\n",
 		   atomic_read(&nn->num_drc_entries));
 	seq_printf(m, "hash buckets:          %u\n", 1 << nn->maskbits);
 	seq_printf(m, "mem usage:             %lld\n",
-		   percpu_counter_sum_positive(&nn->counter[NFSD_NET_DRC_MEM_USAGE]));
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_DRC_MEM_USAGE]));
 	seq_printf(m, "cache hits:            %lld\n",
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_RC_HITS]));
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_RC_HITS]));
 	seq_printf(m, "cache misses:          %lld\n",
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_RC_MISSES]));
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_RC_MISSES]));
 	seq_printf(m, "not cached:            %lld\n",
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_RC_NOCACHE]));
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_RC_NOCACHE]));
 	seq_printf(m, "payload misses:        %lld\n",
-		   percpu_counter_sum_positive(&nn->counter[NFSD_NET_PAYLOAD_MISSES]));
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_PAYLOAD_MISSES]));
 	seq_printf(m, "longest chain len:     %u\n", nn->longest_chain);
 	seq_printf(m, "cachesize at longest:  %u\n", nn->longest_chain_cachesize);
 	return 0;
 }
-
-int nfsd_reply_cache_stats_open(struct inode *inode, struct file *file)
-{
-	struct nfsd_net *nn = net_generic(file_inode(file)->i_sb->s_fs_info,
-								nfsd_net_id);
-
-	return single_open(file, nfsd_reply_cache_stats_show, nn);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfsctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfsctl.c
@@ -25,6 +25,7 @@
 #include "state.h"
 #include "netns.h"
 #include "pnfs.h"
+#include "filecache.h"
 
 /*
  *	We have a single directory with several nodes in it.
@@ -45,6 +46,7 @@
 	NFSD_Ports,
 	NFSD_MaxBlkSize,
 	NFSD_MaxConnections,
+	NFSD_Filecache,
 	NFSD_SupportedEnctypes,
 	/*
 	 * The below MUST come last.  Otherwise we leave a hole in nfsd_files[]
@@ -183,17 +185,7 @@
 	return 0;
 }
 
-static int export_features_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, export_features_show, NULL);
-}
-
-static const struct file_operations export_features_operations = {
-	.open		= export_features_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(export_features);
 
 #if defined(CONFIG_SUNRPC_GSS) || defined(CONFIG_SUNRPC_GSS_MODULE)
 static int supported_enctypes_show(struct seq_file *m, void *v)
@@ -202,17 +194,7 @@
 	return 0;
 }
 
-static int supported_enctypes_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, supported_enctypes_show, NULL);
-}
-
-static const struct file_operations supported_enctypes_ops = {
-	.open		= supported_enctypes_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(supported_enctypes);
 #endif /* CONFIG_SUNRPC_GSS or CONFIG_SUNRPC_GSS_MODULE */
 
 static const struct file_operations pool_stats_operations = {
@@ -222,12 +204,9 @@
 	.release	= nfsd_pool_stats_release,
 };
 
-static const struct file_operations reply_cache_stats_operations = {
-	.open		= nfsd_reply_cache_stats_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(nfsd_reply_cache_stats);
+
+DEFINE_SHOW_ATTRIBUTE(nfsd_file_cache_stats);
 
 /*----------------------------------------------------------------------------*/
 /*
@@ -395,12 +374,12 @@
 	auth_domain_put(dom);
 	if (len)
 		return len;
-	
+
 	mesg = buf;
 	len = SIMPLE_TRANSACTION_LIMIT;
-	qword_addhex(&mesg, &len, (char*)&fh.fh_base, fh.fh_size);
+	qword_addhex(&mesg, &len, fh.fh_raw, fh.fh_size);
 	mesg[-1] = '\n';
-	return mesg - buf;	
+	return mesg - buf;
 }
 
 /*
@@ -602,7 +581,9 @@
 
 			cmd = sign == '-' ? NFSD_CLEAR : NFSD_SET;
 			switch(num) {
+#ifdef CONFIG_NFSD_V2
 			case 2:
+#endif
 			case 3:
 				nfsd_vers(nn, num, cmd);
 				break;
@@ -622,7 +603,9 @@
 				}
 				break;
 			default:
-				return -EINVAL;
+				/* Ignore requests to disable non-existent versions */
+				if (cmd == NFSD_SET)
+					return -EINVAL;
 			}
 			vers += len + 1;
 		} while ((len = qword_get(&mesg, vers, size)) > 0);
@@ -633,7 +616,6 @@
 	}
 
 	/* Now write current state into reply buffer */
-	len = 0;
 	sep = "";
 	remaining = SIMPLE_TRANSACTION_LIMIT;
 	for (num=2 ; num <= 4 ; num++) {
@@ -727,28 +709,25 @@
 	char *mesg = buf;
 	int fd, err;
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
+	struct svc_serv *serv;
 
 	err = get_int(&mesg, &fd);
 	if (err != 0 || fd < 0)
 		return -EINVAL;
 
-	if (svc_alien_sock(net, fd)) {
-		printk(KERN_ERR "%s: socket net is different to NFSd's one\n", __func__);
-		return -EINVAL;
-	}
-
 	err = nfsd_create_serv(net);
 	if (err != 0)
 		return err;
 
-	err = svc_addsock(nn->nfsd_serv, fd, buf, SIMPLE_TRANSACTION_LIMIT, cred);
-	if (err < 0) {
-		nfsd_destroy(net);
-		return err;
-	}
+	serv = nn->nfsd_serv;
+	err = svc_addsock(serv, net, fd, buf, SIMPLE_TRANSACTION_LIMIT, cred);
+
+	if (err < 0 && !serv->sv_nrthreads && !nn->keep_active)
+		nfsd_last_thread(net);
+	else if (err >= 0 && !serv->sv_nrthreads && !xchg(&nn->keep_active, 1))
+		svc_get(serv);
 
-	/* Decrease the count, but don't shut down the service */
-	nn->nfsd_serv->sv_nrthreads--;
+	svc_put(serv);
 	return err;
 }
 
@@ -762,6 +741,7 @@
 	struct svc_xprt *xprt;
 	int port, err;
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
+	struct svc_serv *serv;
 
 	if (sscanf(buf, "%15s %5u", transport, &port) != 2)
 		return -EINVAL;
@@ -773,30 +753,33 @@
 	if (err != 0)
 		return err;
 
-	err = svc_create_xprt(nn->nfsd_serv, transport, net,
-				PF_INET, port, SVC_SOCK_ANONYMOUS, cred);
+	serv = nn->nfsd_serv;
+	err = svc_xprt_create(serv, transport, net,
+			      PF_INET, port, SVC_SOCK_ANONYMOUS, cred);
 	if (err < 0)
 		goto out_err;
 
-	err = svc_create_xprt(nn->nfsd_serv, transport, net,
-				PF_INET6, port, SVC_SOCK_ANONYMOUS, cred);
+	err = svc_xprt_create(serv, transport, net,
+			      PF_INET6, port, SVC_SOCK_ANONYMOUS, cred);
 	if (err < 0 && err != -EAFNOSUPPORT)
 		goto out_close;
 
-	/* Decrease the count, but don't shut down the service */
-	nn->nfsd_serv->sv_nrthreads--;
+	if (!serv->sv_nrthreads && !xchg(&nn->keep_active, 1))
+		svc_get(serv);
+
+	svc_put(serv);
 	return 0;
 out_close:
-	xprt = svc_find_xprt(nn->nfsd_serv, transport, net, PF_INET, port);
+	xprt = svc_find_xprt(serv, transport, net, PF_INET, port);
 	if (xprt != NULL) {
-		svc_close_xprt(xprt);
+		svc_xprt_close(xprt);
 		svc_xprt_put(xprt);
 	}
 out_err:
-	if (!list_empty(&nn->nfsd_serv->sv_permsocks))
-		nn->nfsd_serv->sv_nrthreads--;
-	 else
-		nfsd_destroy(net);
+	if (!serv->sv_nrthreads && !nn->keep_active)
+		nfsd_last_thread(net);
+
+	svc_put(serv);
 	return err;
 }
 
@@ -1249,7 +1232,8 @@
 	clear_ncl(d_inode(dentry));
 	dget(dentry);
 	ret = simple_unlink(dir, dentry);
-	d_delete(dentry);
+	d_drop(dentry);
+	fsnotify_unlink(dir, dentry);
 	dput(dentry);
 	WARN_ON_ONCE(ret);
 }
@@ -1340,8 +1324,8 @@
 	dget(dentry);
 	ret = simple_rmdir(dir, dentry);
 	WARN_ON_ONCE(ret);
+	d_drop(dentry);
 	fsnotify_rmdir(dir, dentry);
-	d_delete(dentry);
 	dput(dentry);
 	inode_unlock(dir);
 }
@@ -1358,7 +1342,7 @@
 		/* Per-export io stats use same ops as exports file */
 		[NFSD_Export_Stats] = {"export_stats", &exports_nfsd_operations, S_IRUGO},
 		[NFSD_Export_features] = {"export_features",
-					&export_features_operations, S_IRUGO},
+					&export_features_fops, S_IRUGO},
 		[NFSD_FO_UnlockIP] = {"unlock_ip",
 					&transaction_ops, S_IWUSR|S_IRUSR},
 		[NFSD_FO_UnlockFS] = {"unlock_filesystem",
@@ -1367,13 +1351,16 @@
 		[NFSD_Threads] = {"threads", &transaction_ops, S_IWUSR|S_IRUSR},
 		[NFSD_Pool_Threads] = {"pool_threads", &transaction_ops, S_IWUSR|S_IRUSR},
 		[NFSD_Pool_Stats] = {"pool_stats", &pool_stats_operations, S_IRUGO},
-		[NFSD_Reply_Cache_Stats] = {"reply_cache_stats", &reply_cache_stats_operations, S_IRUGO},
+		[NFSD_Reply_Cache_Stats] = {"reply_cache_stats",
+					&nfsd_reply_cache_stats_fops, S_IRUGO},
 		[NFSD_Versions] = {"versions", &transaction_ops, S_IWUSR|S_IRUSR},
 		[NFSD_Ports] = {"portlist", &transaction_ops, S_IWUSR|S_IRUGO},
 		[NFSD_MaxBlkSize] = {"max_block_size", &transaction_ops, S_IWUSR|S_IRUGO},
 		[NFSD_MaxConnections] = {"max_connections", &transaction_ops, S_IWUSR|S_IRUGO},
+		[NFSD_Filecache] = {"filecache", &nfsd_file_cache_stats_fops, S_IRUGO},
 #if defined(CONFIG_SUNRPC_GSS) || defined(CONFIG_SUNRPC_GSS_MODULE)
-		[NFSD_SupportedEnctypes] = {"supported_krb5_enctypes", &supported_enctypes_ops, S_IRUGO},
+		[NFSD_SupportedEnctypes] = {"supported_krb5_enctypes",
+					&supported_enctypes_fops, S_IRUGO},
 #endif /* CONFIG_SUNRPC_GSS or CONFIG_SUNRPC_GSS_MODULE */
 #ifdef CONFIG_NFSD_V4
 		[NFSD_Leasetime] = {"nfsv4leasetime", &transaction_ops, S_IWUSR|S_IRUSR},
@@ -1471,27 +1458,21 @@
 	retval = nfsd_idmap_init(net);
 	if (retval)
 		goto out_idmap_error;
+	retval = nfsd_stat_counters_init(nn);
+	if (retval)
+		goto out_repcache_error;
+	memset(&nn->nfsd_svcstats, 0, sizeof(nn->nfsd_svcstats));
+	nn->nfsd_svcstats.program = &nfsd_program;
 	nn->nfsd_versions = NULL;
 	nn->nfsd4_minorversions = NULL;
-	retval = nfsd_reply_cache_init(nn);
-	if (retval)
-		goto out_drc_error;
-	nn->nfsd4_lease = 90;	/* default lease time */
-	nn->nfsd4_grace = 90;
-	nn->somebody_reclaimed = false;
-	nn->track_reclaim_completes = false;
-	nn->clverifier_counter = prandom_u32();
-	nn->clientid_base = prandom_u32();
-	nn->clientid_counter = nn->clientid_base + 1;
-	nn->s2s_cp_cl_id = nn->clientid_counter++;
-
-	atomic_set(&nn->ntf_refcnt, 0);
-	init_waitqueue_head(&nn->ntf_wq);
-	seqlock_init(&nn->boot_lock);
+	nfsd4_init_leases_net(nn);
+	get_random_bytes(&nn->siphash_key, sizeof(nn->siphash_key));
+	seqlock_init(&nn->writeverf_lock);
+	nfsd_proc_stat_init(net);
 
 	return 0;
 
-out_drc_error:
+out_repcache_error:
 	nfsd_idmap_shutdown(net);
 out_idmap_error:
 	nfsd_export_shutdown(net);
@@ -1503,10 +1484,11 @@
 {
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 
-	nfsd_reply_cache_shutdown(nn);
+	nfsd_proc_stat_shutdown(net);
+	nfsd_stat_counters_destroy(nn);
 	nfsd_idmap_shutdown(net);
 	nfsd_export_shutdown(net);
-	nfsd_netns_free_versions(net_generic(net, nfsd_net_id));
+	nfsd_netns_free_versions(nn);
 }
 
 static struct pernet_operations nfsd_net_ops = {
@@ -1519,65 +1501,64 @@
 static int __init init_nfsd(void)
 {
 	int retval;
-	printk(KERN_INFO "Installing knfsd (copyright (C) 1996 okir@monad.swb.de).\n");
 
-	retval = register_cld_notifier();
-	if (retval)
-		return retval;
 	retval = nfsd4_init_slabs();
 	if (retval)
-		goto out_unregister_notifier;
+		return retval;
 	retval = nfsd4_init_pnfs();
 	if (retval)
 		goto out_free_slabs;
-	retval = nfsd_stat_init();	/* Statistics */
-	if (retval)
-		goto out_free_pnfs;
 	retval = nfsd_drc_slab_create();
 	if (retval)
-		goto out_free_stat;
+		goto out_free_pnfs;
 	nfsd_lockd_init();	/* lockd->nfsd callbacks */
 	retval = create_proc_exports_entry();
 	if (retval)
 		goto out_free_lockd;
-	retval = register_filesystem(&nfsd_fs_type);
-	if (retval)
-		goto out_free_exports;
 	retval = register_pernet_subsys(&nfsd_net_ops);
 	if (retval < 0)
+		goto out_free_exports;
+	retval = register_cld_notifier();
+	if (retval)
+		goto out_free_subsys;
+	retval = nfsd4_create_laundry_wq();
+	if (retval)
+		goto out_free_cld;
+	retval = register_filesystem(&nfsd_fs_type);
+	if (retval)
 		goto out_free_all;
 	return 0;
 out_free_all:
-	unregister_filesystem(&nfsd_fs_type);
+	nfsd4_destroy_laundry_wq();
+out_free_cld:
+	unregister_cld_notifier();
+out_free_subsys:
+	unregister_pernet_subsys(&nfsd_net_ops);
 out_free_exports:
 	remove_proc_entry("fs/nfs/exports", NULL);
 	remove_proc_entry("fs/nfs", NULL);
 out_free_lockd:
 	nfsd_lockd_shutdown();
 	nfsd_drc_slab_free();
-out_free_stat:
-	nfsd_stat_shutdown();
 out_free_pnfs:
 	nfsd4_exit_pnfs();
 out_free_slabs:
 	nfsd4_free_slabs();
-out_unregister_notifier:
-	unregister_cld_notifier();
 	return retval;
 }
 
 static void __exit exit_nfsd(void)
 {
+	unregister_filesystem(&nfsd_fs_type);
+	nfsd4_destroy_laundry_wq();
+	unregister_cld_notifier();
 	unregister_pernet_subsys(&nfsd_net_ops);
 	nfsd_drc_slab_free();
 	remove_proc_entry("fs/nfs/exports", NULL);
 	remove_proc_entry("fs/nfs", NULL);
-	nfsd_stat_shutdown();
 	nfsd_lockd_shutdown();
 	nfsd4_free_slabs();
 	nfsd4_exit_pnfs();
-	unregister_filesystem(&nfsd_fs_type);
-	unregister_cld_notifier();
 }
 
 MODULE_AUTHOR("Olaf Kirch <okir@monad.swb.de>");
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfsd.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfsd.h
@@ -64,12 +64,12 @@
 
 
 extern struct svc_program	nfsd_program;
-extern const struct svc_version	nfsd_version2, nfsd_version3,
-				nfsd_version4;
+extern const struct svc_version	nfsd_version2, nfsd_version3, nfsd_version4;
 extern struct mutex		nfsd_mutex;
 extern spinlock_t		nfsd_drc_lock;
 extern unsigned long		nfsd_drc_max_mem;
 extern unsigned long		nfsd_drc_mem_used;
+extern atomic_t			nfsd_th_cnt;		/* number of available threads */
 
 extern const struct seq_operations nfs_exports_op;
 
@@ -78,8 +78,10 @@
  */
 struct nfsd_voidargs { };
 struct nfsd_voidres { };
-int		nfssvc_decode_voidarg(struct svc_rqst *rqstp, __be32 *p);
-int		nfssvc_encode_voidres(struct svc_rqst *rqstp, __be32 *p);
+bool		nfssvc_decode_voidarg(struct svc_rqst *rqstp,
+				      struct xdr_stream *xdr);
+bool		nfssvc_encode_voidres(struct svc_rqst *rqstp,
+				      struct xdr_stream *xdr);
 
 /*
  * Function prototypes.
@@ -95,8 +97,6 @@
 int		nfsd_pool_stats_release(struct inode *, struct file *);
 void		nfsd_shutdown_threads(struct net *net);
 
-void		nfsd_destroy(struct net *net);
-
 bool		i_am_nfsd(void);
 
 struct nfsdfs_client {
@@ -132,6 +132,7 @@
 int nfsd_minorversion(struct nfsd_net *nn, u32 minorversion, enum vers_op change);
 void nfsd_reset_versions(struct nfsd_net *nn);
 int nfsd_create_serv(struct net *net);
+void nfsd_last_thread(struct net *net);
 
 extern int nfsd_max_blksize;
 
@@ -160,6 +161,9 @@
 int nfs4_reset_recoverydir(char *recdir);
 char * nfs4_recoverydir(void);
 bool nfsd4_spo_must_allow(struct svc_rqst *rqstp);
+int nfsd4_create_laundry_wq(void);
+void nfsd4_destroy_laundry_wq(void);
+bool nfsd_wait_for_delegreturn(struct svc_rqst *rqstp, struct inode *inode);
 #else
 static inline int nfsd4_init_slabs(void) { return 0; }
 static inline void nfsd4_free_slabs(void) { }
@@ -173,6 +177,13 @@
 {
 	return false;
 }
+static inline int nfsd4_create_laundry_wq(void) { return 0; };
+static inline void nfsd4_destroy_laundry_wq(void) {};
+static inline bool nfsd_wait_for_delegreturn(struct svc_rqst *rqstp,
+					      struct inode *inode)
+{
+	return false;
+}
 #endif
 
 /*
@@ -334,6 +345,10 @@
 #define COMPOUND_ERR_SLACK_SPACE	16     /* OP_SETATTR */
 
 #define NFSD_LAUNDROMAT_MINTIMEOUT      1   /* seconds */
+#define	NFSD_COURTESY_CLIENT_TIMEOUT	(24 * 60 * 60)	/* seconds */
+#define	NFSD_CLIENT_MAX_TRIM_PER_RUN	128
+#define	NFS4_CLIENTS_PER_GB		1024
+#define NFSD_DELEGRETURN_TIMEOUT	(HZ / 34)	/* 30ms */
 
 /*
  * The following attributes are currently not supported by the NFSv4 server:
@@ -362,7 +377,7 @@
  | FATTR4_WORD1_OWNER	        | FATTR4_WORD1_OWNER_GROUP  | FATTR4_WORD1_RAWDEV           \
  | FATTR4_WORD1_SPACE_AVAIL     | FATTR4_WORD1_SPACE_FREE   | FATTR4_WORD1_SPACE_TOTAL      \
  | FATTR4_WORD1_SPACE_USED      | FATTR4_WORD1_TIME_ACCESS  | FATTR4_WORD1_TIME_ACCESS_SET  \
- | FATTR4_WORD1_TIME_DELTA   | FATTR4_WORD1_TIME_METADATA    \
+ | FATTR4_WORD1_TIME_DELTA      | FATTR4_WORD1_TIME_METADATA   | FATTR4_WORD1_TIME_CREATE      \
  | FATTR4_WORD1_TIME_MODIFY     | FATTR4_WORD1_TIME_MODIFY_SET | FATTR4_WORD1_MOUNTED_ON_FILEID)
 
 #define NFSD4_SUPPORTED_ATTRS_WORD2 0
@@ -458,7 +473,8 @@
 	(FATTR4_WORD0_SIZE | FATTR4_WORD0_ACL)
 #define NFSD_WRITEABLE_ATTRS_WORD1 \
 	(FATTR4_WORD1_MODE | FATTR4_WORD1_OWNER | FATTR4_WORD1_OWNER_GROUP \
-	| FATTR4_WORD1_TIME_ACCESS_SET | FATTR4_WORD1_TIME_MODIFY_SET)
+	| FATTR4_WORD1_TIME_ACCESS_SET | FATTR4_WORD1_TIME_CREATE \
+	| FATTR4_WORD1_TIME_MODIFY_SET)
 #ifdef CONFIG_NFSD_V4_SECURITY_LABEL
 #define MAYBE_FATTR4_WORD2_SECURITY_LABEL \
 	FATTR4_WORD2_SECURITY_LABEL
@@ -488,12 +504,16 @@
 extern void nfsd4_ssc_init_umount_work(struct nfsd_net *nn);
 #endif
 
+extern void nfsd4_init_leases_net(struct nfsd_net *nn);
+
 #else /* CONFIG_NFSD_V4 */
 static inline int nfsd4_is_junction(struct dentry *dentry)
 {
 	return 0;
 }
 
+static inline void nfsd4_init_leases_net(struct nfsd_net *nn) { };
+
 #define register_cld_notifier() 0
 #define unregister_cld_notifier() do { } while(0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfsfh.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfsfh.c
@@ -154,11 +154,12 @@
 static __be32 nfsd_set_fh_dentry(struct svc_rqst *rqstp, struct svc_fh *fhp)
 {
 	struct knfsd_fh	*fh = &fhp->fh_handle;
-	struct fid *fid = NULL, sfid;
+	struct fid *fid = NULL;
 	struct svc_export *exp;
 	struct dentry *dentry;
 	int fileid_type;
 	int data_left = fh->fh_size/4;
+	int len;
 	__be32 error;
 
 	error = nfserr_stale;
@@ -167,48 +168,35 @@
 	if (rqstp->rq_vers == 4 && fh->fh_size == 0)
 		return nfserr_nofilehandle;
 
-	if (fh->fh_version == 1) {
-		int len;
+	if (fh->fh_version != 1)
+		return error;
 
-		if (--data_left < 0)
-			return error;
-		if (fh->fh_auth_type != 0)
-			return error;
-		len = key_len(fh->fh_fsid_type) / 4;
-		if (len == 0)
-			return error;
-		if  (fh->fh_fsid_type == FSID_MAJOR_MINOR) {
-			/* deprecated, convert to type 3 */
-			len = key_len(FSID_ENCODE_DEV)/4;
-			fh->fh_fsid_type = FSID_ENCODE_DEV;
-			/*
-			 * struct knfsd_fh uses host-endian fields, which are
-			 * sometimes used to hold net-endian values. This
-			 * confuses sparse, so we must use __force here to
-			 * keep it from complaining.
-			 */
-			fh->fh_fsid[0] = new_encode_dev(MKDEV(ntohl((__force __be32)fh->fh_fsid[0]),
-							ntohl((__force __be32)fh->fh_fsid[1])));
-			fh->fh_fsid[1] = fh->fh_fsid[2];
-		}
-		data_left -= len;
-		if (data_left < 0)
-			return error;
-		exp = rqst_exp_find(rqstp, fh->fh_fsid_type, fh->fh_fsid);
-		fid = (struct fid *)(fh->fh_fsid + len);
-	} else {
-		__u32 tfh[2];
-		dev_t xdev;
-		ino_t xino;
-
-		if (fh->fh_size != NFS_FHSIZE)
-			return error;
-		/* assume old filehandle format */
-		xdev = old_decode_dev(fh->ofh_xdev);
-		xino = u32_to_ino_t(fh->ofh_xino);
-		mk_fsid(FSID_DEV, tfh, xdev, xino, 0, NULL);
-		exp = rqst_exp_find(rqstp, FSID_DEV, tfh);
-	}
+	if (--data_left < 0)
+		return error;
+	if (fh->fh_auth_type != 0)
+		return error;
+	len = key_len(fh->fh_fsid_type) / 4;
+	if (len == 0)
+		return error;
+	if (fh->fh_fsid_type == FSID_MAJOR_MINOR) {
+		/* deprecated, convert to type 3 */
+		len = key_len(FSID_ENCODE_DEV)/4;
+		fh->fh_fsid_type = FSID_ENCODE_DEV;
+		/*
+		 * struct knfsd_fh uses host-endian fields, which are
+		 * sometimes used to hold net-endian values. This
+		 * confuses sparse, so we must use __force here to
+		 * keep it from complaining.
+		 */
+		fh->fh_fsid[0] = new_encode_dev(MKDEV(ntohl((__force __be32)fh->fh_fsid[0]),
+						      ntohl((__force __be32)fh->fh_fsid[1])));
+		fh->fh_fsid[1] = fh->fh_fsid[2];
+	}
+	data_left -= len;
+	if (data_left < 0)
+		return error;
+	exp = rqst_exp_find(rqstp, fh->fh_fsid_type, fh->fh_fsid);
+	fid = (struct fid *)(fh->fh_fsid + len);
 
 	error = nfserr_stale;
 	if (IS_ERR(exp)) {
@@ -253,18 +241,7 @@
 	if (rqstp->rq_vers > 2)
 		error = nfserr_badhandle;
 
-	if (fh->fh_version != 1) {
-		sfid.i32.ino = fh->ofh_ino;
-		sfid.i32.gen = fh->ofh_generation;
-		sfid.i32.parent_ino = fh->ofh_dirino;
-		fid = &sfid;
-		data_left = 3;
-		if (fh->ofh_dirino == 0)
-			fileid_type = FILEID_INO32_GEN;
-		else
-			fileid_type = FILEID_INO32_GEN_PARENT;
-	} else
-		fileid_type = fh->fh_fileid_type;
+	fileid_type = fh->fh_fileid_type;
 
 	if (fileid_type == FILEID_ROOT)
 		dentry = dget(exp->ex_path.dentry);
@@ -350,12 +327,11 @@
 __be32
 fh_verify(struct svc_rqst *rqstp, struct svc_fh *fhp, umode_t type, int access)
 {
+	struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 	struct svc_export *exp = NULL;
 	struct dentry	*dentry;
 	__be32		error;
 
-	dprintk("nfsd: fh_verify(%s)\n", SVCFH_fmt(fhp));
-
 	if (!fhp->fh_dentry) {
 		error = nfsd_set_fh_dentry(rqstp, fhp);
 		if (error)
@@ -363,6 +339,9 @@
 	}
 	dentry = fhp->fh_dentry;
 	exp = fhp->fh_export;
+
+	trace_nfsd_fh_verify(rqstp, fhp, type, access);
+
 	/*
 	 * We still have to do all these permission checks, even when
 	 * fh_dentry is already set:
@@ -414,16 +393,10 @@
 skip_pseudoflavor_check:
 	/* Finally, check access permissions. */
 	error = nfsd_permission(rqstp, exp, dentry, access);
-
-	if (error) {
-		dprintk("fh_verify: %pd2 permission failure, "
-			"acc=%x, error=%d\n",
-			dentry,
-			access, ntohl(error));
-	}
 out:
+	trace_nfsd_fh_verify_err(rqstp, fhp, type, access, error);
 	if (error == nfserr_stale)
-		nfsd_stats_fh_stale_inc(exp);
+		nfsd_stats_fh_stale_inc(nn, exp);
 	return error;
 }
 
@@ -452,20 +425,6 @@
 	}
 }
 
-/*
- * for composing old style file handles
- */
-static inline void _fh_update_old(struct dentry *dentry,
-				  struct svc_export *exp,
-				  struct knfsd_fh *fh)
-{
-	fh->ofh_ino = ino_t_to_u32(d_inode(dentry)->i_ino);
-	fh->ofh_generation = d_inode(dentry)->i_generation;
-	if (d_is_dir(dentry) ||
-	    (exp->ex_flags & NFSEXP_NOSUBTREECHECK))
-		fh->ofh_dirino = 0;
-}
-
 static bool is_root_export(struct svc_export *exp)
 {
 	return exp->ex_path.dentry == exp->ex_path.dentry->d_sb->s_root;
@@ -562,9 +521,6 @@
 	/* ref_fh is a reference file handle.
 	 * if it is non-null and for the same filesystem, then we should compose
 	 * a filehandle which is of the same version, where possible.
-	 * Currently, that means that if ref_fh->fh_handle.fh_version == 0xca
-	 * Then create a 32byte filehandle using nfs_fhbase_old
-	 *
 	 */
 
 	struct inode * inode = d_inode(dentry);
@@ -588,7 +544,7 @@
 	if (ref_fh == fhp)
 		fh_put(ref_fh);
 
-	if (fhp->fh_locked || fhp->fh_dentry) {
+	if (fhp->fh_dentry) {
 		printk(KERN_ERR "fh_compose: fh %pd2 not initialized!\n",
 		       dentry);
 	}
@@ -600,35 +556,21 @@
 	fhp->fh_dentry = dget(dentry); /* our internal copy */
 	fhp->fh_export = exp_get(exp);
 
-	if (fhp->fh_handle.fh_version == 0xca) {
-		/* old style filehandle please */
-		memset(&fhp->fh_handle.fh_base, 0, NFS_FHSIZE);
-		fhp->fh_handle.fh_size = NFS_FHSIZE;
-		fhp->fh_handle.ofh_dcookie = 0xfeebbaca;
-		fhp->fh_handle.ofh_dev =  old_encode_dev(ex_dev);
-		fhp->fh_handle.ofh_xdev = fhp->fh_handle.ofh_dev;
-		fhp->fh_handle.ofh_xino =
-			ino_t_to_u32(d_inode(exp->ex_path.dentry)->i_ino);
-		fhp->fh_handle.ofh_dirino = ino_t_to_u32(parent_ino(dentry));
-		if (inode)
-			_fh_update_old(dentry, exp, &fhp->fh_handle);
-	} else {
-		fhp->fh_handle.fh_size =
-			key_len(fhp->fh_handle.fh_fsid_type) + 4;
-		fhp->fh_handle.fh_auth_type = 0;
-
-		mk_fsid(fhp->fh_handle.fh_fsid_type,
-			fhp->fh_handle.fh_fsid,
-			ex_dev,
-			d_inode(exp->ex_path.dentry)->i_ino,
-			exp->ex_fsid, exp->ex_uuid);
-
-		if (inode)
-			_fh_update(fhp, exp, dentry);
-		if (fhp->fh_handle.fh_fileid_type == FILEID_INVALID) {
-			fh_put(fhp);
-			return nfserr_opnotsupp;
-		}
+	fhp->fh_handle.fh_size =
+		key_len(fhp->fh_handle.fh_fsid_type) + 4;
+	fhp->fh_handle.fh_auth_type = 0;
+
+	mk_fsid(fhp->fh_handle.fh_fsid_type,
+		fhp->fh_handle.fh_fsid,
+		ex_dev,
+		d_inode(exp->ex_path.dentry)->i_ino,
+		exp->ex_fsid, exp->ex_uuid);
+
+	if (inode)
+		_fh_update(fhp, exp, dentry);
+	if (fhp->fh_handle.fh_fileid_type == FILEID_INVALID) {
+		fh_put(fhp);
+		return nfserr_stale;
 	}
 
 	return 0;
@@ -649,16 +591,12 @@
 	dentry = fhp->fh_dentry;
 	if (d_really_is_negative(dentry))
 		goto out_negative;
-	if (fhp->fh_handle.fh_version != 1) {
-		_fh_update_old(dentry, fhp->fh_export, &fhp->fh_handle);
-	} else {
-		if (fhp->fh_handle.fh_fileid_type != FILEID_ROOT)
-			return 0;
+	if (fhp->fh_handle.fh_fileid_type != FILEID_ROOT)
+		return 0;
 
-		_fh_update(fhp, fhp->fh_export, dentry);
-		if (fhp->fh_handle.fh_fileid_type == FILEID_INVALID)
-			return nfserr_opnotsupp;
-	}
+	_fh_update(fhp, fhp->fh_export, dentry);
+	if (fhp->fh_handle.fh_fileid_type == FILEID_INVALID)
+		return nfserr_stale;
 	return 0;
 out_bad:
 	printk(KERN_ERR "fh_update: fh not verified!\n");
@@ -669,6 +607,85 @@
 	return nfserr_serverfault;
 }
 
+/**
+ * fh_fill_pre_attrs - Fill in pre-op attributes
+ * @fhp: file handle to be updated
+ *
+ */
+void fh_fill_pre_attrs(struct svc_fh *fhp)
+{
+	bool v4 = (fhp->fh_maxsize == NFS4_FHSIZE);
+	struct inode *inode;
+	struct kstat stat;
+	__be32 err;
+
+	if (fhp->fh_no_wcc || fhp->fh_pre_saved)
+		return;
+
+	inode = d_inode(fhp->fh_dentry);
+	err = fh_getattr(fhp, &stat);
+	if (err) {
+		/* Grab the times from inode anyway */
+		stat.mtime = inode->i_mtime;
+		stat.ctime = inode->i_ctime;
+		stat.size  = inode->i_size;
+	}
+	if (v4)
+		fhp->fh_pre_change = nfsd4_change_attribute(&stat, inode);
+
+	fhp->fh_pre_mtime = stat.mtime;
+	fhp->fh_pre_ctime = stat.ctime;
+	fhp->fh_pre_size  = stat.size;
+	fhp->fh_pre_saved = true;
+}
+
+/**
+ * fh_fill_post_attrs - Fill in post-op attributes
+ * @fhp: file handle to be updated
+ *
+ */
+void fh_fill_post_attrs(struct svc_fh *fhp)
+{
+	bool v4 = (fhp->fh_maxsize == NFS4_FHSIZE);
+	struct inode *inode = d_inode(fhp->fh_dentry);
+	__be32 err;
+
+	if (fhp->fh_no_wcc)
+		return;
+
+	if (fhp->fh_post_saved)
+		printk("nfsd: inode locked twice during operation.\n");
+
+	err = fh_getattr(fhp, &fhp->fh_post_attr);
+	if (err) {
+		fhp->fh_post_saved = false;
+		fhp->fh_post_attr.ctime = inode->i_ctime;
+	} else
+		fhp->fh_post_saved = true;
+	if (v4)
+		fhp->fh_post_change =
+			nfsd4_change_attribute(&fhp->fh_post_attr, inode);
+}
+
+/**
+ * fh_fill_both_attrs - Fill pre-op and post-op attributes
+ * @fhp: file handle to be updated
+ *
+ * This is used when the directory wasn't changed, but wcc attributes
+ * are needed anyway.
+ */
+void fh_fill_both_attrs(struct svc_fh *fhp)
+{
+	fh_fill_post_attrs(fhp);
+	if (!fhp->fh_post_saved)
+		return;
+	fhp->fh_pre_change = fhp->fh_post_change;
+	fhp->fh_pre_mtime = fhp->fh_post_attr.mtime;
+	fhp->fh_pre_ctime = fhp->fh_post_attr.ctime;
+	fhp->fh_pre_size = fhp->fh_post_attr.size;
+	fhp->fh_pre_saved = true;
+}
+
 /*
  * Release a file handle.
  */
@@ -678,10 +695,9 @@
 	struct dentry * dentry = fhp->fh_dentry;
 	struct svc_export * exp = fhp->fh_export;
 	if (dentry) {
-		fh_unlock(fhp);
 		fhp->fh_dentry = NULL;
 		dput(dentry);
-		fh_clear_wcc(fhp);
+		fh_clear_pre_post_attrs(fhp);
 	}
 	fh_drop_write(fhp);
 	if (exp) {
@@ -698,16 +714,11 @@
 char * SVCFH_fmt(struct svc_fh *fhp)
 {
 	struct knfsd_fh *fh = &fhp->fh_handle;
+	static char buf[2+1+1+64*3+1];
 
-	static char buf[80];
-	sprintf(buf, "%d: %08x %08x %08x %08x %08x %08x",
-		fh->fh_size,
-		fh->fh_base.fh_pad[0],
-		fh->fh_base.fh_pad[1],
-		fh->fh_base.fh_pad[2],
-		fh->fh_base.fh_pad[3],
-		fh->fh_base.fh_pad[4],
-		fh->fh_base.fh_pad[5]);
+	if (fh->fh_size < 0 || fh->fh_size> 64)
+		return "bad-fh";
+	sprintf(buf, "%d: %*ph", fh->fh_size, fh->fh_size, fh->fh_raw);
 	return buf;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfsfh.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfsfh.h
@@ -10,9 +10,56 @@
 
 #include <linux/crc32.h>
 #include <linux/sunrpc/svc.h>
-#include <uapi/linux/nfsd/nfsfh.h>
 #include <linux/iversion.h>
 #include <linux/exportfs.h>
+#include <linux/nfs4.h>
+
+/*
+ * The file handle starts with a sequence of four-byte words.
+ * The first word contains a version number (1) and three descriptor bytes
+ * that tell how the remaining 3 variable length fields should be handled.
+ * These three bytes are auth_type, fsid_type and fileid_type.
+ *
+ * All four-byte values are in host-byte-order.
+ *
+ * The auth_type field is deprecated and must be set to 0.
+ *
+ * The fsid_type identifies how the filesystem (or export point) is
+ *    encoded.
+ *  Current values:
+ *     0  - 4 byte device id (ms-2-bytes major, ls-2-bytes minor), 4byte inode number
+ *        NOTE: we cannot use the kdev_t device id value, because kdev_t.h
+ *              says we mustn't.  We must break it up and reassemble.
+ *     1  - 4 byte user specified identifier
+ *     2  - 4 byte major, 4 byte minor, 4 byte inode number - DEPRECATED
+ *     3  - 4 byte device id, encoded for user-space, 4 byte inode number
+ *     4  - 4 byte inode number and 4 byte uuid
+ *     5  - 8 byte uuid
+ *     6  - 16 byte uuid
+ *     7  - 8 byte inode number and 16 byte uuid
+ *
+ * The fileid_type identifies how the file within the filesystem is encoded.
+ *   The values for this field are filesystem specific, exccept that
+ *   filesystems must not use the values '0' or '0xff'. 'See enum fid_type'
+ *   in include/linux/exportfs.h for currently registered values.
+ */
+
+struct knfsd_fh {
+	unsigned int	fh_size;	/*
+					 * Points to the current size while
+					 * building a new file handle.
+					 */
+	union {
+		char			fh_raw[NFS4_FHSIZE];
+		struct {
+			u8		fh_version;	/* == 1 */
+			u8		fh_auth_type;	/* deprecated */
+			u8		fh_fsid_type;
+			u8		fh_fileid_type;
+			u32		fh_fsid[]; /* flexible-array member */
+		};
+	};
+};
 
 static inline __u32 ino_t_to_u32(ino_t ino)
 {
@@ -34,7 +81,6 @@
 	struct dentry *		fh_dentry;	/* validated dentry */
 	struct svc_export *	fh_export;	/* export pointer */
 
-	bool			fh_locked;	/* inode locked by us */
 	bool			fh_want_write;	/* remount protection taken */
 	bool			fh_no_wcc;	/* no wcc data needed */
 	bool			fh_no_atomic_attr;
@@ -43,11 +89,10 @@
 						 * operation
 						 */
 	int			fh_flags;	/* FH flags */
-#ifdef CONFIG_NFSD_V3
 	bool			fh_post_saved;	/* post-op attrs saved */
 	bool			fh_pre_saved;	/* pre-op attrs saved */
 
-	/* Pre-op attributes saved during fh_lock */
+	/* Pre-op attributes saved when inode is locked */
 	__u64			fh_pre_size;	/* size before operation */
 	struct timespec64	fh_pre_mtime;	/* mtime before oper */
 	struct timespec64	fh_pre_ctime;	/* ctime before oper */
@@ -57,10 +102,9 @@
 	 */
 	u64			fh_pre_change;
 
-	/* Post-op attributes saved in fh_unlock */
+	/* Post-op attributes saved in fh_fill_post_attrs() */
 	struct kstat		fh_post_attr;	/* full attrs after operation */
 	u64			fh_post_change; /* nfsv4 change; see above */
-#endif /* CONFIG_NFSD_V3 */
 } svc_fh;
 #define NFSD4_FH_FOREIGN (1<<0)
 #define SET_FH_FLAG(c, f) ((c)->fh_flags |= (f))
@@ -176,19 +220,19 @@
 void	fh_put(struct svc_fh *);
 
 static __inline__ struct svc_fh *
-fh_copy(struct svc_fh *dst, struct svc_fh *src)
+fh_copy(struct svc_fh *dst, const struct svc_fh *src)
 {
-	WARN_ON(src->fh_dentry || src->fh_locked);
-			
+	WARN_ON(src->fh_dentry);
+
 	*dst = *src;
 	return dst;
 }
 
 static inline void
-fh_copy_shallow(struct knfsd_fh *dst, struct knfsd_fh *src)
+fh_copy_shallow(struct knfsd_fh *dst, const struct knfsd_fh *src)
 {
 	dst->fh_size = src->fh_size;
-	memcpy(&dst->fh_base, &src->fh_base, src->fh_size);
+	memcpy(&dst->fh_raw, &src->fh_raw, src->fh_size);
 }
 
 static __inline__ struct svc_fh *
@@ -199,16 +243,18 @@
 	return fhp;
 }
 
-static inline bool fh_match(struct knfsd_fh *fh1, struct knfsd_fh *fh2)
+static inline bool fh_match(const struct knfsd_fh *fh1,
+			    const struct knfsd_fh *fh2)
 {
 	if (fh1->fh_size != fh2->fh_size)
 		return false;
-	if (memcmp(fh1->fh_base.fh_pad, fh2->fh_base.fh_pad, fh1->fh_size) != 0)
+	if (memcmp(fh1->fh_raw, fh2->fh_raw, fh1->fh_size) != 0)
 		return false;
 	return true;
 }
 
-static inline bool fh_fsid_match(struct knfsd_fh *fh1, struct knfsd_fh *fh2)
+static inline bool fh_fsid_match(const struct knfsd_fh *fh1,
+				 const struct knfsd_fh *fh2)
 {
 	if (fh1->fh_fsid_type != fh2->fh_fsid_type)
 		return false;
@@ -227,7 +273,7 @@
  */
 static inline u32 knfsd_fh_hash(const struct knfsd_fh *fh)
 {
-	return ~crc32_le(0xFFFFFFFF, (unsigned char *)&fh->fh_base, fh->fh_size);
+	return ~crc32_le(0xFFFFFFFF, fh->fh_raw, fh->fh_size);
 }
 #else
 static inline u32 knfsd_fh_hash(const struct knfsd_fh *fh)
@@ -236,13 +282,12 @@
 }
 #endif
 
-#ifdef CONFIG_NFSD_V3
-/*
- * The wcc data stored in current_fh should be cleared
- * between compound ops.
+/**
+ * fh_clear_pre_post_attrs - Reset pre/post attributes
+ * @fhp: file handle to be updated
+ *
  */
-static inline void
-fh_clear_wcc(struct svc_fh *fhp)
+static inline void fh_clear_pre_post_attrs(struct svc_fh *fhp)
 {
 	fhp->fh_post_saved = false;
 	fhp->fh_pre_saved = false;
@@ -276,59 +321,7 @@
 		return time_to_chattr(&stat->ctime);
 }
 
-extern void fill_pre_wcc(struct svc_fh *fhp);
-extern void fill_post_wcc(struct svc_fh *fhp);
-#else
-#define fh_clear_wcc(ignored)
-#define fill_pre_wcc(ignored)
-#define fill_post_wcc(notused)
-#endif /* CONFIG_NFSD_V3 */
-
-
-/*
- * Lock a file handle/inode
- * NOTE: both fh_lock and fh_unlock are done "by hand" in
- * vfs.c:nfsd_rename as it needs to grab 2 i_mutex's at once
- * so, any changes here should be reflected there.
- */
-
-static inline void
-fh_lock_nested(struct svc_fh *fhp, unsigned int subclass)
-{
-	struct dentry	*dentry = fhp->fh_dentry;
-	struct inode	*inode;
-
-	BUG_ON(!dentry);
-
-	if (fhp->fh_locked) {
-		printk(KERN_WARNING "fh_lock: %pd2 already locked!\n",
-			dentry);
-		return;
-	}
-
-	inode = d_inode(dentry);
-	inode_lock_nested(inode, subclass);
-	fill_pre_wcc(fhp);
-	fhp->fh_locked = true;
-}
-
-static inline void
-fh_lock(struct svc_fh *fhp)
-{
-	fh_lock_nested(fhp, I_MUTEX_NORMAL);
-}
-
-/*
- * Unlock a file handle/inode
- */
-static inline void
-fh_unlock(struct svc_fh *fhp)
-{
-	if (fhp->fh_locked) {
-		fill_post_wcc(fhp);
-		inode_unlock(d_inode(fhp->fh_dentry));
-		fhp->fh_locked = false;
-	}
-}
-
+extern void fh_fill_pre_attrs(struct svc_fh *fhp);
+extern void fh_fill_post_attrs(struct svc_fh *fhp);
+extern void fh_fill_both_attrs(struct svc_fh *fhp);
 #endif /* _LINUX_NFSD_NFSFH_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfsproc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfsproc.c
@@ -51,6 +51,9 @@
 	struct nfsd_sattrargs *argp = rqstp->rq_argp;
 	struct nfsd_attrstat *resp = rqstp->rq_resp;
 	struct iattr *iap = &argp->attrs;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= iap,
+	};
 	struct svc_fh *fhp;
 
 	dprintk("nfsd: SETATTR  %s, valid=%x, size=%ld\n",
@@ -100,7 +103,7 @@
 		}
 	}
 
-	resp->status = nfsd_setattr(rqstp, fhp, iap, 0, (time64_t)0);
+	resp->status = nfsd_setattr(rqstp, fhp, &attrs, 0, (time64_t)0);
 	if (resp->status != nfs_ok)
 		goto out;
 
@@ -182,6 +185,7 @@
 		argp->count, argp->offset);
 
 	argp->count = min_t(u32, argp->count, NFSSVC_MAXBLKSIZE_V2);
+	argp->count = min_t(u32, argp->count, rqstp->rq_res.buflen);
 
 	v = 0;
 	len = argp->count;
@@ -207,7 +211,7 @@
 	if (resp->status == nfs_ok)
 		resp->status = fh_getattr(&resp->fh, &resp->stat);
 	else if (resp->status == nfserr_jukebox)
-		return rpc_drop_reply;
+		set_bit(RQ_DROPME, &rqstp->rq_flags);
 	return rpc_success;
 }
 
@@ -230,16 +234,11 @@
 	unsigned long cnt = argp->len;
 	unsigned int nvecs;
 
-	dprintk("nfsd: WRITE    %s %d bytes at %d\n",
+	dprintk("nfsd: WRITE    %s %u bytes at %d\n",
 		SVCFH_fmt(&argp->fh),
 		argp->len, argp->offset);
 
-	nvecs = svc_fill_write_vector(rqstp, rqstp->rq_arg.pages,
-				      &argp->first, cnt);
-	if (!nvecs) {
-		resp->status = nfserr_io;
-		goto out;
-	}
+	nvecs = svc_fill_write_vector(rqstp, &argp->payload);
 
 	resp->status = nfsd_write(rqstp, fh_copy(&resp->fh, &argp->fh),
 				  argp->offset, rqstp->rq_vec, nvecs,
@@ -247,8 +246,7 @@
 	if (resp->status == nfs_ok)
 		resp->status = fh_getattr(&resp->fh, &resp->stat);
 	else if (resp->status == nfserr_jukebox)
-		return rpc_drop_reply;
-out:
+		set_bit(RQ_DROPME, &rqstp->rq_flags);
 	return rpc_success;
 }
 
@@ -266,6 +264,9 @@
 	svc_fh		*dirfhp = &argp->fh;
 	svc_fh		*newfhp = &resp->fh;
 	struct iattr	*attr = &argp->attrs;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= attr,
+	};
 	struct inode	*inode;
 	struct dentry	*dchild;
 	int		type, mode;
@@ -291,7 +292,7 @@
 		goto done;
 	}
 
-	fh_lock_nested(dirfhp, I_MUTEX_PARENT);
+	inode_lock_nested(dirfhp->fh_dentry->d_inode, I_MUTEX_PARENT);
 	dchild = lookup_one_len(argp->name, dirfhp->fh_dentry, argp->len);
 	if (IS_ERR(dchild)) {
 		resp->status = nfserrno(PTR_ERR(dchild));
@@ -390,9 +391,8 @@
 	resp->status = nfs_ok;
 	if (!inode) {
 		/* File doesn't exist. Create it and set attrs */
-		resp->status = nfsd_create_locked(rqstp, dirfhp, argp->name,
-						  argp->len, attr, type, rdev,
-						  newfhp);
+		resp->status = nfsd_create_locked(rqstp, dirfhp, &attrs, type,
+						  rdev, newfhp);
 	} else if (type == S_IFREG) {
 		dprintk("nfsd:   existing %s, valid=%x, size=%ld\n",
 			argp->name, attr->ia_valid, (long) attr->ia_size);
@@ -402,13 +402,12 @@
 		 */
 		attr->ia_valid &= ATTR_SIZE;
 		if (attr->ia_valid)
-			resp->status = nfsd_setattr(rqstp, newfhp, attr, 0,
+			resp->status = nfsd_setattr(rqstp, newfhp, &attrs, 0,
 						    (time64_t)0);
 	}
 
 out_unlock:
-	/* We don't really need to unlock, as fh_put does it. */
-	fh_unlock(dirfhp);
+	inode_unlock(dirfhp->fh_dentry->d_inode);
 	fh_drop_write(dirfhp);
 done:
 	fh_put(dirfhp);
@@ -478,6 +477,9 @@
 {
 	struct nfsd_symlinkargs *argp = rqstp->rq_argp;
 	struct nfsd_stat *resp = rqstp->rq_resp;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &argp->attrs,
+	};
 	struct svc_fh	newfh;
 
 	if (argp->tlen > NFS_MAXPATHLEN) {
@@ -499,7 +501,7 @@
 
 	fh_init(&newfh, NFS_FHSIZE);
 	resp->status = nfsd_symlink(rqstp, &argp->ffh, argp->fname, argp->flen,
-				    argp->tname, &newfh);
+				    argp->tname, &attrs, &newfh);
 
 	kfree(argp->tname);
 	fh_put(&argp->ffh);
@@ -517,6 +519,9 @@
 {
 	struct nfsd_createargs *argp = rqstp->rq_argp;
 	struct nfsd_diropres *resp = rqstp->rq_resp;
+	struct nfsd_attrs attrs = {
+		.na_iattr	= &argp->attrs,
+	};
 
 	dprintk("nfsd: MKDIR    %s %.*s\n", SVCFH_fmt(&argp->fh), argp->len, argp->name);
 
@@ -528,7 +533,7 @@
 	argp->attrs.ia_valid &= ~ATTR_SIZE;
 	fh_init(&resp->fh, NFS_FHSIZE);
 	resp->status = nfsd_create(rqstp, &argp->fh, argp->name, argp->len,
-				   &argp->attrs, S_IFDIR, 0, &resp->fh);
+				   &attrs, S_IFDIR, 0, &resp->fh);
 	fh_put(&argp->fh);
 	if (resp->status != nfs_ok)
 		goto out;
@@ -557,29 +562,20 @@
 
 static void nfsd_init_dirlist_pages(struct svc_rqst *rqstp,
 				    struct nfsd_readdirres *resp,
-				    int count)
+				    u32 count)
 {
 	struct xdr_buf *buf = &resp->dirlist;
 	struct xdr_stream *xdr = &resp->xdr;
 
-	count = min_t(u32, count, PAGE_SIZE);
-
 	memset(buf, 0, sizeof(*buf));
 
 	/* Reserve room for the NULL ptr & eof flag (-2 words) */
-	buf->buflen = count - sizeof(__be32) * 2;
+	buf->buflen = clamp(count, (u32)(XDR_UNIT * 2), (u32)PAGE_SIZE);
+	buf->buflen -= XDR_UNIT * 2;
 	buf->pages = rqstp->rq_next_page;
 	rqstp->rq_next_page++;
 
-	/* This is xdr_init_encode(), but it assumes that
-	 * the head kvec has already been consumed. */
-	xdr_set_scratch_buffer(xdr, NULL, 0);
-	xdr->buf = buf;
-	xdr->page_ptr = buf->pages;
-	xdr->iov = NULL;
-	xdr->p = page_address(*buf->pages);
-	xdr->end = xdr->p + (PAGE_SIZE >> 2);
-	xdr->rqst = NULL;
+	xdr_init_encode_pages(xdr, buf, buf->pages,  NULL);
 }
 
 /*
@@ -641,6 +637,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = 0,
@@ -652,6 +649,7 @@
 		.pc_encode = nfssvc_encode_attrstatres,
 		.pc_release = nfssvc_release_attrstat,
 		.pc_argsize = sizeof(struct nfsd_fhandle),
+		.pc_argzero = sizeof(struct nfsd_fhandle),
 		.pc_ressize = sizeof(struct nfsd_attrstat),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+AT,
@@ -663,6 +661,7 @@
 		.pc_encode = nfssvc_encode_attrstatres,
 		.pc_release = nfssvc_release_attrstat,
 		.pc_argsize = sizeof(struct nfsd_sattrargs),
+		.pc_argzero = sizeof(struct nfsd_sattrargs),
 		.pc_ressize = sizeof(struct nfsd_attrstat),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+AT,
@@ -673,6 +672,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = 0,
@@ -684,6 +684,7 @@
 		.pc_encode = nfssvc_encode_diropres,
 		.pc_release = nfssvc_release_diropres,
 		.pc_argsize = sizeof(struct nfsd_diropargs),
+		.pc_argzero = sizeof(struct nfsd_diropargs),
 		.pc_ressize = sizeof(struct nfsd_diropres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+FH+AT,
@@ -694,6 +695,7 @@
 		.pc_decode = nfssvc_decode_fhandleargs,
 		.pc_encode = nfssvc_encode_readlinkres,
 		.pc_argsize = sizeof(struct nfsd_fhandle),
+		.pc_argzero = sizeof(struct nfsd_fhandle),
 		.pc_ressize = sizeof(struct nfsd_readlinkres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+1+NFS_MAXPATHLEN/4,
@@ -705,6 +707,7 @@
 		.pc_encode = nfssvc_encode_readres,
 		.pc_release = nfssvc_release_readres,
 		.pc_argsize = sizeof(struct nfsd_readargs),
+		.pc_argzero = sizeof(struct nfsd_readargs),
 		.pc_ressize = sizeof(struct nfsd_readres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+AT+1+NFSSVC_MAXBLKSIZE_V2/4,
@@ -715,6 +718,7 @@
 		.pc_decode = nfssvc_decode_voidarg,
 		.pc_encode = nfssvc_encode_voidres,
 		.pc_argsize = sizeof(struct nfsd_voidargs),
+		.pc_argzero = sizeof(struct nfsd_voidargs),
 		.pc_ressize = sizeof(struct nfsd_voidres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = 0,
@@ -726,6 +730,7 @@
 		.pc_encode = nfssvc_encode_attrstatres,
 		.pc_release = nfssvc_release_attrstat,
 		.pc_argsize = sizeof(struct nfsd_writeargs),
+		.pc_argzero = sizeof(struct nfsd_writeargs),
 		.pc_ressize = sizeof(struct nfsd_attrstat),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+AT,
@@ -737,6 +742,7 @@
 		.pc_encode = nfssvc_encode_diropres,
 		.pc_release = nfssvc_release_diropres,
 		.pc_argsize = sizeof(struct nfsd_createargs),
+		.pc_argzero = sizeof(struct nfsd_createargs),
 		.pc_ressize = sizeof(struct nfsd_diropres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+FH+AT,
@@ -747,6 +753,7 @@
 		.pc_decode = nfssvc_decode_diropargs,
 		.pc_encode = nfssvc_encode_statres,
 		.pc_argsize = sizeof(struct nfsd_diropargs),
+		.pc_argzero = sizeof(struct nfsd_diropargs),
 		.pc_ressize = sizeof(struct nfsd_stat),
 		.pc_cachetype = RC_REPLSTAT,
 		.pc_xdrressize = ST,
@@ -757,6 +764,7 @@
 		.pc_decode = nfssvc_decode_renameargs,
 		.pc_encode = nfssvc_encode_statres,
 		.pc_argsize = sizeof(struct nfsd_renameargs),
+		.pc_argzero = sizeof(struct nfsd_renameargs),
 		.pc_ressize = sizeof(struct nfsd_stat),
 		.pc_cachetype = RC_REPLSTAT,
 		.pc_xdrressize = ST,
@@ -767,6 +775,7 @@
 		.pc_decode = nfssvc_decode_linkargs,
 		.pc_encode = nfssvc_encode_statres,
 		.pc_argsize = sizeof(struct nfsd_linkargs),
+		.pc_argzero = sizeof(struct nfsd_linkargs),
 		.pc_ressize = sizeof(struct nfsd_stat),
 		.pc_cachetype = RC_REPLSTAT,
 		.pc_xdrressize = ST,
@@ -777,6 +786,7 @@
 		.pc_decode = nfssvc_decode_symlinkargs,
 		.pc_encode = nfssvc_encode_statres,
 		.pc_argsize = sizeof(struct nfsd_symlinkargs),
+		.pc_argzero = sizeof(struct nfsd_symlinkargs),
 		.pc_ressize = sizeof(struct nfsd_stat),
 		.pc_cachetype = RC_REPLSTAT,
 		.pc_xdrressize = ST,
@@ -788,6 +798,7 @@
 		.pc_encode = nfssvc_encode_diropres,
 		.pc_release = nfssvc_release_diropres,
 		.pc_argsize = sizeof(struct nfsd_createargs),
+		.pc_argzero = sizeof(struct nfsd_createargs),
 		.pc_ressize = sizeof(struct nfsd_diropres),
 		.pc_cachetype = RC_REPLBUFF,
 		.pc_xdrressize = ST+FH+AT,
@@ -798,6 +809,7 @@
 		.pc_decode = nfssvc_decode_diropargs,
 		.pc_encode = nfssvc_encode_statres,
 		.pc_argsize = sizeof(struct nfsd_diropargs),
+		.pc_argzero = sizeof(struct nfsd_diropargs),
 		.pc_ressize = sizeof(struct nfsd_stat),
 		.pc_cachetype = RC_REPLSTAT,
 		.pc_xdrressize = ST,
@@ -808,6 +820,7 @@
 		.pc_decode = nfssvc_decode_readdirargs,
 		.pc_encode = nfssvc_encode_readdirres,
 		.pc_argsize = sizeof(struct nfsd_readdirargs),
+		.pc_argzero = sizeof(struct nfsd_readdirargs),
 		.pc_ressize = sizeof(struct nfsd_readdirres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_name = "READDIR",
@@ -817,6 +830,7 @@
 		.pc_decode = nfssvc_decode_fhandleargs,
 		.pc_encode = nfssvc_encode_statfsres,
 		.pc_argsize = sizeof(struct nfsd_fhandle),
+		.pc_argzero = sizeof(struct nfsd_fhandle),
 		.pc_ressize = sizeof(struct nfsd_statfsres),
 		.pc_cachetype = RC_NOCACHE,
 		.pc_xdrressize = ST+5,
@@ -834,62 +848,3 @@
 	.vs_dispatch	= nfsd_dispatch,
 	.vs_xdrsize	= NFS2_SVC_XDRSIZE,
 };
-
-/*
- * Map errnos to NFS errnos.
- */
-__be32
-nfserrno (int errno)
-{
-	static struct {
-		__be32	nfserr;
-		int	syserr;
-	} nfs_errtbl[] = {
-		{ nfs_ok, 0 },
-		{ nfserr_perm, -EPERM },
-		{ nfserr_noent, -ENOENT },
-		{ nfserr_io, -EIO },
-		{ nfserr_nxio, -ENXIO },
-		{ nfserr_fbig, -E2BIG },
-		{ nfserr_acces, -EACCES },
-		{ nfserr_exist, -EEXIST },
-		{ nfserr_xdev, -EXDEV },
-		{ nfserr_mlink, -EMLINK },
-		{ nfserr_nodev, -ENODEV },
-		{ nfserr_notdir, -ENOTDIR },
-		{ nfserr_isdir, -EISDIR },
-		{ nfserr_inval, -EINVAL },
-		{ nfserr_fbig, -EFBIG },
-		{ nfserr_nospc, -ENOSPC },
-		{ nfserr_rofs, -EROFS },
-		{ nfserr_mlink, -EMLINK },
-		{ nfserr_nametoolong, -ENAMETOOLONG },
-		{ nfserr_notempty, -ENOTEMPTY },
-#ifdef EDQUOT
-		{ nfserr_dquot, -EDQUOT },
-#endif
-		{ nfserr_stale, -ESTALE },
-		{ nfserr_jukebox, -ETIMEDOUT },
-		{ nfserr_jukebox, -ERESTARTSYS },
-		{ nfserr_jukebox, -EAGAIN },
-		{ nfserr_jukebox, -EWOULDBLOCK },
-		{ nfserr_jukebox, -ENOMEM },
-		{ nfserr_io, -ETXTBSY },
-		{ nfserr_notsupp, -EOPNOTSUPP },
-		{ nfserr_toosmall, -ETOOSMALL },
-		{ nfserr_serverfault, -ESERVERFAULT },
-		{ nfserr_serverfault, -ENFILE },
-		{ nfserr_io, -EUCLEAN },
-		{ nfserr_perm, -ENOKEY },
-		{ nfserr_no_grace, -ENOGRACE},
-	};
-	int	i;
-
-	for (i = 0; i < ARRAY_SIZE(nfs_errtbl); i++) {
-		if (nfs_errtbl[i].syserr == errno)
-			return nfs_errtbl[i].nfserr;
-	}
-	WARN_ONCE(1, "nfsd: non-standard errno: %d\n", errno);
-	return nfserr_io;
-}
-
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfssvc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfssvc.c
@@ -12,6 +12,7 @@
 #include <linux/module.h>
 #include <linux/fs_struct.h>
 #include <linux/swap.h>
+#include <linux/siphash.h>
 
 #include <linux/sunrpc/stats.h>
 #include <linux/sunrpc/svcsock.h>
@@ -33,6 +34,7 @@
 
 #define NFSDDBG_FACILITY	NFSDDBG_SVC
 
+atomic_t			nfsd_th_cnt = ATOMIC_INIT(0);
 extern struct svc_program	nfsd_program;
 static int			nfsd(void *vrqstp);
 #if defined(CONFIG_NFSD_V2_ACL) || defined(CONFIG_NFSD_V3_ACL)
@@ -55,18 +57,17 @@
 						struct svc_process_info *);
 
 /*
- * nfsd_mutex protects nn->nfsd_serv -- both the pointer itself and the members
- * of the svc_serv struct. In particular, ->sv_nrthreads but also to some
- * extent ->sv_temp_socks and ->sv_permsocks. It also protects nfsdstats.th_cnt
+ * nfsd_mutex protects nn->nfsd_serv -- both the pointer itself and some members
+ * of the svc_serv struct such as ->sv_temp_socks and ->sv_permsocks.
  *
  * If (out side the lock) nn->nfsd_serv is non-NULL, then it must point to a
- * properly initialised 'struct svc_serv' with ->sv_nrthreads > 0. That number
- * of nfsd threads must exist and each must listed in ->sp_all_threads in each
- * entry of ->sv_pools[].
+ * properly initialised 'struct svc_serv' with ->sv_nrthreads > 0 (unless
+ * nn->keep_active is set).  That number of nfsd threads must
+ * exist and each must be listed in ->sp_all_threads in some entry of
+ * ->sv_pools[].
  *
- * Transitions of the thread count between zero and non-zero are of particular
- * interest since the svc_serv needs to be created and initialized at that
- * point, or freed.
+ * Each active thread holds a counted reference on nn->nfsd_serv, as does
+ * the nn->keep_active flag and various transient calls to svc_get().
  *
  * Finally, the nfsd_mutex also protects some of the global variables that are
  * accessed when nfsd starts and that are settable via the write_* routines in
@@ -89,10 +90,13 @@
 unsigned long	nfsd_drc_mem_used;
 
 #if defined(CONFIG_NFSD_V2_ACL) || defined(CONFIG_NFSD_V3_ACL)
-static struct svc_stat	nfsd_acl_svcstats;
 static const struct svc_version *nfsd_acl_version[] = {
+# if defined(CONFIG_NFSD_V2_ACL)
 	[2] = &nfsd_acl_version2,
+# endif
+# if defined(CONFIG_NFSD_V3_ACL)
 	[3] = &nfsd_acl_version3,
+# endif
 };
 
 #define NFSD_ACL_MINVERS            2
@@ -104,22 +108,18 @@
 	.pg_vers		= nfsd_acl_version,
 	.pg_name		= "nfsacl",
 	.pg_class		= "nfsd",
-	.pg_stats		= &nfsd_acl_svcstats,
 	.pg_authenticate	= &svc_set_client,
 	.pg_init_request	= nfsd_acl_init_request,
 	.pg_rpcbind_set		= nfsd_acl_rpcbind_set,
 };
 
-static struct svc_stat	nfsd_acl_svcstats = {
-	.program	= &nfsd_acl_program,
-};
 #endif /* defined(CONFIG_NFSD_V2_ACL) || defined(CONFIG_NFSD_V3_ACL) */
 
 static const struct svc_version *nfsd_version[] = {
+#if defined(CONFIG_NFSD_V2)
 	[2] = &nfsd_version2,
-#if defined(CONFIG_NFSD_V3)
-	[3] = &nfsd_version3,
 #endif
+	[3] = &nfsd_version3,
 #if defined(CONFIG_NFSD_V4)
 	[4] = &nfsd_version4,
 #endif
@@ -137,7 +137,6 @@
 	.pg_vers		= nfsd_version,		/* version table */
 	.pg_name		= "nfsd",		/* program name */
 	.pg_class		= "nfsd",		/* authentication class */
-	.pg_stats		= &nfsd_svcstats,	/* version table */
 	.pg_authenticate	= &svc_set_client,	/* export authentication */
 	.pg_init_request	= nfsd_init_request,
 	.pg_rpcbind_set		= nfsd_rpcbind_set,
@@ -293,13 +292,13 @@
 	if (!list_empty(&nn->nfsd_serv->sv_permsocks))
 		return 0;
 
-	error = svc_create_xprt(nn->nfsd_serv, "udp", net, PF_INET, NFS_PORT,
-					SVC_SOCK_DEFAULTS, cred);
+	error = svc_xprt_create(nn->nfsd_serv, "udp", net, PF_INET, NFS_PORT,
+				SVC_SOCK_DEFAULTS, cred);
 	if (error < 0)
 		return error;
 
-	error = svc_create_xprt(nn->nfsd_serv, "tcp", net, PF_INET, NFS_PORT,
-					SVC_SOCK_DEFAULTS, cred);
+	error = svc_xprt_create(nn->nfsd_serv, "tcp", net, PF_INET, NFS_PORT,
+				SVC_SOCK_DEFAULTS, cred);
 	if (error < 0)
 		return error;
 
@@ -345,33 +344,57 @@
 	return nfsd_vers(nn, 2, NFSD_TEST) || nfsd_vers(nn, 3, NFSD_TEST);
 }
 
-void nfsd_copy_boot_verifier(__be32 verf[2], struct nfsd_net *nn)
+/**
+ * nfsd_copy_write_verifier - Atomically copy a write verifier
+ * @verf: buffer in which to receive the verifier cookie
+ * @nn: NFS net namespace
+ *
+ * This function provides a wait-free mechanism for copying the
+ * namespace's write verifier without tearing it.
+ */
+void nfsd_copy_write_verifier(__be32 verf[2], struct nfsd_net *nn)
 {
 	int seq = 0;
 
 	do {
-		read_seqbegin_or_lock(&nn->boot_lock, &seq);
-		/*
-		 * This is opaque to client, so no need to byte-swap. Use
-		 * __force to keep sparse happy. y2038 time_t overflow is
-		 * irrelevant in this usage
-		 */
-		verf[0] = (__force __be32)nn->nfssvc_boot.tv_sec;
-		verf[1] = (__force __be32)nn->nfssvc_boot.tv_nsec;
-	} while (need_seqretry(&nn->boot_lock, seq));
-	done_seqretry(&nn->boot_lock, seq);
+		read_seqbegin_or_lock(&nn->writeverf_lock, &seq);
+		memcpy(verf, nn->writeverf, sizeof(nn->writeverf));
+	} while (need_seqretry(&nn->writeverf_lock, seq));
+	done_seqretry(&nn->writeverf_lock, seq);
 }
 
-static void nfsd_reset_boot_verifier_locked(struct nfsd_net *nn)
+static void nfsd_reset_write_verifier_locked(struct nfsd_net *nn)
 {
-	ktime_get_real_ts64(&nn->nfssvc_boot);
+	struct timespec64 now;
+	u64 verf;
+
+	/*
+	 * Because the time value is hashed, y2038 time_t overflow
+	 * is irrelevant in this usage.
+	 */
+	ktime_get_raw_ts64(&now);
+	verf = siphash_2u64(now.tv_sec, now.tv_nsec, &nn->siphash_key);
+	memcpy(nn->writeverf, &verf, sizeof(nn->writeverf));
 }
 
-void nfsd_reset_boot_verifier(struct nfsd_net *nn)
+/**
+ * nfsd_reset_write_verifier - Generate a new write verifier
+ * @nn: NFS net namespace
+ *
+ * This function updates the ->writeverf field of @nn. This field
+ * contains an opaque cookie that, according to Section 18.32.3 of
+ * RFC 8881, "the client can use to determine whether a server has
+ * changed instance state (e.g., server restart) between a call to
+ * WRITE and a subsequent call to either WRITE or COMMIT.  This
+ * cookie MUST be unchanged during a single instance of the NFSv4.1
+ * server and MUST be unique between instances of the NFSv4.1
+ * server."
+ */
+void nfsd_reset_write_verifier(struct nfsd_net *nn)
 {
-	write_seqlock(&nn->boot_lock);
-	nfsd_reset_boot_verifier_locked(nn);
-	write_sequnlock(&nn->boot_lock);
+	write_seqlock(&nn->writeverf_lock);
+	nfsd_reset_write_verifier_locked(nn);
+	write_sequnlock(&nn->writeverf_lock);
 }
 
 static int nfsd_startup_net(struct net *net, const struct cred *cred)
@@ -399,16 +422,23 @@
 	ret = nfsd_file_cache_start_net(net);
 	if (ret)
 		goto out_lockd;
-	ret = nfs4_state_start_net(net);
+
+	ret = nfsd_reply_cache_init(nn);
 	if (ret)
 		goto out_filecache;
 
+	ret = nfs4_state_start_net(net);
+	if (ret)
+		goto out_reply_cache;
+
 #ifdef CONFIG_NFSD_V4_2_INTER_SSC
 	nfsd4_ssc_init_umount_work(nn);
 #endif
 	nn->nfsd_net_up = true;
 	return 0;
 
+out_reply_cache:
+	nfsd_reply_cache_shutdown(nn);
 out_filecache:
 	nfsd_file_cache_shutdown_net(net);
 out_lockd:
@@ -425,8 +455,9 @@
 {
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 
-	nfsd_file_cache_shutdown_net(net);
 	nfs4_state_shutdown_net(net);
+	nfsd_reply_cache_shutdown(nn);
+	nfsd_file_cache_shutdown_net(net);
 	if (nn->lockd_up) {
 		lockd_down(net);
 		nn->lockd_up = false;
@@ -435,6 +466,7 @@
 	nfsd_shutdown_generic();
 }
 
+static DEFINE_SPINLOCK(nfsd_notifier_lock);
 static int nfsd_inetaddr_event(struct notifier_block *this, unsigned long event,
 	void *ptr)
 {
@@ -444,18 +476,17 @@
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 	struct sockaddr_in sin;
 
-	if ((event != NETDEV_DOWN) ||
-	    !atomic_inc_not_zero(&nn->ntf_refcnt))
+	if (event != NETDEV_DOWN || !nn->nfsd_serv)
 		goto out;
 
+	spin_lock(&nfsd_notifier_lock);
 	if (nn->nfsd_serv) {
 		dprintk("nfsd_inetaddr_event: removed %pI4\n", &ifa->ifa_local);
 		sin.sin_family = AF_INET;
 		sin.sin_addr.s_addr = ifa->ifa_local;
 		svc_age_temp_xprts_now(nn->nfsd_serv, (struct sockaddr *)&sin);
 	}
-	atomic_dec(&nn->ntf_refcnt);
-	wake_up(&nn->ntf_wq);
+	spin_unlock(&nfsd_notifier_lock);
 
 out:
 	return NOTIFY_DONE;
@@ -475,10 +506,10 @@
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 	struct sockaddr_in6 sin6;
 
-	if ((event != NETDEV_DOWN) ||
-	    !atomic_inc_not_zero(&nn->ntf_refcnt))
+	if (event != NETDEV_DOWN || !nn->nfsd_serv)
 		goto out;
 
+	spin_lock(&nfsd_notifier_lock);
 	if (nn->nfsd_serv) {
 		dprintk("nfsd_inet6addr_event: removed %pI6\n", &ifa->addr);
 		sin6.sin6_family = AF_INET6;
@@ -487,8 +518,8 @@
 			sin6.sin6_scope_id = ifa->idev->dev->ifindex;
 		svc_age_temp_xprts_now(nn->nfsd_serv, (struct sockaddr *)&sin6);
 	}
-	atomic_dec(&nn->ntf_refcnt);
-	wake_up(&nn->ntf_wq);
+	spin_unlock(&nfsd_notifier_lock);
+
 out:
 	return NOTIFY_DONE;
 }
@@ -501,11 +532,15 @@
 /* Only used under nfsd_mutex, so this atomic may be overkill: */
 static atomic_t nfsd_notifier_refcount = ATOMIC_INIT(0);
 
-static void nfsd_last_thread(struct svc_serv *serv, struct net *net)
+void nfsd_last_thread(struct net *net)
 {
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
+	struct svc_serv *serv = nn->nfsd_serv;
+
+	spin_lock(&nfsd_notifier_lock);
+	nn->nfsd_serv = NULL;
+	spin_unlock(&nfsd_notifier_lock);
 
-	atomic_dec(&nn->ntf_refcnt);
 	/* check if the notifier still has clients */
 	if (atomic_dec_return(&nfsd_notifier_refcount) == 0) {
 		unregister_inetaddr_notifier(&nfsd_inetaddr_notifier);
@@ -513,7 +548,8 @@
 		unregister_inet6addr_notifier(&nfsd_inet6addr_notifier);
 #endif
 	}
-	wait_event(nn->ntf_wq, atomic_read(&nn->ntf_refcnt) == 0);
+
+	svc_xprt_destroy_all(serv, net);
 
 	/*
 	 * write_ports can create the server without actually starting
@@ -590,24 +626,6 @@
 	return ret;
 }
 
-static const struct svc_serv_ops nfsd_thread_sv_ops = {
-	.svo_shutdown		= nfsd_last_thread,
-	.svo_function		= nfsd,
-	.svo_enqueue_xprt	= svc_xprt_do_enqueue,
-	.svo_setup		= svc_set_num_threads,
-	.svo_module		= THIS_MODULE,
-};
-
-static void nfsd_complete_shutdown(struct net *net)
-{
-	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
-
-	WARN_ON(!mutex_is_locked(&nfsd_mutex));
-
-	nn->nfsd_serv = NULL;
-	complete(&nn->nfsd_shutdown_complete);
-}
-
 void nfsd_shutdown_threads(struct net *net)
 {
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
@@ -622,11 +640,10 @@
 
 	svc_get(serv);
 	/* Kill outstanding nfsd threads */
-	serv->sv_ops->svo_setup(serv, NULL, 0);
-	nfsd_destroy(net);
+	svc_set_num_threads(serv, NULL, 0);
+	nfsd_last_thread(net);
+	svc_put(serv);
 	mutex_unlock(&nfsd_mutex);
-	/* Wait for shutdown of nfsd_serv to complete */
-	wait_for_completion(&nn->nfsd_shutdown_complete);
 }
 
 bool i_am_nfsd(void)
@@ -638,6 +655,7 @@
 {
 	int error;
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
+	struct svc_serv *serv;
 
 	WARN_ON(!mutex_is_locked(&nfsd_mutex));
 	if (nn->nfsd_serv) {
@@ -647,19 +665,20 @@
 	if (nfsd_max_blksize == 0)
 		nfsd_max_blksize = nfsd_get_default_max_blksize();
 	nfsd_reset_versions(nn);
-	nn->nfsd_serv = svc_create_pooled(&nfsd_program, nfsd_max_blksize,
-						&nfsd_thread_sv_ops);
-	if (nn->nfsd_serv == NULL)
+	serv = svc_create_pooled(&nfsd_program, &nn->nfsd_svcstats,
+				 nfsd_max_blksize, nfsd);
+	if (serv == NULL)
 		return -ENOMEM;
-	init_completion(&nn->nfsd_shutdown_complete);
 
-	nn->nfsd_serv->sv_maxconn = nn->max_connections;
-	error = svc_bind(nn->nfsd_serv, net);
+	serv->sv_maxconn = nn->max_connections;
+	error = svc_bind(serv, net);
 	if (error < 0) {
-		svc_destroy(nn->nfsd_serv);
-		nfsd_complete_shutdown(net);
+		svc_put(serv);
 		return error;
 	}
+	spin_lock(&nfsd_notifier_lock);
+	nn->nfsd_serv = serv;
+	spin_unlock(&nfsd_notifier_lock);
 
 	set_max_drc();
 	/* check if the notifier is already set */
@@ -669,8 +688,7 @@
 		register_inet6addr_notifier(&nfsd_inet6addr_notifier);
 #endif
 	}
-	atomic_inc(&nn->ntf_refcnt);
-	nfsd_reset_boot_verifier(nn);
+	nfsd_reset_write_verifier(nn);
 	return 0;
 }
 
@@ -697,18 +715,6 @@
 	return 0;
 }
 
-void nfsd_destroy(struct net *net)
-{
-	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
-	int destroy = (nn->nfsd_serv->sv_nrthreads == 1);
-
-	if (destroy)
-		svc_shutdown_net(nn->nfsd_serv, net);
-	svc_destroy(nn->nfsd_serv);
-	if (destroy)
-		nfsd_complete_shutdown(net);
-}
-
 int nfsd_set_nrthreads(int n, int *nthreads, struct net *net)
 {
 	int i = 0;
@@ -733,7 +739,7 @@
 	if (tot > NFSD_MAXSERVS) {
 		/* total too large: scale down requested numbers */
 		for (i = 0; i < n && tot > 0; i++) {
-		    	int new = nthreads[i] * NFSD_MAXSERVS / tot;
+			int new = nthreads[i] * NFSD_MAXSERVS / tot;
 			tot -= (nthreads[i] - new);
 			nthreads[i] = new;
 		}
@@ -753,12 +759,13 @@
 	/* apply the new numbers */
 	svc_get(nn->nfsd_serv);
 	for (i = 0; i < n; i++) {
-		err = nn->nfsd_serv->sv_ops->svo_setup(nn->nfsd_serv,
-				&nn->nfsd_serv->sv_pools[i], nthreads[i]);
+		err = svc_set_num_threads(nn->nfsd_serv,
+					  &nn->nfsd_serv->sv_pools[i],
+					  nthreads[i]);
 		if (err)
 			break;
 	}
-	nfsd_destroy(net);
+	svc_put(nn->nfsd_serv);
 	return err;
 }
 
@@ -773,6 +780,7 @@
 	int	error;
 	bool	nfsd_up_before;
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
+	struct svc_serv *serv;
 
 	mutex_lock(&nfsd_mutex);
 	dprintk("nfsd: creating service\n");
@@ -784,7 +792,7 @@
 	if (nrservs == 0 && nn->nfsd_serv == NULL)
 		goto out;
 
-	strlcpy(nn->nfsd_name, utsname()->nodename,
+	strscpy(nn->nfsd_name, utsname()->nodename,
 		sizeof(nn->nfsd_name));
 
 	error = nfsd_create_serv(net);
@@ -792,24 +800,25 @@
 		goto out;
 
 	nfsd_up_before = nn->nfsd_net_up;
+	serv = nn->nfsd_serv;
 
 	error = nfsd_startup_net(net, cred);
 	if (error)
-		goto out_destroy;
-	error = nn->nfsd_serv->sv_ops->svo_setup(nn->nfsd_serv,
-			NULL, nrservs);
+		goto out_put;
+	error = svc_set_num_threads(serv, NULL, nrservs);
 	if (error)
 		goto out_shutdown;
-	/* We are holding a reference to nn->nfsd_serv which
-	 * we don't want to count in the return value,
-	 * so subtract 1
-	 */
-	error = nn->nfsd_serv->sv_nrthreads - 1;
+	error = serv->sv_nrthreads;
+	if (error == 0)
+		nfsd_last_thread(net);
 out_shutdown:
 	if (error < 0 && !nfsd_up_before)
 		nfsd_shutdown_net(net);
-out_destroy:
-	nfsd_destroy(net);		/* Release server */
+out_put:
+	/* Threads now hold service active */
+	if (xchg(&nn->keep_active, 0))
+		svc_put(serv);
+	svc_put(serv);
 out:
 	mutex_unlock(&nfsd_mutex);
 	return error;
@@ -923,9 +932,6 @@
 	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 	int err;
 
-	/* Lock module and set up kernel thread */
-	mutex_lock(&nfsd_mutex);
-
 	/* At this point, the thread shares current->fs
 	 * with the init process. We need to create files with the
 	 * umask as defined by the client instead of init's umask. */
@@ -936,17 +942,7 @@
 
 	current->fs->umask = 0;
 
-	/*
-	 * thread is spawned with all signals set to SIG_IGN, re-enable
-	 * the ones that will bring down the thread
-	 */
-	allow_signal(SIGKILL);
-	allow_signal(SIGHUP);
-	allow_signal(SIGINT);
-	allow_signal(SIGQUIT);
-
-	nfsdstats.th_cnt++;
-	mutex_unlock(&nfsd_mutex);
+	atomic_inc(&nfsd_th_cnt);
 
 	set_freezable();
 
@@ -970,23 +966,11 @@
 		validate_process_creds();
 	}
 
-	/* Clear signals before calling svc_exit_thread() */
-	flush_signals(current);
-
-	mutex_lock(&nfsd_mutex);
-	nfsdstats.th_cnt --;
+	atomic_dec(&nfsd_th_cnt);
 
 out:
-	rqstp->rq_server = NULL;
-
 	/* Release the thread */
 	svc_exit_thread(rqstp);
-
-	nfsd_destroy(net);
-
-	/* Release module */
-	mutex_unlock(&nfsd_mutex);
-	module_put_and_exit(0);
 	return 0;
 }
 
@@ -1004,9 +988,6 @@
 int nfsd_dispatch(struct svc_rqst *rqstp, __be32 *statp)
 {
 	const struct svc_procedure *proc = rqstp->rq_procinfo;
-	struct kvec *argv = &rqstp->rq_arg.head[0];
-	struct kvec *resv = &rqstp->rq_res.head[0];
-	__be32 *p;
 
 	/*
 	 * Give the xdr decoder a chance to change this if it wants
@@ -1015,7 +996,7 @@
 	rqstp->rq_cachetype = proc->pc_cachetype;
 
 	svcxdr_init_decode(rqstp);
-	if (!proc->pc_decode(rqstp, argv->iov_base))
+	if (!proc->pc_decode(rqstp, &rqstp->rq_arg_stream))
 		goto out_decode_err;
 
 	switch (nfsd_cache_lookup(rqstp)) {
@@ -1031,14 +1012,13 @@
 	 * Need to grab the location to store the status, as
 	 * NFSv4 does some encoding while processing
 	 */
-	p = resv->iov_base + resv->iov_len;
 	svcxdr_init_encode(rqstp);
 
 	*statp = proc->pc_func(rqstp);
-	if (*statp == rpc_drop_reply || test_bit(RQ_DROPME, &rqstp->rq_flags))
+	if (test_bit(RQ_DROPME, &rqstp->rq_flags))
 		goto out_update_drop;
 
-	if (!proc->pc_encode(rqstp, p))
+	if (!proc->pc_encode(rqstp, &rqstp->rq_res_stream))
 		goto out_encode_err;
 
 	nfsd_cache_update(rqstp, rqstp->rq_cachetype, statp + 1);
@@ -1065,29 +1045,29 @@
 /**
  * nfssvc_decode_voidarg - Decode void arguments
  * @rqstp: Server RPC transaction context
- * @p: buffer containing arguments to decode
+ * @xdr: XDR stream positioned at arguments to decode
  *
  * Return values:
- *   %0: Arguments were not valid
- *   %1: Decoding was successful
+ *   %false: Arguments were not valid
+ *   %true: Decoding was successful
  */
-int nfssvc_decode_voidarg(struct svc_rqst *rqstp, __be32 *p)
+bool nfssvc_decode_voidarg(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return 1;
+	return true;
 }
 
 /**
  * nfssvc_encode_voidres - Encode void results
  * @rqstp: Server RPC transaction context
- * @p: buffer in which to encode results
+ * @xdr: XDR stream into which to encode results
  *
  * Return values:
- *   %0: Local error while encoding
- *   %1: Encoding was successful
+ *   %false: Local error while encoding
+ *   %true: Encoding was successful
  */
-int nfssvc_encode_voidres(struct svc_rqst *rqstp, __be32 *p)
+bool nfssvc_encode_voidres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	return 1;
+	return true;
 }
 
 int nfsd_pool_stats_open(struct inode *inode, struct file *file)
@@ -1100,7 +1080,6 @@
 		mutex_unlock(&nfsd_mutex);
 		return -ENODEV;
 	}
-	/* bump up the psudo refcount while traversing */
 	svc_get(nn->nfsd_serv);
 	ret = svc_pool_stats_open(nn->nfsd_serv, file);
 	mutex_unlock(&nfsd_mutex);
@@ -1109,12 +1088,12 @@
 
 int nfsd_pool_stats_release(struct inode *inode, struct file *file)
 {
+	struct seq_file *seq = file->private_data;
+	struct svc_serv *serv = seq->private;
 	int ret = seq_release(inode, file);
-	struct net *net = inode->i_sb->s_fs_info;
 
 	mutex_lock(&nfsd_mutex);
-	/* this function really, really should have been called svc_put() */
-	nfsd_destroy(net);
+	svc_put(serv);
 	mutex_unlock(&nfsd_mutex);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/nfsxdr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/nfsxdr.c
@@ -64,7 +64,7 @@
 	if (!p)
 		return false;
 	fh_init(fhp, NFS_FHSIZE);
-	memcpy(&fhp->fh_handle.fh_base, p, NFS_FHSIZE);
+	memcpy(&fhp->fh_handle.fh_raw, p, NFS_FHSIZE);
 	fhp->fh_handle.fh_size = NFS_FHSIZE;
 
 	return true;
@@ -78,7 +78,7 @@
 	p = xdr_reserve_space(xdr, NFS_FHSIZE);
 	if (!p)
 		return false;
-	memcpy(p, &fhp->fh_handle.fh_base, NFS_FHSIZE);
+	memcpy(p, &fhp->fh_handle.fh_raw, NFS_FHSIZE);
 
 	return true;
 }
@@ -272,94 +272,79 @@
  * XDR decode functions
  */
 
-int
-nfssvc_decode_fhandleargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_fhandleargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_fhandle *args = rqstp->rq_argp;
 
 	return svcxdr_decode_fhandle(xdr, &args->fh);
 }
 
-int
-nfssvc_decode_sattrargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_sattrargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_sattrargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_fhandle(xdr, &args->fh) &&
 		svcxdr_decode_sattr(rqstp, xdr, &args->attrs);
 }
 
-int
-nfssvc_decode_diropargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_diropargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_diropargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_diropargs(xdr, &args->fh, &args->name, &args->len);
 }
 
-int
-nfssvc_decode_readargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_readargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_readargs *args = rqstp->rq_argp;
 	u32 totalcount;
 
 	if (!svcxdr_decode_fhandle(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->offset) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 	/* totalcount is ignored */
 	if (xdr_stream_decode_u32(xdr, &totalcount) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
-int
-nfssvc_decode_writeargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_writeargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_writeargs *args = rqstp->rq_argp;
-	struct kvec *head = rqstp->rq_arg.head;
-	struct kvec *tail = rqstp->rq_arg.tail;
 	u32 beginoffset, totalcount;
-	size_t remaining;
 
 	if (!svcxdr_decode_fhandle(xdr, &args->fh))
-		return 0;
+		return false;
 	/* beginoffset is ignored */
 	if (xdr_stream_decode_u32(xdr, &beginoffset) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->offset) < 0)
-		return 0;
+		return false;
 	/* totalcount is ignored */
 	if (xdr_stream_decode_u32(xdr, &totalcount) < 0)
-		return 0;
+		return false;
 
 	/* opaque data */
 	if (xdr_stream_decode_u32(xdr, &args->len) < 0)
-		return 0;
+		return false;
 	if (args->len > NFSSVC_MAXBLKSIZE_V2)
-		return 0;
-	remaining = head->iov_len + rqstp->rq_arg.page_len + tail->iov_len;
-	remaining -= xdr_stream_pos(xdr);
-	if (remaining < xdr_align_size(args->len))
-		return 0;
-	args->first.iov_base = xdr->p;
-	args->first.iov_len = head->iov_len - xdr_stream_pos(xdr);
+		return false;
 
-	return 1;
+	return xdr_stream_subsegment(xdr, &args->payload, args->len);
 }
 
-int
-nfssvc_decode_createargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_createargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_createargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_diropargs(xdr, &args->fh,
@@ -367,10 +352,9 @@
 		svcxdr_decode_sattr(rqstp, xdr, &args->attrs);
 }
 
-int
-nfssvc_decode_renameargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_renameargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_renameargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_diropargs(xdr, &args->ffh,
@@ -379,10 +363,9 @@
 					&args->tname, &args->tlen);
 }
 
-int
-nfssvc_decode_linkargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_linkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_linkargs *args = rqstp->rq_argp;
 
 	return svcxdr_decode_fhandle(xdr, &args->ffh) &&
@@ -390,178 +373,170 @@
 					&args->tname, &args->tlen);
 }
 
-int
-nfssvc_decode_symlinkargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_symlinkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_symlinkargs *args = rqstp->rq_argp;
 	struct kvec *head = rqstp->rq_arg.head;
 
 	if (!svcxdr_decode_diropargs(xdr, &args->ffh, &args->fname, &args->flen))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->tlen) < 0)
-		return 0;
+		return false;
 	if (args->tlen == 0)
-		return 0;
+		return false;
 
 	args->first.iov_len = head->iov_len - xdr_stream_pos(xdr);
 	args->first.iov_base = xdr_inline_decode(xdr, args->tlen);
 	if (!args->first.iov_base)
-		return 0;
+		return false;
 	return svcxdr_decode_sattr(rqstp, xdr, &args->attrs);
 }
 
-int
-nfssvc_decode_readdirargs(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_decode_readdirargs(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
 	struct nfsd_readdirargs *args = rqstp->rq_argp;
 
 	if (!svcxdr_decode_fhandle(xdr, &args->fh))
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->cookie) < 0)
-		return 0;
+		return false;
 	if (xdr_stream_decode_u32(xdr, &args->count) < 0)
-		return 0;
+		return false;
 
-	return 1;
+	return true;
 }
 
 /*
  * XDR encode functions
  */
 
-int
-nfssvc_encode_statres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_statres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_stat *resp = rqstp->rq_resp;
 
 	return svcxdr_encode_stat(xdr, resp->status);
 }
 
-int
-nfssvc_encode_attrstatres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_attrstatres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_attrstat *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_fattr(rqstp, xdr, &resp->fh, &resp->stat))
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
-int
-nfssvc_encode_diropres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_diropres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_diropres *resp = rqstp->rq_resp;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_fhandle(xdr, &resp->fh))
-			return 0;
+			return false;
 		if (!svcxdr_encode_fattr(rqstp, xdr, &resp->fh, &resp->stat))
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
-int
-nfssvc_encode_readlinkres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_readlinkres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_readlinkres *resp = rqstp->rq_resp;
 	struct kvec *head = rqstp->rq_res.head;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (xdr_stream_encode_u32(xdr, resp->len) < 0)
-			return 0;
+			return false;
 		xdr_write_pages(xdr, &resp->page, 0, resp->len);
 		if (svc_encode_result_payload(rqstp, head->iov_len, resp->len) < 0)
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
-int
-nfssvc_encode_readres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_readres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_readres *resp = rqstp->rq_resp;
 	struct kvec *head = rqstp->rq_res.head;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		if (!svcxdr_encode_fattr(rqstp, xdr, &resp->fh, &resp->stat))
-			return 0;
+			return false;
 		if (xdr_stream_encode_u32(xdr, resp->count) < 0)
-			return 0;
+			return false;
 		xdr_write_pages(xdr, resp->pages, rqstp->rq_res.page_base,
 				resp->count);
 		if (svc_encode_result_payload(rqstp, head->iov_len, resp->count) < 0)
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
-int
-nfssvc_encode_readdirres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_readdirres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_readdirres *resp = rqstp->rq_resp;
 	struct xdr_buf *dirlist = &resp->dirlist;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		xdr_write_pages(xdr, dirlist->pages, 0, dirlist->len);
 		/* no more entries */
 		if (xdr_stream_encode_item_absent(xdr) < 0)
-			return 0;
+			return false;
 		if (xdr_stream_encode_bool(xdr, resp->common.err == nfserr_eof) < 0)
-			return 0;
+			return false;
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
-int
-nfssvc_encode_statfsres(struct svc_rqst *rqstp, __be32 *p)
+bool
+nfssvc_encode_statfsres(struct svc_rqst *rqstp, struct xdr_stream *xdr)
 {
-	struct xdr_stream *xdr = &rqstp->rq_res_stream;
 	struct nfsd_statfsres *resp = rqstp->rq_resp;
 	struct kstatfs	*stat = &resp->stats;
+	__be32 *p;
 
 	if (!svcxdr_encode_stat(xdr, resp->status))
-		return 0;
+		return false;
 	switch (resp->status) {
 	case nfs_ok:
 		p = xdr_reserve_space(xdr, XDR_UNIT * 5);
 		if (!p)
-			return 0;
+			return false;
 		*p++ = cpu_to_be32(NFSSVC_MAXBLKSIZE_V2);
 		*p++ = cpu_to_be32(stat->f_bsize);
 		*p++ = cpu_to_be32(stat->f_blocks);
@@ -570,7 +545,7 @@
 		break;
 	}
 
-	return 1;
+	return true;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/state.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/state.h
@@ -57,11 +57,11 @@
 } stateid_t;
 
 typedef struct {
-	stateid_t		stid;
+	stateid_t		cs_stid;
 #define NFS4_COPY_STID 1
 #define NFS4_COPYNOTIFY_STID 2
-	unsigned char		sc_type;
-	refcount_t		sc_count;
+	unsigned char		cs_type;
+	refcount_t		cs_count;
 } copy_stateid_t;
 
 struct nfsd4_callback {
@@ -149,6 +149,7 @@
 /* For recall: */
 	int			dl_retries;
 	struct nfsd4_callback	dl_recall;
+	bool			dl_recalled;
 };
 
 #define cb_to_delegation(cb) \
@@ -174,7 +175,7 @@
 /* Maximum number of slots per session. 160 is useful for long haul TCP */
 #define NFSD_MAX_SLOTS_PER_SESSION     160
 /* Maximum number of operations per session compound */
-#define NFSD_MAX_OPS_PER_COMPOUND	16
+#define NFSD_MAX_OPS_PER_COMPOUND	50
 /* Maximum  session per slot cache size */
 #define NFSD_SLOT_CACHE_SIZE		2048
 /* Maximum number of NFSD_SLOT_CACHE_SIZE slots per session */
@@ -283,6 +284,28 @@
 #define HEXDIR_LEN     33 /* hex version of 16 byte md5 of cl_name plus '\0' */
 
 /*
+ *       State                Meaning                  Where set
+ * --------------------------------------------------------------------------
+ * | NFSD4_ACTIVE      | Confirmed, active    | Default                     |
+ * |------------------- ----------------------------------------------------|
+ * | NFSD4_COURTESY    | Courtesy state.      | nfs4_get_client_reaplist    |
+ * |                   | Lease/lock/share     |                             |
+ * |                   | reservation conflict |                             |
+ * |                   | can cause Courtesy   |                             |
+ * |                   | client to be expired |                             |
+ * |------------------------------------------------------------------------|
+ * | NFSD4_EXPIRABLE   | Courtesy client to be| nfs4_laundromat             |
+ * |                   | expired by Laundromat| try_to_expire_client        |
+ * |                   | due to conflict      |                             |
+ * |------------------------------------------------------------------------|
+ */
+enum {
+	NFSD4_ACTIVE = 0,
+	NFSD4_COURTESY,
+	NFSD4_EXPIRABLE,
+};
+
+/*
  * struct nfs4_client - one per client.  Clientids live here.
  *
  * The initial object created by an NFS client using SETCLIENTID (for NFSv4.0)
@@ -345,6 +368,7 @@
 #define NFSD4_CLIENT_UPCALL_LOCK	(5)	/* upcall serialization */
 #define NFSD4_CLIENT_CB_FLAG_MASK	(1 << NFSD4_CLIENT_CB_UPDATE | \
 					 1 << NFSD4_CLIENT_CB_KILL)
+#define NFSD4_CLIENT_CB_RECALL_ANY	(6)
 	unsigned long		cl_flags;
 	const struct cred	*cl_cb_cred;
 	struct rpc_clnt		*cl_cb_client;
@@ -385,6 +409,13 @@
 	struct list_head	async_copies;	/* list of async copies */
 	spinlock_t		async_lock;	/* lock for async copies */
 	atomic_t		cl_cb_inflight;	/* Outstanding callbacks */
+
+	unsigned int		cl_state;
+	atomic_t		cl_delegs_in_recall;
+
+	struct nfsd4_cb_recall_any	*cl_ra;
+	time64_t		cl_ra_time;
+	struct list_head	cl_ra_cblist;
 };
 
 /* struct nfs4_client_reset
@@ -510,16 +541,13 @@
  * inode can have multiple filehandles associated with it, so there is
  * (potentially) a many to one relationship between this struct and struct
  * inode.
- *
- * These are hashed by filehandle in the file_hashtbl, which is protected by
- * the global state_lock spinlock.
  */
 struct nfs4_file {
 	refcount_t		fi_ref;
 	struct inode *		fi_inode;
 	bool			fi_aliased;
 	spinlock_t		fi_lock;
-	struct hlist_node       fi_hash;	/* hash on fi_fhandle */
+	struct rhlist_head	fi_rlist;
 	struct list_head        fi_stateids;
 	union {
 		struct list_head	fi_delegations;
@@ -568,6 +596,10 @@
 	struct list_head		st_locks;
 	struct nfs4_stateowner		*st_stateowner;
 	struct nfs4_clnt_odstate	*st_clnt_odstate;
+/*
+ * These bitmasks use 3 separate bits for READ, ALLOW, and BOTH; see the
+ * comment above bmap_to_share_mode() for explanation:
+ */
 	unsigned char			st_access_bmap;
 	unsigned char			st_deny_bmap;
 	struct nfs4_ol_stateid		*st_openstp;
@@ -609,6 +641,7 @@
 	NFSPROC4_CLNT_CB_OFFLOAD,
 	NFSPROC4_CLNT_CB_SEQUENCE,
 	NFSPROC4_CLNT_CB_NOTIFY_LOCK,
+	NFSPROC4_CLNT_CB_RECALL_ANY,
 };
 
 /* Returns true iff a is later than b: */
@@ -629,6 +662,7 @@
 	struct file_lock	nbl_lock;
 	struct knfsd_fh		nbl_fh;
 	struct nfsd4_callback	nbl_cb;
+	struct kref		nbl_kref;
 };
 
 struct nfsd4_compound_state;
@@ -661,18 +695,16 @@
 extern void nfsd4_change_callback(struct nfs4_client *clp, struct nfs4_cb_conn *);
 extern void nfsd4_init_cb(struct nfsd4_callback *cb, struct nfs4_client *clp,
 		const struct nfsd4_callback_ops *ops, enum nfsd4_cb_op op);
-extern void nfsd4_run_cb(struct nfsd4_callback *cb);
+extern bool nfsd4_run_cb(struct nfsd4_callback *cb);
 extern int nfsd4_create_callback_queue(void);
 extern void nfsd4_destroy_callback_queue(void);
 extern void nfsd4_shutdown_callback(struct nfs4_client *);
 extern void nfsd4_shutdown_copy(struct nfs4_client *clp);
-extern void nfsd4_prepare_cb_recall(struct nfs4_delegation *dp);
 extern struct nfs4_client_reclaim *nfs4_client_to_reclaim(struct xdr_netobj name,
 				struct xdr_netobj princhash, struct nfsd_net *nn);
 extern bool nfs4_has_reclaimed_state(struct xdr_netobj name, struct nfsd_net *nn);
 
 void put_nfs4_file(struct nfs4_file *fi);
-extern void nfs4_put_copy(struct nfsd4_copy *copy);
 extern struct nfsd4_copy *
 find_async_copy(struct nfs4_client *clp, stateid_t *staetid);
 extern void nfs4_put_cpntf_state(struct nfsd_net *nn,
@@ -697,4 +729,9 @@
 extern int nfsd4_client_record_check(struct nfs4_client *clp);
 extern void nfsd4_record_grace_done(struct nfsd_net *nn);
 
+static inline bool try_to_expire_client(struct nfs4_client *clp)
+{
+	cmpxchg(&clp->cl_state, NFSD4_COURTESY, NFSD4_EXPIRABLE);
+	return clp->cl_state == NFSD4_EXPIRABLE;
+}
 #endif   /* NFSD4_STATE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/stats.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/stats.c
@@ -27,25 +27,22 @@
 
 #include "nfsd.h"
 
-struct nfsd_stats	nfsdstats;
-struct svc_stat		nfsd_svcstats = {
-	.program	= &nfsd_program,
-};
-
-static int nfsd_proc_show(struct seq_file *seq, void *v)
+static int nfsd_show(struct seq_file *seq, void *v)
 {
+	struct net *net = PDE_DATA(file_inode(seq->file));
+	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 	int i;
 
 	seq_printf(seq, "rc %lld %lld %lld\nfh %lld 0 0 0 0\nio %lld %lld\n",
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_RC_HITS]),
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_RC_MISSES]),
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_RC_NOCACHE]),
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_FH_STALE]),
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_IO_READ]),
-		   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_IO_WRITE]));
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_RC_HITS]),
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_RC_MISSES]),
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_RC_NOCACHE]),
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_FH_STALE]),
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_IO_READ]),
+		   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_IO_WRITE]));
 
 	/* thread usage: */
-	seq_printf(seq, "th %u 0", nfsdstats.th_cnt);
+	seq_printf(seq, "th %u 0", atomic_read(&nfsd_th_cnt));
 
 	/* deprecated thread usage histogram stats */
 	for (i = 0; i < 10; i++)
@@ -55,7 +52,7 @@
 	seq_puts(seq, "\nra 0 0 0 0 0 0 0 0 0 0 0 0\n");
 
 	/* show my rpc info */
-	svc_seq_show(seq, &nfsd_svcstats);
+	svc_seq_show(seq, &nn->nfsd_svcstats);
 
 #ifdef CONFIG_NFSD_V4
 	/* Show count for individual nfsv4 operations */
@@ -63,7 +60,7 @@
 	seq_printf(seq,"proc4ops %u", LAST_NFS4_OP + 1);
 	for (i = 0; i <= LAST_NFS4_OP; i++) {
 		seq_printf(seq, " %lld",
-			   percpu_counter_sum_positive(&nfsdstats.counter[NFSD_STATS_NFS4_OP(i)]));
+			   percpu_counter_sum_positive(&nn->counter[NFSD_STATS_NFS4_OP(i)]));
 	}
 
 	seq_putc(seq, '\n');
@@ -72,19 +69,9 @@
 	return 0;
 }
 
-static int nfsd_proc_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, nfsd_proc_show, NULL);
-}
-
-static const struct proc_ops nfsd_proc_ops = {
-	.proc_open	= nfsd_proc_open,
-	.proc_read	= seq_read,
-	.proc_lseek	= seq_lseek,
-	.proc_release	= single_release,
-};
+DEFINE_PROC_SHOW_ATTRIBUTE(nfsd);
 
-int nfsd_percpu_counters_init(struct percpu_counter counters[], int num)
+int nfsd_percpu_counters_init(struct percpu_counter *counters, int num)
 {
 	int i, err = 0;
 
@@ -116,31 +103,24 @@
 		percpu_counter_destroy(&counters[i]);
 }
 
-static int nfsd_stat_counters_init(void)
+int nfsd_stat_counters_init(struct nfsd_net *nn)
 {
-	return nfsd_percpu_counters_init(nfsdstats.counter, NFSD_STATS_COUNTERS_NUM);
+	return nfsd_percpu_counters_init(nn->counter, NFSD_STATS_COUNTERS_NUM);
 }
 
-static void nfsd_stat_counters_destroy(void)
+void nfsd_stat_counters_destroy(struct nfsd_net *nn)
 {
-	nfsd_percpu_counters_destroy(nfsdstats.counter, NFSD_STATS_COUNTERS_NUM);
+	nfsd_percpu_counters_destroy(nn->counter, NFSD_STATS_COUNTERS_NUM);
 }
 
-int nfsd_stat_init(void)
+void nfsd_proc_stat_init(struct net *net)
 {
-	int err;
+	struct nfsd_net *nn = net_generic(net, nfsd_net_id);
 
-	err = nfsd_stat_counters_init();
-	if (err)
-		return err;
-
-	svc_proc_register(&init_net, &nfsd_svcstats, &nfsd_proc_ops);
-
-	return 0;
+	svc_proc_register(net, &nn->nfsd_svcstats, &nfsd_proc_ops);
 }
 
-void nfsd_stat_shutdown(void)
+void nfsd_proc_stat_shutdown(struct net *net)
 {
-	nfsd_stat_counters_destroy();
-	svc_proc_unregister(&init_net, "nfsd");
+	svc_proc_unregister(net, "nfsd");
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/stats.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/stats.h
@@ -10,89 +10,66 @@
 #include <uapi/linux/nfsd/stats.h>
 #include <linux/percpu_counter.h>
 
+int nfsd_percpu_counters_init(struct percpu_counter *counters, int num);
+void nfsd_percpu_counters_reset(struct percpu_counter *counters, int num);
+void nfsd_percpu_counters_destroy(struct percpu_counter *counters, int num);
+int nfsd_stat_counters_init(struct nfsd_net *nn);
+void nfsd_stat_counters_destroy(struct nfsd_net *nn);
+void nfsd_proc_stat_init(struct net *net);
+void nfsd_proc_stat_shutdown(struct net *net);
 
-enum {
-	NFSD_STATS_RC_HITS,		/* repcache hits */
-	NFSD_STATS_RC_MISSES,		/* repcache misses */
-	NFSD_STATS_RC_NOCACHE,		/* uncached reqs */
-	NFSD_STATS_FH_STALE,		/* FH stale error */
-	NFSD_STATS_IO_READ,		/* bytes returned to read requests */
-	NFSD_STATS_IO_WRITE,		/* bytes passed in write requests */
-#ifdef CONFIG_NFSD_V4
-	NFSD_STATS_FIRST_NFS4_OP,	/* count of individual nfsv4 operations */
-	NFSD_STATS_LAST_NFS4_OP = NFSD_STATS_FIRST_NFS4_OP + LAST_NFS4_OP,
-#define NFSD_STATS_NFS4_OP(op)	(NFSD_STATS_FIRST_NFS4_OP + (op))
-#endif
-	NFSD_STATS_COUNTERS_NUM
-};
-
-struct nfsd_stats {
-	struct percpu_counter	counter[NFSD_STATS_COUNTERS_NUM];
-
-	/* Protected by nfsd_mutex */
-	unsigned int	th_cnt;		/* number of available threads */
-};
-
-
-extern struct nfsd_stats	nfsdstats;
-
-extern struct svc_stat		nfsd_svcstats;
-
-int nfsd_percpu_counters_init(struct percpu_counter counters[], int num);
-void nfsd_percpu_counters_reset(struct percpu_counter counters[], int num);
-void nfsd_percpu_counters_destroy(struct percpu_counter counters[], int num);
-int nfsd_stat_init(void);
-void nfsd_stat_shutdown(void);
-
-static inline void nfsd_stats_rc_hits_inc(void)
+static inline void nfsd_stats_rc_hits_inc(struct nfsd_net *nn)
 {
-	percpu_counter_inc(&nfsdstats.counter[NFSD_STATS_RC_HITS]);
+	percpu_counter_inc(&nn->counter[NFSD_STATS_RC_HITS]);
 }
 
-static inline void nfsd_stats_rc_misses_inc(void)
+static inline void nfsd_stats_rc_misses_inc(struct nfsd_net *nn)
 {
-	percpu_counter_inc(&nfsdstats.counter[NFSD_STATS_RC_MISSES]);
+	percpu_counter_inc(&nn->counter[NFSD_STATS_RC_MISSES]);
 }
 
-static inline void nfsd_stats_rc_nocache_inc(void)
+static inline void nfsd_stats_rc_nocache_inc(struct nfsd_net *nn)
 {
-	percpu_counter_inc(&nfsdstats.counter[NFSD_STATS_RC_NOCACHE]);
+	percpu_counter_inc(&nn->counter[NFSD_STATS_RC_NOCACHE]);
 }
 
-static inline void nfsd_stats_fh_stale_inc(struct svc_export *exp)
+static inline void nfsd_stats_fh_stale_inc(struct nfsd_net *nn,
+					   struct svc_export *exp)
 {
-	percpu_counter_inc(&nfsdstats.counter[NFSD_STATS_FH_STALE]);
-	if (exp)
-		percpu_counter_inc(&exp->ex_stats.counter[EXP_STATS_FH_STALE]);
+	percpu_counter_inc(&nn->counter[NFSD_STATS_FH_STALE]);
+	if (exp && exp->ex_stats)
+		percpu_counter_inc(&exp->ex_stats->counter[EXP_STATS_FH_STALE]);
 }
 
-static inline void nfsd_stats_io_read_add(struct svc_export *exp, s64 amount)
+static inline void nfsd_stats_io_read_add(struct nfsd_net *nn,
+					  struct svc_export *exp, s64 amount)
 {
-	percpu_counter_add(&nfsdstats.counter[NFSD_STATS_IO_READ], amount);
-	if (exp)
-		percpu_counter_add(&exp->ex_stats.counter[EXP_STATS_IO_READ], amount);
+	percpu_counter_add(&nn->counter[NFSD_STATS_IO_READ], amount);
+	if (exp && exp->ex_stats)
+		percpu_counter_add(&exp->ex_stats->counter[EXP_STATS_IO_READ], amount);
 }
 
-static inline void nfsd_stats_io_write_add(struct svc_export *exp, s64 amount)
+static inline void nfsd_stats_io_write_add(struct nfsd_net *nn,
+					   struct svc_export *exp, s64 amount)
 {
-	percpu_counter_add(&nfsdstats.counter[NFSD_STATS_IO_WRITE], amount);
-	if (exp)
-		percpu_counter_add(&exp->ex_stats.counter[EXP_STATS_IO_WRITE], amount);
+	percpu_counter_add(&nn->counter[NFSD_STATS_IO_WRITE], amount);
+	if (exp && exp->ex_stats)
+		percpu_counter_add(&exp->ex_stats->counter[EXP_STATS_IO_WRITE], amount);
 }
 
 static inline void nfsd_stats_payload_misses_inc(struct nfsd_net *nn)
 {
-	percpu_counter_inc(&nn->counter[NFSD_NET_PAYLOAD_MISSES]);
+	percpu_counter_inc(&nn->counter[NFSD_STATS_PAYLOAD_MISSES]);
 }
 
 static inline void nfsd_stats_drc_mem_usage_add(struct nfsd_net *nn, s64 amount)
 {
-	percpu_counter_add(&nn->counter[NFSD_NET_DRC_MEM_USAGE], amount);
+	percpu_counter_add(&nn->counter[NFSD_STATS_DRC_MEM_USAGE], amount);
 }
 
 static inline void nfsd_stats_drc_mem_usage_sub(struct nfsd_net *nn, s64 amount)
 {
-	percpu_counter_sub(&nn->counter[NFSD_NET_DRC_MEM_USAGE], amount);
+	percpu_counter_sub(&nn->counter[NFSD_STATS_DRC_MEM_USAGE], amount);
 }
 
 #endif /* _NFSD_STATS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/trace.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/trace.h
@@ -9,24 +9,12 @@
 #define _NFSD_TRACE_H
 
 #include <linux/tracepoint.h>
+#include <linux/sunrpc/xprt.h>
+#include <trace/misc/nfs.h>
+
 #include "export.h"
 #include "nfsfh.h"
-
-#define NFSD_TRACE_PROC_ARG_FIELDS \
-		__field(unsigned int, netns_ino) \
-		__field(u32, xid) \
-		__array(unsigned char, server, sizeof(struct sockaddr_in6)) \
-		__array(unsigned char, client, sizeof(struct sockaddr_in6))
-
-#define NFSD_TRACE_PROC_ARG_ASSIGNMENTS \
-		do { \
-			__entry->netns_ino = SVC_NET(rqstp)->ns.inum; \
-			__entry->xid = be32_to_cpu(rqstp->rq_xid); \
-			memcpy(__entry->server, &rqstp->rq_xprt->xpt_local, \
-			       rqstp->rq_xprt->xpt_locallen); \
-			memcpy(__entry->client, &rqstp->rq_xprt->xpt_remote, \
-			       rqstp->rq_xprt->xpt_remotelen); \
-		} while (0);
+#include "xdr4.h"
 
 #define NFSD_TRACE_PROC_RES_FIELDS \
 		__field(unsigned int, netns_ino) \
@@ -46,49 +34,41 @@
 			       rqstp->rq_xprt->xpt_remotelen); \
 		} while (0);
 
-TRACE_EVENT(nfsd_garbage_args_err,
+DECLARE_EVENT_CLASS(nfsd_xdr_err_class,
 	TP_PROTO(
 		const struct svc_rqst *rqstp
 	),
 	TP_ARGS(rqstp),
 	TP_STRUCT__entry(
-		NFSD_TRACE_PROC_ARG_FIELDS
-
+		__field(unsigned int, netns_ino)
+		__field(u32, xid)
 		__field(u32, vers)
 		__field(u32, proc)
+		__sockaddr(server, rqstp->rq_xprt->xpt_locallen)
+		__sockaddr(client, rqstp->rq_xprt->xpt_remotelen)
 	),
 	TP_fast_assign(
-		NFSD_TRACE_PROC_ARG_ASSIGNMENTS
+		const struct svc_xprt *xprt = rqstp->rq_xprt;
 
+		__entry->netns_ino = xprt->xpt_net->ns.inum;
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
 		__entry->vers = rqstp->rq_vers;
 		__entry->proc = rqstp->rq_proc;
+		__assign_sockaddr(server, &xprt->xpt_local, xprt->xpt_locallen);
+		__assign_sockaddr(client, &xprt->xpt_remote, xprt->xpt_remotelen);
 	),
 	TP_printk("xid=0x%08x vers=%u proc=%u",
 		__entry->xid, __entry->vers, __entry->proc
 	)
 );
 
-TRACE_EVENT(nfsd_cant_encode_err,
-	TP_PROTO(
-		const struct svc_rqst *rqstp
-	),
-	TP_ARGS(rqstp),
-	TP_STRUCT__entry(
-		NFSD_TRACE_PROC_ARG_FIELDS
-
-		__field(u32, vers)
-		__field(u32, proc)
-	),
-	TP_fast_assign(
-		NFSD_TRACE_PROC_ARG_ASSIGNMENTS
+#define DEFINE_NFSD_XDR_ERR_EVENT(name) \
+DEFINE_EVENT(nfsd_xdr_err_class, nfsd_##name##_err, \
+	TP_PROTO(const struct svc_rqst *rqstp), \
+	TP_ARGS(rqstp))
 
-		__entry->vers = rqstp->rq_vers;
-		__entry->proc = rqstp->rq_proc;
-	),
-	TP_printk("xid=0x%08x vers=%u proc=%u",
-		__entry->xid, __entry->vers, __entry->proc
-	)
-);
+DEFINE_NFSD_XDR_ERR_EVENT(garbage_args);
+DEFINE_NFSD_XDR_ERR_EVENT(cant_encode);
 
 #define show_nfsd_may_flags(x)						\
 	__print_flags(x, "|",						\
@@ -107,19 +87,26 @@
 		{ NFSD_MAY_64BIT_COOKIE,	"64BIT_COOKIE" })
 
 TRACE_EVENT(nfsd_compound,
-	TP_PROTO(const struct svc_rqst *rqst,
-		 u32 args_opcnt),
-	TP_ARGS(rqst, args_opcnt),
+	TP_PROTO(
+		const struct svc_rqst *rqst,
+		const char *tag,
+		u32 taglen,
+		u32 opcnt
+	),
+	TP_ARGS(rqst, tag, taglen, opcnt),
 	TP_STRUCT__entry(
 		__field(u32, xid)
-		__field(u32, args_opcnt)
+		__field(u32, opcnt)
+		__string_len(tag, tag, taglen)
 	),
 	TP_fast_assign(
 		__entry->xid = be32_to_cpu(rqst->rq_xid);
-		__entry->args_opcnt = args_opcnt;
+		__entry->opcnt = opcnt;
+		__assign_str_len(tag, tag, taglen);
 	),
-	TP_printk("xid=0x%08x opcnt=%u",
-		__entry->xid, __entry->args_opcnt)
+	TP_printk("xid=0x%08x opcnt=%u tag=%s",
+		__entry->xid, __entry->opcnt, __get_str(tag)
+	)
 )
 
 TRACE_EVENT(nfsd_compound_status,
@@ -194,6 +181,97 @@
 		__entry->opnum, __entry->status)
 );
 
+#define show_fs_file_type(x) \
+	__print_symbolic(x, \
+		{ S_IFLNK,		"LNK" }, \
+		{ S_IFREG,		"REG" }, \
+		{ S_IFDIR,		"DIR" }, \
+		{ S_IFCHR,		"CHR" }, \
+		{ S_IFBLK,		"BLK" }, \
+		{ S_IFIFO,		"FIFO" }, \
+		{ S_IFSOCK,		"SOCK" })
+
+TRACE_EVENT(nfsd_fh_verify,
+	TP_PROTO(
+		const struct svc_rqst *rqstp,
+		const struct svc_fh *fhp,
+		umode_t type,
+		int access
+	),
+	TP_ARGS(rqstp, fhp, type, access),
+	TP_STRUCT__entry(
+		__field(unsigned int, netns_ino)
+		__sockaddr(server, rqstp->rq_xprt->xpt_remotelen)
+		__sockaddr(client, rqstp->rq_xprt->xpt_remotelen)
+		__field(u32, xid)
+		__field(u32, fh_hash)
+		__field(const void *, inode)
+		__field(unsigned long, type)
+		__field(unsigned long, access)
+	),
+	TP_fast_assign(
+		__entry->netns_ino = SVC_NET(rqstp)->ns.inum;
+		__assign_sockaddr(server, &rqstp->rq_xprt->xpt_local,
+		       rqstp->rq_xprt->xpt_locallen);
+		__assign_sockaddr(client, &rqstp->rq_xprt->xpt_remote,
+				  rqstp->rq_xprt->xpt_remotelen);
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->fh_hash = knfsd_fh_hash(&fhp->fh_handle);
+		__entry->inode = d_inode(fhp->fh_dentry);
+		__entry->type = type;
+		__entry->access = access;
+	),
+	TP_printk("xid=0x%08x fh_hash=0x%08x type=%s access=%s",
+		__entry->xid, __entry->fh_hash,
+		show_fs_file_type(__entry->type),
+		show_nfsd_may_flags(__entry->access)
+	)
+);
+
+TRACE_EVENT_CONDITION(nfsd_fh_verify_err,
+	TP_PROTO(
+		const struct svc_rqst *rqstp,
+		const struct svc_fh *fhp,
+		umode_t type,
+		int access,
+		__be32 error
+	),
+	TP_ARGS(rqstp, fhp, type, access, error),
+	TP_CONDITION(error),
+	TP_STRUCT__entry(
+		__field(unsigned int, netns_ino)
+		__sockaddr(server, rqstp->rq_xprt->xpt_remotelen)
+		__sockaddr(client, rqstp->rq_xprt->xpt_remotelen)
+		__field(u32, xid)
+		__field(u32, fh_hash)
+		__field(const void *, inode)
+		__field(unsigned long, type)
+		__field(unsigned long, access)
+		__field(int, error)
+	),
+	TP_fast_assign(
+		__entry->netns_ino = SVC_NET(rqstp)->ns.inum;
+		__assign_sockaddr(server, &rqstp->rq_xprt->xpt_local,
+		       rqstp->rq_xprt->xpt_locallen);
+		__assign_sockaddr(client, &rqstp->rq_xprt->xpt_remote,
+				  rqstp->rq_xprt->xpt_remotelen);
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->fh_hash = knfsd_fh_hash(&fhp->fh_handle);
+		if (fhp->fh_dentry)
+			__entry->inode = d_inode(fhp->fh_dentry);
+		else
+			__entry->inode = NULL;
+		__entry->type = type;
+		__entry->access = access;
+		__entry->error = be32_to_cpu(error);
+	),
+	TP_printk("xid=0x%08x fh_hash=0x%08x type=%s access=%s error=%d",
+		__entry->xid, __entry->fh_hash,
+		show_fs_file_type(__entry->type),
+		show_nfsd_may_flags(__entry->access),
+		__entry->error
+	)
+);
 
 DECLARE_EVENT_CLASS(nfsd_fh_err_class,
 	TP_PROTO(struct svc_rqst *rqstp,
@@ -319,14 +397,14 @@
 DECLARE_EVENT_CLASS(nfsd_io_class,
 	TP_PROTO(struct svc_rqst *rqstp,
 		 struct svc_fh	*fhp,
-		 loff_t		offset,
-		 unsigned long	len),
+		 u64		offset,
+		 u32		len),
 	TP_ARGS(rqstp, fhp, offset, len),
 	TP_STRUCT__entry(
 		__field(u32, xid)
 		__field(u32, fh_hash)
-		__field(loff_t, offset)
-		__field(unsigned long, len)
+		__field(u64, offset)
+		__field(u32, len)
 	),
 	TP_fast_assign(
 		__entry->xid = be32_to_cpu(rqstp->rq_xid);
@@ -334,7 +412,7 @@
 		__entry->offset = offset;
 		__entry->len = len;
 	),
-	TP_printk("xid=0x%08x fh_hash=0x%08x offset=%lld len=%lu",
+	TP_printk("xid=0x%08x fh_hash=0x%08x offset=%llu len=%u",
 		  __entry->xid, __entry->fh_hash,
 		  __entry->offset, __entry->len)
 )
@@ -343,8 +421,8 @@
 DEFINE_EVENT(nfsd_io_class, nfsd_##name,	\
 	TP_PROTO(struct svc_rqst *rqstp,	\
 		 struct svc_fh	*fhp,		\
-		 loff_t		offset,		\
-		 unsigned long	len),		\
+		 u64		offset,		\
+		 u32		len),		\
 	TP_ARGS(rqstp, fhp, offset, len))
 
 DEFINE_NFSD_IO_EVENT(read_start);
@@ -412,10 +490,83 @@
 	)
 )
 
+DECLARE_EVENT_CLASS(nfsd_copy_err_class,
+	TP_PROTO(struct svc_rqst *rqstp,
+		 struct svc_fh	*src_fhp,
+		 loff_t		src_offset,
+		 struct svc_fh	*dst_fhp,
+		 loff_t		dst_offset,
+		 u64		count,
+		 int		status),
+	TP_ARGS(rqstp, src_fhp, src_offset, dst_fhp, dst_offset, count, status),
+	TP_STRUCT__entry(
+		__field(u32, xid)
+		__field(u32, src_fh_hash)
+		__field(loff_t, src_offset)
+		__field(u32, dst_fh_hash)
+		__field(loff_t, dst_offset)
+		__field(u64, count)
+		__field(int, status)
+	),
+	TP_fast_assign(
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->src_fh_hash = knfsd_fh_hash(&src_fhp->fh_handle);
+		__entry->src_offset = src_offset;
+		__entry->dst_fh_hash = knfsd_fh_hash(&dst_fhp->fh_handle);
+		__entry->dst_offset = dst_offset;
+		__entry->count = count;
+		__entry->status = status;
+	),
+	TP_printk("xid=0x%08x src_fh_hash=0x%08x src_offset=%lld "
+			"dst_fh_hash=0x%08x dst_offset=%lld "
+			"count=%llu status=%d",
+		  __entry->xid, __entry->src_fh_hash, __entry->src_offset,
+		  __entry->dst_fh_hash, __entry->dst_offset,
+		  (unsigned long long)__entry->count,
+		  __entry->status)
+)
+
+#define DEFINE_NFSD_COPY_ERR_EVENT(name)		\
+DEFINE_EVENT(nfsd_copy_err_class, nfsd_##name,		\
+	TP_PROTO(struct svc_rqst	*rqstp,		\
+		 struct svc_fh		*src_fhp,	\
+		 loff_t			src_offset,	\
+		 struct svc_fh		*dst_fhp,	\
+		 loff_t			dst_offset,	\
+		 u64			count,		\
+		 int			status),	\
+	TP_ARGS(rqstp, src_fhp, src_offset, dst_fhp, dst_offset, \
+		count, status))
+
+DEFINE_NFSD_COPY_ERR_EVENT(clone_file_range_err);
+
 #include "state.h"
 #include "filecache.h"
 #include "vfs.h"
 
+TRACE_EVENT(nfsd_delegret_wakeup,
+	TP_PROTO(
+		const struct svc_rqst *rqstp,
+		const struct inode *inode,
+		long timeo
+	),
+	TP_ARGS(rqstp, inode, timeo),
+	TP_STRUCT__entry(
+		__field(u32, xid)
+		__field(const void *, inode)
+		__field(long, timeo)
+	),
+	TP_fast_assign(
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->inode = inode;
+		__entry->timeo = timeo;
+	),
+	TP_printk("xid=0x%08x inode=%p%s",
+		  __entry->xid, __entry->inode,
+		  __entry->timeo == 0 ? " (timed out)" : ""
+	)
+);
+
 DECLARE_EVENT_CLASS(nfsd_stateid_class,
 	TP_PROTO(stateid_t *stp),
 	TP_ARGS(stp),
@@ -456,6 +607,7 @@
 
 DEFINE_STATEID_EVENT(open);
 DEFINE_STATEID_EVENT(deleg_read);
+DEFINE_STATEID_EVENT(deleg_return);
 DEFINE_STATEID_EVENT(deleg_recall);
 
 DECLARE_EVENT_CLASS(nfsd_stateseqid_class,
@@ -488,6 +640,61 @@
 DEFINE_STATESEQID_EVENT(preprocess);
 DEFINE_STATESEQID_EVENT(open_confirm);
 
+TRACE_DEFINE_ENUM(NFS4_OPEN_STID);
+TRACE_DEFINE_ENUM(NFS4_LOCK_STID);
+TRACE_DEFINE_ENUM(NFS4_DELEG_STID);
+TRACE_DEFINE_ENUM(NFS4_CLOSED_STID);
+TRACE_DEFINE_ENUM(NFS4_REVOKED_DELEG_STID);
+TRACE_DEFINE_ENUM(NFS4_CLOSED_DELEG_STID);
+TRACE_DEFINE_ENUM(NFS4_LAYOUT_STID);
+
+#define show_stid_type(x)						\
+	__print_flags(x, "|",						\
+		{ NFS4_OPEN_STID,		"OPEN" },		\
+		{ NFS4_LOCK_STID,		"LOCK" },		\
+		{ NFS4_DELEG_STID,		"DELEG" },		\
+		{ NFS4_CLOSED_STID,		"CLOSED" },		\
+		{ NFS4_REVOKED_DELEG_STID,	"REVOKED" },		\
+		{ NFS4_CLOSED_DELEG_STID,	"CLOSED_DELEG" },	\
+		{ NFS4_LAYOUT_STID,		"LAYOUT" })
+
+DECLARE_EVENT_CLASS(nfsd_stid_class,
+	TP_PROTO(
+		const struct nfs4_stid *stid
+	),
+	TP_ARGS(stid),
+	TP_STRUCT__entry(
+		__field(unsigned long, sc_type)
+		__field(int, sc_count)
+		__field(u32, cl_boot)
+		__field(u32, cl_id)
+		__field(u32, si_id)
+		__field(u32, si_generation)
+	),
+	TP_fast_assign(
+		const stateid_t *stp = &stid->sc_stateid;
+
+		__entry->sc_type = stid->sc_type;
+		__entry->sc_count = refcount_read(&stid->sc_count);
+		__entry->cl_boot = stp->si_opaque.so_clid.cl_boot;
+		__entry->cl_id = stp->si_opaque.so_clid.cl_id;
+		__entry->si_id = stp->si_opaque.so_id;
+		__entry->si_generation = stp->si_generation;
+	),
+	TP_printk("client %08x:%08x stateid %08x:%08x ref=%d type=%s",
+		__entry->cl_boot, __entry->cl_id,
+		__entry->si_id, __entry->si_generation,
+		__entry->sc_count, show_stid_type(__entry->sc_type)
+	)
+);
+
+#define DEFINE_STID_EVENT(name)					\
+DEFINE_EVENT(nfsd_stid_class, nfsd_stid_##name,			\
+	TP_PROTO(const struct nfs4_stid *stid),			\
+	TP_ARGS(stid))
+
+DEFINE_STID_EVENT(revoke);
+
 DECLARE_EVENT_CLASS(nfsd_clientid_class,
 	TP_PROTO(const clientid_t *clid),
 	TP_ARGS(clid),
@@ -537,6 +744,34 @@
 DEFINE_NET_EVENT(grace_start);
 DEFINE_NET_EVENT(grace_complete);
 
+TRACE_EVENT(nfsd_writeverf_reset,
+	TP_PROTO(
+		const struct nfsd_net *nn,
+		const struct svc_rqst *rqstp,
+		int error
+	),
+	TP_ARGS(nn, rqstp, error),
+	TP_STRUCT__entry(
+		__field(unsigned long long, boot_time)
+		__field(u32, xid)
+		__field(int, error)
+		__array(unsigned char, verifier, NFS4_VERIFIER_SIZE)
+	),
+	TP_fast_assign(
+		__entry->boot_time = nn->boot_time;
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->error = error;
+
+		/* avoid seqlock inside TP_fast_assign */
+		memcpy(__entry->verifier, nn->writeverf,
+		       NFS4_VERIFIER_SIZE);
+	),
+	TP_printk("boot_time=%16llx xid=0x%08x error=%d new verifier=0x%s",
+		__entry->boot_time, __entry->xid, __entry->error,
+		__print_hex_str(__entry->verifier, NFS4_VERIFIER_SIZE)
+	)
+);
+
 TRACE_EVENT(nfsd_clid_cred_mismatch,
 	TP_PROTO(
 		const struct nfs4_client *clp,
@@ -606,7 +841,7 @@
 		__array(unsigned char, addr, sizeof(struct sockaddr_in6))
 		__field(unsigned long, flavor)
 		__array(unsigned char, verifier, NFS4_VERIFIER_SIZE)
-		__string_len(name, name, clp->cl_name.len)
+		__string_len(name, clp->cl_name.data, clp->cl_name.len)
 	),
 	TP_fast_assign(
 		__entry->cl_boot = clp->cl_clientid.cl_boot;
@@ -636,25 +871,17 @@
 /*
  * from fs/nfsd/filecache.h
  */
-TRACE_DEFINE_ENUM(NFSD_FILE_HASHED);
-TRACE_DEFINE_ENUM(NFSD_FILE_PENDING);
-TRACE_DEFINE_ENUM(NFSD_FILE_BREAK_READ);
-TRACE_DEFINE_ENUM(NFSD_FILE_BREAK_WRITE);
-TRACE_DEFINE_ENUM(NFSD_FILE_REFERENCED);
-
 #define show_nf_flags(val)						\
 	__print_flags(val, "|",						\
 		{ 1 << NFSD_FILE_HASHED,	"HASHED" },		\
 		{ 1 << NFSD_FILE_PENDING,	"PENDING" },		\
-		{ 1 << NFSD_FILE_BREAK_READ,	"BREAK_READ" },		\
-		{ 1 << NFSD_FILE_BREAK_WRITE,	"BREAK_WRITE" },	\
-		{ 1 << NFSD_FILE_REFERENCED,	"REFERENCED"})
+		{ 1 << NFSD_FILE_REFERENCED,	"REFERENCED" },		\
+		{ 1 << NFSD_FILE_GC,		"GC" })
 
 DECLARE_EVENT_CLASS(nfsd_file_class,
 	TP_PROTO(struct nfsd_file *nf),
 	TP_ARGS(nf),
 	TP_STRUCT__entry(
-		__field(unsigned int, nf_hashval)
 		__field(void *, nf_inode)
 		__field(int, nf_ref)
 		__field(unsigned long, nf_flags)
@@ -662,15 +889,13 @@
 		__field(struct file *, nf_file)
 	),
 	TP_fast_assign(
-		__entry->nf_hashval = nf->nf_hashval;
 		__entry->nf_inode = nf->nf_inode;
 		__entry->nf_ref = refcount_read(&nf->nf_ref);
 		__entry->nf_flags = nf->nf_flags;
 		__entry->nf_may = nf->nf_may;
 		__entry->nf_file = nf->nf_file;
 	),
-	TP_printk("hash=0x%x inode=%p ref=%d flags=%s may=%s file=%p",
-		__entry->nf_hashval,
+	TP_printk("inode=%p ref=%d flags=%s may=%s nf_file=%p",
 		__entry->nf_inode,
 		__entry->nf_ref,
 		show_nf_flags(__entry->nf_flags),
@@ -683,34 +908,60 @@
 	TP_PROTO(struct nfsd_file *nf), \
 	TP_ARGS(nf))
 
-DEFINE_NFSD_FILE_EVENT(nfsd_file_alloc);
-DEFINE_NFSD_FILE_EVENT(nfsd_file_put_final);
+DEFINE_NFSD_FILE_EVENT(nfsd_file_free);
 DEFINE_NFSD_FILE_EVENT(nfsd_file_unhash);
 DEFINE_NFSD_FILE_EVENT(nfsd_file_put);
-DEFINE_NFSD_FILE_EVENT(nfsd_file_unhash_and_release_locked);
+DEFINE_NFSD_FILE_EVENT(nfsd_file_closing);
+DEFINE_NFSD_FILE_EVENT(nfsd_file_unhash_and_queue);
+
+TRACE_EVENT(nfsd_file_alloc,
+	TP_PROTO(
+		const struct nfsd_file *nf
+	),
+	TP_ARGS(nf),
+	TP_STRUCT__entry(
+		__field(const void *, nf_inode)
+		__field(unsigned long, nf_flags)
+		__field(unsigned long, nf_may)
+		__field(unsigned int, nf_ref)
+	),
+	TP_fast_assign(
+		__entry->nf_inode = nf->nf_inode;
+		__entry->nf_flags = nf->nf_flags;
+		__entry->nf_ref = refcount_read(&nf->nf_ref);
+		__entry->nf_may = nf->nf_may;
+	),
+	TP_printk("inode=%p ref=%u flags=%s may=%s",
+		__entry->nf_inode, __entry->nf_ref,
+		show_nf_flags(__entry->nf_flags),
+		show_nfsd_may_flags(__entry->nf_may)
+	)
+);
 
 TRACE_EVENT(nfsd_file_acquire,
-	TP_PROTO(struct svc_rqst *rqstp, unsigned int hash,
-		 struct inode *inode, unsigned int may_flags,
-		 struct nfsd_file *nf, __be32 status),
+	TP_PROTO(
+		const struct svc_rqst *rqstp,
+		const struct inode *inode,
+		unsigned int may_flags,
+		const struct nfsd_file *nf,
+		__be32 status
+	),
 
-	TP_ARGS(rqstp, hash, inode, may_flags, nf, status),
+	TP_ARGS(rqstp, inode, may_flags, nf, status),
 
 	TP_STRUCT__entry(
 		__field(u32, xid)
-		__field(unsigned int, hash)
-		__field(void *, inode)
+		__field(const void *, inode)
 		__field(unsigned long, may_flags)
-		__field(int, nf_ref)
+		__field(unsigned int, nf_ref)
 		__field(unsigned long, nf_flags)
 		__field(unsigned long, nf_may)
-		__field(struct file *, nf_file)
+		__field(const void *, nf_file)
 		__field(u32, status)
 	),
 
 	TP_fast_assign(
 		__entry->xid = be32_to_cpu(rqstp->rq_xid);
-		__entry->hash = hash;
 		__entry->inode = inode;
 		__entry->may_flags = may_flags;
 		__entry->nf_ref = nf ? refcount_read(&nf->nf_ref) : 0;
@@ -720,40 +971,132 @@
 		__entry->status = be32_to_cpu(status);
 	),
 
-	TP_printk("xid=0x%x hash=0x%x inode=%p may_flags=%s ref=%d nf_flags=%s nf_may=%s nf_file=%p status=%u",
-			__entry->xid, __entry->hash, __entry->inode,
+	TP_printk("xid=0x%x inode=%p may_flags=%s ref=%u nf_flags=%s nf_may=%s nf_file=%p status=%u",
+			__entry->xid, __entry->inode,
 			show_nfsd_may_flags(__entry->may_flags),
 			__entry->nf_ref, show_nf_flags(__entry->nf_flags),
 			show_nfsd_may_flags(__entry->nf_may),
-			__entry->nf_file, __entry->status)
+			__entry->nf_file, __entry->status
+	)
 );
 
-DECLARE_EVENT_CLASS(nfsd_file_search_class,
-	TP_PROTO(struct inode *inode, unsigned int hash, int found),
-	TP_ARGS(inode, hash, found),
+TRACE_EVENT(nfsd_file_insert_err,
+	TP_PROTO(
+		const struct svc_rqst *rqstp,
+		const struct inode *inode,
+		unsigned int may_flags,
+		long error
+	),
+	TP_ARGS(rqstp, inode, may_flags, error),
 	TP_STRUCT__entry(
-		__field(struct inode *, inode)
-		__field(unsigned int, hash)
+		__field(u32, xid)
+		__field(const void *, inode)
+		__field(unsigned long, may_flags)
+		__field(long, error)
+	),
+	TP_fast_assign(
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->inode = inode;
+		__entry->may_flags = may_flags;
+		__entry->error = error;
+	),
+	TP_printk("xid=0x%x inode=%p may_flags=%s error=%ld",
+		__entry->xid, __entry->inode,
+		show_nfsd_may_flags(__entry->may_flags),
+		__entry->error
+	)
+);
+
+TRACE_EVENT(nfsd_file_cons_err,
+	TP_PROTO(
+		const struct svc_rqst *rqstp,
+		const struct inode *inode,
+		unsigned int may_flags,
+		const struct nfsd_file *nf
+	),
+	TP_ARGS(rqstp, inode, may_flags, nf),
+	TP_STRUCT__entry(
+		__field(u32, xid)
+		__field(const void *, inode)
+		__field(unsigned long, may_flags)
+		__field(unsigned int, nf_ref)
+		__field(unsigned long, nf_flags)
+		__field(unsigned long, nf_may)
+		__field(const void *, nf_file)
+	),
+	TP_fast_assign(
+		__entry->xid = be32_to_cpu(rqstp->rq_xid);
+		__entry->inode = inode;
+		__entry->may_flags = may_flags;
+		__entry->nf_ref = refcount_read(&nf->nf_ref);
+		__entry->nf_flags = nf->nf_flags;
+		__entry->nf_may = nf->nf_may;
+		__entry->nf_file = nf->nf_file;
+	),
+	TP_printk("xid=0x%x inode=%p may_flags=%s ref=%u nf_flags=%s nf_may=%s nf_file=%p",
+		__entry->xid, __entry->inode,
+		show_nfsd_may_flags(__entry->may_flags), __entry->nf_ref,
+		show_nf_flags(__entry->nf_flags),
+		show_nfsd_may_flags(__entry->nf_may), __entry->nf_file
+	)
+);
+
+DECLARE_EVENT_CLASS(nfsd_file_open_class,
+	TP_PROTO(const struct nfsd_file *nf, __be32 status),
+	TP_ARGS(nf, status),
+	TP_STRUCT__entry(
+		__field(void *, nf_inode)	/* cannot be dereferenced */
+		__field(int, nf_ref)
+		__field(unsigned long, nf_flags)
+		__field(unsigned long, nf_may)
+		__field(void *, nf_file)	/* cannot be dereferenced */
+	),
+	TP_fast_assign(
+		__entry->nf_inode = nf->nf_inode;
+		__entry->nf_ref = refcount_read(&nf->nf_ref);
+		__entry->nf_flags = nf->nf_flags;
+		__entry->nf_may = nf->nf_may;
+		__entry->nf_file = nf->nf_file;
+	),
+	TP_printk("inode=%p ref=%d flags=%s may=%s file=%p",
+		__entry->nf_inode,
+		__entry->nf_ref,
+		show_nf_flags(__entry->nf_flags),
+		show_nfsd_may_flags(__entry->nf_may),
+		__entry->nf_file)
+)
+
+#define DEFINE_NFSD_FILE_OPEN_EVENT(name)					\
+DEFINE_EVENT(nfsd_file_open_class, name,					\
+	TP_PROTO(							\
+		const struct nfsd_file *nf,				\
+		__be32 status						\
+	),								\
+	TP_ARGS(nf, status))
+
+DEFINE_NFSD_FILE_OPEN_EVENT(nfsd_file_open);
+DEFINE_NFSD_FILE_OPEN_EVENT(nfsd_file_opened);
+
+TRACE_EVENT(nfsd_file_is_cached,
+	TP_PROTO(
+		const struct inode *inode,
+		int found
+	),
+	TP_ARGS(inode, found),
+	TP_STRUCT__entry(
+		__field(const struct inode *, inode)
 		__field(int, found)
 	),
 	TP_fast_assign(
 		__entry->inode = inode;
-		__entry->hash = hash;
 		__entry->found = found;
 	),
-	TP_printk("hash=0x%x inode=%p found=%d", __entry->hash,
-			__entry->inode, __entry->found)
+	TP_printk("inode=%p is %scached",
+		__entry->inode,
+		__entry->found ? "" : "not "
+	)
 );
 
-#define DEFINE_NFSD_FILE_SEARCH_EVENT(name)				\
-DEFINE_EVENT(nfsd_file_search_class, name,				\
-	TP_PROTO(struct inode *inode, unsigned int hash, int found),	\
-	TP_ARGS(inode, hash, found))
-
-DEFINE_NFSD_FILE_SEARCH_EVENT(nfsd_file_close_inode_sync);
-DEFINE_NFSD_FILE_SEARCH_EVENT(nfsd_file_close_inode);
-DEFINE_NFSD_FILE_SEARCH_EVENT(nfsd_file_is_cached);
-
 TRACE_EVENT(nfsd_file_fsnotify_handle_event,
 	TP_PROTO(struct inode *inode, u32 mask),
 	TP_ARGS(inode, mask),
@@ -773,6 +1116,91 @@
 			__entry->nlink, __entry->mode, __entry->mask)
 );
 
+DECLARE_EVENT_CLASS(nfsd_file_gc_class,
+	TP_PROTO(
+		const struct nfsd_file *nf
+	),
+	TP_ARGS(nf),
+	TP_STRUCT__entry(
+		__field(void *, nf_inode)
+		__field(void *, nf_file)
+		__field(int, nf_ref)
+		__field(unsigned long, nf_flags)
+	),
+	TP_fast_assign(
+		__entry->nf_inode = nf->nf_inode;
+		__entry->nf_file = nf->nf_file;
+		__entry->nf_ref = refcount_read(&nf->nf_ref);
+		__entry->nf_flags = nf->nf_flags;
+	),
+	TP_printk("inode=%p ref=%d nf_flags=%s nf_file=%p",
+		__entry->nf_inode, __entry->nf_ref,
+		show_nf_flags(__entry->nf_flags),
+		__entry->nf_file
+	)
+);
+
+#define DEFINE_NFSD_FILE_GC_EVENT(name)					\
+DEFINE_EVENT(nfsd_file_gc_class, name,					\
+	TP_PROTO(							\
+		const struct nfsd_file *nf				\
+	),								\
+	TP_ARGS(nf))
+
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_lru_add);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_lru_add_disposed);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_lru_del);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_lru_del_disposed);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_gc_in_use);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_gc_writeback);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_gc_referenced);
+DEFINE_NFSD_FILE_GC_EVENT(nfsd_file_gc_disposed);
+
+DECLARE_EVENT_CLASS(nfsd_file_lruwalk_class,
+	TP_PROTO(
+		unsigned long removed,
+		unsigned long remaining
+	),
+	TP_ARGS(removed, remaining),
+	TP_STRUCT__entry(
+		__field(unsigned long, removed)
+		__field(unsigned long, remaining)
+	),
+	TP_fast_assign(
+		__entry->removed = removed;
+		__entry->remaining = remaining;
+	),
+	TP_printk("%lu entries removed, %lu remaining",
+		__entry->removed, __entry->remaining)
+);
+
+#define DEFINE_NFSD_FILE_LRUWALK_EVENT(name)				\
+DEFINE_EVENT(nfsd_file_lruwalk_class, name,				\
+	TP_PROTO(							\
+		unsigned long removed,					\
+		unsigned long remaining					\
+	),								\
+	TP_ARGS(removed, remaining))
+
+DEFINE_NFSD_FILE_LRUWALK_EVENT(nfsd_file_gc_removed);
+DEFINE_NFSD_FILE_LRUWALK_EVENT(nfsd_file_shrinker_removed);
+
+TRACE_EVENT(nfsd_file_close,
+	TP_PROTO(
+		const struct inode *inode
+	),
+	TP_ARGS(inode),
+	TP_STRUCT__entry(
+		__field(const void *, inode)
+	),
+	TP_fast_assign(
+		__entry->inode = inode;
+	),
+	TP_printk("inode=%p",
+		__entry->inode
+	)
+);
+
 #include "cache.h"
 
 TRACE_DEFINE_ENUM(RC_DROPIT);
@@ -832,6 +1260,28 @@
 		__entry->ingress)
 );
 
+TRACE_EVENT_CONDITION(nfsd_drc_gc,
+	TP_PROTO(
+		const struct nfsd_net *nn,
+		unsigned long freed
+	),
+	TP_ARGS(nn, freed),
+	TP_CONDITION(freed > 0),
+	TP_STRUCT__entry(
+		__field(unsigned long long, boot_time)
+		__field(unsigned long, freed)
+		__field(int, total)
+	),
+	TP_fast_assign(
+		__entry->boot_time = nn->boot_time;
+		__entry->freed = freed;
+		__entry->total = atomic_read(&nn->num_drc_entries);
+	),
+	TP_printk("boot_time=%16llx total=%d freed=%lu",
+		__entry->boot_time, __entry->total, __entry->freed
+	)
+);
+
 TRACE_EVENT(nfsd_cb_args,
 	TP_PROTO(
 		const struct nfs4_client *clp,
@@ -1068,6 +1518,92 @@
 		__entry->fh_hash, __entry->count, __entry->status)
 );
 
+TRACE_EVENT(nfsd_cb_recall_any,
+	TP_PROTO(
+		const struct nfsd4_cb_recall_any *ra
+	),
+	TP_ARGS(ra),
+	TP_STRUCT__entry(
+		__field(u32, cl_boot)
+		__field(u32, cl_id)
+		__field(u32, keep)
+		__field(unsigned long, bmval0)
+		__sockaddr(addr, ra->ra_cb.cb_clp->cl_cb_conn.cb_addrlen)
+	),
+	TP_fast_assign(
+		__entry->cl_boot = ra->ra_cb.cb_clp->cl_clientid.cl_boot;
+		__entry->cl_id = ra->ra_cb.cb_clp->cl_clientid.cl_id;
+		__entry->keep = ra->ra_keep;
+		__entry->bmval0 = ra->ra_bmval[0];
+		__assign_sockaddr(addr, &ra->ra_cb.cb_clp->cl_addr,
+				  ra->ra_cb.cb_clp->cl_cb_conn.cb_addrlen);
+	),
+	TP_printk("addr=%pISpc client %08x:%08x keep=%u bmval0=%s",
+		__get_sockaddr(addr), __entry->cl_boot, __entry->cl_id,
+		__entry->keep, show_rca_mask(__entry->bmval0)
+	)
+);
+
+DECLARE_EVENT_CLASS(nfsd_cb_done_class,
+	TP_PROTO(
+		const stateid_t *stp,
+		const struct rpc_task *task
+	),
+	TP_ARGS(stp, task),
+	TP_STRUCT__entry(
+		__field(u32, cl_boot)
+		__field(u32, cl_id)
+		__field(u32, si_id)
+		__field(u32, si_generation)
+		__field(int, status)
+	),
+	TP_fast_assign(
+		__entry->cl_boot = stp->si_opaque.so_clid.cl_boot;
+		__entry->cl_id = stp->si_opaque.so_clid.cl_id;
+		__entry->si_id = stp->si_opaque.so_id;
+		__entry->si_generation = stp->si_generation;
+		__entry->status = task->tk_status;
+	),
+	TP_printk("client %08x:%08x stateid %08x:%08x status=%d",
+		__entry->cl_boot, __entry->cl_id, __entry->si_id,
+		__entry->si_generation, __entry->status
+	)
+);
+
+#define DEFINE_NFSD_CB_DONE_EVENT(name)			\
+DEFINE_EVENT(nfsd_cb_done_class, name,			\
+	TP_PROTO(					\
+		const stateid_t *stp,			\
+		const struct rpc_task *task		\
+	),						\
+	TP_ARGS(stp, task))
+
+DEFINE_NFSD_CB_DONE_EVENT(nfsd_cb_recall_done);
+DEFINE_NFSD_CB_DONE_EVENT(nfsd_cb_notify_lock_done);
+DEFINE_NFSD_CB_DONE_EVENT(nfsd_cb_layout_done);
+DEFINE_NFSD_CB_DONE_EVENT(nfsd_cb_offload_done);
+
+TRACE_EVENT(nfsd_cb_recall_any_done,
+	TP_PROTO(
+		const struct nfsd4_callback *cb,
+		const struct rpc_task *task
+	),
+	TP_ARGS(cb, task),
+	TP_STRUCT__entry(
+		__field(u32, cl_boot)
+		__field(u32, cl_id)
+		__field(int, status)
+	),
+	TP_fast_assign(
+		__entry->status = task->tk_status;
+		__entry->cl_boot = cb->cb_clp->cl_clientid.cl_boot;
+		__entry->cl_id = cb->cb_clp->cl_clientid.cl_id;
+	),
+	TP_printk("client %08x:%08x status=%d",
+		__entry->cl_boot, __entry->cl_id, __entry->status
+	)
+);
+
 #endif /* _NFSD_TRACE_H */
 
 #undef TRACE_INCLUDE_PATH
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/vfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/vfs.c
@@ -32,14 +32,13 @@
 #include <linux/writeback.h>
 #include <linux/security.h>
 
-#ifdef CONFIG_NFSD_V3
 #include "xdr3.h"
-#endif /* CONFIG_NFSD_V3 */
 
 #ifdef CONFIG_NFSD_V4
 #include "../internal.h"
 #include "acl.h"
 #include "idmap.h"
+#include "xdr4.h"
 #endif /* CONFIG_NFSD_V4 */
 
 #include "nfsd.h"
@@ -49,6 +48,70 @@
 
 #define NFSDDBG_FACILITY		NFSDDBG_FILEOP
 
+/**
+ * nfserrno - Map Linux errnos to NFS errnos
+ * @errno: POSIX(-ish) error code to be mapped
+ *
+ * Returns the appropriate (net-endian) nfserr_* (or nfs_ok if errno is 0). If
+ * it's an error we don't expect, log it once and return nfserr_io.
+ */
+__be32
+nfserrno (int errno)
+{
+	static struct {
+		__be32	nfserr;
+		int	syserr;
+	} nfs_errtbl[] = {
+		{ nfs_ok, 0 },
+		{ nfserr_perm, -EPERM },
+		{ nfserr_noent, -ENOENT },
+		{ nfserr_io, -EIO },
+		{ nfserr_nxio, -ENXIO },
+		{ nfserr_fbig, -E2BIG },
+		{ nfserr_stale, -EBADF },
+		{ nfserr_acces, -EACCES },
+		{ nfserr_exist, -EEXIST },
+		{ nfserr_xdev, -EXDEV },
+		{ nfserr_mlink, -EMLINK },
+		{ nfserr_nodev, -ENODEV },
+		{ nfserr_notdir, -ENOTDIR },
+		{ nfserr_isdir, -EISDIR },
+		{ nfserr_inval, -EINVAL },
+		{ nfserr_fbig, -EFBIG },
+		{ nfserr_nospc, -ENOSPC },
+		{ nfserr_rofs, -EROFS },
+		{ nfserr_mlink, -EMLINK },
+		{ nfserr_nametoolong, -ENAMETOOLONG },
+		{ nfserr_notempty, -ENOTEMPTY },
+		{ nfserr_dquot, -EDQUOT },
+		{ nfserr_stale, -ESTALE },
+		{ nfserr_jukebox, -ETIMEDOUT },
+		{ nfserr_jukebox, -ERESTARTSYS },
+		{ nfserr_jukebox, -EAGAIN },
+		{ nfserr_jukebox, -EWOULDBLOCK },
+		{ nfserr_jukebox, -ENOMEM },
+		{ nfserr_io, -ETXTBSY },
+		{ nfserr_notsupp, -EOPNOTSUPP },
+		{ nfserr_toosmall, -ETOOSMALL },
+		{ nfserr_serverfault, -ESERVERFAULT },
+		{ nfserr_serverfault, -ENFILE },
+		{ nfserr_io, -EREMOTEIO },
+		{ nfserr_stale, -EOPENSTALE },
+		{ nfserr_io, -EUCLEAN },
+		{ nfserr_perm, -ENOKEY },
+		{ nfserr_no_grace, -ENOGRACE},
+		{ nfserr_io, -EBADMSG },
+	};
+	int	i;
+
+	for (i = 0; i < ARRAY_SIZE(nfs_errtbl); i++) {
+		if (nfs_errtbl[i].syserr == errno)
+			return nfs_errtbl[i].nfserr;
+	}
+	WARN_ONCE(1, "nfsd: non-standard errno: %d\n", errno);
+	return nfserr_io;
+}
+
 /* 
  * Called from nfsd_lookup and encode_dirent. Check if we have crossed 
  * a mount point.
@@ -199,27 +262,13 @@
 				goto out_nfserr;
 		}
 	} else {
-		/*
-		 * In the nfsd4_open() case, this may be held across
-		 * subsequent open and delegation acquisition which may
-		 * need to take the child's i_mutex:
-		 */
-		fh_lock_nested(fhp, I_MUTEX_PARENT);
-		dentry = lookup_one_len(name, dparent, len);
+		dentry = lookup_one_len_unlocked(name, dparent, len);
 		host_err = PTR_ERR(dentry);
 		if (IS_ERR(dentry))
 			goto out_nfserr;
 		if (nfsd_mountpoint(dentry, exp)) {
-			/*
-			 * We don't need the i_mutex after all.  It's
-			 * still possible we could open this (regular
-			 * files can be mountpoints too), but the
-			 * i_mutex is just there to prevent renames of
-			 * something that we might be about to delegate,
-			 * and a mountpoint won't be renamed:
-			 */
-			fh_unlock(fhp);
-			if ((host_err = nfsd_cross_mnt(rqstp, &dentry, &exp))) {
+			host_err = nfsd_cross_mnt(rqstp, &dentry, &exp);
+			if (host_err) {
 				dput(dentry);
 				goto out_nfserr;
 			}
@@ -234,7 +283,15 @@
 	return nfserrno(host_err);
 }
 
-/*
+/**
+ * nfsd_lookup - look up a single path component for nfsd
+ *
+ * @rqstp:   the request context
+ * @fhp:     the file handle of the directory
+ * @name:    the component name, or %NULL to look up parent
+ * @len:     length of name to examine
+ * @resfh:   pointer to pre-initialised filehandle to hold result.
+ *
  * Look up one component of a pathname.
  * N.B. After this call _both_ fhp and resfh need an fh_put
  *
@@ -244,10 +301,11 @@
  * returned. Otherwise the covered directory is returned.
  * NOTE: this mountpoint crossing is not supported properly by all
  *   clients and is explicitly disallowed for NFSv3
+ *
  */
 __be32
 nfsd_lookup(struct svc_rqst *rqstp, struct svc_fh *fhp, const char *name,
-				unsigned int len, struct svc_fh *resfh)
+	    unsigned int len, struct svc_fh *resfh)
 {
 	struct svc_export	*exp;
 	struct dentry		*dentry;
@@ -305,6 +363,10 @@
 static void
 nfsd_sanitize_attrs(struct inode *inode, struct iattr *iap)
 {
+	/* Ignore mode updates on symlinks */
+	if (S_ISLNK(inode->i_mode))
+		iap->ia_valid &= ~ATTR_MODE;
+
 	/* sanitize the mode change */
 	if (iap->ia_valid & ATTR_MODE) {
 		iap->ia_mode &= S_IALLUGO;
@@ -322,7 +384,9 @@
 				iap->ia_mode &= ~S_ISGID;
 		} else {
 			/* set ATTR_KILL_* bits and let VFS handle it */
-			iap->ia_valid |= (ATTR_KILL_SUID | ATTR_KILL_SGID);
+			iap->ia_valid |= ATTR_KILL_SUID;
+			iap->ia_valid |=
+				setattr_should_drop_sgid(&init_user_ns, inode);
 		}
 	}
 }
@@ -344,21 +408,77 @@
 	return nfserrno(get_write_access(inode));
 }
 
-/*
- * Set various file attributes.  After this call fhp needs an fh_put.
+static int __nfsd_setattr(struct dentry *dentry, struct iattr *iap)
+{
+	int host_err;
+
+	if (iap->ia_valid & ATTR_SIZE) {
+		/*
+		 * RFC5661, Section 18.30.4:
+		 *   Changing the size of a file with SETATTR indirectly
+		 *   changes the time_modify and change attributes.
+		 *
+		 * (and similar for the older RFCs)
+		 */
+		struct iattr size_attr = {
+			.ia_valid	= ATTR_SIZE | ATTR_CTIME | ATTR_MTIME,
+			.ia_size	= iap->ia_size,
+		};
+
+		if (iap->ia_size < 0)
+			return -EFBIG;
+
+		host_err = notify_change(&init_user_ns, dentry, &size_attr, NULL);
+		if (host_err)
+			return host_err;
+		iap->ia_valid &= ~ATTR_SIZE;
+
+		/*
+		 * Avoid the additional setattr call below if the only other
+		 * attribute that the client sends is the mtime, as we update
+		 * it as part of the size change above.
+		 */
+		if ((iap->ia_valid & ~ATTR_MTIME) == 0)
+			return 0;
+	}
+
+	if (!iap->ia_valid)
+		return 0;
+
+	iap->ia_valid |= ATTR_CTIME;
+	return notify_change(&init_user_ns, dentry, iap, NULL);
+}
+
+/**
+ * nfsd_setattr - Set various file attributes.
+ * @rqstp: controlling RPC transaction
+ * @fhp: filehandle of target
+ * @attr: attributes to set
+ * @check_guard: set to 1 if guardtime is a valid timestamp
+ * @guardtime: do not act if ctime.tv_sec does not match this timestamp
+ *
+ * This call may adjust the contents of @attr (in particular, this
+ * call may change the bits in the na_iattr.ia_valid field).
+ *
+ * Returns nfs_ok on success, otherwise an NFS status code is
+ * returned. Caller must release @fhp by calling fh_put in either
+ * case.
  */
 __be32
-nfsd_setattr(struct svc_rqst *rqstp, struct svc_fh *fhp, struct iattr *iap,
+nfsd_setattr(struct svc_rqst *rqstp, struct svc_fh *fhp,
+	     struct nfsd_attrs *attr,
 	     int check_guard, time64_t guardtime)
 {
 	struct dentry	*dentry;
 	struct inode	*inode;
+	struct iattr	*iap = attr->na_iattr;
 	int		accmode = NFSD_MAY_SATTR;
 	umode_t		ftype = 0;
 	__be32		err;
-	int		host_err;
+	int		host_err = 0;
 	bool		get_write_count;
 	bool		size_change = (iap->ia_valid & ATTR_SIZE);
+	int		retries;
 
 	if (iap->ia_valid & ATTR_SIZE) {
 		accmode |= NFSD_MAY_WRITE|NFSD_MAY_OWNER_OVERRIDE;
@@ -394,13 +514,6 @@
 	dentry = fhp->fh_dentry;
 	inode = d_inode(dentry);
 
-	/* Ignore any mode updates on symlinks */
-	if (S_ISLNK(inode->i_mode))
-		iap->ia_valid &= ~ATTR_MODE;
-
-	if (!iap->ia_valid)
-		return 0;
-
 	nfsd_sanitize_attrs(inode, iap);
 
 	if (check_guard && guardtime != inode->i_ctime.tv_sec)
@@ -419,45 +532,43 @@
 			return err;
 	}
 
-	fh_lock(fhp);
-	if (size_change) {
-		/*
-		 * RFC5661, Section 18.30.4:
-		 *   Changing the size of a file with SETATTR indirectly
-		 *   changes the time_modify and change attributes.
-		 *
-		 * (and similar for the older RFCs)
-		 */
-		struct iattr size_attr = {
-			.ia_valid	= ATTR_SIZE | ATTR_CTIME | ATTR_MTIME,
-			.ia_size	= iap->ia_size,
-		};
-
-		host_err = notify_change(&init_user_ns, dentry, &size_attr, NULL);
-		if (host_err)
-			goto out_unlock;
-		iap->ia_valid &= ~ATTR_SIZE;
+	inode_lock(inode);
+	fh_fill_pre_attrs(fhp);
+	for (retries = 1;;) {
+		struct iattr attrs;
 
 		/*
-		 * Avoid the additional setattr call below if the only other
-		 * attribute that the client sends is the mtime, as we update
-		 * it as part of the size change above.
+		 * notify_change() can alter its iattr argument, making
+		 * @iap unsuitable for submission multiple times. Make a
+		 * copy for every loop iteration.
 		 */
-		if ((iap->ia_valid & ~ATTR_MTIME) == 0)
-			goto out_unlock;
+		attrs = *iap;
+		host_err = __nfsd_setattr(dentry, &attrs);
+		if (host_err != -EAGAIN || !retries--)
+			break;
+		if (!nfsd_wait_for_delegreturn(rqstp, inode))
+			break;
 	}
-
-	iap->ia_valid |= ATTR_CTIME;
-	host_err = notify_change(&init_user_ns, dentry, iap, NULL);
-
-out_unlock:
-	fh_unlock(fhp);
+	if (attr->na_seclabel && attr->na_seclabel->len)
+		attr->na_labelerr = security_inode_setsecctx(dentry,
+			attr->na_seclabel->data, attr->na_seclabel->len);
+	if (IS_ENABLED(CONFIG_FS_POSIX_ACL) && attr->na_pacl)
+		attr->na_aclerr = set_posix_acl(&init_user_ns,
+						inode, ACL_TYPE_ACCESS,
+						attr->na_pacl);
+	if (IS_ENABLED(CONFIG_FS_POSIX_ACL) &&
+	    !attr->na_aclerr && attr->na_dpacl && S_ISDIR(inode->i_mode))
+		attr->na_aclerr = set_posix_acl(&init_user_ns,
+						inode, ACL_TYPE_DEFAULT,
+						attr->na_dpacl);
+	fh_fill_post_attrs(fhp);
+	inode_unlock(inode);
 	if (size_change)
 		put_write_access(inode);
 out:
 	if (!host_err)
 		host_err = commit_metadata(fhp);
-	return nfserrno(host_err);
+	return err != 0 ? err : nfserrno(host_err);
 }
 
 #if defined(CONFIG_NFSD_V4)
@@ -489,42 +600,24 @@
 		return 0;
 	return 1;
 }
-#ifdef CONFIG_NFSD_V4_SECURITY_LABEL
-__be32 nfsd4_set_nfs4_label(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		struct xdr_netobj *label)
-{
-	__be32 error;
-	int host_error;
-	struct dentry *dentry;
-
-	error = fh_verify(rqstp, fhp, 0 /* S_IFREG */, NFSD_MAY_SATTR);
-	if (error)
-		return error;
 
-	dentry = fhp->fh_dentry;
-
-	inode_lock(d_inode(dentry));
-	host_error = security_inode_setsecctx(dentry, label->data, label->len);
-	inode_unlock(d_inode(dentry));
-	return nfserrno(host_error);
-}
-#else
-__be32 nfsd4_set_nfs4_label(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		struct xdr_netobj *label)
+static struct nfsd4_compound_state *nfsd4_get_cstate(struct svc_rqst *rqstp)
 {
-	return nfserr_notsupp;
+	return &((struct nfsd4_compoundres *)rqstp->rq_resp)->cstate;
 }
-#endif
 
-__be32 nfsd4_clone_file_range(struct nfsd_file *nf_src, u64 src_pos,
-		struct nfsd_file *nf_dst, u64 dst_pos, u64 count, bool sync)
+__be32 nfsd4_clone_file_range(struct svc_rqst *rqstp,
+		struct nfsd_file *nf_src, u64 src_pos,
+		struct nfsd_file *nf_dst, u64 dst_pos,
+		u64 count, bool sync)
 {
 	struct file *src = nf_src->nf_file;
 	struct file *dst = nf_dst->nf_file;
+	errseq_t since;
 	loff_t cloned;
 	__be32 ret = 0;
 
-	down_write(&nf_dst->nf_rwsem);
+	since = READ_ONCE(dst->f_wb_err);
 	cloned = vfs_clone_file_range(src, src_pos, dst, dst_pos, count, 0);
 	if (cloned < 0) {
 		ret = nfserrno(cloned);
@@ -539,21 +632,32 @@
 		int status = vfs_fsync_range(dst, dst_pos, dst_end, 0);
 
 		if (!status)
+			status = filemap_check_wb_err(dst->f_mapping, since);
+		if (!status)
 			status = commit_inode_metadata(file_inode(src));
 		if (status < 0) {
-			nfsd_reset_boot_verifier(net_generic(nf_dst->nf_net,
-						 nfsd_net_id));
+			struct nfsd_net *nn = net_generic(nf_dst->nf_net,
+							  nfsd_net_id);
+
+			trace_nfsd_clone_file_range_err(rqstp,
+					&nfsd4_get_cstate(rqstp)->save_fh,
+					src_pos,
+					&nfsd4_get_cstate(rqstp)->current_fh,
+					dst_pos,
+					count, status);
+			nfsd_reset_write_verifier(nn);
+			trace_nfsd_writeverf_reset(nn, rqstp, status);
 			ret = nfserrno(status);
 		}
 	}
 out_err:
-	up_write(&nf_dst->nf_rwsem);
 	return ret;
 }
 
 ssize_t nfsd_copy_file_range(struct file *src, u64 src_pos, struct file *dst,
 			     u64 dst_pos, u64 count)
 {
+	ssize_t ret;
 
 	/*
 	 * Limit copy to 4MB to prevent indefinitely blocking an nfsd
@@ -564,7 +668,12 @@
 	 * limit like this and pipeline multiple COPY requests.
 	 */
 	count = min_t(u64, count, 1 << 22);
-	return vfs_copy_file_range(src, src_pos, dst, dst_pos, count, 0);
+	ret = vfs_copy_file_range(src, src_pos, dst, dst_pos, count, 0);
+
+	if (ret == -EOPNOTSUPP || ret == -EXDEV)
+		ret = vfs_copy_file_range(src, src_pos, dst, dst_pos, count,
+					  COPY_FILE_SPLICE);
+	return ret;
 }
 
 __be32 nfsd4_vfs_fallocate(struct svc_rqst *rqstp, struct svc_fh *fhp,
@@ -584,7 +693,6 @@
 }
 #endif /* defined(CONFIG_NFSD_V4) */
 
-#ifdef CONFIG_NFSD_V3
 /*
  * Check server access rights to a file system object
  */
@@ -696,7 +804,6 @@
  out:
 	return error;
 }
-#endif /* CONFIG_NFSD_V3 */
 
 int nfsd_open_break_lease(struct inode *inode, int access)
 {
@@ -729,9 +836,6 @@
 	path.dentry = fhp->fh_dentry;
 	inode = d_inode(path.dentry);
 
-	/* Disallow write access to files with the append-only bit set
-	 * or any access when mandatory locking enabled
-	 */
 	err = nfserr_perm;
 	if (IS_APPEND(inode) && (may_flags & NFSD_MAY_WRITE))
 		goto out;
@@ -779,6 +883,7 @@
 		int may_flags, struct file **filp)
 {
 	__be32 err;
+	bool retried = false;
 
 	validate_process_creds();
 	/*
@@ -794,21 +899,37 @@
 	 */
 	if (type == S_IFREG)
 		may_flags |= NFSD_MAY_OWNER_OVERRIDE;
+retry:
 	err = fh_verify(rqstp, fhp, type, may_flags);
-	if (!err)
+	if (!err) {
 		err = __nfsd_open(rqstp, fhp, type, may_flags, filp);
+		if (err == nfserr_stale && !retried) {
+			retried = true;
+			fh_put(fhp);
+			goto retry;
+		}
+	}
 	validate_process_creds();
 	return err;
 }
 
+/**
+ * nfsd_open_verified - Open a regular file for the filecache
+ * @rqstp: RPC request
+ * @fhp: NFS filehandle of the file to open
+ * @may_flags: internal permission flags
+ * @filp: OUT: open "struct file *"
+ *
+ * Returns an nfsstat value in network byte order.
+ */
 __be32
-nfsd_open_verified(struct svc_rqst *rqstp, struct svc_fh *fhp, umode_t type,
-		int may_flags, struct file **filp)
+nfsd_open_verified(struct svc_rqst *rqstp, struct svc_fh *fhp, int may_flags,
+		   struct file **filp)
 {
 	__be32 err;
 
 	validate_process_creds();
-	err = __nfsd_open(rqstp, fhp, type, may_flags, filp);
+	err = __nfsd_open(rqstp, fhp, S_IFREG, may_flags, filp);
 	validate_process_creds();
 	return err;
 }
@@ -823,17 +944,23 @@
 		  struct splice_desc *sd)
 {
 	struct svc_rqst *rqstp = sd->u.data;
-	struct page **pp = rqstp->rq_next_page;
-	struct page *page = buf->page;
+	struct page *page = buf->page;	// may be a compound one
+	unsigned offset = buf->offset;
+	struct page *last_page;
 
-	if (rqstp->rq_res.page_len == 0) {
-		svc_rqst_replace_page(rqstp, page);
-		rqstp->rq_res.page_base = buf->offset;
-	} else if (page != pp[-1]) {
+	last_page = page + (offset + sd->len - 1) / PAGE_SIZE;
+	for (page += offset / PAGE_SIZE; page <= last_page; page++) {
+		/*
+		 * Skip page replacement when extending the contents
+		 * of the current page.
+		 */
+		if (page == *(rqstp->rq_next_page - 1))
+			continue;
 		svc_rqst_replace_page(rqstp, page);
 	}
+	if (rqstp->rq_res.page_len == 0)	// first call
+		rqstp->rq_res.page_base = offset % PAGE_SIZE;
 	rqstp->rq_res.page_len += sd->len;
-
 	return sd->len;
 }
 
@@ -858,7 +985,9 @@
 			       unsigned long *count, u32 *eof, ssize_t host_err)
 {
 	if (host_err >= 0) {
-		nfsd_stats_io_read_add(fhp->fh_export, host_err);
+		struct nfsd_net *nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
+
+		nfsd_stats_io_read_add(nn, fhp->fh_export, host_err);
 		*eof = nfsd_eof_on_read(file, offset, host_err, *count);
 		*count = host_err;
 		fsnotify_access(file);
@@ -946,10 +1075,12 @@
 				unsigned long *cnt, int stable,
 				__be32 *verf)
 {
+	struct nfsd_net		*nn = net_generic(SVC_NET(rqstp), nfsd_net_id);
 	struct file		*file = nf->nf_file;
 	struct super_block	*sb = file_inode(file)->i_sb;
 	struct svc_export	*exp;
 	struct iov_iter		iter;
+	errseq_t		since;
 	__be32			nfserr;
 	int			host_err;
 	int			use_wgather;
@@ -987,36 +1118,30 @@
 		flags |= RWF_SYNC;
 
 	iov_iter_kvec(&iter, WRITE, vec, vlen, *cnt);
-	if (flags & RWF_SYNC) {
-		down_write(&nf->nf_rwsem);
-		host_err = vfs_iter_write(file, &iter, &pos, flags);
-		if (host_err < 0)
-			nfsd_reset_boot_verifier(net_generic(SVC_NET(rqstp),
-						 nfsd_net_id));
-		up_write(&nf->nf_rwsem);
-	} else {
-		down_read(&nf->nf_rwsem);
-		if (verf)
-			nfsd_copy_boot_verifier(verf,
-					net_generic(SVC_NET(rqstp),
-					nfsd_net_id));
-		host_err = vfs_iter_write(file, &iter, &pos, flags);
-		up_read(&nf->nf_rwsem);
-	}
+	since = READ_ONCE(file->f_wb_err);
+	if (verf)
+		nfsd_copy_write_verifier(verf, nn);
+	file_start_write(file);
+	host_err = vfs_iter_write(file, &iter, &pos, flags);
+	file_end_write(file);
 	if (host_err < 0) {
-		nfsd_reset_boot_verifier(net_generic(SVC_NET(rqstp),
-					 nfsd_net_id));
+		nfsd_reset_write_verifier(nn);
+		trace_nfsd_writeverf_reset(nn, rqstp, host_err);
 		goto out_nfserr;
 	}
 	*cnt = host_err;
-	nfsd_stats_io_write_add(exp, *cnt);
+	nfsd_stats_io_write_add(nn, exp, *cnt);
 	fsnotify_modify(file);
+	host_err = filemap_check_wb_err(file->f_mapping, since);
+	if (host_err < 0)
+		goto out_nfserr;
 
 	if (stable && use_wgather) {
 		host_err = wait_for_concurrent_writes(file);
-		if (host_err < 0)
-			nfsd_reset_boot_verifier(net_generic(SVC_NET(rqstp),
-						 nfsd_net_id));
+		if (host_err < 0) {
+			nfsd_reset_write_verifier(nn);
+			trace_nfsd_writeverf_reset(nn, rqstp, host_err);
+		}
 	}
 
 out_nfserr:
@@ -1046,7 +1171,7 @@
 	__be32 err;
 
 	trace_nfsd_read_start(rqstp, fhp, offset, *count);
-	err = nfsd_file_acquire(rqstp, fhp, NFSD_MAY_READ, &nf);
+	err = nfsd_file_acquire_gc(rqstp, fhp, NFSD_MAY_READ, &nf);
 	if (err)
 		return err;
 
@@ -1078,7 +1203,7 @@
 
 	trace_nfsd_write_start(rqstp, fhp, offset, *cnt);
 
-	err = nfsd_file_acquire(rqstp, fhp, NFSD_MAY_WRITE, &nf);
+	err = nfsd_file_acquire_gc(rqstp, fhp, NFSD_MAY_WRITE, &nf);
 	if (err)
 		goto out;
 
@@ -1090,87 +1215,98 @@
 	return err;
 }
 
-#ifdef CONFIG_NFSD_V3
-static int
-nfsd_filemap_write_and_wait_range(struct nfsd_file *nf, loff_t offset,
-				  loff_t end)
-{
-	struct address_space *mapping = nf->nf_file->f_mapping;
-	int ret = filemap_fdatawrite_range(mapping, offset, end);
-
-	if (ret)
-		return ret;
-	filemap_fdatawait_range_keep_errors(mapping, offset, end);
-	return 0;
-}
-
-/*
- * Commit all pending writes to stable storage.
+/**
+ * nfsd_commit - Commit pending writes to stable storage
+ * @rqstp: RPC request being processed
+ * @fhp: NFS filehandle
+ * @nf: target file
+ * @offset: raw offset from beginning of file
+ * @count: raw count of bytes to sync
+ * @verf: filled in with the server's current write verifier
  *
- * Note: we only guarantee that data that lies within the range specified
- * by the 'offset' and 'count' parameters will be synced.
+ * Note: we guarantee that data that lies within the range specified
+ * by the 'offset' and 'count' parameters will be synced. The server
+ * is permitted to sync data that lies outside this range at the
+ * same time.
  *
  * Unfortunately we cannot lock the file to make sure we return full WCC
  * data to the client, as locking happens lower down in the filesystem.
+ *
+ * Return values:
+ *   An nfsstat value in network byte order.
  */
 __be32
-nfsd_commit(struct svc_rqst *rqstp, struct svc_fh *fhp,
-               loff_t offset, unsigned long count, __be32 *verf)
+nfsd_commit(struct svc_rqst *rqstp, struct svc_fh *fhp, struct nfsd_file *nf,
+	    u64 offset, u32 count, __be32 *verf)
 {
-	struct nfsd_file	*nf;
-	loff_t			end = LLONG_MAX;
-	__be32			err = nfserr_inval;
+	__be32			err = nfs_ok;
+	u64			maxbytes;
+	loff_t			start, end;
+	struct nfsd_net		*nn;
 
-	if (offset < 0)
-		goto out;
-	if (count != 0) {
-		end = offset + (loff_t)count - 1;
-		if (end < offset)
-			goto out;
+	/*
+	 * Convert the client-provided (offset, count) range to a
+	 * (start, end) range. If the client-provided range falls
+	 * outside the maximum file size of the underlying FS,
+	 * clamp the sync range appropriately.
+	 */
+	start = 0;
+	end = LLONG_MAX;
+	maxbytes = (u64)fhp->fh_dentry->d_sb->s_maxbytes;
+	if (offset < maxbytes) {
+		start = offset;
+		if (count && (offset + count - 1 < maxbytes))
+			end = offset + count - 1;
 	}
 
-	err = nfsd_file_acquire(rqstp, fhp,
-			NFSD_MAY_WRITE|NFSD_MAY_NOT_BREAK_LEASE, &nf);
-	if (err)
-		goto out;
+	nn = net_generic(nf->nf_net, nfsd_net_id);
 	if (EX_ISSYNC(fhp->fh_export)) {
-		int err2 = nfsd_filemap_write_and_wait_range(nf, offset, end);
+		errseq_t since = READ_ONCE(nf->nf_file->f_wb_err);
+		int err2;
 
-		down_write(&nf->nf_rwsem);
-		if (!err2)
-			err2 = vfs_fsync_range(nf->nf_file, offset, end, 0);
+		err2 = vfs_fsync_range(nf->nf_file, start, end, 0);
 		switch (err2) {
 		case 0:
-			nfsd_copy_boot_verifier(verf, net_generic(nf->nf_net,
-						nfsd_net_id));
+			nfsd_copy_write_verifier(verf, nn);
+			err2 = filemap_check_wb_err(nf->nf_file->f_mapping,
+						    since);
+			err = nfserrno(err2);
 			break;
 		case -EINVAL:
 			err = nfserr_notsupp;
 			break;
 		default:
+			nfsd_reset_write_verifier(nn);
+			trace_nfsd_writeverf_reset(nn, rqstp, err2);
 			err = nfserrno(err2);
-			nfsd_reset_boot_verifier(net_generic(nf->nf_net,
-						 nfsd_net_id));
 		}
-		up_write(&nf->nf_rwsem);
 	} else
-		nfsd_copy_boot_verifier(verf, net_generic(nf->nf_net,
-					nfsd_net_id));
+		nfsd_copy_write_verifier(verf, nn);
 
-	nfsd_file_put(nf);
-out:
 	return err;
 }
-#endif /* CONFIG_NFSD_V3 */
 
-static __be32
-nfsd_create_setattr(struct svc_rqst *rqstp, struct svc_fh *resfhp,
-			struct iattr *iap)
+/**
+ * nfsd_create_setattr - Set a created file's attributes
+ * @rqstp: RPC transaction being executed
+ * @fhp: NFS filehandle of parent directory
+ * @resfhp: NFS filehandle of new object
+ * @attrs: requested attributes of new object
+ *
+ * Returns nfs_ok on success, or an nfsstat in network byte order.
+ */
+__be32
+nfsd_create_setattr(struct svc_rqst *rqstp, struct svc_fh *fhp,
+		    struct svc_fh *resfhp, struct nfsd_attrs *attrs)
 {
+	struct iattr *iap = attrs->na_iattr;
+	__be32 status;
+
 	/*
-	 * Mode has already been set earlier in create:
+	 * Mode has already been set by file creation.
 	 */
 	iap->ia_valid &= ~ATTR_MODE;
+
 	/*
 	 * Setting uid/gid works only for root.  Irix appears to
 	 * send along the gid on create when it tries to implement
@@ -1178,10 +1314,31 @@
 	 */
 	if (!uid_eq(current_fsuid(), GLOBAL_ROOT_UID))
 		iap->ia_valid &= ~(ATTR_UID|ATTR_GID);
+
+	/*
+	 * Callers expect new file metadata to be committed even
+	 * if the attributes have not changed.
+	 */
 	if (iap->ia_valid)
-		return nfsd_setattr(rqstp, resfhp, iap, 0, (time64_t)0);
-	/* Callers expect file metadata to be committed here */
-	return nfserrno(commit_metadata(resfhp));
+		status = nfsd_setattr(rqstp, resfhp, attrs, 0, (time64_t)0);
+	else
+		status = nfserrno(commit_metadata(resfhp));
+
+	/*
+	 * Transactional filesystems had a chance to commit changes
+	 * for both parent and child simultaneously making the
+	 * following commit_metadata a noop in many cases.
+	 */
+	if (!status)
+		status = nfserrno(commit_metadata(fhp));
+
+	/*
+	 * Update the new filehandle to pick up the new attributes.
+	 */
+	if (!status)
+		status = fh_update(resfhp);
+
+	return status;
 }
 
 /* HPUX client sometimes creates a file in mode 000, and sets size to 0.
@@ -1202,26 +1359,19 @@
 /* The parent directory should already be locked: */
 __be32
 nfsd_create_locked(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		char *fname, int flen, struct iattr *iap,
-		int type, dev_t rdev, struct svc_fh *resfhp)
+		   struct nfsd_attrs *attrs,
+		   int type, dev_t rdev, struct svc_fh *resfhp)
 {
 	struct dentry	*dentry, *dchild;
 	struct inode	*dirp;
+	struct iattr	*iap = attrs->na_iattr;
 	__be32		err;
-	__be32		err2;
 	int		host_err;
 
 	dentry = fhp->fh_dentry;
 	dirp = d_inode(dentry);
 
 	dchild = dget(resfhp->fh_dentry);
-	if (!fhp->fh_locked) {
-		WARN_ONCE(1, "nfsd_create: parent %pd2 not locked!\n",
-				dentry);
-		err = nfserr_io;
-		goto out;
-	}
-
 	err = nfsd_permission(rqstp, fhp->fh_export, dentry, NFSD_MAY_CREATE);
 	if (err)
 		goto out;
@@ -1234,7 +1384,6 @@
 		iap->ia_mode &= ~current_umask();
 
 	err = 0;
-	host_err = 0;
 	switch (type) {
 	case S_IFREG:
 		host_err = vfs_create(&init_user_ns, dirp, dchild, iap->ia_mode, true);
@@ -1281,22 +1430,8 @@
 	if (host_err < 0)
 		goto out_nfserr;
 
-	err = nfsd_create_setattr(rqstp, resfhp, iap);
+	err = nfsd_create_setattr(rqstp, fhp, resfhp, attrs);
 
-	/*
-	 * nfsd_create_setattr already committed the child.  Transactional
-	 * filesystems had a chance to commit changes for both parent and
-	 * child simultaneously making the following commit_metadata a
-	 * noop.
-	 */
-	err2 = nfserrno(commit_metadata(fhp));
-	if (err2)
-		err = err2;
-	/*
-	 * Update the file handle to get the new inode info.
-	 */
-	if (!err)
-		err = fh_update(resfhp);
 out:
 	dput(dchild);
 	return err;
@@ -1314,8 +1449,8 @@
  */
 __be32
 nfsd_create(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		char *fname, int flen, struct iattr *iap,
-		int type, dev_t rdev, struct svc_fh *resfhp)
+	    char *fname, int flen, struct nfsd_attrs *attrs,
+	    int type, dev_t rdev, struct svc_fh *resfhp)
 {
 	struct dentry	*dentry, *dchild = NULL;
 	__be32		err;
@@ -1334,11 +1469,13 @@
 	if (host_err)
 		return nfserrno(host_err);
 
-	fh_lock_nested(fhp, I_MUTEX_PARENT);
+	inode_lock_nested(dentry->d_inode, I_MUTEX_PARENT);
 	dchild = lookup_one_len(fname, dentry, flen);
 	host_err = PTR_ERR(dchild);
-	if (IS_ERR(dchild))
-		return nfserrno(host_err);
+	if (IS_ERR(dchild)) {
+		err = nfserrno(host_err);
+		goto out_unlock;
+	}
 	err = fh_compose(resfhp, fhp->fh_export, dchild, fhp);
 	/*
 	 * We unconditionally drop our ref to dchild as fh_compose will have
@@ -1346,178 +1483,14 @@
 	 */
 	dput(dchild);
 	if (err)
-		return err;
-	return nfsd_create_locked(rqstp, fhp, fname, flen, iap, type,
-					rdev, resfhp);
-}
-
-#ifdef CONFIG_NFSD_V3
-
-/*
- * NFSv3 and NFSv4 version of nfsd_create
- */
-__be32
-do_nfsd_create(struct svc_rqst *rqstp, struct svc_fh *fhp,
-		char *fname, int flen, struct iattr *iap,
-		struct svc_fh *resfhp, int createmode, u32 *verifier,
-	        bool *truncp, bool *created)
-{
-	struct dentry	*dentry, *dchild = NULL;
-	struct inode	*dirp;
-	__be32		err;
-	int		host_err;
-	__u32		v_mtime=0, v_atime=0;
-
-	err = nfserr_perm;
-	if (!flen)
-		goto out;
-	err = nfserr_exist;
-	if (isdotent(fname, flen))
-		goto out;
-	if (!(iap->ia_valid & ATTR_MODE))
-		iap->ia_mode = 0;
-	err = fh_verify(rqstp, fhp, S_IFDIR, NFSD_MAY_EXEC);
-	if (err)
-		goto out;
-
-	dentry = fhp->fh_dentry;
-	dirp = d_inode(dentry);
-
-	host_err = fh_want_write(fhp);
-	if (host_err)
-		goto out_nfserr;
-
-	fh_lock_nested(fhp, I_MUTEX_PARENT);
-
-	/*
-	 * Compose the response file handle.
-	 */
-	dchild = lookup_one_len(fname, dentry, flen);
-	host_err = PTR_ERR(dchild);
-	if (IS_ERR(dchild))
-		goto out_nfserr;
-
-	/* If file doesn't exist, check for permissions to create one */
-	if (d_really_is_negative(dchild)) {
-		err = fh_verify(rqstp, fhp, S_IFDIR, NFSD_MAY_CREATE);
-		if (err)
-			goto out;
-	}
-
-	err = fh_compose(resfhp, fhp->fh_export, dchild, fhp);
-	if (err)
-		goto out;
-
-	if (nfsd_create_is_exclusive(createmode)) {
-		/* solaris7 gets confused (bugid 4218508) if these have
-		 * the high bit set, so just clear the high bits. If this is
-		 * ever changed to use different attrs for storing the
-		 * verifier, then do_open_lookup() will also need to be fixed
-		 * accordingly.
-		 */
-		v_mtime = verifier[0]&0x7fffffff;
-		v_atime = verifier[1]&0x7fffffff;
-	}
-	
-	if (d_really_is_positive(dchild)) {
-		err = 0;
-
-		switch (createmode) {
-		case NFS3_CREATE_UNCHECKED:
-			if (! d_is_reg(dchild))
-				goto out;
-			else if (truncp) {
-				/* in nfsv4, we need to treat this case a little
-				 * differently.  we don't want to truncate the
-				 * file now; this would be wrong if the OPEN
-				 * fails for some other reason.  furthermore,
-				 * if the size is nonzero, we should ignore it
-				 * according to spec!
-				 */
-				*truncp = (iap->ia_valid & ATTR_SIZE) && !iap->ia_size;
-			}
-			else {
-				iap->ia_valid &= ATTR_SIZE;
-				goto set_attr;
-			}
-			break;
-		case NFS3_CREATE_EXCLUSIVE:
-			if (   d_inode(dchild)->i_mtime.tv_sec == v_mtime
-			    && d_inode(dchild)->i_atime.tv_sec == v_atime
-			    && d_inode(dchild)->i_size  == 0 ) {
-				if (created)
-					*created = true;
-				break;
-			}
-			fallthrough;
-		case NFS4_CREATE_EXCLUSIVE4_1:
-			if (   d_inode(dchild)->i_mtime.tv_sec == v_mtime
-			    && d_inode(dchild)->i_atime.tv_sec == v_atime
-			    && d_inode(dchild)->i_size  == 0 ) {
-				if (created)
-					*created = true;
-				goto set_attr;
-			}
-			fallthrough;
-		case NFS3_CREATE_GUARDED:
-			err = nfserr_exist;
-		}
-		fh_drop_write(fhp);
-		goto out;
-	}
-
-	if (!IS_POSIXACL(dirp))
-		iap->ia_mode &= ~current_umask();
-
-	host_err = vfs_create(&init_user_ns, dirp, dchild, iap->ia_mode, true);
-	if (host_err < 0) {
-		fh_drop_write(fhp);
-		goto out_nfserr;
-	}
-	if (created)
-		*created = true;
-
-	nfsd_check_ignore_resizing(iap);
-
-	if (nfsd_create_is_exclusive(createmode)) {
-		/* Cram the verifier into atime/mtime */
-		iap->ia_valid = ATTR_MTIME|ATTR_ATIME
-			| ATTR_MTIME_SET|ATTR_ATIME_SET;
-		/* XXX someone who knows this better please fix it for nsec */ 
-		iap->ia_mtime.tv_sec = v_mtime;
-		iap->ia_atime.tv_sec = v_atime;
-		iap->ia_mtime.tv_nsec = 0;
-		iap->ia_atime.tv_nsec = 0;
-	}
-
- set_attr:
-	err = nfsd_create_setattr(rqstp, resfhp, iap);
-
-	/*
-	 * nfsd_create_setattr already committed the child
-	 * (and possibly also the parent).
-	 */
-	if (!err)
-		err = nfserrno(commit_metadata(fhp));
-
-	/*
-	 * Update the filehandle to get the new inode info.
-	 */
-	if (!err)
-		err = fh_update(resfhp);
-
- out:
-	fh_unlock(fhp);
-	if (dchild && !IS_ERR(dchild))
-		dput(dchild);
-	fh_drop_write(fhp);
- 	return err;
- 
- out_nfserr:
-	err = nfserrno(host_err);
-	goto out;
+		goto out_unlock;
+	fh_fill_pre_attrs(fhp);
+	err = nfsd_create_locked(rqstp, fhp, attrs, type, rdev, resfhp);
+	fh_fill_post_attrs(fhp);
+out_unlock:
+	inode_unlock(dentry->d_inode);
+	return err;
 }
-#endif /* CONFIG_NFSD_V3 */
 
 /*
  * Read a symlink. On entry, *lenp must contain the maximum path length that
@@ -1557,15 +1530,25 @@
 	return 0;
 }
 
-/*
- * Create a symlink and look up its inode
+/**
+ * nfsd_symlink - Create a symlink and look up its inode
+ * @rqstp: RPC transaction being executed
+ * @fhp: NFS filehandle of parent directory
+ * @fname: filename of the new symlink
+ * @flen: length of @fname
+ * @path: content of the new symlink (NUL-terminated)
+ * @attrs: requested attributes of new object
+ * @resfhp: NFS filehandle of new object
+ *
  * N.B. After this call _both_ fhp and resfhp need an fh_put
+ *
+ * Returns nfs_ok on success, or an nfsstat in network byte order.
  */
 __be32
 nfsd_symlink(struct svc_rqst *rqstp, struct svc_fh *fhp,
-				char *fname, int flen,
-				char *path,
-				struct svc_fh *resfhp)
+	     char *fname, int flen,
+	     char *path, struct nfsd_attrs *attrs,
+	     struct svc_fh *resfhp)
 {
 	struct dentry	*dentry, *dnew;
 	__be32		err, cerr;
@@ -1583,33 +1566,35 @@
 		goto out;
 
 	host_err = fh_want_write(fhp);
-	if (host_err)
-		goto out_nfserr;
+	if (host_err) {
+		err = nfserrno(host_err);
+		goto out;
+	}
 
-	fh_lock(fhp);
 	dentry = fhp->fh_dentry;
+	inode_lock_nested(dentry->d_inode, I_MUTEX_PARENT);
 	dnew = lookup_one_len(fname, dentry, flen);
-	host_err = PTR_ERR(dnew);
-	if (IS_ERR(dnew))
-		goto out_nfserr;
-
+	if (IS_ERR(dnew)) {
+		err = nfserrno(PTR_ERR(dnew));
+		inode_unlock(dentry->d_inode);
+		goto out_drop_write;
+	}
+	fh_fill_pre_attrs(fhp);
 	host_err = vfs_symlink(&init_user_ns, d_inode(dentry), dnew, path);
 	err = nfserrno(host_err);
-	fh_unlock(fhp);
+	cerr = fh_compose(resfhp, fhp->fh_export, dnew, fhp);
+	if (!err)
+		nfsd_create_setattr(rqstp, fhp, resfhp, attrs);
+	fh_fill_post_attrs(fhp);
+	inode_unlock(dentry->d_inode);
 	if (!err)
 		err = nfserrno(commit_metadata(fhp));
-
-	fh_drop_write(fhp);
-
-	cerr = fh_compose(resfhp, fhp->fh_export, dnew, fhp);
 	dput(dnew);
 	if (err==0) err = cerr;
+out_drop_write:
+	fh_drop_write(fhp);
 out:
 	return err;
-
-out_nfserr:
-	err = nfserrno(host_err);
-	goto out;
 }
 
 /*
@@ -1647,22 +1632,25 @@
 		goto out;
 	}
 
-	fh_lock_nested(ffhp, I_MUTEX_PARENT);
 	ddir = ffhp->fh_dentry;
 	dirp = d_inode(ddir);
+	inode_lock_nested(dirp, I_MUTEX_PARENT);
 
 	dnew = lookup_one_len(name, ddir, len);
-	host_err = PTR_ERR(dnew);
-	if (IS_ERR(dnew))
-		goto out_nfserr;
+	if (IS_ERR(dnew)) {
+		err = nfserrno(PTR_ERR(dnew));
+		goto out_unlock;
+	}
 
 	dold = tfhp->fh_dentry;
 
 	err = nfserr_noent;
 	if (d_really_is_negative(dold))
 		goto out_dput;
+	fh_fill_pre_attrs(ffhp);
 	host_err = vfs_link(dold, &init_user_ns, dirp, dnew, NULL);
-	fh_unlock(ffhp);
+	fh_fill_post_attrs(ffhp);
+	inode_unlock(dirp);
 	if (!host_err) {
 		err = nfserrno(commit_metadata(ffhp));
 		if (!err)
@@ -1673,17 +1661,17 @@
 		else
 			err = nfserrno(host_err);
 	}
-out_dput:
 	dput(dnew);
-out_unlock:
-	fh_unlock(ffhp);
+out_drop_write:
 	fh_drop_write(tfhp);
 out:
 	return err;
 
-out_nfserr:
-	err = nfserrno(host_err);
-	goto out_unlock;
+out_dput:
+	dput(dnew);
+out_unlock:
+	inode_unlock(dirp);
+	goto out_drop_write;
 }
 
 static void
@@ -1737,6 +1725,12 @@
 	if (!flen || isdotent(fname, flen) || !tlen || isdotent(tname, tlen))
 		goto out;
 
+	err = (rqstp->rq_vers == 2) ? nfserr_acces : nfserr_xdev;
+	if (ffhp->fh_export->ex_path.mnt != tfhp->fh_export->ex_path.mnt)
+		goto out;
+	if (ffhp->fh_export->ex_path.dentry != tfhp->fh_export->ex_path.dentry)
+		goto out;
+
 retry:
 	host_err = fh_want_write(ffhp);
 	if (host_err) {
@@ -1744,12 +1738,9 @@
 		goto out;
 	}
 
-	/* cannot use fh_lock as we need deadlock protective ordering
-	 * so do it by hand */
 	trap = lock_rename(tdentry, fdentry);
-	ffhp->fh_locked = tfhp->fh_locked = true;
-	fill_pre_wcc(ffhp);
-	fill_pre_wcc(tfhp);
+	fh_fill_pre_attrs(ffhp);
+	fh_fill_pre_attrs(tfhp);
 
 	odentry = lookup_one_len(fname, fdentry, flen);
 	host_err = PTR_ERR(odentry);
@@ -1771,12 +1762,6 @@
 	if (ndentry == trap)
 		goto out_dput_new;
 
-	host_err = -EXDEV;
-	if (ffhp->fh_export->ex_path.mnt != tfhp->fh_export->ex_path.mnt)
-		goto out_dput_new;
-	if (ffhp->fh_export->ex_path.dentry != tfhp->fh_export->ex_path.dentry)
-		goto out_dput_new;
-
 	if ((ndentry->d_sb->s_export_op->flags & EXPORT_OP_CLOSE_BEFORE_UNLINK) &&
 	    nfsd_has_cached_files(ndentry)) {
 		close_cached = true;
@@ -1790,7 +1775,15 @@
 			.new_dir	= tdir,
 			.new_dentry	= ndentry,
 		};
-		host_err = vfs_rename(&rd);
+		int retries;
+
+		for (retries = 1;;) {
+			host_err = vfs_rename(&rd);
+			if (host_err != -EAGAIN || !retries--)
+				break;
+			if (!nfsd_wait_for_delegreturn(rqstp, d_inode(odentry)))
+				break;
+		}
 		if (!host_err) {
 			host_err = commit_metadata(tfhp);
 			if (!host_err)
@@ -1803,17 +1796,12 @@
 	dput(odentry);
  out_nfserr:
 	err = nfserrno(host_err);
-	/*
-	 * We cannot rely on fh_unlock on the two filehandles,
-	 * as that would do the wrong thing if the two directories
-	 * were the same, so again we do it by hand.
-	 */
+
 	if (!close_cached) {
-		fill_post_wcc(ffhp);
-		fill_post_wcc(tfhp);
+		fh_fill_post_attrs(ffhp);
+		fh_fill_post_attrs(tfhp);
 	}
 	unlock_rename(tdentry, fdentry);
-	ffhp->fh_locked = tfhp->fh_locked = false;
 	fh_drop_write(ffhp);
 
 	/*
@@ -1857,19 +1845,19 @@
 	if (host_err)
 		goto out_nfserr;
 
-	fh_lock_nested(fhp, I_MUTEX_PARENT);
 	dentry = fhp->fh_dentry;
 	dirp = d_inode(dentry);
+	inode_lock_nested(dirp, I_MUTEX_PARENT);
 
 	rdentry = lookup_one_len(fname, dentry, flen);
 	host_err = PTR_ERR(rdentry);
 	if (IS_ERR(rdentry))
-		goto out_drop_write;
+		goto out_unlock;
 
 	if (d_really_is_negative(rdentry)) {
 		dput(rdentry);
 		host_err = -ENOENT;
-		goto out_drop_write;
+		goto out_unlock;
 	}
 	rinode = d_inode(rdentry);
 	ihold(rinode);
@@ -1877,15 +1865,26 @@
 	if (!type)
 		type = d_inode(rdentry)->i_mode & S_IFMT;
 
+	fh_fill_pre_attrs(fhp);
 	if (type != S_IFDIR) {
+		int retries;
+
 		if (rdentry->d_sb->s_export_op->flags & EXPORT_OP_CLOSE_BEFORE_UNLINK)
 			nfsd_close_cached_files(rdentry);
-		host_err = vfs_unlink(&init_user_ns, dirp, rdentry, NULL);
+
+		for (retries = 1;;) {
+			host_err = vfs_unlink(&init_user_ns, dirp, rdentry, NULL);
+			if (host_err != -EAGAIN || !retries--)
+				break;
+			if (!nfsd_wait_for_delegreturn(rqstp, rinode))
+				break;
+		}
 	} else {
 		host_err = vfs_rmdir(&init_user_ns, dirp, rdentry);
 	}
+	fh_fill_post_attrs(fhp);
 
-	fh_unlock(fhp);
+	inode_unlock(dirp);
 	if (!host_err)
 		host_err = commit_metadata(fhp);
 	dput(rdentry);
@@ -1907,6 +1906,9 @@
 	}
 out:
 	return err;
+out_unlock:
+	inode_unlock(dirp);
+	goto out_drop_write;
 }
 
 /*
@@ -2260,13 +2262,16 @@
 	return err;
 }
 
-/*
- * Removexattr and setxattr need to call fh_lock to both lock the inode
- * and set the change attribute. Since the top-level vfs_removexattr
- * and vfs_setxattr calls already do their own inode_lock calls, call
- * the _locked variant. Pass in a NULL pointer for delegated_inode,
- * and let the client deal with NFS4ERR_DELAY (same as with e.g.
- * setattr and remove).
+/**
+ * nfsd_removexattr - Remove an extended attribute
+ * @rqstp: RPC transaction being executed
+ * @fhp: NFS filehandle of object with xattr to remove
+ * @name: name of xattr to remove (NUL-terminate)
+ *
+ * Pass in a NULL pointer for delegated_inode, and let the client deal
+ * with NFS4ERR_DELAY (same as with e.g. setattr and remove).
+ *
+ * Returns nfs_ok on success, or an nfsstat in network byte order.
  */
 __be32
 nfsd_removexattr(struct svc_rqst *rqstp, struct svc_fh *fhp, char *name)
@@ -2282,12 +2287,14 @@
 	if (ret)
 		return nfserrno(ret);
 
-	fh_lock(fhp);
+	inode_lock(fhp->fh_dentry->d_inode);
+	fh_fill_pre_attrs(fhp);
 
 	ret = __vfs_removexattr_locked(&init_user_ns, fhp->fh_dentry,
 				       name, NULL);
 
-	fh_unlock(fhp);
+	fh_fill_post_attrs(fhp);
+	inode_unlock(fhp->fh_dentry->d_inode);
 	fh_drop_write(fhp);
 
 	return nfsd_xattr_errno(ret);
@@ -2307,12 +2314,13 @@
 	ret = fh_want_write(fhp);
 	if (ret)
 		return nfserrno(ret);
-	fh_lock(fhp);
+	inode_lock(fhp->fh_dentry->d_inode);
+	fh_fill_pre_attrs(fhp);
 
 	ret = __vfs_setxattr_locked(&init_user_ns, fhp->fh_dentry, name, buf,
 				    len, flags, NULL);
-
-	fh_unlock(fhp);
+	fh_fill_post_attrs(fhp);
+	inode_unlock(fhp->fh_dentry->d_inode);
 	fh_drop_write(fhp);
 
 	return nfsd_xattr_errno(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/vfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/vfs.h
@@ -6,6 +6,8 @@
 #ifndef LINUX_NFSD_VFS_H
 #define LINUX_NFSD_VFS_H
 
+#include <linux/fs.h>
+#include <linux/posix_acl.h>
 #include "nfsfh.h"
 #include "nfsd.h"
 
@@ -42,6 +44,23 @@
 typedef int (*nfsd_filldir_t)(void *, const char *, int, loff_t, u64, unsigned);
 
 /* nfsd/vfs.c */
+struct nfsd_attrs {
+	struct iattr		*na_iattr;	/* input */
+	struct xdr_netobj	*na_seclabel;	/* input */
+	struct posix_acl	*na_pacl;	/* input */
+	struct posix_acl	*na_dpacl;	/* input */
+
+	int			na_labelerr;	/* output */
+	int			na_aclerr;	/* output */
+};
+
+static inline void nfsd_attrs_free(struct nfsd_attrs *attrs)
+{
+	posix_acl_release(attrs->na_pacl);
+	posix_acl_release(attrs->na_dpacl);
+}
+
+__be32		nfserrno (int errno);
 int		nfsd_cross_mnt(struct svc_rqst *rqstp, struct dentry **dpp,
 		                struct svc_export **expp);
 __be32		nfsd_lookup(struct svc_rqst *, struct svc_fh *,
@@ -50,32 +69,28 @@
 				const char *, unsigned int,
 				struct svc_export **, struct dentry **);
 __be32		nfsd_setattr(struct svc_rqst *, struct svc_fh *,
-				struct iattr *, int, time64_t);
+				struct nfsd_attrs *, int, time64_t);
 int nfsd_mountpoint(struct dentry *, struct svc_export *);
 #ifdef CONFIG_NFSD_V4
-__be32          nfsd4_set_nfs4_label(struct svc_rqst *, struct svc_fh *,
-		    struct xdr_netobj *);
 __be32		nfsd4_vfs_fallocate(struct svc_rqst *, struct svc_fh *,
 				    struct file *, loff_t, loff_t, int);
-__be32		nfsd4_clone_file_range(struct nfsd_file *nf_src, u64 src_pos,
+__be32		nfsd4_clone_file_range(struct svc_rqst *rqstp,
+				       struct nfsd_file *nf_src, u64 src_pos,
 				       struct nfsd_file *nf_dst, u64 dst_pos,
 				       u64 count, bool sync);
 #endif /* CONFIG_NFSD_V4 */
 __be32		nfsd_create_locked(struct svc_rqst *, struct svc_fh *,
-				char *name, int len, struct iattr *attrs,
-				int type, dev_t rdev, struct svc_fh *res);
+				struct nfsd_attrs *attrs, int type, dev_t rdev,
+				struct svc_fh *res);
 __be32		nfsd_create(struct svc_rqst *, struct svc_fh *,
-				char *name, int len, struct iattr *attrs,
+				char *name, int len, struct nfsd_attrs *attrs,
 				int type, dev_t rdev, struct svc_fh *res);
-#ifdef CONFIG_NFSD_V3
 __be32		nfsd_access(struct svc_rqst *, struct svc_fh *, u32 *, u32 *);
-__be32		do_nfsd_create(struct svc_rqst *, struct svc_fh *,
-				char *name, int len, struct iattr *attrs,
-				struct svc_fh *res, int createmode,
-				u32 *verifier, bool *truncp, bool *created);
-__be32		nfsd_commit(struct svc_rqst *, struct svc_fh *,
-				loff_t, unsigned long, __be32 *verf);
-#endif /* CONFIG_NFSD_V3 */
+__be32		nfsd_create_setattr(struct svc_rqst *rqstp, struct svc_fh *fhp,
+				struct svc_fh *resfhp, struct nfsd_attrs *iap);
+__be32		nfsd_commit(struct svc_rqst *rqst, struct svc_fh *fhp,
+				struct nfsd_file *nf, u64 offset, u32 count,
+				__be32 *verf);
 #ifdef CONFIG_NFSD_V4
 __be32		nfsd_getxattr(struct svc_rqst *rqstp, struct svc_fh *fhp,
 			    char *name, void **bufp, int *lenp);
@@ -89,7 +104,7 @@
 int 		nfsd_open_break_lease(struct inode *, int);
 __be32		nfsd_open(struct svc_rqst *, struct svc_fh *, umode_t,
 				int, struct file **);
-__be32		nfsd_open_verified(struct svc_rqst *, struct svc_fh *, umode_t,
+__be32		nfsd_open_verified(struct svc_rqst *, struct svc_fh *,
 				int, struct file **);
 __be32		nfsd_splice_read(struct svc_rqst *rqstp, struct svc_fh *fhp,
 				struct file *file, loff_t offset,
@@ -113,8 +128,9 @@
 __be32		nfsd_readlink(struct svc_rqst *, struct svc_fh *,
 				char *, int *);
 __be32		nfsd_symlink(struct svc_rqst *, struct svc_fh *,
-				char *name, int len, char *path,
-				struct svc_fh *res);
+			     char *name, int len, char *path,
+			     struct nfsd_attrs *attrs,
+			     struct svc_fh *res);
 __be32		nfsd_link(struct svc_rqst *, struct svc_fh *,
 				char *, int, struct svc_fh *);
 ssize_t		nfsd_copy_file_range(struct file *, u64,
@@ -160,10 +176,4 @@
 				    AT_STATX_SYNC_AS_STAT));
 }
 
-static inline int nfsd_create_is_exclusive(int createmode)
-{
-	return createmode == NFS3_CREATE_EXCLUSIVE
-	       || createmode == NFS4_CREATE_EXCLUSIVE4_1;
-}
-
 #endif /* LINUX_NFSD_VFS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/xdr.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/xdr.h
@@ -32,8 +32,8 @@
 struct nfsd_writeargs {
 	svc_fh			fh;
 	__u32			offset;
-	int			len;
-	struct kvec		first;
+	__u32			len;
+	struct xdr_buf		payload;
 };
 
 struct nfsd_createargs {
@@ -141,23 +141,24 @@
 #define NFS2_SVC_XDRSIZE	sizeof(union nfsd_xdrstore)
 
 
-int nfssvc_decode_fhandleargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_sattrargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_diropargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_readargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_writeargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_createargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_renameargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_linkargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_symlinkargs(struct svc_rqst *, __be32 *);
-int nfssvc_decode_readdirargs(struct svc_rqst *, __be32 *);
-int nfssvc_encode_statres(struct svc_rqst *, __be32 *);
-int nfssvc_encode_attrstatres(struct svc_rqst *, __be32 *);
-int nfssvc_encode_diropres(struct svc_rqst *, __be32 *);
-int nfssvc_encode_readlinkres(struct svc_rqst *, __be32 *);
-int nfssvc_encode_readres(struct svc_rqst *, __be32 *);
-int nfssvc_encode_statfsres(struct svc_rqst *, __be32 *);
-int nfssvc_encode_readdirres(struct svc_rqst *, __be32 *);
+bool nfssvc_decode_fhandleargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_sattrargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_diropargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_readargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_writeargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_createargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_renameargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_linkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_symlinkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_decode_readdirargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+
+bool nfssvc_encode_statres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_encode_attrstatres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_encode_diropres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_encode_readlinkres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_encode_readres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_encode_statfsres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfssvc_encode_readdirres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
 
 void nfssvc_encode_nfscookie(struct nfsd_readdirres *resp, u32 offset);
 int nfssvc_encode_entry(void *data, const char *name, int namlen,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/xdr3.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/xdr3.h
@@ -40,7 +40,7 @@
 	__u32			count;
 	int			stable;
 	__u32			len;
-	struct kvec		first;
+	struct xdr_buf		payload;
 };
 
 struct nfsd3_createargs {
@@ -265,36 +265,37 @@
 
 #define NFS3_SVC_XDRSIZE		sizeof(union nfsd3_xdrstore)
 
-int nfs3svc_decode_fhandleargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_sattrargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_diropargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_accessargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_readargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_writeargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_createargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_mkdirargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_mknodargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_renameargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_linkargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_symlinkargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_readdirargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_readdirplusargs(struct svc_rqst *, __be32 *);
-int nfs3svc_decode_commitargs(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_getattrres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_wccstat(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_lookupres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_accessres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_readlinkres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_readres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_writeres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_createres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_renameres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_linkres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_readdirres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_fsstatres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_fsinfores(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_pathconfres(struct svc_rqst *, __be32 *);
-int nfs3svc_encode_commitres(struct svc_rqst *, __be32 *);
+bool nfs3svc_decode_fhandleargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_sattrargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_diropargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_accessargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_readargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_writeargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_createargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_mkdirargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_mknodargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_renameargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_linkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_symlinkargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_readdirargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_readdirplusargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_decode_commitargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+
+bool nfs3svc_encode_getattrres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_wccstat(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_lookupres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_accessres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_readlinkres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_readres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_writeres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_createres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_renameres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_linkres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_readdirres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_fsstatres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_fsinfores(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_pathconfres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs3svc_encode_commitres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
 
 void nfs3svc_release_fhandle(struct svc_rqst *);
 void nfs3svc_release_fhandle2(struct svc_rqst *);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/xdr4.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/xdr4.h
@@ -273,11 +273,13 @@
 	bool		op_truncate;        /* used during processing */
 	bool		op_created;         /* used during processing */
 	struct nfs4_openowner *op_openowner; /* used during processing */
+	struct file	*op_filp;           /* used during processing */
 	struct nfs4_file *op_file;          /* used during processing */
 	struct nfs4_ol_stateid *op_stp;	    /* used during processing */
 	struct nfs4_clnt_odstate *op_odstate; /* used during processing */
 	struct nfs4_acl *op_acl;
 	struct xdr_netobj op_label;
+	struct svc_rqst *op_rqstp;
 };
 
 struct nfsd4_open_confirm {
@@ -301,9 +303,10 @@
 	u32			rd_length;          /* request */
 	int			rd_vlen;
 	struct nfsd_file	*rd_nf;
-	
+
 	struct svc_rqst		*rd_rqstp;          /* response */
-	struct svc_fh		*rd_fhp;             /* response */
+	struct svc_fh		*rd_fhp;            /* response */
+	u32			rd_eof;             /* response */
 };
 
 struct nfsd4_readdir {
@@ -531,6 +534,13 @@
 	stateid_t		cb_stateid;
 };
 
+struct nfsd4_cb_offload {
+	struct nfsd4_callback	co_cb;
+	struct nfsd42_write_res	co_res;
+	__be32			co_nfserr;
+	struct knfsd_fh		co_fh;
+};
+
 struct nfsd4_copy {
 	/* request */
 	stateid_t		cp_src_stateid;
@@ -538,18 +548,16 @@
 	u64			cp_src_pos;
 	u64			cp_dst_pos;
 	u64			cp_count;
-	struct nl4_server	cp_src;
-	bool			cp_intra;
+	struct nl4_server	*cp_src;
 
-	/* both */
-	u32			cp_synchronous;
+	unsigned long		cp_flags;
+#define NFSD4_COPY_F_STOPPED		(0)
+#define NFSD4_COPY_F_INTRA		(1)
+#define NFSD4_COPY_F_SYNCHRONOUS	(2)
+#define NFSD4_COPY_F_COMMITTED		(3)
 
 	/* response */
 	struct nfsd42_write_res	cp_res;
-
-	/* for cb_offload */
-	struct nfsd4_callback	cp_cb;
-	__be32			nfserr;
 	struct knfsd_fh		fh;
 
 	struct nfs4_client      *cp_clp;
@@ -562,14 +570,36 @@
 	struct list_head	copies;
 	struct task_struct	*copy_task;
 	refcount_t		refcount;
-	bool			stopped;
 
-	struct vfsmount		*ss_mnt;
+	struct nfsd4_ssc_umount_item *ss_nsui;
 	struct nfs_fh		c_fh;
 	nfs4_stateid		stateid;
-	bool			committed;
+	struct nfsd_net		*cp_nn;
 };
 
+static inline void nfsd4_copy_set_sync(struct nfsd4_copy *copy, bool sync)
+{
+	if (sync)
+		set_bit(NFSD4_COPY_F_SYNCHRONOUS, &copy->cp_flags);
+	else
+		clear_bit(NFSD4_COPY_F_SYNCHRONOUS, &copy->cp_flags);
+}
+
+static inline bool nfsd4_copy_is_sync(const struct nfsd4_copy *copy)
+{
+	return test_bit(NFSD4_COPY_F_SYNCHRONOUS, &copy->cp_flags);
+}
+
+static inline bool nfsd4_copy_is_async(const struct nfsd4_copy *copy)
+{
+	return !test_bit(NFSD4_COPY_F_SYNCHRONOUS, &copy->cp_flags);
+}
+
+static inline bool nfsd4_ssc_is_inter(const struct nfsd4_copy *copy)
+{
+	return !test_bit(NFSD4_COPY_F_INTRA, &copy->cp_flags);
+}
+
 struct nfsd4_seek {
 	/* request */
 	stateid_t	seek_stateid;
@@ -593,19 +623,20 @@
 struct nfsd4_copy_notify {
 	/* request */
 	stateid_t		cpn_src_stateid;
-	struct nl4_server	cpn_dst;
+	struct nl4_server	*cpn_dst;
 
 	/* response */
 	stateid_t		cpn_cnr_stateid;
 	u64			cpn_sec;
 	u32			cpn_nsec;
-	struct nl4_server	cpn_src;
+	struct nl4_server	*cpn_src;
 };
 
 struct nfsd4_op {
 	u32					opnum;
-	const struct nfsd4_operation *		opdesc;
 	__be32					status;
+	const struct nfsd4_operation		*opdesc;
+	struct nfs4_replay			*replay;
 	union nfsd4_op_u {
 		struct nfsd4_access		access;
 		struct nfsd4_close		close;
@@ -669,7 +700,6 @@
 		struct nfsd4_listxattrs		listxattrs;
 		struct nfsd4_removexattr	removexattr;
 	} u;
-	struct nfs4_replay *			replay;
 };
 
 bool nfsd4_cache_this_op(struct nfsd4_op *);
@@ -688,13 +718,13 @@
 	struct svcxdr_tmpbuf		*to_free;
 	struct svc_rqst			*rqstp;
 
-	u32				taglen;
 	char *				tag;
+	u32				taglen;
 	u32				minorversion;
+	u32				client_opcnt;
 	u32				opcnt;
 	struct nfsd4_op			*ops;
 	struct nfsd4_op			iops[8];
-	int				cachetype;
 };
 
 struct nfsd4_compoundres {
@@ -702,10 +732,11 @@
 	struct xdr_stream		*xdr;
 	struct svc_rqst *		rqstp;
 
-	u32				taglen;
+	__be32				*statusp;
 	char *				tag;
+	u32				taglen;
 	u32				opcnt;
-	__be32 *			tagp; /* tag, opcount encode location */
+
 	struct nfsd4_compound_state	cstate;
 };
 
@@ -756,8 +787,8 @@
 
 
 bool nfsd4_mach_creds_match(struct nfs4_client *cl, struct svc_rqst *rqstp);
-int nfs4svc_decode_compoundargs(struct svc_rqst *, __be32 *);
-int nfs4svc_encode_compoundres(struct svc_rqst *, __be32 *);
+bool nfs4svc_decode_compoundargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool nfs4svc_encode_compoundres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
 __be32 nfsd4_check_resp_size(struct nfsd4_compoundres *, u32);
 void nfsd4_encode_operation(struct nfsd4_compoundres *, struct nfsd4_op *);
 void nfsd4_encode_replay(struct xdr_stream *xdr, struct nfsd4_op *op);
@@ -858,12 +889,18 @@
 	u32 op_flags;
 	char *op_name;
 	/* Try to get response size before operation */
-	u32 (*op_rsize_bop)(struct svc_rqst *, struct nfsd4_op *);
+	u32 (*op_rsize_bop)(const struct svc_rqst *rqstp,
+			const struct nfsd4_op *op);
 	void (*op_get_currentstateid)(struct nfsd4_compound_state *,
 			union nfsd4_op_u *);
 	void (*op_set_currentstateid)(struct nfsd4_compound_state *,
 			union nfsd4_op_u *);
 };
 
+struct nfsd4_cb_recall_any {
+	struct nfsd4_callback	ra_cb;
+	u32			ra_keep;
+	u32			ra_bmval[1];
+};
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nfsd/xdr4cb.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nfsd/xdr4cb.h
@@ -48,3 +48,9 @@
 #define NFS4_dec_cb_offload_sz		(cb_compound_dec_hdr_sz  +      \
 					cb_sequence_dec_sz +            \
 					op_dec_sz)
+#define NFS4_enc_cb_recall_any_sz	(cb_compound_enc_hdr_sz +       \
+					cb_sequence_enc_sz +            \
+					1 + 1 + 1)
+#define NFS4_dec_cb_recall_any_sz	(cb_compound_dec_hdr_sz  +      \
+					cb_sequence_dec_sz +            \
+					op_dec_sz)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/alloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/alloc.c
@@ -205,7 +205,8 @@
 	int ret;
 
 	spin_lock(lock);
-	if (prev->bh && blkoff == prev->blkoff) {
+	if (prev->bh && blkoff == prev->blkoff &&
+	    likely(buffer_uptodate(prev->bh))) {
 		get_bh(prev->bh);
 		*bhp = prev->bh;
 		spin_unlock(lock);
@@ -376,11 +377,12 @@
  * @target: offset number of an entry in the group (start point)
  * @bsize: size in bits
  * @lock: spin lock protecting @bitmap
+ * @wrap: whether to wrap around
  */
 static int nilfs_palloc_find_available_slot(unsigned char *bitmap,
 					    unsigned long target,
 					    unsigned int bsize,
-					    spinlock_t *lock)
+					    spinlock_t *lock, bool wrap)
 {
 	int pos, end = bsize;
 
@@ -396,6 +398,8 @@
 
 		end = target;
 	}
+	if (!wrap)
+		return -ENOSPC;
 
 	/* wrap around */
 	for (pos = 0; pos < end; pos++) {
@@ -494,9 +498,10 @@
  * nilfs_palloc_prepare_alloc_entry - prepare to allocate a persistent object
  * @inode: inode of metadata file using this allocator
  * @req: nilfs_palloc_req structure exchanged for the allocation
+ * @wrap: whether to wrap around
  */
 int nilfs_palloc_prepare_alloc_entry(struct inode *inode,
-				     struct nilfs_palloc_req *req)
+				     struct nilfs_palloc_req *req, bool wrap)
 {
 	struct buffer_head *desc_bh, *bitmap_bh;
 	struct nilfs_palloc_group_desc *desc;
@@ -515,7 +520,7 @@
 	entries_per_group = nilfs_palloc_entries_per_group(inode);
 
 	for (i = 0; i < ngroups; i += n) {
-		if (group >= ngroups) {
+		if (group >= ngroups && wrap) {
 			/* wrap around */
 			group = 0;
 			maxgroup = nilfs_palloc_group(inode, req->pr_entry_nr,
@@ -540,7 +545,13 @@
 				bitmap = bitmap_kaddr + bh_offset(bitmap_bh);
 				pos = nilfs_palloc_find_available_slot(
 					bitmap, group_offset,
-					entries_per_group, lock);
+					entries_per_group, lock, wrap);
+				/*
+				 * Since the search for a free slot in the
+				 * second and subsequent bitmap blocks always
+				 * starts from the beginning, the wrap flag
+				 * only has an effect on the first search.
+				 */
 				if (pos >= 0) {
 					/* found a free entry */
 					nilfs_palloc_group_desc_add_entries(
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/alloc.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/alloc.h
@@ -50,8 +50,8 @@
 	struct buffer_head *pr_entry_bh;
 };
 
-int nilfs_palloc_prepare_alloc_entry(struct inode *,
-				     struct nilfs_palloc_req *);
+int nilfs_palloc_prepare_alloc_entry(struct inode *inode,
+				     struct nilfs_palloc_req *req, bool wrap);
 void nilfs_palloc_commit_alloc_entry(struct inode *,
 				     struct nilfs_palloc_req *);
 void nilfs_palloc_abort_alloc_entry(struct inode *, struct nilfs_palloc_req *);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/bmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/bmap.c
@@ -67,20 +67,28 @@
 
 	down_read(&bmap->b_sem);
 	ret = bmap->b_ops->bop_lookup(bmap, key, level, ptrp);
-	if (ret < 0) {
-		ret = nilfs_bmap_convert_error(bmap, __func__, ret);
+	if (ret < 0)
 		goto out;
-	}
+
 	if (NILFS_BMAP_USE_VBN(bmap)) {
 		ret = nilfs_dat_translate(nilfs_bmap_get_dat(bmap), *ptrp,
 					  &blocknr);
 		if (!ret)
 			*ptrp = blocknr;
+		else if (ret == -ENOENT) {
+			/*
+			 * If there was no valid entry in DAT for the block
+			 * address obtained by b_ops->bop_lookup, then pass
+			 * internal code -EINVAL to nilfs_bmap_convert_error
+			 * to treat it as metadata corruption.
+			 */
+			ret = -EINVAL;
+		}
 	}
 
  out:
 	up_read(&bmap->b_sem);
-	return ret;
+	return nilfs_bmap_convert_error(bmap, __func__, ret);
 }
 
 int nilfs_bmap_lookup_contig(struct nilfs_bmap *bmap, __u64 key, __u64 *ptrp,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/btnode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/btnode.c
@@ -20,6 +20,23 @@
 #include "page.h"
 #include "btnode.h"
 
+
+/**
+ * nilfs_init_btnc_inode - initialize B-tree node cache inode
+ * @btnc_inode: inode to be initialized
+ *
+ * nilfs_init_btnc_inode() sets up an inode for B-tree node cache.
+ */
+void nilfs_init_btnc_inode(struct inode *btnc_inode)
+{
+	struct nilfs_inode_info *ii = NILFS_I(btnc_inode);
+
+	btnc_inode->i_mode = S_IFREG;
+	ii->i_flags = 0;
+	memset(&ii->i_bmap_data, 0, sizeof(struct nilfs_bmap));
+	mapping_set_gfp_mask(btnc_inode->i_mapping, GFP_NOFS);
+}
+
 void nilfs_btnode_cache_clear(struct address_space *btnc)
 {
 	invalidate_mapping_pages(btnc, 0, -1);
@@ -29,20 +46,28 @@
 struct buffer_head *
 nilfs_btnode_create_block(struct address_space *btnc, __u64 blocknr)
 {
-	struct inode *inode = NILFS_BTNC_I(btnc);
+	struct inode *inode = btnc->host;
 	struct buffer_head *bh;
 
 	bh = nilfs_grab_buffer(inode, btnc, blocknr, BIT(BH_NILFS_Node));
 	if (unlikely(!bh))
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	if (unlikely(buffer_mapped(bh) || buffer_uptodate(bh) ||
 		     buffer_dirty(bh))) {
-		brelse(bh);
-		BUG();
+		/*
+		 * The block buffer at the specified new address was already
+		 * in use.  This can happen if it is a virtual block number
+		 * and has been reallocated due to corruption of the bitmap
+		 * used to manage its allocation state (if not, the buffer
+		 * clearing of an abandoned b-tree node is missing somewhere).
+		 */
+		nilfs_error(inode->i_sb,
+			    "state inconsistency probably due to duplicate use of b-tree node block address %llu (ino=%lu)",
+			    (unsigned long long)blocknr, inode->i_ino);
+		goto failed;
 	}
 	memset(bh->b_data, 0, i_blocksize(inode));
-	bh->b_bdev = inode->i_sb->s_bdev;
 	bh->b_blocknr = blocknr;
 	set_buffer_mapped(bh);
 	set_buffer_uptodate(bh);
@@ -50,6 +75,12 @@
 	unlock_page(bh->b_page);
 	put_page(bh->b_page);
 	return bh;
+
+failed:
+	unlock_page(bh->b_page);
+	put_page(bh->b_page);
+	brelse(bh);
+	return ERR_PTR(-EIO);
 }
 
 int nilfs_btnode_submit_block(struct address_space *btnc, __u64 blocknr,
@@ -57,7 +88,7 @@
 			      struct buffer_head **pbh, sector_t *submit_ptr)
 {
 	struct buffer_head *bh;
-	struct inode *inode = NILFS_BTNC_I(btnc);
+	struct inode *inode = btnc->host;
 	struct page *page;
 	int err;
 
@@ -101,7 +132,6 @@
 		goto found;
 	}
 	set_buffer_mapped(bh);
-	bh->b_bdev = inode->i_sb->s_bdev;
 	bh->b_blocknr = pblocknr; /* set block address for read */
 	bh->b_end_io = end_buffer_read_sync;
 	get_bh(bh);
@@ -157,7 +187,7 @@
 				    struct nilfs_btnode_chkey_ctxt *ctxt)
 {
 	struct buffer_head *obh, *nbh;
-	struct inode *inode = NILFS_BTNC_I(btnc);
+	struct inode *inode = btnc->host;
 	__u64 oldkey = ctxt->oldkey, newkey = ctxt->newkey;
 	int err;
 
@@ -200,8 +230,8 @@
 	}
 
 	nbh = nilfs_btnode_create_block(btnc, newkey);
-	if (!nbh)
-		return -ENOMEM;
+	if (IS_ERR(nbh))
+		return PTR_ERR(nbh);
 
 	BUG_ON(nbh == obh);
 	ctxt->newbh = nbh;
@@ -268,6 +298,14 @@
 	if (nbh == NULL) {	/* blocksize == pagesize */
 		xa_erase_irq(&btnc->i_pages, newkey);
 		unlock_page(ctxt->bh->b_page);
-	} else
-		brelse(nbh);
+	} else {
+		/*
+		 * When canceling a buffer that a prepare operation has
+		 * allocated to copy a node block to another location, use
+		 * nilfs_btnode_delete() to initialize and release the buffer
+		 * so that the buffer flags will not be in an inconsistent
+		 * state when it is reallocated.
+		 */
+		nilfs_btnode_delete(nbh);
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/btnode.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/btnode.h
@@ -30,6 +30,7 @@
 	struct buffer_head *newbh;
 };
 
+void nilfs_init_btnc_inode(struct inode *btnc_inode);
 void nilfs_btnode_cache_clear(struct address_space *);
 struct buffer_head *nilfs_btnode_create_block(struct address_space *btnc,
 					      __u64 blocknr);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/btree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/btree.c
@@ -58,12 +58,13 @@
 static int nilfs_btree_get_new_block(const struct nilfs_bmap *btree,
 				     __u64 ptr, struct buffer_head **bhp)
 {
-	struct address_space *btnc = &NILFS_BMAP_I(btree)->i_btnode_cache;
+	struct inode *btnc_inode = NILFS_BMAP_I(btree)->i_assoc_inode;
+	struct address_space *btnc = btnc_inode->i_mapping;
 	struct buffer_head *bh;
 
 	bh = nilfs_btnode_create_block(btnc, ptr);
-	if (!bh)
-		return -ENOMEM;
+	if (IS_ERR(bh))
+		return PTR_ERR(bh);
 
 	set_buffer_nilfs_volatile(bh);
 	*bhp = bh;
@@ -349,7 +350,7 @@
 	if (unlikely(level < NILFS_BTREE_LEVEL_NODE_MIN ||
 		     level >= NILFS_BTREE_LEVEL_MAX ||
 		     (flags & NILFS_BTREE_NODE_ROOT) ||
-		     nchildren < 0 ||
+		     nchildren <= 0 ||
 		     nchildren > NILFS_BTREE_NODE_NCHILDREN_MAX(size))) {
 		nilfs_crit(inode->i_sb,
 			   "bad btree node (ino=%lu, blocknr=%llu): level = %d, flags = 0x%x, nchildren = %d",
@@ -380,7 +381,8 @@
 	if (unlikely(level < NILFS_BTREE_LEVEL_NODE_MIN ||
 		     level >= NILFS_BTREE_LEVEL_MAX ||
 		     nchildren < 0 ||
-		     nchildren > NILFS_BTREE_ROOT_NCHILDREN_MAX)) {
+		     nchildren > NILFS_BTREE_ROOT_NCHILDREN_MAX ||
+		     (nchildren == 0 && level > NILFS_BTREE_LEVEL_NODE_MIN))) {
 		nilfs_crit(inode->i_sb,
 			   "bad btree root (ino=%lu): level = %d, flags = 0x%x, nchildren = %d",
 			   inode->i_ino, level, flags, nchildren);
@@ -470,7 +472,8 @@
 				   struct buffer_head **bhp,
 				   const struct nilfs_btree_readahead_info *ra)
 {
-	struct address_space *btnc = &NILFS_BMAP_I(btree)->i_btnode_cache;
+	struct inode *btnc_inode = NILFS_BMAP_I(btree)->i_assoc_inode;
+	struct address_space *btnc = btnc_inode->i_mapping;
 	struct buffer_head *bh, *ra_bh;
 	sector_t submit_ptr = 0;
 	int ret;
@@ -478,9 +481,18 @@
 	ret = nilfs_btnode_submit_block(btnc, ptr, 0, REQ_OP_READ, 0, &bh,
 					&submit_ptr);
 	if (ret) {
-		if (ret != -EEXIST)
-			return ret;
-		goto out_check;
+		if (likely(ret == -EEXIST))
+			goto out_check;
+		if (ret == -ENOENT) {
+			/*
+			 * Block address translation failed due to invalid
+			 * value of 'ptr'.  In this case, return internal code
+			 * -EINVAL (broken bmap) to notify bmap layer of fatal
+			 * metadata corruption.
+			 */
+			ret = -EINVAL;
+		}
+		return ret;
 	}
 
 	if (ra) {
@@ -713,7 +725,7 @@
 		dat = nilfs_bmap_get_dat(btree);
 		ret = nilfs_dat_translate(dat, ptr, &blocknr);
 		if (ret < 0)
-			goto out;
+			goto dat_error;
 		ptr = blocknr;
 	}
 	cnt = 1;
@@ -732,7 +744,7 @@
 			if (dat) {
 				ret = nilfs_dat_translate(dat, ptr2, &blocknr);
 				if (ret < 0)
-					goto out;
+					goto dat_error;
 				ptr2 = blocknr;
 			}
 			if (ptr2 != ptr + cnt || ++cnt == maxblocks)
@@ -770,6 +782,11 @@
  out:
 	nilfs_btree_free_path(path);
 	return ret;
+
+ dat_error:
+	if (ret == -ENOENT)
+		ret = -EINVAL;  /* Notify bmap layer of metadata corruption */
+	goto out;
 }
 
 static void nilfs_btree_promote_key(struct nilfs_bmap *btree,
@@ -1642,13 +1659,16 @@
 	int nchildren, ret;
 
 	root = nilfs_btree_get_root(btree);
+	nchildren = nilfs_btree_node_get_nchildren(root);
+	if (unlikely(nchildren == 0))
+		return 0;
+
 	switch (nilfs_btree_height(btree)) {
 	case 2:
 		bh = NULL;
 		node = root;
 		break;
 	case 3:
-		nchildren = nilfs_btree_node_get_nchildren(root);
 		if (nchildren > 1)
 			return 0;
 		ptr = nilfs_btree_node_get_ptr(root, nchildren - 1,
@@ -1657,12 +1677,12 @@
 		if (ret < 0)
 			return ret;
 		node = (struct nilfs_btree_node *)bh->b_data;
+		nchildren = nilfs_btree_node_get_nchildren(node);
 		break;
 	default:
 		return 0;
 	}
 
-	nchildren = nilfs_btree_node_get_nchildren(node);
 	maxkey = nilfs_btree_node_get_key(node, nchildren - 1);
 	nextmaxkey = (nchildren > 1) ?
 		nilfs_btree_node_get_key(node, nchildren - 2) : 0;
@@ -1741,6 +1761,10 @@
 		dat = nilfs_bmap_get_dat(btree);
 	}
 
+	ret = nilfs_attach_btree_node_cache(&NILFS_BMAP_I(btree)->vfs_inode);
+	if (ret < 0)
+		return ret;
+
 	ret = nilfs_bmap_prepare_alloc_ptr(btree, dreq, dat);
 	if (ret < 0)
 		return ret;
@@ -1913,7 +1937,7 @@
 		path[level].bp_ctxt.newkey = path[level].bp_newreq.bpr_ptr;
 		path[level].bp_ctxt.bh = path[level].bp_bh;
 		ret = nilfs_btnode_prepare_change_key(
-			&NILFS_BMAP_I(btree)->i_btnode_cache,
+			NILFS_BMAP_I(btree)->i_assoc_inode->i_mapping,
 			&path[level].bp_ctxt);
 		if (ret < 0) {
 			nilfs_dat_abort_update(dat,
@@ -1939,7 +1963,7 @@
 
 	if (buffer_nilfs_node(path[level].bp_bh)) {
 		nilfs_btnode_commit_change_key(
-			&NILFS_BMAP_I(btree)->i_btnode_cache,
+			NILFS_BMAP_I(btree)->i_assoc_inode->i_mapping,
 			&path[level].bp_ctxt);
 		path[level].bp_bh = path[level].bp_ctxt.bh;
 	}
@@ -1958,7 +1982,7 @@
 			       &path[level].bp_newreq.bpr_req);
 	if (buffer_nilfs_node(path[level].bp_bh))
 		nilfs_btnode_abort_change_key(
-			&NILFS_BMAP_I(btree)->i_btnode_cache,
+			NILFS_BMAP_I(btree)->i_assoc_inode->i_mapping,
 			&path[level].bp_ctxt);
 }
 
@@ -2134,7 +2158,8 @@
 static void nilfs_btree_lookup_dirty_buffers(struct nilfs_bmap *btree,
 					     struct list_head *listp)
 {
-	struct address_space *btcache = &NILFS_BMAP_I(btree)->i_btnode_cache;
+	struct inode *btnc_inode = NILFS_BMAP_I(btree)->i_assoc_inode;
+	struct address_space *btcache = btnc_inode->i_mapping;
 	struct list_head lists[NILFS_BTREE_LEVEL_MAX];
 	struct pagevec pvec;
 	struct buffer_head *bh, *head;
@@ -2188,12 +2213,12 @@
 		path[level].bp_ctxt.newkey = blocknr;
 		path[level].bp_ctxt.bh = *bh;
 		ret = nilfs_btnode_prepare_change_key(
-			&NILFS_BMAP_I(btree)->i_btnode_cache,
+			NILFS_BMAP_I(btree)->i_assoc_inode->i_mapping,
 			&path[level].bp_ctxt);
 		if (ret < 0)
 			return ret;
 		nilfs_btnode_commit_change_key(
-			&NILFS_BMAP_I(btree)->i_btnode_cache,
+			NILFS_BMAP_I(btree)->i_assoc_inode->i_mapping,
 			&path[level].bp_ctxt);
 		*bh = path[level].bp_ctxt.bh;
 	}
@@ -2398,6 +2423,10 @@
 
 	if (nilfs_btree_root_broken(nilfs_btree_get_root(bmap), bmap->b_inode))
 		ret = -EIO;
+	else
+		ret = nilfs_attach_btree_node_cache(
+			&NILFS_BMAP_I(bmap)->vfs_inode);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/dat.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/dat.c
@@ -40,8 +40,21 @@
 static int nilfs_dat_prepare_entry(struct inode *dat,
 				   struct nilfs_palloc_req *req, int create)
 {
-	return nilfs_palloc_get_entry_block(dat, req->pr_entry_nr,
-					    create, &req->pr_entry_bh);
+	int ret;
+
+	ret = nilfs_palloc_get_entry_block(dat, req->pr_entry_nr,
+					   create, &req->pr_entry_bh);
+	if (unlikely(ret == -ENOENT)) {
+		nilfs_err(dat->i_sb,
+			  "DAT doesn't have a block to manage vblocknr = %llu",
+			  (unsigned long long)req->pr_entry_nr);
+		/*
+		 * Return internal code -EINVAL to notify bmap layer of
+		 * metadata corruption.
+		 */
+		ret = -EINVAL;
+	}
+	return ret;
 }
 
 static void nilfs_dat_commit_entry(struct inode *dat,
@@ -62,7 +75,7 @@
 {
 	int ret;
 
-	ret = nilfs_palloc_prepare_alloc_entry(dat, req);
+	ret = nilfs_palloc_prepare_alloc_entry(dat, req, true);
 	if (ret < 0)
 		return ret;
 
@@ -111,16 +124,19 @@
 	kunmap_atomic(kaddr);
 
 	nilfs_dat_commit_entry(dat, req);
+
+	if (unlikely(req->pr_desc_bh == NULL || req->pr_bitmap_bh == NULL)) {
+		nilfs_error(dat->i_sb,
+			    "state inconsistency probably due to duplicate use of vblocknr = %llu",
+			    (unsigned long long)req->pr_entry_nr);
+		return;
+	}
 	nilfs_palloc_commit_free_entry(dat, req);
 }
 
 int nilfs_dat_prepare_start(struct inode *dat, struct nilfs_palloc_req *req)
 {
-	int ret;
-
-	ret = nilfs_dat_prepare_entry(dat, req, 0);
-	WARN_ON(ret == -ENOENT);
-	return ret;
+	return nilfs_dat_prepare_entry(dat, req, 0);
 }
 
 void nilfs_dat_commit_start(struct inode *dat, struct nilfs_palloc_req *req,
@@ -147,10 +163,8 @@
 	int ret;
 
 	ret = nilfs_dat_prepare_entry(dat, req, 0);
-	if (ret < 0) {
-		WARN_ON(ret == -ENOENT);
+	if (ret < 0)
 		return ret;
-	}
 
 	kaddr = kmap_atomic(req->pr_entry_bh->b_page);
 	entry = nilfs_palloc_block_get_entry(dat, req->pr_entry_nr,
@@ -497,7 +511,9 @@
 	di = NILFS_DAT_I(dat);
 	lockdep_set_class(&di->mi.mi_sem, &dat_lock_key);
 	nilfs_palloc_setup_cache(dat, &di->palloc_cache);
-	nilfs_mdt_setup_shadow_map(dat, &di->shadow);
+	err = nilfs_mdt_setup_shadow_map(dat, &di->shadow);
+	if (err)
+		goto failed;
 
 	err = nilfs_read_inode_common(dat, raw_inode);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/dir.c
@@ -64,19 +64,13 @@
 	return inode->i_sb->s_blocksize;
 }
 
-static inline void nilfs_put_page(struct page *page)
-{
-	kunmap(page);
-	put_page(page);
-}
-
 /*
  * Return the offset into page `page_nr' of the last valid
  * byte in that page, plus one.
  */
 static unsigned int nilfs_last_byte(struct inode *inode, unsigned long page_nr)
 {
-	unsigned int last_byte = inode->i_size;
+	u64 last_byte = inode->i_size;
 
 	last_byte -= page_nr << PAGE_SHIFT;
 	if (last_byte > PAGE_SIZE)
@@ -143,6 +137,9 @@
 			goto Enamelen;
 		if (((offs + rec_len - 1) ^ offs) & ~(chunk_size-1))
 			goto Espan;
+		if (unlikely(p->inode &&
+			     NILFS_PRIVATE_INODE(le64_to_cpu(p->inode))))
+			goto Einumber;
 	}
 	if (offs != limit)
 		goto Eend;
@@ -168,6 +165,9 @@
 	goto bad_entry;
 Espan:
 	error = "directory entry across blocks";
+	goto bad_entry;
+Einumber:
+	error = "disallowed inode number";
 bad_entry:
 	nilfs_error(sb,
 		    "bad entry in directory #%lu: %s - offset=%lu, inode=%lu, rec_len=%d, name_len=%d",
@@ -186,19 +186,24 @@
 	return false;
 }
 
-static struct page *nilfs_get_page(struct inode *dir, unsigned long n)
+static void *nilfs_get_page(struct inode *dir, unsigned long n,
+		struct page **pagep)
 {
 	struct address_space *mapping = dir->i_mapping;
 	struct page *page = read_mapping_page(mapping, n, NULL);
+	void *kaddr;
 
-	if (!IS_ERR(page)) {
-		kmap(page);
-		if (unlikely(!PageChecked(page))) {
-			if (PageError(page) || !nilfs_check_page(page))
-				goto fail;
-		}
+	if (IS_ERR(page))
+		return page;
+
+	kaddr = kmap(page);
+	if (unlikely(!PageChecked(page))) {
+		if (!nilfs_check_page(page))
+			goto fail;
 	}
-	return page;
+
+	*pagep = page;
+	return kaddr;
 
 fail:
 	nilfs_put_page(page);
@@ -243,7 +248,7 @@
 
 #define S_SHIFT 12
 static unsigned char
-nilfs_type_by_mode[S_IFMT >> S_SHIFT] = {
+nilfs_type_by_mode[(S_IFMT >> S_SHIFT) + 1] = {
 	[S_IFREG >> S_SHIFT]	= NILFS_FT_REG_FILE,
 	[S_IFDIR >> S_SHIFT]	= NILFS_FT_DIR,
 	[S_IFCHR >> S_SHIFT]	= NILFS_FT_CHRDEV,
@@ -275,14 +280,14 @@
 	for ( ; n < npages; n++, offset = 0) {
 		char *kaddr, *limit;
 		struct nilfs_dir_entry *de;
-		struct page *page = nilfs_get_page(inode, n);
+		struct page *page;
 
-		if (IS_ERR(page)) {
+		kaddr = nilfs_get_page(inode, n, &page);
+		if (IS_ERR(kaddr)) {
 			nilfs_error(sb, "bad page in #%lu", inode->i_ino);
 			ctx->pos += PAGE_SIZE - offset;
 			return -EIO;
 		}
-		kaddr = page_address(page);
 		de = (struct nilfs_dir_entry *)(kaddr + offset);
 		limit = kaddr + nilfs_last_byte(inode, n) -
 			NILFS_DIR_REC_LEN(1);
@@ -320,6 +325,8 @@
  * returns the page in which the entry was found, and the entry itself
  * (as a parameter - res_dir). Page is returned mapped and unlocked.
  * Entry is guaranteed to be valid.
+ *
+ * On failure, returns an error pointer and the caller should ignore res_page.
  */
 struct nilfs_dir_entry *
 nilfs_find_entry(struct inode *dir, const struct qstr *qstr,
@@ -345,26 +352,26 @@
 		start = 0;
 	n = start;
 	do {
-		char *kaddr;
+		char *kaddr = nilfs_get_page(dir, n, &page);
 
-		page = nilfs_get_page(dir, n);
-		if (!IS_ERR(page)) {
-			kaddr = page_address(page);
-			de = (struct nilfs_dir_entry *)kaddr;
-			kaddr += nilfs_last_byte(dir, n) - reclen;
-			while ((char *) de <= kaddr) {
-				if (de->rec_len == 0) {
-					nilfs_error(dir->i_sb,
-						"zero-length directory entry");
-					nilfs_put_page(page);
-					goto out;
-				}
-				if (nilfs_match(namelen, name, de))
-					goto found;
-				de = nilfs_next_entry(de);
+		if (IS_ERR(kaddr))
+			return ERR_CAST(kaddr);
+
+		de = (struct nilfs_dir_entry *)kaddr;
+		kaddr += nilfs_last_byte(dir, n) - reclen;
+		while ((char *)de <= kaddr) {
+			if (de->rec_len == 0) {
+				nilfs_error(dir->i_sb,
+					    "zero-length directory entry");
+				nilfs_put_page(page);
+				goto out;
 			}
-			nilfs_put_page(page);
+			if (nilfs_match(namelen, name, de))
+				goto found;
+			de = nilfs_next_entry(de);
 		}
+		nilfs_put_page(page);
+
 		if (++n >= npages)
 			n = 0;
 		/* next page is past the blocks we've got */
@@ -377,7 +384,7 @@
 		}
 	} while (n != start);
 out:
-	return NULL;
+	return ERR_PTR(-ENOENT);
 
 found:
 	*res_page = page;
@@ -387,34 +394,57 @@
 
 struct nilfs_dir_entry *nilfs_dotdot(struct inode *dir, struct page **p)
 {
-	struct page *page = nilfs_get_page(dir, 0);
-	struct nilfs_dir_entry *de = NULL;
+	struct page *page;
+	struct nilfs_dir_entry *de, *next_de;
+	size_t limit;
+	char *msg;
+
+	de = nilfs_get_page(dir, 0, &page);
+	if (IS_ERR(de))
+		return NULL;
+
+	limit = nilfs_last_byte(dir, 0);  /* is a multiple of chunk size */
+	if (unlikely(!limit || le64_to_cpu(de->inode) != dir->i_ino ||
+		     !nilfs_match(1, ".", de))) {
+		msg = "missing '.'";
+		goto fail;
+	}
 
-	if (!IS_ERR(page)) {
-		de = nilfs_next_entry(
-			(struct nilfs_dir_entry *)page_address(page));
-		*p = page;
+	next_de = nilfs_next_entry(de);
+	/*
+	 * If "next_de" has not reached the end of the chunk, there is
+	 * at least one more record.  Check whether it matches "..".
+	 */
+	if (unlikely((char *)next_de == (char *)de + nilfs_chunk_size(dir) ||
+		     !nilfs_match(2, "..", next_de))) {
+		msg = "missing '..'";
+		goto fail;
 	}
-	return de;
+	*p = page;
+	return next_de;
+
+fail:
+	nilfs_error(dir->i_sb, "directory #%lu %s", dir->i_ino, msg);
+	nilfs_put_page(page);
+	return NULL;
 }
 
-ino_t nilfs_inode_by_name(struct inode *dir, const struct qstr *qstr)
+int nilfs_inode_by_name(struct inode *dir, const struct qstr *qstr, ino_t *ino)
 {
-	ino_t res = 0;
 	struct nilfs_dir_entry *de;
 	struct page *page;
 
 	de = nilfs_find_entry(dir, qstr, &page);
-	if (de) {
-		res = le64_to_cpu(de->inode);
-		kunmap(page);
-		put_page(page);
-	}
-	return res;
+	if (IS_ERR(de))
+		return PTR_ERR(de);
+
+	*ino = le64_to_cpu(de->inode);
+	kunmap(page);
+	put_page(page);
+	return 0;
 }
 
-/* Releases the page */
-void nilfs_set_link(struct inode *dir, struct nilfs_dir_entry *de,
+int nilfs_set_link(struct inode *dir, struct nilfs_dir_entry *de,
 		    struct page *page, struct inode *inode)
 {
 	unsigned int from = (char *)de - (char *)page_address(page);
@@ -424,12 +454,15 @@
 
 	lock_page(page);
 	err = nilfs_prepare_chunk(page, from, to);
-	BUG_ON(err);
+	if (unlikely(err)) {
+		unlock_page(page);
+		return err;
+	}
 	de->inode = cpu_to_le64(inode->i_ino);
 	nilfs_set_de_type(de, inode);
 	nilfs_commit_chunk(page, mapping, from, to);
-	nilfs_put_page(page);
 	dir->i_mtime = dir->i_ctime = current_time(dir);
+	return 0;
 }
 
 /*
@@ -459,12 +492,11 @@
 	for (n = 0; n <= npages; n++) {
 		char *dir_end;
 
-		page = nilfs_get_page(dir, n);
-		err = PTR_ERR(page);
-		if (IS_ERR(page))
+		kaddr = nilfs_get_page(dir, n, &page);
+		err = PTR_ERR(kaddr);
+		if (IS_ERR(kaddr))
 			goto out;
 		lock_page(page);
-		kaddr = page_address(page);
 		dir_end = kaddr + nilfs_last_byte(dir, n);
 		de = (struct nilfs_dir_entry *)kaddr;
 		kaddr += PAGE_SIZE - reclen;
@@ -533,7 +565,7 @@
 
 /*
  * nilfs_delete_entry deletes a directory entry by merging it with the
- * previous entry. Page is up-to-date. Releases the page.
+ * previous entry. Page is up-to-date.
  */
 int nilfs_delete_entry(struct nilfs_dir_entry *dir, struct page *page)
 {
@@ -562,14 +594,16 @@
 		from = (char *)pde - (char *)page_address(page);
 	lock_page(page);
 	err = nilfs_prepare_chunk(page, from, to);
-	BUG_ON(err);
+	if (unlikely(err)) {
+		unlock_page(page);
+		goto out;
+	}
 	if (pde)
 		pde->rec_len = nilfs_rec_len_to_disk(to - from);
 	dir->inode = 0;
 	nilfs_commit_chunk(page, mapping, from, to);
 	inode->i_ctime = inode->i_mtime = current_time(inode);
 out:
-	nilfs_put_page(page);
 	return err;
 }
 
@@ -627,11 +661,10 @@
 		char *kaddr;
 		struct nilfs_dir_entry *de;
 
-		page = nilfs_get_page(inode, i);
-		if (IS_ERR(page))
-			continue;
+		kaddr = nilfs_get_page(inode, i, &page);
+		if (IS_ERR(kaddr))
+			return 0;
 
-		kaddr = page_address(page);
 		de = (struct nilfs_dir_entry *)kaddr;
 		kaddr += nilfs_last_byte(inode, i) - NILFS_DIR_REC_LEN(1);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/direct.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/direct.c
@@ -66,7 +66,7 @@
 		dat = nilfs_bmap_get_dat(direct);
 		ret = nilfs_dat_translate(dat, ptr, &blocknr);
 		if (ret < 0)
-			return ret;
+			goto dat_error;
 		ptr = blocknr;
 	}
 
@@ -79,7 +79,7 @@
 		if (dat) {
 			ret = nilfs_dat_translate(dat, ptr2, &blocknr);
 			if (ret < 0)
-				return ret;
+				goto dat_error;
 			ptr2 = blocknr;
 		}
 		if (ptr2 != ptr + cnt)
@@ -87,6 +87,11 @@
 	}
 	*ptrp = ptr;
 	return cnt;
+
+ dat_error:
+	if (ret == -ENOENT)
+		ret = -EINVAL;  /* Notify bmap layer of metadata corruption */
+	return ret;
 }
 
 static __u64
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/file.c
@@ -105,7 +105,13 @@
 	nilfs_transaction_commit(inode->i_sb);
 
  mapped:
-	wait_for_stable_page(page);
+	/*
+	 * Since checksumming including data blocks is performed to determine
+	 * the validity of the log to be written and used for recovery, it is
+	 * necessary to wait for writeback to finish here, regardless of the
+	 * stable write requirement of the backing device.
+	 */
+	wait_on_page_writeback(page);
  out:
 	sb_end_pagefault(inode->i_sb);
 	return block_page_mkwrite_return(ret);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/gcinode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/gcinode.c
@@ -73,10 +73,8 @@
 		struct the_nilfs *nilfs = inode->i_sb->s_fs_info;
 
 		err = nilfs_dat_translate(nilfs->ns_dat, vbn, &pbn);
-		if (unlikely(err)) { /* -EIO, -ENOMEM, -ENOENT */
-			brelse(bh);
+		if (unlikely(err)) /* -EIO, -ENOMEM, -ENOENT */
 			goto failed;
-		}
 	}
 
 	lock_buffer(bh);
@@ -85,10 +83,8 @@
 		goto out;
 	}
 
-	if (!buffer_mapped(bh)) {
-		bh->b_bdev = inode->i_sb->s_bdev;
+	if (!buffer_mapped(bh))
 		set_buffer_mapped(bh);
-	}
 	bh->b_blocknr = pbn;
 	bh->b_end_io = end_buffer_read_sync;
 	get_bh(bh);
@@ -102,6 +98,8 @@
  failed:
 	unlock_page(bh->b_page);
 	put_page(bh->b_page);
+	if (unlikely(err))
+		brelse(bh);
 	return err;
 }
 
@@ -126,9 +124,10 @@
 int nilfs_gccache_submit_read_node(struct inode *inode, sector_t pbn,
 				   __u64 vbn, struct buffer_head **out_bh)
 {
+	struct inode *btnc_inode = NILFS_I(inode)->i_assoc_inode;
 	int ret;
 
-	ret = nilfs_btnode_submit_block(&NILFS_I(inode)->i_btnode_cache,
+	ret = nilfs_btnode_submit_block(btnc_inode->i_mapping,
 					vbn ? : pbn, pbn, REQ_OP_READ, 0,
 					out_bh, &pbn);
 	if (ret == -EEXIST) /* internal code (cache hit) */
@@ -170,7 +169,7 @@
 	ii->i_flags = 0;
 	nilfs_bmap_init_gc(ii->i_bmap);
 
-	return 0;
+	return nilfs_attach_btree_node_cache(inode);
 }
 
 /**
@@ -185,7 +184,7 @@
 		ii = list_first_entry(head, struct nilfs_inode_info, i_dirty);
 		list_del_init(&ii->i_dirty);
 		truncate_inode_pages(&ii->vfs_inode.i_data, 0);
-		nilfs_btnode_cache_clear(&ii->i_btnode_cache);
+		nilfs_btnode_cache_clear(ii->i_assoc_inode->i_mapping);
 		iput(&ii->vfs_inode);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/ifile.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/ifile.c
@@ -55,13 +55,10 @@
 	struct nilfs_palloc_req req;
 	int ret;
 
-	req.pr_entry_nr = 0;  /*
-			       * 0 says find free inode from beginning
-			       * of a group. dull code!!
-			       */
+	req.pr_entry_nr = NILFS_FIRST_INO(ifile->i_sb);
 	req.pr_entry_bh = NULL;
 
-	ret = nilfs_palloc_prepare_alloc_entry(ifile, &req);
+	ret = nilfs_palloc_prepare_alloc_entry(ifile, &req, false);
 	if (!ret) {
 		ret = nilfs_palloc_get_entry_block(ifile, req.pr_entry_nr, 1,
 						   &req.pr_entry_bh);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/inode.c
@@ -29,12 +29,16 @@
  * @cno: checkpoint number
  * @root: pointer on NILFS root object (mounted checkpoint)
  * @for_gc: inode for GC flag
+ * @for_btnc: inode for B-tree node cache flag
+ * @for_shadow: inode for shadowed page cache flag
  */
 struct nilfs_iget_args {
 	u64 ino;
 	__u64 cno;
 	struct nilfs_root *root;
-	int for_gc;
+	bool for_gc;
+	bool for_btnc;
+	bool for_shadow;
 };
 
 static int nilfs_iget_test(struct inode *inode, void *opaque);
@@ -108,7 +112,7 @@
 					   "%s (ino=%lu): a race condition while inserting a data block at offset=%llu",
 					   __func__, inode->i_ino,
 					   (unsigned long long)blkoff);
-				err = 0;
+				err = -EAGAIN;
 			}
 			nilfs_transaction_abort(inode->i_sb);
 			goto out;
@@ -158,7 +162,7 @@
 	int err = 0;
 
 	if (sb_rdonly(inode->i_sb)) {
-		nilfs_clear_dirty_pages(mapping, false);
+		nilfs_clear_dirty_pages(mapping);
 		return -EROFS;
 	}
 
@@ -181,7 +185,7 @@
 		 * have dirty pages that try to be flushed in background.
 		 * So, here we simply discard this dirty page.
 		 */
-		nilfs_clear_dirty_page(page, false);
+		nilfs_clear_dirty_page(page);
 		unlock_page(page);
 		return -EROFS;
 	}
@@ -314,7 +318,8 @@
 				     unsigned long ino)
 {
 	struct nilfs_iget_args args = {
-		.ino = ino, .root = root, .cno = 0, .for_gc = 0
+		.ino = ino, .root = root, .cno = 0, .for_gc = false,
+		.for_btnc = false, .for_shadow = false
 	};
 
 	return insert_inode_locked4(inode, ino, nilfs_iget_test, &args);
@@ -327,6 +332,7 @@
 	struct inode *inode;
 	struct nilfs_inode_info *ii;
 	struct nilfs_root *root;
+	struct buffer_head *bh;
 	int err = -ENOMEM;
 	ino_t ino;
 
@@ -342,11 +348,25 @@
 	ii->i_state = BIT(NILFS_I_NEW);
 	ii->i_root = root;
 
-	err = nilfs_ifile_create_inode(root->ifile, &ino, &ii->i_bh);
+	err = nilfs_ifile_create_inode(root->ifile, &ino, &bh);
 	if (unlikely(err))
 		goto failed_ifile_create_inode;
 	/* reference count of i_bh inherits from nilfs_mdt_read_block() */
 
+	if (unlikely(ino < NILFS_USER_INO)) {
+		nilfs_warn(sb,
+			   "inode bitmap is inconsistent for reserved inodes");
+		do {
+			brelse(bh);
+			err = nilfs_ifile_create_inode(root->ifile, &ino, &bh);
+			if (unlikely(err))
+				goto failed_ifile_create_inode;
+		} while (ino < NILFS_USER_INO);
+
+		nilfs_info(sb, "repaired inode bitmap for reserved inodes");
+	}
+	ii->i_bh = bh;
+
 	atomic64_inc(&root->inodes_count);
 	inode_init_owner(&init_user_ns, inode, dir, mode);
 	inode->i_ino = ino;
@@ -439,6 +459,8 @@
 	inode->i_atime.tv_nsec = le32_to_cpu(raw_inode->i_mtime_nsec);
 	inode->i_ctime.tv_nsec = le32_to_cpu(raw_inode->i_ctime_nsec);
 	inode->i_mtime.tv_nsec = le32_to_cpu(raw_inode->i_mtime_nsec);
+	if (nilfs_is_metadata_file_inode(inode) && !S_ISREG(inode->i_mode))
+		return -EIO; /* this inode is for metadata and corrupted */
 	if (inode->i_nlink == 0)
 		return -ESTALE; /* this inode is deleted */
 
@@ -527,6 +549,19 @@
 		return 0;
 
 	ii = NILFS_I(inode);
+	if (test_bit(NILFS_I_BTNC, &ii->i_state)) {
+		if (!args->for_btnc)
+			return 0;
+	} else if (args->for_btnc) {
+		return 0;
+	}
+	if (test_bit(NILFS_I_SHADOW, &ii->i_state)) {
+		if (!args->for_shadow)
+			return 0;
+	} else if (args->for_shadow) {
+		return 0;
+	}
+
 	if (!test_bit(NILFS_I_GCINODE, &ii->i_state))
 		return !args->for_gc;
 
@@ -538,15 +573,17 @@
 	struct nilfs_iget_args *args = opaque;
 
 	inode->i_ino = args->ino;
-	if (args->for_gc) {
+	NILFS_I(inode)->i_cno = args->cno;
+	NILFS_I(inode)->i_root = args->root;
+	if (args->root && args->ino == NILFS_ROOT_INO)
+		nilfs_get_root(args->root);
+
+	if (args->for_gc)
 		NILFS_I(inode)->i_state = BIT(NILFS_I_GCINODE);
-		NILFS_I(inode)->i_cno = args->cno;
-		NILFS_I(inode)->i_root = NULL;
-	} else {
-		if (args->root && args->ino == NILFS_ROOT_INO)
-			nilfs_get_root(args->root);
-		NILFS_I(inode)->i_root = args->root;
-	}
+	if (args->for_btnc)
+		NILFS_I(inode)->i_state |= BIT(NILFS_I_BTNC);
+	if (args->for_shadow)
+		NILFS_I(inode)->i_state |= BIT(NILFS_I_SHADOW);
 	return 0;
 }
 
@@ -554,7 +591,8 @@
 			    unsigned long ino)
 {
 	struct nilfs_iget_args args = {
-		.ino = ino, .root = root, .cno = 0, .for_gc = 0
+		.ino = ino, .root = root, .cno = 0, .for_gc = false,
+		.for_btnc = false, .for_shadow = false
 	};
 
 	return ilookup5(sb, ino, nilfs_iget_test, &args);
@@ -564,7 +602,8 @@
 				unsigned long ino)
 {
 	struct nilfs_iget_args args = {
-		.ino = ino, .root = root, .cno = 0, .for_gc = 0
+		.ino = ino, .root = root, .cno = 0, .for_gc = false,
+		.for_btnc = false, .for_shadow = false
 	};
 
 	return iget5_locked(sb, ino, nilfs_iget_test, nilfs_iget_set, &args);
@@ -579,8 +618,14 @@
 	inode = nilfs_iget_locked(sb, root, ino);
 	if (unlikely(!inode))
 		return ERR_PTR(-ENOMEM);
-	if (!(inode->i_state & I_NEW))
+
+	if (!(inode->i_state & I_NEW)) {
+		if (!inode->i_nlink) {
+			iput(inode);
+			return ERR_PTR(-ESTALE);
+		}
 		return inode;
+	}
 
 	err = __nilfs_read_inode(sb, root, ino, inode);
 	if (unlikely(err)) {
@@ -595,7 +640,8 @@
 				__u64 cno)
 {
 	struct nilfs_iget_args args = {
-		.ino = ino, .root = NULL, .cno = cno, .for_gc = 1
+		.ino = ino, .root = NULL, .cno = cno, .for_gc = true,
+		.for_btnc = false, .for_shadow = false
 	};
 	struct inode *inode;
 	int err;
@@ -615,6 +661,113 @@
 	return inode;
 }
 
+/**
+ * nilfs_attach_btree_node_cache - attach a B-tree node cache to the inode
+ * @inode: inode object
+ *
+ * nilfs_attach_btree_node_cache() attaches a B-tree node cache to @inode,
+ * or does nothing if the inode already has it.  This function allocates
+ * an additional inode to maintain page cache of B-tree nodes one-on-one.
+ *
+ * Return Value: On success, 0 is returned. On errors, one of the following
+ * negative error code is returned.
+ *
+ * %-ENOMEM - Insufficient memory available.
+ */
+int nilfs_attach_btree_node_cache(struct inode *inode)
+{
+	struct nilfs_inode_info *ii = NILFS_I(inode);
+	struct inode *btnc_inode;
+	struct nilfs_iget_args args;
+
+	if (ii->i_assoc_inode)
+		return 0;
+
+	args.ino = inode->i_ino;
+	args.root = ii->i_root;
+	args.cno = ii->i_cno;
+	args.for_gc = test_bit(NILFS_I_GCINODE, &ii->i_state) != 0;
+	args.for_btnc = true;
+	args.for_shadow = test_bit(NILFS_I_SHADOW, &ii->i_state) != 0;
+
+	btnc_inode = iget5_locked(inode->i_sb, inode->i_ino, nilfs_iget_test,
+				  nilfs_iget_set, &args);
+	if (unlikely(!btnc_inode))
+		return -ENOMEM;
+	if (btnc_inode->i_state & I_NEW) {
+		nilfs_init_btnc_inode(btnc_inode);
+		unlock_new_inode(btnc_inode);
+	}
+	NILFS_I(btnc_inode)->i_assoc_inode = inode;
+	NILFS_I(btnc_inode)->i_bmap = ii->i_bmap;
+	ii->i_assoc_inode = btnc_inode;
+
+	return 0;
+}
+
+/**
+ * nilfs_detach_btree_node_cache - detach the B-tree node cache from the inode
+ * @inode: inode object
+ *
+ * nilfs_detach_btree_node_cache() detaches the B-tree node cache and its
+ * holder inode bound to @inode, or does nothing if @inode doesn't have it.
+ */
+void nilfs_detach_btree_node_cache(struct inode *inode)
+{
+	struct nilfs_inode_info *ii = NILFS_I(inode);
+	struct inode *btnc_inode = ii->i_assoc_inode;
+
+	if (btnc_inode) {
+		NILFS_I(btnc_inode)->i_assoc_inode = NULL;
+		ii->i_assoc_inode = NULL;
+		iput(btnc_inode);
+	}
+}
+
+/**
+ * nilfs_iget_for_shadow - obtain inode for shadow mapping
+ * @inode: inode object that uses shadow mapping
+ *
+ * nilfs_iget_for_shadow() allocates a pair of inodes that holds page
+ * caches for shadow mapping.  The page cache for data pages is set up
+ * in one inode and the one for b-tree node pages is set up in the
+ * other inode, which is attached to the former inode.
+ *
+ * Return Value: On success, a pointer to the inode for data pages is
+ * returned. On errors, one of the following negative error code is returned
+ * in a pointer type.
+ *
+ * %-ENOMEM - Insufficient memory available.
+ */
+struct inode *nilfs_iget_for_shadow(struct inode *inode)
+{
+	struct nilfs_iget_args args = {
+		.ino = inode->i_ino, .root = NULL, .cno = 0, .for_gc = false,
+		.for_btnc = false, .for_shadow = true
+	};
+	struct inode *s_inode;
+	int err;
+
+	s_inode = iget5_locked(inode->i_sb, inode->i_ino, nilfs_iget_test,
+			       nilfs_iget_set, &args);
+	if (unlikely(!s_inode))
+		return ERR_PTR(-ENOMEM);
+	if (!(s_inode->i_state & I_NEW))
+		return inode;
+
+	NILFS_I(s_inode)->i_flags = 0;
+	memset(NILFS_I(s_inode)->i_bmap, 0, sizeof(struct nilfs_bmap));
+	mapping_set_gfp_mask(s_inode->i_mapping, GFP_NOFS);
+
+	err = nilfs_attach_btree_node_cache(s_inode);
+	if (unlikely(err)) {
+		iget_failed(s_inode);
+		return ERR_PTR(err);
+	}
+	unlock_new_inode(s_inode);
+	return s_inode;
+}
+
 void nilfs_write_inode_common(struct inode *inode,
 			      struct nilfs_inode *raw_inode, int has_bmap)
 {
@@ -762,7 +915,8 @@
 	if (test_bit(NILFS_I_BMAP, &ii->i_state))
 		nilfs_bmap_clear(ii->i_bmap);
 
-	nilfs_btnode_cache_clear(&ii->i_btnode_cache);
+	if (!test_bit(NILFS_I_BTNC, &ii->i_state))
+		nilfs_detach_btree_node_cache(inode);
 
 	if (ii->i_root && inode->i_ino == NILFS_ROOT_INO)
 		nilfs_put_root(ii->i_root);
@@ -773,6 +927,7 @@
 	struct nilfs_transaction_info ti;
 	struct super_block *sb = inode->i_sb;
 	struct nilfs_inode_info *ii = NILFS_I(inode);
+	struct the_nilfs *nilfs;
 	int ret;
 
 	if (inode->i_nlink || !ii->i_root || unlikely(is_bad_inode(inode))) {
@@ -785,6 +940,23 @@
 
 	truncate_inode_pages_final(&inode->i_data);
 
+	nilfs = sb->s_fs_info;
+	if (unlikely(sb_rdonly(sb) || !nilfs->ns_writer)) {
+		/*
+		 * If this inode is about to be disposed after the file system
+		 * has been degraded to read-only due to file system corruption
+		 * or after the writer has been detached, do not make any
+		 * changes that cause writes, just clear it.
+		 * Do this check after read-locking ns_segctor_sem by
+		 * nilfs_transaction_begin() in order to avoid a race with
+		 * the writer detach operation.
+		 */
+		clear_inode(inode);
+		nilfs_clear_inode(inode);
+		nilfs_transaction_abort(sb);
+		return;
+	}
+
 	/* TODO: some of the following operations may fail.  */
 	nilfs_truncate_bmap(ii, 0);
 	nilfs_mark_inode_dirty(inode);
@@ -863,7 +1035,7 @@
 	int err;
 
 	spin_lock(&nilfs->ns_inode_lock);
-	if (ii->i_bh == NULL) {
+	if (ii->i_bh == NULL || unlikely(!buffer_uptodate(ii->i_bh))) {
 		spin_unlock(&nilfs->ns_inode_lock);
 		err = nilfs_ifile_get_inode_block(ii->i_root->ifile,
 						  inode->i_ino, pbh);
@@ -872,7 +1044,10 @@
 		spin_lock(&nilfs->ns_inode_lock);
 		if (ii->i_bh == NULL)
 			ii->i_bh = *pbh;
-		else {
+		else if (unlikely(!buffer_uptodate(ii->i_bh))) {
+			__brelse(ii->i_bh);
+			ii->i_bh = *pbh;
+		} else {
 			brelse(*pbh);
 			*pbh = ii->i_bh;
 		}
@@ -939,9 +1114,17 @@
 
 int __nilfs_mark_inode_dirty(struct inode *inode, int flags)
 {
+	struct the_nilfs *nilfs = inode->i_sb->s_fs_info;
 	struct buffer_head *ibh;
 	int err;
 
+	/*
+	 * Do not dirty inodes after the log writer has been detached
+	 * and its nilfs_root struct has been freed.
+	 */
+	if (unlikely(nilfs_purging(nilfs)))
+		return 0;
+
 	err = nilfs_load_inode_block(inode, &ibh);
 	if (unlikely(err)) {
 		nilfs_warn(inode->i_sb,
@@ -1082,7 +1265,7 @@
 			if (size) {
 				if (phys && blkphy << blkbits == phys + size) {
 					/* The current extent goes on */
-					size += n << blkbits;
+					size += (u64)n << blkbits;
 				} else {
 					/* Terminate the current extent */
 					ret = fiemap_fill_next_extent(
@@ -1095,14 +1278,14 @@
 					flags = FIEMAP_EXTENT_MERGED;
 					logical = blkoff << blkbits;
 					phys = blkphy << blkbits;
-					size = n << blkbits;
+					size = (u64)n << blkbits;
 				}
 			} else {
 				/* Start a new extent */
 				flags = FIEMAP_EXTENT_MERGED;
 				logical = blkoff << blkbits;
 				phys = blkphy << blkbits;
-				size = n << blkbits;
+				size = (u64)n << blkbits;
 			}
 			blkoff += n;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/ioctl.c
@@ -60,7 +60,7 @@
 	if (argv->v_nmembs == 0)
 		return 0;
 
-	if (argv->v_size > PAGE_SIZE)
+	if ((size_t)argv->v_size > PAGE_SIZE)
 		return -EINVAL;
 
 	/*
@@ -71,7 +71,7 @@
 	if (argv->v_index > ~(__u64)0 - argv->v_nmembs)
 		return -EINVAL;
 
-	buf = (void *)__get_free_pages(GFP_NOFS, 0);
+	buf = (void *)get_zeroed_page(GFP_NOFS);
 	if (unlikely(!buf))
 		return -ENOMEM;
 	maxmembs = PAGE_SIZE / argv->v_size;
@@ -1114,7 +1114,14 @@
 
 	minseg = range[0] + segbytes - 1;
 	do_div(minseg, segbytes);
+
+	if (range[1] < 4096)
+		goto out;
+
 	maxseg = NILFS_SB2_OFFSET_BYTES(range[1]);
+	if (maxseg < segbytes)
+		goto out;
+
 	do_div(maxseg, segbytes);
 	maxseg--;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/mdt.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/mdt.c
@@ -89,7 +89,6 @@
 	if (buffer_uptodate(bh))
 		goto failed_bh;
 
-	bh->b_bdev = sb->s_bdev;
 	err = nilfs_mdt_insert_new_block(inode, block, bh, init_block);
 	if (likely(!err)) {
 		get_bh(bh);
@@ -411,7 +410,7 @@
 		 * have dirty pages that try to be flushed in background.
 		 * So, here we simply discard this dirty page.
 		 */
-		nilfs_clear_dirty_page(page, false);
+		nilfs_clear_dirty_page(page);
 		unlock_page(page);
 		return -EROFS;
 	}
@@ -470,9 +469,18 @@
 void nilfs_mdt_clear(struct inode *inode)
 {
 	struct nilfs_mdt_info *mdi = NILFS_MDT(inode);
+	struct nilfs_shadow_map *shadow = mdi->mi_shadow;
 
 	if (mdi->mi_palloc_cache)
 		nilfs_palloc_destroy_cache(inode);
+
+	if (shadow) {
+		struct inode *s_inode = shadow->inode;
+
+		shadow->inode = NULL;
+		iput(s_inode);
+		mdi->mi_shadow = NULL;
+	}
 }
 
 /**
@@ -506,12 +514,15 @@
 			       struct nilfs_shadow_map *shadow)
 {
 	struct nilfs_mdt_info *mi = NILFS_MDT(inode);
+	struct inode *s_inode;
 
 	INIT_LIST_HEAD(&shadow->frozen_buffers);
-	address_space_init_once(&shadow->frozen_data);
-	nilfs_mapping_init(&shadow->frozen_data, inode);
-	address_space_init_once(&shadow->frozen_btnodes);
-	nilfs_mapping_init(&shadow->frozen_btnodes, inode);
+
+	s_inode = nilfs_iget_for_shadow(inode);
+	if (IS_ERR(s_inode))
+		return PTR_ERR(s_inode);
+
+	shadow->inode = s_inode;
 	mi->mi_shadow = shadow;
 	return 0;
 }
@@ -525,14 +536,15 @@
 	struct nilfs_mdt_info *mi = NILFS_MDT(inode);
 	struct nilfs_inode_info *ii = NILFS_I(inode);
 	struct nilfs_shadow_map *shadow = mi->mi_shadow;
+	struct inode *s_inode = shadow->inode;
 	int ret;
 
-	ret = nilfs_copy_dirty_pages(&shadow->frozen_data, inode->i_mapping);
+	ret = nilfs_copy_dirty_pages(s_inode->i_mapping, inode->i_mapping);
 	if (ret)
 		goto out;
 
-	ret = nilfs_copy_dirty_pages(&shadow->frozen_btnodes,
-				     &ii->i_btnode_cache);
+	ret = nilfs_copy_dirty_pages(NILFS_I(s_inode)->i_assoc_inode->i_mapping,
+				     ii->i_assoc_inode->i_mapping);
 	if (ret)
 		goto out;
 
@@ -548,7 +560,7 @@
 	struct page *page;
 	int blkbits = inode->i_blkbits;
 
-	page = grab_cache_page(&shadow->frozen_data, bh->b_page->index);
+	page = grab_cache_page(shadow->inode->i_mapping, bh->b_page->index);
 	if (!page)
 		return -ENOMEM;
 
@@ -580,7 +592,7 @@
 	struct page *page;
 	int n;
 
-	page = find_lock_page(&shadow->frozen_data, bh->b_page->index);
+	page = find_lock_page(shadow->inode->i_mapping, bh->b_page->index);
 	if (page) {
 		if (page_has_buffers(page)) {
 			n = bh_offset(bh) >> inode->i_blkbits;
@@ -620,11 +632,12 @@
 	if (mi->mi_palloc_cache)
 		nilfs_palloc_clear_cache(inode);
 
-	nilfs_clear_dirty_pages(inode->i_mapping, true);
-	nilfs_copy_back_pages(inode->i_mapping, &shadow->frozen_data);
+	nilfs_clear_dirty_pages(inode->i_mapping);
+	nilfs_copy_back_pages(inode->i_mapping, shadow->inode->i_mapping);
 
-	nilfs_clear_dirty_pages(&ii->i_btnode_cache, true);
-	nilfs_copy_back_pages(&ii->i_btnode_cache, &shadow->frozen_btnodes);
+	nilfs_clear_dirty_pages(ii->i_assoc_inode->i_mapping);
+	nilfs_copy_back_pages(ii->i_assoc_inode->i_mapping,
+			      NILFS_I(shadow->inode)->i_assoc_inode->i_mapping);
 
 	nilfs_bmap_restore(ii->i_bmap, &shadow->bmap_store);
 
@@ -639,10 +652,11 @@
 {
 	struct nilfs_mdt_info *mi = NILFS_MDT(inode);
 	struct nilfs_shadow_map *shadow = mi->mi_shadow;
+	struct inode *shadow_btnc_inode = NILFS_I(shadow->inode)->i_assoc_inode;
 
 	down_write(&mi->mi_sem);
 	nilfs_release_frozen_buffers(shadow);
-	truncate_inode_pages(&shadow->frozen_data, 0);
-	truncate_inode_pages(&shadow->frozen_btnodes, 0);
+	truncate_inode_pages(shadow->inode->i_mapping, 0);
+	truncate_inode_pages(shadow_btnc_inode->i_mapping, 0);
 	up_write(&mi->mi_sem);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/mdt.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/mdt.h
@@ -18,14 +18,12 @@
 /**
  * struct nilfs_shadow_map - shadow mapping of meta data file
  * @bmap_store: shadow copy of bmap state
- * @frozen_data: shadowed dirty data pages
- * @frozen_btnodes: shadowed dirty b-tree nodes' pages
+ * @inode: holder of page caches used in shadow mapping
  * @frozen_buffers: list of frozen buffers
  */
 struct nilfs_shadow_map {
 	struct nilfs_bmap_store bmap_store;
-	struct address_space frozen_data;
-	struct address_space frozen_btnodes;
+	struct inode *inode;
 	struct list_head frozen_buffers;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/namei.c
@@ -55,12 +55,25 @@
 {
 	struct inode *inode;
 	ino_t ino;
+	int res;
 
 	if (dentry->d_name.len > NILFS_NAME_LEN)
 		return ERR_PTR(-ENAMETOOLONG);
 
-	ino = nilfs_inode_by_name(dir, &dentry->d_name);
-	inode = ino ? nilfs_iget(dir->i_sb, NILFS_I(dir)->i_root, ino) : NULL;
+	res = nilfs_inode_by_name(dir, &dentry->d_name, &ino);
+	if (res) {
+		if (res != -ENOENT)
+			return ERR_PTR(res);
+		inode = NULL;
+	} else {
+		inode = nilfs_iget(dir->i_sb, NILFS_I(dir)->i_root, ino);
+		if (inode == ERR_PTR(-ESTALE)) {
+			nilfs_error(dir->i_sb,
+					"deleted inode referenced: %lu", ino);
+			return ERR_PTR(-EIO);
+		}
+	}
+
 	return d_splice_alias(inode, dentry);
 }
 
@@ -149,6 +162,9 @@
 	/* slow symlink */
 	inode->i_op = &nilfs_symlink_inode_operations;
 	inode_nohighmem(inode);
+	mapping_set_gfp_mask(inode->i_mapping,
+			     mapping_gfp_constraint(inode->i_mapping,
+						    ~__GFP_FS));
 	inode->i_mapping->a_ops = &nilfs_aops;
 	err = page_symlink(inode, symname, l);
 	if (err)
@@ -263,10 +279,11 @@
 	struct page *page;
 	int err;
 
-	err = -ENOENT;
 	de = nilfs_find_entry(dir, &dentry->d_name, &page);
-	if (!de)
+	if (IS_ERR(de)) {
+		err = PTR_ERR(de);
 		goto out;
+	}
 
 	inode = d_inode(dentry);
 	err = -EIO;
@@ -280,6 +297,7 @@
 		set_nlink(inode, 1);
 	}
 	err = nilfs_delete_entry(de, page);
+	nilfs_put_page(page);
 	if (err)
 		goto out;
 
@@ -361,10 +379,11 @@
 	if (unlikely(err))
 		return err;
 
-	err = -ENOENT;
 	old_de = nilfs_find_entry(old_dir, &old_dentry->d_name, &old_page);
-	if (!old_de)
+	if (IS_ERR(old_de)) {
+		err = PTR_ERR(old_de);
 		goto out;
+	}
 
 	if (S_ISDIR(old_inode->i_mode)) {
 		err = -EIO;
@@ -381,11 +400,16 @@
 		if (dir_de && !nilfs_empty_dir(new_inode))
 			goto out_dir;
 
-		err = -ENOENT;
-		new_de = nilfs_find_entry(new_dir, &new_dentry->d_name, &new_page);
-		if (!new_de)
+		new_de = nilfs_find_entry(new_dir, &new_dentry->d_name,
+					  &new_page);
+		if (IS_ERR(new_de)) {
+			err = PTR_ERR(new_de);
+			goto out_dir;
+		}
+		err = nilfs_set_link(new_dir, new_de, new_page, old_inode);
+		nilfs_put_page(new_page);
+		if (unlikely(err))
 			goto out_dir;
-		nilfs_set_link(new_dir, new_de, new_page, old_inode);
 		nilfs_mark_inode_dirty(new_dir);
 		new_inode->i_ctime = current_time(new_inode);
 		if (dir_de)
@@ -408,28 +432,27 @@
 	 */
 	old_inode->i_ctime = current_time(old_inode);
 
-	nilfs_delete_entry(old_de, old_page);
-
-	if (dir_de) {
-		nilfs_set_link(old_inode, dir_de, dir_page, new_dir);
-		drop_nlink(old_dir);
+	err = nilfs_delete_entry(old_de, old_page);
+	if (likely(!err)) {
+		if (dir_de) {
+			err = nilfs_set_link(old_inode, dir_de, dir_page,
+					     new_dir);
+			drop_nlink(old_dir);
+		}
+		nilfs_mark_inode_dirty(old_dir);
 	}
-	nilfs_mark_inode_dirty(old_dir);
 	nilfs_mark_inode_dirty(old_inode);
 
-	err = nilfs_transaction_commit(old_dir->i_sb);
-	return err;
-
 out_dir:
-	if (dir_de) {
-		kunmap(dir_page);
-		put_page(dir_page);
-	}
+	if (dir_de)
+		nilfs_put_page(dir_page);
 out_old:
-	kunmap(old_page);
-	put_page(old_page);
+	nilfs_put_page(old_page);
 out:
-	nilfs_transaction_abort(old_dir->i_sb);
+	if (likely(!err))
+		err = nilfs_transaction_commit(old_dir->i_sb);
+	else
+		nilfs_transaction_abort(old_dir->i_sb);
 	return err;
 }
 
@@ -438,13 +461,14 @@
  */
 static struct dentry *nilfs_get_parent(struct dentry *child)
 {
-	unsigned long ino;
+	ino_t ino;
+	int res;
 	struct inode *inode;
 	struct nilfs_root *root;
 
-	ino = nilfs_inode_by_name(d_inode(child), &dotdot_name);
-	if (!ino)
-		return ERR_PTR(-ENOENT);
+	res = nilfs_inode_by_name(d_inode(child), &dotdot_name, &ino);
+	if (res)
+		return ERR_PTR(res);
 
 	root = NILFS_I(d_inode(child))->i_root;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/nilfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/nilfs.h
@@ -28,7 +28,7 @@
  * @i_xattr: <TODO>
  * @i_dir_start_lookup: page index of last successful search
  * @i_cno: checkpoint number for GC inode
- * @i_btnode_cache: cached pages of b-tree nodes
+ * @i_assoc_inode: associated inode (B-tree node cache holder or back pointer)
  * @i_dirty: list for connecting dirty files
  * @xattr_sem: semaphore for extended attributes processing
  * @i_bh: buffer contains disk inode
@@ -43,7 +43,7 @@
 	__u64 i_xattr;	/* sector_t ??? */
 	__u32 i_dir_start_lookup;
 	__u64 i_cno;		/* check point number for GC inode */
-	struct address_space i_btnode_cache;
+	struct inode *i_assoc_inode;
 	struct list_head i_dirty;	/* List for connecting dirty files */
 
 #ifdef CONFIG_NILFS_XATTR
@@ -75,13 +75,6 @@
 	return container_of(bmap, struct nilfs_inode_info, i_bmap_data);
 }
 
-static inline struct inode *NILFS_BTNC_I(struct address_space *btnc)
-{
-	struct nilfs_inode_info *ii =
-		container_of(btnc, struct nilfs_inode_info, i_btnode_cache);
-	return &ii->vfs_inode;
-}
-
 /*
  * Dynamic state flags of NILFS on-memory inode (i_state)
  */
@@ -98,6 +91,8 @@
 	NILFS_I_INODE_SYNC,		/* dsync is not allowed for inode */
 	NILFS_I_BMAP,			/* has bmap and btnode_cache */
 	NILFS_I_GCINODE,		/* inode for GC, on memory only */
+	NILFS_I_BTNC,			/* inode for btree node cache */
+	NILFS_I_SHADOW,			/* inode for shadowed page cache */
 };
 
 /*
@@ -121,9 +116,15 @@
 #define NILFS_FIRST_INO(sb) (((struct the_nilfs *)sb->s_fs_info)->ns_first_ino)
 
 #define NILFS_MDT_INODE(sb, ino) \
-	((ino) < NILFS_FIRST_INO(sb) && (NILFS_MDT_INO_BITS & BIT(ino)))
+	((ino) < NILFS_USER_INO && (NILFS_MDT_INO_BITS & BIT(ino)))
 #define NILFS_VALID_INODE(sb, ino) \
-	((ino) >= NILFS_FIRST_INO(sb) || (NILFS_SYS_INO_BITS & BIT(ino)))
+	((ino) >= NILFS_FIRST_INO(sb) ||				\
+	 ((ino) < NILFS_USER_INO && (NILFS_SYS_INO_BITS & BIT(ino))))
+
+#define NILFS_PRIVATE_INODE(ino) ({					\
+	ino_t __ino = (ino);						\
+	((__ino) < NILFS_USER_INO && (__ino) != NILFS_ROOT_INO &&	\
+	 (__ino) != NILFS_SKETCH_INO); })
 
 /**
  * struct nilfs_transaction_info: context information for synchronization
@@ -203,6 +204,9 @@
 
 static inline int nilfs_init_acl(struct inode *inode, struct inode *dir)
 {
+	if (S_ISLNK(inode->i_mode))
+		return 0;
+
 	inode->i_mode &= ~current_umask();
 	return 0;
 }
@@ -229,15 +233,21 @@
 
 /* dir.c */
 extern int nilfs_add_link(struct dentry *, struct inode *);
-extern ino_t nilfs_inode_by_name(struct inode *, const struct qstr *);
+int nilfs_inode_by_name(struct inode *dir, const struct qstr *qstr, ino_t *ino);
 extern int nilfs_make_empty(struct inode *, struct inode *);
 extern struct nilfs_dir_entry *
 nilfs_find_entry(struct inode *, const struct qstr *, struct page **);
 extern int nilfs_delete_entry(struct nilfs_dir_entry *, struct page *);
 extern int nilfs_empty_dir(struct inode *);
 extern struct nilfs_dir_entry *nilfs_dotdot(struct inode *, struct page **);
-extern void nilfs_set_link(struct inode *, struct nilfs_dir_entry *,
-			   struct page *, struct inode *);
+int nilfs_set_link(struct inode *dir, struct nilfs_dir_entry *de,
+		   struct page *page, struct inode *inode);
+
+static inline void nilfs_put_page(struct page *page)
+{
+	kunmap(page);
+	put_page(page);
+}
 
 /* file.c */
 extern int nilfs_sync_file(struct file *, loff_t, loff_t, int);
@@ -267,6 +277,9 @@
 			 unsigned long ino);
 extern struct inode *nilfs_iget_for_gc(struct super_block *sb,
 				       unsigned long ino, __u64 cno);
+int nilfs_attach_btree_node_cache(struct inode *inode);
+void nilfs_detach_btree_node_cache(struct inode *inode);
+struct inode *nilfs_iget_for_shadow(struct inode *inode);
 extern void nilfs_update_inode(struct inode *, struct buffer_head *, int);
 extern void nilfs_truncate(struct inode *);
 extern void nilfs_evict_inode(struct inode *);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/page.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/page.c
@@ -39,7 +39,6 @@
 	first_block = (unsigned long)index << (PAGE_SHIFT - blkbits);
 	bh = nilfs_page_get_nth_block(page, block - first_block);
 
-	touch_buffer(bh);
 	wait_on_buffer(bh);
 	return bh;
 }
@@ -64,6 +63,7 @@
 		put_page(page);
 		return NULL;
 	}
+	bh->b_bdev = inode->i_sb->s_bdev;
 	return bh;
 }
 
@@ -77,7 +77,8 @@
 	const unsigned long clear_bits =
 		(BIT(BH_Uptodate) | BIT(BH_Dirty) | BIT(BH_Mapped) |
 		 BIT(BH_Async_Write) | BIT(BH_NILFS_Volatile) |
-		 BIT(BH_NILFS_Checked) | BIT(BH_NILFS_Redirected));
+		 BIT(BH_NILFS_Checked) | BIT(BH_NILFS_Redirected) |
+		 BIT(BH_Delay));
 
 	lock_buffer(bh);
 	set_mask_bits(&bh->b_state, clear_bits, 0);
@@ -353,9 +354,8 @@
 /**
  * nilfs_clear_dirty_pages - discard dirty pages in address space
  * @mapping: address space with dirty pages for discarding
- * @silent: suppress [true] or print [false] warning messages
  */
-void nilfs_clear_dirty_pages(struct address_space *mapping, bool silent)
+void nilfs_clear_dirty_pages(struct address_space *mapping)
 {
 	struct pagevec pvec;
 	unsigned int i;
@@ -369,7 +369,15 @@
 			struct page *page = pvec.pages[i];
 
 			lock_page(page);
-			nilfs_clear_dirty_page(page, silent);
+
+			/*
+			 * This page may have been removed from the address
+			 * space by truncation or invalidation when the lock
+			 * was acquired.  Skip processing in that case.
+			 */
+			if (likely(page->mapping == mapping))
+				nilfs_clear_dirty_page(page);
+
 			unlock_page(page);
 		}
 		pagevec_release(&pvec);
@@ -380,42 +388,54 @@
 /**
  * nilfs_clear_dirty_page - discard dirty page
  * @page: dirty page that will be discarded
- * @silent: suppress [true] or print [false] warning messages
+ *
+ * nilfs_clear_dirty_page() clears working states including dirty state for
+ * the page and its buffers.  If the page has buffers, clear only if it is
+ * confirmed that none of the buffer heads are busy (none have valid
+ * references and none are locked).
  */
-void nilfs_clear_dirty_page(struct page *page, bool silent)
+void nilfs_clear_dirty_page(struct page *page)
 {
-	struct inode *inode = page->mapping->host;
-	struct super_block *sb = inode->i_sb;
-
 	BUG_ON(!PageLocked(page));
 
-	if (!silent)
-		nilfs_warn(sb, "discard dirty page: offset=%lld, ino=%lu",
-			   page_offset(page), inode->i_ino);
-
-	ClearPageUptodate(page);
-	ClearPageMappedToDisk(page);
-
 	if (page_has_buffers(page)) {
-		struct buffer_head *bh, *head;
+		struct buffer_head *bh, *head = page_buffers(page);
 		const unsigned long clear_bits =
 			(BIT(BH_Uptodate) | BIT(BH_Dirty) | BIT(BH_Mapped) |
 			 BIT(BH_Async_Write) | BIT(BH_NILFS_Volatile) |
-			 BIT(BH_NILFS_Checked) | BIT(BH_NILFS_Redirected));
+			 BIT(BH_NILFS_Checked) | BIT(BH_NILFS_Redirected) |
+			 BIT(BH_Delay));
+		bool busy, invalidated = false;
+
+recheck_buffers:
+		busy = false;
+		bh = head;
+		do {
+			if (atomic_read(&bh->b_count) | buffer_locked(bh)) {
+				busy = true;
+				break;
+			}
+		} while (bh = bh->b_this_page, bh != head);
 
-		bh = head = page_buffers(page);
+		if (busy) {
+			if (invalidated)
+				return;
+			invalidate_bh_lrus();
+			invalidated = true;
+			goto recheck_buffers;
+		}
+
+		bh = head;
 		do {
 			lock_buffer(bh);
-			if (!silent)
-				nilfs_warn(sb,
-					   "discard dirty block: blocknr=%llu, size=%zu",
-					   (u64)bh->b_blocknr, bh->b_size);
-
 			set_mask_bits(&bh->b_state, clear_bits, 0);
 			unlock_buffer(bh);
 		} while (bh = bh->b_this_page, bh != head);
 	}
 
+	ClearPageUptodate(page);
+	ClearPageMappedToDisk(page);
+	ClearPageChecked(page);
 	__nilfs_clear_page_dirty(page);
 }
 
@@ -448,10 +468,9 @@
 /*
  * NILFS2 needs clear_page_dirty() in the following two cases:
  *
- * 1) For B-tree node pages and data pages of the dat/gcdat, NILFS2 clears
- *    page dirty flags when it copies back pages from the shadow cache
- *    (gcdat->{i_mapping,i_btnode_cache}) to its original cache
- *    (dat->{i_mapping,i_btnode_cache}).
+ * 1) For B-tree node pages and data pages of DAT file, NILFS2 clears dirty
+ *    flag of pages when it copies back pages from shadow cache to the
+ *    original cache.
  *
  * 2) Some B-tree operations like insertion or deletion may dispose buffers
  *    in dirty state, and this needs to cancel the dirty state of their pages.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/page.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/page.h
@@ -41,8 +41,8 @@
 
 int nilfs_copy_dirty_pages(struct address_space *, struct address_space *);
 void nilfs_copy_back_pages(struct address_space *, struct address_space *);
-void nilfs_clear_dirty_page(struct page *, bool);
-void nilfs_clear_dirty_pages(struct address_space *, bool);
+void nilfs_clear_dirty_page(struct page *page);
+void nilfs_clear_dirty_pages(struct address_space *mapping);
 void nilfs_mapping_init(struct address_space *mapping, struct inode *inode);
 unsigned int nilfs_page_count_clean_buffers(struct page *, unsigned int,
 					    unsigned int);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/recovery.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/recovery.c
@@ -472,9 +472,10 @@
 
 static int nilfs_recovery_copy_block(struct the_nilfs *nilfs,
 				     struct nilfs_recovery_block *rb,
-				     struct page *page)
+				     loff_t pos, struct page *page)
 {
 	struct buffer_head *bh_org;
+	size_t from = pos & ~PAGE_MASK;
 	void *kaddr;
 
 	bh_org = __bread(nilfs->ns_bdev, rb->blocknr, nilfs->ns_blocksize);
@@ -482,7 +483,7 @@
 		return -EIO;
 
 	kaddr = kmap_atomic(page);
-	memcpy(kaddr + bh_offset(bh_org), bh_org->b_data, bh_org->b_size);
+	memcpy(kaddr + from, bh_org->b_data, bh_org->b_size);
 	kunmap_atomic(kaddr);
 	brelse(bh_org);
 	return 0;
@@ -521,7 +522,7 @@
 			goto failed_inode;
 		}
 
-		err = nilfs_recovery_copy_block(nilfs, rb, page);
+		err = nilfs_recovery_copy_block(nilfs, rb, pos, page);
 		if (unlikely(err))
 			goto failed_page;
 
@@ -708,6 +709,33 @@
 }
 
 /**
+ * nilfs_abort_roll_forward - cleaning up after a failed rollforward recovery
+ * @nilfs: nilfs object
+ */
+static void nilfs_abort_roll_forward(struct the_nilfs *nilfs)
+{
+	struct nilfs_inode_info *ii, *n;
+	LIST_HEAD(head);
+
+	/* Abandon inodes that have read recovery data */
+	spin_lock(&nilfs->ns_inode_lock);
+	list_splice_init(&nilfs->ns_dirty_files, &head);
+	spin_unlock(&nilfs->ns_inode_lock);
+	if (list_empty(&head))
+		return;
+
+	set_nilfs_purging(nilfs);
+	list_for_each_entry_safe(ii, n, &head, i_dirty) {
+		spin_lock(&nilfs->ns_inode_lock);
+		list_del_init(&ii->i_dirty);
+		spin_unlock(&nilfs->ns_inode_lock);
+
+		iput(&ii->vfs_inode);
+	}
+	clear_nilfs_purging(nilfs);
+}
+
+/**
  * nilfs_salvage_orphan_logs - salvage logs written after the latest checkpoint
  * @nilfs: nilfs object
  * @sb: super block instance
@@ -765,15 +793,19 @@
 		if (unlikely(err)) {
 			nilfs_err(sb, "error %d writing segment for recovery",
 				  err);
-			goto failed;
+			goto put_root;
 		}
 
 		nilfs_finish_roll_forward(nilfs, ri);
 	}
 
- failed:
+put_root:
 	nilfs_put_root(root);
 	return err;
+
+failed:
+	nilfs_abort_roll_forward(nilfs);
+	goto put_root;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/segbuf.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/segbuf.c
@@ -101,6 +101,12 @@
 	if (unlikely(!bh))
 		return -ENOMEM;
 
+	lock_buffer(bh);
+	if (!buffer_uptodate(bh)) {
+		memset(bh->b_data, 0, bh->b_size);
+		set_buffer_uptodate(bh);
+	}
+	unlock_buffer(bh);
 	nilfs_segbuf_add_segsum_buffer(segbuf, bh);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/segment.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/segment.c
@@ -136,7 +136,7 @@
 
 #define nilfs_cnt32_ge(a, b)   \
 	(typecheck(__u32, a) && typecheck(__u32, b) && \
-	 ((__s32)(a) - (__s32)(b) >= 0))
+	 ((__s32)((a) - (b)) >= 0))
 
 static int nilfs_prepare_segment_lock(struct super_block *sb,
 				      struct nilfs_transaction_info *ti)
@@ -317,7 +317,7 @@
 	struct the_nilfs *nilfs = sb->s_fs_info;
 	struct nilfs_sc_info *sci = nilfs->ns_writer;
 
-	if (!sci || !sci->sc_flush_request)
+	if (sb_rdonly(sb) || unlikely(!sci) || !sci->sc_flush_request)
 		return;
 
 	set_bit(NILFS_SC_PRIOR_FLUSH, &sci->sc_flags);
@@ -430,6 +430,23 @@
 	return 0;
 }
 
+/**
+ * nilfs_segctor_zeropad_segsum - zero pad the rest of the segment summary area
+ * @sci: segment constructor object
+ *
+ * nilfs_segctor_zeropad_segsum() zero-fills unallocated space at the end of
+ * the current segment summary block.
+ */
+static void nilfs_segctor_zeropad_segsum(struct nilfs_sc_info *sci)
+{
+	struct nilfs_segsum_pointer *ssp;
+
+	ssp = sci->sc_blk_cnt > 0 ? &sci->sc_binfo_ptr : &sci->sc_finfo_ptr;
+	if (ssp->offset < ssp->bh->b_size)
+		memset(ssp->bh->b_data + ssp->offset, 0,
+		       ssp->bh->b_size - ssp->offset);
+}
+
 static int nilfs_segctor_feed_segment(struct nilfs_sc_info *sci)
 {
 	sci->sc_nblk_this_inc += sci->sc_curseg->sb_sum.nblocks;
@@ -438,6 +455,7 @@
 				* The current segment is filled up
 				* (internal code)
 				*/
+	nilfs_segctor_zeropad_segsum(sci);
 	sci->sc_curseg = NILFS_NEXT_SEGBUF(sci->sc_curseg);
 	return nilfs_segctor_reset_segment_buffer(sci);
 }
@@ -542,6 +560,7 @@
 		goto retry;
 	}
 	if (unlikely(required)) {
+		nilfs_segctor_zeropad_segsum(sci);
 		err = nilfs_segbuf_extend_segsum(segbuf);
 		if (unlikely(err))
 			goto failed;
@@ -706,9 +725,13 @@
 		struct page *page = pvec.pages[i];
 
 		lock_page(page);
+		if (unlikely(page->mapping != mapping)) {
+			/* Exclude pages removed from the address space */
+			unlock_page(page);
+			continue;
+		}
 		if (!page_has_buffers(page))
 			create_empty_buffers(page, i_blocksize(inode), 0);
-		unlock_page(page);
 
 		bh = head = page_buffers(page);
 		do {
@@ -718,11 +741,14 @@
 			list_add_tail(&bh->b_assoc_buffers, listp);
 			ndirties++;
 			if (unlikely(ndirties >= nlimit)) {
+				unlock_page(page);
 				pagevec_release(&pvec);
 				cond_resched();
 				return ndirties;
 			}
 		} while (bh = bh->b_this_page, bh != head);
+
+		unlock_page(page);
 	}
 	pagevec_release(&pvec);
 	cond_resched();
@@ -733,15 +759,18 @@
 					    struct list_head *listp)
 {
 	struct nilfs_inode_info *ii = NILFS_I(inode);
-	struct address_space *mapping = &ii->i_btnode_cache;
+	struct inode *btnc_inode = ii->i_assoc_inode;
 	struct pagevec pvec;
 	struct buffer_head *bh, *head;
 	unsigned int i;
 	pgoff_t index = 0;
 
+	if (!btnc_inode)
+		return;
+
 	pagevec_init(&pvec);
 
-	while (pagevec_lookup_tag(&pvec, mapping, &index,
+	while (pagevec_lookup_tag(&pvec, btnc_inode->i_mapping, &index,
 					PAGECACHE_TAG_DIRTY)) {
 		for (i = 0; i < pagevec_count(&pvec); i++) {
 			bh = head = page_buffers(pvec.pages[i]);
@@ -872,9 +901,11 @@
 		nilfs_mdt_mark_dirty(nilfs->ns_cpfile);
 		nilfs_cpfile_put_checkpoint(
 			nilfs->ns_cpfile, nilfs->ns_cno, bh_cp);
-	} else
-		WARN_ON(err == -EINVAL || err == -ENOENT);
-
+	} else if (err == -EINVAL || err == -ENOENT) {
+		nilfs_error(sci->sc_super,
+			    "checkpoint creation failed due to metadata corruption.");
+		err = -EIO;
+	}
 	return err;
 }
 
@@ -888,7 +919,11 @@
 	err = nilfs_cpfile_get_checkpoint(nilfs->ns_cpfile, nilfs->ns_cno, 0,
 					  &raw_cp, &bh_cp);
 	if (unlikely(err)) {
-		WARN_ON(err == -EINVAL || err == -ENOENT);
+		if (err == -EINVAL || err == -ENOENT) {
+			nilfs_error(sci->sc_super,
+				    "checkpoint finalization failed due to metadata corruption.");
+			err = -EIO;
+		}
 		goto failed_ibh;
 	}
 	raw_cp->cp_snapshot_list.ssl_next = 0;
@@ -951,10 +986,13 @@
 	unsigned int isz, srsz;
 
 	bh_sr = NILFS_LAST_SEGBUF(&sci->sc_segbufs)->sb_super_root;
+
+	lock_buffer(bh_sr);
 	raw_sr = (struct nilfs_super_root *)bh_sr->b_data;
 	isz = nilfs->ns_inode_size;
 	srsz = NILFS_SR_BYTES(isz);
 
+	raw_sr->sr_sum = 0;  /* Ensure initialization within this update */
 	raw_sr->sr_bytes = cpu_to_le16(srsz);
 	raw_sr->sr_nongc_ctime
 		= cpu_to_le64(nilfs_doing_gc() ?
@@ -968,6 +1006,8 @@
 	nilfs_write_inode_common(nilfs->ns_sufile, (void *)raw_sr +
 				 NILFS_SR_SUFILE_OFFSET(isz), 1);
 	memset((void *)raw_sr + srsz, 0, nilfs->ns_blocksize - srsz);
+	set_buffer_uptodate(bh_sr);
+	unlock_buffer(bh_sr);
 }
 
 static void nilfs_redirty_inodes(struct list_head *head)
@@ -1522,6 +1562,7 @@
 		nadd = min_t(int, nadd << 1, SC_MAX_SEGDELTA);
 		sci->sc_stage = prev_stage;
 	}
+	nilfs_segctor_zeropad_segsum(sci);
 	nilfs_segctor_truncate_segments(sci, sci->sc_curseg, nilfs->ns_sufile);
 	return 0;
 
@@ -1653,6 +1694,7 @@
 			if (bh->b_page != bd_page) {
 				if (bd_page) {
 					lock_page(bd_page);
+					wait_on_page_writeback(bd_page);
 					clear_page_dirty_for_io(bd_page);
 					set_page_writeback(bd_page);
 					unlock_page(bd_page);
@@ -1663,10 +1705,10 @@
 
 		list_for_each_entry(bh, &segbuf->sb_payload_buffers,
 				    b_assoc_buffers) {
-			set_buffer_async_write(bh);
 			if (bh == segbuf->sb_super_root) {
 				if (bh->b_page != bd_page) {
 					lock_page(bd_page);
+					wait_on_page_writeback(bd_page);
 					clear_page_dirty_for_io(bd_page);
 					set_page_writeback(bd_page);
 					unlock_page(bd_page);
@@ -1674,6 +1716,7 @@
 				}
 				break;
 			}
+			set_buffer_async_write(bh);
 			if (bh->b_page != fs_page) {
 				nilfs_begin_page_io(fs_page);
 				fs_page = bh->b_page;
@@ -1682,6 +1725,7 @@
 	}
 	if (bd_page) {
 		lock_page(bd_page);
+		wait_on_page_writeback(bd_page);
 		clear_page_dirty_for_io(bd_page);
 		set_page_writeback(bd_page);
 		unlock_page(bd_page);
@@ -1749,6 +1793,7 @@
 	list_for_each_entry(segbuf, logs, sb_list) {
 		list_for_each_entry(bh, &segbuf->sb_segsum_buffers,
 				    b_assoc_buffers) {
+			clear_buffer_uptodate(bh);
 			if (bh->b_page != bd_page) {
 				if (bd_page)
 					end_page_writeback(bd_page);
@@ -1758,14 +1803,15 @@
 
 		list_for_each_entry(bh, &segbuf->sb_payload_buffers,
 				    b_assoc_buffers) {
-			clear_buffer_async_write(bh);
 			if (bh == segbuf->sb_super_root) {
+				clear_buffer_uptodate(bh);
 				if (bh->b_page != bd_page) {
 					end_page_writeback(bd_page);
 					bd_page = bh->b_page;
 				}
 				break;
 			}
+			clear_buffer_async_write(bh);
 			if (bh->b_page != fs_page) {
 				nilfs_end_page_io(fs_page, err);
 				fs_page = bh->b_page;
@@ -1789,6 +1835,9 @@
 	nilfs_abort_logs(&logs, ret ? : err);
 
 	list_splice_tail_init(&sci->sc_segbufs, &logs);
+	if (list_empty(&logs))
+		return; /* if the first segment buffer preparation failed */
+
 	nilfs_cancel_segusage(&logs, nilfs->ns_sufile);
 	nilfs_free_incomplete_logs(&logs, nilfs);
 
@@ -1853,8 +1902,9 @@
 				 BIT(BH_Delay) | BIT(BH_NILFS_Volatile) |
 				 BIT(BH_NILFS_Redirected));
 
-			set_mask_bits(&bh->b_state, clear_bits, set_bits);
 			if (bh == segbuf->sb_super_root) {
+				set_buffer_uptodate(bh);
+				clear_buffer_dirty(bh);
 				if (bh->b_page != bd_page) {
 					end_page_writeback(bd_page);
 					bd_page = bh->b_page;
@@ -1862,6 +1912,7 @@
 				update_sr = true;
 				break;
 			}
+			set_mask_bits(&bh->b_state, clear_bits, set_bits);
 			if (bh->b_page != fs_page) {
 				nilfs_end_page_io(fs_page, 0);
 				fs_page = bh->b_page;
@@ -2010,6 +2061,9 @@
 	struct the_nilfs *nilfs = sci->sc_super->s_fs_info;
 	int err;
 
+	if (sb_rdonly(sci->sc_super))
+		return -EROFS;
+
 	nilfs_sc_cstage_set(sci, NILFS_ST_INIT);
 	sci->sc_cno = nilfs->ns_cno;
 
@@ -2028,7 +2082,7 @@
 
 		err = nilfs_segctor_begin_construction(sci, nilfs);
 		if (unlikely(err))
-			goto out;
+			goto failed;
 
 		/* Update time stamp */
 		sci->sc_seg_ctime = ktime_get_real_seconds();
@@ -2091,10 +2145,9 @@
 	return err;
 
  failed_to_write:
-	if (sci->sc_stage.flags & NILFS_CF_IFILE_STARTED)
-		nilfs_redirty_inodes(&sci->sc_dirty_files);
-
  failed:
+	if (mode == SC_LSEG_SR && nilfs_sc_cstage_get(sci) >= NILFS_ST_IFILE)
+		nilfs_redirty_inodes(&sci->sc_dirty_files);
 	if (nilfs_doing_gc())
 		nilfs_redirty_inodes(&sci->sc_gc_inodes);
 	nilfs_segctor_abort_construction(sci, nilfs, err);
@@ -2113,8 +2166,10 @@
 {
 	spin_lock(&sci->sc_state_lock);
 	if (!(sci->sc_state & NILFS_SEGCTOR_COMMIT)) {
-		sci->sc_timer.expires = jiffies + sci->sc_interval;
-		add_timer(&sci->sc_timer);
+		if (sci->sc_task) {
+			sci->sc_timer.expires = jiffies + sci->sc_interval;
+			add_timer(&sci->sc_timer);
+		}
 		sci->sc_state |= NILFS_SEGCTOR_COMMIT;
 	}
 	spin_unlock(&sci->sc_state_lock);
@@ -2161,19 +2216,36 @@
 	struct nilfs_segctor_wait_request wait_req;
 	int err = 0;
 
-	spin_lock(&sci->sc_state_lock);
 	init_wait(&wait_req.wq);
 	wait_req.err = 0;
 	atomic_set(&wait_req.done, 0);
+	init_waitqueue_entry(&wait_req.wq, current);
+
+	/*
+	 * To prevent a race issue where completion notifications from the
+	 * log writer thread are missed, increment the request sequence count
+	 * "sc_seq_request" and insert a wait queue entry using the current
+	 * sequence number into the "sc_wait_request" queue at the same time
+	 * within the lock section of "sc_state_lock".
+	 */
+	spin_lock(&sci->sc_state_lock);
 	wait_req.seq = ++sci->sc_seq_request;
+	add_wait_queue(&sci->sc_wait_request, &wait_req.wq);
 	spin_unlock(&sci->sc_state_lock);
 
-	init_waitqueue_entry(&wait_req.wq, current);
-	add_wait_queue(&sci->sc_wait_request, &wait_req.wq);
-	set_current_state(TASK_INTERRUPTIBLE);
 	wake_up(&sci->sc_wait_daemon);
 
 	for (;;) {
+		set_current_state(TASK_INTERRUPTIBLE);
+
+		/*
+		 * Synchronize only while the log writer thread is alive.
+		 * Leave flushing out after the log writer thread exits to
+		 * the cleanup work in nilfs_segctor_destroy().
+		 */
+		if (!sci->sc_task)
+			break;
+
 		if (atomic_read(&wait_req.done)) {
 			err = wait_req.err;
 			break;
@@ -2189,7 +2261,7 @@
 	return err;
 }
 
-static void nilfs_segctor_wakeup(struct nilfs_sc_info *sci, int err)
+static void nilfs_segctor_wakeup(struct nilfs_sc_info *sci, int err, bool force)
 {
 	struct nilfs_segctor_wait_request *wrq, *n;
 	unsigned long flags;
@@ -2197,7 +2269,7 @@
 	spin_lock_irqsave(&sci->sc_wait_request.lock, flags);
 	list_for_each_entry_safe(wrq, n, &sci->sc_wait_request.head, wq.entry) {
 		if (!atomic_read(&wrq->done) &&
-		    nilfs_cnt32_ge(sci->sc_seq_done, wrq->seq)) {
+		    (force || nilfs_cnt32_ge(sci->sc_seq_done, wrq->seq))) {
 			wrq->err = err;
 			atomic_set(&wrq->done, 1);
 		}
@@ -2234,7 +2306,7 @@
 	struct nilfs_transaction_info *ti;
 	int err;
 
-	if (!sci)
+	if (sb_rdonly(sb) || unlikely(!sci))
 		return -EROFS;
 
 	/* A call inside transactions causes a deadlock. */
@@ -2273,7 +2345,7 @@
 	struct nilfs_transaction_info ti;
 	int err = 0;
 
-	if (!sci)
+	if (sb_rdonly(sb) || unlikely(!sci))
 		return -EROFS;
 
 	nilfs_transaction_lock(sb, &ti, 0);
@@ -2317,10 +2389,21 @@
  */
 static void nilfs_segctor_accept(struct nilfs_sc_info *sci)
 {
+	bool thread_is_alive;
+
 	spin_lock(&sci->sc_state_lock);
 	sci->sc_seq_accepted = sci->sc_seq_request;
+	thread_is_alive = (bool)sci->sc_task;
 	spin_unlock(&sci->sc_state_lock);
-	del_timer_sync(&sci->sc_timer);
+
+	/*
+	 * This function does not race with the log writer thread's
+	 * termination.  Therefore, deleting sc_timer, which should not be
+	 * done after the log writer thread exits, can be done safely outside
+	 * the area protected by sc_state_lock.
+	 */
+	if (thread_is_alive)
+		del_timer_sync(&sci->sc_timer);
 }
 
 /**
@@ -2337,7 +2420,7 @@
 	if (mode == SC_LSEG_SR) {
 		sci->sc_state &= ~NILFS_SEGCTOR_COMMIT;
 		sci->sc_seq_done = sci->sc_seq_accepted;
-		nilfs_segctor_wakeup(sci, err);
+		nilfs_segctor_wakeup(sci, err, false);
 		sci->sc_flush_request = 0;
 	} else {
 		if (mode == SC_FLUSH_FILE)
@@ -2346,7 +2429,7 @@
 			sci->sc_flush_request &= ~FLUSH_DAT_BIT;
 
 		/* re-enable timer if checkpoint creation was not done */
-		if ((sci->sc_state & NILFS_SEGCTOR_COMMIT) &&
+		if ((sci->sc_state & NILFS_SEGCTOR_COMMIT) && sci->sc_task &&
 		    time_before(jiffies, sci->sc_timer.expires))
 			add_timer(&sci->sc_timer);
 	}
@@ -2410,7 +2493,7 @@
 			continue;
 		list_del_init(&ii->i_dirty);
 		truncate_inode_pages(&ii->vfs_inode.i_data, 0);
-		nilfs_btnode_cache_clear(&ii->i_btnode_cache);
+		nilfs_btnode_cache_clear(ii->i_assoc_inode->i_mapping);
 		iput(&ii->vfs_inode);
 	}
 }
@@ -2536,6 +2619,7 @@
 	int timeout = 0;
 
 	sci->sc_timer_task = current;
+	timer_setup(&sci->sc_timer, nilfs_construction_timeout, 0);
 
 	/* start sync. */
 	sci->sc_task = current;
@@ -2600,11 +2684,11 @@
 	goto loop;
 
  end_thread:
-	spin_unlock(&sci->sc_state_lock);
-
 	/* end sync. */
 	sci->sc_task = NULL;
+	del_timer_sync(&sci->sc_timer);
 	wake_up(&sci->sc_wait_task); /* for nilfs_segctor_kill_thread() */
+	spin_unlock(&sci->sc_state_lock);
 	return 0;
 }
 
@@ -2666,7 +2750,6 @@
 	INIT_LIST_HEAD(&sci->sc_gc_inodes);
 	INIT_LIST_HEAD(&sci->sc_iput_queue);
 	INIT_WORK(&sci->sc_iput_work, nilfs_iput_work_func);
-	timer_setup(&sci->sc_timer, nilfs_construction_timeout, 0);
 
 	sci->sc_interval = HZ * NILFS_SC_DEFAULT_TIMEOUT;
 	sci->sc_mjcp_freq = HZ * NILFS_SC_DEFAULT_SR_FREQ;
@@ -2696,7 +2779,7 @@
 
 		flush_work(&sci->sc_iput_work);
 
-	} while (ret && retrycount-- > 0);
+	} while (ret && ret != -EROFS && retrycount-- > 0);
 }
 
 /**
@@ -2720,6 +2803,13 @@
 		|| sci->sc_seq_request != sci->sc_seq_done);
 	spin_unlock(&sci->sc_state_lock);
 
+	/*
+	 * Forcibly wake up tasks waiting in nilfs_segctor_sync(), which can
+	 * be called from delayed iput() via nilfs_evict_inode() and can race
+	 * with the above log writer thread termination.
+	 */
+	nilfs_segctor_wakeup(sci, 0, true);
+
 	if (flush_work(&sci->sc_iput_work))
 		flag = true;
 
@@ -2745,7 +2835,6 @@
 
 	down_write(&nilfs->ns_segctor_sem);
 
-	del_timer_sync(&sci->sc_timer);
 	kfree(sci);
 }
 
@@ -2769,11 +2858,12 @@
 
 	if (nilfs->ns_writer) {
 		/*
-		 * This happens if the filesystem was remounted
-		 * read/write after nilfs_error degenerated it into a
-		 * read-only mount.
+		 * This happens if the filesystem is made read-only by
+		 * __nilfs_error or nilfs_remount and then remounted
+		 * read/write.  In these cases, reuse the existing
+		 * writer.
 		 */
-		nilfs_detach_log_writer(sb);
+		return 0;
 	}
 
 	nilfs->ns_writer = nilfs_segctor_new(sb, root);
@@ -2783,10 +2873,9 @@
 	inode_attach_wb(nilfs->ns_bdev->bd_inode, NULL);
 
 	err = nilfs_segctor_start_thread(nilfs->ns_writer);
-	if (err) {
-		kfree(nilfs->ns_writer);
-		nilfs->ns_writer = NULL;
-	}
+	if (unlikely(err))
+		nilfs_detach_log_writer(sb);
+
 	return err;
 }
 
@@ -2807,6 +2896,7 @@
 		nilfs_segctor_destroy(nilfs->ns_writer);
 		nilfs->ns_writer = NULL;
 	}
+	set_nilfs_purging(nilfs);
 
 	/* Force to free the list of dirty files */
 	spin_lock(&nilfs->ns_inode_lock);
@@ -2819,4 +2909,5 @@
 	up_write(&nilfs->ns_segctor_sem);
 
 	nilfs_dispose_list(nilfs, &garbage_list, 1);
+	clear_nilfs_purging(nilfs);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/sufile.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/sufile.c
@@ -495,14 +495,45 @@
 int nilfs_sufile_mark_dirty(struct inode *sufile, __u64 segnum)
 {
 	struct buffer_head *bh;
+	void *kaddr;
+	struct nilfs_segment_usage *su;
 	int ret;
 
+	down_write(&NILFS_MDT(sufile)->mi_sem);
 	ret = nilfs_sufile_get_segment_usage_block(sufile, segnum, 0, &bh);
-	if (!ret) {
+	if (ret)
+		goto out_sem;
+
+	kaddr = kmap_atomic(bh->b_page);
+	su = nilfs_sufile_block_get_segment_usage(sufile, segnum, bh, kaddr);
+	if (unlikely(nilfs_segment_usage_error(su))) {
+		struct the_nilfs *nilfs = sufile->i_sb->s_fs_info;
+
+		kunmap_atomic(kaddr);
+		brelse(bh);
+		if (nilfs_segment_is_active(nilfs, segnum)) {
+			nilfs_error(sufile->i_sb,
+				    "active segment %llu is erroneous",
+				    (unsigned long long)segnum);
+		} else {
+			/*
+			 * Segments marked erroneous are never allocated by
+			 * nilfs_sufile_alloc(); only active segments, ie,
+			 * the segments indexed by ns_segnum or ns_nextnum,
+			 * can be erroneous here.
+			 */
+			WARN_ON_ONCE(1);
+		}
+		ret = -EIO;
+	} else {
+		nilfs_segment_usage_set_dirty(su);
+		kunmap_atomic(kaddr);
 		mark_buffer_dirty(bh);
 		nilfs_mdt_mark_dirty(sufile);
 		brelse(bh);
 	}
+out_sem:
+	up_write(&NILFS_MDT(sufile)->mi_sem);
 	return ret;
 }
 
@@ -528,9 +559,14 @@
 
 	kaddr = kmap_atomic(bh->b_page);
 	su = nilfs_sufile_block_get_segment_usage(sufile, segnum, bh, kaddr);
-	WARN_ON(nilfs_segment_usage_error(su));
-	if (modtime)
+	if (modtime) {
+		/*
+		 * Check segusage error and set su_lastmod only when updating
+		 * this entry with a valid timestamp, not for cancellation.
+		 */
+		WARN_ON_ONCE(nilfs_segment_usage_error(su));
 		su->su_lastmod = cpu_to_le64(modtime);
+	}
 	su->su_nblocks = cpu_to_le32(nblocks);
 	kunmap_atomic(kaddr);
 
@@ -771,6 +807,15 @@
 			goto out_header;
 
 		sui->ncleansegs -= nsegs - newnsegs;
+
+		/*
+		 * If the sufile is successfully truncated, immediately adjust
+		 * the segment allocation space while locking the semaphore
+		 * "mi_sem" so that nilfs_sufile_alloc() never allocates
+		 * segments in the truncated space.
+		 */
+		sui->allocmax = newnsegs - 1;
+		sui->allocmin = 0;
 	}
 
 	kaddr = kmap_atomic(header_bh->b_page);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/super.c
@@ -157,7 +157,8 @@
 	ii->i_bh = NULL;
 	ii->i_state = 0;
 	ii->i_cno = 0;
-	nilfs_mapping_init(&ii->i_btnode_cache, &ii->vfs_inode);
+	ii->i_assoc_inode = NULL;
+	ii->i_bmap = &ii->i_bmap_data;
 	return &ii->vfs_inode;
 }
 
@@ -371,10 +372,31 @@
 		goto out;
 	}
 	nsbp = (void *)nsbh->b_data + offset;
-	memset(nsbp, 0, nilfs->ns_blocksize);
 
+	lock_buffer(nsbh);
 	if (sb2i >= 0) {
+		/*
+		 * The position of the second superblock only changes by 4KiB,
+		 * which is larger than the maximum superblock data size
+		 * (= 1KiB), so there is no need to use memmove() to allow
+		 * overlap between source and destination.
+		 */
 		memcpy(nsbp, nilfs->ns_sbp[sb2i], nilfs->ns_sbsize);
+
+		/*
+		 * Zero fill after copy to avoid overwriting in case of move
+		 * within the same block.
+		 */
+		memset(nsbh->b_data, 0, offset);
+		memset((void *)nsbp + nilfs->ns_sbsize, 0,
+		       nsbh->b_size - offset - nilfs->ns_sbsize);
+	} else {
+		memset(nsbh->b_data, 0, nsbh->b_size);
+	}
+	set_buffer_uptodate(nsbh);
+	unlock_buffer(nsbh);
+
+	if (sb2i >= 0) {
 		brelse(nilfs->ns_sbh[sb2i]);
 		nilfs->ns_sbh[sb2i] = nsbh;
 		nilfs->ns_sbp[sb2i] = nsbp;
@@ -408,6 +430,15 @@
 		goto out;
 
 	/*
+	 * Prevent underflow in second superblock position calculation.
+	 * The exact minimum size check is done in nilfs_sufile_resize().
+	 */
+	if (newsize < 4096) {
+		ret = -ENOSPC;
+		goto out;
+	}
+
+	/*
 	 * Write lock is required to protect some functions depending
 	 * on the number of segments, the number of reserved segments,
 	 * and so forth.
@@ -472,6 +503,7 @@
 		up_write(&nilfs->ns_sem);
 	}
 
+	nilfs_sysfs_delete_device_group(nilfs);
 	iput(nilfs->ns_sufile);
 	iput(nilfs->ns_cpfile);
 	iput(nilfs->ns_dat);
@@ -1095,6 +1127,7 @@
 	nilfs_put_root(fsroot);
 
  failed_unload:
+	nilfs_sysfs_delete_device_group(nilfs);
 	iput(nilfs->ns_sufile);
 	iput(nilfs->ns_cpfile);
 	iput(nilfs->ns_dat);
@@ -1132,8 +1165,6 @@
 	if ((bool)(*flags & SB_RDONLY) == sb_rdonly(sb))
 		goto out;
 	if (*flags & SB_RDONLY) {
-		/* Shutting down log writer */
-		nilfs_detach_log_writer(sb);
 		sb->s_flags |= SB_RDONLY;
 
 		/*
@@ -1377,8 +1408,6 @@
 #ifdef CONFIG_NILFS_XATTR
 	init_rwsem(&ii->xattr_sem);
 #endif
-	address_space_init_once(&ii->i_btnode_cache);
-	ii->i_bmap = &ii->i_bmap_data;
 	inode_init_once(&ii->vfs_inode);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/sysfs.c
@@ -95,7 +95,7 @@
 nilfs_snapshot_inodes_count_show(struct nilfs_snapshot_attr *attr,
 				 struct nilfs_root *root, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%llu\n",
+	return sysfs_emit(buf, "%llu\n",
 			(unsigned long long)atomic64_read(&root->inodes_count));
 }
 
@@ -103,7 +103,7 @@
 nilfs_snapshot_blocks_count_show(struct nilfs_snapshot_attr *attr,
 				 struct nilfs_root *root, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%llu\n",
+	return sysfs_emit(buf, "%llu\n",
 			(unsigned long long)atomic64_read(&root->blocks_count));
 }
 
@@ -116,7 +116,7 @@
 nilfs_snapshot_README_show(struct nilfs_snapshot_attr *attr,
 			    struct nilfs_root *root, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, snapshot_readme_str);
+	return sysfs_emit(buf, snapshot_readme_str);
 }
 
 NILFS_SNAPSHOT_RO_ATTR(inodes_count);
@@ -217,7 +217,7 @@
 nilfs_mounted_snapshots_README_show(struct nilfs_mounted_snapshots_attr *attr,
 				    struct the_nilfs *nilfs, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, mounted_snapshots_readme_str);
+	return sysfs_emit(buf, mounted_snapshots_readme_str);
 }
 
 NILFS_MOUNTED_SNAPSHOTS_RO_ATTR(README);
@@ -255,7 +255,7 @@
 
 	ncheckpoints = cpstat.cs_ncps;
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", ncheckpoints);
+	return sysfs_emit(buf, "%llu\n", ncheckpoints);
 }
 
 static ssize_t
@@ -278,7 +278,7 @@
 
 	nsnapshots = cpstat.cs_nsss;
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", nsnapshots);
+	return sysfs_emit(buf, "%llu\n", nsnapshots);
 }
 
 static ssize_t
@@ -292,7 +292,7 @@
 	last_cno = nilfs->ns_last_cno;
 	spin_unlock(&nilfs->ns_last_segment_lock);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", last_cno);
+	return sysfs_emit(buf, "%llu\n", last_cno);
 }
 
 static ssize_t
@@ -306,7 +306,7 @@
 	cno = nilfs->ns_cno;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", cno);
+	return sysfs_emit(buf, "%llu\n", cno);
 }
 
 static const char checkpoints_readme_str[] =
@@ -322,7 +322,7 @@
 nilfs_checkpoints_README_show(struct nilfs_checkpoints_attr *attr,
 				struct the_nilfs *nilfs, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, checkpoints_readme_str);
+	return sysfs_emit(buf, checkpoints_readme_str);
 }
 
 NILFS_CHECKPOINTS_RO_ATTR(checkpoints_number);
@@ -353,7 +353,7 @@
 				     struct the_nilfs *nilfs,
 				     char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%lu\n", nilfs->ns_nsegments);
+	return sysfs_emit(buf, "%lu\n", nilfs->ns_nsegments);
 }
 
 static ssize_t
@@ -361,7 +361,7 @@
 					struct the_nilfs *nilfs,
 					char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%lu\n", nilfs->ns_blocks_per_segment);
+	return sysfs_emit(buf, "%lu\n", nilfs->ns_blocks_per_segment);
 }
 
 static ssize_t
@@ -375,7 +375,7 @@
 	ncleansegs = nilfs_sufile_get_ncleansegs(nilfs->ns_sufile);
 	up_read(&NILFS_MDT(nilfs->ns_dat)->mi_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%lu\n", ncleansegs);
+	return sysfs_emit(buf, "%lu\n", ncleansegs);
 }
 
 static ssize_t
@@ -395,7 +395,7 @@
 		return err;
 	}
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", sustat.ss_ndirtysegs);
+	return sysfs_emit(buf, "%llu\n", sustat.ss_ndirtysegs);
 }
 
 static const char segments_readme_str[] =
@@ -411,7 +411,7 @@
 			    struct the_nilfs *nilfs,
 			    char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, segments_readme_str);
+	return sysfs_emit(buf, segments_readme_str);
 }
 
 NILFS_SEGMENTS_RO_ATTR(segments_number);
@@ -448,7 +448,7 @@
 	last_pseg = nilfs->ns_last_pseg;
 	spin_unlock(&nilfs->ns_last_segment_lock);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n",
+	return sysfs_emit(buf, "%llu\n",
 			(unsigned long long)last_pseg);
 }
 
@@ -463,7 +463,7 @@
 	last_seq = nilfs->ns_last_seq;
 	spin_unlock(&nilfs->ns_last_segment_lock);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", last_seq);
+	return sysfs_emit(buf, "%llu\n", last_seq);
 }
 
 static ssize_t
@@ -477,7 +477,7 @@
 	last_cno = nilfs->ns_last_cno;
 	spin_unlock(&nilfs->ns_last_segment_lock);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", last_cno);
+	return sysfs_emit(buf, "%llu\n", last_cno);
 }
 
 static ssize_t
@@ -491,7 +491,7 @@
 	seg_seq = nilfs->ns_seg_seq;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", seg_seq);
+	return sysfs_emit(buf, "%llu\n", seg_seq);
 }
 
 static ssize_t
@@ -505,7 +505,7 @@
 	segnum = nilfs->ns_segnum;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", segnum);
+	return sysfs_emit(buf, "%llu\n", segnum);
 }
 
 static ssize_t
@@ -519,7 +519,7 @@
 	nextnum = nilfs->ns_nextnum;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", nextnum);
+	return sysfs_emit(buf, "%llu\n", nextnum);
 }
 
 static ssize_t
@@ -533,7 +533,7 @@
 	pseg_offset = nilfs->ns_pseg_offset;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%lu\n", pseg_offset);
+	return sysfs_emit(buf, "%lu\n", pseg_offset);
 }
 
 static ssize_t
@@ -547,7 +547,7 @@
 	cno = nilfs->ns_cno;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", cno);
+	return sysfs_emit(buf, "%llu\n", cno);
 }
 
 static ssize_t
@@ -575,7 +575,7 @@
 	ctime = nilfs->ns_ctime;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", ctime);
+	return sysfs_emit(buf, "%llu\n", ctime);
 }
 
 static ssize_t
@@ -603,7 +603,7 @@
 	nongc_ctime = nilfs->ns_nongc_ctime;
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", nongc_ctime);
+	return sysfs_emit(buf, "%llu\n", nongc_ctime);
 }
 
 static ssize_t
@@ -617,7 +617,7 @@
 	ndirtyblks = atomic_read(&nilfs->ns_ndirtyblks);
 	up_read(&nilfs->ns_segctor_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", ndirtyblks);
+	return sysfs_emit(buf, "%u\n", ndirtyblks);
 }
 
 static const char segctor_readme_str[] =
@@ -654,7 +654,7 @@
 nilfs_segctor_README_show(struct nilfs_segctor_attr *attr,
 			  struct the_nilfs *nilfs, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, segctor_readme_str);
+	return sysfs_emit(buf, segctor_readme_str);
 }
 
 NILFS_SEGCTOR_RO_ATTR(last_pseg_block);
@@ -723,7 +723,7 @@
 	sbwtime = nilfs->ns_sbwtime;
 	up_read(&nilfs->ns_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", sbwtime);
+	return sysfs_emit(buf, "%llu\n", sbwtime);
 }
 
 static ssize_t
@@ -737,7 +737,7 @@
 	sbwcount = nilfs->ns_sbwcount;
 	up_read(&nilfs->ns_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", sbwcount);
+	return sysfs_emit(buf, "%u\n", sbwcount);
 }
 
 static ssize_t
@@ -751,7 +751,7 @@
 	sb_update_freq = nilfs->ns_sb_update_freq;
 	up_read(&nilfs->ns_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%u\n", sb_update_freq);
+	return sysfs_emit(buf, "%u\n", sb_update_freq);
 }
 
 static ssize_t
@@ -799,7 +799,7 @@
 nilfs_superblock_README_show(struct nilfs_superblock_attr *attr,
 				struct the_nilfs *nilfs, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, sb_readme_str);
+	return sysfs_emit(buf, sb_readme_str);
 }
 
 NILFS_SUPERBLOCK_RO_ATTR(sb_write_time);
@@ -830,11 +830,17 @@
 				struct the_nilfs *nilfs,
 				char *buf)
 {
-	struct nilfs_super_block **sbp = nilfs->ns_sbp;
-	u32 major = le32_to_cpu(sbp[0]->s_rev_level);
-	u16 minor = le16_to_cpu(sbp[0]->s_minor_rev_level);
+	struct nilfs_super_block *raw_sb;
+	u32 major;
+	u16 minor;
 
-	return snprintf(buf, PAGE_SIZE, "%d.%d\n", major, minor);
+	down_read(&nilfs->ns_sem);
+	raw_sb = nilfs->ns_sbp[0];
+	major = le32_to_cpu(raw_sb->s_rev_level);
+	minor = le16_to_cpu(raw_sb->s_minor_rev_level);
+	up_read(&nilfs->ns_sem);
+
+	return sysfs_emit(buf, "%d.%d\n", major, minor);
 }
 
 static
@@ -842,7 +848,7 @@
 				 struct the_nilfs *nilfs,
 				 char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%u\n", nilfs->ns_blocksize);
+	return sysfs_emit(buf, "%u\n", nilfs->ns_blocksize);
 }
 
 static
@@ -850,10 +856,15 @@
 				    struct the_nilfs *nilfs,
 				    char *buf)
 {
-	struct nilfs_super_block **sbp = nilfs->ns_sbp;
-	u64 dev_size = le64_to_cpu(sbp[0]->s_dev_size);
+	struct nilfs_super_block *raw_sb;
+	u64 dev_size;
+
+	down_read(&nilfs->ns_sem);
+	raw_sb = nilfs->ns_sbp[0];
+	dev_size = le64_to_cpu(raw_sb->s_dev_size);
+	up_read(&nilfs->ns_sem);
 
-	return snprintf(buf, PAGE_SIZE, "%llu\n", dev_size);
+	return sysfs_emit(buf, "%llu\n", dev_size);
 }
 
 static
@@ -864,7 +875,7 @@
 	sector_t free_blocks = 0;
 
 	nilfs_count_free_blocks(nilfs, &free_blocks);
-	return snprintf(buf, PAGE_SIZE, "%llu\n",
+	return sysfs_emit(buf, "%llu\n",
 			(unsigned long long)free_blocks);
 }
 
@@ -873,9 +884,15 @@
 			    struct the_nilfs *nilfs,
 			    char *buf)
 {
-	struct nilfs_super_block **sbp = nilfs->ns_sbp;
+	struct nilfs_super_block *raw_sb;
+	ssize_t len;
 
-	return snprintf(buf, PAGE_SIZE, "%pUb\n", sbp[0]->s_uuid);
+	down_read(&nilfs->ns_sem);
+	raw_sb = nilfs->ns_sbp[0];
+	len = sysfs_emit(buf, "%pUb\n", raw_sb->s_uuid);
+	up_read(&nilfs->ns_sem);
+
+	return len;
 }
 
 static
@@ -883,10 +900,16 @@
 				    struct the_nilfs *nilfs,
 				    char *buf)
 {
-	struct nilfs_super_block **sbp = nilfs->ns_sbp;
+	struct nilfs_super_block *raw_sb;
+	ssize_t len;
+
+	down_read(&nilfs->ns_sem);
+	raw_sb = nilfs->ns_sbp[0];
+	len = scnprintf(buf, sizeof(raw_sb->s_volume_name), "%s\n",
+			raw_sb->s_volume_name);
+	up_read(&nilfs->ns_sem);
 
-	return scnprintf(buf, sizeof(sbp[0]->s_volume_name), "%s\n",
-			 sbp[0]->s_volume_name);
+	return len;
 }
 
 static const char dev_readme_str[] =
@@ -903,7 +926,7 @@
 				     struct the_nilfs *nilfs,
 				     char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, dev_readme_str);
+	return sysfs_emit(buf, dev_readme_str);
 }
 
 NILFS_DEV_RO_ATTR(revision);
@@ -1047,7 +1070,7 @@
 static ssize_t nilfs_feature_revision_show(struct kobject *kobj,
 					    struct attribute *attr, char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, "%d.%d\n",
+	return sysfs_emit(buf, "%d.%d\n",
 			NILFS_CURRENT_REV, NILFS_MINOR_REV);
 }
 
@@ -1060,7 +1083,7 @@
 					 struct attribute *attr,
 					 char *buf)
 {
-	return snprintf(buf, PAGE_SIZE, features_readme_str);
+	return sysfs_emit(buf, features_readme_str);
 }
 
 NILFS_FEATURE_RO_ATTR(revision);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/the_nilfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/the_nilfs.c
@@ -13,6 +13,7 @@
 #include <linux/blkdev.h>
 #include <linux/backing-dev.h>
 #include <linux/random.h>
+#include <linux/log2.h>
 #include <linux/crc32.h>
 #include "nilfs.h"
 #include "segment.h"
@@ -86,7 +87,6 @@
 {
 	might_sleep();
 	if (nilfs_init(nilfs)) {
-		nilfs_sysfs_delete_device_group(nilfs);
 		brelse(nilfs->ns_sbh[0]);
 		brelse(nilfs->ns_sbh[1]);
 	}
@@ -193,6 +193,34 @@
 }
 
 /**
+ * nilfs_get_blocksize - get block size from raw superblock data
+ * @sb: super block instance
+ * @sbp: superblock raw data buffer
+ * @blocksize: place to store block size
+ *
+ * nilfs_get_blocksize() calculates the block size from the block size
+ * exponent information written in @sbp and stores it in @blocksize,
+ * or aborts with an error message if it's too large.
+ *
+ * Return Value: On success, 0 is returned. If the block size is too
+ * large, -EINVAL is returned.
+ */
+static int nilfs_get_blocksize(struct super_block *sb,
+			       struct nilfs_super_block *sbp, int *blocksize)
+{
+	unsigned int shift_bits = le32_to_cpu(sbp->s_log_block_size);
+
+	if (unlikely(shift_bits >
+		     ilog2(NILFS_MAX_BLOCK_SIZE) - BLOCK_SIZE_BITS)) {
+		nilfs_err(sb, "too large filesystem blocksize: 2 ^ %u KiB",
+			  shift_bits);
+		return -EINVAL;
+	}
+	*blocksize = BLOCK_SIZE << shift_bits;
+	return 0;
+}
+
+/**
  * load_nilfs - load and recover the nilfs
  * @nilfs: the_nilfs structure to be released
  * @sb: super block instance used to recover past segment
@@ -245,11 +273,15 @@
 		nilfs->ns_sbwtime = le64_to_cpu(sbp[0]->s_wtime);
 
 		/* verify consistency between two super blocks */
-		blocksize = BLOCK_SIZE << le32_to_cpu(sbp[0]->s_log_block_size);
+		err = nilfs_get_blocksize(sb, sbp[0], &blocksize);
+		if (err)
+			goto scan_error;
+
 		if (blocksize != nilfs->ns_blocksize) {
 			nilfs_warn(sb,
 				   "blocksize differs between two super blocks (%d != %d)",
 				   blocksize, nilfs->ns_blocksize);
+			err = -EINVAL;
 			goto scan_error;
 		}
 
@@ -272,6 +304,10 @@
 		goto failed;
 	}
 
+	err = nilfs_sysfs_create_device_group(sb);
+	if (unlikely(err))
+		goto sysfs_error;
+
 	if (valid_fs)
 		goto skip_recovery;
 
@@ -333,6 +369,9 @@
 	goto failed;
 
  failed_unload:
+	nilfs_sysfs_delete_device_group(nilfs);
+
+ sysfs_error:
 	iput(nilfs->ns_cpfile);
 	iput(nilfs->ns_sufile);
 	iput(nilfs->ns_dat);
@@ -366,6 +405,18 @@
 				  100));
 }
 
+/**
+ * nilfs_max_segment_count - calculate the maximum number of segments
+ * @nilfs: nilfs object
+ */
+static u64 nilfs_max_segment_count(struct the_nilfs *nilfs)
+{
+	u64 max_count = U64_MAX;
+
+	do_div(max_count, nilfs->ns_blocks_per_segment);
+	return min_t(u64, max_count, ULONG_MAX);
+}
+
 void nilfs_set_nsegments(struct the_nilfs *nilfs, unsigned long nsegs)
 {
 	nilfs->ns_nsegments = nsegs;
@@ -375,6 +426,8 @@
 static int nilfs_store_disk_layout(struct the_nilfs *nilfs,
 				   struct nilfs_super_block *sbp)
 {
+	u64 nsegments, nblocks;
+
 	if (le32_to_cpu(sbp->s_rev_level) < NILFS_MIN_SUPP_REV) {
 		nilfs_err(nilfs->ns_sb,
 			  "unsupported revision (superblock rev.=%d.%d, current rev.=%d.%d). Please check the version of mkfs.nilfs(2).",
@@ -399,6 +452,12 @@
 	}
 
 	nilfs->ns_first_ino = le32_to_cpu(sbp->s_first_ino);
+	if (nilfs->ns_first_ino < NILFS_USER_INO) {
+		nilfs_err(nilfs->ns_sb,
+			  "too small lower limit for non-reserved inode numbers: %u",
+			  nilfs->ns_first_ino);
+		return -EINVAL;
+	}
 
 	nilfs->ns_blocks_per_segment = le32_to_cpu(sbp->s_blocks_per_segment);
 	if (nilfs->ns_blocks_per_segment < NILFS_SEG_MIN_BLOCKS) {
@@ -418,7 +477,35 @@
 		return -EINVAL;
 	}
 
-	nilfs_set_nsegments(nilfs, le64_to_cpu(sbp->s_nsegments));
+	nsegments = le64_to_cpu(sbp->s_nsegments);
+	if (nsegments > nilfs_max_segment_count(nilfs)) {
+		nilfs_err(nilfs->ns_sb,
+			  "segment count %llu exceeds upper limit (%llu segments)",
+			  (unsigned long long)nsegments,
+			  (unsigned long long)nilfs_max_segment_count(nilfs));
+		return -EINVAL;
+	}
+
+	nblocks = (u64)i_size_read(nilfs->ns_sb->s_bdev->bd_inode) >>
+		nilfs->ns_sb->s_blocksize_bits;
+	if (nblocks) {
+		u64 min_block_count = nsegments * nilfs->ns_blocks_per_segment;
+		/*
+		 * To avoid failing to mount early device images without a
+		 * second superblock, exclude that block count from the
+		 * "min_block_count" calculation.
+		 */
+
+		if (nblocks < min_block_count) {
+			nilfs_err(nilfs->ns_sb,
+				  "total number of segment blocks %llu exceeds device size (%llu blocks)",
+				  (unsigned long long)min_block_count,
+				  (unsigned long long)nblocks);
+			return -EINVAL;
+		}
+	}
+
+	nilfs_set_nsegments(nilfs, nsegments);
 	nilfs->ns_crc_seed = le32_to_cpu(sbp->s_crc_seed);
 	return 0;
 }
@@ -443,11 +530,33 @@
 	return crc == le32_to_cpu(sbp->s_sum);
 }
 
-static int nilfs_sb2_bad_offset(struct nilfs_super_block *sbp, u64 offset)
+/**
+ * nilfs_sb2_bad_offset - check the location of the second superblock
+ * @sbp: superblock raw data buffer
+ * @offset: byte offset of second superblock calculated from device size
+ *
+ * nilfs_sb2_bad_offset() checks if the position on the second
+ * superblock is valid or not based on the filesystem parameters
+ * stored in @sbp.  If @offset points to a location within the segment
+ * area, or if the parameters themselves are not normal, it is
+ * determined to be invalid.
+ *
+ * Return Value: true if invalid, false if valid.
+ */
+static bool nilfs_sb2_bad_offset(struct nilfs_super_block *sbp, u64 offset)
 {
-	return offset < ((le64_to_cpu(sbp->s_nsegments) *
-			  le32_to_cpu(sbp->s_blocks_per_segment)) <<
-			 (le32_to_cpu(sbp->s_log_block_size) + 10));
+	unsigned int shift_bits = le32_to_cpu(sbp->s_log_block_size);
+	u32 blocks_per_segment = le32_to_cpu(sbp->s_blocks_per_segment);
+	u64 nsegments = le64_to_cpu(sbp->s_nsegments);
+	u64 index;
+
+	if (blocks_per_segment < NILFS_SEG_MIN_BLOCKS ||
+	    shift_bits > ilog2(NILFS_MAX_BLOCK_SIZE) - BLOCK_SIZE_BITS)
+		return true;
+
+	index = offset >> (shift_bits + BLOCK_SIZE_BITS);
+	do_div(index, blocks_per_segment);
+	return index < nsegments;
 }
 
 static void nilfs_release_super_block(struct the_nilfs *nilfs)
@@ -489,9 +598,15 @@
 {
 	struct nilfs_super_block **sbp = nilfs->ns_sbp;
 	struct buffer_head **sbh = nilfs->ns_sbh;
-	u64 sb2off = NILFS_SB2_OFFSET_BYTES(nilfs->ns_bdev->bd_inode->i_size);
+	u64 sb2off, devsize = nilfs->ns_bdev->bd_inode->i_size;
 	int valid[2], swp = 0;
 
+	if (devsize < NILFS_SEG_MIN_BLOCKS * NILFS_MIN_BLOCK_SIZE + 4096) {
+		nilfs_err(sb, "device size too small");
+		return -EINVAL;
+	}
+	sb2off = NILFS_SB2_OFFSET_BYTES(devsize);
+
 	sbp[0] = nilfs_read_super_block(sb, NILFS_SB_OFFSET_BYTES, blocksize,
 					&sbh[0]);
 	sbp[1] = nilfs_read_super_block(sb, sb2off, blocksize, &sbh[1]);
@@ -586,9 +701,11 @@
 	if (err)
 		goto failed_sbh;
 
-	blocksize = BLOCK_SIZE << le32_to_cpu(sbp->s_log_block_size);
-	if (blocksize < NILFS_MIN_BLOCK_SIZE ||
-	    blocksize > NILFS_MAX_BLOCK_SIZE) {
+	err = nilfs_get_blocksize(sb, sbp, &blocksize);
+	if (err)
+		goto failed_sbh;
+
+	if (blocksize < NILFS_MIN_BLOCK_SIZE) {
 		nilfs_err(sb,
 			  "couldn't mount because of unsupported filesystem blocksize %d",
 			  blocksize);
@@ -606,7 +723,11 @@
 			goto failed_sbh;
 		}
 		nilfs_release_super_block(nilfs);
-		sb_set_blocksize(sb, blocksize);
+		if (!sb_set_blocksize(sb, blocksize)) {
+			nilfs_err(sb, "bad blocksize %d", blocksize);
+			err = -EINVAL;
+			goto out;
+		}
 
 		err = nilfs_load_super_block(nilfs, sb, blocksize, &sbp);
 		if (err)
@@ -634,10 +755,6 @@
 	if (err)
 		goto failed_sbh;
 
-	err = nilfs_sysfs_create_device_group(sb);
-	if (err)
-		goto failed_sbh;
-
 	set_nilfs_init(nilfs);
 	err = 0;
  out:
@@ -690,9 +807,7 @@
 {
 	unsigned long ncleansegs;
 
-	down_read(&NILFS_MDT(nilfs->ns_dat)->mi_sem);
 	ncleansegs = nilfs_sufile_get_ncleansegs(nilfs->ns_sufile);
-	up_read(&NILFS_MDT(nilfs->ns_dat)->mi_sem);
 	*nblocks = (sector_t)ncleansegs * nilfs->ns_blocks_per_segment;
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nilfs2/the_nilfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/nilfs2/the_nilfs.h
@@ -29,6 +29,7 @@
 	THE_NILFS_DISCONTINUED,	/* 'next' pointer chain has broken */
 	THE_NILFS_GC_RUNNING,	/* gc process is running */
 	THE_NILFS_SB_DIRTY,	/* super block is dirty */
+	THE_NILFS_PURGING,	/* disposing dirty files for cleanup */
 };
 
 /**
@@ -181,7 +182,7 @@
 	unsigned long		ns_nrsvsegs;
 	unsigned long		ns_first_data_block;
 	int			ns_inode_size;
-	int			ns_first_ino;
+	unsigned int		ns_first_ino;
 	u32			ns_crc_seed;
 
 	/* /sys/fs/<nilfs>/<device> */
@@ -208,6 +209,7 @@
 THE_NILFS_FNS(DISCONTINUED, discontinued)
 THE_NILFS_FNS(GC_RUNNING, gc_running)
 THE_NILFS_FNS(SB_DIRTY, sb_dirty)
+THE_NILFS_FNS(PURGING, purging)
 
 /*
  * Mount option operations
--- linux-xilinx-zynqmp-5.15.0.orig/fs/nls/nls_base.c
+++ linux-xilinx-zynqmp-5.15.0/fs/nls/nls_base.c
@@ -272,7 +272,7 @@
 	return -EINVAL;
 }
 
-static struct nls_table *find_nls(char *charset)
+static struct nls_table *find_nls(const char *charset)
 {
 	struct nls_table *nls;
 	spin_lock(&nls_lock);
@@ -288,7 +288,7 @@
 	return nls;
 }
 
-struct nls_table *load_nls(char *charset)
+struct nls_table *load_nls(const char *charset)
 {
 	return try_then_request_module(find_nls(charset), "nls_%s", charset);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/dnotify/dnotify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/dnotify/dnotify.c
@@ -150,7 +150,7 @@
 		return;
 	dn_mark = container_of(fsn_mark, struct dnotify_mark, fsn_mark);
 
-	mutex_lock(&dnotify_group->mark_mutex);
+	fsnotify_group_lock(dnotify_group);
 
 	spin_lock(&fsn_mark->lock);
 	prev = &dn_mark->dn;
@@ -173,7 +173,7 @@
 		free = true;
 	}
 
-	mutex_unlock(&dnotify_group->mark_mutex);
+	fsnotify_group_unlock(dnotify_group);
 
 	if (free)
 		fsnotify_free_mark(fsn_mark);
@@ -196,7 +196,7 @@
 	if (arg & DN_ATTRIB)
 		new_mask |= FS_ATTRIB;
 	if (arg & DN_RENAME)
-		new_mask |= FS_DN_RENAME;
+		new_mask |= FS_RENAME;
 	if (arg & DN_CREATE)
 		new_mask |= (FS_CREATE | FS_MOVED_TO);
 
@@ -306,7 +306,7 @@
 	new_dn_mark->dn = NULL;
 
 	/* this is needed to prevent the fcntl/close race described below */
-	mutex_lock(&dnotify_group->mark_mutex);
+	fsnotify_group_lock(dnotify_group);
 
 	/* add the new_fsn_mark or find an old one. */
 	fsn_mark = fsnotify_find_mark(&inode->i_fsnotify_marks, dnotify_group);
@@ -316,7 +316,7 @@
 	} else {
 		error = fsnotify_add_inode_mark_locked(new_fsn_mark, inode, 0);
 		if (error) {
-			mutex_unlock(&dnotify_group->mark_mutex);
+			fsnotify_group_unlock(dnotify_group);
 			goto out_err;
 		}
 		spin_lock(&new_fsn_mark->lock);
@@ -365,7 +365,7 @@
 
 	if (destroy)
 		fsnotify_detach_mark(fsn_mark);
-	mutex_unlock(&dnotify_group->mark_mutex);
+	fsnotify_group_unlock(dnotify_group);
 	if (destroy)
 		fsnotify_free_mark(fsn_mark);
 	fsnotify_put_mark(fsn_mark);
@@ -383,7 +383,8 @@
 					  SLAB_PANIC|SLAB_ACCOUNT);
 	dnotify_mark_cache = KMEM_CACHE(dnotify_mark, SLAB_PANIC|SLAB_ACCOUNT);
 
-	dnotify_group = fsnotify_alloc_group(&dnotify_fsnotify_ops);
+	dnotify_group = fsnotify_alloc_group(&dnotify_fsnotify_ops,
+					     FSNOTIFY_GROUP_NOFS);
 	if (IS_ERR(dnotify_group))
 		panic("unable to allocate fsnotify group for dnotify\n");
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/fanotify/fanotify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/fanotify/fanotify.c
@@ -18,7 +18,7 @@
 
 #include "fanotify.h"
 
-static bool fanotify_path_equal(struct path *p1, struct path *p2)
+static bool fanotify_path_equal(const struct path *p1, const struct path *p2)
 {
 	return p1->mnt == p2->mnt && p1->dentry == p2->dentry;
 }
@@ -76,8 +76,10 @@
 				struct fanotify_info *info2)
 {
 	if (info1->dir_fh_totlen != info2->dir_fh_totlen ||
+	    info1->dir2_fh_totlen != info2->dir2_fh_totlen ||
 	    info1->file_fh_totlen != info2->file_fh_totlen ||
-	    info1->name_len != info2->name_len)
+	    info1->name_len != info2->name_len ||
+	    info1->name2_len != info2->name2_len)
 		return false;
 
 	if (info1->dir_fh_totlen &&
@@ -85,14 +87,24 @@
 			       fanotify_info_dir_fh(info2)))
 		return false;
 
+	if (info1->dir2_fh_totlen &&
+	    !fanotify_fh_equal(fanotify_info_dir2_fh(info1),
+			       fanotify_info_dir2_fh(info2)))
+		return false;
+
 	if (info1->file_fh_totlen &&
 	    !fanotify_fh_equal(fanotify_info_file_fh(info1),
 			       fanotify_info_file_fh(info2)))
 		return false;
 
-	return !info1->name_len ||
-		!memcmp(fanotify_info_name(info1), fanotify_info_name(info2),
-			info1->name_len);
+	if (info1->name_len &&
+	    memcmp(fanotify_info_name(info1), fanotify_info_name(info2),
+		   info1->name_len))
+		return false;
+
+	return !info1->name2_len ||
+		!memcmp(fanotify_info_name2(info1), fanotify_info_name2(info2),
+			info1->name2_len);
 }
 
 static bool fanotify_name_event_equal(struct fanotify_name_event *fne1,
@@ -111,6 +123,16 @@
 	return fanotify_info_equal(info1, info2);
 }
 
+static bool fanotify_error_event_equal(struct fanotify_error_event *fee1,
+				       struct fanotify_error_event *fee2)
+{
+	/* Error events against the same file system are always merged. */
+	if (!fanotify_fsid_equal(&fee1->fsid, &fee2->fsid))
+		return false;
+
+	return true;
+}
+
 static bool fanotify_should_merge(struct fanotify_event *old,
 				  struct fanotify_event *new)
 {
@@ -131,6 +153,13 @@
 	if ((old->mask & FS_ISDIR) != (new->mask & FS_ISDIR))
 		return false;
 
+	/*
+	 * FAN_RENAME event is reported with special info record types,
+	 * so we cannot merge it with other events.
+	 */
+	if ((old->mask & FAN_RENAME) != (new->mask & FAN_RENAME))
+		return false;
+
 	switch (old->type) {
 	case FANOTIFY_EVENT_TYPE_PATH:
 		return fanotify_path_equal(fanotify_event_path(old),
@@ -141,6 +170,9 @@
 	case FANOTIFY_EVENT_TYPE_FID_NAME:
 		return fanotify_name_event_equal(FANOTIFY_NE(old),
 						 FANOTIFY_NE(new));
+	case FANOTIFY_EVENT_TYPE_FS_ERROR:
+		return fanotify_error_event_equal(FANOTIFY_EE(old),
+						  FANOTIFY_EE(new));
 	default:
 		WARN_ON_ONCE(1);
 	}
@@ -176,6 +208,10 @@
 			break;
 		if (fanotify_should_merge(old, new)) {
 			old->mask |= new->mask;
+
+			if (fanotify_is_error_event(old->mask))
+				FANOTIFY_EE(old)->err_count++;
+
 			return 1;
 		}
 	}
@@ -255,15 +291,17 @@
  */
 static u32 fanotify_group_event_mask(struct fsnotify_group *group,
 				     struct fsnotify_iter_info *iter_info,
-				     u32 event_mask, const void *data,
-				     int data_type, struct inode *dir)
+				     u32 *match_mask, u32 event_mask,
+				     const void *data, int data_type,
+				     struct inode *dir)
 {
-	__u32 marks_mask = 0, marks_ignored_mask = 0;
+	__u32 marks_mask = 0, marks_ignore_mask = 0;
 	__u32 test_mask, user_mask = FANOTIFY_OUTGOING_EVENTS |
 				     FANOTIFY_EVENT_FLAGS;
 	const struct path *path = fsnotify_data_path(data, data_type);
 	unsigned int fid_mode = FAN_GROUP_FLAG(group, FANOTIFY_FID_BITS);
 	struct fsnotify_mark *mark;
+	bool ondir = event_mask & FAN_ONDIR;
 	int type;
 
 	pr_debug("%s: report_mask=%x mask=%x data=%p data_type=%d\n",
@@ -278,37 +316,30 @@
 			return 0;
 	} else if (!(fid_mode & FAN_REPORT_FID)) {
 		/* Do we have a directory inode to report? */
-		if (!dir && !(event_mask & FS_ISDIR))
+		if (!dir && !ondir)
 			return 0;
 	}
 
-	fsnotify_foreach_obj_type(type) {
-		if (!fsnotify_iter_should_report_type(iter_info, type))
-			continue;
-		mark = iter_info->marks[type];
-
-		/* Apply ignore mask regardless of ISDIR and ON_CHILD flags */
-		marks_ignored_mask |= mark->ignored_mask;
-
+	fsnotify_foreach_iter_mark_type(iter_info, mark, type) {
 		/*
-		 * If the event is on dir and this mark doesn't care about
-		 * events on dir, don't send it!
+		 * Apply ignore mask depending on event flags in ignore mask.
 		 */
-		if (event_mask & FS_ISDIR && !(mark->mask & FS_ISDIR))
-			continue;
+		marks_ignore_mask |=
+			fsnotify_effective_ignore_mask(mark, ondir, type);
 
 		/*
-		 * If the event is on a child and this mark is on a parent not
-		 * watching children, don't send it!
+		 * Send the event depending on event flags in mark mask.
 		 */
-		if (type == FSNOTIFY_OBJ_TYPE_PARENT &&
-		    !(mark->mask & FS_EVENT_ON_CHILD))
+		if (!fsnotify_mask_applicable(mark->mask, ondir, type))
 			continue;
 
 		marks_mask |= mark->mask;
+
+		/* Record the mark types of this group that matched the event */
+		*match_mask |= 1U << type;
 	}
 
-	test_mask = event_mask & marks_mask & ~marks_ignored_mask;
+	test_mask = event_mask & marks_mask & ~marks_ignore_mask;
 
 	/*
 	 * For dirent modification events (create/delete/move) that do not carry
@@ -343,13 +374,23 @@
 static int fanotify_encode_fh_len(struct inode *inode)
 {
 	int dwords = 0;
+	int fh_len;
 
 	if (!inode)
 		return 0;
 
 	exportfs_encode_inode_fh(inode, NULL, &dwords, NULL);
+	fh_len = dwords << 2;
 
-	return dwords << 2;
+	/*
+	 * struct fanotify_error_event might be preallocated and is
+	 * limited to MAX_HANDLE_SZ.  This should never happen, but
+	 * safeguard by forcing an invalid file handle.
+	 */
+	if (WARN_ON_ONCE(fh_len > MAX_HANDLE_SZ))
+		return 0;
+
+	return fh_len;
 }
 
 /*
@@ -370,15 +411,21 @@
 	fh->type = FILEID_ROOT;
 	fh->len = 0;
 	fh->flags = 0;
+
+	/*
+	 * Invalid FHs are used by FAN_FS_ERROR for errors not
+	 * linked to any inode. The f_handle won't be reported
+	 * back to userspace.
+	 */
 	if (!inode)
-		return 0;
+		goto out;
 
 	/*
 	 * !gpf means preallocated variable size fh, but fh_len could
 	 * be zero in that case if encoding fh len failed.
 	 */
 	err = -ENOENT;
-	if (fh_len < 4 || WARN_ON_ONCE(fh_len % 4))
+	if (fh_len < 4 || WARN_ON_ONCE(fh_len % 4) || fh_len > MAX_HANDLE_SZ)
 		goto out_err;
 
 	/* No external buffer in a variable size allocated fh */
@@ -403,8 +450,13 @@
 	fh->type = type;
 	fh->len = fh_len;
 
-	/* Mix fh into event merge key */
-	*hash ^= fanotify_hash_fh(fh);
+out:
+	/*
+	 * Mix fh into event merge key.  Hash might be NULL in case of
+	 * unhashed FID events (i.e. FAN_FS_ERROR).
+	 */
+	if (hash)
+		*hash ^= fanotify_hash_fh(fh);
 
 	return FANOTIFY_FH_HDR_LEN + fh_len;
 
@@ -420,17 +472,41 @@
 }
 
 /*
- * The inode to use as identifier when reporting fid depends on the event.
- * Report the modified directory inode on dirent modification events.
- * Report the "victim" inode otherwise.
+ * FAN_REPORT_FID is ambiguous in that it reports the fid of the child for
+ * some events and the fid of the parent for create/delete/move events.
+ *
+ * With the FAN_REPORT_TARGET_FID flag, the fid of the child is reported
+ * also in create/delete/move events in addition to the fid of the parent
+ * and the name of the child.
+ */
+static inline bool fanotify_report_child_fid(unsigned int fid_mode, u32 mask)
+{
+	if (mask & ALL_FSNOTIFY_DIRENT_EVENTS)
+		return (fid_mode & FAN_REPORT_TARGET_FID);
+
+	return (fid_mode & FAN_REPORT_FID) && !(mask & FAN_ONDIR);
+}
+
+/*
+ * The inode to use as identifier when reporting fid depends on the event
+ * and the group flags.
+ *
+ * With the group flag FAN_REPORT_TARGET_FID, always report the child fid.
+ *
+ * Without the group flag FAN_REPORT_TARGET_FID, report the modified directory
+ * fid on dirent events and the child fid otherwise.
+ *
  * For example:
- * FS_ATTRIB reports the child inode even if reported on a watched parent.
- * FS_CREATE reports the modified dir inode and not the created inode.
+ * FS_ATTRIB reports the child fid even if reported on a watched parent.
+ * FS_CREATE reports the modified dir fid without FAN_REPORT_TARGET_FID.
+ *       and reports the created child fid with FAN_REPORT_TARGET_FID.
  */
 static struct inode *fanotify_fid_inode(u32 event_mask, const void *data,
-					int data_type, struct inode *dir)
+					int data_type, struct inode *dir,
+					unsigned int fid_mode)
 {
-	if (event_mask & ALL_FSNOTIFY_DIRENT_EVENTS)
+	if ((event_mask & ALL_FSNOTIFY_DIRENT_EVENTS) &&
+	    !(fid_mode & FAN_REPORT_TARGET_FID))
 		return dir;
 
 	return fsnotify_data_inode(data, data_type);
@@ -452,7 +528,7 @@
 	if (event_mask & ALL_FSNOTIFY_DIRENT_EVENTS)
 		return dir;
 
-	if (S_ISDIR(inode->i_mode))
+	if (inode && S_ISDIR(inode->i_mode))
 		return inode;
 
 	return dir;
@@ -514,25 +590,34 @@
 	return &ffe->fae;
 }
 
-static struct fanotify_event *fanotify_alloc_name_event(struct inode *id,
+static struct fanotify_event *fanotify_alloc_name_event(struct inode *dir,
 							__kernel_fsid_t *fsid,
 							const struct qstr *name,
 							struct inode *child,
+							struct dentry *moved,
 							unsigned int *hash,
 							gfp_t gfp)
 {
 	struct fanotify_name_event *fne;
 	struct fanotify_info *info;
 	struct fanotify_fh *dfh, *ffh;
-	unsigned int dir_fh_len = fanotify_encode_fh_len(id);
+	struct inode *dir2 = moved ? d_inode(moved->d_parent) : NULL;
+	const struct qstr *name2 = moved ? &moved->d_name : NULL;
+	unsigned int dir_fh_len = fanotify_encode_fh_len(dir);
+	unsigned int dir2_fh_len = fanotify_encode_fh_len(dir2);
 	unsigned int child_fh_len = fanotify_encode_fh_len(child);
-	unsigned int size;
-
-	size = sizeof(*fne) + FANOTIFY_FH_HDR_LEN + dir_fh_len;
+	unsigned long name_len = name ? name->len : 0;
+	unsigned long name2_len = name2 ? name2->len : 0;
+	unsigned int len, size;
+
+	/* Reserve terminating null byte even for empty name */
+	size = sizeof(*fne) + name_len + name2_len + 2;
+	if (dir_fh_len)
+		size += FANOTIFY_FH_HDR_LEN + dir_fh_len;
+	if (dir2_fh_len)
+		size += FANOTIFY_FH_HDR_LEN + dir2_fh_len;
 	if (child_fh_len)
 		size += FANOTIFY_FH_HDR_LEN + child_fh_len;
-	if (name)
-		size += name->len + 1;
 	fne = kmalloc(size, gfp);
 	if (!fne)
 		return NULL;
@@ -542,40 +627,97 @@
 	*hash ^= fanotify_hash_fsid(fsid);
 	info = &fne->info;
 	fanotify_info_init(info);
-	dfh = fanotify_info_dir_fh(info);
-	info->dir_fh_totlen = fanotify_encode_fh(dfh, id, dir_fh_len, hash, 0);
+	if (dir_fh_len) {
+		dfh = fanotify_info_dir_fh(info);
+		len = fanotify_encode_fh(dfh, dir, dir_fh_len, hash, 0);
+		fanotify_info_set_dir_fh(info, len);
+	}
+	if (dir2_fh_len) {
+		dfh = fanotify_info_dir2_fh(info);
+		len = fanotify_encode_fh(dfh, dir2, dir2_fh_len, hash, 0);
+		fanotify_info_set_dir2_fh(info, len);
+	}
 	if (child_fh_len) {
 		ffh = fanotify_info_file_fh(info);
-		info->file_fh_totlen = fanotify_encode_fh(ffh, child,
-							child_fh_len, hash, 0);
+		len = fanotify_encode_fh(ffh, child, child_fh_len, hash, 0);
+		fanotify_info_set_file_fh(info, len);
 	}
-	if (name) {
-		long salt = name->len;
-
+	if (name_len) {
 		fanotify_info_copy_name(info, name);
-		*hash ^= full_name_hash((void *)salt, name->name, name->len);
+		*hash ^= full_name_hash((void *)name_len, name->name, name_len);
+	}
+	if (name2_len) {
+		fanotify_info_copy_name2(info, name2);
+		*hash ^= full_name_hash((void *)name2_len, name2->name,
+					name2_len);
 	}
 
-	pr_debug("%s: ino=%lu size=%u dir_fh_len=%u child_fh_len=%u name_len=%u name='%.*s'\n",
-		 __func__, id->i_ino, size, dir_fh_len, child_fh_len,
+	pr_debug("%s: size=%u dir_fh_len=%u child_fh_len=%u name_len=%u name='%.*s'\n",
+		 __func__, size, dir_fh_len, child_fh_len,
 		 info->name_len, info->name_len, fanotify_info_name(info));
 
+	if (dir2_fh_len) {
+		pr_debug("%s: dir2_fh_len=%u name2_len=%u name2='%.*s'\n",
+			 __func__, dir2_fh_len, info->name2_len,
+			 info->name2_len, fanotify_info_name2(info));
+	}
+
 	return &fne->fae;
 }
 
-static struct fanotify_event *fanotify_alloc_event(struct fsnotify_group *group,
-						   u32 mask, const void *data,
-						   int data_type, struct inode *dir,
-						   const struct qstr *file_name,
-						   __kernel_fsid_t *fsid)
+static struct fanotify_event *fanotify_alloc_error_event(
+						struct fsnotify_group *group,
+						__kernel_fsid_t *fsid,
+						const void *data, int data_type,
+						unsigned int *hash)
+{
+	struct fs_error_report *report =
+			fsnotify_data_error_report(data, data_type);
+	struct inode *inode;
+	struct fanotify_error_event *fee;
+	int fh_len;
+
+	if (WARN_ON_ONCE(!report))
+		return NULL;
+
+	fee = mempool_alloc(&group->fanotify_data.error_events_pool, GFP_NOFS);
+	if (!fee)
+		return NULL;
+
+	fee->fae.type = FANOTIFY_EVENT_TYPE_FS_ERROR;
+	fee->error = report->error;
+	fee->err_count = 1;
+	fee->fsid = *fsid;
+
+	inode = report->inode;
+	fh_len = fanotify_encode_fh_len(inode);
+
+	/* Bad fh_len. Fallback to using an invalid fh. Should never happen. */
+	if (!fh_len && inode)
+		inode = NULL;
+
+	fanotify_encode_fh(&fee->object_fh, inode, fh_len, NULL, 0);
+
+	*hash ^= fanotify_hash_fsid(fsid);
+
+	return &fee->fae;
+}
+
+static struct fanotify_event *fanotify_alloc_event(
+				struct fsnotify_group *group,
+				u32 mask, const void *data, int data_type,
+				struct inode *dir, const struct qstr *file_name,
+				__kernel_fsid_t *fsid, u32 match_mask)
 {
 	struct fanotify_event *event = NULL;
 	gfp_t gfp = GFP_KERNEL_ACCOUNT;
-	struct inode *id = fanotify_fid_inode(mask, data, data_type, dir);
+	unsigned int fid_mode = FAN_GROUP_FLAG(group, FANOTIFY_FID_BITS);
+	struct inode *id = fanotify_fid_inode(mask, data, data_type, dir,
+					      fid_mode);
 	struct inode *dirid = fanotify_dfid_inode(mask, data, data_type, dir);
 	const struct path *path = fsnotify_data_path(data, data_type);
-	unsigned int fid_mode = FAN_GROUP_FLAG(group, FANOTIFY_FID_BITS);
 	struct mem_cgroup *old_memcg;
+	struct dentry *moved = NULL;
 	struct inode *child = NULL;
 	bool name_event = false;
 	unsigned int hash = 0;
@@ -584,11 +726,10 @@
 
 	if ((fid_mode & FAN_REPORT_DIR_FID) && dirid) {
 		/*
-		 * With both flags FAN_REPORT_DIR_FID and FAN_REPORT_FID, we
-		 * report the child fid for events reported on a non-dir child
+		 * For certain events and group flags, report the child fid
 		 * in addition to reporting the parent fid and maybe child name.
 		 */
-		if ((fid_mode & FAN_REPORT_FID) && id != dirid && !ondir)
+		if (fanotify_report_child_fid(fid_mode, mask) && id != dirid)
 			child = id;
 
 		id = dirid;
@@ -612,6 +753,38 @@
 		} else if ((mask & ALL_FSNOTIFY_DIRENT_EVENTS) || !ondir) {
 			name_event = true;
 		}
+
+		/*
+		 * In the special case of FAN_RENAME event, use the match_mask
+		 * to determine if we need to report only the old parent+name,
+		 * only the new parent+name or both.
+		 * 'dirid' and 'file_name' are the old parent+name and
+		 * 'moved' has the new parent+name.
+		 */
+		if (mask & FAN_RENAME) {
+			bool report_old, report_new;
+
+			if (WARN_ON_ONCE(!match_mask))
+				return NULL;
+
+			/* Report both old and new parent+name if sb watching */
+			report_old = report_new =
+				match_mask & (1U << FSNOTIFY_ITER_TYPE_SB);
+			report_old |=
+				match_mask & (1U << FSNOTIFY_ITER_TYPE_INODE);
+			report_new |=
+				match_mask & (1U << FSNOTIFY_ITER_TYPE_INODE2);
+
+			if (!report_old) {
+				/* Do not report old parent+name */
+				dirid = NULL;
+				file_name = NULL;
+			}
+			if (report_new) {
+				/* Report new parent+name */
+				moved = fsnotify_data_dentry(data, data_type);
+			}
+		}
 	}
 
 	/*
@@ -630,9 +803,12 @@
 
 	if (fanotify_is_perm_event(mask)) {
 		event = fanotify_alloc_perm_event(path, gfp);
-	} else if (name_event && (file_name || child)) {
-		event = fanotify_alloc_name_event(id, fsid, file_name, child,
-						  &hash, gfp);
+	} else if (fanotify_is_error_event(mask)) {
+		event = fanotify_alloc_error_event(group, fsid, data,
+						   data_type, &hash);
+	} else if (name_event && (file_name || moved || child)) {
+		event = fanotify_alloc_name_event(dirid, fsid, file_name, child,
+						  moved, &hash, gfp);
 	} else if (fid_mode) {
 		event = fanotify_alloc_fid_event(id, fsid, &hash, gfp);
 	} else {
@@ -664,16 +840,14 @@
  */
 static __kernel_fsid_t fanotify_get_fsid(struct fsnotify_iter_info *iter_info)
 {
+	struct fsnotify_mark *mark;
 	int type;
 	__kernel_fsid_t fsid = {};
 
-	fsnotify_foreach_obj_type(type) {
+	fsnotify_foreach_iter_mark_type(iter_info, mark, type) {
 		struct fsnotify_mark_connector *conn;
 
-		if (!fsnotify_iter_should_report_type(iter_info, type))
-			continue;
-
-		conn = READ_ONCE(iter_info->marks[type]->connector);
+		conn = READ_ONCE(mark->connector);
 		/* Mark is just getting destroyed or created? */
 		if (!conn)
 			continue;
@@ -702,6 +876,9 @@
 
 	assert_spin_locked(&group->notification_lock);
 
+	if (!fanotify_is_hashed_event(event->mask))
+		return;
+
 	pr_debug("%s: group=%p event=%p bucket=%u\n", __func__,
 		 group, event, bucket);
 
@@ -718,6 +895,7 @@
 	struct fanotify_event *event;
 	struct fsnotify_event *fsn_event;
 	__kernel_fsid_t fsid = {};
+	u32 match_mask = 0;
 
 	BUILD_BUG_ON(FAN_ACCESS != FS_ACCESS);
 	BUILD_BUG_ON(FAN_MODIFY != FS_MODIFY);
@@ -738,15 +916,18 @@
 	BUILD_BUG_ON(FAN_ONDIR != FS_ISDIR);
 	BUILD_BUG_ON(FAN_OPEN_EXEC != FS_OPEN_EXEC);
 	BUILD_BUG_ON(FAN_OPEN_EXEC_PERM != FS_OPEN_EXEC_PERM);
+	BUILD_BUG_ON(FAN_FS_ERROR != FS_ERROR);
+	BUILD_BUG_ON(FAN_RENAME != FS_RENAME);
 
-	BUILD_BUG_ON(HWEIGHT32(ALL_FANOTIFY_EVENT_BITS) != 19);
+	BUILD_BUG_ON(HWEIGHT32(ALL_FANOTIFY_EVENT_BITS) != 21);
 
-	mask = fanotify_group_event_mask(group, iter_info, mask, data,
-					 data_type, dir);
+	mask = fanotify_group_event_mask(group, iter_info, &match_mask,
+					 mask, data, data_type, dir);
 	if (!mask)
 		return 0;
 
-	pr_debug("%s: group=%p mask=%x\n", __func__, group, mask);
+	pr_debug("%s: group=%p mask=%x report_mask=%x\n", __func__,
+		 group, mask, match_mask);
 
 	if (fanotify_is_perm_event(mask)) {
 		/*
@@ -765,7 +946,7 @@
 	}
 
 	event = fanotify_alloc_event(group, mask, data, data_type, dir,
-				     file_name, &fsid);
+				     file_name, &fsid, match_mask);
 	ret = -ENOMEM;
 	if (unlikely(!event)) {
 		/*
@@ -778,9 +959,8 @@
 	}
 
 	fsn_event = &event->fse;
-	ret = fsnotify_add_event(group, fsn_event, fanotify_merge,
-				 fanotify_is_hashed_event(mask) ?
-				 fanotify_insert_event : NULL);
+	ret = fsnotify_insert_event(group, fsn_event, fanotify_merge,
+				    fanotify_insert_event);
 	if (ret) {
 		/* Permission events shouldn't be merged */
 		BUG_ON(ret == 1 && mask & FANOTIFY_PERM_EVENTS);
@@ -805,6 +985,9 @@
 	if (group->fanotify_data.ucounts)
 		dec_ucount(group->fanotify_data.ucounts,
 			   UCOUNT_FANOTIFY_GROUPS);
+
+	if (mempool_initialized(&group->fanotify_data.error_events_pool))
+		mempool_exit(&group->fanotify_data.error_events_pool);
 }
 
 static void fanotify_free_path_event(struct fanotify_event *event)
@@ -833,7 +1016,16 @@
 	kfree(FANOTIFY_NE(event));
 }
 
-static void fanotify_free_event(struct fsnotify_event *fsn_event)
+static void fanotify_free_error_event(struct fsnotify_group *group,
+				      struct fanotify_event *event)
+{
+	struct fanotify_error_event *fee = FANOTIFY_EE(event);
+
+	mempool_free(fee, &group->fanotify_data.error_events_pool);
+}
+
+static void fanotify_free_event(struct fsnotify_group *group,
+				struct fsnotify_event *fsn_event)
 {
 	struct fanotify_event *event;
 
@@ -855,6 +1047,9 @@
 	case FANOTIFY_EVENT_TYPE_OVERFLOW:
 		kfree(event);
 		break;
+	case FANOTIFY_EVENT_TYPE_FS_ERROR:
+		fanotify_free_error_event(group, event);
+		break;
 	default:
 		WARN_ON_ONCE(1);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/fanotify/fanotify.h
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/fanotify/fanotify.h
@@ -40,15 +40,45 @@
 struct fanotify_info {
 	/* size of dir_fh/file_fh including fanotify_fh hdr size */
 	u8 dir_fh_totlen;
+	u8 dir2_fh_totlen;
 	u8 file_fh_totlen;
 	u8 name_len;
-	u8 pad;
+	u8 name2_len;
+	u8 pad[3];
 	unsigned char buf[];
 	/*
 	 * (struct fanotify_fh) dir_fh starts at buf[0]
-	 * (optional) file_fh starts at buf[dir_fh_totlen]
-	 * name starts at buf[dir_fh_totlen + file_fh_totlen]
+	 * (optional) dir2_fh starts at buf[dir_fh_totlen]
+	 * (optional) file_fh starts at buf[dir_fh_totlen + dir2_fh_totlen]
+	 * name starts at buf[dir_fh_totlen + dir2_fh_totlen + file_fh_totlen]
+	 * ...
 	 */
+#define FANOTIFY_DIR_FH_SIZE(info)	((info)->dir_fh_totlen)
+#define FANOTIFY_DIR2_FH_SIZE(info)	((info)->dir2_fh_totlen)
+#define FANOTIFY_FILE_FH_SIZE(info)	((info)->file_fh_totlen)
+#define FANOTIFY_NAME_SIZE(info)	((info)->name_len + 1)
+#define FANOTIFY_NAME2_SIZE(info)	((info)->name2_len + 1)
+
+#define FANOTIFY_DIR_FH_OFFSET(info)	0
+#define FANOTIFY_DIR2_FH_OFFSET(info) \
+	(FANOTIFY_DIR_FH_OFFSET(info) + FANOTIFY_DIR_FH_SIZE(info))
+#define FANOTIFY_FILE_FH_OFFSET(info) \
+	(FANOTIFY_DIR2_FH_OFFSET(info) + FANOTIFY_DIR2_FH_SIZE(info))
+#define FANOTIFY_NAME_OFFSET(info) \
+	(FANOTIFY_FILE_FH_OFFSET(info) + FANOTIFY_FILE_FH_SIZE(info))
+#define FANOTIFY_NAME2_OFFSET(info) \
+	(FANOTIFY_NAME_OFFSET(info) + FANOTIFY_NAME_SIZE(info))
+
+#define FANOTIFY_DIR_FH_BUF(info) \
+	((info)->buf + FANOTIFY_DIR_FH_OFFSET(info))
+#define FANOTIFY_DIR2_FH_BUF(info) \
+	((info)->buf + FANOTIFY_DIR2_FH_OFFSET(info))
+#define FANOTIFY_FILE_FH_BUF(info) \
+	((info)->buf + FANOTIFY_FILE_FH_OFFSET(info))
+#define FANOTIFY_NAME_BUF(info) \
+	((info)->buf + FANOTIFY_NAME_OFFSET(info))
+#define FANOTIFY_NAME2_BUF(info) \
+	((info)->buf + FANOTIFY_NAME2_OFFSET(info))
 } __aligned(4);
 
 static inline bool fanotify_fh_has_ext_buf(struct fanotify_fh *fh)
@@ -87,7 +117,21 @@
 {
 	BUILD_BUG_ON(offsetof(struct fanotify_info, buf) % 4);
 
-	return (struct fanotify_fh *)info->buf;
+	return (struct fanotify_fh *)FANOTIFY_DIR_FH_BUF(info);
+}
+
+static inline int fanotify_info_dir2_fh_len(struct fanotify_info *info)
+{
+	if (!info->dir2_fh_totlen ||
+	    WARN_ON_ONCE(info->dir2_fh_totlen < FANOTIFY_FH_HDR_LEN))
+		return 0;
+
+	return info->dir2_fh_totlen - FANOTIFY_FH_HDR_LEN;
+}
+
+static inline struct fanotify_fh *fanotify_info_dir2_fh(struct fanotify_info *info)
+{
+	return (struct fanotify_fh *)FANOTIFY_DIR2_FH_BUF(info);
 }
 
 static inline int fanotify_info_file_fh_len(struct fanotify_info *info)
@@ -101,32 +145,90 @@
 
 static inline struct fanotify_fh *fanotify_info_file_fh(struct fanotify_info *info)
 {
-	return (struct fanotify_fh *)(info->buf + info->dir_fh_totlen);
+	return (struct fanotify_fh *)FANOTIFY_FILE_FH_BUF(info);
 }
 
-static inline const char *fanotify_info_name(struct fanotify_info *info)
+static inline char *fanotify_info_name(struct fanotify_info *info)
 {
-	return info->buf + info->dir_fh_totlen + info->file_fh_totlen;
+	if (!info->name_len)
+		return NULL;
+
+	return FANOTIFY_NAME_BUF(info);
+}
+
+static inline char *fanotify_info_name2(struct fanotify_info *info)
+{
+	if (!info->name2_len)
+		return NULL;
+
+	return FANOTIFY_NAME2_BUF(info);
 }
 
 static inline void fanotify_info_init(struct fanotify_info *info)
 {
+	BUILD_BUG_ON(FANOTIFY_FH_HDR_LEN + MAX_HANDLE_SZ > U8_MAX);
+	BUILD_BUG_ON(NAME_MAX > U8_MAX);
+
 	info->dir_fh_totlen = 0;
+	info->dir2_fh_totlen = 0;
 	info->file_fh_totlen = 0;
 	info->name_len = 0;
+	info->name2_len = 0;
 }
 
-static inline unsigned int fanotify_info_len(struct fanotify_info *info)
+/* These set/copy helpers MUST be called by order */
+static inline void fanotify_info_set_dir_fh(struct fanotify_info *info,
+					    unsigned int totlen)
 {
-	return info->dir_fh_totlen + info->file_fh_totlen + info->name_len;
+	if (WARN_ON_ONCE(info->dir2_fh_totlen > 0) ||
+	    WARN_ON_ONCE(info->file_fh_totlen > 0) ||
+	    WARN_ON_ONCE(info->name_len > 0) ||
+	    WARN_ON_ONCE(info->name2_len > 0))
+		return;
+
+	info->dir_fh_totlen = totlen;
+}
+
+static inline void fanotify_info_set_dir2_fh(struct fanotify_info *info,
+					     unsigned int totlen)
+{
+	if (WARN_ON_ONCE(info->file_fh_totlen > 0) ||
+	    WARN_ON_ONCE(info->name_len > 0) ||
+	    WARN_ON_ONCE(info->name2_len > 0))
+		return;
+
+	info->dir2_fh_totlen = totlen;
+}
+
+static inline void fanotify_info_set_file_fh(struct fanotify_info *info,
+					     unsigned int totlen)
+{
+	if (WARN_ON_ONCE(info->name_len > 0) ||
+	    WARN_ON_ONCE(info->name2_len > 0))
+		return;
+
+	info->file_fh_totlen = totlen;
 }
 
 static inline void fanotify_info_copy_name(struct fanotify_info *info,
 					   const struct qstr *name)
 {
+	if (WARN_ON_ONCE(name->len > NAME_MAX) ||
+	    WARN_ON_ONCE(info->name2_len > 0))
+		return;
+
 	info->name_len = name->len;
-	strcpy(info->buf + info->dir_fh_totlen + info->file_fh_totlen,
-	       name->name);
+	strcpy(fanotify_info_name(info), name->name);
+}
+
+static inline void fanotify_info_copy_name2(struct fanotify_info *info,
+					    const struct qstr *name)
+{
+	if (WARN_ON_ONCE(name->len > NAME_MAX))
+		return;
+
+	info->name2_len = name->len;
+	strcpy(fanotify_info_name2(info), name->name);
 }
 
 /*
@@ -141,6 +243,7 @@
 	FANOTIFY_EVENT_TYPE_PATH,
 	FANOTIFY_EVENT_TYPE_PATH_PERM,
 	FANOTIFY_EVENT_TYPE_OVERFLOW, /* struct fanotify_event */
+	FANOTIFY_EVENT_TYPE_FS_ERROR, /* struct fanotify_error_event */
 	__FANOTIFY_EVENT_TYPE_NUM
 };
 
@@ -170,12 +273,18 @@
 	event->pid = NULL;
 }
 
+#define FANOTIFY_INLINE_FH(name, size)					\
+struct {								\
+	struct fanotify_fh (name);					\
+	/* Space for object_fh.buf[] - access with fanotify_fh_buf() */	\
+	unsigned char _inline_fh_buf[(size)];				\
+}
+
 struct fanotify_fid_event {
 	struct fanotify_event fae;
 	__kernel_fsid_t fsid;
-	struct fanotify_fh object_fh;
-	/* Reserve space in object_fh.buf[] - access with fanotify_fh_buf() */
-	unsigned char _inline_fh_buf[FANOTIFY_INLINE_FH_LEN];
+
+	FANOTIFY_INLINE_FH(object_fh, FANOTIFY_INLINE_FH_LEN);
 };
 
 static inline struct fanotify_fid_event *
@@ -196,12 +305,30 @@
 	return container_of(event, struct fanotify_name_event, fae);
 }
 
+struct fanotify_error_event {
+	struct fanotify_event fae;
+	s32 error; /* Error reported by the Filesystem. */
+	u32 err_count; /* Suppressed errors count */
+
+	__kernel_fsid_t fsid; /* FSID this error refers to. */
+
+	FANOTIFY_INLINE_FH(object_fh, MAX_HANDLE_SZ);
+};
+
+static inline struct fanotify_error_event *
+FANOTIFY_EE(struct fanotify_event *event)
+{
+	return container_of(event, struct fanotify_error_event, fae);
+}
+
 static inline __kernel_fsid_t *fanotify_event_fsid(struct fanotify_event *event)
 {
 	if (event->type == FANOTIFY_EVENT_TYPE_FID)
 		return &FANOTIFY_FE(event)->fsid;
 	else if (event->type == FANOTIFY_EVENT_TYPE_FID_NAME)
 		return &FANOTIFY_NE(event)->fsid;
+	else if (event->type == FANOTIFY_EVENT_TYPE_FS_ERROR)
+		return &FANOTIFY_EE(event)->fsid;
 	else
 		return NULL;
 }
@@ -213,6 +340,8 @@
 		return &FANOTIFY_FE(event)->object_fh;
 	else if (event->type == FANOTIFY_EVENT_TYPE_FID_NAME)
 		return fanotify_info_file_fh(&FANOTIFY_NE(event)->info);
+	else if (event->type == FANOTIFY_EVENT_TYPE_FS_ERROR)
+		return &FANOTIFY_EE(event)->object_fh;
 	else
 		return NULL;
 }
@@ -244,6 +373,37 @@
 	return info ? fanotify_info_dir_fh_len(info) : 0;
 }
 
+static inline int fanotify_event_dir2_fh_len(struct fanotify_event *event)
+{
+	struct fanotify_info *info = fanotify_event_info(event);
+
+	return info ? fanotify_info_dir2_fh_len(info) : 0;
+}
+
+static inline bool fanotify_event_has_object_fh(struct fanotify_event *event)
+{
+	/* For error events, even zeroed fh are reported. */
+	if (event->type == FANOTIFY_EVENT_TYPE_FS_ERROR)
+		return true;
+	return fanotify_event_object_fh_len(event) > 0;
+}
+
+static inline bool fanotify_event_has_dir_fh(struct fanotify_event *event)
+{
+	return fanotify_event_dir_fh_len(event) > 0;
+}
+
+static inline bool fanotify_event_has_dir2_fh(struct fanotify_event *event)
+{
+	return fanotify_event_dir2_fh_len(event) > 0;
+}
+
+static inline bool fanotify_event_has_any_dir_fh(struct fanotify_event *event)
+{
+	return fanotify_event_has_dir_fh(event) ||
+		fanotify_event_has_dir2_fh(event);
+}
+
 struct fanotify_path_event {
 	struct fanotify_event fae;
 	struct path path;
@@ -287,13 +447,12 @@
 	return container_of(fse, struct fanotify_event, fse);
 }
 
-static inline bool fanotify_event_has_path(struct fanotify_event *event)
+static inline bool fanotify_is_error_event(u32 mask)
 {
-	return event->type == FANOTIFY_EVENT_TYPE_PATH ||
-		event->type == FANOTIFY_EVENT_TYPE_PATH_PERM;
+	return mask & FAN_FS_ERROR;
 }
 
-static inline struct path *fanotify_event_path(struct fanotify_event *event)
+static inline const struct path *fanotify_event_path(struct fanotify_event *event)
 {
 	if (event->type == FANOTIFY_EVENT_TYPE_PATH)
 		return &FANOTIFY_PE(event)->path;
@@ -315,7 +474,8 @@
  */
 static inline bool fanotify_is_hashed_event(u32 mask)
 {
-	return !fanotify_is_perm_event(mask) && !(mask & FS_Q_OVERFLOW);
+	return !(fanotify_is_perm_event(mask) ||
+		 fsnotify_is_overflow_event(mask));
 }
 
 static inline unsigned int fanotify_event_hash_bucket(
@@ -324,3 +484,17 @@
 {
 	return event->hash & FANOTIFY_HTABLE_MASK;
 }
+
+static inline unsigned int fanotify_mark_user_flags(struct fsnotify_mark *mark)
+{
+	unsigned int mflags = 0;
+
+	if (mark->flags & FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY)
+		mflags |= FAN_MARK_IGNORED_SURV_MODIFY;
+	if (mark->flags & FSNOTIFY_MARK_FLAG_NO_IREF)
+		mflags |= FAN_MARK_EVICTABLE;
+	if (mark->flags & FSNOTIFY_MARK_FLAG_HAS_IGNORE_FLAGS)
+		mflags |= FAN_MARK_IGNORE;
+
+	return mflags;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/fanotify/fanotify_user.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/fanotify/fanotify_user.c
@@ -30,6 +30,7 @@
 #define FANOTIFY_DEFAULT_MAX_EVENTS	16384
 #define FANOTIFY_OLD_DEFAULT_MAX_MARKS	8192
 #define FANOTIFY_DEFAULT_MAX_GROUPS	128
+#define FANOTIFY_DEFAULT_FEE_POOL_SIZE	32
 
 /*
  * Legacy fanotify marks limits (8192) is per group and we introduced a tunable
@@ -114,6 +115,8 @@
 	(sizeof(struct fanotify_event_info_fid) + sizeof(struct file_handle))
 #define FANOTIFY_PIDFD_INFO_HDR_LEN \
 	sizeof(struct fanotify_event_info_pidfd)
+#define FANOTIFY_ERROR_INFO_LEN \
+	(sizeof(struct fanotify_event_info_error))
 
 static int fanotify_fid_info_len(int fh_len, int name_len)
 {
@@ -126,17 +129,42 @@
 		       FANOTIFY_EVENT_ALIGN);
 }
 
-static int fanotify_event_info_len(unsigned int info_mode,
-				   struct fanotify_event *event)
+/* FAN_RENAME may have one or two dir+name info records */
+static int fanotify_dir_name_info_len(struct fanotify_event *event)
 {
 	struct fanotify_info *info = fanotify_event_info(event);
 	int dir_fh_len = fanotify_event_dir_fh_len(event);
-	int fh_len = fanotify_event_object_fh_len(event);
+	int dir2_fh_len = fanotify_event_dir2_fh_len(event);
 	int info_len = 0;
+
+	if (dir_fh_len)
+		info_len += fanotify_fid_info_len(dir_fh_len,
+						  info->name_len);
+	if (dir2_fh_len)
+		info_len += fanotify_fid_info_len(dir2_fh_len,
+						  info->name2_len);
+
+	return info_len;
+}
+
+static size_t fanotify_event_len(unsigned int info_mode,
+				 struct fanotify_event *event)
+{
+	size_t event_len = FAN_EVENT_METADATA_LEN;
+	struct fanotify_info *info;
+	int fh_len;
 	int dot_len = 0;
 
-	if (dir_fh_len) {
-		info_len += fanotify_fid_info_len(dir_fh_len, info->name_len);
+	if (!info_mode)
+		return event_len;
+
+	if (fanotify_is_error_event(event->mask))
+		event_len += FANOTIFY_ERROR_INFO_LEN;
+
+	info = fanotify_event_info(event);
+
+	if (fanotify_event_has_any_dir_fh(event)) {
+		event_len += fanotify_dir_name_info_len(event);
 	} else if ((info_mode & FAN_REPORT_NAME) &&
 		   (event->mask & FAN_ONDIR)) {
 		/*
@@ -147,12 +175,14 @@
 	}
 
 	if (info_mode & FAN_REPORT_PIDFD)
-		info_len += FANOTIFY_PIDFD_INFO_HDR_LEN;
+		event_len += FANOTIFY_PIDFD_INFO_HDR_LEN;
 
-	if (fh_len)
-		info_len += fanotify_fid_info_len(fh_len, dot_len);
+	if (fanotify_event_has_object_fh(event)) {
+		fh_len = fanotify_event_object_fh_len(event);
+		event_len += fanotify_fid_info_len(fh_len, dot_len);
+	}
 
-	return info_len;
+	return event_len;
 }
 
 /*
@@ -181,7 +211,7 @@
 static struct fanotify_event *get_one_event(struct fsnotify_group *group,
 					    size_t count)
 {
-	size_t event_size = FAN_EVENT_METADATA_LEN;
+	size_t event_size;
 	struct fanotify_event *event = NULL;
 	struct fsnotify_event *fsn_event;
 	unsigned int info_mode = FAN_GROUP_FLAG(group, FANOTIFY_INFO_MODES);
@@ -194,8 +224,7 @@
 		goto out;
 
 	event = FANOTIFY_E(fsn_event);
-	if (info_mode)
-		event_size += fanotify_event_info_len(info_mode, event);
+	event_size = fanotify_event_len(info_mode, event);
 
 	if (event_size > count) {
 		event = ERR_PTR(-EINVAL);
@@ -216,7 +245,7 @@
 	return event;
 }
 
-static int create_fd(struct fsnotify_group *group, struct path *path,
+static int create_fd(struct fsnotify_group *group, const struct path *path,
 		     struct file **file)
 {
 	int client_fd;
@@ -231,7 +260,7 @@
 	 * originally opened O_WRONLY.
 	 */
 	new_file = dentry_open(path,
-			       group->fanotify_data.f_flags | FMODE_NONOTIFY,
+			       group->fanotify_data.f_flags | __FMODE_NONOTIFY,
 			       current_cred());
 	if (IS_ERR(new_file)) {
 		/*
@@ -316,6 +345,27 @@
 	return -ENOENT;
 }
 
+static size_t copy_error_info_to_user(struct fanotify_event *event,
+				      char __user *buf, int count)
+{
+	struct fanotify_event_info_error info = { };
+	struct fanotify_error_event *fee = FANOTIFY_EE(event);
+
+	info.hdr.info_type = FAN_EVENT_INFO_TYPE_ERROR;
+	info.hdr.len = FANOTIFY_ERROR_INFO_LEN;
+
+	if (WARN_ON(count < info.hdr.len))
+		return -EFAULT;
+
+	info.error = fee->error;
+	info.error_count = fee->err_count;
+
+	if (copy_to_user(buf, &info, sizeof(info)))
+		return -EFAULT;
+
+	return info.hdr.len;
+}
+
 static int copy_fid_info_to_user(__kernel_fsid_t *fsid, struct fanotify_fh *fh,
 				 int info_type, const char *name,
 				 size_t name_len,
@@ -331,9 +381,6 @@
 	pr_debug("%s: fh_len=%zu name_len=%zu, info_len=%zu, count=%zu\n",
 		 __func__, fh_len, name_len, info_len, count);
 
-	if (!fh_len)
-		return 0;
-
 	if (WARN_ON_ONCE(len < sizeof(info) || len > count))
 		return -EFAULT;
 
@@ -348,6 +395,8 @@
 			return -EFAULT;
 		break;
 	case FAN_EVENT_INFO_TYPE_DFID_NAME:
+	case FAN_EVENT_INFO_TYPE_OLD_DFID_NAME:
+	case FAN_EVENT_INFO_TYPE_NEW_DFID_NAME:
 		if (WARN_ON_ONCE(!name || !name_len))
 			return -EFAULT;
 		break;
@@ -368,6 +417,11 @@
 
 	handle.handle_type = fh->type;
 	handle.handle_bytes = fh_len;
+
+	/* Mangle handle_type for bad file_handle */
+	if (!fh_len)
+		handle.handle_type = FILEID_INVALID;
+
 	if (copy_to_user(buf, &handle, sizeof(handle)))
 		return -EFAULT;
 
@@ -442,11 +496,19 @@
 	unsigned int pidfd_mode = info_mode & FAN_REPORT_PIDFD;
 
 	/*
-	 * Event info records order is as follows: dir fid + name, child fid.
+	 * Event info records order is as follows:
+	 * 1. dir fid + name
+	 * 2. (optional) new dir fid + new name
+	 * 3. (optional) child fid
 	 */
-	if (fanotify_event_dir_fh_len(event)) {
+	if (fanotify_event_has_dir_fh(event)) {
 		info_type = info->name_len ? FAN_EVENT_INFO_TYPE_DFID_NAME :
 					     FAN_EVENT_INFO_TYPE_DFID;
+
+		/* FAN_RENAME uses special info types */
+		if (event->mask & FAN_RENAME)
+			info_type = FAN_EVENT_INFO_TYPE_OLD_DFID_NAME;
+
 		ret = copy_fid_info_to_user(fanotify_event_fsid(event),
 					    fanotify_info_dir_fh(info),
 					    info_type,
@@ -460,7 +522,23 @@
 		total_bytes += ret;
 	}
 
-	if (fanotify_event_object_fh_len(event)) {
+	/* New dir fid+name may be reported in addition to old dir fid+name */
+	if (fanotify_event_has_dir2_fh(event)) {
+		info_type = FAN_EVENT_INFO_TYPE_NEW_DFID_NAME;
+		ret = copy_fid_info_to_user(fanotify_event_fsid(event),
+					    fanotify_info_dir2_fh(info),
+					    info_type,
+					    fanotify_info_name2(info),
+					    info->name2_len, buf, count);
+		if (ret < 0)
+			return ret;
+
+		buf += ret;
+		count -= ret;
+		total_bytes += ret;
+	}
+
+	if (fanotify_event_has_object_fh(event)) {
 		const char *dot = NULL;
 		int dot_len = 0;
 
@@ -520,6 +598,15 @@
 		total_bytes += ret;
 	}
 
+	if (fanotify_is_error_event(event->mask)) {
+		ret = copy_error_info_to_user(event, buf, count);
+		if (ret < 0)
+			return ret;
+		buf += ret;
+		count -= ret;
+		total_bytes += ret;
+	}
+
 	return total_bytes;
 }
 
@@ -528,7 +615,7 @@
 				  char __user *buf, size_t count)
 {
 	struct fanotify_event_metadata metadata;
-	struct path *path = fanotify_event_path(event);
+	const struct path *path = fanotify_event_path(event);
 	struct fanotify_info *info = fanotify_event_info(event);
 	unsigned int info_mode = FAN_GROUP_FLAG(group, FANOTIFY_INFO_MODES);
 	unsigned int pidfd_mode = info_mode & FAN_REPORT_PIDFD;
@@ -537,8 +624,7 @@
 
 	pr_debug("%s: group=%p event=%p\n", __func__, group, event);
 
-	metadata.event_len = FAN_EVENT_METADATA_LEN +
-				fanotify_event_info_len(info_mode, event);
+	metadata.event_len = fanotify_event_len(info_mode, event);
 	metadata.metadata_len = FAN_EVENT_METADATA_LEN;
 	metadata.vers = FANOTIFY_METADATA_VERSION;
 	metadata.reserved = 0;
@@ -611,9 +697,6 @@
 	if (fanotify_is_perm_event(event->mask))
 		FANOTIFY_PERM(event)->fd = fd;
 
-	if (f)
-		fd_install(fd, f);
-
 	if (info_mode) {
 		ret = copy_info_records_to_user(event, info, info_mode, pidfd,
 						buf, count);
@@ -621,6 +704,9 @@
 			goto out_close_fd;
 	}
 
+	if (f)
+		fd_install(fd, f);
+
 	return metadata.event_len;
 
 out_close_fd:
@@ -913,27 +999,28 @@
 					    __u32 mask, unsigned int flags,
 					    __u32 umask, int *destroy)
 {
-	__u32 oldmask = 0;
+	__u32 oldmask, newmask;
 
 	/* umask bits cannot be removed by user */
 	mask &= ~umask;
 	spin_lock(&fsn_mark->lock);
-	if (!(flags & FAN_MARK_IGNORED_MASK)) {
-		oldmask = fsn_mark->mask;
+	oldmask = fsnotify_calc_mask(fsn_mark);
+	if (!(flags & FANOTIFY_MARK_IGNORE_BITS)) {
 		fsn_mark->mask &= ~mask;
 	} else {
-		fsn_mark->ignored_mask &= ~mask;
+		fsn_mark->ignore_mask &= ~mask;
 	}
+	newmask = fsnotify_calc_mask(fsn_mark);
 	/*
 	 * We need to keep the mark around even if remaining mask cannot
 	 * result in any events (e.g. mask == FAN_ONDIR) to support incremenal
 	 * changes to the mask.
 	 * Destroy mark when only umask bits remain.
 	 */
-	*destroy = !((fsn_mark->mask | fsn_mark->ignored_mask) & ~umask);
+	*destroy = !((fsn_mark->mask | fsn_mark->ignore_mask) & ~umask);
 	spin_unlock(&fsn_mark->lock);
 
-	return mask & oldmask;
+	return oldmask & ~newmask;
 }
 
 static int fanotify_remove_mark(struct fsnotify_group *group,
@@ -944,10 +1031,10 @@
 	__u32 removed;
 	int destroy_mark;
 
-	mutex_lock(&group->mark_mutex);
+	fsnotify_group_lock(group);
 	fsn_mark = fsnotify_find_mark(connp, group);
 	if (!fsn_mark) {
-		mutex_unlock(&group->mark_mutex);
+		fsnotify_group_unlock(group);
 		return -ENOENT;
 	}
 
@@ -957,7 +1044,7 @@
 		fsnotify_recalc_mask(fsn_mark->connector);
 	if (destroy_mark)
 		fsnotify_detach_mark(fsn_mark);
-	mutex_unlock(&group->mark_mutex);
+	fsnotify_group_unlock(group);
 	if (destroy_mark)
 		fsnotify_free_mark(fsn_mark);
 
@@ -990,29 +1077,72 @@
 				    flags, umask);
 }
 
-static __u32 fanotify_mark_add_to_mask(struct fsnotify_mark *fsn_mark,
-				       __u32 mask,
-				       unsigned int flags)
+static bool fanotify_mark_update_flags(struct fsnotify_mark *fsn_mark,
+				       unsigned int fan_flags)
+{
+	bool want_iref = !(fan_flags & FAN_MARK_EVICTABLE);
+	unsigned int ignore = fan_flags & FANOTIFY_MARK_IGNORE_BITS;
+	bool recalc = false;
+
+	/*
+	 * When using FAN_MARK_IGNORE for the first time, mark starts using
+	 * independent event flags in ignore mask.  After that, trying to
+	 * update the ignore mask with the old FAN_MARK_IGNORED_MASK API
+	 * will result in EEXIST error.
+	 */
+	if (ignore == FAN_MARK_IGNORE)
+		fsn_mark->flags |= FSNOTIFY_MARK_FLAG_HAS_IGNORE_FLAGS;
+
+	/*
+	 * Setting FAN_MARK_IGNORED_SURV_MODIFY for the first time may lead to
+	 * the removal of the FS_MODIFY bit in calculated mask if it was set
+	 * because of an ignore mask that is now going to survive FS_MODIFY.
+	 */
+	if (ignore && (fan_flags & FAN_MARK_IGNORED_SURV_MODIFY) &&
+	    !(fsn_mark->flags & FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY)) {
+		fsn_mark->flags |= FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY;
+		if (!(fsn_mark->mask & FS_MODIFY))
+			recalc = true;
+	}
+
+	if (fsn_mark->connector->type != FSNOTIFY_OBJ_TYPE_INODE ||
+	    want_iref == !(fsn_mark->flags & FSNOTIFY_MARK_FLAG_NO_IREF))
+		return recalc;
+
+	/*
+	 * NO_IREF may be removed from a mark, but not added.
+	 * When removed, fsnotify_recalc_mask() will take the inode ref.
+	 */
+	WARN_ON_ONCE(!want_iref);
+	fsn_mark->flags &= ~FSNOTIFY_MARK_FLAG_NO_IREF;
+
+	return true;
+}
+
+static bool fanotify_mark_add_to_mask(struct fsnotify_mark *fsn_mark,
+				      __u32 mask, unsigned int fan_flags)
 {
-	__u32 oldmask = -1;
+	bool recalc;
 
 	spin_lock(&fsn_mark->lock);
-	if (!(flags & FAN_MARK_IGNORED_MASK)) {
-		oldmask = fsn_mark->mask;
+	if (!(fan_flags & FANOTIFY_MARK_IGNORE_BITS))
 		fsn_mark->mask |= mask;
-	} else {
-		fsn_mark->ignored_mask |= mask;
-		if (flags & FAN_MARK_IGNORED_SURV_MODIFY)
-			fsn_mark->flags |= FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY;
-	}
+	else
+		fsn_mark->ignore_mask |= mask;
+
+	recalc = fsnotify_calc_mask(fsn_mark) &
+		~fsnotify_conn_mask(fsn_mark->connector);
+
+	recalc |= fanotify_mark_update_flags(fsn_mark, fan_flags);
 	spin_unlock(&fsn_mark->lock);
 
-	return mask & ~oldmask;
+	return recalc;
 }
 
 static struct fsnotify_mark *fanotify_add_new_mark(struct fsnotify_group *group,
 						   fsnotify_connp_t *connp,
-						   unsigned int type,
+						   unsigned int obj_type,
+						   unsigned int fan_flags,
 						   __kernel_fsid_t *fsid)
 {
 	struct ucounts *ucounts = group->fanotify_data.ucounts;
@@ -1035,7 +1165,10 @@
 	}
 
 	fsnotify_init_mark(mark, group);
-	ret = fsnotify_add_mark_locked(mark, connp, type, 0, fsid);
+	if (fan_flags & FAN_MARK_EVICTABLE)
+		mark->flags |= FSNOTIFY_MARK_FLAG_NO_IREF;
+
+	ret = fsnotify_add_mark_locked(mark, connp, obj_type, 0, fsid);
 	if (ret) {
 		fsnotify_put_mark(mark);
 		goto out_dec_ucounts;
@@ -1049,31 +1182,94 @@
 	return ERR_PTR(ret);
 }
 
+static int fanotify_group_init_error_pool(struct fsnotify_group *group)
+{
+	if (mempool_initialized(&group->fanotify_data.error_events_pool))
+		return 0;
+
+	return mempool_init_kmalloc_pool(&group->fanotify_data.error_events_pool,
+					 FANOTIFY_DEFAULT_FEE_POOL_SIZE,
+					 sizeof(struct fanotify_error_event));
+}
+
+static int fanotify_may_update_existing_mark(struct fsnotify_mark *fsn_mark,
+					      unsigned int fan_flags)
+{
+	/*
+	 * Non evictable mark cannot be downgraded to evictable mark.
+	 */
+	if (fan_flags & FAN_MARK_EVICTABLE &&
+	    !(fsn_mark->flags & FSNOTIFY_MARK_FLAG_NO_IREF))
+		return -EEXIST;
+
+	/*
+	 * New ignore mask semantics cannot be downgraded to old semantics.
+	 */
+	if (fan_flags & FAN_MARK_IGNORED_MASK &&
+	    fsn_mark->flags & FSNOTIFY_MARK_FLAG_HAS_IGNORE_FLAGS)
+		return -EEXIST;
+
+	/*
+	 * An ignore mask that survives modify could never be downgraded to not
+	 * survive modify.  With new FAN_MARK_IGNORE semantics we make that rule
+	 * explicit and return an error when trying to update the ignore mask
+	 * without the original FAN_MARK_IGNORED_SURV_MODIFY value.
+	 */
+	if (fan_flags & FAN_MARK_IGNORE &&
+	    !(fan_flags & FAN_MARK_IGNORED_SURV_MODIFY) &&
+	    fsn_mark->flags & FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY)
+		return -EEXIST;
+
+	return 0;
+}
 
 static int fanotify_add_mark(struct fsnotify_group *group,
-			     fsnotify_connp_t *connp, unsigned int type,
-			     __u32 mask, unsigned int flags,
+			     fsnotify_connp_t *connp, unsigned int obj_type,
+			     __u32 mask, unsigned int fan_flags,
 			     __kernel_fsid_t *fsid)
 {
 	struct fsnotify_mark *fsn_mark;
-	__u32 added;
+	bool recalc;
+	int ret = 0;
 
-	mutex_lock(&group->mark_mutex);
+	fsnotify_group_lock(group);
 	fsn_mark = fsnotify_find_mark(connp, group);
 	if (!fsn_mark) {
-		fsn_mark = fanotify_add_new_mark(group, connp, type, fsid);
+		fsn_mark = fanotify_add_new_mark(group, connp, obj_type,
+						 fan_flags, fsid);
 		if (IS_ERR(fsn_mark)) {
-			mutex_unlock(&group->mark_mutex);
+			fsnotify_group_unlock(group);
 			return PTR_ERR(fsn_mark);
 		}
 	}
-	added = fanotify_mark_add_to_mask(fsn_mark, mask, flags);
-	if (added & ~fsnotify_conn_mask(fsn_mark->connector))
+
+	/*
+	 * Check if requested mark flags conflict with an existing mark flags.
+	 */
+	ret = fanotify_may_update_existing_mark(fsn_mark, fan_flags);
+	if (ret)
+		goto out;
+
+	/*
+	 * Error events are pre-allocated per group, only if strictly
+	 * needed (i.e. FAN_FS_ERROR was requested).
+	 */
+	if (!(fan_flags & FANOTIFY_MARK_IGNORE_BITS) &&
+	    (mask & FAN_FS_ERROR)) {
+		ret = fanotify_group_init_error_pool(group);
+		if (ret)
+			goto out;
+	}
+
+	recalc = fanotify_mark_add_to_mask(fsn_mark, mask, fan_flags);
+	if (recalc)
 		fsnotify_recalc_mask(fsn_mark->connector);
-	mutex_unlock(&group->mark_mutex);
+
+out:
+	fsnotify_group_unlock(group);
 
 	fsnotify_put_mark(fsn_mark);
-	return 0;
+	return ret;
 }
 
 static int fanotify_add_vfsmount_mark(struct fsnotify_group *group,
@@ -1100,10 +1296,10 @@
 
 	/*
 	 * If some other task has this inode open for write we should not add
-	 * an ignored mark, unless that ignored mark is supposed to survive
+	 * an ignore mask, unless that ignore mask is supposed to survive
 	 * modification changes anyway.
 	 */
-	if ((flags & FAN_MARK_IGNORED_MASK) &&
+	if ((flags & FANOTIFY_MARK_IGNORE_BITS) &&
 	    !(flags & FAN_MARK_IGNORED_SURV_MODIFY) &&
 	    inode_is_open_for_write(inode))
 		return 0;
@@ -1207,14 +1403,24 @@
 	if ((fid_mode & FAN_REPORT_NAME) && !(fid_mode & FAN_REPORT_DIR_FID))
 		return -EINVAL;
 
-	f_flags = O_RDWR | FMODE_NONOTIFY;
+	/*
+	 * FAN_REPORT_TARGET_FID requires FAN_REPORT_NAME and FAN_REPORT_FID
+	 * and is used as an indication to report both dir and child fid on all
+	 * dirent events.
+	 */
+	if ((fid_mode & FAN_REPORT_TARGET_FID) &&
+	    (!(fid_mode & FAN_REPORT_NAME) || !(fid_mode & FAN_REPORT_FID)))
+		return -EINVAL;
+
+	f_flags = O_RDWR | __FMODE_NONOTIFY;
 	if (flags & FAN_CLOEXEC)
 		f_flags |= O_CLOEXEC;
 	if (flags & FAN_NONBLOCK)
 		f_flags |= O_NONBLOCK;
 
 	/* fsnotify_alloc_group takes a ref.  Dropped in fanotify_release */
-	group = fsnotify_alloc_user_group(&fanotify_fsnotify_ops);
+	group = fsnotify_alloc_group(&fanotify_fsnotify_ops,
+				     FSNOTIFY_GROUP_USER | FSNOTIFY_GROUP_NOFS);
 	if (IS_ERR(group)) {
 		return PTR_ERR(group);
 	}
@@ -1295,16 +1501,15 @@
 	return fd;
 }
 
-/* Check if filesystem can encode a unique fid */
-static int fanotify_test_fid(struct path *path, __kernel_fsid_t *fsid)
+static int fanotify_test_fsid(struct dentry *dentry, __kernel_fsid_t *fsid)
 {
 	__kernel_fsid_t root_fsid;
 	int err;
 
 	/*
-	 * Make sure path is not in filesystem with zero fsid (e.g. tmpfs).
+	 * Make sure dentry is not of a filesystem with zero fsid (e.g. fuse).
 	 */
-	err = vfs_get_fsid(path->dentry, fsid);
+	err = vfs_get_fsid(dentry, fsid);
 	if (err)
 		return err;
 
@@ -1312,10 +1517,10 @@
 		return -ENODEV;
 
 	/*
-	 * Make sure path is not inside a filesystem subvolume (e.g. btrfs)
+	 * Make sure dentry is not of a filesystem subvolume (e.g. btrfs)
 	 * which uses a different fsid than sb root.
 	 */
-	err = vfs_get_fsid(path->dentry->d_sb->s_root, &root_fsid);
+	err = vfs_get_fsid(dentry->d_sb->s_root, &root_fsid);
 	if (err)
 		return err;
 
@@ -1323,6 +1528,12 @@
 	    root_fsid.val[1] != fsid->val[1])
 		return -EXDEV;
 
+	return 0;
+}
+
+/* Check if filesystem can encode a unique fid */
+static int fanotify_test_fid(struct dentry *dentry)
+{
 	/*
 	 * We need to make sure that the file system supports at least
 	 * encoding a file handle so user can use name_to_handle_at() to
@@ -1330,15 +1541,23 @@
 	 * objects. However, name_to_handle_at() requires that the
 	 * filesystem also supports decoding file handles.
 	 */
-	if (!path->dentry->d_sb->s_export_op ||
-	    !path->dentry->d_sb->s_export_op->fh_to_dentry)
+	if (!dentry->d_sb->s_export_op ||
+	    !dentry->d_sb->s_export_op->fh_to_dentry)
 		return -EOPNOTSUPP;
 
 	return 0;
 }
 
-static int fanotify_events_supported(struct path *path, __u64 mask)
+static int fanotify_events_supported(struct fsnotify_group *group,
+				     const struct path *path, __u64 mask,
+				     unsigned int flags)
 {
+	unsigned int mark_type = flags & FANOTIFY_MARK_TYPE_BITS;
+	/* Strict validation of events in non-dir inode mask with v5.17+ APIs */
+	bool strict_dir_events = FAN_GROUP_FLAG(group, FAN_REPORT_TARGET_FID) ||
+				 (mask & FAN_RENAME) ||
+				 (flags & FAN_MARK_IGNORE);
+
 	/*
 	 * Some filesystems such as 'proc' acquire unusual locks when opening
 	 * files. For them fanotify permission events have high chances of
@@ -1350,6 +1569,30 @@
 	if (mask & FANOTIFY_PERM_EVENTS &&
 	    path->mnt->mnt_sb->s_type->fs_flags & FS_DISALLOW_NOTIFY_PERM)
 		return -EINVAL;
+
+	/*
+	 * mount and sb marks are not allowed on kernel internal pseudo fs,
+	 * like pipe_mnt, because that would subscribe to events on all the
+	 * anonynous pipes in the system.
+	 *
+	 * SB_NOUSER covers all of the internal pseudo fs whose objects are not
+	 * exposed to user's mount namespace, but there are other SB_KERNMOUNT
+	 * fs, like nsfs, debugfs, for which the value of allowing sb and mount
+	 * mark is questionable. For now we leave them alone.
+	 */
+	if (mark_type != FAN_MARK_INODE &&
+	    path->mnt->mnt_sb->s_flags & SB_NOUSER)
+		return -EINVAL;
+
+	/*
+	 * We shouldn't have allowed setting dirent events and the directory
+	 * flags FAN_ONDIR and FAN_EVENT_ON_CHILD in mask of non-dir inode,
+	 * but because we always allowed it, error only when using new APIs.
+	 */
+	if (strict_dir_events && mark_type == FAN_MARK_INODE &&
+	    !d_is_dir(path->dentry) && (mask & FANOTIFY_DIRONLY_EVENT_BITS))
+		return -ENOTDIR;
+
 	return 0;
 }
 
@@ -1364,7 +1607,8 @@
 	__kernel_fsid_t __fsid, *fsid = NULL;
 	u32 valid_mask = FANOTIFY_EVENTS | FANOTIFY_EVENT_FLAGS;
 	unsigned int mark_type = flags & FANOTIFY_MARK_TYPE_BITS;
-	bool ignored = flags & FAN_MARK_IGNORED_MASK;
+	unsigned int mark_cmd = flags & FANOTIFY_MARK_CMD_BITS;
+	unsigned int ignore = flags & FANOTIFY_MARK_IGNORE_BITS;
 	unsigned int obj_type, fid_mode;
 	u32 umask = 0;
 	int ret;
@@ -1393,7 +1637,7 @@
 		return -EINVAL;
 	}
 
-	switch (flags & (FAN_MARK_ADD | FAN_MARK_REMOVE | FAN_MARK_FLUSH)) {
+	switch (mark_cmd) {
 	case FAN_MARK_ADD:
 	case FAN_MARK_REMOVE:
 		if (!mask)
@@ -1413,9 +1657,19 @@
 	if (mask & ~valid_mask)
 		return -EINVAL;
 
-	/* Event flags (ONDIR, ON_CHILD) are meaningless in ignored mask */
-	if (ignored)
+
+	/* We don't allow FAN_MARK_IGNORE & FAN_MARK_IGNORED_MASK together */
+	if (ignore == (FAN_MARK_IGNORE | FAN_MARK_IGNORED_MASK))
+		return -EINVAL;
+
+	/*
+	 * Event flags (FAN_ONDIR, FAN_EVENT_ON_CHILD) have no effect with
+	 * FAN_MARK_IGNORED_MASK.
+	 */
+	if (ignore == FAN_MARK_IGNORED_MASK) {
 		mask &= ~FANOTIFY_EVENT_FLAGS;
+		umask = FANOTIFY_EVENT_FLAGS;
+	}
 
 	f = fdget(fanotify_fd);
 	if (unlikely(!f.file))
@@ -1447,19 +1701,39 @@
 	    group->priority == FS_PRIO_0)
 		goto fput_and_out;
 
+	if (mask & FAN_FS_ERROR &&
+	    mark_type != FAN_MARK_FILESYSTEM)
+		goto fput_and_out;
+
+	/*
+	 * Evictable is only relevant for inode marks, because only inode object
+	 * can be evicted on memory pressure.
+	 */
+	if (flags & FAN_MARK_EVICTABLE &&
+	     mark_type != FAN_MARK_INODE)
+		goto fput_and_out;
+
 	/*
-	 * Events with data type inode do not carry enough information to report
-	 * event->fd, so we do not allow setting a mask for inode events unless
-	 * group supports reporting fid.
-	 * inode events are not supported on a mount mark, because they do not
-	 * carry enough information (i.e. path) to be filtered by mount point.
+	 * Events that do not carry enough information to report
+	 * event->fd require a group that supports reporting fid.  Those
+	 * events are not supported on a mount mark, because they do not
+	 * carry enough information (i.e. path) to be filtered by mount
+	 * point.
 	 */
 	fid_mode = FAN_GROUP_FLAG(group, FANOTIFY_FID_BITS);
-	if (mask & FANOTIFY_INODE_EVENTS &&
+	if (mask & ~(FANOTIFY_FD_EVENTS|FANOTIFY_EVENT_FLAGS) &&
 	    (!fid_mode || mark_type == FAN_MARK_MOUNT))
 		goto fput_and_out;
 
-	if (flags & FAN_MARK_FLUSH) {
+	/*
+	 * FAN_RENAME uses special info type records to report the old and
+	 * new parent+name.  Reporting only old and new parent id is less
+	 * useful and was not implemented.
+	 */
+	if (mask & FAN_RENAME && !(fid_mode & FAN_REPORT_NAME))
+		goto fput_and_out;
+
+	if (mark_cmd == FAN_MARK_FLUSH) {
 		ret = 0;
 		if (mark_type == FAN_MARK_MOUNT)
 			fsnotify_clear_vfsmount_marks_by_group(group);
@@ -1475,14 +1749,18 @@
 	if (ret)
 		goto fput_and_out;
 
-	if (flags & FAN_MARK_ADD) {
-		ret = fanotify_events_supported(&path, mask);
+	if (mark_cmd == FAN_MARK_ADD) {
+		ret = fanotify_events_supported(group, &path, mask, flags);
 		if (ret)
 			goto path_put_and_out;
 	}
 
 	if (fid_mode) {
-		ret = fanotify_test_fid(&path, &__fsid);
+		ret = fanotify_test_fsid(path.dentry, &__fsid);
+		if (ret)
+			goto path_put_and_out;
+
+		ret = fanotify_test_fid(path.dentry);
 		if (ret)
 			goto path_put_and_out;
 
@@ -1495,6 +1773,13 @@
 	else
 		mnt = path.mnt;
 
+	ret = mnt ? -EINVAL : -EISDIR;
+	/* FAN_MARK_IGNORE requires SURV_MODIFY for sb/mount/dir marks */
+	if (mark_cmd == FAN_MARK_ADD && ignore == FAN_MARK_IGNORE &&
+	    (mnt || S_ISDIR(inode->i_mode)) &&
+	    !(flags & FAN_MARK_IGNORED_SURV_MODIFY))
+		goto path_put_and_out;
+
 	/* Mask out FAN_EVENT_ON_CHILD flag for sb/mount/non-dir marks */
 	if (mnt || !S_ISDIR(inode->i_mode)) {
 		mask &= ~FAN_EVENT_ON_CHILD;
@@ -1504,12 +1789,12 @@
 		 * events with parent/name info for non-directory.
 		 */
 		if ((fid_mode & FAN_REPORT_DIR_FID) &&
-		    (flags & FAN_MARK_ADD) && !ignored)
+		    (flags & FAN_MARK_ADD) && !ignore)
 			mask |= FAN_EVENT_ON_CHILD;
 	}
 
 	/* create/update an inode mark */
-	switch (flags & (FAN_MARK_ADD | FAN_MARK_REMOVE)) {
+	switch (mark_cmd) {
 	case FAN_MARK_ADD:
 		if (mark_type == FAN_MARK_MOUNT)
 			ret = fanotify_add_vfsmount_mark(group, mnt, mask,
@@ -1586,8 +1871,8 @@
 				     FANOTIFY_DEFAULT_MAX_USER_MARKS);
 
 	BUILD_BUG_ON(FANOTIFY_INIT_FLAGS & FANOTIFY_INTERNAL_GROUP_FLAGS);
-	BUILD_BUG_ON(HWEIGHT32(FANOTIFY_INIT_FLAGS) != 11);
-	BUILD_BUG_ON(HWEIGHT32(FANOTIFY_MARK_FLAGS) != 9);
+	BUILD_BUG_ON(HWEIGHT32(FANOTIFY_INIT_FLAGS) != 12);
+	BUILD_BUG_ON(HWEIGHT32(FANOTIFY_MARK_FLAGS) != 11);
 
 	fanotify_mark_cache = KMEM_CACHE(fsnotify_mark,
 					 SLAB_PANIC|SLAB_ACCOUNT);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/fdinfo.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/fdinfo.c
@@ -14,6 +14,7 @@
 #include <linux/exportfs.h>
 
 #include "inotify/inotify.h"
+#include "fanotify/fanotify.h"
 #include "fdinfo.h"
 #include "fsnotify.h"
 
@@ -28,13 +29,13 @@
 	struct fsnotify_group *group = f->private_data;
 	struct fsnotify_mark *mark;
 
-	mutex_lock(&group->mark_mutex);
+	fsnotify_group_lock(group);
 	list_for_each_entry(mark, &group->marks_list, g_list) {
 		show(m, mark);
 		if (seq_has_overflowed(m))
 			break;
 	}
-	mutex_unlock(&group->mark_mutex);
+	fsnotify_group_unlock(group);
 }
 
 #if defined(CONFIG_EXPORTFS)
@@ -83,16 +84,9 @@
 	inode_mark = container_of(mark, struct inotify_inode_mark, fsn_mark);
 	inode = igrab(fsnotify_conn_inode(mark->connector));
 	if (inode) {
-		/*
-		 * IN_ALL_EVENTS represents all of the mask bits
-		 * that we expose to userspace.  There is at
-		 * least one bit (FS_EVENT_ON_CHILD) which is
-		 * used only internally to the kernel.
-		 */
-		u32 mask = mark->mask & IN_ALL_EVENTS;
-		seq_printf(m, "inotify wd:%x ino:%lx sdev:%x mask:%x ignored_mask:%x ",
+		seq_printf(m, "inotify wd:%x ino:%lx sdev:%x mask:%x ignored_mask:0 ",
 			   inode_mark->wd, inode->i_ino, inode->i_sb->s_dev,
-			   mask, mark->ignored_mask);
+			   inotify_mark_user_mask(mark));
 		show_mark_fhandle(m, inode);
 		seq_putc(m, '\n');
 		iput(inode);
@@ -110,19 +104,16 @@
 
 static void fanotify_fdinfo(struct seq_file *m, struct fsnotify_mark *mark)
 {
-	unsigned int mflags = 0;
+	unsigned int mflags = fanotify_mark_user_flags(mark);
 	struct inode *inode;
 
-	if (mark->flags & FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY)
-		mflags |= FAN_MARK_IGNORED_SURV_MODIFY;
-
 	if (mark->connector->type == FSNOTIFY_OBJ_TYPE_INODE) {
 		inode = igrab(fsnotify_conn_inode(mark->connector));
 		if (!inode)
 			return;
 		seq_printf(m, "fanotify ino:%lx sdev:%x mflags:%x mask:%x ignored_mask:%x ",
 			   inode->i_ino, inode->i_sb->s_dev,
-			   mflags, mark->mask, mark->ignored_mask);
+			   mflags, mark->mask, mark->ignore_mask);
 		show_mark_fhandle(m, inode);
 		seq_putc(m, '\n');
 		iput(inode);
@@ -130,12 +121,12 @@
 		struct mount *mnt = fsnotify_conn_mount(mark->connector);
 
 		seq_printf(m, "fanotify mnt_id:%x mflags:%x mask:%x ignored_mask:%x\n",
-			   mnt->mnt_id, mflags, mark->mask, mark->ignored_mask);
+			   mnt->mnt_id, mflags, mark->mask, mark->ignore_mask);
 	} else if (mark->connector->type == FSNOTIFY_OBJ_TYPE_SB) {
 		struct super_block *sb = fsnotify_conn_sb(mark->connector);
 
 		seq_printf(m, "fanotify sdev:%x mflags:%x mask:%x ignored_mask:%x\n",
-			   sb->s_dev, mflags, mark->mask, mark->ignored_mask);
+			   sb->s_dev, mflags, mark->mask, mark->ignore_mask);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/fsnotify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/fsnotify.c
@@ -70,8 +70,7 @@
 		spin_unlock(&inode->i_lock);
 		spin_unlock(&sb->s_inode_list_lock);
 
-		if (iput_inode)
-			iput(iput_inode);
+		iput(iput_inode);
 
 		/* for each watch, send FS_UNMOUNT and then remove it */
 		fsnotify_inode(inode, FS_UNMOUNT);
@@ -85,8 +84,7 @@
 	}
 	spin_unlock(&sb->s_inode_list_lock);
 
-	if (iput_inode)
-		iput(iput_inode);
+	iput(iput_inode);
 }
 
 void fsnotify_sb_delete(struct super_block *sb)
@@ -102,20 +100,16 @@
  * Given an inode, first check if we care what happens to our children.  Inotify
  * and dnotify both tell their parents about events.  If we care about any event
  * on a child we run all of our children and set a dentry flag saying that the
- * parent cares.  Thus when an event happens on a child it can quickly tell if
+ * parent cares.  Thus when an event happens on a child it can quickly tell
  * if there is a need to find a parent and send the event to the parent.
  */
-void __fsnotify_update_child_dentry_flags(struct inode *inode)
+void fsnotify_set_children_dentry_flags(struct inode *inode)
 {
 	struct dentry *alias;
-	int watched;
 
 	if (!S_ISDIR(inode->i_mode))
 		return;
 
-	/* determine if the children should tell inode about their events */
-	watched = fsnotify_inode_watches_children(inode);
-
 	spin_lock(&inode->i_lock);
 	/* run all of the dentries associated with this inode.  Since this is a
 	 * directory, there damn well better only be one item on this list */
@@ -131,10 +125,7 @@
 				continue;
 
 			spin_lock_nested(&child->d_lock, DENTRY_D_LOCK_NESTED);
-			if (watched)
-				child->d_flags |= DCACHE_FSNOTIFY_PARENT_WATCHED;
-			else
-				child->d_flags &= ~DCACHE_FSNOTIFY_PARENT_WATCHED;
+			child->d_flags |= DCACHE_FSNOTIFY_PARENT_WATCHED;
 			spin_unlock(&child->d_lock);
 		}
 		spin_unlock(&alias->d_lock);
@@ -142,6 +133,24 @@
 	spin_unlock(&inode->i_lock);
 }
 
+/*
+ * Lazily clear false positive PARENT_WATCHED flag for child whose parent had
+ * stopped watching children.
+ */
+static void fsnotify_clear_child_dentry_flag(struct inode *pinode,
+					     struct dentry *dentry)
+{
+	spin_lock(&dentry->d_lock);
+	/*
+	 * d_lock is a sufficient barrier to prevent observing a non-watched
+	 * parent state from before the fsnotify_set_children_dentry_flags()
+	 * or fsnotify_update_flags() call that had set PARENT_WATCHED.
+	 */
+	if (!fsnotify_inode_watches_children(pinode))
+		dentry->d_flags &= ~DCACHE_FSNOTIFY_PARENT_WATCHED;
+	spin_unlock(&dentry->d_lock);
+}
+
 /* Are inode/sb/mount interested in parent and name info with this event? */
 static bool fsnotify_event_needs_parent(struct inode *inode, struct mount *mnt,
 					__u32 mask)
@@ -210,7 +219,7 @@
 	p_inode = parent->d_inode;
 	p_mask = fsnotify_inode_watches_children(p_inode);
 	if (unlikely(parent_watched && !p_mask))
-		__fsnotify_update_child_dentry_flags(p_inode);
+		fsnotify_clear_child_dentry_flag(p_inode, dentry);
 
 	/*
 	 * Include parent/name in notification either if some notification
@@ -252,7 +261,10 @@
 	if (WARN_ON_ONCE(!ops->handle_inode_event))
 		return 0;
 
-	if ((inode_mark->mask & FS_EXCL_UNLINK) &&
+	if (WARN_ON_ONCE(!inode && !dir))
+		return 0;
+
+	if ((inode_mark->flags & FSNOTIFY_MARK_FLAG_EXCL_UNLINK) &&
 	    path && d_unlinked(path->dentry))
 		return 0;
 
@@ -276,33 +288,41 @@
 	    WARN_ON_ONCE(fsnotify_iter_vfsmount_mark(iter_info)))
 		return 0;
 
-	if (parent_mark) {
-		/*
-		 * parent_mark indicates that the parent inode is watching
-		 * children and interested in this event, which is an event
-		 * possible on child. But is *this mark* watching children and
-		 * interested in this event?
-		 */
-		if (parent_mark->mask & FS_EVENT_ON_CHILD) {
-			ret = fsnotify_handle_inode_event(group, parent_mark, mask,
-							  data, data_type, dir, name, 0);
-			if (ret)
-				return ret;
-		}
-		if (!inode_mark)
+	/*
+	 * For FS_RENAME, 'dir' is old dir and 'data' is new dentry.
+	 * The only ->handle_inode_event() backend that supports FS_RENAME is
+	 * dnotify, where it means file was renamed within same parent.
+	 */
+	if (mask & FS_RENAME) {
+		struct dentry *moved = fsnotify_data_dentry(data, data_type);
+
+		if (dir != moved->d_parent->d_inode)
 			return 0;
 	}
 
-	if (mask & FS_EVENT_ON_CHILD) {
-		/*
-		 * Some events can be sent on both parent dir and child marks
-		 * (e.g. FS_ATTRIB).  If both parent dir and child are
-		 * watching, report the event once to parent dir with name (if
-		 * interested) and once to child without name (if interested).
-		 * The child watcher is expecting an event without a file name
-		 * and without the FS_EVENT_ON_CHILD flag.
-		 */
-		mask &= ~FS_EVENT_ON_CHILD;
+	if (parent_mark) {
+		ret = fsnotify_handle_inode_event(group, parent_mark, mask,
+						  data, data_type, dir, name, 0);
+		if (ret)
+			return ret;
+	}
+
+	if (!inode_mark)
+		return 0;
+
+	/*
+	 * Some events can be sent on both parent dir and child marks (e.g.
+	 * FS_ATTRIB).  If both parent dir and child are watching, report the
+	 * event once to parent dir with name (if interested) and once to child
+	 * without name (if interested).
+	 *
+	 * In any case regardless whether the parent is watching or not, the
+	 * child watcher is expecting an event without the FS_EVENT_ON_CHILD
+	 * flag. The file name is expected if and only if this is a directory
+	 * event.
+	 */
+	mask &= ~FS_EVENT_ON_CHILD;
+	if (!(mask & ALL_FSNOTIFY_DIRENT_EVENTS)) {
 		dir = NULL;
 		name = NULL;
 	}
@@ -318,42 +338,36 @@
 	struct fsnotify_group *group = NULL;
 	__u32 test_mask = (mask & ALL_FSNOTIFY_EVENTS);
 	__u32 marks_mask = 0;
-	__u32 marks_ignored_mask = 0;
+	__u32 marks_ignore_mask = 0;
+	bool is_dir = mask & FS_ISDIR;
 	struct fsnotify_mark *mark;
 	int type;
 
-	if (WARN_ON(!iter_info->report_mask))
+	if (!iter_info->report_mask)
 		return 0;
 
 	/* clear ignored on inode modification */
 	if (mask & FS_MODIFY) {
-		fsnotify_foreach_obj_type(type) {
-			if (!fsnotify_iter_should_report_type(iter_info, type))
-				continue;
-			mark = iter_info->marks[type];
-			if (mark &&
-			    !(mark->flags & FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY))
-				mark->ignored_mask = 0;
+		fsnotify_foreach_iter_mark_type(iter_info, mark, type) {
+			if (!(mark->flags &
+			      FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY))
+				mark->ignore_mask = 0;
 		}
 	}
 
-	fsnotify_foreach_obj_type(type) {
-		if (!fsnotify_iter_should_report_type(iter_info, type))
-			continue;
-		mark = iter_info->marks[type];
-		/* does the object mark tell us to do something? */
-		if (mark) {
-			group = mark->group;
-			marks_mask |= mark->mask;
-			marks_ignored_mask |= mark->ignored_mask;
-		}
+	/* Are any of the group marks interested in this event? */
+	fsnotify_foreach_iter_mark_type(iter_info, mark, type) {
+		group = mark->group;
+		marks_mask |= mark->mask;
+		marks_ignore_mask |=
+			fsnotify_effective_ignore_mask(mark, is_dir, type);
 	}
 
-	pr_debug("%s: group=%p mask=%x marks_mask=%x marks_ignored_mask=%x data=%p data_type=%d dir=%p cookie=%d\n",
-		 __func__, group, mask, marks_mask, marks_ignored_mask,
+	pr_debug("%s: group=%p mask=%x marks_mask=%x marks_ignore_mask=%x data=%p data_type=%d dir=%p cookie=%d\n",
+		 __func__, group, mask, marks_mask, marks_ignore_mask,
 		 data, data_type, dir, cookie);
 
-	if (!(test_mask & marks_mask & ~marks_ignored_mask))
+	if (!(test_mask & marks_mask & ~marks_ignore_mask))
 		return 0;
 
 	if (group->ops->handle_event) {
@@ -390,11 +404,11 @@
 
 /*
  * iter_info is a multi head priority queue of marks.
- * Pick a subset of marks from queue heads, all with the
- * same group and set the report_mask for selected subset.
- * Returns the report_mask of the selected subset.
+ * Pick a subset of marks from queue heads, all with the same group
+ * and set the report_mask to a subset of the selected marks.
+ * Returns false if there are no more groups to iterate.
  */
-static unsigned int fsnotify_iter_select_report_types(
+static bool fsnotify_iter_select_report_types(
 		struct fsnotify_iter_info *iter_info)
 {
 	struct fsnotify_group *max_prio_group = NULL;
@@ -402,7 +416,7 @@
 	int type;
 
 	/* Choose max prio group among groups of all queue heads */
-	fsnotify_foreach_obj_type(type) {
+	fsnotify_foreach_iter_type(type) {
 		mark = iter_info->marks[type];
 		if (mark &&
 		    fsnotify_compare_groups(max_prio_group, mark->group) > 0)
@@ -410,30 +424,49 @@
 	}
 
 	if (!max_prio_group)
-		return 0;
+		return false;
 
 	/* Set the report mask for marks from same group as max prio group */
+	iter_info->current_group = max_prio_group;
 	iter_info->report_mask = 0;
-	fsnotify_foreach_obj_type(type) {
+	fsnotify_foreach_iter_type(type) {
 		mark = iter_info->marks[type];
-		if (mark &&
-		    fsnotify_compare_groups(max_prio_group, mark->group) == 0)
+		if (mark && mark->group == iter_info->current_group) {
+			/*
+			 * FSNOTIFY_ITER_TYPE_PARENT indicates that this inode
+			 * is watching children and interested in this event,
+			 * which is an event possible on child.
+			 * But is *this mark* watching children?
+			 */
+			if (type == FSNOTIFY_ITER_TYPE_PARENT &&
+			    !(mark->mask & FS_EVENT_ON_CHILD) &&
+			    !(fsnotify_ignore_mask(mark) & FS_EVENT_ON_CHILD))
+				continue;
+
 			fsnotify_iter_set_report_type(iter_info, type);
+		}
 	}
 
-	return iter_info->report_mask;
+	return true;
 }
 
 /*
- * Pop from iter_info multi head queue, the marks that were iterated in the
+ * Pop from iter_info multi head queue, the marks that belong to the group of
  * current iteration step.
  */
 static void fsnotify_iter_next(struct fsnotify_iter_info *iter_info)
 {
+	struct fsnotify_mark *mark;
 	int type;
 
-	fsnotify_foreach_obj_type(type) {
-		if (fsnotify_iter_should_report_type(iter_info, type))
+	/*
+	 * We cannot use fsnotify_foreach_iter_mark_type() here because we
+	 * may need to advance a mark of type X that belongs to current_group
+	 * but was not selected for reporting.
+	 */
+	fsnotify_foreach_iter_type(type) {
+		mark = iter_info->marks[type];
+		if (mark && mark->group == iter_info->current_group)
 			iter_info->marks[type] =
 				fsnotify_next_mark(iter_info->marks[type]);
 	}
@@ -455,18 +488,20 @@
  *		@file_name is relative to
  * @file_name:	optional file name associated with event
  * @inode:	optional inode associated with event -
- *		either @dir or @inode must be non-NULL.
- *		if both are non-NULL event may be reported to both.
+ *		If @dir and @inode are both non-NULL, event may be
+ *		reported to both.
  * @cookie:	inotify rename cookie
  */
 int fsnotify(__u32 mask, const void *data, int data_type, struct inode *dir,
 	     const struct qstr *file_name, struct inode *inode, u32 cookie)
 {
 	const struct path *path = fsnotify_data_path(data, data_type);
+	struct super_block *sb = fsnotify_data_sb(data, data_type);
 	struct fsnotify_iter_info iter_info = {};
-	struct super_block *sb;
 	struct mount *mnt = NULL;
-	struct inode *parent = NULL;
+	struct inode *inode2 = NULL;
+	struct dentry *moved;
+	int inode2_type;
 	int ret = 0;
 	__u32 test_mask, marks_mask;
 
@@ -476,14 +511,20 @@
 	if (!inode) {
 		/* Dirent event - report on TYPE_INODE to dir */
 		inode = dir;
+		/* For FS_RENAME, inode is old_dir and inode2 is new_dir */
+		if (mask & FS_RENAME) {
+			moved = fsnotify_data_dentry(data, data_type);
+			inode2 = moved->d_parent->d_inode;
+			inode2_type = FSNOTIFY_ITER_TYPE_INODE2;
+		}
 	} else if (mask & FS_EVENT_ON_CHILD) {
 		/*
 		 * Event on child - report on TYPE_PARENT to dir if it is
 		 * watching children and on TYPE_INODE to child.
 		 */
-		parent = dir;
+		inode2 = dir;
+		inode2_type = FSNOTIFY_ITER_TYPE_PARENT;
 	}
-	sb = inode->i_sb;
 
 	/*
 	 * Optimization: srcu_read_lock() has a memory barrier which can
@@ -495,7 +536,7 @@
 	if (!sb->s_fsnotify_marks &&
 	    (!mnt || !mnt->mnt_fsnotify_marks) &&
 	    (!inode || !inode->i_fsnotify_marks) &&
-	    (!parent || !parent->i_fsnotify_marks))
+	    (!inode2 || !inode2->i_fsnotify_marks))
 		return 0;
 
 	marks_mask = sb->s_fsnotify_mask;
@@ -503,33 +544,35 @@
 		marks_mask |= mnt->mnt_fsnotify_mask;
 	if (inode)
 		marks_mask |= inode->i_fsnotify_mask;
-	if (parent)
-		marks_mask |= parent->i_fsnotify_mask;
+	if (inode2)
+		marks_mask |= inode2->i_fsnotify_mask;
 
 
 	/*
-	 * if this is a modify event we may need to clear the ignored masks
-	 * otherwise return if none of the marks care about this type of event.
+	 * If this is a modify event we may need to clear some ignore masks.
+	 * In that case, the object with ignore masks will have the FS_MODIFY
+	 * event in its mask.
+	 * Otherwise, return if none of the marks care about this type of event.
 	 */
 	test_mask = (mask & ALL_FSNOTIFY_EVENTS);
-	if (!(mask & FS_MODIFY) && !(test_mask & marks_mask))
+	if (!(test_mask & marks_mask))
 		return 0;
 
 	iter_info.srcu_idx = srcu_read_lock(&fsnotify_mark_srcu);
 
-	iter_info.marks[FSNOTIFY_OBJ_TYPE_SB] =
+	iter_info.marks[FSNOTIFY_ITER_TYPE_SB] =
 		fsnotify_first_mark(&sb->s_fsnotify_marks);
 	if (mnt) {
-		iter_info.marks[FSNOTIFY_OBJ_TYPE_VFSMOUNT] =
+		iter_info.marks[FSNOTIFY_ITER_TYPE_VFSMOUNT] =
 			fsnotify_first_mark(&mnt->mnt_fsnotify_marks);
 	}
 	if (inode) {
-		iter_info.marks[FSNOTIFY_OBJ_TYPE_INODE] =
+		iter_info.marks[FSNOTIFY_ITER_TYPE_INODE] =
 			fsnotify_first_mark(&inode->i_fsnotify_marks);
 	}
-	if (parent) {
-		iter_info.marks[FSNOTIFY_OBJ_TYPE_PARENT] =
-			fsnotify_first_mark(&parent->i_fsnotify_marks);
+	if (inode2) {
+		iter_info.marks[inode2_type] =
+			fsnotify_first_mark(&inode2->i_fsnotify_marks);
 	}
 
 	/*
@@ -558,7 +601,7 @@
 {
 	int ret;
 
-	BUILD_BUG_ON(HWEIGHT32(ALL_FSNOTIFY_BITS) != 25);
+	BUILD_BUG_ON(HWEIGHT32(ALL_FSNOTIFY_BITS) != 23);
 
 	ret = init_srcu_struct(&fsnotify_mark_srcu);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/fsnotify.h
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/fsnotify.h
@@ -74,11 +74,7 @@
  * update the dentry->d_flags of all of inode's children to indicate if inode cares
  * about events that happen to its children.
  */
-extern void __fsnotify_update_child_dentry_flags(struct inode *inode);
-
-/* allocate and destroy and event holder to attach events to notification/access queues */
-extern struct fsnotify_event_holder *fsnotify_alloc_event_holder(void);
-extern void fsnotify_destroy_event_holder(struct fsnotify_event_holder *holder);
+extern void fsnotify_set_children_dentry_flags(struct inode *inode);
 
 extern struct kmem_cache *fsnotify_mark_connector_cachep;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/group.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/group.c
@@ -58,7 +58,7 @@
 	fsnotify_group_stop_queueing(group);
 
 	/* Clear all marks for this group and queue them for destruction */
-	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_ALL_TYPES_MASK);
+	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_ANY);
 
 	/*
 	 * Some marks can still be pinned when waiting for response from
@@ -88,7 +88,7 @@
 	 * that deliberately ignores overflow events.
 	 */
 	if (group->overflow_event)
-		group->ops->free_event(group->overflow_event);
+		group->ops->free_event(group, group->overflow_event);
 
 	fsnotify_put_group(group);
 }
@@ -100,6 +100,7 @@
 {
 	refcount_inc(&group->refcnt);
 }
+EXPORT_SYMBOL_GPL(fsnotify_get_group);
 
 /*
  * Drop a reference to a group.  Free it if it's through.
@@ -112,8 +113,10 @@
 EXPORT_SYMBOL_GPL(fsnotify_put_group);
 
 static struct fsnotify_group *__fsnotify_alloc_group(
-				const struct fsnotify_ops *ops, gfp_t gfp)
+				const struct fsnotify_ops *ops,
+				int flags, gfp_t gfp)
 {
+	static struct lock_class_key nofs_marks_lock;
 	struct fsnotify_group *group;
 
 	group = kzalloc(sizeof(struct fsnotify_group), gfp);
@@ -133,6 +136,17 @@
 	INIT_LIST_HEAD(&group->marks_list);
 
 	group->ops = ops;
+	group->flags = flags;
+	/*
+	 * For most backends, eviction of inode with a mark is not expected,
+	 * because marks hold a refcount on the inode against eviction.
+	 *
+	 * Use a different lockdep class for groups that support evictable
+	 * inode marks, because with evictable marks, mark_mutex is NOT
+	 * fs-reclaim safe - the mutex is taken when evicting inodes.
+	 */
+	if (flags & FSNOTIFY_GROUP_NOFS)
+		lockdep_set_class(&group->mark_mutex, &nofs_marks_lock);
 
 	return group;
 }
@@ -140,20 +154,15 @@
 /*
  * Create a new fsnotify_group and hold a reference for the group returned.
  */
-struct fsnotify_group *fsnotify_alloc_group(const struct fsnotify_ops *ops)
+struct fsnotify_group *fsnotify_alloc_group(const struct fsnotify_ops *ops,
+					    int flags)
 {
-	return __fsnotify_alloc_group(ops, GFP_KERNEL);
-}
-EXPORT_SYMBOL_GPL(fsnotify_alloc_group);
+	gfp_t gfp = (flags & FSNOTIFY_GROUP_USER) ? GFP_KERNEL_ACCOUNT :
+						    GFP_KERNEL;
 
-/*
- * Create a new fsnotify_group and hold a reference for the group returned.
- */
-struct fsnotify_group *fsnotify_alloc_user_group(const struct fsnotify_ops *ops)
-{
-	return __fsnotify_alloc_group(ops, GFP_KERNEL_ACCOUNT);
+	return __fsnotify_alloc_group(ops, flags, gfp);
 }
-EXPORT_SYMBOL_GPL(fsnotify_alloc_user_group);
+EXPORT_SYMBOL_GPL(fsnotify_alloc_group);
 
 int fsnotify_fasync(int fd, struct file *file, int on)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/inotify/inotify.h
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/inotify/inotify.h
@@ -22,6 +22,25 @@
 	return container_of(fse, struct inotify_event_info, fse);
 }
 
+/*
+ * INOTIFY_USER_FLAGS represents all of the mask bits that we expose to
+ * userspace.  There is at least one bit (FS_EVENT_ON_CHILD) which is
+ * used only internally to the kernel.
+ */
+#define INOTIFY_USER_MASK (IN_ALL_EVENTS)
+
+static inline __u32 inotify_mark_user_mask(struct fsnotify_mark *fsn_mark)
+{
+	__u32 mask = fsn_mark->mask & INOTIFY_USER_MASK;
+
+	if (fsn_mark->flags & FSNOTIFY_MARK_FLAG_EXCL_UNLINK)
+		mask |= IN_EXCL_UNLINK;
+	if (fsn_mark->flags & FSNOTIFY_MARK_FLAG_IN_ONESHOT)
+		mask |= IN_ONESHOT;
+
+	return mask;
+}
+
 extern void inotify_ignored_and_remove_idr(struct fsnotify_mark *fsn_mark,
 					   struct fsnotify_group *group);
 extern int inotify_handle_inode_event(struct fsnotify_mark *inode_mark,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/inotify/inotify_fsnotify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/inotify/inotify_fsnotify.c
@@ -65,7 +65,7 @@
 	struct fsnotify_event *fsn_event;
 	struct fsnotify_group *group = inode_mark->group;
 	int ret;
-	int len = 0;
+	int len = 0, wd;
 	int alloc_len = sizeof(struct inotify_event_info);
 	struct mem_cgroup *old_memcg;
 
@@ -81,6 +81,13 @@
 			      fsn_mark);
 
 	/*
+	 * We can be racing with mark being detached. Don't report event with
+	 * invalid wd.
+	 */
+	wd = READ_ONCE(i_mark->wd);
+	if (wd == -1)
+		return 0;
+	/*
 	 * Whoever is interested in the event, pays for the allocation. Do not
 	 * trigger OOM killer in the target monitoring memcg as it may have
 	 * security repercussion.
@@ -110,19 +117,19 @@
 	fsn_event = &event->fse;
 	fsnotify_init_event(fsn_event);
 	event->mask = mask;
-	event->wd = i_mark->wd;
+	event->wd = wd;
 	event->sync_cookie = cookie;
 	event->name_len = len;
 	if (len)
 		strcpy(event->name, name->name);
 
-	ret = fsnotify_add_event(group, fsn_event, inotify_merge, NULL);
+	ret = fsnotify_add_event(group, fsn_event, inotify_merge);
 	if (ret) {
 		/* Our event wasn't used in the end. Free it. */
 		fsnotify_destroy_event(group, fsn_event);
 	}
 
-	if (inode_mark->mask & IN_ONESHOT)
+	if (inode_mark->flags & FSNOTIFY_MARK_FLAG_IN_ONESHOT)
 		fsnotify_destroy_mark(inode_mark, group);
 
 	return 0;
@@ -177,7 +184,8 @@
 		dec_inotify_instances(group->inotify_data.ucounts);
 }
 
-static void inotify_free_event(struct fsnotify_event *fsn_event)
+static void inotify_free_event(struct fsnotify_group *group,
+			       struct fsnotify_event *fsn_event)
 {
 	kfree(INOTIFY_E(fsn_event));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/inotify/inotify_user.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/inotify/inotify_user.c
@@ -94,26 +94,41 @@
 	__u32 mask;
 
 	/*
-	 * Everything should accept their own ignored and should receive events
-	 * when the inode is unmounted.  All directories care about children.
+	 * Everything should receive events when the inode is unmounted.
+	 * All directories care about children.
 	 */
-	mask = (FS_IN_IGNORED | FS_UNMOUNT);
+	mask = (FS_UNMOUNT);
 	if (S_ISDIR(inode->i_mode))
 		mask |= FS_EVENT_ON_CHILD;
 
 	/* mask off the flags used to open the fd */
-	mask |= (arg & (IN_ALL_EVENTS | IN_ONESHOT | IN_EXCL_UNLINK));
+	mask |= (arg & INOTIFY_USER_MASK);
 
 	return mask;
 }
 
+#define INOTIFY_MARK_FLAGS \
+	(FSNOTIFY_MARK_FLAG_EXCL_UNLINK | FSNOTIFY_MARK_FLAG_IN_ONESHOT)
+
+static inline unsigned int inotify_arg_to_flags(u32 arg)
+{
+	unsigned int flags = 0;
+
+	if (arg & IN_EXCL_UNLINK)
+		flags |= FSNOTIFY_MARK_FLAG_EXCL_UNLINK;
+	if (arg & IN_ONESHOT)
+		flags |= FSNOTIFY_MARK_FLAG_IN_ONESHOT;
+
+	return flags;
+}
+
 static inline u32 inotify_mask_to_arg(__u32 mask)
 {
 	return mask & (IN_ALL_EVENTS | IN_ISDIR | IN_UNMOUNT | IN_IGNORED |
 		       IN_Q_OVERFLOW);
 }
 
-/* intofiy userspace file descriptor functions */
+/* inotify userspace file descriptor functions */
 static __poll_t inotify_poll(struct file *file, poll_table *wait)
 {
 	struct fsnotify_group *group = file->private_data;
@@ -518,13 +533,10 @@
 	struct fsnotify_mark *fsn_mark;
 	struct inotify_inode_mark *i_mark;
 	__u32 old_mask, new_mask;
-	__u32 mask;
-	int add = (arg & IN_MASK_ADD);
+	int replace = !(arg & IN_MASK_ADD);
 	int create = (arg & IN_MASK_CREATE);
 	int ret;
 
-	mask = inotify_arg_to_mask(inode, arg);
-
 	fsn_mark = fsnotify_find_mark(&inode->i_fsnotify_marks, group);
 	if (!fsn_mark)
 		return -ENOENT;
@@ -537,10 +549,12 @@
 
 	spin_lock(&fsn_mark->lock);
 	old_mask = fsn_mark->mask;
-	if (add)
-		fsn_mark->mask |= mask;
-	else
-		fsn_mark->mask = mask;
+	if (replace) {
+		fsn_mark->mask = 0;
+		fsn_mark->flags &= ~INOTIFY_MARK_FLAGS;
+	}
+	fsn_mark->mask |= inotify_arg_to_mask(inode, arg);
+	fsn_mark->flags |= inotify_arg_to_flags(arg);
 	new_mask = fsn_mark->mask;
 	spin_unlock(&fsn_mark->lock);
 
@@ -571,19 +585,17 @@
 			     u32 arg)
 {
 	struct inotify_inode_mark *tmp_i_mark;
-	__u32 mask;
 	int ret;
 	struct idr *idr = &group->inotify_data.idr;
 	spinlock_t *idr_lock = &group->inotify_data.idr_lock;
 
-	mask = inotify_arg_to_mask(inode, arg);
-
 	tmp_i_mark = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL);
 	if (unlikely(!tmp_i_mark))
 		return -ENOMEM;
 
 	fsnotify_init_mark(&tmp_i_mark->fsn_mark, group);
-	tmp_i_mark->fsn_mark.mask = mask;
+	tmp_i_mark->fsn_mark.mask = inotify_arg_to_mask(inode, arg);
+	tmp_i_mark->fsn_mark.flags = inotify_arg_to_flags(arg);
 	tmp_i_mark->wd = -1;
 
 	ret = inotify_add_to_idr(idr, idr_lock, tmp_i_mark);
@@ -620,13 +632,13 @@
 {
 	int ret = 0;
 
-	mutex_lock(&group->mark_mutex);
+	fsnotify_group_lock(group);
 	/* try to update and existing watch with the new arg */
 	ret = inotify_update_existing_watch(group, inode, arg);
 	/* no mark present, try to add a new one */
 	if (ret == -ENOENT)
 		ret = inotify_new_watch(group, inode, arg);
-	mutex_unlock(&group->mark_mutex);
+	fsnotify_group_unlock(group);
 
 	return ret;
 }
@@ -636,7 +648,8 @@
 	struct fsnotify_group *group;
 	struct inotify_event_info *oevent;
 
-	group = fsnotify_alloc_user_group(&inotify_fsnotify_ops);
+	group = fsnotify_alloc_group(&inotify_fsnotify_ops,
+				     FSNOTIFY_GROUP_USER);
 	if (IS_ERR(group))
 		return group;
 
@@ -837,9 +850,7 @@
 	BUILD_BUG_ON(IN_UNMOUNT != FS_UNMOUNT);
 	BUILD_BUG_ON(IN_Q_OVERFLOW != FS_Q_OVERFLOW);
 	BUILD_BUG_ON(IN_IGNORED != FS_IN_IGNORED);
-	BUILD_BUG_ON(IN_EXCL_UNLINK != FS_EXCL_UNLINK);
 	BUILD_BUG_ON(IN_ISDIR != FS_ISDIR);
-	BUILD_BUG_ON(IN_ONESHOT != FS_IN_ONESHOT);
 
 	BUILD_BUG_ON(HWEIGHT32(ALL_INOTIFY_BITS) != 22);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/mark.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/mark.c
@@ -116,20 +116,82 @@
 	return *fsnotify_conn_mask_p(conn);
 }
 
-static void __fsnotify_recalc_mask(struct fsnotify_mark_connector *conn)
+static void fsnotify_get_inode_ref(struct inode *inode)
+{
+	ihold(inode);
+	atomic_long_inc(&inode->i_sb->s_fsnotify_connectors);
+}
+
+/*
+ * Grab or drop inode reference for the connector if needed.
+ *
+ * When it's time to drop the reference, we only clear the HAS_IREF flag and
+ * return the inode object. fsnotify_drop_object() will be resonsible for doing
+ * iput() outside of spinlocks. This happens when last mark that wanted iref is
+ * detached.
+ */
+static struct inode *fsnotify_update_iref(struct fsnotify_mark_connector *conn,
+					  bool want_iref)
+{
+	bool has_iref = conn->flags & FSNOTIFY_CONN_FLAG_HAS_IREF;
+	struct inode *inode = NULL;
+
+	if (conn->type != FSNOTIFY_OBJ_TYPE_INODE ||
+	    want_iref == has_iref)
+		return NULL;
+
+	if (want_iref) {
+		/* Pin inode if any mark wants inode refcount held */
+		fsnotify_get_inode_ref(fsnotify_conn_inode(conn));
+		conn->flags |= FSNOTIFY_CONN_FLAG_HAS_IREF;
+	} else {
+		/* Unpin inode after detach of last mark that wanted iref */
+		inode = fsnotify_conn_inode(conn);
+		conn->flags &= ~FSNOTIFY_CONN_FLAG_HAS_IREF;
+	}
+
+	return inode;
+}
+
+static void *__fsnotify_recalc_mask(struct fsnotify_mark_connector *conn)
 {
 	u32 new_mask = 0;
+	bool want_iref = false;
 	struct fsnotify_mark *mark;
 
 	assert_spin_locked(&conn->lock);
 	/* We can get detached connector here when inode is getting unlinked. */
 	if (!fsnotify_valid_obj_type(conn->type))
-		return;
+		return NULL;
 	hlist_for_each_entry(mark, &conn->list, obj_list) {
-		if (mark->flags & FSNOTIFY_MARK_FLAG_ATTACHED)
-			new_mask |= mark->mask;
+		if (!(mark->flags & FSNOTIFY_MARK_FLAG_ATTACHED))
+			continue;
+		new_mask |= fsnotify_calc_mask(mark);
+		if (conn->type == FSNOTIFY_OBJ_TYPE_INODE &&
+		    !(mark->flags & FSNOTIFY_MARK_FLAG_NO_IREF))
+			want_iref = true;
 	}
 	*fsnotify_conn_mask_p(conn) = new_mask;
+
+	return fsnotify_update_iref(conn, want_iref);
+}
+
+static bool fsnotify_conn_watches_children(
+					struct fsnotify_mark_connector *conn)
+{
+	if (conn->type != FSNOTIFY_OBJ_TYPE_INODE)
+		return false;
+
+	return fsnotify_inode_watches_children(fsnotify_conn_inode(conn));
+}
+
+static void fsnotify_conn_set_children_dentry_flags(
+					struct fsnotify_mark_connector *conn)
+{
+	if (conn->type != FSNOTIFY_OBJ_TYPE_INODE)
+		return;
+
+	fsnotify_set_children_dentry_flags(fsnotify_conn_inode(conn));
 }
 
 /*
@@ -140,15 +202,23 @@
  */
 void fsnotify_recalc_mask(struct fsnotify_mark_connector *conn)
 {
+	bool update_children;
+
 	if (!conn)
 		return;
 
 	spin_lock(&conn->lock);
+	update_children = !fsnotify_conn_watches_children(conn);
 	__fsnotify_recalc_mask(conn);
+	update_children &= fsnotify_conn_watches_children(conn);
 	spin_unlock(&conn->lock);
-	if (conn->type == FSNOTIFY_OBJ_TYPE_INODE)
-		__fsnotify_update_child_dentry_flags(
-					fsnotify_conn_inode(conn));
+	/*
+	 * Set children's PARENT_WATCHED flags only if parent started watching.
+	 * When parent stops watching, we clear false positive PARENT_WATCHED
+	 * flags lazily in __fsnotify_parent().
+	 */
+	if (update_children)
+		fsnotify_conn_set_children_dentry_flags(conn);
 }
 
 /* Free all connectors queued for freeing once SRCU period ends */
@@ -169,12 +239,6 @@
 	}
 }
 
-static void fsnotify_get_inode_ref(struct inode *inode)
-{
-	ihold(inode);
-	atomic_long_inc(&inode->i_sb->s_fsnotify_connectors);
-}
-
 static void fsnotify_put_inode_ref(struct inode *inode)
 {
 	struct super_block *sb = inode->i_sb;
@@ -213,6 +277,10 @@
 	if (conn->type == FSNOTIFY_OBJ_TYPE_INODE) {
 		inode = fsnotify_conn_inode(conn);
 		inode->i_fsnotify_mask = 0;
+
+		/* Unpin inode when detaching from connector */
+		if (!(conn->flags & FSNOTIFY_CONN_FLAG_HAS_IREF))
+			inode = NULL;
 	} else if (conn->type == FSNOTIFY_OBJ_TYPE_VFSMOUNT) {
 		fsnotify_conn_mount(conn)->mnt_fsnotify_mask = 0;
 	} else if (conn->type == FSNOTIFY_OBJ_TYPE_SB) {
@@ -274,7 +342,8 @@
 		objp = fsnotify_detach_connector_from_object(conn, &type);
 		free_conn = true;
 	} else {
-		__fsnotify_recalc_mask(conn);
+		objp = __fsnotify_recalc_mask(conn);
+		type = conn->type;
 	}
 	WRITE_ONCE(mark->connector, NULL);
 	spin_unlock(&conn->lock);
@@ -353,7 +422,7 @@
 {
 	int type;
 
-	fsnotify_foreach_obj_type(type) {
+	fsnotify_foreach_iter_type(type) {
 		/* This can fail if mark is being removed */
 		if (!fsnotify_get_mark_safe(iter_info->marks[type])) {
 			__release(&fsnotify_mark_srcu);
@@ -382,7 +451,7 @@
 	int type;
 
 	iter_info->srcu_idx = srcu_read_lock(&fsnotify_mark_srcu);
-	fsnotify_foreach_obj_type(type)
+	fsnotify_foreach_iter_type(type)
 		fsnotify_put_mark_wake(iter_info->marks[type]);
 }
 
@@ -398,9 +467,7 @@
  */
 void fsnotify_detach_mark(struct fsnotify_mark *mark)
 {
-	struct fsnotify_group *group = mark->group;
-
-	WARN_ON_ONCE(!mutex_is_locked(&group->mark_mutex));
+	fsnotify_group_assert_locked(mark->group);
 	WARN_ON_ONCE(!srcu_read_lock_held(&fsnotify_mark_srcu) &&
 		     refcount_read(&mark->refcnt) < 1 +
 			!!(mark->flags & FSNOTIFY_MARK_FLAG_ATTACHED));
@@ -452,9 +519,9 @@
 void fsnotify_destroy_mark(struct fsnotify_mark *mark,
 			   struct fsnotify_group *group)
 {
-	mutex_lock_nested(&group->mark_mutex, SINGLE_DEPTH_NESTING);
+	fsnotify_group_lock(group);
 	fsnotify_detach_mark(mark);
-	mutex_unlock(&group->mark_mutex);
+	fsnotify_group_unlock(group);
 	fsnotify_free_mark(mark);
 }
 EXPORT_SYMBOL_GPL(fsnotify_destroy_mark);
@@ -496,10 +563,9 @@
 }
 
 static int fsnotify_attach_connector_to_object(fsnotify_connp_t *connp,
-					       unsigned int type,
+					       unsigned int obj_type,
 					       __kernel_fsid_t *fsid)
 {
-	struct inode *inode = NULL;
 	struct fsnotify_mark_connector *conn;
 
 	conn = kmem_cache_alloc(fsnotify_mark_connector_cachep, GFP_KERNEL);
@@ -507,7 +573,8 @@
 		return -ENOMEM;
 	spin_lock_init(&conn->lock);
 	INIT_HLIST_HEAD(&conn->list);
-	conn->type = type;
+	conn->flags = 0;
+	conn->type = obj_type;
 	conn->obj = connp;
 	/* Cache fsid of filesystem containing the object */
 	if (fsid) {
@@ -517,10 +584,6 @@
 		conn->fsid.val[0] = conn->fsid.val[1] = 0;
 		conn->flags = 0;
 	}
-	if (conn->type == FSNOTIFY_OBJ_TYPE_INODE) {
-		inode = fsnotify_conn_inode(conn);
-		fsnotify_get_inode_ref(inode);
-	}
 	fsnotify_get_sb_connectors(conn);
 
 	/*
@@ -529,8 +592,6 @@
 	 */
 	if (cmpxchg(connp, NULL, conn)) {
 		/* Someone else created list structure for us */
-		if (inode)
-			fsnotify_put_inode_ref(inode);
 		fsnotify_put_sb_connectors(conn);
 		kmem_cache_free(fsnotify_mark_connector_cachep, conn);
 	}
@@ -572,15 +633,16 @@
  * priority, highest number first, and then by the group's location in memory.
  */
 static int fsnotify_add_mark_list(struct fsnotify_mark *mark,
-				  fsnotify_connp_t *connp, unsigned int type,
-				  int allow_dups, __kernel_fsid_t *fsid)
+				  fsnotify_connp_t *connp,
+				  unsigned int obj_type,
+				  int add_flags, __kernel_fsid_t *fsid)
 {
 	struct fsnotify_mark *lmark, *last = NULL;
 	struct fsnotify_mark_connector *conn;
 	int cmp;
 	int err = 0;
 
-	if (WARN_ON(!fsnotify_valid_obj_type(type)))
+	if (WARN_ON(!fsnotify_valid_obj_type(obj_type)))
 		return -EINVAL;
 
 	/* Backend is expected to check for zero fsid (e.g. tmpfs) */
@@ -592,7 +654,8 @@
 	conn = fsnotify_grab_connector(connp);
 	if (!conn) {
 		spin_unlock(&mark->lock);
-		err = fsnotify_attach_connector_to_object(connp, type, fsid);
+		err = fsnotify_attach_connector_to_object(connp, obj_type,
+							  fsid);
 		if (err)
 			return err;
 		goto restart;
@@ -631,7 +694,7 @@
 
 		if ((lmark->group == mark->group) &&
 		    (lmark->flags & FSNOTIFY_MARK_FLAG_ATTACHED) &&
-		    !allow_dups) {
+		    !(mark->group->flags & FSNOTIFY_GROUP_DUPS)) {
 			err = -EEXIST;
 			goto out_err;
 		}
@@ -665,13 +728,13 @@
  * event types should be delivered to which group.
  */
 int fsnotify_add_mark_locked(struct fsnotify_mark *mark,
-			     fsnotify_connp_t *connp, unsigned int type,
-			     int allow_dups, __kernel_fsid_t *fsid)
+			     fsnotify_connp_t *connp, unsigned int obj_type,
+			     int add_flags, __kernel_fsid_t *fsid)
 {
 	struct fsnotify_group *group = mark->group;
 	int ret = 0;
 
-	BUG_ON(!mutex_is_locked(&group->mark_mutex));
+	fsnotify_group_assert_locked(group);
 
 	/*
 	 * LOCKING ORDER!!!!
@@ -686,12 +749,11 @@
 	fsnotify_get_mark(mark); /* for g_list */
 	spin_unlock(&mark->lock);
 
-	ret = fsnotify_add_mark_list(mark, connp, type, allow_dups, fsid);
+	ret = fsnotify_add_mark_list(mark, connp, obj_type, add_flags, fsid);
 	if (ret)
 		goto err;
 
-	if (mark->mask)
-		fsnotify_recalc_mask(mark->connector);
+	fsnotify_recalc_mask(mark->connector);
 
 	return ret;
 err:
@@ -706,14 +768,15 @@
 }
 
 int fsnotify_add_mark(struct fsnotify_mark *mark, fsnotify_connp_t *connp,
-		      unsigned int type, int allow_dups, __kernel_fsid_t *fsid)
+		      unsigned int obj_type, int add_flags,
+		      __kernel_fsid_t *fsid)
 {
 	int ret;
 	struct fsnotify_group *group = mark->group;
 
-	mutex_lock(&group->mark_mutex);
-	ret = fsnotify_add_mark_locked(mark, connp, type, allow_dups, fsid);
-	mutex_unlock(&group->mark_mutex);
+	fsnotify_group_lock(group);
+	ret = fsnotify_add_mark_locked(mark, connp, obj_type, add_flags, fsid);
+	fsnotify_group_unlock(group);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(fsnotify_add_mark);
@@ -747,14 +810,14 @@
 
 /* Clear any marks in a group with given type mask */
 void fsnotify_clear_marks_by_group(struct fsnotify_group *group,
-				   unsigned int type_mask)
+				   unsigned int obj_type)
 {
 	struct fsnotify_mark *lmark, *mark;
 	LIST_HEAD(to_free);
 	struct list_head *head = &to_free;
 
 	/* Skip selection step if we want to clear all marks. */
-	if (type_mask == FSNOTIFY_OBJ_ALL_TYPES_MASK) {
+	if (obj_type == FSNOTIFY_OBJ_TYPE_ANY) {
 		head = &group->marks_list;
 		goto clear;
 	}
@@ -767,24 +830,24 @@
 	 * move marks to free to to_free list in one go and then free marks in
 	 * to_free list one by one.
 	 */
-	mutex_lock_nested(&group->mark_mutex, SINGLE_DEPTH_NESTING);
+	fsnotify_group_lock(group);
 	list_for_each_entry_safe(mark, lmark, &group->marks_list, g_list) {
-		if ((1U << mark->connector->type) & type_mask)
+		if (mark->connector->type == obj_type)
 			list_move(&mark->g_list, &to_free);
 	}
-	mutex_unlock(&group->mark_mutex);
+	fsnotify_group_unlock(group);
 
 clear:
 	while (1) {
-		mutex_lock_nested(&group->mark_mutex, SINGLE_DEPTH_NESTING);
+		fsnotify_group_lock(group);
 		if (list_empty(head)) {
-			mutex_unlock(&group->mark_mutex);
+			fsnotify_group_unlock(group);
 			break;
 		}
 		mark = list_first_entry(head, struct fsnotify_mark, g_list);
 		fsnotify_get_mark(mark);
 		fsnotify_detach_mark(mark);
-		mutex_unlock(&group->mark_mutex);
+		fsnotify_group_unlock(group);
 		fsnotify_free_mark(mark);
 		fsnotify_put_mark(mark);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/notify/notification.c
+++ linux-xilinx-zynqmp-5.15.0/fs/notify/notification.c
@@ -64,7 +64,7 @@
 		WARN_ON(!list_empty(&event->list));
 		spin_unlock(&group->notification_lock);
 	}
-	group->ops->free_event(event);
+	group->ops->free_event(group, event);
 }
 
 /*
@@ -78,12 +78,12 @@
  * 2 if the event was not queued - either the queue of events has overflown
  *   or the group is shutting down.
  */
-int fsnotify_add_event(struct fsnotify_group *group,
-		       struct fsnotify_event *event,
-		       int (*merge)(struct fsnotify_group *,
-				    struct fsnotify_event *),
-		       void (*insert)(struct fsnotify_group *,
-				      struct fsnotify_event *))
+int fsnotify_insert_event(struct fsnotify_group *group,
+			  struct fsnotify_event *event,
+			  int (*merge)(struct fsnotify_group *,
+				       struct fsnotify_event *),
+			  void (*insert)(struct fsnotify_group *,
+					 struct fsnotify_event *))
 {
 	int ret = 0;
 	struct list_head *list = &group->notification_list;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs/attrib.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs/attrib.c
@@ -592,15 +592,39 @@
 		a = (ATTR_RECORD*)((u8*)ctx->attr +
 				le32_to_cpu(ctx->attr->length));
 	for (;;	a = (ATTR_RECORD*)((u8*)a + le32_to_cpu(a->length))) {
-		if ((u8*)a < (u8*)ctx->mrec || (u8*)a > (u8*)ctx->mrec +
-				le32_to_cpu(ctx->mrec->bytes_allocated))
+		u8 *mrec_end = (u8 *)ctx->mrec +
+		               le32_to_cpu(ctx->mrec->bytes_allocated);
+		u8 *name_end;
+
+		/* check whether ATTR_RECORD wrap */
+		if ((u8 *)a < (u8 *)ctx->mrec)
 			break;
+
+		/* check whether Attribute Record Header is within bounds */
+		if ((u8 *)a > mrec_end ||
+		    (u8 *)a + sizeof(ATTR_RECORD) > mrec_end)
+			break;
+
+		/* check whether ATTR_RECORD's name is within bounds */
+		name_end = (u8 *)a + le16_to_cpu(a->name_offset) +
+			   a->name_length * sizeof(ntfschar);
+		if (name_end > mrec_end)
+			break;
+
 		ctx->attr = a;
 		if (unlikely(le32_to_cpu(a->type) > le32_to_cpu(type) ||
 				a->type == AT_END))
 			return -ENOENT;
 		if (unlikely(!a->length))
 			break;
+
+		/* check whether ATTR_RECORD's length wrap */
+		if ((u8 *)a + le32_to_cpu(a->length) < (u8 *)a)
+			break;
+		/* check whether ATTR_RECORD's length is within bounds */
+		if ((u8 *)a + le32_to_cpu(a->length) > mrec_end)
+			break;
+
 		if (a->type != type)
 			continue;
 		/*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs/file.c
@@ -1829,7 +1829,7 @@
 		 * pages being swapped out between us bringing them into memory
 		 * and doing the actual copying.
 		 */
-		if (unlikely(iov_iter_fault_in_readable(i, bytes))) {
+		if (unlikely(fault_in_iov_iter_readable(i, bytes))) {
 			status = -EFAULT;
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs/inode.c
@@ -1829,6 +1829,13 @@
 		goto err_out;
 	}
 
+	/* Sanity check offset to the first attribute */
+	if (le16_to_cpu(m->attrs_offset) >= le32_to_cpu(m->bytes_allocated)) {
+		ntfs_error(sb, "Incorrect mft offset to the first attribute %u in superblock.",
+			       le16_to_cpu(m->attrs_offset));
+		goto err_out;
+	}
+
 	/* Need this to sanity check attribute list references to $MFT. */
 	vi->i_generation = ni->seq_no = le16_to_cpu(m->sequence_number);
 
@@ -1881,6 +1888,10 @@
 		}
 		/* Now allocate memory for the attribute list. */
 		ni->attr_list_size = (u32)ntfs_attr_size(a);
+		if (!ni->attr_list_size) {
+			ntfs_error(sb, "Attr_list_size is zero");
+			goto put_err_out;
+		}
 		ni->attr_list = ntfs_malloc_nofs(ni->attr_list_size);
 		if (!ni->attr_list) {
 			ntfs_error(sb, "Not enough memory to allocate buffer "
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs/super.c
@@ -2092,7 +2092,8 @@
 	// TODO: Initialize security.
 	/* Get the extended system files' directory inode. */
 	vol->extend_ino = ntfs_iget(sb, FILE_Extend);
-	if (IS_ERR(vol->extend_ino) || is_bad_inode(vol->extend_ino)) {
+	if (IS_ERR(vol->extend_ino) || is_bad_inode(vol->extend_ino) ||
+	    !S_ISDIR(vol->extend_ino->i_mode)) {
 		if (!IS_ERR(vol->extend_ino))
 			iput(vol->extend_ino);
 		ntfs_error(sb, "Failed to load $Extend.");
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/attrib.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/attrib.c
@@ -101,6 +101,10 @@
 
 	asize = le32_to_cpu(attr->size);
 	run_off = le16_to_cpu(attr->nres.run_off);
+
+	if (run_off > asize)
+		return -EINVAL;
+
 	err = run_unpack_ex(run, ni->mi.sbi, ni->mi.rno, svcn, evcn,
 			    vcn ? *vcn : svcn, Add2Ptr(attr, run_off),
 			    asize - run_off);
@@ -238,7 +242,7 @@
 	struct ntfs_sb_info *sbi;
 	struct ATTRIB *attr_s;
 	struct MFT_REC *rec;
-	u32 used, asize, rsize, aoff, align;
+	u32 used, asize, rsize, aoff;
 	bool is_data;
 	CLST len, alen;
 	char *next;
@@ -259,10 +263,13 @@
 	rsize = le32_to_cpu(attr->res.data_size);
 	is_data = attr->type == ATTR_DATA && !attr->name_len;
 
-	align = sbi->cluster_size;
-	if (is_attr_compressed(attr))
-		align <<= COMPRESSION_UNIT;
-	len = (rsize + align - 1) >> sbi->cluster_bits;
+	/* len - how many clusters required to store 'rsize' bytes */
+	if (is_attr_compressed(attr)) {
+		u8 shift = sbi->cluster_bits + NTFS_LZNT_CUNIT;
+		len = ((rsize + (1u << shift) - 1) >> shift) << NTFS_LZNT_CUNIT;
+	} else {
+		len = bytes_to_cluster(sbi, rsize);
+	}
 
 	run_init(run);
 
@@ -1142,6 +1149,11 @@
 	CLST svcn, evcn;
 	u16 ro;
 
+	if (!ni) {
+		/* Is record corrupted? */
+		return -ENOENT;
+	}
+
 	attr = ni_find_attr(ni, NULL, NULL, type, name, name_len, &vcn, NULL);
 	if (!attr) {
 		/* Is record corrupted? */
@@ -1157,6 +1169,10 @@
 	}
 
 	ro = le16_to_cpu(attr->nres.run_off);
+
+	if (ro > le32_to_cpu(attr->size))
+		return -EINVAL;
+
 	err = run_unpack_ex(run, ni->mi.sbi, ni->mi.rno, svcn, evcn, svcn,
 			    Add2Ptr(attr, ro), le32_to_cpu(attr->size) - ro);
 	if (err < 0)
@@ -1549,6 +1565,7 @@
 
 	attr_b->nres.total_size = cpu_to_le64(total_size);
 	inode_set_bytes(&ni->vfs_inode, total_size);
+	ni->ni_flags |= NI_FLAG_UPDATE_PARENT;
 
 	mi_b->dirty = true;
 	mark_inode_dirty(&ni->vfs_inode);
@@ -1654,13 +1671,15 @@
 ok:
 	run_truncate_around(run, vcn);
 out:
-	if (new_valid > data_size)
-		new_valid = data_size;
-
-	valid_size = le64_to_cpu(attr_b->nres.valid_size);
-	if (new_valid != valid_size) {
-		attr_b->nres.valid_size = cpu_to_le64(valid_size);
-		mi_b->dirty = true;
+	if (attr_b) {
+		if (new_valid > data_size)
+			new_valid = data_size;
+
+		valid_size = le64_to_cpu(attr_b->nres.valid_size);
+		if (new_valid != valid_size) {
+			attr_b->nres.valid_size = cpu_to_le64(valid_size);
+			mi_b->dirty = true;
+		}
 	}
 
 	return err;
@@ -1832,6 +1851,11 @@
 			u16 le_sz;
 			u16 roff = le16_to_cpu(attr->nres.run_off);
 
+			if (roff > le32_to_cpu(attr->size)) {
+				err = -EINVAL;
+				goto out;
+			}
+
 			run_unpack_ex(RUN_DEALLOCATE, sbi, ni->mi.rno, svcn,
 				      evcn1 - 1, svcn, Add2Ptr(attr, roff),
 				      le32_to_cpu(attr->size) - roff);
@@ -1949,7 +1973,7 @@
 		return -ENOENT;
 
 	if (!attr_b->non_res) {
-		u32 data_size = le32_to_cpu(attr->res.data_size);
+		u32 data_size = le32_to_cpu(attr_b->res.data_size);
 		u32 from, to;
 
 		if (vbo > data_size)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/attrlist.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/attrlist.c
@@ -29,7 +29,7 @@
 void al_destroy(struct ntfs_inode *ni)
 {
 	run_close(&ni->attr_list.run);
-	kfree(ni->attr_list.le);
+	kvfree(ni->attr_list.le);
 	ni->attr_list.le = NULL;
 	ni->attr_list.size = 0;
 	ni->attr_list.dirty = false;
@@ -52,7 +52,8 @@
 
 	if (!attr->non_res) {
 		lsize = le32_to_cpu(attr->res.data_size);
-		le = kmalloc(al_aligned(lsize), GFP_NOFS);
+		/* attr is resident: lsize < record_size (1K or 4K) */
+		le = kvmalloc(al_aligned(lsize), GFP_KERNEL);
 		if (!le) {
 			err = -ENOMEM;
 			goto out;
@@ -68,6 +69,11 @@
 
 		run_init(&ni->attr_list.run);
 
+		if (run_off > le32_to_cpu(attr->size)) {
+			err = -EINVAL;
+			goto out;
+		}
+
 		err = run_unpack_ex(&ni->attr_list.run, ni->mi.sbi, ni->mi.rno,
 				    0, le64_to_cpu(attr->nres.evcn), 0,
 				    Add2Ptr(attr, run_off),
@@ -75,7 +81,17 @@
 		if (err < 0)
 			goto out;
 
-		le = kmalloc(al_aligned(lsize), GFP_NOFS);
+		/* attr is nonresident.
+		 * The worst case:
+		 * 1T (2^40) extremely fragmented file.
+		 * cluster = 4K (2^12) => 2^28 fragments
+		 * 2^9 fragments per one record => 2^19 records
+		 * 2^5 bytes of ATTR_LIST_ENTRY per one record => 2^24 bytes.
+		 *
+		 * the result is 16M bytes per attribute list.
+		 * Use kvmalloc to allocate in range [several Kbytes - dozen Mbytes]
+		 */
+		le = kvmalloc(al_aligned(lsize), GFP_KERNEL);
 		if (!le) {
 			err = -ENOMEM;
 			goto out;
@@ -111,12 +127,13 @@
 {
 	size_t off;
 	u16 sz;
+	const unsigned le_min_size = le_size(0);
 
 	if (!le) {
 		le = ni->attr_list.le;
 	} else {
 		sz = le16_to_cpu(le->size);
-		if (sz < sizeof(struct ATTR_LIST_ENTRY)) {
+		if (sz < le_min_size) {
 			/* Impossible 'cause we should not return such le. */
 			return NULL;
 		}
@@ -125,7 +142,7 @@
 
 	/* Check boundary. */
 	off = PtrOffset(ni->attr_list.le, le);
-	if (off + sizeof(struct ATTR_LIST_ENTRY) > ni->attr_list.size) {
+	if (off + le_min_size > ni->attr_list.size) {
 		/* The regular end of list. */
 		return NULL;
 	}
@@ -133,8 +150,7 @@
 	sz = le16_to_cpu(le->size);
 
 	/* Check le for errors. */
-	if (sz < sizeof(struct ATTR_LIST_ENTRY) ||
-	    off + sz > ni->attr_list.size ||
+	if (sz < le_min_size || off + sz > ni->attr_list.size ||
 	    sz < le->name_off + le->name_len * sizeof(short)) {
 		return NULL;
 	}
@@ -302,7 +318,7 @@
 		memcpy(ptr, al->le, off);
 		memcpy(Add2Ptr(ptr, off + sz), le, old_size - off);
 		le = Add2Ptr(ptr, off);
-		kfree(al->le);
+		kvfree(al->le);
 		al->le = ptr;
 	} else {
 		memmove(Add2Ptr(le, sz), le, old_size - off);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/bitmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/bitmap.c
@@ -129,7 +129,7 @@
 {
 	struct rb_node *node, *next;
 
-	kfree(wnd->free_bits);
+	kvfree(wnd->free_bits);
 	run_close(&wnd->run);
 
 	node = rb_first(&wnd->start_tree);
@@ -661,12 +661,14 @@
 	wnd->total_zeroes = nbits;
 	wnd->extent_max = MINUS_ONE_T;
 	wnd->zone_bit = wnd->zone_end = 0;
-	wnd->nwnd = bytes_to_block(sb, bitmap_size(nbits));
+	wnd->nwnd = bytes_to_block(sb, ntfs3_bitmap_size(nbits));
 	wnd->bits_last = nbits & (wbits - 1);
 	if (!wnd->bits_last)
 		wnd->bits_last = wbits;
 
-	wnd->free_bits = kcalloc(wnd->nwnd, sizeof(u16), GFP_NOFS);
+	wnd->free_bits =
+		kvmalloc_array(wnd->nwnd, sizeof(u16), GFP_KERNEL | __GFP_ZERO);
+
 	if (!wnd->free_bits)
 		return -ENOMEM;
 
@@ -1323,7 +1325,7 @@
 		return -EINVAL;
 
 	/* Align to 8 byte boundary. */
-	new_wnd = bytes_to_block(sb, bitmap_size(new_bits));
+	new_wnd = bytes_to_block(sb, ntfs3_bitmap_size(new_bits));
 	new_last = new_bits & (wbits - 1);
 	if (!new_last)
 		new_last = wbits;
@@ -1338,7 +1340,7 @@
 			       wnd->nwnd * sizeof(short));
 		memset(new_free + wnd->nwnd, 0,
 		       (new_wnd - wnd->nwnd) * sizeof(short));
-		kfree(wnd->free_bits);
+		kvfree(wnd->free_bits);
 		wnd->free_bits = new_free;
 	}
 
@@ -1361,7 +1363,7 @@
 
 		err = ntfs_vbo_to_lbo(sbi, &wnd->run, vbo, &lbo, &bytes);
 		if (err)
-			break;
+			return err;
 
 		bh = ntfs_bread(sb, lbo >> sb->s_blocksize_bits);
 		if (!bh)
@@ -1432,7 +1434,7 @@
 
 	down_read_nested(&wnd->rw_lock, BITMAP_MUTEX_CLUSTERS);
 
-	for (; iw < wnd->nbits; iw++, wbit = 0) {
+	for (; iw < wnd->nwnd; iw++, wbit = 0) {
 		CLST lcn_wnd = iw * wbits;
 		struct buffer_head *bh;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/dir.c
@@ -272,9 +272,12 @@
 	return err == -ENOENT ? NULL : err ? ERR_PTR(err) : inode;
 }
 
-static inline int ntfs_filldir(struct ntfs_sb_info *sbi, struct ntfs_inode *ni,
-			       const struct NTFS_DE *e, u8 *name,
-			       struct dir_context *ctx)
+/*
+ * returns false if 'ctx' if full
+ */
+static inline bool ntfs_dir_emit(struct ntfs_sb_info *sbi,
+				 struct ntfs_inode *ni, const struct NTFS_DE *e,
+				 u8 *name, struct dir_context *ctx)
 {
 	const struct ATTR_FILE_NAME *fname;
 	unsigned long ino;
@@ -284,44 +287,72 @@
 	fname = Add2Ptr(e, sizeof(struct NTFS_DE));
 
 	if (fname->type == FILE_NAME_DOS)
-		return 0;
+		return true;
 
 	if (!mi_is_ref(&ni->mi, &fname->home))
-		return 0;
+		return true;
 
 	ino = ino_get(&e->ref);
 
 	if (ino == MFT_REC_ROOT)
-		return 0;
+		return true;
 
 	/* Skip meta files. Unless option to show metafiles is set. */
 	if (!sbi->options->showmeta && ntfs_is_meta_file(sbi, ino))
-		return 0;
+		return true;
 
 	if (sbi->options->nohidden && (fname->dup.fa & FILE_ATTRIBUTE_HIDDEN))
-		return 0;
+		return true;
 
 	name_len = ntfs_utf16_to_nls(sbi, fname->name, fname->name_len, name,
 				     PATH_MAX);
 	if (name_len <= 0) {
 		ntfs_warn(sbi->sb, "failed to convert name for inode %lx.",
 			  ino);
-		return 0;
+		return true;
 	}
 
+	/*
+	 * NTFS: symlinks are "dir + reparse" or "file + reparse"
+	 * Unfortunately reparse attribute is used for many purposes (several dozens).
+	 * It is not possible here to know is this name symlink or not.
+	 * To get exactly the type of name we should to open inode (read mft).
+	 * getattr for opened file (fstat) correctly returns symlink.
+	 */
 	dt_type = (fname->dup.fa & FILE_ATTRIBUTE_DIRECTORY) ? DT_DIR : DT_REG;
 
-	return !dir_emit(ctx, (s8 *)name, name_len, ino, dt_type);
+	/*
+	 * It is not reliable to detect the type of name using duplicated information
+	 * stored in parent directory.
+	 * The only correct way to get the type of name - read MFT record and find ATTR_STD.
+	 * The code below is not good idea.
+	 * It does additional locks/reads just to get the type of name.
+	 * Should we use additional mount option to enable branch below?
+	 */
+	if (((fname->dup.fa & FILE_ATTRIBUTE_REPARSE_POINT) ||
+	     fname->dup.ea_size) &&
+	    ino != ni->mi.rno) {
+		struct inode *inode = ntfs_iget5(sbi->sb, &e->ref, NULL);
+		if (!IS_ERR_OR_NULL(inode)) {
+			dt_type = fs_umode_to_dtype(inode->i_mode);
+			iput(inode);
+		}
+	}
+
+	return dir_emit(ctx, (s8 *)name, name_len, ino, dt_type);
 }
 
 /*
  * ntfs_read_hdr - Helper function for ntfs_readdir().
+ *
+ * returns 0 if ok.
+ * returns -EINVAL if directory is corrupted.
+ * returns +1 if 'ctx' is full.
  */
 static int ntfs_read_hdr(struct ntfs_sb_info *sbi, struct ntfs_inode *ni,
 			 const struct INDEX_HDR *hdr, u64 vbo, u64 pos,
 			 u8 *name, struct dir_context *ctx)
 {
-	int err;
 	const struct NTFS_DE *e;
 	u32 e_size;
 	u32 end = le32_to_cpu(hdr->used);
@@ -329,12 +360,12 @@
 
 	for (;; off += e_size) {
 		if (off + sizeof(struct NTFS_DE) > end)
-			return -1;
+			return -EINVAL;
 
 		e = Add2Ptr(hdr, off);
 		e_size = le16_to_cpu(e->size);
 		if (e_size < sizeof(struct NTFS_DE) || off + e_size > end)
-			return -1;
+			return -EINVAL;
 
 		if (de_is_last(e))
 			return 0;
@@ -344,14 +375,15 @@
 			continue;
 
 		if (le16_to_cpu(e->key_size) < SIZEOF_ATTRIBUTE_FILENAME)
-			return -1;
+			return -EINVAL;
 
 		ctx->pos = vbo + off;
 
 		/* Submit the name to the filldir callback. */
-		err = ntfs_filldir(sbi, ni, e, name, ctx);
-		if (err)
-			return err;
+		if (!ntfs_dir_emit(sbi, ni, e, name, ctx)) {
+			/* ctx is full. */
+			return +1;
+		}
 	}
 }
 
@@ -450,7 +482,6 @@
 
 		vbo = (u64)bit << index_bits;
 		if (vbo >= i_size) {
-			ntfs_inode_err(dir, "Looks like your dir is corrupt");
 			err = -EINVAL;
 			goto out;
 		}
@@ -473,9 +504,16 @@
 	__putname(name);
 	put_indx_node(node);
 
-	if (err == -ENOENT) {
+	if (err == 1) {
+		/* 'ctx' is full. */
+		err = 0;
+	} else if (err == -ENOENT) {
 		err = 0;
 		ctx->pos = pos;
+	} else if (err < 0) {
+		if (err == -EINVAL)
+			ntfs_inode_err(dir, "directory corrupted");
+		ctx->pos = eod;
 	}
 
 	return err;
@@ -491,11 +529,9 @@
 	struct INDEX_HDR *hdr;
 	const struct ATTR_FILE_NAME *fname;
 	u32 e_size, off, end;
-	u64 vbo = 0;
 	size_t drs = 0, fles = 0, bit = 0;
-	loff_t i_size = ni->vfs_inode.i_size;
 	struct indx_node *node = NULL;
-	u8 index_bits = ni->dir.index_bits;
+	size_t max_indx = ni->vfs_inode.i_size >> ni->dir.index_bits;
 
 	if (is_empty)
 		*is_empty = true;
@@ -539,7 +575,7 @@
 				fles += 1;
 		}
 
-		if (vbo >= i_size)
+		if (bit >= max_indx)
 			goto out;
 
 		err = indx_used_bit(&ni->dir, ni, &bit);
@@ -549,8 +585,7 @@
 		if (bit == MINUS_ONE_T)
 			goto out;
 
-		vbo = (u64)bit << index_bits;
-		if (vbo >= i_size)
+		if (bit >= max_indx)
 			goto out;
 
 		err = indx_read(&ni->dir, ni, bit << ni->dir.idx2vbn_bits,
@@ -560,7 +595,6 @@
 
 		hdr = &node->index->ihdr;
 		bit += 1;
-		vbo = (u64)bit << ni->dir.idx2vbn_bits;
 	}
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/file.c
@@ -398,10 +398,7 @@
 		}
 
 		if (ni->i_valid < to) {
-			if (!inode_trylock(inode)) {
-				err = -EAGAIN;
-				goto out;
-			}
+			inode_lock(inode);
 			err = ntfs_extend_initialized_size(file, ni,
 							   ni->i_valid, to);
 			inode_unlock(inode);
@@ -488,13 +485,13 @@
 
 	new_valid = ntfs_up_block(sb, min_t(u64, ni->i_valid, new_size));
 
-	ni_lock(ni);
-
 	truncate_setsize(inode, new_size);
 
+	ni_lock(ni);
+
 	down_write(&ni->file.run_lock);
 	err = attr_set_size(ni, ATTR_DATA, NULL, 0, &ni->file.run, new_size,
-			    &new_valid, true, NULL);
+			    &new_valid, ni->mi.sbi->options->prealloc, NULL);
 	up_write(&ni->file.run_lock);
 
 	if (new_valid < ni->i_valid)
@@ -661,7 +658,13 @@
 		/*
 		 * Normal file: Allocate clusters, do not change 'valid' size.
 		 */
-		err = ntfs_set_size(inode, max(end, i_size));
+		loff_t new_size = max(end, i_size);
+
+		err = inode_newsize_ok(inode, new_size);
+		if (err)
+			goto out;
+
+		err = ntfs_set_size(inode, new_size);
 		if (err)
 			goto out;
 
@@ -761,7 +764,7 @@
 		}
 		inode_dio_wait(inode);
 
-		if (attr->ia_size < oldsize)
+		if (attr->ia_size <= oldsize)
 			err = ntfs_truncate(inode, attr->ia_size);
 		else if (attr->ia_size > oldsize)
 			err = ntfs_extend(inode, attr->ia_size, 0, NULL);
@@ -989,7 +992,7 @@
 		frame_vbo = pos & ~(frame_size - 1);
 		index = frame_vbo >> PAGE_SHIFT;
 
-		if (unlikely(iov_iter_fault_in_readable(from, bytes))) {
+		if (unlikely(fault_in_iov_iter_readable(from, bytes))) {
 			err = -EFAULT;
 			goto out;
 		}
@@ -1084,6 +1087,8 @@
 	iocb->ki_pos += written;
 	if (iocb->ki_pos > ni->i_valid)
 		ni->i_valid = iocb->ki_pos;
+	if (iocb->ki_pos > i_size)
+		i_size_write(inode, iocb->ki_pos);
 
 	return written;
 }
@@ -1187,8 +1192,16 @@
 	int err = 0;
 
 	/* If we are last writer on the inode, drop the block reservation. */
-	if (sbi->options->prealloc && ((file->f_mode & FMODE_WRITE) &&
-				      atomic_read(&inode->i_writecount) == 1)) {
+	if (sbi->options->prealloc &&
+	    ((file->f_mode & FMODE_WRITE) &&
+	     atomic_read(&inode->i_writecount) == 1)
+	   /*
+	    * The only file when inode->i_fop = &ntfs_file_operations and
+	    * init_rwsem(&ni->file.run_lock) is not called explicitly is MFT.
+	    *
+	    * Add additional check here.
+	    */
+	    && inode->i_ino != MFT_REC_MFT) {
 		ni_lock(ni);
 		down_write(&ni->file.run_lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/frecord.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/frecord.c
@@ -101,7 +101,9 @@
 {
 	struct rb_node *node;
 
-	if (!ni->vfs_inode.i_nlink && is_rec_inuse(ni->mi.mrec))
+	if (!ni->vfs_inode.i_nlink && ni->mi.mrec &&
+	    is_rec_inuse(ni->mi.mrec) &&
+	    !(ni->mi.sbi->flags & NTFS_FLAGS_LOG_REPLAYING))
 		ni_delete_all(ni);
 
 	al_destroy(ni);
@@ -567,6 +569,12 @@
 		}
 
 		roff = le16_to_cpu(attr->nres.run_off);
+
+		if (roff > le32_to_cpu(attr->size)) {
+			err = -EINVAL;
+			break;
+		}
+
 		err = run_unpack(&run, sbi, ni->mi.rno, svcn, evcn, svcn,
 				 Add2Ptr(attr, roff),
 				 le32_to_cpu(attr->size) - roff);
@@ -744,7 +752,7 @@
 	run_deallocate(sbi, &ni->attr_list.run, true);
 	run_close(&ni->attr_list.run);
 	ni->attr_list.size = 0;
-	kfree(ni->attr_list.le);
+	kvfree(ni->attr_list.le);
 	ni->attr_list.le = NULL;
 	ni->attr_list.dirty = false;
 
@@ -843,6 +851,7 @@
 	if (err)
 		goto out1;
 
+	err = -EINVAL;
 	/* Call mi_remove_attr() in reverse order to keep pointers 'arr_move' valid. */
 	while (to_free > 0) {
 		struct ATTRIB *b = arr_move[--nb];
@@ -851,7 +860,8 @@
 
 		attr = mi_insert_attr(mi, b->type, Add2Ptr(b, name_off),
 				      b->name_len, asize, name_off);
-		WARN_ON(!attr);
+		if (!attr)
+			goto out1;
 
 		mi_get_ref(mi, &le_b[nb]->ref);
 		le_b[nb]->id = attr->id;
@@ -861,17 +871,20 @@
 		attr->id = le_b[nb]->id;
 
 		/* Remove from primary record. */
-		WARN_ON(!mi_remove_attr(NULL, &ni->mi, b));
+		if (!mi_remove_attr(NULL, &ni->mi, b))
+			goto out1;
 
 		if (to_free <= asize)
 			break;
 		to_free -= asize;
-		WARN_ON(!nb);
+		if (!nb)
+			goto out1;
 	}
 
 	attr = mi_insert_attr(&ni->mi, ATTR_LIST, NULL, 0,
 			      lsize + SIZEOF_RESIDENT, SIZEOF_RESIDENT);
-	WARN_ON(!attr);
+	if (!attr)
+		goto out1;
 
 	attr->non_res = 0;
 	attr->flags = 0;
@@ -888,12 +901,13 @@
 	goto out;
 
 out1:
-	kfree(ni->attr_list.le);
+	kvfree(ni->attr_list.le);
 	ni->attr_list.le = NULL;
 	ni->attr_list.size = 0;
+	return err;
 
 out:
-	return err;
+	return 0;
 }
 
 /*
@@ -1441,7 +1455,7 @@
 
 	if (is_ext) {
 		if (flags & ATTR_FLAG_COMPRESSED)
-			attr->nres.c_unit = COMPRESSION_UNIT;
+			attr->nres.c_unit = NTFS_LZNT_CUNIT;
 		attr->nres.total_size = attr->nres.alloc_size;
 	}
 
@@ -1541,6 +1555,9 @@
 		asize = le32_to_cpu(attr->size);
 		roff = le16_to_cpu(attr->nres.run_off);
 
+		if (roff > asize)
+			return -EINVAL;
+
 		/* run==1 means unpack and deallocate. */
 		run_unpack_ex(RUN_DEALLOCATE, sbi, ni->mi.rno, svcn, evcn, svcn,
 			      Add2Ptr(attr, roff), asize - roff);
@@ -1964,10 +1981,8 @@
 
 		vcn += clen;
 
-		if (vbo + bytes >= end) {
+		if (vbo + bytes >= end)
 			bytes = end - vbo;
-			flags |= FIEMAP_EXTENT_LAST;
-		}
 
 		if (vbo + bytes <= valid) {
 			;
@@ -1977,6 +1992,9 @@
 			/* vbo < valid && valid < vbo + bytes */
 			u64 dlen = valid - vbo;
 
+			if (vbo + dlen >= end)
+				flags |= FIEMAP_EXTENT_LAST;
+
 			err = fiemap_fill_next_extent(fieinfo, vbo, lbo, dlen,
 						      flags);
 			if (err < 0)
@@ -1995,6 +2013,9 @@
 			flags |= FIEMAP_EXTENT_UNWRITTEN;
 		}
 
+		if (vbo + bytes >= end)
+			flags |= FIEMAP_EXTENT_LAST;
+
 		err = fiemap_fill_next_extent(fieinfo, vbo, lbo, bytes, flags);
 		if (err < 0)
 			break;
@@ -2081,7 +2102,7 @@
 
 	for (i = 0; i < pages_per_frame; i++) {
 		pg = pages[i];
-		if (i == idx)
+		if (i == idx || !pg)
 			continue;
 		unlock_page(pg);
 		put_page(pg);
@@ -2238,6 +2259,11 @@
 		asize = le32_to_cpu(attr->size);
 		roff = le16_to_cpu(attr->nres.run_off);
 
+		if (roff > asize) {
+			err = -EINVAL;
+			goto out;
+		}
+
 		/*run==1  Means unpack and deallocate. */
 		run_unpack_ex(RUN_DEALLOCATE, sbi, ni->mi.rno, svcn, evcn, svcn,
 			      Add2Ptr(attr, roff), asize - roff);
@@ -3120,6 +3146,12 @@
 		if (!fname || !memcmp(&fname->dup, dup, sizeof(fname->dup)))
 			continue;
 
+		/* Check simple case when parent inode equals current inode. */
+		if (ino_get(&fname->home) == ni->vfs_inode.i_ino) {
+			ntfs_set_state(sbi, NTFS_DIRTY_ERROR);
+			continue;
+		}
+
 		/* ntfs_iget5 may sleep. */
 		dir = ntfs_iget5(sb, &fname->home, NULL);
 		if (IS_ERR(dir)) {
@@ -3171,6 +3203,9 @@
 		return 0;
 	}
 
+	if (!ni->mi.mrec)
+		goto out;
+
 	if (is_rec_inuse(ni->mi.mrec) &&
 	    !(sbi->flags & NTFS_FLAGS_LOG_REPLAYING) && inode->i_nlink) {
 		bool modified = false;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/fslog.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/fslog.c
@@ -465,7 +465,7 @@
 {
 	const struct RESTART_AREA *ra;
 	u16 cl, fl, ul;
-	u32 off, l_size, file_dat_bits, file_size_round;
+	u32 off, l_size, seq_bits;
 	u16 ro = le16_to_cpu(rhdr->ra_off);
 	u32 sys_page = le32_to_cpu(rhdr->sys_page_size);
 
@@ -511,13 +511,15 @@
 	/* Make sure the sequence number bits match the log file size. */
 	l_size = le64_to_cpu(ra->l_size);
 
-	file_dat_bits = sizeof(u64) * 8 - le32_to_cpu(ra->seq_num_bits);
-	file_size_round = 1u << (file_dat_bits + 3);
-	if (file_size_round != l_size &&
-	    (file_size_round < l_size || (file_size_round / 2) > l_size)) {
-		return false;
+	seq_bits = sizeof(u64) * 8 + 3;
+	while (l_size) {
+		l_size >>= 1;
+		seq_bits -= 1;
 	}
 
+	if (seq_bits != ra->seq_num_bits)
+		return false;
+
 	/* The log page data offset and record header length must be quad-aligned. */
 	if (!IS_ALIGNED(le16_to_cpu(ra->data_off), 8) ||
 	    !IS_ALIGNED(le16_to_cpu(ra->rec_hdr_len), 8))
@@ -607,14 +609,29 @@
 	*head = cpu_to_le16(index);
 }
 
+/*
+ * Enumerate restart table.
+ *
+ * @t - table to enumerate.
+ * @c - current enumerated element.
+ *
+ * enumeration starts with @c == NULL
+ * returns next element or NULL
+ */
 static inline void *enum_rstbl(struct RESTART_TABLE *t, void *c)
 {
 	__le32 *e;
 	u32 bprt;
-	u16 rsize = t ? le16_to_cpu(t->size) : 0;
+	u16 rsize;
+
+	if (!t)
+		return NULL;
+
+	rsize = le16_to_cpu(t->size);
 
 	if (!c) {
-		if (!t || !t->total)
+		/* start enumeration. */
+		if (!t->total)
 			return NULL;
 		e = Add2Ptr(t, sizeof(struct RESTART_TABLE));
 	} else {
@@ -722,7 +739,8 @@
 
 	if (!rsize || rsize > bytes ||
 	    rsize + sizeof(struct RESTART_TABLE) > bytes || bytes < ts ||
-	    le16_to_cpu(rt->total) > ne || ff > ts || lf > ts ||
+	    le16_to_cpu(rt->total) > ne ||
+			ff > ts - sizeof(__le32) || lf > ts - sizeof(__le32) ||
 	    (ff && ff < sizeof(struct RESTART_TABLE)) ||
 	    (lf && lf < sizeof(struct RESTART_TABLE))) {
 		return false;
@@ -752,6 +770,9 @@
 			return false;
 
 		off = le32_to_cpu(*(__le32 *)Add2Ptr(rt, off));
+
+		if (off > ts - sizeof(__le32))
+			return false;
 	}
 
 	return true;
@@ -1132,7 +1153,7 @@
 		return -EINVAL;
 
 	if (!*buffer) {
-		to_free = kmalloc(bytes, GFP_NOFS);
+		to_free = kmalloc(log->page_size, GFP_NOFS);
 		if (!to_free)
 			return -ENOMEM;
 		*buffer = to_free;
@@ -1179,13 +1200,9 @@
 static int log_read_rst(struct ntfs_log *log, u32 l_size, bool first,
 			struct restart_info *info)
 {
-	u32 skip, vbo;
-	struct RESTART_HDR *r_page = kmalloc(DefaultLogPageSize, GFP_NOFS);
-
-	if (!r_page)
-		return -ENOMEM;
-
-	memset(info, 0, sizeof(struct restart_info));
+	u32 skip;
+	u64 vbo;
+	struct RESTART_HDR *r_page = NULL;
 
 	/* Determine which restart area we are looking for. */
 	if (first) {
@@ -1199,7 +1216,6 @@
 	/* Loop continuously until we succeed. */
 	for (; vbo < l_size; vbo = 2 * vbo + skip, skip = 0) {
 		bool usa_error;
-		u32 sys_page_size;
 		bool brst, bchk;
 		struct RESTART_AREA *ra;
 
@@ -1253,24 +1269,6 @@
 			goto check_result;
 		}
 
-		/* Read the entire restart area. */
-		sys_page_size = le32_to_cpu(r_page->sys_page_size);
-		if (DefaultLogPageSize != sys_page_size) {
-			kfree(r_page);
-			r_page = kzalloc(sys_page_size, GFP_NOFS);
-			if (!r_page)
-				return -ENOMEM;
-
-			if (read_log_page(log, vbo,
-					  (struct RECORD_PAGE_HDR **)&r_page,
-					  &usa_error)) {
-				/* Ignore any errors. */
-				kfree(r_page);
-				r_page = NULL;
-				continue;
-			}
-		}
-
 		if (is_client_area_valid(r_page, usa_error)) {
 			info->valid_page = true;
 			ra = Add2Ptr(r_page, le16_to_cpu(r_page->ra_off));
@@ -2193,8 +2191,10 @@
 
 			if (!page) {
 				page = kmalloc(log->page_size, GFP_NOFS);
-				if (!page)
-					return -ENOMEM;
+				if (!page) {
+					err = -ENOMEM;
+					goto out;
+				}
 			}
 
 			/*
@@ -2599,7 +2599,7 @@
 	return find_log_rec(log, *lsn, lcb);
 }
 
-static inline bool check_index_header(const struct INDEX_HDR *hdr, size_t bytes)
+bool check_index_header(const struct INDEX_HDR *hdr, size_t bytes)
 {
 	__le16 mask;
 	u32 min_de, de_off, used, total;
@@ -2729,6 +2729,9 @@
 			return false;
 		}
 
+		if (run_off > asize)
+			return false;
+
 		if (run_unpack(NULL, sbi, 0, svcn, evcn, svcn,
 			       Add2Ptr(attr, run_off), asize - run_off) < 0) {
 			return false;
@@ -3011,7 +3014,7 @@
 	if (is_ext) {
 		attr->name_off = SIZEOF_NONRESIDENT_EX_LE;
 		if (is_attr_compressed(attr))
-			attr->nres.c_unit = COMPRESSION_UNIT;
+			attr->nres.c_unit = NTFS_LZNT_CUNIT;
 
 		attr->nres.run_off =
 			cpu_to_le16(SIZEOF_NONRESIDENT_EX + name_size);
@@ -3791,10 +3794,11 @@
 	if (!log)
 		return -ENOMEM;
 
+	memset(&rst_info, 0, sizeof(struct restart_info));
+
 	log->ni = ni;
 	log->l_size = l_size;
 	log->one_page_buf = kmalloc(page_size, GFP_NOFS);
-
 	if (!log->one_page_buf) {
 		err = -ENOMEM;
 		goto out;
@@ -3842,6 +3846,7 @@
 	if (rst_info.vbo)
 		goto check_restart_area;
 
+	memset(&rst_info2, 0, sizeof(struct restart_info));
 	err = log_read_rst(log, l_size, false, &rst_info2);
 
 	/* Determine which restart area to use. */
@@ -3945,6 +3950,9 @@
 		goto out;
 	}
 
+	log->page_mask = log->page_size - 1;
+	log->page_bits = blksize_bits(log->page_size);
+
 	/* If the file size has shrunk then we won't mount it. */
 	if (l_size < le64_to_cpu(ra2->l_size)) {
 		err = -EINVAL;
@@ -4085,8 +4093,10 @@
 		if (client == LFS_NO_CLIENT_LE) {
 			/* Insert "NTFS" client LogFile. */
 			client = ra->client_idx[0];
-			if (client == LFS_NO_CLIENT_LE)
-				return -EINVAL;
+			if (client == LFS_NO_CLIENT_LE) {
+				err = -EINVAL;
+				goto out;
+			}
 
 			t16 = le16_to_cpu(client);
 			cr = ca + t16;
@@ -4273,6 +4283,10 @@
 	rec_len -= t32;
 
 	attr_names = kmemdup(Add2Ptr(lrh, t32), rec_len, GFP_NOFS);
+	if (!attr_names) {
+		err = -ENOMEM;
+		goto out;
+	}
 
 	lcb_put(lcb);
 	lcb = NULL;
@@ -4767,6 +4781,12 @@
 		u16 roff = le16_to_cpu(attr->nres.run_off);
 		CLST svcn = le64_to_cpu(attr->nres.svcn);
 
+		if (roff > t32) {
+			kfree(oa->attr);
+			oa->attr = NULL;
+			goto fake_attr;
+		}
+
 		err = run_unpack(&oa->run0, sbi, inode->i_ino, svcn,
 				 le64_to_cpu(attr->nres.evcn), svcn,
 				 Add2Ptr(attr, roff), t32 - roff);
@@ -5055,7 +5075,7 @@
 		goto add_allocated_vcns;
 
 	vcn = le64_to_cpu(lrh->target_vcn);
-	vcn &= ~(log->clst_per_page - 1);
+	vcn &= ~(u64)(log->clst_per_page - 1);
 
 add_allocated_vcns:
 	for (i = 0, vcn = le64_to_cpu(lrh->target_vcn),
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/fsntfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/fsntfs.c
@@ -154,7 +154,7 @@
 	/* Check errors. */
 	if ((fo & 1) || fo + fn * sizeof(short) > SECTOR_SIZE || !fn-- ||
 	    fn * SECTOR_SIZE > bytes) {
-		return -EINVAL; /* Native chkntfs returns ok! */
+		return -E_NTFS_CORRUPT;
 	}
 
 	/* Get fixup pointer. */
@@ -475,7 +475,7 @@
 	struct ATTRIB *attr;
 	struct wnd_bitmap *wnd = &sbi->mft.bitmap;
 
-	new_mft_total = (wnd->nbits + MFT_INCREASE_CHUNK + 127) & (CLST)~127;
+	new_mft_total = ALIGN(wnd->nbits + NTFS_MFT_INCREASE_STEP, 128);
 	new_mft_bytes = (u64)new_mft_total << sbi->record_bits;
 
 	/* Step 1: Resize $MFT::DATA. */
@@ -493,7 +493,7 @@
 	ni->mi.dirty = true;
 
 	/* Step 2: Resize $MFT::BITMAP. */
-	new_bitmap_bytes = bitmap_size(new_mft_total);
+	new_bitmap_bytes = ntfs3_bitmap_size(new_mft_total);
 
 	err = attr_set_size(ni, ATTR_BITMAP, NULL, 0, &sbi->mft.bitmap.run,
 			    new_bitmap_bytes, &new_bitmap_bytes, true, NULL);
@@ -831,10 +831,15 @@
 {
 	int err;
 	struct super_block *sb = sbi->sb;
-	u32 blocksize = sb->s_blocksize;
+	u32 blocksize;
 	sector_t block1, block2;
 	u32 bytes;
 
+	if (!sb)
+		return -EINVAL;
+
+	blocksize = sb->s_blocksize;
+
 	if (!(sbi->flags & NTFS_FLAGS_MFTMIRR))
 		return 0;
 
@@ -953,18 +958,11 @@
 	if (err)
 		return err;
 
-	mark_inode_dirty(&ni->vfs_inode);
+	mark_inode_dirty_sync(&ni->vfs_inode);
 	/* verify(!ntfs_update_mftmirr()); */
 
-	/*
-	 * If we used wait=1, sync_inode_metadata waits for the io for the
-	 * inode to finish. It hangs when media is removed.
-	 * So wait=0 is sent down to sync_inode_metadata
-	 * and filemap_fdatawrite is used for the data blocks.
-	 */
-	err = sync_inode_metadata(&ni->vfs_inode, 0);
-	if (!err)
-		err = filemap_fdatawrite(ni->vfs_inode.i_mapping);
+	/* write mft record on disk. */
+	err = _ni_write_inode(&ni->vfs_inode, 1);
 
 	return err;
 }
@@ -983,6 +981,30 @@
 	return cpu_to_le32(hash);
 }
 
+/*
+ * simple wrapper for sb_bread_unmovable.
+ */
+struct buffer_head *ntfs_bread(struct super_block *sb, sector_t block)
+{
+	struct ntfs_sb_info *sbi = sb->s_fs_info;
+	struct buffer_head *bh;
+
+	if (unlikely(block >= sbi->volume.blocks)) {
+		/* prevent generic message "attempt to access beyond end of device" */
+		ntfs_err(sb, "try to read out of volume at offset 0x%llx",
+			 (u64)block << sb->s_blocksize_bits);
+		return NULL;
+	}
+
+	bh = sb_bread_unmovable(sb, block);
+	if (bh)
+		return bh;
+
+	ntfs_err(sb, "failed to read volume at offset 0x%llx",
+		 (u64)block << sb->s_blocksize_bits);
+	return NULL;
+}
+
 int ntfs_sb_read(struct super_block *sb, u64 lbo, size_t bytes, void *buffer)
 {
 	struct block_device *bdev = sb->s_bdev;
@@ -1681,6 +1703,7 @@
 
 out:
 	if (err) {
+		make_bad_inode(inode);
 		iput(inode);
 		ni = ERR_PTR(err);
 	}
@@ -1873,9 +1896,12 @@
 		goto out;
 	}
 
-	root_sdh = resident_data(attr);
-	if (root_sdh->type != ATTR_ZERO ||
-	    root_sdh->rule != NTFS_COLLATION_TYPE_SECURITY_HASH) {
+	if(!(root_sdh = resident_data_ex(attr, sizeof(struct INDEX_ROOT))) ||
+	    root_sdh->type != ATTR_ZERO ||
+	    root_sdh->rule != NTFS_COLLATION_TYPE_SECURITY_HASH ||
+	    offsetof(struct INDEX_ROOT, ihdr) +
+			le32_to_cpu(root_sdh->ihdr.used) >
+			le32_to_cpu(attr->res.data_size)) {
 		err = -EINVAL;
 		goto out;
 	}
@@ -1891,9 +1917,12 @@
 		goto out;
 	}
 
-	root_sii = resident_data(attr);
-	if (root_sii->type != ATTR_ZERO ||
-	    root_sii->rule != NTFS_COLLATION_TYPE_UINT) {
+	if(!(root_sii = resident_data_ex(attr, sizeof(struct INDEX_ROOT))) ||
+	    root_sii->type != ATTR_ZERO ||
+	    root_sii->rule != NTFS_COLLATION_TYPE_UINT ||
+	    offsetof(struct INDEX_ROOT, ihdr) +
+			le32_to_cpu(root_sii->ihdr.used) >
+			le32_to_cpu(attr->res.data_size)) {
 		err = -EINVAL;
 		goto out;
 	}
@@ -2450,10 +2479,12 @@
 {
 	CLST end, i;
 	struct wnd_bitmap *wnd = &sbi->used.bitmap;
+	bool dirty = false;
 
 	down_write_nested(&wnd->rw_lock, BITMAP_MUTEX_CLUSTERS);
 	if (!wnd_is_used(wnd, lcn, len)) {
-		ntfs_set_state(sbi, NTFS_DIRTY_ERROR);
+		/* mark volume as dirty out of wnd->rw_lock */
+		dirty = true;
 
 		end = lcn + len;
 		len = 0;
@@ -2485,6 +2516,8 @@
 
 out:
 	up_write(&wnd->rw_lock);
+	if (dirty)
+		ntfs_set_state(sbi, NTFS_DIRTY_ERROR);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/index.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/index.c
@@ -605,11 +605,58 @@
 	return e;
 }
 
+/*
+ * index_hdr_check
+ *
+ * return true if INDEX_HDR is valid
+ */
+static bool index_hdr_check(const struct INDEX_HDR *hdr, u32 bytes)
+{
+	u32 end = le32_to_cpu(hdr->used);
+	u32 tot = le32_to_cpu(hdr->total);
+	u32 off = le32_to_cpu(hdr->de_off);
+
+	if (!IS_ALIGNED(off, 8) || tot > bytes || end > tot ||
+	    size_add(off, sizeof(struct NTFS_DE)) > end) {
+		/* incorrect index buffer. */
+		return false;
+	}
+
+	return true;
+}
+
+/*
+ * index_buf_check
+ *
+ * return true if INDEX_BUFFER seems is valid
+ */
+static bool index_buf_check(const struct INDEX_BUFFER *ib, u32 bytes,
+			    const CLST *vbn)
+{
+	const struct NTFS_RECORD_HEADER *rhdr = &ib->rhdr;
+	u16 fo = le16_to_cpu(rhdr->fix_off);
+	u16 fn = le16_to_cpu(rhdr->fix_num);
+
+	if (bytes <= offsetof(struct INDEX_BUFFER, ihdr) ||
+	    rhdr->sign != NTFS_INDX_SIGNATURE ||
+	    fo < sizeof(struct INDEX_BUFFER)
+	    /* Check index buffer vbn. */
+	    || (vbn && *vbn != le64_to_cpu(ib->vbn)) || (fo % sizeof(short)) ||
+	    fo + fn * sizeof(short) >= bytes ||
+	    fn != ((bytes >> SECTOR_SHIFT) + 1)) {
+		/* incorrect index buffer. */
+		return false;
+	}
+
+	return index_hdr_check(&ib->ihdr,
+			       bytes - offsetof(struct INDEX_BUFFER, ihdr));
+}
+
 void fnd_clear(struct ntfs_fnd *fnd)
 {
 	int i;
 
-	for (i = 0; i < fnd->level; i++) {
+	for (i = fnd->level - 1; i >= 0; i--) {
 		struct indx_node *n = fnd->nodes[i];
 
 		if (!n)
@@ -679,10 +726,17 @@
 	u32 e_size, e_key_len;
 	u32 end = le32_to_cpu(hdr->used);
 	u32 off = le32_to_cpu(hdr->de_off);
+	u32 total = le32_to_cpu(hdr->total);
 	u16 offs[128];
 
+	if (unlikely(!cmp))
+		return NULL;
+
 fill_table:
-	if (off + sizeof(struct NTFS_DE) > end)
+	if (end > total)
+		return NULL;
+
+	if (size_add(off, sizeof(struct NTFS_DE)) > end)
 		return NULL;
 
 	e = Add2Ptr(hdr, off);
@@ -798,6 +852,10 @@
 	u32 off = PtrOffset(hdr, re);
 	int bytes = used - (off + esize);
 
+	/* check INDEX_HDR valid before using INDEX_HDR */
+	if (!check_index_header(hdr, le32_to_cpu(hdr->total)))
+		return NULL;
+
 	if (off >= used || esize < sizeof(struct NTFS_DE) ||
 	    bytes < sizeof(struct NTFS_DE))
 		return NULL;
@@ -820,9 +878,16 @@
 	u32 t32;
 	const struct INDEX_ROOT *root = resident_data(attr);
 
+	t32 = le32_to_cpu(attr->res.data_size);
+	if (t32 <= offsetof(struct INDEX_ROOT, ihdr) ||
+	    !index_hdr_check(&root->ihdr,
+			     t32 - offsetof(struct INDEX_ROOT, ihdr))) {
+		goto out;
+	}
+
 	/* Check root fields. */
 	if (!root->index_block_clst)
-		return -EINVAL;
+		goto out;
 
 	indx->type = type;
 	indx->idx2vbn_bits = __ffs(root->index_block_clst);
@@ -834,19 +899,19 @@
 	if (t32 < sbi->cluster_size) {
 		/* Index record is smaller than a cluster, use 512 blocks. */
 		if (t32 != root->index_block_clst * SECTOR_SIZE)
-			return -EINVAL;
+			goto out;
 
 		/* Check alignment to a cluster. */
 		if ((sbi->cluster_size >> SECTOR_SHIFT) &
 		    (root->index_block_clst - 1)) {
-			return -EINVAL;
+			goto out;
 		}
 
 		indx->vbn2vbo_bits = SECTOR_SHIFT;
 	} else {
 		/* Index record must be a multiple of cluster size. */
 		if (t32 != root->index_block_clst << sbi->cluster_bits)
-			return -EINVAL;
+			goto out;
 
 		indx->vbn2vbo_bits = sbi->cluster_bits;
 	}
@@ -854,7 +919,14 @@
 	init_rwsem(&indx->run_lock);
 
 	indx->cmp = get_cmp_func(root);
-	return indx->cmp ? 0 : -EINVAL;
+	if (!indx->cmp)
+		goto out;
+
+	return 0;
+
+out:
+	ntfs_set_state(sbi, NTFS_DIRTY_DIRTY);
+	return -EINVAL;
 }
 
 static struct indx_node *indx_new(struct ntfs_index *indx,
@@ -907,7 +979,7 @@
 		hdr->used =
 			cpu_to_le32(eo + sizeof(struct NTFS_DE) + sizeof(u64));
 		de_set_vbn_le(e, *sub_vbn);
-		hdr->flags = 1;
+		hdr->flags = NTFS_INDEX_HDR_HAS_SUBNODES;
 	} else {
 		e->size = cpu_to_le16(sizeof(struct NTFS_DE));
 		hdr->used = cpu_to_le32(eo + sizeof(struct NTFS_DE));
@@ -926,6 +998,7 @@
 	struct ATTR_LIST_ENTRY *le = NULL;
 	struct ATTRIB *a;
 	const struct INDEX_NAMES *in = &s_index_names[indx->type];
+	struct INDEX_ROOT *root = NULL;
 
 	a = ni_find_attr(ni, NULL, &le, ATTR_ROOT, in->name, in->name_len, NULL,
 			 mi);
@@ -935,7 +1008,15 @@
 	if (attr)
 		*attr = a;
 
-	return resident_data_ex(a, sizeof(struct INDEX_ROOT));
+	root = resident_data_ex(a, sizeof(struct INDEX_ROOT));
+
+	/* length check */
+	if (root && offsetof(struct INDEX_ROOT, ihdr) + le32_to_cpu(root->ihdr.used) >
+			le32_to_cpu(a->res.data_size)) {
+		return NULL;
+	}
+
+	return root;
 }
 
 static int indx_write(struct ntfs_index *indx, struct ntfs_inode *ni,
@@ -1012,15 +1093,35 @@
 		goto out;
 
 ok:
+	if (!index_buf_check(ib, bytes, &vbn)) {
+		ntfs_inode_err(&ni->vfs_inode, "directory corrupted");
+		ntfs_set_state(ni->mi.sbi, NTFS_DIRTY_ERROR);
+		err = -EINVAL;
+		goto out;
+	}
+
 	if (err == -E_NTFS_FIXUP) {
 		ntfs_write_bh(ni->mi.sbi, &ib->rhdr, &in->nb, 0);
 		err = 0;
 	}
 
+	/* check for index header length */
+	if (offsetof(struct INDEX_BUFFER, ihdr) + le32_to_cpu(ib->ihdr.used) >
+	    bytes) {
+		err = -EINVAL;
+		goto out;
+	}
+
 	in->index = ib;
 	*node = in;
 
 out:
+	if (err == -E_NTFS_CORRUPT) {
+		ntfs_inode_err(&ni->vfs_inode, "directory corrupted");
+		ntfs_set_state(ni->mi.sbi, NTFS_DIRTY_ERROR);
+		err = -EINVAL;
+	}
+
 	if (ib != in->index)
 		kfree(ib);
 
@@ -1360,8 +1461,8 @@
 
 	alloc->nres.valid_size = alloc->nres.data_size = cpu_to_le64(data_size);
 
-	err = ni_insert_resident(ni, bitmap_size(1), ATTR_BITMAP, in->name,
-				 in->name_len, &bitmap, NULL, NULL);
+	err = ni_insert_resident(ni, ntfs3_bitmap_size(1), ATTR_BITMAP,
+				 in->name, in->name_len, &bitmap, NULL, NULL);
 	if (err)
 		goto out2;
 
@@ -1422,8 +1523,9 @@
 	if (bmp) {
 		/* Increase bitmap. */
 		err = attr_set_size(ni, ATTR_BITMAP, in->name, in->name_len,
-				    &indx->bitmap_run, bitmap_size(bit + 1),
-				    NULL, true, NULL);
+				    &indx->bitmap_run,
+				    ntfs3_bitmap_size(bit + 1), NULL, true,
+				    NULL);
 		if (err)
 			goto out1;
 	}
@@ -1437,6 +1539,11 @@
 		goto out1;
 	}
 
+	if (data_size <= le64_to_cpu(alloc->nres.data_size)) {
+		/* Reuse index. */
+		goto out;
+	}
+
 	/* Increase allocation. */
 	err = attr_set_size(ni, ATTR_ALLOC, in->name, in->name_len,
 			    &indx->alloc_run, data_size, &data_size, true,
@@ -1447,6 +1554,7 @@
 		goto out1;
 	}
 
+out:
 	*vbn = bit << indx->idx2vbn_bits;
 
 	return 0;
@@ -1577,7 +1685,7 @@
 	e->size = cpu_to_le16(sizeof(struct NTFS_DE) + sizeof(u64));
 	e->flags = NTFS_IE_HAS_SUBNODES | NTFS_IE_LAST;
 
-	hdr->flags = 1;
+	hdr->flags = NTFS_INDEX_HDR_HAS_SUBNODES;
 	hdr->used = hdr->total =
 		cpu_to_le32(new_root_size - offsetof(struct INDEX_ROOT, ihdr));
 
@@ -1600,9 +1708,9 @@
 
 	if (err) {
 		/* Restore root. */
-		if (mi_resize_attr(mi, attr, -ds_root))
+		if (mi_resize_attr(mi, attr, -ds_root)) {
 			memcpy(attr, a_root, asize);
-		else {
+		} else {
 			/* Bug? */
 			ntfs_set_state(sbi, NTFS_DIRTY_ERROR);
 		}
@@ -1980,7 +2088,7 @@
 	if (err)
 		return err;
 
-	bpb = bitmap_size(bit);
+	bpb = ntfs3_bitmap_size(bit);
 	if (bpb * 8 == nbits)
 		return 0;
 
@@ -1994,7 +2102,7 @@
 			      const struct NTFS_DE *e, bool trim)
 {
 	int err;
-	struct indx_node *n;
+	struct indx_node *n = NULL;
 	struct INDEX_HDR *hdr;
 	CLST vbn = de_get_vbn(e);
 	size_t i;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/inode.c
@@ -37,7 +37,7 @@
 	bool is_dir;
 	unsigned long ino = inode->i_ino;
 	u32 rp_fa = 0, asize, t32;
-	u16 roff, rsize, names = 0;
+	u16 roff, rsize, names = 0, links = 0;
 	const struct ATTR_FILE_NAME *fname = NULL;
 	const struct INDEX_ROOT *root;
 	struct REPARSE_DATA_BUFFER rp; // 0x18 bytes
@@ -81,7 +81,7 @@
 			 le16_to_cpu(ref->seq), le16_to_cpu(rec->seq));
 		goto out;
 	} else if (!is_rec_inuse(rec)) {
-		err = -EINVAL;
+		err = -ESTALE;
 		ntfs_err(sb, "Inode r=%x is not in use!", (u32)ino);
 		goto out;
 	}
@@ -92,12 +92,20 @@
 		goto out;
 	}
 
-	if (!is_rec_base(rec))
-		goto Ok;
+	if (!is_rec_base(rec)) {
+		err = -EINVAL;
+		goto out;
+	}
 
 	/* Record should contain $I30 root. */
 	is_dir = rec->flags & RECORD_FLAG_DIR;
 
+	/* MFT_REC_MFT is not a dir */
+	if (is_dir && ino == MFT_REC_MFT) {
+		err = -EINVAL;
+		goto out;
+	}
+
 	inode->i_generation = le16_to_cpu(rec->seq);
 
 	/* Enumerate all struct Attributes MFT. */
@@ -129,6 +137,16 @@
 	rsize = attr->non_res ? 0 : le32_to_cpu(attr->res.data_size);
 	asize = le32_to_cpu(attr->size);
 
+	if (le16_to_cpu(attr->name_off) + attr->name_len > asize)
+		goto out;
+
+	if (attr->non_res) {
+		t64 = le64_to_cpu(attr->nres.alloc_size);
+		if (le64_to_cpu(attr->nres.data_size) > t64 ||
+		    le64_to_cpu(attr->nres.valid_size) > t64)
+			goto out;
+	}
+
 	switch (attr->type) {
 	case ATTR_STD:
 		if (attr->non_res ||
@@ -172,11 +190,12 @@
 		    rsize < SIZEOF_ATTRIBUTE_FILENAME)
 			goto out;
 
+		names += 1;
 		fname = Add2Ptr(attr, roff);
 		if (fname->type == FILE_NAME_DOS)
 			goto next_attr;
 
-		names += 1;
+		links += 1;
 		if (name && name->len == fname->name_len &&
 		    !ntfs_cmp_names_cpu(name, (struct le_str *)&fname->name_len,
 					NULL, false))
@@ -247,7 +266,6 @@
 			goto out;
 
 		root = Add2Ptr(attr, roff);
-		is_root = true;
 
 		if (attr->name_len != ARRAY_SIZE(I30_NAME) ||
 		    memcmp(attr_name(attr), I30_NAME, sizeof(I30_NAME)))
@@ -260,6 +278,7 @@
 		if (!is_dir)
 			goto next_attr;
 
+		is_root = true;
 		ni->ni_flags |= NI_FLAG_DIR;
 
 		err = indx_init(&ni->dir, sbi, attr, INDEX_MUTEX_I30);
@@ -364,7 +383,13 @@
 attr_unpack_run:
 	roff = le16_to_cpu(attr->nres.run_off);
 
+	if (roff > asize) {
+		err = -EINVAL;
+		goto out;
+	}
+
 	t64 = le64_to_cpu(attr->nres.svcn);
+
 	err = run_unpack_ex(run, sbi, ino, t64, le64_to_cpu(attr->nres.evcn),
 			    t64, Add2Ptr(attr, roff), asize - roff);
 	if (err < 0)
@@ -378,7 +403,6 @@
 		goto out;
 
 	if (!is_match && name) {
-		/* Reuse rec as buffer for ascii name. */
 		err = -ENOENT;
 		goto out;
 	}
@@ -393,11 +417,12 @@
 
 	if (names != le16_to_cpu(rec->hard_links)) {
 		/* Correct minor error on the fly. Do not mark inode as dirty. */
+		ntfs_inode_warn(inode, "Correct links count -> %u.", names);
 		rec->hard_links = cpu_to_le16(names);
 		ni->mi.dirty = true;
 	}
 
-	set_nlink(inode, names);
+	set_nlink(inode, links);
 
 	if (S_ISDIR(mode)) {
 		ni->std_fa |= FILE_ATTRIBUTE_DIRECTORY;
@@ -430,6 +455,7 @@
 	} else if (fname && fname->home.low == cpu_to_le32(MFT_REC_EXTEND) &&
 		   fname->home.seq == cpu_to_le16(MFT_REC_EXTEND)) {
 		/* Records in $Extend are not a files or general directories. */
+		inode->i_op = &ntfs_file_inode_operations;
 	} else {
 		err = -EINVAL;
 		goto out;
@@ -449,7 +475,6 @@
 		inode->i_flags |= S_NOSEC;
 	}
 
-Ok:
 	if (ino == MFT_REC_MFT && !sb->s_root)
 		sbi->mft.ni = NULL;
 
@@ -503,6 +528,9 @@
 		make_bad_inode(inode);
 	}
 
+	if (IS_ERR(inode) && name)
+		ntfs_set_state(sb->s_fs_info, NTFS_DIRTY_ERROR);
+
 	return inode;
 }
 
@@ -757,6 +785,7 @@
 	loff_t vbo = iocb->ki_pos;
 	loff_t end;
 	int wr = iov_iter_rw(iter) & WRITE;
+	size_t iter_count = iov_iter_count(iter);
 	loff_t valid;
 	ssize_t ret;
 
@@ -770,10 +799,13 @@
 				 wr ? ntfs_get_block_direct_IO_W
 				    : ntfs_get_block_direct_IO_R);
 
-	if (ret <= 0)
+	if (ret > 0)
+		end = vbo + ret;
+	else if (wr && ret == -EIOCBQUEUED)
+		end = vbo + iter_count;
+	else
 		goto out;
 
-	end = vbo + ret;
 	valid = ni->i_valid;
 	if (wr) {
 		if (end > valid && !S_ISBLK(inode->i_mode)) {
@@ -1433,7 +1465,7 @@
 			attr->size = cpu_to_le32(SIZEOF_NONRESIDENT_EX + 8);
 			attr->name_off = SIZEOF_NONRESIDENT_EX_LE;
 			attr->flags = ATTR_FLAG_COMPRESSED;
-			attr->nres.c_unit = COMPRESSION_UNIT;
+			attr->nres.c_unit = NTFS_LZNT_CUNIT;
 			asize = SIZEOF_NONRESIDENT_EX + 8;
 		} else {
 			attr->size = cpu_to_le32(SIZEOF_NONRESIDENT + 8);
@@ -1620,10 +1652,8 @@
 		ntfs_remove_reparse(sbi, IO_REPARSE_TAG_SYMLINK, &new_de->ref);
 
 out5:
-	if (S_ISDIR(mode) || run_is_empty(&ni->file.run))
-		goto out4;
-
-	run_deallocate(sbi, &ni->file.run, false);
+	if (!S_ISDIR(mode))
+		run_deallocate(sbi, &ni->file.run, false);
 
 out4:
 	clear_rec_inuse(rec);
@@ -1937,8 +1967,6 @@
 	.setattr	= ntfs3_setattr,
 	.listxattr	= ntfs_listxattr,
 	.permission	= ntfs_permission,
-	.get_acl	= ntfs_get_acl,
-	.set_acl	= ntfs_set_acl,
 };
 
 const struct address_space_operations ntfs_aops = {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/lznt.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/lznt.c
@@ -236,6 +236,9 @@
 
 	/* Do decompression until pointers are inside range. */
 	while (up < unc_end && cmpr < cmpr_end) {
+		// return err if more than LZNT_CHUNK_SIZE bytes are written
+		if (up - unc > LZNT_CHUNK_SIZE)
+			return -EINVAL;
 		/* Correct index */
 		while (unc + s_max_off[index] < up)
 			index += 1;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/namei.c
@@ -79,13 +79,23 @@
 		if (err < 0)
 			inode = ERR_PTR(err);
 		else {
-			ni_lock(ni);
+			ni_lock_dir(ni);
 			inode = dir_search_u(dir, uni, NULL);
 			ni_unlock(ni);
 		}
 		__putname(uni);
 	}
 
+	/*
+	 * Check for a null pointer
+	 * If the MFT record of ntfs inode is not a base record, inode->i_op can be NULL.
+	 * This causes null pointer dereference in d_splice_alias().
+	 */
+	if (!IS_ERR_OR_NULL(inode) && !inode->i_op) {
+		iput(inode);
+		inode = ERR_PTR(-EINVAL);
+	}
+
 	return d_splice_alias(inode, dentry);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/ntfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/ntfs.h
@@ -59,7 +59,7 @@
 struct cpu_str {
 	u8 len;
 	u8 unused;
-	u16 name[10];
+	u16 name[];
 };
 
 struct le_str {
@@ -82,10 +82,6 @@
 #define RESIDENT_LCN   ((CLST)-2)
 #define COMPRESSED_LCN ((CLST)-3)
 
-#define COMPRESSION_UNIT     4
-#define COMPRESS_MAX_CLUSTER 0x1000
-#define MFT_INCREASE_CHUNK   1024
-
 enum RECORD_NUM {
 	MFT_REC_MFT		= 0,
 	MFT_REC_MIRR		= 1,
@@ -436,9 +432,6 @@
 	return attr->non_res ? le64_to_cpu(attr->nres.svcn) : 0;
 }
 
-/* The size of resident attribute by its resident size. */
-#define BYTES_PER_RESIDENT(b) (0x18 + (b))
-
 static_assert(sizeof(struct ATTRIB) == 0x48);
 static_assert(sizeof(((struct ATTRIB *)NULL)->res) == 0x08);
 static_assert(sizeof(((struct ATTRIB *)NULL)->nres) == 0x38);
@@ -520,12 +513,10 @@
 	__le64 vcn;		// 0x08: Starting VCN of this attribute.
 	struct MFT_REF ref;	// 0x10: MFT record number with attribute.
 	__le16 id;		// 0x18: struct ATTRIB ID.
-	__le16 name[3];		// 0x1A: Just to align. To get real name can use bNameOffset.
+	__le16 name[];		// 0x1A: Just to align. To get real name can use name_off.
 
 }; // sizeof(0x20)
 
-static_assert(sizeof(struct ATTR_LIST_ENTRY) == 0x20);
-
 static inline u32 le_size(u8 name_len)
 {
 	return ALIGN(offsetof(struct ATTR_LIST_ENTRY, name) +
@@ -695,14 +686,15 @@
 	      offsetof(struct ATTR_FILE_NAME, name) + \
 	      NTFS_NAME_LEN * sizeof(short), 8)
 
+#define NTFS_INDEX_HDR_HAS_SUBNODES cpu_to_le32(1)
+
 struct INDEX_HDR {
 	__le32 de_off;	// 0x00: The offset from the start of this structure
 			// to the first NTFS_DE.
 	__le32 used;	// 0x04: The size of this structure plus all
 			// entries (quad-word aligned).
 	__le32 total;	// 0x08: The allocated size of for this structure plus all entries.
-	u8 flags;	// 0x0C: 0x00 = Small directory, 0x01 = Large directory.
-	u8 res[3];
+	__le32 flags;	// 0x0C: 0x00 = Small directory, 0x01 = Large directory.
 
 	//
 	// de_off + used <= total
@@ -749,7 +741,7 @@
 
 static inline bool hdr_has_subnode(const struct INDEX_HDR *hdr)
 {
-	return hdr->flags & 1;
+	return hdr->flags & NTFS_INDEX_HDR_HAS_SUBNODES;
 }
 
 struct INDEX_BUFFER {
@@ -769,7 +761,7 @@
 
 static inline bool ib_is_leaf(const struct INDEX_BUFFER *ib)
 {
-	return !(ib->ihdr.flags & 1);
+	return !(ib->ihdr.flags & NTFS_INDEX_HDR_HAS_SUBNODES);
 }
 
 /* Index root structure ( 0x90 ). */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/ntfs_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/ntfs_fs.h
@@ -54,6 +54,8 @@
 #define E_NTFS_NONRESIDENT		556
 /* NTFS specific error code about punch hole. */
 #define E_NTFS_NOTALIGNED		557
+/* NTFS specific error code when on-disk struct is corrupted. */
+#define E_NTFS_CORRUPT			558
 
 
 /* sbi->flags */
@@ -196,6 +198,8 @@
 
 /* Minimum MFT zone. */
 #define NTFS_MIN_MFT_ZONE 100
+/* Step to increase the MFT. */
+#define NTFS_MFT_INCREASE_STEP 1024
 
 /* Ntfs file system in-core superblock data. */
 struct ntfs_sb_info {
@@ -324,7 +328,7 @@
 
 /* Nested class for ntfs_inode::ni_lock. */
 enum ntfs_inode_mutex_lock_class {
-	NTFS_INODE_MUTEX_DIRTY,
+	NTFS_INODE_MUTEX_DIRTY = 1,
 	NTFS_INODE_MUTEX_SECURITY,
 	NTFS_INODE_MUTEX_OBJID,
 	NTFS_INODE_MUTEX_REPARSE,
@@ -466,7 +470,7 @@
 int al_update(struct ntfs_inode *ni, int sync);
 static inline size_t al_aligned(size_t size)
 {
-	return (size + 1023) & ~(size_t)1023;
+	return size_add(size, 1023) & ~(size_t)1023;
 }
 
 /* Globals from bitfunc.c */
@@ -575,9 +579,11 @@
 bool ni_is_dirty(struct inode *inode);
 
 /* Globals from fslog.c */
+bool check_index_header(const struct INDEX_HDR *hdr, size_t bytes);
 int log_replay(struct ntfs_inode *ni, bool *initialized);
 
 /* Globals from fsntfs.c */
+struct buffer_head *ntfs_bread(struct super_block *sb, sector_t block);
 bool ntfs_fix_pre_write(struct NTFS_RECORD_HEADER *rhdr, size_t bytes);
 int ntfs_fix_post_read(struct NTFS_RECORD_HEADER *rhdr, size_t bytes,
 		       bool simple);
@@ -788,12 +794,12 @@
 	     u32 run_buf_size, CLST *packed_vcns);
 int run_unpack(struct runs_tree *run, struct ntfs_sb_info *sbi, CLST ino,
 	       CLST svcn, CLST evcn, CLST vcn, const u8 *run_buf,
-	       u32 run_buf_size);
+	       int run_buf_size);
 
 #ifdef NTFS3_CHECK_FREE_CLST
 int run_unpack_ex(struct runs_tree *run, struct ntfs_sb_info *sbi, CLST ino,
 		  CLST svcn, CLST evcn, CLST vcn, const u8 *run_buf,
-		  u32 run_buf_size);
+		  int run_buf_size);
 #else
 #define run_unpack_ex run_unpack
 #endif
@@ -944,9 +950,9 @@
 }
 
 /* NTFS uses quad aligned bitmaps. */
-static inline size_t bitmap_size(size_t bits)
+static inline size_t ntfs3_bitmap_size(size_t bits)
 {
-	return ALIGN((bits + 7) >> 3, 8);
+	return BITS_TO_U64(bits) * sizeof(u64);
 }
 
 #define _100ns2seconds 10000000
@@ -1008,19 +1014,6 @@
 	return (size + sb->s_blocksize - 1) >> sb->s_blocksize_bits;
 }
 
-static inline struct buffer_head *ntfs_bread(struct super_block *sb,
-					     sector_t block)
-{
-	struct buffer_head *bh = sb_bread(sb, block);
-
-	if (bh)
-		return bh;
-
-	ntfs_err(sb, "failed to read volume at offset 0x%llx",
-		 (u64)block << sb->s_blocksize_bits);
-	return NULL;
-}
-
 static inline struct ntfs_inode *ntfs_i(struct inode *inode)
 {
 	return container_of(inode, struct ntfs_inode, vfs_inode);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/record.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/record.c
@@ -124,7 +124,7 @@
 	struct rw_semaphore *rw_lock = NULL;
 
 	if (is_mounted(sbi)) {
-		if (!is_mft) {
+		if (!is_mft && mft_ni) {
 			rw_lock = &mft_ni->file.run_lock;
 			down_read(rw_lock);
 		}
@@ -148,7 +148,7 @@
 		ni_lock(mft_ni);
 		down_write(rw_lock);
 	}
-	err = attr_load_runs_vcn(mft_ni, ATTR_DATA, NULL, 0, &mft_ni->file.run,
+	err = attr_load_runs_vcn(mft_ni, ATTR_DATA, NULL, 0, run,
 				 vbo >> sbi->cluster_bits);
 	if (rw_lock) {
 		up_write(rw_lock);
@@ -180,6 +180,12 @@
 	return 0;
 
 out:
+	if (err == -E_NTFS_CORRUPT) {
+		ntfs_err(sbi->sb, "mft corrupted");
+		ntfs_set_state(sbi, NTFS_DIRTY_ERROR);
+		err = -EINVAL;
+	}
+
 	return err;
 }
 
@@ -209,24 +215,20 @@
 
 		attr = Add2Ptr(rec, off);
 	} else {
-		/* Check if input attr inside record. */
+		/*
+		 * We don't need to check previous attr here. There is
+		 * a bounds checking in the previous round.
+		 */
 		off = PtrOffset(rec, attr);
-		if (off >= used)
-			return NULL;
 
 		asize = le32_to_cpu(attr->size);
-		if (asize < SIZEOF_RESIDENT) {
-			/* Impossible 'cause we should not return such attribute. */
-			return NULL;
-		}
 
 		attr = Add2Ptr(attr, asize);
 		off += asize;
 	}
 
-	asize = le32_to_cpu(attr->size);
-
 	/* Can we use the first field (attr->type). */
+	/* NOTE: this code also checks attr->size availability. */
 	if (off + 8 > used) {
 		static_assert(ALIGN(sizeof(enum ATTR_TYPE), 8) == 8);
 		return NULL;
@@ -242,8 +244,10 @@
 	if ((t32 & 0xf) || (t32 > 0x100))
 		return NULL;
 
-	/* Check boundary. */
-	if (off + asize > used)
+	asize = le32_to_cpu(attr->size);
+
+	/* Check overflow and boundary. */
+	if (off + asize < off || off + asize > used)
 		return NULL;
 
 	/* Check size of attribute. */
@@ -260,10 +264,19 @@
 		if (t16 + t32 > asize)
 			return NULL;
 
+		if (attr->name_len &&
+		    le16_to_cpu(attr->name_off) + sizeof(short) * attr->name_len > t16) {
+			return NULL;
+		}
+
 		return attr;
 	}
 
 	/* Check some nonresident fields. */
+	/* Can we use memory including attr->nres.valid_size? */
+	if (asize < SIZEOF_NONRESIDENT)
+		return NULL;
+
 	if (attr->name_len &&
 	    le16_to_cpu(attr->name_off) + sizeof(short) * attr->name_len >
 		    le16_to_cpu(attr->nres.run_off)) {
@@ -271,12 +284,9 @@
 	}
 
 	if (attr->nres.svcn || !is_attr_ext(attr)) {
-		if (asize + 8 < SIZEOF_NONRESIDENT)
-			return NULL;
-
 		if (attr->nres.c_unit)
 			return NULL;
-	} else if (asize + 8 < SIZEOF_NONRESIDENT_EX)
+	} else if (asize < SIZEOF_NONRESIDENT_EX)
 		return NULL;
 
 	return attr;
@@ -497,9 +507,14 @@
 	if (aoff + asize > used)
 		return false;
 
-	if (ni && is_attr_indexed(attr)) {
-		le16_add_cpu(&ni->mi.mrec->hard_links, -1);
-		ni->mi.dirty = true;
+	if (ni && is_attr_indexed(attr) && attr->type == ATTR_NAME) {
+		u16 links = le16_to_cpu(ni->mi.mrec->hard_links);
+		if (!links) {
+			/* minor error. Not critical. */
+		} else {
+			ni->mi.mrec->hard_links = cpu_to_le16(links - 1);
+			ni->mi.dirty = true;
+		}
 	}
 
 	used -= asize;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/run.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/run.c
@@ -872,12 +872,15 @@
  */
 int run_unpack(struct runs_tree *run, struct ntfs_sb_info *sbi, CLST ino,
 	       CLST svcn, CLST evcn, CLST vcn, const u8 *run_buf,
-	       u32 run_buf_size)
+	       int run_buf_size)
 {
 	u64 prev_lcn, vcn64, lcn, next_vcn;
 	const u8 *run_last, *run_0;
 	bool is_mft = ino == MFT_REC_MFT;
 
+	if (run_buf_size < 0)
+		return -EINVAL;
+
 	/* Check for empty. */
 	if (evcn + 1 == svcn)
 		return 0;
@@ -999,7 +1002,7 @@
  */
 int run_unpack_ex(struct runs_tree *run, struct ntfs_sb_info *sbi, CLST ino,
 		  CLST svcn, CLST evcn, CLST vcn, const u8 *run_buf,
-		  u32 run_buf_size)
+		  int run_buf_size)
 {
 	int ret, err;
 	CLST next_vcn, lcn, len;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/super.c
@@ -30,6 +30,7 @@
 #include <linux/fs_context.h>
 #include <linux/fs_parser.h>
 #include <linux/log2.h>
+#include <linux/minmax.h>
 #include <linux/module.h>
 #include <linux/nls.h>
 #include <linux/seq_file.h>
@@ -390,7 +391,7 @@
 		return -EINVAL;
 	}
 
-	memcpy(sbi->options, new_opts, sizeof(*new_opts));
+	swap(sbi->options, fc->fs_private);
 
 	return 0;
 }
@@ -440,7 +441,7 @@
 {
 	kfree(sbi->new_rec);
 	kvfree(ntfs_put_shared(sbi->upcase));
-	kfree(sbi->def_table);
+	kvfree(sbi->def_table);
 
 	wnd_close(&sbi->mft.bitmap);
 	wnd_close(&sbi->used.bitmap);
@@ -668,9 +669,11 @@
 
 static u32 true_sectors_per_clst(const struct NTFS_BOOT *boot)
 {
-	return boot->sectors_per_clusters <= 0x80
-		       ? boot->sectors_per_clusters
-		       : (1u << (0 - boot->sectors_per_clusters));
+	if (boot->sectors_per_clusters <= 0x80)
+		return boot->sectors_per_clusters;
+	if (boot->sectors_per_clusters >= 0xf4) /* limit shift to 2MB max */
+		return 1U << -(s8)boot->sectors_per_clusters;
+	return -EINVAL;
 }
 
 /*
@@ -713,6 +716,8 @@
 
 	/* cluster size: 512, 1K, 2K, 4K, ... 2M */
 	sct_per_clst = true_sectors_per_clst(boot);
+	if ((int)sct_per_clst < 0)
+		goto out;
 	if (!is_power_of_2(sct_per_clst))
 		goto out;
 
@@ -784,7 +789,7 @@
 						 : (u32)boot->record_size
 							   << sbi->cluster_bits;
 
-	if (record_size > MAXIMUM_BYTES_PER_MFT)
+	if (record_size > MAXIMUM_BYTES_PER_MFT || record_size < SECTOR_SIZE)
 		goto out;
 
 	sbi->record_bits = blksize_bits(record_size);
@@ -897,6 +902,8 @@
 	ref.high = 0;
 
 	sbi->sb = sb;
+	sbi->options = fc->fs_private;
+	fc->fs_private = NULL;
 	sb->s_flags |= SB_NODIRATIME;
 	sb->s_magic = 0x7366746e; // "ntfs"
 	sb->s_op = &ntfs_sops;
@@ -1096,7 +1103,7 @@
 
 	/* Check bitmap boundary. */
 	tt = sbi->used.bitmap.nbits;
-	if (inode->i_size < bitmap_size(tt)) {
+	if (inode->i_size < ntfs3_bitmap_size(tt)) {
 		err = -EINVAL;
 		goto put_inode_out;
 	}
@@ -1129,7 +1136,7 @@
 		goto put_inode_out;
 	}
 	bytes = inode->i_size;
-	sbi->def_table = t = kmalloc(bytes, GFP_NOFS);
+	sbi->def_table = t = kvmalloc(bytes, GFP_KERNEL);
 	if (!t) {
 		err = -ENOMEM;
 		goto put_inode_out;
@@ -1248,9 +1255,9 @@
 	ref.low = cpu_to_le32(MFT_REC_ROOT);
 	ref.seq = cpu_to_le16(MFT_REC_ROOT);
 	inode = ntfs_iget5(sb, &ref, &NAME_ROOT);
-	if (IS_ERR(inode)) {
+	if (IS_ERR(inode) || !inode->i_op) {
 		ntfs_err(sb, "Failed to load root.");
-		err = PTR_ERR(inode);
+		err = IS_ERR(inode) ? PTR_ERR(inode) : -EINVAL;
 		goto out;
 	}
 
@@ -1260,8 +1267,6 @@
 		goto put_inode_out;
 	}
 
-	fc->fs_private = NULL;
-
 	return 0;
 
 put_inode_out:
@@ -1271,6 +1276,7 @@
 	 * Free resources here.
 	 * ntfs_fs_free will be called with fc->s_fs_info = NULL
 	 */
+	put_mount_options(sbi->options);
 	put_ntfs(sbi);
 	sb->s_fs_info = NULL;
 
@@ -1414,7 +1420,6 @@
 	mutex_init(&sbi->compress.mtx_lzx);
 #endif
 
-	sbi->options = opts;
 	fc->s_fs_info = sbi;
 ok:
 	fc->fs_private = opts;
@@ -1443,8 +1448,6 @@
 {
 	int err;
 
-	pr_info("ntfs3: Max link count %u\n", NTFS_LINK_MAX);
-
 	if (IS_ENABLED(CONFIG_NTFS3_FS_POSIX_ACL))
 		pr_info("ntfs3: Enabled Linux POSIX ACLs support\n");
 	if (IS_ENABLED(CONFIG_NTFS3_64BIT_CLUSTER))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ntfs3/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ntfs3/xattr.c
@@ -42,28 +42,26 @@
  * Assume there is at least one xattr in the list.
  */
 static inline bool find_ea(const struct EA_FULL *ea_all, u32 bytes,
-			   const char *name, u8 name_len, u32 *off)
+			   const char *name, u8 name_len, u32 *off, u32 *ea_sz)
 {
-	*off = 0;
+	u32 ea_size;
 
-	if (!ea_all || !bytes)
+	*off = 0;
+	if (!ea_all)
 		return false;
 
-	for (;;) {
+	for (; *off < bytes; *off += ea_size) {
 		const struct EA_FULL *ea = Add2Ptr(ea_all, *off);
-		u32 next_off = *off + unpacked_ea_size(ea);
-
-		if (next_off > bytes)
-			return false;
-
+		ea_size = unpacked_ea_size(ea);
 		if (ea->name_len == name_len &&
-		    !memcmp(ea->name, name, name_len))
+		    !memcmp(ea->name, name, name_len)) {
+			if (ea_sz)
+				*ea_sz = ea_size;
 			return true;
-
-		*off = next_off;
-		if (next_off >= bytes)
-			return false;
+		}
 	}
+
+	return false;
 }
 
 /*
@@ -74,12 +72,12 @@
 static int ntfs_read_ea(struct ntfs_inode *ni, struct EA_FULL **ea,
 			size_t add_bytes, const struct EA_INFO **info)
 {
-	int err;
+	int err = -EINVAL;
 	struct ntfs_sb_info *sbi = ni->mi.sbi;
 	struct ATTR_LIST_ENTRY *le = NULL;
 	struct ATTRIB *attr_info, *attr_ea;
 	void *ea_p;
-	u32 size;
+	u32 size, off, ea_size;
 
 	static_assert(le32_to_cpu(ATTR_EA_INFO) < le32_to_cpu(ATTR_EA));
 
@@ -96,52 +94,87 @@
 
 	*info = resident_data_ex(attr_info, sizeof(struct EA_INFO));
 	if (!*info)
-		return -EINVAL;
+		goto out;
 
 	/* Check Ea limit. */
 	size = le32_to_cpu((*info)->size);
-	if (size > sbi->ea_max_size)
-		return -EFBIG;
+	if (size > sbi->ea_max_size) {
+		err = -EFBIG;
+		goto out;
+	}
 
-	if (attr_size(attr_ea) > sbi->ea_max_size)
-		return -EFBIG;
+	if (attr_size(attr_ea) > sbi->ea_max_size) {
+		err = -EFBIG;
+		goto out;
+	}
+
+	if (!size) {
+		/* EA info persists, but xattr is empty. Looks like EA problem. */
+		goto out;
+	}
 
 	/* Allocate memory for packed Ea. */
-	ea_p = kmalloc(size + add_bytes, GFP_NOFS);
+	ea_p = kmalloc(size_add(size, add_bytes), GFP_NOFS);
 	if (!ea_p)
 		return -ENOMEM;
 
-	if (!size) {
-		;
-	} else if (attr_ea->non_res) {
+	if (attr_ea->non_res) {
 		struct runs_tree run;
 
 		run_init(&run);
 
-		err = attr_load_runs(attr_ea, ni, &run, NULL);
+		err = attr_load_runs_range(ni, ATTR_EA, NULL, 0, &run, 0, size);
 		if (!err)
 			err = ntfs_read_run_nb(sbi, &run, 0, ea_p, size, NULL);
 		run_close(&run);
 
 		if (err)
-			goto out;
+			goto out1;
 	} else {
 		void *p = resident_data_ex(attr_ea, size);
 
-		if (!p) {
-			err = -EINVAL;
-			goto out;
-		}
+		if (!p)
+			goto out1;
 		memcpy(ea_p, p, size);
 	}
 
 	memset(Add2Ptr(ea_p, size), 0, add_bytes);
+
+	/* Check all attributes for consistency. */
+	for (off = 0; off < size; off += ea_size) {
+		const struct EA_FULL *ef = Add2Ptr(ea_p, off);
+		u32 bytes = size - off;
+
+		/* Check if we can use field ea->size. */
+		if (bytes < sizeof(ef->size))
+			goto out1;
+
+		if (ef->size) {
+			ea_size = le32_to_cpu(ef->size);
+			if (ea_size > bytes)
+				goto out1;
+			continue;
+		}
+
+		/* Check if we can use fields ef->name_len and ef->elength. */
+		if (bytes < offsetof(struct EA_FULL, name))
+			goto out1;
+
+		ea_size = ALIGN(struct_size(ef, name,
+					    1 + ef->name_len +
+						    le16_to_cpu(ef->elength)),
+				4);
+		if (ea_size > bytes)
+			goto out1;
+	}
+
 	*ea = ea_p;
 	return 0;
 
-out:
+out1:
 	kfree(ea_p);
-	*ea = NULL;
+out:
+	ntfs_set_state(sbi, NTFS_DIRTY_DIRTY);
 	return err;
 }
 
@@ -163,6 +196,7 @@
 	const struct EA_FULL *ea;
 	u32 off, size;
 	int err;
+	int ea_size;
 	size_t ret;
 
 	err = ntfs_read_ea(ni, &ea_all, 0, &info);
@@ -175,10 +209,25 @@
 	size = le32_to_cpu(info->size);
 
 	/* Enumerate all xattrs. */
-	for (ret = 0, off = 0; off < size; off += unpacked_ea_size(ea)) {
+	ret = 0;
+	for (off = 0; off + sizeof(struct EA_FULL) < size; off += ea_size) {
 		ea = Add2Ptr(ea_all, off);
+		ea_size = unpacked_ea_size(ea);
+
+		if (!ea->name_len)
+			break;
+
+		if (ea->name_len > ea_size) {
+			ntfs_set_state(ni->mi.sbi, NTFS_DIRTY_ERROR);
+			err = -EINVAL; /* corrupted fs */
+			break;
+		}
 
 		if (buffer) {
+			/* Check if we can use field ea->name */
+			if (off + ea_size > size)
+				break;
+
 			if (ret + ea->name_len + 1 > bytes_per_buffer) {
 				err = -ERANGE;
 				goto out;
@@ -227,7 +276,8 @@
 		goto out;
 
 	/* Enumerate all xattrs. */
-	if (!find_ea(ea_all, le32_to_cpu(info->size), name, name_len, &off)) {
+	if (!find_ea(ea_all, le32_to_cpu(info->size), name, name_len, &off,
+		     NULL)) {
 		err = -ENODATA;
 		goto out;
 	}
@@ -269,7 +319,7 @@
 	struct EA_FULL *new_ea;
 	struct EA_FULL *ea_all = NULL;
 	size_t add, new_pack;
-	u32 off, size;
+	u32 off, size, ea_sz;
 	__le16 size_pack;
 	struct ATTRIB *attr;
 	struct ATTR_LIST_ENTRY *le;
@@ -303,9 +353,8 @@
 		size_pack = ea_info.size_pack;
 	}
 
-	if (info && find_ea(ea_all, size, name, name_len, &off)) {
+	if (info && find_ea(ea_all, size, name, name_len, &off, &ea_sz)) {
 		struct EA_FULL *ea;
-		size_t ea_sz;
 
 		if (flags & XATTR_CREATE) {
 			err = -EEXIST;
@@ -328,8 +377,6 @@
 		if (ea->flags & FILE_NEED_EA)
 			le16_add_cpu(&ea_info.count, -1);
 
-		ea_sz = unpacked_ea_size(ea);
-
 		le16_add_cpu(&ea_info.size_pack, 0 - packed_ea_size(ea));
 
 		memmove(ea, Add2Ptr(ea, ea_sz), size - off - ea_sz);
@@ -443,6 +490,11 @@
 		/* Delete xattr, ATTR_EA */
 		ni_remove_attr_le(ni, attr, mi, le);
 	} else if (attr->non_res) {
+		err = attr_load_runs_range(ni, ATTR_EA, NULL, 0, &ea_run, 0,
+					   size);
+		if (err)
+			goto out;
+
 		err = ntfs_sb_write_run(sbi, &ea_run, 0, ea_all, size, 0);
 		if (err)
 			goto out;
@@ -476,8 +528,7 @@
 }
 
 #ifdef CONFIG_NTFS3_FS_POSIX_ACL
-static struct posix_acl *ntfs_get_acl_ex(struct user_namespace *mnt_userns,
-					 struct inode *inode, int type,
+static struct posix_acl *ntfs_get_acl_ex(struct inode *inode, int type,
 					 int locked)
 {
 	struct ntfs_inode *ni = ntfs_i(inode);
@@ -512,7 +563,7 @@
 
 	/* Translate extended attribute to acl. */
 	if (err >= 0) {
-		acl = posix_acl_from_xattr(mnt_userns, buf, err);
+		acl = posix_acl_from_xattr(&init_user_ns, buf, err);
 	} else if (err == -ENODATA) {
 		acl = NULL;
 	} else {
@@ -535,37 +586,32 @@
 	if (rcu)
 		return ERR_PTR(-ECHILD);
 
-	/* TODO: init_user_ns? */
-	return ntfs_get_acl_ex(&init_user_ns, inode, type, 0);
+	return ntfs_get_acl_ex(inode, type, 0);
 }
 
 static noinline int ntfs_set_acl_ex(struct user_namespace *mnt_userns,
 				    struct inode *inode, struct posix_acl *acl,
-				    int type)
+				    int type, bool init_acl)
 {
 	const char *name;
 	size_t size, name_len;
-	void *value = NULL;
-	int err = 0;
+	void *value;
+	int err;
 	int flags;
+	umode_t mode;
 
 	if (S_ISLNK(inode->i_mode))
 		return -EOPNOTSUPP;
 
+	mode = inode->i_mode;
 	switch (type) {
 	case ACL_TYPE_ACCESS:
-		if (acl) {
-			umode_t mode = inode->i_mode;
-
+		/* Do not change i_mode if we are in init_acl */
+		if (acl && !init_acl) {
 			err = posix_acl_update_mode(mnt_userns, inode, &mode,
 						    &acl);
 			if (err)
-				goto out;
-
-			if (inode->i_mode != mode) {
-				inode->i_mode = mode;
-				mark_inode_dirty(inode);
-			}
+				return err;
 		}
 		name = XATTR_NAME_POSIX_ACL_ACCESS;
 		name_len = sizeof(XATTR_NAME_POSIX_ACL_ACCESS) - 1;
@@ -592,7 +638,7 @@
 		value = kmalloc(size, GFP_NOFS);
 		if (!value)
 			return -ENOMEM;
-		err = posix_acl_to_xattr(mnt_userns, acl, value, size);
+		err = posix_acl_to_xattr(&init_user_ns, acl, value, size);
 		if (err < 0)
 			goto out;
 		flags = 0;
@@ -601,8 +647,13 @@
 	err = ntfs_set_ea(inode, name, name_len, value, size, flags);
 	if (err == -ENODATA && !size)
 		err = 0; /* Removing non existed xattr. */
-	if (!err)
+	if (!err) {
 		set_cached_acl(inode, type, acl);
+		if (inode->i_mode != mode) {
+			inode->i_mode = mode;
+			mark_inode_dirty(inode);
+		}
+	}
 
 out:
 	kfree(value);
@@ -616,7 +667,7 @@
 int ntfs_set_acl(struct user_namespace *mnt_userns, struct inode *inode,
 		 struct posix_acl *acl, int type)
 {
-	return ntfs_set_acl_ex(mnt_userns, inode, acl, type);
+	return ntfs_set_acl_ex(mnt_userns, inode, acl, type, false);
 }
 
 /*
@@ -636,7 +687,7 @@
 
 	if (default_acl) {
 		err = ntfs_set_acl_ex(mnt_userns, inode, default_acl,
-				      ACL_TYPE_DEFAULT);
+				      ACL_TYPE_DEFAULT, true);
 		posix_acl_release(default_acl);
 	} else {
 		inode->i_default_acl = NULL;
@@ -647,7 +698,7 @@
 	else {
 		if (!err)
 			err = ntfs_set_acl_ex(mnt_userns, inode, acl,
-					      ACL_TYPE_ACCESS);
+					      ACL_TYPE_ACCESS, true);
 		posix_acl_release(acl);
 	}
 
@@ -901,6 +952,9 @@
 	err = ntfs_set_ea(inode, name, name_len, value, size, flags);
 
 out:
+	inode->i_ctime = current_time(inode);
+	mark_inode_dirty(inode);
+
 	return err;
 }
 
@@ -981,7 +1035,7 @@
 }
 
 // clang-format off
-static const struct xattr_handler ntfs_xattr_handler = {
+static const struct xattr_handler ntfs_other_xattr_handler = {
 	.prefix	= "",
 	.get	= ntfs_getxattr,
 	.set	= ntfs_setxattr,
@@ -989,7 +1043,11 @@
 };
 
 const struct xattr_handler *ntfs_xattr_handlers[] = {
-	&ntfs_xattr_handler,
+#ifdef CONFIG_NTFS3_FS_POSIX_ACL
+	&posix_acl_access_xattr_handler,
+	&posix_acl_default_xattr_handler,
+#endif
+	&ntfs_other_xattr_handler,
 	NULL,
 };
 // clang-format on
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/alloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/alloc.c
@@ -1796,6 +1796,14 @@
 
 	el = root_el;
 	while (el->l_tree_depth) {
+		if (unlikely(le16_to_cpu(el->l_tree_depth) >= OCFS2_MAX_PATH_DEPTH)) {
+			ocfs2_error(ocfs2_metadata_cache_get_super(ci),
+				    "Owner %llu has invalid tree depth %u in extent list\n",
+				    (unsigned long long)ocfs2_metadata_cache_owner(ci),
+				    le16_to_cpu(el->l_tree_depth));
+			ret = -EROFS;
+			goto out;
+		}
 		if (le16_to_cpu(el->l_next_free_rec) == 0) {
 			ocfs2_error(ocfs2_metadata_cache_get_super(ci),
 				    "Owner %llu has empty extent list at depth %u\n",
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/aops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/aops.c
@@ -156,9 +156,8 @@
 	err = ocfs2_extent_map_get_blocks(inode, iblock, &p_blkno, &count,
 					  &ext_flags);
 	if (err) {
-		mlog(ML_ERROR, "Error %d from get_blocks(0x%p, %llu, 1, "
-		     "%llu, NULL)\n", err, inode, (unsigned long long)iblock,
-		     (unsigned long long)p_blkno);
+		mlog(ML_ERROR, "get_blocks() failed, inode: 0x%p, "
+		     "block: %llu\n", inode, (unsigned long long)iblock);
 		goto bail;
 	}
 
@@ -1978,11 +1977,25 @@
 	}
 
 	if (unlikely(copied < len) && wc->w_target_page) {
+		loff_t new_isize;
+
 		if (!PageUptodate(wc->w_target_page))
 			copied = 0;
 
-		ocfs2_zero_new_buffers(wc->w_target_page, start+copied,
-				       start+len);
+		new_isize = max_t(loff_t, i_size_read(inode), pos + copied);
+		if (new_isize > page_offset(wc->w_target_page))
+			ocfs2_zero_new_buffers(wc->w_target_page, start+copied,
+					       start+len);
+		else {
+			/*
+			 * When page is fully beyond new isize (data copy
+			 * failed), do not bother zeroing the page. Invalidate
+			 * it instead so that writeback does not get confused
+			 * put page & buffer dirty bits into inconsistent
+			 * state.
+			 */
+			block_invalidatepage(wc->w_target_page, 0, PAGE_SIZE);
+		}
 	}
 	if (wc->w_target_page)
 		flush_dcache_page(wc->w_target_page);
@@ -2356,6 +2369,11 @@
 	}
 
 	list_for_each_entry(ue, &dwc->dw_zero_list, ue_node) {
+		ret = ocfs2_assure_trans_credits(handle, credits);
+		if (ret < 0) {
+			mlog_errno(ret);
+			break;
+		}
 		ret = ocfs2_mark_extent_written(inode, &et, handle,
 						ue->ue_cpos, 1,
 						ue->ue_phys,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/aops.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/aops.h
@@ -70,6 +70,8 @@
 	OCFS2_IOCB_NUM_LOCKS
 };
 
+#define ocfs2_iocb_init_rw_locked(iocb) \
+	(iocb->private = NULL)
 #define ocfs2_iocb_clear_rw_locked(iocb) \
 	clear_bit(OCFS2_IOCB_RW_LOCK, (unsigned long *)&iocb->private)
 #define ocfs2_iocb_rw_locked_level(iocb) \
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/buffer_head_io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/buffer_head_io.c
@@ -235,7 +235,6 @@
 		if (bhs[i] == NULL) {
 			bhs[i] = sb_getblk(sb, block++);
 			if (bhs[i] == NULL) {
-				ocfs2_metadata_cache_io_unlock(ci);
 				status = -ENOMEM;
 				mlog_errno(status);
 				/* Don't forget to put previous bh! */
@@ -389,7 +388,8 @@
 		/* Always set the buffer in the cache, even if it was
 		 * a forced read, or read-ahead which hasn't yet
 		 * completed. */
-		ocfs2_set_buffer_uptodate(ci, bh);
+		if (bh)
+			ocfs2_set_buffer_uptodate(ci, bh);
 	}
 	ocfs2_metadata_cache_io_unlock(ci);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/dir.c
@@ -294,13 +294,16 @@
  * bh passed here can be an inode block or a dir data block, depending
  * on the inode inline data flag.
  */
-static int ocfs2_check_dir_entry(struct inode * dir,
-				 struct ocfs2_dir_entry * de,
-				 struct buffer_head * bh,
+static int ocfs2_check_dir_entry(struct inode *dir,
+				 struct ocfs2_dir_entry *de,
+				 struct buffer_head *bh,
+				 char *buf,
+				 unsigned int size,
 				 unsigned long offset)
 {
 	const char *error_msg = NULL;
 	const int rlen = le16_to_cpu(de->rec_len);
+	const unsigned long next_offset = ((char *) de - buf) + rlen;
 
 	if (unlikely(rlen < OCFS2_DIR_REC_LEN(1)))
 		error_msg = "rec_len is smaller than minimal";
@@ -308,9 +311,11 @@
 		error_msg = "rec_len % 4 != 0";
 	else if (unlikely(rlen < OCFS2_DIR_REC_LEN(de->name_len)))
 		error_msg = "rec_len is too small for name_len";
-	else if (unlikely(
-		 ((char *) de - bh->b_data) + rlen > dir->i_sb->s_blocksize))
-		error_msg = "directory entry across blocks";
+	else if (unlikely(next_offset > size))
+		error_msg = "directory entry overrun";
+	else if (unlikely(next_offset > size - OCFS2_DIR_REC_LEN(1)) &&
+		 next_offset != size)
+		error_msg = "directory entry too close to end";
 
 	if (unlikely(error_msg != NULL))
 		mlog(ML_ERROR, "bad entry in directory #%llu: %s - "
@@ -352,16 +357,17 @@
 	de_buf = first_de;
 	dlimit = de_buf + bytes;
 
-	while (de_buf < dlimit) {
+	while (de_buf < dlimit - OCFS2_DIR_MEMBER_LEN) {
 		/* this code is executed quadratically often */
 		/* do minimal checking `by hand' */
 
 		de = (struct ocfs2_dir_entry *) de_buf;
 
-		if (de_buf + namelen <= dlimit &&
+		if (de->name + namelen <= dlimit &&
 		    ocfs2_match(namelen, name, de)) {
 			/* found a match - just to be sure, do a full check */
-			if (!ocfs2_check_dir_entry(dir, de, bh, offset)) {
+			if (!ocfs2_check_dir_entry(dir, de, bh, first_de,
+						   bytes, offset)) {
 				ret = -1;
 				goto bail;
 			}
@@ -1059,26 +1065,39 @@
 {
 	struct buffer_head *bh;
 	struct ocfs2_dir_entry *res_dir = NULL;
+	int ret = 0;
 
 	if (ocfs2_dir_indexed(dir))
 		return ocfs2_find_entry_dx(name, namelen, dir, lookup);
 
+	if (unlikely(i_size_read(dir) <= 0)) {
+		ret = -EFSCORRUPTED;
+		mlog_errno(ret);
+		goto out;
+	}
 	/*
 	 * The unindexed dir code only uses part of the lookup
 	 * structure, so there's no reason to push it down further
 	 * than this.
 	 */
-	if (OCFS2_I(dir)->ip_dyn_features & OCFS2_INLINE_DATA_FL)
+	if (OCFS2_I(dir)->ip_dyn_features & OCFS2_INLINE_DATA_FL) {
+		if (unlikely(i_size_read(dir) > dir->i_sb->s_blocksize)) {
+			ret = -EFSCORRUPTED;
+			mlog_errno(ret);
+			goto out;
+		}
 		bh = ocfs2_find_entry_id(name, namelen, dir, &res_dir);
-	else
+	} else {
 		bh = ocfs2_find_entry_el(name, namelen, dir, &res_dir);
+	}
 
 	if (bh == NULL)
 		return -ENOENT;
 
 	lookup->dl_leaf_bh = bh;
 	lookup->dl_entry = res_dir;
-	return 0;
+out:
+	return ret;
 }
 
 /*
@@ -1138,7 +1157,7 @@
 	pde = NULL;
 	de = (struct ocfs2_dir_entry *) first_de;
 	while (i < bytes) {
-		if (!ocfs2_check_dir_entry(dir, de, bh, i)) {
+		if (!ocfs2_check_dir_entry(dir, de, bh, first_de, bytes, i)) {
 			status = -EIO;
 			mlog_errno(status);
 			goto bail;
@@ -1638,7 +1657,8 @@
 		/* These checks should've already been passed by the
 		 * prepare function, but I guess we can leave them
 		 * here anyway. */
-		if (!ocfs2_check_dir_entry(dir, de, insert_bh, offset)) {
+		if (!ocfs2_check_dir_entry(dir, de, insert_bh, data_start,
+					   size, offset)) {
 			retval = -ENOENT;
 			goto bail;
 		}
@@ -1776,7 +1796,8 @@
 		}
 
 		de = (struct ocfs2_dir_entry *) (data->id_data + ctx->pos);
-		if (!ocfs2_check_dir_entry(inode, de, di_bh, ctx->pos)) {
+		if (!ocfs2_check_dir_entry(inode, de, di_bh, (char *)data->id_data,
+					   i_size_read(inode), ctx->pos)) {
 			/* On error, skip the f_pos to the end. */
 			ctx->pos = i_size_read(inode);
 			break;
@@ -1869,7 +1890,8 @@
 		while (ctx->pos < i_size_read(inode)
 		       && offset < sb->s_blocksize) {
 			de = (struct ocfs2_dir_entry *) (bh->b_data + offset);
-			if (!ocfs2_check_dir_entry(inode, de, bh, offset)) {
+			if (!ocfs2_check_dir_entry(inode, de, bh, bh->b_data,
+						   sb->s_blocksize, offset)) {
 				/* On error, skip the f_pos to the
 				   next block. */
 				ctx->pos = (ctx->pos | (sb->s_blocksize - 1)) + 1;
@@ -2002,6 +2024,7 @@
  *
  * Return 0 if the name does not exist
  * Return -EEXIST if the directory contains the name
+ * Return -EFSCORRUPTED if found corruption
  *
  * Callers should have i_mutex + a cluster lock on dir
  */
@@ -2015,9 +2038,12 @@
 	trace_ocfs2_check_dir_for_entry(
 		(unsigned long long)OCFS2_I(dir)->ip_blkno, namelen, name);
 
-	if (ocfs2_find_entry(name, namelen, dir, &lookup) == 0) {
+	ret = ocfs2_find_entry(name, namelen, dir, &lookup);
+	if (ret == 0) {
 		ret = -EEXIST;
 		mlog_errno(ret);
+	} else if (ret == -ENOENT) {
+		ret = 0;
 	}
 
 	ocfs2_free_dir_lookup_result(&lookup);
@@ -3341,7 +3367,7 @@
 	struct super_block *sb = dir->i_sb;
 	struct ocfs2_dinode *di = (struct ocfs2_dinode *)di_bh->b_data;
 	struct ocfs2_dir_entry *de, *last_de = NULL;
-	char *de_buf, *limit;
+	char *first_de, *de_buf, *limit;
 	unsigned long offset = 0;
 	unsigned int rec_len, new_rec_len, free_space = dir->i_sb->s_blocksize;
 
@@ -3354,14 +3380,16 @@
 	else
 		free_space = dir->i_sb->s_blocksize - i_size_read(dir);
 
-	de_buf = di->id2.i_data.id_data;
+	first_de = di->id2.i_data.id_data;
+	de_buf = first_de;
 	limit = de_buf + i_size_read(dir);
 	rec_len = OCFS2_DIR_REC_LEN(namelen);
 
 	while (de_buf < limit) {
 		de = (struct ocfs2_dir_entry *)de_buf;
 
-		if (!ocfs2_check_dir_entry(dir, de, di_bh, offset)) {
+		if (!ocfs2_check_dir_entry(dir, de, di_bh, first_de,
+					   i_size_read(dir), offset)) {
 			ret = -ENOENT;
 			goto out;
 		}
@@ -3443,7 +3471,8 @@
 			/* move to next block */
 			de = (struct ocfs2_dir_entry *) bh->b_data;
 		}
-		if (!ocfs2_check_dir_entry(dir, de, bh, offset)) {
+		if (!ocfs2_check_dir_entry(dir, de, bh, bh->b_data, blocksize,
+					   offset)) {
 			status = -ENOENT;
 			goto bail;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/dlmfs/userdlm.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/dlmfs/userdlm.c
@@ -433,6 +433,11 @@
 	}
 
 	spin_lock(&lockres->l_lock);
+	if (lockres->l_flags & USER_LOCK_IN_TEARDOWN) {
+		spin_unlock(&lockres->l_lock);
+		status = -EAGAIN;
+		goto bail;
+	}
 
 	/* We only compare against the currently granted level
 	 * here. If the lock is blocked waiting on a downconvert,
@@ -595,7 +600,7 @@
 	spin_lock(&lockres->l_lock);
 	if (lockres->l_flags & USER_LOCK_IN_TEARDOWN) {
 		spin_unlock(&lockres->l_lock);
-		return 0;
+		goto bail;
 	}
 
 	lockres->l_flags |= USER_LOCK_IN_TEARDOWN;
@@ -609,12 +614,17 @@
 	}
 
 	if (lockres->l_ro_holders || lockres->l_ex_holders) {
+		lockres->l_flags &= ~USER_LOCK_IN_TEARDOWN;
 		spin_unlock(&lockres->l_lock);
 		goto bail;
 	}
 
 	status = 0;
 	if (!(lockres->l_flags & USER_LOCK_ATTACHED)) {
+		/*
+		 * lock is never requested, leave USER_LOCK_IN_TEARDOWN set
+		 * to avoid new lock request coming in.
+		 */
 		spin_unlock(&lockres->l_lock);
 		goto bail;
 	}
@@ -625,6 +635,10 @@
 
 	status = ocfs2_dlm_unlock(conn, &lockres->l_lksb, DLM_LKF_VALBLK);
 	if (status) {
+		spin_lock(&lockres->l_lock);
+		lockres->l_flags &= ~USER_LOCK_IN_TEARDOWN;
+		lockres->l_flags &= ~USER_LOCK_BUSY;
+		spin_unlock(&lockres->l_lock);
 		user_log_dlm_error("ocfs2_dlm_unlock", status, lockres);
 		goto bail;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/dlmglue.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/dlmglue.c
@@ -3108,6 +3108,7 @@
 	struct ocfs2_lock_res *iter = v;
 	struct ocfs2_lock_res *dummy = &priv->p_iter_res;
 
+	(*pos)++;
 	spin_lock(&ocfs2_dlm_tracking_lock);
 	iter = ocfs2_dlm_next_res(iter, priv);
 	list_del_init(&dummy->l_debug_list);
@@ -3403,10 +3404,12 @@
 	ocfs2_lock_res_free(&osb->osb_nfs_sync_lockres);
 	ocfs2_lock_res_free(&osb->osb_orphan_scan.os_lockres);
 
-	ocfs2_cluster_disconnect(osb->cconn, hangup_pending);
-	osb->cconn = NULL;
+	if (osb->cconn) {
+		ocfs2_cluster_disconnect(osb->cconn, hangup_pending);
+		osb->cconn = NULL;
 
-	ocfs2_dlm_shutdown_debug(osb);
+		ocfs2_dlm_shutdown_debug(osb);
+	}
 }
 
 static int ocfs2_drop_lock(struct ocfs2_super *osb,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/file.c
@@ -476,10 +476,11 @@
 	 * greater than page size, so we have to truncate them
 	 * anyway.
 	 */
-	unmap_mapping_range(inode->i_mapping, new_i_size + PAGE_SIZE - 1, 0, 1);
-	truncate_inode_pages(inode->i_mapping, new_i_size);
 
 	if (OCFS2_I(inode)->ip_dyn_features & OCFS2_INLINE_DATA_FL) {
+		unmap_mapping_range(inode->i_mapping,
+				    new_i_size + PAGE_SIZE - 1, 0, 1);
+		truncate_inode_pages(inode->i_mapping, new_i_size);
 		status = ocfs2_truncate_inline(inode, di_bh, new_i_size,
 					       i_size_read(inode), 1);
 		if (status)
@@ -498,6 +499,9 @@
 		goto bail_unlock_sem;
 	}
 
+	unmap_mapping_range(inode->i_mapping, new_i_size + PAGE_SIZE - 1, 0, 1);
+	truncate_inode_pages(inode->i_mapping, new_i_size);
+
 	status = ocfs2_commit_truncate(osb, inode, di_bh);
 	if (status < 0) {
 		mlog_errno(status);
@@ -1128,9 +1132,12 @@
 	trace_ocfs2_setattr(inode, dentry,
 			    (unsigned long long)OCFS2_I(inode)->ip_blkno,
 			    dentry->d_name.len, dentry->d_name.name,
-			    attr->ia_valid, attr->ia_mode,
-			    from_kuid(&init_user_ns, attr->ia_uid),
-			    from_kgid(&init_user_ns, attr->ia_gid));
+			    attr->ia_valid,
+				attr->ia_valid & ATTR_MODE ? attr->ia_mode : 0,
+				attr->ia_valid & ATTR_UID ?
+					from_kuid(&init_user_ns, attr->ia_uid) : 0,
+				attr->ia_valid & ATTR_GID ?
+					from_kgid(&init_user_ns, attr->ia_gid) : 0);
 
 	/* ensuring we don't even attempt to truncate a symlink */
 	if (S_ISLNK(inode->i_mode))
@@ -1783,6 +1790,14 @@
 		return 0;
 
 	if (OCFS2_I(inode)->ip_dyn_features & OCFS2_INLINE_DATA_FL) {
+		int id_count = ocfs2_max_inline_data_with_xattr(inode->i_sb, di);
+
+		if (byte_start > id_count || byte_start + byte_len > id_count) {
+			ret = -EINVAL;
+			mlog_errno(ret);
+			goto out;
+		}
+
 		ret = ocfs2_truncate_inline(inode, di_bh, byte_start,
 					    byte_start + byte_len, 0);
 		if (ret) {
@@ -1936,6 +1951,8 @@
 
 	inode_lock(inode);
 
+	/* Wait all existing dio workers, newcomers will block on i_rwsem */
+	inode_dio_wait(inode);
 	/*
 	 * This prevents concurrent writes on other nodes
 	 */
@@ -1990,7 +2007,7 @@
 		}
 	}
 
-	if (file && should_remove_suid(file->f_path.dentry)) {
+	if (file && setattr_should_drop_suidgid(&init_user_ns, file_inode(file))) {
 		ret = __ocfs2_write_remove_suid(inode, di_bh);
 		if (ret) {
 			mlog_errno(ret);
@@ -2099,14 +2116,20 @@
 	struct ocfs2_space_resv sr;
 	int change_size = 1;
 	int cmd = OCFS2_IOC_RESVSP64;
+	int ret = 0;
 
 	if (mode & ~(FALLOC_FL_KEEP_SIZE | FALLOC_FL_PUNCH_HOLE))
 		return -EOPNOTSUPP;
 	if (!ocfs2_writes_unwritten_extents(osb))
 		return -EOPNOTSUPP;
 
-	if (mode & FALLOC_FL_KEEP_SIZE)
+	if (mode & FALLOC_FL_KEEP_SIZE) {
 		change_size = 0;
+	} else {
+		ret = inode_newsize_ok(inode, offset + len);
+		if (ret)
+			return ret;
+	}
 
 	if (mode & FALLOC_FL_PUNCH_HOLE)
 		cmd = OCFS2_IOC_UNRESVSP64;
@@ -2278,7 +2301,7 @@
 		 * inode. There's also the dinode i_size state which
 		 * can be lost via setattr during extending writes (we
 		 * set inode->i_size at the end of a write. */
-		if (should_remove_suid(dentry)) {
+		if (setattr_should_drop_suidgid(&init_user_ns, inode)) {
 			if (meta_level == 0) {
 				ocfs2_inode_unlock_for_extent_tree(inode,
 								   &di_bh,
@@ -2378,6 +2401,8 @@
 	} else
 		inode_lock(inode);
 
+	ocfs2_iocb_init_rw_locked(iocb);
+
 	/*
 	 * Concurrent O_DIRECT writes are allowed with
 	 * mount_option "coherency=buffered".
@@ -2524,6 +2549,8 @@
 	if (!direct_io && nowait)
 		return -EOPNOTSUPP;
 
+	ocfs2_iocb_init_rw_locked(iocb);
+
 	/*
 	 * buffered reads protect themselves in ->readpage().  O_DIRECT reads
 	 * need locks to protect pending reads from racing with truncate.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/journal.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/journal.c
@@ -157,7 +157,7 @@
 	replay_map->rm_state = REPLAY_DONE;
 }
 
-static void ocfs2_free_replay_slots(struct ocfs2_super *osb)
+void ocfs2_free_replay_slots(struct ocfs2_super *osb)
 {
 	struct ocfs2_replay_map *replay_map = osb->replay_map;
 
@@ -448,6 +448,23 @@
 }
 
 /*
+ * Make sure handle has at least 'nblocks' credits available. If it does not
+ * have that many credits available, we will try to extend the handle to have
+ * enough credits. If that fails, we will restart transaction to have enough
+ * credits. Similar notes regarding data consistency and locking implications
+ * as for ocfs2_extend_trans() apply here.
+ */
+int ocfs2_assure_trans_credits(handle_t *handle, int nblocks)
+{
+	int old_nblks = jbd2_handle_buffer_credits(handle);
+
+	trace_ocfs2_assure_trans_credits(old_nblks);
+	if (old_nblks >= nblocks)
+		return 0;
+	return ocfs2_extend_trans(handle, nblocks - old_nblks);
+}
+
+/*
  * If we have fewer than thresh credits, extend by OCFS2_MAX_TRANS_DATA.
  * If that fails, restart the transaction & regain write access for the
  * buffer head which is used for metadata modifications.
@@ -977,7 +994,7 @@
 	if (!igrab(inode))
 		BUG();
 
-	num_running_trans = atomic_read(&(osb->journal->j_num_trans));
+	num_running_trans = atomic_read(&(journal->j_num_trans));
 	trace_ocfs2_journal_shutdown(num_running_trans);
 
 	/* Do a commit_cache here. It will flush our journal, *and*
@@ -996,9 +1013,10 @@
 		osb->commit_task = NULL;
 	}
 
-	BUG_ON(atomic_read(&(osb->journal->j_num_trans)) != 0);
+	BUG_ON(atomic_read(&(journal->j_num_trans)) != 0);
 
-	if (ocfs2_mount_local(osb)) {
+	if (ocfs2_mount_local(osb) &&
+	    (journal->j_journal->j_flags & JBD2_LOADED)) {
 		jbd2_journal_lock_updates(journal->j_journal);
 		status = jbd2_journal_flush(journal->j_journal, 0);
 		jbd2_journal_unlock_updates(journal->j_journal);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/journal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/journal.h
@@ -150,6 +150,7 @@
 void ocfs2_recovery_exit(struct ocfs2_super *osb);
 
 int ocfs2_compute_replay_slots(struct ocfs2_super *osb);
+void ocfs2_free_replay_slots(struct ocfs2_super *osb);
 /*
  *  Journal Control:
  *  Initialize, Load, Shutdown, Wipe a journal.
@@ -241,6 +242,8 @@
 int			     ocfs2_commit_trans(struct ocfs2_super *osb,
 						handle_t *handle);
 int			     ocfs2_extend_trans(handle_t *handle, int nblocks);
+int			     ocfs2_assure_trans_credits(handle_t *handle,
+						int nblocks);
 int			     ocfs2_allocate_extend_trans(handle_t *handle,
 						int thresh);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/move_extents.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/move_extents.c
@@ -105,14 +105,6 @@
 	 */
 	replace_rec.e_flags = ext_flags & ~OCFS2_EXT_REFCOUNTED;
 
-	ret = ocfs2_journal_access_di(handle, INODE_CACHE(inode),
-				      context->et.et_root_bh,
-				      OCFS2_JOURNAL_ACCESS_WRITE);
-	if (ret) {
-		mlog_errno(ret);
-		goto out;
-	}
-
 	ret = ocfs2_split_extent(handle, &context->et, path, index,
 				 &replace_rec, context->meta_ac,
 				 &context->dealloc);
@@ -121,8 +113,6 @@
 		goto out;
 	}
 
-	ocfs2_journal_dirty(handle, context->et.et_root_bh);
-
 	context->new_phys_cpos = new_p_cpos;
 
 	/*
@@ -444,7 +434,7 @@
 			bg = (struct ocfs2_group_desc *)gd_bh->b_data;
 
 			if (vict_blkno < (le64_to_cpu(bg->bg_blkno) +
-						le16_to_cpu(bg->bg_bits))) {
+						(le16_to_cpu(bg->bg_bits) << bits_per_unit))) {
 
 				*ret_bh = gd_bh;
 				*vict_bit = (vict_blkno - blkno) >>
@@ -559,6 +549,7 @@
 			last_free_bits++;
 
 		if (last_free_bits == move_len) {
+			i -= move_len;
 			*goal_bit = i;
 			*phys_cpos = base_cpos + i;
 			break;
@@ -1030,18 +1021,19 @@
 
 	context->range = &range;
 
+	/*
+	 * ok, the default theshold for the defragmentation
+	 * is 1M, since our maximum clustersize was 1M also.
+	 * any thought?
+	 */
+	if (!range.me_threshold)
+		range.me_threshold = 1024 * 1024;
+
+	if (range.me_threshold > i_size_read(inode))
+		range.me_threshold = i_size_read(inode);
+
 	if (range.me_flags & OCFS2_MOVE_EXT_FL_AUTO_DEFRAG) {
 		context->auto_defrag = 1;
-		/*
-		 * ok, the default theshold for the defragmentation
-		 * is 1M, since our maximum clustersize was 1M also.
-		 * any thought?
-		 */
-		if (!range.me_threshold)
-			range.me_threshold = 1024 * 1024;
-
-		if (range.me_threshold > i_size_read(inode))
-			range.me_threshold = i_size_read(inode);
 
 		if (range.me_flags & OCFS2_MOVE_EXT_FL_PART_DEFRAG)
 			context->partial = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/namei.c
@@ -197,10 +197,13 @@
 	 * callers. */
 	if (S_ISDIR(mode))
 		set_nlink(inode, 2);
+	mode = mode_strip_sgid(&init_user_ns, dir, mode);
 	inode_init_owner(&init_user_ns, inode, dir, mode);
 	status = dquot_initialize(inode);
-	if (status)
+	if (status) {
+		iput(inode);
 		return ERR_PTR(status);
+	}
 
 	return inode;
 }
@@ -231,6 +234,7 @@
 	handle_t *handle = NULL;
 	struct ocfs2_super *osb;
 	struct ocfs2_dinode *dirfe;
+	struct ocfs2_dinode *fe = NULL;
 	struct buffer_head *new_fe_bh = NULL;
 	struct inode *inode = NULL;
 	struct ocfs2_alloc_context *inode_ac = NULL;
@@ -240,6 +244,7 @@
 	int want_meta = 0;
 	int xattr_credits = 0;
 	struct ocfs2_security_xattr_info si = {
+		.name = NULL,
 		.enable = 1,
 	};
 	int did_quota_inode = 0;
@@ -381,6 +386,7 @@
 		goto leave;
 	}
 
+	fe = (struct ocfs2_dinode *) new_fe_bh->b_data;
 	if (S_ISDIR(mode)) {
 		status = ocfs2_fill_new_dir(osb, handle, dir, inode,
 					    new_fe_bh, data_ac, meta_ac);
@@ -453,8 +459,11 @@
 leave:
 	if (status < 0 && did_quota_inode)
 		dquot_free_inode(inode);
-	if (handle)
+	if (handle) {
+		if (status < 0 && fe)
+			ocfs2_set_links_count(fe, 0);
 		ocfs2_commit_trans(osb, handle);
+	}
 
 	ocfs2_inode_unlock(dir, 1);
 	if (did_block_signals)
@@ -559,7 +568,7 @@
 	fe->i_last_eb_blk = 0;
 	strcpy(fe->i_signature, OCFS2_INODE_SIGNATURE);
 	fe->i_flags |= cpu_to_le32(OCFS2_VALID_FL);
-	ktime_get_real_ts64(&ts);
+	ktime_get_coarse_real_ts64(&ts);
 	fe->i_atime = fe->i_ctime = fe->i_mtime =
 		cpu_to_le64(ts.tv_sec);
 	fe->i_mtime_nsec = fe->i_ctime_nsec = fe->i_atime_nsec =
@@ -631,18 +640,9 @@
 		return status;
 	}
 
-	status = __ocfs2_mknod_locked(dir, inode, dev, new_fe_bh,
+	return __ocfs2_mknod_locked(dir, inode, dev, new_fe_bh,
 				    parent_fe_bh, handle, inode_ac,
 				    fe_blkno, suballoc_loc, suballoc_bit);
-	if (status < 0) {
-		u64 bg_blkno = ocfs2_which_suballoc_group(fe_blkno, suballoc_bit);
-		int tmp = ocfs2_free_suballoc_bits(handle, inode_ac->ac_inode,
-				inode_ac->ac_bh, suballoc_bit, bg_blkno, 1);
-		if (tmp)
-			mlog_errno(tmp);
-	}
-
-	return status;
 }
 
 static int ocfs2_mkdir(struct user_namespace *mnt_userns,
@@ -1537,6 +1537,10 @@
 		status = ocfs2_add_entry(handle, new_dentry, old_inode,
 					 OCFS2_I(old_inode)->ip_blkno,
 					 new_dir_bh, &target_insert);
+		if (status < 0) {
+			mlog_errno(status);
+			goto bail;
+		}
 	}
 
 	old_inode->i_ctime = current_time(old_inode);
@@ -1808,6 +1812,7 @@
 	int want_clusters = 0;
 	int xattr_credits = 0;
 	struct ocfs2_security_xattr_info si = {
+		.name = NULL,
 		.enable = 1,
 	};
 	int did_quota = 0, did_quota_inode = 0;
@@ -2027,8 +2032,11 @@
 					ocfs2_clusters_to_bytes(osb->sb, 1));
 	if (status < 0 && did_quota_inode)
 		dquot_free_inode(inode);
-	if (handle)
+	if (handle) {
+		if (status < 0 && fe)
+			ocfs2_set_links_count(fe, 0);
 		ocfs2_commit_trans(osb, handle);
+	}
 
 	ocfs2_inode_unlock(dir, 1);
 	if (did_block_signals)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/ocfs2.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/ocfs2.h
@@ -277,7 +277,6 @@
 	OCFS2_MOUNT_JOURNAL_ASYNC_COMMIT = 1 << 15,  /* Journal Async Commit */
 	OCFS2_MOUNT_ERRORS_CONT = 1 << 16, /* Return EIO to the calling process on error */
 	OCFS2_MOUNT_ERRORS_ROFS = 1 << 17, /* Change filesystem to read-only on error */
-	OCFS2_MOUNT_NOCLUSTER = 1 << 18, /* No cluster aware filesystem mount */
 };
 
 #define OCFS2_OSB_SOFT_RO	0x0001
@@ -673,8 +672,7 @@
 
 static inline int ocfs2_mount_local(struct ocfs2_super *osb)
 {
-	return ((osb->s_feature_incompat & OCFS2_FEATURE_INCOMPAT_LOCAL_MOUNT)
-		|| (osb->s_mount_opt & OCFS2_MOUNT_NOCLUSTER));
+	return (osb->s_feature_incompat & OCFS2_FEATURE_INCOMPAT_LOCAL_MOUNT);
 }
 
 static inline int ocfs2_uses_extended_slot_map(struct ocfs2_super *osb)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/ocfs2_trace.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/ocfs2_trace.h
@@ -2578,6 +2578,8 @@
 
 DEFINE_OCFS2_INT_INT_EVENT(ocfs2_extend_trans);
 
+DEFINE_OCFS2_INT_EVENT(ocfs2_assure_trans_credits);
+
 DEFINE_OCFS2_INT_EVENT(ocfs2_extend_trans_restart);
 
 DEFINE_OCFS2_INT_INT_EVENT(ocfs2_allocate_extend_trans);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/quota_global.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/quota_global.c
@@ -337,7 +337,6 @@
 /* Read information header from global quota file */
 int ocfs2_global_read_info(struct super_block *sb, int type)
 {
-	struct inode *gqinode = NULL;
 	unsigned int ino[OCFS2_MAXQUOTAS] = { USER_QUOTA_SYSTEM_INODE,
 					      GROUP_QUOTA_SYSTEM_INODE };
 	struct ocfs2_global_disk_dqinfo dinfo;
@@ -346,29 +345,31 @@
 	u64 pcount;
 	int status;
 
+	oinfo->dqi_gi.dqi_sb = sb;
+	oinfo->dqi_gi.dqi_type = type;
+	ocfs2_qinfo_lock_res_init(&oinfo->dqi_gqlock, oinfo);
+	oinfo->dqi_gi.dqi_entry_size = sizeof(struct ocfs2_global_disk_dqblk);
+	oinfo->dqi_gi.dqi_ops = &ocfs2_global_ops;
+	oinfo->dqi_gqi_bh = NULL;
+	oinfo->dqi_gqi_count = 0;
+
 	/* Read global header */
-	gqinode = ocfs2_get_system_file_inode(OCFS2_SB(sb), ino[type],
+	oinfo->dqi_gqinode = ocfs2_get_system_file_inode(OCFS2_SB(sb), ino[type],
 			OCFS2_INVALID_SLOT);
-	if (!gqinode) {
+	if (!oinfo->dqi_gqinode) {
 		mlog(ML_ERROR, "failed to get global quota inode (type=%d)\n",
 			type);
 		status = -EINVAL;
 		goto out_err;
 	}
-	oinfo->dqi_gi.dqi_sb = sb;
-	oinfo->dqi_gi.dqi_type = type;
-	oinfo->dqi_gi.dqi_entry_size = sizeof(struct ocfs2_global_disk_dqblk);
-	oinfo->dqi_gi.dqi_ops = &ocfs2_global_ops;
-	oinfo->dqi_gqi_bh = NULL;
-	oinfo->dqi_gqi_count = 0;
-	oinfo->dqi_gqinode = gqinode;
+
 	status = ocfs2_lock_global_qf(oinfo, 0);
 	if (status < 0) {
 		mlog_errno(status);
 		goto out_err;
 	}
 
-	status = ocfs2_extent_map_get_blocks(gqinode, 0, &oinfo->dqi_giblk,
+	status = ocfs2_extent_map_get_blocks(oinfo->dqi_gqinode, 0, &oinfo->dqi_giblk,
 					     &pcount, NULL);
 	if (status < 0)
 		goto out_unlock;
@@ -748,6 +749,11 @@
 	handle = ocfs2_start_trans(osb,
 		ocfs2_calc_qdel_credits(dquot->dq_sb, dquot->dq_id.type));
 	if (IS_ERR(handle)) {
+		/*
+		 * Mark dquot as inactive to avoid endless cycle in
+		 * quota_release_workfn().
+		 */
+		clear_bit(DQ_ACTIVE_B, &dquot->dq_flags);
 		status = PTR_ERR(handle);
 		mlog_errno(status);
 		goto out_ilock;
@@ -880,7 +886,7 @@
 	int status = 0;
 
 	trace_ocfs2_get_next_id(from_kqid(&init_user_ns, *qid), type);
-	if (!sb_has_quota_loaded(sb, type)) {
+	if (!sb_has_quota_active(sb, type)) {
 		status = -ESRCH;
 		goto out;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/quota_local.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/quota_local.c
@@ -689,7 +689,7 @@
 	int status;
 	struct buffer_head *bh = NULL;
 	struct ocfs2_quota_recovery *rec;
-	int locked = 0;
+	int locked = 0, global_read = 0;
 
 	info->dqi_max_spc_limit = 0x7fffffffffffffffLL;
 	info->dqi_max_ino_limit = 0x7fffffffffffffffLL;
@@ -697,13 +697,12 @@
 	if (!oinfo) {
 		mlog(ML_ERROR, "failed to allocate memory for ocfs2 quota"
 			       " info.");
+		status = -ENOMEM;
 		goto out_err;
 	}
 	info->dqi_priv = oinfo;
 	oinfo->dqi_type = type;
 	INIT_LIST_HEAD(&oinfo->dqi_chunk);
-	oinfo->dqi_gqinode = NULL;
-	ocfs2_qinfo_lock_res_init(&oinfo->dqi_gqlock, oinfo);
 	oinfo->dqi_rec = NULL;
 	oinfo->dqi_lqi_bh = NULL;
 	oinfo->dqi_libh = NULL;
@@ -711,6 +710,7 @@
 	status = ocfs2_global_read_info(sb, type);
 	if (status < 0)
 		goto out_err;
+	global_read = 1;
 
 	status = ocfs2_inode_lock(lqinode, &oinfo->dqi_lqi_bh, 1);
 	if (status < 0) {
@@ -781,10 +781,12 @@
 		if (locked)
 			ocfs2_inode_unlock(lqinode, 1);
 		ocfs2_release_local_quota_bitmaps(&oinfo->dqi_chunk);
+		if (global_read)
+			cancel_delayed_work_sync(&oinfo->dqi_sync_work);
 		kfree(oinfo);
 	}
 	brelse(bh);
-	return -1;
+	return status;
 }
 
 /* Write local info to quota file */
@@ -813,7 +815,7 @@
 	struct ocfs2_quota_chunk *chunk;
 	struct ocfs2_local_disk_chunk *dchunk;
 	int mark_clean = 1, len;
-	int status;
+	int status = 0;
 
 	iput(oinfo->dqi_gqinode);
 	ocfs2_simple_drop_lockres(OCFS2_SB(sb), &oinfo->dqi_gqlock);
@@ -855,17 +857,15 @@
 				 oinfo->dqi_libh,
 				 olq_update_info,
 				 info);
-	if (status < 0) {
+	if (status < 0)
 		mlog_errno(status);
-		goto out;
-	}
-
 out:
 	ocfs2_inode_unlock(sb_dqopt(sb)->files[type], 1);
 	brelse(oinfo->dqi_libh);
 	brelse(oinfo->dqi_lqi_bh);
 	kfree(oinfo);
-	return 0;
+	info->dqi_priv = NULL;
+	return status;
 }
 
 static void olq_set_dquot(struct buffer_head *bh, void *private)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/refcounttree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/refcounttree.c
@@ -25,6 +25,7 @@
 #include "namei.h"
 #include "ocfs2_trace.h"
 #include "file.h"
+#include "symlink.h"
 
 #include <linux/bio.h>
 #include <linux/blkdev.h>
@@ -4182,8 +4183,9 @@
 	int ret;
 	struct inode *inode = d_inode(old_dentry);
 	struct buffer_head *new_bh = NULL;
+	struct ocfs2_inode_info *oi = OCFS2_I(inode);
 
-	if (OCFS2_I(inode)->ip_flags & OCFS2_INODE_SYSTEM_FILE) {
+	if (oi->ip_flags & OCFS2_INODE_SYSTEM_FILE) {
 		ret = -EINVAL;
 		mlog_errno(ret);
 		goto out;
@@ -4209,6 +4211,26 @@
 		goto out_unlock;
 	}
 
+	if ((oi->ip_dyn_features & OCFS2_HAS_XATTR_FL) &&
+	    (oi->ip_dyn_features & OCFS2_INLINE_XATTR_FL)) {
+		/*
+		 * Adjust extent record count to reserve space for extended attribute.
+		 * Inline data count had been adjusted in ocfs2_duplicate_inline_data().
+		 */
+		struct ocfs2_inode_info *new_oi = OCFS2_I(new_inode);
+
+		if (!(new_oi->ip_dyn_features & OCFS2_INLINE_DATA_FL) &&
+		    !(ocfs2_inode_is_fast_symlink(new_inode))) {
+			struct ocfs2_dinode *new_di = (struct ocfs2_dinode *)new_bh->b_data;
+			struct ocfs2_dinode *old_di = (struct ocfs2_dinode *)old_bh->b_data;
+			struct ocfs2_extent_list *el = &new_di->id2.i_list;
+			int inline_size = le16_to_cpu(old_di->i_xattr_inline_size);
+
+			le16_add_cpu(&el->l_count, -(inline_size /
+					sizeof(struct ocfs2_extent_rec)));
+		}
+	}
+
 	ret = ocfs2_create_reflink_node(inode, old_bh,
 					new_inode, new_bh, preserve);
 	if (ret) {
@@ -4216,7 +4238,7 @@
 		goto inode_unlock;
 	}
 
-	if (OCFS2_I(inode)->ip_dyn_features & OCFS2_HAS_XATTR_FL) {
+	if (oi->ip_dyn_features & OCFS2_HAS_XATTR_FL) {
 		ret = ocfs2_reflink_xattrs(inode, old_bh,
 					   new_inode, new_bh,
 					   preserve);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/resize.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/resize.c
@@ -566,6 +566,8 @@
 	ocfs2_commit_trans(osb, handle);
 
 out_free_group_bh:
+	if (ret < 0)
+		ocfs2_remove_from_cache(INODE_CACHE(inode), group_bh);
 	brelse(group_bh);
 
 out_unlock:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/slot_map.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/slot_map.c
@@ -252,16 +252,14 @@
 	int i, ret = -ENOSPC;
 
 	if ((preferred >= 0) && (preferred < si->si_num_slots)) {
-		if (!si->si_slots[preferred].sl_valid ||
-		    !si->si_slots[preferred].sl_node_num) {
+		if (!si->si_slots[preferred].sl_valid) {
 			ret = preferred;
 			goto out;
 		}
 	}
 
 	for(i = 0; i < si->si_num_slots; i++) {
-		if (!si->si_slots[i].sl_valid ||
-		    !si->si_slots[i].sl_node_num) {
+		if (!si->si_slots[i].sl_valid) {
 			ret = i;
 			break;
 		}
@@ -456,30 +454,24 @@
 	spin_lock(&osb->osb_lock);
 	ocfs2_update_slot_info(si);
 
-	if (ocfs2_mount_local(osb))
-		/* use slot 0 directly in local mode */
-		slot = 0;
-	else {
-		/* search for ourselves first and take the slot if it already
-		 * exists. Perhaps we need to mark this in a variable for our
-		 * own journal recovery? Possibly not, though we certainly
-		 * need to warn to the user */
-		slot = __ocfs2_node_num_to_slot(si, osb->node_num);
+	/* search for ourselves first and take the slot if it already
+	 * exists. Perhaps we need to mark this in a variable for our
+	 * own journal recovery? Possibly not, though we certainly
+	 * need to warn to the user */
+	slot = __ocfs2_node_num_to_slot(si, osb->node_num);
+	if (slot < 0) {
+		/* if no slot yet, then just take 1st available
+		 * one. */
+		slot = __ocfs2_find_empty_slot(si, osb->preferred_slot);
 		if (slot < 0) {
-			/* if no slot yet, then just take 1st available
-			 * one. */
-			slot = __ocfs2_find_empty_slot(si, osb->preferred_slot);
-			if (slot < 0) {
-				spin_unlock(&osb->osb_lock);
-				mlog(ML_ERROR, "no free slots available!\n");
-				status = -EINVAL;
-				goto bail;
-			}
-		} else
-			printk(KERN_INFO "ocfs2: Slot %d on device (%s) was "
-			       "already allocated to this node!\n",
-			       slot, osb->dev_str);
-	}
+			spin_unlock(&osb->osb_lock);
+			mlog(ML_ERROR, "no free slots available!\n");
+			status = -EINVAL;
+			goto bail;
+		}
+	} else
+		printk(KERN_INFO "ocfs2: Slot %d on device (%s) was already "
+		       "allocated to this node!\n", slot, osb->dev_str);
 
 	ocfs2_set_slot(si, slot, osb->node_num);
 	osb->slot_num = slot;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/stackglue.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/stackglue.c
@@ -703,6 +703,8 @@
 
 static int __init ocfs2_stack_glue_init(void)
 {
+	int ret;
+
 	strcpy(cluster_stack_name, OCFS2_STACK_PLUGIN_O2CB);
 
 	ocfs2_table_header = register_sysctl_table(ocfs2_root_table);
@@ -712,7 +714,11 @@
 		return -ENOMEM; /* or something. */
 	}
 
-	return ocfs2_sysfs_init();
+	ret = ocfs2_sysfs_init();
+	if (ret)
+		unregister_sysctl_table(ocfs2_table_header);
+
+	return ret;
 }
 
 static void __exit ocfs2_stack_glue_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/suballoc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/suballoc.c
@@ -1251,26 +1251,23 @@
 {
 	struct ocfs2_group_desc *bg = (struct ocfs2_group_desc *) bg_bh->b_data;
 	struct journal_head *jh;
-	int ret = 1;
+	int ret;
 
 	if (ocfs2_test_bit(nr, (unsigned long *)bg->bg_bitmap))
 		return 0;
 
-	if (!buffer_jbd(bg_bh))
+	jh = jbd2_journal_grab_journal_head(bg_bh);
+	if (!jh)
 		return 1;
 
-	jbd_lock_bh_journal_head(bg_bh);
-	if (buffer_jbd(bg_bh)) {
-		jh = bh2jh(bg_bh);
-		spin_lock(&jh->b_state_lock);
-		bg = (struct ocfs2_group_desc *) jh->b_committed_data;
-		if (bg)
-			ret = !ocfs2_test_bit(nr, (unsigned long *)bg->bg_bitmap);
-		else
-			ret = 1;
-		spin_unlock(&jh->b_state_lock);
-	}
-	jbd_unlock_bh_journal_head(bg_bh);
+	spin_lock(&jh->b_state_lock);
+	bg = (struct ocfs2_group_desc *) jh->b_committed_data;
+	if (bg)
+		ret = !ocfs2_test_bit(nr, (unsigned long *)bg->bg_bitmap);
+	else
+		ret = 1;
+	spin_unlock(&jh->b_state_lock);
+	jbd2_journal_put_journal_head(jh);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/super.c
@@ -173,7 +173,6 @@
 	Opt_dir_resv_level,
 	Opt_journal_async_commit,
 	Opt_err_cont,
-	Opt_nocluster,
 	Opt_err,
 };
 
@@ -207,7 +206,6 @@
 	{Opt_dir_resv_level, "dir_resv_level=%u"},
 	{Opt_journal_async_commit, "journal_async_commit"},
 	{Opt_err_cont, "errors=continue"},
-	{Opt_nocluster, "nocluster"},
 	{Opt_err, NULL}
 };
 
@@ -619,13 +617,6 @@
 		goto out;
 	}
 
-	tmp = OCFS2_MOUNT_NOCLUSTER;
-	if ((osb->s_mount_opt & tmp) != (parsed_options.mount_opt & tmp)) {
-		ret = -EINVAL;
-		mlog(ML_ERROR, "Cannot change nocluster option on remount\n");
-		goto out;
-	}
-
 	tmp = OCFS2_MOUNT_HB_LOCAL | OCFS2_MOUNT_HB_GLOBAL |
 		OCFS2_MOUNT_HB_NONE;
 	if ((osb->s_mount_opt & tmp) != (parsed_options.mount_opt & tmp)) {
@@ -866,7 +857,6 @@
 	}
 
 	if (ocfs2_userspace_stack(osb) &&
-	    !(osb->s_mount_opt & OCFS2_MOUNT_NOCLUSTER) &&
 	    strncmp(osb->osb_cluster_stack, mopt->cluster_stack,
 		    OCFS2_STACK_LABEL_LEN)) {
 		mlog(ML_ERROR,
@@ -963,8 +953,10 @@
 	for (type = 0; type < OCFS2_MAXQUOTAS; type++) {
 		if (!sb_has_quota_loaded(sb, type))
 			continue;
-		oinfo = sb_dqinfo(sb, type)->dqi_priv;
-		cancel_delayed_work_sync(&oinfo->dqi_sync_work);
+		if (!sb_has_quota_suspended(sb, type)) {
+			oinfo = sb_dqinfo(sb, type)->dqi_priv;
+			cancel_delayed_work_sync(&oinfo->dqi_sync_work);
+		}
 		inode = igrab(sb->s_dquot.files[type]);
 		/* Turn off quotas. This will remove all dquot structures from
 		 * memory and so they will be automatically synced to global
@@ -990,28 +982,27 @@
 
 	if (!ocfs2_parse_options(sb, data, &parsed_options, 0)) {
 		status = -EINVAL;
-		goto read_super_error;
+		goto out;
 	}
 
 	/* probe for superblock */
 	status = ocfs2_sb_probe(sb, &bh, &sector_size, &stats);
 	if (status < 0) {
 		mlog(ML_ERROR, "superblock probe failed!\n");
-		goto read_super_error;
+		goto out;
 	}
 
 	status = ocfs2_initialize_super(sb, bh, sector_size, &stats);
-	osb = OCFS2_SB(sb);
-	if (status < 0) {
-		mlog_errno(status);
-		goto read_super_error;
-	}
 	brelse(bh);
 	bh = NULL;
+	if (status < 0)
+		goto out;
+
+	osb = OCFS2_SB(sb);
 
 	if (!ocfs2_check_set_options(sb, &parsed_options)) {
 		status = -EINVAL;
-		goto read_super_error;
+		goto out_super;
 	}
 	osb->s_mount_opt = parsed_options.mount_opt;
 	osb->s_atime_quantum = parsed_options.atime_quantum;
@@ -1028,7 +1019,7 @@
 
 	status = ocfs2_verify_userspace_stack(osb, &parsed_options);
 	if (status)
-		goto read_super_error;
+		goto out_super;
 
 	sb->s_magic = OCFS2_SUPER_MAGIC;
 
@@ -1042,7 +1033,7 @@
 			status = -EACCES;
 			mlog(ML_ERROR, "Readonly device detected but readonly "
 			     "mount was not specified.\n");
-			goto read_super_error;
+			goto out_super;
 		}
 
 		/* You should not be able to start a local heartbeat
@@ -1051,7 +1042,7 @@
 			status = -EROFS;
 			mlog(ML_ERROR, "Local heartbeat specified on readonly "
 			     "device.\n");
-			goto read_super_error;
+			goto out_super;
 		}
 
 		status = ocfs2_check_journals_nolocks(osb);
@@ -1060,9 +1051,7 @@
 				mlog(ML_ERROR, "Recovery required on readonly "
 				     "file system, but write access is "
 				     "unavailable.\n");
-			else
-				mlog_errno(status);
-			goto read_super_error;
+			goto out_super;
 		}
 
 		ocfs2_set_ro_flag(osb, 1);
@@ -1078,10 +1067,8 @@
 	}
 
 	status = ocfs2_verify_heartbeat(osb);
-	if (status < 0) {
-		mlog_errno(status);
-		goto read_super_error;
-	}
+	if (status < 0)
+		goto out_super;
 
 	osb->osb_debug_root = debugfs_create_dir(osb->uuid_str,
 						 ocfs2_debugfs_root);
@@ -1095,34 +1082,22 @@
 
 	status = ocfs2_mount_volume(sb);
 	if (status < 0)
-		goto read_super_error;
+		goto out_debugfs;
 
 	if (osb->root_inode)
 		inode = igrab(osb->root_inode);
 
 	if (!inode) {
 		status = -EIO;
-		mlog_errno(status);
-		goto read_super_error;
+		goto out_dismount;
 	}
 
-	root = d_make_root(inode);
-	if (!root) {
-		status = -ENOMEM;
-		mlog_errno(status);
-		goto read_super_error;
-	}
-
-	sb->s_root = root;
-
-	ocfs2_complete_mount_recovery(osb);
-
 	osb->osb_dev_kset = kset_create_and_add(sb->s_id, NULL,
 						&ocfs2_kset->kobj);
 	if (!osb->osb_dev_kset) {
 		status = -ENOMEM;
 		mlog(ML_ERROR, "Unable to create device kset %s.\n", sb->s_id);
-		goto read_super_error;
+		goto out_dismount;
 	}
 
 	/* Create filecheck sysfs related directories/files at
@@ -1131,9 +1106,19 @@
 		status = -ENOMEM;
 		mlog(ML_ERROR, "Unable to create filecheck sysfs directory at "
 			"/sys/fs/ocfs2/%s/filecheck.\n", sb->s_id);
-		goto read_super_error;
+		goto out_dismount;
+	}
+
+	root = d_make_root(inode);
+	if (!root) {
+		status = -ENOMEM;
+		goto out_dismount;
 	}
 
+	sb->s_root = root;
+
+	ocfs2_complete_mount_recovery(osb);
+
 	if (ocfs2_mount_local(osb))
 		snprintf(nodestr, sizeof(nodestr), "local");
 	else
@@ -1145,11 +1130,6 @@
 	       osb->s_mount_opt & OCFS2_MOUNT_DATA_WRITEBACK ? "writeback" :
 	       "ordered");
 
-	if ((osb->s_mount_opt & OCFS2_MOUNT_NOCLUSTER) &&
-	   !(osb->s_feature_incompat & OCFS2_FEATURE_INCOMPAT_LOCAL_MOUNT))
-		printk(KERN_NOTICE "ocfs2: The shared device (%s) is mounted "
-		       "without cluster aware mode.\n", osb->dev_str);
-
 	atomic_set(&osb->vol_state, VOLUME_MOUNTED);
 	wake_up(&osb->osb_mount_event);
 
@@ -1179,17 +1159,22 @@
 
 	return status;
 
-read_super_error:
-	brelse(bh);
-
-	if (status)
-		mlog_errno(status);
+out_dismount:
+	atomic_set(&osb->vol_state, VOLUME_DISABLED);
+	wake_up(&osb->osb_mount_event);
+	ocfs2_free_replay_slots(osb);
+	ocfs2_dismount_volume(sb, 1);
+	goto out;
 
-	if (osb) {
-		atomic_set(&osb->vol_state, VOLUME_DISABLED);
-		wake_up(&osb->osb_mount_event);
-		ocfs2_dismount_volume(sb, 1);
-	}
+out_debugfs:
+	debugfs_remove_recursive(osb->osb_debug_root);
+out_super:
+	ocfs2_release_system_inodes(osb);
+	kfree(osb->recovery_map);
+	ocfs2_delete_osb(osb);
+	kfree(osb);
+out:
+	mlog_errno(status);
 
 	return status;
 }
@@ -1456,9 +1441,6 @@
 		case Opt_journal_async_commit:
 			mopt->mount_opt |= OCFS2_MOUNT_JOURNAL_ASYNC_COMMIT;
 			break;
-		case Opt_nocluster:
-			mopt->mount_opt |= OCFS2_MOUNT_NOCLUSTER;
-			break;
 		default:
 			mlog(ML_ERROR,
 			     "Unrecognized mount option \"%s\" "
@@ -1570,9 +1552,6 @@
 	if (opts & OCFS2_MOUNT_JOURNAL_ASYNC_COMMIT)
 		seq_printf(s, ",journal_async_commit");
 
-	if (opts & OCFS2_MOUNT_NOCLUSTER)
-		seq_printf(s, ",nocluster");
-
 	return 0;
 }
 
@@ -1804,11 +1783,10 @@
 static int ocfs2_mount_volume(struct super_block *sb)
 {
 	int status = 0;
-	int unlock_super = 0;
 	struct ocfs2_super *osb = OCFS2_SB(sb);
 
 	if (ocfs2_is_hard_readonly(osb))
-		goto leave;
+		goto out;
 
 	mutex_init(&osb->obs_trim_fs_mutex);
 
@@ -1818,44 +1796,58 @@
 		if (status == -EBADR && ocfs2_userspace_stack(osb))
 			mlog(ML_ERROR, "couldn't mount because cluster name on"
 			" disk does not match the running cluster name.\n");
-		goto leave;
+		goto out;
 	}
 
 	status = ocfs2_super_lock(osb, 1);
 	if (status < 0) {
 		mlog_errno(status);
-		goto leave;
+		goto out_dlm;
 	}
-	unlock_super = 1;
 
 	/* This will load up the node map and add ourselves to it. */
 	status = ocfs2_find_slot(osb);
 	if (status < 0) {
 		mlog_errno(status);
-		goto leave;
+		goto out_super_lock;
 	}
 
 	/* load all node-local system inodes */
 	status = ocfs2_init_local_system_inodes(osb);
 	if (status < 0) {
 		mlog_errno(status);
-		goto leave;
+		goto out_super_lock;
 	}
 
 	status = ocfs2_check_volume(osb);
 	if (status < 0) {
 		mlog_errno(status);
-		goto leave;
+		goto out_system_inodes;
 	}
 
 	status = ocfs2_truncate_log_init(osb);
-	if (status < 0)
+	if (status < 0) {
 		mlog_errno(status);
+		goto out_check_volume;
+	}
 
-leave:
-	if (unlock_super)
-		ocfs2_super_unlock(osb, 1);
+	ocfs2_super_unlock(osb, 1);
+	return 0;
 
+out_check_volume:
+	ocfs2_free_replay_slots(osb);
+out_system_inodes:
+	if (osb->local_alloc_state == OCFS2_LA_ENABLED)
+		ocfs2_shutdown_local_alloc(osb);
+	ocfs2_release_system_inodes(osb);
+	/* before journal shutdown, we should release slot_info */
+	ocfs2_free_slot_info(osb);
+	ocfs2_journal_shutdown(osb);
+out_super_lock:
+	ocfs2_super_unlock(osb, 1);
+out_dlm:
+	ocfs2_dlm_shutdown(osb, 0);
+out:
 	return status;
 }
 
@@ -1928,8 +1920,7 @@
 	    !ocfs2_is_hard_readonly(osb))
 		hangup_needed = 1;
 
-	if (osb->cconn)
-		ocfs2_dlm_shutdown(osb, hangup_needed);
+	ocfs2_dlm_shutdown(osb, hangup_needed);
 
 	ocfs2_blockcheck_stats_debugfs_remove(&osb->osb_ecc_stats);
 	debugfs_remove_recursive(osb->osb_debug_root);
@@ -2334,6 +2325,7 @@
 			       struct ocfs2_blockcheck_stats *stats)
 {
 	int status = -EAGAIN;
+	u32 blksz_bits;
 
 	if (memcmp(di->i_signature, OCFS2_SUPER_BLOCK_SIGNATURE,
 		   strlen(OCFS2_SUPER_BLOCK_SIGNATURE)) == 0) {
@@ -2348,11 +2340,15 @@
 				goto out;
 		}
 		status = -EINVAL;
-		if ((1 << le32_to_cpu(di->id2.i_super.s_blocksize_bits)) != blksz) {
+		/* Acceptable block sizes are 512 bytes, 1K, 2K and 4K. */
+		blksz_bits = le32_to_cpu(di->id2.i_super.s_blocksize_bits);
+		if (blksz_bits < 9 || blksz_bits > 12) {
+			mlog(ML_ERROR, "found superblock with incorrect block "
+			     "size bits: found %u, should be 9, 10, 11, or 12\n",
+			     blksz_bits);
+		} else if ((1 << blksz_bits) != blksz) {
 			mlog(ML_ERROR, "found superblock with incorrect block "
-			     "size: found %u, should be %u\n",
-			     1 << le32_to_cpu(di->id2.i_super.s_blocksize_bits),
-			       blksz);
+			     "size: found %u, should be %u\n", 1 << blksz_bits, blksz);
 		} else if (le16_to_cpu(di->id2.i_super.s_major_rev_level) !=
 			   OCFS2_MAJOR_REV_LEVEL ||
 			   le16_to_cpu(di->id2.i_super.s_minor_rev_level) !=
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/symlink.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/symlink.c
@@ -64,7 +64,7 @@
 
 	if (status < 0) {
 		mlog_errno(status);
-		return status;
+		goto out;
 	}
 
 	fe = (struct ocfs2_dinode *) bh->b_data;
@@ -75,9 +75,10 @@
 	memcpy(kaddr, link, len + 1);
 	kunmap_atomic(kaddr);
 	SetPageUptodate(page);
+out:
 	unlock_page(page);
 	brelse(bh);
-	return 0;
+	return status;
 }
 
 const struct address_space_operations ocfs2_fast_symlink_aops = {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ocfs2/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ocfs2/xattr.c
@@ -1066,13 +1066,13 @@
 	return i_ret + b_ret;
 }
 
-static int ocfs2_xattr_find_entry(int name_index,
+static int ocfs2_xattr_find_entry(struct inode *inode, int name_index,
 				  const char *name,
 				  struct ocfs2_xattr_search *xs)
 {
 	struct ocfs2_xattr_entry *entry;
 	size_t name_len;
-	int i, cmp = 1;
+	int i, name_offset, cmp = 1;
 
 	if (name == NULL)
 		return -EINVAL;
@@ -1080,13 +1080,22 @@
 	name_len = strlen(name);
 	entry = xs->here;
 	for (i = 0; i < le16_to_cpu(xs->header->xh_count); i++) {
+		if ((void *)entry >= xs->end) {
+			ocfs2_error(inode->i_sb, "corrupted xattr entries");
+			return -EFSCORRUPTED;
+		}
 		cmp = name_index - ocfs2_xattr_get_type(entry);
 		if (!cmp)
 			cmp = name_len - entry->xe_name_len;
-		if (!cmp)
-			cmp = memcmp(name, (xs->base +
-				     le16_to_cpu(entry->xe_name_offset)),
-				     name_len);
+		if (!cmp) {
+			name_offset = le16_to_cpu(entry->xe_name_offset);
+			if ((xs->base + name_offset + name_len) > xs->end) {
+				ocfs2_error(inode->i_sb,
+					    "corrupted xattr entries");
+				return -EFSCORRUPTED;
+			}
+			cmp = memcmp(name, (xs->base + name_offset), name_len);
+		}
 		if (cmp == 0)
 			break;
 		entry += 1;
@@ -1170,7 +1179,7 @@
 	xs->base = (void *)xs->header;
 	xs->here = xs->header->xh_entries;
 
-	ret = ocfs2_xattr_find_entry(name_index, name, xs);
+	ret = ocfs2_xattr_find_entry(inode, name_index, name, xs);
 	if (ret)
 		return ret;
 	size = le64_to_cpu(xs->here->xe_value_size);
@@ -2031,8 +2040,7 @@
 				rc = 0;
 			ocfs2_xa_cleanup_value_truncate(loc, "removing",
 							orig_clusters);
-			if (rc)
-				goto out;
+			goto out;
 		}
 	}
 
@@ -2702,7 +2710,7 @@
 
 	/* Find the named attribute. */
 	if (oi->ip_dyn_features & OCFS2_INLINE_XATTR_FL) {
-		ret = ocfs2_xattr_find_entry(name_index, name, xs);
+		ret = ocfs2_xattr_find_entry(inode, name_index, name, xs);
 		if (ret && ret != -ENODATA)
 			return ret;
 		xs->not_found = ret;
@@ -2837,7 +2845,7 @@
 		xs->end = (void *)(blk_bh->b_data) + blk_bh->b_size;
 		xs->here = xs->header->xh_entries;
 
-		ret = ocfs2_xattr_find_entry(name_index, name, xs);
+		ret = ocfs2_xattr_find_entry(inode, name_index, name, xs);
 	} else
 		ret = ocfs2_xattr_index_block_find(inode, blk_bh,
 						   name_index,
@@ -6515,16 +6523,7 @@
 	}
 
 	new_oi = OCFS2_I(args->new_inode);
-	/*
-	 * Adjust extent record count to reserve space for extended attribute.
-	 * Inline data count had been adjusted in ocfs2_duplicate_inline_data().
-	 */
-	if (!(new_oi->ip_dyn_features & OCFS2_INLINE_DATA_FL) &&
-	    !(ocfs2_inode_is_fast_symlink(args->new_inode))) {
-		struct ocfs2_extent_list *el = &new_di->id2.i_list;
-		le16_add_cpu(&el->l_count, -(inline_size /
-					sizeof(struct ocfs2_extent_rec)));
-	}
+
 	spin_lock(&new_oi->ip_lock);
 	new_oi->ip_dyn_features |= OCFS2_HAS_XATTR_FL | OCFS2_INLINE_XATTR_FL;
 	new_di->i_dyn_features = cpu_to_le16(new_oi->ip_dyn_features);
@@ -7259,9 +7258,21 @@
 static int ocfs2_initxattrs(struct inode *inode, const struct xattr *xattr_array,
 		     void *fs_info)
 {
+	struct ocfs2_security_xattr_info *si = fs_info;
 	const struct xattr *xattr;
 	int err = 0;
 
+	if (si) {
+		si->value = kmemdup(xattr_array->value, xattr_array->value_len,
+				    GFP_KERNEL);
+		if (!si->value)
+			return -ENOMEM;
+
+		si->name = xattr_array->name;
+		si->value_len = xattr_array->value_len;
+		return 0;
+	}
+
 	for (xattr = xattr_array; xattr->name != NULL; xattr++) {
 		err = ocfs2_xattr_set(inode, OCFS2_XATTR_INDEX_SECURITY,
 				      xattr->name, xattr->value,
@@ -7277,13 +7288,23 @@
 			    const struct qstr *qstr,
 			    struct ocfs2_security_xattr_info *si)
 {
+	int ret;
+
 	/* check whether ocfs2 support feature xattr */
 	if (!ocfs2_supports_xattr(OCFS2_SB(dir->i_sb)))
 		return -EOPNOTSUPP;
-	if (si)
-		return security_old_inode_init_security(inode, dir, qstr,
-							&si->name, &si->value,
-							&si->value_len);
+	if (si) {
+		ret = security_inode_init_security(inode, dir, qstr,
+						   &ocfs2_initxattrs, si);
+		/*
+		 * security_inode_init_security() does not return -EOPNOTSUPP,
+		 * we have to check the xattr ourselves.
+		 */
+		if (!ret && !si->name)
+			si->enable = 0;
+
+		return ret;
+	}
 
 	return security_inode_init_security(inode, dir, qstr,
 					    &ocfs2_initxattrs, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/open.c
+++ linux-xilinx-zynqmp-5.15.0/fs/open.c
@@ -32,6 +32,7 @@
 #include <linux/ima.h>
 #include <linux/dnotify.h>
 #include <linux/compat.h>
+#include <linux/mnt_idmapping.h>
 
 #include "internal.h"
 
@@ -53,7 +54,7 @@
 	}
 
 	/* Remove suid, sgid, and file capabilities on truncate too */
-	ret = dentry_needs_remove_privs(dentry);
+	ret = dentry_needs_remove_privs(mnt_userns, dentry);
 	if (ret < 0)
 		return ret;
 	if (ret)
@@ -65,6 +66,7 @@
 	inode_unlock(dentry->d_inode);
 	return ret;
 }
+EXPORT_SYMBOL_GPL(do_truncate);
 
 long vfs_truncate(const struct path *path, loff_t length)
 {
@@ -198,13 +200,13 @@
 	return error;
 }
 
-SYSCALL_DEFINE2(ftruncate, unsigned int, fd, unsigned long, length)
+SYSCALL_DEFINE2(ftruncate, unsigned int, fd, off_t, length)
 {
 	return do_sys_ftruncate(fd, length, 1);
 }
 
 #ifdef CONFIG_COMPAT
-COMPAT_SYSCALL_DEFINE2(ftruncate, unsigned int, fd, compat_ulong_t, length)
+COMPAT_SYSCALL_DEFINE2(ftruncate, unsigned int, fd, compat_off_t, length)
 {
 	return do_sys_ftruncate(fd, length, 1);
 }
@@ -640,7 +642,7 @@
 
 int chown_common(const struct path *path, uid_t user, gid_t group)
 {
-	struct user_namespace *mnt_userns;
+	struct user_namespace *mnt_userns, *fs_userns;
 	struct inode *inode = path->dentry->d_inode;
 	struct inode *delegated_inode = NULL;
 	int error;
@@ -652,8 +654,9 @@
 	gid = make_kgid(current_user_ns(), group);
 
 	mnt_userns = mnt_user_ns(path->mnt);
-	uid = kuid_from_mnt(mnt_userns, uid);
-	gid = kgid_from_mnt(mnt_userns, gid);
+	fs_userns = i_user_ns(inode);
+	uid = mapped_kuid_user(mnt_userns, fs_userns, uid);
+	gid = mapped_kgid_user(mnt_userns, fs_userns, gid);
 
 retry_deleg:
 	newattrs.ia_valid =  ATTR_CTIME;
@@ -669,10 +672,10 @@
 		newattrs.ia_valid |= ATTR_GID;
 		newattrs.ia_gid = gid;
 	}
-	if (!S_ISDIR(inode->i_mode))
-		newattrs.ia_valid |=
-			ATTR_KILL_SUID | ATTR_KILL_SGID | ATTR_KILL_PRIV;
 	inode_lock(inode);
+	if (!S_ISDIR(inode->i_mode))
+		newattrs.ia_valid |= ATTR_KILL_SUID | ATTR_KILL_PRIV |
+				     setattr_should_drop_sgid(mnt_userns, inode);
 	error = security_path_chown(path, uid, gid);
 	if (!error)
 		error = notify_change(mnt_userns, path->dentry, &newattrs,
@@ -784,7 +787,9 @@
 		return 0;
 	}
 
-	if (f->f_mode & FMODE_WRITE && !special_file(inode->i_mode)) {
+	if ((f->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ) {
+		i_readcount_inc(inode);
+	} else if (f->f_mode & FMODE_WRITE && !special_file(inode->i_mode)) {
 		error = get_write_access(inode);
 		if (unlikely(error))
 			goto cleanup_file;
@@ -824,8 +829,6 @@
 			goto cleanup_all;
 	}
 	f->f_mode |= FMODE_OPENED;
-	if ((f->f_mode & (FMODE_READ | FMODE_WRITE)) == FMODE_READ)
-		i_readcount_inc(inode);
 	if ((f->f_mode & FMODE_READ) &&
 	     likely(f->f_op->read || f->f_op->read_iter))
 		f->f_mode |= FMODE_CAN_READ;
@@ -856,8 +859,20 @@
 		 * of THPs into the page cache will fail.
 		 */
 		smp_mb();
-		if (filemap_nr_thps(inode->i_mapping))
-			truncate_pagecache(inode, 0);
+		if (filemap_nr_thps(inode->i_mapping)) {
+			struct address_space *mapping = inode->i_mapping;
+
+			filemap_invalidate_lock(inode->i_mapping);
+			/*
+			 * unmap_mapping_range just need to be called once
+			 * here, because the private pages is not need to be
+			 * unmapped mapping (e.g. data segment of dynamic
+			 * shared libraries here).
+			 */
+			unmap_mapping_range(mapping, 0, 0, 0);
+			truncate_inode_pages(mapping, 0);
+			filemap_invalidate_unlock(inode->i_mapping);
+		}
 	}
 
 	return 0;
@@ -866,10 +881,7 @@
 	if (WARN_ON_ONCE(error > 0))
 		error = -EINVAL;
 	fops_put(f->f_op);
-	if (f->f_mode & FMODE_WRITER) {
-		put_write_access(inode);
-		__mnt_drop_write(f->f_path.mnt);
-	}
+	put_file_access(f);
 cleanup_file:
 	path_put(&f->f_path);
 	f->f_path.mnt = NULL;
@@ -968,6 +980,48 @@
 }
 EXPORT_SYMBOL(dentry_open);
 
+/**
+ * dentry_create - Create and open a file
+ * @path: path to create
+ * @flags: O_ flags
+ * @mode: mode bits for new file
+ * @cred: credentials to use
+ *
+ * Caller must hold the parent directory's lock, and have prepared
+ * a negative dentry, placed in @path->dentry, for the new file.
+ *
+ * Caller sets @path->mnt to the vfsmount of the filesystem where
+ * the new file is to be created. The parent directory and the
+ * negative dentry must reside on the same filesystem instance.
+ *
+ * On success, returns a "struct file *". Otherwise a ERR_PTR
+ * is returned.
+ */
+struct file *dentry_create(const struct path *path, int flags, umode_t mode,
+			   const struct cred *cred)
+{
+	struct file *f;
+	int error;
+
+	validate_creds(cred);
+	f = alloc_empty_file(flags, cred);
+	if (IS_ERR(f))
+		return f;
+
+	error = vfs_create(mnt_user_ns(path->mnt),
+			   d_inode(path->dentry->d_parent),
+			   path->dentry, mode, true);
+	if (!error)
+		error = vfs_open(path, f);
+
+	if (unlikely(error)) {
+		fput(f);
+		return ERR_PTR(error);
+	}
+	return f;
+}
+EXPORT_SYMBOL(dentry_create);
+
 struct file *open_with_fake_path(const struct path *path, int flags,
 				struct inode *inode, const struct cred *cred)
 {
@@ -1115,7 +1169,7 @@
 		lookup_flags |= LOOKUP_IN_ROOT;
 	if (how->resolve & RESOLVE_CACHED) {
 		/* Don't bother even trying for create/truncate/tmpfile open */
-		if (flags & (O_TRUNC | O_CREAT | O_TMPFILE))
+		if (flags & (O_TRUNC | O_CREAT | __O_TMPFILE))
 			return -EAGAIN;
 		lookup_flags |= LOOKUP_CACHED;
 	}
@@ -1243,6 +1297,8 @@
 
 	if (unlikely(usize < OPEN_HOW_SIZE_VER0))
 		return -EINVAL;
+	if (unlikely(usize > PAGE_SIZE))
+		return -E2BIG;
 
 	err = copy_struct_from_user(&tmp, sizeof(tmp), how, usize);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/openpromfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/openpromfs/inode.c
@@ -355,10 +355,10 @@
 	return inode;
 }
 
-static int openprom_remount(struct super_block *sb, int *flags, char *data)
+static int openpromfs_reconfigure(struct fs_context *fc)
 {
-	sync_filesystem(sb);
-	*flags |= SB_NOATIME;
+	sync_filesystem(fc->root->d_sb);
+	fc->sb_flags |= SB_NOATIME;
 	return 0;
 }
 
@@ -366,7 +366,6 @@
 	.alloc_inode	= openprom_alloc_inode,
 	.free_inode	= openprom_free_inode,
 	.statfs		= simple_statfs,
-	.remount_fs	= openprom_remount,
 };
 
 static int openprom_fill_super(struct super_block *s, struct fs_context *fc)
@@ -416,6 +415,7 @@
 
 static const struct fs_context_operations openpromfs_context_ops = {
 	.get_tree	= openpromfs_get_tree,
+	.reconfigure	= openpromfs_reconfigure,
 };
 
 static int openpromfs_init_fs_context(struct fs_context *fc)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/orangefs/dcache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/orangefs/dcache.c
@@ -26,8 +26,10 @@
 	gossip_debug(GOSSIP_DCACHE_DEBUG, "%s: attempting lookup.\n", __func__);
 
 	new_op = op_alloc(ORANGEFS_VFS_OP_LOOKUP);
-	if (!new_op)
+	if (!new_op) {
+		ret = -ENOMEM;
 		goto out_put_parent;
+	}
 
 	new_op->upcall.req.lookup.sym_follow = ORANGEFS_LOOKUP_LINK_NO_FOLLOW;
 	new_op->upcall.req.lookup.parent_refn = parent->refn;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/orangefs/orangefs-bufmap.c
+++ linux-xilinx-zynqmp-5.15.0/fs/orangefs/orangefs-bufmap.c
@@ -176,7 +176,7 @@
 {
 	kfree(bufmap->page_array);
 	kfree(bufmap->desc_array);
-	kfree(bufmap->buffer_index_array);
+	bitmap_free(bufmap->buffer_index_array);
 	kfree(bufmap);
 }
 
@@ -226,8 +226,7 @@
 	bufmap->desc_size = user_desc->size;
 	bufmap->desc_shift = ilog2(bufmap->desc_size);
 
-	bufmap->buffer_index_array =
-		kzalloc(DIV_ROUND_UP(bufmap->desc_count, BITS_PER_LONG), GFP_KERNEL);
+	bufmap->buffer_index_array = bitmap_zalloc(bufmap->desc_count, GFP_KERNEL);
 	if (!bufmap->buffer_index_array)
 		goto out_free_bufmap;
 
@@ -250,7 +249,7 @@
 out_free_desc_array:
 	kfree(bufmap->desc_array);
 out_free_index_array:
-	kfree(bufmap->buffer_index_array);
+	bitmap_free(bufmap->buffer_index_array);
 out_free_bufmap:
 	kfree(bufmap);
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/orangefs/orangefs-debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/orangefs/orangefs-debugfs.c
@@ -194,15 +194,10 @@
  */
 static void orangefs_kernel_debug_init(void)
 {
-	int rc = -ENOMEM;
-	char *k_buffer = NULL;
+	static char k_buffer[ORANGEFS_MAX_DEBUG_STRING_LEN] = { };
 
 	gossip_debug(GOSSIP_DEBUGFS_DEBUG, "%s: start\n", __func__);
 
-	k_buffer = kzalloc(ORANGEFS_MAX_DEBUG_STRING_LEN, GFP_KERNEL);
-	if (!k_buffer)
-		goto out;
-
 	if (strlen(kernel_debug_string) + 1 < ORANGEFS_MAX_DEBUG_STRING_LEN) {
 		strcpy(k_buffer, kernel_debug_string);
 		strcat(k_buffer, "\n");
@@ -213,15 +208,14 @@
 
 	debugfs_create_file(ORANGEFS_KMOD_DEBUG_FILE, 0444, debug_dir, k_buffer,
 			    &kernel_debug_fops);
-
-out:
-	gossip_debug(GOSSIP_DEBUGFS_DEBUG, "%s: rc:%d:\n", __func__, rc);
 }
 
 
 void orangefs_debugfs_cleanup(void)
 {
 	debugfs_remove_recursive(debug_dir);
+	kfree(debug_help_string);
+	debug_help_string = NULL;
 }
 
 /* open ORANGEFS_KMOD_DEBUG_HELP_FILE */
@@ -297,18 +291,13 @@
 /*
  * initialize the client-debug file.
  */
-static int orangefs_client_debug_init(void)
+static void orangefs_client_debug_init(void)
 {
 
-	int rc = -ENOMEM;
-	char *c_buffer = NULL;
+	static char c_buffer[ORANGEFS_MAX_DEBUG_STRING_LEN] = { };
 
 	gossip_debug(GOSSIP_DEBUGFS_DEBUG, "%s: start\n", __func__);
 
-	c_buffer = kzalloc(ORANGEFS_MAX_DEBUG_STRING_LEN, GFP_KERNEL);
-	if (!c_buffer)
-		goto out;
-
 	if (strlen(client_debug_string) + 1 < ORANGEFS_MAX_DEBUG_STRING_LEN) {
 		strcpy(c_buffer, client_debug_string);
 		strcat(c_buffer, "\n");
@@ -322,13 +311,6 @@
 						  debug_dir,
 						  c_buffer,
 						  &kernel_debug_fops);
-
-	rc = 0;
-
-out:
-
-	gossip_debug(GOSSIP_DEBUGFS_DEBUG, "%s: rc:%d:\n", __func__, rc);
-	return rc;
 }
 
 /* open ORANGEFS_KMOD_DEBUG_FILE or ORANGEFS_CLIENT_DEBUG_FILE.*/
@@ -411,9 +393,9 @@
 	 * Thwart users who try to jamb a ridiculous number
 	 * of bytes into the debug file...
 	 */
-	if (count > ORANGEFS_MAX_DEBUG_STRING_LEN + 1) {
+	if (count > ORANGEFS_MAX_DEBUG_STRING_LEN) {
 		silly = count;
-		count = ORANGEFS_MAX_DEBUG_STRING_LEN + 1;
+		count = ORANGEFS_MAX_DEBUG_STRING_LEN;
 	}
 
 	buf = kzalloc(ORANGEFS_MAX_DEBUG_STRING_LEN, GFP_KERNEL);
@@ -671,6 +653,7 @@
 		memset(debug_help_string, 0, DEBUG_HELP_STRING_SIZE);
 		strlcat(debug_help_string, new, string_size);
 		mutex_unlock(&orangefs_help_file_lock);
+		kfree(new);
 	}
 
 	rc = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/orangefs/orangefs-mod.c
+++ linux-xilinx-zynqmp-5.15.0/fs/orangefs/orangefs-mod.c
@@ -141,7 +141,7 @@
 		gossip_err("%s: could not initialize device subsystem %d!\n",
 			   __func__,
 			   ret);
-		goto cleanup_device;
+		goto cleanup_sysfs;
 	}
 
 	ret = register_filesystem(&orangefs_fs_type);
@@ -152,11 +152,11 @@
 		goto out;
 	}
 
-	orangefs_sysfs_exit();
-
-cleanup_device:
 	orangefs_dev_cleanup();
 
+cleanup_sysfs:
+	orangefs_sysfs_exit();
+
 sysfs_init_failed:
 	orangefs_debugfs_cleanup();
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/orangefs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/orangefs/super.c
@@ -200,7 +200,8 @@
 		     (long)new_op->downcall.resp.statfs.files_avail);
 
 	buf->f_type = sb->s_magic;
-	memcpy(&buf->f_fsid, &ORANGEFS_SB(sb)->fs_id, sizeof(buf->f_fsid));
+	buf->f_fsid.val[0] = ORANGEFS_SB(sb)->fs_id;
+	buf->f_fsid.val[1] = ORANGEFS_SB(sb)->id;
 	buf->f_bsize = new_op->downcall.resp.statfs.block_size;
 	buf->f_namelen = ORANGEFS_NAME_MAX;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/copy_up.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/copy_up.c
@@ -117,7 +117,7 @@
 			goto retry;
 		}
 
-		error = vfs_setxattr(&init_user_ns, new, name, value, size, 0);
+		error = ovl_do_setxattr(OVL_FS(sb), new, name, value, size, 0);
 		if (error) {
 			if (error != -EOPNOTSUPP || ovl_must_copy_xattr(name))
 				break;
@@ -140,12 +140,14 @@
 	int err;
 
 	err = ovl_real_fileattr_get(old, &oldfa);
-	if (err)
-		return err;
-
-	err = ovl_real_fileattr_get(new, &newfa);
-	if (err)
+	if (err) {
+		/* Ntfs-3g returns -EINVAL for "no fileattr support" */
+		if (err == -ENOTTY || err == -EINVAL)
+			return 0;
+		pr_warn("failed to retrieve lower fileattr (%pd2, err=%i)\n",
+			old->dentry, err);
 		return err;
+	}
 
 	/*
 	 * We cannot set immutable and append-only flags on upper inode,
@@ -155,10 +157,31 @@
 	 */
 	if (oldfa.flags & OVL_PROT_FS_FLAGS_MASK) {
 		err = ovl_set_protattr(inode, new->dentry, &oldfa);
-		if (err)
+		if (err == -EPERM)
+			pr_warn_once("copying fileattr: no xattr on upper\n");
+		else if (err)
 			return err;
 	}
 
+	/* Don't bother copying flags if none are set */
+	if (!(oldfa.flags & OVL_COPY_FS_FLAGS_MASK))
+		return 0;
+
+	err = ovl_real_fileattr_get(new, &newfa);
+	if (err) {
+		/*
+		 * Returning an error if upper doesn't support fileattr will
+		 * result in a regression, so revert to the old behavior.
+		 */
+		if (err == -ENOTTY || err == -EINVAL) {
+			pr_warn_once("copying fileattr: no support on upper\n");
+			return 0;
+		}
+		pr_warn("failed to retrieve upper fileattr (%pd2, err=%i)\n",
+			new->dentry, err);
+		return err;
+	}
+
 	BUILD_BUG_ON(OVL_COPY_FS_FLAGS_MASK & ~FS_COMMON_FL);
 	newfa.flags &= ~OVL_COPY_FS_FLAGS_MASK;
 	newfa.flags |= (oldfa.flags & OVL_COPY_FS_FLAGS_MASK);
@@ -283,7 +306,7 @@
 {
 	struct iattr attr = {
 		.ia_valid =
-		     ATTR_ATIME | ATTR_MTIME | ATTR_ATIME_SET | ATTR_MTIME_SET,
+		     ATTR_ATIME | ATTR_MTIME | ATTR_ATIME_SET | ATTR_MTIME_SET | ATTR_CTIME,
 		.ia_atime = stat->atime,
 		.ia_mtime = stat->mtime,
 	};
@@ -410,7 +433,7 @@
 	if (IS_ERR(fh))
 		return PTR_ERR(fh);
 
-	err = ovl_do_setxattr(ofs, index, OVL_XATTR_UPPER, fh->buf, fh->fb.len);
+	err = ovl_setxattr(ofs, index, OVL_XATTR_UPPER, fh->buf, fh->fb.len);
 
 	kfree(fh);
 	return err;
@@ -451,7 +474,7 @@
 	if (err)
 		return err;
 
-	temp = ovl_create_temp(indexdir, OVL_CATTR(S_IFDIR | 0));
+	temp = ovl_create_temp(ofs, indexdir, OVL_CATTR(S_IFDIR | 0));
 	err = PTR_ERR(temp);
 	if (IS_ERR(temp))
 		goto free_name;
@@ -464,12 +487,12 @@
 	if (IS_ERR(index)) {
 		err = PTR_ERR(index);
 	} else {
-		err = ovl_do_rename(dir, temp, dir, index, 0);
+		err = ovl_do_rename(ofs, dir, temp, dir, index, 0);
 		dput(index);
 	}
 out:
 	if (err)
-		ovl_cleanup(dir, temp);
+		ovl_cleanup(ofs, dir, temp);
 	dput(temp);
 free_name:
 	kfree(name.name);
@@ -496,6 +519,7 @@
 	int err;
 	struct dentry *upper;
 	struct dentry *upperdir = ovl_dentry_upper(c->parent);
+	struct ovl_fs *ofs = OVL_FS(c->dentry->d_sb);
 	struct inode *udir = d_inode(upperdir);
 
 	/* Mark parent "impure" because it may now contain non-pure upper */
@@ -512,14 +536,15 @@
 			       c->dentry->d_name.len);
 	err = PTR_ERR(upper);
 	if (!IS_ERR(upper)) {
-		err = ovl_do_link(ovl_dentry_upper(c->dentry), udir, upper);
-		dput(upper);
+		err = ovl_do_link(ofs, ovl_dentry_upper(c->dentry), udir, upper);
 
 		if (!err) {
 			/* Restore timestamps on parent (best effort) */
 			ovl_set_timestamps(upperdir, &c->pstat);
 			ovl_dentry_set_upper_alias(c->dentry);
+			ovl_dentry_update_reval(c->dentry, upper);
 		}
+		dput(upper);
 	}
 	inode_unlock(udir);
 	if (err)
@@ -559,7 +584,8 @@
 	if (err)
 		return err;
 
-	if (inode->i_flags & OVL_COPY_I_FLAGS_MASK) {
+	if (inode->i_flags & OVL_COPY_I_FLAGS_MASK &&
+	    (S_ISREG(c->stat.mode) || S_ISDIR(c->stat.mode))) {
 		/*
 		 * Copy the fileattr inode flags that are the source of already
 		 * copied i_flags
@@ -633,6 +659,7 @@
  */
 static int ovl_copy_up_workdir(struct ovl_copy_up_ctx *c)
 {
+	struct ovl_fs *ofs = OVL_FS(c->dentry->d_sb);
 	struct inode *inode;
 	struct inode *udir = d_inode(c->destdir), *wdir = d_inode(c->workdir);
 	struct dentry *temp, *upper;
@@ -654,7 +681,7 @@
 	if (err)
 		goto unlock;
 
-	temp = ovl_create_temp(c->workdir, &cattr);
+	temp = ovl_create_temp(ofs, c->workdir, &cattr);
 	ovl_revert_cu_creds(&cc);
 
 	err = PTR_ERR(temp);
@@ -676,7 +703,7 @@
 	if (IS_ERR(upper))
 		goto cleanup;
 
-	err = ovl_do_rename(wdir, temp, udir, upper, 0);
+	err = ovl_do_rename(ofs, wdir, temp, udir, upper, 0);
 	dput(upper);
 	if (err)
 		goto cleanup;
@@ -693,7 +720,7 @@
 	return err;
 
 cleanup:
-	ovl_cleanup(wdir, temp);
+	ovl_cleanup(ofs, wdir, temp);
 	dput(temp);
 	goto unlock;
 }
@@ -701,6 +728,7 @@
 /* Copyup using O_TMPFILE which does not require cross dir locking */
 static int ovl_copy_up_tmpfile(struct ovl_copy_up_ctx *c)
 {
+	struct ovl_fs *ofs = OVL_FS(c->dentry->d_sb);
 	struct inode *udir = d_inode(c->destdir);
 	struct dentry *temp, *upper;
 	struct ovl_cu_creds cc;
@@ -710,7 +738,7 @@
 	if (err)
 		return err;
 
-	temp = ovl_do_tmpfile(c->workdir, c->stat.mode);
+	temp = ovl_do_tmpfile(ofs, c->workdir, c->stat.mode);
 	ovl_revert_cu_creds(&cc);
 
 	if (IS_ERR(temp))
@@ -725,7 +753,7 @@
 	upper = lookup_one_len(c->destname.name, c->destdir, c->destname.len);
 	err = PTR_ERR(upper);
 	if (!IS_ERR(upper)) {
-		err = ovl_do_link(temp, udir, upper);
+		err = ovl_do_link(ofs, temp, udir, upper);
 		dput(upper);
 	}
 	inode_unlock(udir);
@@ -817,6 +845,7 @@
 		inode_unlock(udir);
 
 		ovl_dentry_set_upper_alias(c->dentry);
+		ovl_dentry_update_reval(c->dentry, ovl_dentry_upper(c->dentry));
 	}
 
 out:
@@ -842,12 +871,13 @@
 	return true;
 }
 
-static ssize_t ovl_getxattr(struct dentry *dentry, char *name, char **value)
+static ssize_t ovl_getxattr_value(struct ovl_fs *ofs, struct dentry *dentry,
+				  char *name, char **value)
 {
 	ssize_t res;
 	char *buf;
 
-	res = vfs_getxattr(&init_user_ns, dentry, name, NULL, 0);
+	res = ovl_do_getxattr(ofs, dentry, name, NULL, 0);
 	if (res == -ENODATA || res == -EOPNOTSUPP)
 		res = 0;
 
@@ -856,7 +886,7 @@
 		if (!buf)
 			return -ENOMEM;
 
-		res = vfs_getxattr(&init_user_ns, dentry, name, buf, res);
+		res = ovl_do_getxattr(ofs, dentry, name, buf, res);
 		if (res < 0)
 			kfree(buf);
 		else
@@ -883,8 +913,8 @@
 		return -EIO;
 
 	if (c->stat.size) {
-		err = cap_size = ovl_getxattr(upperpath.dentry, XATTR_NAME_CAPS,
-					      &capability);
+		err = cap_size = ovl_getxattr_value(ofs, upperpath.dentry,
+						    XATTR_NAME_CAPS, &capability);
 		if (cap_size < 0)
 			goto out;
 	}
@@ -898,14 +928,14 @@
 	 * don't want that to happen for normal copy-up operation.
 	 */
 	if (capability) {
-		err = vfs_setxattr(&init_user_ns, upperpath.dentry,
-				   XATTR_NAME_CAPS, capability, cap_size, 0);
+		err = ovl_do_setxattr(ofs, upperpath.dentry, XATTR_NAME_CAPS,
+				      capability, cap_size, 0);
 		if (err)
 			goto out_free;
 	}
 
 
-	err = ovl_do_removexattr(ofs, upperpath.dentry, OVL_XATTR_METACOPY);
+	err = ovl_removexattr(ofs, upperpath.dentry, OVL_XATTR_METACOPY);
 	if (err)
 		goto out_free;
 
@@ -937,6 +967,10 @@
 	if (err)
 		return err;
 
+	if (!kuid_has_mapping(current_user_ns(), ctx.stat.uid) ||
+	    !kgid_has_mapping(current_user_ns(), ctx.stat.gid))
+		return -EOVERFLOW;
+
 	ctx.metacopy = ovl_need_meta_copy_up(dentry, ctx.stat.mode, flags);
 
 	if (parent) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/dir.c
@@ -23,15 +23,15 @@
 
 static int ovl_set_redirect(struct dentry *dentry, bool samedir);
 
-int ovl_cleanup(struct inode *wdir, struct dentry *wdentry)
+int ovl_cleanup(struct ovl_fs *ofs, struct inode *wdir, struct dentry *wdentry)
 {
 	int err;
 
 	dget(wdentry);
 	if (d_is_dir(wdentry))
-		err = ovl_do_rmdir(wdir, wdentry);
+		err = ovl_do_rmdir(ofs, wdir, wdentry);
 	else
-		err = ovl_do_unlink(wdir, wdentry);
+		err = ovl_do_unlink(ofs, wdir, wdentry);
 	dput(wdentry);
 
 	if (err) {
@@ -42,7 +42,7 @@
 	return err;
 }
 
-struct dentry *ovl_lookup_temp(struct dentry *workdir)
+struct dentry *ovl_lookup_temp(struct ovl_fs *ofs, struct dentry *workdir)
 {
 	struct dentry *temp;
 	char name[20];
@@ -70,11 +70,11 @@
 	struct inode *wdir = workdir->d_inode;
 
 	if (!ofs->whiteout) {
-		whiteout = ovl_lookup_temp(workdir);
+		whiteout = ovl_lookup_temp(ofs, workdir);
 		if (IS_ERR(whiteout))
 			goto out;
 
-		err = ovl_do_whiteout(wdir, whiteout);
+		err = ovl_do_whiteout(ofs, wdir, whiteout);
 		if (err) {
 			dput(whiteout);
 			whiteout = ERR_PTR(err);
@@ -84,11 +84,11 @@
 	}
 
 	if (ofs->share_whiteout) {
-		whiteout = ovl_lookup_temp(workdir);
+		whiteout = ovl_lookup_temp(ofs, workdir);
 		if (IS_ERR(whiteout))
 			goto out;
 
-		err = ovl_do_link(ofs->whiteout, wdir, whiteout);
+		err = ovl_do_link(ofs, ofs->whiteout, wdir, whiteout);
 		if (!err)
 			goto out;
 
@@ -122,28 +122,28 @@
 	if (d_is_dir(dentry))
 		flags = RENAME_EXCHANGE;
 
-	err = ovl_do_rename(wdir, whiteout, dir, dentry, flags);
+	err = ovl_do_rename(ofs, wdir, whiteout, dir, dentry, flags);
 	if (err)
 		goto kill_whiteout;
 	if (flags)
-		ovl_cleanup(wdir, dentry);
+		ovl_cleanup(ofs, wdir, dentry);
 
 out:
 	dput(whiteout);
 	return err;
 
 kill_whiteout:
-	ovl_cleanup(wdir, whiteout);
+	ovl_cleanup(ofs, wdir, whiteout);
 	goto out;
 }
 
-static int ovl_mkdir_real(struct inode *dir, struct dentry **newdentry,
-			  umode_t mode)
+int ovl_mkdir_real(struct ovl_fs *ofs, struct inode *dir,
+		   struct dentry **newdentry, umode_t mode)
 {
 	int err;
 	struct dentry *d, *dentry = *newdentry;
 
-	err = ovl_do_mkdir(dir, dentry, mode);
+	err = ovl_do_mkdir(ofs, dir, dentry, mode);
 	if (err)
 		return err;
 
@@ -168,8 +168,8 @@
 	return 0;
 }
 
-struct dentry *ovl_create_real(struct inode *dir, struct dentry *newdentry,
-			       struct ovl_cattr *attr)
+struct dentry *ovl_create_real(struct ovl_fs *ofs, struct inode *dir,
+			       struct dentry *newdentry, struct ovl_cattr *attr)
 {
 	int err;
 
@@ -181,28 +181,28 @@
 		goto out;
 
 	if (attr->hardlink) {
-		err = ovl_do_link(attr->hardlink, dir, newdentry);
+		err = ovl_do_link(ofs, attr->hardlink, dir, newdentry);
 	} else {
 		switch (attr->mode & S_IFMT) {
 		case S_IFREG:
-			err = ovl_do_create(dir, newdentry, attr->mode);
+			err = ovl_do_create(ofs, dir, newdentry, attr->mode);
 			break;
 
 		case S_IFDIR:
 			/* mkdir is special... */
-			err =  ovl_mkdir_real(dir, &newdentry, attr->mode);
+			err =  ovl_mkdir_real(ofs, dir, &newdentry, attr->mode);
 			break;
 
 		case S_IFCHR:
 		case S_IFBLK:
 		case S_IFIFO:
 		case S_IFSOCK:
-			err = ovl_do_mknod(dir, newdentry, attr->mode,
+			err = ovl_do_mknod(ofs, dir, newdentry, attr->mode,
 					   attr->rdev);
 			break;
 
 		case S_IFLNK:
-			err = ovl_do_symlink(dir, newdentry, attr->link);
+			err = ovl_do_symlink(ofs, dir, newdentry, attr->link);
 			break;
 
 		default:
@@ -224,10 +224,11 @@
 	return newdentry;
 }
 
-struct dentry *ovl_create_temp(struct dentry *workdir, struct ovl_cattr *attr)
+struct dentry *ovl_create_temp(struct ovl_fs *ofs, struct dentry *workdir,
+			       struct ovl_cattr *attr)
 {
-	return ovl_create_real(d_inode(workdir), ovl_lookup_temp(workdir),
-			       attr);
+	return ovl_create_real(ofs, d_inode(workdir),
+			       ovl_lookup_temp(ofs, workdir), attr);
 }
 
 static int ovl_set_opaque_xerr(struct dentry *dentry, struct dentry *upper,
@@ -268,8 +269,7 @@
 
 	ovl_dir_modified(dentry->d_parent, false);
 	ovl_dentry_set_upper_alias(dentry);
-	ovl_dentry_update_reval(dentry, newdentry,
-			DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE);
+	ovl_dentry_init_reval(dentry, newdentry);
 
 	if (!hardlink) {
 		/*
@@ -331,7 +331,7 @@
 		attr->mode &= ~current_umask();
 
 	inode_lock_nested(udir, I_MUTEX_PARENT);
-	newdentry = ovl_create_real(udir,
+	newdentry = ovl_create_real(ofs, udir,
 				    lookup_one_len(dentry->d_name.name,
 						   upperdir,
 						   dentry->d_name.len),
@@ -354,7 +354,7 @@
 	return err;
 
 out_cleanup:
-	ovl_cleanup(udir, newdentry);
+	ovl_cleanup(ofs, udir, newdentry);
 	dput(newdentry);
 	goto out_unlock;
 }
@@ -362,6 +362,7 @@
 static struct dentry *ovl_clear_empty(struct dentry *dentry,
 				      struct list_head *list)
 {
+	struct ovl_fs *ofs = OVL_FS(dentry->d_sb);
 	struct dentry *workdir = ovl_workdir(dentry);
 	struct inode *wdir = workdir->d_inode;
 	struct dentry *upperdir = ovl_dentry_upper(dentry->d_parent);
@@ -392,7 +393,7 @@
 	if (upper->d_parent->d_inode != udir)
 		goto out_unlock;
 
-	opaquedir = ovl_create_temp(workdir, OVL_CATTR(stat.mode));
+	opaquedir = ovl_create_temp(ofs, workdir, OVL_CATTR(stat.mode));
 	err = PTR_ERR(opaquedir);
 	if (IS_ERR(opaquedir))
 		goto out_unlock;
@@ -411,12 +412,12 @@
 	if (err)
 		goto out_cleanup;
 
-	err = ovl_do_rename(wdir, opaquedir, udir, upper, RENAME_EXCHANGE);
+	err = ovl_do_rename(ofs, wdir, opaquedir, udir, upper, RENAME_EXCHANGE);
 	if (err)
 		goto out_cleanup;
 
-	ovl_cleanup_whiteouts(upper, list);
-	ovl_cleanup(wdir, upper);
+	ovl_cleanup_whiteouts(ofs, upper, list);
+	ovl_cleanup(ofs, wdir, upper);
 	unlock_rename(workdir, upperdir);
 
 	/* dentry's upper doesn't match now, get rid of it */
@@ -425,7 +426,7 @@
 	return opaquedir;
 
 out_cleanup:
-	ovl_cleanup(wdir, opaquedir);
+	ovl_cleanup(ofs, wdir, opaquedir);
 	dput(opaquedir);
 out_unlock:
 	unlock_rename(workdir, upperdir);
@@ -433,8 +434,8 @@
 	return ERR_PTR(err);
 }
 
-static int ovl_set_upper_acl(struct dentry *upperdentry, const char *name,
-			     const struct posix_acl *acl)
+static int ovl_set_upper_acl(struct ovl_fs *ofs, struct dentry *upperdentry,
+			     const char *name, const struct posix_acl *acl)
 {
 	void *buffer;
 	size_t size;
@@ -452,7 +453,7 @@
 	if (err < 0)
 		goto out_free;
 
-	err = vfs_setxattr(&init_user_ns, upperdentry, name, buffer, size, XATTR_CREATE);
+	err = ovl_do_setxattr(ofs, upperdentry, name, buffer, size, XATTR_CREATE);
 out_free:
 	kfree(buffer);
 	return err;
@@ -461,6 +462,7 @@
 static int ovl_create_over_whiteout(struct dentry *dentry, struct inode *inode,
 				    struct ovl_cattr *cattr)
 {
+	struct ovl_fs *ofs = OVL_FS(dentry->d_sb);
 	struct dentry *workdir = ovl_workdir(dentry);
 	struct inode *wdir = workdir->d_inode;
 	struct dentry *upperdir = ovl_dentry_upper(dentry->d_parent);
@@ -495,7 +497,7 @@
 	if (d_is_negative(upper) || !IS_WHITEOUT(d_inode(upper)))
 		goto out_dput;
 
-	newdentry = ovl_create_temp(workdir, cattr);
+	newdentry = ovl_create_temp(ofs, workdir, cattr);
 	err = PTR_ERR(newdentry);
 	if (IS_ERR(newdentry))
 		goto out_dput;
@@ -517,13 +519,13 @@
 			goto out_cleanup;
 	}
 	if (!hardlink) {
-		err = ovl_set_upper_acl(newdentry, XATTR_NAME_POSIX_ACL_ACCESS,
-					acl);
+		err = ovl_set_upper_acl(ofs, newdentry,
+					XATTR_NAME_POSIX_ACL_ACCESS, acl);
 		if (err)
 			goto out_cleanup;
 
-		err = ovl_set_upper_acl(newdentry, XATTR_NAME_POSIX_ACL_DEFAULT,
-					default_acl);
+		err = ovl_set_upper_acl(ofs, newdentry,
+					XATTR_NAME_POSIX_ACL_DEFAULT, default_acl);
 		if (err)
 			goto out_cleanup;
 	}
@@ -533,20 +535,20 @@
 		if (err)
 			goto out_cleanup;
 
-		err = ovl_do_rename(wdir, newdentry, udir, upper,
+		err = ovl_do_rename(ofs, wdir, newdentry, udir, upper,
 				    RENAME_EXCHANGE);
 		if (err)
 			goto out_cleanup;
 
-		ovl_cleanup(wdir, upper);
+		ovl_cleanup(ofs, wdir, upper);
 	} else {
-		err = ovl_do_rename(wdir, newdentry, udir, upper, 0);
+		err = ovl_do_rename(ofs, wdir, newdentry, udir, upper, 0);
 		if (err)
 			goto out_cleanup;
 	}
 	err = ovl_instantiate(dentry, inode, newdentry, hardlink);
 	if (err) {
-		ovl_cleanup(udir, newdentry);
+		ovl_cleanup(ofs, udir, newdentry);
 		dput(newdentry);
 	}
 out_dput:
@@ -561,7 +563,7 @@
 	return err;
 
 out_cleanup:
-	ovl_cleanup(wdir, newdentry);
+	ovl_cleanup(ofs, wdir, newdentry);
 	dput(newdentry);
 	goto out_dput;
 }
@@ -590,28 +592,42 @@
 			goto out_revert_creds;
 	}
 
-	err = -ENOMEM;
-	override_cred = prepare_creds();
-	if (override_cred) {
+	if (!attr->hardlink) {
+		err = -ENOMEM;
+		override_cred = prepare_creds();
+		if (!override_cred)
+			goto out_revert_creds;
+		/*
+		 * In the creation cases(create, mkdir, mknod, symlink),
+		 * ovl should transfer current's fs{u,g}id to underlying
+		 * fs. Because underlying fs want to initialize its new
+		 * inode owner using current's fs{u,g}id. And in this
+		 * case, the @inode is a new inode that is initialized
+		 * in inode_init_owner() to current's fs{u,g}id. So use
+		 * the inode's i_{u,g}id to override the cred's fs{u,g}id.
+		 *
+		 * But in the other hardlink case, ovl_link() does not
+		 * create a new inode, so just use the ovl mounter's
+		 * fs{u,g}id.
+		 */
 		override_cred->fsuid = inode->i_uid;
 		override_cred->fsgid = inode->i_gid;
-		if (!attr->hardlink) {
-			err = security_dentry_create_files_as(dentry,
-					attr->mode, &dentry->d_name, old_cred,
-					override_cred);
-			if (err) {
-				put_cred(override_cred);
-				goto out_revert_creds;
-			}
+		err = security_dentry_create_files_as(dentry,
+				attr->mode, &dentry->d_name, old_cred,
+				override_cred);
+		if (err) {
+			put_cred(override_cred);
+			goto out_revert_creds;
 		}
 		put_cred(override_creds(override_cred));
 		put_cred(override_cred);
-
-		if (!ovl_dentry_is_whiteout(dentry))
-			err = ovl_create_upper(dentry, inode, attr);
-		else
-			err = ovl_create_over_whiteout(dentry, inode, attr);
 	}
+
+	if (!ovl_dentry_is_whiteout(dentry))
+		err = ovl_create_upper(dentry, inode, attr);
+	else
+		err = ovl_create_over_whiteout(dentry, inode, attr);
+
 out_revert_creds:
 	revert_creds(old_cred);
 	return err;
@@ -801,6 +817,7 @@
 static int ovl_remove_upper(struct dentry *dentry, bool is_dir,
 			    struct list_head *list)
 {
+	struct ovl_fs *ofs = OVL_FS(dentry->d_sb);
 	struct dentry *upperdir = ovl_dentry_upper(dentry->d_parent);
 	struct inode *dir = upperdir->d_inode;
 	struct dentry *upper;
@@ -827,9 +844,9 @@
 		goto out_dput_upper;
 
 	if (is_dir)
-		err = vfs_rmdir(&init_user_ns, dir, upper);
+		err = ovl_do_rmdir(ofs, dir, upper);
 	else
-		err = vfs_unlink(&init_user_ns, dir, upper, NULL);
+		err = ovl_do_unlink(ofs, dir, upper);
 	ovl_dir_modified(dentry->d_parent, ovl_type_origin(dentry));
 
 	/*
@@ -881,7 +898,6 @@
 {
 	int err;
 	const struct cred *old_cred;
-	struct dentry *upperdentry;
 	bool lower_positive = ovl_lower_positive(dentry);
 	LIST_HEAD(list);
 
@@ -924,9 +940,8 @@
 	 * Note: we fail to update ctime if there was no copy-up, only a
 	 * whiteout
 	 */
-	upperdentry = ovl_dentry_upper(dentry);
-	if (upperdentry)
-		ovl_copyattr(d_inode(upperdentry), d_inode(dentry));
+	if (ovl_dentry_upper(dentry))
+		ovl_copyattr(d_inode(dentry));
 
 out_drop_write:
 	ovl_drop_write(dentry);
@@ -1096,6 +1111,7 @@
 	bool samedir = olddir == newdir;
 	struct dentry *opaquedir = NULL;
 	const struct cred *old_cred = NULL;
+	struct ovl_fs *ofs = OVL_FS(old->d_sb);
 	LIST_HEAD(list);
 
 	err = -EINVAL;
@@ -1252,13 +1268,13 @@
 	if (err)
 		goto out_dput;
 
-	err = ovl_do_rename(old_upperdir->d_inode, olddentry,
+	err = ovl_do_rename(ofs, old_upperdir->d_inode, olddentry,
 			    new_upperdir->d_inode, newdentry, flags);
 	if (err)
 		goto out_dput;
 
 	if (cleanup_whiteout)
-		ovl_cleanup(old_upperdir->d_inode, newdentry);
+		ovl_cleanup(ofs, old_upperdir->d_inode, newdentry);
 
 	if (overwrite && d_inode(new)) {
 		if (new_is_dir)
@@ -1273,9 +1289,9 @@
 			 (d_inode(new) && ovl_type_origin(new)));
 
 	/* copy ctime: */
-	ovl_copyattr(d_inode(olddentry), d_inode(old));
+	ovl_copyattr(d_inode(old));
 	if (d_inode(new) && ovl_dentry_upper(new))
-		ovl_copyattr(d_inode(newdentry), d_inode(new));
+		ovl_copyattr(d_inode(new));
 
 out_dput:
 	dput(newdentry);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/export.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/export.c
@@ -259,7 +259,7 @@
 		return FILEID_INVALID;
 
 	dentry = d_find_any_alias(inode);
-	if (WARN_ON(!dentry))
+	if (!dentry)
 		return FILEID_INVALID;
 
 	bytes = ovl_dentry_to_fid(ofs, dentry, fid, buflen);
@@ -326,8 +326,7 @@
 	if (upper_alias)
 		ovl_dentry_set_upper_alias(dentry);
 
-	ovl_dentry_update_reval(dentry, upper,
-			DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE);
+	ovl_dentry_init_reval(dentry, upper);
 
 	return d_instantiate_anon(dentry, inode);
 
@@ -791,7 +790,7 @@
 		return ERR_PTR(-ENOMEM);
 
 	/* Copy unaligned inner fh into aligned buffer */
-	memcpy(&fh->fb, fid, buflen - OVL_FH_WIRE_OFFSET);
+	memcpy(fh->buf, fid, buflen - OVL_FH_WIRE_OFFSET);
 	return fh;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/file.c
@@ -17,8 +17,8 @@
 
 struct ovl_aio_req {
 	struct kiocb iocb;
+	refcount_t ref;
 	struct kiocb *orig_iocb;
-	struct fd fd;
 };
 
 static struct kmem_cache *ovl_aio_request_cachep;
@@ -39,6 +39,7 @@
 static struct file *ovl_open_realfile(const struct file *file,
 				      struct inode *realinode)
 {
+	struct path realpath;
 	struct inode *inode = file_inode(file);
 	struct file *realfile;
 	const struct cred *old_cred;
@@ -57,7 +58,8 @@
 		if (!inode_owner_or_capable(&init_user_ns, realinode))
 			flags &= ~O_NOATIME;
 
-		realfile = open_with_fake_path(&file->f_path, flags, realinode,
+		ovl_path_real(file->f_path.dentry, &realpath);
+		realfile = open_with_fake_path(&realpath, flags, realinode,
 					       current_cred());
 	}
 	revert_creds(old_cred);
@@ -252,6 +254,14 @@
 	return flags;
 }
 
+static inline void ovl_aio_put(struct ovl_aio_req *aio_req)
+{
+	if (refcount_dec_and_test(&aio_req->ref)) {
+		fput(aio_req->iocb.ki_filp);
+		kmem_cache_free(ovl_aio_request_cachep, aio_req);
+	}
+}
+
 static void ovl_aio_cleanup_handler(struct ovl_aio_req *aio_req)
 {
 	struct kiocb *iocb = &aio_req->iocb;
@@ -264,12 +274,11 @@
 		__sb_writers_acquired(file_inode(iocb->ki_filp)->i_sb,
 				      SB_FREEZE_WRITE);
 		file_end_write(iocb->ki_filp);
-		ovl_copyattr(ovl_inode_real(inode), inode);
+		ovl_copyattr(inode);
 	}
 
 	orig_iocb->ki_pos = iocb->ki_pos;
-	fdput(aio_req->fd);
-	kmem_cache_free(ovl_aio_request_cachep, aio_req);
+	ovl_aio_put(aio_req);
 }
 
 static void ovl_aio_rw_complete(struct kiocb *iocb, long res, long res2)
@@ -314,12 +323,13 @@
 		if (!aio_req)
 			goto out;
 
-		aio_req->fd = real;
 		real.flags = 0;
 		aio_req->orig_iocb = iocb;
-		kiocb_clone(&aio_req->iocb, iocb, real.file);
+		kiocb_clone(&aio_req->iocb, iocb, get_file(real.file));
 		aio_req->iocb.ki_complete = ovl_aio_rw_complete;
+		refcount_set(&aio_req->ref, 2);
 		ret = vfs_iocb_iter_read(real.file, &aio_req->iocb, iter);
+		ovl_aio_put(aio_req);
 		if (ret != -EIOCBQUEUED)
 			ovl_aio_cleanup_handler(aio_req);
 	}
@@ -346,7 +356,7 @@
 
 	inode_lock(inode);
 	/* Update mode */
-	ovl_copyattr(ovl_inode_real(inode), inode);
+	ovl_copyattr(inode);
 	ret = file_remove_privs(file);
 	if (ret)
 		goto out_unlock;
@@ -371,7 +381,7 @@
 				     ovl_iocb_to_rwf(ifl));
 		file_end_write(real.file);
 		/* Update size */
-		ovl_copyattr(ovl_inode_real(inode), inode);
+		ovl_copyattr(inode);
 	} else {
 		struct ovl_aio_req *aio_req;
 
@@ -384,13 +394,14 @@
 		/* Pacify lockdep, same trick as done in aio_write() */
 		__sb_writers_release(file_inode(real.file)->i_sb,
 				     SB_FREEZE_WRITE);
-		aio_req->fd = real;
 		real.flags = 0;
 		aio_req->orig_iocb = iocb;
-		kiocb_clone(&aio_req->iocb, iocb, real.file);
+		kiocb_clone(&aio_req->iocb, iocb, get_file(real.file));
 		aio_req->iocb.ki_flags = ifl;
 		aio_req->iocb.ki_complete = ovl_aio_rw_complete;
+		refcount_set(&aio_req->ref, 2);
 		ret = vfs_iocb_iter_write(real.file, &aio_req->iocb, iter);
+		ovl_aio_put(aio_req);
 		if (ret != -EIOCBQUEUED)
 			ovl_aio_cleanup_handler(aio_req);
 	}
@@ -419,12 +430,11 @@
 	struct fd real;
 	const struct cred *old_cred;
 	struct inode *inode = file_inode(out);
-	struct inode *realinode = ovl_inode_real(inode);
 	ssize_t ret;
 
 	inode_lock(inode);
 	/* Update mode */
-	ovl_copyattr(realinode, inode);
+	ovl_copyattr(inode);
 	ret = file_remove_privs(out);
 	if (ret)
 		goto out_unlock;
@@ -440,7 +450,7 @@
 
 	file_end_write(real.file);
 	/* Update size */
-	ovl_copyattr(realinode, inode);
+	ovl_copyattr(inode);
 	revert_creds(old_cred);
 	fdput(real);
 
@@ -476,6 +486,49 @@
 	return ret;
 }
 
+/*
+ * In map_files_get_link() (fs/proc/base.c)
+ * we need to determine correct path from overlayfs.
+ * But real_mount(realfile->f_path.mnt) may be not
+ * equal to real_mount(file->f_path.mnt). In such case
+ * fdinfo of the same file which was opened from
+ * /proc/<pid>/map_files/... and "usual" path
+ * will show different mnt_id.
+ *
+ * We solve issue like in aufs by using additional
+ * field on struct vm_area_struct called "vm_prfile"
+ * which is used only for fdinfo/"printing" needs.
+ *
+ * See also mm/prfile.c
+ */
+#ifdef CONFIG_MMU
+static void ovl_vm_prfile_set(struct vm_area_struct *vma,
+			      struct file *file)
+{
+	get_file(file);
+	swap(vma->vm_prfile, file);
+	/* Drop reference count from previous file value */
+	if (file)
+		fput(file);
+}
+#else
+static void ovl_vm_prfile_set(struct vm_area_struct *vma,
+			      struct file *file)
+{
+	struct file *vm_region_file = file;
+
+	get_file(file);
+	get_file(vm_region_file);
+	swap(vma->vm_prfile, file);
+	swap(vma->vm_region->vm_prfile, vm_region_file);
+	/* Drop reference count from previous file values */
+	if (file)
+		fput(file);
+	if (vm_region_file)
+		fput(vm_region_file);
+}
+#endif
+
 static int ovl_mmap(struct file *file, struct vm_area_struct *vma)
 {
 	struct file *realfile = file->private_data;
@@ -493,6 +546,10 @@
 	old_cred = ovl_override_creds(file_inode(file)->i_sb);
 	ret = call_mmap(vma->vm_file, vma);
 	revert_creds(old_cred);
+
+	if (!ret)
+		ovl_vm_prfile_set(vma, file);
+
 	ovl_file_accessed(file);
 
 	return ret;
@@ -505,19 +562,29 @@
 	const struct cred *old_cred;
 	int ret;
 
+	inode_lock(inode);
+	/* Update mode */
+	ovl_copyattr(inode);
+	ret = file_remove_privs(file);
+	if (ret)
+		goto out_unlock;
+
 	ret = ovl_real_fdget(file, &real);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	old_cred = ovl_override_creds(file_inode(file)->i_sb);
 	ret = vfs_fallocate(real.file, mode, offset, len);
 	revert_creds(old_cred);
 
 	/* Update size */
-	ovl_copyattr(ovl_inode_real(inode), inode);
+	ovl_copyattr(inode);
 
 	fdput(real);
 
+out_unlock:
+	inode_unlock(inode);
+
 	return ret;
 }
 
@@ -555,14 +622,23 @@
 	const struct cred *old_cred;
 	loff_t ret;
 
+	inode_lock(inode_out);
+	if (op != OVL_DEDUPE) {
+		/* Update mode */
+		ovl_copyattr(inode_out);
+		ret = file_remove_privs(file_out);
+		if (ret)
+			goto out_unlock;
+	}
+
 	ret = ovl_real_fdget(file_out, &real_out);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	ret = ovl_real_fdget(file_in, &real_in);
 	if (ret) {
 		fdput(real_out);
-		return ret;
+		goto out_unlock;
 	}
 
 	old_cred = ovl_override_creds(file_inode(file_out)->i_sb);
@@ -586,11 +662,14 @@
 	revert_creds(old_cred);
 
 	/* Update size */
-	ovl_copyattr(ovl_inode_real(inode_out), inode_out);
+	ovl_copyattr(inode_out);
 
 	fdput(real_in);
 	fdput(real_out);
 
+out_unlock:
+	inode_unlock(inode_out);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/inode.c
@@ -80,7 +80,7 @@
 		err = notify_change(&init_user_ns, upperdentry, attr, NULL);
 		revert_creds(old_cred);
 		if (!err)
-			ovl_copyattr(upperdentry->d_inode, dentry->d_inode);
+			ovl_copyattr(dentry->d_inode);
 		inode_unlock(upperdentry->d_inode);
 
 		if (winode)
@@ -342,6 +342,7 @@
 		  const void *value, size_t size, int flags)
 {
 	int err;
+	struct ovl_fs *ofs = OVL_FS(dentry->d_sb);
 	struct dentry *upperdentry = ovl_i_dentry_upper(inode);
 	struct dentry *realdentry = upperdentry ?: ovl_dentry_lower(dentry);
 	const struct cred *old_cred;
@@ -367,17 +368,17 @@
 	}
 
 	old_cred = ovl_override_creds(dentry->d_sb);
-	if (value)
-		err = vfs_setxattr(&init_user_ns, realdentry, name, value, size,
-				   flags);
-	else {
+	if (value) {
+		err = ovl_do_setxattr(ofs, realdentry, name, value, size,
+				      flags);
+	} else {
 		WARN_ON(flags != XATTR_REPLACE);
-		err = vfs_removexattr(&init_user_ns, realdentry, name);
+		err = ovl_do_removexattr(ofs, realdentry, name);
 	}
 	revert_creds(old_cred);
 
 	/* copy c/mtime */
-	ovl_copyattr(d_inode(realdentry), inode);
+	ovl_copyattr(inode);
 
 out_drop_write:
 	ovl_drop_write(dentry);
@@ -453,7 +454,15 @@
 	const struct cred *old_cred;
 	struct posix_acl *acl;
 
-	if (!IS_ENABLED(CONFIG_FS_POSIX_ACL) || !IS_POSIXACL(realinode))
+	if (!IS_ENABLED(CONFIG_FS_POSIX_ACL))
+		return NULL;
+
+	if (!realinode) {
+		WARN_ON(!rcu);
+		return ERR_PTR(-ECHILD);
+	}
+
+	if (!IS_POSIXACL(realinode))
 		return NULL;
 
 	if (rcu)
@@ -511,8 +520,13 @@
 	struct file *file;
 	unsigned int cmd;
 	int err;
+	unsigned int flags;
+
+	flags = O_RDONLY;
+	if (force_o_largefile())
+		flags |= O_LARGEFILE;
 
-	file = dentry_open(realpath, O_RDONLY, current_cred());
+	file = dentry_open(realpath, flags, current_cred());
 	if (IS_ERR(file))
 		return PTR_ERR(file);
 
@@ -579,7 +593,7 @@
 		inode_set_flags(inode, flags, OVL_COPY_I_FLAGS_MASK);
 
 		/* Update ctime */
-		ovl_copyattr(ovl_inode_real(inode), inode);
+		ovl_copyattr(inode);
 	}
 	ovl_drop_write(dentry);
 out:
@@ -610,7 +624,10 @@
 	if (err)
 		return err;
 
-	return vfs_fileattr_get(realpath->dentry, fa);
+	err = vfs_fileattr_get(realpath->dentry, fa);
+	if (err == -ENOIOCTLCMD)
+		err = -ENOTTY;
+	return err;
 }
 
 int ovl_fileattr_get(struct dentry *dentry, struct fileattr *fa)
@@ -774,16 +791,19 @@
 		    unsigned long ino, int fsid)
 {
 	struct inode *realinode;
+	struct ovl_inode *oi = OVL_I(inode);
 
 	if (oip->upperdentry)
-		OVL_I(inode)->__upperdentry = oip->upperdentry;
-	if (oip->lowerpath && oip->lowerpath->dentry)
-		OVL_I(inode)->lower = igrab(d_inode(oip->lowerpath->dentry));
+		oi->__upperdentry = oip->upperdentry;
+	if (oip->lowerpath && oip->lowerpath->dentry) {
+		oi->lowerpath.dentry = dget(oip->lowerpath->dentry);
+		oi->lowerpath.layer = oip->lowerpath->layer;
+	}
 	if (oip->lowerdata)
-		OVL_I(inode)->lowerdata = igrab(d_inode(oip->lowerdata));
+		oi->lowerdata = igrab(d_inode(oip->lowerdata));
 
 	realinode = ovl_inode_real(inode);
-	ovl_copyattr(realinode, inode);
+	ovl_copyattr(inode);
 	ovl_copyflags(realinode, inode);
 	ovl_map_ino(inode, ino, fsid);
 }
@@ -868,8 +888,8 @@
 	if (WARN_ON(len >= sizeof(buf)))
 		return -EIO;
 
-	return ovl_do_setxattr(OVL_FS(inode->i_sb), ovl_dentry_upper(dentry),
-			       OVL_XATTR_NLINK, buf, len);
+	return ovl_setxattr(OVL_FS(inode->i_sb), ovl_dentry_upper(dentry),
+			    OVL_XATTR_NLINK, buf, len);
 }
 
 int ovl_set_nlink_upper(struct dentry *dentry)
@@ -894,7 +914,7 @@
 	if (!lowerdentry || !upperdentry || d_inode(lowerdentry)->i_nlink == 1)
 		return fallback;
 
-	err = ovl_do_getxattr(ofs, upperdentry, OVL_XATTR_NLINK,
+	err = ovl_getxattr(ofs, upperdentry, OVL_XATTR_NLINK,
 			      &buf, sizeof(buf) - 1);
 	if (err < 0)
 		goto fail;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/namei.c
@@ -111,7 +111,7 @@
 	int res, err;
 	struct ovl_fh *fh = NULL;
 
-	res = ovl_do_getxattr(ofs, dentry, ox, NULL, 0);
+	res = ovl_getxattr(ofs, dentry, ox, NULL, 0);
 	if (res < 0) {
 		if (res == -ENODATA || res == -EOPNOTSUPP)
 			return NULL;
@@ -125,7 +125,7 @@
 	if (!fh)
 		return ERR_PTR(-ENOMEM);
 
-	res = ovl_do_getxattr(ofs, dentry, ox, fh->buf, res);
+	res = ovl_getxattr(ofs, dentry, ox, fh->buf, res);
 	if (res < 0)
 		goto fail;
 
@@ -464,7 +464,7 @@
 
 	err = ovl_verify_fh(ofs, dentry, ox, fh);
 	if (set && err == -ENODATA)
-		err = ovl_do_setxattr(ofs, dentry, ox, fh->buf, fh->fb.len);
+		err = ovl_setxattr(ofs, dentry, ox, fh->buf, fh->fb.len);
 	if (err)
 		goto fail;
 
@@ -1103,8 +1103,7 @@
 			ovl_set_flag(OVL_UPPERDATA, inode);
 	}
 
-	ovl_dentry_update_reval(dentry, upperdentry,
-			DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE);
+	ovl_dentry_init_reval(dentry, upperdentry);
 
 	revert_creds(old_cred);
 	if (origin_path) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/overlayfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/overlayfs.h
@@ -107,7 +107,7 @@
 	u8 padding[3];	/* make sure fb.fid is 32bit aligned */
 	union {
 		struct ovl_fb fb;
-		u8 buf[0];
+		DECLARE_FLEX_ARRAY(u8, buf);
 	};
 } __packed;
 
@@ -122,7 +122,8 @@
 	return ovl_xattr_table[ox][ofs->config.userxattr];
 }
 
-static inline int ovl_do_rmdir(struct inode *dir, struct dentry *dentry)
+static inline int ovl_do_rmdir(struct ovl_fs *ofs,
+			       struct inode *dir, struct dentry *dentry)
 {
 	int err = vfs_rmdir(&init_user_ns, dir, dentry);
 
@@ -130,7 +131,8 @@
 	return err;
 }
 
-static inline int ovl_do_unlink(struct inode *dir, struct dentry *dentry)
+static inline int ovl_do_unlink(struct ovl_fs *ofs, struct inode *dir,
+				struct dentry *dentry)
 {
 	int err = vfs_unlink(&init_user_ns, dir, dentry, NULL);
 
@@ -138,8 +140,8 @@
 	return err;
 }
 
-static inline int ovl_do_link(struct dentry *old_dentry, struct inode *dir,
-			      struct dentry *new_dentry)
+static inline int ovl_do_link(struct ovl_fs *ofs, struct dentry *old_dentry,
+			      struct inode *dir, struct dentry *new_dentry)
 {
 	int err = vfs_link(old_dentry, &init_user_ns, dir, new_dentry, NULL);
 
@@ -147,7 +149,8 @@
 	return err;
 }
 
-static inline int ovl_do_create(struct inode *dir, struct dentry *dentry,
+static inline int ovl_do_create(struct ovl_fs *ofs,
+				struct inode *dir, struct dentry *dentry,
 				umode_t mode)
 {
 	int err = vfs_create(&init_user_ns, dir, dentry, mode, true);
@@ -156,7 +159,8 @@
 	return err;
 }
 
-static inline int ovl_do_mkdir(struct inode *dir, struct dentry *dentry,
+static inline int ovl_do_mkdir(struct ovl_fs *ofs,
+			       struct inode *dir, struct dentry *dentry,
 			       umode_t mode)
 {
 	int err = vfs_mkdir(&init_user_ns, dir, dentry, mode);
@@ -164,7 +168,8 @@
 	return err;
 }
 
-static inline int ovl_do_mknod(struct inode *dir, struct dentry *dentry,
+static inline int ovl_do_mknod(struct ovl_fs *ofs,
+			       struct inode *dir, struct dentry *dentry,
 			       umode_t mode, dev_t dev)
 {
 	int err = vfs_mknod(&init_user_ns, dir, dentry, mode, dev);
@@ -173,7 +178,8 @@
 	return err;
 }
 
-static inline int ovl_do_symlink(struct inode *dir, struct dentry *dentry,
+static inline int ovl_do_symlink(struct ovl_fs *ofs,
+				 struct inode *dir, struct dentry *dentry,
 				 const char *oldname)
 {
 	int err = vfs_symlink(&init_user_ns, dir, dentry, oldname);
@@ -183,10 +189,9 @@
 }
 
 static inline ssize_t ovl_do_getxattr(struct ovl_fs *ofs, struct dentry *dentry,
-				      enum ovl_xattr ox, void *value,
+				      const char *name, void *value,
 				      size_t size)
 {
-	const char *name = ovl_xattr(ofs, ox);
 	int err = vfs_getxattr(&init_user_ns, dentry, name, value, size);
 	int len = (value && err > 0) ? err : 0;
 
@@ -195,29 +200,59 @@
 	return err;
 }
 
+static inline ssize_t ovl_getxattr(struct ovl_fs *ofs, struct dentry *dentry,
+				   enum ovl_xattr ox, void *value,
+				   size_t size)
+{
+	return ovl_do_getxattr(ofs, dentry, ovl_xattr(ofs, ox), value, size);
+}
+
 static inline int ovl_do_setxattr(struct ovl_fs *ofs, struct dentry *dentry,
-				  enum ovl_xattr ox, const void *value,
-				  size_t size)
+				  const char *name, const void *value,
+				  size_t size, int flags)
 {
-	const char *name = ovl_xattr(ofs, ox);
-	int err = vfs_setxattr(&init_user_ns, dentry, name, value, size, 0);
-	pr_debug("setxattr(%pd2, \"%s\", \"%*pE\", %zu, 0) = %i\n",
-		 dentry, name, min((int)size, 48), value, size, err);
+	struct inode *inode = dentry->d_inode;
+	int err;
+
+	inode_lock(inode);
+	err = __vfs_setxattr_noperm(&init_user_ns, dentry, name, value, size, flags);
+	inode_unlock(inode);
+
+	pr_debug("setxattr(%pd2, \"%s\", \"%*pE\", %zu, %d) = %i\n",
+		 dentry, name, min((int)size, 48), value, size, flags, err);
 	return err;
 }
 
+static inline int ovl_setxattr(struct ovl_fs *ofs, struct dentry *dentry,
+			       enum ovl_xattr ox, const void *value,
+			       size_t size)
+{
+	return ovl_do_setxattr(ofs, dentry, ovl_xattr(ofs, ox), value, size, 0);
+}
+
 static inline int ovl_do_removexattr(struct ovl_fs *ofs, struct dentry *dentry,
-				     enum ovl_xattr ox)
+				     const char *name)
 {
-	const char *name = ovl_xattr(ofs, ox);
-	int err = vfs_removexattr(&init_user_ns, dentry, name);
+	struct inode *inode = dentry->d_inode;
+	int err;
+
+	inode_lock(inode);
+	err = __vfs_removexattr_noperm(&init_user_ns, dentry, name);
+	inode_unlock(inode);
+
 	pr_debug("removexattr(%pd2, \"%s\") = %i\n", dentry, name, err);
 	return err;
 }
 
-static inline int ovl_do_rename(struct inode *olddir, struct dentry *olddentry,
-				struct inode *newdir, struct dentry *newdentry,
-				unsigned int flags)
+static inline int ovl_removexattr(struct ovl_fs *ofs, struct dentry *dentry,
+				  enum ovl_xattr ox)
+{
+	return ovl_do_removexattr(ofs, dentry, ovl_xattr(ofs, ox));
+}
+
+static inline int ovl_do_rename(struct ovl_fs *ofs, struct inode *olddir,
+				struct dentry *olddentry, struct inode *newdir,
+				struct dentry *newdentry, unsigned int flags)
 {
 	int err;
 	struct renamedata rd = {
@@ -239,14 +274,16 @@
 	return err;
 }
 
-static inline int ovl_do_whiteout(struct inode *dir, struct dentry *dentry)
+static inline int ovl_do_whiteout(struct ovl_fs *ofs,
+				  struct inode *dir, struct dentry *dentry)
 {
 	int err = vfs_whiteout(&init_user_ns, dir, dentry);
 	pr_debug("whiteout(%pd2) = %i\n", dentry, err);
 	return err;
 }
 
-static inline struct dentry *ovl_do_tmpfile(struct dentry *dentry, umode_t mode)
+static inline struct dentry *ovl_do_tmpfile(struct ovl_fs *ofs,
+					    struct dentry *dentry, umode_t mode)
 {
 	struct dentry *ret = vfs_tmpfile(&init_user_ns, dentry, mode, 0);
 	int err = PTR_ERR_OR_ZERO(ret);
@@ -286,17 +323,21 @@
 bool ovl_verify_lower(struct super_block *sb);
 struct ovl_entry *ovl_alloc_entry(unsigned int numlower);
 bool ovl_dentry_remote(struct dentry *dentry);
-void ovl_dentry_update_reval(struct dentry *dentry, struct dentry *upperdentry,
-			     unsigned int mask);
+void ovl_dentry_update_reval(struct dentry *dentry, struct dentry *realdentry);
+void ovl_dentry_init_reval(struct dentry *dentry, struct dentry *upperdentry);
+void ovl_dentry_init_flags(struct dentry *dentry, struct dentry *upperdentry,
+			   unsigned int mask);
 bool ovl_dentry_weird(struct dentry *dentry);
 enum ovl_path_type ovl_path_type(struct dentry *dentry);
 void ovl_path_upper(struct dentry *dentry, struct path *path);
 void ovl_path_lower(struct dentry *dentry, struct path *path);
 void ovl_path_lowerdata(struct dentry *dentry, struct path *path);
+void ovl_i_path_real(struct inode *inode, struct path *path);
 enum ovl_path_type ovl_path_real(struct dentry *dentry, struct path *path);
 struct dentry *ovl_dentry_upper(struct dentry *dentry);
 struct dentry *ovl_dentry_lower(struct dentry *dentry);
 struct dentry *ovl_dentry_lowerdata(struct dentry *dentry);
+const struct ovl_layer *ovl_i_layer_lower(struct inode *inode);
 const struct ovl_layer *ovl_layer_lower(struct dentry *dentry);
 struct dentry *ovl_dentry_real(struct dentry *dentry);
 struct dentry *ovl_i_dentry_upper(struct inode *inode);
@@ -461,12 +502,13 @@
 extern const struct file_operations ovl_dir_operations;
 struct file *ovl_dir_real_file(const struct file *file, bool want_upper);
 int ovl_check_empty_dir(struct dentry *dentry, struct list_head *list);
-void ovl_cleanup_whiteouts(struct dentry *upper, struct list_head *list);
+void ovl_cleanup_whiteouts(struct ovl_fs *ofs, struct dentry *upper,
+			   struct list_head *list);
 void ovl_cache_free(struct list_head *list);
 void ovl_dir_cache_free(struct inode *inode);
 int ovl_check_d_type_supported(struct path *realpath);
-int ovl_workdir_cleanup(struct inode *dir, struct vfsmount *mnt,
-			struct dentry *dentry, int level);
+int ovl_workdir_cleanup(struct ovl_fs *ofs, struct inode *dir,
+			struct vfsmount *mnt, struct dentry *dentry, int level);
 int ovl_indexdir_cleanup(struct ovl_fs *ofs);
 
 /*
@@ -520,16 +562,7 @@
 struct inode *ovl_get_trap_inode(struct super_block *sb, struct dentry *dir);
 struct inode *ovl_get_inode(struct super_block *sb,
 			    struct ovl_inode_params *oip);
-static inline void ovl_copyattr(struct inode *from, struct inode *to)
-{
-	to->i_uid = from->i_uid;
-	to->i_gid = from->i_gid;
-	to->i_mode = from->i_mode;
-	to->i_atime = from->i_atime;
-	to->i_mtime = from->i_mtime;
-	to->i_ctime = from->i_ctime;
-	i_size_write(to, i_size_read(from));
-}
+void ovl_copyattr(struct inode *to);
 
 /* vfs inode flags copied from real to ovl inode */
 #define OVL_COPY_I_FLAGS_MASK	(S_SYNC | S_NOATIME | S_APPEND | S_IMMUTABLE)
@@ -570,11 +603,15 @@
 
 #define OVL_CATTR(m) (&(struct ovl_cattr) { .mode = (m) })
 
-struct dentry *ovl_create_real(struct inode *dir, struct dentry *newdentry,
+int ovl_mkdir_real(struct ovl_fs *ofs, struct inode *dir,
+		   struct dentry **newdentry, umode_t mode);
+struct dentry *ovl_create_real(struct ovl_fs *ofs,
+			       struct inode *dir, struct dentry *newdentry,
+			       struct ovl_cattr *attr);
+int ovl_cleanup(struct ovl_fs *ofs, struct inode *dir, struct dentry *dentry);
+struct dentry *ovl_lookup_temp(struct ovl_fs *ofs, struct dentry *workdir);
+struct dentry *ovl_create_temp(struct ovl_fs *ofs, struct dentry *workdir,
 			       struct ovl_cattr *attr);
-int ovl_cleanup(struct inode *dir, struct dentry *dentry);
-struct dentry *ovl_lookup_temp(struct dentry *workdir);
-struct dentry *ovl_create_temp(struct dentry *workdir, struct ovl_cattr *attr);
 
 /* file.c */
 extern const struct file_operations ovl_file_operations;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/ovl_entry.h
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/ovl_entry.h
@@ -32,6 +32,7 @@
 };
 
 struct ovl_layer {
+	/* ovl_free_fs() relies on @mnt being the first member! */
 	struct vfsmount *mnt;
 	/* Trap in ovl inode cache */
 	struct inode *trap;
@@ -42,6 +43,14 @@
 	int fsid;
 };
 
+/*
+ * ovl_free_fs() relies on @mnt being the first member when unmounting
+ * the private mounts created for each layer. Let's check both the
+ * offset and type.
+ */
+static_assert(offsetof(struct ovl_layer, mnt) == 0);
+static_assert(__same_type(typeof_member(struct ovl_layer, mnt), struct vfsmount *));
+
 struct ovl_path {
 	const struct ovl_layer *layer;
 	struct dentry *dentry;
@@ -129,7 +138,7 @@
 	unsigned long flags;
 	struct inode vfs_inode;
 	struct dentry *__upperdentry;
-	struct inode *lower;
+	struct ovl_path lowerpath;
 
 	/* synchronize copy up and more */
 	struct mutex lock;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/readdir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/readdir.c
@@ -623,8 +623,8 @@
 		 * Removing the "impure" xattr is best effort.
 		 */
 		if (!ovl_want_write(dentry)) {
-			ovl_do_removexattr(ofs, ovl_dentry_upper(dentry),
-					   OVL_XATTR_IMPURE);
+			ovl_removexattr(ofs, ovl_dentry_upper(dentry),
+					OVL_XATTR_IMPURE);
 			ovl_drop_write(dentry);
 		}
 		ovl_clear_flag(OVL_IMPURE, d_inode(dentry));
@@ -1001,7 +1001,8 @@
 	return err;
 }
 
-void ovl_cleanup_whiteouts(struct dentry *upper, struct list_head *list)
+void ovl_cleanup_whiteouts(struct ovl_fs *ofs, struct dentry *upper,
+			   struct list_head *list)
 {
 	struct ovl_cache_entry *p;
 
@@ -1020,7 +1021,7 @@
 			continue;
 		}
 		if (dentry->d_inode)
-			ovl_cleanup(upper->d_inode, dentry);
+			ovl_cleanup(ofs, upper->d_inode, dentry);
 		dput(dentry);
 	}
 	inode_unlock(upper->d_inode);
@@ -1064,7 +1065,8 @@
 
 #define OVL_INCOMPATDIR_NAME "incompat"
 
-static int ovl_workdir_cleanup_recurse(struct path *path, int level)
+static int ovl_workdir_cleanup_recurse(struct ovl_fs *ofs, struct path *path,
+				       int level)
 {
 	int err;
 	struct inode *dir = path->dentry->d_inode;
@@ -1115,7 +1117,7 @@
 		if (IS_ERR(dentry))
 			continue;
 		if (dentry->d_inode)
-			err = ovl_workdir_cleanup(dir, path->mnt, dentry, level);
+			err = ovl_workdir_cleanup(ofs, dir, path->mnt, dentry, level);
 		dput(dentry);
 		if (err)
 			break;
@@ -1126,24 +1128,24 @@
 	return err;
 }
 
-int ovl_workdir_cleanup(struct inode *dir, struct vfsmount *mnt,
-			 struct dentry *dentry, int level)
+int ovl_workdir_cleanup(struct ovl_fs *ofs, struct inode *dir,
+			struct vfsmount *mnt, struct dentry *dentry, int level)
 {
 	int err;
 
 	if (!d_is_dir(dentry) || level > 1) {
-		return ovl_cleanup(dir, dentry);
+		return ovl_cleanup(ofs, dir, dentry);
 	}
 
-	err = ovl_do_rmdir(dir, dentry);
+	err = ovl_do_rmdir(ofs, dir, dentry);
 	if (err) {
 		struct path path = { .mnt = mnt, .dentry = dentry };
 
 		inode_unlock(dir);
-		err = ovl_workdir_cleanup_recurse(&path, level + 1);
+		err = ovl_workdir_cleanup_recurse(ofs, &path, level + 1);
 		inode_lock_nested(dir, I_MUTEX_PARENT);
 		if (!err)
-			err = ovl_cleanup(dir, dentry);
+			err = ovl_cleanup(ofs, dir, dentry);
 	}
 
 	return err;
@@ -1187,7 +1189,7 @@
 		}
 		/* Cleanup leftover from index create/cleanup attempt */
 		if (index->d_name.name[0] == '#') {
-			err = ovl_workdir_cleanup(dir, path.mnt, index, 1);
+			err = ovl_workdir_cleanup(ofs, dir, path.mnt, index, 1);
 			if (err)
 				break;
 			goto next;
@@ -1197,7 +1199,7 @@
 			goto next;
 		} else if (err == -ESTALE) {
 			/* Cleanup stale index entries */
-			err = ovl_cleanup(dir, index);
+			err = ovl_cleanup(ofs, dir, index);
 		} else if (err != -ENOENT) {
 			/*
 			 * Abort mount to avoid corrupting the index if
@@ -1213,7 +1215,7 @@
 			err = ovl_cleanup_and_whiteout(ofs, dir, index);
 		} else {
 			/* Cleanup orphan index entries */
-			err = ovl_cleanup(dir, index);
+			err = ovl_cleanup(ofs, dir, index);
 		}
 
 		if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/super.c
@@ -138,11 +138,16 @@
 					unsigned int flags, bool weak)
 {
 	struct ovl_entry *oe = dentry->d_fsdata;
+	struct inode *inode = d_inode_rcu(dentry);
 	struct dentry *upper;
 	unsigned int i;
 	int ret = 1;
 
-	upper = ovl_dentry_upper(dentry);
+	/* Careful in RCU mode */
+	if (!inode)
+		return -ECHILD;
+
+	upper = ovl_i_dentry_upper(inode);
 	if (upper)
 		ret = ovl_revalidate_real(upper, flags, weak);
 
@@ -184,7 +189,8 @@
 	oi->version = 0;
 	oi->flags = 0;
 	oi->__upperdentry = NULL;
-	oi->lower = NULL;
+	oi->lowerpath.dentry = NULL;
+	oi->lowerpath.layer = NULL;
 	oi->lowerdata = NULL;
 	mutex_init(&oi->lock);
 
@@ -205,7 +211,7 @@
 	struct ovl_inode *oi = OVL_I(inode);
 
 	dput(oi->__upperdentry);
-	iput(oi->lower);
+	dput(oi->lowerpath.dentry);
 	if (S_ISDIR(inode->i_mode))
 		ovl_dir_cache_free(inode);
 	else
@@ -778,7 +784,7 @@
 				goto out_unlock;
 
 			retried = true;
-			err = ovl_workdir_cleanup(dir, mnt, work, 0);
+			err = ovl_workdir_cleanup(ofs, dir, mnt, work, 0);
 			dput(work);
 			if (err == -EINVAL) {
 				work = ERR_PTR(err);
@@ -787,10 +793,14 @@
 			goto retry;
 		}
 
-		work = ovl_create_real(dir, work, OVL_CATTR(attr.ia_mode));
-		err = PTR_ERR(work);
-		if (IS_ERR(work))
-			goto out_err;
+		err = ovl_mkdir_real(ofs, dir, &work, attr.ia_mode);
+		if (err)
+			goto out_dput;
+
+		/* Weird filesystem returning with hashed negative (kernfs)? */
+		err = -EINVAL;
+		if (d_really_is_negative(work))
+			goto out_dput;
 
 		/*
 		 * Try to remove POSIX ACL xattrs from workdir.  We are good if:
@@ -805,13 +815,13 @@
 		 * allowed as upper are limited to "normal" ones, where checking
 		 * for the above two errors is sufficient.
 		 */
-		err = vfs_removexattr(&init_user_ns, work,
-				      XATTR_NAME_POSIX_ACL_DEFAULT);
+		err = ovl_do_removexattr(ofs, work,
+					 XATTR_NAME_POSIX_ACL_DEFAULT);
 		if (err && err != -ENODATA && err != -EOPNOTSUPP)
 			goto out_dput;
 
-		err = vfs_removexattr(&init_user_ns, work,
-				      XATTR_NAME_POSIX_ACL_ACCESS);
+		err = ovl_do_removexattr(ofs, work,
+					 XATTR_NAME_POSIX_ACL_ACCESS);
 		if (err && err != -ENODATA && err != -EOPNOTSUPP)
 			goto out_dput;
 
@@ -869,7 +879,7 @@
 		pr_err("filesystem on '%s' not supported\n", name);
 		goto out_put;
 	}
-	if (mnt_user_ns(path->mnt) != &init_user_ns) {
+	if (is_idmapped_mnt(path->mnt)) {
 		pr_err("idmapped layers are currently not supported\n");
 		goto out_put;
 	}
@@ -894,7 +904,8 @@
 		ovl_unescape(tmp);
 		err = ovl_mount_dir_noesc(tmp, path);
 
-		if (!err && path->dentry->d_flags & DCACHE_OP_REAL) {
+		if (!err && (path->dentry->d_flags & DCACHE_OP_REAL &&
+			     path->dentry->d_sb->s_magic != SHIFTFS_MAGIC)) {
 			pr_err("filesystem on '%s' not supported as upperdir\n",
 			       tmp);
 			path_put_init(path);
@@ -1252,8 +1263,9 @@
  * Returns 1 if RENAME_WHITEOUT is supported, 0 if not supported and
  * negative values if error is encountered.
  */
-static int ovl_check_rename_whiteout(struct dentry *workdir)
+static int ovl_check_rename_whiteout(struct ovl_fs *ofs)
 {
+	struct dentry *workdir = ofs->workdir;
 	struct inode *dir = d_inode(workdir);
 	struct dentry *temp;
 	struct dentry *dest;
@@ -1263,12 +1275,12 @@
 
 	inode_lock_nested(dir, I_MUTEX_PARENT);
 
-	temp = ovl_create_temp(workdir, OVL_CATTR(S_IFREG | 0));
+	temp = ovl_create_temp(ofs, workdir, OVL_CATTR(S_IFREG | 0));
 	err = PTR_ERR(temp);
 	if (IS_ERR(temp))
 		goto out_unlock;
 
-	dest = ovl_lookup_temp(workdir);
+	dest = ovl_lookup_temp(ofs, workdir);
 	err = PTR_ERR(dest);
 	if (IS_ERR(dest)) {
 		dput(temp);
@@ -1277,7 +1289,7 @@
 
 	/* Name is inline and stable - using snapshot as a copy helper */
 	take_dentry_name_snapshot(&name, temp);
-	err = ovl_do_rename(dir, temp, dir, dest, RENAME_WHITEOUT);
+	err = ovl_do_rename(ofs, dir, temp, dir, dest, RENAME_WHITEOUT);
 	if (err) {
 		if (err == -EINVAL)
 			err = 0;
@@ -1293,11 +1305,11 @@
 
 	/* Best effort cleanup of whiteout and temp file */
 	if (err)
-		ovl_cleanup(dir, whiteout);
+		ovl_cleanup(ofs, dir, whiteout);
 	dput(whiteout);
 
 cleanup_temp:
-	ovl_cleanup(dir, temp);
+	ovl_cleanup(ofs, dir, temp);
 	release_dentry_name_snapshot(&name);
 	dput(temp);
 	dput(dest);
@@ -1308,7 +1320,8 @@
 	return err;
 }
 
-static struct dentry *ovl_lookup_or_create(struct dentry *parent,
+static struct dentry *ovl_lookup_or_create(struct ovl_fs *ofs,
+					   struct dentry *parent,
 					   const char *name, umode_t mode)
 {
 	size_t len = strlen(name);
@@ -1317,7 +1330,7 @@
 	inode_lock_nested(parent->d_inode, I_MUTEX_PARENT);
 	child = lookup_one_len(name, parent, len);
 	if (!IS_ERR(child) && !child->d_inode)
-		child = ovl_create_real(parent->d_inode, child,
+		child = ovl_create_real(ofs, parent->d_inode, child,
 					OVL_CATTR(mode));
 	inode_unlock(parent->d_inode);
 	dput(parent);
@@ -1339,7 +1352,7 @@
 	const char *const *name = volatile_path;
 
 	for (ctr = ARRAY_SIZE(volatile_path); ctr; ctr--, name++) {
-		d = ovl_lookup_or_create(d, *name, ctr > 1 ? S_IFDIR : S_IFREG);
+		d = ovl_lookup_or_create(ofs, d, *name, ctr > 1 ? S_IFDIR : S_IFREG);
 		if (IS_ERR(d))
 			return PTR_ERR(d);
 	}
@@ -1387,7 +1400,7 @@
 		pr_warn("upper fs needs to support d_type.\n");
 
 	/* Check if upper/work fs supports O_TMPFILE */
-	temp = ovl_do_tmpfile(ofs->workdir, S_IFREG | 0);
+	temp = ovl_do_tmpfile(ofs, ofs->workdir, S_IFREG | 0);
 	ofs->tmpfile = !IS_ERR(temp);
 	if (ofs->tmpfile)
 		dput(temp);
@@ -1396,7 +1409,7 @@
 
 
 	/* Check if upper/work fs supports RENAME_WHITEOUT */
-	err = ovl_check_rename_whiteout(ofs->workdir);
+	err = ovl_check_rename_whiteout(ofs);
 	if (err < 0)
 		goto out;
 
@@ -1407,13 +1420,14 @@
 	/*
 	 * Check if upper/work fs supports (trusted|user).overlay.* xattr
 	 */
-	err = ovl_do_setxattr(ofs, ofs->workdir, OVL_XATTR_OPAQUE, "0", 1);
+	err = ovl_setxattr(ofs, ofs->workdir, OVL_XATTR_OPAQUE, "0", 1);
 	if (err) {
+		pr_warn("failed to set xattr on upper\n");
 		ofs->noxattr = true;
 		if (ofs->config.index || ofs->config.metacopy) {
 			ofs->config.index = false;
 			ofs->config.metacopy = false;
-			pr_warn("upper fs does not support xattr, falling back to index=off,metacopy=off.\n");
+			pr_warn("...falling back to index=off,metacopy=off.\n");
 		}
 		/*
 		 * xattr support is required for persistent st_ino.
@@ -1421,11 +1435,13 @@
 		 */
 		if (ofs->config.xino == OVL_XINO_AUTO) {
 			ofs->config.xino = OVL_XINO_OFF;
-			pr_warn("upper fs does not support xattr, falling back to xino=off.\n");
+			pr_warn("...falling back to xino=off.\n");
 		}
+		if (err == -EPERM && !ofs->config.userxattr)
+			pr_info("try mounting with 'userxattr' option\n");
 		err = 0;
 	} else {
-		ovl_do_removexattr(ofs, ofs->workdir, OVL_XATTR_OPAQUE);
+		ovl_removexattr(ofs, ofs->workdir, OVL_XATTR_OPAQUE);
 	}
 
 	/*
@@ -1952,7 +1968,7 @@
 	ovl_dentry_set_flag(OVL_E_CONNECTED, root);
 	ovl_set_upperdata(d_inode(root));
 	ovl_inode_init(d_inode(root), &oip, ino, fsid);
-	ovl_dentry_update_reval(root, upperdentry, DCACHE_OP_WEAK_REVALIDATE);
+	ovl_dentry_init_flags(root, upperdentry, DCACHE_OP_WEAK_REVALIDATE);
 
 	return root;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/overlayfs/util.c
+++ linux-xilinx-zynqmp-5.15.0/fs/overlayfs/util.c
@@ -94,14 +94,30 @@
 	return oe;
 }
 
+#define OVL_D_REVALIDATE (DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE)
+
 bool ovl_dentry_remote(struct dentry *dentry)
 {
-	return dentry->d_flags &
-		(DCACHE_OP_REVALIDATE | DCACHE_OP_WEAK_REVALIDATE);
+	return dentry->d_flags & OVL_D_REVALIDATE;
 }
 
-void ovl_dentry_update_reval(struct dentry *dentry, struct dentry *upperdentry,
-			     unsigned int mask)
+void ovl_dentry_update_reval(struct dentry *dentry, struct dentry *realdentry)
+{
+	if (!ovl_dentry_remote(realdentry))
+		return;
+
+	spin_lock(&dentry->d_lock);
+	dentry->d_flags |= realdentry->d_flags & OVL_D_REVALIDATE;
+	spin_unlock(&dentry->d_lock);
+}
+
+void ovl_dentry_init_reval(struct dentry *dentry, struct dentry *upperdentry)
+{
+	return ovl_dentry_init_flags(dentry, upperdentry, OVL_D_REVALIDATE);
+}
+
+void ovl_dentry_init_flags(struct dentry *dentry, struct dentry *upperdentry,
+			   unsigned int mask)
 {
 	struct ovl_entry *oe = OVL_E(dentry);
 	unsigned int i, flags = 0;
@@ -119,6 +135,9 @@
 
 bool ovl_dentry_weird(struct dentry *dentry)
 {
+	if (!d_can_lookup(dentry) && !d_is_file(dentry) && !d_is_symlink(dentry))
+		return true;
+
 	return dentry->d_flags & (DCACHE_NEED_AUTOMOUNT |
 				  DCACHE_MANAGE_TRANSIT |
 				  DCACHE_OP_HASH |
@@ -236,6 +255,17 @@
 	return ovl_upperdentry_dereference(OVL_I(inode));
 }
 
+void ovl_i_path_real(struct inode *inode, struct path *path)
+{
+	path->dentry = ovl_i_dentry_upper(inode);
+	if (!path->dentry) {
+		path->dentry = OVL_I(inode)->lowerpath.dentry;
+		path->mnt = OVL_I(inode)->lowerpath.layer->mnt;
+	} else {
+		path->mnt = ovl_upper_mnt(OVL_FS(inode->i_sb));
+	}
+}
+
 struct inode *ovl_inode_upper(struct inode *inode)
 {
 	struct dentry *upperdentry = ovl_i_dentry_upper(inode);
@@ -245,7 +275,9 @@
 
 struct inode *ovl_inode_lower(struct inode *inode)
 {
-	return OVL_I(inode)->lower;
+	struct dentry *lowerdentry = OVL_I(inode)->lowerpath.dentry;
+
+	return lowerdentry ? d_inode(lowerdentry) : NULL;
 }
 
 struct inode *ovl_inode_real(struct inode *inode)
@@ -443,7 +475,7 @@
 void ovl_dir_modified(struct dentry *dentry, bool impurity)
 {
 	/* Copy mtime/ctime */
-	ovl_copyattr(d_inode(ovl_dentry_upper(dentry)), d_inode(dentry));
+	ovl_copyattr(d_inode(dentry));
 
 	ovl_dir_version_inc(dentry, impurity);
 }
@@ -554,7 +586,7 @@
 {
 	int res;
 
-	res = ovl_do_getxattr(ofs, dentry, OVL_XATTR_ORIGIN, NULL, 0);
+	res = ovl_getxattr(ofs, dentry, OVL_XATTR_ORIGIN, NULL, 0);
 
 	/* Zero size value means "copied up but origin unknown" */
 	if (res >= 0)
@@ -572,7 +604,7 @@
 	if (!d_is_dir(dentry))
 		return false;
 
-	res = ovl_do_getxattr(OVL_FS(sb), dentry, ox, &val, 1);
+	res = ovl_getxattr(OVL_FS(sb), dentry, ox, &val, 1);
 	if (res == 1 && val == 'y')
 		return true;
 
@@ -612,7 +644,7 @@
 	if (ofs->noxattr)
 		return xerr;
 
-	err = ovl_do_setxattr(ofs, upperdentry, ox, value, size);
+	err = ovl_setxattr(ofs, upperdentry, ox, value, size);
 
 	if (err == -EOPNOTSUPP) {
 		pr_warn("cannot set %s xattr on upper\n", ovl_xattr(ofs, ox));
@@ -652,7 +684,7 @@
 	char buf[OVL_PROTATTR_MAX+1];
 	int res, n;
 
-	res = ovl_do_getxattr(ofs, upper, OVL_XATTR_PROTATTR, buf,
+	res = ovl_getxattr(ofs, upper, OVL_XATTR_PROTATTR, buf,
 			      OVL_PROTATTR_MAX);
 	if (res < 0)
 		return;
@@ -708,7 +740,7 @@
 		err = ovl_check_setxattr(ofs, upper, OVL_XATTR_PROTATTR,
 					 buf, len, -EPERM);
 	} else if (inode->i_flags & OVL_PROT_I_FLAGS_MASK) {
-		err = ovl_do_removexattr(ofs, upper, OVL_XATTR_PROTATTR);
+		err = ovl_removexattr(ofs, upper, OVL_XATTR_PROTATTR);
 		if (err == -EOPNOTSUPP || err == -ENODATA)
 			err = 0;
 	}
@@ -834,7 +866,7 @@
 					       dir, index);
 	} else {
 		/* Cleanup orphan index entries */
-		err = ovl_cleanup(dir, index);
+		err = ovl_cleanup(ofs, dir, index);
 	}
 
 	inode_unlock(dir);
@@ -951,7 +983,7 @@
 	if (!S_ISREG(d_inode(dentry)->i_mode))
 		return 0;
 
-	res = ovl_do_getxattr(ofs, dentry, OVL_XATTR_METACOPY, NULL, 0);
+	res = ovl_getxattr(ofs, dentry, OVL_XATTR_METACOPY, NULL, 0);
 	if (res < 0) {
 		if (res == -ENODATA || res == -EOPNOTSUPP)
 			return 0;
@@ -993,7 +1025,7 @@
 	int res;
 	char *s, *next, *buf = NULL;
 
-	res = ovl_do_getxattr(ofs, dentry, OVL_XATTR_REDIRECT, NULL, 0);
+	res = ovl_getxattr(ofs, dentry, OVL_XATTR_REDIRECT, NULL, 0);
 	if (res == -ENODATA || res == -EOPNOTSUPP)
 		return NULL;
 	if (res < 0)
@@ -1005,7 +1037,7 @@
 	if (!buf)
 		return ERR_PTR(-ENOMEM);
 
-	res = ovl_do_getxattr(ofs, dentry, OVL_XATTR_REDIRECT, buf, res);
+	res = ovl_getxattr(ofs, dentry, OVL_XATTR_REDIRECT, buf, res);
 	if (res < 0)
 		goto fail;
 	if (res == 0)
@@ -1060,3 +1092,33 @@
 
 	return errseq_check(&mnt->mnt_sb->s_wb_err, ofs->errseq);
 }
+
+/*
+ * ovl_copyattr() - copy inode attributes from layer to ovl inode
+ *
+ * When overlay copies inode information from an upper or lower layer to the
+ * relevant overlay inode it will apply the idmapping of the upper or lower
+ * layer when doing so ensuring that the ovl inode ownership will correctly
+ * reflect the ownership of the idmapped upper or lower layer. For example, an
+ * idmapped upper or lower layer mapping id 1001 to id 1000 will take care to
+ * map any lower or upper inode owned by id 1001 to id 1000. These mapping
+ * helpers are nops when the relevant layer isn't idmapped.
+ */
+void ovl_copyattr(struct inode *inode)
+{
+	struct path realpath;
+	struct inode *realinode;
+	struct user_namespace *real_mnt_userns;
+
+	ovl_i_path_real(inode, &realpath);
+	realinode = d_inode(realpath.dentry);
+	real_mnt_userns = mnt_user_ns(realpath.mnt);
+
+	inode->i_uid = i_uid_into_mnt(real_mnt_userns, realinode);
+	inode->i_gid = i_gid_into_mnt(real_mnt_userns, realinode);
+	inode->i_mode = realinode->i_mode;
+	inode->i_atime = realinode->i_atime;
+	inode->i_mtime = realinode->i_mtime;
+	inode->i_ctime = realinode->i_ctime;
+	i_size_write(inode, i_size_read(realinode));
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pipe.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pipe.c
@@ -252,7 +252,8 @@
 	 */
 	was_full = pipe_full(pipe->head, pipe->tail, pipe->max_usage);
 	for (;;) {
-		unsigned int head = pipe->head;
+		/* Read ->head with a barrier vs post_one_notification() */
+		unsigned int head = smp_load_acquire(&pipe->head);
 		unsigned int tail = pipe->tail;
 		unsigned int mask = pipe->ring_size - 1;
 
@@ -422,6 +423,18 @@
 	bool was_empty = false;
 	bool wake_next_writer = false;
 
+	/*
+	 * Reject writing to watch queue pipes before the point where we lock
+	 * the pipe.
+	 * Otherwise, lockdep would be unhappy if the caller already has another
+	 * pipe locked.
+	 * If we had to support locking a normal pipe and a notification pipe at
+	 * the same time, we could set up lockdep annotations for that, but
+	 * since we don't actually need that, it's simpler to just bail here.
+	 */
+	if (pipe_has_watch_queue(pipe))
+		return -EXDEV;
+
 	/* Null write succeeds. */
 	if (unlikely(total_len == 0))
 		return 0;
@@ -434,13 +447,6 @@
 		goto out;
 	}
 
-#ifdef CONFIG_WATCH_QUEUE
-	if (pipe->watch_queue) {
-		ret = -EXDEV;
-		goto out;
-	}
-#endif
-
 	/*
 	 * If it wasn't empty we try to merge new data into
 	 * the last buffer.
@@ -651,7 +657,7 @@
 	unsigned int head, tail;
 
 	/* Epoll has some historical nasty semantics, this enables them */
-	pipe->poll_usage = 1;
+	WRITE_ONCE(pipe->poll_usage, true);
 
 	/*
 	 * Reading pipe state only -- no need for acquiring the semaphore.
@@ -830,10 +836,8 @@
 	int i;
 
 #ifdef CONFIG_WATCH_QUEUE
-	if (pipe->watch_queue) {
+	if (pipe->watch_queue)
 		watch_queue_clear(pipe->watch_queue);
-		put_watch_queue(pipe->watch_queue);
-	}
 #endif
 
 	(void) account_pipe_buffers(pipe->user, pipe->nr_accounted, 0);
@@ -843,6 +847,10 @@
 		if (buf->ops)
 			pipe_buf_release(pipe, buf);
 	}
+#ifdef CONFIG_WATCH_QUEUE
+	if (pipe->watch_queue)
+		put_watch_queue(pipe->watch_queue);
+#endif
 	if (pipe->tmp_page)
 		__free_page(pipe->tmp_page);
 	kfree(pipe->bufs);
@@ -1241,30 +1249,33 @@
 
 /*
  * Resize the pipe ring to a number of slots.
+ *
+ * Note the pipe can be reduced in capacity, but only if the current
+ * occupancy doesn't exceed nr_slots; if it does, EBUSY will be
+ * returned instead.
  */
 int pipe_resize_ring(struct pipe_inode_info *pipe, unsigned int nr_slots)
 {
 	struct pipe_buffer *bufs;
 	unsigned int head, tail, mask, n;
 
-	/*
-	 * We can shrink the pipe, if arg is greater than the ring occupancy.
-	 * Since we don't expect a lot of shrink+grow operations, just free and
-	 * allocate again like we would do for growing.  If the pipe currently
-	 * contains more buffers than arg, then return busy.
-	 */
-	mask = pipe->ring_size - 1;
-	head = pipe->head;
-	tail = pipe->tail;
-	n = pipe_occupancy(pipe->head, pipe->tail);
-	if (nr_slots < n)
-		return -EBUSY;
-
 	bufs = kcalloc(nr_slots, sizeof(*bufs),
 		       GFP_KERNEL_ACCOUNT | __GFP_NOWARN);
 	if (unlikely(!bufs))
 		return -ENOMEM;
 
+	spin_lock_irq(&pipe->rd_wait.lock);
+	mask = pipe->ring_size - 1;
+	head = pipe->head;
+	tail = pipe->tail;
+
+	n = pipe_occupancy(head, tail);
+	if (nr_slots < n) {
+		spin_unlock_irq(&pipe->rd_wait.lock);
+		kfree(bufs);
+		return -EBUSY;
+	}
+
 	/*
 	 * The pipe array wraps around, so just start the new one at zero
 	 * and adjust the indices.
@@ -1296,6 +1307,13 @@
 	pipe->tail = tail;
 	pipe->head = head;
 
+	if (!pipe_has_watch_queue(pipe)) {
+		pipe->max_usage = nr_slots;
+		pipe->nr_accounted = nr_slots;
+	}
+
+	spin_unlock_irq(&pipe->rd_wait.lock);
+
 	/* This might have made more room for writers */
 	wake_up_interruptible(&pipe->wr_wait);
 	return 0;
@@ -1311,10 +1329,8 @@
 	unsigned int nr_slots, size;
 	long ret = 0;
 
-#ifdef CONFIG_WATCH_QUEUE
-	if (pipe->watch_queue)
+	if (pipe_has_watch_queue(pipe))
 		return -EBUSY;
-#endif
 
 	size = round_pipe_size(arg);
 	nr_slots = size >> PAGE_SHIFT;
@@ -1347,8 +1363,6 @@
 	if (ret < 0)
 		goto out_revert_acct;
 
-	pipe->max_usage = nr_slots;
-	pipe->nr_accounted = nr_slots;
 	return pipe->max_usage * PAGE_SIZE;
 
 out_revert_acct:
@@ -1366,10 +1380,8 @@
 
 	if (file->f_op != &pipefifo_fops || !pipe)
 		return NULL;
-#ifdef CONFIG_WATCH_QUEUE
-	if (for_splice && pipe->watch_queue)
+	if (for_splice && pipe_has_watch_queue(pipe))
 		return NULL;
-#endif
 	return pipe;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pnode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pnode.c
@@ -244,7 +244,7 @@
 		}
 		do {
 			struct mount *parent = last_source->mnt_parent;
-			if (last_source == first_source)
+			if (peers(last_source, first_source))
 				break;
 			done = parent->mnt_master == p;
 			if (done && peers(n, parent))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/posix_acl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/posix_acl.c
@@ -23,6 +23,7 @@
 #include <linux/export.h>
 #include <linux/user_namespace.h>
 #include <linux/namei.h>
+#include <linux/mnt_idmapping.h>
 
 static struct posix_acl **acl_by_type(struct inode *inode, int type)
 {
@@ -375,7 +376,9 @@
                                         goto check_perm;
                                 break;
                         case ACL_USER:
-				uid = kuid_into_mnt(mnt_userns, pa->e_uid);
+				uid = mapped_kuid_fs(mnt_userns,
+						     i_user_ns(inode),
+						     pa->e_uid);
 				if (uid_eq(uid, current_fsuid()))
                                         goto mask;
 				break;
@@ -388,7 +391,9 @@
                                 }
 				break;
                         case ACL_GROUP:
-				gid = kgid_into_mnt(mnt_userns, pa->e_gid);
+				gid = mapped_kgid_fs(mnt_userns,
+						     i_user_ns(inode),
+						     pa->e_gid);
 				if (in_group_p(gid)) {
 					found = 1;
 					if ((pa->e_perm & want) == want)
@@ -735,17 +740,17 @@
 		case ACL_USER:
 			uid = make_kuid(from, le32_to_cpu(entry->e_id));
 			if (from_user)
-				uid = kuid_from_mnt(mnt_userns, uid);
+				uid = mapped_kuid_user(mnt_userns, &init_user_ns, uid);
 			else
-				uid = kuid_into_mnt(mnt_userns, uid);
+				uid = mapped_kuid_fs(mnt_userns, &init_user_ns, uid);
 			entry->e_id = cpu_to_le32(from_kuid(to, uid));
 			break;
 		case ACL_GROUP:
 			gid = make_kgid(from, le32_to_cpu(entry->e_id));
 			if (from_user)
-				gid = kgid_from_mnt(mnt_userns, gid);
+				gid = mapped_kgid_user(mnt_userns, &init_user_ns, gid);
 			else
-				gid = kgid_into_mnt(mnt_userns, gid);
+				gid = mapped_kgid_fs(mnt_userns, &init_user_ns, gid);
 			entry->e_id = cpu_to_le32(from_kgid(to, gid));
 			break;
 		default:
@@ -755,9 +760,14 @@
 }
 
 void posix_acl_fix_xattr_from_user(struct user_namespace *mnt_userns,
+				   struct inode *inode,
 				   void *value, size_t size)
 {
 	struct user_namespace *user_ns = current_user_ns();
+
+	/* Leave ids untouched on non-idmapped mounts. */
+	if (no_idmapping(mnt_userns, i_user_ns(inode)))
+		mnt_userns = &init_user_ns;
 	if ((user_ns == &init_user_ns) && (mnt_userns == &init_user_ns))
 		return;
 	posix_acl_fix_xattr_userns(&init_user_ns, user_ns, mnt_userns, value,
@@ -765,9 +775,14 @@
 }
 
 void posix_acl_fix_xattr_to_user(struct user_namespace *mnt_userns,
+				 struct inode *inode,
 				 void *value, size_t size)
 {
 	struct user_namespace *user_ns = current_user_ns();
+
+	/* Leave ids untouched on non-idmapped mounts. */
+	if (no_idmapping(mnt_userns, i_user_ns(inode)))
+		mnt_userns = &init_user_ns;
 	if ((user_ns == &init_user_ns) && (mnt_userns == &init_user_ns))
 		return;
 	posix_acl_fix_xattr_userns(user_ns, &init_user_ns, mnt_userns, value,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/Makefile
@@ -33,4 +33,4 @@
 proc-$(CONFIG_PROC_VMCORE)	+= vmcore.o
 proc-$(CONFIG_PRINTK)	+= kmsg.o
 proc-$(CONFIG_PROC_PAGE_MONITOR)	+= page.o
-proc-$(CONFIG_BOOT_CONFIG)	+= bootconfig.o
+proc-$(CONFIG_BOOT_CONFIG)	+= bootconfig.o version_signature.o
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/array.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/array.c
@@ -495,7 +495,7 @@
 
 	sigemptyset(&sigign);
 	sigemptyset(&sigcatch);
-	cutime = cstime = utime = stime = 0;
+	cutime = cstime = 0;
 	cgtime = gtime = 0;
 
 	if (lock_task_sighand(task, &flags)) {
@@ -529,7 +529,6 @@
 
 			min_flt += sig->min_flt;
 			maj_flt += sig->maj_flt;
-			thread_group_cputime_adjusted(task, &utime, &stime);
 			gtime += sig->gtime;
 		}
 
@@ -541,11 +540,14 @@
 	}
 
 	if (permitted && (!whole || num_threads < 2))
-		wchan = get_wchan(task);
-	if (!whole) {
+		wchan = !task_is_running(task);
+
+	if (whole) {
+		thread_group_cputime_adjusted(task, &utime, &stime);
+	} else {
+		task_cputime_adjusted(task, &utime, &stime);
 		min_flt = task->min_flt;
 		maj_flt = task->maj_flt;
-		task_cputime_adjusted(task, &utime, &stime);
 		gtime = task_gtime(task);
 	}
 
@@ -606,10 +608,7 @@
 	 *
 	 * This works with older implementations of procps as well.
 	 */
-	if (wchan)
-		seq_puts(m, " 1");
-	else
-		seq_puts(m, " 0");
+	seq_put_decimal_ull(m, " ", wchan);
 
 	seq_put_decimal_ull(m, " ", 0);
 	seq_put_decimal_ull(m, " ", 0);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/base.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/base.c
@@ -67,6 +67,7 @@
 #include <linux/mm.h>
 #include <linux/swap.h>
 #include <linux/rcupdate.h>
+#include <linux/kallsyms.h>
 #include <linux/stacktrace.h>
 #include <linux/resource.h>
 #include <linux/module.h>
@@ -85,6 +86,7 @@
 #include <linux/elf.h>
 #include <linux/pid_namespace.h>
 #include <linux/user_namespace.h>
+#include <linux/fs_parser.h>
 #include <linux/fs_struct.h>
 #include <linux/slab.h>
 #include <linux/sched/autogroup.h>
@@ -115,6 +117,40 @@
 static u8 nlink_tid __ro_after_init;
 static u8 nlink_tgid __ro_after_init;
 
+enum proc_mem_force {
+	PROC_MEM_FORCE_ALWAYS,
+	PROC_MEM_FORCE_PTRACE,
+	PROC_MEM_FORCE_NEVER
+};
+
+static enum proc_mem_force proc_mem_force_override __ro_after_init =
+	IS_ENABLED(CONFIG_PROC_MEM_NO_FORCE) ? PROC_MEM_FORCE_NEVER :
+	IS_ENABLED(CONFIG_PROC_MEM_FORCE_PTRACE) ? PROC_MEM_FORCE_PTRACE :
+	PROC_MEM_FORCE_ALWAYS;
+
+static const struct constant_table proc_mem_force_table[] __initconst = {
+	{ "always", PROC_MEM_FORCE_ALWAYS },
+	{ "ptrace", PROC_MEM_FORCE_PTRACE },
+	{ "never", PROC_MEM_FORCE_NEVER },
+	{ }
+};
+
+static int __init early_proc_mem_force_override(char *buf)
+{
+	if (!buf)
+		return -EINVAL;
+
+	/*
+	 * lookup_constant() defaults to proc_mem_force_override to preseve
+	 * the initial Kconfig choice in case an invalid param gets passed.
+	 */
+	proc_mem_force_override = lookup_constant(proc_mem_force_table,
+						  buf, proc_mem_force_override);
+
+	return 0;
+}
+early_param("proc_mem.force_override", early_proc_mem_force_override);
+
 struct pid_entry {
 	const char *name;
 	unsigned int len;
@@ -380,23 +416,25 @@
 #ifdef CONFIG_KALLSYMS
 /*
  * Provides a wchan file via kallsyms in a proper one-value-per-file format.
- * Returns the resolved symbol.  If that fails, simply return the address.
+ * Returns the resolved symbol to user space.
  */
 static int proc_pid_wchan(struct seq_file *m, struct pid_namespace *ns,
 			  struct pid *pid, struct task_struct *task)
 {
 	unsigned long wchan;
+	char symname[KSYM_NAME_LEN];
 
-	if (ptrace_may_access(task, PTRACE_MODE_READ_FSCREDS))
-		wchan = get_wchan(task);
-	else
-		wchan = 0;
+	if (!ptrace_may_access(task, PTRACE_MODE_READ_FSCREDS))
+		goto print0;
 
-	if (wchan)
-		seq_printf(m, "%ps", (void *) wchan);
-	else
-		seq_putc(m, '0');
+	wchan = get_wchan(task);
+	if (wchan && !lookup_symbol_name(wchan, symname)) {
+		seq_puts(m, symname);
+		return 0;
+	}
 
+print0:
+	seq_putc(m, '0');
 	return 0;
 }
 #endif /* CONFIG_KALLSYMS */
@@ -832,6 +870,28 @@
 	return ret;
 }
 
+static bool proc_mem_foll_force(struct file *file, struct mm_struct *mm)
+{
+	struct task_struct *task;
+	bool ptrace_active = false;
+
+	switch (proc_mem_force_override) {
+	case PROC_MEM_FORCE_NEVER:
+		return false;
+	case PROC_MEM_FORCE_PTRACE:
+		task = get_proc_task(file_inode(file));
+		if (task) {
+			ptrace_active =	READ_ONCE(task->ptrace) &&
+					READ_ONCE(task->mm) == mm &&
+					READ_ONCE(task->parent) == current;
+			put_task_struct(task);
+		}
+		return ptrace_active;
+	default:
+		return true;
+	}
+}
+
 static ssize_t mem_rw(struct file *file, char __user *buf,
 			size_t count, loff_t *ppos, int write)
 {
@@ -852,7 +912,9 @@
 	if (!mmget_not_zero(mm))
 		goto free;
 
-	flags = FOLL_FORCE | (write ? FOLL_WRITE : 0);
+	flags = write ? FOLL_WRITE : 0;
+	if (proc_mem_foll_force(file, mm))
+		flags |= FOLL_FORCE;
 
 	while (count > 0) {
 		size_t this_len = min_t(size_t, count, PAGE_SIZE);
@@ -1883,7 +1945,7 @@
 	put_pid(pid);
 }
 
-struct inode *proc_pid_make_inode(struct super_block * sb,
+struct inode *proc_pid_make_inode(struct super_block *sb,
 				  struct task_struct *task, umode_t mode)
 {
 	struct inode * inode;
@@ -1912,11 +1974,6 @@
 
 	/* Let the pid remember us for quick removal */
 	ei->pid = pid;
-	if (S_ISDIR(mode)) {
-		spin_lock(&pid->lock);
-		hlist_add_head_rcu(&ei->sibling_inodes, &pid->inodes);
-		spin_unlock(&pid->lock);
-	}
 
 	task_dump_owner(task, 0, &inode->i_uid, &inode->i_gid);
 	security_task_to_inode(task, inode);
@@ -1929,6 +1986,39 @@
 	return NULL;
 }
 
+/*
+ * Generating an inode and adding it into @pid->inodes, so that task will
+ * invalidate inode's dentry before being released.
+ *
+ * This helper is used for creating dir-type entries under '/proc' and
+ * '/proc/<tgid>/task'. Other entries(eg. fd, stat) under '/proc/<tgid>'
+ * can be released by invalidating '/proc/<tgid>' dentry.
+ * In theory, dentries under '/proc/<tgid>/task' can also be released by
+ * invalidating '/proc/<tgid>' dentry, we reserve it to handle single
+ * thread exiting situation: Any one of threads should invalidate its
+ * '/proc/<tgid>/task/<pid>' dentry before released.
+ */
+static struct inode *proc_pid_make_base_inode(struct super_block *sb,
+				struct task_struct *task, umode_t mode)
+{
+	struct inode *inode;
+	struct proc_inode *ei;
+	struct pid *pid;
+
+	inode = proc_pid_make_inode(sb, task, mode);
+	if (!inode)
+		return NULL;
+
+	/* Let proc_flush_pid find this directory inode */
+	ei = PROC_I(inode);
+	pid = ei->pid;
+	spin_lock(&pid->lock);
+	hlist_add_head_rcu(&ei->sibling_inodes, &pid->inodes);
+	spin_unlock(&pid->lock);
+
+	return inode;
+}
+
 int pid_getattr(struct user_namespace *mnt_userns, const struct path *path,
 		struct kstat *stat, u32 request_mask, unsigned int query_flags)
 {
@@ -2186,7 +2276,7 @@
 	rc = -ENOENT;
 	vma = find_exact_vma(mm, vm_start, vm_end);
 	if (vma && vma->vm_file) {
-		*path = vma->vm_file->f_path;
+		*path = vma_pr_or_file(vma)->f_path;
 		path_get(path);
 		rc = 0;
 	}
@@ -2823,6 +2913,8 @@
 	ATTR(NULL, "fscreate",		0666),
 	ATTR(NULL, "keycreate",		0666),
 	ATTR(NULL, "sockcreate",	0666),
+	ATTR(NULL, "display",		0666),
+	ATTR(NULL, "context",		0444),
 #ifdef CONFIG_SECURITY_SMACK
 	DIR("smack",			0555,
 	    proc_smack_attr_dir_inode_ops, proc_smack_attr_dir_ops),
@@ -3346,7 +3438,8 @@
 {
 	struct inode *inode;
 
-	inode = proc_pid_make_inode(dentry->d_sb, task, S_IFDIR | S_IRUGO | S_IXUGO);
+	inode = proc_pid_make_base_inode(dentry->d_sb, task,
+					 S_IFDIR | S_IRUGO | S_IXUGO);
 	if (!inode)
 		return ERR_PTR(-ENOENT);
 
@@ -3512,7 +3605,8 @@
 }
 
 static const struct inode_operations proc_tid_comm_inode_operations = {
-		.permission = proc_tid_comm_permission,
+		.setattr	= proc_setattr,
+		.permission	= proc_tid_comm_permission,
 };
 
 /*
@@ -3645,7 +3739,8 @@
 	struct task_struct *task, const void *ptr)
 {
 	struct inode *inode;
-	inode = proc_pid_make_inode(dentry->d_sb, task, S_IFDIR | S_IRUGO | S_IXUGO);
+	inode = proc_pid_make_base_inode(dentry->d_sb, task,
+					 S_IFDIR | S_IRUGO | S_IXUGO);
 	if (!inode)
 		return ERR_PTR(-ENOENT);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/bootconfig.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/bootconfig.c
@@ -32,6 +32,8 @@
 	int ret = 0;
 
 	key = kzalloc(XBC_KEYLEN_MAX, GFP_KERNEL);
+	if (!key)
+		return -ENOMEM;
 
 	xbc_for_each_key_value(leaf, val) {
 		ret = xbc_node_compose_key(leaf, key, XBC_KEYLEN_MAX);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/fd.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/fd.c
@@ -72,7 +72,7 @@
 	return 0;
 }
 
-static int seq_fdinfo_open(struct inode *inode, struct file *file)
+static int proc_fdinfo_access_allowed(struct inode *inode)
 {
 	bool allowed = false;
 	struct task_struct *task = get_proc_task(inode);
@@ -86,6 +86,16 @@
 	if (!allowed)
 		return -EACCES;
 
+	return 0;
+}
+
+static int seq_fdinfo_open(struct inode *inode, struct file *file)
+{
+	int ret = proc_fdinfo_access_allowed(inode);
+
+	if (ret)
+		return ret;
+
 	return single_open(file, seq_show, inode);
 }
 
@@ -348,12 +358,23 @@
 				  proc_fdinfo_instantiate);
 }
 
+static int proc_open_fdinfo(struct inode *inode, struct file *file)
+{
+	int ret = proc_fdinfo_access_allowed(inode);
+
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
 const struct inode_operations proc_fdinfo_inode_operations = {
 	.lookup		= proc_lookupfdinfo,
 	.setattr	= proc_setattr,
 };
 
 const struct file_operations proc_fdinfo_operations = {
+	.open		= proc_open_fdinfo,
 	.read		= generic_read_dir,
 	.iterate_shared	= proc_readfdinfo,
 	.llseek		= generic_file_llseek,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/generic.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/generic.c
@@ -448,6 +448,9 @@
 	proc_set_user(ent, (*parent)->uid, (*parent)->gid);
 
 	ent->proc_dops = &proc_misc_dentry_ops;
+	/* Revalidate everything under /proc/${pid}/net */
+	if ((*parent)->proc_dops == &proc_net_dentry_ops)
+		pde_force_lookup(ent);
 
 out:
 	return ent;
@@ -555,10 +558,16 @@
 	return p;
 }
 
-static inline void pde_set_flags(struct proc_dir_entry *pde)
+static void pde_set_flags(struct proc_dir_entry *pde)
 {
 	if (pde->proc_ops->proc_flags & PROC_ENTRY_PERMANENT)
 		pde->flags |= PROC_ENTRY_PERMANENT;
+	if (pde->proc_ops->proc_read_iter)
+		pde->flags |= PROC_ENTRY_proc_read_iter;
+#ifdef CONFIG_COMPAT
+	if (pde->proc_ops->proc_compat_ioctl)
+		pde->flags |= PROC_ENTRY_proc_compat_ioctl;
+#endif
 }
 
 struct proc_dir_entry *proc_create_data(const char *name, umode_t mode,
@@ -622,6 +631,7 @@
 	p->proc_ops = &proc_seq_ops;
 	p->seq_ops = ops;
 	p->state_size = state_size;
+	pde_set_flags(p);
 	return proc_register(parent, p);
 }
 EXPORT_SYMBOL(proc_create_seq_private);
@@ -652,6 +662,7 @@
 		return NULL;
 	p->proc_ops = &proc_single_ops;
 	p->single_show = show;
+	pde_set_flags(p);
 	return proc_register(parent, p);
 }
 EXPORT_SYMBOL(proc_create_single_data);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/inode.c
@@ -670,13 +670,13 @@
 
 	if (S_ISREG(inode->i_mode)) {
 		inode->i_op = de->proc_iops;
-		if (de->proc_ops->proc_read_iter)
+		if (pde_has_proc_read_iter(de))
 			inode->i_fop = &proc_iter_file_ops;
 		else
 			inode->i_fop = &proc_reg_file_ops;
 #ifdef CONFIG_COMPAT
-		if (de->proc_ops->proc_compat_ioctl) {
-			if (de->proc_ops->proc_read_iter)
+		if (pde_has_proc_compat_ioctl(de)) {
+			if (pde_has_proc_read_iter(de))
 				inode->i_fop = &proc_iter_file_ops_compat;
 			else
 				inode->i_fop = &proc_reg_file_ops_compat;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/internal.h
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/internal.h
@@ -79,6 +79,20 @@
 	return pde->flags & PROC_ENTRY_PERMANENT;
 }
 
+static inline bool pde_has_proc_read_iter(const struct proc_dir_entry *pde)
+{
+	return pde->flags & PROC_ENTRY_proc_read_iter;
+}
+
+static inline bool pde_has_proc_compat_ioctl(const struct proc_dir_entry *pde)
+{
+#ifdef CONFIG_COMPAT
+	return pde->flags & PROC_ENTRY_proc_compat_ioctl;
+#else
+	return false;
+#endif
+}
+
 extern struct kmem_cache *proc_dir_entry_cache;
 void pde_free(struct proc_dir_entry *pde);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/nommu.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/nommu.c
@@ -40,7 +40,10 @@
 	file = region->vm_file;
 
 	if (file) {
-		struct inode *inode = file_inode(region->vm_file);
+		struct inode *inode;
+
+		file = vmr_pr_or_file(region);
+		inode = file_inode(file);
 		dev = inode->i_sb->s_dev;
 		ino = inode->i_ino;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/proc_net.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/proc_net.c
@@ -363,6 +363,9 @@
 
 	proc_set_user(netd, uid, gid);
 
+	/* Seed dentry revalidation for /proc/${pid}/net */
+	pde_force_lookup(netd);
+
 	err = -EEXIST;
 	net_statd = proc_net_mkdir(net, "stat", netd);
 	if (!net_statd)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/proc_sysctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/proc_sysctl.c
@@ -16,6 +16,7 @@
 #include <linux/module.h>
 #include <linux/bpf-cgroup.h>
 #include <linux/mount.h>
+#include <linux/kmemleak.h>
 #include "internal.h"
 
 static const struct dentry_operations proc_sys_dentry_operations;
@@ -25,9 +26,12 @@
 static const struct inode_operations proc_sys_dir_operations;
 
 /* shared constants to be used in various sysctls */
-const int sysctl_vals[] = { 0, 1, INT_MAX };
+const int sysctl_vals[] = { -1, 0, 1, 2, 4, 100, 200, 1000, 3000, INT_MAX };
 EXPORT_SYMBOL(sysctl_vals);
 
+const unsigned long sysctl_long_vals[] = { 0, 1, LONG_MAX };
+EXPORT_SYMBOL_GPL(sysctl_long_vals);
+
 /* Support for permanently empty directories */
 
 struct ctl_table sysctl_mount_point[] = {
@@ -465,12 +469,10 @@
 			make_empty_dir_inode(inode);
 	}
 
+	inode->i_uid = GLOBAL_ROOT_UID;
+	inode->i_gid = GLOBAL_ROOT_GID;
 	if (root->set_ownership)
 		root->set_ownership(head, table, &inode->i_uid, &inode->i_gid);
-	else {
-		inode->i_uid = GLOBAL_ROOT_UID;
-		inode->i_gid = GLOBAL_ROOT_GID;
-	}
 
 	return inode;
 }
@@ -1384,6 +1386,38 @@
 }
 EXPORT_SYMBOL(register_sysctl);
 
+/**
+ * __register_sysctl_init() - register sysctl table to path
+ * @path: path name for sysctl base
+ * @table: This is the sysctl table that needs to be registered to the path
+ * @table_name: The name of sysctl table, only used for log printing when
+ *              registration fails
+ *
+ * The sysctl interface is used by userspace to query or modify at runtime
+ * a predefined value set on a variable. These variables however have default
+ * values pre-set. Code which depends on these variables will always work even
+ * if register_sysctl() fails. If register_sysctl() fails you'd just loose the
+ * ability to query or modify the sysctls dynamically at run time. Chances of
+ * register_sysctl() failing on init are extremely low, and so for both reasons
+ * this function does not return any error as it is used by initialization code.
+ *
+ * Context: Can only be called after your respective sysctl base path has been
+ * registered. So for instance, most base directories are registered early on
+ * init before init levels are processed through proc_sys_init() and
+ * sysctl_init().
+ */
+void __init __register_sysctl_init(const char *path, struct ctl_table *table,
+				 const char *table_name)
+{
+	struct ctl_table_header *hdr = register_sysctl(path, table);
+
+	if (unlikely(!hdr)) {
+		pr_err("failed when register_sysctl %s to %s\n", table_name, path);
+		return;
+	}
+	kmemleak_not_leak(hdr);
+}
+
 static char *append_path(const char *path, char *pos, const char *name)
 {
 	int namelen;
@@ -1732,7 +1766,6 @@
 	{"hung_task_panic",			"kernel.hung_task_panic" },
 	{"numa_zonelist_order",			"vm.numa_zonelist_order" },
 	{"softlockup_all_cpu_backtrace",	"kernel.softlockup_all_cpu_backtrace" },
-	{"softlockup_panic",			"kernel.softlockup_panic" },
 	{ }
 };
 
@@ -1748,6 +1781,13 @@
 	return NULL;
 }
 
+bool sysctl_is_alias(char *param)
+{
+	const char *alias = sysctl_find_alias(param);
+
+	return alias != NULL;
+}
+
 /* Set sysctl value passed on kernel command line. */
 static int process_sysctl_arg(char *param, char *val,
 			       const char *unused, void *arg)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/softirqs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/softirqs.c
@@ -19,7 +19,7 @@
 	for (i = 0; i < NR_SOFTIRQS; i++) {
 		seq_printf(p, "%12s:", softirq_to_name[i]);
 		for_each_possible_cpu(j)
-			seq_printf(p, " %10u", kstat_softirqs_cpu(i, j));
+			seq_put_decimal_ull_width(p, " ", kstat_softirqs_cpu(i, j), 10);
 		seq_putc(p, '\n');
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/stat.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/stat.c
@@ -24,7 +24,7 @@
 
 #ifdef arch_idle_time
 
-static u64 get_idle_time(struct kernel_cpustat *kcs, int cpu)
+u64 get_idle_time(struct kernel_cpustat *kcs, int cpu)
 {
 	u64 idle;
 
@@ -46,7 +46,7 @@
 
 #else
 
-static u64 get_idle_time(struct kernel_cpustat *kcs, int cpu)
+u64 get_idle_time(struct kernel_cpustat *kcs, int cpu)
 {
 	u64 idle, idle_usecs = -1ULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/task_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/task_mmu.c
@@ -280,7 +280,10 @@
 	const char *name = NULL;
 
 	if (file) {
-		struct inode *inode = file_inode(vma->vm_file);
+		struct inode *inode;
+
+		file = vma_pr_or_file(vma);
+		inode = file_inode(file);
 		dev = inode->i_sb->s_dev;
 		ino = inode->i_ino;
 		pgoff = ((loff_t)vma->vm_pgoff) << PAGE_SHIFT;
@@ -430,7 +433,8 @@
 }
 
 static void smaps_account(struct mem_size_stats *mss, struct page *page,
-		bool compound, bool young, bool dirty, bool locked)
+		bool compound, bool young, bool dirty, bool locked,
+		bool migration)
 {
 	int i, nr = compound ? compound_nr(page) : 1;
 	unsigned long size = nr * PAGE_SIZE;
@@ -457,8 +461,15 @@
 	 * page_count(page) == 1 guarantees the page is mapped exactly once.
 	 * If any subpage of the compound page mapped with PTE it would elevate
 	 * page_count().
+	 *
+	 * The page_mapcount() is called to get a snapshot of the mapcount.
+	 * Without holding the page lock this snapshot can be slightly wrong as
+	 * we cannot always read the mapcount atomically.  It is not safe to
+	 * call page_mapcount() even with PTL held if the page is not mapped,
+	 * especially for migration entries.  Treat regular migration entries
+	 * as mapcount == 1.
 	 */
-	if (page_count(page) == 1) {
+	if ((page_count(page) == 1) || migration) {
 		smaps_page_accumulate(mss, page, size, size << PSS_SHIFT, dirty,
 			locked, true);
 		return;
@@ -495,9 +506,12 @@
 	struct vm_area_struct *vma = walk->vma;
 	bool locked = !!(vma->vm_flags & VM_LOCKED);
 	struct page *page = NULL;
+	bool migration = false, young = false, dirty = false;
 
 	if (pte_present(*pte)) {
 		page = vm_normal_page(vma, addr, *pte);
+		young = pte_young(*pte);
+		dirty = pte_dirty(*pte);
 	} else if (is_swap_pte(*pte)) {
 		swp_entry_t swpent = pte_to_swp_entry(*pte);
 
@@ -514,8 +528,11 @@
 			} else {
 				mss->swap_pss += (u64)PAGE_SIZE << PSS_SHIFT;
 			}
-		} else if (is_pfn_swap_entry(swpent))
+		} else if (is_pfn_swap_entry(swpent)) {
+			if (is_migration_entry(swpent))
+				migration = true;
 			page = pfn_swap_entry_to_page(swpent);
+		}
 	} else if (unlikely(IS_ENABLED(CONFIG_SHMEM) && mss->check_shmem_swap
 							&& pte_none(*pte))) {
 		page = xa_load(&vma->vm_file->f_mapping->i_pages,
@@ -528,7 +545,7 @@
 	if (!page)
 		return;
 
-	smaps_account(mss, page, false, pte_young(*pte), pte_dirty(*pte), locked);
+	smaps_account(mss, page, false, young, dirty, locked, migration);
 }
 
 #ifdef CONFIG_TRANSPARENT_HUGEPAGE
@@ -539,6 +556,7 @@
 	struct vm_area_struct *vma = walk->vma;
 	bool locked = !!(vma->vm_flags & VM_LOCKED);
 	struct page *page = NULL;
+	bool migration = false;
 
 	if (pmd_present(*pmd)) {
 		/* FOLL_DUMP will return -EFAULT on huge zero page */
@@ -546,8 +564,10 @@
 	} else if (unlikely(thp_migration_supported() && is_swap_pmd(*pmd))) {
 		swp_entry_t entry = pmd_to_swp_entry(*pmd);
 
-		if (is_migration_entry(entry))
+		if (is_migration_entry(entry)) {
+			migration = true;
 			page = pfn_swap_entry_to_page(entry);
+		}
 	}
 	if (IS_ERR_OR_NULL(page))
 		return;
@@ -559,7 +579,9 @@
 		/* pass */;
 	else
 		mss->file_thp += HPAGE_PMD_SIZE;
-	smaps_account(mss, page, true, pmd_young(*pmd), pmd_dirty(*pmd), locked);
+
+	smaps_account(mss, page, true, pmd_young(*pmd), pmd_dirty(*pmd),
+		      locked, migration);
 }
 #else
 static void smaps_pmd_entry(pmd_t *pmd, unsigned long addr,
@@ -695,9 +717,7 @@
 			page = pfn_swap_entry_to_page(swpent);
 	}
 	if (page) {
-		int mapcount = page_mapcount(page);
-
-		if (mapcount >= 2)
+		if (page_mapcount(page) >= 2 || hugetlb_pmd_shared(pte))
 			mss->shared_hugetlb += huge_page_size(hstate_vma(vma));
 		else
 			mss->private_hugetlb += huge_page_size(hstate_vma(vma));
@@ -932,7 +952,7 @@
 		vma = vma->vm_next;
 	}
 
-	show_vma_header_prefix(m, priv->mm->mmap->vm_start,
+	show_vma_header_prefix(m, priv->mm->mmap ? priv->mm->mmap->vm_start : 0,
 			       last_vma_end, 0, 0, 0, 0);
 	seq_pad(m, ' ');
 	seq_puts(m, "[rollup]\n");
@@ -1363,6 +1383,7 @@
 {
 	u64 frame = 0, flags = 0;
 	struct page *page = NULL;
+	bool migration = false;
 
 	if (pte_present(pte)) {
 		if (pm->show_pfn)
@@ -1384,13 +1405,14 @@
 			frame = swp_type(entry) |
 				(swp_offset(entry) << MAX_SWAPFILES_SHIFT);
 		flags |= PM_SWAP;
+		migration = is_migration_entry(entry);
 		if (is_pfn_swap_entry(entry))
 			page = pfn_swap_entry_to_page(entry);
 	}
 
 	if (page && !PageAnon(page))
 		flags |= PM_FILE;
-	if (page && page_mapcount(page) == 1)
+	if (page && !migration && page_mapcount(page) == 1)
 		flags |= PM_MMAP_EXCLUSIVE;
 	if (vma->vm_flags & VM_SOFTDIRTY)
 		flags |= PM_SOFT_DIRTY;
@@ -1406,8 +1428,9 @@
 	spinlock_t *ptl;
 	pte_t *pte, *orig_pte;
 	int err = 0;
-
 #ifdef CONFIG_TRANSPARENT_HUGEPAGE
+	bool migration = false;
+
 	ptl = pmd_trans_huge_lock(pmdp, vma);
 	if (ptl) {
 		u64 flags = 0, frame = 0;
@@ -1446,11 +1469,14 @@
 			if (pmd_swp_uffd_wp(pmd))
 				flags |= PM_UFFD_WP;
 			VM_BUG_ON(!is_pmd_migration_entry(pmd));
+			migration = is_migration_entry(entry);
 			page = pfn_swap_entry_to_page(entry);
 		}
 #endif
 
-		if (page && page_mapcount(page) == 1)
+		if (page && !PageAnon(page))
+			flags |= PM_FILE;
+		if (page && !migration && page_mapcount(page) == 1)
 			flags |= PM_MMAP_EXCLUSIVE;
 
 		for (; addr != end; addr += PAGE_SIZE) {
@@ -1560,7 +1586,8 @@
  * Bits 5-54  swap offset if swapped
  * Bit  55    pte is soft-dirty (see Documentation/admin-guide/mm/soft-dirty.rst)
  * Bit  56    page exclusively mapped
- * Bits 57-60 zero
+ * Bit  57    pte is uffd-wp write-protected
+ * Bits 58-60 zero
  * Bit  61    page is file-page or shared-anon
  * Bit  62    page swapped
  * Bit  63    page present
@@ -1865,7 +1892,7 @@
 	struct proc_maps_private *proc_priv = &numa_priv->proc_maps;
 	struct vm_area_struct *vma = v;
 	struct numa_maps *md = &numa_priv->md;
-	struct file *file = vma->vm_file;
+	struct file *file = vma_pr_or_file(vma);
 	struct mm_struct *mm = vma->vm_mm;
 	struct mempolicy *pol;
 	char buffer[64];
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/task_nommu.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/task_nommu.c
@@ -155,7 +155,10 @@
 	file = vma->vm_file;
 
 	if (file) {
-		struct inode *inode = file_inode(vma->vm_file);
+		struct inode *inode;
+
+		file = vma_pr_or_file(vma);
+		inode = file_inode(file);
 		dev = inode->i_sb->s_dev;
 		ino = inode->i_ino;
 		pgoff = (loff_t)vma->vm_pgoff << PAGE_SHIFT;
@@ -208,11 +211,16 @@
 		return ERR_PTR(-ESRCH);
 
 	mm = priv->mm;
-	if (!mm || !mmget_not_zero(mm))
+	if (!mm || !mmget_not_zero(mm)) {
+		put_task_struct(priv->task);
+		priv->task = NULL;
 		return NULL;
+	}
 
 	if (mmap_read_lock_killable(mm)) {
 		mmput(mm);
+		put_task_struct(priv->task);
+		priv->task = NULL;
 		return ERR_PTR(-EINTR);
 	}
 
@@ -221,23 +229,21 @@
 		if (n-- == 0)
 			return p;
 
-	mmap_read_unlock(mm);
-	mmput(mm);
 	return NULL;
 }
 
-static void m_stop(struct seq_file *m, void *_vml)
+static void m_stop(struct seq_file *m, void *v)
 {
 	struct proc_maps_private *priv = m->private;
+	struct mm_struct *mm = priv->mm;
 
-	if (!IS_ERR_OR_NULL(_vml)) {
-		mmap_read_unlock(priv->mm);
-		mmput(priv->mm);
-	}
-	if (priv->task) {
-		put_task_struct(priv->task);
-		priv->task = NULL;
-	}
+	if (!priv->task)
+		return;
+
+	mmap_read_unlock(mm);
+	mmput(mm);
+	put_task_struct(priv->task);
+	priv->task = NULL;
 }
 
 static void *m_next(struct seq_file *m, void *_p, loff_t *pos)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/uptime.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/uptime.c
@@ -12,18 +12,22 @@
 {
 	struct timespec64 uptime;
 	struct timespec64 idle;
-	u64 nsec;
+	u64 idle_nsec;
 	u32 rem;
 	int i;
 
-	nsec = 0;
-	for_each_possible_cpu(i)
-		nsec += (__force u64) kcpustat_cpu(i).cpustat[CPUTIME_IDLE];
+	idle_nsec = 0;
+	for_each_possible_cpu(i) {
+		struct kernel_cpustat kcs;
+
+		kcpustat_cpu_fetch(&kcs, i);
+		idle_nsec += get_idle_time(&kcs, i);
+	}
 
 	ktime_get_boottime_ts64(&uptime);
 	timens_add_boottime(&uptime);
 
-	idle.tv_sec = div_u64_rem(nsec, NSEC_PER_SEC, &rem);
+	idle.tv_sec = div_u64_rem(idle_nsec, NSEC_PER_SEC, &rem);
 	idle.tv_nsec = rem;
 	seq_printf(m, "%lu.%02lu %lu.%02lu\n",
 			(unsigned long) uptime.tv_sec,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/version_signature.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/version_signature.c
@@ -0,0 +1,32 @@
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
+#include <linux/utsname.h>
+
+static int version_signature_proc_show(struct seq_file *m, void *v)
+{
+	seq_printf(m, "%s\n", CONFIG_VERSION_SIGNATURE);
+	return 0;
+}
+
+static int version_signature_proc_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, version_signature_proc_show, NULL);
+}
+
+static const struct proc_ops version_signature_proc_fops = {
+	.proc_open	= version_signature_proc_open,
+	.proc_read	= seq_read,
+	.proc_lseek	= seq_lseek,
+	.proc_release	= single_release,
+};
+
+static int __init proc_version_signature_init(void)
+{
+	proc_create("version_signature", 0, NULL, &version_signature_proc_fops);
+	return 0;
+}
+module_init(proc_version_signature_init);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc/vmcore.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc/vmcore.c
@@ -124,9 +124,13 @@
 			nr_bytes = count;
 
 		/* If pfn is not ram, return zeros for sparse dump files */
-		if (pfn_is_ram(pfn) == 0)
-			memset(buf, 0, nr_bytes);
-		else {
+		if (pfn_is_ram(pfn) == 0) {
+			tmp = 0;
+			if (!userbuf)
+				memset(buf, 0, nr_bytes);
+			else if (clear_user(buf, nr_bytes))
+				tmp = -EFAULT;
+		} else {
 			if (encrypted)
 				tmp = copy_oldmem_page_encrypted(pfn, buf,
 								 nr_bytes,
@@ -135,10 +139,10 @@
 			else
 				tmp = copy_oldmem_page(pfn, buf, nr_bytes,
 						       offset, userbuf);
-
-			if (tmp < 0)
-				return tmp;
 		}
+		if (tmp < 0)
+			return tmp;
+
 		*ppos += nr_bytes;
 		count -= nr_bytes;
 		buf += nr_bytes;
@@ -369,6 +373,8 @@
 		/* leave now if filled buffer already */
 		if (buflen == 0)
 			return acc;
+
+		cond_resched();
 	}
 
 	list_for_each_entry(m, &vmcore_list, list) {
@@ -390,6 +396,8 @@
 			if (buflen == 0)
 				return acc;
 		}
+
+		cond_resched();
 	}
 
 	return acc;
@@ -440,10 +448,6 @@
 #endif
 }
 
-static const struct vm_operations_struct vmcore_mmap_ops = {
-	.fault = mmap_vmcore_fault,
-};
-
 /**
  * vmcore_alloc_buf - allocate buffer in vmalloc memory
  * @sizez: size of buffer
@@ -471,6 +475,11 @@
  * virtually contiguous user-space in ELF layout.
  */
 #ifdef CONFIG_MMU
+
+static const struct vm_operations_struct vmcore_mmap_ops = {
+	.fault = mmap_vmcore_fault,
+};
+
 /*
  * remap_oldmem_pfn_checked - do remap_oldmem_pfn_range replacing all pages
  * reported as not being ram with the zero page.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/proc_namespace.c
+++ linux-xilinx-zynqmp-5.15.0/fs/proc_namespace.c
@@ -80,7 +80,7 @@
 			seq_puts(m, fs_infop->str);
 	}
 
-	if (mnt_user_ns(mnt) != &init_user_ns)
+	if (is_idmapped_mnt(mnt))
 		seq_puts(m, ",idmapped");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pstore/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/fs/pstore/Kconfig
@@ -126,6 +126,7 @@
 config PSTORE_PMSG
 	bool "Log user space messages"
 	depends on PSTORE
+	select RT_MUTEXES
 	help
 	  When the option is enabled, pstore will export a character
 	  interface /dev/pmsg0 to log user space messages. On reboot
@@ -173,7 +174,6 @@
 	tristate "Log panic/oops to a block device"
 	depends on PSTORE
 	depends on BLOCK
-	depends on BROKEN
 	select PSTORE_ZONE
 	default n
 	help
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pstore/blk.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pstore/blk.c
@@ -89,7 +89,7 @@
 		_##name_ = check_size(name, alignsize);		\
 	else							\
 		_##name_ = 0;					\
-	/* Synchronize module parameters with resuls. */	\
+	/* Synchronize module parameters with results. */	\
 	name = _##name_ / 1024;					\
 	dev->zone.name = _##name_;				\
 }
@@ -121,7 +121,7 @@
 	if (pstore_device_info)
 		return -EBUSY;
 
-	/* zero means not limit on which backends to attempt to store. */
+	/* zero means no limit on which backends attempt to store. */
 	if (!dev->flags)
 		dev->flags = UINT_MAX;
 
@@ -311,7 +311,7 @@
 	if (ret)
 		kfree(best_effort_dev);
 	else
-		pr_info("attached %s (%zu) (no dedicated panic_write!)\n",
+		pr_info("attached %s (%lu) (no dedicated panic_write!)\n",
 			blkdev, best_effort_dev->zone.total_size);
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pstore/platform.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pstore/platform.c
@@ -143,21 +143,22 @@
 	mod_timer(&pstore_timer, jiffies + msecs_to_jiffies(pstore_update_ms));
 }
 
-/*
- * Should pstore_dump() wait for a concurrent pstore_dump()? If
- * not, the current pstore_dump() will report a failure to dump
- * and return.
- */
-static bool pstore_cannot_wait(enum kmsg_dump_reason reason)
+static bool pstore_cannot_block_path(enum kmsg_dump_reason reason)
 {
-	/* In NMI path, pstore shouldn't block regardless of reason. */
+	/*
+	 * In case of NMI path, pstore shouldn't be blocked
+	 * regardless of reason.
+	 */
 	if (in_nmi())
 		return true;
 
 	switch (reason) {
 	/* In panic case, other cpus are stopped by smp_send_stop(). */
 	case KMSG_DUMP_PANIC:
-	/* Emergency restart shouldn't be blocked. */
+	/*
+	 * Emergency restart shouldn't be blocked by spinning on
+	 * pstore_info::buf_lock.
+	 */
 	case KMSG_DUMP_EMERG:
 		return true;
 	default:
@@ -389,21 +390,19 @@
 	unsigned long	total = 0;
 	const char	*why;
 	unsigned int	part = 1;
+	unsigned long	flags = 0;
 	int		ret;
 
 	why = kmsg_dump_reason_str(reason);
 
-	if (down_trylock(&psinfo->buf_lock)) {
-		/* Failed to acquire lock: give up if we cannot wait. */
-		if (pstore_cannot_wait(reason)) {
-			pr_err("dump skipped in %s path: may corrupt error record\n",
-				in_nmi() ? "NMI" : why);
-			return;
-		}
-		if (down_interruptible(&psinfo->buf_lock)) {
-			pr_err("could not grab semaphore?!\n");
+	if (pstore_cannot_block_path(reason)) {
+		if (!spin_trylock_irqsave(&psinfo->buf_lock, flags)) {
+			pr_err("dump skipped in %s path because of concurrent dump\n",
+					in_nmi() ? "NMI" : why);
 			return;
 		}
+	} else {
+		spin_lock_irqsave(&psinfo->buf_lock, flags);
 	}
 
 	kmsg_dump_rewind(&iter);
@@ -467,8 +466,7 @@
 		total += record.size;
 		part++;
 	}
-
-	up(&psinfo->buf_lock);
+	spin_unlock_irqrestore(&psinfo->buf_lock, flags);
 }
 
 static struct kmsg_dumper pstore_dumper = {
@@ -563,6 +561,8 @@
  */
 int pstore_register(struct pstore_info *psi)
 {
+	char *new_backend;
+
 	if (backend && strcmp(backend, psi->name)) {
 		pr_warn("ignoring unexpected backend '%s'\n", psi->name);
 		return -EPERM;
@@ -582,11 +582,16 @@
 		return -EINVAL;
 	}
 
+	new_backend = kstrdup(psi->name, GFP_KERNEL);
+	if (!new_backend)
+		return -ENOMEM;
+
 	mutex_lock(&psinfo_lock);
 	if (psinfo) {
 		pr_warn("backend '%s' already loaded: ignoring '%s'\n",
 			psinfo->name, psi->name);
 		mutex_unlock(&psinfo_lock);
+		kfree(new_backend);
 		return -EBUSY;
 	}
 
@@ -594,7 +599,7 @@
 		psi->write_user = pstore_write_user_compat;
 	psinfo = psi;
 	mutex_init(&psinfo->read_mutex);
-	sema_init(&psinfo->buf_lock, 1);
+	spin_lock_init(&psinfo->buf_lock);
 
 	if (psi->flags & PSTORE_FLAGS_DMESG)
 		allocate_buf_for_compression();
@@ -619,7 +624,7 @@
 	 * Update the module parameter backend, so it is visible
 	 * through /sys/module/pstore/parameters/backend
 	 */
-	backend = kstrdup(psi->name, GFP_KERNEL);
+	backend = new_backend;
 
 	pr_info("Registered %s as persistent store backend\n", psi->name);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pstore/ram.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pstore/ram.c
@@ -519,6 +519,7 @@
 	}
 
 	zone_sz = mem_sz / *cnt;
+	zone_sz = ALIGN_DOWN(zone_sz, 2);
 	if (!zone_sz) {
 		dev_err(dev, "%s zone size == 0\n", name);
 		goto fail;
@@ -670,7 +671,7 @@
 		field = value;						\
 	}
 
-	parse_u32("mem-type", pdata->record_size, pdata->mem_type);
+	parse_u32("mem-type", pdata->mem_type, pdata->mem_type);
 	parse_u32("record-size", pdata->record_size, 0);
 	parse_u32("console-size", pdata->console_size, 0);
 	parse_u32("ftrace-size", pdata->ftrace_size, 0);
@@ -735,6 +736,7 @@
 	/* Make sure we didn't get bogus platform data pointer. */
 	if (!pdata) {
 		pr_err("NULL platform data\n");
+		err = -EINVAL;
 		goto fail_out;
 	}
 
@@ -742,6 +744,7 @@
 			!pdata->ftrace_size && !pdata->pmsg_size)) {
 		pr_err("The memory size and the record/console size must be "
 			"non-zero\n");
+		err = -EINVAL;
 		goto fail_out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pstore/ram_core.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pstore/ram_core.c
@@ -190,7 +190,7 @@
 {
 	int numerr;
 	struct persistent_ram_buffer *buffer = prz->buffer;
-	int ecc_blocks;
+	size_t ecc_blocks;
 	size_t ecc_total;
 
 	if (!ecc_info || !ecc_info->ecc_size)
@@ -439,7 +439,11 @@
 		phys_addr_t addr = page_start + i * PAGE_SIZE;
 		pages[i] = pfn_to_page(addr >> PAGE_SHIFT);
 	}
-	vaddr = vmap(pages, page_count, VM_MAP, prot);
+	/*
+	 * VM_IOREMAP used here to bypass this region during vread()
+	 * and kmap_atomic() (i.e. kcore) to avoid __va() failures.
+	 */
+	vaddr = vmap(pages, page_count, VM_MAP | VM_IOREMAP, prot);
 	kfree(pages);
 
 	/*
@@ -514,7 +518,7 @@
 	sig ^= PERSISTENT_RAM_SIG;
 
 	if (prz->buffer->sig == sig) {
-		if (buffer_size(prz) == 0) {
+		if (buffer_size(prz) == 0 && buffer_start(prz) == 0) {
 			pr_debug("found existing empty buffer\n");
 			return 0;
 		}
@@ -587,6 +591,8 @@
 	raw_spin_lock_init(&prz->buffer_lock);
 	prz->flags = flags;
 	prz->label = kstrdup(label, GFP_KERNEL);
+	if (!prz->label)
+		goto err;
 
 	ret = persistent_ram_buffer_map(start, size, prz, memtype);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/pstore/zone.c
+++ linux-xilinx-zynqmp-5.15.0/fs/pstore/zone.c
@@ -761,7 +761,7 @@
 		/* avoid destroying old data, allocate a new one */
 		len = zone->buffer_size + sizeof(*zone->buffer);
 		zone->oldbuf = zone->buffer;
-		zone->buffer = kzalloc(len, GFP_KERNEL);
+		zone->buffer = kzalloc(len, GFP_ATOMIC);
 		if (!zone->buffer) {
 			zone->buffer = zone->oldbuf;
 			return -ENOMEM;
@@ -973,6 +973,8 @@
 		char *buf = kasprintf(GFP_KERNEL, "%s: Total %d times\n",
 				      kmsg_dump_reason_str(record->reason),
 				      record->count);
+		if (!buf)
+			return -ENOMEM;
 		hlen = strlen(buf);
 		record->buf = krealloc(buf, hlen + size, GFP_KERNEL);
 		if (!record->buf) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/quota/dquot.c
+++ linux-xilinx-zynqmp-5.15.0/fs/quota/dquot.c
@@ -79,6 +79,7 @@
 #include <linux/capability.h>
 #include <linux/quotaops.h>
 #include <linux/blkdev.h>
+#include <linux/sched/mm.h>
 #include "../internal.h" /* ugh */
 
 #include <linux/uaccess.h>
@@ -224,18 +225,26 @@
 
 /*
  * Dquot List Management:
- * The quota code uses four lists for dquot management: the inuse_list,
- * free_dquots, dqi_dirty_list, and dquot_hash[] array. A single dquot
- * structure may be on some of those lists, depending on its current state.
+ * The quota code uses five lists for dquot management: the inuse_list,
+ * releasing_dquots, free_dquots, dqi_dirty_list, and dquot_hash[] array.
+ * A single dquot structure may be on some of those lists, depending on
+ * its current state.
  *
  * All dquots are placed to the end of inuse_list when first created, and this
  * list is used for invalidate operation, which must look at every dquot.
  *
- * Unused dquots (dq_count == 0) are added to the free_dquots list when freed,
- * and this list is searched whenever we need an available dquot.  Dquots are
- * removed from the list as soon as they are used again, and
- * dqstats.free_dquots gives the number of dquots on the list. When
- * dquot is invalidated it's completely released from memory.
+ * When the last reference of a dquot is dropped, the dquot is added to
+ * releasing_dquots. We'll then queue work item which will call
+ * synchronize_srcu() and after that perform the final cleanup of all the
+ * dquots on the list. Each cleaned up dquot is moved to free_dquots list.
+ * Both releasing_dquots and free_dquots use the dq_free list_head in the dquot
+ * struct.
+ *
+ * Unused and cleaned up dquots are in the free_dquots list and this list is
+ * searched whenever we need an available dquot. Dquots are removed from the
+ * list as soon as they are used again and dqstats.free_dquots gives the number
+ * of dquots on the list. When dquot is invalidated it's completely released
+ * from memory.
  *
  * Dirty dquots are added to the dqi_dirty_list of quota_info when mark
  * dirtied, and this list is searched when writing dirty dquots back to
@@ -249,6 +258,7 @@
 
 static LIST_HEAD(inuse_list);
 static LIST_HEAD(free_dquots);
+static LIST_HEAD(releasing_dquots);
 static unsigned int dq_hash_bits, dq_hash_mask;
 static struct hlist_head *dquot_hash;
 
@@ -259,6 +269,9 @@
 static qsize_t __inode_get_rsv_space(struct inode *inode);
 static int __dquot_initialize(struct inode *inode, int type);
 
+static void quota_release_workfn(struct work_struct *work);
+static DECLARE_DELAYED_WORK(quota_release_work, quota_release_workfn);
+
 static inline unsigned int
 hashfn(const struct super_block *sb, struct kqid qid)
 {
@@ -304,12 +317,21 @@
 	dqstats_inc(DQST_FREE_DQUOTS);
 }
 
+static inline void put_releasing_dquots(struct dquot *dquot)
+{
+	list_add_tail(&dquot->dq_free, &releasing_dquots);
+	set_bit(DQ_RELEASING_B, &dquot->dq_flags);
+}
+
 static inline void remove_free_dquot(struct dquot *dquot)
 {
 	if (list_empty(&dquot->dq_free))
 		return;
 	list_del_init(&dquot->dq_free);
-	dqstats_dec(DQST_FREE_DQUOTS);
+	if (!test_bit(DQ_RELEASING_B, &dquot->dq_flags))
+		dqstats_dec(DQST_FREE_DQUOTS);
+	else
+		clear_bit(DQ_RELEASING_B, &dquot->dq_flags);
 }
 
 static inline void put_inuse(struct dquot *dquot)
@@ -335,6 +357,11 @@
 	mutex_unlock(&dquot->dq_lock);
 }
 
+static inline int dquot_active(struct dquot *dquot)
+{
+	return test_bit(DQ_ACTIVE_B, &dquot->dq_flags);
+}
+
 static inline int dquot_dirty(struct dquot *dquot)
 {
 	return test_bit(DQ_MOD_B, &dquot->dq_flags);
@@ -350,14 +377,14 @@
 {
 	int ret = 1;
 
-	if (!test_bit(DQ_ACTIVE_B, &dquot->dq_flags))
+	if (!dquot_active(dquot))
 		return 0;
 
 	if (sb_dqopt(dquot->dq_sb)->flags & DQUOT_NOLIST_DIRTY)
 		return test_and_set_bit(DQ_MOD_B, &dquot->dq_flags);
 
 	/* If quota is dirty already, we don't have to acquire dq_list_lock */
-	if (test_bit(DQ_MOD_B, &dquot->dq_flags))
+	if (dquot_dirty(dquot))
 		return 1;
 
 	spin_lock(&dq_list_lock);
@@ -372,15 +399,17 @@
 EXPORT_SYMBOL(dquot_mark_dquot_dirty);
 
 /* Dirtify all the dquots - this can block when journalling */
-static inline int mark_all_dquot_dirty(struct dquot * const *dquot)
+static inline int mark_all_dquot_dirty(struct dquot __rcu * const *dquots)
 {
 	int ret, err, cnt;
+	struct dquot *dquot;
 
 	ret = err = 0;
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
-		if (dquot[cnt])
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (dquot)
 			/* Even in case of error we have to continue */
-			ret = mark_dquot_dirty(dquot[cnt]);
+			ret = mark_dquot_dirty(dquot);
 		if (!err)
 			err = ret;
 	}
@@ -425,9 +454,11 @@
 int dquot_acquire(struct dquot *dquot)
 {
 	int ret = 0, ret2 = 0;
+	unsigned int memalloc;
 	struct quota_info *dqopt = sb_dqopt(dquot->dq_sb);
 
 	mutex_lock(&dquot->dq_lock);
+	memalloc = memalloc_nofs_save();
 	if (!test_bit(DQ_READ_B, &dquot->dq_flags)) {
 		ret = dqopt->ops[dquot->dq_id.type]->read_dqblk(dquot);
 		if (ret < 0)
@@ -437,7 +468,7 @@
 	smp_mb__before_atomic();
 	set_bit(DQ_READ_B, &dquot->dq_flags);
 	/* Instantiate dquot if needed */
-	if (!test_bit(DQ_ACTIVE_B, &dquot->dq_flags) && !dquot->dq_off) {
+	if (!dquot_active(dquot) && !dquot->dq_off) {
 		ret = dqopt->ops[dquot->dq_id.type]->commit_dqblk(dquot);
 		/* Write the info if needed */
 		if (info_dirty(&dqopt->info[dquot->dq_id.type])) {
@@ -458,6 +489,7 @@
 	smp_mb__before_atomic();
 	set_bit(DQ_ACTIVE_B, &dquot->dq_flags);
 out_iolock:
+	memalloc_nofs_restore(memalloc);
 	mutex_unlock(&dquot->dq_lock);
 	return ret;
 }
@@ -469,18 +501,21 @@
 int dquot_commit(struct dquot *dquot)
 {
 	int ret = 0;
+	unsigned int memalloc;
 	struct quota_info *dqopt = sb_dqopt(dquot->dq_sb);
 
 	mutex_lock(&dquot->dq_lock);
+	memalloc = memalloc_nofs_save();
 	if (!clear_dquot_dirty(dquot))
 		goto out_lock;
 	/* Inactive dquot can be only if there was error during read/init
 	 * => we have better not writing it */
-	if (test_bit(DQ_ACTIVE_B, &dquot->dq_flags))
+	if (dquot_active(dquot))
 		ret = dqopt->ops[dquot->dq_id.type]->commit_dqblk(dquot);
 	else
 		ret = -EIO;
 out_lock:
+	memalloc_nofs_restore(memalloc);
 	mutex_unlock(&dquot->dq_lock);
 	return ret;
 }
@@ -492,9 +527,11 @@
 int dquot_release(struct dquot *dquot)
 {
 	int ret = 0, ret2 = 0;
+	unsigned int memalloc;
 	struct quota_info *dqopt = sb_dqopt(dquot->dq_sb);
 
 	mutex_lock(&dquot->dq_lock);
+	memalloc = memalloc_nofs_save();
 	/* Check whether we are not racing with some other dqget() */
 	if (dquot_is_busy(dquot))
 		goto out_dqlock;
@@ -510,6 +547,7 @@
 	}
 	clear_bit(DQ_ACTIVE_B, &dquot->dq_flags);
 out_dqlock:
+	memalloc_nofs_restore(memalloc);
 	mutex_unlock(&dquot->dq_lock);
 	return ret;
 }
@@ -537,6 +575,8 @@
 	struct dquot *dquot, *tmp;
 
 restart:
+	flush_delayed_work(&quota_release_work);
+
 	spin_lock(&dq_list_lock);
 	list_for_each_entry_safe(dquot, tmp, &inuse_list, dq_inuse) {
 		if (dquot->dq_sb != sb)
@@ -545,7 +585,7 @@
 			continue;
 		/* Wait for dquot users */
 		if (atomic_read(&dquot->dq_count)) {
-			dqgrab(dquot);
+			atomic_inc(&dquot->dq_count);
 			spin_unlock(&dq_list_lock);
 			/*
 			 * Once dqput() wakes us up, we know it's time to free
@@ -564,6 +604,15 @@
 			goto restart;
 		}
 		/*
+		 * The last user already dropped its reference but dquot didn't
+		 * get fully cleaned up yet. Restart the scan which flushes the
+		 * work cleaning up released dquots.
+		 */
+		if (test_bit(DQ_RELEASING_B, &dquot->dq_flags)) {
+			spin_unlock(&dq_list_lock);
+			goto restart;
+		}
+		/*
 		 * Quota now has no users and it has been written on last
 		 * dqput()
 		 */
@@ -587,7 +636,7 @@
 
 	spin_lock(&dq_list_lock);
 	list_for_each_entry(dquot, &inuse_list, dq_inuse) {
-		if (!test_bit(DQ_ACTIVE_B, &dquot->dq_flags))
+		if (!dquot_active(dquot))
 			continue;
 		if (dquot->dq_sb != sb)
 			continue;
@@ -602,7 +651,7 @@
 		 * outstanding call and recheck the DQ_ACTIVE_B after that.
 		 */
 		wait_on_dquot(dquot);
-		if (test_bit(DQ_ACTIVE_B, &dquot->dq_flags)) {
+		if (dquot_active(dquot)) {
 			ret = fn(dquot, priv);
 			if (ret < 0)
 				goto out;
@@ -618,6 +667,18 @@
 }
 EXPORT_SYMBOL(dquot_scan_active);
 
+static inline int dquot_write_dquot(struct dquot *dquot)
+{
+	int ret = dquot->dq_sb->dq_op->write_dquot(dquot);
+	if (ret < 0) {
+		quota_error(dquot->dq_sb, "Can't write quota structure "
+			    "(error %d). Quota may get out of sync!", ret);
+		/* Clear dirty bit anyway to avoid infinite loop. */
+		clear_dquot_dirty(dquot);
+	}
+	return ret;
+}
+
 /* Write all dquot structures to quota files */
 int dquot_writeback_dquots(struct super_block *sb, int type)
 {
@@ -629,6 +690,8 @@
 
 	WARN_ON_ONCE(!rwsem_is_locked(&sb->s_umount));
 
+	flush_delayed_work(&quota_release_work);
+
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
 		if (type != -1 && cnt != type)
 			continue;
@@ -641,23 +704,23 @@
 			dquot = list_first_entry(&dirty, struct dquot,
 						 dq_dirty);
 
-			WARN_ON(!test_bit(DQ_ACTIVE_B, &dquot->dq_flags));
+			WARN_ON(!dquot_active(dquot));
+			/* If the dquot is releasing we should not touch it */
+			if (test_bit(DQ_RELEASING_B, &dquot->dq_flags)) {
+				spin_unlock(&dq_list_lock);
+				flush_delayed_work(&quota_release_work);
+				spin_lock(&dq_list_lock);
+				continue;
+			}
 
 			/* Now we have active dquot from which someone is
  			 * holding reference so we can safely just increase
 			 * use count */
 			dqgrab(dquot);
 			spin_unlock(&dq_list_lock);
-			err = sb->dq_op->write_dquot(dquot);
-			if (err) {
-				/*
-				 * Clear dirty bit anyway to avoid infinite
-				 * loop here.
-				 */
-				clear_dquot_dirty(dquot);
-				if (!ret)
-					ret = err;
-			}
+			err = dquot_write_dquot(dquot);
+			if (err && !ret)
+				ret = err;
 			dqput(dquot);
 			spin_lock(&dq_list_lock);
 		}
@@ -690,9 +753,14 @@
 	/* This is not very clever (and fast) but currently I don't know about
 	 * any other simple way of getting quota data to disk and we must get
 	 * them there for userspace to be visible... */
-	if (sb->s_op->sync_fs)
-		sb->s_op->sync_fs(sb, 1);
-	sync_blockdev(sb->s_bdev);
+	if (sb->s_op->sync_fs) {
+		ret = sb->s_op->sync_fs(sb, 1);
+		if (ret)
+			return ret;
+	}
+	ret = sync_blockdev(sb->s_bdev);
+	if (ret)
+		return ret;
 
 	/*
 	 * Now when everything is written we can discard the pagecache so
@@ -746,12 +814,52 @@
 };
 
 /*
+ * Safely release dquot and put reference to dquot.
+ */
+static void quota_release_workfn(struct work_struct *work)
+{
+	struct dquot *dquot;
+	struct list_head rls_head;
+
+	spin_lock(&dq_list_lock);
+	/* Exchange the list head to avoid livelock. */
+	list_replace_init(&releasing_dquots, &rls_head);
+	spin_unlock(&dq_list_lock);
+	synchronize_srcu(&dquot_srcu);
+
+restart:
+	spin_lock(&dq_list_lock);
+	while (!list_empty(&rls_head)) {
+		dquot = list_first_entry(&rls_head, struct dquot, dq_free);
+		WARN_ON_ONCE(atomic_read(&dquot->dq_count));
+		/*
+		 * Note that DQ_RELEASING_B protects us from racing with
+		 * invalidate_dquots() calls so we are safe to work with the
+		 * dquot even after we drop dq_list_lock.
+		 */
+		if (dquot_dirty(dquot)) {
+			spin_unlock(&dq_list_lock);
+			/* Commit dquot before releasing */
+			dquot_write_dquot(dquot);
+			goto restart;
+		}
+		if (dquot_active(dquot)) {
+			spin_unlock(&dq_list_lock);
+			dquot->dq_sb->dq_op->release_dquot(dquot);
+			goto restart;
+		}
+		/* Dquot is inactive and clean, now move it to free list */
+		remove_free_dquot(dquot);
+		put_dquot_last(dquot);
+	}
+	spin_unlock(&dq_list_lock);
+}
+
+/*
  * Put reference to dquot
  */
 void dqput(struct dquot *dquot)
 {
-	int ret;
-
 	if (!dquot)
 		return;
 #ifdef CONFIG_QUOTA_DEBUG
@@ -763,7 +871,7 @@
 	}
 #endif
 	dqstats_inc(DQST_DROPS);
-we_slept:
+
 	spin_lock(&dq_list_lock);
 	if (atomic_read(&dquot->dq_count) > 1) {
 		/* We have more than one user... nothing to do */
@@ -775,35 +883,16 @@
 		spin_unlock(&dq_list_lock);
 		return;
 	}
+
 	/* Need to release dquot? */
-	if (dquot_dirty(dquot)) {
-		spin_unlock(&dq_list_lock);
-		/* Commit dquot before releasing */
-		ret = dquot->dq_sb->dq_op->write_dquot(dquot);
-		if (ret < 0) {
-			quota_error(dquot->dq_sb, "Can't write quota structure"
-				    " (error %d). Quota may get out of sync!",
-				    ret);
-			/*
-			 * We clear dirty bit anyway, so that we avoid
-			 * infinite loop here
-			 */
-			clear_dquot_dirty(dquot);
-		}
-		goto we_slept;
-	}
-	if (test_bit(DQ_ACTIVE_B, &dquot->dq_flags)) {
-		spin_unlock(&dq_list_lock);
-		dquot->dq_sb->dq_op->release_dquot(dquot);
-		goto we_slept;
-	}
-	atomic_dec(&dquot->dq_count);
 #ifdef CONFIG_QUOTA_DEBUG
 	/* sanity check */
 	BUG_ON(!list_empty(&dquot->dq_free));
 #endif
-	put_dquot_last(dquot);
+	put_releasing_dquots(dquot);
+	atomic_dec(&dquot->dq_count);
 	spin_unlock(&dq_list_lock);
+	queue_delayed_work(system_unbound_wq, &quota_release_work, 1);
 }
 EXPORT_SYMBOL(dqput);
 
@@ -890,10 +979,10 @@
 		dqstats_inc(DQST_LOOKUPS);
 	}
 	/* Wait for dq_lock - after this we know that either dquot_release() is
-	 * already finished or it will be canceled due to dq_count > 1 test */
+	 * already finished or it will be canceled due to dq_count > 0 test */
 	wait_on_dquot(dquot);
 	/* Read the dquot / allocate space in quota file */
-	if (!test_bit(DQ_ACTIVE_B, &dquot->dq_flags)) {
+	if (!dquot_active(dquot)) {
 		int err;
 
 		err = sb->dq_op->acquire_dquot(dquot);
@@ -908,9 +997,8 @@
 	 * smp_mb__before_atomic() in dquot_acquire().
 	 */
 	smp_rmb();
-#ifdef CONFIG_QUOTA_DEBUG
-	BUG_ON(!dquot->dq_sb);	/* Has somebody invalidated entry under us? */
-#endif
+	/* Has somebody invalidated entry under us? */
+	WARN_ON_ONCE(hlist_unhashed(&dquot->dq_hash));
 out:
 	if (empty)
 		do_destroy_dquot(empty);
@@ -919,14 +1007,15 @@
 }
 EXPORT_SYMBOL(dqget);
 
-static inline struct dquot **i_dquot(struct inode *inode)
+static inline struct dquot __rcu **i_dquot(struct inode *inode)
 {
-	return inode->i_sb->s_op->get_dquots(inode);
+	/* Force __rcu for now until filesystems are fixed */
+	return (struct dquot __rcu **)inode->i_sb->s_op->get_dquots(inode);
 }
 
 static int dqinit_needed(struct inode *inode, int type)
 {
-	struct dquot * const *dquots;
+	struct dquot __rcu * const *dquots;
 	int cnt;
 
 	if (IS_NOQUOTA(inode))
@@ -999,59 +1088,7 @@
 	return err;
 }
 
-/*
- * Remove references to dquots from inode and add dquot to list for freeing
- * if we have the last reference to dquot
- */
-static void remove_inode_dquot_ref(struct inode *inode, int type,
-				   struct list_head *tofree_head)
-{
-	struct dquot **dquots = i_dquot(inode);
-	struct dquot *dquot = dquots[type];
-
-	if (!dquot)
-		return;
-
-	dquots[type] = NULL;
-	if (list_empty(&dquot->dq_free)) {
-		/*
-		 * The inode still has reference to dquot so it can't be in the
-		 * free list
-		 */
-		spin_lock(&dq_list_lock);
-		list_add(&dquot->dq_free, tofree_head);
-		spin_unlock(&dq_list_lock);
-	} else {
-		/*
-		 * Dquot is already in a list to put so we won't drop the last
-		 * reference here.
-		 */
-		dqput(dquot);
-	}
-}
-
-/*
- * Free list of dquots
- * Dquots are removed from inodes and no new references can be got so we are
- * the only ones holding reference
- */
-static void put_dquot_list(struct list_head *tofree_head)
-{
-	struct list_head *act_head;
-	struct dquot *dquot;
-
-	act_head = tofree_head->next;
-	while (act_head != tofree_head) {
-		dquot = list_entry(act_head, struct dquot, dq_free);
-		act_head = act_head->next;
-		/* Remove dquot from the list so we won't have problems... */
-		list_del_init(&dquot->dq_free);
-		dqput(dquot);
-	}
-}
-
-static void remove_dquot_ref(struct super_block *sb, int type,
-		struct list_head *tofree_head)
+static void remove_dquot_ref(struct super_block *sb, int type)
 {
 	struct inode *inode;
 #ifdef CONFIG_QUOTA_DEBUG
@@ -1068,11 +1105,18 @@
 		 */
 		spin_lock(&dq_data_lock);
 		if (!IS_NOQUOTA(inode)) {
+			struct dquot __rcu **dquots = i_dquot(inode);
+			struct dquot *dquot = srcu_dereference_check(
+				dquots[type], &dquot_srcu,
+				lockdep_is_held(&dq_data_lock));
+
 #ifdef CONFIG_QUOTA_DEBUG
 			if (unlikely(inode_get_rsv_space(inode) > 0))
 				reserved = 1;
 #endif
-			remove_inode_dquot_ref(inode, type, tofree_head);
+			rcu_assign_pointer(dquots[type], NULL);
+			if (dquot)
+				dqput(dquot);
 		}
 		spin_unlock(&dq_data_lock);
 	}
@@ -1089,13 +1133,8 @@
 /* Gather all references from inodes and drop them */
 static void drop_dquot_ref(struct super_block *sb, int type)
 {
-	LIST_HEAD(tofree_head);
-
-	if (sb->dq_op) {
-		remove_dquot_ref(sb, type, &tofree_head);
-		synchronize_srcu(&dquot_srcu);
-		put_dquot_list(&tofree_head);
-	}
+	if (sb->dq_op)
+		remove_dquot_ref(sb, type);
 }
 
 static inline
@@ -1410,7 +1449,7 @@
 	return QUOTA_NL_NOWARN;
 }
 
-static int dquot_active(const struct inode *inode)
+static int inode_quota_active(const struct inode *inode)
 {
 	struct super_block *sb = inode->i_sb;
 
@@ -1428,12 +1467,13 @@
 static int __dquot_initialize(struct inode *inode, int type)
 {
 	int cnt, init_needed = 0;
-	struct dquot **dquots, *got[MAXQUOTAS] = {};
+	struct dquot __rcu **dquots;
+	struct dquot *got[MAXQUOTAS] = {};
 	struct super_block *sb = inode->i_sb;
 	qsize_t rsv;
 	int ret = 0;
 
-	if (!dquot_active(inode))
+	if (!inode_quota_active(inode))
 		return 0;
 
 	dquots = i_dquot(inode);
@@ -1503,7 +1543,7 @@
 		if (!got[cnt])
 			continue;
 		if (!dquots[cnt]) {
-			dquots[cnt] = got[cnt];
+			rcu_assign_pointer(dquots[cnt], got[cnt]);
 			got[cnt] = NULL;
 			/*
 			 * Make quota reservation system happy if someone
@@ -1511,12 +1551,16 @@
 			 */
 			rsv = inode_get_rsv_space(inode);
 			if (unlikely(rsv)) {
+				struct dquot *dquot = srcu_dereference_check(
+					dquots[cnt], &dquot_srcu,
+					lockdep_is_held(&dq_data_lock));
+
 				spin_lock(&inode->i_lock);
 				/* Get reservation again under proper lock */
 				rsv = __inode_get_rsv_space(inode);
-				spin_lock(&dquots[cnt]->dq_dqb_lock);
-				dquots[cnt]->dq_dqb.dqb_rsvspace += rsv;
-				spin_unlock(&dquots[cnt]->dq_dqb_lock);
+				spin_lock(&dquot->dq_dqb_lock);
+				dquot->dq_dqb.dqb_rsvspace += rsv;
+				spin_unlock(&dquot->dq_dqb_lock);
 				spin_unlock(&inode->i_lock);
 			}
 		}
@@ -1538,10 +1582,10 @@
 
 bool dquot_initialize_needed(struct inode *inode)
 {
-	struct dquot **dquots;
+	struct dquot __rcu **dquots;
 	int i;
 
-	if (!dquot_active(inode))
+	if (!inode_quota_active(inode))
 		return false;
 
 	dquots = i_dquot(inode);
@@ -1563,13 +1607,14 @@
 static void __dquot_drop(struct inode *inode)
 {
 	int cnt;
-	struct dquot **dquots = i_dquot(inode);
+	struct dquot __rcu **dquots = i_dquot(inode);
 	struct dquot *put[MAXQUOTAS];
 
 	spin_lock(&dq_data_lock);
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
-		put[cnt] = dquots[cnt];
-		dquots[cnt] = NULL;
+		put[cnt] = srcu_dereference_check(dquots[cnt], &dquot_srcu,
+					lockdep_is_held(&dq_data_lock));
+		rcu_assign_pointer(dquots[cnt], NULL);
 	}
 	spin_unlock(&dq_data_lock);
 	dqput_all(put);
@@ -1577,7 +1622,7 @@
 
 void dquot_drop(struct inode *inode)
 {
-	struct dquot * const *dquots;
+	struct dquot __rcu * const *dquots;
 	int cnt;
 
 	if (IS_NOQUOTA(inode))
@@ -1650,9 +1695,10 @@
 	int cnt, ret = 0, index;
 	struct dquot_warn warn[MAXQUOTAS];
 	int reserve = flags & DQUOT_SPACE_RESERVE;
-	struct dquot **dquots;
+	struct dquot __rcu **dquots;
+	struct dquot *dquot;
 
-	if (!dquot_active(inode)) {
+	if (!inode_quota_active(inode)) {
 		if (reserve) {
 			spin_lock(&inode->i_lock);
 			*inode_reserved_space(inode) += number;
@@ -1670,27 +1716,26 @@
 	index = srcu_read_lock(&dquot_srcu);
 	spin_lock(&inode->i_lock);
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
-		if (!dquots[cnt])
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (!dquot)
 			continue;
 		if (reserve) {
-			ret = dquot_add_space(dquots[cnt], 0, number, flags,
-					      &warn[cnt]);
+			ret = dquot_add_space(dquot, 0, number, flags, &warn[cnt]);
 		} else {
-			ret = dquot_add_space(dquots[cnt], number, 0, flags,
-					      &warn[cnt]);
+			ret = dquot_add_space(dquot, number, 0, flags, &warn[cnt]);
 		}
 		if (ret) {
 			/* Back out changes we already did */
 			for (cnt--; cnt >= 0; cnt--) {
-				if (!dquots[cnt])
+				dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+				if (!dquot)
 					continue;
-				spin_lock(&dquots[cnt]->dq_dqb_lock);
+				spin_lock(&dquot->dq_dqb_lock);
 				if (reserve)
-					dquot_free_reserved_space(dquots[cnt],
-								  number);
+					dquot_free_reserved_space(dquot, number);
 				else
-					dquot_decr_space(dquots[cnt], number);
-				spin_unlock(&dquots[cnt]->dq_dqb_lock);
+					dquot_decr_space(dquot, number);
+				spin_unlock(&dquot->dq_dqb_lock);
 			}
 			spin_unlock(&inode->i_lock);
 			goto out_flush_warn;
@@ -1720,9 +1765,10 @@
 {
 	int cnt, ret = 0, index;
 	struct dquot_warn warn[MAXQUOTAS];
-	struct dquot * const *dquots;
+	struct dquot __rcu * const *dquots;
+	struct dquot *dquot;
 
-	if (!dquot_active(inode))
+	if (!inode_quota_active(inode))
 		return 0;
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++)
 		warn[cnt].w_type = QUOTA_NL_NOWARN;
@@ -1731,17 +1777,19 @@
 	index = srcu_read_lock(&dquot_srcu);
 	spin_lock(&inode->i_lock);
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
-		if (!dquots[cnt])
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (!dquot)
 			continue;
-		ret = dquot_add_inodes(dquots[cnt], 1, &warn[cnt]);
+		ret = dquot_add_inodes(dquot, 1, &warn[cnt]);
 		if (ret) {
 			for (cnt--; cnt >= 0; cnt--) {
-				if (!dquots[cnt])
+				dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+				if (!dquot)
 					continue;
 				/* Back out changes we already did */
-				spin_lock(&dquots[cnt]->dq_dqb_lock);
-				dquot_decr_inodes(dquots[cnt], 1);
-				spin_unlock(&dquots[cnt]->dq_dqb_lock);
+				spin_lock(&dquot->dq_dqb_lock);
+				dquot_decr_inodes(dquot, 1);
+				spin_unlock(&dquot->dq_dqb_lock);
 			}
 			goto warn_put_all;
 		}
@@ -1762,10 +1810,11 @@
  */
 int dquot_claim_space_nodirty(struct inode *inode, qsize_t number)
 {
-	struct dquot **dquots;
+	struct dquot __rcu **dquots;
+	struct dquot *dquot;
 	int cnt, index;
 
-	if (!dquot_active(inode)) {
+	if (!inode_quota_active(inode)) {
 		spin_lock(&inode->i_lock);
 		*inode_reserved_space(inode) -= number;
 		__inode_add_bytes(inode, number);
@@ -1778,9 +1827,8 @@
 	spin_lock(&inode->i_lock);
 	/* Claim reserved quotas to allocated quotas */
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
-		if (dquots[cnt]) {
-			struct dquot *dquot = dquots[cnt];
-
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (dquot) {
 			spin_lock(&dquot->dq_dqb_lock);
 			if (WARN_ON_ONCE(dquot->dq_dqb.dqb_rsvspace < number))
 				number = dquot->dq_dqb.dqb_rsvspace;
@@ -1804,10 +1852,11 @@
  */
 void dquot_reclaim_space_nodirty(struct inode *inode, qsize_t number)
 {
-	struct dquot **dquots;
+	struct dquot __rcu **dquots;
+	struct dquot *dquot;
 	int cnt, index;
 
-	if (!dquot_active(inode)) {
+	if (!inode_quota_active(inode)) {
 		spin_lock(&inode->i_lock);
 		*inode_reserved_space(inode) += number;
 		__inode_sub_bytes(inode, number);
@@ -1820,9 +1869,8 @@
 	spin_lock(&inode->i_lock);
 	/* Claim reserved quotas to allocated quotas */
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
-		if (dquots[cnt]) {
-			struct dquot *dquot = dquots[cnt];
-
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (dquot) {
 			spin_lock(&dquot->dq_dqb_lock);
 			if (WARN_ON_ONCE(dquot->dq_dqb.dqb_curspace < number))
 				number = dquot->dq_dqb.dqb_curspace;
@@ -1848,10 +1896,11 @@
 {
 	unsigned int cnt;
 	struct dquot_warn warn[MAXQUOTAS];
-	struct dquot **dquots;
+	struct dquot __rcu **dquots;
+	struct dquot *dquot;
 	int reserve = flags & DQUOT_SPACE_RESERVE, index;
 
-	if (!dquot_active(inode)) {
+	if (!inode_quota_active(inode)) {
 		if (reserve) {
 			spin_lock(&inode->i_lock);
 			*inode_reserved_space(inode) -= number;
@@ -1869,17 +1918,18 @@
 		int wtype;
 
 		warn[cnt].w_type = QUOTA_NL_NOWARN;
-		if (!dquots[cnt])
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (!dquot)
 			continue;
-		spin_lock(&dquots[cnt]->dq_dqb_lock);
-		wtype = info_bdq_free(dquots[cnt], number);
+		spin_lock(&dquot->dq_dqb_lock);
+		wtype = info_bdq_free(dquot, number);
 		if (wtype != QUOTA_NL_NOWARN)
-			prepare_warning(&warn[cnt], dquots[cnt], wtype);
+			prepare_warning(&warn[cnt], dquot, wtype);
 		if (reserve)
-			dquot_free_reserved_space(dquots[cnt], number);
+			dquot_free_reserved_space(dquot, number);
 		else
-			dquot_decr_space(dquots[cnt], number);
-		spin_unlock(&dquots[cnt]->dq_dqb_lock);
+			dquot_decr_space(dquot, number);
+		spin_unlock(&dquot->dq_dqb_lock);
 	}
 	if (reserve)
 		*inode_reserved_space(inode) -= number;
@@ -1903,10 +1953,11 @@
 {
 	unsigned int cnt;
 	struct dquot_warn warn[MAXQUOTAS];
-	struct dquot * const *dquots;
+	struct dquot __rcu * const *dquots;
+	struct dquot *dquot;
 	int index;
 
-	if (!dquot_active(inode))
+	if (!inode_quota_active(inode))
 		return;
 
 	dquots = i_dquot(inode);
@@ -1914,16 +1965,16 @@
 	spin_lock(&inode->i_lock);
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
 		int wtype;
-
 		warn[cnt].w_type = QUOTA_NL_NOWARN;
-		if (!dquots[cnt])
+		dquot = srcu_dereference(dquots[cnt], &dquot_srcu);
+		if (!dquot)
 			continue;
-		spin_lock(&dquots[cnt]->dq_dqb_lock);
-		wtype = info_idq_free(dquots[cnt], 1);
+		spin_lock(&dquot->dq_dqb_lock);
+		wtype = info_idq_free(dquot, 1);
 		if (wtype != QUOTA_NL_NOWARN)
-			prepare_warning(&warn[cnt], dquots[cnt], wtype);
-		dquot_decr_inodes(dquots[cnt], 1);
-		spin_unlock(&dquots[cnt]->dq_dqb_lock);
+			prepare_warning(&warn[cnt], dquot, wtype);
+		dquot_decr_inodes(dquot, 1);
+		spin_unlock(&dquot->dq_dqb_lock);
 	}
 	spin_unlock(&inode->i_lock);
 	mark_all_dquot_dirty(dquots);
@@ -1949,8 +2000,9 @@
 	qsize_t cur_space;
 	qsize_t rsv_space = 0;
 	qsize_t inode_usage = 1;
+	struct dquot __rcu **dquots;
 	struct dquot *transfer_from[MAXQUOTAS] = {};
-	int cnt, ret = 0;
+	int cnt, index, ret = 0;
 	char is_valid[MAXQUOTAS] = {};
 	struct dquot_warn warn_to[MAXQUOTAS];
 	struct dquot_warn warn_from_inodes[MAXQUOTAS];
@@ -1981,6 +2033,7 @@
 	}
 	cur_space = __inode_get_bytes(inode);
 	rsv_space = __inode_get_rsv_space(inode);
+	dquots = i_dquot(inode);
 	/*
 	 * Build the transfer_from list, check limits, and update usage in
 	 * the target structures.
@@ -1995,7 +2048,8 @@
 		if (!sb_has_quota_active(inode->i_sb, cnt))
 			continue;
 		is_valid[cnt] = 1;
-		transfer_from[cnt] = i_dquot(inode)[cnt];
+		transfer_from[cnt] = srcu_dereference_check(dquots[cnt],
+				&dquot_srcu, lockdep_is_held(&dq_data_lock));
 		ret = dquot_add_inodes(transfer_to[cnt], inode_usage,
 				       &warn_to[cnt]);
 		if (ret)
@@ -2034,13 +2088,21 @@
 						  rsv_space);
 			spin_unlock(&transfer_from[cnt]->dq_dqb_lock);
 		}
-		i_dquot(inode)[cnt] = transfer_to[cnt];
+		rcu_assign_pointer(dquots[cnt], transfer_to[cnt]);
 	}
 	spin_unlock(&inode->i_lock);
 	spin_unlock(&dq_data_lock);
 
-	mark_all_dquot_dirty(transfer_from);
-	mark_all_dquot_dirty(transfer_to);
+	/*
+	 * These arrays are local and we hold dquot references so we don't need
+	 * the srcu protection but still take dquot_srcu to avoid warning in
+	 * mark_all_dquot_dirty().
+	 */
+	index = srcu_read_lock(&dquot_srcu);
+	mark_all_dquot_dirty((struct dquot __rcu **)transfer_from);
+	mark_all_dquot_dirty((struct dquot __rcu **)transfer_to);
+	srcu_read_unlock(&dquot_srcu, index);
+
 	flush_warnings(warn_to);
 	flush_warnings(warn_from_inodes);
 	flush_warnings(warn_from_space);
@@ -2077,7 +2139,7 @@
 	struct super_block *sb = inode->i_sb;
 	int ret;
 
-	if (!dquot_active(inode))
+	if (!inode_quota_active(inode))
 		return 0;
 
 	if (iattr->ia_valid & ATTR_UID && !uid_eq(iattr->ia_uid, inode->i_uid)){
@@ -2302,6 +2364,8 @@
 	struct super_block *sb = inode->i_sb;
 	struct quota_info *dqopt = sb_dqopt(sb);
 
+	if (is_bad_inode(inode))
+		return -EUCLEAN;
 	if (!S_ISREG(inode->i_mode))
 		return -EACCES;
 	if (IS_RDONLY(inode))
@@ -2309,6 +2373,20 @@
 	if (sb_has_quota_loaded(sb, type))
 		return -EBUSY;
 
+	/*
+	 * Quota files should never be encrypted.  They should be thought of as
+	 * filesystem metadata, not user data.  New-style internal quota files
+	 * cannot be encrypted by users anyway, but old-style external quota
+	 * files could potentially be incorrectly created in an encrypted
+	 * directory, hence this explicit check.  Some reasons why encrypted
+	 * quota files don't work include: (1) some filesystems that support
+	 * encryption don't handle it in their quota_read and quota_write, and
+	 * (2) cleaning up encrypted quota files at unmount would need special
+	 * consideration, as quota files are cleaned up later than user files.
+	 */
+	if (IS_ENCRYPTED(inode))
+		return -EINVAL;
+
 	dqopt->files[type] = igrab(inode);
 	if (!dqopt->files[type])
 		return -EIO;
@@ -2396,7 +2474,8 @@
 
 	error = add_dquot_ref(sb, type);
 	if (error)
-		dquot_disable(sb, type, flags);
+		dquot_disable(sb, type,
+			      DQUOT_USAGE_ENABLED | DQUOT_LIMITS_ENABLED);
 
 	return error;
 out_fmt:
--- linux-xilinx-zynqmp-5.15.0.orig/fs/quota/quota_tree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/quota/quota_tree.c
@@ -71,6 +71,35 @@
 	return ret;
 }
 
+static inline int do_check_range(struct super_block *sb, const char *val_name,
+				 uint val, uint min_val, uint max_val)
+{
+	if (val < min_val || val > max_val) {
+		quota_error(sb, "Getting %s %u out of range %u-%u",
+			    val_name, val, min_val, max_val);
+		return -EUCLEAN;
+	}
+
+	return 0;
+}
+
+static int check_dquot_block_header(struct qtree_mem_dqinfo *info,
+				    struct qt_disk_dqdbheader *dh)
+{
+	int err = 0;
+
+	err = do_check_range(info->dqi_sb, "dqdh_next_free",
+			     le32_to_cpu(dh->dqdh_next_free), 0,
+			     info->dqi_blocks - 1);
+	if (err)
+		return err;
+	err = do_check_range(info->dqi_sb, "dqdh_prev_free",
+			     le32_to_cpu(dh->dqdh_prev_free), 0,
+			     info->dqi_blocks - 1);
+
+	return err;
+}
+
 /* Remove empty block from list and return it */
 static int get_free_dqblk(struct qtree_mem_dqinfo *info)
 {
@@ -85,6 +114,9 @@
 		ret = read_blk(info, blk, buf);
 		if (ret < 0)
 			goto out_buf;
+		ret = check_dquot_block_header(info, dh);
+		if (ret)
+			goto out_buf;
 		info->dqi_free_blk = le32_to_cpu(dh->dqdh_next_free);
 	}
 	else {
@@ -232,6 +264,9 @@
 		*err = read_blk(info, blk, buf);
 		if (*err < 0)
 			goto out_buf;
+		*err = check_dquot_block_header(info, dh);
+		if (*err)
+			goto out_buf;
 	} else {
 		blk = get_free_dqblk(info);
 		if ((int)blk < 0) {
@@ -414,6 +449,7 @@
 		quota_error(dquot->dq_sb, "Quota structure has offset to "
 			"other block (%u) than it should (%u)", blk,
 			(uint)(dquot->dq_off >> info->dqi_blocksize_bits));
+		ret = -EIO;
 		goto out_buf;
 	}
 	ret = read_blk(info, blk, buf);
@@ -423,6 +459,9 @@
 		goto out_buf;
 	}
 	dh = (struct qt_disk_dqdbheader *)buf;
+	ret = check_dquot_block_header(info, dh);
+	if (ret)
+		goto out_buf;
 	le16_add_cpu(&dh->dqdh_entries, -1);
 	if (!le16_to_cpu(dh->dqdh_entries)) {	/* Block got free? */
 		ret = remove_free_dqentry(info, buf, blk);
@@ -479,6 +518,13 @@
 		goto out_buf;
 	}
 	newblk = le32_to_cpu(ref[get_index(info, dquot->dq_id, depth)]);
+	if (newblk < QT_TREEOFF || newblk >= info->dqi_blocks) {
+		quota_error(dquot->dq_sb, "Getting block too big (%u >= %u)",
+			    newblk, info->dqi_blocks);
+		ret = -EUCLEAN;
+		goto out_buf;
+	}
+
 	if (depth == info->dqi_qtree_depth - 1) {
 		ret = free_dqentry(info, dquot, newblk);
 		newblk = 0;
@@ -578,6 +624,13 @@
 	blk = le32_to_cpu(ref[get_index(info, dquot->dq_id, depth)]);
 	if (!blk)	/* No reference? */
 		goto out_buf;
+	if (blk < QT_TREEOFF || blk >= info->dqi_blocks) {
+		quota_error(dquot->dq_sb, "Getting block too big (%u >= %u)",
+			    blk, info->dqi_blocks);
+		ret = -EUCLEAN;
+		goto out_buf;
+	}
+
 	if (depth < info->dqi_qtree_depth - 1)
 		ret = find_tree_dqentry(info, dquot, blk, depth+1);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ramfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ramfs/inode.c
@@ -274,7 +274,7 @@
 	return 0;
 }
 
-static void ramfs_kill_sb(struct super_block *sb)
+void ramfs_kill_sb(struct super_block *sb)
 {
 	kfree(sb->s_fs_info);
 	kill_litter_super(sb);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/read_write.c
+++ linux-xilinx-zynqmp-5.15.0/fs/read_write.c
@@ -492,6 +492,7 @@
 	inc_syscr(current);
 	return ret;
 }
+EXPORT_SYMBOL_GPL(vfs_read);
 
 static ssize_t new_sync_write(struct file *filp, const char __user *buf, size_t len, loff_t *ppos)
 {
@@ -602,6 +603,7 @@
 	file_end_write(file);
 	return ret;
 }
+EXPORT_SYMBOL_GPL(vfs_write);
 
 /* file_ppos returns &file->f_pos or NULL if file is stream */
 static inline loff_t *file_ppos(struct file *file)
@@ -1250,6 +1252,9 @@
 					  count, fl);
 		file_end_write(out.file);
 	} else {
+		if (out.file->f_flags & O_NONBLOCK)
+			fl |= SPLICE_F_NONBLOCK;
+
 		retval = splice_file_to_pipe(in.file, opipe, &pos, count, fl);
 	}
 
@@ -1384,28 +1389,6 @@
 }
 EXPORT_SYMBOL(generic_copy_file_range);
 
-static ssize_t do_copy_file_range(struct file *file_in, loff_t pos_in,
-				  struct file *file_out, loff_t pos_out,
-				  size_t len, unsigned int flags)
-{
-	/*
-	 * Although we now allow filesystems to handle cross sb copy, passing
-	 * a file of the wrong filesystem type to filesystem driver can result
-	 * in an attempt to dereference the wrong type of ->private_data, so
-	 * avoid doing that until we really have a good reason.  NFS defines
-	 * several different file_system_type structures, but they all end up
-	 * using the same ->copy_file_range() function pointer.
-	 */
-	if (file_out->f_op->copy_file_range &&
-	    file_out->f_op->copy_file_range == file_in->f_op->copy_file_range)
-		return file_out->f_op->copy_file_range(file_in, pos_in,
-						       file_out, pos_out,
-						       len, flags);
-
-	return generic_copy_file_range(file_in, pos_in, file_out, pos_out, len,
-				       flags);
-}
-
 /*
  * Performs necessary checks before doing a file copy
  *
@@ -1427,6 +1410,26 @@
 	if (ret)
 		return ret;
 
+	/*
+	 * We allow some filesystems to handle cross sb copy, but passing
+	 * a file of the wrong filesystem type to filesystem driver can result
+	 * in an attempt to dereference the wrong type of ->private_data, so
+	 * avoid doing that until we really have a good reason.
+	 *
+	 * nfs and cifs define several different file_system_type structures
+	 * and several different sets of file_operations, but they all end up
+	 * using the same ->copy_file_range() function pointer.
+	 */
+	if (flags & COPY_FILE_SPLICE) {
+		/* cross sb splice is allowed */
+	} else if (file_out->f_op->copy_file_range) {
+		if (file_in->f_op->copy_file_range !=
+		    file_out->f_op->copy_file_range)
+			return -EXDEV;
+	} else if (file_inode(file_in)->i_sb != file_inode(file_out)->i_sb) {
+		return -EXDEV;
+	}
+
 	/* Don't touch certain kinds of inodes */
 	if (IS_IMMUTABLE(inode_out))
 		return -EPERM;
@@ -1469,8 +1472,9 @@
 			    size_t len, unsigned int flags)
 {
 	ssize_t ret;
+	bool splice = flags & COPY_FILE_SPLICE;
 
-	if (flags != 0)
+	if (flags & ~COPY_FILE_SPLICE)
 		return -EINVAL;
 
 	ret = generic_copy_file_checks(file_in, pos_in, file_out, pos_out, &len,
@@ -1492,26 +1496,43 @@
 	file_start_write(file_out);
 
 	/*
-	 * Try cloning first, this is supported by more file systems, and
-	 * more efficient if both clone and copy are supported (e.g. NFS).
+	 * Cloning is supported by more file systems, so we implement copy on
+	 * same sb using clone, but for filesystems where both clone and copy
+	 * are supported (e.g. nfs,cifs), we only call the copy method.
 	 */
-	if (file_in->f_op->remap_file_range &&
-	    file_inode(file_in)->i_sb == file_inode(file_out)->i_sb) {
-		loff_t cloned;
+	if (!splice && file_out->f_op->copy_file_range) {
+		ret = file_out->f_op->copy_file_range(file_in, pos_in,
+						      file_out, pos_out,
+						      len, flags);
+		goto done;
+	}
 
-		cloned = file_in->f_op->remap_file_range(file_in, pos_in,
+	if (!splice && file_in->f_op->remap_file_range &&
+	    file_inode(file_in)->i_sb == file_inode(file_out)->i_sb) {
+		ret = file_in->f_op->remap_file_range(file_in, pos_in,
 				file_out, pos_out,
 				min_t(loff_t, MAX_RW_COUNT, len),
 				REMAP_FILE_CAN_SHORTEN);
-		if (cloned > 0) {
-			ret = cloned;
+		if (ret > 0)
 			goto done;
-		}
 	}
 
-	ret = do_copy_file_range(file_in, pos_in, file_out, pos_out, len,
-				flags);
-	WARN_ON_ONCE(ret == -EOPNOTSUPP);
+	/*
+	 * We can get here for same sb copy of filesystems that do not implement
+	 * ->copy_file_range() in case filesystem does not support clone or in
+	 * case filesystem supports clone but rejected the clone request (e.g.
+	 * because it was not block aligned).
+	 *
+	 * In both cases, fall back to kernel copy so we are able to maintain a
+	 * consistent story about which filesystems support copy_file_range()
+	 * and which filesystems do not, that will allow userspace tools to
+	 * make consistent desicions w.r.t using copy_file_range().
+	 *
+	 * We also get here if caller (e.g. nfsd) requested COPY_FILE_SPLICE.
+	 */
+	ret = generic_copy_file_range(file_in, pos_in, file_out, pos_out, len,
+				      flags);
+
 done:
 	if (ret > 0) {
 		fsnotify_access(file_in);
@@ -1562,6 +1583,10 @@
 		pos_out = f_out.file->f_pos;
 	}
 
+	ret = -EINVAL;
+	if (flags != 0)
+		goto out;
+
 	ret = vfs_copy_file_range(f_in.file, pos_in, f_out.file, pos_out, len,
 				  flags);
 	if (ret > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/reiserfs/journal.c
+++ linux-xilinx-zynqmp-5.15.0/fs/reiserfs/journal.c
@@ -2323,7 +2323,7 @@
 	int i, j;
 
 	bh = __getblk(dev, block, bufsize);
-	if (buffer_uptodate(bh))
+	if (!bh || buffer_uptodate(bh))
 		return (bh);
 
 	if (block + BUFNR > max_block) {
@@ -2333,6 +2333,8 @@
 	j = 1;
 	for (i = 1; i < blocks; i++) {
 		bh = __getblk(dev, block + i, bufsize);
+		if (!bh)
+			break;
 		if (buffer_uptodate(bh)) {
 			brelse(bh);
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/reiserfs/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/reiserfs/namei.c
@@ -696,6 +696,7 @@
 
 out_failed:
 	reiserfs_write_unlock(dir->i_sb);
+	reiserfs_security_free(&security);
 	return retval;
 }
 
@@ -779,6 +780,7 @@
 
 out_failed:
 	reiserfs_write_unlock(dir->i_sb);
+	reiserfs_security_free(&security);
 	return retval;
 }
 
@@ -878,6 +880,7 @@
 	retval = journal_end(&th);
 out_failed:
 	reiserfs_write_unlock(dir->i_sb);
+	reiserfs_security_free(&security);
 	return retval;
 }
 
@@ -1194,6 +1197,7 @@
 	retval = journal_end(&th);
 out_failed:
 	reiserfs_write_unlock(parent_dir->i_sb);
+	reiserfs_security_free(&security);
 	return retval;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/reiserfs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/reiserfs/super.c
@@ -1437,7 +1437,6 @@
 	unsigned long safe_mask = 0;
 	unsigned int commit_max_age = (unsigned int)-1;
 	struct reiserfs_journal *journal = SB_JOURNAL(s);
-	char *new_opts;
 	int err;
 	char *qf_names[REISERFS_MAXQUOTAS];
 	unsigned int qfmt = 0;
@@ -1445,10 +1444,6 @@
 	int i;
 #endif
 
-	new_opts = kstrdup(arg, GFP_KERNEL);
-	if (arg && !new_opts)
-		return -ENOMEM;
-
 	sync_filesystem(s);
 	reiserfs_write_lock(s);
 
@@ -1599,7 +1594,6 @@
 out_err_unlock:
 	reiserfs_write_unlock(s);
 out_err:
-	kfree(new_opts);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/reiserfs/xattr_security.c
+++ linux-xilinx-zynqmp-5.15.0/fs/reiserfs/xattr_security.c
@@ -50,6 +50,7 @@
 	int error;
 
 	sec->name = NULL;
+	sec->value = NULL;
 
 	/* Don't add selinux attributes on xattrs - they'll never get used */
 	if (IS_PRIVATE(dir))
@@ -81,11 +82,15 @@
 			    struct inode *inode,
 			    struct reiserfs_security_handle *sec)
 {
+	char xattr_name[XATTR_NAME_MAX + 1] = XATTR_SECURITY_PREFIX;
 	int error;
-	if (strlen(sec->name) < sizeof(XATTR_SECURITY_PREFIX))
+
+	if (XATTR_SECURITY_PREFIX_LEN + strlen(sec->name) > XATTR_NAME_MAX)
 		return -EINVAL;
 
-	error = reiserfs_xattr_set_handle(th, inode, sec->name, sec->value,
+	strlcat(xattr_name, sec->name, sizeof(xattr_name));
+
+	error = reiserfs_xattr_set_handle(th, inode, xattr_name, sec->value,
 					  sec->length, XATTR_CREATE);
 	if (error == -ENODATA || error == -EOPNOTSUPP)
 		error = 0;
@@ -95,7 +100,6 @@
 
 void reiserfs_security_free(struct reiserfs_security_handle *sec)
 {
-	kfree(sec->name);
 	kfree(sec->value);
 	sec->name = NULL;
 	sec->value = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/remap_range.c
+++ linux-xilinx-zynqmp-5.15.0/fs/remap_range.c
@@ -71,7 +71,8 @@
 	 * Otherwise, make sure the count is also block-aligned, having
 	 * already confirmed the starting offsets' block alignment.
 	 */
-	if (pos_in + count == size_in) {
+	if (pos_in + count == size_in &&
+	    (!(remap_flags & REMAP_FILE_DEDUP) || pos_out + count == size_out)) {
 		bcount = ALIGN(size_in, bs) - pos_in;
 	} else {
 		if (!IS_ALIGNED(count, bs))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/select.c
+++ linux-xilinx-zynqmp-5.15.0/fs/select.c
@@ -458,9 +458,11 @@
 	return max;
 }
 
-#define POLLIN_SET (EPOLLRDNORM | EPOLLRDBAND | EPOLLIN | EPOLLHUP | EPOLLERR)
-#define POLLOUT_SET (EPOLLWRBAND | EPOLLWRNORM | EPOLLOUT | EPOLLERR)
-#define POLLEX_SET (EPOLLPRI)
+#define POLLIN_SET (EPOLLRDNORM | EPOLLRDBAND | EPOLLIN | EPOLLHUP | EPOLLERR |\
+			EPOLLNVAL)
+#define POLLOUT_SET (EPOLLWRBAND | EPOLLWRNORM | EPOLLOUT | EPOLLERR |\
+			 EPOLLNVAL)
+#define POLLEX_SET (EPOLLPRI | EPOLLNVAL)
 
 static inline void wait_key_set(poll_table *wait, unsigned long in,
 				unsigned long out, unsigned long bit,
@@ -473,7 +475,7 @@
 		wait->_key |= POLLOUT_SET;
 }
 
-static int do_select(int n, fd_set_bits *fds, struct timespec64 *end_time)
+static noinline_for_stack int do_select(int n, fd_set_bits *fds, struct timespec64 *end_time)
 {
 	ktime_t expire, *to = NULL;
 	struct poll_wqueues table;
@@ -527,6 +529,7 @@
 					break;
 				if (!(bit & all_bits))
 					continue;
+				mask = EPOLLNVAL;
 				f = fdget(i);
 				if (f.file) {
 					wait_key_set(wait, in, out, bit,
@@ -534,34 +537,34 @@
 					mask = vfs_poll(f.file, wait);
 
 					fdput(f);
-					if ((mask & POLLIN_SET) && (in & bit)) {
-						res_in |= bit;
-						retval++;
-						wait->_qproc = NULL;
-					}
-					if ((mask & POLLOUT_SET) && (out & bit)) {
-						res_out |= bit;
-						retval++;
-						wait->_qproc = NULL;
-					}
-					if ((mask & POLLEX_SET) && (ex & bit)) {
-						res_ex |= bit;
-						retval++;
-						wait->_qproc = NULL;
-					}
-					/* got something, stop busy polling */
-					if (retval) {
-						can_busy_loop = false;
-						busy_flag = 0;
-
-					/*
-					 * only remember a returned
-					 * POLL_BUSY_LOOP if we asked for it
-					 */
-					} else if (busy_flag & mask)
-						can_busy_loop = true;
-
 				}
+				if ((mask & POLLIN_SET) && (in & bit)) {
+					res_in |= bit;
+					retval++;
+					wait->_qproc = NULL;
+				}
+				if ((mask & POLLOUT_SET) && (out & bit)) {
+					res_out |= bit;
+					retval++;
+					wait->_qproc = NULL;
+				}
+				if ((mask & POLLEX_SET) && (ex & bit)) {
+					res_ex |= bit;
+					retval++;
+					wait->_qproc = NULL;
+				}
+				/* got something, stop busy polling */
+				if (retval) {
+					can_busy_loop = false;
+					busy_flag = 0;
+
+				/*
+				 * only remember a returned
+				 * POLL_BUSY_LOOP if we asked for it
+				 */
+				} else if (busy_flag & mask)
+					can_busy_loop = true;
+
 			}
 			if (res_in)
 				*rinp = res_in;
@@ -784,7 +787,7 @@
 	}
 	return 0;
 Efault:
-	user_access_end();
+	user_read_access_end();
 	return -EFAULT;
 }
 
@@ -1357,7 +1360,7 @@
 	}
 	return 0;
 Efault:
-	user_access_end();
+	user_read_access_end();
 	return -EFAULT;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/seq_file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/seq_file.c
@@ -947,6 +947,38 @@
 }
 EXPORT_SYMBOL(seq_list_next);
 
+struct list_head *seq_list_start_rcu(struct list_head *head, loff_t pos)
+{
+	struct list_head *lh;
+
+	list_for_each_rcu(lh, head)
+		if (pos-- == 0)
+			return lh;
+
+	return NULL;
+}
+EXPORT_SYMBOL(seq_list_start_rcu);
+
+struct list_head *seq_list_start_head_rcu(struct list_head *head, loff_t pos)
+{
+	if (!pos)
+		return head;
+
+	return seq_list_start_rcu(head, pos - 1);
+}
+EXPORT_SYMBOL(seq_list_start_head_rcu);
+
+struct list_head *seq_list_next_rcu(void *v, struct list_head *head,
+				    loff_t *ppos)
+{
+	struct list_head *lh;
+
+	lh = list_next_rcu((struct list_head *)v);
+	++*ppos;
+	return lh == head ? NULL : lh;
+}
+EXPORT_SYMBOL(seq_list_next_rcu);
+
 /**
  * seq_hlist_start - start an iteration of a hlist
  * @head: the head of the hlist
--- linux-xilinx-zynqmp-5.15.0.orig/fs/shiftfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/shiftfs.c
@@ -0,0 +1,2203 @@
+#include <linux/btrfs.h>
+#include <linux/capability.h>
+#include <linux/cred.h>
+#include <linux/mount.h>
+#include <linux/fdtable.h>
+#include <linux/file.h>
+#include <linux/fs.h>
+#include <linux/namei.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/magic.h>
+#include <linux/parser.h>
+#include <linux/security.h>
+#include <linux/seq_file.h>
+#include <linux/statfs.h>
+#include <linux/slab.h>
+#include <linux/user_namespace.h>
+#include <linux/uidgid.h>
+#include <linux/xattr.h>
+#include <linux/posix_acl.h>
+#include <linux/posix_acl_xattr.h>
+#include <linux/uio.h>
+#include <linux/fiemap.h>
+
+struct shiftfs_super_info {
+	struct vfsmount *mnt;
+	struct user_namespace *userns;
+	/* creds of process who created the super block */
+	const struct cred *creator_cred;
+	bool mark;
+	unsigned int passthrough;
+	unsigned int passthrough_mark;
+};
+
+static void shiftfs_fill_inode(struct inode *inode, unsigned long ino,
+			       umode_t mode, dev_t dev, struct dentry *dentry);
+
+#define SHIFTFS_PASSTHROUGH_NONE 0
+#define SHIFTFS_PASSTHROUGH_STAT 1
+#define SHIFTFS_PASSTHROUGH_IOCTL 2
+#define SHIFTFS_PASSTHROUGH_ALL                                                \
+	(SHIFTFS_PASSTHROUGH_STAT | SHIFTFS_PASSTHROUGH_IOCTL)
+
+static inline bool shiftfs_passthrough_ioctls(struct shiftfs_super_info *info)
+{
+	if (!(info->passthrough & SHIFTFS_PASSTHROUGH_IOCTL))
+		return false;
+
+	return true;
+}
+
+static inline bool shiftfs_passthrough_statfs(struct shiftfs_super_info *info)
+{
+	if (!(info->passthrough & SHIFTFS_PASSTHROUGH_STAT))
+		return false;
+
+	return true;
+}
+
+enum {
+	OPT_MARK,
+	OPT_PASSTHROUGH,
+	OPT_LAST,
+};
+
+/* global filesystem options */
+static const match_table_t tokens = {
+	{ OPT_MARK, "mark" },
+	{ OPT_PASSTHROUGH, "passthrough=%u" },
+	{ OPT_LAST, NULL }
+};
+
+static const struct cred *shiftfs_override_creds(const struct super_block *sb)
+{
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+
+	return override_creds(sbinfo->creator_cred);
+}
+
+static inline void shiftfs_revert_object_creds(const struct cred *oldcred,
+					       struct cred *newcred)
+{
+	revert_creds(oldcred);
+	put_cred(newcred);
+}
+
+static kuid_t shift_kuid(struct user_namespace *from, struct user_namespace *to,
+			 kuid_t kuid)
+{
+	uid_t uid = from_kuid(from, kuid);
+	return make_kuid(to, uid);
+}
+
+static kgid_t shift_kgid(struct user_namespace *from, struct user_namespace *to,
+			 kgid_t kgid)
+{
+	gid_t gid = from_kgid(from, kgid);
+	return make_kgid(to, gid);
+}
+
+static int shiftfs_override_object_creds(const struct super_block *sb,
+					 const struct cred **oldcred,
+					 struct cred **newcred,
+					 struct dentry *dentry, umode_t mode,
+					 bool hardlink)
+{
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+	kuid_t fsuid = current_fsuid();
+	kgid_t fsgid = current_fsgid();
+
+	*oldcred = shiftfs_override_creds(sb);
+
+	*newcred = prepare_creds();
+	if (!*newcred) {
+		revert_creds(*oldcred);
+		return -ENOMEM;
+	}
+
+	(*newcred)->fsuid = shift_kuid(sb->s_user_ns, sbinfo->userns, fsuid);
+	(*newcred)->fsgid = shift_kgid(sb->s_user_ns, sbinfo->userns, fsgid);
+
+	if (!hardlink) {
+		int err = security_dentry_create_files_as(dentry, mode,
+							  &dentry->d_name,
+							  *oldcred, *newcred);
+		if (err) {
+			shiftfs_revert_object_creds(*oldcred, *newcred);
+			return err;
+		}
+	}
+
+	put_cred(override_creds(*newcred));
+	return 0;
+}
+
+static void shiftfs_copyattr(struct inode *from, struct inode *to)
+{
+	struct user_namespace *from_ns = from->i_sb->s_user_ns;
+	struct user_namespace *to_ns = to->i_sb->s_user_ns;
+
+	to->i_uid = shift_kuid(from_ns, to_ns, from->i_uid);
+	to->i_gid = shift_kgid(from_ns, to_ns, from->i_gid);
+	to->i_mode = from->i_mode;
+	to->i_atime = from->i_atime;
+	to->i_mtime = from->i_mtime;
+	to->i_ctime = from->i_ctime;
+	i_size_write(to, i_size_read(from));
+}
+
+static void shiftfs_copyflags(struct inode *from, struct inode *to)
+{
+	unsigned int mask = S_SYNC | S_IMMUTABLE | S_APPEND | S_NOATIME;
+
+	inode_set_flags(to, from->i_flags & mask, mask);
+}
+
+static void shiftfs_file_accessed(struct file *file)
+{
+	struct inode *upperi, *loweri;
+
+	if (file->f_flags & O_NOATIME)
+		return;
+
+	upperi = file_inode(file);
+	loweri = upperi->i_private;
+
+	if (!loweri)
+		return;
+
+	upperi->i_mtime = loweri->i_mtime;
+	upperi->i_ctime = loweri->i_ctime;
+
+	touch_atime(&file->f_path);
+}
+
+static int shiftfs_parse_mount_options(struct shiftfs_super_info *sbinfo,
+				       char *options)
+{
+	char *p;
+	substring_t args[MAX_OPT_ARGS];
+
+	sbinfo->mark = false;
+	sbinfo->passthrough = 0;
+
+	while ((p = strsep(&options, ",")) != NULL) {
+		int err, intarg, token;
+
+		if (!*p)
+			continue;
+
+		token = match_token(p, tokens, args);
+		switch (token) {
+		case OPT_MARK:
+			sbinfo->mark = true;
+			break;
+		case OPT_PASSTHROUGH:
+			err = match_int(&args[0], &intarg);
+			if (err)
+				return err;
+
+			if (intarg & ~SHIFTFS_PASSTHROUGH_ALL)
+				return -EINVAL;
+
+			sbinfo->passthrough = intarg;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static void shiftfs_d_release(struct dentry *dentry)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+
+	if (lowerd)
+		dput(lowerd);
+}
+
+static struct dentry *shiftfs_d_real(struct dentry *dentry,
+				     const struct inode *inode)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+
+	if (inode && d_inode(dentry) == inode)
+		return dentry;
+
+	lowerd = d_real(lowerd, inode);
+	if (lowerd && (!inode || inode == d_inode(lowerd)))
+		return lowerd;
+
+	WARN(1, "shiftfs_d_real(%pd4, %s:%lu): real dentry not found\n", dentry,
+	     inode ? inode->i_sb->s_id : "NULL", inode ? inode->i_ino : 0);
+	return dentry;
+}
+
+static int shiftfs_d_weak_revalidate(struct dentry *dentry, unsigned int flags)
+{
+	int err = 1;
+	struct dentry *lowerd = dentry->d_fsdata;
+
+	if (d_is_negative(lowerd) != d_is_negative(dentry))
+		return 0;
+
+	if ((lowerd->d_flags & DCACHE_OP_WEAK_REVALIDATE))
+		err = lowerd->d_op->d_weak_revalidate(lowerd, flags);
+
+	if (d_really_is_positive(dentry)) {
+		struct inode *inode = d_inode(dentry);
+		struct inode *loweri = d_inode(lowerd);
+
+		shiftfs_copyattr(loweri, inode);
+	}
+
+	return err;
+}
+
+static int shiftfs_d_revalidate(struct dentry *dentry, unsigned int flags)
+{
+	int err = 1;
+	struct dentry *lowerd = dentry->d_fsdata;
+
+	if (d_unhashed(lowerd) ||
+	    ((d_is_negative(lowerd) != d_is_negative(dentry))))
+		return 0;
+
+	if (flags & LOOKUP_RCU)
+		return -ECHILD;
+
+	if ((lowerd->d_flags & DCACHE_OP_REVALIDATE))
+		err = lowerd->d_op->d_revalidate(lowerd, flags);
+
+	if (d_really_is_positive(dentry)) {
+		struct inode *inode = d_inode(dentry);
+		struct inode *loweri = d_inode(lowerd);
+
+		shiftfs_copyattr(loweri, inode);
+	}
+
+	return err;
+}
+
+static const struct dentry_operations shiftfs_dentry_ops = {
+	.d_release	   = shiftfs_d_release,
+	.d_real		   = shiftfs_d_real,
+	.d_revalidate	   = shiftfs_d_revalidate,
+	.d_weak_revalidate = shiftfs_d_weak_revalidate,
+};
+
+static const char *shiftfs_get_link(struct dentry *dentry, struct inode *inode,
+				    struct delayed_call *done)
+{
+	const char *p;
+	const struct cred *oldcred;
+	struct dentry *lowerd;
+
+	/* RCU lookup not supported */
+	if (!dentry)
+		return ERR_PTR(-ECHILD);
+
+	lowerd = dentry->d_fsdata;
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	p = vfs_get_link(lowerd, done);
+	revert_creds(oldcred);
+
+	return p;
+}
+
+static int shiftfs_setxattr(struct dentry *dentry, struct inode *inode,
+			    const char *name, const void *value,
+			    size_t size, int flags)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+	int err;
+	const struct cred *oldcred;
+
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	err = vfs_setxattr(&init_user_ns, lowerd, name, value, size, flags);
+	revert_creds(oldcred);
+
+	shiftfs_copyattr(lowerd->d_inode, inode);
+
+	return err;
+}
+
+static int shiftfs_xattr_get(const struct xattr_handler *handler,
+			     struct dentry *dentry, struct inode *inode,
+			     const char *name, void *value, size_t size)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+	int err;
+	const struct cred *oldcred;
+
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	err = vfs_getxattr(&init_user_ns, lowerd, name, value, size);
+	revert_creds(oldcred);
+
+	return err;
+}
+
+static ssize_t shiftfs_listxattr(struct dentry *dentry, char *list,
+				 size_t size)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+	int err;
+	const struct cred *oldcred;
+
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	err = vfs_listxattr(lowerd, list, size);
+	revert_creds(oldcred);
+
+	return err;
+}
+
+static int shiftfs_removexattr(struct user_namespace *ns,
+			       struct dentry *dentry, const char *name)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+	int err;
+	const struct cred *oldcred;
+
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	err = vfs_removexattr(&init_user_ns, lowerd, name);
+	revert_creds(oldcred);
+
+	/* update c/mtime */
+	shiftfs_copyattr(lowerd->d_inode, d_inode(dentry));
+
+	return err;
+}
+
+static int shiftfs_xattr_set(const struct xattr_handler *handler,
+			     struct user_namespace *ns,
+			     struct dentry *dentry, struct inode *inode,
+			     const char *name, const void *value, size_t size,
+			     int flags)
+{
+	if (!value)
+		return shiftfs_removexattr(&init_user_ns, dentry, name);
+	return shiftfs_setxattr(dentry, inode, name, value, size, flags);
+}
+
+static int shiftfs_inode_test(struct inode *inode, void *data)
+{
+	return inode->i_private == data;
+}
+
+static int shiftfs_inode_set(struct inode *inode, void *data)
+{
+	inode->i_private = data;
+	return 0;
+}
+
+static int shiftfs_create_object(struct inode *diri, struct dentry *dentry,
+				 umode_t mode, const char *symlink,
+				 struct dentry *hardlink, bool excl)
+{
+	int err;
+	const struct cred *oldcred;
+	struct cred *newcred;
+	void *loweri_iop_ptr = NULL;
+	umode_t modei = mode;
+	struct super_block *dir_sb = diri->i_sb;
+	struct dentry *lowerd_new = dentry->d_fsdata;
+	struct inode *inode = NULL, *loweri_dir = diri->i_private;
+	const struct inode_operations *loweri_dir_iop = loweri_dir->i_op;
+	struct dentry *lowerd_link = NULL;
+
+	inode_lock_nested(loweri_dir, I_MUTEX_PARENT);
+
+	if (hardlink) {
+		loweri_iop_ptr = loweri_dir_iop->link;
+	} else {
+		switch (mode & S_IFMT) {
+		case S_IFDIR:
+			loweri_iop_ptr = loweri_dir_iop->mkdir;
+			break;
+		case S_IFREG:
+			loweri_iop_ptr = loweri_dir_iop->create;
+			break;
+		case S_IFLNK:
+			loweri_iop_ptr = loweri_dir_iop->symlink;
+			break;
+		case S_IFSOCK:
+			/* fall through */
+		case S_IFIFO:
+			loweri_iop_ptr = loweri_dir_iop->mknod;
+			break;
+		}
+	}
+	if (!loweri_iop_ptr) {
+		err = -EINVAL;
+		goto out_iput;
+	}
+
+	if (!hardlink) {
+		inode = new_inode(dir_sb);
+		if (!inode) {
+			err = -ENOMEM;
+			goto out_iput;
+		}
+
+		/*
+		 * new_inode() will have added the new inode to the super
+		 * block's list of inodes. Further below we will call
+		 * inode_insert5() Which would perform the same operation again
+		 * thereby corrupting the list. To avoid this raise I_CREATING
+		 * in i_state which will cause inode_insert5() to skip this
+		 * step. I_CREATING will be cleared by d_instantiate_new()
+		 * below.
+		 */
+		spin_lock(&inode->i_lock);
+		inode->i_state |= I_CREATING;
+		spin_unlock(&inode->i_lock);
+
+		inode_init_owner(&init_user_ns, inode, diri, mode);
+		modei = inode->i_mode;
+	}
+
+	err = shiftfs_override_object_creds(dentry->d_sb, &oldcred, &newcred,
+					    dentry, modei, hardlink != NULL);
+	if (err)
+		goto out_iput;
+
+	if (hardlink) {
+		lowerd_link = hardlink->d_fsdata;
+		err = vfs_link(lowerd_link, &init_user_ns, loweri_dir, lowerd_new, NULL);
+	} else {
+		switch (modei & S_IFMT) {
+		case S_IFDIR:
+			err = vfs_mkdir(&init_user_ns, loweri_dir, lowerd_new, modei);
+			break;
+		case S_IFREG:
+			err = vfs_create(&init_user_ns, loweri_dir, lowerd_new, modei, excl);
+			break;
+		case S_IFLNK:
+			err = vfs_symlink(&init_user_ns, loweri_dir, lowerd_new, symlink);
+			break;
+		case S_IFSOCK:
+			/* fall through */
+		case S_IFIFO:
+			err = vfs_mknod(&init_user_ns, loweri_dir, lowerd_new, modei, 0);
+			break;
+		default:
+			err = -EINVAL;
+			break;
+		}
+	}
+
+	shiftfs_revert_object_creds(oldcred, newcred);
+
+	if (!err && WARN_ON(!lowerd_new->d_inode))
+		err = -EIO;
+	if (err)
+		goto out_iput;
+
+	if (hardlink) {
+		inode = d_inode(hardlink);
+		ihold(inode);
+
+		/* copy up times from lower inode */
+		shiftfs_copyattr(d_inode(lowerd_link), inode);
+		set_nlink(d_inode(hardlink), d_inode(lowerd_link)->i_nlink);
+		d_instantiate(dentry, inode);
+	} else {
+		struct inode *inode_tmp;
+		struct inode *loweri_new = d_inode(lowerd_new);
+
+		inode_tmp = inode_insert5(inode, (unsigned long)loweri_new,
+					  shiftfs_inode_test, shiftfs_inode_set,
+					  loweri_new);
+		if (unlikely(inode_tmp != inode)) {
+			pr_err_ratelimited("shiftfs: newly created inode found in cache\n");
+			iput(inode_tmp);
+			err = -EINVAL;
+			goto out_iput;
+		}
+
+		ihold(loweri_new);
+		shiftfs_fill_inode(inode, loweri_new->i_ino, loweri_new->i_mode,
+				   0, lowerd_new);
+		d_instantiate_new(dentry, inode);
+	}
+
+	shiftfs_copyattr(loweri_dir, diri);
+	if (loweri_iop_ptr == loweri_dir_iop->mkdir)
+		set_nlink(diri, loweri_dir->i_nlink);
+
+	inode = NULL;
+
+out_iput:
+	iput(inode);
+	inode_unlock(loweri_dir);
+
+	return err;
+}
+
+static int shiftfs_create(struct user_namespace *ns,
+			  struct inode *dir, struct dentry *dentry,
+			  umode_t mode,  bool excl)
+{
+	mode |= S_IFREG;
+
+	return shiftfs_create_object(dir, dentry, mode, NULL, NULL, excl);
+}
+
+static int shiftfs_mkdir(struct user_namespace *ns, struct inode *dir, struct dentry *dentry,
+			 umode_t mode)
+{
+	mode |= S_IFDIR;
+
+	return shiftfs_create_object(dir, dentry, mode, NULL, NULL, false);
+}
+
+static int shiftfs_link(struct dentry *hardlink, struct inode *dir,
+			struct dentry *dentry)
+{
+	return shiftfs_create_object(dir, dentry, 0, NULL, hardlink, false);
+}
+
+static int shiftfs_mknod(struct user_namespace *ns,
+			 struct inode *dir, struct dentry *dentry, umode_t mode,
+			 dev_t rdev)
+{
+	if (!S_ISFIFO(mode) && !S_ISSOCK(mode))
+		return -EPERM;
+
+	return shiftfs_create_object(dir, dentry, mode, NULL, NULL, false);
+}
+
+static int shiftfs_symlink(struct user_namespace *ns, struct inode *dir, struct dentry *dentry,
+			   const char *symlink)
+{
+	return shiftfs_create_object(dir, dentry, S_IFLNK, symlink, NULL, false);
+}
+
+static int shiftfs_rm(struct inode *dir, struct dentry *dentry, bool rmdir)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+	struct inode *loweri = dir->i_private;
+	struct inode *inode = d_inode(dentry);
+	int err;
+	const struct cred *oldcred;
+
+	dget(lowerd);
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	inode_lock_nested(loweri, I_MUTEX_PARENT);
+	if (rmdir)
+		err = vfs_rmdir(&init_user_ns, loweri, lowerd);
+	else
+		err = vfs_unlink(&init_user_ns, loweri, lowerd, NULL);
+	revert_creds(oldcred);
+
+	if (!err) {
+		d_drop(dentry);
+
+		if (rmdir)
+			clear_nlink(inode);
+		else
+			drop_nlink(inode);
+	}
+	inode_unlock(loweri);
+
+	shiftfs_copyattr(loweri, dir);
+	dput(lowerd);
+
+	return err;
+}
+
+static int shiftfs_unlink(struct inode *dir, struct dentry *dentry)
+{
+	return shiftfs_rm(dir, dentry, false);
+}
+
+static int shiftfs_rmdir(struct inode *dir, struct dentry *dentry)
+{
+	return shiftfs_rm(dir, dentry, true);
+}
+
+static int shiftfs_rename(struct user_namespace *ns,
+			  struct inode *olddir, struct dentry *old,
+			  struct inode *newdir, struct dentry *new,
+			  unsigned int flags)
+{
+	struct dentry *lowerd_dir_old = old->d_parent->d_fsdata,
+		      *lowerd_dir_new = new->d_parent->d_fsdata,
+		      *lowerd_old = old->d_fsdata, *lowerd_new = new->d_fsdata,
+		      *trapd;
+	struct inode *loweri_dir_old = lowerd_dir_old->d_inode,
+		     *loweri_dir_new = lowerd_dir_new->d_inode;
+	struct renamedata rd = {
+		.old_mnt_userns	= &init_user_ns,
+		.old_dir	= loweri_dir_old,
+		.old_dentry	= lowerd_old,
+		.new_mnt_userns	= &init_user_ns,
+		.new_dir	= loweri_dir_new,
+		.new_dentry	= lowerd_new,
+	};
+	int err = -EINVAL;
+	const struct cred *oldcred;
+
+	trapd = lock_rename(lowerd_dir_new, lowerd_dir_old);
+
+	if (trapd == lowerd_old || trapd == lowerd_new)
+		goto out_unlock;
+
+	oldcred = shiftfs_override_creds(old->d_sb);
+	err = vfs_rename(&rd);
+	revert_creds(oldcred);
+
+	shiftfs_copyattr(loweri_dir_old, olddir);
+	shiftfs_copyattr(loweri_dir_new, newdir);
+
+out_unlock:
+	unlock_rename(lowerd_dir_new, lowerd_dir_old);
+
+	return err;
+}
+
+static struct dentry *shiftfs_lookup(struct inode *dir, struct dentry *dentry,
+				     unsigned int flags)
+{
+	struct dentry *new;
+	struct inode *newi;
+	const struct cred *oldcred;
+	struct dentry *lowerd = dentry->d_parent->d_fsdata;
+	struct inode *inode = NULL, *loweri = lowerd->d_inode;
+
+	inode_lock(loweri);
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	new = lookup_one_len(dentry->d_name.name, lowerd, dentry->d_name.len);
+	revert_creds(oldcred);
+	inode_unlock(loweri);
+
+	if (IS_ERR(new))
+		return new;
+
+	dentry->d_fsdata = new;
+
+	newi = new->d_inode;
+	if (!newi)
+		goto out;
+
+	inode = iget5_locked(dentry->d_sb, (unsigned long)newi,
+			     shiftfs_inode_test, shiftfs_inode_set, newi);
+	if (!inode) {
+		dput(new);
+		return ERR_PTR(-ENOMEM);
+	}
+	if (inode->i_state & I_NEW) {
+		/*
+		 * inode->i_private set by shiftfs_inode_set(), but we still
+		 * need to take a reference
+		*/
+		ihold(newi);
+		shiftfs_fill_inode(inode, newi->i_ino, newi->i_mode, 0, new);
+		unlock_new_inode(inode);
+	}
+
+out:
+	return d_splice_alias(inode, dentry);
+}
+
+static int shiftfs_permission(struct user_namespace *ns, struct inode *inode, int mask)
+{
+	int err;
+	const struct cred *oldcred;
+	struct inode *loweri = inode->i_private;
+
+	if (!loweri) {
+		WARN_ON(!(mask & MAY_NOT_BLOCK));
+		return -ECHILD;
+	}
+
+	err = generic_permission(&init_user_ns, inode, mask);
+	if (err)
+		return err;
+
+	oldcred = shiftfs_override_creds(inode->i_sb);
+	err = inode_permission(&init_user_ns, loweri, mask);
+	revert_creds(oldcred);
+
+	return err;
+}
+
+static int shiftfs_fiemap(struct inode *inode,
+			  struct fiemap_extent_info *fieinfo, u64 start,
+			  u64 len)
+{
+	int err;
+	const struct cred *oldcred;
+	struct inode *loweri = inode->i_private;
+
+	if (!loweri->i_op->fiemap)
+		return -EOPNOTSUPP;
+
+	oldcred = shiftfs_override_creds(inode->i_sb);
+	if (fieinfo->fi_flags & FIEMAP_FLAG_SYNC)
+		filemap_write_and_wait(loweri->i_mapping);
+	err = loweri->i_op->fiemap(loweri, fieinfo, start, len);
+	revert_creds(oldcred);
+
+	return err;
+}
+
+static int shiftfs_tmpfile(struct user_namespace *ns,
+			   struct inode *dir, struct dentry *dentry,
+			   umode_t mode)
+{
+	int err;
+	const struct cred *oldcred;
+	struct dentry *lowerd = dentry->d_fsdata;
+	struct inode *loweri = dir->i_private;
+
+	if (!loweri->i_op->tmpfile)
+		return -EOPNOTSUPP;
+
+	oldcred = shiftfs_override_creds(dir->i_sb);
+	err = loweri->i_op->tmpfile(&init_user_ns, loweri, lowerd, mode);
+	revert_creds(oldcred);
+
+	return err;
+}
+
+static int shiftfs_setattr(struct user_namespace *ns, struct dentry *dentry, struct iattr *attr)
+{
+	struct dentry *lowerd = dentry->d_fsdata;
+	struct inode *loweri = lowerd->d_inode;
+	struct iattr newattr;
+	const struct cred *oldcred;
+	struct super_block *sb = dentry->d_sb;
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+	int err;
+
+	err = setattr_prepare(&init_user_ns, dentry, attr);
+	if (err)
+		return err;
+
+	newattr = *attr;
+	newattr.ia_uid = shift_kuid(sb->s_user_ns, sbinfo->userns, attr->ia_uid);
+	newattr.ia_gid = shift_kgid(sb->s_user_ns, sbinfo->userns, attr->ia_gid);
+
+	/*
+	 * mode change is for clearing setuid/setgid bits. Allow lower fs
+	 * to interpret this in its own way.
+	 */
+	if (newattr.ia_valid & (ATTR_KILL_SUID|ATTR_KILL_SGID))
+		newattr.ia_valid &= ~ATTR_MODE;
+
+	inode_lock(loweri);
+	oldcred = shiftfs_override_creds(dentry->d_sb);
+	err = notify_change(&init_user_ns, lowerd, &newattr, NULL);
+	revert_creds(oldcred);
+	inode_unlock(loweri);
+
+	shiftfs_copyattr(loweri, d_inode(dentry));
+
+	return err;
+}
+
+static int shiftfs_getattr(struct user_namespace *ns,
+			   const struct path *path, struct kstat *stat,
+			   u32 request_mask, unsigned int query_flags)
+{
+	struct inode *inode = path->dentry->d_inode;
+	struct dentry *lowerd = path->dentry->d_fsdata;
+	struct inode *loweri = lowerd->d_inode;
+	struct shiftfs_super_info *info = path->dentry->d_sb->s_fs_info;
+	struct path newpath = { .mnt = info->mnt, .dentry = lowerd };
+	struct user_namespace *from_ns = loweri->i_sb->s_user_ns;
+	struct user_namespace *to_ns = inode->i_sb->s_user_ns;
+	const struct cred *oldcred;
+	int err;
+
+	oldcred = shiftfs_override_creds(inode->i_sb);
+	err = vfs_getattr(&newpath, stat, request_mask, query_flags);
+	revert_creds(oldcred);
+
+	if (err)
+		return err;
+
+	/* transform the underlying id */
+	stat->uid = shift_kuid(from_ns, to_ns, stat->uid);
+	stat->gid = shift_kgid(from_ns, to_ns, stat->gid);
+	return 0;
+}
+
+#ifdef CONFIG_SHIFT_FS_POSIX_ACL
+
+static int
+shift_acl_ids(struct user_namespace *from, struct user_namespace *to,
+	      struct posix_acl *acl)
+{
+	int i;
+
+	for (i = 0; i < acl->a_count; i++) {
+		struct posix_acl_entry *e = &acl->a_entries[i];
+		switch(e->e_tag) {
+		case ACL_USER:
+			e->e_uid = shift_kuid(from, to, e->e_uid);
+			if (!uid_valid(e->e_uid))
+				return -EOVERFLOW;
+			break;
+		case ACL_GROUP:
+			e->e_gid = shift_kgid(from, to, e->e_gid);
+			if (!gid_valid(e->e_gid))
+				return -EOVERFLOW;
+			break;
+		}
+	}
+	return 0;
+}
+
+static void
+shift_acl_xattr_ids(struct user_namespace *from, struct user_namespace *to,
+		    void *value, size_t size)
+{
+	struct posix_acl_xattr_header *header = value;
+	struct posix_acl_xattr_entry *entry = (void *)(header + 1), *end;
+	int count;
+	kuid_t kuid;
+	kgid_t kgid;
+
+	if (!value)
+		return;
+	if (size < sizeof(struct posix_acl_xattr_header))
+		return;
+	if (header->a_version != cpu_to_le32(POSIX_ACL_XATTR_VERSION))
+		return;
+
+	count = posix_acl_xattr_count(size);
+	if (count < 0)
+		return;
+	if (count == 0)
+		return;
+
+	for (end = entry + count; entry != end; entry++) {
+		switch(le16_to_cpu(entry->e_tag)) {
+		case ACL_USER:
+			kuid = make_kuid(&init_user_ns, le32_to_cpu(entry->e_id));
+			kuid = shift_kuid(from, to, kuid);
+			entry->e_id = cpu_to_le32(from_kuid(&init_user_ns, kuid));
+			break;
+		case ACL_GROUP:
+			kgid = make_kgid(from, le32_to_cpu(entry->e_id));
+			kgid = shift_kgid(from, to, kgid);
+			entry->e_id = cpu_to_le32(from_kgid(from, kgid));
+			break;
+		default:
+			break;
+		}
+	}
+}
+
+static struct posix_acl *
+shiftfs_get_acl(struct inode *inode, int type, bool rcu)
+{
+	struct inode *loweri = inode->i_private;
+	const struct cred *oldcred;
+	struct posix_acl *lower_acl, *acl = NULL;
+	struct user_namespace *from_ns = loweri->i_sb->s_user_ns;
+	struct user_namespace *to_ns = inode->i_sb->s_user_ns;
+	int size;
+	int err;
+
+	if (rcu)
+		return ERR_PTR(-ECHILD);
+
+	if (!IS_POSIXACL(loweri))
+		return NULL;
+
+	oldcred = shiftfs_override_creds(inode->i_sb);
+	lower_acl = get_acl(loweri, type);
+	revert_creds(oldcred);
+
+	if (lower_acl && !IS_ERR(lower_acl)) {
+		/* XXX: export posix_acl_clone? */
+		size = sizeof(struct posix_acl) +
+		       lower_acl->a_count * sizeof(struct posix_acl_entry);
+		acl = kmemdup(lower_acl, size, GFP_KERNEL);
+		posix_acl_release(lower_acl);
+
+		if (!acl)
+			return ERR_PTR(-ENOMEM);
+
+		refcount_set(&acl->a_refcount, 1);
+
+		err = shift_acl_ids(from_ns, to_ns, acl);
+		if (err) {
+			kfree(acl);
+			return ERR_PTR(err);
+		}
+	}
+
+	return acl;
+}
+
+static int
+shiftfs_posix_acl_xattr_get(const struct xattr_handler *handler,
+			   struct dentry *dentry, struct inode *inode,
+			   const char *name, void *buffer, size_t size)
+{
+	struct inode *loweri = inode->i_private;
+	int ret;
+
+	ret = shiftfs_xattr_get(NULL, dentry, inode, handler->name,
+				buffer, size);
+	if (ret < 0)
+		return ret;
+
+	inode_lock(loweri);
+	shift_acl_xattr_ids(loweri->i_sb->s_user_ns, inode->i_sb->s_user_ns,
+			    buffer, size);
+	inode_unlock(loweri);
+	return ret;
+}
+
+static int
+shiftfs_posix_acl_xattr_set(const struct xattr_handler *handler,
+			    struct user_namespace *ns,
+			    struct dentry *dentry, struct inode *inode,
+			    const char *name, const void *value,
+			    size_t size, int flags)
+{
+	struct inode *loweri = inode->i_private;
+	int err;
+
+	if (!IS_POSIXACL(loweri) || !loweri->i_op->set_acl)
+		return -EOPNOTSUPP;
+	if (handler->flags == ACL_TYPE_DEFAULT && !S_ISDIR(inode->i_mode))
+		return value ? -EACCES : 0;
+	if (!inode_owner_or_capable(&init_user_ns, inode))
+		return -EPERM;
+
+	if (value) {
+		shift_acl_xattr_ids(inode->i_sb->s_user_ns,
+				    loweri->i_sb->s_user_ns,
+				    (void *)value, size);
+		err = shiftfs_setxattr(dentry, inode, handler->name, value,
+				       size, flags);
+	} else {
+		err = shiftfs_removexattr(&init_user_ns, dentry, handler->name);
+	}
+
+	if (!err)
+		shiftfs_copyattr(loweri, inode);
+
+	return err;
+}
+
+static const struct xattr_handler
+shiftfs_posix_acl_access_xattr_handler = {
+	.name = XATTR_NAME_POSIX_ACL_ACCESS,
+	.flags = ACL_TYPE_ACCESS,
+	.get = shiftfs_posix_acl_xattr_get,
+	.set = shiftfs_posix_acl_xattr_set,
+};
+
+static const struct xattr_handler
+shiftfs_posix_acl_default_xattr_handler = {
+	.name = XATTR_NAME_POSIX_ACL_DEFAULT,
+	.flags = ACL_TYPE_DEFAULT,
+	.get = shiftfs_posix_acl_xattr_get,
+	.set = shiftfs_posix_acl_xattr_set,
+};
+
+#else /* !CONFIG_SHIFT_FS_POSIX_ACL */
+
+#define shiftfs_get_acl NULL
+
+#endif /* CONFIG_SHIFT_FS_POSIX_ACL */
+
+static const struct inode_operations shiftfs_dir_inode_operations = {
+	.lookup		= shiftfs_lookup,
+	.mkdir		= shiftfs_mkdir,
+	.symlink	= shiftfs_symlink,
+	.unlink		= shiftfs_unlink,
+	.rmdir		= shiftfs_rmdir,
+	.rename		= shiftfs_rename,
+	.link		= shiftfs_link,
+	.setattr	= shiftfs_setattr,
+	.create		= shiftfs_create,
+	.mknod		= shiftfs_mknod,
+	.permission	= shiftfs_permission,
+	.getattr	= shiftfs_getattr,
+	.listxattr	= shiftfs_listxattr,
+	.get_acl	= shiftfs_get_acl,
+};
+
+static const struct inode_operations shiftfs_file_inode_operations = {
+	.fiemap		= shiftfs_fiemap,
+	.getattr	= shiftfs_getattr,
+	.get_acl	= shiftfs_get_acl,
+	.listxattr	= shiftfs_listxattr,
+	.permission	= shiftfs_permission,
+	.setattr	= shiftfs_setattr,
+	.tmpfile	= shiftfs_tmpfile,
+};
+
+static const struct inode_operations shiftfs_special_inode_operations = {
+	.getattr	= shiftfs_getattr,
+	.get_acl	= shiftfs_get_acl,
+	.listxattr	= shiftfs_listxattr,
+	.permission	= shiftfs_permission,
+	.setattr	= shiftfs_setattr,
+};
+
+static const struct inode_operations shiftfs_symlink_inode_operations = {
+	.getattr	= shiftfs_getattr,
+	.get_link	= shiftfs_get_link,
+	.listxattr	= shiftfs_listxattr,
+	.setattr	= shiftfs_setattr,
+};
+
+static struct file *shiftfs_open_realfile(const struct file *file,
+					  struct inode *realinode)
+{
+	struct file *realfile;
+	const struct cred *old_cred;
+	struct inode *inode = file_inode(file);
+	struct dentry *lowerd = file->f_path.dentry->d_fsdata;
+	struct shiftfs_super_info *info = inode->i_sb->s_fs_info;
+	struct path realpath = { .mnt = info->mnt, .dentry = lowerd };
+
+	old_cred = shiftfs_override_creds(inode->i_sb);
+	realfile = open_with_fake_path(&realpath, file->f_flags, realinode,
+				       info->creator_cred);
+	revert_creds(old_cred);
+
+	return realfile;
+}
+
+#define SHIFTFS_SETFL_MASK (O_APPEND | O_NONBLOCK | O_NDELAY | O_DIRECT)
+
+static int shiftfs_change_flags(struct file *file, unsigned int flags)
+{
+	struct inode *inode = file_inode(file);
+	int err;
+
+	/* if some flag changed that cannot be changed then something's amiss */
+	if (WARN_ON((file->f_flags ^ flags) & ~SHIFTFS_SETFL_MASK))
+		return -EIO;
+
+	flags &= SHIFTFS_SETFL_MASK;
+
+	if (((flags ^ file->f_flags) & O_APPEND) && IS_APPEND(inode))
+		return -EPERM;
+
+	if (flags & O_DIRECT) {
+		if (!file->f_mapping->a_ops ||
+		    !file->f_mapping->a_ops->direct_IO)
+			return -EINVAL;
+	}
+
+	if (file->f_op->check_flags) {
+		err = file->f_op->check_flags(flags);
+		if (err)
+			return err;
+	}
+
+	spin_lock(&file->f_lock);
+	file->f_flags = (file->f_flags & ~SHIFTFS_SETFL_MASK) | flags;
+	spin_unlock(&file->f_lock);
+
+	return 0;
+}
+
+static int shiftfs_open(struct inode *inode, struct file *file)
+{
+	struct file *realfile;
+
+	realfile = shiftfs_open_realfile(file, inode->i_private);
+	if (IS_ERR(realfile))
+		return PTR_ERR(realfile);
+
+	file->private_data = realfile;
+	/* For O_DIRECT dentry_open() checks f_mapping->a_ops->direct_IO. */
+	file->f_mapping = realfile->f_mapping;
+
+	return 0;
+}
+
+static int shiftfs_dir_open(struct inode *inode, struct file *file)
+{
+	struct file *realfile;
+	const struct cred *oldcred;
+	struct dentry *lowerd = file->f_path.dentry->d_fsdata;
+	struct shiftfs_super_info *info = inode->i_sb->s_fs_info;
+	struct path realpath = { .mnt = info->mnt, .dentry = lowerd };
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	realfile = dentry_open(&realpath, file->f_flags | O_NOATIME,
+			       info->creator_cred);
+	revert_creds(oldcred);
+	if (IS_ERR(realfile))
+		return PTR_ERR(realfile);
+
+	file->private_data = realfile;
+
+	return 0;
+}
+
+static int shiftfs_release(struct inode *inode, struct file *file)
+{
+	struct file *realfile = file->private_data;
+
+	if (realfile)
+		fput(realfile);
+
+	return 0;
+}
+
+static int shiftfs_dir_release(struct inode *inode, struct file *file)
+{
+	return shiftfs_release(inode, file);
+}
+
+static loff_t shiftfs_dir_llseek(struct file *file, loff_t offset, int whence)
+{
+	struct file *realfile = file->private_data;
+
+	return vfs_llseek(realfile, offset, whence);
+}
+
+static loff_t shiftfs_file_llseek(struct file *file, loff_t offset, int whence)
+{
+	struct inode *realinode = file_inode(file)->i_private;
+
+	return generic_file_llseek_size(file, offset, whence,
+					realinode->i_sb->s_maxbytes,
+					i_size_read(realinode));
+}
+
+/* XXX: Need to figure out what to to about atime updates, maybe other
+ * timestamps too ... ref. ovl_file_accessed() */
+
+static rwf_t shiftfs_iocb_to_rwf(struct kiocb *iocb)
+{
+	int ifl = iocb->ki_flags;
+	rwf_t flags = 0;
+
+	if (ifl & IOCB_NOWAIT)
+		flags |= RWF_NOWAIT;
+	if (ifl & IOCB_HIPRI)
+		flags |= RWF_HIPRI;
+	if (ifl & IOCB_DSYNC)
+		flags |= RWF_DSYNC;
+	if (ifl & IOCB_SYNC)
+		flags |= RWF_SYNC;
+
+	return flags;
+}
+
+static int shiftfs_real_fdget(const struct file *file, struct fd *lowerfd)
+{
+	struct file *realfile;
+
+	if (file->f_op->open != shiftfs_open &&
+	    file->f_op->open != shiftfs_dir_open)
+		return -EINVAL;
+
+	realfile = file->private_data;
+	lowerfd->flags = 0;
+	lowerfd->file = realfile;
+
+	/* Did the flags change since open? */
+	if (unlikely(file->f_flags & ~lowerfd->file->f_flags))
+		return shiftfs_change_flags(lowerfd->file, file->f_flags);
+
+	return 0;
+}
+
+static ssize_t shiftfs_read_iter(struct kiocb *iocb, struct iov_iter *iter)
+{
+	struct file *file = iocb->ki_filp;
+	struct fd lowerfd;
+	const struct cred *oldcred;
+	ssize_t ret;
+
+	if (!iov_iter_count(iter))
+		return 0;
+
+	ret = shiftfs_real_fdget(file, &lowerfd);
+	if (ret)
+		return ret;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	ret = vfs_iter_read(lowerfd.file, iter, &iocb->ki_pos,
+			    shiftfs_iocb_to_rwf(iocb));
+	revert_creds(oldcred);
+
+	shiftfs_file_accessed(file);
+
+	fdput(lowerfd);
+	return ret;
+}
+
+static ssize_t shiftfs_write_iter(struct kiocb *iocb, struct iov_iter *iter)
+{
+	struct file *file = iocb->ki_filp;
+	struct inode *inode = file_inode(file);
+	struct fd lowerfd;
+	const struct cred *oldcred;
+	ssize_t ret;
+
+	if (!iov_iter_count(iter))
+		return 0;
+
+	inode_lock(inode);
+	/* Update mode */
+	shiftfs_copyattr(inode->i_private, inode);
+	ret = file_remove_privs(file);
+	if (ret)
+		goto out_unlock;
+
+	ret = shiftfs_real_fdget(file, &lowerfd);
+	if (ret)
+		goto out_unlock;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	file_start_write(lowerfd.file);
+	ret = vfs_iter_write(lowerfd.file, iter, &iocb->ki_pos,
+			     shiftfs_iocb_to_rwf(iocb));
+	file_end_write(lowerfd.file);
+	revert_creds(oldcred);
+
+	/* Update size */
+	shiftfs_copyattr(inode->i_private, inode);
+
+	fdput(lowerfd);
+
+out_unlock:
+	inode_unlock(inode);
+	return ret;
+}
+
+static int shiftfs_fsync(struct file *file, loff_t start, loff_t end,
+			 int datasync)
+{
+	struct fd lowerfd;
+	const struct cred *oldcred;
+	int ret;
+
+	ret = shiftfs_real_fdget(file, &lowerfd);
+	if (ret)
+		return ret;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	ret = vfs_fsync_range(lowerfd.file, start, end, datasync);
+	revert_creds(oldcred);
+
+	fdput(lowerfd);
+	return ret;
+}
+
+static int shiftfs_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	struct file *realfile = file->private_data;
+	const struct cred *oldcred;
+	int ret;
+
+	if (!realfile->f_op->mmap)
+		return -ENODEV;
+
+	if (WARN_ON(file != vma->vm_file))
+		return -EIO;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	vma->vm_file = get_file(realfile);
+	ret = call_mmap(vma->vm_file, vma);
+	revert_creds(oldcred);
+
+	shiftfs_file_accessed(file);
+
+	if (ret) {
+		/*
+		 * Drop refcount from new vm_file value and restore original
+		 * vm_file value
+		 */
+		vma->vm_file = file;
+		fput(realfile);
+	} else {
+		/* Drop refcount from previous vm_file value */
+		fput(file);
+	}
+
+	return ret;
+}
+
+static long shiftfs_fallocate(struct file *file, int mode, loff_t offset,
+			      loff_t len)
+{
+	struct inode *inode = file_inode(file);
+	struct inode *loweri = inode->i_private;
+	struct fd lowerfd;
+	const struct cred *oldcred;
+	int ret;
+
+	ret = shiftfs_real_fdget(file, &lowerfd);
+	if (ret)
+		return ret;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	ret = vfs_fallocate(lowerfd.file, mode, offset, len);
+	revert_creds(oldcred);
+
+	/* Update size */
+	shiftfs_copyattr(loweri, inode);
+
+	fdput(lowerfd);
+	return ret;
+}
+
+static int shiftfs_fadvise(struct file *file, loff_t offset, loff_t len,
+			   int advice)
+{
+	struct fd lowerfd;
+	const struct cred *oldcred;
+	int ret;
+
+	ret = shiftfs_real_fdget(file, &lowerfd);
+	if (ret)
+		return ret;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	ret = vfs_fadvise(lowerfd.file, offset, len, advice);
+	revert_creds(oldcred);
+
+	fdput(lowerfd);
+	return ret;
+}
+
+static int shiftfs_override_ioctl_creds(int cmd, const struct super_block *sb,
+					const struct cred **oldcred,
+					struct cred **newcred)
+{
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+	kuid_t fsuid = current_fsuid();
+	kgid_t fsgid = current_fsgid();
+
+	*oldcred = shiftfs_override_creds(sb);
+
+	*newcred = prepare_creds();
+	if (!*newcred) {
+		revert_creds(*oldcred);
+		return -ENOMEM;
+	}
+
+	(*newcred)->fsuid = shift_kuid(sb->s_user_ns, sbinfo->userns, fsuid);
+	(*newcred)->fsgid = shift_kgid(sb->s_user_ns, sbinfo->userns, fsgid);
+
+	/* clear all caps to prevent bypassing capable() checks */
+	cap_clear((*newcred)->cap_bset);
+	cap_clear((*newcred)->cap_effective);
+	cap_clear((*newcred)->cap_inheritable);
+	cap_clear((*newcred)->cap_permitted);
+
+	if (cmd == BTRFS_IOC_SNAP_DESTROY) {
+		kuid_t kuid_root = make_kuid(sb->s_user_ns, 0);
+		/*
+		 * Allow the root user in the container to remove subvolumes
+		 * from other users.
+		 */
+		if (uid_valid(kuid_root) && uid_eq(fsuid, kuid_root))
+			cap_raise((*newcred)->cap_effective, CAP_DAC_OVERRIDE);
+	}
+
+	put_cred(override_creds(*newcred));
+	return 0;
+}
+
+static inline void shiftfs_revert_ioctl_creds(const struct cred *oldcred,
+					      struct cred *newcred)
+{
+	return shiftfs_revert_object_creds(oldcred, newcred);
+}
+
+static inline bool is_btrfs_snap_ioctl(int cmd)
+{
+	if ((cmd == BTRFS_IOC_SNAP_CREATE) || (cmd == BTRFS_IOC_SNAP_CREATE_V2))
+		return true;
+
+	return false;
+}
+
+static int shiftfs_btrfs_ioctl_fd_restore(int cmd, int fd, void __user *arg,
+					  struct btrfs_ioctl_vol_args *v1,
+					  struct btrfs_ioctl_vol_args_v2 *v2)
+{
+	int ret;
+
+	if (!is_btrfs_snap_ioctl(cmd))
+		return 0;
+
+	if (cmd == BTRFS_IOC_SNAP_CREATE)
+		ret = copy_to_user(arg, v1, sizeof(*v1));
+	else
+		ret = copy_to_user(arg, v2, sizeof(*v2));
+
+	close_fd(fd);
+	kfree(v1);
+	kfree(v2);
+
+	return ret ? -EFAULT: 0;
+}
+
+static int shiftfs_btrfs_ioctl_fd_replace(int cmd, void __user *arg,
+					  struct btrfs_ioctl_vol_args **b1,
+					  struct btrfs_ioctl_vol_args_v2 **b2,
+					  int *newfd)
+{
+	int oldfd, ret;
+	struct fd src;
+	struct fd lfd = {};
+	struct btrfs_ioctl_vol_args *v1 = NULL;
+	struct btrfs_ioctl_vol_args_v2 *v2 = NULL;
+
+	*b1 = NULL;
+	*b2 = NULL;
+
+	if (!is_btrfs_snap_ioctl(cmd))
+		return 0;
+
+	if (cmd == BTRFS_IOC_SNAP_CREATE) {
+		v1 = memdup_user(arg, sizeof(*v1));
+		if (IS_ERR(v1))
+			return PTR_ERR(v1);
+		oldfd = v1->fd;
+	} else {
+		v2 = memdup_user(arg, sizeof(*v2));
+		if (IS_ERR(v2))
+			return PTR_ERR(v2);
+		oldfd = v2->fd;
+	}
+
+	src = fdget(oldfd);
+	if (!src.file) {
+		ret = -EINVAL;
+		goto err_free;
+	}
+
+	ret = shiftfs_real_fdget(src.file, &lfd);
+	if (ret) {
+		fdput(src);
+		goto err_free;
+	}
+
+	/*
+	 * shiftfs_real_fdget() does not take a reference to lfd.file, so
+	 * take a reference here to offset the one which will be put by
+	 * close_fd(), and make sure that reference is put on fdput(lfd).
+	 */
+	get_file(lfd.file);
+	lfd.flags |= FDPUT_FPUT;
+	fdput(src);
+
+	*newfd = get_unused_fd_flags(lfd.file->f_flags);
+	if (*newfd < 0) {
+		fdput(lfd);
+		ret = *newfd;
+		goto err_free;
+	}
+
+	fd_install(*newfd, lfd.file);
+
+	if (cmd == BTRFS_IOC_SNAP_CREATE) {
+		v1->fd = *newfd;
+		ret = copy_to_user(arg, v1, sizeof(*v1));
+		v1->fd = oldfd;
+	} else {
+		v2->fd = *newfd;
+		ret = copy_to_user(arg, v2, sizeof(*v2));
+		v2->fd = oldfd;
+	}
+
+	if (!ret) {
+		*b1 = v1;
+		*b2 = v2;
+	} else {
+		shiftfs_btrfs_ioctl_fd_restore(cmd, *newfd, arg, v1, v2);
+		ret = -EFAULT;
+	}
+
+	return ret;
+
+err_free:
+	kfree(v1);
+	kfree(v2);
+
+	return ret;
+}
+
+static long shiftfs_real_ioctl(struct file *file, unsigned int cmd,
+			       unsigned long arg)
+{
+	struct fd lowerfd;
+	struct cred *newcred;
+	const struct cred *oldcred;
+	int newfd = -EBADF;
+	long err = 0, ret = 0;
+	void __user *argp = (void __user *)arg;
+	struct super_block *sb = file->f_path.dentry->d_sb;
+	struct btrfs_ioctl_vol_args *btrfs_v1 = NULL;
+	struct btrfs_ioctl_vol_args_v2 *btrfs_v2 = NULL;
+
+	ret = shiftfs_btrfs_ioctl_fd_replace(cmd, argp, &btrfs_v1, &btrfs_v2,
+					     &newfd);
+	if (ret < 0)
+		return ret;
+
+	ret = shiftfs_real_fdget(file, &lowerfd);
+	if (ret)
+		goto out_restore;
+
+	ret = shiftfs_override_ioctl_creds(cmd, sb, &oldcred, &newcred);
+	if (ret)
+		goto out_fdput;
+
+	ret = vfs_ioctl(lowerfd.file, cmd, arg);
+
+	shiftfs_revert_ioctl_creds(oldcred, newcred);
+
+	shiftfs_copyattr(file_inode(lowerfd.file), file_inode(file));
+	shiftfs_copyflags(file_inode(lowerfd.file), file_inode(file));
+
+out_fdput:
+	fdput(lowerfd);
+
+out_restore:
+	err = shiftfs_btrfs_ioctl_fd_restore(cmd, newfd, argp,
+					     btrfs_v1, btrfs_v2);
+	if (!ret)
+		ret = err;
+
+	return ret;
+}
+
+static bool in_ioctl_whitelist(int flag, unsigned long arg)
+{
+	void __user *argp = (void __user *)arg;
+	u64 flags = 0;
+
+	switch (flag) {
+	case BTRFS_IOC_FS_INFO:
+		return true;
+	case BTRFS_IOC_SNAP_CREATE:
+		return true;
+	case BTRFS_IOC_SNAP_CREATE_V2:
+		return true;
+	case BTRFS_IOC_SUBVOL_CREATE:
+		return true;
+	case BTRFS_IOC_SUBVOL_CREATE_V2:
+		return true;
+	case BTRFS_IOC_SUBVOL_GETFLAGS:
+		return true;
+	case BTRFS_IOC_SUBVOL_SETFLAGS:
+		if (copy_from_user(&flags, argp, sizeof(flags)))
+			return false;
+
+		if (flags & ~BTRFS_SUBVOL_RDONLY)
+			return false;
+
+		return true;
+	case BTRFS_IOC_SNAP_DESTROY:
+		return true;
+	}
+
+	return false;
+}
+
+static long shiftfs_ioctl(struct file *file, unsigned int cmd,
+			  unsigned long arg)
+{
+	switch (cmd) {
+	case FS_IOC_GETVERSION:
+		/* fall through */
+	case FS_IOC_GETFLAGS:
+		/* fall through */
+	case FS_IOC_SETFLAGS:
+		break;
+	default:
+		if (!in_ioctl_whitelist(cmd, arg) ||
+		    !shiftfs_passthrough_ioctls(file->f_path.dentry->d_sb->s_fs_info))
+			return -ENOTTY;
+	}
+
+	return shiftfs_real_ioctl(file, cmd, arg);
+}
+
+static long shiftfs_compat_ioctl(struct file *file, unsigned int cmd,
+				 unsigned long arg)
+{
+	switch (cmd) {
+	case FS_IOC32_GETVERSION:
+		/* fall through */
+	case FS_IOC32_GETFLAGS:
+		/* fall through */
+	case FS_IOC32_SETFLAGS:
+		break;
+	default:
+		if (!in_ioctl_whitelist(cmd, arg) ||
+		    !shiftfs_passthrough_ioctls(file->f_path.dentry->d_sb->s_fs_info))
+			return -ENOIOCTLCMD;
+	}
+
+	return shiftfs_real_ioctl(file, cmd, arg);
+}
+
+enum shiftfs_copyop {
+	SHIFTFS_COPY,
+	SHIFTFS_CLONE,
+	SHIFTFS_DEDUPE,
+};
+
+static ssize_t shiftfs_copyfile(struct file *file_in, loff_t pos_in,
+				struct file *file_out, loff_t pos_out, u64 len,
+				unsigned int flags, enum shiftfs_copyop op)
+{
+	ssize_t ret;
+	struct fd real_in, real_out;
+	const struct cred *oldcred;
+	struct inode *inode_out = file_inode(file_out);
+	struct inode *loweri = inode_out->i_private;
+
+	ret = shiftfs_real_fdget(file_out, &real_out);
+	if (ret)
+		return ret;
+
+	ret = shiftfs_real_fdget(file_in, &real_in);
+	if (ret) {
+		fdput(real_out);
+		return ret;
+	}
+
+	oldcred = shiftfs_override_creds(inode_out->i_sb);
+	switch (op) {
+	case SHIFTFS_COPY:
+		ret = vfs_copy_file_range(real_in.file, pos_in, real_out.file,
+					  pos_out, len, flags);
+		break;
+
+	case SHIFTFS_CLONE:
+		ret = vfs_clone_file_range(real_in.file, pos_in, real_out.file,
+					   pos_out, len, flags);
+		break;
+
+	case SHIFTFS_DEDUPE:
+		ret = vfs_dedupe_file_range_one(real_in.file, pos_in,
+						real_out.file, pos_out, len,
+						flags);
+		break;
+	}
+	revert_creds(oldcred);
+
+	/* Update size */
+	shiftfs_copyattr(loweri, inode_out);
+
+	fdput(real_in);
+	fdput(real_out);
+
+	return ret;
+}
+
+static ssize_t shiftfs_copy_file_range(struct file *file_in, loff_t pos_in,
+				       struct file *file_out, loff_t pos_out,
+				       size_t len, unsigned int flags)
+{
+	return shiftfs_copyfile(file_in, pos_in, file_out, pos_out, len, flags,
+				SHIFTFS_COPY);
+}
+
+static loff_t shiftfs_remap_file_range(struct file *file_in, loff_t pos_in,
+				       struct file *file_out, loff_t pos_out,
+				       loff_t len, unsigned int remap_flags)
+{
+	enum shiftfs_copyop op;
+
+	if (remap_flags & ~(REMAP_FILE_DEDUP | REMAP_FILE_ADVISORY))
+		return -EINVAL;
+
+	if (remap_flags & REMAP_FILE_DEDUP)
+		op = SHIFTFS_DEDUPE;
+	else
+		op = SHIFTFS_CLONE;
+
+	return shiftfs_copyfile(file_in, pos_in, file_out, pos_out, len,
+				remap_flags, op);
+}
+
+static int shiftfs_iterate_shared(struct file *file, struct dir_context *ctx)
+{
+	const struct cred *oldcred;
+	int err = -ENOTDIR;
+	struct file *realfile = file->private_data;
+
+	oldcred = shiftfs_override_creds(file->f_path.dentry->d_sb);
+	err = iterate_dir(realfile, ctx);
+	revert_creds(oldcred);
+
+	return err;
+}
+
+const struct file_operations shiftfs_file_operations = {
+	.open			= shiftfs_open,
+	.release		= shiftfs_release,
+	.llseek			= shiftfs_file_llseek,
+	.read_iter		= shiftfs_read_iter,
+	.write_iter		= shiftfs_write_iter,
+	.fsync			= shiftfs_fsync,
+	.mmap			= shiftfs_mmap,
+	.fallocate		= shiftfs_fallocate,
+	.fadvise		= shiftfs_fadvise,
+	.unlocked_ioctl		= shiftfs_ioctl,
+	.compat_ioctl		= shiftfs_compat_ioctl,
+	.copy_file_range	= shiftfs_copy_file_range,
+	.remap_file_range	= shiftfs_remap_file_range,
+	.splice_read		= generic_file_splice_read,
+	.splice_write		= iter_file_splice_write,
+};
+
+const struct file_operations shiftfs_dir_operations = {
+	.open			= shiftfs_dir_open,
+	.release		= shiftfs_dir_release,
+	.compat_ioctl		= shiftfs_compat_ioctl,
+	.fsync			= shiftfs_fsync,
+	.iterate_shared		= shiftfs_iterate_shared,
+	.llseek			= shiftfs_dir_llseek,
+	.read			= generic_read_dir,
+	.unlocked_ioctl		= shiftfs_ioctl,
+};
+
+static const struct address_space_operations shiftfs_aops = {
+	/* For O_DIRECT dentry_open() checks f_mapping->a_ops->direct_IO */
+	.direct_IO	= noop_direct_IO,
+};
+
+static void shiftfs_fill_inode(struct inode *inode, unsigned long ino,
+			       umode_t mode, dev_t dev, struct dentry *dentry)
+{
+	struct inode *loweri;
+
+	inode->i_ino = ino;
+	inode->i_flags |= S_NOCMTIME;
+
+	mode &= S_IFMT;
+	inode->i_mode = mode;
+	switch (mode & S_IFMT) {
+	case S_IFDIR:
+		inode->i_op = &shiftfs_dir_inode_operations;
+		inode->i_fop = &shiftfs_dir_operations;
+		break;
+	case S_IFLNK:
+		inode->i_op = &shiftfs_symlink_inode_operations;
+		break;
+	case S_IFREG:
+		inode->i_op = &shiftfs_file_inode_operations;
+		inode->i_fop = &shiftfs_file_operations;
+		inode->i_mapping->a_ops = &shiftfs_aops;
+		break;
+	default:
+		inode->i_op = &shiftfs_special_inode_operations;
+		init_special_inode(inode, mode, dev);
+		break;
+	}
+
+	if (!dentry)
+		return;
+
+	loweri = dentry->d_inode;
+	if (!loweri->i_op->get_link)
+		inode->i_opflags |= IOP_NOFOLLOW;
+
+	shiftfs_copyattr(loweri, inode);
+	shiftfs_copyflags(loweri, inode);
+	set_nlink(inode, loweri->i_nlink);
+}
+
+static int shiftfs_show_options(struct seq_file *m, struct dentry *dentry)
+{
+	struct super_block *sb = dentry->d_sb;
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+
+	if (sbinfo->mark)
+		seq_show_option(m, "mark", NULL);
+
+	if (sbinfo->passthrough)
+		seq_printf(m, ",passthrough=%u", sbinfo->passthrough);
+
+	return 0;
+}
+
+static int shiftfs_statfs(struct dentry *dentry, struct kstatfs *buf)
+{
+	struct super_block *sb = dentry->d_sb;
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+	struct dentry *root = sb->s_root;
+	struct dentry *realroot = root->d_fsdata;
+	struct path realpath = { .mnt = sbinfo->mnt, .dentry = realroot };
+	int err;
+
+	err = vfs_statfs(&realpath, buf);
+	if (err)
+		return err;
+
+	if (!shiftfs_passthrough_statfs(sbinfo))
+		buf->f_type = sb->s_magic;
+
+	return 0;
+}
+
+static void shiftfs_evict_inode(struct inode *inode)
+{
+	struct inode *loweri = inode->i_private;
+
+	clear_inode(inode);
+
+	if (loweri)
+		iput(loweri);
+}
+
+static void shiftfs_put_super(struct super_block *sb)
+{
+	struct shiftfs_super_info *sbinfo = sb->s_fs_info;
+
+	if (sbinfo) {
+		mntput(sbinfo->mnt);
+		put_cred(sbinfo->creator_cred);
+		kfree(sbinfo);
+	}
+}
+
+static const struct xattr_handler shiftfs_xattr_handler = {
+	.prefix = "",
+	.get    = shiftfs_xattr_get,
+	.set    = shiftfs_xattr_set,
+};
+
+const struct xattr_handler *shiftfs_xattr_handlers[] = {
+#ifdef CONFIG_SHIFT_FS_POSIX_ACL
+	&shiftfs_posix_acl_access_xattr_handler,
+	&shiftfs_posix_acl_default_xattr_handler,
+#endif
+	&shiftfs_xattr_handler,
+	NULL
+};
+
+static inline bool passthrough_is_subset(int old_flags, int new_flags)
+{
+	if ((new_flags & old_flags) != new_flags)
+		return false;
+
+	return true;
+}
+
+static int shiftfs_super_check_flags(unsigned long old_flags,
+				     unsigned long new_flags)
+{
+	if ((old_flags & SB_RDONLY) && !(new_flags & SB_RDONLY))
+		return -EPERM;
+
+	if ((old_flags & SB_NOSUID) && !(new_flags & SB_NOSUID))
+		return -EPERM;
+
+	if ((old_flags & SB_NODEV) && !(new_flags & SB_NODEV))
+		return -EPERM;
+
+	if ((old_flags & SB_NOEXEC) && !(new_flags & SB_NOEXEC))
+		return -EPERM;
+
+	if ((old_flags & SB_NOATIME) && !(new_flags & SB_NOATIME))
+		return -EPERM;
+
+	if ((old_flags & SB_NODIRATIME) && !(new_flags & SB_NODIRATIME))
+		return -EPERM;
+
+	if (!(old_flags & SB_POSIXACL) && (new_flags & SB_POSIXACL))
+		return -EPERM;
+
+	return 0;
+}
+
+static int shiftfs_remount(struct super_block *sb, int *flags, char *data)
+{
+	int err;
+	struct shiftfs_super_info new = {};
+	struct shiftfs_super_info *info = sb->s_fs_info;
+
+	err = shiftfs_parse_mount_options(&new, data);
+	if (err)
+		return err;
+
+	err = shiftfs_super_check_flags(sb->s_flags, *flags);
+	if (err)
+		return err;
+
+	/* Mark mount option cannot be changed. */
+	if (info->mark || (info->mark != new.mark))
+		return -EPERM;
+
+	if (info->passthrough != new.passthrough) {
+		/* Don't allow exceeding passthrough options of mark mount. */
+		if (!passthrough_is_subset(info->passthrough_mark,
+					   info->passthrough))
+			return -EPERM;
+
+		info->passthrough = new.passthrough;
+	}
+
+	return 0;
+}
+
+static const struct super_operations shiftfs_super_ops = {
+	.put_super	= shiftfs_put_super,
+	.show_options	= shiftfs_show_options,
+	.statfs		= shiftfs_statfs,
+	.remount_fs	= shiftfs_remount,
+	.evict_inode	= shiftfs_evict_inode,
+};
+
+struct shiftfs_data {
+	void *data;
+	const char *path;
+};
+
+static void shiftfs_super_force_flags(struct super_block *sb,
+				      unsigned long lower_flags)
+{
+	sb->s_flags |= lower_flags & (SB_RDONLY | SB_NOSUID | SB_NODEV |
+				      SB_NOEXEC | SB_NOATIME | SB_NODIRATIME);
+
+	if (!(lower_flags & SB_POSIXACL))
+		sb->s_flags &= ~SB_POSIXACL;
+}
+
+static int shiftfs_fill_super(struct super_block *sb, void *raw_data,
+			      int silent)
+{
+	int err;
+	struct path path = {};
+	struct shiftfs_super_info *sbinfo_mp;
+	char *name = NULL;
+	struct inode *inode = NULL;
+	struct dentry *dentry = NULL;
+	struct shiftfs_data *data = raw_data;
+	struct shiftfs_super_info *sbinfo = NULL;
+
+	if (!data->path)
+		return -EINVAL;
+
+	sb->s_fs_info = kzalloc(sizeof(*sbinfo), GFP_KERNEL);
+	if (!sb->s_fs_info)
+		return -ENOMEM;
+	sbinfo = sb->s_fs_info;
+
+	err = shiftfs_parse_mount_options(sbinfo, data->data);
+	if (err)
+		return err;
+
+	/* to mount a mark, must be userns admin */
+	if (!sbinfo->mark && !ns_capable(current_user_ns(), CAP_SYS_ADMIN))
+		return -EPERM;
+
+	name = kstrdup(data->path, GFP_KERNEL);
+	if (!name)
+		return -ENOMEM;
+
+	err = kern_path(name, LOOKUP_FOLLOW, &path);
+	if (err)
+		goto out_free_name;
+
+	if (!S_ISDIR(path.dentry->d_inode->i_mode)) {
+		err = -ENOTDIR;
+		goto out_put_path;
+	}
+
+	/*
+	 * It makes no sense to handle idmapped layers from shiftfs.
+	 * And we didn't support it properly anyway.
+	 */
+	if (is_idmapped_mnt(path.mnt)) {
+		err = -EINVAL;
+		pr_err("idmapped layers are currently not supported\n");
+		goto out_put_path;
+	}
+
+	sb->s_flags |= SB_POSIXACL;
+
+	if (sbinfo->mark) {
+		struct cred *cred_tmp;
+		struct super_block *lower_sb = path.mnt->mnt_sb;
+
+		/* to mark a mount point, must root wrt lower s_user_ns */
+		if (!ns_capable(lower_sb->s_user_ns, CAP_SYS_ADMIN)) {
+			err = -EPERM;
+			goto out_put_path;
+		}
+
+		/*
+		 * this part is visible unshifted, so make sure no
+		 * executables that could be used to give suid
+		 * privileges
+		 */
+		sb->s_iflags = SB_I_NOEXEC;
+
+		shiftfs_super_force_flags(sb, lower_sb->s_flags);
+
+		/*
+		 * Handle nesting of shiftfs mounts by referring this mark
+		 * mount back to the original mark mount. This is more
+		 * efficient and alleviates concerns about stack depth.
+		 */
+		if (lower_sb->s_magic == SHIFTFS_MAGIC) {
+			sbinfo_mp = lower_sb->s_fs_info;
+
+			/* Doesn't make sense to mark a mark mount */
+			if (sbinfo_mp->mark) {
+				err = -EINVAL;
+				goto out_put_path;
+			}
+
+			if (!passthrough_is_subset(sbinfo_mp->passthrough,
+						   sbinfo->passthrough)) {
+				err = -EPERM;
+				goto out_put_path;
+			}
+
+			sbinfo->mnt = mntget(sbinfo_mp->mnt);
+			dentry = dget(path.dentry->d_fsdata);
+			/*
+			 * Copy up the passthrough mount options from the
+			 * parent mark mountpoint.
+			 */
+			sbinfo->passthrough_mark = sbinfo_mp->passthrough_mark;
+			sbinfo->creator_cred = get_cred(sbinfo_mp->creator_cred);
+		} else {
+			sbinfo->mnt = mntget(path.mnt);
+			dentry = dget(path.dentry);
+			/*
+			 * For a new mark passthrough_mark and passthrough
+			 * are identical.
+			 */
+			sbinfo->passthrough_mark = sbinfo->passthrough;
+
+			cred_tmp = prepare_creds();
+			if (!cred_tmp) {
+				err = -ENOMEM;
+				goto out_put_path;
+			}
+			/* Don't override disk quota limits or use reserved space. */
+			cap_lower(cred_tmp->cap_effective, CAP_SYS_RESOURCE);
+			sbinfo->creator_cred = cred_tmp;
+		}
+	} else {
+		/*
+		 * This leg executes if we're admin capable in the namespace,
+		 * so be very careful.
+		 */
+		err = -EPERM;
+		if (path.dentry->d_sb->s_magic != SHIFTFS_MAGIC)
+			goto out_put_path;
+
+		sbinfo_mp = path.dentry->d_sb->s_fs_info;
+		if (!sbinfo_mp->mark)
+			goto out_put_path;
+
+		if (!passthrough_is_subset(sbinfo_mp->passthrough,
+					   sbinfo->passthrough))
+			goto out_put_path;
+
+		sbinfo->mnt = mntget(sbinfo_mp->mnt);
+		sbinfo->creator_cred = get_cred(sbinfo_mp->creator_cred);
+		dentry = dget(path.dentry->d_fsdata);
+		/*
+		 * Copy up passthrough settings from mark mountpoint so we can
+		 * verify when the overlay wants to remount with different
+		 * passthrough settings.
+		 */
+		sbinfo->passthrough_mark = sbinfo_mp->passthrough;
+		shiftfs_super_force_flags(sb, path.mnt->mnt_sb->s_flags);
+	}
+
+	sb->s_stack_depth = dentry->d_sb->s_stack_depth + 1;
+	if (sb->s_stack_depth > FILESYSTEM_MAX_STACK_DEPTH) {
+		printk(KERN_ERR "shiftfs: maximum stacking depth exceeded\n");
+		err = -EINVAL;
+		goto out_put_path;
+	}
+
+	inode = new_inode(sb);
+	if (!inode) {
+		err = -ENOMEM;
+		goto out_put_path;
+	}
+	shiftfs_fill_inode(inode, dentry->d_inode->i_ino, S_IFDIR, 0, dentry);
+
+	ihold(dentry->d_inode);
+	inode->i_private = dentry->d_inode;
+
+	sb->s_magic = SHIFTFS_MAGIC;
+	sb->s_maxbytes = MAX_LFS_FILESIZE;
+	sb->s_op = &shiftfs_super_ops;
+	sb->s_xattr = shiftfs_xattr_handlers;
+	sb->s_d_op = &shiftfs_dentry_ops;
+	sb->s_root = d_make_root(inode);
+	if (!sb->s_root) {
+		err = -ENOMEM;
+		goto out_put_path;
+	}
+
+	sb->s_root->d_fsdata = dentry;
+	sbinfo->userns = get_user_ns(dentry->d_sb->s_user_ns);
+	shiftfs_copyattr(dentry->d_inode, sb->s_root->d_inode);
+
+	dentry = NULL;
+	err = 0;
+
+out_put_path:
+	path_put(&path);
+
+out_free_name:
+	kfree(name);
+
+	dput(dentry);
+
+	return err;
+}
+
+static struct dentry *shiftfs_mount(struct file_system_type *fs_type,
+				    int flags, const char *dev_name, void *data)
+{
+	struct shiftfs_data d = { data, dev_name };
+
+	return mount_nodev(fs_type, flags, &d, shiftfs_fill_super);
+}
+
+static struct file_system_type shiftfs_type = {
+	.owner		= THIS_MODULE,
+	.name		= "shiftfs",
+	.mount		= shiftfs_mount,
+	.kill_sb	= kill_anon_super,
+	.fs_flags	= FS_USERNS_MOUNT,
+};
+
+static int __init shiftfs_init(void)
+{
+	return register_filesystem(&shiftfs_type);
+}
+
+static void __exit shiftfs_exit(void)
+{
+	unregister_filesystem(&shiftfs_type);
+}
+
+MODULE_ALIAS_FS("shiftfs");
+MODULE_AUTHOR("James Bottomley");
+MODULE_AUTHOR("Seth Forshee <seth.forshee@canonical.com>");
+MODULE_AUTHOR("Christian Brauner <christian.brauner@ubuntu.com>");
+MODULE_DESCRIPTION("id shifting filesystem");
+MODULE_LICENSE("GPL v2");
+module_init(shiftfs_init)
+module_exit(shiftfs_exit)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/signalfd.c
+++ linux-xilinx-zynqmp-5.15.0/fs/signalfd.c
@@ -35,17 +35,7 @@
 
 void signalfd_cleanup(struct sighand_struct *sighand)
 {
-	wait_queue_head_t *wqh = &sighand->signalfd_wqh;
-	/*
-	 * The lockless check can race with remove_wait_queue() in progress,
-	 * but in this case its caller should run under rcu_read_lock() and
-	 * sighand_cachep is SLAB_TYPESAFE_BY_RCU, we can safely return.
-	 */
-	if (likely(!waitqueue_active(wqh)))
-		return;
-
-	/* wait_queue_entry_t->func(POLLFREE) should do remove_wait_queue() */
-	wake_up_poll(wqh, EPOLLHUP | POLLFREE);
+	wake_up_pollfree(&sighand->signalfd_wqh);
 }
 
 struct signalfd_ctx {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/smbfs_common/cifs_arc4.c
+++ linux-xilinx-zynqmp-5.15.0/fs/smbfs_common/cifs_arc4.c
@@ -72,16 +72,3 @@
 	ctx->y = y;
 }
 EXPORT_SYMBOL_GPL(cifs_arc4_crypt);
-
-static int __init
-init_smbfs_common(void)
-{
-	return 0;
-}
-static void __init
-exit_smbfs_common(void)
-{
-}
-
-module_init(init_smbfs_common)
-module_exit(exit_smbfs_common)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/splice.c
+++ linux-xilinx-zynqmp-5.15.0/fs/splice.c
@@ -759,20 +759,21 @@
 /*
  * Attempt to initiate a splice from pipe to file.
  */
-static long do_splice_from(struct pipe_inode_info *pipe, struct file *out,
-			   loff_t *ppos, size_t len, unsigned int flags)
+long do_splice_from(struct pipe_inode_info *pipe, struct file *out,
+		    loff_t *ppos, size_t len, unsigned int flags)
 {
 	if (unlikely(!out->f_op->splice_write))
 		return warn_unsupported(out, "write");
 	return out->f_op->splice_write(pipe, out, ppos, len, flags);
 }
+EXPORT_SYMBOL_GPL(do_splice_from);
 
 /*
  * Attempt to initiate a splice from a file to a pipe.
  */
-static long do_splice_to(struct file *in, loff_t *ppos,
-			 struct pipe_inode_info *pipe, size_t len,
-			 unsigned int flags)
+long do_splice_to(struct file *in, loff_t *ppos,
+		  struct pipe_inode_info *pipe, size_t len,
+		  unsigned int flags)
 {
 	unsigned int p_space;
 	int ret;
@@ -795,6 +796,7 @@
 		return warn_unsupported(in, "read");
 	return in->f_op->splice_read(in, ppos, pipe, len, flags);
 }
+EXPORT_SYMBOL_GPL(do_splice_to);
 
 /**
  * splice_direct_to_actor - splices data directly between two non-pipes
--- linux-xilinx-zynqmp-5.15.0.orig/fs/squashfs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/squashfs/inode.c
@@ -48,6 +48,10 @@
 	gid_t i_gid;
 	int err;
 
+	inode->i_ino = le32_to_cpu(sqsh_ino->inode_number);
+	if (inode->i_ino == 0)
+		return -EINVAL;
+
 	err = squashfs_get_id(sb, le16_to_cpu(sqsh_ino->uid), &i_uid);
 	if (err)
 		return err;
@@ -58,7 +62,6 @@
 
 	i_uid_write(inode, i_uid);
 	i_gid_write(inode, i_gid);
-	inode->i_ino = le32_to_cpu(sqsh_ino->inode_number);
 	inode->i_mtime.tv_sec = le32_to_cpu(sqsh_ino->mtime);
 	inode->i_atime.tv_sec = inode->i_mtime.tv_sec;
 	inode->i_ctime.tv_sec = inode->i_mtime.tv_sec;
@@ -276,8 +279,13 @@
 		if (err < 0)
 			goto failed_read;
 
-		set_nlink(inode, le32_to_cpu(sqsh_ino->nlink));
 		inode->i_size = le32_to_cpu(sqsh_ino->symlink_size);
+		if (inode->i_size > PAGE_SIZE) {
+			ERROR("Corrupted symlink\n");
+			return -EINVAL;
+		}
+
+		set_nlink(inode, le32_to_cpu(sqsh_ino->nlink));
 		inode->i_op = &squashfs_symlink_inode_ops;
 		inode_nohighmem(inode);
 		inode->i_data.a_ops = &squashfs_symlink_aops;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/squashfs/squashfs_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/squashfs/squashfs_fs.h
@@ -183,7 +183,7 @@
 #define SQUASHFS_ID_BLOCK_BYTES(A)	(SQUASHFS_ID_BLOCKS(A) *\
 					sizeof(u64))
 /* xattr id lookup table defines */
-#define SQUASHFS_XATTR_BYTES(A)		((A) * sizeof(struct squashfs_xattr_id))
+#define SQUASHFS_XATTR_BYTES(A)		(((u64) (A)) * sizeof(struct squashfs_xattr_id))
 
 #define SQUASHFS_XATTR_BLOCK(A)		(SQUASHFS_XATTR_BYTES(A) / \
 					SQUASHFS_METADATA_SIZE)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/squashfs/squashfs_fs_sb.h
+++ linux-xilinx-zynqmp-5.15.0/fs/squashfs/squashfs_fs_sb.h
@@ -63,7 +63,7 @@
 	long long				bytes_used;
 	unsigned int				inodes;
 	unsigned int				fragments;
-	int					xattr_ids;
+	unsigned int				xattr_ids;
 	unsigned int				ids;
 	bool					panic_on_errors;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/fs/squashfs/xattr.h
+++ linux-xilinx-zynqmp-5.15.0/fs/squashfs/xattr.h
@@ -10,12 +10,12 @@
 
 #ifdef CONFIG_SQUASHFS_XATTR
 extern __le64 *squashfs_read_xattr_id_table(struct super_block *, u64,
-		u64 *, int *);
+		u64 *, unsigned int *);
 extern int squashfs_xattr_lookup(struct super_block *, unsigned int, int *,
 		unsigned int *, unsigned long long *);
 #else
 static inline __le64 *squashfs_read_xattr_id_table(struct super_block *sb,
-		u64 start, u64 *xattr_table_start, int *xattr_ids)
+		u64 start, u64 *xattr_table_start, unsigned int *xattr_ids)
 {
 	struct squashfs_xattr_id_table *id_table;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/squashfs/xattr_id.c
+++ linux-xilinx-zynqmp-5.15.0/fs/squashfs/xattr_id.c
@@ -56,7 +56,7 @@
  * Read uncompressed xattr id lookup table indexes from disk into memory
  */
 __le64 *squashfs_read_xattr_id_table(struct super_block *sb, u64 table_start,
-		u64 *xattr_table_start, int *xattr_ids)
+		u64 *xattr_table_start, unsigned int *xattr_ids)
 {
 	struct squashfs_sb_info *msblk = sb->s_fs_info;
 	unsigned int len, indexes;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/stat.c
+++ linux-xilinx-zynqmp-5.15.0/fs/stat.c
@@ -334,9 +334,6 @@
 #  define choose_32_64(a,b) b
 #endif
 
-#define valid_dev(x)  choose_32_64(old_valid_dev(x),true)
-#define encode_dev(x) choose_32_64(old_encode_dev,new_encode_dev)(x)
-
 #ifndef INIT_STRUCT_STAT_PADDING
 #  define INIT_STRUCT_STAT_PADDING(st) memset(&st, 0, sizeof(st))
 #endif
@@ -345,7 +342,9 @@
 {
 	struct stat tmp;
 
-	if (!valid_dev(stat->dev) || !valid_dev(stat->rdev))
+	if (sizeof(tmp.st_dev) < 4 && !old_valid_dev(stat->dev))
+		return -EOVERFLOW;
+	if (sizeof(tmp.st_rdev) < 4 && !old_valid_dev(stat->rdev))
 		return -EOVERFLOW;
 #if BITS_PER_LONG == 32
 	if (stat->size > MAX_NON_LFS)
@@ -353,7 +352,7 @@
 #endif
 
 	INIT_STRUCT_STAT_PADDING(tmp);
-	tmp.st_dev = encode_dev(stat->dev);
+	tmp.st_dev = new_encode_dev(stat->dev);
 	tmp.st_ino = stat->ino;
 	if (sizeof(tmp.st_ino) < sizeof(stat->ino) && tmp.st_ino != stat->ino)
 		return -EOVERFLOW;
@@ -363,7 +362,7 @@
 		return -EOVERFLOW;
 	SET_UID(tmp.st_uid, from_kuid_munged(current_user_ns(), stat->uid));
 	SET_GID(tmp.st_gid, from_kgid_munged(current_user_ns(), stat->gid));
-	tmp.st_rdev = encode_dev(stat->rdev);
+	tmp.st_rdev = new_encode_dev(stat->rdev);
 	tmp.st_size = stat->size;
 	tmp.st_atime = stat->atime.tv_sec;
 	tmp.st_mtime = stat->mtime.tv_sec;
@@ -644,11 +643,13 @@
 {
 	struct compat_stat tmp;
 
-	if (!old_valid_dev(stat->dev) || !old_valid_dev(stat->rdev))
+	if (sizeof(tmp.st_dev) < 4 && !old_valid_dev(stat->dev))
+		return -EOVERFLOW;
+	if (sizeof(tmp.st_rdev) < 4 && !old_valid_dev(stat->rdev))
 		return -EOVERFLOW;
 
 	memset(&tmp, 0, sizeof(tmp));
-	tmp.st_dev = old_encode_dev(stat->dev);
+	tmp.st_dev = new_encode_dev(stat->dev);
 	tmp.st_ino = stat->ino;
 	if (sizeof(tmp.st_ino) < sizeof(stat->ino) && tmp.st_ino != stat->ino)
 		return -EOVERFLOW;
@@ -658,7 +659,7 @@
 		return -EOVERFLOW;
 	SET_UID(tmp.st_uid, from_kuid_munged(current_user_ns(), stat->uid));
 	SET_GID(tmp.st_gid, from_kgid_munged(current_user_ns(), stat->gid));
-	tmp.st_rdev = old_encode_dev(stat->rdev);
+	tmp.st_rdev = new_encode_dev(stat->rdev);
 	if ((u64) stat->size > MAX_NON_LFS)
 		return -EOVERFLOW;
 	tmp.st_size = stat->size;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/statfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/statfs.c
@@ -130,6 +130,7 @@
 	if (sizeof(buf) == sizeof(*st))
 		memcpy(&buf, st, sizeof(*st));
 	else {
+		memset(&buf, 0, sizeof(buf));
 		if (sizeof buf.f_blocks == 4) {
 			if ((st->f_blocks | st->f_bfree | st->f_bavail |
 			     st->f_bsize | st->f_frsize) &
@@ -158,7 +159,6 @@
 		buf.f_namelen = st->f_namelen;
 		buf.f_frsize = st->f_frsize;
 		buf.f_flags = st->f_flags;
-		memset(buf.f_spare, 0, sizeof(buf.f_spare));
 	}
 	if (copy_to_user(p, &buf, sizeof(buf)))
 		return -EFAULT;
@@ -171,6 +171,7 @@
 	if (sizeof(buf) == sizeof(*st))
 		memcpy(&buf, st, sizeof(*st));
 	else {
+		memset(&buf, 0, sizeof(buf));
 		buf.f_type = st->f_type;
 		buf.f_bsize = st->f_bsize;
 		buf.f_blocks = st->f_blocks;
@@ -182,7 +183,6 @@
 		buf.f_namelen = st->f_namelen;
 		buf.f_frsize = st->f_frsize;
 		buf.f_flags = st->f_flags;
-		memset(buf.f_spare, 0, sizeof(buf.f_spare));
 	}
 	if (copy_to_user(p, &buf, sizeof(buf)))
 		return -EFAULT;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/super.c
@@ -293,7 +293,7 @@
 		WARN_ON(s->s_inode_lru.node);
 		WARN_ON(!list_empty(&s->s_mounts));
 		security_sb_free(s);
-		fscrypt_sb_free(s);
+		fscrypt_destroy_keyring(s);
 		put_user_ns(s->s_user_ns);
 		kfree(s->s_subtype);
 		call_rcu(&s->rcu, destroy_super_rcu);
@@ -450,12 +450,22 @@
 
 		cgroup_writeback_umount();
 
-		/* evict all inodes with zero refcount */
+		/* Evict all inodes with zero refcount. */
 		evict_inodes(sb);
-		/* only nonzero refcount inodes can have marks */
+
+		/*
+		 * Clean up and evict any inodes that still have references due
+		 * to fsnotify or the security policy.
+		 */
 		fsnotify_sb_delete(sb);
 		security_sb_delete(sb);
 
+		/*
+		 * Now that all potentially-encrypted inodes have been evicted,
+		 * the fscrypt keyring can be destroyed.
+		 */
+		fscrypt_destroy_keyring(sb);
+
 		if (sb->s_dio_done_wq) {
 			destroy_workqueue(sb->s_dio_done_wq);
 			sb->s_dio_done_wq = NULL;
@@ -476,6 +486,8 @@
 	spin_unlock(&sb_lock);
 	up_write(&sb->s_umount);
 	if (sb->s_bdi != &noop_backing_dev_info) {
+		if (sb->s_iflags & SB_I_PERSB_BDI)
+			bdi_unregister(sb->s_bdi);
 		bdi_put(sb->s_bdi);
 		sb->s_bdi = &noop_backing_dev_info;
 	}
@@ -518,6 +530,17 @@
 	struct user_namespace *user_ns = fc->global ? &init_user_ns : fc->user_ns;
 	int err;
 
+	/*
+	 * Never allow s_user_ns != &init_user_ns when FS_USERNS_MOUNT is
+	 * not set, as the filesystem is likely unprepared to handle it.
+	 * This can happen when fsconfig() is called from init_user_ns with
+	 * an fs_fd opened in another user namespace.
+	 */
+	if (user_ns != &init_user_ns && !(fc->fs_type->fs_flags & FS_USERNS_MOUNT)) {
+		errorfc(fc, "VFS: Mounting from non-initial user namespace is not allowed");
+		return ERR_PTR(-EPERM);
+	}
+
 retry:
 	spin_lock(&sb_lock);
 	if (test) {
@@ -853,6 +876,7 @@
 	struct super_block *sb = fc->root->d_sb;
 	int retval;
 	bool remount_ro = false;
+	bool remount_rw = false;
 	bool force = fc->sb_flags & SB_FORCE;
 
 	if (fc->sb_flags_mask & ~MS_RMT_MASK)
@@ -870,7 +894,7 @@
 		    bdev_read_only(sb->s_bdev))
 			return -EACCES;
 #endif
-
+		remount_rw = !(fc->sb_flags & SB_RDONLY) && sb_rdonly(sb);
 		remount_ro = (fc->sb_flags & SB_RDONLY) && !sb_rdonly(sb);
 	}
 
@@ -900,6 +924,14 @@
 			if (retval)
 				return retval;
 		}
+	} else if (remount_rw) {
+		/*
+		 * We set s_readonly_remount here to protect filesystem's
+		 * reconfigure code from writes from userspace until
+		 * reconfigure finishes.
+		 */
+		sb->s_readonly_remount = 1;
+		smp_wmb();
 	}
 
 	if (fc->ops->reconfigure) {
@@ -1421,8 +1453,8 @@
 }
 EXPORT_SYMBOL(mount_nodev);
 
-static int reconfigure_single(struct super_block *s,
-			      int flags, void *data)
+int reconfigure_single(struct super_block *s,
+		       int flags, void *data)
 {
 	struct fs_context *fc;
 	int ret;
@@ -1562,6 +1594,7 @@
 	}
 	WARN_ON(sb->s_bdi != &noop_backing_dev_info);
 	sb->s_bdi = bdi;
+	sb->s_iflags |= SB_I_PERSB_BDI;
 
 	return 0;
 }
@@ -1616,11 +1649,9 @@
 		percpu_rwsem_acquire(sb->s_writers.rw_sem + level, 0, _THIS_IP_);
 }
 
-static void sb_freeze_unlock(struct super_block *sb)
+static void sb_freeze_unlock(struct super_block *sb, int level)
 {
-	int level;
-
-	for (level = SB_FREEZE_LEVELS - 1; level >= 0; level--)
+	for (level--; level >= 0; level--)
 		percpu_up_write(sb->s_writers.rw_sem + level);
 }
 
@@ -1691,7 +1722,14 @@
 	sb_wait_write(sb, SB_FREEZE_PAGEFAULT);
 
 	/* All writers are done so after syncing there won't be dirty data */
-	sync_filesystem(sb);
+	ret = sync_filesystem(sb);
+	if (ret) {
+		sb->s_writers.frozen = SB_UNFROZEN;
+		sb_freeze_unlock(sb, SB_FREEZE_PAGEFAULT);
+		wake_up(&sb->s_writers.wait_unfrozen);
+		deactivate_locked_super(sb);
+		return ret;
+	}
 
 	/* Now wait for internal filesystem counter */
 	sb->s_writers.frozen = SB_FREEZE_FS;
@@ -1703,7 +1741,7 @@
 			printk(KERN_ERR
 				"VFS:Filesystem freeze failed\n");
 			sb->s_writers.frozen = SB_UNFROZEN;
-			sb_freeze_unlock(sb);
+			sb_freeze_unlock(sb, SB_FREEZE_FS);
 			wake_up(&sb->s_writers.wait_unfrozen);
 			deactivate_locked_super(sb);
 			return ret;
@@ -1748,7 +1786,7 @@
 	}
 
 	sb->s_writers.frozen = SB_UNFROZEN;
-	sb_freeze_unlock(sb);
+	sb_freeze_unlock(sb, SB_FREEZE_FS);
 out:
 	wake_up(&sb->s_writers.wait_unfrozen);
 	deactivate_locked_super(sb);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/sync.c
+++ linux-xilinx-zynqmp-5.15.0/fs/sync.c
@@ -28,7 +28,7 @@
  * wait == 1 case since in that case write_inode() functions do
  * sync_dirty_buffer() and thus effectively write one block at a time.
  */
-static int __sync_filesystem(struct super_block *sb, int wait)
+int __sync_filesystem(struct super_block *sb, int wait)
 {
 	if (wait)
 		sync_inodes_sb(sb);
@@ -39,6 +39,7 @@
 		sb->s_op->sync_fs(sb, wait);
 	return __sync_blockdev(sb->s_bdev, wait);
 }
+EXPORT_SYMBOL_GPL(__sync_filesystem);
 
 /*
  * Write out and wait upon all dirty data associated with this
@@ -81,21 +82,6 @@
 		sb->s_op->sync_fs(sb, *(int *)arg);
 }
 
-static void fdatawrite_one_bdev(struct block_device *bdev, void *arg)
-{
-	filemap_fdatawrite(bdev->bd_inode->i_mapping);
-}
-
-static void fdatawait_one_bdev(struct block_device *bdev, void *arg)
-{
-	/*
-	 * We keep the error status of individual mapping so that
-	 * applications can catch the writeback error using fsync(2).
-	 * See filemap_fdatawait_keep_errors() for details.
-	 */
-	filemap_fdatawait_keep_errors(bdev->bd_inode->i_mapping);
-}
-
 /*
  * Sync everything. We start by waking flusher threads so that most of
  * writeback runs on all devices in parallel. Then we sync all inodes reliably
@@ -114,8 +100,8 @@
 	iterate_supers(sync_inodes_one_sb, NULL);
 	iterate_supers(sync_fs_one_sb, &nowait);
 	iterate_supers(sync_fs_one_sb, &wait);
-	iterate_bdevs(fdatawrite_one_bdev, NULL);
-	iterate_bdevs(fdatawait_one_bdev, NULL);
+	sync_bdevs(false);
+	sync_bdevs(true);
 	if (unlikely(laptop_mode))
 		laptop_sync_completion();
 }
@@ -136,10 +122,10 @@
 	 */
 	iterate_supers(sync_inodes_one_sb, &nowait);
 	iterate_supers(sync_fs_one_sb, &nowait);
-	iterate_bdevs(fdatawrite_one_bdev, NULL);
+	sync_bdevs(false);
 	iterate_supers(sync_inodes_one_sb, &nowait);
 	iterate_supers(sync_fs_one_sb, &nowait);
-	iterate_bdevs(fdatawrite_one_bdev, NULL);
+	sync_bdevs(false);
 	printk("Emergency Sync complete\n");
 	kfree(work);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/sysfs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/sysfs/file.c
@@ -440,6 +440,8 @@
 	kn = kernfs_find_and_get(kobj->sd, attr->name);
 	if (kn)
 		kernfs_break_active_protection(kn);
+	else
+		kobject_put(kobj);
 	return kn;
 }
 EXPORT_SYMBOL_GPL(sysfs_break_active_protection);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/sysv/itree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/sysv/itree.c
@@ -82,9 +82,6 @@
 	return (sysv_zone_t*)((char*)bh->b_data + bh->b_size);
 }
 
-/*
- * Requires read_lock(&pointers_lock) or write_lock(&pointers_lock)
- */
 static Indirect *get_branch(struct inode *inode,
 			    int depth,
 			    int offsets[],
@@ -104,15 +101,18 @@
 		bh = sb_bread(sb, block);
 		if (!bh)
 			goto failure;
+		read_lock(&pointers_lock);
 		if (!verify_chain(chain, p))
 			goto changed;
 		add_chain(++p, bh, (sysv_zone_t*)bh->b_data + *++offsets);
+		read_unlock(&pointers_lock);
 		if (!p->key)
 			goto no_block;
 	}
 	return NULL;
 
 changed:
+	read_unlock(&pointers_lock);
 	brelse(bh);
 	*err = -EAGAIN;
 	goto no_block;
@@ -145,6 +145,10 @@
 		 */
 		parent = block_to_cpu(SYSV_SB(inode->i_sb), branch[n-1].key);
 		bh = sb_getblk(inode->i_sb, parent);
+		if (!bh) {
+			sysv_free_block(inode->i_sb, branch[n].key);
+			break;
+		}
 		lock_buffer(bh);
 		memset(bh->b_data, 0, blocksize);
 		branch[n].bh = bh;
@@ -214,9 +218,7 @@
 		goto out;
 
 reread:
-	read_lock(&pointers_lock);
 	partial = get_branch(inode, depth, offsets, chain, &err);
-	read_unlock(&pointers_lock);
 
 	/* Simplest case - block found, no allocation needed */
 	if (!partial) {
@@ -286,9 +288,9 @@
 	*top = 0;
 	for (k = depth; k > 1 && !offsets[k-1]; k--)
 		;
+	partial = get_branch(inode, k, offsets, chain, &err);
 
 	write_lock(&pointers_lock);
-	partial = get_branch(inode, k, offsets, chain, &err);
 	if (!partial)
 		partial = chain + k-1;
 	/*
@@ -438,7 +440,7 @@
 		res += blocks;
 		direct = 1;
 	}
-	return blocks;
+	return res;
 }
 
 int sysv_getattr(struct user_namespace *mnt_userns, const struct path *path,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/tracefs/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/tracefs/inode.c
@@ -141,6 +141,8 @@
 	kuid_t uid;
 	kgid_t gid;
 	umode_t mode;
+	/* Opt_* bitfield. */
+	unsigned int opts;
 };
 
 enum {
@@ -161,6 +163,77 @@
 	struct tracefs_mount_opts mount_opts;
 };
 
+static void change_gid(struct dentry *dentry, kgid_t gid)
+{
+	if (!dentry->d_inode)
+		return;
+	dentry->d_inode->i_gid = gid;
+}
+
+/*
+ * Taken from d_walk, but without he need for handling renames.
+ * Nothing can be renamed while walking the list, as tracefs
+ * does not support renames. This is only called when mounting
+ * or remounting the file system, to set all the files to
+ * the given gid.
+ */
+static void set_gid(struct dentry *parent, kgid_t gid)
+{
+	struct dentry *this_parent;
+	struct list_head *next;
+
+	this_parent = parent;
+	spin_lock(&this_parent->d_lock);
+
+	change_gid(this_parent, gid);
+repeat:
+	next = this_parent->d_subdirs.next;
+resume:
+	while (next != &this_parent->d_subdirs) {
+		struct list_head *tmp = next;
+		struct dentry *dentry = list_entry(tmp, struct dentry, d_child);
+		next = tmp->next;
+
+		spin_lock_nested(&dentry->d_lock, DENTRY_D_LOCK_NESTED);
+
+		change_gid(dentry, gid);
+
+		if (!list_empty(&dentry->d_subdirs)) {
+			spin_unlock(&this_parent->d_lock);
+			spin_release(&dentry->d_lock.dep_map, _RET_IP_);
+			this_parent = dentry;
+			spin_acquire(&this_parent->d_lock.dep_map, 0, 1, _RET_IP_);
+			goto repeat;
+		}
+		spin_unlock(&dentry->d_lock);
+	}
+	/*
+	 * All done at this level ... ascend and resume the search.
+	 */
+	rcu_read_lock();
+ascend:
+	if (this_parent != parent) {
+		struct dentry *child = this_parent;
+		this_parent = child->d_parent;
+
+		spin_unlock(&child->d_lock);
+		spin_lock(&this_parent->d_lock);
+
+		/* go into the first sibling still alive */
+		do {
+			next = child->d_child.next;
+			if (next == &this_parent->d_subdirs)
+				goto ascend;
+			child = list_entry(next, struct dentry, d_child);
+		} while (unlikely(child->d_flags & DCACHE_DENTRY_KILLED));
+		rcu_read_unlock();
+		goto resume;
+	}
+	rcu_read_unlock();
+	spin_unlock(&this_parent->d_lock);
+	return;
+}
+
 static int tracefs_parse_options(char *data, struct tracefs_mount_opts *opts)
 {
 	substring_t args[MAX_OPT_ARGS];
@@ -170,6 +243,7 @@
 	kgid_t gid;
 	char *p;
 
+	opts->opts = 0;
 	opts->mode = TRACEFS_DEFAULT_MODE;
 
 	while ((p = strsep(&data, ",")) != NULL) {
@@ -204,22 +278,36 @@
 		 * but traditionally tracefs has ignored all mount options
 		 */
 		}
+
+		opts->opts |= BIT(token);
 	}
 
 	return 0;
 }
 
-static int tracefs_apply_options(struct super_block *sb)
+static int tracefs_apply_options(struct super_block *sb, bool remount)
 {
 	struct tracefs_fs_info *fsi = sb->s_fs_info;
 	struct inode *inode = sb->s_root->d_inode;
 	struct tracefs_mount_opts *opts = &fsi->mount_opts;
 
-	inode->i_mode &= ~S_IALLUGO;
-	inode->i_mode |= opts->mode;
+	/*
+	 * On remount, only reset mode/uid/gid if they were provided as mount
+	 * options.
+	 */
+
+	if (!remount || opts->opts & BIT(Opt_mode)) {
+		inode->i_mode &= ~S_IALLUGO;
+		inode->i_mode |= opts->mode;
+	}
 
-	inode->i_uid = opts->uid;
-	inode->i_gid = opts->gid;
+	if (!remount || opts->opts & BIT(Opt_uid))
+		inode->i_uid = opts->uid;
+
+	if (!remount || opts->opts & BIT(Opt_gid)) {
+		/* Set all the group ids to the mount option */
+		set_gid(sb->s_root, opts->gid);
+	}
 
 	return 0;
 }
@@ -234,7 +322,7 @@
 	if (err)
 		goto fail;
 
-	tracefs_apply_options(sb);
+	tracefs_apply_options(sb, true);
 
 fail:
 	return err;
@@ -286,7 +374,7 @@
 
 	sb->s_op = &tracefs_super_operations;
 
-	tracefs_apply_options(sb);
+	tracefs_apply_options(sb, false);
 
 	return 0;
 
@@ -414,6 +502,8 @@
 	inode->i_mode = mode;
 	inode->i_fop = fops ? fops : &tracefs_file_operations;
 	inode->i_private = data;
+	inode->i_uid = d_inode(dentry->d_parent)->i_uid;
+	inode->i_gid = d_inode(dentry->d_parent)->i_gid;
 	d_instantiate(dentry, inode);
 	fsnotify_create(dentry->d_parent->d_inode, dentry);
 	return end_creating(dentry);
@@ -432,9 +522,12 @@
 	if (unlikely(!inode))
 		return failed_creating(dentry);
 
-	inode->i_mode = S_IFDIR | S_IRWXU | S_IRUGO | S_IXUGO;
+	/* Do not set bits for OTH */
+	inode->i_mode = S_IFDIR | S_IRWXU | S_IRUSR| S_IRGRP | S_IXUSR | S_IXGRP;
 	inode->i_op = ops;
 	inode->i_fop = &simple_dir_operations;
+	inode->i_uid = d_inode(dentry->d_parent)->i_uid;
+	inode->i_gid = d_inode(dentry->d_parent)->i_gid;
 
 	/* directory inodes start off with i_nlink == 2 (for "." entry) */
 	inc_nlink(inode);
@@ -463,6 +556,9 @@
  */
 struct dentry *tracefs_create_dir(const char *name, struct dentry *parent)
 {
+	if (security_locked_down(LOCKDOWN_TRACEFS))
+		return NULL;
+
 	return __create_dir(name, parent, &simple_dir_inode_operations);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/budget.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/budget.c
@@ -212,11 +212,10 @@
 	subtract_lebs += 1;
 
 	/*
-	 * The GC journal head LEB is not really accessible. And since
-	 * different write types go to different heads, we may count only on
-	 * one head's space.
+	 * Since different write types go to different heads, we should
+	 * reserve one leb for each head.
 	 */
-	subtract_lebs += c->jhead_cnt - 1;
+	subtract_lebs += c->jhead_cnt;
 
 	/* We also reserve one LEB for deletions, which bypass budgeting */
 	subtract_lebs += 1;
@@ -403,7 +402,7 @@
 	dd_growth = req->dirtied_page ? c->bi.page_budget : 0;
 
 	if (req->dirtied_ino)
-		dd_growth += c->bi.inode_budget << (req->dirtied_ino - 1);
+		dd_growth += c->bi.inode_budget * req->dirtied_ino;
 	if (req->mod_dent)
 		dd_growth += c->bi.dent_budget;
 	dd_growth += req->dirtied_ino_d;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/debug.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/debug.c
@@ -946,16 +946,20 @@
 
 	pr_err("\n");
 	pr_err("(pid %d) start dumping TNC tree\n", current->pid);
-	znode = ubifs_tnc_levelorder_next(c, c->zroot.znode, NULL);
-	level = znode->level;
-	pr_err("== Level %d ==\n", level);
-	while (znode) {
-		if (level != znode->level) {
-			level = znode->level;
-			pr_err("== Level %d ==\n", level);
+	if (c->zroot.znode) {
+		znode = ubifs_tnc_levelorder_next(c, c->zroot.znode, NULL);
+		level = znode->level;
+		pr_err("== Level %d ==\n", level);
+		while (znode) {
+			if (level != znode->level) {
+				level = znode->level;
+				pr_err("== Level %d ==\n", level);
+			}
+			ubifs_dump_znode(c, znode);
+			znode = ubifs_tnc_levelorder_next(c, c->zroot.znode, znode);
 		}
-		ubifs_dump_znode(c, znode);
-		znode = ubifs_tnc_levelorder_next(c, c->zroot.znode, znode);
+	} else {
+		pr_err("empty TNC tree in memory\n");
 	}
 	pr_err("(pid %d) finish dumping TNC tree\n", current->pid);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/dir.c
@@ -68,13 +68,14 @@
  * @c: UBIFS file-system description object
  * @dir: parent directory inode
  * @mode: inode mode flags
+ * @is_xattr: whether the inode is xattr inode
  *
  * This function finds an unused inode number, allocates new inode and
  * initializes it. Returns new inode in case of success and an error code in
  * case of failure.
  */
 struct inode *ubifs_new_inode(struct ubifs_info *c, struct inode *dir,
-			      umode_t mode)
+			      umode_t mode, bool is_xattr)
 {
 	int err;
 	struct inode *inode;
@@ -99,10 +100,12 @@
 			 current_time(inode);
 	inode->i_mapping->nrpages = 0;
 
-	err = fscrypt_prepare_new_inode(dir, inode, &encrypted);
-	if (err) {
-		ubifs_err(c, "fscrypt_prepare_new_inode failed: %i", err);
-		goto out_iput;
+	if (!is_xattr) {
+		err = fscrypt_prepare_new_inode(dir, inode, &encrypted);
+		if (err) {
+			ubifs_err(c, "fscrypt_prepare_new_inode failed: %i", err);
+			goto out_iput;
+		}
 	}
 
 	switch (mode & S_IFMT) {
@@ -309,7 +312,7 @@
 
 	sz_change = CALC_DENT_SIZE(fname_len(&nm));
 
-	inode = ubifs_new_inode(c, dir, mode);
+	inode = ubifs_new_inode(c, dir, mode, false);
 	if (IS_ERR(inode)) {
 		err = PTR_ERR(inode);
 		goto out_fname;
@@ -349,20 +352,91 @@
 	return err;
 }
 
-static int do_tmpfile(struct inode *dir, struct dentry *dentry,
-		      umode_t mode, struct inode **whiteout)
+static struct inode *create_whiteout(struct inode *dir, struct dentry *dentry)
 {
+	int err;
+	umode_t mode = S_IFCHR | WHITEOUT_MODE;
 	struct inode *inode;
 	struct ubifs_info *c = dir->i_sb->s_fs_info;
-	struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1};
+
+	/*
+	 * Create an inode('nlink = 1') for whiteout without updating journal,
+	 * let ubifs_jnl_rename() store it on flash to complete rename whiteout
+	 * atomically.
+	 */
+
+	dbg_gen("dent '%pd', mode %#hx in dir ino %lu",
+		dentry, mode, dir->i_ino);
+
+	inode = ubifs_new_inode(c, dir, mode, false);
+	if (IS_ERR(inode)) {
+		err = PTR_ERR(inode);
+		goto out_free;
+	}
+
+	init_special_inode(inode, inode->i_mode, WHITEOUT_DEV);
+	ubifs_assert(c, inode->i_op == &ubifs_file_inode_operations);
+
+	err = ubifs_init_security(dir, inode, &dentry->d_name);
+	if (err)
+		goto out_inode;
+
+	/* The dir size is updated by do_rename. */
+	insert_inode_hash(inode);
+
+	return inode;
+
+out_inode:
+	make_bad_inode(inode);
+	iput(inode);
+out_free:
+	ubifs_err(c, "cannot create whiteout file, error %d", err);
+	return ERR_PTR(err);
+}
+
+/**
+ * lock_2_inodes - a wrapper for locking two UBIFS inodes.
+ * @inode1: first inode
+ * @inode2: second inode
+ *
+ * We do not implement any tricks to guarantee strict lock ordering, because
+ * VFS has already done it for us on the @i_mutex. So this is just a simple
+ * wrapper function.
+ */
+static void lock_2_inodes(struct inode *inode1, struct inode *inode2)
+{
+	mutex_lock_nested(&ubifs_inode(inode1)->ui_mutex, WB_MUTEX_1);
+	mutex_lock_nested(&ubifs_inode(inode2)->ui_mutex, WB_MUTEX_2);
+}
+
+/**
+ * unlock_2_inodes - a wrapper for unlocking two UBIFS inodes.
+ * @inode1: first inode
+ * @inode2: second inode
+ */
+static void unlock_2_inodes(struct inode *inode1, struct inode *inode2)
+{
+	mutex_unlock(&ubifs_inode(inode2)->ui_mutex);
+	mutex_unlock(&ubifs_inode(inode1)->ui_mutex);
+}
+
+static int ubifs_tmpfile(struct user_namespace *mnt_userns, struct inode *dir,
+			 struct dentry *dentry, umode_t mode)
+{
+	struct inode *inode;
+	struct ubifs_info *c = dir->i_sb->s_fs_info;
+	struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1,
+					.dirtied_ino = 1};
 	struct ubifs_budget_req ino_req = { .dirtied_ino = 1 };
-	struct ubifs_inode *ui, *dir_ui = ubifs_inode(dir);
+	struct ubifs_inode *ui;
 	int err, instantiated = 0;
 	struct fscrypt_name nm;
 
 	/*
-	 * Budget request settings: new dirty inode, new direntry,
-	 * budget for dirtied inode will be released via writeback.
+	 * Budget request settings: new inode, new direntry, changing the
+	 * parent directory inode.
+	 * Allocate budget separately for new dirtied inode, the budget will
+	 * be released via writeback.
 	 */
 
 	dbg_gen("dent '%pd', mode %#hx in dir ino %lu",
@@ -385,49 +459,38 @@
 		return err;
 	}
 
-	inode = ubifs_new_inode(c, dir, mode);
+	inode = ubifs_new_inode(c, dir, mode, false);
 	if (IS_ERR(inode)) {
 		err = PTR_ERR(inode);
 		goto out_budg;
 	}
 	ui = ubifs_inode(inode);
 
-	if (whiteout) {
-		init_special_inode(inode, inode->i_mode, WHITEOUT_DEV);
-		ubifs_assert(c, inode->i_op == &ubifs_file_inode_operations);
-	}
-
 	err = ubifs_init_security(dir, inode, &dentry->d_name);
 	if (err)
 		goto out_inode;
 
 	mutex_lock(&ui->ui_mutex);
 	insert_inode_hash(inode);
-
-	if (whiteout) {
-		mark_inode_dirty(inode);
-		drop_nlink(inode);
-		*whiteout = inode;
-	} else {
-		d_tmpfile(dentry, inode);
-	}
+	d_tmpfile(dentry, inode);
 	ubifs_assert(c, ui->dirty);
 
 	instantiated = 1;
 	mutex_unlock(&ui->ui_mutex);
 
-	mutex_lock(&dir_ui->ui_mutex);
+	lock_2_inodes(dir, inode);
 	err = ubifs_jnl_update(c, dir, &nm, inode, 1, 0);
 	if (err)
 		goto out_cancel;
-	mutex_unlock(&dir_ui->ui_mutex);
+	unlock_2_inodes(dir, inode);
 
 	ubifs_release_budget(c, &req);
+	fscrypt_free_filename(&nm);
 
 	return 0;
 
 out_cancel:
-	mutex_unlock(&dir_ui->ui_mutex);
+	unlock_2_inodes(dir, inode);
 out_inode:
 	make_bad_inode(inode);
 	if (!instantiated)
@@ -441,12 +504,6 @@
 	return err;
 }
 
-static int ubifs_tmpfile(struct user_namespace *mnt_userns, struct inode *dir,
-			 struct dentry *dentry, umode_t mode)
-{
-	return do_tmpfile(dir, dentry, mode, NULL);
-}
-
 /**
  * vfs_dent_type - get VFS directory entry type.
  * @type: UBIFS directory entry type
@@ -660,32 +717,6 @@
 	return 0;
 }
 
-/**
- * lock_2_inodes - a wrapper for locking two UBIFS inodes.
- * @inode1: first inode
- * @inode2: second inode
- *
- * We do not implement any tricks to guarantee strict lock ordering, because
- * VFS has already done it for us on the @i_mutex. So this is just a simple
- * wrapper function.
- */
-static void lock_2_inodes(struct inode *inode1, struct inode *inode2)
-{
-	mutex_lock_nested(&ubifs_inode(inode1)->ui_mutex, WB_MUTEX_1);
-	mutex_lock_nested(&ubifs_inode(inode2)->ui_mutex, WB_MUTEX_2);
-}
-
-/**
- * unlock_2_inodes - a wrapper for unlocking two UBIFS inodes.
- * @inode1: first inode
- * @inode2: second inode
- */
-static void unlock_2_inodes(struct inode *inode1, struct inode *inode2)
-{
-	mutex_unlock(&ubifs_inode(inode2)->ui_mutex);
-	mutex_unlock(&ubifs_inode(inode1)->ui_mutex);
-}
-
 static int ubifs_link(struct dentry *old_dentry, struct inode *dir,
 		      struct dentry *dentry)
 {
@@ -949,7 +980,8 @@
 	struct ubifs_inode *dir_ui = ubifs_inode(dir);
 	struct ubifs_info *c = dir->i_sb->s_fs_info;
 	int err, sz_change;
-	struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1 };
+	struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1,
+					.dirtied_ino = 1};
 	struct fscrypt_name nm;
 
 	/*
@@ -970,7 +1002,7 @@
 
 	sz_change = CALC_DENT_SIZE(fname_len(&nm));
 
-	inode = ubifs_new_inode(c, dir, S_IFDIR | mode);
+	inode = ubifs_new_inode(c, dir, S_IFDIR | mode, false);
 	if (IS_ERR(inode)) {
 		err = PTR_ERR(inode);
 		goto out_fname;
@@ -1057,7 +1089,7 @@
 
 	sz_change = CALC_DENT_SIZE(fname_len(&nm));
 
-	inode = ubifs_new_inode(c, dir, mode);
+	inode = ubifs_new_inode(c, dir, mode, false);
 	if (IS_ERR(inode)) {
 		kfree(dev);
 		err = PTR_ERR(inode);
@@ -1113,7 +1145,6 @@
 	int err, sz_change, len = strlen(symname);
 	struct fscrypt_str disk_link;
 	struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1,
-					.new_ino_d = ALIGN(len, 8),
 					.dirtied_ino = 1 };
 	struct fscrypt_name nm;
 
@@ -1129,6 +1160,7 @@
 	 * Budget request settings: new inode, new direntry and changing parent
 	 * directory inode.
 	 */
+	req.new_ino_d = ALIGN(disk_link.len - 1, 8);
 	err = ubifs_budget_space(c, &req);
 	if (err)
 		return err;
@@ -1139,7 +1171,7 @@
 
 	sz_change = CALC_DENT_SIZE(fname_len(&nm));
 
-	inode = ubifs_new_inode(c, dir, S_IFLNK | S_IRWXUGO);
+	inode = ubifs_new_inode(c, dir, S_IFLNK | S_IRWXUGO, false);
 	if (IS_ERR(inode)) {
 		err = PTR_ERR(inode);
 		goto out_fname;
@@ -1193,6 +1225,8 @@
 	dir_ui->ui_size = dir->i_size;
 	mutex_unlock(&dir_ui->ui_mutex);
 out_inode:
+	/* Free inode->i_link before inode is marked as bad. */
+	fscrypt_free_inode(inode);
 	make_bad_inode(inode);
 	iput(inode);
 out_fname:
@@ -1264,17 +1298,19 @@
 					.dirtied_ino = 3 };
 	struct ubifs_budget_req ino_req = { .dirtied_ino = 1,
 			.dirtied_ino_d = ALIGN(old_inode_ui->data_len, 8) };
+	struct ubifs_budget_req wht_req;
 	struct timespec64 time;
 	unsigned int saved_nlink;
 	struct fscrypt_name old_nm, new_nm;
 
 	/*
-	 * Budget request settings: deletion direntry, new direntry, removing
-	 * the old inode, and changing old and new parent directory inodes.
+	 * Budget request settings:
+	 *   req: deletion direntry, new direntry, removing the old inode,
+	 *   and changing old and new parent directory inodes.
 	 *
-	 * However, this operation also marks the target inode as dirty and
-	 * does not write it, so we allocate budget for the target inode
-	 * separately.
+	 *   wht_req: new whiteout inode for RENAME_WHITEOUT.
+	 *
+	 *   ino_req: marks the target inode as dirty and does not write it.
 	 */
 
 	dbg_gen("dent '%pd' ino %lu in dir ino %lu to dent '%pd' in dir ino %lu flags 0x%x",
@@ -1284,6 +1320,8 @@
 	if (unlink) {
 		ubifs_assert(c, inode_is_locked(new_inode));
 
+		/* Budget for old inode's data when its nlink > 1. */
+		req.dirtied_ino_d = ALIGN(ubifs_inode(new_inode)->data_len, 8);
 		err = ubifs_purge_xattrs(new_inode);
 		if (err)
 			return err;
@@ -1331,20 +1369,44 @@
 			goto out_release;
 		}
 
-		err = do_tmpfile(old_dir, old_dentry, S_IFCHR | WHITEOUT_MODE, &whiteout);
-		if (err) {
+		/*
+		 * The whiteout inode without dentry is pinned in memory,
+		 * umount won't happen during rename process because we
+		 * got parent dentry.
+		 */
+		whiteout = create_whiteout(old_dir, old_dentry);
+		if (IS_ERR(whiteout)) {
+			err = PTR_ERR(whiteout);
 			kfree(dev);
 			goto out_release;
 		}
 
-		spin_lock(&whiteout->i_lock);
-		whiteout->i_state |= I_LINKABLE;
-		spin_unlock(&whiteout->i_lock);
-
 		whiteout_ui = ubifs_inode(whiteout);
 		whiteout_ui->data = dev;
 		whiteout_ui->data_len = ubifs_encode_dev(dev, MKDEV(0, 0));
 		ubifs_assert(c, !whiteout_ui->dirty);
+
+		memset(&wht_req, 0, sizeof(struct ubifs_budget_req));
+		wht_req.new_ino = 1;
+		wht_req.new_ino_d = ALIGN(whiteout_ui->data_len, 8);
+		/*
+		 * To avoid deadlock between space budget (holds ui_mutex and
+		 * waits wb work) and writeback work(waits ui_mutex), do space
+		 * budget before ubifs inodes locked.
+		 */
+		err = ubifs_budget_space(c, &wht_req);
+		if (err) {
+			/*
+			 * Whiteout inode can not be written on flash by
+			 * ubifs_jnl_write_inode(), because it's neither
+			 * dirty nor zero-nlink.
+			 */
+			iput(whiteout);
+			goto out_release;
+		}
+
+		/* Add the old_dentry size to the old_dir size. */
+		old_sz -= CALC_DENT_SIZE(fname_len(&old_nm));
 	}
 
 	lock_4_inodes(old_dir, new_dir, new_inode, whiteout);
@@ -1416,29 +1478,11 @@
 		sync = IS_DIRSYNC(old_dir) || IS_DIRSYNC(new_dir);
 		if (unlink && IS_SYNC(new_inode))
 			sync = 1;
-	}
-
-	if (whiteout) {
-		struct ubifs_budget_req wht_req = { .dirtied_ino = 1,
-				.dirtied_ino_d = \
-				ALIGN(ubifs_inode(whiteout)->data_len, 8) };
-
-		err = ubifs_budget_space(c, &wht_req);
-		if (err) {
-			kfree(whiteout_ui->data);
-			whiteout_ui->data_len = 0;
-			iput(whiteout);
-			goto out_release;
-		}
-
-		inc_nlink(whiteout);
-		mark_inode_dirty(whiteout);
-
-		spin_lock(&whiteout->i_lock);
-		whiteout->i_state &= ~I_LINKABLE;
-		spin_unlock(&whiteout->i_lock);
-
-		iput(whiteout);
+		/*
+		 * S_SYNC flag of whiteout inherits from the old_dir, and we
+		 * have already checked the old dir inode. So there is no need
+		 * to check whiteout.
+		 */
 	}
 
 	err = ubifs_jnl_rename(c, old_dir, old_inode, &old_nm, new_dir,
@@ -1449,6 +1493,11 @@
 	unlock_4_inodes(old_dir, new_dir, new_inode, whiteout);
 	ubifs_release_budget(c, &req);
 
+	if (whiteout) {
+		ubifs_release_budget(c, &wht_req);
+		iput(whiteout);
+	}
+
 	mutex_lock(&old_inode_ui->ui_mutex);
 	release = old_inode_ui->dirty;
 	mark_inode_dirty_sync(old_inode);
@@ -1457,11 +1506,16 @@
 	if (release)
 		ubifs_release_budget(c, &ino_req);
 	if (IS_SYNC(old_inode))
-		err = old_inode->i_sb->s_op->write_inode(old_inode, NULL);
+		/*
+		 * Rename finished here. Although old inode cannot be updated
+		 * on flash, old ctime is not a big problem, don't return err
+		 * code to userspace.
+		 */
+		old_inode->i_sb->s_op->write_inode(old_inode, NULL);
 
 	fscrypt_free_filename(&old_nm);
 	fscrypt_free_filename(&new_nm);
-	return err;
+	return 0;
 
 out_cancel:
 	if (unlink) {
@@ -1482,11 +1536,11 @@
 				inc_nlink(old_dir);
 		}
 	}
+	unlock_4_inodes(old_dir, new_dir, new_inode, whiteout);
 	if (whiteout) {
-		drop_nlink(whiteout);
+		ubifs_release_budget(c, &wht_req);
 		iput(whiteout);
 	}
-	unlock_4_inodes(old_dir, new_dir, new_inode, whiteout);
 out_release:
 	ubifs_release_budget(c, &ino_req);
 	ubifs_release_budget(c, &req);
@@ -1520,6 +1574,10 @@
 		return err;
 	}
 
+	err = ubifs_budget_space(c, &req);
+	if (err)
+		goto out;
+
 	lock_4_inodes(old_dir, new_dir, NULL, NULL);
 
 	time = current_time(old_dir);
@@ -1545,6 +1603,7 @@
 	unlock_4_inodes(old_dir, new_dir, NULL, NULL);
 	ubifs_release_budget(c, &req);
 
+out:
 	fscrypt_free_filename(&fst_nm);
 	fscrypt_free_filename(&snd_nm);
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/file.c
@@ -262,9 +262,6 @@
 				return err;
 			}
 		}
-
-		SetPageUptodate(page);
-		ClearPageError(page);
 	}
 
 	if (PagePrivate(page))
@@ -463,9 +460,6 @@
 				return err;
 			}
 		}
-
-		SetPageUptodate(page);
-		ClearPageError(page);
 	}
 
 	err = allocate_budget(c, page, ui, appending);
@@ -475,10 +469,8 @@
 		 * If we skipped reading the page because we were going to
 		 * write all of it, then it is not up to date.
 		 */
-		if (skipped_read) {
+		if (skipped_read)
 			ClearPageChecked(page);
-			ClearPageUptodate(page);
-		}
 		/*
 		 * Budgeting failed which means it would have to force
 		 * write-back but didn't, because we set the @fast flag in the
@@ -569,8 +561,11 @@
 		goto out;
 	}
 
+	if (len == PAGE_SIZE)
+		SetPageUptodate(page);
+
 	if (!PagePrivate(page)) {
-		SetPagePrivate(page);
+		attach_page_private(page, (void *)1);
 		atomic_long_inc(&c->dirty_pg_cnt);
 		__set_page_dirty_nobuffers(page);
 	}
@@ -947,7 +942,7 @@
 		release_existing_page_budget(c);
 
 	atomic_long_dec(&c->dirty_pg_cnt);
-	ClearPagePrivate(page);
+	detach_page_private(page);
 	ClearPageChecked(page);
 
 	kunmap(page);
@@ -1031,7 +1026,7 @@
 		if (page->index >= synced_i_size >> PAGE_SHIFT) {
 			err = inode->i_sb->s_op->write_inode(inode, NULL);
 			if (err)
-				goto out_unlock;
+				goto out_redirty;
 			/*
 			 * The inode has been written, but the write-buffer has
 			 * not been synchronized, so in case of an unclean
@@ -1059,11 +1054,17 @@
 	if (i_size > synced_i_size) {
 		err = inode->i_sb->s_op->write_inode(inode, NULL);
 		if (err)
-			goto out_unlock;
+			goto out_redirty;
 	}
 
 	return do_writepage(page, len);
-
+out_redirty:
+	/*
+	 * redirty_page_for_writepage() won't call ubifs_dirty_inode() because
+	 * it passes I_DIRTY_PAGES flag while calling __mark_inode_dirty(), so
+	 * there is no need to do space budget for dirty inode.
+	 */
+	redirty_page_for_writepage(wbc, page);
 out_unlock:
 	unlock_page(page);
 	return err;
@@ -1304,7 +1305,7 @@
 		release_existing_page_budget(c);
 
 	atomic_long_dec(&c->dirty_pg_cnt);
-	ClearPagePrivate(page);
+	detach_page_private(page);
 	ClearPageChecked(page);
 }
 
@@ -1471,8 +1472,8 @@
 		return rc;
 
 	if (PagePrivate(page)) {
-		ClearPagePrivate(page);
-		SetPagePrivate(newpage);
+		detach_page_private(page);
+		attach_page_private(newpage, (void *)1);
 	}
 
 	if (mode != MIGRATE_SYNC_NO_COPY)
@@ -1496,7 +1497,7 @@
 		return 0;
 	ubifs_assert(c, PagePrivate(page));
 	ubifs_assert(c, 0);
-	ClearPagePrivate(page);
+	detach_page_private(page);
 	ClearPageChecked(page);
 	return 1;
 }
@@ -1567,7 +1568,7 @@
 	else {
 		if (!PageChecked(page))
 			ubifs_convert_page_budget(c);
-		SetPagePrivate(page);
+		attach_page_private(page, (void *)1);
 		atomic_long_inc(&c->dirty_pg_cnt);
 		__set_page_dirty_nobuffers(page);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/io.c
@@ -833,16 +833,42 @@
 	 */
 	n = aligned_len >> c->max_write_shift;
 	if (n) {
-		n <<= c->max_write_shift;
+		int m = n - 1;
+
 		dbg_io("write %d bytes to LEB %d:%d", n, wbuf->lnum,
 		       wbuf->offs);
-		err = ubifs_leb_write(c, wbuf->lnum, buf + written,
-				      wbuf->offs, n);
+
+		if (m) {
+			/* '(n-1)<<c->max_write_shift < len' is always true. */
+			m <<= c->max_write_shift;
+			err = ubifs_leb_write(c, wbuf->lnum, buf + written,
+					      wbuf->offs, m);
+			if (err)
+				goto out;
+			wbuf->offs += m;
+			aligned_len -= m;
+			len -= m;
+			written += m;
+		}
+
+		/*
+		 * The non-written len of buf may be less than 'n' because
+		 * parameter 'len' is not 8 bytes aligned, so here we read
+		 * min(len, n) bytes from buf.
+		 */
+		n = 1 << c->max_write_shift;
+		memcpy(wbuf->buf, buf + written, min(len, n));
+		if (n > len) {
+			ubifs_assert(c, n - len < 8);
+			ubifs_pad(c, wbuf->buf + len, n - len);
+		}
+
+		err = ubifs_leb_write(c, wbuf->lnum, wbuf->buf, wbuf->offs, n);
 		if (err)
 			goto out;
 		wbuf->offs += n;
 		aligned_len -= n;
-		len -= n;
+		len -= min(len, n);
 		written += n;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/ioctl.c
@@ -108,7 +108,7 @@
 	struct ubifs_inode *ui = ubifs_inode(inode);
 	struct ubifs_info *c = inode->i_sb->s_fs_info;
 	struct ubifs_budget_req req = { .dirtied_ino = 1,
-					.dirtied_ino_d = ui->data_len };
+			.dirtied_ino_d = ALIGN(ui->data_len, 8) };
 
 	err = ubifs_budget_space(c, &req);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/journal.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/journal.c
@@ -1207,9 +1207,9 @@
  * @sync: non-zero if the write-buffer has to be synchronized
  *
  * This function implements the re-name operation which may involve writing up
- * to 4 inodes and 2 directory entries. It marks the written inodes as clean
- * and returns zero on success. In case of failure, a negative error code is
- * returned.
+ * to 4 inodes(new inode, whiteout inode, old and new parent directory inodes)
+ * and 2 directory entries. It marks the written inodes as clean and returns
+ * zero on success. In case of failure, a negative error code is returned.
  */
 int ubifs_jnl_rename(struct ubifs_info *c, const struct inode *old_dir,
 		     const struct inode *old_inode,
@@ -1222,14 +1222,15 @@
 	void *p;
 	union ubifs_key key;
 	struct ubifs_dent_node *dent, *dent2;
-	int err, dlen1, dlen2, ilen, lnum, offs, len, orphan_added = 0;
+	int err, dlen1, dlen2, ilen, wlen, lnum, offs, len, orphan_added = 0;
 	int aligned_dlen1, aligned_dlen2, plen = UBIFS_INO_NODE_SZ;
 	int last_reference = !!(new_inode && new_inode->i_nlink == 0);
 	int move = (old_dir != new_dir);
-	struct ubifs_inode *new_ui;
+	struct ubifs_inode *new_ui, *whiteout_ui;
 	u8 hash_old_dir[UBIFS_HASH_ARR_SZ];
 	u8 hash_new_dir[UBIFS_HASH_ARR_SZ];
 	u8 hash_new_inode[UBIFS_HASH_ARR_SZ];
+	u8 hash_whiteout_inode[UBIFS_HASH_ARR_SZ];
 	u8 hash_dent1[UBIFS_HASH_ARR_SZ];
 	u8 hash_dent2[UBIFS_HASH_ARR_SZ];
 
@@ -1249,9 +1250,20 @@
 	} else
 		ilen = 0;
 
+	if (whiteout) {
+		whiteout_ui = ubifs_inode(whiteout);
+		ubifs_assert(c, mutex_is_locked(&whiteout_ui->ui_mutex));
+		ubifs_assert(c, whiteout->i_nlink == 1);
+		ubifs_assert(c, !whiteout_ui->dirty);
+		wlen = UBIFS_INO_NODE_SZ;
+		wlen += whiteout_ui->data_len;
+	} else
+		wlen = 0;
+
 	aligned_dlen1 = ALIGN(dlen1, 8);
 	aligned_dlen2 = ALIGN(dlen2, 8);
-	len = aligned_dlen1 + aligned_dlen2 + ALIGN(ilen, 8) + ALIGN(plen, 8);
+	len = aligned_dlen1 + aligned_dlen2 + ALIGN(ilen, 8) +
+	      ALIGN(wlen, 8) + ALIGN(plen, 8);
 	if (move)
 		len += plen;
 
@@ -1313,6 +1325,15 @@
 		p += ALIGN(ilen, 8);
 	}
 
+	if (whiteout) {
+		pack_inode(c, p, whiteout, 0);
+		err = ubifs_node_calc_hash(c, p, hash_whiteout_inode);
+		if (err)
+			goto out_release;
+
+		p += ALIGN(wlen, 8);
+	}
+
 	if (!move) {
 		pack_inode(c, p, old_dir, 1);
 		err = ubifs_node_calc_hash(c, p, hash_old_dir);
@@ -1352,6 +1373,9 @@
 		if (new_inode)
 			ubifs_wbuf_add_ino_nolock(&c->jheads[BASEHD].wbuf,
 						  new_inode->i_ino);
+		if (whiteout)
+			ubifs_wbuf_add_ino_nolock(&c->jheads[BASEHD].wbuf,
+						  whiteout->i_ino);
 	}
 	release_head(c, BASEHD);
 
@@ -1368,8 +1392,6 @@
 		err = ubifs_tnc_add_nm(c, &key, lnum, offs, dlen2, hash_dent2, old_nm);
 		if (err)
 			goto out_ro;
-
-		ubifs_delete_orphan(c, whiteout->i_ino);
 	} else {
 		err = ubifs_add_dirt(c, lnum, dlen2);
 		if (err)
@@ -1390,6 +1412,15 @@
 		offs += ALIGN(ilen, 8);
 	}
 
+	if (whiteout) {
+		ino_key_init(c, &key, whiteout->i_ino);
+		err = ubifs_tnc_add(c, &key, lnum, offs, wlen,
+				    hash_whiteout_inode);
+		if (err)
+			goto out_ro;
+		offs += ALIGN(wlen, 8);
+	}
+
 	ino_key_init(c, &key, old_dir->i_ino);
 	err = ubifs_tnc_add(c, &key, lnum, offs, plen, hash_old_dir);
 	if (err)
@@ -1410,6 +1441,11 @@
 		new_ui->synced_i_size = new_ui->ui_size;
 		spin_unlock(&new_ui->ui_lock);
 	}
+	/*
+	 * No need to mark whiteout inode clean.
+	 * Whiteout doesn't have non-zero size, no need to update
+	 * synced_i_size for whiteout_ui.
+	 */
 	mark_inode_clean(c, ubifs_inode(old_dir));
 	if (move)
 		mark_inode_clean(c, ubifs_inode(new_dir));
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/super.c
@@ -777,10 +777,10 @@
 	 * necessary to report something for the 'statfs()' call.
 	 *
 	 * Subtract the LEB reserved for GC, the LEB which is reserved for
-	 * deletions, minimum LEBs for the index, and assume only one journal
-	 * head is available.
+	 * deletions, minimum LEBs for the index, the LEBs which are reserved
+	 * for each journal head.
 	 */
-	tmp64 = c->main_lebs - 1 - 1 - MIN_INDEX_LEBS - c->jhead_cnt + 1;
+	tmp64 = c->main_lebs - 1 - 1 - MIN_INDEX_LEBS - c->jhead_cnt;
 	tmp64 *= (long long)c->leb_size - c->leb_overhead;
 	tmp64 = ubifs_reported_space(c, tmp64);
 	c->block_cnt = tmp64 >> UBIFS_BLOCK_SHIFT;
@@ -833,7 +833,7 @@
 		INIT_LIST_HEAD(&c->jheads[i].buds_list);
 		err = ubifs_wbuf_init(c, &c->jheads[i].wbuf);
 		if (err)
-			return err;
+			goto out_wbuf;
 
 		c->jheads[i].wbuf.sync_callback = &bud_wbuf_callback;
 		c->jheads[i].wbuf.jhead = i;
@@ -841,7 +841,7 @@
 		c->jheads[i].log_hash = ubifs_hash_get_desc(c);
 		if (IS_ERR(c->jheads[i].log_hash)) {
 			err = PTR_ERR(c->jheads[i].log_hash);
-			goto out;
+			goto out_log_hash;
 		}
 	}
 
@@ -854,9 +854,18 @@
 
 	return 0;
 
-out:
-	while (i--)
+out_log_hash:
+	kfree(c->jheads[i].wbuf.buf);
+	kfree(c->jheads[i].wbuf.inodes);
+
+out_wbuf:
+	while (i--) {
+		kfree(c->jheads[i].wbuf.buf);
+		kfree(c->jheads[i].wbuf.inodes);
 		kfree(c->jheads[i].log_hash);
+	}
+	kfree(c->jheads);
+	c->jheads = NULL;
 
 	return err;
 }
@@ -1853,7 +1862,6 @@
 		kthread_stop(c->bgt);
 		c->bgt = NULL;
 	}
-	free_wbufs(c);
 	kfree(c->write_reserve_buf);
 	c->write_reserve_buf = NULL;
 	vfree(c->ileb_buf);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/tnc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/tnc.c
@@ -44,6 +44,33 @@
 	NOT_ON_MEDIA = 3,
 };
 
+static void do_insert_old_idx(struct ubifs_info *c,
+			      struct ubifs_old_idx *old_idx)
+{
+	struct ubifs_old_idx *o;
+	struct rb_node **p, *parent = NULL;
+
+	p = &c->old_idx.rb_node;
+	while (*p) {
+		parent = *p;
+		o = rb_entry(parent, struct ubifs_old_idx, rb);
+		if (old_idx->lnum < o->lnum)
+			p = &(*p)->rb_left;
+		else if (old_idx->lnum > o->lnum)
+			p = &(*p)->rb_right;
+		else if (old_idx->offs < o->offs)
+			p = &(*p)->rb_left;
+		else if (old_idx->offs > o->offs)
+			p = &(*p)->rb_right;
+		else {
+			ubifs_err(c, "old idx added twice!");
+			kfree(old_idx);
+		}
+	}
+	rb_link_node(&old_idx->rb, parent, p);
+	rb_insert_color(&old_idx->rb, &c->old_idx);
+}
+
 /**
  * insert_old_idx - record an index node obsoleted since the last commit start.
  * @c: UBIFS file-system description object
@@ -69,35 +96,15 @@
  */
 static int insert_old_idx(struct ubifs_info *c, int lnum, int offs)
 {
-	struct ubifs_old_idx *old_idx, *o;
-	struct rb_node **p, *parent = NULL;
+	struct ubifs_old_idx *old_idx;
 
 	old_idx = kmalloc(sizeof(struct ubifs_old_idx), GFP_NOFS);
 	if (unlikely(!old_idx))
 		return -ENOMEM;
 	old_idx->lnum = lnum;
 	old_idx->offs = offs;
+	do_insert_old_idx(c, old_idx);
 
-	p = &c->old_idx.rb_node;
-	while (*p) {
-		parent = *p;
-		o = rb_entry(parent, struct ubifs_old_idx, rb);
-		if (lnum < o->lnum)
-			p = &(*p)->rb_left;
-		else if (lnum > o->lnum)
-			p = &(*p)->rb_right;
-		else if (offs < o->offs)
-			p = &(*p)->rb_left;
-		else if (offs > o->offs)
-			p = &(*p)->rb_right;
-		else {
-			ubifs_err(c, "old idx added twice!");
-			kfree(old_idx);
-			return 0;
-		}
-	}
-	rb_link_node(&old_idx->rb, parent, p);
-	rb_insert_color(&old_idx->rb, &c->old_idx);
 	return 0;
 }
 
@@ -199,23 +206,6 @@
 	__set_bit(DIRTY_ZNODE, &zn->flags);
 	__clear_bit(COW_ZNODE, &zn->flags);
 
-	ubifs_assert(c, !ubifs_zn_obsolete(znode));
-	__set_bit(OBSOLETE_ZNODE, &znode->flags);
-
-	if (znode->level != 0) {
-		int i;
-		const int n = zn->child_cnt;
-
-		/* The children now have new parent */
-		for (i = 0; i < n; i++) {
-			struct ubifs_zbranch *zbr = &zn->zbranch[i];
-
-			if (zbr->znode)
-				zbr->znode->parent = zn;
-		}
-	}
-
-	atomic_long_inc(&c->dirty_zn_cnt);
 	return zn;
 }
 
@@ -234,6 +224,42 @@
 }
 
 /**
+ * replace_znode - replace old znode with new znode.
+ * @c: UBIFS file-system description object
+ * @new_zn: new znode
+ * @old_zn: old znode
+ * @zbr: the branch of parent znode
+ *
+ * Replace old znode with new znode in TNC.
+ */
+static void replace_znode(struct ubifs_info *c, struct ubifs_znode *new_zn,
+			  struct ubifs_znode *old_zn, struct ubifs_zbranch *zbr)
+{
+	ubifs_assert(c, !ubifs_zn_obsolete(old_zn));
+	__set_bit(OBSOLETE_ZNODE, &old_zn->flags);
+
+	if (old_zn->level != 0) {
+		int i;
+		const int n = new_zn->child_cnt;
+
+		/* The children now have new parent */
+		for (i = 0; i < n; i++) {
+			struct ubifs_zbranch *child = &new_zn->zbranch[i];
+
+			if (child->znode)
+				child->znode->parent = new_zn;
+		}
+	}
+
+	zbr->znode = new_zn;
+	zbr->lnum = 0;
+	zbr->offs = 0;
+	zbr->len = 0;
+
+	atomic_long_inc(&c->dirty_zn_cnt);
+}
+
+/**
  * dirty_cow_znode - ensure a znode is not being committed.
  * @c: UBIFS file-system description object
  * @zbr: branch of znode to check
@@ -265,21 +291,32 @@
 		return zn;
 
 	if (zbr->len) {
-		err = insert_old_idx(c, zbr->lnum, zbr->offs);
-		if (unlikely(err))
-			return ERR_PTR(err);
+		struct ubifs_old_idx *old_idx;
+
+		old_idx = kmalloc(sizeof(struct ubifs_old_idx), GFP_NOFS);
+		if (unlikely(!old_idx)) {
+			err = -ENOMEM;
+			goto out;
+		}
+		old_idx->lnum = zbr->lnum;
+		old_idx->offs = zbr->offs;
+
 		err = add_idx_dirt(c, zbr->lnum, zbr->len);
-	} else
-		err = 0;
+		if (err) {
+			kfree(old_idx);
+			goto out;
+		}
 
-	zbr->znode = zn;
-	zbr->lnum = 0;
-	zbr->offs = 0;
-	zbr->len = 0;
+		do_insert_old_idx(c, old_idx);
+	}
+
+	replace_znode(c, zn, znode, zbr);
 
-	if (unlikely(err))
-		return ERR_PTR(err);
 	return zn;
+
+out:
+	kfree(zn);
+	return ERR_PTR(err);
 }
 
 /**
@@ -3053,6 +3090,21 @@
 		cnext = cnext->cnext;
 		if (ubifs_zn_obsolete(znode))
 			kfree(znode);
+		else if (!ubifs_zn_cow(znode)) {
+			/*
+			 * Don't forget to update clean znode count after
+			 * committing failed, because ubifs will check this
+			 * count while closing tnc. Non-obsolete znode could
+			 * be re-dirtied during committing process, so dirty
+			 * flag is untrustable. The flag 'COW_ZNODE' is set
+			 * for each dirty znode before committing, and it is
+			 * cleared as long as the znode become clean, so we
+			 * can statistic clean znode count according to this
+			 * flag.
+			 */
+			atomic_long_inc(&c->clean_zn_cnt);
+			atomic_long_inc(&ubifs_clean_zn_cnt);
+		}
 	} while (cnext && cnext != c->cnext);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/tnc_commit.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/tnc_commit.c
@@ -657,6 +657,8 @@
 		znode->alt = 0;
 		cnext = find_next_dirty(znode);
 		if (!cnext) {
+			ubifs_assert(c, !znode->parent);
+			znode->cparent = NULL;
 			znode->cnext = c->cnext;
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/ubifs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/ubifs.h
@@ -1594,8 +1594,13 @@
 	return crypto_memneq(expected, got, c->hmac_desc_len);
 }
 
+#ifdef CONFIG_UBIFS_FS_AUTHENTICATION
 void ubifs_bad_hash(const struct ubifs_info *c, const void *node,
 		    const u8 *hash, int lnum, int offs);
+#else
+static inline void ubifs_bad_hash(const struct ubifs_info *c, const void *node,
+				  const u8 *hash, int lnum, int offs) {};
+#endif
 
 int __ubifs_node_check_hash(const struct ubifs_info *c, const void *buf,
 			  const u8 *expected);
@@ -1997,7 +2002,7 @@
 
 /* dir.c */
 struct inode *ubifs_new_inode(struct ubifs_info *c, struct inode *dir,
-			      umode_t mode);
+			      umode_t mode, bool is_xattr);
 int ubifs_getattr(struct user_namespace *mnt_userns, const struct path *path, struct kstat *stat,
 		  u32 request_mask, unsigned int flags);
 int ubifs_check_dir_empty(struct inode *dir);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ubifs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ubifs/xattr.c
@@ -110,7 +110,7 @@
 	if (err)
 		return err;
 
-	inode = ubifs_new_inode(c, host, S_IFREG | S_IRWXUGO);
+	inode = ubifs_new_inode(c, host, S_IFREG | S_IRWXUGO, true);
 	if (IS_ERR(inode)) {
 		err = PTR_ERR(inode);
 		goto out_budg;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/balloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/balloc.c
@@ -22,6 +22,7 @@
 #include "udfdecl.h"
 
 #include <linux/bitops.h>
+#include <linux/overflow.h>
 
 #include "udf_i.h"
 #include "udf_sb.h"
@@ -36,18 +37,45 @@
 			     unsigned long bitmap_nr)
 {
 	struct buffer_head *bh = NULL;
-	int retval = 0;
+	int i;
+	int max_bits, off, count;
 	struct kernel_lb_addr loc;
 
 	loc.logicalBlockNum = bitmap->s_extPosition;
 	loc.partitionReferenceNum = UDF_SB(sb)->s_partition;
 
 	bh = udf_tread(sb, udf_get_lb_pblock(sb, &loc, block));
+	bitmap->s_block_bitmap[bitmap_nr] = bh;
 	if (!bh)
-		retval = -EIO;
+		return -EIO;
 
-	bitmap->s_block_bitmap[bitmap_nr] = bh;
-	return retval;
+	/* Check consistency of Space Bitmap buffer. */
+	max_bits = sb->s_blocksize * 8;
+	if (!bitmap_nr) {
+		off = sizeof(struct spaceBitmapDesc) << 3;
+		count = min(max_bits - off, bitmap->s_nr_groups);
+	} else {
+		/*
+		 * Rough check if bitmap number is too big to have any bitmap
+		 * blocks reserved.
+		 */
+		if (bitmap_nr >
+		    (bitmap->s_nr_groups >> (sb->s_blocksize_bits + 3)) + 2)
+			return 0;
+		off = 0;
+		count = bitmap->s_nr_groups - bitmap_nr * max_bits +
+				(sizeof(struct spaceBitmapDesc) << 3);
+		count = min(count, max_bits);
+	}
+
+	for (i = 0; i < count; i++)
+		if (udf_test_bit(i + off, bh->b_data)) {
+			bitmap->s_block_bitmap[bitmap_nr] =
+							ERR_PTR(-EFSCORRUPTED);
+			brelse(bh);
+			return -EFSCORRUPTED;
+		}
+	return 0;
 }
 
 static int __load_block_bitmap(struct super_block *sb,
@@ -62,8 +90,15 @@
 			  block_group, nr_groups);
 	}
 
-	if (bitmap->s_block_bitmap[block_group])
+	if (bitmap->s_block_bitmap[block_group]) {
+		/*
+		 * The bitmap failed verification in the past. No point in
+		 * trying again.
+		 */
+		if (IS_ERR(bitmap->s_block_bitmap[block_group]))
+			return PTR_ERR(bitmap->s_block_bitmap[block_group]);
 		return block_group;
+	}
 
 	retval = read_block_bitmap(sb, bitmap, block_group, block_group);
 	if (retval < 0)
@@ -110,7 +145,6 @@
 {
 	struct udf_sb_info *sbi = UDF_SB(sb);
 	struct buffer_head *bh = NULL;
-	struct udf_part_map *partmap;
 	unsigned long block;
 	unsigned long block_group;
 	unsigned long bit;
@@ -119,19 +153,9 @@
 	unsigned long overflow;
 
 	mutex_lock(&sbi->s_alloc_mutex);
-	partmap = &sbi->s_partmaps[bloc->partitionReferenceNum];
-	if (bloc->logicalBlockNum + count < count ||
-	    (bloc->logicalBlockNum + count) > partmap->s_partition_len) {
-		udf_debug("%u < %d || %u + %u > %u\n",
-			  bloc->logicalBlockNum, 0,
-			  bloc->logicalBlockNum, count,
-			  partmap->s_partition_len);
-		goto error_return;
-	}
-
+	/* We make sure this cannot overflow when mounting the filesystem */
 	block = bloc->logicalBlockNum + offset +
 		(sizeof(struct spaceBitmapDesc) << 3);
-
 	do {
 		overflow = 0;
 		block_group = block >> (sb->s_blocksize_bits + 3);
@@ -361,7 +385,6 @@
 				  uint32_t count)
 {
 	struct udf_sb_info *sbi = UDF_SB(sb);
-	struct udf_part_map *partmap;
 	uint32_t start, end;
 	uint32_t elen;
 	struct kernel_lb_addr eloc;
@@ -370,16 +393,6 @@
 	struct udf_inode_info *iinfo;
 
 	mutex_lock(&sbi->s_alloc_mutex);
-	partmap = &sbi->s_partmaps[bloc->partitionReferenceNum];
-	if (bloc->logicalBlockNum + count < count ||
-	    (bloc->logicalBlockNum + count) > partmap->s_partition_len) {
-		udf_debug("%u < %d || %u + %u > %u\n",
-			  bloc->logicalBlockNum, 0,
-			  bloc->logicalBlockNum, count,
-			  partmap->s_partition_len);
-		goto error_return;
-	}
-
 	iinfo = UDF_I(table);
 	udf_add_free_space(sb, sbi->s_partition, count);
 
@@ -654,6 +667,17 @@
 {
 	uint16_t partition = bloc->partitionReferenceNum;
 	struct udf_part_map *map = &UDF_SB(sb)->s_partmaps[partition];
+	uint32_t blk;
+
+	if (check_add_overflow(bloc->logicalBlockNum, offset, &blk) ||
+	    check_add_overflow(blk, count, &blk) ||
+	    bloc->logicalBlockNum + count > map->s_partition_len) {
+		udf_debug("Invalid request to free blocks: (%d, %u), off %u, "
+			  "len %u, partition len %u\n",
+			  partition, bloc->logicalBlockNum, offset, count,
+			  map->s_partition_len);
+		return;
+	}
 
 	if (map->s_partition_flags & UDF_PART_FLAG_UNALLOC_BITMAP) {
 		udf_bitmap_free_blocks(sb, map->s_uspace.s_bitmap,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/dir.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/dir.c
@@ -31,6 +31,7 @@
 #include <linux/mm.h>
 #include <linux/slab.h>
 #include <linux/bio.h>
+#include <linux/iversion.h>
 
 #include "udf_i.h"
 #include "udf_sb.h"
@@ -38,25 +39,13 @@
 static int udf_readdir(struct file *file, struct dir_context *ctx)
 {
 	struct inode *dir = file_inode(file);
-	struct udf_inode_info *iinfo = UDF_I(dir);
-	struct udf_fileident_bh fibh = { .sbh = NULL, .ebh = NULL};
-	struct fileIdentDesc *fi = NULL;
-	struct fileIdentDesc cfi;
-	udf_pblk_t block, iblock;
-	loff_t nf_pos;
+	loff_t nf_pos, emit_pos = 0;
 	int flen;
-	unsigned char *fname = NULL, *copy_name = NULL;
-	unsigned char *nameptr;
-	uint16_t liu;
-	uint8_t lfi;
-	loff_t size = udf_ext0_offset(dir) + dir->i_size;
-	struct buffer_head *tmp, *bha[16];
-	struct kernel_lb_addr eloc;
-	uint32_t elen;
-	sector_t offset;
-	int i, num, ret = 0;
-	struct extent_position epos = { NULL, 0, {0, 0} };
+	unsigned char *fname = NULL;
+	int ret = 0;
 	struct super_block *sb = dir->i_sb;
+	bool pos_valid = false;
+	struct udf_fileident_iter iter;
 
 	if (ctx->pos == 0) {
 		if (!dir_emit_dot(file, ctx))
@@ -64,136 +53,81 @@
 		ctx->pos = 1;
 	}
 	nf_pos = (ctx->pos - 1) << 2;
-	if (nf_pos >= size)
+	if (nf_pos >= dir->i_size)
 		goto out;
 
+	/*
+	 * Something changed since last readdir (either lseek was called or dir
+	 * changed)?  We need to verify the position correctly points at the
+	 * beginning of some dir entry so that the directory parsing code does
+	 * not get confused. Since UDF does not have any reliable way of
+	 * identifying beginning of dir entry (names are under user control),
+	 * we need to scan the directory from the beginning.
+	 */
+	if (!inode_eq_iversion(dir, file->f_version)) {
+		emit_pos = nf_pos;
+		nf_pos = 0;
+	} else {
+		pos_valid = true;
+	}
+
 	fname = kmalloc(UDF_NAME_LEN, GFP_NOFS);
 	if (!fname) {
 		ret = -ENOMEM;
 		goto out;
 	}
 
-	if (nf_pos == 0)
-		nf_pos = udf_ext0_offset(dir);
-
-	fibh.soffset = fibh.eoffset = nf_pos & (sb->s_blocksize - 1);
-	if (iinfo->i_alloc_type != ICBTAG_FLAG_AD_IN_ICB) {
-		if (inode_bmap(dir, nf_pos >> sb->s_blocksize_bits,
-		    &epos, &eloc, &elen, &offset)
-		    != (EXT_RECORDED_ALLOCATED >> 30)) {
-			ret = -ENOENT;
-			goto out;
-		}
-		block = udf_get_lb_pblock(sb, &eloc, offset);
-		if ((++offset << sb->s_blocksize_bits) < elen) {
-			if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-				epos.offset -= sizeof(struct short_ad);
-			else if (iinfo->i_alloc_type ==
-					ICBTAG_FLAG_AD_LONG)
-				epos.offset -= sizeof(struct long_ad);
-		} else {
-			offset = 0;
-		}
-
-		if (!(fibh.sbh = fibh.ebh = udf_tread(sb, block))) {
-			ret = -EIO;
-			goto out;
-		}
-
-		if (!(offset & ((16 >> (sb->s_blocksize_bits - 9)) - 1))) {
-			i = 16 >> (sb->s_blocksize_bits - 9);
-			if (i + offset > (elen >> sb->s_blocksize_bits))
-				i = (elen >> sb->s_blocksize_bits) - offset;
-			for (num = 0; i > 0; i--) {
-				block = udf_get_lb_pblock(sb, &eloc, offset + i);
-				tmp = udf_tgetblk(sb, block);
-				if (tmp && !buffer_uptodate(tmp) && !buffer_locked(tmp))
-					bha[num++] = tmp;
-				else
-					brelse(tmp);
-			}
-			if (num) {
-				ll_rw_block(REQ_OP_READ, REQ_RAHEAD, num, bha);
-				for (i = 0; i < num; i++)
-					brelse(bha[i]);
-			}
-		}
-	}
-
-	while (nf_pos < size) {
+	for (ret = udf_fiiter_init(&iter, dir, nf_pos);
+	     !ret && iter.pos < dir->i_size;
+	     ret = udf_fiiter_advance(&iter)) {
 		struct kernel_lb_addr tloc;
+		udf_pblk_t iblock;
 
-		ctx->pos = (nf_pos >> 2) + 1;
+		/* Still not at offset where user asked us to read from? */
+		if (iter.pos < emit_pos)
+			continue;
 
-		fi = udf_fileident_read(dir, &nf_pos, &fibh, &cfi, &epos, &eloc,
-					&elen, &offset);
-		if (!fi)
-			goto out;
-
-		liu = le16_to_cpu(cfi.lengthOfImpUse);
-		lfi = cfi.lengthFileIdent;
-
-		if (fibh.sbh == fibh.ebh) {
-			nameptr = udf_get_fi_ident(fi);
-		} else {
-			int poffset;	/* Unpaded ending offset */
-
-			poffset = fibh.soffset + sizeof(struct fileIdentDesc) + liu + lfi;
-
-			if (poffset >= lfi) {
-				nameptr = (char *)(fibh.ebh->b_data + poffset - lfi);
-			} else {
-				if (!copy_name) {
-					copy_name = kmalloc(UDF_NAME_LEN,
-							    GFP_NOFS);
-					if (!copy_name) {
-						ret = -ENOMEM;
-						goto out;
-					}
-				}
-				nameptr = copy_name;
-				memcpy(nameptr, udf_get_fi_ident(fi),
-				       lfi - poffset);
-				memcpy(nameptr + lfi - poffset,
-				       fibh.ebh->b_data, poffset);
-			}
-		}
+		/* Update file position only if we got past the current one */
+		pos_valid = true;
+		ctx->pos = (iter.pos >> 2) + 1;
 
-		if ((cfi.fileCharacteristics & FID_FILE_CHAR_DELETED) != 0) {
+		if (iter.fi.fileCharacteristics & FID_FILE_CHAR_DELETED) {
 			if (!UDF_QUERY_FLAG(sb, UDF_FLAG_UNDELETE))
 				continue;
 		}
 
-		if ((cfi.fileCharacteristics & FID_FILE_CHAR_HIDDEN) != 0) {
+		if (iter.fi.fileCharacteristics & FID_FILE_CHAR_HIDDEN) {
 			if (!UDF_QUERY_FLAG(sb, UDF_FLAG_UNHIDE))
 				continue;
 		}
 
-		if (cfi.fileCharacteristics & FID_FILE_CHAR_PARENT) {
+		if (iter.fi.fileCharacteristics & FID_FILE_CHAR_PARENT) {
 			if (!dir_emit_dotdot(file, ctx))
-				goto out;
+				goto out_iter;
 			continue;
 		}
 
-		flen = udf_get_filename(sb, nameptr, lfi, fname, UDF_NAME_LEN);
+		flen = udf_get_filename(sb, iter.name,
+				iter.fi.lengthFileIdent, fname, UDF_NAME_LEN);
 		if (flen < 0)
 			continue;
 
-		tloc = lelb_to_cpu(cfi.icb.extLocation);
+		tloc = lelb_to_cpu(iter.fi.icb.extLocation);
 		iblock = udf_get_lb_pblock(sb, &tloc, 0);
 		if (!dir_emit(ctx, fname, flen, iblock, DT_UNKNOWN))
-			goto out;
-	} /* end while */
-
-	ctx->pos = (nf_pos >> 2) + 1;
+			goto out_iter;
+	}
 
+	if (!ret) {
+		ctx->pos = (iter.pos >> 2) + 1;
+		pos_valid = true;
+	}
+out_iter:
+	udf_fiiter_release(&iter);
 out:
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
-	brelse(epos.bh);
+	if (pos_valid)
+		file->f_version = inode_query_iversion(dir);
 	kfree(fname);
-	kfree(copy_name);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/directory.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/directory.c
@@ -17,183 +17,468 @@
 #include <linux/fs.h>
 #include <linux/string.h>
 #include <linux/bio.h>
+#include <linux/crc-itu-t.h>
+#include <linux/iversion.h>
+#include <linux/slab.h>
 
-struct fileIdentDesc *udf_fileident_read(struct inode *dir, loff_t *nf_pos,
-					 struct udf_fileident_bh *fibh,
-					 struct fileIdentDesc *cfi,
-					 struct extent_position *epos,
-					 struct kernel_lb_addr *eloc, uint32_t *elen,
-					 sector_t *offset)
+static int udf_verify_fi(struct udf_fileident_iter *iter)
 {
-	struct fileIdentDesc *fi;
-	int i, num;
-	udf_pblk_t block;
-	struct buffer_head *tmp, *bha[16];
-	struct udf_inode_info *iinfo = UDF_I(dir);
+	unsigned int len;
 
-	fibh->soffset = fibh->eoffset;
+	if (iter->fi.descTag.tagIdent != cpu_to_le16(TAG_IDENT_FID)) {
+		udf_err(iter->dir->i_sb,
+			"directory (ino %lu) has entry at pos %llu with incorrect tag %x\n",
+			iter->dir->i_ino, (unsigned long long)iter->pos,
+			le16_to_cpu(iter->fi.descTag.tagIdent));
+		return -EFSCORRUPTED;
+	}
+	len = udf_dir_entry_len(&iter->fi);
+	if (le16_to_cpu(iter->fi.lengthOfImpUse) & 3) {
+		udf_err(iter->dir->i_sb,
+			"directory (ino %lu) has entry at pos %llu with unaligned lenght of impUse field\n",
+			iter->dir->i_ino, (unsigned long long)iter->pos);
+		return -EFSCORRUPTED;
+	}
+	/*
+	 * This is in fact allowed by the spec due to long impUse field but
+	 * we don't support it. If there is real media with this large impUse
+	 * field, support can be added.
+	 */
+	if (len > 1 << iter->dir->i_blkbits) {
+		udf_err(iter->dir->i_sb,
+			"directory (ino %lu) has too big (%u) entry at pos %llu\n",
+			iter->dir->i_ino, len, (unsigned long long)iter->pos);
+		return -EFSCORRUPTED;
+	}
+	if (iter->pos + len > iter->dir->i_size) {
+		udf_err(iter->dir->i_sb,
+			"directory (ino %lu) has entry past directory size at pos %llu\n",
+			iter->dir->i_ino, (unsigned long long)iter->pos);
+		return -EFSCORRUPTED;
+	}
+	if (udf_dir_entry_len(&iter->fi) !=
+	    sizeof(struct tag) + le16_to_cpu(iter->fi.descTag.descCRCLength)) {
+		udf_err(iter->dir->i_sb,
+			"directory (ino %lu) has entry where CRC length (%u) does not match entry length (%u)\n",
+			iter->dir->i_ino,
+			(unsigned)le16_to_cpu(iter->fi.descTag.descCRCLength),
+			(unsigned)(udf_dir_entry_len(&iter->fi) -
+							sizeof(struct tag)));
+		return -EFSCORRUPTED;
+	}
+	return 0;
+}
 
+static int udf_copy_fi(struct udf_fileident_iter *iter)
+{
+	struct udf_inode_info *iinfo = UDF_I(iter->dir);
+	int blksize = 1 << iter->dir->i_blkbits;
+	int err, off, len, nameoff;
+
+	/* Skip copying when we are at EOF */
+	if (iter->pos >= iter->dir->i_size) {
+		iter->name = NULL;
+		return 0;
+	}
+	if (iter->dir->i_size < iter->pos + sizeof(struct fileIdentDesc)) {
+		udf_err(iter->dir->i_sb,
+			"directory (ino %lu) has entry straddling EOF\n",
+			iter->dir->i_ino);
+		return -EFSCORRUPTED;
+	}
 	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
-		fi = udf_get_fileident(iinfo->i_data -
-				       (iinfo->i_efe ?
-					sizeof(struct extendedFileEntry) :
-					sizeof(struct fileEntry)),
-				       dir->i_sb->s_blocksize,
-				       &(fibh->eoffset));
-		if (!fi)
-			return NULL;
-
-		*nf_pos += fibh->eoffset - fibh->soffset;
-
-		memcpy((uint8_t *)cfi, (uint8_t *)fi,
+		memcpy(&iter->fi, iinfo->i_data + iinfo->i_lenEAttr + iter->pos,
 		       sizeof(struct fileIdentDesc));
+		err = udf_verify_fi(iter);
+		if (err < 0)
+			return err;
+		iter->name = iinfo->i_data + iinfo->i_lenEAttr + iter->pos +
+			sizeof(struct fileIdentDesc) +
+			le16_to_cpu(iter->fi.lengthOfImpUse);
+		return 0;
+	}
 
-		return fi;
+	off = iter->pos & (blksize - 1);
+	len = min_t(int, sizeof(struct fileIdentDesc), blksize - off);
+	memcpy(&iter->fi, iter->bh[0]->b_data + off, len);
+	if (len < sizeof(struct fileIdentDesc))
+		memcpy((char *)(&iter->fi) + len, iter->bh[1]->b_data,
+		       sizeof(struct fileIdentDesc) - len);
+	err = udf_verify_fi(iter);
+	if (err < 0)
+		return err;
+
+	/* Handle directory entry name */
+	nameoff = off + sizeof(struct fileIdentDesc) +
+				le16_to_cpu(iter->fi.lengthOfImpUse);
+	if (off + udf_dir_entry_len(&iter->fi) <= blksize) {
+		iter->name = iter->bh[0]->b_data + nameoff;
+	} else if (nameoff >= blksize) {
+		iter->name = iter->bh[1]->b_data + (nameoff - blksize);
+	} else {
+		iter->name = iter->namebuf;
+		len = blksize - nameoff;
+		memcpy(iter->name, iter->bh[0]->b_data + nameoff, len);
+		memcpy(iter->name + len, iter->bh[1]->b_data,
+		       iter->fi.lengthFileIdent - len);
 	}
+	return 0;
+}
 
-	if (fibh->eoffset == dir->i_sb->s_blocksize) {
-		uint32_t lextoffset = epos->offset;
-		unsigned char blocksize_bits = dir->i_sb->s_blocksize_bits;
+/* Readahead 8k once we are at 8k boundary */
+static void udf_readahead_dir(struct udf_fileident_iter *iter)
+{
+	unsigned int ralen = 16 >> (iter->dir->i_blkbits - 9);
+	struct buffer_head *tmp, *bha[16];
+	int i, num;
+	udf_pblk_t blk;
 
-		if (udf_next_aext(dir, epos, eloc, elen, 1) !=
-		    (EXT_RECORDED_ALLOCATED >> 30))
-			return NULL;
+	if (iter->loffset & (ralen - 1))
+		return;
 
-		block = udf_get_lb_pblock(dir->i_sb, eloc, *offset);
+	if (iter->loffset + ralen > (iter->elen >> iter->dir->i_blkbits))
+		ralen = (iter->elen >> iter->dir->i_blkbits) - iter->loffset;
+	num = 0;
+	for (i = 0; i < ralen; i++) {
+		blk = udf_get_lb_pblock(iter->dir->i_sb, &iter->eloc,
+					iter->loffset + i);
+		tmp = udf_tgetblk(iter->dir->i_sb, blk);
+		if (tmp && !buffer_uptodate(tmp) && !buffer_locked(tmp))
+			bha[num++] = tmp;
+		else
+			brelse(tmp);
+	}
+	if (num) {
+		ll_rw_block(REQ_OP_READ, REQ_RAHEAD, num, bha);
+		for (i = 0; i < num; i++)
+			brelse(bha[i]);
+	}
+}
 
-		(*offset)++;
+static struct buffer_head *udf_fiiter_bread_blk(struct udf_fileident_iter *iter)
+{
+	udf_pblk_t blk;
 
-		if ((*offset << blocksize_bits) >= *elen)
-			*offset = 0;
-		else
-			epos->offset = lextoffset;
+	udf_readahead_dir(iter);
+	blk = udf_get_lb_pblock(iter->dir->i_sb, &iter->eloc, iter->loffset);
+	return udf_tread(iter->dir->i_sb, blk);
+}
 
-		brelse(fibh->sbh);
-		fibh->sbh = fibh->ebh = udf_tread(dir->i_sb, block);
-		if (!fibh->sbh)
-			return NULL;
-		fibh->soffset = fibh->eoffset = 0;
-
-		if (!(*offset & ((16 >> (blocksize_bits - 9)) - 1))) {
-			i = 16 >> (blocksize_bits - 9);
-			if (i + *offset > (*elen >> blocksize_bits))
-				i = (*elen >> blocksize_bits)-*offset;
-			for (num = 0; i > 0; i--) {
-				block = udf_get_lb_pblock(dir->i_sb, eloc,
-							  *offset + i);
-				tmp = udf_tgetblk(dir->i_sb, block);
-				if (tmp && !buffer_uptodate(tmp) &&
-						!buffer_locked(tmp))
-					bha[num++] = tmp;
-				else
-					brelse(tmp);
-			}
-			if (num) {
-				ll_rw_block(REQ_OP_READ, REQ_RAHEAD, num, bha);
-				for (i = 0; i < num; i++)
-					brelse(bha[i]);
-			}
+/*
+ * Updates loffset to point to next directory block; eloc, elen & epos are
+ * updated if we need to traverse to the next extent as well.
+ */
+static int udf_fiiter_advance_blk(struct udf_fileident_iter *iter)
+{
+	iter->loffset++;
+	if (iter->loffset < DIV_ROUND_UP(iter->elen, 1<<iter->dir->i_blkbits))
+		return 0;
+
+	iter->loffset = 0;
+	if (udf_next_aext(iter->dir, &iter->epos, &iter->eloc, &iter->elen, 1)
+			!= (EXT_RECORDED_ALLOCATED >> 30)) {
+		if (iter->pos == iter->dir->i_size) {
+			iter->elen = 0;
+			return 0;
 		}
-	} else if (fibh->sbh != fibh->ebh) {
-		brelse(fibh->sbh);
-		fibh->sbh = fibh->ebh;
+		udf_err(iter->dir->i_sb,
+			"extent after position %llu not allocated in directory (ino %lu)\n",
+			(unsigned long long)iter->pos, iter->dir->i_ino);
+		return -EFSCORRUPTED;
 	}
+	return 0;
+}
 
-	fi = udf_get_fileident(fibh->sbh->b_data, dir->i_sb->s_blocksize,
-			       &(fibh->eoffset));
+static int udf_fiiter_load_bhs(struct udf_fileident_iter *iter)
+{
+	int blksize = 1 << iter->dir->i_blkbits;
+	int off = iter->pos & (blksize - 1);
+	int err;
+	struct fileIdentDesc *fi;
 
-	if (!fi)
-		return NULL;
+	/* Is there any further extent we can map from? */
+	if (!iter->bh[0] && iter->elen) {
+		iter->bh[0] = udf_fiiter_bread_blk(iter);
+		if (!iter->bh[0]) {
+			err = -ENOMEM;
+			goto out_brelse;
+		}
+		if (!buffer_uptodate(iter->bh[0])) {
+			err = -EIO;
+			goto out_brelse;
+		}
+	}
+	/* There's no next block so we are done */
+	if (iter->pos >= iter->dir->i_size)
+		return 0;
+	/* Need to fetch next block as well? */
+	if (off + sizeof(struct fileIdentDesc) > blksize)
+		goto fetch_next;
+	fi = (struct fileIdentDesc *)(iter->bh[0]->b_data + off);
+	/* Need to fetch next block to get name? */
+	if (off + udf_dir_entry_len(fi) > blksize) {
+fetch_next:
+		udf_fiiter_advance_blk(iter);
+		iter->bh[1] = udf_fiiter_bread_blk(iter);
+		if (!iter->bh[1]) {
+			err = -ENOMEM;
+			goto out_brelse;
+		}
+		if (!buffer_uptodate(iter->bh[1])) {
+			err = -EIO;
+			goto out_brelse;
+		}
+	}
+	return 0;
+out_brelse:
+	brelse(iter->bh[0]);
+	brelse(iter->bh[1]);
+	iter->bh[0] = iter->bh[1] = NULL;
+	return err;
+}
 
-	*nf_pos += fibh->eoffset - fibh->soffset;
+int udf_fiiter_init(struct udf_fileident_iter *iter, struct inode *dir,
+		    loff_t pos)
+{
+	struct udf_inode_info *iinfo = UDF_I(dir);
+	int err = 0;
 
-	if (fibh->eoffset <= dir->i_sb->s_blocksize) {
-		memcpy((uint8_t *)cfi, (uint8_t *)fi,
-		       sizeof(struct fileIdentDesc));
-	} else if (fibh->eoffset > dir->i_sb->s_blocksize) {
-		uint32_t lextoffset = epos->offset;
+	iter->dir = dir;
+	iter->bh[0] = iter->bh[1] = NULL;
+	iter->pos = pos;
+	iter->elen = 0;
+	iter->epos.bh = NULL;
+	iter->name = NULL;
+	/*
+	 * When directory is verified, we don't expect directory iteration to
+	 * fail and it can be difficult to undo without corrupting filesystem.
+	 * So just do not allow memory allocation failures here.
+	 */
+	iter->namebuf = kmalloc(UDF_NAME_LEN_CS0, GFP_KERNEL | __GFP_NOFAIL);
+
+	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
+		err = udf_copy_fi(iter);
+		goto out;
+	}
 
-		if (udf_next_aext(dir, epos, eloc, elen, 1) !=
-		    (EXT_RECORDED_ALLOCATED >> 30))
-			return NULL;
+	if (inode_bmap(dir, iter->pos >> dir->i_blkbits, &iter->epos,
+		       &iter->eloc, &iter->elen, &iter->loffset) !=
+	    (EXT_RECORDED_ALLOCATED >> 30)) {
+		if (pos == dir->i_size)
+			return 0;
+		udf_err(dir->i_sb,
+			"position %llu not allocated in directory (ino %lu)\n",
+			(unsigned long long)pos, dir->i_ino);
+		err = -EFSCORRUPTED;
+		goto out;
+	}
+	err = udf_fiiter_load_bhs(iter);
+	if (err < 0)
+		goto out;
+	err = udf_copy_fi(iter);
+out:
+	if (err < 0)
+		udf_fiiter_release(iter);
+	return err;
+}
+
+int udf_fiiter_advance(struct udf_fileident_iter *iter)
+{
+	unsigned int oldoff, len;
+	int blksize = 1 << iter->dir->i_blkbits;
+	int err;
+
+	oldoff = iter->pos & (blksize - 1);
+	len = udf_dir_entry_len(&iter->fi);
+	iter->pos += len;
+	if (UDF_I(iter->dir)->i_alloc_type != ICBTAG_FLAG_AD_IN_ICB) {
+		if (oldoff + len >= blksize) {
+			brelse(iter->bh[0]);
+			iter->bh[0] = NULL;
+			/* Next block already loaded? */
+			if (iter->bh[1]) {
+				iter->bh[0] = iter->bh[1];
+				iter->bh[1] = NULL;
+			} else {
+				udf_fiiter_advance_blk(iter);
+			}
+		}
+		err = udf_fiiter_load_bhs(iter);
+		if (err < 0)
+			return err;
+	}
+	return udf_copy_fi(iter);
+}
 
-		block = udf_get_lb_pblock(dir->i_sb, eloc, *offset);
+void udf_fiiter_release(struct udf_fileident_iter *iter)
+{
+	iter->dir = NULL;
+	brelse(iter->bh[0]);
+	brelse(iter->bh[1]);
+	iter->bh[0] = iter->bh[1] = NULL;
+	kfree(iter->namebuf);
+	iter->namebuf = NULL;
+}
 
-		(*offset)++;
+static void udf_copy_to_bufs(void *buf1, int len1, void *buf2, int len2,
+			     int off, void *src, int len)
+{
+	int copy;
 
-		if ((*offset << dir->i_sb->s_blocksize_bits) >= *elen)
-			*offset = 0;
-		else
-			epos->offset = lextoffset;
+	if (off >= len1) {
+		off -= len1;
+	} else {
+		copy = min(off + len, len1) - off;
+		memcpy(buf1 + off, src, copy);
+		src += copy;
+		len -= copy;
+		off = 0;
+	}
+	if (len > 0) {
+		if (WARN_ON_ONCE(off + len > len2 || !buf2))
+			return;
+		memcpy(buf2 + off, src, len);
+	}
+}
 
-		fibh->soffset -= dir->i_sb->s_blocksize;
-		fibh->eoffset -= dir->i_sb->s_blocksize;
+static uint16_t udf_crc_fi_bufs(void *buf1, int len1, void *buf2, int len2,
+				int off, int len)
+{
+	int copy;
+	uint16_t crc = 0;
+
+	if (off >= len1) {
+		off -= len1;
+	} else {
+		copy = min(off + len, len1) - off;
+		crc = crc_itu_t(crc, buf1 + off, copy);
+		len -= copy;
+		off = 0;
+	}
+	if (len > 0) {
+		if (WARN_ON_ONCE(off + len > len2 || !buf2))
+			return 0;
+		crc = crc_itu_t(crc, buf2 + off, len);
+	}
+	return crc;
+}
 
-		fibh->ebh = udf_tread(dir->i_sb, block);
-		if (!fibh->ebh)
-			return NULL;
+static void udf_copy_fi_to_bufs(char *buf1, int len1, char *buf2, int len2,
+				int off, struct fileIdentDesc *fi,
+				uint8_t *impuse, uint8_t *name)
+{
+	uint16_t crc;
+	int fioff = off;
+	int crcoff = off + sizeof(struct tag);
+	unsigned int crclen = udf_dir_entry_len(fi) - sizeof(struct tag);
+
+	udf_copy_to_bufs(buf1, len1, buf2, len2, off, fi,
+			 sizeof(struct fileIdentDesc));
+	off += sizeof(struct fileIdentDesc);
+	if (impuse)
+		udf_copy_to_bufs(buf1, len1, buf2, len2, off, impuse,
+				 le16_to_cpu(fi->lengthOfImpUse));
+	off += le16_to_cpu(fi->lengthOfImpUse);
+	if (name)
+		udf_copy_to_bufs(buf1, len1, buf2, len2, off, name,
+				 fi->lengthFileIdent);
+
+	crc = udf_crc_fi_bufs(buf1, len1, buf2, len2, crcoff, crclen);
+	fi->descTag.descCRC = cpu_to_le16(crc);
+	fi->descTag.descCRCLength = cpu_to_le16(crclen);
+	fi->descTag.tagChecksum = udf_tag_checksum(&fi->descTag);
 
-		if (sizeof(struct fileIdentDesc) > -fibh->soffset) {
-			int fi_len;
+	udf_copy_to_bufs(buf1, len1, buf2, len2, fioff, fi, sizeof(struct tag));
+}
 
-			memcpy((uint8_t *)cfi, (uint8_t *)fi, -fibh->soffset);
-			memcpy((uint8_t *)cfi - fibh->soffset,
-			       fibh->ebh->b_data,
-			       sizeof(struct fileIdentDesc) + fibh->soffset);
+void udf_fiiter_write_fi(struct udf_fileident_iter *iter, uint8_t *impuse)
+{
+	struct udf_inode_info *iinfo = UDF_I(iter->dir);
+	void *buf1, *buf2 = NULL;
+	int len1, len2 = 0, off;
+	int blksize = 1 << iter->dir->i_blkbits;
 
-			fi_len = udf_dir_entry_len(cfi);
-			*nf_pos += fi_len - (fibh->eoffset - fibh->soffset);
-			fibh->eoffset = fibh->soffset + fi_len;
-		} else {
-			memcpy((uint8_t *)cfi, (uint8_t *)fi,
-			       sizeof(struct fileIdentDesc));
+	off = iter->pos & (blksize - 1);
+	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
+		buf1 = iinfo->i_data + iinfo->i_lenEAttr;
+		len1 = iter->dir->i_size;
+	} else {
+		buf1 = iter->bh[0]->b_data;
+		len1 = blksize;
+		if (iter->bh[1]) {
+			buf2 = iter->bh[1]->b_data;
+			len2 = blksize;
 		}
 	}
-	/* Got last entry outside of dir size - fs is corrupted! */
-	if (*nf_pos > dir->i_size)
-		return NULL;
-	return fi;
+
+	udf_copy_fi_to_bufs(buf1, len1, buf2, len2, off, &iter->fi, impuse,
+			    iter->name == iter->namebuf ? iter->name : NULL);
+
+	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
+		mark_inode_dirty(iter->dir);
+	} else {
+		mark_buffer_dirty_inode(iter->bh[0], iter->dir);
+		if (iter->bh[1])
+			mark_buffer_dirty_inode(iter->bh[1], iter->dir);
+	}
+	inode_inc_iversion(iter->dir);
 }
 
-struct fileIdentDesc *udf_get_fileident(void *buffer, int bufsize, int *offset)
+void udf_fiiter_update_elen(struct udf_fileident_iter *iter, uint32_t new_elen)
 {
-	struct fileIdentDesc *fi;
-	int lengthThisIdent;
-	uint8_t *ptr;
-	int padlen;
-
-	if ((!buffer) || (!offset)) {
-		udf_debug("invalidparms, buffer=%p, offset=%p\n",
-			  buffer, offset);
-		return NULL;
-	}
-
-	ptr = buffer;
-
-	if ((*offset > 0) && (*offset < bufsize))
-		ptr += *offset;
-	fi = (struct fileIdentDesc *)ptr;
-	if (fi->descTag.tagIdent != cpu_to_le16(TAG_IDENT_FID)) {
-		udf_debug("0x%x != TAG_IDENT_FID\n",
-			  le16_to_cpu(fi->descTag.tagIdent));
-		udf_debug("offset: %d sizeof: %lu bufsize: %d\n",
-			  *offset, (unsigned long)sizeof(struct fileIdentDesc),
-			  bufsize);
-		return NULL;
-	}
-	if ((*offset + sizeof(struct fileIdentDesc)) > bufsize)
-		lengthThisIdent = sizeof(struct fileIdentDesc);
-	else
-		lengthThisIdent = sizeof(struct fileIdentDesc) +
-			fi->lengthFileIdent + le16_to_cpu(fi->lengthOfImpUse);
-
-	/* we need to figure padding, too! */
-	padlen = lengthThisIdent % UDF_NAME_PAD;
-	if (padlen)
-		lengthThisIdent += (UDF_NAME_PAD - padlen);
-	*offset = *offset + lengthThisIdent;
+	struct udf_inode_info *iinfo = UDF_I(iter->dir);
+	int diff = new_elen - iter->elen;
+
+	/* Skip update when we already went past the last extent */
+	if (!iter->elen)
+		return;
+	iter->elen = new_elen;
+	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
+		iter->epos.offset -= sizeof(struct short_ad);
+	else if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
+		iter->epos.offset -= sizeof(struct long_ad);
+	udf_write_aext(iter->dir, &iter->epos, &iter->eloc, iter->elen, 1);
+	iinfo->i_lenExtents += diff;
+	mark_inode_dirty(iter->dir);
+}
 
-	return fi;
+/* Append new block to directory. @iter is expected to point at EOF */
+int udf_fiiter_append_blk(struct udf_fileident_iter *iter)
+{
+	struct udf_inode_info *iinfo = UDF_I(iter->dir);
+	int blksize = 1 << iter->dir->i_blkbits;
+	struct buffer_head *bh;
+	sector_t block;
+	uint32_t old_elen = iter->elen;
+	int err;
+
+	if (WARN_ON_ONCE(iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB))
+		return -EINVAL;
+
+	/* Round up last extent in the file */
+	udf_fiiter_update_elen(iter, ALIGN(iter->elen, blksize));
+
+	/* Allocate new block and refresh mapping information */
+	block = iinfo->i_lenExtents >> iter->dir->i_blkbits;
+	bh = udf_bread(iter->dir, block, 1, &err);
+	if (!bh) {
+		udf_fiiter_update_elen(iter, old_elen);
+		return err;
+	}
+	if (inode_bmap(iter->dir, block, &iter->epos, &iter->eloc, &iter->elen,
+		       &iter->loffset) != (EXT_RECORDED_ALLOCATED >> 30)) {
+		udf_err(iter->dir->i_sb,
+			"block %llu not allocated in directory (ino %lu)\n",
+			(unsigned long long)block, iter->dir->i_ino);
+		return -EFSCORRUPTED;
+	}
+	if (!(iter->pos & (blksize - 1))) {
+		brelse(iter->bh[0]);
+		iter->bh[0] = bh;
+	} else {
+		iter->bh[1] = bh;
+	}
+	return 0;
 }
 
 struct short_ad *udf_get_fileshortad(uint8_t *ptr, int maxoffset, uint32_t *offset,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/file.c
@@ -148,26 +148,24 @@
 		goto out;
 
 	down_write(&iinfo->i_data_sem);
-	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
-		loff_t end = iocb->ki_pos + iov_iter_count(from);
-
-		if (inode->i_sb->s_blocksize <
-				(udf_file_entry_alloc_offset(inode) + end)) {
-			err = udf_expand_file_adinicb(inode);
-			if (err) {
-				inode_unlock(inode);
-				udf_debug("udf_expand_adinicb: err=%d\n", err);
-				return err;
-			}
-		} else {
-			iinfo->i_lenAlloc = max(end, inode->i_size);
-			up_write(&iinfo->i_data_sem);
+	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB &&
+	    inode->i_sb->s_blocksize < (udf_file_entry_alloc_offset(inode) +
+				 iocb->ki_pos + iov_iter_count(from))) {
+		err = udf_expand_file_adinicb(inode);
+		if (err) {
+			inode_unlock(inode);
+			udf_debug("udf_expand_adinicb: err=%d\n", err);
+			return err;
 		}
 	} else
 		up_write(&iinfo->i_data_sem);
 
 	retval = __generic_file_write_iter(iocb, from);
 out:
+	down_write(&iinfo->i_data_sem);
+	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB && retval > 0)
+		iinfo->i_lenAlloc = inode->i_size;
+	up_write(&iinfo->i_data_sem);
 	inode_unlock(inode);
 
 	if (retval > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/ialloc.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/ialloc.c
@@ -77,6 +77,7 @@
 					GFP_KERNEL);
 	}
 	if (!iinfo->i_data) {
+		make_bad_inode(inode);
 		iput(inode);
 		return ERR_PTR(-ENOMEM);
 	}
@@ -86,6 +87,7 @@
 			      dinfo->i_location.partitionReferenceNum,
 			      start, &err);
 	if (err) {
+		make_bad_inode(inode);
 		iput(inode);
 		return ERR_PTR(err);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/inode.c
@@ -57,15 +57,15 @@
 static int udf_sync_inode(struct inode *inode);
 static int udf_alloc_i_data(struct inode *inode, size_t size);
 static sector_t inode_getblk(struct inode *, sector_t, int *, int *);
-static int8_t udf_insert_aext(struct inode *, struct extent_position,
-			      struct kernel_lb_addr, uint32_t);
+static int udf_insert_aext(struct inode *, struct extent_position,
+			   struct kernel_lb_addr, uint32_t);
 static void udf_split_extents(struct inode *, int *, int, udf_pblk_t,
 			      struct kernel_long_ad *, int *);
 static void udf_prealloc_extents(struct inode *, int, int,
 				 struct kernel_long_ad *, int *);
 static void udf_merge_extents(struct inode *, struct kernel_long_ad *, int *);
-static void udf_update_extents(struct inode *, struct kernel_long_ad *, int,
-			       int, struct extent_position *);
+static int udf_update_extents(struct inode *, struct kernel_long_ad *, int,
+			      int, struct extent_position *);
 static int udf_get_block(struct inode *, sector_t, struct buffer_head *, int);
 
 static void __udf_clear_extent_cache(struct inode *inode)
@@ -258,10 +258,6 @@
 	char *kaddr;
 	struct udf_inode_info *iinfo = UDF_I(inode);
 	int err;
-	struct writeback_control udf_wbc = {
-		.sync_mode = WB_SYNC_NONE,
-		.nr_to_write = 1,
-	};
 
 	WARN_ON_ONCE(!inode_is_locked(inode));
 	if (!iinfo->i_lenAlloc) {
@@ -305,8 +301,10 @@
 		iinfo->i_alloc_type = ICBTAG_FLAG_AD_LONG;
 	/* from now on we have normal address_space methods */
 	inode->i_data.a_ops = &udf_aops;
+	set_page_dirty(page);
+	unlock_page(page);
 	up_write(&iinfo->i_data_sem);
-	err = inode->i_data.a_ops->writepage(page, &udf_wbc);
+	err = filemap_fdatawrite(inode->i_mapping);
 	if (err) {
 		/* Restore everything back so that we don't lose data... */
 		lock_page(page);
@@ -317,6 +315,7 @@
 		unlock_page(page);
 		iinfo->i_alloc_type = ICBTAG_FLAG_AD_IN_ICB;
 		inode->i_data.a_ops = &udf_adinicb_aops;
+		iinfo->i_lenAlloc = inode->i_size;
 		up_write(&iinfo->i_data_sem);
 	}
 	put_page(page);
@@ -325,96 +324,6 @@
 	return err;
 }
 
-struct buffer_head *udf_expand_dir_adinicb(struct inode *inode,
-					    udf_pblk_t *block, int *err)
-{
-	udf_pblk_t newblock;
-	struct buffer_head *dbh = NULL;
-	struct kernel_lb_addr eloc;
-	uint8_t alloctype;
-	struct extent_position epos;
-
-	struct udf_fileident_bh sfibh, dfibh;
-	loff_t f_pos = udf_ext0_offset(inode);
-	int size = udf_ext0_offset(inode) + inode->i_size;
-	struct fileIdentDesc cfi, *sfi, *dfi;
-	struct udf_inode_info *iinfo = UDF_I(inode);
-
-	if (UDF_QUERY_FLAG(inode->i_sb, UDF_FLAG_USE_SHORT_AD))
-		alloctype = ICBTAG_FLAG_AD_SHORT;
-	else
-		alloctype = ICBTAG_FLAG_AD_LONG;
-
-	if (!inode->i_size) {
-		iinfo->i_alloc_type = alloctype;
-		mark_inode_dirty(inode);
-		return NULL;
-	}
-
-	/* alloc block, and copy data to it */
-	*block = udf_new_block(inode->i_sb, inode,
-			       iinfo->i_location.partitionReferenceNum,
-			       iinfo->i_location.logicalBlockNum, err);
-	if (!(*block))
-		return NULL;
-	newblock = udf_get_pblock(inode->i_sb, *block,
-				  iinfo->i_location.partitionReferenceNum,
-				0);
-	if (!newblock)
-		return NULL;
-	dbh = udf_tgetblk(inode->i_sb, newblock);
-	if (!dbh)
-		return NULL;
-	lock_buffer(dbh);
-	memset(dbh->b_data, 0x00, inode->i_sb->s_blocksize);
-	set_buffer_uptodate(dbh);
-	unlock_buffer(dbh);
-	mark_buffer_dirty_inode(dbh, inode);
-
-	sfibh.soffset = sfibh.eoffset =
-			f_pos & (inode->i_sb->s_blocksize - 1);
-	sfibh.sbh = sfibh.ebh = NULL;
-	dfibh.soffset = dfibh.eoffset = 0;
-	dfibh.sbh = dfibh.ebh = dbh;
-	while (f_pos < size) {
-		iinfo->i_alloc_type = ICBTAG_FLAG_AD_IN_ICB;
-		sfi = udf_fileident_read(inode, &f_pos, &sfibh, &cfi, NULL,
-					 NULL, NULL, NULL);
-		if (!sfi) {
-			brelse(dbh);
-			return NULL;
-		}
-		iinfo->i_alloc_type = alloctype;
-		sfi->descTag.tagLocation = cpu_to_le32(*block);
-		dfibh.soffset = dfibh.eoffset;
-		dfibh.eoffset += (sfibh.eoffset - sfibh.soffset);
-		dfi = (struct fileIdentDesc *)(dbh->b_data + dfibh.soffset);
-		if (udf_write_fi(inode, sfi, dfi, &dfibh, sfi->impUse,
-				 udf_get_fi_ident(sfi))) {
-			iinfo->i_alloc_type = ICBTAG_FLAG_AD_IN_ICB;
-			brelse(dbh);
-			return NULL;
-		}
-	}
-	mark_buffer_dirty_inode(dbh, inode);
-
-	memset(iinfo->i_data + iinfo->i_lenEAttr, 0, iinfo->i_lenAlloc);
-	iinfo->i_lenAlloc = 0;
-	eloc.logicalBlockNum = *block;
-	eloc.partitionReferenceNum =
-				iinfo->i_location.partitionReferenceNum;
-	iinfo->i_lenExtents = inode->i_size;
-	epos.bh = NULL;
-	epos.block = iinfo->i_location;
-	epos.offset = udf_file_entry_alloc_offset(inode);
-	udf_add_aext(inode, &epos, &eloc, inode->i_size, 0);
-	/* UniqueID stuff */
-
-	brelse(epos.bh);
-	mark_inode_dirty(inode);
-	return dbh;
-}
-
 static int udf_get_block(struct inode *inode, sector_t block,
 			 struct buffer_head *bh_result, int create)
 {
@@ -439,6 +348,12 @@
 		iinfo->i_next_alloc_goal++;
 	}
 
+	/*
+	 * Block beyond EOF and prealloc extents? Just discard preallocation
+	 * as it is not useful and complicates things.
+	 */
+	if (((loff_t)block) << inode->i_blkbits >= iinfo->i_lenExtents)
+		udf_discard_prealloc(inode);
 	udf_clear_extent_cache(inode);
 	phys = inode_getblk(inode, block, &err, &new);
 	if (!phys)
@@ -488,8 +403,6 @@
 	uint32_t add;
 	int count = 0, fake = !(last_ext->extLength & UDF_EXTENT_LENGTH_MASK);
 	struct super_block *sb = inode->i_sb;
-	struct kernel_lb_addr prealloc_loc = {};
-	uint32_t prealloc_len = 0;
 	struct udf_inode_info *iinfo;
 	int err;
 
@@ -510,19 +423,6 @@
 			~(sb->s_blocksize - 1);
 	}
 
-	/* Last extent are just preallocated blocks? */
-	if ((last_ext->extLength & UDF_EXTENT_FLAG_MASK) ==
-						EXT_NOT_RECORDED_ALLOCATED) {
-		/* Save the extent so that we can reattach it to the end */
-		prealloc_loc = last_ext->extLocation;
-		prealloc_len = last_ext->extLength;
-		/* Mark the extent as a hole */
-		last_ext->extLength = EXT_NOT_RECORDED_NOT_ALLOCATED |
-			(last_ext->extLength & UDF_EXTENT_LENGTH_MASK);
-		last_ext->extLocation.logicalBlockNum = 0;
-		last_ext->extLocation.partitionReferenceNum = 0;
-	}
-
 	/* Can we merge with the previous extent? */
 	if ((last_ext->extLength & UDF_EXTENT_FLAG_MASK) ==
 					EXT_NOT_RECORDED_NOT_ALLOCATED) {
@@ -535,8 +435,10 @@
 	}
 
 	if (fake) {
-		udf_add_aext(inode, last_pos, &last_ext->extLocation,
-			     last_ext->extLength, 1);
+		err = udf_add_aext(inode, last_pos, &last_ext->extLocation,
+				   last_ext->extLength, 1);
+		if (err < 0)
+			goto out_err;
 		count++;
 	} else {
 		struct kernel_lb_addr tmploc;
@@ -550,7 +452,7 @@
 		 * more extents, we may need to enter possible following
 		 * empty indirect extent.
 		 */
-		if (new_block_bytes || prealloc_len)
+		if (new_block_bytes)
 			udf_next_aext(inode, last_pos, &tmploc, &tmplen, 0);
 	}
 
@@ -570,7 +472,7 @@
 		err = udf_add_aext(inode, last_pos, &last_ext->extLocation,
 				   last_ext->extLength, 1);
 		if (err)
-			return err;
+			goto out_err;
 		count++;
 	}
 	if (new_block_bytes) {
@@ -579,22 +481,11 @@
 		err = udf_add_aext(inode, last_pos, &last_ext->extLocation,
 				   last_ext->extLength, 1);
 		if (err)
-			return err;
+			goto out_err;
 		count++;
 	}
 
 out:
-	/* Do we have some preallocated blocks saved? */
-	if (prealloc_len) {
-		err = udf_add_aext(inode, last_pos, &prealloc_loc,
-				   prealloc_len, 1);
-		if (err)
-			return err;
-		last_ext->extLocation = prealloc_loc;
-		last_ext->extLength = prealloc_len;
-		count++;
-	}
-
 	/* last_pos should point to the last written extent... */
 	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
 		last_pos->offset -= sizeof(struct short_ad);
@@ -604,19 +495,28 @@
 		return -EIO;
 
 	return count;
+out_err:
+	/* Remove extents we've created so far */
+	udf_clear_extent_cache(inode);
+	udf_truncate_extents(inode);
+	return err;
 }
 
 /* Extend the final block of the file to final_block_len bytes */
 static void udf_do_extend_final_block(struct inode *inode,
 				      struct extent_position *last_pos,
 				      struct kernel_long_ad *last_ext,
-				      uint32_t final_block_len)
+				      uint32_t new_elen)
 {
-	struct super_block *sb = inode->i_sb;
 	uint32_t added_bytes;
 
-	added_bytes = final_block_len -
-		      (last_ext->extLength & (sb->s_blocksize - 1));
+	/*
+	 * Extent already large enough? It may be already rounded up to block
+	 * size...
+	 */
+	if (new_elen <= (last_ext->extLength & UDF_EXTENT_LENGTH_MASK))
+		return;
+	added_bytes = new_elen - (last_ext->extLength & UDF_EXTENT_LENGTH_MASK);
 	last_ext->extLength += added_bytes;
 	UDF_I(inode)->i_lenExtents += added_bytes;
 
@@ -633,12 +533,12 @@
 	int8_t etype;
 	struct super_block *sb = inode->i_sb;
 	sector_t first_block = newsize >> sb->s_blocksize_bits, offset;
-	unsigned long partial_final_block;
+	loff_t new_elen;
 	int adsize;
 	struct udf_inode_info *iinfo = UDF_I(inode);
 	struct kernel_long_ad extent;
 	int err = 0;
-	int within_final_block;
+	bool within_last_ext;
 
 	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
 		adsize = sizeof(struct short_ad);
@@ -647,8 +547,17 @@
 	else
 		BUG();
 
+	/*
+	 * When creating hole in file, just don't bother with preserving
+	 * preallocation. It likely won't be very useful anyway.
+	 */
+	udf_discard_prealloc(inode);
+
 	etype = inode_bmap(inode, first_block, &epos, &eloc, &elen, &offset);
-	within_final_block = (etype != -1);
+	within_last_ext = (etype != -1);
+	/* We don't expect extents past EOF... */
+	WARN_ON_ONCE(within_last_ext &&
+		     elen > ((loff_t)offset + 1) << inode->i_blkbits);
 
 	if ((!epos.bh && epos.offset == udf_file_entry_alloc_offset(inode)) ||
 	    (epos.bh && epos.offset == sizeof(struct allocExtDesc))) {
@@ -664,19 +573,17 @@
 		extent.extLength |= etype << 30;
 	}
 
-	partial_final_block = newsize & (sb->s_blocksize - 1);
+	new_elen = ((loff_t)offset << inode->i_blkbits) |
+					(newsize & (sb->s_blocksize - 1));
 
 	/* File has extent covering the new size (could happen when extending
 	 * inside a block)?
 	 */
-	if (within_final_block) {
+	if (within_last_ext) {
 		/* Extending file within the last file block */
-		udf_do_extend_final_block(inode, &epos, &extent,
-					  partial_final_block);
+		udf_do_extend_final_block(inode, &epos, &extent, new_elen);
 	} else {
-		loff_t add = ((loff_t)offset << sb->s_blocksize_bits) |
-			     partial_final_block;
-		err = udf_do_extend_file(inode, &epos, &extent, add);
+		err = udf_do_extend_file(inode, &epos, &extent, new_elen);
 	}
 
 	if (err < 0)
@@ -698,7 +605,7 @@
 	struct kernel_lb_addr eloc, tmpeloc;
 	int c = 1;
 	loff_t lbcount = 0, b_off = 0;
-	udf_pblk_t newblocknum, newblock;
+	udf_pblk_t newblocknum, newblock = 0;
 	sector_t offset = 0;
 	int8_t etype;
 	struct udf_inode_info *iinfo = UDF_I(inode);
@@ -777,10 +684,11 @@
 		goto out_free;
 	}
 
-	/* Are we beyond EOF? */
+	/* Are we beyond EOF and preallocated extent? */
 	if (etype == -1) {
 		int ret;
 		loff_t hole_len;
+
 		isBeyondEOF = true;
 		if (count) {
 			if (c)
@@ -800,25 +708,22 @@
 		ret = udf_do_extend_file(inode, &prev_epos, laarr, hole_len);
 		if (ret < 0) {
 			*err = ret;
-			newblock = 0;
 			goto out_free;
 		}
 		c = 0;
 		offset = 0;
 		count += ret;
-		/* We are not covered by a preallocated extent? */
-		if ((laarr[0].extLength & UDF_EXTENT_FLAG_MASK) !=
-						EXT_NOT_RECORDED_ALLOCATED) {
-			/* Is there any real extent? - otherwise we overwrite
-			 * the fake one... */
-			if (count)
-				c = !c;
-			laarr[c].extLength = EXT_NOT_RECORDED_NOT_ALLOCATED |
-				inode->i_sb->s_blocksize;
-			memset(&laarr[c].extLocation, 0x00,
-				sizeof(struct kernel_lb_addr));
-			count++;
-		}
+		/*
+		 * Is there any real extent? - otherwise we overwrite the fake
+		 * one...
+		 */
+		if (count)
+			c = !c;
+		laarr[c].extLength = EXT_NOT_RECORDED_NOT_ALLOCATED |
+			inode->i_sb->s_blocksize;
+		memset(&laarr[c].extLocation, 0x00,
+			sizeof(struct kernel_lb_addr));
+		count++;
 		endnum = c + 1;
 		lastblock = 1;
 	} else {
@@ -865,7 +770,6 @@
 				goal, err);
 		if (!newblocknum) {
 			*err = -ENOSPC;
-			newblock = 0;
 			goto out_free;
 		}
 		if (isBeyondEOF)
@@ -891,7 +795,9 @@
 	/* write back the new extents, inserting new extents if the new number
 	 * of extents is greater than the old number, and deleting extents if
 	 * the new number of extents is less than the old number */
-	udf_update_extents(inode, laarr, startnum, endnum, &prev_epos);
+	*err = udf_update_extents(inode, laarr, startnum, endnum, &prev_epos);
+	if (*err < 0)
+		goto out_free;
 
 	newblock = udf_get_pblock(inode->i_sb, newblocknum,
 				iinfo->i_location.partitionReferenceNum, 0);
@@ -1095,23 +1001,8 @@
 			blocksize - 1) >> blocksize_bits)))) {
 
 			if (((li->extLength & UDF_EXTENT_LENGTH_MASK) +
-				(lip1->extLength & UDF_EXTENT_LENGTH_MASK) +
-				blocksize - 1) & ~UDF_EXTENT_LENGTH_MASK) {
-				lip1->extLength = (lip1->extLength -
-						  (li->extLength &
-						   UDF_EXTENT_LENGTH_MASK) +
-						   UDF_EXTENT_LENGTH_MASK) &
-							~(blocksize - 1);
-				li->extLength = (li->extLength &
-						 UDF_EXTENT_FLAG_MASK) +
-						(UDF_EXTENT_LENGTH_MASK + 1) -
-						blocksize;
-				lip1->extLocation.logicalBlockNum =
-					li->extLocation.logicalBlockNum +
-					((li->extLength &
-						UDF_EXTENT_LENGTH_MASK) >>
-						blocksize_bits);
-			} else {
+			     (lip1->extLength & UDF_EXTENT_LENGTH_MASK) +
+			     blocksize - 1) <= UDF_EXTENT_LENGTH_MASK) {
 				li->extLength = lip1->extLength +
 					(((li->extLength &
 						UDF_EXTENT_LENGTH_MASK) +
@@ -1174,21 +1065,30 @@
 	}
 }
 
-static void udf_update_extents(struct inode *inode, struct kernel_long_ad *laarr,
-			       int startnum, int endnum,
-			       struct extent_position *epos)
+static int udf_update_extents(struct inode *inode, struct kernel_long_ad *laarr,
+			      int startnum, int endnum,
+			      struct extent_position *epos)
 {
 	int start = 0, i;
 	struct kernel_lb_addr tmploc;
 	uint32_t tmplen;
+	int err;
 
 	if (startnum > endnum) {
 		for (i = 0; i < (startnum - endnum); i++)
 			udf_delete_aext(inode, *epos);
 	} else if (startnum < endnum) {
 		for (i = 0; i < (endnum - startnum); i++) {
-			udf_insert_aext(inode, *epos, laarr[i].extLocation,
-					laarr[i].extLength);
+			err = udf_insert_aext(inode, *epos,
+					      laarr[i].extLocation,
+					      laarr[i].extLength);
+			/*
+			 * If we fail here, we are likely corrupting the extent
+			 * list and leaking blocks. At least stop early to
+			 * limit the damage.
+			 */
+			if (err < 0)
+				return err;
 			udf_next_aext(inode, epos, &laarr[i].extLocation,
 				      &laarr[i].extLength, 1);
 			start++;
@@ -1200,6 +1100,7 @@
 		udf_write_aext(inode, epos, &laarr[i].extLocation,
 			       laarr[i].extLength, 1);
 	}
+	return 0;
 }
 
 struct buffer_head *udf_bread(struct inode *inode, udf_pblk_t block,
@@ -1402,6 +1303,7 @@
 		ret = -EIO;
 		goto out;
 	}
+	iinfo->i_hidden = hidden_inode;
 	iinfo->i_unique = 0;
 	iinfo->i_lenEAttr = 0;
 	iinfo->i_lenExtents = 0;
@@ -1737,8 +1639,12 @@
 
 	if (S_ISDIR(inode->i_mode) && inode->i_nlink > 0)
 		fe->fileLinkCount = cpu_to_le16(inode->i_nlink - 1);
-	else
-		fe->fileLinkCount = cpu_to_le16(inode->i_nlink);
+	else {
+		if (iinfo->i_hidden)
+			fe->fileLinkCount = cpu_to_le16(0);
+		else
+			fe->fileLinkCount = cpu_to_le16(inode->i_nlink);
+	}
 
 	fe->informationLength = cpu_to_le64(inode->i_size);
 
@@ -1909,8 +1815,13 @@
 	if (!inode)
 		return ERR_PTR(-ENOMEM);
 
-	if (!(inode->i_state & I_NEW))
+	if (!(inode->i_state & I_NEW)) {
+		if (UDF_I(inode)->i_hidden != hidden_inode) {
+			iput(inode);
+			return ERR_PTR(-EFSCORRUPTED);
+		}
 		return inode;
+	}
 
 	memcpy(&UDF_I(inode)->i_location, ino, sizeof(struct kernel_lb_addr));
 	err = udf_read_inode(inode, hidden_inode);
@@ -2189,12 +2100,15 @@
 		alen = udf_file_entry_alloc_offset(inode) +
 							iinfo->i_lenAlloc;
 	} else {
+		struct allocExtDesc *header =
+			(struct allocExtDesc *)epos->bh->b_data;
+
 		if (!epos->offset)
 			epos->offset = sizeof(struct allocExtDesc);
 		ptr = epos->bh->b_data + epos->offset;
-		alen = sizeof(struct allocExtDesc) +
-			le32_to_cpu(((struct allocExtDesc *)epos->bh->b_data)->
-							lengthAllocDescs);
+		if (check_add_overflow(sizeof(struct allocExtDesc),
+				le32_to_cpu(header->lengthAllocDescs), &alen))
+			return -1;
 	}
 
 	switch (iinfo->i_alloc_type) {
@@ -2224,12 +2138,13 @@
 	return etype;
 }
 
-static int8_t udf_insert_aext(struct inode *inode, struct extent_position epos,
-			      struct kernel_lb_addr neloc, uint32_t nelen)
+static int udf_insert_aext(struct inode *inode, struct extent_position epos,
+			   struct kernel_lb_addr neloc, uint32_t nelen)
 {
 	struct kernel_lb_addr oeloc;
 	uint32_t oelen;
 	int8_t etype;
+	int err;
 
 	if (epos.bh)
 		get_bh(epos.bh);
@@ -2239,10 +2154,10 @@
 		neloc = oeloc;
 		nelen = (etype << 30) | oelen;
 	}
-	udf_add_aext(inode, &epos, &neloc, nelen, 1);
+	err = udf_add_aext(inode, &epos, &neloc, nelen, 1);
 	brelse(epos.bh);
 
-	return (nelen >> 30);
+	return err;
 }
 
 int8_t udf_delete_aext(struct inode *inode, struct extent_position epos)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/namei.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/namei.c
@@ -30,6 +30,7 @@
 #include <linux/sched.h>
 #include <linux/crc-itu-t.h>
 #include <linux/exportfs.h>
+#include <linux/iversion.h>
 
 static inline int udf_match(int len1, const unsigned char *name1, int len2,
 			    const unsigned char *name2)
@@ -40,281 +41,93 @@
 	return !memcmp(name1, name2, len1);
 }
 
-int udf_write_fi(struct inode *inode, struct fileIdentDesc *cfi,
-		 struct fileIdentDesc *sfi, struct udf_fileident_bh *fibh,
-		 uint8_t *impuse, uint8_t *fileident)
-{
-	uint16_t crclen = fibh->eoffset - fibh->soffset - sizeof(struct tag);
-	uint16_t crc;
-	int offset;
-	uint16_t liu = le16_to_cpu(cfi->lengthOfImpUse);
-	uint8_t lfi = cfi->lengthFileIdent;
-	int padlen = fibh->eoffset - fibh->soffset - liu - lfi -
-		sizeof(struct fileIdentDesc);
-	int adinicb = 0;
-
-	if (UDF_I(inode)->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB)
-		adinicb = 1;
-
-	offset = fibh->soffset + sizeof(struct fileIdentDesc);
-
-	if (impuse) {
-		if (adinicb || (offset + liu < 0)) {
-			memcpy((uint8_t *)sfi->impUse, impuse, liu);
-		} else if (offset >= 0) {
-			memcpy(fibh->ebh->b_data + offset, impuse, liu);
-		} else {
-			memcpy((uint8_t *)sfi->impUse, impuse, -offset);
-			memcpy(fibh->ebh->b_data, impuse - offset,
-				liu + offset);
-		}
-	}
-
-	offset += liu;
-
-	if (fileident) {
-		if (adinicb || (offset + lfi < 0)) {
-			memcpy(udf_get_fi_ident(sfi), fileident, lfi);
-		} else if (offset >= 0) {
-			memcpy(fibh->ebh->b_data + offset, fileident, lfi);
-		} else {
-			memcpy(udf_get_fi_ident(sfi), fileident, -offset);
-			memcpy(fibh->ebh->b_data, fileident - offset,
-				lfi + offset);
-		}
-	}
-
-	offset += lfi;
-
-	if (adinicb || (offset + padlen < 0)) {
-		memset(udf_get_fi_ident(sfi) + lfi, 0x00, padlen);
-	} else if (offset >= 0) {
-		memset(fibh->ebh->b_data + offset, 0x00, padlen);
-	} else {
-		memset(udf_get_fi_ident(sfi) + lfi, 0x00, -offset);
-		memset(fibh->ebh->b_data, 0x00, padlen + offset);
-	}
-
-	crc = crc_itu_t(0, (uint8_t *)cfi + sizeof(struct tag),
-		      sizeof(struct fileIdentDesc) - sizeof(struct tag));
-
-	if (fibh->sbh == fibh->ebh) {
-		crc = crc_itu_t(crc, (uint8_t *)sfi->impUse,
-			      crclen + sizeof(struct tag) -
-			      sizeof(struct fileIdentDesc));
-	} else if (sizeof(struct fileIdentDesc) >= -fibh->soffset) {
-		crc = crc_itu_t(crc, fibh->ebh->b_data +
-					sizeof(struct fileIdentDesc) +
-					fibh->soffset,
-			      crclen + sizeof(struct tag) -
-					sizeof(struct fileIdentDesc));
-	} else {
-		crc = crc_itu_t(crc, (uint8_t *)sfi->impUse,
-			      -fibh->soffset - sizeof(struct fileIdentDesc));
-		crc = crc_itu_t(crc, fibh->ebh->b_data, fibh->eoffset);
-	}
-
-	cfi->descTag.descCRC = cpu_to_le16(crc);
-	cfi->descTag.descCRCLength = cpu_to_le16(crclen);
-	cfi->descTag.tagChecksum = udf_tag_checksum(&cfi->descTag);
-
-	if (adinicb || (sizeof(struct fileIdentDesc) <= -fibh->soffset)) {
-		memcpy((uint8_t *)sfi, (uint8_t *)cfi,
-			sizeof(struct fileIdentDesc));
-	} else {
-		memcpy((uint8_t *)sfi, (uint8_t *)cfi, -fibh->soffset);
-		memcpy(fibh->ebh->b_data, (uint8_t *)cfi - fibh->soffset,
-		       sizeof(struct fileIdentDesc) + fibh->soffset);
-	}
-
-	if (adinicb) {
-		mark_inode_dirty(inode);
-	} else {
-		if (fibh->sbh != fibh->ebh)
-			mark_buffer_dirty_inode(fibh->ebh, inode);
-		mark_buffer_dirty_inode(fibh->sbh, inode);
-	}
-	return 0;
-}
-
 /**
- * udf_find_entry - find entry in given directory.
+ * udf_fiiter_find_entry - find entry in given directory.
  *
  * @dir:	directory inode to search in
  * @child:	qstr of the name
- * @fibh:	buffer head / inode with file identifier descriptor we found
- * @cfi:	found file identifier descriptor with given name
+ * @iter:	iter to use for searching
  *
  * This function searches in the directory @dir for a file name @child. When
- * found, @fibh points to the buffer head(s) (bh is NULL for in ICB
- * directories) containing the file identifier descriptor (FID). In that case
- * the function returns pointer to the FID in the buffer or inode - but note
- * that FID may be split among two buffers (blocks) so accessing it via that
- * pointer isn't easily possible. This pointer can be used only as an iterator
- * for other directory manipulation functions. For inspection of the FID @cfi
- * can be used - the found FID is copied there.
+ * found, @iter points to the position in the directory with given entry.
  *
- * Returns pointer to FID, NULL when nothing found, or error code.
+ * Returns 0 on success, < 0 on error (including -ENOENT).
  */
-static struct fileIdentDesc *udf_find_entry(struct inode *dir,
-					    const struct qstr *child,
-					    struct udf_fileident_bh *fibh,
-					    struct fileIdentDesc *cfi)
+static int udf_fiiter_find_entry(struct inode *dir, const struct qstr *child,
+				 struct udf_fileident_iter *iter)
 {
-	struct fileIdentDesc *fi = NULL;
-	loff_t f_pos;
-	udf_pblk_t block;
 	int flen;
-	unsigned char *fname = NULL, *copy_name = NULL;
-	unsigned char *nameptr;
-	uint8_t lfi;
-	uint16_t liu;
-	loff_t size;
-	struct kernel_lb_addr eloc;
-	uint32_t elen;
-	sector_t offset;
-	struct extent_position epos = {};
-	struct udf_inode_info *dinfo = UDF_I(dir);
+	unsigned char *fname = NULL;
+	struct super_block *sb = dir->i_sb;
 	int isdotdot = child->len == 2 &&
 		child->name[0] == '.' && child->name[1] == '.';
-	struct super_block *sb = dir->i_sb;
-
-	size = udf_ext0_offset(dir) + dir->i_size;
-	f_pos = udf_ext0_offset(dir);
-
-	fibh->sbh = fibh->ebh = NULL;
-	fibh->soffset = fibh->eoffset = f_pos & (sb->s_blocksize - 1);
-	if (dinfo->i_alloc_type != ICBTAG_FLAG_AD_IN_ICB) {
-		if (inode_bmap(dir, f_pos >> sb->s_blocksize_bits, &epos,
-		    &eloc, &elen, &offset) != (EXT_RECORDED_ALLOCATED >> 30)) {
-			fi = ERR_PTR(-EIO);
-			goto out_err;
-		}
-
-		block = udf_get_lb_pblock(sb, &eloc, offset);
-		if ((++offset << sb->s_blocksize_bits) < elen) {
-			if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-				epos.offset -= sizeof(struct short_ad);
-			else if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
-				epos.offset -= sizeof(struct long_ad);
-		} else
-			offset = 0;
-
-		fibh->sbh = fibh->ebh = udf_tread(sb, block);
-		if (!fibh->sbh) {
-			fi = ERR_PTR(-EIO);
-			goto out_err;
-		}
-	}
+	int ret;
 
 	fname = kmalloc(UDF_NAME_LEN, GFP_NOFS);
-	if (!fname) {
-		fi = ERR_PTR(-ENOMEM);
-		goto out_err;
-	}
-
-	while (f_pos < size) {
-		fi = udf_fileident_read(dir, &f_pos, fibh, cfi, &epos, &eloc,
-					&elen, &offset);
-		if (!fi) {
-			fi = ERR_PTR(-EIO);
-			goto out_err;
-		}
-
-		liu = le16_to_cpu(cfi->lengthOfImpUse);
-		lfi = cfi->lengthFileIdent;
+	if (!fname)
+		return -ENOMEM;
 
-		if (fibh->sbh == fibh->ebh) {
-			nameptr = udf_get_fi_ident(fi);
-		} else {
-			int poffset;	/* Unpaded ending offset */
-
-			poffset = fibh->soffset + sizeof(struct fileIdentDesc) +
-					liu + lfi;
-
-			if (poffset >= lfi)
-				nameptr = (uint8_t *)(fibh->ebh->b_data +
-						      poffset - lfi);
-			else {
-				if (!copy_name) {
-					copy_name = kmalloc(UDF_NAME_LEN,
-							    GFP_NOFS);
-					if (!copy_name) {
-						fi = ERR_PTR(-ENOMEM);
-						goto out_err;
-					}
-				}
-				nameptr = copy_name;
-				memcpy(nameptr, udf_get_fi_ident(fi),
-					lfi - poffset);
-				memcpy(nameptr + lfi - poffset,
-					fibh->ebh->b_data, poffset);
-			}
-		}
-
-		if ((cfi->fileCharacteristics & FID_FILE_CHAR_DELETED) != 0) {
+	for (ret = udf_fiiter_init(iter, dir, 0);
+	     !ret && iter->pos < dir->i_size;
+	     ret = udf_fiiter_advance(iter)) {
+		if (iter->fi.fileCharacteristics & FID_FILE_CHAR_DELETED) {
 			if (!UDF_QUERY_FLAG(sb, UDF_FLAG_UNDELETE))
 				continue;
 		}
 
-		if ((cfi->fileCharacteristics & FID_FILE_CHAR_HIDDEN) != 0) {
+		if (iter->fi.fileCharacteristics & FID_FILE_CHAR_HIDDEN) {
 			if (!UDF_QUERY_FLAG(sb, UDF_FLAG_UNHIDE))
 				continue;
 		}
 
-		if ((cfi->fileCharacteristics & FID_FILE_CHAR_PARENT) &&
+		if ((iter->fi.fileCharacteristics & FID_FILE_CHAR_PARENT) &&
 		    isdotdot)
 			goto out_ok;
 
-		if (!lfi)
+		if (!iter->fi.lengthFileIdent)
 			continue;
 
-		flen = udf_get_filename(sb, nameptr, lfi, fname, UDF_NAME_LEN);
+		flen = udf_get_filename(sb, iter->name,
+				iter->fi.lengthFileIdent, fname, UDF_NAME_LEN);
 		if (flen < 0) {
-			fi = ERR_PTR(flen);
+			ret = flen;
 			goto out_err;
 		}
 
 		if (udf_match(flen, fname, child->len, child->name))
 			goto out_ok;
 	}
+	if (!ret)
+		ret = -ENOENT;
 
-	fi = NULL;
 out_err:
-	if (fibh->sbh != fibh->ebh)
-		brelse(fibh->ebh);
-	brelse(fibh->sbh);
+	udf_fiiter_release(iter);
 out_ok:
-	brelse(epos.bh);
 	kfree(fname);
-	kfree(copy_name);
 
-	return fi;
+	return ret;
 }
 
 static struct dentry *udf_lookup(struct inode *dir, struct dentry *dentry,
 				 unsigned int flags)
 {
 	struct inode *inode = NULL;
-	struct fileIdentDesc cfi;
-	struct udf_fileident_bh fibh;
-	struct fileIdentDesc *fi;
+	struct udf_fileident_iter iter;
+	int err;
 
 	if (dentry->d_name.len > UDF_NAME_LEN)
 		return ERR_PTR(-ENAMETOOLONG);
 
-	fi = udf_find_entry(dir, &dentry->d_name, &fibh, &cfi);
-	if (IS_ERR(fi))
-		return ERR_CAST(fi);
+	err = udf_fiiter_find_entry(dir, &dentry->d_name, &iter);
+	if (err < 0 && err != -ENOENT)
+		return ERR_PTR(err);
 
-	if (fi) {
+	if (err == 0) {
 		struct kernel_lb_addr loc;
 
-		if (fibh.sbh != fibh.ebh)
-			brelse(fibh.ebh);
-		brelse(fibh.sbh);
+		loc = lelb_to_cpu(iter.fi.icb.extLocation);
+		udf_fiiter_release(&iter);
 
-		loc = lelb_to_cpu(cfi.icb.extLocation);
 		inode = udf_iget(dir->i_sb, &loc);
 		if (IS_ERR(inode))
 			return ERR_CAST(inode);
@@ -323,281 +136,227 @@
 	return d_splice_alias(inode, dentry);
 }
 
-static struct fileIdentDesc *udf_add_entry(struct inode *dir,
-					   struct dentry *dentry,
-					   struct udf_fileident_bh *fibh,
-					   struct fileIdentDesc *cfi, int *err)
+static int udf_expand_dir_adinicb(struct inode *inode, udf_pblk_t *block)
 {
-	struct super_block *sb = dir->i_sb;
-	struct fileIdentDesc *fi = NULL;
-	unsigned char *name = NULL;
-	int namelen;
-	loff_t f_pos;
-	loff_t size = udf_ext0_offset(dir) + dir->i_size;
-	int nfidlen;
-	udf_pblk_t block;
+	udf_pblk_t newblock;
+	struct buffer_head *dbh = NULL;
 	struct kernel_lb_addr eloc;
-	uint32_t elen = 0;
-	sector_t offset;
-	struct extent_position epos = {};
-	struct udf_inode_info *dinfo;
+	struct extent_position epos;
+	uint8_t alloctype;
+	struct udf_inode_info *iinfo = UDF_I(inode);
+	struct udf_fileident_iter iter;
+	uint8_t *impuse;
+	int ret;
 
-	fibh->sbh = fibh->ebh = NULL;
-	name = kmalloc(UDF_NAME_LEN_CS0, GFP_NOFS);
-	if (!name) {
-		*err = -ENOMEM;
-		goto out_err;
+	if (UDF_QUERY_FLAG(inode->i_sb, UDF_FLAG_USE_SHORT_AD))
+		alloctype = ICBTAG_FLAG_AD_SHORT;
+	else
+		alloctype = ICBTAG_FLAG_AD_LONG;
+
+	if (!inode->i_size) {
+		iinfo->i_alloc_type = alloctype;
+		mark_inode_dirty(inode);
+		return 0;
 	}
 
-	if (dentry) {
-		if (!dentry->d_name.len) {
-			*err = -EINVAL;
-			goto out_err;
-		}
-		namelen = udf_put_filename(sb, dentry->d_name.name,
-					   dentry->d_name.len,
-					   name, UDF_NAME_LEN_CS0);
-		if (!namelen) {
-			*err = -ENAMETOOLONG;
-			goto out_err;
-		}
-	} else {
-		namelen = 0;
+	/* alloc block, and copy data to it */
+	*block = udf_new_block(inode->i_sb, inode,
+			       iinfo->i_location.partitionReferenceNum,
+			       iinfo->i_location.logicalBlockNum, &ret);
+	if (!(*block))
+		return ret;
+	newblock = udf_get_pblock(inode->i_sb, *block,
+				  iinfo->i_location.partitionReferenceNum,
+				0);
+	if (newblock == 0xffffffff)
+		return -EFSCORRUPTED;
+	dbh = udf_tgetblk(inode->i_sb, newblock);
+	if (!dbh)
+		return -ENOMEM;
+	lock_buffer(dbh);
+	memcpy(dbh->b_data, iinfo->i_data, inode->i_size);
+	memset(dbh->b_data + inode->i_size, 0,
+	       inode->i_sb->s_blocksize - inode->i_size);
+	set_buffer_uptodate(dbh);
+	unlock_buffer(dbh);
+
+	/* Drop inline data, add block instead */
+	iinfo->i_alloc_type = alloctype;
+	memset(iinfo->i_data + iinfo->i_lenEAttr, 0, iinfo->i_lenAlloc);
+	iinfo->i_lenAlloc = 0;
+	eloc.logicalBlockNum = *block;
+	eloc.partitionReferenceNum =
+				iinfo->i_location.partitionReferenceNum;
+	iinfo->i_lenExtents = inode->i_size;
+	epos.bh = NULL;
+	epos.block = iinfo->i_location;
+	epos.offset = udf_file_entry_alloc_offset(inode);
+	ret = udf_add_aext(inode, &epos, &eloc, inode->i_size, 0);
+	brelse(epos.bh);
+	if (ret < 0) {
+		brelse(dbh);
+		udf_free_blocks(inode->i_sb, inode, &eloc, 0, 1);
+		return ret;
 	}
+	mark_inode_dirty(inode);
 
-	nfidlen = ALIGN(sizeof(struct fileIdentDesc) + namelen, UDF_NAME_PAD);
+	/* Now fixup tags in moved directory entries */
+	for (ret = udf_fiiter_init(&iter, inode, 0);
+	     !ret && iter.pos < inode->i_size;
+	     ret = udf_fiiter_advance(&iter)) {
+		iter.fi.descTag.tagLocation = cpu_to_le32(*block);
+		if (iter.fi.lengthOfImpUse != cpu_to_le16(0))
+			impuse = dbh->b_data + iter.pos +
+						sizeof(struct fileIdentDesc);
+		else
+			impuse = NULL;
+		udf_fiiter_write_fi(&iter, impuse);
+	}
+	brelse(dbh);
+	/*
+	 * We don't expect the iteration to fail as the directory has been
+	 * already verified to be correct
+	 */
+	WARN_ON_ONCE(ret);
+	udf_fiiter_release(&iter);
 
-	f_pos = udf_ext0_offset(dir);
+	return 0;
+}
 
-	fibh->soffset = fibh->eoffset = f_pos & (dir->i_sb->s_blocksize - 1);
-	dinfo = UDF_I(dir);
-	if (dinfo->i_alloc_type != ICBTAG_FLAG_AD_IN_ICB) {
-		if (inode_bmap(dir, f_pos >> dir->i_sb->s_blocksize_bits, &epos,
-		    &eloc, &elen, &offset) != (EXT_RECORDED_ALLOCATED >> 30)) {
-			block = udf_get_lb_pblock(dir->i_sb,
-					&dinfo->i_location, 0);
-			fibh->soffset = fibh->eoffset = sb->s_blocksize;
-			goto add;
-		}
-		block = udf_get_lb_pblock(dir->i_sb, &eloc, offset);
-		if ((++offset << dir->i_sb->s_blocksize_bits) < elen) {
-			if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-				epos.offset -= sizeof(struct short_ad);
-			else if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
-				epos.offset -= sizeof(struct long_ad);
-		} else
-			offset = 0;
-
-		fibh->sbh = fibh->ebh = udf_tread(dir->i_sb, block);
-		if (!fibh->sbh) {
-			*err = -EIO;
-			goto out_err;
-		}
+static int udf_fiiter_add_entry(struct inode *dir, struct dentry *dentry,
+				struct udf_fileident_iter *iter)
+{
+	struct udf_inode_info *dinfo = UDF_I(dir);
+	int nfidlen, namelen = 0;
+	int ret;
+	int off, blksize = 1 << dir->i_blkbits;
+	udf_pblk_t block;
+	char name[UDF_NAME_LEN_CS0];
 
-		block = dinfo->i_location.logicalBlockNum;
+	if (dentry) {
+		if (!dentry->d_name.len)
+			return -EINVAL;
+		namelen = udf_put_filename(dir->i_sb, dentry->d_name.name,
+					   dentry->d_name.len,
+					   name, UDF_NAME_LEN_CS0);
+		if (!namelen)
+			return -ENAMETOOLONG;
 	}
+	nfidlen = ALIGN(sizeof(struct fileIdentDesc) + namelen, UDF_NAME_PAD);
 
-	while (f_pos < size) {
-		fi = udf_fileident_read(dir, &f_pos, fibh, cfi, &epos, &eloc,
-					&elen, &offset);
-
-		if (!fi) {
-			*err = -EIO;
-			goto out_err;
-		}
-
-		if ((cfi->fileCharacteristics & FID_FILE_CHAR_DELETED) != 0) {
-			if (udf_dir_entry_len(cfi) == nfidlen) {
-				cfi->descTag.tagSerialNum = cpu_to_le16(1);
-				cfi->fileVersionNum = cpu_to_le16(1);
-				cfi->fileCharacteristics = 0;
-				cfi->lengthFileIdent = namelen;
-				cfi->lengthOfImpUse = cpu_to_le16(0);
-				if (!udf_write_fi(dir, cfi, fi, fibh, NULL,
-						  name))
-					goto out_ok;
-				else {
-					*err = -EIO;
-					goto out_err;
-				}
+	for (ret = udf_fiiter_init(iter, dir, 0);
+	     !ret && iter->pos < dir->i_size;
+	     ret = udf_fiiter_advance(iter)) {
+		if (iter->fi.fileCharacteristics & FID_FILE_CHAR_DELETED) {
+			if (udf_dir_entry_len(&iter->fi) == nfidlen) {
+				iter->fi.descTag.tagSerialNum = cpu_to_le16(1);
+				iter->fi.fileVersionNum = cpu_to_le16(1);
+				iter->fi.fileCharacteristics = 0;
+				iter->fi.lengthFileIdent = namelen;
+				iter->fi.lengthOfImpUse = cpu_to_le16(0);
+				memcpy(iter->namebuf, name, namelen);
+				iter->name = iter->namebuf;
+				return 0;
 			}
 		}
 	}
-
-add:
-	f_pos += nfidlen;
-
+	if (ret) {
+		udf_fiiter_release(iter);
+		return ret;
+	}
 	if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB &&
-	    sb->s_blocksize - fibh->eoffset < nfidlen) {
-		brelse(epos.bh);
-		epos.bh = NULL;
-		fibh->soffset -= udf_ext0_offset(dir);
-		fibh->eoffset -= udf_ext0_offset(dir);
-		f_pos -= udf_ext0_offset(dir);
-		if (fibh->sbh != fibh->ebh)
-			brelse(fibh->ebh);
-		brelse(fibh->sbh);
-		fibh->sbh = fibh->ebh =
-				udf_expand_dir_adinicb(dir, &block, err);
-		if (!fibh->sbh)
-			goto out_err;
-		epos.block = dinfo->i_location;
-		epos.offset = udf_file_entry_alloc_offset(dir);
-		/* Load extent udf_expand_dir_adinicb() has created */
-		udf_current_aext(dir, &epos, &eloc, &elen, 1);
+	    blksize - udf_ext0_offset(dir) - iter->pos < nfidlen) {
+		udf_fiiter_release(iter);
+		ret = udf_expand_dir_adinicb(dir, &block);
+		if (ret)
+			return ret;
+		ret = udf_fiiter_init(iter, dir, dir->i_size);
+		if (ret < 0)
+			return ret;
 	}
 
-	/* Entry fits into current block? */
-	if (sb->s_blocksize - fibh->eoffset >= nfidlen) {
-		fibh->soffset = fibh->eoffset;
-		fibh->eoffset += nfidlen;
-		if (fibh->sbh != fibh->ebh) {
-			brelse(fibh->sbh);
-			fibh->sbh = fibh->ebh;
-		}
-
-		if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
-			block = dinfo->i_location.logicalBlockNum;
-			fi = (struct fileIdentDesc *)
-					(dinfo->i_data + fibh->soffset -
-					 udf_ext0_offset(dir) +
-					 dinfo->i_lenEAttr);
-		} else {
-			block = eloc.logicalBlockNum +
-					((elen - 1) >>
-						dir->i_sb->s_blocksize_bits);
-			fi = (struct fileIdentDesc *)
-				(fibh->sbh->b_data + fibh->soffset);
-		}
+	/* Get blocknumber to use for entry tag */
+	if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
+		block = dinfo->i_location.logicalBlockNum;
 	} else {
-		/* Round up last extent in the file */
-		elen = (elen + sb->s_blocksize - 1) & ~(sb->s_blocksize - 1);
-		if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-			epos.offset -= sizeof(struct short_ad);
-		else if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
-			epos.offset -= sizeof(struct long_ad);
-		udf_write_aext(dir, &epos, &eloc, elen, 1);
-		dinfo->i_lenExtents = (dinfo->i_lenExtents + sb->s_blocksize
-					- 1) & ~(sb->s_blocksize - 1);
-
-		fibh->soffset = fibh->eoffset - sb->s_blocksize;
-		fibh->eoffset += nfidlen - sb->s_blocksize;
-		if (fibh->sbh != fibh->ebh) {
-			brelse(fibh->sbh);
-			fibh->sbh = fibh->ebh;
-		}
-
-		block = eloc.logicalBlockNum + ((elen - 1) >>
-						dir->i_sb->s_blocksize_bits);
-		fibh->ebh = udf_bread(dir,
-				f_pos >> dir->i_sb->s_blocksize_bits, 1, err);
-		if (!fibh->ebh)
-			goto out_err;
-		/* Extents could have been merged, invalidate our position */
-		brelse(epos.bh);
-		epos.bh = NULL;
-		epos.block = dinfo->i_location;
-		epos.offset = udf_file_entry_alloc_offset(dir);
-
-		if (!fibh->soffset) {
-			/* Find the freshly allocated block */
-			while (udf_next_aext(dir, &epos, &eloc, &elen, 1) ==
-				(EXT_RECORDED_ALLOCATED >> 30))
-				;
-			block = eloc.logicalBlockNum + ((elen - 1) >>
-					dir->i_sb->s_blocksize_bits);
-			brelse(fibh->sbh);
-			fibh->sbh = fibh->ebh;
-			fi = (struct fileIdentDesc *)(fibh->sbh->b_data);
-		} else {
-			fi = (struct fileIdentDesc *)
-				(fibh->sbh->b_data + sb->s_blocksize +
-					fibh->soffset);
-		}
+		block = iter->eloc.logicalBlockNum +
+				((iter->elen - 1) >> dir->i_blkbits);
 	}
+	off = iter->pos & (blksize - 1);
+	if (!off)
+		off = blksize;
+	/* Entry fits into current block? */
+	if (blksize - udf_ext0_offset(dir) - off >= nfidlen)
+		goto store_fi;
 
-	memset(cfi, 0, sizeof(struct fileIdentDesc));
-	if (UDF_SB(sb)->s_udfrev >= 0x0200)
-		udf_new_tag((char *)cfi, TAG_IDENT_FID, 3, 1, block,
+	ret = udf_fiiter_append_blk(iter);
+	if (ret) {
+		udf_fiiter_release(iter);
+		return ret;
+	}
+
+	/* Entry will be completely in the new block? Update tag location... */
+	if (!(iter->pos & (blksize - 1)))
+		block = iter->eloc.logicalBlockNum +
+				((iter->elen - 1) >> dir->i_blkbits);
+store_fi:
+	memset(&iter->fi, 0, sizeof(struct fileIdentDesc));
+	if (UDF_SB(dir->i_sb)->s_udfrev >= 0x0200)
+		udf_new_tag((char *)(&iter->fi), TAG_IDENT_FID, 3, 1, block,
 			    sizeof(struct tag));
 	else
-		udf_new_tag((char *)cfi, TAG_IDENT_FID, 2, 1, block,
+		udf_new_tag((char *)(&iter->fi), TAG_IDENT_FID, 2, 1, block,
 			    sizeof(struct tag));
-	cfi->fileVersionNum = cpu_to_le16(1);
-	cfi->lengthFileIdent = namelen;
-	cfi->lengthOfImpUse = cpu_to_le16(0);
-	if (!udf_write_fi(dir, cfi, fi, fibh, NULL, name)) {
-		dir->i_size += nfidlen;
-		if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB)
-			dinfo->i_lenAlloc += nfidlen;
-		else {
-			/* Find the last extent and truncate it to proper size */
-			while (udf_next_aext(dir, &epos, &eloc, &elen, 1) ==
-				(EXT_RECORDED_ALLOCATED >> 30))
-				;
-			elen -= dinfo->i_lenExtents - dir->i_size;
-			if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-				epos.offset -= sizeof(struct short_ad);
-			else if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
-				epos.offset -= sizeof(struct long_ad);
-			udf_write_aext(dir, &epos, &eloc, elen, 1);
-			dinfo->i_lenExtents = dir->i_size;
-		}
-
-		mark_inode_dirty(dir);
-		goto out_ok;
+	iter->fi.fileVersionNum = cpu_to_le16(1);
+	iter->fi.lengthFileIdent = namelen;
+	iter->fi.lengthOfImpUse = cpu_to_le16(0);
+	memcpy(iter->namebuf, name, namelen);
+	iter->name = iter->namebuf;
+
+	dir->i_size += nfidlen;
+	if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
+		dinfo->i_lenAlloc += nfidlen;
 	} else {
-		*err = -EIO;
-		goto out_err;
+		/* Truncate last extent to proper size */
+		udf_fiiter_update_elen(iter, iter->elen -
+					(dinfo->i_lenExtents - dir->i_size));
 	}
+	mark_inode_dirty(dir);
 
-out_err:
-	fi = NULL;
-	if (fibh->sbh != fibh->ebh)
-		brelse(fibh->ebh);
-	brelse(fibh->sbh);
-out_ok:
-	brelse(epos.bh);
-	kfree(name);
-	return fi;
+	return 0;
 }
 
-static int udf_delete_entry(struct inode *inode, struct fileIdentDesc *fi,
-			    struct udf_fileident_bh *fibh,
-			    struct fileIdentDesc *cfi)
+static void udf_fiiter_delete_entry(struct udf_fileident_iter *iter)
 {
-	cfi->fileCharacteristics |= FID_FILE_CHAR_DELETED;
+	iter->fi.fileCharacteristics |= FID_FILE_CHAR_DELETED;
 
-	if (UDF_QUERY_FLAG(inode->i_sb, UDF_FLAG_STRICT))
-		memset(&(cfi->icb), 0x00, sizeof(struct long_ad));
+	if (UDF_QUERY_FLAG(iter->dir->i_sb, UDF_FLAG_STRICT))
+		memset(&iter->fi.icb, 0x00, sizeof(struct long_ad));
 
-	return udf_write_fi(inode, cfi, fi, fibh, NULL, NULL);
+	udf_fiiter_write_fi(iter, NULL);
 }
 
 static int udf_add_nondir(struct dentry *dentry, struct inode *inode)
 {
 	struct udf_inode_info *iinfo = UDF_I(inode);
 	struct inode *dir = d_inode(dentry->d_parent);
-	struct udf_fileident_bh fibh;
-	struct fileIdentDesc cfi, *fi;
+	struct udf_fileident_iter iter;
 	int err;
 
-	fi = udf_add_entry(dir, dentry, &fibh, &cfi, &err);
-	if (unlikely(!fi)) {
+	err = udf_fiiter_add_entry(dir, dentry, &iter);
+	if (err) {
 		inode_dec_link_count(inode);
 		discard_new_inode(inode);
 		return err;
 	}
-	cfi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
-	cfi.icb.extLocation = cpu_to_lelb(iinfo->i_location);
-	*(__le32 *)((struct allocDescImpUse *)cfi.icb.impUse)->impUse =
+	iter.fi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
+	iter.fi.icb.extLocation = cpu_to_lelb(iinfo->i_location);
+	*(__le32 *)((struct allocDescImpUse *)iter.fi.icb.impUse)->impUse =
 		cpu_to_le32(iinfo->i_unique & 0x00000000FFFFFFFFUL);
-	udf_write_fi(dir, &cfi, fi, &fibh, NULL, NULL);
+	udf_fiiter_write_fi(&iter, NULL);
 	dir->i_ctime = dir->i_mtime = current_time(dir);
 	mark_inode_dirty(dir);
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
+	udf_fiiter_release(&iter);
 	d_instantiate_new(dentry, inode);
 
 	return 0;
@@ -662,8 +421,7 @@
 		     struct dentry *dentry, umode_t mode)
 {
 	struct inode *inode;
-	struct udf_fileident_bh fibh;
-	struct fileIdentDesc cfi, *fi;
+	struct udf_fileident_iter iter;
 	int err;
 	struct udf_inode_info *dinfo = UDF_I(dir);
 	struct udf_inode_info *iinfo;
@@ -675,144 +433,82 @@
 	iinfo = UDF_I(inode);
 	inode->i_op = &udf_dir_inode_operations;
 	inode->i_fop = &udf_dir_operations;
-	fi = udf_add_entry(inode, NULL, &fibh, &cfi, &err);
-	if (!fi) {
-		inode_dec_link_count(inode);
+	err = udf_fiiter_add_entry(inode, NULL, &iter);
+	if (err) {
+		clear_nlink(inode);
 		discard_new_inode(inode);
-		goto out;
+		return err;
 	}
 	set_nlink(inode, 2);
-	cfi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
-	cfi.icb.extLocation = cpu_to_lelb(dinfo->i_location);
-	*(__le32 *)((struct allocDescImpUse *)cfi.icb.impUse)->impUse =
+	iter.fi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
+	iter.fi.icb.extLocation = cpu_to_lelb(dinfo->i_location);
+	*(__le32 *)((struct allocDescImpUse *)iter.fi.icb.impUse)->impUse =
 		cpu_to_le32(dinfo->i_unique & 0x00000000FFFFFFFFUL);
-	cfi.fileCharacteristics =
+	iter.fi.fileCharacteristics =
 			FID_FILE_CHAR_DIRECTORY | FID_FILE_CHAR_PARENT;
-	udf_write_fi(inode, &cfi, fi, &fibh, NULL, NULL);
-	brelse(fibh.sbh);
+	udf_fiiter_write_fi(&iter, NULL);
+	udf_fiiter_release(&iter);
 	mark_inode_dirty(inode);
 
-	fi = udf_add_entry(dir, dentry, &fibh, &cfi, &err);
-	if (!fi) {
+	err = udf_fiiter_add_entry(dir, dentry, &iter);
+	if (err) {
 		clear_nlink(inode);
-		mark_inode_dirty(inode);
 		discard_new_inode(inode);
-		goto out;
+		return err;
 	}
-	cfi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
-	cfi.icb.extLocation = cpu_to_lelb(iinfo->i_location);
-	*(__le32 *)((struct allocDescImpUse *)cfi.icb.impUse)->impUse =
+	iter.fi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
+	iter.fi.icb.extLocation = cpu_to_lelb(iinfo->i_location);
+	*(__le32 *)((struct allocDescImpUse *)iter.fi.icb.impUse)->impUse =
 		cpu_to_le32(iinfo->i_unique & 0x00000000FFFFFFFFUL);
-	cfi.fileCharacteristics |= FID_FILE_CHAR_DIRECTORY;
-	udf_write_fi(dir, &cfi, fi, &fibh, NULL, NULL);
+	iter.fi.fileCharacteristics |= FID_FILE_CHAR_DIRECTORY;
+	udf_fiiter_write_fi(&iter, NULL);
+	udf_fiiter_release(&iter);
 	inc_nlink(dir);
 	dir->i_ctime = dir->i_mtime = current_time(dir);
 	mark_inode_dirty(dir);
 	d_instantiate_new(dentry, inode);
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
-	err = 0;
 
-out:
-	return err;
+	return 0;
 }
 
 static int empty_dir(struct inode *dir)
 {
-	struct fileIdentDesc *fi, cfi;
-	struct udf_fileident_bh fibh;
-	loff_t f_pos;
-	loff_t size = udf_ext0_offset(dir) + dir->i_size;
-	udf_pblk_t block;
-	struct kernel_lb_addr eloc;
-	uint32_t elen;
-	sector_t offset;
-	struct extent_position epos = {};
-	struct udf_inode_info *dinfo = UDF_I(dir);
-
-	f_pos = udf_ext0_offset(dir);
-	fibh.soffset = fibh.eoffset = f_pos & (dir->i_sb->s_blocksize - 1);
-
-	if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB)
-		fibh.sbh = fibh.ebh = NULL;
-	else if (inode_bmap(dir, f_pos >> dir->i_sb->s_blocksize_bits,
-			      &epos, &eloc, &elen, &offset) ==
-					(EXT_RECORDED_ALLOCATED >> 30)) {
-		block = udf_get_lb_pblock(dir->i_sb, &eloc, offset);
-		if ((++offset << dir->i_sb->s_blocksize_bits) < elen) {
-			if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-				epos.offset -= sizeof(struct short_ad);
-			else if (dinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
-				epos.offset -= sizeof(struct long_ad);
-		} else
-			offset = 0;
-
-		fibh.sbh = fibh.ebh = udf_tread(dir->i_sb, block);
-		if (!fibh.sbh) {
-			brelse(epos.bh);
-			return 0;
-		}
-	} else {
-		brelse(epos.bh);
-		return 0;
-	}
-
-	while (f_pos < size) {
-		fi = udf_fileident_read(dir, &f_pos, &fibh, &cfi, &epos, &eloc,
-					&elen, &offset);
-		if (!fi) {
-			if (fibh.sbh != fibh.ebh)
-				brelse(fibh.ebh);
-			brelse(fibh.sbh);
-			brelse(epos.bh);
-			return 0;
-		}
+	struct udf_fileident_iter iter;
+	int ret;
 
-		if (cfi.lengthFileIdent &&
-		    (cfi.fileCharacteristics & FID_FILE_CHAR_DELETED) == 0) {
-			if (fibh.sbh != fibh.ebh)
-				brelse(fibh.ebh);
-			brelse(fibh.sbh);
-			brelse(epos.bh);
+	for (ret = udf_fiiter_init(&iter, dir, 0);
+	     !ret && iter.pos < dir->i_size;
+	     ret = udf_fiiter_advance(&iter)) {
+		if (iter.fi.lengthFileIdent &&
+		    !(iter.fi.fileCharacteristics & FID_FILE_CHAR_DELETED)) {
+			udf_fiiter_release(&iter);
 			return 0;
 		}
 	}
-
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
-	brelse(epos.bh);
+	udf_fiiter_release(&iter);
 
 	return 1;
 }
 
 static int udf_rmdir(struct inode *dir, struct dentry *dentry)
 {
-	int retval;
+	int ret;
 	struct inode *inode = d_inode(dentry);
-	struct udf_fileident_bh fibh;
-	struct fileIdentDesc *fi, cfi;
+	struct udf_fileident_iter iter;
 	struct kernel_lb_addr tloc;
 
-	retval = -ENOENT;
-	fi = udf_find_entry(dir, &dentry->d_name, &fibh, &cfi);
-	if (IS_ERR_OR_NULL(fi)) {
-		if (fi)
-			retval = PTR_ERR(fi);
+	ret = udf_fiiter_find_entry(dir, &dentry->d_name, &iter);
+	if (ret)
 		goto out;
-	}
 
-	retval = -EIO;
-	tloc = lelb_to_cpu(cfi.icb.extLocation);
+	ret = -EFSCORRUPTED;
+	tloc = lelb_to_cpu(iter.fi.icb.extLocation);
 	if (udf_get_lb_pblock(dir->i_sb, &tloc, 0) != inode->i_ino)
 		goto end_rmdir;
-	retval = -ENOTEMPTY;
+	ret = -ENOTEMPTY;
 	if (!empty_dir(inode))
 		goto end_rmdir;
-	retval = udf_delete_entry(dir, fi, &fibh, &cfi);
-	if (retval)
-		goto end_rmdir;
+	udf_fiiter_delete_entry(&iter);
 	if (inode->i_nlink != 2)
 		udf_warn(inode->i_sb, "empty directory has nlink != 2 (%u)\n",
 			 inode->i_nlink);
@@ -822,36 +518,26 @@
 	inode->i_ctime = dir->i_ctime = dir->i_mtime =
 						current_time(inode);
 	mark_inode_dirty(dir);
-
+	ret = 0;
 end_rmdir:
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
-
+	udf_fiiter_release(&iter);
 out:
-	return retval;
+	return ret;
 }
 
 static int udf_unlink(struct inode *dir, struct dentry *dentry)
 {
-	int retval;
+	int ret;
 	struct inode *inode = d_inode(dentry);
-	struct udf_fileident_bh fibh;
-	struct fileIdentDesc *fi;
-	struct fileIdentDesc cfi;
+	struct udf_fileident_iter iter;
 	struct kernel_lb_addr tloc;
 
-	retval = -ENOENT;
-	fi = udf_find_entry(dir, &dentry->d_name, &fibh, &cfi);
-
-	if (IS_ERR_OR_NULL(fi)) {
-		if (fi)
-			retval = PTR_ERR(fi);
+	ret = udf_fiiter_find_entry(dir, &dentry->d_name, &iter);
+	if (ret)
 		goto out;
-	}
 
-	retval = -EIO;
-	tloc = lelb_to_cpu(cfi.icb.extLocation);
+	ret = -EFSCORRUPTED;
+	tloc = lelb_to_cpu(iter.fi.icb.extLocation);
 	if (udf_get_lb_pblock(dir->i_sb, &tloc, 0) != inode->i_ino)
 		goto end_unlink;
 
@@ -860,22 +546,16 @@
 			  inode->i_ino, inode->i_nlink);
 		set_nlink(inode, 1);
 	}
-	retval = udf_delete_entry(dir, fi, &fibh, &cfi);
-	if (retval)
-		goto end_unlink;
+	udf_fiiter_delete_entry(&iter);
 	dir->i_ctime = dir->i_mtime = current_time(dir);
 	mark_inode_dirty(dir);
 	inode_dec_link_count(inode);
 	inode->i_ctime = dir->i_ctime;
-	retval = 0;
-
+	ret = 0;
 end_unlink:
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
-
+	udf_fiiter_release(&iter);
 out:
-	return retval;
+	return ret;
 }
 
 static int udf_symlink(struct user_namespace *mnt_userns, struct inode *dir,
@@ -1035,27 +715,21 @@
 		    struct dentry *dentry)
 {
 	struct inode *inode = d_inode(old_dentry);
-	struct udf_fileident_bh fibh;
-	struct fileIdentDesc cfi, *fi;
+	struct udf_fileident_iter iter;
 	int err;
 
-	fi = udf_add_entry(dir, dentry, &fibh, &cfi, &err);
-	if (!fi) {
+	err = udf_fiiter_add_entry(dir, dentry, &iter);
+	if (err)
 		return err;
-	}
-	cfi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
-	cfi.icb.extLocation = cpu_to_lelb(UDF_I(inode)->i_location);
+	iter.fi.icb.extLength = cpu_to_le32(inode->i_sb->s_blocksize);
+	iter.fi.icb.extLocation = cpu_to_lelb(UDF_I(inode)->i_location);
 	if (UDF_SB(inode->i_sb)->s_lvid_bh) {
-		*(__le32 *)((struct allocDescImpUse *)cfi.icb.impUse)->impUse =
+		*(__le32 *)((struct allocDescImpUse *)iter.fi.icb.impUse)->impUse =
 			cpu_to_le32(lvid_get_unique_id(inode->i_sb));
 	}
-	udf_write_fi(dir, &cfi, fi, &fibh, NULL, NULL);
-	if (UDF_I(dir)->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB)
-		mark_inode_dirty(dir);
-
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
+	udf_fiiter_write_fi(&iter, NULL);
+	udf_fiiter_release(&iter);
+
 	inc_nlink(inode);
 	inode->i_ctime = current_time(inode);
 	mark_inode_dirty(inode);
@@ -1076,78 +750,68 @@
 {
 	struct inode *old_inode = d_inode(old_dentry);
 	struct inode *new_inode = d_inode(new_dentry);
-	struct udf_fileident_bh ofibh, nfibh;
-	struct fileIdentDesc *ofi = NULL, *nfi = NULL, *dir_fi = NULL;
-	struct fileIdentDesc ocfi, ncfi;
-	struct buffer_head *dir_bh = NULL;
-	int retval = -ENOENT;
+	struct udf_fileident_iter oiter, niter, diriter;
+	bool has_diriter = false;
+	int retval;
 	struct kernel_lb_addr tloc;
-	struct udf_inode_info *old_iinfo = UDF_I(old_inode);
 
 	if (flags & ~RENAME_NOREPLACE)
 		return -EINVAL;
 
-	ofi = udf_find_entry(old_dir, &old_dentry->d_name, &ofibh, &ocfi);
-	if (IS_ERR(ofi)) {
-		retval = PTR_ERR(ofi);
-		goto end_rename;
-	}
-
-	if (ofibh.sbh != ofibh.ebh)
-		brelse(ofibh.ebh);
-
-	brelse(ofibh.sbh);
-	tloc = lelb_to_cpu(ocfi.icb.extLocation);
-	if (!ofi || udf_get_lb_pblock(old_dir->i_sb, &tloc, 0)
-	    != old_inode->i_ino)
-		goto end_rename;
-
-	nfi = udf_find_entry(new_dir, &new_dentry->d_name, &nfibh, &ncfi);
-	if (IS_ERR(nfi)) {
-		retval = PTR_ERR(nfi);
-		goto end_rename;
-	}
-	if (nfi && !new_inode) {
-		if (nfibh.sbh != nfibh.ebh)
-			brelse(nfibh.ebh);
-		brelse(nfibh.sbh);
-		nfi = NULL;
+	retval = udf_fiiter_find_entry(old_dir, &old_dentry->d_name, &oiter);
+	if (retval)
+		return retval;
+
+	tloc = lelb_to_cpu(oiter.fi.icb.extLocation);
+	if (udf_get_lb_pblock(old_dir->i_sb, &tloc, 0) != old_inode->i_ino) {
+		retval = -ENOENT;
+		goto out_oiter;
 	}
-	if (S_ISDIR(old_inode->i_mode)) {
-		int offset = udf_ext0_offset(old_inode);
 
+	if (S_ISDIR(old_inode->i_mode)) {
 		if (new_inode) {
 			retval = -ENOTEMPTY;
 			if (!empty_dir(new_inode))
-				goto end_rename;
-		}
-		retval = -EIO;
-		if (old_iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) {
-			dir_fi = udf_get_fileident(
-					old_iinfo->i_data -
-					  (old_iinfo->i_efe ?
-					   sizeof(struct extendedFileEntry) :
-					   sizeof(struct fileEntry)),
-					old_inode->i_sb->s_blocksize, &offset);
-		} else {
-			dir_bh = udf_bread(old_inode, 0, 0, &retval);
-			if (!dir_bh)
-				goto end_rename;
-			dir_fi = udf_get_fileident(dir_bh->b_data,
-					old_inode->i_sb->s_blocksize, &offset);
+				goto out_oiter;
 		}
-		if (!dir_fi)
-			goto end_rename;
-		tloc = lelb_to_cpu(dir_fi->icb.extLocation);
+		retval = udf_fiiter_find_entry(old_inode, &dotdot_name,
+					       &diriter);
+		if (retval == -ENOENT) {
+			udf_err(old_inode->i_sb,
+				"directory (ino %lu) has no '..' entry\n",
+				old_inode->i_ino);
+			retval = -EFSCORRUPTED;
+		}
+		if (retval)
+			goto out_oiter;
+		has_diriter = true;
+		tloc = lelb_to_cpu(diriter.fi.icb.extLocation);
 		if (udf_get_lb_pblock(old_inode->i_sb, &tloc, 0) !=
-				old_dir->i_ino)
-			goto end_rename;
+				old_dir->i_ino) {
+			retval = -EFSCORRUPTED;
+			udf_err(old_inode->i_sb,
+				"directory (ino %lu) has parent entry pointing to another inode (%lu != %u)\n",
+				old_inode->i_ino, old_dir->i_ino,
+				udf_get_lb_pblock(old_inode->i_sb, &tloc, 0));
+			goto out_oiter;
+		}
 	}
-	if (!nfi) {
-		nfi = udf_add_entry(new_dir, new_dentry, &nfibh, &ncfi,
-				    &retval);
-		if (!nfi)
-			goto end_rename;
+
+	retval = udf_fiiter_find_entry(new_dir, &new_dentry->d_name, &niter);
+	if (retval && retval != -ENOENT)
+		goto out_oiter;
+	/* Entry found but not passed by VFS? */
+	if (!retval && !new_inode) {
+		retval = -EFSCORRUPTED;
+		udf_fiiter_release(&niter);
+		goto out_oiter;
+	}
+	/* Entry not found? Need to add one... */
+	if (retval) {
+		udf_fiiter_release(&niter);
+		retval = udf_fiiter_add_entry(new_dir, new_dentry, &niter);
+		if (retval)
+			goto out_oiter;
 	}
 
 	/*
@@ -1160,14 +824,26 @@
 	/*
 	 * ok, that's it
 	 */
-	ncfi.fileVersionNum = ocfi.fileVersionNum;
-	ncfi.fileCharacteristics = ocfi.fileCharacteristics;
-	memcpy(&(ncfi.icb), &(ocfi.icb), sizeof(ocfi.icb));
-	udf_write_fi(new_dir, &ncfi, nfi, &nfibh, NULL, NULL);
-
-	/* The old fid may have moved - find it again */
-	ofi = udf_find_entry(old_dir, &old_dentry->d_name, &ofibh, &ocfi);
-	udf_delete_entry(old_dir, ofi, &ofibh, &ocfi);
+	niter.fi.fileVersionNum = oiter.fi.fileVersionNum;
+	niter.fi.fileCharacteristics = oiter.fi.fileCharacteristics;
+	memcpy(&(niter.fi.icb), &(oiter.fi.icb), sizeof(oiter.fi.icb));
+	udf_fiiter_write_fi(&niter, NULL);
+	udf_fiiter_release(&niter);
+
+	/*
+	 * The old entry may have moved due to new entry allocation. Find it
+	 * again.
+	 */
+	udf_fiiter_release(&oiter);
+	retval = udf_fiiter_find_entry(old_dir, &old_dentry->d_name, &oiter);
+	if (retval) {
+		udf_err(old_dir->i_sb,
+			"failed to find renamed entry again in directory (ino %lu)\n",
+			old_dir->i_ino);
+	} else {
+		udf_fiiter_delete_entry(&oiter);
+		udf_fiiter_release(&oiter);
+	}
 
 	if (new_inode) {
 		new_inode->i_ctime = current_time(new_inode);
@@ -1178,13 +854,11 @@
 	mark_inode_dirty(old_dir);
 	mark_inode_dirty(new_dir);
 
-	if (dir_fi) {
-		dir_fi->icb.extLocation = cpu_to_lelb(UDF_I(new_dir)->i_location);
-		udf_update_tag((char *)dir_fi, udf_dir_entry_len(dir_fi));
-		if (old_iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB)
-			mark_inode_dirty(old_inode);
-		else
-			mark_buffer_dirty_inode(dir_bh, old_inode);
+	if (has_diriter) {
+		diriter.fi.icb.extLocation =
+					cpu_to_lelb(UDF_I(new_dir)->i_location);
+		udf_fiiter_write_fi(&diriter, NULL);
+		udf_fiiter_release(&diriter);
 
 		inode_dec_link_count(old_dir);
 		if (new_inode)
@@ -1194,22 +868,11 @@
 			mark_inode_dirty(new_dir);
 		}
 	}
-
-	if (ofi) {
-		if (ofibh.sbh != ofibh.ebh)
-			brelse(ofibh.ebh);
-		brelse(ofibh.sbh);
-	}
-
-	retval = 0;
-
-end_rename:
-	brelse(dir_bh);
-	if (nfi) {
-		if (nfibh.sbh != nfibh.ebh)
-			brelse(nfibh.ebh);
-		brelse(nfibh.sbh);
-	}
+	return 0;
+out_oiter:
+	if (has_diriter)
+		udf_fiiter_release(&diriter);
+	udf_fiiter_release(&oiter);
 
 	return retval;
 }
@@ -1218,17 +881,15 @@
 {
 	struct kernel_lb_addr tloc;
 	struct inode *inode = NULL;
-	struct fileIdentDesc cfi;
-	struct udf_fileident_bh fibh;
-
-	if (!udf_find_entry(d_inode(child), &dotdot_name, &fibh, &cfi))
-		return ERR_PTR(-EACCES);
+	struct udf_fileident_iter iter;
+	int err;
 
-	if (fibh.sbh != fibh.ebh)
-		brelse(fibh.ebh);
-	brelse(fibh.sbh);
+	err = udf_fiiter_find_entry(d_inode(child), &dotdot_name, &iter);
+	if (err)
+		return ERR_PTR(err);
 
-	tloc = lelb_to_cpu(cfi.icb.extLocation);
+	tloc = lelb_to_cpu(iter.fi.icb.extLocation);
+	udf_fiiter_release(&iter);
 	inode = udf_iget(child->d_sb, &tloc);
 	if (IS_ERR(inode))
 		return ERR_CAST(inode);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/super.c
@@ -57,6 +57,7 @@
 #include <linux/crc-itu-t.h>
 #include <linux/log2.h>
 #include <asm/byteorder.h>
+#include <linux/iversion.h>
 
 #include "udf_sb.h"
 #include "udf_i.h"
@@ -85,6 +86,13 @@
 #define UDF_MAX_LVID_NESTING 1000
 
 enum { UDF_MAX_LINKS = 0xffff };
+/*
+ * We limit filesize to 4TB. This is arbitrary as the on-disk format supports
+ * more but because the file space is described by a linked list of extents,
+ * each of which can have at most 1GB, the creation and handling of extents
+ * gets unusably slow beyond certain point...
+ */
+#define UDF_MAX_FILESIZE (1ULL << 42)
 
 /* These are the "meat" - everything else is stuffing */
 static int udf_fill_super(struct super_block *, void *, int);
@@ -146,9 +154,11 @@
 	ei->i_next_alloc_goal = 0;
 	ei->i_strat4096 = 0;
 	ei->i_streamdir = 0;
+	ei->i_hidden = 0;
 	init_rwsem(&ei->i_data_sem);
 	ei->cached_extent.lstart = -1;
 	spin_lock_init(&ei->i_extent_cache_lock);
+	inode_set_iversion(&ei->vfs_inode, 1);
 
 	return &ei->vfs_inode;
 }
@@ -263,7 +273,8 @@
 	int nr_groups = bitmap->s_nr_groups;
 
 	for (i = 0; i < nr_groups; i++)
-		brelse(bitmap->s_block_bitmap[i]);
+		if (!IS_ERR_OR_NULL(bitmap->s_block_bitmap[i]))
+			brelse(bitmap->s_block_bitmap[i]);
 
 	kvfree(bitmap);
 }
@@ -1073,12 +1084,19 @@
 	struct udf_part_map *map;
 	struct udf_sb_info *sbi = UDF_SB(sb);
 	struct partitionHeaderDesc *phd;
+	u32 sum;
 	int err;
 
 	map = &sbi->s_partmaps[p_index];
 
 	map->s_partition_len = le32_to_cpu(p->partitionLength); /* blocks */
 	map->s_partition_root = le32_to_cpu(p->partitionStartingLocation);
+	if (check_add_overflow(map->s_partition_root, map->s_partition_len,
+			       &sum)) {
+		udf_err(sb, "Partition %d has invalid location %u + %u\n",
+			p_index, map->s_partition_root, map->s_partition_len);
+		return -EFSCORRUPTED;
+	}
 
 	if (p->accessType == cpu_to_le32(PD_ACCESS_TYPE_READ_ONLY))
 		map->s_partition_flags |= UDF_PART_FLAG_READ_ONLY;
@@ -1134,6 +1152,14 @@
 		bitmap->s_extPosition = le32_to_cpu(
 				phd->unallocSpaceBitmap.extPosition);
 		map->s_partition_flags |= UDF_PART_FLAG_UNALLOC_BITMAP;
+		/* Check whether math over bitmap won't overflow. */
+		if (check_add_overflow(map->s_partition_len,
+				       sizeof(struct spaceBitmapDesc) << 3,
+				       &sum)) {
+			udf_err(sb, "Partition %d is too long (%u)\n", p_index,
+				map->s_partition_len);
+			return -EFSCORRUPTED;
+		}
 		udf_debug("unallocSpaceBitmap (part %d) @ %u\n",
 			  p_index, bitmap->s_extPosition);
 	}
@@ -2298,7 +2324,7 @@
 		ret = -ENOMEM;
 		goto error_out;
 	}
-	sb->s_maxbytes = MAX_LFS_FILESIZE;
+	sb->s_maxbytes = UDF_MAX_FILESIZE;
 	sb->s_max_links = UDF_MAX_LINKS;
 	return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/truncate.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/truncate.c
@@ -120,60 +120,42 @@
 
 void udf_discard_prealloc(struct inode *inode)
 {
-	struct extent_position epos = { NULL, 0, {0, 0} };
+	struct extent_position epos = {};
+	struct extent_position prev_epos = {};
 	struct kernel_lb_addr eloc;
 	uint32_t elen;
 	uint64_t lbcount = 0;
 	int8_t etype = -1, netype;
-	int adsize;
 	struct udf_inode_info *iinfo = UDF_I(inode);
+	int bsize = 1 << inode->i_blkbits;
 
 	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB ||
-	    inode->i_size == iinfo->i_lenExtents)
+	    ALIGN(inode->i_size, bsize) == ALIGN(iinfo->i_lenExtents, bsize))
 		return;
 
-	if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_SHORT)
-		adsize = sizeof(struct short_ad);
-	else if (iinfo->i_alloc_type == ICBTAG_FLAG_AD_LONG)
-		adsize = sizeof(struct long_ad);
-	else
-		adsize = 0;
-
 	epos.block = iinfo->i_location;
 
 	/* Find the last extent in the file */
-	while ((netype = udf_next_aext(inode, &epos, &eloc, &elen, 1)) != -1) {
-		etype = netype;
+	while ((netype = udf_next_aext(inode, &epos, &eloc, &elen, 0)) != -1) {
+		brelse(prev_epos.bh);
+		prev_epos = epos;
+		if (prev_epos.bh)
+			get_bh(prev_epos.bh);
+
+		etype = udf_next_aext(inode, &epos, &eloc, &elen, 1);
 		lbcount += elen;
 	}
 	if (etype == (EXT_NOT_RECORDED_ALLOCATED >> 30)) {
-		epos.offset -= adsize;
 		lbcount -= elen;
-		extent_trunc(inode, &epos, &eloc, etype, elen, 0);
-		if (!epos.bh) {
-			iinfo->i_lenAlloc =
-				epos.offset -
-				udf_file_entry_alloc_offset(inode);
-			mark_inode_dirty(inode);
-		} else {
-			struct allocExtDesc *aed =
-				(struct allocExtDesc *)(epos.bh->b_data);
-			aed->lengthAllocDescs =
-				cpu_to_le32(epos.offset -
-					    sizeof(struct allocExtDesc));
-			if (!UDF_QUERY_FLAG(inode->i_sb, UDF_FLAG_STRICT) ||
-			    UDF_SB(inode->i_sb)->s_udfrev >= 0x0201)
-				udf_update_tag(epos.bh->b_data, epos.offset);
-			else
-				udf_update_tag(epos.bh->b_data,
-					       sizeof(struct allocExtDesc));
-			mark_buffer_dirty_inode(epos.bh, inode);
-		}
+		udf_delete_aext(inode, prev_epos);
+		udf_free_blocks(inode->i_sb, inode, &eloc, 0,
+				DIV_ROUND_UP(elen, 1 << inode->i_blkbits));
 	}
 	/* This inode entry is in-memory only and thus we don't have to mark
 	 * the inode dirty */
 	iinfo->i_lenExtents = lbcount;
 	brelse(epos.bh);
+	brelse(prev_epos.bh);
 }
 
 static void udf_update_alloc_ext_desc(struct inode *inode,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/udf_i.h
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/udf_i.h
@@ -44,7 +44,8 @@
 	unsigned		i_use : 1;	/* unallocSpaceEntry */
 	unsigned		i_strat4096 : 1;
 	unsigned		i_streamdir : 1;
-	unsigned		reserved : 25;
+	unsigned		i_hidden : 1;	/* hidden system inode */
+	unsigned		reserved : 24;
 	__u8			*i_data;
 	struct kernel_lb_addr	i_locStreamdir;
 	__u64			i_lenStreams;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/udf_sb.h
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/udf_sb.h
@@ -51,6 +51,8 @@
 #define MF_DUPLICATE_MD		0x01
 #define MF_MIRROR_FE_LOADED	0x02
 
+#define EFSCORRUPTED EUCLEAN
+
 struct udf_meta_data {
 	__u32	s_meta_file_loc;
 	__u32	s_mirror_file_loc;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/udfdecl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/udfdecl.h
@@ -86,11 +86,22 @@
 extern const struct address_space_operations udf_adinicb_aops;
 extern const struct address_space_operations udf_symlink_aops;
 
-struct udf_fileident_bh {
-	struct buffer_head *sbh;
-	struct buffer_head *ebh;
-	int soffset;
-	int eoffset;
+struct udf_fileident_iter {
+	struct inode *dir;		/* Directory we are working with */
+	loff_t pos;			/* Logical position in a dir */
+	struct buffer_head *bh[2];	/* Buffer containing 'pos' and possibly
+					 * next buffer if entry straddles
+					 * blocks */
+	struct kernel_lb_addr eloc;	/* Start of extent containing 'pos' */
+	uint32_t elen;			/* Length of extent containing 'pos' */
+	sector_t loffset;		/* Block offset of 'pos' within above
+					 * extent */
+	struct extent_position epos;	/* Position after the above extent */
+	struct fileIdentDesc fi;	/* Copied directory entry */
+	uint8_t *name;			/* Pointer to entry name */
+	uint8_t *namebuf;		/* Storage for entry name in case
+					 * the name is split between two blocks
+					 */
 };
 
 struct udf_vds_record {
@@ -121,19 +132,12 @@
 					u32 meta_file_loc, u32 partition_num);
 
 /* namei.c */
-extern int udf_write_fi(struct inode *inode, struct fileIdentDesc *,
-			struct fileIdentDesc *, struct udf_fileident_bh *,
-			uint8_t *, uint8_t *);
 static inline unsigned int udf_dir_entry_len(struct fileIdentDesc *cfi)
 {
 	return ALIGN(sizeof(struct fileIdentDesc) +
 		le16_to_cpu(cfi->lengthOfImpUse) + cfi->lengthFileIdent,
 		UDF_NAME_PAD);
 }
-static inline uint8_t *udf_get_fi_ident(struct fileIdentDesc *fi)
-{
-	return ((uint8_t *)(fi + 1)) + le16_to_cpu(fi->lengthOfImpUse);
-}
 
 /* file.c */
 extern long udf_ioctl(struct file *, unsigned int, unsigned long);
@@ -151,8 +155,6 @@
 	return __udf_iget(sb, ino, false);
 }
 extern int udf_expand_file_adinicb(struct inode *);
-extern struct buffer_head *udf_expand_dir_adinicb(struct inode *inode,
-						  udf_pblk_t *block, int *err);
 extern struct buffer_head *udf_bread(struct inode *inode, udf_pblk_t block,
 				      int create, int *err);
 extern int udf_setsize(struct inode *, loff_t);
@@ -243,14 +245,13 @@
 				 uint16_t partition, uint32_t goal, int *err);
 
 /* directory.c */
-extern struct fileIdentDesc *udf_fileident_read(struct inode *, loff_t *,
-						struct udf_fileident_bh *,
-						struct fileIdentDesc *,
-						struct extent_position *,
-						struct kernel_lb_addr *, uint32_t *,
-						sector_t *);
-extern struct fileIdentDesc *udf_get_fileident(void *buffer, int bufsize,
-					       int *offset);
+int udf_fiiter_init(struct udf_fileident_iter *iter, struct inode *dir,
+		    loff_t pos);
+int udf_fiiter_advance(struct udf_fileident_iter *iter);
+void udf_fiiter_release(struct udf_fileident_iter *iter);
+void udf_fiiter_write_fi(struct udf_fileident_iter *iter, uint8_t *impuse);
+void udf_fiiter_update_elen(struct udf_fileident_iter *iter, uint32_t new_elen);
+int udf_fiiter_append_blk(struct udf_fileident_iter *iter);
 extern struct long_ad *udf_get_filelongad(uint8_t *, int, uint32_t *, int);
 extern struct short_ad *udf_get_fileshortad(uint8_t *, int, uint32_t *, int);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/udftime.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/udftime.c
@@ -60,13 +60,18 @@
 	dest->tv_sec = mktime64(year, src.month, src.day, src.hour, src.minute,
 			src.second);
 	dest->tv_sec -= offset * 60;
-	dest->tv_nsec = 1000 * (src.centiseconds * 10000 +
-			src.hundredsOfMicroseconds * 100 + src.microseconds);
+
 	/*
 	 * Sanitize nanosecond field since reportedly some filesystems are
 	 * recorded with bogus sub-second values.
 	 */
-	dest->tv_nsec %= NSEC_PER_SEC;
+	if (src.centiseconds < 100 && src.hundredsOfMicroseconds < 100 &&
+	    src.microseconds < 100) {
+		dest->tv_nsec = 1000 * (src.centiseconds * 10000 +
+			src.hundredsOfMicroseconds * 100 + src.microseconds);
+	} else {
+		dest->tv_nsec = 0;
+	}
 }
 
 void
--- linux-xilinx-zynqmp-5.15.0.orig/fs/udf/unicode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/udf/unicode.c
@@ -247,7 +247,7 @@
 	}
 
 	if (translate) {
-		if (str_o_len <= 2 && str_o[0] == '.' &&
+		if (str_o_len > 0 && str_o_len <= 2 && str_o[0] == '.' &&
 		    (str_o_len == 1 || str_o[1] == '.'))
 			needsCRC = 1;
 		if (needsCRC) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ufs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/ufs/super.c
@@ -1239,11 +1239,7 @@
 	else
 		uspi->s_apbshift = uspi->s_bshift - 2;
 
-	uspi->s_2apbshift = uspi->s_apbshift * 2;
-	uspi->s_3apbshift = uspi->s_apbshift * 3;
 	uspi->s_apb = 1 << uspi->s_apbshift;
-	uspi->s_2apb = 1 << uspi->s_2apbshift;
-	uspi->s_3apb = 1 << uspi->s_3apbshift;
 	uspi->s_apbmask = uspi->s_apb - 1;
 	uspi->s_nspfshift = uspi->s_fshift - UFS_SECTOR_BITS;
 	uspi->s_nspb = uspi->s_nspf << uspi->s_fpbshift;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/ufs/ufs_fs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/ufs/ufs_fs.h
@@ -775,12 +775,8 @@
 
 	__u32	s_fpbmask;	/* fragments per block mask */
 	__u32	s_apb;		/* address per block */
-	__u32	s_2apb;		/* address per block^2 */
-	__u32	s_3apb;		/* address per block^3 */
 	__u32	s_apbmask;	/* address per block mask */
 	__u32	s_apbshift;	/* address per block shift */
-	__u32	s_2apbshift;	/* address per block shift * 2 */
-	__u32	s_3apbshift;	/* address per block shift * 3 */
 	__u32	s_nspfshift;	/* number of sector per fragment shift */
 	__u32	s_nspb;		/* number of sector per block */
 	__u32	s_inopf;	/* inodes per fragment */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/userfaultfd.c
+++ linux-xilinx-zynqmp-5.15.0/fs/userfaultfd.c
@@ -982,7 +982,7 @@
 	int fd;
 
 	fd = anon_inode_getfd_secure("[userfaultfd]", &userfaultfd_fops, new,
-			O_RDWR | (new->flags & UFFD_SHARED_FCNTL_FLAGS), inode);
+			O_RDONLY | (new->flags & UFFD_SHARED_FCNTL_FLAGS), inode);
 	if (fd < 0)
 		return fd;
 
@@ -1935,7 +1935,7 @@
 		goto out;
 	features = uffdio_api.features;
 	ret = -EINVAL;
-	if (uffdio_api.api != UFFD_API || (features & ~UFFD_API_FEATURES))
+	if (uffdio_api.api != UFFD_API)
 		goto err_out;
 	ret = -EPERM;
 	if ((features & UFFD_FEATURE_EVENT_FORK) && !capable(CAP_SYS_PTRACE))
@@ -1949,6 +1949,11 @@
 #ifndef CONFIG_HAVE_ARCH_USERFAULTFD_WP
 	uffdio_api.features &= ~UFFD_FEATURE_PAGEFAULT_FLAG_WP;
 #endif
+
+	ret = -EINVAL;
+	if (features & ~uffdio_api.features)
+		goto err_out;
+
 	uffdio_api.ioctls = UFFD_API_IOCTLS;
 	ret = -EFAULT;
 	if (copy_to_user(buf, &uffdio_api, sizeof(uffdio_api)))
@@ -2097,7 +2102,7 @@
 	mmgrab(ctx->mm);
 
 	fd = anon_inode_getfd_secure("[userfaultfd]", &userfaultfd_fops, ctx,
-			O_RDWR | (flags & UFFD_SHARED_FCNTL_FLAGS), NULL);
+			O_RDONLY | (flags & UFFD_SHARED_FCNTL_FLAGS), NULL);
 	if (fd < 0) {
 		mmdrop(ctx->mm);
 		kmem_cache_free(userfaultfd_ctx_cachep, ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/vboxsf/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/vboxsf/super.c
@@ -21,7 +21,8 @@
 
 #define VBOXSF_SUPER_MAGIC 0x786f4256 /* 'VBox' little endian */
 
-static const unsigned char VBSF_MOUNT_SIGNATURE[4] = "\000\377\376\375";
+static const unsigned char VBSF_MOUNT_SIGNATURE[4] = { '\000', '\377', '\376',
+						       '\375' };
 
 static int follow_symlinks;
 module_param(follow_symlinks, int, 0444);
@@ -151,7 +152,7 @@
 		if (!sbi->nls) {
 			vbg_err("vboxsf: Count not load '%s' nls\n", nls_name);
 			err = -EINVAL;
-			goto fail_free;
+			goto fail_destroy_idr;
 		}
 	}
 
@@ -224,6 +225,7 @@
 		ida_simple_remove(&vboxsf_bdi_ida, sbi->bdi_id);
 	if (sbi->nls)
 		unload_nls(sbi->nls);
+fail_destroy_idr:
 	idr_destroy(&sbi->ino_idr);
 	kfree(sbi);
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/verity/enable.c
+++ linux-xilinx-zynqmp-5.15.0/fs/verity/enable.c
@@ -391,25 +391,27 @@
 		goto out_drop_write;
 
 	err = enable_verity(filp, &arg);
-	if (err)
-		goto out_allow_write_access;
 
 	/*
-	 * Some pages of the file may have been evicted from pagecache after
-	 * being used in the Merkle tree construction, then read into pagecache
-	 * again by another process reading from the file concurrently.  Since
-	 * these pages didn't undergo verification against the file digest which
-	 * fs-verity now claims to be enforcing, we have to wipe the pagecache
-	 * to ensure that all future reads are verified.
+	 * We no longer drop the inode's pagecache after enabling verity.  This
+	 * used to be done to try to avoid a race condition where pages could be
+	 * evicted after being used in the Merkle tree construction, then
+	 * re-instantiated by a concurrent read.  Such pages are unverified, and
+	 * the backing storage could have filled them with different content, so
+	 * they shouldn't be used to fulfill reads once verity is enabled.
+	 *
+	 * But, dropping the pagecache has a big performance impact, and it
+	 * doesn't fully solve the race condition anyway.  So for those reasons,
+	 * and also because this race condition isn't very important relatively
+	 * speaking (especially for small-ish files, where the chance of a page
+	 * being used, evicted, *and* re-instantiated all while enabling verity
+	 * is quite small), we no longer drop the inode's pagecache.
 	 */
-	filemap_write_and_wait(inode->i_mapping);
-	invalidate_inode_pages2(inode->i_mapping);
 
 	/*
 	 * allow_write_access() is needed to pair with deny_write_access().
 	 * Regardless, the filesystem won't allow writing to verity files.
 	 */
-out_allow_write_access:
 	allow_write_access(filp);
 out_drop_write:
 	mnt_drop_write_file(filp);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/verity/signature.c
+++ linux-xilinx-zynqmp-5.15.0/fs/verity/signature.c
@@ -54,6 +54,22 @@
 		return 0;
 	}
 
+	if (fsverity_keyring->keys.nr_leaves_on_tree == 0) {
+		/*
+		 * The ".fs-verity" keyring is empty, due to builtin signatures
+		 * being supported by the kernel but not actually being used.
+		 * In this case, verify_pkcs7_signature() would always return an
+		 * error, usually ENOKEY.  It could also be EBADMSG if the
+		 * PKCS#7 is malformed, but that isn't very important to
+		 * distinguish.  So, just skip to ENOKEY to avoid the attack
+		 * surface of the PKCS#7 parser, which would otherwise be
+		 * reachable by any task able to execute FS_IOC_ENABLE_VERITY.
+		 */
+		fsverity_err(inode,
+			     "fs-verity keyring is empty, rejecting signed file!");
+		return -ENOKEY;
+	}
+
 	d = kzalloc(sizeof(*d) + hash_alg->digest_size, GFP_KERNEL);
 	if (!d)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/verity/verify.c
+++ linux-xilinx-zynqmp-5.15.0/fs/verity/verify.c
@@ -279,15 +279,15 @@
 int __init fsverity_init_workqueue(void)
 {
 	/*
-	 * Use an unbound workqueue to allow bios to be verified in parallel
-	 * even when they happen to complete on the same CPU.  This sacrifices
-	 * locality, but it's worthwhile since hashing is CPU-intensive.
+	 * Use a high-priority workqueue to prioritize verification work, which
+	 * blocks reads from completing, over regular application tasks.
 	 *
-	 * Also use a high-priority workqueue to prioritize verification work,
-	 * which blocks reads from completing, over regular application tasks.
+	 * For performance reasons, don't use an unbound workqueue.  Using an
+	 * unbound workqueue for crypto operations causes excessive scheduler
+	 * latency on ARM64.
 	 */
 	fsverity_read_workqueue = alloc_workqueue("fsverity_read_queue",
-						  WQ_UNBOUND | WQ_HIGHPRI,
+						  WQ_HIGHPRI,
 						  num_online_cpus());
 	if (!fsverity_read_workqueue)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xattr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xattr.c
@@ -25,6 +25,8 @@
 
 #include <linux/uaccess.h>
 
+#include "internal.h"
+
 static const char *
 strcmp_prefix(const char *a, const char *a_prefix)
 {
@@ -237,6 +239,7 @@
 
 	return error;
 }
+EXPORT_SYMBOL_GPL(__vfs_setxattr_noperm);
 
 /**
  * __vfs_setxattr_locked - set an extended attribute while holding the inode
@@ -384,6 +387,7 @@
 	*xattr_value = value;
 	return error;
 }
+EXPORT_SYMBOL_GPL(vfs_getxattr_alloc);
 
 ssize_t
 __vfs_getxattr(struct dentry *dentry, struct inode *inode, const char *name,
@@ -471,6 +475,34 @@
 EXPORT_SYMBOL(__vfs_removexattr);
 
 /**
+ *  __vfs_removexattr_noperm - perform removexattr operation without
+ *  performing permission checks.
+ *
+ *  @dentry - object to perform setxattr on
+ *  @name - xattr name to set
+ *
+ *  returns the result of the internal setxattr or setsecurity operations.
+ *
+ *  This function requires the caller to lock the inode's i_mutex before it
+ *  is executed. It also assumes that the caller will make the appropriate
+ *  permission checks.
+ */
+int
+__vfs_removexattr_noperm(struct user_namespace *mnt_userns,
+			 struct dentry *dentry, const char *name)
+{
+	int error;
+
+	error =__vfs_removexattr(mnt_userns, dentry, name);
+	if (!error) {
+		fsnotify_xattr(dentry);
+		evm_inode_post_removexattr(dentry, name);
+	}
+	return error;
+}
+EXPORT_SYMBOL_GPL(__vfs_removexattr_noperm);
+
+/**
  * __vfs_removexattr_locked - set an extended attribute while holding the inode
  * lock
  *
@@ -500,12 +532,7 @@
 	if (error)
 		goto out;
 
-	error = __vfs_removexattr(mnt_userns, dentry, name);
-
-	if (!error) {
-		fsnotify_xattr(dentry);
-		evm_inode_post_removexattr(dentry, name);
-	}
+	error = __vfs_removexattr_noperm(mnt_userns, dentry, name);
 
 out:
 	return error;
@@ -539,43 +566,76 @@
 /*
  * Extended attribute SET operations
  */
-static long
-setxattr(struct user_namespace *mnt_userns, struct dentry *d,
-	 const char __user *name, const void __user *value, size_t size,
-	 int flags)
+
+int setxattr_copy(const char __user *name, struct xattr_ctx *ctx)
 {
 	int error;
-	void *kvalue = NULL;
-	char kname[XATTR_NAME_MAX + 1];
 
-	if (flags & ~(XATTR_CREATE|XATTR_REPLACE))
+	if (ctx->flags & ~(XATTR_CREATE|XATTR_REPLACE))
 		return -EINVAL;
 
-	error = strncpy_from_user(kname, name, sizeof(kname));
-	if (error == 0 || error == sizeof(kname))
-		error = -ERANGE;
+	error = strncpy_from_user(ctx->kname->name, name,
+				sizeof(ctx->kname->name));
+	if (error == 0 || error == sizeof(ctx->kname->name))
+		return  -ERANGE;
 	if (error < 0)
 		return error;
 
-	if (size) {
-		if (size > XATTR_SIZE_MAX)
+	error = 0;
+	if (ctx->size) {
+		if (ctx->size > XATTR_SIZE_MAX)
 			return -E2BIG;
-		kvalue = kvmalloc(size, GFP_KERNEL);
-		if (!kvalue)
-			return -ENOMEM;
-		if (copy_from_user(kvalue, value, size)) {
-			error = -EFAULT;
-			goto out;
+
+		ctx->kvalue = vmemdup_user(ctx->cvalue, ctx->size);
+		if (IS_ERR(ctx->kvalue)) {
+			error = PTR_ERR(ctx->kvalue);
+			ctx->kvalue = NULL;
 		}
-		if ((strcmp(kname, XATTR_NAME_POSIX_ACL_ACCESS) == 0) ||
-		    (strcmp(kname, XATTR_NAME_POSIX_ACL_DEFAULT) == 0))
-			posix_acl_fix_xattr_from_user(mnt_userns, kvalue, size);
 	}
 
-	error = vfs_setxattr(mnt_userns, d, kname, kvalue, size, flags);
-out:
-	kvfree(kvalue);
+	return error;
+}
+
+static void setxattr_convert(struct user_namespace *mnt_userns,
+			     struct dentry *d, struct xattr_ctx *ctx)
+{
+	if (ctx->size &&
+		((strcmp(ctx->kname->name, XATTR_NAME_POSIX_ACL_ACCESS) == 0) ||
+		(strcmp(ctx->kname->name, XATTR_NAME_POSIX_ACL_DEFAULT) == 0)))
+		posix_acl_fix_xattr_from_user(mnt_userns, d_inode(d),
+						ctx->kvalue, ctx->size);
+}
+
+int do_setxattr(struct user_namespace *mnt_userns, struct dentry *dentry,
+		struct xattr_ctx *ctx)
+{
+	setxattr_convert(mnt_userns, dentry, ctx);
+	return vfs_setxattr(mnt_userns, dentry, ctx->kname->name,
+			ctx->kvalue, ctx->size, ctx->flags);
+}
+
+static long
+setxattr(struct user_namespace *mnt_userns, struct dentry *d,
+	const char __user *name, const void __user *value, size_t size,
+	int flags)
+{
+	struct xattr_name kname;
+	struct xattr_ctx ctx = {
+		.cvalue   = value,
+		.kvalue   = NULL,
+		.size     = size,
+		.kname    = &kname,
+		.flags    = flags,
+	};
+	int error;
+
+	error = setxattr_copy(name, &ctx);
+	if (error)
+		return error;
+
+	error = do_setxattr(mnt_userns, d, &ctx);
 
+	kvfree(ctx.kvalue);
 	return error;
 }
 
@@ -667,7 +727,8 @@
 	if (error > 0) {
 		if ((strcmp(kname, XATTR_NAME_POSIX_ACL_ACCESS) == 0) ||
 		    (strcmp(kname, XATTR_NAME_POSIX_ACL_DEFAULT) == 0))
-			posix_acl_fix_xattr_to_user(mnt_userns, kvalue, error);
+			posix_acl_fix_xattr_to_user(mnt_userns, d_inode(d),
+						    kvalue, error);
 		if (size && copy_to_user(value, kvalue, error))
 			error = -EFAULT;
 	} else if (error == -ERANGE && size >= XATTR_SIZE_MAX) {
@@ -1083,7 +1144,7 @@
 ssize_t simple_xattr_list(struct inode *inode, struct simple_xattrs *xattrs,
 			  char *buffer, size_t size)
 {
-	bool trusted = capable(CAP_SYS_ADMIN);
+	bool trusted = ns_capable_noaudit(&init_user_ns, CAP_SYS_ADMIN);
 	struct simple_xattr *xattr;
 	ssize_t remaining_size = size;
 	int err = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_ag.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_ag.c
@@ -173,7 +173,6 @@
 	struct xfs_perag *pag = container_of(head, struct xfs_perag, rcu_head);
 
 	ASSERT(!delayed_work_pending(&pag->pag_blockgc_work));
-	ASSERT(atomic_read(&pag->pag_ref) == 0);
 	kmem_free(pag);
 }
 
@@ -192,7 +191,7 @@
 		pag = radix_tree_delete(&mp->m_perag_tree, agno);
 		spin_unlock(&mp->m_perag_lock);
 		ASSERT(pag);
-		ASSERT(atomic_read(&pag->pag_ref) == 0);
+		XFS_IS_CORRUPT(pag->pag_mount, atomic_read(&pag->pag_ref) != 0);
 
 		cancel_delayed_work_sync(&pag->pag_blockgc_work);
 		xfs_iunlink_destroy(pag);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_ag.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_ag.h
@@ -116,23 +116,29 @@
 
 /*
  * Perag iteration APIs
- *
- * XXX: for_each_perag_range() usage really needs an iterator to clean up when
- * we terminate at end_agno because we may have taken a reference to the perag
- * beyond end_agno. Right now callers have to be careful to catch and clean that
- * up themselves. This is not necessary for the callers of for_each_perag() and
- * for_each_perag_from() because they terminate at sb_agcount where there are
- * no perag structures in tree beyond end_agno.
  */
-#define for_each_perag_range(mp, next_agno, end_agno, pag) \
-	for ((pag) = xfs_perag_get((mp), (next_agno)); \
-		(pag) != NULL && (next_agno) <= (end_agno); \
-		(next_agno) = (pag)->pag_agno + 1, \
-		xfs_perag_put(pag), \
-		(pag) = xfs_perag_get((mp), (next_agno)))
+static inline struct xfs_perag *
+xfs_perag_next(
+	struct xfs_perag	*pag,
+	xfs_agnumber_t		*agno,
+	xfs_agnumber_t		end_agno)
+{
+	struct xfs_mount	*mp = pag->pag_mount;
 
-#define for_each_perag_from(mp, next_agno, pag) \
-	for_each_perag_range((mp), (next_agno), (mp)->m_sb.sb_agcount, (pag))
+	*agno = pag->pag_agno + 1;
+	xfs_perag_put(pag);
+	if (*agno > end_agno)
+		return NULL;
+	return xfs_perag_get(mp, *agno);
+}
+
+#define for_each_perag_range(mp, agno, end_agno, pag) \
+	for ((pag) = xfs_perag_get((mp), (agno)); \
+		(pag) != NULL; \
+		(pag) = xfs_perag_next((pag), &(agno), (end_agno)))
+
+#define for_each_perag_from(mp, agno, pag) \
+	for_each_perag_range((mp), (agno), (mp)->m_sb.sb_agcount - 1, (pag))
 
 
 #define for_each_perag(mp, agno, pag) \
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_attr.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_attr.c
@@ -1077,21 +1077,18 @@
 
 	state = xfs_da_state_alloc(args);
 	if (statep != NULL)
-		*statep = NULL;
+		*statep = state;
 
 	/*
 	 * Search to see if name exists, and get back a pointer to it.
 	 */
 	error = xfs_da3_node_lookup_int(state, &retval);
-	if (error) {
-		xfs_da_state_free(state);
-		return error;
-	}
+	if (error)
+		retval = error;
 
-	if (statep != NULL)
-		*statep = state;
-	else
+	if (!statep)
 		xfs_da_state_free(state);
+
 	return retval;
 }
 
@@ -1112,7 +1109,7 @@
 	 */
 	retval = xfs_attr_node_hasname(args, &dac->da_state);
 	if (retval != -ENOATTR && retval != -EEXIST)
-		return retval;
+		goto error;
 
 	if (retval == -ENOATTR && (args->attr_flags & XATTR_REPLACE))
 		goto error;
@@ -1337,7 +1334,7 @@
 
 	error = xfs_attr_node_hasname(args, state);
 	if (error != -EEXIST)
-		return error;
+		goto out;
 	error = 0;
 
 	ASSERT((*state)->path.blk[(*state)->path.active - 1].bp != NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_btree.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_btree.c
@@ -52,6 +52,71 @@
 }
 
 /*
+ * These sibling pointer checks are optimised for null sibling pointers. This
+ * happens a lot, and we don't need to byte swap at runtime if the sibling
+ * pointer is NULL.
+ *
+ * These are explicitly marked at inline because the cost of calling them as
+ * functions instead of inlining them is about 36 bytes extra code per call site
+ * on x86-64. Yes, gcc-11 fails to inline them, and explicit inlining of these
+ * two sibling check functions reduces the compiled code size by over 300
+ * bytes.
+ */
+static inline xfs_failaddr_t
+xfs_btree_check_lblock_siblings(
+	struct xfs_mount	*mp,
+	struct xfs_btree_cur	*cur,
+	int			level,
+	xfs_fsblock_t		fsb,
+	__be64			dsibling)
+{
+	xfs_fsblock_t		sibling;
+
+	if (dsibling == cpu_to_be64(NULLFSBLOCK))
+		return NULL;
+
+	sibling = be64_to_cpu(dsibling);
+	if (sibling == fsb)
+		return __this_address;
+	if (level >= 0) {
+		if (!xfs_btree_check_lptr(cur, sibling, level + 1))
+			return __this_address;
+	} else {
+		if (!xfs_verify_fsbno(mp, sibling))
+			return __this_address;
+	}
+
+	return NULL;
+}
+
+static inline xfs_failaddr_t
+xfs_btree_check_sblock_siblings(
+	struct xfs_mount	*mp,
+	struct xfs_btree_cur	*cur,
+	int			level,
+	xfs_agnumber_t		agno,
+	xfs_agblock_t		agbno,
+	__be32			dsibling)
+{
+	xfs_agblock_t		sibling;
+
+	if (dsibling == cpu_to_be32(NULLAGBLOCK))
+		return NULL;
+
+	sibling = be32_to_cpu(dsibling);
+	if (sibling == agbno)
+		return __this_address;
+	if (level >= 0) {
+		if (!xfs_btree_check_sptr(cur, sibling, level + 1))
+			return __this_address;
+	} else {
+		if (!xfs_verify_agbno(mp, agno, sibling))
+			return __this_address;
+	}
+	return NULL;
+}
+
+/*
  * Check a long btree block header.  Return the address of the failing check,
  * or NULL if everything is ok.
  */
@@ -65,6 +130,8 @@
 	struct xfs_mount	*mp = cur->bc_mp;
 	xfs_btnum_t		btnum = cur->bc_btnum;
 	int			crc = xfs_has_crc(mp);
+	xfs_failaddr_t		fa;
+	xfs_fsblock_t		fsb = NULLFSBLOCK;
 
 	if (crc) {
 		if (!uuid_equal(&block->bb_u.l.bb_uuid, &mp->m_sb.sb_meta_uuid))
@@ -83,16 +150,16 @@
 	if (be16_to_cpu(block->bb_numrecs) >
 	    cur->bc_ops->get_maxrecs(cur, level))
 		return __this_address;
-	if (block->bb_u.l.bb_leftsib != cpu_to_be64(NULLFSBLOCK) &&
-	    !xfs_btree_check_lptr(cur, be64_to_cpu(block->bb_u.l.bb_leftsib),
-			level + 1))
-		return __this_address;
-	if (block->bb_u.l.bb_rightsib != cpu_to_be64(NULLFSBLOCK) &&
-	    !xfs_btree_check_lptr(cur, be64_to_cpu(block->bb_u.l.bb_rightsib),
-			level + 1))
-		return __this_address;
 
-	return NULL;
+	if (bp)
+		fsb = XFS_DADDR_TO_FSB(mp, xfs_buf_daddr(bp));
+
+	fa = xfs_btree_check_lblock_siblings(mp, cur, level, fsb,
+			block->bb_u.l.bb_leftsib);
+	if (!fa)
+		fa = xfs_btree_check_lblock_siblings(mp, cur, level, fsb,
+				block->bb_u.l.bb_rightsib);
+	return fa;
 }
 
 /* Check a long btree block header. */
@@ -130,6 +197,9 @@
 	struct xfs_mount	*mp = cur->bc_mp;
 	xfs_btnum_t		btnum = cur->bc_btnum;
 	int			crc = xfs_has_crc(mp);
+	xfs_failaddr_t		fa;
+	xfs_agblock_t		agbno = NULLAGBLOCK;
+	xfs_agnumber_t		agno = NULLAGNUMBER;
 
 	if (crc) {
 		if (!uuid_equal(&block->bb_u.s.bb_uuid, &mp->m_sb.sb_meta_uuid))
@@ -146,16 +216,18 @@
 	if (be16_to_cpu(block->bb_numrecs) >
 	    cur->bc_ops->get_maxrecs(cur, level))
 		return __this_address;
-	if (block->bb_u.s.bb_leftsib != cpu_to_be32(NULLAGBLOCK) &&
-	    !xfs_btree_check_sptr(cur, be32_to_cpu(block->bb_u.s.bb_leftsib),
-			level + 1))
-		return __this_address;
-	if (block->bb_u.s.bb_rightsib != cpu_to_be32(NULLAGBLOCK) &&
-	    !xfs_btree_check_sptr(cur, be32_to_cpu(block->bb_u.s.bb_rightsib),
-			level + 1))
-		return __this_address;
 
-	return NULL;
+	if (bp) {
+		agbno = xfs_daddr_to_agbno(mp, xfs_buf_daddr(bp));
+		agno = xfs_daddr_to_agno(mp, xfs_buf_daddr(bp));
+	}
+
+	fa = xfs_btree_check_sblock_siblings(mp, cur, level, agno, agbno,
+			block->bb_u.s.bb_leftsib);
+	if (!fa)
+		fa = xfs_btree_check_sblock_siblings(mp, cur, level, agno,
+				 agbno, block->bb_u.s.bb_rightsib);
+	return fa;
 }
 
 /* Check a short btree block header. */
@@ -373,8 +445,14 @@
 			break;
 	}
 
+	/*
+	 * If we are doing a BMBT update, the number of unaccounted blocks
+	 * allocated during this cursor life time should be zero. If it's not
+	 * zero, then we should be shut down or on our way to shutdown due to
+	 * cancelling a dirty transaction on error.
+	 */
 	ASSERT(cur->bc_btnum != XFS_BTNUM_BMAP || cur->bc_ino.allocated == 0 ||
-	       xfs_is_shutdown(cur->bc_mp));
+	       xfs_is_shutdown(cur->bc_mp) || error != 0);
 	if (unlikely(cur->bc_flags & XFS_BTREE_STAGING))
 		kmem_free(cur->bc_ops);
 	if (!(cur->bc_flags & XFS_BTREE_LONG_PTRS) && cur->bc_ag.pag)
@@ -3188,7 +3266,7 @@
 	struct xfs_btree_block	*block;	/* btree block */
 	struct xfs_buf		*bp;	/* buffer for block */
 	union xfs_btree_ptr	nptr;	/* new block ptr */
-	struct xfs_btree_cur	*ncur;	/* new btree cursor */
+	struct xfs_btree_cur	*ncur = NULL;	/* new btree cursor */
 	union xfs_btree_key	nkey;	/* new block key */
 	union xfs_btree_key	*lkey;
 	int			optr;	/* old key/record index */
@@ -3268,7 +3346,7 @@
 #ifdef DEBUG
 	error = xfs_btree_check_block(cur, block, level, bp);
 	if (error)
-		return error;
+		goto error0;
 #endif
 
 	/*
@@ -3288,7 +3366,7 @@
 		for (i = numrecs - ptr; i >= 0; i--) {
 			error = xfs_btree_debug_check_ptr(cur, pp, i, level);
 			if (error)
-				return error;
+				goto error0;
 		}
 
 		xfs_btree_shift_keys(cur, kp, 1, numrecs - ptr + 1);
@@ -3335,14 +3413,31 @@
 	xfs_btree_log_block(cur, bp, XFS_BB_NUMRECS);
 
 	/*
-	 * If we just inserted into a new tree block, we have to
-	 * recalculate nkey here because nkey is out of date.
+	 * Update btree keys to reflect the newly added record or keyptr.
+	 * There are three cases here to be aware of.  Normally, all we have to
+	 * do is walk towards the root, updating keys as necessary.
 	 *
-	 * Otherwise we're just updating an existing block (having shoved
-	 * some records into the new tree block), so use the regular key
-	 * update mechanism.
+	 * If the caller had us target a full block for the insertion, we dealt
+	 * with that by calling the _make_block_unfull function.  If the
+	 * "make unfull" function splits the block, it'll hand us back the key
+	 * and pointer of the new block.  We haven't yet added the new block to
+	 * the next level up, so if we decide to add the new record to the new
+	 * block (bp->b_bn != old_bn), we have to update the caller's pointer
+	 * so that the caller adds the new block with the correct key.
+	 *
+	 * However, there is a third possibility-- if the selected block is the
+	 * root block of an inode-rooted btree and cannot be expanded further,
+	 * the "make unfull" function moves the root block contents to a new
+	 * block and updates the root block to point to the new block.  In this
+	 * case, no block pointer is passed back because the block has already
+	 * been added to the btree.  In this case, we need to use the regular
+	 * key update function, just like the first case.  This is critical for
+	 * overlapping btrees, because the high key must be updated to reflect
+	 * the entire tree, not just the subtree accessible through the first
+	 * child of the root (which is now two levels down from the root).
 	 */
-	if (bp && xfs_buf_daddr(bp) != old_bn) {
+	if (!xfs_btree_ptr_is_null(cur, &nptr) &&
+	    bp && xfs_buf_daddr(bp) != old_bn) {
 		xfs_btree_get_keys(cur, block, lkey);
 	} else if (xfs_btree_needs_key_update(cur, optr)) {
 		error = xfs_btree_update_keys(cur, level);
@@ -3373,6 +3468,8 @@
 	return 0;
 
 error0:
+	if (ncur)
+		xfs_btree_del_cursor(ncur, error);
 	return error;
 }
 
@@ -4265,6 +4362,21 @@
 	if (xfs_btree_ptr_is_null(cur, &rptr))
 		return -ENOENT;
 
+	/*
+	 * We only visit blocks once in this walk, so we have to avoid the
+	 * internal xfs_btree_lookup_get_block() optimisation where it will
+	 * return the same block without checking if the right sibling points
+	 * back to us and creates a cyclic reference in the btree.
+	 */
+	if (cur->bc_flags & XFS_BTREE_LONG_PTRS) {
+		if (be64_to_cpu(rptr.l) == XFS_DADDR_TO_FSB(cur->bc_mp,
+							xfs_buf_daddr(bp)))
+			return -EFSCORRUPTED;
+	} else {
+		if (be32_to_cpu(rptr.s) == xfs_daddr_to_agbno(cur->bc_mp,
+							xfs_buf_daddr(bp)))
+			return -EFSCORRUPTED;
+	}
 	return xfs_btree_lookup_get_block(cur, level, &rptr, &block);
 }
 
@@ -4439,20 +4551,21 @@
 {
 	struct xfs_mount	*mp = bp->b_mount;
 	struct xfs_btree_block	*block = XFS_BUF_TO_BLOCK(bp);
+	xfs_fsblock_t		fsb;
+	xfs_failaddr_t		fa;
 
 	/* numrecs verification */
 	if (be16_to_cpu(block->bb_numrecs) > max_recs)
 		return __this_address;
 
 	/* sibling pointer verification */
-	if (block->bb_u.l.bb_leftsib != cpu_to_be64(NULLFSBLOCK) &&
-	    !xfs_verify_fsbno(mp, be64_to_cpu(block->bb_u.l.bb_leftsib)))
-		return __this_address;
-	if (block->bb_u.l.bb_rightsib != cpu_to_be64(NULLFSBLOCK) &&
-	    !xfs_verify_fsbno(mp, be64_to_cpu(block->bb_u.l.bb_rightsib)))
-		return __this_address;
-
-	return NULL;
+	fsb = XFS_DADDR_TO_FSB(mp, xfs_buf_daddr(bp));
+	fa = xfs_btree_check_lblock_siblings(mp, NULL, -1, fsb,
+			block->bb_u.l.bb_leftsib);
+	if (!fa)
+		fa = xfs_btree_check_lblock_siblings(mp, NULL, -1, fsb,
+				block->bb_u.l.bb_rightsib);
+	return fa;
 }
 
 /**
@@ -4493,7 +4606,9 @@
 {
 	struct xfs_mount	*mp = bp->b_mount;
 	struct xfs_btree_block	*block = XFS_BUF_TO_BLOCK(bp);
-	xfs_agblock_t		agno;
+	xfs_agnumber_t		agno;
+	xfs_agblock_t		agbno;
+	xfs_failaddr_t		fa;
 
 	/* numrecs verification */
 	if (be16_to_cpu(block->bb_numrecs) > max_recs)
@@ -4501,14 +4616,13 @@
 
 	/* sibling pointer verification */
 	agno = xfs_daddr_to_agno(mp, xfs_buf_daddr(bp));
-	if (block->bb_u.s.bb_leftsib != cpu_to_be32(NULLAGBLOCK) &&
-	    !xfs_verify_agbno(mp, agno, be32_to_cpu(block->bb_u.s.bb_leftsib)))
-		return __this_address;
-	if (block->bb_u.s.bb_rightsib != cpu_to_be32(NULLAGBLOCK) &&
-	    !xfs_verify_agbno(mp, agno, be32_to_cpu(block->bb_u.s.bb_rightsib)))
-		return __this_address;
-
-	return NULL;
+	agbno = xfs_daddr_to_agbno(mp, xfs_buf_daddr(bp));
+	fa = xfs_btree_check_sblock_siblings(mp, NULL, -1, agno, agbno,
+			block->bb_u.s.bb_leftsib);
+	if (!fa)
+		fa = xfs_btree_check_sblock_siblings(mp, NULL, -1, agno, agbno,
+				block->bb_u.s.bb_rightsib);
+	return fa;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_btree_staging.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_btree_staging.c
@@ -662,7 +662,7 @@
 	xfs_btree_bload_ensure_slack(cur, &bbl->node_slack, 1);
 
 	bbl->nr_records = nr_this_level = nr_records;
-	for (cur->bc_nlevels = 1; cur->bc_nlevels < XFS_BTREE_MAXLEVELS;) {
+	for (cur->bc_nlevels = 1; cur->bc_nlevels <= XFS_BTREE_MAXLEVELS;) {
 		uint64_t	level_blocks;
 		uint64_t	dontcare64;
 		unsigned int	level = cur->bc_nlevels - 1;
@@ -724,7 +724,7 @@
 		nr_this_level = level_blocks;
 	}
 
-	if (cur->bc_nlevels == XFS_BTREE_MAXLEVELS)
+	if (cur->bc_nlevels > XFS_BTREE_MAXLEVELS)
 		return -EOVERFLOW;
 
 	bbl->btree_height = cur->bc_nlevels;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_dir2_leaf.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_dir2_leaf.c
@@ -146,6 +146,8 @@
 	xfs_dir2_leaf_tail_t		*ltp;
 	int				stale;
 	int				i;
+	bool				isleaf1 = (hdr->magic == XFS_DIR2_LEAF1_MAGIC ||
+						   hdr->magic == XFS_DIR3_LEAF1_MAGIC);
 
 	ltp = xfs_dir2_leaf_tail_p(geo, leaf);
 
@@ -158,8 +160,7 @@
 		return __this_address;
 
 	/* Leaves and bests don't overlap in leaf format. */
-	if ((hdr->magic == XFS_DIR2_LEAF1_MAGIC ||
-	     hdr->magic == XFS_DIR3_LEAF1_MAGIC) &&
+	if (isleaf1 &&
 	    (char *)&hdr->ents[hdr->count] > (char *)xfs_dir2_leaf_bests_p(ltp))
 		return __this_address;
 
@@ -175,6 +176,10 @@
 		}
 		if (hdr->ents[i].address == cpu_to_be32(XFS_DIR2_NULL_DATAPTR))
 			stale++;
+		if (isleaf1 && xfs_dir2_dataptr_to_db(geo,
+				be32_to_cpu(hdr->ents[i].address)) >=
+				be32_to_cpu(ltp->bestcount))
+			return __this_address;
 	}
 	if (hdr->stale != stale)
 		return __this_address;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_inode_buf.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_inode_buf.c
@@ -337,19 +337,36 @@
 	int			whichfork)
 {
 	uint32_t		di_nextents = XFS_DFORK_NEXTENTS(dip, whichfork);
+	mode_t			mode = be16_to_cpu(dip->di_mode);
+	uint32_t		fork_size = XFS_DFORK_SIZE(dip, mp, whichfork);
+	uint32_t		fork_format = XFS_DFORK_FORMAT(dip, whichfork);
 
-	switch (XFS_DFORK_FORMAT(dip, whichfork)) {
+	/*
+	 * For fork types that can contain local data, check that the fork
+	 * format matches the size of local data contained within the fork.
+	 *
+	 * For all types, check that when the size says the should be in extent
+	 * or btree format, the inode isn't claiming it is in local format.
+	 */
+	if (whichfork == XFS_DATA_FORK) {
+		if (S_ISDIR(mode) || S_ISLNK(mode)) {
+			if (be64_to_cpu(dip->di_size) <= fork_size &&
+			    fork_format != XFS_DINODE_FMT_LOCAL)
+				return __this_address;
+		}
+
+		if (be64_to_cpu(dip->di_size) > fork_size &&
+		    fork_format == XFS_DINODE_FMT_LOCAL)
+			return __this_address;
+	}
+
+	switch (fork_format) {
 	case XFS_DINODE_FMT_LOCAL:
 		/*
-		 * no local regular files yet
+		 * No local regular files yet.
 		 */
-		if (whichfork == XFS_DATA_FORK) {
-			if (S_ISREG(be16_to_cpu(dip->di_mode)))
-				return __this_address;
-			if (be64_to_cpu(dip->di_size) >
-					XFS_DFORK_SIZE(dip, mp, whichfork))
-				return __this_address;
-		}
+		if (S_ISREG(mode) && whichfork == XFS_DATA_FORK)
+			return __this_address;
 		if (di_nextents)
 			return __this_address;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_inode_fork.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_inode_fork.c
@@ -50,8 +50,13 @@
 		mem_size++;
 
 	if (size) {
+		/*
+		 * As we round up the allocation here, we need to ensure the
+		 * bytes we don't copy data into are zeroed because the log
+		 * vectors still copy them into the journal.
+		 */
 		real_size = roundup(mem_size, 4);
-		ifp->if_u1.if_data = kmem_alloc(real_size, KM_NOFS);
+		ifp->if_u1.if_data = kmem_zalloc(real_size, KM_NOFS);
 		memcpy(ifp->if_u1.if_data, data, size);
 		if (zero_terminate)
 			ifp->if_u1.if_data[size] = '\0';
@@ -325,6 +330,7 @@
 	}
 
 	if (error) {
+		xfs_idestroy_fork(ip->i_afp);
 		kmem_cache_free(xfs_ifork_zone, ip->i_afp);
 		ip->i_afp = NULL;
 	}
@@ -500,10 +506,11 @@
 	/*
 	 * For inline data, the underlying buffer must be a multiple of 4 bytes
 	 * in size so that it can be logged and stay on word boundaries.
-	 * We enforce that here.
+	 * We enforce that here, and use __GFP_ZERO to ensure that size
+	 * extensions always zero the unused roundup area.
 	 */
 	ifp->if_u1.if_data = krealloc(ifp->if_u1.if_data, roundup(new_size, 4),
-				      GFP_NOFS | __GFP_NOFAIL);
+				      GFP_NOFS | __GFP_NOFAIL | __GFP_ZERO);
 	ifp->if_bytes = new_size;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_log_recover.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_log_recover.h
@@ -108,12 +108,6 @@
 
 #define ITEM_TYPE(i)	(*(unsigned short *)(i)->ri_buf[0].i_addr)
 
-/*
- * This is the number of entries in the l_buf_cancel_table used during
- * recovery.
- */
-#define	XLOG_BC_TABLE_SIZE	64
-
 #define	XLOG_RECOVER_CRCPASS	0
 #define	XLOG_RECOVER_PASS1	1
 #define	XLOG_RECOVER_PASS2	2
@@ -126,5 +120,13 @@
 		struct xfs_inode **ipp);
 void xlog_recover_release_intent(struct xlog *log, unsigned short intent_type,
 		uint64_t intent_id);
+int xlog_alloc_buf_cancel_table(struct xlog *log);
+void xlog_free_buf_cancel_table(struct xlog *log);
+
+#ifdef DEBUG
+void xlog_check_buf_cancel_table(struct xlog *log);
+#else
+#define xlog_check_buf_cancel_table(log) do { } while (0)
+#endif
 
 #endif	/* __XFS_LOG_RECOVER_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_sb.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_sb.c
@@ -31,18 +31,70 @@
  */
 
 /*
- * We support all XFS versions newer than a v4 superblock with V2 directories.
+ * Check that all the V4 feature bits that the V5 filesystem format requires are
+ * correctly set.
+ */
+static bool
+xfs_sb_validate_v5_features(
+	struct xfs_sb	*sbp)
+{
+	/* We must not have any unknown V4 feature bits set */
+	if (sbp->sb_versionnum & ~XFS_SB_VERSION_OKBITS)
+		return false;
+
+	/*
+	 * The CRC bit is considered an invalid V4 flag, so we have to add it
+	 * manually to the OKBITS mask.
+	 */
+	if (sbp->sb_features2 & ~(XFS_SB_VERSION2_OKBITS |
+				  XFS_SB_VERSION2_CRCBIT))
+		return false;
+
+	/* Now check all the required V4 feature flags are set. */
+
+#define V5_VERS_FLAGS	(XFS_SB_VERSION_NLINKBIT	| \
+			XFS_SB_VERSION_ALIGNBIT		| \
+			XFS_SB_VERSION_LOGV2BIT		| \
+			XFS_SB_VERSION_EXTFLGBIT	| \
+			XFS_SB_VERSION_DIRV2BIT		| \
+			XFS_SB_VERSION_MOREBITSBIT)
+
+#define V5_FEAT_FLAGS	(XFS_SB_VERSION2_LAZYSBCOUNTBIT	| \
+			XFS_SB_VERSION2_ATTR2BIT	| \
+			XFS_SB_VERSION2_PROJID32BIT	| \
+			XFS_SB_VERSION2_CRCBIT)
+
+	if ((sbp->sb_versionnum & V5_VERS_FLAGS) != V5_VERS_FLAGS)
+		return false;
+	if ((sbp->sb_features2 & V5_FEAT_FLAGS) != V5_FEAT_FLAGS)
+		return false;
+	return true;
+}
+
+/*
+ * We current support XFS v5 formats with known features and v4 superblocks with
+ * at least V2 directories.
  */
 bool
 xfs_sb_good_version(
 	struct xfs_sb	*sbp)
 {
-	/* all v5 filesystems are supported */
+	/*
+	 * All v5 filesystems are supported, but we must check that all the
+	 * required v4 feature flags are enabled correctly as the code checks
+	 * those flags and not for v5 support.
+	 */
 	if (xfs_sb_is_v5(sbp))
-		return true;
+		return xfs_sb_validate_v5_features(sbp);
 
 	/* versions prior to v4 are not supported */
-	if (XFS_SB_VERSION_NUM(sbp) < XFS_SB_VERSION_4)
+	if (XFS_SB_VERSION_NUM(sbp) != XFS_SB_VERSION_4)
+		return false;
+
+	/* We must not have any unknown v4 feature bits set */
+	if ((sbp->sb_versionnum & ~XFS_SB_VERSION_OKBITS) ||
+	    ((sbp->sb_versionnum & XFS_SB_VERSION_MOREBITSBIT) &&
+	     (sbp->sb_features2 & ~XFS_SB_VERSION2_OKBITS)))
 		return false;
 
 	/* V4 filesystems need v2 directories and unwritten extents */
@@ -51,12 +103,6 @@
 	if (!(sbp->sb_versionnum & XFS_SB_VERSION_EXTFLGBIT))
 		return false;
 
-	/* And must not have any unknown v4 feature bits set */
-	if ((sbp->sb_versionnum & ~XFS_SB_VERSION_OKBITS) ||
-	    ((sbp->sb_versionnum & XFS_SB_VERSION_MOREBITSBIT) &&
-	     (sbp->sb_features2 & ~XFS_SB_VERSION2_OKBITS)))
-		return false;
-
 	/* It's a supported v4 filesystem */
 	return true;
 }
@@ -70,6 +116,8 @@
 	/* optional V4 features */
 	if (sbp->sb_rblocks > 0)
 		features |= XFS_FEAT_REALTIME;
+	if (sbp->sb_versionnum & XFS_SB_VERSION_NLINKBIT)
+		features |= XFS_FEAT_NLINK;
 	if (sbp->sb_versionnum & XFS_SB_VERSION_ATTRBIT)
 		features |= XFS_FEAT_ATTR;
 	if (sbp->sb_versionnum & XFS_SB_VERSION_QUOTABIT)
@@ -208,14 +256,8 @@
 	 * the kernel cannot support since we checked for unsupported bits in
 	 * the read verifier, which means that memory is corrupt.
 	 */
-	if (xfs_sb_has_compat_feature(sbp, XFS_SB_FEAT_COMPAT_UNKNOWN)) {
-		xfs_warn(mp,
-"Corruption detected in superblock compatible features (0x%x)!",
-			(sbp->sb_features_compat & XFS_SB_FEAT_COMPAT_UNKNOWN));
-		return -EFSCORRUPTED;
-	}
-
-	if (xfs_sb_has_ro_compat_feature(sbp, XFS_SB_FEAT_RO_COMPAT_UNKNOWN)) {
+	if (!xfs_is_readonly(mp) &&
+	    xfs_sb_has_ro_compat_feature(sbp, XFS_SB_FEAT_RO_COMPAT_UNKNOWN)) {
 		xfs_alert(mp,
 "Corruption detected in superblock read-only compatible features (0x%x)!",
 			(sbp->sb_features_ro_compat &
@@ -262,12 +304,15 @@
 	bool			has_dalign;
 
 	if (!xfs_verify_magic(bp, dsb->sb_magicnum)) {
-		xfs_warn(mp, "bad magic number");
+		xfs_warn(mp,
+"Superblock has bad magic number 0x%x. Not an XFS filesystem?",
+			be32_to_cpu(dsb->sb_magicnum));
 		return -EWRONGFS;
 	}
 
 	if (!xfs_sb_good_version(sbp)) {
-		xfs_warn(mp, "bad version");
+		xfs_warn(mp,
+"Superblock has unknown features enabled or corrupted feature masks.");
 		return -EWRONGFS;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_symlink_remote.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_symlink_remote.c
@@ -89,8 +89,10 @@
 	struct xfs_mount	*mp = bp->b_mount;
 	struct xfs_dsymlink_hdr	*dsl = bp->b_addr;
 
+	/* no verification of non-crc buffers */
 	if (!xfs_has_crc(mp))
-		return __this_address;
+		return NULL;
+
 	if (!xfs_verify_magic(bp, dsl->sl_magic))
 		return __this_address;
 	if (!uuid_equal(&dsl->sl_uuid, &mp->m_sb.sb_meta_uuid))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/libxfs/xfs_trans_resv.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/libxfs/xfs_trans_resv.c
@@ -423,7 +423,7 @@
 {
 	return XFS_DQUOT_LOGRES(mp) +
 		xfs_calc_iunlink_add_reservation(mp) +
-		max((xfs_calc_inode_res(mp, 1) +
+		max((xfs_calc_inode_res(mp, 2) +
 		     xfs_calc_buf_res(XFS_DIROP_LOG_COUNT(mp),
 				      XFS_FSB_TO_B(mp, 1))),
 		    (xfs_calc_buf_res(4, mp->m_sb.sb_sectsize) +
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/scrub/common.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/scrub/common.c
@@ -864,28 +864,3 @@
 	return -EDEADLOCK;
 }
 
-/* Pause background reaping of resources. */
-void
-xchk_stop_reaping(
-	struct xfs_scrub	*sc)
-{
-	sc->flags |= XCHK_REAPING_DISABLED;
-	xfs_blockgc_stop(sc->mp);
-	xfs_inodegc_stop(sc->mp);
-}
-
-/* Restart background reaping of resources. */
-void
-xchk_start_reaping(
-	struct xfs_scrub	*sc)
-{
-	/*
-	 * Readonly filesystems do not perform inactivation or speculative
-	 * preallocation, so there's no need to restart the workers.
-	 */
-	if (!xfs_is_readonly(sc->mp)) {
-		xfs_inodegc_start(sc->mp);
-		xfs_blockgc_start(sc->mp);
-	}
-	sc->flags &= ~XCHK_REAPING_DISABLED;
-}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/scrub/common.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/scrub/common.h
@@ -148,7 +148,5 @@
 
 int xchk_metadata_inode_forks(struct xfs_scrub *sc);
 int xchk_ilock_inverted(struct xfs_inode *ip, uint lock_mode);
-void xchk_stop_reaping(struct xfs_scrub *sc);
-void xchk_start_reaping(struct xfs_scrub *sc);
 
 #endif	/* __XFS_SCRUB_COMMON_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/scrub/fscounters.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/scrub/fscounters.c
@@ -128,13 +128,6 @@
 	if (error)
 		return error;
 
-	/*
-	 * Pause background reclaim while we're scrubbing to reduce the
-	 * likelihood of background perturbations to the counters throwing off
-	 * our calculations.
-	 */
-	xchk_stop_reaping(sc);
-
 	return xchk_trans_alloc(sc, 0);
 }
 
@@ -354,6 +347,12 @@
 		xchk_set_corrupt(sc);
 
 	/*
+	 * XXX: We can't quiesce percpu counter updates, so exit early.
+	 * This can be re-enabled when we gain exclusive freeze functionality.
+	 */
+	return 0;
+
+	/*
 	 * If ifree exceeds icount by more than the minimum variance then
 	 * something's probably wrong with the counters.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/scrub/scrub.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/scrub/scrub.c
@@ -171,8 +171,6 @@
 	}
 	if (sc->sm->sm_flags & XFS_SCRUB_IFLAG_REPAIR)
 		mnt_drop_write_file(sc->file);
-	if (sc->flags & XCHK_REAPING_DISABLED)
-		xchk_start_reaping(sc);
 	if (sc->flags & XCHK_HAS_QUOTAOFFLOCK) {
 		mutex_unlock(&sc->mp->m_quotainfo->qi_quotaofflock);
 		sc->flags &= ~XCHK_HAS_QUOTAOFFLOCK;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/scrub/scrub.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/scrub/scrub.h
@@ -89,7 +89,6 @@
 /* XCHK state flags grow up from zero, XREP state flags grown down from 2^31 */
 #define XCHK_TRY_HARDER		(1 << 0)  /* can't get resources, try again */
 #define XCHK_HAS_QUOTAOFFLOCK	(1 << 1)  /* we hold the quotaoff lock */
-#define XCHK_REAPING_DISABLED	(1 << 2)  /* background block reaping paused */
 #define XREP_ALREADY_FIXED	(1 << 31) /* checking our repair work */
 
 /* Metadata scrubbers */
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/scrub/trace.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/scrub/trace.h
@@ -464,7 +464,7 @@
 	TP_fast_assign(
 		xfs_fsblock_t fsbno = xchk_btree_cur_fsbno(cur, level);
 		__entry->dev = sc->mp->m_super->s_dev;
-		__entry->ino = sc->ip->i_ino;
+		__entry->ino = cur->bc_ino.ip->i_ino;
 		__entry->whichfork = cur->bc_ino.whichfork;
 		__entry->type = sc->sm->sm_type;
 		__entry->btnum = cur->bc_btnum;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_aops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_aops.c
@@ -82,6 +82,7 @@
 	struct iomap_ioend	*ioend)
 {
 	struct xfs_inode	*ip = XFS_I(ioend->io_inode);
+	struct xfs_mount	*mp = ip->i_mount;
 	xfs_off_t		offset = ioend->io_offset;
 	size_t			size = ioend->io_size;
 	unsigned int		nofs_flag;
@@ -97,18 +98,26 @@
 	/*
 	 * Just clean up the in-memory structures if the fs has been shut down.
 	 */
-	if (xfs_is_shutdown(ip->i_mount)) {
+	if (xfs_is_shutdown(mp)) {
 		error = -EIO;
 		goto done;
 	}
 
 	/*
-	 * Clean up any COW blocks on an I/O error.
+	 * Clean up all COW blocks and underlying data fork delalloc blocks on
+	 * I/O error. The delalloc punch is required because this ioend was
+	 * mapped to blocks in the COW fork and the associated pages are no
+	 * longer dirty. If we don't remove delalloc blocks here, they become
+	 * stale and can corrupt free space accounting on unmount.
 	 */
 	error = blk_status_to_errno(ioend->io_bio->bi_status);
 	if (unlikely(error)) {
-		if (ioend->io_flags & IOMAP_F_SHARED)
+		if (ioend->io_flags & IOMAP_F_SHARED) {
 			xfs_reflink_cancel_cow_range(ip, offset, size, true);
+			xfs_bmap_punch_delalloc_range(ip,
+						      XFS_B_TO_FSBT(mp, offset),
+						      XFS_B_TO_FSB(mp, size));
+		}
 		goto done;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_attr_inactive.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_attr_inactive.c
@@ -158,6 +158,7 @@
 	}
 	child_fsb = be32_to_cpu(ichdr.btree[0].before);
 	xfs_trans_brelse(*trans, bp);	/* no locks for later trans */
+	bp = NULL;
 
 	/*
 	 * If this is the node level just above the leaves, simply loop
@@ -211,12 +212,8 @@
 				&child_bp);
 		if (error)
 			return error;
-		error = bp->b_error;
-		if (error) {
-			xfs_trans_brelse(*trans, child_bp);
-			return error;
-		}
 		xfs_trans_binval(*trans, child_bp);
+		child_bp = NULL;
 
 		/*
 		 * If we're not done, re-read the parent to get the next
@@ -233,6 +230,7 @@
 						  bp->b_addr);
 			child_fsb = be32_to_cpu(phdr.btree[i + 1].before);
 			xfs_trans_brelse(*trans, bp);
+			bp = NULL;
 		}
 		/*
 		 * Atomically commit the whole invalidate stuff.
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_bio_io.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_bio_io.c
@@ -9,41 +9,6 @@
 	return bio_max_segs(howmany(count, PAGE_SIZE));
 }
 
-static void
-xfs_flush_bdev_async_endio(
-	struct bio	*bio)
-{
-	complete(bio->bi_private);
-}
-
-/*
- * Submit a request for an async cache flush to run. If the request queue does
- * not require flush operations, just skip it altogether. If the caller needs
- * to wait for the flush completion at a later point in time, they must supply a
- * valid completion. This will be signalled when the flush completes.  The
- * caller never sees the bio that is issued here.
- */
-void
-xfs_flush_bdev_async(
-	struct bio		*bio,
-	struct block_device	*bdev,
-	struct completion	*done)
-{
-	struct request_queue	*q = bdev->bd_disk->queue;
-
-	if (!test_bit(QUEUE_FLAG_WC, &q->queue_flags)) {
-		complete(done);
-		return;
-	}
-
-	bio_init(bio, NULL, 0);
-	bio_set_dev(bio, bdev);
-	bio->bi_opf = REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC;
-	bio->bi_private = done;
-	bio->bi_end_io = xfs_flush_bdev_async_endio;
-
-	submit_bio(bio);
-}
 int
 xfs_rw_bdev(
 	struct block_device	*bdev,
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_bmap_item.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_bmap_item.c
@@ -39,6 +39,7 @@
 xfs_bui_item_free(
 	struct xfs_bui_log_item	*buip)
 {
+	kmem_free(buip->bui_item.li_lv_shadow);
 	kmem_cache_free(xfs_bui_zone, buip);
 }
 
@@ -198,6 +199,7 @@
 	struct xfs_bud_log_item	*budp = BUD_ITEM(lip);
 
 	xfs_bui_release(budp->bud_buip);
+	kmem_free(budp->bud_item.li_lv_shadow);
 	kmem_cache_free(xfs_bud_zone, budp);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_bmap_util.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_bmap_util.c
@@ -851,9 +851,6 @@
 			rblocks = 0;
 		}
 
-		/*
-		 * Allocate and setup the transaction.
-		 */
 		error = xfs_trans_alloc_inode(ip, &M_RES(mp)->tr_write,
 				dblocks, rblocks, false, &tp);
 		if (error)
@@ -870,9 +867,9 @@
 		if (error)
 			goto error;
 
-		/*
-		 * Complete the transaction
-		 */
+		ip->i_diflags |= XFS_DIFLAG_PREALLOC;
+		xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
+
 		error = xfs_trans_commit(tp);
 		xfs_iunlock(ip, XFS_ILOCK_EXCL);
 		if (error)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_buf_item_recover.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_buf_item_recover.c
@@ -24,6 +24,15 @@
 #include "xfs_quota.h"
 
 /*
+ * This is the number of entries in the l_buf_cancel_table used during
+ * recovery.
+ */
+#define	XLOG_BC_TABLE_SIZE	64
+
+#define XLOG_BUF_CANCEL_BUCKET(log, blkno) \
+	((log)->l_buf_cancel_table + ((uint64_t)blkno % XLOG_BC_TABLE_SIZE))
+
+/*
  * This structure is used during recovery to record the buf log items which
  * have been canceled and should not be replayed.
  */
@@ -816,7 +825,7 @@
 	}
 
 	if (lsn != (xfs_lsn_t)-1) {
-		if (!uuid_equal(&mp->m_sb.sb_uuid, uuid))
+		if (!uuid_equal(&mp->m_sb.sb_meta_uuid, uuid))
 			goto recover_immediately;
 		return lsn;
 	}
@@ -934,6 +943,16 @@
 	if (lsn && lsn != -1 && XFS_LSN_CMP(lsn, current_lsn) >= 0) {
 		trace_xfs_log_recover_buf_skip(log, buf_f);
 		xlog_recover_validate_buf_type(mp, bp, buf_f, NULLCOMMITLSN);
+
+		/*
+		 * We're skipping replay of this buffer log item due to the log
+		 * item LSN being behind the ondisk buffer.  Verify the buffer
+		 * contents since we aren't going to run the write verifier.
+		 */
+		if (bp->b_ops) {
+			bp->b_ops->verify_read(bp);
+			error = bp->b_error;
+		}
 		goto out_release;
 	}
 
@@ -993,3 +1012,60 @@
 	.commit_pass1		= xlog_recover_buf_commit_pass1,
 	.commit_pass2		= xlog_recover_buf_commit_pass2,
 };
+
+#ifdef DEBUG
+void
+xlog_check_buf_cancel_table(
+	struct xlog	*log)
+{
+	int		i;
+
+	for (i = 0; i < XLOG_BC_TABLE_SIZE; i++)
+		ASSERT(list_empty(&log->l_buf_cancel_table[i]));
+}
+#endif
+
+int
+xlog_alloc_buf_cancel_table(
+	struct xlog	*log)
+{
+	void		*p;
+	int		i;
+
+	ASSERT(log->l_buf_cancel_table == NULL);
+
+	p = kmalloc_array(XLOG_BC_TABLE_SIZE, sizeof(struct list_head),
+			  GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
+	log->l_buf_cancel_table = p;
+	for (i = 0; i < XLOG_BC_TABLE_SIZE; i++)
+		INIT_LIST_HEAD(&log->l_buf_cancel_table[i]);
+
+	return 0;
+}
+
+void
+xlog_free_buf_cancel_table(
+	struct xlog	*log)
+{
+	int		i;
+
+	if (!log->l_buf_cancel_table)
+		return;
+
+	for (i = 0; i < XLOG_BC_TABLE_SIZE; i++) {
+		struct xfs_buf_cancel	*bc;
+
+		while ((bc = list_first_entry_or_null(
+				&log->l_buf_cancel_table[i],
+				struct xfs_buf_cancel, bc_list))) {
+			list_del(&bc->bc_list);
+			kmem_free(bc);
+		}
+	}
+
+	kmem_free(log->l_buf_cancel_table);
+	log->l_buf_cancel_table = NULL;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_error.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_error.c
@@ -224,13 +224,18 @@
 xfs_errortag_init(
 	struct xfs_mount	*mp)
 {
+	int ret;
+
 	mp->m_errortag = kmem_zalloc(sizeof(unsigned int) * XFS_ERRTAG_MAX,
 			KM_MAYFAIL);
 	if (!mp->m_errortag)
 		return -ENOMEM;
 
-	return xfs_sysfs_init(&mp->m_errortag_kobj, &xfs_errortag_ktype,
-			       &mp->m_kobj, "errortag");
+	ret = xfs_sysfs_init(&mp->m_errortag_kobj, &xfs_errortag_ktype,
+				&mp->m_kobj, "errortag");
+	if (ret)
+		kmem_free(mp->m_errortag);
+	return ret;
 }
 
 void
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_extfree_item.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_extfree_item.c
@@ -482,7 +482,7 @@
 			free->xefi_startblock,
 			free->xefi_blockcount,
 			&free->xefi_oinfo, free->xefi_skip_discard);
-	kmem_free(free);
+	kmem_cache_free(xfs_bmap_free_item_zone, free);
 	return error;
 }
 
@@ -502,7 +502,7 @@
 	struct xfs_extent_free_item	*free;
 
 	free = container_of(item, struct xfs_extent_free_item, xefi_list);
-	kmem_free(free);
+	kmem_cache_free(xfs_bmap_free_item_zone, free);
 }
 
 const struct xfs_defer_op_type xfs_extent_free_defer_type = {
@@ -564,7 +564,7 @@
 	extp->ext_len = free->xefi_blockcount;
 	efdp->efd_next_extent++;
 
-	kmem_free(free);
+	kmem_cache_free(xfs_bmap_free_item_zone, free);
 	return error;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_file.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_file.c
@@ -95,8 +95,6 @@
 		ip->i_diflags &= ~XFS_DIFLAG_PREALLOC;
 
 	xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
-	if (flags & XFS_PREALLOC_SYNC)
-		xfs_trans_set_sync(tp);
 	return xfs_trans_commit(tp);
 }
 
@@ -259,7 +257,7 @@
 	ret = xfs_ilock_iocb(iocb, XFS_IOLOCK_SHARED);
 	if (ret)
 		return ret;
-	ret = iomap_dio_rw(iocb, to, &xfs_read_iomap_ops, NULL, 0);
+	ret = iomap_dio_rw(iocb, to, &xfs_read_iomap_ops, NULL, 0, 0);
 	xfs_iunlock(ip, XFS_IOLOCK_SHARED);
 
 	return ret;
@@ -569,7 +567,7 @@
 	}
 	trace_xfs_file_direct_write(iocb, from);
 	ret = iomap_dio_rw(iocb, from, &xfs_direct_write_iomap_ops,
-			   &xfs_dio_write_ops, 0);
+			   &xfs_dio_write_ops, 0, 0);
 out_unlock:
 	if (iolock)
 		xfs_iunlock(ip, iolock);
@@ -647,7 +645,7 @@
 
 	trace_xfs_file_direct_write(iocb, from);
 	ret = iomap_dio_rw(iocb, from, &xfs_direct_write_iomap_ops,
-			   &xfs_dio_write_ops, flags);
+			   &xfs_dio_write_ops, flags, 0);
 
 	/*
 	 * Retry unaligned I/O with exclusive blocking semantics if the DIO
@@ -911,7 +909,6 @@
 	struct inode		*inode = file_inode(file);
 	struct xfs_inode	*ip = XFS_I(inode);
 	long			error;
-	enum xfs_prealloc_flags	flags = 0;
 	uint			iolock = XFS_IOLOCK_EXCL | XFS_MMAPLOCK_EXCL;
 	loff_t			new_size = 0;
 	bool			do_file_insert = false;
@@ -956,6 +953,10 @@
 			goto out_unlock;
 	}
 
+	error = file_modified(file);
+	if (error)
+		goto out_unlock;
+
 	if (mode & FALLOC_FL_PUNCH_HOLE) {
 		error = xfs_free_file_space(ip, offset, len);
 		if (error)
@@ -1005,8 +1006,6 @@
 		}
 		do_file_insert = true;
 	} else {
-		flags |= XFS_PREALLOC_SET;
-
 		if (!(mode & FALLOC_FL_KEEP_SIZE) &&
 		    offset + len > i_size_read(inode)) {
 			new_size = offset + len;
@@ -1059,13 +1058,6 @@
 		}
 	}
 
-	if (file->f_flags & O_DSYNC)
-		flags |= XFS_PREALLOC_SYNC;
-
-	error = xfs_update_prealloc_flags(ip, flags);
-	if (error)
-		goto out_unlock;
-
 	/* Change file size if needed */
 	if (new_size) {
 		struct iattr iattr;
@@ -1084,8 +1076,14 @@
 	 * leave shifted extents past EOF and hence losing access to
 	 * the data that is contained within them.
 	 */
-	if (do_file_insert)
+	if (do_file_insert) {
 		error = xfs_insert_file_space(ip, offset, len);
+		if (error)
+			goto out_unlock;
+	}
+
+	if (file->f_flags & O_DSYNC)
+		error = xfs_log_force_inode(ip);
 
 out_unlock:
 	xfs_iunlock(ip, iolock);
@@ -1195,6 +1193,14 @@
 	xfs_iunlock2_io_mmap(src, dest);
 	if (ret)
 		trace_xfs_reflink_remap_range_error(dest, ret, _RET_IP_);
+	/*
+	 * If the caller did not set CAN_SHORTEN, then it is not prepared to
+	 * handle partial results -- either the whole remap succeeds, or we
+	 * must say why it did not.  In this case, any error should be returned
+	 * to the caller.
+	 */
+	if (ret && remapped < len && !(remap_flags & REMAP_FILE_CAN_SHORTEN))
+		return ret;
 	return remapped > 0 ? remapped : ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_filestream.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_filestream.c
@@ -128,11 +128,12 @@
 		if (!pag->pagf_init) {
 			err = xfs_alloc_pagf_init(mp, NULL, ag, trylock);
 			if (err) {
-				xfs_perag_put(pag);
-				if (err != -EAGAIN)
+				if (err != -EAGAIN) {
+					xfs_perag_put(pag);
 					return err;
+				}
 				/* Couldn't lock the AGF, skip this AG. */
-				continue;
+				goto next_ag;
 			}
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_fsops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_fsops.c
@@ -430,46 +430,36 @@
 	 * If the request is larger than the current reservation, reserve the
 	 * blocks before we update the reserve counters. Sample m_fdblocks and
 	 * perform a partial reservation if the request exceeds free space.
+	 *
+	 * The code below estimates how many blocks it can request from
+	 * fdblocks to stash in the reserve pool.  This is a classic TOCTOU
+	 * race since fdblocks updates are not always coordinated via
+	 * m_sb_lock.  Set the reserve size even if there's not enough free
+	 * space to fill it because mod_fdblocks will refill an undersized
+	 * reserve when it can.
 	 */
-	error = -ENOSPC;
-	do {
-		free = percpu_counter_sum(&mp->m_fdblocks) -
-						mp->m_alloc_set_aside;
-		if (free <= 0)
-			break;
-
-		delta = request - mp->m_resblks;
-		lcounter = free - delta;
-		if (lcounter < 0)
-			/* We can't satisfy the request, just get what we can */
-			fdblks_delta = free;
-		else
-			fdblks_delta = delta;
-
+	free = percpu_counter_sum(&mp->m_fdblocks) -
+						xfs_fdblocks_unavailable(mp);
+	delta = request - mp->m_resblks;
+	mp->m_resblks = request;
+	if (delta > 0 && free > 0) {
 		/*
 		 * We'll either succeed in getting space from the free block
-		 * count or we'll get an ENOSPC. If we get a ENOSPC, it means
-		 * things changed while we were calculating fdblks_delta and so
-		 * we should try again to see if there is anything left to
-		 * reserve.
+		 * count or we'll get an ENOSPC.  Don't set the reserved flag
+		 * here - we don't want to reserve the extra reserve blocks
+		 * from the reserve.
 		 *
-		 * Don't set the reserved flag here - we don't want to reserve
-		 * the extra reserve blocks from the reserve.....
+		 * The desired reserve size can change after we drop the lock.
+		 * Use mod_fdblocks to put the space into the reserve or into
+		 * fdblocks as appropriate.
 		 */
+		fdblks_delta = min(free, delta);
 		spin_unlock(&mp->m_sb_lock);
 		error = xfs_mod_fdblocks(mp, -fdblks_delta, 0);
+		if (!error)
+			xfs_mod_fdblocks(mp, fdblks_delta, 0);
 		spin_lock(&mp->m_sb_lock);
-	} while (error == -ENOSPC);
-
-	/*
-	 * Update the reserve counters if blocks have been successfully
-	 * allocated.
-	 */
-	if (!error && fdblks_delta) {
-		mp->m_resblks += fdblks_delta;
-		mp->m_resblks_avail += fdblks_delta;
 	}
-
 out:
 	if (outval) {
 		outval->resblks = mp->m_resblks;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_icache.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_icache.c
@@ -448,18 +448,23 @@
 }
 
 /* Make all pending inactivation work start immediately. */
-static void
+static bool
 xfs_inodegc_queue_all(
 	struct xfs_mount	*mp)
 {
 	struct xfs_inodegc	*gc;
 	int			cpu;
+	bool			ret = false;
 
 	for_each_online_cpu(cpu) {
 		gc = per_cpu_ptr(mp->m_inodegc, cpu);
-		if (!llist_empty(&gc->list))
-			queue_work_on(cpu, mp->m_inodegc_wq, &gc->work);
+		if (!llist_empty(&gc->list)) {
+			mod_delayed_work_on(cpu, mp->m_inodegc_wq, &gc->work, 0);
+			ret = true;
+		}
 	}
+
+	return ret;
 }
 
 /*
@@ -1851,11 +1856,13 @@
 xfs_inodegc_worker(
 	struct work_struct	*work)
 {
-	struct xfs_inodegc	*gc = container_of(work, struct xfs_inodegc,
-							work);
+	struct xfs_inodegc	*gc = container_of(to_delayed_work(work),
+						struct xfs_inodegc, work);
 	struct llist_node	*node = llist_del_all(&gc->list);
 	struct xfs_inode	*ip, *n;
 
+	ASSERT(gc->cpu == smp_processor_id());
+
 	WRITE_ONCE(gc->items, 0);
 
 	if (!node)
@@ -1872,56 +1879,69 @@
 }
 
 /*
- * Force all currently queued inode inactivation work to run immediately, and
- * wait for the work to finish. Two pass - queue all the work first pass, wait
- * for it in a second pass.
+ * Expedite all pending inodegc work to run immediately. This does not wait for
+ * completion of the work.
  */
 void
-xfs_inodegc_flush(
+xfs_inodegc_push(
 	struct xfs_mount	*mp)
 {
-	struct xfs_inodegc	*gc;
-	int			cpu;
-
 	if (!xfs_is_inodegc_enabled(mp))
 		return;
-
-	trace_xfs_inodegc_flush(mp, __return_address);
-
+	trace_xfs_inodegc_push(mp, __return_address);
 	xfs_inodegc_queue_all(mp);
+}
 
-	for_each_online_cpu(cpu) {
-		gc = per_cpu_ptr(mp->m_inodegc, cpu);
-		flush_work(&gc->work);
-	}
+/*
+ * Force all currently queued inode inactivation work to run immediately and
+ * wait for the work to finish.
+ */
+void
+xfs_inodegc_flush(
+	struct xfs_mount	*mp)
+{
+	xfs_inodegc_push(mp);
+	trace_xfs_inodegc_flush(mp, __return_address);
+	flush_workqueue(mp->m_inodegc_wq);
 }
 
 /*
  * Flush all the pending work and then disable the inode inactivation background
- * workers and wait for them to stop.
+ * workers and wait for them to stop.  Caller must hold sb->s_umount to
+ * coordinate changes in the inodegc_enabled state.
  */
 void
 xfs_inodegc_stop(
 	struct xfs_mount	*mp)
 {
-	struct xfs_inodegc	*gc;
-	int			cpu;
+	bool			rerun;
 
 	if (!xfs_clear_inodegc_enabled(mp))
 		return;
 
+	/*
+	 * Drain all pending inodegc work, including inodes that could be
+	 * queued by racing xfs_inodegc_queue or xfs_inodegc_shrinker_scan
+	 * threads that sample the inodegc state just prior to us clearing it.
+	 * The inodegc flag state prevents new threads from queuing more
+	 * inodes, so we queue pending work items and flush the workqueue until
+	 * all inodegc lists are empty.  IOWs, we cannot use drain_workqueue
+	 * here because it does not allow other unserialized mechanisms to
+	 * reschedule inodegc work while this draining is in progress.
+	 */
 	xfs_inodegc_queue_all(mp);
+	do {
+		flush_workqueue(mp->m_inodegc_wq);
+		rerun = xfs_inodegc_queue_all(mp);
+	} while (rerun);
 
-	for_each_online_cpu(cpu) {
-		gc = per_cpu_ptr(mp->m_inodegc, cpu);
-		cancel_work_sync(&gc->work);
-	}
 	trace_xfs_inodegc_stop(mp, __return_address);
 }
 
 /*
  * Enable the inode inactivation background workers and schedule deferred inode
- * inactivation work if there is any.
+ * inactivation work if there is any.  Caller must hold sb->s_umount to
+ * coordinate changes in the inodegc_enabled state.
  */
 void
 xfs_inodegc_start(
@@ -2035,6 +2055,7 @@
 	struct xfs_inodegc	*gc;
 	int			items;
 	unsigned int		shrinker_hits;
+	unsigned long		queue_delay = 1;
 
 	trace_xfs_inode_set_need_inactive(ip);
 	spin_lock(&ip->i_flags_lock);
@@ -2046,19 +2067,27 @@
 	items = READ_ONCE(gc->items);
 	WRITE_ONCE(gc->items, items + 1);
 	shrinker_hits = READ_ONCE(gc->shrinker_hits);
-	put_cpu_ptr(gc);
 
-	if (!xfs_is_inodegc_enabled(mp))
+	/*
+	 * We queue the work while holding the current CPU so that the work
+	 * is scheduled to run on this CPU.
+	 */
+	if (!xfs_is_inodegc_enabled(mp)) {
+		put_cpu_ptr(gc);
 		return;
-
-	if (xfs_inodegc_want_queue_work(ip, items)) {
-		trace_xfs_inodegc_queue(mp, __return_address);
-		queue_work(mp->m_inodegc_wq, &gc->work);
 	}
 
+	if (xfs_inodegc_want_queue_work(ip, items))
+		queue_delay = 0;
+
+	trace_xfs_inodegc_queue(mp, __return_address);
+	mod_delayed_work_on(current_cpu(), mp->m_inodegc_wq, &gc->work,
+			queue_delay);
+	put_cpu_ptr(gc);
+
 	if (xfs_inodegc_want_flush_work(ip, items, shrinker_hits)) {
 		trace_xfs_inodegc_throttle(mp, __return_address);
-		flush_work(&gc->work);
+		flush_delayed_work(&gc->work);
 	}
 }
 
@@ -2075,7 +2104,7 @@
 	unsigned int		count = 0;
 
 	dead_gc = per_cpu_ptr(mp->m_inodegc, dead_cpu);
-	cancel_work_sync(&dead_gc->work);
+	cancel_delayed_work_sync(&dead_gc->work);
 
 	if (llist_empty(&dead_gc->list))
 		return;
@@ -2094,12 +2123,13 @@
 	llist_add_batch(first, last, &gc->list);
 	count += READ_ONCE(gc->items);
 	WRITE_ONCE(gc->items, count);
-	put_cpu_ptr(gc);
 
 	if (xfs_is_inodegc_enabled(mp)) {
 		trace_xfs_inodegc_queue(mp, __return_address);
-		queue_work(mp->m_inodegc_wq, &gc->work);
+		mod_delayed_work_on(current_cpu(), mp->m_inodegc_wq, &gc->work,
+				0);
 	}
+	put_cpu_ptr(gc);
 }
 
 /*
@@ -2194,7 +2224,7 @@
 			unsigned int	h = READ_ONCE(gc->shrinker_hits);
 
 			WRITE_ONCE(gc->shrinker_hits, h + 1);
-			queue_work_on(cpu, mp->m_inodegc_wq, &gc->work);
+			mod_delayed_work_on(cpu, mp->m_inodegc_wq, &gc->work, 0);
 			no_items = false;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_icache.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_icache.h
@@ -76,6 +76,7 @@
 void xfs_blockgc_start(struct xfs_mount *mp);
 
 void xfs_inodegc_worker(struct work_struct *work);
+void xfs_inodegc_push(struct xfs_mount *mp);
 void xfs_inodegc_flush(struct xfs_mount *mp);
 void xfs_inodegc_stop(struct xfs_mount *mp);
 void xfs_inodegc_start(struct xfs_mount *mp);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_icreate_item.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_icreate_item.c
@@ -63,6 +63,7 @@
 xfs_icreate_item_release(
 	struct xfs_log_item	*lip)
 {
+	kmem_free(ICR_ITEM(lip)->ic_item.li_lv_shadow);
 	kmem_cache_free(xfs_icreate_zone, ICR_ITEM(lip));
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_inode.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_inode.c
@@ -378,8 +378,8 @@
 	}
 
 	if (lock_flags & (XFS_MMAPLOCK_EXCL|XFS_MMAPLOCK_SHARED)) {
-		return __xfs_rwsem_islocked(&VFS_I(ip)->i_rwsem,
-				(lock_flags & XFS_IOLOCK_SHARED));
+		return __xfs_rwsem_islocked(&VFS_I(ip)->i_mapping->invalidate_lock,
+				(lock_flags & XFS_MMAPLOCK_SHARED));
 	}
 
 	if (lock_flags & (XFS_IOLOCK_EXCL | XFS_IOLOCK_SHARED)) {
@@ -994,8 +994,8 @@
 	/*
 	 * Make sure that we have allocated dquot(s) on disk.
 	 */
-	error = xfs_qm_vop_dqalloc(dp, mapped_fsuid(mnt_userns),
-			mapped_fsgid(mnt_userns), prid,
+	error = xfs_qm_vop_dqalloc(dp, mapped_fsuid(mnt_userns, &init_user_ns),
+			mapped_fsgid(mnt_userns, &init_user_ns), prid,
 			XFS_QMOPT_QUOTALL | XFS_QMOPT_INHERIT,
 			&udqp, &gdqp, &pdqp);
 	if (error)
@@ -1148,8 +1148,8 @@
 	/*
 	 * Make sure that we have allocated dquot(s) on disk.
 	 */
-	error = xfs_qm_vop_dqalloc(dp, mapped_fsuid(mnt_userns),
-			mapped_fsgid(mnt_userns), prid,
+	error = xfs_qm_vop_dqalloc(dp, mapped_fsuid(mnt_userns, &init_user_ns),
+			mapped_fsgid(mnt_userns, &init_user_ns), prid,
 			XFS_QMOPT_QUOTALL | XFS_QMOPT_INHERIT,
 			&udqp, &gdqp, &pdqp);
 	if (error)
@@ -1223,7 +1223,7 @@
 {
 	xfs_mount_t		*mp = tdp->i_mount;
 	xfs_trans_t		*tp;
-	int			error;
+	int			error, nospace_error = 0;
 	int			resblks;
 
 	trace_xfs_link(tdp, target_name);
@@ -1242,19 +1242,11 @@
 		goto std_return;
 
 	resblks = XFS_LINK_SPACE_RES(mp, target_name->len);
-	error = xfs_trans_alloc(mp, &M_RES(mp)->tr_link, resblks, 0, 0, &tp);
-	if (error == -ENOSPC) {
-		resblks = 0;
-		error = xfs_trans_alloc(mp, &M_RES(mp)->tr_link, 0, 0, 0, &tp);
-	}
+	error = xfs_trans_alloc_dir(tdp, &M_RES(mp)->tr_link, sip, &resblks,
+			&tp, &nospace_error);
 	if (error)
 		goto std_return;
 
-	xfs_lock_two_inodes(sip, XFS_ILOCK_EXCL, tdp, XFS_ILOCK_EXCL);
-
-	xfs_trans_ijoin(tp, sip, XFS_ILOCK_EXCL);
-	xfs_trans_ijoin(tp, tdp, XFS_ILOCK_EXCL);
-
 	error = xfs_iext_count_may_overflow(tdp, XFS_DATA_FORK,
 			XFS_IEXT_DIR_MANIP_CNT(mp));
 	if (error)
@@ -1312,6 +1304,8 @@
  error_return:
 	xfs_trans_cancel(tp);
  std_return:
+	if (error == -ENOSPC && nospace_error)
+		error = nospace_error;
 	return error;
 }
 
@@ -1754,8 +1748,11 @@
 		goto out;
 
 	/* Try to clean out the cow blocks if there are any. */
-	if (xfs_inode_has_cow_data(ip))
-		xfs_reflink_cancel_cow_range(ip, 0, NULLFILEOFF, true);
+	if (xfs_inode_has_cow_data(ip)) {
+		error = xfs_reflink_cancel_cow_range(ip, 0, NULLFILEOFF, true);
+		if (error)
+			goto out;
+	}
 
 	if (VFS_I(ip)->i_nlink != 0) {
 		/*
@@ -2605,14 +2602,13 @@
 }
 
 /*
- * This is called to return an inode to the inode free list.
- * The inode should already be truncated to 0 length and have
- * no pages associated with it.  This routine also assumes that
- * the inode is already a part of the transaction.
- *
- * The on-disk copy of the inode will have been added to the list
- * of unlinked inodes in the AGI. We need to remove the inode from
- * that list atomically with respect to freeing it here.
+ * This is called to return an inode to the inode free list.  The inode should
+ * already be truncated to 0 length and have no pages associated with it.  This
+ * routine also assumes that the inode is already a part of the transaction.
+ *
+ * The on-disk copy of the inode will have been added to the list of unlinked
+ * inodes in the AGI. We need to remove the inode from that list atomically with
+ * respect to freeing it here.
  */
 int
 xfs_ifree(
@@ -2634,13 +2630,16 @@
 	pag = xfs_perag_get(mp, XFS_INO_TO_AGNO(mp, ip->i_ino));
 
 	/*
-	 * Pull the on-disk inode from the AGI unlinked list.
+	 * Free the inode first so that we guarantee that the AGI lock is going
+	 * to be taken before we remove the inode from the unlinked list. This
+	 * makes the AGI lock -> unlinked list modification order the same as
+	 * used in O_TMPFILE creation.
 	 */
-	error = xfs_iunlink_remove(tp, pag, ip);
+	error = xfs_difree(tp, pag, ip->i_ino, &xic);
 	if (error)
 		goto out;
 
-	error = xfs_difree(tp, pag, ip->i_ino, &xic);
+	error = xfs_iunlink_remove(tp, pag, ip);
 	if (error)
 		goto out;
 
@@ -2761,6 +2760,7 @@
 	xfs_mount_t		*mp = dp->i_mount;
 	xfs_trans_t             *tp = NULL;
 	int			is_dir = S_ISDIR(VFS_I(ip)->i_mode);
+	int			dontcare;
 	int                     error = 0;
 	uint			resblks;
 
@@ -2778,31 +2778,24 @@
 		goto std_return;
 
 	/*
-	 * We try to get the real space reservation first,
-	 * allowing for directory btree deletion(s) implying
-	 * possible bmap insert(s).  If we can't get the space
-	 * reservation then we use 0 instead, and avoid the bmap
-	 * btree insert(s) in the directory code by, if the bmap
-	 * insert tries to happen, instead trimming the LAST
-	 * block from the directory.
+	 * We try to get the real space reservation first, allowing for
+	 * directory btree deletion(s) implying possible bmap insert(s).  If we
+	 * can't get the space reservation then we use 0 instead, and avoid the
+	 * bmap btree insert(s) in the directory code by, if the bmap insert
+	 * tries to happen, instead trimming the LAST block from the directory.
+	 *
+	 * Ignore EDQUOT and ENOSPC being returned via nospace_error because
+	 * the directory code can handle a reservationless update and we don't
+	 * want to prevent a user from trying to free space by deleting things.
 	 */
 	resblks = XFS_REMOVE_SPACE_RES(mp);
-	error = xfs_trans_alloc(mp, &M_RES(mp)->tr_remove, resblks, 0, 0, &tp);
-	if (error == -ENOSPC) {
-		resblks = 0;
-		error = xfs_trans_alloc(mp, &M_RES(mp)->tr_remove, 0, 0, 0,
-				&tp);
-	}
+	error = xfs_trans_alloc_dir(dp, &M_RES(mp)->tr_remove, ip, &resblks,
+			&tp, &dontcare);
 	if (error) {
 		ASSERT(error != -ENOSPC);
 		goto std_return;
 	}
 
-	xfs_lock_two_inodes(dp, XFS_ILOCK_EXCL, ip, XFS_ILOCK_EXCL);
-
-	xfs_trans_ijoin(tp, dp, XFS_ILOCK_EXCL);
-	xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL);
-
 	/*
 	 * If we're removing a directory perform some additional validation.
 	 */
@@ -3115,7 +3108,8 @@
 	bool			new_parent = (src_dp != target_dp);
 	bool			src_is_directory = S_ISDIR(VFS_I(src_ip)->i_mode);
 	int			spaceres;
-	int			error;
+	bool			retried = false;
+	int			error, nospace_error = 0;
 
 	trace_xfs_rename(src_dp, target_dp, src_name, target_name);
 
@@ -3128,7 +3122,6 @@
 	 * appropriately.
 	 */
 	if (flags & RENAME_WHITEOUT) {
-		ASSERT(!(flags & (RENAME_NOREPLACE | RENAME_EXCHANGE)));
 		error = xfs_rename_alloc_whiteout(mnt_userns, target_dp, &wip);
 		if (error)
 			return error;
@@ -3140,9 +3133,12 @@
 	xfs_sort_for_rename(src_dp, target_dp, src_ip, target_ip, wip,
 				inodes, &num_inodes);
 
+retry:
+	nospace_error = 0;
 	spaceres = XFS_RENAME_SPACE_RES(mp, target_name->len);
 	error = xfs_trans_alloc(mp, &M_RES(mp)->tr_rename, spaceres, 0, 0, &tp);
 	if (error == -ENOSPC) {
+		nospace_error = error;
 		spaceres = 0;
 		error = xfs_trans_alloc(mp, &M_RES(mp)->tr_rename, 0, 0, 0,
 				&tp);
@@ -3197,6 +3193,31 @@
 					spaceres);
 
 	/*
+	 * Try to reserve quota to handle an expansion of the target directory.
+	 * We'll allow the rename to continue in reservationless mode if we hit
+	 * a space usage constraint.  If we trigger reservationless mode, save
+	 * the errno if there isn't any free space in the target directory.
+	 */
+	if (spaceres != 0) {
+		error = xfs_trans_reserve_quota_nblks(tp, target_dp, spaceres,
+				0, false);
+		if (error == -EDQUOT || error == -ENOSPC) {
+			if (!retried) {
+				xfs_trans_cancel(tp);
+				xfs_blockgc_free_quota(target_dp, 0);
+				retried = true;
+				goto retry;
+			}
+
+			nospace_error = error;
+			spaceres = 0;
+			error = 0;
+		}
+		if (error)
+			goto out_trans_cancel;
+	}
+
+	/*
 	 * Check for expected errors before we dirty the transaction
 	 * so we can return an error without a transaction abort.
 	 *
@@ -3442,6 +3463,8 @@
 out_release_wip:
 	if (wip)
 		xfs_irele(wip);
+	if (error == -ENOSPC && nospace_error)
+		error = nospace_error;
 	return error;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_ioctl.c
@@ -372,7 +372,7 @@
 xfs_ioc_attr_list(
 	struct xfs_inode		*dp,
 	void __user			*ubuf,
-	int				bufsize,
+	size_t				bufsize,
 	int				flags,
 	struct xfs_attrlist_cursor __user *ucursor)
 {
@@ -687,7 +687,8 @@
 
 	if (bf->l_start > XFS_ISIZE(ip)) {
 		error = xfs_alloc_file_space(ip, XFS_ISIZE(ip),
-				bf->l_start - XFS_ISIZE(ip), 0);
+				bf->l_start - XFS_ISIZE(ip),
+				XFS_BMAPI_PREALLOC);
 		if (error)
 			goto out_unlock;
 	}
@@ -1544,7 +1545,7 @@
 
 	if (bmx.bmv_count < 2)
 		return -EINVAL;
-	if (bmx.bmv_count > ULONG_MAX / recsize)
+	if (bmx.bmv_count >= INT_MAX / recsize)
 		return -ENOMEM;
 
 	buf = kvzalloc(bmx.bmv_count * sizeof(*buf), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_ioctl.h
@@ -38,8 +38,9 @@
 int xfs_ioc_attrmulti_one(struct file *parfilp, struct inode *inode,
 		uint32_t opcode, void __user *uname, void __user *value,
 		uint32_t *len, uint32_t flags);
-int xfs_ioc_attr_list(struct xfs_inode *dp, void __user *ubuf, int bufsize,
-	int flags, struct xfs_attrlist_cursor __user *ucursor);
+int xfs_ioc_attr_list(struct xfs_inode *dp, void __user *ubuf,
+		      size_t bufsize, int flags,
+		      struct xfs_attrlist_cursor __user *ucursor);
 
 extern struct dentry *
 xfs_handle_to_dentry(
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_iops.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_iops.c
@@ -511,27 +511,6 @@
 	return ERR_PTR(error);
 }
 
-STATIC const char *
-xfs_vn_get_link_inline(
-	struct dentry		*dentry,
-	struct inode		*inode,
-	struct delayed_call	*done)
-{
-	struct xfs_inode	*ip = XFS_I(inode);
-	char			*link;
-
-	ASSERT(ip->i_df.if_format == XFS_DINODE_FMT_LOCAL);
-
-	/*
-	 * The VFS crashes on a NULL pointer, so return -EFSCORRUPTED if
-	 * if_data is junk.
-	 */
-	link = ip->i_df.if_u1.if_data;
-	if (XFS_IS_CORRUPT(ip->i_mount, !link))
-		return ERR_PTR(-EFSCORRUPTED);
-	return link;
-}
-
 static uint32_t
 xfs_stat_blksize(
 	struct xfs_inode	*ip)
@@ -634,37 +613,6 @@
 	return 0;
 }
 
-static void
-xfs_setattr_mode(
-	struct xfs_inode	*ip,
-	struct iattr		*iattr)
-{
-	struct inode		*inode = VFS_I(ip);
-	umode_t			mode = iattr->ia_mode;
-
-	ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL));
-
-	inode->i_mode &= S_IFMT;
-	inode->i_mode |= mode & ~S_IFMT;
-}
-
-void
-xfs_setattr_time(
-	struct xfs_inode	*ip,
-	struct iattr		*iattr)
-{
-	struct inode		*inode = VFS_I(ip);
-
-	ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL));
-
-	if (iattr->ia_valid & ATTR_ATIME)
-		inode->i_atime = iattr->ia_atime;
-	if (iattr->ia_valid & ATTR_CTIME)
-		inode->i_ctime = iattr->ia_ctime;
-	if (iattr->ia_valid & ATTR_MTIME)
-		inode->i_mtime = iattr->ia_mtime;
-}
-
 static int
 xfs_vn_change_ok(
 	struct user_namespace	*mnt_userns,
@@ -764,16 +712,6 @@
 		uid = (mask & ATTR_UID) ? iattr->ia_uid : iuid;
 
 		/*
-		 * CAP_FSETID overrides the following restrictions:
-		 *
-		 * The set-user-ID and set-group-ID bits of a file will be
-		 * cleared upon successful return from chown()
-		 */
-		if ((inode->i_mode & (S_ISUID|S_ISGID)) &&
-		    !capable(CAP_FSETID))
-			inode->i_mode &= ~(S_ISUID|S_ISGID);
-
-		/*
 		 * Change the ownerships and register quota modifications
 		 * in the transaction.
 		 */
@@ -784,7 +722,6 @@
 				olddquot1 = xfs_qm_vop_chown(tp, ip,
 							&ip->i_udquot, udqp);
 			}
-			inode->i_uid = uid;
 		}
 		if (!gid_eq(igid, gid)) {
 			if (XFS_IS_GQUOTA_ON(mp)) {
@@ -795,15 +732,10 @@
 				olddquot2 = xfs_qm_vop_chown(tp, ip,
 							&ip->i_gdquot, gdqp);
 			}
-			inode->i_gid = gid;
 		}
 	}
 
-	if (mask & ATTR_MODE)
-		xfs_setattr_mode(ip, iattr);
-	if (mask & (ATTR_ATIME|ATTR_CTIME|ATTR_MTIME))
-		xfs_setattr_time(ip, iattr);
-
+	setattr_copy(mnt_userns, inode, iattr);
 	xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
 
 	XFS_STATS_INC(mp, xs_ig_attrchg);
@@ -1028,11 +960,8 @@
 		xfs_inode_clear_eofblocks_tag(ip);
 	}
 
-	if (iattr->ia_valid & ATTR_MODE)
-		xfs_setattr_mode(ip, iattr);
-	if (iattr->ia_valid & (ATTR_ATIME|ATTR_CTIME|ATTR_MTIME))
-		xfs_setattr_time(ip, iattr);
-
+	ASSERT(!(iattr->ia_valid & (ATTR_UID | ATTR_GID)));
+	setattr_copy(mnt_userns, inode, iattr);
 	xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
 
 	XFS_STATS_INC(mp, xs_ig_attrchg);
@@ -1250,14 +1179,6 @@
 	.update_time		= xfs_vn_update_time,
 };
 
-static const struct inode_operations xfs_inline_symlink_inode_operations = {
-	.get_link		= xfs_vn_get_link_inline,
-	.getattr		= xfs_vn_getattr,
-	.setattr		= xfs_vn_setattr,
-	.listxattr		= xfs_vn_listxattr,
-	.update_time		= xfs_vn_update_time,
-};
-
 /* Figure out if this file actually supports DAX. */
 static bool
 xfs_inode_supports_dax(
@@ -1408,10 +1329,7 @@
 		inode->i_fop = &xfs_dir_file_operations;
 		break;
 	case S_IFLNK:
-		if (ip->i_df.if_format == XFS_DINODE_FMT_LOCAL)
-			inode->i_op = &xfs_inline_symlink_inode_operations;
-		else
-			inode->i_op = &xfs_symlink_inode_operations;
+		inode->i_op = &xfs_symlink_inode_operations;
 		break;
 	default:
 		inode->i_op = &xfs_inode_operations;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_iops.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_iops.h
@@ -13,7 +13,6 @@
 
 extern ssize_t xfs_vn_listxattr(struct dentry *, char *data, size_t size);
 
-extern void xfs_setattr_time(struct xfs_inode *ip, struct iattr *iattr);
 int xfs_vn_setattr_size(struct user_namespace *mnt_userns,
 		struct dentry *dentry, struct iattr *vap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_linux.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_linux.h
@@ -61,6 +61,7 @@
 #include <linux/ratelimit.h>
 #include <linux/rhashtable.h>
 #include <linux/xattr.h>
+#include <linux/mnt_idmapping.h>
 
 #include <asm/page.h>
 #include <asm/div64.h>
@@ -196,8 +197,6 @@
 
 int xfs_rw_bdev(struct block_device *bdev, sector_t sector, unsigned int count,
 		char *data, unsigned int op);
-void xfs_flush_bdev_async(struct bio *bio, struct block_device *bdev,
-		struct completion *done);
 
 #define ASSERT_ALWAYS(expr)	\
 	(likely(expr) ? (void)0 : assfail(NULL, #expr, __FILE__, __LINE__))
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_log.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_log.c
@@ -487,7 +487,10 @@
  * Run all the pending iclog callbacks and wake log force waiters and iclog
  * space waiters so they can process the newly set shutdown state. We really
  * don't care what order we process callbacks here because the log is shut down
- * and so state cannot change on disk anymore.
+ * and so state cannot change on disk anymore. However, we cannot wake waiters
+ * until the callbacks have been processed because we may be in unmount and
+ * we must ensure that all AIL operations the callbacks perform have completed
+ * before we tear down the AIL.
  *
  * We avoid processing actively referenced iclogs so that we don't run callbacks
  * while the iclog owner might still be preparing the iclog for IO submssion.
@@ -501,7 +504,6 @@
 	struct xlog_in_core	*iclog;
 	LIST_HEAD(cb_list);
 
-	spin_lock(&log->l_icloglock);
 	iclog = log->l_iclog;
 	do {
 		if (atomic_read(&iclog->ic_refcnt)) {
@@ -509,26 +511,22 @@
 			continue;
 		}
 		list_splice_init(&iclog->ic_callbacks, &cb_list);
+		spin_unlock(&log->l_icloglock);
+
+		xlog_cil_process_committed(&cb_list);
+
+		spin_lock(&log->l_icloglock);
 		wake_up_all(&iclog->ic_write_wait);
 		wake_up_all(&iclog->ic_force_wait);
 	} while ((iclog = iclog->ic_next) != log->l_iclog);
 
 	wake_up_all(&log->l_flush_wait);
-	spin_unlock(&log->l_icloglock);
-
-	xlog_cil_process_committed(&cb_list);
 }
 
 /*
  * Flush iclog to disk if this is the last reference to the given iclog and the
  * it is in the WANT_SYNC state.
  *
- * If the caller passes in a non-zero @old_tail_lsn and the current log tail
- * does not match, there may be metadata on disk that must be persisted before
- * this iclog is written.  To satisfy that requirement, set the
- * XLOG_ICL_NEED_FLUSH flag as a condition for writing this iclog with the new
- * log tail value.
- *
  * If XLOG_ICL_NEED_FUA is already set on the iclog, we need to ensure that the
  * log tail is updated correctly. NEED_FUA indicates that the iclog will be
  * written to stable storage, and implies that a commit record is contained
@@ -545,12 +543,10 @@
  * always capture the tail lsn on the iclog on the first NEED_FUA release
  * regardless of the number of active reference counts on this iclog.
  */
-
 int
 xlog_state_release_iclog(
 	struct xlog		*log,
-	struct xlog_in_core	*iclog,
-	xfs_lsn_t		old_tail_lsn)
+	struct xlog_in_core	*iclog)
 {
 	xfs_lsn_t		tail_lsn;
 	bool			last_ref;
@@ -561,18 +557,14 @@
 	/*
 	 * Grabbing the current log tail needs to be atomic w.r.t. the writing
 	 * of the tail LSN into the iclog so we guarantee that the log tail does
-	 * not move between deciding if a cache flush is required and writing
-	 * the LSN into the iclog below.
+	 * not move between the first time we know that the iclog needs to be
+	 * made stable and when we eventually submit it.
 	 */
-	if (old_tail_lsn || iclog->ic_state == XLOG_STATE_WANT_SYNC) {
+	if ((iclog->ic_state == XLOG_STATE_WANT_SYNC ||
+	     (iclog->ic_flags & XLOG_ICL_NEED_FUA)) &&
+	    !iclog->ic_header.h_tail_lsn) {
 		tail_lsn = xlog_assign_tail_lsn(log->l_mp);
-
-		if (old_tail_lsn && tail_lsn != old_tail_lsn)
-			iclog->ic_flags |= XLOG_ICL_NEED_FLUSH;
-
-		if ((iclog->ic_flags & XLOG_ICL_NEED_FUA) &&
-		    !iclog->ic_header.h_tail_lsn)
-			iclog->ic_header.h_tail_lsn = cpu_to_be64(tail_lsn);
+		iclog->ic_header.h_tail_lsn = cpu_to_be64(tail_lsn);
 	}
 
 	last_ref = atomic_dec_and_test(&iclog->ic_refcnt);
@@ -583,11 +575,8 @@
 		 * pending iclog callbacks that were waiting on the release of
 		 * this iclog.
 		 */
-		if (last_ref) {
-			spin_unlock(&log->l_icloglock);
+		if (last_ref)
 			xlog_state_shutdown_callbacks(log);
-			spin_lock(&log->l_icloglock);
-		}
 		return -EIO;
 	}
 
@@ -600,8 +589,6 @@
 	}
 
 	iclog->ic_state = XLOG_STATE_SYNCING;
-	if (!iclog->ic_header.h_tail_lsn)
-		iclog->ic_header.h_tail_lsn = cpu_to_be64(tail_lsn);
 	xlog_verify_tail_lsn(log, iclog);
 	trace_xlog_iclog_syncing(iclog, _RET_IP_);
 
@@ -720,15 +707,7 @@
 	 * just worked.
 	 */
 	if (!xfs_has_norecovery(mp)) {
-		/*
-		 * log recovery ignores readonly state and so we need to clear
-		 * mount-based read only state so it can write to disk.
-		 */
-		bool	readonly = test_and_clear_bit(XFS_OPSTATE_READONLY,
-						&mp->m_opstate);
 		error = xlog_recover(log);
-		if (readonly)
-			set_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
 		if (error) {
 			xfs_warn(mp, "log mount/recovery failed: error %d",
 				error);
@@ -777,7 +756,6 @@
 	struct xfs_mount	*mp)
 {
 	struct xlog		*log = mp->m_log;
-	bool			readonly;
 	int			error = 0;
 
 	if (xfs_has_norecovery(mp)) {
@@ -786,12 +764,6 @@
 	}
 
 	/*
-	 * log recovery ignores readonly state and so we need to clear
-	 * mount-based read only state so it can write to disk.
-	 */
-	readonly = test_and_clear_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
-
-	/*
 	 * During the second phase of log recovery, we need iget and
 	 * iput to behave like they do for an active filesystem.
 	 * xfs_fs_drop_inode needs to be able to prevent the deletion
@@ -841,8 +813,6 @@
 	xfs_buftarg_drain(mp->m_ddev_targp);
 
 	clear_bit(XLOG_RECOVERY_NEEDED, &log->l_opstate);
-	if (readonly)
-		set_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
 
 	/* Make sure the log is dead if we're returning failure. */
 	ASSERT(!error || xlog_is_shutdown(log));
@@ -874,7 +844,7 @@
 	iclog->ic_flags |= XLOG_ICL_NEED_FLUSH | XLOG_ICL_NEED_FUA;
 	if (iclog->ic_state == XLOG_STATE_ACTIVE)
 		xlog_state_switch_iclogs(iclog->ic_log, iclog, 0);
-	return xlog_state_release_iclog(iclog->ic_log, iclog, 0);
+	return xlog_state_release_iclog(iclog->ic_log, iclog);
 }
 
 /*
@@ -2074,8 +2044,6 @@
 	xlog_in_core_t	*iclog, *next_iclog;
 	int		i;
 
-	xlog_cil_destroy(log);
-
 	/*
 	 * Cycle all the iclogbuf locks to make sure all log IO completion
 	 * is done before we tear down these buffers.
@@ -2087,6 +2055,13 @@
 		iclog = iclog->ic_next;
 	}
 
+	/*
+	 * Destroy the CIL after waiting for iclog IO completion because an
+	 * iclog EIO error will try to shut down the log, which accesses the
+	 * CIL to wake up the waiters.
+	 */
+	xlog_cil_destroy(log);
+
 	iclog = log->l_iclog;
 	for (i = 0; i < log->l_iclog_bufs; i++) {
 		next_iclog = iclog->ic_next;
@@ -2412,7 +2387,7 @@
 		ASSERT(iclog->ic_state == XLOG_STATE_WANT_SYNC ||
 			xlog_is_shutdown(log));
 release_iclog:
-	error = xlog_state_release_iclog(log, iclog, 0);
+	error = xlog_state_release_iclog(log, iclog);
 	spin_unlock(&log->l_icloglock);
 	return error;
 }
@@ -2629,7 +2604,7 @@
 
 	spin_lock(&log->l_icloglock);
 	xlog_state_finish_copy(log, iclog, record_cnt, data_cnt);
-	error = xlog_state_release_iclog(log, iclog, 0);
+	error = xlog_state_release_iclog(log, iclog);
 	spin_unlock(&log->l_icloglock);
 
 	return error;
@@ -3053,7 +3028,7 @@
 		 * reference to the iclog.
 		 */
 		if (!atomic_add_unless(&iclog->ic_refcnt, -1, 1))
-			error = xlog_state_release_iclog(log, iclog, 0);
+			error = xlog_state_release_iclog(log, iclog);
 		spin_unlock(&log->l_icloglock);
 		if (error)
 			return error;
@@ -3904,7 +3879,10 @@
 	wake_up_all(&log->l_cilp->xc_start_wait);
 	wake_up_all(&log->l_cilp->xc_commit_wait);
 	spin_unlock(&log->l_cilp->xc_push_lock);
+
+	spin_lock(&log->l_icloglock);
 	xlog_state_shutdown_callbacks(log);
+	spin_unlock(&log->l_icloglock);
 
 	return log_error;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_log_cil.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_log_cil.c
@@ -681,11 +681,21 @@
 		 * The LSN we need to pass to the log items on transaction
 		 * commit is the LSN reported by the first log vector write, not
 		 * the commit lsn. If we use the commit record lsn then we can
-		 * move the tail beyond the grant write head.
+		 * move the grant write head beyond the tail LSN and overwrite
+		 * it.
 		 */
 		ctx->start_lsn = lsn;
 		wake_up_all(&cil->xc_start_wait);
 		spin_unlock(&cil->xc_push_lock);
+
+		/*
+		 * Make sure the metadata we are about to overwrite in the log
+		 * has been flushed to stable storage before this iclog is
+		 * issued.
+		 */
+		spin_lock(&cil->xc_log->l_icloglock);
+		iclog->ic_flags |= XLOG_ICL_NEED_FLUSH;
+		spin_unlock(&cil->xc_log->l_icloglock);
 		return;
 	}
 
@@ -864,10 +874,7 @@
 	struct xfs_trans_header thdr;
 	struct xfs_log_iovec	lhdr;
 	struct xfs_log_vec	lvhdr = { NULL };
-	xfs_lsn_t		preflush_tail_lsn;
 	xfs_csn_t		push_seq;
-	struct bio		bio;
-	DECLARE_COMPLETION_ONSTACK(bdev_flush);
 	bool			push_commit_stable;
 
 	new_ctx = xlog_cil_ctx_alloc();
@@ -938,23 +945,6 @@
 	spin_unlock(&cil->xc_push_lock);
 
 	/*
-	 * The CIL is stable at this point - nothing new will be added to it
-	 * because we hold the flush lock exclusively. Hence we can now issue
-	 * a cache flush to ensure all the completed metadata in the journal we
-	 * are about to overwrite is on stable storage.
-	 *
-	 * Because we are issuing this cache flush before we've written the
-	 * tail lsn to the iclog, we can have metadata IO completions move the
-	 * tail forwards between the completion of this flush and the iclog
-	 * being written. In this case, we need to re-issue the cache flush
-	 * before the iclog write. To detect whether the log tail moves, sample
-	 * the tail LSN *before* we issue the flush.
-	 */
-	preflush_tail_lsn = atomic64_read(&log->l_tail_lsn);
-	xfs_flush_bdev_async(&bio, log->l_mp->m_ddev_targp->bt_bdev,
-				&bdev_flush);
-
-	/*
 	 * Pull all the log vectors off the items in the CIL, and remove the
 	 * items from the CIL. We don't need the CIL lock here because it's only
 	 * needed on the transaction commit side which is currently locked out
@@ -1030,12 +1020,6 @@
 	lvhdr.lv_iovecp = &lhdr;
 	lvhdr.lv_next = ctx->lv_chain;
 
-	/*
-	 * Before we format and submit the first iclog, we have to ensure that
-	 * the metadata writeback ordering cache flush is complete.
-	 */
-	wait_for_completion(&bdev_flush);
-
 	error = xlog_cil_write_chain(ctx, &lvhdr);
 	if (error)
 		goto out_abort_free_ticket;
@@ -1094,7 +1078,7 @@
 	if (push_commit_stable &&
 	    ctx->commit_iclog->ic_state == XLOG_STATE_ACTIVE)
 		xlog_state_switch_iclogs(log, ctx->commit_iclog, 0);
-	xlog_state_release_iclog(log, ctx->commit_iclog, preflush_tail_lsn);
+	xlog_state_release_iclog(log, ctx->commit_iclog);
 
 	/* Not safe to reference ctx now! */
 
@@ -1115,7 +1099,7 @@
 		return;
 	}
 	spin_lock(&log->l_icloglock);
-	xlog_state_release_iclog(log, ctx->commit_iclog, 0);
+	xlog_state_release_iclog(log, ctx->commit_iclog);
 	/* Not safe to reference ctx now! */
 	spin_unlock(&log->l_icloglock);
 }
@@ -1442,9 +1426,9 @@
  */
 bool
 xfs_log_item_in_current_chkpt(
-	struct xfs_log_item *lip)
+	struct xfs_log_item	*lip)
 {
-	struct xfs_cil_ctx *ctx = lip->li_mountp->m_log->l_cilp->xc_ctx;
+	struct xfs_cil		*cil = lip->li_mountp->m_log->l_cilp;
 
 	if (list_empty(&lip->li_cil))
 		return false;
@@ -1454,7 +1438,7 @@
 	 * first checkpoint it is written to. Hence if it is different to the
 	 * current sequence, we're in a new checkpoint.
 	 */
-	return lip->li_seq == ctx->sequence;
+	return lip->li_seq == READ_ONCE(cil->xc_current_sequence);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_log_priv.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_log_priv.h
@@ -454,9 +454,6 @@
 	struct rw_semaphore	l_incompat_users;
 };
 
-#define XLOG_BUF_CANCEL_BUCKET(log, blkno) \
-	((log)->l_buf_cancel_table + ((uint64_t)blkno % XLOG_BC_TABLE_SIZE))
-
 /*
  * Bits for operational state
  */
@@ -524,8 +521,7 @@
 
 void xlog_state_switch_iclogs(struct xlog *log, struct xlog_in_core *iclog,
 		int eventual_size);
-int xlog_state_release_iclog(struct xlog *log, struct xlog_in_core *iclog,
-		xfs_lsn_t log_tail_lsn);
+int xlog_state_release_iclog(struct xlog *log, struct xlog_in_core *iclog);
 
 /*
  * When we crack an atomic LSN, we sample it first so that the value will not
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_log_recover.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_log_recover.c
@@ -27,7 +27,7 @@
 #include "xfs_buf_item.h"
 #include "xfs_ag.h"
 #include "xfs_quota.h"
-
+#include "xfs_reflink.h"
 
 #define BLK_AVG(blk1, blk2)	((blk1+blk2) >> 1)
 
@@ -2560,6 +2560,7 @@
 	for (lip = xfs_trans_ail_cursor_first(ailp, &cur, 0);
 	     lip != NULL;
 	     lip = xfs_trans_ail_cursor_next(ailp, &cur)) {
+		const struct xfs_item_ops	*ops;
 		/*
 		 * We're done when we see something other than an intent.
 		 * There should be no intents left in the AIL now.
@@ -2584,13 +2585,17 @@
 		 * deferred ops, you /must/ attach them to the capture list in
 		 * the recover routine or else those subsequent intents will be
 		 * replayed in the wrong order!
+		 *
+		 * The recovery function can free the log item, so we must not
+		 * access lip after it returns.
 		 */
 		spin_unlock(&ailp->ail_lock);
-		error = lip->li_ops->iop_recover(lip, &capture_list);
+		ops = lip->li_ops;
+		error = ops->iop_recover(lip, &capture_list);
 		spin_lock(&ailp->ail_lock);
 		if (error) {
 			trace_xlog_intent_recovery_failed(log->l_mp, error,
-					lip->li_ops->iop_recover);
+					ops->iop_recover);
 			break;
 		}
 	}
@@ -2739,6 +2744,7 @@
 	 * Call xlog_recover_clear_agi_bucket() to perform a transaction to
 	 * clear the inode pointer in the bucket.
 	 */
+	xfs_inodegc_flush(mp);
 	xlog_recover_clear_agi_bucket(mp, agno, bucket);
 	return NULLAGINO;
 }
@@ -2966,7 +2972,7 @@
 	int			error = 0, h_size, h_len;
 	int			error2 = 0;
 	int			bblks, split_bblks;
-	int			hblks, split_hblks, wrapped_hblks;
+	int			hblks = 1, split_hblks, wrapped_hblks;
 	int			i;
 	struct hlist_head	rhash[XLOG_RHASH_SIZE];
 	LIST_HEAD		(buffer_list);
@@ -3022,14 +3028,22 @@
 		if (error)
 			goto bread_err1;
 
-		hblks = xlog_logrec_hblks(log, rhead);
-		if (hblks != 1) {
-			kmem_free(hbp);
-			hbp = xlog_alloc_buffer(log, hblks);
+		/*
+		 * This open codes xlog_logrec_hblks so that we can reuse the
+		 * fixed up h_size value calculated above.  Without that we'd
+		 * still allocate the buffer based on the incorrect on-disk
+		 * size.
+		 */
+		if (h_size > XLOG_HEADER_CYCLE_SIZE &&
+		    (rhead->h_version & cpu_to_be32(XLOG_VERSION_2))) {
+			hblks = DIV_ROUND_UP(h_size, XLOG_HEADER_CYCLE_SIZE);
+			if (hblks > 1) {
+				kmem_free(hbp);
+				hbp = xlog_alloc_buffer(log, hblks);
+			}
 		}
 	} else {
 		ASSERT(log->l_sectBBsize == 1);
-		hblks = 1;
 		hbp = xlog_alloc_buffer(log, 1);
 		h_size = XLOG_BIG_RECORD_BSIZE;
 	}
@@ -3248,7 +3262,7 @@
 	xfs_daddr_t	head_blk,
 	xfs_daddr_t	tail_blk)
 {
-	int		error, i;
+	int		error;
 
 	ASSERT(head_blk != tail_blk);
 
@@ -3256,37 +3270,25 @@
 	 * First do a pass to find all of the cancelled buf log items.
 	 * Store them in the buf_cancel_table for use in the second pass.
 	 */
-	log->l_buf_cancel_table = kmem_zalloc(XLOG_BC_TABLE_SIZE *
-						 sizeof(struct list_head),
-						 0);
-	for (i = 0; i < XLOG_BC_TABLE_SIZE; i++)
-		INIT_LIST_HEAD(&log->l_buf_cancel_table[i]);
+	error = xlog_alloc_buf_cancel_table(log);
+	if (error)
+		return error;
 
 	error = xlog_do_recovery_pass(log, head_blk, tail_blk,
 				      XLOG_RECOVER_PASS1, NULL);
-	if (error != 0) {
-		kmem_free(log->l_buf_cancel_table);
-		log->l_buf_cancel_table = NULL;
-		return error;
-	}
+	if (error != 0)
+		goto out_cancel;
+
 	/*
 	 * Then do a second pass to actually recover the items in the log.
 	 * When it is complete free the table of buf cancel items.
 	 */
 	error = xlog_do_recovery_pass(log, head_blk, tail_blk,
 				      XLOG_RECOVER_PASS2, NULL);
-#ifdef DEBUG
-	if (!error) {
-		int	i;
-
-		for (i = 0; i < XLOG_BC_TABLE_SIZE; i++)
-			ASSERT(list_empty(&log->l_buf_cancel_table[i]));
-	}
-#endif	/* DEBUG */
-
-	kmem_free(log->l_buf_cancel_table);
-	log->l_buf_cancel_table = NULL;
-
+	if (!error)
+		xlog_check_buf_cancel_table(log);
+out_cancel:
+	xlog_free_buf_cancel_table(log);
 	return error;
 }
 
@@ -3502,6 +3504,28 @@
 
 	xlog_recover_process_iunlinks(log);
 	xlog_recover_check_summary(log);
+
+	/*
+	 * Recover any CoW staging blocks that are still referenced by the
+	 * ondisk refcount metadata.  During mount there cannot be any live
+	 * staging extents as we have not permitted any user modifications.
+	 * Therefore, it is safe to free them all right now, even on a
+	 * read-only mount.
+	 */
+	error = xfs_reflink_recover_cow(log->l_mp);
+	if (error) {
+		xfs_alert(log->l_mp,
+	"Failed to recover leftover CoW staging extents, err %d.",
+				error);
+		/*
+		 * If we get an error here, make sure the log is shut down
+		 * but return zero so that any log items committed since the
+		 * end of intents processing can be pushed through the CIL
+		 * and AIL.
+		 */
+		xfs_force_shutdown(log->l_mp, SHUTDOWN_LOG_IO_ERROR);
+	}
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_mount.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_mount.c
@@ -922,15 +922,6 @@
 			xfs_warn(mp,
 	"Unable to allocate reserve blocks. Continuing without reserve pool.");
 
-		/* Recover any CoW blocks that never got remapped. */
-		error = xfs_reflink_recover_cow(mp);
-		if (error) {
-			xfs_err(mp,
-	"Error %d recovering leftover CoW allocations.", error);
-			xfs_force_shutdown(mp, SHUTDOWN_CORRUPT_INCORE);
-			goto out_quota;
-		}
-
 		/* Reserve AG blocks for future btree expansion. */
 		error = xfs_fs_reserve_ag_blocks(mp);
 		if (error && error != -ENOSPC)
@@ -941,7 +932,6 @@
 
  out_agresv:
 	xfs_fs_unreserve_ag_blocks(mp);
- out_quota:
 	xfs_qm_unmount_quotas(mp);
  out_rtunmount:
 	xfs_rtunmount_inodes(mp);
@@ -1142,7 +1132,7 @@
 	 * problems (i.e. transaction abort, pagecache discards, etc.) than
 	 * slightly premature -ENOSPC.
 	 */
-	set_aside = mp->m_alloc_set_aside + atomic64_read(&mp->m_allocbt_blks);
+	set_aside = xfs_fdblocks_unavailable(mp);
 	percpu_counter_add_batch(&mp->m_fdblocks, delta, batch);
 	if (__percpu_counter_compare(&mp->m_fdblocks, set_aside,
 				     XFS_FDBLOCKS_BATCH) >= 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_mount.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_mount.h
@@ -61,11 +61,14 @@
  */
 struct xfs_inodegc {
 	struct llist_head	list;
-	struct work_struct	work;
+	struct delayed_work	work;
 
 	/* approximate count of inodes in the list */
 	unsigned int		items;
 	unsigned int		shrinker_hits;
+#if defined(DEBUG) || defined(XFS_WARN)
+	unsigned int		cpu;
+#endif
 };
 
 /*
@@ -478,6 +481,21 @@
  */
 #define XFS_FDBLOCKS_BATCH	1024
 
+/*
+ * Estimate the amount of free space that is not available to userspace and is
+ * not explicitly reserved from the incore fdblocks.  This includes:
+ *
+ * - The minimum number of blocks needed to support splitting a bmap btree
+ * - The blocks currently in use by the freespace btrees because they record
+ *   the actual blocks that will fill per-AG metadata space reservations
+ */
+static inline uint64_t
+xfs_fdblocks_unavailable(
+	struct xfs_mount	*mp)
+{
+	return mp->m_alloc_set_aside + atomic64_read(&mp->m_allocbt_blks);
+}
+
 extern int	xfs_mod_fdblocks(struct xfs_mount *mp, int64_t delta,
 				 bool reserved);
 extern int	xfs_mod_frextents(struct xfs_mount *mp, int64_t delta);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_pnfs.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_pnfs.c
@@ -164,10 +164,12 @@
 		 * that the blocks allocated and handed out to the client are
 		 * guaranteed to be present even after a server crash.
 		 */
-		error = xfs_update_prealloc_flags(ip,
-				XFS_PREALLOC_SET | XFS_PREALLOC_SYNC);
+		error = xfs_update_prealloc_flags(ip, XFS_PREALLOC_SET);
+		if (!error)
+			error = xfs_log_force_inode(ip);
 		if (error)
 			goto out_unlock;
+
 	} else {
 		xfs_iunlock(ip, lock_flags);
 	}
@@ -283,7 +285,8 @@
 	xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL);
 	xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
 
-	xfs_setattr_time(ip, iattr);
+	ASSERT(!(iattr->ia_valid & (ATTR_UID | ATTR_GID)));
+	setattr_copy(&init_user_ns, inode, iattr);
 	if (update_isize) {
 		i_size_write(inode, iattr->ia_size);
 		ip->i_disk_size = iattr->ia_size;
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_qm.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_qm.c
@@ -1244,6 +1244,13 @@
 			error = -EINVAL;
 			goto out_unlock;
 		}
+
+		if (!(bp->b_flags & _XBF_DELWRI_Q)) {
+			error = -EAGAIN;
+			xfs_buf_relse(bp);
+			goto out_unlock;
+		}
+
 		xfs_buf_unlock(bp);
 
 		xfs_buf_delwri_pushbuf(bp, buffer_list);
@@ -1317,8 +1324,15 @@
 
 	error = xfs_iwalk_threaded(mp, 0, 0, xfs_qm_dqusage_adjust, 0, true,
 			NULL);
-	if (error)
+	if (error) {
+		/*
+		 * The inode walk may have partially populated the dquot
+		 * caches.  We must purge them before disabling quota and
+		 * tearing down the quotainfo, or else the dquots will leak.
+		 */
+		xfs_qm_dqpurge_all(mp);
 		goto error_return;
+	}
 
 	/*
 	 * We've made all the changes that we need to make incore.  Flush them
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_qm_bhv.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_qm_bhv.c
@@ -19,28 +19,41 @@
 STATIC void
 xfs_fill_statvfs_from_dquot(
 	struct kstatfs		*statp,
+	struct xfs_inode	*ip,
 	struct xfs_dquot	*dqp)
 {
+	struct xfs_dquot_res	*blkres = &dqp->q_blk;
 	uint64_t		limit;
 
-	limit = dqp->q_blk.softlimit ?
-		dqp->q_blk.softlimit :
-		dqp->q_blk.hardlimit;
-	if (limit && statp->f_blocks > limit) {
-		statp->f_blocks = limit;
-		statp->f_bfree = statp->f_bavail =
-			(statp->f_blocks > dqp->q_blk.reserved) ?
-			 (statp->f_blocks - dqp->q_blk.reserved) : 0;
+	if (XFS_IS_REALTIME_MOUNT(ip->i_mount) &&
+	    (ip->i_diflags & (XFS_DIFLAG_RTINHERIT | XFS_DIFLAG_REALTIME)))
+		blkres = &dqp->q_rtb;
+
+	limit = blkres->softlimit ?
+		blkres->softlimit :
+		blkres->hardlimit;
+	if (limit) {
+		uint64_t	remaining = 0;
+
+		if (limit > blkres->reserved)
+			remaining = limit - blkres->reserved;
+
+		statp->f_blocks = min(statp->f_blocks, limit);
+		statp->f_bfree = min(statp->f_bfree, remaining);
+		statp->f_bavail = min(statp->f_bavail, remaining);
 	}
 
 	limit = dqp->q_ino.softlimit ?
 		dqp->q_ino.softlimit :
 		dqp->q_ino.hardlimit;
-	if (limit && statp->f_files > limit) {
-		statp->f_files = limit;
-		statp->f_ffree =
-			(statp->f_files > dqp->q_ino.reserved) ?
-			 (statp->f_files - dqp->q_ino.reserved) : 0;
+	if (limit) {
+		uint64_t	remaining = 0;
+
+		if (limit > dqp->q_ino.reserved)
+			remaining = limit - dqp->q_ino.reserved;
+
+		statp->f_files = min(statp->f_files, limit);
+		statp->f_ffree = min(statp->f_ffree, remaining);
 	}
 }
 
@@ -61,7 +74,7 @@
 	struct xfs_dquot	*dqp;
 
 	if (!xfs_qm_dqget(mp, ip->i_projid, XFS_DQTYPE_PROJ, false, &dqp)) {
-		xfs_fill_statvfs_from_dquot(statp, dqp);
+		xfs_fill_statvfs_from_dquot(statp, ip, dqp);
 		xfs_qm_dqput(dqp);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_qm_syscalls.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_qm_syscalls.c
@@ -481,9 +481,12 @@
 	struct xfs_dquot	*dqp;
 	int			error;
 
-	/* Flush inodegc work at the start of a quota reporting scan. */
+	/*
+	 * Expedite pending inodegc work at the start of a quota reporting
+	 * scan but don't block waiting for it to complete.
+	 */
 	if (id == 0)
-		xfs_inodegc_flush(mp);
+		xfs_inodegc_push(mp);
 
 	/*
 	 * Try to get the dquot. We don't want it allocated on disk, so don't
@@ -525,7 +528,7 @@
 
 	/* Flush inodegc work at the start of a quota reporting scan. */
 	if (*id == 0)
-		xfs_inodegc_flush(mp);
+		xfs_inodegc_push(mp);
 
 	error = xfs_qm_dqget_next(mp, *id, type, &dqp);
 	if (error)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_refcount_item.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_refcount_item.c
@@ -35,6 +35,7 @@
 xfs_cui_item_free(
 	struct xfs_cui_log_item	*cuip)
 {
+	kmem_free(cuip->cui_item.li_lv_shadow);
 	if (cuip->cui_format.cui_nextents > XFS_CUI_MAX_FAST_EXTENTS)
 		kmem_free(cuip);
 	else
@@ -204,6 +205,7 @@
 	struct xfs_cud_log_item	*cudp = CUD_ITEM(lip);
 
 	xfs_cui_release(cudp->cud_cuip);
+	kmem_free(cudp->cud_item.li_lv_shadow);
 	kmem_cache_free(xfs_cud_zone, cudp);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_reflink.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_reflink.c
@@ -340,9 +340,41 @@
 	return 0;
 }
 
-/* Allocate all CoW reservations covering a range of blocks in a file. */
-int
-xfs_reflink_allocate_cow(
+static int
+xfs_reflink_convert_unwritten(
+	struct xfs_inode	*ip,
+	struct xfs_bmbt_irec	*imap,
+	struct xfs_bmbt_irec	*cmap,
+	bool			convert_now)
+{
+	xfs_fileoff_t		offset_fsb = imap->br_startoff;
+	xfs_filblks_t		count_fsb = imap->br_blockcount;
+	int			error;
+
+	/*
+	 * cmap might larger than imap due to cowextsize hint.
+	 */
+	xfs_trim_extent(cmap, offset_fsb, count_fsb);
+
+	/*
+	 * COW fork extents are supposed to remain unwritten until we're ready
+	 * to initiate a disk write.  For direct I/O we are going to write the
+	 * data and need the conversion, but for buffered writes we're done.
+	 */
+	if (!convert_now || cmap->br_state == XFS_EXT_NORM)
+		return 0;
+
+	trace_xfs_reflink_convert_cow(ip, cmap);
+
+	error = xfs_reflink_convert_cow_locked(ip, offset_fsb, count_fsb);
+	if (!error)
+		cmap->br_state = XFS_EXT_NORM;
+
+	return error;
+}
+
+static int
+xfs_reflink_fill_cow_hole(
 	struct xfs_inode	*ip,
 	struct xfs_bmbt_irec	*imap,
 	struct xfs_bmbt_irec	*cmap,
@@ -351,25 +383,12 @@
 	bool			convert_now)
 {
 	struct xfs_mount	*mp = ip->i_mount;
-	xfs_fileoff_t		offset_fsb = imap->br_startoff;
-	xfs_filblks_t		count_fsb = imap->br_blockcount;
 	struct xfs_trans	*tp;
-	int			nimaps, error = 0;
-	bool			found;
 	xfs_filblks_t		resaligned;
-	xfs_extlen_t		resblks = 0;
-
-	ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL));
-	if (!ip->i_cowfp) {
-		ASSERT(!xfs_is_reflink_inode(ip));
-		xfs_ifork_init_cow(ip);
-	}
-
-	error = xfs_find_trim_cow_extent(ip, imap, cmap, shared, &found);
-	if (error || !*shared)
-		return error;
-	if (found)
-		goto convert;
+	xfs_extlen_t		resblks;
+	int			nimaps;
+	int			error;
+	bool			found;
 
 	resaligned = xfs_aligned_fsb_count(imap->br_startoff,
 		imap->br_blockcount, xfs_get_cowextsz_hint(ip));
@@ -385,17 +404,17 @@
 
 	*lockmode = XFS_ILOCK_EXCL;
 
-	/*
-	 * Check for an overlapping extent again now that we dropped the ilock.
-	 */
 	error = xfs_find_trim_cow_extent(ip, imap, cmap, shared, &found);
 	if (error || !*shared)
 		goto out_trans_cancel;
+
 	if (found) {
 		xfs_trans_cancel(tp);
 		goto convert;
 	}
 
+	ASSERT(cmap->br_startoff > imap->br_startoff);
+
 	/* Allocate the entire reservation as unwritten blocks. */
 	nimaps = 1;
 	error = xfs_bmapi_write(tp, ip, imap->br_startoff, imap->br_blockcount,
@@ -415,23 +434,135 @@
 	 */
 	if (nimaps == 0)
 		return -ENOSPC;
+
 convert:
-	xfs_trim_extent(cmap, offset_fsb, count_fsb);
-	/*
-	 * COW fork extents are supposed to remain unwritten until we're ready
-	 * to initiate a disk write.  For direct I/O we are going to write the
-	 * data and need the conversion, but for buffered writes we're done.
-	 */
-	if (!convert_now || cmap->br_state == XFS_EXT_NORM)
-		return 0;
-	trace_xfs_reflink_convert_cow(ip, cmap);
-	return xfs_reflink_convert_cow_locked(ip, offset_fsb, count_fsb);
+	return xfs_reflink_convert_unwritten(ip, imap, cmap, convert_now);
 
 out_trans_cancel:
 	xfs_trans_cancel(tp);
 	return error;
 }
 
+static int
+xfs_reflink_fill_delalloc(
+	struct xfs_inode	*ip,
+	struct xfs_bmbt_irec	*imap,
+	struct xfs_bmbt_irec	*cmap,
+	bool			*shared,
+	uint			*lockmode,
+	bool			convert_now)
+{
+	struct xfs_mount	*mp = ip->i_mount;
+	struct xfs_trans	*tp;
+	int			nimaps;
+	int			error;
+	bool			found;
+
+	do {
+		xfs_iunlock(ip, *lockmode);
+		*lockmode = 0;
+
+		error = xfs_trans_alloc_inode(ip, &M_RES(mp)->tr_write, 0, 0,
+				false, &tp);
+		if (error)
+			return error;
+
+		*lockmode = XFS_ILOCK_EXCL;
+
+		error = xfs_find_trim_cow_extent(ip, imap, cmap, shared,
+				&found);
+		if (error || !*shared)
+			goto out_trans_cancel;
+
+		if (found) {
+			xfs_trans_cancel(tp);
+			break;
+		}
+
+		ASSERT(isnullstartblock(cmap->br_startblock) ||
+		       cmap->br_startblock == DELAYSTARTBLOCK);
+
+		/*
+		 * Replace delalloc reservation with an unwritten extent.
+		 */
+		nimaps = 1;
+		error = xfs_bmapi_write(tp, ip, cmap->br_startoff,
+				cmap->br_blockcount,
+				XFS_BMAPI_COWFORK | XFS_BMAPI_PREALLOC, 0,
+				cmap, &nimaps);
+		if (error)
+			goto out_trans_cancel;
+
+		xfs_inode_set_cowblocks_tag(ip);
+		error = xfs_trans_commit(tp);
+		if (error)
+			return error;
+
+		/*
+		 * Allocation succeeded but the requested range was not even
+		 * partially satisfied?  Bail out!
+		 */
+		if (nimaps == 0)
+			return -ENOSPC;
+	} while (cmap->br_startoff + cmap->br_blockcount <= imap->br_startoff);
+
+	return xfs_reflink_convert_unwritten(ip, imap, cmap, convert_now);
+
+out_trans_cancel:
+	xfs_trans_cancel(tp);
+	return error;
+}
+
+/* Allocate all CoW reservations covering a range of blocks in a file. */
+int
+xfs_reflink_allocate_cow(
+	struct xfs_inode	*ip,
+	struct xfs_bmbt_irec	*imap,
+	struct xfs_bmbt_irec	*cmap,
+	bool			*shared,
+	uint			*lockmode,
+	bool			convert_now)
+{
+	int			error;
+	bool			found;
+
+	ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL));
+	if (!ip->i_cowfp) {
+		ASSERT(!xfs_is_reflink_inode(ip));
+		xfs_ifork_init_cow(ip);
+	}
+
+	error = xfs_find_trim_cow_extent(ip, imap, cmap, shared, &found);
+	if (error || !*shared)
+		return error;
+
+	/* CoW fork has a real extent */
+	if (found)
+		return xfs_reflink_convert_unwritten(ip, imap, cmap,
+				convert_now);
+
+	/*
+	 * CoW fork does not have an extent and data extent is shared.
+	 * Allocate a real extent in the CoW fork.
+	 */
+	if (cmap->br_startoff > imap->br_startoff)
+		return xfs_reflink_fill_cow_hole(ip, imap, cmap, shared,
+				lockmode, convert_now);
+
+	/*
+	 * CoW fork has a delalloc reservation. Replace it with a real extent.
+	 * There may or may not be a data fork mapping.
+	 */
+	if (isnullstartblock(cmap->br_startblock) ||
+	    cmap->br_startblock == DELAYSTARTBLOCK)
+		return xfs_reflink_fill_delalloc(ip, imap, cmap, shared,
+				lockmode, convert_now);
+
+	/* Shouldn't get here. */
+	ASSERT(0);
+	return -EFSCORRUPTED;
+}
+
 /*
  * Cancel CoW reservations for some block range of an inode.
  *
@@ -749,7 +880,10 @@
 }
 
 /*
- * Free leftover CoW reservations that didn't get cleaned out.
+ * Free all CoW staging blocks that are still referenced by the ondisk refcount
+ * metadata.  The ondisk metadata does not track which inode created the
+ * staging extent, so callers must ensure that there are no cached inodes with
+ * live CoW staging extents.
  */
 int
 xfs_reflink_recover_cow(
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_rmap_item.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_rmap_item.c
@@ -35,6 +35,7 @@
 xfs_rui_item_free(
 	struct xfs_rui_log_item	*ruip)
 {
+	kmem_free(ruip->rui_item.li_lv_shadow);
 	if (ruip->rui_format.rui_nextents > XFS_RUI_MAX_FAST_EXTENTS)
 		kmem_free(ruip);
 	else
@@ -227,6 +228,7 @@
 	struct xfs_rud_log_item	*rudp = RUD_ITEM(lip);
 
 	xfs_rui_release(rudp->rud_ruip);
+	kmem_free(rudp->rud_item.li_lv_shadow);
 	kmem_cache_free(xfs_rud_zone, rudp);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_super.c
@@ -642,7 +642,7 @@
 static void
 xfs_fs_dirty_inode(
 	struct inode			*inode,
-	int				flag)
+	int				flags)
 {
 	struct xfs_inode		*ip = XFS_I(inode);
 	struct xfs_mount		*mp = ip->i_mount;
@@ -650,7 +650,13 @@
 
 	if (!(inode->i_sb->s_flags & SB_LAZYTIME))
 		return;
-	if (flag != I_DIRTY_SYNC || !(inode->i_state & I_DIRTY_TIME))
+
+	/*
+	 * Only do the timestamp update if the inode is dirty (I_DIRTY_SYNC)
+	 * and has dirty timestamp (I_DIRTY_TIME). I_DIRTY_TIME can be passed
+	 * in flags possibly together with I_DIRTY_SYNC.
+	 */
+	if ((flags & ~I_DIRTY_TIME) != I_DIRTY_SYNC || !(flags & I_DIRTY_TIME))
 		return;
 
 	if (xfs_trans_alloc(mp, &M_RES(mp)->tr_fsyncts, 0, 0, 0, &tp))
@@ -729,6 +735,7 @@
 	int			wait)
 {
 	struct xfs_mount	*mp = XFS_M(sb);
+	int			error;
 
 	trace_xfs_fs_sync_fs(mp, __return_address);
 
@@ -738,7 +745,10 @@
 	if (!wait)
 		return 0;
 
-	xfs_log_force(mp, XFS_LOG_SYNC);
+	error = xfs_log_force(mp, XFS_LOG_SYNC);
+	if (error)
+		return error;
+
 	if (laptop_mode) {
 		/*
 		 * The disk must be active because we're syncing.
@@ -785,8 +795,11 @@
 	xfs_extlen_t		lsize;
 	int64_t			ffree;
 
-	/* Wait for whatever inactivations are in progress. */
-	xfs_inodegc_flush(mp);
+	/*
+	 * Expedite background inodegc but don't wait. We do not want to block
+	 * here waiting hours for a billion extent file to be truncated.
+	 */
+	xfs_inodegc_push(mp);
 
 	statp->f_type = XFS_SUPER_MAGIC;
 	statp->f_namelen = MAXNAMELEN - 1;
@@ -824,12 +837,6 @@
 	ffree = statp->f_files - (icount - ifree);
 	statp->f_ffree = max_t(int64_t, ffree, 0);
 
-
-	if ((ip->i_diflags & XFS_DIFLAG_PROJINHERIT) &&
-	    ((mp->m_qflags & (XFS_PQUOTA_ACCT|XFS_PQUOTA_ENFD))) ==
-			      (XFS_PQUOTA_ACCT|XFS_PQUOTA_ENFD))
-		xfs_qm_statvfs(ip, statp);
-
 	if (XFS_IS_REALTIME_MOUNT(mp) &&
 	    (ip->i_diflags & (XFS_DIFLAG_RTINHERIT | XFS_DIFLAG_REALTIME))) {
 		statp->f_blocks = sbp->sb_rblocks;
@@ -837,6 +844,11 @@
 			sbp->sb_frextents * sbp->sb_rextsize;
 	}
 
+	if ((ip->i_diflags & XFS_DIFLAG_PROJINHERIT) &&
+	    ((mp->m_qflags & (XFS_PQUOTA_ACCT|XFS_PQUOTA_ENFD))) ==
+			      (XFS_PQUOTA_ACCT|XFS_PQUOTA_ENFD))
+		xfs_qm_statvfs(ip, statp);
+
 	return 0;
 }
 
@@ -1049,9 +1061,12 @@
 
 	for_each_possible_cpu(cpu) {
 		gc = per_cpu_ptr(mp->m_inodegc, cpu);
+#if defined(DEBUG) || defined(XFS_WARN)
+		gc->cpu = cpu;
+#endif
 		init_llist_head(&gc->list);
 		gc->items = 0;
-		INIT_WORK(&gc->work, xfs_inodegc_worker);
+		INIT_DELAYED_WORK(&gc->work, xfs_inodegc_worker);
 	}
 	return 0;
 }
@@ -1420,6 +1435,18 @@
 
 	mp->m_super = sb;
 
+	/*
+	 * Copy VFS mount flags from the context now that all parameter parsing
+	 * is guaranteed to have been completed by either the old mount API or
+	 * the newer fsopen/fsconfig API.
+	 */
+	if (fc->sb_flags & SB_RDONLY)
+		set_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
+	if (fc->sb_flags & SB_DIRSYNC)
+		mp->m_features |= XFS_FEAT_DIRSYNC;
+	if (fc->sb_flags & SB_SYNCHRONOUS)
+		mp->m_features |= XFS_FEAT_WSYNC;
+
 	error = xfs_fs_validate_params(mp);
 	if (error)
 		goto out_free_names;
@@ -1738,15 +1765,6 @@
 	 */
 	xfs_restore_resvblks(mp);
 	xfs_log_work_queue(mp);
-
-	/* Recover any CoW blocks that never got remapped. */
-	error = xfs_reflink_recover_cow(mp);
-	if (error) {
-		xfs_err(mp,
-			"Error %d recovering leftover CoW allocations.", error);
-		xfs_force_shutdown(mp, SHUTDOWN_CORRUPT_INCORE);
-		return error;
-	}
 	xfs_blockgc_start(mp);
 
 	/* Create the per-AG metadata reservation pool .*/
@@ -1764,7 +1782,15 @@
 xfs_remount_ro(
 	struct xfs_mount	*mp)
 {
-	int error;
+	struct xfs_icwalk	icw = {
+		.icw_flags	= XFS_ICWALK_FLAG_SYNC,
+	};
+	int			error;
+
+	/* Flush all the dirty data to disk. */
+	error = sync_filesystem(mp->m_super);
+	if (error)
+		return error;
 
 	/*
 	 * Cancel background eofb scanning so it cannot race with the final
@@ -1772,8 +1798,13 @@
 	 */
 	xfs_blockgc_stop(mp);
 
-	/* Get rid of any leftover CoW reservations... */
-	error = xfs_blockgc_free_space(mp, NULL);
+	/*
+	 * Clear out all remaining COW staging extents and speculative post-EOF
+	 * preallocations so that we don't leave inodes requiring inactivation
+	 * cleanups during reclaim on a read-only mount.  We must process every
+	 * cached inode, so this requires a synchronous cache scan.
+	 */
+	error = xfs_blockgc_free_space(mp, &icw);
 	if (error) {
 		xfs_force_shutdown(mp, SHUTDOWN_CORRUPT_INCORE);
 		return error;
@@ -1839,8 +1870,6 @@
 	if (error)
 		return error;
 
-	sync_filesystem(mp->m_super);
-
 	/* inode32 -> inode64 */
 	if (xfs_has_small_inums(mp) && !xfs_has_small_inums(new_mp)) {
 		mp->m_features &= ~XFS_FEAT_SMALL_INUMS;
@@ -1892,6 +1921,11 @@
 	.free        = xfs_fs_free,
 };
 
+/*
+ * WARNING: do not initialise any parameters in this function that depend on
+ * mount option parsing having already been performed as this can be called from
+ * fsopen() before any parameters have been set.
+ */
 static int xfs_init_fs_context(
 	struct fs_context	*fc)
 {
@@ -1924,16 +1958,6 @@
 	mp->m_logbsize = -1;
 	mp->m_allocsize_log = 16; /* 64k */
 
-	/*
-	 * Copy binary VFS mount flags we are interested in.
-	 */
-	if (fc->sb_flags & SB_RDONLY)
-		set_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
-	if (fc->sb_flags & SB_DIRSYNC)
-		mp->m_features |= XFS_FEAT_DIRSYNC;
-	if (fc->sb_flags & SB_SYNCHRONOUS)
-		mp->m_features |= XFS_FEAT_WSYNC;
-
 	fc->s_fs_info = mp;
 	fc->ops = &xfs_context_ops;
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_symlink.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_symlink.c
@@ -22,6 +22,7 @@
 #include "xfs_trace.h"
 #include "xfs_trans.h"
 #include "xfs_ialloc.h"
+#include "xfs_error.h"
 
 /* ----- Kernel only functions below ----- */
 int
@@ -96,17 +97,15 @@
 
 int
 xfs_readlink(
-	struct xfs_inode *ip,
-	char		*link)
+	struct xfs_inode	*ip,
+	char			*link)
 {
-	struct xfs_mount *mp = ip->i_mount;
-	xfs_fsize_t	pathlen;
-	int		error = 0;
+	struct xfs_mount	*mp = ip->i_mount;
+	xfs_fsize_t		pathlen;
+	int			error = -EFSCORRUPTED;
 
 	trace_xfs_readlink(ip);
 
-	ASSERT(ip->i_df.if_format != XFS_DINODE_FMT_LOCAL);
-
 	if (xfs_is_shutdown(mp))
 		return -EIO;
 
@@ -121,12 +120,22 @@
 			 __func__, (unsigned long long) ip->i_ino,
 			 (long long) pathlen);
 		ASSERT(0);
-		error = -EFSCORRUPTED;
 		goto out;
 	}
 
-
-	error = xfs_readlink_bmap_ilocked(ip, link);
+	if (ip->i_df.if_format == XFS_DINODE_FMT_LOCAL) {
+		/*
+		 * The VFS crashes on a NULL pointer, so return -EFSCORRUPTED
+		 * if if_data is junk.
+		 */
+		if (XFS_IS_CORRUPT(ip->i_mount, !ip->i_df.if_u1.if_data))
+			goto out;
+
+		memcpy(link, ip->i_df.if_u1.if_data, pathlen + 1);
+		error = 0;
+	} else {
+		error = xfs_readlink_bmap_ilocked(ip, link);
+	}
 
  out:
 	xfs_iunlock(ip, XFS_ILOCK_SHARED);
@@ -184,8 +193,8 @@
 	/*
 	 * Make sure that we have allocated dquot(s) on disk.
 	 */
-	error = xfs_qm_vop_dqalloc(dp, mapped_fsuid(mnt_userns),
-			mapped_fsgid(mnt_userns), prid,
+	error = xfs_qm_vop_dqalloc(dp, mapped_fsuid(mnt_userns, &init_user_ns),
+			mapped_fsgid(mnt_userns, &init_user_ns), prid,
 			XFS_QMOPT_QUOTALL | XFS_QMOPT_INHERIT,
 			&udqp, &gdqp, &pdqp);
 	if (error)
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_sysfs.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_sysfs.h
@@ -33,10 +33,15 @@
 	const char		*name)
 {
 	struct kobject		*parent;
+	int err;
 
 	parent = parent_kobj ? &parent_kobj->kobject : NULL;
 	init_completion(&kobj->complete);
-	return kobject_init_and_add(&kobj->kobject, ktype, parent, "%s", name);
+	err = kobject_init_and_add(&kobj->kobject, ktype, parent, "%s", name);
+	if (err)
+		kobject_put(&kobj->kobject);
+
+	return err;
 }
 
 static inline void
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_trace.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_trace.h
@@ -240,6 +240,7 @@
 	TP_PROTO(struct xfs_mount *mp, void *caller_ip), \
 	TP_ARGS(mp, caller_ip))
 DEFINE_FS_EVENT(xfs_inodegc_flush);
+DEFINE_FS_EVENT(xfs_inodegc_push);
 DEFINE_FS_EVENT(xfs_inodegc_start);
 DEFINE_FS_EVENT(xfs_inodegc_stop);
 DEFINE_FS_EVENT(xfs_inodegc_queue);
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_trans.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_trans.c
@@ -1201,3 +1201,89 @@
 	xfs_trans_cancel(tp);
 	return error;
 }
+
+/*
+ * Allocate an transaction, lock and join the directory and child inodes to it,
+ * and reserve quota for a directory update.  If there isn't sufficient space,
+ * @dblocks will be set to zero for a reservationless directory update and
+ * @nospace_error will be set to a negative errno describing the space
+ * constraint we hit.
+ *
+ * The caller must ensure that the on-disk dquots attached to this inode have
+ * already been allocated and initialized.  The ILOCKs will be dropped when the
+ * transaction is committed or cancelled.
+ */
+int
+xfs_trans_alloc_dir(
+	struct xfs_inode	*dp,
+	struct xfs_trans_res	*resv,
+	struct xfs_inode	*ip,
+	unsigned int		*dblocks,
+	struct xfs_trans	**tpp,
+	int			*nospace_error)
+{
+	struct xfs_trans	*tp;
+	struct xfs_mount	*mp = ip->i_mount;
+	unsigned int		resblks;
+	bool			retried = false;
+	int			error;
+
+retry:
+	*nospace_error = 0;
+	resblks = *dblocks;
+	error = xfs_trans_alloc(mp, resv, resblks, 0, 0, &tp);
+	if (error == -ENOSPC) {
+		*nospace_error = error;
+		resblks = 0;
+		error = xfs_trans_alloc(mp, resv, resblks, 0, 0, &tp);
+	}
+	if (error)
+		return error;
+
+	xfs_lock_two_inodes(dp, XFS_ILOCK_EXCL, ip, XFS_ILOCK_EXCL);
+
+	xfs_trans_ijoin(tp, dp, XFS_ILOCK_EXCL);
+	xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL);
+
+	error = xfs_qm_dqattach_locked(dp, false);
+	if (error) {
+		/* Caller should have allocated the dquots! */
+		ASSERT(error != -ENOENT);
+		goto out_cancel;
+	}
+
+	error = xfs_qm_dqattach_locked(ip, false);
+	if (error) {
+		/* Caller should have allocated the dquots! */
+		ASSERT(error != -ENOENT);
+		goto out_cancel;
+	}
+
+	if (resblks == 0)
+		goto done;
+
+	error = xfs_trans_reserve_quota_nblks(tp, dp, resblks, 0, false);
+	if (error == -EDQUOT || error == -ENOSPC) {
+		if (!retried) {
+			xfs_trans_cancel(tp);
+			xfs_blockgc_free_quota(dp, 0);
+			retried = true;
+			goto retry;
+		}
+
+		*nospace_error = error;
+		resblks = 0;
+		error = 0;
+	}
+	if (error)
+		goto out_cancel;
+
+done:
+	*tpp = tp;
+	*dblocks = resblks;
+	return 0;
+
+out_cancel:
+	xfs_trans_cancel(tp);
+	return error;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_trans.h
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_trans.h
@@ -265,6 +265,9 @@
 int xfs_trans_alloc_ichange(struct xfs_inode *ip, struct xfs_dquot *udqp,
 		struct xfs_dquot *gdqp, struct xfs_dquot *pdqp, bool force,
 		struct xfs_trans **tpp);
+int xfs_trans_alloc_dir(struct xfs_inode *dp, struct xfs_trans_res *resv,
+		struct xfs_inode *ip, unsigned int *dblocks,
+		struct xfs_trans **tpp, int *nospace_error);
 
 static inline void
 xfs_trans_set_context(
--- linux-xilinx-zynqmp-5.15.0.orig/fs/xfs/xfs_trans_dquot.c
+++ linux-xilinx-zynqmp-5.15.0/fs/xfs/xfs_trans_dquot.c
@@ -603,7 +603,6 @@
 			return QUOTA_NL_ISOFTLONGWARN;
 		}
 
-		res->warnings++;
 		return QUOTA_NL_ISOFTWARN;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/fs/zonefs/super.c
+++ linux-xilinx-zynqmp-5.15.0/fs/zonefs/super.c
@@ -35,6 +35,17 @@
 
 	lockdep_assert_held(&zi->i_truncate_mutex);
 
+	/*
+	 * With ZNS drives, closing an explicitly open zone that has not been
+	 * written will change the zone state to "closed", that is, the zone
+	 * will remain active. Since this can then cause failure of explicit
+	 * open operation on other zones if the drive active zone resources
+	 * are exceeded, make sure that the zone does not remain active by
+	 * resetting it.
+	 */
+	if (op == REQ_OP_ZONE_CLOSE && !zi->i_wpoffset)
+		op = REQ_OP_ZONE_RESET;
+
 	trace_zonefs_zone_mgmt(inode, op);
 	ret = blkdev_zone_mgmt(inode->i_sb->s_bdev, op, zi->i_zsector,
 			       zi->i_zone_size >> SECTOR_SHIFT, GFP_NOFS);
@@ -61,15 +72,51 @@
 		zi->i_flags &= ~ZONEFS_ZONE_OPEN;
 }
 
-static int zonefs_iomap_begin(struct inode *inode, loff_t offset, loff_t length,
-			      unsigned int flags, struct iomap *iomap,
-			      struct iomap *srcmap)
+static int zonefs_read_iomap_begin(struct inode *inode, loff_t offset,
+				   loff_t length, unsigned int flags,
+				   struct iomap *iomap, struct iomap *srcmap)
+{
+	struct zonefs_inode_info *zi = ZONEFS_I(inode);
+	struct super_block *sb = inode->i_sb;
+	loff_t isize;
+
+	/*
+	 * All blocks are always mapped below EOF. If reading past EOF,
+	 * act as if there is a hole up to the file maximum size.
+	 */
+	mutex_lock(&zi->i_truncate_mutex);
+	iomap->bdev = inode->i_sb->s_bdev;
+	iomap->offset = ALIGN_DOWN(offset, sb->s_blocksize);
+	isize = i_size_read(inode);
+	if (iomap->offset >= isize) {
+		iomap->type = IOMAP_HOLE;
+		iomap->addr = IOMAP_NULL_ADDR;
+		iomap->length = length;
+	} else {
+		iomap->type = IOMAP_MAPPED;
+		iomap->addr = (zi->i_zsector << SECTOR_SHIFT) + iomap->offset;
+		iomap->length = isize - iomap->offset;
+	}
+	mutex_unlock(&zi->i_truncate_mutex);
+
+	trace_zonefs_iomap_begin(inode, iomap);
+
+	return 0;
+}
+
+static const struct iomap_ops zonefs_read_iomap_ops = {
+	.iomap_begin	= zonefs_read_iomap_begin,
+};
+
+static int zonefs_write_iomap_begin(struct inode *inode, loff_t offset,
+				    loff_t length, unsigned int flags,
+				    struct iomap *iomap, struct iomap *srcmap)
 {
 	struct zonefs_inode_info *zi = ZONEFS_I(inode);
 	struct super_block *sb = inode->i_sb;
 	loff_t isize;
 
-	/* All I/Os should always be within the file maximum size */
+	/* All write I/Os should always be within the file maximum size */
 	if (WARN_ON_ONCE(offset + length > zi->i_max_size))
 		return -EIO;
 
@@ -79,7 +126,7 @@
 	 * operation.
 	 */
 	if (WARN_ON_ONCE(zi->i_ztype == ZONEFS_ZTYPE_SEQ &&
-			 (flags & IOMAP_WRITE) && !(flags & IOMAP_DIRECT)))
+			 !(flags & IOMAP_DIRECT)))
 		return -EIO;
 
 	/*
@@ -88,47 +135,44 @@
 	 * write pointer) and unwriten beyond.
 	 */
 	mutex_lock(&zi->i_truncate_mutex);
+	iomap->bdev = inode->i_sb->s_bdev;
+	iomap->offset = ALIGN_DOWN(offset, sb->s_blocksize);
+	iomap->addr = (zi->i_zsector << SECTOR_SHIFT) + iomap->offset;
 	isize = i_size_read(inode);
-	if (offset >= isize)
+	if (iomap->offset >= isize) {
 		iomap->type = IOMAP_UNWRITTEN;
-	else
+		iomap->length = zi->i_max_size - iomap->offset;
+	} else {
 		iomap->type = IOMAP_MAPPED;
-	if (flags & IOMAP_WRITE)
-		length = zi->i_max_size - offset;
-	else
-		length = min(length, isize - offset);
+		iomap->length = isize - iomap->offset;
+	}
 	mutex_unlock(&zi->i_truncate_mutex);
 
-	iomap->offset = ALIGN_DOWN(offset, sb->s_blocksize);
-	iomap->length = ALIGN(offset + length, sb->s_blocksize) - iomap->offset;
-	iomap->bdev = inode->i_sb->s_bdev;
-	iomap->addr = (zi->i_zsector << SECTOR_SHIFT) + iomap->offset;
-
 	trace_zonefs_iomap_begin(inode, iomap);
 
 	return 0;
 }
 
-static const struct iomap_ops zonefs_iomap_ops = {
-	.iomap_begin	= zonefs_iomap_begin,
+static const struct iomap_ops zonefs_write_iomap_ops = {
+	.iomap_begin	= zonefs_write_iomap_begin,
 };
 
 static int zonefs_readpage(struct file *unused, struct page *page)
 {
-	return iomap_readpage(page, &zonefs_iomap_ops);
+	return iomap_readpage(page, &zonefs_read_iomap_ops);
 }
 
 static void zonefs_readahead(struct readahead_control *rac)
 {
-	iomap_readahead(rac, &zonefs_iomap_ops);
+	iomap_readahead(rac, &zonefs_read_iomap_ops);
 }
 
 /*
  * Map blocks for page writeback. This is used only on conventional zone files,
  * which implies that the page range can only be within the fixed inode size.
  */
-static int zonefs_map_blocks(struct iomap_writepage_ctx *wpc,
-			     struct inode *inode, loff_t offset)
+static int zonefs_write_map_blocks(struct iomap_writepage_ctx *wpc,
+				   struct inode *inode, loff_t offset)
 {
 	struct zonefs_inode_info *zi = ZONEFS_I(inode);
 
@@ -142,12 +186,12 @@
 	    offset < wpc->iomap.offset + wpc->iomap.length)
 		return 0;
 
-	return zonefs_iomap_begin(inode, offset, zi->i_max_size - offset,
-				  IOMAP_WRITE, &wpc->iomap, NULL);
+	return zonefs_write_iomap_begin(inode, offset, zi->i_max_size - offset,
+					IOMAP_WRITE, &wpc->iomap, NULL);
 }
 
 static const struct iomap_writeback_ops zonefs_writeback_ops = {
-	.map_blocks		= zonefs_map_blocks,
+	.map_blocks		= zonefs_write_map_blocks,
 };
 
 static int zonefs_writepage(struct page *page, struct writeback_control *wbc)
@@ -177,7 +221,8 @@
 		return -EINVAL;
 	}
 
-	return iomap_swapfile_activate(sis, swap_file, span, &zonefs_iomap_ops);
+	return iomap_swapfile_activate(sis, swap_file, span,
+				       &zonefs_read_iomap_ops);
 }
 
 static const struct address_space_operations zonefs_file_aops = {
@@ -282,16 +327,18 @@
 	}
 }
 
-struct zonefs_ioerr_data {
-	struct inode	*inode;
-	bool		write;
-};
-
 static int zonefs_io_error_cb(struct blk_zone *zone, unsigned int idx,
 			      void *data)
 {
-	struct zonefs_ioerr_data *err = data;
-	struct inode *inode = err->inode;
+	struct blk_zone *z = data;
+
+	*z = *zone;
+	return 0;
+}
+
+static void zonefs_handle_io_error(struct inode *inode, struct blk_zone *zone,
+				   bool write)
+{
 	struct zonefs_inode_info *zi = ZONEFS_I(inode);
 	struct super_block *sb = inode->i_sb;
 	struct zonefs_sb_info *sbi = ZONEFS_SB(sb);
@@ -307,8 +354,8 @@
 	isize = i_size_read(inode);
 	if (zone->cond != BLK_ZONE_COND_OFFLINE &&
 	    zone->cond != BLK_ZONE_COND_READONLY &&
-	    !err->write && isize == data_size)
-		return 0;
+	    !write && isize == data_size)
+		return;
 
 	/*
 	 * At this point, we detected either a bad zone or an inconsistency
@@ -329,8 +376,9 @@
 	 * In all cases, warn about inode size inconsistency and handle the
 	 * IO error according to the zone condition and to the mount options.
 	 */
-	if (zi->i_ztype == ZONEFS_ZTYPE_SEQ && isize != data_size)
-		zonefs_warn(sb, "inode %lu: invalid size %lld (should be %lld)\n",
+	if (isize != data_size)
+		zonefs_warn(sb,
+			    "inode %lu: invalid size %lld (should be %lld)\n",
 			    inode->i_ino, isize, data_size);
 
 	/*
@@ -357,6 +405,10 @@
 			data_size = zonefs_check_zone_condition(inode, zone,
 								false, false);
 		}
+	} else if (sbi->s_mount_opts & ZONEFS_MNTOPT_ERRORS_RO &&
+		   data_size > isize) {
+		/* Do not expose garbage data */
+		data_size = isize;
 	}
 
 	/*
@@ -386,8 +438,6 @@
 	zonefs_update_stats(inode, data_size);
 	zonefs_i_size_write(inode, data_size);
 	zi->i_wpoffset = data_size;
-
-	return 0;
 }
 
 /*
@@ -401,17 +451,27 @@
 {
 	struct zonefs_inode_info *zi = ZONEFS_I(inode);
 	struct super_block *sb = inode->i_sb;
-	struct zonefs_sb_info *sbi = ZONEFS_SB(sb);
 	unsigned int noio_flag;
-	unsigned int nr_zones =
-		zi->i_zone_size >> (sbi->s_zone_sectors_shift + SECTOR_SHIFT);
-	struct zonefs_ioerr_data err = {
-		.inode = inode,
-		.write = write,
-	};
+	struct blk_zone zone;
 	int ret;
 
 	/*
+	 * Conventional zone have no write pointer and cannot become read-only
+	 * or offline. So simply fake a report for a single or aggregated zone
+	 * and let zonefs_handle_io_error() correct the zone inode information
+	 * according to the mount options.
+	 */
+	if (zi->i_ztype != ZONEFS_ZTYPE_SEQ) {
+		zone.start = zi->i_zsector;
+		zone.len = zi->i_max_size >> SECTOR_SHIFT;
+		zone.wp = zone.start + zone.len;
+		zone.type = BLK_ZONE_TYPE_CONVENTIONAL;
+		zone.cond = BLK_ZONE_COND_NOT_WP;
+		zone.capacity = zone.len;
+		goto handle_io_error;
+	}
+
+	/*
 	 * Memory allocations in blkdev_report_zones() can trigger a memory
 	 * reclaim which may in turn cause a recursion into zonefs as well as
 	 * struct request allocations for the same device. The former case may
@@ -420,12 +480,19 @@
 	 * the GFP_NOIO context avoids both problems.
 	 */
 	noio_flag = memalloc_noio_save();
-	ret = blkdev_report_zones(sb->s_bdev, zi->i_zsector, nr_zones,
-				  zonefs_io_error_cb, &err);
-	if (ret != nr_zones)
+	ret = blkdev_report_zones(sb->s_bdev, zi->i_zsector, 1,
+				  zonefs_io_error_cb, &zone);
+	memalloc_noio_restore(noio_flag);
+	if (ret != 1) {
 		zonefs_err(sb, "Get inode %lu zone information failed %d\n",
 			   inode->i_ino, ret);
-	memalloc_noio_restore(noio_flag);
+		zonefs_warn(sb, "remounting filesystem read-only\n");
+		sb->s_flags |= SB_RDONLY;
+		return;
+	}
+
+handle_io_error:
+	zonefs_handle_io_error(inode, &zone, write);
 }
 
 static void zonefs_io_error(struct inode *inode, bool write)
@@ -596,7 +663,7 @@
 
 	/* Serialize against truncates */
 	filemap_invalidate_lock_shared(inode->i_mapping);
-	ret = iomap_page_mkwrite(vmf, &zonefs_iomap_ops);
+	ret = iomap_page_mkwrite(vmf, &zonefs_write_iomap_ops);
 	filemap_invalidate_unlock_shared(inode->i_mapping);
 
 	sb_end_pagefault(inode->i_sb);
@@ -678,16 +745,29 @@
 	struct inode *inode = file_inode(iocb->ki_filp);
 	struct zonefs_inode_info *zi = ZONEFS_I(inode);
 	struct block_device *bdev = inode->i_sb->s_bdev;
-	unsigned int max;
+	unsigned int max = bdev_max_zone_append_sectors(bdev);
+	pgoff_t start, end;
 	struct bio *bio;
 	ssize_t size;
 	int nr_pages;
 	ssize_t ret;
 
-	max = queue_max_zone_append_sectors(bdev_get_queue(bdev));
 	max = ALIGN_DOWN(max << SECTOR_SHIFT, inode->i_sb->s_blocksize);
 	iov_iter_truncate(from, max);
 
+	/*
+	 * If the inode block size (zone write granularity) is smaller than the
+	 * page size, we may be appending data belonging to the last page of the
+	 * inode straddling inode->i_size, with that page already cached due to
+	 * a buffered read or readahead. So make sure to invalidate that page.
+	 * This will always be a no-op for the case where the block size is
+	 * equal to the page size.
+	 */
+	start = iocb->ki_pos >> PAGE_SHIFT;
+	end = (iocb->ki_pos + iov_iter_count(from) - 1) >> PAGE_SHIFT;
+	if (invalidate_inode_pages2_range(inode->i_mapping, start, end))
+		return -EBUSY;
+
 	nr_pages = iov_iter_npages(from, BIO_MAX_VECS);
 	if (!nr_pages)
 		return 0;
@@ -713,6 +793,24 @@
 
 	ret = submit_bio_wait(bio);
 
+	/*
+	 * If the file zone was written underneath the file system, the zone
+	 * write pointer may not be where we expect it to be, but the zone
+	 * append write can still succeed. So check manually that we wrote where
+	 * we intended to, that is, at zi->i_wpoffset.
+	 */
+	if (!ret) {
+		sector_t wpsector =
+			zi->i_zsector + (zi->i_wpoffset >> SECTOR_SHIFT);
+
+		if (bio->bi_iter.bi_sector != wpsector) {
+			zonefs_warn(inode->i_sb,
+				"Corrupted write pointer %llu for zone at %llu\n",
+				bio->bi_iter.bi_sector, zi->i_zsector);
+			ret = -EIO;
+		}
+	}
+
 	zonefs_file_write_dio_end_io(iocb, size, ret, 0);
 	trace_zonefs_file_dio_append(inode, size, ret);
 
@@ -851,8 +949,8 @@
 	if (append)
 		ret = zonefs_file_dio_append(iocb, from);
 	else
-		ret = iomap_dio_rw(iocb, from, &zonefs_iomap_ops,
-				   &zonefs_write_dio_ops, 0);
+		ret = iomap_dio_rw(iocb, from, &zonefs_write_iomap_ops,
+				   &zonefs_write_dio_ops, 0, 0);
 	if (zi->i_ztype == ZONEFS_ZTYPE_SEQ &&
 	    (ret > 0 || ret == -EIOCBQUEUED)) {
 		if (ret > 0)
@@ -893,7 +991,7 @@
 	if (ret <= 0)
 		goto inode_unlock;
 
-	ret = iomap_file_buffered_write(iocb, from, &zonefs_iomap_ops);
+	ret = iomap_file_buffered_write(iocb, from, &zonefs_write_iomap_ops);
 	if (ret > 0)
 		iocb->ki_pos += ret;
 	else if (ret == -EIO)
@@ -986,8 +1084,8 @@
 			goto inode_unlock;
 		}
 		file_accessed(iocb->ki_filp);
-		ret = iomap_dio_rw(iocb, to, &zonefs_iomap_ops,
-				   &zonefs_read_dio_ops, 0);
+		ret = iomap_dio_rw(iocb, to, &zonefs_read_iomap_ops,
+				   &zonefs_read_dio_ops, 0, 0);
 	} else {
 		ret = generic_file_read_iter(iocb, to);
 		if (ret == -EIO)
@@ -1144,6 +1242,7 @@
 	inode_init_once(&zi->i_vnode);
 	mutex_init(&zi->i_truncate_mutex);
 	zi->i_wr_refcnt = 0;
+	zi->i_flags = 0;
 
 	return &zi->i_vnode;
 }
@@ -1295,12 +1394,13 @@
 	inc_nlink(parent);
 }
 
-static void zonefs_init_file_inode(struct inode *inode, struct blk_zone *zone,
-				   enum zonefs_ztype type)
+static int zonefs_init_file_inode(struct inode *inode, struct blk_zone *zone,
+				  enum zonefs_ztype type)
 {
 	struct super_block *sb = inode->i_sb;
 	struct zonefs_sb_info *sbi = ZONEFS_SB(sb);
 	struct zonefs_inode_info *zi = ZONEFS_I(inode);
+	int ret = 0;
 
 	inode->i_ino = zone->start >> sbi->s_zone_sectors_shift;
 	inode->i_mode = S_IFREG | sbi->s_perm;
@@ -1308,6 +1408,14 @@
 	zi->i_ztype = type;
 	zi->i_zsector = zone->start;
 	zi->i_zone_size = zone->len << SECTOR_SHIFT;
+	if (zi->i_zone_size > bdev_zone_sectors(sb->s_bdev) << SECTOR_SHIFT &&
+	    !(sbi->s_features & ZONEFS_F_AGGRCNV)) {
+		zonefs_err(sb,
+			   "zone size %llu doesn't match device's zone sectors %llu\n",
+			   zi->i_zone_size,
+			   bdev_zone_sectors(sb->s_bdev) << SECTOR_SHIFT);
+		return -EINVAL;
+	}
 
 	zi->i_max_size = min_t(loff_t, MAX_LFS_FILESIZE,
 			       zone->capacity << SECTOR_SHIFT);
@@ -1325,6 +1433,22 @@
 	sb->s_maxbytes = max(zi->i_max_size, sb->s_maxbytes);
 	sbi->s_blocks += zi->i_max_size >> sb->s_blocksize_bits;
 	sbi->s_used_blocks += zi->i_wpoffset >> sb->s_blocksize_bits;
+
+	/*
+	 * For sequential zones, make sure that any open zone is closed first
+	 * to ensure that the initial number of open zones is 0, in sync with
+	 * the open zone accounting done when the mount option
+	 * ZONEFS_MNTOPT_EXPLICIT_OPEN is used.
+	 */
+	if (type == ZONEFS_ZTYPE_SEQ &&
+	    (zone->cond == BLK_ZONE_COND_IMP_OPEN ||
+	     zone->cond == BLK_ZONE_COND_EXP_OPEN)) {
+		mutex_lock(&zi->i_truncate_mutex);
+		ret = zonefs_zone_mgmt(inode, REQ_OP_ZONE_CLOSE);
+		mutex_unlock(&zi->i_truncate_mutex);
+	}
+
+	return ret;
 }
 
 static struct dentry *zonefs_create_inode(struct dentry *parent,
@@ -1334,20 +1458,27 @@
 	struct inode *dir = d_inode(parent);
 	struct dentry *dentry;
 	struct inode *inode;
+	int ret = -ENOMEM;
 
 	dentry = d_alloc_name(parent, name);
 	if (!dentry)
-		return NULL;
+		return ERR_PTR(ret);
 
 	inode = new_inode(parent->d_sb);
 	if (!inode)
 		goto dput;
 
 	inode->i_ctime = inode->i_mtime = inode->i_atime = dir->i_ctime;
-	if (zone)
-		zonefs_init_file_inode(inode, zone, type);
-	else
+	if (zone) {
+		ret = zonefs_init_file_inode(inode, zone, type);
+		if (ret) {
+			iput(inode);
+			goto dput;
+		}
+	} else {
 		zonefs_init_dir_inode(dir, inode, type);
+	}
+
 	d_add(dentry, inode);
 	dir->i_size++;
 
@@ -1356,7 +1487,7 @@
 dput:
 	dput(dentry);
 
-	return NULL;
+	return ERR_PTR(ret);
 }
 
 struct zonefs_zone_data {
@@ -1376,7 +1507,7 @@
 	struct blk_zone *zone, *next, *end;
 	const char *zgroup_name;
 	char *file_name;
-	struct dentry *dir;
+	struct dentry *dir, *dent;
 	unsigned int n = 0;
 	int ret;
 
@@ -1394,8 +1525,8 @@
 		zgroup_name = "seq";
 
 	dir = zonefs_create_inode(sb->s_root, zgroup_name, NULL, type);
-	if (!dir) {
-		ret = -ENOMEM;
+	if (IS_ERR(dir)) {
+		ret = PTR_ERR(dir);
 		goto free;
 	}
 
@@ -1441,8 +1572,9 @@
 		 * Use the file number within its group as file name.
 		 */
 		snprintf(file_name, ZONEFS_NAME_MAX - 1, "%u", n);
-		if (!zonefs_create_inode(dir, file_name, zone, type)) {
-			ret = -ENOMEM;
+		dent = zonefs_create_inode(dir, file_name, zone, type);
+		if (IS_ERR(dent)) {
+			ret = PTR_ERR(dent);
 			goto free;
 		}
 
@@ -1658,11 +1790,6 @@
 	sbi->s_mount_opts = ZONEFS_MNTOPT_ERRORS_RO;
 	sbi->s_max_open_zones = bdev_max_open_zones(sb->s_bdev);
 	atomic_set(&sbi->s_open_zones, 0);
-	if (!sbi->s_max_open_zones &&
-	    sbi->s_mount_opts & ZONEFS_MNTOPT_EXPLICIT_OPEN) {
-		zonefs_info(sb, "No open zones limit. Ignoring explicit_open mount option\n");
-		sbi->s_mount_opts &= ~ZONEFS_MNTOPT_EXPLICIT_OPEN;
-	}
 
 	ret = zonefs_read_super(sb);
 	if (ret)
@@ -1681,6 +1808,12 @@
 	zonefs_info(sb, "Mounting %u zones",
 		    blkdev_nr_zones(sb->s_bdev->bd_disk));
 
+	if (!sbi->s_max_open_zones &&
+	    sbi->s_mount_opts & ZONEFS_MNTOPT_EXPLICIT_OPEN) {
+		zonefs_info(sb, "No open zones limit. Ignoring explicit_open mount option\n");
+		sbi->s_mount_opts &= ~ZONEFS_MNTOPT_EXPLICIT_OPEN;
+	}
+
 	/* Create root directory inode */
 	ret = -ENOMEM;
 	inode = new_inode(sb);
@@ -1787,5 +1920,6 @@
 MODULE_AUTHOR("Damien Le Moal");
 MODULE_DESCRIPTION("Zone file system for zoned block devices");
 MODULE_LICENSE("GPL");
+MODULE_ALIAS_FS("zonefs");
 module_init(zonefs_init);
 module_exit(zonefs_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/include/acpi/acpi_bus.h
+++ linux-xilinx-zynqmp-5.15.0/include/acpi/acpi_bus.h
@@ -52,7 +52,7 @@
 bool acpi_check_dsm(acpi_handle handle, const guid_t *guid, u64 rev, u64 funcs);
 union acpi_object *acpi_evaluate_dsm(acpi_handle handle, const guid_t *guid,
 			u64 rev, u64 func, union acpi_object *argv4);
-
+#ifdef CONFIG_ACPI
 static inline union acpi_object *
 acpi_evaluate_dsm_typed(acpi_handle handle, const guid_t *guid, u64 rev,
 			u64 func, union acpi_object *argv4,
@@ -68,6 +68,7 @@
 
 	return obj;
 }
+#endif
 
 #define	ACPI_INIT_DSM_ARGV4(cnt, eles)			\
 	{						\
@@ -613,9 +614,10 @@
 int acpi_disable_wakeup_device_power(struct acpi_device *dev);
 
 #ifdef CONFIG_X86
-bool acpi_device_always_present(struct acpi_device *adev);
+bool acpi_device_override_status(struct acpi_device *adev, unsigned long long *status);
 #else
-static inline bool acpi_device_always_present(struct acpi_device *adev)
+static inline bool acpi_device_override_status(struct acpi_device *adev,
+					       unsigned long long *status)
 {
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/acpi/acpixf.h
+++ linux-xilinx-zynqmp-5.15.0/include/acpi/acpixf.h
@@ -749,6 +749,7 @@
 						     acpi_event_status
 						     *event_status))
 ACPI_HW_DEPENDENT_RETURN_UINT32(u32 acpi_dispatch_gpe(acpi_handle gpe_device, u32 gpe_number))
+ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_hw_disable_all_gpes(void))
 ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_disable_all_gpes(void))
 ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_enable_all_runtime_gpes(void))
 ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_enable_all_wakeup_gpes(void))
--- linux-xilinx-zynqmp-5.15.0.orig/include/acpi/actypes.h
+++ linux-xilinx-zynqmp-5.15.0/include/acpi/actypes.h
@@ -536,8 +536,14 @@
  * Can be used with access_width of struct acpi_generic_address and access_size of
  * struct acpi_resource_generic_register.
  */
-#define ACPI_ACCESS_BIT_WIDTH(size)     (1 << ((size) + 2))
-#define ACPI_ACCESS_BYTE_WIDTH(size)    (1 << ((size) - 1))
+#define ACPI_ACCESS_BIT_SHIFT		2
+#define ACPI_ACCESS_BYTE_SHIFT		-1
+#define ACPI_ACCESS_BIT_MAX		(31 - ACPI_ACCESS_BIT_SHIFT)
+#define ACPI_ACCESS_BYTE_MAX		(31 - ACPI_ACCESS_BYTE_SHIFT)
+#define ACPI_ACCESS_BIT_DEFAULT		(8 - ACPI_ACCESS_BIT_SHIFT)
+#define ACPI_ACCESS_BYTE_DEFAULT	(8 - ACPI_ACCESS_BYTE_SHIFT)
+#define ACPI_ACCESS_BIT_WIDTH(size)	(1 << ((size) + ACPI_ACCESS_BIT_SHIFT))
+#define ACPI_ACCESS_BYTE_WIDTH(size)	(1 << ((size) + ACPI_ACCESS_BYTE_SHIFT))
 
 /*******************************************************************************
  *
--- linux-xilinx-zynqmp-5.15.0.orig/include/acpi/apei.h
+++ linux-xilinx-zynqmp-5.15.0/include/acpi/apei.h
@@ -27,14 +27,16 @@
 extern int erst_disable;
 #ifdef CONFIG_ACPI_APEI_GHES
 extern bool ghes_disable;
+void __init ghes_init(void);
 #else
 #define ghes_disable 1
+static inline void ghes_init(void) { }
 #endif
 
 #ifdef CONFIG_ACPI_APEI
 void __init acpi_hest_init(void);
 #else
-static inline void acpi_hest_init(void) { return; }
+static inline void acpi_hest_init(void) { }
 #endif
 
 typedef int (*apei_hest_func_t)(struct acpi_hest_header *hest_hdr, void *data);
--- linux-xilinx-zynqmp-5.15.0.orig/include/acpi/cppc_acpi.h
+++ linux-xilinx-zynqmp-5.15.0/include/acpi/cppc_acpi.h
@@ -17,7 +17,7 @@
 #include <acpi/pcc.h>
 #include <acpi/processor.h>
 
-/* Support CPPCv2 and CPPCv3  */
+/* CPPCv2 and CPPCv3 support */
 #define CPPC_V2_REV	2
 #define CPPC_V3_REV	3
 #define CPPC_V2_NUM_ENT	21
@@ -64,6 +64,8 @@
 	int cpu_id;
 	int write_cmd_status;
 	int write_cmd_id;
+	/* Lock used for RMW operations in cpc_write() */
+	raw_spinlock_t rmw_lock;
 	struct cpc_register_resource cpc_regs[MAX_CPC_REG_ENT];
 	struct acpi_psd_package domain_info;
 	struct kobject kobj;
@@ -138,6 +140,7 @@
 extern int cppc_get_nominal_perf(int cpunum, u64 *nominal_perf);
 extern int cppc_get_perf_ctrs(int cpu, struct cppc_perf_fb_ctrs *perf_fb_ctrs);
 extern int cppc_set_perf(int cpu, struct cppc_perf_ctrls *perf_ctrls);
+extern int cppc_set_enable(int cpu, bool enable);
 extern int cppc_get_perf_caps(int cpu, struct cppc_perf_caps *caps);
 extern bool acpi_cpc_valid(void);
 extern int acpi_get_psd_map(unsigned int cpu, struct cppc_cpudata *cpu_data);
@@ -162,6 +165,10 @@
 {
 	return -ENOTSUPP;
 }
+static inline int cppc_set_enable(int cpu, bool enable)
+{
+	return -ENOTSUPP;
+}
 static inline int cppc_get_perf_caps(int cpu, struct cppc_perf_caps *caps)
 {
 	return -ENOTSUPP;
--- linux-xilinx-zynqmp-5.15.0.orig/include/acpi/ghes.h
+++ linux-xilinx-zynqmp-5.15.0/include/acpi/ghes.h
@@ -71,7 +71,7 @@
 void ghes_unregister_vendor_record_notifier(struct notifier_block *nb);
 #endif
 
-int ghes_estatus_pool_init(int num_ghes);
+int ghes_estatus_pool_init(unsigned int num_ghes);
 
 /* From drivers/edac/ghes_edac.c */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/bitops/atomic.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/bitops/atomic.h
@@ -39,9 +39,6 @@
 	unsigned long mask = BIT_MASK(nr);
 
 	p += BIT_WORD(nr);
-	if (READ_ONCE(*p) & mask)
-		return 1;
-
 	old = arch_atomic_long_fetch_or(mask, (atomic_long_t *)p);
 	return !!(old & mask);
 }
@@ -53,9 +50,6 @@
 	unsigned long mask = BIT_MASK(nr);
 
 	p += BIT_WORD(nr);
-	if (!(READ_ONCE(*p) & mask))
-		return 0;
-
 	old = arch_atomic_long_fetch_andnot(mask, (atomic_long_t *)p);
 	return !!(old & mask);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/bitops/find.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/bitops/find.h
@@ -97,6 +97,7 @@
 
 #ifdef CONFIG_GENERIC_FIND_FIRST_BIT
 
+#ifndef find_first_bit
 /**
  * find_first_bit - find the first set bit in a memory region
  * @addr: The address to start the search at
@@ -116,7 +117,9 @@
 
 	return _find_first_bit(addr, size);
 }
+#endif
 
+#ifndef find_first_zero_bit
 /**
  * find_first_zero_bit - find the first cleared bit in a memory region
  * @addr: The address to start the search at
@@ -136,6 +139,8 @@
 
 	return _find_first_zero_bit(addr, size);
 }
+#endif
+
 #else /* CONFIG_GENERIC_FIND_FIRST_BIT */
 
 #ifndef find_first_bit
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/io.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/io.h
@@ -190,7 +190,7 @@
 	u64 val;
 
 	__io_br();
-	val = __le64_to_cpu(__raw_readq(addr));
+	val = __le64_to_cpu((__le64 __force)__raw_readq(addr));
 	__io_ar(val);
 	return val;
 }
@@ -233,7 +233,7 @@
 static inline void writeq(u64 value, volatile void __iomem *addr)
 {
 	__io_bw();
-	__raw_writeq(__cpu_to_le64(value), addr);
+	__raw_writeq((u64 __force)__cpu_to_le64(value), addr);
 	__io_aw();
 }
 #endif
@@ -1125,9 +1125,7 @@
 }
 #endif
 
-#ifndef CONFIG_GENERIC_DEVMEM_IS_ALLOWED
 extern int devmem_is_allowed(unsigned long pfn);
-#endif
 
 #endif /* __KERNEL__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/numa.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/numa.h
@@ -35,6 +35,7 @@
 void __init numa_set_distance(int from, int to, int distance);
 void __init numa_free_distance(void);
 void __init early_map_cpu_to_node(unsigned int cpu, int nid);
+int __init early_cpu_to_node(int cpu);
 void numa_store_cpu_info(unsigned int cpu);
 void numa_add_cpu(unsigned int cpu);
 void numa_remove_cpu(unsigned int cpu);
@@ -46,6 +47,7 @@
 static inline void numa_remove_cpu(unsigned int cpu) { }
 static inline void arch_numa_init(void) { }
 static inline void early_map_cpu_to_node(unsigned int cpu, int nid) { }
+static inline int early_cpu_to_node(int cpu) { return 0; }
 
 #endif	/* CONFIG_NUMA */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/qspinlock.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/qspinlock.h
@@ -41,7 +41,7 @@
  */
 static __always_inline int queued_spin_value_unlocked(struct qspinlock lock)
 {
-	return !atomic_read(&lock.val);
+	return !lock.val.counter;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/sections.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/sections.h
@@ -114,7 +114,7 @@
 /**
  * memory_intersects - checks if the region occupied by an object intersects
  *                     with another memory region
- * @begin: virtual address of the beginning of the memory regien
+ * @begin: virtual address of the beginning of the memory region
  * @end: virtual address of the end of the memory region
  * @virt: virtual address of the memory object
  * @size: size of the memory object
@@ -127,7 +127,10 @@
 {
 	void *vend = virt + size;
 
-	return (virt >= begin && virt < end) || (vend >= begin && vend < end);
+	if (virt < end && vend > begin)
+		return true;
+
+	return false;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/tlb.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/tlb.h
@@ -207,12 +207,16 @@
 #define tlb_needs_table_invalidate() (true)
 #endif
 
+void tlb_remove_table_sync_one(void);
+
 #else
 
 #ifdef tlb_needs_table_invalidate
 #error tlb_needs_table_invalidate() requires MMU_GATHER_RCU_TABLE_FREE
 #endif
 
+static inline void tlb_remove_table_sync_one(void) { }
+
 #endif /* CONFIG_MMU_GATHER_RCU_TABLE_FREE */
 
 
@@ -565,10 +569,14 @@
 #define tlb_remove_huge_tlb_entry(h, tlb, ptep, address)	\
 	do {							\
 		unsigned long _sz = huge_page_size(h);		\
-		if (_sz == PMD_SIZE)				\
-			tlb_flush_pmd_range(tlb, address, _sz);	\
-		else if (_sz == PUD_SIZE)			\
+		if (_sz >= P4D_SIZE)				\
+			tlb_flush_p4d_range(tlb, address, _sz);	\
+		else if (_sz >= PUD_SIZE)			\
 			tlb_flush_pud_range(tlb, address, _sz);	\
+		else if (_sz >= PMD_SIZE)			\
+			tlb_flush_pmd_range(tlb, address, _sz);	\
+		else						\
+			tlb_flush_pte_range(tlb, address, _sz);	\
 		__tlb_remove_tlb_entry(tlb, ptep, address);	\
 	} while (0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/vmlinux.lds.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/vmlinux.lds.h
@@ -81,8 +81,8 @@
 #define RO_EXCEPTION_TABLE
 #endif
 
-/* Align . to a 8 byte boundary equals to maximum function alignment. */
-#define ALIGN_FUNCTION()  . = ALIGN(8)
+/* Align . function alignment. */
+#define ALIGN_FUNCTION()  . = ALIGN(CONFIG_FUNCTION_ALIGNMENT)
 
 /*
  * LD_DEAD_CODE_DATA_ELIMINATION option enables -fdata-sections, which
@@ -101,7 +101,7 @@
 #define DATA_MAIN .data .data.[0-9a-zA-Z_]* .data..L* .data..compoundliteral* .data.$__unnamed_* .data.$L*
 #define SDATA_MAIN .sdata .sdata.[0-9a-zA-Z_]*
 #define RODATA_MAIN .rodata .rodata.[0-9a-zA-Z_]* .rodata..L*
-#define BSS_MAIN .bss .bss.[0-9a-zA-Z_]* .bss..compoundliteral*
+#define BSS_MAIN .bss .bss.[0-9a-zA-Z_]* .bss..L* .bss..compoundliteral*
 #define SBSS_MAIN .sbss .sbss.[0-9a-zA-Z_]*
 #else
 #define TEXT_MAIN .text
@@ -337,6 +337,7 @@
 #define DATA_DATA							\
 	*(.xiptext)							\
 	*(DATA_MAIN)							\
+	*(.data..decrypted)						\
 	*(.ref.data)							\
 	*(.data..shared_aligned) /* percpu related */			\
 	MEM_KEEP(init.data*)						\
@@ -428,7 +429,7 @@
 	. = ALIGN((align));						\
 	.rodata           : AT(ADDR(.rodata) - LOAD_OFFSET) {		\
 		__start_rodata = .;					\
-		*(.rodata) *(.rodata.*)					\
+		*(.rodata) *(.rodata.*) *(.data.rel.ro*)		\
 		SCHED_DATA						\
 		RO_AFTER_INIT_DATA	/* Read only after init */	\
 		. = ALIGN(8);						\
@@ -549,10 +550,9 @@
  */
 #ifdef CONFIG_CFI_CLANG
 #define TEXT_CFI_JT							\
-		. = ALIGN(PMD_SIZE);					\
+		ALIGN_FUNCTION();					\
 		__cfi_jt_start = .;					\
 		*(.text..L.cfi.jumptable .text..L.cfi.jumptable.*)	\
-		. = ALIGN(PMD_SIZE);					\
 		__cfi_jt_end = .;
 #else
 #define TEXT_CFI_JT
@@ -903,7 +903,12 @@
 #define PRINTK_INDEX
 #endif
 
+/*
+ * Discard .note.GNU-stack, which is emitted as PROGBITS by the compiler.
+ * Otherwise, the type of .notes section would become PROGBITS instead of NOTES.
+ */
 #define NOTES								\
+	/DISCARD/ : { *(.note.GNU-stack) }				\
 	.notes : AT(ADDR(.notes) - LOAD_OFFSET) {			\
 		__start_notes = .;					\
 		KEEP(*(.note.*))					\
@@ -970,7 +975,6 @@
 #ifdef CONFIG_AMD_MEM_ENCRYPT
 #define PERCPU_DECRYPTED_SECTION					\
 	. = ALIGN(PAGE_SIZE);						\
-	*(.data..decrypted)						\
 	*(.data..percpu..decrypted)					\
 	. = ALIGN(PAGE_SIZE);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/include/asm-generic/word-at-a-time.h
+++ linux-xilinx-zynqmp-5.15.0/include/asm-generic/word-at-a-time.h
@@ -38,7 +38,7 @@
 	return (mask >> 8) ? byte : byte + 1;
 }
 
-static inline bool has_zero(unsigned long val, unsigned long *data, const struct word_at_a_time *c)
+static inline unsigned long has_zero(unsigned long val, unsigned long *data, const struct word_at_a_time *c)
 {
 	unsigned long rhs = val | c->low_bits;
 	*data = rhs;
--- linux-xilinx-zynqmp-5.15.0.orig/include/clocksource/arm_arch_timer.h
+++ linux-xilinx-zynqmp-5.15.0/include/clocksource/arm_arch_timer.h
@@ -24,7 +24,7 @@
 
 enum arch_timer_reg {
 	ARCH_TIMER_REG_CTRL,
-	ARCH_TIMER_REG_TVAL,
+	ARCH_TIMER_REG_CVAL,
 };
 
 enum arch_timer_ppi_nr {
--- linux-xilinx-zynqmp-5.15.0.orig/include/clocksource/hyperv_timer.h
+++ linux-xilinx-zynqmp-5.15.0/include/clocksource/hyperv_timer.h
@@ -34,6 +34,8 @@
 
 extern struct ms_hyperv_tsc_page *hv_get_tsc_page(void);
 
+extern void hv_adj_sched_clock_offset(u64 offset);
+
 static inline notrace u64
 hv_read_tsc_page_tsc(const struct ms_hyperv_tsc_page *tsc_pg, u64 *cur_tsc)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/algapi.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/algapi.h
@@ -10,6 +10,7 @@
 #include <linux/crypto.h>
 #include <linux/list.h>
 #include <linux/kernel.h>
+#include <linux/workqueue.h>
 
 /*
  * Maximum values for blocksize and alignmask, used to allocate
@@ -55,6 +56,8 @@
 		struct crypto_spawn *spawns;
 	};
 
+	struct work_struct free_work;
+
 	void *__ctx[] CRYPTO_MINALIGN_ATTR;
 };
 
@@ -256,4 +259,11 @@
 	CRYPTO_MSG_ALG_LOADED,
 };
 
+static inline void crypto_request_complete(struct crypto_async_request *req,
+					   int err)
+{
+	crypto_completion_t complete = req->complete;
+	complete(req, err);
+}
+
 #endif	/* _CRYPTO_ALGAPI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/blake2s.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/blake2s.h
@@ -101,7 +101,4 @@
 	blake2s_final(&state, out);
 }
 
-void blake2s256_hmac(u8 *out, const u8 *in, const u8 *key, const size_t inlen,
-		     const size_t keylen);
-
 #endif /* _CRYPTO_BLAKE2S_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/chacha.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/chacha.h
@@ -47,12 +47,19 @@
 		hchacha_block_generic(state, out, nrounds);
 }
 
+enum chacha_constants { /* expand 32-byte k */
+	CHACHA_CONSTANT_EXPA = 0x61707865U,
+	CHACHA_CONSTANT_ND_3 = 0x3320646eU,
+	CHACHA_CONSTANT_2_BY = 0x79622d32U,
+	CHACHA_CONSTANT_TE_K = 0x6b206574U
+};
+
 static inline void chacha_init_consts(u32 *state)
 {
-	state[0]  = 0x61707865; /* "expa" */
-	state[1]  = 0x3320646e; /* "nd 3" */
-	state[2]  = 0x79622d32; /* "2-by" */
-	state[3]  = 0x6b206574; /* "te k" */
+	state[0]  = CHACHA_CONSTANT_EXPA;
+	state[1]  = CHACHA_CONSTANT_ND_3;
+	state[2]  = CHACHA_CONSTANT_2_BY;
+	state[3]  = CHACHA_CONSTANT_TE_K;
 }
 
 void chacha_init_arch(u32 *state, const u32 *key, const u8 *iv);
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/drbg.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/drbg.h
@@ -105,6 +105,12 @@
 	struct drbg_string *testentropy; /* TEST PARAMETER: test entropy */
 };
 
+enum drbg_seed_state {
+	DRBG_SEED_STATE_UNSEEDED,
+	DRBG_SEED_STATE_PARTIAL, /* Seeded with !rng_is_initialized() */
+	DRBG_SEED_STATE_FULL,
+};
+
 struct drbg_state {
 	struct mutex drbg_mutex;	/* lock around DRBG */
 	unsigned char *V;	/* internal state 10.1.1.1 1a) */
@@ -127,16 +133,14 @@
 	struct crypto_wait ctr_wait;		/* CTR mode async wait obj */
 	struct scatterlist sg_in, sg_out;	/* CTR mode SGLs */
 
-	bool seeded;		/* DRBG fully seeded? */
+	enum drbg_seed_state seeded;		/* DRBG fully seeded? */
 	bool pr;		/* Prediction resistance enabled? */
 	bool fips_primed;	/* Continuous test primed? */
 	unsigned char *prev;	/* FIPS 140-2 continuous test value */
-	struct work_struct seed_work;	/* asynchronous seeding support */
 	struct crypto_rng *jent;
 	const struct drbg_state_ops *d_ops;
 	const struct drbg_core *core;
 	struct drbg_string test_data;
-	struct random_ready_callback random_ready;
 };
 
 static inline __u8 drbg_statelen(struct drbg_state *drbg)
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/if_alg.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/if_alg.h
@@ -138,6 +138,7 @@
  *			recvmsg is invoked.
  * @init:		True if metadata has been sent.
  * @len:		Length of memory allocated for this data structure.
+ * @inflight:		Non-zero when AIO requests are in flight.
  */
 struct af_alg_ctx {
 	struct list_head tsgl_list;
@@ -156,6 +157,8 @@
 	bool init;
 
 	unsigned int len;
+
+	unsigned int inflight;
 };
 
 int af_alg_register_type(const struct af_alg_type *type);
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/internal/blake2s.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/internal/blake2s.h
@@ -8,112 +8,14 @@
 #define _CRYPTO_INTERNAL_BLAKE2S_H
 
 #include <crypto/blake2s.h>
-#include <crypto/internal/hash.h>
 #include <linux/string.h>
 
-void blake2s_compress_generic(struct blake2s_state *state,const u8 *block,
+void blake2s_compress_generic(struct blake2s_state *state, const u8 *block,
 			      size_t nblocks, const u32 inc);
 
-void blake2s_compress_arch(struct blake2s_state *state,const u8 *block,
-			   size_t nblocks, const u32 inc);
+void blake2s_compress(struct blake2s_state *state, const u8 *block,
+		      size_t nblocks, const u32 inc);
 
 bool blake2s_selftest(void);
 
-static inline void blake2s_set_lastblock(struct blake2s_state *state)
-{
-	state->f[0] = -1;
-}
-
-typedef void (*blake2s_compress_t)(struct blake2s_state *state,
-				   const u8 *block, size_t nblocks, u32 inc);
-
-/* Helper functions for BLAKE2s shared by the library and shash APIs */
-
-static inline void __blake2s_update(struct blake2s_state *state,
-				    const u8 *in, size_t inlen,
-				    blake2s_compress_t compress)
-{
-	const size_t fill = BLAKE2S_BLOCK_SIZE - state->buflen;
-
-	if (unlikely(!inlen))
-		return;
-	if (inlen > fill) {
-		memcpy(state->buf + state->buflen, in, fill);
-		(*compress)(state, state->buf, 1, BLAKE2S_BLOCK_SIZE);
-		state->buflen = 0;
-		in += fill;
-		inlen -= fill;
-	}
-	if (inlen > BLAKE2S_BLOCK_SIZE) {
-		const size_t nblocks = DIV_ROUND_UP(inlen, BLAKE2S_BLOCK_SIZE);
-		/* Hash one less (full) block than strictly possible */
-		(*compress)(state, in, nblocks - 1, BLAKE2S_BLOCK_SIZE);
-		in += BLAKE2S_BLOCK_SIZE * (nblocks - 1);
-		inlen -= BLAKE2S_BLOCK_SIZE * (nblocks - 1);
-	}
-	memcpy(state->buf + state->buflen, in, inlen);
-	state->buflen += inlen;
-}
-
-static inline void __blake2s_final(struct blake2s_state *state, u8 *out,
-				   blake2s_compress_t compress)
-{
-	blake2s_set_lastblock(state);
-	memset(state->buf + state->buflen, 0,
-	       BLAKE2S_BLOCK_SIZE - state->buflen); /* Padding */
-	(*compress)(state, state->buf, 1, state->buflen);
-	cpu_to_le32_array(state->h, ARRAY_SIZE(state->h));
-	memcpy(out, state->h, state->outlen);
-}
-
-/* Helper functions for shash implementations of BLAKE2s */
-
-struct blake2s_tfm_ctx {
-	u8 key[BLAKE2S_KEY_SIZE];
-	unsigned int keylen;
-};
-
-static inline int crypto_blake2s_setkey(struct crypto_shash *tfm,
-					const u8 *key, unsigned int keylen)
-{
-	struct blake2s_tfm_ctx *tctx = crypto_shash_ctx(tfm);
-
-	if (keylen == 0 || keylen > BLAKE2S_KEY_SIZE)
-		return -EINVAL;
-
-	memcpy(tctx->key, key, keylen);
-	tctx->keylen = keylen;
-
-	return 0;
-}
-
-static inline int crypto_blake2s_init(struct shash_desc *desc)
-{
-	const struct blake2s_tfm_ctx *tctx = crypto_shash_ctx(desc->tfm);
-	struct blake2s_state *state = shash_desc_ctx(desc);
-	unsigned int outlen = crypto_shash_digestsize(desc->tfm);
-
-	__blake2s_init(state, outlen, tctx->key, tctx->keylen);
-	return 0;
-}
-
-static inline int crypto_blake2s_update(struct shash_desc *desc,
-					const u8 *in, unsigned int inlen,
-					blake2s_compress_t compress)
-{
-	struct blake2s_state *state = shash_desc_ctx(desc);
-
-	__blake2s_update(state, in, inlen, compress);
-	return 0;
-}
-
-static inline int crypto_blake2s_final(struct shash_desc *desc, u8 *out,
-				       blake2s_compress_t compress)
-{
-	struct blake2s_state *state = shash_desc_ctx(desc);
-
-	__blake2s_final(state, out, compress);
-	return 0;
-}
-
 #endif /* _CRYPTO_INTERNAL_BLAKE2S_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/crypto/internal/kpp.h
+++ linux-xilinx-zynqmp-5.15.0/include/crypto/internal/kpp.h
@@ -18,6 +18,12 @@
 	return req->__ctx;
 }
 
+static inline void kpp_set_reqsize(struct crypto_kpp *kpp,
+				   unsigned int reqsize)
+{
+	crypto_kpp_alg(kpp)->reqsize = reqsize;
+}
+
 static inline void *kpp_tfm_ctx(struct crypto_kpp *tfm)
 {
 	return tfm->base.__crt_ctx;
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_bridge.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_bridge.h
@@ -191,7 +191,7 @@
 	 * or &drm_encoder_helper_funcs.dpms hook.
 	 *
 	 * The bridge must assume that the display pipe (i.e. clocks and timing
-	 * singals) feeding it is no longer running when this callback is
+	 * signals) feeding it is no longer running when this callback is
 	 * called.
 	 *
 	 * The @post_disable callback is optional.
@@ -447,11 +447,11 @@
 	 *
 	 * The returned array must be allocated with kmalloc() and will be
 	 * freed by the caller. If the allocation fails, NULL should be
-	 * returned. num_output_fmts must be set to the returned array size.
+	 * returned. num_input_fmts must be set to the returned array size.
 	 * Formats listed in the returned array should be listed in decreasing
 	 * preference order (the core will try all formats until it finds one
 	 * that works). When the format is not supported NULL should be
-	 * returned and num_output_fmts should be set to 0.
+	 * returned and num_input_fmts should be set to 0.
 	 *
 	 * This method is called on all elements of the bridge chain as part of
 	 * the bus format negotiation process that happens in
@@ -914,4 +914,17 @@
 struct drm_connector *drm_panel_bridge_connector(struct drm_bridge *bridge);
 #endif
 
+#if defined(CONFIG_OF) && defined(CONFIG_DRM_PANEL_BRIDGE)
+struct drm_bridge *devm_drm_of_get_bridge(struct device *dev, struct device_node *node,
+					  u32 port, u32 endpoint);
+#else
+static inline struct drm_bridge *devm_drm_of_get_bridge(struct device *dev,
+							struct device_node *node,
+							u32 port,
+							u32 endpoint)
+{
+	return ERR_PTR(-ENODEV);
+}
+#endif
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_color_mgmt.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_color_mgmt.h
@@ -24,6 +24,7 @@
 #define __DRM_COLOR_MGMT_H__
 
 #include <linux/ctype.h>
+#include <linux/math64.h>
 #include <drm/drm_property.h>
 
 struct drm_crtc;
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_connector.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_connector.h
@@ -304,6 +304,22 @@
 };
 
 /**
+ * struct drm_luminance_range_info - Panel's luminance range for
+ * &drm_display_info. Calculated using data in EDID
+ *
+ * This struct is used to store a luminance range supported by panel
+ * as calculated using data from EDID's static hdr metadata.
+ *
+ * @min_luminance: This is the min supported luminance value
+ *
+ * @max_luminance: This is the max supported luminance value
+ */
+struct drm_luminance_range_info {
+	u32 min_luminance;
+	u32 max_luminance;
+};
+
+/**
  * struct drm_monitor_range_info - Panel's Monitor range in EDID for
  * &drm_display_info
  *
@@ -566,10 +582,16 @@
 	bool rgb_quant_range_selectable;
 
 	/**
-	 * @edid_hdmi_dc_modes: Mask of supported hdmi deep color modes. Even
-	 * more stuff redundant with @bus_formats.
+	 * @edid_hdmi_rgb444_dc_modes: Mask of supported hdmi deep color modes
+	 * in RGB 4:4:4. Even more stuff redundant with @bus_formats.
 	 */
-	u8 edid_hdmi_dc_modes;
+	u8 edid_hdmi_rgb444_dc_modes;
+
+	/**
+	 * @edid_hdmi_ycbcr444_dc_modes: Mask of supported hdmi deep color
+	 * modes in YCbCr 4:4:4. Even more stuff redundant with @bus_formats.
+	 */
+	u8 edid_hdmi_ycbcr444_dc_modes;
 
 	/**
 	 * @cea_rev: CEA revision of the HDMI sink.
@@ -590,6 +612,11 @@
 	 * @monitor_range: Frequency range supported by monitor range descriptor
 	 */
 	struct drm_monitor_range_info monitor_range;
+
+	/**
+	 * @luminance_range: Luminance range supported by panel
+	 */
+	struct drm_luminance_range_info luminance_range;
 };
 
 int drm_display_info_set_bus_formats(struct drm_display_info *info,
@@ -786,6 +813,13 @@
 	 * DRM blob property for HDR output metadata
 	 */
 	struct drm_property_blob *hdr_output_metadata;
+
+	/**
+	 * @gen_hdr_output_metadata:
+	 * DRM blob property for Generic HDR output metadata
+	 */
+	struct drm_property_blob *gen_hdr_output_metadata;
+
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_dp_helper.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_dp_helper.h
@@ -455,7 +455,7 @@
 # define DP_FEC_BIT_ERROR_COUNT_CAP	    (1 << 3)
 
 /* DP-HDMI2.1 PCON DSC ENCODER SUPPORT */
-#define DP_PCON_DSC_ENCODER_CAP_SIZE        0xC	/* 0x9E - 0x92 */
+#define DP_PCON_DSC_ENCODER_CAP_SIZE        0xD	/* 0x92 through 0x9E */
 #define DP_PCON_DSC_ENCODER                 0x092
 # define DP_PCON_DSC_ENCODER_SUPPORTED      (1 << 0)
 # define DP_PCON_DSC_PPS_ENC_OVERRIDE       (1 << 1)
@@ -1090,6 +1090,7 @@
 
 /* Extended Receiver Capability: See DP_DPCD_REV for definitions */
 #define DP_DP13_DPCD_REV                    0x2200
+#define DP_DP13_MAX_LINK_RATE               0x2201
 
 #define DP_DPRX_FEATURE_ENUMERATION_LIST    0x2210  /* DP 1.3 */
 # define DP_GTC_CAP					(1 << 0)  /* DP 1.3 */
@@ -1495,7 +1496,7 @@
 
 #define DP_BRANCH_OUI_HEADER_SIZE	0xc
 #define DP_RECEIVER_CAP_SIZE		0xf
-#define DP_DSC_RECEIVER_CAP_SIZE        0xf
+#define DP_DSC_RECEIVER_CAP_SIZE        0x10 /* DSC Capabilities 0x60 through 0x6F */
 #define EDP_PSR_RECEIVER_CAP_SIZE	2
 #define EDP_DISPLAY_CTL_CAP_SIZE	3
 #define DP_LTTPR_COMMON_CAP_SIZE	8
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_dp_mst_helper.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_dp_mst_helper.h
@@ -232,6 +232,13 @@
 	 */
 	struct list_head destroy_next;
 
+	/**
+	 * @rad: Relative Address of the MST branch.
+	 * For &drm_dp_mst_topology_mgr.mst_primary, it's rad[8] are all 0,
+	 * unset and unused. For MST branches connected after mst_primary,
+	 * in each element of rad[] the nibbles are ordered by the most
+	 * signifcant 4 bits first and the least significant 4 bits second.
+	 */
 	u8 rad[8];
 	u8 lct;
 	int num_ports;
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_edid.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_edid.h
@@ -121,7 +121,7 @@
 			u8 supported_scalings;
 			u8 preferred_refresh;
 		} __attribute__((packed)) cvt;
-	} formula;
+	} __attribute__((packed)) formula;
 } __attribute__((packed));
 
 struct detailed_data_wpindex {
@@ -154,7 +154,7 @@
 		struct detailed_data_wpindex color;
 		struct std_timing timings[6];
 		struct cvt_timing cvt[4];
-	} data;
+	} __attribute__((packed)) data;
 } __attribute__((packed));
 
 #define EDID_DETAIL_EST_TIMINGS 0xf7
@@ -172,7 +172,7 @@
 	union {
 		struct detailed_pixel_timing pixel_data;
 		struct detailed_non_pixel other_data;
-	} data;
+	} __attribute__((packed)) data;
 } __attribute__((packed));
 
 #define DRM_EDID_INPUT_SERRATION_VSYNC (1 << 0)
@@ -418,6 +418,10 @@
 drm_hdmi_infoframe_set_hdr_metadata(struct hdmi_drm_infoframe *frame,
 				    const struct drm_connector_state *conn_state);
 
+int
+drm_hdmi_infoframe_set_gen_hdr_metadata(struct hdmi_drm_infoframe *frame,
+					const struct drm_connector_state *conn_state);
+
 /**
  * drm_eld_mnl - Get ELD monitor name length in bytes.
  * @eld: pointer to an eld memory structure with mnl set
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_fb_helper.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_fb_helper.h
@@ -229,8 +229,7 @@
 			     struct drm_fb_helper *fb_helper,
 			     struct drm_fb_helper_surface_size *sizes);
 
-void drm_fb_helper_deferred_io(struct fb_info *info,
-			       struct list_head *pagelist);
+void drm_fb_helper_deferred_io(struct fb_info *info, struct list_head *pagereflist);
 
 ssize_t drm_fb_helper_sys_read(struct fb_info *info, char __user *buf,
 			       size_t count, loff_t *ppos);
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_fixed.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_fixed.h
@@ -88,7 +88,7 @@
 
 static inline int drm_fixp2int_ceil(s64 a)
 {
-	if (a > 0)
+	if (a >= 0)
 		return drm_fixp2int(a + DRM_FIXED_ALMOST_ONE);
 	else
 		return drm_fixp2int(a - DRM_FIXED_ALMOST_ONE);
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_fourcc.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_fourcc.h
@@ -128,6 +128,25 @@
 	 */
 	u8 block_h[DRM_FORMAT_MAX_PLANES];
 
+	/**
+	 * @pixels_per_macropixel:
+	 * Number of pixels per macro-pixel (per plane). A macro-pixel is
+	 * composed of multiple pixels, and there can be extra bits between
+	 * pixels. This must be used along with @bytes_per_macropixel, only
+	 * when single pixel size is not byte-aligned. In this case, @cpp
+	 * is not valid and should be 0.
+	 */
+	u8 pixels_per_macropixel[3];
+
+	/**
+	 * @bytes_per_macropixel:
+	 * Number of bytes per macro-pixel (per plane). A macro-pixel is
+	 * composed of multiple pixels. The size of single macro-pixel should
+	 * be byte-aligned. This should be used with @pixels_per_macropixel,
+	 * and @cpp should be 0.
+	 */
+	u8 bytes_per_macropixel[3];
+
 	/** @hsub: Horizontal chroma subsampling factor */
 	u8 hsub;
 	/** @vsub: Vertical chroma subsampling factor */
@@ -315,5 +334,7 @@
 					  int plane);
 uint64_t drm_format_info_min_pitch(const struct drm_format_info *info,
 				   int plane, unsigned int buffer_width);
+uint64_t drm_format_plane_width_bytes(const struct drm_format_info *info,
+				 int plane, unsigned int width);
 
 #endif /* __DRM_FOURCC_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_gem_shmem_helper.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_gem_shmem_helper.h
@@ -107,16 +107,17 @@
 	container_of(obj, struct drm_gem_shmem_object, base)
 
 struct drm_gem_shmem_object *drm_gem_shmem_create(struct drm_device *dev, size_t size);
-void drm_gem_shmem_free_object(struct drm_gem_object *obj);
+void drm_gem_shmem_free(struct drm_gem_shmem_object *shmem);
 
 int drm_gem_shmem_get_pages(struct drm_gem_shmem_object *shmem);
 void drm_gem_shmem_put_pages(struct drm_gem_shmem_object *shmem);
-int drm_gem_shmem_pin(struct drm_gem_object *obj);
-void drm_gem_shmem_unpin(struct drm_gem_object *obj);
-int drm_gem_shmem_vmap(struct drm_gem_object *obj, struct dma_buf_map *map);
-void drm_gem_shmem_vunmap(struct drm_gem_object *obj, struct dma_buf_map *map);
+int drm_gem_shmem_pin(struct drm_gem_shmem_object *shmem);
+void drm_gem_shmem_unpin(struct drm_gem_shmem_object *shmem);
+int drm_gem_shmem_vmap(struct drm_gem_shmem_object *shmem, struct dma_buf_map *map);
+void drm_gem_shmem_vunmap(struct drm_gem_shmem_object *shmem, struct dma_buf_map *map);
+int drm_gem_shmem_mmap(struct drm_gem_shmem_object *shmem, struct vm_area_struct *vma);
 
-int drm_gem_shmem_madvise(struct drm_gem_object *obj, int madv);
+int drm_gem_shmem_madvise(struct drm_gem_shmem_object *shmem, int madv);
 
 static inline bool drm_gem_shmem_is_purgeable(struct drm_gem_shmem_object *shmem)
 {
@@ -125,29 +126,156 @@
 		!shmem->base.dma_buf && !shmem->base.import_attach;
 }
 
-void drm_gem_shmem_purge_locked(struct drm_gem_object *obj);
-bool drm_gem_shmem_purge(struct drm_gem_object *obj);
+void drm_gem_shmem_purge_locked(struct drm_gem_shmem_object *shmem);
+bool drm_gem_shmem_purge(struct drm_gem_shmem_object *shmem);
 
-struct drm_gem_shmem_object *
-drm_gem_shmem_create_with_handle(struct drm_file *file_priv,
-				 struct drm_device *dev, size_t size,
-				 uint32_t *handle);
+struct sg_table *drm_gem_shmem_get_sg_table(struct drm_gem_shmem_object *shmem);
+struct sg_table *drm_gem_shmem_get_pages_sgt(struct drm_gem_shmem_object *shmem);
 
-int drm_gem_shmem_dumb_create(struct drm_file *file, struct drm_device *dev,
-			      struct drm_mode_create_dumb *args);
+void drm_gem_shmem_print_info(const struct drm_gem_shmem_object *shmem,
+			      struct drm_printer *p, unsigned int indent);
+
+/*
+ * GEM object functions
+ */
+
+/**
+ * drm_gem_shmem_object_free - GEM object function for drm_gem_shmem_free()
+ * @obj: GEM object to free
+ *
+ * This function wraps drm_gem_shmem_free(). Drivers that employ the shmem helpers
+ * should use it as their &drm_gem_object_funcs.free handler.
+ */
+static inline void drm_gem_shmem_object_free(struct drm_gem_object *obj)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+
+	drm_gem_shmem_free(shmem);
+}
+
+/**
+ * drm_gem_shmem_object_print_info() - Print &drm_gem_shmem_object info for debugfs
+ * @p: DRM printer
+ * @indent: Tab indentation level
+ * @obj: GEM object
+ *
+ * This function wraps drm_gem_shmem_print_info(). Drivers that employ the shmem helpers should
+ * use this function as their &drm_gem_object_funcs.print_info handler.
+ */
+static inline void drm_gem_shmem_object_print_info(struct drm_printer *p, unsigned int indent,
+						   const struct drm_gem_object *obj)
+{
+	const struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
 
-int drm_gem_shmem_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma);
+	drm_gem_shmem_print_info(shmem, p, indent);
+}
+
+/**
+ * drm_gem_shmem_object_pin - GEM object function for drm_gem_shmem_pin()
+ * @obj: GEM object
+ *
+ * This function wraps drm_gem_shmem_pin(). Drivers that employ the shmem helpers should
+ * use it as their &drm_gem_object_funcs.pin handler.
+ */
+static inline int drm_gem_shmem_object_pin(struct drm_gem_object *obj)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
 
-void drm_gem_shmem_print_info(struct drm_printer *p, unsigned int indent,
-			      const struct drm_gem_object *obj);
+	return drm_gem_shmem_pin(shmem);
+}
+
+/**
+ * drm_gem_shmem_object_unpin - GEM object function for drm_gem_shmem_unpin()
+ * @obj: GEM object
+ *
+ * This function wraps drm_gem_shmem_unpin(). Drivers that employ the shmem helpers should
+ * use it as their &drm_gem_object_funcs.unpin handler.
+ */
+static inline void drm_gem_shmem_object_unpin(struct drm_gem_object *obj)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+
+	drm_gem_shmem_unpin(shmem);
+}
+
+/**
+ * drm_gem_shmem_object_get_sg_table - GEM object function for drm_gem_shmem_get_sg_table()
+ * @obj: GEM object
+ *
+ * This function wraps drm_gem_shmem_get_sg_table(). Drivers that employ the shmem helpers should
+ * use it as their &drm_gem_object_funcs.get_sg_table handler.
+ *
+ * Returns:
+ * A pointer to the scatter/gather table of pinned pages or NULL on failure.
+ */
+static inline struct sg_table *drm_gem_shmem_object_get_sg_table(struct drm_gem_object *obj)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+
+	return drm_gem_shmem_get_sg_table(shmem);
+}
+
+/*
+ * drm_gem_shmem_object_vmap - GEM object function for drm_gem_shmem_vmap()
+ * @obj: GEM object
+ * @map: Returns the kernel virtual address of the SHMEM GEM object's backing store.
+ *
+ * This function wraps drm_gem_shmem_vmap(). Drivers that employ the shmem helpers should
+ * use it as their &drm_gem_object_funcs.vmap handler.
+ *
+ * Returns:
+ * 0 on success or a negative error code on failure.
+ */
+static inline int drm_gem_shmem_object_vmap(struct drm_gem_object *obj, struct dma_buf_map *map)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+
+	return drm_gem_shmem_vmap(shmem, map);
+}
+
+/*
+ * drm_gem_shmem_object_vunmap - GEM object function for drm_gem_shmem_vunmap()
+ * @obj: GEM object
+ * @map: Kernel virtual address where the SHMEM GEM object was mapped
+ *
+ * This function wraps drm_gem_shmem_vunmap(). Drivers that employ the shmem helpers should
+ * use it as their &drm_gem_object_funcs.vunmap handler.
+ */
+static inline void drm_gem_shmem_object_vunmap(struct drm_gem_object *obj, struct dma_buf_map *map)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+
+	drm_gem_shmem_vunmap(shmem, map);
+}
+
+/**
+ * drm_gem_shmem_object_mmap - GEM object function for drm_gem_shmem_mmap()
+ * @obj: GEM object
+ * @vma: VMA for the area to be mapped
+ *
+ * This function wraps drm_gem_shmem_mmap(). Drivers that employ the shmem helpers should
+ * use it as their &drm_gem_object_funcs.mmap handler.
+ *
+ * Returns:
+ * 0 on success or a negative error code on failure.
+ */
+static inline int drm_gem_shmem_object_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
+{
+	struct drm_gem_shmem_object *shmem = to_drm_gem_shmem_obj(obj);
+
+	return drm_gem_shmem_mmap(shmem, vma);
+}
+
+/*
+ * Driver ops
+ */
 
-struct sg_table *drm_gem_shmem_get_sg_table(struct drm_gem_object *obj);
 struct drm_gem_object *
 drm_gem_shmem_prime_import_sg_table(struct drm_device *dev,
 				    struct dma_buf_attachment *attach,
 				    struct sg_table *sgt);
-
-struct sg_table *drm_gem_shmem_get_pages_sgt(struct drm_gem_object *obj);
+int drm_gem_shmem_dumb_create(struct drm_file *file, struct drm_device *dev,
+			      struct drm_mode_create_dumb *args);
 
 /**
  * DRM_GEM_SHMEM_DRIVER_OPS - Default shmem GEM operations
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_mipi_dsi.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_mipi_dsi.h
@@ -166,6 +166,7 @@
  * struct mipi_dsi_device - DSI peripheral device
  * @host: DSI host for this peripheral
  * @dev: driver model device node for this peripheral
+ * @attached: the DSI device has been successfully attached
  * @name: DSI peripheral chip type
  * @channel: virtual channel assigned to the peripheral
  * @format: pixel format for video mode
@@ -181,6 +182,7 @@
 struct mipi_dsi_device {
 	struct mipi_dsi_host *host;
 	struct device dev;
+	bool attached;
 
 	char name[DSI_DEV_NAME_SIZE];
 	unsigned int channel;
@@ -227,16 +229,20 @@
 mipi_dsi_device_register_full(struct mipi_dsi_host *host,
 			      const struct mipi_dsi_device_info *info);
 void mipi_dsi_device_unregister(struct mipi_dsi_device *dsi);
+struct mipi_dsi_device *
+devm_mipi_dsi_device_register_full(struct device *dev, struct mipi_dsi_host *host,
+				   const struct mipi_dsi_device_info *info);
 struct mipi_dsi_device *of_find_mipi_dsi_device_by_node(struct device_node *np);
 int mipi_dsi_attach(struct mipi_dsi_device *dsi);
 int mipi_dsi_detach(struct mipi_dsi_device *dsi);
+int devm_mipi_dsi_attach(struct device *dev, struct mipi_dsi_device *dsi);
 int mipi_dsi_shutdown_peripheral(struct mipi_dsi_device *dsi);
 int mipi_dsi_turn_on_peripheral(struct mipi_dsi_device *dsi);
 int mipi_dsi_set_maximum_return_packet_size(struct mipi_dsi_device *dsi,
 					    u16 value);
-ssize_t mipi_dsi_compression_mode(struct mipi_dsi_device *dsi, bool enable);
-ssize_t mipi_dsi_picture_parameter_set(struct mipi_dsi_device *dsi,
-				       const struct drm_dsc_picture_parameter_set *pps);
+int mipi_dsi_compression_mode(struct mipi_dsi_device *dsi, bool enable);
+int mipi_dsi_picture_parameter_set(struct mipi_dsi_device *dsi,
+				   const struct drm_dsc_picture_parameter_set *pps);
 
 ssize_t mipi_dsi_generic_write(struct mipi_dsi_device *dsi, const void *payload,
 			       size_t size);
@@ -288,6 +294,10 @@
 					u16 brightness);
 int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi,
 					u16 *brightness);
+int mipi_dsi_dcs_set_display_brightness_large(struct mipi_dsi_device *dsi,
+					     u16 brightness);
+int mipi_dsi_dcs_get_display_brightness_large(struct mipi_dsi_device *dsi,
+					     u16 *brightness);
 
 /**
  * struct mipi_dsi_driver - DSI driver
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_mode_config.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_mode_config.h
@@ -856,6 +856,15 @@
 	struct drm_property *hdr_output_metadata_property;
 
 	/**
+	 * @gen_hdr_output_metadata_property: Connector property containing hdr
+	 * metadata. This will be provided by userspace compositors based
+	 * on HDR content. This is functionally the same as
+	 * hdr_output_metadata_property but it uses a generic, experimental
+	 * structure instead of the existing HDR10 specific structure
+	 */
+	struct drm_property *gen_hdr_output_metadata_property;
+
+	/**
 	 * @content_protection_property: DRM ENUM property for content
 	 * protection. See drm_connector_attach_content_protection_property().
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_print.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_print.h
@@ -121,7 +121,8 @@
 
 /**
  * struct drm_print_iterator - local struct used with drm_printer_coredump
- * @data: Pointer to the devcoredump output buffer
+ * @data: Pointer to the devcoredump output buffer, can be NULL if using
+ * drm_printer_coredump to determine size of devcoredump
  * @start: The offset within the buffer to start writing
  * @remain: The number of bytes to write for this iteration
  */
@@ -166,6 +167,57 @@
  *			coredump_read, ...)
  *	}
  *
+ * The above example has a time complexity of O(N^2), where N is the size of the
+ * devcoredump. This is acceptable for small devcoredumps but scales poorly for
+ * larger ones.
+ *
+ * Another use case for drm_coredump_printer is to capture the devcoredump into
+ * a saved buffer before the dev_coredump() callback. This involves two passes:
+ * one to determine the size of the devcoredump and another to print it to a
+ * buffer. Then, in dev_coredump(), copy from the saved buffer into the
+ * devcoredump read buffer.
+ *
+ * For example::
+ *
+ *	char *devcoredump_saved_buffer;
+ *
+ *	ssize_t __coredump_print(char *buffer, ssize_t count, ...)
+ *	{
+ *		struct drm_print_iterator iter;
+ *		struct drm_printer p;
+ *
+ *		iter.data = buffer;
+ *		iter.start = 0;
+ *		iter.remain = count;
+ *
+ *		p = drm_coredump_printer(&iter);
+ *
+ *		drm_printf(p, "foo=%d\n", foo);
+ *		...
+ *		return count - iter.remain;
+ *	}
+ *
+ *	void coredump_print(...)
+ *	{
+ *		ssize_t count;
+ *
+ *		count = __coredump_print(NULL, INT_MAX, ...);
+ *		devcoredump_saved_buffer = kvmalloc(count, GFP_KERNEL);
+ *		__coredump_print(devcoredump_saved_buffer, count, ...);
+ *	}
+ *
+ *	void coredump_read(char *buffer, loff_t offset, size_t count,
+ *			   void *data, size_t datalen)
+ *	{
+ *		...
+ *		memcpy(buffer, devcoredump_saved_buffer + offset, count);
+ *		...
+ *	}
+ *
+ * The above example has a time complexity of O(N*2), where N is the size of the
+ * devcoredump. This scales better than the previous example for larger
+ * devcoredumps.
+ *
  * RETURNS:
  * The &drm_printer object
  */
@@ -444,7 +496,7 @@
 
 #define drm_dbg_core(drm, fmt, ...)					\
 	drm_dev_dbg((drm) ? (drm)->dev : NULL, DRM_UT_CORE, fmt, ##__VA_ARGS__)
-#define drm_dbg(drm, fmt, ...)						\
+#define drm_dbg_driver(drm, fmt, ...)						\
 	drm_dev_dbg((drm) ? (drm)->dev : NULL, DRM_UT_DRIVER, fmt, ##__VA_ARGS__)
 #define drm_dbg_kms(drm, fmt, ...)					\
 	drm_dev_dbg((drm) ? (drm)->dev : NULL, DRM_UT_KMS, fmt, ##__VA_ARGS__)
@@ -463,6 +515,7 @@
 #define drm_dbg_drmres(drm, fmt, ...)					\
 	drm_dev_dbg((drm) ? (drm)->dev : NULL, DRM_UT_DRMRES, fmt, ##__VA_ARGS__)
 
+#define drm_dbg(drm, fmt, ...)	drm_dbg_driver(drm, fmt, ##__VA_ARGS__)
 
 /*
  * printk based logging
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/drm_probe_helper.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/drm_probe_helper.h
@@ -18,6 +18,7 @@
 void drm_kms_helper_poll_init(struct drm_device *dev);
 void drm_kms_helper_poll_fini(struct drm_device *dev);
 bool drm_helper_hpd_irq_event(struct drm_device *dev);
+bool drm_connector_helper_hpd_irq_event(struct drm_connector *connector);
 void drm_kms_helper_hotplug_event(struct drm_device *dev);
 
 void drm_kms_helper_poll_disable(struct drm_device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/i915_pciids.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/i915_pciids.h
@@ -637,13 +637,11 @@
 /* ADL-S */
 #define INTEL_ADLS_IDS(info) \
 	INTEL_VGA_DEVICE(0x4680, info), \
-	INTEL_VGA_DEVICE(0x4681, info), \
 	INTEL_VGA_DEVICE(0x4682, info), \
-	INTEL_VGA_DEVICE(0x4683, info), \
 	INTEL_VGA_DEVICE(0x4688, info), \
-	INTEL_VGA_DEVICE(0x4689, info), \
+	INTEL_VGA_DEVICE(0x468A, info), \
+	INTEL_VGA_DEVICE(0x468B, info), \
 	INTEL_VGA_DEVICE(0x4690, info), \
-	INTEL_VGA_DEVICE(0x4691, info), \
 	INTEL_VGA_DEVICE(0x4692, info), \
 	INTEL_VGA_DEVICE(0x4693, info)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/ttm/ttm_bo_api.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/ttm/ttm_bo_api.h
@@ -594,8 +594,7 @@
 
 vm_fault_t ttm_bo_vm_fault_reserved(struct vm_fault *vmf,
 				    pgprot_t prot,
-				    pgoff_t num_prefault,
-				    pgoff_t fault_page_size);
+				    pgoff_t num_prefault);
 
 vm_fault_t ttm_bo_vm_fault(struct vm_fault *vmf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/drm/ttm/ttm_resource.h
+++ linux-xilinx-zynqmp-5.15.0/include/drm/ttm/ttm_resource.h
@@ -262,6 +262,9 @@
 void ttm_resource_init(struct ttm_buffer_object *bo,
                        const struct ttm_place *place,
                        struct ttm_resource *res);
+void ttm_resource_fini(struct ttm_resource_manager *man,
+		       struct ttm_resource *res);
+
 int ttm_resource_alloc(struct ttm_buffer_object *bo,
 		       const struct ttm_place *place,
 		       struct ttm_resource **res);
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/clock/imx8mn-clock.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/clock/imx8mn-clock.h
@@ -19,7 +19,8 @@
 #define IMX8MN_VIDEO_PLL1_REF_SEL		10
 #define IMX8MN_DRAM_PLL_REF_SEL			11
 #define IMX8MN_GPU_PLL_REF_SEL			12
-#define IMX8MN_VPU_PLL_REF_SEL			13
+#define IMX8MN_M7_ALT_PLL_REF_SEL		13
+#define IMX8MN_VPU_PLL_REF_SEL			IMX8MN_M7_ALT_PLL_REF_SEL
 #define IMX8MN_ARM_PLL_REF_SEL			14
 #define IMX8MN_SYS_PLL1_REF_SEL			15
 #define IMX8MN_SYS_PLL2_REF_SEL			16
@@ -29,7 +30,8 @@
 #define IMX8MN_VIDEO_PLL1			20
 #define IMX8MN_DRAM_PLL				21
 #define IMX8MN_GPU_PLL				22
-#define IMX8MN_VPU_PLL				23
+#define IMX8MN_M7_ALT_PLL			23
+#define IMX8MN_VPU_PLL				IMX8MN_M7_ALT_PLL
 #define IMX8MN_ARM_PLL				24
 #define IMX8MN_SYS_PLL1				25
 #define IMX8MN_SYS_PLL2				26
@@ -39,7 +41,8 @@
 #define IMX8MN_VIDEO_PLL1_BYPASS		30
 #define IMX8MN_DRAM_PLL_BYPASS			31
 #define IMX8MN_GPU_PLL_BYPASS			32
-#define IMX8MN_VPU_PLL_BYPASS			33
+#define IMX8MN_M7_ALT_PLL_BYPASS		33
+#define IMX8MN_VPU_PLL_BYPASS			IMX8MN_M7_ALT_PLL_BYPASS
 #define IMX8MN_ARM_PLL_BYPASS			34
 #define IMX8MN_SYS_PLL1_BYPASS			35
 #define IMX8MN_SYS_PLL2_BYPASS			36
@@ -49,7 +52,8 @@
 #define IMX8MN_VIDEO_PLL1_OUT			40
 #define IMX8MN_DRAM_PLL_OUT			41
 #define IMX8MN_GPU_PLL_OUT			42
-#define IMX8MN_VPU_PLL_OUT			43
+#define IMX8MN_M7_ALT_PLL_OUT			43
+#define IMX8MN_VPU_PLL_OUT			IMX8MN_M7_ALT_PLL_OUT
 #define IMX8MN_ARM_PLL_OUT			44
 #define IMX8MN_SYS_PLL1_OUT			45
 #define IMX8MN_SYS_PLL2_OUT			46
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/clock/imx8mp-clock.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/clock/imx8mp-clock.h
@@ -318,8 +318,16 @@
 #define IMX8MP_CLK_AUDIO_AXI			310
 #define IMX8MP_CLK_HSIO_AXI			311
 #define IMX8MP_CLK_MEDIA_ISP			312
+#define IMX8MP_CLK_MEDIA_DISP2_PIX		313
+#define IMX8MP_CLK_CLKOUT1_SEL			314
+#define IMX8MP_CLK_CLKOUT1_DIV			315
+#define IMX8MP_CLK_CLKOUT1			316
+#define IMX8MP_CLK_CLKOUT2_SEL			317
+#define IMX8MP_CLK_CLKOUT2_DIV			318
+#define IMX8MP_CLK_CLKOUT2			319
+#define IMX8MP_CLK_USB_SUSP			320
 
-#define IMX8MP_CLK_END				313
+#define IMX8MP_CLK_END				321
 
 #define IMX8MP_CLK_AUDIOMIX_SAI1_IPG		0
 #define IMX8MP_CLK_AUDIOMIX_SAI1_MCLK1		1
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/clock/qcom,gcc-msm8939.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/clock/qcom,gcc-msm8939.h
@@ -192,6 +192,7 @@
 #define GCC_VENUS0_CORE0_VCODEC0_CLK		183
 #define GCC_VENUS0_CORE1_VCODEC0_CLK		184
 #define GCC_OXILI_TIMER_CLK			185
+#define SYSTEM_MM_NOC_BFDCD_CLK_SRC		186
 
 /* Indexes for GDSCs */
 #define BIMC_GDSC				0
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/clock/qcom,gcc-sc8180x.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/clock/qcom,gcc-sc8180x.h
@@ -246,6 +246,9 @@
 #define GCC_PCIE_3_CLKREF_CLK					236
 #define GCC_USB3_PRIM_CLKREF_CLK				237
 #define GCC_USB3_SEC_CLKREF_CLK					238
+#define GCC_UFS_MEM_CLKREF_EN					239
+#define GCC_UFS_CARD_CLKREF_EN					240
+#define GPLL9							241
 
 #define GCC_EMAC_BCR						0
 #define GCC_GPU_BCR						1
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/clock/qcom,videocc-sm8150.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/clock/qcom,videocc-sm8150.h
@@ -16,6 +16,10 @@
 
 /* VIDEO_CC Resets */
 #define VIDEO_CC_MVSC_CORE_CLK_BCR	0
+#define VIDEO_CC_INTERFACE_BCR		1
+#define VIDEO_CC_MVS0_BCR		2
+#define VIDEO_CC_MVS1_BCR		3
+#define VIDEO_CC_MVSC_BCR		4
 
 /* VIDEO_CC GDSCRs */
 #define VENUS_GDSC			0
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/drm/mipi-dsi.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/drm/mipi-dsi.h
@@ -0,0 +1,11 @@
+#ifndef __DT_BINDINGS_DRM__
+#define __DT_BINDINGS_DRM__
+/*
+ * MIPI DSI pixel formats as defined in the include/drm/drm_mipi_dsi.h"
+ */
+#define MIPI_DSI_FMT_RGB888		0
+#define MIPI_DSI_FMT_RGB666		1
+#define MIPI_DSI_FMT_RGB666_PACKED	2
+#define MIPI_DSI_FMT_RGB565		3
+
+#endif /* _DT_BINDINGS_DRM__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/media/xilinx-vip.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/media/xilinx-vip.h
@@ -32,5 +32,11 @@
 #define XVIP_VF_CUSTOM2			13
 #define XVIP_VF_CUSTOM3			14
 #define XVIP_VF_CUSTOM4			15
+#define XVIP_VF_VUY_422			16
+#define XVIP_VF_BGRX			17
+#define XVIP_VF_YUVX			18
+#define XVIP_VF_XBGR			19
+#define XVIP_VF_Y_GREY			20
+#define XVIP_VF_XRGB			21
 
 #endif /* __DT_BINDINGS_MEDIA_XILINX_VIP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/net/mscc-phy-vsc8531.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/net/mscc-phy-vsc8531.h
@@ -28,4 +28,13 @@
 #define VSC8531_FORCE_LED_OFF           14
 #define VSC8531_FORCE_LED_ON            15
 
+#define VSC8531_RGMII_CLK_DELAY_0_2_NS	0
+#define VSC8531_RGMII_CLK_DELAY_0_8_NS	1
+#define VSC8531_RGMII_CLK_DELAY_1_1_NS	2
+#define VSC8531_RGMII_CLK_DELAY_1_7_NS	3
+#define VSC8531_RGMII_CLK_DELAY_2_0_NS	4
+#define VSC8531_RGMII_CLK_DELAY_2_3_NS	5
+#define VSC8531_RGMII_CLK_DELAY_2_6_NS	6
+#define VSC8531_RGMII_CLK_DELAY_3_4_NS	7
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/power/xlnx-versal-power.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/power/xlnx-versal-power.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *  Copyright (C) 2019 - 2021 Xilinx, Inc.
+ */
+
+#ifndef _DT_BINDINGS_VERSAL_POWER_H
+#define _DT_BINDINGS_VERSAL_POWER_H
+
+#define PM_DEV_RPU0_0				(0x18110005U)
+#define PM_DEV_RPU0_1				(0x18110006U)
+#define PM_DEV_OCM_0				(0x18314007U)
+#define PM_DEV_OCM_1				(0x18314008U)
+#define PM_DEV_OCM_2				(0x18314009U)
+#define PM_DEV_OCM_3				(0x1831400aU)
+#define PM_DEV_TCM_0_A				(0x1831800bU)
+#define PM_DEV_TCM_0_B				(0x1831800cU)
+#define PM_DEV_TCM_1_A				(0x1831800dU)
+#define PM_DEV_TCM_1_B				(0x1831800eU)
+#define PM_DEV_USB_0				(0x18224018U)
+#define PM_DEV_GEM_0				(0x18224019U)
+#define PM_DEV_GEM_1				(0x1822401aU)
+#define PM_DEV_SPI_0				(0x1822401bU)
+#define PM_DEV_SPI_1				(0x1822401cU)
+#define PM_DEV_I2C_0				(0x1822401dU)
+#define PM_DEV_I2C_1				(0x1822401eU)
+#define PM_DEV_CAN_FD_0				(0x1822401fU)
+#define PM_DEV_CAN_FD_1				(0x18224020U)
+#define PM_DEV_UART_0				(0x18224021U)
+#define PM_DEV_UART_1				(0x18224022U)
+#define PM_DEV_GPIO				(0x18224023U)
+#define PM_DEV_TTC_0				(0x18224024U)
+#define PM_DEV_TTC_1				(0x18224025U)
+#define PM_DEV_TTC_2				(0x18224026U)
+#define PM_DEV_TTC_3				(0x18224027U)
+#define PM_DEV_SWDT_FPD				(0x18224029U)
+#define PM_DEV_OSPI				(0x1822402aU)
+#define PM_DEV_QSPI				(0x1822402bU)
+#define PM_DEV_GPIO_PMC				(0x1822402cU)
+#define PM_DEV_I2C_PMC				(0x1822402dU)
+#define PM_DEV_SDIO_0				(0x1822402eU)
+#define PM_DEV_SDIO_1				(0x1822402fU)
+#define PM_DEV_RTC				(0x18224034U)
+#define PM_DEV_ADMA_0				(0x18224035U)
+#define PM_DEV_ADMA_1				(0x18224036U)
+#define PM_DEV_ADMA_2				(0x18224037U)
+#define PM_DEV_ADMA_3				(0x18224038U)
+#define PM_DEV_ADMA_4				(0x18224039U)
+#define PM_DEV_ADMA_5				(0x1822403aU)
+#define PM_DEV_ADMA_6				(0x1822403bU)
+#define PM_DEV_ADMA_7				(0x1822403cU)
+#define PM_DEV_AMS_ROOT				(0x18224055U)
+#define PM_DEV_AI				(0x18224072U)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/dt-bindings/power/xlnx-zynqmp-power.h
+++ linux-xilinx-zynqmp-5.15.0/include/dt-bindings/power/xlnx-zynqmp-power.h
@@ -6,6 +6,16 @@
 #ifndef _DT_BINDINGS_ZYNQMP_POWER_H
 #define _DT_BINDINGS_ZYNQMP_POWER_H
 
+#define		PD_RPU_0	6
+#define		PD_RPU_1	7
+#define		PD_OCM_BANK_0	11
+#define		PD_OCM_BANK_1	12
+#define		PD_OCM_BANK_2	13
+#define		PD_OCM_BANK_3	14
+#define		PD_TCM_BANK_0	15
+#define		PD_TCM_BANK_1	16
+#define		PD_TCM_BANK_2	17
+#define		PD_TCM_BANK_3	18
 #define		PD_USB_0	22
 #define		PD_USB_1	23
 #define		PD_TTC_0	24
@@ -35,5 +45,6 @@
 #define		PD_CAN_1	48
 #define		PD_GPU		58
 #define		PD_PCIE		59
+#define		PD_PL		69
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/keys/trusted-type.h
+++ linux-xilinx-zynqmp-5.15.0/include/keys/trusted-type.h
@@ -64,7 +64,7 @@
 	/* Unseal a key. */
 	int (*unseal)(struct trusted_key_payload *p, char *datablob);
 
-	/* Get a randomized key. */
+	/* Optional: Get a randomized key. */
 	int (*get_random)(unsigned char *key, size_t key_len);
 
 	/* Exit key interface. */
--- linux-xilinx-zynqmp-5.15.0.orig/include/kvm/arm_vgic.h
+++ linux-xilinx-zynqmp-5.15.0/include/kvm/arm_vgic.h
@@ -423,6 +423,6 @@
 
 int vgic_v4_load(struct kvm_vcpu *vcpu);
 void vgic_v4_commit(struct kvm_vcpu *vcpu);
-int vgic_v4_put(struct kvm_vcpu *vcpu, bool need_db);
+int vgic_v4_put(struct kvm_vcpu *vcpu);
 
 #endif /* __KVM_ARM_VGIC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/acpi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/acpi.h
@@ -484,6 +484,7 @@
 			   void *preproc_data);
 int acpi_dev_get_dma_resources(struct acpi_device *adev,
 			       struct list_head *list);
+int acpi_dev_get_memory_resources(struct acpi_device *adev, struct list_head *list);
 int acpi_dev_filter_resource_type(struct acpi_resource *ares,
 				  unsigned long types);
 
@@ -560,6 +561,8 @@
 extern bool osc_sb_apei_support_acked;
 extern bool osc_pc_lpi_support_confirmed;
 extern bool osc_sb_native_usb4_support_confirmed;
+extern bool osc_sb_cppc2_support_acked;
+extern bool osc_cpc_flexible_adr_space_confirmed;
 
 /* USB4 Capabilities */
 #define OSC_USB_USB3_TUNNELING			0x00000001
@@ -976,6 +979,15 @@
 	return -ENODEV;
 }
 
+static inline int acpi_register_wakeup_handler(int wake_irq,
+	bool (*wakeup)(void *context), void *context)
+{
+	return -ENXIO;
+}
+
+static inline void acpi_unregister_wakeup_handler(
+	bool (*wakeup)(void *context), void *context) { }
+
 #endif	/* !CONFIG_ACPI */
 
 #ifdef CONFIG_ACPI_HOTPLUG_IOAPIC
@@ -996,7 +1008,15 @@
 
 acpi_status acpi_os_prepare_extended_sleep(u8 sleep_state,
 					   u32 val_a, u32 val_b);
-
+#ifdef CONFIG_X86
+struct acpi_s2idle_dev_ops {
+	struct list_head list_node;
+	void (*prepare)(void);
+	void (*restore)(void);
+};
+int acpi_register_lps0_dev(struct acpi_s2idle_dev_ops *arg);
+void acpi_unregister_lps0_dev(struct acpi_s2idle_dev_ops *arg);
+#endif /* CONFIG_X86 */
 #ifndef CONFIG_IA64
 void arch_reserve_mem_area(acpi_physical_address addr, size_t size);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/acpi_iort.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/acpi_iort.h
@@ -21,6 +21,7 @@
  */
 #define IORT_SMMU_V3_PMCG_GENERIC        0x00000000 /* Generic SMMUv3 PMCG */
 #define IORT_SMMU_V3_PMCG_HISI_HIP08     0x00000001 /* HiSilicon HIP08 PMCG */
+#define IORT_SMMU_V3_PMCG_HISI_HIP09     0x00000002 /* HiSilicon HIP09 PMCG */
 
 int iort_register_domain_token(int trans_id, phys_addr_t base,
 			       struct fwnode_handle *fw_node);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/acpi_mdio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/acpi_mdio.h
@@ -9,7 +9,14 @@
 #include <linux/phy.h>
 
 #if IS_ENABLED(CONFIG_ACPI_MDIO)
-int acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *fwnode);
+int __acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *fwnode,
+			    struct module *owner);
+
+static inline int
+acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *handle)
+{
+	return __acpi_mdiobus_register(mdio, handle, THIS_MODULE);
+}
 #else /* CONFIG_ACPI_MDIO */
 static inline int
 acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *fwnode)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/acpi_viot.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/acpi_viot.h
@@ -6,9 +6,11 @@
 #include <linux/acpi.h>
 
 #ifdef CONFIG_ACPI_VIOT
+void __init acpi_viot_early_init(void);
 void __init acpi_viot_init(void);
 int viot_iommu_configure(struct device *dev);
 #else
+static inline void acpi_viot_early_init(void) {}
 static inline void acpi_viot_init(void) {}
 static inline int viot_iommu_configure(struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ahci_platform.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ahci_platform.h
@@ -23,6 +23,8 @@
 void ahci_platform_disable_phys(struct ahci_host_priv *hpriv);
 int ahci_platform_enable_clks(struct ahci_host_priv *hpriv);
 void ahci_platform_disable_clks(struct ahci_host_priv *hpriv);
+int ahci_platform_deassert_rsts(struct ahci_host_priv *hpriv);
+int ahci_platform_assert_rsts(struct ahci_host_priv *hpriv);
 int ahci_platform_enable_regulators(struct ahci_host_priv *hpriv);
 void ahci_platform_disable_regulators(struct ahci_host_priv *hpriv);
 int ahci_platform_enable_resources(struct ahci_host_priv *hpriv);
@@ -41,6 +43,7 @@
 int ahci_platform_suspend(struct device *dev);
 int ahci_platform_resume(struct device *dev);
 
-#define AHCI_PLATFORM_GET_RESETS	0x01
+#define AHCI_PLATFORM_GET_RESETS	BIT(0)
+#define AHCI_PLATFORM_RST_TRIGGER	BIT(1)
 
 #endif /* _AHCI_PLATFORM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/arm-smccc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/arm-smccc.h
@@ -92,6 +92,11 @@
 			   ARM_SMCCC_SMC_32,				\
 			   0, 0x7fff)
 
+#define ARM_SMCCC_ARCH_WORKAROUND_3					\
+	ARM_SMCCC_CALL_VAL(ARM_SMCCC_FAST_CALL,				\
+			   ARM_SMCCC_SMC_32,				\
+			   0, 0x3fff)
+
 #define ARM_SMCCC_VENDOR_HYP_CALL_UID_FUNC_ID				\
 	ARM_SMCCC_CALL_VAL(ARM_SMCCC_FAST_CALL,				\
 			   ARM_SMCCC_SMC_32,				\
@@ -219,8 +224,6 @@
 
 void __init arm_smccc_version_init(u32 version, enum arm_smccc_conduit conduit);
 
-extern u64 smccc_has_sve_hint;
-
 /**
  * struct arm_smccc_res - Result from SMC/HVC call
  * @a0-a3 result values from registers 0 to 3
@@ -301,15 +304,6 @@
 };
 
 /**
- * __arm_smccc_sve_check() - Set the SVE hint bit when doing SMC calls
- *
- * Sets the SMCCC hint bit to indicate if there is live state in the SVE
- * registers, this modifies x0 in place and should never be called from C
- * code.
- */
-asmlinkage unsigned long __arm_smccc_sve_check(unsigned long x0);
-
-/**
  * __arm_smccc_smc() - make SMC calls
  * @a0-a7: arguments passed in registers 0 to 7
  * @res: result values from registers 0 to 3
@@ -376,20 +370,6 @@
 
 #endif
 
-/* nVHE hypervisor doesn't have a current thread so needs separate checks */
-#if defined(CONFIG_ARM64_SVE) && !defined(__KVM_NVHE_HYPERVISOR__)
-
-#define SMCCC_SVE_CHECK ALTERNATIVE("nop \n",  "bl __arm_smccc_sve_check \n", \
-				    ARM64_SVE)
-#define smccc_sve_clobbers "x16", "x30", "cc",
-
-#else
-
-#define SMCCC_SVE_CHECK
-#define smccc_sve_clobbers
-
-#endif
-
 #define ___count_args(_0, _1, _2, _3, _4, _5, _6, _7, _8, x, ...) x
 
 #define __count_args(...)						\
@@ -457,7 +437,7 @@
 
 #define ___constraints(count)						\
 	: __constraint_read_ ## count					\
-	: smccc_sve_clobbers "memory"
+	: "memory"
 #define __constraints(count)	___constraints(count)
 
 /*
@@ -472,8 +452,7 @@
 		register unsigned long r2 asm("r2");			\
 		register unsigned long r3 asm("r3"); 			\
 		__declare_args(__count_args(__VA_ARGS__), __VA_ARGS__);	\
-		asm volatile(SMCCC_SVE_CHECK				\
-			     inst "\n" :				\
+		asm volatile(inst "\n" :				\
 			     "=r" (r0), "=r" (r1), "=r" (r2), "=r" (r3)	\
 			     __constraints(__count_args(__VA_ARGS__)));	\
 		if (___res)						\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/arm_ffa.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/arm_ffa.h
@@ -13,6 +13,7 @@
 
 /* FFA Bus/Device/Driver related */
 struct ffa_device {
+	u32 id;
 	int vm_id;
 	bool mode_32bit;
 	uuid_t uuid;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/arm_sdei.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/arm_sdei.h
@@ -46,9 +46,13 @@
 /* For use by arch code when CPU hotplug notifiers are not appropriate. */
 int sdei_mask_local_cpu(void);
 int sdei_unmask_local_cpu(void);
+void __init sdei_init(void);
+void sdei_handler_abort(void);
 #else
 static inline int sdei_mask_local_cpu(void) { return 0; }
 static inline int sdei_unmask_local_cpu(void) { return 0; }
+static inline void sdei_init(void) { }
+static inline void sdei_handler_abort(void) { }
 #endif /* CONFIG_ARM_SDE_INTERFACE */
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/async.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/async.h
@@ -90,6 +90,8 @@
 	return async_schedule_node(func, dev, dev_to_node(dev));
 }
 
+bool async_schedule_dev_nocall(async_func_t func, struct device *dev);
+
 /**
  * async_schedule_dev_domain - A device specific version of async_schedule_domain
  * @func: function to execute asynchronously
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ata.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ata.h
@@ -565,6 +565,18 @@
 	((((id)[ATA_ID_SATA_CAPABILITY] != 0x0000) && \
 	  ((id)[ATA_ID_SATA_CAPABILITY] != 0xffff)) && \
 	 ((id)[ATA_ID_FEATURE_SUPP] & (1 << 2)))
+#define ata_id_has_devslp(id)	\
+	((((id)[ATA_ID_SATA_CAPABILITY] != 0x0000) && \
+	  ((id)[ATA_ID_SATA_CAPABILITY] != 0xffff)) && \
+	 ((id)[ATA_ID_FEATURE_SUPP] & (1 << 8)))
+#define ata_id_has_ncq_autosense(id) \
+	((((id)[ATA_ID_SATA_CAPABILITY] != 0x0000) && \
+	  ((id)[ATA_ID_SATA_CAPABILITY] != 0xffff)) && \
+	 ((id)[ATA_ID_FEATURE_SUPP] & (1 << 7)))
+#define ata_id_has_dipm(id)	\
+	((((id)[ATA_ID_SATA_CAPABILITY] != 0x0000) && \
+	  ((id)[ATA_ID_SATA_CAPABILITY] != 0xffff)) && \
+	 ((id)[ATA_ID_FEATURE_SUPP] & (1 << 3)))
 #define ata_id_iordy_disable(id) ((id)[ATA_ID_CAPABILITY] & (1 << 10))
 #define ata_id_has_iordy(id) ((id)[ATA_ID_CAPABILITY] & (1 << 11))
 #define ata_id_u32(id,n)	\
@@ -577,9 +589,6 @@
 
 #define ata_id_cdb_intr(id)	(((id)[ATA_ID_CONFIG] & 0x60) == 0x20)
 #define ata_id_has_da(id)	((id)[ATA_ID_SATA_CAPABILITY_2] & (1 << 4))
-#define ata_id_has_devslp(id)	((id)[ATA_ID_FEATURE_SUPP] & (1 << 8))
-#define ata_id_has_ncq_autosense(id) \
-				((id)[ATA_ID_FEATURE_SUPP] & (1 << 7))
 
 static inline bool ata_id_has_hipm(const u16 *id)
 {
@@ -591,17 +600,6 @@
 	return val & (1 << 9);
 }
 
-static inline bool ata_id_has_dipm(const u16 *id)
-{
-	u16 val = id[ATA_ID_FEATURE_SUPP];
-
-	if (val == 0 || val == 0xffff)
-		return false;
-
-	return val & (1 << 3);
-}
-
-
 static inline bool ata_id_has_fua(const u16 *id)
 {
 	if ((id[ATA_ID_CFSSE] & 0xC000) != 0x4000)
@@ -770,16 +768,21 @@
 
 static inline bool ata_id_has_sense_reporting(const u16 *id)
 {
-	if (!(id[ATA_ID_CFS_ENABLE_2] & (1 << 15)))
+	if (!(id[ATA_ID_CFS_ENABLE_2] & BIT(15)))
+		return false;
+	if ((id[ATA_ID_COMMAND_SET_3] & (BIT(15) | BIT(14))) != BIT(14))
 		return false;
-	return id[ATA_ID_COMMAND_SET_3] & (1 << 6);
+	return id[ATA_ID_COMMAND_SET_3] & BIT(6);
 }
 
 static inline bool ata_id_sense_reporting_enabled(const u16 *id)
 {
-	if (!(id[ATA_ID_CFS_ENABLE_2] & (1 << 15)))
+	if (!ata_id_has_sense_reporting(id))
+		return false;
+	/* ata_id_has_sense_reporting() == true, word 86 must have bit 15 set */
+	if ((id[ATA_ID_COMMAND_SET_4] & (BIT(15) | BIT(14))) != BIT(14))
 		return false;
-	return id[ATA_ID_COMMAND_SET_4] & (1 << 6);
+	return id[ATA_ID_COMMAND_SET_4] & BIT(6);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/atomic/atomic-arch-fallback.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/atomic/atomic-arch-fallback.h
@@ -151,7 +151,16 @@
 static __always_inline int
 arch_atomic_read_acquire(const atomic_t *v)
 {
-	return smp_load_acquire(&(v)->counter);
+	int ret;
+
+	if (__native_word(atomic_t)) {
+		ret = smp_load_acquire(&(v)->counter);
+	} else {
+		ret = arch_atomic_read(v);
+		__atomic_acquire_fence();
+	}
+
+	return ret;
 }
 #define arch_atomic_read_acquire arch_atomic_read_acquire
 #endif
@@ -160,7 +169,12 @@
 static __always_inline void
 arch_atomic_set_release(atomic_t *v, int i)
 {
-	smp_store_release(&(v)->counter, i);
+	if (__native_word(atomic_t)) {
+		smp_store_release(&(v)->counter, i);
+	} else {
+		__atomic_release_fence();
+		arch_atomic_set(v, i);
+	}
 }
 #define arch_atomic_set_release arch_atomic_set_release
 #endif
@@ -1258,7 +1272,16 @@
 static __always_inline s64
 arch_atomic64_read_acquire(const atomic64_t *v)
 {
-	return smp_load_acquire(&(v)->counter);
+	s64 ret;
+
+	if (__native_word(atomic64_t)) {
+		ret = smp_load_acquire(&(v)->counter);
+	} else {
+		ret = arch_atomic64_read(v);
+		__atomic_acquire_fence();
+	}
+
+	return ret;
 }
 #define arch_atomic64_read_acquire arch_atomic64_read_acquire
 #endif
@@ -1267,7 +1290,12 @@
 static __always_inline void
 arch_atomic64_set_release(atomic64_t *v, s64 i)
 {
-	smp_store_release(&(v)->counter, i);
+	if (__native_word(atomic64_t)) {
+		smp_store_release(&(v)->counter, i);
+	} else {
+		__atomic_release_fence();
+		arch_atomic64_set(v, i);
+	}
 }
 #define arch_atomic64_set_release arch_atomic64_set_release
 #endif
@@ -2358,4 +2386,4 @@
 #endif
 
 #endif /* _LINUX_ATOMIC_FALLBACK_H */
-// cca554917d7ea73d5e3e7397dd70c484cad9b2c4
+// 8e2cc06bc0d2c0967d2f8424762bd48555ee40ae
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/audit.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/audit.h
@@ -11,6 +11,7 @@
 
 #include <linux/sched.h>
 #include <linux/ptrace.h>
+#include <linux/security.h>
 #include <uapi/linux/audit.h>
 #include <uapi/linux/netfilter/nf_tables.h>
 
@@ -65,8 +66,9 @@
 		kuid_t			uid;
 		kgid_t			gid;
 		struct {
+			bool		lsm_isset;
 			char		*lsm_str;
-			void		*lsm_rule;
+			void		*lsm_rules[LSMBLOB_ENTRIES];
 		};
 	};
 	u32				op;
@@ -184,7 +186,11 @@
 						  const char *operation);
 extern void		    audit_log_lost(const char *message);
 
-extern int audit_log_task_context(struct audit_buffer *ab);
+extern void audit_log_lsm(struct lsmblob *blob, bool exiting);
+extern int audit_log_task_context(struct audit_buffer *ab,
+				  struct lsmblob *blob);
+extern int audit_log_object_context(struct audit_buffer *ab,
+				    struct lsmblob *blob);
 extern void audit_log_task_info(struct audit_buffer *ab);
 
 extern int		    audit_update_lsm_rules(void);
@@ -244,7 +250,10 @@
 { }
 static inline void audit_log_path_denied(int type, const char *operation)
 { }
-static inline int audit_log_task_context(struct audit_buffer *ab)
+static inline void audit_log_lsm(struct lsmblob *blob, bool exiting)
+{ }
+static inline int audit_log_task_context(struct audit_buffer *ab,
+					 struct lsmblob *blob)
 {
 	return 0;
 }
@@ -302,6 +311,7 @@
 extern void audit_seccomp_actions_logged(const char *names,
 					 const char *old_names, int res);
 extern void __audit_ptrace(struct task_struct *t);
+extern void audit_stamp_context(struct audit_context *ctx);
 
 static inline void audit_set_context(struct task_struct *task, struct audit_context *ctx)
 {
@@ -672,6 +682,9 @@
 static inline void audit_ptrace(struct task_struct *t)
 { }
 
+static inline void audit_stamp_context(struct audit_context *ctx)
+{ }
+
 static inline void audit_log_nfcfg(const char *name, u8 af,
 				   unsigned int nentries,
 				   enum audit_nfcfgop op, gfp_t gfp)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/backing-dev.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/backing-dev.h
@@ -121,6 +121,8 @@
 
 extern struct backing_dev_info noop_backing_dev_info;
 
+int bdi_init(struct backing_dev_info *bdi);
+
 /**
  * writeback_in_progress - determine whether there is writeback in progress
  * @wb: bdi_writeback of interest
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/binfmts.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/binfmts.h
@@ -87,6 +87,9 @@
 	loff_t written;
 	loff_t pos;
 	loff_t to_skip;
+	int vma_count;
+	size_t vma_data_size;
+	struct core_vma_metadata *vma_meta;
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bitfield.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bitfield.h
@@ -41,6 +41,22 @@
 
 #define __bf_shf(x) (__builtin_ffsll(x) - 1)
 
+#define __scalar_type_to_unsigned_cases(type)				\
+		unsigned type:	(unsigned type)0,			\
+		signed type:	(unsigned type)0
+
+#define __unsigned_scalar_typeof(x) typeof(				\
+		_Generic((x),						\
+			char:	(unsigned char)0,			\
+			__scalar_type_to_unsigned_cases(char),		\
+			__scalar_type_to_unsigned_cases(short),		\
+			__scalar_type_to_unsigned_cases(int),		\
+			__scalar_type_to_unsigned_cases(long),		\
+			__scalar_type_to_unsigned_cases(long long),	\
+			default: (x)))
+
+#define __bf_cast_unsigned(type, x)	((__unsigned_scalar_typeof(type))(x))
+
 #define __BF_FIELD_CHECK(_mask, _reg, _val, _pfx)			\
 	({								\
 		BUILD_BUG_ON_MSG(!__builtin_constant_p(_mask),		\
@@ -49,7 +65,8 @@
 		BUILD_BUG_ON_MSG(__builtin_constant_p(_val) ?		\
 				 ~((_mask) >> __bf_shf(_mask)) & (_val) : 0, \
 				 _pfx "value too large for the field"); \
-		BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull,		\
+		BUILD_BUG_ON_MSG(__bf_cast_unsigned(_mask, _mask) >	\
+				 __bf_cast_unsigned(_reg, ~0ull),	\
 				 _pfx "type of reg too small for mask"); \
 		__BUILD_BUG_ON_NOT_POWER_OF_2((_mask) +			\
 					      (1ULL << __bf_shf(_mask))); \
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bitmap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bitmap.h
@@ -236,22 +236,24 @@
 #define BITMAP_FIRST_WORD_MASK(start) (~0UL << ((start) & (BITS_PER_LONG - 1)))
 #define BITMAP_LAST_WORD_MASK(nbits) (~0UL >> (-(nbits) & (BITS_PER_LONG - 1)))
 
+#define bitmap_size(nbits)	(ALIGN(nbits, BITS_PER_LONG) / BITS_PER_BYTE)
+
 static inline void bitmap_zero(unsigned long *dst, unsigned int nbits)
 {
-	unsigned int len = BITS_TO_LONGS(nbits) * sizeof(unsigned long);
+	unsigned int len = bitmap_size(nbits);
 	memset(dst, 0, len);
 }
 
 static inline void bitmap_fill(unsigned long *dst, unsigned int nbits)
 {
-	unsigned int len = BITS_TO_LONGS(nbits) * sizeof(unsigned long);
+	unsigned int len = bitmap_size(nbits);
 	memset(dst, 0xff, len);
 }
 
 static inline void bitmap_copy(unsigned long *dst, const unsigned long *src,
 			unsigned int nbits)
 {
-	unsigned int len = BITS_TO_LONGS(nbits) * sizeof(unsigned long);
+	unsigned int len = bitmap_size(nbits);
 	memcpy(dst, src, len);
 }
 
@@ -266,6 +268,18 @@
 		dst[nbits / BITS_PER_LONG] &= BITMAP_LAST_WORD_MASK(nbits);
 }
 
+static inline void bitmap_copy_and_extend(unsigned long *to,
+					  const unsigned long *from,
+					  unsigned int count, unsigned int size)
+{
+	unsigned int copy = BITS_TO_LONGS(count);
+
+	memcpy(to, from, copy * sizeof(long));
+	if (count % BITS_PER_LONG)
+		to[copy - 1] &= BITMAP_LAST_WORD_MASK(count);
+	memset(to + copy, 0, bitmap_size(size) - copy * sizeof(long));
+}
+
 /*
  * On 32-bit systems bitmaps are represented as u32 arrays internally, and
  * therefore conversion is not needed when copying data from/to arrays of u32.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/blk-cgroup.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/blk-cgroup.h
@@ -24,6 +24,7 @@
 #include <linux/atomic.h>
 #include <linux/kthread.h>
 #include <linux/fs.h>
+#include <linux/blk-mq.h>
 
 /* percpu_counter batch for blkg_[rw]stats, per-cpu drift doesn't matter */
 #define BLKG_STAT_CPU_BATCH	(INT_MAX / 2)
@@ -432,10 +433,14 @@
 static inline void blkcg_unpin_online(struct blkcg *blkcg)
 {
 	do {
+		struct blkcg *parent;
+
 		if (!refcount_dec_and_test(&blkcg->online_pin))
 			break;
+
+		parent = blkcg_parent(blkcg);
 		blkcg_destroy_blkgs(blkcg);
-		blkcg = blkcg_parent(blkcg);
+		blkcg = parent;
 	} while (blkcg);
 }
 
@@ -604,6 +609,21 @@
 		atomic_dec(&blkg->blkcg->css.cgroup->congestion_count);
 }
 
+/**
+ * blk_cgroup_mergeable - Determine whether to allow or disallow merges
+ * @rq: request to merge into
+ * @bio: bio to merge
+ *
+ * @bio and @rq should belong to the same cgroup and their issue_as_root should
+ * match. The latter is necessary as we don't want to throttle e.g. a metadata
+ * update because it happens to be next to a regular IO.
+ */
+static inline bool blk_cgroup_mergeable(struct request *rq, struct bio *bio)
+{
+	return rq->bio->bi_blkg == bio->bi_blkg &&
+		bio_issue_as_root_blkg(rq->bio) == bio_issue_as_root_blkg(bio);
+}
+
 void blk_cgroup_bio_start(struct bio *bio);
 void blkcg_add_delay(struct blkcg_gq *blkg, u64 now, u64 delta);
 void blkcg_schedule_throttle(struct request_queue *q, bool use_memdelay);
@@ -659,6 +679,7 @@
 static inline bool blkcg_punt_bio_submit(struct bio *bio) { return false; }
 static inline void blkcg_bio_issue_init(struct bio *bio) { }
 static inline void blk_cgroup_bio_start(struct bio *bio) { }
+static inline bool blk_cgroup_mergeable(struct request *rq, struct bio *bio) { return true; }
 
 #define blk_queue_for_each_rl(rl, q)	\
 	for ((rl) = &(q)->root_rl; (rl); (rl) = NULL)
@@ -684,8 +705,8 @@
 		return -EINVAL;
 
 	cgrp = cgroup_get_from_id(cgrp_id);
-	if (!cgrp)
-		return -ENOENT;
+	if (IS_ERR(cgrp))
+		return PTR_ERR(cgrp);
 	css = cgroup_get_e_css(cgrp, &io_cgrp_subsys);
 	if (!css) {
 		ret = -ENOENT;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/blk-crypto.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/blk-crypto.h
@@ -97,8 +97,8 @@
 int blk_crypto_start_using_key(const struct blk_crypto_key *key,
 			       struct request_queue *q);
 
-int blk_crypto_evict_key(struct request_queue *q,
-			 const struct blk_crypto_key *key);
+void blk_crypto_evict_key(struct request_queue *q,
+			  const struct blk_crypto_key *key);
 
 bool blk_crypto_config_supported(struct request_queue *q,
 				 const struct blk_crypto_config *cfg);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/blk-pm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/blk-pm.h
@@ -14,7 +14,7 @@
 extern int blk_pre_runtime_suspend(struct request_queue *q);
 extern void blk_post_runtime_suspend(struct request_queue *q, int err);
 extern void blk_pre_runtime_resume(struct request_queue *q);
-extern void blk_post_runtime_resume(struct request_queue *q, int err);
+extern void blk_post_runtime_resume(struct request_queue *q);
 extern void blk_set_runtime_active(struct request_queue *q);
 #else
 static inline void blk_pm_runtime_init(struct request_queue *q,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/blk_types.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/blk_types.h
@@ -215,9 +215,8 @@
 struct bio {
 	struct bio		*bi_next;	/* request queue link */
 	struct block_device	*bi_bdev;
-	unsigned int		bi_opf;		/* bottom bits req flags,
-						 * top bits REQ_OP. Use
-						 * accessors.
+	unsigned int		bi_opf;		/* bottom bits REQ_OP, top bits
+						 * req_flags.
 						 */
 	unsigned short		bi_flags;	/* BIO_* below */
 	unsigned short		bi_ioprio;
@@ -295,7 +294,8 @@
 	BIO_TRACE_COMPLETION,	/* bio_endio() should trace the final completion
 				 * of this bio. */
 	BIO_CGROUP_ACCT,	/* has been accounted to a cgroup */
-	BIO_TRACKED,		/* set if bio goes through the rq_qos path */
+	BIO_QOS_THROTTLED,	/* bio went through rq_qos throttle path */
+	BIO_QOS_MERGED,		/* but went through rq_qos merge path */
 	BIO_REMAPPED,
 	BIO_ZONE_WRITE_LOCKED,	/* Owns a zoned device zone write lock */
 	BIO_PERCPU_CACHE,	/* can participate in per-cpu alloc cache */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/blkdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/blkdev.h
@@ -235,6 +235,14 @@
 	void *end_io_data;
 };
 
+static inline int blk_validate_block_size(unsigned long bsize)
+{
+	if (bsize < 512 || bsize > PAGE_SIZE || !is_power_of_2(bsize))
+		return -EINVAL;
+
+	return 0;
+}
+
 static inline bool blk_op_is_passthrough(unsigned int op)
 {
 	op &= REQ_OP_MASK;
@@ -253,8 +261,6 @@
 
 #include <linux/elevator.h>
 
-struct blk_queue_ctx;
-
 struct bio_vec;
 
 enum blk_eh_timer_return {
@@ -1176,7 +1182,8 @@
 
 bool __must_check blk_get_queue(struct request_queue *);
 extern void blk_put_queue(struct request_queue *);
-extern void blk_set_queue_dying(struct request_queue *);
+
+void blk_mark_disk_dead(struct gendisk *disk);
 
 #ifdef CONFIG_BLOCK
 /*
@@ -1198,8 +1205,6 @@
 	bool multiple_queues;
 	bool nowait;
 };
-#define BLK_MAX_REQUEST_COUNT 16
-#define BLK_PLUG_FLUSH_SIZE (128 * 1024)
 
 struct blk_plug_cb;
 typedef void (*blk_plug_cb_fn)(struct blk_plug_cb *, bool);
@@ -1329,11 +1334,12 @@
 enum blk_default_limits {
 	BLK_MAX_SEGMENTS	= 128,
 	BLK_SAFE_MAX_SECTORS	= 255,
-	BLK_DEF_MAX_SECTORS	= 2560,
 	BLK_MAX_SEGMENT_SIZE	= 65536,
 	BLK_SEG_BOUNDARY_MASK	= 0xFFFFFFFFUL,
 };
 
+#define BLK_DEF_MAX_SECTORS 2560u
+
 static inline unsigned long queue_segment_boundary(const struct request_queue *q)
 {
 	return q->limits.seg_boundary_mask;
@@ -1382,6 +1388,17 @@
 	return min(l->max_zone_append_sectors, l->max_sectors);
 }
 
+static inline unsigned int
+bdev_max_zone_append_sectors(struct block_device *bdev)
+{
+	return queue_max_zone_append_sectors(bdev_get_queue(bdev));
+}
+
+static inline unsigned int bdev_max_segments(struct block_device *bdev)
+{
+	return queue_max_segments(bdev_get_queue(bdev));
+}
+
 static inline unsigned queue_logical_block_size(const struct request_queue *q)
 {
 	int retval = 512;
@@ -1412,7 +1429,7 @@
 	return q->limits.io_min;
 }
 
-static inline int bdev_io_min(struct block_device *bdev)
+static inline unsigned int bdev_io_min(struct block_device *bdev)
 {
 	return queue_io_min(bdev_get_queue(bdev));
 }
@@ -1941,6 +1958,7 @@
 void disk_end_io_acct(struct gendisk *disk, unsigned int op,
 		unsigned long start_time);
 
+void bio_start_io_acct_time(struct bio *bio, unsigned long start_time);
 unsigned long bio_start_io_acct(struct bio *bio);
 void bio_end_io_acct_remapped(struct bio *bio, unsigned long start_time,
 		struct block_device *orig_bdev);
@@ -1991,6 +2009,7 @@
 #ifdef CONFIG_BLOCK
 void invalidate_bdev(struct block_device *bdev);
 int sync_blockdev(struct block_device *bdev);
+void sync_bdevs(bool wait);
 #else
 static inline void invalidate_bdev(struct block_device *bdev)
 {
@@ -1999,6 +2018,9 @@
 {
 	return 0;
 }
+static inline void sync_bdevs(bool wait)
+{
+}
 #endif
 int fsync_bdev(struct block_device *bdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bootconfig.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bootconfig.h
@@ -49,7 +49,7 @@
 /* Maximum size of boot config is 32KB - 1 */
 #define XBC_DATA_MAX	(XBC_VALUE - 1)
 
-#define XBC_NODE_MAX	1024
+#define XBC_NODE_MAX	8192
 #define XBC_KEYLEN_MAX	256
 #define XBC_DEPTH_MAX	16
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bootmem_info.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bootmem_info.h
@@ -3,6 +3,7 @@
 #define __LINUX_BOOTMEM_INFO_H
 
 #include <linux/mm.h>
+#include <linux/kmemleak.h>
 
 /*
  * Types for free bootmem stored in page->lru.next. These have to be in
@@ -59,6 +60,7 @@
 
 static inline void free_bootmem_page(struct page *page)
 {
+	kmemleak_free_part(page_to_virt(page), PAGE_SIZE);
 	free_reserved_page(page);
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bpf-cgroup.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bpf-cgroup.h
@@ -517,6 +517,7 @@
 
 #define cgroup_bpf_enabled(atype) (0)
 #define BPF_CGROUP_RUN_SA_PROG_LOCK(sk, uaddr, atype, t_ctx) ({ 0; })
+#define BPF_CGROUP_RUN_SA_PROG(sk, uaddr, atype) ({ 0; })
 #define BPF_CGROUP_PRE_CONNECT_ENABLED(sk) (0)
 #define BPF_CGROUP_RUN_PROG_INET_INGRESS(sk,skb) ({ 0; })
 #define BPF_CGROUP_RUN_PROG_INET_EGRESS(sk,skb) ({ 0; })
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bpf.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bpf.h
@@ -91,7 +91,11 @@
 	/* funcs called by prog_array and perf_event_array map */
 	void *(*map_fd_get_ptr)(struct bpf_map *map, struct file *map_file,
 				int fd);
-	void (*map_fd_put_ptr)(void *ptr);
+	/* If need_defer is true, the implementation should guarantee that
+	 * the to-be-put element is still alive before the bpf program, which
+	 * may manipulate it, exists.
+	 */
+	void (*map_fd_put_ptr)(struct bpf_map *map, void *ptr, bool need_defer);
 	int (*map_gen_lookup)(struct bpf_map *map, struct bpf_insn *insn_buf);
 	u32 (*map_fd_sys_lookup_elem)(void *ptr);
 	void (*map_seq_show_elem)(struct bpf_map *map, void *key,
@@ -188,9 +192,14 @@
 	 */
 	atomic64_t refcnt ____cacheline_aligned;
 	atomic64_t usercnt;
-	struct work_struct work;
+	/* rcu is used before freeing and work is only used during freeing */
+	union {
+		struct work_struct work;
+		struct rcu_head rcu;
+	};
 	struct mutex freeze_mutex;
-	u64 writecnt; /* writable mmap cnt; protected by freeze_mutex */
+	atomic64_t writecnt;
+	bool free_after_mult_rcu_gp;
 };
 
 static inline bool map_value_has_spin_lock(const struct bpf_map *map)
@@ -206,11 +215,9 @@
 static inline void check_and_init_map_value(struct bpf_map *map, void *dst)
 {
 	if (unlikely(map_value_has_spin_lock(map)))
-		*(struct bpf_spin_lock *)(dst + map->spin_lock_off) =
-			(struct bpf_spin_lock){};
+		memset(dst + map->spin_lock_off, 0, sizeof(struct bpf_spin_lock));
 	if (unlikely(map_value_has_timer(map)))
-		*(struct bpf_timer *)(dst + map->timer_off) =
-			(struct bpf_timer){};
+		memset(dst + map->timer_off, 0, sizeof(struct bpf_timer));
 }
 
 /* copy everything but bpf_spin_lock and bpf_timer. There could be one of each. */
@@ -221,7 +228,8 @@
 	if (unlikely(map_value_has_spin_lock(map))) {
 		s_off = map->spin_lock_off;
 		s_sz = sizeof(struct bpf_spin_lock);
-	} else if (unlikely(map_value_has_timer(map))) {
+	}
+	if (unlikely(map_value_has_timer(map))) {
 		t_off = map->timer_off;
 		t_sz = sizeof(struct bpf_timer);
 	}
@@ -294,6 +302,39 @@
 
 extern const struct bpf_map_ops bpf_map_offload_ops;
 
+/* bpf_type_flag contains a set of flags that are applicable to the values of
+ * arg_type, ret_type and reg_type. For example, a pointer value may be null,
+ * or a memory is read-only. We classify types into two categories: base types
+ * and extended types. Extended types are base types combined with a type flag.
+ *
+ * Currently there are no more than 32 base types in arg_type, ret_type and
+ * reg_types.
+ */
+#define BPF_BASE_TYPE_BITS	8
+
+enum bpf_type_flag {
+	/* PTR may be NULL. */
+	PTR_MAYBE_NULL		= BIT(0 + BPF_BASE_TYPE_BITS),
+
+	/* MEM is read-only. When applied on bpf_arg, it indicates the arg is
+	 * compatible with both mutable and immutable memory.
+	 */
+	MEM_RDONLY		= BIT(1 + BPF_BASE_TYPE_BITS),
+
+	/* MEM was "allocated" from a different helper, and cannot be mixed
+	 * with regular non-MEM_ALLOC'ed MEM types.
+	 */
+	MEM_ALLOC		= BIT(2 + BPF_BASE_TYPE_BITS),
+
+	__BPF_TYPE_LAST_FLAG	= MEM_ALLOC,
+};
+
+/* Max number of base types. */
+#define BPF_BASE_TYPE_LIMIT	(1UL << BPF_BASE_TYPE_BITS)
+
+/* Max number of all types. */
+#define BPF_TYPE_LIMIT		(__BPF_TYPE_LAST_FLAG | (__BPF_TYPE_LAST_FLAG - 1))
+
 /* function argument constraints */
 enum bpf_arg_type {
 	ARG_DONTCARE = 0,	/* unused argument in helper function */
@@ -305,13 +346,11 @@
 	ARG_PTR_TO_MAP_KEY,	/* pointer to stack used as map key */
 	ARG_PTR_TO_MAP_VALUE,	/* pointer to stack used as map value */
 	ARG_PTR_TO_UNINIT_MAP_VALUE,	/* pointer to valid memory used to store a map value */
-	ARG_PTR_TO_MAP_VALUE_OR_NULL,	/* pointer to stack used as map value or NULL */
 
 	/* the following constraints used to prototype bpf_memcmp() and other
 	 * functions that access data on eBPF program stack
 	 */
 	ARG_PTR_TO_MEM,		/* pointer to valid memory (stack, packet, map value) */
-	ARG_PTR_TO_MEM_OR_NULL, /* pointer to valid memory or NULL */
 	ARG_PTR_TO_UNINIT_MEM,	/* pointer to memory does not need to be initialized,
 				 * helper function must fill all bytes or clear
 				 * them in error case.
@@ -321,42 +360,65 @@
 	ARG_CONST_SIZE_OR_ZERO,	/* number of bytes accessed from memory or 0 */
 
 	ARG_PTR_TO_CTX,		/* pointer to context */
-	ARG_PTR_TO_CTX_OR_NULL,	/* pointer to context or NULL */
 	ARG_ANYTHING,		/* any (initialized) argument is ok */
 	ARG_PTR_TO_SPIN_LOCK,	/* pointer to bpf_spin_lock */
 	ARG_PTR_TO_SOCK_COMMON,	/* pointer to sock_common */
 	ARG_PTR_TO_INT,		/* pointer to int */
 	ARG_PTR_TO_LONG,	/* pointer to long */
 	ARG_PTR_TO_SOCKET,	/* pointer to bpf_sock (fullsock) */
-	ARG_PTR_TO_SOCKET_OR_NULL,	/* pointer to bpf_sock (fullsock) or NULL */
 	ARG_PTR_TO_BTF_ID,	/* pointer to in-kernel struct */
 	ARG_PTR_TO_ALLOC_MEM,	/* pointer to dynamically allocated memory */
-	ARG_PTR_TO_ALLOC_MEM_OR_NULL,	/* pointer to dynamically allocated memory or NULL */
 	ARG_CONST_ALLOC_SIZE_OR_ZERO,	/* number of allocated bytes requested */
 	ARG_PTR_TO_BTF_ID_SOCK_COMMON,	/* pointer to in-kernel sock_common or bpf-mirrored bpf_sock */
 	ARG_PTR_TO_PERCPU_BTF_ID,	/* pointer to in-kernel percpu type */
 	ARG_PTR_TO_FUNC,	/* pointer to a bpf program function */
-	ARG_PTR_TO_STACK_OR_NULL,	/* pointer to stack or NULL */
+	ARG_PTR_TO_STACK,	/* pointer to stack */
 	ARG_PTR_TO_CONST_STR,	/* pointer to a null terminated read-only string */
 	ARG_PTR_TO_TIMER,	/* pointer to bpf_timer */
 	__BPF_ARG_TYPE_MAX,
+
+	/* Extended arg_types. */
+	ARG_PTR_TO_MAP_VALUE_OR_NULL	= PTR_MAYBE_NULL | ARG_PTR_TO_MAP_VALUE,
+	ARG_PTR_TO_MEM_OR_NULL		= PTR_MAYBE_NULL | ARG_PTR_TO_MEM,
+	ARG_PTR_TO_CTX_OR_NULL		= PTR_MAYBE_NULL | ARG_PTR_TO_CTX,
+	ARG_PTR_TO_SOCKET_OR_NULL	= PTR_MAYBE_NULL | ARG_PTR_TO_SOCKET,
+	ARG_PTR_TO_ALLOC_MEM_OR_NULL	= PTR_MAYBE_NULL | ARG_PTR_TO_ALLOC_MEM,
+	ARG_PTR_TO_STACK_OR_NULL	= PTR_MAYBE_NULL | ARG_PTR_TO_STACK,
+
+	/* This must be the last entry. Its purpose is to ensure the enum is
+	 * wide enough to hold the higher bits reserved for bpf_type_flag.
+	 */
+	__BPF_ARG_TYPE_LIMIT	= BPF_TYPE_LIMIT,
 };
+static_assert(__BPF_ARG_TYPE_MAX <= BPF_BASE_TYPE_LIMIT);
 
 /* type of values returned from helper functions */
 enum bpf_return_type {
 	RET_INTEGER,			/* function returns integer */
 	RET_VOID,			/* function doesn't return anything */
 	RET_PTR_TO_MAP_VALUE,		/* returns a pointer to map elem value */
-	RET_PTR_TO_MAP_VALUE_OR_NULL,	/* returns a pointer to map elem value or NULL */
-	RET_PTR_TO_SOCKET_OR_NULL,	/* returns a pointer to a socket or NULL */
-	RET_PTR_TO_TCP_SOCK_OR_NULL,	/* returns a pointer to a tcp_sock or NULL */
-	RET_PTR_TO_SOCK_COMMON_OR_NULL,	/* returns a pointer to a sock_common or NULL */
-	RET_PTR_TO_ALLOC_MEM_OR_NULL,	/* returns a pointer to dynamically allocated memory or NULL */
-	RET_PTR_TO_BTF_ID_OR_NULL,	/* returns a pointer to a btf_id or NULL */
-	RET_PTR_TO_MEM_OR_BTF_ID_OR_NULL, /* returns a pointer to a valid memory or a btf_id or NULL */
+	RET_PTR_TO_SOCKET,		/* returns a pointer to a socket */
+	RET_PTR_TO_TCP_SOCK,		/* returns a pointer to a tcp_sock */
+	RET_PTR_TO_SOCK_COMMON,		/* returns a pointer to a sock_common */
+	RET_PTR_TO_ALLOC_MEM,		/* returns a pointer to dynamically allocated memory */
 	RET_PTR_TO_MEM_OR_BTF_ID,	/* returns a pointer to a valid memory or a btf_id */
 	RET_PTR_TO_BTF_ID,		/* returns a pointer to a btf_id */
+	__BPF_RET_TYPE_MAX,
+
+	/* Extended ret_types. */
+	RET_PTR_TO_MAP_VALUE_OR_NULL	= PTR_MAYBE_NULL | RET_PTR_TO_MAP_VALUE,
+	RET_PTR_TO_SOCKET_OR_NULL	= PTR_MAYBE_NULL | RET_PTR_TO_SOCKET,
+	RET_PTR_TO_TCP_SOCK_OR_NULL	= PTR_MAYBE_NULL | RET_PTR_TO_TCP_SOCK,
+	RET_PTR_TO_SOCK_COMMON_OR_NULL	= PTR_MAYBE_NULL | RET_PTR_TO_SOCK_COMMON,
+	RET_PTR_TO_ALLOC_MEM_OR_NULL	= PTR_MAYBE_NULL | MEM_ALLOC | RET_PTR_TO_ALLOC_MEM,
+	RET_PTR_TO_BTF_ID_OR_NULL	= PTR_MAYBE_NULL | RET_PTR_TO_BTF_ID,
+
+	/* This must be the last entry. Its purpose is to ensure the enum is
+	 * wide enough to hold the higher bits reserved for bpf_type_flag.
+	 */
+	__BPF_RET_TYPE_LIMIT	= BPF_TYPE_LIMIT,
 };
+static_assert(__BPF_RET_TYPE_MAX <= BPF_BASE_TYPE_LIMIT);
 
 /* eBPF function prototype used by verifier to allow BPF_CALLs from eBPF programs
  * to in-kernel helper functions and for adjusting imm32 field in BPF_CALL
@@ -418,18 +480,15 @@
 	PTR_TO_CTX,		 /* reg points to bpf_context */
 	CONST_PTR_TO_MAP,	 /* reg points to struct bpf_map */
 	PTR_TO_MAP_VALUE,	 /* reg points to map element value */
-	PTR_TO_MAP_VALUE_OR_NULL,/* points to map elem value or NULL */
+	PTR_TO_MAP_KEY,		 /* reg points to a map element key */
 	PTR_TO_STACK,		 /* reg == frame_pointer + offset */
 	PTR_TO_PACKET_META,	 /* skb->data - meta_len */
 	PTR_TO_PACKET,		 /* reg points to skb->data */
 	PTR_TO_PACKET_END,	 /* skb->data + headlen */
 	PTR_TO_FLOW_KEYS,	 /* reg points to bpf_flow_keys */
 	PTR_TO_SOCKET,		 /* reg points to struct bpf_sock */
-	PTR_TO_SOCKET_OR_NULL,	 /* reg points to struct bpf_sock or NULL */
 	PTR_TO_SOCK_COMMON,	 /* reg points to sock_common */
-	PTR_TO_SOCK_COMMON_OR_NULL, /* reg points to sock_common or NULL */
 	PTR_TO_TCP_SOCK,	 /* reg points to struct tcp_sock */
-	PTR_TO_TCP_SOCK_OR_NULL, /* reg points to struct tcp_sock or NULL */
 	PTR_TO_TP_BUFFER,	 /* reg points to a writable raw tp's buffer */
 	PTR_TO_XDP_SOCK,	 /* reg points to struct xdp_sock */
 	/* PTR_TO_BTF_ID points to a kernel struct that does not need
@@ -447,18 +506,25 @@
 	 * been checked for null. Used primarily to inform the verifier
 	 * an explicit null check is required for this struct.
 	 */
-	PTR_TO_BTF_ID_OR_NULL,
 	PTR_TO_MEM,		 /* reg points to valid memory region */
-	PTR_TO_MEM_OR_NULL,	 /* reg points to valid memory region or NULL */
-	PTR_TO_RDONLY_BUF,	 /* reg points to a readonly buffer */
-	PTR_TO_RDONLY_BUF_OR_NULL, /* reg points to a readonly buffer or NULL */
-	PTR_TO_RDWR_BUF,	 /* reg points to a read/write buffer */
-	PTR_TO_RDWR_BUF_OR_NULL, /* reg points to a read/write buffer or NULL */
+	PTR_TO_BUF,		 /* reg points to a read/write buffer */
 	PTR_TO_PERCPU_BTF_ID,	 /* reg points to a percpu kernel variable */
 	PTR_TO_FUNC,		 /* reg points to a bpf program function */
-	PTR_TO_MAP_KEY,		 /* reg points to a map element key */
 	__BPF_REG_TYPE_MAX,
+
+	/* Extended reg_types. */
+	PTR_TO_MAP_VALUE_OR_NULL	= PTR_MAYBE_NULL | PTR_TO_MAP_VALUE,
+	PTR_TO_SOCKET_OR_NULL		= PTR_MAYBE_NULL | PTR_TO_SOCKET,
+	PTR_TO_SOCK_COMMON_OR_NULL	= PTR_MAYBE_NULL | PTR_TO_SOCK_COMMON,
+	PTR_TO_TCP_SOCK_OR_NULL		= PTR_MAYBE_NULL | PTR_TO_TCP_SOCK,
+	PTR_TO_BTF_ID_OR_NULL		= PTR_MAYBE_NULL | PTR_TO_BTF_ID,
+
+	/* This must be the last entry. Its purpose is to ensure the enum is
+	 * wide enough to hold the higher bits reserved for bpf_type_flag.
+	 */
+	__BPF_REG_TYPE_LIMIT	= BPF_TYPE_LIMIT,
 };
+static_assert(__BPF_REG_TYPE_MAX <= BPF_BASE_TYPE_LIMIT);
 
 /* The information passed from prog-specific *_is_valid_access
  * back to the verifier.
@@ -481,6 +547,12 @@
 	aux->ctx_field_size = size;
 }
 
+static inline bool bpf_pseudo_func(const struct bpf_insn *insn)
+{
+	return insn->code == (BPF_LD | BPF_IMM | BPF_DW) &&
+	       insn->src_reg == BPF_PSEUDO_FUNC;
+}
+
 struct bpf_prog_ops {
 	int (*test_run)(struct bpf_prog *prog, const union bpf_attr *kattr,
 			union bpf_attr __user *uattr);
@@ -723,6 +795,7 @@
 struct bpf_trampoline *bpf_trampoline_get(u64 key,
 					  struct bpf_attach_target_info *tgt_info);
 void bpf_trampoline_put(struct bpf_trampoline *tr);
+int arch_prepare_bpf_dispatcher(void *image, s64 *funcs, int num_funcs);
 #define BPF_DISPATCHER_INIT(_name) {				\
 	.mutex = __MUTEX_INITIALIZER(_name.mutex),		\
 	.func = &_name##_func,					\
@@ -781,7 +854,7 @@
 static inline struct bpf_trampoline *bpf_trampoline_get(u64 key,
 							struct bpf_attach_target_info *tgt_info)
 {
-	return ERR_PTR(-EOPNOTSUPP);
+	return NULL;
 }
 static inline void bpf_trampoline_put(struct bpf_trampoline *tr) {}
 #define DEFINE_BPF_DISPATCHER(name)
@@ -1320,28 +1393,16 @@
  * kprobes, tracepoints) to prevent deadlocks on map operations as any of
  * these events can happen inside a region which holds a map bucket lock
  * and can deadlock on it.
- *
- * Use the preemption safe inc/dec variants on RT because migrate disable
- * is preemptible on RT and preemption in the middle of the RMW operation
- * might lead to inconsistent state. Use the raw variants for non RT
- * kernels as migrate_disable() maps to preempt_disable() so the slightly
- * more expensive save operation can be avoided.
  */
 static inline void bpf_disable_instrumentation(void)
 {
 	migrate_disable();
-	if (IS_ENABLED(CONFIG_PREEMPT_RT))
-		this_cpu_inc(bpf_prog_active);
-	else
-		__this_cpu_inc(bpf_prog_active);
+	this_cpu_inc(bpf_prog_active);
 }
 
 static inline void bpf_enable_instrumentation(void)
 {
-	if (IS_ENABLED(CONFIG_PREEMPT_RT))
-		this_cpu_dec(bpf_prog_active);
-	else
-		__this_cpu_dec(bpf_prog_active);
+	this_cpu_dec(bpf_prog_active);
 	migrate_enable();
 }
 
@@ -1387,6 +1448,7 @@
 void *bpf_map_area_alloc(u64 size, int numa_node);
 void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
 void bpf_map_area_free(void *base);
+bool bpf_map_write_active(const struct bpf_map *map);
 void bpf_map_init_from_attr(struct bpf_map *map, union bpf_attr *attr);
 int  generic_map_lookup_batch(struct bpf_map *map,
 			      const union bpf_attr *attr,
@@ -1589,17 +1651,17 @@
 struct btf *bpf_get_btf_vmlinux(void);
 
 /* Map specifics */
-struct xdp_buff;
+struct xdp_frame;
 struct sk_buff;
 struct bpf_dtab_netdev;
 struct bpf_cpu_map_entry;
 
 void __dev_flush(void);
-int dev_xdp_enqueue(struct net_device *dev, struct xdp_buff *xdp,
+int dev_xdp_enqueue(struct net_device *dev, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx);
-int dev_map_enqueue(struct bpf_dtab_netdev *dst, struct xdp_buff *xdp,
+int dev_map_enqueue(struct bpf_dtab_netdev *dst, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx);
-int dev_map_enqueue_multi(struct xdp_buff *xdp, struct net_device *dev_rx,
+int dev_map_enqueue_multi(struct xdp_frame *xdpf, struct net_device *dev_rx,
 			  struct bpf_map *map, bool exclude_ingress);
 int dev_map_generic_redirect(struct bpf_dtab_netdev *dst, struct sk_buff *skb,
 			     struct bpf_prog *xdp_prog);
@@ -1608,7 +1670,7 @@
 			   bool exclude_ingress);
 
 void __cpu_map_flush(void);
-int cpu_map_enqueue(struct bpf_cpu_map_entry *rcpu, struct xdp_buff *xdp,
+int cpu_map_enqueue(struct bpf_cpu_map_entry *rcpu, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx);
 int cpu_map_generic_redirect(struct bpf_cpu_map_entry *rcpu,
 			     struct sk_buff *skb);
@@ -1677,6 +1739,12 @@
 const struct btf_func_model *
 bpf_jit_find_kfunc_model(const struct bpf_prog *prog,
 			 const struct bpf_insn *insn);
+
+static inline bool unprivileged_ebpf_enabled(void)
+{
+	return !sysctl_unprivileged_bpf_disabled;
+}
+
 #else /* !CONFIG_BPF_SYSCALL */
 static inline struct bpf_prog *bpf_prog_get(u32 ufd)
 {
@@ -1755,26 +1823,26 @@
 {
 }
 
-struct xdp_buff;
+struct xdp_frame;
 struct bpf_dtab_netdev;
 struct bpf_cpu_map_entry;
 
 static inline
-int dev_xdp_enqueue(struct net_device *dev, struct xdp_buff *xdp,
+int dev_xdp_enqueue(struct net_device *dev, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx)
 {
 	return 0;
 }
 
 static inline
-int dev_map_enqueue(struct bpf_dtab_netdev *dst, struct xdp_buff *xdp,
+int dev_map_enqueue(struct bpf_dtab_netdev *dst, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx)
 {
 	return 0;
 }
 
 static inline
-int dev_map_enqueue_multi(struct xdp_buff *xdp, struct net_device *dev_rx,
+int dev_map_enqueue_multi(struct xdp_frame *xdpf, struct net_device *dev_rx,
 			  struct bpf_map *map, bool exclude_ingress)
 {
 	return 0;
@@ -1802,7 +1870,7 @@
 }
 
 static inline int cpu_map_enqueue(struct bpf_cpu_map_entry *rcpu,
-				  struct xdp_buff *xdp,
+				  struct xdp_frame *xdpf,
 				  struct net_device *dev_rx)
 {
 	return 0;
@@ -1895,6 +1963,12 @@
 {
 	return NULL;
 }
+
+static inline bool unprivileged_ebpf_enabled(void)
+{
+	return false;
+}
+
 #endif /* CONFIG_BPF_SYSCALL */
 
 void __bpf_free_used_btfs(struct bpf_prog_aux *aux,
@@ -1937,6 +2011,8 @@
 				       struct net_device *netdev);
 bool bpf_offload_dev_match(struct bpf_prog *prog, struct net_device *netdev);
 
+void unpriv_ebpf_notify(int new_state);
+
 #if defined(CONFIG_NET) && defined(CONFIG_BPF_SYSCALL)
 int bpf_prog_offload_init(struct bpf_prog *prog, union bpf_attr *attr);
 
@@ -1960,6 +2036,7 @@
 int sock_map_prog_detach(const union bpf_attr *attr, enum bpf_prog_type ptype);
 int sock_map_update_elem_sys(struct bpf_map *map, void *key, void *value, u64 flags);
 void sock_map_unhash(struct sock *sk);
+void sock_map_destroy(struct sock *sk);
 void sock_map_close(struct sock *sk, long timeout);
 #else
 static inline int bpf_prog_offload_init(struct bpf_prog *prog,
@@ -2217,11 +2294,24 @@
 int bpf_arch_text_poke(void *ip, enum bpf_text_poke_type t,
 		       void *addr1, void *addr2);
 
+void bpf_arch_poke_desc_update(struct bpf_jit_poke_descriptor *poke,
+			       struct bpf_prog *new, struct bpf_prog *old);
+
 struct btf_id_set;
 bool btf_id_set_contains(const struct btf_id_set *set, u32 id);
 
+#define MAX_BPRINTF_VARARGS		12
+#define MAX_BPRINTF_BUF			1024
+
+struct bpf_bprintf_data {
+	u32 *bin_args;
+	char *buf;
+	bool get_bin_args;
+	bool get_buf;
+};
+
 int bpf_bprintf_prepare(char *fmt, u32 fmt_size, const u64 *raw_args,
-			u32 **bin_buf, u32 num_args);
-void bpf_bprintf_cleanup(void);
+			u32 num_args, struct bpf_bprintf_data *data);
+void bpf_bprintf_cleanup(struct bpf_bprintf_data *data);
 
 #endif /* _LINUX_BPF_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bpf_verifier.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bpf_verifier.h
@@ -18,6 +18,8 @@
  * that converting umax_value to int cannot overflow.
  */
 #define BPF_MAX_VAR_SIZ	(1 << 29)
+/* size of type_str_buf in bpf_verifier. */
+#define TYPE_STR_BUF_LEN 64
 
 /* Liveness marks, used for registers and spilled-regs (in stack slots).
  * Read marks propagate upwards until they find a write mark; they record that
@@ -190,6 +192,17 @@
 	 * is used purely to inform the user of a reference leak.
 	 */
 	int insn_idx;
+	/* There can be a case like:
+	 * main (frame 0)
+	 *  cb (frame 1)
+	 *   func (frame 3)
+	 *    cb (frame 4)
+	 * Hence for frame 4, if callback_ref just stored boolean, it would be
+	 * impossible to distinguish nested callback refs. Hence store the
+	 * frameno and compare that to callback_ref in check_reference_leak when
+	 * exiting a callback function.
+	 */
+	int callback_ref;
 };
 
 /* state of the program:
@@ -315,6 +328,27 @@
 	     iter < frame->allocated_stack / BPF_REG_SIZE;		\
 	     iter++, reg = bpf_get_spilled_reg(iter, frame))
 
+/* Invoke __expr over regsiters in __vst, setting __state and __reg */
+#define bpf_for_each_reg_in_vstate(__vst, __state, __reg, __expr)   \
+	({                                                               \
+		struct bpf_verifier_state *___vstate = __vst;            \
+		int ___i, ___j;                                          \
+		for (___i = 0; ___i <= ___vstate->curframe; ___i++) {    \
+			struct bpf_reg_state *___regs;                   \
+			__state = ___vstate->frame[___i];                \
+			___regs = __state->regs;                         \
+			for (___j = 0; ___j < MAX_BPF_REG; ___j++) {     \
+				__reg = &___regs[___j];                  \
+				(void)(__expr);                          \
+			}                                                \
+			bpf_for_each_spilled_reg(___j, __state, __reg) { \
+				if (!__reg)                              \
+					continue;                        \
+				(void)(__expr);                          \
+			}                                                \
+		}                                                        \
+	})
+
 /* linked list of verifier states used to prune search */
 struct bpf_verifier_state_list {
 	struct bpf_verifier_state state;
@@ -396,6 +430,13 @@
 		 log->level == BPF_LOG_KERNEL);
 }
 
+static inline bool
+bpf_verifier_log_attr_valid(const struct bpf_verifier_log *log)
+{
+	return log->len_total >= 128 && log->len_total <= UINT_MAX >> 2 &&
+	       log->level && log->ubuf && !(log->level & ~BPF_LOG_MASK);
+}
+
 #define BPF_MAX_SUBPROGS 256
 
 struct bpf_subprog_info {
@@ -467,6 +508,8 @@
 	/* longest register parentage chain walked for liveness marking */
 	u32 longest_mark_read_walk;
 	bpfptr_t fd_array;
+	/* buffer used in reg_type_str() to generate reg_type string */
+	char type_str_buf[TYPE_STR_BUF_LEN];
 };
 
 __printf(2, 0) void bpf_verifier_vlog(struct bpf_verifier_log *log,
@@ -498,8 +541,8 @@
 void
 bpf_prog_offload_remove_insns(struct bpf_verifier_env *env, u32 off, u32 cnt);
 
-int check_ctx_reg(struct bpf_verifier_env *env,
-		  const struct bpf_reg_state *reg, int regno);
+int check_ptr_off_reg(struct bpf_verifier_env *env,
+		      const struct bpf_reg_state *reg, int regno);
 int check_mem_reg(struct bpf_verifier_env *env, struct bpf_reg_state *reg,
 		   u32 regno, u32 mem_size);
 
@@ -528,4 +571,18 @@
 			    u32 btf_id,
 			    struct bpf_attach_target_info *tgt_info);
 
+#define BPF_BASE_TYPE_MASK	GENMASK(BPF_BASE_TYPE_BITS - 1, 0)
+
+/* extract base type from bpf_{arg, return, reg}_type. */
+static inline u32 base_type(u32 type)
+{
+	return type & BPF_BASE_TYPE_MASK;
+}
+
+/* extract flags from an extended type. See bpf_type_flag in bpf.h. */
+static inline u32 type_flag(u32 type)
+{
+	return type & ~BPF_BASE_TYPE_MASK;
+}
+
 #endif /* _LINUX_BPF_VERIFIER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/bpfptr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/bpfptr.h
@@ -48,7 +48,9 @@
 static inline int copy_from_bpfptr_offset(void *dst, bpfptr_t src,
 					  size_t offset, size_t size)
 {
-	return copy_from_sockptr_offset(dst, (sockptr_t) src, offset, size);
+	if (!bpfptr_is_kernel(src))
+		return copy_from_user(dst, src.user + offset, size);
+	return copy_from_kernel_nofault(dst, src.kernel + offset, size);
 }
 
 static inline int copy_from_bpfptr(void *dst, bpfptr_t src, size_t size)
@@ -77,7 +79,9 @@
 
 static inline long strncpy_from_bpfptr(char *dst, bpfptr_t src, size_t count)
 {
-	return strncpy_from_sockptr(dst, (sockptr_t) src, count);
+	if (bpfptr_is_kernel(src))
+		return strncpy_from_kernel_nofault(dst, src.kernel, count);
+	return strncpy_from_user(dst, src.user, count);
 }
 
 #endif /* _LINUX_BPFPTR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/btf_ids.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/btf_ids.h
@@ -38,7 +38,7 @@
 	____BTF_ID(symbol)
 
 #define __ID(prefix) \
-	__PASTE(prefix, __COUNTER__)
+	__PASTE(__PASTE(prefix, __COUNTER__), __LINE__)
 
 /*
  * The BTF_ID defines unique symbol for each ID pointing
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/buffer_head.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/buffer_head.h
@@ -117,7 +117,6 @@
  * of the form "mark_buffer_foo()".  These are higher-level functions which
  * do something in addition to setting a b_state bit.
  */
-BUFFER_FNS(Uptodate, uptodate)
 BUFFER_FNS(Dirty, dirty)
 TAS_BUFFER_FNS(Dirty, dirty)
 BUFFER_FNS(Lock, locked)
@@ -135,6 +134,41 @@
 BUFFER_FNS(Prio, prio)
 BUFFER_FNS(Defer_Completion, defer_completion)
 
+static __always_inline void set_buffer_uptodate(struct buffer_head *bh)
+{
+	/*
+	 * If somebody else already set this uptodate, they will
+	 * have done the memory barrier, and a reader will thus
+	 * see *some* valid buffer state.
+	 *
+	 * Any other serialization (with IO errors or whatever that
+	 * might clear the bit) has to come from other state (eg BH_Lock).
+	 */
+	if (test_bit(BH_Uptodate, &bh->b_state))
+		return;
+
+	/*
+	 * make it consistent with folio_mark_uptodate
+	 * pairs with smp_load_acquire in buffer_uptodate
+	 */
+	smp_mb__before_atomic();
+	set_bit(BH_Uptodate, &bh->b_state);
+}
+
+static __always_inline void clear_buffer_uptodate(struct buffer_head *bh)
+{
+	clear_bit(BH_Uptodate, &bh->b_state);
+}
+
+static __always_inline int buffer_uptodate(const struct buffer_head *bh)
+{
+	/*
+	 * make it consistent with folio_test_uptodate
+	 * pairs with smp_mb__before_atomic in set_buffer_uptodate
+	 */
+	return (smp_load_acquire(&bh->b_state) & (1UL << BH_Uptodate)) != 0;
+}
+
 #define bh_offset(bh)		((unsigned long)(bh)->b_data & ~PAGE_MASK)
 
 /* If we *know* page->private refers to buffer_heads */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/can/length.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/can/length.h
@@ -69,17 +69,18 @@
  * Error Status Indicator (ESI)		1
  * Data length code (DLC)		4
  * Data field				0...512
- * Stuff Bit Count (SBC)		0...16: 4 20...64:5
+ * Stuff Bit Count (SBC)		4
  * CRC					0...16: 17 20...64:21
  * CRC delimiter (CD)			1
+ * Fixed Stuff bits (FSB)		0...16: 6 20...64:7
  * ACK slot (AS)			1
  * ACK delimiter (AD)			1
  * End-of-frame (EOF)			7
  * Inter frame spacing			3
  *
- * assuming CRC21, rounded up and ignoring bitstuffing
+ * assuming CRC21, rounded up and ignoring dynamic bitstuffing
  */
-#define CANFD_FRAME_OVERHEAD_SFF DIV_ROUND_UP(61, 8)
+#define CANFD_FRAME_OVERHEAD_SFF DIV_ROUND_UP(67, 8)
 
 /*
  * Size of a CAN-FD Extended Frame
@@ -98,17 +99,18 @@
  * Error Status Indicator (ESI)		1
  * Data length code (DLC)		4
  * Data field				0...512
- * Stuff Bit Count (SBC)		0...16: 4 20...64:5
+ * Stuff Bit Count (SBC)		4
  * CRC					0...16: 17 20...64:21
  * CRC delimiter (CD)			1
+ * Fixed Stuff bits (FSB)		0...16: 6 20...64:7
  * ACK slot (AS)			1
  * ACK delimiter (AD)			1
  * End-of-frame (EOF)			7
  * Inter frame spacing			3
  *
- * assuming CRC21, rounded up and ignoring bitstuffing
+ * assuming CRC21, rounded up and ignoring dynamic bitstuffing
  */
-#define CANFD_FRAME_OVERHEAD_EFF DIV_ROUND_UP(80, 8)
+#define CANFD_FRAME_OVERHEAD_EFF DIV_ROUND_UP(86, 8)
 
 /*
  * Maximum size of a Classical CAN frame
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/can/platform/sja1000.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/can/platform/sja1000.h
@@ -14,7 +14,7 @@
 #define OCR_MODE_TEST     0x01
 #define OCR_MODE_NORMAL   0x02
 #define OCR_MODE_CLOCK    0x03
-#define OCR_MODE_MASK     0x07
+#define OCR_MODE_MASK     0x03
 #define OCR_TX0_INVERT    0x04
 #define OCR_TX0_PULLDOWN  0x08
 #define OCR_TX0_PULLUP    0x10
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cc_platform.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cc_platform.h
@@ -0,0 +1,88 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Confidential Computing Platform Capability checks
+ *
+ * Copyright (C) 2021 Advanced Micro Devices, Inc.
+ *
+ * Author: Tom Lendacky <thomas.lendacky@amd.com>
+ */
+
+#ifndef _LINUX_CC_PLATFORM_H
+#define _LINUX_CC_PLATFORM_H
+
+#include <linux/types.h>
+#include <linux/stddef.h>
+
+/**
+ * enum cc_attr - Confidential computing attributes
+ *
+ * These attributes represent confidential computing features that are
+ * currently active.
+ */
+enum cc_attr {
+	/**
+	 * @CC_ATTR_MEM_ENCRYPT: Memory encryption is active
+	 *
+	 * The platform/OS is running with active memory encryption. This
+	 * includes running either as a bare-metal system or a hypervisor
+	 * and actively using memory encryption or as a guest/virtual machine
+	 * and actively using memory encryption.
+	 *
+	 * Examples include SME, SEV and SEV-ES.
+	 */
+	CC_ATTR_MEM_ENCRYPT,
+
+	/**
+	 * @CC_ATTR_HOST_MEM_ENCRYPT: Host memory encryption is active
+	 *
+	 * The platform/OS is running as a bare-metal system or a hypervisor
+	 * and actively using memory encryption.
+	 *
+	 * Examples include SME.
+	 */
+	CC_ATTR_HOST_MEM_ENCRYPT,
+
+	/**
+	 * @CC_ATTR_GUEST_MEM_ENCRYPT: Guest memory encryption is active
+	 *
+	 * The platform/OS is running as a guest/virtual machine and actively
+	 * using memory encryption.
+	 *
+	 * Examples include SEV and SEV-ES.
+	 */
+	CC_ATTR_GUEST_MEM_ENCRYPT,
+
+	/**
+	 * @CC_ATTR_GUEST_STATE_ENCRYPT: Guest state encryption is active
+	 *
+	 * The platform/OS is running as a guest/virtual machine and actively
+	 * using memory encryption and register state encryption.
+	 *
+	 * Examples include SEV-ES.
+	 */
+	CC_ATTR_GUEST_STATE_ENCRYPT,
+};
+
+#ifdef CONFIG_ARCH_HAS_CC_PLATFORM
+
+/**
+ * cc_platform_has() - Checks if the specified cc_attr attribute is active
+ * @attr: Confidential computing attribute to check
+ *
+ * The cc_platform_has() function will return an indicator as to whether the
+ * specified Confidential Computing attribute is currently active.
+ *
+ * Context: Any context
+ * Return:
+ * * TRUE  - Specified Confidential Computing attribute is active
+ * * FALSE - Specified Confidential Computing attribute is not active
+ */
+bool cc_platform_has(enum cc_attr attr);
+
+#else	/* !CONFIG_ARCH_HAS_CC_PLATFORM */
+
+static inline bool cc_platform_has(enum cc_attr attr) { return false; }
+
+#endif	/* CONFIG_ARCH_HAS_CC_PLATFORM */
+
+#endif	/* _LINUX_CC_PLATFORM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ceph/osd_client.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ceph/osd_client.h
@@ -287,6 +287,9 @@
 	rados_watcherrcb_t errcb;
 	void *data;
 
+	struct ceph_pagelist *request_pl;
+	struct page **notify_id_pages;
+
 	struct page ***preply_pages;
 	size_t *preply_len;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cgroup-defs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cgroup-defs.h
@@ -71,9 +71,6 @@
 
 	/* Cgroup is frozen. */
 	CGRP_FROZEN,
-
-	/* Control group has to be killed. */
-	CGRP_KILL,
 };
 
 /* cgroup_root->flags */
@@ -264,7 +261,8 @@
 	 * List of csets participating in the on-going migration either as
 	 * source or destination.  Protected by cgroup_mutex.
 	 */
-	struct list_head mg_preload_node;
+	struct list_head mg_src_preload_node;
+	struct list_head mg_dst_preload_node;
 	struct list_head mg_node;
 
 	/*
@@ -406,6 +404,9 @@
 
 	int nr_threaded_children;	/* # of live threaded child cgroups */
 
+	/* sequence number for cgroup.kill, serialized by css_set_lock. */
+	unsigned int kill_seq;
+
 	struct kernfs_node *kn;		/* cgroup kernfs entry */
 	struct cgroup_file procs_file;	/* handle for "cgroup.procs" */
 	struct cgroup_file events_file;	/* handle for "cgroup.events" */
@@ -504,6 +505,10 @@
 	/* Unique id for this hierarchy. */
 	int hierarchy_id;
 
+	/* A list running through the active hierarchies */
+	struct list_head root_list;
+	struct rcu_head rcu;	/* Must be near the top */
+
 	/* The root cgroup.  Root is destroyed on its release. */
 	struct cgroup cgrp;
 
@@ -513,9 +518,6 @@
 	/* Number of cgroups in the hierarchy, used only for /proc/cgroups */
 	atomic_t nr_cgrps;
 
-	/* A list running through the active hierarchies */
-	struct list_head root_list;
-
 	/* Hierarchy-specific flags */
 	unsigned int flags;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cgroup.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cgroup.h
@@ -68,6 +68,7 @@
 	struct list_head		iters_node;	/* css_set->task_iters */
 };
 
+extern struct file_system_type cgroup_fs_type;
 extern struct cgroup_root cgrp_dfl_root;
 extern struct css_set init_css_set;
 
@@ -450,6 +451,7 @@
 extern spinlock_t css_set_lock;
 #define task_css_set_check(task, __c)					\
 	rcu_dereference_check((task)->cgroups,				\
+		rcu_read_lock_sched_held() ||				\
 		lockdep_is_held(&cgroup_mutex) ||			\
 		lockdep_is_held(&css_set_lock) ||			\
 		((task)->flags & PF_EXITING) || (__c))
@@ -751,11 +753,6 @@
 
 static inline void cgroup_path_from_kernfs_id(u64 id, char *buf, size_t buflen)
 {}
-
-static inline struct cgroup *cgroup_get_from_id(u64 id)
-{
-	return NULL;
-}
 #endif /* !CONFIG_CGROUPS */
 
 #ifdef CONFIG_CGROUPS
@@ -791,11 +788,9 @@
 
 	cpuacct_charge(task, delta_exec);
 
-	rcu_read_lock();
 	cgrp = task_dfl_cgroup(task);
 	if (cgroup_parent(cgrp))
 		__cgroup_account_cputime(cgrp, delta_exec);
-	rcu_read_unlock();
 }
 
 static inline void cgroup_account_cputime_field(struct task_struct *task,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/clk-provider.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/clk-provider.h
@@ -61,7 +61,7 @@
 };
 
 /**
- * struct clk_duty - Struture encoding the duty cycle ratio of a clock
+ * struct clk_duty - Structure encoding the duty cycle ratio of a clock
  *
  * @num:	Numerator of the duty cycle ratio
  * @den:	Denominator of the duty cycle ratio
@@ -116,7 +116,7 @@
  * @restore_context: Restore the context of the clock after a restoration
  *		of power.
  *
- * @recalc_rate	Recalculate the rate of this clock, by querying hardware. The
+ * @recalc_rate: Recalculate the rate of this clock, by querying hardware. The
  *		parent rate is an input parameter.  It is up to the caller to
  *		ensure that the prepare_mutex is held across this call.
  *		Returns the calculated rate.  Optional, but recommended - if
@@ -350,7 +350,7 @@
 		const char *parent_name, const struct clk_hw *parent_hw,
 		const struct clk_parent_data *parent_data, unsigned long flags,
 		unsigned long fixed_rate, unsigned long fixed_accuracy,
-		unsigned long clk_fixed_flags);
+		unsigned long clk_fixed_flags, bool devm);
 struct clk *clk_register_fixed_rate(struct device *dev, const char *name,
 		const char *parent_name, unsigned long flags,
 		unsigned long fixed_rate);
@@ -365,7 +365,20 @@
  */
 #define clk_hw_register_fixed_rate(dev, name, parent_name, flags, fixed_rate)  \
 	__clk_hw_register_fixed_rate((dev), NULL, (name), (parent_name), NULL, \
-				     NULL, (flags), (fixed_rate), 0, 0)
+				     NULL, (flags), (fixed_rate), 0, 0, false)
+
+/**
+ * devm_clk_hw_register_fixed_rate - register fixed-rate clock with the clock
+ * framework
+ * @dev: device that is registering this clock
+ * @name: name of this clock
+ * @parent_name: name of clock's parent
+ * @flags: framework-specific flags
+ * @fixed_rate: non-adjustable clock rate
+ */
+#define devm_clk_hw_register_fixed_rate(dev, name, parent_name, flags, fixed_rate)  \
+	__clk_hw_register_fixed_rate((dev), NULL, (name), (parent_name), NULL, \
+				     NULL, (flags), (fixed_rate), 0, 0, true)
 /**
  * clk_hw_register_fixed_rate_parent_hw - register fixed-rate clock with
  * the clock framework
@@ -378,7 +391,7 @@
 #define clk_hw_register_fixed_rate_parent_hw(dev, name, parent_hw, flags,     \
 					     fixed_rate)		      \
 	__clk_hw_register_fixed_rate((dev), NULL, (name), NULL, (parent_hw),  \
-				     NULL, (flags), (fixed_rate), 0, 0)
+				     NULL, (flags), (fixed_rate), 0, 0, false)
 /**
  * clk_hw_register_fixed_rate_parent_data - register fixed-rate clock with
  * the clock framework
@@ -392,7 +405,7 @@
 					     fixed_rate)		      \
 	__clk_hw_register_fixed_rate((dev), NULL, (name), NULL, NULL,	      \
 				     (parent_data), (flags), (fixed_rate), 0, \
-				     0)
+				     0, false)
 /**
  * clk_hw_register_fixed_rate_with_accuracy - register fixed-rate clock with
  * the clock framework
@@ -408,7 +421,7 @@
 						 fixed_accuracy)	      \
 	__clk_hw_register_fixed_rate((dev), NULL, (name), (parent_name),      \
 				     NULL, NULL, (flags), (fixed_rate),       \
-				     (fixed_accuracy), 0)
+				     (fixed_accuracy), 0, false)
 /**
  * clk_hw_register_fixed_rate_with_accuracy_parent_hw - register fixed-rate
  * clock with the clock framework
@@ -421,15 +434,15 @@
  */
 #define clk_hw_register_fixed_rate_with_accuracy_parent_hw(dev, name,	      \
 		parent_hw, flags, fixed_rate, fixed_accuracy)		      \
-	__clk_hw_register_fixed_rate((dev), NULL, (name), NULL, (parent_hw)   \
-				     NULL, NULL, (flags), (fixed_rate),	      \
-				     (fixed_accuracy), 0)
+	__clk_hw_register_fixed_rate((dev), NULL, (name), NULL, (parent_hw),  \
+				     NULL, (flags), (fixed_rate),	      \
+				     (fixed_accuracy), 0, false)
 /**
  * clk_hw_register_fixed_rate_with_accuracy_parent_data - register fixed-rate
  * clock with the clock framework
  * @dev: device that is registering this clock
  * @name: name of this clock
- * @parent_name: name of clock's parent
+ * @parent_data: name of clock's parent
  * @flags: framework-specific flags
  * @fixed_rate: non-adjustable clock rate
  * @fixed_accuracy: non-adjustable clock accuracy
@@ -438,7 +451,21 @@
 		parent_data, flags, fixed_rate, fixed_accuracy)		      \
 	__clk_hw_register_fixed_rate((dev), NULL, (name), NULL, NULL,	      \
 				     (parent_data), NULL, (flags),	      \
-				     (fixed_rate), (fixed_accuracy), 0)
+				     (fixed_rate), (fixed_accuracy), 0, false)
+/**
+ * clk_hw_register_fixed_rate_parent_accuracy - register fixed-rate clock with
+ * the clock framework
+ * @dev: device that is registering this clock
+ * @name: name of this clock
+ * @parent_data: name of clock's parent
+ * @flags: framework-specific flags
+ * @fixed_rate: non-adjustable clock rate
+ */
+#define clk_hw_register_fixed_rate_parent_accuracy(dev, name, parent_data,    \
+						   flags, fixed_rate)	      \
+	__clk_hw_register_fixed_rate((dev), NULL, (name), NULL, NULL,      \
+				     (parent_data), (flags), (fixed_rate), 0,    \
+				     CLK_FIXED_RATE_PARENT_ACCURACY, false)
 
 void clk_unregister_fixed_rate(struct clk *clk);
 void clk_hw_unregister_fixed_rate(struct clk_hw *hw);
@@ -566,7 +593,7 @@
  * Clock with an adjustable divider affecting its output frequency.  Implements
  * .recalc_rate, .set_rate and .round_rate
  *
- * Flags:
+ * @flags:
  * CLK_DIVIDER_ONE_BASED - by default the divisor is the value read from the
  *	register plus one.  If CLK_DIVIDER_ONE_BASED is set then the divider is
  *	the raw value read from the register, with the value of zero considered
@@ -915,6 +942,13 @@
 			      (parent_names), NULL, NULL, (flags), (reg),     \
 			      (shift), (mask), (clk_mux_flags), (table),      \
 			      (lock))
+#define clk_hw_register_mux_table_parent_data(dev, name, parent_data,	      \
+				  num_parents, flags, reg, shift, mask,	      \
+				  clk_mux_flags, table, lock)		      \
+	__clk_hw_register_mux((dev), NULL, (name), (num_parents),	      \
+			      NULL, NULL, (parent_data), (flags), (reg),      \
+			      (shift), (mask), (clk_mux_flags), (table),      \
+			      (lock))
 #define clk_hw_register_mux(dev, name, parent_names, num_parents, flags, reg, \
 			    shift, width, clk_mux_flags, lock)		      \
 	__clk_hw_register_mux((dev), NULL, (name), (num_parents),	      \
@@ -989,11 +1023,12 @@
  * @mwidth:	width of the numerator bit field
  * @nshift:	shift to the denominator bit field
  * @nwidth:	width of the denominator bit field
+ * @approximation: clk driver's callback for calculating the divider clock
  * @lock:	register lock
  *
  * Clock with adjustable fractional divider affecting its output frequency.
  *
- * Flags:
+ * @flags:
  * CLK_FRAC_DIVIDER_ZERO_BASED - by default the numerator and denominator
  *	is the value read from the register. If CLK_FRAC_DIVIDER_ZERO_BASED
  *	is set then the numerator and denominator are both the value read
@@ -1052,7 +1087,7 @@
  * Clock with an adjustable multiplier affecting its output frequency.
  * Implements .recalc_rate, .set_rate and .round_rate
  *
- * Flags:
+ * @flags:
  * CLK_MULTIPLIER_ZERO_BYPASS - By default, the multiplier is the value read
  *	from the register, with 0 being a valid value effectively
  *	zeroing the output clock rate. If CLK_MULTIPLIER_ZERO_BYPASS is
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/clk.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/clk.h
@@ -183,6 +183,51 @@
  */
 bool clk_is_match(const struct clk *p, const struct clk *q);
 
+/**
+ * clk_rate_exclusive_get - get exclusivity over the rate control of a
+ *                          producer
+ * @clk: clock source
+ *
+ * This function allows drivers to get exclusive control over the rate of a
+ * provider. It prevents any other consumer to execute, even indirectly,
+ * opereation which could alter the rate of the provider or cause glitches
+ *
+ * If exlusivity is claimed more than once on clock, even by the same driver,
+ * the rate effectively gets locked as exclusivity can't be preempted.
+ *
+ * Must not be called from within atomic context.
+ *
+ * Returns success (0) or negative errno.
+ */
+int clk_rate_exclusive_get(struct clk *clk);
+
+/**
+ * devm_clk_rate_exclusive_get - devm variant of clk_rate_exclusive_get
+ * @dev: device the exclusivity is bound to
+ * @clk: clock source
+ *
+ * Calls clk_rate_exclusive_get() on @clk and registers a devm cleanup handler
+ * on @dev to call clk_rate_exclusive_put().
+ *
+ * Must not be called from within atomic context.
+ */
+int devm_clk_rate_exclusive_get(struct device *dev, struct clk *clk);
+
+/**
+ * clk_rate_exclusive_put - release exclusivity over the rate control of a
+ *                          producer
+ * @clk: clock source
+ *
+ * This function allows drivers to release the exclusivity it previously got
+ * from clk_rate_exclusive_get()
+ *
+ * The caller must balance the number of clk_rate_exclusive_get() and
+ * clk_rate_exclusive_put() calls.
+ *
+ * Must not be called from within atomic context.
+ */
+void clk_rate_exclusive_put(struct clk *clk);
+
 #else
 
 static inline int clk_notifier_register(struct clk *clk,
@@ -236,6 +281,18 @@
 	return p == q;
 }
 
+static inline int clk_rate_exclusive_get(struct clk *clk)
+{
+	return 0;
+}
+
+static inline int devm_clk_rate_exclusive_get(struct device *dev, struct clk *clk)
+{
+	return 0;
+}
+
+static inline void clk_rate_exclusive_put(struct clk *clk) {}
+
 #endif
 
 #ifdef CONFIG_HAVE_CLK_PREPARE
@@ -459,6 +516,47 @@
 struct clk *devm_clk_get(struct device *dev, const char *id);
 
 /**
+ * devm_clk_get_prepared - devm_clk_get() + clk_prepare()
+ * @dev: device for clock "consumer"
+ * @id: clock consumer ID
+ *
+ * Context: May sleep.
+ *
+ * Return: a struct clk corresponding to the clock producer, or
+ * valid IS_ERR() condition containing errno.  The implementation
+ * uses @dev and @id to determine the clock consumer, and thereby
+ * the clock producer.  (IOW, @id may be identical strings, but
+ * clk_get may return different clock producers depending on @dev.)
+ *
+ * The returned clk (if valid) is prepared. Drivers must however assume
+ * that the clock is not enabled.
+ *
+ * The clock will automatically be unprepared and freed when the device
+ * is unbound from the bus.
+ */
+struct clk *devm_clk_get_prepared(struct device *dev, const char *id);
+
+/**
+ * devm_clk_get_enabled - devm_clk_get() + clk_prepare_enable()
+ * @dev: device for clock "consumer"
+ * @id: clock consumer ID
+ *
+ * Context: May sleep.
+ *
+ * Return: a struct clk corresponding to the clock producer, or
+ * valid IS_ERR() condition containing errno.  The implementation
+ * uses @dev and @id to determine the clock consumer, and thereby
+ * the clock producer.  (IOW, @id may be identical strings, but
+ * clk_get may return different clock producers depending on @dev.)
+ *
+ * The returned clk (if valid) is prepared and enabled.
+ *
+ * The clock will automatically be disabled, unprepared and freed
+ * when the device is unbound from the bus.
+ */
+struct clk *devm_clk_get_enabled(struct device *dev, const char *id);
+
+/**
  * devm_clk_get_optional - lookup and obtain a managed reference to an optional
  *			   clock producer.
  * @dev: device for clock "consumer"
@@ -470,53 +568,65 @@
 struct clk *devm_clk_get_optional(struct device *dev, const char *id);
 
 /**
- * devm_get_clk_from_child - lookup and obtain a managed reference to a
- *			     clock producer from child node.
+ * devm_clk_get_optional_prepared - devm_clk_get_optional() + clk_prepare()
  * @dev: device for clock "consumer"
- * @np: pointer to clock consumer node
- * @con_id: clock consumer ID
+ * @id: clock consumer ID
  *
- * This function parses the clocks, and uses them to look up the
- * struct clk from the registered list of clock providers by using
- * @np and @con_id
+ * Context: May sleep.
  *
- * The clock will automatically be freed when the device is unbound
- * from the bus.
+ * Return: a struct clk corresponding to the clock producer, or
+ * valid IS_ERR() condition containing errno.  The implementation
+ * uses @dev and @id to determine the clock consumer, and thereby
+ * the clock producer.  If no such clk is found, it returns NULL
+ * which serves as a dummy clk.  That's the only difference compared
+ * to devm_clk_get_prepared().
+ *
+ * The returned clk (if valid) is prepared. Drivers must however
+ * assume that the clock is not enabled.
+ *
+ * The clock will automatically be unprepared and freed when the
+ * device is unbound from the bus.
  */
-struct clk *devm_get_clk_from_child(struct device *dev,
-				    struct device_node *np, const char *con_id);
+struct clk *devm_clk_get_optional_prepared(struct device *dev, const char *id);
+
 /**
- * clk_rate_exclusive_get - get exclusivity over the rate control of a
- *                          producer
- * @clk: clock source
+ * devm_clk_get_optional_enabled - devm_clk_get_optional() +
+ *                                 clk_prepare_enable()
+ * @dev: device for clock "consumer"
+ * @id: clock consumer ID
  *
- * This function allows drivers to get exclusive control over the rate of a
- * provider. It prevents any other consumer to execute, even indirectly,
- * opereation which could alter the rate of the provider or cause glitches
+ * Context: May sleep.
  *
- * If exlusivity is claimed more than once on clock, even by the same driver,
- * the rate effectively gets locked as exclusivity can't be preempted.
+ * Return: a struct clk corresponding to the clock producer, or
+ * valid IS_ERR() condition containing errno.  The implementation
+ * uses @dev and @id to determine the clock consumer, and thereby
+ * the clock producer.  If no such clk is found, it returns NULL
+ * which serves as a dummy clk.  That's the only difference compared
+ * to devm_clk_get_enabled().
  *
- * Must not be called from within atomic context.
+ * The returned clk (if valid) is prepared and enabled.
  *
- * Returns success (0) or negative errno.
+ * The clock will automatically be disabled, unprepared and freed
+ * when the device is unbound from the bus.
  */
-int clk_rate_exclusive_get(struct clk *clk);
+struct clk *devm_clk_get_optional_enabled(struct device *dev, const char *id);
 
 /**
- * clk_rate_exclusive_put - release exclusivity over the rate control of a
- *                          producer
- * @clk: clock source
- *
- * This function allows drivers to release the exclusivity it previously got
- * from clk_rate_exclusive_get()
+ * devm_get_clk_from_child - lookup and obtain a managed reference to a
+ *			     clock producer from child node.
+ * @dev: device for clock "consumer"
+ * @np: pointer to clock consumer node
+ * @con_id: clock consumer ID
  *
- * The caller must balance the number of clk_rate_exclusive_get() and
- * clk_rate_exclusive_put() calls.
+ * This function parses the clocks, and uses them to look up the
+ * struct clk from the registered list of clock providers by using
+ * @np and @con_id
  *
- * Must not be called from within atomic context.
+ * The clock will automatically be freed when the device is unbound
+ * from the bus.
  */
-void clk_rate_exclusive_put(struct clk *clk);
+struct clk *devm_get_clk_from_child(struct device *dev,
+				    struct device_node *np, const char *con_id);
 
 /**
  * clk_enable - inform the system when the clock source should be running.
@@ -813,12 +923,36 @@
 	return NULL;
 }
 
+static inline struct clk *devm_clk_get_prepared(struct device *dev,
+						const char *id)
+{
+	return NULL;
+}
+
+static inline struct clk *devm_clk_get_enabled(struct device *dev,
+					       const char *id)
+{
+	return NULL;
+}
+
 static inline struct clk *devm_clk_get_optional(struct device *dev,
 						const char *id)
 {
 	return NULL;
 }
 
+static inline struct clk *devm_clk_get_optional_prepared(struct device *dev,
+							 const char *id)
+{
+	return NULL;
+}
+
+static inline struct clk *devm_clk_get_optional_enabled(struct device *dev,
+							const char *id)
+{
+	return NULL;
+}
+
 static inline int __must_check devm_clk_bulk_get(struct device *dev, int num_clks,
 						 struct clk_bulk_data *clks)
 {
@@ -852,14 +986,6 @@
 
 static inline void devm_clk_put(struct device *dev, struct clk *clk) {}
 
-
-static inline int clk_rate_exclusive_get(struct clk *clk)
-{
-	return 0;
-}
-
-static inline void clk_rate_exclusive_put(struct clk *clk) {}
-
 static inline int clk_enable(struct clk *clk)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/clk/zynq.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/clk/zynq.h
@@ -9,6 +9,10 @@
 
 #include <linux/spinlock.h>
 
+int zynq_clk_suspend_early(void);
+void zynq_clk_resume_late(void);
+void zynq_clk_topswitch_enable(void);
+void zynq_clk_topswitch_disable(void);
 void zynq_clock_init(void);
 
 struct clk *clk_register_zynq_pll(const char *name, const char *parent,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/clocksource.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/clocksource.h
@@ -291,7 +291,19 @@
 #define TIMER_ACPI_DECLARE(name, table_id, fn)		\
 	ACPI_DECLARE_PROBE_ENTRY(timer, name, table_id, 0, NULL, 0, fn)
 
-extern ulong max_cswd_read_retries;
+static inline unsigned int clocksource_get_max_watchdog_retry(void)
+{
+	/*
+	 * When system is in the boot phase or under heavy workload, there
+	 * can be random big latencies during the clocksource/watchdog
+	 * read, so allow retries to filter the noise latency. As the
+	 * latency's frequency and maximum value goes up with the number of
+	 * CPUs, scale the number of retries with the number of online
+	 * CPUs.
+	 */
+	return (ilog2(num_online_cpus()) / 2) + 1;
+}
+
 void clocksource_verify_percpu(struct clocksource *cs);
 
 #endif /* _LINUX_CLOCKSOURCE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cma.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cma.h
@@ -20,6 +20,15 @@
 
 #define CMA_MAX_NAME 64
 
+/*
+ * TODO: once the buddy -- especially pageblock merging and alloc_contig_range()
+ * -- can deal with only some pageblocks of a higher-order page being
+ *  MIGRATE_CMA, we can use pageblock_nr_pages.
+ */
+#define CMA_MIN_ALIGNMENT_PAGES max_t(phys_addr_t, MAX_ORDER_NR_PAGES, \
+				      pageblock_nr_pages)
+#define CMA_MIN_ALIGNMENT_BYTES (PAGE_SIZE * CMA_MIN_ALIGNMENT_PAGES)
+
 struct cma;
 
 extern unsigned long totalcma_pages;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/compat.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/compat.h
@@ -235,6 +235,7 @@
 				struct {
 					compat_ulong_t _data;
 					u32 _type;
+					u32 _flags;
 				} _perf;
 			};
 		} _sigfault;
@@ -589,7 +590,7 @@
 asmlinkage long compat_sys_fstatfs64(unsigned int fd, compat_size_t sz,
 				     struct compat_statfs64 __user *buf);
 asmlinkage long compat_sys_truncate(const char __user *, compat_off_t);
-asmlinkage long compat_sys_ftruncate(unsigned int, compat_ulong_t);
+asmlinkage long compat_sys_ftruncate(unsigned int, compat_off_t);
 /* No generic prototype for truncate64, ftruncate64, fallocate */
 asmlinkage long compat_sys_openat(int dfd, const char __user *filename,
 				  int flags, umode_t mode);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/compiler-gcc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/compiler-gcc.h
@@ -144,3 +144,11 @@
 #else
 #define __diag_GCC_8(s)
 #endif
+
+/*
+ * Prior to 9.1, -Wno-alloc-size-larger-than (and therefore the "alloc_size"
+ * attribute) do not work, and must be disabled.
+ */
+#if GCC_VERSION < 90100
+#undef __alloc_size__
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/compiler.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/compiler.h
@@ -117,40 +117,29 @@
  */
 #define __stringify_label(n) #n
 
-#define __annotate_reachable(c) ({					\
-	asm volatile(__stringify_label(c) ":\n\t"			\
-		     ".pushsection .discard.reachable\n\t"		\
-		     ".long " __stringify_label(c) "b - .\n\t"		\
-		     ".popsection\n\t");				\
-})
-#define annotate_reachable() __annotate_reachable(__COUNTER__)
-
 #define __annotate_unreachable(c) ({					\
 	asm volatile(__stringify_label(c) ":\n\t"			\
 		     ".pushsection .discard.unreachable\n\t"		\
 		     ".long " __stringify_label(c) "b - .\n\t"		\
-		     ".popsection\n\t");				\
+		     ".popsection\n\t" : : "i" (c));			\
 })
 #define annotate_unreachable() __annotate_unreachable(__COUNTER__)
 
-#define ASM_UNREACHABLE							\
-	"999:\n\t"							\
-	".pushsection .discard.unreachable\n\t"				\
-	".long 999b - .\n\t"						\
+#define ASM_REACHABLE							\
+	"998:\n\t"							\
+	".pushsection .discard.reachable\n\t"				\
+	".long 998b - .\n\t"						\
 	".popsection\n\t"
 
 /* Annotate a C jump table to allow objtool to follow the code flow */
 #define __annotate_jump_table __section(".rodata..c_jump_table")
 
 #else
-#define annotate_reachable()
 #define annotate_unreachable()
+# define ASM_REACHABLE
 #define __annotate_jump_table
 #endif
 
-#ifndef ASM_UNREACHABLE
-# define ASM_UNREACHABLE
-#endif
 #ifndef unreachable
 # define unreachable() do {		\
 	annotate_unreachable();		\
@@ -233,6 +222,23 @@
 
 #endif /* __KERNEL__ */
 
+/**
+ * offset_to_ptr - convert a relative memory offset to an absolute pointer
+ * @off:	the address of the 32-bit offset value
+ */
+static inline void *offset_to_ptr(const int *off)
+{
+	return (void *)((unsigned long)off + *off);
+}
+
+#endif /* __ASSEMBLY__ */
+
+#ifdef CONFIG_64BIT
+#define ARCH_SEL(a,b) a
+#else
+#define ARCH_SEL(a,b) b
+#endif
+
 /*
  * Force the compiler to emit 'sym' as a symbol, so that we can reference
  * it from inline assembler. Necessary in case 'sym' could be inlined
@@ -243,21 +249,24 @@
 	static void * __section(".discard.addressable") __used \
 		__UNIQUE_ID(__PASTE(__addressable_,sym)) = (void *)&sym;
 
-/**
- * offset_to_ptr - convert a relative memory offset to an absolute pointer
- * @off:	the address of the 32-bit offset value
- */
-static inline void *offset_to_ptr(const int *off)
-{
-	return (void *)((unsigned long)off + *off);
-}
+#define __ADDRESSABLE_ASM(sym)						\
+	.pushsection .discard.addressable,"aw";				\
+	.align ARCH_SEL(8,4);						\
+	ARCH_SEL(.quad, .long) __stringify(sym);			\
+	.popsection;
 
-#endif /* __ASSEMBLY__ */
+#define __ADDRESSABLE_ASM_STR(sym) __stringify(__ADDRESSABLE_ASM(sym))
 
 /* &a[0] degrades to a pointer: a different type from an array */
 #define __must_be_array(a)	BUILD_BUG_ON_ZERO(__same_type((a), &(a)[0]))
 
 /*
+ * Whether 'type' is a signed type or an unsigned type. Supports scalar types,
+ * bool and also pointer types.
+ */
+#define is_signed_type(type) (((type)(-1)) < (__force type)1)
+
+/*
  * This is needed in functions which generate the stack canary, see
  * arch/x86/kernel/smpboot.c::start_secondary() for an example.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/compiler_attributes.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/compiler_attributes.h
@@ -34,6 +34,15 @@
 #define __aligned_largest               __attribute__((__aligned__))
 
 /*
+ * Note: do not use this directly. Instead, use __alloc_size() since it is conditionally
+ * available and includes other attributes.
+ *
+ *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html#index-alloc_005fsize-function-attribute
+ * clang: https://clang.llvm.org/docs/AttributeReference.html#alloc-size
+ */
+#define __alloc_size__(x, ...)		__attribute__((__alloc_size__(x, ## __VA_ARGS__)))
+
+/*
  * Note: users of __always_inline currently do not write "inline" themselves,
  * which seems to be required by gcc to apply the attribute according
  * to its docs (and also "warning: always_inline function might not be
@@ -153,6 +162,7 @@
 
 /*
  *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html#index-malloc-function-attribute
+ * clang: https://clang.llvm.org/docs/AttributeReference.html#malloc
  */
 #define __malloc                        __attribute__((__malloc__))
 
@@ -267,6 +277,18 @@
 #define __section(section)              __attribute__((__section__(section)))
 
 /*
+ * Optional: only supported since gcc >= 12
+ *
+ *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Variable-Attributes.html#index-uninitialized-variable-attribute
+ * clang: https://clang.llvm.org/docs/AttributeReference.html#uninitialized
+ */
+#if __has_attribute(__uninitialized__)
+# define __uninitialized		__attribute__((__uninitialized__))
+#else
+# define __uninitialized
+#endif
+
+/*
  *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html#index-unused-function-attribute
  *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Type-Attributes.html#index-unused-type-attribute
  *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Variable-Attributes.html#index-unused-variable-attribute
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/compiler_types.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/compiler_types.h
@@ -250,6 +250,18 @@
 # define __cficanonical
 #endif
 
+/*
+ * Any place that could be marked with the "alloc_size" attribute is also
+ * a place to be marked with the "malloc" attribute. Do this as part of the
+ * __alloc_size macro to avoid redundant attributes and to avoid missing a
+ * __malloc marking.
+ */
+#ifdef __alloc_size__
+# define __alloc_size(x, ...)	__alloc_size__(x, ## __VA_ARGS__) __malloc
+#else
+# define __alloc_size(x, ...)	__malloc
+#endif
+
 #ifndef asm_volatile_goto
 #define asm_volatile_goto(x...) asm goto(x)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/console.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/console.h
@@ -149,6 +149,8 @@
 	short	flags;
 	short	index;
 	int	cflag;
+	uint	ispeed;
+	uint	ospeed;
 	void	*data;
 	struct	 console *next;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/coredump.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/coredump.h
@@ -12,6 +12,8 @@
 	unsigned long start, end;
 	unsigned long flags;
 	unsigned long dump_size;
+	unsigned long pgoff;
+	struct file   *file;
 };
 
 extern int core_uses_pid;
@@ -29,9 +31,6 @@
 extern int dump_align(struct coredump_params *cprm, int align);
 int dump_user_range(struct coredump_params *cprm, unsigned long start,
 		    unsigned long len);
-int dump_vma_snapshot(struct coredump_params *cprm, int *vma_count,
-		      struct core_vma_metadata **vma_meta,
-		      size_t *vma_data_size_ptr);
 extern void do_coredump(const kernel_siginfo_t *siginfo);
 #else
 static inline void do_coredump(const kernel_siginfo_t *siginfo) {}
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/counter.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/counter.h
@@ -6,42 +6,184 @@
 #ifndef _COUNTER_H_
 #define _COUNTER_H_
 
-#include <linux/counter_enum.h>
 #include <linux/device.h>
+#include <linux/kernel.h>
 #include <linux/types.h>
 
+struct counter_device;
+struct counter_count;
+struct counter_synapse;
+struct counter_signal;
+
+enum counter_comp_type {
+	COUNTER_COMP_U8,
+	COUNTER_COMP_U64,
+	COUNTER_COMP_BOOL,
+	COUNTER_COMP_SIGNAL_LEVEL,
+	COUNTER_COMP_FUNCTION,
+	COUNTER_COMP_SYNAPSE_ACTION,
+	COUNTER_COMP_ENUM,
+	COUNTER_COMP_COUNT_DIRECTION,
+	COUNTER_COMP_COUNT_MODE,
+};
+
+enum counter_scope {
+	COUNTER_SCOPE_DEVICE,
+	COUNTER_SCOPE_SIGNAL,
+	COUNTER_SCOPE_COUNT,
+};
+
 enum counter_count_direction {
-	COUNTER_COUNT_DIRECTION_FORWARD = 0,
-	COUNTER_COUNT_DIRECTION_BACKWARD
+	COUNTER_COUNT_DIRECTION_FORWARD,
+	COUNTER_COUNT_DIRECTION_BACKWARD,
 };
-extern const char *const counter_count_direction_str[2];
 
 enum counter_count_mode {
-	COUNTER_COUNT_MODE_NORMAL = 0,
+	COUNTER_COUNT_MODE_NORMAL,
 	COUNTER_COUNT_MODE_RANGE_LIMIT,
 	COUNTER_COUNT_MODE_NON_RECYCLE,
-	COUNTER_COUNT_MODE_MODULO_N
+	COUNTER_COUNT_MODE_MODULO_N,
 };
-extern const char *const counter_count_mode_str[4];
 
-struct counter_device;
-struct counter_signal;
+enum counter_function {
+	COUNTER_FUNCTION_INCREASE,
+	COUNTER_FUNCTION_DECREASE,
+	COUNTER_FUNCTION_PULSE_DIRECTION,
+	COUNTER_FUNCTION_QUADRATURE_X1_A,
+	COUNTER_FUNCTION_QUADRATURE_X1_B,
+	COUNTER_FUNCTION_QUADRATURE_X2_A,
+	COUNTER_FUNCTION_QUADRATURE_X2_B,
+	COUNTER_FUNCTION_QUADRATURE_X4,
+};
+
+enum counter_signal_level {
+	COUNTER_SIGNAL_LEVEL_LOW,
+	COUNTER_SIGNAL_LEVEL_HIGH,
+};
+
+enum counter_synapse_action {
+	COUNTER_SYNAPSE_ACTION_NONE,
+	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
+	COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
+	COUNTER_SYNAPSE_ACTION_BOTH_EDGES,
+};
 
 /**
- * struct counter_signal_ext - Counter Signal extensions
- * @name:	attribute name
- * @read:	read callback for this attribute; may be NULL
- * @write:	write callback for this attribute; may be NULL
- * @priv:	data private to the driver
+ * struct counter_comp - Counter component node
+ * @type:		Counter component data type
+ * @name:		device-specific component name
+ * @priv:		component-relevant data
+ * @action_read:		Synapse action mode read callback. The read value of the
+ *			respective Synapse action mode should be passed back via
+ *			the action parameter.
+ * @device_u8_read:		Device u8 component read callback. The read value of the
+ *			respective Device u8 component should be passed back via
+ *			the val parameter.
+ * @count_u8_read:		Count u8 component read callback. The read value of the
+ *			respective Count u8 component should be passed back via
+ *			the val parameter.
+ * @signal_u8_read:		Signal u8 component read callback. The read value of the
+ *			respective Signal u8 component should be passed back via
+ *			the val parameter.
+ * @device_u32_read:		Device u32 component read callback. The read value of
+ *			the respective Device u32 component should be passed
+ *			back via the val parameter.
+ * @count_u32_read:		Count u32 component read callback. The read value of the
+ *			respective Count u32 component should be passed back via
+ *			the val parameter.
+ * @signal_u32_read:		Signal u32 component read callback. The read value of
+ *			the respective Signal u32 component should be passed
+ *			back via the val parameter.
+ * @device_u64_read:		Device u64 component read callback. The read value of
+ *			the respective Device u64 component should be passed
+ *			back via the val parameter.
+ * @count_u64_read:		Count u64 component read callback. The read value of the
+ *			respective Count u64 component should be passed back via
+ *			the val parameter.
+ * @signal_u64_read:		Signal u64 component read callback. The read value of
+ *			the respective Signal u64 component should be passed
+ *			back via the val parameter.
+ * @action_write:		Synapse action mode write callback. The write value of
+ *			the respective Synapse action mode is passed via the
+ *			action parameter.
+ * @device_u8_write:		Device u8 component write callback. The write value of
+ *			the respective Device u8 component is passed via the val
+ *			parameter.
+ * @count_u8_write:		Count u8 component write callback. The write value of
+ *			the respective Count u8 component is passed via the val
+ *			parameter.
+ * @signal_u8_write:		Signal u8 component write callback. The write value of
+ *			the respective Signal u8 component is passed via the val
+ *			parameter.
+ * @device_u32_write:		Device u32 component write callback. The write value of
+ *			the respective Device u32 component is passed via the
+ *			val parameter.
+ * @count_u32_write:		Count u32 component write callback. The write value of
+ *			the respective Count u32 component is passed via the val
+ *			parameter.
+ * @signal_u32_write:		Signal u32 component write callback. The write value of
+ *			the respective Signal u32 component is passed via the
+ *			val parameter.
+ * @device_u64_write:		Device u64 component write callback. The write value of
+ *			the respective Device u64 component is passed via the
+ *			val parameter.
+ * @count_u64_write:		Count u64 component write callback. The write value of
+ *			the respective Count u64 component is passed via the val
+ *			parameter.
+ * @signal_u64_write:		Signal u64 component write callback. The write value of
+ *			the respective Signal u64 component is passed via the
+ *			val parameter.
  */
-struct counter_signal_ext {
+struct counter_comp {
+	enum counter_comp_type type;
 	const char *name;
-	ssize_t (*read)(struct counter_device *counter,
-			struct counter_signal *signal, void *priv, char *buf);
-	ssize_t (*write)(struct counter_device *counter,
-			 struct counter_signal *signal, void *priv,
-			 const char *buf, size_t len);
 	void *priv;
+	union {
+		int (*action_read)(struct counter_device *counter,
+				   struct counter_count *count,
+				   struct counter_synapse *synapse,
+				   enum counter_synapse_action *action);
+		int (*device_u8_read)(struct counter_device *counter, u8 *val);
+		int (*count_u8_read)(struct counter_device *counter,
+				     struct counter_count *count, u8 *val);
+		int (*signal_u8_read)(struct counter_device *counter,
+				      struct counter_signal *signal, u8 *val);
+		int (*device_u32_read)(struct counter_device *counter,
+				       u32 *val);
+		int (*count_u32_read)(struct counter_device *counter,
+				      struct counter_count *count, u32 *val);
+		int (*signal_u32_read)(struct counter_device *counter,
+				       struct counter_signal *signal, u32 *val);
+		int (*device_u64_read)(struct counter_device *counter,
+				       u64 *val);
+		int (*count_u64_read)(struct counter_device *counter,
+				      struct counter_count *count, u64 *val);
+		int (*signal_u64_read)(struct counter_device *counter,
+				       struct counter_signal *signal, u64 *val);
+	};
+	union {
+		int (*action_write)(struct counter_device *counter,
+				    struct counter_count *count,
+				    struct counter_synapse *synapse,
+				    enum counter_synapse_action action);
+		int (*device_u8_write)(struct counter_device *counter, u8 val);
+		int (*count_u8_write)(struct counter_device *counter,
+				      struct counter_count *count, u8 val);
+		int (*signal_u8_write)(struct counter_device *counter,
+				       struct counter_signal *signal, u8 val);
+		int (*device_u32_write)(struct counter_device *counter,
+					u32 val);
+		int (*count_u32_write)(struct counter_device *counter,
+				       struct counter_count *count, u32 val);
+		int (*signal_u32_write)(struct counter_device *counter,
+					struct counter_signal *signal, u32 val);
+		int (*device_u64_write)(struct counter_device *counter,
+					u64 val);
+		int (*count_u64_write)(struct counter_device *counter,
+				       struct counter_count *count, u64 val);
+		int (*signal_u64_write)(struct counter_device *counter,
+					struct counter_signal *signal, u64 val);
+	};
 };
 
 /**
@@ -51,248 +193,52 @@
  *		as it appears in the datasheet documentation
  * @ext:	optional array of Counter Signal extensions
  * @num_ext:	number of Counter Signal extensions specified in @ext
- * @priv:	optional private data supplied by driver
  */
 struct counter_signal {
 	int id;
 	const char *name;
 
-	const struct counter_signal_ext *ext;
+	struct counter_comp *ext;
 	size_t num_ext;
-
-	void *priv;
-};
-
-/**
- * struct counter_signal_enum_ext - Signal enum extension attribute
- * @items:	Array of strings
- * @num_items:	Number of items specified in @items
- * @set:	Set callback function; may be NULL
- * @get:	Get callback function; may be NULL
- *
- * The counter_signal_enum_ext structure can be used to implement enum style
- * Signal extension attributes. Enum style attributes are those which have a set
- * of strings that map to unsigned integer values. The Generic Counter Signal
- * enum extension helper code takes care of mapping between value and string, as
- * well as generating a "_available" file which contains a list of all available
- * items. The get callback is used to query the currently active item; the index
- * of the item within the respective items array is returned via the 'item'
- * parameter. The set callback is called when the attribute is updated; the
- * 'item' parameter contains the index of the newly activated item within the
- * respective items array.
- */
-struct counter_signal_enum_ext {
-	const char * const *items;
-	size_t num_items;
-	int (*get)(struct counter_device *counter,
-		   struct counter_signal *signal, size_t *item);
-	int (*set)(struct counter_device *counter,
-		   struct counter_signal *signal, size_t item);
-};
-
-/**
- * COUNTER_SIGNAL_ENUM() - Initialize Signal enum extension
- * @_name:	Attribute name
- * @_e:		Pointer to a counter_signal_enum_ext structure
- *
- * This should usually be used together with COUNTER_SIGNAL_ENUM_AVAILABLE()
- */
-#define COUNTER_SIGNAL_ENUM(_name, _e) \
-{ \
-	.name = (_name), \
-	.read = counter_signal_enum_read, \
-	.write = counter_signal_enum_write, \
-	.priv = (_e) \
-}
-
-/**
- * COUNTER_SIGNAL_ENUM_AVAILABLE() - Initialize Signal enum available extension
- * @_name:	Attribute name ("_available" will be appended to the name)
- * @_e:		Pointer to a counter_signal_enum_ext structure
- *
- * Creates a read only attribute that lists all the available enum items in a
- * newline separated list. This should usually be used together with
- * COUNTER_SIGNAL_ENUM()
- */
-#define COUNTER_SIGNAL_ENUM_AVAILABLE(_name, _e) \
-{ \
-	.name = (_name "_available"), \
-	.read = counter_signal_enum_available_read, \
-	.priv = (_e) \
-}
-
-enum counter_synapse_action {
-	COUNTER_SYNAPSE_ACTION_NONE = 0,
-	COUNTER_SYNAPSE_ACTION_RISING_EDGE,
-	COUNTER_SYNAPSE_ACTION_FALLING_EDGE,
-	COUNTER_SYNAPSE_ACTION_BOTH_EDGES
 };
 
 /**
  * struct counter_synapse - Counter Synapse node
- * @action:		index of current action mode
  * @actions_list:	array of available action modes
  * @num_actions:	number of action modes specified in @actions_list
  * @signal:		pointer to associated signal
  */
 struct counter_synapse {
-	size_t action;
 	const enum counter_synapse_action *actions_list;
 	size_t num_actions;
 
 	struct counter_signal *signal;
 };
 
-struct counter_count;
-
-/**
- * struct counter_count_ext - Counter Count extension
- * @name:	attribute name
- * @read:	read callback for this attribute; may be NULL
- * @write:	write callback for this attribute; may be NULL
- * @priv:	data private to the driver
- */
-struct counter_count_ext {
-	const char *name;
-	ssize_t (*read)(struct counter_device *counter,
-			struct counter_count *count, void *priv, char *buf);
-	ssize_t (*write)(struct counter_device *counter,
-			 struct counter_count *count, void *priv,
-			 const char *buf, size_t len);
-	void *priv;
-};
-
-enum counter_function {
-	COUNTER_FUNCTION_INCREASE = 0,
-	COUNTER_FUNCTION_DECREASE,
-	COUNTER_FUNCTION_PULSE_DIRECTION,
-	COUNTER_FUNCTION_QUADRATURE_X1_A,
-	COUNTER_FUNCTION_QUADRATURE_X1_B,
-	COUNTER_FUNCTION_QUADRATURE_X2_A,
-	COUNTER_FUNCTION_QUADRATURE_X2_B,
-	COUNTER_FUNCTION_QUADRATURE_X4
-};
-
 /**
  * struct counter_count - Counter Count node
  * @id:			unique ID used to identify Count
  * @name:		device-specific Count name; ideally, this should match
  *			the name as it appears in the datasheet documentation
- * @function:		index of current function mode
  * @functions_list:	array available function modes
  * @num_functions:	number of function modes specified in @functions_list
  * @synapses:		array of synapses for initialization
  * @num_synapses:	number of synapses specified in @synapses
  * @ext:		optional array of Counter Count extensions
  * @num_ext:		number of Counter Count extensions specified in @ext
- * @priv:		optional private data supplied by driver
  */
 struct counter_count {
 	int id;
 	const char *name;
 
-	size_t function;
 	const enum counter_function *functions_list;
 	size_t num_functions;
 
 	struct counter_synapse *synapses;
 	size_t num_synapses;
 
-	const struct counter_count_ext *ext;
+	struct counter_comp *ext;
 	size_t num_ext;
-
-	void *priv;
-};
-
-/**
- * struct counter_count_enum_ext - Count enum extension attribute
- * @items:	Array of strings
- * @num_items:	Number of items specified in @items
- * @set:	Set callback function; may be NULL
- * @get:	Get callback function; may be NULL
- *
- * The counter_count_enum_ext structure can be used to implement enum style
- * Count extension attributes. Enum style attributes are those which have a set
- * of strings that map to unsigned integer values. The Generic Counter Count
- * enum extension helper code takes care of mapping between value and string, as
- * well as generating a "_available" file which contains a list of all available
- * items. The get callback is used to query the currently active item; the index
- * of the item within the respective items array is returned via the 'item'
- * parameter. The set callback is called when the attribute is updated; the
- * 'item' parameter contains the index of the newly activated item within the
- * respective items array.
- */
-struct counter_count_enum_ext {
-	const char * const *items;
-	size_t num_items;
-	int (*get)(struct counter_device *counter, struct counter_count *count,
-		   size_t *item);
-	int (*set)(struct counter_device *counter, struct counter_count *count,
-		   size_t item);
-};
-
-/**
- * COUNTER_COUNT_ENUM() - Initialize Count enum extension
- * @_name:	Attribute name
- * @_e:		Pointer to a counter_count_enum_ext structure
- *
- * This should usually be used together with COUNTER_COUNT_ENUM_AVAILABLE()
- */
-#define COUNTER_COUNT_ENUM(_name, _e) \
-{ \
-	.name = (_name), \
-	.read = counter_count_enum_read, \
-	.write = counter_count_enum_write, \
-	.priv = (_e) \
-}
-
-/**
- * COUNTER_COUNT_ENUM_AVAILABLE() - Initialize Count enum available extension
- * @_name:	Attribute name ("_available" will be appended to the name)
- * @_e:		Pointer to a counter_count_enum_ext structure
- *
- * Creates a read only attribute that lists all the available enum items in a
- * newline separated list. This should usually be used together with
- * COUNTER_COUNT_ENUM()
- */
-#define COUNTER_COUNT_ENUM_AVAILABLE(_name, _e) \
-{ \
-	.name = (_name "_available"), \
-	.read = counter_count_enum_available_read, \
-	.priv = (_e) \
-}
-
-/**
- * struct counter_device_attr_group - internal container for attribute group
- * @attr_group:	Counter sysfs attributes group
- * @attr_list:	list to keep track of created Counter sysfs attributes
- * @num_attr:	number of Counter sysfs attributes
- */
-struct counter_device_attr_group {
-	struct attribute_group attr_group;
-	struct list_head attr_list;
-	size_t num_attr;
-};
-
-/**
- * struct counter_device_state - internal state container for a Counter device
- * @id:			unique ID used to identify the Counter
- * @dev:		internal device structure
- * @groups_list:	attribute groups list (for Signals, Counts, and ext)
- * @num_groups:		number of attribute groups containers
- * @groups:		Counter sysfs attribute groups (to populate @dev.groups)
- */
-struct counter_device_state {
-	int id;
-	struct device dev;
-	struct counter_device_attr_group *groups_list;
-	size_t num_groups;
-	const struct attribute_group **groups;
-};
-
-enum counter_signal_level {
-	COUNTER_SIGNAL_LEVEL_LOW,
-	COUNTER_SIGNAL_LEVEL_HIGH,
 };
 
 /**
@@ -306,117 +252,47 @@
  * @count_write:	optional write callback for Count attribute. The write
  *			value for the respective Count is passed in via the val
  *			parameter.
- * @function_get:	function to get the current count function mode. Returns
- *			0 on success and negative error code on error. The index
- *			of the respective Count's returned function mode should
- *			be passed back via the function parameter.
- * @function_set:	function to set the count function mode. function is the
- *			index of the requested function mode from the respective
- *			Count's functions_list array.
- * @action_get:		function to get the current action mode. Returns 0 on
- *			success and negative error code on error. The index of
- *			the respective Synapse's returned action mode should be
- *			passed back via the action parameter.
- * @action_set:		function to set the action mode. action is the index of
- *			the requested action mode from the respective Synapse's
- *			actions_list array.
+ * @function_read:	read callback the Count function modes. The read
+ *			function mode of the respective Count should be passed
+ *			back via the function parameter.
+ * @function_write:	write callback for Count function modes. The function
+ *			mode to write for the respective Count is passed in via
+ *			the function parameter.
+ * @action_read:	read callback the Synapse action modes. The read action
+ *			mode of the respective Synapse should be passed back via
+ *			the action parameter.
+ * @action_write:	write callback for Synapse action modes. The action mode
+ *			to write for the respective Synapse is passed in via the
+ *			action parameter.
  */
 struct counter_ops {
 	int (*signal_read)(struct counter_device *counter,
 			   struct counter_signal *signal,
 			   enum counter_signal_level *level);
 	int (*count_read)(struct counter_device *counter,
-			  struct counter_count *count, unsigned long *val);
+			  struct counter_count *count, u64 *value);
 	int (*count_write)(struct counter_device *counter,
-			   struct counter_count *count, unsigned long val);
-	int (*function_get)(struct counter_device *counter,
-			    struct counter_count *count, size_t *function);
-	int (*function_set)(struct counter_device *counter,
-			    struct counter_count *count, size_t function);
-	int (*action_get)(struct counter_device *counter,
-			  struct counter_count *count,
-			  struct counter_synapse *synapse, size_t *action);
-	int (*action_set)(struct counter_device *counter,
-			  struct counter_count *count,
-			  struct counter_synapse *synapse, size_t action);
-};
-
-/**
- * struct counter_device_ext - Counter device extension
- * @name:	attribute name
- * @read:	read callback for this attribute; may be NULL
- * @write:	write callback for this attribute; may be NULL
- * @priv:	data private to the driver
- */
-struct counter_device_ext {
-	const char *name;
-	ssize_t (*read)(struct counter_device *counter, void *priv, char *buf);
-	ssize_t (*write)(struct counter_device *counter, void *priv,
-			 const char *buf, size_t len);
-	void *priv;
-};
-
-/**
- * struct counter_device_enum_ext - Counter enum extension attribute
- * @items:	Array of strings
- * @num_items:	Number of items specified in @items
- * @set:	Set callback function; may be NULL
- * @get:	Get callback function; may be NULL
- *
- * The counter_device_enum_ext structure can be used to implement enum style
- * Counter extension attributes. Enum style attributes are those which have a
- * set of strings that map to unsigned integer values. The Generic Counter enum
- * extension helper code takes care of mapping between value and string, as well
- * as generating a "_available" file which contains a list of all available
- * items. The get callback is used to query the currently active item; the index
- * of the item within the respective items array is returned via the 'item'
- * parameter. The set callback is called when the attribute is updated; the
- * 'item' parameter contains the index of the newly activated item within the
- * respective items array.
- */
-struct counter_device_enum_ext {
-	const char * const *items;
-	size_t num_items;
-	int (*get)(struct counter_device *counter, size_t *item);
-	int (*set)(struct counter_device *counter, size_t item);
+			   struct counter_count *count, u64 value);
+	int (*function_read)(struct counter_device *counter,
+			     struct counter_count *count,
+			     enum counter_function *function);
+	int (*function_write)(struct counter_device *counter,
+			      struct counter_count *count,
+			      enum counter_function function);
+	int (*action_read)(struct counter_device *counter,
+			   struct counter_count *count,
+			   struct counter_synapse *synapse,
+			   enum counter_synapse_action *action);
+	int (*action_write)(struct counter_device *counter,
+			    struct counter_count *count,
+			    struct counter_synapse *synapse,
+			    enum counter_synapse_action action);
 };
 
 /**
- * COUNTER_DEVICE_ENUM() - Initialize Counter enum extension
- * @_name:	Attribute name
- * @_e:		Pointer to a counter_device_enum_ext structure
- *
- * This should usually be used together with COUNTER_DEVICE_ENUM_AVAILABLE()
- */
-#define COUNTER_DEVICE_ENUM(_name, _e) \
-{ \
-	.name = (_name), \
-	.read = counter_device_enum_read, \
-	.write = counter_device_enum_write, \
-	.priv = (_e) \
-}
-
-/**
- * COUNTER_DEVICE_ENUM_AVAILABLE() - Initialize Counter enum available extension
- * @_name:	Attribute name ("_available" will be appended to the name)
- * @_e:		Pointer to a counter_device_enum_ext structure
- *
- * Creates a read only attribute that lists all the available enum items in a
- * newline separated list. This should usually be used together with
- * COUNTER_DEVICE_ENUM()
- */
-#define COUNTER_DEVICE_ENUM_AVAILABLE(_name, _e) \
-{ \
-	.name = (_name "_available"), \
-	.read = counter_device_enum_available_read, \
-	.priv = (_e) \
-}
-
-/**
  * struct counter_device - Counter data structure
  * @name:		name of the device as it appears in the datasheet
  * @parent:		optional parent device providing the counters
- * @device_state:	internal device state container
  * @ops:		callbacks from driver
  * @signals:		array of Signals
  * @num_signals:	number of Signals specified in @signals
@@ -425,11 +301,11 @@
  * @ext:		optional array of Counter device extensions
  * @num_ext:		number of Counter device extensions specified in @ext
  * @priv:		optional private data supplied by driver
+ * @dev:		internal device structure
  */
 struct counter_device {
 	const char *name;
 	struct device *parent;
-	struct counter_device_state *device_state;
 
 	const struct counter_ops *ops;
 
@@ -438,17 +314,159 @@
 	struct counter_count *counts;
 	size_t num_counts;
 
-	const struct counter_device_ext *ext;
+	struct counter_comp *ext;
 	size_t num_ext;
 
 	void *priv;
+
+	struct device dev;
 };
 
 int counter_register(struct counter_device *const counter);
 void counter_unregister(struct counter_device *const counter);
 int devm_counter_register(struct device *dev,
 			  struct counter_device *const counter);
-void devm_counter_unregister(struct device *dev,
-			     struct counter_device *const counter);
+
+#define COUNTER_COMP_DEVICE_U8(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_U8, \
+	.name = (_name), \
+	.device_u8_read = (_read), \
+	.device_u8_write = (_write), \
+}
+#define COUNTER_COMP_COUNT_U8(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_U8, \
+	.name = (_name), \
+	.count_u8_read = (_read), \
+	.count_u8_write = (_write), \
+}
+#define COUNTER_COMP_SIGNAL_U8(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_U8, \
+	.name = (_name), \
+	.signal_u8_read = (_read), \
+	.signal_u8_write = (_write), \
+}
+
+#define COUNTER_COMP_DEVICE_U64(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_U64, \
+	.name = (_name), \
+	.device_u64_read = (_read), \
+	.device_u64_write = (_write), \
+}
+#define COUNTER_COMP_COUNT_U64(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_U64, \
+	.name = (_name), \
+	.count_u64_read = (_read), \
+	.count_u64_write = (_write), \
+}
+#define COUNTER_COMP_SIGNAL_U64(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_U64, \
+	.name = (_name), \
+	.signal_u64_read = (_read), \
+	.signal_u64_write = (_write), \
+}
+
+#define COUNTER_COMP_DEVICE_BOOL(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_BOOL, \
+	.name = (_name), \
+	.device_u8_read = (_read), \
+	.device_u8_write = (_write), \
+}
+#define COUNTER_COMP_COUNT_BOOL(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_BOOL, \
+	.name = (_name), \
+	.count_u8_read = (_read), \
+	.count_u8_write = (_write), \
+}
+#define COUNTER_COMP_SIGNAL_BOOL(_name, _read, _write) \
+{ \
+	.type = COUNTER_COMP_BOOL, \
+	.name = (_name), \
+	.signal_u8_read = (_read), \
+	.signal_u8_write = (_write), \
+}
+
+struct counter_available {
+	union {
+		const u32 *enums;
+		const char *const *strs;
+	};
+	size_t num_items;
+};
+
+#define DEFINE_COUNTER_AVAILABLE(_name, _enums) \
+	struct counter_available _name = { \
+		.enums = (_enums), \
+		.num_items = ARRAY_SIZE(_enums), \
+	}
+
+#define DEFINE_COUNTER_ENUM(_name, _strs) \
+	struct counter_available _name = { \
+		.strs = (_strs), \
+		.num_items = ARRAY_SIZE(_strs), \
+	}
+
+#define COUNTER_COMP_DEVICE_ENUM(_name, _get, _set, _available) \
+{ \
+	.type = COUNTER_COMP_ENUM, \
+	.name = (_name), \
+	.device_u32_read = (_get), \
+	.device_u32_write = (_set), \
+	.priv = &(_available), \
+}
+#define COUNTER_COMP_COUNT_ENUM(_name, _get, _set, _available) \
+{ \
+	.type = COUNTER_COMP_ENUM, \
+	.name = (_name), \
+	.count_u32_read = (_get), \
+	.count_u32_write = (_set), \
+	.priv = &(_available), \
+}
+#define COUNTER_COMP_SIGNAL_ENUM(_name, _get, _set, _available) \
+{ \
+	.type = COUNTER_COMP_ENUM, \
+	.name = (_name), \
+	.signal_u32_read = (_get), \
+	.signal_u32_write = (_set), \
+	.priv = &(_available), \
+}
+
+#define COUNTER_COMP_CEILING(_read, _write) \
+	COUNTER_COMP_COUNT_U64("ceiling", _read, _write)
+
+#define COUNTER_COMP_COUNT_MODE(_read, _write, _available) \
+{ \
+	.type = COUNTER_COMP_COUNT_MODE, \
+	.name = "count_mode", \
+	.count_u32_read = (_read), \
+	.count_u32_write = (_write), \
+	.priv = &(_available), \
+}
+
+#define COUNTER_COMP_DIRECTION(_read) \
+{ \
+	.type = COUNTER_COMP_COUNT_DIRECTION, \
+	.name = "direction", \
+	.count_u32_read = (_read), \
+}
+
+#define COUNTER_COMP_ENABLE(_read, _write) \
+	COUNTER_COMP_COUNT_BOOL("enable", _read, _write)
+
+#define COUNTER_COMP_FLOOR(_read, _write) \
+	COUNTER_COMP_COUNT_U64("floor", _read, _write)
+
+#define COUNTER_COMP_PRESET(_read, _write) \
+	COUNTER_COMP_COUNT_U64("preset", _read, _write)
+
+#define COUNTER_COMP_PRESET_ENABLE(_read, _write) \
+	COUNTER_COMP_COUNT_BOOL("preset_enable", _read, _write)
 
 #endif /* _COUNTER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cpu.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cpu.h
@@ -65,6 +65,17 @@
 extern ssize_t cpu_show_itlb_multihit(struct device *dev,
 				      struct device_attribute *attr, char *buf);
 extern ssize_t cpu_show_srbds(struct device *dev, struct device_attribute *attr, char *buf);
+extern ssize_t cpu_show_mmio_stale_data(struct device *dev,
+					struct device_attribute *attr,
+					char *buf);
+extern ssize_t cpu_show_retbleed(struct device *dev,
+				 struct device_attribute *attr, char *buf);
+extern ssize_t cpu_show_spec_rstack_overflow(struct device *dev,
+					     struct device_attribute *attr, char *buf);
+extern ssize_t cpu_show_gds(struct device *dev,
+			    struct device_attribute *attr, char *buf);
+extern ssize_t cpu_show_reg_file_data_sampling(struct device *dev,
+					       struct device_attribute *attr, char *buf);
 
 extern __printf(4, 5)
 struct device *cpu_device_create(struct device *parent, void *drvdata,
@@ -182,6 +193,12 @@
 void arch_cpu_idle_exit(void);
 void arch_cpu_idle_dead(void);
 
+#ifdef CONFIG_ARCH_HAS_CPU_FINALIZE_INIT
+void arch_cpu_finalize_init(void);
+#else
+static inline void arch_cpu_finalize_init(void) { }
+#endif
+
 int cpu_report_state(int cpu);
 int cpu_check_up_prepare(int cpu);
 void cpu_set_state_online(int cpu);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cpufreq.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cpufreq.h
@@ -643,6 +643,11 @@
 /* sysfs ops for cpufreq governors */
 extern const struct sysfs_ops governor_sysfs_ops;
 
+static inline struct gov_attr_set *to_gov_attr_set(struct kobject *kobj)
+{
+	return container_of(kobj, struct gov_attr_set, kobj);
+}
+
 void gov_attr_set_init(struct gov_attr_set *attr_set, struct list_head *list_node);
 void gov_attr_set_get(struct gov_attr_set *attr_set, struct list_head *list_node);
 unsigned int gov_attr_set_put(struct gov_attr_set *attr_set, struct list_head *list_node);
@@ -1041,7 +1046,7 @@
 		if (cpu == pcpu)
 			continue;
 
-		ret = parse_perf_domain(pcpu, list_name, cell_name);
+		ret = parse_perf_domain(cpu, list_name, cell_name);
 		if (ret < 0)
 			continue;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cpuhotplug.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cpuhotplug.h
@@ -99,6 +99,7 @@
 	CPUHP_LUSTRE_CFS_DEAD,
 	CPUHP_AP_ARM_CACHE_B15_RAC_DEAD,
 	CPUHP_PADATA_DEAD,
+	CPUHP_RANDOM_PREPARE,
 	CPUHP_WORKQUEUE_PREP,
 	CPUHP_POWER_NUMA_PREPARE,
 	CPUHP_HRTIMERS_PREPARE,
@@ -149,6 +150,7 @@
 	CPUHP_AP_IRQ_MIPS_GIC_STARTING,
 	CPUHP_AP_IRQ_RISCV_STARTING,
 	CPUHP_AP_IRQ_SIFIVE_PLIC_STARTING,
+	CPUHP_AP_IRQ_XILINX_STARTING,
 	CPUHP_AP_ARM_MVEBU_COHERENCY,
 	CPUHP_AP_MICROCODE_LOADER,
 	CPUHP_AP_PERF_X86_AMD_UNCORE_STARTING,
@@ -158,7 +160,6 @@
 	CPUHP_AP_PERF_X86_CSTATE_STARTING,
 	CPUHP_AP_PERF_XTENSA_STARTING,
 	CPUHP_AP_MIPS_OP_LOONGSON3_STARTING,
-	CPUHP_AP_ARM_SDEI_STARTING,
 	CPUHP_AP_ARM_VFP_STARTING,
 	CPUHP_AP_ARM64_DEBUG_MONITORS_STARTING,
 	CPUHP_AP_PERF_ARM_HW_BREAKPOINT_STARTING,
@@ -179,6 +180,7 @@
 	CPUHP_AP_RISCV_TIMER_STARTING,
 	CPUHP_AP_CLINT_TIMER_STARTING,
 	CPUHP_AP_CSKY_TIMER_STARTING,
+	CPUHP_AP_MICROBLAZE_TIMER_STARTING,
 	CPUHP_AP_TI_GP_TIMER_STARTING,
 	CPUHP_AP_HYPERV_TIMER_STARTING,
 	CPUHP_AP_KVM_STARTING,
@@ -188,10 +190,12 @@
 	/* Must be the last timer callback */
 	CPUHP_AP_DUMMY_TIMER_STARTING,
 	CPUHP_AP_ARM_XEN_STARTING,
+	CPUHP_AP_ARM_XEN_RUNSTATE_STARTING,
 	CPUHP_AP_ARM_CORESIGHT_STARTING,
 	CPUHP_AP_ARM_CORESIGHT_CTI_STARTING,
 	CPUHP_AP_ARM64_ISNDEP_STARTING,
 	CPUHP_AP_SMPCFD_DYING,
+	CPUHP_AP_HRTIMERS_DYING,
 	CPUHP_AP_X86_TBOOT_DYING,
 	CPUHP_AP_ARM_CACHE_B15_RAC_DYING,
 	CPUHP_AP_ONLINE,
@@ -238,6 +242,7 @@
 	CPUHP_AP_PERF_CSKY_ONLINE,
 	CPUHP_AP_WATCHDOG_ONLINE,
 	CPUHP_AP_WORKQUEUE_ONLINE,
+	CPUHP_AP_RANDOM_ONLINE,
 	CPUHP_AP_RCUTREE_ONLINE,
 	CPUHP_AP_BASE_CACHEINFO_ONLINE,
 	CPUHP_AP_ONLINE_DYN,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cpumask.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cpumask.h
@@ -667,7 +667,7 @@
  */
 static inline unsigned int cpumask_size(void)
 {
-	return BITS_TO_LONGS(nr_cpumask_bits) * sizeof(long);
+	return bitmap_size(nr_cpumask_bits);
 }
 
 /*
@@ -1045,4 +1045,23 @@
 	[0] =  1UL							\
 } }
 
+/*
+ * Provide a valid theoretical max size for cpumap and cpulist sysfs files
+ * to avoid breaking userspace which may allocate a buffer based on the size
+ * reported by e.g. fstat.
+ *
+ * for cpumap NR_CPUS * 9/32 - 1 should be an exact length.
+ *
+ * For cpulist 7 is (ceil(log10(NR_CPUS)) + 1) allowing for NR_CPUS to be up
+ * to 2 orders of magnitude larger than 8192. And then we divide by 2 to
+ * cover a worst-case of every other cpu being on one of two nodes for a
+ * very large NR_CPUS.
+ *
+ *  Use PAGE_SIZE as a minimum for smaller configurations while avoiding
+ *  unsigned comparison to -1.
+ */
+#define CPUMAP_FILE_MAX_BYTES  (((NR_CPUS * 9)/32 > PAGE_SIZE) \
+					? (NR_CPUS * 9)/32 - 1 : PAGE_SIZE)
+#define CPULIST_FILE_MAX_BYTES  (((NR_CPUS * 7)/2 > PAGE_SIZE) ? (NR_CPUS * 7)/2 : PAGE_SIZE)
+
 #endif /* __LINUX_CPUMASK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cpuset.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cpuset.h
@@ -56,8 +56,10 @@
 extern void cpuset_force_rebuild(void);
 extern void cpuset_update_active_cpus(void);
 extern void cpuset_wait_for_hotplug(void);
-extern void cpuset_read_lock(void);
-extern void cpuset_read_unlock(void);
+extern void inc_dl_tasks_cs(struct task_struct *task);
+extern void dec_dl_tasks_cs(struct task_struct *task);
+extern void cpuset_lock(void);
+extern void cpuset_unlock(void);
 extern void cpuset_cpus_allowed(struct task_struct *p, struct cpumask *mask);
 extern bool cpuset_cpus_allowed_fallback(struct task_struct *p);
 extern nodemask_t cpuset_mems_allowed(struct task_struct *p);
@@ -179,8 +181,10 @@
 
 static inline void cpuset_wait_for_hotplug(void) { }
 
-static inline void cpuset_read_lock(void) { }
-static inline void cpuset_read_unlock(void) { }
+static inline void inc_dl_tasks_cs(struct task_struct *task) { }
+static inline void dec_dl_tasks_cs(struct task_struct *task) { }
+static inline void cpuset_lock(void) { }
+static inline void cpuset_unlock(void) { }
 
 static inline void cpuset_cpus_allowed(struct task_struct *p,
 				       struct cpumask *mask)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/cred.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/cred.h
@@ -18,6 +18,7 @@
 
 struct cred;
 struct inode;
+struct lsmblob;
 
 /*
  * COW Supplementary groups list
@@ -108,7 +109,7 @@
  * same context as task->real_cred.
  */
 struct cred {
-	atomic_t	usage;
+	atomic_long_t	usage;
 #ifdef CONFIG_DEBUG_CREDENTIALS
 	atomic_t	subscribers;	/* number of processes subscribed */
 	void		*put_addr;
@@ -165,7 +166,7 @@
 extern void revert_creds(const struct cred *);
 extern struct cred *prepare_kernel_cred(struct task_struct *);
 extern int change_create_files_as(struct cred *, struct inode *);
-extern int set_security_override(struct cred *, u32);
+extern int set_security_override(struct cred *, struct lsmblob *);
 extern int set_security_override_from_ctx(struct cred *, const char *);
 extern int set_create_files_as(struct cred *, struct inode *);
 extern int cred_fscmp(const struct cred *, const struct cred *);
@@ -228,7 +229,7 @@
  */
 static inline struct cred *get_new_cred(struct cred *cred)
 {
-	atomic_inc(&cred->usage);
+	atomic_long_inc(&cred->usage);
 	return cred;
 }
 
@@ -260,7 +261,7 @@
 	struct cred *nonconst_cred = (struct cred *) cred;
 	if (!cred)
 		return NULL;
-	if (!atomic_inc_not_zero(&nonconst_cred->usage))
+	if (!atomic_long_inc_not_zero(&nonconst_cred->usage))
 		return NULL;
 	validate_creds(cred);
 	nonconst_cred->non_rcu = 0;
@@ -284,7 +285,7 @@
 
 	if (cred) {
 		validate_creds(cred);
-		if (atomic_dec_and_test(&(cred)->usage))
+		if (atomic_long_dec_and_test(&(cred)->usage))
 			__put_cred(cred);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/crypto.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/crypto.h
@@ -167,6 +167,7 @@
 struct crypto_tfm;
 struct crypto_type;
 
+typedef struct crypto_async_request crypto_completion_data_t;
 typedef void (*crypto_completion_t)(struct crypto_async_request *req, int err);
 
 /**
@@ -586,6 +587,11 @@
 /*
  * Async ops completion helper functioons
  */
+static inline void *crypto_get_completion_data(crypto_completion_data_t *req)
+{
+	return req->data;
+}
+
 void crypto_req_done(struct crypto_async_request *req, int err);
 
 static inline int crypto_wait_req(int err, struct crypto_wait *wait)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/debugfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/debugfs.h
@@ -45,7 +45,7 @@
 
 extern struct dentry *arch_debugfs_dir;
 
-#define DEFINE_DEBUGFS_ATTRIBUTE(__fops, __get, __set, __fmt)		\
+#define DEFINE_DEBUGFS_ATTRIBUTE_XSIGNED(__fops, __get, __set, __fmt, __is_signed)	\
 static int __fops ## _open(struct inode *inode, struct file *file)	\
 {									\
 	__simple_attr_check_format(__fmt, 0ull);			\
@@ -56,10 +56,16 @@
 	.open	 = __fops ## _open,					\
 	.release = simple_attr_release,					\
 	.read	 = debugfs_attr_read,					\
-	.write	 = debugfs_attr_write,					\
+	.write	 = (__is_signed) ? debugfs_attr_write_signed : debugfs_attr_write,	\
 	.llseek  = no_llseek,						\
 }
 
+#define DEFINE_DEBUGFS_ATTRIBUTE(__fops, __get, __set, __fmt)		\
+	DEFINE_DEBUGFS_ATTRIBUTE_XSIGNED(__fops, __get, __set, __fmt, false)
+
+#define DEFINE_DEBUGFS_ATTRIBUTE_SIGNED(__fops, __get, __set, __fmt)	\
+	DEFINE_DEBUGFS_ATTRIBUTE_XSIGNED(__fops, __get, __set, __fmt, true)
+
 typedef struct vfsmount *(*debugfs_automount_t)(struct dentry *, void *);
 
 #if defined(CONFIG_DEBUG_FS)
@@ -91,6 +97,8 @@
 void debugfs_remove(struct dentry *dentry);
 #define debugfs_remove_recursive debugfs_remove
 
+void debugfs_lookup_and_remove(const char *name, struct dentry *parent);
+
 const struct file_operations *debugfs_real_fops(const struct file *filp);
 
 int debugfs_file_get(struct dentry *dentry);
@@ -100,6 +108,8 @@
 			size_t len, loff_t *ppos);
 ssize_t debugfs_attr_write(struct file *file, const char __user *buf,
 			size_t len, loff_t *ppos);
+ssize_t debugfs_attr_write_signed(struct file *file, const char __user *buf,
+			size_t len, loff_t *ppos);
 
 struct dentry *debugfs_rename(struct dentry *old_dir, struct dentry *old_dentry,
                 struct dentry *new_dir, const char *new_name);
@@ -225,6 +235,10 @@
 static inline void debugfs_remove_recursive(struct dentry *dentry)
 { }
 
+static inline void debugfs_lookup_and_remove(const char *name,
+					     struct dentry *parent)
+{ }
+
 const struct file_operations *debugfs_real_fops(const struct file *filp);
 
 static inline int debugfs_file_get(struct dentry *dentry)
@@ -245,6 +259,13 @@
 					const char __user *buf,
 					size_t len, loff_t *ppos)
 {
+	return -ENODEV;
+}
+
+static inline ssize_t debugfs_attr_write_signed(struct file *file,
+					const char __user *buf,
+					size_t len, loff_t *ppos)
+{
 	return -ENODEV;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/delay.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/delay.h
@@ -20,6 +20,7 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/sched.h>
 
 extern unsigned long loops_per_jiffy;
 
@@ -58,7 +59,18 @@
 void __attribute__((weak)) calibration_delay_done(void);
 void msleep(unsigned int msecs);
 unsigned long msleep_interruptible(unsigned int msecs);
-void usleep_range(unsigned long min, unsigned long max);
+void usleep_range_state(unsigned long min, unsigned long max,
+			unsigned int state);
+
+static inline void usleep_range(unsigned long min, unsigned long max)
+{
+	usleep_range_state(min, max, TASK_UNINTERRUPTIBLE);
+}
+
+static inline void usleep_idle_range(unsigned long min, unsigned long max)
+{
+	usleep_range_state(min, max, TASK_IDLE);
+}
 
 static inline void ssleep(unsigned int seconds)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dev_printk.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dev_printk.h
@@ -130,6 +130,16 @@
 	})
 
 /*
+ * Dummy dev_printk for disabled debugging statements to use whilst maintaining
+ * gcc's format checking.
+ */
+#define dev_no_printk(level, dev, fmt, ...)				\
+	({								\
+		if (0)							\
+			_dev_printk(level, dev, fmt, ##__VA_ARGS__);	\
+	})
+
+/*
  * #defines for all the dev_<level> macros to prefix with whatever
  * possible use of #define dev_fmt(fmt) ...
  */
@@ -158,10 +168,7 @@
 	dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__)
 #else
 #define dev_dbg(dev, fmt, ...)						\
-({									\
-	if (0)								\
-		dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
-})
+	dev_no_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__)
 #endif
 
 #ifdef CONFIG_PRINTK
@@ -247,20 +254,14 @@
 } while (0)
 #else
 #define dev_dbg_ratelimited(dev, fmt, ...)				\
-do {									\
-	if (0)								\
-		dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
-} while (0)
+	dev_no_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__)
 #endif
 
 #ifdef VERBOSE_DEBUG
 #define dev_vdbg	dev_dbg
 #else
 #define dev_vdbg(dev, fmt, ...)						\
-({									\
-	if (0)								\
-		dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
-})
+	dev_no_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__)
 #endif
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/devfreq.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/devfreq.h
@@ -149,8 +149,8 @@
  * @work:	delayed work for load monitoring.
  * @previous_freq:	previously configured frequency value.
  * @last_status:	devfreq user device info, performance statistics
- * @data:	Private data of the governor. The devfreq framework does not
- *		touch this.
+ * @data:	devfreq driver pass to governors, governor should not change it.
+ * @governor_data:	private data for governors, devfreq core doesn't touch it.
  * @user_min_freq_req:	PM QoS minimum frequency request from user (via sysfs)
  * @user_max_freq_req:	PM QoS maximum frequency request from user (via sysfs)
  * @scaling_min_freq:	Limit minimum frequency requested by OPP interface
@@ -187,7 +187,8 @@
 	unsigned long previous_freq;
 	struct devfreq_dev_status last_status;
 
-	void *data; /* private data for governors */
+	void *data;
+	void *governor_data;
 
 	struct dev_pm_qos_request user_min_freq_req;
 	struct dev_pm_qos_request user_max_freq_req;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/device.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/device.h
@@ -830,6 +830,8 @@
 				 int (*match)(struct device *dev, void *data));
 struct device *device_find_child_by_name(struct device *parent,
 					 const char *name);
+struct device *device_find_any_child(struct device *parent);
+
 int device_rename(struct device *dev, const char *new_name);
 int device_move(struct device *dev, struct device *new_parent,
 		enum dpm_order dpm_order);
@@ -971,6 +973,7 @@
 void device_link_remove(void *consumer, struct device *supplier);
 void device_links_supplier_sync_state_pause(void);
 void device_links_supplier_sync_state_resume(void);
+void device_link_wait_removal(void);
 
 extern __printf(3, 4)
 int dev_err_probe(const struct device *dev, int err, const char *fmt, ...);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/device/driver.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/device/driver.h
@@ -150,6 +150,8 @@
 extern void driver_remove_file(struct device_driver *driver,
 			       const struct driver_attribute *attr);
 
+int driver_set_override(struct device *dev, const char **override,
+			const char *s, size_t len);
 extern int __must_check driver_for_each_device(struct device_driver *drv,
 					       struct device *start,
 					       void *data,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dim.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dim.h
@@ -21,7 +21,7 @@
  * We consider 10% difference as significant.
  */
 #define IS_SIGNIFICANT_DIFF(val, ref) \
-	(((100UL * abs((val) - (ref))) / (ref)) > 10)
+	((ref) && (((100UL * abs((val) - (ref))) / (ref)) > 10))
 
 /*
  * Calculate the gap between two values.
@@ -236,8 +236,9 @@
  *
  * Calculate the delta between two samples (in data rates).
  * Takes into consideration counter wrap-around.
+ * Returned boolean indicates whether curr_stats are reliable.
  */
-void dim_calc_stats(struct dim_sample *start, struct dim_sample *end,
+bool dim_calc_stats(struct dim_sample *start, struct dim_sample *end,
 		    struct dim_stats *curr_stats);
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dma-buf.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dma-buf.h
@@ -433,7 +433,7 @@
 		wait_queue_head_t *poll;
 
 		__poll_t active;
-	} cb_excl, cb_shared;
+	} cb_in, cb_out;
 #ifdef CONFIG_DMABUF_SYSFS_STATS
 	/**
 	 * @sysfs_entry:
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dma-fence.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dma-fence.h
@@ -551,6 +551,25 @@
 	fence->error = error;
 }
 
+/**
+ * dma_fence_timestamp - helper to get the completion timestamp of a fence
+ * @fence: fence to get the timestamp from.
+ *
+ * After a fence is signaled the timestamp is updated with the signaling time,
+ * but setting the timestamp can race with tasks waiting for the signaling. This
+ * helper busy waits for the correct timestamp to appear.
+ */
+static inline ktime_t dma_fence_timestamp(struct dma_fence *fence)
+{
+	if (WARN_ON(!test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags)))
+		return ktime_get();
+
+	while (!test_bit(DMA_FENCE_FLAG_TIMESTAMP_BIT, &fence->flags))
+		cpu_relax();
+
+	return fence->timestamp;
+}
+
 signed long dma_fence_wait_timeout(struct dma_fence *,
 				   bool intr, signed long timeout);
 signed long dma_fence_wait_any_timeout(struct dma_fence **fences,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dma-map-ops.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dma-map-ops.h
@@ -69,6 +69,7 @@
 	int (*dma_supported)(struct device *dev, u64 mask);
 	u64 (*get_required_mask)(struct device *dev);
 	size_t (*max_mapping_size)(struct device *dev);
+	size_t (*opt_mapping_size)(void);
 	unsigned long (*get_merge_boundary)(struct device *dev);
 };
 
@@ -166,6 +167,7 @@
 #ifdef CONFIG_DMA_DECLARE_COHERENT
 int dma_declare_coherent_memory(struct device *dev, phys_addr_t phys_addr,
 		dma_addr_t device_addr, size_t size);
+void dma_release_coherent_memory(struct device *dev);
 int dma_alloc_from_dev_coherent(struct device *dev, ssize_t size,
 		dma_addr_t *dma_handle, void **ret);
 int dma_release_from_dev_coherent(struct device *dev, int order, void *vaddr);
@@ -177,9 +179,11 @@
 {
 	return -ENOSYS;
 }
+
 #define dma_alloc_from_dev_coherent(dev, size, handle, ret) (0)
 #define dma_release_from_dev_coherent(dev, order, vaddr) (0)
 #define dma_mmap_from_dev_coherent(dev, vma, vaddr, order, ret) (0)
+static inline void dma_release_coherent_memory(struct device *dev) { }
 #endif /* CONFIG_DMA_DECLARE_COHERENT */
 
 #ifdef CONFIG_DMA_GLOBAL_POOL
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dma-mapping.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dma-mapping.h
@@ -144,6 +144,7 @@
 int dma_set_coherent_mask(struct device *dev, u64 mask);
 u64 dma_get_required_mask(struct device *dev);
 size_t dma_max_mapping_size(struct device *dev);
+size_t dma_opt_mapping_size(struct device *dev);
 bool dma_need_sync(struct device *dev, dma_addr_t dma_addr);
 unsigned long dma_get_merge_boundary(struct device *dev);
 struct sg_table *dma_alloc_noncontiguous(struct device *dev, size_t size,
@@ -266,6 +267,10 @@
 {
 	return 0;
 }
+static inline size_t dma_opt_mapping_size(struct device *dev)
+{
+	return 0;
+}
 static inline bool dma_need_sync(struct device *dev, dma_addr_t dma_addr)
 {
 	return false;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dma/xilinx_frmbuf.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dma/xilinx_frmbuf.h
@@ -0,0 +1,258 @@
+/*
+ * Xilinx Framebuffer DMA support header file
+ *
+ * Copyright (C) 2017 Xilinx, Inc. All rights reserved.
+ *
+ * This is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __XILINX_FRMBUF_DMA_H
+#define __XILINX_FRMBUF_DMA_H
+
+#include <linux/dmaengine.h>
+
+/* Modes to enable early callback */
+/* To avoid first frame delay */
+#define EARLY_CALLBACK			BIT(1)
+/* Give callback at start of descriptor processing */
+#define EARLY_CALLBACK_START_DESC	BIT(2)
+/**
+ * enum vid_frmwork_type - Linux video framework type
+ * @XDMA_DRM: fourcc is of type DRM
+ * @XDMA_V4L2: fourcc is of type V4L2
+ */
+enum vid_frmwork_type {
+	XDMA_DRM = 0,
+	XDMA_V4L2,
+};
+
+/**
+ * enum operation_mode - FB IP control register field settings to select mode
+ * @DEFAULT : Use default mode, No explicit bit field settings required.
+ * @AUTO_RESTART : Use auto-restart mode by setting BIT(7) of control register.
+ */
+enum operation_mode {
+	DEFAULT = 0x0,
+	AUTO_RESTART = BIT(7),
+};
+
+/**
+ * enum fid_modes - FB IP fid mode register settings to select mode
+ * @FID_MODE_0: carries the fid value shared by application
+ * @FID_MODE_1: sets the fid after first frame
+ * @FID_MODE_2: sets the fid after second frame
+ */
+enum fid_modes {
+	FID_MODE_0 = 0,
+	FID_MODE_1 = 1,
+	FID_MODE_2 = 2,
+};
+
+#if IS_ENABLED(CONFIG_XILINX_FRMBUF)
+/**
+ * xilinx_xdma_set_mode - Set operation mode for framebuffer IP
+ * @chan: dma channel instance
+ * @mode: Famebuffer IP operation mode.
+ * This routine is used when utilizing "video format aware" Xilinx DMA IP
+ * (such as Video Framebuffer Read or Video Framebuffer Write).  This call
+ * must be made prior to dma_async_issue_pending(). This routine should be
+ * called by client driver to set the operation mode for framebuffer IP based
+ * upon the use-case, for e.g. for non-streaming usecases (like MEM2MEM) it's
+ * more appropriate to use default mode unlike streaming usecases where
+ * auto-restart mode is more suitable.
+ *
+ * auto-restart or free running mode.
+ */
+void xilinx_xdma_set_mode(struct dma_chan *chan, enum operation_mode mode);
+
+/**
+ * xilinx_xdma_drm_config - configure video format in video aware DMA
+ * @chan: dma channel instance
+ * @drm_fourcc: DRM fourcc code describing the memory layout of video data
+ *
+ * This routine is used when utilizing "video format aware" Xilinx DMA IP
+ * (such as Video Framebuffer Read or Video Framebuffer Write).  This call
+ * must be made prior to dma_async_issue_pending() to establish the video
+ * data memory format within the hardware DMA.
+ */
+void xilinx_xdma_drm_config(struct dma_chan *chan, u32 drm_fourcc);
+
+/**
+ * xilinx_xdma_v4l2_config - configure video format in video aware DMA
+ * @chan: dma channel instance
+ * @v4l2_fourcc: V4L2 fourcc code describing the memory layout of video data
+ *
+ * This routine is used when utilizing "video format aware" Xilinx DMA IP
+ * (such as Video Framebuffer Read or Video Framebuffer Write).  This call
+ * must be made prior to dma_async_issue_pending() to establish the video
+ * data memory format within the hardware DMA.
+ */
+void xilinx_xdma_v4l2_config(struct dma_chan *chan, u32 v4l2_fourcc);
+
+/**
+ * xilinx_xdma_get_drm_vid_fmts - obtain list of supported DRM mem formats
+ * @chan: dma channel instance
+ * @fmt_cnt: Output param - total count of supported DRM fourcc codes
+ * @fmts: Output param - pointer to array of DRM fourcc codes (not a copy)
+ *
+ * Return: a reference to an array of DRM fourcc codes supported by this
+ * instance of the Video Framebuffer Driver
+ */
+int xilinx_xdma_get_drm_vid_fmts(struct dma_chan *chan, u32 *fmt_cnt,
+				 u32 **fmts);
+
+/**
+ * xilinx_xdma_get_v4l2_vid_fmts - obtain list of supported V4L2 mem formats
+ * @chan: dma channel instance
+ * @fmt_cnt: Output param - total count of supported V4L2 fourcc codes
+ * @fmts: Output param - pointer to array of V4L2 fourcc codes (not a copy)
+ *
+ * Return: a reference to an array of V4L2 fourcc codes supported by this
+ * instance of the Video Framebuffer Driver
+ */
+int xilinx_xdma_get_v4l2_vid_fmts(struct dma_chan *chan, u32 *fmt_cnt,
+				  u32 **fmts);
+
+/**
+ * xilinx_xdma_get_fid - Get the Field ID of the buffer received.
+ * This function should be called from the callback function registered
+ * per descriptor in prep_interleaved.
+ *
+ * @chan: dma channel instance
+ * @async_tx: descriptor whose parent structure contains fid.
+ * @fid: Output param - Field ID of the buffer. 0 - even, 1 - odd.
+ *
+ * Return: 0 on success, -EINVAL in case of invalid chan
+ */
+int xilinx_xdma_get_fid(struct dma_chan *chan,
+			struct dma_async_tx_descriptor *async_tx, u32 *fid);
+
+/**
+ * xilinx_xdma_set_fid - Set the Field ID of the buffer to be transmitted
+ * @chan: dma channel instance
+ * @async_tx: dma async tx descriptor for the buffer
+ * @fid: Field ID of the buffer. 0 - even, 1 - odd.
+ *
+ * Return: 0 on success, -EINVAL in case of invalid chan
+ */
+int xilinx_xdma_set_fid(struct dma_chan *chan,
+			struct dma_async_tx_descriptor *async_tx, u32 fid);
+
+/**
+ * xilinx_xdma_get_fid_err_flag - Get the Field ID error flag.
+ *
+ * @chan: dma channel instance
+ * @fid_err_flag: Field id error detect flag. 0 - no error, 1 - error.
+ *
+ * Return: 0 on success, -EINVAL in case of invalid chan
+ */
+int xilinx_xdma_get_fid_err_flag(struct dma_chan *chan,
+				 u32 *fid_err_flag);
+
+/**
+ * xilinx_xdma_get_fid_out - Get the Field ID out signal value.
+ *
+ * @chan: dma channel instance
+ * @fid_out_val: Field id out signal value.
+ *
+ * Return: 0 on success, -EINVAL in case of invalid chan
+ */
+int xilinx_xdma_get_fid_out(struct dma_chan *chan,
+			    u32 *fid_out_val);
+
+/**:
+ * xilinx_xdma_get_earlycb - Get info if early callback has been enabled.
+ *
+ * @chan: dma channel instance
+ * @async_tx: descriptor whose parent structure contains fid.
+ * @earlycb: Output param - Early callback mode
+ *
+ * Return: 0 on success, -EINVAL in case of invalid chan
+ */
+int xilinx_xdma_get_earlycb(struct dma_chan *chan,
+			    struct dma_async_tx_descriptor *async_tx,
+			    u32 *earlycb);
+
+/**
+ * xilinx_xdma_set_earlycb - Enable/Disable early callback
+ * @chan: dma channel instance
+ * @async_tx: dma async tx descriptor for the buffer
+ * @earlycb: Enable early callback mode for descriptor
+ *
+ * Return: 0 on success, -EINVAL in case of invalid chan
+ */
+int xilinx_xdma_set_earlycb(struct dma_chan *chan,
+			    struct dma_async_tx_descriptor *async_tx,
+			    u32 earlycb);
+/**
+ * xilinx_xdma_get_width_align - Get width alignment value
+ *
+ * @chan: dma channel instance
+ * @width_align: width alignment value
+ *
+ * Return: 0 on success, -ENODEV in case no framebuffer device found
+ */
+int xilinx_xdma_get_width_align(struct dma_chan *chan, u32 *width_align);
+
+#else
+static inline void xilinx_xdma_set_mode(struct dma_chan *chan,
+					enum operation_mode mode)
+{ }
+
+static inline void xilinx_xdma_drm_config(struct dma_chan *chan, u32 drm_fourcc)
+{ }
+
+static inline void xilinx_xdma_v4l2_config(struct dma_chan *chan,
+					   u32 v4l2_fourcc)
+{ }
+
+static inline int xilinx_xdma_get_drm_vid_fmts(struct dma_chan *chan,
+					       u32 *fmt_cnt, u32 **fmts)
+{
+	return -ENODEV;
+}
+
+static inline int xilinx_xdma_get_v4l2_vid_fmts(struct dma_chan *chan,
+						u32 *fmt_cnt,u32 **fmts)
+{
+	return -ENODEV;
+}
+
+static inline int xilinx_xdma_get_fid(struct dma_chan *chan,
+				      struct dma_async_tx_descriptor *async_tx,
+				      u32 *fid)
+{
+	return -ENODEV;
+}
+
+static inline int xilinx_xdma_set_fid(struct dma_chan *chan,
+				      struct dma_async_tx_descriptor *async_tx,
+				      u32 fid)
+{
+	return -ENODEV;
+}
+
+static inline int xilinx_xdma_get_earlycb(struct dma_chan *chan,
+					  struct dma_async_tx_descriptor *atx,
+					  u32 *earlycb)
+{
+	return -ENODEV;
+}
+
+static inline int xilinx_xdma_set_earlycb(struct dma_chan *chan,
+					  struct dma_async_tx_descriptor *atx,
+					  u32 earlycb)
+{
+	return -ENODEV;
+}
+
+static inline int xilinx_xdma_get_width_align(struct dma_chan *chan, u32 *width_align)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /*__XILINX_FRMBUF_DMA_H*/
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dmaengine.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dmaengine.h
@@ -944,10 +944,8 @@
 	void (*device_issue_pending)(struct dma_chan *chan);
 	void (*device_release)(struct dma_device *dev);
 	/* debugfs support */
-#ifdef CONFIG_DEBUG_FS
 	void (*dbg_summary_show)(struct seq_file *s, struct dma_device *dev);
 	struct dentry *dbg_dev_root;
-#endif
 };
 
 static inline int dmaengine_slave_config(struct dma_chan *chan,
@@ -961,7 +959,8 @@
 
 static inline bool is_slave_direction(enum dma_transfer_direction direction)
 {
-	return (direction == DMA_MEM_TO_DEV) || (direction == DMA_DEV_TO_MEM);
+	return (direction == DMA_MEM_TO_DEV) || (direction == DMA_DEV_TO_MEM) ||
+	       (direction == DMA_DEV_TO_DEV);
 }
 
 static inline struct dma_async_tx_descriptor *dmaengine_prep_slave_single(
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dnotify.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dnotify.h
@@ -26,7 +26,7 @@
 			    FS_MODIFY | FS_MODIFY_CHILD |\
 			    FS_ACCESS | FS_ACCESS_CHILD |\
 			    FS_ATTRIB | FS_ATTRIB_CHILD |\
-			    FS_CREATE | FS_DN_RENAME |\
+			    FS_CREATE | FS_RENAME |\
 			    FS_MOVED_FROM | FS_MOVED_TO)
 
 extern int dir_notify_enable;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dsa/ocelot.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dsa/ocelot.h
@@ -12,6 +12,7 @@
 struct ocelot_skb_cb {
 	struct sk_buff *clone;
 	unsigned int ptp_class; /* valid only for clones */
+	u32 tstamp_lo;
 	u8 ptp_cmd;
 	u8 ts_id;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/dynamic_debug.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/dynamic_debug.h
@@ -55,9 +55,6 @@
 
 #if defined(CONFIG_DYNAMIC_DEBUG_CORE)
 
-/* exported for module authors to exercise >control */
-int dynamic_debug_exec_queries(const char *query, const char *modname);
-
 int ddebug_add_module(struct _ddebug *tab, unsigned int n,
 				const char *modname);
 extern int ddebug_remove_module(const char *mod_name);
@@ -201,7 +198,7 @@
 static inline int ddebug_dyndbg_module_param_cb(char *param, char *val,
 						const char *modname)
 {
-	if (strstr(param, "dyndbg")) {
+	if (!strcmp(param, "dyndbg")) {
 		/* avoid pr_warn(), which wants pr_fmt() fully defined */
 		printk(KERN_WARNING "dyndbg param is supported only in "
 			"CONFIG_DYNAMIC_DEBUG builds\n");
@@ -221,12 +218,6 @@
 				rowsize, groupsize, buf, len, ascii);	\
 	} while (0)
 
-static inline int dynamic_debug_exec_queries(const char *query, const char *modname)
-{
-	pr_warn("kernel not built with CONFIG_DYNAMIC_DEBUG_CORE\n");
-	return 0;
-}
-
 #endif /* !CONFIG_DYNAMIC_DEBUG_CORE */
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/edac.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/edac.h
@@ -182,6 +182,8 @@
  * @MEM_LRDDR4:		Load-Reduced DDR4 memory.
  * @MEM_LPDDR4:		Low-Power DDR4 memory.
  * @MEM_DDR5:		Unbuffered DDR5 RAM
+ * @MEM_RDDR5:		Registered DDR5 RAM
+ * @MEM_LRDDR5:		Load-Reduced DDR5 memory.
  * @MEM_NVDIMM:		Non-volatile RAM
  * @MEM_WIO2:		Wide I/O 2.
  * @MEM_HBM2:		High bandwidth Memory Gen 2.
@@ -211,6 +213,8 @@
 	MEM_LRDDR4,
 	MEM_LPDDR4,
 	MEM_DDR5,
+	MEM_RDDR5,
+	MEM_LRDDR5,
 	MEM_NVDIMM,
 	MEM_WIO2,
 	MEM_HBM2,
@@ -239,6 +243,8 @@
 #define MEM_FLAG_LRDDR4         BIT(MEM_LRDDR4)
 #define MEM_FLAG_LPDDR4         BIT(MEM_LPDDR4)
 #define MEM_FLAG_DDR5           BIT(MEM_DDR5)
+#define MEM_FLAG_RDDR5          BIT(MEM_RDDR5)
+#define MEM_FLAG_LRDDR5         BIT(MEM_LRDDR5)
 #define MEM_FLAG_NVDIMM         BIT(MEM_NVDIMM)
 #define MEM_FLAG_WIO2		BIT(MEM_WIO2)
 #define MEM_FLAG_HBM2		BIT(MEM_HBM2)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/eeprom_93cx6.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/eeprom_93cx6.h
@@ -11,6 +11,8 @@
 	Supported chipsets: 93c46, 93c56 and 93c66.
  */
 
+#include <linux/bits.h>
+
 /*
  * EEPROM operation defines.
  */
@@ -34,6 +36,7 @@
  * @register_write(struct eeprom_93cx6 *eeprom): handler to
  * write to the eeprom register by using all reg_* fields.
  * @width: eeprom width, should be one of the PCI_EEPROM_WIDTH_* defines
+ * @quirks: eeprom or controller quirks
  * @drive_data: Set if we're driving the data line.
  * @reg_data_in: register field to indicate data input
  * @reg_data_out: register field to indicate data output
@@ -50,6 +53,9 @@
 	void (*register_write)(struct eeprom_93cx6 *eeprom);
 
 	int width;
+	unsigned int quirks;
+/* Some EEPROMs require an extra clock cycle before reading */
+#define PCI_EEPROM_QUIRK_EXTRA_READ_CYCLE	BIT(0)
 
 	char drive_data;
 	char reg_data_in;
@@ -71,3 +77,8 @@
 
 extern void eeprom_93cx6_write(struct eeprom_93cx6 *eeprom,
 			       u8 addr, u16 data);
+
+static inline bool has_quirk_extra_read_cycle(struct eeprom_93cx6 *eeprom)
+{
+	return eeprom->quirks & PCI_EEPROM_QUIRK_EXTRA_READ_CYCLE;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/efi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/efi.h
@@ -43,6 +43,8 @@
 #define EFI_ABORTED		(21 | (1UL << (BITS_PER_LONG-1)))
 #define EFI_SECURITY_VIOLATION	(26 | (1UL << (BITS_PER_LONG-1)))
 
+#define EFI_IS_ERROR(x)		((x) & (1UL << (BITS_PER_LONG-1)))
+
 typedef unsigned long efi_status_t;
 typedef u8 efi_bool_t;
 typedef u16 efi_char16_t;		/* UNICODE character */
@@ -125,6 +127,7 @@
 #define EFI_MEMORY_RO		((u64)0x0000000000020000ULL)	/* read-only */
 #define EFI_MEMORY_SP		((u64)0x0000000000040000ULL)	/* soft reserved */
 #define EFI_MEMORY_CPU_CRYPTO	((u64)0x0000000000080000ULL)	/* supports encryption */
+#define EFI_MEMORY_HOT_PLUGGABLE	BIT_ULL(20)	/* supports unplugging at runtime */
 #define EFI_MEMORY_RUNTIME	((u64)0x8000000000000000ULL)	/* range requires runtime mapping */
 #define EFI_MEMORY_DESCRIPTOR_VERSION	1
 
@@ -167,6 +170,8 @@
 	size_t			page_bytes_remain;
 };
 
+int efi_capsule_setup_info(struct capsule_info *cap_info, void *kbuff,
+                           size_t hdr_bytes);
 int __efi_capsule_setup_info(struct capsule_info *cap_info);
 
 /*
@@ -625,18 +630,10 @@
 #endif
 extern void __iomem *efi_lookup_mapped_addr(u64 phys_addr);
 
-extern int __init efi_memmap_alloc(unsigned int num_entries,
-				   struct efi_memory_map_data *data);
-extern void __efi_memmap_free(u64 phys, unsigned long size,
-			      unsigned long flags);
+extern int __init __efi_memmap_init(struct efi_memory_map_data *data);
 extern int __init efi_memmap_init_early(struct efi_memory_map_data *data);
 extern int __init efi_memmap_init_late(phys_addr_t addr, unsigned long size);
 extern void __init efi_memmap_unmap(void);
-extern int __init efi_memmap_install(struct efi_memory_map_data *data);
-extern int __init efi_memmap_split_count(efi_memory_desc_t *md,
-					 struct range *range);
-extern void __init efi_memmap_insert(struct efi_memory_map *old_memmap,
-				     void *buf, struct efi_mem_range *mem);
 
 #ifdef CONFIG_EFI_ESRT
 extern void __init efi_esrt_init(void);
@@ -782,6 +779,23 @@
 #define EFI_MEM_ATTR		10	/* Did firmware publish an EFI_MEMORY_ATTRIBUTES table? */
 #define EFI_MEM_NO_SOFT_RESERVE	11	/* Is the kernel configured to ignore soft reservations? */
 #define EFI_PRESERVE_BS_REGIONS	12	/* Are EFI boot-services memory segments available? */
+#define EFI_SECURE_BOOT		13	/* Are we in Secure Boot mode? */
+
+enum efi_secureboot_mode {
+	efi_secureboot_mode_unset,
+	efi_secureboot_mode_unknown,
+	efi_secureboot_mode_disabled,
+	efi_secureboot_mode_enabled,
+};
+
+#ifdef CONFIG_EFI_PARAMS_FROM_FDT
+u32 __init efi_get__secure_boot(void);
+#else
+static inline u32 efi_get__secure_boot(void)
+{
+	return efi_secureboot_mode_unset;
+};
+#endif
 
 #ifdef CONFIG_EFI
 /*
@@ -793,6 +807,8 @@
 }
 extern void efi_reboot(enum reboot_mode reboot_mode, const char *__unused);
 
+extern void __init efi_set_secure_boot(enum efi_secureboot_mode mode);
+
 bool __pure __efi_soft_reserve_enabled(void);
 
 static inline bool __pure efi_soft_reserve_enabled(void)
@@ -813,6 +829,8 @@
 static inline void
 efi_reboot(enum reboot_mode reboot_mode, const char *__unused) {}
 
+static inline void efi_set_secure_boot(enum efi_secureboot_mode mode) {}
+
 static inline bool efi_soft_reserve_enabled(void)
 {
 	return false;
@@ -825,6 +843,7 @@
 #endif
 
 extern int efi_status_to_err(efi_status_t status);
+extern const char *efi_status_to_str(efi_status_t status);
 
 /*
  * Variable Attributes
@@ -1077,13 +1096,6 @@
 extern void efi_call_virt_check_flags(unsigned long flags, const char *call);
 extern unsigned long efi_call_virt_save_flags(void);
 
-enum efi_secureboot_mode {
-	efi_secureboot_mode_unset,
-	efi_secureboot_mode_unknown,
-	efi_secureboot_mode_disabled,
-	efi_secureboot_mode_enabled,
-};
-
 static inline
 enum efi_secureboot_mode efi_get_secureboot_mode(efi_get_variable_t *get_var)
 {
@@ -1112,8 +1124,6 @@
 static inline void efi_check_for_embedded_firmwares(void) { }
 #endif
 
-efi_status_t efi_random_get_seed(void);
-
 /*
  * Arch code can implement the following three template macros, avoiding
  * reptition for the void/non-void return cases of {__,}efi_call_virt():
@@ -1163,7 +1173,7 @@
 	arch_efi_call_virt_teardown();					\
 })
 
-#define EFI_RANDOM_SEED_SIZE		64U
+#define EFI_RANDOM_SEED_SIZE		32U // BLAKE2S_HASH_SIZE
 
 struct linux_efi_random_seed {
 	u32	size;
@@ -1282,4 +1292,10 @@
 }
 #endif
 
+#ifdef CONFIG_SYSFB
+extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
+#else
+static inline void efifb_setup_from_dmi(struct screen_info *si, const char *opt) { }
+#endif
+
 #endif /* _LINUX_EFI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/entry-kvm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/entry-kvm.h
@@ -75,7 +75,7 @@
  */
 static inline bool __xfer_to_guest_mode_work_pending(void)
 {
-	unsigned long ti_work = READ_ONCE(current_thread_info()->flags);
+	unsigned long ti_work = read_thread_flags();
 
 	return !!(ti_work & XFER_TO_GUEST_MODE_WORK);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/etherdevice.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/etherdevice.h
@@ -127,7 +127,7 @@
 #endif
 }
 
-static inline bool is_multicast_ether_addr_64bits(const u8 addr[6+2])
+static inline bool is_multicast_ether_addr_64bits(const u8 *addr)
 {
 #if defined(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS) && BITS_PER_LONG == 64
 #ifdef __BIG_ENDIAN
@@ -323,7 +323,7 @@
 				       struct net_device *src)
 {
 	dst->addr_assign_type = src->addr_assign_type;
-	ether_addr_copy(dst->dev_addr, src->dev_addr);
+	eth_hw_addr_set(dst, src->dev_addr);
 }
 
 /**
@@ -364,8 +364,7 @@
  * Please note that alignment of addr1 & addr2 are only guaranteed to be 16 bits.
  */
 
-static inline bool ether_addr_equal_64bits(const u8 addr1[6+2],
-					   const u8 addr2[6+2])
+static inline bool ether_addr_equal_64bits(const u8 *addr1, const u8 *addr2)
 {
 #if defined(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS) && BITS_PER_LONG == 64
 	u64 fold = (*(const u64 *)addr1) ^ (*(const u64 *)addr2);
@@ -544,6 +543,31 @@
 }
 
 /**
+ * eth_skb_pkt_type - Assign packet type if destination address does not match
+ * @skb: Assigned a packet type if address does not match @dev address
+ * @dev: Network device used to compare packet address against
+ *
+ * If the destination MAC address of the packet does not match the network
+ * device address, assign an appropriate packet type.
+ */
+static inline void eth_skb_pkt_type(struct sk_buff *skb,
+				    const struct net_device *dev)
+{
+	const struct ethhdr *eth = eth_hdr(skb);
+
+	if (unlikely(!ether_addr_equal_64bits(eth->h_dest, dev->dev_addr))) {
+		if (unlikely(is_multicast_ether_addr_64bits(eth->h_dest))) {
+			if (ether_addr_equal_64bits(eth->h_dest, dev->broadcast))
+				skb->pkt_type = PACKET_BROADCAST;
+			else
+				skb->pkt_type = PACKET_MULTICAST;
+		} else {
+			skb->pkt_type = PACKET_OTHERHOST;
+		}
+	}
+}
+
+/**
  * eth_skb_pad - Pad buffer to mininum number of octets for Ethernet frame
  * @skb: Buffer to pad
  *
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ethtool.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ethtool.h
@@ -15,6 +15,7 @@
 
 #include <linux/bitmap.h>
 #include <linux/compat.h>
+#include <linux/if_ether.h>
 #include <linux/netlink.h>
 #include <uapi/linux/ethtool.h>
 
@@ -80,11 +81,6 @@
 struct net_device;
 struct netlink_ext_ack;
 
-/* Some generic methods drivers may use in their ethtool_ops */
-u32 ethtool_op_get_link(struct net_device *dev);
-int ethtool_op_get_ts_info(struct net_device *dev, struct ethtool_ts_info *eti);
-
-
 /* Link extended state and substate. */
 struct ethtool_link_ext_state_info {
 	enum ethtool_link_ext_state link_ext_state;
@@ -94,7 +90,7 @@
 		enum ethtool_link_ext_substate_link_logical_mismatch link_logical_mismatch;
 		enum ethtool_link_ext_substate_bad_signal_integrity bad_signal_integrity;
 		enum ethtool_link_ext_substate_cable_issue cable_issue;
-		u8 __link_ext_substate;
+		u32 __link_ext_substate;
 	};
 };
 
@@ -260,48 +256,59 @@
  * via a more targeted API.
  */
 struct ethtool_eth_mac_stats {
-	u64 FramesTransmittedOK;
-	u64 SingleCollisionFrames;
-	u64 MultipleCollisionFrames;
-	u64 FramesReceivedOK;
-	u64 FrameCheckSequenceErrors;
-	u64 AlignmentErrors;
-	u64 OctetsTransmittedOK;
-	u64 FramesWithDeferredXmissions;
-	u64 LateCollisions;
-	u64 FramesAbortedDueToXSColls;
-	u64 FramesLostDueToIntMACXmitError;
-	u64 CarrierSenseErrors;
-	u64 OctetsReceivedOK;
-	u64 FramesLostDueToIntMACRcvError;
-	u64 MulticastFramesXmittedOK;
-	u64 BroadcastFramesXmittedOK;
-	u64 FramesWithExcessiveDeferral;
-	u64 MulticastFramesReceivedOK;
-	u64 BroadcastFramesReceivedOK;
-	u64 InRangeLengthErrors;
-	u64 OutOfRangeLengthField;
-	u64 FrameTooLongErrors;
+	enum ethtool_mac_stats_src src;
+	struct_group(stats,
+		u64 FramesTransmittedOK;
+		u64 SingleCollisionFrames;
+		u64 MultipleCollisionFrames;
+		u64 FramesReceivedOK;
+		u64 FrameCheckSequenceErrors;
+		u64 AlignmentErrors;
+		u64 OctetsTransmittedOK;
+		u64 FramesWithDeferredXmissions;
+		u64 LateCollisions;
+		u64 FramesAbortedDueToXSColls;
+		u64 FramesLostDueToIntMACXmitError;
+		u64 CarrierSenseErrors;
+		u64 OctetsReceivedOK;
+		u64 FramesLostDueToIntMACRcvError;
+		u64 MulticastFramesXmittedOK;
+		u64 BroadcastFramesXmittedOK;
+		u64 FramesWithExcessiveDeferral;
+		u64 MulticastFramesReceivedOK;
+		u64 BroadcastFramesReceivedOK;
+		u64 InRangeLengthErrors;
+		u64 OutOfRangeLengthField;
+		u64 FrameTooLongErrors;
+	);
 };
 
 /* Basic IEEE 802.3 PHY statistics (30.3.2.1.*), not otherwise exposed
  * via a more targeted API.
  */
 struct ethtool_eth_phy_stats {
-	u64 SymbolErrorDuringCarrier;
+	enum ethtool_mac_stats_src src;
+	struct_group(stats,
+		u64 SymbolErrorDuringCarrier;
+	);
 };
 
 /* Basic IEEE 802.3 MAC Ctrl statistics (30.3.3.*), not otherwise exposed
  * via a more targeted API.
  */
 struct ethtool_eth_ctrl_stats {
-	u64 MACControlFramesTransmitted;
-	u64 MACControlFramesReceived;
-	u64 UnsupportedOpcodesReceived;
+	enum ethtool_mac_stats_src src;
+	struct_group(stats,
+		u64 MACControlFramesTransmitted;
+		u64 MACControlFramesReceived;
+		u64 UnsupportedOpcodesReceived;
+	);
 };
 
 /**
  * struct ethtool_pause_stats - statistics for IEEE 802.3x pause frames
+ * @src: input field denoting whether stats should be queried from the eMAC or
+ *	pMAC (if the MM layer is supported). To be ignored otherwise.
  * @tx_pause_frames: transmitted pause frame count. Reported to user space
  *	as %ETHTOOL_A_PAUSE_STAT_TX_FRAMES.
  *
@@ -315,8 +322,11 @@
  *	from the standard.
  */
 struct ethtool_pause_stats {
-	u64 tx_pause_frames;
-	u64 rx_pause_frames;
+	enum ethtool_mac_stats_src src;
+	struct_group(stats,
+		u64 tx_pause_frames;
+		u64 rx_pause_frames;
+	);
 };
 
 #define ETHTOOL_MAX_LANES	8
@@ -366,6 +376,8 @@
 
 /**
  * struct ethtool_rmon_stats - selected RMON (RFC 2819) statistics
+ * @src: input field denoting whether stats should be queried from the eMAC or
+ *	pMAC (if the MM layer is supported). To be ignored otherwise.
  * @undersize_pkts: Equivalent to `etherStatsUndersizePkts` from the RFC.
  * @oversize_pkts: Equivalent to `etherStatsOversizePkts` from the RFC.
  * @fragments: Equivalent to `etherStatsFragments` from the RFC.
@@ -381,13 +393,16 @@
  * ranges is left to the driver.
  */
 struct ethtool_rmon_stats {
-	u64 undersize_pkts;
-	u64 oversize_pkts;
-	u64 fragments;
-	u64 jabbers;
-
-	u64 hist[ETHTOOL_RMON_HIST_MAX];
-	u64 hist_tx[ETHTOOL_RMON_HIST_MAX];
+	enum ethtool_mac_stats_src src;
+	struct_group(stats,
+		u64 undersize_pkts;
+		u64 oversize_pkts;
+		u64 fragments;
+		u64 jabbers;
+
+		u64 hist[ETHTOOL_RMON_HIST_MAX];
+		u64 hist_tx[ETHTOOL_RMON_HIST_MAX];
+	);
 };
 
 #define ETH_MODULE_EEPROM_PAGE_LEN	128
@@ -416,6 +431,98 @@
 };
 
 /**
+ * struct ethtool_mm_state - 802.3 MAC merge layer state
+ * @verify_time:
+ *	wait time between verification attempts in ms (according to clause
+ *	30.14.1.6 aMACMergeVerifyTime)
+ * @max_verify_time:
+ *	maximum accepted value for the @verify_time variable in set requests
+ * @verify_status:
+ *	state of the verification state machine of the MM layer (according to
+ *	clause 30.14.1.2 aMACMergeStatusVerify)
+ * @tx_enabled:
+ *	set if the MM layer is administratively enabled in the TX direction
+ *	(according to clause 30.14.1.3 aMACMergeEnableTx)
+ * @tx_active:
+ *	set if the MM layer is enabled in the TX direction, which makes FP
+ *	possible (according to 30.14.1.5 aMACMergeStatusTx). This should be
+ *	true if MM is enabled, and the verification status is either verified,
+ *	or disabled.
+ * @pmac_enabled:
+ *	set if the preemptible MAC is powered on and is able to receive
+ *	preemptible packets and respond to verification frames.
+ * @verify_enabled:
+ *	set if the Verify function of the MM layer (which sends SMD-V
+ *	verification requests) is administratively enabled (regardless of
+ *	whether it is currently in the ETHTOOL_MM_VERIFY_STATUS_DISABLED state
+ *	or not), according to clause 30.14.1.4 aMACMergeVerifyDisableTx (but
+ *	using positive rather than negative logic). The device should always
+ *	respond to received SMD-V requests as long as @pmac_enabled is set.
+ * @tx_min_frag_size:
+ *	the minimum size of non-final mPacket fragments that the link partner
+ *	supports receiving, expressed in octets. Compared to the definition
+ *	from clause 30.14.1.7 aMACMergeAddFragSize which is expressed in the
+ *	range 0 to 3 (requiring a translation to the size in octets according
+ *	to the formula 64 * (1 + addFragSize) - 4), a value in a continuous and
+ *	unbounded range can be specified here.
+ * @rx_min_frag_size:
+ *	the minimum size of non-final mPacket fragments that this device
+ *	supports receiving, expressed in octets.
+ */
+struct ethtool_mm_state {
+	u32 verify_time;
+	u32 max_verify_time;
+	enum ethtool_mm_verify_status verify_status;
+	bool tx_enabled;
+	bool tx_active;
+	bool pmac_enabled;
+	bool verify_enabled;
+	u32 tx_min_frag_size;
+	u32 rx_min_frag_size;
+};
+
+/**
+ * struct ethtool_mm_cfg - 802.3 MAC merge layer configuration
+ * @verify_time: see struct ethtool_mm_state
+ * @verify_enabled: see struct ethtool_mm_state
+ * @tx_enabled: see struct ethtool_mm_state
+ * @pmac_enabled: see struct ethtool_mm_state
+ * @tx_min_frag_size: see struct ethtool_mm_state
+ */
+struct ethtool_mm_cfg {
+	u32 verify_time;
+	bool verify_enabled;
+	bool tx_enabled;
+	bool pmac_enabled;
+	u32 tx_min_frag_size;
+};
+
+/**
+ * struct ethtool_mm_stats - 802.3 MAC merge layer statistics
+ * @MACMergeFrameAssErrorCount:
+ *	received MAC frames with reassembly errors
+ * @MACMergeFrameSmdErrorCount:
+ *	received MAC frames/fragments rejected due to unknown or incorrect SMD
+ * @MACMergeFrameAssOkCount:
+ *	received MAC frames that were successfully reassembled and passed up
+ * @MACMergeFragCountRx:
+ *	number of additional correct SMD-C mPackets received due to preemption
+ * @MACMergeFragCountTx:
+ *	number of additional mPackets sent due to preemption
+ * @MACMergeHoldCount:
+ *	number of times the MM layer entered the HOLD state, which blocks
+ *	transmission of preemptible traffic
+ */
+struct ethtool_mm_stats {
+	u64 MACMergeFrameAssErrorCount;
+	u64 MACMergeFrameSmdErrorCount;
+	u64 MACMergeFrameAssOkCount;
+	u64 MACMergeFragCountRx;
+	u64 MACMergeFragCountTx;
+	u64 MACMergeHoldCount;
+};
+
+/**
  * struct ethtool_ops - optional netdev operations
  * @cap_link_lanes_supported: indicates if the driver supports lanes
  *	parameter.
@@ -580,6 +687,9 @@
  * @get_eth_ctrl_stats: Query some of the IEEE 802.3 MAC Ctrl statistics.
  * @get_rmon_stats: Query some of the RMON (RFC 2819) statistics.
  *	Set %ranges to a pointer to zero-terminated array of byte ranges.
+ * @get_mm: Query the 802.3 MAC Merge layer state.
+ * @set_mm: Set the 802.3 MAC Merge layer parameters.
+ * @get_mm_stats: Query the 802.3 MAC Merge layer statistics.
  *
  * All operations are optional (i.e. the function pointer may be set
  * to %NULL) and callers must take this into account.  Callers must
@@ -705,6 +815,10 @@
 	void	(*get_rmon_stats)(struct net_device *dev,
 				  struct ethtool_rmon_stats *rmon_stats,
 				  const struct ethtool_rmon_hist_range **ranges);
+	int	(*get_mm)(struct net_device *dev, struct ethtool_mm_state *state);
+	int	(*set_mm)(struct net_device *dev, struct ethtool_mm_cfg *cfg,
+			  struct netlink_ext_ack *extack);
+	void	(*get_mm_stats)(struct net_device *dev, struct ethtool_mm_stats *stats);
 };
 
 int ethtool_check_ops(const struct ethtool_ops *ops);
@@ -779,12 +893,57 @@
  */
 int ethtool_get_phc_vclocks(struct net_device *dev, int **vclock_index);
 
+/* Some generic methods drivers may use in their ethtool_ops */
+u32 ethtool_op_get_link(struct net_device *dev);
+int ethtool_op_get_ts_info(struct net_device *dev, struct ethtool_ts_info *eti);
+
+/**
+ * ethtool_mm_frag_size_add_to_min - Translate (standard) additional fragment
+ *	size expressed as multiplier into (absolute) minimum fragment size
+ *	value expressed in octets
+ * @val_add: Value of addFragSize multiplier
+ */
+static inline u32 ethtool_mm_frag_size_add_to_min(u32 val_add)
+{
+	return (ETH_ZLEN + ETH_FCS_LEN) * (1 + val_add) - ETH_FCS_LEN;
+}
+
+/**
+ * ethtool_mm_frag_size_min_to_add - Translate (absolute) minimum fragment size
+ *	expressed in octets into (standard) additional fragment size expressed
+ *	as multiplier
+ * @val_min: Value of addFragSize variable in octets
+ * @val_add: Pointer where the standard addFragSize value is to be returned
+ * @extack: Netlink extended ack
+ *
+ * Translate a value in octets to one of 0, 1, 2, 3 according to the reverse
+ * application of the 802.3 formula 64 * (1 + addFragSize) - 4. To be called
+ * by drivers which do not support programming the minimum fragment size to a
+ * continuous range. Returns error on other fragment length values.
+ */
+static inline int ethtool_mm_frag_size_min_to_add(u32 val_min, u32 *val_add,
+						  struct netlink_ext_ack *extack)
+{
+	u32 add_frag_size;
+
+	for (add_frag_size = 0; add_frag_size < 4; add_frag_size++) {
+		if (ethtool_mm_frag_size_add_to_min(add_frag_size) == val_min) {
+			*val_add = add_frag_size;
+			return 0;
+		}
+	}
+
+	NL_SET_ERR_MSG_MOD(extack,
+			   "minFragSize required to be one of 60, 124, 188 or 252");
+	return -EINVAL;
+}
+
 /**
  * ethtool_sprintf - Write formatted string to ethtool string data
- * @data: Pointer to start of string to update
+ * @data: Pointer to a pointer to the start of string to update
  * @fmt: Format of string to write
  *
- * Write formatted string to data. Update data to point at start of
+ * Write formatted string to *data. Update *data to point at start of
  * next string.
  */
 extern __printf(2, 3) void ethtool_sprintf(u8 **data, const char *fmt, ...);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ethtool_netlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ethtool_netlink.h
@@ -10,6 +10,9 @@
 #define __ETHTOOL_LINK_MODE_MASK_NWORDS \
 	DIV_ROUND_UP(__ETHTOOL_LINK_MODE_MASK_NBITS, 32)
 
+#define ETHTOOL_PAUSE_STAT_CNT	(__ETHTOOL_A_PAUSE_STAT_CNT -		\
+				 ETHTOOL_A_PAUSE_STAT_TX_FRAMES)
+
 enum ethtool_multicast_groups {
 	ETHNL_MCGRP_MONITOR,
 };
@@ -26,6 +29,17 @@
 int ethnl_cable_test_pulse(struct phy_device *phydev, u16 mV);
 int ethnl_cable_test_step(struct phy_device *phydev, u32 first, u32 last,
 			  u32 step);
+void ethtool_aggregate_mac_stats(struct net_device *dev,
+				 struct ethtool_eth_mac_stats *mac_stats);
+void ethtool_aggregate_phy_stats(struct net_device *dev,
+				 struct ethtool_eth_phy_stats *phy_stats);
+void ethtool_aggregate_ctrl_stats(struct net_device *dev,
+				  struct ethtool_eth_ctrl_stats *ctrl_stats);
+void ethtool_aggregate_pause_stats(struct net_device *dev,
+				   struct ethtool_pause_stats *pause_stats);
+void ethtool_aggregate_rmon_stats(struct net_device *dev,
+				  struct ethtool_rmon_stats *rmon_stats);
+
 #else
 static inline int ethnl_cable_test_alloc(struct phy_device *phydev, u8 cmd)
 {
@@ -67,5 +81,36 @@
 {
 	return -EOPNOTSUPP;
 }
+
+static inline void
+ethtool_aggregate_mac_stats(struct net_device *dev,
+			    struct ethtool_eth_mac_stats *mac_stats)
+{
+}
+
+static inline void
+ethtool_aggregate_phy_stats(struct net_device *dev,
+			    struct ethtool_eth_phy_stats *phy_stats)
+{
+}
+
+static inline void
+ethtool_aggregate_ctrl_stats(struct net_device *dev,
+			     struct ethtool_eth_ctrl_stats *ctrl_stats)
+{
+}
+
+static inline void
+ethtool_aggregate_pause_stats(struct net_device *dev,
+			      struct ethtool_pause_stats *pause_stats)
+{
+}
+
+static inline void
+ethtool_aggregate_rmon_stats(struct net_device *dev,
+			     struct ethtool_rmon_stats *rmon_stats)
+{
+}
+
 #endif /* IS_ENABLED(CONFIG_ETHTOOL_NETLINK) */
 #endif /* _LINUX_ETHTOOL_NETLINK_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/eventfd.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/eventfd.h
@@ -40,13 +40,14 @@
 struct eventfd_ctx *eventfd_ctx_fdget(int fd);
 struct eventfd_ctx *eventfd_ctx_fileget(struct file *file);
 __u64 eventfd_signal(struct eventfd_ctx *ctx, __u64 n);
+__u64 eventfd_signal_mask(struct eventfd_ctx *ctx, __u64 n, unsigned mask);
 int eventfd_ctx_remove_wait_queue(struct eventfd_ctx *ctx, wait_queue_entry_t *wait,
 				  __u64 *cnt);
 void eventfd_ctx_do_read(struct eventfd_ctx *ctx, __u64 *cnt);
 
 static inline bool eventfd_signal_allowed(void)
 {
-	return !current->in_eventfd_signal;
+	return !current->in_eventfd;
 }
 
 #else /* CONFIG_EVENTFD */
@@ -61,7 +62,13 @@
 	return ERR_PTR(-ENOSYS);
 }
 
-static inline int eventfd_signal(struct eventfd_ctx *ctx, int n)
+static inline int eventfd_signal(struct eventfd_ctx *ctx, __u64 n)
+{
+	return -ENOSYS;
+}
+
+static inline int eventfd_signal_mask(struct eventfd_ctx *ctx, __u64 n,
+				      unsigned mask)
 {
 	return -ENOSYS;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/eventpoll.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/eventpoll.h
@@ -42,7 +42,7 @@
 	 * because the file in on the way to be removed and nobody ( but
 	 * eventpoll ) has still a reference to this file.
 	 */
-	if (likely(!file->f_ep))
+	if (likely(!READ_ONCE(file->f_ep)))
 		return;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/export.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/export.h
@@ -2,6 +2,8 @@
 #ifndef _LINUX_EXPORT_H
 #define _LINUX_EXPORT_H
 
+#include <linux/stringify.h>
+
 /*
  * Export symbols from the kernel to modules.  Forked from module.h
  * to reduce the amount of pointless cruft we feed to gcc when only
@@ -154,7 +156,6 @@
 #endif /* CONFIG_MODULES */
 
 #ifdef DEFAULT_SYMBOL_NAMESPACE
-#include <linux/stringify.h>
 #define _EXPORT_SYMBOL(sym, sec)	__EXPORT_SYMBOL(sym, sec, __stringify(DEFAULT_SYMBOL_NAMESPACE))
 #else
 #define _EXPORT_SYMBOL(sym, sec)	__EXPORT_SYMBOL(sym, sec, "")
@@ -162,8 +163,8 @@
 
 #define EXPORT_SYMBOL(sym)		_EXPORT_SYMBOL(sym, "")
 #define EXPORT_SYMBOL_GPL(sym)		_EXPORT_SYMBOL(sym, "_gpl")
-#define EXPORT_SYMBOL_NS(sym, ns)	__EXPORT_SYMBOL(sym, "", #ns)
-#define EXPORT_SYMBOL_NS_GPL(sym, ns)	__EXPORT_SYMBOL(sym, "_gpl", #ns)
+#define EXPORT_SYMBOL_NS(sym, ns)	__EXPORT_SYMBOL(sym, "", __stringify(ns))
+#define EXPORT_SYMBOL_NS_GPL(sym, ns)	__EXPORT_SYMBOL(sym, "_gpl", __stringify(ns))
 
 #endif /* !__ASSEMBLY__ */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/exportfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/exportfs.h
@@ -221,8 +221,7 @@
 #define EXPORT_OP_NOATOMIC_ATTR		(0x10) /* Filesystem cannot supply
 						  atomic attribute updates
 						*/
-#define EXPORT_OP_SYNC_LOCKS		(0x20) /* Filesystem can't do
-						  asychronous blocking locks */
+#define EXPORT_OP_FLUSH_ON_CLOSE	(0x20) /* fs flushes file data on close */
 	unsigned long	flags;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/extcon.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/extcon.h
@@ -296,7 +296,7 @@
 
 static inline struct extcon_dev *extcon_get_extcon_dev(const char *extcon_name)
 {
-	return ERR_PTR(-ENODEV);
+	return NULL;
 }
 
 static inline struct extcon_dev *extcon_find_edev_by_node(struct device_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/f2fs_fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/f2fs_fs.h
@@ -227,7 +227,7 @@
 #define F2FS_INLINE_DATA	0x02	/* file inline data flag */
 #define F2FS_INLINE_DENTRY	0x04	/* file inline dentry flag */
 #define F2FS_DATA_EXIST		0x08	/* file inline data exist flag */
-#define F2FS_INLINE_DOTS	0x10	/* file having implicit dot dentries */
+#define F2FS_INLINE_DOTS	0x10	/* file having implicit dot dentries (obsolete) */
 #define F2FS_EXTRA_ATTR		0x20	/* file having extra attribute */
 #define F2FS_PIN_FILE		0x40	/* file should not be gced */
 #define F2FS_COMPRESS_RELEASED	0x80	/* file released compressed blocks */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fanotify.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fanotify.h
@@ -25,7 +25,7 @@
 
 #define FANOTIFY_CLASS_BITS	(FAN_CLASS_NOTIF | FANOTIFY_PERM_CLASSES)
 
-#define FANOTIFY_FID_BITS	(FAN_REPORT_FID | FAN_REPORT_DFID_NAME)
+#define FANOTIFY_FID_BITS	(FAN_REPORT_DFID_NAME_TARGET)
 
 #define FANOTIFY_INFO_MODES	(FANOTIFY_FID_BITS | FAN_REPORT_PIDFD)
 
@@ -61,14 +61,19 @@
 #define FANOTIFY_MARK_TYPE_BITS	(FAN_MARK_INODE | FAN_MARK_MOUNT | \
 				 FAN_MARK_FILESYSTEM)
 
+#define FANOTIFY_MARK_CMD_BITS	(FAN_MARK_ADD | FAN_MARK_REMOVE | \
+				 FAN_MARK_FLUSH)
+
+#define FANOTIFY_MARK_IGNORE_BITS (FAN_MARK_IGNORED_MASK | \
+				   FAN_MARK_IGNORE)
+
 #define FANOTIFY_MARK_FLAGS	(FANOTIFY_MARK_TYPE_BITS | \
-				 FAN_MARK_ADD | \
-				 FAN_MARK_REMOVE | \
+				 FANOTIFY_MARK_CMD_BITS | \
+				 FANOTIFY_MARK_IGNORE_BITS | \
 				 FAN_MARK_DONT_FOLLOW | \
 				 FAN_MARK_ONLYDIR | \
-				 FAN_MARK_IGNORED_MASK | \
 				 FAN_MARK_IGNORED_SURV_MODIFY | \
-				 FAN_MARK_FLUSH)
+				 FAN_MARK_EVICTABLE)
 
 /*
  * Events that can be reported with data type FSNOTIFY_EVENT_PATH.
@@ -82,15 +87,23 @@
  * Directory entry modification events - reported only to directory
  * where entry is modified and not to a watching parent.
  */
-#define FANOTIFY_DIRENT_EVENTS	(FAN_MOVE | FAN_CREATE | FAN_DELETE)
+#define FANOTIFY_DIRENT_EVENTS	(FAN_MOVE | FAN_CREATE | FAN_DELETE | \
+				 FAN_RENAME)
+
+/* Events that can be reported with event->fd */
+#define FANOTIFY_FD_EVENTS (FANOTIFY_PATH_EVENTS | FANOTIFY_PERM_EVENTS)
 
 /* Events that can only be reported with data type FSNOTIFY_EVENT_INODE */
 #define FANOTIFY_INODE_EVENTS	(FANOTIFY_DIRENT_EVENTS | \
 				 FAN_ATTRIB | FAN_MOVE_SELF | FAN_DELETE_SELF)
 
+/* Events that can only be reported with data type FSNOTIFY_EVENT_ERROR */
+#define FANOTIFY_ERROR_EVENTS	(FAN_FS_ERROR)
+
 /* Events that user can request to be notified on */
 #define FANOTIFY_EVENTS		(FANOTIFY_PATH_EVENTS | \
-				 FANOTIFY_INODE_EVENTS)
+				 FANOTIFY_INODE_EVENTS | \
+				 FANOTIFY_ERROR_EVENTS)
 
 /* Events that require a permission response from user */
 #define FANOTIFY_PERM_EVENTS	(FAN_OPEN_PERM | FAN_ACCESS_PERM | \
@@ -104,6 +117,10 @@
 					 FANOTIFY_PERM_EVENTS | \
 					 FAN_Q_OVERFLOW | FAN_ONDIR)
 
+/* Events and flags relevant only for directories */
+#define FANOTIFY_DIRONLY_EVENT_BITS	(FANOTIFY_DIRENT_EVENTS | \
+					 FAN_EVENT_ON_CHILD | FAN_ONDIR)
+
 #define ALL_FANOTIFY_EVENT_BITS		(FANOTIFY_OUTGOING_EVENTS | \
 					 FANOTIFY_EVENT_FLAGS)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fb.h
@@ -201,11 +201,20 @@
 };
 
 #ifdef CONFIG_FB_DEFERRED_IO
+struct fb_deferred_io_pageref {
+	struct page *page;
+	unsigned long offset;
+	/* private */
+	struct list_head list;
+};
+
 struct fb_deferred_io {
 	/* delay between mkwrite and deferred handler */
 	unsigned long delay;
-	struct mutex lock; /* mutex that protects the page list */
-	struct list_head pagelist; /* list of touched pages */
+	bool sort_pagereflist; /* sort pagelist by offset */
+	int open_count; /* number of opened files; protected by fb_info lock */
+	struct mutex lock; /* mutex that protects the pageref list */
+	struct list_head pagereflist; /* list of pagerefs for touched pages */
 	/* callback */
 	void (*first_io)(struct fb_info *info);
 	void (*deferred_io)(struct fb_info *info, struct list_head *pagelist);
@@ -468,6 +477,8 @@
 #endif
 #ifdef CONFIG_FB_DEFERRED_IO
 	struct delayed_work deferred_work;
+	unsigned long npagerefs;
+	struct fb_deferred_io_pageref *pagerefs;
 	struct fb_deferred_io *fbdefio;
 #endif
 
@@ -502,6 +513,7 @@
 	} *apertures;
 
 	bool skip_vt_switch; /* no VT switch on suspend/resume required */
+	bool forced_out; /* set when being removed by another driver */
 };
 
 static inline struct apertures_struct *alloc_apertures(unsigned int max_num) {
@@ -610,6 +622,7 @@
 					       const char *name);
 extern int remove_conflicting_framebuffers(struct apertures_struct *a,
 					   const char *name, bool primary);
+extern bool is_firmware_framebuffer(struct apertures_struct *a);
 extern int fb_prepare_logo(struct fb_info *fb_info, int rotate);
 extern int fb_show_logo(struct fb_info *fb_info, int rotate);
 extern char* fb_get_buffer_offset(struct fb_info *info, struct fb_pixmap *buf, u32 size);
@@ -659,10 +672,11 @@
 
 /* drivers/video/fb_defio.c */
 int fb_deferred_io_mmap(struct fb_info *info, struct vm_area_struct *vma);
-extern void fb_deferred_io_init(struct fb_info *info);
+extern int  fb_deferred_io_init(struct fb_info *info);
 extern void fb_deferred_io_open(struct fb_info *info,
 				struct inode *inode,
 				struct file *file);
+extern void fb_deferred_io_release(struct fb_info *info);
 extern void fb_deferred_io_cleanup(struct fb_info *info);
 extern int fb_deferred_io_fsync(struct file *file, loff_t start,
 				loff_t end, int datasync);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fbcon.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fbcon.h
@@ -15,6 +15,8 @@
 void fbcon_get_requirement(struct fb_info *info,
 			   struct fb_blit_caps *caps);
 void fbcon_fb_blanked(struct fb_info *info, int blank);
+int  fbcon_modechange_possible(struct fb_info *info,
+			       struct fb_var_screeninfo *var);
 void fbcon_update_vcs(struct fb_info *info, bool all);
 void fbcon_remap_all(struct fb_info *info);
 int fbcon_set_con2fb_map_ioctl(void __user *argp);
@@ -33,6 +35,8 @@
 static inline void fbcon_get_requirement(struct fb_info *info,
 					 struct fb_blit_caps *caps) {}
 static inline void fbcon_fb_blanked(struct fb_info *info, int blank) {}
+static inline int  fbcon_modechange_possible(struct fb_info *info,
+				struct fb_var_screeninfo *var) { return 0; }
 static inline void fbcon_update_vcs(struct fb_info *info, bool all) {}
 static inline void fbcon_remap_all(struct fb_info *info) {}
 static inline int fbcon_set_con2fb_map_ioctl(void __user *argp) { return 0; }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fdtable.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fdtable.h
@@ -22,7 +22,6 @@
  * as this is the granularity returned by copy_fdset().
  */
 #define NR_OPEN_DEFAULT BITS_PER_LONG
-#define NR_OPEN_MAX ~0U
 
 struct fdtable {
 	unsigned int max_fds;
@@ -117,7 +116,10 @@
 
 void put_files_struct(struct files_struct *fs);
 int unshare_files(void);
-struct files_struct *dup_fd(struct files_struct *, unsigned, int *) __latent_entropy;
+struct fd_range {
+	unsigned int from, to;
+};
+struct files_struct *dup_fd(struct files_struct *, struct fd_range *) __latent_entropy;
 void do_close_on_exec(struct files_struct *);
 int iterate_fd(struct files_struct *, unsigned,
 		int (*)(const void *, struct file *, unsigned),
@@ -126,8 +128,6 @@
 extern int close_fd(unsigned int fd);
 extern int __close_range(unsigned int fd, unsigned int max_fd, unsigned int flags);
 extern int close_fd_get_file(unsigned int fd, struct file **res);
-extern int unshare_fd(unsigned long unshare_flags, unsigned int max_fds,
-		      struct files_struct **new_fdp);
 
 extern struct kmem_cache *files_cachep;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/filter.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/filter.h
@@ -496,24 +496,27 @@
 	__BPF_MAP(n, __BPF_DECL_ARGS, __BPF_N, u64, __ur_1, u64, __ur_2,       \
 		  u64, __ur_3, u64, __ur_4, u64, __ur_5)
 
-#define BPF_CALL_x(x, name, ...)					       \
+#define BPF_CALL_x(x, attr, name, ...)					       \
 	static __always_inline						       \
 	u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__));   \
 	typedef u64 (*btf_##name)(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
-	u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__));	       \
-	u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__))	       \
+	attr u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__));    \
+	attr u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__))     \
 	{								       \
 		return ((btf_##name)____##name)(__BPF_MAP(x,__BPF_CAST,__BPF_N,__VA_ARGS__));\
 	}								       \
 	static __always_inline						       \
 	u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__))
 
-#define BPF_CALL_0(name, ...)	BPF_CALL_x(0, name, __VA_ARGS__)
-#define BPF_CALL_1(name, ...)	BPF_CALL_x(1, name, __VA_ARGS__)
-#define BPF_CALL_2(name, ...)	BPF_CALL_x(2, name, __VA_ARGS__)
-#define BPF_CALL_3(name, ...)	BPF_CALL_x(3, name, __VA_ARGS__)
-#define BPF_CALL_4(name, ...)	BPF_CALL_x(4, name, __VA_ARGS__)
-#define BPF_CALL_5(name, ...)	BPF_CALL_x(5, name, __VA_ARGS__)
+#define __NOATTR
+#define BPF_CALL_0(name, ...)	BPF_CALL_x(0, __NOATTR, name, __VA_ARGS__)
+#define BPF_CALL_1(name, ...)	BPF_CALL_x(1, __NOATTR, name, __VA_ARGS__)
+#define BPF_CALL_2(name, ...)	BPF_CALL_x(2, __NOATTR, name, __VA_ARGS__)
+#define BPF_CALL_3(name, ...)	BPF_CALL_x(3, __NOATTR, name, __VA_ARGS__)
+#define BPF_CALL_4(name, ...)	BPF_CALL_x(4, __NOATTR, name, __VA_ARGS__)
+#define BPF_CALL_5(name, ...)	BPF_CALL_x(5, __NOATTR, name, __VA_ARGS__)
+
+#define NOTRACE_BPF_CALL_1(name, ...)	BPF_CALL_x(1, notrace, name, __VA_ARGS__)
 
 #define bpf_ctx_range(TYPE, MEMBER)						\
 	offsetof(TYPE, MEMBER) ... offsetofend(TYPE, MEMBER) - 1
@@ -554,9 +557,9 @@
 };
 
 struct bpf_prog_stats {
-	u64 cnt;
-	u64 nsecs;
-	u64 misses;
+	u64_stats_t cnt;
+	u64_stats_t nsecs;
+	u64_stats_t misses;
 	struct u64_stats_sync syncp;
 } __aligned(2 * sizeof(u64));
 
@@ -613,13 +616,14 @@
 	if (static_branch_unlikely(&bpf_stats_enabled_key)) {
 		struct bpf_prog_stats *stats;
 		u64 start = sched_clock();
+		unsigned long flags;
 
 		ret = dfunc(ctx, prog->insnsi, prog->bpf_func);
 		stats = this_cpu_ptr(prog->stats);
-		u64_stats_update_begin(&stats->syncp);
-		stats->cnt++;
-		stats->nsecs += sched_clock() - start;
-		u64_stats_update_end(&stats->syncp);
+		flags = u64_stats_update_begin_irqsave(&stats->syncp);
+		u64_stats_inc(&stats->cnt);
+		u64_stats_add(&stats->nsecs, sched_clock() - start);
+		u64_stats_update_end_irqrestore(&stats->syncp, flags);
 	} else {
 		ret = dfunc(ctx, prog->insnsi, prog->bpf_func);
 	}
@@ -638,9 +642,6 @@
  * This uses migrate_disable/enable() explicitly to document that the
  * invocation of a BPF program does not require reentrancy protection
  * against a BPF program which is invoked from a preempting task.
- *
- * For non RT enabled kernels migrate_disable/enable() maps to
- * preempt_disable/enable(), i.e. it disables also preemption.
  */
 static inline u32 bpf_prog_run_pin_on_cpu(const struct bpf_prog *prog,
 					  const void *ctx)
@@ -874,14 +875,15 @@
 
 #define bpf_classic_proglen(fprog) (fprog->len * sizeof(fprog->filter[0]))
 
-static inline void bpf_prog_lock_ro(struct bpf_prog *fp)
+static inline int __must_check bpf_prog_lock_ro(struct bpf_prog *fp)
 {
 #ifndef CONFIG_BPF_JIT_ALWAYS_ON
 	if (!fp->jited) {
 		set_vm_flush_reset_perms(fp);
-		set_memory_ro((unsigned long)fp, fp->pages);
+		return set_memory_ro((unsigned long)fp, fp->pages);
 	}
 #endif
+	return 0;
 }
 
 static inline void bpf_jit_binary_lock_ro(struct bpf_binary_header *hdr)
@@ -942,8 +944,7 @@
 int sk_reuseport_attach_bpf(u32 ufd, struct sock *sk);
 void sk_reuseport_prog_free(struct bpf_prog *prog);
 int sk_detach_filter(struct sock *sk);
-int sk_get_filter(struct sock *sk, struct sock_filter __user *filter,
-		  unsigned int len);
+int sk_get_filter(struct sock *sk, sockptr_t optval, unsigned int len);
 
 bool sk_filter_charge(struct sock *sk, struct sk_filter *fp);
 void sk_filter_uncharge(struct sock *sk, struct sk_filter *fp);
@@ -1020,6 +1021,10 @@
 int xdp_do_redirect(struct net_device *dev,
 		    struct xdp_buff *xdp,
 		    struct bpf_prog *prog);
+int xdp_do_redirect_frame(struct net_device *dev,
+			  struct xdp_buff *xdp,
+			  struct xdp_frame *xdpf,
+			  struct bpf_prog *prog);
 void xdp_do_flush(void);
 
 /* The xdp_do_flush_map() helper has been renamed to drop the _map suffix, as
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/firmware/xlnx-error-events.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/firmware/xlnx-error-events.h
@@ -0,0 +1,640 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx Versal Error Event Node IDs and Error Event Mask.
+ * Use with Xilinx Event Management Driver
+ *
+ * Copyright (C) 2021 Xilinx
+ *
+ * Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
+ */
+
+#ifndef _FIRMWARE_XLNX_ERROR_EVENTS_H_
+#define _FIRMWARE_XLNX_ERROR_EVENTS_H_
+
+/*
+ * Error Event Node Ids
+ */
+#define XPM_NODETYPE_EVENT_ERROR_PMC_ERR1	(0x28100000U)
+#define XPM_NODETYPE_EVENT_ERROR_PMC_ERR2	(0x28104000U)
+#define XPM_NODETYPE_EVENT_ERROR_PSM_ERR1	(0x28108000U)
+#define XPM_NODETYPE_EVENT_ERROR_PSM_ERR2	(0x2810C000U)
+#define XPM_NODETYPE_EVENT_ERROR_SW_ERR		(0x28110000U)
+
+/*
+ * Error Event Mask belongs to PMC ERR2 node.
+ * For which Node_Id = XPM_NODETYPE_EVENT_ERROR_PMC_ERR2
+ */
+
+/**
+ * XPM_EVENT_ERROR_MASK_BOOT_CR: Error event mask for PMC Boot Correctable Error.
+ * Set by ROM code during ROM execution during Boot.
+ */
+#define XPM_EVENT_ERROR_MASK_BOOT_CR		BIT(0)
+
+/**
+ * XPM_EVENT_ERROR_MASK_BOOT_NCR: Error event mask for PMC Boot Non-Correctable Error.
+ * Set by ROM code during ROM execution during Boot.
+ */
+#define XPM_EVENT_ERROR_MASK_BOOT_NCR		BIT(1)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FW_CR: Error event mask for PMC Firmware Boot Correctable Error.
+ * Set by PLM during firmware execution during Boot.
+ */
+#define XPM_EVENT_ERROR_MASK_FW_CR		BIT(2)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FW_NCR: Error event mask for PMC Firmware Boot Non-Correctable Error.
+ * Set by PLM during firmware execution during Boot.
+ */
+#define XPM_EVENT_ERROR_MASK_FW_NCR		BIT(3)
+
+/**
+ * XPM_EVENT_ERROR_MASK_GSW_CR: Error event mask for General Software Correctable Error.
+ * Set by any processors after Boot.
+ */
+#define XPM_EVENT_ERROR_MASK_GSW_CR		BIT(4)
+
+/**
+ * XPM_EVENT_ERROR_MASK_GSW_NCR: Error event mask for General Software Non-Correctable Error.
+ * Set by any processors after Boot.
+ */
+#define XPM_EVENT_ERROR_MASK_GSW_NCR		BIT(5)
+
+/**
+ * XPM_EVENT_ERROR_MASK_CFU: Error event mask for CFU Error.
+ */
+#define XPM_EVENT_ERROR_MASK_CFU		BIT(6)
+
+/**
+ * XPM_EVENT_ERROR_MASK_CFRAME: Error event mask for CFRAME Error.
+ */
+#define XPM_EVENT_ERROR_MASK_CFRAME		BIT(7)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMC_PSM_CR: Error event mask for PSM Correctable Error,
+ * Summary from PSM Error Management.
+ */
+#define XPM_EVENT_ERROR_MASK_PMC_PSM_CR		BIT(8)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMC_PSM_NCR: Error event mask for PSM Non-Correctable Error,
+ * Summary from PSM Error Management.
+ */
+#define XPM_EVENT_ERROR_MASK_PMC_PSM_NCR	BIT(9)
+
+/**
+ * XPM_EVENT_ERROR_MASK_DDRMB_CR: Error event mask for DDRMC MB Correctable ECC Error.
+ */
+#define XPM_EVENT_ERROR_MASK_DDRMB_CR		BIT(10)
+
+/**
+ * XPM_EVENT_ERROR_MASK_DDRMB_NCR: Error event mask for DDRMC MB Non-Correctable ECC Error.
+ */
+#define XPM_EVENT_ERROR_MASK_DDRMB_NCR		BIT(11)
+
+/**
+ * XPM_EVENT_ERROR_MASK_NOCTYPE1_CR: Error event mask for NoC Type1 Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_NOCTYPE1_CR	BIT(12)
+
+/**
+ * XPM_EVENT_ERROR_MASK_NOCTYPE1_NCR: Error event mask for NoC Type1 Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_NOCTYPE1_NCR	BIT(13)
+
+/**
+ * XPM_EVENT_ERROR_MASK_NOCUSER: Error event mask for NoC User Error.
+ */
+#define XPM_EVENT_ERROR_MASK_NOCUSER		BIT(14)
+
+/**
+ * XPM_EVENT_ERROR_MASK_MMCM: Error event mask for MMCM Lock Error.
+ */
+#define XPM_EVENT_ERROR_MASK_MMCM		BIT(15)
+
+/**
+ * XPM_EVENT_ERROR_MASK_AIE_CR: Error event mask for ME Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_AIE_CR		BIT(16)
+
+/**
+ * XPM_EVENT_ERROR_MASK_AIE_NCR: Error event mask for ME Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_AIE_NCR		BIT(17)
+
+/**
+ * XPM_EVENT_ERROR_MASK_DDRMC_CR: Error event mask for DDRMC MC Correctable ECC Error.
+ */
+#define XPM_EVENT_ERROR_MASK_DDRMC_CR		BIT(18)
+
+/**
+ * XPM_EVENT_ERROR_MASK_DDRMC_NCR: Error event mask for DDRMC MC Non-Correctable ECC Error.
+ */
+#define XPM_EVENT_ERROR_MASK_DDRMC_NCR		BIT(19)
+
+/**
+ * XPM_EVENT_ERROR_MASK_GT_CR: Error event mask for GT Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_GT_CR		BIT(20)
+
+/**
+ * XPM_EVENT_ERROR_MASK_GT_NCR: Error event mask for GT Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_GT_NCR		BIT(21)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PLSMON_CR: Error event mask for PL Sysmon Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PLSMON_CR		BIT(22)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PLSMON_NCR: Error event mask for PL Sysmon Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PLSMON_NCR		BIT(23)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PL0: Error event mask for User defined PL generic error.
+ */
+#define XPM_EVENT_ERROR_MASK_PL0		BIT(24)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PL1: Error event mask for User defined PL generic error.
+ */
+#define XPM_EVENT_ERROR_MASK_PL1		BIT(25)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PL2: Error event mask for User defined PL generic error.
+ */
+#define XPM_EVENT_ERROR_MASK_PL2		BIT(26)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PL3: Error event mask for User defined PL generic error.
+ */
+#define XPM_EVENT_ERROR_MASK_PL3		BIT(27)
+
+/**
+ * XPM_EVENT_ERROR_MASK_NPIROOT: Error event mask for NPI Root Error.
+ */
+#define XPM_EVENT_ERROR_MASK_NPIROOT		BIT(28)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SSIT3: Error event mask for SSIT Error from Slave SLR1,
+ * Only used in Master SLR.
+ */
+#define XPM_EVENT_ERROR_MASK_SSIT3		BIT(29)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SSIT4: Error event mask for SSIT Error from Slave SLR2,
+ * Only used in Master SLR.
+ */
+#define XPM_EVENT_ERROR_MASK_SSIT4		BIT(30)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SSIT5: Error event mask for SSIT Error from Slave SLR3,
+ * Only used in Master SLR.
+ */
+#define XPM_EVENT_ERROR_MASK_SSIT5		BIT(31)
+
+/*
+ * Error Event Mask belongs to PMC ERR2 node,
+ * For which Node_Id = XPM_NODETYPE_EVENT_ERROR_PMC_ERR2
+ */
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCAPB: Error event mask for General purpose PMC error,
+ * can be triggered by any of the following peripherals:,
+ * - PMC Global Regsiters,- PMC Clock & Reset (CRP),- PMC IOU Secure SLCR,
+ * - PMC IOU SLCR,- BBRAM Controller,- PMC Analog Control Registers,
+ * - RTC Control Registers.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCAPB		BIT(0)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCROM: Error event mask for PMC ROM Validation Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCROM		BIT(1)
+
+/**
+ * XPM_EVENT_ERROR_MASK_MB_FATAL0: Error event mask for PMC PPU0 MB TMR Fatal Error.
+ */
+#define XPM_EVENT_ERROR_MASK_MB_FATAL0		BIT(2)
+
+/**
+ * XPM_EVENT_ERROR_MASK_MB_FATAL1: Error event mask for PMC PPU1 MB TMR Fatal Error.
+ */
+#define XPM_EVENT_ERROR_MASK_MB_FATAL1		BIT(3)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCPAR: Error event mask for PMC Switch and PMC IOU Parity Errors.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCPAR		BIT(4)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMC_CR: Error event mask for PMC Correctable Errors,
+ * PPU0 RAM correctable error.,PPU1 instruction RAM correctable error.,
+ * PPU1 data RAM correctable error.
+ */
+#define XPM_EVENT_ERROR_MASK_PMC_CR		BIT(5)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMC_NCR: Error event mask for PMC Non-Correctable Errors,
+ * PPU0 RAM non-correctable error.,PPU1 instruction RAM non-correctable error.,
+ * PPU1 data RAM non-correctable error.,PRAM non-correctable error.
+ */
+#define XPM_EVENT_ERROR_MASK_PMC_NCR		BIT(6)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON0: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[0].
+ * Indicates an alarm condition on any of SUPPLY0 to SUPPLY31.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON0		BIT(7)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON1: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[1].
+ * Indicates an alarm condition on any of SUPPLY32 to SUPPLY63.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON1		BIT(8)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON2: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[2].
+ * Indicates an alarm condition on any of SUPPLY64 to SUPPLY95.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON2		BIT(9)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON3: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[3].
+ * Indicates an alarm condition on any of SUPPLY96 to SUPPLY127.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON3		BIT(10)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON4: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[4].
+ * Indicates an alarm condition on any of SUPPLY128 to SUPPLY159.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON4		BIT(11)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON8: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[8].
+ * Indicates an over-temperature alarm.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON8		BIT(15)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCSMON9: Error event mask for PMC Temperature Shutdown Alert
+ * and Power Supply.
+ * Failure Detection Errors from PMC Sysmon alarm[9].
+ * Indicates a device temperature alarm.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCSMON9		BIT(16)
+
+/**
+ * XPM_EVENT_ERROR_MASK_CFI: Error event mask for CFI Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_CFI		BIT(17)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SEUCRC: Error event mask for CFRAME SEU CRC Error.
+ */
+#define XPM_EVENT_ERROR_MASK_SEUCRC		BIT(18)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SEUECC: Error event mask for CFRAME SEU ECC Error.
+ */
+#define XPM_EVENT_ERROR_MASK_SEUECC		BIT(19)
+
+/**
+ * XPM_EVENT_ERROR_MASK_RTCALARM: Error event mask for RTC Alarm Error.
+ */
+#define XPM_EVENT_ERROR_MASK_RTCALARM		BIT(22)
+
+/**
+ * XPM_EVENT_ERROR_MASK_NPLL: Error event mask for PMC NPLL Lock Error,
+ * This error can be unmasked after the NPLL is locked to alert when the
+ * NPLL loses lock.
+ */
+#define XPM_EVENT_ERROR_MASK_NPLL		BIT(23)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PPLL: Error event mask for PMC PPLL Lock Error,
+ * This error can be unmasked after the PPLL is locked to alert when the
+ * PPLL loses lock.
+ */
+#define XPM_EVENT_ERROR_MASK_PPLL		BIT(24)
+
+/**
+ * XPM_EVENT_ERROR_MASK_CLKMON: Error event mask for Clock Monitor Errors.,
+ * Collected from CRP's CLKMON_STATUS register.
+ */
+#define XPM_EVENT_ERROR_MASK_CLKMON		BIT(25)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCTO: Error event mask for PMC Interconnect Timeout Errors.,
+ * Collected from:,Interconnect mission interrupt status register.,
+ * Interconnect latent status register.,Timeout interrupt status register
+ * for SERBs.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCTO		BIT(26)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCXMPU: Error event mask for PMC XMPU Errors:,
+ * Register access error on APB., Read permission violation.,
+ * Write permission violation.,Security violation.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCXMPU		BIT(27)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PMCXPPU: Error event mask for PMC XPPU Errors:,
+ * Register access error on APB., Master ID not found.,Read permission violation.,
+ * Master ID parity error., Master ID access violation.,
+ * TrustZone violation.,Aperture parity error.
+ */
+#define XPM_EVENT_ERROR_MASK_PMCXPPU		BIT(28)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SSIT0: Error event mask for Master SLR:
+ * SSIT Error from Slave SLR1.,
+ * For Slave SLRs: SSIT Error0 from Master SLR.
+ */
+#define XPM_EVENT_ERROR_MASK_SSIT0		BIT(29)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SSIT1: Error event mask for Master SLR:
+ * SSIT Error from Slave SLR2.,
+ * For Slave SLRs: SSIT Error1 from Master SLR.
+ */
+#define XPM_EVENT_ERROR_MASK_SSIT1		BIT(30)
+
+/**
+ * XPM_EVENT_ERROR_MASK_SSIT2: Error event mask for Master SLR:
+ * SSIT Error from Slave SLR3.,
+ * For Slave SLRs: SSIT Error2 from Master SLR.
+ */
+#define XPM_EVENT_ERROR_MASK_SSIT2		BIT(31)
+
+/*
+ * Error Event Mask belongs to PSM ERR1 node,
+ * For which Node_Id = XPM_NODETYPE_EVENT_ERROR_PSM_ERR1
+ */
+
+/**
+ * XPM_EVENT_ERROR_MASK_PS_SW_CR: Error event mask for PS Software can write to
+ * trigger register to generate this Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PS_SW_CR		BIT(0)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PS_SW_NCR: Error event mask for PS Software can write to
+ * trigger register to generate this Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PS_SW_NCR		BIT(1)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PSM_B_CR: Error event mask for PSM Firmware can write to
+ * trigger register to generate this Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PSM_B_CR		BIT(2)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PSM_B_NCR: Error event mask for PSM Firmware can write to
+ * trigger register to generate this Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_PSM_B_NCR		BIT(3)
+
+/**
+ * XPM_EVENT_ERROR_MASK_MB_FATAL: Error event mask for Or of MB Fatal1, Fatal2, Fatal3 Error.
+ */
+#define XPM_EVENT_ERROR_MASK_MB_FATAL		BIT(4)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PSM_CR: Error event mask for PSM Correctable.
+ */
+#define XPM_EVENT_ERROR_MASK_PSM_CR		BIT(5)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PSM_NCR: Error event mask for PSM Non-Correctable.
+ */
+#define XPM_EVENT_ERROR_MASK_PSM_NCR		BIT(6)
+
+/**
+ * XPM_EVENT_ERROR_MASK_OCM_ECC: Error event mask for Non-Correctable ECC Error
+ * during an OCM access.
+ */
+#define XPM_EVENT_ERROR_MASK_OCM_ECC		BIT(7)
+
+/**
+ * XPM_EVENT_ERROR_MASK_L2_ECC: Error event mask for Non-Correctable ECC Error
+ * during APU L2 Cache access.
+ */
+#define XPM_EVENT_ERROR_MASK_L2_ECC		BIT(8)
+
+/**
+ * XPM_EVENT_ERROR_MASK_RPU_ECC: Error event mask for ECC Errors during a RPU memory access.
+ * Floating-point operation exceptions. RPU REG APB error.
+ */
+#define XPM_EVENT_ERROR_MASK_RPU_ECC		BIT(9)
+
+/**
+ * XPM_EVENT_ERROR_MASK_RPU_LS: Error event mask for RPU Lockstep Errors from R5_0.
+ * The Lockstep error is not initialized until RPU clock is enabled;
+ * therefore, error outcomes are masked by default and are expected to be
+ * unmasked after processor clock is enabled and before its reset is released.
+ */
+#define XPM_EVENT_ERROR_MASK_RPU_LS		BIT(10)
+
+/**
+ * XPM_EVENT_ERROR_MASK_RPU_CCF: Error event mask for RPU Common Cause Failures ORed together.
+ * The CCF Error register with the masking capability has to reside in the RPU.
+ */
+#define XPM_EVENT_ERROR_MASK_RPU_CCF		BIT(11)
+
+/**
+ * XPM_EVENT_ERROR_MASK_GIC_AXI: Error event mask for APU GIC AXI Error by the AXI4 master port,
+ * such as SLVERR or DECERR.
+ */
+#define XPM_EVENT_ERROR_MASK_GIC_AXI		BIT(12)
+
+/**
+ * XPM_EVENT_ERROR_MASK_GIC_ECC: Error event mask for APU GIC ECC Error,
+ * a Non-Correctable ECC error occurred in any ECC-protected RAM.
+ */
+#define XPM_EVENT_ERROR_MASK_GIC_ECC		BIT(13)
+
+/**
+ * XPM_EVENT_ERROR_MASK_APLL_LOCK: Error event mask for APLL Lock Errors.
+ * The error can be unmasked after the PLL is locked to alert when the
+ * PLL loses lock.
+ */
+#define XPM_EVENT_ERROR_MASK_APLL_LOCK		BIT(14)
+
+/**
+ * XPM_EVENT_ERROR_MASK_RPLL_LOCK: Error event mask for RPLL Lock Errors.
+ * The error can be unmasked after the PLL is locked to alert when the
+ * PLL loses lock.
+ */
+#define XPM_EVENT_ERROR_MASK_RPLL_LOCK		BIT(15)
+
+/**
+ * XPM_EVENT_ERROR_MASK_CPM_CR: Error event mask for CPM Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_CPM_CR		BIT(16)
+
+/**
+ * XPM_EVENT_ERROR_MASK_CPM_NCR: Error event mask for CPM Non-Correctable Error.
+ */
+#define XPM_EVENT_ERROR_MASK_CPM_NCR		BIT(17)
+
+/**
+ * XPM_EVENT_ERROR_MASK_LPD_APB: Error event mask for LPD APB Errors
+ * from:,IPI REG,USB2 REG,CRL REG,LPD AFIFM4 REG,LPD IOU REG,
+ * LPD IOU SECURE SLCR REG,LPD SLCR REG,LPD SLCR SECURE REG.
+ */
+#define XPM_EVENT_ERROR_MASK_LPD_APB		BIT(18)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FPD_APB: Error event mask for FPD APB Errors
+ * from:,FPD AFIFM0 REG,FPD AFIFM2 REG,FPD SLCR REG,FPD SLCR SECURE REG,
+ * CRF REG.
+ */
+#define XPM_EVENT_ERROR_MASK_FPD_APB		BIT(19)
+
+/**
+ * XPM_EVENT_ERROR_MASK_LPD_PAR: Error event mask for Data parity errors
+ * from the interfaces connected
+ * to the LPD interconnect.
+ */
+#define XPM_EVENT_ERROR_MASK_LPD_PAR		BIT(20)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FPD_PAR: Error event mask for Data parity errors
+ * from the interfaces connected
+ * to the FPD interconnect.
+ */
+#define XPM_EVENT_ERROR_MASK_FPD_PAR		BIT(21)
+
+/**
+ * XPM_EVENT_ERROR_MASK_IOU_PAR: Error event mask for LPD IO Peripheral Unit Parity Error.
+ */
+#define XPM_EVENT_ERROR_MASK_IOU_PAR		BIT(22)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PSM_PAR: Error event mask for Data parity errors
+ * from the interfaces connected to the PSM interconnect.
+ */
+#define XPM_EVENT_ERROR_MASK_PSM_PAR		BIT(23)
+
+/**
+ * XPM_EVENT_ERROR_MASK_LPD_TO: Error event mask for LPD Interconnect Timeout errors.
+ * Collected from:,Timeout errors at the slaves connected to the LPD
+ * interconnect.,Address decode error.,Interconnect mission errors for
+ * the slaves connected to the LPD interconnect.
+ */
+#define XPM_EVENT_ERROR_MASK_LPD_TO		BIT(24)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FPD_TO: Error event mask for FPD Interconnect Timeout errors.
+ * Collected from:,Coresight debug trace alarms.,Timeout errors at the
+ * slaves connected to the FPD interconnect.,Address decode error.,
+ * Data parity errors on the interfaces connected to the FPD interconnect.
+ */
+#define XPM_EVENT_ERROR_MASK_FPD_TO		BIT(25)
+
+/**
+ * XPM_EVENT_ERROR_MASK_PSM_TO: Error event mask for PSM Interconnect Timeout Errors.
+ * Collected from:,Interconnect mission errors for PSM_LOCAL slave or
+ * PSM_GLOBAL slave or MDM slave or LPD interconnect or PSM master.,
+ * Interconnect latent errors for PSM_LOCAL slave or PSM_GLOBAL slave or
+ * MDM slave or LPD interconnect or PSM master.,
+ * Timeout errors at the slaves connected to the PSM interconnect.
+ */
+#define XPM_EVENT_ERROR_MASK_PSM_TO		BIT(26)
+
+/**
+ * XPM_EVENT_ERROR_MASK_XRAM_CR: Error event mask for XRAM Correctable error.
+ * Only applicable in devices that have XRAM.
+ */
+#define XPM_EVENT_ERROR_MASK_XRAM_CR		BIT(27)
+
+/**
+ * XPM_EVENT_ERROR_MASK_XRAM_NCR: Error event mask for XRAM Non-Correctable error.
+ * Only applicable in devices that have XRAM.
+ */
+#define XPM_EVENT_ERROR_MASK_XRAM_NCR		BIT(28)
+
+/*
+ * Error Event Mask belongs to PSM ERR2 node,
+ * For which Node_Id = XPM_NODETYPE_EVENT_ERROR_PSM_ERR2
+ */
+
+/**
+ * XPM_EVENT_ERROR_MASK_LPD_SWDT: Error event mask for Error from Watchdog Timer
+ * in the LPD Subsystem.
+ */
+#define XPM_EVENT_ERROR_MASK_LPD_SWDT		BIT(0)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FPD_SWDT: Error event mask for Error from Watchdog Timer
+ * in the FPD Subsystem.
+ */
+#define XPM_EVENT_ERROR_MASK_FPD_SWDT		BIT(1)
+
+/**
+ * XPM_EVENT_ERROR_MASK_LPD_XMPU: Error event mask for LPD XMPU Errors:,
+ * Register access error on APB., Read permission violation.,
+ * Write permission violation.,Security violation.
+ */
+#define XPM_EVENT_ERROR_MASK_LPD_XMPU		BIT(18)
+
+/**
+ * XPM_EVENT_ERROR_MASK_LPD_XPPU: Error event mask for LPD XPPU Errors:,
+ * Register access error on APB., Master ID not found.,Read permission violation.,
+ * Master ID parity error., Master ID access violation.,
+ * TrustZone violation.,Aperture parity error.
+ */
+#define XPM_EVENT_ERROR_MASK_LPD_XPPU		BIT(19)
+
+/**
+ * XPM_EVENT_ERROR_MASK_FPD_XMPU: Error event mask for FPD XMPU Errors:,
+ * Register access error on APB., Read permission violation.,
+ * Write permission violation.,Security violation.
+ */
+#define XPM_EVENT_ERROR_MASK_FPD_XMPU		BIT(20)
+
+/*
+ * Error Event Mask belongs to SW ERR node,
+ * For which Node_Id = XPM_NODETYPE_EVENT_ERROR_SW_ERR
+ */
+
+/**
+ * XPM_EVENT_ERROR_MASK_HB_MON_0: Health Boot Monitoring errors.
+ */
+#define XPM_EVENT_ERROR_MASK_HB_MON_0		BIT(0)
+
+/**
+ * XPM_EVENT_ERROR_MASK_HB_MON_1: Health Boot Monitoring errors.
+ */
+#define XPM_EVENT_ERROR_MASK_HB_MON_1		BIT(1)
+
+/**
+ * XPM_EVENT_ERROR_MASK_HB_MON_2: Health Boot Monitoring errors.
+ */
+#define XPM_EVENT_ERROR_MASK_HB_MON_2		BIT(2)
+
+/**
+ * XPM_EVENT_ERROR_MASK_HB_MON_3: Health Boot Monitoring errors.
+ */
+#define XPM_EVENT_ERROR_MASK_HB_MON_3		BIT(3)
+
+#endif /* _FIRMWARE_XLNX_ERROR_EVENTS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/firmware/xlnx-event-manager.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/firmware/xlnx-event-manager.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _FIRMWARE_XLNX_EVENT_MANAGER_H_
+#define _FIRMWARE_XLNX_EVENT_MANAGER_H_
+
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#define CB_MAX_PAYLOAD_SIZE	(4U) /*In payload maximum 32bytes */
+
+/************************** Exported Function *****************************/
+
+typedef void (*event_cb_func_t)(const u32 *payload, void *data);
+
+#if IS_REACHABLE(CONFIG_XLNX_EVENT_MANAGER)
+int xlnx_register_event(const enum pm_api_cb_id cb_type, const u32 node_id,
+			const u32 event, const bool wake,
+			event_cb_func_t cb_fun, void *data);
+
+int xlnx_unregister_event(const enum pm_api_cb_id cb_type, const u32 node_id,
+			  const u32 event, event_cb_func_t cb_fun);
+#else
+static inline int xlnx_register_event(const enum pm_api_cb_id cb_type, const u32 node_id,
+				      const u32 event, const bool wake,
+				      event_cb_func_t cb_fun, void *data)
+{
+	return -ENODEV;
+}
+
+static inline int xlnx_unregister_event(const enum pm_api_cb_id cb_type, const u32 node_id,
+					const u32 event, event_cb_func_t cb_fun)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /* _FIRMWARE_XLNX_EVENT_MANAGER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/firmware/xlnx-zynqmp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/firmware/xlnx-zynqmp.h
@@ -2,7 +2,7 @@
 /*
  * Xilinx Zynq MPSoC Firmware layer
  *
- *  Copyright (C) 2014-2019 Xilinx
+ *  Copyright (C) 2014-2021 Xilinx
  *
  *  Michal Simek <michal.simek@xilinx.com>
  *  Davorin Mista <davorin.mista@aggios.com>
@@ -12,6 +12,7 @@
 
 #ifndef __FIRMWARE_ZYNQMP_H__
 #define __FIRMWARE_ZYNQMP_H__
+#include <linux/types.h>
 
 #include <linux/err.h>
 
@@ -29,10 +30,34 @@
 
 /* SMC SIP service Call Function Identifier Prefix */
 #define PM_SIP_SVC			0xC2000000
+
+/* PM API versions */
+#define PM_API_VERSION_2	2
+
+/* Firmware feature check version mask */
+#define FIRMWARE_VERSION_MASK		0xFFFFU
+
+/* ATF only commands */
+#define TF_A_PM_REGISTER_SGI		0xa04
 #define PM_GET_TRUSTZONE_VERSION	0xa03
 #define PM_SET_SUSPEND_MODE		0xa02
 #define GET_CALLBACK_DATA		0xa01
 
+/* NVM Commands */
+#define PM_BBRAM_WRITE_KEY		0xB01
+#define PM_BBRAM_ZEROIZE		0xB02
+#define PM_BBRAM_WRITE_USERDATA		0xB03
+#define PM_BBRAM_READ_USERDATA		0xB04
+#define PM_BBRAM_LOCK_USERDATA		0xB05
+
+/* Secure Commands */
+#define PM_WRITE_AES_KEY		0x568
+
+/* To Get UID info list */
+#define PM_GET_UID_INFO_LIST		0x705
+
+#define PM_GET_META_HEADER_INFO_LIST	0x706
+
 /* Number of 32bits values in payload */
 #define PAYLOAD_ARG_CNT	4U
 
@@ -42,7 +67,15 @@
 /* Payload size (consists of callback API ID + arguments) */
 #define CB_PAYLOAD_SIZE (CB_ARG_CNT + 1)
 
-#define ZYNQMP_PM_MAX_QOS		100U
+#define ZYNQMP_PM_MAX_LATENCY	(~0U)
+#define ZYNQMP_PM_MAX_QOS	100U
+
+/* Usage status, returned by PmGetNodeStatus */
+#define PM_USAGE_NO_MASTER			0x0U
+#define PM_USAGE_CURRENT_MASTER			0x1U
+#define PM_USAGE_OTHER_MASTER			0x2U
+#define PM_USAGE_BOTH_MASTERS			(PM_USAGE_CURRENT_MASTER | \
+						 PM_USAGE_OTHER_MASTER)
 
 #define GSS_NUM_REGS	(4)
 
@@ -63,19 +96,57 @@
  */
 #define XILINX_ZYNQMP_PM_FPGA_FULL	0x0U
 #define XILINX_ZYNQMP_PM_FPGA_PARTIAL	BIT(0)
+#define XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_DDR	BIT(1)
+#define XILINX_ZYNQMP_PM_FPGA_AUTHENTICATION_OCM	BIT(2)
+#define XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_USERKEY	BIT(3)
+#define XILINX_ZYNQMP_PM_FPGA_ENCRYPTION_DEVKEY		BIT(4)
+
+/* AIE Operation */
+#define XILINX_AIE_OPS_COL_RST				BIT(0)
+#define XILINX_AIE_OPS_SHIM_RST				BIT(1)
+#define XILINX_AIE_OPS_ENB_COL_CLK_BUFF			BIT(2)
+#define XILINX_AIE_OPS_ZEROISATION			BIT(3)
+#define XILINX_AIE_OPS_DIS_COL_CLK_BUFF			BIT(4)
+#define XILINX_AIE_OPS_ENB_AXI_MM_ERR_EVENT		BIT(5)
+#define XILINX_AIE_OPS_SET_L2_CTRL_NPI_INTR		BIT(6)
+
+enum pm_api_cb_id {
+	PM_INIT_SUSPEND_CB = 30,
+	PM_ACKNOWLEDGE_CB = 31,
+	PM_NOTIFY_CB = 32,
+};
 
 enum pm_api_id {
 	PM_GET_API_VERSION = 1,
+	PM_SET_CONFIGURATION = 2,
+	PM_GET_NODE_STATUS = 3,
+	PM_GET_OPERATING_CHARACTERISTIC = 4,
+	PM_REGISTER_NOTIFIER = 5,
+	/* API for suspending */
+	PM_REQUEST_SUSPEND = 6,
+	PM_SELF_SUSPEND = 7,
+	PM_FORCE_POWERDOWN = 8,
+	PM_ABORT_SUSPEND = 9,
+	PM_REQUEST_WAKEUP = 10,
+	PM_SET_WAKEUP_SOURCE = 11,
 	PM_SYSTEM_SHUTDOWN = 12,
 	PM_REQUEST_NODE = 13,
 	PM_RELEASE_NODE = 14,
 	PM_SET_REQUIREMENT = 15,
+	PM_SET_MAX_LATENCY = 16,
+	/* Direct control API functions: */
 	PM_RESET_ASSERT = 17,
 	PM_RESET_GET_STATUS = 18,
+	PM_MMIO_WRITE = 19,
+	PM_MMIO_READ = 20,
 	PM_PM_INIT_FINALIZE = 21,
 	PM_FPGA_LOAD = 22,
 	PM_FPGA_GET_STATUS = 23,
 	PM_GET_CHIPID = 24,
+	/* ID 25 is been used by U-boot to process secure boot images */
+	/* Secure library generic API functions */
+	PM_SECURE_SHA = 26,
+	PM_SECURE_RSA = 27,
 	PM_PINCTRL_REQUEST = 28,
 	PM_PINCTRL_RELEASE = 29,
 	PM_PINCTRL_GET_FUNCTION = 30,
@@ -93,13 +164,21 @@
 	PM_CLOCK_GETRATE = 42,
 	PM_CLOCK_SETPARENT = 43,
 	PM_CLOCK_GETPARENT = 44,
+	PM_SECURE_IMAGE = 45,
+	PM_FPGA_READ = 46,
 	PM_SECURE_AES = 47,
+	/* PM_REGISTER_ACCESS API */
+	PM_REGISTER_ACCESS = 52,
+	PM_EFUSE_ACCESS = 53,
+	PM_FPGA_GET_VERSION = 54,
+	PM_FPGA_GET_FEATURE_LIST = 55,
 	PM_FEATURE_CHECK = 63,
 };
 
 /* PMU-FW return status codes */
 enum pm_ret_status {
 	XST_PM_SUCCESS = 0,
+	XST_PM_INVALID_VERSION = 4,
 	XST_PM_NO_FEATURE = 19,
 	XST_PM_INTERNAL = 2000,
 	XST_PM_CONFLICT = 2001,
@@ -111,6 +190,12 @@
 };
 
 enum pm_ioctl_id {
+	IOCTL_GET_RPU_OPER_MODE = 0,
+	IOCTL_SET_RPU_OPER_MODE = 1,
+	IOCTL_RPU_BOOT_ADDR_CONFIG = 2,
+	IOCTL_TCM_COMB_CONFIG = 3,
+	IOCTL_SET_TAPDELAY_BYPASS = 4,
+	IOCTL_SET_SGMII_MODE = 5,
 	IOCTL_SD_DLL_RESET = 6,
 	IOCTL_SET_SD_TAPDELAY = 7,
 	IOCTL_SET_PLL_FRAC_MODE = 8,
@@ -121,8 +206,37 @@
 	IOCTL_READ_GGS = 13,
 	IOCTL_WRITE_PGGS = 14,
 	IOCTL_READ_PGGS = 15,
+	/* IOCTL for ULPI reset */
+	IOCTL_ULPI_RESET = 16,
 	/* Set healthy bit value */
 	IOCTL_SET_BOOT_HEALTH_STATUS = 17,
+	IOCTL_AFI = 18,
+	/* Probe counter read/write */
+	IOCTL_PROBE_COUNTER_READ = 19,
+	IOCTL_PROBE_COUNTER_WRITE = 20,
+	IOCTL_OSPI_MUX_SELECT = 21,
+	/* IOCTL for USB power request */
+	IOCTL_USB_SET_STATE = 22,
+	/* IOCTL to get last reset reason */
+	IOCTL_GET_LAST_RESET_REASON = 23,
+	/* AI engine NPI ISR clear */
+	IOCTL_AIE_ISR_CLEAR = 24,
+	/* Register SGI to ATF */
+	IOCTL_REGISTER_SGI = 25,
+	/* Runtime feature configuration */
+	IOCTL_SET_FEATURE_CONFIG = 26,
+	IOCTL_GET_FEATURE_CONFIG = 27,
+	/* IOCTL for Secure Read/Write Interface */
+	IOCTL_READ_REG = 28,
+	IOCTL_MASK_WRITE_REG = 29,
+	/* Dynamic SD/GEM/USB configuration */
+	IOCTL_SET_SD_CONFIG = 30,
+	IOCTL_SET_GEM_CONFIG = 31,
+	IOCTL_SET_USB_CONFIG = 32,
+	/* AIE/AIEML Operations */
+	IOCTL_AIE_OPS = 33,
+	/* IOCTL to get default/current QoS */
+	IOCTL_GET_QOS = 34,
 };
 
 enum pm_query_id {
@@ -140,6 +254,22 @@
 	PM_QID_PINCTRL_GET_PIN_GROUPS = 11,
 	PM_QID_CLOCK_GET_NUM_CLOCKS = 12,
 	PM_QID_CLOCK_GET_MAX_DIVISOR = 13,
+	PM_QID_PLD_GET_PARENT = 14,
+};
+
+enum rpu_oper_mode {
+	PM_RPU_MODE_LOCKSTEP = 0,
+	PM_RPU_MODE_SPLIT = 1,
+};
+
+enum rpu_boot_mem {
+	PM_RPU_BOOTMEM_LOVEC = 0,
+	PM_RPU_BOOTMEM_HIVEC = 1,
+};
+
+enum rpu_tcm_comb {
+	PM_RPU_TCM_SPLIT = 0,
+	PM_RPU_TCM_COMB = 1,
 };
 
 enum zynqmp_pm_reset_action {
@@ -273,6 +403,13 @@
 	ZYNQMP_PM_RESET_END = ZYNQMP_PM_RESET_PS_PL3
 };
 
+enum zynqmp_pm_abort_reason {
+	ZYNQMP_PM_ABORT_REASON_WAKEUP_EVENT = 100,
+	ZYNQMP_PM_ABORT_REASON_POWER_UNIT_BUSY = 101,
+	ZYNQMP_PM_ABORT_REASON_NO_POWERDOWN = 102,
+	ZYNQMP_PM_ABORT_REASON_UNKNOWN = 103,
+};
+
 enum zynqmp_pm_suspend_reason {
 	SUSPEND_POWER_REQUEST = 201,
 	SUSPEND_ALERT = 202,
@@ -286,8 +423,85 @@
 };
 
 enum pm_node_id {
+	NODE_UNKNOWN = 0,
+	NODE_APU = 1,
+	NODE_APU_0 = 2,
+	NODE_APU_1 = 3,
+	NODE_APU_2 = 4,
+	NODE_APU_3 = 5,
+	NODE_RPU = 6,
+	NODE_RPU_0 = 7,
+	NODE_RPU_1 = 8,
+	NODE_PLD = 9,
+	NODE_FPD = 10,
+	NODE_OCM_BANK_0 = 11,
+	NODE_OCM_BANK_1 = 12,
+	NODE_OCM_BANK_2 = 13,
+	NODE_OCM_BANK_3 = 14,
+	NODE_TCM_0_A = 15,
+	NODE_TCM_0_B = 16,
+	NODE_TCM_1_A = 17,
+	NODE_TCM_1_B = 18,
+	NODE_L2 = 19,
+	NODE_GPU_PP_0 = 20,
+	NODE_GPU_PP_1 = 21,
+	NODE_USB_0 = 22,
+	NODE_USB_1 = 23,
+	NODE_TTC_0 = 24,
+	NODE_TTC_1 = 25,
+	NODE_TTC_2 = 26,
+	NODE_TTC_3 = 27,
+	NODE_SATA = 28,
+	NODE_ETH_0 = 29,
+	NODE_ETH_1 = 30,
+	NODE_ETH_2 = 31,
+	NODE_ETH_3 = 32,
+	NODE_UART_0 = 33,
+	NODE_UART_1 = 34,
+	NODE_SPI_0 = 35,
+	NODE_SPI_1 = 36,
+	NODE_I2C_0 = 37,
+	NODE_I2C_1 = 38,
 	NODE_SD_0 = 39,
 	NODE_SD_1 = 40,
+	NODE_DP = 41,
+	NODE_GDMA = 42,
+	NODE_ADMA = 43,
+	NODE_NAND = 44,
+	NODE_QSPI = 45,
+	NODE_GPIO = 46,
+	NODE_CAN_0 = 47,
+	NODE_CAN_1 = 48,
+	NODE_EXTERN = 49,
+	NODE_APLL = 50,
+	NODE_VPLL = 51,
+	NODE_DPLL = 52,
+	NODE_RPLL = 53,
+	NODE_IOPLL = 54,
+	NODE_DDR = 55,
+	NODE_IPI_APU = 56,
+	NODE_IPI_RPU_0 = 57,
+	NODE_GPU = 58,
+	NODE_PCIE = 59,
+	NODE_PCAP = 60,
+	NODE_RTC = 61,
+	NODE_LPD = 62,
+	NODE_VCU = 63,
+	NODE_IPI_RPU_1 = 64,
+	NODE_IPI_PL_0 = 65,
+	NODE_IPI_PL_1 = 66,
+	NODE_IPI_PL_2 = 67,
+	NODE_IPI_PL_3 = 68,
+	NODE_PL = 69,
+	NODE_GEM_TSU = 70,
+	NODE_SWDT_0 = 71,
+	NODE_SWDT_1 = 72,
+	NODE_CSU = 73,
+	NODE_PJTAG = 74,
+	NODE_TRACE = 75,
+	NODE_TESTSCAN = 76,
+	NODE_PMU = 77,
+	NODE_MAX = 78,
 };
 
 enum tap_delay_type {
@@ -332,6 +546,12 @@
 	PM_PINCTRL_INPUT_TYPE_SCHMITT = 1,
 };
 
+enum zynqmp_pm_opchar_type {
+	ZYNQMP_PM_OPERATING_CHARACTERISTIC_POWER = 1,
+	ZYNQMP_PM_OPERATING_CHARACTERISTIC_ENERGY = 2,
+	ZYNQMP_PM_OPERATING_CHARACTERISTIC_TEMPERATURE = 3,
+};
+
 enum pm_pinctrl_drive_strength {
 	PM_PINCTRL_DRIVE_STRENGTH_2MA = 0,
 	PM_PINCTRL_DRIVE_STRENGTH_4MA = 1,
@@ -339,6 +559,11 @@
 	PM_PINCTRL_DRIVE_STRENGTH_12MA = 3,
 };
 
+enum pm_pinctrl_tri_state {
+	PM_PINCTRL_TRI_STATE_DISABLE = 0,
+	PM_PINCTRL_TRI_STATE_ENABLE = 1,
+};
+
 enum zynqmp_pm_shutdown_type {
 	ZYNQMP_PM_SHUTDOWN_TYPE_SHUTDOWN = 0,
 	ZYNQMP_PM_SHUTDOWN_TYPE_RESET = 1,
@@ -351,6 +576,68 @@
 	ZYNQMP_PM_SHUTDOWN_SUBTYPE_SYSTEM = 2,
 };
 
+enum tap_delay_signal_type {
+	PM_TAPDELAY_NAND_DQS_IN = 0,
+	PM_TAPDELAY_NAND_DQS_OUT = 1,
+	PM_TAPDELAY_QSPI = 2,
+	PM_TAPDELAY_MAX = 3,
+};
+
+enum tap_delay_bypass_ctrl {
+	PM_TAPDELAY_BYPASS_DISABLE = 0,
+	PM_TAPDELAY_BYPASS_ENABLE = 1,
+};
+
+enum sgmii_mode {
+	PM_SGMII_DISABLE = 0,
+	PM_SGMII_ENABLE = 1,
+};
+
+enum pm_register_access_id {
+	CONFIG_REG_WRITE = 0,
+	CONFIG_REG_READ = 1,
+};
+
+enum pm_reset_reason {
+	PM_RESET_REASON_EXT_POR = 0,
+	PM_RESET_REASON_SW_POR = 1,
+	PM_RESET_REASON_SLR_POR = 2,
+	PM_RESET_REASON_ERR_POR = 3,
+	PM_RESET_REASON_DAP_SRST = 7,
+	PM_RESET_REASON_ERR_SRST = 8,
+	PM_RESET_REASON_SW_SRST = 9,
+	PM_RESET_REASON_SLR_SRST = 10,
+};
+
+enum pm_feature_config_id {
+	PM_FEATURE_INVALID = 0,
+	PM_FEATURE_OVERTEMP_STATUS = 1,
+	PM_FEATURE_OVERTEMP_VALUE = 2,
+	PM_FEATURE_EXTWDT_STATUS = 3,
+	PM_FEATURE_EXTWDT_VALUE = 4,
+};
+
+enum pm_sd_config_type {
+	SD_CONFIG_EMMC_SEL = 1, /* To set SD_EMMC_SEL in CTRL_REG_SD and SD_SLOTTYPE */
+	SD_CONFIG_BASECLK = 2, /* To set SD_BASECLK in SD_CONFIG_REG1 */
+	SD_CONFIG_8BIT = 3, /* To set SD_8BIT in SD_CONFIG_REG2 */
+	SD_CONFIG_FIXED = 4, /* To set fixed config registers */
+};
+
+enum pm_gem_config_type {
+	GEM_CONFIG_SGMII_MODE = 1, /* To set GEM_SGMII_MODE in GEM_CLK_CTRL register */
+	GEM_CONFIG_FIXED = 2, /* To set fixed config registers */
+};
+
+enum pm_usb_config_type {
+	USB_CONFIG_FIXED = 1, /* To set fixed config registers */
+};
+
+enum ospi_mux_select_type {
+	PM_OSPI_MUX_SEL_DMA = 0,
+	PM_OSPI_MUX_SEL_LINEAR = 1,
+};
+
 /**
  * struct zynqmp_pm_query_data - PM query data
  * @qid:	query ID
@@ -366,7 +653,7 @@
 };
 
 int zynqmp_pm_invoke_fn(u32 pm_api_id, u32 arg0, u32 arg1,
-			u32 arg2, u32 arg3, u32 *ret_payload);
+			u32 arg2, u32 arg3, u32 arg4, u32 *ret_payload);
 
 #if IS_REACHABLE(CONFIG_ZYNQMP_FIRMWARE)
 int zynqmp_pm_get_api_version(u32 *version);
@@ -387,9 +674,12 @@
 int zynqmp_pm_get_pll_frac_data(u32 clk_id, u32 *data);
 int zynqmp_pm_set_sd_tapdelay(u32 node_id, u32 type, u32 value);
 int zynqmp_pm_sd_dll_reset(u32 node_id, u32 type);
-int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+int zynqmp_pm_ospi_mux_select(u32 dev_id, u32 select);
+int zynqmp_pm_reset_assert(const u32 reset,
 			   const enum zynqmp_pm_reset_action assert_flag);
-int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, u32 *status);
+int zynqmp_pm_reset_get_status(const u32 reset, u32 *status);
+unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode);
+int zynqmp_pm_bootmode_write(u32 ps_mode);
 int zynqmp_pm_init_finalize(void);
 int zynqmp_pm_set_suspend_mode(u32 mode);
 int zynqmp_pm_request_node(const u32 node, const u32 capabilities,
@@ -399,14 +689,62 @@
 			      const u32 qos,
 			      const enum zynqmp_pm_request_ack ack);
 int zynqmp_pm_aes_engine(const u64 address, u32 *out);
-int zynqmp_pm_fpga_load(const u64 address, const u32 size, const u32 flags);
+int zynqmp_pm_efuse_access(const u64 address, u32 *out);
+int zynqmp_pm_secure_load(const u64 src_addr, u64 key_addr, u64 *dst);
+int zynqmp_pm_write_aes_key(const u32 keylen, const u32 keysrc, const u64 keyaddr);
+int zynqmp_pm_bbram_write_usrdata(u32 data);
+int zynqmp_pm_bbram_read_usrdata(const u64 outaddr);
+int zynqmp_pm_bbram_write_aeskey(u32 keylen, const u64 keyaddr);
+int zynqmp_pm_bbram_zeroize(void);
+int zynqmp_pm_bbram_lock_userdata(void);
+int zynqmp_pm_fpga_read(const u32 reg_numframes, const u64 phys_address,
+			u32 readback_type, u32 *value);
+int zynqmp_pm_sha_hash(const u64 address, const u32 size, const u32 flags);
+int zynqmp_pm_rsa(const u64 address, const u32 size, const u32 flags);
+int zynqmp_pm_config_reg_access(u32 register_access_id, u32 address, u32 mask,
+				u32 value, u32 *out);
+int zynqmp_pm_mmio_read(u32 address, u32 *out);
+int zynqmp_pm_mmio_write(u32 address, u32 mask, u32 value);
+int zynqmp_pm_request_suspend(const u32 node, const enum zynqmp_pm_request_ack ack,
+			      const u32 latency, const u32 state);
+int zynqmp_pm_set_max_latency(const u32 node, const u32 latency);
+int zynqmp_pm_set_configuration(const u32 physical_addr);
+int zynqmp_pm_get_node_status(const u32 node, u32 *const status,
+			      u32 *const requirements, u32 *const usage);
+int zynqmp_pm_get_operating_characteristic(const u32 node,
+					   const enum zynqmp_pm_opchar_type type,
+					   u32 *const result);
+int zynqmp_pm_force_powerdown(const u32 target, const enum zynqmp_pm_request_ack ack);
+int zynqmp_pm_request_wakeup(const u32 node, const bool set_addr,
+			     const u64 address, const enum zynqmp_pm_request_ack ack);
+int zynqmp_pm_set_wakeup_source(const u32 target, const u32 wakeup_node, const u32 enable);
+int zynqmp_pm_fpga_load(const u64 address, const u32 size,
+			const u32 flags, u32 *status);
 int zynqmp_pm_fpga_get_status(u32 *value);
 int zynqmp_pm_write_ggs(u32 index, u32 value);
 int zynqmp_pm_read_ggs(u32 index, u32 *value);
 int zynqmp_pm_write_pggs(u32 index, u32 value);
 int zynqmp_pm_read_pggs(u32 index, u32 *value);
+int zynqmp_pm_usb_set_state(u32 node, u32 state, u32 value);
+int zynqmp_pm_afi(u32 index, u32 value);
+int zynqmp_pm_set_tapdelay_bypass(u32 index, u32 value);
+int zynqmp_pm_set_sgmii_mode(u32 enable);
+int zynqmp_pm_ulpi_reset(void);
+int zynqmp_pm_probe_counter_read(u32 domain, u32 reg, u32 *value);
+int zynqmp_pm_probe_counter_write(u32 domain, u32 reg, u32 value);
+int zynqmp_pm_get_last_reset_reason(u32 *reset_reason);
 int zynqmp_pm_system_shutdown(const u32 type, const u32 subtype);
 int zynqmp_pm_set_boot_health_status(u32 value);
+int zynqmp_pm_force_pwrdwn(const u32 target,
+			   const enum zynqmp_pm_request_ack ack);
+int zynqmp_pm_request_wake(const u32 node,
+			   const bool set_addr,
+			   const u64 address,
+			   const enum zynqmp_pm_request_ack ack);
+int zynqmp_pm_get_rpu_mode(u32 node_id, enum rpu_oper_mode *rpu_mode);
+int zynqmp_pm_set_rpu_mode(u32 node_id, u32 arg1);
+int zynqmp_pm_set_tcm_config(u32 node_id, u32 arg1);
+int zynqmp_pm_clear_aie_npi_isr(u32 node, u32 irq_mask);
 int zynqmp_pm_pinctrl_request(const u32 pin);
 int zynqmp_pm_pinctrl_release(const u32 pin);
 int zynqmp_pm_pinctrl_get_function(const u32 pin, u32 *id);
@@ -416,6 +754,28 @@
 int zynqmp_pm_pinctrl_set_config(const u32 pin, const u32 param,
 				 u32 value);
 int zynqmp_pm_load_pdi(const u32 src, const u64 address);
+int zynqmp_pm_register_notifier(const u32 node, const u32 event,
+				const u32 wake, const u32 enable);
+int zynqmp_pm_feature(const u32 api_id);
+int zynqmp_pm_is_function_supported(const u32 api_id, const u32 id);
+int zynqmp_pm_set_feature_config(enum pm_feature_config_id id, u32 value);
+int zynqmp_pm_get_feature_config(enum pm_feature_config_id id, u32 *payload);
+int zynqmp_pm_get_uid_info(const u64 address, const u32 size, u32 *count);
+int zynqmp_pm_sec_read_reg(u32 node_id, u32 offset, u32 *ret_value);
+int zynqmp_pm_sec_mask_write_reg(const u32 node_id, const u32 offset,
+				 u32 mask, u32 value);
+int zynqmp_pm_set_sd_config(u32 node, enum pm_sd_config_type config, u32 value);
+int zynqmp_pm_set_gem_config(u32 node, enum pm_gem_config_type config,
+			     u32 value);
+int zynqmp_pm_set_usb_config(u32 node, enum pm_usb_config_type config,
+			     u32 value);
+int zynqmp_pm_get_meta_header(const u64 src, const u64 dst,
+			      const u32 size, u32 *count);
+int zynqmp_pm_register_sgi(u32 sgi_num, u32 reset);
+int zynqmp_pm_aie_operation(u32 node, u16 start_col, u16 num_col, u32 operation);
+int zynqmp_pm_fpga_get_version(u32 *value);
+int zynqmp_pm_fpga_get_feature_list(u32 *value);
+int zynqmp_pm_get_qos(u32 node, u32 *const def_qos, u32 *const qos);
 #else
 static inline int zynqmp_pm_get_api_version(u32 *version)
 {
@@ -508,18 +868,33 @@
 	return -ENODEV;
 }
 
-static inline int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+static inline int zynqmp_pm_ospi_mux_select(u32 dev_id, u32 select)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_reset_assert(const u32 reset,
 					 const enum zynqmp_pm_reset_action assert_flag)
 {
 	return -ENODEV;
 }
 
-static inline int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
+static inline int zynqmp_pm_reset_get_status(const u32 reset,
 					     u32 *status)
 {
 	return -ENODEV;
 }
 
+static inline unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bootmode_write(u32 ps_mode)
+{
+	return -ENODEV;
+}
+
 static inline int zynqmp_pm_init_finalize(void)
 {
 	return -ENODEV;
@@ -556,7 +931,7 @@
 }
 
 static inline int zynqmp_pm_fpga_load(const u64 address, const u32 size,
-				      const u32 flags)
+				      const u32 flags, u32 *status)
 {
 	return -ENODEV;
 }
@@ -586,6 +961,31 @@
 	return -ENODEV;
 }
 
+static inline int zynqmp_pm_usb_set_state(u32 node, u32 state, u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_afi(u32 index, u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_tapdelay_bypass(u32 index, u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_sgmii_mode(u32 enable)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_ulpi_reset(void)
+{
+	return -ENODEV;
+}
+
 static inline int zynqmp_pm_system_shutdown(const u32 type, const u32 subtype)
 {
 	return -ENODEV;
@@ -596,6 +996,40 @@
 	return -ENODEV;
 }
 
+static inline int zynqmp_pm_force_pwrdwn(const u32 target,
+					 const enum zynqmp_pm_request_ack ack)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_request_wake(const u32 node,
+					 const bool set_addr,
+					 const u64 address,
+					 const enum zynqmp_pm_request_ack ack)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_rpu_mode(u32 node_id, enum rpu_oper_mode *rpu_mode)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_rpu_mode(u32 node_id, u32 arg1)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_tcm_config(u32 node_id, u32 arg1)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_clear_aie_npi_isr(u32 node, u32 irq_mask)
+{
+	return -ENODEV;
+}
+
 static inline int zynqmp_pm_pinctrl_request(const u32 pin)
 {
 	return -ENODEV;
@@ -611,6 +1045,11 @@
 	return -ENODEV;
 }
 
+static inline int zynqmp_pm_is_function_supported(const u32 api_id, const u32 id)
+{
+	return -ENODEV;
+}
+
 static inline int zynqmp_pm_pinctrl_set_function(const u32 pin, const u32 id)
 {
 	return -ENODEV;
@@ -632,6 +1071,241 @@
 {
 	return -ENODEV;
 }
+
+static inline int zynqmp_pm_efuse_access(const u64 address, u32 *out)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_sha_hash(const u64 address, const u32 size,
+				     const u32 flags)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_rsa(const u64 address, const u32 size,
+				const u32 flags)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_config_reg_access(u32 register_access_id,
+					      u32 address, u32 mask, u32 value,
+					      u32 *out)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_mmio_write(u32 address, u32 mask, u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_mmio_read(u32 address, u32 *out)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_request_suspend(const u32 node,
+					    const enum zynqmp_pm_request_ack ack,
+					    const u32 latency, const u32 state)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_max_latency(const u32 node, const u32 latency)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_configuration(const u32 physical_addr)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_node_status(const u32 node, u32 *const status,
+					    u32 *const requirements,
+					    u32 *const usage)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_operating_characteristic(const u32 node,
+							 const enum zynqmp_pm_opchar_type type,
+							 u32 *const result)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_force_powerdown(const u32 target,
+					    const enum zynqmp_pm_request_ack ack)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_request_wakeup(const u32 node, const bool set_addr,
+					   const u64 address,
+					   const enum zynqmp_pm_request_ack ack)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_wakeup_source(const u32 target,
+					      const u32 wakeup_node,
+					      const u32 enable)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_fpga_read(const u32 reg_numframes,
+				      const u64 phys_address, u32 readback_type,
+				      u32 *value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_write_aes_key(const u32 keylen, const u32 keysrc, const u64 keyaddr)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bbram_write_usrdata(u32 data)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bbram_read_usrdata(const u64 outaddr)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bbram_write_aeskey(const u64 keyaddr, u16 keylen)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bbram_zeroize(void)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bbram_lock_userdata(void)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_probe_counter_read(u32 deviceid, u32 reg, u32 *value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_probe_counter_write(u32 domain, u32 reg, u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_secure_load(const u64 src_addr, u64 key_addr, u64 *dst)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_last_reset_reason(u32 *reset_reason)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_register_notifier(const u32 node, const u32 event,
+					      const u32 wake, const u32 enable)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_feature(const u32 api_id)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_feature_config(enum pm_feature_config_id id,
+					       u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_feature_config(enum pm_feature_config_id id,
+					       u32 *payload)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_uid_info(const u64 address, const u32 size,
+					 u32 *count)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_sec_read_reg(u32 node_id, u32 offset, u32 *ret_value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_sec_mask_write_reg(const u32 node_id, const u32 offset,
+					u32 mask, u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_sd_config(u32 node,
+					  enum pm_sd_config_type config,
+					  u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_qos(u32 node, u32 *const def_qos, u32 *const qos)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_gem_config(u32 node,
+					   enum pm_gem_config_type config,
+					   u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_set_usb_config(u32 node,
+					   enum pm_usb_config_type config,
+					   u32 value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_get_meta_header(const u64 src, const u64 dst,
+					    const u32 size, u32 *count)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_register_sgi(u32 sgi_num, u32 reset)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_aie_operation(u32 node, u16 start_col,
+					  u16 num_col, u32 operation)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_fpga_get_version(u32 *value)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_fpga_get_feature_list(u32 *value)
+{
+	return -ENODEV;
+}
 #endif
 
 #endif /* __FIRMWARE_ZYNQMP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fortify-string.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fortify-string.h
@@ -280,7 +280,10 @@
 	if (p_size == (size_t)-1 && q_size == (size_t)-1)
 		return __underlying_strcpy(p, q);
 	size = strlen(q) + 1;
-	/* test here to use the more stringent object size */
+	/* Compile-time check for const size overflow. */
+	if (__builtin_constant_p(size) && p_size < size)
+		__write_overflow();
+	/* Run-time check for dynamic size overflow. */
 	if (p_size < size)
 		fortify_panic(__func__);
 	memcpy(p, q, size);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fpga/fpga-mgr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fpga/fpga-mgr.h
@@ -9,8 +9,11 @@
 #define _LINUX_FPGA_MGR_H
 
 #include <linux/mutex.h>
+#include <linux/miscdevice.h>
 #include <linux/platform_device.h>
 
+#define ENCRYPTED_KEY_LEN	64 /* Bytes */
+
 struct fpga_manager;
 struct sg_table;
 
@@ -62,17 +65,29 @@
  *
  * %FPGA_MGR_EXTERNAL_CONFIG: FPGA has been configured prior to Linux booting
  *
- * %FPGA_MGR_ENCRYPTED_BITSTREAM: indicates bitstream is encrypted
+ * %FPGA_MGR_ENCRYPTED_BITSTREAM: indicates bitstream is encrypted with
+ *				  device key
  *
  * %FPGA_MGR_BITSTREAM_LSB_FIRST: SPI bitstream bit order is LSB first
  *
  * %FPGA_MGR_COMPRESSED_BITSTREAM: FPGA bitstream is compressed
+ *
+ * %FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM: indicates bitstream is encrypted with
+ *					  user key
+ * %FPGA_MGR_DDR_MEM_AUTH_BITSTREAM: do bitstream authentication using DDR
+ *				     memory if supported
+ * %FPGA_MGR_SECURE_MEM_AUTH_BITSTREAM: do bitstream authentication using secure
+ *					memory if supported
  */
 #define FPGA_MGR_PARTIAL_RECONFIG	BIT(0)
 #define FPGA_MGR_EXTERNAL_CONFIG	BIT(1)
 #define FPGA_MGR_ENCRYPTED_BITSTREAM	BIT(2)
 #define FPGA_MGR_BITSTREAM_LSB_FIRST	BIT(3)
 #define FPGA_MGR_COMPRESSED_BITSTREAM	BIT(4)
+#define FPGA_MGR_USERKEY_ENCRYPTED_BITSTREAM	BIT(5)
+#define FPGA_MGR_DDR_MEM_AUTH_BITSTREAM		BIT(6)
+#define FPGA_MGR_SECURE_MEM_AUTH_BITSTREAM	BIT(7)
+#define FPGA_MGR_CONFIG_DMA_BUF			BIT(8)
 
 /**
  * struct fpga_image_info - information specific to an FPGA image
@@ -82,6 +97,7 @@
  * @config_complete_timeout_us: maximum time for FPGA to switch to operating
  *	   status in the write_complete op.
  * @firmware_name: name of FPGA image firmware file
+ * @key: key value useful for Encrypted Bitstream loading to read the userkey
  * @sgt: scatter/gather table containing FPGA image
  * @buf: contiguous buffer containing FPGA image
  * @count: size of buf
@@ -95,6 +111,7 @@
 	u32 disable_timeout_us;
 	u32 config_complete_timeout_us;
 	char *firmware_name;
+	char key[ENCRYPTED_KEY_LEN];
 	struct sg_table *sgt;
 	const char *buf;
 	size_t count;
@@ -114,6 +131,7 @@
  * @write: write count bytes of configuration data to the FPGA
  * @write_sg: write the scatter list of configuration data to the FPGA
  * @write_complete: set FPGA to operating state after writing is done
+ * @read: optional: read FPGA configuration information
  * @fpga_remove: optional: Set FPGA into a specific state during driver remove
  * @groups: optional attribute groups.
  *
@@ -132,6 +150,7 @@
 	int (*write_sg)(struct fpga_manager *mgr, struct sg_table *sgt);
 	int (*write_complete)(struct fpga_manager *mgr,
 			      struct fpga_image_info *info);
+	int (*read)(struct fpga_manager *mgr, struct seq_file *s);
 	void (*fpga_remove)(struct fpga_manager *mgr);
 	const struct attribute_group **groups;
 };
@@ -142,6 +161,12 @@
 #define FPGA_MGR_STATUS_INCOMPATIBLE_IMAGE_ERR	BIT(2)
 #define FPGA_MGR_STATUS_IP_PROTOCOL_ERR		BIT(3)
 #define FPGA_MGR_STATUS_FIFO_OVERFLOW_ERR	BIT(4)
+#define FPGA_MGR_STATUS_SECURITY_ERR		BIT(5)
+#define FPGA_MGR_STATUS_DEVICE_INIT_ERR		BIT(6)
+#define FPGA_MGR_STATUS_SIGNAL_ERR		BIT(7)
+#define FPGA_MGR_STATUS_HIGH_Z_STATE_ERR	BIT(8)
+#define FPGA_MGR_STATUS_EOS_ERR			BIT(9)
+#define FPGA_MGR_STATUS_FIRMWARE_REQ_ERR	BIT(10)
 
 /**
  * struct fpga_compat_id - id for compatibility check
@@ -157,21 +182,35 @@
 /**
  * struct fpga_manager - fpga manager structure
  * @name: name of low level fpga manager
+ * @flags: flags determines the type of Bitstream
+ * @key: key value useful for Encrypted Bitstream loading to read the userkey
  * @dev: fpga manager device
+ * @miscdev: information about character device node
+ * @dmabuf: shared dma buffer
  * @ref_mutex: only allows one reference to fpga manager
  * @state: state of fpga manager
  * @compat_id: FPGA manager id for compatibility check.
  * @mops: pointer to struct of fpga manager ops
  * @priv: low level driver private date
+ * @err: low level driver error code
+ * @dir: debugfs image directory
  */
 struct fpga_manager {
 	const char *name;
+	unsigned long flags;
+	char key[ENCRYPTED_KEY_LEN + 1];
 	struct device dev;
+	struct miscdevice miscdev;
+	struct dma_buf *dmabuf;
 	struct mutex ref_mutex;
 	enum fpga_mgr_states state;
 	struct fpga_compat_id *compat_id;
 	const struct fpga_manager_ops *mops;
 	void *priv;
+	int err;
+#ifdef CONFIG_FPGA_MGR_DEBUG_FS
+	struct dentry *dir;
+#endif
 };
 
 #define to_fpga_manager(d) container_of(d, struct fpga_manager, dev)
@@ -204,4 +243,6 @@
 					  const struct fpga_manager_ops *mops,
 					  void *priv);
 
+#define FPGA_IOCTL_LOAD_DMA_BUFF	_IOWR('R', 1, __u32)
+
 #endif /*_LINUX_FPGA_MGR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fpga/fpga-region.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fpga/fpga-region.h
@@ -7,6 +7,27 @@
 #include <linux/fpga/fpga-mgr.h>
 #include <linux/fpga/fpga-bridge.h>
 
+struct fpga_region;
+
+/**
+ * struct fpga_region_info - collection of parameters an FPGA Region
+ * @mgr: fpga region manager
+ * @compat_id: FPGA region id for compatibility check.
+ * @priv: fpga region private data
+ * @get_bridges: optional function to get bridges to a list
+ *
+ * fpga_region_info contains parameters for the register_full function.
+ * These are separated into an info structure because they some are optional
+ * others could be added to in the future. The info structure facilitates
+ * maintaining a stable API.
+ */
+struct fpga_region_info {
+	struct fpga_manager *mgr;
+	struct fpga_compat_id *compat_id;
+	void *priv;
+	int (*get_bridges)(struct fpga_region *region);
+};
+
 /**
  * struct fpga_region - FPGA Region structure
  * @dev: FPGA Region device
@@ -15,6 +36,7 @@
  * @mgr: FPGA manager
  * @info: FPGA image info
  * @compat_id: FPGA region id for compatibility check.
+ * @ops_owner: module containing the get_bridges function
  * @priv: private data
  * @get_bridges: optional function to get bridges to a list
  */
@@ -25,6 +47,7 @@
 	struct fpga_manager *mgr;
 	struct fpga_image_info *info;
 	struct fpga_compat_id *compat_id;
+	struct module *ops_owner;
 	void *priv;
 	int (*get_bridges)(struct fpga_region *region);
 };
@@ -37,15 +60,17 @@
 
 int fpga_region_program_fpga(struct fpga_region *region);
 
-struct fpga_region
-*fpga_region_create(struct device *dev, struct fpga_manager *mgr,
-		    int (*get_bridges)(struct fpga_region *));
-void fpga_region_free(struct fpga_region *region);
-int fpga_region_register(struct fpga_region *region);
+#define fpga_region_register_full(parent, info) \
+	__fpga_region_register_full(parent, info, THIS_MODULE)
+struct fpga_region *
+__fpga_region_register_full(struct device *parent, const struct fpga_region_info *info,
+			    struct module *owner);
+
+#define fpga_region_register(parent, mgr, get_bridges) \
+	__fpga_region_register(parent, mgr, get_bridges, THIS_MODULE)
+struct fpga_region *
+__fpga_region_register(struct device *parent, struct fpga_manager *mgr,
+		       int (*get_bridges)(struct fpga_region *), struct module *owner);
 void fpga_region_unregister(struct fpga_region *region);
 
-struct fpga_region
-*devm_fpga_region_create(struct device *dev, struct fpga_manager *mgr,
-			int (*get_bridges)(struct fpga_region *));
-
 #endif /* _FPGA_REGION_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fs.h
@@ -41,6 +41,7 @@
 #include <linux/stddef.h>
 #include <linux/mount.h>
 #include <linux/cred.h>
+#include <linux/mnt_idmapping.h>
 
 #include <asm/byteorder.h>
 #include <uapi/linux/fs.h>
@@ -77,10 +78,8 @@
 extern void __init files_init(void);
 extern void __init files_maxfiles_init(void);
 
-extern struct files_stat_struct files_stat;
 extern unsigned long get_max_files(void);
 extern unsigned int sysctl_nr_open;
-extern struct inodes_stat_t inodes_stat;
 extern int leases_enable, lease_break_time;
 extern int sysctl_protected_symlinks;
 extern int sysctl_protected_hardlinks;
@@ -321,6 +320,8 @@
 #define IOCB_NOIO		(1 << 20)
 /* can use bio alloc cache */
 #define IOCB_ALLOC_CACHE	(1 << 21)
+/* kiocb is a read or write operation submitted by fs/aio.c. */
+#define IOCB_AIO_RW		(1 << 23)
 
 struct kiocb {
 	struct file		*ki_filp;
@@ -467,11 +468,11 @@
 	atomic_t		nr_thps;
 #endif
 	struct rb_root_cached	i_mmap;
-	struct rw_semaphore	i_mmap_rwsem;
 	unsigned long		nrpages;
 	pgoff_t			writeback_index;
 	const struct address_space_operations *a_ops;
 	unsigned long		flags;
+	struct rw_semaphore	i_mmap_rwsem;
 	errseq_t		wb_err;
 	spinlock_t		private_lock;
 	struct list_head	private_list;
@@ -1063,6 +1064,7 @@
 };
 
 struct lock_manager_operations {
+	void *lm_mod_owner;
 	fl_owner_t (*lm_get_owner)(fl_owner_t);
 	void (*lm_put_owner)(fl_owner_t);
 	void (*lm_notify)(struct file_lock *);	/* unblock callback */
@@ -1071,6 +1073,8 @@
 	int (*lm_change)(struct file_lock *, int, struct list_head *);
 	void (*lm_setup)(struct file_lock *, void **);
 	bool (*lm_breaker_owns_lease)(struct file_lock *);
+	bool (*lm_lock_expirable)(struct file_lock *cfl);
+	void (*lm_expire_lock)(void);
 };
 
 struct lock_manager {
@@ -1194,6 +1198,7 @@
 extern int vfs_test_lock(struct file *, struct file_lock *);
 extern int vfs_lock_file(struct file *, unsigned int, struct file_lock *, struct file_lock *);
 extern int vfs_cancel_lock(struct file *filp, struct file_lock *fl);
+bool vfs_inode_has_locks(struct inode *inode);
 extern int locks_lock_inode_wait(struct inode *inode, struct file_lock *fl);
 extern int __break_lease(struct inode *inode, unsigned int flags, unsigned int type);
 extern void lease_get_mtime(struct inode *, struct timespec64 *time);
@@ -1208,6 +1213,15 @@
 struct files_struct;
 extern void show_fd_locks(struct seq_file *f,
 			 struct file *filp, struct files_struct *files);
+extern bool locks_owner_has_blockers(struct file_lock_context *flctx,
+			fl_owner_t owner);
+
+static inline struct file_lock_context *
+locks_inode_context(const struct inode *inode)
+{
+	return smp_load_acquire(&inode->i_flctx);
+}
+
 #else /* !CONFIG_FILE_LOCKING */
 static inline int fcntl_getlk(struct file *file, unsigned int cmd,
 			      struct flock __user *user)
@@ -1306,6 +1320,11 @@
 	return 0;
 }
 
+static inline bool vfs_inode_has_locks(struct inode *inode)
+{
+	return false;
+}
+
 static inline int locks_lock_inode_wait(struct inode *inode, struct file_lock *fl)
 {
 	return -ENOLCK;
@@ -1343,6 +1362,18 @@
 struct files_struct;
 static inline void show_fd_locks(struct seq_file *f,
 			struct file *filp, struct files_struct *files) {}
+static inline bool locks_owner_has_blockers(struct file_lock_context *flctx,
+			fl_owner_t owner)
+{
+	return false;
+}
+
+static inline struct file_lock_context *
+locks_inode_context(const struct inode *inode)
+{
+	return NULL;
+}
+
 #endif /* !CONFIG_FILE_LOCKING */
 
 static inline struct inode *file_inode(const struct file *f)
@@ -1381,6 +1412,7 @@
 /* can be called from interrupts */
 extern void kill_fasync(struct fasync_struct **, int, int);
 
+extern int setfl(int fd, struct file *filp, unsigned long arg);
 extern void __f_setown(struct file *filp, struct pid *, enum pid_type, int force);
 extern int f_setown(struct file *filp, unsigned long arg, int force);
 extern void f_delown(struct file *filp);
@@ -1391,29 +1423,29 @@
  * sb->s_flags.  Note that these mirror the equivalent MS_* flags where
  * represented in both.
  */
-#define SB_RDONLY	 1	/* Mount read-only */
-#define SB_NOSUID	 2	/* Ignore suid and sgid bits */
-#define SB_NODEV	 4	/* Disallow access to device special files */
-#define SB_NOEXEC	 8	/* Disallow program execution */
-#define SB_SYNCHRONOUS	16	/* Writes are synced at once */
-#define SB_MANDLOCK	64	/* Allow mandatory locks on an FS */
-#define SB_DIRSYNC	128	/* Directory modifications are synchronous */
-#define SB_NOATIME	1024	/* Do not update access times. */
-#define SB_NODIRATIME	2048	/* Do not update directory access times */
-#define SB_SILENT	32768
-#define SB_POSIXACL	(1<<16)	/* VFS does not apply the umask */
-#define SB_INLINECRYPT	(1<<17)	/* Use blk-crypto for encrypted files */
-#define SB_KERNMOUNT	(1<<22) /* this is a kern_mount call */
-#define SB_I_VERSION	(1<<23) /* Update inode I_version field */
-#define SB_LAZYTIME	(1<<25) /* Update the on-disk [acm]times lazily */
+#define SB_RDONLY       BIT(0)	/* Mount read-only */
+#define SB_NOSUID       BIT(1)	/* Ignore suid and sgid bits */
+#define SB_NODEV        BIT(2)	/* Disallow access to device special files */
+#define SB_NOEXEC       BIT(3)	/* Disallow program execution */
+#define SB_SYNCHRONOUS  BIT(4)	/* Writes are synced at once */
+#define SB_MANDLOCK     BIT(6)	/* Allow mandatory locks on an FS */
+#define SB_DIRSYNC      BIT(7)	/* Directory modifications are synchronous */
+#define SB_NOATIME      BIT(10)	/* Do not update access times. */
+#define SB_NODIRATIME   BIT(11)	/* Do not update directory access times */
+#define SB_SILENT       BIT(15)
+#define SB_POSIXACL     BIT(16)	/* VFS does not apply the umask */
+#define SB_INLINECRYPT  BIT(17)	/* Use blk-crypto for encrypted files */
+#define SB_KERNMOUNT    BIT(22)	/* this is a kern_mount call */
+#define SB_I_VERSION    BIT(23)	/* Update inode I_version field */
+#define SB_LAZYTIME     BIT(25)	/* Update the on-disk [acm]times lazily */
 
 /* These sb flags are internal to the kernel */
-#define SB_SUBMOUNT     (1<<26)
-#define SB_FORCE    	(1<<27)
-#define SB_NOSEC	(1<<28)
-#define SB_BORN		(1<<29)
-#define SB_ACTIVE	(1<<30)
-#define SB_NOUSER	(1<<31)
+#define SB_SUBMOUNT     BIT(26)
+#define SB_FORCE        BIT(27)
+#define SB_NOSEC        BIT(28)
+#define SB_BORN         BIT(29)
+#define SB_ACTIVE       BIT(30)
+#define SB_NOUSER       BIT(31)
 
 /* These flags relate to encoding and casefolding */
 #define SB_ENC_STRICT_MODE_FL	(1 << 0)
@@ -1443,6 +1475,8 @@
 #define SB_I_UNTRUSTED_MOUNTER		0x00000040
 
 #define SB_I_SKIP_SYNC	0x00000100	/* Skip superblock at global sync */
+#define SB_I_PERSB_BDI	0x00000200	/* has a per-sb bdi */
+#define SB_I_TS_EXPIRY_WARNED 0x00000400 /* warned about timestamp range expiry */
 
 /* Possible states of 'frozen' field */
 enum {
@@ -1486,7 +1520,7 @@
 	const struct xattr_handler **s_xattr;
 #ifdef CONFIG_FS_ENCRYPTION
 	const struct fscrypt_operations	*s_cop;
-	struct key		*s_master_keys; /* master crypto keys in use */
+	struct fscrypt_keyring	*s_master_keys; /* master crypto keys in use */
 #endif
 #ifdef CONFIG_FS_VERITY
 	const struct fsverity_operations *s_vop;
@@ -1601,6 +1635,11 @@
 	struct list_head	s_inodes_wb;	/* writeback inodes */
 } __randomize_layout;
 
+static inline struct user_namespace *i_user_ns(const struct inode *inode)
+{
+	return inode->i_sb->s_user_ns;
+}
+
 /* Helper functions so that in most cases filesystems will
  * not need to deal directly with kuid_t and kgid_t and can
  * instead deal with the raw numeric values that are stored
@@ -1608,50 +1647,22 @@
  */
 static inline uid_t i_uid_read(const struct inode *inode)
 {
-	return from_kuid(inode->i_sb->s_user_ns, inode->i_uid);
+	return from_kuid(i_user_ns(inode), inode->i_uid);
 }
 
 static inline gid_t i_gid_read(const struct inode *inode)
 {
-	return from_kgid(inode->i_sb->s_user_ns, inode->i_gid);
+	return from_kgid(i_user_ns(inode), inode->i_gid);
 }
 
 static inline void i_uid_write(struct inode *inode, uid_t uid)
 {
-	inode->i_uid = make_kuid(inode->i_sb->s_user_ns, uid);
+	inode->i_uid = make_kuid(i_user_ns(inode), uid);
 }
 
 static inline void i_gid_write(struct inode *inode, gid_t gid)
 {
-	inode->i_gid = make_kgid(inode->i_sb->s_user_ns, gid);
-}
-
-/**
- * kuid_into_mnt - map a kuid down into a mnt_userns
- * @mnt_userns: user namespace of the relevant mount
- * @kuid: kuid to be mapped
- *
- * Return: @kuid mapped according to @mnt_userns.
- * If @kuid has no mapping INVALID_UID is returned.
- */
-static inline kuid_t kuid_into_mnt(struct user_namespace *mnt_userns,
-				   kuid_t kuid)
-{
-	return make_kuid(mnt_userns, __kuid_val(kuid));
-}
-
-/**
- * kgid_into_mnt - map a kgid down into a mnt_userns
- * @mnt_userns: user namespace of the relevant mount
- * @kgid: kgid to be mapped
- *
- * Return: @kgid mapped according to @mnt_userns.
- * If @kgid has no mapping INVALID_GID is returned.
- */
-static inline kgid_t kgid_into_mnt(struct user_namespace *mnt_userns,
-				   kgid_t kgid)
-{
-	return make_kgid(mnt_userns, __kgid_val(kgid));
+	inode->i_gid = make_kgid(i_user_ns(inode), gid);
 }
 
 /**
@@ -1665,7 +1676,7 @@
 static inline kuid_t i_uid_into_mnt(struct user_namespace *mnt_userns,
 				    const struct inode *inode)
 {
-	return kuid_into_mnt(mnt_userns, inode->i_uid);
+	return mapped_kuid_fs(mnt_userns, i_user_ns(inode), inode->i_uid);
 }
 
 /**
@@ -1679,69 +1690,7 @@
 static inline kgid_t i_gid_into_mnt(struct user_namespace *mnt_userns,
 				    const struct inode *inode)
 {
-	return kgid_into_mnt(mnt_userns, inode->i_gid);
-}
-
-/**
- * kuid_from_mnt - map a kuid up into a mnt_userns
- * @mnt_userns: user namespace of the relevant mount
- * @kuid: kuid to be mapped
- *
- * Return: @kuid mapped up according to @mnt_userns.
- * If @kuid has no mapping INVALID_UID is returned.
- */
-static inline kuid_t kuid_from_mnt(struct user_namespace *mnt_userns,
-				   kuid_t kuid)
-{
-	return KUIDT_INIT(from_kuid(mnt_userns, kuid));
-}
-
-/**
- * kgid_from_mnt - map a kgid up into a mnt_userns
- * @mnt_userns: user namespace of the relevant mount
- * @kgid: kgid to be mapped
- *
- * Return: @kgid mapped up according to @mnt_userns.
- * If @kgid has no mapping INVALID_GID is returned.
- */
-static inline kgid_t kgid_from_mnt(struct user_namespace *mnt_userns,
-				   kgid_t kgid)
-{
-	return KGIDT_INIT(from_kgid(mnt_userns, kgid));
-}
-
-/**
- * mapped_fsuid - return caller's fsuid mapped up into a mnt_userns
- * @mnt_userns: user namespace of the relevant mount
- *
- * Use this helper to initialize a new vfs or filesystem object based on
- * the caller's fsuid. A common example is initializing the i_uid field of
- * a newly allocated inode triggered by a creation event such as mkdir or
- * O_CREAT. Other examples include the allocation of quotas for a specific
- * user.
- *
- * Return: the caller's current fsuid mapped up according to @mnt_userns.
- */
-static inline kuid_t mapped_fsuid(struct user_namespace *mnt_userns)
-{
-	return kuid_from_mnt(mnt_userns, current_fsuid());
-}
-
-/**
- * mapped_fsgid - return caller's fsgid mapped up into a mnt_userns
- * @mnt_userns: user namespace of the relevant mount
- *
- * Use this helper to initialize a new vfs or filesystem object based on
- * the caller's fsgid. A common example is initializing the i_gid field of
- * a newly allocated inode triggered by a creation event such as mkdir or
- * O_CREAT. Other examples include the allocation of quotas for a specific
- * user.
- *
- * Return: the caller's current fsgid mapped up according to @mnt_userns.
- */
-static inline kgid_t mapped_fsgid(struct user_namespace *mnt_userns)
-{
-	return kgid_from_mnt(mnt_userns, current_fsgid());
+	return mapped_kgid_fs(mnt_userns, i_user_ns(inode), inode->i_gid);
 }
 
 /**
@@ -1755,7 +1704,7 @@
 static inline void inode_fsuid_set(struct inode *inode,
 				   struct user_namespace *mnt_userns)
 {
-	inode->i_uid = mapped_fsuid(mnt_userns);
+	inode->i_uid = mapped_fsuid(mnt_userns, i_user_ns(inode));
 }
 
 /**
@@ -1769,7 +1718,7 @@
 static inline void inode_fsgid_set(struct inode *inode,
 				   struct user_namespace *mnt_userns)
 {
-	inode->i_gid = mapped_fsgid(mnt_userns);
+	inode->i_gid = mapped_fsgid(mnt_userns, i_user_ns(inode));
 }
 
 /**
@@ -1786,13 +1735,64 @@
 static inline bool fsuidgid_has_mapping(struct super_block *sb,
 					struct user_namespace *mnt_userns)
 {
-	struct user_namespace *s_user_ns = sb->s_user_ns;
+	struct user_namespace *fs_userns = sb->s_user_ns;
+	kuid_t kuid;
+	kgid_t kgid;
+
+	kuid = mapped_fsuid(mnt_userns, fs_userns);
+	if (!uid_valid(kuid))
+		return false;
+	kgid = mapped_fsgid(mnt_userns, fs_userns);
+	if (!gid_valid(kgid))
+		return false;
+	return kuid_has_mapping(fs_userns, kuid) &&
+	       kgid_has_mapping(fs_userns, kgid);
+}
+
+struct timespec64 current_time(struct inode *inode);
+struct timespec64 inode_set_ctime_current(struct inode *inode);
 
-	return kuid_has_mapping(s_user_ns, mapped_fsuid(mnt_userns)) &&
-	       kgid_has_mapping(s_user_ns, mapped_fsgid(mnt_userns));
+/**
+ * inode_get_ctime - fetch the current ctime from the inode
+ * @inode: inode from which to fetch ctime
+ *
+ * Grab the current ctime from the inode and return it.
+ */
+static inline struct timespec64 inode_get_ctime(const struct inode *inode)
+{
+	return inode->i_ctime;
+}
+
+/**
+ * inode_set_ctime_to_ts - set the ctime in the inode
+ * @inode: inode in which to set the ctime
+ * @ts: value to set in the ctime field
+ *
+ * Set the ctime in @inode to @ts
+ */
+static inline struct timespec64 inode_set_ctime_to_ts(struct inode *inode,
+						      struct timespec64 ts)
+{
+	inode->i_ctime = ts;
+	return ts;
 }
 
-extern struct timespec64 current_time(struct inode *inode);
+/**
+ * inode_set_ctime - set the ctime in the inode
+ * @inode: inode in which to set the ctime
+ * @sec: tv_sec value to set
+ * @nsec: tv_nsec value to set
+ *
+ * Set the ctime in @inode to { @sec, @nsec }
+ */
+static inline struct timespec64 inode_set_ctime(struct inode *inode,
+						time64_t sec, long nsec)
+{
+	struct timespec64 ts = { .tv_sec  = sec,
+				 .tv_nsec = nsec };
+
+	return inode_set_ctime_to_ts(inode, ts);
+}
 
 /*
  * Snapshotting support.
@@ -2011,6 +2011,8 @@
 void inode_init_owner(struct user_namespace *mnt_userns, struct inode *inode,
 		      const struct inode *dir, umode_t mode);
 extern bool may_open_dev(const struct path *path);
+umode_t mode_strip_sgid(struct user_namespace *mnt_userns,
+			const struct inode *dir, umode_t mode);
 
 /*
  * This is the "filldir" function type, used by readdir() to let
@@ -2066,6 +2068,14 @@
  */
 #define REMAP_FILE_ADVISORY		(REMAP_FILE_CAN_SHORTEN)
 
+/*
+ * These flags control the behavior of vfs_copy_file_range().
+ * They are not available to the user via syscall.
+ *
+ * COPY_FILE_SPLICE: call splice direct instead of fs clone/copy ops
+ */
+#define COPY_FILE_SPLICE		(1 << 0)
+
 struct iov_iter;
 
 struct file_operations {
@@ -2092,6 +2102,7 @@
 	ssize_t (*sendpage) (struct file *, struct page *, int, size_t, loff_t *, int);
 	unsigned long (*get_unmapped_area)(struct file *, unsigned long, unsigned long, unsigned long, unsigned long);
 	int (*check_flags)(int);
+	int (*setfl)(struct file *, unsigned long);
 	int (*flock) (struct file *, int, struct file_lock *);
 	ssize_t (*splice_write)(struct pipe_inode_info *, struct file *, loff_t *, size_t, unsigned int);
 	ssize_t (*splice_read)(struct file *, loff_t *, struct pipe_inode_info *, size_t, unsigned int);
@@ -2224,6 +2235,10 @@
 				  struct shrink_control *);
 	long (*free_cached_objects)(struct super_block *,
 				    struct shrink_control *);
+#if IS_ENABLED(CONFIG_BLK_DEV_LOOP) || IS_ENABLED(CONFIG_BLK_DEV_LOOP_MODULE)
+	/* and aufs */
+	struct file *(*real_loop)(struct file *);
+#endif
 };
 
 /*
@@ -2364,13 +2379,14 @@
  *			don't have to write inode on fdatasync() when only
  *			e.g. the timestamps have changed.
  * I_DIRTY_PAGES	Inode has dirty pages.  Inode itself may be clean.
- * I_DIRTY_TIME		The inode itself only has dirty timestamps, and the
+ * I_DIRTY_TIME		The inode itself has dirty timestamps, and the
  *			lazytime mount option is enabled.  We keep track of this
  *			separately from I_DIRTY_SYNC in order to implement
  *			lazytime.  This gets cleared if I_DIRTY_INODE
- *			(I_DIRTY_SYNC and/or I_DIRTY_DATASYNC) gets set.  I.e.
- *			either I_DIRTY_TIME *or* I_DIRTY_INODE can be set in
- *			i_state, but not both.  I_DIRTY_PAGES may still be set.
+ *			(I_DIRTY_SYNC and/or I_DIRTY_DATASYNC) gets set. But
+ *			I_DIRTY_TIME can still be set if I_DIRTY_SYNC is already
+ *			in place because writeback might already be in progress
+ *			and we don't want to lose the time update
  * I_NEW		Serves as both a mutex and completion notification.
  *			New inodes set I_NEW.  If two processes both create
  *			the same inode, one of them will release its inode and
@@ -2419,6 +2435,9 @@
  *			Used to detect that mark_inode_dirty() should not move
  * 			inode between dirty lists.
  *
+ * I_LRU_ISOLATING	Inode is pinned being isolated from LRU without holding
+ *			i_count.
+ *
  * Q: What is the difference between I_WILL_FREE and I_FREEING?
  */
 #define I_DIRTY_SYNC		(1 << 0)
@@ -2441,6 +2460,8 @@
 #define I_CREATING		(1 << 15)
 #define I_DONTCACHE		(1 << 16)
 #define I_SYNC_QUEUED		(1 << 17)
+#define __I_LRU_ISOLATING	19
+#define I_LRU_ISOLATING		(1 << __I_LRU_ISOLATING)
 
 #define I_DIRTY_INODE (I_DIRTY_SYNC | I_DIRTY_DATASYNC)
 #define I_DIRTY (I_DIRTY_INODE | I_DIRTY_PAGES)
@@ -2498,6 +2519,8 @@
 
 extern bool atime_needs_update(const struct path *, struct inode *);
 extern void touch_atime(const struct path *);
+int inode_update_time(struct inode *inode, struct timespec64 *time, int flags);
+
 static inline void file_accessed(struct file *file)
 {
 	if (!(file->f_flags & O_NOATIME))
@@ -2613,6 +2636,7 @@
 extern void ihold(struct inode * inode);
 extern void iput(struct inode *);
 extern int generic_update_time(struct inode *, struct timespec64 *, int);
+extern int update_time(struct inode *, struct timespec64 *, int);
 
 /* /sys/fs */
 extern struct kobject *fs_kobj;
@@ -2724,6 +2748,21 @@
 {
 	return mnt_user_ns(file->f_path.mnt);
 }
+
+/**
+ * is_idmapped_mnt - check whether a mount is mapped
+ * @mnt: the mount to check
+ *
+ * If @mnt has an idmapping attached different from the
+ * filesystem's idmapping then @mnt is mapped.
+ *
+ * Return: true if mount is mapped, false if not.
+ */
+static inline bool is_idmapped_mnt(const struct vfsmount *mnt)
+{
+	return mnt_user_ns(mnt) != mnt->mnt_sb->s_user_ns;
+}
+
 extern long vfs_truncate(const struct path *, loff_t);
 int do_truncate(struct user_namespace *, struct dentry *, loff_t start,
 		unsigned int time_attrs, struct file *filp);
@@ -2742,6 +2781,8 @@
 			      name, flags, mode);
 }
 extern struct file * dentry_open(const struct path *, int, const struct cred *);
+extern struct file *dentry_create(const struct path *path, int flags,
+				  umode_t mode, const struct cred *cred);
 extern struct file * open_with_fake_path(const struct path *, int,
 					 struct inode*, const struct cred *);
 static inline struct file *file_clone_open(struct file *file)
@@ -2776,6 +2817,7 @@
 }
 
 void emergency_thaw_all(void);
+extern int __sync_filesystem(struct super_block *, int);
 extern int sync_filesystem(struct super_block *);
 extern const struct file_operations def_blk_fops;
 extern const struct file_operations def_chr_fops;
@@ -3022,6 +3064,42 @@
 	__sb_end_write(file_inode(file)->i_sb, SB_FREEZE_WRITE);
 }
 
+/**
+ * kiocb_start_write - get write access to a superblock for async file io
+ * @iocb: the io context we want to submit the write with
+ *
+ * This is a variant of sb_start_write() for async io submission.
+ * Should be matched with a call to kiocb_end_write().
+ */
+static inline void kiocb_start_write(struct kiocb *iocb)
+{
+	struct inode *inode = file_inode(iocb->ki_filp);
+
+	sb_start_write(inode->i_sb);
+	/*
+	 * Fool lockdep by telling it the lock got released so that it
+	 * doesn't complain about the held lock when we return to userspace.
+	 */
+	__sb_writers_release(inode->i_sb, SB_FREEZE_WRITE);
+}
+
+/**
+ * kiocb_end_write - drop write access to a superblock after async file io
+ * @iocb: the io context we sumbitted the write with
+ *
+ * Should be matched with a call to kiocb_start_write().
+ */
+static inline void kiocb_end_write(struct kiocb *iocb)
+{
+	struct inode *inode = file_inode(iocb->ki_filp);
+
+	/*
+	 * Tell lockdep we inherited freeze protection from submission thread.
+	 */
+	__sb_writers_acquired(inode->i_sb, SB_FREEZE_WRITE);
+	sb_end_write(inode->i_sb);
+}
+
 /*
  * This is used for regular files where some users -- especially the
  * currently executed binary in a process, previously handled via
@@ -3175,8 +3253,10 @@
 extern struct inode *new_inode_pseudo(struct super_block *sb);
 extern struct inode *new_inode(struct super_block *sb);
 extern void free_inode_nonrcu(struct inode *inode);
-extern int should_remove_suid(struct dentry *);
+extern int setattr_should_drop_suidgid(struct user_namespace *, struct inode *);
 extern int file_remove_privs(struct file *);
+int setattr_should_drop_sgid(struct user_namespace *mnt_userns,
+			     const struct inode *inode);
 
 extern void __insert_inode_hash(struct inode *, unsigned long hashval);
 static inline void insert_inode_hash(struct inode *inode)
@@ -3315,6 +3395,8 @@
 
 extern int readlink_copy(char __user *, int, const char *);
 extern int page_readlink(struct dentry *, char __user *, int);
+extern const char *page_get_link_raw(struct dentry *, struct inode *,
+				     struct delayed_call *);
 extern const char *page_get_link(struct dentry *, struct inode *,
 				 struct delayed_call *);
 extern void page_put_link(void *);
@@ -3557,7 +3639,7 @@
  * All attributes contain a text representation of a numeric value
  * that are accessed with the get() and set() functions.
  */
-#define DEFINE_SIMPLE_ATTRIBUTE(__fops, __get, __set, __fmt)		\
+#define DEFINE_SIMPLE_ATTRIBUTE_XSIGNED(__fops, __get, __set, __fmt, __is_signed)	\
 static int __fops ## _open(struct inode *inode, struct file *file)	\
 {									\
 	__simple_attr_check_format(__fmt, 0ull);			\
@@ -3568,10 +3650,16 @@
 	.open	 = __fops ## _open,					\
 	.release = simple_attr_release,					\
 	.read	 = simple_attr_read,					\
-	.write	 = simple_attr_write,					\
+	.write	 = (__is_signed) ? simple_attr_write_signed : simple_attr_write,	\
 	.llseek	 = generic_file_llseek,					\
 }
 
+#define DEFINE_SIMPLE_ATTRIBUTE(__fops, __get, __set, __fmt)		\
+	DEFINE_SIMPLE_ATTRIBUTE_XSIGNED(__fops, __get, __set, __fmt, false)
+
+#define DEFINE_SIMPLE_ATTRIBUTE_SIGNED(__fops, __get, __set, __fmt)	\
+	DEFINE_SIMPLE_ATTRIBUTE_XSIGNED(__fops, __get, __set, __fmt, true)
+
 static inline __printf(1, 2)
 void __simple_attr_check_format(const char *fmt, ...)
 {
@@ -3586,14 +3674,12 @@
 			 size_t len, loff_t *ppos);
 ssize_t simple_attr_write(struct file *file, const char __user *buf,
 			  size_t len, loff_t *ppos);
+ssize_t simple_attr_write_signed(struct file *file, const char __user *buf,
+				 size_t len, loff_t *ppos);
 
 struct ctl_table;
-int proc_nr_files(struct ctl_table *table, int write,
-		  void *buffer, size_t *lenp, loff_t *ppos);
 int proc_nr_dentry(struct ctl_table *table, int write,
 		  void *buffer, size_t *lenp, loff_t *ppos);
-int proc_nr_inodes(struct ctl_table *table, int write,
-		   void *buffer, size_t *lenp, loff_t *ppos);
 int __init list_bdev_fs_names(char *buf, size_t size);
 
 #define __FMODE_EXEC		((__force int) FMODE_EXEC)
@@ -3605,7 +3691,7 @@
 
 static inline bool is_sxid(umode_t mode)
 {
-	return (mode & S_ISUID) || ((mode & S_ISGID) && (mode & S_IXGRP));
+	return mode & (S_ISUID | S_ISGID);
 }
 
 static inline int check_sticky(struct user_namespace *mnt_userns,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fs_context.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fs_context.h
@@ -142,6 +142,8 @@
 extern int vfs_parse_fs_param_source(struct fs_context *fc,
 				     struct fs_parameter *param);
 extern void fc_drop_locked(struct fs_context *fc);
+int reconfigure_single(struct super_block *s,
+		       int flags, void *data);
 
 /*
  * sget() wrappers to be called from the ->get_tree() op.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fscache.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fscache.h
@@ -167,7 +167,7 @@
 
 static inline bool fscache_cookie_enabled(struct fscache_cookie *cookie)
 {
-	return test_bit(FSCACHE_COOKIE_ENABLED, &cookie->flags);
+	return fscache_cookie_valid(cookie) && test_bit(FSCACHE_COOKIE_ENABLED, &cookie->flags);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fscrypt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fscrypt.h
@@ -294,7 +294,7 @@
 }
 
 /* keyring.c */
-void fscrypt_sb_free(struct super_block *sb);
+void fscrypt_destroy_keyring(struct super_block *sb);
 int fscrypt_ioctl_add_key(struct file *filp, void __user *arg);
 int fscrypt_ioctl_remove_key(struct file *filp, void __user *arg);
 int fscrypt_ioctl_remove_key_all_users(struct file *filp, void __user *arg);
@@ -482,7 +482,7 @@
 }
 
 /* keyring.c */
-static inline void fscrypt_sb_free(struct super_block *sb)
+static inline void fscrypt_destroy_keyring(struct super_block *sb)
 {
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fsl/enetc_mdio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fsl/enetc_mdio.h
@@ -48,7 +48,8 @@
 static inline int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum,
 				   u16 value)
 { return -EINVAL; }
-struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
+static inline struct enetc_hw *enetc_hw_alloc(struct device *dev,
+					      void __iomem *port_regs)
 { return ERR_PTR(-EINVAL); }
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fsnotify.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fsnotify.h
@@ -26,20 +26,20 @@
  * FS_EVENT_ON_CHILD mask on the parent inode and will not be reported if only
  * the child is interested and not the parent.
  */
-static inline void fsnotify_name(struct inode *dir, __u32 mask,
-				 struct inode *child,
-				 const struct qstr *name, u32 cookie)
+static inline int fsnotify_name(__u32 mask, const void *data, int data_type,
+				struct inode *dir, const struct qstr *name,
+				u32 cookie)
 {
 	if (atomic_long_read(&dir->i_sb->s_fsnotify_connectors) == 0)
-		return;
+		return 0;
 
-	fsnotify(mask, child, FSNOTIFY_EVENT_INODE, dir, name, NULL, cookie);
+	return fsnotify(mask, data, data_type, dir, name, NULL, cookie);
 }
 
 static inline void fsnotify_dirent(struct inode *dir, struct dentry *dentry,
 				   __u32 mask)
 {
-	fsnotify_name(dir, mask, d_inode(dentry), &dentry->d_name, 0);
+	fsnotify_name(mask, dentry, FSNOTIFY_EVENT_DENTRY, dir, &dentry->d_name, 0);
 }
 
 static inline void fsnotify_inode(struct inode *inode, __u32 mask)
@@ -86,14 +86,20 @@
  */
 static inline void fsnotify_dentry(struct dentry *dentry, __u32 mask)
 {
-	fsnotify_parent(dentry, mask, d_inode(dentry), FSNOTIFY_EVENT_INODE);
+	fsnotify_parent(dentry, mask, dentry, FSNOTIFY_EVENT_DENTRY);
 }
 
 static inline int fsnotify_file(struct file *file, __u32 mask)
 {
 	const struct path *path = &file->f_path;
 
-	if (file->f_mode & FMODE_NONOTIFY)
+	/*
+	 * FMODE_NONOTIFY are fds generated by fanotify itself which should not
+	 * generate new events. We also don't want to generate events for
+	 * FMODE_PATH fds (involves open & close events) as they are just
+	 * handle creation / destruction events and not "real" file events.
+	 */
+	if (file->f_mode & (FMODE_NONOTIFY | FMODE_PATH))
 		return 0;
 
 	return fsnotify_parent(path->dentry, mask, path, FSNOTIFY_EVENT_PATH);
@@ -144,18 +150,23 @@
 	u32 fs_cookie = fsnotify_get_cookie();
 	__u32 old_dir_mask = FS_MOVED_FROM;
 	__u32 new_dir_mask = FS_MOVED_TO;
+	__u32 rename_mask = FS_RENAME;
 	const struct qstr *new_name = &moved->d_name;
 
-	if (old_dir == new_dir)
-		old_dir_mask |= FS_DN_RENAME;
-
 	if (isdir) {
 		old_dir_mask |= FS_ISDIR;
 		new_dir_mask |= FS_ISDIR;
+		rename_mask |= FS_ISDIR;
 	}
 
-	fsnotify_name(old_dir, old_dir_mask, source, old_name, fs_cookie);
-	fsnotify_name(new_dir, new_dir_mask, source, new_name, fs_cookie);
+	/* Event with information about both old and new parent+name */
+	fsnotify_name(rename_mask, moved, FSNOTIFY_EVENT_DENTRY,
+		      old_dir, old_name, 0);
+
+	fsnotify_name(old_dir_mask, source, FSNOTIFY_EVENT_INODE,
+		      old_dir, old_name, fs_cookie);
+	fsnotify_name(new_dir_mask, source, FSNOTIFY_EVENT_INODE,
+		      new_dir, new_name, fs_cookie);
 
 	if (target)
 		fsnotify_link_count(target);
@@ -190,16 +201,22 @@
 
 /*
  * fsnotify_create - 'name' was linked in
+ *
+ * Caller must make sure that dentry->d_name is stable.
+ * Note: some filesystems (e.g. kernfs) leave @dentry negative and instantiate
+ * ->d_inode later
  */
-static inline void fsnotify_create(struct inode *inode, struct dentry *dentry)
+static inline void fsnotify_create(struct inode *dir, struct dentry *dentry)
 {
-	audit_inode_child(inode, dentry, AUDIT_TYPE_CHILD_CREATE);
+	audit_inode_child(dir, dentry, AUDIT_TYPE_CHILD_CREATE);
 
-	fsnotify_dirent(inode, dentry, FS_CREATE);
+	fsnotify_dirent(dir, dentry, FS_CREATE);
 }
 
 /*
  * fsnotify_link - new hardlink in 'inode' directory
+ *
+ * Caller must make sure that new_dentry->d_name is stable.
  * Note: We have to pass also the linked inode ptr as some filesystems leave
  *   new_dentry->d_inode NULL and instantiate inode pointer later
  */
@@ -209,7 +226,45 @@
 	fsnotify_link_count(inode);
 	audit_inode_child(dir, new_dentry, AUDIT_TYPE_CHILD_CREATE);
 
-	fsnotify_name(dir, FS_CREATE, inode, &new_dentry->d_name, 0);
+	fsnotify_name(FS_CREATE, inode, FSNOTIFY_EVENT_INODE,
+		      dir, &new_dentry->d_name, 0);
+}
+
+/*
+ * fsnotify_delete - @dentry was unlinked and unhashed
+ *
+ * Caller must make sure that dentry->d_name is stable.
+ *
+ * Note: unlike fsnotify_unlink(), we have to pass also the unlinked inode
+ * as this may be called after d_delete() and old_dentry may be negative.
+ */
+static inline void fsnotify_delete(struct inode *dir, struct inode *inode,
+				   struct dentry *dentry)
+{
+	__u32 mask = FS_DELETE;
+
+	if (S_ISDIR(inode->i_mode))
+		mask |= FS_ISDIR;
+
+	fsnotify_name(mask, inode, FSNOTIFY_EVENT_INODE, dir, &dentry->d_name,
+		      0);
+}
+
+/**
+ * d_delete_notify - delete a dentry and call fsnotify_delete()
+ * @dentry: The dentry to delete
+ *
+ * This helper is used to guaranty that the unlinked inode cannot be found
+ * by lookup of this name after fsnotify_delete() event has been delivered.
+ */
+static inline void d_delete_notify(struct inode *dir, struct dentry *dentry)
+{
+	struct inode *inode = d_inode(dentry);
+
+	ihold(inode);
+	d_delete(dentry);
+	fsnotify_delete(dir, inode, dentry);
+	iput(inode);
 }
 
 /*
@@ -219,20 +274,24 @@
  */
 static inline void fsnotify_unlink(struct inode *dir, struct dentry *dentry)
 {
-	/* Expected to be called before d_delete() */
-	WARN_ON_ONCE(d_is_negative(dentry));
+	if (WARN_ON_ONCE(d_is_negative(dentry)))
+		return;
 
-	fsnotify_dirent(dir, dentry, FS_DELETE);
+	fsnotify_delete(dir, d_inode(dentry), dentry);
 }
 
 /*
  * fsnotify_mkdir - directory 'name' was created
+ *
+ * Caller must make sure that dentry->d_name is stable.
+ * Note: some filesystems (e.g. kernfs) leave @dentry negative and instantiate
+ * ->d_inode later
  */
-static inline void fsnotify_mkdir(struct inode *inode, struct dentry *dentry)
+static inline void fsnotify_mkdir(struct inode *dir, struct dentry *dentry)
 {
-	audit_inode_child(inode, dentry, AUDIT_TYPE_CHILD_CREATE);
+	audit_inode_child(dir, dentry, AUDIT_TYPE_CHILD_CREATE);
 
-	fsnotify_dirent(inode, dentry, FS_CREATE | FS_ISDIR);
+	fsnotify_dirent(dir, dentry, FS_CREATE | FS_ISDIR);
 }
 
 /*
@@ -242,10 +301,10 @@
  */
 static inline void fsnotify_rmdir(struct inode *dir, struct dentry *dentry)
 {
-	/* Expected to be called before d_delete() */
-	WARN_ON_ONCE(d_is_negative(dentry));
+	if (WARN_ON_ONCE(d_is_negative(dentry)))
+		return;
 
-	fsnotify_dirent(dir, dentry, FS_DELETE | FS_ISDIR);
+	fsnotify_delete(dir, d_inode(dentry), dentry);
 }
 
 /*
@@ -326,4 +385,17 @@
 		fsnotify_dentry(dentry, mask);
 }
 
+static inline int fsnotify_sb_error(struct super_block *sb, struct inode *inode,
+				    int error)
+{
+	struct fs_error_report report = {
+		.error = error,
+		.inode = inode,
+		.sb = sb,
+	};
+
+	return fsnotify(FS_ERROR, &report, FSNOTIFY_EVENT_ERROR,
+			NULL, NULL, NULL, 0);
+}
+
 #endif	/* _LINUX_FS_NOTIFY_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fsnotify_backend.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fsnotify_backend.h
@@ -19,6 +19,8 @@
 #include <linux/atomic.h>
 #include <linux/user_namespace.h>
 #include <linux/refcount.h>
+#include <linux/mempool.h>
+#include <linux/sched/mm.h>
 
 /*
  * IN_* from inotfy.h lines up EXACTLY with FS_*, this is so we can easily
@@ -42,13 +44,18 @@
 
 #define FS_UNMOUNT		0x00002000	/* inode on umount fs */
 #define FS_Q_OVERFLOW		0x00004000	/* Event queued overflowed */
+#define FS_ERROR		0x00008000	/* Filesystem Error (fanotify) */
+
+/*
+ * FS_IN_IGNORED overloads FS_ERROR.  It is only used internally by inotify
+ * which does not support FS_ERROR.
+ */
 #define FS_IN_IGNORED		0x00008000	/* last inotify event here */
 
 #define FS_OPEN_PERM		0x00010000	/* open event in an permission hook */
 #define FS_ACCESS_PERM		0x00020000	/* access event in a permissions hook */
 #define FS_OPEN_EXEC_PERM	0x00040000	/* open/exec event in a permission hook */
 
-#define FS_EXCL_UNLINK		0x04000000	/* do not send events if object is unlinked */
 /*
  * Set on inode mark that cares about things that happen to its children.
  * Always set for dnotify and inotify.
@@ -56,10 +63,9 @@
  */
 #define FS_EVENT_ON_CHILD	0x08000000
 
-#define FS_DN_RENAME		0x10000000	/* file renamed */
+#define FS_RENAME		0x10000000	/* File was renamed */
 #define FS_DN_MULTISHOT		0x20000000	/* dnotify multishot */
 #define FS_ISDIR		0x40000000	/* event occurred against dir */
-#define FS_IN_ONESHOT		0x80000000	/* only send event once */
 
 #define FS_MOVE			(FS_MOVED_FROM | FS_MOVED_TO)
 
@@ -69,7 +75,7 @@
  * The watching parent may get an FS_ATTRIB|FS_EVENT_ON_CHILD event
  * when a directory entry inside a child subdir changes.
  */
-#define ALL_FSNOTIFY_DIRENT_EVENTS	(FS_CREATE | FS_DELETE | FS_MOVE)
+#define ALL_FSNOTIFY_DIRENT_EVENTS (FS_CREATE | FS_DELETE | FS_MOVE | FS_RENAME)
 
 #define ALL_FSNOTIFY_PERM_EVENTS (FS_OPEN_PERM | FS_ACCESS_PERM | \
 				  FS_OPEN_EXEC_PERM)
@@ -94,12 +100,12 @@
 /* Events that can be reported to backends */
 #define ALL_FSNOTIFY_EVENTS (ALL_FSNOTIFY_DIRENT_EVENTS | \
 			     FS_EVENTS_POSS_ON_CHILD | \
-			     FS_DELETE_SELF | FS_MOVE_SELF | FS_DN_RENAME | \
-			     FS_UNMOUNT | FS_Q_OVERFLOW | FS_IN_IGNORED)
+			     FS_DELETE_SELF | FS_MOVE_SELF | \
+			     FS_UNMOUNT | FS_Q_OVERFLOW | FS_IN_IGNORED | \
+			     FS_ERROR)
 
 /* Extra flags that may be reported with event or control handling of events */
-#define ALL_FSNOTIFY_FLAGS  (FS_EXCL_UNLINK | FS_ISDIR | FS_IN_ONESHOT | \
-			     FS_DN_MULTISHOT | FS_EVENT_ON_CHILD)
+#define ALL_FSNOTIFY_FLAGS  (FS_ISDIR | FS_EVENT_ON_CHILD | FS_DN_MULTISHOT)
 
 #define ALL_FSNOTIFY_BITS   (ALL_FSNOTIFY_EVENTS | ALL_FSNOTIFY_FLAGS)
 
@@ -136,6 +142,7 @@
  * @dir:	optional directory associated with event -
  *		if @file_name is not NULL, this is the directory that
  *		@file_name is relative to.
+ *		Either @inode or @dir must be non-NULL.
  * @file_name:	optional file name associated with event
  * @cookie:	inotify rename cookie
  *
@@ -155,7 +162,7 @@
 			    const struct qstr *file_name, u32 cookie);
 	void (*free_group_priv)(struct fsnotify_group *group);
 	void (*freeing_mark)(struct fsnotify_mark *mark, struct fsnotify_group *group);
-	void (*free_event)(struct fsnotify_event *event);
+	void (*free_event)(struct fsnotify_group *group, struct fsnotify_event *event);
 	/* called on final put+free to free memory */
 	void (*free_mark)(struct fsnotify_mark *mark);
 };
@@ -204,6 +211,12 @@
 	unsigned int priority;
 	bool shutdown;		/* group is being shut down, don't queue more events */
 
+#define FSNOTIFY_GROUP_USER	0x01 /* user allocated group */
+#define FSNOTIFY_GROUP_DUPS	0x02 /* allow multiple marks per object */
+#define FSNOTIFY_GROUP_NOFS	0x04 /* group lock is not direct reclaim safe */
+	int flags;
+	unsigned int owner_flags;	/* stored flags of mark_mutex owner */
+
 	/* stores all fastpath marks assoc with this group so they can be cleaned on unregister */
 	struct mutex mark_mutex;	/* protect marks_list */
 	atomic_t user_waits;		/* Number of tasks waiting for user
@@ -238,16 +251,50 @@
 			int flags;           /* flags from fanotify_init() */
 			int f_flags; /* event_f_flags from fanotify_init() */
 			struct ucounts *ucounts;
+			mempool_t error_events_pool;
 		} fanotify_data;
 #endif /* CONFIG_FANOTIFY */
 	};
 };
 
+/*
+ * These helpers are used to prevent deadlock when reclaiming inodes with
+ * evictable marks of the same group that is allocating a new mark.
+ */
+static inline void fsnotify_group_lock(struct fsnotify_group *group)
+{
+	mutex_lock(&group->mark_mutex);
+	if (group->flags & FSNOTIFY_GROUP_NOFS)
+		group->owner_flags = memalloc_nofs_save();
+}
+
+static inline void fsnotify_group_unlock(struct fsnotify_group *group)
+{
+	if (group->flags & FSNOTIFY_GROUP_NOFS)
+		memalloc_nofs_restore(group->owner_flags);
+	mutex_unlock(&group->mark_mutex);
+}
+
+static inline void fsnotify_group_assert_locked(struct fsnotify_group *group)
+{
+	WARN_ON_ONCE(!mutex_is_locked(&group->mark_mutex));
+	if (group->flags & FSNOTIFY_GROUP_NOFS)
+		WARN_ON_ONCE(!(current->flags & PF_MEMALLOC_NOFS));
+}
+
 /* When calling fsnotify tell it if the data is a path or inode */
 enum fsnotify_data_type {
 	FSNOTIFY_EVENT_NONE,
 	FSNOTIFY_EVENT_PATH,
 	FSNOTIFY_EVENT_INODE,
+	FSNOTIFY_EVENT_DENTRY,
+	FSNOTIFY_EVENT_ERROR,
+};
+
+struct fs_error_report {
+	int error;
+	struct inode *inode;
+	struct super_block *sb;
 };
 
 static inline struct inode *fsnotify_data_inode(const void *data, int data_type)
@@ -255,8 +302,25 @@
 	switch (data_type) {
 	case FSNOTIFY_EVENT_INODE:
 		return (struct inode *)data;
+	case FSNOTIFY_EVENT_DENTRY:
+		return d_inode(data);
 	case FSNOTIFY_EVENT_PATH:
 		return d_inode(((const struct path *)data)->dentry);
+	case FSNOTIFY_EVENT_ERROR:
+		return ((struct fs_error_report *)data)->inode;
+	default:
+		return NULL;
+	}
+}
+
+static inline struct dentry *fsnotify_data_dentry(const void *data, int data_type)
+{
+	switch (data_type) {
+	case FSNOTIFY_EVENT_DENTRY:
+		/* Non const is needed for dget() */
+		return (struct dentry *)data;
+	case FSNOTIFY_EVENT_PATH:
+		return ((const struct path *)data)->dentry;
 	default:
 		return NULL;
 	}
@@ -273,58 +337,110 @@
 	}
 }
 
+static inline struct super_block *fsnotify_data_sb(const void *data,
+						   int data_type)
+{
+	switch (data_type) {
+	case FSNOTIFY_EVENT_INODE:
+		return ((struct inode *)data)->i_sb;
+	case FSNOTIFY_EVENT_DENTRY:
+		return ((struct dentry *)data)->d_sb;
+	case FSNOTIFY_EVENT_PATH:
+		return ((const struct path *)data)->dentry->d_sb;
+	case FSNOTIFY_EVENT_ERROR:
+		return ((struct fs_error_report *) data)->sb;
+	default:
+		return NULL;
+	}
+}
+
+static inline struct fs_error_report *fsnotify_data_error_report(
+							const void *data,
+							int data_type)
+{
+	switch (data_type) {
+	case FSNOTIFY_EVENT_ERROR:
+		return (struct fs_error_report *) data;
+	default:
+		return NULL;
+	}
+}
+
+/*
+ * Index to merged marks iterator array that correlates to a type of watch.
+ * The type of watched object can be deduced from the iterator type, but not
+ * the other way around, because an event can match different watched objects
+ * of the same object type.
+ * For example, both parent and child are watching an object of type inode.
+ */
+enum fsnotify_iter_type {
+	FSNOTIFY_ITER_TYPE_INODE,
+	FSNOTIFY_ITER_TYPE_VFSMOUNT,
+	FSNOTIFY_ITER_TYPE_SB,
+	FSNOTIFY_ITER_TYPE_PARENT,
+	FSNOTIFY_ITER_TYPE_INODE2,
+	FSNOTIFY_ITER_TYPE_COUNT
+};
+
+/* The type of object that a mark is attached to */
 enum fsnotify_obj_type {
+	FSNOTIFY_OBJ_TYPE_ANY = -1,
 	FSNOTIFY_OBJ_TYPE_INODE,
-	FSNOTIFY_OBJ_TYPE_PARENT,
 	FSNOTIFY_OBJ_TYPE_VFSMOUNT,
 	FSNOTIFY_OBJ_TYPE_SB,
 	FSNOTIFY_OBJ_TYPE_COUNT,
 	FSNOTIFY_OBJ_TYPE_DETACHED = FSNOTIFY_OBJ_TYPE_COUNT
 };
 
-#define FSNOTIFY_OBJ_TYPE_INODE_FL	(1U << FSNOTIFY_OBJ_TYPE_INODE)
-#define FSNOTIFY_OBJ_TYPE_PARENT_FL	(1U << FSNOTIFY_OBJ_TYPE_PARENT)
-#define FSNOTIFY_OBJ_TYPE_VFSMOUNT_FL	(1U << FSNOTIFY_OBJ_TYPE_VFSMOUNT)
-#define FSNOTIFY_OBJ_TYPE_SB_FL		(1U << FSNOTIFY_OBJ_TYPE_SB)
-#define FSNOTIFY_OBJ_ALL_TYPES_MASK	((1U << FSNOTIFY_OBJ_TYPE_COUNT) - 1)
-
-static inline bool fsnotify_valid_obj_type(unsigned int type)
+static inline bool fsnotify_valid_obj_type(unsigned int obj_type)
 {
-	return (type < FSNOTIFY_OBJ_TYPE_COUNT);
+	return (obj_type < FSNOTIFY_OBJ_TYPE_COUNT);
 }
 
 struct fsnotify_iter_info {
-	struct fsnotify_mark *marks[FSNOTIFY_OBJ_TYPE_COUNT];
+	struct fsnotify_mark *marks[FSNOTIFY_ITER_TYPE_COUNT];
+	struct fsnotify_group *current_group;
 	unsigned int report_mask;
 	int srcu_idx;
 };
 
 static inline bool fsnotify_iter_should_report_type(
-		struct fsnotify_iter_info *iter_info, int type)
+		struct fsnotify_iter_info *iter_info, int iter_type)
 {
-	return (iter_info->report_mask & (1U << type));
+	return (iter_info->report_mask & (1U << iter_type));
 }
 
 static inline void fsnotify_iter_set_report_type(
-		struct fsnotify_iter_info *iter_info, int type)
+		struct fsnotify_iter_info *iter_info, int iter_type)
 {
-	iter_info->report_mask |= (1U << type);
+	iter_info->report_mask |= (1U << iter_type);
 }
 
-static inline void fsnotify_iter_set_report_type_mark(
-		struct fsnotify_iter_info *iter_info, int type,
-		struct fsnotify_mark *mark)
+static inline struct fsnotify_mark *fsnotify_iter_mark(
+		struct fsnotify_iter_info *iter_info, int iter_type)
 {
-	iter_info->marks[type] = mark;
-	iter_info->report_mask |= (1U << type);
+	if (fsnotify_iter_should_report_type(iter_info, iter_type))
+		return iter_info->marks[iter_type];
+	return NULL;
+}
+
+static inline int fsnotify_iter_step(struct fsnotify_iter_info *iter, int type,
+				     struct fsnotify_mark **markp)
+{
+	while (type < FSNOTIFY_ITER_TYPE_COUNT) {
+		*markp = fsnotify_iter_mark(iter, type);
+		if (*markp)
+			break;
+		type++;
+	}
+	return type;
 }
 
 #define FSNOTIFY_ITER_FUNCS(name, NAME) \
 static inline struct fsnotify_mark *fsnotify_iter_##name##_mark( \
 		struct fsnotify_iter_info *iter_info) \
 { \
-	return (iter_info->report_mask & FSNOTIFY_OBJ_TYPE_##NAME##_FL) ? \
-		iter_info->marks[FSNOTIFY_OBJ_TYPE_##NAME] : NULL; \
+	return fsnotify_iter_mark(iter_info, FSNOTIFY_ITER_TYPE_##NAME); \
 }
 
 FSNOTIFY_ITER_FUNCS(inode, INODE)
@@ -332,8 +448,13 @@
 FSNOTIFY_ITER_FUNCS(vfsmount, VFSMOUNT)
 FSNOTIFY_ITER_FUNCS(sb, SB)
 
-#define fsnotify_foreach_obj_type(type) \
-	for (type = 0; type < FSNOTIFY_OBJ_TYPE_COUNT; type++)
+#define fsnotify_foreach_iter_type(type) \
+	for (type = 0; type < FSNOTIFY_ITER_TYPE_COUNT; type++)
+#define fsnotify_foreach_iter_mark_type(iter, mark, type) \
+	for (type = 0; \
+	     type = fsnotify_iter_step(iter, type, &mark), \
+	     type < FSNOTIFY_ITER_TYPE_COUNT; \
+	     type++)
 
 /*
  * fsnotify_connp_t is what we embed in objects which connector can be attached
@@ -352,6 +473,7 @@
 	spinlock_t lock;
 	unsigned short type;	/* Type of object [lock] */
 #define FSNOTIFY_CONN_FLAG_HAS_FSID	0x01
+#define FSNOTIFY_CONN_FLAG_HAS_IREF	0x02
 	unsigned short flags;	/* flags [lock] */
 	__kernel_fsid_t fsid;	/* fsid of filesystem containing object */
 	union {
@@ -396,11 +518,18 @@
 	struct hlist_node obj_list;
 	/* Head of list of marks for an object [mark ref] */
 	struct fsnotify_mark_connector *connector;
-	/* Events types to ignore [mark->lock, group->mark_mutex] */
-	__u32 ignored_mask;
-#define FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY	0x01
-#define FSNOTIFY_MARK_FLAG_ALIVE		0x02
-#define FSNOTIFY_MARK_FLAG_ATTACHED		0x04
+	/* Events types and flags to ignore [mark->lock, group->mark_mutex] */
+	__u32 ignore_mask;
+	/* General fsnotify mark flags */
+#define FSNOTIFY_MARK_FLAG_ALIVE		0x0001
+#define FSNOTIFY_MARK_FLAG_ATTACHED		0x0002
+	/* inotify mark flags */
+#define FSNOTIFY_MARK_FLAG_EXCL_UNLINK		0x0010
+#define FSNOTIFY_MARK_FLAG_IN_ONESHOT		0x0020
+	/* fanotify mark flags */
+#define FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY	0x0100
+#define FSNOTIFY_MARK_FLAG_NO_IREF		0x0200
+#define FSNOTIFY_MARK_FLAG_HAS_IGNORE_FLAGS	0x0400
 	unsigned int flags;		/* flags [mark->lock] */
 };
 
@@ -434,12 +563,14 @@
 
 static inline int fsnotify_inode_watches_children(struct inode *inode)
 {
+	__u32 parent_mask = READ_ONCE(inode->i_fsnotify_mask);
+
 	/* FS_EVENT_ON_CHILD is set if the inode may care */
-	if (!(inode->i_fsnotify_mask & FS_EVENT_ON_CHILD))
+	if (!(parent_mask & FS_EVENT_ON_CHILD))
 		return 0;
 	/* this inode might care about child events, does it care about the
 	 * specific set of events that can happen on a child? */
-	return inode->i_fsnotify_mask & FS_EVENTS_POSS_ON_CHILD;
+	return parent_mask & FS_EVENTS_POSS_ON_CHILD;
 }
 
 /*
@@ -453,7 +584,7 @@
 	/*
 	 * Serialisation of setting PARENT_WATCHED on the dentries is provided
 	 * by d_lock. If inotify_inode_watched changes after we have taken
-	 * d_lock, the following __fsnotify_update_child_dentry_flags call will
+	 * d_lock, the following fsnotify_set_children_dentry_flags call will
 	 * find our entry, so it will spin until we complete here, and update
 	 * us with the new state.
 	 */
@@ -466,8 +597,9 @@
 /* called from fsnotify listeners, such as fanotify or dnotify */
 
 /* create a new group */
-extern struct fsnotify_group *fsnotify_alloc_group(const struct fsnotify_ops *ops);
-extern struct fsnotify_group *fsnotify_alloc_user_group(const struct fsnotify_ops *ops);
+extern struct fsnotify_group *fsnotify_alloc_group(
+				const struct fsnotify_ops *ops,
+				int flags);
 /* get reference to a group */
 extern void fsnotify_get_group(struct fsnotify_group *group);
 /* drop reference on a group from fsnotify_alloc_group */
@@ -482,16 +614,30 @@
 extern void fsnotify_destroy_event(struct fsnotify_group *group,
 				   struct fsnotify_event *event);
 /* attach the event to the group notification queue */
-extern int fsnotify_add_event(struct fsnotify_group *group,
-			      struct fsnotify_event *event,
-			      int (*merge)(struct fsnotify_group *,
-					   struct fsnotify_event *),
-			      void (*insert)(struct fsnotify_group *,
-					     struct fsnotify_event *));
+extern int fsnotify_insert_event(struct fsnotify_group *group,
+				 struct fsnotify_event *event,
+				 int (*merge)(struct fsnotify_group *,
+					      struct fsnotify_event *),
+				 void (*insert)(struct fsnotify_group *,
+						struct fsnotify_event *));
+
+static inline int fsnotify_add_event(struct fsnotify_group *group,
+				     struct fsnotify_event *event,
+				     int (*merge)(struct fsnotify_group *,
+						  struct fsnotify_event *))
+{
+	return fsnotify_insert_event(group, event, merge, NULL);
+}
+
 /* Queue overflow event to a notification group */
 static inline void fsnotify_queue_overflow(struct fsnotify_group *group)
 {
-	fsnotify_add_event(group, group->overflow_event, NULL, NULL);
+	fsnotify_add_event(group, group->overflow_event, NULL);
+}
+
+static inline bool fsnotify_is_overflow_event(u32 mask)
+{
+	return mask & FS_Q_OVERFLOW;
 }
 
 static inline bool fsnotify_notify_queue_is_empty(struct fsnotify_group *group)
@@ -512,6 +658,101 @@
 
 /* functions used to manipulate the marks attached to inodes */
 
+/*
+ * Canonical "ignore mask" including event flags.
+ *
+ * Note the subtle semantic difference from the legacy ->ignored_mask.
+ * ->ignored_mask traditionally only meant which events should be ignored,
+ * while ->ignore_mask also includes flags regarding the type of objects on
+ * which events should be ignored.
+ */
+static inline __u32 fsnotify_ignore_mask(struct fsnotify_mark *mark)
+{
+	__u32 ignore_mask = mark->ignore_mask;
+
+	/* The event flags in ignore mask take effect */
+	if (mark->flags & FSNOTIFY_MARK_FLAG_HAS_IGNORE_FLAGS)
+		return ignore_mask;
+
+	/*
+	 * Legacy behavior:
+	 * - Always ignore events on dir
+	 * - Ignore events on child if parent is watching children
+	 */
+	ignore_mask |= FS_ISDIR;
+	ignore_mask &= ~FS_EVENT_ON_CHILD;
+	ignore_mask |= mark->mask & FS_EVENT_ON_CHILD;
+
+	return ignore_mask;
+}
+
+/* Legacy ignored_mask - only event types to ignore */
+static inline __u32 fsnotify_ignored_events(struct fsnotify_mark *mark)
+{
+	return mark->ignore_mask & ALL_FSNOTIFY_EVENTS;
+}
+
+/*
+ * Check if mask (or ignore mask) should be applied depending if victim is a
+ * directory and whether it is reported to a watching parent.
+ */
+static inline bool fsnotify_mask_applicable(__u32 mask, bool is_dir,
+					    int iter_type)
+{
+	/* Should mask be applied to a directory? */
+	if (is_dir && !(mask & FS_ISDIR))
+		return false;
+
+	/* Should mask be applied to a child? */
+	if (iter_type == FSNOTIFY_ITER_TYPE_PARENT &&
+	    !(mask & FS_EVENT_ON_CHILD))
+		return false;
+
+	return true;
+}
+
+/*
+ * Effective ignore mask taking into account if event victim is a
+ * directory and whether it is reported to a watching parent.
+ */
+static inline __u32 fsnotify_effective_ignore_mask(struct fsnotify_mark *mark,
+						   bool is_dir, int iter_type)
+{
+	__u32 ignore_mask = fsnotify_ignored_events(mark);
+
+	if (!ignore_mask)
+		return 0;
+
+	/* For non-dir and non-child, no need to consult the event flags */
+	if (!is_dir && iter_type != FSNOTIFY_ITER_TYPE_PARENT)
+		return ignore_mask;
+
+	ignore_mask = fsnotify_ignore_mask(mark);
+	if (!fsnotify_mask_applicable(ignore_mask, is_dir, iter_type))
+		return 0;
+
+	return ignore_mask & ALL_FSNOTIFY_EVENTS;
+}
+
+/* Get mask for calculating object interest taking ignore mask into account */
+static inline __u32 fsnotify_calc_mask(struct fsnotify_mark *mark)
+{
+	__u32 mask = mark->mask;
+
+	if (!fsnotify_ignored_events(mark))
+		return mask;
+
+	/* Interest in FS_MODIFY may be needed for clearing ignore mask */
+	if (!(mark->flags & FSNOTIFY_MARK_FLAG_IGNORED_SURV_MODIFY))
+		mask |= FS_MODIFY;
+
+	/*
+	 * If mark is interested in ignoring events on children, the object must
+	 * show interest in those events for fsnotify_parent() to notice it.
+	 */
+	return mask | mark->ignore_mask;
+}
+
 /* Get mask of events for a list of marks */
 extern __u32 fsnotify_conn_mask(struct fsnotify_mark_connector *conn);
 /* Calculate mask of events for a list of marks */
@@ -526,27 +767,27 @@
 				  __kernel_fsid_t *fsid);
 /* attach the mark to the object */
 extern int fsnotify_add_mark(struct fsnotify_mark *mark,
-			     fsnotify_connp_t *connp, unsigned int type,
-			     int allow_dups, __kernel_fsid_t *fsid);
+			     fsnotify_connp_t *connp, unsigned int obj_type,
+			     int add_flags, __kernel_fsid_t *fsid);
 extern int fsnotify_add_mark_locked(struct fsnotify_mark *mark,
 				    fsnotify_connp_t *connp,
-				    unsigned int type, int allow_dups,
+				    unsigned int obj_type, int add_flags,
 				    __kernel_fsid_t *fsid);
 
 /* attach the mark to the inode */
 static inline int fsnotify_add_inode_mark(struct fsnotify_mark *mark,
 					  struct inode *inode,
-					  int allow_dups)
+					  int add_flags)
 {
 	return fsnotify_add_mark(mark, &inode->i_fsnotify_marks,
-				 FSNOTIFY_OBJ_TYPE_INODE, allow_dups, NULL);
+				 FSNOTIFY_OBJ_TYPE_INODE, add_flags, NULL);
 }
 static inline int fsnotify_add_inode_mark_locked(struct fsnotify_mark *mark,
 						 struct inode *inode,
-						 int allow_dups)
+						 int add_flags)
 {
 	return fsnotify_add_mark_locked(mark, &inode->i_fsnotify_marks,
-					FSNOTIFY_OBJ_TYPE_INODE, allow_dups,
+					FSNOTIFY_OBJ_TYPE_INODE, add_flags,
 					NULL);
 }
 
@@ -559,22 +800,23 @@
 extern void fsnotify_free_mark(struct fsnotify_mark *mark);
 /* Wait until all marks queued for destruction are destroyed */
 extern void fsnotify_wait_marks_destroyed(void);
-/* run all the marks in a group, and clear all of the marks attached to given object type */
-extern void fsnotify_clear_marks_by_group(struct fsnotify_group *group, unsigned int type);
+/* Clear all of the marks of a group attached to a given object type */
+extern void fsnotify_clear_marks_by_group(struct fsnotify_group *group,
+					  unsigned int obj_type);
 /* run all the marks in a group, and clear all of the vfsmount marks */
 static inline void fsnotify_clear_vfsmount_marks_by_group(struct fsnotify_group *group)
 {
-	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_VFSMOUNT_FL);
+	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_VFSMOUNT);
 }
 /* run all the marks in a group, and clear all of the inode marks */
 static inline void fsnotify_clear_inode_marks_by_group(struct fsnotify_group *group)
 {
-	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_INODE_FL);
+	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_INODE);
 }
 /* run all the marks in a group, and clear all of the sn marks */
 static inline void fsnotify_clear_sb_marks_by_group(struct fsnotify_group *group)
 {
-	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_SB_FL);
+	fsnotify_clear_marks_by_group(group, FSNOTIFY_OBJ_TYPE_SB);
 }
 extern void fsnotify_get_mark(struct fsnotify_mark *mark);
 extern void fsnotify_put_mark(struct fsnotify_mark *mark);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ftrace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ftrace.h
@@ -850,7 +850,7 @@
 #define CALLER_ADDR5 ((unsigned long)ftrace_return_address(5))
 #define CALLER_ADDR6 ((unsigned long)ftrace_return_address(6))
 
-static inline unsigned long get_lock_parent_ip(void)
+static __always_inline unsigned long get_lock_parent_ip(void)
 {
 	unsigned long addr = CALLER_ADDR0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/fwnode.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/fwnode.h
@@ -67,7 +67,7 @@
 #define SWNODE_GRAPH_PORT_NAME_FMT		"port@%u"
 #define SWNODE_GRAPH_ENDPOINT_NAME_FMT		"endpoint@%u"
 
-#define NR_FWNODE_REFERENCE_ARGS	8
+#define NR_FWNODE_REFERENCE_ARGS	16
 
 /**
  * struct fwnode_reference_args - Fwnode reference with additional arguments
@@ -147,12 +147,12 @@
 	int (*add_links)(struct fwnode_handle *fwnode);
 };
 
-#define fwnode_has_op(fwnode, op)				\
-	((fwnode) && (fwnode)->ops && (fwnode)->ops->op)
+#define fwnode_has_op(fwnode, op)					\
+	(!IS_ERR_OR_NULL(fwnode) && (fwnode)->ops && (fwnode)->ops->op)
+
 #define fwnode_call_int_op(fwnode, op, ...)				\
-	(fwnode ? (fwnode_has_op(fwnode, op) ?				\
-		   (fwnode)->ops->op(fwnode, ## __VA_ARGS__) : -ENXIO) : \
-	 -EINVAL)
+	(fwnode_has_op(fwnode, op) ?					\
+	 (fwnode)->ops->op(fwnode, ## __VA_ARGS__) : (IS_ERR_OR_NULL(fwnode) ? -EINVAL : -ENXIO))
 
 #define fwnode_call_bool_op(fwnode, op, ...)		\
 	(fwnode_has_op(fwnode, op) ?			\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/genhd.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/genhd.h
@@ -12,12 +12,10 @@
 
 #include <linux/types.h>
 #include <linux/kdev_t.h>
-#include <linux/rcupdate.h>
-#include <linux/slab.h>
-#include <linux/percpu-refcount.h>
 #include <linux/uuid.h>
 #include <linux/blk_types.h>
-#include <asm/local.h>
+#include <linux/device.h>
+#include <linux/xarray.h>
 
 extern const struct device_type disk_type;
 extern struct device_type part_type;
@@ -26,14 +24,6 @@
 #define DISK_MAX_PARTS			256
 #define DISK_NAME_LEN			32
 
-#include <linux/major.h>
-#include <linux/device.h>
-#include <linux/smp.h>
-#include <linux/string.h>
-#include <linux/fs.h>
-#include <linux/workqueue.h>
-#include <linux/xarray.h>
-
 #define PARTITION_META_INFO_VOLNAMELTH	64
 /*
  * Enough for the string representation of any kind of UUID plus NULL.
@@ -70,24 +60,15 @@
  * (``BLOCK_EXT_MAJOR``).
  * This affects the maximum number of partitions.
  *
- * ``GENHD_FL_NATIVE_CAPACITY`` (0x0080): based on information in the
- * partition table, the device's capacity has been extended to its
- * native capacity; i.e. the device has hidden capacity used by one
- * of the partitions (this is a flag used so that native capacity is
- * only ever unlocked once).
- *
- * ``GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE`` (0x0100): event polling is
- * blocked whenever a writer holds an exclusive lock.
- *
- * ``GENHD_FL_NO_PART_SCAN`` (0x0200): partition scanning is disabled.
- * Used for loop devices in their default settings and some MMC
- * devices.
+ * ``GENHD_FL_NO_PART`` (0x0200): partition support is disabled.
+ * The kernel will not scan for partitions from add_disk, and users
+ * can't add partitions manually.
  *
  * ``GENHD_FL_HIDDEN`` (0x0400): the block device is hidden; it
  * doesn't produce events, doesn't appear in sysfs, and doesn't have
  * an associated ``bdev``.
  * Implies ``GENHD_FL_SUPPRESS_PARTITION_INFO`` and
- * ``GENHD_FL_NO_PART_SCAN``.
+ * ``GENHD_FL_NO_PART``.
  * Used for multipath devices.
  */
 #define GENHD_FL_REMOVABLE			0x0001
@@ -96,9 +77,7 @@
 #define GENHD_FL_CD				0x0008
 #define GENHD_FL_SUPPRESS_PARTITION_INFO	0x0020
 #define GENHD_FL_EXT_DEVT			0x0040
-#define GENHD_FL_NATIVE_CAPACITY		0x0080
-#define GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE	0x0100
-#define GENHD_FL_NO_PART_SCAN			0x0200
+#define GENHD_FL_NO_PART			0x0200
 #define GENHD_FL_HIDDEN				0x0400
 
 enum {
@@ -111,6 +90,8 @@
 	DISK_EVENT_FLAG_POLL			= 1 << 0,
 	/* Forward events to udev */
 	DISK_EVENT_FLAG_UEVENT			= 1 << 1,
+	/* Block event polling when open for exclusive write */
+	DISK_EVENT_FLAG_BLOCK_ON_EXCL_WRITE	= 1 << 2,
 };
 
 struct disk_events;
@@ -150,6 +131,8 @@
 #define GD_NEED_PART_SCAN		0
 #define GD_READ_ONLY			1
 #define GD_DEAD				2
+#define GD_NATIVE_CAPACITY		3
+#define GD_SUPPRESS_PART_SCAN		5
 
 	struct mutex open_mutex;	/* open/close mutex */
 	unsigned open_partitions;	/* number of open partitions */
@@ -162,9 +145,6 @@
 	struct timer_rand_state *random;
 	atomic_t sync_io;		/* RAID */
 	struct disk_events *ev;
-#ifdef  CONFIG_BLK_DEV_INTEGRITY
-	struct kobject integrity_kobj;
-#endif	/* CONFIG_BLK_DEV_INTEGRITY */
 #if IS_ENABLED(CONFIG_CDROM)
 	struct cdrom_device_info *cdi;
 #endif
@@ -203,8 +183,9 @@
 
 static inline bool disk_part_scan_enabled(struct gendisk *disk)
 {
-	return disk_max_parts(disk) > 1 &&
-		!(disk->flags & GENHD_FL_NO_PART_SCAN);
+	if (test_bit(GD_SUPPRESS_PART_SCAN, &disk->state))
+		return 0;
+	return disk_max_parts(disk) > 1 && !(disk->flags & GENHD_FL_NO_PART);
 }
 
 static inline dev_t disk_devt(struct gendisk *disk)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/gfp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/gfp.h
@@ -660,6 +660,15 @@
 extern void pm_restrict_gfp_mask(void);
 extern void pm_restore_gfp_mask(void);
 
+/*
+ * Check if the gfp flags allow compaction - GFP_NOIO is a really
+ * tricky context because the migration might require IO.
+ */
+static inline bool gfp_compaction_allowed(gfp_t gfp_mask)
+{
+	return IS_ENABLED(CONFIG_COMPACTION) && (gfp_mask & __GFP_IO);
+}
+
 extern gfp_t vma_thp_gfp_mask(struct vm_area_struct *vma);
 
 #ifdef CONFIG_PM_SLEEP
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/goldfish.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/goldfish.h
@@ -8,14 +8,21 @@
 
 /* Helpers for Goldfish virtual platform */
 
+#ifndef gf_ioread32
+#define gf_ioread32 ioread32
+#endif
+#ifndef gf_iowrite32
+#define gf_iowrite32 iowrite32
+#endif
+
 static inline void gf_write_ptr(const void *ptr, void __iomem *portl,
 				void __iomem *porth)
 {
 	const unsigned long addr = (unsigned long)ptr;
 
-	__raw_writel(lower_32_bits(addr), portl);
+	gf_iowrite32(lower_32_bits(addr), portl);
 #ifdef CONFIG_64BIT
-	__raw_writel(upper_32_bits(addr), porth);
+	gf_iowrite32(upper_32_bits(addr), porth);
 #endif
 }
 
@@ -23,9 +30,9 @@
 				     void __iomem *portl,
 				     void __iomem *porth)
 {
-	__raw_writel(lower_32_bits(addr), portl);
+	gf_iowrite32(lower_32_bits(addr), portl);
 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
-	__raw_writel(upper_32_bits(addr), porth);
+	gf_iowrite32(upper_32_bits(addr), porth);
 #endif
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/gpio/consumer.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/gpio/consumer.h
@@ -8,27 +8,16 @@
 #include <linux/err.h>
 
 struct device;
-
-/**
- * Opaque descriptor for a GPIO. These are obtained using gpiod_get() and are
- * preferable to the old integer-based handles.
- *
- * Contrary to integers, a pointer to a gpio_desc is guaranteed to be valid
- * until the GPIO is released.
- */
 struct gpio_desc;
-
-/**
- * Opaque descriptor for a structure of GPIO array attributes.  This structure
- * is attached to struct gpiod_descs obtained from gpiod_get_array() and can be
- * passed back to get/set array functions in order to activate fast processing
- * path if applicable.
- */
 struct gpio_array;
 
 /**
- * Struct containing an array of descriptors that can be obtained using
- * gpiod_get_array().
+ * struct gpio_descs - Struct containing an array of descriptors that can be
+ *                     obtained using gpiod_get_array()
+ *
+ * @info:	Pointer to the opaque gpio_array structure
+ * @ndescs:	Number of held descriptors
+ * @desc:	Array of pointers to GPIO descriptors
  */
 struct gpio_descs {
 	struct gpio_array *info;
@@ -43,8 +32,16 @@
 #define GPIOD_FLAGS_BIT_NONEXCLUSIVE	BIT(4)
 
 /**
- * Optional flags that can be passed to one of gpiod_* to configure direction
- * and output value. These values cannot be OR'd.
+ * enum gpiod_flags - Optional flags that can be passed to one of gpiod_* to
+ *                    configure direction and output value. These values
+ *                    cannot be OR'd.
+ *
+ * @GPIOD_ASIS:			Don't change anything
+ * @GPIOD_IN:			Set lines to input mode
+ * @GPIOD_OUT_LOW:		Set lines to output and drive them low
+ * @GPIOD_OUT_HIGH:		Set lines to output and drive them high
+ * @GPIOD_OUT_LOW_OPEN_DRAIN:	Set lines to open-drain output and drive them low
+ * @GPIOD_OUT_HIGH_OPEN_DRAIN:	Set lines to open-drain output and drive them high
  */
 enum gpiod_flags {
 	GPIOD_ASIS	= 0,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/gpio/driver.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/gpio/driver.h
@@ -168,11 +168,18 @@
 
 	/**
 	 * @parent_handler_data:
+	 * @parent_handler_data_array:
 	 *
 	 * Data associated, and passed to, the handler for the parent
-	 * interrupt.
-	 */
-	void *parent_handler_data;
+	 * interrupt. Can either be a single pointer if @per_parent_data
+	 * is false, or an array of @num_parents pointers otherwise.  If
+	 * @per_parent_data is true, @parent_handler_data_array cannot be
+	 * NULL.
+	 */
+	union {
+		void *parent_handler_data;
+		void **parent_handler_data_array;
+	};
 
 	/**
 	 * @num_parents:
@@ -204,6 +211,14 @@
 	bool threaded;
 
 	/**
+	 * @per_parent_data:
+	 *
+	 * True if parent_handler_data_array describes a @num_parents
+	 * sized array to be used as parent data.
+	 */
+	bool per_parent_data;
+
+	/**
 	 * @init_hw: optional routine to initialize hardware before
 	 * an IRQ chip will be added. This is quite useful when
 	 * a particular driver wants to clear IRQ related registers
@@ -225,6 +240,15 @@
 				unsigned int ngpios);
 
 	/**
+	 * @initialized:
+	 *
+	 * Flag to track GPIO chip irq member's initialization.
+	 * This flag will make sure GPIO chip irq members are not used
+	 * before they are initialized.
+	 */
+	bool initialized;
+
+	/**
 	 * @valid_mask:
 	 *
 	 * If not %NULL, holds bitmask of GPIOs which are valid to be included
@@ -416,7 +440,7 @@
 	void __iomem *reg_dir_in;
 	bool bgpio_dir_unreadable;
 	int bgpio_bits;
-	spinlock_t bgpio_lock;
+	raw_spinlock_t bgpio_lock;
 	unsigned long bgpio_data;
 	unsigned long bgpio_dir;
 #endif /* CONFIG_GPIO_GENERIC */
@@ -472,6 +496,18 @@
 	 */
 	int (*of_xlate)(struct gpio_chip *gc,
 			const struct of_phandle_args *gpiospec, u32 *flags);
+
+	/**
+	 * @of_gpio_ranges_fallback:
+	 *
+	 * Optional hook for the case that no gpio-ranges property is defined
+	 * within the device tree node "np" (usually DT before introduction
+	 * of gpio-ranges). So this callback is helpful to provide the
+	 * necessary backward compatibility for the pin ranges.
+	 */
+	int (*of_gpio_ranges_fallback)(struct gpio_chip *gc,
+				       struct device_node *np);
+
 #endif /* CONFIG_OF_GPIO */
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/hid.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/hid.h
@@ -349,6 +349,8 @@
 /* BIT(9) reserved for backward compatibility, was NO_INIT_INPUT_REPORTS */
 #define HID_QUIRK_ALWAYS_POLL			BIT(10)
 #define HID_QUIRK_INPUT_PER_APP			BIT(11)
+#define HID_QUIRK_X_INVERT			BIT(12)
+#define HID_QUIRK_Y_INVERT			BIT(13)
 #define HID_QUIRK_SKIP_OUTPUT_REPORTS		BIT(16)
 #define HID_QUIRK_SKIP_OUTPUT_REPORT_ID		BIT(17)
 #define HID_QUIRK_NO_OUTPUT_REPORTS_ON_INTR_EP	BIT(18)
@@ -597,6 +599,7 @@
 	unsigned long status;						/* see STAT flags above */
 	unsigned claimed;						/* Claimed by hidinput, hiddev? */
 	unsigned quirks;						/* Various quirks the device can pull on us */
+	unsigned initial_quirks;					/* Initial set of quirks supplied when creating device */
 	bool io_started;						/* If IO has started */
 
 	struct list_head inputs;					/* The list of inputs */
@@ -627,8 +630,13 @@
 	struct list_head debug_list;
 	spinlock_t  debug_list_lock;
 	wait_queue_head_t debug_wait;
+	struct kref			ref;
+
+	unsigned int id;						/* system unique id */
 };
 
+void hiddev_free(struct kref *ref);
+
 #define to_hid_device(pdev) \
 	container_of(pdev, struct hid_device, dev)
 
@@ -802,6 +810,7 @@
  * @output_report: send output report to device
  * @idle: send idle request to device
  * @may_wakeup: return if device may act as a wakeup source during system-suspend
+ * @max_buffer_size: over-ride maximum data buffer size (default: HID_MAX_BUFFER_SIZE)
  */
 struct hid_ll_driver {
 	int (*start)(struct hid_device *hdev);
@@ -827,6 +836,8 @@
 
 	int (*idle)(struct hid_device *hdev, int report, int idle, int reqtype);
 	bool (*may_wakeup)(struct hid_device *hdev);
+
+	unsigned int max_buffer_size;
 };
 
 extern struct hid_ll_driver i2c_hid_ll_driver;
@@ -840,6 +851,11 @@
 	return hdev->ll_driver == driver;
 }
 
+static inline bool hid_is_usb(struct hid_device *hdev)
+{
+	return hid_is_using_ll_driver(hdev, &usb_hid_driver);
+}
+
 #define	PM_HINT_FULLON	1<<5
 #define PM_HINT_NORMAL	1<<1
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/highmem-internal.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/highmem-internal.h
@@ -184,7 +184,7 @@
 static inline void __kunmap_local(void *addr)
 {
 #ifdef ARCH_HAS_FLUSH_ON_KUNMAP
-	kunmap_flush_on_unmap(addr);
+	kunmap_flush_on_unmap(PTR_ALIGN_DOWN(addr, PAGE_SIZE));
 #endif
 }
 
@@ -211,7 +211,7 @@
 static inline void __kunmap_atomic(void *addr)
 {
 #ifdef ARCH_HAS_FLUSH_ON_KUNMAP
-	kunmap_flush_on_unmap(addr);
+	kunmap_flush_on_unmap(PTR_ALIGN_DOWN(addr, PAGE_SIZE));
 #endif
 	pagefault_enable();
 	if (IS_ENABLED(CONFIG_PREEMPT_RT))
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/highmem.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/highmem.h
@@ -247,6 +247,30 @@
 
 #endif
 
+#ifdef copy_mc_to_kernel
+static inline int copy_mc_user_highpage(struct page *to, struct page *from,
+					unsigned long vaddr, struct vm_area_struct *vma)
+{
+	unsigned long ret;
+	char *vfrom, *vto;
+
+	vfrom = kmap_local_page(from);
+	vto = kmap_local_page(to);
+	ret = copy_mc_to_kernel(vto, vfrom, PAGE_SIZE);
+	kunmap_local(vto);
+	kunmap_local(vfrom);
+
+	return ret;
+}
+#else
+static inline int copy_mc_user_highpage(struct page *to, struct page *from,
+					unsigned long vaddr, struct vm_area_struct *vma)
+{
+	copy_user_highpage(to, from, vaddr, vma);
+	return 0;
+}
+#endif
+
 #ifndef __HAVE_ARCH_COPY_HIGHPAGE
 
 static inline void copy_highpage(struct page *to, struct page *from)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/hrtimer.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/hrtimer.h
@@ -197,6 +197,7 @@
  * @max_hang_time:	Maximum time spent in hrtimer_interrupt
  * @softirq_expiry_lock: Lock which is taken while softirq based hrtimer are
  *			 expired
+ * @online:		CPU is online from an hrtimers point of view
  * @timer_waiters:	A hrtimer_cancel() invocation waits for the timer
  *			callback to finish.
  * @expires_next:	absolute time of the next event, is required for remote
@@ -219,7 +220,8 @@
 	unsigned int			hres_active		: 1,
 					in_hrtirq		: 1,
 					hang_detected		: 1,
-					softirq_activated       : 1;
+					softirq_activated       : 1,
+					online			: 1;
 #ifdef CONFIG_HIGH_RES_TIMERS
 	unsigned int			nr_events;
 	unsigned short			nr_retries;
@@ -530,10 +532,11 @@
 extern void sysrq_timer_list_show(void);
 
 int hrtimers_prepare_cpu(unsigned int cpu);
+int hrtimers_cpu_starting(unsigned int cpu);
 #ifdef CONFIG_HOTPLUG_CPU
-int hrtimers_dead_cpu(unsigned int cpu);
+int hrtimers_cpu_dying(unsigned int cpu);
 #else
-#define hrtimers_dead_cpu	NULL
+#define hrtimers_cpu_dying	NULL
 #endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/hugetlb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/hugetlb.h
@@ -7,6 +7,7 @@
 #include <linux/fs.h>
 #include <linux/hugetlb_inline.h>
 #include <linux/cgroup.h>
+#include <linux/page_ref.h>
 #include <linux/list.h>
 #include <linux/kref.h>
 #include <linux/pgtable.h>
@@ -165,8 +166,9 @@
 						vm_flags_t vm_flags);
 long hugetlb_unreserve_pages(struct inode *inode, long start, long end,
 						long freed);
-bool isolate_huge_page(struct page *page, struct list_head *list);
+int isolate_hugetlb(struct page *page, struct list_head *list);
 int get_hwpoison_huge_page(struct page *page, bool *hugetlb);
+int get_huge_page_for_hwpoison(unsigned long pfn, int flags);
 void putback_active_hugepage(struct page *page);
 void move_hugetlb_state(struct page *oldpage, struct page *newpage, int reason);
 void free_huge_page(struct page *page);
@@ -197,8 +199,8 @@
 struct page *follow_huge_pd(struct vm_area_struct *vma,
 			    unsigned long address, hugepd_t hpd,
 			    int flags, int pdshift);
-struct page *follow_huge_pmd(struct mm_struct *mm, unsigned long address,
-				pmd_t *pmd, int flags);
+struct page *follow_huge_pmd_pte(struct vm_area_struct *vma, unsigned long address,
+				 int flags);
 struct page *follow_huge_pud(struct mm_struct *mm, unsigned long address,
 				pud_t *pud, int flags);
 struct page *follow_huge_pgd(struct mm_struct *mm, unsigned long address,
@@ -285,8 +287,8 @@
 	return NULL;
 }
 
-static inline struct page *follow_huge_pmd(struct mm_struct *mm,
-				unsigned long address, pmd_t *pmd, int flags)
+static inline struct page *follow_huge_pmd_pte(struct vm_area_struct *vma,
+				unsigned long address, int flags)
 {
 	return NULL;
 }
@@ -352,9 +354,9 @@
 	return NULL;
 }
 
-static inline bool isolate_huge_page(struct page *page, struct list_head *list)
+static inline int isolate_hugetlb(struct page *page, struct list_head *list)
 {
-	return false;
+	return -EBUSY;
 }
 
 static inline int get_hwpoison_huge_page(struct page *page, bool *hugetlb)
@@ -362,6 +364,11 @@
 	return 0;
 }
 
+static inline int get_huge_page_for_hwpoison(unsigned long pfn, int flags)
+{
+	return 0;
+}
+
 static inline void putback_active_hugepage(struct page *page)
 {
 }
@@ -593,6 +600,7 @@
 /* Defines one hugetlb page size */
 struct hstate {
 	struct mutex resize_lock;
+	struct lock_class_key resize_key;
 	int next_nid_to_alloc;
 	int next_nid_to_free;
 	unsigned int order;
@@ -677,7 +685,10 @@
 	if (!page_size_log)
 		return &default_hstate;
 
-	return size_to_hstate(1UL << page_size_log);
+	if (page_size_log < BITS_PER_LONG)
+		return size_to_hstate(1UL << page_size_log);
+
+	return NULL;
 }
 
 static inline struct hstate *hstate_vma(struct vm_area_struct *vma)
@@ -1093,6 +1104,18 @@
 }
 #endif
 
+#ifdef CONFIG_ARCH_WANT_HUGE_PMD_SHARE
+static inline bool hugetlb_pmd_shared(pte_t *pte)
+{
+	return page_count(virt_to_page(pte)) > 1;
+}
+#else
+static inline bool hugetlb_pmd_shared(pte_t *pte)
+{
+	return false;
+}
+#endif
+
 bool want_pmd_share(struct vm_area_struct *vma, unsigned long addr);
 
 #ifndef __HAVE_ARCH_FLUSH_HUGETLB_TLB_RANGE
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/hw_random.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/hw_random.h
@@ -60,7 +60,5 @@
 /** Unregister a Hardware Random Number Generator driver. */
 extern void hwrng_unregister(struct hwrng *rng);
 extern void devm_hwrng_unregister(struct device *dve, struct hwrng *rng);
-/** Feed random bits into the pool. */
-extern void add_hwgenerator_randomness(const char *buffer, size_t count, size_t entropy);
 
 #endif /* LINUX_HWRANDOM_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/hwspinlock.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/hwspinlock.h
@@ -68,6 +68,7 @@
 int __hwspin_trylock(struct hwspinlock *, int, unsigned long *);
 void __hwspin_unlock(struct hwspinlock *, int, unsigned long *);
 int of_hwspin_lock_get_id_byname(struct device_node *np, const char *name);
+int hwspin_lock_bust(struct hwspinlock *hwlock, unsigned int id);
 int devm_hwspin_lock_free(struct device *dev, struct hwspinlock *hwlock);
 struct hwspinlock *devm_hwspin_lock_request(struct device *dev);
 struct hwspinlock *devm_hwspin_lock_request_specific(struct device *dev,
@@ -127,6 +128,11 @@
 {
 }
 
+static inline int hwspin_lock_bust(struct hwspinlock *hwlock, unsigned int id)
+{
+	return 0;
+}
+
 static inline int of_hwspin_lock_get_id(struct device_node *np, int index)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/hyperv.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/hyperv.h
@@ -164,8 +164,28 @@
 	u8 buffer[];
 } __packed;
 
+
+/*
+ * If the requested ring buffer size is at least 8 times the size of the
+ * header, steal space from the ring buffer for the header. Otherwise, add
+ * space for the header so that is doesn't take too much of the ring buffer
+ * space.
+ *
+ * The factor of 8 is somewhat arbitrary. The goal is to prevent adding a
+ * relatively small header (4 Kbytes on x86) to a large-ish power-of-2 ring
+ * buffer size (such as 128 Kbytes) and so end up making a nearly twice as
+ * large allocation that will be almost half wasted. As a contrasting example,
+ * on ARM64 with 64 Kbyte page size, we don't want to take 64 Kbytes for the
+ * header from a 128 Kbyte allocation, leaving only 64 Kbytes for the ring.
+ * In this latter case, we must add 64 Kbytes for the header and not worry
+ * about what's wasted.
+ */
+#define VMBUS_HEADER_ADJ(payload_sz) \
+	((payload_sz) >=  8 * sizeof(struct hv_ring_buffer) ? \
+	0 : sizeof(struct hv_ring_buffer))
+
 /* Calculate the proper size of a ringbuffer, it must be page-aligned */
-#define VMBUS_RING_SIZE(payload_sz) PAGE_ALIGN(sizeof(struct hv_ring_buffer) + \
+#define VMBUS_RING_SIZE(payload_sz) PAGE_ALIGN(VMBUS_HEADER_ADJ(payload_sz) + \
 					       (payload_sz))
 
 struct hv_ring_buffer_info {
@@ -344,7 +364,7 @@
 	u8  sender_owns_set;
 	u8 reserved;
 	u32 range_cnt;
-	struct vmtransfer_page_range ranges[1];
+	struct vmtransfer_page_range ranges[];
 } __packed;
 
 struct vmgpadl_packet_header {
@@ -1307,6 +1327,8 @@
 int hv_ringbuffer_get_debuginfo(struct hv_ring_buffer_info *ring_info,
 				struct hv_ring_buffer_debug_info *debug_info);
 
+bool hv_ringbuffer_spinlock_busy(struct vmbus_channel *channel);
+
 /* Vmbus interface */
 #define vmbus_driver_register(driver)	\
 	__vmbus_driver_register(driver, THIS_MODULE, KBUILD_MODNAME)
@@ -1504,6 +1526,7 @@
 	void *channel;
 	void (*util_cb)(void *);
 	int (*util_init)(struct hv_util_service *);
+	int (*util_init_transport)(void);
 	void (*util_deinit)(void);
 	int (*util_pre_suspend)(void);
 	int (*util_pre_resume)(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/i2c-smbus.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/i2c-smbus.h
@@ -30,10 +30,10 @@
 					      struct i2c_smbus_alert_setup *setup);
 int i2c_handle_smbus_alert(struct i2c_client *ara);
 
-#if IS_ENABLED(CONFIG_I2C_SMBUS) && IS_ENABLED(CONFIG_OF)
-int of_i2c_setup_smbus_alert(struct i2c_adapter *adap);
+#if IS_ENABLED(CONFIG_I2C_SMBUS)
+int i2c_setup_smbus_alert(struct i2c_adapter *adap);
 #else
-static inline int of_i2c_setup_smbus_alert(struct i2c_adapter *adap)
+static inline int i2c_setup_smbus_alert(struct i2c_adapter *adap)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/i2c.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/i2c.h
@@ -349,6 +349,8 @@
 const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id,
 					 const struct i2c_client *client);
 
+const void *i2c_get_match_data(const struct i2c_client *client);
+
 static inline struct i2c_client *kobj_to_i2c_client(struct kobject *kobj)
 {
 	struct device * const dev = kobj_to_dev(kobj);
@@ -738,6 +740,11 @@
 
 	struct irq_domain *host_notify_domain;
 	struct regulator *bus_regulator;
+
+	struct dentry *debugfs;
+
+	/* 7bit address space */
+	DECLARE_BITMAP(addrs_in_instantiation, 1 << 7);
 };
 #define to_i2c_adapter(d) container_of(d, struct i2c_adapter, dev)
 
@@ -954,15 +961,33 @@
 
 #endif /* I2C */
 
+/* must call put_device() when done with returned i2c_client device */
+struct i2c_client *i2c_find_device_by_fwnode(struct fwnode_handle *fwnode);
+
+/* must call put_device() when done with returned i2c_adapter device */
+struct i2c_adapter *i2c_find_adapter_by_fwnode(struct fwnode_handle *fwnode);
+
+/* must call i2c_put_adapter() when done with returned i2c_adapter device */
+struct i2c_adapter *i2c_get_adapter_by_fwnode(struct fwnode_handle *fwnode);
+
 #if IS_ENABLED(CONFIG_OF)
 /* must call put_device() when done with returned i2c_client device */
-struct i2c_client *of_find_i2c_device_by_node(struct device_node *node);
+static inline struct i2c_client *of_find_i2c_device_by_node(struct device_node *node)
+{
+	return i2c_find_device_by_fwnode(of_fwnode_handle(node));
+}
 
 /* must call put_device() when done with returned i2c_adapter device */
-struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node);
+static inline struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node)
+{
+	return i2c_find_adapter_by_fwnode(of_fwnode_handle(node));
+}
 
 /* must call i2c_put_adapter() when done with returned i2c_adapter device */
-struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node);
+static inline struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node)
+{
+	return i2c_get_adapter_by_fwnode(of_fwnode_handle(node));
+}
 
 const struct of_device_id
 *i2c_of_match_device(const struct of_device_id *matches,
@@ -1007,7 +1032,7 @@
 struct acpi_resource;
 struct acpi_resource_i2c_serialbus;
 
-#if IS_ENABLED(CONFIG_ACPI)
+#if IS_REACHABLE(CONFIG_ACPI) && IS_REACHABLE(CONFIG_I2C)
 bool i2c_acpi_get_i2c_resource(struct acpi_resource *ares,
 			       struct acpi_resource_i2c_serialbus **i2c);
 int i2c_acpi_client_count(struct acpi_device *adev);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/i8253.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/i8253.h
@@ -21,9 +21,9 @@
 #define PIT_LATCH	((PIT_TICK_RATE + HZ/2) / HZ)
 
 extern raw_spinlock_t i8253_lock;
-extern bool i8253_clear_counter_on_shutdown;
 extern struct clock_event_device i8253_clockevent;
 extern void clockevent_i8253_init(bool oneshot);
+extern void clockevent_i8253_disable(void);
 
 extern void setup_pit_timer(void);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/idr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/idr.h
@@ -171,7 +171,7 @@
  */
 static inline void idr_preload_end(void)
 {
-	local_unlock(&radix_tree_preloads.lock);
+	preempt_enable();
 }
 
 /**
@@ -200,7 +200,7 @@
  */
 #define idr_for_each_entry_ul(idr, entry, tmp, id)			\
 	for (tmp = 0, id = 0;						\
-	     tmp <= id && ((entry) = idr_get_next_ul(idr, &(id))) != NULL; \
+	     ((entry) = tmp <= id ? idr_get_next_ul(idr, &(id)) : NULL) != NULL; \
 	     tmp = id, ++id)
 
 /**
@@ -224,10 +224,12 @@
  * @id: Entry ID.
  *
  * Continue to iterate over entries, continuing after the current position.
+ * After normal termination @entry is left with the value NULL.  This
+ * is convenient for a "not found" value.
  */
 #define idr_for_each_entry_continue_ul(idr, entry, tmp, id)		\
 	for (tmp = id;							\
-	     tmp <= id && ((entry) = idr_get_next_ul(idr, &(id))) != NULL; \
+	     ((entry) = tmp <= id ? idr_get_next_ul(idr, &(id)) : NULL) != NULL; \
 	     tmp = id, ++id)
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ieee80211.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ieee80211.h
@@ -1023,6 +1023,8 @@
 #define IEEE80211_ADDBA_EXT_FRAG_LEVEL_MASK	GENMASK(2, 1)
 #define IEEE80211_ADDBA_EXT_FRAG_LEVEL_SHIFT	1
 #define IEEE80211_ADDBA_EXT_NO_FRAG		BIT(0)
+#define IEEE80211_ADDBA_EXT_BUF_SIZE_MASK	GENMASK(7, 5)
+#define IEEE80211_ADDBA_EXT_BUF_SIZE_SHIFT	10
 
 struct ieee80211_addba_ext_ie {
 	u8 data;
@@ -1697,10 +1699,12 @@
  * A-MPDU buffer sizes
  * According to HT size varies from 8 to 64 frames
  * HE adds the ability to have up to 256 frames.
+ * EHT adds the ability to have up to 1K frames.
  */
 #define IEEE80211_MIN_AMPDU_BUF		0x8
 #define IEEE80211_MAX_AMPDU_BUF_HT	0x40
-#define IEEE80211_MAX_AMPDU_BUF		0x100
+#define IEEE80211_MAX_AMPDU_BUF_HE	0x100
+#define IEEE80211_MAX_AMPDU_BUF_EHT	0x400
 
 
 /* Spatial Multiplexing Power Save Modes (for capability) */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/if_arp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/if_arp.h
@@ -52,6 +52,11 @@
 	case ARPHRD_VOID:
 	case ARPHRD_NONE:
 	case ARPHRD_RAWIP:
+	case ARPHRD_PIMREG:
+	/* PPP adds its l2 header automatically in ppp_start_xmit().
+	 * This makes it look like an l3 device to __bpf_redirect() and tcf_mirred_init().
+	 */
+	case ARPHRD_PPP:
 		return false;
 	default:
 		return true;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/if_team.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/if_team.h
@@ -189,6 +189,8 @@
 	struct net_device *dev; /* associated netdevice */
 	struct team_pcpu_stats __percpu *pcpu_stats;
 
+	const struct header_ops *header_ops_cache;
+
 	struct mutex lock; /* used for overall locking, e.g. port lists write */
 
 	/*
@@ -208,6 +210,7 @@
 	bool queue_override_enabled;
 	struct list_head *qom_lists; /* array of queue override mapping lists */
 	bool port_mtu_change_allowed;
+	bool notifier_ctx;
 	struct {
 		unsigned int count;
 		unsigned int interval; /* in ms */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/if_vlan.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/if_vlan.h
@@ -60,6 +60,14 @@
 	return (struct vlan_ethhdr *)skb_mac_header(skb);
 }
 
+/* Prefer this version in TX path, instead of
+ * skb_reset_mac_header() + vlan_eth_hdr()
+ */
+static inline struct vlan_ethhdr *skb_vlan_eth_hdr(const struct sk_buff *skb)
+{
+	return (struct vlan_ethhdr *)skb->data;
+}
+
 #define VLAN_PRIO_MASK		0xe000 /* Priority Code Point */
 #define VLAN_PRIO_SHIFT		13
 #define VLAN_CFI_MASK		0x1000 /* Canonical Format Indicator / Drop Eligible Indicator */
@@ -526,7 +534,7 @@
  */
 static inline int __vlan_get_tag(const struct sk_buff *skb, u16 *vlan_tci)
 {
-	struct vlan_ethhdr *veth = (struct vlan_ethhdr *)skb->data;
+	struct vlan_ethhdr *veth = skb_vlan_eth_hdr(skb);
 
 	if (!eth_type_vlan(veth->h_vlan_proto))
 		return -EINVAL;
@@ -574,13 +582,16 @@
  * vlan_get_protocol - get protocol EtherType.
  * @skb: skbuff to query
  * @type: first vlan protocol
+ * @mac_offset: MAC offset
  * @depth: buffer to store length of eth and vlan tags in bytes
  *
  * Returns the EtherType of the packet, regardless of whether it is
  * vlan encapsulated (normal or hardware accelerated) or not.
  */
-static inline __be16 __vlan_get_protocol(const struct sk_buff *skb, __be16 type,
-					 int *depth)
+static inline __be16 __vlan_get_protocol_offset(const struct sk_buff *skb,
+						__be16 type,
+						int mac_offset,
+						int *depth)
 {
 	unsigned int vlan_depth = skb->mac_len, parse_depth = VLAN_MAX_DEPTH;
 
@@ -599,7 +610,8 @@
 		do {
 			struct vlan_hdr vhdr, *vh;
 
-			vh = skb_header_pointer(skb, vlan_depth, sizeof(vhdr), &vhdr);
+			vh = skb_header_pointer(skb, mac_offset + vlan_depth,
+						sizeof(vhdr), &vhdr);
 			if (unlikely(!vh || !--parse_depth))
 				return 0;
 
@@ -614,6 +626,12 @@
 	return type;
 }
 
+static inline __be16 __vlan_get_protocol(const struct sk_buff *skb, __be16 type,
+					 int *depth)
+{
+	return __vlan_get_protocol_offset(skb, type, 0, depth);
+}
+
 /**
  * vlan_get_protocol - get protocol EtherType.
  * @skb: skbuff to query
@@ -626,6 +644,23 @@
 	return __vlan_get_protocol(skb, skb->protocol, NULL);
 }
 
+/* This version of __vlan_get_protocol() also pulls mac header in skb->head */
+static inline __be16 vlan_get_protocol_and_depth(struct sk_buff *skb,
+						 __be16 type, int *depth)
+{
+	int maclen;
+
+	type = __vlan_get_protocol(skb, type, &maclen);
+
+	if (type) {
+		if (!pskb_may_pull(skb, maclen))
+			type = 0;
+		else if (depth)
+			*depth = maclen;
+	}
+	return type;
+}
+
 /* A getter for the SKB protocol field which will handle VLAN tags consistently
  * whether VLAN acceleration is enabled or not.
  */
@@ -710,7 +745,7 @@
 		if (unlikely(!pskb_may_pull(skb, VLAN_ETH_HLEN)))
 			return false;
 
-		veh = (struct vlan_ethhdr *)skb->data;
+		veh = skb_vlan_eth_hdr(skb);
 		protocol = veh->h_vlan_encapsulated_proto;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/igmp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/igmp.h
@@ -118,9 +118,9 @@
 		struct ip_mreq_source *mreqs, int ifindex);
 extern int ip_mc_msfilter(struct sock *sk, struct ip_msfilter *msf,int ifindex);
 extern int ip_mc_msfget(struct sock *sk, struct ip_msfilter *msf,
-		struct ip_msfilter __user *optval, int __user *optlen);
+			sockptr_t optval, sockptr_t optlen);
 extern int ip_mc_gsfget(struct sock *sk, struct group_filter *gsf,
-			struct sockaddr_storage __user *p);
+			sockptr_t optval, size_t offset);
 extern int ip_mc_sf_allow(struct sock *sk, __be32 local, __be32 rmt,
 			  int dif, int sdif);
 extern void ip_mc_init_dev(struct in_device *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/adc/adi-axi-adc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/adc/adi-axi-adc.h
@@ -41,6 +41,7 @@
  * @reg_access		IIO debugfs_reg_access hook for the client ADC
  * @read_raw		IIO read_raw hook for the client ADC
  * @write_raw		IIO write_raw hook for the client ADC
+ * @read_avail		IIO read_avail hook for the client ADC
  */
 struct adi_axi_adc_conv {
 	const struct adi_axi_adc_chip_info		*chip_info;
@@ -54,6 +55,9 @@
 	int (*write_raw)(struct adi_axi_adc_conv *conv,
 			 struct iio_chan_spec const *chan,
 			 int val, int val2, long mask);
+	int (*read_avail)(struct adi_axi_adc_conv *conv,
+			  struct iio_chan_spec const *chan,
+			  const int **val, int *type, int *length, long mask);
 };
 
 struct adi_axi_adc_conv *devm_adi_axi_adc_conv_register(struct device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/adc/versal-sysmon-events.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/adc/versal-sysmon-events.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx SYSMON hardware info
+ *
+ * Copyright (C) 2019 - 2021 Xilinx, Inc.
+ *
+ */
+#ifndef _VERSAL_SYSMON_H_
+#define _VERSAL_SYSMON_H_
+
+#include <linux/types.h>
+#include <linux/iio/types.h>
+
+/* Sysmon region ids */
+enum sysmon_region {
+	SYSMON_AIE = 0,
+	SYSMON_PMC = 1,
+	SYSMON_XPIO = 2,
+	SYSMON_VNOC = 3,
+	SYSMON_CC = 4,
+};
+
+/**
+ * struct regional_node - regional node properties
+ * @sat_id: node_id
+ * @x: x co-ordinate of the node
+ * @y: y co-ordinate of the node
+ * @temp: raw sensor value
+ * @regional_node_list: list of nodes in the region
+ */
+struct regional_node {
+	int sat_id;
+	int x;
+	int y;
+	u16 temp;
+	struct list_head regional_node_list;
+};
+
+/**
+ * struct region_info - information about a regions sensors
+ * @id: region id
+ * @cb: callback to be called when there is a region specific event
+ * @data: pointer to the callback data
+ * @node_list: head to the regional_nodes list
+ * @list: list of regions
+ */
+struct region_info {
+	enum sysmon_region id;
+	void (*cb)(void *data, struct regional_node *node);
+	void *data;
+	struct list_head node_list;
+	struct list_head list;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/afe/rescale.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/afe/rescale.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2018 Axentia Technologies AB
+ */
+
+#ifndef __IIO_RESCALE_H__
+#define __IIO_RESCALE_H__
+
+#include <linux/types.h>
+#include <linux/iio/iio.h>
+
+struct device;
+struct rescale;
+
+struct rescale_cfg {
+	enum iio_chan_type type;
+	int (*props)(struct device *dev, struct rescale *rescale);
+};
+
+struct rescale {
+	const struct rescale_cfg *cfg;
+	struct iio_channel *source;
+	struct iio_chan_spec chan;
+	struct iio_chan_spec_ext_info *ext_info;
+	bool chan_processed;
+	s32 numerator;
+	s32 denominator;
+	s32 offset;
+};
+
+int rescale_process_scale(struct rescale *rescale, int scale_type,
+			  int *val, int *val2);
+int rescale_process_offset(struct rescale *rescale, int scale_type,
+			   int scale, int scale2, int schan_off,
+			   int *val, int *val2);
+#endif /* __IIO_RESCALE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/common/cros_ec_sensors_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/common/cros_ec_sensors_core.h
@@ -95,8 +95,11 @@
 struct platform_device;
 int cros_ec_sensors_core_init(struct platform_device *pdev,
 			      struct iio_dev *indio_dev, bool physical_device,
-			      cros_ec_sensors_capture_t trigger_capture,
-			      cros_ec_sensorhub_push_data_cb_t push_data);
+			      cros_ec_sensors_capture_t trigger_capture);
+
+int cros_ec_sensors_core_register(struct device *dev,
+				  struct iio_dev *indio_dev,
+				  cros_ec_sensorhub_push_data_cb_t push_data);
 
 irqreturn_t cros_ec_sensors_capture(int irq, void *p);
 int cros_ec_sensors_push_data(struct iio_dev *indio_dev,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/common/st_sensors.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/common/st_sensors.h
@@ -238,6 +238,7 @@
  * @hw_irq_trigger: if we're using the hardware interrupt on the sensor.
  * @hw_timestamp: Latest timestamp from the interrupt handler, when in use.
  * @buffer_data: Data used by buffer part.
+ * @odr_lock: Local lock for preventing concurrent ODR accesses/changes
  */
 struct st_sensor_data {
 	struct device *dev;
@@ -263,6 +264,8 @@
 	s64 hw_timestamp;
 
 	char buffer_data[ST_SENSORS_MAX_BUFFER_SIZE] ____cacheline_aligned;
+
+	struct mutex odr_lock;
 };
 
 #ifdef CONFIG_IIO_BUFFER
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/iio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/iio.h
@@ -542,6 +542,8 @@
 };
 
 int iio_device_id(struct iio_dev *indio_dev);
+int iio_device_get_current_mode(struct iio_dev *indio_dev);
+bool iio_buffer_enabled(struct iio_dev *indio_dev);
 
 const struct iio_chan_spec
 *iio_find_channel_from_si(struct iio_dev *indio_dev, int si);
@@ -573,6 +575,8 @@
 int iio_push_event(struct iio_dev *indio_dev, u64 ev_code, s64 timestamp);
 int iio_device_claim_direct_mode(struct iio_dev *indio_dev);
 void iio_device_release_direct_mode(struct iio_dev *indio_dev);
+int iio_device_claim_buffer_mode(struct iio_dev *indio_dev);
+void iio_device_release_buffer_mode(struct iio_dev *indio_dev);
 
 extern struct bus_type iio_bus_type;
 
@@ -671,16 +675,6 @@
 __printf(2, 3)
 struct iio_trigger *devm_iio_trigger_alloc(struct device *parent,
 					   const char *fmt, ...);
-/**
- * iio_buffer_enabled() - helper function to test if the buffer is enabled
- * @indio_dev:		IIO device structure for device
- **/
-static inline bool iio_buffer_enabled(struct iio_dev *indio_dev)
-{
-	return indio_dev->currentmode
-		& (INDIO_BUFFER_TRIGGERED | INDIO_BUFFER_HARDWARE |
-		   INDIO_BUFFER_SOFTWARE);
-}
 
 /**
  * iio_get_debugfs_dentry() - helper function to get the debugfs_dentry
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/imu/adis.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/imu/adis.h
@@ -32,6 +32,7 @@
 	u16 sw_reset_ms;
 	u16 self_test_ms;
 };
+
 /**
  * struct adis_data - ADIS chip variant specific data
  * @read_delay: SPI delay for read operations in us
@@ -45,10 +46,11 @@
  * @self_test_mask: Bitmask of supported self-test operations
  * @self_test_reg: Register address to request self test command
  * @self_test_no_autoclear: True if device's self-test needs clear of ctrl reg
- * @status_error_msgs: Array of error messgaes
+ * @status_error_msgs: Array of error messages
  * @status_error_mask: Bitmask of errors supported by the device
  * @timeouts: Chip specific delays
  * @enable_irq: Hook for ADIS devices that have a special IRQ enable/disable
+ * @unmasked_drdy: True for devices that cannot mask/unmask the data ready pin
  * @has_paging: True if ADIS device has paged registers
  * @burst_reg_cmd:	Register command that triggers burst
  * @burst_len:		Burst size in the SPI RX buffer. If @burst_max_len is defined,
@@ -78,6 +80,7 @@
 	unsigned int status_error_mask;
 
 	int (*enable_irq)(struct adis *adis, bool enable);
+	bool unmasked_drdy;
 
 	bool has_paging;
 
@@ -128,12 +131,12 @@
 	unsigned long		irq_flag;
 	void			*buffer;
 
-	uint8_t			tx[10] ____cacheline_aligned;
-	uint8_t			rx[4];
+	u8			tx[10] ____cacheline_aligned;
+	u8			rx[4];
 };
 
 int adis_init(struct adis *adis, struct iio_dev *indio_dev,
-	struct spi_device *spi, const struct adis_data *data);
+	      struct spi_device *spi, const struct adis_data *data);
 int __adis_reset(struct adis *adis);
 
 /**
@@ -154,9 +157,9 @@
 }
 
 int __adis_write_reg(struct adis *adis, unsigned int reg,
-	unsigned int val, unsigned int size);
+		     unsigned int val, unsigned int size);
 int __adis_read_reg(struct adis *adis, unsigned int reg,
-	unsigned int *val, unsigned int size);
+		    unsigned int *val, unsigned int size);
 
 /**
  * __adis_write_reg_8() - Write single byte to a register (unlocked)
@@ -165,7 +168,7 @@
  * @value: The value to write
  */
 static inline int __adis_write_reg_8(struct adis *adis, unsigned int reg,
-	uint8_t val)
+				     u8 val)
 {
 	return __adis_write_reg(adis, reg, val, 1);
 }
@@ -177,7 +180,7 @@
  * @value: Value to be written
  */
 static inline int __adis_write_reg_16(struct adis *adis, unsigned int reg,
-	uint16_t val)
+				      u16 val)
 {
 	return __adis_write_reg(adis, reg, val, 2);
 }
@@ -189,7 +192,7 @@
  * @value: Value to be written
  */
 static inline int __adis_write_reg_32(struct adis *adis, unsigned int reg,
-	uint32_t val)
+				      u32 val)
 {
 	return __adis_write_reg(adis, reg, val, 4);
 }
@@ -201,7 +204,7 @@
  * @val: The value read back from the device
  */
 static inline int __adis_read_reg_16(struct adis *adis, unsigned int reg,
-	uint16_t *val)
+				     u16 *val)
 {
 	unsigned int tmp;
 	int ret;
@@ -220,7 +223,7 @@
  * @val: The value read back from the device
  */
 static inline int __adis_read_reg_32(struct adis *adis, unsigned int reg,
-	uint32_t *val)
+				     u32 *val)
 {
 	unsigned int tmp;
 	int ret;
@@ -240,7 +243,7 @@
  * @size: The size of the @value (in bytes)
  */
 static inline int adis_write_reg(struct adis *adis, unsigned int reg,
-	unsigned int val, unsigned int size)
+				 unsigned int val, unsigned int size)
 {
 	int ret;
 
@@ -259,7 +262,7 @@
  * @size: The size of the @val buffer
  */
 static int adis_read_reg(struct adis *adis, unsigned int reg,
-	unsigned int *val, unsigned int size)
+			 unsigned int *val, unsigned int size)
 {
 	int ret;
 
@@ -277,7 +280,7 @@
  * @value: The value to write
  */
 static inline int adis_write_reg_8(struct adis *adis, unsigned int reg,
-	uint8_t val)
+				   u8 val)
 {
 	return adis_write_reg(adis, reg, val, 1);
 }
@@ -289,7 +292,7 @@
  * @value: Value to be written
  */
 static inline int adis_write_reg_16(struct adis *adis, unsigned int reg,
-	uint16_t val)
+				    u16 val)
 {
 	return adis_write_reg(adis, reg, val, 2);
 }
@@ -301,7 +304,7 @@
  * @value: Value to be written
  */
 static inline int adis_write_reg_32(struct adis *adis, unsigned int reg,
-	uint32_t val)
+				    u32 val)
 {
 	return adis_write_reg(adis, reg, val, 4);
 }
@@ -313,7 +316,7 @@
  * @val: The value read back from the device
  */
 static inline int adis_read_reg_16(struct adis *adis, unsigned int reg,
-	uint16_t *val)
+				   u16 *val)
 {
 	unsigned int tmp;
 	int ret;
@@ -332,7 +335,7 @@
  * @val: The value read back from the device
  */
 static inline int adis_read_reg_32(struct adis *adis, unsigned int reg,
-	uint32_t *val)
+				   u32 *val)
 {
 	unsigned int tmp;
 	int ret;
@@ -403,9 +406,20 @@
 		__adis_update_bits_base(adis, reg, mask, val, 2));	\
 })
 
-int adis_enable_irq(struct adis *adis, bool enable);
 int __adis_check_status(struct adis *adis);
 int __adis_initial_startup(struct adis *adis);
+int __adis_enable_irq(struct adis *adis, bool enable);
+
+static inline int adis_enable_irq(struct adis *adis, bool enable)
+{
+	int ret;
+
+	mutex_lock(&adis->state_lock);
+	ret = __adis_enable_irq(adis, enable);
+	mutex_unlock(&adis->state_lock);
+
+	return ret;
+}
 
 static inline int adis_check_status(struct adis *adis)
 {
@@ -441,8 +455,8 @@
 }
 
 int adis_single_conversion(struct iio_dev *indio_dev,
-	const struct iio_chan_spec *chan, unsigned int error_mask,
-	int *val);
+			   const struct iio_chan_spec *chan,
+			   unsigned int error_mask, int *val);
 
 #define ADIS_VOLTAGE_CHAN(addr, si, chan, name, info_all, bits) { \
 	.type = IIO_VOLTAGE, \
@@ -491,7 +505,7 @@
 	.modified = 1, \
 	.channel2 = IIO_MOD_ ## mod, \
 	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
-		 info_sep, \
+		 (info_sep), \
 	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
 	.info_mask_shared_by_all = info_all, \
 	.address = (addr), \
@@ -525,7 +539,7 @@
 int devm_adis_probe_trigger(struct adis *adis, struct iio_dev *indio_dev);
 
 int adis_update_scan_mode(struct iio_dev *indio_dev,
-	const unsigned long *scan_mask);
+			  const unsigned long *scan_mask);
 
 #else /* CONFIG_IIO_BUFFER */
 
@@ -549,7 +563,8 @@
 #ifdef CONFIG_DEBUG_FS
 
 int adis_debugfs_reg_access(struct iio_dev *indio_dev,
-	unsigned int reg, unsigned int writeval, unsigned int *readval);
+			    unsigned int reg, unsigned int writeval,
+			    unsigned int *readval);
 
 #else
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iio/trigger.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iio/trigger.h
@@ -55,6 +55,7 @@
  * @attached_own_device:[INTERN] if we are using our own device as trigger,
  *			i.e. if we registered a poll function to the same
  *			device as the one providing the trigger.
+ * @reenable_work:	[INTERN] work item used to ensure reenable can sleep.
  **/
 struct iio_trigger {
 	const struct iio_trigger_ops	*ops;
@@ -74,6 +75,7 @@
 	unsigned long pool[BITS_TO_LONGS(CONFIG_IIO_CONSUMERS_PER_TRIGGER)];
 	struct mutex			pool_lock;
 	bool				attached_own_device;
+	struct work_struct		reenable_work;
 };
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ima.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ima.h
@@ -21,7 +21,8 @@
 extern void ima_post_create_tmpfile(struct user_namespace *mnt_userns,
 				    struct inode *inode);
 extern void ima_file_free(struct file *file);
-extern int ima_file_mmap(struct file *file, unsigned long prot);
+extern int ima_file_mmap(struct file *file, unsigned long reqprot,
+			 unsigned long prot, unsigned long flags);
 extern int ima_file_mprotect(struct vm_area_struct *vma, unsigned long prot);
 extern int ima_load_data(enum kernel_load_data_id id, bool contents);
 extern int ima_post_load_data(char *buf, loff_t size,
@@ -91,7 +92,8 @@
 	return;
 }
 
-static inline int ima_file_mmap(struct file *file, unsigned long prot)
+static inline int ima_file_mmap(struct file *file, unsigned long reqprot,
+				unsigned long prot, unsigned long flags)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/instrumentation.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/instrumentation.h
@@ -11,7 +11,7 @@
 	asm volatile(__stringify(c) ": nop\n\t"				\
 		     ".pushsection .discard.instr_begin\n\t"		\
 		     ".long " __stringify(c) "b - .\n\t"		\
-		     ".popsection\n\t");				\
+		     ".popsection\n\t" : : "i" (c));			\
 })
 #define instrumentation_begin() __instrumentation_begin(__COUNTER__)
 
@@ -50,7 +50,7 @@
 	asm volatile(__stringify(c) ": nop\n\t"				\
 		     ".pushsection .discard.instr_end\n\t"		\
 		     ".long " __stringify(c) "b - .\n\t"		\
-		     ".popsection\n\t");				\
+		     ".popsection\n\t" : : "i" (c));			\
 })
 #define instrumentation_end() __instrumentation_end(__COUNTER__)
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/intel-iommu.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/intel-iommu.h
@@ -196,7 +196,6 @@
 #define ecap_dis(e)		(((e) >> 27) & 0x1)
 #define ecap_nest(e)		(((e) >> 26) & 0x1)
 #define ecap_mts(e)		(((e) >> 25) & 0x1)
-#define ecap_ecs(e)		(((e) >> 24) & 0x1)
 #define ecap_iotlb_offset(e) 	((((e) >> 8) & 0x3ff) * 16)
 #define ecap_max_iotlb_offset(e) (ecap_iotlb_offset(e) + 16)
 #define ecap_coherent(e)	((e) & 0x1)
@@ -264,7 +263,6 @@
 #define DMA_GSTS_CFIS (((u32)1) << 23)
 
 /* DMA_RTADDR_REG */
-#define DMA_RTADDR_RTT (((u64)1) << 11)
 #define DMA_RTADDR_SMT (((u64)1) << 10)
 
 /* CCMD_REG */
@@ -517,9 +515,6 @@
 	u64 hi;
 };
 
-/* si_domain contains mulitple devices */
-#define DOMAIN_FLAG_STATIC_IDENTITY		BIT(0)
-
 /*
  * When VT-d works in the scalable mode, it allows DMA translation to
  * happen through either first level or second level page table. This
@@ -594,6 +589,7 @@
 #ifdef CONFIG_INTEL_IOMMU
 	unsigned long 	*domain_ids; /* bitmap of domains */
 	struct dmar_domain ***domains; /* ptr to domains */
+	unsigned long	*copied_tables; /* bitmap of copied tables */
 	spinlock_t	lock; /* protect context, domain ids */
 	struct root_entry *root_entry; /* virtual address */
 
@@ -608,7 +604,7 @@
 	struct iopf_queue *iopf_queue;
 	unsigned char iopfq_name[16];
 	struct q_inval  *qi;            /* Queued invalidation info */
-	u32 *iommu_state; /* Store iommu states between suspend and resume.*/
+	u32 iommu_state[MAX_SR_DMAR_REGS]; /* Store iommu states between suspend and resume.*/
 
 #ifdef CONFIG_IRQ_REMAP
 	struct ir_table *ir_table;	/* Interrupt remapping info */
@@ -636,7 +632,6 @@
 struct device_domain_info {
 	struct list_head link;	/* link to domain siblings */
 	struct list_head global; /* link to global list */
-	struct list_head table;	/* link to pasid table */
 	struct list_head subdevices; /* subdevices sibling */
 	u32 segment;		/* PCI segment number */
 	u8 bus;			/* PCI bus number */
@@ -713,6 +708,11 @@
 	return !((unsigned long)pte & ~VTD_PAGE_MASK);
 }
 
+static inline bool context_present(struct context_entry *context)
+{
+	return (context->lo & 1);
+}
+
 extern struct dmar_drhd_unit * dmar_find_matched_drhd_unit(struct pci_dev *dev);
 extern int dmar_find_matched_atsr_unit(struct pci_dev *dev);
 
@@ -750,8 +750,6 @@
 void *alloc_pgtable_page(int node);
 void free_pgtable_page(void *vaddr);
 struct intel_iommu *domain_get_iommu(struct dmar_domain *domain);
-int for_each_device_domain(int (*fn)(struct device_domain_info *info,
-				     void *data), void *data);
 void iommu_flush_write_buffer(struct intel_iommu *iommu);
 int intel_iommu_enable_pasid(struct intel_iommu *iommu, struct device *dev);
 struct dmar_domain *find_domain(struct device *dev);
@@ -806,7 +804,6 @@
 #endif /* CONFIG_INTEL_IOMMU_DEBUGFS */
 
 extern const struct attribute_group *intel_iommu_groups[];
-bool context_present(struct context_entry *context);
 struct context_entry *iommu_context_addr(struct intel_iommu *iommu, u8 bus,
 					 u8 devfn, int alloc);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/interrupt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/interrupt.h
@@ -408,7 +408,7 @@
 static inline void disable_irq_nosync_lockdep(unsigned int irq)
 {
 	disable_irq_nosync(irq);
-#ifdef CONFIG_LOCKDEP
+#if defined(CONFIG_LOCKDEP) && !defined(CONFIG_PREEMPT_RT)
 	local_irq_disable();
 #endif
 }
@@ -416,7 +416,7 @@
 static inline void disable_irq_nosync_lockdep_irqsave(unsigned int irq, unsigned long *flags)
 {
 	disable_irq_nosync(irq);
-#ifdef CONFIG_LOCKDEP
+#if defined(CONFIG_LOCKDEP) && !defined(CONFIG_PREEMPT_RT)
 	local_irq_save(*flags);
 #endif
 }
@@ -431,7 +431,7 @@
 
 static inline void enable_irq_lockdep(unsigned int irq)
 {
-#ifdef CONFIG_LOCKDEP
+#if defined(CONFIG_LOCKDEP) && !defined(CONFIG_PREEMPT_RT)
 	local_irq_enable();
 #endif
 	enable_irq(irq);
@@ -439,7 +439,7 @@
 
 static inline void enable_irq_lockdep_irqrestore(unsigned int irq, unsigned long *flags)
 {
-#ifdef CONFIG_LOCKDEP
+#if defined(CONFIG_LOCKDEP) && !defined(CONFIG_PREEMPT_RT)
 	local_irq_restore(*flags);
 #endif
 	enable_irq(irq);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/io-pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/io-pgtable.h
@@ -74,17 +74,22 @@
 	 *	to support up to 35 bits PA where the bit32, bit33 and bit34 are
 	 *	encoded in the bit9, bit4 and bit5 of the PTE respectively.
 	 *
+	 * IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT: (ARM v7s format) MediaTek IOMMUs
+	 *	extend the translation table base support up to 35 bits PA, the
+	 *	encoding format is same with IO_PGTABLE_QUIRK_ARM_MTK_EXT.
+	 *
 	 * IO_PGTABLE_QUIRK_ARM_TTBR1: (ARM LPAE format) Configure the table
 	 *	for use in the upper half of a split address space.
 	 *
 	 * IO_PGTABLE_QUIRK_ARM_OUTER_WBWA: Override the outer-cacheability
 	 *	attributes set in the TCR for a non-coherent page-table walker.
 	 */
-	#define IO_PGTABLE_QUIRK_ARM_NS		BIT(0)
-	#define IO_PGTABLE_QUIRK_NO_PERMS	BIT(1)
-	#define IO_PGTABLE_QUIRK_ARM_MTK_EXT	BIT(3)
-	#define IO_PGTABLE_QUIRK_ARM_TTBR1	BIT(5)
-	#define IO_PGTABLE_QUIRK_ARM_OUTER_WBWA	BIT(6)
+	#define IO_PGTABLE_QUIRK_ARM_NS			BIT(0)
+	#define IO_PGTABLE_QUIRK_NO_PERMS		BIT(1)
+	#define IO_PGTABLE_QUIRK_ARM_MTK_EXT		BIT(3)
+	#define IO_PGTABLE_QUIRK_ARM_MTK_TTBR_EXT	BIT(4)
+	#define IO_PGTABLE_QUIRK_ARM_TTBR1		BIT(5)
+	#define IO_PGTABLE_QUIRK_ARM_OUTER_WBWA		BIT(6)
 	unsigned long			quirks;
 	unsigned long			pgsize_bitmap;
 	unsigned int			ias;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/io_uring.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/io_uring.h
@@ -6,9 +6,9 @@
 #include <linux/xarray.h>
 
 #if defined(CONFIG_IO_URING)
-struct sock *io_uring_get_socket(struct file *file);
 void __io_uring_cancel(bool cancel_all);
 void __io_uring_free(struct task_struct *tsk);
+bool io_is_uring_fops(struct file *file);
 
 static inline void io_uring_files_cancel(void)
 {
@@ -26,10 +26,6 @@
 		__io_uring_free(tsk);
 }
 #else
-static inline struct sock *io_uring_get_socket(struct file *file)
-{
-	return NULL;
-}
 static inline void io_uring_task_cancel(void)
 {
 }
@@ -39,6 +35,10 @@
 static inline void io_uring_free(struct task_struct *tsk)
 {
 }
+static inline bool io_is_uring_fops(struct file *file)
+{
+	return false;
+}
 #endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iomap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iomap.h
@@ -330,12 +330,19 @@
   */
 #define IOMAP_DIO_OVERWRITE_ONLY	(1 << 1)
 
+/*
+ * When a page fault occurs, return a partial synchronous result and allow
+ * the caller to retry the rest of the operation after dealing with the page
+ * fault.
+ */
+#define IOMAP_DIO_PARTIAL		(1 << 2)
+
 ssize_t iomap_dio_rw(struct kiocb *iocb, struct iov_iter *iter,
 		const struct iomap_ops *ops, const struct iomap_dio_ops *dops,
-		unsigned int dio_flags);
+		unsigned int dio_flags, size_t done_before);
 struct iomap_dio *__iomap_dio_rw(struct kiocb *iocb, struct iov_iter *iter,
 		const struct iomap_ops *ops, const struct iomap_dio_ops *dops,
-		unsigned int dio_flags);
+		unsigned int dio_flags, size_t done_before);
 ssize_t iomap_dio_complete(struct iomap_dio *dio);
 int iomap_dio_iopoll(struct kiocb *kiocb, bool spin);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iommu.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iommu.h
@@ -1038,7 +1038,7 @@
 static inline struct iommu_sva *
 iommu_sva_bind_device(struct device *dev, struct mm_struct *mm, void *drvdata)
 {
-	return NULL;
+	return ERR_PTR(-ENODEV);
 }
 
 static inline void iommu_sva_unbind_device(struct iommu_sva *handle)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iopoll.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iopoll.h
@@ -53,6 +53,7 @@
 		} \
 		if (__sleep_us) \
 			usleep_range((__sleep_us >> 2) + 1, __sleep_us); \
+		cpu_relax(); \
 	} \
 	(cond) ? 0 : -ETIMEDOUT; \
 })
@@ -95,6 +96,7 @@
 		} \
 		if (__delay_us) \
 			udelay(__delay_us); \
+		cpu_relax(); \
 	} \
 	(cond) ? 0 : -ETIMEDOUT; \
 })
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ioport.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ioport.h
@@ -262,6 +262,8 @@
 #define request_muxed_region(start,n,name)	__request_region(&ioport_resource, (start), (n), (name), IORESOURCE_MUXED)
 #define __request_mem_region(start,n,name, excl) __request_region(&iomem_resource, (start), (n), (name), excl)
 #define request_mem_region(start,n,name) __request_region(&iomem_resource, (start), (n), (name), 0)
+#define request_mem_region_muxed(start, n, name) \
+	__request_region(&iomem_resource, (start), (n), (name), IORESOURCE_MUXED)
 #define request_mem_region_exclusive(start,n,name) \
 	__request_region(&iomem_resource, (start), (n), (name), IORESOURCE_EXCLUSIVE)
 #define rename_region(region, newname) do { (region)->name = (newname); } while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ioprio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ioprio.h
@@ -11,7 +11,7 @@
 /*
  * Default IO priority.
  */
-#define IOPRIO_DEFAULT	IOPRIO_PRIO_VALUE(IOPRIO_CLASS_BE, IOPRIO_BE_NORM)
+#define IOPRIO_DEFAULT	IOPRIO_PRIO_VALUE(IOPRIO_CLASS_NONE, 0)
 
 /*
  * Check that a priority value has a valid class.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/iova.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/iova.h
@@ -133,10 +133,12 @@
 	return iova >> iova_shift(iovad);
 }
 
-#if IS_ENABLED(CONFIG_IOMMU_IOVA)
+#if IS_REACHABLE(CONFIG_IOMMU_IOVA)
 int iova_cache_get(void);
 void iova_cache_put(void);
 
+unsigned long iova_rcache_range(void);
+
 void free_iova(struct iova_domain *iovad, unsigned long pfn);
 void __free_iova(struct iova_domain *iovad, struct iova *iova);
 struct iova *alloc_iova(struct iova_domain *iovad, unsigned long size,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ipc_namespace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ipc_namespace.h
@@ -10,6 +10,8 @@
 #include <linux/ns_common.h>
 #include <linux/refcount.h>
 #include <linux/rhashtable-types.h>
+#include <linux/sysctl.h>
+#include <linux/percpu_counter.h>
 
 struct user_namespace;
 
@@ -35,8 +37,8 @@
 	unsigned int	msg_ctlmax;
 	unsigned int	msg_ctlmnb;
 	unsigned int	msg_ctlmni;
-	atomic_t	msg_bytes;
-	atomic_t	msg_hdrs;
+	struct percpu_counter percpu_msg_bytes;
+	struct percpu_counter percpu_msg_hdrs;
 
 	size_t		shm_ctlmax;
 	size_t		shm_ctlall;
@@ -63,6 +65,12 @@
 	unsigned int    mq_msg_default;
 	unsigned int    mq_msgsize_default;
 
+	struct ctl_table_set	mq_set;
+	struct ctl_table_header	*mq_sysctls;
+
+	struct ctl_table_set	ipc_set;
+	struct ctl_table_header	*ipc_sysctls;
+
 	/* user_ns which owns the ipc ns */
 	struct user_namespace *user_ns;
 	struct ucounts *ucounts;
@@ -120,6 +128,9 @@
 static inline int mq_init_ns(struct ipc_namespace *ns) { return 0; }
 #endif
 
+extern struct ipc_namespace *get_ipc_ns_exported(struct ipc_namespace *ns);
+extern struct ipc_namespace *show_init_ipc_ns(void);
+
 #if defined(CONFIG_IPC_NS)
 extern struct ipc_namespace *copy_ipcs(unsigned long flags,
 	struct user_namespace *user_ns, struct ipc_namespace *ns);
@@ -131,6 +142,16 @@
 	return ns;
 }
 
+static inline struct ipc_namespace *get_ipc_ns_not_zero(struct ipc_namespace *ns)
+{
+	if (ns) {
+		if (refcount_inc_not_zero(&ns->ns.count))
+			return ns;
+	}
+
+	return NULL;
+}
+
 extern void put_ipc_ns(struct ipc_namespace *ns);
 #else
 static inline struct ipc_namespace *copy_ipcs(unsigned long flags,
@@ -147,6 +168,11 @@
 	return ns;
 }
 
+static inline struct ipc_namespace *get_ipc_ns_not_zero(struct ipc_namespace *ns)
+{
+	return ns;
+}
+
 static inline void put_ipc_ns(struct ipc_namespace *ns)
 {
 }
@@ -154,15 +180,37 @@
 
 #ifdef CONFIG_POSIX_MQUEUE_SYSCTL
 
-struct ctl_table_header;
-extern struct ctl_table_header *mq_register_sysctl_table(void);
+void retire_mq_sysctls(struct ipc_namespace *ns);
+bool setup_mq_sysctls(struct ipc_namespace *ns);
 
 #else /* CONFIG_POSIX_MQUEUE_SYSCTL */
 
-static inline struct ctl_table_header *mq_register_sysctl_table(void)
+static inline void retire_mq_sysctls(struct ipc_namespace *ns)
 {
-	return NULL;
+}
+
+static inline bool setup_mq_sysctls(struct ipc_namespace *ns)
+{
+	return true;
 }
 
 #endif /* CONFIG_POSIX_MQUEUE_SYSCTL */
+
+#ifdef CONFIG_SYSVIPC_SYSCTL
+
+bool setup_ipc_sysctls(struct ipc_namespace *ns);
+void retire_ipc_sysctls(struct ipc_namespace *ns);
+
+#else /* CONFIG_SYSVIPC_SYSCTL */
+
+static inline void retire_ipc_sysctls(struct ipc_namespace *ns)
+{
+}
+
+static inline bool setup_ipc_sysctls(struct ipc_namespace *ns)
+{
+	return true;
+}
+
+#endif /* CONFIG_SYSVIPC_SYSCTL */
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ipv6.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ipv6.h
@@ -33,6 +33,7 @@
 	__s32		accept_ra_defrtr;
 	__u32		ra_defrtr_metric;
 	__s32		accept_ra_min_hop_limit;
+	__s32		accept_ra_min_lft;
 	__s32		accept_ra_pinfo;
 	__s32		ignore_routes_with_linkdown;
 #ifdef CONFIG_IPV6_ROUTER_PREF
@@ -51,7 +52,7 @@
 	__s32		use_optimistic;
 #endif
 #ifdef CONFIG_IPV6_MROUTE
-	__s32		mc_forwarding;
+	atomic_t	mc_forwarding;
 #endif
 	__s32		disable_ipv6;
 	__s32		drop_unicast_in_l2_multicast;
@@ -132,6 +133,7 @@
 	__u16			dsthao;
 #endif
 	__u16			frag_max_size;
+	__u16			srhoff;
 
 #define IP6SKB_XFRM_TRANSFORMED	1
 #define IP6SKB_FORWARDED	2
@@ -141,6 +143,7 @@
 #define IP6SKB_HOPBYHOP        32
 #define IP6SKB_L3SLAVE         64
 #define IP6SKB_JUMBOGRAM      128
+#define IP6SKB_SEG6	      256
 };
 
 #if defined(CONFIG_NET_L3_MASTER_DEV)
@@ -282,7 +285,6 @@
 	__be32			rcv_flowinfo;
 
 	__u32			dst_cookie;
-	__u32			rx_dst_cookie;
 
 	struct ipv6_mc_socklist	__rcu *ipv6_mc_list;
 	struct ipv6_ac_socklist	*ipv6_ac_list;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irq.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irq.h
@@ -709,10 +709,11 @@
 extern struct irq_chip dummy_irq_chip;
 
 extern void
-irq_set_chip_and_handler_name(unsigned int irq, struct irq_chip *chip,
+irq_set_chip_and_handler_name(unsigned int irq, const struct irq_chip *chip,
 			      irq_flow_handler_t handle, const char *name);
 
-static inline void irq_set_chip_and_handler(unsigned int irq, struct irq_chip *chip,
+static inline void irq_set_chip_and_handler(unsigned int irq,
+					    const struct irq_chip *chip,
 					    irq_flow_handler_t handle)
 {
 	irq_set_chip_and_handler_name(irq, chip, handle, NULL);
@@ -802,7 +803,7 @@
 }
 
 /* Set/get chip/data for an IRQ: */
-extern int irq_set_chip(unsigned int irq, struct irq_chip *chip);
+extern int irq_set_chip(unsigned int irq, const struct irq_chip *chip);
 extern int irq_set_handler_data(unsigned int irq, void *data);
 extern int irq_set_chip_data(unsigned int irq, void *data);
 extern int irq_set_irq_type(unsigned int irq, unsigned int type);
@@ -875,16 +876,22 @@
 	return irq_common_data_get_node(d->common);
 }
 
-static inline struct cpumask *irq_get_affinity_mask(int irq)
+static inline struct cpumask *irq_data_get_affinity_mask(struct irq_data *d)
 {
-	struct irq_data *d = irq_get_irq_data(irq);
+	return d->common->affinity;
+}
 
-	return d ? d->common->affinity : NULL;
+static inline void irq_data_update_affinity(struct irq_data *d,
+					    const struct cpumask *m)
+{
+	cpumask_copy(d->common->affinity, m);
 }
 
-static inline struct cpumask *irq_data_get_affinity_mask(struct irq_data *d)
+static inline struct cpumask *irq_get_affinity_mask(int irq)
 {
-	return d->common->affinity;
+	struct irq_data *d = irq_get_irq_data(irq);
+
+	return d ? irq_data_get_affinity_mask(d) : NULL;
 }
 
 #ifdef CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK
@@ -906,7 +913,7 @@
 static inline
 struct cpumask *irq_data_get_effective_affinity_mask(struct irq_data *d)
 {
-	return d->common->affinity;
+	return irq_data_get_affinity_mask(d);
 }
 #endif
 
@@ -1102,6 +1109,21 @@
 	struct irq_chip_generic	*gc[];
 };
 
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+/**
+ * struct irqc_init_remove_funps - Stores function pointers for irqc init
+ * and remove APIs. Used when the irqchip driver is to be used as a module.
+ * @irqchip_initp:	Function pointer for init/entry point of a irqchip driver.
+ * @irqchip_removep:Function pointer for irqchip driver remove function.
+ */
+struct irqc_init_remove_funps {
+	int (*irqchip_initp)(struct device_node *irqc,
+			     struct device_node *parent);
+	int (*irqchip_removep)(struct device_node *irqc,
+			       struct device_node *parent);
+};
+#endif
+
 /* Generic chip callback functions */
 void irq_gc_noop(struct irq_data *d);
 void irq_gc_mask_disable_reg(struct irq_data *d);
@@ -1254,7 +1276,11 @@
  * Returns 0 on success, or -EBUSY if an IRQ handler has already been
  * registered.
  */
+#ifndef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
 int __init set_handle_irq(void (*handle_irq)(struct pt_regs *));
+#else
+int set_handle_irq(void (*handle_irq)(struct pt_regs *));
+#endif
 
 /*
  * Allows interrupt handlers to find the irqchip that's been registered as the
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irq_work.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irq_work.h
@@ -58,6 +58,9 @@
 void irq_work_run(void);
 bool irq_work_needs_cpu(void);
 void irq_work_single(void *arg);
+
+void arch_irq_work_raise(void);
+
 #else
 static inline bool irq_work_needs_cpu(void) { return false; }
 static inline void irq_work_run(void) { }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irqchip.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irqchip.h
@@ -29,12 +29,16 @@
 #define IRQCHIP_DECLARE(name, compat, fn) OF_DECLARE_2(irqchip, name, compat, fn)
 
 extern int platform_irqchip_probe(struct platform_device *pdev);
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+extern int platform_irqchip_remove(struct platform_device *pdev);
+#endif
 
 #define IRQCHIP_PLATFORM_DRIVER_BEGIN(drv_name) \
 static const struct of_device_id drv_name##_irqchip_match_table[] = {
 
 #define IRQCHIP_MATCH(compat, fn) { .compatible = compat, .data = fn },
 
+#ifndef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
 #define IRQCHIP_PLATFORM_DRIVER_END(drv_name)				\
 	{},								\
 };									\
@@ -49,6 +53,23 @@
 	},								\
 };									\
 builtin_platform_driver(drv_name##_driver)
+#else
+#define IRQCHIP_PLATFORM_DRIVER_END(drv_name)				\
+	{},								\
+};									\
+MODULE_DEVICE_TABLE(of, drv_name##_irqchip_match_table);		\
+static struct platform_driver drv_name##_driver = {		\
+	.probe  = platform_irqchip_probe,				\
+	.remove = platform_irqchip_remove,              \
+	.driver = {							\
+		.name = #drv_name,					\
+		.owner = THIS_MODULE,					\
+		.of_match_table = drv_name##_irqchip_match_table,	\
+		.suppress_bind_attrs = true,				\
+	},								\
+};									\
+builtin_platform_driver(drv_name##_driver)
+#endif
 
 /*
  * This macro must be used by the different irqchip drivers to declare
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irqchip/arm-gic-v4.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irqchip/arm-gic-v4.h
@@ -58,10 +58,12 @@
 				bool	enabled;
 				bool	group;
 			}			sgi_config[16];
-			atomic_t vmapp_count;
 		};
 	};
 
+	/* Track the VPE being mapped */
+	atomic_t vmapp_count;
+
 	/*
 	 * Ensures mutual exclusion between affinity setting of the
 	 * vPE and vLPI operations using vpe->col_idx.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irqchip/arm-gic.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irqchip/arm-gic.h
@@ -134,6 +134,9 @@
 
 void gic_cascade_irq(unsigned int gic_nr, unsigned int irq);
 int gic_cpu_if_down(unsigned int gic_nr);
+void gic_ipi_send_mask(struct irq_data *d, const struct cpumask *mask);
+
+void gic_set_cpu(unsigned int cpu, unsigned int irq);
 void gic_cpu_save(struct gic_chip_data *gic);
 void gic_cpu_restore(struct gic_chip_data *gic);
 void gic_dist_save(struct gic_chip_data *gic);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irqdomain.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irqdomain.h
@@ -147,6 +147,8 @@
  * @gc: Pointer to a list of generic chips. There is a helper function for
  *      setting up one or more generic chips for interrupt controllers
  *      drivers using the generic chip library which uses this pointer.
+ * @dev: Pointer to a device that the domain represent, and that will be
+ *       used for power management purposes.
  * @parent: Pointer to parent irq_domain to support hierarchy irq_domains
  *
  * Revmap data, used internally by irq_domain
@@ -167,6 +169,7 @@
 	struct fwnode_handle *fwnode;
 	enum irq_domain_bus_token bus_token;
 	struct irq_domain_chip_generic *gc;
+	struct device *dev;
 #ifdef	CONFIG_IRQ_DOMAIN_HIERARCHY
 	struct irq_domain *parent;
 #endif
@@ -222,6 +225,13 @@
 	return to_of_node(d->fwnode);
 }
 
+static inline void irq_domain_set_pm_device(struct irq_domain *d,
+					    struct device *dev)
+{
+	if (d)
+		d->dev = dev;
+}
+
 #ifdef CONFIG_IRQ_DOMAIN
 struct fwnode_handle *__irq_domain_alloc_fwnode(unsigned int type, int id,
 						const char *name, phys_addr_t *pa);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/irqflags.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/irqflags.h
@@ -20,13 +20,13 @@
 #ifdef CONFIG_PROVE_LOCKING
   extern void lockdep_softirqs_on(unsigned long ip);
   extern void lockdep_softirqs_off(unsigned long ip);
-  extern void lockdep_hardirqs_on_prepare(unsigned long ip);
+  extern void lockdep_hardirqs_on_prepare(void);
   extern void lockdep_hardirqs_on(unsigned long ip);
   extern void lockdep_hardirqs_off(unsigned long ip);
 #else
   static inline void lockdep_softirqs_on(unsigned long ip) { }
   static inline void lockdep_softirqs_off(unsigned long ip) { }
-  static inline void lockdep_hardirqs_on_prepare(unsigned long ip) { }
+  static inline void lockdep_hardirqs_on_prepare(void) { }
   static inline void lockdep_hardirqs_on(unsigned long ip) { }
   static inline void lockdep_hardirqs_off(unsigned long ip) { }
 #endif
@@ -133,7 +133,7 @@
 # define lockdep_softirq_enter()		do { } while (0)
 # define lockdep_softirq_exit()			do { } while (0)
 # define lockdep_hrtimer_enter(__hrtimer)	false
-# define lockdep_hrtimer_exit(__context)	do { } while (0)
+# define lockdep_hrtimer_exit(__context)	do { (void)(__context); } while (0)
 # define lockdep_posixtimer_enter()		do { } while (0)
 # define lockdep_posixtimer_exit()		do { } while (0)
 # define lockdep_irq_work_enter(__work)		do { } while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/jbd2.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/jbd2.h
@@ -58,10 +58,10 @@
 void __jbd2_debug(int level, const char *file, const char *func,
 		  unsigned int line, const char *fmt, ...);
 
-#define jbd_debug(n, fmt, a...) \
+#define jbd2_debug(n, fmt, a...) \
 	__jbd2_debug((n), __FILE__, __func__, __LINE__, (fmt), ##a)
 #else
-#define jbd_debug(n, fmt, a...)  no_printk(fmt, ##a)
+#define jbd2_debug(n, fmt, a...)  no_printk(fmt, ##a)
 #endif
 
 extern void *jbd2_alloc(size_t size, gfp_t flags);
@@ -554,9 +554,6 @@
  *    ->j_list_lock
  *
  *    j_state_lock
- *    ->t_handle_lock
- *
- *    j_state_lock
  *    ->j_list_lock			(journal_unmap_buffer)
  *
  */
@@ -594,7 +591,7 @@
 	 */
 	unsigned long		t_log_start;
 
-	/* 
+	/*
 	 * Number of buffers on the t_buffers list [j_list_lock, no locks
 	 * needed for jbd2 thread]
 	 */
@@ -627,12 +624,6 @@
 	struct journal_head	*t_checkpoint_list;
 
 	/*
-	 * Doubly-linked circular list of all buffers submitted for IO while
-	 * checkpointing. [j_list_lock]
-	 */
-	struct journal_head	*t_checkpoint_io_list;
-
-	/*
 	 * Doubly-linked circular list of metadata buffers being
 	 * shadowed by log IO.  The IO buffers on the iobuf list and
 	 * the shadow buffers on this list match each other one for
@@ -1295,7 +1286,7 @@
 	 * Clean-up after fast commit or full commit. JBD2 calls this function
 	 * after every commit operation.
 	 */
-	void (*j_fc_cleanup_callback)(struct journal_s *journal, int);
+	void (*j_fc_cleanup_callback)(struct journal_s *journal, int full, tid_t tid);
 
 	/**
 	 * @j_fc_replay_callback:
@@ -1447,6 +1438,7 @@
 void __jbd2_journal_clean_checkpoint_list(journal_t *journal, bool destroy);
 unsigned long jbd2_journal_shrink_checkpoint_list(journal_t *journal, unsigned long *nr_to_scan);
 int __jbd2_journal_remove_checkpoint(struct journal_head *);
+int jbd2_journal_try_remove_checkpoint(struct journal_head *jh);
 void jbd2_journal_destroy_checkpoint(journal_t *journal);
 void __jbd2_journal_insert_checkpoint(struct journal_head *, transaction_t *);
 
@@ -1543,6 +1535,8 @@
 extern void	 jbd2_journal_lock_updates (journal_t *);
 extern void	 jbd2_journal_unlock_updates (journal_t *);
 
+void jbd2_journal_wait_updates(journal_t *);
+
 extern journal_t * jbd2_journal_init_dev(struct block_device *bdev,
 				struct block_device *fs_dev,
 				unsigned long long start, int len, int bsize);
@@ -1675,11 +1669,6 @@
 int jbd2_fc_wait_bufs(journal_t *journal, int num_blks);
 int jbd2_fc_release_bufs(journal_t *journal);
 
-static inline int jbd2_journal_get_max_txn_bufs(journal_t *journal)
-{
-	return (journal->j_total_len - journal->j_fc_wbufsize) / 4;
-}
-
 /*
  * is_journal_abort
  *
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/jiffies.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/jiffies.h
@@ -349,7 +349,7 @@
  * - all other values are converted to jiffies by either multiplying
  *   the input value by a factor or dividing it with a factor and
  *   handling any 32-bit overflows.
- *   for the details see __msecs_to_jiffies()
+ *   for the details see _msecs_to_jiffies()
  *
  * msecs_to_jiffies() checks for the passed in value being a constant
  * via __builtin_constant_p() allowing gcc to eliminate most of the
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/jump_label.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/jump_label.h
@@ -261,9 +261,9 @@
 #include <linux/atomic.h>
 #include <linux/bug.h>
 
-static inline int static_key_count(struct static_key *key)
+static __always_inline int static_key_count(struct static_key *key)
 {
-	return atomic_read(&key->enabled);
+	return arch_atomic_read(&key->enabled);
 }
 
 static __always_inline void jump_label_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kallsyms.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kallsyms.h
@@ -66,19 +66,19 @@
 
 	preempt_disable();
 	mod = __module_address((unsigned long)ptr);
-	preempt_enable();
 
 	if (mod)
 		ptr = dereference_module_function_descriptor(mod, ptr);
+	preempt_enable();
 #endif
 	return ptr;
 }
 
+#ifdef CONFIG_KALLSYMS
 int kallsyms_on_each_symbol(int (*fn)(void *, const char *, struct module *,
 				      unsigned long),
 			    void *data);
 
-#ifdef CONFIG_KALLSYMS
 /* Lookup the address for a symbol. Returns 0 if not found. */
 unsigned long kallsyms_lookup_name(const char *name);
 
@@ -172,6 +172,11 @@
 	return false;
 }
 
+static inline int kallsyms_on_each_symbol(int (*fn)(void *, const char *, struct module *,
+					  unsigned long), void *data)
+{
+	return -EOPNOTSUPP;
+}
 #endif /*CONFIG_KALLSYMS*/
 
 static inline void print_ip_sym(const char *loglvl, unsigned long ip)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kasan.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kasan.h
@@ -461,20 +461,20 @@
  * allocations with real shadow memory. With KASAN vmalloc, the special
  * case is unnecessary, as the work is handled in the generic case.
  */
-int kasan_module_alloc(void *addr, size_t size);
+int kasan_module_alloc(void *addr, size_t size, gfp_t gfp_mask);
 void kasan_free_shadow(const struct vm_struct *vm);
 
 #else /* (CONFIG_KASAN_GENERIC || CONFIG_KASAN_SW_TAGS) && !CONFIG_KASAN_VMALLOC */
 
-static inline int kasan_module_alloc(void *addr, size_t size) { return 0; }
+static inline int kasan_module_alloc(void *addr, size_t size, gfp_t gfp_mask) { return 0; }
 static inline void kasan_free_shadow(const struct vm_struct *vm) {}
 
 #endif /* (CONFIG_KASAN_GENERIC || CONFIG_KASAN_SW_TAGS) && !CONFIG_KASAN_VMALLOC */
 
-#ifdef CONFIG_KASAN_INLINE
+#if defined(CONFIG_KASAN_GENERIC) || defined(CONFIG_KASAN_SW_TAGS)
 void kasan_non_canonical_hook(unsigned long addr);
-#else /* CONFIG_KASAN_INLINE */
+#else /* CONFIG_KASAN_GENERIC || CONFIG_KASAN_SW_TAGS */
 static inline void kasan_non_canonical_hook(unsigned long addr) { }
-#endif /* CONFIG_KASAN_INLINE */
+#endif /* CONFIG_KASAN_GENERIC || CONFIG_KASAN_SW_TAGS */
 
 #endif /* LINUX_KASAN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kcov.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kcov.h
@@ -21,6 +21,8 @@
 	KCOV_MODE_TRACE_PC = 2,
 	/* Collecting comparison operands mode. */
 	KCOV_MODE_TRACE_CMP = 3,
+	/* The process owns a KCOV remote reference. */
+	KCOV_MODE_REMOTE = 4,
 };
 
 #define KCOV_IN_CTXSW	(1 << 30)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kernel.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kernel.h
@@ -277,7 +277,7 @@
 	return buf;
 }
 
-extern int hex_to_bin(char ch);
+extern int hex_to_bin(unsigned char ch);
 extern int __must_check hex2bin(u8 *dst, const char *src, size_t count);
 extern char *bin2hex(char *dst, const void *src, size_t count);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kernel_stat.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kernel_stat.h
@@ -72,7 +72,7 @@
 /*
  * Number of interrupts per cpu, since bootup
  */
-static inline unsigned int kstat_cpu_irqs_sum(unsigned int cpu)
+static inline unsigned long kstat_cpu_irqs_sum(unsigned int cpu)
 {
 	return kstat_cpu(cpu).irqs_sum;
 }
@@ -102,6 +102,7 @@
 				      enum cpu_usage_stat);
 extern void account_steal_time(u64);
 extern void account_idle_time(u64);
+extern u64 get_idle_time(struct kernel_cpustat *kcs, int cpu);
 
 #ifdef CONFIG_VIRT_CPU_ACCOUNTING_NATIVE
 static inline void account_process_tick(struct task_struct *tsk, int user)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kexec.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kexec.h
@@ -19,6 +19,7 @@
 #include <asm/io.h>
 
 #include <uapi/linux/kexec.h>
+#include <linux/verification.h>
 
 #ifdef CONFIG_KEXEC_CORE
 #include <linux/list.h>
@@ -187,14 +188,6 @@
 int arch_kexec_kernel_image_probe(struct kimage *image, void *buf,
 				  unsigned long buf_len);
 void *arch_kexec_kernel_image_load(struct kimage *image);
-int arch_kexec_apply_relocations_add(struct purgatory_info *pi,
-				     Elf_Shdr *section,
-				     const Elf_Shdr *relsec,
-				     const Elf_Shdr *symtab);
-int arch_kexec_apply_relocations(struct purgatory_info *pi,
-				 Elf_Shdr *section,
-				 const Elf_Shdr *relsec,
-				 const Elf_Shdr *symtab);
 int arch_kimage_file_post_load_cleanup(struct kimage *image);
 #ifdef CONFIG_KEXEC_SIG
 int arch_kexec_kernel_verify_sig(struct kimage *image, void *buf,
@@ -202,6 +195,12 @@
 #endif
 int arch_kexec_locate_mem_hole(struct kexec_buf *kbuf);
 
+#ifdef CONFIG_KEXEC_SIG
+#ifdef CONFIG_SIGNED_PE_FILE_VERIFICATION
+int kexec_kernel_verify_pe_sig(const char *kernel, unsigned long kernel_len);
+#endif
+#endif
+
 extern int kexec_add_buffer(struct kexec_buf *kbuf);
 int kexec_locate_mem_hole(struct kexec_buf *kbuf);
 
@@ -223,6 +222,44 @@
 				   unsigned long long mend);
 extern int crash_prepare_elf64_headers(struct crash_mem *mem, int kernel_map,
 				       void **addr, unsigned long *sz);
+
+#ifndef arch_kexec_apply_relocations_add
+/*
+ * arch_kexec_apply_relocations_add - apply relocations of type RELA
+ * @pi:		Purgatory to be relocated.
+ * @section:	Section relocations applying to.
+ * @relsec:	Section containing RELAs.
+ * @symtab:	Corresponding symtab.
+ *
+ * Return: 0 on success, negative errno on error.
+ */
+static inline int
+arch_kexec_apply_relocations_add(struct purgatory_info *pi, Elf_Shdr *section,
+				 const Elf_Shdr *relsec, const Elf_Shdr *symtab)
+{
+	pr_err("RELA relocation unsupported.\n");
+	return -ENOEXEC;
+}
+#endif
+
+#ifndef arch_kexec_apply_relocations
+/*
+ * arch_kexec_apply_relocations - apply relocations of type REL
+ * @pi:		Purgatory to be relocated.
+ * @section:	Section relocations applying to.
+ * @relsec:	Section containing RELs.
+ * @symtab:	Corresponding symtab.
+ *
+ * Return: 0 on success, negative errno on error.
+ */
+static inline int
+arch_kexec_apply_relocations(struct purgatory_info *pi, Elf_Shdr *section,
+			     const Elf_Shdr *relsec, const Elf_Shdr *symtab)
+{
+	pr_err("REL relocation unsupported.\n");
+	return -ENOEXEC;
+}
+#endif
 #endif /* CONFIG_KEXEC_FILE */
 
 #ifdef CONFIG_KEXEC_ELF
@@ -360,8 +397,8 @@
 extern bool kexec_in_progress;
 
 int crash_shrink_memory(unsigned long new_size);
-size_t crash_get_memory_size(void);
 void crash_free_reserved_phys_range(unsigned long begin, unsigned long end);
+ssize_t crash_get_memory_size(void);
 
 void arch_kexec_protect_crashkres(void);
 void arch_kexec_unprotect_crashkres(void);
@@ -422,6 +459,12 @@
 #define kexec_in_progress false
 #endif /* CONFIG_KEXEC_CORE */
 
+#ifdef CONFIG_KEXEC_SIG
+void set_kexec_sig_enforced(void);
+#else
+static inline void set_kexec_sig_enforced(void) {}
+#endif
+
 #endif /* !defined(__ASSEBMLY__) */
 
 #endif /* LINUX_KEXEC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/key-type.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/key-type.h
@@ -73,6 +73,7 @@
 
 	unsigned int flags;
 #define KEY_TYPE_NET_DOMAIN	0x00000001 /* Keys of this type have a net namespace domain */
+#define KEY_TYPE_INSTANT_REAP	0x00000002 /* Keys of this type don't have a delay after expiring */
 
 	/* vet a description */
 	int (*vet_description)(const char *description);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kfence.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kfence.h
@@ -14,6 +14,9 @@
 
 #ifdef CONFIG_KFENCE
 
+#include <linux/atomic.h>
+#include <linux/static_key.h>
+
 /*
  * We allocate an even number of pages, as it simplifies calculations to map
  * address to metadata indices; effectively, the very first page serves as an
@@ -22,13 +25,8 @@
 #define KFENCE_POOL_SIZE ((CONFIG_KFENCE_NUM_OBJECTS + 1) * 2 * PAGE_SIZE)
 extern char *__kfence_pool;
 
-#ifdef CONFIG_KFENCE_STATIC_KEYS
-#include <linux/static_key.h>
 DECLARE_STATIC_KEY_FALSE(kfence_allocation_key);
-#else
-#include <linux/atomic.h>
 extern atomic_t kfence_allocation_gate;
-#endif
 
 /**
  * is_kfence_address() - check if an address belongs to KFENCE pool
@@ -116,13 +114,16 @@
  */
 static __always_inline void *kfence_alloc(struct kmem_cache *s, size_t size, gfp_t flags)
 {
-#ifdef CONFIG_KFENCE_STATIC_KEYS
-	if (static_branch_unlikely(&kfence_allocation_key))
+#if defined(CONFIG_KFENCE_STATIC_KEYS) || CONFIG_KFENCE_SAMPLE_INTERVAL == 0
+	if (!static_branch_unlikely(&kfence_allocation_key))
+		return NULL;
 #else
-	if (unlikely(!atomic_read(&kfence_allocation_gate)))
+	if (!static_branch_likely(&kfence_allocation_key))
+		return NULL;
 #endif
-		return __kfence_alloc(s, size, flags);
-	return NULL;
+	if (likely(atomic_read(&kfence_allocation_gate)))
+		return NULL;
+	return __kfence_alloc(s, size, flags);
 }
 
 /**
@@ -201,6 +202,22 @@
  */
 bool __must_check kfence_handle_page_fault(unsigned long addr, bool is_write, struct pt_regs *regs);
 
+#ifdef CONFIG_PRINTK
+struct kmem_obj_info;
+/**
+ * __kfence_obj_info() - fill kmem_obj_info struct
+ * @kpp: kmem_obj_info to be filled
+ * @object: the object
+ *
+ * Return:
+ * * false - not a KFENCE object
+ * * true - a KFENCE object, filled @kpp
+ *
+ * Copies information to @kpp for KFENCE objects.
+ */
+bool __kfence_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page);
+#endif
+
 #else /* CONFIG_KFENCE */
 
 static inline bool is_kfence_address(const void *addr) { return false; }
@@ -218,6 +235,14 @@
 	return false;
 }
 
+#ifdef CONFIG_PRINTK
+struct kmem_obj_info;
+static inline bool __kfence_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
+{
+	return false;
+}
+#endif
+
 #endif
 
 #endif /* _LINUX_KFENCE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kfifo.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kfifo.h
@@ -688,7 +688,7 @@
  * writer, you don't need extra locking to use these macro.
  */
 #define	kfifo_to_user(fifo, to, len, copied) \
-__kfifo_uint_must_check_helper( \
+__kfifo_int_must_check_helper( \
 ({ \
 	typeof((fifo) + 1) __tmp = (fifo); \
 	void __user *__to = (to); \
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kobject.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kobject.h
@@ -116,7 +116,7 @@
 extern const void *kobject_namespace(struct kobject *kobj);
 extern void kobject_get_ownership(struct kobject *kobj,
 				  kuid_t *uid, kgid_t *gid);
-extern char *kobject_get_path(struct kobject *kobj, gfp_t flag);
+extern char *kobject_get_path(const struct kobject *kobj, gfp_t flag);
 
 /**
  * kobject_has_children - Returns whether a kobject has children.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kprobes.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kprobes.h
@@ -139,7 +139,7 @@
  *
  */
 struct kretprobe_holder {
-	struct kretprobe	*rp;
+	struct kretprobe __rcu *rp;
 	refcount_t		ref;
 };
 
@@ -154,6 +154,8 @@
 	struct kretprobe_holder *rph;
 };
 
+#define KRETPROBE_MAX_DATA_SIZE	4096
+
 struct kretprobe_instance {
 	union {
 		struct freelist_node freelist;
@@ -197,15 +199,23 @@
 				   struct pt_regs *regs);
 extern int arch_trampoline_kprobe(struct kprobe *p);
 
+void __kretprobe_trampoline(void);
+/*
+ * Since some architecture uses structured function pointer,
+ * use dereference_function_descriptor() to get real function address.
+ */
+static nokprobe_inline void *kretprobe_trampoline_addr(void)
+{
+	return dereference_kernel_function_descriptor(__kretprobe_trampoline);
+}
+
 /* If the trampoline handler called from a kprobe, use this version */
 unsigned long __kretprobe_trampoline_handler(struct pt_regs *regs,
-				void *trampoline_address,
-				void *frame_pointer);
+					     void *frame_pointer);
 
 static nokprobe_inline
 unsigned long kretprobe_trampoline_handler(struct pt_regs *regs,
-				void *trampoline_address,
-				void *frame_pointer)
+					   void *frame_pointer)
 {
 	unsigned long ret;
 	/*
@@ -214,7 +224,7 @@
 	 * be running at this point.
 	 */
 	kprobe_busy_begin();
-	ret = __kretprobe_trampoline_handler(regs, trampoline_address, frame_pointer);
+	ret = __kretprobe_trampoline_handler(regs, frame_pointer);
 	kprobe_busy_end();
 
 	return ret;
@@ -222,10 +232,7 @@
 
 static nokprobe_inline struct kretprobe *get_kretprobe(struct kretprobe_instance *ri)
 {
-	RCU_LOCKDEP_WARN(!rcu_read_lock_any_held(),
-		"Kretprobe is accessed from instance under preemptive context");
-
-	return READ_ONCE(ri->rph->rp);
+	return rcu_dereference_check(ri->rph->rp, rcu_read_lock_any_held());
 }
 
 #else /* CONFIG_KRETPROBES */
@@ -347,6 +354,8 @@
 					     size_t *length, loff_t *ppos);
 #endif
 extern void wait_for_kprobe_optimizer(void);
+bool optprobe_queued_unopt(struct optimized_kprobe *op);
+bool kprobe_disarmed(struct kprobe *p);
 #else
 static inline void wait_for_kprobe_optimizer(void) { }
 #endif /* CONFIG_OPTPROBES */
@@ -501,6 +510,28 @@
 }
 #endif
 
+#ifdef CONFIG_KRETPROBES
+static nokprobe_inline bool is_kretprobe_trampoline(unsigned long addr)
+{
+	return (void *)addr == kretprobe_trampoline_addr();
+}
+
+unsigned long kretprobe_find_ret_addr(struct task_struct *tsk, void *fp,
+				      struct llist_node **cur);
+#else
+static nokprobe_inline bool is_kretprobe_trampoline(unsigned long addr)
+{
+	return false;
+}
+
+static nokprobe_inline
+unsigned long kretprobe_find_ret_addr(struct task_struct *tsk, void *fp,
+				      struct llist_node **cur)
+{
+	return 0;
+}
+#endif
+
 /* Returns true if kprobes handled the fault */
 static nokprobe_inline bool kprobe_page_fault(struct pt_regs *regs,
 					      unsigned int trap)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kthread.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kthread.h
@@ -56,6 +56,31 @@
 	__k;								   \
 })
 
+/**
+ * kthread_run_on_cpu - create and wake a cpu bound thread.
+ * @threadfn: the function to run until signal_pending(current).
+ * @data: data ptr for @threadfn.
+ * @cpu: The cpu on which the thread should be bound,
+ * @namefmt: printf-style name for the thread. Format is restricted
+ *	     to "name.*%u". Code fills in cpu number.
+ *
+ * Description: Convenient wrapper for kthread_create_on_cpu()
+ * followed by wake_up_process().  Returns the kthread or
+ * ERR_PTR(-ENOMEM).
+ */
+static inline struct task_struct *
+kthread_run_on_cpu(int (*threadfn)(void *data), void *data,
+			unsigned int cpu, const char *namefmt)
+{
+	struct task_struct *p;
+
+	p = kthread_create_on_cpu(threadfn, data, cpu, namefmt);
+	if (!IS_ERR(p))
+		wake_up_process(p);
+
+	return p;
+}
+
 void free_kthread_struct(struct task_struct *k);
 void kthread_bind(struct task_struct *k, unsigned int cpu);
 void kthread_bind_mask(struct task_struct *k, const struct cpumask *mask);
@@ -70,6 +95,7 @@
 int kthread_park(struct task_struct *k);
 void kthread_unpark(struct task_struct *k);
 void kthread_parkme(void);
+void kthread_exit(long result) __noreturn;
 
 int kthreadd(void *unused);
 extern struct task_struct *kthreadd_task;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/kvm_host.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/kvm_host.h
@@ -15,6 +15,8 @@
 #include <linux/minmax.h>
 #include <linux/mm.h>
 #include <linux/mmu_notifier.h>
+#include <linux/ftrace.h>
+#include <linux/instrumentation.h>
 #include <linux/preempt.h>
 #include <linux/msi.h>
 #include <linux/slab.h>
@@ -363,8 +365,11 @@
 	int last_used_slot;
 };
 
-/* must be called with irqs disabled */
-static __always_inline void guest_enter_irqoff(void)
+/*
+ * Start accounting time towards a guest.
+ * Must be called before entering guest context.
+ */
+static __always_inline void guest_timing_enter_irqoff(void)
 {
 	/*
 	 * This is running in ioctl context so its safe to assume that it's the
@@ -373,7 +378,18 @@
 	instrumentation_begin();
 	vtime_account_guest_enter();
 	instrumentation_end();
+}
 
+/*
+ * Enter guest context and enter an RCU extended quiescent state.
+ *
+ * Between guest_context_enter_irqoff() and guest_context_exit_irqoff() it is
+ * unsafe to use any code which may directly or indirectly use RCU, tracing
+ * (including IRQ flag tracing), or lockdep. All code in this period must be
+ * non-instrumentable.
+ */
+static __always_inline void guest_context_enter_irqoff(void)
+{
 	/*
 	 * KVM does not hold any references to rcu protected data when it
 	 * switches CPU into a guest mode. In fact switching to a guest mode
@@ -389,16 +405,79 @@
 	}
 }
 
-static __always_inline void guest_exit_irqoff(void)
+/*
+ * Deprecated. Architectures should move to guest_timing_enter_irqoff() and
+ * guest_state_enter_irqoff().
+ */
+static __always_inline void guest_enter_irqoff(void)
+{
+	guest_timing_enter_irqoff();
+	guest_context_enter_irqoff();
+}
+
+/**
+ * guest_state_enter_irqoff - Fixup state when entering a guest
+ *
+ * Entry to a guest will enable interrupts, but the kernel state is interrupts
+ * disabled when this is invoked. Also tell RCU about it.
+ *
+ * 1) Trace interrupts on state
+ * 2) Invoke context tracking if enabled to adjust RCU state
+ * 3) Tell lockdep that interrupts are enabled
+ *
+ * Invoked from architecture specific code before entering a guest.
+ * Must be called with interrupts disabled and the caller must be
+ * non-instrumentable.
+ * The caller has to invoke guest_timing_enter_irqoff() before this.
+ *
+ * Note: this is analogous to exit_to_user_mode().
+ */
+static __always_inline void guest_state_enter_irqoff(void)
+{
+	instrumentation_begin();
+	trace_hardirqs_on_prepare();
+	lockdep_hardirqs_on_prepare();
+	instrumentation_end();
+
+	guest_context_enter_irqoff();
+	lockdep_hardirqs_on(CALLER_ADDR0);
+}
+
+/*
+ * Exit guest context and exit an RCU extended quiescent state.
+ *
+ * Between guest_context_enter_irqoff() and guest_context_exit_irqoff() it is
+ * unsafe to use any code which may directly or indirectly use RCU, tracing
+ * (including IRQ flag tracing), or lockdep. All code in this period must be
+ * non-instrumentable.
+ */
+static __always_inline void guest_context_exit_irqoff(void)
 {
 	context_tracking_guest_exit();
+}
 
+/*
+ * Stop accounting time towards a guest.
+ * Must be called after exiting guest context.
+ */
+static __always_inline void guest_timing_exit_irqoff(void)
+{
 	instrumentation_begin();
 	/* Flush the guest cputime we spent on the guest */
 	vtime_account_guest_exit();
 	instrumentation_end();
 }
 
+/*
+ * Deprecated. Architectures should move to guest_state_exit_irqoff() and
+ * guest_timing_exit_irqoff().
+ */
+static __always_inline void guest_exit_irqoff(void)
+{
+	guest_context_exit_irqoff();
+	guest_timing_exit_irqoff();
+}
+
 static inline void guest_exit(void)
 {
 	unsigned long flags;
@@ -408,6 +487,33 @@
 	local_irq_restore(flags);
 }
 
+/**
+ * guest_state_exit_irqoff - Establish state when returning from guest mode
+ *
+ * Entry from a guest disables interrupts, but guest mode is traced as
+ * interrupts enabled. Also with NO_HZ_FULL RCU might be idle.
+ *
+ * 1) Tell lockdep that interrupts are disabled
+ * 2) Invoke context tracking if enabled to reactivate RCU
+ * 3) Trace interrupts off state
+ *
+ * Invoked from architecture specific code after exiting a guest.
+ * Must be invoked with interrupts disabled and the caller must be
+ * non-instrumentable.
+ * The caller has to invoke guest_timing_exit_irqoff() after this.
+ *
+ * Note: this is analogous to enter_from_user_mode().
+ */
+static __always_inline void guest_state_exit_irqoff(void)
+{
+	lockdep_hardirqs_off(CALLER_ADDR0);
+	guest_context_exit_irqoff();
+
+	instrumentation_begin();
+	trace_hardirqs_off_finish();
+	instrumentation_end();
+}
+
 static inline int kvm_vcpu_exiting_guest_mode(struct kvm_vcpu *vcpu)
 {
 	/*
@@ -690,6 +796,15 @@
 static inline struct kvm_vcpu *kvm_get_vcpu(struct kvm *kvm, int i)
 {
 	int num_vcpus = atomic_read(&kvm->online_vcpus);
+
+	/*
+	 * Explicitly verify the target vCPU is online, as the anti-speculation
+	 * logic only limits the CPU's ability to speculate, e.g. given a "bad"
+	 * index, clamping the index to 0 would return vCPU0, not NULL.
+	 */
+	if (i >= num_vcpus)
+		return NULL;
+
 	i = array_index_nospec(i, num_vcpus);
 
 	/* Pairs with smp_wmb() in kvm_vm_ioctl_create_vcpu.  */
@@ -1018,6 +1133,8 @@
 			    struct kvm_enable_cap *cap);
 long kvm_arch_vm_ioctl(struct file *filp,
 		       unsigned int ioctl, unsigned long arg);
+long kvm_arch_vm_compat_ioctl(struct file *filp, unsigned int ioctl,
+			      unsigned long arg);
 
 int kvm_arch_vcpu_ioctl_get_fpu(struct kvm_vcpu *vcpu, struct kvm_fpu *fpu);
 int kvm_arch_vcpu_ioctl_set_fpu(struct kvm_vcpu *vcpu, struct kvm_fpu *fpu);
@@ -1082,10 +1199,17 @@
 {
 	return kzalloc(sizeof(struct kvm), GFP_KERNEL);
 }
+#endif
 
+static inline void __kvm_arch_free_vm(struct kvm *kvm)
+{
+	kvfree(kvm);
+}
+
+#ifndef __KVM_HAVE_ARCH_VM_FREE
 static inline void kvm_arch_free_vm(struct kvm *kvm)
 {
-	kfree(kvm);
+	__kvm_arch_free_vm(kvm);
 }
 #endif
 
@@ -1127,7 +1251,7 @@
 {
 }
 
-static inline bool kvm_arch_has_assigned_device(struct kvm *kvm)
+static __always_inline bool kvm_arch_has_assigned_device(struct kvm *kvm)
 {
 	return false;
 }
@@ -1806,6 +1930,8 @@
 void kvm_arch_mmu_notifier_invalidate_range(struct kvm *kvm,
 					    unsigned long start, unsigned long end);
 
+void kvm_arch_guest_memory_reclaimed(struct kvm *kvm);
+
 #ifdef CONFIG_HAVE_KVM_VCPU_RUN_PID_CHANGE
 int kvm_arch_vcpu_run_pid_change(struct kvm_vcpu *vcpu);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/leds.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/leds.h
@@ -161,7 +161,7 @@
 	struct kernfs_node	*brightness_hw_changed_kn;
 #endif
 
-	/* Ensures consistent access to the LED Flash Class device */
+	/* Ensures consistent access to the LED class device */
 	struct mutex		led_access;
 };
 
@@ -356,11 +356,14 @@
 	int		(*activate)(struct led_classdev *led_cdev);
 	void		(*deactivate)(struct led_classdev *led_cdev);
 
+	/* Brightness set by led_trigger_event */
+	enum led_brightness brightness;
+
 	/* LED-private triggers have this set */
 	struct led_hw_trigger_type *trigger_type;
 
 	/* LEDs under control by this trigger (for simple triggers) */
-	rwlock_t	  leddev_list_lock;
+	spinlock_t	  leddev_list_lock;
 	struct list_head  led_cdevs;
 
 	/* Link to next registered trigger */
@@ -409,22 +412,11 @@
 	return led_cdev->trigger_data;
 }
 
-/**
- * led_trigger_rename_static - rename a trigger
- * @name: the new trigger name
- * @trig: the LED trigger to rename
- *
- * Change a LED trigger name by copying the string passed in
- * name into current trigger name, which MUST be large
- * enough for the new string.
- *
- * Note that name must NOT point to the same string used
- * during LED registration, as that could lead to races.
- *
- * This is meant to be used on triggers with statically
- * allocated name.
- */
-void led_trigger_rename_static(const char *name, struct led_trigger *trig);
+static inline enum led_brightness
+led_trigger_get_brightness(const struct led_trigger *trigger)
+{
+	return trigger ? trigger->brightness : LED_OFF;
+}
 
 #define module_led_trigger(__led_trigger) \
 	module_driver(__led_trigger, led_trigger_register, \
@@ -462,6 +454,12 @@
 	return NULL;
 }
 
+static inline enum led_brightness
+led_trigger_get_brightness(const struct led_trigger *trigger)
+{
+	return LED_OFF;
+}
+
 #endif /* CONFIG_LEDS_TRIGGERS */
 
 /* Trigger specific functions */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/libata.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/libata.h
@@ -191,7 +191,7 @@
 	ATA_LFLAG_NO_LPM	= (1 << 8), /* disable LPM on this link */
 	ATA_LFLAG_RST_ONCE	= (1 << 9), /* limit recovery to one reset */
 	ATA_LFLAG_CHANGED	= (1 << 10), /* LPM state changed on this link */
-	ATA_LFLAG_NO_DB_DELAY	= (1 << 11), /* no debounce delay on link resume */
+	ATA_LFLAG_NO_DEBOUNCE_DELAY = (1 << 11), /* no debounce delay on link resume */
 
 	/* struct ata_port flags */
 	ATA_FLAG_SLAVE_POSS	= (1 << 0), /* host supports slave dev */
@@ -264,6 +264,10 @@
 	ATA_HOST_PARALLEL_SCAN	= (1 << 2),	/* Ports on this host can be scanned in parallel */
 	ATA_HOST_IGNORE_ATA	= (1 << 3),	/* Ignore ATA devices on this host. */
 
+	ATA_HOST_NO_PART	= (1 << 4), /* Host does not support partial */
+	ATA_HOST_NO_SSC		= (1 << 5), /* Host does not support slumber */
+	ATA_HOST_NO_DEVSLP	= (1 << 6), /* Host does not support devslp */
+
 	/* bits 24:31 of host->flags are reserved for LLD specific flags */
 
 	/* various lengths of time */
@@ -297,7 +301,7 @@
 	 * advised to wait only for the following duration before
 	 * doing SRST.
 	 */
-	ATA_TMOUT_PMP_SRST_WAIT	= 5000,
+	ATA_TMOUT_PMP_SRST_WAIT	= 10000,
 
 	/* When the LPM policy is set to ATA_LPM_MAX_POWER, there might
 	 * be a spurious PHY event, so ignore the first PHY event that
@@ -394,7 +398,7 @@
 	/* This should match the actual table size of
 	 * ata_eh_cmd_timeout_table in libata-eh.c.
 	 */
-	ATA_EH_CMD_TIMEOUT_TABLE_SIZE = 6,
+	ATA_EH_CMD_TIMEOUT_TABLE_SIZE = 7,
 
 	/* Horkage types. May be set by libata or controller on drives
 	   (some horkage may be drive/controller pair dependent */
@@ -565,7 +569,10 @@
 	u8			hob_lbam;
 	u8			hob_lbah;
 
-	u8			feature;
+	union {
+		u8		error;
+		u8		feature;
+	};
 	u8			nsect;
 	u8			lbal;
 	u8			lbam;
@@ -573,7 +580,10 @@
 
 	u8			device;
 
-	u8			command;	/* IO operation */
+	union {
+		u8		status;
+		u8		command;
+	};
 
 	u32			auxiliary;	/* auxiliary field */
 						/* from SATA 3.1 and */
@@ -864,7 +874,7 @@
 
 	struct mutex		scsi_scan_mutex;
 	struct delayed_work	hotplug_task;
-	struct work_struct	scsi_rescan_task;
+	struct delayed_work	scsi_rescan_task;
 
 	unsigned int		hsm_task_state;
 
@@ -1471,51 +1481,61 @@
 	return link->pmp;
 }
 
-/*
- * printk helpers
- */
-__printf(3, 4)
-void ata_port_printk(const struct ata_port *ap, const char *level,
-		     const char *fmt, ...);
-__printf(3, 4)
-void ata_link_printk(const struct ata_link *link, const char *level,
-		     const char *fmt, ...);
-__printf(3, 4)
-void ata_dev_printk(const struct ata_device *dev, const char *level,
-		    const char *fmt, ...);
+#define ata_port_printk(level, ap, fmt, ...)			\
+	pr_ ## level ("ata%u: " fmt, (ap)->print_id, ##__VA_ARGS__)
 
 #define ata_port_err(ap, fmt, ...)				\
-	ata_port_printk(ap, KERN_ERR, fmt, ##__VA_ARGS__)
+	ata_port_printk(err, ap, fmt, ##__VA_ARGS__)
 #define ata_port_warn(ap, fmt, ...)				\
-	ata_port_printk(ap, KERN_WARNING, fmt, ##__VA_ARGS__)
+	ata_port_printk(warn, ap, fmt, ##__VA_ARGS__)
 #define ata_port_notice(ap, fmt, ...)				\
-	ata_port_printk(ap, KERN_NOTICE, fmt, ##__VA_ARGS__)
+	ata_port_printk(notice, ap, fmt, ##__VA_ARGS__)
 #define ata_port_info(ap, fmt, ...)				\
-	ata_port_printk(ap, KERN_INFO, fmt, ##__VA_ARGS__)
+	ata_port_printk(info, ap, fmt, ##__VA_ARGS__)
 #define ata_port_dbg(ap, fmt, ...)				\
-	ata_port_printk(ap, KERN_DEBUG, fmt, ##__VA_ARGS__)
+	ata_port_printk(debug, ap, fmt, ##__VA_ARGS__)
+
+#define ata_link_printk(level, link, fmt, ...)			\
+do {								\
+	if (sata_pmp_attached((link)->ap) ||			\
+	    (link)->ap->slave_link)				\
+		pr_ ## level ("ata%u.%02u: " fmt,		\
+			      (link)->ap->print_id,		\
+			      (link)->pmp,			\
+			      ##__VA_ARGS__);			\
+        else							\
+		pr_ ## level ("ata%u: " fmt,			\
+			      (link)->ap->print_id,		\
+			      ##__VA_ARGS__);			\
+} while (0)
 
 #define ata_link_err(link, fmt, ...)				\
-	ata_link_printk(link, KERN_ERR, fmt, ##__VA_ARGS__)
+	ata_link_printk(err, link, fmt, ##__VA_ARGS__)
 #define ata_link_warn(link, fmt, ...)				\
-	ata_link_printk(link, KERN_WARNING, fmt, ##__VA_ARGS__)
+	ata_link_printk(warn, link, fmt, ##__VA_ARGS__)
 #define ata_link_notice(link, fmt, ...)				\
-	ata_link_printk(link, KERN_NOTICE, fmt, ##__VA_ARGS__)
+	ata_link_printk(notice, link, fmt, ##__VA_ARGS__)
 #define ata_link_info(link, fmt, ...)				\
-	ata_link_printk(link, KERN_INFO, fmt, ##__VA_ARGS__)
+	ata_link_printk(info, link, fmt, ##__VA_ARGS__)
 #define ata_link_dbg(link, fmt, ...)				\
-	ata_link_printk(link, KERN_DEBUG, fmt, ##__VA_ARGS__)
+	ata_link_printk(debug, link, fmt, ##__VA_ARGS__)
+
+#define ata_dev_printk(level, dev, fmt, ...)			\
+        pr_ ## level("ata%u.%02u: " fmt,			\
+               (dev)->link->ap->print_id,			\
+	       (dev)->link->pmp + (dev)->devno,			\
+	       ##__VA_ARGS__)
 
 #define ata_dev_err(dev, fmt, ...)				\
-	ata_dev_printk(dev, KERN_ERR, fmt, ##__VA_ARGS__)
+	ata_dev_printk(err, dev, fmt, ##__VA_ARGS__)
 #define ata_dev_warn(dev, fmt, ...)				\
-	ata_dev_printk(dev, KERN_WARNING, fmt, ##__VA_ARGS__)
+	ata_dev_printk(warn, dev, fmt, ##__VA_ARGS__)
 #define ata_dev_notice(dev, fmt, ...)				\
-	ata_dev_printk(dev, KERN_NOTICE, fmt, ##__VA_ARGS__)
+	ata_dev_printk(notice, dev, fmt, ##__VA_ARGS__)
 #define ata_dev_info(dev, fmt, ...)				\
-	ata_dev_printk(dev, KERN_INFO, fmt, ##__VA_ARGS__)
+	ata_dev_printk(info, dev, fmt, ##__VA_ARGS__)
 #define ata_dev_dbg(dev, fmt, ...)				\
-	ata_dev_printk(dev, KERN_DEBUG, fmt, ##__VA_ARGS__)
+	ata_dev_printk(debug, dev, fmt, ##__VA_ARGS__)
 
 void ata_print_version(const struct device *dev, const char *version);
 
@@ -2049,11 +2069,8 @@
 {
 	u8 status = ata_sff_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
 
-#ifdef ATA_DEBUG
 	if (status != 0xff && (status & (ATA_BUSY | ATA_DRQ)))
-		ata_port_printk(ap, KERN_DEBUG, "abnormal Status 0x%X\n",
-				status);
-#endif
+		ata_port_dbg(ap, "abnormal Status 0x%X\n", status);
 
 	return status;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/linkage.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/linkage.h
@@ -69,8 +69,8 @@
 #endif
 
 #ifndef __ALIGN
-#define __ALIGN		.align 4,0x90
-#define __ALIGN_STR	".align 4,0x90"
+#define __ALIGN			.balign CONFIG_FUNCTION_ALIGNMENT
+#define __ALIGN_STR		__stringify(__ALIGN)
 #endif
 
 #ifdef __ASSEMBLY__
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/list.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/list.h
@@ -33,7 +33,7 @@
 static inline void INIT_LIST_HEAD(struct list_head *list)
 {
 	WRITE_ONCE(list->next, list);
-	list->prev = list;
+	WRITE_ONCE(list->prev, list);
 }
 
 #ifdef CONFIG_DEBUG_LIST
@@ -256,8 +256,7 @@
  * @list: the entry to test
  * @head: the head of the list
  */
-static inline int list_is_first(const struct list_head *list,
-					const struct list_head *head)
+static inline int list_is_first(const struct list_head *list, const struct list_head *head)
 {
 	return list->prev == head;
 }
@@ -267,13 +266,22 @@
  * @list: the entry to test
  * @head: the head of the list
  */
-static inline int list_is_last(const struct list_head *list,
-				const struct list_head *head)
+static inline int list_is_last(const struct list_head *list, const struct list_head *head)
 {
 	return list->next == head;
 }
 
 /**
+ * list_is_head - tests whether @list is the list @head
+ * @list: the entry to test
+ * @head: the head of the list
+ */
+static inline int list_is_head(const struct list_head *list, const struct list_head *head)
+{
+	return list == head;
+}
+
+/**
  * list_empty - tests whether a list is empty
  * @head: the list to test.
  */
@@ -296,7 +304,7 @@
 static inline void list_del_init_careful(struct list_head *entry)
 {
 	__list_del_entry(entry);
-	entry->prev = entry;
+	WRITE_ONCE(entry->prev, entry);
 	smp_store_release(&entry->next, entry);
 }
 
@@ -316,7 +324,7 @@
 static inline int list_empty_careful(const struct list_head *head)
 {
 	struct list_head *next = smp_load_acquire(&head->next);
-	return (next == head) && (next == head->prev);
+	return list_is_head(next, head) && (next == READ_ONCE(head->prev));
 }
 
 /**
@@ -391,10 +399,9 @@
 {
 	if (list_empty(head))
 		return;
-	if (list_is_singular(head) &&
-		(head->next != entry && head != entry))
+	if (list_is_singular(head) && !list_is_head(entry, head) && (entry != head->next))
 		return;
-	if (entry == head)
+	if (list_is_head(entry, head))
 		INIT_LIST_HEAD(list);
 	else
 		__list_cut_position(list, head, entry);
@@ -568,7 +575,17 @@
  * @head:	the head for your list.
  */
 #define list_for_each(pos, head) \
-	for (pos = (head)->next; pos != (head); pos = pos->next)
+	for (pos = (head)->next; !list_is_head(pos, (head)); pos = pos->next)
+
+/**
+ * list_for_each_rcu - Iterate over a list in an RCU-safe fashion
+ * @pos:	the &struct list_head to use as a loop cursor.
+ * @head:	the head for your list.
+ */
+#define list_for_each_rcu(pos, head)		  \
+	for (pos = rcu_dereference((head)->next); \
+	     !list_is_head(pos, (head)); \
+	     pos = rcu_dereference(pos->next))
 
 /**
  * list_for_each_continue - continue iteration over a list
@@ -578,7 +595,7 @@
  * Continue to iterate over a list, continuing after the current position.
  */
 #define list_for_each_continue(pos, head) \
-	for (pos = pos->next; pos != (head); pos = pos->next)
+	for (pos = pos->next; !list_is_head(pos, (head)); pos = pos->next)
 
 /**
  * list_for_each_prev	-	iterate over a list backwards
@@ -586,7 +603,7 @@
  * @head:	the head for your list.
  */
 #define list_for_each_prev(pos, head) \
-	for (pos = (head)->prev; pos != (head); pos = pos->prev)
+	for (pos = (head)->prev; !list_is_head(pos, (head)); pos = pos->prev)
 
 /**
  * list_for_each_safe - iterate over a list safe against removal of list entry
@@ -595,8 +612,9 @@
  * @head:	the head for your list.
  */
 #define list_for_each_safe(pos, n, head) \
-	for (pos = (head)->next, n = pos->next; pos != (head); \
-		pos = n, n = pos->next)
+	for (pos = (head)->next, n = pos->next; \
+	     !list_is_head(pos, (head)); \
+	     pos = n, n = pos->next)
 
 /**
  * list_for_each_prev_safe - iterate over a list backwards safe against removal of list entry
@@ -606,7 +624,7 @@
  */
 #define list_for_each_prev_safe(pos, n, head) \
 	for (pos = (head)->prev, n = pos->prev; \
-	     pos != (head); \
+	     !list_is_head(pos, (head)); \
 	     pos = n, n = pos->prev)
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/lockd/lockd.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/lockd/lockd.h
@@ -292,6 +292,7 @@
 __be32		  nlm_lookup_file(struct svc_rqst *, struct nlm_file **,
 					struct nlm_lock *);
 void		  nlm_release_file(struct nlm_file *);
+void		  nlmsvc_put_lockowner(struct nlm_lockowner *);
 void		  nlmsvc_release_lockowner(struct nlm_lock *);
 void		  nlmsvc_mark_resources(struct net *);
 void		  nlmsvc_free_host_resources(struct nlm_host *);
@@ -303,10 +304,15 @@
 int           nlmsvc_unlock_all_by_sb(struct super_block *sb);
 int           nlmsvc_unlock_all_by_ip(struct sockaddr *server_addr);
 
+static inline struct file *nlmsvc_file_file(struct nlm_file *file)
+{
+	return file->f_file[O_RDONLY] ?
+	       file->f_file[O_RDONLY] : file->f_file[O_WRONLY];
+}
+
 static inline struct inode *nlmsvc_file_inode(struct nlm_file *file)
 {
-	return locks_inode(file->f_file[O_RDONLY] ?
-			   file->f_file[O_RDONLY] : file->f_file[O_WRONLY]);
+	return locks_inode(nlmsvc_file_file(file));
 }
 
 static inline int __nlm_privileged_request4(const struct sockaddr *sap)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/lockd/xdr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/lockd/xdr.h
@@ -41,6 +41,8 @@
 	struct nfs_fh		fh;
 	struct xdr_netobj	oh;
 	u32			svid;
+	u64			lock_start;
+	u64			lock_len;
 	struct file_lock	fl;
 };
 
@@ -96,18 +98,19 @@
  */
 #define NLMSVC_XDRSIZE		sizeof(struct nlm_args)
 
-int	nlmsvc_decode_testargs(struct svc_rqst *, __be32 *);
-int	nlmsvc_encode_testres(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_lockargs(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_cancargs(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_unlockargs(struct svc_rqst *, __be32 *);
-int	nlmsvc_encode_res(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_res(struct svc_rqst *, __be32 *);
-int	nlmsvc_encode_void(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_void(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_shareargs(struct svc_rqst *, __be32 *);
-int	nlmsvc_encode_shareres(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_notify(struct svc_rqst *, __be32 *);
-int	nlmsvc_decode_reboot(struct svc_rqst *, __be32 *);
+bool	nlmsvc_decode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_testargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_lockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_cancargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_unlockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_reboot(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_shareargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_decode_notify(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+
+bool	nlmsvc_encode_testres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_encode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_encode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlmsvc_encode_shareres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
 
 #endif /* LOCKD_XDR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/lockd/xdr4.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/lockd/xdr4.h
@@ -22,21 +22,21 @@
 #define	nlm4_fbig		cpu_to_be32(NLM_FBIG)
 #define	nlm4_failed		cpu_to_be32(NLM_FAILED)
 
+void	nlm4svc_set_file_lock_range(struct file_lock *fl, u64 off, u64 len);
+bool	nlm4svc_decode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_testargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_lockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_cancargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_unlockargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_reboot(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_shareargs(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_decode_notify(struct svc_rqst *rqstp, struct xdr_stream *xdr);
 
-
-int	nlm4svc_decode_testargs(struct svc_rqst *, __be32 *);
-int	nlm4svc_encode_testres(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_lockargs(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_cancargs(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_unlockargs(struct svc_rqst *, __be32 *);
-int	nlm4svc_encode_res(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_res(struct svc_rqst *, __be32 *);
-int	nlm4svc_encode_void(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_void(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_shareargs(struct svc_rqst *, __be32 *);
-int	nlm4svc_encode_shareres(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_notify(struct svc_rqst *, __be32 *);
-int	nlm4svc_decode_reboot(struct svc_rqst *, __be32 *);
+bool	nlm4svc_encode_testres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_encode_res(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_encode_void(struct svc_rqst *rqstp, struct xdr_stream *xdr);
+bool	nlm4svc_encode_shareres(struct svc_rqst *rqstp, struct xdr_stream *xdr);
 
 extern const struct rpc_version nlm_version4;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/lockdep.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/lockdep.h
@@ -192,7 +192,7 @@
 lockdep_init_map_waits(struct lockdep_map *lock, const char *name,
 		       struct lock_class_key *key, int subclass, u8 inner, u8 outer)
 {
-	lockdep_init_map_type(lock, name, key, subclass, inner, LD_WAIT_INV, LD_LOCK_NORMAL);
+	lockdep_init_map_type(lock, name, key, subclass, inner, outer, LD_LOCK_NORMAL);
 }
 
 static inline void
@@ -215,24 +215,28 @@
  * or they are too narrow (they suffer from a false class-split):
  */
 #define lockdep_set_class(lock, key)				\
-	lockdep_init_map_waits(&(lock)->dep_map, #key, key, 0,	\
-			       (lock)->dep_map.wait_type_inner,	\
-			       (lock)->dep_map.wait_type_outer)
+	lockdep_init_map_type(&(lock)->dep_map, #key, key, 0,	\
+			      (lock)->dep_map.wait_type_inner,	\
+			      (lock)->dep_map.wait_type_outer,	\
+			      (lock)->dep_map.lock_type)
 
 #define lockdep_set_class_and_name(lock, key, name)		\
-	lockdep_init_map_waits(&(lock)->dep_map, name, key, 0,	\
-			       (lock)->dep_map.wait_type_inner,	\
-			       (lock)->dep_map.wait_type_outer)
+	lockdep_init_map_type(&(lock)->dep_map, name, key, 0,	\
+			      (lock)->dep_map.wait_type_inner,	\
+			      (lock)->dep_map.wait_type_outer,	\
+			      (lock)->dep_map.lock_type)
 
 #define lockdep_set_class_and_subclass(lock, key, sub)		\
-	lockdep_init_map_waits(&(lock)->dep_map, #key, key, sub,\
-			       (lock)->dep_map.wait_type_inner,	\
-			       (lock)->dep_map.wait_type_outer)
+	lockdep_init_map_type(&(lock)->dep_map, #key, key, sub,	\
+			      (lock)->dep_map.wait_type_inner,	\
+			      (lock)->dep_map.wait_type_outer,	\
+			      (lock)->dep_map.lock_type)
 
 #define lockdep_set_subclass(lock, sub)					\
-	lockdep_init_map_waits(&(lock)->dep_map, #lock, (lock)->dep_map.key, sub,\
-			       (lock)->dep_map.wait_type_inner,		\
-			       (lock)->dep_map.wait_type_outer)
+	lockdep_init_map_type(&(lock)->dep_map, (lock)->dep_map.name, (lock)->dep_map.key, sub,\
+			      (lock)->dep_map.wait_type_inner,		\
+			      (lock)->dep_map.wait_type_outer,		\
+			      (lock)->dep_map.lock_type)
 
 #define lockdep_set_novalidate_class(lock) \
 	lockdep_set_class_and_name(lock, &__lockdep_no_validate__, #lock)
@@ -248,6 +252,8 @@
 	return lock->key == key;
 }
 
+struct lock_class *lockdep_hlock_class(struct held_lock *hlock);
+
 /*
  * Acquire a lock.
  *
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/lsm_hook_defs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/lsm_hook_defs.h
@@ -26,13 +26,13 @@
  *   #undef LSM_HOOK
  * };
  */
-LSM_HOOK(int, 0, binder_set_context_mgr, struct task_struct *mgr)
-LSM_HOOK(int, 0, binder_transaction, struct task_struct *from,
-	 struct task_struct *to)
-LSM_HOOK(int, 0, binder_transfer_binder, struct task_struct *from,
-	 struct task_struct *to)
-LSM_HOOK(int, 0, binder_transfer_file, struct task_struct *from,
-	 struct task_struct *to, struct file *file)
+LSM_HOOK(int, 0, binder_set_context_mgr, const struct cred *mgr)
+LSM_HOOK(int, 0, binder_transaction, const struct cred *from,
+	 const struct cred *to)
+LSM_HOOK(int, 0, binder_transfer_binder, const struct cred *from,
+	 const struct cred *to)
+LSM_HOOK(int, 0, binder_transfer_file, const struct cred *from,
+	 const struct cred *to, struct file *file)
 LSM_HOOK(int, 0, ptrace_access_check, struct task_struct *child,
 	 unsigned int mode)
 LSM_HOOK(int, 0, ptrace_traceme, struct task_struct *parent)
@@ -48,7 +48,7 @@
 LSM_HOOK(int, 0, syslog, int type)
 LSM_HOOK(int, 0, settime, const struct timespec64 *ts,
 	 const struct timezone *tz)
-LSM_HOOK(int, 0, vm_enough_memory, struct mm_struct *mm, long pages)
+LSM_HOOK(int, 1, vm_enough_memory, struct mm_struct *mm, long pages)
 LSM_HOOK(int, 0, bprm_creds_for_exec, struct linux_binprm *bprm)
 LSM_HOOK(int, 0, bprm_creds_from_file, struct linux_binprm *bprm, struct file *file)
 LSM_HOOK(int, 0, bprm_check_security, struct linux_binprm *bprm)
@@ -165,6 +165,8 @@
 LSM_HOOK(void, LSM_RET_VOID, file_free_security, struct file *file)
 LSM_HOOK(int, 0, file_ioctl, struct file *file, unsigned int cmd,
 	 unsigned long arg)
+LSM_HOOK(int, 0, file_ioctl_compat, struct file *file, unsigned int cmd,
+	 unsigned long arg)
 LSM_HOOK(int, 0, mmap_addr, unsigned long addr)
 LSM_HOOK(int, 0, mmap_file, struct file *file, unsigned long reqprot,
 	 unsigned long prot, unsigned long flags)
@@ -265,7 +267,7 @@
 LSM_HOOK(void, LSM_RET_VOID, inode_invalidate_secctx, struct inode *inode)
 LSM_HOOK(int, 0, inode_notifysecctx, struct inode *inode, void *ctx, u32 ctxlen)
 LSM_HOOK(int, 0, inode_setsecctx, struct dentry *dentry, void *ctx, u32 ctxlen)
-LSM_HOOK(int, 0, inode_getsecctx, struct inode *inode, void **ctx,
+LSM_HOOK(int, -EOPNOTSUPP, inode_getsecctx, struct inode *inode, void **ctx,
 	 u32 *ctxlen)
 
 #if defined(CONFIG_SECURITY) && defined(CONFIG_WATCH_QUEUE)
@@ -377,7 +379,7 @@
 
 #ifdef CONFIG_AUDIT
 LSM_HOOK(int, 0, audit_rule_init, u32 field, u32 op, char *rulestr,
-	 void **lsmrule)
+	 void **lsmrule, gfp_t gfp)
 LSM_HOOK(int, 0, audit_rule_known, struct audit_krule *krule)
 LSM_HOOK(int, 0, audit_rule_match, u32 secid, u32 field, u32 op, void *lsmrule)
 LSM_HOOK(void, LSM_RET_VOID, audit_rule_free, void *lsmrule)
@@ -394,6 +396,8 @@
 #endif /* CONFIG_BPF_SYSCALL */
 
 LSM_HOOK(int, 0, locked_down, enum lockdown_reason what)
+LSM_HOOK(int, 0, lock_kernel_down, const char *where, enum lockdown_reason level)
+
 
 #ifdef CONFIG_PERF_EVENTS
 LSM_HOOK(int, 0, perf_event_open, struct perf_event_attr *attr, int type)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/lsm_hooks.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/lsm_hooks.h
@@ -1313,22 +1313,22 @@
  *
  * @binder_set_context_mgr:
  *	Check whether @mgr is allowed to be the binder context manager.
- *	@mgr contains the task_struct for the task being registered.
+ *	@mgr contains the struct cred for the current binder process.
  *	Return 0 if permission is granted.
  * @binder_transaction:
  *	Check whether @from is allowed to invoke a binder transaction call
  *	to @to.
- *	@from contains the task_struct for the sending task.
- *	@to contains the task_struct for the receiving task.
+ *	@from contains the struct cred for the sending process.
+ *	@to contains the struct cred for the receiving process.
  * @binder_transfer_binder:
  *	Check whether @from is allowed to transfer a binder reference to @to.
- *	@from contains the task_struct for the sending task.
- *	@to contains the task_struct for the receiving task.
+ *	@from contains the struct cred for the sending process.
+ *	@to contains the struct cred for the receiving process.
  * @binder_transfer_file:
  *	Check whether @from is allowed to transfer @file to @to.
- *	@from contains the task_struct for the sending task.
+ *	@from contains the struct cred for the sending process.
  *	@file contains the struct file being transferred.
- *	@to contains the task_struct for the receiving task.
+ *	@to contains the struct cred for the receiving process.
  *
  * @ptrace_access_check:
  *	Check permission before allowing the current process to trace the
@@ -1397,6 +1397,12 @@
  *	@pages contains the number of pages.
  *	Return 0 if permission is granted.
  *
+ * @getprocattr:
+ *	Provide the named process attribute for display in special files in
+ *	the /proc/.../attr directory.  Attribute naming and the data displayed
+ *	is at the discretion of the security modules.  The exception is the
+ *	"context" attribute, which will contain the security context of the
+ *	task as a nul terminated text string without trailing whitespace.
  * @ismaclabel:
  *	Check if the extended attribute specified by @name
  *	represents a MAC label. Returns 1 if name is a MAC
@@ -1545,6 +1551,12 @@
  *
  *     @what: kernel feature being accessed
  *
+ * @lock_kernel_down
+ * 	Put the kernel into lock-down mode.
+ *
+ * 	@where: Where the lock-down is originating from (e.g. command line option)
+ * 	@level: The lock-down level (can only increase)
+ *
  * Security hooks for perf events
  *
  * @perf_event_open:
@@ -1571,6 +1583,14 @@
 } __randomize_layout;
 
 /*
+ * Information that identifies a security module.
+ */
+struct lsm_id {
+	const char	*lsm;	/* Name of the LSM */
+	int		slot;	/* Slot in lsmblob if one is allocated */
+};
+
+/*
  * Security module hook list structure.
  * For use with generic list macros for common operations.
  */
@@ -1578,7 +1598,7 @@
 	struct hlist_node		list;
 	struct hlist_head		*head;
 	union security_list_options	hook;
-	char				*lsm;
+	struct lsm_id			*lsmid;
 } __randomize_layout;
 
 /*
@@ -1589,6 +1609,7 @@
 	int	lbs_file;
 	int	lbs_inode;
 	int	lbs_superblock;
+	int	lbs_sock;
 	int	lbs_ipc;
 	int	lbs_msg_msg;
 	int	lbs_task;
@@ -1613,7 +1634,7 @@
 extern char *lsm_names;
 
 extern void security_add_hooks(struct security_hook_list *hooks, int count,
-				char *lsm);
+			       struct lsm_id *lsmid);
 
 #define LSM_FLAG_LEGACY_MAJOR	BIT(0)
 #define LSM_FLAG_EXCLUSIVE	BIT(1)
@@ -1677,4 +1698,32 @@
 
 extern int lsm_inode_alloc(struct inode *inode);
 
+/**
+ * lsm_task_display - the "display" LSM for this task
+ * @task: The task to report on
+ *
+ * Returns the task's display LSM slot.
+ */
+static inline int lsm_task_display(struct task_struct *task)
+{
+#ifdef CONFIG_SECURITY
+	int *display = task->security;
+
+	if (display)
+		return *display;
+#endif
+	return LSMBLOB_INVALID;
+}
+
+/* Same as lsm_task_display(), using struct cred as input */
+static inline int lsm_cred_display(struct cred *cred)
+{
+#ifdef CONFIG_SECURITY
+	int *display = cred->security;
+
+	if (display)
+		return *display;
+#endif
+	return LSMBLOB_INVALID;
+}
 #endif /* ! __LINUX_LSM_HOOKS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mailbox/zynqmp-ipi-message.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mailbox/zynqmp-ipi-message.h
@@ -9,7 +9,7 @@
  * @data: message payload
  *
  * This is the structure for data used in mbox_send_message
- * the maximum length of data buffer is fixed to 12 bytes.
+ * the maximum length of data buffer is fixed to 32 bytes.
  * Client is supposed to be aware of this.
  */
 struct zynqmp_ipi_message {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mailbox_controller.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mailbox_controller.h
@@ -83,6 +83,7 @@
 				      const struct of_phandle_args *sp);
 	/* Internal to API */
 	struct hrtimer poll_hrt;
+	spinlock_t poll_hrt_lock;
 	struct list_head node;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mbcache.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mbcache.h
@@ -10,16 +10,29 @@
 
 struct mb_cache;
 
+/* Cache entry flags */
+enum {
+	MBE_REFERENCED_B = 0,
+	MBE_REUSABLE_B
+};
+
 struct mb_cache_entry {
 	/* List of entries in cache - protected by cache->c_list_lock */
 	struct list_head	e_list;
-	/* Hash table list - protected by hash chain bitlock */
+	/*
+	 * Hash table list - protected by hash chain bitlock. The entry is
+	 * guaranteed to be hashed while e_refcnt > 0.
+	 */
 	struct hlist_bl_node	e_hash_list;
+	/*
+	 * Entry refcount. Once it reaches zero, entry is unhashed and freed.
+	 * While refcount > 0, the entry is guaranteed to stay in the hash and
+	 * e.g. mb_cache_entry_try_delete() will fail.
+	 */
 	atomic_t		e_refcnt;
 	/* Key in hash - stable during lifetime of the entry */
 	u32			e_key;
-	u32			e_referenced:1;
-	u32			e_reusable:1;
+	unsigned long		e_flags;
 	/* User provided value - stable during lifetime of the entry */
 	u64			e_value;
 };
@@ -29,16 +42,24 @@
 
 int mb_cache_entry_create(struct mb_cache *cache, gfp_t mask, u32 key,
 			  u64 value, bool reusable);
-void __mb_cache_entry_free(struct mb_cache_entry *entry);
-static inline int mb_cache_entry_put(struct mb_cache *cache,
-				     struct mb_cache_entry *entry)
+void __mb_cache_entry_free(struct mb_cache *cache,
+			   struct mb_cache_entry *entry);
+void mb_cache_entry_wait_unused(struct mb_cache_entry *entry);
+static inline void mb_cache_entry_put(struct mb_cache *cache,
+				      struct mb_cache_entry *entry)
 {
-	if (!atomic_dec_and_test(&entry->e_refcnt))
-		return 0;
-	__mb_cache_entry_free(entry);
-	return 1;
+	unsigned int cnt = atomic_dec_return(&entry->e_refcnt);
+
+	if (cnt > 0) {
+		if (cnt <= 2)
+			wake_up_var(&entry->e_refcnt);
+		return;
+	}
+	__mb_cache_entry_free(cache, entry);
 }
 
+struct mb_cache_entry *mb_cache_entry_delete_or_get(struct mb_cache *cache,
+						    u32 key, u64 value);
 void mb_cache_entry_delete(struct mb_cache *cache, u32 key, u64 value);
 struct mb_cache_entry *mb_cache_entry_get(struct mb_cache *cache, u32 key,
 					  u64 value);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mc146818rtc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mc146818rtc.h
@@ -86,6 +86,8 @@
    /* 2 values for divider stage reset, others for "testing purposes only" */
 #  define RTC_DIV_RESET1	0x60
 #  define RTC_DIV_RESET2	0x70
+   /* In AMD BKDG bit 5 and 6 are reserved, bit 4 is for select dv0 bank */
+#  define RTC_AMD_BANK_SELECT	0x10
   /* Periodic intr. / Square wave rate select. 0=none, 1=32.8kHz,... 15=2Hz */
 # define RTC_RATE_SELECT 	0x0F
 
@@ -123,7 +125,11 @@
 #define RTC_IO_EXTENT_USED      RTC_IO_EXTENT
 #endif /* ARCH_RTC_LOCATION */
 
-unsigned int mc146818_get_time(struct rtc_time *time);
+bool mc146818_does_rtc_work(void);
+int mc146818_get_time(struct rtc_time *time);
 int mc146818_set_time(struct rtc_time *time);
 
+bool mc146818_avoid_UIP(void (*callback)(unsigned char seconds, void *param),
+			void *param);
+
 #endif /* _MC146818RTC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mcb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mcb.h
@@ -63,7 +63,6 @@
 struct mcb_device {
 	struct device dev;
 	struct mcb_bus *bus;
-	bool is_added;
 	struct mcb_driver *driver;
 	u16 id;
 	int inst;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mdio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mdio.h
@@ -7,6 +7,7 @@
 #define __LINUX_MDIO_H__
 
 #include <uapi/linux/mdio.h>
+#include <linux/bitfield.h>
 #include <linux/mod_devicetable.h>
 
 /* Or MII_ADDR_C45 into regnum for read/write on mii_bus to enable the 21 bit
@@ -14,6 +15,7 @@
  */
 #define MII_ADDR_C45		(1<<30)
 #define MII_DEVADDR_C45_SHIFT	16
+#define MII_DEVADDR_C45_MASK	GENMASK(20, 16)
 #define MII_REGADDR_C45_MASK	GENMASK(15, 0)
 
 struct gpio_desc;
@@ -355,6 +357,16 @@
 	return MII_ADDR_C45 | devad << MII_DEVADDR_C45_SHIFT | regnum;
 }
 
+static inline u16 mdiobus_c45_regad(u32 regnum)
+{
+	return FIELD_GET(MII_REGADDR_C45_MASK, regnum);
+}
+
+static inline u16 mdiobus_c45_devad(u32 regnum)
+{
+	return FIELD_GET(MII_DEVADDR_C45_MASK, regnum);
+}
+
 static inline int __mdiobus_c45_read(struct mii_bus *bus, int prtad, int devad,
 				     u16 regnum)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/memblock.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/memblock.h
@@ -100,7 +100,8 @@
 #endif
 
 void memblock_allow_resize(void);
-int memblock_add_node(phys_addr_t base, phys_addr_t size, int nid);
+int memblock_add_node(phys_addr_t base, phys_addr_t size, int nid,
+		      enum memblock_flags flags);
 int memblock_add(phys_addr_t base, phys_addr_t size);
 int memblock_remove(phys_addr_t base, phys_addr_t size);
 int memblock_free(phys_addr_t base, phys_addr_t size);
@@ -388,8 +389,8 @@
 				      phys_addr_t end, int nid, bool exact_nid);
 phys_addr_t memblock_phys_alloc_try_nid(phys_addr_t size, phys_addr_t align, int nid);
 
-static inline phys_addr_t memblock_phys_alloc(phys_addr_t size,
-					      phys_addr_t align)
+static __always_inline phys_addr_t memblock_phys_alloc(phys_addr_t size,
+						       phys_addr_t align)
 {
 	return memblock_phys_alloc_range(size, align, 0,
 					 MEMBLOCK_ALLOC_ACCESSIBLE);
@@ -441,18 +442,6 @@
 				      MEMBLOCK_ALLOC_ACCESSIBLE, nid);
 }
 
-static inline void memblock_free_early(phys_addr_t base,
-					      phys_addr_t size)
-{
-	memblock_free(base, size);
-}
-
-static inline void memblock_free_early_nid(phys_addr_t base,
-						  phys_addr_t size, int nid)
-{
-	memblock_free(base, size);
-}
-
 static inline void memblock_free_late(phys_addr_t base, phys_addr_t size)
 {
 	__memblock_free_late(base, size);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/memcontrol.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/memcontrol.h
@@ -223,7 +223,7 @@
 	struct mem_cgroup *memcg;
 	atomic_t nr_charged_bytes;
 	union {
-		struct list_head list;
+		struct list_head list; /* protected by objcg_lock */
 		struct rcu_head rcu;
 	};
 };
@@ -310,6 +310,11 @@
 	atomic_long_t		memory_events[MEMCG_NR_MEMORY_EVENTS];
 	atomic_long_t		memory_events_local[MEMCG_NR_MEMORY_EVENTS];
 
+	/*
+	 * Hint of reclaim pressure for socket memroy management. Note
+	 * that this indicator should NOT be used in legacy cgroup mode
+	 * where socket memory is accounted/charged separately.
+	 */
 	unsigned long		socket_pressure;
 
 	/* Legacy tcp memory accounting */
@@ -320,7 +325,8 @@
 	int kmemcg_id;
 	enum memcg_kmem_state kmem_state;
 	struct obj_cgroup __rcu *objcg;
-	struct list_head objcg_list; /* list of inherited objcgs */
+	/* list of inherited objcgs, protected by objcg_lock */
+	struct list_head objcg_list;
 #endif
 
 	MEMCG_PADDING(_pad2_);
@@ -965,19 +971,30 @@
 
 static inline unsigned long memcg_page_state(struct mem_cgroup *memcg, int idx)
 {
-	return READ_ONCE(memcg->vmstats.state[idx]);
+	long x = READ_ONCE(memcg->vmstats.state[idx]);
+#ifdef CONFIG_SMP
+	if (x < 0)
+		x = 0;
+#endif
+	return x;
 }
 
 static inline unsigned long lruvec_page_state(struct lruvec *lruvec,
 					      enum node_stat_item idx)
 {
 	struct mem_cgroup_per_node *pn;
+	long x;
 
 	if (mem_cgroup_disabled())
 		return node_page_state(lruvec_pgdat(lruvec), idx);
 
 	pn = container_of(lruvec, struct mem_cgroup_per_node, lruvec);
-	return READ_ONCE(pn->lruvec_stats.state[idx]);
+	x = READ_ONCE(pn->lruvec_stats.state[idx]);
+#ifdef CONFIG_SMP
+	if (x < 0)
+		x = 0;
+#endif
+	return x;
 }
 
 static inline unsigned long lruvec_page_state_local(struct lruvec *lruvec,
@@ -1001,6 +1018,7 @@
 }
 
 void mem_cgroup_flush_stats(void);
+void mem_cgroup_flush_stats_delayed(void);
 
 void __mod_memcg_lruvec_state(struct lruvec *lruvec, enum node_stat_item idx,
 			      int val);
@@ -1421,6 +1439,10 @@
 {
 }
 
+static inline void mem_cgroup_flush_stats_delayed(void)
+{
+}
+
 static inline void __mod_memcg_lruvec_state(struct lruvec *lruvec,
 					    enum node_stat_item idx, int val)
 {
@@ -1610,8 +1632,8 @@
 void mem_cgroup_sk_free(struct sock *sk);
 static inline bool mem_cgroup_under_socket_pressure(struct mem_cgroup *memcg)
 {
-	if (!cgroup_subsys_on_dfl(memory_cgrp_subsys) && memcg->tcpmem_pressure)
-		return true;
+	if (!cgroup_subsys_on_dfl(memory_cgrp_subsys))
+		return !!memcg->tcpmem_pressure;
 	do {
 		if (time_before(jiffies, memcg->socket_pressure))
 			return true;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/memregion.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/memregion.h
@@ -16,7 +16,7 @@
 {
 	return -ENOMEM;
 }
-void memregion_free(int id)
+static inline void memregion_free(int id)
 {
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/memremap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/memremap.h
@@ -73,16 +73,6 @@
 	void (*page_free)(struct page *page);
 
 	/*
-	 * Transition the refcount in struct dev_pagemap to the dead state.
-	 */
-	void (*kill)(struct dev_pagemap *pgmap);
-
-	/*
-	 * Wait for refcount in struct dev_pagemap to be idle and reap it.
-	 */
-	void (*cleanup)(struct dev_pagemap *pgmap);
-
-	/*
 	 * Used for private (un-addressable) device memory only.  Must migrate
 	 * the page back to a CPU accessible page.
 	 */
@@ -95,8 +85,7 @@
  * struct dev_pagemap - metadata for ZONE_DEVICE mappings
  * @altmap: pre-allocated/reserved memory for vmemmap allocations
  * @ref: reference count that pins the devm_memremap_pages() mapping
- * @internal_ref: internal reference if @ref is not provided by the caller
- * @done: completion for @internal_ref
+ * @done: completion for @ref
  * @type: memory type: see MEMORY_* in memory_hotplug.h
  * @flags: PGMAP_* flags to specify defailed behavior
  * @ops: method table
@@ -109,8 +98,7 @@
  */
 struct dev_pagemap {
 	struct vmem_altmap altmap;
-	struct percpu_ref *ref;
-	struct percpu_ref internal_ref;
+	struct percpu_ref ref;
 	struct completion done;
 	enum memory_type type;
 	unsigned int flags;
@@ -191,7 +179,7 @@
 static inline void put_dev_pagemap(struct dev_pagemap *pgmap)
 {
 	if (pgmap)
-		percpu_ref_put(pgmap->ref);
+		percpu_ref_put(&pgmap->ref);
 }
 
 #endif /* _LINUX_MEMREMAP_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mfd/core.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mfd/core.h
@@ -92,7 +92,7 @@
 	 * (above) when matching OF nodes with devices that have identical
 	 * compatible strings
 	 */
-	const u64 of_reg;
+	u64 of_reg;
 
 	/* Set to 'true' to use 'of_reg' (above) - allows for of_reg=0 */
 	bool use_of_reg;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mfd/ljca.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mfd/ljca.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LINUX_USB_LJCA_H
+#define __LINUX_USB_LJCA_H
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+#define MAX_GPIO_NUM 64
+
+struct ljca_gpio_info {
+	int num;
+	DECLARE_BITMAP(valid_pin_map, MAX_GPIO_NUM);
+};
+
+struct ljca_i2c_info {
+	u8 id;
+	u8 capacity;
+	u8 intr_pin;
+};
+
+struct ljca_spi_info {
+	u8 id;
+	u8 capacity;
+};
+
+struct ljca_platform_data {
+	int type;
+	union {
+		struct ljca_gpio_info gpio_info;
+		struct ljca_i2c_info i2c_info;
+		struct ljca_spi_info spi_info;
+	};
+};
+
+typedef void (*ljca_event_cb_t)(struct platform_device *pdev, u8 cmd,
+				const void *evt_data, int len);
+
+int ljca_register_event_cb(struct platform_device *pdev,
+			   ljca_event_cb_t event_cb);
+void ljca_unregister_event_cb(struct platform_device *pdev);
+int ljca_transfer(struct platform_device *pdev, u8 cmd, const void *obuf,
+		  int obuf_len, void *ibuf, int *ibuf_len);
+int ljca_transfer_noack(struct platform_device *pdev, u8 cmd, const void *obuf,
+			int obuf_len);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mfd/stm32-lptimer.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mfd/stm32-lptimer.h
@@ -45,6 +45,11 @@
 #define STM32_LPTIM_PRESC	GENMASK(11, 9)
 #define STM32_LPTIM_CKPOL	GENMASK(2, 1)
 
+/* STM32_LPTIM_CKPOL */
+#define STM32_LPTIM_CKPOL_RISING_EDGE	0
+#define STM32_LPTIM_CKPOL_FALLING_EDGE	1
+#define STM32_LPTIM_CKPOL_BOTH_EDGES	2
+
 /* STM32_LPTIM_ARR */
 #define STM32_LPTIM_MAX_ARR	0xFFFF
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mfd/stm32-timers.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mfd/stm32-timers.h
@@ -82,6 +82,10 @@
 #define MAX_TIM_ICPSC		0x3
 #define TIM_CR2_MMS_SHIFT	4
 #define TIM_CR2_MMS2_SHIFT	20
+#define TIM_SMCR_SMS_SLAVE_MODE_DISABLED	0 /* counts on internal clock when CEN=1 */
+#define TIM_SMCR_SMS_ENCODER_MODE_1		1 /* counts TI1FP1 edges, depending on TI2FP2 level */
+#define TIM_SMCR_SMS_ENCODER_MODE_2		2 /* counts TI2FP2 edges, depending on TI1FP1 level */
+#define TIM_SMCR_SMS_ENCODER_MODE_3		3 /* counts on both TI1FP1 and TI2FP2 edges */
 #define TIM_SMCR_TS_SHIFT	4
 #define TIM_BDTR_BKF_MASK	0xF
 #define TIM_BDTR_BKF_SHIFT(x)	(16 + (x) * 4)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mfd/syscon/xlnx-vcu.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mfd/syscon/xlnx-vcu.h
@@ -36,4 +36,32 @@
 #define VCU_GASKET_INIT			0x74
 #define VCU_GASKET_VALUE		0x03
 
+/**
+ * struct xvcu_device - Xilinx VCU init device structure
+ * @dev: Platform device
+ * @pll_ref: pll ref clock source
+ * @reset_gpio: vcu reset gpio
+ * @aclk: axi clock source
+ * @logicore_reg_ba: logicore reg base address
+ * @vcu_slcr_ba: vcu_slcr Register base address
+ * @pll: handle for the VCU PLL
+ * @pll_post: handle for the VCU PLL post divider
+ * @clk_data: clocks provided by the vcu clock provider
+ */
+struct xvcu_device {
+	struct device *dev;
+	struct clk *pll_ref;
+	struct clk *aclk;
+	struct gpio_desc *reset_gpio;
+	struct regmap *logicore_reg_ba;
+	void __iomem *vcu_slcr_ba;
+	struct clk_hw *pll;
+	struct clk_hw *pll_post;
+	struct clk_hw_onecell_data *clk_data;
+};
+
+u32 xvcu_get_color_depth(struct xvcu_device *xvcu);
+u32 xvcu_get_memory_depth(struct xvcu_device *xvcu);
+u32 xvcu_get_clock_frequency(struct xvcu_device *xvcu);
+u32 xvcu_get_num_cores(struct xvcu_device *xvcu);
 #endif /* __XLNX_VCU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mfd/t7l66xb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mfd/t7l66xb.h
@@ -12,7 +12,6 @@
 
 struct t7l66xb_platform_data {
 	int (*enable)(struct platform_device *dev);
-	int (*disable)(struct platform_device *dev);
 	int (*suspend)(struct platform_device *dev);
 	int (*resume)(struct platform_device *dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mhi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mhi.h
@@ -664,6 +664,19 @@
 int mhi_pm_resume(struct mhi_controller *mhi_cntrl);
 
 /**
+ * mhi_pm_resume_force - Force resume MHI from suspended state
+ * @mhi_cntrl: MHI controller
+ *
+ * Resume the device irrespective of its MHI state. As per the MHI spec, devices
+ * has to be in M3 state during resume. But some devices seem to be in a
+ * different MHI state other than M3 but they continue working fine if allowed.
+ * This API is intented to be used for such devices.
+ *
+ * Return: 0 if the resume succeeds, a negative error code otherwise
+ */
+int mhi_pm_resume_force(struct mhi_controller *mhi_cntrl);
+
+/**
  * mhi_download_rddm_image - Download ramdump image from device for
  *                           debugging purpose.
  * @mhi_cntrl: MHI controller
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/micrel_phy.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/micrel_phy.h
@@ -37,9 +37,9 @@
 #define	PHY_ID_KSZ9477		0x00221631
 
 /* struct phy_device dev_flags definitions */
-#define MICREL_PHY_50MHZ_CLK	0x00000001
-#define MICREL_PHY_FXEN		0x00000002
-#define MICREL_KSZ8_P1_ERRATA	0x00000003
+#define MICREL_PHY_50MHZ_CLK	BIT(0)
+#define MICREL_PHY_FXEN		BIT(1)
+#define MICREL_KSZ8_P1_ERRATA	BIT(2)
 
 #define MICREL_KSZ9021_EXTREG_CTRL	0xB
 #define MICREL_KSZ9021_EXTREG_DATA_WRITE	0xC
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/minmax.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/minmax.h
@@ -2,54 +2,110 @@
 #ifndef _LINUX_MINMAX_H
 #define _LINUX_MINMAX_H
 
+#include <linux/build_bug.h>
+#include <linux/compiler.h>
 #include <linux/const.h>
 
 /*
  * min()/max()/clamp() macros must accomplish three things:
  *
- * - avoid multiple evaluations of the arguments (so side-effects like
+ * - Avoid multiple evaluations of the arguments (so side-effects like
  *   "x++" happen only once) when non-constant.
- * - perform strict type-checking (to generate warnings instead of
- *   nasty runtime surprises). See the "unnecessary" pointer comparison
- *   in __typecheck().
- * - retain result as a constant expressions when called with only
+ * - Retain result as a constant expressions when called with only
  *   constant expressions (to avoid tripping VLA warnings in stack
  *   allocation usage).
+ * - Perform signed v unsigned type-checking (to generate compile
+ *   errors instead of nasty runtime surprises).
+ * - Unsigned char/short are always promoted to signed int and can be
+ *   compared against signed or unsigned arguments.
+ * - Unsigned arguments can be compared against non-negative signed constants.
+ * - Comparison of a signed argument against an unsigned constant fails
+ *   even if the constant is below __INT_MAX__ and could be cast to int.
  */
 #define __typecheck(x, y) \
 	(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
 
-#define __no_side_effects(x, y) \
-		(__is_constexpr(x) && __is_constexpr(y))
+/* is_signed_type() isn't a constexpr for pointer types */
+#define __is_signed(x) 								\
+	__builtin_choose_expr(__is_constexpr(is_signed_type(typeof(x))),	\
+		is_signed_type(typeof(x)), 0)
+
+/* True for a non-negative signed int constant */
+#define __is_noneg_int(x)	\
+	(__builtin_choose_expr(__is_constexpr(x) && __is_signed(x), x, -1) >= 0)
+
+#define __types_ok(x, y) 					\
+	(__is_signed(x) == __is_signed(y) ||			\
+		__is_signed((x) + 0) == __is_signed((y) + 0) ||	\
+		__is_noneg_int(x) || __is_noneg_int(y))
 
-#define __safe_cmp(x, y) \
-		(__typecheck(x, y) && __no_side_effects(x, y))
+#define __cmp_op_min <
+#define __cmp_op_max >
 
-#define __cmp(x, y, op)	((x) op (y) ? (x) : (y))
+#define __cmp(op, x, y)	((x) __cmp_op_##op (y) ? (x) : (y))
 
-#define __cmp_once(x, y, unique_x, unique_y, op) ({	\
+#define __cmp_once(op, x, y, unique_x, unique_y) ({	\
 		typeof(x) unique_x = (x);		\
 		typeof(y) unique_y = (y);		\
-		__cmp(unique_x, unique_y, op); })
-
-#define __careful_cmp(x, y, op) \
-	__builtin_choose_expr(__safe_cmp(x, y), \
-		__cmp(x, y, op), \
-		__cmp_once(x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y), op))
+		static_assert(__types_ok(x, y),		\
+			#op "(" #x ", " #y ") signedness error, fix types or consider u" #op "() before " #op "_t()"); \
+		__cmp(op, unique_x, unique_y); })
+
+#define __careful_cmp(op, x, y)					\
+	__builtin_choose_expr(__is_constexpr((x) - (y)),	\
+		__cmp(op, x, y),				\
+		__cmp_once(op, x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y)))
+
+#define __clamp(val, lo, hi)	\
+	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
+
+#define __clamp_once(val, lo, hi, unique_val, unique_lo, unique_hi) ({	\
+		typeof(val) unique_val = (val);				\
+		typeof(lo) unique_lo = (lo);				\
+		typeof(hi) unique_hi = (hi);				\
+		static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
+				(lo) <= (hi), true),					\
+			"clamp() low limit " #lo " greater than high limit " #hi);	\
+		static_assert(__types_ok(val, lo), "clamp() 'lo' signedness error");	\
+		static_assert(__types_ok(val, hi), "clamp() 'hi' signedness error");	\
+		__clamp(unique_val, unique_lo, unique_hi); })
+
+#define __careful_clamp(val, lo, hi) ({					\
+	__builtin_choose_expr(__is_constexpr((val) - (lo) + (hi)),	\
+		__clamp(val, lo, hi),					\
+		__clamp_once(val, lo, hi, __UNIQUE_ID(__val),		\
+			     __UNIQUE_ID(__lo), __UNIQUE_ID(__hi))); })
 
 /**
  * min - return minimum of two values of the same or compatible types
  * @x: first value
  * @y: second value
  */
-#define min(x, y)	__careful_cmp(x, y, <)
+#define min(x, y)	__careful_cmp(min, x, y)
 
 /**
  * max - return maximum of two values of the same or compatible types
  * @x: first value
  * @y: second value
  */
-#define max(x, y)	__careful_cmp(x, y, >)
+#define max(x, y)	__careful_cmp(max, x, y)
+
+/**
+ * umin - return minimum of two non-negative values
+ *   Signed types are zero extended to match a larger unsigned type.
+ * @x: first value
+ * @y: second value
+ */
+#define umin(x, y)	\
+	__careful_cmp(min, (x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull)
+
+/**
+ * umax - return maximum of two non-negative values
+ * @x: first value
+ * @y: second value
+ */
+#define umax(x, y)	\
+	__careful_cmp(max, (x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull)
 
 /**
  * min3 - return minimum of three values
@@ -86,7 +142,7 @@
  * This macro does strict typechecking of @lo/@hi to make sure they are of the
  * same type as @val.  See the unnecessary pointer comparisons.
  */
-#define clamp(val, lo, hi) min((typeof(val))max(val, lo), hi)
+#define clamp(val, lo, hi) __careful_clamp(val, lo, hi)
 
 /*
  * ..and if you can't take the strict
@@ -101,7 +157,7 @@
  * @x: first value
  * @y: second value
  */
-#define min_t(type, x, y)	__careful_cmp((type)(x), (type)(y), <)
+#define min_t(type, x, y)	__careful_cmp(min, (type)(x), (type)(y))
 
 /**
  * max_t - return maximum of two values, using the specified type
@@ -109,7 +165,7 @@
  * @x: first value
  * @y: second value
  */
-#define max_t(type, x, y)	__careful_cmp((type)(x), (type)(y), >)
+#define max_t(type, x, y)	__careful_cmp(max, (type)(x), (type)(y))
 
 /**
  * clamp_t - return a value clamped to a given range using a given type
@@ -121,7 +177,7 @@
  * This macro does no typechecking and uses temporary variables of type
  * @type to make all the comparisons.
  */
-#define clamp_t(type, val, lo, hi) min_t(type, max_t(type, val, lo), hi)
+#define clamp_t(type, val, lo, hi) __careful_clamp((type)(val), (type)(lo), (type)(hi))
 
 /**
  * clamp_val - return a value clamped to a given range using val's type
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mlx5/device.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mlx5/device.h
@@ -454,6 +454,7 @@
 
 	MLX5_OPCODE_UMR			= 0x25,
 
+	MLX5_OPCODE_ACCESS_ASO		= 0x2d,
 };
 
 enum {
@@ -1075,6 +1076,11 @@
 };
 
 enum {
+	MLX5_VPORT_CVLAN_INSERT_WHEN_NO_CVLAN  = 0x1,
+	MLX5_VPORT_CVLAN_INSERT_ALWAYS         = 0x3,
+};
+
+enum {
 	MLX5_L3_PROT_TYPE_IPV4		= 0,
 	MLX5_L3_PROT_TYPE_IPV6		= 1,
 };
@@ -1099,6 +1105,7 @@
 	MLX5_MATCH_MISC_PARAMETERS_2	= 1 << 3,
 	MLX5_MATCH_MISC_PARAMETERS_3	= 1 << 4,
 	MLX5_MATCH_MISC_PARAMETERS_4	= 1 << 5,
+	MLX5_MATCH_MISC_PARAMETERS_5	= 1 << 6,
 };
 
 enum {
@@ -1456,6 +1463,8 @@
 	return MLX5_MIN_PKEY_TABLE_SIZE << pkey_sz;
 }
 
+#define MLX5_RDMA_RX_NUM_COUNTERS_PRIOS 2
+#define MLX5_RDMA_TX_NUM_COUNTERS_PRIOS 1
 #define MLX5_BY_PASS_NUM_REGULAR_PRIOS 16
 #define MLX5_BY_PASS_NUM_DONT_TRAP_PRIOS 16
 #define MLX5_BY_PASS_NUM_MULTICAST_PRIOS 1
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mlx5/driver.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mlx5/driver.h
@@ -364,7 +364,6 @@
 };
 
 struct mlx5_core_mkey {
-	u64			iova;
 	u64			size;
 	u32			key;
 	u32			pd;
@@ -686,7 +685,6 @@
 	struct timecounter         tc;
 	u32                        nominal_c_mult;
 	unsigned long              overflow_period;
-	struct delayed_work        overflow_work;
 };
 
 struct mlx5_clock {
@@ -759,6 +757,7 @@
 	enum mlx5_device_state	state;
 	/* sync interface state */
 	struct mutex		intf_state_mutex;
+	struct lock_class_key	lock_key;
 	unsigned long		intf_state;
 	struct mlx5_priv	priv;
 	struct mlx5_profile	profile;
@@ -965,7 +964,7 @@
 struct mlx5_async_ctx {
 	struct mlx5_core_dev *dev;
 	atomic_t num_inflight;
-	struct wait_queue_head wait;
+	struct completion inflight_done;
 };
 
 struct mlx5_async_work;
@@ -1181,6 +1180,12 @@
 	return dev->coredev_type == MLX5_COREDEV_VF;
 }
 
+static inline bool mlx5_core_same_coredev_type(const struct mlx5_core_dev *dev1,
+					       const struct mlx5_core_dev *dev2)
+{
+	return dev1->coredev_type == dev2->coredev_type;
+}
+
 static inline bool mlx5_core_is_ecpf(const struct mlx5_core_dev *dev)
 {
 	return dev->caps.embedded_cpu;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mlx5/eswitch.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mlx5/eswitch.h
@@ -136,13 +136,13 @@
 				       ESW_TUN_OPTS_SLOW_TABLE_GOTO_VPORT)
 #define ESW_TUN_SLOW_TABLE_GOTO_VPORT_MARK ESW_TUN_OPTS_MASK
 
-u8 mlx5_eswitch_mode(struct mlx5_core_dev *dev);
+u8 mlx5_eswitch_mode(const struct mlx5_core_dev *dev);
 u16 mlx5_eswitch_get_total_vports(const struct mlx5_core_dev *dev);
 struct mlx5_core_dev *mlx5_eswitch_get_core_dev(struct mlx5_eswitch *esw);
 
 #else  /* CONFIG_MLX5_ESWITCH */
 
-static inline u8 mlx5_eswitch_mode(struct mlx5_core_dev *dev)
+static inline u8 mlx5_eswitch_mode(const struct mlx5_core_dev *dev)
 {
 	return MLX5_ESWITCH_NONE;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mlx5/fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mlx5/fs.h
@@ -83,6 +83,8 @@
 	MLX5_FLOW_NAMESPACE_RDMA_RX,
 	MLX5_FLOW_NAMESPACE_RDMA_RX_KERNEL,
 	MLX5_FLOW_NAMESPACE_RDMA_TX,
+	MLX5_FLOW_NAMESPACE_RDMA_RX_COUNTERS,
+	MLX5_FLOW_NAMESPACE_RDMA_TX_COUNTERS,
 };
 
 enum {
@@ -97,6 +99,7 @@
 
 struct mlx5_pkt_reformat;
 struct mlx5_modify_hdr;
+struct mlx5_flow_definer;
 struct mlx5_flow_table;
 struct mlx5_flow_group;
 struct mlx5_flow_namespace;
@@ -257,6 +260,13 @@
 						 void *modify_actions);
 void mlx5_modify_header_dealloc(struct mlx5_core_dev *dev,
 				struct mlx5_modify_hdr *modify_hdr);
+struct mlx5_flow_definer *
+mlx5_create_match_definer(struct mlx5_core_dev *dev,
+			  enum mlx5_flow_namespace_type ns_type, u16 format_id,
+			  u32 *match_mask);
+void mlx5_destroy_match_definer(struct mlx5_core_dev *dev,
+				struct mlx5_flow_definer *definer);
+int mlx5_get_match_definer_id(struct mlx5_flow_definer *definer);
 
 struct mlx5_pkt_reformat_params {
 	int type;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mlx5/mlx5_ifc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mlx5/mlx5_ifc.h
@@ -94,6 +94,7 @@
 enum {
 	MLX5_OBJ_TYPE_GENEVE_TLV_OPT = 0x000b,
 	MLX5_OBJ_TYPE_VIRTIO_NET_Q = 0x000d,
+	MLX5_OBJ_TYPE_MATCH_DEFINER = 0x0018,
 	MLX5_OBJ_TYPE_MKEY = 0xff01,
 	MLX5_OBJ_TYPE_QP = 0xff02,
 	MLX5_OBJ_TYPE_PSV = 0xff03,
@@ -371,7 +372,8 @@
 	u8         reserved_at_37[0x9];
 
 	u8         geneve_tlv_option_0_data[0x1];
-	u8         reserved_at_41[0x4];
+	u8         geneve_tlv_option_0_exist[0x1];
+	u8         reserved_at_42[0x3];
 	u8         outer_first_mpls_over_udp[0x4];
 	u8         outer_first_mpls_over_gre[0x4];
 	u8         inner_first_mpls[0x4];
@@ -433,7 +435,9 @@
 	u8         max_modify_header_actions[0x8];
 	u8         max_ft_level[0x8];
 
-	u8         reserved_at_40[0x20];
+	u8         reserved_at_40[0x6];
+	u8         execute_aso[0x1];
+	u8         reserved_at_47[0x19];
 
 	u8         reserved_at_60[0x2];
 	u8         reformat_insert[0x1];
@@ -490,7 +494,10 @@
 	u8         tcp_sport[0x10];
 	u8         tcp_dport[0x10];
 
-	u8         reserved_at_c0[0x18];
+	u8         reserved_at_c0[0x10];
+	u8         ipv4_ihl[0x4];
+	u8         reserved_at_c4[0x4];
+
 	u8         ttl_hoplimit[0x8];
 
 	u8         udp_sport[0x10];
@@ -542,7 +549,8 @@
 	u8         reserved_at_b8[0x8];
 
 	u8         geneve_vni[0x18];
-	u8         reserved_at_d8[0x7];
+	u8         reserved_at_d8[0x6];
+	u8         geneve_tlv_option_0_exist[0x1];
 	u8         geneve_oam[0x1];
 
 	u8         reserved_at_e0[0xc];
@@ -661,6 +669,26 @@
 	u8         reserved_at_100[0x100];
 };
 
+struct mlx5_ifc_fte_match_set_misc5_bits {
+	u8         macsec_tag_0[0x20];
+
+	u8         macsec_tag_1[0x20];
+
+	u8         macsec_tag_2[0x20];
+
+	u8         macsec_tag_3[0x20];
+
+	u8         tunnel_header_0[0x20];
+
+	u8         tunnel_header_1[0x20];
+
+	u8         tunnel_header_2[0x20];
+
+	u8         tunnel_header_3[0x20];
+
+	u8         reserved_at_100[0x100];
+};
+
 struct mlx5_ifc_cmd_pas_bits {
 	u8         pa_h[0x20];
 
@@ -782,7 +810,7 @@
 	u8      fdb_to_vport_reg_c_id[0x8];
 	u8      reserved_at_8[0xd];
 	u8      fdb_modify_header_fwd_to_table[0x1];
-	u8      reserved_at_16[0x1];
+	u8      fdb_ipv4_ttl_modify[0x1];
 	u8      flow_source[0x1];
 	u8      reserved_at_18[0x2];
 	u8      multi_fdb_encap[0x1];
@@ -822,7 +850,8 @@
 	u8         vport_svlan_insert[0x1];
 	u8         vport_cvlan_insert_if_not_exist[0x1];
 	u8         vport_cvlan_insert_overwrite[0x1];
-	u8         reserved_at_5[0x2];
+	u8         reserved_at_5[0x1];
+	u8         vport_cvlan_insert_always[0x1];
 	u8         esw_shared_ingress_acl[0x1];
 	u8         esw_uplink_ingress_acl[0x1];
 	u8         root_ft_on_other_esw[0x1];
@@ -887,7 +916,18 @@
 
 	u8         max_tsar_bw_share[0x20];
 
-	u8         reserved_at_100[0x700];
+	u8         nic_element_type[0x10];
+	u8         nic_tsar_type[0x10];
+
+	u8         reserved_at_120[0x3];
+	u8         log_meter_aso_granularity[0x5];
+	u8         reserved_at_128[0x3];
+	u8         log_meter_aso_max_alloc[0x5];
+	u8         reserved_at_130[0x3];
+	u8         log_max_num_meter_aso[0x5];
+	u8         reserved_at_138[0x8];
+
+	u8         reserved_at_140[0x6c0];
 };
 
 struct mlx5_ifc_debug_cap_bits {
@@ -1262,7 +1302,7 @@
 enum {
 	MLX5_FLEX_PARSER_GENEVE_ENABLED		= 1 << 3,
 	MLX5_FLEX_PARSER_MPLS_OVER_GRE_ENABLED	= 1 << 4,
-	mlx5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED	= 1 << 5,
+	MLX5_FLEX_PARSER_MPLS_OVER_UDP_ENABLED	= 1 << 5,
 	MLX5_FLEX_PARSER_VXLAN_GPE_ENABLED	= 1 << 7,
 	MLX5_FLEX_PARSER_ICMP_V4_ENABLED	= 1 << 8,
 	MLX5_FLEX_PARSER_ICMP_V6_ENABLED	= 1 << 9,
@@ -1299,6 +1339,7 @@
 enum {
 	MLX5_STEERING_FORMAT_CONNECTX_5   = 0,
 	MLX5_STEERING_FORMAT_CONNECTX_6DX = 1,
+	MLX5_STEERING_FORMAT_CONNECTX_7   = 2,
 };
 
 struct mlx5_ifc_cmd_hca_cap_bits {
@@ -1512,7 +1553,9 @@
 	u8         rc[0x1];
 
 	u8         uar_4k[0x1];
-	u8         reserved_at_241[0x9];
+	u8         reserved_at_241[0x7];
+	u8         fl_rc_qp_when_roce_disabled[0x1];
+	u8         regexp_params[0x1];
 	u8         uar_sz[0x6];
 	u8         reserved_at_248[0x2];
 	u8         umem_uid_0[0x1];
@@ -1625,7 +1668,9 @@
 	u8         steering_format_version[0x4];
 	u8         create_qp_start_hint[0x18];
 
-	u8         reserved_at_460[0x3];
+	u8         reserved_at_460[0x1];
+	u8         ats[0x1];
+	u8         reserved_at_462[0x1];
 	u8         log_max_uctx[0x5];
 	u8         reserved_at_468[0x2];
 	u8         ipsec_offload[0x1];
@@ -1716,7 +1761,7 @@
 	u8         flex_parser_id_outer_first_mpls_over_gre[0x4];
 	u8         flex_parser_id_outer_first_mpls_over_udp_label[0x4];
 
-	u8	   reserved_at_6e0[0x10];
+	u8         max_num_match_definer[0x10];
 	u8	   sf_base_id[0x10];
 
 	u8         flex_parser_id_gtpu_dw_2[0x4];
@@ -1731,7 +1776,7 @@
 
 	u8	   reserved_at_760[0x20];
 	u8	   vhca_tunnel_commands[0x40];
-	u8	   reserved_at_7c0[0x40];
+	u8         match_definer_format_supported[0x40];
 };
 
 struct mlx5_ifc_cmd_hca_cap_2_bits {
@@ -1750,6 +1795,7 @@
 	MLX5_FLOW_DESTINATION_TYPE_FLOW_TABLE   = 0x1,
 	MLX5_FLOW_DESTINATION_TYPE_TIR          = 0x2,
 	MLX5_FLOW_DESTINATION_TYPE_FLOW_SAMPLER = 0x6,
+	MLX5_FLOW_DESTINATION_TYPE_UPLINK       = 0x8,
 
 	MLX5_FLOW_DESTINATION_TYPE_PORT         = 0x99,
 	MLX5_FLOW_DESTINATION_TYPE_COUNTER      = 0x100,
@@ -1804,7 +1850,9 @@
 
 	struct mlx5_ifc_fte_match_set_misc4_bits misc_parameters_4;
 
-	u8         reserved_at_c00[0x400];
+	struct mlx5_ifc_fte_match_set_misc5_bits misc_parameters_5;
+
+	u8         reserved_at_e00[0x200];
 };
 
 enum {
@@ -3152,6 +3200,7 @@
 	MLX5_FLOW_CONTEXT_ACTION_VLAN_PUSH_2 = 0x800,
 	MLX5_FLOW_CONTEXT_ACTION_IPSEC_DECRYPT = 0x1000,
 	MLX5_FLOW_CONTEXT_ACTION_IPSEC_ENCRYPT = 0x2000,
+	MLX5_FLOW_CONTEXT_ACTION_EXECUTE_ASO = 0x4000,
 };
 
 enum {
@@ -3167,6 +3216,38 @@
 	u8         vid[0xc];
 };
 
+enum {
+	MLX5_FLOW_METER_COLOR_RED	= 0x0,
+	MLX5_FLOW_METER_COLOR_YELLOW	= 0x1,
+	MLX5_FLOW_METER_COLOR_GREEN	= 0x2,
+	MLX5_FLOW_METER_COLOR_UNDEFINED	= 0x3,
+};
+
+enum {
+	MLX5_EXE_ASO_FLOW_METER		= 0x2,
+};
+
+struct mlx5_ifc_exe_aso_ctrl_flow_meter_bits {
+	u8        return_reg_id[0x4];
+	u8        aso_type[0x4];
+	u8        reserved_at_8[0x14];
+	u8        action[0x1];
+	u8        init_color[0x2];
+	u8        meter_id[0x1];
+};
+
+union mlx5_ifc_exe_aso_ctrl {
+	struct mlx5_ifc_exe_aso_ctrl_flow_meter_bits exe_aso_ctrl_flow_meter;
+};
+
+struct mlx5_ifc_execute_aso_bits {
+	u8        valid[0x1];
+	u8        reserved_at_1[0x7];
+	u8        aso_object_id[0x18];
+
+	union mlx5_ifc_exe_aso_ctrl exe_aso_ctrl;
+};
+
 struct mlx5_ifc_flow_context_bits {
 	struct mlx5_ifc_vlan_bits push_vlan;
 
@@ -3198,7 +3279,9 @@
 
 	struct mlx5_ifc_fte_match_param_bits match_value;
 
-	u8         reserved_at_1200[0x600];
+	struct mlx5_ifc_execute_aso_bits execute_aso[4];
+
+	u8         reserved_at_1300[0x500];
 
 	union mlx5_ifc_dest_format_struct_flow_counter_list_auto_bits destination[];
 };
@@ -3309,8 +3392,8 @@
 };
 
 enum {
-	MLX5_TIRC_LRO_ENABLE_MASK_IPV4_LRO  = 0x1,
-	MLX5_TIRC_LRO_ENABLE_MASK_IPV6_LRO  = 0x2,
+	MLX5_TIRC_PACKET_MERGE_MASK_IPV4_LRO  = BIT(0),
+	MLX5_TIRC_PACKET_MERGE_MASK_IPV6_LRO  = BIT(1),
 };
 
 enum {
@@ -3335,7 +3418,7 @@
 
 	u8         reserved_at_80[0x4];
 	u8         lro_timeout_period_usecs[0x10];
-	u8         lro_enable_mask[0x4];
+	u8         packet_merge_mask[0x4];
 	u8         lro_max_ip_payload_size[0x8];
 
 	u8         reserved_at_a0[0x40];
@@ -3470,6 +3553,7 @@
 	ELEMENT_TYPE_CAP_MASK_VPORT		= 1 << 1,
 	ELEMENT_TYPE_CAP_MASK_VPORT_TC		= 1 << 2,
 	ELEMENT_TYPE_CAP_MASK_PARA_VPORT_TC	= 1 << 3,
+	ELEMENT_TYPE_CAP_MASK_QUEUE_GROUP	= 1 << 4,
 };
 
 struct mlx5_ifc_scheduling_context_bits {
@@ -3645,7 +3729,9 @@
 	u8         lw[0x1];
 	u8         lr[0x1];
 	u8         access_mode_1_0[0x2];
-	u8         reserved_at_18[0x8];
+	u8         reserved_at_18[0x2];
+	u8         ma_translation_mode[0x2];
+	u8         reserved_at_1c[0x4];
 
 	u8         qpn[0x18];
 	u8         mkey_7_0[0x8];
@@ -4136,6 +4222,12 @@
 	TSAR_ELEMENT_TSAR_TYPE_ETS = 0x2,
 };
 
+enum {
+	TSAR_TYPE_CAP_MASK_DWRR		= 1 << 0,
+	TSAR_TYPE_CAP_MASK_ROUND_ROBIN	= 1 << 1,
+	TSAR_TYPE_CAP_MASK_ETS		= 1 << 2,
+};
+
 struct mlx5_ifc_tsar_element_bits {
 	u8         reserved_at_0[0x8];
 	u8         tsar_type[0x8];
@@ -5028,12 +5120,11 @@
 
 	u8         syndrome[0x20];
 
-	u8         reserved_at_40[0x20];
-	u8         ece[0x20];
+	u8         reserved_at_40[0x40];
 
 	u8         opt_param_mask[0x20];
 
-	u8         reserved_at_a0[0x20];
+	u8         ece[0x20];
 
 	struct mlx5_ifc_qpc_bits qpc;
 
@@ -5616,6 +5707,238 @@
 	u8         reserved_at_120[0xe0];
 };
 
+struct mlx5_ifc_match_definer_format_0_bits {
+	u8         reserved_at_0[0x100];
+
+	u8         metadata_reg_c_0[0x20];
+
+	u8         metadata_reg_c_1[0x20];
+
+	u8         outer_dmac_47_16[0x20];
+
+	u8         outer_dmac_15_0[0x10];
+	u8         outer_ethertype[0x10];
+
+	u8         reserved_at_180[0x1];
+	u8         sx_sniffer[0x1];
+	u8         functional_lb[0x1];
+	u8         outer_ip_frag[0x1];
+	u8         outer_qp_type[0x2];
+	u8         outer_encap_type[0x2];
+	u8         port_number[0x2];
+	u8         outer_l3_type[0x2];
+	u8         outer_l4_type[0x2];
+	u8         outer_first_vlan_type[0x2];
+	u8         outer_first_vlan_prio[0x3];
+	u8         outer_first_vlan_cfi[0x1];
+	u8         outer_first_vlan_vid[0xc];
+
+	u8         outer_l4_type_ext[0x4];
+	u8         reserved_at_1a4[0x2];
+	u8         outer_ipsec_layer[0x2];
+	u8         outer_l2_type[0x2];
+	u8         force_lb[0x1];
+	u8         outer_l2_ok[0x1];
+	u8         outer_l3_ok[0x1];
+	u8         outer_l4_ok[0x1];
+	u8         outer_second_vlan_type[0x2];
+	u8         outer_second_vlan_prio[0x3];
+	u8         outer_second_vlan_cfi[0x1];
+	u8         outer_second_vlan_vid[0xc];
+
+	u8         outer_smac_47_16[0x20];
+
+	u8         outer_smac_15_0[0x10];
+	u8         inner_ipv4_checksum_ok[0x1];
+	u8         inner_l4_checksum_ok[0x1];
+	u8         outer_ipv4_checksum_ok[0x1];
+	u8         outer_l4_checksum_ok[0x1];
+	u8         inner_l3_ok[0x1];
+	u8         inner_l4_ok[0x1];
+	u8         outer_l3_ok_duplicate[0x1];
+	u8         outer_l4_ok_duplicate[0x1];
+	u8         outer_tcp_cwr[0x1];
+	u8         outer_tcp_ece[0x1];
+	u8         outer_tcp_urg[0x1];
+	u8         outer_tcp_ack[0x1];
+	u8         outer_tcp_psh[0x1];
+	u8         outer_tcp_rst[0x1];
+	u8         outer_tcp_syn[0x1];
+	u8         outer_tcp_fin[0x1];
+};
+
+struct mlx5_ifc_match_definer_format_22_bits {
+	u8         reserved_at_0[0x100];
+
+	u8         outer_ip_src_addr[0x20];
+
+	u8         outer_ip_dest_addr[0x20];
+
+	u8         outer_l4_sport[0x10];
+	u8         outer_l4_dport[0x10];
+
+	u8         reserved_at_160[0x1];
+	u8         sx_sniffer[0x1];
+	u8         functional_lb[0x1];
+	u8         outer_ip_frag[0x1];
+	u8         outer_qp_type[0x2];
+	u8         outer_encap_type[0x2];
+	u8         port_number[0x2];
+	u8         outer_l3_type[0x2];
+	u8         outer_l4_type[0x2];
+	u8         outer_first_vlan_type[0x2];
+	u8         outer_first_vlan_prio[0x3];
+	u8         outer_first_vlan_cfi[0x1];
+	u8         outer_first_vlan_vid[0xc];
+
+	u8         metadata_reg_c_0[0x20];
+
+	u8         outer_dmac_47_16[0x20];
+
+	u8         outer_smac_47_16[0x20];
+
+	u8         outer_smac_15_0[0x10];
+	u8         outer_dmac_15_0[0x10];
+};
+
+struct mlx5_ifc_match_definer_format_23_bits {
+	u8         reserved_at_0[0x100];
+
+	u8         inner_ip_src_addr[0x20];
+
+	u8         inner_ip_dest_addr[0x20];
+
+	u8         inner_l4_sport[0x10];
+	u8         inner_l4_dport[0x10];
+
+	u8         reserved_at_160[0x1];
+	u8         sx_sniffer[0x1];
+	u8         functional_lb[0x1];
+	u8         inner_ip_frag[0x1];
+	u8         inner_qp_type[0x2];
+	u8         inner_encap_type[0x2];
+	u8         port_number[0x2];
+	u8         inner_l3_type[0x2];
+	u8         inner_l4_type[0x2];
+	u8         inner_first_vlan_type[0x2];
+	u8         inner_first_vlan_prio[0x3];
+	u8         inner_first_vlan_cfi[0x1];
+	u8         inner_first_vlan_vid[0xc];
+
+	u8         tunnel_header_0[0x20];
+
+	u8         inner_dmac_47_16[0x20];
+
+	u8         inner_smac_47_16[0x20];
+
+	u8         inner_smac_15_0[0x10];
+	u8         inner_dmac_15_0[0x10];
+};
+
+struct mlx5_ifc_match_definer_format_29_bits {
+	u8         reserved_at_0[0xc0];
+
+	u8         outer_ip_dest_addr[0x80];
+
+	u8         outer_ip_src_addr[0x80];
+
+	u8         outer_l4_sport[0x10];
+	u8         outer_l4_dport[0x10];
+
+	u8         reserved_at_1e0[0x20];
+};
+
+struct mlx5_ifc_match_definer_format_30_bits {
+	u8         reserved_at_0[0xa0];
+
+	u8         outer_ip_dest_addr[0x80];
+
+	u8         outer_ip_src_addr[0x80];
+
+	u8         outer_dmac_47_16[0x20];
+
+	u8         outer_smac_47_16[0x20];
+
+	u8         outer_smac_15_0[0x10];
+	u8         outer_dmac_15_0[0x10];
+};
+
+struct mlx5_ifc_match_definer_format_31_bits {
+	u8         reserved_at_0[0xc0];
+
+	u8         inner_ip_dest_addr[0x80];
+
+	u8         inner_ip_src_addr[0x80];
+
+	u8         inner_l4_sport[0x10];
+	u8         inner_l4_dport[0x10];
+
+	u8         reserved_at_1e0[0x20];
+};
+
+struct mlx5_ifc_match_definer_format_32_bits {
+	u8         reserved_at_0[0xa0];
+
+	u8         inner_ip_dest_addr[0x80];
+
+	u8         inner_ip_src_addr[0x80];
+
+	u8         inner_dmac_47_16[0x20];
+
+	u8         inner_smac_47_16[0x20];
+
+	u8         inner_smac_15_0[0x10];
+	u8         inner_dmac_15_0[0x10];
+};
+
+struct mlx5_ifc_match_definer_bits {
+	u8         modify_field_select[0x40];
+
+	u8         reserved_at_40[0x40];
+
+	u8         reserved_at_80[0x10];
+	u8         format_id[0x10];
+
+	u8         reserved_at_a0[0x160];
+
+	u8         match_mask[16][0x20];
+};
+
+struct mlx5_ifc_general_obj_in_cmd_hdr_bits {
+	u8         opcode[0x10];
+	u8         uid[0x10];
+
+	u8         vhca_tunnel_id[0x10];
+	u8         obj_type[0x10];
+
+	u8         obj_id[0x20];
+
+	u8         reserved_at_60[0x3];
+	u8         log_obj_range[0x5];
+	u8         reserved_at_68[0x18];
+};
+
+struct mlx5_ifc_general_obj_out_cmd_hdr_bits {
+	u8         status[0x8];
+	u8         reserved_at_8[0x18];
+
+	u8         syndrome[0x20];
+
+	u8         obj_id[0x20];
+
+	u8         reserved_at_60[0x20];
+};
+
+struct mlx5_ifc_create_match_definer_in_bits {
+	struct mlx5_ifc_general_obj_in_cmd_hdr_bits general_obj_in_cmd_hdr;
+
+	struct mlx5_ifc_match_definer_bits obj_context;
+};
+
+struct mlx5_ifc_create_match_definer_out_bits {
+	struct mlx5_ifc_general_obj_out_cmd_hdr_bits general_obj_out_cmd_hdr;
+};
+
 enum {
 	MLX5_QUERY_FLOW_GROUP_OUT_MATCH_CRITERIA_ENABLE_OUTER_HEADERS    = 0x0,
 	MLX5_QUERY_FLOW_GROUP_OUT_MATCH_CRITERIA_ENABLE_MISC_PARAMETERS  = 0x1,
@@ -5623,6 +5946,7 @@
 	MLX5_QUERY_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_MISC_PARAMETERS_2 = 0x3,
 	MLX5_QUERY_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_MISC_PARAMETERS_3 = 0x4,
 	MLX5_QUERY_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_MISC_PARAMETERS_4 = 0x5,
+	MLX5_QUERY_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_MISC_PARAMETERS_5 = 0x6,
 };
 
 struct mlx5_ifc_query_flow_group_out_bits {
@@ -6369,7 +6693,7 @@
 	u8         reserved_at_3c[0x1];
 	u8         hash[0x1];
 	u8         reserved_at_3e[0x1];
-	u8         lro[0x1];
+	u8         packet_merge[0x1];
 };
 
 struct mlx5_ifc_modify_tir_out_bits {
@@ -8090,6 +8414,11 @@
 };
 
 enum {
+	MLX5_CREATE_FLOW_GROUP_IN_GROUP_TYPE_TCAM_SUBTABLE  = 0x0,
+	MLX5_CREATE_FLOW_GROUP_IN_GROUP_TYPE_HASH_SPLIT     = 0x1,
+};
+
+enum {
 	MLX5_CREATE_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_OUTER_HEADERS     = 0x0,
 	MLX5_CREATE_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_MISC_PARAMETERS   = 0x1,
 	MLX5_CREATE_FLOW_GROUP_IN_MATCH_CRITERIA_ENABLE_INNER_HEADERS     = 0x2,
@@ -8110,7 +8439,9 @@
 	u8         reserved_at_60[0x20];
 
 	u8         table_type[0x8];
-	u8         reserved_at_88[0x18];
+	u8         reserved_at_88[0x4];
+	u8         group_type[0x4];
+	u8         reserved_at_90[0x10];
 
 	u8         reserved_at_a0[0x8];
 	u8         table_id[0x18];
@@ -8125,7 +8456,10 @@
 
 	u8         end_flow_index[0x20];
 
-	u8         reserved_at_140[0xa0];
+	u8         reserved_at_140[0x10];
+	u8         match_definer_id[0x10];
+
+	u8         reserved_at_160[0x80];
 
 	u8         reserved_at_1e0[0x18];
 	u8         match_criteria_enable[0x8];
@@ -8508,7 +8842,8 @@
 	u8         reserved_at_20[0x10];
 	u8         op_mod[0x10];
 
-	u8         reserved_at_40[0x38];
+	u8         reserved_at_40[0x33];
+	u8         flow_counter_bulk_log_size[0x5];
 	u8         flow_counter_bulk[0x8];
 };
 
@@ -9508,8 +9843,8 @@
 	u8         reserved_at_0[0x6];
 	u8         lossy[0x1];
 	u8         epsb[0x1];
-	u8         reserved_at_8[0xc];
-	u8         size[0xc];
+	u8         reserved_at_8[0x8];
+	u8         size[0x10];
 
 	u8         xoff_threshold[0x10];
 	u8         xon_threshold[0x10];
@@ -10614,33 +10949,11 @@
 	u8         reserved_at_40[0x40];
 };
 
-struct mlx5_ifc_general_obj_in_cmd_hdr_bits {
-	u8         opcode[0x10];
-	u8         uid[0x10];
-
-	u8         vhca_tunnel_id[0x10];
-	u8         obj_type[0x10];
-
-	u8         obj_id[0x20];
-
-	u8         reserved_at_60[0x20];
-};
-
-struct mlx5_ifc_general_obj_out_cmd_hdr_bits {
-	u8         status[0x8];
-	u8         reserved_at_8[0x18];
-
-	u8         syndrome[0x20];
-
-	u8         obj_id[0x20];
-
-	u8         reserved_at_60[0x20];
-};
-
 struct mlx5_ifc_umem_bits {
 	u8         reserved_at_0[0x80];
 
-	u8         reserved_at_80[0x1b];
+	u8         ats[0x1];
+	u8         reserved_at_81[0x1a];
 	u8         log_page_size[0x5];
 
 	u8         page_offset[0x20];
@@ -10969,12 +11282,14 @@
 	MLX5_HCA_CAP_GENERAL_OBJECT_TYPES_ENCRYPTION_KEY = BIT_ULL(0xc),
 	MLX5_HCA_CAP_GENERAL_OBJECT_TYPES_IPSEC = BIT_ULL(0x13),
 	MLX5_HCA_CAP_GENERAL_OBJECT_TYPES_SAMPLER = BIT_ULL(0x20),
+	MLX5_HCA_CAP_GENERAL_OBJECT_TYPES_FLOW_METER_ASO = BIT_ULL(0x24),
 };
 
 enum {
 	MLX5_GENERAL_OBJECT_TYPES_ENCRYPTION_KEY = 0xc,
 	MLX5_GENERAL_OBJECT_TYPES_IPSEC = 0x13,
 	MLX5_GENERAL_OBJECT_TYPES_SAMPLER = 0x20,
+	MLX5_GENERAL_OBJECT_TYPES_FLOW_METER_ASO = 0x24,
 };
 
 enum {
@@ -11049,6 +11364,61 @@
 	struct mlx5_ifc_encryption_key_obj_bits encryption_key_object;
 };
 
+enum {
+	MLX5_FLOW_METER_MODE_BYTES_IP_LENGTH		= 0x0,
+	MLX5_FLOW_METER_MODE_BYTES_CALC_WITH_L2		= 0x1,
+	MLX5_FLOW_METER_MODE_BYTES_CALC_WITH_L2_IPG	= 0x2,
+	MLX5_FLOW_METER_MODE_NUM_PACKETS		= 0x3,
+};
+
+struct mlx5_ifc_flow_meter_parameters_bits {
+	u8         valid[0x1];
+	u8         bucket_overflow[0x1];
+	u8         start_color[0x2];
+	u8         both_buckets_on_green[0x1];
+	u8         reserved_at_5[0x1];
+	u8         meter_mode[0x2];
+	u8         reserved_at_8[0x18];
+
+	u8         reserved_at_20[0x20];
+
+	u8         reserved_at_40[0x3];
+	u8         cbs_exponent[0x5];
+	u8         cbs_mantissa[0x8];
+	u8         reserved_at_50[0x3];
+	u8         cir_exponent[0x5];
+	u8         cir_mantissa[0x8];
+
+	u8         reserved_at_60[0x20];
+
+	u8         reserved_at_80[0x3];
+	u8         ebs_exponent[0x5];
+	u8         ebs_mantissa[0x8];
+	u8         reserved_at_90[0x3];
+	u8         eir_exponent[0x5];
+	u8         eir_mantissa[0x8];
+
+	u8         reserved_at_a0[0x60];
+};
+
+struct mlx5_ifc_flow_meter_aso_obj_bits {
+	u8         modify_field_select[0x40];
+
+	u8         reserved_at_40[0x40];
+
+	u8         reserved_at_80[0x8];
+	u8         meter_aso_access_pd[0x18];
+
+	u8         reserved_at_a0[0x160];
+
+	struct mlx5_ifc_flow_meter_parameters_bits flow_meter_parameters[2];
+};
+
+struct mlx5_ifc_create_flow_meter_aso_obj_in_bits {
+	struct mlx5_ifc_general_obj_in_cmd_hdr_bits hdr;
+	struct mlx5_ifc_flow_meter_aso_obj_bits flow_meter_aso_obj;
+};
+
 struct mlx5_ifc_sampler_obj_bits {
 	u8         modify_field_select[0x40];
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mlx5/qp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mlx5/qp.h
@@ -261,7 +261,10 @@
 	union {
 		struct {
 			__be16 sz;
-			u8     start[2];
+			union {
+				u8     start[2];
+				DECLARE_FLEX_ARRAY(u8, data);
+			};
 		} inline_hdr;
 		struct {
 			__be16 type;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mm.h
@@ -1511,11 +1511,18 @@
 
 static inline void page_kasan_tag_set(struct page *page, u8 tag)
 {
-	if (kasan_enabled()) {
-		tag ^= 0xff;
-		page->flags &= ~(KASAN_TAG_MASK << KASAN_TAG_PGSHIFT);
-		page->flags |= (tag & KASAN_TAG_MASK) << KASAN_TAG_PGSHIFT;
-	}
+	unsigned long old_flags, flags;
+
+	if (!kasan_enabled())
+		return;
+
+	tag ^= 0xff;
+	old_flags = READ_ONCE(page->flags);
+	do {
+		flags = old_flags;
+		flags &= ~(KASAN_TAG_MASK << KASAN_TAG_PGSHIFT);
+		flags |= (tag & KASAN_TAG_MASK) << KASAN_TAG_PGSHIFT;
+	} while (unlikely(!try_cmpxchg(&page->flags, &old_flags, flags)));
 }
 
 static inline void page_kasan_tag_reset(struct page *page)
@@ -1806,6 +1813,28 @@
 	unmap_mapping_range(mapping, holebegin, holelen, 0);
 }
 
+extern void vma_do_file_update_time(struct vm_area_struct *, const char[], int);
+extern struct file *vma_do_pr_or_file(struct vm_area_struct *, const char[],
+				      int);
+extern void vma_do_get_file(struct vm_area_struct *, const char[], int);
+extern void vma_do_fput(struct vm_area_struct *, const char[], int);
+
+#define vma_file_update_time(vma)	vma_do_file_update_time(vma, __func__, \
+								__LINE__)
+#define vma_pr_or_file(vma)		vma_do_pr_or_file(vma, __func__, \
+							  __LINE__)
+#define vma_get_file(vma)		vma_do_get_file(vma, __func__, __LINE__)
+#define vma_fput(vma)			vma_do_fput(vma, __func__, __LINE__)
+
+#ifndef CONFIG_MMU
+extern struct file *vmr_do_pr_or_file(struct vm_region *, const char[], int);
+extern void vmr_do_fput(struct vm_region *, const char[], int);
+
+#define vmr_pr_or_file(region)		vmr_do_pr_or_file(region, __func__, \
+							  __LINE__)
+#define vmr_fput(region)		vmr_do_fput(region, __func__, __LINE__)
+#endif /* !CONFIG_MMU */
+
 extern int access_process_vm(struct task_struct *tsk, unsigned long addr,
 		void *buf, int len, unsigned int gup_flags);
 extern int access_remote_vm(struct mm_struct *mm, unsigned long addr,
@@ -2447,7 +2476,7 @@
  * unsigned long max_zone_pfns[MAX_NR_ZONES] = {max_dma, max_normal_pfn,
  * 							 max_highmem_pfn};
  * for_each_valid_physical_page_range()
- * 	memblock_add_node(base, size, nid)
+ *	memblock_add_node(base, size, nid, MEMBLOCK_NONE)
  * free_area_init(max_zone_pfns);
  */
 void free_area_init(unsigned long *max_zone_pfn);
@@ -2600,6 +2629,7 @@
 				   unsigned long flags, struct page **pages);
 
 unsigned long randomize_stack_top(unsigned long stack_top);
+unsigned long randomize_page(unsigned long start, unsigned long range);
 
 extern unsigned long get_unmapped_area(struct file *, unsigned long, unsigned long, unsigned long, unsigned long);
 
@@ -2851,7 +2881,8 @@
 #define FOLL_FORCE	0x10	/* get_user_pages read/write w/o permission */
 #define FOLL_NOWAIT	0x20	/* if a disk transfer is needed, start the IO
 				 * and return without waiting upon it */
-#define FOLL_POPULATE	0x40	/* fault in page */
+#define FOLL_POPULATE	0x40	/* fault in pages (with FOLL_MLOCK) */
+#define FOLL_NOFAULT	0x80	/* do not fault in pages */
 #define FOLL_HWPOISON	0x100	/* check page is hwpoisoned */
 #define FOLL_NUMA	0x200	/* force NUMA hinting page fault */
 #define FOLL_MIGRATION	0x400	/* wait for page to replace migration entry */
@@ -3115,7 +3146,6 @@
 	MF_SOFT_OFFLINE = 1 << 3,
 };
 extern int memory_failure(unsigned long pfn, int flags);
-extern void memory_failure_queue(unsigned long pfn, int flags);
 extern void memory_failure_queue_kick(int cpu);
 extern int unpoison_memory(unsigned long pfn);
 extern int sysctl_memory_failure_early_kill;
@@ -3123,6 +3153,18 @@
 extern void shake_page(struct page *p);
 extern atomic_long_t num_poisoned_pages __read_mostly;
 extern int soft_offline_page(unsigned long pfn, int flags);
+#ifdef CONFIG_MEMORY_FAILURE
+extern void memory_failure_queue(unsigned long pfn, int flags);
+extern int __get_huge_page_for_hwpoison(unsigned long pfn, int flags);
+#else
+static inline void memory_failure_queue(unsigned long pfn, int flags)
+{
+}
+static inline int __get_huge_page_for_hwpoison(unsigned long pfn, int flags)
+{
+	return 0;
+}
+#endif
 
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mm_types.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mm_types.h
@@ -294,6 +294,7 @@
 	unsigned long	vm_top;		/* region allocated to here */
 	unsigned long	vm_pgoff;	/* the offset in vm_file corresponding to vm_start */
 	struct file	*vm_file;	/* the backing file or NULL */
+	struct file	*vm_prfile;	/* the virtual backing file or NULL */
 
 	int		vm_usage;	/* region usage count (access under nommu_region_sem) */
 	bool		vm_icache_flushed : 1; /* true if the icache has been flushed for
@@ -373,6 +374,7 @@
 	unsigned long vm_pgoff;		/* Offset (within vm_file) in PAGE_SIZE
 					   units */
 	struct file * vm_file;		/* File we map to (can be NULL). */
+	struct file *vm_prfile;		/* shadow of vm_file */
 	void * vm_private_data;		/* was vm_pte (shared mem) */
 
 #ifdef CONFIG_SWAP
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mman.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mman.h
@@ -2,6 +2,7 @@
 #ifndef _LINUX_MMAN_H
 #define _LINUX_MMAN_H
 
+#include <linux/fs.h>
 #include <linux/mm.h>
 #include <linux/percpu_counter.h>
 
@@ -90,7 +91,7 @@
 #endif
 
 #ifndef arch_calc_vm_flag_bits
-#define arch_calc_vm_flag_bits(flags) 0
+#define arch_calc_vm_flag_bits(file, flags) 0
 #endif
 
 #ifndef arch_vm_get_page_prot
@@ -151,12 +152,12 @@
  * Combine the mmap "flags" argument into "vm_flags" used internally.
  */
 static inline unsigned long
-calc_vm_flag_bits(unsigned long flags)
+calc_vm_flag_bits(struct file *file, unsigned long flags)
 {
 	return _calc_vm_trans(flags, MAP_GROWSDOWN,  VM_GROWSDOWN ) |
 	       _calc_vm_trans(flags, MAP_LOCKED,     VM_LOCKED    ) |
 	       _calc_vm_trans(flags, MAP_SYNC,	     VM_SYNC      ) |
-	       arch_calc_vm_flag_bits(flags);
+	       arch_calc_vm_flag_bits(file, flags);
 }
 
 unsigned long vm_commit_limit(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mmc/card.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mmc/card.h
@@ -292,6 +292,7 @@
 #define MMC_QUIRK_BROKEN_IRQ_POLLING	(1<<11)	/* Polling SDIO_CCCR_INTx could create a fake interrupt */
 #define MMC_QUIRK_TRIM_BROKEN	(1<<12)		/* Skip trim */
 #define MMC_QUIRK_BROKEN_HPI	(1<<13)		/* Disable broken HPI support */
+#define MMC_QUIRK_BROKEN_SD_DISCARD	(1<<14)	/* Disable broken SD discard support */
 
 	bool			reenable_cmdq;	/* Re-enable Command Queue */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mmc/host.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mmc/host.h
@@ -428,6 +428,7 @@
 	unsigned int		retune_paused:1; /* re-tuning is temporarily disabled */
 	unsigned int		retune_crc_disable:1; /* don't trigger retune upon crc */
 	unsigned int		can_dma_map_merge:1; /* merging can be used */
+	unsigned int		vqmmc_enabled:1; /* vqmmc regulator is enabled */
 
 	int			rescan_disable;	/* disable card detection */
 	int			rescan_entered;	/* used with nonremovable devices */
@@ -574,6 +575,8 @@
 #endif
 
 int mmc_regulator_get_supply(struct mmc_host *mmc);
+int mmc_regulator_enable_vqmmc(struct mmc_host *mmc);
+void mmc_regulator_disable_vqmmc(struct mmc_host *mmc);
 
 static inline int mmc_card_is_removable(struct mmc_host *host)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mmc/mmc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mmc/mmc.h
@@ -445,7 +445,7 @@
 #define MMC_SECURE_TRIM1_ARG		0x80000001
 #define MMC_SECURE_TRIM2_ARG		0x80008000
 #define MMC_SECURE_ARGS			0x80000000
-#define MMC_TRIM_ARGS			0x00008001
+#define MMC_TRIM_OR_DISCARD_ARGS	0x00008003
 
 #define mmc_driver_type_mask(n)		(1 << (n))
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mmc/slot-gpio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mmc/slot-gpio.h
@@ -20,6 +20,7 @@
 			 unsigned int debounce);
 int mmc_gpiod_request_ro(struct mmc_host *host, const char *con_id,
 			 unsigned int idx, unsigned int debounce);
+int mmc_gpiod_set_cd_config(struct mmc_host *host, unsigned long config);
 void mmc_gpio_set_cd_isr(struct mmc_host *host,
 			 irqreturn_t (*isr)(int irq, void *dev_id));
 int mmc_gpio_set_cd_wake(struct mmc_host *host, bool on);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mmzone.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mmzone.h
@@ -1031,6 +1031,15 @@
 #endif
 }
 
+#ifdef CONFIG_ZONE_DMA
+bool has_managed_dma(void);
+#else
+static inline bool has_managed_dma(void)
+{
+	return false;
+}
+#endif
+
 /**
  * is_highmem - helper function to quickly check if a struct zone is a
  *              highmem zone or not.  This is an attempt to keep references
@@ -1278,6 +1287,7 @@
 #define SUBSECTION_ALIGN_DOWN(pfn) ((pfn) & PAGE_SUBSECTION_MASK)
 
 struct mem_section_usage {
+	struct rcu_head rcu;
 #ifdef CONFIG_SPARSEMEM_VMEMMAP
 	DECLARE_BITMAP(subsection_map, SUBSECTIONS_PER_SECTION);
 #endif
@@ -1342,13 +1352,16 @@
 
 static inline struct mem_section *__nr_to_section(unsigned long nr)
 {
+	unsigned long root = SECTION_NR_TO_ROOT(nr);
+
+	if (unlikely(root >= NR_SECTION_ROOTS))
+		return NULL;
+
 #ifdef CONFIG_SPARSEMEM_EXTREME
-	if (!mem_section)
+	if (!mem_section || !mem_section[root])
 		return NULL;
 #endif
-	if (!mem_section[SECTION_NR_TO_ROOT(nr)])
-		return NULL;
-	return &mem_section[SECTION_NR_TO_ROOT(nr)][nr & SECTION_ROOT_MASK];
+	return &mem_section[root][nr & SECTION_ROOT_MASK];
 }
 extern size_t mem_section_usage_size(void);
 
@@ -1444,8 +1457,9 @@
 static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
 {
 	int idx = subsection_map_index(pfn);
+	struct mem_section_usage *usage = READ_ONCE(ms->usage);
 
-	return test_bit(idx, ms->usage->subsection_map);
+	return usage ? test_bit(idx, usage->subsection_map) : 0;
 }
 #else
 static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
@@ -1469,6 +1483,7 @@
 static inline int pfn_valid(unsigned long pfn)
 {
 	struct mem_section *ms;
+	int ret;
 
 	/*
 	 * Ensure the upper PAGE_SHIFT bits are clear in the
@@ -1481,14 +1496,20 @@
 
 	if (pfn_to_section_nr(pfn) >= NR_MEM_SECTIONS)
 		return 0;
-	ms = __nr_to_section(pfn_to_section_nr(pfn));
-	if (!valid_section(ms))
+	ms = __pfn_to_section(pfn);
+	rcu_read_lock();
+	if (!valid_section(ms)) {
+		rcu_read_unlock();
 		return 0;
+	}
 	/*
 	 * Traditionally early sections always returned pfn_valid() for
 	 * the entire section-sized span.
 	 */
-	return early_section(ms) || pfn_section_valid(ms, pfn);
+	ret = early_section(ms) || pfn_section_valid(ms, pfn);
+	rcu_read_unlock();
+
+	return ret;
 }
 #endif
 
@@ -1496,7 +1517,7 @@
 {
 	if (pfn_to_section_nr(pfn) >= NR_MEM_SECTIONS)
 		return 0;
-	return present_section(__nr_to_section(pfn_to_section_nr(pfn)));
+	return present_section(__pfn_to_section(pfn));
 }
 
 static inline unsigned long next_present_section_nr(unsigned long section_nr)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mnt_idmapping.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mnt_idmapping.h
@@ -0,0 +1,234 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_MNT_IDMAPPING_H
+#define _LINUX_MNT_IDMAPPING_H
+
+#include <linux/types.h>
+#include <linux/uidgid.h>
+
+struct user_namespace;
+/*
+ * Carries the initial idmapping of 0:0:4294967295 which is an identity
+ * mapping. This means that {g,u}id 0 is mapped to {g,u}id 0, {g,u}id 1 is
+ * mapped to {g,u}id 1, [...], {g,u}id 1000 to {g,u}id 1000, [...].
+ */
+extern struct user_namespace init_user_ns;
+
+/**
+ * initial_idmapping - check whether this is the initial mapping
+ * @ns: idmapping to check
+ *
+ * Check whether this is the initial mapping, mapping 0 to 0, 1 to 1,
+ * [...], 1000 to 1000 [...].
+ *
+ * Return: true if this is the initial mapping, false if not.
+ */
+static inline bool initial_idmapping(const struct user_namespace *ns)
+{
+	return ns == &init_user_ns;
+}
+
+/**
+ * no_idmapping - check whether we can skip remapping a kuid/gid
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ *
+ * This function can be used to check whether a remapping between two
+ * idmappings is required.
+ * An idmapped mount is a mount that has an idmapping attached to it that
+ * is different from the filsystem's idmapping and the initial idmapping.
+ * If the initial mapping is used or the idmapping of the mount and the
+ * filesystem are identical no remapping is required.
+ *
+ * Return: true if remapping can be skipped, false if not.
+ */
+static inline bool no_idmapping(const struct user_namespace *mnt_userns,
+				const struct user_namespace *fs_userns)
+{
+	return initial_idmapping(mnt_userns) || mnt_userns == fs_userns;
+}
+
+/**
+ * mapped_kuid_fs - map a filesystem kuid into a mnt_userns
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ * @kuid : kuid to be mapped
+ *
+ * Take a @kuid and remap it from @fs_userns into @mnt_userns. Use this
+ * function when preparing a @kuid to be reported to userspace.
+ *
+ * If no_idmapping() determines that this is not an idmapped mount we can
+ * simply return @kuid unchanged.
+ * If initial_idmapping() tells us that the filesystem is not mounted with an
+ * idmapping we know the value of @kuid won't change when calling
+ * from_kuid() so we can simply retrieve the value via __kuid_val()
+ * directly.
+ *
+ * Return: @kuid mapped according to @mnt_userns.
+ * If @kuid has no mapping in either @mnt_userns or @fs_userns INVALID_UID is
+ * returned.
+ */
+static inline kuid_t mapped_kuid_fs(struct user_namespace *mnt_userns,
+				    struct user_namespace *fs_userns,
+				    kuid_t kuid)
+{
+	uid_t uid;
+
+	if (no_idmapping(mnt_userns, fs_userns))
+		return kuid;
+	if (initial_idmapping(fs_userns))
+		uid = __kuid_val(kuid);
+	else
+		uid = from_kuid(fs_userns, kuid);
+	if (uid == (uid_t)-1)
+		return INVALID_UID;
+	return make_kuid(mnt_userns, uid);
+}
+
+/**
+ * mapped_kgid_fs - map a filesystem kgid into a mnt_userns
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ * @kgid : kgid to be mapped
+ *
+ * Take a @kgid and remap it from @fs_userns into @mnt_userns. Use this
+ * function when preparing a @kgid to be reported to userspace.
+ *
+ * If no_idmapping() determines that this is not an idmapped mount we can
+ * simply return @kgid unchanged.
+ * If initial_idmapping() tells us that the filesystem is not mounted with an
+ * idmapping we know the value of @kgid won't change when calling
+ * from_kgid() so we can simply retrieve the value via __kgid_val()
+ * directly.
+ *
+ * Return: @kgid mapped according to @mnt_userns.
+ * If @kgid has no mapping in either @mnt_userns or @fs_userns INVALID_GID is
+ * returned.
+ */
+static inline kgid_t mapped_kgid_fs(struct user_namespace *mnt_userns,
+				    struct user_namespace *fs_userns,
+				    kgid_t kgid)
+{
+	gid_t gid;
+
+	if (no_idmapping(mnt_userns, fs_userns))
+		return kgid;
+	if (initial_idmapping(fs_userns))
+		gid = __kgid_val(kgid);
+	else
+		gid = from_kgid(fs_userns, kgid);
+	if (gid == (gid_t)-1)
+		return INVALID_GID;
+	return make_kgid(mnt_userns, gid);
+}
+
+/**
+ * mapped_kuid_user - map a user kuid into a mnt_userns
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ * @kuid : kuid to be mapped
+ *
+ * Use the idmapping of @mnt_userns to remap a @kuid into @fs_userns. Use this
+ * function when preparing a @kuid to be written to disk or inode.
+ *
+ * If no_idmapping() determines that this is not an idmapped mount we can
+ * simply return @kuid unchanged.
+ * If initial_idmapping() tells us that the filesystem is not mounted with an
+ * idmapping we know the value of @kuid won't change when calling
+ * make_kuid() so we can simply retrieve the value via KUIDT_INIT()
+ * directly.
+ *
+ * Return: @kuid mapped according to @mnt_userns.
+ * If @kuid has no mapping in either @mnt_userns or @fs_userns INVALID_UID is
+ * returned.
+ */
+static inline kuid_t mapped_kuid_user(struct user_namespace *mnt_userns,
+				      struct user_namespace *fs_userns,
+				      kuid_t kuid)
+{
+	uid_t uid;
+
+	if (no_idmapping(mnt_userns, fs_userns))
+		return kuid;
+	uid = from_kuid(mnt_userns, kuid);
+	if (uid == (uid_t)-1)
+		return INVALID_UID;
+	if (initial_idmapping(fs_userns))
+		return KUIDT_INIT(uid);
+	return make_kuid(fs_userns, uid);
+}
+
+/**
+ * mapped_kgid_user - map a user kgid into a mnt_userns
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ * @kgid : kgid to be mapped
+ *
+ * Use the idmapping of @mnt_userns to remap a @kgid into @fs_userns. Use this
+ * function when preparing a @kgid to be written to disk or inode.
+ *
+ * If no_idmapping() determines that this is not an idmapped mount we can
+ * simply return @kgid unchanged.
+ * If initial_idmapping() tells us that the filesystem is not mounted with an
+ * idmapping we know the value of @kgid won't change when calling
+ * make_kgid() so we can simply retrieve the value via KGIDT_INIT()
+ * directly.
+ *
+ * Return: @kgid mapped according to @mnt_userns.
+ * If @kgid has no mapping in either @mnt_userns or @fs_userns INVALID_GID is
+ * returned.
+ */
+static inline kgid_t mapped_kgid_user(struct user_namespace *mnt_userns,
+				      struct user_namespace *fs_userns,
+				      kgid_t kgid)
+{
+	gid_t gid;
+
+	if (no_idmapping(mnt_userns, fs_userns))
+		return kgid;
+	gid = from_kgid(mnt_userns, kgid);
+	if (gid == (gid_t)-1)
+		return INVALID_GID;
+	if (initial_idmapping(fs_userns))
+		return KGIDT_INIT(gid);
+	return make_kgid(fs_userns, gid);
+}
+
+/**
+ * mapped_fsuid - return caller's fsuid mapped up into a mnt_userns
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ *
+ * Use this helper to initialize a new vfs or filesystem object based on
+ * the caller's fsuid. A common example is initializing the i_uid field of
+ * a newly allocated inode triggered by a creation event such as mkdir or
+ * O_CREAT. Other examples include the allocation of quotas for a specific
+ * user.
+ *
+ * Return: the caller's current fsuid mapped up according to @mnt_userns.
+ */
+static inline kuid_t mapped_fsuid(struct user_namespace *mnt_userns,
+				  struct user_namespace *fs_userns)
+{
+	return mapped_kuid_user(mnt_userns, fs_userns, current_fsuid());
+}
+
+/**
+ * mapped_fsgid - return caller's fsgid mapped up into a mnt_userns
+ * @mnt_userns: the mount's idmapping
+ * @fs_userns: the filesystem's idmapping
+ *
+ * Use this helper to initialize a new vfs or filesystem object based on
+ * the caller's fsgid. A common example is initializing the i_gid field of
+ * a newly allocated inode triggered by a creation event such as mkdir or
+ * O_CREAT. Other examples include the allocation of quotas for a specific
+ * user.
+ *
+ * Return: the caller's current fsgid mapped up according to @mnt_userns.
+ */
+static inline kgid_t mapped_fsgid(struct user_namespace *mnt_userns,
+				  struct user_namespace *fs_userns)
+{
+	return mapped_kgid_user(mnt_userns, fs_userns, current_fsgid());
+}
+
+#endif /* _LINUX_MNT_IDMAPPING_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mnt_namespace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mnt_namespace.h
@@ -7,12 +7,15 @@
 struct fs_struct;
 struct user_namespace;
 struct ns_common;
+struct vfsmount;
 
 extern struct mnt_namespace *copy_mnt_ns(unsigned long, struct mnt_namespace *,
 		struct user_namespace *, struct fs_struct *);
 extern void put_mnt_ns(struct mnt_namespace *ns);
 extern struct ns_common *from_mnt_ns(struct mnt_namespace *);
 
+extern int is_current_mnt_ns(struct vfsmount *mnt);
+
 extern const struct file_operations proc_mounts_operations;
 extern const struct file_operations proc_mountinfo_operations;
 extern const struct file_operations proc_mountstats_operations;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mod_devicetable.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mod_devicetable.h
@@ -676,6 +676,8 @@
 	__u16 model;
 	__u16 steppings;
 	__u16 feature;	/* bit index */
+	/* Solely for kernel-internal use: DO NOT EXPORT to userspace! */
+	__u16 flags;
 	kernel_ulong_t driver_data;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/module.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/module.h
@@ -595,9 +595,9 @@
 /* Look for this name: can be of form module:name. */
 unsigned long module_kallsyms_lookup_name(const char *name);
 
-extern void __noreturn __module_put_and_exit(struct module *mod,
+extern void __noreturn __module_put_and_kthread_exit(struct module *mod,
 			long code);
-#define module_put_and_exit(code) __module_put_and_exit(THIS_MODULE, code)
+#define module_put_and_kthread_exit(code) __module_put_and_kthread_exit(THIS_MODULE, code)
 
 #ifdef CONFIG_MODULE_UNLOAD
 int module_refcount(struct module *mod);
@@ -790,7 +790,7 @@
 	return 0;
 }
 
-#define module_put_and_exit(code) do_exit(code)
+#define module_put_and_kthread_exit(code) kthread_exit(code)
 
 static inline void print_modules(void)
 {
@@ -867,8 +867,17 @@
 }
 #endif	/* CONFIG_MODULE_SIG */
 
+#if defined(CONFIG_MODULES) && defined(CONFIG_KALLSYMS)
 int module_kallsyms_on_each_symbol(int (*fn)(void *, const char *,
 					     struct module *, unsigned long),
 				   void *data);
+#else
+static inline int module_kallsyms_on_each_symbol(int (*fn)(void *, const char *,
+						 struct module *, unsigned long),
+						 void *data)
+{
+	return -EOPNOTSUPP;
+}
+#endif  /* CONFIG_MODULES && CONFIG_KALLSYMS */
 
 #endif /* _LINUX_MODULE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/moduleloader.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/moduleloader.h
@@ -39,6 +39,11 @@
  */
 bool module_exit_section(const char *name);
 
+/* Describes whether within_module_init() will consider this an init section
+ * or not. This behaviour changes with CONFIG_MODULE_UNLOAD.
+ */
+bool module_init_layout_section(const char *sname);
+
 /*
  * Apply the given relocation to the (simplified) ELF.  Return -error
  * or 0.
@@ -90,6 +95,14 @@
 		    const Elf_Shdr *sechdrs,
 		    struct module *mod);
 
+#ifdef CONFIG_MODULES
+void flush_module_init_free_work(void);
+#else
+static inline void flush_module_init_free_work(void)
+{
+}
+#endif
+
 /* Any cleanup needed when module leaves. */
 void module_arch_cleanup(struct module *mod);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mroute.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mroute.h
@@ -17,7 +17,7 @@
 }
 
 int ip_mroute_setsockopt(struct sock *, int, sockptr_t, unsigned int);
-int ip_mroute_getsockopt(struct sock *, int, char __user *, int __user *);
+int ip_mroute_getsockopt(struct sock *, int, sockptr_t, sockptr_t);
 int ipmr_ioctl(struct sock *sk, int cmd, void __user *arg);
 int ipmr_compat_ioctl(struct sock *sk, unsigned int cmd, void __user *arg);
 int ip_mr_init(void);
@@ -29,8 +29,8 @@
 	return -ENOPROTOOPT;
 }
 
-static inline int ip_mroute_getsockopt(struct sock *sock, int optname,
-				       char __user *optval, int __user *optlen)
+static inline int ip_mroute_getsockopt(struct sock *sk, int optname,
+				       sockptr_t optval, sockptr_t optlen)
 {
 	return -ENOPROTOOPT;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/msi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/msi.h
@@ -148,7 +148,7 @@
 				u8	is_msix		: 1;
 				u8	multiple	: 3;
 				u8	multi_cap	: 3;
-				u8	maskbit		: 1;
+				u8	can_mask	: 1;
 				u8	is_64		: 1;
 				u8	is_virtual	: 1;
 				u16	entry_nr;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mtd/cfi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mtd/cfi.h
@@ -286,6 +286,7 @@
 	map_word sector_erase_cmd;
 	unsigned long chipshift; /* Because they're of the same type */
 	const char *im_name;	 /* inter_module name for cmdset_setup */
+	unsigned long quirks;
 	struct flchip chips[];  /* per-chip data structure for each chip */
 };
 
@@ -373,6 +374,7 @@
 #define CFI_MFR_MICRON		0x002C /* Micron */
 #define CFI_MFR_TOSHIBA		0x0098
 #define CFI_MFR_WINBOND		0x00DA
+#define CFI_MFR_WINBND		0x00EF /* Winbond */
 
 void cfi_fixup(struct mtd_info *mtd, struct cfi_fixup* fixups);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mtd/hyperbus.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mtd/hyperbus.h
@@ -89,9 +89,7 @@
 /**
  * hyperbus_unregister_device - deregister HyperBus slave memory device
  * @hbdev: hyperbus_device to be unregistered
- *
- * Return: 0 for success, others for failure.
  */
-int hyperbus_unregister_device(struct hyperbus_device *hbdev);
+void hyperbus_unregister_device(struct hyperbus_device *hbdev);
 
 #endif /* __LINUX_MTD_HYPERBUS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mtd/mtd.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mtd/mtd.h
@@ -73,7 +73,8 @@
 };
 
 #define MTD_MAX_OOBFREE_ENTRIES_LARGE	32
-#define MTD_MAX_ECCPOS_ENTRIES_LARGE	640
+#define MTD_MAX_ECCPOS_ENTRIES_LARGE	1260
+
 /**
  * struct mtd_oob_region - oob region definition
  * @offset: region offset
@@ -394,10 +395,8 @@
 	/* List of partitions attached to this MTD device */
 	struct list_head partitions;
 
-	union {
-		struct mtd_part part;
-		struct mtd_master master;
-	};
+	struct mtd_part part;
+	struct mtd_master master;
 };
 
 static inline struct mtd_info *mtd_get_master(struct mtd_info *mtd)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mtd/onfi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mtd/onfi.h
@@ -172,6 +172,7 @@
  * @nvddr_timing_modes: Supported source synchronous/NV-DDR timing modes
  * @vendor_revision: Vendor specific revision number
  * @vendor: Vendor specific data
+ * @jedec_id: jedec id of the flash
  */
 struct onfi_params {
 	int version;
@@ -184,6 +185,7 @@
 	u16 nvddr_timing_modes;
 	u16 vendor_revision;
 	u8 vendor[88];
+	u8 jedec_id;
 };
 
 #endif /* __LINUX_MTD_ONFI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mtd/rawnand.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mtd/rawnand.h
@@ -1240,6 +1240,7 @@
  * @lock: Lock protecting the suspended field. Also used to serialize accesses
  *        to the NAND device
  * @suspended: Set to 1 when the device is suspended, 0 when it's not
+ * @resume_wq: wait queue to sleep if rawnand is in suspended state.
  * @cur_cs: Currently selected target. -1 means no target selected, otherwise we
  *          should always have cur_cs >= 0 && cur_cs < nanddev_ntargets().
  *          NAND Controller drivers should not modify this value, but they're
@@ -1294,6 +1295,7 @@
 	/* Internals */
 	struct mutex lock;
 	unsigned int suspended : 1;
+	wait_queue_head_t resume_wq;
 	int cur_cs;
 	int read_retries;
 	struct nand_secure_region *secure_regions;
@@ -1539,6 +1541,8 @@
 		      bool force_8bit, bool check_only);
 int nand_write_data_op(struct nand_chip *chip, const void *buf,
 		       unsigned int len, bool force_8bit);
+int nand_read_page_hwecc_oob_first(struct nand_chip *chip, uint8_t *buf,
+				   int oob_required, int page);
 
 /* Scan and identify a NAND device */
 int nand_scan_with_ids(struct nand_chip *chip, unsigned int max_chips,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mtd/spi-nor.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mtd/spi-nor.h
@@ -51,6 +51,7 @@
 #define SPINOR_OP_CLFSR		0x50	/* Clear flag status register */
 #define SPINOR_OP_RDEAR		0xc8	/* Read Extended Address Register */
 #define SPINOR_OP_WREAR		0xc5	/* Write Extended Address Register */
+#define SPINOR_OP_WRCR		0x81	/* Write Configuration register */
 #define SPINOR_OP_SRSTEN	0x66	/* Software Reset Enable */
 #define SPINOR_OP_SRST		0x99	/* Software Reset */
 #define SPINOR_OP_GBULK		0x98    /* Global Block Unlock */
@@ -86,6 +87,7 @@
 #define SPINOR_OP_BP		0x02	/* Byte program */
 #define SPINOR_OP_AAI_WP	0xad	/* Auto address increment word program */
 
+#define GLOBAL_BLKPROT_UNLK	0x98	/* Clear global write protection bits */
 /* Used for S3AN flashes only */
 #define SPINOR_OP_XSE		0x50	/* Sector erase */
 #define SPINOR_OP_XPP		0x82	/* Page program */
@@ -101,6 +103,7 @@
 
 /* Used for Spansion flashes only. */
 #define SPINOR_OP_BRWR		0x17	/* Bank register write */
+#define SPINOR_OP_BRRD		0x16	/* Bank register read */
 #define SPINOR_OP_CLSR		0x30	/* Clear status register 1 */
 
 /* Used for Micron flashes only. */
@@ -119,11 +122,18 @@
 #define SR_BP0			BIT(2)	/* Block protect 0 */
 #define SR_BP1			BIT(3)	/* Block protect 1 */
 #define SR_BP2			BIT(4)	/* Block protect 2 */
-#define SR_BP3			BIT(5)	/* Block protect 3 */
+#define SR_BP_BIT_OFFSET	2	/* Offset to Block protect 0 */
+#define SR_BP_BIT_MASK		(SR_BP2 | SR_BP1 | SR_BP0)
+#define SR_BP3			BIT(6)	/* Block protect 3 */
 #define SR_TB_BIT5		BIT(5)	/* Top/Bottom protect */
 #define SR_BP3_BIT6		BIT(6)	/* Block protect 3 */
+#define SR_BP3_BIT5		BIT(5)	/* Block protect 3 */
 #define SR_TB_BIT6		BIT(6)	/* Top/Bottom protect */
 #define SR_SRWD			BIT(7)	/* SR write protect */
+/* Bit to determine whether protection starts from top or bottom */
+#define SR_BP_TB		0x20
+#define BP_BITS_FROM_SR(sr)	(((sr) & SR_BP_BIT_MASK) >> SR_BP_BIT_OFFSET)
+#define M25P_MAX_LOCKABLE_SECTORS	64
 /* Spansion/Cypress specific status bits */
 #define SR_E_ERR		BIT(5)
 #define SR_P_ERR		BIT(6)
@@ -141,6 +151,8 @@
 #define FSR_P_ERR		BIT(4)	/* Program operation status */
 #define FSR_PT_ERR		BIT(1)	/* Protection error bit */
 
+/* Extended/Bank Address Register bits */
+#define EAR_SEGMENT_MASK	0x7 /* 128 Mb segment mask */
 /* Status Register 2 bits. */
 #define SR2_QUAD_EN_BIT1	BIT(1)
 #define SR2_LB1			BIT(3)	/* Security Register Lock Bit 1 */
@@ -399,6 +411,7 @@
 	struct spi_mem		*spimem;
 	u8			*bouncebuf;
 	size_t			bouncebuf_size;
+	struct spi_device       *spi;
 	const struct flash_info	*info;
 	const struct spi_nor_manufacturer *manufacturer;
 	u32			page_size;
@@ -407,11 +420,19 @@
 	u8			read_opcode;
 	u8			read_dummy;
 	u8			program_opcode;
+	u32			jedec_id;
+	u16			curbank;
+	u16			n_sectors;
+	u32			sector_size;
 	enum spi_nor_protocol	read_proto;
 	enum spi_nor_protocol	write_proto;
 	enum spi_nor_protocol	reg_proto;
 	bool			sst_write_second;
 	u32			flags;
+	bool			shift;
+	bool			isparallel;
+	bool                    isstacked;
+	bool			is_lock;
 	enum spi_nor_cmd_ext	cmd_ext_type;
 	struct sfdp		*sfdp;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/mutex.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/mutex.h
@@ -20,6 +20,8 @@
 #include <linux/osq_lock.h>
 #include <linux/debug_locks.h>
 
+struct device;
+
 #ifdef CONFIG_DEBUG_LOCK_ALLOC
 # define __DEP_MAP_MUTEX_INITIALIZER(lockname)			\
 		, .dep_map = {					\
@@ -170,6 +172,31 @@
 } while (0)
 #endif /* CONFIG_PREEMPT_RT */
 
+#ifdef CONFIG_DEBUG_MUTEXES
+
+int __devm_mutex_init(struct device *dev, struct mutex *lock);
+
+#else
+
+static inline int __devm_mutex_init(struct device *dev, struct mutex *lock)
+{
+	/*
+	 * When CONFIG_DEBUG_MUTEXES is off mutex_destroy() is just a nop so
+	 * no really need to register it in the devm subsystem.
+	 */
+	return 0;
+}
+
+#endif
+
+#define devm_mutex_init(dev, mutex)			\
+({							\
+	typeof(mutex) mutex_ = (mutex);			\
+							\
+	mutex_init(mutex_);				\
+	__devm_mutex_init(dev, mutex_);			\
+})
+
 /*
  * See kernel/locking/mutex.c for detailed documentation of these APIs.
  * Also see Documentation/locking/mutex-design.rst.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/namei.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/namei.h
@@ -57,24 +57,39 @@
 	return user_path_at_empty(dfd, name, flags, path, NULL);
 }
 
+struct dentry *lookup_one_qstr_excl(const struct qstr *name,
+				    struct dentry *base,
+				    unsigned int flags);
 extern int kern_path(const char *, unsigned, struct path *);
 
 extern struct dentry *kern_path_create(int, const char *, struct path *, unsigned int);
 extern struct dentry *user_path_create(int, const char __user *, struct path *, unsigned int);
 extern void done_path_create(struct path *, struct dentry *);
 extern struct dentry *kern_path_locked(const char *, struct path *);
+int vfs_path_parent_lookup(struct filename *filename, unsigned int flags,
+			   struct path *parent, struct qstr *last, int *type,
+			   const struct path *root);
+int vfs_path_lookup(struct dentry *, struct vfsmount *, const char *,
+		    unsigned int, struct path *);
 
 extern struct dentry *try_lookup_one_len(const char *, struct dentry *, int);
 extern struct dentry *lookup_one_len(const char *, struct dentry *, int);
 extern struct dentry *lookup_one_len_unlocked(const char *, struct dentry *, int);
 extern struct dentry *lookup_positive_unlocked(const char *, struct dentry *, int);
 struct dentry *lookup_one(struct user_namespace *, const char *, struct dentry *, int);
+struct dentry *lookup_one_unlocked(struct user_namespace *mnt_userns,
+				   const char *name, struct dentry *base,
+				   int len);
+struct dentry *lookup_one_positive_unlocked(struct user_namespace *mnt_userns,
+					    const char *name,
+					    struct dentry *base, int len);
 
 extern int follow_down_one(struct path *);
 extern int follow_down(struct path *);
 extern int follow_up(struct path *);
 
 extern struct dentry *lock_rename(struct dentry *, struct dentry *);
+extern struct dentry *lock_rename_child(struct dentry *, struct dentry *);
 extern void unlock_rename(struct dentry *, struct dentry *);
 
 extern int __must_check nd_jump_link(struct path *path);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netdev_features.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netdev_features.h
@@ -169,7 +169,7 @@
 #define NETIF_F_HW_HSR_FWD	__NETIF_F(HW_HSR_FWD)
 #define NETIF_F_HW_HSR_DUP	__NETIF_F(HW_HSR_DUP)
 
-/* Finds the next feature with the highest number of the range of start till 0.
+/* Finds the next feature with the highest number of the range of start-1 till 0.
  */
 static inline int find_next_netdev_feature(u64 feature, unsigned long start)
 {
@@ -188,7 +188,7 @@
 	for ((bit) = find_next_netdev_feature((mask_addr),		\
 					      NETDEV_FEATURE_COUNT);	\
 	     (bit) >= 0;						\
-	     (bit) = find_next_netdev_feature((mask_addr), (bit) - 1))
+	     (bit) = find_next_netdev_feature((mask_addr), (bit)))
 
 /* Features valid for ethtool to change */
 /* = all defined minus driver/device-class-related */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netdevice.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netdevice.h
@@ -48,6 +48,7 @@
 #include <uapi/linux/pkt_cls.h>
 #include <linux/hashtable.h>
 #include <linux/rbtree.h>
+#include <linux/ref_tracker.h>
 
 struct netpoll_info;
 struct device;
@@ -167,31 +168,38 @@
  *	(unsigned long) so they can be read and written atomically.
  */
 
+#define NET_DEV_STAT(FIELD)			\
+	union {					\
+		unsigned long FIELD;		\
+		atomic_long_t __##FIELD;	\
+	}
+
 struct net_device_stats {
-	unsigned long	rx_packets;
-	unsigned long	tx_packets;
-	unsigned long	rx_bytes;
-	unsigned long	tx_bytes;
-	unsigned long	rx_errors;
-	unsigned long	tx_errors;
-	unsigned long	rx_dropped;
-	unsigned long	tx_dropped;
-	unsigned long	multicast;
-	unsigned long	collisions;
-	unsigned long	rx_length_errors;
-	unsigned long	rx_over_errors;
-	unsigned long	rx_crc_errors;
-	unsigned long	rx_frame_errors;
-	unsigned long	rx_fifo_errors;
-	unsigned long	rx_missed_errors;
-	unsigned long	tx_aborted_errors;
-	unsigned long	tx_carrier_errors;
-	unsigned long	tx_fifo_errors;
-	unsigned long	tx_heartbeat_errors;
-	unsigned long	tx_window_errors;
-	unsigned long	rx_compressed;
-	unsigned long	tx_compressed;
+	NET_DEV_STAT(rx_packets);
+	NET_DEV_STAT(tx_packets);
+	NET_DEV_STAT(rx_bytes);
+	NET_DEV_STAT(tx_bytes);
+	NET_DEV_STAT(rx_errors);
+	NET_DEV_STAT(tx_errors);
+	NET_DEV_STAT(rx_dropped);
+	NET_DEV_STAT(tx_dropped);
+	NET_DEV_STAT(multicast);
+	NET_DEV_STAT(collisions);
+	NET_DEV_STAT(rx_length_errors);
+	NET_DEV_STAT(rx_over_errors);
+	NET_DEV_STAT(rx_crc_errors);
+	NET_DEV_STAT(rx_frame_errors);
+	NET_DEV_STAT(rx_fifo_errors);
+	NET_DEV_STAT(rx_missed_errors);
+	NET_DEV_STAT(tx_aborted_errors);
+	NET_DEV_STAT(tx_carrier_errors);
+	NET_DEV_STAT(tx_fifo_errors);
+	NET_DEV_STAT(tx_heartbeat_errors);
+	NET_DEV_STAT(tx_window_errors);
+	NET_DEV_STAT(rx_compressed);
+	NET_DEV_STAT(tx_compressed);
 };
+#undef NET_DEV_STAT
 
 
 #include <linux/cache.h>
@@ -268,9 +276,11 @@
  * relationship HH alignment <= LL alignment.
  */
 #define LL_RESERVED_SPACE(dev) \
-	((((dev)->hard_header_len+(dev)->needed_headroom)&~(HH_DATA_MOD - 1)) + HH_DATA_MOD)
+	((((dev)->hard_header_len + READ_ONCE((dev)->needed_headroom)) \
+	  & ~(HH_DATA_MOD - 1)) + HH_DATA_MOD)
 #define LL_RESERVED_SPACE_EXTRA(dev,extra) \
-	((((dev)->hard_header_len+(dev)->needed_headroom+(extra))&~(HH_DATA_MOD - 1)) + HH_DATA_MOD)
+	((((dev)->hard_header_len + READ_ONCE((dev)->needed_headroom) + (extra)) \
+	  & ~(HH_DATA_MOD - 1)) + HH_DATA_MOD)
 
 struct header_ops {
 	int	(*create) (struct sk_buff *skb, struct net_device *dev,
@@ -300,6 +310,12 @@
 };
 
 
+#ifdef CONFIG_NET_DEV_REFCNT_TRACKER
+typedef struct ref_tracker *netdevice_tracker;
+#else
+typedef struct {} netdevice_tracker;
+#endif
+
 struct gro_list {
 	struct list_head	list;
 	int			count;
@@ -626,9 +642,23 @@
  */
 static inline bool net_has_fallback_tunnels(const struct net *net)
 {
-	return !IS_ENABLED(CONFIG_SYSCTL) ||
-	       !sysctl_fb_tunnels_only_for_init_net ||
-	       (net == &init_net && sysctl_fb_tunnels_only_for_init_net == 1);
+#if IS_ENABLED(CONFIG_SYSCTL)
+	int fb_tunnels_only_for_init_net = READ_ONCE(sysctl_fb_tunnels_only_for_init_net);
+
+	return !fb_tunnels_only_for_init_net ||
+		(net_eq(net, &init_net) && fb_tunnels_only_for_init_net == 1);
+#else
+	return true;
+#endif
+}
+
+static inline int net_inherit_devconf(void)
+{
+#if IS_ENABLED(CONFIG_SYSCTL)
+	return READ_ONCE(sysctl_devconf_inherit_init_net);
+#else
+	return 0;
+#endif
 }
 
 static inline int netdev_queue_numa_node_read(const struct netdev_queue *q)
@@ -714,8 +744,11 @@
 		/* We only give a hint, preemption can change CPU under us */
 		val |= raw_smp_processor_id();
 
-		if (table->ents[index] != val)
-			table->ents[index] = val;
+		/* The following WRITE_ONCE() is paired with the READ_ONCE()
+		 * here, and another one in get_rps_cpu().
+		 */
+		if (READ_ONCE(table->ents[index]) != val)
+			WRITE_ONCE(table->ents[index], val);
 	}
 }
 
@@ -887,7 +920,7 @@
 
 struct net_device_path_ctx {
 	const struct net_device *dev;
-	const u8		*daddr;
+	u8			daddr[ETH_ALEN];
 
 	int			num_vlans;
 	struct {
@@ -1645,7 +1678,7 @@
 	IFF_FAILOVER_SLAVE		= 1<<28,
 	IFF_L3MDEV_RX_HANDLER		= 1<<29,
 	IFF_LIVE_RENAME_OK		= 1<<30,
-	IFF_TX_SKB_NO_LINEAR		= 1<<31,
+	IFF_TX_SKB_NO_LINEAR		= BIT_ULL(31),
 };
 
 #define IFF_802_1Q_VLAN			IFF_802_1Q_VLAN
@@ -1814,7 +1847,6 @@
  *	@tipc_ptr:	TIPC specific data
  *	@atalk_ptr:	AppleTalk link
  *	@ip_ptr:	IPv4 specific data
- *	@dn_ptr:	DECnet specific data
  *	@ip6_ptr:	IPv6 specific data
  *	@ax25_ptr:	AX.25 specific data
  *	@ieee80211_ptr:	IEEE 802.11 specific data, assign before registering
@@ -1869,6 +1901,7 @@
  *	@proto_down_reason:	reason a netdev interface is held down
  *	@pcpu_refcnt:		Number of references to this device
  *	@dev_refcnt:		Number of references to this device
+ *	@refcnt_tracker:	Tracker directory for tracked references to this device
  *	@todo_list:		Delayed register/unregister
  *	@link_watch_list:	XXX: need comments on this one
  *
@@ -2097,9 +2130,6 @@
 	void 			*atalk_ptr;
 #endif
 	struct in_device __rcu	*ip_ptr;
-#if IS_ENABLED(CONFIG_DECNET)
-	struct dn_dev __rcu     *dn_ptr;
-#endif
 	struct inet6_dev __rcu	*ip6_ptr;
 #if IS_ENABLED(CONFIG_AX25)
 	void			*ax25_ptr;
@@ -2149,7 +2179,7 @@
 	struct netdev_queue	*_tx ____cacheline_aligned_in_smp;
 	unsigned int		num_tx_queues;
 	unsigned int		real_num_tx_queues;
-	struct Qdisc		*qdisc;
+	struct Qdisc __rcu	*qdisc;
 	unsigned int		tx_queue_len;
 	spinlock_t		tx_global_lock;
 
@@ -2178,6 +2208,7 @@
 #else
 	refcount_t		dev_refcnt;
 #endif
+	struct ref_tracker_dir	refcnt_tracker;
 
 	struct list_head	link_watch_list;
 
@@ -2433,6 +2464,12 @@
 }
 
 static inline
+struct net *dev_net_rcu(const struct net_device *dev)
+{
+	return read_pnet_rcu(&dev->nd_net);
+}
+
+static inline
 void dev_net_set(struct net_device *dev, struct net *net)
 {
 	write_pnet(&dev->nd_net, net);
@@ -2636,6 +2673,7 @@
 					      struct net_device *);
 	bool			(*id_match)(struct packet_type *ptype,
 					    struct sock *sk);
+	struct net		*af_packet_net;
 	void			*af_packet_priv;
 	struct list_head	list;
 };
@@ -2937,6 +2975,8 @@
 }
 
 int netdev_boot_setup_check(struct net_device *dev);
+struct net_device *dev_getbyhwaddr(struct net *net, unsigned short type,
+				   const char *hwaddr);
 struct net_device *dev_getbyhwaddr_rcu(struct net *net, unsigned short type,
 				       const char *hwaddr);
 struct net_device *dev_getfirstbyhwtype(struct net *net, unsigned short type);
@@ -2955,6 +2995,7 @@
 struct net_device *dev_get_by_name(struct net *net, const char *name);
 struct net_device *dev_get_by_name_rcu(struct net *net, const char *name);
 struct net_device *__dev_get_by_name(struct net *net, const char *name);
+bool netdev_name_in_use(struct net *net, const char *name);
 int dev_alloc_name(struct net_device *dev, const char *name);
 int dev_open(struct net_device *dev, struct netlink_ext_ack *extack);
 void dev_close(struct net_device *dev);
@@ -4155,6 +4196,7 @@
  *	@dev: network device
  *
  * Release reference to device to allow it to be freed.
+ * Try using dev_put_track() instead.
  */
 static inline void dev_put(struct net_device *dev)
 {
@@ -4172,6 +4214,7 @@
  *	@dev: network device
  *
  * Hold reference to device to keep it from being freed.
+ * Try using dev_hold_track() instead.
  */
 static inline void dev_hold(struct net_device *dev)
 {
@@ -4184,6 +4227,40 @@
 	}
 }
 
+static inline void netdev_tracker_alloc(struct net_device *dev,
+					netdevice_tracker *tracker, gfp_t gfp)
+{
+#ifdef CONFIG_NET_DEV_REFCNT_TRACKER
+	ref_tracker_alloc(&dev->refcnt_tracker, tracker, gfp);
+#endif
+}
+
+static inline void netdev_tracker_free(struct net_device *dev,
+				       netdevice_tracker *tracker)
+{
+#ifdef CONFIG_NET_DEV_REFCNT_TRACKER
+	ref_tracker_free(&dev->refcnt_tracker, tracker);
+#endif
+}
+
+static inline void dev_hold_track(struct net_device *dev,
+				  netdevice_tracker *tracker, gfp_t gfp)
+{
+	if (dev) {
+		dev_hold(dev);
+		netdev_tracker_alloc(dev, tracker, gfp);
+	}
+}
+
+static inline void dev_put_track(struct net_device *dev,
+				 netdevice_tracker *tracker)
+{
+	if (dev) {
+		netdev_tracker_free(dev, tracker);
+		dev_put(dev);
+	}
+}
+
 /* Carrier loss detection, dial on demand. The functions netif_carrier_on
  * and _off may be called from IRQ context, but it is caller
  * who is responsible for serialization of these calls.
@@ -4403,7 +4480,8 @@
 static inline void __netif_tx_lock(struct netdev_queue *txq, int cpu)
 {
 	spin_lock(&txq->_xmit_lock);
-	txq->xmit_lock_owner = cpu;
+	/* Pairs with READ_ONCE() in __dev_queue_xmit() */
+	WRITE_ONCE(txq->xmit_lock_owner, cpu);
 }
 
 static inline bool __netif_tx_acquire(struct netdev_queue *txq)
@@ -4420,26 +4498,32 @@
 static inline void __netif_tx_lock_bh(struct netdev_queue *txq)
 {
 	spin_lock_bh(&txq->_xmit_lock);
-	txq->xmit_lock_owner = smp_processor_id();
+	/* Pairs with READ_ONCE() in __dev_queue_xmit() */
+	WRITE_ONCE(txq->xmit_lock_owner, smp_processor_id());
 }
 
 static inline bool __netif_tx_trylock(struct netdev_queue *txq)
 {
 	bool ok = spin_trylock(&txq->_xmit_lock);
-	if (likely(ok))
-		txq->xmit_lock_owner = smp_processor_id();
+
+	if (likely(ok)) {
+		/* Pairs with READ_ONCE() in __dev_queue_xmit() */
+		WRITE_ONCE(txq->xmit_lock_owner, smp_processor_id());
+	}
 	return ok;
 }
 
 static inline void __netif_tx_unlock(struct netdev_queue *txq)
 {
-	txq->xmit_lock_owner = -1;
+	/* Pairs with READ_ONCE() in __dev_queue_xmit() */
+	WRITE_ONCE(txq->xmit_lock_owner, -1);
 	spin_unlock(&txq->_xmit_lock);
 }
 
 static inline void __netif_tx_unlock_bh(struct netdev_queue *txq)
 {
-	txq->xmit_lock_owner = -1;
+	/* Pairs with READ_ONCE() in __dev_queue_xmit() */
+	WRITE_ONCE(txq->xmit_lock_owner, -1);
 	spin_unlock_bh(&txq->_xmit_lock);
 }
 
@@ -5166,6 +5250,15 @@
 	return dev->priv_flags & IFF_L3MDEV_SLAVE;
 }
 
+static inline int dev_sdif(const struct net_device *dev)
+{
+#ifdef CONFIG_NET_L3_MASTER_DEV
+	if (netif_is_l3_slave(dev))
+		return dev->ifindex;
+#endif
+	return 0;
+}
+
 static inline bool netif_is_bridge_master(const struct net_device *dev)
 {
 	return dev->priv_flags & IFF_EBRIDGE;
@@ -5455,4 +5548,10 @@
 
 extern struct net_device *blackhole_netdev;
 
+/* Note: Avoid these macros in fast path, prefer per-cpu or per-queue counters. */
+#define DEV_STATS_INC(DEV, FIELD) atomic_long_inc(&(DEV)->stats.__##FIELD)
+#define DEV_STATS_ADD(DEV, FIELD, VAL) 	\
+		atomic_long_add((VAL), &(DEV)->stats.__##FIELD)
+#define DEV_STATS_READ(DEV, FIELD) atomic_long_read(&(DEV)->stats.__##FIELD)
+
 #endif	/* _LINUX_NETDEVICE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter.h
@@ -243,11 +243,6 @@
 		hook_head = rcu_dereference(net->nf.hooks_bridge[hook]);
 #endif
 		break;
-#if IS_ENABLED(CONFIG_DECNET)
-	case NFPROTO_DECNET:
-		hook_head = rcu_dereference(net->nf.hooks_decnet[hook]);
-		break;
-#endif
 	default:
 		WARN_ON_ONCE(1);
 		break;
@@ -381,13 +376,13 @@
 				  enum ip_conntrack_dir dir);
 };
 
-extern struct nf_nat_hook __rcu *nf_nat_hook;
+extern const struct nf_nat_hook __rcu *nf_nat_hook;
 
 static inline void
 nf_nat_decode_session(struct sk_buff *skb, struct flowi *fl, u_int8_t family)
 {
 #if IS_ENABLED(CONFIG_NF_NAT)
-	struct nf_nat_hook *nat_hook;
+	const struct nf_nat_hook *nat_hook;
 
 	rcu_read_lock();
 	nat_hook = rcu_dereference(nf_nat_hook);
@@ -440,13 +435,14 @@
 #if IS_ENABLED(CONFIG_NF_CONNTRACK)
 #include <linux/netfilter/nf_conntrack_zones_common.h>
 
-extern void (*ip_ct_attach)(struct sk_buff *, const struct sk_buff *) __rcu;
 void nf_ct_attach(struct sk_buff *, const struct sk_buff *);
+void nf_ct_set_closing(struct nf_conntrack *nfct);
 struct nf_conntrack_tuple;
 bool nf_ct_get_tuple_skb(struct nf_conntrack_tuple *dst_tuple,
 			 const struct sk_buff *skb);
 #else
 static inline void nf_ct_attach(struct sk_buff *new, struct sk_buff *skb) {}
+static inline void nf_ct_set_closing(struct nf_conntrack *nfct) {}
 struct nf_conntrack_tuple;
 static inline bool nf_ct_get_tuple_skb(struct nf_conntrack_tuple *dst_tuple,
 				       const struct sk_buff *skb)
@@ -463,8 +459,11 @@
 	void (*destroy)(struct nf_conntrack *);
 	bool (*get_tuple_skb)(struct nf_conntrack_tuple *,
 			      const struct sk_buff *);
+	void (*attach)(struct sk_buff *nskb, const struct sk_buff *skb);
+	void (*set_closing)(struct nf_conntrack *nfct);
+	int (*confirm)(struct sk_buff *skb);
 };
-extern struct nf_ct_hook __rcu *nf_ct_hook;
+extern const struct nf_ct_hook __rcu *nf_ct_hook;
 
 struct nlattr;
 
@@ -479,7 +478,7 @@
 	void (*seq_adjust)(struct sk_buff *skb, struct nf_conn *ct,
 			   enum ip_conntrack_info ctinfo, s32 off);
 };
-extern struct nfnl_ct_hook __rcu *nfnl_ct_hook;
+extern const struct nfnl_ct_hook __rcu *nfnl_ct_hook;
 
 /**
  * nf_skb_duplicated - TEE target has sent a packet
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter/ipset/ip_set.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter/ipset/ip_set.h
@@ -186,6 +186,8 @@
 	/* Return true if "b" set is the same as "a"
 	 * according to the create set parameters */
 	bool (*same_set)(const struct ip_set *a, const struct ip_set *b);
+	/* Cancel ongoing garbage collectors before destroying the set*/
+	void (*cancel_gc)(struct ip_set *set);
 	/* Region-locking is used */
 	bool region_lock;
 };
@@ -197,7 +199,7 @@
 };
 
 /* Max range where every element is added/deleted in one step */
-#define IPSET_MAX_RANGE		(1<<20)
+#define IPSET_MAX_RANGE		(1<<14)
 
 /* The max revision number supported by any set type + 1 */
 #define IPSET_REVISION_MAX	9
@@ -242,6 +244,8 @@
 
 /* A generic IP set */
 struct ip_set {
+	/* For call_cru in destroy */
+	struct rcu_head rcu;
 	/* The name of the set */
 	char name[IPSET_MAXNAMELEN];
 	/* Lock protecting the set data */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter/nf_conntrack_common.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter/nf_conntrack_common.h
@@ -2,7 +2,7 @@
 #ifndef _NF_CONNTRACK_COMMON_H
 #define _NF_CONNTRACK_COMMON_H
 
-#include <linux/atomic.h>
+#include <linux/refcount.h>
 #include <uapi/linux/netfilter/nf_conntrack_common.h>
 
 struct ip_conntrack_stat {
@@ -25,19 +25,21 @@
 #define NFCT_PTRMASK	~(NFCT_INFOMASK)
 
 struct nf_conntrack {
-	atomic_t use;
+	refcount_t use;
 };
 
 void nf_conntrack_destroy(struct nf_conntrack *nfct);
+
+/* like nf_ct_put, but without module dependency on nf_conntrack */
 static inline void nf_conntrack_put(struct nf_conntrack *nfct)
 {
-	if (nfct && atomic_dec_and_test(&nfct->use))
+	if (nfct && refcount_dec_and_test(&nfct->use))
 		nf_conntrack_destroy(nfct);
 }
 static inline void nf_conntrack_get(struct nf_conntrack *nfct)
 {
 	if (nfct)
-		atomic_inc(&nfct->use);
+		refcount_inc(&nfct->use);
 }
 
 #endif /* _NF_CONNTRACK_COMMON_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter/nf_conntrack_sctp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter/nf_conntrack_sctp.h
@@ -9,6 +9,7 @@
 	enum sctp_conntrack state;
 
 	__be32 vtag[IP_CT_DIR_MAX];
+	u8 init[IP_CT_DIR_MAX];
 	u8 last_dir;
 	u8 flags;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter/nfnetlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter/nfnetlink.h
@@ -45,7 +45,6 @@
 	int (*commit)(struct net *net, struct sk_buff *skb);
 	int (*abort)(struct net *net, struct sk_buff *skb,
 		     enum nfnl_abort_action action);
-	void (*cleanup)(struct net *net);
 	bool (*valid_genid)(struct net *net, u32 genid);
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter_bridge/ebtables.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter_bridge/ebtables.h
@@ -94,10 +94,6 @@
 	struct ebt_replace_kernel *table;
 	unsigned int valid_hooks;
 	rwlock_t lock;
-	/* e.g. could be the table explicitly only allows certain
-	 * matches, targets, ... 0 == let it in */
-	int (*check)(const struct ebt_table_info *info,
-	   unsigned int valid_hooks);
 	/* the data used by the kernel */
 	struct ebt_table_info *private;
 	struct nf_hook_ops *ops;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netfilter_defs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netfilter_defs.h
@@ -7,14 +7,6 @@
 /* in/out/forward only */
 #define NF_ARP_NUMHOOKS 3
 
-/* max hook is NF_DN_ROUTE (6), also see uapi/linux/netfilter_decnet.h */
-#define NF_DN_NUMHOOKS 7
-
-#if IS_ENABLED(CONFIG_DECNET)
-/* Largest hook number + 1, see uapi/linux/netfilter_decnet.h */
-#define NF_MAX_HOOKS	NF_DN_NUMHOOKS
-#else
 #define NF_MAX_HOOKS	NF_INET_NUMHOOKS
-#endif
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/netpoll.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/netpoll.h
@@ -70,7 +70,7 @@
 {
 	struct net_device *dev = napi->dev;
 
-	if (dev && dev->npinfo) {
+	if (dev && rcu_access_pointer(dev->npinfo)) {
 		int owner = smp_processor_id();
 
 		while (cmpxchg(&napi->poll_owner, -1, owner) != -1)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs.h
@@ -36,14 +36,6 @@
 	memcpy(target->data, source->data, source->size);
 }
 
-
-/*
- * This is really a general kernel constant, but since nothing like
- * this is defined in the kernel headers, I have to do it here.
- */
-#define NFS_OFFSET_MAX		((__s64)((~(__u64)0) >> 1))
-
-
 enum nfs3_stable_how {
 	NFS_UNSTABLE = 0,
 	NFS_DATA_SYNC = 1,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs4.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs4.h
@@ -292,6 +292,10 @@
 	NFS4ERR_XATTR2BIG      = 10096,
 };
 
+/* error codes for internal client use */
+#define NFS4ERR_RESET_TO_MDS   12001
+#define NFS4ERR_RESET_TO_PNFS  12002
+
 static inline bool seqid_mutating_err(u32 err)
 {
 	/* See RFC 7530, section 9.1.7 */
@@ -726,4 +730,17 @@
 	SETXATTR4_CREATE	= 1,
 	SETXATTR4_REPLACE	= 2,
 };
+
+enum {
+	RCA4_TYPE_MASK_RDATA_DLG	= 0,
+	RCA4_TYPE_MASK_WDATA_DLG	= 1,
+	RCA4_TYPE_MASK_DIR_DLG		= 2,
+	RCA4_TYPE_MASK_FILE_LAYOUT	= 3,
+	RCA4_TYPE_MASK_BLK_LAYOUT	= 4,
+	RCA4_TYPE_MASK_OBJ_LAYOUT_MIN	= 8,
+	RCA4_TYPE_MASK_OBJ_LAYOUT_MAX	= 9,
+	RCA4_TYPE_MASK_OTHER_LAYOUT_MIN	= 12,
+	RCA4_TYPE_MASK_OTHER_LAYOUT_MAX	= 15,
+};
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs_fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs_fs.h
@@ -62,6 +62,7 @@
 	struct rb_node		rb_node;
 	struct list_head	lru;
 	const struct cred *	cred;
+	u64			timestamp;
 	__u32			mask;
 	struct rcu_head		rcu_head;
 };
@@ -81,7 +82,7 @@
 	fl_owner_t flock_owner;
 	struct dentry *dentry;
 	const struct cred *cred;
-	struct rpc_cred *ll_cred;	/* low-level cred - use to check for expiry */
+	struct rpc_cred __rcu *ll_cred;	/* low-level cred - use to check for expiry */
 	struct nfs4_state *state;
 	fmode_t mode;
 
@@ -103,6 +104,7 @@
 	__be32	verf[NFS_DIR_VERIFIER_SIZE];
 	__u64 dir_cookie;
 	__u64 dup_cookie;
+	pgoff_t page_index;
 	signed char duped;
 };
 
@@ -154,35 +156,72 @@
 	unsigned long		attrtimeo_timestamp;
 
 	unsigned long		attr_gencount;
-	/* "Generation counter" for the attribute cache. This is
-	 * bumped whenever we update the metadata on the
-	 * server.
-	 */
-	unsigned long		cache_change_attribute;
 
 	struct rb_root		access_cache;
 	struct list_head	access_cache_entry_lru;
 	struct list_head	access_cache_inode_lru;
 
-	/*
-	 * This is the cookie verifier used for NFSv3 readdir
-	 * operations
-	 */
-	__be32			cookieverf[NFS_DIR_VERIFIER_SIZE];
-
-	atomic_long_t		nrequests;
-	struct nfs_mds_commit_info commit_info;
+	union {
+		/* Directory */
+		struct {
+			/* "Generation counter" for the attribute cache.
+			 * This is bumped whenever we update the metadata
+			 * on the server.
+			 */
+			unsigned long	cache_change_attribute;
+			/*
+			 * This is the cookie verifier used for NFSv3 readdir
+			 * operations
+			 */
+			__be32		cookieverf[NFS_DIR_VERIFIER_SIZE];
+			/* Readers: in-flight sillydelete RPC calls */
+			/* Writers: rmdir */
+			struct rw_semaphore	rmdir_sem;
+		};
+		/* Regular file */
+		struct {
+			atomic_long_t	nrequests;
+			atomic_long_t	redirtied_pages;
+			struct nfs_mds_commit_info commit_info;
+			struct mutex	commit_mutex;
+		};
+	};
 
 	/* Open contexts for shared mmap writes */
 	struct list_head	open_files;
 
-	/* Readers: in-flight sillydelete RPC calls */
-	/* Writers: rmdir */
-	struct rw_semaphore	rmdir_sem;
-	struct mutex		commit_mutex;
-
-	/* track last access to cached pages */
-	unsigned long		page_index;
+	/* Keep track of out-of-order replies.
+	 * The ooo array contains start/end pairs of
+	 * numbers from the changeid sequence when
+	 * the inode's iversion has been updated.
+	 * It also contains end/start pair (i.e. reverse order)
+	 * of sections of the changeid sequence that have
+	 * been seen in replies from the server.
+	 * Normally these should match and when both
+	 * A:B and B:A are found in ooo, they are both removed.
+	 * And if a reply with A:B causes an iversion update
+	 * of A:B, then neither are added.
+	 * When a reply has pre_change that doesn't match
+	 * iversion, then the changeid pair and any consequent
+	 * change in iversion ARE added.  Later replies
+	 * might fill in the gaps, or possibly a gap is caused
+	 * by a change from another client.
+	 * When a file or directory is opened, if the ooo table
+	 * is not empty, then we assume the gaps were due to
+	 * another client and we invalidate the cached data.
+	 *
+	 * We can only track a limited number of concurrent gaps.
+	 * Currently that limit is 16.
+	 * We allocate the table on demand.  If there is insufficient
+	 * memory, then we probably cannot cache the file anyway
+	 * so there is no loss.
+	 */
+	struct {
+		int cnt;
+		struct {
+			u64 start, end;
+		} gap[16];
+	} *ooo;
 
 #if IS_ENABLED(CONFIG_NFS_V4)
 	struct nfs4_cached_acl	*nfs4_acl;
@@ -272,6 +311,7 @@
 #define NFS_INO_INVALIDATING	(3)		/* inode is being invalidated */
 #define NFS_INO_FSCACHE		(5)		/* inode can be cached by FS-Cache */
 #define NFS_INO_FSCACHE_LOCK	(6)		/* FS-Cache cookie management lock */
+#define NFS_INO_FORCE_READDIR	(7)		/* force readdirplus */
 #define NFS_INO_LAYOUTCOMMIT	(9)		/* layoutcommit required */
 #define NFS_INO_LAYOUTCOMMITTING (10)		/* layoutcommit inflight */
 #define NFS_INO_LAYOUTSTATS	(11)		/* layoutstats inflight */
@@ -421,9 +461,22 @@
 extern unsigned long nfs_inc_attr_generation_counter(void);
 
 extern struct nfs_fattr *nfs_alloc_fattr(void);
+extern struct nfs_fattr *nfs_alloc_fattr_with_label(struct nfs_server *server);
+
+static inline void nfs4_label_free(struct nfs4_label *label)
+{
+#ifdef CONFIG_NFS_V4_SECURITY_LABEL
+	if (label) {
+		kfree(label->label);
+		kfree(label);
+	}
+#endif
+}
 
 static inline void nfs_free_fattr(const struct nfs_fattr *fattr)
 {
+	if (fattr)
+		nfs4_label_free(fattr->label);
 	kfree(fattr);
 }
 
@@ -494,10 +547,10 @@
  * linux/fs/nfs/direct.c
  */
 extern ssize_t nfs_direct_IO(struct kiocb *, struct iov_iter *);
-extern ssize_t nfs_file_direct_read(struct kiocb *iocb,
-			struct iov_iter *iter);
-extern ssize_t nfs_file_direct_write(struct kiocb *iocb,
-			struct iov_iter *iter);
+ssize_t nfs_file_direct_read(struct kiocb *iocb,
+			     struct iov_iter *iter, bool swap);
+ssize_t nfs_file_direct_write(struct kiocb *iocb,
+			      struct iov_iter *iter, bool swap);
 
 /*
  * linux/fs/nfs/dir.c
@@ -517,8 +570,8 @@
 			struct nfs_fattr *fattr, struct nfs4_label *label);
 extern int nfs_may_open(struct inode *inode, const struct cred *cred, int openflags);
 extern void nfs_access_zap_cache(struct inode *inode);
-extern int nfs_access_get_cached(struct inode *inode, const struct cred *cred, struct nfs_access_entry *res,
-				 bool may_block);
+extern int nfs_access_get_cached(struct inode *inode, const struct cred *cred,
+				 u32 *mask, bool may_block);
 
 /*
  * linux/fs/nfs/symlink.c
@@ -567,13 +620,17 @@
 extern int nfs_wb_page(struct inode *inode, struct page *page);
 extern int nfs_wb_page_cancel(struct inode *inode, struct page* page);
 extern int  nfs_commit_inode(struct inode *, int);
-extern struct nfs_commit_data *nfs_commitdata_alloc(bool never_fail);
+extern struct nfs_commit_data *nfs_commitdata_alloc(void);
 extern void nfs_commit_free(struct nfs_commit_data *data);
+void nfs_commit_begin(struct nfs_mds_commit_info *cinfo);
+bool nfs_commit_end(struct nfs_mds_commit_info *cinfo);
 
 static inline int
 nfs_have_writebacks(struct inode *inode)
 {
-	return atomic_long_read(&NFS_I(inode)->nrequests) != 0;
+	if (S_ISREG(inode->i_mode))
+		return atomic_long_read(&NFS_I(inode)->nrequests) != 0;
+	return 0;
 }
 
 /*
@@ -601,6 +658,20 @@
 	return ino;
 }
 
+static inline void nfs_ooo_clear(struct nfs_inode *nfsi)
+{
+	nfsi->cache_validity &= ~NFS_INO_DATA_INVAL_DEFER;
+	kfree(nfsi->ooo);
+	nfsi->ooo = NULL;
+}
+
+static inline bool nfs_ooo_test(struct nfs_inode *nfsi)
+{
+	return (nfsi->cache_validity & NFS_INO_DATA_INVAL_DEFER) ||
+		(nfsi->ooo && nfsi->ooo->cnt > 0);
+
+}
+
 #define NFS_JUKEBOX_RETRY_TIME (5 * HZ)
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs_fs_sb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs_fs_sb.h
@@ -48,6 +48,7 @@
 #define NFS_CS_NOPING		6		/* - don't ping on connect */
 #define NFS_CS_DS		7		/* - Server is a DS */
 #define NFS_CS_REUSEPORT	8		/* - reuse src port on reconnect */
+#define NFS_CS_PNFS		9		/* - Server used for pnfs */
 	struct sockaddr_storage	cl_addr;	/* server identifier */
 	size_t			cl_addrlen;
 	char *			cl_hostname;	/* hostname of server */
@@ -237,6 +238,7 @@
 	struct list_head	layouts;
 	struct list_head	delegations;
 	struct list_head	ss_copies;
+	struct list_head	ss_src_copies;
 
 	unsigned long		mig_gen;
 	unsigned long		mig_status;
@@ -287,5 +289,6 @@
 #define NFS_CAP_COPY_NOTIFY	(1U << 27)
 #define NFS_CAP_XATTR		(1U << 28)
 #define NFS_CAP_READ_PLUS	(1U << 29)
-
+#define NFS_CAP_FS_LOCATIONS	(1U << 30)
+#define NFS_CAP_MOVEABLE	(1U << 31)
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs_page.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs_page.h
@@ -145,7 +145,9 @@
 extern	void nfs_unlock_and_release_request(struct nfs_page *);
 extern	struct nfs_page *nfs_page_group_lock_head(struct nfs_page *req);
 extern	int nfs_page_group_lock_subrequests(struct nfs_page *head);
-extern	void nfs_join_page_group(struct nfs_page *head, struct inode *inode);
+extern void nfs_join_page_group(struct nfs_page *head,
+				struct nfs_commit_info *cinfo,
+				struct inode *inode);
 extern int nfs_page_group_lock(struct nfs_page *);
 extern void nfs_page_group_unlock(struct nfs_page *);
 extern bool nfs_page_group_sync_on_bit(struct nfs_page *, unsigned int);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs_ssc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs_ssc.h
@@ -53,6 +53,7 @@
 	if (nfs_ssc_client_tbl.ssc_nfs4_ops)
 		(*nfs_ssc_client_tbl.ssc_nfs4_ops->sco_close)(filep);
 }
+#endif
 
 struct nfsd4_ssc_umount_item {
 	struct list_head nsui_list;
@@ -64,9 +65,8 @@
 	refcount_t nsui_refcnt;
 	unsigned long nsui_expire;
 	struct vfsmount *nsui_vfsmount;
-	char nsui_ipaddr[RPC_MAX_ADDRBUFLEN];
+	char nsui_ipaddr[RPC_MAX_ADDRBUFLEN + 1];
 };
-#endif
 
 /*
  * NFS_FS
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nfs_xdr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nfs_xdr.h
@@ -1219,7 +1219,7 @@
 
 #define NFS4_FS_LOCATIONS_MAXENTRIES 10
 struct nfs4_fs_locations {
-	struct nfs_fattr fattr;
+	struct nfs_fattr *fattr;
 	const struct nfs_server *server;
 	struct nfs4_pathname fs_path;
 	int nlocations;
@@ -1805,6 +1805,9 @@
 	struct nfs_server *(*create_server)(struct fs_context *);
 	struct nfs_server *(*clone_server)(struct nfs_server *, struct nfs_fh *,
 					   struct nfs_fattr *, rpc_authflavor_t);
+	int	(*discover_trunking)(struct nfs_server *, struct nfs_fh *);
+	void	(*enable_swap)(struct inode *inode);
+	void	(*disable_swap)(struct inode *inode);
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nls.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nls.h
@@ -47,7 +47,7 @@
 /* nls_base.c */
 extern int __register_nls(struct nls_table *, struct module *);
 extern int unregister_nls(struct nls_table *);
-extern struct nls_table *load_nls(char *);
+extern struct nls_table *load_nls(const char *charset);
 extern void unload_nls(struct nls_table *);
 extern struct nls_table *load_nls_default(void);
 #define register_nls(nls) __register_nls((nls), THIS_MODULE)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nmi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nmi.h
@@ -122,6 +122,8 @@
 int watchdog_nmi_enable(unsigned int cpu);
 void watchdog_nmi_disable(unsigned int cpu);
 
+void lockup_detector_reconfigure(void);
+
 /**
  * touch_nmi_watchdog - restart NMI watchdog timeout.
  *
@@ -195,7 +197,7 @@
 #endif
 
 #if defined(CONFIG_HARDLOCKUP_CHECK_TIMESTAMP) && \
-    defined(CONFIG_HARDLOCKUP_DETECTOR)
+    defined(CONFIG_HARDLOCKUP_DETECTOR_PERF)
 void watchdog_update_hrtimer_threshold(u64 period);
 #else
 static inline void watchdog_update_hrtimer_threshold(u64 period) { }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nodemask.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nodemask.h
@@ -42,11 +42,11 @@
  * void nodes_shift_right(dst, src, n)	Shift right
  * void nodes_shift_left(dst, src, n)	Shift left
  *
- * int first_node(mask)			Number lowest set bit, or MAX_NUMNODES
- * int next_node(node, mask)		Next node past 'node', or MAX_NUMNODES
- * int next_node_in(node, mask)		Next node past 'node', or wrap to first,
+ * unsigned int first_node(mask)	Number lowest set bit, or MAX_NUMNODES
+ * unsigend int next_node(node, mask)	Next node past 'node', or MAX_NUMNODES
+ * unsigned int next_node_in(node, mask) Next node past 'node', or wrap to first,
  *					or MAX_NUMNODES
- * int first_unset_node(mask)		First node not set in mask, or 
+ * unsigned int first_unset_node(mask)	First node not set in mask, or
  *					MAX_NUMNODES
  *
  * nodemask_t nodemask_of_node(node)	Return nodemask with bit 'node' set
@@ -153,7 +153,7 @@
 
 #define node_test_and_set(node, nodemask) \
 			__node_test_and_set((node), &(nodemask))
-static inline int __node_test_and_set(int node, nodemask_t *addr)
+static inline bool __node_test_and_set(int node, nodemask_t *addr)
 {
 	return test_and_set_bit(node, addr->bits);
 }
@@ -200,7 +200,7 @@
 
 #define nodes_equal(src1, src2) \
 			__nodes_equal(&(src1), &(src2), MAX_NUMNODES)
-static inline int __nodes_equal(const nodemask_t *src1p,
+static inline bool __nodes_equal(const nodemask_t *src1p,
 					const nodemask_t *src2p, unsigned int nbits)
 {
 	return bitmap_equal(src1p->bits, src2p->bits, nbits);
@@ -208,7 +208,7 @@
 
 #define nodes_intersects(src1, src2) \
 			__nodes_intersects(&(src1), &(src2), MAX_NUMNODES)
-static inline int __nodes_intersects(const nodemask_t *src1p,
+static inline bool __nodes_intersects(const nodemask_t *src1p,
 					const nodemask_t *src2p, unsigned int nbits)
 {
 	return bitmap_intersects(src1p->bits, src2p->bits, nbits);
@@ -216,20 +216,20 @@
 
 #define nodes_subset(src1, src2) \
 			__nodes_subset(&(src1), &(src2), MAX_NUMNODES)
-static inline int __nodes_subset(const nodemask_t *src1p,
+static inline bool __nodes_subset(const nodemask_t *src1p,
 					const nodemask_t *src2p, unsigned int nbits)
 {
 	return bitmap_subset(src1p->bits, src2p->bits, nbits);
 }
 
 #define nodes_empty(src) __nodes_empty(&(src), MAX_NUMNODES)
-static inline int __nodes_empty(const nodemask_t *srcp, unsigned int nbits)
+static inline bool __nodes_empty(const nodemask_t *srcp, unsigned int nbits)
 {
 	return bitmap_empty(srcp->bits, nbits);
 }
 
 #define nodes_full(nodemask) __nodes_full(&(nodemask), MAX_NUMNODES)
-static inline int __nodes_full(const nodemask_t *srcp, unsigned int nbits)
+static inline bool __nodes_full(const nodemask_t *srcp, unsigned int nbits)
 {
 	return bitmap_full(srcp->bits, nbits);
 }
@@ -260,15 +260,15 @@
           > MAX_NUMNODES, then the silly min_ts could be dropped. */
 
 #define first_node(src) __first_node(&(src))
-static inline int __first_node(const nodemask_t *srcp)
+static inline unsigned int __first_node(const nodemask_t *srcp)
 {
-	return min_t(int, MAX_NUMNODES, find_first_bit(srcp->bits, MAX_NUMNODES));
+	return min_t(unsigned int, MAX_NUMNODES, find_first_bit(srcp->bits, MAX_NUMNODES));
 }
 
 #define next_node(n, src) __next_node((n), &(src))
-static inline int __next_node(int n, const nodemask_t *srcp)
+static inline unsigned int __next_node(int n, const nodemask_t *srcp)
 {
-	return min_t(int,MAX_NUMNODES,find_next_bit(srcp->bits, MAX_NUMNODES, n+1));
+	return min_t(unsigned int, MAX_NUMNODES, find_next_bit(srcp->bits, MAX_NUMNODES, n+1));
 }
 
 /*
@@ -276,7 +276,7 @@
  * the first node in src if needed.  Returns MAX_NUMNODES if src is empty.
  */
 #define next_node_in(n, src) __next_node_in((n), &(src))
-int __next_node_in(int node, const nodemask_t *srcp);
+unsigned int __next_node_in(int node, const nodemask_t *srcp);
 
 static inline void init_nodemask_of_node(nodemask_t *mask, int node)
 {
@@ -296,9 +296,9 @@
 })
 
 #define first_unset_node(mask) __first_unset_node(&(mask))
-static inline int __first_unset_node(const nodemask_t *maskp)
+static inline unsigned int __first_unset_node(const nodemask_t *maskp)
 {
-	return min_t(int,MAX_NUMNODES,
+	return min_t(unsigned int, MAX_NUMNODES,
 			find_first_zero_bit(maskp->bits, MAX_NUMNODES));
 }
 
@@ -375,14 +375,13 @@
 }
 
 #if MAX_NUMNODES > 1
-#define for_each_node_mask(node, mask)			\
-	for ((node) = first_node(mask);			\
-		(node) < MAX_NUMNODES;			\
-		(node) = next_node((node), (mask)))
+#define for_each_node_mask(node, mask)				    \
+	for ((node) = first_node(mask);				    \
+	     (node >= 0) && (node) < MAX_NUMNODES;		    \
+	     (node) = next_node((node), (mask)))
 #else /* MAX_NUMNODES == 1 */
-#define for_each_node_mask(node, mask)			\
-	if (!nodes_empty(mask))				\
-		for ((node) = 0; (node) < 1; (node)++)
+#define for_each_node_mask(node, mask)                                  \
+	for ((node) = 0; (node) < 1 && !nodes_empty(mask); (node)++)
 #endif /* MAX_NUMNODES */
 
 /*
@@ -436,11 +435,11 @@
 
 #define first_online_node	first_node(node_states[N_ONLINE])
 #define first_memory_node	first_node(node_states[N_MEMORY])
-static inline int next_online_node(int nid)
+static inline unsigned int next_online_node(int nid)
 {
 	return next_node(nid, node_states[N_ONLINE]);
 }
-static inline int next_memory_node(int nid)
+static inline unsigned int next_memory_node(int nid)
 {
 	return next_node(nid, node_states[N_MEMORY]);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nospec.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nospec.h
@@ -11,6 +11,10 @@
 
 struct task_struct;
 
+#ifndef barrier_nospec
+# define barrier_nospec() do { } while (0)
+#endif
+
 /**
  * array_index_mask_nospec() - generate a ~0 mask when index < size, 0 otherwise
  * @index: array element index
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nvme-tcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nvme-tcp.h
@@ -114,8 +114,9 @@
 struct nvme_tcp_term_pdu {
 	struct nvme_tcp_hdr	hdr;
 	__le16			fes;
-	__le32			fei;
-	__u8			rsvd[8];
+	__le16			feil;
+	__le16			feiu;
+	__u8			rsvd[10];
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nvme.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nvme.h
@@ -7,6 +7,7 @@
 #ifndef _LINUX_NVME_H
 #define _LINUX_NVME_H
 
+#include <linux/bits.h>
 #include <linux/types.h>
 #include <linux/uuid.h>
 
@@ -31,6 +32,18 @@
 	NVME_NQN_NVME	= 2,		/* NVME type target subsystem */
 };
 
+enum nvme_ctrl_type {
+	NVME_CTRL_IO	= 1,		/* I/O controller */
+	NVME_CTRL_DISC	= 2,		/* Discovery controller */
+	NVME_CTRL_ADMIN	= 3,		/* Administrative controller */
+};
+
+enum nvme_dctype {
+	NVME_DCTYPE_NOT_REPORTED	= 0,
+	NVME_DCTYPE_DDC			= 1, /* Direct Discovery Controller */
+	NVME_DCTYPE_CDC			= 2, /* Central Discovery Controller */
+};
+
 /* Address Family codes for Discovery Log Page entry ADRFAM field */
 enum {
 	NVMF_ADDR_FAMILY_PCI	= 0,	/* PCIe */
@@ -70,8 +83,8 @@
 	NVMF_RDMA_QPTYPE_DATAGRAM	= 2, /* Reliable Datagram */
 };
 
-/* RDMA QP Service Type codes for Discovery Log Page entry TSAS
- * RDMA_QPTYPE field
+/* RDMA Provider Type codes for Discovery Log Page entry TSAS
+ * RDMA_PRTYPE field
  */
 enum {
 	NVMF_RDMA_PRTYPE_NOT_SPECIFIED	= 1, /* No Provider Specified */
@@ -244,7 +257,9 @@
 	__le32			rtd3e;
 	__le32			oaes;
 	__le32			ctratt;
-	__u8			rsvd100[28];
+	__u8			rsvd100[11];
+	__u8			cntrltype;
+	__u8			fguid[16];
 	__le16			crdt1;
 	__le16			crdt2;
 	__le16			crdt3;
@@ -306,7 +321,9 @@
 	__le16			icdoff;
 	__u8			ctrattr;
 	__u8			msdbd;
-	__u8			rsvd1804[244];
+	__u8			rsvd1804[2];
+	__u8			dctype;
+	__u8			rsvd1807[241];
 	struct nvme_id_power_state	psd[32];
 	__u8			vs[1024];
 };
@@ -322,6 +339,7 @@
 	NVME_CTRL_ONCS_TIMESTAMP		= 1 << 6,
 	NVME_CTRL_VWC_PRESENT			= 1 << 0,
 	NVME_CTRL_OACS_SEC_SUPP                 = 1 << 0,
+	NVME_CTRL_OACS_NS_MNGT_SUPP		= 1 << 3,
 	NVME_CTRL_OACS_DIRECTIVES		= 1 << 5,
 	NVME_CTRL_OACS_DBBUF_SUPP		= 1 << 8,
 	NVME_CTRL_LPA_CMD_EFFECTS_LOG		= 1 << 1,
@@ -538,7 +556,7 @@
 	NVME_CMD_EFFECTS_NCC		= 1 << 2,
 	NVME_CMD_EFFECTS_NIC		= 1 << 3,
 	NVME_CMD_EFFECTS_CCC		= 1 << 4,
-	NVME_CMD_EFFECTS_CSE_MASK	= 3 << 16,
+	NVME_CMD_EFFECTS_CSE_MASK	= GENMASK(18, 16),
 	NVME_CMD_EFFECTS_UUID_SEL	= 1 << 19,
 };
 
@@ -612,6 +630,10 @@
 };
 
 enum {
+	NVME_AER_ERROR_PERSIST_INT_ERR	= 0x03,
+};
+
+enum {
 	NVME_AER_NOTICE_NS_CHANGED	= 0x00,
 	NVME_AER_NOTICE_FW_ACT_STARTING = 0x01,
 	NVME_AER_NOTICE_ANA		= 0x03,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/nvmem-provider.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/nvmem-provider.h
@@ -66,7 +66,7 @@
  * @word_size:	Minimum read/write access granularity.
  * @stride:	Minimum read/write access stride.
  * @priv:	User context passed to read/write callbacks.
- * @wp-gpio:   Write protect pin
+ * @ignore_wp:  Write Protect pin is managed by the provider.
  *
  * Note: A default "nvmem<id>" name will be assigned to the device if
  * no name is specified in its configuration. In such case "<id>" is
@@ -80,7 +80,6 @@
 	const char		*name;
 	int			id;
 	struct module		*owner;
-	struct gpio_desc	*wp_gpio;
 	const struct nvmem_cell_info	*cells;
 	int			ncells;
 	const struct nvmem_keepout *keepout;
@@ -88,6 +87,7 @@
 	enum nvmem_type		type;
 	bool			read_only;
 	bool			root_only;
+	bool			ignore_wp;
 	struct device_node	*of_node;
 	bool			no_of_node;
 	nvmem_reg_read_t	reg_read;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/objagg.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/objagg.h
@@ -8,7 +8,6 @@
 	size_t obj_size;
 	bool (*delta_check)(void *priv, const void *parent_obj,
 			    const void *obj);
-	int (*hints_obj_cmp)(const void *obj1, const void *obj2);
 	void * (*delta_create)(void *priv, void *parent_obj, void *obj);
 	void (*delta_destroy)(void *priv, void *delta_priv);
 	void * (*root_create)(void *priv, void *obj, unsigned int root_id);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/objtool.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/objtool.h
@@ -32,11 +32,16 @@
  *
  * UNWIND_HINT_FUNC: Generate the unwind metadata of a callable function.
  * Useful for code which doesn't have an ELF function annotation.
+ *
+ * UNWIND_HINT_ENTRY: machine entry without stack, SYSCALL/SYSENTER etc.
  */
 #define UNWIND_HINT_TYPE_CALL		0
 #define UNWIND_HINT_TYPE_REGS		1
 #define UNWIND_HINT_TYPE_REGS_PARTIAL	2
 #define UNWIND_HINT_TYPE_FUNC		3
+#define UNWIND_HINT_TYPE_ENTRY		4
+#define UNWIND_HINT_TYPE_SAVE		5
+#define UNWIND_HINT_TYPE_RESTORE	6
 
 #ifdef CONFIG_STACK_VALIDATION
 
@@ -66,6 +71,23 @@
 	static void __used __section(".discard.func_stack_frame_non_standard") \
 		*__func_stack_frame_non_standard_##func = func
 
+/*
+ * STACK_FRAME_NON_STANDARD_FP() is a frame-pointer-specific function ignore
+ * for the case where a function is intentionally missing frame pointer setup,
+ * but otherwise needs objtool/ORC coverage when frame pointers are disabled.
+ */
+#ifdef CONFIG_FRAME_POINTER
+#define STACK_FRAME_NON_STANDARD_FP(func) STACK_FRAME_NON_STANDARD(func)
+#else
+#define STACK_FRAME_NON_STANDARD_FP(func)
+#endif
+
+#define ANNOTATE_NOENDBR					\
+	"986: \n\t"						\
+	".pushsection .discard.noendbr\n\t"			\
+	_ASM_PTR " 986b\n\t"					\
+	".popsection\n\t"
+
 #else /* __ASSEMBLY__ */
 
 /*
@@ -99,7 +121,7 @@
  * the debuginfo as necessary.  It will also warn if it sees any
  * inconsistencies.
  */
-.macro UNWIND_HINT sp_reg:req sp_offset=0 type:req end=0
+.macro UNWIND_HINT type:req sp_reg=0 sp_offset=0 end=0
 .Lunwind_hint_ip_\@:
 	.pushsection .discard.unwind_hints
 		/* struct unwind_hint */
@@ -118,6 +140,13 @@
 	.popsection
 .endm
 
+.macro ANNOTATE_NOENDBR
+.Lhere_\@:
+	.pushsection .discard.noendbr
+	.quad	.Lhere_\@
+	.popsection
+.endm
+
 #endif /* __ASSEMBLY__ */
 
 #else /* !CONFIG_STACK_VALIDATION */
@@ -127,12 +156,16 @@
 #define UNWIND_HINT(sp_reg, sp_offset, type, end)	\
 	"\n\t"
 #define STACK_FRAME_NON_STANDARD(func)
+#define STACK_FRAME_NON_STANDARD_FP(func)
+#define ANNOTATE_NOENDBR
 #else
 #define ANNOTATE_INTRA_FUNCTION_CALL
-.macro UNWIND_HINT sp_reg:req sp_offset=0 type:req end=0
+.macro UNWIND_HINT type:req sp_reg=0 sp_offset=0 end=0
 .endm
 .macro STACK_FRAME_NON_STANDARD func:req
 .endm
+.macro ANNOTATE_NOENDBR
+.endm
 #endif
 
 #endif /* CONFIG_STACK_VALIDATION */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/of.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/of.h
@@ -415,130 +415,6 @@
 
 #define of_match_ptr(_ptr)	(_ptr)
 
-/**
- * of_property_read_u8_array - Find and read an array of u8 from a property.
- *
- * @np:		device node from which the property value is to be read.
- * @propname:	name of the property to be searched.
- * @out_values:	pointer to return value, modified only if return value is 0.
- * @sz:		number of array elements to read
- *
- * Search for a property in a device node and read 8-bit value(s) from
- * it.
- *
- * dts entry of array should be like:
- *  ``property = /bits/ 8 <0x50 0x60 0x70>;``
- *
- * Return: 0 on success, -EINVAL if the property does not exist,
- * -ENODATA if property does not have a value, and -EOVERFLOW if the
- * property data isn't large enough.
- *
- * The out_values is modified only if a valid u8 value can be decoded.
- */
-static inline int of_property_read_u8_array(const struct device_node *np,
-					    const char *propname,
-					    u8 *out_values, size_t sz)
-{
-	int ret = of_property_read_variable_u8_array(np, propname, out_values,
-						     sz, 0);
-	if (ret >= 0)
-		return 0;
-	else
-		return ret;
-}
-
-/**
- * of_property_read_u16_array - Find and read an array of u16 from a property.
- *
- * @np:		device node from which the property value is to be read.
- * @propname:	name of the property to be searched.
- * @out_values:	pointer to return value, modified only if return value is 0.
- * @sz:		number of array elements to read
- *
- * Search for a property in a device node and read 16-bit value(s) from
- * it.
- *
- * dts entry of array should be like:
- *  ``property = /bits/ 16 <0x5000 0x6000 0x7000>;``
- *
- * Return: 0 on success, -EINVAL if the property does not exist,
- * -ENODATA if property does not have a value, and -EOVERFLOW if the
- * property data isn't large enough.
- *
- * The out_values is modified only if a valid u16 value can be decoded.
- */
-static inline int of_property_read_u16_array(const struct device_node *np,
-					     const char *propname,
-					     u16 *out_values, size_t sz)
-{
-	int ret = of_property_read_variable_u16_array(np, propname, out_values,
-						      sz, 0);
-	if (ret >= 0)
-		return 0;
-	else
-		return ret;
-}
-
-/**
- * of_property_read_u32_array - Find and read an array of 32 bit integers
- * from a property.
- *
- * @np:		device node from which the property value is to be read.
- * @propname:	name of the property to be searched.
- * @out_values:	pointer to return value, modified only if return value is 0.
- * @sz:		number of array elements to read
- *
- * Search for a property in a device node and read 32-bit value(s) from
- * it.
- *
- * Return: 0 on success, -EINVAL if the property does not exist,
- * -ENODATA if property does not have a value, and -EOVERFLOW if the
- * property data isn't large enough.
- *
- * The out_values is modified only if a valid u32 value can be decoded.
- */
-static inline int of_property_read_u32_array(const struct device_node *np,
-					     const char *propname,
-					     u32 *out_values, size_t sz)
-{
-	int ret = of_property_read_variable_u32_array(np, propname, out_values,
-						      sz, 0);
-	if (ret >= 0)
-		return 0;
-	else
-		return ret;
-}
-
-/**
- * of_property_read_u64_array - Find and read an array of 64 bit integers
- * from a property.
- *
- * @np:		device node from which the property value is to be read.
- * @propname:	name of the property to be searched.
- * @out_values:	pointer to return value, modified only if return value is 0.
- * @sz:		number of array elements to read
- *
- * Search for a property in a device node and read 64-bit value(s) from
- * it.
- *
- * Return: 0 on success, -EINVAL if the property does not exist,
- * -ENODATA if property does not have a value, and -EOVERFLOW if the
- * property data isn't large enough.
- *
- * The out_values is modified only if a valid u64 value can be decoded.
- */
-static inline int of_property_read_u64_array(const struct device_node *np,
-					     const char *propname,
-					     u64 *out_values, size_t sz)
-{
-	int ret = of_property_read_variable_u64_array(np, propname, out_values,
-						      sz, 0);
-	if (ret >= 0)
-		return 0;
-	else
-		return ret;
-}
-
 /*
  * struct property *prop;
  * const __be32 *p;
@@ -574,7 +450,7 @@
 				   unsigned long initrd_len,
 				   const char *cmdline, size_t extra_fdt_size);
 int ima_get_kexec_buffer(void **addr, size_t *size);
-int ima_free_kexec_buffer(void);
+int __init ima_free_kexec_buffer(void);
 #else /* CONFIG_OF */
 
 static inline void of_core_init(void)
@@ -733,32 +609,6 @@
 	return -ENOSYS;
 }
 
-static inline int of_property_read_u8_array(const struct device_node *np,
-			const char *propname, u8 *out_values, size_t sz)
-{
-	return -ENOSYS;
-}
-
-static inline int of_property_read_u16_array(const struct device_node *np,
-			const char *propname, u16 *out_values, size_t sz)
-{
-	return -ENOSYS;
-}
-
-static inline int of_property_read_u32_array(const struct device_node *np,
-					     const char *propname,
-					     u32 *out_values, size_t sz)
-{
-	return -ENOSYS;
-}
-
-static inline int of_property_read_u64_array(const struct device_node *np,
-					     const char *propname,
-					     u64 *out_values, size_t sz)
-{
-	return -ENOSYS;
-}
-
 static inline int of_property_read_u32_index(const struct device_node *np,
 			const char *propname, u32 index, u32 *out_value)
 {
@@ -1223,7 +1073,8 @@
  * @np:		device node from which the property value is to be read.
  * @propname:	name of the property to be searched.
  *
- * Search for a property in a device node.
+ * Search for a boolean property in a device node. Usage on non-boolean
+ * property types is deprecated.
  *
  * Return: true if the property exists false otherwise.
  */
@@ -1235,6 +1086,144 @@
 	return prop ? true : false;
 }
 
+/**
+ * of_property_present - Test if a property is present in a node
+ * @np:		device node to search for the property.
+ * @propname:	name of the property to be searched.
+ *
+ * Test for a property present in a device node.
+ *
+ * Return: true if the property exists false otherwise.
+ */
+static inline bool of_property_present(const struct device_node *np, const char *propname)
+{
+	return of_property_read_bool(np, propname);
+}
+
+/**
+ * of_property_read_u8_array - Find and read an array of u8 from a property.
+ *
+ * @np:		device node from which the property value is to be read.
+ * @propname:	name of the property to be searched.
+ * @out_values:	pointer to return value, modified only if return value is 0.
+ * @sz:		number of array elements to read
+ *
+ * Search for a property in a device node and read 8-bit value(s) from
+ * it.
+ *
+ * dts entry of array should be like:
+ *  ``property = /bits/ 8 <0x50 0x60 0x70>;``
+ *
+ * Return: 0 on success, -EINVAL if the property does not exist,
+ * -ENODATA if property does not have a value, and -EOVERFLOW if the
+ * property data isn't large enough.
+ *
+ * The out_values is modified only if a valid u8 value can be decoded.
+ */
+static inline int of_property_read_u8_array(const struct device_node *np,
+					    const char *propname,
+					    u8 *out_values, size_t sz)
+{
+	int ret = of_property_read_variable_u8_array(np, propname, out_values,
+						     sz, 0);
+	if (ret >= 0)
+		return 0;
+	else
+		return ret;
+}
+
+/**
+ * of_property_read_u16_array - Find and read an array of u16 from a property.
+ *
+ * @np:		device node from which the property value is to be read.
+ * @propname:	name of the property to be searched.
+ * @out_values:	pointer to return value, modified only if return value is 0.
+ * @sz:		number of array elements to read
+ *
+ * Search for a property in a device node and read 16-bit value(s) from
+ * it.
+ *
+ * dts entry of array should be like:
+ *  ``property = /bits/ 16 <0x5000 0x6000 0x7000>;``
+ *
+ * Return: 0 on success, -EINVAL if the property does not exist,
+ * -ENODATA if property does not have a value, and -EOVERFLOW if the
+ * property data isn't large enough.
+ *
+ * The out_values is modified only if a valid u16 value can be decoded.
+ */
+static inline int of_property_read_u16_array(const struct device_node *np,
+					     const char *propname,
+					     u16 *out_values, size_t sz)
+{
+	int ret = of_property_read_variable_u16_array(np, propname, out_values,
+						      sz, 0);
+	if (ret >= 0)
+		return 0;
+	else
+		return ret;
+}
+
+/**
+ * of_property_read_u32_array - Find and read an array of 32 bit integers
+ * from a property.
+ *
+ * @np:		device node from which the property value is to be read.
+ * @propname:	name of the property to be searched.
+ * @out_values:	pointer to return value, modified only if return value is 0.
+ * @sz:		number of array elements to read
+ *
+ * Search for a property in a device node and read 32-bit value(s) from
+ * it.
+ *
+ * Return: 0 on success, -EINVAL if the property does not exist,
+ * -ENODATA if property does not have a value, and -EOVERFLOW if the
+ * property data isn't large enough.
+ *
+ * The out_values is modified only if a valid u32 value can be decoded.
+ */
+static inline int of_property_read_u32_array(const struct device_node *np,
+					     const char *propname,
+					     u32 *out_values, size_t sz)
+{
+	int ret = of_property_read_variable_u32_array(np, propname, out_values,
+						      sz, 0);
+	if (ret >= 0)
+		return 0;
+	else
+		return ret;
+}
+
+/**
+ * of_property_read_u64_array - Find and read an array of 64 bit integers
+ * from a property.
+ *
+ * @np:		device node from which the property value is to be read.
+ * @propname:	name of the property to be searched.
+ * @out_values:	pointer to return value, modified only if return value is 0.
+ * @sz:		number of array elements to read
+ *
+ * Search for a property in a device node and read 64-bit value(s) from
+ * it.
+ *
+ * Return: 0 on success, -EINVAL if the property does not exist,
+ * -ENODATA if property does not have a value, and -EOVERFLOW if the
+ * property data isn't large enough.
+ *
+ * The out_values is modified only if a valid u64 value can be decoded.
+ */
+static inline int of_property_read_u64_array(const struct device_node *np,
+					     const char *propname,
+					     u64 *out_values, size_t sz)
+{
+	int ret = of_property_read_variable_u64_array(np, propname, out_values,
+						      sz, 0);
+	if (ret >= 0)
+		return 0;
+	else
+		return ret;
+}
+
 static inline int of_property_read_u8(const struct device_node *np,
 				       const char *propname,
 				       u8 *out_value)
@@ -1486,12 +1475,26 @@
  */
 
 enum of_overlay_notify_action {
-	OF_OVERLAY_PRE_APPLY = 0,
+	OF_OVERLAY_INIT = 0,	/* kzalloc() of ovcs sets this value */
+	OF_OVERLAY_PRE_APPLY,
 	OF_OVERLAY_POST_APPLY,
 	OF_OVERLAY_PRE_REMOVE,
 	OF_OVERLAY_POST_REMOVE,
 };
 
+static inline char *of_overlay_action_name(enum of_overlay_notify_action action)
+{
+	static char *of_overlay_action_name[] = {
+		"init",
+		"pre-apply",
+		"post-apply",
+		"pre-remove",
+		"post-remove",
+	};
+
+	return of_overlay_action_name[action];
+}
+
 struct of_overlay_notify_data {
 	struct device_node *overlay;
 	struct device_node *target;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/of_device.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/of_device.h
@@ -101,8 +101,9 @@
 }
 
 static inline int of_dma_configure_id(struct device *dev,
-				   struct device_node *np,
-				   bool force_dma)
+				      struct device_node *np,
+				      bool force_dma,
+				      const u32 *id)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/of_fdt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/of_fdt.h
@@ -62,6 +62,7 @@
 				     int depth, void *data);
 extern int early_init_dt_scan_memory(unsigned long node, const char *uname,
 				     int depth, void *data);
+extern void early_init_dt_check_for_usable_mem_range(void);
 extern int early_init_dt_scan_chosen_stdout(void);
 extern void early_init_fdt_scan_reserved_mem(void);
 extern void early_init_fdt_reserve_self(void);
@@ -87,6 +88,7 @@
 extern void early_init_devtree(void *);
 extern void early_get_first_memblock_info(void *, phys_addr_t *);
 #else /* CONFIG_OF_EARLY_FLATTREE */
+static inline void early_init_dt_check_for_usable_mem_range(void) {}
 static inline int early_init_dt_scan_chosen_stdout(void) { return -ENODEV; }
 static inline void early_init_fdt_scan_reserved_mem(void) {}
 static inline void early_init_fdt_reserve_self(void) {}
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/of_irq.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/of_irq.h
@@ -10,7 +10,9 @@
 #include <linux/of.h>
 
 typedef int (*of_irq_init_cb_t)(struct device_node *, struct device_node *);
-
+#ifdef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
+typedef int (*of_irq_remove_cb_t)(struct device_node *, struct device_node *);
+#endif
 /*
  * Workarounds only applied to 32bit powermac machines
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/of_mdio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/of_mdio.h
@@ -14,9 +14,25 @@
 
 #if IS_ENABLED(CONFIG_OF_MDIO)
 bool of_mdiobus_child_is_phy(struct device_node *child);
-int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np);
-int devm_of_mdiobus_register(struct device *dev, struct mii_bus *mdio,
-			     struct device_node *np);
+int __of_mdiobus_register(struct mii_bus *mdio, struct device_node *np,
+			  struct module *owner);
+
+static inline int of_mdiobus_register(struct mii_bus *mdio,
+				      struct device_node *np)
+{
+	return __of_mdiobus_register(mdio, np, THIS_MODULE);
+}
+
+int __devm_of_mdiobus_register(struct device *dev, struct mii_bus *mdio,
+			       struct device_node *np, struct module *owner);
+
+static inline int devm_of_mdiobus_register(struct device *dev,
+					   struct mii_bus *mdio,
+					   struct device_node *np)
+{
+	return __devm_of_mdiobus_register(dev, mdio, np, THIS_MODULE);
+}
+
 struct mdio_device *of_mdio_find_device(struct device_node *np);
 struct phy_device *of_phy_find_device(struct device_node *phy_np);
 struct phy_device *
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/of_net.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/of_net.h
@@ -8,12 +8,13 @@
 
 #include <linux/phy.h>
 
-#ifdef CONFIG_OF_NET
+#if defined(CONFIG_OF) && defined(CONFIG_NET)
 #include <linux/of.h>
 
 struct net_device;
 extern int of_get_phy_mode(struct device_node *np, phy_interface_t *interface);
 extern int of_get_mac_address(struct device_node *np, u8 *mac);
+int of_get_ethdev_address(struct device_node *np, struct net_device *dev);
 extern struct net_device *of_find_net_device_by_node(struct device_node *np);
 #else
 static inline int of_get_phy_mode(struct device_node *np,
@@ -26,6 +27,11 @@
 {
 	return -ENODEV;
 }
+
+static inline int of_get_ethdev_address(struct device_node *np, struct net_device *dev)
+{
+	return -ENODEV;
+}
 
 static inline struct net_device *of_find_net_device_by_node(struct device_node *np)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/once.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/once.h
@@ -5,10 +5,18 @@
 #include <linux/types.h>
 #include <linux/jump_label.h>
 
+/* Helpers used from arbitrary contexts.
+ * Hard irqs are blocked, be cautious.
+ */
 bool __do_once_start(bool *done, unsigned long *flags);
 void __do_once_done(bool *done, struct static_key_true *once_key,
 		    unsigned long *flags, struct module *mod);
 
+/* Variant for process contexts only. */
+bool __do_once_slow_start(bool *done);
+void __do_once_slow_done(bool *done, struct static_key_true *once_key,
+			 struct module *mod);
+
 /* Call a function exactly once. The idea of DO_ONCE() is to perform
  * a function call such as initialization of random seeds, etc, only
  * once, where DO_ONCE() can live in the fast-path. After @func has
@@ -52,9 +60,29 @@
 		___ret;							     \
 	})
 
+/* Variant of DO_ONCE() for process/sleepable contexts. */
+#define DO_ONCE_SLOW(func, ...)						     \
+	({								     \
+		bool ___ret = false;					     \
+		static bool __section(".data.once") ___done = false;	     \
+		static DEFINE_STATIC_KEY_TRUE(___once_key);		     \
+		if (static_branch_unlikely(&___once_key)) {		     \
+			___ret = __do_once_slow_start(&___done);	     \
+			if (unlikely(___ret)) {				     \
+				func(__VA_ARGS__);			     \
+				__do_once_slow_done(&___done, &___once_key,  \
+						    THIS_MODULE);	     \
+			}						     \
+		}							     \
+		___ret;							     \
+	})
+
 #define get_random_once(buf, nbytes)					     \
 	DO_ONCE(get_random_bytes, (buf), (nbytes))
 #define get_random_once_wait(buf, nbytes)                                    \
 	DO_ONCE(get_random_bytes_wait, (buf), (nbytes))                      \
 
+#define get_random_slow_once(buf, nbytes)				     \
+	DO_ONCE_SLOW(get_random_bytes, (buf), (nbytes))
+
 #endif /* _LINUX_ONCE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/once_lite.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/once_lite.h
@@ -9,15 +9,27 @@
  */
 #define DO_ONCE_LITE(func, ...)						\
 	DO_ONCE_LITE_IF(true, func, ##__VA_ARGS__)
-#define DO_ONCE_LITE_IF(condition, func, ...)				\
+
+#define __ONCE_LITE_IF(condition)					\
 	({								\
 		static bool __section(".data.once") __already_done;	\
-		bool __ret_do_once = !!(condition);			\
+		bool __ret_cond = !!(condition);			\
+		bool __ret_once = false;				\
 									\
-		if (unlikely(__ret_do_once && !__already_done)) {	\
+		if (unlikely(__ret_cond && !__already_done)) {		\
 			__already_done = true;				\
-			func(__VA_ARGS__);				\
+			__ret_once = true;				\
 		}							\
+		unlikely(__ret_once);					\
+	})
+
+#define DO_ONCE_LITE_IF(condition, func, ...)				\
+	({								\
+		bool __ret_do_once = !!(condition);			\
+									\
+		if (__ONCE_LITE_IF(__ret_do_once))			\
+			func(__VA_ARGS__);				\
+									\
 		unlikely(__ret_do_once);				\
 	})
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/overflow.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/overflow.h
@@ -29,7 +29,6 @@
  * https://mail-index.netbsd.org/tech-misc/2007/02/05/0000.html -
  * credit to Christian Biere.
  */
-#define is_signed_type(type)       (((type)(-1)) < (type)1)
 #define __type_half_max(type) ((type)1 << (8*sizeof(type) - 1 - is_signed_type(type)))
 #define type_max(T) ((T)((__type_half_max(T) - 1) + __type_half_max(T)))
 #define type_min(T) ((T)((T)-type_max(T)-(T)1))
@@ -51,40 +50,50 @@
 	return unlikely(overflow);
 }
 
-/*
- * For simplicity and code hygiene, the fallback code below insists on
- * a, b and *d having the same type (similar to the min() and max()
- * macros), whereas gcc's type-generic overflow checkers accept
- * different types. Hence we don't just make check_add_overflow an
- * alias for __builtin_add_overflow, but add type checks similar to
- * below.
- */
-#define check_add_overflow(a, b, d) __must_check_overflow(({	\
-	typeof(a) __a = (a);			\
-	typeof(b) __b = (b);			\
-	typeof(d) __d = (d);			\
-	(void) (&__a == &__b);			\
-	(void) (&__a == __d);			\
-	__builtin_add_overflow(__a, __b, __d);	\
-}))
+/** check_add_overflow() - Calculate addition with overflow checking
+ *
+ * @a: first addend
+ * @b: second addend
+ * @d: pointer to store sum
+ *
+ * Returns 0 on success.
+ *
+ * *@d holds the results of the attempted addition, but is not considered
+ * "safe for use" on a non-zero return value, which indicates that the
+ * sum has overflowed or been truncated.
+ */
+#define check_add_overflow(a, b, d)	\
+	__must_check_overflow(__builtin_add_overflow(a, b, d))
 
-#define check_sub_overflow(a, b, d) __must_check_overflow(({	\
-	typeof(a) __a = (a);			\
-	typeof(b) __b = (b);			\
-	typeof(d) __d = (d);			\
-	(void) (&__a == &__b);			\
-	(void) (&__a == __d);			\
-	__builtin_sub_overflow(__a, __b, __d);	\
-}))
+/** check_sub_overflow() - Calculate subtraction with overflow checking
+ *
+ * @a: minuend; value to subtract from
+ * @b: subtrahend; value to subtract from @a
+ * @d: pointer to store difference
+ *
+ * Returns 0 on success.
+ *
+ * *@d holds the results of the attempted subtraction, but is not considered
+ * "safe for use" on a non-zero return value, which indicates that the
+ * difference has underflowed or been truncated.
+ */
+#define check_sub_overflow(a, b, d)	\
+	__must_check_overflow(__builtin_sub_overflow(a, b, d))
 
-#define check_mul_overflow(a, b, d) __must_check_overflow(({	\
-	typeof(a) __a = (a);			\
-	typeof(b) __b = (b);			\
-	typeof(d) __d = (d);			\
-	(void) (&__a == &__b);			\
-	(void) (&__a == __d);			\
-	__builtin_mul_overflow(__a, __b, __d);	\
-}))
+/** check_mul_overflow() - Calculate multiplication with overflow checking
+ *
+ * @a: first factor
+ * @b: second factor
+ * @d: pointer to store product
+ *
+ * Returns 0 on success.
+ *
+ * *@d holds the results of the attempted multiplication, but is not
+ * considered "safe for use" on a non-zero return value, which indicates
+ * that the product has overflowed or been truncated.
+ */
+#define check_mul_overflow(a, b, d)	\
+	__must_check_overflow(__builtin_mul_overflow(a, b, d))
 
 /** check_shl_overflow() - Calculate a left-shifted value and check overflow
  *
@@ -118,81 +127,94 @@
 }))
 
 /**
- * array_size() - Calculate size of 2-dimensional array.
+ * size_mul() - Calculate size_t multiplication with saturation at SIZE_MAX
  *
- * @a: dimension one
- * @b: dimension two
+ * @factor1: first factor
+ * @factor2: second factor
  *
- * Calculates size of 2-dimensional array: @a * @b.
- *
- * Returns: number of bytes needed to represent the array or SIZE_MAX on
- * overflow.
+ * Returns: calculate @factor1 * @factor2, both promoted to size_t,
+ * with any overflow causing the return value to be SIZE_MAX. The
+ * lvalue must be size_t to avoid implicit type conversion.
  */
-static inline __must_check size_t array_size(size_t a, size_t b)
+static inline size_t __must_check size_mul(size_t factor1, size_t factor2)
 {
 	size_t bytes;
 
-	if (check_mul_overflow(a, b, &bytes))
+	if (check_mul_overflow(factor1, factor2, &bytes))
 		return SIZE_MAX;
 
 	return bytes;
 }
 
 /**
- * array3_size() - Calculate size of 3-dimensional array.
- *
- * @a: dimension one
- * @b: dimension two
- * @c: dimension three
+ * size_add() - Calculate size_t addition with saturation at SIZE_MAX
  *
- * Calculates size of 3-dimensional array: @a * @b * @c.
+ * @addend1: first addend
+ * @addend2: second addend
  *
- * Returns: number of bytes needed to represent the array or SIZE_MAX on
- * overflow.
+ * Returns: calculate @addend1 + @addend2, both promoted to size_t,
+ * with any overflow causing the return value to be SIZE_MAX. The
+ * lvalue must be size_t to avoid implicit type conversion.
  */
-static inline __must_check size_t array3_size(size_t a, size_t b, size_t c)
+static inline size_t __must_check size_add(size_t addend1, size_t addend2)
 {
 	size_t bytes;
 
-	if (check_mul_overflow(a, b, &bytes))
-		return SIZE_MAX;
-	if (check_mul_overflow(bytes, c, &bytes))
+	if (check_add_overflow(addend1, addend2, &bytes))
 		return SIZE_MAX;
 
 	return bytes;
 }
 
-/*
- * Compute a*b+c, returning SIZE_MAX on overflow. Internal helper for
- * struct_size() below.
+/**
+ * size_sub() - Calculate size_t subtraction with saturation at SIZE_MAX
+ *
+ * @minuend: value to subtract from
+ * @subtrahend: value to subtract from @minuend
+ *
+ * Returns: calculate @minuend - @subtrahend, both promoted to size_t,
+ * with any overflow causing the return value to be SIZE_MAX. For
+ * composition with the size_add() and size_mul() helpers, neither
+ * argument may be SIZE_MAX (or the result with be forced to SIZE_MAX).
+ * The lvalue must be size_t to avoid implicit type conversion.
  */
-static inline __must_check size_t __ab_c_size(size_t a, size_t b, size_t c)
+static inline size_t __must_check size_sub(size_t minuend, size_t subtrahend)
 {
 	size_t bytes;
 
-	if (check_mul_overflow(a, b, &bytes))
-		return SIZE_MAX;
-	if (check_add_overflow(bytes, c, &bytes))
+	if (minuend == SIZE_MAX || subtrahend == SIZE_MAX ||
+	    check_sub_overflow(minuend, subtrahend, &bytes))
 		return SIZE_MAX;
 
 	return bytes;
 }
 
 /**
- * struct_size() - Calculate size of structure with trailing array.
- * @p: Pointer to the structure.
- * @member: Name of the array member.
- * @count: Number of elements in the array.
+ * array_size() - Calculate size of 2-dimensional array.
  *
- * Calculates size of memory needed for structure @p followed by an
- * array of @count number of @member elements.
+ * @a: dimension one
+ * @b: dimension two
  *
- * Return: number of bytes needed or SIZE_MAX on overflow.
+ * Calculates size of 2-dimensional array: @a * @b.
+ *
+ * Returns: number of bytes needed to represent the array or SIZE_MAX on
+ * overflow.
  */
-#define struct_size(p, member, count)					\
-	__ab_c_size(count,						\
-		    sizeof(*(p)->member) + __must_be_array((p)->member),\
-		    sizeof(*(p)))
+#define array_size(a, b)	size_mul(a, b)
+
+/**
+ * array3_size() - Calculate size of 3-dimensional array.
+ *
+ * @a: dimension one
+ * @b: dimension two
+ * @c: dimension three
+ *
+ * Calculates size of 3-dimensional array: @a * @b * @c.
+ *
+ * Returns: number of bytes needed to represent the array or SIZE_MAX on
+ * overflow.
+ */
+#define array3_size(a, b, c)	size_mul(size_mul(a, b), c)
 
 /**
  * flex_array_size() - Calculate size of a flexible array member
@@ -208,7 +230,22 @@
  * Return: number of bytes needed or SIZE_MAX on overflow.
  */
 #define flex_array_size(p, member, count)				\
-	array_size(count,						\
-		    sizeof(*(p)->member) + __must_be_array((p)->member))
+	size_mul(count,							\
+		 sizeof(*(p)->member) + __must_be_array((p)->member))
+
+/**
+ * struct_size() - Calculate size of structure with trailing flexible array.
+ *
+ * @p: Pointer to the structure.
+ * @member: Name of the array member.
+ * @count: Number of elements in the array.
+ *
+ * Calculates size of memory needed for structure @p followed by an
+ * array of @count number of @member elements.
+ *
+ * Return: number of bytes needed or SIZE_MAX on overflow.
+ */
+#define struct_size(p, member, count)					\
+	size_add(sizeof(*(p)), flex_array_size(p, member, count))
 
 #endif /* __LINUX_OVERFLOW_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pagemap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pagemap.h
@@ -733,61 +733,11 @@
 extern void add_page_wait_queue(struct page *page, wait_queue_entry_t *waiter);
 
 /*
- * Fault everything in given userspace address range in.
+ * Fault in userspace address range.
  */
-static inline int fault_in_pages_writeable(char __user *uaddr, size_t size)
-{
-	char __user *end = uaddr + size - 1;
-
-	if (unlikely(size == 0))
-		return 0;
-
-	if (unlikely(uaddr > end))
-		return -EFAULT;
-	/*
-	 * Writing zeroes into userspace here is OK, because we know that if
-	 * the zero gets there, we'll be overwriting it.
-	 */
-	do {
-		if (unlikely(__put_user(0, uaddr) != 0))
-			return -EFAULT;
-		uaddr += PAGE_SIZE;
-	} while (uaddr <= end);
-
-	/* Check whether the range spilled into the next page. */
-	if (((unsigned long)uaddr & PAGE_MASK) ==
-			((unsigned long)end & PAGE_MASK))
-		return __put_user(0, end);
-
-	return 0;
-}
-
-static inline int fault_in_pages_readable(const char __user *uaddr, size_t size)
-{
-	volatile char c;
-	const char __user *end = uaddr + size - 1;
-
-	if (unlikely(size == 0))
-		return 0;
-
-	if (unlikely(uaddr > end))
-		return -EFAULT;
-
-	do {
-		if (unlikely(__get_user(c, uaddr) != 0))
-			return -EFAULT;
-		uaddr += PAGE_SIZE;
-	} while (uaddr <= end);
-
-	/* Check whether the range spilled into the next page. */
-	if (((unsigned long)uaddr & PAGE_MASK) ==
-			((unsigned long)end & PAGE_MASK)) {
-		return __get_user(c, end);
-	}
-
-	(void)c;
-	return 0;
-}
+size_t fault_in_writeable(char __user *uaddr, size_t size);
+size_t fault_in_safe_writeable(const char __user *uaddr, size_t size);
+size_t fault_in_readable(const char __user *uaddr, size_t size);
 
 int add_to_page_cache_locked(struct page *page, struct address_space *mapping,
 				pgoff_t index, gfp_t gfp_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/panic.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/panic.h
@@ -11,16 +11,11 @@
 __printf(1, 2)
 void panic(const char *fmt, ...) __noreturn __cold;
 void nmi_panic(struct pt_regs *regs, const char *msg);
+void check_panic_on_warn(const char *origin);
 extern void oops_enter(void);
 extern void oops_exit(void);
 extern bool oops_may_print(void);
 
-#ifdef CONFIG_SMP
-extern unsigned int sysctl_oops_all_cpu_backtrace;
-#else
-#define sysctl_oops_all_cpu_backtrace 0
-#endif /* CONFIG_SMP */
-
 extern int panic_timeout;
 extern unsigned long panic_print;
 extern int panic_on_oops;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/part_stat.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/part_stat.h
@@ -3,6 +3,7 @@
 #define _LINUX_PART_STAT_H
 
 #include <linux/genhd.h>
+#include <asm/local.h>
 
 struct disk_stats {
 	u64 nsecs[NR_STAT_GROUPS];
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pci.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pci.h
@@ -155,6 +155,15 @@
 #define PCI_NUM_INTX	4
 
 /*
+ * Reading from a device that doesn't respond typically returns ~0.  A
+ * successful read from a device may also return ~0, so you need additional
+ * information to reliably identify errors.
+ */
+#define PCI_ERROR_RESPONSE		(~0ULL)
+#define PCI_SET_ERROR_RESPONSE(val)	(*(val) = ((typeof(*(val))) PCI_ERROR_RESPONSE))
+#define PCI_POSSIBLE_ERROR(val)		((val) == ((typeof(val)) PCI_ERROR_RESPONSE))
+
+/*
  * pci_power_t values must match the bits in the Capabilities PME_Support
  * and Control/Status PowerState fields in the Power Management capability.
  */
@@ -233,6 +242,10 @@
 	PCI_DEV_FLAGS_NO_FLR_RESET = (__force pci_dev_flags_t) (1 << 10),
 	/* Don't use Relaxed Ordering for TLPs directed at this device */
 	PCI_DEV_FLAGS_NO_RELAXED_ORDERING = (__force pci_dev_flags_t) (1 << 11),
+	/* Enable ASPM regardless of how LnkCtl is programmed */
+	PCI_DEV_FLAGS_ENABLE_ASPM = (__force pci_dev_flags_t) (1 << 12),
+	/* Device does honor MSI masking despite saying otherwise */
+	PCI_DEV_FLAGS_HAS_MSI_MASKING = (__force pci_dev_flags_t) (1 << 13),
 };
 
 enum pci_irq_reroute_variant {
@@ -453,6 +466,7 @@
 	unsigned int	link_active_reporting:1;/* Device capable of reporting link active */
 	unsigned int	no_vf_scan:1;		/* Don't scan for VFs after IOV enablement */
 	unsigned int	no_command_memory:1;	/* No PCI_COMMAND_MEMORY */
+	unsigned int	rom_bar_overlap:1;	/* ROM BAR disable broken */
 	pci_dev_flags_t dev_flags;
 	atomic_t	enable_cnt;	/* pci_enable_device has been called */
 
@@ -466,6 +480,7 @@
 	unsigned int	broken_cmd_compl:1;	/* No compl for some cmds */
 #endif
 #ifdef CONFIG_PCIE_PTM
+	u16		ptm_cap;		/* PTM Capability */
 	unsigned int	ptm_root:1;
 	unsigned int	ptm_enabled:1;
 	u8		ptm_granularity;
@@ -555,6 +570,7 @@
 	void		*release_data;
 	unsigned int	ignore_reset_delay:1;	/* For entire hierarchy */
 	unsigned int	no_ext_tags:1;		/* No Extended Tags */
+	unsigned int	no_inc_mrrs:1;		/* No Increase MRRS */
 	unsigned int	native_aer:1;		/* OS may use PCIe AER */
 	unsigned int	native_pcie_hotplug:1;	/* OS may use PCIe hotplug */
 	unsigned int	native_shpc_hotplug:1;	/* OS may use SHPC hotplug */
@@ -654,6 +670,7 @@
 	struct bin_attribute	*legacy_io;	/* Legacy I/O for this bus */
 	struct bin_attribute	*legacy_mem;	/* Legacy mem */
 	unsigned int		is_added:1;
+	unsigned int		unsafe_warn:1;	/* warned about RW1C config write */
 };
 
 #define to_pci_bus(n)	container_of(n, struct pci_bus, dev)
@@ -1386,6 +1403,7 @@
 			  unsigned int flags);
 struct resource *pci_bus_resource_n(const struct pci_bus *bus, int n);
 void pci_bus_remove_resources(struct pci_bus *bus);
+void pci_bus_remove_resource(struct pci_bus *bus, struct resource *res);
 int devm_request_pci_bus_resources(struct device *dev,
 				   struct list_head *resources);
 
@@ -1639,6 +1657,7 @@
 void pcie_no_aspm(void);
 bool pcie_aspm_support_enabled(void);
 bool pcie_aspm_enabled(struct pci_dev *pdev);
+bool pcie_aspm_capable(struct pci_dev *pdev);
 #else
 static inline int pci_disable_link_state(struct pci_dev *pdev, int state)
 { return 0; }
@@ -1647,6 +1666,7 @@
 static inline void pcie_no_aspm(void) { }
 static inline bool pcie_aspm_support_enabled(void) { return false; }
 static inline bool pcie_aspm_enabled(struct pci_dev *pdev) { return false; }
+static inline bool pcie_aspm_capable(struct pci_dev *pdev) { return false; }
 #endif
 
 #ifdef CONFIG_PCIEAER
@@ -1659,10 +1679,12 @@
 
 #ifdef CONFIG_PCIE_PTM
 int pci_enable_ptm(struct pci_dev *dev, u8 *granularity);
+void pci_disable_ptm(struct pci_dev *dev);
 bool pcie_ptm_enabled(struct pci_dev *dev);
 #else
 static inline int pci_enable_ptm(struct pci_dev *dev, u8 *granularity)
 { return -EINVAL; }
+static inline void pci_disable_ptm(struct pci_dev *dev) { }
 static inline bool pcie_ptm_enabled(struct pci_dev *dev)
 { return false; }
 #endif
@@ -1671,6 +1693,7 @@
 bool pci_cfg_access_trylock(struct pci_dev *dev);
 void pci_cfg_access_unlock(struct pci_dev *dev);
 
+void pci_dev_lock(struct pci_dev *dev);
 int pci_dev_trylock(struct pci_dev *dev);
 void pci_dev_unlock(struct pci_dev *dev);
 
@@ -1782,6 +1805,7 @@
 #define pci_dev_put(dev)	do { } while (0)
 
 static inline void pci_set_master(struct pci_dev *dev) { }
+static inline void pci_clear_master(struct pci_dev *dev) { }
 static inline int pci_enable_device(struct pci_dev *dev) { return -EIO; }
 static inline void pci_disable_device(struct pci_dev *dev) { }
 static inline int pcim_enable_device(struct pci_dev *pdev) { return -EIO; }
@@ -2278,6 +2302,11 @@
 	return NULL;
 }
 
+static inline bool pci_dev_is_disconnected(const struct pci_dev *dev)
+{
+	return dev->error_state == pci_channel_io_perm_failure;
+}
+
 void pci_request_acs(void);
 bool pci_acs_enabled(struct pci_dev *pdev, u16 acs_flags);
 bool pci_acs_path_enabled(struct pci_dev *start,
@@ -2382,6 +2411,12 @@
 static inline bool pci_pr3_present(struct pci_dev *pdev) { return false; }
 #endif
 
+#if defined(CONFIG_X86) && defined(CONFIG_ACPI)
+bool arch_pci_dev_is_removable(struct pci_dev *pdev);
+#else
+static inline bool arch_pci_dev_is_removable(struct pci_dev *pdev) { return false; }
+#endif
+
 #ifdef CONFIG_EEH
 static inline struct eeh_dev *pci_dev_to_eeh_dev(struct pci_dev *pdev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pci_ids.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pci_ids.h
@@ -60,6 +60,8 @@
 #define PCI_CLASS_BRIDGE_EISA		0x0602
 #define PCI_CLASS_BRIDGE_MC		0x0603
 #define PCI_CLASS_BRIDGE_PCI		0x0604
+#define PCI_CLASS_BRIDGE_PCI_NORMAL		0x060400
+#define PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE	0x060401
 #define PCI_CLASS_BRIDGE_PCMCIA		0x0605
 #define PCI_CLASS_BRIDGE_NUBUS		0x0606
 #define PCI_CLASS_BRIDGE_CARDBUS	0x0607
@@ -554,7 +556,9 @@
 #define PCI_DEVICE_ID_AMD_17H_M30H_DF_F3 0x1493
 #define PCI_DEVICE_ID_AMD_17H_M60H_DF_F3 0x144b
 #define PCI_DEVICE_ID_AMD_17H_M70H_DF_F3 0x1443
+#define PCI_DEVICE_ID_AMD_VANGOGH_USB	0x163a
 #define PCI_DEVICE_ID_AMD_19H_DF_F3	0x1653
+#define PCI_DEVICE_ID_AMD_19H_M10H_DF_F3 0x14b0
 #define PCI_DEVICE_ID_AMD_19H_M40H_DF_F3 0x167c
 #define PCI_DEVICE_ID_AMD_19H_M50H_DF_F3 0x166d
 #define PCI_DEVICE_ID_AMD_CNB17H_F3	0x1703
@@ -1740,6 +1744,10 @@
 #define PCI_SUBDEVICE_ID_AT_2700FX	0x2701
 #define PCI_SUBDEVICE_ID_AT_2701FX	0x2703
 
+#define PCI_VENDOR_ID_ASIX		0x125b
+#define PCI_DEVICE_ID_ASIX_AX99100	0x9100
+#define PCI_DEVICE_ID_ASIX_AX99100_LB	0x9110
+
 #define PCI_VENDOR_ID_ESS		0x125d
 #define PCI_DEVICE_ID_ESS_ESS1968	0x1968
 #define PCI_DEVICE_ID_ESS_ESS1978	0x1978
@@ -2110,6 +2118,8 @@
 
 #define PCI_VENDOR_ID_CHELSIO		0x1425
 
+#define PCI_VENDOR_ID_EDIMAX		0x1432
+
 #define PCI_VENDOR_ID_ADLINK		0x144a
 
 #define PCI_VENDOR_ID_SAMSUNG		0x144d
@@ -2630,6 +2640,8 @@
 #define PCI_DEVICE_ID_DCI_PCCOM8	0x0002
 #define PCI_DEVICE_ID_DCI_PCCOM2	0x0004
 
+#define PCI_VENDOR_ID_GLENFLY		0x6766
+
 #define PCI_VENDOR_ID_INTEL		0x8086
 #define PCI_DEVICE_ID_INTEL_EESSC	0x0008
 #define PCI_DEVICE_ID_INTEL_PXHD_0	0x0320
@@ -2658,7 +2670,9 @@
 #define PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB	0x095E
 #define PCI_DEVICE_ID_INTEL_I960	0x0960
 #define PCI_DEVICE_ID_INTEL_I960RM	0x0962
+#define PCI_DEVICE_ID_INTEL_DSA_SPR0	0x0b25
 #define PCI_DEVICE_ID_INTEL_CENTERTON_ILB	0x0c60
+#define PCI_DEVICE_ID_INTEL_IAX_SPR0	0x0cfe
 #define PCI_DEVICE_ID_INTEL_8257X_SOL	0x1062
 #define PCI_DEVICE_ID_INTEL_82573E_SOL	0x1085
 #define PCI_DEVICE_ID_INTEL_82573L_SOL	0x108F
@@ -2996,6 +3010,7 @@
 #define PCI_DEVICE_ID_INTEL_82443GX_0	0x71a0
 #define PCI_DEVICE_ID_INTEL_82443GX_2	0x71a2
 #define PCI_DEVICE_ID_INTEL_82372FB_1	0x7601
+#define PCI_DEVICE_ID_INTEL_HDA_ARL	0x7728
 #define PCI_DEVICE_ID_INTEL_SCH_LPC	0x8119
 #define PCI_DEVICE_ID_INTEL_SCH_IDE	0x811a
 #define PCI_DEVICE_ID_INTEL_E6XX_CU	0x8183
@@ -3010,6 +3025,8 @@
 #define PCI_DEVICE_ID_INTEL_VMD_9A0B	0x9a0b
 #define PCI_DEVICE_ID_INTEL_S21152BB	0xb152
 
+#define PCI_VENDOR_ID_WANGXUN		0x8088
+
 #define PCI_VENDOR_ID_SCALEMP		0x8686
 #define PCI_DEVICE_ID_SCALEMP_VSMP_CTL	0x1010
 
@@ -3090,6 +3107,8 @@
 
 #define PCI_VENDOR_ID_3COM_2		0xa727
 
+#define PCI_VENDOR_ID_SOLIDRUN		0xd063
+
 #define PCI_VENDOR_ID_DIGIUM		0xd161
 #define PCI_DEVICE_ID_DIGIUM_HFC4S	0xb410
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/percpu_counter.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/percpu_counter.h
@@ -15,6 +15,9 @@
 #include <linux/types.h>
 #include <linux/gfp.h>
 
+/* percpu_counter batch for local add or sub */
+#define PERCPU_COUNTER_LOCAL_BATCH	INT_MAX
+
 #ifdef CONFIG_SMP
 
 struct percpu_counter {
@@ -56,6 +59,22 @@
 	percpu_counter_add_batch(fbc, amount, percpu_counter_batch);
 }
 
+/*
+ * With percpu_counter_add_local() and percpu_counter_sub_local(), counts
+ * are accumulated in local per cpu counter and not in fbc->count until
+ * local count overflows PERCPU_COUNTER_LOCAL_BATCH. This makes counter
+ * write efficient.
+ * But percpu_counter_sum(), instead of percpu_counter_read(), needs to be
+ * used to add up the counts from each CPU to account for all the local
+ * counts. So percpu_counter_add_local() and percpu_counter_sub_local()
+ * should be used when a counter is updated frequently and read rarely.
+ */
+static inline void
+percpu_counter_add_local(struct percpu_counter *fbc, s64 amount)
+{
+	percpu_counter_add_batch(fbc, amount, PERCPU_COUNTER_LOCAL_BATCH);
+}
+
 static inline s64 percpu_counter_sum_positive(struct percpu_counter *fbc)
 {
 	s64 ret = __percpu_counter_sum(fbc);
@@ -138,6 +157,13 @@
 	preempt_enable();
 }
 
+/* non-SMP percpu_counter_add_local is the same with percpu_counter_add */
+static inline void
+percpu_counter_add_local(struct percpu_counter *fbc, s64 amount)
+{
+	percpu_counter_add(fbc, amount);
+}
+
 static inline void
 percpu_counter_add_batch(struct percpu_counter *fbc, s64 amount, s32 batch)
 {
@@ -193,4 +219,10 @@
 	percpu_counter_add(fbc, -amount);
 }
 
+static inline void
+percpu_counter_sub_local(struct percpu_counter *fbc, s64 amount)
+{
+	percpu_counter_add_local(fbc, -amount);
+}
+
 #endif /* _LINUX_PERCPU_COUNTER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/perf_event.h
@@ -661,6 +661,7 @@
 	/* The cumulative AND of all event_caps for events in this group. */
 	int				group_caps;
 
+	unsigned int			group_generation;
 	struct perf_event		*group_leader;
 	struct pmu			*pmu;
 	void				*pmu_private;
@@ -680,18 +681,6 @@
 	u64				total_time_running;
 	u64				tstamp;
 
-	/*
-	 * timestamp shadows the actual context timing but it can
-	 * be safely used in NMI interrupt context. It reflects the
-	 * context time as it was when the event was last scheduled in,
-	 * or when ctx_sched_in failed to schedule the event because we
-	 * run out of PMC.
-	 *
-	 * ctx_time already accounts for ctx->timestamp. Therefore to
-	 * compute ctx_time for a sample, simply add perf_clock().
-	 */
-	u64				shadow_ctx_time;
-
 	struct perf_event_attr		attr;
 	u16				header_size;
 	u16				id_header_size;
@@ -735,11 +724,15 @@
 	struct fasync_struct		*fasync;
 
 	/* delayed work for NMIs and such */
-	int				pending_wakeup;
-	int				pending_kill;
-	int				pending_disable;
+	unsigned int			pending_wakeup;
+	unsigned int			pending_kill;
+	unsigned int			pending_disable;
+	unsigned int			pending_sigtrap;
 	unsigned long			pending_addr;	/* SIGTRAP */
-	struct irq_work			pending;
+	struct irq_work			pending_irq;
+	struct callback_head		pending_task;
+	unsigned int			pending_work;
+	struct rcuwait			pending_work_wait;
 
 	atomic_t			event_limit;
 
@@ -758,6 +751,8 @@
 	struct pid_namespace		*ns;
 	u64				id;
 
+	atomic64_t			lost_samples;
+
 	u64				(*clock)(void);
 	perf_overflow_handler_t		overflow_handler;
 	void				*overflow_handler_context;
@@ -838,6 +833,7 @@
 	 */
 	u64				time;
 	u64				timestamp;
+	u64				timeoffset;
 
 	/*
 	 * These fields let us detect when two contexts have both
@@ -852,6 +848,14 @@
 #endif
 	void				*task_ctx_data; /* pmu specific data */
 	struct rcu_head			rcu_head;
+
+	/*
+	 * Sum (event->pending_sigtrap + event->pending_work)
+	 *
+	 * The SIGTRAP is targeted at ctx->task, as such it won't do changing
+	 * that until the signal is delivered.
+	 */
+	local_t				nr_pending;
 };
 
 /*
@@ -920,6 +924,8 @@
 struct perf_cgroup_info {
 	u64				time;
 	u64				timestamp;
+	u64				timeoffset;
+	int				active;
 };
 
 struct perf_cgroup {
@@ -1082,15 +1088,31 @@
 			     struct pt_regs *regs);
 
 static inline bool
-is_default_overflow_handler(struct perf_event *event)
+__is_default_overflow_handler(perf_overflow_handler_t overflow_handler)
 {
-	if (likely(event->overflow_handler == perf_event_output_forward))
+	if (likely(overflow_handler == perf_event_output_forward))
 		return true;
-	if (unlikely(event->overflow_handler == perf_event_output_backward))
+	if (unlikely(overflow_handler == perf_event_output_backward))
 		return true;
 	return false;
 }
 
+#define is_default_overflow_handler(event) \
+	__is_default_overflow_handler((event)->overflow_handler)
+
+#ifdef CONFIG_BPF_SYSCALL
+static inline bool uses_default_overflow_handler(struct perf_event *event)
+{
+	if (likely(is_default_overflow_handler(event)))
+		return true;
+
+	return __is_default_overflow_handler(event->orig_overflow_handler);
+}
+#else
+#define uses_default_overflow_handler(event) \
+	is_default_overflow_handler(event)
+#endif
+
 extern void
 perf_event_header__init_id(struct perf_event_header *header,
 			   struct perf_sample_data *data,
@@ -1239,7 +1261,18 @@
 				 enum perf_bpf_event_type type,
 				 u16 flags);
 
-extern struct perf_guest_info_callbacks *perf_guest_cbs;
+extern struct perf_guest_info_callbacks __rcu *perf_guest_cbs;
+static inline struct perf_guest_info_callbacks *perf_get_guest_cbs(void)
+{
+	/*
+	 * Callbacks are RCU-protected and must be READ_ONCE to avoid reloading
+	 * the callbacks between a !NULL check and dereferences, to ensure
+	 * pending stores/changes to the callback pointers are visible before a
+	 * non-NULL perf_guest_cbs is visible to readers, and to prevent a
+	 * module from unloading callbacks while readers are active.
+	 */
+	return rcu_dereference(perf_guest_cbs);
+}
 extern int perf_register_guest_info_callbacks(struct perf_guest_info_callbacks *callbacks);
 extern int perf_unregister_guest_info_callbacks(struct perf_guest_info_callbacks *callbacks);
 
@@ -1314,6 +1347,12 @@
 #define PERF_SECURITY_CPU		1
 #define PERF_SECURITY_KERNEL		2
 #define PERF_SECURITY_TRACEPOINT	3
+#define PERF_SECURITY_MAX		4
+
+static inline bool perf_paranoid_any(void)
+{
+	return sysctl_perf_event_paranoid >= PERF_SECURITY_MAX;
+}
 
 static inline int perf_is_paranoid(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pgtable.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pgtable.h
@@ -62,6 +62,7 @@
 {
 	return (address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1);
 }
+#define pte_index pte_index
 
 #ifndef pmd_index
 static inline unsigned long pmd_index(unsigned long address)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/phy.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/phy.h
@@ -536,6 +536,10 @@
  * @mdix: Current crossover
  * @mdix_ctrl: User setting of crossover
  * @interrupts: Flag interrupts have been enabled
+ * @irq_suspended: Flag indicating PHY is suspended and therefore interrupt
+ *                 handling shall be postponed until PHY has resumed
+ * @irq_rerun: Flag indicating interrupts occurred while PHY was suspended,
+ *             requiring a rerun of the interrupt handler after resume
  * @interface: enum phy_interface_t value
  * @skb: Netlink message for cable diagnostics
  * @nest: Netlink nest used for cable diagnostics
@@ -590,6 +594,8 @@
 
 	/* Interrupts are enabled */
 	unsigned interrupts:1;
+	unsigned irq_suspended:1;
+	unsigned irq_rerun:1;
 
 	enum phy_state state;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/phy/phy-hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/phy/phy-hdmi.h
@@ -0,0 +1,211 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __PHY_HDMI_H_
+#define __PHY_HDMI_H_
+
+#include <linux/types.h>
+
+/**
+ * enum callback_type - HDMI PHY callback functions type
+ * This enumerates the list of available HDMI PHY callback functions types.
+ *
+ * @RX_INIT_CB:		Receiver initialization callback type
+ * @RX_READY_CB:	Receiver ready callback type
+ * @TX_INIT_CB:		Transmitter initialization callback type
+ * @TX_READY_CB:	Transmitter ready callback type
+ */
+enum callback_type {
+	RX_INIT_CB,
+	RX_READY_CB,
+	TX_INIT_CB,
+	TX_READY_CB,
+};
+
+/**
+ * struct hdmiphy_callback - HDMI PHY callback structure
+ * This structure is used to represent the callback function of a
+ * HDMI phy.
+ *
+ * @cb:		Callback function pointer
+ * @data:	Pointer to store data
+ * @type:	Callback type
+ */
+struct hdmiphy_callback {
+	void (*cb)(void *callback_func);
+	void *data;
+	u32 type;
+};
+
+/**
+ * struct phy_configure_opts_hdmi - HDMI PHY configuration set
+ *
+ * This structure is used to represent the configuration state of a
+ * HDMI phy.
+ */
+struct phy_configure_opts_hdmi {
+	/**
+	 * @tmdsclock_ratio_flag:
+	 *
+	 * SCDC tmds clock ratio flag.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 tmdsclock_ratio_flag : 1;
+	/**
+	 * @tmdsclock_ratio:
+	 *
+	 * SCDC tmds clock ratio bit.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 tmdsclock_ratio : 1;
+
+	/**
+	 * @ibufds:
+	 *
+	 * Flag to enable/disable the TX or RX IBUFDS configuration.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 ibufds : 1;
+	/**
+	 * @ibufds_en:
+	 *
+	 * enables/disable the TX or RX IBUFDS peripheral.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 ibufds_en : 1;
+	/**
+	 * @clkout1_obuftds:
+	 *
+	 * Flag to enable/disable the TX or RX CLKOUT1 OBUFTDS configuration.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 clkout1_obuftds : 1;
+	/**
+	 * @clkout1_obuftds_en:
+	 *
+	 * enable/disable the TX or RX CLKOUT1 OBUFTDS peripheral.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 clkout1_obuftds_en : 1;
+	/**
+	 * @config_hdmi20:
+	 *
+	 * Flag to enable/disable HDMI-PHY to be configured in 2.0 mode
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 config_hdmi20 : 1;
+	/**
+	 * @config_hdmi21:
+	 *
+	 * Flag to enable/disable HDMI-PHY to be configured in 2.1 mode
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 config_hdmi21 : 1;
+	/**
+	 * @linerate:
+	 *
+	 * Supported linerates(in Gb/s) to be configured in FRL mode.
+	 *
+	 * Allowed values: 3, 6, 8. 10, 12
+	 */
+	u64 linerate;
+	/**
+	 * @nchannels:
+	 *
+	 * No of channels to confiure in FRL mode.
+	 *
+	 * Allowed values: 3, 4
+	 */
+	u8 nchannels;
+	/**
+	 * @rx_get_refclk:
+	 *
+	 * Flag to get the rx reference clock value from the PHY driver
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 rx_get_refclk : 1;
+	/**
+	 * @rx_refclk_hz:
+	 *
+	 * Rx reference clock value.
+	 *
+	 */
+	unsigned long rx_refclk_hz;
+	/**
+	 * @phycb:
+	 *
+	 * phy callback functions flag.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 phycb : 1;
+	/**
+	 * @hdmiphycb:
+	 *
+	 * HDMI PHY callback structure
+	 */
+	struct hdmiphy_callback hdmiphycb;
+	/**
+	 * @tx_params:
+	 *
+	 * Flag to update the tx stream paramerters.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 tx_params : 1;
+	/**
+	 * @cal_mmcm_param:
+	 *
+	 * Flage to update caliculate mmcm parameters.
+	 *
+	 * Allowed values: 0, 1
+	 */
+	u8 cal_mmcm_param : 1;
+	/**
+	 * @tx_tmdsclk:
+	 *
+	 * TX TMDS clock value.
+	 *
+	 */
+	u64 tx_tmdsclk;
+	/**
+	 * @ppc:
+	 *
+	 * pixels per clock.
+	 *
+	 * Allowed values: 1, 2, 4, 8
+	 */
+	u8 ppc;
+	/**
+	 * @bpc:
+	 *
+	 * bits per component.
+	 *
+	 * Allowed  values: 8, 10, 23, 16
+	 */
+	u8 bpc;
+	/**
+	 * @fmt:
+	 *
+	 * color format.
+	 *
+	 * Allowed values: 0, 1, 2, 3
+	 */
+	u8 fmt;
+	/**
+	 * @reset_gt:
+	 *
+	 * Flag to reset the GT
+	 */
+	u8 reset_gt : 1;
+};
+
+#endif /* __PHY_HDMI_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/phy/phy.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/phy/phy.h
@@ -17,6 +17,7 @@
 #include <linux/regulator/consumer.h>
 
 #include <linux/phy/phy-dp.h>
+#include <linux/phy/phy-hdmi.h>
 #include <linux/phy/phy-mipi-dphy.h>
 
 struct phy;
@@ -57,10 +58,13 @@
  *		the MIPI_DPHY phy mode.
  * @dp:		Configuration set applicable for phys supporting
  *		the DisplayPort protocol.
+ * @hdmi:	Configuration set applicable for phys supporting
+ *		the HDMI protocol.
  */
 union phy_configure_opts {
 	struct phy_configure_opts_mipi_dphy	mipi_dphy;
 	struct phy_configure_opts_dp		dp;
+	struct phy_configure_opts_hdmi		hdmi;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/phy/tegra/xusb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/phy/tegra/xusb.h
@@ -24,6 +24,7 @@
 int tegra_phy_xusb_utmi_port_reset(struct phy *phy);
 int tegra_xusb_padctl_get_usb3_companion(struct tegra_xusb_padctl *padctl,
 					 unsigned int port);
+int tegra_xusb_padctl_get_port_number(struct phy *phy);
 int tegra_xusb_padctl_enable_phy_sleepwalk(struct tegra_xusb_padctl *padctl, struct phy *phy,
 					   enum usb_device_speed speed);
 int tegra_xusb_padctl_disable_phy_sleepwalk(struct tegra_xusb_padctl *padctl, struct phy *phy);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/phylink.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/phylink.h
@@ -64,6 +64,7 @@
  * @pcs_poll: MAC PCS cannot provide link change interrupt
  * @poll_fixed_state: if true, starts link_poll,
  *		      if MAC link is at %MLO_AN_FIXED mode.
+ * @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM.
  * @ovr_an_inband: if true, override PCS to MLO_AN_INBAND
  * @get_fixed_state: callback to execute to determine the fixed link state,
  *		     if MAC link is at %MLO_AN_FIXED mode.
@@ -73,6 +74,7 @@
 	enum phylink_op_type type;
 	bool pcs_poll;
 	bool poll_fixed_state;
+	bool mac_managed_pm;
 	bool ovr_an_inband;
 	void (*get_fixed_state)(struct phylink_config *config,
 				struct phylink_link_state *state);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pipe_fs_i.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pipe_fs_i.h
@@ -71,7 +71,7 @@
 	unsigned int files;
 	unsigned int r_counter;
 	unsigned int w_counter;
-	unsigned int poll_usage;
+	bool poll_usage;
 	struct page *tmp_page;
 	struct fasync_struct *fasync_readers;
 	struct fasync_struct *fasync_writers;
@@ -125,6 +125,22 @@
 };
 
 /**
+ * pipe_has_watch_queue - Check whether the pipe is a watch_queue,
+ * i.e. it was created with O_NOTIFICATION_PIPE
+ * @pipe: The pipe to check
+ *
+ * Return: true if pipe is a watch queue, false otherwise.
+ */
+static inline bool pipe_has_watch_queue(const struct pipe_inode_info *pipe)
+{
+#ifdef CONFIG_WATCH_QUEUE
+	return pipe->watch_queue != NULL;
+#else
+	return false;
+#endif
+}
+
+/**
  * pipe_empty - Return true if the pipe is empty
  * @head: The pipe ring head pointer
  * @tail: The pipe ring tail pointer
@@ -229,6 +245,15 @@
 	return buf->ops->try_steal(pipe, buf);
 }
 
+static inline void pipe_discard_from(struct pipe_inode_info *pipe,
+		unsigned int old_head)
+{
+	unsigned int mask = pipe->ring_size - 1;
+
+	while (pipe->head > old_head)
+		pipe_buf_release(pipe, &pipe->bufs[--pipe->head & mask]);
+}
+
 /* Differs from PIPE_BUF in that PIPE_SIZE is the length of the actual
    memory allocation, whereas PIPE_BUF makes atomicity guarantees.  */
 #define PIPE_SIZE		PAGE_SIZE
@@ -256,18 +281,14 @@
 
 extern const struct pipe_buf_operations nosteal_pipe_buf_ops;
 
-#ifdef CONFIG_WATCH_QUEUE
 unsigned long account_pipe_buffers(struct user_struct *user,
 				   unsigned long old, unsigned long new);
 bool too_many_pipe_buffers_soft(unsigned long user_bufs);
 bool too_many_pipe_buffers_hard(unsigned long user_bufs);
 bool pipe_is_unprivileged_user(void);
-#endif
 
 /* for F_SETPIPE_SZ and F_GETPIPE_SZ */
-#ifdef CONFIG_WATCH_QUEUE
 int pipe_resize_ring(struct pipe_inode_info *pipe, unsigned int nr_slots);
-#endif
 long pipe_fcntl(struct file *, unsigned int, unsigned long arg);
 struct pipe_inode_info *get_pipe_info(struct file *file, bool for_splice);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_data/cros_ec_proto.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_data/cros_ec_proto.h
@@ -216,6 +216,9 @@
 int cros_ec_check_result(struct cros_ec_device *ec_dev,
 			 struct cros_ec_command *msg);
 
+int cros_ec_cmd_xfer(struct cros_ec_device *ec_dev,
+		     struct cros_ec_command *msg);
+
 int cros_ec_cmd_xfer_status(struct cros_ec_device *ec_dev,
 			    struct cros_ec_command *msg);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_data/ti-sysc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_data/ti-sysc.h
@@ -50,6 +50,7 @@
 	s8 emufree_shift;
 };
 
+#define SYSC_QUIRK_REINIT_ON_CTX_LOST	BIT(28)
 #define SYSC_QUIRK_REINIT_ON_RESUME	BIT(27)
 #define SYSC_QUIRK_GPMC_DEBUG		BIT(26)
 #define SYSC_MODULE_QUIRK_ENA_RESETDONE	BIT(25)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_data/x86/asus-wmi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_data/x86/asus-wmi.h
@@ -64,6 +64,7 @@
 #define ASUS_WMI_DEVID_PANEL_OD		0x00050019
 #define ASUS_WMI_DEVID_CAMERA		0x00060013
 #define ASUS_WMI_DEVID_LID_FLIP		0x00060062
+#define ASUS_WMI_DEVID_LID_FLIP_ROG	0x00060077
 
 /* Storage */
 #define ASUS_WMI_DEVID_CARDREADER	0x00080013
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_data/x86/intel-spi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_data/x86/intel-spi.h
@@ -19,11 +19,13 @@
 /**
  * struct intel_spi_boardinfo - Board specific data for Intel SPI driver
  * @type: Type which this controller is compatible with
- * @writeable: The chip is writeable
+ * @set_writeable: Try to make the chip writeable (optional)
+ * @data: Data to be passed to @set_writeable can be %NULL
  */
 struct intel_spi_boardinfo {
 	enum intel_spi_type type;
-	bool writeable;
+	bool (*set_writeable)(void __iomem *base, void *data);
+	void *data;
 };
 
 #endif /* INTEL_SPI_PDATA_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_data/x86/pmc_atom.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_data/x86/pmc_atom.h
@@ -7,6 +7,8 @@
 #ifndef PMC_ATOM_H
 #define PMC_ATOM_H
 
+#include <linux/bits.h>
+
 /* ValleyView Power Control Unit PCI Device ID */
 #define	PCI_DEVICE_ID_VLV_PMC	0x0F1C
 /* CherryTrail Power Control Unit PCI Device ID */
@@ -139,9 +141,9 @@
 #define	ACPI_MMIO_REG_LEN	0x100
 
 #define	PM1_CNT			0x4
-#define	SLEEP_TYPE_MASK		0xFFFFECFF
+#define	SLEEP_TYPE_MASK		GENMASK(12, 10)
 #define	SLEEP_TYPE_S5		0x1C00
-#define	SLEEP_ENABLE		0x2000
+#define	SLEEP_ENABLE		BIT(13)
 
 extern int pmc_atom_read(int offset, u32 *value);
 extern int pmc_atom_write(int offset, u32 value);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_data/x86/soc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_data/x86/soc.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Helpers for Intel SoC model detection
+ *
+ * Copyright (c) 2019, Intel Corporation.
+ */
+
+#ifndef __PLATFORM_DATA_X86_SOC_H
+#define __PLATFORM_DATA_X86_SOC_H
+
+#if IS_ENABLED(CONFIG_X86)
+
+#include <asm/cpu_device_id.h>
+#include <asm/intel-family.h>
+
+#define SOC_INTEL_IS_CPU(soc, type)				\
+static inline bool soc_intel_is_##soc(void)			\
+{								\
+	static const struct x86_cpu_id soc##_cpu_ids[] = {	\
+		X86_MATCH_INTEL_FAM6_MODEL(type, NULL),		\
+		{}						\
+	};							\
+	const struct x86_cpu_id *id;				\
+								\
+	id = x86_match_cpu(soc##_cpu_ids);			\
+	if (id)							\
+		return true;					\
+	return false;						\
+}
+
+SOC_INTEL_IS_CPU(byt, ATOM_SILVERMONT);
+SOC_INTEL_IS_CPU(cht, ATOM_AIRMONT);
+SOC_INTEL_IS_CPU(apl, ATOM_GOLDMONT);
+SOC_INTEL_IS_CPU(glk, ATOM_GOLDMONT_PLUS);
+SOC_INTEL_IS_CPU(cml, KABYLAKE_L);
+
+#else /* IS_ENABLED(CONFIG_X86) */
+
+static inline bool soc_intel_is_byt(void)
+{
+	return false;
+}
+
+static inline bool soc_intel_is_cht(void)
+{
+	return false;
+}
+
+static inline bool soc_intel_is_apl(void)
+{
+	return false;
+}
+
+static inline bool soc_intel_is_glk(void)
+{
+	return false;
+}
+
+static inline bool soc_intel_is_cml(void)
+{
+	return false;
+}
+#endif /* IS_ENABLED(CONFIG_X86) */
+
+#endif /* __PLATFORM_DATA_X86_SOC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/platform_device.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/platform_device.h
@@ -31,7 +31,11 @@
 	struct resource	*resource;
 
 	const struct platform_device_id	*id_entry;
-	char *driver_override; /* Driver name to force a match */
+	/*
+	 * Driver name to force a match.  Do not set directly, because core
+	 * frees it.  Use driver_set_override() to set or clear it.
+	 */
+	const char *driver_override;
 
 	/* MFD cell pointer */
 	struct mfd_cell *mfd_cell;
@@ -203,7 +207,18 @@
 
 struct platform_driver {
 	int (*probe)(struct platform_device *);
+
+	/*
+	 * Traditionally the remove callback returned an int which however is
+	 * ignored by the driver core. This led to wrong expectations by driver
+	 * authors who thought returning an error code was a valid error
+	 * handling strategy. To convert to a callback returning void, new
+	 * drivers should implement .remove_new() until the conversion it done
+	 * that eventually makes .remove() return void.
+	 */
 	int (*remove)(struct platform_device *);
+	void (*remove_new)(struct platform_device *);
+
 	void (*shutdown)(struct platform_device *);
 	int (*suspend)(struct platform_device *, pm_message_t state);
 	int (*resume)(struct platform_device *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pm.h
@@ -8,6 +8,7 @@
 #ifndef _LINUX_PM_H
 #define _LINUX_PM_H
 
+#include <linux/export.h>
 #include <linux/list.h>
 #include <linux/workqueue.h>
 #include <linux/spinlock.h>
@@ -300,55 +301,101 @@
 	int (*runtime_idle)(struct device *dev);
 };
 
+#define SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
+	.suspend = pm_sleep_ptr(suspend_fn), \
+	.resume = pm_sleep_ptr(resume_fn), \
+	.freeze = pm_sleep_ptr(suspend_fn), \
+	.thaw = pm_sleep_ptr(resume_fn), \
+	.poweroff = pm_sleep_ptr(suspend_fn), \
+	.restore = pm_sleep_ptr(resume_fn),
+
+#define LATE_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
+	.suspend_late = pm_sleep_ptr(suspend_fn), \
+	.resume_early = pm_sleep_ptr(resume_fn), \
+	.freeze_late = pm_sleep_ptr(suspend_fn), \
+	.thaw_early = pm_sleep_ptr(resume_fn), \
+	.poweroff_late = pm_sleep_ptr(suspend_fn), \
+	.restore_early = pm_sleep_ptr(resume_fn),
+
+#define NOIRQ_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
+	.suspend_noirq = pm_sleep_ptr(suspend_fn), \
+	.resume_noirq = pm_sleep_ptr(resume_fn), \
+	.freeze_noirq = pm_sleep_ptr(suspend_fn), \
+	.thaw_noirq = pm_sleep_ptr(resume_fn), \
+	.poweroff_noirq = pm_sleep_ptr(suspend_fn), \
+	.restore_noirq = pm_sleep_ptr(resume_fn),
+
+#define RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn) \
+	.runtime_suspend = suspend_fn, \
+	.runtime_resume = resume_fn, \
+	.runtime_idle = idle_fn,
+
 #ifdef CONFIG_PM_SLEEP
 #define SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
-	.suspend = suspend_fn, \
-	.resume = resume_fn, \
-	.freeze = suspend_fn, \
-	.thaw = resume_fn, \
-	.poweroff = suspend_fn, \
-	.restore = resume_fn,
+	SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
 #else
 #define SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
 #endif
 
 #ifdef CONFIG_PM_SLEEP
 #define SET_LATE_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
-	.suspend_late = suspend_fn, \
-	.resume_early = resume_fn, \
-	.freeze_late = suspend_fn, \
-	.thaw_early = resume_fn, \
-	.poweroff_late = suspend_fn, \
-	.restore_early = resume_fn,
+	LATE_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
 #else
 #define SET_LATE_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
 #endif
 
 #ifdef CONFIG_PM_SLEEP
 #define SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
-	.suspend_noirq = suspend_fn, \
-	.resume_noirq = resume_fn, \
-	.freeze_noirq = suspend_fn, \
-	.thaw_noirq = resume_fn, \
-	.poweroff_noirq = suspend_fn, \
-	.restore_noirq = resume_fn,
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
 #else
 #define SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
 #endif
 
 #ifdef CONFIG_PM
 #define SET_RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn) \
-	.runtime_suspend = suspend_fn, \
-	.runtime_resume = resume_fn, \
-	.runtime_idle = idle_fn,
+	RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn)
 #else
 #define SET_RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn)
 #endif
 
+#define _DEFINE_DEV_PM_OPS(name, \
+			   suspend_fn, resume_fn, \
+			   runtime_suspend_fn, runtime_resume_fn, idle_fn) \
+const struct dev_pm_ops name = { \
+	SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
+	RUNTIME_PM_OPS(runtime_suspend_fn, runtime_resume_fn, idle_fn) \
+}
+
+#ifdef CONFIG_PM
+#define _EXPORT_DEV_PM_OPS(name, suspend_fn, resume_fn, runtime_suspend_fn, \
+			   runtime_resume_fn, idle_fn, sec) \
+	_DEFINE_DEV_PM_OPS(name, suspend_fn, resume_fn, runtime_suspend_fn, \
+			   runtime_resume_fn, idle_fn); \
+	_EXPORT_SYMBOL(name, sec)
+#else
+#define _EXPORT_DEV_PM_OPS(name, suspend_fn, resume_fn, runtime_suspend_fn, \
+			   runtime_resume_fn, idle_fn, sec) \
+static __maybe_unused _DEFINE_DEV_PM_OPS(__static_##name, suspend_fn, \
+					 resume_fn, runtime_suspend_fn, \
+					 runtime_resume_fn, idle_fn)
+#endif
+
 /*
  * Use this if you want to use the same suspend and resume callbacks for suspend
  * to RAM and hibernation.
+ *
+ * If the underlying dev_pm_ops struct symbol has to be exported, use
+ * EXPORT_SIMPLE_DEV_PM_OPS() or EXPORT_GPL_SIMPLE_DEV_PM_OPS() instead.
  */
+#define DEFINE_SIMPLE_DEV_PM_OPS(name, suspend_fn, resume_fn) \
+	_DEFINE_DEV_PM_OPS(name, suspend_fn, resume_fn, NULL, NULL, NULL)
+
+#define EXPORT_SIMPLE_DEV_PM_OPS(name, suspend_fn, resume_fn) \
+	_EXPORT_DEV_PM_OPS(name, suspend_fn, resume_fn, NULL, NULL, NULL, "")
+#define EXPORT_GPL_SIMPLE_DEV_PM_OPS(name, suspend_fn, resume_fn) \
+	_EXPORT_DEV_PM_OPS(name, suspend_fn, resume_fn, NULL, NULL, NULL, "_gpl")
+
+/* Deprecated. Use DEFINE_SIMPLE_DEV_PM_OPS() instead. */
 #define SIMPLE_DEV_PM_OPS(name, suspend_fn, resume_fn) \
 const struct dev_pm_ops __maybe_unused name = { \
 	SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) \
@@ -366,6 +413,9 @@
  * suspend and "early" resume callback pointers, .suspend_late() and
  * .resume_early(), to the same routines as .runtime_suspend() and
  * .runtime_resume(), respectively (and analogously for hibernation).
+ *
+ * Deprecated. You most likely don't want this macro. Use
+ * DEFINE_RUNTIME_DEV_PM_OPS() instead.
  */
 #define UNIVERSAL_DEV_PM_OPS(name, suspend_fn, resume_fn, idle_fn) \
 const struct dev_pm_ops __maybe_unused name = { \
@@ -373,11 +423,8 @@
 	SET_RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn) \
 }
 
-#ifdef CONFIG_PM
-#define pm_ptr(_ptr) (_ptr)
-#else
-#define pm_ptr(_ptr) NULL
-#endif
+#define pm_ptr(_ptr) PTR_IF(IS_ENABLED(CONFIG_PM), (_ptr))
+#define pm_sleep_ptr(_ptr) PTR_IF(IS_ENABLED(CONFIG_PM_SLEEP), (_ptr))
 
 /*
  * PM_EVENT_ messages
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pm_runtime.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pm_runtime.h
@@ -22,6 +22,20 @@
 					    usage_count */
 #define RPM_AUTO		0x08	/* Use autosuspend_delay */
 
+/*
+ * Use this for defining a set of PM operations to be used in all situations
+ * (system suspend, hibernation or runtime PM).
+ *
+ * Note that the behaviour differs from the deprecated UNIVERSAL_DEV_PM_OPS()
+ * macro, which uses the provided callbacks for both runtime PM and system
+ * sleep, while DEFINE_RUNTIME_DEV_PM_OPS() uses pm_runtime_force_suspend()
+ * and pm_runtime_force_resume() for its system sleep callbacks.
+ */
+#define DEFINE_RUNTIME_DEV_PM_OPS(name, suspend_fn, resume_fn, idle_fn) \
+	_DEFINE_DEV_PM_OPS(name, pm_runtime_force_suspend, \
+			   pm_runtime_force_resume, suspend_fn, \
+			   resume_fn, idle_fn)
+
 #ifdef CONFIG_PM
 extern struct workqueue_struct *pm_wq;
 
@@ -32,6 +46,7 @@
 
 extern int pm_generic_runtime_suspend(struct device *dev);
 extern int pm_generic_runtime_resume(struct device *dev);
+extern bool pm_runtime_need_not_resume(struct device *dev);
 extern int pm_runtime_force_suspend(struct device *dev);
 extern int pm_runtime_force_resume(struct device *dev);
 
@@ -58,6 +73,7 @@
 extern void pm_runtime_put_suppliers(struct device *dev);
 extern void pm_runtime_new_link(struct device *dev);
 extern void pm_runtime_drop_link(struct device_link *link);
+extern void pm_runtime_release_supplier(struct device_link *link);
 
 extern int devm_pm_runtime_enable(struct device *dev);
 
@@ -129,7 +145,7 @@
  * pm_runtime_active - Check whether or not a device is runtime-active.
  * @dev: Target device.
  *
- * Return %true if runtime PM is enabled for @dev and its runtime PM status is
+ * Return %true if runtime PM is disabled for @dev or its runtime PM status is
  * %RPM_ACTIVE, or %false otherwise.
  *
  * Note that the return value of this function can only be trusted if it is
@@ -219,6 +235,7 @@
 
 static inline int pm_generic_runtime_suspend(struct device *dev) { return 0; }
 static inline int pm_generic_runtime_resume(struct device *dev) { return 0; }
+static inline bool pm_runtime_need_not_resume(struct device *dev) {return true; }
 static inline int pm_runtime_force_suspend(struct device *dev) { return 0; }
 static inline int pm_runtime_force_resume(struct device *dev) { return 0; }
 
@@ -283,6 +300,7 @@
 static inline void pm_runtime_put_suppliers(struct device *dev) {}
 static inline void pm_runtime_new_link(struct device *dev) {}
 static inline void pm_runtime_drop_link(struct device_link *link) {}
+static inline void pm_runtime_release_supplier(struct device_link *link) {}
 
 #endif /* !CONFIG_PM */
 
@@ -540,6 +558,10 @@
  * Allow the runtime PM autosuspend mechanism to be used for @dev whenever
  * requested (or "autosuspend" will be handled as direct runtime-suspend for
  * it).
+ *
+ * NOTE: It's important to undo this with pm_runtime_dont_use_autosuspend()
+ * at driver exit time unless your driver initially enabled pm_runtime
+ * with devm_pm_runtime_enable() (which handles it for you).
  */
 static inline void pm_runtime_use_autosuspend(struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pm_wakeirq.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pm_wakeirq.h
@@ -17,8 +17,8 @@
 #ifdef CONFIG_PM
 
 extern int dev_pm_set_wake_irq(struct device *dev, int irq);
-extern int dev_pm_set_dedicated_wake_irq(struct device *dev,
-					 int irq);
+extern int dev_pm_set_dedicated_wake_irq(struct device *dev, int irq);
+extern int dev_pm_set_dedicated_wake_irq_reverse(struct device *dev, int irq);
 extern void dev_pm_clear_wake_irq(struct device *dev);
 extern void dev_pm_enable_wake_irq(struct device *dev);
 extern void dev_pm_disable_wake_irq(struct device *dev);
@@ -34,6 +34,11 @@
 {
 	return 0;
 }
+
+static inline int dev_pm_set_dedicated_wake_irq_reverse(struct device *dev, int irq)
+{
+	return 0;
+}
 
 static inline void dev_pm_clear_wake_irq(struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/poll.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/poll.h
@@ -16,11 +16,7 @@
 extern struct ctl_table epoll_table[]; /* for sysctl */
 /* ~832 bytes of stack space used max in sys_select/sys_poll before allocating
    additional memory. */
-#ifdef __clang__
-#define MAX_STACK_ALLOC 768
-#else
 #define MAX_STACK_ALLOC 832
-#endif
 #define FRONTEND_STACK_ALLOC	256
 #define SELECT_STACK_ALLOC	FRONTEND_STACK_ALLOC
 #define POLL_STACK_ALLOC	FRONTEND_STACK_ALLOC
@@ -47,8 +43,16 @@
 
 static inline void poll_wait(struct file * filp, wait_queue_head_t * wait_address, poll_table *p)
 {
-	if (p && p->_qproc && wait_address)
+	if (p && p->_qproc && wait_address) {
 		p->_qproc(filp, wait_address, p);
+		/*
+		 * This memory barrier is paired in the wq_has_sleeper().
+		 * See the comment above prepare_to_wait(), we need to
+		 * ensure that subsequent tests in this thread can't be
+		 * reordered with __add_wait_queue() in _qproc() paths.
+		 */
+		smp_mb();
+	}
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/posix-timers.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/posix-timers.h
@@ -4,6 +4,7 @@
 
 #include <linux/spinlock.h>
 #include <linux/list.h>
+#include <linux/mutex.h>
 #include <linux/alarmtimer.h>
 #include <linux/timerqueue.h>
 #include <linux/task_work.h>
@@ -63,16 +64,18 @@
  * cpu_timer - Posix CPU timer representation for k_itimer
  * @node:	timerqueue node to queue in the task/sig
  * @head:	timerqueue head on which this timer is queued
- * @task:	Pointer to target task
+ * @pid:	Pointer to target task PID
  * @elist:	List head for the expiry list
  * @firing:	Timer is currently firing
+ * @handling:	Pointer to the task which handles expiry
  */
 struct cpu_timer {
-	struct timerqueue_node	node;
-	struct timerqueue_head	*head;
-	struct pid		*pid;
-	struct list_head	elist;
-	int			firing;
+	struct timerqueue_node		node;
+	struct timerqueue_head		*head;
+	struct pid			*pid;
+	struct list_head		elist;
+	int				firing;
+	struct task_struct __rcu	*handling;
 };
 
 static inline bool cpu_timer_enqueue(struct timerqueue_head *head,
@@ -136,10 +139,12 @@
 /**
  * posix_cputimers_work - Container for task work based posix CPU timer expiry
  * @work:	The task work to be scheduled
+ * @mutex:	Mutex held around expiry in context of this task work
  * @scheduled:  @work has been scheduled already, no further processing
  */
 struct posix_cputimers_work {
 	struct callback_head	work;
+	struct mutex		mutex;
 	unsigned int		scheduled;
 };
 
@@ -184,8 +189,10 @@
 #endif
 
 #ifdef CONFIG_POSIX_CPU_TIMERS_TASK_WORK
+void clear_posix_cputimers_work(struct task_struct *p);
 void posix_cputimers_init_work(void);
 #else
+static inline void clear_posix_cputimers_work(struct task_struct *p) { }
 static inline void posix_cputimers_init_work(void) { }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/posix_acl_xattr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/posix_acl_xattr.h
@@ -34,15 +34,19 @@
 
 #ifdef CONFIG_FS_POSIX_ACL
 void posix_acl_fix_xattr_from_user(struct user_namespace *mnt_userns,
+				   struct inode *inode,
 				   void *value, size_t size);
 void posix_acl_fix_xattr_to_user(struct user_namespace *mnt_userns,
+				   struct inode *inode,
 				 void *value, size_t size);
 #else
 static inline void posix_acl_fix_xattr_from_user(struct user_namespace *mnt_userns,
+						 struct inode *inode,
 						 void *value, size_t size)
 {
 }
 static inline void posix_acl_fix_xattr_to_user(struct user_namespace *mnt_userns,
+					       struct inode *inode,
 					       void *value, size_t size)
 {
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/power/bq27xxx_battery.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/power/bq27xxx_battery.h
@@ -2,6 +2,8 @@
 #ifndef __LINUX_BQ27X00_BATTERY_H__
 #define __LINUX_BQ27X00_BATTERY_H__
 
+#include <linux/power_supply.h>
+
 enum bq27xxx_chip {
 	BQ27000 = 1, /* bq27000, bq27200 */
 	BQ27010, /* bq27010, bq27210 */
@@ -68,7 +70,9 @@
 	struct bq27xxx_access_methods bus;
 	struct bq27xxx_reg_cache cache;
 	int charge_design_full;
+	bool removed;
 	unsigned long last_update;
+	union power_supply_propval last_status;
 	struct delayed_work work;
 	struct power_supply *bat;
 	struct list_head list;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/power_supply.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/power_supply.h
@@ -420,8 +420,9 @@
 				int table_len, int temp);
 extern void power_supply_changed(struct power_supply *psy);
 extern int power_supply_am_i_supplied(struct power_supply *psy);
-extern int power_supply_set_input_current_limit_from_supplier(
-					 struct power_supply *psy);
+int power_supply_get_property_from_supplier(struct power_supply *psy,
+					    enum power_supply_property psp,
+					    union power_supply_propval *val);
 extern int power_supply_set_battery_charged(struct power_supply *psy);
 
 #ifdef CONFIG_POWER_SUPPLY
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pps_kernel.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pps_kernel.h
@@ -56,8 +56,7 @@
 
 	unsigned int id;			/* PPS source unique ID */
 	void const *lookup_cookie;		/* For pps_lookup_dev() only */
-	struct cdev cdev;
-	struct device *dev;
+	struct device dev;
 	struct fasync_struct *async_queue;	/* fasync method */
 	spinlock_t lock;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/prandom.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/prandom.h
@@ -10,6 +10,7 @@
 
 #include <linux/types.h>
 #include <linux/percpu.h>
+#include <linux/siphash.h>
 
 u32 prandom_u32(void);
 void prandom_bytes(void *buf, size_t nbytes);
@@ -27,15 +28,10 @@
  * The core SipHash round function.  Each line can be executed in
  * parallel given enough CPU resources.
  */
-#define PRND_SIPROUND(v0, v1, v2, v3) ( \
-	v0 += v1, v1 = rol64(v1, 13),  v2 += v3, v3 = rol64(v3, 16), \
-	v1 ^= v0, v0 = rol64(v0, 32),  v3 ^= v2,                     \
-	v0 += v3, v3 = rol64(v3, 21),  v2 += v1, v1 = rol64(v1, 17), \
-	v3 ^= v0,                      v1 ^= v2, v2 = rol64(v2, 32)  \
-)
+#define PRND_SIPROUND(v0, v1, v2, v3) SIPHASH_PERMUTATION(v0, v1, v2, v3)
 
-#define PRND_K0 (0x736f6d6570736575 ^ 0x6c7967656e657261)
-#define PRND_K1 (0x646f72616e646f6d ^ 0x7465646279746573)
+#define PRND_K0 (SIPHASH_CONST_0 ^ SIPHASH_CONST_2)
+#define PRND_K1 (SIPHASH_CONST_1 ^ SIPHASH_CONST_3)
 
 #elif BITS_PER_LONG == 32
 /*
@@ -43,14 +39,9 @@
  * This is weaker, but 32-bit machines are not used for high-traffic
  * applications, so there is less output for an attacker to analyze.
  */
-#define PRND_SIPROUND(v0, v1, v2, v3) ( \
-	v0 += v1, v1 = rol32(v1,  5),  v2 += v3, v3 = rol32(v3,  8), \
-	v1 ^= v0, v0 = rol32(v0, 16),  v3 ^= v2,                     \
-	v0 += v3, v3 = rol32(v3,  7),  v2 += v1, v1 = rol32(v1, 13), \
-	v3 ^= v0,                      v1 ^= v2, v2 = rol32(v2, 16)  \
-)
-#define PRND_K0 0x6c796765
-#define PRND_K1 0x74656462
+#define PRND_SIPROUND(v0, v1, v2, v3) HSIPHASH_PERMUTATION(v0, v1, v2, v3)
+#define PRND_K0 (HSIPHASH_CONST_0 ^ HSIPHASH_CONST_2)
+#define PRND_K1 (HSIPHASH_CONST_1 ^ HSIPHASH_CONST_3)
 
 #else
 #error Unsupported BITS_PER_LONG
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/preempt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/preempt.h
@@ -77,14 +77,42 @@
 /* preempt_count() and related functions, depends on PREEMPT_NEED_RESCHED */
 #include <asm/preempt.h>
 
+/**
+ * interrupt_context_level - return interrupt context level
+ *
+ * Returns the current interrupt context level.
+ *  0 - normal context
+ *  1 - softirq context
+ *  2 - hardirq context
+ *  3 - NMI context
+ */
+static __always_inline unsigned char interrupt_context_level(void)
+{
+	unsigned long pc = preempt_count();
+	unsigned char level = 0;
+
+	level += !!(pc & (NMI_MASK));
+	level += !!(pc & (NMI_MASK | HARDIRQ_MASK));
+	level += !!(pc & (NMI_MASK | HARDIRQ_MASK | SOFTIRQ_OFFSET));
+
+	return level;
+}
+
+/*
+ * These macro definitions avoid redundant invocations of preempt_count()
+ * because such invocations would result in redundant loads given that
+ * preempt_count() is commonly implemented with READ_ONCE().
+ */
+
 #define nmi_count()	(preempt_count() & NMI_MASK)
 #define hardirq_count()	(preempt_count() & HARDIRQ_MASK)
 #ifdef CONFIG_PREEMPT_RT
 # define softirq_count()	(current->softirq_disable_cnt & SOFTIRQ_MASK)
+# define irq_count()		((preempt_count() & (NMI_MASK | HARDIRQ_MASK)) | softirq_count())
 #else
 # define softirq_count()	(preempt_count() & SOFTIRQ_MASK)
+# define irq_count()		(preempt_count() & (NMI_MASK | HARDIRQ_MASK | SOFTIRQ_MASK))
 #endif
-#define irq_count()	(nmi_count() | hardirq_count() | softirq_count())
 
 /*
  * Macros to retrieve the current execution context:
@@ -97,7 +125,11 @@
 #define in_nmi()		(nmi_count())
 #define in_hardirq()		(hardirq_count())
 #define in_serving_softirq()	(softirq_count() & SOFTIRQ_OFFSET)
-#define in_task()		(!(in_nmi() | in_hardirq() | in_serving_softirq()))
+#ifdef CONFIG_PREEMPT_RT
+# define in_task()		(!((preempt_count() & (NMI_MASK | HARDIRQ_MASK)) | in_serving_softirq()))
+#else
+# define in_task()		(!(preempt_count() & (NMI_MASK | HARDIRQ_MASK | SOFTIRQ_OFFSET)))
+#endif
 
 /*
  * The following macros are deprecated and should not be used in new code:
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/printk.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/printk.h
@@ -129,7 +129,7 @@
 #define no_printk(fmt, ...)				\
 ({							\
 	if (0)						\
-		printk(fmt, ##__VA_ARGS__);		\
+		_printk(fmt, ##__VA_ARGS__);		\
 	0;						\
 })
 
@@ -198,6 +198,7 @@
 void show_regs_print_info(const char *log_lvl);
 extern asmlinkage void dump_stack_lvl(const char *log_lvl) __cold;
 extern asmlinkage void dump_stack(void) __cold;
+void printk_trigger_flush(void);
 #else
 static inline __printf(1, 0)
 int vprintk(const char *s, va_list args)
@@ -274,6 +275,9 @@
 static inline void dump_stack(void)
 {
 }
+static inline void printk_trigger_flush(void)
+{
+}
 #endif
 
 #ifdef CONFIG_SMP
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/proc_fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/proc_fs.h
@@ -20,10 +20,13 @@
 	 * If in doubt, ignore this flag.
 	 */
 #ifdef MODULE
-	PROC_ENTRY_PERMANENT = 0U,
+	PROC_ENTRY_PERMANENT		= 0U,
 #else
-	PROC_ENTRY_PERMANENT = 1U << 0,
+	PROC_ENTRY_PERMANENT		= 1U << 0,
 #endif
+
+	PROC_ENTRY_proc_read_iter	= 1U << 1,
+	PROC_ENTRY_proc_compat_ioctl	= 1U << 2,
 };
 
 struct proc_ops {
@@ -191,8 +194,10 @@
 static inline int remove_proc_subtree(const char *name, struct proc_dir_entry *parent) { return 0; }
 
 #define proc_create_net_data(name, mode, parent, ops, state_size, data) ({NULL;})
+#define proc_create_net_data_write(name, mode, parent, ops, write, state_size, data) ({NULL;})
 #define proc_create_net(name, mode, parent, state_size, ops) ({NULL;})
 #define proc_create_net_single(name, mode, parent, show, data) ({NULL;})
+#define proc_create_net_single_write(name, mode, parent, show, write, data) ({NULL;})
 
 static inline struct pid *tgid_pidfd_to_pid(const struct file *file)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/profile.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/profile.h
@@ -11,7 +11,6 @@
 
 #define CPU_PROFILING	1
 #define SCHED_PROFILING	2
-#define SLEEP_PROFILING	3
 #define KVM_PROFILING	4
 
 struct proc_dir_entry;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/property.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/property.h
@@ -31,7 +31,12 @@
 	DEV_DMA_COHERENT,
 };
 
-struct fwnode_handle *dev_fwnode(struct device *dev);
+const struct fwnode_handle *__dev_fwnode_const(const struct device *dev);
+struct fwnode_handle *__dev_fwnode(struct device *dev);
+#define dev_fwnode(dev)							\
+	_Generic((dev),							\
+		 const struct device *: __dev_fwnode_const,	\
+		 struct device *: __dev_fwnode)(dev)
 
 bool device_property_present(struct device *dev, const char *propname);
 int device_property_read_u8_array(struct device *dev, const char *propname,
@@ -120,6 +125,9 @@
 void fwnode_handle_put(struct fwnode_handle *fwnode);
 
 int fwnode_irq_get(const struct fwnode_handle *fwnode, unsigned int index);
+int fwnode_irq_get_byname(const struct fwnode_handle *fwnode, const char *name);
+
+void __iomem *fwnode_iomap(struct fwnode_handle *fwnode, int index);
 
 unsigned int device_get_child_node_count(struct device *dev);
 
@@ -385,7 +393,7 @@
 
 enum dev_dma_attr device_get_dma_attr(struct device *dev);
 
-const void *device_get_match_data(struct device *dev);
+const void *device_get_match_data(const struct device *dev);
 
 int device_get_phy_mode(struct device *dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/psi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/psi.h
@@ -24,18 +24,17 @@
 void psi_memstall_leave(unsigned long *flags);
 
 int psi_show(struct seq_file *s, struct psi_group *group, enum psi_res res);
-
-#ifdef CONFIG_CGROUPS
-int psi_cgroup_alloc(struct cgroup *cgrp);
-void psi_cgroup_free(struct cgroup *cgrp);
-void cgroup_move_task(struct task_struct *p, struct css_set *to);
-
 struct psi_trigger *psi_trigger_create(struct psi_group *group,
 			char *buf, size_t nbytes, enum psi_res res);
-void psi_trigger_replace(void **trigger_ptr, struct psi_trigger *t);
+void psi_trigger_destroy(struct psi_trigger *t);
 
 __poll_t psi_trigger_poll(void **trigger_ptr, struct file *file,
 			poll_table *wait);
+
+#ifdef CONFIG_CGROUPS
+int psi_cgroup_alloc(struct cgroup *cgrp);
+void psi_cgroup_free(struct cgroup *cgrp);
+void cgroup_move_task(struct task_struct *p, struct css_set *to);
 #endif
 
 #else /* CONFIG_PSI */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/psi_types.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/psi_types.h
@@ -21,7 +21,17 @@
 	 * don't have to special case any state tracking for it.
 	 */
 	NR_ONCPU,
-	NR_PSI_TASK_COUNTS = 4,
+	/*
+	 * For IO and CPU stalls the presence of running/oncpu tasks
+	 * in the domain means a partial rather than a full stall.
+	 * For memory it's not so simple because of page reclaimers:
+	 * they are running/oncpu while representing a stall. To tell
+	 * whether a domain has productivity left or not, we need to
+	 * distinguish between regular running (i.e. productive)
+	 * threads and memstall ones.
+	 */
+	NR_MEMSTALL_RUNNING,
+	NR_PSI_TASK_COUNTS = 5,
 };
 
 /* Task state bitmasks */
@@ -29,6 +39,7 @@
 #define TSK_MEMSTALL	(1 << NR_MEMSTALL)
 #define TSK_RUNNING	(1 << NR_RUNNING)
 #define TSK_ONCPU	(1 << NR_ONCPU)
+#define TSK_MEMSTALL_RUNNING	(1 << NR_MEMSTALL_RUNNING)
 
 /* Resources that workloads could be stalled on */
 enum psi_res {
@@ -129,9 +140,6 @@
 	 * events to one per window
 	 */
 	u64 last_event_time;
-
-	/* Refcounting to prevent premature destruction */
-	struct kref refcount;
 };
 
 struct psi_group {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pstore.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pstore.h
@@ -14,7 +14,7 @@
 #include <linux/errno.h>
 #include <linux/kmsg_dump.h>
 #include <linux/mutex.h>
-#include <linux/semaphore.h>
+#include <linux/spinlock.h>
 #include <linux/time.h>
 #include <linux/types.h>
 
@@ -87,7 +87,7 @@
  * @owner:	module which is responsible for this backend driver
  * @name:	name of the backend driver
  *
- * @buf_lock:	semaphore to serialize access to @buf
+ * @buf_lock:	spinlock to serialize access to @buf
  * @buf:	preallocated crash dump buffer
  * @bufsize:	size of @buf available for crash dump bytes (must match
  *		smallest number of bytes available for writing to a
@@ -178,7 +178,7 @@
 	struct module	*owner;
 	const char	*name;
 
-	struct semaphore buf_lock;
+	spinlock_t	buf_lock;
 	char		*buf;
 	size_t		bufsize;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ptp_classify.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ptp_classify.h
@@ -42,6 +42,9 @@
 #define OFF_PTP_SOURCE_UUID	22 /* PTPv1 only */
 #define OFF_PTP_SEQUENCE_ID	30
 
+/* PTP header flag fields */
+#define PTP_FLAG_TWOSTEP	BIT(1)
+
 /* Below defines should actually be removed at some point in time. */
 #define IP6_HLEN	40
 #define UDP_HLEN	8
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ptp_clock_kernel.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ptp_clock_kernel.h
@@ -351,15 +351,17 @@
  *
  * @hwtstamps:    skb_shared_hwtstamps structure pointer
  * @vclock_index: phc index of ptp vclock.
+ *
+ * Returns converted timestamp, or 0 on error.
  */
-void ptp_convert_timestamp(struct skb_shared_hwtstamps *hwtstamps,
-			   int vclock_index);
+ktime_t ptp_convert_timestamp(const struct skb_shared_hwtstamps *hwtstamps,
+			      int vclock_index);
 #else
 static inline int ptp_get_vclocks_index(int pclock_index, int **vclock_index)
 { return 0; }
-static inline void ptp_convert_timestamp(struct skb_shared_hwtstamps *hwtstamps,
-					 int vclock_index)
-{ }
+static inline ktime_t ptp_convert_timestamp(const struct skb_shared_hwtstamps *hwtstamps,
+					    int vclock_index)
+{ return 0; }
 
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ptp_kvm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ptp_kvm.h
@@ -12,6 +12,7 @@
 struct clocksource;
 
 int kvm_arch_ptp_init(void);
+void kvm_arch_ptp_exit(void);
 int kvm_arch_ptp_get_clock(struct timespec64 *ts);
 int kvm_arch_ptp_get_crosststamp(u64 *cycle,
 		struct timespec64 *tspec, struct clocksource **cs);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ptrace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ptrace.h
@@ -30,7 +30,6 @@
 
 #define PT_SEIZED	0x00010000	/* SEIZE used, enable new behavior */
 #define PT_PTRACED	0x00000001
-#define PT_DTRACE	0x00000002	/* delayed trace (used on m68k, i386) */
 
 #define PT_OPT_FLAG_SHIFT	3
 /* PT_TRACE_* event enable flags */
@@ -47,12 +46,6 @@
 #define PT_EXITKILL		(PTRACE_O_EXITKILL << PT_OPT_FLAG_SHIFT)
 #define PT_SUSPEND_SECCOMP	(PTRACE_O_SUSPEND_SECCOMP << PT_OPT_FLAG_SHIFT)
 
-/* single stepping state bits (used on ARM and PA-RISC) */
-#define PT_SINGLESTEP_BIT	31
-#define PT_SINGLESTEP		(1<<PT_SINGLESTEP_BIT)
-#define PT_BLOCKSTEP_BIT	30
-#define PT_BLOCKSTEP		(1<<PT_BLOCKSTEP_BIT)
-
 extern long arch_ptrace(struct task_struct *child, long request,
 			unsigned long addr, unsigned long data);
 extern int ptrace_readdata(struct task_struct *tsk, unsigned long src, char __user *dst, int len);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/pwm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/pwm.h
@@ -44,8 +44,8 @@
 };
 
 enum {
-	PWMF_REQUESTED = 1 << 0,
-	PWMF_EXPORTED = 1 << 1,
+	PWMF_REQUESTED = 0,
+	PWMF_EXPORTED = 1,
 };
 
 /*
@@ -488,6 +488,11 @@
 {
 	return -EINVAL;
 }
+
+static inline int devm_pwmchip_add(struct device *dev, struct pwm_chip *chip)
+{
+	return -EINVAL;
+}
 
 static inline struct pwm_device *pwm_request_from_chip(struct pwm_chip *chip,
 						       unsigned int index,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_chain.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_chain.h
@@ -268,14 +268,15 @@
 }
 
 /**
- * @brief qed_chain_advance_page -
+ * qed_chain_advance_page(): Advance the next element across pages for a
+ *                           linked chain.
  *
- * Advance the next element across pages for a linked chain
+ * @p_chain: P_chain.
+ * @p_next_elem: P_next_elem.
+ * @idx_to_inc: Idx_to_inc.
+ * @page_to_inc: page_to_inc.
  *
- * @param p_chain
- * @param p_next_elem
- * @param idx_to_inc
- * @param page_to_inc
+ * Return: Void.
  */
 static inline void
 qed_chain_advance_page(struct qed_chain *p_chain,
@@ -336,12 +337,14 @@
 	} while (0)
 
 /**
- * @brief qed_chain_return_produced -
+ * qed_chain_return_produced(): A chain in which the driver "Produces"
+ *                              elements should use this API
+ *                              to indicate previous produced elements
+ *                              are now consumed.
  *
- * A chain in which the driver "Produces" elements should use this API
- * to indicate previous produced elements are now consumed.
+ * @p_chain: Chain.
  *
- * @param p_chain
+ * Return: Void.
  */
 static inline void qed_chain_return_produced(struct qed_chain *p_chain)
 {
@@ -353,15 +356,15 @@
 }
 
 /**
- * @brief qed_chain_produce -
+ * qed_chain_produce(): A chain in which the driver "Produces"
+ *                      elements should use this to get a pointer to
+ *                      the next element which can be "Produced". It's driver
+ *                      responsibility to validate that the chain has room for
+ *                      new element.
  *
- * A chain in which the driver "Produces" elements should use this to get
- * a pointer to the next element which can be "Produced". It's driver
- * responsibility to validate that the chain has room for new element.
+ * @p_chain: Chain.
  *
- * @param p_chain
- *
- * @return void*, a pointer to next element
+ * Return: void*, a pointer to next element.
  */
 static inline void *qed_chain_produce(struct qed_chain *p_chain)
 {
@@ -395,14 +398,11 @@
 }
 
 /**
- * @brief qed_chain_get_capacity -
- *
- * Get the maximum number of BDs in chain
+ * qed_chain_get_capacity(): Get the maximum number of BDs in chain
  *
- * @param p_chain
- * @param num
+ * @p_chain: Chain.
  *
- * @return number of unusable BDs
+ * Return: number of unusable BDs.
  */
 static inline u32 qed_chain_get_capacity(struct qed_chain *p_chain)
 {
@@ -410,12 +410,14 @@
 }
 
 /**
- * @brief qed_chain_recycle_consumed -
+ * qed_chain_recycle_consumed(): Returns an element which was
+ *                               previously consumed;
+ *                               Increments producers so they could
+ *                               be written to FW.
  *
- * Returns an element which was previously consumed;
- * Increments producers so they could be written to FW.
+ * @p_chain: Chain.
  *
- * @param p_chain
+ * Return: Void.
  */
 static inline void qed_chain_recycle_consumed(struct qed_chain *p_chain)
 {
@@ -427,14 +429,13 @@
 }
 
 /**
- * @brief qed_chain_consume -
+ * qed_chain_consume(): A Chain in which the driver utilizes data written
+ *                      by a different source (i.e., FW) should use this to
+ *                      access passed buffers.
  *
- * A Chain in which the driver utilizes data written by a different source
- * (i.e., FW) should use this to access passed buffers.
+ * @p_chain: Chain.
  *
- * @param p_chain
- *
- * @return void*, a pointer to the next buffer written
+ * Return: void*, a pointer to the next buffer written.
  */
 static inline void *qed_chain_consume(struct qed_chain *p_chain)
 {
@@ -468,9 +469,11 @@
 }
 
 /**
- * @brief qed_chain_reset - Resets the chain to its start state
+ * qed_chain_reset(): Resets the chain to its start state.
+ *
+ * @p_chain: pointer to a previously allocated chain.
  *
- * @param p_chain pointer to a previously allocated chain
+ * Return Void.
  */
 static inline void qed_chain_reset(struct qed_chain *p_chain)
 {
@@ -519,13 +522,12 @@
 }
 
 /**
- * @brief qed_chain_get_last_elem -
+ * qed_chain_get_last_elem(): Returns a pointer to the last element of the
+ *                            chain.
  *
- * Returns a pointer to the last element of the chain
+ * @p_chain: Chain.
  *
- * @param p_chain
- *
- * @return void*
+ * Return: void*.
  */
 static inline void *qed_chain_get_last_elem(struct qed_chain *p_chain)
 {
@@ -563,10 +565,13 @@
 }
 
 /**
- * @brief qed_chain_set_prod - sets the prod to the given value
+ * qed_chain_set_prod(): sets the prod to the given value.
+ *
+ * @p_chain: Chain.
+ * @prod_idx: Prod Idx.
+ * @p_prod_elem: Prod elem.
  *
- * @param prod_idx
- * @param p_prod_elem
+ * Return Void.
  */
 static inline void qed_chain_set_prod(struct qed_chain *p_chain,
 				      u32 prod_idx, void *p_prod_elem)
@@ -610,9 +615,11 @@
 }
 
 /**
- * @brief qed_chain_pbl_zero_mem - set chain memory to 0
+ * qed_chain_pbl_zero_mem(): set chain memory to 0.
+ *
+ * @p_chain: Chain.
  *
- * @param p_chain
+ * Return: Void.
  */
 static inline void qed_chain_pbl_zero_mem(struct qed_chain *p_chain)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_eth_if.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_eth_if.h
@@ -145,12 +145,6 @@
 	unsigned char mac[64][ETH_ALEN];
 };
 
-union qed_filter_type_params {
-	enum qed_filter_rx_mode_type accept_flags;
-	struct qed_filter_ucast_params ucast;
-	struct qed_filter_mcast_params mcast;
-};
-
 enum qed_filter_type {
 	QED_FILTER_TYPE_UCAST,
 	QED_FILTER_TYPE_MCAST,
@@ -158,11 +152,6 @@
 	QED_MAX_FILTER_TYPES,
 };
 
-struct qed_filter_params {
-	enum qed_filter_type type;
-	union qed_filter_type_params filter;
-};
-
 struct qed_tunn_params {
 	u16 vxlan_port;
 	u8 update_vxlan_port;
@@ -314,8 +303,14 @@
 
 	int (*q_tx_stop)(struct qed_dev *cdev, u8 rss_id, void *handle);
 
-	int (*filter_config)(struct qed_dev *cdev,
-			     struct qed_filter_params *params);
+	int (*filter_config_rx_mode)(struct qed_dev *cdev,
+				     enum qed_filter_rx_mode_type type);
+
+	int (*filter_config_ucast)(struct qed_dev *cdev,
+				   struct qed_filter_ucast_params *params);
+
+	int (*filter_config_mcast)(struct qed_dev *cdev,
+				   struct qed_filter_mcast_params *params);
 
 	int (*fastpath_stop)(struct qed_dev *cdev);
 
@@ -336,7 +331,7 @@
 	int (*configure_arfs_searcher)(struct qed_dev *cdev,
 				       enum qed_filter_config_mode mode);
 	int (*get_coalesce)(struct qed_dev *cdev, u16 *coal, void *handle);
-	int (*req_bulletin_update_mac)(struct qed_dev *cdev, u8 *mac);
+	int (*req_bulletin_update_mac)(struct qed_dev *cdev, const u8 *mac);
 };
 
 const struct qed_eth_ops *qed_get_eth_ops(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_if.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_if.h
@@ -819,47 +819,47 @@
 
 struct qed_selftest_ops {
 /**
- * @brief selftest_interrupt - Perform interrupt test
+ * selftest_interrupt(): Perform interrupt test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*selftest_interrupt)(struct qed_dev *cdev);
 
 /**
- * @brief selftest_memory - Perform memory test
+ * selftest_memory(): Perform memory test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*selftest_memory)(struct qed_dev *cdev);
 
 /**
- * @brief selftest_register - Perform register test
+ * selftest_register(): Perform register test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*selftest_register)(struct qed_dev *cdev);
 
 /**
- * @brief selftest_clock - Perform clock test
+ * selftest_clock(): Perform clock test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*selftest_clock)(struct qed_dev *cdev);
 
 /**
- * @brief selftest_nvram - Perform nvram test
+ * selftest_nvram(): Perform nvram test.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*selftest_nvram) (struct qed_dev *cdev);
 };
@@ -927,47 +927,53 @@
 				  enum qed_hw_err_type err_type);
 
 /**
- * @brief can_link_change - can the instance change the link or not
+ * can_link_change(): can the instance change the link or not.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return true if link-change is allowed, false otherwise.
+ * Return: true if link-change is allowed, false otherwise.
  */
 	bool (*can_link_change)(struct qed_dev *cdev);
 
 /**
- * @brief set_link - set links according to params
+ * set_link(): set links according to params.
  *
- * @param cdev
- * @param params - values used to override the default link configuration
+ * @cdev: Qed dev pointer.
+ * @params: values used to override the default link configuration.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int		(*set_link)(struct qed_dev *cdev,
 				    struct qed_link_params *params);
 
 /**
- * @brief get_link - returns the current link state.
+ * get_link(): returns the current link state.
  *
- * @param cdev
- * @param if_link - structure to be filled with current link configuration.
+ * @cdev: Qed dev pointer.
+ * @if_link: structure to be filled with current link configuration.
+ *
+ * Return: Void.
  */
 	void		(*get_link)(struct qed_dev *cdev,
 				    struct qed_link_output *if_link);
 
 /**
- * @brief - drains chip in case Tx completions fail to arrive due to pause.
+ * drain(): drains chip in case Tx completions fail to arrive due to pause.
+ *
+ * @cdev: Qed dev pointer.
  *
- * @param cdev
+ * Return: Int.
  */
 	int		(*drain)(struct qed_dev *cdev);
 
 /**
- * @brief update_msglvl - update module debug level
+ * update_msglvl(): update module debug level.
  *
- * @param cdev
- * @param dp_module
- * @param dp_level
+ * @cdev: Qed dev pointer.
+ * @dp_module: Debug module.
+ * @dp_level: Debug level.
+ *
+ * Return: Void.
  */
 	void		(*update_msglvl)(struct qed_dev *cdev,
 					 u32 dp_module,
@@ -981,70 +987,73 @@
 				      struct qed_chain *p_chain);
 
 /**
- * @brief nvm_flash - Flash nvm data.
+ * nvm_flash(): Flash nvm data.
  *
- * @param cdev
- * @param name - file containing the data
+ * @cdev: Qed dev pointer.
+ * @name: file containing the data.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*nvm_flash)(struct qed_dev *cdev, const char *name);
 
 /**
- * @brief nvm_get_image - reads an entire image from nvram
+ * nvm_get_image(): reads an entire image from nvram.
  *
- * @param cdev
- * @param type - type of the request nvram image
- * @param buf - preallocated buffer to fill with the image
- * @param len - length of the allocated buffer
+ * @cdev: Qed dev pointer.
+ * @type: type of the request nvram image.
+ * @buf: preallocated buffer to fill with the image.
+ * @len: length of the allocated buffer.
  *
- * @return 0 on success, error otherwise
+ * Return: 0 on success, error otherwise.
  */
 	int (*nvm_get_image)(struct qed_dev *cdev,
 			     enum qed_nvm_images type, u8 *buf, u16 len);
 
 /**
- * @brief set_coalesce - Configure Rx coalesce value in usec
+ * set_coalesce(): Configure Rx coalesce value in usec.
  *
- * @param cdev
- * @param rx_coal - Rx coalesce value in usec
- * @param tx_coal - Tx coalesce value in usec
- * @param qid - Queue index
- * @param sb_id - Status Block Id
+ * @cdev: Qed dev pointer.
+ * @rx_coal: Rx coalesce value in usec.
+ * @tx_coal: Tx coalesce value in usec.
+ * @handle: Handle.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*set_coalesce)(struct qed_dev *cdev,
 			    u16 rx_coal, u16 tx_coal, void *handle);
 
 /**
- * @brief set_led - Configure LED mode
+ * set_led() - Configure LED mode.
  *
- * @param cdev
- * @param mode - LED mode
+ * @cdev: Qed dev pointer.
+ * @mode: LED mode.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*set_led)(struct qed_dev *cdev,
 		       enum qed_led_mode mode);
 
 /**
- * @brief attn_clr_enable - Prevent attentions from being reasserted
+ * attn_clr_enable(): Prevent attentions from being reasserted.
+ *
+ * @cdev: Qed dev pointer.
+ * @clr_enable: Clear enable.
  *
- * @param cdev
- * @param clr_enable
+ * Return: Void.
  */
 	void (*attn_clr_enable)(struct qed_dev *cdev, bool clr_enable);
 
 /**
- * @brief db_recovery_add - add doorbell information to the doorbell
- * recovery mechanism.
+ * db_recovery_add(): add doorbell information to the doorbell
+ *                    recovery mechanism.
  *
- * @param cdev
- * @param db_addr - doorbell address
- * @param db_data - address of where db_data is stored
- * @param db_is_32b - doorbell is 32b pr 64b
- * @param db_is_user - doorbell recovery addresses are user or kernel space
+ * @cdev: Qed dev pointer.
+ * @db_addr: Doorbell address.
+ * @db_data: Dddress of where db_data is stored.
+ * @db_width: Doorbell is 32b or 64b.
+ * @db_space: Doorbell recovery addresses are user or kernel space.
+ *
+ * Return: Int.
  */
 	int (*db_recovery_add)(struct qed_dev *cdev,
 			       void __iomem *db_addr,
@@ -1053,114 +1062,130 @@
 			       enum qed_db_rec_space db_space);
 
 /**
- * @brief db_recovery_del - remove doorbell information from the doorbell
+ * db_recovery_del(): remove doorbell information from the doorbell
  * recovery mechanism. db_data serves as key (db_addr is not unique).
  *
- * @param cdev
- * @param db_addr - doorbell address
- * @param db_data - address where db_data is stored. Serves as key for the
- *		    entry to delete.
+ * @cdev: Qed dev pointer.
+ * @db_addr: Doorbell address.
+ * @db_data: Address where db_data is stored. Serves as key for the
+ *           entry to delete.
+ *
+ * Return: Int.
  */
 	int (*db_recovery_del)(struct qed_dev *cdev,
 			       void __iomem *db_addr, void *db_data);
 
 /**
- * @brief recovery_process - Trigger a recovery process
+ * recovery_process(): Trigger a recovery process.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*recovery_process)(struct qed_dev *cdev);
 
 /**
- * @brief recovery_prolog - Execute the prolog operations of a recovery process
+ * recovery_prolog(): Execute the prolog operations of a recovery process.
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*recovery_prolog)(struct qed_dev *cdev);
 
 /**
- * @brief update_drv_state - API to inform the change in the driver state.
+ * update_drv_state(): API to inform the change in the driver state.
  *
- * @param cdev
- * @param active
+ * @cdev: Qed dev pointer.
+ * @active: Active
  *
+ * Return: Int.
  */
 	int (*update_drv_state)(struct qed_dev *cdev, bool active);
 
 /**
- * @brief update_mac - API to inform the change in the mac address
+ * update_mac(): API to inform the change in the mac address.
  *
- * @param cdev
- * @param mac
+ * @cdev: Qed dev pointer.
+ * @mac: MAC.
  *
+ * Return: Int.
  */
-	int (*update_mac)(struct qed_dev *cdev, u8 *mac);
+	int (*update_mac)(struct qed_dev *cdev, const u8 *mac);
 
 /**
- * @brief update_mtu - API to inform the change in the mtu
+ * update_mtu(): API to inform the change in the mtu.
  *
- * @param cdev
- * @param mtu
+ * @cdev: Qed dev pointer.
+ * @mtu: MTU.
  *
+ * Return: Int.
  */
 	int (*update_mtu)(struct qed_dev *cdev, u16 mtu);
 
 /**
- * @brief update_wol - update of changes in the WoL configuration
+ * update_wol(): Update of changes in the WoL configuration.
+ *
+ * @cdev: Qed dev pointer.
+ * @enabled: true iff WoL should be enabled.
  *
- * @param cdev
- * @param enabled - true iff WoL should be enabled.
+ * Return: Int.
  */
 	int (*update_wol) (struct qed_dev *cdev, bool enabled);
 
 /**
- * @brief read_module_eeprom
+ * read_module_eeprom(): Read EEPROM.
  *
- * @param cdev
- * @param buf - buffer
- * @param dev_addr - PHY device memory region
- * @param offset - offset into eeprom contents to be read
- * @param len - buffer length, i.e., max bytes to be read
+ * @cdev: Qed dev pointer.
+ * @buf: buffer.
+ * @dev_addr: PHY device memory region.
+ * @offset: offset into eeprom contents to be read.
+ * @len: buffer length, i.e., max bytes to be read.
+ *
+ * Return: Int.
  */
 	int (*read_module_eeprom)(struct qed_dev *cdev,
 				  char *buf, u8 dev_addr, u32 offset, u32 len);
 
 /**
- * @brief get_affin_hwfn_idx
+ * get_affin_hwfn_idx(): Get affine HW function.
+ *
+ * @cdev: Qed dev pointer.
  *
- * @param cdev
+ * Return: u8.
  */
 	u8 (*get_affin_hwfn_idx)(struct qed_dev *cdev);
 
 /**
- * @brief read_nvm_cfg - Read NVM config attribute value.
- * @param cdev
- * @param buf - buffer
- * @param cmd - NVM CFG command id
- * @param entity_id - Entity id
+ * read_nvm_cfg(): Read NVM config attribute value.
+ *
+ * @cdev: Qed dev pointer.
+ * @buf: Buffer.
+ * @cmd: NVM CFG command id.
+ * @entity_id: Entity id.
  *
+ * Return: Int.
  */
 	int (*read_nvm_cfg)(struct qed_dev *cdev, u8 **buf, u32 cmd,
 			    u32 entity_id);
 /**
- * @brief read_nvm_cfg - Read NVM config attribute value.
- * @param cdev
- * @param cmd - NVM CFG command id
+ * read_nvm_cfg_len(): Read NVM config attribute value.
  *
- * @return config id length, 0 on error.
+ * @cdev: Qed dev pointer.
+ * @cmd: NVM CFG command id.
+ *
+ * Return: config id length, 0 on error.
  */
 	int (*read_nvm_cfg_len)(struct qed_dev *cdev, u32 cmd);
 
 /**
- * @brief set_grc_config - Configure value for grc config id.
- * @param cdev
- * @param cfg_id - grc config id
- * @param val - grc config value
+ * set_grc_config(): Configure value for grc config id.
+ *
+ * @cdev: Qed dev pointer.
+ * @cfg_id: grc config id
+ * @val: grc config value
  *
+ * Return: Int.
  */
 	int (*set_grc_config)(struct qed_dev *cdev, u32 cfg_id, u32 val);
 
@@ -1397,18 +1422,16 @@
 }
 
 /**
+ * qed_sb_ack(): This function creates an update command for interrupts
+ *               that is  written to the IGU.
  *
- * @brief This function creates an update command for interrupts that is
- *        written to the IGU.
- *
- * @param sb_info       - This is the structure allocated and
- *                 initialized per status block. Assumption is
- *                 that it was initialized using qed_sb_init
- * @param int_cmd       - Enable/Disable/Nop
- * @param upd_flg       - whether igu consumer should be
- *                 updated.
+ * @sb_info: This is the structure allocated and
+ *           initialized per status block. Assumption is
+ *           that it was initialized using qed_sb_init
+ * @int_cmd: Enable/Disable/Nop
+ * @upd_flg: Whether igu consumer should be updated.
  *
- * @return inline void
+ * Return: inline void.
  */
 static inline void qed_sb_ack(struct qed_sb_info *sb_info,
 			      enum igu_int_cmd int_cmd,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_iscsi_if.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_iscsi_if.h
@@ -182,7 +182,7 @@
  *			@param stats - pointer to struck that would be filled
  *				we stats
  *			@return 0 on success, error otherwise.
- * @change_mac		Change MAC of interface
+ * @change_mac:		Change MAC of interface
  *			@param cdev
  *			@param handle - the connection handle.
  *			@param mac - new MAC to configure.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_ll2_if.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_ll2_if.h
@@ -208,57 +208,57 @@
 
 struct qed_ll2_ops {
 /**
- * @brief start - initializes ll2
+ * start(): Initializes ll2.
  *
- * @param cdev
- * @param params - protocol driver configuration for the ll2.
+ * @cdev: Qed dev pointer.
+ * @params: Protocol driver configuration for the ll2.
  *
- * @return 0 on success, otherwise error value.
+ * Return: 0 on success, otherwise error value.
  */
 	int (*start)(struct qed_dev *cdev, struct qed_ll2_params *params);
 
 /**
- * @brief stop - stops the ll2
+ * stop(): Stops the ll2
  *
- * @param cdev
+ * @cdev: Qed dev pointer.
  *
- * @return 0 on success, otherwise error value.
+ * Return: 0 on success, otherwise error value.
  */
 	int (*stop)(struct qed_dev *cdev);
 
 /**
- * @brief start_xmit - transmits an skb over the ll2 interface
+ * start_xmit(): Transmits an skb over the ll2 interface
  *
- * @param cdev
- * @param skb
- * @param xmit_flags - Transmit options defined by the enum qed_ll2_xmit_flags.
+ * @cdev: Qed dev pointer.
+ * @skb: SKB.
+ * @xmit_flags: Transmit options defined by the enum qed_ll2_xmit_flags.
  *
- * @return 0 on success, otherwise error value.
+ * Return: 0 on success, otherwise error value.
  */
 	int (*start_xmit)(struct qed_dev *cdev, struct sk_buff *skb,
 			  unsigned long xmit_flags);
 
 /**
- * @brief register_cb_ops - protocol driver register the callback for Rx/Tx
+ * register_cb_ops(): Protocol driver register the callback for Rx/Tx
  * packets. Should be called before `start'.
  *
- * @param cdev
- * @param cookie - to be passed to the callback functions.
- * @param ops - the callback functions to register for Rx / Tx.
+ * @cdev: Qed dev pointer.
+ * @cookie: to be passed to the callback functions.
+ * @ops: the callback functions to register for Rx / Tx.
  *
- * @return 0 on success, otherwise error value.
+ * Return: 0 on success, otherwise error value.
  */
 	void (*register_cb_ops)(struct qed_dev *cdev,
 				const struct qed_ll2_cb_ops *ops,
 				void *cookie);
 
 /**
- * @brief get LL2 related statistics
+ * get_stats(): Get LL2 related statistics.
  *
- * @param cdev
- * @param stats - pointer to struct that would be filled with stats
+ * @cdev: Qed dev pointer.
+ * @stats: Pointer to struct that would be filled with stats.
  *
- * @return 0 on success, error otherwise.
+ * Return: 0 on success, error otherwise.
  */
 	int (*get_stats)(struct qed_dev *cdev, struct qed_ll2_stats *stats);
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_nvmetcp_if.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_nvmetcp_if.h
@@ -171,6 +171,23 @@
  *			@param dest_port
  * @clear_all_filters: Clear all filters.
  *			@param cdev
+ * @init_read_io: Init read IO.
+ *			@task_params
+ *			@cmd_pdu_header
+ *			@nvme_cmd
+ *			@sgl_task_params
+ * @init_write_io: Init write IO.
+ *			@task_params
+ *			@cmd_pdu_header
+ *			@nvme_cmd
+ *			@sgl_task_params
+ * @init_icreq_exchange: Exchange ICReq.
+ *			@task_params
+ *			@init_conn_req_pdu_hdr
+ *			@tx_sgl_task_params
+ *			@rx_sgl_task_params
+ * @init_task_cleanup: Init task cleanup.
+ *			@task_params
  */
 struct qed_nvmetcp_ops {
 	const struct qed_common_ops *common;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/qed/qed_rdma_if.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/qed/qed_rdma_if.h
@@ -662,7 +662,8 @@
 			     u8 connection_handle,
 			     struct qed_ll2_stats *p_stats);
 	int (*ll2_set_mac_filter)(struct qed_dev *cdev,
-				  u8 *old_mac_address, u8 *new_mac_address);
+				  u8 *old_mac_address,
+				  const u8 *new_mac_address);
 
 	int (*iwarp_set_engine_affin)(struct qed_dev *cdev, bool b_reset);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/quota.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/quota.h
@@ -285,7 +285,9 @@
 #define DQ_FAKE_B	3	/* no limits only usage */
 #define DQ_READ_B	4	/* dquot was read into memory */
 #define DQ_ACTIVE_B	5	/* dquot is active (dquot_release not called) */
-#define DQ_LASTSET_B	6	/* Following 6 bits (see QIF_) are reserved\
+#define DQ_RELEASING_B	6	/* dquot is in releasing_dquots list waiting
+				 * to be cleaned up */
+#define DQ_LASTSET_B	7	/* Following 6 bits (see QIF_) are reserved\
 				 * for the mask of entries set via SETQUOTA\
 				 * quotactl. They are set under dq_data_lock\
 				 * and the quota format handling dquot can\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/quotaops.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/quotaops.h
@@ -56,7 +56,7 @@
 {
 	if (test_bit(DQ_MOD_B, &dquot->dq_flags))
 		return true;
-	if (atomic_read(&dquot->dq_count) > 1)
+	if (atomic_read(&dquot->dq_count) > 0)
 		return true;
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/radix-tree.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/radix-tree.h
@@ -17,20 +17,11 @@
 #include <linux/spinlock.h>
 #include <linux/types.h>
 #include <linux/xarray.h>
-#include <linux/local_lock.h>
 
 /* Keep unconverted code working */
 #define radix_tree_root		xarray
 #define radix_tree_node		xa_node
 
-struct radix_tree_preload {
-	local_lock_t lock;
-	unsigned nr;
-	/* nodes->parent points to next preallocated node */
-	struct radix_tree_node *nodes;
-};
-DECLARE_PER_CPU(struct radix_tree_preload, radix_tree_preloads);
-
 /*
  * The bottom two bits of the slot determine how the remaining bits in the
  * slot are interpreted:
@@ -255,7 +246,7 @@
 
 static inline void radix_tree_preload_end(void)
 {
-	local_unlock(&radix_tree_preloads.lock);
+	preempt_enable();
 }
 
 void __rcu **idr_get_free(struct radix_tree_root *root,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/raid_class.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/raid_class.h
@@ -77,7 +77,3 @@
 	
 struct raid_template *raid_class_attach(struct raid_function_template *);
 void raid_class_release(struct raid_template *);
-
-int __must_check raid_component_add(struct raid_template *, struct device *,
-				    struct device *);
-
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ramfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ramfs.h
@@ -7,6 +7,7 @@
 struct inode *ramfs_get_inode(struct super_block *sb, const struct inode *dir,
 	 umode_t mode, dev_t dev);
 extern int ramfs_init_fs_context(struct fs_context *fc);
+extern void ramfs_kill_sb(struct super_block *sb);
 
 #ifdef CONFIG_MMU
 static inline int
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/random.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/random.h
@@ -1,9 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-/*
- * include/linux/random.h
- *
- * Include file for the random number generator.
- */
+
 #ifndef _LINUX_RANDOM_H
 #define _LINUX_RANDOM_H
 
@@ -14,41 +10,26 @@
 
 #include <uapi/linux/random.h>
 
-struct random_ready_callback {
-	struct list_head list;
-	void (*func)(struct random_ready_callback *rdy);
-	struct module *owner;
-};
+struct notifier_block;
 
-extern void add_device_randomness(const void *, unsigned int);
-extern void add_bootloader_randomness(const void *, unsigned int);
+void add_device_randomness(const void *buf, size_t len);
+void __init add_bootloader_randomness(const void *buf, size_t len);
+void add_input_randomness(unsigned int type, unsigned int code,
+			  unsigned int value) __latent_entropy;
+void add_interrupt_randomness(int irq) __latent_entropy;
+void add_hwgenerator_randomness(const void *buf, size_t len, size_t entropy);
 
-#if defined(LATENT_ENTROPY_PLUGIN) && !defined(__CHECKER__)
 static inline void add_latent_entropy(void)
 {
-	add_device_randomness((const void *)&latent_entropy,
-			      sizeof(latent_entropy));
-}
+#if defined(LATENT_ENTROPY_PLUGIN) && !defined(__CHECKER__)
+	add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
 #else
-static inline void add_latent_entropy(void) {}
-#endif
-
-extern void add_input_randomness(unsigned int type, unsigned int code,
-				 unsigned int value) __latent_entropy;
-extern void add_interrupt_randomness(int irq, int irq_flags) __latent_entropy;
-
-extern void get_random_bytes(void *buf, int nbytes);
-extern int wait_for_random_bytes(void);
-extern int __init rand_initialize(void);
-extern bool rng_is_initialized(void);
-extern int add_random_ready_callback(struct random_ready_callback *rdy);
-extern void del_random_ready_callback(struct random_ready_callback *rdy);
-extern int __must_check get_random_bytes_arch(void *buf, int nbytes);
-
-#ifndef MODULE
-extern const struct file_operations random_fops, urandom_fops;
+	add_device_randomness(NULL, 0);
 #endif
+}
 
+void get_random_bytes(void *buf, size_t len);
+size_t __must_check get_random_bytes_arch(void *buf, size_t len);
 u32 get_random_u32(void);
 u64 get_random_u64(void);
 static inline unsigned int get_random_int(void)
@@ -80,36 +61,38 @@
 
 static inline unsigned long get_random_canary(void)
 {
-	unsigned long val = get_random_long();
-
-	return val & CANARY_MASK;
+	return get_random_long() & CANARY_MASK;
 }
 
+int __init random_init(const char *command_line);
+bool rng_is_initialized(void);
+int wait_for_random_bytes(void);
+int register_random_ready_notifier(struct notifier_block *nb);
+int unregister_random_ready_notifier(struct notifier_block *nb);
+
 /* Calls wait_for_random_bytes() and then calls get_random_bytes(buf, nbytes).
  * Returns the result of the call to wait_for_random_bytes. */
-static inline int get_random_bytes_wait(void *buf, int nbytes)
+static inline int get_random_bytes_wait(void *buf, size_t nbytes)
 {
 	int ret = wait_for_random_bytes();
 	get_random_bytes(buf, nbytes);
 	return ret;
 }
 
-#define declare_get_random_var_wait(var) \
-	static inline int get_random_ ## var ## _wait(var *out) { \
+#define declare_get_random_var_wait(name, ret_type) \
+	static inline int get_random_ ## name ## _wait(ret_type *out) { \
 		int ret = wait_for_random_bytes(); \
 		if (unlikely(ret)) \
 			return ret; \
-		*out = get_random_ ## var(); \
+		*out = get_random_ ## name(); \
 		return 0; \
 	}
-declare_get_random_var_wait(u32)
-declare_get_random_var_wait(u64)
-declare_get_random_var_wait(int)
-declare_get_random_var_wait(long)
+declare_get_random_var_wait(u32, u32)
+declare_get_random_var_wait(u64, u32)
+declare_get_random_var_wait(int, unsigned int)
+declare_get_random_var_wait(long, unsigned long)
 #undef declare_get_random_var
 
-unsigned long randomize_page(unsigned long start, unsigned long range);
-
 /*
  * This is designed to be standalone for just prandom
  * users, but for now we include it from <linux/random.h>
@@ -120,22 +103,10 @@
 #ifdef CONFIG_ARCH_RANDOM
 # include <asm/archrandom.h>
 #else
-static inline bool __must_check arch_get_random_long(unsigned long *v)
-{
-	return false;
-}
-static inline bool __must_check arch_get_random_int(unsigned int *v)
-{
-	return false;
-}
-static inline bool __must_check arch_get_random_seed_long(unsigned long *v)
-{
-	return false;
-}
-static inline bool __must_check arch_get_random_seed_int(unsigned int *v)
-{
-	return false;
-}
+static inline bool __must_check arch_get_random_long(unsigned long *v) { return false; }
+static inline bool __must_check arch_get_random_int(unsigned int *v) { return false; }
+static inline bool __must_check arch_get_random_seed_long(unsigned long *v) { return false; }
+static inline bool __must_check arch_get_random_seed_int(unsigned int *v) { return false; }
 #endif
 
 /*
@@ -158,4 +129,13 @@
 }
 #endif
 
+#ifdef CONFIG_SMP
+int random_prepare_cpu(unsigned int cpu);
+int random_online_cpu(unsigned int cpu);
+#endif
+
+#ifndef MODULE
+extern const struct file_operations random_fops, urandom_fops;
+#endif
+
 #endif /* _LINUX_RANDOM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/randomize_kstack.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/randomize_kstack.h
@@ -16,8 +16,20 @@
  * alignment. Also, since this use is being explicitly masked to a max of
  * 10 bits, stack-clash style attacks are unlikely. For more details see
  * "VLAs" in Documentation/process/deprecated.rst
+ *
+ * The normal __builtin_alloca() is initialized with INIT_STACK_ALL (currently
+ * only with Clang and not GCC). Initializing the unused area on each syscall
+ * entry is expensive, and generating an implicit call to memset() may also be
+ * problematic (such as in noinstr functions). Therefore, if the compiler
+ * supports it (which it should if it initializes allocas), always use the
+ * "uninitialized" variant of the builtin.
  */
-void *__builtin_alloca(size_t size);
+#if __has_builtin(__builtin_alloca_uninitialized)
+#define __kstack_alloca __builtin_alloca_uninitialized
+#else
+#define __kstack_alloca __builtin_alloca
+#endif
+
 /*
  * Use, at most, 10 bits of entropy. We explicitly cap this to keep the
  * "VLA" from being unbounded (see above). 10 bits leaves enough room for
@@ -36,7 +48,7 @@
 	if (static_branch_maybe(CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT,	\
 				&randomize_kstack_offset)) {		\
 		u32 offset = raw_cpu_read(kstack_offset);		\
-		u8 *ptr = __builtin_alloca(KSTACK_OFFSET_MAX(offset));	\
+		u8 *ptr = __kstack_alloca(KSTACK_OFFSET_MAX(offset));	\
 		/* Keep allocation even after "ptr" loses scope. */	\
 		asm volatile("" :: "r"(ptr) : "memory");		\
 	}								\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ratelimit_types.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ratelimit_types.h
@@ -23,12 +23,16 @@
 	unsigned long	flags;
 };
 
-#define RATELIMIT_STATE_INIT(name, interval_init, burst_init) {		\
-		.lock		= __RAW_SPIN_LOCK_UNLOCKED(name.lock),	\
-		.interval	= interval_init,			\
-		.burst		= burst_init,				\
+#define RATELIMIT_STATE_INIT_FLAGS(name, interval_init, burst_init, flags_init) { \
+		.lock		= __RAW_SPIN_LOCK_UNLOCKED(name.lock),		  \
+		.interval	= interval_init,				  \
+		.burst		= burst_init,					  \
+		.flags		= flags_init,					  \
 	}
 
+#define RATELIMIT_STATE_INIT(name, interval_init, burst_init) \
+	RATELIMIT_STATE_INIT_FLAGS(name, interval_init, burst_init, 0)
+
 #define RATELIMIT_STATE_INIT_DISABLED					\
 	RATELIMIT_STATE_INIT(ratelimit_state, 0, DEFAULT_RATELIMIT_BURST)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/rbtree_latch.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/rbtree_latch.h
@@ -206,7 +206,7 @@
 	do {
 		seq = raw_read_seqcount_latch(&root->seq);
 		node = __lt_find(key, root, seq & 1, ops->comp);
-	} while (read_seqcount_latch_retry(&root->seq, seq));
+	} while (raw_read_seqcount_latch_retry(&root->seq, seq));
 
 	return node;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/rcupdate.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/rcupdate.h
@@ -193,6 +193,7 @@
 
 #define rcu_note_voluntary_context_switch(t) rcu_tasks_qs(t, false)
 void exit_tasks_rcu_start(void);
+void exit_tasks_rcu_stop(void);
 void exit_tasks_rcu_finish(void);
 #else /* #ifdef CONFIG_TASKS_RCU_GENERIC */
 #define rcu_tasks_qs(t, preempt) do { } while (0)
@@ -200,10 +201,23 @@
 #define call_rcu_tasks call_rcu
 #define synchronize_rcu_tasks synchronize_rcu
 static inline void exit_tasks_rcu_start(void) { }
+static inline void exit_tasks_rcu_stop(void) { }
 static inline void exit_tasks_rcu_finish(void) { }
 #endif /* #else #ifdef CONFIG_TASKS_RCU_GENERIC */
 
 /**
+ * rcu_trace_implies_rcu_gp - does an RCU Tasks Trace grace period imply an RCU grace period?
+ *
+ * As an accident of implementation, an RCU Tasks Trace grace period also
+ * acts as an RCU grace period.  However, this could change at any time.
+ * Code relying on this accident must call this function to verify that
+ * this accident is still happening.
+ *
+ * You have been warned!
+ */
+static inline bool rcu_trace_implies_rcu_gp(void) { return true; }
+
+/**
  * cond_resched_tasks_rcu_qs - Report potential quiescent states to RCU
  *
  * This macro resembles cond_resched(), except that it is defined to
@@ -216,6 +230,37 @@
 	cond_resched(); \
 } while (0)
 
+/**
+ * rcu_softirq_qs_periodic - Report RCU and RCU-Tasks quiescent states
+ * @old_ts: jiffies at start of processing.
+ *
+ * This helper is for long-running softirq handlers, such as NAPI threads in
+ * networking. The caller should initialize the variable passed in as @old_ts
+ * at the beginning of the softirq handler. When invoked frequently, this macro
+ * will invoke rcu_softirq_qs() every 100 milliseconds thereafter, which will
+ * provide both RCU and RCU-Tasks quiescent states. Note that this macro
+ * modifies its old_ts argument.
+ *
+ * Because regions of code that have disabled softirq act as RCU read-side
+ * critical sections, this macro should be invoked with softirq (and
+ * preemption) enabled.
+ *
+ * The macro is not needed when CONFIG_PREEMPT_RT is defined. RT kernels would
+ * have more chance to invoke schedule() calls and provide necessary quiescent
+ * states. As a contrast, calling cond_resched() only won't achieve the same
+ * effect because cond_resched() does not provide RCU-Tasks quiescent states.
+ */
+#define rcu_softirq_qs_periodic(old_ts) \
+do { \
+	if (!IS_ENABLED(CONFIG_PREEMPT_RT) && \
+	    time_after(jiffies, (old_ts) + HZ / 10)) { \
+		preempt_disable(); \
+		rcu_softirq_qs(); \
+		preempt_enable(); \
+		(old_ts) = jiffies; \
+	} \
+} while (0)
+
 /*
  * Infrastructure to implement the synchronize_() primitives in
  * TREE_RCU and rcu_barrier_() primitives in TINY_RCU.
@@ -311,11 +356,18 @@
  * RCU_LOCKDEP_WARN - emit lockdep splat if specified condition is met
  * @c: condition to check
  * @s: informative message
+ *
+ * This checks debug_lockdep_rcu_enabled() before checking (c) to
+ * prevent early boot splats due to lockdep not yet being initialized,
+ * and rechecks it after checking (c) to prevent false-positive splats
+ * due to races with lockdep being disabled.  See commit 3066820034b5dd
+ * ("rcu: Reject RCU_LOCKDEP_WARN() false positives") for more detail.
  */
 #define RCU_LOCKDEP_WARN(c, s)						\
 	do {								\
 		static bool __section(".data.unlikely") __warned;	\
-		if ((c) && debug_lockdep_rcu_enabled() && !__warned) {	\
+		if (debug_lockdep_rcu_enabled() && (c) &&		\
+		    debug_lockdep_rcu_enabled() && !__warned) {		\
 			__warned = true;				\
 			lockdep_rcu_suspicious(__FILE__, __LINE__, s);	\
 		}							\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ref_tracker.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ref_tracker.h
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+#ifndef _LINUX_REF_TRACKER_H
+#define _LINUX_REF_TRACKER_H
+#include <linux/refcount.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+
+struct ref_tracker;
+
+struct ref_tracker_dir {
+#ifdef CONFIG_REF_TRACKER
+	spinlock_t		lock;
+	unsigned int		quarantine_avail;
+	refcount_t		untracked;
+	struct list_head	list; /* List of active trackers */
+	struct list_head	quarantine; /* List of dead trackers */
+#endif
+};
+
+#ifdef CONFIG_REF_TRACKER
+static inline void ref_tracker_dir_init(struct ref_tracker_dir *dir,
+					unsigned int quarantine_count)
+{
+	INIT_LIST_HEAD(&dir->list);
+	INIT_LIST_HEAD(&dir->quarantine);
+	spin_lock_init(&dir->lock);
+	dir->quarantine_avail = quarantine_count;
+	refcount_set(&dir->untracked, 1);
+}
+
+void ref_tracker_dir_exit(struct ref_tracker_dir *dir);
+
+void ref_tracker_dir_print(struct ref_tracker_dir *dir,
+			   unsigned int display_limit);
+
+int ref_tracker_alloc(struct ref_tracker_dir *dir,
+		      struct ref_tracker **trackerp, gfp_t gfp);
+
+int ref_tracker_free(struct ref_tracker_dir *dir,
+		     struct ref_tracker **trackerp);
+
+#else /* CONFIG_REF_TRACKER */
+
+static inline void ref_tracker_dir_init(struct ref_tracker_dir *dir,
+					unsigned int quarantine_count)
+{
+}
+
+static inline void ref_tracker_dir_exit(struct ref_tracker_dir *dir)
+{
+}
+
+static inline void ref_tracker_dir_print(struct ref_tracker_dir *dir,
+					 unsigned int display_limit)
+{
+}
+
+static inline int ref_tracker_alloc(struct ref_tracker_dir *dir,
+				    struct ref_tracker **trackerp,
+				    gfp_t gfp)
+{
+	return 0;
+}
+
+static inline int ref_tracker_free(struct ref_tracker_dir *dir,
+				   struct ref_tracker **trackerp)
+{
+	return 0;
+}
+
+#endif
+
+#endif /* _LINUX_REF_TRACKER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/regmap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/regmap.h
@@ -290,6 +290,17 @@
  *		  read operation on a bus such as SPI, I2C, etc. Most of the
  *		  devices do not need this.
  * @reg_write:	  Same as above for writing.
+ * @reg_update_bits: Optional callback that if filled will be used to perform
+ *		     all the update_bits(rmw) operation. Should only be provided
+ *		     if the function require special handling with lock and reg
+ *		     handling and the operation cannot be represented as a simple
+ *		     update_bits operation on a bus such as SPI, I2C, etc.
+ * @read: Optional callback that if filled will be used to perform all the
+ *        bulk reads from the registers. Data is returned in the buffer used
+ *        to transmit data.
+ * @write: Same as above for writing.
+ * @max_raw_read: Max raw read size that can be used on the device.
+ * @max_raw_write: Max raw write size that can be used on the device.
  * @fast_io:	  Register IO is fast. Use a spinlock instead of a mutex
  *	     	  to perform locking. This field is ignored if custom lock/unlock
  *	     	  functions are used (see fields lock/unlock of struct regmap_config).
@@ -372,6 +383,14 @@
 
 	int (*reg_read)(void *context, unsigned int reg, unsigned int *val);
 	int (*reg_write)(void *context, unsigned int reg, unsigned int val);
+	int (*reg_update_bits)(void *context, unsigned int reg,
+			       unsigned int mask, unsigned int val);
+	/* Bulk read/write */
+	int (*read)(void *context, const void *reg_buf, size_t reg_size,
+		    void *val_buf, size_t val_size);
+	int (*write)(void *context, const void *data, size_t count);
+	size_t max_raw_read;
+	size_t max_raw_write;
 
 	bool fast_io;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/regulator/pca9450.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/regulator/pca9450.h
@@ -196,11 +196,11 @@
 
 /* PCA9450_REG_LDO3_VOLT bits */
 #define LDO3_EN_MASK			0xC0
-#define LDO3OUT_MASK			0x0F
+#define LDO3OUT_MASK			0x1F
 
 /* PCA9450_REG_LDO4_VOLT bits */
 #define LDO4_EN_MASK			0xC0
-#define LDO4OUT_MASK			0x0F
+#define LDO4OUT_MASK			0x1F
 
 /* PCA9450_REG_LDO5_VOLT bits */
 #define LDO5L_EN_MASK			0xC0
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/remoteproc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/remoteproc.h
@@ -366,6 +366,8 @@
  * @attach:	attach to a device that his already powered up
  * @detach:	detach from a device, leaving it powered up
  * @kick:	kick a virtqueue (virtqueue id given as a parameter)
+ * @peek_remote_kick: check if remote has kicked
+ * @ack_remote_kick: ack remote kick
  * @da_to_va:	optional platform hook to perform address translations
  * @parse_fw:	parse firmware to extract information (e.g. resource table)
  * @handle_rsc:	optional platform hook to handle vendor resources. Should return
@@ -390,6 +392,8 @@
 	int (*attach)(struct rproc *rproc);
 	int (*detach)(struct rproc *rproc);
 	void (*kick)(struct rproc *rproc, int vqid);
+	bool (*peek_remote_kick)(struct rproc *rproc, char *buf, size_t *len);
+	void (*ack_remote_kick)(struct rproc *rproc);
 	void * (*da_to_va)(struct rproc *rproc, u64 da, size_t len, bool *is_iomem);
 	int (*parse_fw)(struct rproc *rproc, const struct firmware *fw);
 	int (*handle_rsc)(struct rproc *rproc, u32 rsc_type, void *rsc,
@@ -525,6 +529,7 @@
  * @auto_boot: flag to indicate if remote processor should be auto-started
  * @dump_segments: list of segments in the firmware
  * @nb_vdev: number of vdev currently handled by rproc
+ * @sysfs_kick: allow kick remoteproc from sysfs
  * @elf_class: firmware ELF class
  * @elf_machine: firmware ELF machine
  * @cdev: character device of the rproc
@@ -564,6 +569,7 @@
 	bool auto_boot;
 	struct list_head dump_segments;
 	int nb_vdev;
+	int sysfs_kick;
 	u8 elf_class;
 	u16 elf_machine;
 	struct cdev cdev;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/reset.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/reset.h
@@ -711,7 +711,7 @@
 devm_reset_control_bulk_get_optional_exclusive(struct device *dev, int num_rstcs,
 					       struct reset_control_bulk_data *rstcs)
 {
-	return __devm_reset_control_bulk_get(dev, num_rstcs, rstcs, true, false, true);
+	return __devm_reset_control_bulk_get(dev, num_rstcs, rstcs, false, true, true);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/ring_buffer.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/ring_buffer.h
@@ -98,10 +98,11 @@
 	__ring_buffer_alloc((size), (flags), &__key);	\
 })
 
+typedef bool (*ring_buffer_cond_fn)(void *data);
 int ring_buffer_wait(struct trace_buffer *buffer, int cpu, int full);
 __poll_t ring_buffer_poll_wait(struct trace_buffer *buffer, int cpu,
-			  struct file *filp, poll_table *poll_table);
-
+			  struct file *filp, poll_table *poll_table, int full);
+void ring_buffer_wake_waiters(struct trace_buffer *buffer, int cpu);
 
 #define RING_BUFFER_ALL_CPUS -1
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/rmap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/rmap.h
@@ -39,12 +39,15 @@
 	atomic_t refcount;
 
 	/*
-	 * Count of child anon_vmas and VMAs which points to this anon_vma.
+	 * Count of child anon_vmas. Equals to the count of all anon_vmas that
+	 * have ->parent pointing to this one, including itself.
 	 *
 	 * This counter is used for making decision about reusing anon_vma
 	 * instead of forking new one. See comments in function anon_vma_clone.
 	 */
-	unsigned degree;
+	unsigned long num_children;
+	/* Count of VMAs whose ->anon_vma pointer points to this object. */
+	unsigned long num_active_vmas;
 
 	struct anon_vma *parent;	/* Parent of this anon_vma */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/rpmsg.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/rpmsg.h
@@ -41,7 +41,9 @@
  * rpmsg_device - device that belong to the rpmsg bus
  * @dev: the device struct
  * @id: device id (used to match between rpmsg drivers and devices)
- * @driver_override: driver name to force a match
+ * @driver_override: driver name to force a match; do not set directly,
+ *                   because core frees it; use driver_set_override() to
+ *                   set or clear it.
  * @src: local address
  * @dst: destination address
  * @ept: the rpmsg endpoint of this channel
@@ -51,7 +53,7 @@
 struct rpmsg_device {
 	struct device dev;
 	struct rpmsg_device_id id;
-	char *driver_override;
+	const char *driver_override;
 	u32 src;
 	u32 dst;
 	struct rpmsg_endpoint *ept;
@@ -163,6 +165,8 @@
 
 #if IS_ENABLED(CONFIG_RPMSG)
 
+int rpmsg_register_device_override(struct rpmsg_device *rpdev,
+				   const char *driver_override);
 int rpmsg_register_device(struct rpmsg_device *rpdev);
 int rpmsg_unregister_device(struct device *parent,
 			    struct rpmsg_channel_info *chinfo);
@@ -188,6 +192,12 @@
 
 #else
 
+static inline int rpmsg_register_device_override(struct rpmsg_device *rpdev,
+						 const char *driver_override)
+{
+	return -ENXIO;
+}
+
 static inline int rpmsg_register_device(struct rpmsg_device *rpdev)
 {
 	return -ENXIO;
@@ -231,7 +241,7 @@
 	/* This shouldn't be possible */
 	WARN_ON(1);
 
-	return ERR_PTR(-ENXIO);
+	return NULL;
 }
 
 static inline int rpmsg_send(struct rpmsg_endpoint *ept, void *data, int len)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/rtsx_pci.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/rtsx_pci.h
@@ -1095,7 +1095,7 @@
 	unsigned int	(*cd_deglitch)(struct rtsx_pcr *pcr);
 	int		(*conv_clk_and_div_n)(int clk, int dir);
 	void		(*fetch_vendor_settings)(struct rtsx_pcr *pcr);
-	void		(*force_power_down)(struct rtsx_pcr *pcr, u8 pm_state);
+	void		(*force_power_down)(struct rtsx_pcr *pcr, u8 pm_state, bool runtime);
 	void		(*stop_cmd)(struct rtsx_pcr *pcr);
 
 	void (*set_aspm)(struct rtsx_pcr *pcr, bool enable);
@@ -1201,8 +1201,6 @@
 	unsigned int			card_exist;
 
 	struct delayed_work		carddet_work;
-	struct delayed_work		idle_work;
-	struct delayed_work		rtd3_work;
 
 	spinlock_t			lock;
 	struct mutex			pcr_mutex;
@@ -1212,7 +1210,6 @@
 	unsigned int			cur_clock;
 	bool				remove_pci;
 	bool				msi_en;
-	bool				is_runtime_suspended;
 
 #define EXTRA_CAPS_SD_SDR50		(1 << 0)
 #define EXTRA_CAPS_SD_SDR104		(1 << 1)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/rtsx_usb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/rtsx_usb.h
@@ -54,8 +54,6 @@
 	struct usb_device	*pusb_dev;
 	struct usb_interface	*pusb_intf;
 	struct usb_sg_request	current_sg;
-	unsigned char		*iobuf;
-	dma_addr_t		iobuf_dma;
 
 	struct timer_list	sg_timer;
 	struct mutex		dev_mutex;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched.h
@@ -522,7 +522,7 @@
 	u64				nr_wakeups_passive;
 	u64				nr_wakeups_idle;
 #endif
-};
+} ____cacheline_aligned;
 
 struct sched_entity {
 	/* For load-balancing: */
@@ -538,8 +538,6 @@
 
 	u64				nr_migrations;
 
-	struct sched_statistics		statistics;
-
 #ifdef CONFIG_FAIR_GROUP_SCHED
 	int				depth;
 	struct sched_entity		*parent;
@@ -610,10 +608,6 @@
 	 * task has to wait for a replenishment to be performed at the
 	 * next firing of dl_timer.
 	 *
-	 * @dl_boosted tells if we are boosted due to DI. If so we are
-	 * outside bandwidth enforcement mechanism (but only until we
-	 * exit the critical section);
-	 *
 	 * @dl_yielded tells if task gave up the CPU before consuming
 	 * all its available runtime during the last job.
 	 *
@@ -803,6 +797,8 @@
 	struct uclamp_se		uclamp[UCLAMP_CNT];
 #endif
 
+	struct sched_statistics         stats;
+
 #ifdef CONFIG_PREEMPT_NOTIFIERS
 	/* List of struct preempt_notifier: */
 	struct hlist_head		preempt_notifiers;
@@ -878,9 +874,7 @@
 	unsigned			sched_reset_on_fork:1;
 	unsigned			sched_contributes_to_load:1;
 	unsigned			sched_migrated:1;
-#ifdef CONFIG_PSI
-	unsigned			sched_psi_wake_requeue:1;
-#endif
+	unsigned			sched_task_hot:1;
 
 	/* Force alignment to the next boundary: */
 	unsigned			:0;
@@ -933,7 +927,7 @@
 #endif
 #ifdef CONFIG_EVENTFD
 	/* Recursion prevention for eventfd_signal() */
-	unsigned			in_eventfd_signal:1;
+	unsigned			in_eventfd:1;
 #endif
 
 	unsigned long			atomic_flags; /* Flags requiring atomic access. */
@@ -1436,6 +1430,7 @@
 	int				pagefault_disabled;
 #ifdef CONFIG_MMU
 	struct task_struct		*oom_reaper_list;
+	struct timer_list		oom_reaper_timer;
 #endif
 #ifdef CONFIG_VMAP_STACK
 	struct vm_struct		*stack_vm_area;
@@ -1626,6 +1621,14 @@
 	if (tsk_state == TASK_IDLE)
 		state = TASK_REPORT_IDLE;
 
+	/*
+	 * We're lying here, but rather than expose a completely new task state
+	 * to userspace, we can make this appear as if the task has gone through
+	 * a regular rt_mutex_lock() call.
+	 */
+	if (tsk_state == TASK_RTLOCK_WAIT)
+		state = TASK_UNINTERRUPTIBLE;
+
 	return fls(state);
 }
 
@@ -1675,7 +1678,6 @@
 #define PF_MEMALLOC		0x00000800	/* Allocating memory */
 #define PF_NPROC_EXCEEDED	0x00001000	/* set_user() noticed that RLIMIT_NPROC was exceeded */
 #define PF_USED_MATH		0x00002000	/* If unset the fpu must be initialized before use */
-#define PF_USED_ASYNC		0x00004000	/* Used async_schedule*(), used by module init */
 #define PF_NOFREEZE		0x00008000	/* This thread should not be frozen */
 #define PF_FROZEN		0x00010000	/* Frozen for system suspend */
 #define PF_KSWAPD		0x00020000	/* I am kswapd */
@@ -1789,7 +1791,9 @@
 }
 
 extern int cpuset_cpumask_can_shrink(const struct cpumask *cur, const struct cpumask *trial);
-extern int task_can_attach(struct task_struct *p, const struct cpumask *cs_cpus_allowed);
+extern int task_can_attach(struct task_struct *p);
+extern int dl_bw_alloc(int cpu, u64 dl_bw);
+extern void dl_bw_free(int cpu, u64 dl_bw);
 #ifdef CONFIG_SMP
 extern void do_set_cpus_allowed(struct task_struct *p, const struct cpumask *new_mask);
 extern int set_cpus_allowed_ptr(struct task_struct *p, const struct cpumask *new_mask);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/idle.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/idle.h
@@ -11,7 +11,11 @@
 	CPU_MAX_IDLE_TYPES
 };
 
+#ifdef CONFIG_SMP
 extern void wake_up_if_idle(int cpu);
+#else
+static inline void wake_up_if_idle(int cpu) { }
+#endif
 
 /*
  * Idle thread specific functions to determine the need_resched
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/mm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/mm.h
@@ -106,6 +106,14 @@
 #endif /* CONFIG_MEMCG */
 
 #ifdef CONFIG_MMU
+#ifndef arch_get_mmap_end
+#define arch_get_mmap_end(addr)	(TASK_SIZE)
+#endif
+
+#ifndef arch_get_mmap_base
+#define arch_get_mmap_base(addr, base) (base)
+#endif
+
 extern void arch_pick_mmap_layout(struct mm_struct *mm,
 				  struct rlimit *rlim_stack);
 extern unsigned long
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/rt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/rt.h
@@ -39,20 +39,12 @@
 }
 extern void rt_mutex_setprio(struct task_struct *p, struct task_struct *pi_task);
 extern void rt_mutex_adjust_pi(struct task_struct *p);
-static inline bool tsk_is_pi_blocked(struct task_struct *tsk)
-{
-	return tsk->pi_blocked_on != NULL;
-}
 #else
 static inline struct task_struct *rt_mutex_get_top_task(struct task_struct *task)
 {
 	return NULL;
 }
 # define rt_mutex_adjust_pi(p)		do { } while (0)
-static inline bool tsk_is_pi_blocked(struct task_struct *tsk)
-{
-	return false;
-}
 #endif
 
 extern void normalize_rt_tasks(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/signal.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/signal.h
@@ -125,7 +125,7 @@
 #ifdef CONFIG_POSIX_TIMERS
 
 	/* POSIX.1b Interval Timers */
-	int			posix_timer_id;
+	unsigned int		next_posix_timer_id;
 	struct list_head	posix_timers;
 
 	/* ITIMER_REAL timer for the process */
@@ -318,7 +318,7 @@
 
 int force_sig_bnderr(void __user *addr, void __user *lower, void __user *upper);
 int force_sig_pkuerr(void __user *addr, u32 pkey);
-int force_sig_perf(void __user *addr, u32 type, u64 sig_data);
+int send_sig_perf(void __user *addr, u32 type, u64 sig_data);
 
 int force_sig_ptrace_errno_trap(int errno, void __user *addr);
 int force_sig_fault_trapno(int sig, int code, void __user *addr, int trapno);
@@ -338,6 +338,8 @@
 extern __must_check bool do_notify_parent(struct task_struct *, int);
 extern void __wake_up_parent(struct task_struct *p, struct task_struct *parent);
 extern void force_sig(int);
+extern void force_fatal_sig(int);
+extern void force_exit_sig(int);
 extern int send_sig(int, struct task_struct *, int);
 extern int zap_other_threads(struct task_struct *p);
 extern struct sigqueue *sigqueue_alloc(void);
@@ -345,6 +347,12 @@
 extern int send_sigqueue(struct sigqueue *, struct pid *, enum pid_type);
 extern int do_sigaction(int, struct k_sigaction *, struct k_sigaction *);
 
+static inline void clear_notify_signal(void)
+{
+	clear_thread_flag(TIF_NOTIFY_SIGNAL);
+	smp_mb__after_atomic();
+}
+
 static inline int restart_syscall(void)
 {
 	set_tsk_thread_flag(current, TIF_SIGPENDING);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/smt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/smt.h
@@ -12,7 +12,7 @@
 	return static_branch_likely(&sched_smt_present);
 }
 #else
-static inline bool sched_smt_active(void) { return false; }
+static __always_inline bool sched_smt_active(void) { return false; }
 #endif
 
 void arch_smt_update(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/sysctl.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/sysctl.h
@@ -7,20 +7,8 @@
 struct ctl_table;
 
 #ifdef CONFIG_DETECT_HUNG_TASK
-
-#ifdef CONFIG_SMP
-extern unsigned int sysctl_hung_task_all_cpu_backtrace;
-#else
-#define sysctl_hung_task_all_cpu_backtrace 0
-#endif /* CONFIG_SMP */
-
-extern int	     sysctl_hung_task_check_count;
-extern unsigned int  sysctl_hung_task_panic;
+/* used for hung_task and block/ */
 extern unsigned long sysctl_hung_task_timeout_secs;
-extern unsigned long sysctl_hung_task_check_interval_secs;
-extern int sysctl_hung_task_warnings;
-int proc_dohung_task_timeout_secs(struct ctl_table *table, int write,
-		void *buffer, size_t *lenp, loff_t *ppos);
 #else
 /* Avoid need for ifdefs elsewhere in the code */
 enum { sysctl_hung_task_timeout_secs = 0 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/task.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/task.h
@@ -34,6 +34,7 @@
 	int io_thread;
 	struct cgroup *cgrp;
 	struct css_set *cset;
+	unsigned int kill_seq;
 };
 
 /*
@@ -54,11 +55,14 @@
 extern void init_idle(struct task_struct *idle, int cpu);
 
 extern int sched_fork(unsigned long clone_flags, struct task_struct *p);
+extern void sched_cgroup_fork(struct task_struct *p, struct kernel_clone_args *kargs);
 extern void sched_post_fork(struct task_struct *p);
 extern void sched_dead(struct task_struct *p);
 
 void __noreturn do_task_dead(void);
+void __noreturn make_task_dead(int signr);
 
+extern void mm_cache_init(void);
 extern void proc_caches_init(void);
 
 extern void fork_init(void);
@@ -80,12 +84,11 @@
 extern void do_group_exit(int);
 
 extern void exit_files(struct task_struct *);
-extern void exit_itimers(struct signal_struct *);
+extern void exit_itimers(struct task_struct *);
 
 extern pid_t kernel_clone(struct kernel_clone_args *kargs);
 struct task_struct *create_io_thread(int (*fn)(void *), void *arg, int node);
 struct task_struct *fork_idle(int);
-struct mm_struct *copy_init_mm(void);
 extern pid_t kernel_thread(int (*fn)(void *), void *arg, unsigned long flags);
 extern long kernel_wait4(pid_t, int __user *, int, struct rusage *);
 int kernel_wait(pid_t pid, int *stat);
@@ -106,10 +109,36 @@
 }
 
 extern void __put_task_struct(struct task_struct *t);
+extern void __put_task_struct_rcu_cb(struct rcu_head *rhp);
 
 static inline void put_task_struct(struct task_struct *t)
 {
-	if (refcount_dec_and_test(&t->usage))
+	if (!refcount_dec_and_test(&t->usage))
+		return;
+
+	/*
+	 * under PREEMPT_RT, we can't call put_task_struct
+	 * in atomic context because it will indirectly
+	 * acquire sleeping locks.
+	 *
+	 * call_rcu() will schedule delayed_put_task_struct_rcu()
+	 * to be called in process context.
+	 *
+	 * __put_task_struct() is called when
+	 * refcount_dec_and_test(&t->usage) succeeds.
+	 *
+	 * This means that it can't "conflict" with
+	 * put_task_struct_rcu_user() which abuses ->rcu the same
+	 * way; rcu_users has a reference so task->usage can't be
+	 * zero after rcu_users 1 -> 0 transition.
+	 *
+	 * delayed_free_task() also uses ->rcu, but it is only called
+	 * when it fails to fork a process. Therefore, there is no
+	 * way it can conflict with put_task_struct().
+	 */
+	if (IS_ENABLED(CONFIG_PREEMPT_RT) && !preemptible())
+		call_rcu(&t->rcu, __put_task_struct_rcu_cb);
+	else
 		__put_task_struct(t);
 }
 
@@ -157,7 +186,7 @@
  * Protects ->fs, ->files, ->mm, ->group_info, ->comm, keyring
  * subscriptions and synchronises with wait4().  Also used in procfs.  Also
  * pins the final release of task.io_context.  Also protects ->cpuset and
- * ->cgroup.subsys[]. And ->vfork_done.
+ * ->cgroup.subsys[]. And ->vfork_done. And ->sysvshm.shm_clist.
  *
  * Nests both inside and outside of read_lock(&tasklist_lock).
  * It must not be nested with write_lock_irq(&tasklist_lock),
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/task_stack.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/task_stack.h
@@ -16,16 +16,20 @@
  * try_get_task_stack() instead.  task_stack_page will return a pointer
  * that could get freed out from under you.
  */
-static inline void *task_stack_page(const struct task_struct *task)
+static __always_inline void *task_stack_page(const struct task_struct *task)
 {
 	return task->stack;
 }
 
 #define setup_thread_stack(new,old)	do { } while(0)
 
-static inline unsigned long *end_of_stack(const struct task_struct *task)
+static __always_inline unsigned long *end_of_stack(const struct task_struct *task)
 {
+#ifdef CONFIG_STACK_GROWSUP
+	return (unsigned long *)((unsigned long)task->stack + THREAD_SIZE) - 1;
+#else
 	return task->stack;
+#endif
 }
 
 #elif !defined(__HAVE_THREAD_FUNCTIONS)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/topology.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/topology.h
@@ -74,6 +74,7 @@
 	atomic_t	ref;
 	atomic_t	nr_busy_cpus;
 	int		has_idle_cores;
+	int		nr_idle_scan;
 };
 
 struct sched_domain {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sched/user.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sched/user.h
@@ -24,7 +24,8 @@
 	kuid_t uid;
 
 #if defined(CONFIG_PERF_EVENTS) || defined(CONFIG_BPF_SYSCALL) || \
-    defined(CONFIG_NET) || defined(CONFIG_IO_URING)
+	defined(CONFIG_NET) || defined(CONFIG_IO_URING) || \
+	defined(CONFIG_VFIO_PCI_ZDEV_KVM)
 	atomic_long_t locked_vm;
 #endif
 #ifdef CONFIG_WATCH_QUEUE
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/scmi_protocol.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/scmi_protocol.h
@@ -74,7 +74,7 @@
 struct scmi_clk_proto_ops {
 	int (*count_get)(const struct scmi_protocol_handle *ph);
 
-	const struct scmi_clock_info *(*info_get)
+	const struct scmi_clock_info __must_check *(*info_get)
 		(const struct scmi_protocol_handle *ph, u32 clk_id);
 	int (*rate_get)(const struct scmi_protocol_handle *ph, u32 clk_id,
 			u64 *rate);
@@ -452,7 +452,7 @@
  */
 struct scmi_sensor_proto_ops {
 	int (*count_get)(const struct scmi_protocol_handle *ph);
-	const struct scmi_sensor_info *(*info_get)
+	const struct scmi_sensor_info __must_check *(*info_get)
 		(const struct scmi_protocol_handle *ph, u32 sensor_id);
 	int (*trip_point_config)(const struct scmi_protocol_handle *ph,
 				 u32 sensor_id, u8 trip_id, u64 trip_value);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/seccomp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/seccomp.h
@@ -68,10 +68,10 @@
 
 #ifdef CONFIG_HAVE_ARCH_SECCOMP_FILTER
 static inline int secure_computing(void) { return 0; }
-static inline int __secure_computing(const struct seccomp_data *sd) { return 0; }
 #else
 static inline void secure_computing_strict(int this_syscall) { return; }
 #endif
+static inline int __secure_computing(const struct seccomp_data *sd) { return 0; }
 
 static inline long prctl_get_seccomp(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/secretmem.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/secretmem.h
@@ -14,10 +14,10 @@
 	 * Using page_mapping() is quite slow because of the actual call
 	 * instruction and repeated compound_head(page) inside the
 	 * page_mapping() function.
-	 * We know that secretmem pages are not compound and LRU so we can
+	 * We know that secretmem pages are not compound, so we can
 	 * save a couple of cycles here.
 	 */
-	if (PageCompound(page) || !PageLRU(page))
+	if (PageCompound(page))
 		return false;
 
 	mapping = (struct address_space *)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/security.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/security.h
@@ -121,6 +121,7 @@
 	LOCKDOWN_DEBUGFS,
 	LOCKDOWN_XMON_WR,
 	LOCKDOWN_BPF_WRITE_USER,
+	LOCKDOWN_KGDB,
 	LOCKDOWN_INTEGRITY_MAX,
 	LOCKDOWN_KCORE,
 	LOCKDOWN_KPROBES,
@@ -134,6 +135,130 @@
 
 extern const char *const lockdown_reasons[LOCKDOWN_CONFIDENTIALITY_MAX+1];
 
+/*
+ * A "security context" is the text representation of
+ * the information used by LSMs.
+ * This structure contains the string, its length, and which LSM
+ * it is useful for.
+ */
+struct lsmcontext {
+	char	*context;	/* Provided by the module */
+	u32	len;
+	int	slot;		/* Identifies the module */
+};
+
+/**
+ * lsmcontext_init - initialize an lsmcontext structure.
+ * @cp: Pointer to the context to initialize
+ * @context: Initial context, or NULL
+ * @size: Size of context, or 0
+ * @slot: Which LSM provided the context
+ *
+ * Fill in the lsmcontext from the provided information.
+ * This is a scaffolding function that will be removed when
+ * lsmcontext integration is complete.
+ */
+static inline void lsmcontext_init(struct lsmcontext *cp, char *context,
+				   u32 size, int slot)
+{
+	cp->slot = slot;
+	cp->context = context;
+	cp->len = size;
+}
+
+/*
+ * Data exported by the security modules
+ *
+ * Any LSM that provides secid or secctx based hooks must be included.
+ */
+#define LSMBLOB_ENTRIES ( \
+	(IS_ENABLED(CONFIG_SECURITY_SELINUX) ? 1 : 0) + \
+	(IS_ENABLED(CONFIG_SECURITY_SMACK) ? 1 : 0) + \
+	(IS_ENABLED(CONFIG_SECURITY_APPARMOR) ? 1 : 0) + \
+	(IS_ENABLED(CONFIG_BPF_LSM) ? 1 : 0))
+
+struct lsmblob {
+	u32     secid[LSMBLOB_ENTRIES];
+};
+
+#define LSMBLOB_INVALID		-1	/* Not a valid LSM slot number */
+#define LSMBLOB_NEEDED		-2	/* Slot requested on initialization */
+#define LSMBLOB_NOT_NEEDED	-3	/* Slot not requested */
+#define LSMBLOB_DISPLAY		-4	/* Use the "display" slot */
+#define LSMBLOB_FIRST		-5	/* Use the default "display" slot */
+
+/**
+ * lsmblob_init - initialize an lsmblob structure.
+ * @blob: Pointer to the data to initialize
+ * @secid: The initial secid value
+ *
+ * Set all secid for all modules to the specified value.
+ */
+static inline void lsmblob_init(struct lsmblob *blob, u32 secid)
+{
+	int i;
+
+	for (i = 0; i < LSMBLOB_ENTRIES; i++)
+		blob->secid[i] = secid;
+}
+
+/**
+ * lsmblob_is_set - report if there is an value in the lsmblob
+ * @blob: Pointer to the exported LSM data
+ *
+ * Returns true if there is a secid set, false otherwise
+ */
+static inline bool lsmblob_is_set(struct lsmblob *blob)
+{
+	struct lsmblob empty = {};
+
+	return !!memcmp(blob, &empty, sizeof(*blob));
+}
+
+/**
+ * lsmblob_equal - report if the two lsmblob's are equal
+ * @bloba: Pointer to one LSM data
+ * @blobb: Pointer to the other LSM data
+ *
+ * Returns true if all entries in the two are equal, false otherwise
+ */
+static inline bool lsmblob_equal(struct lsmblob *bloba, struct lsmblob *blobb)
+{
+	return !memcmp(bloba, blobb, sizeof(*bloba));
+}
+
+/**
+ * lsmblob_value - find the first non-zero value in an lsmblob structure.
+ * @blob: Pointer to the data
+ *
+ * This needs to be used with extreme caution, as the cases where
+ * it is appropriate are rare.
+ *
+ * Return the first secid value set in the lsmblob.
+ * There should only be one.
+ */
+static inline u32 lsmblob_value(const struct lsmblob *blob)
+{
+	int i;
+
+	for (i = 0; i < LSMBLOB_ENTRIES; i++)
+		if (blob->secid[i])
+			return blob->secid[i];
+
+	return 0;
+}
+
+const char *security_lsm_slot_name(int slot);
+
+static inline bool lsm_multiple_contexts(void)
+{
+#ifdef CONFIG_SECURITY
+	return security_lsm_slot_name(1) != NULL;
+#else
+	return false;
+#endif
+}
+
 /* These functions are in security/commoncap.c */
 extern int cap_capable(const struct cred *cred, struct user_namespace *ns,
 		       int cap, unsigned int opts);
@@ -258,13 +383,13 @@
 extern int early_security_init(void);
 
 /* Security operations */
-int security_binder_set_context_mgr(struct task_struct *mgr);
-int security_binder_transaction(struct task_struct *from,
-				struct task_struct *to);
-int security_binder_transfer_binder(struct task_struct *from,
-				    struct task_struct *to);
-int security_binder_transfer_file(struct task_struct *from,
-				  struct task_struct *to, struct file *file);
+int security_binder_set_context_mgr(const struct cred *mgr);
+int security_binder_transaction(const struct cred *from,
+				const struct cred *to);
+int security_binder_transfer_binder(const struct cred *from,
+				    const struct cred *to);
+int security_binder_transfer_file(const struct cred *from,
+				  const struct cred *to, struct file *file);
 int security_ptrace_access_check(struct task_struct *child, unsigned int mode);
 int security_ptrace_traceme(struct task_struct *parent);
 int security_capget(struct task_struct *target,
@@ -371,7 +496,7 @@
 			       void **buffer, bool alloc);
 int security_inode_setsecurity(struct inode *inode, const char *name, const void *value, size_t size, int flags);
 int security_inode_listsecurity(struct inode *inode, char *buffer, size_t buffer_size);
-void security_inode_getsecid(struct inode *inode, u32 *secid);
+void security_inode_getsecid(struct inode *inode, struct lsmblob *blob);
 int security_inode_copy_up(struct dentry *src, struct cred **new);
 int security_inode_copy_up_xattr(const char *name);
 int security_kernfs_init_security(struct kernfs_node *kn_dir,
@@ -380,6 +505,8 @@
 int security_file_alloc(struct file *file);
 void security_file_free(struct file *file);
 int security_file_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
+int security_file_ioctl_compat(struct file *file, unsigned int cmd,
+			       unsigned long arg);
 int security_mmap_file(struct file *file, unsigned long prot,
 			unsigned long flags);
 int security_mmap_addr(unsigned long addr);
@@ -398,8 +525,8 @@
 void security_cred_free(struct cred *cred);
 int security_prepare_creds(struct cred *new, const struct cred *old, gfp_t gfp);
 void security_transfer_creds(struct cred *new, const struct cred *old);
-void security_cred_getsecid(const struct cred *c, u32 *secid);
-int security_kernel_act_as(struct cred *new, u32 secid);
+void security_cred_getsecid(const struct cred *c, struct lsmblob *blob);
+int security_kernel_act_as(struct cred *new, struct lsmblob *blob);
 int security_kernel_create_files_as(struct cred *new, struct inode *inode);
 int security_kernel_module_request(char *kmod_name);
 int security_kernel_load_data(enum kernel_load_data_id id, bool contents);
@@ -417,8 +544,8 @@
 int security_task_setpgid(struct task_struct *p, pid_t pgid);
 int security_task_getpgid(struct task_struct *p);
 int security_task_getsid(struct task_struct *p);
-void security_task_getsecid_subj(struct task_struct *p, u32 *secid);
-void security_task_getsecid_obj(struct task_struct *p, u32 *secid);
+void security_task_getsecid_subj(struct task_struct *p, struct lsmblob *blob);
+void security_task_getsecid_obj(struct task_struct *p, struct lsmblob *blob);
 int security_task_setnice(struct task_struct *p, int nice);
 int security_task_setioprio(struct task_struct *p, int ioprio);
 int security_task_getioprio(struct task_struct *p);
@@ -435,7 +562,7 @@
 			unsigned long arg4, unsigned long arg5);
 void security_task_to_inode(struct task_struct *p, struct inode *inode);
 int security_ipc_permission(struct kern_ipc_perm *ipcp, short flag);
-void security_ipc_getsecid(struct kern_ipc_perm *ipcp, u32 *secid);
+void security_ipc_getsecid(struct kern_ipc_perm *ipcp, struct lsmblob *blob);
 int security_msg_msg_alloc(struct msg_msg *msg);
 void security_msg_msg_free(struct msg_msg *msg);
 int security_msg_queue_alloc(struct kern_ipc_perm *msq);
@@ -464,14 +591,17 @@
 			 size_t size);
 int security_netlink_send(struct sock *sk, struct sk_buff *skb);
 int security_ismaclabel(const char *name);
-int security_secid_to_secctx(u32 secid, char **secdata, u32 *seclen);
-int security_secctx_to_secid(const char *secdata, u32 seclen, u32 *secid);
-void security_release_secctx(char *secdata, u32 seclen);
+int security_secid_to_secctx(struct lsmblob *blob, struct lsmcontext *cp,
+			     int display);
+int security_secctx_to_secid(const char *secdata, u32 seclen,
+			     struct lsmblob *blob);
+void security_release_secctx(struct lsmcontext *cp);
 void security_inode_invalidate_secctx(struct inode *inode);
 int security_inode_notifysecctx(struct inode *inode, void *ctx, u32 ctxlen);
 int security_inode_setsecctx(struct dentry *dentry, void *ctx, u32 ctxlen);
-int security_inode_getsecctx(struct inode *inode, void **ctx, u32 *ctxlen);
+int security_inode_getsecctx(struct inode *inode, struct lsmcontext *cp);
 int security_locked_down(enum lockdown_reason what);
+int security_lock_kernel_down(const char *where, enum lockdown_reason level);
 #else /* CONFIG_SECURITY */
 
 static inline int call_blocking_lsm_notifier(enum lsm_event event, void *data)
@@ -508,25 +638,25 @@
 	return 0;
 }
 
-static inline int security_binder_set_context_mgr(struct task_struct *mgr)
+static inline int security_binder_set_context_mgr(const struct cred *mgr)
 {
 	return 0;
 }
 
-static inline int security_binder_transaction(struct task_struct *from,
-					      struct task_struct *to)
+static inline int security_binder_transaction(const struct cred *from,
+					      const struct cred *to)
 {
 	return 0;
 }
 
-static inline int security_binder_transfer_binder(struct task_struct *from,
-						  struct task_struct *to)
+static inline int security_binder_transfer_binder(const struct cred *from,
+						  const struct cred *to)
 {
 	return 0;
 }
 
-static inline int security_binder_transfer_file(struct task_struct *from,
-						struct task_struct *to,
+static inline int security_binder_transfer_file(const struct cred *from,
+						const struct cred *to,
 						struct file *file)
 {
 	return 0;
@@ -921,9 +1051,10 @@
 	return 0;
 }
 
-static inline void security_inode_getsecid(struct inode *inode, u32 *secid)
+static inline void security_inode_getsecid(struct inode *inode,
+					   struct lsmblob *blob)
 {
-	*secid = 0;
+	lsmblob_init(blob, 0);
 }
 
 static inline int security_inode_copy_up(struct dentry *src, struct cred **new)
@@ -961,6 +1092,13 @@
 	return 0;
 }
 
+static inline int security_file_ioctl_compat(struct file *file,
+					     unsigned int cmd,
+					     unsigned long arg)
+{
+	return 0;
+}
+
 static inline int security_mmap_file(struct file *file, unsigned long prot,
 				     unsigned long flags)
 {
@@ -1041,7 +1179,13 @@
 {
 }
 
-static inline int security_kernel_act_as(struct cred *cred, u32 secid)
+static inline void security_cred_getsecid(const struct cred *c, u32 *secid)
+{
+	*secid = 0;
+}
+
+static inline int security_kernel_act_as(struct cred *cred,
+					 struct lsmblob *blob)
 {
 	return 0;
 }
@@ -1112,14 +1256,16 @@
 	return 0;
 }
 
-static inline void security_task_getsecid_subj(struct task_struct *p, u32 *secid)
+static inline void security_task_getsecid_subj(struct task_struct *p,
+					       struct lsmblob *blob)
 {
-	*secid = 0;
+	lsmblob_init(blob, 0);
 }
 
-static inline void security_task_getsecid_obj(struct task_struct *p, u32 *secid)
+static inline void security_task_getsecid_obj(struct task_struct *p,
+					      struct lsmblob *blob)
 {
-	*secid = 0;
+	lsmblob_init(blob, 0);
 }
 
 static inline int security_task_setnice(struct task_struct *p, int nice)
@@ -1190,9 +1336,10 @@
 	return 0;
 }
 
-static inline void security_ipc_getsecid(struct kern_ipc_perm *ipcp, u32 *secid)
+static inline void security_ipc_getsecid(struct kern_ipc_perm *ipcp,
+					 struct lsmblob *blob)
 {
-	*secid = 0;
+	lsmblob_init(blob, 0);
 }
 
 static inline int security_msg_msg_alloc(struct msg_msg *msg)
@@ -1312,19 +1459,20 @@
 	return 0;
 }
 
-static inline int security_secid_to_secctx(u32 secid, char **secdata, u32 *seclen)
+static inline int security_secid_to_secctx(struct lsmblob *blob,
+					   struct lsmcontext *cp, int display)
 {
 	return -EOPNOTSUPP;
 }
 
 static inline int security_secctx_to_secid(const char *secdata,
 					   u32 seclen,
-					   u32 *secid)
+					   struct lsmblob *blob)
 {
 	return -EOPNOTSUPP;
 }
 
-static inline void security_release_secctx(char *secdata, u32 seclen)
+static inline void security_release_secctx(struct lsmcontext *cp)
 {
 }
 
@@ -1340,7 +1488,8 @@
 {
 	return -EOPNOTSUPP;
 }
-static inline int security_inode_getsecctx(struct inode *inode, void **ctx, u32 *ctxlen)
+static inline int security_inode_getsecctx(struct inode *inode,
+					   struct lsmcontext *cp)
 {
 	return -EOPNOTSUPP;
 }
@@ -1348,6 +1497,10 @@
 {
 	return 0;
 }
+static inline int security_lock_kernel_down(const char *where, enum lockdown_reason level)
+{
+	return 0;
+}
 #endif	/* CONFIG_SECURITY */
 
 #if defined(CONFIG_SECURITY) && defined(CONFIG_WATCH_QUEUE)
@@ -1395,7 +1548,8 @@
 int security_sock_rcv_skb(struct sock *sk, struct sk_buff *skb);
 int security_socket_getpeersec_stream(struct socket *sock, char __user *optval,
 				      int __user *optlen, unsigned len);
-int security_socket_getpeersec_dgram(struct socket *sock, struct sk_buff *skb, u32 *secid);
+int security_socket_getpeersec_dgram(struct socket *sock, struct sk_buff *skb,
+				     struct lsmblob *blob);
 int security_sk_alloc(struct sock *sk, int family, gfp_t priority);
 void security_sk_free(struct sock *sk);
 void security_sk_clone(const struct sock *sk, struct sock *newsk);
@@ -1409,7 +1563,7 @@
 			const struct request_sock *req);
 void security_inet_conn_established(struct sock *sk,
 			struct sk_buff *skb);
-int security_secmark_relabel_packet(u32 secid);
+int security_secmark_relabel_packet(struct lsmblob *blob);
 void security_secmark_refcount_inc(void);
 void security_secmark_refcount_dec(void);
 int security_tun_dev_alloc_security(void **security);
@@ -1534,7 +1688,9 @@
 	return -ENOPROTOOPT;
 }
 
-static inline int security_socket_getpeersec_dgram(struct socket *sock, struct sk_buff *skb, u32 *secid)
+static inline int security_socket_getpeersec_dgram(struct socket *sock,
+						   struct sk_buff *skb,
+						   struct lsmblob *blob)
 {
 	return -ENOPROTOOPT;
 }
@@ -1582,7 +1738,7 @@
 {
 }
 
-static inline int security_secmark_relabel_packet(u32 secid)
+static inline int security_secmark_relabel_packet(struct lsmblob *blob)
 {
 	return 0;
 }
@@ -1880,15 +2036,17 @@
 
 #ifdef CONFIG_AUDIT
 #ifdef CONFIG_SECURITY
-int security_audit_rule_init(u32 field, u32 op, char *rulestr, void **lsmrule);
+int security_audit_rule_init(u32 field, u32 op, char *rulestr, void **lsmrule,
+			     gfp_t gfp);
 int security_audit_rule_known(struct audit_krule *krule);
-int security_audit_rule_match(u32 secid, u32 field, u32 op, void *lsmrule);
-void security_audit_rule_free(void *lsmrule);
+int security_audit_rule_match(struct lsmblob *blob, u32 field, u32 op,
+			      void **lsmrule);
+void security_audit_rule_free(void **lsmrule);
 
 #else
 
 static inline int security_audit_rule_init(u32 field, u32 op, char *rulestr,
-					   void **lsmrule)
+					   void **lsmrule, gfp_t gfp)
 {
 	return 0;
 }
@@ -1898,13 +2056,13 @@
 	return 0;
 }
 
-static inline int security_audit_rule_match(u32 secid, u32 field, u32 op,
-					    void *lsmrule)
+static inline int security_audit_rule_match(struct lsmblob *blob, u32 field,
+					    u32 op, void **lsmrule)
 {
 	return 0;
 }
 
-static inline void security_audit_rule_free(void *lsmrule)
+static inline void security_audit_rule_free(void **lsmrule)
 { }
 
 #endif /* CONFIG_SECURITY */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/seq_file.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/seq_file.h
@@ -194,7 +194,7 @@
 #define DEFINE_PROC_SHOW_ATTRIBUTE(__name)				\
 static int __name ## _open(struct inode *inode, struct file *file)	\
 {									\
-	return single_open(file, __name ## _show, inode->i_private);	\
+	return single_open(file, __name ## _show, PDE_DATA(inode));	\
 }									\
 									\
 static const struct proc_ops __name ## _proc_ops = {			\
@@ -261,6 +261,10 @@
 extern struct list_head *seq_list_next(void *v, struct list_head *head,
 		loff_t *ppos);
 
+extern struct list_head *seq_list_start_rcu(struct list_head *head, loff_t pos);
+extern struct list_head *seq_list_start_head_rcu(struct list_head *head, loff_t pos);
+extern struct list_head *seq_list_next_rcu(void *v, struct list_head *head, loff_t *ppos);
+
 /*
  * Helpers for iteration over hlist_head-s in seq_files
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/seqlock.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/seqlock.h
@@ -516,8 +516,8 @@
 
 static inline void do_write_seqcount_begin_nested(seqcount_t *s, int subclass)
 {
-	do_raw_write_seqcount_begin(s);
 	seqcount_acquire(&s->dep_map, subclass, 0, _RET_IP_);
+	do_raw_write_seqcount_begin(s);
 }
 
 /**
@@ -675,9 +675,9 @@
  *
  * Return: sequence counter raw value. Use the lowest bit as an index for
  * picking which data copy to read. The full counter must then be checked
- * with read_seqcount_latch_retry().
+ * with raw_read_seqcount_latch_retry().
  */
-static inline unsigned raw_read_seqcount_latch(const seqcount_latch_t *s)
+static __always_inline unsigned raw_read_seqcount_latch(const seqcount_latch_t *s)
 {
 	/*
 	 * Pairs with the first smp_wmb() in raw_write_seqcount_latch().
@@ -687,21 +687,64 @@
 }
 
 /**
- * read_seqcount_latch_retry() - end a seqcount_latch_t read section
+ * read_seqcount_latch() - pick even/odd latch data copy
+ * @s: Pointer to seqcount_latch_t
+ *
+ * See write_seqcount_latch() for details and a full reader/writer usage
+ * example.
+ *
+ * Return: sequence counter raw value. Use the lowest bit as an index for
+ * picking which data copy to read. The full counter must then be checked
+ * with read_seqcount_latch_retry().
+ */
+static __always_inline unsigned read_seqcount_latch(const seqcount_latch_t *s)
+{
+	kcsan_atomic_next(KCSAN_SEQLOCK_REGION_MAX);
+	return raw_read_seqcount_latch(s);
+}
+
+/**
+ * raw_read_seqcount_latch_retry() - end a seqcount_latch_t read section
  * @s:		Pointer to seqcount_latch_t
  * @start:	count, from raw_read_seqcount_latch()
  *
  * Return: true if a read section retry is required, else false
  */
-static inline int
+static __always_inline int
+raw_read_seqcount_latch_retry(const seqcount_latch_t *s, unsigned start)
+{
+	smp_rmb();
+	return unlikely(READ_ONCE(s->seqcount.sequence) != start);
+}
+
+/**
+ * read_seqcount_latch_retry() - end a seqcount_latch_t read section
+ * @s:		Pointer to seqcount_latch_t
+ * @start:	count, from read_seqcount_latch()
+ *
+ * Return: true if a read section retry is required, else false
+ */
+static __always_inline int
 read_seqcount_latch_retry(const seqcount_latch_t *s, unsigned start)
 {
-	return read_seqcount_retry(&s->seqcount, start);
+	kcsan_atomic_next(0);
+	return raw_read_seqcount_latch_retry(s, start);
 }
 
 /**
  * raw_write_seqcount_latch() - redirect latch readers to even/odd copy
  * @s: Pointer to seqcount_latch_t
+ */
+static __always_inline void raw_write_seqcount_latch(seqcount_latch_t *s)
+{
+	smp_wmb();	/* prior stores before incrementing "sequence" */
+	s->seqcount.sequence++;
+	smp_wmb();      /* increment "sequence" before following stores */
+}
+
+/**
+ * write_seqcount_latch_begin() - redirect latch readers to odd copy
+ * @s: Pointer to seqcount_latch_t
  *
  * The latch technique is a multiversion concurrency control method that allows
  * queries during non-atomic modifications. If you can guarantee queries never
@@ -729,17 +772,11 @@
  *
  *	void latch_modify(struct latch_struct *latch, ...)
  *	{
- *		smp_wmb();	// Ensure that the last data[1] update is visible
- *		latch->seq.sequence++;
- *		smp_wmb();	// Ensure that the seqcount update is visible
- *
+ *		write_seqcount_latch_begin(&latch->seq);
  *		modify(latch->data[0], ...);
- *
- *		smp_wmb();	// Ensure that the data[0] update is visible
- *		latch->seq.sequence++;
- *		smp_wmb();	// Ensure that the seqcount update is visible
- *
+ *		write_seqcount_latch(&latch->seq);
  *		modify(latch->data[1], ...);
+ *		write_seqcount_latch_end(&latch->seq);
  *	}
  *
  * The query will have a form like::
@@ -750,7 +787,7 @@
  *		unsigned seq, idx;
  *
  *		do {
- *			seq = raw_read_seqcount_latch(&latch->seq);
+ *			seq = read_seqcount_latch(&latch->seq);
  *
  *			idx = seq & 0x01;
  *			entry = data_query(latch->data[idx], ...);
@@ -780,11 +817,31 @@
  *	When data is a dynamic data structure; one should use regular RCU
  *	patterns to manage the lifetimes of the objects within.
  */
-static inline void raw_write_seqcount_latch(seqcount_latch_t *s)
+static __always_inline void write_seqcount_latch_begin(seqcount_latch_t *s)
 {
-	smp_wmb();	/* prior stores before incrementing "sequence" */
-	s->seqcount.sequence++;
-	smp_wmb();      /* increment "sequence" before following stores */
+	kcsan_nestable_atomic_begin();
+	raw_write_seqcount_latch(s);
+}
+
+/**
+ * write_seqcount_latch() - redirect latch readers to even copy
+ * @s: Pointer to seqcount_latch_t
+ */
+static __always_inline void write_seqcount_latch(seqcount_latch_t *s)
+{
+	raw_write_seqcount_latch(s);
+}
+
+/**
+ * write_seqcount_latch_end() - end a seqcount_latch_t write section
+ * @s:		Pointer to seqcount_latch_t
+ *
+ * Marks the end of a seqcount_latch_t writer section, after all copies of the
+ * latch-protected data have been updated.
+ */
+static __always_inline void write_seqcount_latch_end(seqcount_latch_t *s)
+{
+	kcsan_nestable_atomic_end();
 }
 
 /*
@@ -837,11 +894,7 @@
  */
 static inline unsigned read_seqbegin(const seqlock_t *sl)
 {
-	unsigned ret = read_seqcount_begin(&sl->seqcount);
-
-	kcsan_atomic_next(0);  /* non-raw usage, assume closing read_seqretry() */
-	kcsan_flat_atomic_begin();
-	return ret;
+	return read_seqcount_begin(&sl->seqcount);
 }
 
 /**
@@ -857,12 +910,6 @@
  */
 static inline unsigned read_seqretry(const seqlock_t *sl, unsigned start)
 {
-	/*
-	 * Assume not nested: read_seqretry() may be called multiple times when
-	 * completing read critical section.
-	 */
-	kcsan_flat_atomic_end();
-
 	return read_seqcount_retry(&sl->seqcount, start);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/serial_8250.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/serial_8250.h
@@ -74,6 +74,7 @@
 struct uart_8250_ops {
 	int		(*setup_irq)(struct uart_8250_port *);
 	void		(*release_irq)(struct uart_8250_port *);
+	void		(*setup_timer)(struct uart_8250_port *);
 };
 
 struct uart_8250_em485 {
@@ -97,7 +98,6 @@
 	struct list_head	list;		/* ports on this IRQ */
 	u32			capabilities;	/* port capabilities */
 	unsigned short		bugs;		/* port bugs */
-	bool			fifo_bug;	/* min RX trigger if enabled */
 	unsigned int		tx_loadsz;	/* transmit fifo load size */
 	unsigned char		acr;
 	unsigned char		fcr;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/serial_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/serial_core.h
@@ -100,7 +100,7 @@
 	__u32	buf_overrun;
 };
 
-typedef unsigned int __bitwise upf_t;
+typedef u64 __bitwise upf_t;
 typedef unsigned int __bitwise upstat_t;
 
 struct uart_port {
@@ -132,6 +132,7 @@
 				      unsigned int old);
 	void			(*handle_break)(struct uart_port *);
 	int			(*rs485_config)(struct uart_port *,
+						struct ktermios *termios,
 						struct serial_rs485 *rs485);
 	int			(*iso7816_config)(struct uart_port *,
 						  struct serial_iso7816 *iso7816);
@@ -207,6 +208,7 @@
 #define UPF_FIXED_PORT		((__force upf_t) (1 << 29))
 #define UPF_DEAD		((__force upf_t) (1 << 30))
 #define UPF_IOREMAP		((__force upf_t) (1 << 31))
+#define UPF_FULL_PROBE		((__force upf_t) (1ULL << 32))
 
 #define __UPF_CHANGE_MASK	0x17fff
 #define UPF_CHANGE_MASK		((__force upf_t) __UPF_CHANGE_MASK)
@@ -232,6 +234,7 @@
 	int			hw_stopped;		/* sw-assisted CTS flow state */
 	unsigned int		mctrl;			/* current modem ctrl settings */
 	unsigned int		timeout;		/* character-based timeout */
+	unsigned int		frame_time;		/* frame timing in ns */
 	unsigned int		type;			/* port type */
 	const struct uart_ops	*ops;
 	unsigned int		custom_divisor;
@@ -253,11 +256,91 @@
 	struct attribute_group	*attr_group;		/* port specific attributes */
 	const struct attribute_group **tty_groups;	/* all attributes (serial core use only) */
 	struct serial_rs485     rs485;
+	const struct serial_rs485	*rs485_supported;	/* Supported mask for serial_rs485 */
 	struct gpio_desc	*rs485_term_gpio;	/* enable RS485 bus termination */
 	struct serial_iso7816   iso7816;
 	void			*private_data;		/* generic platform data pointer */
 };
 
+/**
+ * uart_port_lock - Lock the UART port
+ * @up:		Pointer to UART port structure
+ */
+static inline void uart_port_lock(struct uart_port *up)
+{
+	spin_lock(&up->lock);
+}
+
+/**
+ * uart_port_lock_irq - Lock the UART port and disable interrupts
+ * @up:		Pointer to UART port structure
+ */
+static inline void uart_port_lock_irq(struct uart_port *up)
+{
+	spin_lock_irq(&up->lock);
+}
+
+/**
+ * uart_port_lock_irqsave - Lock the UART port, save and disable interrupts
+ * @up:		Pointer to UART port structure
+ * @flags:	Pointer to interrupt flags storage
+ */
+static inline void uart_port_lock_irqsave(struct uart_port *up, unsigned long *flags)
+{
+	spin_lock_irqsave(&up->lock, *flags);
+}
+
+/**
+ * uart_port_trylock - Try to lock the UART port
+ * @up:		Pointer to UART port structure
+ *
+ * Returns: True if lock was acquired, false otherwise
+ */
+static inline bool uart_port_trylock(struct uart_port *up)
+{
+	return spin_trylock(&up->lock);
+}
+
+/**
+ * uart_port_trylock_irqsave - Try to lock the UART port, save and disable interrupts
+ * @up:		Pointer to UART port structure
+ * @flags:	Pointer to interrupt flags storage
+ *
+ * Returns: True if lock was acquired, false otherwise
+ */
+static inline bool uart_port_trylock_irqsave(struct uart_port *up, unsigned long *flags)
+{
+	return spin_trylock_irqsave(&up->lock, *flags);
+}
+
+/**
+ * uart_port_unlock - Unlock the UART port
+ * @up:		Pointer to UART port structure
+ */
+static inline void uart_port_unlock(struct uart_port *up)
+{
+	spin_unlock(&up->lock);
+}
+
+/**
+ * uart_port_unlock_irq - Unlock the UART port and re-enable interrupts
+ * @up:		Pointer to UART port structure
+ */
+static inline void uart_port_unlock_irq(struct uart_port *up)
+{
+	spin_unlock_irq(&up->lock);
+}
+
+/**
+ * uart_port_unlock_irqrestore - Unlock the UART port, restore interrupts
+ * @up:		Pointer to UART port structure
+ * @flags:	The saved interrupt flags for restore
+ */
+static inline void uart_port_unlock_irqrestore(struct uart_port *up, unsigned long flags)
+{
+	spin_unlock_irqrestore(&up->lock, flags);
+}
+
 static inline int serial_port_in(struct uart_port *up, int offset)
 {
 	return up->serial_in(up, offset);
@@ -300,6 +383,23 @@
 /* number of characters left in xmit buffer before we ask for more */
 #define WAKEUP_CHARS		256
 
+/**
+ * uart_xmit_advance - Advance xmit buffer and account Tx'ed chars
+ * @up: uart_port structure describing the port
+ * @chars: number of characters sent
+ *
+ * This function advances the tail of circular xmit buffer by the number of
+ * @chars transmitted and handles accounting of transmitted bytes (into
+ * @up's icount.tx).
+ */
+static inline void uart_xmit_advance(struct uart_port *up, unsigned int chars)
+{
+	struct circ_buf *xmit = &up->state->xmit;
+
+	xmit->tail = (xmit->tail + chars) & (UART_XMIT_SIZE - 1);
+	up->icount.tx += chars;
+}
+
 struct module;
 struct tty_driver;
 
@@ -388,6 +488,11 @@
 static inline int setup_earlycon(char *buf) { return 0; }
 #endif
 
+static inline bool uart_console_enabled(struct uart_port *port)
+{
+	return uart_console(port) && (port->cons->flags & CON_ENABLED);
+}
+
 struct uart_port *uart_get_console(struct uart_port *ports, int nr,
 				   struct console *c);
 int uart_parse_earlycon(char *p, unsigned char *iotype, resource_size_t *addr,
@@ -458,6 +563,8 @@
 extern void uart_insert_char(struct uart_port *port, unsigned int status,
 		 unsigned int overrun, unsigned int ch, unsigned int flag);
 
+void uart_xchar_out(struct uart_port *uport, int offset);
+
 #ifdef CONFIG_MAGIC_SYSRQ_SERIAL
 #define SYSRQ_TIMEOUT	(HZ * 5)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sh_intc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sh_intc.h
@@ -97,7 +97,10 @@
 	unsigned int nr_subgroups;
 };
 
-#define _INTC_ARRAY(a) a, __same_type(a, NULL) ? 0 : sizeof(a)/sizeof(*a)
+#define _INTC_SIZEOF_OR_ZERO(a) (_Generic(a,                 \
+                                 typeof(NULL):  0,           \
+                                 default:       sizeof(a)))
+#define _INTC_ARRAY(a) a, _INTC_SIZEOF_OR_ZERO(a)/sizeof(*a)
 
 #define INTC_HW_DESC(vectors, groups, mask_regs,	\
 		     prio_regs,	sense_regs, ack_regs)	\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/signal.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/signal.h
@@ -464,6 +464,12 @@
 	unsafe_put_user(t->sas_ss_size, &__uss->ss_size, label); \
 } while (0);
 
+#ifdef CONFIG_DYNAMIC_SIGFRAME
+bool sigaltstack_size_valid(size_t ss_size);
+#else
+static inline bool sigaltstack_size_valid(size_t size) { return true; }
+#endif /* !CONFIG_DYNAMIC_SIGFRAME */
+
 #ifdef CONFIG_PROC_FS
 struct seq_file;
 extern void render_sigset_t(struct seq_file *, const char *, sigset_t *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/signal_types.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/signal_types.h
@@ -70,6 +70,9 @@
 	int sig;
 };
 
+/* Used to kill the race between sigaction and forced signals */
+#define SA_IMMUTABLE		0x00800000
+
 #ifndef __ARCH_UAPI_SA_FLAGS
 #ifdef SA_RESTORER
 #define __ARCH_UAPI_SA_FLAGS	SA_RESTORER
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/siphash.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/siphash.h
@@ -27,9 +27,7 @@
 }
 
 u64 __siphash_aligned(const void *data, size_t len, const siphash_key_t *key);
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u64 __siphash_unaligned(const void *data, size_t len, const siphash_key_t *key);
-#endif
 
 u64 siphash_1u64(const u64 a, const siphash_key_t *key);
 u64 siphash_2u64(const u64 a, const u64 b, const siphash_key_t *key);
@@ -82,10 +80,9 @@
 static inline u64 siphash(const void *data, size_t len,
 			  const siphash_key_t *key)
 {
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
-	if (!IS_ALIGNED((unsigned long)data, SIPHASH_ALIGNMENT))
+	if (IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS) ||
+	    !IS_ALIGNED((unsigned long)data, SIPHASH_ALIGNMENT))
 		return __siphash_unaligned(data, len, key);
-#endif
 	return ___siphash_aligned(data, len, key);
 }
 
@@ -96,10 +93,8 @@
 
 u32 __hsiphash_aligned(const void *data, size_t len,
 		       const hsiphash_key_t *key);
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u32 __hsiphash_unaligned(const void *data, size_t len,
 			 const hsiphash_key_t *key);
-#endif
 
 u32 hsiphash_1u32(const u32 a, const hsiphash_key_t *key);
 u32 hsiphash_2u32(const u32 a, const u32 b, const hsiphash_key_t *key);
@@ -135,11 +130,38 @@
 static inline u32 hsiphash(const void *data, size_t len,
 			   const hsiphash_key_t *key)
 {
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
-	if (!IS_ALIGNED((unsigned long)data, HSIPHASH_ALIGNMENT))
+	if (IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS) ||
+	    !IS_ALIGNED((unsigned long)data, HSIPHASH_ALIGNMENT))
 		return __hsiphash_unaligned(data, len, key);
-#endif
 	return ___hsiphash_aligned(data, len, key);
 }
 
+/*
+ * These macros expose the raw SipHash and HalfSipHash permutations.
+ * Do not use them directly! If you think you have a use for them,
+ * be sure to CC the maintainer of this file explaining why.
+ */
+
+#define SIPHASH_PERMUTATION(a, b, c, d) ( \
+	(a) += (b), (b) = rol64((b), 13), (b) ^= (a), (a) = rol64((a), 32), \
+	(c) += (d), (d) = rol64((d), 16), (d) ^= (c), \
+	(a) += (d), (d) = rol64((d), 21), (d) ^= (a), \
+	(c) += (b), (b) = rol64((b), 17), (b) ^= (c), (c) = rol64((c), 32))
+
+#define SIPHASH_CONST_0 0x736f6d6570736575ULL
+#define SIPHASH_CONST_1 0x646f72616e646f6dULL
+#define SIPHASH_CONST_2 0x6c7967656e657261ULL
+#define SIPHASH_CONST_3 0x7465646279746573ULL
+
+#define HSIPHASH_PERMUTATION(a, b, c, d) ( \
+	(a) += (b), (b) = rol32((b), 5), (b) ^= (a), (a) = rol32((a), 16), \
+	(c) += (d), (d) = rol32((d), 8), (d) ^= (c), \
+	(a) += (d), (d) = rol32((d), 7), (d) ^= (a), \
+	(c) += (b), (b) = rol32((b), 13), (b) ^= (c), (c) = rol32((c), 16))
+
+#define HSIPHASH_CONST_0 0U
+#define HSIPHASH_CONST_1 0U
+#define HSIPHASH_CONST_2 0x6c796765U
+#define HSIPHASH_CONST_3 0x74656462U
+
 #endif /* _LINUX_SIPHASH_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/skbuff.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/skbuff.h
@@ -259,6 +259,7 @@
 	u8			pkt_otherhost:1;
 	u8			in_prerouting:1;
 	u8			bridged_dnat:1;
+	u8			sabotage_in_done:1;
 	__u16			frag_max_size;
 	struct net_device	*physindev;
 
@@ -286,7 +287,10 @@
 struct tc_skb_ext {
 	__u32 chain;
 	__u16 mru;
-	bool post_ct;
+	__u16 zone;
+	u8 post_ct:1;
+	u8 post_ct_snat:1;
+	u8 post_ct_dnat:1;
 };
 #endif
 
@@ -301,6 +305,41 @@
 
 struct sk_buff;
 
+/* The reason of skb drop, which is used in kfree_skb_reason().
+ * en...maybe they should be splited by group?
+ *
+ * Each item here should also be in 'TRACE_SKB_DROP_REASON', which is
+ * used to translate the reason to string.
+ */
+enum skb_drop_reason {
+	SKB_DROP_REASON_NOT_SPECIFIED,	/* drop reason is not specified */
+	SKB_DROP_REASON_NO_SOCKET,	/* socket not found */
+	SKB_DROP_REASON_PKT_TOO_SMALL,	/* packet size is too small */
+	SKB_DROP_REASON_TCP_CSUM,	/* TCP checksum error */
+	SKB_DROP_REASON_SOCKET_FILTER,	/* dropped by socket filter */
+	SKB_DROP_REASON_UDP_CSUM,	/* UDP checksum error */
+	SKB_DROP_REASON_NETFILTER_DROP,	/* dropped by netfilter */
+	SKB_DROP_REASON_OTHERHOST,	/* packet don't belong to current
+					 * host (interface is in promisc
+					 * mode)
+					 */
+	SKB_DROP_REASON_IP_CSUM,	/* IP checksum error */
+	SKB_DROP_REASON_IP_INHDR,	/* there is something wrong with
+					 * IP header (see
+					 * IPSTATS_MIB_INHDRERRORS)
+					 */
+	SKB_DROP_REASON_IP_RPFILTER,	/* IP rpfilter validate failed.
+					 * see the document for rp_filter
+					 * in ip-sysctl.rst for more
+					 * information
+					 */
+	SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST, /* destination address of L2
+						  * is multicast, but L3 is
+						  * unicast.
+						  */
+	SKB_DROP_REASON_MAX,
+};
+
 /* To allow 64K frame to be packed as single skb without frag_list we
  * require 64K/PAGE_SIZE pages plus 1 additional page to allow for
  * buffers which do not start on a page boundary.
@@ -621,8 +660,6 @@
  *	@rbnode: RB tree node, alternative to next/prev for netem/tcp
  *	@list: queue head
  *	@sk: Socket we are owned by
- *	@ip_defrag_offset: (aka @sk) alternate use of @sk, used in
- *		fragmentation management
  *	@dev: Device we arrived on/are leaving by
  *	@dev_scratch: (aka @dev) alternate use of @dev when @dev would be %NULL
  *	@cb: Control buffer. Free for use by every layer. Put private vars here
@@ -687,6 +724,7 @@
  *	@csum_level: indicates the number of consecutive checksums found in
  *		the packet minus one that have been verified as
  *		CHECKSUM_UNNECESSARY (max 3)
+ *	@scm_io_uring: SKB holds io_uring registered files
  *	@dst_pending_confirm: need to confirm neighbour
  *	@decrypted: Decrypted SKB
  *	@slow_gro: state present at GRO time, slower prepare step required
@@ -738,10 +776,7 @@
 		struct list_head	list;
 	};
 
-	union {
-		struct sock		*sk;
-		int			ip_defrag_offset;
-	};
+	struct sock		*sk;
 
 	union {
 		ktime_t		tstamp;
@@ -872,6 +907,7 @@
 	__u8			decrypted:1;
 #endif
 	__u8			slow_gro:1;
+	__u8			scm_io_uring:1;
 
 #ifdef CONFIG_NET_SCHED
 	__u16			tc_index;	/* traffic control index */
@@ -1071,8 +1107,18 @@
 	return true;
 }
 
+void kfree_skb_reason(struct sk_buff *skb, enum skb_drop_reason reason);
+
+/**
+ *	kfree_skb - free an sk_buff with 'NOT_SPECIFIED' reason
+ *	@skb: buffer to free
+ */
+static inline void kfree_skb(struct sk_buff *skb)
+{
+	kfree_skb_reason(skb, SKB_DROP_REASON_NOT_SPECIFIED);
+}
+
 void skb_release_head_state(struct sk_buff *skb);
-void kfree_skb(struct sk_buff *skb);
 void kfree_skb_list(struct sk_buff *segs);
 void skb_dump(const char *level, const struct sk_buff *skb, bool full_pkt);
 void skb_tx_error(struct sk_buff *skb);
@@ -1370,7 +1416,7 @@
 		    struct flow_dissector *flow_dissector,
 		    void *target_container,
 		    u16 *ctinfo_map, size_t mapsize,
-		    bool post_ct);
+		    bool post_ct, u16 zone);
 void
 skb_flow_dissect_tunnel_info(const struct sk_buff *skb,
 			     struct flow_dissector *flow_dissector,
@@ -1433,6 +1479,11 @@
 {
 	return skb->end;
 }
+
+static inline void skb_set_end_offset(struct sk_buff *skb, unsigned int offset)
+{
+	skb->end = offset;
+}
 #else
 static inline unsigned char *skb_end_pointer(const struct sk_buff *skb)
 {
@@ -1443,6 +1494,11 @@
 {
 	return skb->end - skb->head;
 }
+
+static inline void skb_set_end_offset(struct sk_buff *skb, unsigned int offset)
+{
+	skb->end = skb->head + offset;
+}
 #endif
 
 /* Internal */
@@ -1671,6 +1727,22 @@
 	return 0;
 }
 
+/* This variant of skb_unclone() makes sure skb->truesize
+ * and skb_end_offset() are not changed, whenever a new skb->head is needed.
+ *
+ * Indeed there is no guarantee that ksize(kmalloc(X)) == ksize(kmalloc(X))
+ * when various debugging features are in place.
+ */
+int __skb_unclone_keeptruesize(struct sk_buff *skb, gfp_t pri);
+static inline int skb_unclone_keeptruesize(struct sk_buff *skb, gfp_t pri)
+{
+	might_sleep_if(gfpflags_allow_blocking(pri));
+
+	if (skb_cloned(skb))
+		return __skb_unclone_keeptruesize(skb, pri);
+	return 0;
+}
+
 /**
  *	skb_header_cloned - is the header a clone
  *	@skb: buffer to check
@@ -2158,6 +2230,22 @@
 	return skb_headlen(skb) + __skb_pagelen(skb);
 }
 
+static inline void __skb_fill_page_desc_noacc(struct skb_shared_info *shinfo,
+					      int i, struct page *page,
+					      int off, int size)
+{
+	skb_frag_t *frag = &shinfo->frags[i];
+
+	/*
+	 * Propagate page pfmemalloc to the skb if we can. The problem is
+	 * that not all callers have unique ownership of the page but rely
+	 * on page_is_pfmemalloc doing the right thing(tm).
+	 */
+	frag->bv_page		  = page;
+	frag->bv_offset		  = off;
+	skb_frag_size_set(frag, size);
+}
+
 /**
  * __skb_fill_page_desc - initialise a paged fragment in an skb
  * @skb: buffer containing fragment to be initialised
@@ -2174,17 +2262,7 @@
 static inline void __skb_fill_page_desc(struct sk_buff *skb, int i,
 					struct page *page, int off, int size)
 {
-	skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
-
-	/*
-	 * Propagate page pfmemalloc to the skb if we can. The problem is
-	 * that not all callers have unique ownership of the page but rely
-	 * on page_is_pfmemalloc doing the right thing(tm).
-	 */
-	frag->bv_page		  = page;
-	frag->bv_offset		  = off;
-	skb_frag_size_set(frag, size);
-
+	__skb_fill_page_desc_noacc(skb_shinfo(skb), i, page, off, size);
 	page = compound_head(page);
 	if (page_is_pfmemalloc(page))
 		skb->pfmemalloc	= true;
@@ -2211,6 +2289,27 @@
 	skb_shinfo(skb)->nr_frags = i + 1;
 }
 
+/**
+ * skb_fill_page_desc_noacc - initialise a paged fragment in an skb
+ * @skb: buffer containing fragment to be initialised
+ * @i: paged fragment index to initialise
+ * @page: the page to use for this fragment
+ * @off: the offset to the data with @page
+ * @size: the length of the data
+ *
+ * Variant of skb_fill_page_desc() which does not deal with
+ * pfmemalloc, if page is not owned by us.
+ */
+static inline void skb_fill_page_desc_noacc(struct sk_buff *skb, int i,
+					    struct page *page, int off,
+					    int size)
+{
+	struct skb_shared_info *shinfo = skb_shinfo(skb);
+
+	__skb_fill_page_desc_noacc(shinfo, i, page, off, size);
+	shinfo->nr_frags = i + 1;
+}
+
 void skb_add_rx_frag(struct sk_buff *skb, int i, struct page *page, int off,
 		     int size, unsigned int truesize);
 
@@ -2254,6 +2353,14 @@
 
 #endif /* NET_SKBUFF_DATA_USES_OFFSET */
 
+static inline void skb_assert_len(struct sk_buff *skb)
+{
+#ifdef CONFIG_DEBUG_NET
+	if (WARN_ONCE(!skb->len, "%s\n", __func__))
+		DO_ONCE_LITE(skb_dump, KERN_ERR, skb, false);
+#endif /* CONFIG_DEBUG_NET */
+}
+
 /*
  *	Add data to an sk_buff
  */
@@ -2335,6 +2442,8 @@
 	return unlikely(len > skb->len) ? NULL : __skb_pull(skb, len);
 }
 
+void *skb_pull_data(struct sk_buff *skb, size_t len);
+
 void *__pskb_pull_tail(struct sk_buff *skb, int delta);
 
 static inline void *__pskb_pull(struct sk_buff *skb, unsigned int len)
@@ -2623,6 +2732,21 @@
 	}
 }
 
+/* Move the full mac header up to current network_header.
+ * Leaves skb->data pointing at offset skb->mac_len into the mac_header.
+ * Must be provided the complete mac header length.
+ */
+static inline void skb_mac_header_rebuild_full(struct sk_buff *skb, u32 full_mac_len)
+{
+	if (skb_mac_header_was_set(skb)) {
+		const unsigned char *old_mac = skb_mac_header(skb);
+
+		skb_set_mac_header(skb, -full_mac_len);
+		memmove(skb_mac_header(skb), old_mac, full_mac_len);
+		__skb_push(skb, full_mac_len - skb->mac_len);
+	}
+}
+
 static inline int skb_checksum_start_offset(const struct sk_buff *skb)
 {
 	return skb->csum_start - skb_headroom(skb);
@@ -4350,7 +4474,7 @@
 
 static inline void nf_reset_trace(struct sk_buff *skb)
 {
-#if IS_ENABLED(CONFIG_NETFILTER_XT_TARGET_TRACE) || defined(CONFIG_NF_TABLES)
+#if IS_ENABLED(CONFIG_NETFILTER_XT_TARGET_TRACE) || IS_ENABLED(CONFIG_NF_TABLES)
 	skb->nf_trace = 0;
 #endif
 }
@@ -4370,7 +4494,7 @@
 	dst->_nfct = src->_nfct;
 	nf_conntrack_get(skb_nfct(src));
 #endif
-#if IS_ENABLED(CONFIG_NETFILTER_XT_TARGET_TRACE) || defined(CONFIG_NF_TABLES)
+#if IS_ENABLED(CONFIG_NETFILTER_XT_TARGET_TRACE) || IS_ENABLED(CONFIG_NF_TABLES)
 	if (copy)
 		dst->nf_trace = src->nf_trace;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/skmsg.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/skmsg.h
@@ -63,6 +63,7 @@
 
 enum sk_psock_state_bits {
 	SK_PSOCK_TX_ENABLED,
+	SK_PSOCK_RX_STRP_ENABLED,
 };
 
 struct sk_psock_link {
@@ -72,7 +73,6 @@
 };
 
 struct sk_psock_work_state {
-	struct sk_buff			*skb;
 	u32				len;
 	u32				off;
 };
@@ -83,6 +83,7 @@
 	u32				apply_bytes;
 	u32				cork_bytes;
 	u32				eval;
+	bool				redir_ingress; /* undefined if sk_redir is null */
 	struct sk_msg			*cork;
 	struct sk_psock_progs		progs;
 #if IS_ENABLED(CONFIG_BPF_STREAM_PARSER)
@@ -96,6 +97,7 @@
 	spinlock_t			link_lock;
 	refcount_t			refcnt;
 	void (*saved_unhash)(struct sock *sk);
+	void (*saved_destroy)(struct sock *sk);
 	void (*saved_close)(struct sock *sk, long timeout);
 	void (*saved_write_space)(struct sock *sk);
 	void (*saved_data_ready)(struct sock *sk);
@@ -104,7 +106,7 @@
 	struct proto			*sk_proto;
 	struct mutex			work_mutex;
 	struct sk_psock_work_state	work_state;
-	struct work_struct		work;
+	struct delayed_work		work;
 	struct rcu_work			rwork;
 };
 
@@ -283,7 +285,8 @@
 
 static inline struct sk_psock *sk_psock(const struct sock *sk)
 {
-	return rcu_dereference_sk_user_data(sk);
+	return __rcu_dereference_sk_user_data_with_flags(sk,
+							 SK_USER_DATA_PSOCK);
 }
 
 static inline void sk_psock_set_state(struct sk_psock *psock,
@@ -310,22 +313,22 @@
 	kfree_skb(skb);
 }
 
-static inline void drop_sk_msg(struct sk_psock *psock, struct sk_msg *msg)
-{
-	if (msg->skb)
-		sock_drop(psock->sk, msg->skb);
-	kfree(msg);
-}
-
-static inline void sk_psock_queue_msg(struct sk_psock *psock,
+static inline bool sk_psock_queue_msg(struct sk_psock *psock,
 				      struct sk_msg *msg)
 {
+	bool ret;
+
 	spin_lock_bh(&psock->ingress_lock);
-	if (sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED))
+	if (sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED)) {
 		list_add_tail(&msg->list, &psock->ingress_msg);
-	else
-		drop_sk_msg(psock, msg);
+		ret = true;
+	} else {
+		sk_msg_free(psock->sk, msg);
+		kfree(msg);
+		ret = false;
+	}
 	spin_unlock_bh(&psock->ingress_lock);
+	return ret;
 }
 
 static inline struct sk_msg *sk_psock_dequeue_msg(struct sk_psock *psock)
@@ -385,7 +388,7 @@
 }
 
 struct sk_psock *sk_psock_init(struct sock *sk, int node);
-void sk_psock_stop(struct sk_psock *psock, bool wait);
+void sk_psock_stop(struct sk_psock *psock);
 
 #if IS_ENABLED(CONFIG_BPF_STREAM_PARSER)
 int sk_psock_init_strp(struct sock *sk, struct sk_psock *psock);
@@ -463,10 +466,12 @@
 
 static inline void sk_psock_data_ready(struct sock *sk, struct sk_psock *psock)
 {
+	read_lock_bh(&sk->sk_callback_lock);
 	if (psock->saved_data_ready)
 		psock->saved_data_ready(sk);
 	else
 		sk->sk_data_ready(sk);
+	read_unlock_bh(&sk->sk_callback_lock);
 }
 
 static inline void psock_set_prog(struct bpf_prog **pprog,
@@ -509,8 +514,22 @@
 
 #if IS_ENABLED(CONFIG_NET_SOCK_MSG)
 
-/* We only have one bit so far. */
-#define BPF_F_PTR_MASK ~(BPF_F_INGRESS)
+#define BPF_F_STRPARSER	(1UL << 1)
+
+/* We only have two bits so far. */
+#define BPF_F_PTR_MASK ~(BPF_F_INGRESS | BPF_F_STRPARSER)
+
+static inline bool skb_bpf_strparser(const struct sk_buff *skb)
+{
+	unsigned long sk_redir = skb->_sk_redir;
+
+	return sk_redir & BPF_F_STRPARSER;
+}
+
+static inline void skb_bpf_set_strparser(struct sk_buff *skb)
+{
+	skb->_sk_redir |= BPF_F_STRPARSER;
+}
 
 static inline bool skb_bpf_ingress(const struct sk_buff *skb)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/slab.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/slab.h
@@ -152,8 +152,8 @@
 			slab_flags_t flags,
 			unsigned int useroffset, unsigned int usersize,
 			void (*ctor)(void *));
-void kmem_cache_destroy(struct kmem_cache *);
-int kmem_cache_shrink(struct kmem_cache *);
+void kmem_cache_destroy(struct kmem_cache *s);
+int kmem_cache_shrink(struct kmem_cache *s);
 
 /*
  * Please use this macro to create slab caches. Simply specify the
@@ -181,11 +181,25 @@
 /*
  * Common kmalloc functions provided by all allocators
  */
-void * __must_check krealloc(const void *, size_t, gfp_t);
-void kfree(const void *);
-void kfree_sensitive(const void *);
-size_t __ksize(const void *);
-size_t ksize(const void *);
+void * __must_check krealloc(const void *objp, size_t new_size, gfp_t flags);
+void kfree(const void *objp);
+void kfree_sensitive(const void *objp);
+size_t __ksize(const void *objp);
+
+/**
+ * ksize - Report actual allocation size of associated object
+ *
+ * @objp: Pointer returned from a prior kmalloc()-family allocation.
+ *
+ * This should not be used for writing beyond the originally requested
+ * allocation size. Either use krealloc() or round up the allocation size
+ * with kmalloc_size_roundup() prior to allocation. If this is used to
+ * access beyond the originally requested allocation size, UBSAN_BOUNDS
+ * and/or FORTIFY_SOURCE may trip, since they only know about the
+ * originally allocated size via the __alloc_size attribute.
+ */
+size_t ksize(const void *objp);
+
 #ifdef CONFIG_PRINTK
 bool kmem_valid_obj(void *object);
 void kmem_dump_obj(void *object);
@@ -426,8 +440,8 @@
 #endif /* !CONFIG_SLOB */
 
 void *__kmalloc(size_t size, gfp_t flags) __assume_kmalloc_alignment __malloc;
-void *kmem_cache_alloc(struct kmem_cache *, gfp_t flags) __assume_slab_alignment __malloc;
-void kmem_cache_free(struct kmem_cache *, void *);
+void *kmem_cache_alloc(struct kmem_cache *s, gfp_t flags) __assume_slab_alignment __malloc;
+void kmem_cache_free(struct kmem_cache *s, void *objp);
 
 /*
  * Bulk allocation and freeing operations. These are accelerated in an
@@ -436,8 +450,8 @@
  *
  * Note that interrupts must be enabled when calling these functions.
  */
-void kmem_cache_free_bulk(struct kmem_cache *, size_t, void **);
-int kmem_cache_alloc_bulk(struct kmem_cache *, gfp_t, size_t, void **);
+void kmem_cache_free_bulk(struct kmem_cache *s, size_t size, void **p);
+int kmem_cache_alloc_bulk(struct kmem_cache *s, gfp_t flags, size_t size, void **p);
 
 /*
  * Caller must not use kfree_bulk() on memory not originally allocated
@@ -450,7 +464,8 @@
 
 #ifdef CONFIG_NUMA
 void *__kmalloc_node(size_t size, gfp_t flags, int node) __assume_kmalloc_alignment __malloc;
-void *kmem_cache_alloc_node(struct kmem_cache *, gfp_t flags, int node) __assume_slab_alignment __malloc;
+void *kmem_cache_alloc_node(struct kmem_cache *s, gfp_t flags, int node) __assume_slab_alignment
+									 __malloc;
 #else
 static __always_inline void *__kmalloc_node(size_t size, gfp_t flags, int node)
 {
@@ -464,25 +479,24 @@
 #endif
 
 #ifdef CONFIG_TRACING
-extern void *kmem_cache_alloc_trace(struct kmem_cache *, gfp_t, size_t) __assume_slab_alignment __malloc;
+extern void *kmem_cache_alloc_trace(struct kmem_cache *s, gfp_t flags, size_t size)
+				   __assume_slab_alignment __malloc;
 
 #ifdef CONFIG_NUMA
-extern void *kmem_cache_alloc_node_trace(struct kmem_cache *s,
-					   gfp_t gfpflags,
-					   int node, size_t size) __assume_slab_alignment __malloc;
+extern void *kmem_cache_alloc_node_trace(struct kmem_cache *s, gfp_t gfpflags,
+					 int node, size_t size) __assume_slab_alignment __malloc;
 #else
-static __always_inline void *
-kmem_cache_alloc_node_trace(struct kmem_cache *s,
-			      gfp_t gfpflags,
-			      int node, size_t size)
+static __always_inline void *kmem_cache_alloc_node_trace(struct kmem_cache *s,
+							 gfp_t gfpflags, int node,
+							 size_t size)
 {
 	return kmem_cache_alloc_trace(s, gfpflags, size);
 }
 #endif /* CONFIG_NUMA */
 
 #else /* CONFIG_TRACING */
-static __always_inline void *kmem_cache_alloc_trace(struct kmem_cache *s,
-		gfp_t flags, size_t size)
+static __always_inline void *kmem_cache_alloc_trace(struct kmem_cache *s, gfp_t flags,
+						    size_t size)
 {
 	void *ret = kmem_cache_alloc(s, flags);
 
@@ -490,10 +504,8 @@
 	return ret;
 }
 
-static __always_inline void *
-kmem_cache_alloc_node_trace(struct kmem_cache *s,
-			      gfp_t gfpflags,
-			      int node, size_t size)
+static __always_inline void *kmem_cache_alloc_node_trace(struct kmem_cache *s, gfp_t gfpflags,
+							 int node, size_t size)
 {
 	void *ret = kmem_cache_alloc_node(s, gfpflags, node);
 
@@ -502,13 +514,14 @@
 }
 #endif /* CONFIG_TRACING */
 
-extern void *kmalloc_order(size_t size, gfp_t flags, unsigned int order) __assume_page_alignment __malloc;
+extern void *kmalloc_order(size_t size, gfp_t flags, unsigned int order) __assume_page_alignment
+									 __malloc;
 
 #ifdef CONFIG_TRACING
-extern void *kmalloc_order_trace(size_t size, gfp_t flags, unsigned int order) __assume_page_alignment __malloc;
+extern void *kmalloc_order_trace(size_t size, gfp_t flags, unsigned int order)
+				__assume_page_alignment __malloc;
 #else
-static __always_inline void *
-kmalloc_order_trace(size_t size, gfp_t flags, unsigned int order)
+static __always_inline void *kmalloc_order_trace(size_t size, gfp_t flags, unsigned int order)
 {
 	return kmalloc_order(size, flags, order);
 }
@@ -638,8 +651,8 @@
  * @new_size: new size of a single member of the array
  * @flags: the type of memory to allocate (see kmalloc)
  */
-static __must_check inline void *
-krealloc_array(void *p, size_t new_n, size_t new_size, gfp_t flags)
+static inline void * __must_check krealloc_array(void *p, size_t new_n, size_t new_size,
+						 gfp_t flags)
 {
 	size_t bytes;
 
@@ -668,7 +681,7 @@
  * allocator where we care about the real place the memory allocation
  * request comes from.
  */
-extern void *__kmalloc_track_caller(size_t, gfp_t, unsigned long);
+extern void *__kmalloc_track_caller(size_t size, gfp_t flags, unsigned long caller);
 #define kmalloc_track_caller(size, flags) \
 	__kmalloc_track_caller(size, flags, _RET_IP_)
 
@@ -691,7 +704,8 @@
 
 
 #ifdef CONFIG_NUMA
-extern void *__kmalloc_node_track_caller(size_t, gfp_t, int, unsigned long);
+extern void *__kmalloc_node_track_caller(size_t size, gfp_t flags, int node,
+					 unsigned long caller);
 #define kmalloc_node_track_caller(size, flags, node) \
 	__kmalloc_node_track_caller(size, flags, node, \
 			_RET_IP_)
@@ -733,6 +747,23 @@
 }
 
 unsigned int kmem_cache_size(struct kmem_cache *s);
+
+/**
+ * kmalloc_size_roundup - Report allocation bucket size for the given size
+ *
+ * @size: Number of bytes to round up from.
+ *
+ * This returns the number of bytes that would be available in a kmalloc()
+ * allocation of @size bytes. For example, a 126 byte request would be
+ * rounded up to the next sized kmalloc bucket, 128 bytes. (This is strictly
+ * for the general-purpose kmalloc()-based allocations, and is not for the
+ * pre-sized kmem_cache_alloc()-based allocations.)
+ *
+ * Use this to kmalloc() the full bucket size ahead of time instead of using
+ * ksize() to query the size after an allocation.
+ */
+size_t kmalloc_size_roundup(size_t size);
+
 void __init kmem_cache_init_late(void);
 
 #if defined(CONFIG_SMP) && defined(CONFIG_SLAB)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/soc/marvell/octeontx2/asm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/soc/marvell/octeontx2/asm.h
@@ -5,6 +5,7 @@
 #ifndef __SOC_OTX2_ASM_H
 #define __SOC_OTX2_ASM_H
 
+#include <linux/types.h>
 #if defined(CONFIG_ARM64)
 /*
  * otx2_lmt_flush is used for LMT store operation.
@@ -34,9 +35,23 @@
 			 : [rf] "+r"(val)		\
 			 : [rs] "r"(addr));		\
 })
+
+static inline u64 otx2_atomic64_fetch_add(u64 incr, u64 *ptr)
+{
+	u64 result;
+
+	asm volatile (".cpu  generic+lse\n"
+		      "ldadda %x[i], %x[r], [%[b]]"
+		      : [r] "=r" (result), "+m" (*ptr)
+		      : [i] "r" (incr), [b] "r" (ptr)
+		      : "memory");
+	return result;
+}
+
 #else
 #define otx2_lmt_flush(ioaddr)          ({ 0; })
 #define cn10k_lmt_flush(val, addr)	({ addr = val; })
+#define otx2_atomic64_fetch_add(incr, ptr)	({ incr; })
 #endif
 
 #endif /* __SOC_OTX2_ASM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/soc/qcom/apr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/soc/qcom/apr.h
@@ -79,6 +79,15 @@
 #define APR_SVC_MAJOR_VERSION(v)	((v >> 16) & 0xFF)
 #define APR_SVC_MINOR_VERSION(v)	(v & 0xFF)
 
+struct packet_router;
+struct pkt_router_svc {
+	struct device *dev;
+	struct packet_router *pr;
+	spinlock_t lock;
+	int id;
+	void *priv;
+};
+
 struct apr_device {
 	struct device	dev;
 	uint16_t	svc_id;
@@ -86,11 +95,12 @@
 	uint32_t	version;
 	char name[APR_NAME_SIZE];
 	const char *service_path;
-	spinlock_t	lock;
+	struct pkt_router_svc svc;
 	struct list_head node;
 };
 
 #define to_apr_device(d) container_of(d, struct apr_device, dev)
+#define svc_to_apr_device(d) container_of(d, struct apr_device, svc)
 
 struct apr_driver {
 	int	(*probe)(struct apr_device *sl);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/soc/qcom/qcom_aoss.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/soc/qcom/qcom_aoss.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef __QCOM_AOSS_H__
+#define __QCOM_AOSS_H__
+
+#include <linux/err.h>
+#include <linux/device.h>
+
+struct qmp;
+
+#if IS_ENABLED(CONFIG_QCOM_AOSS_QMP)
+
+int qmp_send(struct qmp *qmp, const void *data, size_t len);
+struct qmp *qmp_get(struct device *dev);
+void qmp_put(struct qmp *qmp);
+
+#else
+
+static inline int qmp_send(struct qmp *qmp, const void *data, size_t len)
+{
+	return -ENODEV;
+}
+
+static inline struct qmp *qmp_get(struct device *dev)
+{
+	return ERR_PTR(-ENODEV);
+}
+
+static inline void qmp_put(struct qmp *qmp)
+{
+}
+
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/soc/ti/ti_sci_protocol.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/soc/ti/ti_sci_protocol.h
@@ -645,7 +645,7 @@
 
 static inline struct ti_sci_resource *
 devm_ti_sci_get_resource(const struct ti_sci_handle *handle, struct device *dev,
-			 u32 dev_id, u32 sub_type);
+			 u32 dev_id, u32 sub_type)
 {
 	return ERR_PTR(-EINVAL);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/socket.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/socket.h
@@ -31,7 +31,10 @@
 
 struct sockaddr {
 	sa_family_t	sa_family;	/* address family, AF_xxx	*/
-	char		sa_data[14];	/* 14 bytes of protocol address	*/
+	union {
+		char sa_data_min[14];		/* Minimum 14 bytes of protocol address	*/
+		DECLARE_FLEX_ARRAY(char, sa_data);
+	};
 };
 
 struct linger {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sockptr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sockptr.h
@@ -64,6 +64,11 @@
 	return 0;
 }
 
+static inline int copy_to_sockptr(sockptr_t dst, const void *src, size_t size)
+{
+	return copy_to_sockptr_offset(dst, 0, src, size);
+}
+
 static inline void *memdup_sockptr(sockptr_t src, size_t len)
 {
 	void *p = kmalloc_track_caller(len, GFP_USER | __GFP_NOWARN);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/soundwire/sdw.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/soundwire/sdw.h
@@ -646,9 +646,6 @@
  * @dev_num: Current Device Number, values can be 0 or dev_num_sticky
  * @dev_num_sticky: one-time static Device Number assigned by Bus
  * @probed: boolean tracking driver state
- * @probe_complete: completion utility to control potential races
- * on startup between driver probe/initialization and SoundWire
- * Slave state changes/implementation-defined interrupts
  * @enumeration_complete: completion utility to control potential races
  * on startup between device enumeration and read/write access to the
  * Slave device
@@ -663,6 +660,7 @@
  * for a Slave happens for the first time after enumeration
  * @is_mockup_device: status flag used to squelch errors in the command/control
  * protocol for SoundWire mockup devices
+ * @sdw_dev_lock: mutex used to protect callbacks/remove races
  */
 struct sdw_slave {
 	struct sdw_slave_id id;
@@ -680,12 +678,12 @@
 	u16 dev_num;
 	u16 dev_num_sticky;
 	bool probed;
-	struct completion probe_complete;
 	struct completion enumeration_complete;
 	struct completion initialization_complete;
 	u32 unattach_request;
 	bool first_interrupt_done;
 	bool is_mockup_device;
+	struct mutex sdw_dev_lock; /* protect callbacks/remove races */
 };
 
 #define dev_to_sdw_dev(_dev) container_of(_dev, struct sdw_slave, dev)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/spi/spi-mem.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/spi/spi-mem.h
@@ -55,6 +55,8 @@
 
 #define SPI_MEM_OP_NO_DATA	{ }
 
+#define SPI_MEM_DEV_MAX_ID_LEN		6
+
 /**
  * enum spi_mem_data_dir - describes the direction of a SPI memory data
  *			   transfer from the controller perspective
@@ -195,6 +197,9 @@
 	struct spi_device *spi;
 	void *drvpriv;
 	const char *name;
+	u8 device_id[SPI_MEM_DEV_MAX_ID_LEN];
+	struct delayed_work	complete_work;
+	struct completion	request_completion;
 };
 
 /**
@@ -356,6 +361,7 @@
 
 int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op);
 
+bool update_stripe(const struct spi_mem_op *op);
 bool spi_mem_supports_op(struct spi_mem *mem,
 			 const struct spi_mem_op *op);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/spi/spi.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/spi/spi.h
@@ -17,6 +17,7 @@
 #include <linux/ptp_clock_kernel.h>
 
 #include <uapi/linux/spi/spi.h>
+#include <linux/acpi.h>
 
 struct dma_chan;
 struct software_node;
@@ -147,6 +148,7 @@
  *	not using a GPIO line)
  * @word_delay: delay to be inserted between consecutive
  *	words of a transfer
+ * @multi_die: Flash device with multiple dies.
  * @cs_setup: delay to be introduced by the controller after CS is asserted
  * @cs_hold: delay to be introduced by the controller before CS is deasserted
  * @cs_inactive: delay to be introduced by the controller after CS is
@@ -192,6 +194,7 @@
 	int			cs_gpio;	/* LEGACY: chip select gpio */
 	struct gpio_desc	*cs_gpiod;	/* chip select gpio desc */
 	struct spi_delay	word_delay; /* inter-word delay */
+	bool			multi_die;	/* flash with multiple dies*/
 	/* CS delays */
 	struct spi_delay	cs_setup;
 	struct spi_delay	cs_hold;
@@ -514,7 +517,20 @@
 #define SPI_CONTROLLER_MUST_TX		BIT(4)	/* requires tx */
 
 #define SPI_MASTER_GPIO_SS		BIT(5)	/* GPIO CS must select slave */
-
+	/*
+	 * Controller may support data stripe feature when more than one
+	 * chips are present.
+	 * Setting data stripe will send data in following manner:
+	 * -> even bytes i.e. 0, 2, 4,... are transmitted on lower data bus
+	 * -> odd bytes i.e. 1, 3, 5,.. are transmitted on upper data bus
+	 */
+#define SPI_MASTER_DATA_STRIPE BIT(7)		/* support data stripe */
+	/*
+	 * Controller may support asserting more than one chip select at once.
+	 * This flag will enable that feature.
+	 */
+#define SPI_MASTER_BOTH_CS	BIT(8)		/* assert both chip selects */
+#define SPI_MASTER_U_PAGE	BIT(9)		/* select upper flash */
 	/* flag indicating if the allocation of this struct is devres-managed */
 	bool			devm_allocated;
 
@@ -764,6 +780,12 @@
 extern void spi_unregister_controller(struct spi_controller *ctlr);
 
 extern struct spi_controller *spi_busnum_to_master(u16 busnum);
+#if IS_ENABLED(CONFIG_ACPI)
+extern struct spi_device *acpi_spi_device_alloc(struct spi_controller *ctlr,
+						struct acpi_device *adev,
+						int index);
+int acpi_spi_count_resources(struct acpi_device *adev);
+#endif
 
 /*
  * SPI resource management while processing a SPI message
@@ -829,6 +851,7 @@
  * @len: size of rx and tx buffers (in bytes)
  * @speed_hz: Select a speed other than the device default for this
  *      transfer. If 0 the default (from @spi_device) is used.
+ * @dummy: number of dummy cycles.
  * @bits_per_word: select a bits_per_word other than the device default
  *      for this transfer. If 0 the default (from @spi_device) is used.
  * @dummy_data: indicates transfer is dummy bytes transfer.
@@ -846,6 +869,7 @@
  * @transfer_list: transfers are sequenced through @spi_message.transfers
  * @tx_sg: Scatterlist for transmit, currently not for client use
  * @rx_sg: Scatterlist for receive, currently not for client use
+ * @stripe: true-> enable stripe, false-> disable stripe.
  * @ptp_sts_word_pre: The word (subject to bits_per_word semantics) offset
  *	within @tx_buf for which the SPI device is requesting that the time
  *	snapshot for this transfer begins. Upon completing the SPI transfer,
@@ -953,6 +977,8 @@
 	struct spi_delay	cs_change_delay;
 	struct spi_delay	word_delay;
 	u32		speed_hz;
+	u32		dummy;
+	bool		stripe;
 
 	u32		effective_speed_hz;
 
@@ -1499,6 +1525,9 @@
 extern const struct spi_device_id *
 spi_get_device_id(const struct spi_device *sdev);
 
+extern const void *
+spi_get_device_match_data(const struct spi_device *sdev);
+
 static inline bool
 spi_transfer_is_last(struct spi_controller *ctlr, struct spi_transfer *xfer)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/splice.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/splice.h
@@ -93,4 +93,10 @@
 
 extern const struct pipe_buf_operations page_cache_pipe_buf_ops;
 extern const struct pipe_buf_operations default_pipe_buf_ops;
+
+extern long do_splice_from(struct pipe_inode_info *pipe, struct file *out,
+			   loff_t *ppos, size_t len, unsigned int flags);
+extern long do_splice_to(struct file *in, loff_t *ppos,
+			 struct pipe_inode_info *pipe, size_t len,
+			 unsigned int flags);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/stackdepot.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/stackdepot.h
@@ -19,8 +19,6 @@
 unsigned int stack_depot_fetch(depot_stack_handle_t handle,
 			       unsigned long **entries);
 
-unsigned int filter_irq_stacks(unsigned long *entries, unsigned int nr_entries);
-
 #ifdef CONFIG_STACKDEPOT
 int stack_depot_init(void);
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/stacktrace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/stacktrace.h
@@ -21,6 +21,7 @@
 unsigned int stack_trace_save_regs(struct pt_regs *regs, unsigned long *store,
 				   unsigned int size, unsigned int skipnr);
 unsigned int stack_trace_save_user(unsigned long *store, unsigned int size);
+unsigned int filter_irq_stacks(unsigned long *entries, unsigned int nr_entries);
 
 /* Internal interfaces. Do not use in generic code */
 #ifdef CONFIG_ARCH_STACKWALK
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/static_call.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/static_call.h
@@ -160,6 +160,8 @@
 
 #ifdef CONFIG_HAVE_STATIC_CALL_INLINE
 
+extern bool static_call_initialized;
+
 extern int __init static_call_init(void);
 
 struct static_call_mod {
@@ -215,6 +217,8 @@
 
 #elif defined(CONFIG_HAVE_STATIC_CALL)
 
+#define static_call_initialized 0
+
 static inline int static_call_init(void) { return 0; }
 
 #define __DEFINE_STATIC_CALL(name, _func, _func_init)			\
@@ -248,10 +252,7 @@
 	return 0;
 }
 
-static inline long __static_call_return0(void)
-{
-	return 0;
-}
+extern long __static_call_return0(void);
 
 #define EXPORT_STATIC_CALL(name)					\
 	EXPORT_SYMBOL(STATIC_CALL_KEY(name));				\
@@ -268,6 +269,8 @@
 
 #else /* Generic implementation */
 
+#define static_call_initialized 0
+
 static inline int static_call_init(void) { return 0; }
 
 static inline long __static_call_return0(void)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/stddef.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/stddef.h
@@ -36,4 +36,65 @@
 #define offsetofend(TYPE, MEMBER) \
 	(offsetof(TYPE, MEMBER)	+ sizeof_field(TYPE, MEMBER))
 
+/**
+ * struct_group() - Wrap a set of declarations in a mirrored struct
+ *
+ * @NAME: The identifier name of the mirrored sub-struct
+ * @MEMBERS: The member declarations for the mirrored structs
+ *
+ * Used to create an anonymous union of two structs with identical
+ * layout and size: one anonymous and one named. The former can be
+ * used normally without sub-struct naming, and the latter can be
+ * used to reason about the start, end, and size of the group of
+ * struct members.
+ */
+#define struct_group(NAME, MEMBERS...)	\
+	__struct_group(/* no tag */, NAME, /* no attrs */, MEMBERS)
+
+/**
+ * struct_group_attr() - Create a struct_group() with trailing attributes
+ *
+ * @NAME: The identifier name of the mirrored sub-struct
+ * @ATTRS: Any struct attributes to apply
+ * @MEMBERS: The member declarations for the mirrored structs
+ *
+ * Used to create an anonymous union of two structs with identical
+ * layout and size: one anonymous and one named. The former can be
+ * used normally without sub-struct naming, and the latter can be
+ * used to reason about the start, end, and size of the group of
+ * struct members. Includes structure attributes argument.
+ */
+#define struct_group_attr(NAME, ATTRS, MEMBERS...) \
+	__struct_group(/* no tag */, NAME, ATTRS, MEMBERS)
+
+/**
+ * struct_group_tagged() - Create a struct_group with a reusable tag
+ *
+ * @TAG: The tag name for the named sub-struct
+ * @NAME: The identifier name of the mirrored sub-struct
+ * @MEMBERS: The member declarations for the mirrored structs
+ *
+ * Used to create an anonymous union of two structs with identical
+ * layout and size: one anonymous and one named. The former can be
+ * used normally without sub-struct naming, and the latter can be
+ * used to reason about the start, end, and size of the group of
+ * struct members. Includes struct tag argument for the named copy,
+ * so the specified layout can be reused later.
+ */
+#define struct_group_tagged(TAG, NAME, MEMBERS...) \
+	__struct_group(TAG, NAME, /* no attrs */, MEMBERS)
+
+/**
+ * DECLARE_FLEX_ARRAY() - Declare a flexible array usable in a union
+ *
+ * @TYPE: The type of each flexible array element
+ * @NAME: The name of the flexible array member
+ *
+ * In order to have a flexible array member in a union or alone in a
+ * struct, it needs to be wrapped in an anonymous struct with at least 1
+ * named member, but that member can be empty.
+ */
+#define DECLARE_FLEX_ARRAY(TYPE, NAME) \
+	__DECLARE_FLEX_ARRAY(TYPE, NAME)
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/stmmac.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/stmmac.h
@@ -172,6 +172,7 @@
 	bool hs_enable;				/* FPE handshake enable */
 	enum stmmac_fpe_state lp_fpe_state;	/* Link Partner FPE state */
 	enum stmmac_fpe_state lo_fpe_state;	/* Local station FPE state */
+	u32 fpe_csr;				/* MAC_FPE_CTRL_STS reg cache */
 };
 
 struct stmmac_safety_feature_cfg {
@@ -233,6 +234,7 @@
 	int (*clks_config)(void *priv, bool enabled);
 	int (*crosststamp)(ktime_t *device, struct system_counterval_t *system,
 			   void *ctx);
+	void (*dump_debug_regs)(void *priv);
 	void *bsp_priv;
 	struct clk *stmmac_clk;
 	struct clk *pclk;
@@ -250,6 +252,7 @@
 	int rss_en;
 	int mac_port_sel_speed;
 	bool en_tx_lpi_clockgating;
+	bool rx_clk_runs_in_lpi;
 	int has_xgmac;
 	bool vlan_fail_q_en;
 	u8 vlan_fail_q;
@@ -258,6 +261,7 @@
 	bool has_crossts;
 	int int_snapshot_num;
 	int ext_snapshot_num;
+	bool int_snapshot_en;
 	bool ext_snapshot_en;
 	bool multi_msi_en;
 	int msi_mac_vec;
@@ -268,5 +272,6 @@
 	int msi_rx_base_vec;
 	int msi_tx_base_vec;
 	bool use_phy_wol;
+	bool sph_disable;
 };
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/string.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/string.h
@@ -5,7 +5,9 @@
 #include <linux/compiler.h>	/* for inline */
 #include <linux/types.h>	/* for size_t */
 #include <linux/stddef.h>	/* for NULL */
+#include <linux/err.h>		/* for ERR_PTR() */
 #include <linux/errno.h>	/* for E2BIG */
+#include <linux/overflow.h>	/* for check_mul_overflow() */
 #include <linux/stdarg.h>
 #include <uapi/linux/string.h>
 
@@ -14,6 +16,44 @@
 extern void *vmemdup_user(const void __user *, size_t);
 extern void *memdup_user_nul(const void __user *, size_t);
 
+/**
+ * memdup_array_user - duplicate array from user space
+ * @src: source address in user space
+ * @n: number of array members to copy
+ * @size: size of one array member
+ *
+ * Return: an ERR_PTR() on failure. Result is physically
+ * contiguous, to be freed by kfree().
+ */
+static inline void *memdup_array_user(const void __user *src, size_t n, size_t size)
+{
+	size_t nbytes;
+
+	if (check_mul_overflow(n, size, &nbytes))
+		return ERR_PTR(-EOVERFLOW);
+
+	return memdup_user(src, nbytes);
+}
+
+/**
+ * vmemdup_array_user - duplicate array from user space
+ * @src: source address in user space
+ * @n: number of array members to copy
+ * @size: size of one array member
+ *
+ * Return: an ERR_PTR() on failure. Result may be not
+ * physically contiguous. Use kvfree() to free.
+ */
+static inline void *vmemdup_array_user(const void __user *src, size_t n, size_t size)
+{
+	size_t nbytes;
+
+	if (check_mul_overflow(n, size, &nbytes))
+		return ERR_PTR(-EOVERFLOW);
+
+	return vmemdup_user(src, nbytes);
+}
+
 /*
  * Include machine specific inline routines
  */
@@ -262,23 +302,8 @@
 #include <linux/fortify-string.h>
 #endif
 
-/**
- * memcpy_and_pad - Copy one buffer to another with padding
- * @dest: Where to copy to
- * @dest_len: The destination buffer size
- * @src: Where to copy from
- * @count: The number of bytes to copy
- * @pad: Character to use for padding if space is left in destination.
- */
-static inline void memcpy_and_pad(void *dest, size_t dest_len,
-				  const void *src, size_t count, int pad)
-{
-	if (dest_len > count) {
-		memcpy(dest, src, count);
-		memset(dest + count, pad,  dest_len - count);
-	} else
-		memcpy(dest, src, dest_len);
-}
+void memcpy_and_pad(void *dest, size_t dest_len, const void *src, size_t count,
+		    int pad);
 
 /**
  * str_has_prefix - Test if a string has a given prefix
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/clnt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/clnt.h
@@ -83,6 +83,7 @@
 	};
 	const struct cred	*cl_cred;
 	unsigned int		cl_max_connect; /* max number of transports not to the same IP */
+	struct super_block *pipefs_sb;
 };
 
 /*
@@ -129,6 +130,7 @@
 	const char		*servername;
 	const char		*nodename;
 	const struct rpc_program *program;
+	struct rpc_stat		*stats;
 	u32			prognumber;	/* overrides program->number */
 	u32			version;
 	rpc_authflavor_t	authflavor;
@@ -159,6 +161,7 @@
 #define RPC_CLNT_CREATE_NO_RETRANS_TIMEOUT	(1UL << 9)
 #define RPC_CLNT_CREATE_SOFTERR		(1UL << 10)
 #define RPC_CLNT_CREATE_REUSEPORT	(1UL << 11)
+#define RPC_CLNT_CREATE_CONNECTED	(1UL << 12)
 
 struct rpc_clnt *rpc_create(struct rpc_create_args *args);
 struct rpc_clnt	*rpc_bind_new_program(struct rpc_clnt *,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/rpc_pipe_fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/rpc_pipe_fs.h
@@ -92,6 +92,11 @@
 				       char __user *, size_t);
 extern int rpc_queue_upcall(struct rpc_pipe *, struct rpc_pipe_msg *);
 
+/* returns true if the msg is in-flight, i.e., already eaten by the peer */
+static inline bool rpc_msg_is_inflight(const struct rpc_pipe_msg *msg) {
+	return (msg->copied != 0 && list_empty(&msg->list));
+}
+
 struct rpc_clnt;
 extern struct dentry *rpc_create_client_dir(struct dentry *, const char *, struct rpc_clnt *);
 extern int rpc_remove_client_dir(struct rpc_clnt *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/sched.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/sched.h
@@ -90,8 +90,7 @@
 #endif
 	unsigned char		tk_priority : 2,/* Task priority */
 				tk_garb_retry : 2,
-				tk_cred_retry : 2,
-				tk_rebind_retry : 2;
+				tk_cred_retry : 2;
 };
 
 typedef void			(*rpc_action)(struct rpc_task *);
@@ -200,7 +199,7 @@
 	unsigned char		maxpriority;		/* maximum priority (0 if queue is not a priority queue) */
 	unsigned char		priority;		/* current priority */
 	unsigned char		nr;			/* # tasks remaining for cookie */
-	unsigned short		qlen;			/* total # tasks waiting in queue */
+	unsigned int		qlen;			/* total # tasks waiting in queue */
 	struct rpc_timer	timer_list;
 #if IS_ENABLED(CONFIG_SUNRPC_DEBUG) || IS_ENABLED(CONFIG_TRACEPOINTS)
 	const char *		name;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/svc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/svc.h
@@ -52,25 +52,6 @@
 	unsigned long		sp_flags;
 } ____cacheline_aligned_in_smp;
 
-struct svc_serv;
-
-struct svc_serv_ops {
-	/* Callback to use when last thread exits. */
-	void		(*svo_shutdown)(struct svc_serv *, struct net *);
-
-	/* function for service threads to run */
-	int		(*svo_function)(void *);
-
-	/* queue up a transport for servicing */
-	void		(*svo_enqueue_xprt)(struct svc_xprt *);
-
-	/* set up thread (or whatever) execution context */
-	int		(*svo_setup)(struct svc_serv *, struct svc_pool *, int);
-
-	/* optional module to count when adding threads (pooled svcs only) */
-	struct module	*svo_module;
-};
-
 /*
  * RPC service.
  *
@@ -85,6 +66,7 @@
 	struct svc_program *	sv_program;	/* RPC program */
 	struct svc_stat *	sv_stats;	/* RPC statistics */
 	spinlock_t		sv_lock;
+	struct kref		sv_refcnt;
 	unsigned int		sv_nrthreads;	/* # of server threads */
 	unsigned int		sv_maxconn;	/* max connections allowed or
 						 * '0' causing max to be based
@@ -102,7 +84,8 @@
 
 	unsigned int		sv_nrpools;	/* number of thread pools */
 	struct svc_pool *	sv_pools;	/* array of thread pools */
-	const struct svc_serv_ops *sv_ops;	/* server operations */
+	int			(*sv_threadfn)(void *data);
+
 #if defined(CONFIG_SUNRPC_BACKCHANNEL)
 	struct list_head	sv_cb_list;	/* queue for callback requests
 						 * that arrive over the same
@@ -114,15 +97,30 @@
 #endif /* CONFIG_SUNRPC_BACKCHANNEL */
 };
 
-/*
- * We use sv_nrthreads as a reference count.  svc_destroy() drops
- * this refcount, so we need to bump it up around operations that
- * change the number of threads.  Horrible, but there it is.
- * Should be called with the "service mutex" held.
+/**
+ * svc_get() - increment reference count on a SUNRPC serv
+ * @serv:  the svc_serv to have count incremented
+ *
+ * Returns: the svc_serv that was passed in.
+ */
+static inline struct svc_serv *svc_get(struct svc_serv *serv)
+{
+	kref_get(&serv->sv_refcnt);
+	return serv;
+}
+
+void svc_destroy(struct kref *);
+
+/**
+ * svc_put - decrement reference count on a SUNRPC serv
+ * @serv:  the svc_serv to have count decremented
+ *
+ * When the reference count reaches zero, svc_destroy()
+ * is called to clean up and free the serv.
  */
-static inline void svc_get(struct svc_serv *serv)
+static inline void svc_put(struct svc_serv *serv)
 {
-	serv->sv_nrthreads++;
+	kref_put(&serv->sv_refcnt, svc_destroy);
 }
 
 /*
@@ -246,7 +244,6 @@
 	void *			rq_xprt_ctxt;	/* transport specific context ptr */
 	struct svc_deferred_req*rq_deferred;	/* deferred request we are replaying */
 
-	size_t			rq_xprt_hlen;	/* xprt header len */
 	struct xdr_buf		rq_arg;
 	struct xdr_stream	rq_arg_stream;
 	struct xdr_stream	rq_res_stream;
@@ -384,8 +381,8 @@
 	size_t			addrlen;
 	struct sockaddr_storage	daddr;	/* where reply must come from */
 	size_t			daddrlen;
+	void			*xprt_ctxt;
 	struct cache_deferred_req handle;
-	size_t			xprt_hlen;
 	int			argslen;
 	__be32			args[];
 };
@@ -412,7 +409,6 @@
 	const struct svc_version **pg_vers;	/* version array */
 	char *			pg_name;	/* service name */
 	char *			pg_class;	/* class name: services sharing authentication */
-	struct svc_stat *	pg_stats;	/* rpc statistics */
 	int			(*pg_authenticate)(struct svc_rqst *);
 	__be32			(*pg_init_request)(struct svc_rqst *,
 						   const struct svc_program *,
@@ -457,12 +453,15 @@
 	/* process the request: */
 	__be32			(*pc_func)(struct svc_rqst *);
 	/* XDR decode args: */
-	int			(*pc_decode)(struct svc_rqst *, __be32 *data);
+	bool			(*pc_decode)(struct svc_rqst *rqstp,
+					     struct xdr_stream *xdr);
 	/* XDR encode result: */
-	int			(*pc_encode)(struct svc_rqst *, __be32 *data);
+	bool			(*pc_encode)(struct svc_rqst *rqstp,
+					     struct xdr_stream *xdr);
 	/* XDR free result: */
 	void			(*pc_release)(struct svc_rqst *);
 	unsigned int		pc_argsize;	/* argument struct size */
+	unsigned int		pc_argzero;	/* how much of argument to clear */
 	unsigned int		pc_ressize;	/* result struct size */
 	unsigned int		pc_cachetype;	/* cache info (NFS) */
 	unsigned int		pc_xdrressize;	/* maximum size of XDR reply */
@@ -470,53 +469,25 @@
 };
 
 /*
- * Mode for mapping cpus to pools.
- */
-enum {
-	SVC_POOL_AUTO = -1,	/* choose one of the others */
-	SVC_POOL_GLOBAL,	/* no mapping, just a single global pool
-				 * (legacy & UP mode) */
-	SVC_POOL_PERCPU,	/* one pool per cpu */
-	SVC_POOL_PERNODE	/* one pool per numa node */
-};
-
-struct svc_pool_map {
-	int count;			/* How many svc_servs use us */
-	int mode;			/* Note: int not enum to avoid
-					 * warnings about "enumeration value
-					 * not handled in switch" */
-	unsigned int npools;
-	unsigned int *pool_to;		/* maps pool id to cpu or node */
-	unsigned int *to_pool;		/* maps cpu or node to pool id */
-};
-
-extern struct svc_pool_map svc_pool_map;
-
-/*
  * Function prototypes.
  */
 int svc_rpcb_setup(struct svc_serv *serv, struct net *net);
 void svc_rpcb_cleanup(struct svc_serv *serv, struct net *net);
 int svc_bind(struct svc_serv *serv, struct net *net);
 struct svc_serv *svc_create(struct svc_program *, unsigned int,
-			    const struct svc_serv_ops *);
+			    int (*threadfn)(void *data));
 struct svc_rqst *svc_rqst_alloc(struct svc_serv *serv,
 					struct svc_pool *pool, int node);
-struct svc_rqst *svc_prepare_thread(struct svc_serv *serv,
-					struct svc_pool *pool, int node);
 void		   svc_rqst_replace_page(struct svc_rqst *rqstp,
 					 struct page *page);
 void		   svc_rqst_free(struct svc_rqst *);
 void		   svc_exit_thread(struct svc_rqst *);
-unsigned int	   svc_pool_map_get(void);
-void		   svc_pool_map_put(void);
-struct svc_serv *  svc_create_pooled(struct svc_program *, unsigned int,
-			const struct svc_serv_ops *);
+struct svc_serv *  svc_create_pooled(struct svc_program *prog,
+				     struct svc_stat *stats,
+				     unsigned int bufsize,
+				     int (*threadfn)(void *data));
 int		   svc_set_num_threads(struct svc_serv *, struct svc_pool *, int);
-int		   svc_set_num_threads_sync(struct svc_serv *, struct svc_pool *, int);
 int		   svc_pool_stats_open(struct svc_serv *serv, struct file *file);
-void		   svc_destroy(struct svc_serv *);
-void		   svc_shutdown_net(struct svc_serv *, struct net *);
 int		   svc_process(struct svc_rqst *);
 int		   bc_svc_process(struct svc_serv *, struct rpc_rqst *,
 			struct svc_rqst *);
@@ -532,8 +503,7 @@
 					     unsigned int offset,
 					     unsigned int length);
 unsigned int	   svc_fill_write_vector(struct svc_rqst *rqstp,
-					 struct page **pages,
-					 struct kvec *first, size_t total);
+					 struct xdr_buf *payload);
 char		  *svc_fill_symlink_pathname(struct svc_rqst *rqstp,
 					     struct kvec *first, void *p,
 					     size_t total);
@@ -566,16 +536,27 @@
 }
 
 /**
- * svcxdr_init_decode - Prepare an xdr_stream for svc Call decoding
+ * svcxdr_init_decode - Prepare an xdr_stream for Call decoding
  * @rqstp: controlling server RPC transaction context
  *
+ * This function currently assumes the RPC header in rq_arg has
+ * already been decoded. Upon return, xdr->p points to the
+ * location of the upper layer header.
  */
 static inline void svcxdr_init_decode(struct svc_rqst *rqstp)
 {
 	struct xdr_stream *xdr = &rqstp->rq_arg_stream;
-	struct kvec *argv = rqstp->rq_arg.head;
+	struct xdr_buf *buf = &rqstp->rq_arg;
+	struct kvec *argv = buf->head;
+
+	/*
+	 * svc_getnl() and friends do not keep the xdr_buf's ::len
+	 * field up to date. Refresh that field before initializing
+	 * the argument decoding stream.
+	 */
+	buf->len = buf->head->iov_len + buf->page_len + buf->tail->iov_len;
 
-	xdr_init_decode(xdr, &rqstp->rq_arg, argv->iov_base, NULL);
+	xdr_init_decode(xdr, buf, argv->iov_base, NULL);
 	xdr_set_scratch_page(xdr, rqstp->rq_scratch_page);
 }
 
@@ -598,7 +579,7 @@
 	xdr->end = resv->iov_base + PAGE_SIZE - rqstp->rq_auth_slack;
 	buf->len = resv->iov_len;
 	xdr->page_ptr = buf->pages - 1;
-	buf->buflen = PAGE_SIZE * (1 + rqstp->rq_page_end - buf->pages);
+	buf->buflen = PAGE_SIZE * (rqstp->rq_page_end - buf->pages);
 	buf->buflen -= rqstp->rq_auth_slack;
 	xdr->rqst = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/svc_rdma.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/svc_rdma.h
@@ -176,7 +176,7 @@
 extern void svc_rdma_recv_ctxt_put(struct svcxprt_rdma *rdma,
 				   struct svc_rdma_recv_ctxt *ctxt);
 extern void svc_rdma_flush_recv_queues(struct svcxprt_rdma *rdma);
-extern void svc_rdma_release_rqst(struct svc_rqst *rqstp);
+extern void svc_rdma_release_ctxt(struct svc_xprt *xprt, void *ctxt);
 extern int svc_rdma_recvfrom(struct svc_rqst *);
 
 /* svc_rdma_rw.c */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/svc_xprt.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/svc_xprt.h
@@ -23,7 +23,7 @@
 	int		(*xpo_sendto)(struct svc_rqst *);
 	int		(*xpo_result_payload)(struct svc_rqst *, unsigned int,
 					      unsigned int);
-	void		(*xpo_release_rqst)(struct svc_rqst *);
+	void		(*xpo_release_ctxt)(struct svc_xprt *xprt, void *ctxt);
 	void		(*xpo_detach)(struct svc_xprt *);
 	void		(*xpo_free)(struct svc_xprt *);
 	void		(*xpo_secure_port)(struct svc_rqst *rqstp);
@@ -127,15 +127,16 @@
 void	svc_unreg_xprt_class(struct svc_xprt_class *);
 void	svc_xprt_init(struct net *, struct svc_xprt_class *, struct svc_xprt *,
 		      struct svc_serv *);
-int	svc_create_xprt(struct svc_serv *, const char *, struct net *,
-			const int, const unsigned short, int,
-			const struct cred *);
+int	svc_xprt_create(struct svc_serv *serv, const char *xprt_name,
+			struct net *net, const int family,
+			const unsigned short port, int flags,
+			const struct cred *cred);
+void	svc_xprt_destroy_all(struct svc_serv *serv, struct net *net);
 void	svc_xprt_received(struct svc_xprt *xprt);
-void	svc_xprt_do_enqueue(struct svc_xprt *xprt);
 void	svc_xprt_enqueue(struct svc_xprt *xprt);
 void	svc_xprt_put(struct svc_xprt *xprt);
 void	svc_xprt_copy_addrs(struct svc_rqst *rqstp, struct svc_xprt *xprt);
-void	svc_close_xprt(struct svc_xprt *xprt);
+void	svc_xprt_close(struct svc_xprt *xprt);
 int	svc_port_is_privileged(struct sockaddr *sin);
 int	svc_print_xprts(char *buf, int maxlen);
 struct	svc_xprt *svc_find_xprt(struct svc_serv *serv, const char *xcl_name,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/svcsock.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/svcsock.h
@@ -59,10 +59,9 @@
 int		svc_send(struct svc_rqst *);
 void		svc_drop(struct svc_rqst *);
 void		svc_sock_update_bufs(struct svc_serv *serv);
-bool		svc_alien_sock(struct net *net, int fd);
-int		svc_addsock(struct svc_serv *serv, const int fd,
-					char *name_return, const size_t len,
-					const struct cred *cred);
+int		svc_addsock(struct svc_serv *serv, struct net *net,
+			    const int fd, char *name_return, const size_t len,
+			    const struct cred *cred);
 void		svc_init_xprt_sock(void);
 void		svc_cleanup_xprt_sock(void);
 struct svc_xprt *svc_sock_create(struct svc_serv *serv, int prot);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/xdr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/xdr.h
@@ -240,6 +240,8 @@
 
 extern void xdr_init_encode(struct xdr_stream *xdr, struct xdr_buf *buf,
 			    __be32 *p, struct rpc_rqst *rqst);
+extern void xdr_init_encode_pages(struct xdr_stream *xdr, struct xdr_buf *buf,
+			   struct page **pages, struct rpc_rqst *rqst);
 extern __be32 *xdr_reserve_space(struct xdr_stream *xdr, size_t nbytes);
 extern int xdr_reserve_space_vec(struct xdr_stream *xdr, struct kvec *vec,
 		size_t nbytes);
@@ -405,8 +407,8 @@
  */
 static inline __be32 *xdr_encode_bool(__be32 *p, u32 n)
 {
-	*p = n ? xdr_one : xdr_zero;
-	return p++;
+	*p++ = n ? xdr_one : xdr_zero;
+	return p;
 }
 
 /**
@@ -731,6 +733,8 @@
 
 	if (unlikely(xdr_stream_decode_u32(xdr, &len) < 0))
 		return -EBADMSG;
+	if (len > SIZE_MAX / sizeof(*p))
+		return -EBADMSG;
 	p = xdr_inline_decode(xdr, len * sizeof(*p));
 	if (unlikely(!p))
 		return -EBADMSG;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sunrpc/xprtsock.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sunrpc/xprtsock.h
@@ -89,5 +89,7 @@
 #define XPRT_SOCK_WAKE_WRITE	(5)
 #define XPRT_SOCK_WAKE_PENDING	(6)
 #define XPRT_SOCK_WAKE_DISCONNECT	(7)
+#define XPRT_SOCK_CONNECT_SENT	(8)
+#define XPRT_SOCK_NOSPACE	(9)
 
 #endif /* _LINUX_SUNRPC_XPRTSOCK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/surface_aggregator/controller.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/surface_aggregator/controller.h
@@ -792,8 +792,8 @@
 #define SSAM_EVENT_REGISTRY_KIP	\
 	SSAM_EVENT_REGISTRY(SSAM_SSH_TC_KIP, 0x02, 0x27, 0x28)
 
-#define SSAM_EVENT_REGISTRY_REG \
-	SSAM_EVENT_REGISTRY(SSAM_SSH_TC_REG, 0x02, 0x01, 0x02)
+#define SSAM_EVENT_REGISTRY_REG(tid)\
+	SSAM_EVENT_REGISTRY(SSAM_SSH_TC_REG, tid, 0x01, 0x02)
 
 /**
  * enum ssam_event_notifier_flags - Flags for event notifiers.
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/suspend.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/suspend.h
@@ -430,15 +430,7 @@
 
 #ifdef CONFIG_HIBERNATION
 /* kernel/power/snapshot.c */
-extern void __register_nosave_region(unsigned long b, unsigned long e, int km);
-static inline void __init register_nosave_region(unsigned long b, unsigned long e)
-{
-	__register_nosave_region(b, e, 0);
-}
-static inline void __init register_nosave_region_late(unsigned long b, unsigned long e)
-{
-	__register_nosave_region(b, e, 1);
-}
+extern void register_nosave_region(unsigned long b, unsigned long e);
 extern int swsusp_page_is_forbidden(struct page *);
 extern void swsusp_set_page_free(struct page *);
 extern void swsusp_unset_page_free(struct page *);
@@ -457,7 +449,6 @@
 int hibernate_quiet_exec(int (*func)(void *data), void *data);
 #else /* CONFIG_HIBERNATION */
 static inline void register_nosave_region(unsigned long b, unsigned long e) {}
-static inline void register_nosave_region_late(unsigned long b, unsigned long e) {}
 static inline int swsusp_page_is_forbidden(struct page *p) { return 0; }
 static inline void swsusp_set_page_free(struct page *p) {}
 static inline void swsusp_unset_page_free(struct page *p) {}
@@ -505,14 +496,14 @@
 
 /* drivers/base/power/wakeup.c */
 extern bool events_check_enabled;
-extern unsigned int pm_wakeup_irq;
 extern suspend_state_t pm_suspend_target_state;
 
 extern bool pm_wakeup_pending(void);
 extern void pm_system_wakeup(void);
 extern void pm_system_cancel_wakeup(void);
-extern void pm_wakeup_clear(bool reset);
+extern void pm_wakeup_clear(unsigned int irq_number);
 extern void pm_system_irq_wakeup(unsigned int irq_number);
+extern unsigned int pm_wakeup_irq(void);
 extern bool pm_get_wakeup_count(unsigned int *count, bool block);
 extern bool pm_save_wakeup_count(unsigned int count);
 extern void pm_wakep_autosleep_enabled(bool set);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/swap.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/swap.h
@@ -378,7 +378,6 @@
 extern unsigned long zone_reclaimable_pages(struct zone *zone);
 extern unsigned long try_to_free_pages(struct zonelist *zonelist, int order,
 					gfp_t gfp_mask, nodemask_t *mask);
-extern bool __isolate_lru_page_prepare(struct page *page, isolate_mode_t mode);
 extern unsigned long try_to_free_mem_cgroup_pages(struct mem_cgroup *memcg,
 						  unsigned long nr_pages,
 						  gfp_t gfp_mask,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/swiotlb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/swiotlb.h
@@ -45,7 +45,8 @@
 
 phys_addr_t swiotlb_tbl_map_single(struct device *hwdev, phys_addr_t phys,
 		size_t mapping_size, size_t alloc_size,
-		enum dma_data_direction dir, unsigned long attrs);
+		unsigned int alloc_aligned_mask, enum dma_data_direction dir,
+		unsigned long attrs);
 
 extern void swiotlb_tbl_unmap_single(struct device *hwdev,
 				     phys_addr_t tlb_addr,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/syscalls.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/syscalls.h
@@ -122,6 +122,7 @@
 #define __TYPE_IS_LL(t) (__TYPE_AS(t, 0LL) || __TYPE_AS(t, 0ULL))
 #define __SC_LONG(t, a) __typeof(__builtin_choose_expr(__TYPE_IS_LL(t), 0LL, 0L)) a
 #define __SC_CAST(t, a)	(__force t) a
+#define __SC_TYPE(t, a)	t
 #define __SC_ARGS(t, a)	a
 #define __SC_TEST(t, a) (void)BUILD_BUG_ON_ZERO(!__TYPE_IS_LL(t) && sizeof(t) > sizeof(long))
 
@@ -452,7 +453,7 @@
 asmlinkage long sys_fstatfs64(unsigned int fd, size_t sz,
 				struct statfs64 __user *buf);
 asmlinkage long sys_truncate(const char __user *path, long length);
-asmlinkage long sys_ftruncate(unsigned int fd, unsigned long length);
+asmlinkage long sys_ftruncate(unsigned int fd, off_t length);
 #if BITS_PER_LONG == 32
 asmlinkage long sys_truncate64(const char __user *path, loff_t length);
 asmlinkage long sys_ftruncate64(unsigned int fd, loff_t length);
@@ -958,9 +959,15 @@
 				const struct rlimit64 __user *new_rlim,
 				struct rlimit64 __user *old_rlim);
 asmlinkage long sys_fanotify_init(unsigned int flags, unsigned int event_f_flags);
+#if defined(CONFIG_ARCH_SPLIT_ARG64)
+asmlinkage long sys_fanotify_mark(int fanotify_fd, unsigned int flags,
+                                unsigned int mask_1, unsigned int mask_2,
+				int dfd, const char  __user * pathname);
+#else
 asmlinkage long sys_fanotify_mark(int fanotify_fd, unsigned int flags,
 				  u64 mask, int fd,
 				  const char  __user *pathname);
+#endif
 asmlinkage long sys_name_to_handle_at(int dfd, const char __user *name,
 				      struct file_handle __user *handle,
 				      int __user *mnt_id, int flag);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sysctl.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sysctl.h
@@ -38,12 +38,25 @@
 struct ctl_dir;
 
 /* Keep the same order as in fs/proc/proc_sysctl.c */
-#define SYSCTL_ZERO	((void *)&sysctl_vals[0])
-#define SYSCTL_ONE	((void *)&sysctl_vals[1])
-#define SYSCTL_INT_MAX	((void *)&sysctl_vals[2])
+#define SYSCTL_NEG_ONE			((void *)&sysctl_vals[0])
+#define SYSCTL_ZERO			((void *)&sysctl_vals[1])
+#define SYSCTL_ONE			((void *)&sysctl_vals[2])
+#define SYSCTL_TWO			((void *)&sysctl_vals[3])
+#define SYSCTL_FOUR			((void *)&sysctl_vals[4])
+#define SYSCTL_ONE_HUNDRED		((void *)&sysctl_vals[5])
+#define SYSCTL_TWO_HUNDRED		((void *)&sysctl_vals[6])
+#define SYSCTL_ONE_THOUSAND		((void *)&sysctl_vals[7])
+#define SYSCTL_THREE_THOUSAND		((void *)&sysctl_vals[8])
+#define SYSCTL_INT_MAX			((void *)&sysctl_vals[9])
 
 extern const int sysctl_vals[];
 
+#define SYSCTL_LONG_ZERO	((void *)&sysctl_long_vals[0])
+#define SYSCTL_LONG_ONE		((void *)&sysctl_long_vals[1])
+#define SYSCTL_LONG_MAX		((void *)&sysctl_long_vals[2])
+
+extern const unsigned long sysctl_long_vals[];
+
 typedef int proc_handler(struct ctl_table *ctl, int write, void *buffer,
 		size_t *lenp, loff_t *ppos);
 
@@ -199,7 +212,11 @@
 void unregister_sysctl_table(struct ctl_table_header * table);
 
 extern int sysctl_init(void);
+extern void __register_sysctl_init(const char *path, struct ctl_table *table,
+				 const char *table_name);
+#define register_sysctl_init(path, table) __register_sysctl_init(path, table, #table)
 void do_sysctl_args(void);
+bool sysctl_is_alias(char *param);
 
 extern int pwrsw_enabled;
 extern int unaligned_enabled;
@@ -241,6 +258,11 @@
 static inline void do_sysctl_args(void)
 {
 }
+
+static inline bool sysctl_is_alias(char *param)
+{
+	return false;
+}
 #endif /* CONFIG_SYSCTL */
 
 int sysctl_max_threads(struct ctl_table *table, int write, void *buffer,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/sysfb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/sysfb.h
@@ -55,14 +55,31 @@
 	int flags;
 };
 
+#ifdef CONFIG_SYSFB
+
+void sysfb_disable(void);
+
+#else /* CONFIG_SYSFB */
+
+static inline void sysfb_disable(void)
+{
+}
+
+#endif /* CONFIG_SYSFB */
+
 #ifdef CONFIG_EFI
 
 extern struct efifb_dmi_info efifb_dmi_list[];
-void sysfb_apply_efi_quirks(struct platform_device *pd);
+void sysfb_apply_efi_quirks(void);
+void sysfb_set_efifb_fwnode(struct platform_device *pd);
 
 #else /* CONFIG_EFI */
 
-static inline void sysfb_apply_efi_quirks(struct platform_device *pd)
+static inline void sysfb_apply_efi_quirks(void)
+{
+}
+
+static inline void sysfb_set_efifb_fwnode(struct platform_device *pd)
 {
 }
 
@@ -72,8 +89,8 @@
 
 bool sysfb_parse_mode(const struct screen_info *si,
 		      struct simplefb_platform_data *mode);
-int sysfb_create_simplefb(const struct screen_info *si,
-			  const struct simplefb_platform_data *mode);
+struct platform_device *sysfb_create_simplefb(const struct screen_info *si,
+					      const struct simplefb_platform_data *mode);
 
 #else /* CONFIG_SYSFB_SIMPLE */
 
@@ -83,10 +100,10 @@
 	return false;
 }
 
-static inline int sysfb_create_simplefb(const struct screen_info *si,
-					 const struct simplefb_platform_data *mode)
+static inline struct platform_device *sysfb_create_simplefb(const struct screen_info *si,
+							    const struct simplefb_platform_data *mode)
 {
-	return -EINVAL;
+	return ERR_PTR(-EINVAL);
 }
 
 #endif /* CONFIG_SYSFB_SIMPLE */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/task_work.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/task_work.h
@@ -24,7 +24,8 @@
 
 struct callback_head *task_work_cancel_match(struct task_struct *task,
 	bool (*match)(struct callback_head *, void *data), void *data);
-struct callback_head *task_work_cancel(struct task_struct *, task_work_func_t);
+struct callback_head *task_work_cancel_func(struct task_struct *, task_work_func_t);
+bool task_work_cancel(struct task_struct *task, struct callback_head *cb);
 void task_work_run(void);
 
 static inline void exit_task_work(struct task_struct *task)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tca6416_keypad.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tca6416_keypad.h
@@ -25,7 +25,6 @@
 	unsigned int rep:1;	/* enable input subsystem auto repeat */
 	uint16_t pinmask;
 	uint16_t invert;
-	int irq_is_gpio;
 	int use_polling;	/* use polling if Interrupt is not connected*/
 };
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tcp.h
@@ -265,7 +265,7 @@
 	u32	packets_out;	/* Packets which are "in flight"	*/
 	u32	retrans_out;	/* Retransmitted packets out		*/
 	u32	max_packets_out;  /* max packets_out in last window */
-	u32	max_packets_seq;  /* right edge of max_packets_out flight */
+	u32	cwnd_usage_seq;  /* right edge of cwnd usage tracking flight */
 
 	u16	urg_data;	/* Saved octet of OOB data and control flags */
 	u8	ecn_flags;	/* ECN status bits.			*/
@@ -473,7 +473,7 @@
 	struct request_sock_queue *queue = &inet_csk(sk)->icsk_accept_queue;
 	int somaxconn = READ_ONCE(sock_net(sk)->core.sysctl_somaxconn);
 
-	queue->fastopenq.max_qlen = min_t(unsigned int, backlog, somaxconn);
+	WRITE_ONCE(queue->fastopenq.max_qlen, min_t(unsigned int, backlog, somaxconn));
 }
 
 static inline void tcp_move_syn(struct tcp_sock *tp,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tee_drv.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tee_drv.h
@@ -195,7 +195,7 @@
  * @offset:	offset of buffer in user space
  * @pages:	locked pages from userspace
  * @num_pages:	number of locked pages
- * @dmabuf:	dmabuf used to for exporting to user space
+ * @refcount:	reference counter
  * @flags:	defined by TEE_SHM_* in tee_drv.h
  * @id:		unique id of a shared memory object on this device
  *
@@ -210,7 +210,7 @@
 	unsigned int offset;
 	struct page **pages;
 	size_t num_pages;
-	struct dma_buf *dmabuf;
+	refcount_t refcount;
 	u32 flags;
 	int id;
 };
@@ -582,4 +582,18 @@
 #define to_tee_client_driver(d) \
 		container_of(d, struct tee_client_driver, driver)
 
+/**
+ * teedev_open() - Open a struct tee_device
+ * @teedev:	Device to open
+ *
+ * @return a pointer to struct tee_context on success or an ERR_PTR on failure.
+ */
+struct tee_context *teedev_open(struct tee_device *teedev);
+
+/**
+ * teedev_close_context() - closes a struct tee_context
+ * @ctx:	The struct tee_context to close
+ */
+void teedev_close_context(struct tee_context *ctx);
+
 #endif /*__TEE_DRV_H*/
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/thermal.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/thermal.h
@@ -92,6 +92,7 @@
 struct thermal_cooling_device {
 	int id;
 	char *type;
+	unsigned long max_state;
 	struct device device;
 	struct device_node *np;
 	void *devdata;
@@ -113,7 +114,7 @@
  * @trip_hyst_attrs:	attributes for trip points for sysfs: trip hysteresis
  * @mode:		current mode of this thermal zone
  * @devdata:	private pointer for device private data
- * @trips:	number of trip points the thermal zone supports
+ * @num_trips:	number of trip points the thermal zone supports
  * @trips_disabled;	bitmap for disabled trips
  * @passive_delay_jiffies: number of jiffies to wait between polls when
  *			performing passive cooling.
@@ -153,7 +154,7 @@
 	struct thermal_attr *trip_hyst_attrs;
 	enum thermal_device_mode mode;
 	void *devdata;
-	int trips;
+	int num_trips;
 	unsigned long trips_disabled;	/* bitmap for disabled trips */
 	unsigned long passive_delay_jiffies;
 	unsigned long polling_delay_jiffies;
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/thread_info.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/thread_info.h
@@ -118,6 +118,15 @@
 	return test_bit(flag, (unsigned long *)&ti->flags);
 }
 
+/*
+ * This may be used in noinstr code, and needs to be __always_inline to prevent
+ * inadvertent instrumentation.
+ */
+static __always_inline unsigned long read_ti_thread_flags(struct thread_info *ti)
+{
+	return READ_ONCE(ti->flags);
+}
+
 #define set_thread_flag(flag) \
 	set_ti_thread_flag(current_thread_info(), flag)
 #define clear_thread_flag(flag) \
@@ -130,6 +139,11 @@
 	test_and_clear_ti_thread_flag(current_thread_info(), flag)
 #define test_thread_flag(flag) \
 	test_ti_thread_flag(current_thread_info(), flag)
+#define read_thread_flags() \
+	read_ti_thread_flags(current_thread_info())
+
+#define read_task_thread_flags(t) \
+	read_ti_thread_flags(task_thread_info(t))
 
 #ifdef CONFIG_GENERIC_ENTRY
 #define set_syscall_work(fl) \
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tick.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tick.h
@@ -216,6 +216,7 @@
 				     enum tick_dep_bits bit);
 extern void tick_nohz_dep_clear_signal(struct signal_struct *signal,
 				       enum tick_dep_bits bit);
+extern bool tick_nohz_cpu_hotpluggable(unsigned int cpu);
 
 /*
  * The below are tick_nohz_[set,clear]_dep() wrappers that optimize off-cases
@@ -251,12 +252,19 @@
 	if (tick_nohz_full_enabled())
 		tick_nohz_dep_set_task(tsk, bit);
 }
+
 static inline void tick_dep_clear_task(struct task_struct *tsk,
 				       enum tick_dep_bits bit)
 {
 	if (tick_nohz_full_enabled())
 		tick_nohz_dep_clear_task(tsk, bit);
 }
+
+static inline void tick_dep_init_task(struct task_struct *tsk)
+{
+	atomic_set(&tsk->tick_dep_mask, 0);
+}
+
 static inline void tick_dep_set_signal(struct task_struct *tsk,
 				       enum tick_dep_bits bit)
 {
@@ -280,6 +288,7 @@
 
 static inline void tick_nohz_dep_set_cpu(int cpu, enum tick_dep_bits bit) { }
 static inline void tick_nohz_dep_clear_cpu(int cpu, enum tick_dep_bits bit) { }
+static inline bool tick_nohz_cpu_hotpluggable(unsigned int cpu) { return true; }
 
 static inline void tick_dep_set(enum tick_dep_bits bit) { }
 static inline void tick_dep_clear(enum tick_dep_bits bit) { }
@@ -289,6 +298,7 @@
 				     enum tick_dep_bits bit) { }
 static inline void tick_dep_clear_task(struct task_struct *tsk,
 				       enum tick_dep_bits bit) { }
+static inline void tick_dep_init_task(struct task_struct *tsk) { }
 static inline void tick_dep_set_signal(struct task_struct *tsk,
 				       enum tick_dep_bits bit) { }
 static inline void tick_dep_clear_signal(struct signal_struct *signal,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/timer.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/timer.h
@@ -169,7 +169,6 @@
 }
 
 extern void add_timer_on(struct timer_list *timer, int cpu);
-extern int del_timer(struct timer_list * timer);
 extern int mod_timer(struct timer_list *timer, unsigned long expires);
 extern int mod_timer_pending(struct timer_list *timer, unsigned long expires);
 extern int timer_reduce(struct timer_list *timer, unsigned long expires);
@@ -183,15 +182,39 @@
 extern void add_timer(struct timer_list *timer);
 
 extern int try_to_del_timer_sync(struct timer_list *timer);
-
-#if defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT)
-  extern int del_timer_sync(struct timer_list *timer);
-#else
-# define del_timer_sync(t)		del_timer(t)
-#endif
+extern int timer_delete_sync(struct timer_list *timer);
+extern int timer_delete(struct timer_list *timer);
+extern int timer_shutdown_sync(struct timer_list *timer);
+extern int timer_shutdown(struct timer_list *timer);
+
+/**
+ * del_timer_sync - Delete a pending timer and wait for a running callback
+ * @timer:	The timer to be deleted
+ *
+ * See timer_delete_sync() for detailed explanation.
+ *
+ * Do not use in new code. Use timer_delete_sync() instead.
+ */
+static inline int del_timer_sync(struct timer_list *timer)
+{
+	return timer_delete_sync(timer);
+}
 
 #define del_singleshot_timer_sync(t) del_timer_sync(t)
 
+/**
+ * del_timer - Delete a pending timer
+ * @timer:	The timer to be deleted
+ *
+ * See timer_delete() for detailed explanation.
+ *
+ * Do not use in new code. Use timer_delete() instead.
+ */
+static inline int del_timer(struct timer_list *timer)
+{
+	return timer_delete(timer);
+}
+
 extern void init_timers(void);
 struct hrtimer;
 extern enum hrtimer_restart it_real_fn(struct hrtimer *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/timerqueue.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/timerqueue.h
@@ -35,7 +35,7 @@
 {
 	struct rb_node *leftmost = rb_first_cached(&head->rb_root);
 
-	return rb_entry(leftmost, struct timerqueue_node, node);
+	return rb_entry_safe(leftmost, struct timerqueue_node, node);
 }
 
 static inline void timerqueue_init(struct timerqueue_node *node)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/timex.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/timex.h
@@ -62,6 +62,8 @@
 #include <linux/types.h>
 #include <linux/param.h>
 
+unsigned long random_get_entropy_fallback(void);
+
 #include <asm/timex.h>
 
 #ifndef random_get_entropy
@@ -74,8 +76,14 @@
  *
  * By default we use get_cycles() for this purpose, but individual
  * architectures may override this in their asm/timex.h header file.
+ * If a given arch does not have get_cycles(), then we fallback to
+ * using random_get_entropy_fallback().
  */
-#define random_get_entropy()	get_cycles()
+#ifdef get_cycles
+#define random_get_entropy()	((unsigned long)get_cycles())
+#else
+#define random_get_entropy()	random_get_entropy_fallback()
+#endif
 #endif
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/torture.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/torture.h
@@ -47,6 +47,14 @@
 } while (0)
 void verbose_torout_sleep(void);
 
+#define torture_init_error(firsterr)						\
+({										\
+	int ___firsterr = (firsterr);						\
+										\
+	WARN_ONCE(!IS_MODULE(CONFIG_RCU_TORTURE_TEST) && ___firsterr < 0, "Torture-test initialization failed with error code %d\n", ___firsterr); \
+	___firsterr < 0;								\
+})
+
 /* Definitions for online/offline exerciser. */
 #ifdef CONFIG_HOTPLUG_CPU
 int torture_num_online_cpus(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tpm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tpm.h
@@ -269,6 +269,7 @@
 #define TPM_VID_INTEL    0x8086
 #define TPM_VID_WINBOND  0x1050
 #define TPM_VID_STM      0x104A
+#define TPM_VID_ATML     0x1114
 
 enum tpm_chip_flags {
 	TPM_CHIP_FLAG_TPM2		= BIT(1),
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tpm_eventlog.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tpm_eventlog.h
@@ -157,7 +157,7 @@
  * Return: size of the event on success, 0 on failure
  */
 
-static inline int __calc_tpm2_event_size(struct tcg_pcr_event2_head *event,
+static __always_inline int __calc_tpm2_event_size(struct tcg_pcr_event2_head *event,
 					 struct tcg_pcr_event *event_header,
 					 bool do_mapping)
 {
@@ -198,8 +198,8 @@
 	 * The loop below will unmap these fields if the log is larger than
 	 * one page, so save them here for reference:
 	 */
-	count = READ_ONCE(event->count);
-	event_type = READ_ONCE(event->event_type);
+	count = event->count;
+	event_type = event->event_type;
 
 	/* Verify that it's the log header */
 	if (event_header->pcr_idx != 0 ||
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/trace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/trace.h
@@ -2,8 +2,6 @@
 #ifndef _LINUX_TRACE_H
 #define _LINUX_TRACE_H
 
-#ifdef CONFIG_TRACING
-
 #define TRACE_EXPORT_FUNCTION	BIT(0)
 #define TRACE_EXPORT_EVENT	BIT(1)
 #define TRACE_EXPORT_MARKER	BIT(2)
@@ -28,10 +26,24 @@
 	int flags;
 };
 
+struct trace_array;
+
+#ifdef CONFIG_TRACING
+
 int register_ftrace_export(struct trace_export *export);
 int unregister_ftrace_export(struct trace_export *export);
 
-struct trace_array;
+/**
+ * trace_array_puts - write a constant string into the trace buffer.
+ * @tr:    The trace array to write to
+ * @str:   The constant string to write
+ */
+#define trace_array_puts(tr, str)					\
+	({								\
+		str ? __trace_array_puts(tr, _THIS_IP_, str, strlen(str)) : -1;	\
+	})
+int __trace_array_puts(struct trace_array *tr, unsigned long ip,
+		       const char *str, int size);
 
 void trace_printk_init_buffers(void);
 __printf(3, 4)
@@ -48,6 +60,38 @@
 void osnoise_trace_irq_entry(int id);
 void osnoise_trace_irq_exit(int id, const char *desc);
 
+#else /* CONFIG_TRACING */
+static inline int register_ftrace_export(struct trace_export *export)
+{
+	return -EINVAL;
+}
+static inline int unregister_ftrace_export(struct trace_export *export)
+{
+	return 0;
+}
+static inline void trace_printk_init_buffers(void)
+{
+}
+static inline int trace_array_printk(struct trace_array *tr, unsigned long ip,
+				     const char *fmt, ...)
+{
+	return 0;
+}
+static inline int trace_array_init_printk(struct trace_array *tr)
+{
+	return -EINVAL;
+}
+static inline void trace_array_put(struct trace_array *tr)
+{
+}
+static inline struct trace_array *trace_array_get_by_name(const char *name)
+{
+	return NULL;
+}
+static inline int trace_array_destroy(struct trace_array *tr)
+{
+	return 0;
+}
 #endif	/* CONFIG_TRACING */
 
 #endif	/* _LINUX_TRACE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/trace_events.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/trace_events.h
@@ -91,6 +91,7 @@
 	unsigned int		temp_size;
 	char			*fmt;	/* modified format holder */
 	unsigned int		fmt_size;
+	long			wait_index;
 
 	/* trace_seq for __print_flags() and __print_symbolic() etc. */
 	struct trace_seq	tmp_seq;
@@ -346,7 +347,7 @@
 	struct list_head	list;
 	struct trace_event_class *class;
 	union {
-		char			*name;
+		const char		*name;
 		/* Set TRACE_EVENT_FL_TRACEPOINT flag when using "tp" */
 		struct tracepoint	*tp;
 	};
@@ -467,6 +468,7 @@
 	EVENT_FILE_FL_TRIGGER_COND_BIT,
 	EVENT_FILE_FL_PID_FILTER_BIT,
 	EVENT_FILE_FL_WAS_ENABLED_BIT,
+	EVENT_FILE_FL_FREED_BIT,
 };
 
 extern struct trace_event_file *trace_get_event_file(const char *instance,
@@ -605,6 +607,7 @@
  *  TRIGGER_COND  - When set, one or more triggers has an associated filter
  *  PID_FILTER    - When set, the event is filtered based on pid
  *  WAS_ENABLED   - Set when enabled to know to clear trace on module removal
+ *  FREED         - File descriptor is freed, all fields should be considered invalid
  */
 enum {
 	EVENT_FILE_FL_ENABLED		= (1 << EVENT_FILE_FL_ENABLED_BIT),
@@ -618,6 +621,7 @@
 	EVENT_FILE_FL_TRIGGER_COND	= (1 << EVENT_FILE_FL_TRIGGER_COND_BIT),
 	EVENT_FILE_FL_PID_FILTER	= (1 << EVENT_FILE_FL_PID_FILTER_BIT),
 	EVENT_FILE_FL_WAS_ENABLED	= (1 << EVENT_FILE_FL_WAS_ENABLED_BIT),
+	EVENT_FILE_FL_FREED		= (1 << EVENT_FILE_FL_FREED_BIT),
 };
 
 struct trace_event_file {
@@ -646,6 +650,7 @@
 	 * caching and such. Which is mostly OK ;-)
 	 */
 	unsigned long		flags;
+	atomic_t		ref;	/* ref count for opened files */
 	atomic_t		sm_ref;	/* soft-mode reference counter */
 	atomic_t		tm_ref;	/* trigger-mode reference counter */
 };
@@ -671,9 +676,9 @@
 	}								\
 	early_initcall(trace_init_perf_perm_##name);
 
-#define PERF_MAX_TRACE_SIZE	2048
+#define PERF_MAX_TRACE_SIZE	8192
 
-#define MAX_FILTER_STR_VAL	256	/* Should handle KSYM_SYMBOL_LEN */
+#define MAX_FILTER_STR_VAL	256U	/* Should handle KSYM_SYMBOL_LEN */
 
 enum event_trigger_type {
 	ETT_NONE		= (0),
@@ -796,8 +801,6 @@
 extern int trace_remove_event_call(struct trace_event_call *call);
 extern int trace_event_get_offsets(struct trace_event_call *call);
 
-#define is_signed_type(type)	(((type)(-1)) < (type)1)
-
 int ftrace_set_clr_event(struct trace_array *tr, char *buf, int set);
 int trace_set_clr_event(const char *system, const char *event, int set);
 int trace_array_set_clr_event(struct trace_array *tr, const char *system,
@@ -825,7 +828,6 @@
 struct perf_event;
 
 DECLARE_PER_CPU(struct pt_regs, perf_trace_regs);
-DECLARE_PER_CPU(int, bpf_kprobe_override);
 
 extern int  perf_trace_init(struct perf_event *event);
 extern void perf_trace_destroy(struct perf_event *event);
@@ -845,7 +847,8 @@
 extern void perf_uprobe_destroy(struct perf_event *event);
 extern int bpf_get_uprobe_info(const struct perf_event *event,
 			       u32 *fd_type, const char **filename,
-			       u64 *probe_offset, bool perf_type_tracepoint);
+			       u64 *probe_offset, u64 *probe_addr,
+			       bool perf_type_tracepoint);
 #endif
 extern int  ftrace_profile_set_filter(struct perf_event *event, int event_id,
 				     char *filter_str);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/trace_recursion.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/trace_recursion.h
@@ -116,13 +116,9 @@
 
 static __always_inline int trace_get_context_bit(void)
 {
-	unsigned long pc = preempt_count();
+	unsigned char bit = interrupt_context_level();
 
-	if (!(pc & (NMI_MASK | HARDIRQ_MASK | SOFTIRQ_OFFSET)))
-		return TRACE_CTX_NORMAL;
-	else
-		return pc & NMI_MASK ? TRACE_CTX_NMI :
-			pc & HARDIRQ_MASK ? TRACE_CTX_IRQ : TRACE_CTX_SOFTIRQ;
+	return TRACE_CTX_NORMAL - bit;
 }
 
 #ifdef CONFIG_FTRACE_RECORD_RECURSION
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tracepoint.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tracepoint.h
@@ -231,12 +231,11 @@
  * not add unwanted padding between the beginning of the section and the
  * structure. Force alignment to the same alignment as the section start.
  *
- * When lockdep is enabled, we make sure to always do the RCU portions of
- * the tracepoint code, regardless of whether tracing is on. However,
- * don't check if the condition is false, due to interaction with idle
- * instrumentation. This lets us find RCU issues triggered with tracepoints
- * even when this tracepoint is off. This code has no purpose other than
- * poking RCU a bit.
+ * When lockdep is enabled, we make sure to always test if RCU is
+ * "watching" regardless if the tracepoint is enabled or not. Tracepoints
+ * require RCU to be active, and it should always warn at the tracepoint
+ * site if it is not watching, as it will need to be active when the
+ * tracepoint is enabled.
  */
 #define __DECLARE_TRACE(name, proto, args, cond, data_proto)		\
 	extern int __traceiter_##name(data_proto);			\
@@ -249,9 +248,7 @@
 				TP_ARGS(args),				\
 				TP_CONDITION(cond), 0);			\
 		if (IS_ENABLED(CONFIG_LOCKDEP) && (cond)) {		\
-			rcu_read_lock_sched_notrace();			\
-			rcu_dereference_sched(__tracepoint_##name.funcs);\
-			rcu_read_unlock_sched_notrace();		\
+			WARN_ON_ONCE(!rcu_is_watching());		\
 		}							\
 	}								\
 	__DECLARE_TRACE_RCU(name, PARAMS(proto), PARAMS(args),		\
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/transport_class.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/transport_class.h
@@ -70,8 +70,14 @@
 static inline int
 transport_register_device(struct device *dev)
 {
+	int ret;
+
 	transport_setup_device(dev);
-	return transport_add_device(dev);
+	ret = transport_add_device(dev);
+	if (ret)
+		transport_destroy_device(dev);
+
+	return ret;
 }
 
 static inline void
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/tty_flip.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/tty_flip.h
@@ -17,7 +17,6 @@
 extern int tty_prepare_flip_string(struct tty_port *port,
 		unsigned char **chars, size_t size);
 extern void tty_flip_buffer_push(struct tty_port *port);
-void tty_schedule_flip(struct tty_port *port);
 int __tty_insert_flip_char(struct tty_port *port, unsigned char ch, char flag);
 
 static inline int tty_insert_flip_char(struct tty_port *port,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/u64_stats_sync.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/u64_stats_sync.h
@@ -66,7 +66,7 @@
 #include <linux/seqlock.h>
 
 struct u64_stats_sync {
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
 	seqcount_t	seq;
 #endif
 };
@@ -115,7 +115,7 @@
 }
 #endif
 
-#if BITS_PER_LONG == 32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
 #define u64_stats_init(syncp)	seqcount_init(&(syncp)->seq)
 #else
 static inline void u64_stats_init(struct u64_stats_sync *syncp)
@@ -125,15 +125,19 @@
 
 static inline void u64_stats_update_begin(struct u64_stats_sync *syncp)
 {
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
+	if (IS_ENABLED(CONFIG_PREEMPT_RT))
+		preempt_disable();
 	write_seqcount_begin(&syncp->seq);
 #endif
 }
 
 static inline void u64_stats_update_end(struct u64_stats_sync *syncp)
 {
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
 	write_seqcount_end(&syncp->seq);
+	if (IS_ENABLED(CONFIG_PREEMPT_RT))
+		preempt_enable();
 #endif
 }
 
@@ -142,8 +146,11 @@
 {
 	unsigned long flags = 0;
 
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
-	local_irq_save(flags);
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
+	if (IS_ENABLED(CONFIG_PREEMPT_RT))
+		preempt_disable();
+	else
+		local_irq_save(flags);
 	write_seqcount_begin(&syncp->seq);
 #endif
 	return flags;
@@ -153,15 +160,18 @@
 u64_stats_update_end_irqrestore(struct u64_stats_sync *syncp,
 				unsigned long flags)
 {
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
 	write_seqcount_end(&syncp->seq);
-	local_irq_restore(flags);
+	if (IS_ENABLED(CONFIG_PREEMPT_RT))
+		preempt_enable();
+	else
+		local_irq_restore(flags);
 #endif
 }
 
 static inline unsigned int __u64_stats_fetch_begin(const struct u64_stats_sync *syncp)
 {
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
 	return read_seqcount_begin(&syncp->seq);
 #else
 	return 0;
@@ -170,7 +180,7 @@
 
 static inline unsigned int u64_stats_fetch_begin(const struct u64_stats_sync *syncp)
 {
-#if BITS_PER_LONG==32 && !defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (!defined(CONFIG_SMP) && !defined(CONFIG_PREEMPT_RT))
 	preempt_disable();
 #endif
 	return __u64_stats_fetch_begin(syncp);
@@ -179,7 +189,7 @@
 static inline bool __u64_stats_fetch_retry(const struct u64_stats_sync *syncp,
 					 unsigned int start)
 {
-#if BITS_PER_LONG==32 && defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT))
 	return read_seqcount_retry(&syncp->seq, start);
 #else
 	return false;
@@ -189,7 +199,7 @@
 static inline bool u64_stats_fetch_retry(const struct u64_stats_sync *syncp,
 					 unsigned int start)
 {
-#if BITS_PER_LONG==32 && !defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && (!defined(CONFIG_SMP) && !defined(CONFIG_PREEMPT_RT))
 	preempt_enable();
 #endif
 	return __u64_stats_fetch_retry(syncp, start);
@@ -203,7 +213,9 @@
  */
 static inline unsigned int u64_stats_fetch_begin_irq(const struct u64_stats_sync *syncp)
 {
-#if BITS_PER_LONG==32 && !defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && defined(CONFIG_PREEMPT_RT)
+	preempt_disable();
+#elif BITS_PER_LONG == 32 && !defined(CONFIG_SMP)
 	local_irq_disable();
 #endif
 	return __u64_stats_fetch_begin(syncp);
@@ -212,7 +224,9 @@
 static inline bool u64_stats_fetch_retry_irq(const struct u64_stats_sync *syncp,
 					     unsigned int start)
 {
-#if BITS_PER_LONG==32 && !defined(CONFIG_SMP)
+#if BITS_PER_LONG == 32 && defined(CONFIG_PREEMPT_RT)
+	preempt_enable();
+#elif BITS_PER_LONG == 32 && !defined(CONFIG_SMP)
 	local_irq_enable();
 #endif
 	return __u64_stats_fetch_retry(syncp, start);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/uacce.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/uacce.h
@@ -70,6 +70,7 @@
  * @wait: wait queue head
  * @list: index into uacce queues list
  * @qfrs: pointer of qfr regions
+ * @mutex: protects queue state
  * @state: queue state machine
  * @pasid: pasid associated to the mm
  * @handle: iommu_sva handle returned by iommu_sva_bind_device()
@@ -80,6 +81,7 @@
 	wait_queue_head_t wait;
 	struct list_head list;
 	struct uacce_qfile_region *qfrs[UACCE_MAX_REGION];
+	struct mutex mutex;
 	enum uacce_q_state state;
 	u32 pasid;
 	struct iommu_sva *handle;
@@ -97,9 +99,9 @@
  * @dev_id: id of the uacce device
  * @cdev: cdev of the uacce
  * @dev: dev of the uacce
+ * @mutex: protects uacce operation
  * @priv: private pointer of the uacce
  * @queues: list of queues
- * @queues_lock: lock for queues list
  * @inode: core vfs
  */
 struct uacce_device {
@@ -113,9 +115,9 @@
 	u32 dev_id;
 	struct cdev *cdev;
 	struct device dev;
+	struct mutex mutex;
 	void *priv;
 	struct list_head queues;
-	struct mutex queues_lock;
 	struct inode *inode;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/uaccess.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/uaccess.h
@@ -338,6 +338,10 @@
 	size_t size = min(ksize, usize);
 	size_t rest = max(ksize, usize) - size;
 
+	/* Double check if ksize is larger than a known object size. */
+	if (WARN_ON_ONCE(ksize > __builtin_object_size(dst, 1)))
+		return -E2BIG;
+
 	/* Deal with trailing bytes. */
 	if (usize < ksize) {
 		memset(dst + size, 0, rest);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/udp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/udp.h
@@ -75,6 +75,7 @@
 	 * For encapsulation sockets.
 	 */
 	int (*encap_rcv)(struct sock *sk, struct sk_buff *skb);
+	void (*encap_err_rcv)(struct sock *sk, struct sk_buff *skb, unsigned int udp_offset);
 	int (*encap_err_lookup)(struct sock *sk, struct sk_buff *skb);
 	void (*encap_destroy)(struct sock *sk);
 
@@ -93,7 +94,7 @@
 	int		forward_deficit;
 };
 
-#define UDP_MAX_SEGMENTS	(1 << 6UL)
+#define UDP_MAX_SEGMENTS	(1 << 7UL)
 
 static inline struct udp_sock *udp_sk(const struct sock *sk)
 {
@@ -131,6 +132,24 @@
 	}
 }
 
+DECLARE_STATIC_KEY_FALSE(udp_encap_needed_key);
+#if IS_ENABLED(CONFIG_IPV6)
+DECLARE_STATIC_KEY_FALSE(udpv6_encap_needed_key);
+#endif
+
+static inline bool udp_encap_needed(void)
+{
+	if (static_branch_unlikely(&udp_encap_needed_key))
+		return true;
+
+#if IS_ENABLED(CONFIG_IPV6)
+	if (static_branch_unlikely(&udpv6_encap_needed_key))
+		return true;
+#endif
+
+	return false;
+}
+
 static inline bool udp_unexpected_gso(struct sock *sk, struct sk_buff *skb)
 {
 	if (!skb_is_gso(skb))
@@ -142,6 +161,16 @@
 	if (skb_shinfo(skb)->gso_type & SKB_GSO_FRAGLIST && !udp_sk(sk)->accept_udp_fraglist)
 		return true;
 
+	/* GSO packets lacking the SKB_GSO_UDP_TUNNEL/_CSUM bits might still
+	 * land in a tunnel as the socket check in udp_gro_receive cannot be
+	 * foolproof.
+	 */
+	if (udp_encap_needed() &&
+	    READ_ONCE(udp_sk(sk)->encap_rcv) &&
+	    !(skb_shinfo(skb)->gso_type &
+	      (SKB_GSO_UDP_TUNNEL | SKB_GSO_UDP_TUNNEL_CSUM)))
+		return true;
+
 	return false;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/uio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/uio.h
@@ -35,6 +35,7 @@
 
 struct iov_iter {
 	u8 iter_type;
+	bool nofault;
 	bool data_source;
 	size_t iov_offset;
 	size_t count;
@@ -133,7 +134,8 @@
 				  size_t bytes, struct iov_iter *i);
 void iov_iter_advance(struct iov_iter *i, size_t bytes);
 void iov_iter_revert(struct iov_iter *i, size_t bytes);
-int iov_iter_fault_in_readable(const struct iov_iter *i, size_t bytes);
+size_t fault_in_iov_iter_readable(const struct iov_iter *i, size_t bytes);
+size_t fault_in_iov_iter_writeable(const struct iov_iter *i, size_t bytes);
 size_t iov_iter_single_seg_count(const struct iov_iter *i);
 size_t copy_page_to_iter(struct page *page, size_t offset, size_t bytes,
 			 struct iov_iter *i);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb.h
@@ -279,6 +279,11 @@
 #define USB_MAXINTERFACES	32
 #define USB_MAXIADS		(USB_MAXINTERFACES/2)
 
+bool usb_check_bulk_endpoints(
+		const struct usb_interface *intf, const u8 *ep_addrs);
+bool usb_check_int_endpoints(
+		const struct usb_interface *intf, const u8 *ep_addrs);
+
 /*
  * USB Resume Timer: Every Host controller driver should drive the resume
  * signalling on the bus for the amount of time defined by this macro.
@@ -575,6 +580,7 @@
  * @devaddr: device address, XHCI: assigned by HW, others: same as devnum
  * @can_submit: URBs may be submitted
  * @persist_enabled:  USB_PERSIST enabled for this device
+ * @reset_in_progress: the device is being reset
  * @have_langid: whether string_langid is valid
  * @authorized: policy has said we can use it;
  *	(user space) policy determines if we authorize this device to be
@@ -661,6 +667,7 @@
 
 	unsigned can_submit:1;
 	unsigned persist_enabled:1;
+	unsigned reset_in_progress:1;
 	unsigned have_langid:1;
 	unsigned authorized:1;
 	unsigned authenticated:1;
@@ -688,13 +695,12 @@
 
 	unsigned long active_duration;
 
-#ifdef CONFIG_PM
 	unsigned long connect_time;
 
 	unsigned do_remote_wakeup:1;
 	unsigned reset_resume:1;
 	unsigned port_is_suspended:1;
-#endif
+
 	struct wusb_dev *wusb_dev;
 	int slot_id;
 	struct usb2_lpm_parameters l1_params;
@@ -747,11 +753,14 @@
 extern int usb_acpi_set_power_state(struct usb_device *hdev, int index,
 	bool enable);
 extern bool usb_acpi_power_manageable(struct usb_device *hdev, int index);
+extern int usb_acpi_port_lpm_incapable(struct usb_device *hdev, int index);
 #else
 static inline int usb_acpi_set_power_state(struct usb_device *hdev, int index,
 	bool enable) { return 0; }
 static inline bool usb_acpi_power_manageable(struct usb_device *hdev, int index)
 	{ return true; }
+static inline int usb_acpi_port_lpm_incapable(struct usb_device *hdev, int index)
+	{ return 0; }
 #endif
 
 /* USB autosuspend and autoresume */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/chipidea.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/chipidea.h
@@ -62,6 +62,7 @@
 #define CI_HDRC_REQUIRES_ALIGNED_DMA	BIT(13)
 #define CI_HDRC_IMX_IS_HSIC		BIT(14)
 #define CI_HDRC_PMQOS			BIT(15)
+#define CI_HDRC_PHY_VBUS_CONTROL	BIT(16)
 	enum usb_dr_mode	dr_mode;
 #define CI_HDRC_CONTROLLER_RESET_EVENT		0
 #define CI_HDRC_CONTROLLER_STOPPED_EVENT	1
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/composite.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/composite.h
@@ -163,6 +163,9 @@
  *	GetStatus() request when the recipient is Interface.
  * @func_suspend: callback to be called when
  *	SetFeature(FUNCTION_SUSPEND) is reseived
+ * @func_suspended: Indicates whether the function is in function suspend state.
+ * @func_wakeup_armed: Indicates whether the function is armed by the host for
+ *	wakeup signaling.
  *
  * A single USB function uses one or more interfaces, and should in most
  * cases support operation at both full and high speeds.  Each function is
@@ -233,6 +236,8 @@
 	int			(*get_status)(struct usb_function *);
 	int			(*func_suspend)(struct usb_function *,
 						u8 suspend_opt);
+	bool			func_suspended;
+	bool			func_wakeup_armed;
 	/* private: */
 	/* internals */
 	struct list_head		list;
@@ -254,6 +259,7 @@
 
 int config_ep_by_speed(struct usb_gadget *g, struct usb_function *f,
 			struct usb_ep *_ep);
+int usb_func_wakeup(struct usb_function *func);
 
 #define	MAX_CONFIG_INTERFACES		16	/* arbitrary; max 255 */
 
@@ -426,6 +432,8 @@
 extern int composite_os_desc_req_prepare(struct usb_composite_dev *cdev,
 					 struct usb_ep *ep0);
 void composite_dev_cleanup(struct usb_composite_dev *cdev);
+void check_remote_wakeup_config(struct usb_gadget *g,
+				struct usb_configuration *c);
 
 static inline struct usb_composite_driver *to_cdriver(
 		struct usb_gadget_driver *gdrv)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/gadget.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/gadget.h
@@ -311,6 +311,8 @@
 struct usb_gadget_ops {
 	int	(*get_frame)(struct usb_gadget *);
 	int	(*wakeup)(struct usb_gadget *);
+	int	(*func_wakeup)(struct usb_gadget *gadget, int intf_id);
+	int	(*set_remote_wakeup)(struct usb_gadget *, int set);
 	int	(*set_selfpowered) (struct usb_gadget *, int is_selfpowered);
 	int	(*vbus_session) (struct usb_gadget *, int is_active);
 	int	(*vbus_draw) (struct usb_gadget *, unsigned mA);
@@ -385,6 +387,8 @@
  * @connected: True if gadget is connected.
  * @lpm_capable: If the gadget max_speed is FULL or HIGH, this flag
  *	indicates that it supports LPM as per the LPM ECN & errata.
+ * @wakeup_capable: True if gadget is capable of sending remote wakeup.
+ * @wakeup_armed: True if gadget is armed by the host for remote wakeup.
  * @irq: the interrupt number for device controller.
  *
  * Gadgets have a mostly-portable "gadget driver" implementing device
@@ -445,6 +449,8 @@
 	unsigned			deactivated:1;
 	unsigned			connected:1;
 	unsigned			lpm_capable:1;
+	unsigned			wakeup_capable:1;
+	unsigned			wakeup_armed:1;
 	int				irq;
 };
 #define work_to_gadget(w)	(container_of((w), struct usb_gadget, work))
@@ -600,6 +606,7 @@
 #if IS_ENABLED(CONFIG_USB_GADGET)
 int usb_gadget_frame_number(struct usb_gadget *gadget);
 int usb_gadget_wakeup(struct usb_gadget *gadget);
+int usb_gadget_set_remote_wakeup(struct usb_gadget *gadget, int set);
 int usb_gadget_set_selfpowered(struct usb_gadget *gadget);
 int usb_gadget_clear_selfpowered(struct usb_gadget *gadget);
 int usb_gadget_vbus_connect(struct usb_gadget *gadget);
@@ -615,6 +622,8 @@
 { return 0; }
 static inline int usb_gadget_wakeup(struct usb_gadget *gadget)
 { return 0; }
+static inline int usb_gadget_set_remote_wakeup(struct usb_gadget *gadget, int set)
+{ return 0; }
 static inline int usb_gadget_set_selfpowered(struct usb_gadget *gadget)
 { return 0; }
 static inline int usb_gadget_clear_selfpowered(struct usb_gadget *gadget)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/hcd.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/hcd.h
@@ -66,6 +66,7 @@
 
 struct giveback_urb_bh {
 	bool running;
+	bool high_prio;
 	spinlock_t lock;
 	struct list_head  head;
 	struct tasklet_struct bh;
@@ -384,8 +385,9 @@
 		 * or bandwidth constraints.
 		 */
 	void	(*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
-		/* Returns the hardware-chosen device address */
-	int	(*address_device)(struct usb_hcd *, struct usb_device *udev);
+		/* Set the hardware-chosen device address */
+	int	(*address_device)(struct usb_hcd *, struct usb_device *udev,
+				  unsigned int timeout_ms);
 		/* prepares the hardware to send commands to the device */
 	int	(*enable_device)(struct usb_hcd *, struct usb_device *udev);
 		/* Notifies the HCD after a hub descriptor is fetched.
@@ -499,9 +501,7 @@
 
 extern int usb_hcd_amd_remote_wakeup_quirk(struct pci_dev *dev);
 
-#ifdef CONFIG_PM
 extern const struct dev_pm_ops usb_hcd_pci_pm_ops;
-#endif
 #endif /* CONFIG_USB_PCI */
 
 /* pci-ish (pdev null is ok) buffer alloc/mapping support */
@@ -514,6 +514,11 @@
 void hcd_buffer_free(struct usb_bus *bus, size_t size,
 	void *addr, dma_addr_t dma);
 
+void *hcd_buffer_alloc_pages(struct usb_hcd *hcd,
+		size_t size, gfp_t mem_flags, dma_addr_t *dma);
+void hcd_buffer_free_pages(struct usb_hcd *hcd,
+		size_t size, void *addr, dma_addr_t dma);
+
 /* generic bus glue, needed for host controllers that don't use PCI */
 extern irqreturn_t usb_hcd_irq(int irq, void *__hcd);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/r8152.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/r8152.h
@@ -29,6 +29,8 @@
 #define VENDOR_ID_LINKSYS		0x13b1
 #define VENDOR_ID_NVIDIA		0x0955
 #define VENDOR_ID_TPLINK		0x2357
+#define VENDOR_ID_DLINK			0x2001
+#define VENDOR_ID_ASUS			0x0b05
 
 #if IS_REACHABLE(CONFIG_USB_RTL8152)
 extern u8 rtl8152_get_version(struct usb_interface *intf);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/role.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/role.h
@@ -92,6 +92,12 @@
 static inline void usb_role_switch_put(struct usb_role_switch *sw) { }
 
 static inline struct usb_role_switch *
+usb_role_switch_find_by_fwnode(const struct fwnode_handle *fwnode)
+{
+	return NULL;
+}
+
+static inline struct usb_role_switch *
 usb_role_switch_register(struct device *parent,
 			 const struct usb_role_switch_desc *desc)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/tcpci.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/tcpci.h
@@ -0,0 +1,211 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2015-2017 Google, Inc
+ *
+ * USB Type-C Port Controller Interface.
+ */
+
+#ifndef __LINUX_USB_TCPCI_H
+#define __LINUX_USB_TCPCI_H
+
+#include <linux/usb/typec.h>
+#include <linux/usb/tcpm.h>
+
+#define TCPC_VENDOR_ID			0x0
+#define TCPC_PRODUCT_ID			0x2
+#define TCPC_BCD_DEV			0x4
+#define TCPC_TC_REV			0x6
+#define TCPC_PD_REV			0x8
+#define TCPC_PD_INT_REV			0xa
+
+#define TCPC_ALERT			0x10
+#define TCPC_ALERT_EXTND		BIT(14)
+#define TCPC_ALERT_EXTENDED_STATUS	BIT(13)
+#define TCPC_ALERT_VBUS_DISCNCT		BIT(11)
+#define TCPC_ALERT_RX_BUF_OVF		BIT(10)
+#define TCPC_ALERT_FAULT		BIT(9)
+#define TCPC_ALERT_V_ALARM_LO		BIT(8)
+#define TCPC_ALERT_V_ALARM_HI		BIT(7)
+#define TCPC_ALERT_TX_SUCCESS		BIT(6)
+#define TCPC_ALERT_TX_DISCARDED		BIT(5)
+#define TCPC_ALERT_TX_FAILED		BIT(4)
+#define TCPC_ALERT_RX_HARD_RST		BIT(3)
+#define TCPC_ALERT_RX_STATUS		BIT(2)
+#define TCPC_ALERT_POWER_STATUS		BIT(1)
+#define TCPC_ALERT_CC_STATUS		BIT(0)
+
+#define TCPC_ALERT_MASK			0x12
+#define TCPC_POWER_STATUS_MASK		0x14
+#define TCPC_FAULT_STATUS_MASK		0x15
+
+#define TCPC_EXTENDED_STATUS_MASK		0x16
+#define TCPC_EXTENDED_STATUS_MASK_VSAFE0V	BIT(0)
+
+#define TCPC_ALERT_EXTENDED_MASK	0x17
+#define TCPC_SINK_FAST_ROLE_SWAP	BIT(0)
+
+#define TCPC_CONFIG_STD_OUTPUT		0x18
+
+#define TCPC_TCPC_CTRL			0x19
+#define TCPC_TCPC_CTRL_ORIENTATION	BIT(0)
+#define PLUG_ORNT_CC1			0
+#define PLUG_ORNT_CC2			1
+#define TCPC_TCPC_CTRL_BIST_TM		BIT(1)
+#define TCPC_TCPC_CTRL_EN_LK4CONN_ALRT	BIT(6)
+
+#define TCPC_EXTENDED_STATUS		0x20
+#define TCPC_EXTENDED_STATUS_VSAFE0V	BIT(0)
+
+#define TCPC_ROLE_CTRL			0x1a
+#define TCPC_ROLE_CTRL_DRP		BIT(6)
+#define TCPC_ROLE_CTRL_RP_VAL_SHIFT	4
+#define TCPC_ROLE_CTRL_RP_VAL_MASK	0x3
+#define TCPC_ROLE_CTRL_RP_VAL_DEF	0x0
+#define TCPC_ROLE_CTRL_RP_VAL_1_5	0x1
+#define TCPC_ROLE_CTRL_RP_VAL_3_0	0x2
+#define TCPC_ROLE_CTRL_CC2_SHIFT	2
+#define TCPC_ROLE_CTRL_CC2_MASK		0x3
+#define TCPC_ROLE_CTRL_CC1_SHIFT	0
+#define TCPC_ROLE_CTRL_CC1_MASK		0x3
+#define TCPC_ROLE_CTRL_CC_RA		0x0
+#define TCPC_ROLE_CTRL_CC_RP		0x1
+#define TCPC_ROLE_CTRL_CC_RD		0x2
+#define TCPC_ROLE_CTRL_CC_OPEN		0x3
+
+#define TCPC_FAULT_CTRL			0x1b
+
+#define TCPC_POWER_CTRL			0x1c
+#define TCPC_POWER_CTRL_VCONN_ENABLE	BIT(0)
+#define TCPC_POWER_CTRL_BLEED_DISCHARGE	BIT(3)
+#define TCPC_POWER_CTRL_AUTO_DISCHARGE	BIT(4)
+#define TCPC_DIS_VOLT_ALRM		BIT(5)
+#define TCPC_POWER_CTRL_VBUS_VOLT_MON	BIT(6)
+#define TCPC_FAST_ROLE_SWAP_EN		BIT(7)
+
+#define TCPC_CC_STATUS			0x1d
+#define TCPC_CC_STATUS_TOGGLING		BIT(5)
+#define TCPC_CC_STATUS_TERM		BIT(4)
+#define TCPC_CC_STATUS_TERM_RP		0
+#define TCPC_CC_STATUS_TERM_RD		1
+#define TCPC_CC_STATE_SRC_OPEN		0
+#define TCPC_CC_STATUS_CC2_SHIFT	2
+#define TCPC_CC_STATUS_CC2_MASK		0x3
+#define TCPC_CC_STATUS_CC1_SHIFT	0
+#define TCPC_CC_STATUS_CC1_MASK		0x3
+
+#define TCPC_POWER_STATUS		0x1e
+#define TCPC_POWER_STATUS_DBG_ACC_CON	BIT(7)
+#define TCPC_POWER_STATUS_UNINIT	BIT(6)
+#define TCPC_POWER_STATUS_SOURCING_VBUS	BIT(4)
+#define TCPC_POWER_STATUS_VBUS_DET	BIT(3)
+#define TCPC_POWER_STATUS_VBUS_PRES	BIT(2)
+#define TCPC_POWER_STATUS_VCONN_PRES	BIT(1)
+#define TCPC_POWER_STATUS_SINKING_VBUS	BIT(0)
+
+#define TCPC_FAULT_STATUS		0x1f
+#define TCPC_FAULT_STATUS_ALL_REG_RST_TO_DEFAULT BIT(7)
+
+#define TCPC_ALERT_EXTENDED		0x21
+
+#define TCPC_COMMAND			0x23
+#define TCPC_CMD_WAKE_I2C		0x11
+#define TCPC_CMD_DISABLE_VBUS_DETECT	0x22
+#define TCPC_CMD_ENABLE_VBUS_DETECT	0x33
+#define TCPC_CMD_DISABLE_SINK_VBUS	0x44
+#define TCPC_CMD_SINK_VBUS		0x55
+#define TCPC_CMD_DISABLE_SRC_VBUS	0x66
+#define TCPC_CMD_SRC_VBUS_DEFAULT	0x77
+#define TCPC_CMD_SRC_VBUS_HIGH		0x88
+#define TCPC_CMD_LOOK4CONNECTION	0x99
+#define TCPC_CMD_RXONEMORE		0xAA
+#define TCPC_CMD_I2C_IDLE		0xFF
+
+#define TCPC_DEV_CAP_1			0x24
+#define TCPC_DEV_CAP_2			0x26
+#define TCPC_STD_INPUT_CAP		0x28
+#define TCPC_STD_OUTPUT_CAP		0x29
+
+#define TCPC_MSG_HDR_INFO		0x2e
+#define TCPC_MSG_HDR_INFO_DATA_ROLE	BIT(3)
+#define TCPC_MSG_HDR_INFO_PWR_ROLE	BIT(0)
+#define TCPC_MSG_HDR_INFO_REV_SHIFT	1
+#define TCPC_MSG_HDR_INFO_REV_MASK	0x3
+
+#define TCPC_RX_DETECT			0x2f
+#define TCPC_RX_DETECT_HARD_RESET	BIT(5)
+#define TCPC_RX_DETECT_SOP		BIT(0)
+#define TCPC_RX_DETECT_SOP1		BIT(1)
+#define TCPC_RX_DETECT_SOP2		BIT(2)
+#define TCPC_RX_DETECT_DBG1		BIT(3)
+#define TCPC_RX_DETECT_DBG2		BIT(4)
+
+#define TCPC_RX_BYTE_CNT		0x30
+#define TCPC_RX_BUF_FRAME_TYPE		0x31
+#define TCPC_RX_BUF_FRAME_TYPE_SOP	0
+#define TCPC_RX_HDR			0x32
+#define TCPC_RX_DATA			0x34 /* through 0x4f */
+
+#define TCPC_TRANSMIT			0x50
+#define TCPC_TRANSMIT_RETRY_SHIFT	4
+#define TCPC_TRANSMIT_RETRY_MASK	0x3
+#define TCPC_TRANSMIT_TYPE_SHIFT	0
+#define TCPC_TRANSMIT_TYPE_MASK		0x7
+
+#define TCPC_TX_BYTE_CNT		0x51
+#define TCPC_TX_HDR			0x52
+#define TCPC_TX_DATA			0x54 /* through 0x6f */
+
+#define TCPC_VBUS_VOLTAGE			0x70
+#define TCPC_VBUS_VOLTAGE_MASK			0x3ff
+#define TCPC_VBUS_VOLTAGE_LSB_MV		25
+#define TCPC_VBUS_SINK_DISCONNECT_THRESH	0x72
+#define TCPC_VBUS_SINK_DISCONNECT_THRESH_LSB_MV	25
+#define TCPC_VBUS_SINK_DISCONNECT_THRESH_MAX	0x3ff
+#define TCPC_VBUS_STOP_DISCHARGE_THRESH		0x74
+#define TCPC_VBUS_VOLTAGE_ALARM_HI_CFG		0x76
+#define TCPC_VBUS_VOLTAGE_ALARM_LO_CFG		0x78
+
+/* I2C_WRITE_BYTE_COUNT + 1 when TX_BUF_BYTE_x is only accessible I2C_WRITE_BYTE_COUNT */
+#define TCPC_TRANSMIT_BUFFER_MAX_LEN		31
+
+struct tcpci;
+
+/*
+ * @TX_BUF_BYTE_x_hidden:
+ *		optional; Set when TX_BUF_BYTE_x can only be accessed through I2C_WRITE_BYTE_COUNT.
+ * @frs_sourcing_vbus:
+ *		Optional; Callback to perform chip specific operations when FRS
+ *		is sourcing vbus.
+ * @auto_discharge_disconnect:
+ *		Optional; Enables TCPC to autonously discharge vbus on disconnect.
+ * @vbus_vsafe0v:
+ *		optional; Set when TCPC can detect whether vbus is at VSAFE0V.
+ * @set_partner_usb_comm_capable:
+ *		Optional; The USB Communications Capable bit indicates if port
+ *		partner is capable of communication over the USB data lines
+ *		(e.g. D+/- or SS Tx/Rx). Called to notify the status of the bit.
+ */
+struct tcpci_data {
+	struct regmap *regmap;
+	unsigned char TX_BUF_BYTE_x_hidden:1;
+	unsigned char auto_discharge_disconnect:1;
+	unsigned char vbus_vsafe0v:1;
+
+	int (*init)(struct tcpci *tcpci, struct tcpci_data *data);
+	int (*set_vconn)(struct tcpci *tcpci, struct tcpci_data *data,
+			 bool enable);
+	int (*start_drp_toggling)(struct tcpci *tcpci, struct tcpci_data *data,
+				  enum typec_cc_status cc);
+	int (*set_vbus)(struct tcpci *tcpci, struct tcpci_data *data, bool source, bool sink);
+	void (*frs_sourcing_vbus)(struct tcpci *tcpci, struct tcpci_data *data);
+	void (*set_partner_usb_comm_capable)(struct tcpci *tcpci, struct tcpci_data *data,
+					     bool capable);
+};
+
+struct tcpci *tcpci_register_port(struct device *dev, struct tcpci_data *data);
+void tcpci_unregister_port(struct tcpci *tcpci);
+irqreturn_t tcpci_irq(struct tcpci *tcpci);
+
+struct tcpm_port;
+struct tcpm_port *tcpci_get_tcpm_port(struct tcpci *tcpci);
+#endif /* __LINUX_USB_TCPCI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/tcpm.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/tcpm.h
@@ -145,7 +145,8 @@
 	void (*frs_sourcing_vbus)(struct tcpc_dev *dev);
 	int (*enable_auto_vbus_discharge)(struct tcpc_dev *dev, bool enable);
 	int (*set_auto_vbus_discharge_threshold)(struct tcpc_dev *dev, enum typec_pwr_opmode mode,
-						 bool pps_active, u32 requested_vbus_voltage);
+						 bool pps_active, u32 requested_vbus_voltage,
+						 u32 pps_apdo_min_voltage);
 	bool (*is_vbus_vsafe0v)(struct tcpc_dev *dev);
 	void (*set_partner_usb_comm_capable)(struct tcpc_dev *dev, bool enable);
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/typec.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/typec.h
@@ -295,6 +295,9 @@
 
 void *typec_get_drvdata(struct typec_port *port);
 
+int typec_get_fw_cap(struct typec_capability *cap,
+		     struct fwnode_handle *fwnode);
+
 int typec_find_pwr_opmode(const char *name);
 int typec_find_orientation(const char *name);
 int typec_find_port_power_role(const char *name);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/typec_altmode.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/typec_altmode.h
@@ -67,7 +67,7 @@
 
 int typec_altmode_enter(struct typec_altmode *altmode, u32 *vdo);
 int typec_altmode_exit(struct typec_altmode *altmode);
-void typec_altmode_attention(struct typec_altmode *altmode, u32 vdo);
+int typec_altmode_attention(struct typec_altmode *altmode, u32 vdo);
 int typec_altmode_vdm(struct typec_altmode *altmode,
 		      const u32 header, const u32 *vdo, int count);
 int typec_altmode_notify(struct typec_altmode *altmode, unsigned long conf,
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/typec_dp.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/typec_dp.h
@@ -73,6 +73,11 @@
 #define DP_CAP_USB			BIT(7)
 #define DP_CAP_DFP_D_PIN_ASSIGN(_cap_)	(((_cap_) & GENMASK(15, 8)) >> 8)
 #define DP_CAP_UFP_D_PIN_ASSIGN(_cap_)	(((_cap_) & GENMASK(23, 16)) >> 16)
+/* Get pin assignment taking plug & receptacle into consideration */
+#define DP_CAP_PIN_ASSIGN_UFP_D(_cap_) ((_cap_ & DP_CAP_RECEPTACLE) ? \
+			DP_CAP_UFP_D_PIN_ASSIGN(_cap_) : DP_CAP_DFP_D_PIN_ASSIGN(_cap_))
+#define DP_CAP_PIN_ASSIGN_DFP_D(_cap_) ((_cap_ & DP_CAP_RECEPTACLE) ? \
+			DP_CAP_DFP_D_PIN_ASSIGN(_cap_) : DP_CAP_UFP_D_PIN_ASSIGN(_cap_))
 
 /* DisplayPort Status Update VDO bits */
 #define DP_STATUS_CONNECTION(_status_)	((_status_) & 3)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/usb/usbnet.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/usb/usbnet.h
@@ -84,8 +84,23 @@
 #		define EVENT_LINK_CHANGE	11
 #		define EVENT_SET_RX_MODE	12
 #		define EVENT_NO_IP_ALIGN	13
+/* This one is special, as it indicates that the device is going away
+ * there are cyclic dependencies between tasklet, timer and bh
+ * that must be broken
+ */
+#		define EVENT_UNPLUG		31
 };
 
+static inline bool usbnet_going_away(struct usbnet *ubn)
+{
+	return test_bit(EVENT_UNPLUG, &ubn->flags);
+}
+
+static inline void usbnet_mark_going_away(struct usbnet *ubn)
+{
+	set_bit(EVENT_UNPLUG, &ubn->flags);
+}
+
 static inline struct usb_driver *driver_of(struct usb_interface *intf)
 {
 	return to_usb_driver(intf->dev.driver);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/user_namespace.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/user_namespace.h
@@ -170,6 +170,8 @@
 		       const struct user_namespace *child);
 extern bool current_in_userns(const struct user_namespace *target_ns);
 struct ns_common *ns_get_owner(struct ns_common *ns);
+
+extern int unprivileged_userns_clone;
 #else
 
 static inline struct user_namespace *get_user_ns(struct user_namespace *ns)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/util_macros.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/util_macros.h
@@ -2,19 +2,6 @@
 #ifndef _LINUX_HELPER_MACROS_H_
 #define _LINUX_HELPER_MACROS_H_
 
-#define __find_closest(x, a, as, op)					\
-({									\
-	typeof(as) __fc_i, __fc_as = (as) - 1;				\
-	typeof(x) __fc_x = (x);						\
-	typeof(*a) const *__fc_a = (a);					\
-	for (__fc_i = 0; __fc_i < __fc_as; __fc_i++) {			\
-		if (__fc_x op DIV_ROUND_CLOSEST(__fc_a[__fc_i] +	\
-						__fc_a[__fc_i + 1], 2))	\
-			break;						\
-	}								\
-	(__fc_i);							\
-})
-
 /**
  * find_closest - locate the closest element in a sorted array
  * @x: The reference value.
@@ -23,8 +10,27 @@
  * @as: Size of 'a'.
  *
  * Returns the index of the element closest to 'x'.
+ * Note: If using an array of negative numbers (or mixed positive numbers),
+ *       then be sure that 'x' is of a signed-type to get good results.
  */
-#define find_closest(x, a, as) __find_closest(x, a, as, <=)
+#define find_closest(x, a, as)						\
+({									\
+	typeof(as) __fc_i, __fc_as = (as) - 1;				\
+	long __fc_mid_x, __fc_x = (x);					\
+	long __fc_left, __fc_right;					\
+	typeof(*a) const *__fc_a = (a);					\
+	for (__fc_i = 0; __fc_i < __fc_as; __fc_i++) {			\
+		__fc_mid_x = (__fc_a[__fc_i] + __fc_a[__fc_i + 1]) / 2;	\
+		if (__fc_x <= __fc_mid_x) {				\
+			__fc_left = __fc_x - __fc_a[__fc_i];		\
+			__fc_right = __fc_a[__fc_i + 1] - __fc_x;	\
+			if (__fc_right < __fc_left)			\
+				__fc_i++;				\
+			break;						\
+		}							\
+	}								\
+	(__fc_i);							\
+})
 
 /**
  * find_closest_descending - locate the closest element in a sorted array
@@ -34,8 +40,38 @@
  * @as: Size of 'a'.
  *
  * Similar to find_closest() but 'a' is expected to be sorted in descending
- * order.
+ * order. The iteration is done in reverse order, so that the comparison
+ * of '__fc_right' & '__fc_left' also works for unsigned numbers.
+ */
+#define find_closest_descending(x, a, as)				\
+({									\
+	typeof(as) __fc_i, __fc_as = (as) - 1;				\
+	long __fc_mid_x, __fc_x = (x);					\
+	long __fc_left, __fc_right;					\
+	typeof(*a) const *__fc_a = (a);					\
+	for (__fc_i = __fc_as; __fc_i >= 1; __fc_i--) {			\
+		__fc_mid_x = (__fc_a[__fc_i] + __fc_a[__fc_i - 1]) / 2;	\
+		if (__fc_x <= __fc_mid_x) {				\
+			__fc_left = __fc_x - __fc_a[__fc_i];		\
+			__fc_right = __fc_a[__fc_i - 1] - __fc_x;	\
+			if (__fc_right < __fc_left)			\
+				__fc_i--;				\
+			break;						\
+		}							\
+	}								\
+	(__fc_i);							\
+})
+
+/**
+ * is_insidevar - check if the @ptr points inside the @var memory range.
+ * @ptr:	the pointer to a memory address.
+ * @var:	the variable which address and size identify the memory range.
+ *
+ * Evaluates to true if the address in @ptr lies within the memory
+ * range allocated to @var.
  */
-#define find_closest_descending(x, a, as) __find_closest(x, a, as, >=)
+#define is_insidevar(ptr, var)						\
+	((uintptr_t)(ptr) >= (uintptr_t)(var) &&			\
+	 (uintptr_t)(ptr) <  (uintptr_t)(var) + sizeof(var))
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vdpa.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vdpa.h
@@ -11,10 +11,16 @@
  * struct vdpa_calllback - vDPA callback definition.
  * @callback: interrupt callback function
  * @private: the data passed to the callback function
+ * @trigger: the eventfd for the callback (Optional).
+ *           When it is set, the vDPA driver must guarantee that
+ *           signaling it is functional equivalent to triggering
+ *           the callback. Then vDPA parent can signal it directly
+ *           instead of triggering the callback.
  */
 struct vdpa_callback {
 	irqreturn_t (*callback)(void *data);
 	void *private;
+	struct eventfd_ctx *trigger;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vfio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vfio.h
@@ -243,6 +243,7 @@
 	wait_queue_entry_t		wait;
 	poll_table		pt;
 	struct work_struct	shutdown;
+	struct work_struct	flush_inject;
 	struct virqfd		**pvirqfd;
 };
 
@@ -251,5 +252,6 @@
 			      void (*thread)(void *, void *),
 			      void *data, struct virqfd **pvirqfd, int fd);
 extern void vfio_virqfd_disable(struct virqfd **pvirqfd);
+void vfio_virqfd_flush_thread(struct virqfd **pvirqfd);
 
 #endif /* VFIO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vfio_pci_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vfio_pci_core.h
@@ -133,6 +133,8 @@
 	struct mutex		ioeventfds_lock;
 	struct list_head	ioeventfds_list;
 	struct vfio_pci_vf_token	*vf_token;
+	struct list_head		sriov_pfs_item;
+	struct vfio_pci_core_device	*sriov_pf_core_dev;
 	struct notifier_block	nb;
 	struct mutex		vma_lock;
 	struct list_head	vma_list;
@@ -159,8 +161,17 @@
 extern ssize_t vfio_pci_bar_rw(struct vfio_pci_core_device *vdev, char __user *buf,
 			       size_t count, loff_t *ppos, bool iswrite);
 
+#ifdef CONFIG_VFIO_PCI_VGA
 extern ssize_t vfio_pci_vga_rw(struct vfio_pci_core_device *vdev, char __user *buf,
 			       size_t count, loff_t *ppos, bool iswrite);
+#else
+static inline ssize_t vfio_pci_vga_rw(struct vfio_pci_core_device *vdev,
+				      char __user *buf, size_t count,
+				      loff_t *ppos, bool iswrite)
+{
+	return -EINVAL;
+}
+#endif
 
 extern long vfio_pci_ioeventfd(struct vfio_pci_core_device *vdev, loff_t offset,
 			       uint64_t data, int count, int fd);
@@ -195,15 +206,25 @@
 }
 #endif
 
-#ifdef CONFIG_S390
+#ifdef CONFIG_VFIO_PCI_ZDEV_KVM
 extern int vfio_pci_info_zdev_add_caps(struct vfio_pci_core_device *vdev,
 				       struct vfio_info_cap *caps);
+int vfio_pci_zdev_open_device(struct vfio_pci_core_device *vdev);
+void vfio_pci_zdev_close_device(struct vfio_pci_core_device *vdev);
 #else
 static inline int vfio_pci_info_zdev_add_caps(struct vfio_pci_core_device *vdev,
 					      struct vfio_info_cap *caps)
 {
 	return -ENODEV;
 }
+
+static inline int vfio_pci_zdev_open_device(struct vfio_pci_core_device *vdev)
+{
+	return 0;
+}
+
+static inline void vfio_pci_zdev_close_device(struct vfio_pci_core_device *vdev)
+{}
 #endif
 
 /* Will be exported for vfio pci drivers usage */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/virtio.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/virtio.h
@@ -133,7 +133,6 @@
 void virtio_break_device(struct virtio_device *dev);
 
 void virtio_config_changed(struct virtio_device *dev);
-int virtio_finalize_features(struct virtio_device *dev);
 #ifdef CONFIG_PM_SLEEP
 int virtio_device_freeze(struct virtio_device *dev);
 int virtio_device_restore(struct virtio_device *dev);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/virtio_config.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/virtio_config.h
@@ -62,8 +62,9 @@
  *	Returns the first 64 feature bits (all we currently need).
  * @finalize_features: confirm what device features we'll be using.
  *	vdev: the virtio_device
- *	This gives the final feature bits for the device: it can change
+ *	This sends the driver feature bits to the device: it can change
  *	the dev->feature bits if it wants.
+ * Note: despite the name this can be called any number of times.
  *	Returns 0 on success or error status
  * @bus_name: return the bus name associated with the device (optional)
  *	vdev: the virtio_device
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/virtio_net.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/virtio_net.h
@@ -3,13 +3,31 @@
 #define _LINUX_VIRTIO_NET_H
 
 #include <linux/if_vlan.h>
+#include <linux/udp.h>
 #include <uapi/linux/tcp.h>
-#include <uapi/linux/udp.h>
 #include <uapi/linux/virtio_net.h>
 
+static inline bool virtio_net_hdr_match_proto(__be16 protocol, __u8 gso_type)
+{
+	switch (gso_type & ~VIRTIO_NET_HDR_GSO_ECN) {
+	case VIRTIO_NET_HDR_GSO_TCPV4:
+		return protocol == cpu_to_be16(ETH_P_IP);
+	case VIRTIO_NET_HDR_GSO_TCPV6:
+		return protocol == cpu_to_be16(ETH_P_IPV6);
+	case VIRTIO_NET_HDR_GSO_UDP:
+		return protocol == cpu_to_be16(ETH_P_IP) ||
+		       protocol == cpu_to_be16(ETH_P_IPV6);
+	default:
+		return false;
+	}
+}
+
 static inline int virtio_net_hdr_set_proto(struct sk_buff *skb,
 					   const struct virtio_net_hdr *hdr)
 {
+	if (skb->protocol)
+		return 0;
+
 	switch (hdr->gso_type & ~VIRTIO_NET_HDR_GSO_ECN) {
 	case VIRTIO_NET_HDR_GSO_TCPV4:
 	case VIRTIO_NET_HDR_GSO_UDP:
@@ -88,9 +106,12 @@
 			if (!skb->protocol) {
 				__be16 protocol = dev_parse_header_protocol(skb);
 
-				virtio_net_hdr_set_proto(skb, hdr);
-				if (protocol && protocol != skb->protocol)
+				if (!protocol)
+					virtio_net_hdr_set_proto(skb, hdr);
+				else if (!virtio_net_hdr_match_proto(protocol, hdr->gso_type))
 					return -EINVAL;
+				else
+					skb->protocol = protocol;
 			}
 retry:
 			if (!skb_flow_dissect_flow_keys_basic(NULL, skb, &keys,
@@ -120,10 +141,38 @@
 
 	if (hdr->gso_type != VIRTIO_NET_HDR_GSO_NONE) {
 		u16 gso_size = __virtio16_to_cpu(little_endian, hdr->gso_size);
+		unsigned int nh_off = p_off;
 		struct skb_shared_info *shinfo = skb_shinfo(skb);
 
+		switch (gso_type & ~SKB_GSO_TCP_ECN) {
+		case SKB_GSO_UDP:
+			/* UFO may not include transport header in gso_size. */
+			nh_off -= thlen;
+			break;
+		case SKB_GSO_UDP_L4:
+			if (!(hdr->flags & VIRTIO_NET_HDR_F_NEEDS_CSUM))
+				return -EINVAL;
+			if (skb->csum_offset != offsetof(struct udphdr, check))
+				return -EINVAL;
+			if (skb->len - p_off > gso_size * UDP_MAX_SEGMENTS)
+				return -EINVAL;
+			if (gso_type != SKB_GSO_UDP_L4)
+				return -EINVAL;
+			break;
+		case SKB_GSO_TCPV4:
+		case SKB_GSO_TCPV6:
+			if (skb->ip_summed == CHECKSUM_PARTIAL &&
+			    skb->csum_offset != offsetof(struct tcphdr, check))
+				return -EINVAL;
+			break;
+		}
+
+		/* Kernel has a special handling for GSO_BY_FRAGS. */
+		if (gso_size == GSO_BY_FRAGS)
+			return -EINVAL;
+
 		/* Too small packets are not really GSO ones. */
-		if (skb->len - p_off > gso_size) {
+		if (skb->len - nh_off > gso_size) {
 			shinfo->gso_size = gso_size;
 			shinfo->gso_type = gso_type;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vmalloc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vmalloc.h
@@ -28,6 +28,13 @@
 #define VM_MAP_PUT_PAGES	0x00000200	/* put pages and free array in vfree */
 #define VM_NO_HUGE_VMAP		0x00000400	/* force PAGE_SIZE pte mapping */
 
+#if (defined(CONFIG_KASAN_GENERIC) || defined(CONFIG_KASAN_SW_TAGS)) && \
+	!defined(CONFIG_KASAN_VMALLOC)
+#define VM_DEFER_KMEMLEAK	0x00000800	/* defer kmemleak object creation */
+#else
+#define VM_DEFER_KMEMLEAK	0
+#endif
+
 /*
  * VM_KASAN is used slightly differently depending on CONFIG_KASAN_VMALLOC.
  *
@@ -152,6 +159,11 @@
 		int node, const void *caller);
 void *vmalloc_no_huge(unsigned long size);
 
+extern void *__vmalloc_array(size_t n, size_t size, gfp_t flags) __alloc_size(1, 2);
+extern void *vmalloc_array(size_t n, size_t size) __alloc_size(1, 2);
+extern void *__vcalloc(size_t n, size_t size, gfp_t flags) __alloc_size(1, 2);
+extern void *vcalloc(size_t n, size_t size) __alloc_size(1, 2);
+
 extern void vfree(const void *addr);
 extern void vfree_atomic(const void *addr);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vmstat.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vmstat.h
@@ -447,7 +447,7 @@
 
 static inline const char *lru_list_name(enum lru_list lru)
 {
-	return node_stat_name(NR_LRU_BASE + lru) + 3; // skip "nr_"
+	return node_stat_name(NR_LRU_BASE + (enum node_stat_item)lru) + 3; // skip "nr_"
 }
 
 static inline const char *writeback_stat_name(enum writeback_stat_item item)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vmw_vmci_defs.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vmw_vmci_defs.h
@@ -12,15 +12,20 @@
 #include <linux/bits.h>
 
 /* Register offsets. */
-#define VMCI_STATUS_ADDR      0x00
-#define VMCI_CONTROL_ADDR     0x04
-#define VMCI_ICR_ADDR	      0x08
-#define VMCI_IMR_ADDR         0x0c
-#define VMCI_DATA_OUT_ADDR    0x10
-#define VMCI_DATA_IN_ADDR     0x14
-#define VMCI_CAPS_ADDR        0x18
-#define VMCI_RESULT_LOW_ADDR  0x1c
-#define VMCI_RESULT_HIGH_ADDR 0x20
+#define VMCI_STATUS_ADDR        0x00
+#define VMCI_CONTROL_ADDR       0x04
+#define VMCI_ICR_ADDR           0x08
+#define VMCI_IMR_ADDR           0x0c
+#define VMCI_DATA_OUT_ADDR      0x10
+#define VMCI_DATA_IN_ADDR       0x14
+#define VMCI_CAPS_ADDR          0x18
+#define VMCI_RESULT_LOW_ADDR    0x1c
+#define VMCI_RESULT_HIGH_ADDR   0x20
+#define VMCI_DATA_OUT_LOW_ADDR  0x24
+#define VMCI_DATA_OUT_HIGH_ADDR 0x28
+#define VMCI_DATA_IN_LOW_ADDR   0x2c
+#define VMCI_DATA_IN_HIGH_ADDR  0x30
+#define VMCI_GUEST_PAGE_SHIFT   0x34
 
 /* Max number of devices. */
 #define VMCI_MAX_DEVICES 1
@@ -39,17 +44,27 @@
 #define VMCI_CAPS_DATAGRAM      BIT(2)
 #define VMCI_CAPS_NOTIFICATIONS BIT(3)
 #define VMCI_CAPS_PPN64         BIT(4)
+#define VMCI_CAPS_DMA_DATAGRAM  BIT(5)
 
 /* Interrupt Cause register bits. */
 #define VMCI_ICR_DATAGRAM      BIT(0)
 #define VMCI_ICR_NOTIFICATION  BIT(1)
+#define VMCI_ICR_DMA_DATAGRAM  BIT(2)
 
 /* Interrupt Mask register bits. */
 #define VMCI_IMR_DATAGRAM      BIT(0)
 #define VMCI_IMR_NOTIFICATION  BIT(1)
+#define VMCI_IMR_DMA_DATAGRAM  BIT(2)
 
-/* Maximum MSI/MSI-X interrupt vectors in the device. */
-#define VMCI_MAX_INTRS 2
+/*
+ * Maximum MSI/MSI-X interrupt vectors in the device.
+ * If VMCI_CAPS_DMA_DATAGRAM is supported by the device,
+ * VMCI_MAX_INTRS_DMA_DATAGRAM vectors are available,
+ * otherwise only VMCI_MAX_INTRS_NOTIFICATION.
+ */
+#define VMCI_MAX_INTRS_NOTIFICATION 2
+#define VMCI_MAX_INTRS_DMA_DATAGRAM 3
+#define VMCI_MAX_INTRS              VMCI_MAX_INTRS_DMA_DATAGRAM
 
 /*
  * Supported interrupt vectors.  There is one for each ICR value above,
@@ -58,6 +73,7 @@
 enum {
 	VMCI_INTR_DATAGRAM = 0,
 	VMCI_INTR_NOTIFICATION = 1,
+	VMCI_INTR_DMA_DATAGRAM = 2,
 };
 
 /*
@@ -83,6 +99,52 @@
 #define VMCI_MAX_PINNED_QP_MEMORY ((size_t)(32 * 1024))
 
 /*
+ * The version of the VMCI device that supports MMIO access to registers
+ * requests 256KB for BAR1 whereas the version of VMCI that supports
+ * MSI/MSI-X only requests 8KB. The layout of the larger 256KB region is:
+ * - the first 128KB are used for MSI/MSI-X.
+ * - the following 64KB are used for MMIO register access.
+ * - the remaining 64KB are unused.
+ */
+#define VMCI_WITH_MMIO_ACCESS_BAR_SIZE ((size_t)(256 * 1024))
+#define VMCI_MMIO_ACCESS_OFFSET        ((size_t)(128 * 1024))
+#define VMCI_MMIO_ACCESS_SIZE          ((size_t)(64 * 1024))
+
+/*
+ * For VMCI devices supporting the VMCI_CAPS_DMA_DATAGRAM capability, the
+ * sending and receiving of datagrams can be performed using DMA to/from
+ * a driver allocated buffer.
+ * Sending and receiving will be handled as follows:
+ * - when sending datagrams, the driver initializes the buffer where the
+ *   data part will refer to the outgoing VMCI datagram, sets the busy flag
+ *   to 1 and writes the address of the buffer to VMCI_DATA_OUT_HIGH_ADDR
+ *   and VMCI_DATA_OUT_LOW_ADDR. Writing to VMCI_DATA_OUT_LOW_ADDR triggers
+ *   the device processing of the buffer. When the device has processed the
+ *   buffer, it will write the result value to the buffer and then clear the
+ *   busy flag.
+ * - when receiving datagrams, the driver initializes the buffer where the
+ *   data part will describe the receive buffer, clears the busy flag and
+ *   writes the address of the buffer to VMCI_DATA_IN_HIGH_ADDR and
+ *   VMCI_DATA_IN_LOW_ADDR. Writing to VMCI_DATA_IN_LOW_ADDR triggers the
+ *   device processing of the buffer. The device will copy as many available
+ *   datagrams into the buffer as possible, and then sets the busy flag.
+ *   When the busy flag is set, the driver will process the datagrams in the
+ *   buffer.
+ */
+struct vmci_data_in_out_header {
+	uint32_t busy;
+	uint32_t opcode;
+	uint32_t size;
+	uint32_t rsvd;
+	uint64_t result;
+};
+
+struct vmci_sg_elem {
+	uint64_t addr;
+	uint64_t size;
+};
+
+/*
  * We have a fixed set of resource IDs available in the VMX.
  * This allows us to have a very simple implementation since we statically
  * know how many will create datagram handles. If a new caller arrives and
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vsc.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vsc.h
@@ -0,0 +1,83 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _LINUX_VSC_H_
+#define _LINUX_VSC_H_
+
+#include <linux/types.h>
+
+/**
+ * @brief VSC camera ownership definition
+ */
+enum vsc_camera_owner {
+	VSC_CAMERA_NONE = 0,
+	VSC_CAMERA_CVF,
+	VSC_CAMERA_IPU,
+};
+
+/**
+ * @brief VSC privacy status definition
+ */
+enum vsc_privacy_status {
+	VSC_PRIVACY_ON = 0,
+	VSC_PRIVACY_OFF,
+};
+
+/**
+ * @brief VSC MIPI configuration definition
+ */
+struct vsc_mipi_config {
+	uint32_t freq;
+	uint32_t lane_num;
+};
+
+/**
+ * @brief VSC camera status definition
+ */
+struct vsc_camera_status {
+	enum vsc_camera_owner owner;
+	enum vsc_privacy_status status;
+	uint32_t exposure_level;
+};
+
+/**
+ * @brief VSC privacy callback type definition
+ *
+ * @param context Privacy callback handle
+ * @param status Current privacy status
+ */
+typedef void (*vsc_privacy_callback_t)(void *handle,
+				       enum vsc_privacy_status status);
+
+/**
+ * @brief Acquire camera sensor ownership to IPU
+ *
+ * @param config[IN] The pointer of MIPI configuration going to set
+ * @param callback[IN] The pointer of privacy callback function
+ * @param handle[IN] Privacy callback function runtime handle from IPU driver
+ * @param status[OUT] The pointer of camera status after the acquire
+ *
+ * @retval 0 If success
+ * @retval -EIO IO error
+ * @retval -EINVAL Invalid argument
+ * @retval -EAGAIN VSC device not ready
+ * @retval negative values for other errors
+ */
+int vsc_acquire_camera_sensor(struct vsc_mipi_config *config,
+			      vsc_privacy_callback_t callback,
+			      void *handle,
+			      struct vsc_camera_status *status);
+
+/**
+ * @brief Release camera sensor ownership
+ *
+ * @param status[OUT] Camera status after the release
+ *
+ * @retval 0 If success
+ * @retval -EIO IO error
+ * @retval -EINVAL Invalid argument
+ * @retval -EAGAIN VSC device not ready
+ * @retval negative values for other errors
+ */
+int vsc_release_camera_sensor(struct vsc_camera_status *status);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/vt_buffer.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/vt_buffer.h
@@ -16,7 +16,7 @@
 
 #include <linux/string.h>
 
-#if defined(CONFIG_VGA_CONSOLE) || defined(CONFIG_MDA_CONSOLE)
+#if IS_ENABLED(CONFIG_VGA_CONSOLE) || IS_ENABLED(CONFIG_MDA_CONSOLE)
 #include <asm/vga.h>
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/wait.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/wait.h
@@ -217,12 +217,14 @@
 void __wake_up_locked_sync_key(struct wait_queue_head *wq_head, unsigned int mode, void *key);
 void __wake_up_locked(struct wait_queue_head *wq_head, unsigned int mode, int nr);
 void __wake_up_sync(struct wait_queue_head *wq_head, unsigned int mode);
+void __wake_up_pollfree(struct wait_queue_head *wq_head);
 
 #define wake_up(x)			__wake_up(x, TASK_NORMAL, 1, NULL)
 #define wake_up_nr(x, nr)		__wake_up(x, TASK_NORMAL, nr, NULL)
 #define wake_up_all(x)			__wake_up(x, TASK_NORMAL, 0, NULL)
 #define wake_up_locked(x)		__wake_up_locked((x), TASK_NORMAL, 1)
 #define wake_up_all_locked(x)		__wake_up_locked((x), TASK_NORMAL, 0)
+#define wake_up_sync(x)			__wake_up_sync(x, TASK_NORMAL)
 
 #define wake_up_interruptible(x)	__wake_up(x, TASK_INTERRUPTIBLE, 1, NULL)
 #define wake_up_interruptible_nr(x, nr)	__wake_up(x, TASK_INTERRUPTIBLE, nr, NULL)
@@ -245,6 +247,31 @@
 #define wake_up_interruptible_sync_poll_locked(x, m)				\
 	__wake_up_locked_sync_key((x), TASK_INTERRUPTIBLE, poll_to_key(m))
 
+/**
+ * wake_up_pollfree - signal that a polled waitqueue is going away
+ * @wq_head: the wait queue head
+ *
+ * In the very rare cases where a ->poll() implementation uses a waitqueue whose
+ * lifetime is tied to a task rather than to the 'struct file' being polled,
+ * this function must be called before the waitqueue is freed so that
+ * non-blocking polls (e.g. epoll) are notified that the queue is going away.
+ *
+ * The caller must also RCU-delay the freeing of the wait_queue_head, e.g. via
+ * an explicit synchronize_rcu() or call_rcu(), or via SLAB_TYPESAFE_BY_RCU.
+ */
+static inline void wake_up_pollfree(struct wait_queue_head *wq_head)
+{
+	/*
+	 * For performance reasons, we don't always take the queue lock here.
+	 * Therefore, we might race with someone removing the last entry from
+	 * the queue, and proceed while they still hold the queue lock.
+	 * However, rcu_read_lock() is required to be held in such cases, so we
+	 * can safely proceed with an RCU-delayed free.
+	 */
+	if (waitqueue_active(wq_head))
+		__wake_up_pollfree(wq_head);
+}
+
 #define ___wait_cond_timeout(condition)						\
 ({										\
 	bool __cond = (condition);						\
@@ -518,10 +545,11 @@
 										\
 	hrtimer_init_sleeper_on_stack(&__t, CLOCK_MONOTONIC,			\
 				      HRTIMER_MODE_REL);			\
-	if ((timeout) != KTIME_MAX)						\
-		hrtimer_start_range_ns(&__t.timer, timeout,			\
-				       current->timer_slack_ns,			\
-				       HRTIMER_MODE_REL);			\
+	if ((timeout) != KTIME_MAX) {						\
+		hrtimer_set_expires_range_ns(&__t.timer, timeout,		\
+					current->timer_slack_ns);		\
+		hrtimer_sleeper_start_expires(&__t, HRTIMER_MODE_REL);		\
+	}									\
 										\
 	__ret = ___wait_event(wq_head, condition, state, 0, 0,			\
 		if (!__t.task) {						\
@@ -1160,6 +1188,7 @@
 		(wait)->flags = 0;						\
 	} while (0)
 
-bool try_invoke_on_locked_down_task(struct task_struct *p, bool (*func)(struct task_struct *t, void *arg), void *arg);
+typedef int (*task_call_f)(struct task_struct *p, void *arg);
+extern int task_call_func(struct task_struct *p, task_call_f func, void *arg);
 
 #endif /* _LINUX_WAIT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/watch_queue.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/watch_queue.h
@@ -28,7 +28,8 @@
 struct watch_filter {
 	union {
 		struct rcu_head	rcu;
-		unsigned long	type_filter[2];	/* Bitmask of accepted types */
+		/* Bitmask of accepted types */
+		DECLARE_BITMAP(type_filter, WATCH_TYPE__NR);
 	};
 	u32			nr_filters;	/* Number of filters */
 	struct watch_type_filter filters[];
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/wireless.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/wireless.h
@@ -26,7 +26,15 @@
 struct __compat_iw_event {
 	__u16		len;			/* Real length of this stuff */
 	__u16		cmd;			/* Wireless IOCTL */
-	compat_caddr_t	pointer;
+
+	union {
+		compat_caddr_t	pointer;
+
+		/* we need ptr_bytes to make memcpy() run-time destination
+		 * buffer bounds checking happy, nothing special
+		 */
+		DECLARE_FLEX_ARRAY(__u8, ptr_bytes);
+	};
 };
 #define IW_EV_COMPAT_LCP_LEN offsetof(struct __compat_iw_event, pointer)
 #define IW_EV_COMPAT_POINT_OFF offsetof(struct compat_iw_point, length)
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/workqueue.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/workqueue.h
@@ -68,7 +68,6 @@
 	WORK_OFFQ_FLAG_BASE	= WORK_STRUCT_COLOR_SHIFT,
 
 	__WORK_OFFQ_CANCELING	= WORK_OFFQ_FLAG_BASE,
-	WORK_OFFQ_CANCELING	= (1 << __WORK_OFFQ_CANCELING),
 
 	/*
 	 * When a work item is off queue, its high bits point to the last
@@ -79,12 +78,6 @@
 	WORK_OFFQ_POOL_SHIFT	= WORK_OFFQ_FLAG_BASE + WORK_OFFQ_FLAG_BITS,
 	WORK_OFFQ_LEFT		= BITS_PER_LONG - WORK_OFFQ_POOL_SHIFT,
 	WORK_OFFQ_POOL_BITS	= WORK_OFFQ_LEFT <= 31 ? WORK_OFFQ_LEFT : 31,
-	WORK_OFFQ_POOL_NONE	= (1LU << WORK_OFFQ_POOL_BITS) - 1,
-
-	/* convenience constants */
-	WORK_STRUCT_FLAG_MASK	= (1UL << WORK_STRUCT_FLAG_BITS) - 1,
-	WORK_STRUCT_WQ_DATA_MASK = ~WORK_STRUCT_FLAG_MASK,
-	WORK_STRUCT_NO_POOL	= (unsigned long)WORK_OFFQ_POOL_NONE << WORK_OFFQ_POOL_SHIFT,
 
 	/* bit mask for work_busy() return values */
 	WORK_BUSY_PENDING	= 1 << 0,
@@ -94,6 +87,14 @@
 	WORKER_DESC_LEN		= 24,
 };
 
+/* Convenience constants - of type 'unsigned long', not 'enum'! */
+#define WORK_OFFQ_CANCELING	(1ul << __WORK_OFFQ_CANCELING)
+#define WORK_OFFQ_POOL_NONE	((1ul << WORK_OFFQ_POOL_BITS) - 1)
+#define WORK_STRUCT_NO_POOL	(WORK_OFFQ_POOL_NONE << WORK_OFFQ_POOL_SHIFT)
+
+#define WORK_STRUCT_FLAG_MASK    ((1ul << WORK_STRUCT_FLAG_BITS) - 1)
+#define WORK_STRUCT_WQ_DATA_MASK (~WORK_STRUCT_FLAG_MASK)
+
 struct work_struct {
 	atomic_long_t data;
 	struct list_head entry;
@@ -221,18 +222,16 @@
  * to generate better code.
  */
 #ifdef CONFIG_LOCKDEP
-#define __INIT_WORK(_work, _func, _onstack)				\
+#define __INIT_WORK_KEY(_work, _func, _onstack, _key)			\
 	do {								\
-		static struct lock_class_key __key;			\
-									\
 		__init_work((_work), _onstack);				\
 		(_work)->data = (atomic_long_t) WORK_DATA_INIT();	\
-		lockdep_init_map(&(_work)->lockdep_map, "(work_completion)"#_work, &__key, 0); \
+		lockdep_init_map(&(_work)->lockdep_map, "(work_completion)"#_work, (_key), 0); \
 		INIT_LIST_HEAD(&(_work)->entry);			\
 		(_work)->func = (_func);				\
 	} while (0)
 #else
-#define __INIT_WORK(_work, _func, _onstack)				\
+#define __INIT_WORK_KEY(_work, _func, _onstack, _key)			\
 	do {								\
 		__init_work((_work), _onstack);				\
 		(_work)->data = (atomic_long_t) WORK_DATA_INIT();	\
@@ -241,12 +240,22 @@
 	} while (0)
 #endif
 
+#define __INIT_WORK(_work, _func, _onstack)				\
+	do {								\
+		static __maybe_unused struct lock_class_key __key;	\
+									\
+		__INIT_WORK_KEY(_work, _func, _onstack, &__key);	\
+	} while (0)
+
 #define INIT_WORK(_work, _func)						\
 	__INIT_WORK((_work), (_func), 0)
 
 #define INIT_WORK_ONSTACK(_work, _func)					\
 	__INIT_WORK((_work), (_func), 1)
 
+#define INIT_WORK_ONSTACK_KEY(_work, _func, _key)			\
+	__INIT_WORK_KEY((_work), (_func), 1, _key)
+
 #define __INIT_DELAYED_WORK(_work, _func, _tflags)			\
 	do {								\
 		INIT_WORK(&(_work)->work, (_func));			\
@@ -453,6 +462,7 @@
 int execute_in_process_context(work_func_t fn, struct execute_work *);
 
 extern bool flush_work(struct work_struct *work);
+extern bool cancel_work(struct work_struct *work);
 extern bool cancel_work_sync(struct work_struct *work);
 
 extern bool flush_delayed_work(struct delayed_work *dwork);
@@ -469,7 +479,8 @@
 extern unsigned int work_busy(struct work_struct *work);
 extern __printf(1, 2) void set_worker_desc(const char *fmt, ...);
 extern void print_worker_info(const char *log_lvl, struct task_struct *task);
-extern void show_workqueue_state(void);
+extern void show_all_workqueues(void);
+extern void show_one_workqueue(struct workqueue_struct *wq);
 extern void wq_worker_comm(char *buf, size_t size, struct task_struct *task);
 
 /**
@@ -630,8 +641,32 @@
 	return fn(arg);
 }
 #else
-long work_on_cpu(int cpu, long (*fn)(void *), void *arg);
-long work_on_cpu_safe(int cpu, long (*fn)(void *), void *arg);
+long work_on_cpu_key(int cpu, long (*fn)(void *),
+		     void *arg, struct lock_class_key *key);
+/*
+ * A new key is defined for each caller to make sure the work
+ * associated with the function doesn't share its locking class.
+ */
+#define work_on_cpu(_cpu, _fn, _arg)			\
+({							\
+	static struct lock_class_key __key;		\
+							\
+	work_on_cpu_key(_cpu, _fn, _arg, &__key);	\
+})
+
+long work_on_cpu_safe_key(int cpu, long (*fn)(void *),
+			  void *arg, struct lock_class_key *key);
+
+/*
+ * A new key is defined for each caller to make sure the work
+ * associated with the function doesn't share its locking class.
+ */
+#define work_on_cpu_safe(_cpu, _fn, _arg)		\
+({							\
+	static struct lock_class_key __key;		\
+							\
+	work_on_cpu_safe_key(_cpu, _fn, _arg, &__key);	\
+})
 #endif /* CONFIG_SMP */
 
 #ifdef CONFIG_FREEZER
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/xattr.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/xattr.h
@@ -63,6 +63,7 @@
 int vfs_setxattr(struct user_namespace *, struct dentry *, const char *,
 		 const void *, size_t, int);
 int __vfs_removexattr(struct user_namespace *, struct dentry *, const char *);
+int __vfs_removexattr_noperm(struct user_namespace *, struct dentry *, const char *);
 int __vfs_removexattr_locked(struct user_namespace *, struct dentry *,
 			     const char *, struct inode **);
 int vfs_removexattr(struct user_namespace *, struct dentry *, const char *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/xilinx_phy.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/xilinx_phy.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx PHY specific header
+ *
+ * (C) Copyright 2015-2021 Xilinx, Inc. All rights reserved.
+ *
+ */
+
+#ifndef _XILINX_PHY_H
+#define _XILINX_PHY_H
+
+/* Mask used for ID comparisons */
+#define XILINX_PHY_ID_MASK		0xfffffff0
+
+/* Known PHY IDs */
+#define XILINX_PHY_ID			0x01740c00
+
+/* struct phy_device dev_flags definitions */
+#define XAE_PHY_TYPE_MII		0
+#define XAE_PHY_TYPE_GMII		1
+#define XAE_PHY_TYPE_RGMII_1_3		2
+#define XAE_PHY_TYPE_RGMII_2_0		3
+#define XAE_PHY_TYPE_SGMII		4
+#define XAE_PHY_TYPE_1000BASE_X		5
+#define XAE_PHY_TYPE_2500		6
+#define XXE_PHY_TYPE_USXGMII		7
+
+#endif /* _XILINX_PHY_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/linux/xlnx-ai-engine.h
+++ linux-xilinx-zynqmp-5.15.0/include/linux/xlnx-ai-engine.h
@@ -0,0 +1,182 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * xlnx-ai-engine.h - Xilinx AI engine external interface
+ *
+ * Copyright (c) 2020, Xilinx Inc.
+ */
+
+#ifndef _XLNX_AI_ENGINE_H_
+#define _XLNX_AI_ENGINE_H_
+
+#if !IS_ENABLED(CONFIG_XILINX_AIE)
+#include <linux/errno.h>
+#endif
+#include <uapi/linux/xlnx-ai-engine.h>
+
+/*
+ * Macro to classify errors into categories to provide higher-level error
+ * event abstraction.
+ */
+#define AIE_ERROR_CATEGORY_SATURATION		0U
+#define AIE_ERROR_CATEGORY_FP			1U
+#define AIE_ERROR_CATEGORY_STREAM		2U
+#define AIE_ERROR_CATEGORY_ACCESS		3U
+#define AIE_ERROR_CATEGORY_BUS			4U
+#define AIE_ERROR_CATEGORY_INSTRUCTION		5U
+#define AIE_ERROR_CATEGORY_ECC			6U
+#define AIE_ERROR_CATEGORY_LOCK			7U
+#define AIE_ERROR_CATEGORY_DMA			8U
+#define AIE_ERROR_CATEGORY_MEM_PARITY		9U
+
+/* AIE error category bit mask */
+#define AIE_ERROR_CATMASK(c)			BIT(AIE_ERROR_CATEGORY_##c)
+#define AIE_ERROR_CATEGORY_MASK_SATURATION	AIE_ERROR_CATMASK(SATURATION)
+#define AIE_ERROR_CATEGORY_MASK_FP		AIE_ERROR_CATMASK(FP)
+#define AIE_ERROR_CATEGORY_MASK_STREAM		AIE_ERROR_CATMASK(STREAM)
+#define AIE_ERROR_CATEGORY_MASK_ACCESS		AIE_ERROR_CATMASK(ACCESS)
+#define AIE_ERROR_CATEGORY_MASK_BUS		AIE_ERROR_CATMASK(BUS)
+#define AIE_ERROR_CATEGORY_MASK_INSTRUCTION	AIE_ERROR_CATMASK(INSTRUCTION)
+#define AIE_ERROR_CATEGORY_MASK_ECC		AIE_ERROR_CATMASK(ECC)
+#define AIE_ERROR_CATEGORY_MASK_LOCK		AIE_ERROR_CATMASK(LOCK)
+#define AIE_ERROR_CATEGORY_MASK_DMA		AIE_ERROR_CATMASK(DMA)
+#define AIE_ERROR_CATEGORY_MASK_MEM_PARITY	AIE_ERROR_CATMASK(MEM_PARITY)
+
+struct device;
+
+/**
+ * struct aie_error - AI engine error
+ * @loc: AI engine tile location of which the error is from
+ * @module: AI engine module type of which the error is from
+ * @error_id: AI engine hardware event ID
+ * @category: AI engine error category of the error
+ */
+struct aie_error {
+	struct aie_location loc;
+	enum aie_module_type module;
+	u32 error_id;
+	u32 category;
+};
+
+struct aie_errors {
+	struct device *dev;
+	struct aie_error *errors;
+	u32 num_err;
+};
+
+#if IS_ENABLED(CONFIG_XILINX_AIE)
+bool aie_partition_is_available(struct aie_partition_req *req);
+struct device *aie_partition_request(struct aie_partition_req *req);
+int aie_partition_get_fd(struct device *dev);
+void aie_partition_release(struct device *dev);
+int aie_partition_reset(struct device *dev);
+int aie_partition_post_reinit(struct device *dev);
+
+int aie_register_error_notification(struct device *dev,
+				    void (*cb)(void *priv), void *priv);
+int aie_unregister_error_notification(struct device *dev);
+struct aie_errors *aie_get_errors(struct device *dev);
+u32 aie_get_error_categories(struct aie_errors *aie_errs);
+const char *aie_get_error_string(struct aie_errors *aie_errs,
+				 struct aie_error *aie_err);
+int aie_flush_errors(struct device *dev);
+void aie_free_errors(struct aie_errors *aie_errs);
+
+int aie_partition_set_freq_req(struct device *dev, u64 freq);
+int aie_partition_get_freq(struct device *dev, u64 *freq);
+int aie_partition_get_freq_req(struct device *dev, u64 *freq);
+
+/**
+ * aie_get_error_category() - Get the category of an AIE error
+ * @err: AI engine hardware error
+ * @return: category of the error
+ */
+static inline u32 aie_get_error_category(struct aie_error *err)
+{
+	return err->category;
+}
+
+#else
+static inline bool aie_partition_is_available(struct aie_partition_req *req)
+{
+	return false;
+}
+
+static inline struct device *
+aie_partition_request(struct aie_partition_req *req)
+{
+	return NULL;
+}
+
+static inline int aie_partition_get_fd(struct device *dev)
+{
+	return -EINVAL;
+}
+
+static inline void aie_partition_release(struct device *dev) {}
+
+static inline int aie_partition_reset(struct device *dev)
+{
+	return -EINVAL;
+}
+
+static inline int aie_partition_post_reinit(struct device *dev)
+{
+	return -EINVAL;
+}
+
+static inline int
+aie_register_error_notification(struct device *dev, void (*cb)(void *priv),
+				void *priv)
+{
+	return -EINVAL;
+}
+
+static inline int aie_unregister_error_notification(struct device *dev)
+{
+	return -EINVAL;
+}
+
+static inline struct aie_errors *aie_get_errors(struct device *dev)
+{
+	return NULL;
+}
+
+static inline u32 aie_get_error_categories(struct aie_errors *aie_errs)
+{
+	return 0;
+}
+
+static inline const char *aie_get_error_string(struct aie_errors *aie_errs,
+					       struct aie_error *aie_err)
+{
+	return NULL;
+}
+
+static inline int aie_flush_errors(struct device *dev)
+{
+	return -EINVAL;
+}
+
+static inline void aie_free_errors(struct aie_errors *aie_errs) {}
+
+static inline u32 aie_get_error_category(struct aie_error *err)
+{
+	return 0;
+}
+
+static inline int aie_partition_set_freq_req(struct device *dev, u64 freq)
+{
+	return -EINVAL;
+}
+
+static inline int aie_partition_get_freq(struct device *dev, u64 *freq)
+{
+	return -EINVAL;
+}
+
+static inline int aie_partition_get_freq_req(struct device *dev, u64 *freq)
+{
+	return -EINVAL;
+}
+#endif /* CONFIG_XILINX_AIE */
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/cec.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/cec.h
@@ -26,13 +26,17 @@
  * @dev:	cec device
  * @cdev:	cec character device
  * @minor:	device node minor number
+ * @lock:	lock to serialize open/release and registration
  * @registered:	the device was correctly registered
  * @unregistered: the device was unregistered
+ * @lock_fhs:	lock to control access to @fhs
  * @fhs:	the list of open filehandles (cec_fh)
- * @lock:	lock to control access to this structure
  *
  * This structure represents a cec-related device node.
  *
+ * To add or remove filehandles from @fhs the @lock must be taken first,
+ * followed by @lock_fhs. It is safe to access @fhs if either lock is held.
+ *
  * The @parent is a physical device. It must be set by core or device drivers
  * before registering the node.
  */
@@ -43,10 +47,13 @@
 
 	/* device info */
 	int minor;
+	/* serialize open/release and registration */
+	struct mutex lock;
 	bool registered;
 	bool unregistered;
+	/* protect access to fhs */
+	struct mutex lock_fhs;
 	struct list_head fhs;
-	struct mutex lock;
 };
 
 struct cec_adapter;
@@ -113,14 +120,16 @@
 	int (*adap_log_addr)(struct cec_adapter *adap, u8 logical_addr);
 	int (*adap_transmit)(struct cec_adapter *adap, u8 attempts,
 			     u32 signal_free_time, struct cec_msg *msg);
+	void (*adap_nb_transmit_canceled)(struct cec_adapter *adap,
+					  const struct cec_msg *msg);
 	void (*adap_status)(struct cec_adapter *adap, struct seq_file *file);
 	void (*adap_free)(struct cec_adapter *adap);
 
-	/* Error injection callbacks */
+	/* Error injection callbacks, called without adap->lock held */
 	int (*error_inj_show)(struct cec_adapter *adap, struct seq_file *sf);
 	bool (*error_inj_parse_line)(struct cec_adapter *adap, char *line);
 
-	/* High-level CEC message callback */
+	/* High-level CEC message callback, called without adap->lock held */
 	int (*received)(struct cec_adapter *adap, struct cec_msg *msg);
 };
 
@@ -156,6 +165,11 @@
  * @wait_queue:		queue of transmits waiting for a reply
  * @transmitting:	CEC messages currently being transmitted
  * @transmit_in_progress: true if a transmit is in progress
+ * @transmit_in_progress_aborted: true if a transmit is in progress is to be
+ *			aborted. This happens if the logical address is
+ *			invalidated while the transmit is ongoing. In that
+ *			case the transmit will finish, but will not retransmit
+ *			and be marked as ABORTED.
  * @kthread_config:	kthread used to configure a CEC adapter
  * @config_completion:	used to signal completion of the config kthread
  * @kthread:		main CEC processing thread
@@ -168,6 +182,7 @@
  * @needs_hpd:		if true, then the HDMI HotPlug Detect pin must be high
  *	in order to transmit or receive CEC messages. This is usually a HW
  *	limitation.
+ * @is_enabled:		the CEC adapter is enabled
  * @is_configuring:	the CEC adapter is configuring (i.e. claiming LAs)
  * @is_configured:	the CEC adapter is configured (i.e. has claimed LAs)
  * @cec_pin_is_high:	if true then the CEC pin is high. Only used with the
@@ -210,6 +225,7 @@
 	struct list_head wait_queue;
 	struct cec_data *transmitting;
 	bool transmit_in_progress;
+	bool transmit_in_progress_aborted;
 
 	struct task_struct *kthread_config;
 	struct completion config_completion;
@@ -224,6 +240,8 @@
 
 	u16 phys_addr;
 	bool needs_hpd;
+	bool is_enabled;
+	bool is_claiming_log_addrs;
 	bool is_configuring;
 	bool is_configured;
 	bool cec_pin_is_high;
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/dvb_net.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/dvb_net.h
@@ -41,6 +41,9 @@
  * @exit:		flag to indicate when the device is being removed.
  * @demux:		pointer to &struct dmx_demux.
  * @ioctl_mutex:	protect access to this struct.
+ * @remove_mutex:	mutex that avoids a race condition between a callback
+ *			called when the hardware is disconnected and the
+ *			file_operations of dvb_net.
  *
  * Currently, the core supports up to %DVB_NET_DEVICES_MAX (10) network
  * devices.
@@ -53,6 +56,7 @@
 	unsigned int exit:1;
 	struct dmx_demux *demux;
 	struct mutex ioctl_mutex;
+	struct mutex remove_mutex;
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/dvbdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/dvbdev.h
@@ -126,6 +126,7 @@
  * struct dvb_device - represents a DVB device node
  *
  * @list_head:	List head with all DVB devices
+ * @ref:	reference counter
  * @fops:	pointer to struct file_operations
  * @adapter:	pointer to the adapter that holds this device node
  * @type:	type of the device, as defined by &enum dvb_device_type.
@@ -156,6 +157,7 @@
  */
 struct dvb_device {
 	struct list_head list_head;
+	struct kref ref;
 	const struct file_operations *fops;
 	struct dvb_adapter *adapter;
 	enum dvb_device_type type;
@@ -188,6 +190,35 @@
 };
 
 /**
+ * struct dvbdevfops_node - fops nodes registered in dvbdevfops_list
+ *
+ * @fops:		Dynamically allocated fops for ->owner registration
+ * @type:		type of dvb_device
+ * @template:		dvb_device used for registration
+ * @list_head:		list_head for dvbdevfops_list
+ */
+struct dvbdevfops_node {
+	struct file_operations *fops;
+	enum dvb_device_type type;
+	const struct dvb_device *template;
+	struct list_head list_head;
+};
+
+/**
+ * dvb_device_get - Increase dvb_device reference
+ *
+ * @dvbdev:	pointer to struct dvb_device
+ */
+struct dvb_device *dvb_device_get(struct dvb_device *dvbdev);
+
+/**
+ * dvb_device_put - Decrease dvb_device reference
+ *
+ * @dvbdev:	pointer to struct dvb_device
+ */
+void dvb_device_put(struct dvb_device *dvbdev);
+
+/**
  * dvb_register_adapter - Registers a new DVB adapter
  *
  * @adap:	pointer to struct dvb_adapter
@@ -231,29 +262,17 @@
 /**
  * dvb_remove_device - Remove a registered DVB device
  *
- * This does not free memory.  To do that, call dvb_free_device().
+ * This does not free memory. dvb_free_device() will do that when
+ * reference counter is empty
  *
  * @dvbdev:	pointer to struct dvb_device
  */
 void dvb_remove_device(struct dvb_device *dvbdev);
 
-/**
- * dvb_free_device - Free memory occupied by a DVB device.
- *
- * Call dvb_unregister_device() before calling this function.
- *
- * @dvbdev:	pointer to struct dvb_device
- */
-void dvb_free_device(struct dvb_device *dvbdev);
 
 /**
  * dvb_unregister_device - Unregisters a DVB device
  *
- * This is a combination of dvb_remove_device() and dvb_free_device().
- * Using this function is usually a mistake, and is often an indicator
- * for a use-after-free bug (when a userspace process keeps a file
- * handle to a detached device).
- *
  * @dvbdev:	pointer to struct dvb_device
  */
 void dvb_unregister_device(struct dvb_device *dvbdev);
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/hdr-ctrls.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/hdr-ctrls.h
@@ -0,0 +1,91 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * These are the HDR controls for use with the extended control API.
+ *
+ * It turns out that these structs are not stable yet and will undergo
+ * more changes. So keep them private until they are stable and ready to
+ * become part of the official public API.
+ */
+
+#ifndef _HDR_CTRLS_H_
+#define _HDR_CTRLS_H_
+
+#include <linux/types.h>
+
+#define V4L2_CTRL_CLASS_METADATA 0x00b00000
+
+#define V4L2_CID_METADATA_BASE (V4L2_CTRL_CLASS_METADATA | 0x900)
+#define V4L2_CID_METADATA_CLASS (V4L2_CTRL_CLASS_METADATA | 1)
+
+#define V4L2_CID_METADATA_HDR (V4L2_CID_METADATA_BASE + 1)
+
+enum v4l2_eotf {
+	/*
+	 * EOTF values as per CTA 861.G spec (HDMI/DP).
+	 * If v4l2 driver is being implemented for other connectivity devices,
+	 * a conversion function must be implemented.
+	 */
+	V4L2_EOTF_TRADITIONAL_GAMMA_SDR,
+	V4L2_EOTF_TRADITIONAL_GAMMA_HDR,
+	V4L2_EOTF_SMPTE_ST2084,
+	V4L2_EOTF_BT_2100_HLG,
+};
+
+enum v4l2_hdr_type {
+	/*
+	 * This is for the v4l2_metadata_hdr structure.
+	 * MSB differentiates static (0) or dynamic (1) metadata.
+	 * Other 15 bits represent specific HDR standards.
+	 */
+
+	/* static HDR */
+	V4L2_HDR_TYPE_HDR10     = 0x0000,
+
+	/* dynamic HDR */
+	V4L2_HDR_TYPE_HDR10P    = 1 << 15 | V4L2_HDR_TYPE_HDR10,
+};
+
+/**
+ * struct v4l2_hdr10_payload - HDR Metadata Payload which matches CTA 861.G spec
+ *
+ * @eotf:				Electro-Optical Transfer Function (EOTF)
+ * @metadata_type:			Static_Metadata_Descriptor_ID
+ * @display_primaries:			Color Primaries of the Data
+ * @white_point:			White Point of Colorspace Data
+ * @max_mdl:				Max Mastering Display Luminance
+ * @min_mdl:				Min Mastering Display Luminance
+ * @max_cll:				Max Content Light Level
+ * @max_fall:				Max Frame Average Light Level
+ */
+struct v4l2_hdr10_payload {
+	__u8 eotf;
+	__u8 metadata_type;
+	struct {
+		__u16 x;
+		__u16 y;
+	} display_primaries[3];
+	struct {
+		__u16 x;
+		__u16 y;
+	} white_point;
+	__u16 max_mdl;
+	__u16 min_mdl;
+	__u16 max_cll;
+	__u16 max_fall;
+};
+
+/**
+ * struct v4l2_metadata_hdr - Container for HDR metadata
+ *
+ * @metadata_type:	HDR type
+ * @size:		Size of payload/metadata
+ * @payload:		Actual metadata
+ */
+struct v4l2_metadata_hdr {
+	__u16 metadata_type;
+	__u16 size;
+	/* Currently the largest extended HDR infoframe is 4000 bytes */
+	__u8 payload[4000];
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/ipu-isys.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/ipu-isys.h
@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2014 - 2020 Intel Corporation */
+
+#ifndef MEDIA_IPU_H
+#define MEDIA_IPU_H
+
+#include <linux/i2c.h>
+#include <linux/clkdev.h>
+#include <media/v4l2-async.h>
+
+#define IPU_ISYS_MAX_CSI2_LANES		4
+
+struct ipu_isys_csi2_config {
+	unsigned int nlanes;
+	unsigned int port;
+};
+
+struct ipu_isys_subdev_i2c_info {
+	struct i2c_board_info board_info;
+	int i2c_adapter_id;
+	char i2c_adapter_bdf[32];
+};
+
+struct ipu_isys_subdev_info {
+	struct ipu_isys_csi2_config *csi2;
+	struct ipu_isys_subdev_i2c_info i2c;
+};
+
+struct ipu_isys_clk_mapping {
+	struct clk_lookup clkdev_data;
+	char *platform_clock_name;
+};
+
+struct ipu_isys_subdev_pdata {
+	struct ipu_isys_subdev_info **subdevs;
+	struct ipu_isys_clk_mapping *clk_map;
+};
+
+struct sensor_async_subdev {
+	struct v4l2_async_subdev asd;
+	struct ipu_isys_csi2_config csi2;
+};
+
+#endif /* MEDIA_IPU_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/media-entity.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/media-entity.h
@@ -205,6 +205,9 @@
  * @link_validate:	Return whether a link is valid from the entity point of
  *			view. The media_pipeline_start() function
  *			validates all links by calling this operation. Optional.
+ * @has_route:		Return whether a route exists inside the entity between
+ *			two given pads. Optional. If the operation isn't
+ *			implemented all pads will be considered as connected.
  *
  * .. note::
  *
@@ -218,6 +221,8 @@
 			  const struct media_pad *local,
 			  const struct media_pad *remote, u32 flags);
 	int (*link_validate)(struct media_link *link);
+	bool (*has_route)(struct media_entity *entity, unsigned int pad0,
+			  unsigned int pad1);
 };
 
 /**
@@ -901,6 +906,9 @@
  */
 void media_graph_walk_cleanup(struct media_graph *graph);
 
+bool media_entity_has_route(struct media_entity *entity, unsigned int sink,
+			    unsigned int source);
+
 /**
  * media_graph_walk_start - Start walking the media graph at a
  *	given entity
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/v4l2-common.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/v4l2-common.h
@@ -175,7 +175,8 @@
  *
  * @sd: pointer to &struct v4l2_subdev
  * @client: pointer to struct i2c_client
- * @devname: the name of the device; if NULL, the I²C device's name will be used
+ * @devname: the name of the device; if NULL, the I²C device drivers's name
+ *           will be used
  * @postfix: sub-device specific string to put right after the I²C device name;
  *	     may be NULL
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/v4l2-dv-timings.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/v4l2-dv-timings.h
@@ -146,15 +146,18 @@
  * @polarities: the horizontal and vertical polarities (same as struct
  *		v4l2_bt_timings polarities).
  * @interlaced: if this flag is true, it indicates interlaced format
+ * @cap: the v4l2_dv_timings_cap capabilities.
  * @fmt: the resulting timings.
  *
  * This function will attempt to detect if the given values correspond to a
  * valid CVT format. If so, then it will return true, and fmt will be filled
  * in with the found CVT timings.
  */
-bool v4l2_detect_cvt(unsigned frame_height, unsigned hfreq, unsigned vsync,
-		unsigned active_width, u32 polarities, bool interlaced,
-		struct v4l2_dv_timings *fmt);
+bool v4l2_detect_cvt(unsigned int frame_height, unsigned int hfreq,
+		     unsigned int vsync, unsigned int active_width,
+		     u32 polarities, bool interlaced,
+		     const struct v4l2_dv_timings_cap *cap,
+		     struct v4l2_dv_timings *fmt);
 
 /**
  * v4l2_detect_gtf - detect if the given timings follow the GTF standard
@@ -170,15 +173,18 @@
  *		image height, so it has to be passed explicitly. Usually
  *		the native screen aspect ratio is used for this. If it
  *		is not filled in correctly, then 16:9 will be assumed.
+ * @cap: the v4l2_dv_timings_cap capabilities.
  * @fmt: the resulting timings.
  *
  * This function will attempt to detect if the given values correspond to a
  * valid GTF format. If so, then it will return true, and fmt will be filled
  * in with the found GTF timings.
  */
-bool v4l2_detect_gtf(unsigned frame_height, unsigned hfreq, unsigned vsync,
-		u32 polarities, bool interlaced, struct v4l2_fract aspect,
-		struct v4l2_dv_timings *fmt);
+bool v4l2_detect_gtf(unsigned int frame_height, unsigned int hfreq,
+		     unsigned int vsync, u32 polarities, bool interlaced,
+		     struct v4l2_fract aspect,
+		     const struct v4l2_dv_timings_cap *cap,
+		     struct v4l2_dv_timings *fmt);
 
 /**
  * v4l2_calc_aspect_ratio - calculate the aspect ratio based on bytes
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/v4l2-mem2mem.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/v4l2-mem2mem.h
@@ -588,7 +588,14 @@
 static inline
 unsigned int v4l2_m2m_num_src_bufs_ready(struct v4l2_m2m_ctx *m2m_ctx)
 {
-	return m2m_ctx->out_q_ctx.num_rdy;
+	unsigned int num_buf_rdy;
+	unsigned long flags;
+
+	spin_lock_irqsave(&m2m_ctx->out_q_ctx.rdy_spinlock, flags);
+	num_buf_rdy = m2m_ctx->out_q_ctx.num_rdy;
+	spin_unlock_irqrestore(&m2m_ctx->out_q_ctx.rdy_spinlock, flags);
+
+	return num_buf_rdy;
 }
 
 /**
@@ -600,7 +607,14 @@
 static inline
 unsigned int v4l2_m2m_num_dst_bufs_ready(struct v4l2_m2m_ctx *m2m_ctx)
 {
-	return m2m_ctx->cap_q_ctx.num_rdy;
+	unsigned int num_buf_rdy;
+	unsigned long flags;
+
+	spin_lock_irqsave(&m2m_ctx->cap_q_ctx.rdy_spinlock, flags);
+	num_buf_rdy = m2m_ctx->cap_q_ctx.num_rdy;
+	spin_unlock_irqrestore(&m2m_ctx->cap_q_ctx.rdy_spinlock, flags);
+
+	return num_buf_rdy;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/v4l2-subdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/v4l2-subdev.h
@@ -770,6 +770,10 @@
 			       struct v4l2_mbus_config *config);
 	int (*set_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
 			       struct v4l2_mbus_config *config);
+	int (*get_routing)(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_routing *route);
+	int (*set_routing)(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_routing *route);
 };
 
 /**
@@ -995,6 +999,8 @@
 			   struct v4l2_subdev_state *state,
 			   unsigned int pad)
 {
+	if (WARN_ON(!state))
+		return NULL;
 	if (WARN_ON(pad >= sd->entity.num_pads))
 		pad = 0;
 	return &state->pads[pad].try_fmt;
@@ -1013,6 +1019,8 @@
 			 struct v4l2_subdev_state *state,
 			 unsigned int pad)
 {
+	if (WARN_ON(!state))
+		return NULL;
 	if (WARN_ON(pad >= sd->entity.num_pads))
 		pad = 0;
 	return &state->pads[pad].try_crop;
@@ -1031,6 +1039,8 @@
 			    struct v4l2_subdev_state *state,
 			    unsigned int pad)
 {
+	if (WARN_ON(!state))
+		return NULL;
 	if (WARN_ON(pad >= sd->entity.num_pads))
 		pad = 0;
 	return &state->pads[pad].try_compose;
--- linux-xilinx-zynqmp-5.15.0.orig/include/media/videobuf2-core.h
+++ linux-xilinx-zynqmp-5.15.0/include/media/videobuf2-core.h
@@ -46,6 +46,7 @@
 
 struct vb2_fileio_data;
 struct vb2_threadio_data;
+struct vb2_buffer;
 
 /**
  * struct vb2_mem_ops - memory handling/memory allocator operations.
@@ -53,10 +54,8 @@
  *		return ERR_PTR() on failure or a pointer to allocator private,
  *		per-buffer data on success; the returned private structure
  *		will then be passed as @buf_priv argument to other ops in this
- *		structure. Additional gfp_flags to use when allocating the
- *		are also passed to this operation. These flags are from the
- *		gfp_flags field of vb2_queue. The size argument to this function
- *		shall be *page aligned*.
+ *		structure. The size argument to this function shall be
+ *		*page aligned*.
  * @put:	inform the allocator that the buffer will no longer be used;
  *		usually will result in the allocator freeing the buffer (if
  *		no other users of this buffer are present); the @buf_priv
@@ -117,31 +116,33 @@
  *       map_dmabuf, unmap_dmabuf.
  */
 struct vb2_mem_ops {
-	void		*(*alloc)(struct device *dev, unsigned long attrs,
-				  unsigned long size,
-				  enum dma_data_direction dma_dir,
-				  gfp_t gfp_flags);
+	void		*(*alloc)(struct vb2_buffer *vb,
+				  struct device *dev,
+				  unsigned long size);
 	void		(*put)(void *buf_priv);
-	struct dma_buf *(*get_dmabuf)(void *buf_priv, unsigned long flags);
-
-	void		*(*get_userptr)(struct device *dev, unsigned long vaddr,
-					unsigned long size,
-					enum dma_data_direction dma_dir);
+	struct dma_buf *(*get_dmabuf)(struct vb2_buffer *vb,
+				      void *buf_priv,
+				      unsigned long flags);
+
+	void		*(*get_userptr)(struct vb2_buffer *vb,
+					struct device *dev,
+					unsigned long vaddr,
+					unsigned long size);
 	void		(*put_userptr)(void *buf_priv);
 
 	void		(*prepare)(void *buf_priv);
 	void		(*finish)(void *buf_priv);
 
-	void		*(*attach_dmabuf)(struct device *dev,
+	void		*(*attach_dmabuf)(struct vb2_buffer *vb,
+					  struct device *dev,
 					  struct dma_buf *dbuf,
-					  unsigned long size,
-					  enum dma_data_direction dma_dir);
+					  unsigned long size);
 	void		(*detach_dmabuf)(void *buf_priv);
 	int		(*map_dmabuf)(void *buf_priv);
 	void		(*unmap_dmabuf)(void *buf_priv);
 
-	void		*(*vaddr)(void *buf_priv);
-	void		*(*cookie)(void *buf_priv);
+	void		*(*vaddr)(struct vb2_buffer *vb, void *buf_priv);
+	void		*(*cookie)(struct vb2_buffer *vb, void *buf_priv);
 
 	unsigned int	(*num_users)(void *buf_priv);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/memory/renesas-rpc-if.h
+++ linux-xilinx-zynqmp-5.15.0/include/memory/renesas-rpc-if.h
@@ -59,12 +59,14 @@
 
 struct rpcif {
 	struct device *dev;
+	void __iomem *base;
 	void __iomem *dirmap;
 	struct regmap *regmap;
 	struct reset_control *rstc;
 	size_t size;
 	enum rpcif_data_dir dir;
 	u8 bus_size;
+	u8 xfer_size;
 	void *buffer;
 	u32 xferlen;
 	u32 smcr;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/9p/9p.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/9p/9p.h
@@ -32,13 +32,13 @@
  */
 
 enum p9_debug_flags {
-	P9_DEBUG_ERROR = 	(1<<0),
-	P9_DEBUG_9P = 		(1<<2),
+	P9_DEBUG_ERROR =	(1<<0),
+	P9_DEBUG_9P =		(1<<2),
 	P9_DEBUG_VFS =		(1<<3),
 	P9_DEBUG_CONV =		(1<<4),
 	P9_DEBUG_MUX =		(1<<5),
 	P9_DEBUG_TRANS =	(1<<6),
-	P9_DEBUG_SLABS =      	(1<<7),
+	P9_DEBUG_SLABS =	(1<<7),
 	P9_DEBUG_FCALL =	(1<<8),
 	P9_DEBUG_FID =		(1<<9),
 	P9_DEBUG_PKT =		(1<<10),
@@ -317,8 +317,8 @@
 };
 
 /* 9P Magic Numbers */
-#define P9_NOTAG	(u16)(~0)
-#define P9_NOFID	(u32)(~0)
+#define P9_NOTAG	((u16)(~0))
+#define P9_NOFID	((u32)(~0))
 #define P9_MAXWELEM	16
 
 /* Minimal header size: size[4] type[1] tag[2] */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/9p/client.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/9p/client.h
@@ -23,7 +23,7 @@
  * @p9_proto_2000L: 9P2000.L extension
  */
 
-enum p9_proto_versions{
+enum p9_proto_versions {
 	p9_proto_legacy,
 	p9_proto_2000u,
 	p9_proto_2000L,
@@ -78,7 +78,7 @@
 struct p9_req_t {
 	int status;
 	int t_err;
-	struct kref refcount;
+	refcount_t refcount;
 	wait_queue_head_t wq;
 	struct p9_fcall tc;
 	struct p9_fcall rc;
@@ -219,36 +219,40 @@
 							u64 request_mask);
 
 int p9_client_mknod_dotl(struct p9_fid *oldfid, const char *name, int mode,
-			dev_t rdev, kgid_t gid, struct p9_qid *);
+			dev_t rdev, kgid_t gid, struct p9_qid *qid);
 int p9_client_mkdir_dotl(struct p9_fid *fid, const char *name, int mode,
-				kgid_t gid, struct p9_qid *);
+				kgid_t gid, struct p9_qid *qid);
 int p9_client_lock_dotl(struct p9_fid *fid, struct p9_flock *flock, u8 *status);
 int p9_client_getlock_dotl(struct p9_fid *fid, struct p9_getlock *fl);
 void p9_fcall_fini(struct p9_fcall *fc);
-struct p9_req_t *p9_tag_lookup(struct p9_client *, u16);
+struct p9_req_t *p9_tag_lookup(struct p9_client *c, u16 tag);
 
 static inline void p9_req_get(struct p9_req_t *r)
 {
-	kref_get(&r->refcount);
+	refcount_inc(&r->refcount);
 }
 
 static inline int p9_req_try_get(struct p9_req_t *r)
 {
-	return kref_get_unless_zero(&r->refcount);
+	return refcount_inc_not_zero(&r->refcount);
 }
 
-int p9_req_put(struct p9_req_t *r);
+int p9_req_put(struct p9_client *c, struct p9_req_t *r);
 
 void p9_client_cb(struct p9_client *c, struct p9_req_t *req, int status);
 
-int p9_parse_header(struct p9_fcall *, int32_t *, int8_t *, int16_t *, int);
-int p9stat_read(struct p9_client *, char *, int, struct p9_wstat *);
-void p9stat_free(struct p9_wstat *);
+int p9_parse_header(struct p9_fcall *pdu, int32_t *size, int8_t *type,
+		    int16_t *tag, int rewind);
+int p9stat_read(struct p9_client *clnt, char *buf, int len,
+		struct p9_wstat *st);
+void p9stat_free(struct p9_wstat *stbuf);
 
 int p9_is_proto_dotu(struct p9_client *clnt);
 int p9_is_proto_dotl(struct p9_client *clnt);
-struct p9_fid *p9_client_xattrwalk(struct p9_fid *, const char *, u64 *);
-int p9_client_xattrcreate(struct p9_fid *, const char *, u64, int);
+struct p9_fid *p9_client_xattrwalk(struct p9_fid *file_fid,
+				   const char *attr_name, u64 *attr_size);
+int p9_client_xattrcreate(struct p9_fid *fid, const char *name,
+			  u64 attr_size, int flags);
 int p9_client_readlink(struct p9_fid *fid, char **target);
 
 int p9_client_init(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/9p/transport.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/9p/transport.h
@@ -40,14 +40,16 @@
 	int maxsize;		/* max message size of transport */
 	int def;		/* this transport should be default */
 	struct module *owner;
-	int (*create)(struct p9_client *, const char *, char *);
-	void (*close) (struct p9_client *);
-	int (*request) (struct p9_client *, struct p9_req_t *req);
-	int (*cancel) (struct p9_client *, struct p9_req_t *req);
-	int (*cancelled)(struct p9_client *, struct p9_req_t *req);
-	int (*zc_request)(struct p9_client *, struct p9_req_t *,
-			  struct iov_iter *, struct iov_iter *, int , int, int);
-	int (*show_options)(struct seq_file *, struct p9_client *);
+	int (*create)(struct p9_client *client,
+		      const char *devname, char *args);
+	void (*close)(struct p9_client *client);
+	int (*request)(struct p9_client *client, struct p9_req_t *req);
+	int (*cancel)(struct p9_client *client, struct p9_req_t *req);
+	int (*cancelled)(struct p9_client *client, struct p9_req_t *req);
+	int (*zc_request)(struct p9_client *client, struct p9_req_t *req,
+			  struct iov_iter *uidata, struct iov_iter *uodata,
+			  int inlen, int outlen, int in_hdr_len);
+	int (*show_options)(struct seq_file *m, struct p9_client *client);
 };
 
 void v9fs_register_trans(struct p9_trans_module *m);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/addrconf.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/addrconf.h
@@ -6,6 +6,8 @@
 #define RTR_SOLICITATION_INTERVAL	(4*HZ)
 #define RTR_SOLICITATION_MAX_INTERVAL	(3600*HZ)	/* 1 hour */
 
+#define MIN_VALID_LIFETIME		(2*3600)	/* 2 hours */
+
 #define TEMP_VALID_LIFETIME		(7*86400)
 #define TEMP_PREFERRED_LIFETIME		(86400)
 #define REGEN_MAX_RETRY			(3)
@@ -29,17 +31,22 @@
 	__u8			length;
 	__u8			prefix_len;
 
+	union __packed {
+		__u8		flags;
+		struct __packed {
 #if defined(__BIG_ENDIAN_BITFIELD)
-	__u8			onlink : 1,
+			__u8	onlink : 1,
 			 	autoconf : 1,
 				reserved : 6;
 #elif defined(__LITTLE_ENDIAN_BITFIELD)
-	__u8			reserved : 6,
+			__u8	reserved : 6,
 				autoconf : 1,
 				onlink : 1;
 #else
 #error "Please fix <asm/byteorder.h>"
 #endif
+		};
+	};
 	__be32			valid;
 	__be32			prefered;
 	__be32			reserved2;
@@ -47,6 +54,9 @@
 	struct in6_addr		prefix;
 };
 
+/* rfc4861 4.6.2: IPv6 PIO is 32 bytes in size */
+static_assert(sizeof(struct prefix_info) == 32);
+
 #include <linux/ipv6.h>
 #include <linux/netdevice.h>
 #include <net/if_inet6.h>
@@ -107,8 +117,6 @@
 int ipv6_dev_get_saddr(struct net *net, const struct net_device *dev,
 		       const struct in6_addr *daddr, unsigned int srcprefs,
 		       struct in6_addr *saddr);
-int __ipv6_get_lladdr(struct inet6_dev *idev, struct in6_addr *addr,
-		      u32 banned_flags);
 int ipv6_get_lladdr(struct net_device *dev, struct in6_addr *addr,
 		    u32 banned_flags);
 bool inet_rcv_saddr_equal(const struct sock *sk, const struct sock *sk2,
@@ -403,6 +411,9 @@
 {
 	const struct inet6_dev *idev = __in6_dev_get(dev);
 
+	if (unlikely(!idev))
+		return true;
+
 	return !!idev->cnf.ignore_routes_with_linkdown;
 }
 
@@ -424,6 +435,10 @@
 	refcount_inc(&ifp->refcnt);
 }
 
+static inline bool in6_ifa_hold_safe(struct inet6_ifaddr *ifp)
+{
+	return refcount_inc_not_zero(&ifp->refcnt);
+}
 
 /*
  *	compute link-local solicited-node multicast address
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/af_unix.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/af_unix.h
@@ -36,7 +36,7 @@
 	kgid_t			gid;
 	struct scm_fp_list	*fp;		/* Passed files		*/
 #ifdef CONFIG_SECURITY_NETWORK
-	u32			secid;		/* Security ID		*/
+	struct lsmblob		lsmblob;	/* Security LSM data	*/
 #endif
 	u32			consumed;
 } __randomize_layout;
@@ -47,12 +47,6 @@
 
 #define UNIXCB(skb)	(*(struct unix_skb_parms *)&((skb)->cb))
 
-#define unix_state_lock(s)	spin_lock(&unix_sk(s)->lock)
-#define unix_state_unlock(s)	spin_unlock(&unix_sk(s)->lock)
-#define unix_state_lock_nested(s) \
-				spin_lock_nested(&unix_sk(s)->lock, \
-				SINGLE_DEPTH_NESTING)
-
 /* The AF_UNIX socket */
 struct unix_sock {
 	/* WARNING: sk has to be the first member */
@@ -62,7 +56,7 @@
 	struct mutex		iolock, bindlock;
 	struct sock		*peer;
 	struct list_head	link;
-	atomic_long_t		inflight;
+	unsigned long		inflight;
 	spinlock_t		lock;
 	unsigned long		gc_flags;
 #define UNIX_GC_CANDIDATE	0
@@ -80,6 +74,23 @@
 	return (struct unix_sock *)sk;
 }
 
+#define unix_state_lock(s)	spin_lock(&unix_sk(s)->lock)
+#define unix_state_unlock(s)	spin_unlock(&unix_sk(s)->lock)
+enum unix_socket_lock_class {
+	U_LOCK_NORMAL,
+	U_LOCK_SECOND,	/* for double locking, see unix_state_double_lock(). */
+	U_LOCK_DIAG, /* used while dumping icons, see sk_diag_dump_icons(). */
+	U_LOCK_GC_LISTENER, /* used for listening socket while determining gc
+			     * candidates to close a small race window.
+			     */
+};
+
+static inline void unix_state_lock_nested(struct sock *sk,
+				   enum unix_socket_lock_class subclass)
+{
+	spin_lock_nested(&unix_sk(sk)->lock, subclass);
+}
+
 #define peer_wait peer_wq.wait
 
 long unix_inq_len(struct sock *sk);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/af_vsock.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/af_vsock.h
@@ -205,7 +205,8 @@
 struct sock *vsock_find_connected_socket(struct sockaddr_vm *src,
 					 struct sockaddr_vm *dst);
 void vsock_remove_sock(struct vsock_sock *vsk);
-void vsock_for_each_connected_socket(void (*fn)(struct sock *sk));
+void vsock_for_each_connected_socket(struct vsock_transport *transport,
+				     void (*fn)(struct sock *sk));
 int vsock_assign_transport(struct vsock_sock *vsk, struct vsock_sock *psk);
 bool vsock_find_cid(unsigned int cid);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/arp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/arp.h
@@ -71,6 +71,7 @@
 	      const unsigned char *src_hw, const unsigned char *th);
 int arp_mc_map(__be32 addr, u8 *haddr, struct net_device *dev, int dir);
 void arp_ifdown(struct net_device *dev);
+int arp_invalidate(struct net_device *dev, __be32 ip, bool force);
 
 struct sk_buff *arp_create(int type, int ptype, __be32 dest_ip,
 			   struct net_device *dev, __be32 src_ip,
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ax25.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ax25.h
@@ -236,6 +236,7 @@
 #if defined(CONFIG_AX25_DAMA_SLAVE) || defined(CONFIG_AX25_DAMA_MASTER)
 	ax25_dama_info		dama;
 #endif
+	refcount_t		refcount;
 } ax25_dev;
 
 typedef struct ax25_cb {
@@ -290,6 +291,17 @@
 	}
 }
 
+static inline void ax25_dev_hold(ax25_dev *ax25_dev)
+{
+	refcount_inc(&ax25_dev->refcount);
+}
+
+static inline void ax25_dev_put(ax25_dev *ax25_dev)
+{
+	if (refcount_dec_and_test(&ax25_dev->refcount)) {
+		kfree(ax25_dev);
+	}
+}
 static inline __be16 ax25_type_trans(struct sk_buff *skb, struct net_device *dev)
 {
 	skb->dev      = dev;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bluetooth/bluetooth.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bluetooth/bluetooth.h
@@ -180,19 +180,21 @@
 #define BT_DBG(fmt, ...)	pr_debug(fmt "\n", ##__VA_ARGS__)
 #endif
 
+#define bt_dev_name(hdev) ((hdev) ? (hdev)->name : "null")
+
 #define bt_dev_info(hdev, fmt, ...)				\
-	BT_INFO("%s: " fmt, (hdev)->name, ##__VA_ARGS__)
+	BT_INFO("%s: " fmt, bt_dev_name(hdev), ##__VA_ARGS__)
 #define bt_dev_warn(hdev, fmt, ...)				\
-	BT_WARN("%s: " fmt, (hdev)->name, ##__VA_ARGS__)
+	BT_WARN("%s: " fmt, bt_dev_name(hdev), ##__VA_ARGS__)
 #define bt_dev_err(hdev, fmt, ...)				\
-	BT_ERR("%s: " fmt, (hdev)->name, ##__VA_ARGS__)
+	BT_ERR("%s: " fmt, bt_dev_name(hdev), ##__VA_ARGS__)
 #define bt_dev_dbg(hdev, fmt, ...)				\
-	BT_DBG("%s: " fmt, (hdev)->name, ##__VA_ARGS__)
+	BT_DBG("%s: " fmt, bt_dev_name(hdev), ##__VA_ARGS__)
 
 #define bt_dev_warn_ratelimited(hdev, fmt, ...)			\
-	bt_warn_ratelimited("%s: " fmt, (hdev)->name, ##__VA_ARGS__)
+	bt_warn_ratelimited("%s: " fmt, bt_dev_name(hdev), ##__VA_ARGS__)
 #define bt_dev_err_ratelimited(hdev, fmt, ...)			\
-	bt_err_ratelimited("%s: " fmt, (hdev)->name, ##__VA_ARGS__)
+	bt_err_ratelimited("%s: " fmt, bt_dev_name(hdev), ##__VA_ARGS__)
 
 /* Connection and socket states */
 enum {
@@ -420,6 +422,80 @@
 	return NULL;
 }
 
+/* Shall not be called with lock_sock held */
+static inline struct sk_buff *bt_skb_sendmsg(struct sock *sk,
+					     struct msghdr *msg,
+					     size_t len, size_t mtu,
+					     size_t headroom, size_t tailroom)
+{
+	struct sk_buff *skb;
+	size_t size = min_t(size_t, len, mtu);
+	int err;
+
+	skb = bt_skb_send_alloc(sk, size + headroom + tailroom,
+				msg->msg_flags & MSG_DONTWAIT, &err);
+	if (!skb)
+		return ERR_PTR(err);
+
+	skb_reserve(skb, headroom);
+	skb_tailroom_reserve(skb, mtu, tailroom);
+
+	if (!copy_from_iter_full(skb_put(skb, size), size, &msg->msg_iter)) {
+		kfree_skb(skb);
+		return ERR_PTR(-EFAULT);
+	}
+
+	skb->priority = sk->sk_priority;
+
+	return skb;
+}
+
+/* Similar to bt_skb_sendmsg but can split the msg into multiple fragments
+ * accourding to the MTU.
+ */
+static inline struct sk_buff *bt_skb_sendmmsg(struct sock *sk,
+					      struct msghdr *msg,
+					      size_t len, size_t mtu,
+					      size_t headroom, size_t tailroom)
+{
+	struct sk_buff *skb, **frag;
+
+	skb = bt_skb_sendmsg(sk, msg, len, mtu, headroom, tailroom);
+	if (IS_ERR_OR_NULL(skb))
+		return skb;
+
+	len -= skb->len;
+	if (!len)
+		return skb;
+
+	/* Add remaining data over MTU as continuation fragments */
+	frag = &skb_shinfo(skb)->frag_list;
+	while (len) {
+		struct sk_buff *tmp;
+
+		tmp = bt_skb_sendmsg(sk, msg, len, mtu, headroom, tailroom);
+		if (IS_ERR(tmp)) {
+			return skb;
+		}
+
+		len -= tmp->len;
+
+		*frag = tmp;
+		frag = &(*frag)->next;
+	}
+
+	return skb;
+}
+
+static inline int bt_copy_from_sockptr(void *dst, size_t dst_size,
+				       sockptr_t src, size_t src_size)
+{
+	if (dst_size > src_size)
+		return -EINVAL;
+
+	return copy_from_sockptr(dst, src, dst_size);
+}
+
 int bt_to_errno(u16 code);
 
 void hci_sock_set_flag(struct sock *sk, int nr);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bluetooth/hci.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bluetooth/hci.h
@@ -246,6 +246,15 @@
 	 * HCI after resume.
 	 */
 	HCI_QUIRK_NO_SUSPEND_NOTIFIER,
+
+	/*
+	 * When this quirk is set, LE tx power is not queried on startup
+	 * and the min/max tx power values default to HCI_TX_POWER_INVALID.
+	 *
+	 * This quirk can be set before hci_register_dev is called or
+	 * during the hdev->setup vendor callback.
+	 */
+	HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER,
 };
 
 /* HCI device flags */
@@ -556,6 +565,7 @@
 #define HCI_ERROR_CONNECTION_TIMEOUT	0x08
 #define HCI_ERROR_REJ_LIMITED_RESOURCES	0x0d
 #define HCI_ERROR_REJ_BAD_ADDR		0x0f
+#define HCI_ERROR_INVALID_PARAMETERS	0x12
 #define HCI_ERROR_REMOTE_USER_TERM	0x13
 #define HCI_ERROR_REMOTE_LOW_RESOURCES	0x14
 #define HCI_ERROR_REMOTE_POWER_OFF	0x15
@@ -1432,6 +1442,15 @@
 	__u8     mask[8];
 } __packed;
 
+/* BLUETOOTH CORE SPECIFICATION Version 5.4 | Vol 4, Part E
+ * 7.8.2 LE Read Buffer Size command
+ * MAX_LE_MTU is 0xffff.
+ * 0 is also valid. It means that no dedicated LE Buffer exists.
+ * It should use the HCI_Read_Buffer_Size command and mtu is shared
+ * between BR/EDR and LE.
+ */
+#define HCI_MIN_LE_MTU 0x001b
+
 #define HCI_OP_LE_READ_BUFFER_SIZE	0x2002
 struct hci_rp_le_read_buffer_size {
 	__u8     status;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bluetooth/hci_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bluetooth/hci_core.h
@@ -35,6 +35,9 @@
 /* HCI priority */
 #define HCI_PRIO_MAX	7
 
+/* HCI maximum id value */
+#define HCI_MAX_ID 10000
+
 /* HCI Core structures */
 struct inquiry_data {
 	bdaddr_t	bdaddr;
@@ -307,7 +310,7 @@
 	struct list_head list;
 	struct mutex	lock;
 
-	char		name[8];
+	const char	*name;
 	unsigned long	flags;
 	__u16		id;
 	__u8		bus;
@@ -632,6 +635,7 @@
 	__u8		adv_instance;
 	__u16		handle;
 	__u16		state;
+	__u16		mtu;
 	__u8		mode;
 	__u8		type;
 	__u8		role;
@@ -844,7 +848,6 @@
 /* ----- HCI Connections ----- */
 enum {
 	HCI_CONN_AUTH_PEND,
-	HCI_CONN_REAUTH_PEND,
 	HCI_CONN_ENCRYPT_PEND,
 	HCI_CONN_RSWITCH_PEND,
 	HCI_CONN_MODE_CHANGE_PEND,
@@ -1683,18 +1686,46 @@
 {
 	u16 max_latency;
 
-	if (min > max || min < 6 || max > 3200)
+	if (min > max) {
+		BT_WARN("min %d > max %d", min, max);
 		return -EINVAL;
+	}
 
-	if (to_multiplier < 10 || to_multiplier > 3200)
+	if (min < 6) {
+		BT_WARN("min %d < 6", min);
 		return -EINVAL;
+	}
 
-	if (max >= to_multiplier * 8)
+	if (max > 3200) {
+		BT_WARN("max %d > 3200", max);
 		return -EINVAL;
+	}
+
+	if (to_multiplier < 10) {
+		BT_WARN("to_multiplier %d < 10", to_multiplier);
+		return -EINVAL;
+	}
+
+	if (to_multiplier > 3200) {
+		BT_WARN("to_multiplier %d > 3200", to_multiplier);
+		return -EINVAL;
+	}
+
+	if (max >= to_multiplier * 8) {
+		BT_WARN("max %d >= to_multiplier %d * 8", max, to_multiplier);
+		return -EINVAL;
+	}
 
 	max_latency = (to_multiplier * 4 / max) - 1;
-	if (latency > 499 || latency > max_latency)
+	if (latency > 499) {
+		BT_WARN("latency %d > 499", latency);
 		return -EINVAL;
+	}
+
+	if (latency > max_latency) {
+		BT_WARN("latency %d > max_latency %d", latency, max_latency);
+		return -EINVAL;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bluetooth/hci_mon.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bluetooth/hci_mon.h
@@ -56,7 +56,7 @@
 	__u8		type;
 	__u8		bus;
 	bdaddr_t	bdaddr;
-	char		name[8];
+	char		name[8] __nonstring;
 } __packed;
 #define HCI_MON_NEW_INDEX_SIZE 16
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bluetooth/l2cap.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bluetooth/l2cap.h
@@ -847,6 +847,7 @@
 };
 
 void l2cap_chan_hold(struct l2cap_chan *c);
+struct l2cap_chan *l2cap_chan_hold_unless_zero(struct l2cap_chan *c);
 void l2cap_chan_put(struct l2cap_chan *c);
 
 static inline void l2cap_chan_lock(struct l2cap_chan *chan)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bond_3ad.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bond_3ad.h
@@ -15,8 +15,6 @@
 #define PKT_TYPE_LACPDU         cpu_to_be16(ETH_P_SLOW)
 #define AD_TIMER_INTERVAL       100 /*msec*/
 
-#define MULTICAST_LACPDU_ADDR    {0x01, 0x80, 0xC2, 0x00, 0x00, 0x02}
-
 #define AD_LACP_SLOW 0
 #define AD_LACP_FAST 1
 
@@ -262,7 +260,7 @@
 struct ad_bond_info {
 	struct ad_system system;	/* 802.3ad system structure */
 	struct bond_3ad_stats stats;
-	u32 agg_select_timer;		/* Timer to select aggregator after all adapter's hand shakes */
+	atomic_t agg_select_timer;		/* Timer to select aggregator after all adapter's hand shakes */
 	u16 aggregator_identifier;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bond_alb.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bond_alb.h
@@ -126,7 +126,7 @@
 struct alb_bond_info {
 	struct tlb_client_info	*tx_hashtbl; /* Dynamically allocated */
 	u32			unbalanced_load;
-	int			tx_rebalance_counter;
+	atomic_t		tx_rebalance_counter;
 	int			lp_counter;
 	/* -------- rlb parameters -------- */
 	int rlb_enabled;
@@ -156,8 +156,8 @@
 void bond_alb_deinit_slave(struct bonding *bond, struct slave *slave);
 void bond_alb_handle_link_change(struct bonding *bond, struct slave *slave, char link);
 void bond_alb_handle_active_change(struct bonding *bond, struct slave *new_slave);
-int bond_alb_xmit(struct sk_buff *skb, struct net_device *bond_dev);
-int bond_tlb_xmit(struct sk_buff *skb, struct net_device *bond_dev);
+netdev_tx_t bond_alb_xmit(struct sk_buff *skb, struct net_device *bond_dev);
+netdev_tx_t bond_tlb_xmit(struct sk_buff *skb, struct net_device *bond_dev);
 struct slave *bond_xmit_alb_slave_get(struct bonding *bond,
 				      struct sk_buff *skb);
 struct slave *bond_xmit_tlb_slave_get(struct bonding *bond,
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bond_options.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bond_options.h
@@ -65,6 +65,7 @@
 	BOND_OPT_NUM_PEER_NOTIF_ALIAS,
 	BOND_OPT_PEER_NOTIF_DELAY,
 	BOND_OPT_LACP_ACTIVE,
+	BOND_OPT_MISSED_MAX,
 	BOND_OPT_LAST
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/bonding.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/bonding.h
@@ -121,6 +121,7 @@
 	int xmit_policy;
 	int miimon;
 	u8 num_peer_notif;
+	u8 missed_max;
 	int arp_interval;
 	int arp_validate;
 	int arp_all_targets;
@@ -214,6 +215,7 @@
 	struct   bond_up_slave __rcu *usable_slaves;
 	struct   bond_up_slave __rcu *all_slaves;
 	bool     force_primary;
+	bool     notifier_ctx;
 	s32      slave_cnt; /* never change this value outside the attach/detach wrappers */
 	int     (*recv_probe)(const struct sk_buff *, struct bonding *,
 			      struct slave *);
@@ -226,7 +228,7 @@
 	 */
 	spinlock_t mode_lock;
 	spinlock_t stats_lock;
-	u8	 send_peer_notif;
+	u32	 send_peer_notif;
 	u8       igmp_retrans;
 #ifdef CONFIG_PROC_FS
 	struct   proc_dir_entry *proc_entry;
@@ -698,37 +700,14 @@
 }
 
 /* Caller must hold rcu_read_lock() for read */
-static inline struct slave *bond_slave_has_mac_rcu(struct bonding *bond,
-					       const u8 *mac)
-{
-	struct list_head *iter;
-	struct slave *tmp;
-
-	bond_for_each_slave_rcu(bond, tmp, iter)
-		if (ether_addr_equal_64bits(mac, tmp->dev->dev_addr))
-			return tmp;
-
-	return NULL;
-}
-
-/* Caller must hold rcu_read_lock() for read */
-static inline bool bond_slave_has_mac_rx(struct bonding *bond, const u8 *mac)
+static inline bool bond_slave_has_mac_rcu(struct bonding *bond, const u8 *mac)
 {
 	struct list_head *iter;
 	struct slave *tmp;
-	struct netdev_hw_addr *ha;
 
 	bond_for_each_slave_rcu(bond, tmp, iter)
 		if (ether_addr_equal_64bits(mac, tmp->dev->dev_addr))
 			return true;
-
-	if (netdev_uc_empty(bond->dev))
-		return false;
-
-	netdev_for_each_uc_addr(ha, bond->dev)
-		if (ether_addr_equal_64bits(mac, ha->addr))
-			return true;
-
 	return false;
 }
 
@@ -757,6 +736,9 @@
 /* exported from bond_sysfs_slave.c */
 extern const struct sysfs_ops slave_sysfs_ops;
 
+/* exported from bond_3ad.c */
+extern const u8 lacpdu_mcast_addr[];
+
 static inline netdev_tx_t bond_tx_drop(struct net_device *dev, struct sk_buff *skb)
 {
 	atomic_long_inc(&dev->tx_dropped);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/busy_poll.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/busy_poll.h
@@ -33,7 +33,7 @@
 
 static inline bool net_busy_loop_on(void)
 {
-	return sysctl_net_busy_poll;
+	return READ_ONCE(sysctl_net_busy_poll);
 }
 
 static inline bool sk_can_busy_loop(const struct sock *sk)
@@ -63,7 +63,7 @@
 static inline unsigned long busy_loop_current_time(void)
 {
 #ifdef CONFIG_NET_RX_BUSY_POLL
-	return (unsigned long)(local_clock() >> 10);
+	return (unsigned long)(ktime_get_ns() >> 10);
 #else
 	return 0;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/cfg80211.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/cfg80211.h
@@ -510,6 +510,9 @@
 	if (WARN_ON(iftype >= NL80211_IFTYPE_MAX))
 		return NULL;
 
+	if (iftype == NL80211_IFTYPE_AP_VLAN)
+		iftype = NL80211_IFTYPE_AP;
+
 	for (i = 0; i < sband->n_iftype_data; i++)  {
 		const struct ieee80211_sband_iftype_data *data =
 			&sband->iftype_data[i];
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/cfg802154.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/cfg802154.h
@@ -257,6 +257,7 @@
 
 struct ieee802154_llsec_key_entry {
 	struct list_head list;
+	struct rcu_head rcu;
 
 	struct ieee802154_llsec_key_id id;
 	struct ieee802154_llsec_key *key;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/checksum.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/checksum.h
@@ -22,7 +22,7 @@
 #include <asm/checksum.h>
 
 #ifndef _HAVE_ARCH_COPY_AND_CSUM_FROM_USER
-static inline
+static __always_inline
 __wsum csum_and_copy_from_user (const void __user *src, void *dst,
 				      int len)
 {
@@ -33,7 +33,7 @@
 #endif
 
 #ifndef HAVE_CSUM_COPY_USER
-static __inline__ __wsum csum_and_copy_to_user
+static __always_inline __wsum csum_and_copy_to_user
 (const void *src, void __user *dst, int len)
 {
 	__wsum sum = csum_partial(src, len, ~0U);
@@ -45,7 +45,7 @@
 #endif
 
 #ifndef _HAVE_ARCH_CSUM_AND_COPY
-static inline __wsum
+static __always_inline __wsum
 csum_partial_copy_nocheck(const void *src, void *dst, int len)
 {
 	memcpy(dst, src, len);
@@ -54,7 +54,7 @@
 #endif
 
 #ifndef HAVE_ARCH_CSUM_ADD
-static inline __wsum csum_add(__wsum csum, __wsum addend)
+static __always_inline __wsum csum_add(__wsum csum, __wsum addend)
 {
 	u32 res = (__force u32)csum;
 	res += (__force u32)addend;
@@ -62,12 +62,12 @@
 }
 #endif
 
-static inline __wsum csum_sub(__wsum csum, __wsum addend)
+static __always_inline __wsum csum_sub(__wsum csum, __wsum addend)
 {
 	return csum_add(csum, ~addend);
 }
 
-static inline __sum16 csum16_add(__sum16 csum, __be16 addend)
+static __always_inline __sum16 csum16_add(__sum16 csum, __be16 addend)
 {
 	u16 res = (__force u16)csum;
 
@@ -75,12 +75,12 @@
 	return (__force __sum16)(res + (res < (__force u16)addend));
 }
 
-static inline __sum16 csum16_sub(__sum16 csum, __be16 addend)
+static __always_inline __sum16 csum16_sub(__sum16 csum, __be16 addend)
 {
 	return csum16_add(csum, ~addend);
 }
 
-static inline __wsum csum_shift(__wsum sum, int offset)
+static __always_inline __wsum csum_shift(__wsum sum, int offset)
 {
 	/* rotate sum to align it with a 16b boundary */
 	if (offset & 1)
@@ -88,42 +88,43 @@
 	return sum;
 }
 
-static inline __wsum
+static __always_inline __wsum
 csum_block_add(__wsum csum, __wsum csum2, int offset)
 {
 	return csum_add(csum, csum_shift(csum2, offset));
 }
 
-static inline __wsum
+static __always_inline __wsum
 csum_block_add_ext(__wsum csum, __wsum csum2, int offset, int len)
 {
 	return csum_block_add(csum, csum2, offset);
 }
 
-static inline __wsum
+static __always_inline __wsum
 csum_block_sub(__wsum csum, __wsum csum2, int offset)
 {
 	return csum_block_add(csum, ~csum2, offset);
 }
 
-static inline __wsum csum_unfold(__sum16 n)
+static __always_inline __wsum csum_unfold(__sum16 n)
 {
 	return (__force __wsum)n;
 }
 
-static inline __wsum csum_partial_ext(const void *buff, int len, __wsum sum)
+static __always_inline
+__wsum csum_partial_ext(const void *buff, int len, __wsum sum)
 {
 	return csum_partial(buff, len, sum);
 }
 
 #define CSUM_MANGLED_0 ((__force __sum16)0xffff)
 
-static inline void csum_replace_by_diff(__sum16 *sum, __wsum diff)
+static __always_inline void csum_replace_by_diff(__sum16 *sum, __wsum diff)
 {
 	*sum = csum_fold(csum_add(diff, ~csum_unfold(*sum)));
 }
 
-static inline void csum_replace4(__sum16 *sum, __be32 from, __be32 to)
+static __always_inline void csum_replace4(__sum16 *sum, __be32 from, __be32 to)
 {
 	__wsum tmp = csum_sub(~csum_unfold(*sum), (__force __wsum)from);
 
@@ -136,11 +137,16 @@
  *  m : old value of a 16bit field
  *  m' : new value of a 16bit field
  */
-static inline void csum_replace2(__sum16 *sum, __be16 old, __be16 new)
+static __always_inline void csum_replace2(__sum16 *sum, __be16 old, __be16 new)
 {
 	*sum = ~csum16_add(csum16_sub(~(*sum), old), new);
 }
 
+static inline void csum_replace(__wsum *csum, __wsum old, __wsum new)
+{
+	*csum = csum_add(csum_sub(*csum, old), new);
+}
+
 struct sk_buff;
 void inet_proto_csum_replace4(__sum16 *sum, struct sk_buff *skb,
 			      __be32 from, __be32 to, bool pseudohdr);
@@ -150,16 +156,16 @@
 void inet_proto_csum_replace_by_diff(__sum16 *sum, struct sk_buff *skb,
 				     __wsum diff, bool pseudohdr);
 
-static inline void inet_proto_csum_replace2(__sum16 *sum, struct sk_buff *skb,
-					    __be16 from, __be16 to,
-					    bool pseudohdr)
+static __always_inline
+void inet_proto_csum_replace2(__sum16 *sum, struct sk_buff *skb,
+			      __be16 from, __be16 to, bool pseudohdr)
 {
 	inet_proto_csum_replace4(sum, skb, (__force __be32)from,
 				 (__force __be32)to, pseudohdr);
 }
 
-static inline __wsum remcsum_adjust(void *ptr, __wsum csum,
-				    int start, int offset)
+static __always_inline __wsum remcsum_adjust(void *ptr, __wsum csum,
+					     int start, int offset)
 {
 	__sum16 *psum = (__sum16 *)(ptr + offset);
 	__wsum delta;
@@ -175,7 +181,7 @@
 	return delta;
 }
 
-static inline void remcsum_unadjust(__sum16 *psum, __wsum delta)
+static __always_inline void remcsum_unadjust(__sum16 *psum, __wsum delta)
 {
 	*psum = csum_fold(csum_sub(delta, (__force __wsum)*psum));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/dsa.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/dsa.h
@@ -472,6 +472,34 @@
 	return dsa_to_port(ds, p)->type == DSA_PORT_TYPE_USER;
 }
 
+#define dsa_tree_for_each_user_port(_dp, _dst) \
+	list_for_each_entry((_dp), &(_dst)->ports, list) \
+		if (dsa_port_is_user((_dp)))
+
+#define dsa_switch_for_each_port(_dp, _ds) \
+	list_for_each_entry((_dp), &(_ds)->dst->ports, list) \
+		if ((_dp)->ds == (_ds))
+
+#define dsa_switch_for_each_port_safe(_dp, _next, _ds) \
+	list_for_each_entry_safe((_dp), (_next), &(_ds)->dst->ports, list) \
+		if ((_dp)->ds == (_ds))
+
+#define dsa_switch_for_each_port_continue_reverse(_dp, _ds) \
+	list_for_each_entry_continue_reverse((_dp), &(_ds)->dst->ports, list) \
+		if ((_dp)->ds == (_ds))
+
+#define dsa_switch_for_each_available_port(_dp, _ds) \
+	dsa_switch_for_each_port((_dp), (_ds)) \
+		if (!dsa_port_is_unused((_dp)))
+
+#define dsa_switch_for_each_user_port(_dp, _ds) \
+	dsa_switch_for_each_port((_dp), (_ds)) \
+		if (dsa_port_is_user((_dp)))
+
+#define dsa_switch_for_each_cpu_port(_dp, _ds) \
+	dsa_switch_for_each_port((_dp), (_ds)) \
+		if (dsa_port_is_cpu((_dp)))
+
 static inline u32 dsa_user_ports(struct dsa_switch *ds)
 {
 	u32 mask = 0;
@@ -665,6 +693,17 @@
 			       struct ethtool_ts_info *ts);
 
 	/*
+	 * ethtool MAC merge layer
+	 */
+	int	(*get_mm)(struct dsa_switch *ds, int port,
+			  struct ethtool_mm_state *state);
+	int	(*set_mm)(struct dsa_switch *ds, int port,
+			  struct ethtool_mm_cfg *cfg,
+			  struct netlink_ext_ack *extack);
+	void	(*get_mm_stats)(struct dsa_switch *ds, int port,
+				struct ethtool_mm_stats *stats);
+
+	/*
 	 * Suspend and resume
 	 */
 	int	(*suspend)(struct dsa_switch *ds);
@@ -678,6 +717,14 @@
 	void	(*port_disable)(struct dsa_switch *ds, int port);
 
 	/*
+	 * Compatibility between device trees defining multiple CPU ports and
+	 * drivers which are not OK to use by default the numerically smallest
+	 * CPU port of a switch for its local ports. This can return NULL,
+	 * meaning "don't know/don't care".
+	 */
+	struct dsa_port *(*preferred_default_local_cpu_port)(struct dsa_switch *ds);
+
+	/*
 	 * Port's MAC EEE settings
 	 */
 	int	(*set_mac_eee)(struct dsa_switch *ds, int port,
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/dst.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/dst.h
@@ -238,12 +238,6 @@
 	}
 }
 
-static inline void dst_hold_and_use(struct dst_entry *dst, unsigned long time)
-{
-	dst_hold(dst);
-	dst_use_noref(dst, time);
-}
-
 static inline struct dst_entry *dst_clone(struct dst_entry *dst)
 {
 	if (dst)
@@ -361,9 +355,8 @@
 static inline void skb_tunnel_rx(struct sk_buff *skb, struct net_device *dev,
 				 struct net *net)
 {
-	/* TODO : stats should be SMP safe */
-	dev->stats.rx_packets++;
-	dev->stats.rx_bytes += skb->len;
+	DEV_STATS_INC(dev, rx_packets);
+	DEV_STATS_ADD(dev, rx_bytes, skb->len);
 	__skb_tunnel_rx(skb, dev, net);
 }
 
@@ -440,6 +433,15 @@
 		dst->expires = expires;
 }
 
+static inline unsigned int dst_dev_overhead(struct dst_entry *dst,
+					    struct sk_buff *skb)
+{
+	if (likely(dst))
+		return LL_RESERVED_SPACE(dst->dev);
+
+	return skb->mac_len;
+}
+
 INDIRECT_CALLABLE_DECLARE(int ip6_output(struct net *, struct sock *,
 					 struct sk_buff *));
 INDIRECT_CALLABLE_DECLARE(int ip_output(struct net *, struct sock *,
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/dst_cache.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/dst_cache.h
@@ -80,6 +80,17 @@
 }
 
 /**
+ *	dst_cache_reset_now - invalidate the cache contents immediately
+ *	@dst_cache: the cache
+ *
+ *	The caller must be sure there are no concurrent users, as this frees
+ *	all dst_cache users immediately, rather than waiting for the next
+ *	per-cpu usage like dst_cache_reset does. Most callers should use the
+ *	higher speed lazily-freed dst_cache_reset function instead.
+ */
+void dst_cache_reset_now(struct dst_cache *dst_cache);
+
+/**
  *	dst_cache_init - initialize the cache, allocating the required storage
  *	@dst_cache: the cache
  *	@gfp: allocation flags
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/dst_metadata.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/dst_metadata.h
@@ -123,8 +123,20 @@
 
 	memcpy(&new_md->u.tun_info, &md_dst->u.tun_info,
 	       sizeof(struct ip_tunnel_info) + md_size);
+#ifdef CONFIG_DST_CACHE
+	/* Unclone the dst cache if there is one */
+	if (new_md->u.tun_info.dst_cache.cache) {
+		int ret;
+
+		ret = dst_cache_init(&new_md->u.tun_info.dst_cache, GFP_ATOMIC);
+		if (ret) {
+			metadata_dst_free(new_md);
+			return ERR_PTR(ret);
+		}
+	}
+#endif
+
 	skb_dst_drop(skb);
-	dst_hold(&new_md->dst);
 	skb_dst_set(skb, &new_md->dst);
 	return new_md;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/dst_ops.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/dst_ops.h
@@ -16,7 +16,7 @@
 	unsigned short		family;
 	unsigned int		gc_thresh;
 
-	int			(*gc)(struct dst_ops *ops);
+	void			(*gc)(struct dst_ops *ops);
 	struct dst_entry *	(*check)(struct dst_entry *, __u32 cookie);
 	unsigned int		(*default_advmss)(const struct dst_entry *);
 	unsigned int		(*mtu)(const struct dst_entry *);
@@ -24,7 +24,7 @@
 	void			(*destroy)(struct dst_entry *);
 	void			(*ifdown)(struct dst_entry *,
 					  struct net_device *dev, int how);
-	struct dst_entry *	(*negative_advice)(struct dst_entry *);
+	void			(*negative_advice)(struct sock *sk, struct dst_entry *);
 	void			(*link_failure)(struct sk_buff *);
 	void			(*update_pmtu)(struct dst_entry *dst, struct sock *sk,
 					       struct sk_buff *skb, u32 mtu,
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/fib_rules.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/fib_rules.h
@@ -69,7 +69,7 @@
 	int			(*action)(struct fib_rule *,
 					  struct flowi *, int,
 					  struct fib_lookup_arg *);
-	bool			(*suppress)(struct fib_rule *,
+	bool			(*suppress)(struct fib_rule *, int,
 					    struct fib_lookup_arg *);
 	int			(*match)(struct fib_rule *,
 					 struct flowi *, int);
@@ -218,7 +218,9 @@
 			    struct fib_lookup_arg *arg));
 
 INDIRECT_CALLABLE_DECLARE(bool fib6_rule_suppress(struct fib_rule *rule,
+						int flags,
 						struct fib_lookup_arg *arg));
 INDIRECT_CALLABLE_DECLARE(bool fib4_rule_suppress(struct fib_rule *rule,
+						int flags,
 						struct fib_lookup_arg *arg));
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/flow.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/flow.h
@@ -29,6 +29,7 @@
 struct flowi_common {
 	int	flowic_oif;
 	int	flowic_iif;
+	int     flowic_l3mdev;
 	__u32	flowic_mark;
 	__u8	flowic_tos;
 	__u8	flowic_scope;
@@ -36,11 +37,10 @@
 	__u8	flowic_flags;
 #define FLOWI_FLAG_ANYSRC		0x01
 #define FLOWI_FLAG_KNOWN_NH		0x02
-#define FLOWI_FLAG_SKIP_NH_OIF		0x04
 	__u32	flowic_secid;
 	kuid_t  flowic_uid;
-	struct flowi_tunnel flowic_tun_key;
 	__u32		flowic_multipath_hash;
+	struct flowi_tunnel flowic_tun_key;
 };
 
 union flowi_uli {
@@ -54,11 +54,6 @@
 		__u8	code;
 	} icmpt;
 
-	struct {
-		__le16	dport;
-		__le16	sport;
-	} dnports;
-
 	__be32		gre_key;
 
 	struct {
@@ -70,6 +65,7 @@
 	struct flowi_common	__fl_common;
 #define flowi4_oif		__fl_common.flowic_oif
 #define flowi4_iif		__fl_common.flowic_iif
+#define flowi4_l3mdev		__fl_common.flowic_l3mdev
 #define flowi4_mark		__fl_common.flowic_mark
 #define flowi4_tos		__fl_common.flowic_tos
 #define flowi4_scope		__fl_common.flowic_scope
@@ -102,6 +98,7 @@
 {
 	fl4->flowi4_oif = oif;
 	fl4->flowi4_iif = LOOPBACK_IFINDEX;
+	fl4->flowi4_l3mdev = 0;
 	fl4->flowi4_mark = mark;
 	fl4->flowi4_tos = tos;
 	fl4->flowi4_scope = scope;
@@ -132,6 +129,7 @@
 	struct flowi_common	__fl_common;
 #define flowi6_oif		__fl_common.flowic_oif
 #define flowi6_iif		__fl_common.flowic_iif
+#define flowi6_l3mdev		__fl_common.flowic_l3mdev
 #define flowi6_mark		__fl_common.flowic_mark
 #define flowi6_scope		__fl_common.flowic_scope
 #define flowi6_proto		__fl_common.flowic_proto
@@ -153,30 +151,15 @@
 	__u32			mp_hash;
 } __attribute__((__aligned__(BITS_PER_LONG/8)));
 
-struct flowidn {
-	struct flowi_common	__fl_common;
-#define flowidn_oif		__fl_common.flowic_oif
-#define flowidn_iif		__fl_common.flowic_iif
-#define flowidn_mark		__fl_common.flowic_mark
-#define flowidn_scope		__fl_common.flowic_scope
-#define flowidn_proto		__fl_common.flowic_proto
-#define flowidn_flags		__fl_common.flowic_flags
-	__le16			daddr;
-	__le16			saddr;
-	union flowi_uli		uli;
-#define fld_sport		uli.ports.sport
-#define fld_dport		uli.ports.dport
-} __attribute__((__aligned__(BITS_PER_LONG/8)));
-
 struct flowi {
 	union {
 		struct flowi_common	__fl_common;
 		struct flowi4		ip4;
 		struct flowi6		ip6;
-		struct flowidn		dn;
 	} u;
 #define flowi_oif	u.__fl_common.flowic_oif
 #define flowi_iif	u.__fl_common.flowic_iif
+#define flowi_l3mdev	u.__fl_common.flowic_l3mdev
 #define flowi_mark	u.__fl_common.flowic_mark
 #define flowi_tos	u.__fl_common.flowic_tos
 #define flowi_scope	u.__fl_common.flowic_scope
@@ -207,11 +190,6 @@
 	return &(fl6->__fl_common);
 }
 
-static inline struct flowi *flowidn_to_flowi(struct flowidn *fldn)
-{
-	return container_of(fldn, struct flowi, u.dn);
-}
-
 __u32 __get_hash_from_flowi6(const struct flowi6 *fl6, struct flow_keys *keys);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/flow_dissector.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/flow_dissector.h
@@ -59,6 +59,8 @@
 		__be16	vlan_tci;
 	};
 	__be16	vlan_tpid;
+	__be16	vlan_eth_type;
+	u16	padding;
 };
 
 struct flow_dissector_mpls_lse {
@@ -175,6 +177,22 @@
 		};
 	};
 };
+
+/**
+ * struct flow_dissector_key_ports_range
+ * @tp: port number from packet
+ * @tp_min: min port number in range
+ * @tp_max: max port number in range
+ */
+struct flow_dissector_key_ports_range {
+	union {
+		struct flow_dissector_key_ports tp;
+		struct {
+			struct flow_dissector_key_ports tp_min;
+			struct flow_dissector_key_ports tp_max;
+		};
+	};
+};
 
 /**
  * flow_dissector_key_icmp:
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/flow_offload.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/flow_offload.h
@@ -48,6 +48,10 @@
 	struct flow_dissector_key_ports *key, *mask;
 };
 
+struct flow_match_ports_range {
+	struct flow_dissector_key_ports_range *key, *mask;
+};
+
 struct flow_match_icmp {
 	struct flow_dissector_key_icmp *key, *mask;
 };
@@ -94,6 +98,8 @@
 			struct flow_match_ip *out);
 void flow_rule_match_ports(const struct flow_rule *rule,
 			   struct flow_match_ports *out);
+void flow_rule_match_ports_range(const struct flow_rule *rule,
+				 struct flow_match_ports_range *out);
 void flow_rule_match_tcp(const struct flow_rule *rule,
 			 struct flow_match_tcp *out);
 void flow_rule_match_icmp(const struct flow_rule *rule,
@@ -575,5 +581,6 @@
 				enum tc_setup_type type, void *data,
 				struct flow_block_offload *bo,
 				void (*cleanup)(struct flow_block_cb *block_cb));
+bool flow_indr_dev_exists(void);
 
 #endif /* _NET_FLOW_OFFLOAD_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/genetlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/genetlink.h
@@ -11,10 +11,13 @@
 /**
  * struct genl_multicast_group - generic netlink multicast group
  * @name: name of the multicast group, names are per-family
+ * @flags: GENL_* flags (%GENL_ADMIN_PERM or %GENL_UNS_ADMIN_PERM)
+ * @cap_sys_admin: whether %CAP_SYS_ADMIN is required for binding
  */
 struct genl_multicast_group {
 	char			name[GENL_NAMSIZ];
 	u8			flags;
+	u8			cap_sys_admin:1;
 };
 
 struct genl_ops;
@@ -116,7 +119,7 @@
  * struct genl_small_ops - generic netlink operations (small version)
  * @cmd: command identifier
  * @internal_flags: flags used by the family
- * @flags: flags
+ * @flags: GENL_* flags (%GENL_ADMIN_PERM or %GENL_UNS_ADMIN_PERM)
  * @validate: validation flags from enum genl_validate_flags
  * @doit: standard command callback
  * @dumpit: callback for dumpers
@@ -137,7 +140,7 @@
  * struct genl_ops - generic netlink operations
  * @cmd: command identifier
  * @internal_flags: flags used by the family
- * @flags: flags
+ * @flags: GENL_* flags (%GENL_ADMIN_PERM or %GENL_UNS_ADMIN_PERM)
  * @maxattr: maximum number of attributes supported
  * @policy: netlink policy (takes precedence over family policy)
  * @validate: validation flags from enum genl_validate_flags
@@ -333,13 +336,12 @@
  * @skb: netlink message as socket buffer
  * @portid: own netlink portid to avoid sending to yourself
  * @group: offset of multicast group in groups array
- * @flags: allocation flags
  *
  * This function must hold the RTNL or rcu_read_lock().
  */
 int genlmsg_multicast_allns(const struct genl_family *family,
 			    struct sk_buff *skb, u32 portid,
-			    unsigned int group, gfp_t flags);
+			    unsigned int group);
 
 /**
  * genlmsg_unicast - unicast a netlink message
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ieee802154_netdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ieee802154_netdev.h
@@ -15,6 +15,22 @@
 #ifndef IEEE802154_NETDEVICE_H
 #define IEEE802154_NETDEVICE_H
 
+#define IEEE802154_REQUIRED_SIZE(struct_type, member) \
+	(offsetof(typeof(struct_type), member) + \
+	sizeof(((typeof(struct_type) *)(NULL))->member))
+
+#define IEEE802154_ADDR_OFFSET \
+	offsetof(typeof(struct sockaddr_ieee802154), addr)
+
+#define IEEE802154_MIN_NAMELEN (IEEE802154_ADDR_OFFSET + \
+	IEEE802154_REQUIRED_SIZE(struct ieee802154_addr_sa, addr_type))
+
+#define IEEE802154_NAMELEN_SHORT (IEEE802154_ADDR_OFFSET + \
+	IEEE802154_REQUIRED_SIZE(struct ieee802154_addr_sa, short_addr))
+
+#define IEEE802154_NAMELEN_LONG (IEEE802154_ADDR_OFFSET + \
+	IEEE802154_REQUIRED_SIZE(struct ieee802154_addr_sa, hwaddr))
+
 #include <net/af_ieee802154.h>
 #include <linux/netdevice.h>
 #include <linux/skbuff.h>
@@ -165,6 +181,33 @@
 	memcpy(raw, &temp, IEEE802154_ADDR_LEN);
 }
 
+static inline int
+ieee802154_sockaddr_check_size(struct sockaddr_ieee802154 *daddr, int len)
+{
+	struct ieee802154_addr_sa *sa;
+	int ret = 0;
+
+	sa = &daddr->addr;
+	if (len < IEEE802154_MIN_NAMELEN)
+		return -EINVAL;
+	switch (sa->addr_type) {
+	case IEEE802154_ADDR_NONE:
+		break;
+	case IEEE802154_ADDR_SHORT:
+		if (len < IEEE802154_NAMELEN_SHORT)
+			ret = -EINVAL;
+		break;
+	case IEEE802154_ADDR_LONG:
+		if (len < IEEE802154_NAMELEN_LONG)
+			ret = -EINVAL;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+	return ret;
+}
+
 static inline void ieee802154_addr_from_sa(struct ieee802154_addr *a,
 					   const struct ieee802154_addr_sa *sa)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/if_inet6.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/if_inet6.h
@@ -22,10 +22,6 @@
 #define IF_RS_SENT	0x10
 #define IF_READY	0x80000000
 
-/* prefix flags */
-#define IF_PREFIX_ONLINK	0x01
-#define IF_PREFIX_AUTOCONF	0x02
-
 enum {
 	INET6_IFADDR_STATE_PREDAD,
 	INET6_IFADDR_STATE_DAD,
@@ -64,6 +60,14 @@
 
 	struct hlist_node	addr_lst;
 	struct list_head	if_list;
+	/*
+	 * Used to safely traverse idev->addr_list in process context
+	 * if the idev->lock needed to protect idev->addr_list cannot be held.
+	 * In that case, add the items to this list temporarily and iterate
+	 * without holding idev->lock.
+	 * See addrconf_ifdown and dev_forward_change.
+	 */
+	struct list_head	if_list_aux;
 
 	struct list_head	tmp_list;
 	struct inet6_ifaddr	*ifpub;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/inet6_hashtables.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/inet6_hashtables.h
@@ -48,6 +48,22 @@
 					const u16 hnum, const int dif,
 					const int sdif);
 
+typedef u32 (inet6_ehashfn_t)(const struct net *net,
+			       const struct in6_addr *laddr, const u16 lport,
+			       const struct in6_addr *faddr, const __be16 fport);
+
+inet6_ehashfn_t inet6_ehashfn;
+
+INDIRECT_CALLABLE_DECLARE(inet6_ehashfn_t udp6_ehashfn);
+
+struct sock *inet6_lookup_reuseport(struct net *net, struct sock *sk,
+				    struct sk_buff *skb, int doff,
+				    const struct in6_addr *saddr,
+				    __be16 sport,
+				    const struct in6_addr *daddr,
+				    unsigned short hnum,
+				    inet6_ehashfn_t *ehashfn);
+
 struct sock *inet6_lookup_listener(struct net *net,
 				   struct inet_hashinfo *hashinfo,
 				   struct sk_buff *skb, int doff,
@@ -103,15 +119,24 @@
 			  const int dif);
 
 int inet6_hash(struct sock *sk);
-#endif /* IS_ENABLED(CONFIG_IPV6) */
 
-#define INET6_MATCH(__sk, __net, __saddr, __daddr, __ports, __dif, __sdif) \
-	(((__sk)->sk_portpair == (__ports))			&&	\
-	 ((__sk)->sk_family == AF_INET6)			&&	\
-	 ipv6_addr_equal(&(__sk)->sk_v6_daddr, (__saddr))		&&	\
-	 ipv6_addr_equal(&(__sk)->sk_v6_rcv_saddr, (__daddr))	&&	\
-	 (((__sk)->sk_bound_dev_if == (__dif))	||			\
-	  ((__sk)->sk_bound_dev_if == (__sdif)))		&&	\
-	 net_eq(sock_net(__sk), (__net)))
+static inline bool inet6_match(struct net *net, const struct sock *sk,
+			       const struct in6_addr *saddr,
+			       const struct in6_addr *daddr,
+			       const __portpair ports,
+			       const int dif, const int sdif)
+{
+	if (!net_eq(sock_net(sk), net) ||
+	    sk->sk_family != AF_INET6 ||
+	    sk->sk_portpair != ports ||
+	    !ipv6_addr_equal(&sk->sk_v6_daddr, saddr) ||
+	    !ipv6_addr_equal(&sk->sk_v6_rcv_saddr, daddr))
+		return false;
+
+	/* READ_ONCE() paired with WRITE_ONCE() in sock_bindtoindex_locked() */
+	return inet_sk_bound_dev_eq(net, READ_ONCE(sk->sk_bound_dev_if), dif,
+				    sdif);
+}
+#endif /* IS_ENABLED(CONFIG_IPV6) */
 
 #endif /* _INET6_HASHTABLES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/inet_connection_sock.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/inet_connection_sock.h
@@ -66,7 +66,6 @@
  * @icsk_ulp_ops	   Pluggable ULP control hook
  * @icsk_ulp_data	   ULP private data
  * @icsk_clean_acked	   Clean acked data hook
- * @icsk_listen_portaddr_node	hash to the portaddr listener hashtable
  * @icsk_ca_state:	   Congestion control state
  * @icsk_retransmits:	   Number of unrecovered [RTO] timeouts
  * @icsk_pending:	   Scheduled timer event
@@ -96,7 +95,6 @@
 	const struct tcp_ulp_ops  *icsk_ulp_ops;
 	void __rcu		  *icsk_ulp_data;
 	void (*icsk_clean_acked)(struct sock *sk, u32 acked_seq);
-	struct hlist_node         icsk_listen_portaddr_node;
 	unsigned int		  (*icsk_sync_mss)(struct sock *sk, u32 pmtu);
 	__u8			  icsk_ca_state:5,
 				  icsk_ca_initialized:1,
@@ -171,6 +169,7 @@
 			       void (*delack_handler)(struct timer_list *),
 			       void (*keepalive_handler)(struct timer_list *));
 void inet_csk_clear_xmit_timers(struct sock *sk);
+void inet_csk_clear_xmit_timers_sync(struct sock *sk);
 
 static inline void inet_csk_schedule_ack(struct sock *sk)
 {
@@ -261,7 +260,7 @@
 struct sock *inet_csk_reqsk_queue_add(struct sock *sk,
 				      struct request_sock *req,
 				      struct sock *child);
-void inet_csk_reqsk_queue_hash_add(struct sock *sk, struct request_sock *req,
+bool inet_csk_reqsk_queue_hash_add(struct sock *sk, struct request_sock *req,
 				   unsigned long timeout);
 struct sock *inet_csk_complete_hashdance(struct sock *sk, struct sock *child,
 					 struct request_sock *req,
@@ -279,17 +278,25 @@
 
 static inline int inet_csk_reqsk_queue_is_full(const struct sock *sk)
 {
-	return inet_csk_reqsk_queue_len(sk) >= sk->sk_max_ack_backlog;
+	return inet_csk_reqsk_queue_len(sk) > READ_ONCE(sk->sk_max_ack_backlog);
 }
 
 bool inet_csk_reqsk_queue_drop(struct sock *sk, struct request_sock *req);
 void inet_csk_reqsk_queue_drop_and_put(struct sock *sk, struct request_sock *req);
 
+static inline unsigned long
+reqsk_timeout(struct request_sock *req, unsigned long max_timeout)
+{
+	u64 timeout = (u64)req->timeout << req->num_timeout;
+
+	return (unsigned long)min_t(u64, timeout, max_timeout);
+}
+
 static inline void inet_csk_prepare_for_destroy_sock(struct sock *sk)
 {
 	/* The below has to be done to allow calling inet_csk_destroy_sock */
 	sock_set_flag(sk, SOCK_DEAD);
-	percpu_counter_inc(sk->sk_prot->orphan_count);
+	this_cpu_inc(*sk->sk_prot->orphan_count);
 }
 
 void inet_csk_destroy_sock(struct sock *sk);
@@ -315,7 +322,7 @@
 
 struct dst_entry *inet_csk_update_pmtu(struct sock *sk, u32 mtu);
 
-#define TCP_PINGPONG_THRESH	3
+#define TCP_PINGPONG_THRESH	1
 
 static inline void inet_csk_enter_pingpong_mode(struct sock *sk)
 {
@@ -332,17 +339,17 @@
 	return inet_csk(sk)->icsk_ack.pingpong >= TCP_PINGPONG_THRESH;
 }
 
-static inline void inet_csk_inc_pingpong_cnt(struct sock *sk)
+static inline bool inet_csk_has_ulp(struct sock *sk)
 {
-	struct inet_connection_sock *icsk = inet_csk(sk);
-
-	if (icsk->icsk_ack.pingpong < U8_MAX)
-		icsk->icsk_ack.pingpong++;
+	return inet_sk(sk)->is_icsk && !!inet_csk(sk)->icsk_ulp_ops;
 }
 
-static inline bool inet_csk_has_ulp(struct sock *sk)
+static inline void inet_init_csk_locks(struct sock *sk)
 {
-	return inet_sk(sk)->is_icsk && !!inet_csk(sk)->icsk_ulp_ops;
+	struct inet_connection_sock *icsk = inet_csk(sk);
+
+	spin_lock_init(&icsk->icsk_accept_queue.rskq_lock);
+	spin_lock_init(&icsk->icsk_accept_queue.fastopenq.lock);
 }
 
 #endif /* _INET_CONNECTION_SOCK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/inet_frag.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/inet_frag.h
@@ -117,8 +117,15 @@
 
 static inline void fqdir_pre_exit(struct fqdir *fqdir)
 {
-	fqdir->high_thresh = 0; /* prevent creation of new frags */
-	fqdir->dead = true;
+	/* Prevent creation of new frags.
+	 * Pairs with READ_ONCE() in inet_frag_find().
+	 */
+	WRITE_ONCE(fqdir->high_thresh, 0);
+
+	/* Pairs with READ_ONCE() in inet_frag_kill(), ip_expire()
+	 * and ip6frag_expire_frag_queue().
+	 */
+	WRITE_ONCE(fqdir->dead, true);
 }
 void fqdir_exit(struct fqdir *fqdir);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/inet_hashtables.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/inet_hashtables.h
@@ -111,11 +111,7 @@
 #define LISTENING_NULLS_BASE (1U << 29)
 struct inet_listen_hashbucket {
 	spinlock_t		lock;
-	unsigned int		count;
-	union {
-		struct hlist_head	head;
-		struct hlist_nulls_head	nulls_head;
-	};
+	struct hlist_nulls_head	nulls_head;
 };
 
 /* This is for listening sockets, thus all sockets which possess wildcards. */
@@ -143,32 +139,8 @@
 	/* The 2nd listener table hashed by local port and address */
 	unsigned int			lhash2_mask;
 	struct inet_listen_hashbucket	*lhash2;
-
-	/* All the above members are written once at bootup and
-	 * never written again _or_ are predominantly read-access.
-	 *
-	 * Now align to a new cache line as all the following members
-	 * might be often dirty.
-	 */
-	/* All sockets in TCP_LISTEN state will be in listening_hash.
-	 * This is the only table where wildcard'd TCP sockets can
-	 * exist.  listening_hash is only hashed by local port number.
-	 * If lhash2 is initialized, the same socket will also be hashed
-	 * to lhash2 by port and address.
-	 */
-	struct inet_listen_hashbucket	listening_hash[INET_LHTABLE_SIZE]
-					____cacheline_aligned_in_smp;
 };
 
-#define inet_lhash2_for_each_icsk_continue(__icsk) \
-	hlist_for_each_entry_continue(__icsk, icsk_listen_portaddr_node)
-
-#define inet_lhash2_for_each_icsk(__icsk, list) \
-	hlist_for_each_entry(__icsk, list, icsk_listen_portaddr_node)
-
-#define inet_lhash2_for_each_icsk_rcu(__icsk, list) \
-	hlist_for_each_entry_rcu(__icsk, list, icsk_listen_portaddr_node)
-
 static inline struct inet_listen_hashbucket *
 inet_lhash2_bucket(struct inet_hashinfo *h, u32 hash)
 {
@@ -203,17 +175,6 @@
 	hashinfo->ehash_locks = NULL;
 }
 
-static inline bool inet_sk_bound_dev_eq(struct net *net, int bound_dev_if,
-					int dif, int sdif)
-{
-#if IS_ENABLED(CONFIG_NET_L3_MASTER_DEV)
-	return inet_bound_dev_eq(!!net->ipv4.sysctl_tcp_l3mdev_accept,
-				 bound_dev_if, dif, sdif);
-#else
-	return inet_bound_dev_eq(true, bound_dev_if, dif, sdif);
-#endif
-}
-
 struct inet_bind_bucket *
 inet_bind_bucket_create(struct kmem_cache *cachep, struct net *net,
 			struct inet_bind_hashbucket *head,
@@ -230,23 +191,11 @@
 void inet_bind_hash(struct sock *sk, struct inet_bind_bucket *tb,
 		    const unsigned short snum);
 
-/* These can have wildcards, don't try too hard. */
-static inline u32 inet_lhashfn(const struct net *net, const unsigned short num)
-{
-	return (num + net_hash_mix(net)) & (INET_LHTABLE_SIZE - 1);
-}
-
-static inline int inet_sk_listen_hashfn(const struct sock *sk)
-{
-	return inet_lhashfn(sock_net(sk), inet_sk(sk)->inet_num);
-}
-
 /* Caller must disable local BH processing. */
 int __inet_inherit_port(const struct sock *sk, struct sock *child);
 
 void inet_put_port(struct sock *sk);
 
-void inet_hashinfo_init(struct inet_hashinfo *h);
 void inet_hashinfo2_init(struct inet_hashinfo *h, const char *name,
 			 unsigned long numentries, int scale,
 			 unsigned long low_limit,
@@ -295,7 +244,6 @@
 	((__force __portpair)(((__u32)(__dport) << 16) | (__force __u32)(__be16)(__sport)))
 #endif
 
-#if (BITS_PER_LONG == 64)
 #ifdef __BIG_ENDIAN
 #define INET_ADDR_COOKIE(__name, __saddr, __daddr) \
 	const __addrpair __name = (__force __addrpair) ( \
@@ -307,24 +255,20 @@
 				   (((__force __u64)(__be32)(__daddr)) << 32) | \
 				   ((__force __u64)(__be32)(__saddr)))
 #endif /* __BIG_ENDIAN */
-#define INET_MATCH(__sk, __net, __cookie, __saddr, __daddr, __ports, __dif, __sdif) \
-	(((__sk)->sk_portpair == (__ports))			&&	\
-	 ((__sk)->sk_addrpair == (__cookie))			&&	\
-	 (((__sk)->sk_bound_dev_if == (__dif))			||	\
-	  ((__sk)->sk_bound_dev_if == (__sdif)))		&&	\
-	 net_eq(sock_net(__sk), (__net)))
-#else /* 32-bit arch */
-#define INET_ADDR_COOKIE(__name, __saddr, __daddr) \
-	const int __name __deprecated __attribute__((unused))
 
-#define INET_MATCH(__sk, __net, __cookie, __saddr, __daddr, __ports, __dif, __sdif) \
-	(((__sk)->sk_portpair == (__ports))		&&		\
-	 ((__sk)->sk_daddr	== (__saddr))		&&		\
-	 ((__sk)->sk_rcv_saddr	== (__daddr))		&&		\
-	 (((__sk)->sk_bound_dev_if == (__dif))		||		\
-	  ((__sk)->sk_bound_dev_if == (__sdif)))	&&		\
-	 net_eq(sock_net(__sk), (__net)))
-#endif /* 64-bit arch */
+static inline bool INET_MATCH(struct net *net, const struct sock *sk,
+			      const __addrpair cookie, const __portpair ports,
+			      int dif, int sdif)
+{
+	if (!net_eq(sock_net(sk), net) ||
+	    sk->sk_portpair != ports ||
+	    sk->sk_addrpair != cookie)
+	        return false;
+
+	/* READ_ONCE() paired with WRITE_ONCE() in sock_bindtoindex_locked() */
+	return inet_sk_bound_dev_eq(net, READ_ONCE(sk->sk_bound_dev_if), dif,
+				    sdif);
+}
 
 /* Sockets in TCP_CLOSE state are _always_ taken out of the hash, so we need
  * not check it for lookups anymore, thanks Alexey. -DaveM
@@ -335,6 +279,20 @@
 				       const __be32 daddr, const u16 hnum,
 				       const int dif, const int sdif);
 
+typedef u32 (inet_ehashfn_t)(const struct net *net,
+			      const __be32 laddr, const __u16 lport,
+			      const __be32 faddr, const __be16 fport);
+
+inet_ehashfn_t inet_ehashfn;
+
+INDIRECT_CALLABLE_DECLARE(inet_ehashfn_t udp_ehashfn);
+
+struct sock *inet_lookup_reuseport(struct net *net, struct sock *sk,
+				   struct sk_buff *skb, int doff,
+				   __be32 saddr, __be16 sport,
+				   __be32 daddr, unsigned short hnum,
+				   inet_ehashfn_t *ehashfn);
+
 static inline struct sock *
 	inet_lookup_established(struct net *net, struct inet_hashinfo *hashinfo,
 				const __be32 saddr, const __be16 sport,
@@ -404,10 +362,6 @@
 			     refcounted);
 }
 
-u32 inet6_ehashfn(const struct net *net,
-		  const struct in6_addr *laddr, const u16 lport,
-		  const struct in6_addr *faddr, const __be16 fport);
-
 static inline void sk_daddr_set(struct sock *sk, __be32 addr)
 {
 	sk->sk_daddr = addr; /* alias of inet_daddr */
@@ -425,7 +379,7 @@
 }
 
 int __inet_hash_connect(struct inet_timewait_death_row *death_row,
-			struct sock *sk, u32 port_offset,
+			struct sock *sk, u64 port_offset,
 			int (*check_established)(struct inet_timewait_death_row *,
 						 struct sock *, __u16,
 						 struct inet_timewait_sock **));
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/inet_sock.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/inet_sock.h
@@ -107,7 +107,8 @@
 
 static inline u32 inet_request_mark(const struct sock *sk, struct sk_buff *skb)
 {
-	if (!sk->sk_mark && sock_net(sk)->ipv4.sysctl_tcp_fwmark_accept)
+	if (!sk->sk_mark &&
+	    READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fwmark_accept))
 		return skb->mark;
 
 	return sk->sk_mark;
@@ -116,14 +117,15 @@
 static inline int inet_request_bound_dev_if(const struct sock *sk,
 					    struct sk_buff *skb)
 {
+	int bound_dev_if = READ_ONCE(sk->sk_bound_dev_if);
 #ifdef CONFIG_NET_L3_MASTER_DEV
 	struct net *net = sock_net(sk);
 
-	if (!sk->sk_bound_dev_if && net->ipv4.sysctl_tcp_l3mdev_accept)
+	if (!bound_dev_if && READ_ONCE(net->ipv4.sysctl_tcp_l3mdev_accept))
 		return l3mdev_master_ifindex_by_index(net, skb->skb_iif);
 #endif
 
-	return sk->sk_bound_dev_if;
+	return bound_dev_if;
 }
 
 static inline int inet_sk_bound_l3mdev(const struct sock *sk)
@@ -131,7 +133,7 @@
 #ifdef CONFIG_NET_L3_MASTER_DEV
 	struct net *net = sock_net(sk);
 
-	if (!net->ipv4.sysctl_tcp_l3mdev_accept)
+	if (!READ_ONCE(net->ipv4.sysctl_tcp_l3mdev_accept))
 		return l3mdev_master_ifindex_by_index(net,
 						      sk->sk_bound_dev_if);
 #endif
@@ -147,6 +149,17 @@
 	return bound_dev_if == dif || bound_dev_if == sdif;
 }
 
+static inline bool inet_sk_bound_dev_eq(struct net *net, int bound_dev_if,
+					int dif, int sdif)
+{
+#if IS_ENABLED(CONFIG_NET_L3_MASTER_DEV)
+	return inet_bound_dev_eq(!!READ_ONCE(net->ipv4.sysctl_tcp_l3mdev_accept),
+				 bound_dev_if, dif, sdif);
+#else
+	return inet_bound_dev_eq(true, bound_dev_if, dif, sdif);
+#endif
+}
+
 struct inet_cork {
 	unsigned int		flags;
 	__be32			addr;
@@ -207,11 +220,10 @@
 	__be32			inet_saddr;
 	__s16			uc_ttl;
 	__u16			cmsg_flags;
+	struct ip_options_rcu __rcu	*inet_opt;
 	__be16			inet_sport;
 	__u16			inet_id;
 
-	struct ip_options_rcu __rcu	*inet_opt;
-	int			rx_dst_ifindex;
 	__u8			tos;
 	__u8			min_ttl;
 	__u8			mc_ttl;
@@ -253,6 +265,11 @@
 #define IP_CMSG_CHECKSUM	BIT(7)
 #define IP_CMSG_RECVFRAGSIZE	BIT(8)
 
+static inline bool sk_is_inet(struct sock *sk)
+{
+	return sk->sk_family == AF_INET || sk->sk_family == AF_INET6;
+}
+
 /**
  * sk_to_full_sk - Access to a full socket
  * @sk: pointer to a socket
@@ -369,7 +386,7 @@
 static inline bool inet_can_nonlocal_bind(struct net *net,
 					  struct inet_sock *inet)
 {
-	return net->ipv4.sysctl_ip_nonlocal_bind ||
+	return READ_ONCE(net->ipv4.sysctl_ip_nonlocal_bind) ||
 		inet->freebind || inet->transparent;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ip.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ip.h
@@ -55,6 +55,8 @@
 #define IPSKB_DOREDIRECT	BIT(5)
 #define IPSKB_FRAG_PMTU		BIT(6)
 #define IPSKB_L3SLAVE		BIT(7)
+#define IPSKB_NOPOLICY		BIT(8)
+#define IPSKB_MULTIPATH		BIT(9)
 
 	u16			frag_max_size;
 };
@@ -74,6 +76,7 @@
 	__be32			addr;
 	int			oif;
 	struct ip_options_rcu	*opt;
+	__u8			protocol;
 	__u8			ttl;
 	__s16			tos;
 	char			priority;
@@ -94,6 +97,7 @@
 	ipcm->sockc.tsflags = inet->sk.sk_tsflags;
 	ipcm->oif = inet->sk.sk_bound_dev_if;
 	ipcm->addr = inet->inet_saddr;
+	ipcm->protocol = inet->inet_num;
 }
 
 #define IPCB(skb) ((struct inet_skb_parm*)((skb)->cb))
@@ -351,7 +355,7 @@
 
 static inline bool inet_port_requires_bind_service(struct net *net, unsigned short port)
 {
-	return port < net->ipv4.sysctl_ip_prot_sock;
+	return port < READ_ONCE(net->ipv4.sysctl_ip_prot_sock);
 }
 
 #else
@@ -378,7 +382,7 @@
 void ip_static_sysctl_init(void);
 
 #define IP4_REPLY_MARK(net, mark) \
-	((net)->ipv4.sysctl_fwmark_reflect ? (mark) : 0)
+	(READ_ONCE((net)->ipv4.sysctl_fwmark_reflect) ? (mark) : 0)
 
 static inline bool ip_is_fragment(const struct iphdr *iph)
 {
@@ -440,7 +444,7 @@
 	struct net *net = dev_net(dst->dev);
 	unsigned int mtu;
 
-	if (net->ipv4.sysctl_ip_fwd_use_pmtu ||
+	if (READ_ONCE(net->ipv4.sysctl_ip_fwd_use_pmtu) ||
 	    ip_mtu_locked(dst) ||
 	    !forwarding) {
 		mtu = rt->rt_pmtu;
@@ -520,19 +524,18 @@
 {
 	struct iphdr *iph = ip_hdr(skb);
 
+	/* We had many attacks based on IPID, use the private
+	 * generator as much as we can.
+	 */
+	if (sk && inet_sk(sk)->inet_daddr) {
+		iph->id = htons(inet_sk(sk)->inet_id);
+		inet_sk(sk)->inet_id += segs;
+		return;
+	}
 	if ((iph->frag_off & htons(IP_DF)) && !skb->ignore_df) {
-		/* This is only to work around buggy Windows95/2000
-		 * VJ compression implementations.  If the ID field
-		 * does not change, they drop every other packet in
-		 * a TCP stream using header compression.
-		 */
-		if (sk && inet_sk(sk)->inet_daddr) {
-			iph->id = htons(inet_sk(sk)->inet_id);
-			inet_sk(sk)->inet_id += segs;
-		} else {
-			iph->id = 0;
-		}
+		iph->id = 0;
 	} else {
+		/* Unfortunately we need the big hammer to get a suitable IPID */
 		__ip_select_ident(net, iph, segs);
 	}
 }
@@ -559,7 +562,7 @@
 	BUILD_BUG_ON(offsetof(typeof(flow->addrs), v4addrs.dst) !=
 		     offsetof(typeof(flow->addrs), v4addrs.src) +
 			      sizeof(flow->addrs.v4addrs.src));
-	memcpy(&flow->addrs.v4addrs, &iph->saddr, sizeof(flow->addrs.v4addrs));
+	memcpy(&flow->addrs.v4addrs, &iph->addrs, sizeof(flow->addrs.v4addrs));
 	flow->control.addr_type = FLOW_DISSECTOR_KEY_IPV4_ADDRS;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ip6_fib.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ip6_fib.h
@@ -189,14 +189,16 @@
 	u32				fib6_metric;
 	u8				fib6_protocol;
 	u8				fib6_type;
+
+	u8				offload;
+	u8				trap;
+	u8				offload_failed;
+
 	u8				should_flush:1,
 					dst_nocount:1,
 					dst_nopolicy:1,
 					fib6_destroying:1,
-					offload:1,
-					trap:1,
-					offload_failed:1,
-					unused:1;
+					unused:4;
 
 	struct rcu_head			rcu;
 	struct nexthop			*nh;
@@ -281,7 +283,7 @@
 	fn = rcu_dereference(f6i->fib6_node);
 
 	if (fn) {
-		*cookie = fn->fn_sernum;
+		*cookie = READ_ONCE(fn->fn_sernum);
 		/* pairs with smp_wmb() in __fib6_update_sernum_upto_root() */
 		smp_rmb();
 		status = true;
@@ -485,6 +487,7 @@
 		 struct fib6_config *cfg, gfp_t gfp_flags,
 		 struct netlink_ext_ack *extack);
 void fib6_nh_release(struct fib6_nh *fib6_nh);
+void fib6_nh_release_dsts(struct fib6_nh *fib6_nh);
 
 int call_fib6_entry_notifiers(struct net *net,
 			      enum fib_event_type event_type,
@@ -607,7 +610,10 @@
 	if (!net->ipv6.fib6_rules_require_fldissect)
 		return false;
 
-	skb_flow_dissect_flow_keys(skb, flkeys, flag);
+	memset(flkeys, 0, sizeof(*flkeys));
+	__skb_flow_dissect(net, skb, &flow_keys_dissector,
+			   flkeys, NULL, 0, 0, 0, flag);
+
 	fl6->fl6_sport = flkeys->ports.src;
 	fl6->fl6_dport = flkeys->ports.dst;
 	fl6->flowi6_proto = flkeys->basic.ip_proto;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ip6_tunnel.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ip6_tunnel.h
@@ -57,7 +57,7 @@
 
 	/* These fields used only by GRE */
 	__u32 i_seqno;	/* The last seen seqno	*/
-	__u32 o_seqno;	/* The last output seqno */
+	atomic_t o_seqno;	/* The last output seqno */
 	int hlen;       /* tun_hlen + encap_hlen */
 	int tun_hlen;	/* Precalculated header length */
 	int encap_hlen; /* Encap header length (FOU,GUE) */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ip_fib.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ip_fib.h
@@ -151,6 +151,7 @@
 	int			fib_nhs;
 	bool			fib_nh_is_v6;
 	bool			nh_updated;
+	bool			pfsrc_removed;
 	struct nexthop		*nh;
 	struct rcu_head		rcu;
 	struct fib_nh		fib_nh[];
@@ -415,7 +416,10 @@
 	if (!net->ipv4.fib_rules_require_fldissect)
 		return false;
 
-	skb_flow_dissect_flow_keys(skb, flkeys, flag);
+	memset(flkeys, 0, sizeof(*flkeys));
+	__skb_flow_dissect(net, skb, &flow_keys_dissector,
+			   flkeys, NULL, 0, 0, 0, flag);
+
 	fl4->fl4_sport = flkeys->ports.src;
 	fl4->fl4_dport = flkeys->ports.dst;
 	fl4->flowi4_proto = flkeys->basic.ip_proto;
@@ -438,7 +442,7 @@
 #ifdef CONFIG_IP_ROUTE_CLASSID
 static inline int fib_num_tclassid_users(struct net *net)
 {
-	return net->ipv4.fib_num_tclassid_users;
+	return atomic_read(&net->ipv4.fib_num_tclassid_users);
 }
 #else
 static inline int fib_num_tclassid_users(struct net *net)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ip_tunnels.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ip_tunnels.h
@@ -100,6 +100,28 @@
 };
 
 struct metadata_dst;
+/* A fan overlay /8 (250.0.0.0/8, for example) maps to exactly one /16
+ * underlay (10.88.0.0/16, for example).  Multiple local addresses within
+ * the /16 may be used, but a particular overlay may not span
+ * multiple underlay subnets.
+ *
+ * We store one underlay, indexed by the overlay's high order octet.
+ */
+#define FAN_OVERLAY_CNT		256
+
+struct ip_fan_map {
+	__be32			underlay;
+	__be32			overlay;
+	u16			underlay_prefix;
+	u16			overlay_prefix;
+	u32			overlay_mask;
+	struct list_head	list;
+	struct rcu_head		rcu;
+};
+
+struct ip_tunnel_fan {
+	struct list_head	fan_maps;
+};
 
 struct ip_tunnel {
 	struct ip_tunnel __rcu	*next;
@@ -113,7 +135,7 @@
 
 	/* These four fields used only by GRE */
 	u32		i_seqno;	/* The last seen seqno	*/
-	u32		o_seqno;	/* The last output seqno */
+	atomic_t	o_seqno;	/* The last output seqno */
 	int		tun_hlen;	/* Precalculated header length */
 
 	/* These four fields used only by ERSPAN */
@@ -137,6 +159,7 @@
 #endif
 	struct ip_tunnel_prl_entry __rcu *prl;	/* potential router list */
 	unsigned int		prl_count;	/* # of entries in PRL */
+	struct ip_tunnel_fan	fan;
 	unsigned int		ip_tnl_net_id;
 	struct gro_cells	gro_cells;
 	__u32			fwmark;
@@ -144,6 +167,11 @@
 	bool			ignore_df;
 };
 
+static inline int fan_has_map(const struct ip_tunnel_fan *fan)
+{
+	return !list_empty(&fan->fan_maps);
+}
+
 struct tnl_ptk_info {
 	__be16 flags;
 	__be16 proto;
@@ -240,11 +268,18 @@
 static inline void ip_tunnel_init_flow(struct flowi4 *fl4,
 				       int proto,
 				       __be32 daddr, __be32 saddr,
-				       __be32 key, __u8 tos, int oif,
+				       __be32 key, __u8 tos,
+				       struct net *net, int oif,
 				       __u32 mark, __u32 tun_inner_hash)
 {
 	memset(fl4, 0, sizeof(*fl4));
-	fl4->flowi4_oif = oif;
+
+	if (oif) {
+		fl4->flowi4_l3mdev = l3mdev_master_upper_ifindex_by_index(net, oif);
+		/* Legacy VRF/l3mdev use case */
+		fl4->flowi4_oif = fl4->flowi4_l3mdev ? 0 : oif;
+	}
+
 	fl4->daddr = daddr;
 	fl4->saddr = saddr;
 	fl4->flowi4_tos = tos;
@@ -332,6 +367,40 @@
 	return pskb_network_may_pull(skb, nhlen);
 }
 
+/* Variant of pskb_inet_may_pull().
+ */
+static inline bool skb_vlan_inet_prepare(struct sk_buff *skb,
+					 bool inner_proto_inherit)
+{
+	int nhlen = 0, maclen = inner_proto_inherit ? 0 : ETH_HLEN;
+	__be16 type = skb->protocol;
+
+	/* Essentially this is skb_protocol(skb, true)
+	 * And we get MAC len.
+	 */
+	if (eth_type_vlan(type))
+		type = __vlan_get_protocol(skb, type, &maclen);
+
+	switch (type) {
+#if IS_ENABLED(CONFIG_IPV6)
+	case htons(ETH_P_IPV6):
+		nhlen = sizeof(struct ipv6hdr);
+		break;
+#endif
+	case htons(ETH_P_IP):
+		nhlen = sizeof(struct iphdr);
+		break;
+	}
+	/* For ETH_P_IPV6/ETH_P_IP we make sure to pull
+	 * a base network header in skb->head.
+	 */
+	if (!pskb_may_pull(skb, maclen + nhlen))
+		return false;
+
+	skb_set_network_header(skb, maclen);
+	return true;
+}
+
 static inline int ip_encap_hlen(struct ip_tunnel_encap *e)
 {
 	const struct ip_tunnel_encap_ops *ops;
@@ -377,9 +446,11 @@
 static inline u8 ip_tunnel_get_dsfield(const struct iphdr *iph,
 				       const struct sk_buff *skb)
 {
-	if (skb->protocol == htons(ETH_P_IP))
+	__be16 payload_protocol = skb_protocol(skb, true);
+
+	if (payload_protocol == htons(ETH_P_IP))
 		return iph->tos;
-	else if (skb->protocol == htons(ETH_P_IPV6))
+	else if (payload_protocol == htons(ETH_P_IPV6))
 		return ipv6_get_dsfield((const struct ipv6hdr *)iph);
 	else
 		return 0;
@@ -388,9 +459,11 @@
 static inline u8 ip_tunnel_get_ttl(const struct iphdr *iph,
 				       const struct sk_buff *skb)
 {
-	if (skb->protocol == htons(ETH_P_IP))
+	__be16 payload_protocol = skb_protocol(skb, true);
+
+	if (payload_protocol == htons(ETH_P_IP))
 		return iph->ttl;
-	else if (skb->protocol == htons(ETH_P_IPV6))
+	else if (payload_protocol == htons(ETH_P_IPV6))
 		return ((const struct ipv6hdr *)iph)->hop_limit;
 	else
 		return 0;
@@ -450,15 +523,14 @@
 		tstats->tx_packets++;
 		u64_stats_update_end(&tstats->syncp);
 		put_cpu_ptr(tstats);
-	} else {
-		struct net_device_stats *err_stats = &dev->stats;
+		return;
+	}
 
-		if (pkt_len < 0) {
-			err_stats->tx_errors++;
-			err_stats->tx_aborted_errors++;
-		} else {
-			err_stats->tx_dropped++;
-		}
+	if (pkt_len < 0) {
+		DEV_STATS_INC(dev, tx_errors);
+		DEV_STATS_INC(dev, tx_aborted_errors);
+	} else {
+		DEV_STATS_INC(dev, tx_dropped);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ip_vs.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ip_vs.h
@@ -549,8 +549,10 @@
 	 */
 	struct ip_vs_app        *app;           /* bound ip_vs_app object */
 	void                    *app_data;      /* Application private data */
-	struct ip_vs_seq        in_seq;         /* incoming seq. struct */
-	struct ip_vs_seq        out_seq;        /* outgoing seq. struct */
+	struct_group(sync_conn_opt,
+		struct ip_vs_seq  in_seq;       /* incoming seq. struct */
+		struct ip_vs_seq  out_seq;      /* outgoing seq. struct */
+	);
 
 	const struct ip_vs_pe	*pe;
 	char			*pe_data;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ipv6.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ipv6.h
@@ -391,17 +391,20 @@
 		kfree_rcu(opt, rcu);
 }
 
+#if IS_ENABLED(CONFIG_IPV6)
 struct ip6_flowlabel *__fl6_sock_lookup(struct sock *sk, __be32 label);
 
 extern struct static_key_false_deferred ipv6_flowlabel_exclusive;
 static inline struct ip6_flowlabel *fl6_sock_lookup(struct sock *sk,
 						    __be32 label)
 {
-	if (static_branch_unlikely(&ipv6_flowlabel_exclusive.key))
+	if (static_branch_unlikely(&ipv6_flowlabel_exclusive.key) &&
+	    READ_ONCE(sock_net(sk)->ipv6.flowlabel_has_excl))
 		return __fl6_sock_lookup(sk, label) ? : ERR_PTR(-ENOENT);
 
 	return NULL;
 }
+#endif
 
 struct ipv6_txoptions *fl6_merge_options(struct ipv6_txoptions *opt_space,
 					 struct ip6_flowlabel *fl,
@@ -661,12 +664,8 @@
 /* more secured version of ipv6_addr_hash() */
 static inline u32 __ipv6_addr_jhash(const struct in6_addr *a, const u32 initval)
 {
-	u32 v = (__force u32)a->s6_addr32[0] ^ (__force u32)a->s6_addr32[1];
-
-	return jhash_3words(v,
-			    (__force u32)a->s6_addr32[2],
-			    (__force u32)a->s6_addr32[3],
-			    initval);
+	return jhash2((__force const u32 *)a->s6_addr32,
+		      ARRAY_SIZE(a->s6_addr32), initval);
 }
 
 static inline bool ipv6_addr_loopback(const struct in6_addr *a)
@@ -840,7 +839,7 @@
 	BUILD_BUG_ON(offsetof(typeof(flow->addrs), v6addrs.dst) !=
 		     offsetof(typeof(flow->addrs), v6addrs.src) +
 		     sizeof(flow->addrs.v6addrs.src));
-	memcpy(&flow->addrs.v6addrs, &iph->saddr, sizeof(flow->addrs.v6addrs));
+	memcpy(&flow->addrs.v6addrs, &iph->addrs, sizeof(flow->addrs.v6addrs));
 	flow->control.addr_type = FLOW_DISSECTOR_KEY_IPV6_ADDRS;
 }
 
@@ -1001,7 +1000,7 @@
 int ip6_append_data(struct sock *sk,
 		    int getfrag(void *from, char *to, int offset, int len,
 				int odd, struct sk_buff *skb),
-		    void *from, int length, int transhdrlen,
+		    void *from, size_t length, int transhdrlen,
 		    struct ipcm6_cookie *ipc6, struct flowi6 *fl6,
 		    struct rt6_info *rt, unsigned int flags);
 
@@ -1017,7 +1016,7 @@
 struct sk_buff *ip6_make_skb(struct sock *sk,
 			     int getfrag(void *from, char *to, int offset,
 					 int len, int odd, struct sk_buff *skb),
-			     void *from, int length, int transhdrlen,
+			     void *from, size_t length, int transhdrlen,
 			     struct ipcm6_cookie *ipc6, struct flowi6 *fl6,
 			     struct rt6_info *rt, unsigned int flags,
 			     struct inet_cork_full *cork);
@@ -1115,6 +1114,8 @@
 void ipv6_local_error(struct sock *sk, int err, struct flowi6 *fl6, u32 info);
 void ipv6_local_rxpmtu(struct sock *sk, struct flowi6 *fl6, u32 mtu);
 
+void inet6_cleanup_sock(struct sock *sk);
+void inet6_sock_destruct(struct sock *sk);
 int inet6_release(struct socket *sock);
 int inet6_bind(struct socket *sock, struct sockaddr *uaddr, int addr_len);
 int inet6_getname(struct socket *sock, struct sockaddr *uaddr,
@@ -1257,7 +1258,7 @@
 	return 0;
 }
 
-static inline int ip6_sock_set_addr_preferences(struct sock *sk, bool val)
+static inline int ip6_sock_set_addr_preferences(struct sock *sk, int val)
 {
 	int ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ipv6_frag.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ipv6_frag.h
@@ -67,7 +67,8 @@
 	struct sk_buff *head;
 
 	rcu_read_lock();
-	if (fq->q.fqdir->dead)
+	/* Paired with the WRITE_ONCE() in fqdir_pre_exit(). */
+	if (READ_ONCE(fq->q.fqdir->dead))
 		goto out_rcu_unlock;
 	spin_lock(&fq->q.lock);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ipv6_stubs.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ipv6_stubs.h
@@ -47,6 +47,7 @@
 			    struct fib6_config *cfg, gfp_t gfp_flags,
 			    struct netlink_ext_ack *extack);
 	void (*fib6_nh_release)(struct fib6_nh *fib6_nh);
+	void (*fib6_nh_release_dsts)(struct fib6_nh *fib6_nh);
 	void (*fib6_update_sernum)(struct net *net, struct fib6_info *rt);
 	int (*ip6_del_rt)(struct net *net, struct fib6_info *rt, bool skip_notify);
 	void (*fib6_rt_update)(struct net *net, struct fib6_info *rt,
@@ -80,6 +81,11 @@
 				     const struct in6_addr *daddr, __be16 dport,
 				     int dif, int sdif, struct udp_table *tbl,
 				     struct sk_buff *skb);
+	int (*ipv6_dev_get_saddr)(struct net *net,
+				  const struct net_device *dst_dev,
+				  const struct in6_addr *daddr,
+				  unsigned int prefs,
+				  struct in6_addr *saddr);
 };
 extern const struct ipv6_bpf_stub *ipv6_bpf_stub __read_mostly;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/kcm.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/kcm.h
@@ -70,6 +70,7 @@
 	struct work_struct tx_work;
 	struct list_head wait_psock_list;
 	struct sk_buff *seq_skb;
+	struct mutex tx_mutex;
 	u32 tx_stopped : 1;
 
 	/* Don't use bit fields here, these are set under different locks */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/l3mdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/l3mdev.h
@@ -198,10 +198,12 @@
 	if (netif_is_l3_slave(dev)) {
 		struct net_device *master;
 
+		rcu_read_lock();
 		master = netdev_master_upper_dev_get_rcu(dev);
 		if (master && master->l3mdev_ops->l3mdev_l3_out)
 			skb = master->l3mdev_ops->l3mdev_l3_out(master, sk,
 								skb, proto);
+		rcu_read_unlock();
 	}
 
 	return skb;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/lapb.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/lapb.h
@@ -4,7 +4,7 @@
 #include <linux/lapb.h>
 #include <linux/refcount.h>
 
-#define	LAPB_HEADER_LEN	20		/* LAPB over Ethernet + a bit more */
+#define	LAPB_HEADER_LEN MAX_HEADER		/* LAPB over Ethernet + a bit more */
 
 #define	LAPB_ACK_PENDING_CONDITION	0x01
 #define	LAPB_REJECT_CONDITION		0x02
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/llc.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/llc.h
@@ -72,7 +72,9 @@
 static inline
 struct hlist_head *llc_sk_dev_hash(struct llc_sap *sap, int ifindex)
 {
-	return &sap->sk_dev_hash[ifindex % LLC_SK_DEV_HASH_ENTRIES];
+	u32 bucket = hash_32(ifindex, LLC_SK_DEV_HASH_BITS);
+
+	return &sap->sk_dev_hash[bucket];
 }
 
 static inline
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/llc_pdu.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/llc_pdu.h
@@ -262,8 +262,7 @@
  */
 static inline void llc_pdu_decode_sa(struct sk_buff *skb, u8 *sa)
 {
-	if (skb->protocol == htons(ETH_P_802_2))
-		memcpy(sa, eth_hdr(skb)->h_source, ETH_ALEN);
+	memcpy(sa, eth_hdr(skb)->h_source, ETH_ALEN);
 }
 
 /**
@@ -275,8 +274,7 @@
  */
 static inline void llc_pdu_decode_da(struct sk_buff *skb, u8 *da)
 {
-	if (skb->protocol == htons(ETH_P_802_2))
-		memcpy(da, eth_hdr(skb)->h_dest, ETH_ALEN);
+	memcpy(da, eth_hdr(skb)->h_dest, ETH_ALEN);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/lwtunnel.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/lwtunnel.h
@@ -16,9 +16,12 @@
 #define LWTUNNEL_STATE_INPUT_REDIRECT	BIT(1)
 #define LWTUNNEL_STATE_XMIT_REDIRECT	BIT(2)
 
+/* LWTUNNEL_XMIT_CONTINUE should be distinguishable from dst_output return
+ * values (NET_XMIT_xxx and NETDEV_TX_xxx in linux/netdevice.h) for safety.
+ */
 enum {
 	LWTUNNEL_XMIT_DONE,
-	LWTUNNEL_XMIT_CONTINUE,
+	LWTUNNEL_XMIT_CONTINUE = 0x100,
 };
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/mac80211.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/mac80211.h
@@ -7,7 +7,7 @@
  * Copyright 2007-2010	Johannes Berg <johannes@sipsolutions.net>
  * Copyright 2013-2014  Intel Mobile Communications GmbH
  * Copyright (C) 2015 - 2017 Intel Deutschland GmbH
- * Copyright (C) 2018 - 2021 Intel Corporation
+ * Copyright (C) 2018 - 2022 Intel Corporation
  */
 
 #ifndef MAC80211_H
@@ -875,6 +875,17 @@
 	IEEE80211_TX_CTRL_DONT_REORDER		= BIT(8),
 };
 
+/**
+ * enum mac80211_tx_status_flags - flags to describe transmit status
+ *
+ * @IEEE80211_TX_STATUS_ACK_SIGNAL_VALID: ACK signal is valid
+ *
+ * These flags are used in tx_info->status.flags.
+ */
+enum mac80211_tx_status_flags {
+	IEEE80211_TX_STATUS_ACK_SIGNAL_VALID = BIT(0),
+};
+
 /*
  * This definition is used as a mask to clear all temporary flags, which are
  * set by the tx handlers for each transmission attempt by the mac80211 stack.
@@ -1038,7 +1049,7 @@
  * @status.antenna: (legacy, kept only for iwlegacy)
  * @status.tx_time: airtime consumed for transmission; note this is only
  *	used for WMM AC, not for airtime fairness
- * @status.is_valid_ack_signal: ACK signal is valid
+ * @status.flags: status flags, see &enum mac80211_tx_status_flags
  * @status.status_driver_data: driver use area
  * @ack: union part for pure ACK data
  * @ack.cookie: cookie for the ACK
@@ -1091,8 +1102,8 @@
 			u8 ampdu_len;
 			u8 antenna;
 			u16 tx_time;
-			bool is_valid_ack_signal;
-			void *status_driver_data[19 / sizeof(void *)];
+			u8 flags;
+			void *status_driver_data[18 / sizeof(void *)];
 		} status;
 		struct {
 			struct ieee80211_tx_rate driver_rates[
@@ -6010,6 +6021,16 @@
 void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
 
 /**
+ * ieee80211_hw_restart_disconnect - disconnect from AP after
+ * hardware restart
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * Instructs mac80211 to disconnect from the AP after
+ * hardware restart.
+ */
+void ieee80211_hw_restart_disconnect(struct ieee80211_vif *vif);
+
+/**
  * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
  *	rssi threshold triggered
  *
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/macsec.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/macsec.h
@@ -240,6 +240,7 @@
 	struct macsec_secy *secy;
 	struct macsec_rx_sc *rx_sc;
 	struct {
+		bool update_pn;
 		unsigned char assoc_num;
 		u8 key[MACSEC_MAX_KEY_LEN];
 		union {
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/mctp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/mctp.h
@@ -226,7 +226,7 @@
 int mctp_routes_init(void);
 void mctp_routes_exit(void);
 
-void mctp_device_init(void);
+int mctp_device_init(void);
 void mctp_device_exit(void);
 
 #endif /* __NET_MCTP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/mctpdevice.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/mctpdevice.h
@@ -17,6 +17,8 @@
 struct mctp_dev {
 	struct net_device	*dev;
 
+	refcount_t		refs;
+
 	unsigned int		net;
 
 	/* Only modified under RTNL. Reads have addrs_lock held */
@@ -32,4 +34,7 @@
 struct mctp_dev *mctp_dev_get_rtnl(const struct net_device *dev);
 struct mctp_dev *__mctp_dev_get(const struct net_device *dev);
 
+void mctp_dev_hold(struct mctp_dev *mdev);
+void mctp_dev_put(struct mctp_dev *mdev);
+
 #endif /* __NET_MCTPDEVICE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/mptcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/mptcp.h
@@ -93,8 +93,6 @@
 };
 
 #ifdef CONFIG_MPTCP
-extern struct request_sock_ops mptcp_subflow_request_sock_ops;
-
 void mptcp_init(void);
 
 static inline bool sk_is_mptcp(const struct sock *sk)
@@ -182,6 +180,9 @@
 int mptcp_subflow_init_cookie_req(struct request_sock *req,
 				  const struct sock *sk_listener,
 				  struct sk_buff *skb);
+struct request_sock *mptcp_subflow_reqsk_alloc(const struct request_sock_ops *ops,
+					       struct sock *sk_listener,
+					       bool attach_listener);
 
 __be32 mptcp_get_reset_option(const struct sk_buff *skb);
 
@@ -274,6 +275,13 @@
 	return 0; /* TCP fallback */
 }
 
+static inline struct request_sock *mptcp_subflow_reqsk_alloc(const struct request_sock_ops *ops,
+							     struct sock *sk_listener,
+							     bool attach_listener)
+{
+	return NULL;
+}
+
 static inline __be32 mptcp_reset_option(const struct sk_buff *skb)  { return htonl(0u); }
 #endif /* CONFIG_MPTCP */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/mrp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/mrp.h
@@ -120,6 +120,7 @@
 	struct sk_buff		*pdu;
 	struct rb_root		mad;
 	struct rcu_head		rcu;
+	bool			active;
 };
 
 struct mrp_port {
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/ndisc.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/ndisc.h
@@ -487,9 +487,9 @@
 void igmp6_cleanup(void);
 void igmp6_late_cleanup(void);
 
-int igmp6_event_query(struct sk_buff *skb);
+void igmp6_event_query(struct sk_buff *skb);
 
-int igmp6_event_report(struct sk_buff *skb);
+void igmp6_event_report(struct sk_buff *skb);
 
 
 #ifdef CONFIG_SYSCTL
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/neighbour.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/neighbour.h
@@ -174,7 +174,7 @@
 	struct net_device	*dev;
 	u8			flags;
 	u8			protocol;
-	u8			key[];
+	u32			key[];
 };
 
 /*
@@ -253,17 +253,13 @@
 #define NEIGH_UPDATE_F_OVERRIDE			0x00000001
 #define NEIGH_UPDATE_F_WEAK_OVERRIDE		0x00000002
 #define NEIGH_UPDATE_F_OVERRIDE_ISROUTER	0x00000004
+#define NEIGH_UPDATE_F_USE			0x10000000
 #define NEIGH_UPDATE_F_EXT_LEARNED		0x20000000
 #define NEIGH_UPDATE_F_ISROUTER			0x40000000
 #define NEIGH_UPDATE_F_ADMIN			0x80000000
 
 extern const struct nla_policy nda_policy[];
 
-static inline bool neigh_key_eq16(const struct neighbour *n, const void *pkey)
-{
-	return *(const u16 *)n->primary_key == *(const u16 *)pkey;
-}
-
 static inline bool neigh_key_eq32(const struct neighbour *n, const void *pkey)
 {
 	return *(const u32 *)n->primary_key == *(const u32 *)pkey;
@@ -313,8 +309,6 @@
 int neigh_table_clear(int index, struct neigh_table *tbl);
 struct neighbour *neigh_lookup(struct neigh_table *tbl, const void *pkey,
 			       struct net_device *dev);
-struct neighbour *neigh_lookup_nodev(struct neigh_table *tbl, struct net *net,
-				     const void *pkey);
 struct neighbour *__neigh_create(struct neigh_table *tbl, const void *pkey,
 				 struct net_device *dev, bool want_ref);
 static inline struct neighbour *neigh_create(struct neigh_table *tbl,
@@ -504,10 +498,15 @@
 {
 	const struct hh_cache *hh = &n->hh;
 
-	if ((n->nud_state & NUD_CONNECTED) && hh->hh_len && !skip_cache)
+	/* n->nud_state and hh->hh_len could be changed under us.
+	 * neigh_hh_output() is taking care of the race later.
+	 */
+	if (!skip_cache &&
+	    (READ_ONCE(n->nud_state) & NUD_CONNECTED) &&
+	    READ_ONCE(hh->hh_len))
 		return neigh_hh_output(hh, skb);
-	else
-		return n->output(n, skb);
+
+	return n->output(n, skb);
 }
 
 static inline struct neighbour *
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/net_namespace.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/net_namespace.h
@@ -26,6 +26,9 @@
 #if defined(CONFIG_NF_CONNTRACK) || defined(CONFIG_NF_CONNTRACK_MODULE)
 #include <net/netns/conntrack.h>
 #endif
+#if IS_ENABLED(CONFIG_NF_FLOW_TABLE)
+#include <net/netns/flow_table.h>
+#endif
 #include <net/netns/nftables.h>
 #include <net/netns/xfrm.h>
 #include <net/netns/mpls.h>
@@ -77,6 +80,7 @@
 						 * or to unregister pernet ops
 						 * (pernet_ops_rwsem write locked).
 						 */
+	struct llist_node	defer_free_list;
 	struct llist_node	cleanup_list;	/* namespaces on death row */
 
 #ifdef CONFIG_KEYS
@@ -138,6 +142,9 @@
 #if defined(CONFIG_NF_TABLES) || defined(CONFIG_NF_TABLES_MODULE)
 	struct netns_nftables	nft;
 #endif
+#if IS_ENABLED(CONFIG_NF_FLOW_TABLE)
+	struct netns_ft ft;
+#endif
 #endif
 #ifdef CONFIG_WEXT_CORE
 	struct sk_buff_head	wext_nlevents;
@@ -310,21 +317,30 @@
 
 typedef struct {
 #ifdef CONFIG_NET_NS
-	struct net *net;
+	struct net __rcu *net;
 #endif
 } possible_net_t;
 
 static inline void write_pnet(possible_net_t *pnet, struct net *net)
 {
 #ifdef CONFIG_NET_NS
-	pnet->net = net;
+	rcu_assign_pointer(pnet->net, net);
 #endif
 }
 
 static inline struct net *read_pnet(const possible_net_t *pnet)
 {
 #ifdef CONFIG_NET_NS
-	return pnet->net;
+	return rcu_dereference_protected(pnet->net, true);
+#else
+	return &init_net;
+#endif
+}
+
+static inline struct net *read_pnet_rcu(const possible_net_t *pnet)
+{
+#ifdef CONFIG_NET_NS
+	return rcu_dereference(pnet->net);
 #else
 	return &init_net;
 #endif
@@ -383,6 +399,9 @@
 	void (*pre_exit)(struct net *net);
 	void (*exit)(struct net *net);
 	void (*exit_batch)(struct list_head *net_exit_list);
+	/* Following method is called with RTNL held. */
+	void (*exit_batch_rtnl)(struct list_head *net_exit_list,
+				struct list_head *dev_kill_list);
 	unsigned int *id;
 	size_t size;
 };
@@ -479,4 +498,10 @@
 	atomic_inc(&net->fnhe_genid);
 }
 
+#ifdef CONFIG_NET
+void net_ns_init(void);
+#else
+static inline void net_ns_init(void) {}
+#endif
+
 #endif /* __NET_NET_NAMESPACE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_conntrack.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_conntrack.h
@@ -76,6 +76,8 @@
 	 * Hint, SKB address this struct and refcnt via skb->_nfct and
 	 * helpers nf_conntrack_get() and nf_conntrack_put().
 	 * Helper nf_ct_put() equals nf_conntrack_put() by dec refcnt,
+	 * except that the latter uses internal indirection and does not
+	 * result in a conntrack module dependency.
 	 * beware nf_ct_get() is different and don't inc refcnt.
 	 */
 	struct nf_conntrack ct_general;
@@ -122,6 +124,12 @@
 };
 
 static inline struct nf_conn *
+nf_ct_to_nf_conn(const struct nf_conntrack *nfct)
+{
+	return container_of(nfct, struct nf_conn, ct_general);
+}
+
+static inline struct nf_conn *
 nf_ct_tuplehash_to_ctrack(const struct nf_conntrack_tuple_hash *hash)
 {
 	return container_of(hash, struct nf_conn,
@@ -169,11 +177,15 @@
 	return (struct nf_conn *)(nfct & NFCT_PTRMASK);
 }
 
+void nf_ct_destroy(struct nf_conntrack *nfct);
+
+void nf_conntrack_tcp_set_closing(struct nf_conn *ct);
+
 /* decrement reference count on a conntrack */
 static inline void nf_ct_put(struct nf_conn *ct)
 {
-	WARN_ON(!ct);
-	nf_conntrack_put(&ct->ct_general);
+	if (ct && refcount_dec_and_test(&ct->ct_general.use))
+		nf_ct_destroy(&ct->ct_general);
 }
 
 /* Protocol module loading */
@@ -276,14 +288,14 @@
 /* jiffies until ct expires, 0 if already expired */
 static inline unsigned long nf_ct_expires(const struct nf_conn *ct)
 {
-	s32 timeout = ct->timeout - nfct_time_stamp;
+	s32 timeout = READ_ONCE(ct->timeout) - nfct_time_stamp;
 
 	return timeout > 0 ? timeout : 0;
 }
 
 static inline bool nf_ct_is_expired(const struct nf_conn *ct)
 {
-	return (__s32)(ct->timeout - nfct_time_stamp) <= 0;
+	return (__s32)(READ_ONCE(ct->timeout) - nfct_time_stamp) <= 0;
 }
 
 /* use after obtaining a reference count */
@@ -302,7 +314,7 @@
 static inline void nf_ct_offload_timeout(struct nf_conn *ct)
 {
 	if (nf_ct_expires(ct) < NF_CT_DAY / 2)
-		ct->timeout = nfct_time_stamp + NF_CT_DAY;
+		WRITE_ONCE(ct->timeout, nfct_time_stamp + NF_CT_DAY);
 }
 
 struct kernel_param;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_conntrack_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_conntrack_core.h
@@ -58,8 +58,13 @@
 	int ret = NF_ACCEPT;
 
 	if (ct) {
-		if (!nf_ct_is_confirmed(ct))
+		if (!nf_ct_is_confirmed(ct)) {
 			ret = __nf_conntrack_confirm(skb);
+
+			if (ret == NF_ACCEPT)
+				ct = (struct nf_conn *)skb_nfct(skb);
+		}
+
 		if (likely(ret == NF_ACCEPT))
 			nf_ct_deliver_cached_events(ct);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_conntrack_expect.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_conntrack_expect.h
@@ -100,7 +100,7 @@
 struct nf_conntrack_expect *
 nf_ct_find_expectation(struct net *net,
 		       const struct nf_conntrack_zone *zone,
-		       const struct nf_conntrack_tuple *tuple);
+		       const struct nf_conntrack_tuple *tuple, bool unlink);
 
 void nf_ct_unlink_expect_report(struct nf_conntrack_expect *exp,
 				u32 portid, int report);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_conntrack_helper.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_conntrack_helper.h
@@ -177,4 +177,5 @@
 int nf_nat_helper_try_module_get(const char *name, u16 l3num,
 				 u8 protonum);
 void nf_nat_helper_put(struct nf_conntrack_helper *helper);
+void nf_ct_set_auto_assign_helper_warned(struct net *net);
 #endif /*_NF_CONNTRACK_HELPER_H*/
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_flow_table.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_flow_table.h
@@ -10,6 +10,8 @@
 #include <linux/netfilter/nf_conntrack_tuple_common.h>
 #include <net/flow_offload.h>
 #include <net/dst.h>
+#include <linux/if_pppox.h>
+#include <linux/ppp_defs.h>
 
 struct nf_flowtable;
 struct nf_flow_rule;
@@ -255,8 +257,8 @@
 	up_write(&flow_table->flow_block_lock);
 }
 
-int flow_offload_route_init(struct flow_offload *flow,
-			    const struct nf_flow_route *route);
+void flow_offload_route_init(struct flow_offload *flow,
+			     struct nf_flow_route *route);
 
 int flow_offload_add(struct nf_flowtable *flow_table, struct flow_offload *flow);
 void flow_offload_refresh(struct nf_flowtable *flow_table,
@@ -264,6 +266,7 @@
 
 struct flow_offload_tuple_rhash *flow_offload_lookup(struct nf_flowtable *flow_table,
 						     struct flow_offload_tuple *tuple);
+void nf_flow_table_gc_run(struct nf_flowtable *flow_table);
 void nf_flow_table_gc_cleanup(struct nf_flowtable *flowtable,
 			      struct net_device *dev);
 void nf_flow_table_cleanup(struct net_device *dev);
@@ -300,6 +303,8 @@
 			   struct flow_offload *flow);
 
 void nf_flow_table_offload_flush(struct nf_flowtable *flowtable);
+void nf_flow_table_offload_flush_cleanup(struct nf_flowtable *flowtable);
+
 int nf_flow_table_offload_setup(struct nf_flowtable *flowtable,
 				struct net_device *dev,
 				enum flow_block_command cmd);
@@ -313,4 +318,51 @@
 int nf_flow_table_offload_init(void);
 void nf_flow_table_offload_exit(void);
 
+static inline __be16 __nf_flow_pppoe_proto(const struct sk_buff *skb)
+{
+	__be16 proto;
+
+	proto = *((__be16 *)(skb_mac_header(skb) + ETH_HLEN +
+			     sizeof(struct pppoe_hdr)));
+	switch (proto) {
+	case htons(PPP_IP):
+		return htons(ETH_P_IP);
+	case htons(PPP_IPV6):
+		return htons(ETH_P_IPV6);
+	}
+
+	return 0;
+}
+
+static inline bool nf_flow_pppoe_proto(struct sk_buff *skb, __be16 *inner_proto)
+{
+	if (!pskb_may_pull(skb, PPPOE_SES_HLEN))
+		return false;
+
+	*inner_proto = __nf_flow_pppoe_proto(skb);
+
+	return true;
+}
+
+#define NF_FLOW_TABLE_STAT_INC(net, count) __this_cpu_inc((net)->ft.stat->count)
+#define NF_FLOW_TABLE_STAT_DEC(net, count) __this_cpu_dec((net)->ft.stat->count)
+#define NF_FLOW_TABLE_STAT_INC_ATOMIC(net, count)	\
+	this_cpu_inc((net)->ft.stat->count)
+#define NF_FLOW_TABLE_STAT_DEC_ATOMIC(net, count)	\
+	this_cpu_dec((net)->ft.stat->count)
+
+#ifdef CONFIG_NF_FLOW_TABLE_PROCFS
+int nf_flow_table_init_proc(struct net *net);
+void nf_flow_table_fini_proc(struct net *net);
+#else
+static inline int nf_flow_table_init_proc(struct net *net)
+{
+	return 0;
+}
+
+static inline void nf_flow_table_fini_proc(struct net *net)
+{
+}
+#endif /* CONFIG_NF_FLOW_TABLE_PROCFS */
+
 #endif /* _NF_FLOW_TABLE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_nat_redirect.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_nat_redirect.h
@@ -6,8 +6,7 @@
 #include <uapi/linux/netfilter/nf_nat.h>
 
 unsigned int
-nf_nat_redirect_ipv4(struct sk_buff *skb,
-		     const struct nf_nat_ipv4_multi_range_compat *mr,
+nf_nat_redirect_ipv4(struct sk_buff *skb, const struct nf_nat_range2 *range,
 		     unsigned int hooknum);
 unsigned int
 nf_nat_redirect_ipv6(struct sk_buff *skb, const struct nf_nat_range2 *range,
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_queue.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_queue.h
@@ -37,7 +37,7 @@
 void nf_unregister_queue_handler(void);
 void nf_reinject(struct nf_queue_entry *entry, unsigned int verdict);
 
-void nf_queue_entry_get_refs(struct nf_queue_entry *entry);
+bool nf_queue_entry_get_refs(struct nf_queue_entry *entry);
 void nf_queue_entry_free(struct nf_queue_entry *entry);
 
 static inline void init_hashrandom(u32 *jhash_initval)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_tables.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_tables.h
@@ -21,13 +21,19 @@
 
 #define NFT_JUMP_STACK_SIZE	16
 
+enum {
+	NFT_PKTINFO_L4PROTO	= (1 << 0),
+	NFT_PKTINFO_INNER	= (1 << 1),
+};
+
 struct nft_pktinfo {
 	struct sk_buff			*skb;
 	const struct nf_hook_state	*state;
-	bool				tprot_set;
+	u8				flags;
 	u8				tprot;
 	u16				fragoff;
 	unsigned int			thoff;
+	unsigned int			inneroff;
 };
 
 static inline struct sock *nft_sk(const struct nft_pktinfo *pkt)
@@ -75,7 +81,7 @@
 
 static inline void nft_set_pktinfo_unspec(struct nft_pktinfo *pkt)
 {
-	pkt->tprot_set = false;
+	pkt->flags = 0;
 	pkt->tprot = 0;
 	pkt->thoff = 0;
 	pkt->fragoff = 0;
@@ -138,14 +144,29 @@
 	*(u16 *)dreg = val;
 }
 
+static inline void nft_reg_store_be16(u32 *dreg, __be16 val)
+{
+	nft_reg_store16(dreg, (__force __u16)val);
+}
+
 static inline u16 nft_reg_load16(const u32 *sreg)
 {
 	return *(u16 *)sreg;
 }
 
-static inline void nft_reg_store64(u32 *dreg, u64 val)
+static inline __be16 nft_reg_load_be16(const u32 *sreg)
 {
-	put_unaligned(val, (u64 *)dreg);
+	return (__force __be16)nft_reg_load16(sreg);
+}
+
+static inline __be32 nft_reg_load_be32(const u32 *sreg)
+{
+	return *(__force __be32 *)sreg;
+}
+
+static inline void nft_reg_store64(u64 *dreg, u64 val)
+{
+	put_unaligned(val, dreg);
 }
 
 static inline u64 nft_reg_load64(const u32 *sreg)
@@ -187,13 +208,18 @@
 	bool				report;
 };
 
+enum nft_data_desc_flags {
+	NFT_DATA_DESC_SETELEM	= (1 << 0),
+};
+
 struct nft_data_desc {
 	enum nft_data_types		type;
+	unsigned int			size;
 	unsigned int			len;
+	unsigned int			flags;
 };
 
-int nft_data_init(const struct nft_ctx *ctx,
-		  struct nft_data *data, unsigned int size,
+int nft_data_init(const struct nft_ctx *ctx, struct nft_data *data,
 		  struct nft_data_desc *desc, const struct nlattr *nla);
 void nft_data_hold(const struct nft_data *data, enum nft_data_types type);
 void nft_data_release(const struct nft_data *data, enum nft_data_types type);
@@ -257,9 +283,22 @@
 	void			*priv;
 };
 
+/**
+ * enum nft_iter_type - nftables set iterator type
+ *
+ * @NFT_ITER_READ: read-only iteration over set elements
+ * @NFT_ITER_UPDATE: iteration under mutex to update set element state
+ */
+enum nft_iter_type {
+	NFT_ITER_UNSPEC,
+	NFT_ITER_READ,
+	NFT_ITER_UPDATE,
+};
+
 struct nft_set;
 struct nft_set_iter {
 	u8		genmask;
+	enum nft_iter_type type:8;
 	unsigned int	count;
 	unsigned int	skip;
 	int		err;
@@ -272,17 +311,29 @@
 /**
  *	struct nft_set_desc - description of set elements
  *
+ *	@ktype: key type
  *	@klen: key length
+ *	@dtype: data type
  *	@dlen: data length
+ *	@objtype: object type
+ *	@flags: flags
  *	@size: number of set elements
+ *	@policy: set policy
+ *	@gc_int: garbage collector interval
  *	@field_len: length of each field in concatenation, bytes
  *	@field_count: number of concatenated fields in element
  *	@expr: set must support for expressions
  */
 struct nft_set_desc {
+	u32			ktype;
 	unsigned int		klen;
+	u32			dtype;
 	unsigned int		dlen;
+	u32			objtype;
 	unsigned int		size;
+	u32			policy;
+	u32			gc_int;
+	u64			timeout;
 	u8			field_len[NFT_REG32_COUNT];
 	u8			field_count;
 	bool			expr;
@@ -336,7 +387,7 @@
 	return (void *)expr->data;
 }
 
-int nft_expr_clone(struct nft_expr *dst, struct nft_expr *src);
+int nft_expr_clone(struct nft_expr *dst, struct nft_expr *src, gfp_t gfp);
 void nft_expr_destroy(const struct nft_ctx *ctx, struct nft_expr *expr);
 int nft_expr_dump(struct sk_buff *skb, unsigned int attr,
 		  const struct nft_expr *expr);
@@ -404,7 +455,8 @@
 					       const struct nft_set *set,
 					       const struct nft_set_elem *elem,
 					       unsigned int flags);
-
+	void				(*commit)(const struct nft_set *set);
+	void				(*abort)(const struct nft_set *set);
 	u64				(*privsize)(const struct nlattr * const nla[],
 						    const struct nft_set_desc *desc);
 	bool				(*estimate)(const struct nft_set_desc *desc,
@@ -413,7 +465,8 @@
 	int				(*init)(const struct nft_set *set,
 						const struct nft_set_desc *desc,
 						const struct nlattr * const nla[]);
-	void				(*destroy)(const struct nft_set *set);
+	void				(*destroy)(const struct nft_ctx *ctx,
+						   const struct nft_set *set);
 	void				(*gc_init)(const struct nft_set *set);
 
 	unsigned int			elemsize;
@@ -452,6 +505,7 @@
  *
  *	@list: table set list node
  *	@bindings: list of set bindings
+ *	@refs: internal refcounting for async set destruction
  *	@table: table this set belongs to
  *	@net: netnamespace this set belongs to
  * 	@name: name of the set
@@ -473,6 +527,7 @@
  *	@expr: stateful expression
  * 	@ops: set ops
  * 	@flags: set flags
+ *	@dead: set will be freed, never cleared
  *	@genmask: generation mask
  * 	@klen: key length
  * 	@dlen: data length
@@ -481,6 +536,7 @@
 struct nft_set {
 	struct list_head		list;
 	struct list_head		bindings;
+	refcount_t			refs;
 	struct nft_table		*table;
 	possible_net_t			net;
 	char				*name;
@@ -499,9 +555,11 @@
 	u16				policy;
 	u16				udlen;
 	unsigned char			*udata;
+	struct list_head		pending_update;
 	/* runtime data below here */
 	const struct nft_set_ops	*ops ____cacheline_aligned;
-	u16				flags:14,
+	u16				flags:13,
+					dead:1,
 					genmask:2;
 	u8				klen;
 	u8				dlen;
@@ -522,6 +580,16 @@
 	return (void *)set->data;
 }
 
+static inline enum nft_data_types nft_set_datatype(const struct nft_set *set)
+{
+	return set->dtype == NFT_DATA_VERDICT ? NFT_DATA_VERDICT : NFT_DATA_VALUE;
+}
+
+static inline bool nft_set_gc_is_pending(const struct nft_set *s)
+{
+	return refcount_read(&s->refs) != 1;
+}
+
 static inline struct nft_set *nft_set_container_of(const void *priv)
 {
 	return (void *)priv - offsetof(struct nft_set, data);
@@ -535,11 +603,12 @@
 
 struct nft_set_ext *nft_set_catchall_lookup(const struct net *net,
 					    const struct nft_set *set);
-void *nft_set_catchall_gc(const struct nft_set *set);
 
 static inline unsigned long nft_set_gc_interval(const struct nft_set *set)
 {
-	return set->gc_int ? msecs_to_jiffies(set->gc_int) : HZ;
+	u32 gc_int = READ_ONCE(set->gc_int);
+
+	return gc_int ? msecs_to_jiffies(gc_int) : HZ;
 }
 
 /**
@@ -559,6 +628,7 @@
 };
 
 enum nft_trans_phase;
+void nf_tables_activate_set(const struct nft_ctx *ctx, struct nft_set *set);
 void nf_tables_deactivate_set(const struct nft_ctx *ctx, struct nft_set *set,
 			      struct nft_set_binding *binding,
 			      enum nft_trans_phase phase);
@@ -620,15 +690,18 @@
 /**
  *	struct nft_set_ext - set extensions
  *
- *	@genmask: generation mask
+ *	@genmask: generation mask, but also flags (see NFT_SET_ELEM_DEAD_BIT)
  *	@offset: offsets of individual extension types
  *	@data: beginning of extension data
+ *
+ *	This structure must be aligned to word size, otherwise atomic bitops
+ *	on genmask field can cause alignment failure on some archs.
  */
 struct nft_set_ext {
 	u8	genmask;
 	u8	offset[NFT_SET_EXT_NUM];
 	char	data[];
-};
+} __aligned(BITS_PER_LONG / 8);
 
 static inline void nft_set_ext_prepare(struct nft_set_ext_tmpl *tmpl)
 {
@@ -636,18 +709,22 @@
 	tmpl->len = sizeof(struct nft_set_ext);
 }
 
-static inline void nft_set_ext_add_length(struct nft_set_ext_tmpl *tmpl, u8 id,
-					  unsigned int len)
+static inline int nft_set_ext_add_length(struct nft_set_ext_tmpl *tmpl, u8 id,
+					 unsigned int len)
 {
 	tmpl->len	 = ALIGN(tmpl->len, nft_set_ext_types[id].align);
-	BUG_ON(tmpl->len > U8_MAX);
+	if (tmpl->len > U8_MAX)
+		return -EINVAL;
+
 	tmpl->offset[id] = tmpl->len;
 	tmpl->len	+= nft_set_ext_types[id].len + len;
+
+	return 0;
 }
 
-static inline void nft_set_ext_add(struct nft_set_ext_tmpl *tmpl, u8 id)
+static inline int nft_set_ext_add(struct nft_set_ext_tmpl *tmpl, u8 id)
 {
-	nft_set_ext_add_length(tmpl, id, 0);
+	return nft_set_ext_add_length(tmpl, id, 0);
 }
 
 static inline void nft_set_ext_init(struct nft_set_ext *ext,
@@ -711,10 +788,16 @@
 	return nft_set_ext(ext, NFT_SET_EXT_EXPRESSIONS);
 }
 
-static inline bool nft_set_elem_expired(const struct nft_set_ext *ext)
+static inline bool __nft_set_elem_expired(const struct nft_set_ext *ext,
+					  u64 tstamp)
 {
 	return nft_set_ext_exists(ext, NFT_SET_EXT_EXPIRATION) &&
-	       time_is_before_eq_jiffies64(*nft_set_ext_expiration(ext));
+	       time_after_eq64(tstamp, *nft_set_ext_expiration(ext));
+}
+
+static inline bool nft_set_elem_expired(const struct nft_set_ext *ext)
+{
+	return __nft_set_elem_expired(ext, get_jiffies_64());
 }
 
 static inline struct nft_set_ext *nft_set_elem_ext(const struct nft_set *set,
@@ -740,62 +823,8 @@
 			    struct nft_expr *expr_array[]);
 void nft_set_elem_destroy(const struct nft_set *set, void *elem,
 			  bool destroy_expr);
-
-/**
- *	struct nft_set_gc_batch_head - nf_tables set garbage collection batch
- *
- *	@rcu: rcu head
- *	@set: set the elements belong to
- *	@cnt: count of elements
- */
-struct nft_set_gc_batch_head {
-	struct rcu_head			rcu;
-	const struct nft_set		*set;
-	unsigned int			cnt;
-};
-
-#define NFT_SET_GC_BATCH_SIZE	((PAGE_SIZE -				  \
-				  sizeof(struct nft_set_gc_batch_head)) / \
-				 sizeof(void *))
-
-/**
- *	struct nft_set_gc_batch - nf_tables set garbage collection batch
- *
- * 	@head: GC batch head
- * 	@elems: garbage collection elements
- */
-struct nft_set_gc_batch {
-	struct nft_set_gc_batch_head	head;
-	void				*elems[NFT_SET_GC_BATCH_SIZE];
-};
-
-struct nft_set_gc_batch *nft_set_gc_batch_alloc(const struct nft_set *set,
-						gfp_t gfp);
-void nft_set_gc_batch_release(struct rcu_head *rcu);
-
-static inline void nft_set_gc_batch_complete(struct nft_set_gc_batch *gcb)
-{
-	if (gcb != NULL)
-		call_rcu(&gcb->head.rcu, nft_set_gc_batch_release);
-}
-
-static inline struct nft_set_gc_batch *
-nft_set_gc_batch_check(const struct nft_set *set, struct nft_set_gc_batch *gcb,
-		       gfp_t gfp)
-{
-	if (gcb != NULL) {
-		if (gcb->head.cnt + 1 < ARRAY_SIZE(gcb->elems))
-			return gcb;
-		nft_set_gc_batch_complete(gcb);
-	}
-	return nft_set_gc_batch_alloc(set, gfp);
-}
-
-static inline void nft_set_gc_batch_add(struct nft_set_gc_batch *gcb,
-					void *elem)
-{
-	gcb->elems[gcb->head.cnt++] = elem;
-}
+void nf_tables_set_elem_destroy(const struct nft_ctx *ctx,
+				const struct nft_set *set, void *elem);
 
 struct nft_expr_ops;
 /**
@@ -831,6 +860,7 @@
 
 enum nft_trans_phase {
 	NFT_TRANS_PREPARE,
+	NFT_TRANS_PREPARE_ERROR,
 	NFT_TRANS_ABORT,
 	NFT_TRANS_COMMIT,
 	NFT_TRANS_RELEASE
@@ -858,7 +888,7 @@
 						struct nft_regs *regs,
 						const struct nft_pktinfo *pkt);
 	int				(*clone)(struct nft_expr *dst,
-						 const struct nft_expr *src);
+						 const struct nft_expr *src, gfp_t gfp);
 	unsigned int			size;
 
 	int				(*init)(const struct nft_ctx *ctx,
@@ -883,9 +913,9 @@
 	int				(*offload)(struct nft_offload_ctx *ctx,
 						   struct nft_flow_rule *flow,
 						   const struct nft_expr *expr);
+	bool				(*offload_action)(const struct nft_expr *expr);
 	void				(*offload_stats)(struct nft_expr *expr,
 							 const struct flow_stats *stats);
-	u32				offload_flags;
 	const struct nft_expr_type	*type;
 	void				*data;
 };
@@ -936,7 +966,10 @@
 	return (void *)&rule->data[rule->dlen];
 }
 
-void nf_tables_rule_release(const struct nft_ctx *ctx, struct nft_rule *rule);
+void nft_rule_expr_activate(const struct nft_ctx *ctx, struct nft_rule *rule);
+void nft_rule_expr_deactivate(const struct nft_ctx *ctx, struct nft_rule *rule,
+			      enum nft_trans_phase phase);
+void nf_tables_rule_destroy(const struct nft_ctx *ctx, struct nft_rule *rule);
 
 static inline void nft_set_elem_update_expr(const struct nft_set_ext *ext,
 					    struct nft_regs *regs,
@@ -1001,6 +1034,12 @@
 };
 
 int nft_chain_validate(const struct nft_ctx *ctx, const struct nft_chain *chain);
+int nft_setelem_validate(const struct nft_ctx *ctx, struct nft_set *set,
+			 const struct nft_set_iter *iter,
+			 struct nft_set_elem *elem);
+int nft_set_catchall_validate(const struct nft_ctx *ctx, struct nft_set *set);
+int nf_tables_bind_chain(const struct nft_ctx *ctx, struct nft_chain *chain);
+void nf_tables_unbind_chain(const struct nft_ctx *ctx, struct nft_chain *chain);
 
 enum nft_chain_types {
 	NFT_CHAIN_T_DEFAULT = 0,
@@ -1037,11 +1076,17 @@
 int nft_chain_validate_hooks(const struct nft_chain *chain,
                              unsigned int hook_flags);
 
+static inline bool nft_chain_binding(const struct nft_chain *chain)
+{
+	return chain->flags & NFT_CHAIN_BINDING;
+}
+
 static inline bool nft_chain_is_bound(struct nft_chain *chain)
 {
 	return (chain->flags & NFT_CHAIN_BINDING) && chain->bound;
 }
 
+int nft_chain_add(struct nft_table *table, struct nft_chain *chain);
 void nft_chain_del(struct nft_chain *chain);
 void nf_tables_chain_destroy(struct nft_ctx *ctx);
 
@@ -1053,7 +1098,6 @@
 
 struct nft_hook {
 	struct list_head	list;
-	bool			inactive;
 	struct nf_hook_ops	ops;
 	struct rcu_head		rcu;
 };
@@ -1094,6 +1138,29 @@
 
 unsigned int nft_do_chain(struct nft_pktinfo *pkt, void *priv);
 
+static inline bool nft_use_inc(u32 *use)
+{
+	if (*use == UINT_MAX)
+		return false;
+
+	(*use)++;
+
+	return true;
+}
+
+static inline void nft_use_dec(u32 *use)
+{
+	WARN_ON_ONCE((*use)-- == 0);
+}
+
+/* For error and abort path: restore use counter to previous state. */
+static inline void nft_use_inc_restore(u32 *use)
+{
+	WARN_ON_ONCE(!nft_use_inc(use));
+}
+
+#define nft_use_dec_restore	nft_use_dec
+
 /**
  *	struct nft_table - nf_tables table
  *
@@ -1177,8 +1244,8 @@
 	struct list_head		list;
 	struct rhlist_head		rhlhead;
 	struct nft_object_hash_key	key;
-	u32				genmask:2,
-					use:30;
+	u32				genmask:2;
+	u32				use;
 	u64				handle;
 	u16				udlen;
 	u8				*udata;
@@ -1213,6 +1280,7 @@
  *	@type: stateful object numeric type
  *	@owner: module owner
  *	@maxattr: maximum netlink attribute
+ *	@family: address family for AF-specific object types
  *	@policy: netlink attribute policy
  */
 struct nft_object_type {
@@ -1222,6 +1290,7 @@
 	struct list_head		list;
 	u32				type;
 	unsigned int                    maxattr;
+	u8				family;
 	struct module			*owner;
 	const struct nla_policy		*policy;
 };
@@ -1280,8 +1349,8 @@
 	char				*name;
 	int				hooknum;
 	int				ops_len;
-	u32				genmask:2,
-					use:30;
+	u32				genmask:2;
+	u32				use;
 	u64				handle;
 	/* runtime data below here */
 	struct list_head		hook_list ____cacheline_aligned;
@@ -1417,45 +1486,37 @@
 
 #endif /* IS_ENABLED(CONFIG_NF_TABLES) */
 
-/*
- * We use a free bit in the genmask field to indicate the element
- * is busy, meaning it is currently being processed either by
- * the netlink API or GC.
- *
- * Even though the genmask is only a single byte wide, this works
- * because the extension structure if fully constant once initialized,
- * so there are no non-atomic write accesses unless it is already
- * marked busy.
- */
-#define NFT_SET_ELEM_BUSY_MASK	(1 << 2)
+#define NFT_SET_ELEM_DEAD_MASK	(1 << 2)
 
 #if defined(__LITTLE_ENDIAN_BITFIELD)
-#define NFT_SET_ELEM_BUSY_BIT	2
+#define NFT_SET_ELEM_DEAD_BIT	2
 #elif defined(__BIG_ENDIAN_BITFIELD)
-#define NFT_SET_ELEM_BUSY_BIT	(BITS_PER_LONG - BITS_PER_BYTE + 2)
+#define NFT_SET_ELEM_DEAD_BIT	(BITS_PER_LONG - BITS_PER_BYTE + 2)
 #else
 #error
 #endif
 
-static inline int nft_set_elem_mark_busy(struct nft_set_ext *ext)
+static inline void nft_set_elem_dead(struct nft_set_ext *ext)
 {
 	unsigned long *word = (unsigned long *)ext;
 
 	BUILD_BUG_ON(offsetof(struct nft_set_ext, genmask) != 0);
-	return test_and_set_bit(NFT_SET_ELEM_BUSY_BIT, word);
+	set_bit(NFT_SET_ELEM_DEAD_BIT, word);
 }
 
-static inline void nft_set_elem_clear_busy(struct nft_set_ext *ext)
+static inline int nft_set_elem_is_dead(const struct nft_set_ext *ext)
 {
 	unsigned long *word = (unsigned long *)ext;
 
-	clear_bit(NFT_SET_ELEM_BUSY_BIT, word);
+	BUILD_BUG_ON(offsetof(struct nft_set_ext, genmask) != 0);
+	return test_bit(NFT_SET_ELEM_DEAD_BIT, word);
 }
 
 /**
  *	struct nft_trans - nf_tables object update in transaction
  *
  *	@list: used internally
+ *	@binding_list: list of objects with possible bindings
  *	@msg_type: message type
  *	@put_net: ctx->net needs to be put
  *	@ctx: transaction context
@@ -1463,6 +1524,7 @@
  */
 struct nft_trans {
 	struct list_head		list;
+	struct list_head		binding_list;
 	int				msg_type;
 	bool				put_net;
 	struct nft_ctx			ctx;
@@ -1473,6 +1535,7 @@
 	struct nft_rule			*rule;
 	struct nft_flow_rule		*flow;
 	u32				rule_id;
+	bool				bound;
 };
 
 #define nft_trans_rule(trans)	\
@@ -1481,10 +1544,15 @@
 	(((struct nft_trans_rule *)trans->data)->flow)
 #define nft_trans_rule_id(trans)	\
 	(((struct nft_trans_rule *)trans->data)->rule_id)
+#define nft_trans_rule_bound(trans)	\
+	(((struct nft_trans_rule *)trans->data)->bound)
 
 struct nft_trans_set {
 	struct nft_set			*set;
 	u32				set_id;
+	u32				gc_int;
+	u64				timeout;
+	bool				update;
 	bool				bound;
 };
 
@@ -1494,15 +1562,25 @@
 	(((struct nft_trans_set *)trans->data)->set_id)
 #define nft_trans_set_bound(trans)	\
 	(((struct nft_trans_set *)trans->data)->bound)
+#define nft_trans_set_update(trans)	\
+	(((struct nft_trans_set *)trans->data)->update)
+#define nft_trans_set_timeout(trans)	\
+	(((struct nft_trans_set *)trans->data)->timeout)
+#define nft_trans_set_gc_int(trans)	\
+	(((struct nft_trans_set *)trans->data)->gc_int)
 
 struct nft_trans_chain {
+	struct nft_chain		*chain;
 	bool				update;
 	char				*name;
 	struct nft_stats __percpu	*stats;
 	u8				policy;
+	bool				bound;
 	u32				chain_id;
 };
 
+#define nft_trans_chain(trans)	\
+	(((struct nft_trans_chain *)trans->data)->chain)
 #define nft_trans_chain_update(trans)	\
 	(((struct nft_trans_chain *)trans->data)->update)
 #define nft_trans_chain_name(trans)	\
@@ -1511,6 +1589,8 @@
 	(((struct nft_trans_chain *)trans->data)->stats)
 #define nft_trans_chain_policy(trans)	\
 	(((struct nft_trans_chain *)trans->data)->policy)
+#define nft_trans_chain_bound(trans)	\
+	(((struct nft_trans_chain *)trans->data)->bound)
 #define nft_trans_chain_id(trans)	\
 	(((struct nft_trans_chain *)trans->data)->chain_id)
 
@@ -1563,6 +1643,39 @@
 #define nft_trans_flowtable_flags(trans)	\
 	(((struct nft_trans_flowtable *)trans->data)->flags)
 
+#define NFT_TRANS_GC_BATCHCOUNT	256
+
+struct nft_trans_gc {
+	struct list_head	list;
+	struct net		*net;
+	struct nft_set		*set;
+	u32			seq;
+	u16			count;
+	void			*priv[NFT_TRANS_GC_BATCHCOUNT];
+	struct rcu_head		rcu;
+};
+
+struct nft_trans_gc *nft_trans_gc_alloc(struct nft_set *set,
+					unsigned int gc_seq, gfp_t gfp);
+void nft_trans_gc_destroy(struct nft_trans_gc *trans);
+
+struct nft_trans_gc *nft_trans_gc_queue_async(struct nft_trans_gc *gc,
+					      unsigned int gc_seq, gfp_t gfp);
+void nft_trans_gc_queue_async_done(struct nft_trans_gc *gc);
+
+struct nft_trans_gc *nft_trans_gc_queue_sync(struct nft_trans_gc *gc, gfp_t gfp);
+void nft_trans_gc_queue_sync_done(struct nft_trans_gc *trans);
+
+void nft_trans_gc_elem_add(struct nft_trans_gc *gc, void *priv);
+
+struct nft_trans_gc *nft_trans_gc_catchall_async(struct nft_trans_gc *gc,
+						 unsigned int gc_seq);
+struct nft_trans_gc *nft_trans_gc_catchall_sync(struct nft_trans_gc *gc);
+
+void nft_setelem_data_deactivate(const struct net *net,
+				 const struct nft_set *set,
+				 struct nft_set_elem *elem);
+
 int __init nft_chain_filter_init(void);
 void nft_chain_filter_fini(void);
 
@@ -1583,10 +1696,14 @@
 struct nftables_pernet {
 	struct list_head	tables;
 	struct list_head	commit_list;
+	struct list_head	binding_list;
 	struct list_head	module_list;
 	struct list_head	notify_list;
 	struct mutex		commit_mutex;
+	u64			table_handle;
+	u64			tstamp;
 	unsigned int		base_seq;
+	unsigned int		gc_seq;
 	u8			validate_state;
 };
 
@@ -1597,4 +1714,9 @@
 	return net_generic(net, nf_tables_net_id);
 }
 
+static inline u64 nft_net_tstamp(const struct net *net)
+{
+	return nft_pernet(net)->tstamp;
+}
+
 #endif /* _NET_NF_TABLES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_tables_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_tables_core.h
@@ -40,6 +40,14 @@
 	bool			inv;
 };
 
+struct nft_cmp16_fast_expr {
+	struct nft_data		data;
+	struct nft_data		mask;
+	u8			sreg;
+	u8			len;
+	bool			inv;
+};
+
 struct nft_immediate_expr {
 	struct nft_data		data;
 	u8			dreg;
@@ -57,6 +65,7 @@
 }
 
 extern const struct nft_expr_ops nft_cmp_fast_ops;
+extern const struct nft_expr_ops nft_cmp16_fast_ops;
 
 struct nft_payload {
 	enum nft_payload_bases	base:8;
@@ -65,16 +74,6 @@
 	u8			dreg;
 };
 
-struct nft_payload_set {
-	enum nft_payload_bases	base:8;
-	u8			offset;
-	u8			len;
-	u8			sreg;
-	u8			csum_type;
-	u8			csum_offset;
-	u8			csum_flags;
-};
-
 extern const struct nft_expr_ops nft_payload_fast_ops;
 
 extern const struct nft_expr_ops nft_bitwise_fast_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_tables_ipv4.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_tables_ipv4.h
@@ -10,7 +10,7 @@
 	struct iphdr *ip;
 
 	ip = ip_hdr(pkt->skb);
-	pkt->tprot_set = true;
+	pkt->flags = NFT_PKTINFO_L4PROTO;
 	pkt->tprot = ip->protocol;
 	pkt->thoff = ip_hdrlen(pkt->skb);
 	pkt->fragoff = ntohs(ip->frag_off) & IP_OFFSET;
@@ -36,7 +36,7 @@
 	else if (len < thoff)
 		return -1;
 
-	pkt->tprot_set = true;
+	pkt->flags = NFT_PKTINFO_L4PROTO;
 	pkt->tprot = iph->protocol;
 	pkt->thoff = thoff;
 	pkt->fragoff = ntohs(iph->frag_off) & IP_OFFSET;
@@ -71,7 +71,7 @@
 		goto inhdr_error;
 	}
 
-	pkt->tprot_set = true;
+	pkt->flags = NFT_PKTINFO_L4PROTO;
 	pkt->tprot = iph->protocol;
 	pkt->thoff = thoff;
 	pkt->fragoff = ntohs(iph->frag_off) & IP_OFFSET;
@@ -82,4 +82,5 @@
 	__IP_INC_STATS(nft_net(pkt), IPSTATS_MIB_INHDRERRORS);
 	return -1;
 }
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_tables_ipv6.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_tables_ipv6.h
@@ -18,7 +18,7 @@
 		return;
 	}
 
-	pkt->tprot_set = true;
+	pkt->flags = NFT_PKTINFO_L4PROTO;
 	pkt->tprot = protohdr;
 	pkt->thoff = thoff;
 	pkt->fragoff = frag_off;
@@ -50,7 +50,7 @@
 	if (protohdr < 0)
 		return -1;
 
-	pkt->tprot_set = true;
+	pkt->flags = NFT_PKTINFO_L4PROTO;
 	pkt->tprot = protohdr;
 	pkt->thoff = thoff;
 	pkt->fragoff = frag_off;
@@ -96,7 +96,7 @@
 	if (protohdr < 0)
 		goto inhdr_error;
 
-	pkt->tprot_set = true;
+	pkt->flags = NFT_PKTINFO_L4PROTO;
 	pkt->tprot = protohdr;
 	pkt->thoff = thoff;
 	pkt->fragoff = frag_off;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_tables_offload.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_tables_offload.h
@@ -67,8 +67,6 @@
 	struct flow_rule	*rule;
 };
 
-#define NFT_OFFLOAD_F_ACTION	(1 << 0)
-
 void nft_flow_rule_set_addr_type(struct nft_flow_rule *flow,
 				 enum flow_dissector_key_id addr_type);
 
@@ -94,7 +92,7 @@
 	NFT_OFFLOAD_MATCH(__key, __base, __field, __len, __reg)		\
 	memset(&(__reg)->mask, 0xff, (__reg)->len);
 
-int nft_chain_offload_priority(struct nft_base_chain *basechain);
+bool nft_chain_offload_support(const struct nft_base_chain *basechain);
 
 int nft_offload_init(void);
 void nft_offload_exit(void);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netfilter/nf_tproxy.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netfilter/nf_tproxy.h
@@ -17,6 +17,13 @@
 	return false;
 }
 
+static inline void nf_tproxy_twsk_deschedule_put(struct inet_timewait_sock *tw)
+{
+	local_bh_disable();
+	inet_twsk_deschedule_put(tw);
+	local_bh_enable();
+}
+
 /* assign a socket to the skb -- consumes sk */
 static inline void nf_tproxy_assign_sock(struct sk_buff *skb, struct sock *sk)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netlabel.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netlabel.h
@@ -97,7 +97,7 @@
 
 /* NetLabel audit information */
 struct netlbl_audit {
-	u32 secid;
+	struct lsmblob lsmdata;
 	kuid_t loginuid;
 	unsigned int sessionid;
 };
@@ -166,7 +166,7 @@
  * @attr.mls: MLS sensitivity label
  * @attr.mls.cat: MLS category bitmap
  * @attr.mls.lvl: MLS sensitivity level
- * @attr.secid: LSM specific secid token
+ * @attr.lsmblob: LSM specific data
  *
  * Description:
  * This structure is used to pass security attributes between NetLabel and the
@@ -201,7 +201,7 @@
 			struct netlbl_lsm_catmap *cat;
 			u32 lvl;
 		} mls;
-		u32 secid;
+		struct lsmblob lsmblob;
 	} attr;
 };
 
@@ -415,7 +415,7 @@
 				const void *addr,
 				const void *mask,
 				u16 family,
-				u32 secid,
+				struct lsmblob *lsmblob,
 				struct netlbl_audit *audit_info);
 int netlbl_cfg_unlbl_static_del(struct net *net,
 				const char *dev_name,
@@ -523,7 +523,7 @@
 					      const void *addr,
 					      const void *mask,
 					      u16 family,
-					      u32 secid,
+					      struct lsmblob *lsmblob,
 					      struct netlbl_audit *audit_info)
 {
 	return -ENOSYS;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netns/flow_table.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netns/flow_table.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __NETNS_FLOW_TABLE_H
+#define __NETNS_FLOW_TABLE_H
+
+struct nf_flow_table_stat {
+	unsigned int count_wq_add;
+	unsigned int count_wq_del;
+	unsigned int count_wq_stats;
+};
+
+struct netns_ft {
+	struct nf_flow_table_stat __percpu *stat;
+};
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netns/ipv4.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netns/ipv4.h
@@ -65,7 +65,7 @@
 	bool			fib_has_custom_local_routes;
 	bool			fib_offload_disabled;
 #ifdef CONFIG_IP_ROUTE_CLASSID
-	int			fib_num_tclassid_users;
+	atomic_t		fib_num_tclassid_users;
 #endif
 	struct hlist_head	*fib_table_hash;
 	struct sock		*fibnl;
@@ -74,7 +74,6 @@
 	struct sock		*mc_autojoin_sk;
 
 	struct inet_peer_base	*peers;
-	struct sock  * __percpu	*tcp_sk;
 	struct fqdir		*fqdir;
 
 	u8 sysctl_icmp_echo_ignore_all;
@@ -85,6 +84,9 @@
 	int sysctl_icmp_ratelimit;
 	int sysctl_icmp_ratemask;
 
+	u32 ip_rt_min_pmtu;
+	int ip_rt_mtu_expires;
+
 	struct local_ports ip_local_ports;
 
 	u8 sysctl_tcp_ecn;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netns/ipv6.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netns/ipv6.h
@@ -53,7 +53,7 @@
 	int seg6_flowlabel;
 	u32 ioam6_id;
 	u64 ioam6_id_wide;
-	bool skip_notify_on_dev_down;
+	int skip_notify_on_dev_down;
 	u8 fib_notify_on_flag_change;
 };
 
@@ -75,11 +75,12 @@
 	struct list_head	fib6_walkers;
 	rwlock_t		fib6_walker_lock;
 	spinlock_t		fib6_gc_lock;
-	unsigned int		 ip6_rt_gc_expire;
-	unsigned long		 ip6_rt_last_gc;
+	atomic_t		ip6_rt_gc_expire;
+	unsigned long		ip6_rt_last_gc;
+	unsigned char		flowlabel_has_excl;
 #ifdef CONFIG_IPV6_MULTIPLE_TABLES
-	unsigned int		fib6_rules_require_fldissect;
 	bool			fib6_has_custom_rules;
+	unsigned int		fib6_rules_require_fldissect;
 #ifdef CONFIG_IPV6_SUBTREES
 	unsigned int		fib6_routes_require_src;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netns/netfilter.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netns/netfilter.h
@@ -24,9 +24,6 @@
 #ifdef CONFIG_NETFILTER_FAMILY_BRIDGE
 	struct nf_hook_entries __rcu *hooks_bridge[NF_INET_NUMHOOKS];
 #endif
-#if IS_ENABLED(CONFIG_DECNET)
-	struct nf_hook_entries __rcu *hooks_decnet[NF_DN_NUMHOOKS];
-#endif
 #if IS_ENABLED(CONFIG_NF_DEFRAG_IPV4)
 	unsigned int defrag_ipv4_users;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/netns/xfrm.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/netns/xfrm.h
@@ -50,6 +50,7 @@
 	struct list_head	policy_all;
 	struct hlist_head	*policy_byidx;
 	unsigned int		policy_idx_hmask;
+	unsigned int		idx_generator;
 	struct hlist_head	policy_inexact[XFRM_POLICY_MAX];
 	struct xfrm_policy_hash	policy_bydst[XFRM_POLICY_MAX];
 	unsigned int		policy_count[XFRM_POLICY_MAX * 2];
@@ -66,11 +67,7 @@
 	int			sysctl_larval_drop;
 	u32			sysctl_acq_expires;
 
-	u8			policy_default;
-#define XFRM_POL_DEFAULT_IN	1
-#define XFRM_POL_DEFAULT_OUT	2
-#define XFRM_POL_DEFAULT_FWD	4
-#define XFRM_POL_DEFAULT_MASK	7
+	u8			policy_default[XFRM_POLICY_MAX];
 
 #ifdef CONFIG_SYSCTL
 	struct ctl_table_header	*sysctl_hdr;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/nfc/nci_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/nfc/nci_core.h
@@ -30,6 +30,7 @@
 	NCI_UP,
 	NCI_DATA_EXCHANGE,
 	NCI_DATA_EXCHANGE_TO,
+	NCI_UNREG,
 };
 
 /* NCI device states */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/nl802154.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/nl802154.h
@@ -19,6 +19,8 @@
  *
  */
 
+#include <linux/types.h>
+
 #define NL802154_GENL_NAME "nl802154"
 
 enum nl802154_commands {
@@ -150,10 +152,9 @@
 };
 
 enum nl802154_iftype {
-	/* for backwards compatibility TODO */
-	NL802154_IFTYPE_UNSPEC = -1,
+	NL802154_IFTYPE_UNSPEC = (~(__u32)0),
 
-	NL802154_IFTYPE_NODE,
+	NL802154_IFTYPE_NODE = 0,
 	NL802154_IFTYPE_MONITOR,
 	NL802154_IFTYPE_COORD,
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/page_pool.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/page_pool.h
@@ -282,22 +282,4 @@
 		page_pool_update_nid(pool, new_nid);
 }
 
-static inline void page_pool_ring_lock(struct page_pool *pool)
-	__acquires(&pool->ring.producer_lock)
-{
-	if (in_serving_softirq())
-		spin_lock(&pool->ring.producer_lock);
-	else
-		spin_lock_bh(&pool->ring.producer_lock);
-}
-
-static inline void page_pool_ring_unlock(struct page_pool *pool)
-	__releases(&pool->ring.producer_lock)
-{
-	if (in_serving_softirq())
-		spin_unlock(&pool->ring.producer_lock);
-	else
-		spin_unlock_bh(&pool->ring.producer_lock);
-}
-
 #endif /* _NET_PAGE_POOL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/pkt_sched.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/pkt_sched.h
@@ -134,12 +134,14 @@
 	}
 }
 
+extern const struct nla_policy rtm_tca_policy[TCA_MAX + 1];
+
 /* Calculate maximal size of packet seen by hard_start_xmit
    routine of this device.
  */
 static inline unsigned int psched_mtu(const struct net_device *dev)
 {
-	return dev->mtu + dev->hard_header_len;
+	return READ_ONCE(dev->mtu) + dev->hard_header_len;
 }
 
 static inline struct net *qdisc_net(struct Qdisc *q)
@@ -193,4 +195,22 @@
 	skb->tstamp = ktime_set(0, 0);
 }
 
+struct tc_skb_cb {
+	struct qdisc_skb_cb qdisc_cb;
+
+	u16 mru;
+	u8 post_ct:1;
+	u8 post_ct_snat:1;
+	u8 post_ct_dnat:1;
+	u16 zone; /* Only valid if post_ct = true */
+};
+
+static inline struct tc_skb_cb *tc_skb_cb(const struct sk_buff *skb)
+{
+	struct tc_skb_cb *cb = (struct tc_skb_cb *)skb->cb;
+
+	BUILD_BUG_ON(sizeof(*cb) > sizeof_field(struct sk_buff, cb));
+	return cb;
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/protocol.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/protocol.h
@@ -35,8 +35,6 @@
 
 /* This is used to register protocols. */
 struct net_protocol {
-	int			(*early_demux)(struct sk_buff *skb);
-	int			(*early_demux_handler)(struct sk_buff *skb);
 	int			(*handler)(struct sk_buff *skb);
 
 	/* This returns an error if we weren't able to handle the error. */
@@ -52,8 +50,6 @@
 
 #if IS_ENABLED(CONFIG_IPV6)
 struct inet6_protocol {
-	void	(*early_demux)(struct sk_buff *skb);
-	void    (*early_demux_handler)(struct sk_buff *skb);
 	int	(*handler)(struct sk_buff *skb);
 
 	/* This returns an error if we weren't able to handle the error. */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/raw.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/raw.h
@@ -75,7 +75,7 @@
 				       int dif, int sdif)
 {
 #if IS_ENABLED(CONFIG_NET_L3_MASTER_DEV)
-	return inet_bound_dev_eq(!!net->ipv4.sysctl_raw_l3mdev_accept,
+	return inet_bound_dev_eq(READ_ONCE(net->ipv4.sysctl_raw_l3mdev_accept),
 				 bound_dev_if, dif, sdif);
 #else
 	return inet_bound_dev_eq(true, bound_dev_if, dif, sdif);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/request_sock.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/request_sock.h
@@ -70,6 +70,7 @@
 	struct saved_syn		*saved_syn;
 	u32				secid;
 	u32				peer_secid;
+	u32				timeout;
 };
 
 static inline struct request_sock *inet_reqsk(const struct sock *sk)
@@ -104,6 +105,7 @@
 	sk_node_init(&req_to_sk(req)->sk_node);
 	sk_tx_queue_clear(req_to_sk(req));
 	req->saved_syn = NULL;
+	req->timeout = 0;
 	req->num_timeout = 0;
 	req->num_retrans = 0;
 	req->sk = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/route.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/route.h
@@ -357,10 +357,15 @@
 static inline int ip4_dst_hoplimit(const struct dst_entry *dst)
 {
 	int hoplimit = dst_metric_raw(dst, RTAX_HOPLIMIT);
-	struct net *net = dev_net(dst->dev);
 
-	if (hoplimit == 0)
-		hoplimit = net->ipv4.sysctl_ip_default_ttl;
+	if (hoplimit == 0) {
+		const struct net *net;
+
+		rcu_read_lock();
+		net = dev_net_rcu(dst->dev);
+		hoplimit = READ_ONCE(net->ipv4.sysctl_ip_default_ttl);
+		rcu_read_unlock();
+	}
 	return hoplimit;
 }
 
@@ -369,7 +374,7 @@
 {
 	struct neighbour *neigh;
 
-	neigh = __ipv4_neigh_lookup_noref(dev, daddr);
+	neigh = __ipv4_neigh_lookup_noref(dev, (__force u32)daddr);
 	if (unlikely(!neigh))
 		neigh = __neigh_create(&arp_tbl, &daddr, dev, false);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/rpl.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/rpl.h
@@ -23,9 +23,6 @@
 static inline void rpl_exit(void) {}
 #endif
 
-/* Worst decompression memory usage ipv6 address (16) + pad 7 */
-#define IPV6_RPL_SRH_WORST_SWAP_SIZE (sizeof(struct in6_addr) + 7)
-
 size_t ipv6_rpl_srh_size(unsigned char n, unsigned char cmpri,
 			 unsigned char cmpre);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/rtnetlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/rtnetlink.h
@@ -13,6 +13,22 @@
 	RTNL_FLAG_DOIT_UNLOCKED = 1,
 };
 
+enum rtnl_kinds {
+	RTNL_KIND_NEW,
+	RTNL_KIND_DEL,
+	RTNL_KIND_GET,
+	RTNL_KIND_SET
+};
+
+struct rtnl_msg_handler {
+	struct module *owner;
+	int protocol;
+	int msgtype;
+	rtnl_doit_func doit;
+	rtnl_dumpit_func dumpit;
+	int flags;
+};
+
 void rtnl_register(int protocol, int msgtype,
 		   rtnl_doit_func, rtnl_dumpit_func, unsigned int flags);
 int rtnl_register_module(struct module *owner, int protocol, int msgtype,
@@ -20,6 +36,14 @@
 int rtnl_unregister(int protocol, int msgtype);
 void rtnl_unregister_all(int protocol);
 
+int __rtnl_register_many(const struct rtnl_msg_handler *handlers, int n);
+void __rtnl_unregister_many(const struct rtnl_msg_handler *handlers, int n);
+
+#define rtnl_register_many(handlers)				\
+	__rtnl_register_many(handlers, ARRAY_SIZE(handlers))
+#define rtnl_unregister_many(handlers)				\
+	__rtnl_unregister_many(handlers, ARRAY_SIZE(handlers))
+
 static inline int rtnl_msg_family(const struct nlmsghdr *nlh)
 {
 	if (nlmsg_len(nlh) >= sizeof(struct rtgenmsg))
@@ -175,8 +199,8 @@
 int rtnl_delete_link(struct net_device *dev);
 int rtnl_configure_link(struct net_device *dev, const struct ifinfomsg *ifm);
 
-int rtnl_nla_parse_ifla(struct nlattr **tb, const struct nlattr *head, int len,
-			struct netlink_ext_ack *exterr);
+int rtnl_nla_parse_ifinfomsg(struct nlattr **tb, const struct nlattr *nla_peer,
+			     struct netlink_ext_ack *exterr);
 struct net *rtnl_get_net_ns_capable(struct sock *sk, int netnsid);
 
 #define MODULE_ALIAS_RTNL_LINK(kind) MODULE_ALIAS("rtnl-link-" kind)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/sch_generic.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/sch_generic.h
@@ -173,37 +173,17 @@
 		if (spin_trylock(&qdisc->seqlock))
 			return true;
 
-		/* Paired with smp_mb__after_atomic() to make sure
-		 * STATE_MISSED checking is synchronized with clearing
-		 * in pfifo_fast_dequeue().
+		/* No need to insist if the MISSED flag was already set.
+		 * Note that test_and_set_bit() also gives us memory ordering
+		 * guarantees wrt potential earlier enqueue() and below
+		 * spin_trylock(), both of which are necessary to prevent races
 		 */
-		smp_mb__before_atomic();
-
-		/* If the MISSED flag is set, it means other thread has
-		 * set the MISSED flag before second spin_trylock(), so
-		 * we can return false here to avoid multi cpus doing
-		 * the set_bit() and second spin_trylock() concurrently.
-		 */
-		if (test_bit(__QDISC_STATE_MISSED, &qdisc->state))
+		if (test_and_set_bit(__QDISC_STATE_MISSED, &qdisc->state))
 			return false;
 
-		/* Set the MISSED flag before the second spin_trylock(),
-		 * if the second spin_trylock() return false, it means
-		 * other cpu holding the lock will do dequeuing for us
-		 * or it will see the MISSED flag set after releasing
-		 * lock and reschedule the net_tx_action() to do the
-		 * dequeuing.
-		 */
-		set_bit(__QDISC_STATE_MISSED, &qdisc->state);
-
-		/* spin_trylock() only has load-acquire semantic, so use
-		 * smp_mb__after_atomic() to ensure STATE_MISSED is set
-		 * before doing the second spin_trylock().
-		 */
-		smp_mb__after_atomic();
-
-		/* Retry again in case other CPU may not see the new flag
-		 * after it releases the lock at the end of qdisc_run_end().
+		/* Try to take the lock again to make sure that we will either
+		 * grab it or the CPU that still has it will see MISSED set
+		 * when testing it in qdisc_run_end()
 		 */
 		return spin_trylock(&qdisc->seqlock);
 	} else if (qdisc_is_running(qdisc)) {
@@ -222,6 +202,12 @@
 	if (qdisc->flags & TCQ_F_NOLOCK) {
 		spin_unlock(&qdisc->seqlock);
 
+		/* spin_unlock() only has store-release semantic. The unlock
+		 * and test_bit() ordering is a store-load ordering, so a full
+		 * memory barrier is needed here.
+		 */
+		smp_mb();
+
 		if (unlikely(test_bit(__QDISC_STATE_MISSED,
 				      &qdisc->state)))
 			__netif_schedule(qdisc);
@@ -308,6 +294,8 @@
 					  struct netlink_ext_ack *extack);
 	void			(*attach)(struct Qdisc *sch);
 	int			(*change_tx_queue_len)(struct Qdisc *, unsigned int);
+	void			(*change_real_num_tx)(struct Qdisc *sch,
+						      unsigned int new_real_tx);
 
 	int			(*dump)(struct Qdisc *, struct sk_buff *);
 	int			(*dump_stats)(struct Qdisc *, struct gnet_dump *);
@@ -379,7 +367,10 @@
 						struct nlattr **tca,
 						struct netlink_ext_ack *extack);
 	void			(*tmplt_destroy)(void *tmplt_priv);
-
+	void			(*tmplt_reoffload)(struct tcf_chain *chain,
+						   bool add,
+						   flow_setup_cb_t *cb,
+						   void *cb_priv);
 	/* rtnetlink specific */
 	int			(*dump)(struct net*, struct tcf_proto*, void *,
 					struct sk_buff *skb, struct tcmsg*,
@@ -438,8 +429,6 @@
 	};
 #define QDISC_CB_PRIV_LEN 20
 	unsigned char		data[QDISC_CB_PRIV_LEN];
-	u16			mru;
-	bool			post_ct;
 };
 
 typedef void tcf_chain_head_change_t(struct tcf_proto *tp_head, void *priv);
@@ -684,6 +673,8 @@
 void qdisc_class_hash_destroy(struct Qdisc_class_hash *);
 
 int dev_qdisc_change_tx_queue_len(struct net_device *dev);
+void dev_qdisc_change_real_num_tx(struct net_device *dev,
+				  unsigned int new_real_tx);
 void dev_init_scheduler(struct net_device *dev);
 void dev_shutdown(struct net_device *dev);
 void dev_activate(struct net_device *dev);
@@ -841,7 +832,6 @@
 static inline int qdisc_enqueue(struct sk_buff *skb, struct Qdisc *sch,
 				struct sk_buff **to_free)
 {
-	qdisc_calculate_pkt_len(skb, sch);
 	return sch->enqueue(skb, sch, to_free);
 }
 
@@ -1189,7 +1179,6 @@
 static inline void qdisc_reset_queue(struct Qdisc *sch)
 {
 	__qdisc_reset_queue(&sch->q);
-	sch->qstats.backlog = 0;
 }
 
 static inline struct Qdisc *qdisc_replace(struct Qdisc *sch, struct Qdisc *new,
@@ -1258,6 +1247,7 @@
 	u64	rate_bytes_ps; /* bytes per second */
 	u32	mult;
 	u16	overhead;
+	u16	mpu;
 	u8	linklayer;
 	u8	shift;
 };
@@ -1267,6 +1257,9 @@
 {
 	len += r->overhead;
 
+	if (len < r->mpu)
+		len = r->mpu;
+
 	if (unlikely(r->linklayer == TC_LINKLAYER_ATM))
 		return ((u64)(DIV_ROUND_UP(len,48)*53) * r->mult) >> r->shift;
 
@@ -1289,6 +1282,7 @@
 	res->rate = min_t(u64, r->rate_bytes_ps, ~0U);
 
 	res->overhead = r->overhead;
+	res->mpu = r->mpu;
 	res->linklayer = (r->linklayer & TC_LINKLAYER_MASK);
 }
 
@@ -1343,4 +1337,11 @@
 
 int sch_frag_xmit_hook(struct sk_buff *skb, int (*xmit)(struct sk_buff *skb));
 
+/* Make sure qdisc is no longer in SCHED state. */
+static inline void qdisc_synchronize(const struct Qdisc *q)
+{
+	while (test_bit(__QDISC_STATE_SCHED, &q->state))
+		msleep(1);
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/scm.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/scm.h
@@ -33,7 +33,7 @@
 	struct scm_fp_list	*fp;		/* Passed files		*/
 	struct scm_creds	creds;		/* Skb credentials	*/
 #ifdef CONFIG_SECURITY_NETWORK
-	u32			secid;		/* Passed security ID 	*/
+	struct lsmblob		lsmblob;	/* Passed LSM data	*/
 #endif
 };
 
@@ -46,7 +46,7 @@
 #ifdef CONFIG_SECURITY_NETWORK
 static __inline__ void unix_get_peersec_dgram(struct socket *sock, struct scm_cookie *scm)
 {
-	security_socket_getpeersec_dgram(sock, NULL, &scm->secid);
+	security_socket_getpeersec_dgram(sock, NULL, &scm->lsmblob);
 }
 #else
 static __inline__ void unix_get_peersec_dgram(struct socket *sock, struct scm_cookie *scm)
@@ -92,29 +92,41 @@
 #ifdef CONFIG_SECURITY_NETWORK
 static inline void scm_passec(struct socket *sock, struct msghdr *msg, struct scm_cookie *scm)
 {
-	char *secdata;
-	u32 seclen;
+	struct lsmcontext context;
 	int err;
 
 	if (test_bit(SOCK_PASSSEC, &sock->flags)) {
-		err = security_secid_to_secctx(scm->secid, &secdata, &seclen);
+		err = security_secid_to_secctx(&scm->lsmblob, &context,
+					       LSMBLOB_DISPLAY);
 
 		if (!err) {
-			put_cmsg(msg, SOL_SOCKET, SCM_SECURITY, seclen, secdata);
-			security_release_secctx(secdata, seclen);
+			put_cmsg(msg, SOL_SOCKET, SCM_SECURITY,
+				 context.len, context.context);
+			security_release_secctx(&context);
 		}
 	}
 }
+
+static inline bool scm_has_secdata(struct socket *sock)
+{
+	return test_bit(SOCK_PASSSEC, &sock->flags);
+}
 #else
 static inline void scm_passec(struct socket *sock, struct msghdr *msg, struct scm_cookie *scm)
 { }
+
+static inline bool scm_has_secdata(struct socket *sock)
+{
+	return false;
+}
 #endif /* CONFIG_SECURITY_NETWORK */
 
 static __inline__ void scm_recv(struct socket *sock, struct msghdr *msg,
 				struct scm_cookie *scm, int flags)
 {
 	if (!msg->msg_control) {
-		if (test_bit(SOCK_PASSCRED, &sock->flags) || scm->fp)
+		if (test_bit(SOCK_PASSCRED, &sock->flags) || scm->fp ||
+		    scm_has_secdata(sock))
 			msg->msg_flags |= MSG_CTRUNC;
 		scm_destroy(scm);
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/sctp/sctp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/sctp/sctp.h
@@ -105,19 +105,18 @@
 int sctp_asconf_mgmt(struct sctp_sock *, struct sctp_sockaddr_entry *);
 struct sk_buff *sctp_skb_recv_datagram(struct sock *, int, int, int *);
 
+typedef int (*sctp_callback_t)(struct sctp_endpoint *, struct sctp_transport *, void *);
 void sctp_transport_walk_start(struct rhashtable_iter *iter);
 void sctp_transport_walk_stop(struct rhashtable_iter *iter);
 struct sctp_transport *sctp_transport_get_next(struct net *net,
 			struct rhashtable_iter *iter);
 struct sctp_transport *sctp_transport_get_idx(struct net *net,
 			struct rhashtable_iter *iter, int pos);
-int sctp_transport_lookup_process(int (*cb)(struct sctp_transport *, void *),
-				  struct net *net,
+int sctp_transport_lookup_process(sctp_callback_t cb, struct net *net,
 				  const union sctp_addr *laddr,
 				  const union sctp_addr *paddr, void *p);
-int sctp_for_each_transport(int (*cb)(struct sctp_transport *, void *),
-			    int (*cb_done)(struct sctp_transport *, void *),
-			    struct net *net, int *pos, void *p);
+int sctp_transport_traverse_process(sctp_callback_t cb, sctp_callback_t cb_done,
+				    struct net *net, int *pos, void *p);
 int sctp_for_each_endpoint(int (*cb)(struct sctp_endpoint *, void *), void *p);
 int sctp_get_sctp_info(struct sock *sk, struct sctp_association *asoc,
 		       struct sctp_info *info);
@@ -510,8 +509,8 @@
 	return (net_hash_mix(net) + lport) & (sctp_ep_hashsize - 1);
 }
 
-#define sctp_for_each_hentry(epb, head) \
-	hlist_for_each_entry(epb, head, node)
+#define sctp_for_each_hentry(ep, head) \
+	hlist_for_each_entry(ep, head, node)
 
 /* Is a socket of this style? */
 #define sctp_style(sk, style) __sctp_style((sk), (SCTP_SOCKET_##style))
@@ -626,7 +625,8 @@
 
 static inline int sctp_transport_pl_hlen(struct sctp_transport *t)
 {
-	return __sctp_mtu_payload(sctp_sk(t->asoc->base.sk), t, 0, 0);
+	return __sctp_mtu_payload(sctp_sk(t->asoc->base.sk), t, 0, 0) -
+	       sizeof(struct sctphdr);
 }
 
 static inline void sctp_transport_pl_reset(struct sctp_transport *t)
@@ -653,12 +653,10 @@
 	if (t->pl.state == SCTP_PL_DISABLED)
 		return;
 
-	if (del_timer(&t->probe_timer))
-		sctp_transport_put(t);
-
 	t->pl.state = SCTP_PL_BASE;
 	t->pl.pmtu = SCTP_BASE_PLPMTU;
 	t->pl.probe_size = SCTP_BASE_PLPMTU;
+	sctp_transport_reset_probe_timer(t);
 }
 
 static inline bool sctp_transport_pl_enabled(struct sctp_transport *t)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/sctp/stream_sched.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/sctp/stream_sched.h
@@ -26,6 +26,8 @@
 	int (*init)(struct sctp_stream *stream);
 	/* Init a stream */
 	int (*init_sid)(struct sctp_stream *stream, __u16 sid, gfp_t gfp);
+	/* free a stream */
+	void (*free_sid)(struct sctp_stream *stream, __u16 sid);
 	/* Frees the entire thing */
 	void (*free)(struct sctp_stream *stream);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/sctp/structs.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/sctp/structs.h
@@ -1244,10 +1244,6 @@
  */
 
 struct sctp_ep_common {
-	/* Fields to help us manage our entries in the hash tables. */
-	struct hlist_node node;
-	int hashent;
-
 	/* Runtime type information.  What kind of endpoint is this? */
 	enum sctp_endpoint_type type;
 
@@ -1299,6 +1295,10 @@
 	/* Common substructure for endpoint and association. */
 	struct sctp_ep_common base;
 
+	/* Fields to help us manage our entries in the hash tables. */
+	struct hlist_node node;
+	int hashent;
+
 	/* Associations: A list of current associations and mappings
 	 *	      to the data consumers for each association. This
 	 *	      may be in the form of a hash table or other
@@ -1365,6 +1365,7 @@
 
 	u32 secid;
 	u32 peer_secid;
+	struct rcu_head rcu;
 };
 
 /* Recover the outter endpoint structure. */
@@ -1380,7 +1381,7 @@
 struct sctp_endpoint *sctp_endpoint_new(struct sock *, gfp_t);
 void sctp_endpoint_free(struct sctp_endpoint *);
 void sctp_endpoint_put(struct sctp_endpoint *);
-void sctp_endpoint_hold(struct sctp_endpoint *);
+int sctp_endpoint_hold(struct sctp_endpoint *ep);
 void sctp_endpoint_add_asoc(struct sctp_endpoint *, struct sctp_association *);
 struct sctp_association *sctp_endpoint_lookup_assoc(
 	const struct sctp_endpoint *ep,
@@ -1419,6 +1420,7 @@
 	/* The next stream in line */
 	struct sctp_stream_out_ext *next;
 	__u16 prio;
+	__u16 users;
 };
 
 struct sctp_stream_out_ext {
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/secure_seq.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/secure_seq.h
@@ -4,8 +4,8 @@
 
 #include <linux/types.h>
 
-u32 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport);
-u32 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr,
+u64 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport);
+u64 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr,
 			       __be16 dport);
 u32 secure_tcp_seq(__be32 saddr, __be32 daddr,
 		   __be16 sport, __be16 dport);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/seg6.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/seg6.h
@@ -58,9 +58,30 @@
 extern void seg6_local_exit(void);
 
 extern bool seg6_validate_srh(struct ipv6_sr_hdr *srh, int len, bool reduced);
+extern struct ipv6_sr_hdr *seg6_get_srh(struct sk_buff *skb, int flags);
+extern void seg6_icmp_srh(struct sk_buff *skb, struct inet6_skb_parm *opt);
 extern int seg6_do_srh_encap(struct sk_buff *skb, struct ipv6_sr_hdr *osrh,
 			     int proto);
 extern int seg6_do_srh_inline(struct sk_buff *skb, struct ipv6_sr_hdr *osrh);
 extern int seg6_lookup_nexthop(struct sk_buff *skb, struct in6_addr *nhaddr,
 			       u32 tbl_id);
+
+/* If the packet which invoked an ICMP error contains an SRH return
+ * the true destination address from within the SRH, otherwise use the
+ * destination address in the IP header.
+ */
+static inline const struct in6_addr *seg6_get_daddr(struct sk_buff *skb,
+						    struct inet6_skb_parm *opt)
+{
+	struct ipv6_sr_hdr *srh;
+
+	if (opt->flags & IP6SKB_SEG6) {
+		srh = (struct ipv6_sr_hdr *)(skb->data + opt->srhoff);
+		return  &srh->segments[0];
+	}
+
+	return NULL;
+}
+
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/sock.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/sock.h
@@ -161,9 +161,6 @@
  *	for struct sock and struct inet_timewait_sock.
  */
 struct sock_common {
-	/* skc_daddr and skc_rcv_saddr must be grouped on a 8 bytes aligned
-	 * address on 64bit arches : cf INET_MATCH()
-	 */
 	union {
 		__addrpair	skc_addrpair;
 		struct {
@@ -259,6 +256,8 @@
   *	@sk_rcvbuf: size of receive buffer in bytes
   *	@sk_wq: sock wait queue and async head
   *	@sk_rx_dst: receive input route used by early demux
+  *	@sk_rx_dst_ifindex: ifindex for @sk_rx_dst
+  *	@sk_rx_dst_cookie: cookie for @sk_rx_dst
   *	@sk_dst_cache: destination cache
   *	@sk_dst_pending_confirm: need to confirm neighbour
   *	@sk_policy: flow policy
@@ -324,7 +323,7 @@
   *	@sk_tskey: counter to disambiguate concurrent tstamp requests
   *	@sk_zckey: counter to order MSG_ZEROCOPY notifications
   *	@sk_socket: Identd and reporting IO signals
-  *	@sk_user_data: RPC layer private data
+  *	@sk_user_data: RPC layer private data. Write-protected by @sk_callback_lock.
   *	@sk_frag: cached page frag
   *	@sk_peek_off: current peek_offset value
   *	@sk_send_head: front of stuff to transmit
@@ -335,6 +334,7 @@
   *	@sk_cgrp_data: cgroup data for this cgroup
   *	@sk_memcg: this socket's memory cgroup association
   *	@sk_write_pending: a write to stream socket waits to start
+  *	@sk_wait_pending: number of threads blocked on this socket
   *	@sk_state_change: callback to indicate change in the state of the sock
   *	@sk_data_ready: callback to indicate there is data to be processed
   *	@sk_write_space: callback to indicate there is bf sending space available
@@ -419,6 +419,7 @@
 	unsigned int		sk_napi_id;
 #endif
 	int			sk_rcvbuf;
+	int			sk_wait_pending;
 
 	struct sk_filter __rcu	*sk_filter;
 	union {
@@ -430,7 +431,10 @@
 #ifdef CONFIG_XFRM
 	struct xfrm_policy __rcu *sk_policy[2];
 #endif
-	struct dst_entry	*sk_rx_dst;
+	struct dst_entry __rcu	*sk_rx_dst;
+	int			sk_rx_dst_ifindex;
+	u32			sk_rx_dst_cookie;
+
 	struct dst_entry __rcu	*sk_dst_cache;
 	atomic_t		sk_omem_alloc;
 	int			sk_sndbuf;
@@ -501,7 +505,7 @@
 	u16			sk_tsflags;
 	int			sk_bind_phc;
 	u8			sk_shutdown;
-	u32			sk_tskey;
+	atomic_t		sk_tskey;
 	atomic_t		sk_zckey;
 
 	u8			sk_clockid;
@@ -541,14 +545,26 @@
 	SK_PACING_FQ		= 2,
 };
 
-/* Pointer stored in sk_user_data might not be suitable for copying
- * when cloning the socket. For instance, it can point to a reference
- * counted object. sk_user_data bottom bit is set if pointer must not
- * be copied.
+/* flag bits in sk_user_data
+ *
+ * - SK_USER_DATA_NOCOPY:      Pointer stored in sk_user_data might
+ *   not be suitable for copying when cloning the socket. For instance,
+ *   it can point to a reference counted object. sk_user_data bottom
+ *   bit is set if pointer must not be copied.
+ *
+ * - SK_USER_DATA_BPF:         Mark whether sk_user_data field is
+ *   managed/owned by a BPF reuseport array. This bit should be set
+ *   when sk_user_data's sk is added to the bpf's reuseport_array.
+ *
+ * - SK_USER_DATA_PSOCK:       Mark whether pointer stored in
+ *   sk_user_data points to psock type. This bit should be set
+ *   when sk_user_data is assigned to a psock object.
  */
 #define SK_USER_DATA_NOCOPY	1UL
-#define SK_USER_DATA_BPF	2UL	/* Managed by BPF */
-#define SK_USER_DATA_PTRMASK	~(SK_USER_DATA_NOCOPY | SK_USER_DATA_BPF)
+#define SK_USER_DATA_BPF	2UL
+#define SK_USER_DATA_PSOCK	4UL
+#define SK_USER_DATA_PTRMASK	~(SK_USER_DATA_NOCOPY | SK_USER_DATA_BPF |\
+				  SK_USER_DATA_PSOCK)
 
 /**
  * sk_user_data_is_nocopy - Test if sk_user_data pointer must not be copied
@@ -561,24 +577,40 @@
 
 #define __sk_user_data(sk) ((*((void __rcu **)&(sk)->sk_user_data)))
 
+/**
+ * __rcu_dereference_sk_user_data_with_flags - return the pointer
+ * only if argument flags all has been set in sk_user_data. Otherwise
+ * return NULL
+ *
+ * @sk: socket
+ * @flags: flag bits
+ */
+static inline void *
+__rcu_dereference_sk_user_data_with_flags(const struct sock *sk,
+					  uintptr_t flags)
+{
+	uintptr_t sk_user_data = (uintptr_t)rcu_dereference(__sk_user_data(sk));
+
+	WARN_ON_ONCE(flags & SK_USER_DATA_PTRMASK);
+
+	if ((sk_user_data & flags) == flags)
+		return (void *)(sk_user_data & SK_USER_DATA_PTRMASK);
+	return NULL;
+}
+
 #define rcu_dereference_sk_user_data(sk)				\
+	__rcu_dereference_sk_user_data_with_flags(sk, 0)
+#define __rcu_assign_sk_user_data_with_flags(sk, ptr, flags)		\
 ({									\
-	void *__tmp = rcu_dereference(__sk_user_data((sk)));		\
-	(void *)((uintptr_t)__tmp & SK_USER_DATA_PTRMASK);		\
-})
-#define rcu_assign_sk_user_data(sk, ptr)				\
-({									\
-	uintptr_t __tmp = (uintptr_t)(ptr);				\
-	WARN_ON_ONCE(__tmp & ~SK_USER_DATA_PTRMASK);			\
-	rcu_assign_pointer(__sk_user_data((sk)), __tmp);		\
-})
-#define rcu_assign_sk_user_data_nocopy(sk, ptr)				\
-({									\
-	uintptr_t __tmp = (uintptr_t)(ptr);				\
-	WARN_ON_ONCE(__tmp & ~SK_USER_DATA_PTRMASK);			\
+	uintptr_t __tmp1 = (uintptr_t)(ptr),				\
+		  __tmp2 = (uintptr_t)(flags);				\
+	WARN_ON_ONCE(__tmp1 & ~SK_USER_DATA_PTRMASK);			\
+	WARN_ON_ONCE(__tmp2 & SK_USER_DATA_PTRMASK);			\
 	rcu_assign_pointer(__sk_user_data((sk)),			\
-			   __tmp | SK_USER_DATA_NOCOPY);		\
+			   __tmp1 | __tmp2);				\
 })
+#define rcu_assign_sk_user_data(sk, ptr)				\
+	__rcu_assign_sk_user_data_with_flags(sk, ptr, 0)
 
 /*
  * SK_CAN_REUSE and SK_NO_REUSE on a socket mean that the socket is OK
@@ -818,6 +850,8 @@
 	hlist_for_each_entry_safe(__sk, tmp, list, sk_node)
 #define sk_for_each_bound(__sk, list) \
 	hlist_for_each_entry(__sk, list, sk_bind_node)
+#define sk_for_each_bound_safe(__sk, tmp, list) \
+	hlist_for_each_entry_safe(__sk, tmp, list, sk_bind_node)
 
 /**
  * sk_for_each_entry_offset_rcu - iterate over a list at a given struct offset
@@ -1061,8 +1095,12 @@
 		 * OR	an additional socket flag
 		 * [1] : sk_state and sk_prot are in the same cache line.
 		 */
-		if (sk->sk_state == TCP_ESTABLISHED)
-			sock_rps_record_flow_hash(sk->sk_rxhash);
+		if (sk->sk_state == TCP_ESTABLISHED) {
+			/* This READ_ONCE() is paired with the WRITE_ONCE()
+			 * from sock_rps_save_rxhash() and sock_rps_reset_rxhash().
+			 */
+			sock_rps_record_flow_hash(READ_ONCE(sk->sk_rxhash));
+		}
 	}
 #endif
 }
@@ -1071,20 +1109,25 @@
 					const struct sk_buff *skb)
 {
 #ifdef CONFIG_RPS
-	if (unlikely(sk->sk_rxhash != skb->hash))
-		sk->sk_rxhash = skb->hash;
+	/* The following WRITE_ONCE() is paired with the READ_ONCE()
+	 * here, and another one in sock_rps_record_flow().
+	 */
+	if (unlikely(READ_ONCE(sk->sk_rxhash) != skb->hash))
+		WRITE_ONCE(sk->sk_rxhash, skb->hash);
 #endif
 }
 
 static inline void sock_rps_reset_rxhash(struct sock *sk)
 {
 #ifdef CONFIG_RPS
-	sk->sk_rxhash = 0;
+	/* Paired with READ_ONCE() in sock_rps_record_flow() */
+	WRITE_ONCE(sk->sk_rxhash, 0);
 #endif
 }
 
 #define sk_wait_event(__sk, __timeo, __condition, __wait)		\
 	({	int __rc;						\
+		__sk->sk_wait_pending++;				\
 		release_sock(__sk);					\
 		__rc = __condition;					\
 		if (!__rc) {						\
@@ -1094,6 +1137,7 @@
 		}							\
 		sched_annotate_sleep();					\
 		lock_sock(__sk);					\
+		__sk->sk_wait_pending--;				\
 		__rc = __condition;					\
 		__rc;							\
 	})
@@ -1217,6 +1261,7 @@
 	/*
 	 * Pressure flag: try to collapse.
 	 * Technical note: it is used by multiple contexts non atomically.
+	 * Make sure to use READ_ONCE()/WRITE_ONCE() for all reads/writes.
 	 * All the __sk_mem_schedule() is of this nature: accounting
 	 * is strict, actions are advisory and have some latency.
 	 */
@@ -1237,7 +1282,7 @@
 	unsigned int		useroffset;	/* Usercopy region offset */
 	unsigned int		usersize;	/* Usercopy region size */
 
-	struct percpu_counter	*orphan_count;
+	unsigned int __percpu	*orphan_count;
 
 	struct request_sock_ops	*rsk_prot;
 	struct timewait_sock_ops *twsk_prot;
@@ -1339,6 +1384,12 @@
 	return sk->sk_prot->memory_pressure != NULL;
 }
 
+static inline bool sk_under_global_memory_pressure(const struct sock *sk)
+{
+	return sk->sk_prot->memory_pressure &&
+		!!READ_ONCE(*sk->sk_prot->memory_pressure);
+}
+
 static inline bool sk_under_memory_pressure(const struct sock *sk)
 {
 	if (!sk->sk_prot->memory_pressure)
@@ -1348,7 +1399,7 @@
 	    mem_cgroup_under_socket_pressure(sk->sk_memcg))
 		return true;
 
-	return !!*sk->sk_prot->memory_pressure;
+	return !!READ_ONCE(*sk->sk_prot->memory_pressure);
 }
 
 static inline long
@@ -1406,18 +1457,36 @@
 {
 	if (!prot->memory_pressure)
 		return false;
-	return !!*prot->memory_pressure;
+	return !!READ_ONCE(*prot->memory_pressure);
 }
 
 
 #ifdef CONFIG_PROC_FS
-/* Called with local bh disabled */
-void sock_prot_inuse_add(struct net *net, struct proto *prot, int inc);
+#define PROTO_INUSE_NR	64	/* should be enough for the first time */
+struct prot_inuse {
+	int val[PROTO_INUSE_NR];
+};
+
+static inline void sock_prot_inuse_add(const struct net *net,
+				       const struct proto *prot, int val)
+{
+	this_cpu_add(net->core.prot_inuse->val[prot->inuse_idx], val);
+}
+
+static inline void sock_inuse_add(const struct net *net, int val)
+{
+	this_cpu_add(*net->core.sock_inuse, val);
+}
+
 int sock_prot_inuse_get(struct net *net, struct proto *proto);
 int sock_inuse_get(struct net *net);
 #else
-static inline void sock_prot_inuse_add(struct net *net, struct proto *prot,
-		int inc)
+static inline void sock_prot_inuse_add(const struct net *net,
+				       const struct proto *prot, int val)
+{
+}
+
+static inline void sock_inuse_add(const struct net *net, int val)
 {
 }
 #endif
@@ -1479,7 +1548,7 @@
 /* sysctl_mem values are in pages, we convert them in SK_MEM_QUANTUM units */
 static inline long sk_prot_mem_limits(const struct sock *sk, int index)
 {
-	long val = sk->sk_prot->sysctl_mem[index];
+	long val = READ_ONCE(sk->sk_prot->sysctl_mem[index]);
 
 #if PAGE_SIZE > SK_MEM_QUANTUM
 	val <<= PAGE_SHIFT - SK_MEM_QUANTUM_SHIFT;
@@ -1502,20 +1571,30 @@
 
 static inline bool sk_wmem_schedule(struct sock *sk, int size)
 {
+	int delta;
+
 	if (!sk_has_account(sk))
 		return true;
-	return size <= sk->sk_forward_alloc ||
-		__sk_mem_schedule(sk, size, SK_MEM_SEND);
+	delta = size - sk->sk_forward_alloc;
+	return delta <= 0 || __sk_mem_schedule(sk, delta, SK_MEM_SEND);
 }
 
 static inline bool
-sk_rmem_schedule(struct sock *sk, struct sk_buff *skb, int size)
+__sk_rmem_schedule(struct sock *sk, int size, bool pfmemalloc)
 {
+	int delta;
+
 	if (!sk_has_account(sk))
 		return true;
-	return size <= sk->sk_forward_alloc ||
-		__sk_mem_schedule(sk, size, SK_MEM_RECV) ||
-		skb_pfmemalloc(skb);
+	delta = size - sk->sk_forward_alloc;
+	return delta <= 0 || __sk_mem_schedule(sk, delta, SK_MEM_RECV) ||
+	       pfmemalloc;
+}
+
+static inline bool
+sk_rmem_schedule(struct sock *sk, struct sk_buff *skb, int size)
+{
+	return __sk_rmem_schedule(sk, size, skb_pfmemalloc(skb));
 }
 
 static inline void sk_mem_reclaim(struct sock *sk)
@@ -1698,6 +1777,13 @@
 #endif
 }
 
+static inline void sock_not_owned_by_me(const struct sock *sk)
+{
+#ifdef CONFIG_LOCKDEP
+	WARN_ON_ONCE(lockdep_sock_is_held(sk) && debug_locks);
+#endif
+}
+
 static inline bool sock_owned_by_user(const struct sock *sk)
 {
 	sock_owned_by_me(sk);
@@ -1813,7 +1899,12 @@
  *	Default socket callbacks and setup code
  */
 
-/* Initialise core socket variables */
+/* Initialise core socket variables using an explicit uid. */
+void sock_init_data_uid(struct socket *sock, struct sock *sk, kuid_t uid);
+
+/* Initialise core socket variables.
+ * Assumes struct socket *sock is embedded in a struct socket_alloc.
+ */
 void sock_init_data(struct socket *sock, struct sock *sk);
 
 /*
@@ -1865,21 +1956,33 @@
 	/* sk_tx_queue_mapping accept only upto a 16-bit value */
 	if (WARN_ON_ONCE((unsigned short)tx_queue >= USHRT_MAX))
 		return;
-	sk->sk_tx_queue_mapping = tx_queue;
+	/* Paired with READ_ONCE() in sk_tx_queue_get() and
+	 * other WRITE_ONCE() because socket lock might be not held.
+	 */
+	WRITE_ONCE(sk->sk_tx_queue_mapping, tx_queue);
 }
 
 #define NO_QUEUE_MAPPING	USHRT_MAX
 
 static inline void sk_tx_queue_clear(struct sock *sk)
 {
-	sk->sk_tx_queue_mapping = NO_QUEUE_MAPPING;
+	/* Paired with READ_ONCE() in sk_tx_queue_get() and
+	 * other WRITE_ONCE() because socket lock might be not held.
+	 */
+	WRITE_ONCE(sk->sk_tx_queue_mapping, NO_QUEUE_MAPPING);
 }
 
 static inline int sk_tx_queue_get(const struct sock *sk)
 {
-	if (sk && sk->sk_tx_queue_mapping != NO_QUEUE_MAPPING)
-		return sk->sk_tx_queue_mapping;
+	if (sk) {
+		/* Paired with WRITE_ONCE() in sk_tx_queue_clear()
+		 * and sk_tx_queue_set().
+		 */
+		int val = READ_ONCE(sk->sk_tx_queue_mapping);
 
+		if (val != NO_QUEUE_MAPPING)
+			return val;
+	}
 	return -1;
 }
 
@@ -1953,6 +2056,7 @@
 }
 
 kuid_t sock_i_uid(struct sock *sk);
+unsigned long __sock_i_ino(struct sock *sk);
 unsigned long sock_i_ino(struct sock *sk);
 
 static inline kuid_t sock_net_uid(const struct net *net, const struct sock *sk)
@@ -2004,17 +2108,10 @@
 
 static inline void __dst_negative_advice(struct sock *sk)
 {
-	struct dst_entry *ndst, *dst = __sk_dst_get(sk);
+	struct dst_entry *dst = __sk_dst_get(sk);
 
-	if (dst && dst->ops->negative_advice) {
-		ndst = dst->ops->negative_advice(dst);
-
-		if (ndst != dst) {
-			rcu_assign_pointer(sk->sk_dst_cache, ndst);
-			sk_tx_queue_clear(sk);
-			sk->sk_dst_pending_confirm = 0;
-		}
-	}
+	if (dst && dst->ops->negative_advice)
+		dst->ops->negative_advice(sk, dst);
 }
 
 static inline void dst_negative_advice(struct sock *sk)
@@ -2029,7 +2126,7 @@
 	struct dst_entry *old_dst;
 
 	sk_tx_queue_clear(sk);
-	sk->sk_dst_pending_confirm = 0;
+	WRITE_ONCE(sk->sk_dst_pending_confirm, 0);
 	old_dst = rcu_dereference_protected(sk->sk_dst_cache,
 					    lockdep_sock_is_held(sk));
 	rcu_assign_pointer(sk->sk_dst_cache, dst);
@@ -2042,7 +2139,7 @@
 	struct dst_entry *old_dst;
 
 	sk_tx_queue_clear(sk);
-	sk->sk_dst_pending_confirm = 0;
+	WRITE_ONCE(sk->sk_dst_pending_confirm, 0);
 	old_dst = xchg((__force struct dst_entry **)&sk->sk_dst_cache, dst);
 	dst_release(old_dst);
 }
@@ -2281,6 +2378,19 @@
 	return false;
 }
 
+static inline struct sk_buff *skb_clone_and_charge_r(struct sk_buff *skb, struct sock *sk)
+{
+	skb = skb_clone(skb, sk_gfp_mask(sk, GFP_ATOMIC));
+	if (skb) {
+		if (sk_rmem_schedule(sk, skb, skb->truesize)) {
+			skb_set_owner_r(skb, sk);
+			return skb;
+		}
+		__kfree_skb(skb);
+	}
+	return NULL;
+}
+
 static inline void skb_prepare_for_gro(struct sk_buff *skb)
 {
 	if (skb->destructor != sock_wfree) {
@@ -2400,19 +2510,22 @@
  * @sk: socket
  *
  * Use the per task page_frag instead of the per socket one for
- * optimization when we know that we're in the normal context and owns
+ * optimization when we know that we're in process context and own
  * everything that's associated with %current.
  *
- * gfpflags_allow_blocking() isn't enough here as direct reclaim may nest
- * inside other socket operations and end up recursing into sk_page_frag()
- * while it's already in use.
+ * Both direct reclaim and page faults can nest inside other
+ * socket operations and end up recursing into sk_page_frag()
+ * while it's already in use: explicitly avoid task page_frag
+ * usage if the caller is potentially doing any of them.
+ * This assumes that page fault handlers use the GFP_NOFS flags.
  *
  * Return: a per task page_frag if context allows that,
  * otherwise a per socket one.
  */
 static inline struct page_frag *sk_page_frag(struct sock *sk)
 {
-	if (gfpflags_normal_context(sk->sk_allocation))
+	if ((sk->sk_allocation & (__GFP_DIRECT_RECLAIM | __GFP_MEMALLOC | __GFP_FS)) ==
+	    (__GFP_DIRECT_RECLAIM | __GFP_FS))
 		return &current->task_frag;
 
 	return &sk->sk_frag;
@@ -2435,7 +2548,7 @@
 
 static inline gfp_t gfp_memcg_charge(void)
 {
-	return in_softirq() ? GFP_NOWAIT : GFP_KERNEL;
+	return in_softirq() ? GFP_ATOMIC : GFP_KERNEL;
 }
 
 static inline long sock_rcvtimeo(const struct sock *sk, bool noblock)
@@ -2568,7 +2681,7 @@
 		__sock_recv_ts_and_drops(msg, sk, skb);
 	else if (unlikely(sock_flag(sk, SOCK_TIMESTAMP)))
 		sock_write_timestamp(sk, skb->tstamp);
-	else if (unlikely(sk->sk_stamp == SK_DEFAULT_STAMP))
+	else if (unlikely(sock_read_timestamp(sk) == SK_DEFAULT_STAMP))
 		sock_write_timestamp(sk, 0);
 }
 
@@ -2590,7 +2703,7 @@
 		__sock_tx_timestamp(tsflags, tx_flags);
 		if (tsflags & SOF_TIMESTAMPING_OPT_ID && tskey &&
 		    tsflags & SOF_TIMESTAMPING_TX_RECORD_MASK)
-			*tskey = sk->sk_tskey++;
+			*tskey = atomic_inc_return(&sk->sk_tskey) - 1;
 	}
 	if (unlikely(sock_flag(sk, SOCK_WIFI_STATUS)))
 		*tx_flags |= SKBTX_WIFI_STATUS;
@@ -2757,18 +2870,18 @@
 {
 	/* Does this proto have per netns sysctl_wmem ? */
 	if (proto->sysctl_wmem_offset)
-		return *(int *)((void *)sock_net(sk) + proto->sysctl_wmem_offset);
+		return READ_ONCE(*(int *)((void *)sock_net(sk) + proto->sysctl_wmem_offset));
 
-	return *proto->sysctl_wmem;
+	return READ_ONCE(*proto->sysctl_wmem);
 }
 
 static inline int sk_get_rmem0(const struct sock *sk, const struct proto *proto)
 {
 	/* Does this proto have per netns sysctl_rmem ? */
 	if (proto->sysctl_rmem_offset)
-		return *(int *)((void *)sock_net(sk) + proto->sysctl_rmem_offset);
+		return READ_ONCE(*(int *)((void *)sock_net(sk) + proto->sysctl_rmem_offset));
 
-	return *proto->sysctl_rmem;
+	return READ_ONCE(*proto->sysctl_rmem);
 }
 
 /* Default TCP Small queue budget is ~1 ms of data (1sec >> 10)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/sock_reuseport.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/sock_reuseport.h
@@ -16,6 +16,7 @@
 	u16			max_socks;		/* length of socks */
 	u16			num_socks;		/* elements in socks */
 	u16			num_closed_socks;	/* closed elements in socks */
+	u16			incoming_cpu;
 	/* The last synq overflow event timestamp of this
 	 * reuse->socks[] group.
 	 */
@@ -43,21 +44,21 @@
 extern int reuseport_attach_prog(struct sock *sk, struct bpf_prog *prog);
 extern int reuseport_detach_prog(struct sock *sk);
 
-static inline bool reuseport_has_conns(struct sock *sk, bool set)
+static inline bool reuseport_has_conns(struct sock *sk)
 {
 	struct sock_reuseport *reuse;
 	bool ret = false;
 
 	rcu_read_lock();
 	reuse = rcu_dereference(sk->sk_reuseport_cb);
-	if (reuse) {
-		if (set)
-			reuse->has_conns = 1;
-		ret = reuse->has_conns;
-	}
+	if (reuse && reuse->has_conns)
+		ret = true;
 	rcu_read_unlock();
 
 	return ret;
 }
 
+void reuseport_has_conns_set(struct sock *sk);
+void reuseport_update_incoming_cpu(struct sock *sk, int val);
+
 #endif  /* _SOCK_REUSEPORT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/strparser.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/strparser.h
@@ -54,10 +54,32 @@
 	int offset;
 };
 
+struct _strp_msg {
+	/* Internal cb structure. struct strp_msg must be first for passing
+	 * to upper layer.
+	 */
+	struct strp_msg strp;
+	int accum_len;
+};
+
+struct sk_skb_cb {
+#define SK_SKB_CB_PRIV_LEN 20
+	unsigned char data[SK_SKB_CB_PRIV_LEN];
+	struct _strp_msg strp;
+	/* temp_reg is a temporary register used for bpf_convert_data_end_access
+	 * when dst_reg == src_reg.
+	 */
+	u64 temp_reg;
+	struct tls_msg {
+		u8 control;
+		u8 decrypted;
+	} tls;
+};
+
 static inline struct strp_msg *strp_msg(struct sk_buff *skb)
 {
 	return (struct strp_msg *)((void *)skb->cb +
-		offsetof(struct qdisc_skb_cb, data));
+		offsetof(struct sk_skb_cb, strp));
 }
 
 /* Structure for an attached lower socket */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/switchdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/switchdev.h
@@ -277,6 +277,9 @@
 int switchdev_port_attr_set(struct net_device *dev,
 			    const struct switchdev_attr *attr,
 			    struct netlink_ext_ack *extack);
+bool switchdev_port_obj_act_is_deferred(struct net_device *dev,
+					enum switchdev_notifier_type nt,
+					const struct switchdev_obj *obj);
 int switchdev_port_obj_add(struct net_device *dev,
 			   const struct switchdev_obj *obj,
 			   struct netlink_ext_ack *extack);
@@ -373,6 +376,13 @@
 	return -EOPNOTSUPP;
 }
 
+static bool switchdev_port_obj_act_is_deferred(struct net_device *dev,
+					       enum switchdev_notifier_type nt,
+					       const struct switchdev_obj *obj)
+{
+	return false;
+}
+
 static inline int switchdev_port_obj_add(struct net_device *dev,
 					 const struct switchdev_obj *obj,
 					 struct netlink_ext_ack *extack)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/tc_act/tc_pedit.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/tc_act/tc_pedit.h
@@ -4,21 +4,29 @@
 
 #include <net/act_api.h>
 #include <linux/tc_act/tc_pedit.h>
+#include <linux/types.h>
 
 struct tcf_pedit_key_ex {
 	enum pedit_header_type htype;
 	enum pedit_cmd cmd;
 };
 
-struct tcf_pedit {
-	struct tc_action	common;
-	unsigned char		tcfp_nkeys;
-	unsigned char		tcfp_flags;
+struct tcf_pedit_parms {
 	struct tc_pedit_key	*tcfp_keys;
 	struct tcf_pedit_key_ex	*tcfp_keys_ex;
+	u32 tcfp_off_max_hint;
+	unsigned char tcfp_nkeys;
+	unsigned char tcfp_flags;
+	struct rcu_head rcu;
+};
+
+struct tcf_pedit {
+	struct tc_action common;
+	struct tcf_pedit_parms __rcu *parms;
 };
 
 #define to_pedit(a) ((struct tcf_pedit *)a)
+#define to_pedit_parms(a) (rcu_dereference(to_pedit(a)->parms))
 
 static inline bool is_tcf_pedit(const struct tc_action *a)
 {
@@ -31,37 +39,81 @@
 
 static inline int tcf_pedit_nkeys(const struct tc_action *a)
 {
-	return to_pedit(a)->tcfp_nkeys;
+	struct tcf_pedit_parms *parms;
+	int nkeys;
+
+	rcu_read_lock();
+	parms = to_pedit_parms(a);
+	nkeys = parms->tcfp_nkeys;
+	rcu_read_unlock();
+
+	return nkeys;
 }
 
 static inline u32 tcf_pedit_htype(const struct tc_action *a, int index)
 {
-	if (to_pedit(a)->tcfp_keys_ex)
-		return to_pedit(a)->tcfp_keys_ex[index].htype;
+	u32 htype = TCA_PEDIT_KEY_EX_HDR_TYPE_NETWORK;
+	struct tcf_pedit_parms *parms;
+
+	rcu_read_lock();
+	parms = to_pedit_parms(a);
+	if (parms->tcfp_keys_ex)
+		htype = parms->tcfp_keys_ex[index].htype;
+	rcu_read_unlock();
 
-	return TCA_PEDIT_KEY_EX_HDR_TYPE_NETWORK;
+	return htype;
 }
 
 static inline u32 tcf_pedit_cmd(const struct tc_action *a, int index)
 {
-	if (to_pedit(a)->tcfp_keys_ex)
-		return to_pedit(a)->tcfp_keys_ex[index].cmd;
+	struct tcf_pedit_parms *parms;
+	u32 cmd = __PEDIT_CMD_MAX;
 
-	return __PEDIT_CMD_MAX;
+	rcu_read_lock();
+	parms = to_pedit_parms(a);
+	if (parms->tcfp_keys_ex)
+		cmd = parms->tcfp_keys_ex[index].cmd;
+	rcu_read_unlock();
+
+	return cmd;
 }
 
 static inline u32 tcf_pedit_mask(const struct tc_action *a, int index)
 {
-	return to_pedit(a)->tcfp_keys[index].mask;
+	struct tcf_pedit_parms *parms;
+	u32 mask;
+
+	rcu_read_lock();
+	parms = to_pedit_parms(a);
+	mask = parms->tcfp_keys[index].mask;
+	rcu_read_unlock();
+
+	return mask;
 }
 
 static inline u32 tcf_pedit_val(const struct tc_action *a, int index)
 {
-	return to_pedit(a)->tcfp_keys[index].val;
+	struct tcf_pedit_parms *parms;
+	u32 val;
+
+	rcu_read_lock();
+	parms = to_pedit_parms(a);
+	val = parms->tcfp_keys[index].val;
+	rcu_read_unlock();
+
+	return val;
 }
 
 static inline u32 tcf_pedit_offset(const struct tc_action *a, int index)
 {
-	return to_pedit(a)->tcfp_keys[index].off;
+	struct tcf_pedit_parms *parms;
+	u32 off;
+
+	rcu_read_lock();
+	parms = to_pedit_parms(a);
+	off = parms->tcfp_keys[index].off;
+	rcu_read_unlock();
+
+	return off;
 }
 #endif /* __NET_TC_PED_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/tcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/tcp.h
@@ -48,7 +48,9 @@
 
 extern struct inet_hashinfo tcp_hashinfo;
 
-extern struct percpu_counter tcp_orphan_count;
+DECLARE_PER_CPU(unsigned int, tcp_orphan_count);
+int tcp_orphan_count_sum(void);
+
 void tcp_time_wait(struct sock *sk, int state, int timeo);
 
 #define MAX_TCP_HEADER	L1_CACHE_ALIGN(128 + MAX_HEADER)
@@ -139,6 +141,9 @@
 #define TCP_RTO_MAX	((unsigned)(120*HZ))
 #define TCP_RTO_MIN	((unsigned)(HZ/5))
 #define TCP_TIMEOUT_MIN	(2U) /* Min timeout for TCP timers in jiffies */
+
+#define TCP_TIMEOUT_MIN_US (2*USEC_PER_MSEC) /* Min TCP timeout in microsecs */
+
 #define TCP_TIMEOUT_INIT ((unsigned)(1*HZ))	/* RFC6298 2.1 initial RTO value	*/
 #define TCP_TIMEOUT_FALLBACK ((unsigned)(3*HZ))	/* RFC 1122 initial RTO value, now
 						 * used as a fallback RTO for the
@@ -290,19 +295,6 @@
 
 void sk_forced_mem_schedule(struct sock *sk, int size);
 
-static inline bool tcp_too_many_orphans(struct sock *sk, int shift)
-{
-	struct percpu_counter *ocp = sk->sk_prot->orphan_count;
-	int orphans = percpu_counter_read_positive(ocp);
-
-	if (orphans << shift > sysctl_tcp_max_orphans) {
-		orphans = percpu_counter_sum_positive(ocp);
-		if (orphans << shift > sysctl_tcp_max_orphans)
-			return true;
-	}
-	return false;
-}
-
 bool tcp_check_oom(struct sock *sk, int shift);
 
 
@@ -322,7 +314,7 @@
 int tcp_v4_early_demux(struct sk_buff *skb);
 int tcp_v4_rcv(struct sk_buff *skb);
 
-void tcp_remove_empty_skb(struct sock *sk, struct sk_buff *skb);
+void tcp_remove_empty_skb(struct sock *sk);
 int tcp_v4_tw_remember_stamp(struct inet_timewait_sock *tw);
 int tcp_sendmsg(struct sock *sk, struct msghdr *msg, size_t size);
 int tcp_sendmsg_locked(struct sock *sk, struct msghdr *msg, size_t size);
@@ -351,13 +343,14 @@
 			struct pipe_inode_info *pipe, size_t len,
 			unsigned int flags);
 
-void tcp_enter_quickack_mode(struct sock *sk, unsigned int max_quickacks);
-static inline void tcp_dec_quickack_mode(struct sock *sk,
-					 const unsigned int pkts)
+static inline void tcp_dec_quickack_mode(struct sock *sk)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 
 	if (icsk->icsk_ack.quick) {
+		/* How many ACKs S/ACKing new data have we sent? */
+		const unsigned int pkts = inet_csk_ack_scheduled(sk) ? 1 : 0;
+
 		if (pkts >= icsk->icsk_ack.quick) {
 			icsk->icsk_ack.quick = 0;
 			/* Leaving quickack mode we deflate ATO. */
@@ -481,6 +474,7 @@
 		      u32 cookie);
 struct sock *cookie_v4_check(struct sock *sk, struct sk_buff *skb);
 struct request_sock *cookie_tcp_reqsk_alloc(const struct request_sock_ops *ops,
+					    const struct tcp_request_sock_ops *af_ops,
 					    struct sock *sk, struct sk_buff *skb);
 #ifdef CONFIG_SYN_COOKIES
 
@@ -581,6 +575,8 @@
 #endif
 /* tcp_output.c */
 
+void tcp_skb_entail(struct sock *sk, struct sk_buff *skb);
+void tcp_mark_push(struct tcp_sock *tp, struct sk_buff *skb);
 void __tcp_push_pending_frames(struct sock *sk, unsigned int cur_mss,
 			       int nonagle);
 int __tcp_retransmit_skb(struct sock *sk, struct sk_buff *skb, int segs);
@@ -616,9 +612,11 @@
 /* tcp_input.c */
 void tcp_rearm_rto(struct sock *sk);
 void tcp_synack_rtt_meas(struct sock *sk, struct request_sock *req);
+void tcp_done_with_error(struct sock *sk, int err);
 void tcp_reset(struct sock *sk, struct sk_buff *skb);
 void tcp_skb_mark_lost_uncond_verify(struct tcp_sock *tp, struct sk_buff *skb);
 void tcp_fin(struct sock *sk);
+void tcp_check_space(struct sock *sk);
 
 /* tcp_timer.c */
 void tcp_init_xmit_timers(struct sock *);
@@ -789,7 +787,7 @@
 }
 
 /* Convert a nsec timestamp into TCP TSval timestamp (ms based currently) */
-static inline u32 tcp_ns_to_ts(u64 ns)
+static inline u64 tcp_ns_to_ts(u64 ns)
 {
 	return div_u64(ns, NSEC_PER_SEC / TCP_TS_HZ);
 }
@@ -928,7 +926,7 @@
 
 INDIRECT_CALLABLE_DECLARE(void tcp_v6_send_check(struct sock *sk, struct sk_buff *skb));
 INDIRECT_CALLABLE_DECLARE(int tcp_v6_rcv(struct sk_buff *skb));
-INDIRECT_CALLABLE_DECLARE(void tcp_v6_early_demux(struct sk_buff *skb));
+void tcp_v6_early_demux(struct sk_buff *skb);
 
 #endif
 
@@ -1037,6 +1035,7 @@
 	int  losses;		/* number of packets marked lost upon ACK */
 	u32  acked_sacked;	/* number of packets newly (S)ACKed upon ACK */
 	u32  prior_in_flight;	/* in flight before this ACK */
+	u32  last_end_seq;	/* end_seq of most recently ACKed packet */
 	bool is_app_limited;	/* is sample from packet with bubble in pipe? */
 	bool is_retrans;	/* is sample from retransmission? */
 	bool is_ack_delayed;	/* is this (likely) a delayed ACK? */
@@ -1159,6 +1158,11 @@
 		  bool is_sack_reneg, struct rate_sample *rs);
 void tcp_rate_check_app_limited(struct sock *sk);
 
+static inline bool tcp_skb_sent_after(u64 t1, u64 t2, u32 seq1, u32 seq2)
+{
+	return t1 > t2 || (t1 == t2 && after(seq1, seq2));
+}
+
 /* These functions determine how the current flow behaves in respect of SACK
  * handling. SACK is negotiated with the peer, and therefore it can vary
  * between different flows.
@@ -1202,9 +1206,20 @@
 
 #define TCP_INFINITE_SSTHRESH	0x7fffffff
 
+static inline u32 tcp_snd_cwnd(const struct tcp_sock *tp)
+{
+	return tp->snd_cwnd;
+}
+
+static inline void tcp_snd_cwnd_set(struct tcp_sock *tp, u32 val)
+{
+	WARN_ON_ONCE((int)val <= 0);
+	tp->snd_cwnd = val;
+}
+
 static inline bool tcp_in_slow_start(const struct tcp_sock *tp)
 {
-	return tp->snd_cwnd < tp->snd_ssthresh;
+	return tcp_snd_cwnd(tp) < tp->snd_ssthresh;
 }
 
 static inline bool tcp_in_initial_slowstart(const struct tcp_sock *tp)
@@ -1230,8 +1245,8 @@
 		return tp->snd_ssthresh;
 	else
 		return max(tp->snd_ssthresh,
-			   ((tp->snd_cwnd >> 1) +
-			    (tp->snd_cwnd >> 2)));
+			   ((tcp_snd_cwnd(tp) >> 1) +
+			    (tcp_snd_cwnd(tp) >> 2)));
 }
 
 /* Use define here intentionally to get WARN_ON location shown at the caller */
@@ -1271,11 +1286,14 @@
 {
 	const struct tcp_sock *tp = tcp_sk(sk);
 
+	if (tp->is_cwnd_limited)
+		return true;
+
 	/* If in slow start, ensure cwnd grows to twice what was ACKed. */
 	if (tcp_in_slow_start(tp))
-		return tp->snd_cwnd < 2 * tp->max_packets_out;
+		return tcp_snd_cwnd(tp) < 2 * tp->max_packets_out;
 
-	return tp->is_cwnd_limited;
+	return false;
 }
 
 /* BBR congestion control needs pacing.
@@ -1382,8 +1400,8 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	s32 delta;
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_slow_start_after_idle || tp->packets_out ||
-	    ca_ops->cong_control)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_slow_start_after_idle) ||
+	    tp->packets_out || ca_ops->cong_control)
 		return;
 	delta = tcp_jiffies32 - tp->lsndtime;
 	if (delta > inet_csk(sk)->icsk_rto)
@@ -1398,7 +1416,7 @@
 
 static inline int tcp_win_from_space(const struct sock *sk, int space)
 {
-	int tcp_adv_win_scale = sock_net(sk)->ipv4.sysctl_tcp_adv_win_scale;
+	int tcp_adv_win_scale = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_adv_win_scale);
 
 	return tcp_adv_win_scale <= 0 ?
 		(space>>(-tcp_adv_win_scale)) :
@@ -1460,22 +1478,38 @@
 static inline int keepalive_intvl_when(const struct tcp_sock *tp)
 {
 	struct net *net = sock_net((struct sock *)tp);
+	int val;
+
+	/* Paired with WRITE_ONCE() in tcp_sock_set_keepintvl()
+	 * and do_tcp_setsockopt().
+	 */
+	val = READ_ONCE(tp->keepalive_intvl);
 
-	return tp->keepalive_intvl ? : net->ipv4.sysctl_tcp_keepalive_intvl;
+	return val ? : READ_ONCE(net->ipv4.sysctl_tcp_keepalive_intvl);
 }
 
 static inline int keepalive_time_when(const struct tcp_sock *tp)
 {
 	struct net *net = sock_net((struct sock *)tp);
+	int val;
+
+	/* Paired with WRITE_ONCE() in tcp_sock_set_keepidle_locked() */
+	val = READ_ONCE(tp->keepalive_time);
 
-	return tp->keepalive_time ? : net->ipv4.sysctl_tcp_keepalive_time;
+	return val ? : READ_ONCE(net->ipv4.sysctl_tcp_keepalive_time);
 }
 
 static inline int keepalive_probes(const struct tcp_sock *tp)
 {
 	struct net *net = sock_net((struct sock *)tp);
+	int val;
 
-	return tp->keepalive_probes ? : net->ipv4.sysctl_tcp_keepalive_probes;
+	/* Paired with WRITE_ONCE() in tcp_sock_set_keepcnt()
+	 * and do_tcp_setsockopt().
+	 */
+	val = READ_ONCE(tp->keepalive_probes);
+
+	return val ? : READ_ONCE(net->ipv4.sysctl_tcp_keepalive_probes);
 }
 
 static inline u32 keepalive_time_elapsed(const struct tcp_sock *tp)
@@ -1488,7 +1522,8 @@
 
 static inline int tcp_fin_time(const struct sock *sk)
 {
-	int fin_timeout = tcp_sk(sk)->linger2 ? : sock_net(sk)->ipv4.sysctl_tcp_fin_timeout;
+	int fin_timeout = tcp_sk(sk)->linger2 ? :
+		READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fin_timeout);
 	const int rto = inet_csk(sk)->icsk_rto;
 
 	if (fin_timeout < (rto << 2) - (rto >> 1))
@@ -1982,7 +2017,11 @@
 static inline u32 tcp_notsent_lowat(const struct tcp_sock *tp)
 {
 	struct net *net = sock_net((struct sock *)tp);
-	return tp->notsent_lowat ?: net->ipv4.sysctl_tcp_notsent_lowat;
+	u32 val;
+
+	val = READ_ONCE(tp->notsent_lowat);
+
+	return val ?: READ_ONCE(net->ipv4.sysctl_tcp_notsent_lowat);
 }
 
 bool tcp_stream_memory_free(const struct sock *sk, int wake);
@@ -2084,9 +2123,26 @@
 {
 	const struct sk_buff *skb = tcp_rtx_queue_head(sk);
 	u32 rto = inet_csk(sk)->icsk_rto;
-	u64 rto_time_stamp_us = tcp_skb_timestamp_us(skb) + jiffies_to_usecs(rto);
 
-	return rto_time_stamp_us - tcp_sk(sk)->tcp_mstamp;
+	if (likely(skb)) {
+		u64 rto_time_stamp_us = tcp_skb_timestamp_us(skb) + jiffies_to_usecs(rto);
+
+		return rto_time_stamp_us - tcp_sk(sk)->tcp_mstamp;
+	} else {
+		WARN_ONCE(1,
+			"rtx queue emtpy: "
+			"out:%u sacked:%u lost:%u retrans:%u "
+			"tlp_high_seq:%u sk_state:%u ca_state:%u "
+			"advmss:%u mss_cache:%u pmtu:%u\n",
+			tcp_sk(sk)->packets_out, tcp_sk(sk)->sacked_out,
+			tcp_sk(sk)->lost_out, tcp_sk(sk)->retrans_out,
+			tcp_sk(sk)->tlp_high_seq, sk->sk_state,
+			inet_csk(sk)->icsk_ca_state,
+			tcp_sk(sk)->advmss, tcp_sk(sk)->mss_cache,
+			inet_csk(sk)->icsk_pmtu_cookie);
+		return jiffies_to_usecs(rto);
+	}
+
 }
 
 /*
@@ -2195,7 +2251,7 @@
 	/* cleanup ulp */
 	void (*release)(struct sock *sk);
 	/* diagnostic */
-	int (*get_info)(const struct sock *sk, struct sk_buff *skb);
+	int (*get_info)(struct sock *sk, struct sk_buff *skb);
 	size_t (*get_info_size)(const struct sock *sk);
 	/* clone ulp */
 	void (*clone)(const struct request_sock *req, struct sock *newsk,
@@ -2226,8 +2282,8 @@
 void tcp_bpf_clone(const struct sock *sk, struct sock *newsk);
 #endif /* CONFIG_BPF_SYSCALL */
 
-int tcp_bpf_sendmsg_redir(struct sock *sk, struct sk_msg *msg, u32 bytes,
-			  int flags);
+int tcp_bpf_sendmsg_redir(struct sock *sk, bool ingress,
+			  struct sk_msg *msg, u32 bytes, int flags);
 #endif /* CONFIG_NET_SOCK_MSG */
 
 #if !defined(CONFIG_BPF_SYSCALL) || !defined(CONFIG_NET_SOCK_MSG)
@@ -2324,7 +2380,7 @@
 
 	if (timeout <= 0)
 		timeout = TCP_TIMEOUT_INIT;
-	return timeout;
+	return min_t(int, timeout, TCP_RTO_MAX);
 }
 
 static inline u32 tcp_rwnd_init_bpf(struct sock *sk)
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/tls.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/tls.h
@@ -116,11 +116,6 @@
 	u8 aead_req_ctx[];
 };
 
-struct tls_msg {
-	struct strp_msg rxm;
-	u8 control;
-};
-
 struct tx_work {
 	struct delayed_work work;
 	struct sock *sk;
@@ -133,9 +128,6 @@
 	struct tls_rec *open_rec;
 	struct list_head tx_list;
 	atomic_t encrypt_pending;
-	/* protect crypto_wait with encrypt_pending */
-	spinlock_t encrypt_compl_lock;
-	int async_notify;
 	u8 async_capable:1;
 
 #define BIT_TX_SCHEDULED	0
@@ -151,13 +143,11 @@
 	void (*saved_data_ready)(struct sock *sk);
 
 	struct sk_buff *recv_pkt;
-	u8 control;
+	u8 reader_present;
 	u8 async_capable:1;
-	u8 decrypted:1;
+	u8 reader_contended:1;
 	atomic_t decrypt_pending;
-	/* protect crypto_wait with decrypt_pending*/
-	spinlock_t decrypt_compl_lock;
-	bool async_notify;
+	struct wait_queue_head wq;
 };
 
 struct tls_record_info {
@@ -179,6 +169,8 @@
 
 	struct scatterlist sg_tx_data[MAX_SKB_FRAGS];
 	void (*sk_destruct)(struct sock *sk);
+	struct work_struct destruct_work;
+	struct tls_context *ctx;
 	u8 driver_state[] __aligned(8);
 	/* The TLS layer reserves room for driver specific state
 	 * Currently the belief is that there is not enough
@@ -408,7 +400,9 @@
 
 static inline struct tls_msg *tls_msg(struct sk_buff *skb)
 {
-	return (struct tls_msg *)strp_msg(skb);
+	struct sk_skb_cb *scb = (struct sk_skb_cb *)skb->cb;
+
+	return &scb->tls;
 }
 
 static inline bool tls_is_partially_sent_record(struct tls_context *ctx)
@@ -425,7 +419,7 @@
 {
 	struct tls_rec *rec;
 
-	rec = list_first_entry(&ctx->tx_list, struct tls_rec, list);
+	rec = list_first_entry_or_null(&ctx->tx_list, struct tls_rec, list);
 	if (!rec)
 		return false;
 
@@ -707,7 +701,7 @@
 			 struct tls_crypto_info *crypto_info);
 
 #ifdef CONFIG_TLS_DEVICE
-void tls_device_init(void);
+int tls_device_init(void);
 void tls_device_cleanup(void);
 void tls_device_sk_destruct(struct sock *sk);
 int tls_set_device_offload(struct sock *sk, struct tls_context *ctx);
@@ -727,7 +721,7 @@
 	return tls_get_ctx(sk)->rx_conf == TLS_HW;
 }
 #else
-static inline void tls_device_init(void) {}
+static inline int tls_device_init(void) { return 0; }
 static inline void tls_device_cleanup(void) {}
 
 static inline int
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/udp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/udp.h
@@ -173,7 +173,7 @@
 INDIRECT_CALLABLE_DECLARE(struct sk_buff *udp6_gro_receive(struct list_head *,
 							   struct sk_buff *));
 INDIRECT_CALLABLE_DECLARE(int udp6_gro_complete(struct sk_buff *, int));
-INDIRECT_CALLABLE_DECLARE(void udp_v6_early_demux(struct sk_buff *));
+void udp_v6_early_demux(struct sk_buff *skb);
 INDIRECT_CALLABLE_DECLARE(int udpv6_rcv(struct sk_buff *));
 
 struct sk_buff *udp_gro_receive(struct list_head *head, struct sk_buff *skb,
@@ -262,7 +262,7 @@
 				       int dif, int sdif)
 {
 #if IS_ENABLED(CONFIG_NET_L3_MASTER_DEV)
-	return inet_bound_dev_eq(!!net->ipv4.sysctl_udp_l3mdev_accept,
+	return inet_bound_dev_eq(!!READ_ONCE(net->ipv4.sysctl_udp_l3mdev_accept),
 				 bound_dev_if, dif, sdif);
 #else
 	return inet_bound_dev_eq(true, bound_dev_if, dif, sdif);
@@ -270,7 +270,7 @@
 }
 
 /* net/ipv4/udp.c */
-void udp_destruct_sock(struct sock *sk);
+void udp_destruct_common(struct sock *sk);
 void skb_consume_udp(struct sock *sk, struct sk_buff *skb, int len);
 int __udp_enqueue_schedule_skb(struct sock *sk, struct sk_buff *skb);
 void udp_skb_destructor(struct sock *sk, struct sk_buff *skb);
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/udp_tunnel.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/udp_tunnel.h
@@ -67,6 +67,9 @@
 typedef int (*udp_tunnel_encap_rcv_t)(struct sock *sk, struct sk_buff *skb);
 typedef int (*udp_tunnel_encap_err_lookup_t)(struct sock *sk,
 					     struct sk_buff *skb);
+typedef void (*udp_tunnel_encap_err_rcv_t)(struct sock *sk,
+					   struct sk_buff *skb,
+					   unsigned int udp_offset);
 typedef void (*udp_tunnel_encap_destroy_t)(struct sock *sk);
 typedef struct sk_buff *(*udp_tunnel_gro_receive_t)(struct sock *sk,
 						    struct list_head *head,
@@ -80,6 +83,7 @@
 	__u8  encap_type;
 	udp_tunnel_encap_rcv_t encap_rcv;
 	udp_tunnel_encap_err_lookup_t encap_err_lookup;
+	udp_tunnel_encap_err_rcv_t encap_err_rcv;
 	udp_tunnel_encap_destroy_t encap_destroy;
 	udp_tunnel_gro_receive_t gro_receive;
 	udp_tunnel_gro_complete_t gro_complete;
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/udplite.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/udplite.h
@@ -24,14 +24,6 @@
 	return copy_from_iter_full(to, len, &msg->msg_iter) ? 0 : -EFAULT;
 }
 
-/* Designate sk as UDP-Lite socket */
-static inline int udplite_sk_init(struct sock *sk)
-{
-	udp_init_sock(sk);
-	udp_sk(sk)->pcflag = UDPLITE_BIT;
-	return 0;
-}
-
 /*
  * 	Checksumming routines
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/vxlan.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/vxlan.h
@@ -246,6 +246,8 @@
 	struct net	  *net;		/* netns for packet i/o */
 	struct vxlan_rdst default_dst;	/* default destination */
 
+	struct ip_tunnel_fan fan;
+
 	struct timer_list age_timer;
 	spinlock_t	  hash_lock[FDB_HASH_SIZE];
 	unsigned int	  addrcnt;
@@ -327,10 +329,15 @@
 	return features;
 }
 
-/* IP header + UDP + VXLAN + Ethernet header */
-#define VXLAN_HEADROOM (20 + 8 + 8 + 14)
-/* IPv6 header + UDP + VXLAN + Ethernet header */
-#define VXLAN6_HEADROOM (40 + 8 + 8 + 14)
+static inline int vxlan_headroom(u32 flags)
+{
+	/* VXLAN:     IP4/6 header + UDP + VXLAN + Ethernet header */
+	/* VXLAN-GPE: IP4/6 header + UDP + VXLAN */
+	return (flags & VXLAN_F_IPV6 ? sizeof(struct ipv6hdr) :
+				       sizeof(struct iphdr)) +
+	       sizeof(struct udphdr) + sizeof(struct vxlanhdr) +
+	       (flags & VXLAN_F_GPE ? 0 : ETH_HLEN);
+}
 
 static inline struct vxlanhdr *vxlan_hdr(struct sk_buff *skb)
 {
@@ -492,12 +499,12 @@
 }
 
 static inline bool vxlan_fdb_nh_path_select(struct nexthop *nh,
-					    int hash,
+					    u32 hash,
 					    struct vxlan_rdst *rdst)
 {
 	struct fib_nh_common *nhc;
 
-	nhc = nexthop_path_fdb_result(nh, hash);
+	nhc = nexthop_path_fdb_result(nh, hash >> 1);
 	if (unlikely(!nhc))
 		return false;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/xdp.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/xdp.h
@@ -260,6 +260,9 @@
 int xdp_rxq_info_reg_mem_model(struct xdp_rxq_info *xdp_rxq,
 			       enum xdp_mem_type type, void *allocator);
 void xdp_rxq_info_unreg_mem_model(struct xdp_rxq_info *xdp_rxq);
+int xdp_reg_mem_model(struct xdp_mem_info *mem,
+		      enum xdp_mem_type type, void *allocator);
+void xdp_unreg_mem_model(struct xdp_mem_info *mem);
 
 /* Drivers not supporting XDP metadata can use this helper, which
  * rejects any room expansion for metadata as a result.
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/xdp_sock_drv.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/xdp_sock_drv.h
@@ -13,7 +13,7 @@
 
 void xsk_tx_completed(struct xsk_buff_pool *pool, u32 nb_entries);
 bool xsk_tx_peek_desc(struct xsk_buff_pool *pool, struct xdp_desc *desc);
-u32 xsk_tx_peek_release_desc_batch(struct xsk_buff_pool *pool, struct xdp_desc *desc, u32 max);
+u32 xsk_tx_peek_release_desc_batch(struct xsk_buff_pool *pool, u32 max);
 void xsk_tx_release(struct xsk_buff_pool *pool);
 struct xsk_buff_pool *xsk_get_pool_from_qid(struct net_device *dev,
 					    u16 queue_id);
@@ -129,8 +129,7 @@
 	return false;
 }
 
-static inline u32 xsk_tx_peek_release_desc_batch(struct xsk_buff_pool *pool, struct xdp_desc *desc,
-						 u32 max)
+static inline u32 xsk_tx_peek_release_desc_batch(struct xsk_buff_pool *pool, u32 max)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/xfrm.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/xfrm.h
@@ -126,12 +126,18 @@
 	struct xfrm_address_filter *filter;
 };
 
-struct xfrm_state_offload {
+enum {
+	XFRM_DEV_OFFLOAD_IN = 1,
+	XFRM_DEV_OFFLOAD_OUT,
+};
+
+struct xfrm_dev_offload {
 	struct net_device	*dev;
 	struct net_device	*real_dev;
 	unsigned long		offload_handle;
 	unsigned int		num_exthdrs;
 	u8			flags;
+	u8			dir : 2;
 };
 
 struct xfrm_mode {
@@ -200,6 +206,11 @@
 	struct xfrm_algo_aead	*aead;
 	const char		*geniv;
 
+	/* mapping change rate limiting */
+	__be16 new_mapping_sport;
+	u32 new_mapping;	/* seconds */
+	u32 mapping_maxage;	/* seconds for input SA */
+
 	/* Data for encapsulator */
 	struct xfrm_encap_tmpl	*encap;
 	struct sock __rcu	*encap_sk;
@@ -241,7 +252,7 @@
 	struct xfrm_lifetime_cur curlft;
 	struct hrtimer		mtimer;
 
-	struct xfrm_state_offload xso;
+	struct xfrm_dev_offload xso;
 
 	/* used to fix curlft->add_time when changing date */
 	long		saved_tmo;
@@ -310,20 +321,25 @@
 void xfrm_if_register_cb(const struct xfrm_if_cb *ifcb);
 void xfrm_if_unregister_cb(void);
 
+struct xfrm_dst_lookup_params {
+	struct net *net;
+	int tos;
+	int oif;
+	xfrm_address_t *saddr;
+	xfrm_address_t *daddr;
+	u32 mark;
+	__u8 ipproto;
+	union flowi_uli uli;
+};
+
 struct net_device;
 struct xfrm_type;
 struct xfrm_dst;
 struct xfrm_policy_afinfo {
 	struct dst_ops		*dst_ops;
-	struct dst_entry	*(*dst_lookup)(struct net *net,
-					       int tos, int oif,
-					       const xfrm_address_t *saddr,
-					       const xfrm_address_t *daddr,
-					       u32 mark);
-	int			(*get_saddr)(struct net *net, int oif,
-					     xfrm_address_t *saddr,
-					     xfrm_address_t *daddr,
-					     u32 mark);
+	struct dst_entry	*(*dst_lookup)(const struct xfrm_dst_lookup_params *params);
+	int			(*get_saddr)(xfrm_address_t *saddr,
+					     const struct xfrm_dst_lookup_params *params);
 	int			(*fill_dst)(struct xfrm_dst *xdst,
 					    struct net_device *dev,
 					    const struct flowi *fl);
@@ -666,11 +682,13 @@
 
 	if (audit_enabled == AUDIT_OFF)
 		return NULL;
+	audit_stamp_context(audit_context());
 	audit_buf = audit_log_start(audit_context(), GFP_ATOMIC,
 				    AUDIT_MAC_IPSEC_EVENT);
 	if (audit_buf == NULL)
 		return NULL;
 	audit_log_format(audit_buf, "op=%s", op);
+	audit_log_lsm(NULL, false);
 	return audit_buf;
 }
 
@@ -684,7 +702,7 @@
 		AUDIT_SID_UNSET;
 
 	audit_log_format(audit_buf, " auid=%u ses=%u", auid, ses);
-	audit_log_task_context(audit_buf);
+	audit_log_task_context(audit_buf, NULL);
 }
 
 void xfrm_audit_policy_add(struct xfrm_policy *xp, int result, bool task_valid);
@@ -1014,6 +1032,9 @@
 #define CRYPTO_INVALID_PACKET_SYNTAX		64
 #define CRYPTO_INVALID_PROTOCOL			128
 
+	/* Used to keep whole l2 header for transport mode GRO */
+	__u32			orig_mac_len;
+
 	__u8			proto;
 	__u8			inner_ipproto;
 };
@@ -1021,6 +1042,7 @@
 struct sec_path {
 	int			len;
 	int			olen;
+	int			verified_cnt;
 
 	struct xfrm_state	*xvec[XFRM_MAX_DEPTH];
 	struct xfrm_offload	ovec[XFRM_MAX_OFFLOAD_DEPTH];
@@ -1075,24 +1097,29 @@
 }
 
 #ifdef CONFIG_XFRM
-static inline bool
-xfrm_default_allow(struct net *net, int dir)
+int __xfrm_policy_check(struct sock *, int dir, struct sk_buff *skb,
+			unsigned short family);
+
+static inline bool __xfrm_check_nopolicy(struct net *net, struct sk_buff *skb,
+					 int dir)
 {
-	u8 def = net->xfrm.policy_default;
+	if (!net->xfrm.policy_count[dir] && !secpath_exists(skb))
+		return net->xfrm.policy_default[dir] == XFRM_USERPOLICY_ACCEPT;
 
-	switch (dir) {
-	case XFRM_POLICY_IN:
-		return def & XFRM_POL_DEFAULT_IN ? false : true;
-	case XFRM_POLICY_OUT:
-		return def & XFRM_POL_DEFAULT_OUT ? false : true;
-	case XFRM_POLICY_FWD:
-		return def & XFRM_POL_DEFAULT_FWD ? false : true;
-	}
 	return false;
 }
 
-int __xfrm_policy_check(struct sock *, int dir, struct sk_buff *skb,
-			unsigned short family);
+static inline bool __xfrm_check_dev_nopolicy(struct sk_buff *skb,
+					     int dir, unsigned short family)
+{
+	if (dir != XFRM_POLICY_OUT && family == AF_INET) {
+		/* same dst may be used for traffic originating from
+		 * devices with different policy settings.
+		 */
+		return IPCB(skb)->flags & IPSKB_NOPOLICY;
+	}
+	return skb_dst(skb) && (skb_dst(skb)->flags & DST_NOPOLICY);
+}
 
 static inline int __xfrm_policy_check2(struct sock *sk, int dir,
 				       struct sk_buff *skb,
@@ -1104,13 +1131,9 @@
 	if (sk && sk->sk_policy[XFRM_POLICY_IN])
 		return __xfrm_policy_check(sk, ndir, skb, family);
 
-	if (xfrm_default_allow(net, dir))
-		return (!net->xfrm.policy_count[dir] && !secpath_exists(skb)) ||
-		       (skb_dst(skb) && (skb_dst(skb)->flags & DST_NOPOLICY)) ||
-		       __xfrm_policy_check(sk, ndir, skb, family);
-	else
-		return (skb_dst(skb) && (skb_dst(skb)->flags & DST_NOPOLICY)) ||
-		       __xfrm_policy_check(sk, ndir, skb, family);
+	return __xfrm_check_nopolicy(net, skb, dir) ||
+	       __xfrm_check_dev_nopolicy(skb, dir, family) ||
+	       __xfrm_policy_check(sk, ndir, skb, family);
 }
 
 static inline int xfrm_policy_check(struct sock *sk, int dir, struct sk_buff *skb, unsigned short family)
@@ -1162,13 +1185,12 @@
 {
 	struct net *net = dev_net(skb->dev);
 
-	if (xfrm_default_allow(net, XFRM_POLICY_FWD))
-		return !net->xfrm.policy_count[XFRM_POLICY_OUT] ||
-			(skb_dst(skb)->flags & DST_NOXFRM) ||
-			__xfrm_route_forward(skb, family);
-	else
-		return (skb_dst(skb)->flags & DST_NOXFRM) ||
-			__xfrm_route_forward(skb, family);
+	if (!net->xfrm.policy_count[XFRM_POLICY_OUT] &&
+	    net->xfrm.policy_default[XFRM_POLICY_OUT] == XFRM_USERPOLICY_ACCEPT)
+		return true;
+
+	return (skb_dst(skb)->flags & DST_NOXFRM) ||
+	       __xfrm_route_forward(skb, family);
 }
 
 static inline int xfrm4_route_forward(struct sk_buff *skb)
@@ -1185,6 +1207,8 @@
 
 static inline int xfrm_sk_clone_policy(struct sock *sk, const struct sock *osk)
 {
+	if (!sk_fullsock(osk))
+		return 0;
 	sk->sk_policy[0] = NULL;
 	sk->sk_policy[1] = NULL;
 	if (unlikely(osk->sk_policy[0] || osk->sk_policy[1]))
@@ -1562,7 +1586,6 @@
 void xfrm_spd_getinfo(struct net *net, struct xfrmk_spdinfo *si);
 u32 xfrm_replay_seqhi(struct xfrm_state *x, __be32 net_seq);
 int xfrm_init_replay(struct xfrm_state *x);
-u32 __xfrm_state_mtu(struct xfrm_state *x, int mtu);
 u32 xfrm_state_mtu(struct xfrm_state *x, int mtu);
 int __xfrm_init_state(struct xfrm_state *x, bool init_replay, bool offload);
 int xfrm_init_state(struct xfrm_state *x);
@@ -1635,10 +1658,7 @@
 }
 #endif
 
-struct dst_entry *__xfrm_dst_lookup(struct net *net, int tos, int oif,
-				    const xfrm_address_t *saddr,
-				    const xfrm_address_t *daddr,
-				    int family, u32 mark);
+struct dst_entry *__xfrm_dst_lookup(int family, const struct xfrm_dst_lookup_params *params);
 
 struct xfrm_policy *xfrm_policy_alloc(struct net *net, gfp_t gfp);
 
@@ -1675,14 +1695,15 @@
 	       const struct xfrm_migrate *m, int num_bundles,
 	       const struct xfrm_kmaddress *k,
 	       const struct xfrm_encap_tmpl *encap);
-struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net);
+struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net,
+						u32 if_id);
 struct xfrm_state *xfrm_state_migrate(struct xfrm_state *x,
 				      struct xfrm_migrate *m,
 				      struct xfrm_encap_tmpl *encap);
 int xfrm_migrate(const struct xfrm_selector *sel, u8 dir, u8 type,
 		 struct xfrm_migrate *m, int num_bundles,
 		 struct xfrm_kmaddress *k, struct net *net,
-		 struct xfrm_encap_tmpl *encap);
+		 struct xfrm_encap_tmpl *encap, u32 if_id);
 #endif
 
 int km_new_mapping(struct xfrm_state *x, xfrm_address_t *ipaddr, __be16 sport);
@@ -1872,7 +1893,7 @@
 
 static inline void xfrm_dev_state_advance_esn(struct xfrm_state *x)
 {
-	struct xfrm_state_offload *xso = &x->xso;
+	struct xfrm_dev_offload *xso = &x->xso;
 
 	if (xso->dev && xso->dev->xfrmdev_ops->xdo_dev_state_advance_esn)
 		xso->dev->xfrmdev_ops->xdo_dev_state_advance_esn(x);
@@ -1898,7 +1919,7 @@
 
 static inline void xfrm_dev_state_delete(struct xfrm_state *x)
 {
-	struct xfrm_state_offload *xso = &x->xso;
+	struct xfrm_dev_offload *xso = &x->xso;
 
 	if (xso->dev)
 		xso->dev->xfrmdev_ops->xdo_dev_state_delete(x);
@@ -1906,7 +1927,7 @@
 
 static inline void xfrm_dev_state_free(struct xfrm_state *x)
 {
-	struct xfrm_state_offload *xso = &x->xso;
+	struct xfrm_dev_offload *xso = &x->xso;
 	struct net_device *dev = xso->dev;
 
 	if (dev && dev->xfrmdev_ops) {
--- linux-xilinx-zynqmp-5.15.0.orig/include/net/xsk_buff_pool.h
+++ linux-xilinx-zynqmp-5.15.0/include/net/xsk_buff_pool.h
@@ -60,6 +60,7 @@
 	 */
 	dma_addr_t *dma_pages;
 	struct xdp_buff_xsk *heads;
+	struct xdp_desc *tx_descs;
 	u64 chunk_mask;
 	u64 addrs_cnt;
 	u32 free_list_cnt;
@@ -86,8 +87,9 @@
 						struct xdp_umem *umem);
 int xp_assign_dev(struct xsk_buff_pool *pool, struct net_device *dev,
 		  u16 queue_id, u16 flags);
-int xp_assign_dev_shared(struct xsk_buff_pool *pool, struct xdp_umem *umem,
+int xp_assign_dev_shared(struct xsk_buff_pool *pool, struct xdp_sock *umem_xs,
 			 struct net_device *dev, u16 queue_id);
+int xp_alloc_tx_descs(struct xsk_buff_pool *pool, struct xdp_sock *xs);
 void xp_destroy(struct xsk_buff_pool *pool);
 void xp_release(struct xdp_buff_xsk *xskb);
 void xp_get_pool(struct xsk_buff_pool *pool);
@@ -150,13 +152,8 @@
 	if (likely(!cross_pg))
 		return false;
 
-	if (pool->dma_pages_cnt) {
-		return !(pool->dma_pages[addr >> PAGE_SHIFT] &
-			 XSK_NEXT_PG_CONTIG_MASK);
-	}
-
-	/* skb path */
-	return addr + len > pool->addrs_cnt;
+	return pool->dma_pages_cnt &&
+	       !(pool->dma_pages[addr >> PAGE_SHIFT] & XSK_NEXT_PG_CONTIG_MASK);
 }
 
 static inline u64 xp_aligned_extract_addr(struct xsk_buff_pool *pool, u64 addr)
--- linux-xilinx-zynqmp-5.15.0.orig/include/rdma/ib_addr.h
+++ linux-xilinx-zynqmp-5.15.0/include/rdma/ib_addr.h
@@ -194,29 +194,6 @@
 		return 0;
 }
 
-static inline int iboe_get_rate(struct net_device *dev)
-{
-	struct ethtool_link_ksettings cmd;
-	int err;
-
-	rtnl_lock();
-	err = __ethtool_get_link_ksettings(dev, &cmd);
-	rtnl_unlock();
-	if (err)
-		return IB_RATE_PORT_CURRENT;
-
-	if (cmd.base.speed >= 40000)
-		return IB_RATE_40_GBPS;
-	else if (cmd.base.speed >= 30000)
-		return IB_RATE_30_GBPS;
-	else if (cmd.base.speed >= 20000)
-		return IB_RATE_20_GBPS;
-	else if (cmd.base.speed >= 10000)
-		return IB_RATE_10_GBPS;
-	else
-		return IB_RATE_PORT_CURRENT;
-}
-
 static inline int rdma_link_local_addr(struct in6_addr *addr)
 {
 	if (addr->s6_addr32[0] == htonl(0xfe800000) &&
--- linux-xilinx-zynqmp-5.15.0.orig/include/rdma/ib_mad.h
+++ linux-xilinx-zynqmp-5.15.0/include/rdma/ib_mad.h
@@ -276,6 +276,7 @@
 	IB_PORT_SWITCH_PORT_STATE_TABLE_SUP	= 1 << 3,
 	IB_PORT_LINK_WIDTH_2X_SUP		= 1 << 4,
 	IB_PORT_LINK_SPEED_HDR_SUP		= 1 << 5,
+	IB_PORT_LINK_SPEED_NDR_SUP		= 1 << 10,
 };
 
 #define OPA_CLASS_PORT_INFO_PR_SUPPORT BIT(26)
--- linux-xilinx-zynqmp-5.15.0.orig/include/rdma/ib_umem.h
+++ linux-xilinx-zynqmp-5.15.0/include/rdma/ib_umem.h
@@ -25,6 +25,8 @@
 	u32 writable : 1;
 	u32 is_odp : 1;
 	u32 is_dmabuf : 1;
+	/* Placing at the end of the bitfield list is ABI preserving on LE */
+	u32 is_peer : 1;
 	struct work_struct	work;
 	struct sg_append_table sgt_append;
 };
@@ -45,6 +47,12 @@
 	return container_of(umem, struct ib_umem_dmabuf, umem);
 }
 
+typedef void (*umem_invalidate_func_t)(struct ib_umem *umem, void *priv);
+enum ib_peer_mem_flags {
+	IB_PEER_MEM_ALLOW = 1 << 0,
+	IB_PEER_MEM_INVAL_SUPP = 1 << 1,
+};
+
 /* Returns the offset of the umem start relative to the first page. */
 static inline int ib_umem_offset(struct ib_umem *umem)
 {
@@ -77,6 +85,13 @@
 {
 	__rdma_block_iter_start(biter, umem->sgt_append.sgt.sgl,
 				umem->sgt_append.sgt.nents, pgsz);
+	biter->__sg_advance = ib_umem_offset(umem) & ~(pgsz - 1);
+	biter->__sg_numblocks = ib_umem_num_dma_blocks(umem, pgsz);
+}
+
+static inline bool __rdma_umem_block_iter_next(struct ib_block_iter *biter)
+{
+	return __rdma_block_iter_next(biter) && biter->__sg_numblocks--;
 }
 
 /**
@@ -92,7 +107,7 @@
  */
 #define rdma_umem_for_each_dma_block(umem, biter, pgsz)                        \
 	for (__rdma_umem_block_iter_start(biter, umem, pgsz);                  \
-	     __rdma_block_iter_next(biter);)
+	     __rdma_umem_block_iter_next(biter);)
 
 #ifdef CONFIG_INFINIBAND_USER_MEM
 
@@ -142,6 +157,13 @@
 int ib_umem_dmabuf_map_pages(struct ib_umem_dmabuf *umem_dmabuf);
 void ib_umem_dmabuf_unmap_pages(struct ib_umem_dmabuf *umem_dmabuf);
 void ib_umem_dmabuf_release(struct ib_umem_dmabuf *umem_dmabuf);
+struct ib_umem *ib_umem_get_peer(struct ib_device *device, unsigned long addr,
+				 size_t size, int access,
+				 unsigned long peer_mem_flags);
+void ib_umem_activate_invalidation_notifier(struct ib_umem *umem,
+					   umem_invalidate_func_t func,
+					   void *cookie);
+void ib_umem_stop_invalidation_notifier(struct ib_umem *umem);
 
 #else /* CONFIG_INFINIBAND_USER_MEM */
 
@@ -185,6 +207,20 @@
 }
 static inline void ib_umem_dmabuf_unmap_pages(struct ib_umem_dmabuf *umem_dmabuf) { }
 static inline void ib_umem_dmabuf_release(struct ib_umem_dmabuf *umem_dmabuf) { }
+static inline struct ib_umem *ib_umem_get_peer(struct ib_device *device,
+					       unsigned long addr, size_t size,
+					       int access,
+					       unsigned long peer_mem_flags)
+{
+	return ERR_PTR(-EINVAL);
+}
+static inline void ib_umem_activate_invalidation_notifier(
+	struct ib_umem *umem, umem_invalidate_func_t func, void *cookie)
+{
+}
+static inline void ib_umem_stop_invalidation_notifier(struct ib_umem *umem)
+{
+}
 
 #endif /* CONFIG_INFINIBAND_USER_MEM */
 #endif /* IB_UMEM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/rdma/ib_verbs.h
+++ linux-xilinx-zynqmp-5.15.0/include/rdma/ib_verbs.h
@@ -2707,6 +2707,7 @@
 	 * It is a NULL terminated array.
 	 */
 	const struct attribute_group	*groups[4];
+	u8				hw_stats_attr_index;
 
 	u64			     uverbs_cmd_mask;
 
@@ -2817,6 +2818,7 @@
 	/* internal states */
 	struct scatterlist *__sg;	/* sg holding the current aligned block */
 	dma_addr_t __dma_addr;		/* unaligned DMA address of this block */
+	size_t __sg_numblocks;		/* ib_umem_num_dma_blocks() */
 	unsigned int __sg_nents;	/* number of SG entries */
 	unsigned int __sg_advance;	/* number of bytes to advance in sg in next step */
 	unsigned int __pg_bit;		/* alignment of current block */
@@ -4097,8 +4099,13 @@
 					   enum dma_data_direction direction,
 					   unsigned long dma_attrs)
 {
+	int nents;
+
 	if (ib_uses_virt_dma(dev)) {
-		ib_dma_virt_map_sg(dev, sgt->sgl, sgt->orig_nents);
+		nents = ib_dma_virt_map_sg(dev, sgt->sgl, sgt->orig_nents);
+		if (!nents)
+			return -EIO;
+		sgt->nents = nents;
 		return 0;
 	}
 	return dma_map_sgtable(dev->dma_device, sgt, direction, dma_attrs);
--- linux-xilinx-zynqmp-5.15.0.orig/include/rdma/peer_mem.h
+++ linux-xilinx-zynqmp-5.15.0/include/rdma/peer_mem.h
@@ -0,0 +1,175 @@
+/* SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB */
+/*
+ * Copyright (c) 2014-2020,  Mellanox Technologies. All rights reserved.
+ */
+#ifndef RDMA_PEER_MEM_H
+#define RDMA_PEER_MEM_H
+
+#include <linux/scatterlist.h>
+
+#define IB_PEER_MEMORY_NAME_MAX 64
+#define IB_PEER_MEMORY_VER_MAX 16
+
+/*
+ * Prior versions used a void * for core_context, at some point this was
+ * switched to use u64. Be careful if compiling this as 32 bit. To help the
+ * value of core_context is limited to u32 so it should work OK despite the
+ * type change.
+ */
+#define PEER_MEM_U64_CORE_CONTEXT
+
+struct device;
+
+/**
+ *  struct peer_memory_client - registration information for user virtual
+ *                              memory handlers
+ *
+ * The peer_memory_client scheme allows a driver to register with the ib_umem
+ * system that it has the ability to understand user virtual address ranges
+ * that are not compatible with get_user_pages(). For instance VMAs created
+ * with io_remap_pfn_range(), or other driver special VMA.
+ *
+ * For ranges the interface understands it can provide a DMA mapped sg_table
+ * for use by the ib_umem, allowing user virtual ranges that cannot be
+ * supported by get_user_pages() to be used as umems.
+ */
+struct peer_memory_client {
+	char name[IB_PEER_MEMORY_NAME_MAX];
+	char version[IB_PEER_MEMORY_VER_MAX];
+
+	/**
+	 * acquire - Begin working with a user space virtual address range
+	 *
+	 * @addr - Virtual address to be checked whether belongs to peer.
+	 * @size - Length of the virtual memory area starting at addr.
+	 * @peer_mem_private_data - Obsolete, always NULL
+	 * @peer_mem_name - Obsolete, always NULL
+	 * @client_context - Returns an opaque value for this acquire use in
+	 *                   other APIs
+	 *
+	 * Returns 1 if the peer_memory_client supports the entire virtual
+	 * address range, 0 or -ERRNO otherwise.  If 1 is returned then
+	 * release() will be called to release the acquire().
+	 */
+	int (*acquire)(unsigned long addr, size_t size,
+		       void *peer_mem_private_data, char *peer_mem_name,
+		       void **client_context);
+	/**
+	 * get_pages - Fill in the first part of a sg_table for a virtual
+	 *             address range
+	 *
+	 * @addr - Virtual address to be checked whether belongs to peer.
+	 * @size - Length of the virtual memory area starting at addr.
+	 * @write - Always 1
+	 * @force - 1 if write is required
+	 * @sg_head - Obsolete, always NULL
+	 * @client_context - Value returned by acquire()
+	 * @core_context - Value to be passed to invalidate_peer_memory for
+	 *                 this get
+	 *
+	 * addr/size are passed as the raw virtual address range requested by
+	 * the user, it is not aligned to any page size. get_pages() is always
+	 * followed by dma_map().
+	 *
+	 * Upon return the caller can call the invalidate_callback().
+	 *
+	 * Returns 0 on success, -ERRNO on failure. After success put_pages()
+	 * will be called to return the pages.
+	 */
+	int (*get_pages)(unsigned long addr, size_t size, int write, int force,
+			 struct sg_table *sg_head, void *client_context,
+			 u64 core_context);
+	/**
+	 * dma_map - Create a DMA mapped sg_table
+	 *
+	 * @sg_head - The sg_table to allocate
+	 * @client_context - Value returned by acquire()
+	 * @dma_device - The device that will be doing DMA from these addresses
+	 * @dmasync - Obsolete, always 0
+	 * @nmap - Returns the number of dma mapped entries in the sg_head
+	 *
+	 * Must be called after get_pages(). This must fill in the sg_head with
+	 * DMA mapped SGLs for dma_device. Each SGL start and end must meet a
+	 * minimum alignment of at least PAGE_SIZE, though individual sgls can
+	 * be multiples of PAGE_SIZE, in any mixture. Since the user virtual
+	 * address/size are not page aligned, the implementation must increase
+	 * it to the logical alignment when building the SGLs.
+	 *
+	 * Returns 0 on success, -ERRNO on failure. After success dma_unmap()
+	 * will be called to unmap the pages. On failure sg_head must be left
+	 * untouched or point to a valid sg_table.
+	 */
+	int (*dma_map)(struct sg_table *sg_head, void *client_context,
+		       struct device *dma_device, int dmasync, int *nmap);
+	/**
+	 * dma_unmap - Unmap a DMA mapped sg_table
+	 *
+	 * @sg_head - The sg_table to unmap
+	 * @client_context - Value returned by acquire()
+	 * @dma_device - The device that will be doing DMA from these addresses
+	 *
+	 * sg_head will not be touched after this function returns.
+	 *
+	 * Must return 0.
+	 */
+	int (*dma_unmap)(struct sg_table *sg_head, void *client_context,
+			 struct device *dma_device);
+	/**
+	 * put_pages - Unpin a SGL
+	 *
+	 * @sg_head - The sg_table to unpin
+	 * @client_context - Value returned by acquire()
+	 *
+	 * sg_head must be freed on return.
+	 */
+	void (*put_pages)(struct sg_table *sg_head, void *client_context);
+	/* Client should always return PAGE_SIZE */
+	unsigned long (*get_page_size)(void *client_context);
+	/**
+	 * release - Undo acquire
+	 *
+	 * @client_context - Value returned by acquire()
+	 *
+	 * If acquire() returns 1 then release() must be called. All
+	 * get_pages() and dma_map()'s must be undone before calling this
+	 * function.
+	 */
+	void (*release)(void *client_context);
+};
+
+enum {
+	PEER_MEM_INVALIDATE_UNMAPS = 1 << 0,
+};
+
+struct peer_memory_client_ex {
+	struct peer_memory_client client;
+	size_t ex_size;
+	u32 flags;
+};
+
+/*
+ * If invalidate_callback() is non-NULL then the client will only support
+ * umems which can be invalidated. The caller may call the
+ * invalidate_callback() after acquire() on return the range will no longer
+ * have DMA active, and release() will have been called.
+ *
+ * Note: The implementation locking must ensure that get_pages(), and
+ * dma_map() do not have locking dependencies with invalidate_callback(). The
+ * ib_core will wait until any concurrent get_pages() or dma_map() completes
+ * before returning.
+ *
+ * Similarly, this can call dma_unmap(), put_pages() and release() from within
+ * the callback, or will wait for another thread doing those operations to
+ * complete.
+ *
+ * For these reasons the user of invalidate_callback() must be careful with
+ * locking.
+ */
+typedef int (*invalidate_peer_memory)(void *reg_handle, u64 core_context);
+
+void *
+ib_register_peer_memory_client(const struct peer_memory_client *peer_client,
+			       invalidate_peer_memory *invalidate_callback);
+void ib_unregister_peer_memory_client(void *reg_handle);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/rdma/rdma_netlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/rdma/rdma_netlink.h
@@ -30,7 +30,7 @@
  * constant as well and the compiler checks they are the same.
  */
 #define MODULE_ALIAS_RDMA_NETLINK(_index, _val)                                \
-	static inline void __chk_##_index(void)                                \
+	static inline void __maybe_unused __chk_##_index(void)                 \
 	{                                                                      \
 		BUILD_BUG_ON(_index != _val);                                  \
 	}                                                                      \
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/libfcoe.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/libfcoe.h
@@ -249,7 +249,8 @@
 			 struct fc_frame *);
 
 /* libfcoe funcs */
-u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
+u64 fcoe_wwn_from_mac(unsigned char mac[ETH_ALEN], unsigned int scheme,
+		      unsigned int port);
 int fcoe_libfc_config(struct fc_lport *, struct fcoe_ctlr *,
 		      const struct libfc_function_template *, int init_fcp);
 u32 fcoe_fc_crc(struct fc_frame *fp);
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/libiscsi.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/libiscsi.h
@@ -52,8 +52,10 @@
 
 #define ISID_SIZE			6
 
-/* Connection suspend "bit" */
-#define ISCSI_SUSPEND_BIT		1
+/* Connection flags */
+#define ISCSI_CONN_FLAG_SUSPEND_TX	0
+#define ISCSI_CONN_FLAG_SUSPEND_RX	1
+#define ISCSI_CONN_FLAG_BOUND		2
 
 #define ISCSI_ITT_MASK			0x1fff
 #define ISCSI_TOTAL_CMDS_MAX		4096
@@ -199,8 +201,9 @@
 	struct list_head	cmdqueue;	/* data-path cmd queue */
 	struct list_head	requeue;	/* tasks needing another run */
 	struct work_struct	xmitwork;	/* per-conn. xmit workqueue */
-	unsigned long		suspend_tx;	/* suspend Tx */
-	unsigned long		suspend_rx;	/* suspend Rx */
+	/* recv */
+	struct work_struct	recvwork;
+	unsigned long		flags;		/* ISCSI_CONN_FLAGs */
 
 	/* negotiated params */
 	unsigned		max_recv_dlength; /* initiator_max_recv_dsl*/
@@ -399,7 +402,7 @@
 extern struct Scsi_Host *iscsi_host_alloc(struct scsi_host_template *sht,
 					  int dd_data_size,
 					  bool xmit_can_sleep);
-extern void iscsi_host_remove(struct Scsi_Host *shost);
+extern void iscsi_host_remove(struct Scsi_Host *shost, bool is_shutdown);
 extern void iscsi_host_free(struct Scsi_Host *shost);
 extern int iscsi_target_alloc(struct scsi_target *starget);
 extern int iscsi_host_get_max_scsi_cmds(struct Scsi_Host *shost,
@@ -411,6 +414,8 @@
 extern struct iscsi_cls_session *
 iscsi_session_setup(struct iscsi_transport *, struct Scsi_Host *shost,
 		    uint16_t, int, int, uint32_t, unsigned int);
+void iscsi_session_remove(struct iscsi_cls_session *cls_session);
+void iscsi_session_free(struct iscsi_cls_session *cls_session);
 extern void iscsi_session_teardown(struct iscsi_cls_session *);
 extern void iscsi_session_recovery_timedout(struct iscsi_cls_session *);
 extern int iscsi_set_param(struct iscsi_cls_conn *cls_conn,
@@ -440,8 +445,10 @@
 extern int iscsi_conn_get_addr_param(struct sockaddr_storage *addr,
 				     enum iscsi_param param, char *buf);
 extern void iscsi_suspend_tx(struct iscsi_conn *conn);
+extern void iscsi_suspend_rx(struct iscsi_conn *conn);
 extern void iscsi_suspend_queue(struct iscsi_conn *conn);
-extern void iscsi_conn_queue_work(struct iscsi_conn *conn);
+extern void iscsi_conn_queue_xmit(struct iscsi_conn *conn);
+extern void iscsi_conn_queue_recv(struct iscsi_conn *conn);
 
 #define iscsi_conn_printk(prefix, _c, fmt, a...) \
 	iscsi_cls_conn_printk(prefix, ((struct iscsi_conn *)_c)->cls_conn, \
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/scsi_cmnd.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/scsi_cmnd.h
@@ -65,10 +65,16 @@
 #define SCMD_STATE_COMPLETE	0
 #define SCMD_STATE_INFLIGHT	1
 
+enum scsi_cmnd_submitter {
+	SUBMITTED_BY_BLOCK_LAYER = 0,
+	SUBMITTED_BY_SCSI_ERROR_HANDLER = 1,
+	SUBMITTED_BY_SCSI_RESET_IOCTL = 2,
+} __packed;
+
 struct scsi_cmnd {
 	struct scsi_request req;
 	struct scsi_device *device;
-	struct list_head eh_entry; /* entry for the host eh_cmd_q */
+	struct list_head eh_entry; /* entry for the host eh_abort_list/eh_cmd_q */
 	struct delayed_work abort_work;
 
 	struct rcu_head rcu;
@@ -90,6 +96,7 @@
 	unsigned char prot_op;
 	unsigned char prot_type;
 	unsigned char prot_flags;
+	enum scsi_cmnd_submitter submitter;
 
 	unsigned short cmd_len;
 	enum dma_data_direction sc_data_direction;
@@ -165,6 +172,8 @@
 	return *(struct scsi_driver **)rq->rq_disk->private_data;
 }
 
+void scsi_done(struct scsi_cmnd *cmd);
+
 extern void scsi_finish_command(struct scsi_cmnd *cmd);
 
 extern void *scsi_kmap_atomic_sg(struct scatterlist *sg, int sg_count,
@@ -211,7 +220,7 @@
 	for_each_sg(scsi_sglist(cmd), sg, nseg, __i)
 
 static inline int scsi_sg_copy_from_buffer(struct scsi_cmnd *cmd,
-					   void *buf, int buflen)
+					   const void *buf, int buflen)
 {
 	return sg_copy_from_buffer(scsi_sglist(cmd), scsi_sg_count(cmd),
 				   buf, buflen);
@@ -238,7 +247,7 @@
 
 static inline unsigned int scsi_logical_block_count(struct scsi_cmnd *scmd)
 {
-	unsigned int shift = ilog2(scmd->device->sector_size) - SECTOR_SHIFT;
+	unsigned int shift = ilog2(scmd->device->sector_size);
 
 	return blk_rq_bytes(scsi_cmd_to_rq(scmd)) >> shift;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/scsi_device.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/scsi_device.h
@@ -206,6 +206,7 @@
 	unsigned rpm_autosuspend:1;	/* Enable runtime autosuspend at device
 					 * creation time */
 	unsigned ignore_media_change:1; /* Ignore MEDIA CHANGE on resume */
+	unsigned silence_suspend:1;	/* Do not print runtime PM related messages */
 
 	bool offline_already;		/* Device offline message logged */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/scsi_host.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/scsi_host.h
@@ -556,6 +556,7 @@
 
 	struct mutex		scan_mutex;/* serialize scanning activity */
 
+	struct list_head	eh_abort_list;
 	struct list_head	eh_cmd_q;
 	struct task_struct    * ehandler;  /* Error recovery thread. */
 	struct completion     * eh_action; /* Wait for specific actions on the
@@ -564,6 +565,8 @@
 	struct scsi_host_template *hostt;
 	struct scsi_transport_template *transportt;
 
+	struct kref		tagset_refcnt;
+	struct completion	tagset_freed;
 	/* Area to keep a shared tag map */
 	struct blk_mq_tag_set	tag_set;
 
@@ -761,7 +764,7 @@
 extern struct Scsi_Host *scsi_host_get(struct Scsi_Host *);
 extern int scsi_host_busy(struct Scsi_Host *shost);
 extern void scsi_host_put(struct Scsi_Host *t);
-extern struct Scsi_Host *scsi_host_lookup(unsigned short);
+extern struct Scsi_Host *scsi_host_lookup(unsigned int hostnum);
 extern const char *scsi_host_state_name(enum scsi_host_state);
 extern void scsi_host_complete_all_commands(struct Scsi_Host *shost,
 					    enum scsi_host_status status);
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/scsi_transport_iscsi.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/scsi_transport_iscsi.h
@@ -211,6 +211,8 @@
 	struct mutex ep_mutex;
 	struct iscsi_endpoint *ep;
 
+	/* Used when accessing flags and queueing work. */
+	spinlock_t lock;
 	unsigned long flags;
 	struct work_struct cleanup_work;
 
@@ -234,6 +236,14 @@
 	ISCSI_SESSION_FREE,
 };
 
+enum {
+	ISCSI_SESSION_TARGET_UNBOUND,
+	ISCSI_SESSION_TARGET_ALLOCATED,
+	ISCSI_SESSION_TARGET_SCANNED,
+	ISCSI_SESSION_TARGET_UNBINDING,
+	ISCSI_SESSION_TARGET_MAX,
+};
+
 #define ISCSI_MAX_TARGET -1
 
 struct iscsi_cls_session {
@@ -260,6 +270,7 @@
 	 */
 	pid_t creator;
 	int state;
+	int target_state;			/* session target bind state */
 	int sid;				/* session id */
 	void *dd_data;				/* LLD private data */
 	struct device dev;	/* sysfs transport/container device */
@@ -294,7 +305,7 @@
 struct iscsi_endpoint {
 	void *dd_data;			/* LLD private data */
 	struct device dev;
-	uint64_t id;
+	int id;
 	struct iscsi_cls_conn *conn;
 };
 
@@ -439,6 +450,7 @@
 						struct iscsi_transport *t,
 						int dd_size,
 						unsigned int target_id);
+extern void iscsi_force_destroy_session(struct iscsi_cls_session *session);
 extern void iscsi_remove_session(struct iscsi_cls_session *session);
 extern void iscsi_free_session(struct iscsi_cls_session *session);
 extern struct iscsi_cls_conn *iscsi_create_conn(struct iscsi_cls_session *sess,
--- linux-xilinx-zynqmp-5.15.0.orig/include/scsi/scsi_transport_sas.h
+++ linux-xilinx-zynqmp-5.15.0/include/scsi/scsi_transport_sas.h
@@ -199,6 +199,8 @@
 void sas_disable_tlr(struct scsi_device *);
 void sas_enable_tlr(struct scsi_device *);
 
+bool sas_ata_ncq_prio_supported(struct scsi_device *sdev);
+
 extern struct sas_rphy *sas_end_device_alloc(struct sas_port *);
 extern struct sas_rphy *sas_expander_alloc(struct sas_port *, enum sas_device_type);
 void sas_rphy_free(struct sas_rphy *);
--- linux-xilinx-zynqmp-5.15.0.orig/include/soc/at91/sama7-ddr.h
+++ linux-xilinx-zynqmp-5.15.0/include/soc/at91/sama7-ddr.h
@@ -11,8 +11,6 @@
 #ifndef __SAMA7_DDR_H__
 #define __SAMA7_DDR_H__
 
-#ifdef CONFIG_SOC_SAMA7
-
 /* DDR3PHY */
 #define DDR3PHY_PIR				(0x04)		/* DDR3PHY PHY Initialization Register	*/
 #define	DDR3PHY_PIR_DLLBYP		(1 << 17)	/* DLL Bypass */
@@ -28,7 +26,10 @@
 #define	DDR3PHY_PGSR				(0x0C)		/* DDR3PHY PHY General Status Register */
 #define		DDR3PHY_PGSR_IDONE		(1 << 0)	/* Initialization Done */
 
-#define DDR3PHY_ACIOCR				(0x24)		/*  DDR3PHY AC I/O Configuration Register */
+#define	DDR3PHY_ACDLLCR				(0x14)		/* DDR3PHY AC DLL Control Register */
+#define		DDR3PHY_ACDLLCR_DLLSRST		(1 << 30)	/* DLL Soft Reset */
+
+#define DDR3PHY_ACIOCR				(0x24)		/* DDR3PHY AC I/O Configuration Register */
 #define		DDR3PHY_ACIOCR_CSPDD_CS0	(1 << 18)	/* CS#[0] Power Down Driver */
 #define		DDR3PHY_ACIOCR_CKPDD_CK0	(1 << 8)	/* CK[0] Power Down Driver */
 #define		DDR3PHY_ACIORC_ACPDD		(1 << 3)	/* AC Power Down Driver */
@@ -40,6 +41,14 @@
 #define		DDR3PHY_DSGCR_ODTPDD_ODT0	(1 << 20)	/* ODT[0] Power Down Driver */
 
 #define DDR3PHY_ZQ0SR0				(0x188)		/* ZQ status register 0 */
+#define DDR3PHY_ZQ0SR0_PDO_OFF			(0)		/* Pull-down output impedance select offset */
+#define DDR3PHY_ZQ0SR0_PUO_OFF			(5)		/* Pull-up output impedance select offset */
+#define DDR3PHY_ZQ0SR0_PDODT_OFF		(10)		/* Pull-down on-die termination impedance select offset */
+#define DDR3PHY_ZQ0SRO_PUODT_OFF		(15)		/* Pull-up on-die termination impedance select offset */
+
+#define	DDR3PHY_DX0DLLCR			(0x1CC)		/* DDR3PHY DATX8 DLL Control Register */
+#define	DDR3PHY_DX1DLLCR			(0x20C)		/* DDR3PHY DATX8 DLL Control Register */
+#define		DDR3PHY_DXDLLCR_DLLDIS		(1 << 31)	/* DLL Disable */
 
 /* UDDRC */
 #define UDDRC_STAT				(0x04)		/* UDDRC Operating Mode Status Register */
@@ -75,6 +84,4 @@
 #define UDDRC_PCTRL_3				(0x6A0)		/* UDDRC Port 3 Control Register */
 #define UDDRC_PCTRL_4				(0x750)		/* UDDRC Port 4 Control Register */
 
-#endif /* CONFIG_SOC_SAMA7 */
-
 #endif /* __SAMA7_DDR_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/soc/fsl/qman.h
+++ linux-xilinx-zynqmp-5.15.0/include/soc/fsl/qman.h
@@ -1172,6 +1172,15 @@
 void qman_delete_cgr_safe(struct qman_cgr *cgr);
 
 /**
+ * qman_update_cgr_safe - Modifies a congestion group object from any CPU
+ * @cgr: the 'cgr' object to modify
+ * @opts: state of the CGR settings
+ *
+ * This will select the proper CPU and modify the CGR settings.
+ */
+int qman_update_cgr_safe(struct qman_cgr *cgr, struct qm_mcc_initcgr *opts);
+
+/**
  * qman_query_cgr_congested - Queries CGR's congestion status
  * @cgr: the 'cgr' object to query
  * @result: returns 'cgr's congestion status, 1 (true) if congested
--- linux-xilinx-zynqmp-5.15.0.orig/include/soc/qcom/cmd-db.h
+++ linux-xilinx-zynqmp-5.15.0/include/soc/qcom/cmd-db.h
@@ -1,5 +1,8 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-/* Copyright (c) 2016-2018, The Linux Foundation. All rights reserved. */
+/*
+ * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
 
 #ifndef __QCOM_COMMAND_DB_H__
 #define __QCOM_COMMAND_DB_H__
@@ -21,6 +24,8 @@
 
 const void *cmd_db_read_aux_data(const char *resource_id, size_t *len);
 
+bool cmd_db_match_resource_addr(u32 addr1, u32 addr2);
+
 enum cmd_db_hw_type cmd_db_read_slave_id(const char *resource_id);
 
 int cmd_db_ready(void);
@@ -31,6 +36,9 @@
 static inline const void *cmd_db_read_aux_data(const char *resource_id, size_t *len)
 { return ERR_PTR(-ENODEV); }
 
+static inline bool cmd_db_match_resource_addr(u32 addr1, u32 addr2)
+{ return false; }
+
 static inline enum cmd_db_hw_type cmd_db_read_slave_id(const char *resource_id)
 { return -ENODEV; }
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/control.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/control.h
@@ -109,7 +109,7 @@
 	int preferred_subdevice[SND_CTL_SUBDEV_ITEMS];
 	wait_queue_head_t change_sleep;
 	spinlock_t read_lock;
-	struct fasync_struct *fasync;
+	struct snd_fasync *fasync;
 	int subscribed;			/* read interface is activated */
 	struct list_head events;	/* waiting events for read */
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/core.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/core.h
@@ -284,6 +284,7 @@
 void snd_card_disconnect_sync(struct snd_card *card);
 int snd_card_free(struct snd_card *card);
 int snd_card_free_when_closed(struct snd_card *card);
+int snd_card_free_on_error(struct device *dev, int ret);
 void snd_card_set_id(struct snd_card *card, const char *id);
 int snd_card_register(struct snd_card *card);
 int snd_card_info_init(void);
@@ -500,4 +501,12 @@
 }
 #endif
 
+/* async signal helpers */
+struct snd_fasync;
+
+int snd_fasync_helper(int fd, struct file *file, int on,
+		      struct snd_fasync **fasyncp);
+void snd_kill_fasync(struct snd_fasync *fasync, int signal, int poll);
+void snd_fasync_free(struct snd_fasync *fasync);
+
 #endif /* __SOUND_CORE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/cs35l41.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/cs35l41.h
@@ -0,0 +1,779 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * linux/sound/cs35l41.h -- Platform data for CS35L41
+ *
+ * Copyright (c) 2017-2021 Cirrus Logic Inc.
+ *
+ * Author: David Rhodes	<david.rhodes@cirrus.com>
+ */
+
+#ifndef __CS35L41_H
+#define __CS35L41_H
+
+#include <linux/regmap.h>
+
+#define CS35L41_FIRSTREG		0x00000000
+#define CS35L41_LASTREG			0x03804FE8
+#define CS35L41_DEVID			0x00000000
+#define CS35L41_REVID			0x00000004
+#define CS35L41_FABID			0x00000008
+#define CS35L41_RELID			0x0000000C
+#define CS35L41_OTPID			0x00000010
+#define CS35L41_SFT_RESET		0x00000020
+#define CS35L41_TEST_KEY_CTL		0x00000040
+#define CS35L41_USER_KEY_CTL		0x00000044
+#define CS35L41_OTP_MEM0		0x00000400
+#define CS35L41_OTP_MEM31		0x0000047C
+#define CS35L41_OTP_CTRL0		0x00000500
+#define CS35L41_OTP_CTRL1		0x00000504
+#define CS35L41_OTP_CTRL3		0x00000508
+#define CS35L41_OTP_CTRL4		0x0000050C
+#define CS35L41_OTP_CTRL5		0x00000510
+#define CS35L41_OTP_CTRL6		0x00000514
+#define CS35L41_OTP_CTRL7		0x00000518
+#define CS35L41_OTP_CTRL8		0x0000051C
+#define CS35L41_PWR_CTRL1		0x00002014
+#define CS35L41_PWR_CTRL2		0x00002018
+#define CS35L41_PWR_CTRL3		0x0000201C
+#define CS35L41_CTRL_OVRRIDE		0x00002020
+#define CS35L41_AMP_OUT_MUTE		0x00002024
+#define CS35L41_PROTECT_REL_ERR_IGN	0x00002034
+#define CS35L41_GPIO_PAD_CONTROL	0x0000242C
+#define CS35L41_JTAG_CONTROL		0x00002438
+#define CS35L41_PWRMGT_CTL		0x00002900
+#define CS35L41_WAKESRC_CTL		0x00002904
+#define CS35L41_PWRMGT_STS		0x00002908
+#define CS35L41_PLL_CLK_CTRL		0x00002C04
+#define CS35L41_DSP_CLK_CTRL		0x00002C08
+#define CS35L41_GLOBAL_CLK_CTRL		0x00002C0C
+#define CS35L41_DATA_FS_SEL		0x00002C10
+#define CS35L41_TST_FS_MON0		0x00002D10
+#define CS35L41_MDSYNC_EN		0x00003400
+#define CS35L41_MDSYNC_TX_ID		0x00003408
+#define CS35L41_MDSYNC_PWR_CTRL		0x0000340C
+#define CS35L41_MDSYNC_DATA_TX		0x00003410
+#define CS35L41_MDSYNC_TX_STATUS	0x00003414
+#define CS35L41_MDSYNC_DATA_RX		0x0000341C
+#define CS35L41_MDSYNC_RX_STATUS	0x00003420
+#define CS35L41_MDSYNC_ERR_STATUS	0x00003424
+#define CS35L41_MDSYNC_SYNC_PTE2	0x00003528
+#define CS35L41_MDSYNC_SYNC_PTE3	0x0000352C
+#define CS35L41_MDSYNC_SYNC_MSM_STATUS	0x0000353C
+#define CS35L41_BSTCVRT_VCTRL1		0x00003800
+#define CS35L41_BSTCVRT_VCTRL2		0x00003804
+#define CS35L41_BSTCVRT_PEAK_CUR	0x00003808
+#define CS35L41_BSTCVRT_SFT_RAMP	0x0000380C
+#define CS35L41_BSTCVRT_COEFF		0x00003810
+#define CS35L41_BSTCVRT_SLOPE_LBST	0x00003814
+#define CS35L41_BSTCVRT_SW_FREQ		0x00003818
+#define CS35L41_BSTCVRT_DCM_CTRL	0x0000381C
+#define CS35L41_BSTCVRT_DCM_MODE_FORCE	0x00003820
+#define CS35L41_BSTCVRT_OVERVOLT_CTRL	0x00003830
+#define CS35L41_VI_VOL_POL		0x00004000
+#define CS35L41_VIMON_SPKMON_RESYNC	0x00004100
+#define CS35L41_DTEMP_WARN_THLD		0x00004220
+#define CS35L41_DTEMP_CFG		0x00004224
+#define CS35L41_DTEMP_EN		0x00004308
+#define CS35L41_VPVBST_FS_SEL		0x00004400
+#define CS35L41_SP_ENABLES		0x00004800
+#define CS35L41_SP_RATE_CTRL		0x00004804
+#define CS35L41_SP_FORMAT		0x00004808
+#define CS35L41_SP_HIZ_CTRL		0x0000480C
+#define CS35L41_SP_FRAME_TX_SLOT	0x00004810
+#define CS35L41_SP_FRAME_RX_SLOT	0x00004820
+#define CS35L41_SP_TX_WL		0x00004830
+#define CS35L41_SP_RX_WL		0x00004840
+#define CS35L41_ASP_CONTROL4		0x00004854
+#define CS35L41_DAC_PCM1_SRC		0x00004C00
+#define CS35L41_ASP_TX1_SRC		0x00004C20
+#define CS35L41_ASP_TX2_SRC		0x00004C24
+#define CS35L41_ASP_TX3_SRC		0x00004C28
+#define CS35L41_ASP_TX4_SRC		0x00004C2C
+#define CS35L41_DSP1_RX1_SRC		0x00004C40
+#define CS35L41_DSP1_RX2_SRC		0x00004C44
+#define CS35L41_DSP1_RX3_SRC		0x00004C48
+#define CS35L41_DSP1_RX4_SRC		0x00004C4C
+#define CS35L41_DSP1_RX5_SRC		0x00004C50
+#define CS35L41_DSP1_RX6_SRC		0x00004C54
+#define CS35L41_DSP1_RX7_SRC		0x00004C58
+#define CS35L41_DSP1_RX8_SRC		0x00004C5C
+#define CS35L41_NGATE1_SRC		0x00004C60
+#define CS35L41_NGATE2_SRC		0x00004C64
+#define CS35L41_AMP_DIG_VOL_CTRL	0x00006000
+#define CS35L41_VPBR_CFG		0x00006404
+#define CS35L41_VBBR_CFG		0x00006408
+#define CS35L41_VPBR_STATUS		0x0000640C
+#define CS35L41_VBBR_STATUS		0x00006410
+#define CS35L41_OVERTEMP_CFG		0x00006414
+#define CS35L41_AMP_ERR_VOL		0x00006418
+#define CS35L41_VOL_STATUS_TO_DSP	0x00006450
+#define CS35L41_CLASSH_CFG		0x00006800
+#define CS35L41_WKFET_CFG		0x00006804
+#define CS35L41_NG_CFG			0x00006808
+#define CS35L41_AMP_GAIN_CTRL		0x00006C04
+#define CS35L41_DAC_MSM_CFG		0x00007400
+#define CS35L41_IRQ1_CFG		0x00010000
+#define CS35L41_IRQ1_STATUS		0x00010004
+#define CS35L41_IRQ1_STATUS1		0x00010010
+#define CS35L41_IRQ1_STATUS2		0x00010014
+#define CS35L41_IRQ1_STATUS3		0x00010018
+#define CS35L41_IRQ1_STATUS4		0x0001001C
+#define CS35L41_IRQ1_RAW_STATUS1	0x00010090
+#define CS35L41_IRQ1_RAW_STATUS2	0x00010094
+#define CS35L41_IRQ1_RAW_STATUS3	0x00010098
+#define CS35L41_IRQ1_RAW_STATUS4	0x0001009C
+#define CS35L41_IRQ1_MASK1		0x00010110
+#define CS35L41_IRQ1_MASK2		0x00010114
+#define CS35L41_IRQ1_MASK3		0x00010118
+#define CS35L41_IRQ1_MASK4		0x0001011C
+#define CS35L41_IRQ1_FRC1		0x00010190
+#define CS35L41_IRQ1_FRC2		0x00010194
+#define CS35L41_IRQ1_FRC3		0x00010198
+#define CS35L41_IRQ1_FRC4		0x0001019C
+#define CS35L41_IRQ1_EDGE1		0x00010210
+#define CS35L41_IRQ1_EDGE4		0x0001021C
+#define CS35L41_IRQ1_POL1		0x00010290
+#define CS35L41_IRQ1_POL2		0x00010294
+#define CS35L41_IRQ1_POL3		0x00010298
+#define CS35L41_IRQ1_POL4		0x0001029C
+#define CS35L41_IRQ1_DB3		0x00010318
+#define CS35L41_IRQ2_CFG		0x00010800
+#define CS35L41_IRQ2_STATUS		0x00010804
+#define CS35L41_IRQ2_STATUS1		0x00010810
+#define CS35L41_IRQ2_STATUS2		0x00010814
+#define CS35L41_IRQ2_STATUS3		0x00010818
+#define CS35L41_IRQ2_STATUS4		0x0001081C
+#define CS35L41_IRQ2_RAW_STATUS1	0x00010890
+#define CS35L41_IRQ2_RAW_STATUS2	0x00010894
+#define CS35L41_IRQ2_RAW_STATUS3	0x00010898
+#define CS35L41_IRQ2_RAW_STATUS4	0x0001089C
+#define CS35L41_IRQ2_MASK1		0x00010910
+#define CS35L41_IRQ2_MASK2		0x00010914
+#define CS35L41_IRQ2_MASK3		0x00010918
+#define CS35L41_IRQ2_MASK4		0x0001091C
+#define CS35L41_IRQ2_FRC1		0x00010990
+#define CS35L41_IRQ2_FRC2		0x00010994
+#define CS35L41_IRQ2_FRC3		0x00010998
+#define CS35L41_IRQ2_FRC4		0x0001099C
+#define CS35L41_IRQ2_EDGE1		0x00010A10
+#define CS35L41_IRQ2_EDGE4		0x00010A1C
+#define CS35L41_IRQ2_POL1		0x00010A90
+#define CS35L41_IRQ2_POL2		0x00010A94
+#define CS35L41_IRQ2_POL3		0x00010A98
+#define CS35L41_IRQ2_POL4		0x00010A9C
+#define CS35L41_IRQ2_DB3		0x00010B18
+#define CS35L41_GPIO_STATUS1		0x00011000
+#define CS35L41_GPIO1_CTRL1		0x00011008
+#define CS35L41_GPIO2_CTRL1		0x0001100C
+#define CS35L41_MIXER_NGATE_CFG		0x00012000
+#define CS35L41_MIXER_NGATE_CH1_CFG	0x00012004
+#define CS35L41_MIXER_NGATE_CH2_CFG	0x00012008
+#define CS35L41_DSP_MBOX_1		0x00013000
+#define CS35L41_DSP_MBOX_2		0x00013004
+#define CS35L41_DSP_MBOX_3		0x00013008
+#define CS35L41_DSP_MBOX_4		0x0001300C
+#define CS35L41_DSP_MBOX_5		0x00013010
+#define CS35L41_DSP_MBOX_6		0x00013014
+#define CS35L41_DSP_MBOX_7		0x00013018
+#define CS35L41_DSP_MBOX_8		0x0001301C
+#define CS35L41_DSP_VIRT1_MBOX_1	0x00013020
+#define CS35L41_DSP_VIRT1_MBOX_2	0x00013024
+#define CS35L41_DSP_VIRT1_MBOX_3	0x00013028
+#define CS35L41_DSP_VIRT1_MBOX_4	0x0001302C
+#define CS35L41_DSP_VIRT1_MBOX_5	0x00013030
+#define CS35L41_DSP_VIRT1_MBOX_6	0x00013034
+#define CS35L41_DSP_VIRT1_MBOX_7	0x00013038
+#define CS35L41_DSP_VIRT1_MBOX_8	0x0001303C
+#define CS35L41_DSP_VIRT2_MBOX_1	0x00013040
+#define CS35L41_DSP_VIRT2_MBOX_2	0x00013044
+#define CS35L41_DSP_VIRT2_MBOX_3	0x00013048
+#define CS35L41_DSP_VIRT2_MBOX_4	0x0001304C
+#define CS35L41_DSP_VIRT2_MBOX_5	0x00013050
+#define CS35L41_DSP_VIRT2_MBOX_6	0x00013054
+#define CS35L41_DSP_VIRT2_MBOX_7	0x00013058
+#define CS35L41_DSP_VIRT2_MBOX_8	0x0001305C
+#define CS35L41_CLOCK_DETECT_1		0x00014000
+#define CS35L41_TIMER1_CONTROL		0x00015000
+#define CS35L41_TIMER1_COUNT_PRESET	0x00015004
+#define CS35L41_TIMER1_START_STOP	0x0001500C
+#define CS35L41_TIMER1_STATUS		0x00015010
+#define CS35L41_TIMER1_COUNT_READBACK	0x00015014
+#define CS35L41_TIMER1_DSP_CLK_CFG	0x00015018
+#define CS35L41_TIMER1_DSP_CLK_STATUS	0x0001501C
+#define CS35L41_TIMER2_CONTROL		0x00015100
+#define CS35L41_TIMER2_COUNT_PRESET	0x00015104
+#define CS35L41_TIMER2_START_STOP	0x0001510C
+#define CS35L41_TIMER2_STATUS		0x00015110
+#define CS35L41_TIMER2_COUNT_READBACK	0x00015114
+#define CS35L41_TIMER2_DSP_CLK_CFG	0x00015118
+#define CS35L41_TIMER2_DSP_CLK_STATUS	0x0001511C
+#define CS35L41_DFT_JTAG_CONTROL	0x00016000
+#define CS35L41_DIE_STS1		0x00017040
+#define CS35L41_DIE_STS2		0x00017044
+#define CS35L41_TEMP_CAL1		0x00017048
+#define CS35L41_TEMP_CAL2		0x0001704C
+#define CS35L41_DSP1_XMEM_PACK_0	0x02000000
+#define CS35L41_DSP1_XMEM_PACK_3068	0x02002FF0
+#define CS35L41_DSP1_XMEM_UNPACK32_0	0x02400000
+#define CS35L41_DSP1_XMEM_UNPACK32_2046	0x02401FF8
+#define CS35L41_DSP1_TIMESTAMP_COUNT	0x025C0800
+#define CS35L41_DSP1_SYS_ID		0x025E0000
+#define CS35L41_DSP1_SYS_VERSION	0x025E0004
+#define CS35L41_DSP1_SYS_CORE_ID	0x025E0008
+#define CS35L41_DSP1_SYS_AHB_ADDR	0x025E000C
+#define CS35L41_DSP1_SYS_XSRAM_SIZE	0x025E0010
+#define CS35L41_DSP1_SYS_YSRAM_SIZE	0x025E0018
+#define CS35L41_DSP1_SYS_PSRAM_SIZE	0x025E0020
+#define CS35L41_DSP1_SYS_PM_BOOT_SIZE	0x025E0028
+#define CS35L41_DSP1_SYS_FEATURES	0x025E002C
+#define CS35L41_DSP1_SYS_FIR_FILTERS	0x025E0030
+#define CS35L41_DSP1_SYS_LMS_FILTERS	0x025E0034
+#define CS35L41_DSP1_SYS_XM_BANK_SIZE	0x025E0038
+#define CS35L41_DSP1_SYS_YM_BANK_SIZE	0x025E003C
+#define CS35L41_DSP1_SYS_PM_BANK_SIZE	0x025E0040
+#define CS35L41_DSP1_AHBM_WIN0_CTRL0	0x025E2000
+#define CS35L41_DSP1_AHBM_WIN0_CTRL1	0x025E2004
+#define CS35L41_DSP1_AHBM_WIN1_CTRL0	0x025E2008
+#define CS35L41_DSP1_AHBM_WIN1_CTRL1	0x025E200C
+#define CS35L41_DSP1_AHBM_WIN2_CTRL0	0x025E2010
+#define CS35L41_DSP1_AHBM_WIN2_CTRL1	0x025E2014
+#define CS35L41_DSP1_AHBM_WIN3_CTRL0	0x025E2018
+#define CS35L41_DSP1_AHBM_WIN3_CTRL1	0x025E201C
+#define CS35L41_DSP1_AHBM_WIN4_CTRL0	0x025E2020
+#define CS35L41_DSP1_AHBM_WIN4_CTRL1	0x025E2024
+#define CS35L41_DSP1_AHBM_WIN5_CTRL0	0x025E2028
+#define CS35L41_DSP1_AHBM_WIN5_CTRL1	0x025E202C
+#define CS35L41_DSP1_AHBM_WIN6_CTRL0	0x025E2030
+#define CS35L41_DSP1_AHBM_WIN6_CTRL1	0x025E2034
+#define CS35L41_DSP1_AHBM_WIN7_CTRL0	0x025E2038
+#define CS35L41_DSP1_AHBM_WIN7_CTRL1	0x025E203C
+#define CS35L41_DSP1_AHBM_WIN_DBG_CTRL0	0x025E2040
+#define CS35L41_DSP1_AHBM_WIN_DBG_CTRL1	0x025E2044
+#define CS35L41_DSP1_XMEM_UNPACK24_0	0x02800000
+#define CS35L41_DSP1_XMEM_UNPACK24_4093	0x02803FF4
+#define CS35L41_DSP1_CTRL_BASE		0x02B80000
+#define CS35L41_DSP1_CORE_SOFT_RESET	0x02B80010
+#define CS35L41_DSP1_DEBUG		0x02B80040
+#define CS35L41_DSP1_TIMER_CTRL		0x02B80048
+#define CS35L41_DSP1_STREAM_ARB_CTRL	0x02B80050
+#define CS35L41_DSP1_RX1_RATE		0x02B80080
+#define CS35L41_DSP1_RX2_RATE		0x02B80088
+#define CS35L41_DSP1_RX3_RATE		0x02B80090
+#define CS35L41_DSP1_RX4_RATE		0x02B80098
+#define CS35L41_DSP1_RX5_RATE		0x02B800A0
+#define CS35L41_DSP1_RX6_RATE		0x02B800A8
+#define CS35L41_DSP1_RX7_RATE		0x02B800B0
+#define CS35L41_DSP1_RX8_RATE		0x02B800B8
+#define CS35L41_DSP1_TX1_RATE		0x02B80280
+#define CS35L41_DSP1_TX2_RATE		0x02B80288
+#define CS35L41_DSP1_TX3_RATE		0x02B80290
+#define CS35L41_DSP1_TX4_RATE		0x02B80298
+#define CS35L41_DSP1_TX5_RATE		0x02B802A0
+#define CS35L41_DSP1_TX6_RATE		0x02B802A8
+#define CS35L41_DSP1_TX7_RATE		0x02B802B0
+#define CS35L41_DSP1_TX8_RATE		0x02B802B8
+#define CS35L41_DSP1_NMI_CTRL1		0x02B80480
+#define CS35L41_DSP1_NMI_CTRL2		0x02B80488
+#define CS35L41_DSP1_NMI_CTRL3		0x02B80490
+#define CS35L41_DSP1_NMI_CTRL4		0x02B80498
+#define CS35L41_DSP1_NMI_CTRL5		0x02B804A0
+#define CS35L41_DSP1_NMI_CTRL6		0x02B804A8
+#define CS35L41_DSP1_NMI_CTRL7		0x02B804B0
+#define CS35L41_DSP1_NMI_CTRL8		0x02B804B8
+#define CS35L41_DSP1_RESUME_CTRL	0x02B80500
+#define CS35L41_DSP1_IRQ1_CTRL		0x02B80508
+#define CS35L41_DSP1_IRQ2_CTRL		0x02B80510
+#define CS35L41_DSP1_IRQ3_CTRL		0x02B80518
+#define CS35L41_DSP1_IRQ4_CTRL		0x02B80520
+#define CS35L41_DSP1_IRQ5_CTRL		0x02B80528
+#define CS35L41_DSP1_IRQ6_CTRL		0x02B80530
+#define CS35L41_DSP1_IRQ7_CTRL		0x02B80538
+#define CS35L41_DSP1_IRQ8_CTRL		0x02B80540
+#define CS35L41_DSP1_IRQ9_CTRL		0x02B80548
+#define CS35L41_DSP1_IRQ10_CTRL		0x02B80550
+#define CS35L41_DSP1_IRQ11_CTRL		0x02B80558
+#define CS35L41_DSP1_IRQ12_CTRL		0x02B80560
+#define CS35L41_DSP1_IRQ13_CTRL		0x02B80568
+#define CS35L41_DSP1_IRQ14_CTRL		0x02B80570
+#define CS35L41_DSP1_IRQ15_CTRL		0x02B80578
+#define CS35L41_DSP1_IRQ16_CTRL		0x02B80580
+#define CS35L41_DSP1_IRQ17_CTRL		0x02B80588
+#define CS35L41_DSP1_IRQ18_CTRL		0x02B80590
+#define CS35L41_DSP1_IRQ19_CTRL		0x02B80598
+#define CS35L41_DSP1_IRQ20_CTRL		0x02B805A0
+#define CS35L41_DSP1_IRQ21_CTRL		0x02B805A8
+#define CS35L41_DSP1_IRQ22_CTRL		0x02B805B0
+#define CS35L41_DSP1_IRQ23_CTRL		0x02B805B8
+#define CS35L41_DSP1_SCRATCH1		0x02B805C0
+#define CS35L41_DSP1_SCRATCH2		0x02B805C8
+#define CS35L41_DSP1_SCRATCH3		0x02B805D0
+#define CS35L41_DSP1_SCRATCH4		0x02B805D8
+#define CS35L41_DSP1_CCM_CORE_CTRL	0x02BC1000
+#define CS35L41_DSP1_CCM_CLK_OVERRIDE	0x02BC1008
+#define CS35L41_DSP1_XM_MSTR_EN		0x02BC2000
+#define CS35L41_DSP1_XM_CORE_PRI	0x02BC2008
+#define CS35L41_DSP1_XM_AHB_PACK_PL_PRI	0x02BC2010
+#define CS35L41_DSP1_XM_AHB_UP_PL_PRI	0x02BC2018
+#define CS35L41_DSP1_XM_ACCEL_PL0_PRI	0x02BC2020
+#define CS35L41_DSP1_XM_NPL0_PRI	0x02BC2078
+#define CS35L41_DSP1_YM_MSTR_EN		0x02BC20C0
+#define CS35L41_DSP1_YM_CORE_PRI	0x02BC20C8
+#define CS35L41_DSP1_YM_AHB_PACK_PL_PRI	0x02BC20D0
+#define CS35L41_DSP1_YM_AHB_UP_PL_PRI	0x02BC20D8
+#define CS35L41_DSP1_YM_ACCEL_PL0_PRI	0x02BC20E0
+#define CS35L41_DSP1_YM_NPL0_PRI	0x02BC2138
+#define CS35L41_DSP1_PM_MSTR_EN		0x02BC2180
+#define CS35L41_DSP1_PM_PATCH0_ADDR	0x02BC2188
+#define CS35L41_DSP1_PM_PATCH0_EN	0x02BC218C
+#define CS35L41_DSP1_PM_PATCH0_DATA_LO	0x02BC2190
+#define CS35L41_DSP1_PM_PATCH0_DATA_HI	0x02BC2194
+#define CS35L41_DSP1_PM_PATCH1_ADDR	0x02BC2198
+#define CS35L41_DSP1_PM_PATCH1_EN	0x02BC219C
+#define CS35L41_DSP1_PM_PATCH1_DATA_LO	0x02BC21A0
+#define CS35L41_DSP1_PM_PATCH1_DATA_HI	0x02BC21A4
+#define CS35L41_DSP1_PM_PATCH2_ADDR	0x02BC21A8
+#define CS35L41_DSP1_PM_PATCH2_EN	0x02BC21AC
+#define CS35L41_DSP1_PM_PATCH2_DATA_LO	0x02BC21B0
+#define CS35L41_DSP1_PM_PATCH2_DATA_HI	0x02BC21B4
+#define CS35L41_DSP1_PM_PATCH3_ADDR	0x02BC21B8
+#define CS35L41_DSP1_PM_PATCH3_EN	0x02BC21BC
+#define CS35L41_DSP1_PM_PATCH3_DATA_LO	0x02BC21C0
+#define CS35L41_DSP1_PM_PATCH3_DATA_HI	0x02BC21C4
+#define CS35L41_DSP1_PM_PATCH4_ADDR	0x02BC21C8
+#define CS35L41_DSP1_PM_PATCH4_EN	0x02BC21CC
+#define CS35L41_DSP1_PM_PATCH4_DATA_LO	0x02BC21D0
+#define CS35L41_DSP1_PM_PATCH4_DATA_HI	0x02BC21D4
+#define CS35L41_DSP1_PM_PATCH5_ADDR	0x02BC21D8
+#define CS35L41_DSP1_PM_PATCH5_EN	0x02BC21DC
+#define CS35L41_DSP1_PM_PATCH5_DATA_LO	0x02BC21E0
+#define CS35L41_DSP1_PM_PATCH5_DATA_HI	0x02BC21E4
+#define CS35L41_DSP1_PM_PATCH6_ADDR	0x02BC21E8
+#define CS35L41_DSP1_PM_PATCH6_EN	0x02BC21EC
+#define CS35L41_DSP1_PM_PATCH6_DATA_LO	0x02BC21F0
+#define CS35L41_DSP1_PM_PATCH6_DATA_HI	0x02BC21F4
+#define CS35L41_DSP1_PM_PATCH7_ADDR	0x02BC21F8
+#define CS35L41_DSP1_PM_PATCH7_EN	0x02BC21FC
+#define CS35L41_DSP1_PM_PATCH7_DATA_LO	0x02BC2200
+#define CS35L41_DSP1_PM_PATCH7_DATA_HI	0x02BC2204
+#define CS35L41_DSP1_MPU_XM_ACCESS0	0x02BC3000
+#define CS35L41_DSP1_MPU_YM_ACCESS0	0x02BC3004
+#define CS35L41_DSP1_MPU_WNDW_ACCESS0	0x02BC3008
+#define CS35L41_DSP1_MPU_XREG_ACCESS0	0x02BC300C
+#define CS35L41_DSP1_MPU_YREG_ACCESS0	0x02BC3014
+#define CS35L41_DSP1_MPU_XM_ACCESS1	0x02BC3018
+#define CS35L41_DSP1_MPU_YM_ACCESS1	0x02BC301C
+#define CS35L41_DSP1_MPU_WNDW_ACCESS1	0x02BC3020
+#define CS35L41_DSP1_MPU_XREG_ACCESS1	0x02BC3024
+#define CS35L41_DSP1_MPU_YREG_ACCESS1	0x02BC302C
+#define CS35L41_DSP1_MPU_XM_ACCESS2	0x02BC3030
+#define CS35L41_DSP1_MPU_YM_ACCESS2	0x02BC3034
+#define CS35L41_DSP1_MPU_WNDW_ACCESS2	0x02BC3038
+#define CS35L41_DSP1_MPU_XREG_ACCESS2	0x02BC303C
+#define CS35L41_DSP1_MPU_YREG_ACCESS2	0x02BC3044
+#define CS35L41_DSP1_MPU_XM_ACCESS3	0x02BC3048
+#define CS35L41_DSP1_MPU_YM_ACCESS3	0x02BC304C
+#define CS35L41_DSP1_MPU_WNDW_ACCESS3	0x02BC3050
+#define CS35L41_DSP1_MPU_XREG_ACCESS3	0x02BC3054
+#define CS35L41_DSP1_MPU_YREG_ACCESS3	0x02BC305C
+#define CS35L41_DSP1_MPU_XM_VIO_ADDR	0x02BC3100
+#define CS35L41_DSP1_MPU_XM_VIO_STATUS	0x02BC3104
+#define CS35L41_DSP1_MPU_YM_VIO_ADDR	0x02BC3108
+#define CS35L41_DSP1_MPU_YM_VIO_STATUS	0x02BC310C
+#define CS35L41_DSP1_MPU_PM_VIO_ADDR	0x02BC3110
+#define CS35L41_DSP1_MPU_PM_VIO_STATUS	0x02BC3114
+#define CS35L41_DSP1_MPU_LOCK_CONFIG	0x02BC3140
+#define CS35L41_DSP1_MPU_WDT_RST_CTRL	0x02BC3180
+#define CS35L41_DSP1_STRMARB_MSTR0_CFG0	0x02BC5000
+#define CS35L41_DSP1_STRMARB_MSTR0_CFG1	0x02BC5004
+#define CS35L41_DSP1_STRMARB_MSTR0_CFG2	0x02BC5008
+#define CS35L41_DSP1_STRMARB_MSTR1_CFG0	0x02BC5010
+#define CS35L41_DSP1_STRMARB_MSTR1_CFG1	0x02BC5014
+#define CS35L41_DSP1_STRMARB_MSTR1_CFG2	0x02BC5018
+#define CS35L41_DSP1_STRMARB_MSTR2_CFG0	0x02BC5020
+#define CS35L41_DSP1_STRMARB_MSTR2_CFG1	0x02BC5024
+#define CS35L41_DSP1_STRMARB_MSTR2_CFG2	0x02BC5028
+#define CS35L41_DSP1_STRMARB_MSTR3_CFG0	0x02BC5030
+#define CS35L41_DSP1_STRMARB_MSTR3_CFG1	0x02BC5034
+#define CS35L41_DSP1_STRMARB_MSTR3_CFG2	0x02BC5038
+#define CS35L41_DSP1_STRMARB_MSTR4_CFG0	0x02BC5040
+#define CS35L41_DSP1_STRMARB_MSTR4_CFG1	0x02BC5044
+#define CS35L41_DSP1_STRMARB_MSTR4_CFG2	0x02BC5048
+#define CS35L41_DSP1_STRMARB_MSTR5_CFG0	0x02BC5050
+#define CS35L41_DSP1_STRMARB_MSTR5_CFG1	0x02BC5054
+#define CS35L41_DSP1_STRMARB_MSTR5_CFG2	0x02BC5058
+#define CS35L41_DSP1_STRMARB_MSTR6_CFG0	0x02BC5060
+#define CS35L41_DSP1_STRMARB_MSTR6_CFG1	0x02BC5064
+#define CS35L41_DSP1_STRMARB_MSTR6_CFG2	0x02BC5068
+#define CS35L41_DSP1_STRMARB_MSTR7_CFG0	0x02BC5070
+#define CS35L41_DSP1_STRMARB_MSTR7_CFG1	0x02BC5074
+#define CS35L41_DSP1_STRMARB_MSTR7_CFG2	0x02BC5078
+#define CS35L41_DSP1_STRMARB_TX0_CFG0	0x02BC5200
+#define CS35L41_DSP1_STRMARB_TX0_CFG1	0x02BC5204
+#define CS35L41_DSP1_STRMARB_TX1_CFG0	0x02BC5208
+#define CS35L41_DSP1_STRMARB_TX1_CFG1	0x02BC520C
+#define CS35L41_DSP1_STRMARB_TX2_CFG0	0x02BC5210
+#define CS35L41_DSP1_STRMARB_TX2_CFG1	0x02BC5214
+#define CS35L41_DSP1_STRMARB_TX3_CFG0	0x02BC5218
+#define CS35L41_DSP1_STRMARB_TX3_CFG1	0x02BC521C
+#define CS35L41_DSP1_STRMARB_TX4_CFG0	0x02BC5220
+#define CS35L41_DSP1_STRMARB_TX4_CFG1	0x02BC5224
+#define CS35L41_DSP1_STRMARB_TX5_CFG0	0x02BC5228
+#define CS35L41_DSP1_STRMARB_TX5_CFG1	0x02BC522C
+#define CS35L41_DSP1_STRMARB_TX6_CFG0	0x02BC5230
+#define CS35L41_DSP1_STRMARB_TX6_CFG1	0x02BC5234
+#define CS35L41_DSP1_STRMARB_TX7_CFG0	0x02BC5238
+#define CS35L41_DSP1_STRMARB_TX7_CFG1	0x02BC523C
+#define CS35L41_DSP1_STRMARB_RX0_CFG0	0x02BC5400
+#define CS35L41_DSP1_STRMARB_RX0_CFG1	0x02BC5404
+#define CS35L41_DSP1_STRMARB_RX1_CFG0	0x02BC5408
+#define CS35L41_DSP1_STRMARB_RX1_CFG1	0x02BC540C
+#define CS35L41_DSP1_STRMARB_RX2_CFG0	0x02BC5410
+#define CS35L41_DSP1_STRMARB_RX2_CFG1	0x02BC5414
+#define CS35L41_DSP1_STRMARB_RX3_CFG0	0x02BC5418
+#define CS35L41_DSP1_STRMARB_RX3_CFG1	0x02BC541C
+#define CS35L41_DSP1_STRMARB_RX4_CFG0	0x02BC5420
+#define CS35L41_DSP1_STRMARB_RX4_CFG1	0x02BC5424
+#define CS35L41_DSP1_STRMARB_RX5_CFG0	0x02BC5428
+#define CS35L41_DSP1_STRMARB_RX5_CFG1	0x02BC542C
+#define CS35L41_DSP1_STRMARB_RX6_CFG0	0x02BC5430
+#define CS35L41_DSP1_STRMARB_RX6_CFG1	0x02BC5434
+#define CS35L41_DSP1_STRMARB_RX7_CFG0	0x02BC5438
+#define CS35L41_DSP1_STRMARB_RX7_CFG1	0x02BC543C
+#define CS35L41_DSP1_STRMARB_IRQ0_CFG0	0x02BC5600
+#define CS35L41_DSP1_STRMARB_IRQ0_CFG1	0x02BC5604
+#define CS35L41_DSP1_STRMARB_IRQ0_CFG2	0x02BC5608
+#define CS35L41_DSP1_STRMARB_IRQ1_CFG0	0x02BC5610
+#define CS35L41_DSP1_STRMARB_IRQ1_CFG1	0x02BC5614
+#define CS35L41_DSP1_STRMARB_IRQ1_CFG2	0x02BC5618
+#define CS35L41_DSP1_STRMARB_IRQ2_CFG0	0x02BC5620
+#define CS35L41_DSP1_STRMARB_IRQ2_CFG1	0x02BC5624
+#define CS35L41_DSP1_STRMARB_IRQ2_CFG2	0x02BC5628
+#define CS35L41_DSP1_STRMARB_IRQ3_CFG0	0x02BC5630
+#define CS35L41_DSP1_STRMARB_IRQ3_CFG1	0x02BC5634
+#define CS35L41_DSP1_STRMARB_IRQ3_CFG2	0x02BC5638
+#define CS35L41_DSP1_STRMARB_IRQ4_CFG0	0x02BC5640
+#define CS35L41_DSP1_STRMARB_IRQ4_CFG1	0x02BC5644
+#define CS35L41_DSP1_STRMARB_IRQ4_CFG2	0x02BC5648
+#define CS35L41_DSP1_STRMARB_IRQ5_CFG0	0x02BC5650
+#define CS35L41_DSP1_STRMARB_IRQ5_CFG1	0x02BC5654
+#define CS35L41_DSP1_STRMARB_IRQ5_CFG2	0x02BC5658
+#define CS35L41_DSP1_STRMARB_IRQ6_CFG0	0x02BC5660
+#define CS35L41_DSP1_STRMARB_IRQ6_CFG1	0x02BC5664
+#define CS35L41_DSP1_STRMARB_IRQ6_CFG2	0x02BC5668
+#define CS35L41_DSP1_STRMARB_IRQ7_CFG0	0x02BC5670
+#define CS35L41_DSP1_STRMARB_IRQ7_CFG1	0x02BC5674
+#define CS35L41_DSP1_STRMARB_IRQ7_CFG2	0x02BC5678
+#define CS35L41_DSP1_STRMARB_RESYNC_MSK	0x02BC5A00
+#define CS35L41_DSP1_STRMARB_ERR_STATUS	0x02BC5A08
+#define CS35L41_DSP1_INTPCTL_RES_STATIC	0x02BC6000
+#define CS35L41_DSP1_INTPCTL_RES_DYN	0x02BC6004
+#define CS35L41_DSP1_INTPCTL_NMI_CTRL	0x02BC6008
+#define CS35L41_DSP1_INTPCTL_IRQ_INV	0x02BC6010
+#define CS35L41_DSP1_INTPCTL_IRQ_MODE	0x02BC6014
+#define CS35L41_DSP1_INTPCTL_IRQ_EN	0x02BC6018
+#define CS35L41_DSP1_INTPCTL_IRQ_MSK	0x02BC601C
+#define CS35L41_DSP1_INTPCTL_IRQ_FLUSH	0x02BC6020
+#define CS35L41_DSP1_INTPCTL_IRQ_MSKCLR	0x02BC6024
+#define CS35L41_DSP1_INTPCTL_IRQ_FRC	0x02BC6028
+#define CS35L41_DSP1_INTPCTL_IRQ_MSKSET	0x02BC602C
+#define CS35L41_DSP1_INTPCTL_IRQ_ERR	0x02BC6030
+#define CS35L41_DSP1_INTPCTL_IRQ_PEND	0x02BC6034
+#define CS35L41_DSP1_INTPCTL_IRQ_GEN	0x02BC6038
+#define CS35L41_DSP1_INTPCTL_TESTBITS	0x02BC6040
+#define CS35L41_DSP1_WDT_CONTROL	0x02BC7000
+#define CS35L41_DSP1_WDT_STATUS		0x02BC7008
+#define CS35L41_DSP1_YMEM_PACK_0	0x02C00000
+#define CS35L41_DSP1_YMEM_PACK_1532	0x02C017F0
+#define CS35L41_DSP1_YMEM_UNPACK32_0	0x03000000
+#define CS35L41_DSP1_YMEM_UNPACK32_1022	0x03000FF8
+#define CS35L41_DSP1_YMEM_UNPACK24_0	0x03400000
+#define CS35L41_DSP1_YMEM_UNPACK24_2045	0x03401FF4
+#define CS35L41_DSP1_PMEM_0		0x03800000
+#define CS35L41_DSP1_PMEM_5114		0x03804FE8
+
+/*test regs for emulation bringup*/
+#define CS35L41_PLL_OVR			0x00003018
+#define CS35L41_BST_TEST_DUTY		0x00003900
+#define CS35L41_DIGPWM_IOCTRL		0x0000706C
+
+/*registers populated by OTP*/
+#define CS35L41_OTP_TRIM_1		0x0000208c
+#define CS35L41_OTP_TRIM_2		0x00002090
+#define CS35L41_OTP_TRIM_3		0x00003010
+#define CS35L41_OTP_TRIM_4		0x0000300C
+#define CS35L41_OTP_TRIM_5		0x0000394C
+#define CS35L41_OTP_TRIM_6		0x00003950
+#define CS35L41_OTP_TRIM_7		0x00003954
+#define CS35L41_OTP_TRIM_8		0x00003958
+#define CS35L41_OTP_TRIM_9		0x0000395C
+#define CS35L41_OTP_TRIM_10		0x0000416C
+#define CS35L41_OTP_TRIM_11		0x00004160
+#define CS35L41_OTP_TRIM_12		0x00004170
+#define CS35L41_OTP_TRIM_13		0x00004360
+#define CS35L41_OTP_TRIM_14		0x00004448
+#define CS35L41_OTP_TRIM_15		0x0000444C
+#define CS35L41_OTP_TRIM_16		0x00006E30
+#define CS35L41_OTP_TRIM_17		0x00006E34
+#define CS35L41_OTP_TRIM_18		0x00006E38
+#define CS35L41_OTP_TRIM_19		0x00006E3C
+#define CS35L41_OTP_TRIM_20		0x00006E40
+#define CS35L41_OTP_TRIM_21		0x00006E44
+#define CS35L41_OTP_TRIM_22		0x00006E48
+#define CS35L41_OTP_TRIM_23		0x00006E4C
+#define CS35L41_OTP_TRIM_24		0x00006E50
+#define CS35L41_OTP_TRIM_25		0x00006E54
+#define CS35L41_OTP_TRIM_26		0x00006E58
+#define CS35L41_OTP_TRIM_27		0x00006E5C
+#define CS35L41_OTP_TRIM_28		0x00006E60
+#define CS35L41_OTP_TRIM_29		0x00006E64
+#define CS35L41_OTP_TRIM_30		0x00007418
+#define CS35L41_OTP_TRIM_31		0x0000741C
+#define CS35L41_OTP_TRIM_32		0x00007434
+#define CS35L41_OTP_TRIM_33		0x00007068
+#define CS35L41_OTP_TRIM_34		0x0000410C
+#define CS35L41_OTP_TRIM_35		0x0000400C
+#define CS35L41_OTP_TRIM_36		0x00002030
+
+#define CS35L41_MAX_CACHE_REG		36
+#define CS35L41_OTP_SIZE_WORDS		32
+
+#define CS35L41_VALID_PDATA		0x80000000
+#define CS35L41_NUM_SUPPLIES            2
+
+#define CS35L41_SCLK_MSTR_MASK		0x10
+#define CS35L41_SCLK_MSTR_SHIFT		4
+#define CS35L41_LRCLK_MSTR_MASK		0x01
+#define CS35L41_LRCLK_MSTR_SHIFT	0
+#define CS35L41_SCLK_INV_MASK		0x40
+#define CS35L41_SCLK_INV_SHIFT		6
+#define CS35L41_LRCLK_INV_MASK		0x04
+#define CS35L41_LRCLK_INV_SHIFT		2
+#define CS35L41_SCLK_FRC_MASK		0x20
+#define CS35L41_SCLK_FRC_SHIFT		5
+#define CS35L41_LRCLK_FRC_MASK		0x02
+#define CS35L41_LRCLK_FRC_SHIFT		1
+
+#define CS35L41_AMP_GAIN_PCM_MASK	0x3E0
+#define CS35L41_AMP_GAIN_ZC_MASK	0x0400
+#define CS35L41_AMP_GAIN_ZC_SHIFT	10
+
+#define CS35L41_BST_CTL_MASK		0xFF
+#define CS35L41_BST_CTL_SEL_MASK	0x03
+#define CS35L41_BST_CTL_SEL_REG		0x00
+#define CS35L41_BST_CTL_SEL_CLASSH	0x01
+#define CS35L41_BST_IPK_MASK		0x7F
+#define CS35L41_BST_IPK_SHIFT		0
+#define CS35L41_BST_LIM_MASK		0x4
+#define CS35L41_BST_LIM_SHIFT		2
+#define CS35L41_BST_K1_MASK		0x000000FF
+#define CS35L41_BST_K1_SHIFT		0
+#define CS35L41_BST_K2_MASK		0x0000FF00
+#define CS35L41_BST_K2_SHIFT		8
+#define CS35L41_BST_SLOPE_MASK		0x0000FF00
+#define CS35L41_BST_SLOPE_SHIFT		8
+#define CS35L41_BST_LBST_VAL_MASK	0x00000003
+#define CS35L41_BST_LBST_VAL_SHIFT	0
+
+#define CS35L41_TEMP_THLD_MASK		0x03
+#define CS35L41_VMON_IMON_VOL_MASK	0x07FF07FF
+#define CS35L41_PDM_MODE_MASK		0x01
+#define CS35L41_PDM_MODE_SHIFT		0
+
+#define CS35L41_CH_MEM_DEPTH_MASK	0x07
+#define CS35L41_CH_MEM_DEPTH_SHIFT	0
+#define CS35L41_CH_HDRM_CTL_MASK	0x007F0000
+#define CS35L41_CH_HDRM_CTL_SHIFT	16
+#define CS35L41_CH_REL_RATE_MASK	0xFF00
+#define CS35L41_CH_REL_RATE_SHIFT	8
+#define CS35L41_CH_WKFET_DLY_MASK	0x001C
+#define CS35L41_CH_WKFET_DLY_SHIFT	2
+#define CS35L41_CH_WKFET_THLD_MASK	0x0F00
+#define CS35L41_CH_WKFET_THLD_SHIFT	8
+
+#define CS35L41_HW_NG_SEL_MASK		0x3F00
+#define CS35L41_HW_NG_SEL_SHIFT		8
+#define CS35L41_HW_NG_DLY_MASK		0x0070
+#define CS35L41_HW_NG_DLY_SHIFT		4
+#define CS35L41_HW_NG_THLD_MASK		0x0007
+#define CS35L41_HW_NG_THLD_SHIFT	0
+
+#define CS35L41_DSP_NG_ENABLE_MASK	0x00010000
+#define CS35L41_DSP_NG_ENABLE_SHIFT	16
+#define CS35L41_DSP_NG_THLD_MASK	0x7
+#define CS35L41_DSP_NG_THLD_SHIFT	0
+#define CS35L41_DSP_NG_DELAY_MASK	0x0F00
+#define CS35L41_DSP_NG_DELAY_SHIFT	8
+
+#define CS35L41_ASP_FMT_MASK		0x0700
+#define CS35L41_ASP_FMT_SHIFT		8
+#define CS35L41_ASP_DOUT_HIZ_MASK	0x03
+#define CS35L41_ASP_DOUT_HIZ_SHIFT	0
+#define CS35L41_ASP_WIDTH_16		0x10
+#define CS35L41_ASP_WIDTH_24		0x18
+#define CS35L41_ASP_WIDTH_32		0x20
+#define CS35L41_ASP_WIDTH_TX_MASK	0xFF0000
+#define CS35L41_ASP_WIDTH_TX_SHIFT	16
+#define CS35L41_ASP_WIDTH_RX_MASK	0xFF000000
+#define CS35L41_ASP_WIDTH_RX_SHIFT	24
+#define CS35L41_ASP_RX1_SLOT_MASK	0x3F
+#define CS35L41_ASP_RX1_SLOT_SHIFT	0
+#define CS35L41_ASP_RX2_SLOT_MASK	0x3F00
+#define CS35L41_ASP_RX2_SLOT_SHIFT	8
+#define CS35L41_ASP_RX_WL_MASK		0x3F
+#define CS35L41_ASP_TX_WL_MASK		0x3F
+#define CS35L41_ASP_RX_WL_SHIFT		0
+#define CS35L41_ASP_TX_WL_SHIFT		0
+#define CS35L41_ASP_SOURCE_MASK		0x7F
+
+#define CS35L41_INPUT_SRC_ASPRX1	0x08
+#define CS35L41_INPUT_SRC_ASPRX2	0x09
+#define CS35L41_INPUT_SRC_VMON		0x18
+#define CS35L41_INPUT_SRC_IMON		0x19
+#define CS35L41_INPUT_SRC_CLASSH	0x21
+#define CS35L41_INPUT_SRC_VPMON		0x28
+#define CS35L41_INPUT_SRC_VBSTMON	0x29
+#define CS35L41_INPUT_SRC_TEMPMON	0x3A
+#define CS35L41_INPUT_SRC_RSVD		0x3B
+#define CS35L41_INPUT_DSP_TX1		0x32
+#define CS35L41_INPUT_DSP_TX2		0x33
+
+#define CS35L41_WR_PEND_STS_MASK	0x2
+
+#define CS35L41_PLL_CLK_SEL_MASK	0x07
+#define CS35L41_PLL_CLK_SEL_SHIFT	0
+#define CS35L41_PLL_CLK_EN_MASK		0x10
+#define CS35L41_PLL_CLK_EN_SHIFT	4
+#define CS35L41_PLL_OPENLOOP_MASK	0x0800
+#define CS35L41_PLL_OPENLOOP_SHIFT	11
+#define CS35L41_PLLSRC_SCLK		0
+#define CS35L41_PLLSRC_LRCLK		1
+#define CS35L41_PLLSRC_SELF		3
+#define CS35L41_PLLSRC_PDMCLK		4
+#define CS35L41_PLLSRC_MCLK		5
+#define CS35L41_PLLSRC_SWIRE		7
+#define CS35L41_REFCLK_FREQ_MASK	0x7E0
+#define CS35L41_REFCLK_FREQ_SHIFT	5
+
+#define CS35L41_GLOBAL_FS_MASK		0x1F
+#define CS35L41_GLOBAL_FS_SHIFT		0
+
+#define CS35L41_GLOBAL_EN_MASK		0x01
+#define CS35L41_GLOBAL_EN_SHIFT		0
+#define CS35L41_BST_EN_MASK		0x0030
+#define CS35L41_BST_EN_SHIFT		4
+#define CS35L41_BST_EN_DEFAULT		0x2
+#define CS35L41_AMP_EN_SHIFT		0
+#define CS35L41_AMP_EN_MASK		1
+
+#define CS35L41_PDN_DONE_MASK		0x00800000
+#define CS35L41_PDN_DONE_SHIFT		23
+#define CS35L41_PUP_DONE_MASK		0x01000000
+#define CS35L41_PUP_DONE_SHIFT		24
+
+#define CS35L36_PUP_DONE_IRQ_UNMASK	0x5F
+#define CS35L36_PUP_DONE_IRQ_MASK	0xBF
+
+#define CS35L41_AMP_SHORT_ERR		0x80000000
+#define CS35L41_BST_SHORT_ERR		0x0100
+#define CS35L41_TEMP_WARN		0x8000
+#define CS35L41_TEMP_ERR		0x00020000
+#define CS35L41_BST_OVP_ERR		0x40
+#define CS35L41_BST_DCM_UVP_ERR		0x80
+#define CS35L41_OTP_BOOT_DONE		0x02
+#define CS35L41_PLL_UNLOCK		0x10
+#define CS35L41_OTP_BOOT_ERR		0x80000000
+
+#define CS35L41_AMP_SHORT_ERR_RLS	0x02
+#define CS35L41_BST_SHORT_ERR_RLS	0x04
+#define CS35L41_BST_OVP_ERR_RLS		0x08
+#define CS35L41_BST_UVP_ERR_RLS		0x10
+#define CS35L41_TEMP_WARN_ERR_RLS	0x20
+#define CS35L41_TEMP_ERR_RLS		0x40
+
+#define CS35L41_INT1_MASK_DEFAULT	0x7FFCFE3F
+#define CS35L41_INT1_UNMASK_PUP		0xFEFFFFFF
+#define CS35L41_INT1_UNMASK_PDN		0xFF7FFFFF
+
+#define CS35L41_GPIO_DIR_MASK		0x80000000
+#define CS35L41_GPIO_DIR_SHIFT		31
+#define CS35L41_GPIO1_CTRL_MASK		0x00030000
+#define CS35L41_GPIO1_CTRL_SHIFT	16
+#define CS35L41_GPIO2_CTRL_MASK		0x07000000
+#define CS35L41_GPIO2_CTRL_SHIFT	24
+#define CS35L41_GPIO_CTRL_OPEN_INT	2
+#define CS35L41_GPIO_CTRL_ACTV_LO	4
+#define CS35L41_GPIO_CTRL_ACTV_HI	5
+#define CS35L41_GPIO_POL_MASK		0x1000
+#define CS35L41_GPIO_POL_SHIFT		12
+
+#define CS35L41_AMP_INV_PCM_SHIFT	14
+#define CS35L41_AMP_INV_PCM_MASK	BIT(CS35L41_AMP_INV_PCM_SHIFT)
+#define CS35L41_AMP_PCM_VOL_SHIFT	3
+#define CS35L41_AMP_PCM_VOL_MASK	(0x7FF << 3)
+#define CS35L41_AMP_PCM_VOL_MUTE	0x4CF
+
+#define CS35L41_CHIP_ID			0x35a40
+#define CS35L41R_CHIP_ID		0x35b40
+#define CS35L41_MTLREVID_MASK		0x0F
+#define CS35L41_REVID_A0		0xA0
+#define CS35L41_REVID_B0		0xB0
+#define CS35L41_REVID_B2		0xB2
+
+#define CS35L41_HALO_CORE_RESET		0x00000200
+
+#define CS35L41_FS1_WINDOW_MASK		0x000007FF
+#define CS35L41_FS2_WINDOW_MASK		0x00FFF800
+#define CS35L41_FS2_WINDOW_SHIFT	12
+
+#define CS35L41_SPI_MAX_FREQ		4000000
+#define CS35L41_REGSTRIDE		4
+
+enum cs35l41_clk_ids {
+	CS35L41_CLKID_SCLK = 0,
+	CS35L41_CLKID_LRCLK = 1,
+	CS35L41_CLKID_MCLK = 4,
+};
+
+struct cs35l41_irq_cfg {
+	bool irq_pol_inv;
+	bool irq_out_en;
+	int irq_src_sel;
+};
+
+struct cs35l41_platform_data {
+	int bst_ind;
+	int bst_ipk;
+	int bst_cap;
+	int dout_hiz;
+	struct cs35l41_irq_cfg irq_config1;
+	struct cs35l41_irq_cfg irq_config2;
+};
+
+struct cs35l41_otp_packed_element_t {
+	u32 reg;
+	u8 shift;
+	u8 size;
+};
+
+struct cs35l41_otp_map_element_t {
+	u32 id;
+	u32 num_elements;
+	const struct cs35l41_otp_packed_element_t *map;
+	u32 bit_offset;
+	u32 word_offset;
+};
+
+extern struct regmap_config cs35l41_regmap_i2c;
+extern struct regmap_config cs35l41_regmap_spi;
+
+int cs35l41_test_key_unlock(struct device *dev, struct regmap *regmap);
+int cs35l41_test_key_lock(struct device *dev, struct regmap *regmap);
+int cs35l41_otp_unpack(struct device *dev, struct regmap *regmap);
+int cs35l41_register_errata_patch(struct device *dev, struct regmap *reg, unsigned int reg_revid);
+int cs35l41_set_channels(struct device *dev, struct regmap *reg,
+			 unsigned int tx_num, unsigned int *tx_slot,
+			 unsigned int rx_num, unsigned int *rx_slot);
+int cs35l41_boost_config(struct device *dev, struct regmap *regmap, int boost_ind, int boost_cap,
+			 int boost_ipk);
+
+#endif /* __CS35L41_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/cs42l42.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/cs42l42.h
@@ -0,0 +1,810 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * linux/sound/cs42l42.h -- Platform data for CS42L42 ALSA SoC audio driver header
+ *
+ * Copyright 2016-2022 Cirrus Logic, Inc.
+ *
+ * Author: James Schulman <james.schulman@cirrus.com>
+ * Author: Brian Austin <brian.austin@cirrus.com>
+ * Author: Michael White <michael.white@cirrus.com>
+ */
+
+#ifndef __CS42L42_H
+#define __CS42L42_H
+
+#define CS42L42_PAGE_REGISTER	0x00	/* Page Select Register */
+#define CS42L42_WIN_START	0x00
+#define CS42L42_WIN_LEN		0x100
+#define CS42L42_RANGE_MIN	0x00
+#define CS42L42_RANGE_MAX	0x7F
+
+#define CS42L42_PAGE_10		0x1000
+#define CS42L42_PAGE_11		0x1100
+#define CS42L42_PAGE_12		0x1200
+#define CS42L42_PAGE_13		0x1300
+#define CS42L42_PAGE_15		0x1500
+#define CS42L42_PAGE_19		0x1900
+#define CS42L42_PAGE_1B		0x1B00
+#define CS42L42_PAGE_1C		0x1C00
+#define CS42L42_PAGE_1D		0x1D00
+#define CS42L42_PAGE_1F		0x1F00
+#define CS42L42_PAGE_20		0x2000
+#define CS42L42_PAGE_21		0x2100
+#define CS42L42_PAGE_23		0x2300
+#define CS42L42_PAGE_24		0x2400
+#define CS42L42_PAGE_25		0x2500
+#define CS42L42_PAGE_26		0x2600
+#define CS42L42_PAGE_28		0x2800
+#define CS42L42_PAGE_29		0x2900
+#define CS42L42_PAGE_2A		0x2A00
+#define CS42L42_PAGE_30		0x3000
+
+#define CS42L42_CHIP_ID		0x42A42
+
+/* Page 0x10 Global Registers */
+#define CS42L42_DEVID_AB		(CS42L42_PAGE_10 + 0x01)
+#define CS42L42_DEVID_CD		(CS42L42_PAGE_10 + 0x02)
+#define CS42L42_DEVID_E			(CS42L42_PAGE_10 + 0x03)
+#define CS42L42_FABID			(CS42L42_PAGE_10 + 0x04)
+#define CS42L42_REVID			(CS42L42_PAGE_10 + 0x05)
+#define CS42L42_FRZ_CTL			(CS42L42_PAGE_10 + 0x06)
+
+#define CS42L42_SRC_CTL			(CS42L42_PAGE_10 + 0x07)
+#define CS42L42_SRC_BYPASS_DAC_SHIFT	1
+#define CS42L42_SRC_BYPASS_DAC_MASK	(1 << CS42L42_SRC_BYPASS_DAC_SHIFT)
+
+#define CS42L42_MCLK_STATUS		(CS42L42_PAGE_10 + 0x08)
+
+#define CS42L42_MCLK_CTL		(CS42L42_PAGE_10 + 0x09)
+#define CS42L42_INTERNAL_FS_SHIFT	1
+#define CS42L42_INTERNAL_FS_MASK	(1 << CS42L42_INTERNAL_FS_SHIFT)
+
+#define CS42L42_SFTRAMP_RATE		(CS42L42_PAGE_10 + 0x0A)
+#define CS42L42_SLOW_START_ENABLE	(CS42L42_PAGE_10 + 0x0B)
+#define CS42L42_SLOW_START_EN_MASK	GENMASK(6, 4)
+#define CS42L42_SLOW_START_EN_SHIFT	4
+#define CS42L42_I2C_DEBOUNCE		(CS42L42_PAGE_10 + 0x0E)
+#define CS42L42_I2C_STRETCH		(CS42L42_PAGE_10 + 0x0F)
+#define CS42L42_I2C_TIMEOUT		(CS42L42_PAGE_10 + 0x10)
+
+/* Page 0x11 Power and Headset Detect Registers */
+#define CS42L42_PWR_CTL1		(CS42L42_PAGE_11 + 0x01)
+#define CS42L42_ASP_DAO_PDN_SHIFT	7
+#define CS42L42_ASP_DAO_PDN_MASK	(1 << CS42L42_ASP_DAO_PDN_SHIFT)
+#define CS42L42_ASP_DAI_PDN_SHIFT	6
+#define CS42L42_ASP_DAI_PDN_MASK	(1 << CS42L42_ASP_DAI_PDN_SHIFT)
+#define CS42L42_MIXER_PDN_SHIFT		5
+#define CS42L42_MIXER_PDN_MASK		(1 << CS42L42_MIXER_PDN_SHIFT)
+#define CS42L42_EQ_PDN_SHIFT		4
+#define CS42L42_EQ_PDN_MASK		(1 << CS42L42_EQ_PDN_SHIFT)
+#define CS42L42_HP_PDN_SHIFT		3
+#define CS42L42_HP_PDN_MASK		(1 << CS42L42_HP_PDN_SHIFT)
+#define CS42L42_ADC_PDN_SHIFT		2
+#define CS42L42_ADC_PDN_MASK		(1 << CS42L42_ADC_PDN_SHIFT)
+#define CS42L42_PDN_ALL_SHIFT		0
+#define CS42L42_PDN_ALL_MASK		(1 << CS42L42_PDN_ALL_SHIFT)
+
+#define CS42L42_PWR_CTL2		(CS42L42_PAGE_11 + 0x02)
+#define CS42L42_ADC_SRC_PDNB_SHIFT	0
+#define CS42L42_ADC_SRC_PDNB_MASK	(1 << CS42L42_ADC_SRC_PDNB_SHIFT)
+#define CS42L42_DAC_SRC_PDNB_SHIFT	1
+#define CS42L42_DAC_SRC_PDNB_MASK	(1 << CS42L42_DAC_SRC_PDNB_SHIFT)
+#define CS42L42_ASP_DAI1_PDN_SHIFT	2
+#define CS42L42_ASP_DAI1_PDN_MASK	(1 << CS42L42_ASP_DAI1_PDN_SHIFT)
+#define CS42L42_SRC_PDN_OVERRIDE_SHIFT	3
+#define CS42L42_SRC_PDN_OVERRIDE_MASK	(1 << CS42L42_SRC_PDN_OVERRIDE_SHIFT)
+#define CS42L42_DISCHARGE_FILT_SHIFT	4
+#define CS42L42_DISCHARGE_FILT_MASK	(1 << CS42L42_DISCHARGE_FILT_SHIFT)
+
+#define CS42L42_PWR_CTL3			(CS42L42_PAGE_11 + 0x03)
+#define CS42L42_RING_SENSE_PDNB_SHIFT		1
+#define CS42L42_RING_SENSE_PDNB_MASK		(1 << CS42L42_RING_SENSE_PDNB_SHIFT)
+#define CS42L42_VPMON_PDNB_SHIFT		2
+#define CS42L42_VPMON_PDNB_MASK			(1 << CS42L42_VPMON_PDNB_SHIFT)
+#define CS42L42_SW_CLK_STP_STAT_SEL_SHIFT	5
+#define CS42L42_SW_CLK_STP_STAT_SEL_MASK	(3 << CS42L42_SW_CLK_STP_STAT_SEL_SHIFT)
+
+#define CS42L42_RSENSE_CTL1			(CS42L42_PAGE_11 + 0x04)
+#define CS42L42_RS_TRIM_R_SHIFT			0
+#define CS42L42_RS_TRIM_R_MASK			(1 << CS42L42_RS_TRIM_R_SHIFT)
+#define CS42L42_RS_TRIM_T_SHIFT			1
+#define CS42L42_RS_TRIM_T_MASK			(1 << CS42L42_RS_TRIM_T_SHIFT)
+#define CS42L42_HPREF_RS_SHIFT			2
+#define CS42L42_HPREF_RS_MASK			(1 << CS42L42_HPREF_RS_SHIFT)
+#define CS42L42_HSBIAS_FILT_REF_RS_SHIFT	3
+#define CS42L42_HSBIAS_FILT_REF_RS_MASK		(1 << CS42L42_HSBIAS_FILT_REF_RS_SHIFT)
+#define CS42L42_RING_SENSE_PU_HIZ_SHIFT		6
+#define CS42L42_RING_SENSE_PU_HIZ_MASK		(1 << CS42L42_RING_SENSE_PU_HIZ_SHIFT)
+
+#define CS42L42_RSENSE_CTL2		(CS42L42_PAGE_11 + 0x05)
+#define CS42L42_TS_RS_GATE_SHIFT	7
+#define CS42L42_TS_RS_GATE_MAS		(1 << CS42L42_TS_RS_GATE_SHIFT)
+
+#define CS42L42_OSC_SWITCH		(CS42L42_PAGE_11 + 0x07)
+#define CS42L42_SCLK_PRESENT_SHIFT	0
+#define CS42L42_SCLK_PRESENT_MASK	(1 << CS42L42_SCLK_PRESENT_SHIFT)
+
+#define CS42L42_OSC_SWITCH_STATUS	(CS42L42_PAGE_11 + 0x09)
+#define CS42L42_OSC_SW_SEL_STAT_SHIFT	0
+#define CS42L42_OSC_SW_SEL_STAT_MASK	(3 << CS42L42_OSC_SW_SEL_STAT_SHIFT)
+#define CS42L42_OSC_PDNB_STAT_SHIFT	2
+#define CS42L42_OSC_PDNB_STAT_MASK	(1 << CS42L42_OSC_SW_SEL_STAT_SHIFT)
+
+#define CS42L42_RSENSE_CTL3			(CS42L42_PAGE_11 + 0x12)
+#define CS42L42_RS_RISE_DBNCE_TIME_SHIFT	0
+#define CS42L42_RS_RISE_DBNCE_TIME_MASK		(7 << CS42L42_RS_RISE_DBNCE_TIME_SHIFT)
+#define CS42L42_RS_FALL_DBNCE_TIME_SHIFT	3
+#define CS42L42_RS_FALL_DBNCE_TIME_MASK		(7 << CS42L42_RS_FALL_DBNCE_TIME_SHIFT)
+#define CS42L42_RS_PU_EN_SHIFT			6
+#define CS42L42_RS_PU_EN_MASK			(1 << CS42L42_RS_PU_EN_SHIFT)
+#define CS42L42_RS_INV_SHIFT			7
+#define CS42L42_RS_INV_MASK			(1 << CS42L42_RS_INV_SHIFT)
+
+#define CS42L42_TSENSE_CTL			(CS42L42_PAGE_11 + 0x13)
+#define CS42L42_TS_RISE_DBNCE_TIME_SHIFT	0
+#define CS42L42_TS_RISE_DBNCE_TIME_MASK		(7 << CS42L42_TS_RISE_DBNCE_TIME_SHIFT)
+#define CS42L42_TS_FALL_DBNCE_TIME_SHIFT	3
+#define CS42L42_TS_FALL_DBNCE_TIME_MASK		(7 << CS42L42_TS_FALL_DBNCE_TIME_SHIFT)
+#define CS42L42_TS_INV_SHIFT			7
+#define CS42L42_TS_INV_MASK			(1 << CS42L42_TS_INV_SHIFT)
+
+#define CS42L42_TSRS_INT_DISABLE	(CS42L42_PAGE_11 + 0x14)
+#define CS42L42_D_RS_PLUG_DBNC_SHIFT	0
+#define CS42L42_D_RS_PLUG_DBNC_MASK	(1 << CS42L42_D_RS_PLUG_DBNC_SHIFT)
+#define CS42L42_D_RS_UNPLUG_DBNC_SHIFT	1
+#define CS42L42_D_RS_UNPLUG_DBNC_MASK	(1 << CS42L42_D_RS_UNPLUG_DBNC_SHIFT)
+#define CS42L42_D_TS_PLUG_DBNC_SHIFT	2
+#define CS42L42_D_TS_PLUG_DBNC_MASK	(1 << CS42L42_D_TS_PLUG_DBNC_SHIFT)
+#define CS42L42_D_TS_UNPLUG_DBNC_SHIFT	3
+#define CS42L42_D_TS_UNPLUG_DBNC_MASK	(1 << CS42L42_D_TS_UNPLUG_DBNC_SHIFT)
+
+#define CS42L42_TRSENSE_STATUS		(CS42L42_PAGE_11 + 0x15)
+#define CS42L42_RS_PLUG_DBNC_SHIFT	0
+#define CS42L42_RS_PLUG_DBNC_MASK	(1 << CS42L42_RS_PLUG_DBNC_SHIFT)
+#define CS42L42_RS_UNPLUG_DBNC_SHIFT	1
+#define CS42L42_RS_UNPLUG_DBNC_MASK	(1 << CS42L42_RS_UNPLUG_DBNC_SHIFT)
+#define CS42L42_TS_PLUG_DBNC_SHIFT	2
+#define CS42L42_TS_PLUG_DBNC_MASK	(1 << CS42L42_TS_PLUG_DBNC_SHIFT)
+#define CS42L42_TS_UNPLUG_DBNC_SHIFT	3
+#define CS42L42_TS_UNPLUG_DBNC_MASK	(1 << CS42L42_TS_UNPLUG_DBNC_SHIFT)
+
+#define CS42L42_HSDET_CTL1		(CS42L42_PAGE_11 + 0x1F)
+#define CS42L42_HSDET_COMP1_LVL_SHIFT	0
+#define CS42L42_HSDET_COMP1_LVL_MASK	(15 << CS42L42_HSDET_COMP1_LVL_SHIFT)
+#define CS42L42_HSDET_COMP2_LVL_SHIFT	4
+#define CS42L42_HSDET_COMP2_LVL_MASK	(15 << CS42L42_HSDET_COMP2_LVL_SHIFT)
+
+#define CS42L42_HSDET_COMP1_LVL_VAL	12 /* 1.25V Comparator */
+#define CS42L42_HSDET_COMP2_LVL_VAL	2  /* 1.75V Comparator */
+#define CS42L42_HSDET_COMP1_LVL_DEFAULT	7  /* 1V Comparator */
+#define CS42L42_HSDET_COMP2_LVL_DEFAULT	7  /* 2V Comparator */
+
+#define CS42L42_HSDET_CTL2		(CS42L42_PAGE_11 + 0x20)
+#define CS42L42_HSDET_AUTO_TIME_SHIFT	0
+#define CS42L42_HSDET_AUTO_TIME_MASK	(3 << CS42L42_HSDET_AUTO_TIME_SHIFT)
+#define CS42L42_HSBIAS_REF_SHIFT	3
+#define CS42L42_HSBIAS_REF_MASK		(1 << CS42L42_HSBIAS_REF_SHIFT)
+#define CS42L42_HSDET_SET_SHIFT		4
+#define CS42L42_HSDET_SET_MASK		(3 << CS42L42_HSDET_SET_SHIFT)
+#define CS42L42_HSDET_CTRL_SHIFT	6
+#define CS42L42_HSDET_CTRL_MASK		(3 << CS42L42_HSDET_CTRL_SHIFT)
+
+#define CS42L42_HS_SWITCH_CTL		(CS42L42_PAGE_11 + 0x21)
+#define CS42L42_SW_GNDHS_HS4_SHIFT	0
+#define CS42L42_SW_GNDHS_HS4_MASK	(1 << CS42L42_SW_GNDHS_HS4_SHIFT)
+#define CS42L42_SW_GNDHS_HS3_SHIFT	1
+#define CS42L42_SW_GNDHS_HS3_MASK	(1 << CS42L42_SW_GNDHS_HS3_SHIFT)
+#define CS42L42_SW_HSB_HS4_SHIFT	2
+#define CS42L42_SW_HSB_HS4_MASK		(1 << CS42L42_SW_HSB_HS4_SHIFT)
+#define CS42L42_SW_HSB_HS3_SHIFT	3
+#define CS42L42_SW_HSB_HS3_MASK		(1 << CS42L42_SW_HSB_HS3_SHIFT)
+#define CS42L42_SW_HSB_FILT_HS4_SHIFT	4
+#define CS42L42_SW_HSB_FILT_HS4_MASK	(1 << CS42L42_SW_HSB_FILT_HS4_SHIFT)
+#define CS42L42_SW_HSB_FILT_HS3_SHIFT	5
+#define CS42L42_SW_HSB_FILT_HS3_MASK	(1 << CS42L42_SW_HSB_FILT_HS3_SHIFT)
+#define CS42L42_SW_REF_HS4_SHIFT	6
+#define CS42L42_SW_REF_HS4_MASK		(1 << CS42L42_SW_REF_HS4_SHIFT)
+#define CS42L42_SW_REF_HS3_SHIFT	7
+#define CS42L42_SW_REF_HS3_MASK		(1 << CS42L42_SW_REF_HS3_SHIFT)
+
+#define CS42L42_HS_DET_STATUS		(CS42L42_PAGE_11 + 0x24)
+#define CS42L42_HSDET_TYPE_SHIFT	0
+#define CS42L42_HSDET_TYPE_MASK		(3 << CS42L42_HSDET_TYPE_SHIFT)
+#define CS42L42_HSDET_COMP1_OUT_SHIFT	6
+#define CS42L42_HSDET_COMP1_OUT_MASK	(1 << CS42L42_HSDET_COMP1_OUT_SHIFT)
+#define CS42L42_HSDET_COMP2_OUT_SHIFT	7
+#define CS42L42_HSDET_COMP2_OUT_MASK	(1 << CS42L42_HSDET_COMP2_OUT_SHIFT)
+#define CS42L42_PLUG_CTIA		0
+#define CS42L42_PLUG_OMTP		1
+#define CS42L42_PLUG_HEADPHONE		2
+#define CS42L42_PLUG_INVALID		3
+
+#define CS42L42_HSDET_SW_COMP1		((0 << CS42L42_SW_GNDHS_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_GNDHS_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_FILT_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_REF_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS3_SHIFT))
+#define CS42L42_HSDET_SW_COMP2		((1 << CS42L42_SW_GNDHS_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_GNDHS_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_FILT_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_REF_HS3_SHIFT))
+#define CS42L42_HSDET_SW_TYPE1		((0 << CS42L42_SW_GNDHS_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_GNDHS_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_FILT_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_REF_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS3_SHIFT))
+#define CS42L42_HSDET_SW_TYPE2		((1 << CS42L42_SW_GNDHS_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_GNDHS_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_FILT_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_REF_HS3_SHIFT))
+#define CS42L42_HSDET_SW_TYPE3		((1 << CS42L42_SW_GNDHS_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_GNDHS_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS3_SHIFT))
+#define CS42L42_HSDET_SW_TYPE4		((0 << CS42L42_SW_GNDHS_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_GNDHS_HS3_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_HS4_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_HSB_FILT_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_HSB_FILT_HS3_SHIFT) | \
+					 (0 << CS42L42_SW_REF_HS4_SHIFT) | \
+					 (1 << CS42L42_SW_REF_HS3_SHIFT))
+
+#define CS42L42_HSDET_COMP_TYPE1	1
+#define CS42L42_HSDET_COMP_TYPE2	2
+#define CS42L42_HSDET_COMP_TYPE3	0
+#define CS42L42_HSDET_COMP_TYPE4	3
+
+#define CS42L42_HS_CLAMP_DISABLE	(CS42L42_PAGE_11 + 0x29)
+#define CS42L42_HS_CLAMP_DISABLE_SHIFT	0
+#define CS42L42_HS_CLAMP_DISABLE_MASK	(1 << CS42L42_HS_CLAMP_DISABLE_SHIFT)
+
+/* Page 0x12 Clocking Registers */
+#define CS42L42_MCLK_SRC_SEL		(CS42L42_PAGE_12 + 0x01)
+#define CS42L42_MCLKDIV_SHIFT		1
+#define CS42L42_MCLKDIV_MASK		(1 << CS42L42_MCLKDIV_SHIFT)
+#define CS42L42_MCLK_SRC_SEL_SHIFT	0
+#define CS42L42_MCLK_SRC_SEL_MASK	(1 << CS42L42_MCLK_SRC_SEL_SHIFT)
+
+#define CS42L42_SPDIF_CLK_CFG		(CS42L42_PAGE_12 + 0x02)
+#define CS42L42_FSYNC_PW_LOWER		(CS42L42_PAGE_12 + 0x03)
+
+#define CS42L42_FSYNC_PW_UPPER			(CS42L42_PAGE_12 + 0x04)
+#define CS42L42_FSYNC_PULSE_WIDTH_SHIFT		0
+#define CS42L42_FSYNC_PULSE_WIDTH_MASK		(0xff << \
+					CS42L42_FSYNC_PULSE_WIDTH_SHIFT)
+
+#define CS42L42_FSYNC_P_LOWER		(CS42L42_PAGE_12 + 0x05)
+
+#define CS42L42_FSYNC_P_UPPER		(CS42L42_PAGE_12 + 0x06)
+#define CS42L42_FSYNC_PERIOD_SHIFT	0
+#define CS42L42_FSYNC_PERIOD_MASK	(0xff << CS42L42_FSYNC_PERIOD_SHIFT)
+
+#define CS42L42_ASP_CLK_CFG		(CS42L42_PAGE_12 + 0x07)
+#define CS42L42_ASP_SCLK_EN_SHIFT	5
+#define CS42L42_ASP_SCLK_EN_MASK	(1 << CS42L42_ASP_SCLK_EN_SHIFT)
+#define CS42L42_ASP_MASTER_MODE		0x01
+#define CS42L42_ASP_SLAVE_MODE		0x00
+#define CS42L42_ASP_MODE_SHIFT		4
+#define CS42L42_ASP_MODE_MASK		(1 << CS42L42_ASP_MODE_SHIFT)
+#define CS42L42_ASP_SCPOL_SHIFT		2
+#define CS42L42_ASP_SCPOL_MASK		(3 << CS42L42_ASP_SCPOL_SHIFT)
+#define CS42L42_ASP_SCPOL_NOR		3
+#define CS42L42_ASP_LCPOL_SHIFT		0
+#define CS42L42_ASP_LCPOL_MASK		(3 << CS42L42_ASP_LCPOL_SHIFT)
+#define CS42L42_ASP_LCPOL_INV		3
+
+#define CS42L42_ASP_FRM_CFG		(CS42L42_PAGE_12 + 0x08)
+#define CS42L42_ASP_STP_SHIFT		4
+#define CS42L42_ASP_STP_MASK		(1 << CS42L42_ASP_STP_SHIFT)
+#define CS42L42_ASP_5050_SHIFT		3
+#define CS42L42_ASP_5050_MASK		(1 << CS42L42_ASP_5050_SHIFT)
+#define CS42L42_ASP_FSD_SHIFT		0
+#define CS42L42_ASP_FSD_MASK		(7 << CS42L42_ASP_FSD_SHIFT)
+#define CS42L42_ASP_FSD_0_5		1
+#define CS42L42_ASP_FSD_1_0		2
+#define CS42L42_ASP_FSD_1_5		3
+#define CS42L42_ASP_FSD_2_0		4
+
+#define CS42L42_FS_RATE_EN		(CS42L42_PAGE_12 + 0x09)
+#define CS42L42_FS_EN_SHIFT		0
+#define CS42L42_FS_EN_MASK		(0xf << CS42L42_FS_EN_SHIFT)
+#define CS42L42_FS_EN_IASRC_96K		0x1
+#define CS42L42_FS_EN_OASRC_96K		0x2
+
+#define CS42L42_IN_ASRC_CLK		(CS42L42_PAGE_12 + 0x0A)
+#define CS42L42_CLK_IASRC_SEL_SHIFT	0
+#define CS42L42_CLK_IASRC_SEL_MASK	(1 << CS42L42_CLK_IASRC_SEL_SHIFT)
+#define CS42L42_CLK_IASRC_SEL_6		0
+#define CS42L42_CLK_IASRC_SEL_12	1
+
+#define CS42L42_OUT_ASRC_CLK		(CS42L42_PAGE_12 + 0x0B)
+#define CS42L42_CLK_OASRC_SEL_SHIFT	0
+#define CS42L42_CLK_OASRC_SEL_MASK	(1 << CS42L42_CLK_OASRC_SEL_SHIFT)
+#define CS42L42_CLK_OASRC_SEL_12	1
+
+#define CS42L42_PLL_DIV_CFG1		(CS42L42_PAGE_12 + 0x0C)
+#define CS42L42_SCLK_PREDIV_SHIFT	0
+#define CS42L42_SCLK_PREDIV_MASK	(3 << CS42L42_SCLK_PREDIV_SHIFT)
+
+/* Page 0x13 Interrupt Registers */
+/* Interrupts */
+#define CS42L42_ADC_OVFL_STATUS		(CS42L42_PAGE_13 + 0x01)
+#define CS42L42_MIXER_STATUS		(CS42L42_PAGE_13 + 0x02)
+#define CS42L42_SRC_STATUS		(CS42L42_PAGE_13 + 0x03)
+#define CS42L42_ASP_RX_STATUS		(CS42L42_PAGE_13 + 0x04)
+#define CS42L42_ASP_TX_STATUS		(CS42L42_PAGE_13 + 0x05)
+#define CS42L42_CODEC_STATUS		(CS42L42_PAGE_13 + 0x08)
+#define CS42L42_DET_INT_STATUS1		(CS42L42_PAGE_13 + 0x09)
+#define CS42L42_DET_INT_STATUS2		(CS42L42_PAGE_13 + 0x0A)
+#define CS42L42_SRCPL_INT_STATUS	(CS42L42_PAGE_13 + 0x0B)
+#define CS42L42_VPMON_STATUS		(CS42L42_PAGE_13 + 0x0D)
+#define CS42L42_PLL_LOCK_STATUS		(CS42L42_PAGE_13 + 0x0E)
+#define CS42L42_TSRS_PLUG_STATUS	(CS42L42_PAGE_13 + 0x0F)
+/* Masks */
+#define CS42L42_ADC_OVFL_INT_MASK	(CS42L42_PAGE_13 + 0x16)
+#define CS42L42_ADC_OVFL_SHIFT		0
+#define CS42L42_ADC_OVFL_MASK		(1 << CS42L42_ADC_OVFL_SHIFT)
+#define CS42L42_ADC_OVFL_VAL_MASK	CS42L42_ADC_OVFL_MASK
+
+#define CS42L42_MIXER_INT_MASK		(CS42L42_PAGE_13 + 0x17)
+#define CS42L42_MIX_CHB_OVFL_SHIFT	0
+#define CS42L42_MIX_CHB_OVFL_MASK	(1 << CS42L42_MIX_CHB_OVFL_SHIFT)
+#define CS42L42_MIX_CHA_OVFL_SHIFT	1
+#define CS42L42_MIX_CHA_OVFL_MASK	(1 << CS42L42_MIX_CHA_OVFL_SHIFT)
+#define CS42L42_EQ_OVFL_SHIFT		2
+#define CS42L42_EQ_OVFL_MASK		(1 << CS42L42_EQ_OVFL_SHIFT)
+#define CS42L42_EQ_BIQUAD_OVFL_SHIFT	3
+#define CS42L42_EQ_BIQUAD_OVFL_MASK	(1 << CS42L42_EQ_BIQUAD_OVFL_SHIFT)
+#define CS42L42_MIXER_VAL_MASK		(CS42L42_MIX_CHB_OVFL_MASK | \
+					CS42L42_MIX_CHA_OVFL_MASK | \
+					CS42L42_EQ_OVFL_MASK | \
+					CS42L42_EQ_BIQUAD_OVFL_MASK)
+
+#define CS42L42_SRC_INT_MASK		(CS42L42_PAGE_13 + 0x18)
+#define CS42L42_SRC_ILK_SHIFT		0
+#define CS42L42_SRC_ILK_MASK		(1 << CS42L42_SRC_ILK_SHIFT)
+#define CS42L42_SRC_OLK_SHIFT		1
+#define CS42L42_SRC_OLK_MASK		(1 << CS42L42_SRC_OLK_SHIFT)
+#define CS42L42_SRC_IUNLK_SHIFT		2
+#define CS42L42_SRC_IUNLK_MASK		(1 << CS42L42_SRC_IUNLK_SHIFT)
+#define CS42L42_SRC_OUNLK_SHIFT		3
+#define CS42L42_SRC_OUNLK_MASK		(1 << CS42L42_SRC_OUNLK_SHIFT)
+#define CS42L42_SRC_VAL_MASK		(CS42L42_SRC_ILK_MASK | \
+					CS42L42_SRC_OLK_MASK | \
+					CS42L42_SRC_IUNLK_MASK | \
+					CS42L42_SRC_OUNLK_MASK)
+
+#define CS42L42_ASP_RX_INT_MASK		(CS42L42_PAGE_13 + 0x19)
+#define CS42L42_ASPRX_NOLRCK_SHIFT	0
+#define CS42L42_ASPRX_NOLRCK_MASK	(1 << CS42L42_ASPRX_NOLRCK_SHIFT)
+#define CS42L42_ASPRX_EARLY_SHIFT	1
+#define CS42L42_ASPRX_EARLY_MASK	(1 << CS42L42_ASPRX_EARLY_SHIFT)
+#define CS42L42_ASPRX_LATE_SHIFT	2
+#define CS42L42_ASPRX_LATE_MASK		(1 << CS42L42_ASPRX_LATE_SHIFT)
+#define CS42L42_ASPRX_ERROR_SHIFT	3
+#define CS42L42_ASPRX_ERROR_MASK	(1 << CS42L42_ASPRX_ERROR_SHIFT)
+#define CS42L42_ASPRX_OVLD_SHIFT	4
+#define CS42L42_ASPRX_OVLD_MASK		(1 << CS42L42_ASPRX_OVLD_SHIFT)
+#define CS42L42_ASP_RX_VAL_MASK		(CS42L42_ASPRX_NOLRCK_MASK | \
+					CS42L42_ASPRX_EARLY_MASK | \
+					CS42L42_ASPRX_LATE_MASK | \
+					CS42L42_ASPRX_ERROR_MASK | \
+					CS42L42_ASPRX_OVLD_MASK)
+
+#define CS42L42_ASP_TX_INT_MASK		(CS42L42_PAGE_13 + 0x1A)
+#define CS42L42_ASPTX_NOLRCK_SHIFT	0
+#define CS42L42_ASPTX_NOLRCK_MASK	(1 << CS42L42_ASPTX_NOLRCK_SHIFT)
+#define CS42L42_ASPTX_EARLY_SHIFT	1
+#define CS42L42_ASPTX_EARLY_MASK	(1 << CS42L42_ASPTX_EARLY_SHIFT)
+#define CS42L42_ASPTX_LATE_SHIFT	2
+#define CS42L42_ASPTX_LATE_MASK		(1 << CS42L42_ASPTX_LATE_SHIFT)
+#define CS42L42_ASPTX_SMERROR_SHIFT	3
+#define CS42L42_ASPTX_SMERROR_MASK	(1 << CS42L42_ASPTX_SMERROR_SHIFT)
+#define CS42L42_ASP_TX_VAL_MASK		(CS42L42_ASPTX_NOLRCK_MASK | \
+					CS42L42_ASPTX_EARLY_MASK | \
+					CS42L42_ASPTX_LATE_MASK | \
+					CS42L42_ASPTX_SMERROR_MASK)
+
+#define CS42L42_CODEC_INT_MASK		(CS42L42_PAGE_13 + 0x1B)
+#define CS42L42_PDN_DONE_SHIFT		0
+#define CS42L42_PDN_DONE_MASK		(1 << CS42L42_PDN_DONE_SHIFT)
+#define CS42L42_HSDET_AUTO_DONE_SHIFT	1
+#define CS42L42_HSDET_AUTO_DONE_MASK	(1 << CS42L42_HSDET_AUTO_DONE_SHIFT)
+#define CS42L42_CODEC_VAL_MASK		(CS42L42_PDN_DONE_MASK | \
+					CS42L42_HSDET_AUTO_DONE_MASK)
+
+#define CS42L42_SRCPL_INT_MASK		(CS42L42_PAGE_13 + 0x1C)
+#define CS42L42_SRCPL_ADC_LK_SHIFT	0
+#define CS42L42_SRCPL_ADC_LK_MASK	(1 << CS42L42_SRCPL_ADC_LK_SHIFT)
+#define CS42L42_SRCPL_DAC_LK_SHIFT	2
+#define CS42L42_SRCPL_DAC_LK_MASK	(1 << CS42L42_SRCPL_DAC_LK_SHIFT)
+#define CS42L42_SRCPL_ADC_UNLK_SHIFT	5
+#define CS42L42_SRCPL_ADC_UNLK_MASK	(1 << CS42L42_SRCPL_ADC_UNLK_SHIFT)
+#define CS42L42_SRCPL_DAC_UNLK_SHIFT	6
+#define CS42L42_SRCPL_DAC_UNLK_MASK	(1 << CS42L42_SRCPL_DAC_UNLK_SHIFT)
+#define CS42L42_SRCPL_VAL_MASK		(CS42L42_SRCPL_ADC_LK_MASK | \
+					CS42L42_SRCPL_DAC_LK_MASK | \
+					CS42L42_SRCPL_ADC_UNLK_MASK | \
+					CS42L42_SRCPL_DAC_UNLK_MASK)
+
+#define CS42L42_VPMON_INT_MASK		(CS42L42_PAGE_13 + 0x1E)
+#define CS42L42_VPMON_SHIFT		0
+#define CS42L42_VPMON_MASK		(1 << CS42L42_VPMON_SHIFT)
+#define CS42L42_VPMON_VAL_MASK		CS42L42_VPMON_MASK
+
+#define CS42L42_PLL_LOCK_INT_MASK	(CS42L42_PAGE_13 + 0x1F)
+#define CS42L42_PLL_LOCK_SHIFT		0
+#define CS42L42_PLL_LOCK_MASK		(1 << CS42L42_PLL_LOCK_SHIFT)
+#define CS42L42_PLL_LOCK_VAL_MASK	CS42L42_PLL_LOCK_MASK
+
+#define CS42L42_TSRS_PLUG_INT_MASK	(CS42L42_PAGE_13 + 0x20)
+#define CS42L42_RS_PLUG_SHIFT		0
+#define CS42L42_RS_PLUG_MASK		(1 << CS42L42_RS_PLUG_SHIFT)
+#define CS42L42_RS_UNPLUG_SHIFT		1
+#define CS42L42_RS_UNPLUG_MASK		(1 << CS42L42_RS_UNPLUG_SHIFT)
+#define CS42L42_TS_PLUG_SHIFT		2
+#define CS42L42_TS_PLUG_MASK		(1 << CS42L42_TS_PLUG_SHIFT)
+#define CS42L42_TS_UNPLUG_SHIFT		3
+#define CS42L42_TS_UNPLUG_MASK		(1 << CS42L42_TS_UNPLUG_SHIFT)
+#define CS42L42_TSRS_PLUG_VAL_MASK	(CS42L42_RS_PLUG_MASK | \
+					CS42L42_RS_UNPLUG_MASK | \
+					CS42L42_TS_PLUG_MASK | \
+					CS42L42_TS_UNPLUG_MASK)
+#define CS42L42_TS_PLUG			3
+#define CS42L42_TS_UNPLUG		0
+#define CS42L42_TS_TRANS		1
+
+/*
+ * NOTE: PLL_START must be 0 while both ADC_PDN=1 and HP_PDN=1.
+ * Otherwise it will prevent FILT+ from charging properly.
+ */
+#define CS42L42_PLL_CTL1		(CS42L42_PAGE_15 + 0x01)
+#define CS42L42_PLL_START_SHIFT		0
+#define CS42L42_PLL_START_MASK		(1 << CS42L42_PLL_START_SHIFT)
+
+#define CS42L42_PLL_DIV_FRAC0		(CS42L42_PAGE_15 + 0x02)
+#define CS42L42_PLL_DIV_FRAC_SHIFT	0
+#define CS42L42_PLL_DIV_FRAC_MASK	(0xff << CS42L42_PLL_DIV_FRAC_SHIFT)
+
+#define CS42L42_PLL_DIV_FRAC1		(CS42L42_PAGE_15 + 0x03)
+#define CS42L42_PLL_DIV_FRAC2		(CS42L42_PAGE_15 + 0x04)
+
+#define CS42L42_PLL_DIV_INT		(CS42L42_PAGE_15 + 0x05)
+#define CS42L42_PLL_DIV_INT_SHIFT	0
+#define CS42L42_PLL_DIV_INT_MASK	(0xff << CS42L42_PLL_DIV_INT_SHIFT)
+
+#define CS42L42_PLL_CTL3		(CS42L42_PAGE_15 + 0x08)
+#define CS42L42_PLL_DIVOUT_SHIFT	0
+#define CS42L42_PLL_DIVOUT_MASK		(0xff << CS42L42_PLL_DIVOUT_SHIFT)
+
+#define CS42L42_PLL_CAL_RATIO		(CS42L42_PAGE_15 + 0x0A)
+#define CS42L42_PLL_CAL_RATIO_SHIFT	0
+#define CS42L42_PLL_CAL_RATIO_MASK	(0xff << CS42L42_PLL_CAL_RATIO_SHIFT)
+
+#define CS42L42_PLL_CTL4		(CS42L42_PAGE_15 + 0x1B)
+#define CS42L42_PLL_MODE_SHIFT		0
+#define CS42L42_PLL_MODE_MASK		(3 << CS42L42_PLL_MODE_SHIFT)
+
+/* Page 0x19 HP Load Detect Registers */
+#define CS42L42_LOAD_DET_RCSTAT		(CS42L42_PAGE_19 + 0x25)
+#define CS42L42_RLA_STAT_SHIFT		0
+#define CS42L42_RLA_STAT_MASK		(3 << CS42L42_RLA_STAT_SHIFT)
+#define CS42L42_RLA_STAT_15_OHM		0
+
+#define CS42L42_LOAD_DET_DONE		(CS42L42_PAGE_19 + 0x26)
+#define CS42L42_HPLOAD_DET_DONE_SHIFT	0
+#define CS42L42_HPLOAD_DET_DONE_MASK	(1 << CS42L42_HPLOAD_DET_DONE_SHIFT)
+
+#define CS42L42_LOAD_DET_EN		(CS42L42_PAGE_19 + 0x27)
+#define CS42L42_HP_LD_EN_SHIFT		0
+#define CS42L42_HP_LD_EN_MASK		(1 << CS42L42_HP_LD_EN_SHIFT)
+
+/* Page 0x1B Headset Interface Registers */
+#define CS42L42_HSBIAS_SC_AUTOCTL		(CS42L42_PAGE_1B + 0x70)
+#define CS42L42_HSBIAS_SENSE_TRIP_SHIFT		0
+#define CS42L42_HSBIAS_SENSE_TRIP_MASK		(7 << CS42L42_HSBIAS_SENSE_TRIP_SHIFT)
+#define CS42L42_TIP_SENSE_EN_SHIFT		5
+#define CS42L42_TIP_SENSE_EN_MASK		(1 << CS42L42_TIP_SENSE_EN_SHIFT)
+#define CS42L42_AUTO_HSBIAS_HIZ_SHIFT		6
+#define CS42L42_AUTO_HSBIAS_HIZ_MASK		(1 << CS42L42_AUTO_HSBIAS_HIZ_SHIFT)
+#define CS42L42_HSBIAS_SENSE_EN_SHIFT		7
+#define CS42L42_HSBIAS_SENSE_EN_MASK		(1 << CS42L42_HSBIAS_SENSE_EN_SHIFT)
+
+#define CS42L42_WAKE_CTL		(CS42L42_PAGE_1B + 0x71)
+#define CS42L42_WAKEB_CLEAR_SHIFT	0
+#define CS42L42_WAKEB_CLEAR_MASK	(1 << CS42L42_WAKEB_CLEAR_SHIFT)
+#define CS42L42_WAKEB_MODE_SHIFT	5
+#define CS42L42_WAKEB_MODE_MASK		(1 << CS42L42_WAKEB_MODE_SHIFT)
+#define CS42L42_M_HP_WAKE_SHIFT		6
+#define CS42L42_M_HP_WAKE_MASK		(1 << CS42L42_M_HP_WAKE_SHIFT)
+#define CS42L42_M_MIC_WAKE_SHIFT	7
+#define CS42L42_M_MIC_WAKE_MASK		(1 << CS42L42_M_MIC_WAKE_SHIFT)
+
+#define CS42L42_ADC_DISABLE_MUTE		(CS42L42_PAGE_1B + 0x72)
+#define CS42L42_ADC_DISABLE_S0_MUTE_SHIFT	7
+#define CS42L42_ADC_DISABLE_S0_MUTE_MASK	(1 << CS42L42_ADC_DISABLE_S0_MUTE_SHIFT)
+
+#define CS42L42_TIPSENSE_CTL			(CS42L42_PAGE_1B + 0x73)
+#define CS42L42_TIP_SENSE_DEBOUNCE_SHIFT	0
+#define CS42L42_TIP_SENSE_DEBOUNCE_MASK		(3 << CS42L42_TIP_SENSE_DEBOUNCE_SHIFT)
+#define CS42L42_TIP_SENSE_INV_SHIFT		5
+#define CS42L42_TIP_SENSE_INV_MASK		(1 << CS42L42_TIP_SENSE_INV_SHIFT)
+#define CS42L42_TIP_SENSE_CTRL_SHIFT		6
+#define CS42L42_TIP_SENSE_CTRL_MASK		(3 << CS42L42_TIP_SENSE_CTRL_SHIFT)
+
+/*
+ * NOTE: DETECT_MODE must be 0 while both ADC_PDN=1 and HP_PDN=1.
+ * Otherwise it will prevent FILT+ from charging properly.
+ */
+#define CS42L42_MISC_DET_CTL		(CS42L42_PAGE_1B + 0x74)
+#define CS42L42_PDN_MIC_LVL_DET_SHIFT	0
+#define CS42L42_PDN_MIC_LVL_DET_MASK	(1 << CS42L42_PDN_MIC_LVL_DET_SHIFT)
+#define CS42L42_HSBIAS_CTL_SHIFT	1
+#define CS42L42_HSBIAS_CTL_MASK		(3 << CS42L42_HSBIAS_CTL_SHIFT)
+#define CS42L42_DETECT_MODE_SHIFT	3
+#define CS42L42_DETECT_MODE_MASK	(3 << CS42L42_DETECT_MODE_SHIFT)
+
+#define CS42L42_MIC_DET_CTL1		(CS42L42_PAGE_1B + 0x75)
+#define CS42L42_HS_DET_LEVEL_SHIFT	0
+#define CS42L42_HS_DET_LEVEL_MASK	(0x3F << CS42L42_HS_DET_LEVEL_SHIFT)
+#define CS42L42_EVENT_STAT_SEL_SHIFT	6
+#define CS42L42_EVENT_STAT_SEL_MASK	(1 << CS42L42_EVENT_STAT_SEL_SHIFT)
+#define CS42L42_LATCH_TO_VP_SHIFT	7
+#define CS42L42_LATCH_TO_VP_MASK	(1 << CS42L42_LATCH_TO_VP_SHIFT)
+
+#define CS42L42_MIC_DET_CTL2		(CS42L42_PAGE_1B + 0x76)
+#define CS42L42_DEBOUNCE_TIME_SHIFT	5
+#define CS42L42_DEBOUNCE_TIME_MASK	(0x07 << CS42L42_DEBOUNCE_TIME_SHIFT)
+
+#define CS42L42_DET_STATUS1		(CS42L42_PAGE_1B + 0x77)
+#define CS42L42_HSBIAS_HIZ_MODE_SHIFT	6
+#define CS42L42_HSBIAS_HIZ_MODE_MASK	(1 << CS42L42_HSBIAS_HIZ_MODE_SHIFT)
+#define CS42L42_TIP_SENSE_SHIFT		7
+#define CS42L42_TIP_SENSE_MASK		(1 << CS42L42_TIP_SENSE_SHIFT)
+
+#define CS42L42_DET_STATUS2		(CS42L42_PAGE_1B + 0x78)
+#define CS42L42_SHORT_TRUE_SHIFT	0
+#define CS42L42_SHORT_TRUE_MASK		(1 << CS42L42_SHORT_TRUE_SHIFT)
+#define CS42L42_HS_TRUE_SHIFT	1
+#define CS42L42_HS_TRUE_MASK		(1 << CS42L42_HS_TRUE_SHIFT)
+
+#define CS42L42_DET_INT1_MASK		(CS42L42_PAGE_1B + 0x79)
+#define CS42L42_TIP_SENSE_UNPLUG_SHIFT	5
+#define CS42L42_TIP_SENSE_UNPLUG_MASK	(1 << CS42L42_TIP_SENSE_UNPLUG_SHIFT)
+#define CS42L42_TIP_SENSE_PLUG_SHIFT	6
+#define CS42L42_TIP_SENSE_PLUG_MASK	(1 << CS42L42_TIP_SENSE_PLUG_SHIFT)
+#define CS42L42_HSBIAS_SENSE_SHIFT	7
+#define CS42L42_HSBIAS_SENSE_MASK	(1 << CS42L42_HSBIAS_SENSE_SHIFT)
+#define CS42L42_DET_INT_VAL1_MASK	(CS42L42_TIP_SENSE_UNPLUG_MASK | \
+					CS42L42_TIP_SENSE_PLUG_MASK | \
+					CS42L42_HSBIAS_SENSE_MASK)
+
+#define CS42L42_DET_INT2_MASK		(CS42L42_PAGE_1B + 0x7A)
+#define CS42L42_M_SHORT_DET_SHIFT	0
+#define CS42L42_M_SHORT_DET_MASK	(1 << CS42L42_M_SHORT_DET_SHIFT)
+#define CS42L42_M_SHORT_RLS_SHIFT	1
+#define CS42L42_M_SHORT_RLS_MASK	(1 << CS42L42_M_SHORT_RLS_SHIFT)
+#define CS42L42_M_HSBIAS_HIZ_SHIFT	2
+#define CS42L42_M_HSBIAS_HIZ_MASK	(1 << CS42L42_M_HSBIAS_HIZ_SHIFT)
+#define CS42L42_M_DETECT_FT_SHIFT	6
+#define CS42L42_M_DETECT_FT_MASK	(1 << CS42L42_M_DETECT_FT_SHIFT)
+#define CS42L42_M_DETECT_TF_SHIFT	7
+#define CS42L42_M_DETECT_TF_MASK	(1 << CS42L42_M_DETECT_TF_SHIFT)
+#define CS42L42_DET_INT_VAL2_MASK	(CS42L42_M_SHORT_DET_MASK | \
+					CS42L42_M_SHORT_RLS_MASK | \
+					CS42L42_M_HSBIAS_HIZ_MASK | \
+					CS42L42_M_DETECT_FT_MASK | \
+					CS42L42_M_DETECT_TF_MASK)
+
+/* Page 0x1C Headset Bias Registers */
+#define CS42L42_HS_BIAS_CTL		(CS42L42_PAGE_1C + 0x03)
+#define CS42L42_HSBIAS_RAMP_SHIFT	0
+#define CS42L42_HSBIAS_RAMP_MASK	(3 << CS42L42_HSBIAS_RAMP_SHIFT)
+#define CS42L42_HSBIAS_PD_SHIFT		4
+#define CS42L42_HSBIAS_PD_MASK		(1 << CS42L42_HSBIAS_PD_SHIFT)
+#define CS42L42_HSBIAS_CAPLESS_SHIFT	7
+#define CS42L42_HSBIAS_CAPLESS_MASK	(1 << CS42L42_HSBIAS_CAPLESS_SHIFT)
+
+/* Page 0x1D ADC Registers */
+#define CS42L42_ADC_CTL			(CS42L42_PAGE_1D + 0x01)
+#define CS42L42_ADC_NOTCH_DIS_SHIFT		5
+#define CS42L42_ADC_FORCE_WEAK_VCM_SHIFT	4
+#define CS42L42_ADC_INV_SHIFT			2
+#define CS42L42_ADC_DIG_BOOST_SHIFT		0
+
+#define CS42L42_ADC_VOLUME		(CS42L42_PAGE_1D + 0x03)
+#define CS42L42_ADC_VOL_SHIFT		0
+
+#define CS42L42_ADC_WNF_HPF_CTL		(CS42L42_PAGE_1D + 0x04)
+#define CS42L42_ADC_WNF_CF_SHIFT	4
+#define CS42L42_ADC_WNF_EN_SHIFT	3
+#define CS42L42_ADC_HPF_CF_SHIFT	1
+#define CS42L42_ADC_HPF_EN_SHIFT	0
+
+/* Page 0x1F DAC Registers */
+#define CS42L42_DAC_CTL1		(CS42L42_PAGE_1F + 0x01)
+#define CS42L42_DACB_INV_SHIFT		1
+#define CS42L42_DACA_INV_SHIFT		0
+
+#define CS42L42_DAC_CTL2		(CS42L42_PAGE_1F + 0x06)
+#define CS42L42_HPOUT_PULLDOWN_SHIFT	4
+#define CS42L42_HPOUT_PULLDOWN_MASK	(15 << CS42L42_HPOUT_PULLDOWN_SHIFT)
+#define CS42L42_HPOUT_LOAD_SHIFT	3
+#define CS42L42_HPOUT_LOAD_MASK		(1 << CS42L42_HPOUT_LOAD_SHIFT)
+#define CS42L42_HPOUT_CLAMP_SHIFT	2
+#define CS42L42_HPOUT_CLAMP_MASK	(1 << CS42L42_HPOUT_CLAMP_SHIFT)
+#define CS42L42_DAC_HPF_EN_SHIFT	1
+#define CS42L42_DAC_HPF_EN_MASK		(1 << CS42L42_DAC_HPF_EN_SHIFT)
+#define CS42L42_DAC_MON_EN_SHIFT	0
+#define CS42L42_DAC_MON_EN_MASK		(1 << CS42L42_DAC_MON_EN_SHIFT)
+
+/* Page 0x20 HP CTL Registers */
+#define CS42L42_HP_CTL			(CS42L42_PAGE_20 + 0x01)
+#define CS42L42_HP_ANA_BMUTE_SHIFT	3
+#define CS42L42_HP_ANA_BMUTE_MASK	(1 << CS42L42_HP_ANA_BMUTE_SHIFT)
+#define CS42L42_HP_ANA_AMUTE_SHIFT	2
+#define CS42L42_HP_ANA_AMUTE_MASK	(1 << CS42L42_HP_ANA_AMUTE_SHIFT)
+#define CS42L42_HP_FULL_SCALE_VOL_SHIFT	1
+#define CS42L42_HP_FULL_SCALE_VOL_MASK	(1 << CS42L42_HP_FULL_SCALE_VOL_SHIFT)
+
+/* Page 0x21 Class H Registers */
+#define CS42L42_CLASSH_CTL		(CS42L42_PAGE_21 + 0x01)
+
+/* Page 0x23 Mixer Volume Registers */
+#define CS42L42_MIXER_CHA_VOL		(CS42L42_PAGE_23 + 0x01)
+#define CS42L42_MIXER_ADC_VOL		(CS42L42_PAGE_23 + 0x02)
+
+#define CS42L42_MIXER_CHB_VOL		(CS42L42_PAGE_23 + 0x03)
+#define CS42L42_MIXER_CH_VOL_SHIFT	0
+#define CS42L42_MIXER_CH_VOL_MASK	(0x3f << CS42L42_MIXER_CH_VOL_SHIFT)
+
+/* Page 0x24 EQ Registers */
+#define CS42L42_EQ_COEF_IN0		(CS42L42_PAGE_24 + 0x01)
+#define CS42L42_EQ_COEF_IN1		(CS42L42_PAGE_24 + 0x02)
+#define CS42L42_EQ_COEF_IN2		(CS42L42_PAGE_24 + 0x03)
+#define CS42L42_EQ_COEF_IN3		(CS42L42_PAGE_24 + 0x04)
+#define CS42L42_EQ_COEF_RW		(CS42L42_PAGE_24 + 0x06)
+#define CS42L42_EQ_COEF_OUT0		(CS42L42_PAGE_24 + 0x07)
+#define CS42L42_EQ_COEF_OUT1		(CS42L42_PAGE_24 + 0x08)
+#define CS42L42_EQ_COEF_OUT2		(CS42L42_PAGE_24 + 0x09)
+#define CS42L42_EQ_COEF_OUT3		(CS42L42_PAGE_24 + 0x0A)
+#define CS42L42_EQ_INIT_STAT		(CS42L42_PAGE_24 + 0x0B)
+#define CS42L42_EQ_START_FILT		(CS42L42_PAGE_24 + 0x0C)
+#define CS42L42_EQ_MUTE_CTL		(CS42L42_PAGE_24 + 0x0E)
+
+/* Page 0x25 Audio Port Registers */
+#define CS42L42_SP_RX_CH_SEL		(CS42L42_PAGE_25 + 0x01)
+#define CS42L42_SP_RX_CHB_SEL_SHIFT	2
+#define CS42L42_SP_RX_CHB_SEL_MASK	(3 << CS42L42_SP_RX_CHB_SEL_SHIFT)
+
+#define CS42L42_SP_RX_ISOC_CTL		(CS42L42_PAGE_25 + 0x02)
+#define CS42L42_SP_RX_RSYNC_SHIFT	6
+#define CS42L42_SP_RX_RSYNC_MASK	(1 << CS42L42_SP_RX_RSYNC_SHIFT)
+#define CS42L42_SP_RX_NSB_POS_SHIFT	3
+#define CS42L42_SP_RX_NSB_POS_MASK	(7 << CS42L42_SP_RX_NSB_POS_SHIFT)
+#define CS42L42_SP_RX_NFS_NSBB_SHIFT	2
+#define CS42L42_SP_RX_NFS_NSBB_MASK	(1 << CS42L42_SP_RX_NFS_NSBB_SHIFT)
+#define CS42L42_SP_RX_ISOC_MODE_SHIFT	0
+#define CS42L42_SP_RX_ISOC_MODE_MASK	(3 << CS42L42_SP_RX_ISOC_MODE_SHIFT)
+
+#define CS42L42_SP_RX_FS		(CS42L42_PAGE_25 + 0x03)
+#define CS42l42_SPDIF_CH_SEL		(CS42L42_PAGE_25 + 0x04)
+#define CS42L42_SP_TX_ISOC_CTL		(CS42L42_PAGE_25 + 0x05)
+#define CS42L42_SP_TX_FS		(CS42L42_PAGE_25 + 0x06)
+#define CS42L42_SPDIF_SW_CTL1		(CS42L42_PAGE_25 + 0x07)
+
+/* Page 0x26 SRC Registers */
+#define CS42L42_SRC_SDIN_FS		(CS42L42_PAGE_26 + 0x01)
+#define CS42L42_SRC_SDIN_FS_SHIFT	0
+#define CS42L42_SRC_SDIN_FS_MASK	(0x1f << CS42L42_SRC_SDIN_FS_SHIFT)
+
+#define CS42L42_SRC_SDOUT_FS		(CS42L42_PAGE_26 + 0x09)
+
+/* Page 0x28 S/PDIF Registers */
+#define CS42L42_SPDIF_CTL1		(CS42L42_PAGE_28 + 0x01)
+#define CS42L42_SPDIF_CTL2		(CS42L42_PAGE_28 + 0x02)
+#define CS42L42_SPDIF_CTL3		(CS42L42_PAGE_28 + 0x03)
+#define CS42L42_SPDIF_CTL4		(CS42L42_PAGE_28 + 0x04)
+
+/* Page 0x29 Serial Port TX Registers */
+#define CS42L42_ASP_TX_SZ_EN		(CS42L42_PAGE_29 + 0x01)
+#define CS42L42_ASP_TX_EN_SHIFT		0
+#define CS42L42_ASP_TX_CH_EN		(CS42L42_PAGE_29 + 0x02)
+#define CS42L42_ASP_TX0_CH2_SHIFT	1
+#define CS42L42_ASP_TX0_CH1_SHIFT	0
+
+#define CS42L42_ASP_TX_CH_AP_RES	(CS42L42_PAGE_29 + 0x03)
+#define CS42L42_ASP_TX_CH1_AP_SHIFT	7
+#define CS42L42_ASP_TX_CH1_AP_MASK	(1 << CS42L42_ASP_TX_CH1_AP_SHIFT)
+#define CS42L42_ASP_TX_CH2_AP_SHIFT	6
+#define CS42L42_ASP_TX_CH2_AP_MASK	(1 << CS42L42_ASP_TX_CH2_AP_SHIFT)
+#define CS42L42_ASP_TX_CH2_RES_SHIFT	2
+#define CS42L42_ASP_TX_CH2_RES_MASK	(3 << CS42L42_ASP_TX_CH2_RES_SHIFT)
+#define CS42L42_ASP_TX_CH1_RES_SHIFT	0
+#define CS42L42_ASP_TX_CH1_RES_MASK	(3 << CS42L42_ASP_TX_CH1_RES_SHIFT)
+#define CS42L42_ASP_TX_CH1_BIT_MSB	(CS42L42_PAGE_29 + 0x04)
+#define CS42L42_ASP_TX_CH1_BIT_LSB	(CS42L42_PAGE_29 + 0x05)
+#define CS42L42_ASP_TX_HIZ_DLY_CFG	(CS42L42_PAGE_29 + 0x06)
+#define CS42L42_ASP_TX_CH2_BIT_MSB	(CS42L42_PAGE_29 + 0x0A)
+#define CS42L42_ASP_TX_CH2_BIT_LSB	(CS42L42_PAGE_29 + 0x0B)
+
+/* Page 0x2A Serial Port RX Registers */
+#define CS42L42_ASP_RX_DAI0_EN		(CS42L42_PAGE_2A + 0x01)
+#define CS42L42_ASP_RX0_CH_EN_SHIFT	2
+#define CS42L42_ASP_RX0_CH_EN_MASK	(0xf << CS42L42_ASP_RX0_CH_EN_SHIFT)
+#define CS42L42_ASP_RX0_CH1_SHIFT	2
+#define CS42L42_ASP_RX0_CH2_SHIFT	3
+#define CS42L42_ASP_RX0_CH3_SHIFT	4
+#define CS42L42_ASP_RX0_CH4_SHIFT	5
+
+#define CS42L42_ASP_RX_DAI0_CH1_AP_RES	(CS42L42_PAGE_2A + 0x02)
+#define CS42L42_ASP_RX_DAI0_CH1_BIT_MSB	(CS42L42_PAGE_2A + 0x03)
+#define CS42L42_ASP_RX_DAI0_CH1_BIT_LSB	(CS42L42_PAGE_2A + 0x04)
+#define CS42L42_ASP_RX_DAI0_CH2_AP_RES	(CS42L42_PAGE_2A + 0x05)
+#define CS42L42_ASP_RX_DAI0_CH2_BIT_MSB	(CS42L42_PAGE_2A + 0x06)
+#define CS42L42_ASP_RX_DAI0_CH2_BIT_LSB	(CS42L42_PAGE_2A + 0x07)
+#define CS42L42_ASP_RX_DAI0_CH3_AP_RES	(CS42L42_PAGE_2A + 0x08)
+#define CS42L42_ASP_RX_DAI0_CH3_BIT_MSB	(CS42L42_PAGE_2A + 0x09)
+#define CS42L42_ASP_RX_DAI0_CH3_BIT_LSB	(CS42L42_PAGE_2A + 0x0A)
+#define CS42L42_ASP_RX_DAI0_CH4_AP_RES	(CS42L42_PAGE_2A + 0x0B)
+#define CS42L42_ASP_RX_DAI0_CH4_BIT_MSB	(CS42L42_PAGE_2A + 0x0C)
+#define CS42L42_ASP_RX_DAI0_CH4_BIT_LSB	(CS42L42_PAGE_2A + 0x0D)
+#define CS42L42_ASP_RX_DAI1_CH1_AP_RES	(CS42L42_PAGE_2A + 0x0E)
+#define CS42L42_ASP_RX_DAI1_CH1_BIT_MSB	(CS42L42_PAGE_2A + 0x0F)
+#define CS42L42_ASP_RX_DAI1_CH1_BIT_LSB	(CS42L42_PAGE_2A + 0x10)
+#define CS42L42_ASP_RX_DAI1_CH2_AP_RES	(CS42L42_PAGE_2A + 0x11)
+#define CS42L42_ASP_RX_DAI1_CH2_BIT_MSB	(CS42L42_PAGE_2A + 0x12)
+#define CS42L42_ASP_RX_DAI1_CH2_BIT_LSB	(CS42L42_PAGE_2A + 0x13)
+
+#define CS42L42_ASP_RX_CH_AP_SHIFT	6
+#define CS42L42_ASP_RX_CH_AP_MASK	(1 << CS42L42_ASP_RX_CH_AP_SHIFT)
+#define CS42L42_ASP_RX_CH_AP_LOW	0
+#define CS42L42_ASP_RX_CH_AP_HI		1
+#define CS42L42_ASP_RX_CH_RES_SHIFT	0
+#define CS42L42_ASP_RX_CH_RES_MASK	(3 << CS42L42_ASP_RX_CH_RES_SHIFT)
+#define CS42L42_ASP_RX_CH_RES_32	3
+#define CS42L42_ASP_RX_CH_RES_16	1
+#define CS42L42_ASP_RX_CH_BIT_ST_SHIFT	0
+#define CS42L42_ASP_RX_CH_BIT_ST_MASK	(0xff << CS42L42_ASP_RX_CH_BIT_ST_SHIFT)
+
+/* Page 0x30 ID Registers */
+#define CS42L42_SUB_REVID		(CS42L42_PAGE_30 + 0x14)
+#define CS42L42_MAX_REGISTER		(CS42L42_PAGE_30 + 0x14)
+
+/* Defines for fracturing values spread across multiple registers */
+#define CS42L42_FRAC0_VAL(val)	((val) & 0x0000ff)
+#define CS42L42_FRAC1_VAL(val)	(((val) & 0x00ff00) >> 8)
+#define CS42L42_FRAC2_VAL(val)	(((val) & 0xff0000) >> 16)
+
+#define CS42L42_NUM_SUPPLIES	5
+#define CS42L42_BOOT_TIME_US	3000
+#define CS42L42_PLL_DIVOUT_TIME_US	800
+#define CS42L42_CLOCK_SWITCH_DELAY_US 150
+#define CS42L42_PLL_LOCK_POLL_US	250
+#define CS42L42_PLL_LOCK_TIMEOUT_US	1250
+#define CS42L42_HP_ADC_EN_TIME_US	20000
+#define CS42L42_PDN_DONE_POLL_US	1000
+#define CS42L42_PDN_DONE_TIMEOUT_US	200000
+#define CS42L42_PDN_DONE_TIME_MS	100
+#define CS42L42_FILT_DISCHARGE_TIME_MS	46
+
+#endif /* __CS42L42_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/dmaengine_pcm.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/dmaengine_pcm.h
@@ -34,6 +34,7 @@
 int snd_dmaengine_pcm_open(struct snd_pcm_substream *substream,
 	struct dma_chan *chan);
 int snd_dmaengine_pcm_close(struct snd_pcm_substream *substream);
+int snd_dmaengine_pcm_sync_stop(struct snd_pcm_substream *substream);
 
 int snd_dmaengine_pcm_open_request_chan(struct snd_pcm_substream *substream,
 	dma_filter_fn filter_fn, void *filter_data);
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/hda_codec.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/hda_codec.h
@@ -8,7 +8,7 @@
 #ifndef __SOUND_HDA_CODEC_H
 #define __SOUND_HDA_CODEC_H
 
-#include <linux/kref.h>
+#include <linux/refcount.h>
 #include <linux/mod_devicetable.h>
 #include <sound/info.h>
 #include <sound/control.h>
@@ -166,8 +166,8 @@
 	bool own_chmap;		/* codec driver provides own channel maps */
 	/* private: */
 	struct hda_codec *codec;
-	struct kref kref;
 	struct list_head list;
+	unsigned int disconnected:1;
 };
 
 /* codec information */
@@ -187,6 +187,8 @@
 
 	/* PCM to create, set by patch_ops.build_pcms callback */
 	struct list_head pcm_list_head;
+	refcount_t pcm_ref;
+	wait_queue_head_t remove_sleep;
 
 	/* codec specific info */
 	void *spec;
@@ -420,7 +422,7 @@
 
 static inline void snd_hda_codec_pcm_get(struct hda_pcm *pcm)
 {
-	kref_get(&pcm->kref);
+	refcount_inc(&pcm->codec->pcm_ref);
 }
 void snd_hda_codec_pcm_put(struct hda_pcm *pcm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/hdaudio.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/hdaudio.h
@@ -558,6 +558,8 @@
 void snd_hdac_stream_start(struct hdac_stream *azx_dev, bool fresh_start);
 void snd_hdac_stream_clear(struct hdac_stream *azx_dev);
 void snd_hdac_stream_stop(struct hdac_stream *azx_dev);
+void snd_hdac_stop_streams(struct hdac_bus *bus);
+void snd_hdac_stop_streams_and_chip(struct hdac_bus *bus);
 void snd_hdac_stream_reset(struct hdac_stream *azx_dev);
 void snd_hdac_stream_sync_trigger(struct hdac_stream *azx_dev, bool set,
 				  unsigned int streams, unsigned int reg);
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/hdaudio_ext.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/hdaudio_ext.h
@@ -88,9 +88,10 @@
 					   struct snd_pcm_substream *substream,
 					   int type);
 void snd_hdac_ext_stream_release(struct hdac_ext_stream *azx_dev, int type);
+void snd_hdac_ext_stream_decouple_locked(struct hdac_bus *bus,
+				  struct hdac_ext_stream *azx_dev, bool decouple);
 void snd_hdac_ext_stream_decouple(struct hdac_bus *bus,
 				struct hdac_ext_stream *azx_dev, bool decouple);
-void snd_hdac_ext_stop_streams(struct hdac_bus *bus);
 
 int snd_hdac_ext_stream_set_spib(struct hdac_bus *bus,
 				 struct hdac_ext_stream *stream, u32 value);
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/jack.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/jack.h
@@ -62,6 +62,7 @@
 	const char *id;
 #ifdef CONFIG_SND_JACK_INPUT_DEV
 	struct input_dev *input_dev;
+	struct mutex input_dev_lock;
 	int registered;
 	int type;
 	char name[100];
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/pcm.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/pcm.h
@@ -106,24 +106,24 @@
 #define SNDRV_PCM_POS_XRUN		((snd_pcm_uframes_t)-1)
 
 /* If you change this don't forget to change rates[] table in pcm_native.c */
-#define SNDRV_PCM_RATE_5512		(1<<0)		/* 5512Hz */
-#define SNDRV_PCM_RATE_8000		(1<<1)		/* 8000Hz */
-#define SNDRV_PCM_RATE_11025		(1<<2)		/* 11025Hz */
-#define SNDRV_PCM_RATE_16000		(1<<3)		/* 16000Hz */
-#define SNDRV_PCM_RATE_22050		(1<<4)		/* 22050Hz */
-#define SNDRV_PCM_RATE_32000		(1<<5)		/* 32000Hz */
-#define SNDRV_PCM_RATE_44100		(1<<6)		/* 44100Hz */
-#define SNDRV_PCM_RATE_48000		(1<<7)		/* 48000Hz */
-#define SNDRV_PCM_RATE_64000		(1<<8)		/* 64000Hz */
-#define SNDRV_PCM_RATE_88200		(1<<9)		/* 88200Hz */
-#define SNDRV_PCM_RATE_96000		(1<<10)		/* 96000Hz */
-#define SNDRV_PCM_RATE_176400		(1<<11)		/* 176400Hz */
-#define SNDRV_PCM_RATE_192000		(1<<12)		/* 192000Hz */
-#define SNDRV_PCM_RATE_352800		(1<<13)		/* 352800Hz */
-#define SNDRV_PCM_RATE_384000		(1<<14)		/* 384000Hz */
+#define SNDRV_PCM_RATE_5512		(1U<<0)		/* 5512Hz */
+#define SNDRV_PCM_RATE_8000		(1U<<1)		/* 8000Hz */
+#define SNDRV_PCM_RATE_11025		(1U<<2)		/* 11025Hz */
+#define SNDRV_PCM_RATE_16000		(1U<<3)		/* 16000Hz */
+#define SNDRV_PCM_RATE_22050		(1U<<4)		/* 22050Hz */
+#define SNDRV_PCM_RATE_32000		(1U<<5)		/* 32000Hz */
+#define SNDRV_PCM_RATE_44100		(1U<<6)		/* 44100Hz */
+#define SNDRV_PCM_RATE_48000		(1U<<7)		/* 48000Hz */
+#define SNDRV_PCM_RATE_64000		(1U<<8)		/* 64000Hz */
+#define SNDRV_PCM_RATE_88200		(1U<<9)		/* 88200Hz */
+#define SNDRV_PCM_RATE_96000		(1U<<10)	/* 96000Hz */
+#define SNDRV_PCM_RATE_176400		(1U<<11)	/* 176400Hz */
+#define SNDRV_PCM_RATE_192000		(1U<<12)	/* 192000Hz */
+#define SNDRV_PCM_RATE_352800		(1U<<13)	/* 352800Hz */
+#define SNDRV_PCM_RATE_384000		(1U<<14)	/* 384000Hz */
 
-#define SNDRV_PCM_RATE_CONTINUOUS	(1<<30)		/* continuous range */
-#define SNDRV_PCM_RATE_KNOT		(1<<31)		/* supports more non-continuos rates */
+#define SNDRV_PCM_RATE_CONTINUOUS	(1U<<30)	/* continuous range */
+#define SNDRV_PCM_RATE_KNOT		(1U<<31)	/* supports more non-continuos rates */
 
 #define SNDRV_PCM_RATE_8000_44100	(SNDRV_PCM_RATE_8000|SNDRV_PCM_RATE_11025|\
 					 SNDRV_PCM_RATE_16000|SNDRV_PCM_RATE_22050|\
@@ -343,6 +343,8 @@
 
 struct snd_pcm_runtime {
 	/* -- Status -- */
+	snd_pcm_state_t state;		/* stream state */
+	snd_pcm_state_t suspended_state; /* suspended stream state */
 	struct snd_pcm_substream *trigger_master;
 	struct timespec64 trigger_tstamp;	/* trigger timestamp */
 	bool trigger_tstamp_latched;     /* trigger timestamp latched in low-level driver/hardware */
@@ -398,6 +400,8 @@
 	wait_queue_head_t tsleep;	/* transfer sleep */
 	struct fasync_struct *fasync;
 	bool stop_operating;		/* sync_stop will be called */
+	struct mutex buffer_mutex;	/* protect for buffer changes */
+	atomic_t buffer_accessing;	/* >0: in r/w operation, <0: blocked */
 
 	/* -- private section -- */
 	void *private_data;
@@ -614,6 +618,7 @@
 void snd_pcm_stream_lock_irq(struct snd_pcm_substream *substream);
 void snd_pcm_stream_unlock_irq(struct snd_pcm_substream *substream);
 unsigned long _snd_pcm_stream_lock_irqsave(struct snd_pcm_substream *substream);
+unsigned long _snd_pcm_stream_lock_irqsave_nested(struct snd_pcm_substream *substream);
 
 /**
  * snd_pcm_stream_lock_irqsave - Lock the PCM stream
@@ -633,6 +638,20 @@
 				      unsigned long flags);
 
 /**
+ * snd_pcm_stream_lock_irqsave_nested - Single-nested PCM stream locking
+ * @substream: PCM substream
+ * @flags: irq flags
+ *
+ * This locks the PCM stream like snd_pcm_stream_lock_irqsave() but with
+ * the single-depth lockdep subclass.
+ */
+#define snd_pcm_stream_lock_irqsave_nested(substream, flags)		\
+	do {								\
+		typecheck(unsigned long, flags);			\
+		flags = _snd_pcm_stream_lock_irqsave_nested(substream); \
+	} while (0)
+
+/**
  * snd_pcm_group_for_each_entry - iterate over the linked substreams
  * @s: the iterator
  * @substream: the substream
@@ -658,12 +677,26 @@
  */
 static inline int snd_pcm_running(struct snd_pcm_substream *substream)
 {
-	return (substream->runtime->status->state == SNDRV_PCM_STATE_RUNNING ||
-		(substream->runtime->status->state == SNDRV_PCM_STATE_DRAINING &&
+	return (substream->runtime->state == SNDRV_PCM_STATE_RUNNING ||
+		(substream->runtime->state == SNDRV_PCM_STATE_DRAINING &&
 		 substream->stream == SNDRV_PCM_STREAM_PLAYBACK));
 }
 
 /**
+ * __snd_pcm_set_state - Change the current PCM state
+ * @runtime: PCM runtime to set
+ * @state: the current state to set
+ *
+ * Call within the stream lock
+ */
+static inline void __snd_pcm_set_state(struct snd_pcm_runtime *runtime,
+				       snd_pcm_state_t state)
+{
+	runtime->state = state;
+	runtime->status->state = state; /* copy for mmap */
+}
+
+/**
  * bytes_to_samples - Unit conversion of the size from bytes to samples
  * @runtime: PCM runtime instance
  * @size: size in bytes
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/soc-card.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/soc-card.h
@@ -40,6 +40,43 @@
 void snd_soc_card_remove_dai_link(struct snd_soc_card *card,
 				  struct snd_soc_dai_link *dai_link);
 
+#ifdef CONFIG_PCI
+static inline void snd_soc_card_set_pci_ssid(struct snd_soc_card *card,
+					     unsigned short vendor,
+					     unsigned short device)
+{
+	card->pci_subsystem_vendor = vendor;
+	card->pci_subsystem_device = device;
+	card->pci_subsystem_set = true;
+}
+
+static inline int snd_soc_card_get_pci_ssid(struct snd_soc_card *card,
+					    unsigned short *vendor,
+					    unsigned short *device)
+{
+	if (!card->pci_subsystem_set)
+		return -ENOENT;
+
+	*vendor = card->pci_subsystem_vendor;
+	*device = card->pci_subsystem_device;
+
+	return 0;
+}
+#else /* !CONFIG_PCI */
+static inline void snd_soc_card_set_pci_ssid(struct snd_soc_card *card,
+					     unsigned short vendor,
+					     unsigned short device)
+{
+}
+
+static inline int snd_soc_card_get_pci_ssid(struct snd_soc_card *card,
+					    unsigned short *vendor,
+					    unsigned short *device)
+{
+	return -ENOENT;
+}
+#endif /* CONFIG_PCI */
+
 /* device driver data */
 static inline void snd_soc_card_set_drvdata(struct snd_soc_card *card,
 					    void *data)
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/soc-dai.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/soc-dai.h
@@ -295,9 +295,9 @@
 			unsigned int *rx_num, unsigned int *rx_slot);
 	int (*set_tristate)(struct snd_soc_dai *dai, int tristate);
 
-	int (*set_sdw_stream)(struct snd_soc_dai *dai,
-			void *stream, int direction);
-	void *(*get_sdw_stream)(struct snd_soc_dai *dai, int direction);
+	int (*set_stream)(struct snd_soc_dai *dai,
+			  void *stream, int direction);
+	void *(*get_stream)(struct snd_soc_dai *dai, int direction);
 
 	/*
 	 * DAI digital mute - optional.
@@ -515,42 +515,42 @@
 }
 
 /**
- * snd_soc_dai_set_sdw_stream() - Configures a DAI for SDW stream operation
+ * snd_soc_dai_set_stream() - Configures a DAI for stream operation
  * @dai: DAI
- * @stream: STREAM
+ * @stream: STREAM (opaque structure depending on DAI type)
  * @direction: Stream direction(Playback/Capture)
- * SoundWire subsystem doesn't have a notion of direction and we reuse
+ * Some subsystems, such as SoundWire, don't have a notion of direction and we reuse
  * the ASoC stream direction to configure sink/source ports.
  * Playback maps to source ports and Capture for sink ports.
  *
  * This should be invoked with NULL to clear the stream set previously.
  * Returns 0 on success, a negative error code otherwise.
  */
-static inline int snd_soc_dai_set_sdw_stream(struct snd_soc_dai *dai,
-				void *stream, int direction)
+static inline int snd_soc_dai_set_stream(struct snd_soc_dai *dai,
+					 void *stream, int direction)
 {
-	if (dai->driver->ops->set_sdw_stream)
-		return dai->driver->ops->set_sdw_stream(dai, stream, direction);
+	if (dai->driver->ops->set_stream)
+		return dai->driver->ops->set_stream(dai, stream, direction);
 	else
 		return -ENOTSUPP;
 }
 
 /**
- * snd_soc_dai_get_sdw_stream() - Retrieves SDW stream from DAI
+ * snd_soc_dai_get_stream() - Retrieves stream from DAI
  * @dai: DAI
  * @direction: Stream direction(Playback/Capture)
  *
  * This routine only retrieves that was previously configured
- * with snd_soc_dai_get_sdw_stream()
+ * with snd_soc_dai_get_stream()
  *
  * Returns pointer to stream or an ERR_PTR value, e.g.
  * ERR_PTR(-ENOTSUPP) if callback is not supported;
  */
-static inline void *snd_soc_dai_get_sdw_stream(struct snd_soc_dai *dai,
-					       int direction)
+static inline void *snd_soc_dai_get_stream(struct snd_soc_dai *dai,
+					   int direction)
 {
-	if (dai->driver->ops->get_sdw_stream)
-		return dai->driver->ops->get_sdw_stream(dai, direction);
+	if (dai->driver->ops->get_stream)
+		return dai->driver->ops->get_stream(dai, direction);
 	else
 		return ERR_PTR(-ENOTSUPP);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/soc-dapm.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/soc-dapm.h
@@ -16,6 +16,7 @@
 #include <sound/asoc.h>
 
 struct device;
+struct snd_pcm_substream;
 struct snd_soc_pcm_runtime;
 struct soc_enum;
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/soc-dpcm.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/soc-dpcm.h
@@ -101,6 +101,8 @@
 	enum snd_soc_dpcm_state state;
 
 	int trigger_pending; /* trigger cmd + 1 if pending, 0 if not */
+
+	int be_start; /* refcount protected by BE stream pcm lock */
 };
 
 #define for_each_dpcm_fe(be, stream, _dpcm)				\
@@ -121,6 +123,10 @@
 int snd_soc_dpcm_can_be_params(struct snd_soc_pcm_runtime *fe,
 		struct snd_soc_pcm_runtime *be, int stream);
 
+/* can this BE perform prepare */
+int snd_soc_dpcm_can_be_prepared(struct snd_soc_pcm_runtime *fe,
+				 struct snd_soc_pcm_runtime *be, int stream);
+
 /* is the current PCM operation for this FE ? */
 int snd_soc_dpcm_fe_can_update(struct snd_soc_pcm_runtime *fe, int stream);
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/soc-topology.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/soc-topology.h
@@ -188,8 +188,7 @@
 
 #else
 
-static inline int snd_soc_tplg_component_remove(struct snd_soc_component *comp,
-						u32 index)
+static inline int snd_soc_tplg_component_remove(struct snd_soc_component *comp)
 {
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/sound/soc.h
+++ linux-xilinx-zynqmp-5.15.0/include/sound/soc.h
@@ -880,6 +880,17 @@
 #ifdef CONFIG_DMI
 	char dmi_longname[80];
 #endif /* CONFIG_DMI */
+
+#ifdef CONFIG_PCI
+	/*
+	 * PCI does not define 0 as invalid, so pci_subsystem_set indicates
+	 * whether a value has been written to these fields.
+	 */
+	unsigned short pci_subsystem_vendor;
+	unsigned short pci_subsystem_device;
+	bool pci_subsystem_set;
+#endif /* CONFIG_PCI */
+
 	char topology_shortname[32];
 
 	struct device *dev;
@@ -893,8 +904,6 @@
 	struct mutex pcm_mutex;
 	enum snd_soc_pcm_subclass pcm_subclass;
 
-	spinlock_t dpcm_lock;
-
 	int (*probe)(struct snd_soc_card *card);
 	int (*late_probe)(struct snd_soc_card *card);
 	int (*remove)(struct snd_soc_card *card);
@@ -1104,7 +1113,10 @@
 
 /* mixer control */
 struct soc_mixer_control {
-	int min, max, platform_max;
+	/* Minimum and maximum specified as written to the hardware */
+	int min, max;
+	/* Limited maximum value specified as presented through the control */
+	int platform_max;
 	int reg, rreg;
 	unsigned int shift, rshift;
 	unsigned int sign_bit;
--- linux-xilinx-zynqmp-5.15.0.orig/include/target/target_core_base.h
+++ linux-xilinx-zynqmp-5.15.0/include/target/target_core_base.h
@@ -812,8 +812,9 @@
 	atomic_long_t		read_bytes;
 	atomic_long_t		write_bytes;
 	/* Active commands on this virtual SE device */
-	atomic_t		simple_cmds;
-	atomic_t		dev_ordered_sync;
+	atomic_t		non_ordered;
+	bool			ordered_sync_in_progress;
+	atomic_t		delayed_cmd_count;
 	atomic_t		dev_qf_count;
 	u32			export_count;
 	spinlock_t		delayed_cmd_lock;
@@ -834,6 +835,7 @@
 	struct list_head	dev_sep_list;
 	struct list_head	dev_tmr_list;
 	struct work_struct	qf_work_queue;
+	struct work_struct	delayed_cmd_work;
 	struct list_head	delayed_cmd_list;
 	struct list_head	qf_cmd_list;
 	/* Pointer to associated SE HBA */
@@ -863,6 +865,7 @@
 	struct rcu_head		rcu_head;
 	int			queue_cnt;
 	struct se_device_queue	*queues;
+	struct mutex		lun_reset_mutex;
 };
 
 struct se_hba {
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/bpf_probe.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/bpf_probe.h
@@ -21,6 +21,28 @@
 #undef __get_bitmask
 #define __get_bitmask(field) (char *)__get_dynamic_array(field)
 
+#undef __get_sockaddr
+#define __get_sockaddr(field) ((struct sockaddr *)__get_dynamic_array(field))
+
+#undef __get_rel_dynamic_array
+#define __get_rel_dynamic_array(field)	\
+		((void *)(&__entry->__rel_loc_##field) +	\
+		 sizeof(__entry->__rel_loc_##field) +		\
+		 (__entry->__rel_loc_##field & 0xffff))
+
+#undef __get_rel_dynamic_array_len
+#define __get_rel_dynamic_array_len(field)	\
+		((__entry->__rel_loc_##field >> 16) & 0xffff)
+
+#undef __get_rel_str
+#define __get_rel_str(field) ((char *)__get_rel_dynamic_array(field))
+
+#undef __get_rel_bitmask
+#define __get_rel_bitmask(field) (char *)__get_rel_dynamic_array(field)
+
+#undef __get_rel_sockaddr
+#define __get_rel_sockaddr(field) ((struct sockaddr *)__get_rel_dynamic_array(field))
+
 #undef __perf_count
 #define __perf_count(c)	(c)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/afs.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/afs.h
@@ -728,14 +728,14 @@
 
 TRACE_EVENT(afs_call,
 	    TP_PROTO(struct afs_call *call, enum afs_call_trace op,
-		     int usage, int outstanding, const void *where),
+		     int ref, int outstanding, const void *where),
 
-	    TP_ARGS(call, op, usage, outstanding, where),
+	    TP_ARGS(call, op, ref, outstanding, where),
 
 	    TP_STRUCT__entry(
 		    __field(unsigned int,		call		)
 		    __field(int,			op		)
-		    __field(int,			usage		)
+		    __field(int,			ref		)
 		    __field(int,			outstanding	)
 		    __field(const void *,		where		)
 			     ),
@@ -743,15 +743,15 @@
 	    TP_fast_assign(
 		    __entry->call = call->debug_id;
 		    __entry->op = op;
-		    __entry->usage = usage;
+		    __entry->ref = ref;
 		    __entry->outstanding = outstanding;
 		    __entry->where = where;
 			   ),
 
-	    TP_printk("c=%08x %s u=%d o=%d sp=%pSR",
+	    TP_printk("c=%08x %s r=%d o=%d sp=%pSR",
 		      __entry->call,
 		      __print_symbolic(__entry->op, afs_call_traces),
-		      __entry->usage,
+		      __entry->ref,
 		      __entry->outstanding,
 		      __entry->where)
 	    );
@@ -1475,36 +1475,36 @@
 		    __entry->reason = reason;
 			   ),
 
-	    TP_printk("V=%llx %s u=%d",
+	    TP_printk("V=%llx %s ur=%d",
 		      __entry->vid,
 		      __print_symbolic(__entry->reason, afs_volume_traces),
 		      __entry->ref)
 	    );
 
 TRACE_EVENT(afs_cell,
-	    TP_PROTO(unsigned int cell_debug_id, int usage, int active,
+	    TP_PROTO(unsigned int cell_debug_id, int ref, int active,
 		     enum afs_cell_trace reason),
 
-	    TP_ARGS(cell_debug_id, usage, active, reason),
+	    TP_ARGS(cell_debug_id, ref, active, reason),
 
 	    TP_STRUCT__entry(
 		    __field(unsigned int,		cell		)
-		    __field(int,			usage		)
+		    __field(int,			ref		)
 		    __field(int,			active		)
 		    __field(int,			reason		)
 			     ),
 
 	    TP_fast_assign(
 		    __entry->cell = cell_debug_id;
-		    __entry->usage = usage;
+		    __entry->ref = ref;
 		    __entry->active = active;
 		    __entry->reason = reason;
 			   ),
 
-	    TP_printk("L=%08x %s u=%d a=%d",
+	    TP_printk("L=%08x %s r=%d a=%d",
 		      __entry->cell,
 		      __print_symbolic(__entry->reason, afs_cell_traces),
-		      __entry->usage,
+		      __entry->ref,
 		      __entry->active)
 	    );
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/asoc.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/asoc.h
@@ -12,6 +12,8 @@
 #define DAPM_DIRECT "(direct)"
 #define DAPM_ARROW(dir) (((dir) == SND_SOC_DAPM_DIR_OUT) ? "->" : "<-")
 
+TRACE_DEFINE_ENUM(SND_SOC_DAPM_DIR_OUT);
+
 struct snd_soc_jack;
 struct snd_soc_card;
 struct snd_soc_dapm_widget;
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/btrfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/btrfs.h
@@ -96,7 +96,7 @@
 	EM( FLUSH_DELALLOC_WAIT,	"FLUSH_DELALLOC_WAIT")		\
 	EM( FLUSH_DELALLOC_FULL,	"FLUSH_DELALLOC_FULL")		\
 	EM( FLUSH_DELAYED_REFS_NR,	"FLUSH_DELAYED_REFS_NR")	\
-	EM( FLUSH_DELAYED_REFS,		"FLUSH_ELAYED_REFS")		\
+	EM( FLUSH_DELAYED_REFS,		"FLUSH_DELAYED_REFS")		\
 	EM( ALLOC_CHUNK,		"ALLOC_CHUNK")			\
 	EM( ALLOC_CHUNK_FORCE,		"ALLOC_CHUNK_FORCE")		\
 	EM( RUN_DELAYED_IPUTS,		"RUN_DELAYED_IPUTS")		\
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/cgroup.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/cgroup.h
@@ -59,8 +59,8 @@
 
 	TP_STRUCT__entry(
 		__field(	int,		root			)
-		__field(	int,		id			)
 		__field(	int,		level			)
+		__field(	u64,		id			)
 		__string(	path,		path			)
 	),
 
@@ -71,7 +71,7 @@
 		__assign_str(path, path);
 	),
 
-	TP_printk("root=%d id=%d level=%d path=%s",
+	TP_printk("root=%d id=%llu level=%d path=%s",
 		  __entry->root, __entry->id, __entry->level, __get_str(path))
 );
 
@@ -126,8 +126,8 @@
 
 	TP_STRUCT__entry(
 		__field(	int,		dst_root		)
-		__field(	int,		dst_id			)
 		__field(	int,		dst_level		)
+		__field(	u64,		dst_id			)
 		__field(	int,		pid			)
 		__string(	dst_path,	path			)
 		__string(	comm,		task->comm		)
@@ -142,7 +142,7 @@
 		__assign_str(comm, task->comm);
 	),
 
-	TP_printk("dst_root=%d dst_id=%d dst_level=%d dst_path=%s pid=%d comm=%s",
+	TP_printk("dst_root=%d dst_id=%llu dst_level=%d dst_path=%s pid=%d comm=%s",
 		  __entry->dst_root, __entry->dst_id, __entry->dst_level,
 		  __get_str(dst_path), __entry->pid, __get_str(comm))
 );
@@ -171,8 +171,8 @@
 
 	TP_STRUCT__entry(
 		__field(	int,		root			)
-		__field(	int,		id			)
 		__field(	int,		level			)
+		__field(	u64,		id			)
 		__string(	path,		path			)
 		__field(	int,		val			)
 	),
@@ -185,7 +185,7 @@
 		__entry->val = val;
 	),
 
-	TP_printk("root=%d id=%d level=%d path=%s val=%d",
+	TP_printk("root=%d id=%llu level=%d path=%s val=%d",
 		  __entry->root, __entry->id, __entry->level, __get_str(path),
 		  __entry->val)
 );
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/ext4.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/ext4.h
@@ -95,6 +95,18 @@
 	{ FALLOC_FL_COLLAPSE_RANGE,	"COLLAPSE_RANGE"},	\
 	{ FALLOC_FL_ZERO_RANGE,		"ZERO_RANGE"})
 
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_XATTR);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_CROSS_RENAME);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_JOURNAL_FLAG_CHANGE);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_NOMEM);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_SWAP_BOOT);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_RESIZE);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_RENAME_DIR);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_FALLOC_RANGE);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_INODE_JOURNAL_DATA);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_ENCRYPTED_FILENAME);
+TRACE_DEFINE_ENUM(EXT4_FC_REASON_MAX);
+
 #define show_fc_reason(reason)						\
 	__print_symbolic(reason,					\
 		{ EXT4_FC_REASON_XATTR,		"XATTR"},		\
@@ -105,7 +117,8 @@
 		{ EXT4_FC_REASON_RESIZE,	"RESIZE"},		\
 		{ EXT4_FC_REASON_RENAME_DIR,	"RENAME_DIR"},		\
 		{ EXT4_FC_REASON_FALLOC_RANGE,	"FALLOC_RANGE"},	\
-		{ EXT4_FC_REASON_INODE_JOURNAL_DATA,	"INODE_JOURNAL_DATA"})
+		{ EXT4_FC_REASON_INODE_JOURNAL_DATA,	"INODE_JOURNAL_DATA"}, \
+		{ EXT4_FC_REASON_ENCRYPTED_FILENAME,	"ENCRYPTED_FILENAME"})
 
 TRACE_EVENT(ext4_other_inode_update_time,
 	TP_PROTO(struct inode *inode, ino_t orig_ino),
@@ -2723,41 +2736,51 @@
 
 #define FC_REASON_NAME_STAT(reason)					\
 	show_fc_reason(reason),						\
-	__entry->sbi->s_fc_stats.fc_ineligible_reason_count[reason]
+	__entry->fc_ineligible_rc[reason]
 
 TRACE_EVENT(ext4_fc_stats,
-	    TP_PROTO(struct super_block *sb),
+	TP_PROTO(struct super_block *sb),
+
+	TP_ARGS(sb),
+
+	TP_STRUCT__entry(
+		__field(dev_t, dev)
+		__array(unsigned int, fc_ineligible_rc, EXT4_FC_REASON_MAX)
+		__field(unsigned long, fc_commits)
+		__field(unsigned long, fc_ineligible_commits)
+		__field(unsigned long, fc_numblks)
+	),
 
-	    TP_ARGS(sb),
+	TP_fast_assign(
+		int i;
 
-	    TP_STRUCT__entry(
-		    __field(dev_t, dev)
-		    __field(struct ext4_sb_info *, sbi)
-		    __field(int, count)
-		    ),
-
-	    TP_fast_assign(
-		    __entry->dev = sb->s_dev;
-		    __entry->sbi = EXT4_SB(sb);
-		    ),
-
-	    TP_printk("dev %d:%d fc ineligible reasons:\n"
-		      "%s:%d, %s:%d, %s:%d, %s:%d, %s:%d, %s:%d, %s:%d, %s:%d, %s:%d; "
-		      "num_commits:%ld, ineligible: %ld, numblks: %ld",
-		      MAJOR(__entry->dev), MINOR(__entry->dev),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_XATTR),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_CROSS_RENAME),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_JOURNAL_FLAG_CHANGE),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_NOMEM),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_SWAP_BOOT),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_RESIZE),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_RENAME_DIR),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_FALLOC_RANGE),
-		      FC_REASON_NAME_STAT(EXT4_FC_REASON_INODE_JOURNAL_DATA),
-		      __entry->sbi->s_fc_stats.fc_num_commits,
-		      __entry->sbi->s_fc_stats.fc_ineligible_commits,
-		      __entry->sbi->s_fc_stats.fc_numblks)
+		__entry->dev = sb->s_dev;
+		for (i = 0; i < EXT4_FC_REASON_MAX; i++) {
+			__entry->fc_ineligible_rc[i] =
+				EXT4_SB(sb)->s_fc_stats.fc_ineligible_reason_count[i];
+		}
+		__entry->fc_commits = EXT4_SB(sb)->s_fc_stats.fc_num_commits;
+		__entry->fc_ineligible_commits =
+			EXT4_SB(sb)->s_fc_stats.fc_ineligible_commits;
+		__entry->fc_numblks = EXT4_SB(sb)->s_fc_stats.fc_numblks;
+	),
 
+	TP_printk("dev %d,%d fc ineligible reasons:\n"
+		  "%s:%u, %s:%u, %s:%u, %s:%u, %s:%u, %s:%u, %s:%u, %s:%u, %s:%u, %s:%u"
+		  "num_commits:%lu, ineligible: %lu, numblks: %lu",
+		  MAJOR(__entry->dev), MINOR(__entry->dev),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_XATTR),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_CROSS_RENAME),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_JOURNAL_FLAG_CHANGE),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_NOMEM),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_SWAP_BOOT),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_RESIZE),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_RENAME_DIR),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_FALLOC_RANGE),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_INODE_JOURNAL_DATA),
+		  FC_REASON_NAME_STAT(EXT4_FC_REASON_ENCRYPTED_FILENAME),
+		  __entry->fc_commits, __entry->fc_ineligible_commits,
+		  __entry->fc_numblks)
 );
 
 #define DEFINE_TRACE_DENTRY_EVENT(__type)				\
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/f2fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/f2fs.h
@@ -145,7 +145,8 @@
 		{ CP_NODE_NEED_CP,	"node needs cp" },		\
 		{ CP_FASTBOOT_MODE,	"fastboot mode" },		\
 		{ CP_SPEC_LOG_NUM,	"log type is 2" },		\
-		{ CP_RECOVER_DIR,	"dir needs recovery" })
+		{ CP_RECOVER_DIR,	"dir needs recovery" },		\
+		{ CP_XATTR_DIR,		"dir's xattr updated" })
 
 #define show_shutdown_mode(type)					\
 	__print_symbolic(type,						\
@@ -513,7 +514,7 @@
 	TP_STRUCT__entry(
 		__field(dev_t,	dev)
 		__field(ino_t,	ino)
-		__field(nid_t,	nid[3])
+		__array(nid_t,	nid, 3)
 		__field(int,	depth)
 		__field(int,	err)
 	),
@@ -540,17 +541,17 @@
 
 TRACE_EVENT(f2fs_file_write_iter,
 
-	TP_PROTO(struct inode *inode, unsigned long offset,
-		unsigned long length, int ret),
+	TP_PROTO(struct inode *inode, loff_t offset, size_t length,
+		 ssize_t ret),
 
 	TP_ARGS(inode, offset, length, ret),
 
 	TP_STRUCT__entry(
 		__field(dev_t,	dev)
 		__field(ino_t,	ino)
-		__field(unsigned long, offset)
-		__field(unsigned long, length)
-		__field(int,	ret)
+		__field(loff_t, offset)
+		__field(size_t, length)
+		__field(ssize_t, ret)
 	),
 
 	TP_fast_assign(
@@ -562,7 +563,7 @@
 	),
 
 	TP_printk("dev = (%d,%d), ino = %lu, "
-		"offset = %lu, length = %lu, written(err) = %d",
+		"offset = %lld, length = %zu, written(err) = %zd",
 		show_dev_ino(__entry),
 		__entry->offset,
 		__entry->length,
@@ -570,9 +571,10 @@
 );
 
 TRACE_EVENT(f2fs_map_blocks,
-	TP_PROTO(struct inode *inode, struct f2fs_map_blocks *map, int ret),
+	TP_PROTO(struct inode *inode, struct f2fs_map_blocks *map,
+				int create, int flag, int ret),
 
-	TP_ARGS(inode, map, ret),
+	TP_ARGS(inode, map, create, flag, ret),
 
 	TP_STRUCT__entry(
 		__field(dev_t,	dev)
@@ -583,11 +585,14 @@
 		__field(unsigned int,	m_flags)
 		__field(int,	m_seg_type)
 		__field(bool,	m_may_create)
+		__field(bool,	m_multidev_dio)
+		__field(int,	create)
+		__field(int,	flag)
 		__field(int,	ret)
 	),
 
 	TP_fast_assign(
-		__entry->dev		= inode->i_sb->s_dev;
+		__entry->dev		= map->m_bdev->bd_dev;
 		__entry->ino		= inode->i_ino;
 		__entry->m_lblk		= map->m_lblk;
 		__entry->m_pblk		= map->m_pblk;
@@ -595,12 +600,16 @@
 		__entry->m_flags	= map->m_flags;
 		__entry->m_seg_type	= map->m_seg_type;
 		__entry->m_may_create	= map->m_may_create;
+		__entry->m_multidev_dio	= map->m_multidev_dio;
+		__entry->create		= create;
+		__entry->flag		= flag;
 		__entry->ret		= ret;
 	),
 
 	TP_printk("dev = (%d,%d), ino = %lu, file offset = %llu, "
-		"start blkaddr = 0x%llx, len = 0x%llx, flags = %u,"
-		"seg_type = %d, may_create = %d, err = %d",
+		"start blkaddr = 0x%llx, len = 0x%llx, flags = %u, "
+		"seg_type = %d, may_create = %d, multidevice = %d, "
+		"create = %d, flag = %d, err = %d",
 		show_dev_ino(__entry),
 		(unsigned long long)__entry->m_lblk,
 		(unsigned long long)__entry->m_pblk,
@@ -608,6 +617,9 @@
 		__entry->m_flags,
 		__entry->m_seg_type,
 		__entry->m_may_create,
+		__entry->m_multidev_dio,
+		__entry->create,
+		__entry->flag,
 		__entry->ret)
 );
 
@@ -807,20 +819,20 @@
 	TP_STRUCT__entry(
 		__field(dev_t,	dev)
 		__field(ino_t,	ino)
-		__field(const char *,	name)
+		__string(name,	dentry->d_name.name)
 		__field(unsigned int, flags)
 	),
 
 	TP_fast_assign(
 		__entry->dev	= dir->i_sb->s_dev;
 		__entry->ino	= dir->i_ino;
-		__entry->name	= dentry->d_name.name;
+		__assign_str(name, dentry->d_name.name);
 		__entry->flags	= flags;
 	),
 
 	TP_printk("dev = (%d,%d), pino = %lu, name:%s, flags:%u",
 		show_dev_ino(__entry),
-		__entry->name,
+		__get_str(name),
 		__entry->flags)
 );
 
@@ -834,7 +846,7 @@
 	TP_STRUCT__entry(
 		__field(dev_t,	dev)
 		__field(ino_t,	ino)
-		__field(const char *,	name)
+		__string(name,	dentry->d_name.name)
 		__field(nid_t,	cino)
 		__field(int,	err)
 	),
@@ -842,14 +854,14 @@
 	TP_fast_assign(
 		__entry->dev	= dir->i_sb->s_dev;
 		__entry->ino	= dir->i_ino;
-		__entry->name	= dentry->d_name.name;
+		__assign_str(name, dentry->d_name.name);
 		__entry->cino	= ino;
 		__entry->err	= err;
 	),
 
 	TP_printk("dev = (%d,%d), pino = %lu, name:%s, ino:%u, err:%d",
 		show_dev_ino(__entry),
-		__entry->name,
+		__get_str(name),
 		__entry->cino,
 		__entry->err)
 );
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/ib_mad.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/ib_mad.h
@@ -49,7 +49,6 @@
 		__field(int,            retries_left)
 		__field(int,            max_retries)
 		__field(int,            retry)
-		__field(u16,            pkey)
 	),
 
 	TP_fast_assign(
@@ -89,7 +88,7 @@
 		  "hdr : base_ver 0x%x class 0x%x class_ver 0x%x " \
 		  "method 0x%x status 0x%x class_specific 0x%x tid 0x%llx " \
 		  "attr_id 0x%x attr_mod 0x%x  => dlid 0x%08x sl %d "\
-		  "pkey 0x%x rpqn 0x%x rqpkey 0x%x",
+		  "rpqn 0x%x rqpkey 0x%x",
 		__entry->dev_index, __entry->port_num, __entry->qp_num,
 		__entry->agent_priv, be64_to_cpu(__entry->wrtid),
 		__entry->retries_left, __entry->max_retries,
@@ -100,7 +99,7 @@
 		be16_to_cpu(__entry->class_specific),
 		be64_to_cpu(__entry->tid), be16_to_cpu(__entry->attr_id),
 		be32_to_cpu(__entry->attr_mod),
-		be32_to_cpu(__entry->dlid), __entry->sl, __entry->pkey,
+		be32_to_cpu(__entry->dlid), __entry->sl,
 		__entry->rqpn, __entry->rqkey
 	)
 );
@@ -204,7 +203,6 @@
 		__field(u16,            wc_status)
 		__field(u32,            slid)
 		__field(u32,            dev_index)
-		__field(u16,            pkey)
 	),
 
 	TP_fast_assign(
@@ -224,9 +222,6 @@
 		__entry->slid = wc->slid;
 		__entry->src_qp = wc->src_qp;
 		__entry->sl = wc->sl;
-		ib_query_pkey(qp_info->port_priv->device,
-			      qp_info->port_priv->port_num,
-			      wc->pkey_index, &__entry->pkey);
 		__entry->wc_status = wc->status;
 	),
 
@@ -234,7 +229,7 @@
 		  "base_ver 0x%02x class 0x%02x class_ver 0x%02x " \
 		  "method 0x%02x status 0x%04x class_specific 0x%04x " \
 		  "tid 0x%016llx attr_id 0x%04x attr_mod 0x%08x " \
-		  "slid 0x%08x src QP%d, sl %d pkey 0x%04x",
+		  "slid 0x%08x src QP%d, sl %d",
 		__entry->dev_index, __entry->port_num, __entry->qp_num,
 		__entry->wc_status,
 		__entry->length,
@@ -244,7 +239,7 @@
 		be16_to_cpu(__entry->class_specific),
 		be64_to_cpu(__entry->tid), be16_to_cpu(__entry->attr_id),
 		be32_to_cpu(__entry->attr_mod),
-		__entry->slid, __entry->src_qp, __entry->sl, __entry->pkey
+		__entry->slid, __entry->src_qp, __entry->sl
 	)
 );
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/jbd2.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/jbd2.h
@@ -40,7 +40,7 @@
 	TP_STRUCT__entry(
 		__field(	dev_t,	dev			)
 		__field(	char,	sync_commit		  )
-		__field(	int,	transaction		  )
+		__field(	tid_t,	transaction		  )
 	),
 
 	TP_fast_assign(
@@ -49,7 +49,7 @@
 		__entry->transaction	= commit_transaction->t_tid;
 	),
 
-	TP_printk("dev %d,%d transaction %d sync %d",
+	TP_printk("dev %d,%d transaction %u sync %d",
 		  MAJOR(__entry->dev), MINOR(__entry->dev),
 		  __entry->transaction, __entry->sync_commit)
 );
@@ -97,8 +97,8 @@
 	TP_STRUCT__entry(
 		__field(	dev_t,	dev			)
 		__field(	char,	sync_commit		  )
-		__field(	int,	transaction		  )
-		__field(	int,	head		  	  )
+		__field(	tid_t,	transaction		  )
+		__field(	tid_t,	head		  	  )
 	),
 
 	TP_fast_assign(
@@ -108,7 +108,7 @@
 		__entry->head		= journal->j_tail_sequence;
 	),
 
-	TP_printk("dev %d,%d transaction %d sync %d head %d",
+	TP_printk("dev %d,%d transaction %u sync %d head %u",
 		  MAJOR(__entry->dev), MINOR(__entry->dev),
 		  __entry->transaction, __entry->sync_commit, __entry->head)
 );
@@ -134,14 +134,14 @@
 );
 
 DECLARE_EVENT_CLASS(jbd2_handle_start_class,
-	TP_PROTO(dev_t dev, unsigned long tid, unsigned int type,
+	TP_PROTO(dev_t dev, tid_t tid, unsigned int type,
 		 unsigned int line_no, int requested_blocks),
 
 	TP_ARGS(dev, tid, type, line_no, requested_blocks),
 
 	TP_STRUCT__entry(
 		__field(		dev_t,	dev		)
-		__field(	unsigned long,	tid		)
+		__field(		tid_t,	tid		)
 		__field(	 unsigned int,	type		)
 		__field(	 unsigned int,	line_no		)
 		__field(		  int,	requested_blocks)
@@ -155,28 +155,28 @@
 		__entry->requested_blocks = requested_blocks;
 	),
 
-	TP_printk("dev %d,%d tid %lu type %u line_no %u "
+	TP_printk("dev %d,%d tid %u type %u line_no %u "
 		  "requested_blocks %d",
 		  MAJOR(__entry->dev), MINOR(__entry->dev), __entry->tid,
 		  __entry->type, __entry->line_no, __entry->requested_blocks)
 );
 
 DEFINE_EVENT(jbd2_handle_start_class, jbd2_handle_start,
-	TP_PROTO(dev_t dev, unsigned long tid, unsigned int type,
+	TP_PROTO(dev_t dev, tid_t tid, unsigned int type,
 		 unsigned int line_no, int requested_blocks),
 
 	TP_ARGS(dev, tid, type, line_no, requested_blocks)
 );
 
 DEFINE_EVENT(jbd2_handle_start_class, jbd2_handle_restart,
-	TP_PROTO(dev_t dev, unsigned long tid, unsigned int type,
+	TP_PROTO(dev_t dev, tid_t tid, unsigned int type,
 		 unsigned int line_no, int requested_blocks),
 
 	TP_ARGS(dev, tid, type, line_no, requested_blocks)
 );
 
 TRACE_EVENT(jbd2_handle_extend,
-	TP_PROTO(dev_t dev, unsigned long tid, unsigned int type,
+	TP_PROTO(dev_t dev, tid_t tid, unsigned int type,
 		 unsigned int line_no, int buffer_credits,
 		 int requested_blocks),
 
@@ -184,7 +184,7 @@
 
 	TP_STRUCT__entry(
 		__field(		dev_t,	dev		)
-		__field(	unsigned long,	tid		)
+		__field(		tid_t,	tid		)
 		__field(	 unsigned int,	type		)
 		__field(	 unsigned int,	line_no		)
 		__field(		  int,	buffer_credits  )
@@ -200,7 +200,7 @@
 		__entry->requested_blocks = requested_blocks;
 	),
 
-	TP_printk("dev %d,%d tid %lu type %u line_no %u "
+	TP_printk("dev %d,%d tid %u type %u line_no %u "
 		  "buffer_credits %d requested_blocks %d",
 		  MAJOR(__entry->dev), MINOR(__entry->dev), __entry->tid,
 		  __entry->type, __entry->line_no, __entry->buffer_credits,
@@ -208,7 +208,7 @@
 );
 
 TRACE_EVENT(jbd2_handle_stats,
-	TP_PROTO(dev_t dev, unsigned long tid, unsigned int type,
+	TP_PROTO(dev_t dev, tid_t tid, unsigned int type,
 		 unsigned int line_no, int interval, int sync,
 		 int requested_blocks, int dirtied_blocks),
 
@@ -217,7 +217,7 @@
 
 	TP_STRUCT__entry(
 		__field(		dev_t,	dev		)
-		__field(	unsigned long,	tid		)
+		__field(		tid_t,	tid		)
 		__field(	 unsigned int,	type		)
 		__field(	 unsigned int,	line_no		)
 		__field(		  int,	interval	)
@@ -237,7 +237,7 @@
 		__entry->dirtied_blocks	  = dirtied_blocks;
 	),
 
-	TP_printk("dev %d,%d tid %lu type %u line_no %u interval %d "
+	TP_printk("dev %d,%d tid %u type %u line_no %u interval %d "
 		  "sync %d requested_blocks %d dirtied_blocks %d",
 		  MAJOR(__entry->dev), MINOR(__entry->dev), __entry->tid,
 		  __entry->type, __entry->line_no, __entry->interval,
@@ -246,14 +246,14 @@
 );
 
 TRACE_EVENT(jbd2_run_stats,
-	TP_PROTO(dev_t dev, unsigned long tid,
+	TP_PROTO(dev_t dev, tid_t tid,
 		 struct transaction_run_stats_s *stats),
 
 	TP_ARGS(dev, tid, stats),
 
 	TP_STRUCT__entry(
 		__field(		dev_t,	dev		)
-		__field(	unsigned long,	tid		)
+		__field(		tid_t,	tid		)
 		__field(	unsigned long,	wait		)
 		__field(	unsigned long,	request_delay	)
 		__field(	unsigned long,	running		)
@@ -279,7 +279,7 @@
 		__entry->blocks_logged	= stats->rs_blocks_logged;
 	),
 
-	TP_printk("dev %d,%d tid %lu wait %u request_delay %u running %u "
+	TP_printk("dev %d,%d tid %u wait %u request_delay %u running %u "
 		  "locked %u flushing %u logging %u handle_count %u "
 		  "blocks %u blocks_logged %u",
 		  MAJOR(__entry->dev), MINOR(__entry->dev), __entry->tid,
@@ -294,14 +294,14 @@
 );
 
 TRACE_EVENT(jbd2_checkpoint_stats,
-	TP_PROTO(dev_t dev, unsigned long tid,
+	TP_PROTO(dev_t dev, tid_t tid,
 		 struct transaction_chp_stats_s *stats),
 
 	TP_ARGS(dev, tid, stats),
 
 	TP_STRUCT__entry(
 		__field(		dev_t,	dev		)
-		__field(	unsigned long,	tid		)
+		__field(		tid_t,	tid		)
 		__field(	unsigned long,	chp_time	)
 		__field(		__u32,	forced_to_close	)
 		__field(		__u32,	written		)
@@ -317,7 +317,7 @@
 		__entry->dropped	= stats->cs_dropped;
 	),
 
-	TP_printk("dev %d,%d tid %lu chp_time %u forced_to_close %u "
+	TP_printk("dev %d,%d tid %u chp_time %u forced_to_close %u "
 		  "written %u dropped %u",
 		  MAJOR(__entry->dev), MINOR(__entry->dev), __entry->tid,
 		  jiffies_to_msecs(__entry->chp_time),
@@ -462,11 +462,9 @@
 TRACE_EVENT(jbd2_shrink_checkpoint_list,
 
 	TP_PROTO(journal_t *journal, tid_t first_tid, tid_t tid, tid_t last_tid,
-		 unsigned long nr_freed, unsigned long nr_scanned,
-		 tid_t next_tid),
+		 unsigned long nr_freed, tid_t next_tid),
 
-	TP_ARGS(journal, first_tid, tid, last_tid, nr_freed,
-		nr_scanned, next_tid),
+	TP_ARGS(journal, first_tid, tid, last_tid, nr_freed, next_tid),
 
 	TP_STRUCT__entry(
 		__field(dev_t, dev)
@@ -474,7 +472,6 @@
 		__field(tid_t, tid)
 		__field(tid_t, last_tid)
 		__field(unsigned long, nr_freed)
-		__field(unsigned long, nr_scanned)
 		__field(tid_t, next_tid)
 	),
 
@@ -484,15 +481,14 @@
 		__entry->tid		= tid;
 		__entry->last_tid	= last_tid;
 		__entry->nr_freed	= nr_freed;
-		__entry->nr_scanned	= nr_scanned;
 		__entry->next_tid	= next_tid;
 	),
 
 	TP_printk("dev %d,%d shrink transaction %u-%u(%u) freed %lu "
-		  "scanned %lu next transaction %u",
+		  "next transaction %u",
 		  MAJOR(__entry->dev), MINOR(__entry->dev),
 		  __entry->first_tid, __entry->tid, __entry->last_tid,
-		  __entry->nr_freed, __entry->nr_scanned, __entry->next_tid)
+		  __entry->nr_freed, __entry->next_tid)
 );
 
 #endif /* _TRACE_JBD2_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/kmem.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/kmem.h
@@ -229,20 +229,23 @@
 
 DECLARE_EVENT_CLASS(mm_page,
 
-	TP_PROTO(struct page *page, unsigned int order, int migratetype),
+	TP_PROTO(struct page *page, unsigned int order, int migratetype,
+		 int percpu_refill),
 
-	TP_ARGS(page, order, migratetype),
+	TP_ARGS(page, order, migratetype, percpu_refill),
 
 	TP_STRUCT__entry(
 		__field(	unsigned long,	pfn		)
 		__field(	unsigned int,	order		)
 		__field(	int,		migratetype	)
+		__field(	int,		percpu_refill	)
 	),
 
 	TP_fast_assign(
 		__entry->pfn		= page ? page_to_pfn(page) : -1UL;
 		__entry->order		= order;
 		__entry->migratetype	= migratetype;
+		__entry->percpu_refill	= percpu_refill;
 	),
 
 	TP_printk("page=%p pfn=0x%lx order=%u migratetype=%d percpu_refill=%d",
@@ -250,14 +253,15 @@
 		__entry->pfn != -1UL ? __entry->pfn : 0,
 		__entry->order,
 		__entry->migratetype,
-		__entry->order == 0)
+		__entry->percpu_refill)
 );
 
 DEFINE_EVENT(mm_page, mm_page_alloc_zone_locked,
 
-	TP_PROTO(struct page *page, unsigned int order, int migratetype),
+	TP_PROTO(struct page *page, unsigned int order, int migratetype,
+		 int percpu_refill),
 
-	TP_ARGS(page, order, migratetype)
+	TP_ARGS(page, order, migratetype, percpu_refill)
 );
 
 TRACE_EVENT(mm_page_pcpu_drain,
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/libata.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/libata.h
@@ -249,6 +249,7 @@
 		__entry->hob_feature	= qc->result_tf.hob_feature;
 		__entry->nsect		= qc->result_tf.nsect;
 		__entry->hob_nsect	= qc->result_tf.hob_nsect;
+		__entry->flags		= qc->flags;
 	),
 
 	TP_printk("ata_port=%u ata_dev=%u tag=%d flags=%s status=%s " \
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/mptcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/mptcp.h
@@ -34,7 +34,7 @@
 		struct sock *ssk;
 
 		__entry->active = mptcp_subflow_active(subflow);
-		__entry->backup = subflow->backup;
+		__entry->backup = subflow->backup || subflow->request_bkup;
 
 		if (subflow->tcp_sock && sk_fullsock(subflow->tcp_sock))
 			__entry->free = sk_stream_memory_free(subflow->tcp_sock);
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/neigh.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/neigh.h
@@ -39,7 +39,6 @@
 	),
 
 	TP_fast_assign(
-		struct in6_addr *pin6;
 		__be32 *p32;
 
 		__entry->family = tbl->family;
@@ -47,7 +46,6 @@
 		__entry->entries = atomic_read(&tbl->gc_entries);
 		__entry->created = n != NULL;
 		__entry->gc_exempt = exempt_from_gc;
-		pin6 = (struct in6_addr *)__entry->primary_key6;
 		p32 = (__be32 *)__entry->primary_key4;
 
 		if (tbl->family == AF_INET)
@@ -57,6 +55,8 @@
 
 #if IS_ENABLED(CONFIG_IPV6)
 		if (tbl->family == AF_INET6) {
+			struct in6_addr *pin6;
+
 			pin6 = (struct in6_addr *)__entry->primary_key6;
 			*pin6 = *(struct in6_addr *)pkey;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/oom.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/oom.h
@@ -7,6 +7,8 @@
 #include <linux/tracepoint.h>
 #include <trace/events/mmflags.h>
 
+#define PG_COUNT_TO_KB(x) ((x) << (PAGE_SHIFT - 10))
+
 TRACE_EVENT(oom_score_adj_update,
 
 	TP_PROTO(struct task_struct *task),
@@ -72,19 +74,45 @@
 );
 
 TRACE_EVENT(mark_victim,
-	TP_PROTO(int pid),
+	TP_PROTO(struct task_struct *task, uid_t uid),
 
-	TP_ARGS(pid),
+	TP_ARGS(task, uid),
 
 	TP_STRUCT__entry(
 		__field(int, pid)
+		__string(comm, task->comm)
+		__field(unsigned long, total_vm)
+		__field(unsigned long, anon_rss)
+		__field(unsigned long, file_rss)
+		__field(unsigned long, shmem_rss)
+		__field(uid_t, uid)
+		__field(unsigned long, pgtables)
+		__field(short, oom_score_adj)
 	),
 
 	TP_fast_assign(
-		__entry->pid = pid;
+		__entry->pid = task->pid;
+		__assign_str(comm, task->comm);
+		__entry->total_vm = PG_COUNT_TO_KB(task->mm->total_vm);
+		__entry->anon_rss = PG_COUNT_TO_KB(get_mm_counter(task->mm, MM_ANONPAGES));
+		__entry->file_rss = PG_COUNT_TO_KB(get_mm_counter(task->mm, MM_FILEPAGES));
+		__entry->shmem_rss = PG_COUNT_TO_KB(get_mm_counter(task->mm, MM_SHMEMPAGES));
+		__entry->uid = uid;
+		__entry->pgtables = mm_pgtables_bytes(task->mm) >> 10;
+		__entry->oom_score_adj = task->signal->oom_score_adj;
 	),
 
-	TP_printk("pid=%d", __entry->pid)
+	TP_printk("pid=%d comm=%s total-vm=%lukB anon-rss=%lukB file-rss:%lukB shmem-rss:%lukB uid=%u pgtables=%lukB oom_score_adj=%hd",
+		__entry->pid,
+		__get_str(comm),
+		__entry->total_vm,
+		__entry->anon_rss,
+		__entry->file_rss,
+		__entry->shmem_rss,
+		__entry->uid,
+		__entry->pgtables,
+		__entry->oom_score_adj
+	)
 );
 
 TRACE_EVENT(wake_reaper,
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/qdisc.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/qdisc.h
@@ -81,14 +81,14 @@
 	TP_ARGS(q),
 
 	TP_STRUCT__entry(
-		__string(	dev,		qdisc_dev(q)	)
-		__string(	kind,		q->ops->id	)
-		__field(	u32,		parent		)
-		__field(	u32,		handle		)
+		__string(	dev,		qdisc_dev(q) ? qdisc_dev(q)->name : "(null)"	)
+		__string(	kind,		q->ops->id		)
+		__field(	u32,		parent			)
+		__field(	u32,		handle			)
 	),
 
 	TP_fast_assign(
-		__assign_str(dev, qdisc_dev(q));
+		__assign_str(dev, qdisc_dev(q) ? qdisc_dev(q)->name : "(null)");
 		__assign_str(kind, q->ops->id);
 		__entry->parent = q->parent;
 		__entry->handle = q->handle;
@@ -106,14 +106,14 @@
 	TP_ARGS(q),
 
 	TP_STRUCT__entry(
-		__string(	dev,		qdisc_dev(q)	)
-		__string(	kind,		q->ops->id	)
-		__field(	u32,		parent		)
-		__field(	u32,		handle		)
+		__string(	dev,		qdisc_dev(q)->name	)
+		__string(	kind,		q->ops->id		)
+		__field(	u32,		parent			)
+		__field(	u32,		handle			)
 	),
 
 	TP_fast_assign(
-		__assign_str(dev, qdisc_dev(q));
+		__assign_str(dev, qdisc_dev(q)->name);
 		__assign_str(kind, q->ops->id);
 		__entry->parent = q->parent;
 		__entry->handle = q->handle;
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/qrtr.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/qrtr.h
@@ -10,15 +10,16 @@
 
 TRACE_EVENT(qrtr_ns_service_announce_new,
 
-	TP_PROTO(__le32 service, __le32 instance, __le32 node, __le32 port),
+	TP_PROTO(unsigned int service, unsigned int instance,
+		 unsigned int node, unsigned int port),
 
 	TP_ARGS(service, instance, node, port),
 
 	TP_STRUCT__entry(
-		__field(__le32, service)
-		__field(__le32, instance)
-		__field(__le32, node)
-		__field(__le32, port)
+		__field(unsigned int, service)
+		__field(unsigned int, instance)
+		__field(unsigned int, node)
+		__field(unsigned int, port)
 	),
 
 	TP_fast_assign(
@@ -36,15 +37,16 @@
 
 TRACE_EVENT(qrtr_ns_service_announce_del,
 
-	TP_PROTO(__le32 service, __le32 instance, __le32 node, __le32 port),
+	TP_PROTO(unsigned int service, unsigned int instance,
+		 unsigned int node, unsigned int port),
 
 	TP_ARGS(service, instance, node, port),
 
 	TP_STRUCT__entry(
-		__field(__le32, service)
-		__field(__le32, instance)
-		__field(__le32, node)
-		__field(__le32, port)
+		__field(unsigned int, service)
+		__field(unsigned int, instance)
+		__field(unsigned int, node)
+		__field(unsigned int, port)
 	),
 
 	TP_fast_assign(
@@ -62,15 +64,16 @@
 
 TRACE_EVENT(qrtr_ns_server_add,
 
-	TP_PROTO(__le32 service, __le32 instance, __le32 node, __le32 port),
+	TP_PROTO(unsigned int service, unsigned int instance,
+		 unsigned int node, unsigned int port),
 
 	TP_ARGS(service, instance, node, port),
 
 	TP_STRUCT__entry(
-		__field(__le32, service)
-		__field(__le32, instance)
-		__field(__le32, node)
-		__field(__le32, port)
+		__field(unsigned int, service)
+		__field(unsigned int, instance)
+		__field(unsigned int, node)
+		__field(unsigned int, port)
 	),
 
 	TP_fast_assign(
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/rcu.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/rcu.h
@@ -768,7 +768,7 @@
 	TP_ARGS(rcutorturename, rhp, secs, c_old, c),
 
 	TP_STRUCT__entry(
-		__field(char, rcutorturename[RCUTORTURENAME_LEN])
+		__array(char, rcutorturename, RCUTORTURENAME_LEN)
 		__field(struct rcu_head *, rhp)
 		__field(unsigned long, secs)
 		__field(unsigned long, c_old)
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/rpcgss.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/rpcgss.h
@@ -13,6 +13,8 @@
 
 #include <linux/tracepoint.h>
 
+#include <trace/misc/sunrpc.h>
+
 /**
  ** GSS-API related trace events
  **/
@@ -52,7 +54,7 @@
 TRACE_DEFINE_ENUM(GSS_S_GAP_TOKEN);
 
 #define show_gss_status(x)						\
-	__print_flags(x, "|",						\
+	__print_symbolic(x, 						\
 		{ GSS_S_BAD_MECH, "GSS_S_BAD_MECH" },			\
 		{ GSS_S_BAD_NAME, "GSS_S_BAD_NAME" },			\
 		{ GSS_S_BAD_NAMETYPE, "GSS_S_BAD_NAMETYPE" },		\
@@ -99,7 +101,7 @@
 		__entry->maj_stat = maj_stat;
 	),
 
-	TP_printk("task:%u@%u maj_stat=%s",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " maj_stat=%s",
 		__entry->task_id, __entry->client_id,
 		__entry->maj_stat == 0 ?
 		"GSS_S_COMPLETE" : show_gss_status(__entry->maj_stat))
@@ -332,7 +334,8 @@
 		__entry->client_id = task->tk_client->cl_clid;
 	),
 
-	TP_printk("task:%u@%u", __entry->task_id, __entry->client_id)
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER,
+		__entry->task_id, __entry->client_id)
 );
 
 TRACE_EVENT(rpcgss_bad_seqno,
@@ -358,7 +361,8 @@
 		__entry->received = received;
 	),
 
-	TP_printk("task:%u@%u expected seqno %u, received seqno %u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " expected seqno %u, received seqno %u",
 		__entry->task_id, __entry->client_id,
 		__entry->expected, __entry->received)
 );
@@ -386,7 +390,7 @@
 		__entry->seqno = rqst->rq_seqno;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x seqno=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x seqno=%u",
 		__entry->task_id, __entry->client_id,
 		__entry->xid, __entry->seqno)
 );
@@ -418,7 +422,8 @@
 		__entry->ret = ret;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x rq_seqno=%u seq_xmit=%u reencode %sneeded",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " xid=0x%08x rq_seqno=%u seq_xmit=%u reencode %sneeded",
 		__entry->task_id, __entry->client_id,
 		__entry->xid, __entry->seqno, __entry->seq_xmit,
 		__entry->ret ? "" : "un")
@@ -452,7 +457,8 @@
 		__entry->verfsize = auth->au_verfsize;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x auth=%p rslack=%u ralign=%u verfsize=%u\n",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " xid=0x%08x auth=%p rslack=%u ralign=%u verfsize=%u\n",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->auth, __entry->rslack, __entry->ralign,
 		__entry->verfsize)
@@ -581,7 +587,7 @@
 		__field(unsigned int, timeout)
 		__field(u32, window_size)
 		__field(int, len)
-		__string(acceptor, data)
+		__string_len(acceptor, data, len)
 	),
 
 	TP_fast_assign(
@@ -590,7 +596,7 @@
 		__entry->timeout = timeout;
 		__entry->window_size = window_size;
 		__entry->len = len;
-		strncpy(__get_str(acceptor), data, len);
+		__assign_str(acceptor, data);
 	),
 
 	TP_printk("win_size=%u expiry=%lu now=%lu timeout=%u acceptor=%.*s",
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/rpcrdma.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/rpcrdma.h
@@ -14,7 +14,9 @@
 #include <linux/sunrpc/rpc_rdma_cid.h>
 #include <linux/tracepoint.h>
 #include <rdma/ib_cm.h>
-#include <trace/events/rdma.h>
+
+#include <trace/misc/rdma.h>
+#include <trace/misc/sunrpc.h>
 
 /**
  ** Event classes
@@ -279,7 +281,8 @@
 		__entry->nsegs = nsegs;
 	),
 
-	TP_printk("task:%u@%u pos=%u %u@0x%016llx:0x%08x (%s)",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " pos=%u %u@0x%016llx:0x%08x (%s)",
 		__entry->task_id, __entry->client_id,
 		__entry->pos, __entry->length,
 		(unsigned long long)__entry->offset, __entry->handle,
@@ -326,7 +329,8 @@
 		__entry->nsegs = nsegs;
 	),
 
-	TP_printk("task:%u@%u %u@0x%016llx:0x%08x (%s)",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " %u@0x%016llx:0x%08x (%s)",
 		__entry->task_id, __entry->client_id,
 		__entry->length, (unsigned long long)__entry->offset,
 		__entry->handle,
@@ -387,7 +391,8 @@
 		__entry->dir    = mr->mr_dir;
 	),
 
-	TP_printk("task:%u@%u mr.id=%u nents=%d %u@0x%016llx:0x%08x (%s)",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " mr.id=%u nents=%d %u@0x%016llx:0x%08x (%s)",
 		__entry->task_id, __entry->client_id,
 		__entry->mr_id, __entry->nents, __entry->length,
 		(unsigned long long)__entry->offset, __entry->handle,
@@ -630,9 +635,9 @@
 		__assign_str(port, rpcrdma_portstr(r_xprt));
 	),
 
-	TP_printk("peer=[%s]:%s task:%u@%u",
-		__get_str(addr), __get_str(port),
-		__entry->task_id, __entry->client_id
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " peer=[%s]:%s",
+		__entry->task_id, __entry->client_id,
+		__get_str(addr), __get_str(port)
 	)
 );
 
@@ -693,7 +698,8 @@
 		__entry->wtype = wtype;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x: hdr=%u xdr=%u/%u/%u %s/%s",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " xid=0x%08x hdr=%u xdr=%u/%u/%u %s/%s",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->hdrlen,
 		__entry->headlen, __entry->pagelen, __entry->taillen,
@@ -723,7 +729,7 @@
 		__entry->ret = ret;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x: ret=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x ret=%d",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->ret
 	)
@@ -750,7 +756,7 @@
 		__entry->ret = ret;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x: ret=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x ret=%d",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->ret
 	)
@@ -785,7 +791,7 @@
 		__entry->signaled = req->rl_wr.send_flags & IB_SEND_SIGNALED;
 	),
 
-	TP_printk("task:%u@%u cq.id=%u cid=%d (%d SGE%s) %s",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " cq.id=%u cid=%d (%d SGE%s) %s",
 		__entry->task_id, __entry->client_id,
 		__entry->cq_id, __entry->completion_id,
 		__entry->num_sge, (__entry->num_sge == 1 ? "" : "s"),
@@ -820,7 +826,7 @@
 		__entry->rc = rc;
 	),
 
-	TP_printk("task:%u@%u cq.id=%u rc=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " cq.id=%u rc=%d",
 		__entry->task_id, __entry->client_id,
 		__entry->cq_id, __entry->rc
 	)
@@ -932,7 +938,7 @@
 		__entry->status = status;
 	),
 
-	TP_printk("task:%u@%u status=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " status=%d",
 		__entry->task_id, __entry->client_id, __entry->status
 	)
 );
@@ -1120,7 +1126,7 @@
 		__entry->credits = credits;
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x credits=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x credits=%u",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->credits
 	)
@@ -1156,7 +1162,7 @@
 		__entry->max = be32_to_cpup(max);
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x versions=[%u, %u]",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x versions=[%u, %u]",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->min, __entry->max
 	)
@@ -1181,7 +1187,7 @@
 		__entry->xid = be32_to_cpu(rqst->rq_xid);
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x",
 		__entry->task_id, __entry->client_id, __entry->xid
 	)
 );
@@ -1207,7 +1213,7 @@
 		__entry->procedure = be32_to_cpup(procedure);
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x procedure=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x procedure=%u",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->procedure
 	)
@@ -1239,7 +1245,7 @@
 		__entry->taillen = rqst->rq_rcv_buf.tail[0].iov_len;
 	),
 
-	TP_printk("task:%u@%u fixup=%lu xdr=%zu/%u/%zu",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " fixup=%lu xdr=%zu/%u/%zu",
 		__entry->task_id, __entry->client_id, __entry->fixup,
 		__entry->headlen, __entry->pagelen, __entry->taillen
 	)
@@ -1289,7 +1295,7 @@
 		__entry->client_id = task->tk_client->cl_clid;
 	),
 
-	TP_printk("task:%u@%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER,
 		__entry->task_id, __entry->client_id
 	)
 );
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/rxrpc.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/rxrpc.h
@@ -83,12 +83,15 @@
 	rxrpc_call_error,
 	rxrpc_call_got,
 	rxrpc_call_got_kernel,
+	rxrpc_call_got_timer,
 	rxrpc_call_got_userid,
 	rxrpc_call_new_client,
 	rxrpc_call_new_service,
 	rxrpc_call_put,
 	rxrpc_call_put_kernel,
 	rxrpc_call_put_noqueue,
+	rxrpc_call_put_notimer,
+	rxrpc_call_put_timer,
 	rxrpc_call_put_userid,
 	rxrpc_call_queued,
 	rxrpc_call_queued_ref,
@@ -278,12 +281,15 @@
 	EM(rxrpc_call_error,			"*E*") \
 	EM(rxrpc_call_got,			"GOT") \
 	EM(rxrpc_call_got_kernel,		"Gke") \
+	EM(rxrpc_call_got_timer,		"GTM") \
 	EM(rxrpc_call_got_userid,		"Gus") \
 	EM(rxrpc_call_new_client,		"NWc") \
 	EM(rxrpc_call_new_service,		"NWs") \
 	EM(rxrpc_call_put,			"PUT") \
 	EM(rxrpc_call_put_kernel,		"Pke") \
-	EM(rxrpc_call_put_noqueue,		"PNQ") \
+	EM(rxrpc_call_put_noqueue,		"PnQ") \
+	EM(rxrpc_call_put_notimer,		"PnT") \
+	EM(rxrpc_call_put_timer,		"PTM") \
 	EM(rxrpc_call_put_userid,		"Pus") \
 	EM(rxrpc_call_queued,			"QUE") \
 	EM(rxrpc_call_queued_ref,		"QUR") \
@@ -577,7 +583,7 @@
 	    TP_fast_assign(
 		    __entry->conn = conn ? conn->debug_id : 0;
 		    __entry->channel = channel;
-		    __entry->usage = conn ? atomic_read(&conn->usage) : -2;
+		    __entry->usage = conn ? refcount_read(&conn->ref) : -2;
 		    __entry->op = op;
 		    __entry->cid = conn ? conn->proto.cid : 0;
 			   ),
@@ -1503,7 +1509,7 @@
 		    __entry->call_serial = call->rx_serial;
 		    __entry->conn_serial = call->conn->hi_serial;
 		    __entry->tx_seq = call->tx_hard_ack;
-		    __entry->rx_seq = call->ackr_seen;
+		    __entry->rx_seq = call->rx_hard_ack;
 			   ),
 
 	    TP_printk("c=%08x %08x:%08x r=%08x/%08x tx=%08x rx=%08x",
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/skb.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/skb.h
@@ -9,29 +9,63 @@
 #include <linux/netdevice.h>
 #include <linux/tracepoint.h>
 
+#define TRACE_SKB_DROP_REASON					\
+	EM(SKB_DROP_REASON_NOT_SPECIFIED, NOT_SPECIFIED)	\
+	EM(SKB_DROP_REASON_NO_SOCKET, NO_SOCKET)		\
+	EM(SKB_DROP_REASON_PKT_TOO_SMALL, PKT_TOO_SMALL)	\
+	EM(SKB_DROP_REASON_TCP_CSUM, TCP_CSUM)			\
+	EM(SKB_DROP_REASON_SOCKET_FILTER, SOCKET_FILTER)	\
+	EM(SKB_DROP_REASON_UDP_CSUM, UDP_CSUM)			\
+	EM(SKB_DROP_REASON_NETFILTER_DROP, NETFILTER_DROP)	\
+	EM(SKB_DROP_REASON_OTHERHOST, OTHERHOST)		\
+	EM(SKB_DROP_REASON_IP_CSUM, IP_CSUM)			\
+	EM(SKB_DROP_REASON_IP_INHDR, IP_INHDR)			\
+	EM(SKB_DROP_REASON_IP_RPFILTER, IP_RPFILTER)		\
+	EM(SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST,		\
+	   UNICAST_IN_L2_MULTICAST)				\
+	EMe(SKB_DROP_REASON_MAX, MAX)
+
+#undef EM
+#undef EMe
+
+#define EM(a, b)	TRACE_DEFINE_ENUM(a);
+#define EMe(a, b)	TRACE_DEFINE_ENUM(a);
+
+TRACE_SKB_DROP_REASON
+
+#undef EM
+#undef EMe
+#define EM(a, b)	{ a, #b },
+#define EMe(a, b)	{ a, #b }
+
 /*
  * Tracepoint for free an sk_buff:
  */
 TRACE_EVENT(kfree_skb,
 
-	TP_PROTO(struct sk_buff *skb, void *location),
+	TP_PROTO(struct sk_buff *skb, void *location,
+		 enum skb_drop_reason reason),
 
-	TP_ARGS(skb, location),
+	TP_ARGS(skb, location, reason),
 
 	TP_STRUCT__entry(
-		__field(	void *,		skbaddr		)
-		__field(	void *,		location	)
-		__field(	unsigned short,	protocol	)
+		__field(void *,		skbaddr)
+		__field(void *,		location)
+		__field(unsigned short,	protocol)
+		__field(enum skb_drop_reason,	reason)
 	),
 
 	TP_fast_assign(
 		__entry->skbaddr = skb;
 		__entry->location = location;
 		__entry->protocol = ntohs(skb->protocol);
+		__entry->reason = reason;
 	),
 
-	TP_printk("skbaddr=%p protocol=%u location=%p",
-		__entry->skbaddr, __entry->protocol, __entry->location)
+	TP_printk("skbaddr=%p protocol=%u location=%p reason: %s",
+		  __entry->skbaddr, __entry->protocol, __entry->location,
+		  __print_symbolic(__entry->reason,
+				   TRACE_SKB_DROP_REASON))
 );
 
 TRACE_EVENT(consume_skb,
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/sock.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/sock.h
@@ -98,7 +98,7 @@
 
 	TP_STRUCT__entry(
 		__array(char, name, 32)
-		__field(long *, sysctl_mem)
+		__array(long, sysctl_mem, 3)
 		__field(long, allocated)
 		__field(int, sysctl_rmem)
 		__field(int, rmem_alloc)
@@ -110,7 +110,9 @@
 
 	TP_fast_assign(
 		strncpy(__entry->name, prot->name, 32);
-		__entry->sysctl_mem = prot->sysctl_mem;
+		__entry->sysctl_mem[0] = READ_ONCE(prot->sysctl_mem[0]);
+		__entry->sysctl_mem[1] = READ_ONCE(prot->sysctl_mem[1]);
+		__entry->sysctl_mem[2] = READ_ONCE(prot->sysctl_mem[2]);
 		__entry->allocated = allocated;
 		__entry->sysctl_rmem = sk_get_rmem0(sk, prot);
 		__entry->rmem_alloc = atomic_read(&sk->sk_rmem_alloc);
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/spmi.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/spmi.h
@@ -21,15 +21,15 @@
 		__field		( u8,         sid       )
 		__field		( u16,        addr      )
 		__field		( u8,         len       )
-		__dynamic_array	( u8,   buf,  len + 1   )
+		__dynamic_array	( u8,   buf,  len       )
 	),
 
 	TP_fast_assign(
 		__entry->opcode = opcode;
 		__entry->sid    = sid;
 		__entry->addr   = addr;
-		__entry->len    = len + 1;
-		memcpy(__get_dynamic_array(buf), buf, len + 1);
+		__entry->len    = len;
+		memcpy(__get_dynamic_array(buf), buf, len);
 	),
 
 	TP_printk("opc=%d sid=%02d addr=0x%04x len=%d buf=0x[%*phD]",
@@ -92,7 +92,7 @@
 		__field		( u16,        addr      )
 		__field		( int,        ret       )
 		__field		( u8,         len       )
-		__dynamic_array	( u8,   buf,  len + 1   )
+		__dynamic_array	( u8,   buf,  len       )
 	),
 
 	TP_fast_assign(
@@ -100,8 +100,8 @@
 		__entry->sid    = sid;
 		__entry->addr   = addr;
 		__entry->ret    = ret;
-		__entry->len    = len + 1;
-		memcpy(__get_dynamic_array(buf), buf, len + 1);
+		__entry->len    = len;
+		memcpy(__get_dynamic_array(buf), buf, len);
 	),
 
 	TP_printk("opc=%d sid=%02d addr=0x%04x ret=%d len=%02d buf=0x[%*phD]",
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/sunrpc.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/sunrpc.h
@@ -14,6 +14,8 @@
 #include <linux/net.h>
 #include <linux/tracepoint.h>
 
+#include <trace/misc/sunrpc.h>
+
 TRACE_DEFINE_ENUM(SOCK_STREAM);
 TRACE_DEFINE_ENUM(SOCK_DGRAM);
 TRACE_DEFINE_ENUM(SOCK_RAW);
@@ -78,7 +80,8 @@
 		__entry->msg_len = xdr->len;
 	),
 
-	TP_printk("task:%u@%u head=[%p,%zu] page=%u tail=[%p,%zu] len=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " head=[%p,%zu] page=%u tail=[%p,%zu] len=%u",
 		__entry->task_id, __entry->client_id,
 		__entry->head_base, __entry->head_len, __entry->page_len,
 		__entry->tail_base, __entry->tail_len, __entry->msg_len
@@ -114,7 +117,7 @@
 		__entry->client_id = clnt->cl_clid;
 	),
 
-	TP_printk("clid=%u", __entry->client_id)
+	TP_printk("client=" SUNRPC_TRACE_CLID_SPECIFIER, __entry->client_id)
 );
 
 #define DEFINE_RPC_CLNT_EVENT(name)					\
@@ -158,7 +161,8 @@
 		__assign_str(server, server);
 	),
 
-	TP_printk("client=%u peer=[%s]:%s program=%s server=%s",
+	TP_printk("client=" SUNRPC_TRACE_CLID_SPECIFIER
+		  " peer=[%s]:%s program=%s server=%s",
 		__entry->client_id, __get_str(addr), __get_str(port),
 		__get_str(program), __get_str(server))
 );
@@ -206,7 +210,8 @@
 		__entry->error = error;
 	),
 
-	TP_printk("client=%u error=%d", __entry->client_id, __entry->error)
+	TP_printk("client=" SUNRPC_TRACE_CLID_SPECIFIER " error=%d",
+		__entry->client_id, __entry->error)
 );
 
 
@@ -248,7 +253,7 @@
 		__entry->status = task->tk_status;
 	),
 
-	TP_printk("task:%u@%u status=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " status=%d",
 		__entry->task_id, __entry->client_id,
 		__entry->status)
 );
@@ -288,7 +293,7 @@
 		__assign_str(procname, rpc_proc_name(task));
 	),
 
-	TP_printk("task:%u@%u %sv%d %s (%ssync)",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " %sv%d %s (%ssync)",
 		__entry->task_id, __entry->client_id,
 		__get_str(progname), __entry->version,
 		__get_str(procname), __entry->async ? "a": ""
@@ -348,7 +353,8 @@
 		__entry->flags = task->tk_flags;
 		),
 
-	TP_printk("task:%u@%d flags=%s runstate=%s status=%d action=%ps",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " flags=%s runstate=%s status=%d action=%ps",
 		__entry->task_id, __entry->client_id,
 		rpc_show_task_flags(__entry->flags),
 		rpc_show_runstate(__entry->runstate),
@@ -400,7 +406,8 @@
 		__assign_str(q_name, rpc_qname(q));
 		),
 
-	TP_printk("task:%u@%d flags=%s runstate=%s status=%d timeout=%lu queue=%s",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " flags=%s runstate=%s status=%d timeout=%lu queue=%s",
 		__entry->task_id, __entry->client_id,
 		rpc_show_task_flags(__entry->flags),
 		rpc_show_runstate(__entry->runstate),
@@ -436,7 +443,7 @@
 		__entry->client_id = task->tk_client->cl_clid;
 	),
 
-	TP_printk("task:%u@%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER,
 		__entry->task_id, __entry->client_id)
 );
 
@@ -478,7 +485,8 @@
 		__assign_str(servername, task->tk_xprt->servername);
 	),
 
-	TP_printk("task:%u@%d server=%s xid=0x%08x %sv%d %s",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " server=%s xid=0x%08x %sv%d %s",
 		__entry->task_id, __entry->client_id, __get_str(servername),
 		__entry->xid, __get_str(progname), __entry->version,
 		__get_str(procname))
@@ -538,7 +546,8 @@
 		__entry->status = status;
 	),
 
-	TP_printk("task:%u@%u callsize=%zu recvsize=%zu status=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " callsize=%zu recvsize=%zu status=%d",
 		__entry->task_id, __entry->client_id,
 		__entry->callsize, __entry->recvsize, __entry->status
 	)
@@ -567,7 +576,8 @@
 		__entry->rpc_status = rpc_status;
 	),
 
-	TP_printk("task:%u@%u tk_status=%d rpc_status=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " tk_status=%d rpc_status=%d",
 		__entry->task_id, __entry->client_id,
 		__entry->tk_status, __entry->rpc_status)
 );
@@ -607,7 +617,8 @@
 		__entry->execute = ktime_to_us(execute);
 	),
 
-	TP_printk("task:%u@%d xid=0x%08x %sv%d %s backlog=%lu rtt=%lu execute=%lu",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " xid=0x%08x %sv%d %s backlog=%lu rtt=%lu execute=%lu",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__get_str(progname), __entry->version, __get_str(procname),
 		__entry->backlog, __entry->rtt, __entry->execute)
@@ -651,8 +662,8 @@
 			__entry->version = task->tk_client->cl_vers;
 			__assign_str(procedure, task->tk_msg.rpc_proc->p_name);
 		} else {
-			__entry->task_id = 0;
-			__entry->client_id = 0;
+			__entry->task_id = -1;
+			__entry->client_id = -1;
 			__assign_str(progname, "unknown");
 			__entry->version = 0;
 			__assign_str(procedure, "unknown");
@@ -668,8 +679,8 @@
 		__entry->len = xdr->buf->len;
 	),
 
-	TP_printk(
-		"task:%u@%u %sv%d %s requested=%zu p=%p end=%p xdr=[%p,%zu]/%u/[%p,%zu]/%u\n",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " %sv%d %s requested=%zu p=%p end=%p xdr=[%p,%zu]/%u/[%p,%zu]/%u\n",
 		__entry->task_id, __entry->client_id,
 		__get_str(progname), __entry->version, __get_str(procedure),
 		__entry->requested, __entry->p, __entry->end,
@@ -727,8 +738,8 @@
 		__entry->len = xdr->buf->len;
 	),
 
-	TP_printk(
-		"task:%u@%u %sv%d %s offset=%zu copied=%u xdr=[%p,%zu]/%u/[%p,%zu]/%u\n",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " %sv%d %s offset=%zu copied=%u xdr=[%p,%zu]/%u/[%p,%zu]/%u\n",
 		__entry->task_id, __entry->client_id,
 		__get_str(progname), __entry->version, __get_str(procedure),
 		__entry->offset, __entry->copied,
@@ -917,7 +928,8 @@
 		__entry->remaining = rqst->rq_slen - transport->xmit.offset;
 	),
 
-	TP_printk("task:%u@%u total=%u remaining=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " total=%u remaining=%u",
 		__entry->task_id, __entry->client_id,
 		__entry->total, __entry->remaining
 	)
@@ -925,18 +937,19 @@
 
 #define rpc_show_xprt_state(x)						\
 	__print_flags(x, "|",						\
-		{ (1UL << XPRT_LOCKED),		"LOCKED"},		\
-		{ (1UL << XPRT_CONNECTED),	"CONNECTED"},		\
-		{ (1UL << XPRT_CONNECTING),	"CONNECTING"},		\
-		{ (1UL << XPRT_CLOSE_WAIT),	"CLOSE_WAIT"},		\
-		{ (1UL << XPRT_BOUND),		"BOUND"},		\
-		{ (1UL << XPRT_BINDING),	"BINDING"},		\
-		{ (1UL << XPRT_CLOSING),	"CLOSING"},		\
-		{ (1UL << XPRT_OFFLINE),	"OFFLINE"},		\
-		{ (1UL << XPRT_REMOVE),		"REMOVE"},		\
-		{ (1UL << XPRT_CONGESTED),	"CONGESTED"},		\
-		{ (1UL << XPRT_CWND_WAIT),	"CWND_WAIT"},		\
-		{ (1UL << XPRT_WRITE_SPACE),	"WRITE_SPACE"})
+		{ BIT(XPRT_LOCKED),		"LOCKED" },		\
+		{ BIT(XPRT_CONNECTED),		"CONNECTED" },		\
+		{ BIT(XPRT_CONNECTING),		"CONNECTING" },		\
+		{ BIT(XPRT_CLOSE_WAIT),		"CLOSE_WAIT" },		\
+		{ BIT(XPRT_BOUND),		"BOUND" },		\
+		{ BIT(XPRT_BINDING),		"BINDING" },		\
+		{ BIT(XPRT_CLOSING),		"CLOSING" },		\
+		{ BIT(XPRT_OFFLINE),		"OFFLINE" },		\
+		{ BIT(XPRT_REMOVE),		"REMOVE" },		\
+		{ BIT(XPRT_CONGESTED),		"CONGESTED" },		\
+		{ BIT(XPRT_CWND_WAIT),		"CWND_WAIT" },		\
+		{ BIT(XPRT_WRITE_SPACE),	"WRITE_SPACE" },	\
+		{ BIT(XPRT_SND_IS_COOKIE),	"SND_IS_COOKIE" })
 
 DECLARE_EVENT_CLASS(rpc_xprt_lifetime_class,
 	TP_PROTO(
@@ -975,7 +988,6 @@
 DEFINE_RPC_XPRT_LIFETIME_EVENT(disconnect_auto);
 DEFINE_RPC_XPRT_LIFETIME_EVENT(disconnect_done);
 DEFINE_RPC_XPRT_LIFETIME_EVENT(disconnect_force);
-DEFINE_RPC_XPRT_LIFETIME_EVENT(disconnect_cleanup);
 DEFINE_RPC_XPRT_LIFETIME_EVENT(destroy);
 
 DECLARE_EVENT_CLASS(rpc_xprt_event,
@@ -1042,8 +1054,8 @@
 		__entry->status = status;
 	),
 
-	TP_printk(
-		"task:%u@%u xid=0x%08x seqno=%u status=%d",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " xid=0x%08x seqno=%u status=%d",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__entry->seqno, __entry->status)
 );
@@ -1082,8 +1094,8 @@
 		__assign_str(procname, rpc_proc_name(task));
 	),
 
-	TP_printk(
-		"task:%u@%u xid=0x%08x %sv%d %s ntrans=%d timeout=%lu",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " xid=0x%08x %sv%d %s ntrans=%d timeout=%lu",
 		__entry->task_id, __entry->client_id, __entry->xid,
 		__get_str(progname), __entry->version, __get_str(procname),
 		__entry->ntrans, __entry->timeout
@@ -1133,11 +1145,15 @@
 			__entry->task_id = -1;
 			__entry->client_id = -1;
 		}
-		__entry->snd_task_id = xprt->snd_task ?
-					xprt->snd_task->tk_pid : -1;
+		if (xprt->snd_task &&
+		    !test_bit(XPRT_SND_IS_COOKIE, &xprt->state))
+			__entry->snd_task_id = xprt->snd_task->tk_pid;
+		else
+			__entry->snd_task_id = -1;
 	),
 
-	TP_printk("task:%u@%u snd_task:%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " snd_task:" SUNRPC_TRACE_PID_SPECIFIER,
 			__entry->task_id, __entry->client_id,
 			__entry->snd_task_id)
 );
@@ -1178,14 +1194,20 @@
 			__entry->task_id = -1;
 			__entry->client_id = -1;
 		}
-		__entry->snd_task_id = xprt->snd_task ?
-					xprt->snd_task->tk_pid : -1;
+		if (xprt->snd_task &&
+		    !test_bit(XPRT_SND_IS_COOKIE, &xprt->state))
+			__entry->snd_task_id = xprt->snd_task->tk_pid;
+		else
+			__entry->snd_task_id = -1;
+
 		__entry->cong = xprt->cong;
 		__entry->cwnd = xprt->cwnd;
 		__entry->wait = test_bit(XPRT_CWND_WAIT, &xprt->state);
 	),
 
-	TP_printk("task:%u@%u snd_task:%u cong=%lu cwnd=%lu%s",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " snd_task:" SUNRPC_TRACE_PID_SPECIFIER
+		  " cong=%lu cwnd=%lu%s",
 			__entry->task_id, __entry->client_id,
 			__entry->snd_task_id, __entry->cong, __entry->cwnd,
 			__entry->wait ? " (wait)" : "")
@@ -1223,7 +1245,7 @@
 		__entry->xid = be32_to_cpu(rqst->rq_xid);
 	),
 
-	TP_printk("task:%u@%u xid=0x%08x",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " xid=0x%08x",
 		__entry->task_id, __entry->client_id, __entry->xid
 	)
 );
@@ -1312,7 +1334,8 @@
 		__assign_str(servername, task->tk_xprt->servername);
 	),
 
-	TP_printk("task:%u@%u server=%s program=%u version=%u protocol=%d bind_version=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER
+		  " server=%s program=%u version=%u protocol=%d bind_version=%u",
 		__entry->task_id, __entry->client_id, __get_str(servername),
 		__entry->program, __entry->version, __entry->protocol,
 		__entry->bind_version
@@ -1342,7 +1365,7 @@
 		__entry->port = port;
 	),
 
-	TP_printk("task:%u@%u status=%d port=%u",
+	TP_printk(SUNRPC_TRACE_TASK_SPECIFIER " status=%d port=%u",
 		__entry->task_id, __entry->client_id,
 		__entry->status, __entry->port
 	)
@@ -1719,10 +1742,11 @@
 		const char *program,
 		const char *protocol,
 		struct sockaddr *sap,
+		size_t salen,
 		const struct svc_xprt *xprt
 	),
 
-	TP_ARGS(program, protocol, sap, xprt),
+	TP_ARGS(program, protocol, sap, salen, xprt),
 
 	TP_STRUCT__entry(
 		__field(long, error)
@@ -1735,7 +1759,7 @@
 		__entry->error = PTR_ERR(xprt);
 		__assign_str(program, program);
 		__assign_str(protocol, protocol);
-		memcpy(__entry->addr, sap, sizeof(__entry->addr));
+		memcpy(__entry->addr, sap, min(salen, sizeof(__entry->addr)));
 	),
 
 	TP_printk("addr=%pISpc program=%s protocol=%s error=%ld",
@@ -1915,18 +1939,17 @@
 	TP_STRUCT__entry(
 		__field(const void *, dr)
 		__field(u32, xid)
-		__string(addr, dr->xprt->xpt_remotebuf)
+		__sockaddr(addr, dr->addrlen)
 	),
 
 	TP_fast_assign(
 		__entry->dr = dr;
-		__entry->xid = be32_to_cpu(*(__be32 *)(dr->args +
-						       (dr->xprt_hlen>>2)));
-		__assign_str(addr, dr->xprt->xpt_remotebuf);
+		__entry->xid = be32_to_cpu(*(__be32 *)dr->args);
+		__assign_sockaddr(addr, &dr->addr, dr->addrlen);
 	),
 
-	TP_printk("addr=%s dr=%p xid=0x%08x", __get_str(addr), __entry->dr,
-		__entry->xid)
+	TP_printk("addr=%pISpc dr=%p xid=0x%08x", __get_sockaddr(addr),
+		__entry->dr, __entry->xid)
 );
 
 #define DEFINE_SVC_DEFERRED_EVENT(name) \
@@ -2103,17 +2126,17 @@
 	TP_STRUCT__entry(
 		__field(long, status)
 		__string(service, service)
-		__array(unsigned char, addr, sizeof(struct sockaddr_in6))
+		__field(unsigned int, netns_ino)
 	),
 
 	TP_fast_assign(
 		__entry->status = status;
 		__assign_str(service, service);
-		memcpy(__entry->addr, &xprt->xpt_local, sizeof(__entry->addr));
+		__entry->netns_ino = xprt->xpt_net->ns.inum;
 	),
 
-	TP_printk("listener=%pISpc service=%s status=%ld",
-		__entry->addr, __get_str(service), __entry->status
+	TP_printk("addr=listener service=%s status=%ld",
+		__get_str(service), __entry->status
 	)
 );
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/tcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/tcp.h
@@ -279,7 +279,7 @@
 		__entry->data_len = skb->len - __tcp_hdrlen(th);
 		__entry->snd_nxt = tp->snd_nxt;
 		__entry->snd_una = tp->snd_una;
-		__entry->snd_cwnd = tp->snd_cwnd;
+		__entry->snd_cwnd = tcp_snd_cwnd(tp);
 		__entry->snd_wnd = tp->snd_wnd;
 		__entry->rcv_wnd = tp->rcv_wnd;
 		__entry->ssthresh = tcp_current_ssthresh(sk);
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/timer.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/timer.h
@@ -156,7 +156,11 @@
 		{ HRTIMER_MODE_ABS_SOFT,	"ABS|SOFT"	},	\
 		{ HRTIMER_MODE_REL_SOFT,	"REL|SOFT"	},	\
 		{ HRTIMER_MODE_ABS_PINNED_SOFT,	"ABS|PINNED|SOFT" },	\
-		{ HRTIMER_MODE_REL_PINNED_SOFT,	"REL|PINNED|SOFT" })
+		{ HRTIMER_MODE_REL_PINNED_SOFT,	"REL|PINNED|SOFT" },	\
+		{ HRTIMER_MODE_ABS_HARD,	"ABS|HARD" },		\
+		{ HRTIMER_MODE_REL_HARD,	"REL|HARD" },		\
+		{ HRTIMER_MODE_ABS_PINNED_HARD, "ABS|PINNED|HARD" },	\
+		{ HRTIMER_MODE_REL_PINNED_HARD,	"REL|PINNED|HARD" })
 
 /**
  * hrtimer_init - called when the hrtimer is initialized
@@ -368,7 +372,8 @@
 		tick_dep_name(PERF_EVENTS)		\
 		tick_dep_name(SCHED)			\
 		tick_dep_name(CLOCK_UNSTABLE)		\
-		tick_dep_name_end(RCU)
+		tick_dep_name(RCU)			\
+		tick_dep_name_end(RCU_EXP)
 
 #undef tick_dep_name
 #undef tick_dep_mask_name
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/vmscan.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/vmscan.h
@@ -283,7 +283,7 @@
 		__field(unsigned long, nr_scanned)
 		__field(unsigned long, nr_skipped)
 		__field(unsigned long, nr_taken)
-		__field(isolate_mode_t, isolate_mode)
+		__field(unsigned int, isolate_mode)
 		__field(int, lru)
 	),
 
@@ -294,7 +294,7 @@
 		__entry->nr_scanned = nr_scanned;
 		__entry->nr_skipped = nr_skipped;
 		__entry->nr_taken = nr_taken;
-		__entry->isolate_mode = isolate_mode;
+		__entry->isolate_mode = (__force unsigned int)isolate_mode;
 		__entry->lru = lru;
 	),
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/events/writeback.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/events/writeback.h
@@ -68,7 +68,7 @@
 		strscpy_pad(__entry->name,
 			    bdi_dev_name(mapping ? inode_to_bdi(mapping->host) :
 					 NULL), 32);
-		__entry->ino = mapping ? mapping->host->i_ino : 0;
+		__entry->ino = (mapping && mapping->host) ? mapping->host->i_ino : 0;
 		__entry->index = page->index;
 	),
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/misc/fs.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/misc/fs.h
@@ -0,0 +1,122 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Display helpers for generic filesystem items
+ *
+ * Author: Chuck Lever <chuck.lever@oracle.com>
+ *
+ * Copyright (c) 2020, Oracle and/or its affiliates.
+ */
+
+#include <linux/fs.h>
+
+#define show_fs_dirent_type(x) \
+	__print_symbolic(x, \
+		{ DT_UNKNOWN,		"UNKNOWN" }, \
+		{ DT_FIFO,		"FIFO" }, \
+		{ DT_CHR,		"CHR" }, \
+		{ DT_DIR,		"DIR" }, \
+		{ DT_BLK,		"BLK" }, \
+		{ DT_REG,		"REG" }, \
+		{ DT_LNK,		"LNK" }, \
+		{ DT_SOCK,		"SOCK" }, \
+		{ DT_WHT,		"WHT" })
+
+#define show_fs_fcntl_open_flags(x) \
+	__print_flags(x, "|", \
+		{ O_WRONLY,		"O_WRONLY" }, \
+		{ O_RDWR,		"O_RDWR" }, \
+		{ O_CREAT,		"O_CREAT" }, \
+		{ O_EXCL,		"O_EXCL" }, \
+		{ O_NOCTTY,		"O_NOCTTY" }, \
+		{ O_TRUNC,		"O_TRUNC" }, \
+		{ O_APPEND,		"O_APPEND" }, \
+		{ O_NONBLOCK,		"O_NONBLOCK" }, \
+		{ O_DSYNC,		"O_DSYNC" }, \
+		{ O_DIRECT,		"O_DIRECT" }, \
+		{ O_LARGEFILE,		"O_LARGEFILE" }, \
+		{ O_DIRECTORY,		"O_DIRECTORY" }, \
+		{ O_NOFOLLOW,		"O_NOFOLLOW" }, \
+		{ O_NOATIME,		"O_NOATIME" }, \
+		{ O_CLOEXEC,		"O_CLOEXEC" })
+
+#define __fmode_flag(x)	{ (__force unsigned long)FMODE_##x, #x }
+#define show_fs_fmode_flags(x) \
+	__print_flags(x, "|", \
+		__fmode_flag(READ), \
+		__fmode_flag(WRITE), \
+		__fmode_flag(EXEC))
+
+#ifdef CONFIG_64BIT
+#define show_fs_fcntl_cmd(x) \
+	__print_symbolic(x, \
+		{ F_DUPFD,		"DUPFD" }, \
+		{ F_GETFD,		"GETFD" }, \
+		{ F_SETFD,		"SETFD" }, \
+		{ F_GETFL,		"GETFL" }, \
+		{ F_SETFL,		"SETFL" }, \
+		{ F_GETLK,		"GETLK" }, \
+		{ F_SETLK,		"SETLK" }, \
+		{ F_SETLKW,		"SETLKW" }, \
+		{ F_SETOWN,		"SETOWN" }, \
+		{ F_GETOWN,		"GETOWN" }, \
+		{ F_SETSIG,		"SETSIG" }, \
+		{ F_GETSIG,		"GETSIG" }, \
+		{ F_SETOWN_EX,		"SETOWN_EX" }, \
+		{ F_GETOWN_EX,		"GETOWN_EX" }, \
+		{ F_GETOWNER_UIDS,	"GETOWNER_UIDS" }, \
+		{ F_OFD_GETLK,		"OFD_GETLK" }, \
+		{ F_OFD_SETLK,		"OFD_SETLK" }, \
+		{ F_OFD_SETLKW,		"OFD_SETLKW" })
+#else /* CONFIG_64BIT */
+#define show_fs_fcntl_cmd(x) \
+	__print_symbolic(x, \
+		{ F_DUPFD,		"DUPFD" }, \
+		{ F_GETFD,		"GETFD" }, \
+		{ F_SETFD,		"SETFD" }, \
+		{ F_GETFL,		"GETFL" }, \
+		{ F_SETFL,		"SETFL" }, \
+		{ F_GETLK,		"GETLK" }, \
+		{ F_SETLK,		"SETLK" }, \
+		{ F_SETLKW,		"SETLKW" }, \
+		{ F_SETOWN,		"SETOWN" }, \
+		{ F_GETOWN,		"GETOWN" }, \
+		{ F_SETSIG,		"SETSIG" }, \
+		{ F_GETSIG,		"GETSIG" }, \
+		{ F_GETLK64,		"GETLK64" }, \
+		{ F_SETLK64,		"SETLK64" }, \
+		{ F_SETLKW64,		"SETLKW64" }, \
+		{ F_SETOWN_EX,		"SETOWN_EX" }, \
+		{ F_GETOWN_EX,		"GETOWN_EX" }, \
+		{ F_GETOWNER_UIDS,	"GETOWNER_UIDS" }, \
+		{ F_OFD_GETLK,		"OFD_GETLK" }, \
+		{ F_OFD_SETLK,		"OFD_SETLK" }, \
+		{ F_OFD_SETLKW,		"OFD_SETLKW" })
+#endif /* CONFIG_64BIT */
+
+#define show_fs_fcntl_lock_type(x) \
+	__print_symbolic(x, \
+		{ F_RDLCK,		"RDLCK" }, \
+		{ F_WRLCK,		"WRLCK" }, \
+		{ F_UNLCK,		"UNLCK" })
+
+#define show_fs_lookup_flags(flags) \
+	__print_flags(flags, "|", \
+		{ LOOKUP_FOLLOW,	"FOLLOW" }, \
+		{ LOOKUP_DIRECTORY,	"DIRECTORY" }, \
+		{ LOOKUP_AUTOMOUNT,	"AUTOMOUNT" }, \
+		{ LOOKUP_EMPTY,		"EMPTY" }, \
+		{ LOOKUP_DOWN,		"DOWN" }, \
+		{ LOOKUP_MOUNTPOINT,	"MOUNTPOINT" }, \
+		{ LOOKUP_REVAL,		"REVAL" }, \
+		{ LOOKUP_RCU,		"RCU" }, \
+		{ LOOKUP_OPEN,		"OPEN" }, \
+		{ LOOKUP_CREATE,	"CREATE" }, \
+		{ LOOKUP_EXCL,		"EXCL" }, \
+		{ LOOKUP_RENAME_TARGET,	"RENAME_TARGET" }, \
+		{ LOOKUP_PARENT,	"PARENT" }, \
+		{ LOOKUP_NO_SYMLINKS,	"NO_SYMLINKS" }, \
+		{ LOOKUP_NO_MAGICLINKS,	"NO_MAGICLINKS" }, \
+		{ LOOKUP_NO_XDEV,	"NO_XDEV" }, \
+		{ LOOKUP_BENEATH,	"BENEATH" }, \
+		{ LOOKUP_IN_ROOT,	"IN_ROOT" }, \
+		{ LOOKUP_CACHED,	"CACHED" })
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/misc/nfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/misc/nfs.h
@@ -0,0 +1,387 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Display helpers for NFS protocol elements
+ *
+ * Author: Chuck Lever <chuck.lever@oracle.com>
+ *
+ * Copyright (c) 2020, Oracle and/or its affiliates.
+ */
+
+#include <linux/nfs.h>
+#include <linux/nfs4.h>
+#include <uapi/linux/nfs.h>
+
+TRACE_DEFINE_ENUM(NFS_OK);
+TRACE_DEFINE_ENUM(NFSERR_PERM);
+TRACE_DEFINE_ENUM(NFSERR_NOENT);
+TRACE_DEFINE_ENUM(NFSERR_IO);
+TRACE_DEFINE_ENUM(NFSERR_NXIO);
+TRACE_DEFINE_ENUM(NFSERR_EAGAIN);
+TRACE_DEFINE_ENUM(NFSERR_ACCES);
+TRACE_DEFINE_ENUM(NFSERR_EXIST);
+TRACE_DEFINE_ENUM(NFSERR_XDEV);
+TRACE_DEFINE_ENUM(NFSERR_NODEV);
+TRACE_DEFINE_ENUM(NFSERR_NOTDIR);
+TRACE_DEFINE_ENUM(NFSERR_ISDIR);
+TRACE_DEFINE_ENUM(NFSERR_INVAL);
+TRACE_DEFINE_ENUM(NFSERR_FBIG);
+TRACE_DEFINE_ENUM(NFSERR_NOSPC);
+TRACE_DEFINE_ENUM(NFSERR_ROFS);
+TRACE_DEFINE_ENUM(NFSERR_MLINK);
+TRACE_DEFINE_ENUM(NFSERR_OPNOTSUPP);
+TRACE_DEFINE_ENUM(NFSERR_NAMETOOLONG);
+TRACE_DEFINE_ENUM(NFSERR_NOTEMPTY);
+TRACE_DEFINE_ENUM(NFSERR_DQUOT);
+TRACE_DEFINE_ENUM(NFSERR_STALE);
+TRACE_DEFINE_ENUM(NFSERR_REMOTE);
+TRACE_DEFINE_ENUM(NFSERR_WFLUSH);
+TRACE_DEFINE_ENUM(NFSERR_BADHANDLE);
+TRACE_DEFINE_ENUM(NFSERR_NOT_SYNC);
+TRACE_DEFINE_ENUM(NFSERR_BAD_COOKIE);
+TRACE_DEFINE_ENUM(NFSERR_NOTSUPP);
+TRACE_DEFINE_ENUM(NFSERR_TOOSMALL);
+TRACE_DEFINE_ENUM(NFSERR_SERVERFAULT);
+TRACE_DEFINE_ENUM(NFSERR_BADTYPE);
+TRACE_DEFINE_ENUM(NFSERR_JUKEBOX);
+
+#define show_nfs_status(x) \
+	__print_symbolic(x, \
+		{ NFS_OK,			"OK" }, \
+		{ NFSERR_PERM,			"PERM" }, \
+		{ NFSERR_NOENT,			"NOENT" }, \
+		{ NFSERR_IO,			"IO" }, \
+		{ NFSERR_NXIO,			"NXIO" }, \
+		{ ECHILD,			"CHILD" }, \
+		{ NFSERR_EAGAIN,		"AGAIN" }, \
+		{ NFSERR_ACCES,			"ACCES" }, \
+		{ NFSERR_EXIST,			"EXIST" }, \
+		{ NFSERR_XDEV,			"XDEV" }, \
+		{ NFSERR_NODEV,			"NODEV" }, \
+		{ NFSERR_NOTDIR,		"NOTDIR" }, \
+		{ NFSERR_ISDIR,			"ISDIR" }, \
+		{ NFSERR_INVAL,			"INVAL" }, \
+		{ NFSERR_FBIG,			"FBIG" }, \
+		{ NFSERR_NOSPC,			"NOSPC" }, \
+		{ NFSERR_ROFS,			"ROFS" }, \
+		{ NFSERR_MLINK,			"MLINK" }, \
+		{ NFSERR_OPNOTSUPP,		"OPNOTSUPP" }, \
+		{ NFSERR_NAMETOOLONG,		"NAMETOOLONG" }, \
+		{ NFSERR_NOTEMPTY,		"NOTEMPTY" }, \
+		{ NFSERR_DQUOT,			"DQUOT" }, \
+		{ NFSERR_STALE,			"STALE" }, \
+		{ NFSERR_REMOTE,		"REMOTE" }, \
+		{ NFSERR_WFLUSH,		"WFLUSH" }, \
+		{ NFSERR_BADHANDLE,		"BADHANDLE" }, \
+		{ NFSERR_NOT_SYNC,		"NOTSYNC" }, \
+		{ NFSERR_BAD_COOKIE,		"BADCOOKIE" }, \
+		{ NFSERR_NOTSUPP,		"NOTSUPP" }, \
+		{ NFSERR_TOOSMALL,		"TOOSMALL" }, \
+		{ NFSERR_SERVERFAULT,		"REMOTEIO" }, \
+		{ NFSERR_BADTYPE,		"BADTYPE" }, \
+		{ NFSERR_JUKEBOX,		"JUKEBOX" })
+
+TRACE_DEFINE_ENUM(NFS_UNSTABLE);
+TRACE_DEFINE_ENUM(NFS_DATA_SYNC);
+TRACE_DEFINE_ENUM(NFS_FILE_SYNC);
+
+#define show_nfs_stable_how(x) \
+	__print_symbolic(x, \
+		{ NFS_UNSTABLE,			"UNSTABLE" }, \
+		{ NFS_DATA_SYNC,		"DATA_SYNC" }, \
+		{ NFS_FILE_SYNC,		"FILE_SYNC" })
+
+TRACE_DEFINE_ENUM(NFS4_OK);
+TRACE_DEFINE_ENUM(NFS4ERR_ACCESS);
+TRACE_DEFINE_ENUM(NFS4ERR_ATTRNOTSUPP);
+TRACE_DEFINE_ENUM(NFS4ERR_ADMIN_REVOKED);
+TRACE_DEFINE_ENUM(NFS4ERR_BACK_CHAN_BUSY);
+TRACE_DEFINE_ENUM(NFS4ERR_BADCHAR);
+TRACE_DEFINE_ENUM(NFS4ERR_BADHANDLE);
+TRACE_DEFINE_ENUM(NFS4ERR_BADIOMODE);
+TRACE_DEFINE_ENUM(NFS4ERR_BADLAYOUT);
+TRACE_DEFINE_ENUM(NFS4ERR_BADLABEL);
+TRACE_DEFINE_ENUM(NFS4ERR_BADNAME);
+TRACE_DEFINE_ENUM(NFS4ERR_BADOWNER);
+TRACE_DEFINE_ENUM(NFS4ERR_BADSESSION);
+TRACE_DEFINE_ENUM(NFS4ERR_BADSLOT);
+TRACE_DEFINE_ENUM(NFS4ERR_BADTYPE);
+TRACE_DEFINE_ENUM(NFS4ERR_BADXDR);
+TRACE_DEFINE_ENUM(NFS4ERR_BAD_COOKIE);
+TRACE_DEFINE_ENUM(NFS4ERR_BAD_HIGH_SLOT);
+TRACE_DEFINE_ENUM(NFS4ERR_BAD_RANGE);
+TRACE_DEFINE_ENUM(NFS4ERR_BAD_SEQID);
+TRACE_DEFINE_ENUM(NFS4ERR_BAD_SESSION_DIGEST);
+TRACE_DEFINE_ENUM(NFS4ERR_BAD_STATEID);
+TRACE_DEFINE_ENUM(NFS4ERR_CB_PATH_DOWN);
+TRACE_DEFINE_ENUM(NFS4ERR_CLID_INUSE);
+TRACE_DEFINE_ENUM(NFS4ERR_CLIENTID_BUSY);
+TRACE_DEFINE_ENUM(NFS4ERR_COMPLETE_ALREADY);
+TRACE_DEFINE_ENUM(NFS4ERR_CONN_NOT_BOUND_TO_SESSION);
+TRACE_DEFINE_ENUM(NFS4ERR_DEADLOCK);
+TRACE_DEFINE_ENUM(NFS4ERR_DEADSESSION);
+TRACE_DEFINE_ENUM(NFS4ERR_DELAY);
+TRACE_DEFINE_ENUM(NFS4ERR_DELEG_ALREADY_WANTED);
+TRACE_DEFINE_ENUM(NFS4ERR_DELEG_REVOKED);
+TRACE_DEFINE_ENUM(NFS4ERR_DENIED);
+TRACE_DEFINE_ENUM(NFS4ERR_DIRDELEG_UNAVAIL);
+TRACE_DEFINE_ENUM(NFS4ERR_DQUOT);
+TRACE_DEFINE_ENUM(NFS4ERR_ENCR_ALG_UNSUPP);
+TRACE_DEFINE_ENUM(NFS4ERR_EXIST);
+TRACE_DEFINE_ENUM(NFS4ERR_EXPIRED);
+TRACE_DEFINE_ENUM(NFS4ERR_FBIG);
+TRACE_DEFINE_ENUM(NFS4ERR_FHEXPIRED);
+TRACE_DEFINE_ENUM(NFS4ERR_FILE_OPEN);
+TRACE_DEFINE_ENUM(NFS4ERR_GRACE);
+TRACE_DEFINE_ENUM(NFS4ERR_HASH_ALG_UNSUPP);
+TRACE_DEFINE_ENUM(NFS4ERR_INVAL);
+TRACE_DEFINE_ENUM(NFS4ERR_IO);
+TRACE_DEFINE_ENUM(NFS4ERR_ISDIR);
+TRACE_DEFINE_ENUM(NFS4ERR_LAYOUTTRYLATER);
+TRACE_DEFINE_ENUM(NFS4ERR_LAYOUTUNAVAILABLE);
+TRACE_DEFINE_ENUM(NFS4ERR_LEASE_MOVED);
+TRACE_DEFINE_ENUM(NFS4ERR_LOCKED);
+TRACE_DEFINE_ENUM(NFS4ERR_LOCKS_HELD);
+TRACE_DEFINE_ENUM(NFS4ERR_LOCK_RANGE);
+TRACE_DEFINE_ENUM(NFS4ERR_MINOR_VERS_MISMATCH);
+TRACE_DEFINE_ENUM(NFS4ERR_MLINK);
+TRACE_DEFINE_ENUM(NFS4ERR_MOVED);
+TRACE_DEFINE_ENUM(NFS4ERR_NAMETOOLONG);
+TRACE_DEFINE_ENUM(NFS4ERR_NOENT);
+TRACE_DEFINE_ENUM(NFS4ERR_NOFILEHANDLE);
+TRACE_DEFINE_ENUM(NFS4ERR_NOMATCHING_LAYOUT);
+TRACE_DEFINE_ENUM(NFS4ERR_NOSPC);
+TRACE_DEFINE_ENUM(NFS4ERR_NOTDIR);
+TRACE_DEFINE_ENUM(NFS4ERR_NOTEMPTY);
+TRACE_DEFINE_ENUM(NFS4ERR_NOTSUPP);
+TRACE_DEFINE_ENUM(NFS4ERR_NOT_ONLY_OP);
+TRACE_DEFINE_ENUM(NFS4ERR_NOT_SAME);
+TRACE_DEFINE_ENUM(NFS4ERR_NO_GRACE);
+TRACE_DEFINE_ENUM(NFS4ERR_NXIO);
+TRACE_DEFINE_ENUM(NFS4ERR_OLD_STATEID);
+TRACE_DEFINE_ENUM(NFS4ERR_OPENMODE);
+TRACE_DEFINE_ENUM(NFS4ERR_OP_ILLEGAL);
+TRACE_DEFINE_ENUM(NFS4ERR_OP_NOT_IN_SESSION);
+TRACE_DEFINE_ENUM(NFS4ERR_PERM);
+TRACE_DEFINE_ENUM(NFS4ERR_PNFS_IO_HOLE);
+TRACE_DEFINE_ENUM(NFS4ERR_PNFS_NO_LAYOUT);
+TRACE_DEFINE_ENUM(NFS4ERR_RECALLCONFLICT);
+TRACE_DEFINE_ENUM(NFS4ERR_RECLAIM_BAD);
+TRACE_DEFINE_ENUM(NFS4ERR_RECLAIM_CONFLICT);
+TRACE_DEFINE_ENUM(NFS4ERR_REJECT_DELEG);
+TRACE_DEFINE_ENUM(NFS4ERR_REP_TOO_BIG);
+TRACE_DEFINE_ENUM(NFS4ERR_REP_TOO_BIG_TO_CACHE);
+TRACE_DEFINE_ENUM(NFS4ERR_REQ_TOO_BIG);
+TRACE_DEFINE_ENUM(NFS4ERR_RESOURCE);
+TRACE_DEFINE_ENUM(NFS4ERR_RESTOREFH);
+TRACE_DEFINE_ENUM(NFS4ERR_RETRY_UNCACHED_REP);
+TRACE_DEFINE_ENUM(NFS4ERR_RETURNCONFLICT);
+TRACE_DEFINE_ENUM(NFS4ERR_ROFS);
+TRACE_DEFINE_ENUM(NFS4ERR_SAME);
+TRACE_DEFINE_ENUM(NFS4ERR_SHARE_DENIED);
+TRACE_DEFINE_ENUM(NFS4ERR_SEQUENCE_POS);
+TRACE_DEFINE_ENUM(NFS4ERR_SEQ_FALSE_RETRY);
+TRACE_DEFINE_ENUM(NFS4ERR_SEQ_MISORDERED);
+TRACE_DEFINE_ENUM(NFS4ERR_SERVERFAULT);
+TRACE_DEFINE_ENUM(NFS4ERR_STALE);
+TRACE_DEFINE_ENUM(NFS4ERR_STALE_CLIENTID);
+TRACE_DEFINE_ENUM(NFS4ERR_STALE_STATEID);
+TRACE_DEFINE_ENUM(NFS4ERR_SYMLINK);
+TRACE_DEFINE_ENUM(NFS4ERR_TOOSMALL);
+TRACE_DEFINE_ENUM(NFS4ERR_TOO_MANY_OPS);
+TRACE_DEFINE_ENUM(NFS4ERR_UNKNOWN_LAYOUTTYPE);
+TRACE_DEFINE_ENUM(NFS4ERR_UNSAFE_COMPOUND);
+TRACE_DEFINE_ENUM(NFS4ERR_WRONGSEC);
+TRACE_DEFINE_ENUM(NFS4ERR_WRONG_CRED);
+TRACE_DEFINE_ENUM(NFS4ERR_WRONG_TYPE);
+TRACE_DEFINE_ENUM(NFS4ERR_XDEV);
+
+TRACE_DEFINE_ENUM(NFS4ERR_RESET_TO_MDS);
+TRACE_DEFINE_ENUM(NFS4ERR_RESET_TO_PNFS);
+
+#define show_nfs4_status(x) \
+	__print_symbolic(x, \
+		{ NFS4_OK,			"OK" }, \
+		{ EPERM,			"EPERM" }, \
+		{ ENOENT,			"ENOENT" }, \
+		{ EIO,				"EIO" }, \
+		{ ENXIO,			"ENXIO" }, \
+		{ EACCES,			"EACCES" }, \
+		{ EEXIST,			"EEXIST" }, \
+		{ EXDEV,			"EXDEV" }, \
+		{ ENOTDIR,			"ENOTDIR" }, \
+		{ EISDIR,			"EISDIR" }, \
+		{ EFBIG,			"EFBIG" }, \
+		{ ENOSPC,			"ENOSPC" }, \
+		{ EROFS,			"EROFS" }, \
+		{ EMLINK,			"EMLINK" }, \
+		{ ENAMETOOLONG,			"ENAMETOOLONG" }, \
+		{ ENOTEMPTY,			"ENOTEMPTY" }, \
+		{ EDQUOT,			"EDQUOT" }, \
+		{ ESTALE,			"ESTALE" }, \
+		{ EBADHANDLE,			"EBADHANDLE" }, \
+		{ EBADCOOKIE,			"EBADCOOKIE" }, \
+		{ ENOTSUPP,			"ENOTSUPP" }, \
+		{ ETOOSMALL,			"ETOOSMALL" }, \
+		{ EREMOTEIO,			"EREMOTEIO" }, \
+		{ EBADTYPE,			"EBADTYPE" }, \
+		{ EAGAIN,			"EAGAIN" }, \
+		{ ELOOP,			"ELOOP" }, \
+		{ EOPNOTSUPP,			"EOPNOTSUPP" }, \
+		{ EDEADLK,			"EDEADLK" }, \
+		{ ENOMEM,			"ENOMEM" }, \
+		{ EKEYEXPIRED,			"EKEYEXPIRED" }, \
+		{ ETIMEDOUT,			"ETIMEDOUT" }, \
+		{ ERESTARTSYS,			"ERESTARTSYS" }, \
+		{ ECONNREFUSED,			"ECONNREFUSED" }, \
+		{ ECONNRESET,			"ECONNRESET" }, \
+		{ ENETUNREACH,			"ENETUNREACH" }, \
+		{ EHOSTUNREACH,			"EHOSTUNREACH" }, \
+		{ EHOSTDOWN,			"EHOSTDOWN" }, \
+		{ EPIPE,			"EPIPE" }, \
+		{ EPFNOSUPPORT,			"EPFNOSUPPORT" }, \
+		{ EPROTONOSUPPORT,		"EPROTONOSUPPORT" }, \
+		{ NFS4ERR_ACCESS,		"ACCESS" }, \
+		{ NFS4ERR_ATTRNOTSUPP,		"ATTRNOTSUPP" }, \
+		{ NFS4ERR_ADMIN_REVOKED,	"ADMIN_REVOKED" }, \
+		{ NFS4ERR_BACK_CHAN_BUSY,	"BACK_CHAN_BUSY" }, \
+		{ NFS4ERR_BADCHAR,		"BADCHAR" }, \
+		{ NFS4ERR_BADHANDLE,		"BADHANDLE" }, \
+		{ NFS4ERR_BADIOMODE,		"BADIOMODE" }, \
+		{ NFS4ERR_BADLAYOUT,		"BADLAYOUT" }, \
+		{ NFS4ERR_BADLABEL,		"BADLABEL" }, \
+		{ NFS4ERR_BADNAME,		"BADNAME" }, \
+		{ NFS4ERR_BADOWNER,		"BADOWNER" }, \
+		{ NFS4ERR_BADSESSION,		"BADSESSION" }, \
+		{ NFS4ERR_BADSLOT,		"BADSLOT" }, \
+		{ NFS4ERR_BADTYPE,		"BADTYPE" }, \
+		{ NFS4ERR_BADXDR,		"BADXDR" }, \
+		{ NFS4ERR_BAD_COOKIE,		"BAD_COOKIE" }, \
+		{ NFS4ERR_BAD_HIGH_SLOT,	"BAD_HIGH_SLOT" }, \
+		{ NFS4ERR_BAD_RANGE,		"BAD_RANGE" }, \
+		{ NFS4ERR_BAD_SEQID,		"BAD_SEQID" }, \
+		{ NFS4ERR_BAD_SESSION_DIGEST,	"BAD_SESSION_DIGEST" }, \
+		{ NFS4ERR_BAD_STATEID,		"BAD_STATEID" }, \
+		{ NFS4ERR_CB_PATH_DOWN,		"CB_PATH_DOWN" }, \
+		{ NFS4ERR_CLID_INUSE,		"CLID_INUSE" }, \
+		{ NFS4ERR_CLIENTID_BUSY,	"CLIENTID_BUSY" }, \
+		{ NFS4ERR_COMPLETE_ALREADY,	"COMPLETE_ALREADY" }, \
+		{ NFS4ERR_CONN_NOT_BOUND_TO_SESSION, "CONN_NOT_BOUND_TO_SESSION" }, \
+		{ NFS4ERR_DEADLOCK,		"DEADLOCK" }, \
+		{ NFS4ERR_DEADSESSION,		"DEAD_SESSION" }, \
+		{ NFS4ERR_DELAY,		"DELAY" }, \
+		{ NFS4ERR_DELEG_ALREADY_WANTED,	"DELEG_ALREADY_WANTED" }, \
+		{ NFS4ERR_DELEG_REVOKED,	"DELEG_REVOKED" }, \
+		{ NFS4ERR_DENIED,		"DENIED" }, \
+		{ NFS4ERR_DIRDELEG_UNAVAIL,	"DIRDELEG_UNAVAIL" }, \
+		{ NFS4ERR_DQUOT,		"DQUOT" }, \
+		{ NFS4ERR_ENCR_ALG_UNSUPP,	"ENCR_ALG_UNSUPP" }, \
+		{ NFS4ERR_EXIST,		"EXIST" }, \
+		{ NFS4ERR_EXPIRED,		"EXPIRED" }, \
+		{ NFS4ERR_FBIG,			"FBIG" }, \
+		{ NFS4ERR_FHEXPIRED,		"FHEXPIRED" }, \
+		{ NFS4ERR_FILE_OPEN,		"FILE_OPEN" }, \
+		{ NFS4ERR_GRACE,		"GRACE" }, \
+		{ NFS4ERR_HASH_ALG_UNSUPP,	"HASH_ALG_UNSUPP" }, \
+		{ NFS4ERR_INVAL,		"INVAL" }, \
+		{ NFS4ERR_IO,			"IO" }, \
+		{ NFS4ERR_ISDIR,		"ISDIR" }, \
+		{ NFS4ERR_LAYOUTTRYLATER,	"LAYOUTTRYLATER" }, \
+		{ NFS4ERR_LAYOUTUNAVAILABLE,	"LAYOUTUNAVAILABLE" }, \
+		{ NFS4ERR_LEASE_MOVED,		"LEASE_MOVED" }, \
+		{ NFS4ERR_LOCKED,		"LOCKED" }, \
+		{ NFS4ERR_LOCKS_HELD,		"LOCKS_HELD" }, \
+		{ NFS4ERR_LOCK_RANGE,		"LOCK_RANGE" }, \
+		{ NFS4ERR_MINOR_VERS_MISMATCH,	"MINOR_VERS_MISMATCH" }, \
+		{ NFS4ERR_MLINK,		"MLINK" }, \
+		{ NFS4ERR_MOVED,		"MOVED" }, \
+		{ NFS4ERR_NAMETOOLONG,		"NAMETOOLONG" }, \
+		{ NFS4ERR_NOENT,		"NOENT" }, \
+		{ NFS4ERR_NOFILEHANDLE,		"NOFILEHANDLE" }, \
+		{ NFS4ERR_NOMATCHING_LAYOUT,	"NOMATCHING_LAYOUT" }, \
+		{ NFS4ERR_NOSPC,		"NOSPC" }, \
+		{ NFS4ERR_NOTDIR,		"NOTDIR" }, \
+		{ NFS4ERR_NOTEMPTY,		"NOTEMPTY" }, \
+		{ NFS4ERR_NOTSUPP,		"NOTSUPP" }, \
+		{ NFS4ERR_NOT_ONLY_OP,		"NOT_ONLY_OP" }, \
+		{ NFS4ERR_NOT_SAME,		"NOT_SAME" }, \
+		{ NFS4ERR_NO_GRACE,		"NO_GRACE" }, \
+		{ NFS4ERR_NXIO,			"NXIO" }, \
+		{ NFS4ERR_OLD_STATEID,		"OLD_STATEID" }, \
+		{ NFS4ERR_OPENMODE,		"OPENMODE" }, \
+		{ NFS4ERR_OP_ILLEGAL,		"OP_ILLEGAL" }, \
+		{ NFS4ERR_OP_NOT_IN_SESSION,	"OP_NOT_IN_SESSION" }, \
+		{ NFS4ERR_PERM,			"PERM" }, \
+		{ NFS4ERR_PNFS_IO_HOLE,		"PNFS_IO_HOLE" }, \
+		{ NFS4ERR_PNFS_NO_LAYOUT,	"PNFS_NO_LAYOUT" }, \
+		{ NFS4ERR_RECALLCONFLICT,	"RECALLCONFLICT" }, \
+		{ NFS4ERR_RECLAIM_BAD,		"RECLAIM_BAD" }, \
+		{ NFS4ERR_RECLAIM_CONFLICT,	"RECLAIM_CONFLICT" }, \
+		{ NFS4ERR_REJECT_DELEG,		"REJECT_DELEG" }, \
+		{ NFS4ERR_REP_TOO_BIG,		"REP_TOO_BIG" }, \
+		{ NFS4ERR_REP_TOO_BIG_TO_CACHE,	"REP_TOO_BIG_TO_CACHE" }, \
+		{ NFS4ERR_REQ_TOO_BIG,		"REQ_TOO_BIG" }, \
+		{ NFS4ERR_RESOURCE,		"RESOURCE" }, \
+		{ NFS4ERR_RESTOREFH,		"RESTOREFH" }, \
+		{ NFS4ERR_RETRY_UNCACHED_REP,	"RETRY_UNCACHED_REP" }, \
+		{ NFS4ERR_RETURNCONFLICT,	"RETURNCONFLICT" }, \
+		{ NFS4ERR_ROFS,			"ROFS" }, \
+		{ NFS4ERR_SAME,			"SAME" }, \
+		{ NFS4ERR_SHARE_DENIED,		"SHARE_DENIED" }, \
+		{ NFS4ERR_SEQUENCE_POS,		"SEQUENCE_POS" }, \
+		{ NFS4ERR_SEQ_FALSE_RETRY,	"SEQ_FALSE_RETRY" }, \
+		{ NFS4ERR_SEQ_MISORDERED,	"SEQ_MISORDERED" }, \
+		{ NFS4ERR_SERVERFAULT,		"SERVERFAULT" }, \
+		{ NFS4ERR_STALE,		"STALE" }, \
+		{ NFS4ERR_STALE_CLIENTID,	"STALE_CLIENTID" }, \
+		{ NFS4ERR_STALE_STATEID,	"STALE_STATEID" }, \
+		{ NFS4ERR_SYMLINK,		"SYMLINK" }, \
+		{ NFS4ERR_TOOSMALL,		"TOOSMALL" }, \
+		{ NFS4ERR_TOO_MANY_OPS,		"TOO_MANY_OPS" }, \
+		{ NFS4ERR_UNKNOWN_LAYOUTTYPE,	"UNKNOWN_LAYOUTTYPE" }, \
+		{ NFS4ERR_UNSAFE_COMPOUND,	"UNSAFE_COMPOUND" }, \
+		{ NFS4ERR_WRONGSEC,		"WRONGSEC" }, \
+		{ NFS4ERR_WRONG_CRED,		"WRONG_CRED" }, \
+		{ NFS4ERR_WRONG_TYPE,		"WRONG_TYPE" }, \
+		{ NFS4ERR_XDEV,			"XDEV" }, \
+		/* ***** Internal to Linux NFS client ***** */ \
+		{ NFS4ERR_RESET_TO_MDS,		"RESET_TO_MDS" }, \
+		{ NFS4ERR_RESET_TO_PNFS,	"RESET_TO_PNFS" })
+
+#define show_nfs4_verifier(x) \
+	__print_hex_str(x, NFS4_VERIFIER_SIZE)
+
+TRACE_DEFINE_ENUM(IOMODE_READ);
+TRACE_DEFINE_ENUM(IOMODE_RW);
+TRACE_DEFINE_ENUM(IOMODE_ANY);
+
+#define show_pnfs_layout_iomode(x) \
+	__print_symbolic(x, \
+		{ IOMODE_READ,			"READ" }, \
+		{ IOMODE_RW,			"RW" }, \
+		{ IOMODE_ANY,			"ANY" })
+
+#define show_rca_mask(x) \
+	__print_flags(x, "|", \
+		{ BIT(RCA4_TYPE_MASK_RDATA_DLG),	"RDATA_DLG" }, \
+		{ BIT(RCA4_TYPE_MASK_WDATA_DLG),	"WDATA_DLG" }, \
+		{ BIT(RCA4_TYPE_MASK_DIR_DLG),		"DIR_DLG" }, \
+		{ BIT(RCA4_TYPE_MASK_FILE_LAYOUT),	"FILE_LAYOUT" }, \
+		{ BIT(RCA4_TYPE_MASK_BLK_LAYOUT),	"BLK_LAYOUT" }, \
+		{ BIT(RCA4_TYPE_MASK_OBJ_LAYOUT_MIN),	"OBJ_LAYOUT_MIN" }, \
+		{ BIT(RCA4_TYPE_MASK_OBJ_LAYOUT_MAX),	"OBJ_LAYOUT_MAX" }, \
+		{ BIT(RCA4_TYPE_MASK_OTHER_LAYOUT_MIN),	"OTHER_LAYOUT_MIN" }, \
+		{ BIT(RCA4_TYPE_MASK_OTHER_LAYOUT_MAX),	"OTHER_LAYOUT_MAX" })
+
+#define show_nfs4_seq4_status(x) \
+	__print_flags(x, "|", \
+		{ SEQ4_STATUS_CB_PATH_DOWN,		"CB_PATH_DOWN" }, \
+		{ SEQ4_STATUS_CB_GSS_CONTEXTS_EXPIRING,	"CB_GSS_CONTEXTS_EXPIRING" }, \
+		{ SEQ4_STATUS_CB_GSS_CONTEXTS_EXPIRED,	"CB_GSS_CONTEXTS_EXPIRED" }, \
+		{ SEQ4_STATUS_EXPIRED_ALL_STATE_REVOKED, "EXPIRED_ALL_STATE_REVOKED" }, \
+		{ SEQ4_STATUS_EXPIRED_SOME_STATE_REVOKED, "EXPIRED_SOME_STATE_REVOKED" }, \
+		{ SEQ4_STATUS_ADMIN_STATE_REVOKED,	"ADMIN_STATE_REVOKED" }, \
+		{ SEQ4_STATUS_RECALLABLE_STATE_REVOKED,	"RECALLABLE_STATE_REVOKED" }, \
+		{ SEQ4_STATUS_LEASE_MOVED,		"LEASE_MOVED" }, \
+		{ SEQ4_STATUS_RESTART_RECLAIM_NEEDED,	"RESTART_RECLAIM_NEEDED" }, \
+		{ SEQ4_STATUS_CB_PATH_DOWN_SESSION,	"CB_PATH_DOWN_SESSION" }, \
+		{ SEQ4_STATUS_BACKCHANNEL_FAULT,	"BACKCHANNEL_FAULT" })
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/misc/rdma.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/misc/rdma.h
@@ -0,0 +1,168 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017 Oracle.  All rights reserved.
+ */
+
+/*
+ * enum ib_event_type, from include/rdma/ib_verbs.h
+ */
+#define IB_EVENT_LIST				\
+	ib_event(CQ_ERR)			\
+	ib_event(QP_FATAL)			\
+	ib_event(QP_REQ_ERR)			\
+	ib_event(QP_ACCESS_ERR)			\
+	ib_event(COMM_EST)			\
+	ib_event(SQ_DRAINED)			\
+	ib_event(PATH_MIG)			\
+	ib_event(PATH_MIG_ERR)			\
+	ib_event(DEVICE_FATAL)			\
+	ib_event(PORT_ACTIVE)			\
+	ib_event(PORT_ERR)			\
+	ib_event(LID_CHANGE)			\
+	ib_event(PKEY_CHANGE)			\
+	ib_event(SM_CHANGE)			\
+	ib_event(SRQ_ERR)			\
+	ib_event(SRQ_LIMIT_REACHED)		\
+	ib_event(QP_LAST_WQE_REACHED)		\
+	ib_event(CLIENT_REREGISTER)		\
+	ib_event(GID_CHANGE)			\
+	ib_event_end(WQ_FATAL)
+
+#undef ib_event
+#undef ib_event_end
+
+#define ib_event(x)		TRACE_DEFINE_ENUM(IB_EVENT_##x);
+#define ib_event_end(x)		TRACE_DEFINE_ENUM(IB_EVENT_##x);
+
+IB_EVENT_LIST
+
+#undef ib_event
+#undef ib_event_end
+
+#define ib_event(x)		{ IB_EVENT_##x, #x },
+#define ib_event_end(x)		{ IB_EVENT_##x, #x }
+
+#define rdma_show_ib_event(x) \
+		__print_symbolic(x, IB_EVENT_LIST)
+
+/*
+ * enum ib_wc_status type, from include/rdma/ib_verbs.h
+ */
+#define IB_WC_STATUS_LIST			\
+	ib_wc_status(SUCCESS)			\
+	ib_wc_status(LOC_LEN_ERR)		\
+	ib_wc_status(LOC_QP_OP_ERR)		\
+	ib_wc_status(LOC_EEC_OP_ERR)		\
+	ib_wc_status(LOC_PROT_ERR)		\
+	ib_wc_status(WR_FLUSH_ERR)		\
+	ib_wc_status(MW_BIND_ERR)		\
+	ib_wc_status(BAD_RESP_ERR)		\
+	ib_wc_status(LOC_ACCESS_ERR)		\
+	ib_wc_status(REM_INV_REQ_ERR)		\
+	ib_wc_status(REM_ACCESS_ERR)		\
+	ib_wc_status(REM_OP_ERR)		\
+	ib_wc_status(RETRY_EXC_ERR)		\
+	ib_wc_status(RNR_RETRY_EXC_ERR)		\
+	ib_wc_status(LOC_RDD_VIOL_ERR)		\
+	ib_wc_status(REM_INV_RD_REQ_ERR)	\
+	ib_wc_status(REM_ABORT_ERR)		\
+	ib_wc_status(INV_EECN_ERR)		\
+	ib_wc_status(INV_EEC_STATE_ERR)		\
+	ib_wc_status(FATAL_ERR)			\
+	ib_wc_status(RESP_TIMEOUT_ERR)		\
+	ib_wc_status_end(GENERAL_ERR)
+
+#undef ib_wc_status
+#undef ib_wc_status_end
+
+#define ib_wc_status(x)		TRACE_DEFINE_ENUM(IB_WC_##x);
+#define ib_wc_status_end(x)	TRACE_DEFINE_ENUM(IB_WC_##x);
+
+IB_WC_STATUS_LIST
+
+#undef ib_wc_status
+#undef ib_wc_status_end
+
+#define ib_wc_status(x)		{ IB_WC_##x, #x },
+#define ib_wc_status_end(x)	{ IB_WC_##x, #x }
+
+#define rdma_show_wc_status(x) \
+		__print_symbolic(x, IB_WC_STATUS_LIST)
+
+/*
+ * enum ib_cm_event_type, from include/rdma/ib_cm.h
+ */
+#define IB_CM_EVENT_LIST			\
+	ib_cm_event(REQ_ERROR)			\
+	ib_cm_event(REQ_RECEIVED)		\
+	ib_cm_event(REP_ERROR)			\
+	ib_cm_event(REP_RECEIVED)		\
+	ib_cm_event(RTU_RECEIVED)		\
+	ib_cm_event(USER_ESTABLISHED)		\
+	ib_cm_event(DREQ_ERROR)			\
+	ib_cm_event(DREQ_RECEIVED)		\
+	ib_cm_event(DREP_RECEIVED)		\
+	ib_cm_event(TIMEWAIT_EXIT)		\
+	ib_cm_event(MRA_RECEIVED)		\
+	ib_cm_event(REJ_RECEIVED)		\
+	ib_cm_event(LAP_ERROR)			\
+	ib_cm_event(LAP_RECEIVED)		\
+	ib_cm_event(APR_RECEIVED)		\
+	ib_cm_event(SIDR_REQ_ERROR)		\
+	ib_cm_event(SIDR_REQ_RECEIVED)		\
+	ib_cm_event_end(SIDR_REP_RECEIVED)
+
+#undef ib_cm_event
+#undef ib_cm_event_end
+
+#define ib_cm_event(x)		TRACE_DEFINE_ENUM(IB_CM_##x);
+#define ib_cm_event_end(x)	TRACE_DEFINE_ENUM(IB_CM_##x);
+
+IB_CM_EVENT_LIST
+
+#undef ib_cm_event
+#undef ib_cm_event_end
+
+#define ib_cm_event(x)		{ IB_CM_##x, #x },
+#define ib_cm_event_end(x)	{ IB_CM_##x, #x }
+
+#define rdma_show_ib_cm_event(x) \
+		__print_symbolic(x, IB_CM_EVENT_LIST)
+
+/*
+ * enum rdma_cm_event_type, from include/rdma/rdma_cm.h
+ */
+#define RDMA_CM_EVENT_LIST			\
+	rdma_cm_event(ADDR_RESOLVED)		\
+	rdma_cm_event(ADDR_ERROR)		\
+	rdma_cm_event(ROUTE_RESOLVED)		\
+	rdma_cm_event(ROUTE_ERROR)		\
+	rdma_cm_event(CONNECT_REQUEST)		\
+	rdma_cm_event(CONNECT_RESPONSE)		\
+	rdma_cm_event(CONNECT_ERROR)		\
+	rdma_cm_event(UNREACHABLE)		\
+	rdma_cm_event(REJECTED)			\
+	rdma_cm_event(ESTABLISHED)		\
+	rdma_cm_event(DISCONNECTED)		\
+	rdma_cm_event(DEVICE_REMOVAL)		\
+	rdma_cm_event(MULTICAST_JOIN)		\
+	rdma_cm_event(MULTICAST_ERROR)		\
+	rdma_cm_event(ADDR_CHANGE)		\
+	rdma_cm_event_end(TIMEWAIT_EXIT)
+
+#undef rdma_cm_event
+#undef rdma_cm_event_end
+
+#define rdma_cm_event(x)	TRACE_DEFINE_ENUM(RDMA_CM_EVENT_##x);
+#define rdma_cm_event_end(x)	TRACE_DEFINE_ENUM(RDMA_CM_EVENT_##x);
+
+RDMA_CM_EVENT_LIST
+
+#undef rdma_cm_event
+#undef rdma_cm_event_end
+
+#define rdma_cm_event(x)	{ RDMA_CM_EVENT_##x, #x },
+#define rdma_cm_event_end(x)	{ RDMA_CM_EVENT_##x, #x }
+
+#define rdma_show_cm_event(x) \
+		__print_symbolic(x, RDMA_CM_EVENT_LIST)
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/misc/sunrpc.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/misc/sunrpc.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Oracle and/or its affiliates.
+ *
+ * Common types and format specifiers for sunrpc.
+ */
+
+#if !defined(_TRACE_SUNRPC_BASE_H)
+#define _TRACE_SUNRPC_BASE_H
+
+#include <linux/tracepoint.h>
+
+#define SUNRPC_TRACE_PID_SPECIFIER	"%08x"
+#define SUNRPC_TRACE_CLID_SPECIFIER	"%08x"
+#define SUNRPC_TRACE_TASK_SPECIFIER \
+	"task:" SUNRPC_TRACE_PID_SPECIFIER "@" SUNRPC_TRACE_CLID_SPECIFIER
+
+#endif /* _TRACE_SUNRPC_BASE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/perf.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/perf.h
@@ -21,6 +21,29 @@
 #undef __get_bitmask
 #define __get_bitmask(field) (char *)__get_dynamic_array(field)
 
+#undef __get_sockaddr
+#define __get_sockaddr(field) ((struct sockaddr *)__get_dynamic_array(field))
+
+#undef __get_rel_dynamic_array
+#define __get_rel_dynamic_array(field)	\
+		((void *)__entry +					\
+		 offsetof(typeof(*__entry), __rel_loc_##field) +	\
+		 sizeof(__entry->__rel_loc_##field) +			\
+		 (__entry->__rel_loc_##field & 0xffff))
+
+#undef __get_rel_dynamic_array_len
+#define __get_rel_dynamic_array_len(field)	\
+		((__entry->__rel_loc_##field >> 16) & 0xffff)
+
+#undef __get_rel_str
+#define __get_rel_str(field) ((char *)__get_rel_dynamic_array(field))
+
+#undef __get_rel_bitmask
+#define __get_rel_bitmask(field) (char *)__get_rel_dynamic_array(field)
+
+#undef __get_rel_sockaddr
+#define __get_rel_sockaddr(field) ((struct sockaddr *)__get_rel_dynamic_array(field))
+
 #undef __perf_count
 #define __perf_count(c)	(__count = (c))
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/trace/trace_events.h
+++ linux-xilinx-zynqmp-5.15.0/include/trace/trace_events.h
@@ -108,6 +108,24 @@
 #undef __bitmask
 #define __bitmask(item, nr_bits) __dynamic_array(char, item, -1)
 
+#undef __sockaddr
+#define __sockaddr(field, len) __dynamic_array(u8, field, len)
+
+#undef __rel_dynamic_array
+#define __rel_dynamic_array(type, item, len) u32 __rel_loc_##item;
+
+#undef __rel_string
+#define __rel_string(item, src) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_string_len
+#define __rel_string_len(item, src, len) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_bitmask
+#define __rel_bitmask(item, nr_bits) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_sockaddr
+#define __rel_sockaddr(field, len) __rel_dynamic_array(u8, field, len)
+
 #undef TP_STRUCT__entry
 #define TP_STRUCT__entry(args...) args
 
@@ -116,7 +134,7 @@
 	struct trace_event_raw_##name {					\
 		struct trace_entry	ent;				\
 		tstruct							\
-		char			__data[0];			\
+		char			__data[];			\
 	};								\
 									\
 	static struct trace_event_class event_class_##name;
@@ -206,6 +224,24 @@
 #undef __bitmask
 #define __bitmask(item, nr_bits) __dynamic_array(unsigned long, item, -1)
 
+#undef __sockaddr
+#define __sockaddr(field, len) __dynamic_array(u8, field, len)
+
+#undef __rel_dynamic_array
+#define __rel_dynamic_array(type, item, len)	u32 item;
+
+#undef __rel_string
+#define __rel_string(item, src) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_string_len
+#define __rel_string_len(item, src, len) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_bitmask
+#define __rel_bitmask(item, nr_bits) __rel_dynamic_array(unsigned long, item, -1)
+
+#undef __rel_sockaddr
+#define __rel_sockaddr(field, len) __rel_dynamic_array(u8, field, len)
+
 #undef DECLARE_EVENT_CLASS
 #define DECLARE_EVENT_CLASS(call, proto, args, tstruct, assign, print)	\
 	struct trace_event_data_offsets_##call {			\
@@ -293,6 +329,20 @@
 #undef __get_str
 #define __get_str(field) ((char *)__get_dynamic_array(field))
 
+#undef __get_rel_dynamic_array
+#define __get_rel_dynamic_array(field)					\
+		((void *)__entry + 					\
+		 offsetof(typeof(*__entry), __rel_loc_##field) +	\
+		 sizeof(__entry->__rel_loc_##field) +			\
+		 (__entry->__rel_loc_##field & 0xffff))
+
+#undef __get_rel_dynamic_array_len
+#define __get_rel_dynamic_array_len(field)	\
+		((__entry->__rel_loc_##field >> 16) & 0xffff)
+
+#undef __get_rel_str
+#define __get_rel_str(field) ((char *)__get_rel_dynamic_array(field))
+
 #undef __get_bitmask
 #define __get_bitmask(field)						\
 	({								\
@@ -302,6 +352,21 @@
 		trace_print_bitmask_seq(p, __bitmask, __bitmask_size);	\
 	})
 
+#undef __get_rel_bitmask
+#define __get_rel_bitmask(field)						\
+	({								\
+		void *__bitmask = __get_rel_dynamic_array(field);		\
+		unsigned int __bitmask_size;				\
+		__bitmask_size = __get_rel_dynamic_array_len(field);	\
+		trace_print_bitmask_seq(p, __bitmask, __bitmask_size);	\
+	})
+
+#undef __get_sockaddr
+#define __get_sockaddr(field)	((struct sockaddr *)__get_dynamic_array(field))
+
+#undef __get_rel_sockaddr
+#define __get_rel_sockaddr(field)	((struct sockaddr *)__get_rel_dynamic_array(field))
+
 #undef __print_flags
 #define __print_flags(flag, delim, flag_array...)			\
 	({								\
@@ -432,16 +497,18 @@
 
 #include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
 
+#define ALIGN_STRUCTFIELD(type) ((int)(__alignof__(struct {type b;})))
+
 #undef __field_ext
 #define __field_ext(_type, _item, _filter_type) {			\
 	.type = #_type, .name = #_item,					\
-	.size = sizeof(_type), .align = __alignof__(_type),		\
+	.size = sizeof(_type), .align = ALIGN_STRUCTFIELD(_type),	\
 	.is_signed = is_signed_type(_type), .filter_type = _filter_type },
 
 #undef __field_struct_ext
 #define __field_struct_ext(_type, _item, _filter_type) {		\
 	.type = #_type, .name = #_item,					\
-	.size = sizeof(_type), .align = __alignof__(_type),		\
+	.size = sizeof(_type), .align = ALIGN_STRUCTFIELD(_type),	\
 	0, .filter_type = _filter_type },
 
 #undef __field
@@ -453,7 +520,7 @@
 #undef __array
 #define __array(_type, _item, _len) {					\
 	.type = #_type"["__stringify(_len)"]", .name = #_item,		\
-	.size = sizeof(_type[_len]), .align = __alignof__(_type),	\
+	.size = sizeof(_type[_len]), .align = ALIGN_STRUCTFIELD(_type),	\
 	.is_signed = is_signed_type(_type), .filter_type = FILTER_OTHER },
 
 #undef __dynamic_array
@@ -471,6 +538,27 @@
 #undef __bitmask
 #define __bitmask(item, nr_bits) __dynamic_array(unsigned long, item, -1)
 
+#undef __sockaddr
+#define __sockaddr(field, len) __dynamic_array(u8, field, len)
+
+#undef __rel_dynamic_array
+#define __rel_dynamic_array(_type, _item, _len) {			\
+	.type = "__rel_loc " #_type "[]", .name = #_item,		\
+	.size = 4, .align = 4,						\
+	.is_signed = is_signed_type(_type), .filter_type = FILTER_OTHER },
+
+#undef __rel_string
+#define __rel_string(item, src) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_string_len
+#define __rel_string_len(item, src, len) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_bitmask
+#define __rel_bitmask(item, nr_bits) __rel_dynamic_array(unsigned long, item, -1)
+
+#undef __rel_sockaddr
+#define __rel_sockaddr(field, len) __rel_dynamic_array(u8, field, len)
+
 #undef DECLARE_EVENT_CLASS
 #define DECLARE_EVENT_CLASS(call, proto, args, tstruct, func, print)	\
 static struct trace_event_fields trace_event_fields_##call[] = {	\
@@ -519,6 +607,22 @@
 #undef __string_len
 #define __string_len(item, src, len) __dynamic_array(char, item, (len) + 1)
 
+#undef __rel_dynamic_array
+#define __rel_dynamic_array(type, item, len)				\
+	__item_length = (len) * sizeof(type);				\
+	__data_offsets->item = __data_size +				\
+			       offsetof(typeof(*entry), __data) -	\
+			       offsetof(typeof(*entry), __rel_loc_##item) -	\
+			       sizeof(u32);				\
+	__data_offsets->item |= __item_length << 16;			\
+	__data_size += __item_length;
+
+#undef __rel_string
+#define __rel_string(item, src) __rel_dynamic_array(char, item,			\
+		    strlen((src) ? (const char *)(src) : "(null)") + 1)
+
+#undef __rel_string_len
+#define __rel_string_len(item, src, len) __rel_dynamic_array(char, item, (len) + 1)
 /*
  * __bitmask_size_in_bytes_raw is the number of bytes needed to hold
  * num_possible_cpus().
@@ -542,6 +646,16 @@
 #define __bitmask(item, nr_bits) __dynamic_array(unsigned long, item,	\
 					 __bitmask_size_in_longs(nr_bits))
 
+#undef __rel_bitmask
+#define __rel_bitmask(item, nr_bits) __rel_dynamic_array(unsigned long, item,	\
+					 __bitmask_size_in_longs(nr_bits))
+
+#undef __sockaddr
+#define __sockaddr(field, len) __dynamic_array(u8, field, len)
+
+#undef __rel_sockaddr
+#define __rel_sockaddr(field, len) __rel_dynamic_array(u8, field, len)
+
 #undef DECLARE_EVENT_CLASS
 #define DECLARE_EVENT_CLASS(call, proto, args, tstruct, assign, print)	\
 static inline notrace int trace_event_get_offsets_##call(		\
@@ -706,6 +820,56 @@
 #define __assign_bitmask(dst, src, nr_bits)					\
 	memcpy(__get_bitmask(dst), (src), __bitmask_size_in_bytes(nr_bits))
 
+#undef __sockaddr
+#define __sockaddr(field, len) __dynamic_array(u8, field, len)
+
+#undef __get_sockaddr
+#define __get_sockaddr(field)	((struct sockaddr *)__get_dynamic_array(field))
+
+#define __assign_sockaddr(dest, src, len)					\
+	memcpy(__get_dynamic_array(dest), src, len)
+
+#undef __rel_dynamic_array
+#define __rel_dynamic_array(type, item, len)				\
+	__entry->__rel_loc_##item = __data_offsets.item;
+
+#undef __rel_string
+#define __rel_string(item, src) __rel_dynamic_array(char, item, -1)
+
+#undef __rel_string_len
+#define __rel_string_len(item, src, len) __rel_dynamic_array(char, item, -1)
+
+#undef __assign_rel_str
+#define __assign_rel_str(dst, src)					\
+	strcpy(__get_rel_str(dst), (src) ? (const char *)(src) : "(null)");
+
+#undef __assign_rel_str_len
+#define __assign_rel_str_len(dst, src, len)				\
+	do {								\
+		memcpy(__get_rel_str(dst), (src), (len));		\
+		__get_rel_str(dst)[len] = '\0';				\
+	} while (0)
+
+#undef __rel_bitmask
+#define __rel_bitmask(item, nr_bits) __rel_dynamic_array(unsigned long, item, -1)
+
+#undef __get_rel_bitmask
+#define __get_rel_bitmask(field) (char *)__get_rel_dynamic_array(field)
+
+#undef __assign_rel_bitmask
+#define __assign_rel_bitmask(dst, src, nr_bits)					\
+	memcpy(__get_rel_bitmask(dst), (src), __bitmask_size_in_bytes(nr_bits))
+
+#undef __rel_sockaddr
+#define __rel_sockaddr(field, len) __rel_dynamic_array(u8, field, len)
+
+#undef __get_rel_sockaddr
+#define __get_rel_sockaddr(field)	((struct sockaddr *)__get_rel_dynamic_array(field))
+
+#define __assign_rel_sockaddr(dest, src, len)					\
+	memcpy(__get_rel_dynamic_array(dest), src, len)
+
+
 #undef TP_fast_assign
 #define TP_fast_assign(args...) args
 
@@ -770,6 +934,12 @@
 #undef __get_dynamic_array_len
 #undef __get_str
 #undef __get_bitmask
+#undef __get_sockaddr
+#undef __get_rel_dynamic_array
+#undef __get_rel_dynamic_array_len
+#undef __get_rel_str
+#undef __get_rel_bitmask
+#undef __get_rel_sockaddr
 #undef __print_array
 #undef __print_hex_dump
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/asm-generic/hugetlb_encode.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/asm-generic/hugetlb_encode.h
@@ -20,18 +20,18 @@
 #define HUGETLB_FLAG_ENCODE_SHIFT	26
 #define HUGETLB_FLAG_ENCODE_MASK	0x3f
 
-#define HUGETLB_FLAG_ENCODE_16KB	(14 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_64KB	(16 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_512KB	(19 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_1MB		(20 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_2MB		(21 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_8MB		(23 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_16MB	(24 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_32MB	(25 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_256MB	(28 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_512MB	(29 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_1GB		(30 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_2GB		(31 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_16GB	(34 << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_16KB	(14U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_64KB	(16U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_512KB	(19U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_1MB		(20U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_2MB		(21U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_8MB		(23U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_16MB	(24U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_32MB	(25U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_256MB	(28U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_512MB	(29U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_1GB		(30U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_2GB		(31U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_16GB	(34U << HUGETLB_FLAG_ENCODE_SHIFT)
 
 #endif /* _ASM_GENERIC_HUGETLB_ENCODE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/asm-generic/poll.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/asm-generic/poll.h
@@ -29,7 +29,7 @@
 #define POLLRDHUP       0x2000
 #endif
 
-#define POLLFREE	(__force __poll_t)0x4000	/* currently only for epoll */
+#define POLLFREE	(__force __poll_t)0x4000
 
 #define POLL_BUSY_LOOP	(__force __poll_t)0x8000
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/asm-generic/siginfo.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/asm-generic/siginfo.h
@@ -99,6 +99,7 @@
 			struct {
 				unsigned long _data;
 				__u32 _type;
+				__u32 _flags;
 			} _perf;
 		};
 	} _sigfault;
@@ -164,6 +165,7 @@
 #define si_pkey		_sifields._sigfault._addr_pkey._pkey
 #define si_perf_data	_sifields._sigfault._perf._data
 #define si_perf_type	_sifields._sigfault._perf._type
+#define si_perf_flags	_sifields._sigfault._perf._flags
 #define si_band		_sifields._sigpoll._band
 #define si_fd		_sifields._sigpoll._fd
 #define si_call_addr	_sifields._sigsys._call_addr
@@ -271,6 +273,11 @@
  */
 
 /*
+ * Flags for si_perf_flags if SIGTRAP si_code is TRAP_PERF.
+ */
+#define TRAP_PERF_FLAG_ASYNC (1u << 0)
+
+/*
  * SIGCHLD si_codes
  */
 #define CLD_EXITED	1	/* child has exited */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/asm-generic/signal-defs.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/asm-generic/signal-defs.h
@@ -45,6 +45,7 @@
 #define SA_UNSUPPORTED	0x00000400
 #define SA_EXPOSE_TAGBITS	0x00000800
 /* 0x00010000 used on mips */
+/* 0x00800000 used for internal SA_IMMUTABLE */
 /* 0x01000000 used on x86 */
 /* 0x02000000 used on x86 */
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/asm-generic/unistd.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/asm-generic/unistd.h
@@ -805,7 +805,7 @@
 #define __NR_ppoll_time64 414
 __SC_COMP(__NR_ppoll_time64, sys_ppoll, compat_sys_ppoll_time64)
 #define __NR_io_pgetevents_time64 416
-__SYSCALL(__NR_io_pgetevents_time64, sys_io_pgetevents)
+__SC_COMP(__NR_io_pgetevents_time64, sys_io_pgetevents, compat_sys_io_pgetevents_time64)
 #define __NR_recvmmsg_time64 417
 __SC_COMP(__NR_recvmmsg_time64, sys_recvmmsg, compat_sys_recvmmsg_time64)
 #define __NR_mq_timedsend_time64 418
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/drm/drm_fourcc.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/drm/drm_fourcc.h
@@ -199,8 +199,11 @@
 #define DRM_FORMAT_VYUY		fourcc_code('V', 'Y', 'U', 'Y') /* [31:0] Y1:Cb0:Y0:Cr0 8:8:8:8 little endian */
 
 #define DRM_FORMAT_AYUV		fourcc_code('A', 'Y', 'U', 'V') /* [31:0] A:Y:Cb:Cr 8:8:8:8 little endian */
+#define DRM_FORMAT_AVUY		fourcc_code('A', 'V', 'U', 'Y') /* [31:0] A:Cr:Cb:Y 8:8:8:8 little endian */
 #define DRM_FORMAT_XYUV8888	fourcc_code('X', 'Y', 'U', 'V') /* [31:0] X:Y:Cb:Cr 8:8:8:8 little endian */
 #define DRM_FORMAT_VUY888	fourcc_code('V', 'U', '2', '4') /* [23:0] Cr:Cb:Y 8:8:8 little endian */
+#define DRM_FORMAT_XVUY8888	fourcc_code('X', 'V', '2', '4') /* [31:0] x:Cr:Cb:Y 8:8:8:8 little endian */
+#define DRM_FORMAT_XVUY2101010	fourcc_code('X', 'V', '3', '0') /* [31:0] x:Cr:Cb:Y 2:10:10:10 little endian */
 #define DRM_FORMAT_VUY101010	fourcc_code('V', 'U', '3', '0') /* Y followed by U then V, 10:10:10. Non-linear modifier only */
 
 /*
@@ -246,6 +249,10 @@
 #define DRM_FORMAT_YUV420_8BIT	fourcc_code('Y', 'U', '0', '8')
 #define DRM_FORMAT_YUV420_10BIT	fourcc_code('Y', 'U', '1', '0')
 
+/* Grey scale */
+#define DRM_FORMAT_Y8		fourcc_code('G', 'R', 'E', 'Y') /* 8  Greyscale	*/
+#define DRM_FORMAT_Y10		fourcc_code('Y', '1', '0', ' ') /* 10 Greyscale */
+
 /*
  * 2 plane RGB + A
  * index 0 = RGB plane, same format as the corresponding non _A8 format has
@@ -281,6 +288,14 @@
 #define DRM_FORMAT_NV15		fourcc_code('N', 'V', '1', '5') /* 2x2 subsampled Cr:Cb plane */
 
 /*
+ * 2 plane 10 bit per component YCbCr
+ * index 0 = Y plane, [31:0] x:Y2:Y1:Y0 2:10:10:10 little endian
+ * index 1 = Cb:Cr plane, [63:0] x:Cb2:Cr2:Cb1:x:Cr1:Cb0:Cr0 2:10:10:10:2:10:10:10 little endian
+ */
+#define DRM_FORMAT_XV15		fourcc_code('X', 'V', '1', '5') /* 2x2 subsampled Cb:Cr plane 2:10:10:10 */
+#define DRM_FORMAT_XV20		fourcc_code('X', 'V', '2', '0') /* 2x1 subsampled Cb:Cr plane 2:10:10:10 */
+
+/*
  * 2 plane YCbCr MSB aligned
  * index 0 = Y plane, [15:0] Y:x [10:6] little endian
  * index 1 = Cr:Cb plane, [31:0] Cr:x:Cb:x [10:6:10:6] little endian
@@ -308,6 +323,13 @@
  */
 #define DRM_FORMAT_P016		fourcc_code('P', '0', '1', '6') /* 2x2 subsampled Cr:Cb plane 16 bits per channel */
 
+/* 2 plane YCbCr420.
+ * 3 10 bit components and 2 padding bits packed into 4 bytes.
+ * index 0 = Y plane, [31:0] x:Y2:Y1:Y0 2:10:10:10 little endian
+ * index 1 = Cr:Cb plane, [63:0] x:Cr2:Cb2:Cr1:x:Cb1:Cr0:Cb0 [2:10:10:10:2:10:10:10] little endian
+ */
+#define DRM_FORMAT_P030		fourcc_code('P', '0', '3', '0') /* 2x2 subsampled Cr:Cb plane 10 bits per channel packed */
+
 /* 3 plane non-subsampled (444) YCbCr
  * 16 bits per component, but only 10 bits are used and 6 bits are padded
  * index 0: Y plane, [15:0] Y:x [10:6] little endian
@@ -324,6 +346,14 @@
  */
 #define DRM_FORMAT_Q401		fourcc_code('Q', '4', '0', '1')
 
+/* 3 plane non-subsampled (444) YCbCr
+ * 10 bpc, 30 bits per sample image data in a single contiguous buffer.
+ * index 0: Y plane, [31:0] x:Y2:Y1:Y0 [2:10:10:10] little endian
+ * index 1: Cb plane, [31:0] x:Cb2:Cb1:Cb0 [2:10:10:10] little endian
+ * index 2: Cr plane, [31:0] x:Cr2:Cr1:Cr0 [2:10:10:10] little endian
+ */
+#define DRM_FORMAT_X403		fourcc_code('X', '4', '0', '3') /* non-subsampled Cb:Cr plane, 10 bit per channel */
+
 /*
  * 3 plane YCbCr
  * index 0: Y plane, [7:0] Y
@@ -842,6 +872,10 @@
  * and UV.  Some SAND-using hardware stores UV in a separate tiled
  * image from Y to reduce the column height, which is not supported
  * with these modifiers.
+ *
+ * The DRM_FORMAT_MOD_BROADCOM_SAND128_COL_HEIGHT modifier is also
+ * supported for DRM_FORMAT_P030 where the columns remain as 128 bytes
+ * wide, but as this is a 10 bpp format that translates to 96 pixels.
  */
 
 #define DRM_FORMAT_MOD_BROADCOM_SAND32_COL_HEIGHT(v) \
@@ -1352,11 +1386,11 @@
 #define AMD_FMT_MOD_PIPE_MASK 0x7
 
 #define AMD_FMT_MOD_SET(field, value) \
-	((uint64_t)(value) << AMD_FMT_MOD_##field##_SHIFT)
+	((__u64)(value) << AMD_FMT_MOD_##field##_SHIFT)
 #define AMD_FMT_MOD_GET(field, value) \
 	(((value) >> AMD_FMT_MOD_##field##_SHIFT) & AMD_FMT_MOD_##field##_MASK)
 #define AMD_FMT_MOD_CLEAR(field) \
-	(~((uint64_t)AMD_FMT_MOD_##field##_MASK << AMD_FMT_MOD_##field##_SHIFT))
+	(~((__u64)AMD_FMT_MOD_##field##_MASK << AMD_FMT_MOD_##field##_SHIFT))
 
 #if defined(__cplusplus)
 }
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/drm/drm_mode.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/drm/drm_mode.h
@@ -662,6 +662,8 @@
 
 #define DRM_MODE_FB_INTERLACED	(1<<0) /* for interlaced framebuffers */
 #define DRM_MODE_FB_MODIFIERS	(1<<1) /* enables ->modifer[] */
+#define DRM_MODE_FB_ALTERNATE_TOP	(1<<2) /* for alternate top field */
+#define DRM_MODE_FB_ALTERNATE_BOTTOM	(1<<3) /* for alternate bottom field */
 
 struct drm_mode_fb_cmd2 {
 	__u32 fb_id;
@@ -817,6 +819,20 @@
 	__u16 reserved;
 };
 
+enum drm_hdr_type {
+	/*
+	 * This is for the gen_hdr_output_metadata structure.
+	 * MSB differentiates static (0) or dynamic (1) metadata.
+	 * Other 15 bits represent specific HDR standards.
+	 */
+
+	/* static HDR */
+	DRM_HDR_TYPE_HDR10     = 0x0000,
+
+	/* dynamic HDR */
+	DRM_HDR_TYPE_HDR10P    = 1 << 15 | DRM_HDR_TYPE_HDR10,
+};
+
 /**
  * struct hdr_metadata_infoframe - HDR Metadata Infoframe Data.
  *
@@ -903,6 +919,27 @@
 	};
 };
 
+/**
+ * struct gen_hdr_output_metadata - Generic HDR output metadata
+ *
+ * Generic HDR Metadata Information to be passed from userspace
+ */
+struct gen_hdr_output_metadata {
+	/**
+	 * @metadata_type: HDR type.
+	 */
+	__u16 metadata_type;
+	/**
+	 * @size: size of payload/metadata.
+	 */
+	__u16 size;
+	/**
+	 * @payload: Actual metadata - HDR Metadata Infoframe.
+	 * Currently the largest extended HDR infoframe is 4000 bytes.
+	 */
+	__u8 payload[4000];
+};
+
 #define DRM_MODE_PAGE_FLIP_EVENT 0x01
 #define DRM_MODE_PAGE_FLIP_ASYNC 0x02
 #define DRM_MODE_PAGE_FLIP_TARGET_ABSOLUTE 0x4
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/affs_hardblocks.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/affs_hardblocks.h
@@ -7,42 +7,42 @@
 /* Just the needed definitions for the RDB of an Amiga HD. */
 
 struct RigidDiskBlock {
-	__u32	rdb_ID;
+	__be32	rdb_ID;
 	__be32	rdb_SummedLongs;
-	__s32	rdb_ChkSum;
-	__u32	rdb_HostID;
+	__be32	rdb_ChkSum;
+	__be32	rdb_HostID;
 	__be32	rdb_BlockBytes;
-	__u32	rdb_Flags;
-	__u32	rdb_BadBlockList;
+	__be32	rdb_Flags;
+	__be32	rdb_BadBlockList;
 	__be32	rdb_PartitionList;
-	__u32	rdb_FileSysHeaderList;
-	__u32	rdb_DriveInit;
-	__u32	rdb_Reserved1[6];
-	__u32	rdb_Cylinders;
-	__u32	rdb_Sectors;
-	__u32	rdb_Heads;
-	__u32	rdb_Interleave;
-	__u32	rdb_Park;
-	__u32	rdb_Reserved2[3];
-	__u32	rdb_WritePreComp;
-	__u32	rdb_ReducedWrite;
-	__u32	rdb_StepRate;
-	__u32	rdb_Reserved3[5];
-	__u32	rdb_RDBBlocksLo;
-	__u32	rdb_RDBBlocksHi;
-	__u32	rdb_LoCylinder;
-	__u32	rdb_HiCylinder;
-	__u32	rdb_CylBlocks;
-	__u32	rdb_AutoParkSeconds;
-	__u32	rdb_HighRDSKBlock;
-	__u32	rdb_Reserved4;
+	__be32	rdb_FileSysHeaderList;
+	__be32	rdb_DriveInit;
+	__be32	rdb_Reserved1[6];
+	__be32	rdb_Cylinders;
+	__be32	rdb_Sectors;
+	__be32	rdb_Heads;
+	__be32	rdb_Interleave;
+	__be32	rdb_Park;
+	__be32	rdb_Reserved2[3];
+	__be32	rdb_WritePreComp;
+	__be32	rdb_ReducedWrite;
+	__be32	rdb_StepRate;
+	__be32	rdb_Reserved3[5];
+	__be32	rdb_RDBBlocksLo;
+	__be32	rdb_RDBBlocksHi;
+	__be32	rdb_LoCylinder;
+	__be32	rdb_HiCylinder;
+	__be32	rdb_CylBlocks;
+	__be32	rdb_AutoParkSeconds;
+	__be32	rdb_HighRDSKBlock;
+	__be32	rdb_Reserved4;
 	char	rdb_DiskVendor[8];
 	char	rdb_DiskProduct[16];
 	char	rdb_DiskRevision[4];
 	char	rdb_ControllerVendor[8];
 	char	rdb_ControllerProduct[16];
 	char	rdb_ControllerRevision[4];
-	__u32	rdb_Reserved5[10];
+	__be32	rdb_Reserved5[10];
 };
 
 #define	IDNAME_RIGIDDISK	0x5244534B	/* "RDSK" */
@@ -50,16 +50,16 @@
 struct PartitionBlock {
 	__be32	pb_ID;
 	__be32	pb_SummedLongs;
-	__s32	pb_ChkSum;
-	__u32	pb_HostID;
+	__be32	pb_ChkSum;
+	__be32	pb_HostID;
 	__be32	pb_Next;
-	__u32	pb_Flags;
-	__u32	pb_Reserved1[2];
-	__u32	pb_DevFlags;
+	__be32	pb_Flags;
+	__be32	pb_Reserved1[2];
+	__be32	pb_DevFlags;
 	__u8	pb_DriveName[32];
-	__u32	pb_Reserved2[15];
+	__be32	pb_Reserved2[15];
 	__be32	pb_Environment[17];
-	__u32	pb_EReserved[15];
+	__be32	pb_EReserved[15];
 };
 
 #define	IDNAME_PARTITION	0x50415254	/* "PART" */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/audit.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/audit.h
@@ -139,6 +139,8 @@
 #define AUDIT_MAC_UNLBL_STCDEL	1417	/* NetLabel: del a static label */
 #define AUDIT_MAC_CALIPSO_ADD	1418	/* NetLabel: add CALIPSO DOI entry */
 #define AUDIT_MAC_CALIPSO_DEL	1419	/* NetLabel: del CALIPSO DOI entry */
+#define AUDIT_MAC_TASK_CONTEXTS	1420	/* Multiple LSM contexts */
+#define AUDIT_MAC_OBJ_CONTEXTS	1421	/* Multiple LSM object contexts */
 
 #define AUDIT_FIRST_KERN_ANOM_MSG   1700
 #define AUDIT_LAST_KERN_ANOM_MSG    1799
@@ -182,7 +184,7 @@
 #define AUDIT_MAX_KEY_LEN  256
 #define AUDIT_BITMASK_SIZE 64
 #define AUDIT_WORD(nr) ((__u32)((nr)/32))
-#define AUDIT_BIT(nr)  (1 << ((nr) - AUDIT_WORD(nr)*32))
+#define AUDIT_BIT(nr)  (1U << ((nr) - AUDIT_WORD(nr)*32))
 
 #define AUDIT_SYSCALL_CLASSES 16
 #define AUDIT_CLASS_DIR_WRITE 0
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/aufs_type.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/aufs_type.h
@@ -0,0 +1,452 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Copyright (C) 2005-2021 Junjiro R. Okajima
+ *
+ * This program, aufs is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __AUFS_TYPE_H__
+#define __AUFS_TYPE_H__
+
+#define AUFS_NAME	"aufs"
+
+#ifdef __KERNEL__
+/*
+ * define it before including all other headers.
+ * sched.h may use pr_* macros before defining "current", so define the
+ * no-current version first, and re-define later.
+ */
+#define pr_fmt(fmt)	AUFS_NAME " %s:%d: " fmt, __func__, __LINE__
+#include <linux/sched.h>
+#undef pr_fmt
+#define pr_fmt(fmt) \
+		AUFS_NAME " %s:%d:%.*s[%d]: " fmt, __func__, __LINE__, \
+		(int)sizeof(current->comm), current->comm, current->pid
+#include <linux/limits.h>
+#else
+#include <stdint.h>
+#include <sys/types.h>
+#include <limits.h>
+#endif /* __KERNEL__ */
+
+#define AUFS_VERSION	"5.15.5-20211129"
+
+/* todo? move this to linux-2.6.19/include/magic.h */
+#define AUFS_SUPER_MAGIC	('a' << 24 | 'u' << 16 | 'f' << 8 | 's')
+
+/* ---------------------------------------------------------------------- */
+
+#ifdef __KERNEL__
+#ifdef CONFIG_AUFS_BRANCH_MAX_127
+typedef int8_t aufs_bindex_t;
+#define AUFS_BRANCH_MAX 127
+#else
+typedef int16_t aufs_bindex_t;
+#ifdef CONFIG_AUFS_BRANCH_MAX_511
+#define AUFS_BRANCH_MAX 511
+#elif defined(CONFIG_AUFS_BRANCH_MAX_1023)
+#define AUFS_BRANCH_MAX 1023
+#elif defined(CONFIG_AUFS_BRANCH_MAX_32767)
+#define AUFS_BRANCH_MAX 32767
+#endif
+#endif
+
+#ifndef AUFS_BRANCH_MAX
+#error unknown CONFIG_AUFS_BRANCH_MAX value
+#endif
+#endif /* __KERNEL__ */
+
+/* ---------------------------------------------------------------------- */
+
+#define AUFS_FSTYPE		AUFS_NAME
+
+#define AUFS_ROOT_INO		2
+#define AUFS_FIRST_INO		11
+
+#define AUFS_WH_PFX		".wh."
+#define AUFS_WH_PFX_LEN		((int)sizeof(AUFS_WH_PFX) - 1)
+#define AUFS_WH_TMP_LEN		4
+/* a limit for rmdir/rename a dir and copyup */
+#define AUFS_MAX_NAMELEN	(NAME_MAX \
+				- AUFS_WH_PFX_LEN * 2	/* doubly whiteouted */\
+				- 1			/* dot */\
+				- AUFS_WH_TMP_LEN)	/* hex */
+#define AUFS_XINO_FNAME		"." AUFS_NAME ".xino"
+#define AUFS_XINO_DEFPATH	"/tmp/" AUFS_XINO_FNAME
+#define AUFS_XINO_DEF_SEC	30 /* seconds */
+#define AUFS_XINO_DEF_TRUNC	45 /* percentage */
+#define AUFS_DIRWH_DEF		3
+#define AUFS_RDCACHE_DEF	10 /* seconds */
+#define AUFS_RDCACHE_MAX	3600 /* seconds */
+#define AUFS_RDBLK_DEF		512 /* bytes */
+#define AUFS_RDHASH_DEF		32
+#define AUFS_WKQ_NAME		AUFS_NAME "d"
+#define AUFS_MFS_DEF_SEC	30 /* seconds */
+#define AUFS_MFS_MAX_SEC	3600 /* seconds */
+#define AUFS_FHSM_CACHE_DEF_SEC	30 /* seconds */
+#define AUFS_PLINK_WARN		50 /* number of plinks in a single bucket */
+
+/* pseudo-link maintenace under /proc */
+#define AUFS_PLINK_MAINT_NAME	"plink_maint"
+#define AUFS_PLINK_MAINT_DIR	"fs/" AUFS_NAME
+#define AUFS_PLINK_MAINT_PATH	AUFS_PLINK_MAINT_DIR "/" AUFS_PLINK_MAINT_NAME
+
+/* dirren, renamed dir */
+#define AUFS_DR_INFO_PFX	AUFS_WH_PFX ".dr."
+#define AUFS_DR_BRHINO_NAME	AUFS_WH_PFX "hino"
+/* whiteouted doubly */
+#define AUFS_WH_DR_INFO_PFX	AUFS_WH_PFX AUFS_DR_INFO_PFX
+#define AUFS_WH_DR_BRHINO	AUFS_WH_PFX AUFS_DR_BRHINO_NAME
+
+#define AUFS_DIROPQ_NAME	AUFS_WH_PFX ".opq" /* whiteouted doubly */
+#define AUFS_WH_DIROPQ		AUFS_WH_PFX AUFS_DIROPQ_NAME
+
+#define AUFS_BASE_NAME		AUFS_WH_PFX AUFS_NAME
+#define AUFS_PLINKDIR_NAME	AUFS_WH_PFX "plnk"
+#define AUFS_ORPHDIR_NAME	AUFS_WH_PFX "orph"
+
+/* doubly whiteouted */
+#define AUFS_WH_BASE		AUFS_WH_PFX AUFS_BASE_NAME
+#define AUFS_WH_PLINKDIR	AUFS_WH_PFX AUFS_PLINKDIR_NAME
+#define AUFS_WH_ORPHDIR		AUFS_WH_PFX AUFS_ORPHDIR_NAME
+
+/* branch permissions and attributes */
+#define AUFS_BRPERM_RW		"rw"
+#define AUFS_BRPERM_RO		"ro"
+#define AUFS_BRPERM_RR		"rr"
+#define AUFS_BRATTR_COO_REG	"coo_reg"
+#define AUFS_BRATTR_COO_ALL	"coo_all"
+#define AUFS_BRATTR_FHSM	"fhsm"
+#define AUFS_BRATTR_UNPIN	"unpin"
+#define AUFS_BRATTR_ICEX	"icex"
+#define AUFS_BRATTR_ICEX_SEC	"icexsec"
+#define AUFS_BRATTR_ICEX_SYS	"icexsys"
+#define AUFS_BRATTR_ICEX_TR	"icextr"
+#define AUFS_BRATTR_ICEX_USR	"icexusr"
+#define AUFS_BRATTR_ICEX_OTH	"icexoth"
+#define AUFS_BRRATTR_WH		"wh"
+#define AUFS_BRWATTR_NLWH	"nolwh"
+#define AUFS_BRWATTR_MOO	"moo"
+
+#define AuBrPerm_RW		1		/* writable, hardlinkable wh */
+#define AuBrPerm_RO		(1 << 1)	/* readonly */
+#define AuBrPerm_RR		(1 << 2)	/* natively readonly */
+#define AuBrPerm_Mask		(AuBrPerm_RW | AuBrPerm_RO | AuBrPerm_RR)
+
+#define AuBrAttr_COO_REG	(1 << 3)	/* copy-up on open */
+#define AuBrAttr_COO_ALL	(1 << 4)
+#define AuBrAttr_COO_Mask	(AuBrAttr_COO_REG | AuBrAttr_COO_ALL)
+
+#define AuBrAttr_FHSM		(1 << 5)	/* file-based hsm */
+#define AuBrAttr_UNPIN		(1 << 6)	/* rename-able top dir of
+						   branch. meaningless since
+						   linux-3.18-rc1 */
+
+/* ignore error in copying XATTR */
+#define AuBrAttr_ICEX_SEC	(1 << 7)
+#define AuBrAttr_ICEX_SYS	(1 << 8)
+#define AuBrAttr_ICEX_TR	(1 << 9)
+#define AuBrAttr_ICEX_USR	(1 << 10)
+#define AuBrAttr_ICEX_OTH	(1 << 11)
+#define AuBrAttr_ICEX		(AuBrAttr_ICEX_SEC	\
+				 | AuBrAttr_ICEX_SYS	\
+				 | AuBrAttr_ICEX_TR	\
+				 | AuBrAttr_ICEX_USR	\
+				 | AuBrAttr_ICEX_OTH)
+
+#define AuBrRAttr_WH		(1 << 12)	/* whiteout-able */
+#define AuBrRAttr_Mask		AuBrRAttr_WH
+
+#define AuBrWAttr_NoLinkWH	(1 << 13)	/* un-hardlinkable whiteouts */
+#define AuBrWAttr_MOO		(1 << 14)	/* move-up on open */
+#define AuBrWAttr_Mask		(AuBrWAttr_NoLinkWH | AuBrWAttr_MOO)
+
+#define AuBrAttr_CMOO_Mask	(AuBrAttr_COO_Mask | AuBrWAttr_MOO)
+
+/* #warning test userspace */
+#ifdef __KERNEL__
+#ifndef CONFIG_AUFS_FHSM
+#undef AuBrAttr_FHSM
+#define AuBrAttr_FHSM		0
+#endif
+#ifndef CONFIG_AUFS_XATTR
+#undef	AuBrAttr_ICEX
+#define AuBrAttr_ICEX		0
+#undef	AuBrAttr_ICEX_SEC
+#define AuBrAttr_ICEX_SEC	0
+#undef	AuBrAttr_ICEX_SYS
+#define AuBrAttr_ICEX_SYS	0
+#undef	AuBrAttr_ICEX_TR
+#define AuBrAttr_ICEX_TR	0
+#undef	AuBrAttr_ICEX_USR
+#define AuBrAttr_ICEX_USR	0
+#undef	AuBrAttr_ICEX_OTH
+#define AuBrAttr_ICEX_OTH	0
+#endif
+#endif
+
+/* the longest combination */
+/* AUFS_BRATTR_ICEX and AUFS_BRATTR_ICEX_TR don't affect here */
+#define AuBrPermStrSz	sizeof(AUFS_BRPERM_RW			\
+			       "+" AUFS_BRATTR_COO_REG		\
+			       "+" AUFS_BRATTR_FHSM		\
+			       "+" AUFS_BRATTR_UNPIN		\
+			       "+" AUFS_BRATTR_ICEX_SEC		\
+			       "+" AUFS_BRATTR_ICEX_SYS		\
+			       "+" AUFS_BRATTR_ICEX_USR		\
+			       "+" AUFS_BRATTR_ICEX_OTH		\
+			       "+" AUFS_BRWATTR_NLWH)
+
+typedef struct {
+	char a[AuBrPermStrSz];
+} au_br_perm_str_t;
+
+static inline int au_br_writable(int brperm)
+{
+	return brperm & AuBrPerm_RW;
+}
+
+static inline int au_br_whable(int brperm)
+{
+	return brperm & (AuBrPerm_RW | AuBrRAttr_WH);
+}
+
+static inline int au_br_wh_linkable(int brperm)
+{
+	return !(brperm & AuBrWAttr_NoLinkWH);
+}
+
+static inline int au_br_cmoo(int brperm)
+{
+	return brperm & AuBrAttr_CMOO_Mask;
+}
+
+static inline int au_br_fhsm(int brperm)
+{
+	return brperm & AuBrAttr_FHSM;
+}
+
+/* ---------------------------------------------------------------------- */
+
+/* ioctl */
+enum {
+	/* readdir in userspace */
+	AuCtl_RDU,
+	AuCtl_RDU_INO,
+
+	AuCtl_WBR_FD,	/* pathconf wrapper */
+	AuCtl_IBUSY,	/* busy inode */
+	AuCtl_MVDOWN,	/* move-down */
+	AuCtl_BR,	/* info about branches */
+	AuCtl_FHSM_FD	/* connection for fhsm */
+};
+
+/* borrowed from linux/include/linux/kernel.h */
+#ifndef ALIGN
+#ifdef _GNU_SOURCE
+#define ALIGN(x, a)		__ALIGN_MASK(x, (typeof(x))(a)-1)
+#else
+#define ALIGN(x, a)		(((x) + (a) - 1) & ~((a) - 1))
+#endif
+#define __ALIGN_MASK(x, mask)	(((x)+(mask))&~(mask))
+#endif
+
+/* borrowed from linux/include/linux/compiler-gcc3.h */
+#ifndef __aligned
+#define __aligned(x)			__attribute__((aligned(x)))
+#endif
+
+#ifdef __KERNEL__
+#ifndef __packed
+#define __packed			__attribute__((packed))
+#endif
+#endif
+
+struct au_rdu_cookie {
+	uint64_t	h_pos;
+	int16_t		bindex;
+	uint8_t		flags;
+	uint8_t		pad;
+	uint32_t	generation;
+} __aligned(8);
+
+struct au_rdu_ent {
+	uint64_t	ino;
+	int16_t		bindex;
+	uint8_t		type;
+	uint8_t		nlen;
+	uint8_t		wh;
+	char		name[];
+} __aligned(8);
+
+static inline int au_rdu_len(int nlen)
+{
+	/* include the terminating NULL */
+	return ALIGN(sizeof(struct au_rdu_ent) + nlen + 1,
+		     sizeof(uint64_t));
+}
+
+union au_rdu_ent_ul {
+	struct au_rdu_ent __user	*e;
+	uint64_t			ul;
+};
+
+enum {
+	AufsCtlRduV_SZ,
+	AufsCtlRduV_End
+};
+
+struct aufs_rdu {
+	/* input */
+	union {
+		uint64_t	sz;	/* AuCtl_RDU */
+		uint64_t	nent;	/* AuCtl_RDU_INO */
+	};
+	union au_rdu_ent_ul	ent;
+	uint16_t		verify[AufsCtlRduV_End];
+
+	/* input/output */
+	uint32_t		blk;
+
+	/* output */
+	union au_rdu_ent_ul	tail;
+	/* number of entries which were added in a single call */
+	uint64_t		rent;
+	uint8_t			full;
+	uint8_t			shwh;
+
+	struct au_rdu_cookie	cookie;
+} __aligned(8);
+
+/* ---------------------------------------------------------------------- */
+
+/* dirren. the branch is identified by the filename who contains this */
+struct au_drinfo {
+	uint64_t ino;
+	union {
+		uint8_t oldnamelen;
+		uint64_t _padding;
+	};
+	uint8_t oldname[];
+} __aligned(8);
+
+struct au_drinfo_fdata {
+	uint32_t magic;
+	struct au_drinfo drinfo;
+} __aligned(8);
+
+#define AUFS_DRINFO_MAGIC_V1	('a' << 24 | 'd' << 16 | 'r' << 8 | 0x01)
+/* future */
+#define AUFS_DRINFO_MAGIC_V2	('a' << 24 | 'd' << 16 | 'r' << 8 | 0x02)
+
+/* ---------------------------------------------------------------------- */
+
+struct aufs_wbr_fd {
+	uint32_t	oflags;
+	int16_t		brid;
+} __aligned(8);
+
+/* ---------------------------------------------------------------------- */
+
+struct aufs_ibusy {
+	uint64_t	ino, h_ino;
+	int16_t		bindex;
+} __aligned(8);
+
+/* ---------------------------------------------------------------------- */
+
+/* error code for move-down */
+/* the actual message strings are implemented in aufs-util.git */
+enum {
+	EAU_MVDOWN_OPAQUE = 1,
+	EAU_MVDOWN_WHITEOUT,
+	EAU_MVDOWN_UPPER,
+	EAU_MVDOWN_BOTTOM,
+	EAU_MVDOWN_NOUPPER,
+	EAU_MVDOWN_NOLOWERBR,
+	EAU_Last
+};
+
+/* flags for move-down */
+#define AUFS_MVDOWN_DMSG	1
+#define AUFS_MVDOWN_OWLOWER	(1 << 1)	/* overwrite lower */
+#define AUFS_MVDOWN_KUPPER	(1 << 2)	/* keep upper */
+#define AUFS_MVDOWN_ROLOWER	(1 << 3)	/* do even if lower is RO */
+#define AUFS_MVDOWN_ROLOWER_R	(1 << 4)	/* did on lower RO */
+#define AUFS_MVDOWN_ROUPPER	(1 << 5)	/* do even if upper is RO */
+#define AUFS_MVDOWN_ROUPPER_R	(1 << 6)	/* did on upper RO */
+#define AUFS_MVDOWN_BRID_UPPER	(1 << 7)	/* upper brid */
+#define AUFS_MVDOWN_BRID_LOWER	(1 << 8)	/* lower brid */
+#define AUFS_MVDOWN_FHSM_LOWER	(1 << 9)	/* find fhsm attr for lower */
+#define AUFS_MVDOWN_STFS	(1 << 10)	/* req. stfs */
+#define AUFS_MVDOWN_STFS_FAILED	(1 << 11)	/* output: stfs is unusable */
+#define AUFS_MVDOWN_BOTTOM	(1 << 12)	/* output: no more lowers */
+
+/* index for move-down */
+enum {
+	AUFS_MVDOWN_UPPER,
+	AUFS_MVDOWN_LOWER,
+	AUFS_MVDOWN_NARRAY
+};
+
+/*
+ * additional info of move-down
+ * number of free blocks and inodes.
+ * subset of struct kstatfs, but smaller and always 64bit.
+ */
+struct aufs_stfs {
+	uint64_t	f_blocks;
+	uint64_t	f_bavail;
+	uint64_t	f_files;
+	uint64_t	f_ffree;
+};
+
+struct aufs_stbr {
+	int16_t			brid;	/* optional input */
+	int16_t			bindex;	/* output */
+	struct aufs_stfs	stfs;	/* output when AUFS_MVDOWN_STFS set */
+} __aligned(8);
+
+struct aufs_mvdown {
+	uint32_t		flags;			/* input/output */
+	struct aufs_stbr	stbr[AUFS_MVDOWN_NARRAY]; /* input/output */
+	int8_t			au_errno;		/* output */
+} __aligned(8);
+
+/* ---------------------------------------------------------------------- */
+
+union aufs_brinfo {
+	/* PATH_MAX may differ between kernel-space and user-space */
+	char	_spacer[4096];
+	struct {
+		int16_t	id;
+		int	perm;
+		char	path[];
+	};
+} __aligned(8);
+
+/* ---------------------------------------------------------------------- */
+
+#define AuCtlType		'A'
+#define AUFS_CTL_RDU		_IOWR(AuCtlType, AuCtl_RDU, struct aufs_rdu)
+#define AUFS_CTL_RDU_INO	_IOWR(AuCtlType, AuCtl_RDU_INO, struct aufs_rdu)
+#define AUFS_CTL_WBR_FD		_IOW(AuCtlType, AuCtl_WBR_FD, \
+				     struct aufs_wbr_fd)
+#define AUFS_CTL_IBUSY		_IOWR(AuCtlType, AuCtl_IBUSY, struct aufs_ibusy)
+#define AUFS_CTL_MVDOWN		_IOWR(AuCtlType, AuCtl_MVDOWN, \
+				      struct aufs_mvdown)
+#define AUFS_CTL_BRINFO		_IOW(AuCtlType, AuCtl_BR, union aufs_brinfo)
+#define AUFS_CTL_FHSM_FD	_IOW(AuCtlType, AuCtl_FHSM_FD, int)
+
+#endif /* __AUFS_TYPE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/auto_dev-ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/auto_dev-ioctl.h
@@ -109,7 +109,7 @@
 		struct args_ismountpoint	ismountpoint;
 	};
 
-	char path[0];
+	char path[];
 };
 
 static inline void init_autofs_dev_ioctl(struct autofs_dev_ioctl *in)
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/blkzoned.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/blkzoned.h
@@ -51,13 +51,13 @@
  *
  * The Zone Condition state machine in the ZBC/ZAC standards maps the above
  * deinitions as:
- *   - ZC1: Empty         | BLK_ZONE_EMPTY
+ *   - ZC1: Empty         | BLK_ZONE_COND_EMPTY
  *   - ZC2: Implicit Open | BLK_ZONE_COND_IMP_OPEN
  *   - ZC3: Explicit Open | BLK_ZONE_COND_EXP_OPEN
- *   - ZC4: Closed        | BLK_ZONE_CLOSED
- *   - ZC5: Full          | BLK_ZONE_FULL
- *   - ZC6: Read Only     | BLK_ZONE_READONLY
- *   - ZC7: Offline       | BLK_ZONE_OFFLINE
+ *   - ZC4: Closed        | BLK_ZONE_COND_CLOSED
+ *   - ZC5: Full          | BLK_ZONE_COND_FULL
+ *   - ZC6: Read Only     | BLK_ZONE_COND_READONLY
+ *   - ZC7: Offline       | BLK_ZONE_COND_OFFLINE
  *
  * Conditions 0x5 to 0xC are reserved by the current ZBC/ZAC spec and should
  * be considered invalid.
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/bpf.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/bpf.h
@@ -1762,7 +1762,9 @@
  * 		performed again, if the helper is used in combination with
  * 		direct packet access.
  * 	Return
- * 		0 on success, or a negative error in case of failure.
+ * 		0 on success, or a negative error in case of failure. Positive
+ * 		error indicates a potential drop or congestion in the target
+ * 		device. The particular positive error codes are not defined.
  *
  * u64 bpf_get_current_pid_tgid(void)
  * 	Return
@@ -2276,8 +2278,8 @@
  * 	Return
  * 		The return value depends on the result of the test, and can be:
  *
- *		* 0, if current task belongs to the cgroup2.
- *		* 1, if current task does not belong to the cgroup2.
+ *		* 1, if current task belongs to the cgroup2.
+ *		* 0, if current task does not belong to the cgroup2.
  * 		* A negative error code, if an error occurred.
  *
  * long bpf_skb_change_tail(struct sk_buff *skb, u32 len, u64 flags)
@@ -2965,8 +2967,8 @@
  *
  * 			# sysctl kernel.perf_event_max_stack=<new value>
  * 	Return
- * 		A non-negative value equal to or less than *size* on success,
- * 		or a negative error in case of failure.
+ * 		The non-negative copied *buf* length equal to or less than
+ * 		*size* on success, or a negative error in case of failure.
  *
  * long bpf_skb_load_bytes_relative(const void *skb, u32 offset, void *to, u32 len, u32 start_header)
  * 	Description
@@ -3009,9 +3011,23 @@
  *		**BPF_FIB_LOOKUP_DIRECT**
  *			Do a direct table lookup vs full lookup using FIB
  *			rules.
+ *		**BPF_FIB_LOOKUP_TBID**
+ *			Used with BPF_FIB_LOOKUP_DIRECT.
+ *			Use the routing table ID present in *params*->tbid
+ *			for the fib lookup.
  *		**BPF_FIB_LOOKUP_OUTPUT**
  *			Perform lookup from an egress perspective (default is
  *			ingress).
+ *		**BPF_FIB_LOOKUP_SKIP_NEIGH**
+ *			Skip the neighbour table lookup. *params*->dmac
+ *			and *params*->smac will not be set as output. A common
+ *			use case is to call **bpf_redirect_neigh**\ () after
+ *			doing **bpf_fib_lookup**\ ().
+ *		**BPF_FIB_LOOKUP_SRC**
+ *			Derive and set source IP addr in *params*->ipv{4,6}_src
+ *			for the nexthop. If the src addr cannot be derived,
+ *			**BPF_FIB_LKUP_RET_NO_SRC_ADDR** is returned. In this
+ *			case, *params*->dmac and *params*->smac are not set either.
  *
  *		*ctx* is either **struct xdp_md** for XDP programs or
  *		**struct sk_buff** tc cls_act programs.
@@ -4243,6 +4259,8 @@
  * long bpf_get_task_stack(struct task_struct *task, void *buf, u32 size, u64 flags)
  *	Description
  *		Return a user or a kernel stack in bpf program provided buffer.
+ *		Note: the user stack will only be populated if the *task* is
+ *		the current task; all other tasks will return -EOPNOTSUPP.
  *		To achieve this, the helper needs *task*, which is a valid
  *		pointer to **struct task_struct**. To store the stacktrace, the
  *		bpf program provides *buf* with a nonnegative *size*.
@@ -4254,6 +4272,7 @@
  *
  *		**BPF_F_USER_STACK**
  *			Collect a user space stack instead of a kernel stack.
+ *			The *task* must be the current task.
  *		**BPF_F_USER_BUILD_ID**
  *			Collect buildid+offset instead of ips for user stack,
  *			only valid if **BPF_F_USER_STACK** is also specified.
@@ -4269,8 +4288,8 @@
  *
  *			# sysctl kernel.perf_event_max_stack=<new value>
  *	Return
- *		A non-negative value equal to or less than *size* on success,
- *		or a negative error in case of failure.
+ * 		The non-negative copied *buf* length equal to or less than
+ * 		*size* on success, or a negative error in case of failure.
  *
  * long bpf_load_hdr_opt(struct bpf_sock_ops *skops, void *searchby_res, u32 len, u64 flags)
  *	Description
@@ -5089,11 +5108,6 @@
 	BPF_F_MARK_ENFORCE		= (1ULL << 6),
 };
 
-/* BPF_FUNC_clone_redirect and BPF_FUNC_redirect flags. */
-enum {
-	BPF_F_INGRESS			= (1ULL << 0),
-};
-
 /* BPF_FUNC_skb_set_tunnel_key and BPF_FUNC_skb_get_tunnel_key flags. */
 enum {
 	BPF_F_TUNINFO_IPV6		= (1ULL << 0),
@@ -5232,10 +5246,12 @@
 	BPF_F_BPRM_SECUREEXEC	= (1ULL << 0),
 };
 
-/* Flags for bpf_redirect_map helper */
+/* Flags for bpf_redirect and bpf_redirect_map helpers */
 enum {
-	BPF_F_BROADCAST		= (1ULL << 3),
-	BPF_F_EXCLUDE_INGRESS	= (1ULL << 4),
+	BPF_F_INGRESS		= (1ULL << 0), /* used for skb path */
+	BPF_F_BROADCAST		= (1ULL << 3), /* used for XDP path */
+	BPF_F_EXCLUDE_INGRESS	= (1ULL << 4), /* used for XDP path */
+#define BPF_F_REDIRECT_FLAGS (BPF_F_INGRESS | BPF_F_BROADCAST | BPF_F_EXCLUDE_INGRESS)
 };
 
 #define __bpf_md_ptr(type, name)	\
@@ -5347,7 +5363,8 @@
 	__u32 src_ip4;
 	__u32 src_ip6[4];
 	__u32 src_port;		/* host byte order */
-	__u32 dst_port;		/* network byte order */
+	__be16 dst_port;	/* network byte order */
+	__u16 :16;		/* zero padding */
 	__u32 dst_ip4;
 	__u32 dst_ip6[4];
 	__u32 state;
@@ -6034,6 +6051,9 @@
 enum {
 	BPF_FIB_LOOKUP_DIRECT  = (1U << 0),
 	BPF_FIB_LOOKUP_OUTPUT  = (1U << 1),
+	BPF_FIB_LOOKUP_SKIP_NEIGH = (1U << 2),
+	BPF_FIB_LOOKUP_TBID    = (1U << 3),
+	BPF_FIB_LOOKUP_SRC     = (1U << 4),
 };
 
 enum {
@@ -6046,6 +6066,7 @@
 	BPF_FIB_LKUP_RET_UNSUPP_LWT,   /* fwd requires encapsulation */
 	BPF_FIB_LKUP_RET_NO_NEIGH,     /* no neighbor entry for nh */
 	BPF_FIB_LKUP_RET_FRAG_NEEDED,  /* fragmentation required to fwd */
+	BPF_FIB_LKUP_RET_NO_SRC_ADDR,  /* failed to derive IP src addr */
 };
 
 struct bpf_fib_lookup {
@@ -6065,7 +6086,7 @@
 
 		/* output: MTU value */
 		__u16	mtu_result;
-	};
+	} __attribute__((packed, aligned(2)));
 	/* input: L3 device index for lookup
 	 * output: device index from FIB lookup
 	 */
@@ -6080,6 +6101,9 @@
 		__u32	rt_metric;
 	};
 
+	/* input: source address to consider for lookup
+	 * output: source address result from lookup
+	 */
 	union {
 		__be32		ipv4_src;
 		__u32		ipv6_src[4];  /* in6_addr; network order */
@@ -6094,9 +6118,19 @@
 		__u32		ipv6_dst[4];  /* in6_addr; network order */
 	};
 
-	/* output */
-	__be16	h_vlan_proto;
-	__be16	h_vlan_TCI;
+	union {
+		struct {
+			/* output */
+			__be16	h_vlan_proto;
+			__be16	h_vlan_TCI;
+		};
+		/* input: when accompanied with the
+		 * 'BPF_FIB_LOOKUP_DIRECT | BPF_FIB_LOOKUP_TBID` flags, a
+		 * specific routing table to use for the fib lookup.
+		 */
+		__u32	tbid;
+	};
+
 	__u8	smac[6];     /* ETH_ALEN */
 	__u8	dmac[6];     /* ETH_ALEN */
 };
@@ -6222,7 +6256,8 @@
 	__u32 protocol;		/* IP protocol (IPPROTO_TCP, IPPROTO_UDP) */
 	__u32 remote_ip4;	/* Network byte order */
 	__u32 remote_ip6[4];	/* Network byte order */
-	__u32 remote_port;	/* Network byte order */
+	__be16 remote_port;	/* Network byte order */
+	__u16 :16;		/* Zero padding */
 	__u32 local_ip4;	/* Network byte order */
 	__u32 local_ip6[4];	/* Network byte order */
 	__u32 local_port;	/* Host byte order */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/btrfs.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/btrfs.h
@@ -181,6 +181,7 @@
 };
 
 #define BTRFS_SCRUB_READONLY	1
+#define BTRFS_SCRUB_SUPPORTED_FLAGS	(BTRFS_SCRUB_READONLY)
 struct btrfs_ioctl_scrub_args {
 	__u64 devid;				/* in */
 	__u64 start;				/* in */
@@ -309,6 +310,7 @@
 #define BTRFS_FEATURE_INCOMPAT_METADATA_UUID	(1ULL << 10)
 #define BTRFS_FEATURE_INCOMPAT_RAID1C34		(1ULL << 11)
 #define BTRFS_FEATURE_INCOMPAT_ZONED		(1ULL << 12)
+#define BTRFS_FEATURE_INCOMPAT_EXTENT_TREE_V2	(1ULL << 13)
 
 struct btrfs_ioctl_feature_flags {
 	__u64 compat_flags;
@@ -577,6 +579,9 @@
  */
 #define BTRFS_DEFRAG_RANGE_COMPRESS 1
 #define BTRFS_DEFRAG_RANGE_START_IO 2
+#define BTRFS_DEFRAG_RANGE_FLAGS_SUPP	(BTRFS_DEFRAG_RANGE_COMPRESS |		\
+					 BTRFS_DEFRAG_RANGE_START_IO)
+
 struct btrfs_ioctl_defrag_range_args {
 	/* start of the defrag operation */
 	__u64 start;
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/btrfs_tree.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/btrfs_tree.h
@@ -146,7 +146,9 @@
 
 /*
  * dir items are the name -> inode pointers in a directory.  There is one
- * for every name in a directory.
+ * for every name in a directory.  BTRFS_DIR_LOG_ITEM_KEY is no longer used
+ * but it's still defined here for documentation purposes and to help avoid
+ * having its numerical value reused in the future.
  */
 #define BTRFS_DIR_LOG_ITEM_KEY  60
 #define BTRFS_DIR_LOG_INDEX_KEY 72
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/byteorder/big_endian.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/byteorder/big_endian.h
@@ -9,6 +9,7 @@
 #define __BIG_ENDIAN_BITFIELD
 #endif
 
+#include <linux/stddef.h>
 #include <linux/types.h>
 #include <linux/swab.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/byteorder/little_endian.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/byteorder/little_endian.h
@@ -9,6 +9,7 @@
 #define __LITTLE_ENDIAN_BITFIELD
 #endif
 
+#include <linux/stddef.h>
 #include <linux/types.h>
 #include <linux/swab.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/can/error.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/can/error.h
@@ -120,6 +120,9 @@
 #define CAN_ERR_TRX_CANL_SHORT_TO_GND  0x70 /* 0111 0000 */
 #define CAN_ERR_TRX_CANL_SHORT_TO_CANH 0x80 /* 1000 0000 */
 
-/* controller specific additional information / data[5..7] */
+/* data[5] is reserved (do not use) */
+
+/* TX error counter / data[6] */
+/* RX error counter / data[7] */
 
 #endif /* _UAPI_CAN_ERROR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/can/isotp.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/can/isotp.h
@@ -124,33 +124,30 @@
 
 /* flags for isotp behaviour */
 
-#define CAN_ISOTP_LISTEN_MODE	0x001	/* listen only (do not send FC) */
-#define CAN_ISOTP_EXTEND_ADDR	0x002	/* enable extended addressing */
-#define CAN_ISOTP_TX_PADDING	0x004	/* enable CAN frame padding tx path */
-#define CAN_ISOTP_RX_PADDING	0x008	/* enable CAN frame padding rx path */
-#define CAN_ISOTP_CHK_PAD_LEN	0x010	/* check received CAN frame padding */
-#define CAN_ISOTP_CHK_PAD_DATA	0x020	/* check received CAN frame padding */
-#define CAN_ISOTP_HALF_DUPLEX	0x040	/* half duplex error state handling */
-#define CAN_ISOTP_FORCE_TXSTMIN	0x080	/* ignore stmin from received FC */
-#define CAN_ISOTP_FORCE_RXSTMIN	0x100	/* ignore CFs depending on rx stmin */
-#define CAN_ISOTP_RX_EXT_ADDR	0x200	/* different rx extended addressing */
-#define CAN_ISOTP_WAIT_TX_DONE	0x400	/* wait for tx completion */
-#define CAN_ISOTP_SF_BROADCAST	0x800	/* 1-to-N functional addressing */
+#define CAN_ISOTP_LISTEN_MODE	0x0001	/* listen only (do not send FC) */
+#define CAN_ISOTP_EXTEND_ADDR	0x0002	/* enable extended addressing */
+#define CAN_ISOTP_TX_PADDING	0x0004	/* enable CAN frame padding tx path */
+#define CAN_ISOTP_RX_PADDING	0x0008	/* enable CAN frame padding rx path */
+#define CAN_ISOTP_CHK_PAD_LEN	0x0010	/* check received CAN frame padding */
+#define CAN_ISOTP_CHK_PAD_DATA	0x0020	/* check received CAN frame padding */
+#define CAN_ISOTP_HALF_DUPLEX	0x0040	/* half duplex error state handling */
+#define CAN_ISOTP_FORCE_TXSTMIN	0x0080	/* ignore stmin from received FC */
+#define CAN_ISOTP_FORCE_RXSTMIN	0x0100	/* ignore CFs depending on rx stmin */
+#define CAN_ISOTP_RX_EXT_ADDR	0x0200	/* different rx extended addressing */
+#define CAN_ISOTP_WAIT_TX_DONE	0x0400	/* wait for tx completion */
+#define CAN_ISOTP_SF_BROADCAST	0x0800	/* 1-to-N functional addressing */
+#define CAN_ISOTP_CF_BROADCAST	0x1000	/* 1-to-N transmission w/o FC */
 
-/* default values */
+/* protocol machine default values */
 
 #define CAN_ISOTP_DEFAULT_FLAGS		0
 #define CAN_ISOTP_DEFAULT_EXT_ADDRESS	0x00
 #define CAN_ISOTP_DEFAULT_PAD_CONTENT	0xCC /* prevent bit-stuffing */
-#define CAN_ISOTP_DEFAULT_FRAME_TXTIME	0
+#define CAN_ISOTP_DEFAULT_FRAME_TXTIME	50000 /* 50 micro seconds */
 #define CAN_ISOTP_DEFAULT_RECV_BS	0
 #define CAN_ISOTP_DEFAULT_RECV_STMIN	0x00
 #define CAN_ISOTP_DEFAULT_RECV_WFTMAX	0
 
-#define CAN_ISOTP_DEFAULT_LL_MTU	CAN_MTU
-#define CAN_ISOTP_DEFAULT_LL_TX_DL	CAN_MAX_DLEN
-#define CAN_ISOTP_DEFAULT_LL_TX_FLAGS	0
-
 /*
  * Remark on CAN_ISOTP_DEFAULT_RECV_* values:
  *
@@ -162,4 +159,24 @@
  * consistency and copied directly into the flow control (FC) frame.
  */
 
+/* link layer default values => make use of Classical CAN frames */
+
+#define CAN_ISOTP_DEFAULT_LL_MTU	CAN_MTU
+#define CAN_ISOTP_DEFAULT_LL_TX_DL	CAN_MAX_DLEN
+#define CAN_ISOTP_DEFAULT_LL_TX_FLAGS	0
+
+/*
+ * The CAN_ISOTP_DEFAULT_FRAME_TXTIME has become a non-zero value as
+ * it only makes sense for isotp implementation tests to run without
+ * a N_As value. As user space applications usually do not set the
+ * frame_txtime element of struct can_isotp_options the new in-kernel
+ * default is very likely overwritten with zero when the sockopt()
+ * CAN_ISOTP_OPTS is invoked.
+ * To make sure that a N_As value of zero is only set intentional the
+ * value '0' is now interpreted as 'do not change the current value'.
+ * When a frame_txtime of zero is required for testing purposes this
+ * CAN_ISOTP_FRAME_TXTIME_ZERO u32 value has to be set in frame_txtime.
+ */
+#define CAN_ISOTP_FRAME_TXTIME_ZERO	0xFFFFFFFF
+
 #endif /* !_UAPI_CAN_ISOTP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/capability.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/capability.h
@@ -426,7 +426,7 @@
  */
 
 #define CAP_TO_INDEX(x)     ((x) >> 5)        /* 1 << 5 == bits in __u32 */
-#define CAP_TO_MASK(x)      (1 << ((x) & 31)) /* mask for indexed __u32 */
+#define CAP_TO_MASK(x)      (1U << ((x) & 31)) /* mask for indexed __u32 */
 
 
 #endif /* _UAPI_LINUX_CAPABILITY_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/cec.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/cec.h
@@ -132,6 +132,8 @@
  * Set the msg destination to the orig initiator and the msg initiator to the
  * orig destination. Note that msg and orig may be the same pointer, in which
  * case the change is done in place.
+ *
+ * It also zeroes the reply, timeout and flags fields.
  */
 static inline void cec_msg_set_reply_to(struct cec_msg *msg,
 					struct cec_msg *orig)
@@ -139,7 +141,9 @@
 	/* The destination becomes the initiator and vice versa */
 	msg->msg[0] = (cec_msg_destination(orig) << 4) |
 		      cec_msg_initiator(orig);
-	msg->reply = msg->timeout = 0;
+	msg->reply = 0;
+	msg->timeout = 0;
+	msg->flags = 0;
 }
 
 /* cec_msg flags field */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/const.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/const.h
@@ -28,7 +28,7 @@
 #define _BITUL(x)	(_UL(1) << (x))
 #define _BITULL(x)	(_ULL(1) << (x))
 
-#define __ALIGN_KERNEL(x, a)		__ALIGN_KERNEL_MASK(x, (typeof(x))(a) - 1)
+#define __ALIGN_KERNEL(x, a)		__ALIGN_KERNEL_MASK(x, (__typeof__(x))(a) - 1)
 #define __ALIGN_KERNEL_MASK(x, mask)	(((x) + (mask)) & ~(mask))
 
 #define __KERNEL_DIV_ROUND_UP(n, d) (((n) + (d) - 1) / (d))
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/cyclades.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/cyclades.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+
+#ifndef _UAPI_LINUX_CYCLADES_H
+#define _UAPI_LINUX_CYCLADES_H
+
+#warning "Support for features provided by this header has been removed"
+#warning "Please consider updating your code"
+
+struct cyclades_monitor {
+	unsigned long int_count;
+	unsigned long char_count;
+	unsigned long char_max;
+	unsigned long char_last;
+};
+
+#define CYGETMON		0x435901
+#define CYGETTHRESH		0x435902
+#define CYSETTHRESH		0x435903
+#define CYGETDEFTHRESH		0x435904
+#define CYSETDEFTHRESH		0x435905
+#define CYGETTIMEOUT		0x435906
+#define CYSETTIMEOUT		0x435907
+#define CYGETDEFTIMEOUT		0x435908
+#define CYSETDEFTIMEOUT		0x435909
+#define CYSETRFLOW		0x43590a
+#define CYGETRFLOW		0x43590b
+#define CYSETRTSDTR_INV		0x43590c
+#define CYGETRTSDTR_INV		0x43590d
+#define CYZSETPOLLCYCLE		0x43590e
+#define CYZGETPOLLCYCLE		0x43590f
+#define CYGETCD1400VER		0x435910
+#define CYSETWAIT		0x435912
+#define CYGETWAIT		0x435913
+
+#endif /* _UAPI_LINUX_CYCLADES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/dma-buf.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/dma-buf.h
@@ -92,7 +92,7 @@
  * between them in actual uapi, they're just different numbers.
  */
 #define DMA_BUF_SET_NAME	_IOW(DMA_BUF_BASE, 1, const char *)
-#define DMA_BUF_SET_NAME_A	_IOW(DMA_BUF_BASE, 1, u32)
-#define DMA_BUF_SET_NAME_B	_IOW(DMA_BUF_BASE, 1, u64)
+#define DMA_BUF_SET_NAME_A	_IOW(DMA_BUF_BASE, 1, __u32)
+#define DMA_BUF_SET_NAME_B	_IOW(DMA_BUF_BASE, 1, __u64)
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/ethtool.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/ethtool.h
@@ -707,6 +707,49 @@
 };
 
 /**
+ * enum ethtool_mac_stats_src - source of ethtool MAC statistics
+ * @ETHTOOL_MAC_STATS_SRC_AGGREGATE:
+ *	if device supports a MAC merge layer, this retrieves the aggregate
+ *	statistics of the eMAC and pMAC. Otherwise, it retrieves just the
+ *	statistics of the single (express) MAC.
+ * @ETHTOOL_MAC_STATS_SRC_EMAC:
+ *	if device supports a MM layer, this retrieves the eMAC statistics.
+ *	Otherwise, it retrieves the statistics of the single (express) MAC.
+ * @ETHTOOL_MAC_STATS_SRC_PMAC:
+ *	if device supports a MM layer, this retrieves the pMAC statistics.
+ */
+enum ethtool_mac_stats_src {
+	ETHTOOL_MAC_STATS_SRC_AGGREGATE,
+	ETHTOOL_MAC_STATS_SRC_EMAC,
+	ETHTOOL_MAC_STATS_SRC_PMAC,
+};
+
+/**
+ * enum ethtool_mm_verify_status - status of MAC Merge Verify function
+ * @ETHTOOL_MM_VERIFY_STATUS_UNKNOWN:
+ *	verification status is unknown
+ * @ETHTOOL_MM_VERIFY_STATUS_INITIAL:
+ *	the 802.3 Verify State diagram is in the state INIT_VERIFICATION
+ * @ETHTOOL_MM_VERIFY_STATUS_VERIFYING:
+ *	the Verify State diagram is in the state VERIFICATION_IDLE,
+ *	SEND_VERIFY or WAIT_FOR_RESPONSE
+ * @ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED:
+ *	indicates that the Verify State diagram is in the state VERIFIED
+ * @ETHTOOL_MM_VERIFY_STATUS_FAILED:
+ *	the Verify State diagram is in the state VERIFY_FAIL
+ * @ETHTOOL_MM_VERIFY_STATUS_DISABLED:
+ *	verification of preemption operation is disabled
+ */
+enum ethtool_mm_verify_status {
+	ETHTOOL_MM_VERIFY_STATUS_UNKNOWN,
+	ETHTOOL_MM_VERIFY_STATUS_INITIAL,
+	ETHTOOL_MM_VERIFY_STATUS_VERIFYING,
+	ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED,
+	ETHTOOL_MM_VERIFY_STATUS_FAILED,
+	ETHTOOL_MM_VERIFY_STATUS_DISABLED,
+};
+
+/**
  * struct ethtool_gstrings - string set for data tagging
  * @cmd: Command number = %ETHTOOL_GSTRINGS
  * @string_set: String set ID; one of &enum ethtool_stringset
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/ethtool_netlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/ethtool_netlink.h
@@ -47,6 +47,8 @@
 	ETHTOOL_MSG_MODULE_EEPROM_GET,
 	ETHTOOL_MSG_STATS_GET,
 	ETHTOOL_MSG_PHC_VCLOCKS_GET,
+	ETHTOOL_MSG_MM_GET,
+	ETHTOOL_MSG_MM_SET,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_USER_CNT,
@@ -90,6 +92,8 @@
 	ETHTOOL_MSG_MODULE_EEPROM_GET_REPLY,
 	ETHTOOL_MSG_STATS_GET_REPLY,
 	ETHTOOL_MSG_PHC_VCLOCKS_GET_REPLY,
+	ETHTOOL_MSG_MM_GET_REPLY,
+	ETHTOOL_MSG_MM_NTF,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_KERNEL_CNT,
@@ -394,6 +398,7 @@
 	ETHTOOL_A_PAUSE_RX,				/* u8 */
 	ETHTOOL_A_PAUSE_TX,				/* u8 */
 	ETHTOOL_A_PAUSE_STATS,				/* nest - _PAUSE_STAT_* */
+	ETHTOOL_A_PAUSE_STATS_SRC,			/* u32 */
 
 	/* add new constants above here */
 	__ETHTOOL_A_PAUSE_CNT,
@@ -407,7 +412,9 @@
 	ETHTOOL_A_PAUSE_STAT_TX_FRAMES,
 	ETHTOOL_A_PAUSE_STAT_RX_FRAMES,
 
-	/* add new constants above here */
+	/* add new constants above here
+	 * adjust ETHTOOL_PAUSE_STAT_CNT if adding non-stats!
+	 */
 	__ETHTOOL_A_PAUSE_STAT_CNT,
 	ETHTOOL_A_PAUSE_STAT_MAX = (__ETHTOOL_A_PAUSE_STAT_CNT - 1)
 };
@@ -708,6 +715,8 @@
 
 	ETHTOOL_A_STATS_GRP,			/* nest - _A_STATS_GRP_* */
 
+	ETHTOOL_A_STATS_SRC,			/* u32 */
+
 	/* add new constants above here */
 	__ETHTOOL_A_STATS_CNT,
 	ETHTOOL_A_STATS_MAX = (__ETHTOOL_A_STATS_CNT - 1)
@@ -741,7 +750,7 @@
 
 	/* add new constants above here */
 	__ETHTOOL_A_STATS_GRP_CNT,
-	ETHTOOL_A_STATS_GRP_MAX = (__ETHTOOL_A_STATS_CNT - 1)
+	ETHTOOL_A_STATS_GRP_MAX = (__ETHTOOL_A_STATS_GRP_CNT - 1)
 };
 
 enum {
@@ -833,6 +842,49 @@
 	ETHTOOL_A_STATS_RMON_MAX = (__ETHTOOL_A_STATS_RMON_CNT - 1)
 };
 
+/* MAC Merge (802.3) */
+
+enum {
+	ETHTOOL_A_MM_STAT_UNSPEC,
+	ETHTOOL_A_MM_STAT_PAD,
+
+	/* aMACMergeFrameAssErrorCount */
+	ETHTOOL_A_MM_STAT_REASSEMBLY_ERRORS,	/* u64 */
+	/* aMACMergeFrameSmdErrorCount */
+	ETHTOOL_A_MM_STAT_SMD_ERRORS,		/* u64 */
+	/* aMACMergeFrameAssOkCount */
+	ETHTOOL_A_MM_STAT_REASSEMBLY_OK,	/* u64 */
+	/* aMACMergeFragCountRx */
+	ETHTOOL_A_MM_STAT_RX_FRAG_COUNT,	/* u64 */
+	/* aMACMergeFragCountTx */
+	ETHTOOL_A_MM_STAT_TX_FRAG_COUNT,	/* u64 */
+	/* aMACMergeHoldCount */
+	ETHTOOL_A_MM_STAT_HOLD_COUNT,		/* u64 */
+
+	/* add new constants above here */
+	__ETHTOOL_A_MM_STAT_CNT,
+	ETHTOOL_A_MM_STAT_MAX = (__ETHTOOL_A_MM_STAT_CNT - 1)
+};
+
+enum {
+	ETHTOOL_A_MM_UNSPEC,
+	ETHTOOL_A_MM_HEADER,			/* nest - _A_HEADER_* */
+	ETHTOOL_A_MM_PMAC_ENABLED,		/* u8 */
+	ETHTOOL_A_MM_TX_ENABLED,		/* u8 */
+	ETHTOOL_A_MM_TX_ACTIVE,			/* u8 */
+	ETHTOOL_A_MM_TX_MIN_FRAG_SIZE,		/* u32 */
+	ETHTOOL_A_MM_RX_MIN_FRAG_SIZE,		/* u32 */
+	ETHTOOL_A_MM_VERIFY_ENABLED,		/* u8 */
+	ETHTOOL_A_MM_VERIFY_STATUS,		/* u8 */
+	ETHTOOL_A_MM_VERIFY_TIME,		/* u32 */
+	ETHTOOL_A_MM_MAX_VERIFY_TIME,		/* u32 */
+	ETHTOOL_A_MM_STATS,			/* nest - _A_MM_STAT_* */
+
+	/* add new constants above here */
+	__ETHTOOL_A_MM_CNT,
+	ETHTOOL_A_MM_MAX = (__ETHTOOL_A_MM_CNT - 1)
+};
+
 /* generic netlink info */
 #define ETHTOOL_GENL_NAME "ethtool"
 #define ETHTOOL_GENL_VERSION 1
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/eventpoll.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/eventpoll.h
@@ -41,6 +41,12 @@
 #define EPOLLMSG	(__force __poll_t)0x00000400
 #define EPOLLRDHUP	(__force __poll_t)0x00002000
 
+/*
+ * Internal flag - wakeup generated by io_uring, used to detect recursion back
+ * into the io_uring poll handler.
+ */
+#define EPOLL_URING_WAKE	((__force __poll_t)(1U << 27))
+
 /* Set exclusive wakeup mode for the target file descriptor */
 #define EPOLLEXCLUSIVE	((__force __poll_t)(1U << 28))
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/fanotify.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/fanotify.h
@@ -20,6 +20,7 @@
 #define FAN_OPEN_EXEC		0x00001000	/* File was opened for exec */
 
 #define FAN_Q_OVERFLOW		0x00004000	/* Event queued overflowed */
+#define FAN_FS_ERROR		0x00008000	/* Filesystem error */
 
 #define FAN_OPEN_PERM		0x00010000	/* File open in perm check */
 #define FAN_ACCESS_PERM		0x00020000	/* File accessed in perm check */
@@ -27,6 +28,8 @@
 
 #define FAN_EVENT_ON_CHILD	0x08000000	/* Interested in child events */
 
+#define FAN_RENAME		0x10000000	/* File was renamed */
+
 #define FAN_ONDIR		0x40000000	/* Event occurred against dir */
 
 /* helper events */
@@ -56,9 +59,13 @@
 #define FAN_REPORT_FID		0x00000200	/* Report unique file id */
 #define FAN_REPORT_DIR_FID	0x00000400	/* Report unique directory id */
 #define FAN_REPORT_NAME		0x00000800	/* Report events with name */
+#define FAN_REPORT_TARGET_FID	0x00001000	/* Report dirent target id  */
 
 /* Convenience macro - FAN_REPORT_NAME requires FAN_REPORT_DIR_FID */
 #define FAN_REPORT_DFID_NAME	(FAN_REPORT_DIR_FID | FAN_REPORT_NAME)
+/* Convenience macro - FAN_REPORT_TARGET_FID requires all other FID flags */
+#define FAN_REPORT_DFID_NAME_TARGET (FAN_REPORT_DFID_NAME | \
+				     FAN_REPORT_FID | FAN_REPORT_TARGET_FID)
 
 /* Deprecated - do not use this in programs and do not add new flags here! */
 #define FAN_ALL_INIT_FLAGS	(FAN_CLOEXEC | FAN_NONBLOCK | \
@@ -75,12 +82,21 @@
 #define FAN_MARK_IGNORED_SURV_MODIFY	0x00000040
 #define FAN_MARK_FLUSH		0x00000080
 /* FAN_MARK_FILESYSTEM is	0x00000100 */
+#define FAN_MARK_EVICTABLE	0x00000200
+/* This bit is mutually exclusive with FAN_MARK_IGNORED_MASK bit */
+#define FAN_MARK_IGNORE		0x00000400
 
 /* These are NOT bitwise flags.  Both bits can be used togther.  */
 #define FAN_MARK_INODE		0x00000000
 #define FAN_MARK_MOUNT		0x00000010
 #define FAN_MARK_FILESYSTEM	0x00000100
 
+/*
+ * Convenience macro - FAN_MARK_IGNORE requires FAN_MARK_IGNORED_SURV_MODIFY
+ * for non-inode mark types.
+ */
+#define FAN_MARK_IGNORE_SURV	(FAN_MARK_IGNORE | FAN_MARK_IGNORED_SURV_MODIFY)
+
 /* Deprecated - do not use this in programs and do not add new flags here! */
 #define FAN_ALL_MARK_FLAGS	(FAN_MARK_ADD |\
 				 FAN_MARK_REMOVE |\
@@ -125,6 +141,13 @@
 #define FAN_EVENT_INFO_TYPE_DFID_NAME	2
 #define FAN_EVENT_INFO_TYPE_DFID	3
 #define FAN_EVENT_INFO_TYPE_PIDFD	4
+#define FAN_EVENT_INFO_TYPE_ERROR	5
+
+/* Special info types for FAN_RENAME */
+#define FAN_EVENT_INFO_TYPE_OLD_DFID_NAME	10
+/* Reserved for FAN_EVENT_INFO_TYPE_OLD_DFID	11 */
+#define FAN_EVENT_INFO_TYPE_NEW_DFID_NAME	12
+/* Reserved for FAN_EVENT_INFO_TYPE_NEW_DFID	13 */
 
 /* Variable length info record following event metadata */
 struct fanotify_event_info_header {
@@ -159,6 +182,12 @@
 	__s32 pidfd;
 };
 
+struct fanotify_event_info_error {
+	struct fanotify_event_info_header hdr;
+	__s32 error;
+	__u32 error_count;
+};
+
 struct fanotify_response {
 	__s32 fd;
 	__u32 response;
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/gtp.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/gtp.h
@@ -32,6 +32,6 @@
 	GTPA_PAD,
 	__GTPA_MAX,
 };
-#define GTPA_MAX (__GTPA_MAX + 1)
+#define GTPA_MAX (__GTPA_MAX - 1)
 
 #endif /* _UAPI_LINUX_GTP_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/idxd.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/idxd.h
@@ -272,7 +272,7 @@
 		};
 
 		uint32_t	delta_rec_size;
-		uint32_t	crc_val;
+		uint64_t	crc_val;
 
 		/* DIF check & strip */
 		struct {
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/if_link.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/if_link.h
@@ -743,6 +743,7 @@
 	IFLA_VXLAN_GPE,
 	IFLA_VXLAN_TTL_INHERIT,
 	IFLA_VXLAN_DF,
+	IFLA_VXLAN_FAN_MAP = 33,
 	__IFLA_VXLAN_MAX
 };
 #define IFLA_VXLAN_MAX	(__IFLA_VXLAN_MAX - 1)
@@ -776,6 +777,7 @@
 	IFLA_GENEVE_LABEL,
 	IFLA_GENEVE_TTL_INHERIT,
 	IFLA_GENEVE_DF,
+	IFLA_GENEVE_INNER_PROTO_INHERIT,
 	__IFLA_GENEVE_MAX
 };
 #define IFLA_GENEVE_MAX	(__IFLA_GENEVE_MAX - 1)
@@ -858,6 +860,7 @@
 	IFLA_BOND_TLB_DYNAMIC_LB,
 	IFLA_BOND_PEER_NOTIF_DELAY,
 	IFLA_BOND_AD_LACP_ACTIVE,
+	IFLA_BOND_MISSED_MAX,
 	__IFLA_BOND_MAX,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/if_tunnel.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/if_tunnel.h
@@ -77,6 +77,10 @@
 	IFLA_IPTUN_ENCAP_DPORT,
 	IFLA_IPTUN_COLLECT_METADATA,
 	IFLA_IPTUN_FWMARK,
+
+	__IFLA_IPTUN_VENDOR_BREAK, /* Ensure new entries do not hit the below. */
+	IFLA_IPTUN_FAN_MAP = 33,
+
 	__IFLA_IPTUN_MAX,
 };
 #define IFLA_IPTUN_MAX	(__IFLA_IPTUN_MAX - 1)
@@ -180,4 +184,19 @@
 #define TUNNEL_OPTIONS_PRESENT \
 		(TUNNEL_GENEVE_OPT | TUNNEL_VXLAN_OPT | TUNNEL_ERSPAN_OPT)
 
+enum {
+	IFLA_FAN_UNSPEC,
+	IFLA_FAN_MAPPING,
+	__IFLA_FAN_MAX,
+};
+
+#define IFLA_FAN_MAX (__IFLA_FAN_MAX - 1)
+
+struct ifla_fan_map {
+	__be32		underlay;
+	__be32		overlay;
+	__u16		underlay_prefix;
+	__u16		overlay_prefix;
+};
+
 #endif /* _UAPI_IF_TUNNEL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/in.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/in.h
@@ -159,6 +159,8 @@
 #define MCAST_MSFILTER			48
 #define IP_MULTICAST_ALL		49
 #define IP_UNICAST_IF			50
+#define IP_LOCAL_PORT_RANGE		51
+#define IP_PROTOCOL			52
 
 #define MCAST_EXCLUDE	0
 #define MCAST_INCLUDE	1
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/in6.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/in6.h
@@ -145,7 +145,7 @@
 #define IPV6_TLV_PADN		1
 #define IPV6_TLV_ROUTERALERT	5
 #define IPV6_TLV_CALIPSO	7	/* RFC 5570 */
-#define IPV6_TLV_IOAM		49	/* TEMPORARY IANA allocation for IOAM */
+#define IPV6_TLV_IOAM		49	/* RFC 9486 */
 #define IPV6_TLV_JUMBO		194
 #define IPV6_TLV_HAO		201	/* home address option */
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/input-event-codes.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/input-event-codes.h
@@ -278,7 +278,8 @@
 #define KEY_PAUSECD		201
 #define KEY_PROG3		202
 #define KEY_PROG4		203
-#define KEY_DASHBOARD		204	/* AL Dashboard */
+#define KEY_ALL_APPLICATIONS	204	/* AC Desktop Show All Applications */
+#define KEY_DASHBOARD		KEY_ALL_APPLICATIONS
 #define KEY_SUSPEND		205
 #define KEY_CLOSE		206	/* AC Close */
 #define KEY_PLAY		207
@@ -518,6 +519,7 @@
 #define KEY_NOTIFICATION_CENTER	0x1bc	/* Show/hide the notification center */
 #define KEY_PICKUP_PHONE	0x1bd	/* Answer incoming call */
 #define KEY_HANGUP_PHONE	0x1be	/* Decline incoming call */
+#define KEY_LINK_PHONE		0x1bf   /* AL Phone Syncing */
 
 #define KEY_DEL_EOL		0x1c0
 #define KEY_DEL_EOS		0x1c1
@@ -601,6 +603,7 @@
 
 #define KEY_ALS_TOGGLE		0x230	/* Ambient light sensor */
 #define KEY_ROTATE_LOCK_TOGGLE	0x231	/* Display rotation lock */
+#define KEY_REFRESH_RATE_TOGGLE	0x232	/* Display refresh rate toggle */
 
 #define KEY_BUTTONCONFIG		0x240	/* AL Button Configuration */
 #define KEY_TASKMANAGER		0x241	/* AL Task/Project Manager */
@@ -612,6 +615,7 @@
 #define KEY_ASSISTANT		0x247	/* AL Context-aware desktop assistant */
 #define KEY_KBD_LAYOUT_NEXT	0x248	/* AC Next Keyboard Layout Select */
 #define KEY_EMOJI_PICKER	0x249	/* Show/hide emoji picker (HUTRR101) */
+#define KEY_DICTATE		0x24a	/* Start or Stop Voice Dictation Session (HUTRR99) */
 
 #define KEY_BRIGHTNESS_MIN		0x250	/* Set Brightness to Minimum */
 #define KEY_BRIGHTNESS_MAX		0x251	/* Set Brightness to Maximum */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/ip.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/ip.h
@@ -18,6 +18,7 @@
 #ifndef _UAPI_LINUX_IP_H
 #define _UAPI_LINUX_IP_H
 #include <linux/types.h>
+#include <linux/stddef.h>
 #include <asm/byteorder.h>
 
 #define IPTOS_TOS_MASK		0x1E
@@ -100,8 +101,10 @@
 	__u8	ttl;
 	__u8	protocol;
 	__sum16	check;
-	__be32	saddr;
-	__be32	daddr;
+	__struct_group(/* no tag */, addrs, /* no attrs */,
+		__be32	saddr;
+		__be32	daddr;
+	);
 	/*The options start here. */
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/ipu-isys.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/ipu-isys.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/* Copyright (C) 2016 - 2020 Intel Corporation */
+
+#ifndef UAPI_LINUX_IPU_ISYS_H
+#define UAPI_LINUX_IPU_ISYS_H
+
+#define V4L2_CID_IPU_BASE	(V4L2_CID_USER_BASE + 0x1080)
+
+#define V4L2_CID_IPU_STORE_CSI2_HEADER	(V4L2_CID_IPU_BASE + 2)
+#define V4L2_CID_IPU_ISYS_COMPRESSION	(V4L2_CID_IPU_BASE + 3)
+
+#define VIDIOC_IPU_GET_DRIVER_VERSION \
+	_IOWR('v', BASE_VIDIOC_PRIVATE + 3, uint32_t)
+
+#endif /* UAPI_LINUX_IPU_ISYS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/ipu-psys.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/ipu-psys.h
@@ -0,0 +1,121 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/* Copyright (C) 2013 - 2020 Intel Corporation */
+
+#ifndef _UAPI_IPU_PSYS_H
+#define _UAPI_IPU_PSYS_H
+
+#ifdef __KERNEL__
+#include <linux/types.h>
+#else
+#include <stdint.h>
+#endif
+
+struct ipu_psys_capability {
+	uint32_t version;
+	uint8_t driver[20];
+	uint32_t pg_count;
+	uint8_t dev_model[32];
+	uint32_t reserved[17];
+} __attribute__ ((packed));
+
+struct ipu_psys_event {
+	uint32_t type;		/* IPU_PSYS_EVENT_TYPE_ */
+	uint64_t user_token;
+	uint64_t issue_id;
+	uint32_t buffer_idx;
+	uint32_t error;
+	int32_t reserved[2];
+} __attribute__ ((packed));
+
+#define IPU_PSYS_EVENT_TYPE_CMD_COMPLETE	1
+#define IPU_PSYS_EVENT_TYPE_BUFFER_COMPLETE	2
+
+/**
+ * struct ipu_psys_buffer - for input/output terminals
+ * @len:	total allocated size @ base address
+ * @userptr:	user pointer
+ * @fd:		DMA-BUF handle
+ * @data_offset:offset to valid data
+ * @bytes_used:	amount of valid data including offset
+ * @flags:	flags
+ */
+struct ipu_psys_buffer {
+	uint64_t len;
+	union {
+		int fd;
+		void __user *userptr;
+		uint64_t reserved;
+	} base;
+	uint32_t data_offset;
+	uint32_t bytes_used;
+	uint32_t flags;
+	uint32_t reserved[2];
+} __attribute__ ((packed));
+
+#define IPU_BUFFER_FLAG_INPUT	(1 << 0)
+#define IPU_BUFFER_FLAG_OUTPUT	(1 << 1)
+#define IPU_BUFFER_FLAG_MAPPED	(1 << 2)
+#define IPU_BUFFER_FLAG_NO_FLUSH	(1 << 3)
+#define IPU_BUFFER_FLAG_DMA_HANDLE	(1 << 4)
+#define IPU_BUFFER_FLAG_USERPTR	(1 << 5)
+
+#define	IPU_PSYS_CMD_PRIORITY_HIGH	0
+#define	IPU_PSYS_CMD_PRIORITY_MED	1
+#define	IPU_PSYS_CMD_PRIORITY_LOW	2
+#define	IPU_PSYS_CMD_PRIORITY_NUM	3
+
+/**
+ * struct ipu_psys_command - processing command
+ * @issue_id:		unique id for the command set by user
+ * @user_token:		token of the command
+ * @priority:		priority of the command
+ * @pg_manifest:	userspace pointer to program group manifest
+ * @buffers:		userspace pointers to array of psys dma buf structs
+ * @pg:			process group DMA-BUF handle
+ * @pg_manifest_size:	size of program group manifest
+ * @bufcount:		number of buffers in buffers array
+ * @min_psys_freq:	minimum psys frequency in MHz used for this cmd
+ * @frame_counter:      counter of current frame synced between isys and psys
+ * @kernel_enable_bitmap:       enable bits for each individual kernel
+ * @terminal_enable_bitmap:     enable bits for each individual terminals
+ * @routing_enable_bitmap:      enable bits for each individual routing
+ * @rbm:                        enable bits for routing
+ *
+ * Specifies a processing command with input and output buffers.
+ */
+struct ipu_psys_command {
+	uint64_t issue_id;
+	uint64_t user_token;
+	uint32_t priority;
+	void __user *pg_manifest;
+	struct ipu_psys_buffer __user *buffers;
+	int pg;
+	uint32_t pg_manifest_size;
+	uint32_t bufcount;
+	uint32_t min_psys_freq;
+	uint32_t frame_counter;
+	uint32_t kernel_enable_bitmap[4];
+	uint32_t terminal_enable_bitmap[4];
+	uint32_t routing_enable_bitmap[4];
+	uint32_t rbm[5];
+	uint32_t reserved[2];
+} __attribute__ ((packed));
+
+struct ipu_psys_manifest {
+	uint32_t index;
+	uint32_t size;
+	void __user *manifest;
+	uint32_t reserved[5];
+} __attribute__ ((packed));
+
+#define IPU_IOC_QUERYCAP _IOR('A', 1, struct ipu_psys_capability)
+#define IPU_IOC_MAPBUF _IOWR('A', 2, int)
+#define IPU_IOC_UNMAPBUF _IOWR('A', 3, int)
+#define IPU_IOC_GETBUF _IOWR('A', 4, struct ipu_psys_buffer)
+#define IPU_IOC_PUTBUF _IOWR('A', 5, struct ipu_psys_buffer)
+#define IPU_IOC_QCMD _IOWR('A', 6, struct ipu_psys_command)
+#define IPU_IOC_DQEVENT _IOWR('A', 7, struct ipu_psys_event)
+#define IPU_IOC_CMD_CANCEL _IOWR('A', 8, struct ipu_psys_command)
+#define IPU_IOC_GET_MANIFEST _IOWR('A', 9, struct ipu_psys_manifest)
+
+#endif /* _UAPI_IPU_PSYS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/ipv6.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/ipv6.h
@@ -4,6 +4,7 @@
 
 #include <linux/libc-compat.h>
 #include <linux/types.h>
+#include <linux/stddef.h>
 #include <linux/in6.h>
 #include <asm/byteorder.h>
 
@@ -130,8 +131,10 @@
 	__u8			nexthdr;
 	__u8			hop_limit;
 
-	struct	in6_addr	saddr;
-	struct	in6_addr	daddr;
+	__struct_group(/* no tag */, addrs, /* no attrs */,
+		struct	in6_addr	saddr;
+		struct	in6_addr	daddr;
+	);
 };
 
 
@@ -193,6 +196,9 @@
 	DEVCONF_IOAM6_ENABLED,
 	DEVCONF_IOAM6_ID,
 	DEVCONF_IOAM6_ID_WIDE,
+	DEVCONF_NDISC_EVICT_NOCARRIER,
+	DEVCONF_ACCEPT_UNTRACKED_NA,
+	DEVCONF_ACCEPT_RA_MIN_LFT,
 	DEVCONF_MAX
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/kvm.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/kvm.h
@@ -544,9 +544,12 @@
 	__u32 op;		/* type of operation */
 	__u64 buf;		/* buffer in userspace */
 	union {
-		__u8 ar;	/* the access register number */
+		struct {
+			__u8 ar;	/* the access register number */
+			__u8 key;	/* access key, ignored if flag unset */
+		};
 		__u32 sida_offset; /* offset into the sida */
-		__u8 reserved[32]; /* should be set to 0 */
+		__u8 reserved[32]; /* ignored */
 	};
 };
 /* types for kvm_s390_mem_op->op */
@@ -554,9 +557,12 @@
 #define KVM_S390_MEMOP_LOGICAL_WRITE	1
 #define KVM_S390_MEMOP_SIDA_READ	2
 #define KVM_S390_MEMOP_SIDA_WRITE	3
+#define KVM_S390_MEMOP_ABSOLUTE_READ	4
+#define KVM_S390_MEMOP_ABSOLUTE_WRITE	5
 /* flags for kvm_s390_mem_op->flags */
 #define KVM_S390_MEMOP_F_CHECK_ONLY		(1ULL << 0)
 #define KVM_S390_MEMOP_F_INJECT_EXCEPTION	(1ULL << 1)
+#define KVM_S390_MEMOP_F_SKEY_PROTECTION	(1ULL << 2)
 
 /* for KVM_INTERRUPT */
 struct kvm_interrupt {
@@ -1112,6 +1118,13 @@
 #define KVM_CAP_BINARY_STATS_FD 203
 #define KVM_CAP_EXIT_ON_EMULATION_FAILURE 204
 #define KVM_CAP_ARM_MTE 205
+#define KVM_CAP_VM_MOVE_ENC_CONTEXT_FROM 206
+#define KVM_CAP_VM_GPA_BITS 207
+#define KVM_CAP_XSAVE2 208
+#define KVM_CAP_SYS_ATTRIBUTES 209
+#define KVM_CAP_S390_MEM_OP_EXTENSION 211
+#define KVM_CAP_S390_ZPCI_OP 221
+#define KVM_CAP_S390_PROTECTED_DUMP 217
 
 #ifdef KVM_CAP_IRQ_ROUTING
 
@@ -1597,6 +1610,55 @@
 	__u64 tweak;
 };
 
+enum pv_cmd_dmp_id {
+	KVM_PV_DUMP_INIT,
+	KVM_PV_DUMP_CONFIG_STOR_STATE,
+	KVM_PV_DUMP_COMPLETE,
+	KVM_PV_DUMP_CPU,
+};
+
+struct kvm_s390_pv_dmp {
+	__u64 subcmd;
+	__u64 buff_addr;
+	__u64 buff_len;
+	__u64 gaddr;		/* For dump storage state */
+	__u64 reserved[4];
+};
+
+enum pv_cmd_info_id {
+	KVM_PV_INFO_VM,
+	KVM_PV_INFO_DUMP,
+};
+
+struct kvm_s390_pv_info_dump {
+	__u64 dump_cpu_buffer_len;
+	__u64 dump_config_mem_buffer_per_1m;
+	__u64 dump_config_finalize_len;
+};
+
+struct kvm_s390_pv_info_vm {
+	__u64 inst_calls_list[4];
+	__u64 max_cpus;
+	__u64 max_guests;
+	__u64 max_guest_addr;
+	__u64 feature_indication;
+};
+
+struct kvm_s390_pv_info_header {
+	__u32 id;
+	__u32 len_max;
+	__u32 len_written;
+	__u32 reserved;
+};
+
+struct kvm_s390_pv_info {
+	struct kvm_s390_pv_info_header header;
+	union {
+		struct kvm_s390_pv_info_dump dump;
+		struct kvm_s390_pv_info_vm vm;
+	};
+};
+
 enum pv_cmd_id {
 	KVM_PV_ENABLE,
 	KVM_PV_DISABLE,
@@ -1605,6 +1667,8 @@
 	KVM_PV_VERIFY,
 	KVM_PV_PREP_RESET,
 	KVM_PV_UNSHARE_ALL,
+	KVM_PV_INFO,
+	KVM_PV_DUMP,
 };
 
 struct kvm_pv_cmd {
@@ -2007,4 +2071,37 @@
 
 #define KVM_GET_STATS_FD  _IO(KVMIO,  0xce)
 
+/* Available with KVM_CAP_S390_ZPCI_OP */
+#define KVM_S390_ZPCI_OP         _IOW(KVMIO,  0xd1, struct kvm_s390_zpci_op)
+
+struct kvm_s390_zpci_op {
+	/* in */
+	__u32 fh;               /* target device */
+	__u8  op;               /* operation to perform */
+	__u8  pad[3];
+	union {
+		/* for KVM_S390_ZPCIOP_REG_AEN */
+		struct {
+			__u64 ibv;      /* Guest addr of interrupt bit vector */
+			__u64 sb;       /* Guest addr of summary bit */
+			__u32 flags;
+			__u32 noi;      /* Number of interrupts */
+			__u8 isc;       /* Guest interrupt subclass */
+			__u8 sbo;       /* Offset of guest summary bit vector */
+			__u16 pad;
+		} reg_aen;
+		__u64 reserved[8];
+	} u;
+};
+
+/* types for kvm_s390_zpci_op->op */
+#define KVM_S390_ZPCIOP_REG_AEN                0
+#define KVM_S390_ZPCIOP_DEREG_AEN      1
+
+/* flags for kvm_s390_zpci_op->u.reg_aen.flags */
+#define KVM_S390_ZPCIOP_REGAEN_HOST    (1 << 0)
+
+/* Available with KVM_CAP_S390_PROTECTED_DUMP */
+#define KVM_S390_PV_CPU_COMMAND	_IOWR(KVMIO, 0xd0, struct kvm_pv_cmd)
+
 #endif /* __LINUX_KVM_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/landlock.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/landlock.h
@@ -33,7 +33,9 @@
  * - %LANDLOCK_CREATE_RULESET_VERSION: Get the highest supported Landlock ABI
  *   version.
  */
+/* clang-format off */
 #define LANDLOCK_CREATE_RULESET_VERSION			(1U << 0)
+/* clang-format on */
 
 /**
  * enum landlock_rule_type - Landlock rule type
@@ -60,8 +62,9 @@
 	 */
 	__u64 allowed_access;
 	/**
-	 * @parent_fd: File descriptor, open with ``O_PATH``, which identifies
-	 * the parent directory of a file hierarchy, or just a file.
+	 * @parent_fd: File descriptor, preferably opened with ``O_PATH``,
+	 * which identifies the parent directory of a file hierarchy, or just a
+	 * file.
 	 */
 	__s32 parent_fd;
 	/*
@@ -120,6 +123,7 @@
  *   :manpage:`access(2)`.
  *   Future Landlock evolutions will enable to restrict them.
  */
+/* clang-format off */
 #define LANDLOCK_ACCESS_FS_EXECUTE			(1ULL << 0)
 #define LANDLOCK_ACCESS_FS_WRITE_FILE			(1ULL << 1)
 #define LANDLOCK_ACCESS_FS_READ_FILE			(1ULL << 2)
@@ -133,5 +137,6 @@
 #define LANDLOCK_ACCESS_FS_MAKE_FIFO			(1ULL << 10)
 #define LANDLOCK_ACCESS_FS_MAKE_BLOCK			(1ULL << 11)
 #define LANDLOCK_ACCESS_FS_MAKE_SYM			(1ULL << 12)
+/* clang-format on */
 
 #endif /* _UAPI_LINUX_LANDLOCK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/magic.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/magic.h
@@ -99,4 +99,6 @@
 #define PPC_CMM_MAGIC		0xc7571590
 #define SECRETMEM_MAGIC		0x5345434d	/* "SECM" */
 
+#define SHIFTFS_MAGIC		0x6a656a62
+
 #endif /* __LINUX_MAGIC_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/media-bus-format.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/media-bus-format.h
@@ -157,6 +157,22 @@
 /* HSV - next is	0x6002 */
 #define MEDIA_BUS_FMT_AHSV8888_1X32		0x6001
 
+/* RGB: Xilinx Specific - next is        0x1103 */
+#define MEDIA_BUS_FMT_RBG101010_1X30		0x1100
+#define MEDIA_BUS_FMT_RBG121212_1X36		0x1101
+#define MEDIA_BUS_FMT_RBG161616_1X48		0x1102
+
+/* YUV: Xilinx Specific - next is       0x2109 */
+#define MEDIA_BUS_FMT_VYYUYY8_1X24		0x2100
+#define MEDIA_BUS_FMT_VYYUYY10_4X20		0x2101
+#define MEDIA_BUS_FMT_VUY10_1X30		0x2102
+#define MEDIA_BUS_FMT_UYYVYY12_4X24		0x2103
+#define MEDIA_BUS_FMT_VUY12_1X36		0x2104
+#define MEDIA_BUS_FMT_Y16_1X16			0x2105
+#define MEDIA_BUS_FMT_UYYVYY16_4X32		0x2106
+#define MEDIA_BUS_FMT_VUY16_1X48		0x2107
+#define MEDIA_BUS_FMT_UYVY16_2X32		0x2108
+
 /*
  * This format should be used when the same driver handles
  * both sides of the link and the bus format is a fixed
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/mptcp.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/mptcp.h
@@ -129,19 +129,21 @@
  * MPTCP_EVENT_REMOVED: token, rem_id
  * An address has been lost by the peer.
  *
- * MPTCP_EVENT_SUB_ESTABLISHED: token, family, saddr4 | saddr6,
- *                              daddr4 | daddr6, sport, dport, backup,
- *                              if_idx [, error]
+ * MPTCP_EVENT_SUB_ESTABLISHED: token, family, loc_id, rem_id,
+ *                              saddr4 | saddr6, daddr4 | daddr6, sport,
+ *                              dport, backup, if_idx [, error]
  * A new subflow has been established. 'error' should not be set.
  *
- * MPTCP_EVENT_SUB_CLOSED: token, family, saddr4 | saddr6, daddr4 | daddr6,
- *                         sport, dport, backup, if_idx [, error]
+ * MPTCP_EVENT_SUB_CLOSED: token, family, loc_id, rem_id, saddr4 | saddr6,
+ *                         daddr4 | daddr6, sport, dport, backup, if_idx
+ *                         [, error]
  * A subflow has been closed. An error (copy of sk_err) could be set if an
  * error has been detected for this subflow.
  *
- * MPTCP_EVENT_SUB_PRIORITY: token, family, saddr4 | saddr6, daddr4 | daddr6,
- *                           sport, dport, backup, if_idx [, error]
- *       The priority of a subflow has changed. 'error' should not be set.
+ * MPTCP_EVENT_SUB_PRIORITY: token, family, loc_id, rem_id, saddr4 | saddr6,
+ *                           daddr4 | daddr6, sport, dport, backup, if_idx
+ *                           [, error]
+ * The priority of a subflow has changed. 'error' should not be set.
  */
 enum mptcp_event_type {
 	MPTCP_EVENT_UNSPEC = 0,
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netfilter/nf_conntrack_common.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netfilter/nf_conntrack_common.h
@@ -106,7 +106,7 @@
 	IPS_NAT_CLASH = IPS_UNTRACKED,
 #endif
 
-	/* Conntrack got a helper explicitly attached via CT target. */
+	/* Conntrack got a helper explicitly attached (ruleset, ctnetlink). */
 	IPS_HELPER_BIT = 13,
 	IPS_HELPER = (1 << IPS_HELPER_BIT),
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netfilter/nf_conntrack_sctp.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netfilter/nf_conntrack_sctp.h
@@ -15,7 +15,7 @@
 	SCTP_CONNTRACK_SHUTDOWN_RECD,
 	SCTP_CONNTRACK_SHUTDOWN_ACK_SENT,
 	SCTP_CONNTRACK_HEARTBEAT_SENT,
-	SCTP_CONNTRACK_HEARTBEAT_ACKED,
+	SCTP_CONNTRACK_HEARTBEAT_ACKED,	/* no longer used */
 	SCTP_CONNTRACK_MAX
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netfilter/nf_tables.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netfilter/nf_tables.h
@@ -266,9 +266,11 @@
 /**
  * enum nft_rule_compat_flags - nf_tables rule compat flags
  *
+ * @NFT_RULE_COMPAT_F_UNUSED: unused
  * @NFT_RULE_COMPAT_F_INV: invert the check result
  */
 enum nft_rule_compat_flags {
+	NFT_RULE_COMPAT_F_UNUSED = (1 << 0),
 	NFT_RULE_COMPAT_F_INV	= (1 << 1),
 	NFT_RULE_COMPAT_F_MASK	= NFT_RULE_COMPAT_F_INV,
 };
@@ -753,11 +755,13 @@
  * @NFT_PAYLOAD_LL_HEADER: link layer header
  * @NFT_PAYLOAD_NETWORK_HEADER: network header
  * @NFT_PAYLOAD_TRANSPORT_HEADER: transport header
+ * @NFT_PAYLOAD_INNER_HEADER: inner header / payload
  */
 enum nft_payload_bases {
 	NFT_PAYLOAD_LL_HEADER,
 	NFT_PAYLOAD_NETWORK_HEADER,
 	NFT_PAYLOAD_TRANSPORT_HEADER,
+	NFT_PAYLOAD_INNER_HEADER,
 };
 
 /**
@@ -1316,7 +1320,7 @@
 #define NFTA_SECMARK_MAX	(__NFTA_SECMARK_MAX - 1)
 
 /* Max security context length */
-#define NFT_SECMARK_CTX_MAXLEN		256
+#define NFT_SECMARK_CTX_MAXLEN		4096
 
 /**
  * enum nft_reject_types - nf_tables reject expression reject types
@@ -1634,7 +1638,7 @@
  *
  * @NFTA_FLOWTABLE_TABLE: name of the table containing the expression (NLA_STRING)
  * @NFTA_FLOWTABLE_NAME: name of this flow table (NLA_STRING)
- * @NFTA_FLOWTABLE_HOOK: netfilter hook configuration(NLA_U32)
+ * @NFTA_FLOWTABLE_HOOK: netfilter hook configuration (NLA_NESTED)
  * @NFTA_FLOWTABLE_USE: number of references to this flow table (NLA_U32)
  * @NFTA_FLOWTABLE_HANDLE: object handle (NLA_U64)
  * @NFTA_FLOWTABLE_FLAGS: flags (NLA_U32)
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netfilter/nfnetlink_cttimeout.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netfilter/nfnetlink_cttimeout.h
@@ -94,7 +94,7 @@
 	CTA_TIMEOUT_SCTP_SHUTDOWN_RECD,
 	CTA_TIMEOUT_SCTP_SHUTDOWN_ACK_SENT,
 	CTA_TIMEOUT_SCTP_HEARTBEAT_SENT,
-	CTA_TIMEOUT_SCTP_HEARTBEAT_ACKED,
+	CTA_TIMEOUT_SCTP_HEARTBEAT_ACKED, /* no longer used */
 	__CTA_TIMEOUT_SCTP_MAX
 };
 #define CTA_TIMEOUT_SCTP_MAX (__CTA_TIMEOUT_SCTP_MAX - 1)
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netfilter/xt_IDLETIMER.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netfilter/xt_IDLETIMER.h
@@ -1,6 +1,5 @@
+/* SPDX-License-Identifier: GPL-2.0-only WITH Linux-syscall-note */
 /*
- * linux/include/linux/netfilter/xt_IDLETIMER.h
- *
  * Header file for Xtables timer target module.
  *
  * Copyright (C) 2004, 2010 Nokia Corporation
@@ -10,20 +9,6 @@
  * by Luciano Coelho <luciano.coelho@nokia.com>
  *
  * Contact: Luciano Coelho <luciano.coelho@nokia.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
  */
 
 #ifndef _XT_IDLETIMER_H
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netfilter_bridge/ebtables.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netfilter_bridge/ebtables.h
@@ -182,12 +182,14 @@
 	unsigned char sourcemsk[ETH_ALEN];
 	unsigned char destmac[ETH_ALEN];
 	unsigned char destmsk[ETH_ALEN];
-	/* sizeof ebt_entry + matches */
-	unsigned int watchers_offset;
-	/* sizeof ebt_entry + matches + watchers */
-	unsigned int target_offset;
-	/* sizeof ebt_entry + matches + watchers + target */
-	unsigned int next_offset;
+	__struct_group(/* no tag */, offsets, /* no attrs */,
+		/* sizeof ebt_entry + matches */
+		unsigned int watchers_offset;
+		/* sizeof ebt_entry + matches + watchers */
+		unsigned int target_offset;
+		/* sizeof ebt_entry + matches + watchers + target */
+		unsigned int next_offset;
+	);
 	unsigned char elems[0] __attribute__ ((aligned (__alignof__(struct ebt_replace))));
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/netlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/netlink.h
@@ -20,7 +20,7 @@
 #define NETLINK_CONNECTOR	11
 #define NETLINK_NETFILTER	12	/* netfilter subsystem */
 #define NETLINK_IP6_FW		13
-#define NETLINK_DNRTMSG		14	/* DECnet routing messages */
+#define NETLINK_DNRTMSG		14	/* DECnet routing messages (obsolete) */
 #define NETLINK_KOBJECT_UEVENT	15	/* Kernel messages to userspace */
 #define NETLINK_GENERIC		16
 /* leave room for NETLINK_DM (DM Events) */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/nfc.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/nfc.h
@@ -263,7 +263,7 @@
 #define NFC_SE_ENABLED  0x1
 
 struct sockaddr_nfc {
-	sa_family_t sa_family;
+	__kernel_sa_family_t sa_family;
 	__u32 dev_idx;
 	__u32 target_idx;
 	__u32 nfc_protocol;
@@ -271,14 +271,14 @@
 
 #define NFC_LLCP_MAX_SERVICE_NAME 63
 struct sockaddr_nfc_llcp {
-	sa_family_t sa_family;
+	__kernel_sa_family_t sa_family;
 	__u32 dev_idx;
 	__u32 target_idx;
 	__u32 nfc_protocol;
 	__u8 dsap; /* Destination SAP, if known */
 	__u8 ssap; /* Source SAP to be bound to */
 	char service_name[NFC_LLCP_MAX_SERVICE_NAME]; /* Service name URI */;
-	size_t service_name_len;
+	__kernel_size_t service_name_len;
 };
 
 /* NFC socket protocols */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/omap3isp.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/omap3isp.h
@@ -162,6 +162,7 @@
  * struct omap3isp_stat_data - Statistic data sent to or received from user
  * @ts: Timestamp of returned framestats.
  * @buf: Pointer to pass to user.
+ * @buf_size: Size of buffer.
  * @frame_number: Frame number of requested stats.
  * @cur_frame: Current frame number being processed.
  * @config_counter: Number of the configuration associated with the data.
@@ -176,10 +177,12 @@
 	struct timeval ts;
 #endif
 	void __user *buf;
-	__u32 buf_size;
-	__u16 frame_number;
-	__u16 cur_frame;
-	__u16 config_counter;
+	__struct_group(/* no tag */, frame, /* no attrs */,
+		__u32 buf_size;
+		__u16 frame_number;
+		__u16 cur_frame;
+		__u16 config_counter;
+	);
 };
 
 #ifdef __KERNEL__
@@ -189,10 +192,12 @@
 		__s32	tv_usec;
 	} ts;
 	__u32 buf;
-	__u32 buf_size;
-	__u16 frame_number;
-	__u16 cur_frame;
-	__u16 config_counter;
+	__struct_group(/* no tag */, frame, /* no attrs */,
+		__u32 buf_size;
+		__u16 frame_number;
+		__u16 cur_frame;
+		__u16 config_counter;
+	);
 };
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/pci_regs.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/pci_regs.h
@@ -504,6 +504,12 @@
 #define  PCI_EXP_DEVCTL_URRE	0x0008	/* Unsupported Request Reporting En. */
 #define  PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */
 #define  PCI_EXP_DEVCTL_PAYLOAD	0x00e0	/* Max_Payload_Size */
+#define  PCI_EXP_DEVCTL_PAYLOAD_128B 0x0000 /* 128 Bytes */
+#define  PCI_EXP_DEVCTL_PAYLOAD_256B 0x0020 /* 256 Bytes */
+#define  PCI_EXP_DEVCTL_PAYLOAD_512B 0x0040 /* 512 Bytes */
+#define  PCI_EXP_DEVCTL_PAYLOAD_1024B 0x0060 /* 1024 Bytes */
+#define  PCI_EXP_DEVCTL_PAYLOAD_2048B 0x0080 /* 2048 Bytes */
+#define  PCI_EXP_DEVCTL_PAYLOAD_4096B 0x00a0 /* 4096 Bytes */
 #define  PCI_EXP_DEVCTL_EXT_TAG	0x0100	/* Extended Tag Field Enable */
 #define  PCI_EXP_DEVCTL_PHANTOM	0x0200	/* Phantom Functions Enable */
 #define  PCI_EXP_DEVCTL_AUX_PME	0x0400	/* Auxiliary Power PM Enable */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/perf_event.h
@@ -251,6 +251,8 @@
 	PERF_BR_SYSRET		= 8,	/* syscall return */
 	PERF_BR_COND_CALL	= 9,	/* conditional function call */
 	PERF_BR_COND_RET	= 10,	/* conditional function return */
+	PERF_BR_ERET		= 11,	/* exception return */
+	PERF_BR_IRQ		= 12,	/* irq */
 	PERF_BR_MAX,
 };
 
@@ -299,6 +301,7 @@
  *	  { u64		time_enabled; } && PERF_FORMAT_TOTAL_TIME_ENABLED
  *	  { u64		time_running; } && PERF_FORMAT_TOTAL_TIME_RUNNING
  *	  { u64		id;           } && PERF_FORMAT_ID
+ *	  { u64		lost;         } && PERF_FORMAT_LOST
  *	} && !PERF_FORMAT_GROUP
  *
  *	{ u64		nr;
@@ -306,6 +309,7 @@
  *	  { u64		time_running; } && PERF_FORMAT_TOTAL_TIME_RUNNING
  *	  { u64		value;
  *	    { u64	id;           } && PERF_FORMAT_ID
+ *	    { u64	lost;         } && PERF_FORMAT_LOST
  *	  }		cntr[nr];
  *	} && PERF_FORMAT_GROUP
  * };
@@ -315,8 +319,9 @@
 	PERF_FORMAT_TOTAL_TIME_RUNNING		= 1U << 1,
 	PERF_FORMAT_ID				= 1U << 2,
 	PERF_FORMAT_GROUP			= 1U << 3,
+	PERF_FORMAT_LOST			= 1U << 4,
 
-	PERF_FORMAT_MAX = 1U << 4,		/* non-ABI */
+	PERF_FORMAT_MAX = 1U << 5,		/* non-ABI */
 };
 
 #define PERF_ATTR_SIZE_VER0	64	/* sizeof first published struct */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/rseq.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/rseq.h
@@ -105,23 +105,11 @@
 	 * Read and set by the kernel. Set by user-space with single-copy
 	 * atomicity semantics. This field should only be updated by the
 	 * thread which registered this data structure. Aligned on 64-bit.
+	 *
+	 * 32-bit architectures should update the low order bits of the
+	 * rseq_cs field, leaving the high order bits initialized to 0.
 	 */
-	union {
-		__u64 ptr64;
-#ifdef __LP64__
-		__u64 ptr;
-#else
-		struct {
-#if (defined(__BYTE_ORDER) && (__BYTE_ORDER == __BIG_ENDIAN)) || defined(__BIG_ENDIAN)
-			__u32 padding;		/* Initialized to zero. */
-			__u32 ptr32;
-#else /* LITTLE */
-			__u32 ptr32;
-			__u32 padding;		/* Initialized to zero. */
-#endif /* ENDIAN */
-		} ptr;
-#endif
-	} rseq_cs;
+	__u64 rseq_cs;
 
 	/*
 	 * Restartable sequences flags field.
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/rtnetlink.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/rtnetlink.h
@@ -172,7 +172,7 @@
 #define RTM_GETLINKPROP	RTM_GETLINKPROP
 
 	RTM_NEWVLAN = 112,
-#define RTM_NEWNVLAN	RTM_NEWVLAN
+#define RTM_NEWVLAN	RTM_NEWVLAN
 	RTM_DELVLAN,
 #define RTM_DELVLAN	RTM_DELVLAN
 	RTM_GETVLAN,
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/seg6_iptunnel.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/seg6_iptunnel.h
@@ -35,6 +35,8 @@
 	SEG6_IPTUN_MODE_INLINE,
 	SEG6_IPTUN_MODE_ENCAP,
 	SEG6_IPTUN_MODE_L2ENCAP,
+	SEG6_IPTUN_MODE_ENCAP_RED,
+	SEG6_IPTUN_MODE_L2ENCAP_RED,
 };
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/serial_core.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/serial_core.h
@@ -68,6 +68,9 @@
 /* NVIDIA Tegra Combined UART */
 #define PORT_TEGRA_TCU	41
 
+/* ASPEED AST2x00 virtual UART */
+#define PORT_ASPEED_VUART	42
+
 /* Intel EG20 */
 #define PORT_PCH_8LINE	44
 #define PORT_PCH_2LINE	45
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/smc.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/smc.h
@@ -38,6 +38,9 @@
 #define SMC_GENL_FAMILY_VERSION		1
 
 #define SMC_PCI_ID_STR_LEN		16 /* Max length of pci id string */
+#define SMC_MAX_HOSTNAME_LEN		32 /* Max length of the hostname */
+#define SMC_MAX_UEID			4  /* Max number of user EIDs */
+#define SMC_MAX_EID_LEN			32 /* Max length of an EID */
 
 /* SMC_GENL_FAMILY commands */
 enum {
@@ -49,6 +52,13 @@
 	SMC_NETLINK_GET_DEV_SMCR,
 	SMC_NETLINK_GET_STATS,
 	SMC_NETLINK_GET_FBACK_STATS,
+	SMC_NETLINK_DUMP_UEID,
+	SMC_NETLINK_ADD_UEID,
+	SMC_NETLINK_REMOVE_UEID,
+	SMC_NETLINK_FLUSH_UEID,
+	SMC_NETLINK_DUMP_SEID,
+	SMC_NETLINK_ENABLE_SEID,
+	SMC_NETLINK_DISABLE_SEID,
 };
 
 /* SMC_GENL_FAMILY top level attributes */
@@ -74,17 +84,28 @@
 	SMC_NLA_SYS_IS_ISM_V2,		/* u8 */
 	SMC_NLA_SYS_LOCAL_HOST,		/* string */
 	SMC_NLA_SYS_SEID,		/* string */
+	SMC_NLA_SYS_IS_SMCR_V2,		/* u8 */
 	__SMC_NLA_SYS_MAX,
 	SMC_NLA_SYS_MAX = __SMC_NLA_SYS_MAX - 1
 };
 
-/* SMC_NLA_LGR_V2 nested attributes */
+/* SMC_NLA_LGR_D_V2_COMMON and SMC_NLA_LGR_R_V2_COMMON nested attributes */
 enum {
 	SMC_NLA_LGR_V2_VER,		/* u8 */
 	SMC_NLA_LGR_V2_REL,		/* u8 */
 	SMC_NLA_LGR_V2_OS,		/* u8 */
 	SMC_NLA_LGR_V2_NEG_EID,		/* string */
 	SMC_NLA_LGR_V2_PEER_HOST,	/* string */
+	__SMC_NLA_LGR_V2_MAX,
+	SMC_NLA_LGR_V2_MAX = __SMC_NLA_LGR_V2_MAX - 1
+};
+
+/* SMC_NLA_LGR_R_V2 nested attributes */
+enum {
+	SMC_NLA_LGR_R_V2_UNSPEC,
+	SMC_NLA_LGR_R_V2_DIRECT,	/* u8 */
+	__SMC_NLA_LGR_R_V2_MAX,
+	SMC_NLA_LGR_R_V2_MAX = __SMC_NLA_LGR_R_V2_MAX - 1
 };
 
 /* SMC_GEN_LGR_SMCR attributes */
@@ -96,6 +117,8 @@
 	SMC_NLA_LGR_R_PNETID,		/* string */
 	SMC_NLA_LGR_R_VLAN_ID,		/* u8 */
 	SMC_NLA_LGR_R_CONNS_NUM,	/* u32 */
+	SMC_NLA_LGR_R_V2_COMMON,	/* nest */
+	SMC_NLA_LGR_R_V2,		/* nest */
 	__SMC_NLA_LGR_R_MAX,
 	SMC_NLA_LGR_R_MAX = __SMC_NLA_LGR_R_MAX - 1
 };
@@ -128,7 +151,7 @@
 	SMC_NLA_LGR_D_PNETID,		/* string */
 	SMC_NLA_LGR_D_CHID,		/* u16 */
 	SMC_NLA_LGR_D_PAD,		/* flag */
-	SMC_NLA_LGR_V2,			/* nest */
+	SMC_NLA_LGR_D_V2_COMMON,	/* nest */
 	__SMC_NLA_LGR_D_MAX,
 	SMC_NLA_LGR_D_MAX = __SMC_NLA_LGR_D_MAX - 1
 };
@@ -242,4 +265,21 @@
 	__SMC_NLA_FBACK_STATS_MAX,
 	SMC_NLA_FBACK_STATS_MAX = __SMC_NLA_FBACK_STATS_MAX - 1
 };
+
+/* SMC_NETLINK_UEID attributes */
+enum {
+	SMC_NLA_EID_TABLE_UNSPEC,
+	SMC_NLA_EID_TABLE_ENTRY,	/* string */
+	__SMC_NLA_EID_TABLE_MAX,
+	SMC_NLA_EID_TABLE_MAX = __SMC_NLA_EID_TABLE_MAX - 1
+};
+
+/* SMC_NETLINK_SEID attributes */
+enum {
+	SMC_NLA_SEID_UNSPEC,
+	SMC_NLA_SEID_ENTRY,	/* string */
+	SMC_NLA_SEID_ENABLED,	/* u8 */
+	__SMC_NLA_SEID_TABLE_MAX,
+	SMC_NLA_SEID_TABLE_MAX = __SMC_NLA_SEID_TABLE_MAX - 1
+};
 #endif /* _UAPI_LINUX_SMC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/stddef.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/stddef.h
@@ -1,6 +1,47 @@
 /* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _UAPI_LINUX_STDDEF_H
+#define _UAPI_LINUX_STDDEF_H
+
 #include <linux/compiler_types.h>
 
 #ifndef __always_inline
 #define __always_inline inline
 #endif
+
+/**
+ * __struct_group() - Create a mirrored named and anonyomous struct
+ *
+ * @TAG: The tag name for the named sub-struct (usually empty)
+ * @NAME: The identifier name of the mirrored sub-struct
+ * @ATTRS: Any struct attributes (usually empty)
+ * @MEMBERS: The member declarations for the mirrored structs
+ *
+ * Used to create an anonymous union of two structs with identical layout
+ * and size: one anonymous and one named. The former's members can be used
+ * normally without sub-struct naming, and the latter can be used to
+ * reason about the start, end, and size of the group of struct members.
+ * The named struct can also be explicitly tagged for layer reuse, as well
+ * as both having struct attributes appended.
+ */
+#define __struct_group(TAG, NAME, ATTRS, MEMBERS...) \
+	union { \
+		struct { MEMBERS } ATTRS; \
+		struct TAG { MEMBERS } ATTRS NAME; \
+	} ATTRS
+
+/**
+ * __DECLARE_FLEX_ARRAY() - Declare a flexible array usable in a union
+ *
+ * @TYPE: The type of each flexible array element
+ * @NAME: The name of the flexible array member
+ *
+ * In order to have a flexible array member in a union or alone in a
+ * struct, it needs to be wrapped in an anonymous struct with at least 1
+ * named member, but that member can be empty.
+ */
+#define __DECLARE_FLEX_ARRAY(TYPE, NAME)	\
+	struct { \
+		struct { } __empty_ ## NAME; \
+		TYPE NAME[]; \
+	}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/swab.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/swab.h
@@ -3,7 +3,7 @@
 #define _UAPI_LINUX_SWAB_H
 
 #include <linux/types.h>
-#include <linux/compiler.h>
+#include <linux/stddef.h>
 #include <asm/bitsperlong.h>
 #include <asm/swab.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/sync_file.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/sync_file.h
@@ -52,7 +52,7 @@
  * @name:	name of fence
  * @status:	status of fence. 1: signaled 0:active <0:error
  * @flags:	sync_file_info flags
- * @num_fences	number of fences in the sync_file
+ * @num_fences:	number of fences in the sync_file
  * @pad:	padding for 64-bit alignment, should always be zero
  * @sync_fence_info: pointer to array of structs sync_fence_info with all
  *		 fences in the sync_file
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/sysctl.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/sysctl.h
@@ -153,7 +153,7 @@
 	KERN_NMI_WATCHDOG=75, /* int: enable/disable nmi watchdog */
 	KERN_PANIC_ON_NMI=76, /* int: whether we will panic on an unrecovered */
 	KERN_PANIC_ON_WARN=77, /* int: call panic() in WARN() functions */
-	KERN_PANIC_PRINT=78, /* ulong: bitmask to print system info on panic */
+	KERN_PANIC_PRINT=78, /* unsigned long: bitmask to print system info on panic */
 };
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/tty_flags.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/tty_flags.h
@@ -32,6 +32,7 @@
 #define ASYNCB_AUTOPROBE	15 /* [x] Port was autoprobed by PCI/PNP code */
 #define ASYNCB_MAGIC_MULTIPLIER	16 /* Use special CLK or divisor */
 #define ASYNCB_LAST_USER	16
+#define ASYNCB_INITIALIZED	31 /* Serial port was initialized */
 
 /*
  * Internal flags used only by kernel (read-only)
@@ -40,7 +41,6 @@
  *	    TTY_PORT_ flags in the iflags field (and not userspace-visible)
  */
 #ifndef __KERNEL__
-#define ASYNCB_INITIALIZED	31 /* Serial port was initialized */
 #define ASYNCB_SUSPENDED	30 /* Serial port is suspended */
 #define ASYNCB_NORMAL_ACTIVE	29 /* Normal device is active */
 #define ASYNCB_BOOT_AUTOCONF	28 /* Autoconfigure port on bootup */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/uio/uio.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/uio/uio.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * The header for UIO driver
+ *
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
+ */
+
+#ifndef _UAPI_UIO_UIO_H_
+#define _UAPI_UIO_UIO_H_
+
+#include <linux/ioctl.h>
+#include <linux/types.h>
+
+/**
+ * enum uio_dmabuf_dir - list of dma directions for mapping management
+ * @UIO_DMABUF_DIR_BIDIR: Bidirectional DMA. To and from device
+ * @UIO_DMABUF_DIR_TO_DEV: DMA to device
+ * @UIO_DMABUF_DIR_FROM_DEV: DMA from device
+ * @UIO_DMABUF_DIR_NONE: Direction not specified
+ */
+enum uio_dmabuf_dir {
+	UIO_DMABUF_DIR_BIDIR	= 1,
+	UIO_DMABUF_DIR_TO_DEV	= 2,
+	UIO_DMABUF_DIR_FROM_DEV	= 3,
+	UIO_DMABUF_DIR_NONE	= 4,
+};
+
+/**
+ * struct uio_dmabuf_args - arguments from userspace to map / unmap dmabuf
+ * @dbuf_fd: The fd or dma buf
+ * @dma_addr: The dma address of dmabuf @dbuf_fd
+ * @size: The size of dmabuf @dbuf_fd
+ * @dir: direction of dma transfer of dmabuf @dbuf_fd
+ */
+struct uio_dmabuf_args {
+	__s32	dbuf_fd;
+	__u64	dma_addr;
+	__u64	size;
+	__u8	dir;
+};
+
+#define UIO_IOC_BASE		'U'
+
+/**
+ * DOC: UIO_IOC_MAP_DMABUF - Map the dma buf to userspace uio application
+ *
+ * This takes uio_dmabuf_args, and maps the given dmabuf @dbuf_fd and returns
+ * information to userspace.
+ * FIXME: This is experimental and may change at any time. Don't consider this
+ * as stable ABI.
+ */
+#define	UIO_IOC_MAP_DMABUF	_IOWR(UIO_IOC_BASE, 0x1, struct uio_dmabuf_args)
+
+/**
+ * DOC: UIO_IOC_UNMAP_DMABUF - Unmap the dma buf
+ *
+ * This takes uio_dmabuf_args, and unmaps the previous mapped dmabuf @dbuf_fd.
+ * FIXME: This is experimental and may change at any time. Don't consider this
+ * as stable ABI.
+ */
+#define	UIO_IOC_UNMAP_DMABUF	_IOWR(UIO_IOC_BASE, 0x2, struct uio_dmabuf_args)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/usb/video.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/usb/video.h
@@ -179,6 +179,36 @@
 #define UVC_CONTROL_CAP_AUTOUPDATE			(1 << 3)
 #define UVC_CONTROL_CAP_ASYNCHRONOUS			(1 << 4)
 
+/* 3.9.2.6 Color Matching Descriptor Values */
+enum uvc_color_primaries_values {
+	UVC_COLOR_PRIMARIES_UNSPECIFIED,
+	UVC_COLOR_PRIMARIES_BT_709_SRGB,
+	UVC_COLOR_PRIMARIES_BT_470_2_M,
+	UVC_COLOR_PRIMARIES_BT_470_2_B_G,
+	UVC_COLOR_PRIMARIES_SMPTE_170M,
+	UVC_COLOR_PRIMARIES_SMPTE_240M,
+};
+
+enum uvc_transfer_characteristics_values {
+	UVC_TRANSFER_CHARACTERISTICS_UNSPECIFIED,
+	UVC_TRANSFER_CHARACTERISTICS_BT_709,
+	UVC_TRANSFER_CHARACTERISTICS_BT_470_2_M,
+	UVC_TRANSFER_CHARACTERISTICS_BT_470_2_B_G,
+	UVC_TRANSFER_CHARACTERISTICS_SMPTE_170M,
+	UVC_TRANSFER_CHARACTERISTICS_SMPTE_240M,
+	UVC_TRANSFER_CHARACTERISTICS_LINEAR,
+	UVC_TRANSFER_CHARACTERISTICS_SRGB,
+};
+
+enum uvc_matrix_coefficients {
+	UVC_MATRIX_COEFFICIENTS_UNSPECIFIED,
+	UVC_MATRIX_COEFFICIENTS_BT_709,
+	UVC_MATRIX_COEFFICIENTS_FCC,
+	UVC_MATRIX_COEFFICIENTS_BT_470_2_B_G,
+	UVC_MATRIX_COEFFICIENTS_SMPTE_170M,
+	UVC_MATRIX_COEFFICIENTS_SMPTE_240M,
+};
+
 /* ------------------------------------------------------------------------
  * UVC structures
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/uvcvideo.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/uvcvideo.h
@@ -86,7 +86,7 @@
  * struct. The first two fields are added by the driver, they can be used for
  * clock synchronisation. The rest is an exact copy of a UVC payload header.
  * Only complete objects with complete buffers are included. Therefore it's
- * always sizeof(meta->ts) + sizeof(meta->sof) + meta->length bytes large.
+ * always sizeof(meta->ns) + sizeof(meta->sof) + meta->length bytes large.
  */
 struct uvc_meta_buf {
 	__u64 ns;
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/v4l2-mediabus.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/v4l2-mediabus.h
@@ -79,6 +79,8 @@
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(RGB888_2X12_BE),
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(RGB888_2X12_LE),
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(ARGB8888_1X32),
+	V4L2_MBUS_FROM_MEDIA_BUS_FMT(RBG888_1X24),
+	V4L2_MBUS_FROM_MEDIA_BUS_FMT(RGB888_1X32_PADHI),
 
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(Y8_1X8),
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(UV8_1X8),
@@ -115,6 +117,7 @@
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(VYUY12_1X24),
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(YUYV12_1X24),
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(YVYU12_1X24),
+	V4L2_MBUS_FROM_MEDIA_BUS_FMT(VUY8_1X24),
 
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(SBGGR8_1X8),
 	V4L2_MBUS_FROM_MEDIA_BUS_FMT(SGBRG8_1X8),
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/v4l2-subdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/v4l2-subdev.h
@@ -188,6 +188,26 @@
 /* The v4l2 sub-device video device node is registered in read-only mode. */
 #define V4L2_SUBDEV_CAP_RO_SUBDEV		0x00000001
 
+/**
+ * struct v4l2_subdev_route - A signal route inside a subdev
+ * @sink: the sink pad
+ * @source: the source pad
+ */
+struct v4l2_subdev_route {
+	__u32 sink;
+	__u32 source;
+};
+
+/**
+ * struct v4l2_subdev_routing - Routing information
+ * @num_routes: the total number of routes in the routes array
+ * @routes: the routes array
+ */
+struct v4l2_subdev_routing {
+	__u32 num_routes;
+	struct v4l2_subdev_route *routes;
+};
+
 /* Backwards compatibility define --- to be removed */
 #define v4l2_subdev_edid v4l2_edid
 
@@ -215,5 +235,7 @@
 #define VIDIOC_SUBDEV_ENUM_DV_TIMINGS		_IOWR('V', 98, struct v4l2_enum_dv_timings)
 #define VIDIOC_SUBDEV_QUERY_DV_TIMINGS		_IOR('V', 99, struct v4l2_dv_timings)
 #define VIDIOC_SUBDEV_DV_TIMINGS_CAP		_IOWR('V', 100, struct v4l2_dv_timings_cap)
+#define VIDIOC_SUBDEV_G_ROUTING			_IOWR('V', 38, struct v4l2_subdev_routing)
+#define VIDIOC_SUBDEV_S_ROUTING			_IOWR('V', 39, struct v4l2_subdev_routing)
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/vfio_zdev.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/vfio_zdev.h
@@ -29,6 +29,9 @@
 	__u16 fmb_length;	/* Measurement Block Length (in bytes) */
 	__u8 pft;		/* PCI Function Type */
 	__u8 gid;		/* PCI function group ID */
+	/* End of version 1 */
+	__u32 fh;		/* PCI function handle */
+	/* End of version 2 */
 };
 
 /**
@@ -47,6 +50,10 @@
 	__u16 noi;		/* Maximum number of MSIs */
 	__u16 maxstbl;		/* Maximum Store Block Length */
 	__u8 version;		/* Supported PCI Version */
+	/* End of version 1 */
+	__u8 reserved;
+	__u16 imaxstbl;		/* Maximum Interpreted Store Block Length */
+	/* End of version 2 */
 };
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/videodev2.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/videodev2.h
@@ -283,6 +283,7 @@
 	V4L2_XFER_FUNC_NONE        = 5,
 	V4L2_XFER_FUNC_DCI_P3      = 6,
 	V4L2_XFER_FUNC_SMPTE2084   = 7,
+	V4L2_XFER_FUNC_HLG         = 8,
 };
 
 /*
@@ -555,13 +556,18 @@
 #define V4L2_PIX_FMT_RGBX32  v4l2_fourcc('X', 'B', '2', '4') /* 32  RGBX-8-8-8-8  */
 #define V4L2_PIX_FMT_ARGB32  v4l2_fourcc('B', 'A', '2', '4') /* 32  ARGB-8-8-8-8  */
 #define V4L2_PIX_FMT_XRGB32  v4l2_fourcc('B', 'X', '2', '4') /* 32  XRGB-8-8-8-8  */
+#define V4L2_PIX_FMT_XBGR30  v4l2_fourcc('R', 'X', '3', '0') /* 32  XBGR-2-10-10-10 */
+#define V4L2_PIX_FMT_XBGR40  v4l2_fourcc('R', 'X', '4', '0') /* 40  XBGR-4-12-12-12 */
+#define V4L2_PIX_FMT_BGR48   v4l2_fourcc('R', 'G', '4', '8') /* 32  BGR-16-16-16 */
 
 /* Grey formats */
 #define V4L2_PIX_FMT_GREY    v4l2_fourcc('G', 'R', 'E', 'Y') /*  8  Greyscale     */
 #define V4L2_PIX_FMT_Y4      v4l2_fourcc('Y', '0', '4', ' ') /*  4  Greyscale     */
 #define V4L2_PIX_FMT_Y6      v4l2_fourcc('Y', '0', '6', ' ') /*  6  Greyscale     */
 #define V4L2_PIX_FMT_Y10     v4l2_fourcc('Y', '1', '0', ' ') /* 10  Greyscale     */
+#define V4L2_PIX_FMT_XY10    v4l2_fourcc('X', 'Y', '1', '0') /* 10  Greyscale 2-10-10-10 */
 #define V4L2_PIX_FMT_Y12     v4l2_fourcc('Y', '1', '2', ' ') /* 12  Greyscale     */
+#define V4L2_PIX_FMT_XY12    v4l2_fourcc('X', 'Y', '1', '2') /* 12  Greyscale 4-12-12-12 */
 #define V4L2_PIX_FMT_Y14     v4l2_fourcc('Y', '1', '4', ' ') /* 14  Greyscale     */
 #define V4L2_PIX_FMT_Y16     v4l2_fourcc('Y', '1', '6', ' ') /* 16  Greyscale     */
 #define V4L2_PIX_FMT_Y16_BE  v4l2_fourcc_be('Y', '1', '6', ' ') /* 16  Greyscale BE  */
@@ -584,6 +590,9 @@
 #define V4L2_PIX_FMT_VYUY    v4l2_fourcc('V', 'Y', 'U', 'Y') /* 16  YUV 4:2:2     */
 #define V4L2_PIX_FMT_Y41P    v4l2_fourcc('Y', '4', '1', 'P') /* 12  YUV 4:1:1     */
 #define V4L2_PIX_FMT_YUV444  v4l2_fourcc('Y', '4', '4', '4') /* 16  xxxxyyyy uuuuvvvv */
+#define V4L2_PIX_FMT_XVUY32  v4l2_fourcc('X', 'V', '3', '2') /* 32  XVUY 8:8:8:8 */
+#define V4L2_PIX_FMT_AVUY32  v4l2_fourcc('A', 'V', '3', '2') /* 32  AVUY 8:8:8:8 */
+#define V4L2_PIX_FMT_VUY24   v4l2_fourcc('V', 'U', '2', '4') /* 24  VUY 8:8:8 */
 #define V4L2_PIX_FMT_YUV555  v4l2_fourcc('Y', 'U', 'V', 'O') /* 16  YUV-5-5-5     */
 #define V4L2_PIX_FMT_YUV565  v4l2_fourcc('Y', 'U', 'V', 'P') /* 16  YUV-5-6-5     */
 #define V4L2_PIX_FMT_YUV24   v4l2_fourcc('Y', 'U', 'V', '3') /* 24  YUV-8-8-8     */
@@ -593,6 +602,7 @@
 #define V4L2_PIX_FMT_VUYA32  v4l2_fourcc('V', 'U', 'Y', 'A') /* 32  VUYA-8-8-8-8  */
 #define V4L2_PIX_FMT_VUYX32  v4l2_fourcc('V', 'U', 'Y', 'X') /* 32  VUYX-8-8-8-8  */
 #define V4L2_PIX_FMT_M420    v4l2_fourcc('M', '4', '2', '0') /* 12  YUV 4:2:0 2 lines y, 1 line uv interleaved */
+#define V4L2_PIX_FMT_XVUY10  v4l2_fourcc('X', '4', '1', '0') /* 32  XVUY 2-10-10-10 */
 
 /* two planes -- one Y, one Cr + Cb interleaved  */
 #define V4L2_PIX_FMT_NV12    v4l2_fourcc('N', 'V', '1', '2') /* 12  Y/CbCr 4:2:0  */
@@ -601,6 +611,14 @@
 #define V4L2_PIX_FMT_NV61    v4l2_fourcc('N', 'V', '6', '1') /* 16  Y/CrCb 4:2:2  */
 #define V4L2_PIX_FMT_NV24    v4l2_fourcc('N', 'V', '2', '4') /* 24  Y/CbCr 4:4:4  */
 #define V4L2_PIX_FMT_NV42    v4l2_fourcc('N', 'V', '4', '2') /* 24  Y/CrCb 4:4:4  */
+#define V4L2_PIX_FMT_XV20    v4l2_fourcc('X', 'V', '2', '0') /* 32  XY/UV 4:2:2 10-bit */
+#define V4L2_PIX_FMT_XV15    v4l2_fourcc('X', 'V', '1', '5') /* 32  XY/UV 4:2:0 10-bit */
+#define V4L2_PIX_FMT_X012    v4l2_fourcc('X', '0', '1', '2') /* 40  XY/UV 4:2:0 12-bit 4-12-12-12 */
+#define V4L2_PIX_FMT_X212    v4l2_fourcc('X', '2', '1', '2') /* 40  XY/UV 4:2:2 12-bit 4-12-12-12 */
+#define V4L2_PIX_FMT_X412    v4l2_fourcc('X', '4', '1', '2') /* 40  XY/UV 4:4:4 12-bit 4-12-12-12 */
+#define V4L2_PIX_FMT_X016    v4l2_fourcc('X', '0', '1', '6') /* 32  XY/UV 4:2:0 16-bit */
+#define V4L2_PIX_FMT_X216    v4l2_fourcc('X', '2', '1', '6') /* 32  XY/UV 4:2:2 16-bit */
+#define V4L2_PIX_FMT_X416    v4l2_fourcc('X', '4', '1', '6') /* 32  XY/UV 4:4:4 16-bit */
 #define V4L2_PIX_FMT_HM12    v4l2_fourcc('H', 'M', '1', '2') /*  8  YUV 4:2:0 16x16 macroblocks */
 
 /* two non contiguous planes - one Y, one Cr + Cb interleaved  */
@@ -609,6 +627,14 @@
 #define V4L2_PIX_FMT_NV16M   v4l2_fourcc('N', 'M', '1', '6') /* 16  Y/CbCr 4:2:2  */
 #define V4L2_PIX_FMT_NV61M   v4l2_fourcc('N', 'M', '6', '1') /* 16  Y/CrCb 4:2:2  */
 #define V4L2_PIX_FMT_NV12MT  v4l2_fourcc('T', 'M', '1', '2') /* 12  Y/CbCr 4:2:0 64x32 macroblocks */
+#define V4L2_PIX_FMT_XV20M   v4l2_fourcc('X', 'M', '2', '0') /* 32  XY/UV 4:2:2 10-bit */
+#define V4L2_PIX_FMT_XV15M   v4l2_fourcc('X', 'M', '1', '5') /* 32  XY/UV 4:2:0 10-bit */
+#define V4L2_PIX_FMT_X012M   v4l2_fourcc('M', '0', '1', '2') /* 40  XY/UV 4:2:0 12-bit 4-12-12-12 */
+#define V4L2_PIX_FMT_X212M   v4l2_fourcc('M', '2', '1', '2') /* 40  XY/UV 4:2:2 12-bit 4-12-12-12 */
+#define V4L2_PIX_FMT_X412M   v4l2_fourcc('M', '4', '1', '2') /* 40  XY/UV 4:4:4 12-bit 4-12-12-12 */
+#define V4L2_PIX_FMT_X016M   v4l2_fourcc('M', '0', '1', '6') /* 32  XY/UV 4:2:0 16-bit */
+#define V4L2_PIX_FMT_X216M   v4l2_fourcc('M', '2', '1', '6') /* 32  XY/UV 4:2:2 16-bit */
+#define V4L2_PIX_FMT_X416M   v4l2_fourcc('M', '4', '1', '6') /* 32  XY/UV 4:4:4 16-bit */
 #define V4L2_PIX_FMT_NV12MT_16X16 v4l2_fourcc('V', 'M', '1', '2') /* 12  Y/CbCr 4:2:0 16x16 macroblocks */
 
 /* three planes - Y Cb, Cr */
@@ -618,6 +644,8 @@
 #define V4L2_PIX_FMT_YUV420  v4l2_fourcc('Y', 'U', '1', '2') /* 12  YUV 4:2:0     */
 #define V4L2_PIX_FMT_YVU420  v4l2_fourcc('Y', 'V', '1', '2') /* 12  YVU 4:2:0     */
 #define V4L2_PIX_FMT_YUV422P v4l2_fourcc('4', '2', '2', 'P') /* 16  YVU422 planar */
+#define V4L2_PIX_FMT_YUV444P v4l2_fourcc('4', '4', '4', 'P') /* 24  YUV444 planar */
+#define V4L2_PIX_FMT_X403    v4l2_fourcc('X', '4', '0', '3') /* 32  XYUV 4:4:4 10-bit */
 
 /* three non contiguous planes - Y, Cb, Cr */
 #define V4L2_PIX_FMT_YUV420M v4l2_fourcc('Y', 'M', '1', '2') /* 12  YUV420 planar */
@@ -1560,7 +1588,8 @@
 	((bt)->width + V4L2_DV_BT_BLANKING_WIDTH(bt))
 #define V4L2_DV_BT_BLANKING_HEIGHT(bt) \
 	((bt)->vfrontporch + (bt)->vsync + (bt)->vbackporch + \
-	 (bt)->il_vfrontporch + (bt)->il_vsync + (bt)->il_vbackporch)
+	 ((bt)->interlaced ? \
+	  ((bt)->il_vfrontporch + (bt)->il_vsync + (bt)->il_vbackporch) : 0))
 #define V4L2_DV_BT_FRAME_HEIGHT(bt) \
 	((bt)->height + V4L2_DV_BT_BLANKING_HEIGHT(bt))
 
@@ -1651,7 +1680,7 @@
 	__u8	     name[32];		/*  Label */
 	__u32	     type;		/*  Type of input */
 	__u32	     audioset;		/*  Associated audios (bitfield) */
-	__u32        tuner;             /*  enum v4l2_tuner_type */
+	__u32        tuner;             /*  Tuner index */
 	v4l2_std_id  std;
 	__u32	     status;
 	__u32	     capabilities;
@@ -1814,6 +1843,8 @@
 	V4L2_CTRL_TYPE_MPEG2_QUANTISATION   = 0x0250,
 	V4L2_CTRL_TYPE_MPEG2_SEQUENCE       = 0x0251,
 	V4L2_CTRL_TYPE_MPEG2_PICTURE        = 0x0252,
+
+	V4L2_CTRL_TYPE_HDR	     = 0x0400,
 };
 
 /*  Used in the VIDIOC_QUERYCTRL ioctl for querying controls */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/virtio_ids.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/virtio_ids.h
@@ -73,12 +73,12 @@
  * Virtio Transitional IDs
  */
 
-#define VIRTIO_TRANS_ID_NET		1000 /* transitional virtio net */
-#define VIRTIO_TRANS_ID_BLOCK		1001 /* transitional virtio block */
-#define VIRTIO_TRANS_ID_BALLOON		1002 /* transitional virtio balloon */
-#define VIRTIO_TRANS_ID_CONSOLE		1003 /* transitional virtio console */
-#define VIRTIO_TRANS_ID_SCSI		1004 /* transitional virtio SCSI */
-#define VIRTIO_TRANS_ID_RNG		1005 /* transitional virtio rng */
-#define VIRTIO_TRANS_ID_9P		1009 /* transitional virtio 9p console */
+#define VIRTIO_TRANS_ID_NET		0x1000 /* transitional virtio net */
+#define VIRTIO_TRANS_ID_BLOCK		0x1001 /* transitional virtio block */
+#define VIRTIO_TRANS_ID_BALLOON		0x1002 /* transitional virtio balloon */
+#define VIRTIO_TRANS_ID_CONSOLE		0x1003 /* transitional virtio console */
+#define VIRTIO_TRANS_ID_SCSI		0x1004 /* transitional virtio SCSI */
+#define VIRTIO_TRANS_ID_RNG		0x1005 /* transitional virtio rng */
+#define VIRTIO_TRANS_ID_9P		0x1009 /* transitional virtio 9p console */
 
 #endif /* _LINUX_VIRTIO_IDS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xfrm.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xfrm.h
@@ -313,6 +313,7 @@
 	XFRMA_SET_MARK,		/* __u32 */
 	XFRMA_SET_MARK_MASK,	/* __u32 */
 	XFRMA_IF_ID,		/* __u32 */
+	XFRMA_MTIMER_THRESH,	/* __u32 in seconds for input SA */
 	__XFRMA_MAX
 
 #define XFRMA_OUTPUT_MARK XFRMA_SET_MARK	/* Compatibility */
@@ -510,6 +511,12 @@
 	int				ifindex;
 	__u8				flags;
 };
+/* This flag was exposed without any kernel code that supporting it.
+ * Unfortunately, strongswan has the code that uses sets this flag,
+ * which makes impossible to reuse this bit.
+ *
+ * So leave it here to make sure that it won't be reused by mistake.
+ */
 #define XFRM_OFFLOAD_IPV6	1
 #define XFRM_OFFLOAD_INBOUND	2
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xilinx-hls.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xilinx-hls.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+
+#ifndef __UAPI_XILINX_HLS_H__
+#define __UAPI_XILINX_HLS_H__
+
+#include <linux/ioctl.h>
+#include <linux/types.h>
+#include <linux/videodev2.h>
+
+struct xilinx_axi_hls_register {
+	__u32 offset;
+	__u32 value;
+};
+
+struct xilinx_axi_hls_registers {
+	__u32 num_regs;
+	struct xilinx_axi_hls_register *regs;
+};
+
+#define XILINX_AXI_HLS_READ	_IOWR('V', BASE_VIDIOC_PRIVATE+0, struct xilinx_axi_hls_registers)
+#define XILINX_AXI_HLS_WRITE	_IOW('V', BASE_VIDIOC_PRIVATE+1, struct xilinx_axi_hls_registers)
+
+#endif /* __UAPI_XILINX_HLS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xilinx-sdirxss.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xilinx-sdirxss.h
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+
+#ifndef __UAPI_XILINX_SDIRXSS_H__
+#define __UAPI_XILINX_SDIRXSS_H__
+
+#include <linux/types.h>
+#include <linux/videodev2.h>
+
+/*
+ * Events
+ *
+ * V4L2_EVENT_XLNXSDIRX_UNDERFLOW: Video in to AXI4 Stream core underflowed
+ * V4L2_EVENT_XLNXSDIRX_OVERFLOW: Video in to AXI4 Stream core overflowed
+ */
+#define V4L2_EVENT_XLNXSDIRX_CLASS	(V4L2_EVENT_PRIVATE_START | 0x200)
+#define V4L2_EVENT_XLNXSDIRX_UNDERFLOW	(V4L2_EVENT_XLNXSDIRX_CLASS | 0x1)
+#define V4L2_EVENT_XLNXSDIRX_OVERFLOW	(V4L2_EVENT_XLNXSDIRX_CLASS | 0x2)
+
+/*
+ * This enum is used to prepare the bitmask
+ * of modes to be detected
+ */
+enum {
+	XSDIRX_MODE_SD_OFFSET = 0,
+	XSDIRX_MODE_HD_OFFSET,
+	XSDIRX_MODE_3G_OFFSET,
+	XSDIRX_MODE_6G_OFFSET,
+	XSDIRX_MODE_12GI_OFFSET,
+	XSDIRX_MODE_12GF_OFFSET,
+	XSDIRX_MODE_NUM_SUPPORTED,
+};
+
+#define XSDIRX_DETECT_ALL_MODES		(BIT(XSDIRX_MODE_SD_OFFSET) | \
+					BIT(XSDIRX_MODE_HD_OFFSET) | \
+					BIT(XSDIRX_MODE_3G_OFFSET) | \
+					BIT(XSDIRX_MODE_6G_OFFSET) | \
+					BIT(XSDIRX_MODE_12GI_OFFSET) | \
+					BIT(XSDIRX_MODE_12GF_OFFSET))
+
+/*
+ * EDH Error Types
+ * ANC - Ancillary Data Packet Errors
+ * FF - Full Field Errors
+ * AP - Active Portion Errors
+ */
+
+#define XSDIRX_EDH_ERRCNT_ANC_EDH_ERR	BIT(0)
+#define XSDIRX_EDH_ERRCNT_ANC_EDA_ERR	BIT(1)
+#define XSDIRX_EDH_ERRCNT_ANC_IDH_ERR	BIT(2)
+#define XSDIRX_EDH_ERRCNT_ANC_IDA_ERR	BIT(3)
+#define XSDIRX_EDH_ERRCNT_ANC_UES_ERR	BIT(4)
+#define XSDIRX_EDH_ERRCNT_FF_EDH_ERR	BIT(5)
+#define XSDIRX_EDH_ERRCNT_FF_EDA_ERR	BIT(6)
+#define XSDIRX_EDH_ERRCNT_FF_IDH_ERR	BIT(7)
+#define XSDIRX_EDH_ERRCNT_FF_IDA_ERR	BIT(8)
+#define XSDIRX_EDH_ERRCNT_FF_UES_ERR	BIT(9)
+#define XSDIRX_EDH_ERRCNT_AP_EDH_ERR	BIT(10)
+#define XSDIRX_EDH_ERRCNT_AP_EDA_ERR	BIT(11)
+#define XSDIRX_EDH_ERRCNT_AP_IDH_ERR	BIT(12)
+#define XSDIRX_EDH_ERRCNT_AP_IDA_ERR	BIT(13)
+#define XSDIRX_EDH_ERRCNT_AP_UES_ERR	BIT(14)
+#define XSDIRX_EDH_ERRCNT_PKT_CHKSUM_ERR	BIT(15)
+
+#define XSDIRX_EDH_ALLERR_MASK		0xFFFF
+
+#endif /* __UAPI_XILINX_SDIRXSS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xilinx-v4l2-controls.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xilinx-v4l2-controls.h
@@ -70,5 +70,152 @@
 #define V4L2_CID_XILINX_TPG_STUCK_PIXEL_THRESH	(V4L2_CID_XILINX_TPG + 16)
 /* Noise level */
 #define V4L2_CID_XILINX_TPG_NOISE_GAIN		(V4L2_CID_XILINX_TPG + 17)
+/* Foreground pattern (HLS)*/
+#define V4L2_CID_XILINX_TPG_HLS_FG_PATTERN     (V4L2_CID_XILINX_TPG + 18)
 
+/*
+ * Xilinx CRESAMPLE Video IP
+ */
+
+#define V4L2_CID_XILINX_CRESAMPLE		(V4L2_CID_USER_BASE + 0xc020)
+
+/* The field parity for interlaced video */
+#define V4L2_CID_XILINX_CRESAMPLE_FIELD_PARITY	(V4L2_CID_XILINX_CRESAMPLE + 1)
+/* Specify if the first line of video contains the Chroma information */
+#define V4L2_CID_XILINX_CRESAMPLE_CHROMA_PARITY	(V4L2_CID_XILINX_CRESAMPLE + 2)
+
+/*
+ * Xilinx RGB2YUV Video IPs
+ */
+
+#define V4L2_CID_XILINX_RGB2YUV			(V4L2_CID_USER_BASE + 0xc040)
+
+/* Maximum Luma(Y) value */
+#define V4L2_CID_XILINX_RGB2YUV_YMAX		(V4L2_CID_XILINX_RGB2YUV + 1)
+/* Minimum Luma(Y) value */
+#define V4L2_CID_XILINX_RGB2YUV_YMIN		(V4L2_CID_XILINX_RGB2YUV + 2)
+/* Maximum Cb Chroma value */
+#define V4L2_CID_XILINX_RGB2YUV_CBMAX		(V4L2_CID_XILINX_RGB2YUV + 3)
+/* Minimum Cb Chroma value */
+#define V4L2_CID_XILINX_RGB2YUV_CBMIN		(V4L2_CID_XILINX_RGB2YUV + 4)
+/* Maximum Cr Chroma value */
+#define V4L2_CID_XILINX_RGB2YUV_CRMAX		(V4L2_CID_XILINX_RGB2YUV + 5)
+/* Minimum Cr Chroma value */
+#define V4L2_CID_XILINX_RGB2YUV_CRMIN		(V4L2_CID_XILINX_RGB2YUV + 6)
+/* The offset compensation value for Luma(Y) */
+#define V4L2_CID_XILINX_RGB2YUV_YOFFSET		(V4L2_CID_XILINX_RGB2YUV + 7)
+/* The offset compensation value for Cb Chroma */
+#define V4L2_CID_XILINX_RGB2YUV_CBOFFSET	(V4L2_CID_XILINX_RGB2YUV + 8)
+/* The offset compensation value for Cr Chroma */
+#define V4L2_CID_XILINX_RGB2YUV_CROFFSET	(V4L2_CID_XILINX_RGB2YUV + 9)
+
+/* Y = CA * R + (1 - CA - CB) * G + CB * B */
+
+/* CA coefficient */
+#define V4L2_CID_XILINX_RGB2YUV_ACOEF		(V4L2_CID_XILINX_RGB2YUV + 10)
+/* CB coefficient */
+#define V4L2_CID_XILINX_RGB2YUV_BCOEF		(V4L2_CID_XILINX_RGB2YUV + 11)
+/* CC coefficient */
+#define V4L2_CID_XILINX_RGB2YUV_CCOEF		(V4L2_CID_XILINX_RGB2YUV + 12)
+/* CD coefficient */
+#define V4L2_CID_XILINX_RGB2YUV_DCOEF		(V4L2_CID_XILINX_RGB2YUV + 13)
+
+/*
+ * Xilinx HLS Video IP
+ */
+
+#define V4L2_CID_XILINX_HLS			(V4L2_CID_USER_BASE + 0xc060)
+
+/* The IP model */
+#define V4L2_CID_XILINX_HLS_MODEL		(V4L2_CID_XILINX_HLS + 1)
+
+/*
+ * Xilinx Gamma Correction IP
+ */
+
+/* Base ID */
+#define V4L2_CID_XILINX_GAMMA_CORR		(V4L2_CID_USER_BASE + 0xc0c0)
+/* Adjust Red Gamma */
+#define V4L2_CID_XILINX_GAMMA_CORR_RED_GAMMA	(V4L2_CID_XILINX_GAMMA_CORR + 1)
+/* Adjust Blue Gamma */
+#define V4L2_CID_XILINX_GAMMA_CORR_BLUE_GAMMA	(V4L2_CID_XILINX_GAMMA_CORR + 2)
+/* Adjust Green Gamma */
+#define V4L2_CID_XILINX_GAMMA_CORR_GREEN_GAMMA	(V4L2_CID_XILINX_GAMMA_CORR + 3)
+
+/*
+ * Xilinx Color Space Converter (CSC) VPSS
+ */
+
+/* Base ID */
+#define V4L2_CID_XILINX_CSC			(V4L2_CID_USER_BASE + 0xc0a0)
+/* Adjust Brightness */
+#define V4L2_CID_XILINX_CSC_BRIGHTNESS		(V4L2_CID_XILINX_CSC + 1)
+/* Adjust Contrast */
+#define V4L2_CID_XILINX_CSC_CONTRAST		(V4L2_CID_XILINX_CSC + 2)
+/* Adjust Red Gain */
+#define V4L2_CID_XILINX_CSC_RED_GAIN		(V4L2_CID_XILINX_CSC + 3)
+/* Adjust Green Gain */
+#define V4L2_CID_XILINX_CSC_GREEN_GAIN		(V4L2_CID_XILINX_CSC + 4)
+/* Adjust Blue Gain */
+#define V4L2_CID_XILINX_CSC_BLUE_GAIN		(V4L2_CID_XILINX_CSC + 5)
+
+/*
+ * Xilinx SDI Rx Subsystem
+ */
+
+/* Base ID */
+#define V4L2_CID_XILINX_SDIRX			(V4L2_CID_USER_BASE + 0xc100)
+
+/* Framer Control */
+#define V4L2_CID_XILINX_SDIRX_FRAMER		(V4L2_CID_XILINX_SDIRX + 1)
+/* Video Lock Window Control */
+#define V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW	(V4L2_CID_XILINX_SDIRX + 2)
+/* EDH Error Mask Control */
+#define V4L2_CID_XILINX_SDIRX_EDH_ERRCNT_ENABLE	(V4L2_CID_XILINX_SDIRX + 3)
+/* Mode search Control */
+#define V4L2_CID_XILINX_SDIRX_SEARCH_MODES	(V4L2_CID_XILINX_SDIRX + 4)
+/* Get Detected Mode control */
+#define V4L2_CID_XILINX_SDIRX_MODE_DETECT	(V4L2_CID_XILINX_SDIRX + 5)
+/* Get CRC error status */
+#define V4L2_CID_XILINX_SDIRX_CRC		(V4L2_CID_XILINX_SDIRX + 6)
+/* Get EDH error count control */
+#define V4L2_CID_XILINX_SDIRX_EDH_ERRCNT	(V4L2_CID_XILINX_SDIRX + 7)
+/* Get EDH status control */
+#define V4L2_CID_XILINX_SDIRX_EDH_STATUS	(V4L2_CID_XILINX_SDIRX + 8)
+/* Get Transport Interlaced status */
+#define V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED	(V4L2_CID_XILINX_SDIRX + 9)
+/* Get Active Streams count */
+#define V4L2_CID_XILINX_SDIRX_ACTIVE_STREAMS	(V4L2_CID_XILINX_SDIRX + 10)
+/* Is Mode 3GB */
+#define V4L2_CID_XILINX_SDIRX_IS_3GB		(V4L2_CID_XILINX_SDIRX + 11)
+
+/*
+ * Xilinx VIP
+ */
+
+/* Base ID */
+#define V4L2_CID_XILINX_VIP			(V4L2_CID_USER_BASE + 0xc120)
+
+/* Low latency mode */
+#define V4L2_CID_XILINX_LOW_LATENCY		(V4L2_CID_XILINX_VIP + 1)
+
+/* Control values to enable/disable low latency capture mode */
+#define XVIP_LOW_LATENCY_ENABLE		BIT(1)
+#define XVIP_LOW_LATENCY_DISABLE	BIT(2)
+
+/* Control value to start DMA */
+#define XVIP_START_DMA			BIT(3)
+
+/*
+ * Xilinx SCD
+ */
+
+/* Base ID */
+#define V4L2_CID_XILINX_SCD			(V4L2_CID_USER_BASE + 0xc140)
+
+/*
+ * SCD Threshold
+ * User can pass percentage as an integer to tune threshold value
+ */
+#define V4L2_CID_XILINX_SCD_THRESHOLD		(V4L2_CID_XILINX_SCD + 1)
 #endif /* __UAPI_XILINX_V4L2_CONTROLS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xilinx-v4l2-events.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xilinx-v4l2-events.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+
+/*
+ * Xilinx V4L2 SCD Driver
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *
+ */
+
+#ifndef __UAPI_XILINX_V4L2_EVENTS_H__
+#define __UAPI_XILINX_V4L2_EVENTS_H__
+
+#include <linux/videodev2.h>
+
+/*
+ * Events
+ *
+ * V4L2_EVENT_XLNXSCD: Scene Change Detection
+ */
+#define V4L2_EVENT_XLNXSCD_CLASS	(V4L2_EVENT_PRIVATE_START | 0x300)
+#define V4L2_EVENT_XLNXSCD		(V4L2_EVENT_XLNXSCD_CLASS | 0x1)
+
+#endif /* __UAPI_XILINX_V4L2_EVENTS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xlnx-ai-engine.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xlnx-ai-engine.h
@@ -0,0 +1,573 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Copyright (c) 2020, Xilinx Inc.
+ */
+
+#ifndef _UAPI_AI_ENGINE_H_
+#define _UAPI_AI_ENGINE_H_
+
+#ifndef __KERNEL__
+#include <stdlib.h>
+#endif
+
+#include <linux/ioctl.h>
+#include <linux/types.h>
+
+enum aie_reg_op {
+	AIE_REG_WRITE,
+	AIE_REG_BLOCKWRITE,
+	AIE_REG_BLOCKSET,
+};
+
+/**
+ * enum aie_module_type - identifies different hardware modules within a
+ *			  tile type. AIE tile may have memory and core
+ *			  module. While a PL or shim tile may have PL module.
+ * @AIE_MEM_MOD: comprises of the following sub-modules,
+ *			* data memory.
+ *			* tile DMA.
+ *			* lock module.
+ *			* events, event broadcast and event actions.
+ *			* tracing and profiling.
+ * @AIE_CORE_MOD: comprises of the following sub-modules,
+ *			* AIE core.
+ *			* program Memory.
+ *			* events, event broadcast and event actions.
+ *			* tracing and profiling.
+ *			* AXI-MM and AXI-S tile interconnects.
+ * @AIE_PL_MOD: comprises of the following sub-modules,
+ *			* PL interface.
+ *			* AXI-MM and AXI-S tile interconnects.
+ *			* Level 1 interrupt controllers.
+ *			* events, event broadcast and event actions.
+ *			* tracing and profiling.
+ * @AIE_NOC_MOD: comprises of the following sub-modules,
+ *			* interface from NoC Slave Unit (NSU)
+ *			  (bridge to AXI-MM switch)
+ *			* interfaces to NoC NoC Master Unit (NMU)
+ *				* shim DMA & locks
+ *				* NoC stream interface
+ */
+enum aie_module_type {
+	AIE_MEM_MOD,
+	AIE_CORE_MOD,
+	AIE_PL_MOD,
+	AIE_NOC_MOD,
+};
+
+/**
+ * enum aie_rsc_type - defines AI engine hardware resource types
+ * @AIE_RSCTYPE_PERF: perfcounter resource
+ * @AIE_RSCTYPE_USEREVENT: user events resource
+ * @AIE_RSCTYPE_TRACECONTROL: trace controller resource
+ * @AIE_RSCTYPE_PCEVENT: PC events resource
+ * @AIE_RSCTYPE_SSSELECT: stream switch port select resource
+ * @AIE_RSCTYPE_BROADCAST: broadcast events resource
+ * @AIE_RSCTYPE_COMBOEVENT: combo events resource
+ * @AIE_RSCTYPE_GROUPEVENTS: group events resource
+ * @AIE_RSCTYPE_MAX: total number of resources
+ */
+enum aie_rsc_type {
+	AIE_RSCTYPE_PERF,
+	AIE_RSCTYPE_USEREVENT,
+	AIE_RSCTYPE_TRACECONTROL,
+	AIE_RSCTYPE_PCEVENT,
+	AIE_RSCTYPE_SSSELECT,
+	AIE_RSCTYPE_BROADCAST,
+	AIE_RSCTYPE_COMBOEVENT,
+	AIE_RSCTYPE_GROUPEVENTS,
+	AIE_RSCTYPE_MAX
+};
+
+/**
+ * enum aie_part_status - defines AI engine partition status
+ * @XAIE_PART_STATUS_IDLE: partition is idle
+ * @XAIE_PART_STATUS_INUSE: partition is in use
+ * @XAIE_PART_STATUS_INVALID: partition is invalid to the system
+ *			      that is system cannot see the partition
+ */
+enum aie_part_status {
+	XAIE_PART_STATUS_IDLE,
+	XAIE_PART_STATUS_INUSE,
+	XAIE_PART_STATUS_INVALID,
+};
+
+/*
+ * AI engine partition control flags
+ */
+/* Not reset when release AI engine partition */
+#define XAIE_PART_NOT_RST_ON_RELEASE	0x00000001U
+
+/*
+ * AI engine resource property flags
+ */
+/*
+ * For resources which needs to be allocated contiguous
+ * such as combo events, it needs to be 0, 1; 2, 3;
+ * or 0, 1, 2, 3
+ */
+#define XAIE_RSC_PATTERN_BLOCK		(1U << 0)
+
+/* Any broadcast channel id */
+#define XAIE_BROADCAST_ID_ANY		0xFFFFFFFFU
+
+/* request a channel to broadcast to the whole partition */
+#define XAIE_BROADCAST_ALL		(1U << 0)
+
+/**
+ * struct aie_location - AIE location information
+ * @col: column id
+ * @row: row id
+ */
+struct aie_location {
+	__u32 col;
+	__u32 row;
+};
+
+/**
+ * struct aie_location_byte - AIE location information with single byte for
+ *			      column and row
+ * @row: row id
+ * @col: column id
+ *
+ * This structure follows the SSW AIE row and col sequence.
+ */
+struct aie_location_byte {
+	__u8 row;
+	__u8 col;
+};
+
+/**
+ * struct aie_range - AIE range information
+ * @start: start tile location
+ * @size: size of the range, number of columns and rows
+ */
+struct aie_range {
+	struct aie_location start;
+	struct aie_location size;
+};
+
+/**
+ * struct aie_mem - AIE memory information
+ * @range: range of tiles of the memory
+ * @offset: register offset within a tile of the memory
+ * @size: of a the memory in one tile
+ * @fd: file descriptor of the memory
+ */
+struct aie_mem {
+	struct aie_range range;
+	size_t offset;
+	size_t size;
+	int fd;
+};
+
+/**
+ * struct aie_mem_args - AIE memory enquiry arguments
+ * @num_mems: number of "struct aie_mem" elements
+ *	      e.g. two memory information elements, one for tile core memory,
+ *	      and the other for tile data memory.
+ * @mems: array of AI engine memory information elements
+ */
+struct aie_mem_args {
+	unsigned int num_mems;
+	struct aie_mem *mems;
+};
+
+/**
+ * struct aie_reg_args - AIE access register arguments
+ * @op: if this request is to read, write or poll register
+ * @mask: mask for mask write, 0 for not mask write
+ * @offset: offset of register to the start of an AI engine partition
+ * @val: value to write or get
+ * @dataptr: pointer to data buffer for block write
+ * @len: length of the buffer pointed by data
+ */
+struct aie_reg_args {
+	enum aie_reg_op op;
+	__u32 mask;
+	__u64 offset;
+	__u32 val;
+	__u64 dataptr;
+	__u32 len;
+};
+
+/**
+ * struct aie_range_args - AIE range request arguments
+ * @partition_id: partition id. It is used to identify the
+ *		  AI engine partition in the system.
+ * @uid: image identifier loaded on the AI engine partition
+ * @range: range of AIE tiles
+ * @status: indicate if the AI engine is in use.
+ *	    0 means not in used, otherwise, in use.
+ */
+struct aie_range_args {
+	__u32 partition_id;
+	__u32 uid;
+	struct aie_range range;
+	__u32 status;
+};
+
+/**
+ * struct aie_partition_query - AIE partition query arguments
+ * @partition_cnt: number of defined partitions in the system
+ * @partitions: buffer to store defined partitions information.
+ */
+struct aie_partition_query {
+	struct aie_range_args *partitions;
+	__u32 partition_cnt;
+};
+
+#define AIE_PART_ID_START_COL_SHIFT	0U
+#define AIE_PART_ID_NUM_COLS_SHIFT	8U
+#define AIE_PART_ID_START_COL_MASK	GENMASK(7, 0)
+#define AIE_PART_ID_NUM_COLS_MASK	GENMASK(15, 8)
+
+#define aie_part_id_get_val(part_id, F) \
+	(((part_id) & AIE_PART_ID_##F ##_MASK) >> AIE_PART_ID_##F ##_SHIFT)
+#define aie_part_id_get_start_col(part_id) \
+	aie_part_id_get_val((part_id), START_COL)
+#define aie_part_id_get_num_cols(part_id) \
+	aie_part_id_get_val((part_id), NUM_COLS)
+
+/**
+ * struct aie_partition_req - AIE request partition arguments
+ * @partition_id: partition node id. It is used to identify the AI engine
+ *		  partition. Its format is:
+ *		  Reserved_16bits | start_col_8bits | num_cols_8bits
+ * @uid: image identifier loaded on the AI engine partition
+ * @meta_data: meta data to indicate which resources used by application.
+ * @flag: used for application to indicate particular driver requirements
+ *	  application wants to have for the partition. e.g. do not clean
+ *	  resource when closing the partition.
+ */
+struct aie_partition_req {
+	__u32 partition_id;
+	__u32 uid;
+	__u64 meta_data;
+	__u32 flag;
+};
+
+/**
+ * struct aie_dma_bd_args - AIE DMA buffer descriptor information
+ * @bd: DMA buffer descriptor
+ * @data_va: virtual address of the data
+ * @loc: Tile location relative to the start of a partition
+ * @bd_id: buffer descriptor id
+ */
+struct aie_dma_bd_args {
+	__u32 *bd;
+	__u64 data_va;
+	struct aie_location loc;
+	__u32 bd_id;
+};
+
+/**
+ * struct aie_dmabuf_bd_args - AIE dmabuf buffer descriptor information
+ * @bd: DMA buffer descriptor, within the buffer descriptor, the address field
+ *	will be the offset to the start of the dmabuf
+ * @buf_fd: DMA buffer handler which is dmabuf file descriptor
+ * @loc: Tile location relative to the start of a partition
+ * @bd_id: buffer descriptor id
+ */
+struct aie_dmabuf_bd_args {
+	__u32 *bd;
+	struct aie_location loc;
+	int buf_fd;
+	__u32 bd_id;
+};
+
+/**
+ * struct aie_tiles_array - AIE tiles array
+ * @locs: tiles locations array
+ * @num_tiles: number of tiles in the tiles locations array
+ */
+struct aie_tiles_array {
+	struct aie_location *locs;
+	__u32 num_tiles;
+};
+
+/**
+ * struct aie_txn_inst - AIE transaction instance
+ * @num_cmds: number commands containing register ops
+ * @cmdsptr: pointer to the buffer containing register ops
+ */
+struct aie_txn_inst {
+	__u32 num_cmds;
+	__u64 cmdsptr;
+};
+
+/**
+ * struct aie_rsc_req - AIE resource request
+ * @loc: tile location
+ * @mod: module type
+ * @type: resource type
+ * @num_rscs: number of resource per request
+ * @flag: resource property, such as it needs to be in pattern block such as
+ *	  if @num_rscs is 2, it needs to be 0,1; 2,3, or 4,5
+ */
+struct aie_rsc_req {
+	struct aie_location loc;
+	__u32 mod;
+	__u32 type;
+	__u32 num_rscs;
+	__u8 flag;
+};
+
+/**
+ * struct aie_rsc - AIE resource properties
+ * @loc: tile location, single byte for column and row each
+ * @mod: module type
+ * @type: resource type
+ * @id: resource id
+ */
+struct aie_rsc {
+	struct aie_location_byte loc;
+	__u32 mod;
+	__u32 type;
+	__u32 id;
+};
+
+/**
+ * struct aie_rsc_req_rsp - AIE resource request and response structure
+ * @req: resource request per tile module
+ * @rscs: allocated resources array of `struct aie_rsc`
+ */
+struct aie_rsc_req_rsp {
+	struct aie_rsc_req req;
+	__u64 rscs;
+};
+
+/**
+ * struct aie_rsc_bc_req - AIE broadcast channel request
+ * @rscs: broadcast channel resource array for every module and every tile
+ *	  of the channel
+ * @num_rscs: number of expected broadcast channel resources on the path,
+ *	      it also indicates the number of expected modules on the path.
+ * @flag: user flag to indicate if it is to get a broadcast channel for the
+ *	  whole partition.
+ * @id: broadcast channel ID. XAIE_BROADCAST_ID_ANY, it means not particular
+ *	id is specified, driver will allocate a free one.
+ */
+struct aie_rsc_bc_req {
+	__u64 rscs;
+	__u32 num_rscs;
+	__u32 flag;
+	__u32 id;
+};
+
+/* AI engine resource statistics types */
+#define AIE_RSC_STAT_TYPE_STATIC	0U
+#define AIE_RSC_STAT_TYPE_AVAIL		1U
+#define AIE_RSC_STAT_TYPE_MAX		2U
+
+/**
+ * struct aie_rsc_user_stat - AIE user requested resource statistics
+ * @loc: tile location, single byte for column and row each
+ * @mod: module type
+ * @type: resource type
+ * @num_rscs: number of resources
+ */
+struct aie_rsc_user_stat {
+	struct aie_location_byte loc;
+	__u8 mod;
+	__u8 type;
+	__u8 num_rscs;
+} __attribute__((packed, aligned(4)));
+
+/**
+ * struct aie_rsc_user_stat_array - AIE user requested resource statistics array
+ * @stats: resource statistics array
+ * @num_stats: number of resource statistics elements
+ * @stats_type: resource statistics type
+ */
+struct aie_rsc_user_stat_array {
+	__u64 stats;
+	__u32 num_stats;
+	__u32 stats_type;
+};
+
+#define AIE_IOCTL_BASE 'A'
+
+/* AI engine device IOCTL operations */
+#define AIE_ENQUIRE_PART_IOCTL		_IOWR(AIE_IOCTL_BASE, 0x1, \
+					      struct aie_partition_query)
+#define AIE_REQUEST_PART_IOCTL		_IOR(AIE_IOCTL_BASE, 0x2, \
+					     struct aie_partition_req)
+
+/* AI engine partition IOCTL operations */
+#define AIE_REG_IOCTL			_IOWR(AIE_IOCTL_BASE, 0x8, \
+					      struct aie_reg_args)
+/**
+ * DOC: AIE_GET_MEM_IOCTL - enquire information of memories in the AI engine
+ *			    partition
+ * This ioctl is used to get the information of all the different types of
+ * memories in the AI engine partition. Application can get the memories
+ * information in two steps:
+ * 1. passing 0 as @num_mems in struct aie_mem_args to enquire the number of
+ *    different memories in the partition, the value will be returned in
+ *    @num_mems.
+ * 2. passing the number of memories in @num_mems and valid pointer as @mems of
+ *    struct aie_mem_args to store the details information of different
+ *    memories. The driver will create DMA buf for each type of memories, and
+ *    will return the memory addressing information along with the DMA buf file
+ *    descriptors in @mems.
+ * After getting the memories information, user can use mmap() with the DMA buf
+ * file descriptor to enable access the memories from userspace.
+ */
+#define AIE_GET_MEM_IOCTL		_IOWR(AIE_IOCTL_BASE, 0x9, \
+					      struct aie_mem_args)
+/**
+ * DOC: AIE_ATTACH_DMABUF_IOCTL - attach a dmabuf to AI engine partition
+ *
+ * This ioctl is used to attach a dmabuf to the AI engine partition. AI engine
+ * partition will return the number of scatter gather list elements of the
+ * dmabuf.
+ */
+#define AIE_ATTACH_DMABUF_IOCTL		_IOR(AIE_IOCTL_BASE, 0xa, int)
+
+/**
+ * DOC: AIE_DETACH_DMABUF_IOCTL - dettach a dmabuf from AI engine partition
+ *
+ * This ioctl is used to detach a dmabuf from the AI engine partition
+ */
+#define AIE_DETACH_DMABUF_IOCTL		_IOR(AIE_IOCTL_BASE, 0xb, int)
+
+/**
+ * DOC: AIE_SET_DMABUF_BD_IOCTL - set buffer descriptor to SHIM DMA
+ *
+ * This ioctl is used to set the buffer descriptor to SHIM DMA
+ */
+#define AIE_SET_SHIMDMA_BD_IOCTL	_IOW(AIE_IOCTL_BASE, 0xd, \
+					     struct aie_dma_bd_args)
+
+/**
+ * DOC: AIE_REQUEST_TILES_IOCTL - request AI engine tiles
+ *
+ * This ioctl is used to request tiles.
+ * When requested the AI engine partition, the kernel driver will scan the
+ * partition to track which tiles are enabled or not. After that, if user
+ * want to request for more tiles, it will use this ioctl to request more
+ * tiles.
+ * If the aie_tiles_array is empty, it means it will request for all tiles
+ * in the partition.
+ */
+#define AIE_REQUEST_TILES_IOCTL		_IOW(AIE_IOCTL_BASE, 0xe, \
+					     struct aie_tiles_array)
+
+/**
+ * DOC: AIE_RELEASE_TILES_IOCTL - release AI engine tiles
+ *
+ * This ioctl is used to release tiles
+ */
+#define AIE_RELEASE_TILES_IOCTL		_IOW(AIE_IOCTL_BASE, 0xf, \
+					     struct aie_tiles_array)
+
+/**
+ * DOC: AIE_SET_SHIMDMA_DMABUF_BD_IOCTL - set buffer descriptor which contains
+ *					  dmabuf to SHIM DMA
+ *
+ * This ioctl is used to set the buffer descriptor to SHIM DMA. The
+ * aie_dmabuf_bd_args contains the dmabuf fd and the buffer descriptor contents.
+ * The address field in the buffer descriptor contents should be the offset to
+ * the start of the dmabuf.
+ */
+#define AIE_SET_SHIMDMA_DMABUF_BD_IOCTL	_IOW(AIE_IOCTL_BASE, 0x10, \
+					     struct aie_dmabuf_bd_args)
+
+/**
+ * DOC: AIE_TRANSACTION_IOCTL - execute the register operations to
+ *					configure AIE partition
+ *
+ * This ioctl is used to perform multiple register operations like write,
+ * mask write, block set and block write on AIE partition. The aie_txn_inst
+ * contains the buffer with all the register operations required by the
+ * application.
+ */
+#define AIE_TRANSACTION_IOCTL		_IOWR(AIE_IOCTL_BASE, 0x11, \
+					     struct aie_txn_inst)
+
+/**
+ * DOC: AIE_RSC_REQ_IOCTL - request a type of resources of a tile
+ *
+ * This ioctl is used to request a type of resources of a tile of an AI engine
+ * partition.
+ * AI engine partitition driver will check if there are the requested number
+ * of resources available. If yes, fill in the allcoated resource IDs in the
+ * resources array provided by user.
+ */
+#define AIE_RSC_REQ_IOCTL		_IOW(AIE_IOCTL_BASE, 0x14, \
+					     struct aie_rsc_req_rsp)
+
+/**
+ * DOC: AIE_RSC_REQ_SPECIFIC_IOCTL - request statically allocated resource
+ *
+ * This ioctl is used to request to use a specified allcoated resource
+ * AI engine partitition driver will check if the resource has been allocated
+ * at compilation time. If yes, and no one else has requested it, it returns
+ * success.
+ */
+#define AIE_RSC_REQ_SPECIFIC_IOCTL	_IOW(AIE_IOCTL_BASE, 0x15, \
+					     struct aie_rsc)
+
+/**
+ * DOC: AIE_RSC_RELEASE_IOCTL - release allocated resource
+ *
+ * This ioctl is used to release a resource and returns it to the resource
+ * pool, so that next time if user want to request for a resource, it is
+ * available
+ */
+#define AIE_RSC_RELEASE_IOCTL		_IOW(AIE_IOCTL_BASE, 0x16, \
+					     struct aie_rsc)
+
+/**
+ * DOC: AIE_RSC_FREE_IOCTL - free allocated resource
+ *
+ * This ioctl is used to free an allocated resource. It will unmark the
+ * resource from runtime used. If the resource is allocated at compilation
+ * time, it will not be returned back to the resource pool.
+ */
+#define AIE_RSC_FREE_IOCTL		_IOW(AIE_IOCTL_BASE, 0x17, \
+					     struct aie_rsc)
+
+/**
+ * DOC: AIE_RSC_CHECK_AVAIL_IOCTL - check if resource is available
+ *
+ * This ioctl is used to check how many resources are available for a specified
+ * type of resource.
+ */
+#define AIE_RSC_CHECK_AVAIL_IOCTL	_IOW(AIE_IOCTL_BASE, 0x18, \
+					     struct aie_rsc_req)
+
+/**
+ * DOC: AIE_RSC_GET_COMMON_BROADCAST_IOCTL - get a common broadcast channel for
+ *					     the specified set of AI engine
+ *					     modules.
+ *
+ * This ioctl is used to get a common broadcast channel for the specified set
+ * of AI engine modules in the resources array. If the any of the input set of
+ * tiles is gated, it will return failure. This ioctl will not check the
+ * connection of the input modules set.
+ * The driver will fill in the resource ID with the assigned broadcast channel
+ * ID of the resources array.
+ * If the XAIE_BROADCAST_ALL is set in the request flag, it will get the
+ * broadcast channel for all the ungated tiles of the partition.
+ * If a particular broadcast channel id is specified in the request, if will
+ * check if the channel is available for the specified modules, or the whole
+ * partition depends on if XAIE_BROADCAST_ALL is set.
+ */
+#define AIE_RSC_GET_COMMON_BROADCAST_IOCTL	_IOW(AIE_IOCTL_BASE, 0x19, \
+						struct aie_rsc_bc_req)
+
+/**
+ * DOC: AIE_RSC_GET_STAT_IOCTL - get resource usage statistics
+ *
+ * This ioctl is used to get resource usage statistics. User passes an array of
+ * resource statistics requests and the resources statistics type that is if it
+ * is statically allocated or available resources. Each request specifies the
+ * tile, module type and the resource type. This ioctl returns the number of
+ * resources of the specified statistics type per request.
+ */
+#define AIE_RSC_GET_STAT_IOCTL		_IOW(AIE_IOCTL_BASE, 0x1a, \
+					struct aie_rsc_user_stat_array)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xlnx_mpg2tsmux_interface.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xlnx_mpg2tsmux_interface.h
@@ -0,0 +1,253 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+
+/*
+ * Xilinx mpeg2 transport stream muxer ioctl calls
+ *
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author:	Venkateshwar Rao G <venkateshwar.rao.gannava@xilinx.com>
+ */
+
+#ifndef __XLNX_MPG2TSMUX_INTERFACE_H__
+#define __XLNX_MPG2TSMUX_INTERFACE_H__
+
+#include <linux/types.h>
+#include <linux/ioctl.h>
+
+/**
+ * enum ts_mux_command - command for stream context
+ * @CREATE_TS_MISC: create misc
+ * @CREATE_TS_VIDEO_KEYFRAME: create video key frame
+ * @CREATE_TS_VIDEO_NON_KEYFRAME: create non key frame
+ * @CREATE_TS_AUDIO: create audio
+ * @WRITE_PAT: write pat
+ * @WRITE_PMT: write pmt
+ * @WRITE_SI: write si
+ * @INVALID: invalid
+ */
+enum ts_mux_command {
+	CREATE_TS_MISC = 0,
+	CREATE_TS_VIDEO_KEYFRAME,
+	CREATE_TS_VIDEO_NON_KEYFRAME,
+	CREATE_TS_AUDIO,
+	WRITE_PAT,
+	WRITE_PMT,
+	WRITE_SI,
+	INVALID
+};
+
+/**
+ * struct stream_context_in - struct to enqueue a stream context descriptor
+ * @command: stream context type
+ * @stream_id: stream identification number
+ * @extended_stream_id: extended stream id
+ * @is_pcr_stream: flag for pcr stream
+ * @is_valid_pts: flag for valid pts
+ * @is_valid_dts: flag for valid dts
+ * @is_dmabuf: flag to set if external src buffer is DMA allocated
+ * @pid: packet id number
+ * @size_data_in: size in bytes of input buffer
+ * @pts: presentation time stamp
+ * @dts: display time stamp
+ * @srcbuf_id: source buffer id after mmap
+ * @insert_pcr: flag for inserting pcr in stream context
+ * @pcr_extension: pcr extension number
+ * @pcr_base: pcr base number
+ */
+struct stream_context_in {
+	enum ts_mux_command command;
+	__u8 stream_id;
+	__u8 extended_stream_id;
+	int is_pcr_stream;
+	int is_valid_pts;
+	int is_valid_dts;
+	int is_dmabuf;
+	__u16 pid;
+	__u64 size_data_in;
+	__u64 pts;
+	__u64 dts;
+	__u32 srcbuf_id;
+	int insert_pcr;
+	__u16 pcr_extension;
+	__u64 pcr_base;
+};
+
+/**
+ * struct mux_context_in - struct to enqueue a mux context descriptor
+ * @is_dmabuf: flag to set if external src buffer is DMA allocated
+ * @dstbuf_id: destination buffer id after mmap
+ * @dmabuf_size: size in bytes of output buffer
+ */
+struct muxer_context_in {
+	int is_dmabuf;
+	__u32 dstbuf_id;
+	__u32 dmabuf_size;
+};
+
+/**
+ * enum xlnx_tsmux_status - ip status
+ * @MPG2MUX_BUSY: device busy
+ * @MPG2MUX_READY: device ready
+ * @MPG2MUX_ERROR: error state
+ */
+enum xlnx_tsmux_status {
+	MPG2MUX_BUSY = 0,
+	MPG2MUX_READY,
+	MPG2MUX_ERROR
+};
+
+/**
+ * struct strc_bufs_info - struct to specify bufs requirement
+ * @num_buf: number of buffers
+ * @buf_size: size of each buffer
+ */
+struct strc_bufs_info {
+	__u32 num_buf;
+	__u32 buf_size;
+};
+
+/**
+ * struct strc_out_buf - struct to get output buffer info
+ * @buf_id: buf id into which output is written
+ * @buf_write: output bytes written in buf
+ */
+struct out_buffer {
+	__u32 buf_id;
+	__u32 buf_write;
+};
+
+/**
+ * enum strmtbl_cnxt - streamid table operation
+ * @NO_UPDATE: no table update
+ * @ADD_TO_TBL: add the entry to table
+ * @DEL_FR_TBL: delete the entry from table
+ */
+enum strmtbl_cnxt {
+	NO_UPDATE = 0,
+	ADD_TO_TBL,
+	DEL_FR_TBL,
+};
+
+/**
+ * struct strm_tbl_info - struct to enqueue/dequeue streamid in table
+ * @strmtbl_ctxt: enqueue/dequeue stream id
+ * @pid: stream id
+ */
+struct strc_strminfo {
+	enum strmtbl_cnxt strmtbl_ctxt;
+	__u16 pid;
+};
+
+/**
+ * enum xlnx_tsmux_dma_dir - dma direction
+ * @DMA_TO_MPG2MUX: memory to device
+ * @DMA_FROM_MPG2MUX: device to memory
+ */
+enum xlnx_tsmux_dma_dir {
+	DMA_TO_MPG2MUX = 1,
+	DMA_FROM_MPG2MUX,
+};
+
+/**
+ * enum xlnx_tsmux_dmabuf_flags - dma buffer handling
+ * @DMABUF_ERROR: buffer error
+ * @DMABUF_CONTIG: contig buffer
+ * @DMABUF_NON_CONTIG: non contigs buffer
+ * @DMABUF_ATTACHED: buffer attached
+ */
+enum xlnx_tsmux_dmabuf_flags {
+	DMABUF_ERROR = 1,
+	DMABUF_CONTIG = 2,
+	DMABUF_NON_CONTIG = 4,
+	DMABUF_ATTACHED = 8,
+};
+
+/**
+ * struct xlnx_tsmux_dmabuf_info - struct to verify dma buf before enque
+ * @buf_fd: file descriptor
+ * @dir: direction of the dma buffer
+ * @flags: flags returned by the driver
+ */
+struct xlnx_tsmux_dmabuf_info {
+	int buf_fd;
+	enum xlnx_tsmux_dma_dir dir;
+	enum xlnx_tsmux_dmabuf_flags flags;
+};
+
+/* MPG2MUX IOCTL CALL LIST */
+
+#define MPG2MUX_MAGIC 'M'
+
+/**
+ * MPG2MUX_INBUFALLOC - src buffer allocation
+ */
+#define MPG2MUX_INBUFALLOC _IOWR(MPG2MUX_MAGIC, 1, struct strc_bufs_info *)
+
+/**
+ * MPG2MUX_INBUFDEALLOC - deallocates the all src buffers
+ */
+#define MPG2MUX_INBUFDEALLOC _IO(MPG2MUX_MAGIC, 2)
+
+/**
+ * MPG2MUX_OUTBUFALLOC - allocates DMA able memory for dst
+ */
+#define MPG2MUX_OUTBUFALLOC _IOWR(MPG2MUX_MAGIC, 3, struct strc_bufs_info *)
+
+/**
+ * MPG2MUX_OUTBUFDEALLOC - deallocates the all dst buffers allocated
+ */
+#define MPG2MUX_OUTBUFDEALLOC _IO(MPG2MUX_MAGIC, 4)
+
+/**
+ * MPG2MUX_STBLALLOC - allocates DMA able memory for streamid table
+ */
+#define MPG2MUX_STBLALLOC _IOW(MPG2MUX_MAGIC, 5, unsigned short *)
+
+/**
+ * MPG2MUX_STBLDEALLOC - deallocates streamid table memory
+ */
+#define MPG2MUX_STBLDEALLOC _IO(MPG2MUX_MAGIC, 6)
+
+/**
+ * MPG2MUX_TBLUPDATE - enqueue or dequeue in streamid table
+ */
+#define MPG2MUX_TBLUPDATE _IOW(MPG2MUX_MAGIC, 7, struct strc_strminfo *)
+
+/**
+ * MPG2MUX_SETSTRM - enqueue a stream descriptor in stream context
+ *		linked list along with src buf address
+ */
+#define MPG2MUX_SETSTRM _IOW(MPG2MUX_MAGIC, 8, struct stream_context_in *)
+
+/**
+ * MPG2MUX_START - starts muxer IP after configuring stream
+ *		and mux context registers
+ */
+#define MPG2MUX_START _IO(MPG2MUX_MAGIC, 9)
+
+/**
+ * MPG2MUX_STOP - stops the muxer IP
+ */
+#define MPG2MUX_STOP _IO(MPG2MUX_MAGIC, 10)
+
+/**
+ * MPG2MUX_STATUS - command to get the status of IP
+ */
+#define MPG2MUX_STATUS _IOR(MPG2MUX_MAGIC, 11, unsigned short *)
+
+/**
+ * MPG2MUX_GETOUTBUF - get the output buffer id with size of output data
+ */
+#define MPG2MUX_GETOUTBUF _IOW(MPG2MUX_MAGIC, 12, struct out_buffer *)
+
+/**
+ * MPG2MUX_SETMUX - enqueue a mux descriptor with dst buf address
+ */
+#define MPG2MUX_SETMUX _IOW(MPG2MUX_MAGIC, 13, struct muxer_context_in *)
+
+/**
+ * MPG2MUX_VRFY_DMABUF - status of a given dma buffer fd
+ */
+#define MPG2MUX_VDBUF _IOWR(MPG2MUX_MAGIC, 14, struct xlnx_tsmux_dmabuf_info *)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/xlnxsync.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/xlnxsync.h
@@ -0,0 +1,179 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+
+#ifndef __XLNXSYNC_H__
+#define __XLNXSYNC_H__
+
+#include <linux/types.h>
+
+#define XLNXSYNC_IOCTL_HDR_VER		0x10004
+
+/*
+ * This is set in the fb_id of struct xlnxsync_chan_config when
+ * configuring the channel. This makes the driver auto search for
+ * a free framebuffer slot.
+ */
+#define XLNXSYNC_AUTO_SEARCH		0xFF
+
+#define XLNXSYNC_MAX_ENC_CHAN		4
+#define XLNXSYNC_MAX_DEC_CHAN		2
+#define XLNXSYNC_BUF_PER_CHAN		3
+
+#define XLNXSYNC_PROD			0
+#define XLNXSYNC_CONS			1
+#define XLNXSYNC_IO			2
+
+#define XLNXSYNC_MAX_CORES		4
+
+/**
+ * struct xlnxsync_err_intr - Channel error interrupt types
+ * @prod_sync: Producer synchronization error interrupt
+ * @prod_wdg: Producer watchdog interrupt
+ * @cons_sync: Consumer synchronization error interrupt
+ * @cons_wdg: Consumer watchdog interrupt
+ * @ldiff: Luma buffer difference interrupt
+ * @cdiff: Chroma buffer difference interrupt
+ */
+struct xlnxsync_err_intr {
+	__u8 prod_sync : 1;
+	__u8 prod_wdg : 1;
+	__u8 cons_sync : 1;
+	__u8 cons_wdg : 1;
+	__u8 ldiff : 1;
+	__u8 cdiff : 1;
+};
+
+/**
+ * struct xlnxsync_intr - Channel Interrupt types
+ * @hdr_ver: IOCTL header version
+ * @err: Structure for error interrupts
+ * @prod_lfbdone: Producer luma frame buffer done interrupt
+ * @prod_cfbdone: Producer chroma frame buffer done interrupt
+ * @cons_lfbdone: Consumer luma frame buffer done interrupt
+ * @cons_cfbdone: Consumer chroma frame buffer done interrupt
+ */
+struct xlnxsync_intr {
+	__u64 hdr_ver;
+	struct xlnxsync_err_intr err;
+	__u8 prod_lfbdone : 1;
+	__u8 prod_cfbdone : 1;
+	__u8 cons_lfbdone : 1;
+	__u8 cons_cfbdone : 1;
+};
+
+/**
+ * struct xlnxsync_chan_config - Synchronizer channel configuration struct
+ * @hdr_ver: IOCTL header version
+ * @luma_start_offset: Start offset of Luma buffer
+ * @chroma_start_offset: Start offset of Chroma buffer
+ * @luma_end_offset: End offset of Luma buffer
+ * @chroma_end_offset: End offset of Chroma buffer
+ * @luma_margin: Margin for Luma buffer
+ * @chroma_margin: Margin for Chroma buffer
+ * @luma_core_offset: Array of 4 offsets for luma
+ * @chroma_core_offset: Array of 4 offsets for chroma
+ * @dma_fd: File descriptor of dma
+ * @fb_id: Framebuffer index. Valid values 0/1/2/XLNXSYNC_AUTO_SEARCH
+ * @ismono: Flag to indicate if buffer is Luma only.
+ * Valid 0..3 & XLNXSYNC_AUTO_SEARCH
+ *
+ * This structure contains the configuration for monitoring a particular
+ * framebuffer on a particular channel.
+ */
+struct xlnxsync_chan_config {
+	__u64 hdr_ver;
+	__u64 luma_start_offset[XLNXSYNC_IO];
+	__u64 chroma_start_offset[XLNXSYNC_IO];
+	__u64 luma_end_offset[XLNXSYNC_IO];
+	__u64 chroma_end_offset[XLNXSYNC_IO];
+	__u32 luma_margin;
+	__u32 chroma_margin;
+	__u32 luma_core_offset[XLNXSYNC_MAX_CORES];
+	__u32 chroma_core_offset[XLNXSYNC_MAX_CORES];
+	__u32 dma_fd;
+	__u8 fb_id[XLNXSYNC_IO];
+	__u8 ismono[XLNXSYNC_IO];
+};
+
+/**
+ * struct xlnxsync_clr_err - Clear channel error
+ * @hdr_ver: IOCTL header version
+ * @err: Structure for error interrupts
+ */
+struct xlnxsync_clr_err {
+	__u64 hdr_ver;
+	struct xlnxsync_err_intr err;
+};
+
+/**
+ * struct xlnxsync_fbdone - Framebuffer Done
+ * @hdr_ver: IOCTL header version
+ * @status: Framebuffer Done status
+ */
+struct xlnxsync_fbdone {
+	__u64 hdr_ver;
+	__u8 status[XLNXSYNC_BUF_PER_CHAN][XLNXSYNC_IO];
+};
+
+/**
+ * struct xlnxsync_config - Synchronizer IP configuration
+ * @hdr_ver: IOCTL header version
+ * @encode: true if encoder type, false for decoder type
+ * @max_channels: Maximum channels this IP supports
+ * @active_channels: Number of active IP channels
+ * @reserved_id: Reserved channel ID for instance
+ */
+struct xlnxsync_config {
+	__u64	hdr_ver;
+	__u8	encode;
+	__u8	max_channels;
+	__u8	active_channels;
+	__u8	reserved_id;
+	__u32	reserved[10];
+};
+
+/**
+ * struct xlnxsync_stat - Sync IP channel status
+ * @hdr_ver: IOCTL header version
+ * @fbdone: for every pair of luma/chroma buffer for every producer/consumer
+ * @enable: channel enable
+ * @err: Structure for error interrupts
+ */
+struct xlnxsync_stat {
+	__u64 hdr_ver;
+	__u8 fbdone[XLNXSYNC_BUF_PER_CHAN][XLNXSYNC_IO];
+	__u8 enable;
+	struct xlnxsync_err_intr err;
+};
+
+#define XLNXSYNC_MAGIC			'X'
+
+/*
+ * This ioctl is used to get the IP config (i.e. encode / decode)
+ * and max number of channels
+ */
+#define XLNXSYNC_GET_CFG		_IOR(XLNXSYNC_MAGIC, 1,\
+					     struct xlnxsync_config *)
+/* This ioctl is used to get the channel status */
+#define XLNXSYNC_CHAN_GET_STATUS	_IOR(XLNXSYNC_MAGIC, 2, __u32 *)
+/* This is used to set the framebuffer address for a channel */
+#define XLNXSYNC_CHAN_SET_CONFIG	_IOW(XLNXSYNC_MAGIC, 3,\
+					     struct xlnxsync_chan_config *)
+/* Enable a channel. */
+#define XLNXSYNC_CHAN_ENABLE		_IO(XLNXSYNC_MAGIC, 4)
+/* Disable a channel. */
+#define XLNXSYNC_CHAN_DISABLE		_IO(XLNXSYNC_MAGIC, 5)
+/* This is used to clear the Sync and Watchdog errors  for a channel */
+#define XLNXSYNC_CHAN_CLR_ERR		_IOW(XLNXSYNC_MAGIC, 6,\
+					     struct xlnxsync_clr_err *)
+/* This is used to get the framebuffer done status for a channel */
+#define XLNXSYNC_CHAN_GET_FBDONE_STAT	_IOR(XLNXSYNC_MAGIC, 7,\
+					     struct xlnxsync_fbdone *)
+/* This is used to clear the framebuffer done status for a channel */
+#define XLNXSYNC_CHAN_CLR_FBDONE_STAT	_IOW(XLNXSYNC_MAGIC, 8,\
+					     struct xlnxsync_fbdone *)
+/* This is used to set interrupt mask */
+#define XLNXSYNC_CHAN_SET_INTR_MASK	_IOW(XLNXSYNC_MAGIC, 9,\
+					     struct xlnxsync_intr *)
+/* This is used to reset the last programmed slot */
+#define XLNXSYNC_RESET_SLOT		_IO(XLNXSYNC_MAGIC, 10)
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/linux/zorro_ids.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/linux/zorro_ids.h
@@ -449,6 +449,9 @@
 #define  ZORRO_PROD_VMC_ISDN_BLASTER_Z2				ZORRO_ID(VMC, 0x01, 0)
 #define  ZORRO_PROD_VMC_HYPERCOM_4				ZORRO_ID(VMC, 0x02, 0)
 
+#define ZORRO_MANUF_CSLAB					0x1400
+#define  ZORRO_PROD_CSLAB_WARP_1260				ZORRO_ID(CSLAB, 0x65, 0)
+
 #define ZORRO_MANUF_INFORMATION					0x157C
 #define  ZORRO_PROD_INFORMATION_ISDN_ENGINE_I			ZORRO_ID(INFORMATION, 0x64, 0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/rdma/mlx5-abi.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/rdma/mlx5-abi.h
@@ -104,6 +104,7 @@
 	MLX5_IB_ALLOC_UCONTEXT_RESP_MASK_ECE               = 1UL << 2,
 	MLX5_IB_ALLOC_UCONTEXT_RESP_MASK_SQD2RTS           = 1UL << 3,
 	MLX5_IB_ALLOC_UCONTEXT_RESP_MASK_REAL_TIME_TS	   = 1UL << 4,
+	MLX5_IB_ALLOC_UCONTEXT_RESP_MASK_MKEY_UPDATE_TAG   = 1UL << 5,
 };
 
 enum mlx5_user_cmds_supp_uhw {
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/rdma/mlx5_user_ioctl_cmds.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/rdma/mlx5_user_ioctl_cmds.h
@@ -252,7 +252,7 @@
 	MLX5_IB_ATTR_QUERY_CONTEXT_RESP_UCTX = (1U << UVERBS_ID_NS_SHIFT),
 };
 
-#define MLX5_IB_DW_MATCH_PARAM 0x90
+#define MLX5_IB_DW_MATCH_PARAM 0xA0
 
 struct mlx5_ib_match_params {
 	__u32	match_params[MLX5_IB_DW_MATCH_PARAM];
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/scsi/scsi_bsg_mpi3mr.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/scsi/scsi_bsg_mpi3mr.h
@@ -0,0 +1,582 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later WITH Linux-syscall-note */
+/*
+ * Driver for Broadcom MPI3 Storage Controllers
+ *
+ * Copyright (C) 2017-2022 Broadcom Inc.
+ *  (mailto: mpi3mr-linuxdrv.pdl@broadcom.com)
+ *
+ */
+
+#ifndef SCSI_BSG_MPI3MR_H_INCLUDED
+#define SCSI_BSG_MPI3MR_H_INCLUDED
+
+#include <linux/types.h>
+
+/* Definitions for BSG commands */
+#define MPI3MR_IOCTL_VERSION			0x06
+
+#define MPI3MR_APP_DEFAULT_TIMEOUT		(60) /*seconds*/
+
+#define MPI3MR_BSG_ADPTYPE_UNKNOWN		0
+#define MPI3MR_BSG_ADPTYPE_AVGFAMILY		1
+
+#define MPI3MR_BSG_ADPSTATE_UNKNOWN		0
+#define MPI3MR_BSG_ADPSTATE_OPERATIONAL		1
+#define MPI3MR_BSG_ADPSTATE_FAULT		2
+#define MPI3MR_BSG_ADPSTATE_IN_RESET		3
+#define MPI3MR_BSG_ADPSTATE_UNRECOVERABLE	4
+
+#define MPI3MR_BSG_ADPRESET_UNKNOWN		0
+#define MPI3MR_BSG_ADPRESET_SOFT		1
+#define MPI3MR_BSG_ADPRESET_DIAG_FAULT		2
+
+#define MPI3MR_BSG_LOGDATA_MAX_ENTRIES		400
+#define MPI3MR_BSG_LOGDATA_ENTRY_HEADER_SZ	4
+
+#define MPI3MR_DRVBSG_OPCODE_UNKNOWN		0
+#define MPI3MR_DRVBSG_OPCODE_ADPINFO		1
+#define MPI3MR_DRVBSG_OPCODE_ADPRESET		2
+#define MPI3MR_DRVBSG_OPCODE_ALLTGTDEVINFO	4
+#define MPI3MR_DRVBSG_OPCODE_GETCHGCNT		5
+#define MPI3MR_DRVBSG_OPCODE_LOGDATAENABLE	6
+#define MPI3MR_DRVBSG_OPCODE_PELENABLE		7
+#define MPI3MR_DRVBSG_OPCODE_GETLOGDATA		8
+#define MPI3MR_DRVBSG_OPCODE_QUERY_HDB		9
+#define MPI3MR_DRVBSG_OPCODE_REPOST_HDB		10
+#define MPI3MR_DRVBSG_OPCODE_UPLOAD_HDB		11
+#define MPI3MR_DRVBSG_OPCODE_REFRESH_HDB_TRIGGERS	12
+
+
+#define MPI3MR_BSG_BUFTYPE_UNKNOWN		0
+#define MPI3MR_BSG_BUFTYPE_RAIDMGMT_CMD		1
+#define MPI3MR_BSG_BUFTYPE_RAIDMGMT_RESP	2
+#define MPI3MR_BSG_BUFTYPE_DATA_IN		3
+#define MPI3MR_BSG_BUFTYPE_DATA_OUT		4
+#define MPI3MR_BSG_BUFTYPE_MPI_REPLY		5
+#define MPI3MR_BSG_BUFTYPE_ERR_RESPONSE		6
+#define MPI3MR_BSG_BUFTYPE_MPI_REQUEST		0xFE
+
+#define MPI3MR_BSG_MPI_REPLY_BUFTYPE_UNKNOWN	0
+#define MPI3MR_BSG_MPI_REPLY_BUFTYPE_STATUS	1
+#define MPI3MR_BSG_MPI_REPLY_BUFTYPE_ADDRESS	2
+
+#define MPI3MR_HDB_BUFTYPE_UNKNOWN		0
+#define MPI3MR_HDB_BUFTYPE_TRACE		1
+#define MPI3MR_HDB_BUFTYPE_FIRMWARE		2
+#define MPI3MR_HDB_BUFTYPE_RESERVED		3
+
+#define MPI3MR_HDB_BUFSTATUS_UNKNOWN		0
+#define MPI3MR_HDB_BUFSTATUS_NOT_ALLOCATED	1
+#define MPI3MR_HDB_BUFSTATUS_POSTED_UNPAUSED	2
+#define MPI3MR_HDB_BUFSTATUS_POSTED_PAUSED	3
+#define MPI3MR_HDB_BUFSTATUS_RELEASED		4
+
+#define MPI3MR_HDB_TRIGGER_TYPE_UNKNOWN		0
+#define MPI3MR_HDB_TRIGGER_TYPE_DIAGFAULT	1
+#define MPI3MR_HDB_TRIGGER_TYPE_ELEMENT		2
+#define MPI3MR_HDB_TRIGGER_TYPE_MASTER		3
+
+
+/* Supported BSG commands */
+enum command {
+	MPI3MR_DRV_CMD = 1,
+	MPI3MR_MPT_CMD = 2,
+};
+
+/**
+ * struct mpi3_driver_info_layout - Information about driver
+ *
+ * @information_length: Length of this structure in bytes
+ * @driver_signature: Driver Vendor name
+ * @os_name: Operating System Name
+ * @driver_name: Driver name
+ * @driver_version: Driver version
+ * @driver_release_date: Driver release date
+ * @driver_capabilities: Driver capabilities
+ */
+struct mpi3_driver_info_layout {
+	__le32	information_length;
+	__u8	driver_signature[12];
+	__u8	os_name[16];
+	__u8	os_version[12];
+	__u8	driver_name[20];
+	__u8	driver_version[32];
+	__u8	driver_release_date[20];
+	__le32	driver_capabilities;
+};
+
+/**
+ * struct mpi3mr_bsg_in_adpinfo - Adapter information request
+ * data returned by the driver.
+ *
+ * @adp_type: Adapter type
+ * @rsvd1: Reserved
+ * @pci_dev_id: PCI device ID of the adapter
+ * @pci_dev_hw_rev: PCI revision of the adapter
+ * @pci_subsys_dev_id: PCI subsystem device ID of the adapter
+ * @pci_subsys_ven_id: PCI subsystem vendor ID of the adapter
+ * @pci_dev: PCI device
+ * @pci_func: PCI function
+ * @pci_bus: PCI bus
+ * @rsvd2: Reserved
+ * @pci_seg_id: PCI segment ID
+ * @app_intfc_ver: version of the application interface definition
+ * @rsvd3: Reserved
+ * @rsvd4: Reserved
+ * @rsvd5: Reserved
+ * @driver_info: Driver Information (Version/Name)
+ */
+struct mpi3mr_bsg_in_adpinfo {
+	__u32	adp_type;
+	__u32	rsvd1;
+	__u32	pci_dev_id;
+	__u32	pci_dev_hw_rev;
+	__u32	pci_subsys_dev_id;
+	__u32	pci_subsys_ven_id;
+	__u32	pci_dev:5;
+	__u32	pci_func:3;
+	__u32	pci_bus:8;
+	__u16	rsvd2;
+	__u32	pci_seg_id;
+	__u32	app_intfc_ver;
+	__u8	adp_state;
+	__u8	rsvd3;
+	__u16	rsvd4;
+	__u32	rsvd5[2];
+	struct mpi3_driver_info_layout driver_info;
+};
+
+/**
+ * struct mpi3mr_bsg_adp_reset - Adapter reset request
+ * payload data to the driver.
+ *
+ * @reset_type: Reset type
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ */
+struct mpi3mr_bsg_adp_reset {
+	__u8	reset_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+};
+
+/**
+ * struct mpi3mr_change_count - Topology change count
+ * returned by the driver.
+ *
+ * @change_count: Topology change count
+ * @rsvd: Reserved
+ */
+struct mpi3mr_change_count {
+	__u16	change_count;
+	__u16	rsvd;
+};
+
+/**
+ * struct mpi3mr_device_map_info - Target device mapping
+ * information
+ *
+ * @handle: Firmware device handle
+ * @perst_id: Persistent ID assigned by the firmware
+ * @target_id: Target ID assigned by the driver
+ * @bus_id: Bus ID assigned by the driver
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ */
+struct mpi3mr_device_map_info {
+	__u16	handle;
+	__u16	perst_id;
+	__u32	target_id;
+	__u8	bus_id;
+	__u8	rsvd1;
+	__u16	rsvd2;
+};
+
+/**
+ * struct mpi3mr_all_tgt_info - Target device mapping
+ * information returned by the driver
+ *
+ * @num_devices: The number of devices in driver's inventory
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @dmi: Variable length array of mapping information of targets
+ */
+struct mpi3mr_all_tgt_info {
+	__u16	num_devices;
+	__u16	rsvd1;
+	__u32	rsvd2;
+	struct mpi3mr_device_map_info dmi[1];
+};
+
+/**
+ * struct mpi3mr_logdata_enable - Number of log data
+ * entries saved by the driver returned as payload data for
+ * enable logdata BSG request by the driver.
+ *
+ * @max_entries: Number of log data entries cached by the driver
+ * @rsvd: Reserved
+ */
+struct mpi3mr_logdata_enable {
+	__u16	max_entries;
+	__u16	rsvd;
+};
+
+/**
+ * struct mpi3mr_bsg_out_pel_enable - PEL enable request payload
+ * data to the driver.
+ *
+ * @pel_locale: PEL locale to the firmware
+ * @pel_class: PEL class to the firmware
+ * @rsvd: Reserved
+ */
+struct mpi3mr_bsg_out_pel_enable {
+	__u16	pel_locale;
+	__u8	pel_class;
+	__u8	rsvd;
+};
+
+/**
+ * struct mpi3mr_logdata_entry - Log data entry cached by the
+ * driver.
+ *
+ * @valid_entry: Is the entry valid
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @data: Variable length Log entry data
+ */
+struct mpi3mr_logdata_entry {
+	__u8	valid_entry;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u8	data[1]; /* Variable length Array */
+};
+
+/**
+ * struct mpi3mr_bsg_in_log_data - Log data entries saved by
+ * the driver returned as payload data for Get logdata request
+ * by the driver.
+ *
+ * @entry: Variable length Log data entry array
+ */
+struct mpi3mr_bsg_in_log_data {
+	struct mpi3mr_logdata_entry entry[1];
+};
+
+/**
+ * struct mpi3mr_hdb_entry - host diag buffer entry.
+ *
+ * @buf_type: Buffer type
+ * @status: Buffer status
+ * @trigger_type: Trigger type
+ * @rsvd1: Reserved
+ * @size: Buffer size
+ * @rsvd2: Reserved
+ * @trigger_data: Trigger specific data
+ * @rsvd3: Reserved
+ * @rsvd4: Reserved
+ */
+struct mpi3mr_hdb_entry {
+	__u8	buf_type;
+	__u8	status;
+	__u8	trigger_type;
+	__u8	rsvd1;
+	__u16	size;
+	__u16	rsvd2;
+	__u64	trigger_data;
+	__u32	rsvd3;
+	__u32	rsvd4;
+};
+
+
+/**
+ * struct mpi3mr_bsg_in_hdb_status - This structure contains
+ * return data for the BSG request to retrieve the number of host
+ * diagnostic buffers supported by the driver and their current
+ * status and additional status specific data if any in forms of
+ * multiple hdb entries.
+ *
+ * @num_hdb_types: Number of host diag buffer types supported
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @rsvd3: Reserved
+ * @entry: Variable length Diag buffer status entry array
+ */
+struct mpi3mr_bsg_in_hdb_status {
+	__u8	num_hdb_types;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u32	rsvd3;
+	struct mpi3mr_hdb_entry entry[1];
+};
+
+/**
+ * struct mpi3mr_bsg_out_repost_hdb - Repost host diagnostic
+ * buffer request payload data to the driver.
+ *
+ * @buf_type: Buffer type
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ */
+struct mpi3mr_bsg_out_repost_hdb {
+	__u8	buf_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+};
+
+/**
+ * struct mpi3mr_bsg_out_upload_hdb - Upload host diagnostic
+ * buffer request payload data to the driver.
+ *
+ * @buf_type: Buffer type
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @start_offset: Start offset of the buffer from where to copy
+ * @length: Length of the buffer to copy
+ */
+struct mpi3mr_bsg_out_upload_hdb {
+	__u8	buf_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u32	start_offset;
+	__u32	length;
+};
+
+/**
+ * struct mpi3mr_bsg_out_refresh_hdb_triggers - Refresh host
+ * diagnostic buffer triggers request payload data to the driver.
+ *
+ * @page_type: Page type
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ */
+struct mpi3mr_bsg_out_refresh_hdb_triggers {
+	__u8	page_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+};
+/**
+ * struct mpi3mr_bsg_drv_cmd -  Generic bsg data
+ * structure for all driver specific requests.
+ *
+ * @mrioc_id: Controller ID
+ * @opcode: Driver specific opcode
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ */
+struct mpi3mr_bsg_drv_cmd {
+	__u8	mrioc_id;
+	__u8	opcode;
+	__u16	rsvd1;
+	__u32	rsvd2[4];
+};
+/**
+ * struct mpi3mr_bsg_in_reply_buf - MPI reply buffer returned
+ * for MPI Passthrough request .
+ *
+ * @mpi_reply_type: Type of MPI reply
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @reply_buf: Variable Length buffer based on mpirep type
+ */
+struct mpi3mr_bsg_in_reply_buf {
+	__u8	mpi_reply_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u8	reply_buf[1];
+};
+
+/**
+ * struct mpi3mr_buf_entry - User buffer descriptor for MPI
+ * Passthrough requests.
+ *
+ * @buf_type: Buffer type
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @buf_len: Buffer length
+ */
+struct mpi3mr_buf_entry {
+	__u8	buf_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u32	buf_len;
+};
+/**
+ * struct mpi3mr_bsg_buf_entry_list - list of user buffer
+ * descriptor for MPI Passthrough requests.
+ *
+ * @num_of_entries: Number of buffer descriptors
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @rsvd3: Reserved
+ * @buf_entry: Variable length array of buffer descriptors
+ */
+struct mpi3mr_buf_entry_list {
+	__u8	num_of_entries;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u32	rsvd3;
+	struct mpi3mr_buf_entry buf_entry[1];
+};
+/**
+ * struct mpi3mr_bsg_mptcmd -  Generic bsg data
+ * structure for all MPI Passthrough requests .
+ *
+ * @mrioc_id: Controller ID
+ * @rsvd1: Reserved
+ * @timeout: MPI request timeout
+ * @buf_entry_list: Buffer descriptor list
+ */
+struct mpi3mr_bsg_mptcmd {
+	__u8	mrioc_id;
+	__u8	rsvd1;
+	__u16	timeout;
+	__u32	rsvd2;
+	struct mpi3mr_buf_entry_list buf_entry_list;
+};
+
+/**
+ * struct mpi3mr_bsg_packet -  Generic bsg data
+ * structure for all supported requests .
+ *
+ * @cmd_type: represents drvrcmd or mptcmd
+ * @rsvd1: Reserved
+ * @rsvd2: Reserved
+ * @drvrcmd: driver request structure
+ * @mptcmd: mpt request structure
+ */
+struct mpi3mr_bsg_packet {
+	__u8	cmd_type;
+	__u8	rsvd1;
+	__u16	rsvd2;
+	__u32	rsvd3;
+	union {
+		struct mpi3mr_bsg_drv_cmd drvrcmd;
+		struct mpi3mr_bsg_mptcmd mptcmd;
+	} cmd;
+};
+
+
+/* MPI3: NVMe Encasulation related definitions */
+#ifndef MPI3_NVME_ENCAP_CMD_MAX
+#define MPI3_NVME_ENCAP_CMD_MAX               (1)
+#endif
+
+struct mpi3_nvme_encapsulated_request {
+	__le16	host_tag;
+	__u8	ioc_use_only02;
+	__u8	function;
+	__le16	ioc_use_only04;
+	__u8	ioc_use_only06;
+	__u8	msg_flags;
+	__le16	change_count;
+	__le16	dev_handle;
+	__le16	encapsulated_command_length;
+	__le16	flags;
+	__le32	data_length;
+	__le32  reserved14[3];
+	__le32	command[MPI3_NVME_ENCAP_CMD_MAX];
+};
+
+struct mpi3_nvme_encapsulated_error_reply {
+	__le16	host_tag;
+	__u8	ioc_use_only02;
+	__u8	function;
+	__le16	ioc_use_only04;
+	__u8	ioc_use_only06;
+	__u8	msg_flags;
+	__le16	ioc_use_only08;
+	__le16	ioc_status;
+	__le32	ioc_log_info;
+	__le32	nvme_completion_entry[4];
+};
+
+#define	MPI3MR_NVME_PRP_SIZE		8 /* PRP size */
+#define	MPI3MR_NVME_CMD_PRP1_OFFSET	24 /* PRP1 offset in NVMe cmd */
+#define	MPI3MR_NVME_CMD_PRP2_OFFSET	32 /* PRP2 offset in NVMe cmd */
+#define	MPI3MR_NVME_CMD_SGL_OFFSET	24 /* SGL offset in NVMe cmd */
+#define MPI3MR_NVME_DATA_FORMAT_PRP	0
+#define MPI3MR_NVME_DATA_FORMAT_SGL1	1
+#define MPI3MR_NVME_DATA_FORMAT_SGL2	2
+
+/* MPI3: task management related definitions */
+struct mpi3_scsi_task_mgmt_request {
+	__le16	host_tag;
+	__u8	ioc_use_only02;
+	__u8	function;
+	__le16	ioc_use_only04;
+	__u8	ioc_use_only06;
+	__u8    msg_flags;
+	__le16	change_count;
+	__le16	dev_handle;
+	__le16	task_host_tag;
+	__u8	task_type;
+	__u8	reserved0f;
+	__le16	task_request_queue_id;
+	__le16	reserved12;
+	__le32	reserved14;
+	__u8	lun[8];
+};
+
+#define MPI3_SCSITASKMGMT_MSGFLAGS_DO_NOT_SEND_TASK_IU      (0x08)
+#define MPI3_SCSITASKMGMT_TASKTYPE_ABORT_TASK               (0x01)
+#define MPI3_SCSITASKMGMT_TASKTYPE_ABORT_TASK_SET           (0x02)
+#define MPI3_SCSITASKMGMT_TASKTYPE_TARGET_RESET             (0x03)
+#define MPI3_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET       (0x05)
+#define MPI3_SCSITASKMGMT_TASKTYPE_CLEAR_TASK_SET           (0x06)
+#define MPI3_SCSITASKMGMT_TASKTYPE_QUERY_TASK               (0x07)
+#define MPI3_SCSITASKMGMT_TASKTYPE_CLEAR_ACA                (0x08)
+#define MPI3_SCSITASKMGMT_TASKTYPE_QUERY_TASK_SET           (0x09)
+#define MPI3_SCSITASKMGMT_TASKTYPE_QUERY_ASYNC_EVENT        (0x0a)
+#define MPI3_SCSITASKMGMT_TASKTYPE_I_T_NEXUS_RESET          (0x0b)
+struct mpi3_scsi_task_mgmt_reply {
+	__le16	host_tag;
+	__u8	ioc_use_only02;
+	__u8	function;
+	__le16  ioc_use_only04;
+	__u8	ioc_use_only06;
+	__u8	msg_flags;
+	__le16	ioc_use_only08;
+	__le16	ioc_status;
+	__le32	ioc_log_info;
+	__le32	termination_count;
+	__le32	response_data;
+	__le32	reserved18;
+};
+
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_COMPLETE                (0x00)
+#define MPI3_SCSITASKMGMT_RSPCODE_INVALID_FRAME              (0x02)
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_FUNCTION_NOT_SUPPORTED  (0x04)
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_FAILED                  (0x05)
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_SUCCEEDED               (0x08)
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_INVALID_LUN             (0x09)
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_OVERLAPPED_TAG          (0x0a)
+#define MPI3_SCSITASKMGMT_RSPCODE_IO_QUEUED_ON_IOC           (0x80)
+#define MPI3_SCSITASKMGMT_RSPCODE_TM_NVME_DENIED             (0x81)
+
+/* MPI3: PEL related definitions */
+#define MPI3_PEL_LOCALE_FLAGS_NON_BLOCKING_BOOT_EVENT   (0x0200)
+#define MPI3_PEL_LOCALE_FLAGS_BLOCKING_BOOT_EVENT       (0x0100)
+#define MPI3_PEL_LOCALE_FLAGS_PCIE                      (0x0080)
+#define MPI3_PEL_LOCALE_FLAGS_CONFIGURATION             (0x0040)
+#define MPI3_PEL_LOCALE_FLAGS_CONTROLER                 (0x0020)
+#define MPI3_PEL_LOCALE_FLAGS_SAS                       (0x0010)
+#define MPI3_PEL_LOCALE_FLAGS_EPACK                     (0x0008)
+#define MPI3_PEL_LOCALE_FLAGS_ENCLOSURE                 (0x0004)
+#define MPI3_PEL_LOCALE_FLAGS_PD                        (0x0002)
+#define MPI3_PEL_LOCALE_FLAGS_VD                        (0x0001)
+#define MPI3_PEL_CLASS_DEBUG                            (0x00)
+#define MPI3_PEL_CLASS_PROGRESS                         (0x01)
+#define MPI3_PEL_CLASS_INFORMATIONAL                    (0x02)
+#define MPI3_PEL_CLASS_WARNING                          (0x03)
+#define MPI3_PEL_CLASS_CRITICAL                         (0x04)
+#define MPI3_PEL_CLASS_FATAL                            (0x05)
+#define MPI3_PEL_CLASS_FAULT                            (0x06)
+
+/* MPI3: Function definitions */
+#define MPI3_BSG_FUNCTION_MGMT_PASSTHROUGH              (0x0a)
+#define MPI3_BSG_FUNCTION_SCSI_IO                       (0x20)
+#define MPI3_BSG_FUNCTION_SCSI_TASK_MGMT                (0x21)
+#define MPI3_BSG_FUNCTION_SMP_PASSTHROUGH               (0x22)
+#define MPI3_BSG_FUNCTION_NVME_ENCAPSULATED             (0x24)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/sound/asequencer.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/sound/asequencer.h
@@ -344,10 +344,10 @@
 #define	KERNEL_CLIENT	((__force snd_seq_client_type_t) 2)
                         
 	/* event filter flags */
-#define SNDRV_SEQ_FILTER_BROADCAST	(1<<0)	/* accept broadcast messages */
-#define SNDRV_SEQ_FILTER_MULTICAST	(1<<1)	/* accept multicast messages */
-#define SNDRV_SEQ_FILTER_BOUNCE		(1<<2)	/* accept bounce event in error */
-#define SNDRV_SEQ_FILTER_USE_EVENT	(1<<31)	/* use event filter */
+#define SNDRV_SEQ_FILTER_BROADCAST	(1U<<0)	/* accept broadcast messages */
+#define SNDRV_SEQ_FILTER_MULTICAST	(1U<<1)	/* accept multicast messages */
+#define SNDRV_SEQ_FILTER_BOUNCE		(1U<<2)	/* accept bounce event in error */
+#define SNDRV_SEQ_FILTER_USE_EVENT	(1U<<31)	/* use event filter */
 
 struct snd_seq_client_info {
 	int client;			/* client number to inquire */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/sound/asound.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/sound/asound.h
@@ -56,8 +56,10 @@
  *                                                                          *
  ****************************************************************************/
 
+#define AES_IEC958_STATUS_SIZE		24
+
 struct snd_aes_iec958 {
-	unsigned char status[24];	/* AES/IEC958 channel status bits */
+	unsigned char status[AES_IEC958_STATUS_SIZE]; /* AES/IEC958 channel status bits */
 	unsigned char subcode[147];	/* AES/IEC958 subcode bits */
 	unsigned char pad;		/* nothing */
 	unsigned char dig_subframe[4];	/* AES/IEC958 subframe bits */
--- linux-xilinx-zynqmp-5.15.0.orig/include/uapi/sound/skl-tplg-interface.h
+++ linux-xilinx-zynqmp-5.15.0/include/uapi/sound/skl-tplg-interface.h
@@ -66,7 +66,8 @@
 	SKL_CH_CFG_DUAL_MONO = 9,
 	SKL_CH_CFG_I2S_DUAL_STEREO_0 = 10,
 	SKL_CH_CFG_I2S_DUAL_STEREO_1 = 11,
-	SKL_CH_CFG_4_CHANNEL = 12,
+	SKL_CH_CFG_7_1 = 12,
+	SKL_CH_CFG_4_CHANNEL = SKL_CH_CFG_7_1,
 	SKL_CH_CFG_INVALID
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/include/video/of_display_timing.h
+++ linux-xilinx-zynqmp-5.15.0/include/video/of_display_timing.h
@@ -8,6 +8,8 @@
 #ifndef __LINUX_OF_DISPLAY_TIMING_H
 #define __LINUX_OF_DISPLAY_TIMING_H
 
+#include <linux/errno.h>
+
 struct device_node;
 struct display_timing;
 struct display_timings;
--- linux-xilinx-zynqmp-5.15.0.orig/include/xen/events.h
+++ linux-xilinx-zynqmp-5.15.0/include/xen/events.h
@@ -17,6 +17,7 @@
 unsigned xen_evtchn_nr_channels(void);
 
 int bind_evtchn_to_irq(evtchn_port_t evtchn);
+int bind_evtchn_to_irq_lateeoi(evtchn_port_t evtchn);
 int bind_evtchn_to_irqhandler(evtchn_port_t evtchn,
 			      irq_handler_t handler,
 			      unsigned long irqflags, const char *devname,
--- linux-xilinx-zynqmp-5.15.0.orig/include/xen/grant_table.h
+++ linux-xilinx-zynqmp-5.15.0/include/xen/grant_table.h
@@ -104,17 +104,32 @@
  * access has been ended, free the given page too.  Access will be ended
  * immediately iff the grant entry is not in use, otherwise it will happen
  * some time later.  page may be 0, in which case no freeing will occur.
+ * Note that the granted page might still be accessed (read or write) by the
+ * other side after gnttab_end_foreign_access() returns, so even if page was
+ * specified as 0 it is not allowed to just reuse the page for other
+ * purposes immediately. gnttab_end_foreign_access() will take an additional
+ * reference to the granted page in this case, which is dropped only after
+ * the grant is no longer in use.
+ * This requires that multi page allocations for areas subject to
+ * gnttab_end_foreign_access() are done via alloc_pages_exact() (and freeing
+ * via free_pages_exact()) in order to avoid high order pages.
  */
 void gnttab_end_foreign_access(grant_ref_t ref, int readonly,
 			       unsigned long page);
 
+/*
+ * End access through the given grant reference, iff the grant entry is
+ * no longer in use.  In case of success ending foreign access, the
+ * grant reference is deallocated.
+ * Return 1 if the grant entry was freed, 0 if it is still in use.
+ */
+int gnttab_try_end_foreign_access(grant_ref_t ref);
+
 int gnttab_grant_foreign_transfer(domid_t domid, unsigned long pfn);
 
 unsigned long gnttab_end_foreign_transfer_ref(grant_ref_t ref);
 unsigned long gnttab_end_foreign_transfer(grant_ref_t ref);
 
-int gnttab_query_foreign_access(grant_ref_t ref);
-
 /*
  * operations on reserved batches of grant references
  */
--- linux-xilinx-zynqmp-5.15.0.orig/include/xen/interface/platform.h
+++ linux-xilinx-zynqmp-5.15.0/include/xen/interface/platform.h
@@ -500,6 +500,8 @@
 };
 DEFINE_GUEST_HANDLE_STRUCT(xenpf_symdata);
 
+#define XENPF_get_dom0_console 64
+
 struct xen_platform_op {
 	uint32_t cmd;
 	uint32_t interface_version; /* XENPF_INTERFACE_VERSION */
@@ -523,6 +525,7 @@
 		struct xenpf_mem_hotadd        mem_add;
 		struct xenpf_core_parking      core_parking;
 		struct xenpf_symdata           symdata;
+		struct dom0_vga_console_info   dom0_console;
 		uint8_t                        pad[128];
 	} u;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/include/xen/pvcalls.h
+++ linux-xilinx-zynqmp-5.15.0/include/xen/pvcalls.h
@@ -0,0 +1,13 @@
+#ifndef __LINUX_NET_PVCALLS_H
+#define __LINUX_NET_PVCALLS_H
+
+#include <linux/net.h>
+
+#ifdef CONFIG_XEN_PVCALLS_FRONTEND
+extern bool pvcalls;
+#else
+#define pvcalls (0)
+#endif
+extern const struct proto_ops pvcalls_stream_ops;
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/include/xen/xen.h
+++ linux-xilinx-zynqmp-5.15.0/include/xen/xen.h
@@ -61,4 +61,15 @@
 #include <xen/balloon.h>
 #endif
 
+#if defined(CONFIG_XEN_DOM0) && defined(CONFIG_ACPI) && defined(CONFIG_X86)
+bool __init xen_processor_present(uint32_t acpi_id);
+#else
+#include <linux/bug.h>
+static inline bool xen_processor_present(uint32_t acpi_id)
+{
+	BUG();
+	return false;
+}
+#endif
+
 #endif	/* _XEN_XEN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/init/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/init/Kconfig
@@ -77,6 +77,11 @@
 	depends on CC_HAS_ASM_GOTO
 	def_bool $(success,echo 'int foo(int x) { asm goto ("": "=r"(x) ::: bar); return x; bar: return 0; }' | $(CC) -x c - -c -o /dev/null)
 
+config CC_HAS_ASM_GOTO_TIED_OUTPUT
+	depends on CC_HAS_ASM_GOTO_OUTPUT
+	# Detect buggy gcc and clang, fixed in gcc-11 clang-14.
+	def_bool $(success,echo 'int foo(int *x) { asm goto (".long (%l[bar]) - .": "+m"(*x) ::: bar); return *x; bar: return 0; }' | $CC -x c - -c -o /dev/null)
+
 config TOOLS_SUPPORT_RELR
 	def_bool $(success,env "CC=$(CC)" "LD=$(LD)" "NM=$(NM)" "OBJCOPY=$(OBJCOPY)" $(srctree)/scripts/tools-support-relr.sh)
 
@@ -86,6 +91,10 @@
 config CC_HAS_NO_PROFILE_FN_ATTR
 	def_bool $(success,echo '__attribute__((no_profile_instrument_function)) int x();' | $(CC) -x c - -c -o /dev/null -Werror)
 
+config PAHOLE_VERSION
+	int
+	default $(shell,$(srctree)/scripts/pahole-version.sh $(PAHOLE))
+
 config CONSTRUCTORS
 	bool
 
@@ -355,6 +364,15 @@
 config ARCH_NO_SWAP
 	bool
 
+config VERSION_SIGNATURE
+	string "Arbitrary version signature"
+	help
+	  This string will be created in a file, /proc/version_signature. It
+	  is useful in determining arbitrary data about your kernel. For instance,
+	  if you have several kernels of the same version, but need to keep track
+	  of a revision of the same kernel, but not affect it's ability to load
+	  compatible modules, this is the easiest way to do that.
+
 config SWAP
 	bool "Support for paging of anonymous memory (swap)"
 	depends on MMU && BLOCK && !ARCH_NO_SWAP
--- linux-xilinx-zynqmp-5.15.0.orig/init/do_mounts.c
+++ linux-xilinx-zynqmp-5.15.0/init/do_mounts.c
@@ -600,6 +600,8 @@
  */
 void __init prepare_namespace(void)
 {
+	int err;
+
 	if (root_delay) {
 		printk(KERN_INFO "Waiting %d sec before mounting root device...\n",
 		       root_delay);
@@ -647,6 +649,13 @@
 	devtmpfs_mount();
 	init_mount(".", "/", NULL, MS_MOVE, NULL);
 	init_chroot(".");
+#ifdef CONFIG_BLOCK
+	/* recreate the /dev/root */
+	err = create_dev("/dev/root", ROOT_DEV);
+
+	if (err < 0)
+		pr_emerg("Failed to create /dev/root: %d\n", err);
+#endif
 }
 
 static bool is_tmpfs;
@@ -666,7 +675,10 @@
 
 void __init init_rootfs(void)
 {
-	if (IS_ENABLED(CONFIG_TMPFS) && !saved_root_name[0] &&
-		(!root_fs_names || strstr(root_fs_names, "tmpfs")))
-		is_tmpfs = true;
+	if (IS_ENABLED(CONFIG_TMPFS)) {
+		if (!saved_root_name[0] && !root_fs_names)
+			is_tmpfs = true;
+		else if (root_fs_names && !!strstr(root_fs_names, "tmpfs"))
+			is_tmpfs = true;
+	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/init/initramfs.c
+++ linux-xilinx-zynqmp-5.15.0/init/initramfs.c
@@ -338,6 +338,15 @@
 {
 	state = SkipIt;
 	next_state = Reset;
+
+	/* name_len > 0 && name_len <= PATH_MAX checked in do_header */
+	if (collected[name_len - 1] != '\0') {
+		pr_err("initramfs name without nulterm: %.*s\n",
+		       (int)name_len, collected);
+		error("malformed archive");
+		return 1;
+	}
+
 	if (strcmp(collected, "TRAILER!!!") == 0) {
 		free_hash();
 		return 0;
@@ -403,6 +412,12 @@
 
 static int __init do_symlink(void)
 {
+	if (collected[name_len - 1] != '\0') {
+		pr_err("initramfs symlink without nulterm: %.*s\n",
+		       (int)name_len, collected);
+		error("malformed archive");
+		return 1;
+	}
 	collected[N_ALIGN(name_len) + body_len] = '\0';
 	clean_path(collected, 0);
 	init_symlink(collected + N_ALIGN(name_len), collected);
@@ -655,7 +670,7 @@
 
 	printk(KERN_INFO "rootfs image is not initramfs (%s); looks like an initrd\n",
 			err);
-	file = filp_open("/initrd.image", O_WRONLY | O_CREAT, 0700);
+	file = filp_open("/initrd.image", O_WRONLY|O_CREAT|O_LARGEFILE, 0700);
 	if (IS_ERR(file))
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/init/main.c
+++ linux-xilinx-zynqmp-5.15.0/init/main.c
@@ -89,6 +89,7 @@
 #include <linux/sched/task_stack.h>
 #include <linux/context_tracking.h>
 #include <linux/random.h>
+#include <linux/moduleloader.h>
 #include <linux/list.h>
 #include <linux/integrity.h>
 #include <linux/proc_ns.h>
@@ -96,13 +97,13 @@
 #include <linux/cache.h>
 #include <linux/rodata_test.h>
 #include <linux/jump_label.h>
-#include <linux/mem_encrypt.h>
 #include <linux/kcsan.h>
 #include <linux/init_syscalls.h>
 #include <linux/stackdepot.h>
+#include <linux/randomize_kstack.h>
+#include <net/net_namespace.h>
 
 #include <asm/io.h>
-#include <asm/bugs.h>
 #include <asm/setup.h>
 #include <asm/sections.h>
 #include <asm/cacheflush.h>
@@ -540,6 +541,10 @@
 {
 	size_t len = strlen(param);
 
+	/* Handle params aliased to sysctls */
+	if (sysctl_is_alias(param))
+		return 0;
+
 	repair_env_string(param, val);
 
 	/* Handle obsolete-style parameters */
@@ -635,6 +640,8 @@
 	if (!saved_command_line)
 		panic("%s: Failed to allocate %zu bytes\n", __func__, len + ilen);
 
+	len = xlen + strlen(command_line) + 1;
+
 	static_command_line = memblock_alloc(len, SMP_CACHE_BYTES);
 	if (!static_command_line)
 		panic("%s: Failed to allocate %zu bytes\n", __func__, len);
@@ -786,8 +793,6 @@
 }
 #endif
 
-void __init __weak mem_encrypt_init(void) { }
-
 void __init __weak poking_init(void) { }
 
 void __init __weak pgtable_cache_init(void) { }
@@ -857,6 +862,7 @@
 	init_espfix_bsp();
 	/* Should be run after espfix64 is set up. */
 	pti_init();
+	mm_cache_init();
 }
 
 #ifdef CONFIG_HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET
@@ -924,7 +930,9 @@
 	for (p = &envp_init[2]; *p; p++)
 		end += sprintf(end, " %s", *p);
 
-	pr_notice("Unknown command line parameters:%s\n", unknown_options);
+	/* Start at unknown_options[1] to skip the initial space */
+	pr_notice("Unknown kernel command line parameters \"%s\", will be passed to user space.\n",
+		&unknown_options[1]);
 	memblock_free_ptr(unknown_options, len);
 }
 
@@ -987,7 +995,7 @@
 	sort_main_extable();
 	trap_init();
 	mm_init();
-
+	poking_init();
 	ftrace_init();
 
 	/* trace_printk can be enabled here */
@@ -1038,21 +1046,18 @@
 	softirq_init();
 	timekeeping_init();
 	kfence_init();
+	time_init();
 
 	/*
 	 * For best initial stack canary entropy, prepare it after:
 	 * - setup_arch() for any UEFI RNG entropy and boot cmdline access
-	 * - timekeeping_init() for ktime entropy used in rand_initialize()
-	 * - rand_initialize() to get any arch-specific entropy like RDRAND
-	 * - add_latent_entropy() to get any latent entropy
-	 * - adding command line entropy
+	 * - timekeeping_init() for ktime entropy used in random_init()
+	 * - time_init() for making random_get_entropy() work on some platforms
+	 * - random_init() to initialize the RNG from from early entropy sources
 	 */
-	rand_initialize();
-	add_latent_entropy();
-	add_device_randomness(command_line, strlen(command_line));
+	random_init(command_line);
 	boot_init_stack_canary();
 
-	time_init();
 	perf_event_init();
 	profile_init();
 	call_function_init();
@@ -1082,14 +1087,6 @@
 	 */
 	locking_selftest();
 
-	/*
-	 * This needs to be called before any devices perform DMA
-	 * operations that might use the SWIOTLB bounce buffers. It will
-	 * mark the bounce buffers as decrypted so that their usage will
-	 * not cause "plain-text" data to be decrypted when accessed.
-	 */
-	mem_encrypt_init();
-
 #ifdef CONFIG_BLK_DEV_INITRD
 	if (initrd_start && !initrd_below_start_ok &&
 	    page_to_pfn(virt_to_page((void *)initrd_start)) < min_low_pfn) {
@@ -1106,6 +1103,9 @@
 		late_time_init();
 	sched_clock_init();
 	calibrate_delay();
+
+	arch_cpu_finalize_init();
+
 	pid_idr_init();
 	anon_vma_init();
 #ifdef CONFIG_X86
@@ -1120,6 +1120,7 @@
 	key_init();
 	security_init();
 	dbg_late_init();
+	net_ns_init();
 	vfs_caches_init();
 	pagecache_init();
 	signals_init();
@@ -1131,9 +1132,6 @@
 	taskstats_init_early();
 	delayacct_init();
 
-	poking_init();
-	check_bugs();
-
 	acpi_subsystem_init();
 	arch_post_acpi_subsys_init();
 	kcsan_init();
@@ -1194,7 +1192,7 @@
 		}
 	} while (str_entry);
 
-	return 0;
+	return 1;
 }
 
 static bool __init_or_module initcall_blacklisted(initcall_t fn)
@@ -1241,22 +1239,22 @@
 static __init_or_module void
 trace_initcall_start_cb(void *data, initcall_t fn)
 {
-	ktime_t *calltime = (ktime_t *)data;
+	unsigned long *calltime = (unsigned long *)data;
 
 	printk(KERN_DEBUG "calling  %pS @ %i\n", fn, task_pid_nr(current));
-	*calltime = ktime_get();
+	*calltime = local_clock();
 }
 
 static __init_or_module void
 trace_initcall_finish_cb(void *data, initcall_t fn, int ret)
 {
-	ktime_t *calltime = (ktime_t *)data;
-	ktime_t delta, rettime;
+	unsigned long *calltime = (unsigned long *)data;
+	unsigned long delta, rettime;
 	unsigned long long duration;
 
-	rettime = ktime_get();
-	delta = ktime_sub(rettime, *calltime);
-	duration = (unsigned long long) ktime_to_ns(delta) >> 10;
+	rettime = local_clock();
+	delta = rettime - *calltime;
+	duration = delta >> 10;
 	printk(KERN_DEBUG "initcall %pS returned %d after %lld usecs\n",
 		 fn, ret, duration);
 }
@@ -1456,7 +1454,9 @@
 bool rodata_enabled __ro_after_init = true;
 static int __init set_debug_rodata(char *str)
 {
-	return strtobool(str, &rodata_enabled);
+	if (strtobool(str, &rodata_enabled))
+		pr_warn("Invalid option string for rodata: '%s'\n", str);
+	return 1;
 }
 __setup("rodata=", set_debug_rodata);
 #endif
@@ -1467,11 +1467,11 @@
 	if (rodata_enabled) {
 		/*
 		 * load_module() results in W+X mappings, which are cleaned
-		 * up with call_rcu().  Let's make sure that queued work is
+		 * up with init_free_wq. Let's make sure that queued work is
 		 * flushed so that we don't hit false positives looking for
 		 * insecure pages which are W+X.
 		 */
-		rcu_barrier();
+		flush_module_init_free_work();
 		mark_rodata_ro();
 		rodata_test();
 	} else
--- linux-xilinx-zynqmp-5.15.0.orig/init/version.c
+++ linux-xilinx-zynqmp-5.15.0/init/version.c
@@ -38,7 +38,11 @@
 /* FIXED STRINGS! Don't touch! */
 const char linux_banner[] =
 	"Linux version " UTS_RELEASE " (" LINUX_COMPILE_BY "@"
-	LINUX_COMPILE_HOST ") (" LINUX_COMPILER ") " UTS_VERSION "\n";
+	LINUX_COMPILE_HOST ") (" LINUX_COMPILER ") " UTS_VERSION
+#ifdef CONFIG_VERSION_SIGNATURE
+        " (" CONFIG_VERSION_SIGNATURE ")"
+#endif
+	"\n";
 
 const char linux_proc_banner[] =
 	"%s version %s"
--- linux-xilinx-zynqmp-5.15.0.orig/io_uring/Makefile
+++ linux-xilinx-zynqmp-5.15.0/io_uring/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for io_uring
+
+obj-$(CONFIG_IO_URING)		+= io_uring.o
+obj-$(CONFIG_IO_WQ)		+= io-wq.o
--- linux-xilinx-zynqmp-5.15.0.orig/io_uring/io-wq.c
+++ linux-xilinx-zynqmp-5.15.0/io_uring/io-wq.c
@@ -0,0 +1,1418 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Basic worker thread pool for io_uring
+ *
+ * Copyright (C) 2019 Jens Axboe
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/sched/signal.h>
+#include <linux/percpu.h>
+#include <linux/slab.h>
+#include <linux/rculist_nulls.h>
+#include <linux/cpu.h>
+#include <linux/tracehook.h>
+#include <uapi/linux/io_uring.h>
+
+#include "io-wq.h"
+
+#define WORKER_IDLE_TIMEOUT	(5 * HZ)
+#define WORKER_INIT_LIMIT	3
+
+enum {
+	IO_WORKER_F_UP		= 1,	/* up and active */
+	IO_WORKER_F_RUNNING	= 2,	/* account as running */
+	IO_WORKER_F_FREE	= 4,	/* worker on free list */
+	IO_WORKER_F_BOUND	= 8,	/* is doing bounded work */
+};
+
+enum {
+	IO_WQ_BIT_EXIT		= 0,	/* wq exiting */
+};
+
+enum {
+	IO_ACCT_STALLED_BIT	= 0,	/* stalled on hash */
+};
+
+/*
+ * One for each thread in a wqe pool
+ */
+struct io_worker {
+	refcount_t ref;
+	unsigned flags;
+	struct hlist_nulls_node nulls_node;
+	struct list_head all_list;
+	struct task_struct *task;
+	struct io_wqe *wqe;
+
+	struct io_wq_work *cur_work;
+	spinlock_t lock;
+
+	struct completion ref_done;
+
+	unsigned long create_state;
+	struct callback_head create_work;
+	int create_index;
+	int init_retries;
+
+	union {
+		struct rcu_head rcu;
+		struct work_struct work;
+	};
+};
+
+#if BITS_PER_LONG == 64
+#define IO_WQ_HASH_ORDER	6
+#else
+#define IO_WQ_HASH_ORDER	5
+#endif
+
+#define IO_WQ_NR_HASH_BUCKETS	(1u << IO_WQ_HASH_ORDER)
+
+struct io_wqe_acct {
+	unsigned nr_workers;
+	unsigned max_workers;
+	int index;
+	atomic_t nr_running;
+	struct io_wq_work_list work_list;
+	unsigned long flags;
+};
+
+enum {
+	IO_WQ_ACCT_BOUND,
+	IO_WQ_ACCT_UNBOUND,
+	IO_WQ_ACCT_NR,
+};
+
+/*
+ * Per-node worker thread pool
+ */
+struct io_wqe {
+	raw_spinlock_t lock;
+	struct io_wqe_acct acct[2];
+
+	int node;
+
+	struct hlist_nulls_head free_list;
+	struct list_head all_list;
+
+	struct wait_queue_entry wait;
+
+	struct io_wq *wq;
+	struct io_wq_work *hash_tail[IO_WQ_NR_HASH_BUCKETS];
+
+	cpumask_var_t cpu_mask;
+};
+
+/*
+ * Per io_wq state
+  */
+struct io_wq {
+	unsigned long state;
+
+	free_work_fn *free_work;
+	io_wq_work_fn *do_work;
+
+	struct io_wq_hash *hash;
+
+	atomic_t worker_refs;
+	struct completion worker_done;
+
+	struct hlist_node cpuhp_node;
+
+	struct task_struct *task;
+
+	struct io_wqe *wqes[];
+};
+
+static enum cpuhp_state io_wq_online;
+
+struct io_cb_cancel_data {
+	work_cancel_fn *fn;
+	void *data;
+	int nr_running;
+	int nr_pending;
+	bool cancel_all;
+};
+
+static bool create_io_worker(struct io_wq *wq, struct io_wqe *wqe, int index);
+static void io_wqe_dec_running(struct io_worker *worker);
+static bool io_acct_cancel_pending_work(struct io_wqe *wqe,
+					struct io_wqe_acct *acct,
+					struct io_cb_cancel_data *match);
+static void create_worker_cb(struct callback_head *cb);
+static void io_wq_cancel_tw_create(struct io_wq *wq);
+
+static bool io_worker_get(struct io_worker *worker)
+{
+	return refcount_inc_not_zero(&worker->ref);
+}
+
+static void io_worker_release(struct io_worker *worker)
+{
+	if (refcount_dec_and_test(&worker->ref))
+		complete(&worker->ref_done);
+}
+
+static inline struct io_wqe_acct *io_get_acct(struct io_wqe *wqe, bool bound)
+{
+	return &wqe->acct[bound ? IO_WQ_ACCT_BOUND : IO_WQ_ACCT_UNBOUND];
+}
+
+static inline struct io_wqe_acct *io_work_get_acct(struct io_wqe *wqe,
+						   struct io_wq_work *work)
+{
+	return io_get_acct(wqe, !(work->flags & IO_WQ_WORK_UNBOUND));
+}
+
+static inline struct io_wqe_acct *io_wqe_get_acct(struct io_worker *worker)
+{
+	return io_get_acct(worker->wqe, worker->flags & IO_WORKER_F_BOUND);
+}
+
+static void io_worker_ref_put(struct io_wq *wq)
+{
+	if (atomic_dec_and_test(&wq->worker_refs))
+		complete(&wq->worker_done);
+}
+
+bool io_wq_worker_stopped(void)
+{
+	struct io_worker *worker = current->pf_io_worker;
+
+	if (WARN_ON_ONCE(!io_wq_current_is_worker()))
+		return true;
+
+	return test_bit(IO_WQ_BIT_EXIT, &worker->wqe->wq->state);
+}
+
+static void io_worker_cancel_cb(struct io_worker *worker)
+{
+	struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+	struct io_wqe *wqe = worker->wqe;
+	struct io_wq *wq = wqe->wq;
+
+	atomic_dec(&acct->nr_running);
+	raw_spin_lock(&worker->wqe->lock);
+	acct->nr_workers--;
+	raw_spin_unlock(&worker->wqe->lock);
+	io_worker_ref_put(wq);
+	clear_bit_unlock(0, &worker->create_state);
+	io_worker_release(worker);
+}
+
+static bool io_task_worker_match(struct callback_head *cb, void *data)
+{
+	struct io_worker *worker;
+
+	if (cb->func != create_worker_cb)
+		return false;
+	worker = container_of(cb, struct io_worker, create_work);
+	return worker == data;
+}
+
+static void io_worker_exit(struct io_worker *worker)
+{
+	struct io_wqe *wqe = worker->wqe;
+	struct io_wq *wq = wqe->wq;
+
+	while (1) {
+		struct callback_head *cb = task_work_cancel_match(wq->task,
+						io_task_worker_match, worker);
+
+		if (!cb)
+			break;
+		io_worker_cancel_cb(worker);
+	}
+
+	if (refcount_dec_and_test(&worker->ref))
+		complete(&worker->ref_done);
+	wait_for_completion(&worker->ref_done);
+
+	raw_spin_lock(&wqe->lock);
+	if (worker->flags & IO_WORKER_F_FREE)
+		hlist_nulls_del_rcu(&worker->nulls_node);
+	list_del_rcu(&worker->all_list);
+	preempt_disable();
+	io_wqe_dec_running(worker);
+	worker->flags = 0;
+	current->flags &= ~PF_IO_WORKER;
+	preempt_enable();
+	raw_spin_unlock(&wqe->lock);
+
+	kfree_rcu(worker, rcu);
+	io_worker_ref_put(wqe->wq);
+	do_exit(0);
+}
+
+static inline bool io_acct_run_queue(struct io_wqe_acct *acct)
+{
+	if (!wq_list_empty(&acct->work_list) &&
+	    !test_bit(IO_ACCT_STALLED_BIT, &acct->flags))
+		return true;
+	return false;
+}
+
+/*
+ * Check head of free list for an available worker. If one isn't available,
+ * caller must create one.
+ */
+static bool io_wqe_activate_free_worker(struct io_wqe *wqe,
+					struct io_wqe_acct *acct)
+	__must_hold(RCU)
+{
+	struct hlist_nulls_node *n;
+	struct io_worker *worker;
+
+	/*
+	 * Iterate free_list and see if we can find an idle worker to
+	 * activate. If a given worker is on the free_list but in the process
+	 * of exiting, keep trying.
+	 */
+	hlist_nulls_for_each_entry_rcu(worker, n, &wqe->free_list, nulls_node) {
+		if (!io_worker_get(worker))
+			continue;
+		if (io_wqe_get_acct(worker) != acct) {
+			io_worker_release(worker);
+			continue;
+		}
+		if (wake_up_process(worker->task)) {
+			io_worker_release(worker);
+			return true;
+		}
+		io_worker_release(worker);
+	}
+
+	return false;
+}
+
+/*
+ * We need a worker. If we find a free one, we're good. If not, and we're
+ * below the max number of workers, create one.
+ */
+static bool io_wqe_create_worker(struct io_wqe *wqe, struct io_wqe_acct *acct)
+{
+	/*
+	 * Most likely an attempt to queue unbounded work on an io_wq that
+	 * wasn't setup with any unbounded workers.
+	 */
+	if (unlikely(!acct->max_workers))
+		pr_warn_once("io-wq is not configured for unbound workers");
+
+	raw_spin_lock(&wqe->lock);
+	if (acct->nr_workers >= acct->max_workers) {
+		raw_spin_unlock(&wqe->lock);
+		return true;
+	}
+	acct->nr_workers++;
+	raw_spin_unlock(&wqe->lock);
+	atomic_inc(&acct->nr_running);
+	atomic_inc(&wqe->wq->worker_refs);
+	return create_io_worker(wqe->wq, wqe, acct->index);
+}
+
+static void io_wqe_inc_running(struct io_worker *worker)
+{
+	struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+
+	atomic_inc(&acct->nr_running);
+}
+
+static void create_worker_cb(struct callback_head *cb)
+{
+	struct io_worker *worker;
+	struct io_wq *wq;
+	struct io_wqe *wqe;
+	struct io_wqe_acct *acct;
+	bool do_create = false;
+
+	worker = container_of(cb, struct io_worker, create_work);
+	wqe = worker->wqe;
+	wq = wqe->wq;
+	acct = &wqe->acct[worker->create_index];
+	raw_spin_lock(&wqe->lock);
+	if (acct->nr_workers < acct->max_workers) {
+		acct->nr_workers++;
+		do_create = true;
+	}
+	raw_spin_unlock(&wqe->lock);
+	if (do_create) {
+		create_io_worker(wq, wqe, worker->create_index);
+	} else {
+		atomic_dec(&acct->nr_running);
+		io_worker_ref_put(wq);
+	}
+	clear_bit_unlock(0, &worker->create_state);
+	io_worker_release(worker);
+}
+
+static bool io_queue_worker_create(struct io_worker *worker,
+				   struct io_wqe_acct *acct,
+				   task_work_func_t func)
+{
+	struct io_wqe *wqe = worker->wqe;
+	struct io_wq *wq = wqe->wq;
+
+	/* raced with exit, just ignore create call */
+	if (test_bit(IO_WQ_BIT_EXIT, &wq->state))
+		goto fail;
+	if (!io_worker_get(worker))
+		goto fail;
+	/*
+	 * create_state manages ownership of create_work/index. We should
+	 * only need one entry per worker, as the worker going to sleep
+	 * will trigger the condition, and waking will clear it once it
+	 * runs the task_work.
+	 */
+	if (test_bit(0, &worker->create_state) ||
+	    test_and_set_bit_lock(0, &worker->create_state))
+		goto fail_release;
+
+	atomic_inc(&wq->worker_refs);
+	init_task_work(&worker->create_work, func);
+	worker->create_index = acct->index;
+	if (!task_work_add(wq->task, &worker->create_work, TWA_SIGNAL)) {
+		/*
+		 * EXIT may have been set after checking it above, check after
+		 * adding the task_work and remove any creation item if it is
+		 * now set. wq exit does that too, but we can have added this
+		 * work item after we canceled in io_wq_exit_workers().
+		 */
+		if (test_bit(IO_WQ_BIT_EXIT, &wq->state))
+			io_wq_cancel_tw_create(wq);
+		io_worker_ref_put(wq);
+		return true;
+	}
+	io_worker_ref_put(wq);
+	clear_bit_unlock(0, &worker->create_state);
+fail_release:
+	io_worker_release(worker);
+fail:
+	atomic_dec(&acct->nr_running);
+	io_worker_ref_put(wq);
+	return false;
+}
+
+static void io_wqe_dec_running(struct io_worker *worker)
+	__must_hold(wqe->lock)
+{
+	struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+	struct io_wqe *wqe = worker->wqe;
+
+	if (!(worker->flags & IO_WORKER_F_UP))
+		return;
+
+	if (atomic_dec_and_test(&acct->nr_running) && io_acct_run_queue(acct)) {
+		atomic_inc(&acct->nr_running);
+		atomic_inc(&wqe->wq->worker_refs);
+		raw_spin_unlock(&wqe->lock);
+		io_queue_worker_create(worker, acct, create_worker_cb);
+		raw_spin_lock(&wqe->lock);
+	}
+}
+
+/*
+ * Worker will start processing some work. Move it to the busy list, if
+ * it's currently on the freelist
+ */
+static void __io_worker_busy(struct io_wqe *wqe, struct io_worker *worker,
+			     struct io_wq_work *work)
+	__must_hold(wqe->lock)
+{
+	if (worker->flags & IO_WORKER_F_FREE) {
+		worker->flags &= ~IO_WORKER_F_FREE;
+		hlist_nulls_del_init_rcu(&worker->nulls_node);
+	}
+}
+
+/*
+ * No work, worker going to sleep. Move to freelist, and unuse mm if we
+ * have one attached. Dropping the mm may potentially sleep, so we drop
+ * the lock in that case and return success. Since the caller has to
+ * retry the loop in that case (we changed task state), we don't regrab
+ * the lock if we return success.
+ */
+static void __io_worker_idle(struct io_wqe *wqe, struct io_worker *worker)
+	__must_hold(wqe->lock)
+{
+	if (!(worker->flags & IO_WORKER_F_FREE)) {
+		worker->flags |= IO_WORKER_F_FREE;
+		hlist_nulls_add_head_rcu(&worker->nulls_node, &wqe->free_list);
+	}
+}
+
+static inline unsigned int io_get_work_hash(struct io_wq_work *work)
+{
+	return work->flags >> IO_WQ_HASH_SHIFT;
+}
+
+static bool io_wait_on_hash(struct io_wqe *wqe, unsigned int hash)
+{
+	struct io_wq *wq = wqe->wq;
+	bool ret = false;
+
+	spin_lock_irq(&wq->hash->wait.lock);
+	if (list_empty(&wqe->wait.entry)) {
+		__add_wait_queue(&wq->hash->wait, &wqe->wait);
+		if (!test_bit(hash, &wq->hash->map)) {
+			__set_current_state(TASK_RUNNING);
+			list_del_init(&wqe->wait.entry);
+			ret = true;
+		}
+	}
+	spin_unlock_irq(&wq->hash->wait.lock);
+	return ret;
+}
+
+static struct io_wq_work *io_get_next_work(struct io_wqe_acct *acct,
+					   struct io_worker *worker)
+	__must_hold(wqe->lock)
+{
+	struct io_wq_work_node *node, *prev;
+	struct io_wq_work *work, *tail;
+	unsigned int stall_hash = -1U;
+	struct io_wqe *wqe = worker->wqe;
+
+	wq_list_for_each(node, prev, &acct->work_list) {
+		unsigned int hash;
+
+		work = container_of(node, struct io_wq_work, list);
+
+		/* not hashed, can run anytime */
+		if (!io_wq_is_hashed(work)) {
+			wq_list_del(&acct->work_list, node, prev);
+			return work;
+		}
+
+		hash = io_get_work_hash(work);
+		/* all items with this hash lie in [work, tail] */
+		tail = wqe->hash_tail[hash];
+
+		/* hashed, can run if not already running */
+		if (!test_and_set_bit(hash, &wqe->wq->hash->map)) {
+			wqe->hash_tail[hash] = NULL;
+			wq_list_cut(&acct->work_list, &tail->list, prev);
+			return work;
+		}
+		if (stall_hash == -1U)
+			stall_hash = hash;
+		/* fast forward to a next hash, for-each will fix up @prev */
+		node = &tail->list;
+	}
+
+	if (stall_hash != -1U) {
+		bool unstalled;
+
+		/*
+		 * Set this before dropping the lock to avoid racing with new
+		 * work being added and clearing the stalled bit.
+		 */
+		set_bit(IO_ACCT_STALLED_BIT, &acct->flags);
+		raw_spin_unlock(&wqe->lock);
+		unstalled = io_wait_on_hash(wqe, stall_hash);
+		raw_spin_lock(&wqe->lock);
+		if (unstalled) {
+			clear_bit(IO_ACCT_STALLED_BIT, &acct->flags);
+			if (wq_has_sleeper(&wqe->wq->hash->wait))
+				wake_up(&wqe->wq->hash->wait);
+		}
+	}
+
+	return NULL;
+}
+
+static bool io_flush_signals(void)
+{
+	if (test_thread_flag(TIF_NOTIFY_SIGNAL) || current->task_works) {
+		__set_current_state(TASK_RUNNING);
+		tracehook_notify_signal();
+		return true;
+	}
+	return false;
+}
+
+static void io_assign_current_work(struct io_worker *worker,
+				   struct io_wq_work *work)
+{
+	if (work) {
+		io_flush_signals();
+		cond_resched();
+	}
+
+	spin_lock(&worker->lock);
+	worker->cur_work = work;
+	spin_unlock(&worker->lock);
+}
+
+static void io_wqe_enqueue(struct io_wqe *wqe, struct io_wq_work *work);
+
+static void io_worker_handle_work(struct io_worker *worker)
+	__releases(wqe->lock)
+{
+	struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+	struct io_wqe *wqe = worker->wqe;
+	struct io_wq *wq = wqe->wq;
+	bool do_kill = test_bit(IO_WQ_BIT_EXIT, &wq->state);
+
+	do {
+		struct io_wq_work *work;
+get_next:
+		/*
+		 * If we got some work, mark us as busy. If we didn't, but
+		 * the list isn't empty, it means we stalled on hashed work.
+		 * Mark us stalled so we don't keep looking for work when we
+		 * can't make progress, any work completion or insertion will
+		 * clear the stalled flag.
+		 */
+		work = io_get_next_work(acct, worker);
+		if (work)
+			__io_worker_busy(wqe, worker, work);
+
+		raw_spin_unlock(&wqe->lock);
+		if (!work)
+			break;
+		io_assign_current_work(worker, work);
+		__set_current_state(TASK_RUNNING);
+
+		/* handle a whole dependent link */
+		do {
+			struct io_wq_work *next_hashed, *linked;
+			unsigned int hash = io_get_work_hash(work);
+
+			next_hashed = wq_next_work(work);
+
+			if (unlikely(do_kill) && (work->flags & IO_WQ_WORK_UNBOUND))
+				work->flags |= IO_WQ_WORK_CANCEL;
+			wq->do_work(work);
+			io_assign_current_work(worker, NULL);
+
+			linked = wq->free_work(work);
+			work = next_hashed;
+			if (!work && linked && !io_wq_is_hashed(linked)) {
+				work = linked;
+				linked = NULL;
+			}
+			io_assign_current_work(worker, work);
+			if (linked)
+				io_wqe_enqueue(wqe, linked);
+
+			if (hash != -1U && !next_hashed) {
+				/* serialize hash clear with wake_up() */
+				spin_lock_irq(&wq->hash->wait.lock);
+				clear_bit(hash, &wq->hash->map);
+				clear_bit(IO_ACCT_STALLED_BIT, &acct->flags);
+				spin_unlock_irq(&wq->hash->wait.lock);
+				if (wq_has_sleeper(&wq->hash->wait))
+					wake_up(&wq->hash->wait);
+				raw_spin_lock(&wqe->lock);
+				/* skip unnecessary unlock-lock wqe->lock */
+				if (!work)
+					goto get_next;
+				raw_spin_unlock(&wqe->lock);
+			}
+		} while (work);
+
+		raw_spin_lock(&wqe->lock);
+	} while (1);
+}
+
+static int io_wqe_worker(void *data)
+{
+	struct io_worker *worker = data;
+	struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+	struct io_wqe *wqe = worker->wqe;
+	struct io_wq *wq = wqe->wq;
+	bool last_timeout = false;
+	char buf[TASK_COMM_LEN];
+
+	worker->flags |= (IO_WORKER_F_UP | IO_WORKER_F_RUNNING);
+
+	snprintf(buf, sizeof(buf), "iou-wrk-%d", wq->task->pid);
+	set_task_comm(current, buf);
+
+	while (!test_bit(IO_WQ_BIT_EXIT, &wq->state)) {
+		long ret;
+
+		set_current_state(TASK_INTERRUPTIBLE);
+loop:
+		raw_spin_lock(&wqe->lock);
+		if (io_acct_run_queue(acct)) {
+			io_worker_handle_work(worker);
+			goto loop;
+		}
+		/* timed out, exit unless we're the last worker */
+		if (last_timeout && acct->nr_workers > 1) {
+			acct->nr_workers--;
+			raw_spin_unlock(&wqe->lock);
+			__set_current_state(TASK_RUNNING);
+			break;
+		}
+		last_timeout = false;
+		__io_worker_idle(wqe, worker);
+		raw_spin_unlock(&wqe->lock);
+		if (io_flush_signals())
+			continue;
+		ret = schedule_timeout(WORKER_IDLE_TIMEOUT);
+		if (signal_pending(current)) {
+			struct ksignal ksig;
+
+			if (!get_signal(&ksig))
+				continue;
+			break;
+		}
+		last_timeout = !ret;
+	}
+
+	if (test_bit(IO_WQ_BIT_EXIT, &wq->state)) {
+		raw_spin_lock(&wqe->lock);
+		io_worker_handle_work(worker);
+	}
+
+	io_worker_exit(worker);
+	return 0;
+}
+
+/*
+ * Called when a worker is scheduled in. Mark us as currently running.
+ */
+void io_wq_worker_running(struct task_struct *tsk)
+{
+	struct io_worker *worker = tsk->pf_io_worker;
+
+	if (!worker)
+		return;
+	if (!(worker->flags & IO_WORKER_F_UP))
+		return;
+	if (worker->flags & IO_WORKER_F_RUNNING)
+		return;
+	worker->flags |= IO_WORKER_F_RUNNING;
+	io_wqe_inc_running(worker);
+}
+
+/*
+ * Called when worker is going to sleep. If there are no workers currently
+ * running and we have work pending, wake up a free one or create a new one.
+ */
+void io_wq_worker_sleeping(struct task_struct *tsk)
+{
+	struct io_worker *worker = tsk->pf_io_worker;
+
+	if (!worker)
+		return;
+	if (!(worker->flags & IO_WORKER_F_UP))
+		return;
+	if (!(worker->flags & IO_WORKER_F_RUNNING))
+		return;
+
+	worker->flags &= ~IO_WORKER_F_RUNNING;
+
+	raw_spin_lock(&worker->wqe->lock);
+	io_wqe_dec_running(worker);
+	raw_spin_unlock(&worker->wqe->lock);
+}
+
+static void io_init_new_worker(struct io_wqe *wqe, struct io_worker *worker,
+			       struct task_struct *tsk)
+{
+	tsk->pf_io_worker = worker;
+	worker->task = tsk;
+	set_cpus_allowed_ptr(tsk, wqe->cpu_mask);
+	tsk->flags |= PF_NO_SETAFFINITY;
+
+	raw_spin_lock(&wqe->lock);
+	hlist_nulls_add_head_rcu(&worker->nulls_node, &wqe->free_list);
+	list_add_tail_rcu(&worker->all_list, &wqe->all_list);
+	worker->flags |= IO_WORKER_F_FREE;
+	raw_spin_unlock(&wqe->lock);
+	wake_up_new_task(tsk);
+}
+
+static bool io_wq_work_match_all(struct io_wq_work *work, void *data)
+{
+	return true;
+}
+
+static inline bool io_should_retry_thread(struct io_worker *worker, long err)
+{
+	/*
+	 * Prevent perpetual task_work retry, if the task (or its group) is
+	 * exiting.
+	 */
+	if (fatal_signal_pending(current))
+		return false;
+	if (worker->init_retries++ >= WORKER_INIT_LIMIT)
+		return false;
+
+	switch (err) {
+	case -EAGAIN:
+	case -ERESTARTSYS:
+	case -ERESTARTNOINTR:
+	case -ERESTARTNOHAND:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static void create_worker_cont(struct callback_head *cb)
+{
+	struct io_worker *worker;
+	struct task_struct *tsk;
+	struct io_wqe *wqe;
+
+	worker = container_of(cb, struct io_worker, create_work);
+	clear_bit_unlock(0, &worker->create_state);
+	wqe = worker->wqe;
+	tsk = create_io_thread(io_wqe_worker, worker, wqe->node);
+	if (!IS_ERR(tsk)) {
+		io_init_new_worker(wqe, worker, tsk);
+		io_worker_release(worker);
+		return;
+	} else if (!io_should_retry_thread(worker, PTR_ERR(tsk))) {
+		struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+
+		atomic_dec(&acct->nr_running);
+		raw_spin_lock(&wqe->lock);
+		acct->nr_workers--;
+		if (!acct->nr_workers) {
+			struct io_cb_cancel_data match = {
+				.fn		= io_wq_work_match_all,
+				.cancel_all	= true,
+			};
+
+			while (io_acct_cancel_pending_work(wqe, acct, &match))
+				raw_spin_lock(&wqe->lock);
+		}
+		raw_spin_unlock(&wqe->lock);
+		io_worker_ref_put(wqe->wq);
+		kfree(worker);
+		return;
+	}
+
+	/* re-create attempts grab a new worker ref, drop the existing one */
+	io_worker_release(worker);
+	schedule_work(&worker->work);
+}
+
+static void io_workqueue_create(struct work_struct *work)
+{
+	struct io_worker *worker = container_of(work, struct io_worker, work);
+	struct io_wqe_acct *acct = io_wqe_get_acct(worker);
+
+	if (!io_queue_worker_create(worker, acct, create_worker_cont))
+		kfree(worker);
+}
+
+static bool create_io_worker(struct io_wq *wq, struct io_wqe *wqe, int index)
+{
+	struct io_wqe_acct *acct = &wqe->acct[index];
+	struct io_worker *worker;
+	struct task_struct *tsk;
+
+	__set_current_state(TASK_RUNNING);
+
+	worker = kzalloc_node(sizeof(*worker), GFP_KERNEL, wqe->node);
+	if (!worker) {
+fail:
+		atomic_dec(&acct->nr_running);
+		raw_spin_lock(&wqe->lock);
+		acct->nr_workers--;
+		raw_spin_unlock(&wqe->lock);
+		io_worker_ref_put(wq);
+		return false;
+	}
+
+	refcount_set(&worker->ref, 1);
+	worker->wqe = wqe;
+	spin_lock_init(&worker->lock);
+	init_completion(&worker->ref_done);
+
+	if (index == IO_WQ_ACCT_BOUND)
+		worker->flags |= IO_WORKER_F_BOUND;
+
+	tsk = create_io_thread(io_wqe_worker, worker, wqe->node);
+	if (!IS_ERR(tsk)) {
+		io_init_new_worker(wqe, worker, tsk);
+	} else if (!io_should_retry_thread(worker, PTR_ERR(tsk))) {
+		kfree(worker);
+		goto fail;
+	} else {
+		INIT_WORK(&worker->work, io_workqueue_create);
+		schedule_work(&worker->work);
+	}
+
+	return true;
+}
+
+/*
+ * Iterate the passed in list and call the specific function for each
+ * worker that isn't exiting
+ */
+static bool io_wq_for_each_worker(struct io_wqe *wqe,
+				  bool (*func)(struct io_worker *, void *),
+				  void *data)
+{
+	struct io_worker *worker;
+	bool ret = false;
+
+	list_for_each_entry_rcu(worker, &wqe->all_list, all_list) {
+		if (io_worker_get(worker)) {
+			/* no task if node is/was offline */
+			if (worker->task)
+				ret = func(worker, data);
+			io_worker_release(worker);
+			if (ret)
+				break;
+		}
+	}
+
+	return ret;
+}
+
+static bool io_wq_worker_wake(struct io_worker *worker, void *data)
+{
+	set_notify_signal(worker->task);
+	wake_up_process(worker->task);
+	return false;
+}
+
+static void io_run_cancel(struct io_wq_work *work, struct io_wqe *wqe)
+{
+	struct io_wq *wq = wqe->wq;
+
+	do {
+		work->flags |= IO_WQ_WORK_CANCEL;
+		wq->do_work(work);
+		work = wq->free_work(work);
+	} while (work);
+}
+
+static void io_wqe_insert_work(struct io_wqe *wqe, struct io_wq_work *work)
+{
+	struct io_wqe_acct *acct = io_work_get_acct(wqe, work);
+	unsigned int hash;
+	struct io_wq_work *tail;
+
+	if (!io_wq_is_hashed(work)) {
+append:
+		wq_list_add_tail(&work->list, &acct->work_list);
+		return;
+	}
+
+	hash = io_get_work_hash(work);
+	tail = wqe->hash_tail[hash];
+	wqe->hash_tail[hash] = work;
+	if (!tail)
+		goto append;
+
+	wq_list_add_after(&work->list, &tail->list, &acct->work_list);
+}
+
+static bool io_wq_work_match_item(struct io_wq_work *work, void *data)
+{
+	return work == data;
+}
+
+static void io_wqe_enqueue(struct io_wqe *wqe, struct io_wq_work *work)
+{
+	struct io_wqe_acct *acct = io_work_get_acct(wqe, work);
+	unsigned work_flags = work->flags;
+	bool do_create;
+
+	/*
+	 * If io-wq is exiting for this task, or if the request has explicitly
+	 * been marked as one that should not get executed, cancel it here.
+	 */
+	if (test_bit(IO_WQ_BIT_EXIT, &wqe->wq->state) ||
+	    (work->flags & IO_WQ_WORK_CANCEL)) {
+		io_run_cancel(work, wqe);
+		return;
+	}
+
+	raw_spin_lock(&wqe->lock);
+	io_wqe_insert_work(wqe, work);
+	clear_bit(IO_ACCT_STALLED_BIT, &acct->flags);
+
+	rcu_read_lock();
+	do_create = !io_wqe_activate_free_worker(wqe, acct);
+	rcu_read_unlock();
+
+	raw_spin_unlock(&wqe->lock);
+
+	if (do_create && ((work_flags & IO_WQ_WORK_CONCURRENT) ||
+	    !atomic_read(&acct->nr_running))) {
+		bool did_create;
+
+		did_create = io_wqe_create_worker(wqe, acct);
+		if (likely(did_create))
+			return;
+
+		raw_spin_lock(&wqe->lock);
+		/* fatal condition, failed to create the first worker */
+		if (!acct->nr_workers) {
+			struct io_cb_cancel_data match = {
+				.fn		= io_wq_work_match_item,
+				.data		= work,
+				.cancel_all	= false,
+			};
+
+			if (io_acct_cancel_pending_work(wqe, acct, &match))
+				raw_spin_lock(&wqe->lock);
+		}
+		raw_spin_unlock(&wqe->lock);
+	}
+}
+
+void io_wq_enqueue(struct io_wq *wq, struct io_wq_work *work)
+{
+	struct io_wqe *wqe = wq->wqes[numa_node_id()];
+
+	io_wqe_enqueue(wqe, work);
+}
+
+/*
+ * Work items that hash to the same value will not be done in parallel.
+ * Used to limit concurrent writes, generally hashed by inode.
+ */
+void io_wq_hash_work(struct io_wq_work *work, void *val)
+{
+	unsigned int bit;
+
+	bit = hash_ptr(val, IO_WQ_HASH_ORDER);
+	work->flags |= (IO_WQ_WORK_HASHED | (bit << IO_WQ_HASH_SHIFT));
+}
+
+static bool io_wq_worker_cancel(struct io_worker *worker, void *data)
+{
+	struct io_cb_cancel_data *match = data;
+
+	/*
+	 * Hold the lock to avoid ->cur_work going out of scope, caller
+	 * may dereference the passed in work.
+	 */
+	spin_lock(&worker->lock);
+	if (worker->cur_work &&
+	    match->fn(worker->cur_work, match->data)) {
+		set_notify_signal(worker->task);
+		match->nr_running++;
+	}
+	spin_unlock(&worker->lock);
+
+	return match->nr_running && !match->cancel_all;
+}
+
+static inline void io_wqe_remove_pending(struct io_wqe *wqe,
+					 struct io_wq_work *work,
+					 struct io_wq_work_node *prev)
+{
+	struct io_wqe_acct *acct = io_work_get_acct(wqe, work);
+	unsigned int hash = io_get_work_hash(work);
+	struct io_wq_work *prev_work = NULL;
+
+	if (io_wq_is_hashed(work) && work == wqe->hash_tail[hash]) {
+		if (prev)
+			prev_work = container_of(prev, struct io_wq_work, list);
+		if (prev_work && io_get_work_hash(prev_work) == hash)
+			wqe->hash_tail[hash] = prev_work;
+		else
+			wqe->hash_tail[hash] = NULL;
+	}
+	wq_list_del(&acct->work_list, &work->list, prev);
+}
+
+static bool io_acct_cancel_pending_work(struct io_wqe *wqe,
+					struct io_wqe_acct *acct,
+					struct io_cb_cancel_data *match)
+	__releases(wqe->lock)
+{
+	struct io_wq_work_node *node, *prev;
+	struct io_wq_work *work;
+
+	wq_list_for_each(node, prev, &acct->work_list) {
+		work = container_of(node, struct io_wq_work, list);
+		if (!match->fn(work, match->data))
+			continue;
+		io_wqe_remove_pending(wqe, work, prev);
+		raw_spin_unlock(&wqe->lock);
+		io_run_cancel(work, wqe);
+		match->nr_pending++;
+		/* not safe to continue after unlock */
+		return true;
+	}
+
+	return false;
+}
+
+static void io_wqe_cancel_pending_work(struct io_wqe *wqe,
+				       struct io_cb_cancel_data *match)
+{
+	int i;
+retry:
+	raw_spin_lock(&wqe->lock);
+	for (i = 0; i < IO_WQ_ACCT_NR; i++) {
+		struct io_wqe_acct *acct = io_get_acct(wqe, i == 0);
+
+		if (io_acct_cancel_pending_work(wqe, acct, match)) {
+			if (match->cancel_all)
+				goto retry;
+			return;
+		}
+	}
+	raw_spin_unlock(&wqe->lock);
+}
+
+static void io_wqe_cancel_running_work(struct io_wqe *wqe,
+				       struct io_cb_cancel_data *match)
+{
+	rcu_read_lock();
+	io_wq_for_each_worker(wqe, io_wq_worker_cancel, match);
+	rcu_read_unlock();
+}
+
+enum io_wq_cancel io_wq_cancel_cb(struct io_wq *wq, work_cancel_fn *cancel,
+				  void *data, bool cancel_all)
+{
+	struct io_cb_cancel_data match = {
+		.fn		= cancel,
+		.data		= data,
+		.cancel_all	= cancel_all,
+	};
+	int node;
+
+	/*
+	 * First check pending list, if we're lucky we can just remove it
+	 * from there. CANCEL_OK means that the work is returned as-new,
+	 * no completion will be posted for it.
+	 */
+	for_each_node(node) {
+		struct io_wqe *wqe = wq->wqes[node];
+
+		io_wqe_cancel_pending_work(wqe, &match);
+		if (match.nr_pending && !match.cancel_all)
+			return IO_WQ_CANCEL_OK;
+	}
+
+	/*
+	 * Now check if a free (going busy) or busy worker has the work
+	 * currently running. If we find it there, we'll return CANCEL_RUNNING
+	 * as an indication that we attempt to signal cancellation. The
+	 * completion will run normally in this case.
+	 */
+	for_each_node(node) {
+		struct io_wqe *wqe = wq->wqes[node];
+
+		io_wqe_cancel_running_work(wqe, &match);
+		if (match.nr_running && !match.cancel_all)
+			return IO_WQ_CANCEL_RUNNING;
+	}
+
+	if (match.nr_running)
+		return IO_WQ_CANCEL_RUNNING;
+	if (match.nr_pending)
+		return IO_WQ_CANCEL_OK;
+	return IO_WQ_CANCEL_NOTFOUND;
+}
+
+static int io_wqe_hash_wake(struct wait_queue_entry *wait, unsigned mode,
+			    int sync, void *key)
+{
+	struct io_wqe *wqe = container_of(wait, struct io_wqe, wait);
+	int i;
+
+	list_del_init(&wait->entry);
+
+	rcu_read_lock();
+	for (i = 0; i < IO_WQ_ACCT_NR; i++) {
+		struct io_wqe_acct *acct = &wqe->acct[i];
+
+		if (test_and_clear_bit(IO_ACCT_STALLED_BIT, &acct->flags))
+			io_wqe_activate_free_worker(wqe, acct);
+	}
+	rcu_read_unlock();
+	return 1;
+}
+
+struct io_wq *io_wq_create(unsigned bounded, struct io_wq_data *data)
+{
+	int ret, node, i;
+	struct io_wq *wq;
+
+	if (WARN_ON_ONCE(!data->free_work || !data->do_work))
+		return ERR_PTR(-EINVAL);
+	if (WARN_ON_ONCE(!bounded))
+		return ERR_PTR(-EINVAL);
+
+	wq = kzalloc(struct_size(wq, wqes, nr_node_ids), GFP_KERNEL);
+	if (!wq)
+		return ERR_PTR(-ENOMEM);
+	ret = cpuhp_state_add_instance_nocalls(io_wq_online, &wq->cpuhp_node);
+	if (ret)
+		goto err_wq;
+
+	refcount_inc(&data->hash->refs);
+	wq->hash = data->hash;
+	wq->free_work = data->free_work;
+	wq->do_work = data->do_work;
+
+	ret = -ENOMEM;
+	for_each_node(node) {
+		struct io_wqe *wqe;
+		int alloc_node = node;
+
+		if (!node_online(alloc_node))
+			alloc_node = NUMA_NO_NODE;
+		wqe = kzalloc_node(sizeof(struct io_wqe), GFP_KERNEL, alloc_node);
+		if (!wqe)
+			goto err;
+		wq->wqes[node] = wqe;
+		if (!alloc_cpumask_var(&wqe->cpu_mask, GFP_KERNEL))
+			goto err;
+		cpumask_copy(wqe->cpu_mask, cpumask_of_node(node));
+		wqe->node = alloc_node;
+		wqe->acct[IO_WQ_ACCT_BOUND].max_workers = bounded;
+		wqe->acct[IO_WQ_ACCT_UNBOUND].max_workers =
+					task_rlimit(current, RLIMIT_NPROC);
+		INIT_LIST_HEAD(&wqe->wait.entry);
+		wqe->wait.func = io_wqe_hash_wake;
+		for (i = 0; i < IO_WQ_ACCT_NR; i++) {
+			struct io_wqe_acct *acct = &wqe->acct[i];
+
+			acct->index = i;
+			atomic_set(&acct->nr_running, 0);
+			INIT_WQ_LIST(&acct->work_list);
+		}
+		wqe->wq = wq;
+		raw_spin_lock_init(&wqe->lock);
+		INIT_HLIST_NULLS_HEAD(&wqe->free_list, 0);
+		INIT_LIST_HEAD(&wqe->all_list);
+	}
+
+	wq->task = get_task_struct(data->task);
+	atomic_set(&wq->worker_refs, 1);
+	init_completion(&wq->worker_done);
+	return wq;
+err:
+	io_wq_put_hash(data->hash);
+	cpuhp_state_remove_instance_nocalls(io_wq_online, &wq->cpuhp_node);
+	for_each_node(node) {
+		if (!wq->wqes[node])
+			continue;
+		free_cpumask_var(wq->wqes[node]->cpu_mask);
+		kfree(wq->wqes[node]);
+	}
+err_wq:
+	kfree(wq);
+	return ERR_PTR(ret);
+}
+
+static bool io_task_work_match(struct callback_head *cb, void *data)
+{
+	struct io_worker *worker;
+
+	if (cb->func != create_worker_cb && cb->func != create_worker_cont)
+		return false;
+	worker = container_of(cb, struct io_worker, create_work);
+	return worker->wqe->wq == data;
+}
+
+void io_wq_exit_start(struct io_wq *wq)
+{
+	set_bit(IO_WQ_BIT_EXIT, &wq->state);
+}
+
+static void io_wq_cancel_tw_create(struct io_wq *wq)
+{
+	struct callback_head *cb;
+
+	while ((cb = task_work_cancel_match(wq->task, io_task_work_match, wq)) != NULL) {
+		struct io_worker *worker;
+
+		worker = container_of(cb, struct io_worker, create_work);
+		io_worker_cancel_cb(worker);
+		/*
+		 * Only the worker continuation helper has worker allocated and
+		 * hence needs freeing.
+		 */
+		if (cb->func == create_worker_cont)
+			kfree(worker);
+	}
+}
+
+static void io_wq_exit_workers(struct io_wq *wq)
+{
+	int node;
+
+	if (!wq->task)
+		return;
+
+	io_wq_cancel_tw_create(wq);
+
+	rcu_read_lock();
+	for_each_node(node) {
+		struct io_wqe *wqe = wq->wqes[node];
+
+		io_wq_for_each_worker(wqe, io_wq_worker_wake, NULL);
+	}
+	rcu_read_unlock();
+	io_worker_ref_put(wq);
+	wait_for_completion(&wq->worker_done);
+
+	for_each_node(node) {
+		spin_lock_irq(&wq->hash->wait.lock);
+		list_del_init(&wq->wqes[node]->wait.entry);
+		spin_unlock_irq(&wq->hash->wait.lock);
+	}
+	put_task_struct(wq->task);
+	wq->task = NULL;
+}
+
+static void io_wq_destroy(struct io_wq *wq)
+{
+	int node;
+
+	cpuhp_state_remove_instance_nocalls(io_wq_online, &wq->cpuhp_node);
+
+	for_each_node(node) {
+		struct io_wqe *wqe = wq->wqes[node];
+		struct io_cb_cancel_data match = {
+			.fn		= io_wq_work_match_all,
+			.cancel_all	= true,
+		};
+		io_wqe_cancel_pending_work(wqe, &match);
+		free_cpumask_var(wqe->cpu_mask);
+		kfree(wqe);
+	}
+	io_wq_put_hash(wq->hash);
+	kfree(wq);
+}
+
+void io_wq_put_and_exit(struct io_wq *wq)
+{
+	WARN_ON_ONCE(!test_bit(IO_WQ_BIT_EXIT, &wq->state));
+
+	io_wq_exit_workers(wq);
+	io_wq_destroy(wq);
+}
+
+struct online_data {
+	unsigned int cpu;
+	bool online;
+};
+
+static bool io_wq_worker_affinity(struct io_worker *worker, void *data)
+{
+	struct online_data *od = data;
+
+	if (od->online)
+		cpumask_set_cpu(od->cpu, worker->wqe->cpu_mask);
+	else
+		cpumask_clear_cpu(od->cpu, worker->wqe->cpu_mask);
+	return false;
+}
+
+static int __io_wq_cpu_online(struct io_wq *wq, unsigned int cpu, bool online)
+{
+	struct online_data od = {
+		.cpu = cpu,
+		.online = online
+	};
+	int i;
+
+	rcu_read_lock();
+	for_each_node(i)
+		io_wq_for_each_worker(wq->wqes[i], io_wq_worker_affinity, &od);
+	rcu_read_unlock();
+	return 0;
+}
+
+static int io_wq_cpu_online(unsigned int cpu, struct hlist_node *node)
+{
+	struct io_wq *wq = hlist_entry_safe(node, struct io_wq, cpuhp_node);
+
+	return __io_wq_cpu_online(wq, cpu, true);
+}
+
+static int io_wq_cpu_offline(unsigned int cpu, struct hlist_node *node)
+{
+	struct io_wq *wq = hlist_entry_safe(node, struct io_wq, cpuhp_node);
+
+	return __io_wq_cpu_online(wq, cpu, false);
+}
+
+int io_wq_cpu_affinity(struct io_wq *wq, cpumask_var_t mask)
+{
+	int i;
+
+	rcu_read_lock();
+	for_each_node(i) {
+		struct io_wqe *wqe = wq->wqes[i];
+
+		if (mask)
+			cpumask_copy(wqe->cpu_mask, mask);
+		else
+			cpumask_copy(wqe->cpu_mask, cpumask_of_node(i));
+	}
+	rcu_read_unlock();
+	return 0;
+}
+
+/*
+ * Set max number of unbounded workers, returns old value. If new_count is 0,
+ * then just return the old value.
+ */
+int io_wq_max_workers(struct io_wq *wq, int *new_count)
+{
+	int prev[IO_WQ_ACCT_NR];
+	bool first_node = true;
+	int i, node;
+
+	BUILD_BUG_ON((int) IO_WQ_ACCT_BOUND   != (int) IO_WQ_BOUND);
+	BUILD_BUG_ON((int) IO_WQ_ACCT_UNBOUND != (int) IO_WQ_UNBOUND);
+	BUILD_BUG_ON((int) IO_WQ_ACCT_NR      != 2);
+
+	for (i = 0; i < 2; i++) {
+		if (new_count[i] > task_rlimit(current, RLIMIT_NPROC))
+			new_count[i] = task_rlimit(current, RLIMIT_NPROC);
+	}
+
+	for (i = 0; i < IO_WQ_ACCT_NR; i++)
+		prev[i] = 0;
+
+	rcu_read_lock();
+	for_each_node(node) {
+		struct io_wqe *wqe = wq->wqes[node];
+		struct io_wqe_acct *acct;
+
+		raw_spin_lock(&wqe->lock);
+		for (i = 0; i < IO_WQ_ACCT_NR; i++) {
+			acct = &wqe->acct[i];
+			if (first_node)
+				prev[i] = max_t(int, acct->max_workers, prev[i]);
+			if (new_count[i])
+				acct->max_workers = new_count[i];
+		}
+		raw_spin_unlock(&wqe->lock);
+		first_node = false;
+	}
+	rcu_read_unlock();
+
+	for (i = 0; i < IO_WQ_ACCT_NR; i++)
+		new_count[i] = prev[i];
+
+	return 0;
+}
+
+static __init int io_wq_init(void)
+{
+	int ret;
+
+	ret = cpuhp_setup_state_multi(CPUHP_AP_ONLINE_DYN, "io-wq/online",
+					io_wq_cpu_online, io_wq_cpu_offline);
+	if (ret < 0)
+		return ret;
+	io_wq_online = ret;
+	return 0;
+}
+subsys_initcall(io_wq_init);
--- linux-xilinx-zynqmp-5.15.0.orig/io_uring/io-wq.h
+++ linux-xilinx-zynqmp-5.15.0/io_uring/io-wq.h
@@ -0,0 +1,161 @@
+#ifndef INTERNAL_IO_WQ_H
+#define INTERNAL_IO_WQ_H
+
+#include <linux/refcount.h>
+
+struct io_wq;
+
+enum {
+	IO_WQ_WORK_CANCEL	= 1,
+	IO_WQ_WORK_HASHED	= 2,
+	IO_WQ_WORK_UNBOUND	= 4,
+	IO_WQ_WORK_CONCURRENT	= 16,
+
+	IO_WQ_HASH_SHIFT	= 24,	/* upper 8 bits are used for hash key */
+};
+
+enum io_wq_cancel {
+	IO_WQ_CANCEL_OK,	/* cancelled before started */
+	IO_WQ_CANCEL_RUNNING,	/* found, running, and attempted cancelled */
+	IO_WQ_CANCEL_NOTFOUND,	/* work not found */
+};
+
+struct io_wq_work_node {
+	struct io_wq_work_node *next;
+};
+
+struct io_wq_work_list {
+	struct io_wq_work_node *first;
+	struct io_wq_work_node *last;
+};
+
+static inline void wq_list_add_after(struct io_wq_work_node *node,
+				     struct io_wq_work_node *pos,
+				     struct io_wq_work_list *list)
+{
+	struct io_wq_work_node *next = pos->next;
+
+	pos->next = node;
+	node->next = next;
+	if (!next)
+		list->last = node;
+}
+
+static inline void wq_list_add_tail(struct io_wq_work_node *node,
+				    struct io_wq_work_list *list)
+{
+	node->next = NULL;
+	if (!list->first) {
+		list->last = node;
+		WRITE_ONCE(list->first, node);
+	} else {
+		list->last->next = node;
+		list->last = node;
+	}
+}
+
+static inline void wq_list_cut(struct io_wq_work_list *list,
+			       struct io_wq_work_node *last,
+			       struct io_wq_work_node *prev)
+{
+	/* first in the list, if prev==NULL */
+	if (!prev)
+		WRITE_ONCE(list->first, last->next);
+	else
+		prev->next = last->next;
+
+	if (last == list->last)
+		list->last = prev;
+	last->next = NULL;
+}
+
+static inline void wq_list_del(struct io_wq_work_list *list,
+			       struct io_wq_work_node *node,
+			       struct io_wq_work_node *prev)
+{
+	wq_list_cut(list, node, prev);
+}
+
+#define wq_list_for_each(pos, prv, head)			\
+	for (pos = (head)->first, prv = NULL; pos; prv = pos, pos = (pos)->next)
+
+#define wq_list_empty(list)	(READ_ONCE((list)->first) == NULL)
+#define INIT_WQ_LIST(list)	do {				\
+	(list)->first = NULL;					\
+	(list)->last = NULL;					\
+} while (0)
+
+struct io_wq_work {
+	struct io_wq_work_node list;
+	unsigned flags;
+};
+
+static inline struct io_wq_work *wq_next_work(struct io_wq_work *work)
+{
+	if (!work->list.next)
+		return NULL;
+
+	return container_of(work->list.next, struct io_wq_work, list);
+}
+
+typedef struct io_wq_work *(free_work_fn)(struct io_wq_work *);
+typedef void (io_wq_work_fn)(struct io_wq_work *);
+
+struct io_wq_hash {
+	refcount_t refs;
+	unsigned long map;
+	struct wait_queue_head wait;
+};
+
+static inline void io_wq_put_hash(struct io_wq_hash *hash)
+{
+	if (refcount_dec_and_test(&hash->refs))
+		kfree(hash);
+}
+
+struct io_wq_data {
+	struct io_wq_hash *hash;
+	struct task_struct *task;
+	io_wq_work_fn *do_work;
+	free_work_fn *free_work;
+};
+
+struct io_wq *io_wq_create(unsigned bounded, struct io_wq_data *data);
+void io_wq_exit_start(struct io_wq *wq);
+void io_wq_put_and_exit(struct io_wq *wq);
+
+void io_wq_enqueue(struct io_wq *wq, struct io_wq_work *work);
+void io_wq_hash_work(struct io_wq_work *work, void *val);
+
+int io_wq_cpu_affinity(struct io_wq *wq, cpumask_var_t mask);
+int io_wq_max_workers(struct io_wq *wq, int *new_count);
+bool io_wq_worker_stopped(void);
+
+static inline bool io_wq_is_hashed(struct io_wq_work *work)
+{
+	return work->flags & IO_WQ_WORK_HASHED;
+}
+
+typedef bool (work_cancel_fn)(struct io_wq_work *, void *);
+
+enum io_wq_cancel io_wq_cancel_cb(struct io_wq *wq, work_cancel_fn *cancel,
+					void *data, bool cancel_all);
+
+#if defined(CONFIG_IO_WQ)
+extern void io_wq_worker_sleeping(struct task_struct *);
+extern void io_wq_worker_running(struct task_struct *);
+#else
+static inline void io_wq_worker_sleeping(struct task_struct *tsk)
+{
+}
+static inline void io_wq_worker_running(struct task_struct *tsk)
+{
+}
+#endif
+
+static inline bool io_wq_current_is_worker(void)
+{
+	return in_task() && (current->flags & PF_IO_WORKER) &&
+		current->pf_io_worker;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/io_uring/io_uring.c
+++ linux-xilinx-zynqmp-5.15.0/io_uring/io_uring.c
@@ -0,0 +1,11195 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Shared application/kernel submission and completion ring pairs, for
+ * supporting fast/efficient IO.
+ *
+ * A note on the read/write ordering memory barriers that are matched between
+ * the application and kernel side.
+ *
+ * After the application reads the CQ ring tail, it must use an
+ * appropriate smp_rmb() to pair with the smp_wmb() the kernel uses
+ * before writing the tail (using smp_load_acquire to read the tail will
+ * do). It also needs a smp_mb() before updating CQ head (ordering the
+ * entry load(s) with the head store), pairing with an implicit barrier
+ * through a control-dependency in io_get_cqe (smp_store_release to
+ * store head will do). Failure to do so could lead to reading invalid
+ * CQ entries.
+ *
+ * Likewise, the application must use an appropriate smp_wmb() before
+ * writing the SQ tail (ordering SQ entry stores with the tail store),
+ * which pairs with smp_load_acquire in io_get_sqring (smp_store_release
+ * to store the tail will do). And it needs a barrier ordering the SQ
+ * head load before writing new SQ entries (smp_load_acquire to read
+ * head will do).
+ *
+ * When using the SQ poll thread (IORING_SETUP_SQPOLL), the application
+ * needs to check the SQ flags for IORING_SQ_NEED_WAKEUP *after*
+ * updating the SQ tail; a full memory barrier smp_mb() is needed
+ * between.
+ *
+ * Also see the examples in the liburing library:
+ *
+ *	git://git.kernel.dk/liburing
+ *
+ * io_uring also uses READ/WRITE_ONCE() for _any_ store or load that happens
+ * from data shared between the kernel and application. This is done both
+ * for ordering purposes, but also to ensure that once a value is loaded from
+ * data that the application could potentially modify, it remains stable.
+ *
+ * Copyright (C) 2018-2019 Jens Axboe
+ * Copyright (c) 2018-2019 Christoph Hellwig
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/syscalls.h>
+#include <linux/compat.h>
+#include <net/compat.h>
+#include <linux/refcount.h>
+#include <linux/uio.h>
+#include <linux/bits.h>
+
+#include <linux/sched/signal.h>
+#include <linux/fs.h>
+#include <linux/file.h>
+#include <linux/fdtable.h>
+#include <linux/mm.h>
+#include <linux/mman.h>
+#include <linux/percpu.h>
+#include <linux/cpuset.h>
+#include <linux/slab.h>
+#include <linux/blkdev.h>
+#include <linux/bvec.h>
+#include <linux/net.h>
+#include <net/sock.h>
+#include <net/af_unix.h>
+#include <linux/anon_inodes.h>
+#include <linux/sched/mm.h>
+#include <linux/uaccess.h>
+#include <linux/nospec.h>
+#include <linux/sizes.h>
+#include <linux/hugetlb.h>
+#include <linux/highmem.h>
+#include <linux/namei.h>
+#include <linux/fsnotify.h>
+#include <linux/fadvise.h>
+#include <linux/eventpoll.h>
+#include <linux/splice.h>
+#include <linux/task_work.h>
+#include <linux/pagemap.h>
+#include <linux/io_uring.h>
+#include <linux/tracehook.h>
+
+#define CREATE_TRACE_POINTS
+#include <trace/events/io_uring.h>
+
+#include <uapi/linux/io_uring.h>
+
+#include "../fs/internal.h"
+#include "io-wq.h"
+
+#define IORING_MAX_ENTRIES	32768
+#define IORING_MAX_CQ_ENTRIES	(2 * IORING_MAX_ENTRIES)
+#define IORING_SQPOLL_CAP_ENTRIES_VALUE 8
+
+/* only define max */
+#define IORING_MAX_FIXED_FILES	(1U << 15)
+#define IORING_MAX_RESTRICTIONS	(IORING_RESTRICTION_LAST + \
+				 IORING_REGISTER_LAST + IORING_OP_LAST)
+
+#define IO_RSRC_TAG_TABLE_SHIFT	(PAGE_SHIFT - 3)
+#define IO_RSRC_TAG_TABLE_MAX	(1U << IO_RSRC_TAG_TABLE_SHIFT)
+#define IO_RSRC_TAG_TABLE_MASK	(IO_RSRC_TAG_TABLE_MAX - 1)
+
+#define IORING_MAX_REG_BUFFERS	(1U << 14)
+
+#define SQE_VALID_FLAGS	(IOSQE_FIXED_FILE|IOSQE_IO_DRAIN|IOSQE_IO_LINK|	\
+				IOSQE_IO_HARDLINK | IOSQE_ASYNC | \
+				IOSQE_BUFFER_SELECT)
+#define IO_REQ_CLEAN_FLAGS (REQ_F_BUFFER_SELECTED | REQ_F_NEED_CLEANUP | \
+				REQ_F_POLLED | REQ_F_INFLIGHT | REQ_F_CREDS)
+
+#define IO_TCTX_REFS_CACHE_NR	(1U << 10)
+
+struct io_uring {
+	u32 head ____cacheline_aligned_in_smp;
+	u32 tail ____cacheline_aligned_in_smp;
+};
+
+/*
+ * This data is shared with the application through the mmap at offsets
+ * IORING_OFF_SQ_RING and IORING_OFF_CQ_RING.
+ *
+ * The offsets to the member fields are published through struct
+ * io_sqring_offsets when calling io_uring_setup.
+ */
+struct io_rings {
+	/*
+	 * Head and tail offsets into the ring; the offsets need to be
+	 * masked to get valid indices.
+	 *
+	 * The kernel controls head of the sq ring and the tail of the cq ring,
+	 * and the application controls tail of the sq ring and the head of the
+	 * cq ring.
+	 */
+	struct io_uring		sq, cq;
+	/*
+	 * Bitmasks to apply to head and tail offsets (constant, equals
+	 * ring_entries - 1)
+	 */
+	u32			sq_ring_mask, cq_ring_mask;
+	/* Ring sizes (constant, power of 2) */
+	u32			sq_ring_entries, cq_ring_entries;
+	/*
+	 * Number of invalid entries dropped by the kernel due to
+	 * invalid index stored in array
+	 *
+	 * Written by the kernel, shouldn't be modified by the
+	 * application (i.e. get number of "new events" by comparing to
+	 * cached value).
+	 *
+	 * After a new SQ head value was read by the application this
+	 * counter includes all submissions that were dropped reaching
+	 * the new SQ head (and possibly more).
+	 */
+	u32			sq_dropped;
+	/*
+	 * Runtime SQ flags
+	 *
+	 * Written by the kernel, shouldn't be modified by the
+	 * application.
+	 *
+	 * The application needs a full memory barrier before checking
+	 * for IORING_SQ_NEED_WAKEUP after updating the sq tail.
+	 */
+	u32			sq_flags;
+	/*
+	 * Runtime CQ flags
+	 *
+	 * Written by the application, shouldn't be modified by the
+	 * kernel.
+	 */
+	u32			cq_flags;
+	/*
+	 * Number of completion events lost because the queue was full;
+	 * this should be avoided by the application by making sure
+	 * there are not more requests pending than there is space in
+	 * the completion queue.
+	 *
+	 * Written by the kernel, shouldn't be modified by the
+	 * application (i.e. get number of "new events" by comparing to
+	 * cached value).
+	 *
+	 * As completion events come in out of order this counter is not
+	 * ordered with any other data.
+	 */
+	u32			cq_overflow;
+	/*
+	 * Ring buffer of completion events.
+	 *
+	 * The kernel writes completion events fresh every time they are
+	 * produced, so the application is allowed to modify pending
+	 * entries.
+	 */
+	struct io_uring_cqe	cqes[] ____cacheline_aligned_in_smp;
+};
+
+enum io_uring_cmd_flags {
+	IO_URING_F_NONBLOCK		= 1,
+	IO_URING_F_COMPLETE_DEFER	= 2,
+};
+
+struct io_mapped_ubuf {
+	u64		ubuf;
+	u64		ubuf_end;
+	unsigned int	nr_bvecs;
+	unsigned long	acct_pages;
+	struct bio_vec	bvec[];
+};
+
+struct io_ring_ctx;
+
+struct io_overflow_cqe {
+	struct io_uring_cqe cqe;
+	struct list_head list;
+};
+
+struct io_fixed_file {
+	/* file * with additional FFS_* flags */
+	unsigned long file_ptr;
+};
+
+struct io_rsrc_put {
+	struct list_head list;
+	u64 tag;
+	union {
+		void *rsrc;
+		struct file *file;
+		struct io_mapped_ubuf *buf;
+	};
+};
+
+struct io_file_table {
+	struct io_fixed_file *files;
+};
+
+struct io_rsrc_node {
+	struct percpu_ref		refs;
+	struct list_head		node;
+	struct list_head		rsrc_list;
+	struct io_rsrc_data		*rsrc_data;
+	struct llist_node		llist;
+	bool				done;
+};
+
+typedef void (rsrc_put_fn)(struct io_ring_ctx *ctx, struct io_rsrc_put *prsrc);
+
+struct io_rsrc_data {
+	struct io_ring_ctx		*ctx;
+
+	u64				**tags;
+	unsigned int			nr;
+	rsrc_put_fn			*do_put;
+	atomic_t			refs;
+	struct completion		done;
+	bool				quiesce;
+};
+
+struct io_buffer {
+	struct list_head list;
+	__u64 addr;
+	__u32 len;
+	__u16 bid;
+};
+
+struct io_restriction {
+	DECLARE_BITMAP(register_op, IORING_REGISTER_LAST);
+	DECLARE_BITMAP(sqe_op, IORING_OP_LAST);
+	u8 sqe_flags_allowed;
+	u8 sqe_flags_required;
+	bool registered;
+};
+
+enum {
+	IO_SQ_THREAD_SHOULD_STOP = 0,
+	IO_SQ_THREAD_SHOULD_PARK,
+};
+
+struct io_sq_data {
+	refcount_t		refs;
+	atomic_t		park_pending;
+	struct mutex		lock;
+
+	/* ctx's that are using this sqd */
+	struct list_head	ctx_list;
+
+	struct task_struct	*thread;
+	struct wait_queue_head	wait;
+
+	unsigned		sq_thread_idle;
+	int			sq_cpu;
+	pid_t			task_pid;
+	pid_t			task_tgid;
+
+	unsigned long		state;
+	struct completion	exited;
+};
+
+#define IO_COMPL_BATCH			32
+#define IO_REQ_CACHE_SIZE		32
+#define IO_REQ_ALLOC_BATCH		8
+
+struct io_submit_link {
+	struct io_kiocb		*head;
+	struct io_kiocb		*last;
+};
+
+struct io_submit_state {
+	struct blk_plug		plug;
+	struct io_submit_link	link;
+
+	/*
+	 * io_kiocb alloc cache
+	 */
+	void			*reqs[IO_REQ_CACHE_SIZE];
+	unsigned int		free_reqs;
+
+	bool			plug_started;
+
+	/*
+	 * Batch completion logic
+	 */
+	struct io_kiocb		*compl_reqs[IO_COMPL_BATCH];
+	unsigned int		compl_nr;
+	/* inline/task_work completion list, under ->uring_lock */
+	struct list_head	free_list;
+
+	unsigned int		ios_left;
+};
+
+struct io_ring_ctx {
+	/* const or read-mostly hot data */
+	struct {
+		struct percpu_ref	refs;
+
+		struct io_rings		*rings;
+		unsigned int		flags;
+		unsigned int		compat: 1;
+		unsigned int		drain_next: 1;
+		unsigned int		eventfd_async: 1;
+		unsigned int		restricted: 1;
+		unsigned int		off_timeout_used: 1;
+		unsigned int		drain_active: 1;
+	} ____cacheline_aligned_in_smp;
+
+	/* submission data */
+	struct {
+		struct mutex		uring_lock;
+
+		/*
+		 * Ring buffer of indices into array of io_uring_sqe, which is
+		 * mmapped by the application using the IORING_OFF_SQES offset.
+		 *
+		 * This indirection could e.g. be used to assign fixed
+		 * io_uring_sqe entries to operations and only submit them to
+		 * the queue when needed.
+		 *
+		 * The kernel modifies neither the indices array nor the entries
+		 * array.
+		 */
+		u32			*sq_array;
+		struct io_uring_sqe	*sq_sqes;
+		unsigned		cached_sq_head;
+		unsigned		sq_entries;
+		struct list_head	defer_list;
+
+		/*
+		 * Fixed resources fast path, should be accessed only under
+		 * uring_lock, and updated through io_uring_register(2)
+		 */
+		struct io_rsrc_node	*rsrc_node;
+		struct io_file_table	file_table;
+		unsigned		nr_user_files;
+		unsigned		nr_user_bufs;
+		struct io_mapped_ubuf	**user_bufs;
+
+		struct io_submit_state	submit_state;
+		struct list_head	timeout_list;
+		struct list_head	ltimeout_list;
+		struct list_head	cq_overflow_list;
+		struct xarray		io_buffers;
+		struct xarray		personalities;
+		u32			pers_next;
+		unsigned		sq_thread_idle;
+	} ____cacheline_aligned_in_smp;
+
+	/* IRQ completion list, under ->completion_lock */
+	struct list_head	locked_free_list;
+	unsigned int		locked_free_nr;
+
+	const struct cred	*sq_creds;	/* cred used for __io_sq_thread() */
+	struct io_sq_data	*sq_data;	/* if using sq thread polling */
+
+	struct wait_queue_head	sqo_sq_wait;
+	struct list_head	sqd_list;
+
+	unsigned long		check_cq_overflow;
+
+	struct {
+		unsigned		cached_cq_tail;
+		unsigned		cq_entries;
+		struct eventfd_ctx	*cq_ev_fd;
+		struct wait_queue_head	poll_wait;
+		struct wait_queue_head	cq_wait;
+		unsigned		cq_extra;
+		atomic_t		cq_timeouts;
+		unsigned		cq_last_tm_flush;
+	} ____cacheline_aligned_in_smp;
+
+	struct {
+		spinlock_t		completion_lock;
+
+		spinlock_t		timeout_lock;
+
+		/*
+		 * ->iopoll_list is protected by the ctx->uring_lock for
+		 * io_uring instances that don't use IORING_SETUP_SQPOLL.
+		 * For SQPOLL, only the single threaded io_sq_thread() will
+		 * manipulate the list, hence no extra locking is needed there.
+		 */
+		struct list_head	iopoll_list;
+		struct hlist_head	*cancel_hash;
+		unsigned		cancel_hash_bits;
+		bool			poll_multi_queue;
+	} ____cacheline_aligned_in_smp;
+
+	struct io_restriction		restrictions;
+
+	/* slow path rsrc auxilary data, used by update/register */
+	struct {
+		struct io_rsrc_node		*rsrc_backup_node;
+		struct io_mapped_ubuf		*dummy_ubuf;
+		struct io_rsrc_data		*file_data;
+		struct io_rsrc_data		*buf_data;
+
+		struct delayed_work		rsrc_put_work;
+		struct llist_head		rsrc_put_llist;
+		struct list_head		rsrc_ref_list;
+		spinlock_t			rsrc_ref_lock;
+	};
+
+	/* Keep this last, we don't need it for the fast path */
+	struct {
+		/* hashed buffered write serialization */
+		struct io_wq_hash		*hash_map;
+
+		/* Only used for accounting purposes */
+		struct user_struct		*user;
+		struct mm_struct		*mm_account;
+
+		/* ctx exit and cancelation */
+		struct llist_head		fallback_llist;
+		struct delayed_work		fallback_work;
+		struct work_struct		exit_work;
+		struct list_head		tctx_list;
+		struct completion		ref_comp;
+		u32				iowq_limits[2];
+		bool				iowq_limits_set;
+	};
+};
+
+struct io_uring_task {
+	/* submission side */
+	int			cached_refs;
+	struct xarray		xa;
+	struct wait_queue_head	wait;
+	const struct io_ring_ctx *last;
+	struct io_wq		*io_wq;
+	struct percpu_counter	inflight;
+	atomic_t		inflight_tracked;
+	atomic_t		in_idle;
+
+	spinlock_t		task_lock;
+	struct io_wq_work_list	task_list;
+	struct callback_head	task_work;
+	bool			task_running;
+};
+
+/*
+ * First field must be the file pointer in all the
+ * iocb unions! See also 'struct kiocb' in <linux/fs.h>
+ */
+struct io_poll_iocb {
+	struct file			*file;
+	struct wait_queue_head		*head;
+	__poll_t			events;
+	int				retries;
+	struct wait_queue_entry		wait;
+};
+
+struct io_poll_update {
+	struct file			*file;
+	u64				old_user_data;
+	u64				new_user_data;
+	__poll_t			events;
+	bool				update_events;
+	bool				update_user_data;
+};
+
+struct io_close {
+	struct file			*file;
+	int				fd;
+	u32				file_slot;
+};
+
+struct io_timeout_data {
+	struct io_kiocb			*req;
+	struct hrtimer			timer;
+	struct timespec64		ts;
+	enum hrtimer_mode		mode;
+	u32				flags;
+};
+
+struct io_accept {
+	struct file			*file;
+	struct sockaddr __user		*addr;
+	int __user			*addr_len;
+	int				flags;
+	u32				file_slot;
+	unsigned long			nofile;
+};
+
+struct io_sync {
+	struct file			*file;
+	loff_t				len;
+	loff_t				off;
+	int				flags;
+	int				mode;
+};
+
+struct io_cancel {
+	struct file			*file;
+	u64				addr;
+};
+
+struct io_timeout {
+	struct file			*file;
+	u32				off;
+	u32				target_seq;
+	struct list_head		list;
+	/* head of the link, used by linked timeouts only */
+	struct io_kiocb			*head;
+	/* for linked completions */
+	struct io_kiocb			*prev;
+};
+
+struct io_timeout_rem {
+	struct file			*file;
+	u64				addr;
+
+	/* timeout update */
+	struct timespec64		ts;
+	u32				flags;
+	bool				ltimeout;
+};
+
+struct io_rw {
+	/* NOTE: kiocb has the file as the first member, so don't do it here */
+	struct kiocb			kiocb;
+	u64				addr;
+	u64				len;
+};
+
+struct io_connect {
+	struct file			*file;
+	struct sockaddr __user		*addr;
+	int				addr_len;
+};
+
+struct io_sr_msg {
+	struct file			*file;
+	union {
+		struct compat_msghdr __user	*umsg_compat;
+		struct user_msghdr __user	*umsg;
+		void __user			*buf;
+	};
+	int				msg_flags;
+	int				bgid;
+	size_t				len;
+	size_t				done_io;
+	struct io_buffer		*kbuf;
+	void __user			*msg_control;
+};
+
+struct io_open {
+	struct file			*file;
+	int				dfd;
+	u32				file_slot;
+	struct filename			*filename;
+	struct open_how			how;
+	unsigned long			nofile;
+};
+
+struct io_rsrc_update {
+	struct file			*file;
+	u64				arg;
+	u32				nr_args;
+	u32				offset;
+};
+
+struct io_fadvise {
+	struct file			*file;
+	u64				offset;
+	u32				len;
+	u32				advice;
+};
+
+struct io_madvise {
+	struct file			*file;
+	u64				addr;
+	u32				len;
+	u32				advice;
+};
+
+struct io_epoll {
+	struct file			*file;
+	int				epfd;
+	int				op;
+	int				fd;
+	struct epoll_event		event;
+};
+
+struct io_splice {
+	struct file			*file_out;
+	loff_t				off_out;
+	loff_t				off_in;
+	u64				len;
+	int				splice_fd_in;
+	unsigned int			flags;
+};
+
+struct io_provide_buf {
+	struct file			*file;
+	__u64				addr;
+	__u32				len;
+	__u32				bgid;
+	__u16				nbufs;
+	__u16				bid;
+};
+
+struct io_statx {
+	struct file			*file;
+	int				dfd;
+	unsigned int			mask;
+	unsigned int			flags;
+	const char __user		*filename;
+	struct statx __user		*buffer;
+};
+
+struct io_shutdown {
+	struct file			*file;
+	int				how;
+};
+
+struct io_rename {
+	struct file			*file;
+	int				old_dfd;
+	int				new_dfd;
+	struct filename			*oldpath;
+	struct filename			*newpath;
+	int				flags;
+};
+
+struct io_unlink {
+	struct file			*file;
+	int				dfd;
+	int				flags;
+	struct filename			*filename;
+};
+
+struct io_mkdir {
+	struct file			*file;
+	int				dfd;
+	umode_t				mode;
+	struct filename			*filename;
+};
+
+struct io_symlink {
+	struct file			*file;
+	int				new_dfd;
+	struct filename			*oldpath;
+	struct filename			*newpath;
+};
+
+struct io_hardlink {
+	struct file			*file;
+	int				old_dfd;
+	int				new_dfd;
+	struct filename			*oldpath;
+	struct filename			*newpath;
+	int				flags;
+};
+
+struct io_completion {
+	struct file			*file;
+	u32				cflags;
+};
+
+struct io_async_connect {
+	struct sockaddr_storage		address;
+};
+
+struct io_async_msghdr {
+	struct iovec			fast_iov[UIO_FASTIOV];
+	/* points to an allocated iov, if NULL we use fast_iov instead */
+	struct iovec			*free_iov;
+	struct sockaddr __user		*uaddr;
+	struct msghdr			msg;
+	struct sockaddr_storage		addr;
+};
+
+struct io_async_rw {
+	struct iovec			fast_iov[UIO_FASTIOV];
+	const struct iovec		*free_iovec;
+	struct iov_iter			iter;
+	struct iov_iter_state		iter_state;
+	size_t				bytes_done;
+	struct wait_page_queue		wpq;
+};
+
+enum {
+	REQ_F_FIXED_FILE_BIT	= IOSQE_FIXED_FILE_BIT,
+	REQ_F_IO_DRAIN_BIT	= IOSQE_IO_DRAIN_BIT,
+	REQ_F_LINK_BIT		= IOSQE_IO_LINK_BIT,
+	REQ_F_HARDLINK_BIT	= IOSQE_IO_HARDLINK_BIT,
+	REQ_F_FORCE_ASYNC_BIT	= IOSQE_ASYNC_BIT,
+	REQ_F_BUFFER_SELECT_BIT	= IOSQE_BUFFER_SELECT_BIT,
+
+	/* first byte is taken by user flags, shift it to not overlap */
+	REQ_F_FAIL_BIT		= 8,
+	REQ_F_INFLIGHT_BIT,
+	REQ_F_CUR_POS_BIT,
+	REQ_F_NOWAIT_BIT,
+	REQ_F_LINK_TIMEOUT_BIT,
+	REQ_F_NEED_CLEANUP_BIT,
+	REQ_F_POLLED_BIT,
+	REQ_F_BUFFER_SELECTED_BIT,
+	REQ_F_COMPLETE_INLINE_BIT,
+	REQ_F_REISSUE_BIT,
+	REQ_F_CREDS_BIT,
+	REQ_F_REFCOUNT_BIT,
+	REQ_F_ARM_LTIMEOUT_BIT,
+	REQ_F_PARTIAL_IO_BIT,
+	/* keep async read/write and isreg together and in order */
+	REQ_F_NOWAIT_READ_BIT,
+	REQ_F_NOWAIT_WRITE_BIT,
+	REQ_F_ISREG_BIT,
+
+	/* not a real bit, just to check we're not overflowing the space */
+	__REQ_F_LAST_BIT,
+};
+
+enum {
+	/* ctx owns file */
+	REQ_F_FIXED_FILE	= BIT(REQ_F_FIXED_FILE_BIT),
+	/* drain existing IO first */
+	REQ_F_IO_DRAIN		= BIT(REQ_F_IO_DRAIN_BIT),
+	/* linked sqes */
+	REQ_F_LINK		= BIT(REQ_F_LINK_BIT),
+	/* doesn't sever on completion < 0 */
+	REQ_F_HARDLINK		= BIT(REQ_F_HARDLINK_BIT),
+	/* IOSQE_ASYNC */
+	REQ_F_FORCE_ASYNC	= BIT(REQ_F_FORCE_ASYNC_BIT),
+	/* IOSQE_BUFFER_SELECT */
+	REQ_F_BUFFER_SELECT	= BIT(REQ_F_BUFFER_SELECT_BIT),
+
+	/* fail rest of links */
+	REQ_F_FAIL		= BIT(REQ_F_FAIL_BIT),
+	/* on inflight list, should be cancelled and waited on exit reliably */
+	REQ_F_INFLIGHT		= BIT(REQ_F_INFLIGHT_BIT),
+	/* read/write uses file position */
+	REQ_F_CUR_POS		= BIT(REQ_F_CUR_POS_BIT),
+	/* must not punt to workers */
+	REQ_F_NOWAIT		= BIT(REQ_F_NOWAIT_BIT),
+	/* has or had linked timeout */
+	REQ_F_LINK_TIMEOUT	= BIT(REQ_F_LINK_TIMEOUT_BIT),
+	/* needs cleanup */
+	REQ_F_NEED_CLEANUP	= BIT(REQ_F_NEED_CLEANUP_BIT),
+	/* already went through poll handler */
+	REQ_F_POLLED		= BIT(REQ_F_POLLED_BIT),
+	/* buffer already selected */
+	REQ_F_BUFFER_SELECTED	= BIT(REQ_F_BUFFER_SELECTED_BIT),
+	/* completion is deferred through io_comp_state */
+	REQ_F_COMPLETE_INLINE	= BIT(REQ_F_COMPLETE_INLINE_BIT),
+	/* caller should reissue async */
+	REQ_F_REISSUE		= BIT(REQ_F_REISSUE_BIT),
+	/* supports async reads */
+	REQ_F_NOWAIT_READ	= BIT(REQ_F_NOWAIT_READ_BIT),
+	/* supports async writes */
+	REQ_F_NOWAIT_WRITE	= BIT(REQ_F_NOWAIT_WRITE_BIT),
+	/* regular file */
+	REQ_F_ISREG		= BIT(REQ_F_ISREG_BIT),
+	/* has creds assigned */
+	REQ_F_CREDS		= BIT(REQ_F_CREDS_BIT),
+	/* skip refcounting if not set */
+	REQ_F_REFCOUNT		= BIT(REQ_F_REFCOUNT_BIT),
+	/* there is a linked timeout that has to be armed */
+	REQ_F_ARM_LTIMEOUT	= BIT(REQ_F_ARM_LTIMEOUT_BIT),
+	/* request has already done partial IO */
+	REQ_F_PARTIAL_IO	= BIT(REQ_F_PARTIAL_IO_BIT),
+};
+
+struct async_poll {
+	struct io_poll_iocb	poll;
+	struct io_poll_iocb	*double_poll;
+};
+
+typedef void (*io_req_tw_func_t)(struct io_kiocb *req, bool *locked);
+
+struct io_task_work {
+	union {
+		struct io_wq_work_node	node;
+		struct llist_node	fallback_node;
+	};
+	io_req_tw_func_t		func;
+};
+
+enum {
+	IORING_RSRC_FILE		= 0,
+	IORING_RSRC_BUFFER		= 1,
+};
+
+/*
+ * NOTE! Each of the iocb union members has the file pointer
+ * as the first entry in their struct definition. So you can
+ * access the file pointer through any of the sub-structs,
+ * or directly as just 'ki_filp' in this struct.
+ */
+struct io_kiocb {
+	union {
+		struct file		*file;
+		struct io_rw		rw;
+		struct io_poll_iocb	poll;
+		struct io_poll_update	poll_update;
+		struct io_accept	accept;
+		struct io_sync		sync;
+		struct io_cancel	cancel;
+		struct io_timeout	timeout;
+		struct io_timeout_rem	timeout_rem;
+		struct io_connect	connect;
+		struct io_sr_msg	sr_msg;
+		struct io_open		open;
+		struct io_close		close;
+		struct io_rsrc_update	rsrc_update;
+		struct io_fadvise	fadvise;
+		struct io_madvise	madvise;
+		struct io_epoll		epoll;
+		struct io_splice	splice;
+		struct io_provide_buf	pbuf;
+		struct io_statx		statx;
+		struct io_shutdown	shutdown;
+		struct io_rename	rename;
+		struct io_unlink	unlink;
+		struct io_mkdir		mkdir;
+		struct io_symlink	symlink;
+		struct io_hardlink	hardlink;
+		/* use only after cleaning per-op data, see io_clean_op() */
+		struct io_completion	compl;
+	};
+
+	/* opcode allocated if it needs to store data for async defer */
+	void				*async_data;
+	u8				opcode;
+	/* polled IO has completed */
+	u8				iopoll_completed;
+
+	u16				buf_index;
+	u32				result;
+
+	struct io_ring_ctx		*ctx;
+	unsigned int			flags;
+	atomic_t			refs;
+	struct task_struct		*task;
+	u64				user_data;
+
+	struct io_kiocb			*link;
+	struct percpu_ref		*fixed_rsrc_refs;
+
+	/* used with ctx->iopoll_list with reads/writes */
+	struct list_head		inflight_entry;
+	struct io_task_work		io_task_work;
+	/* for polled requests, i.e. IORING_OP_POLL_ADD and async armed poll */
+	struct hlist_node		hash_node;
+	struct async_poll		*apoll;
+	struct io_wq_work		work;
+	const struct cred		*creds;
+
+	/* store used ubuf, so we can prevent reloading */
+	struct io_mapped_ubuf		*imu;
+	/* stores selected buf, valid IFF REQ_F_BUFFER_SELECTED is set */
+	struct io_buffer		*kbuf;
+	atomic_t			poll_refs;
+};
+
+struct io_tctx_node {
+	struct list_head	ctx_node;
+	struct task_struct	*task;
+	struct io_ring_ctx	*ctx;
+};
+
+struct io_defer_entry {
+	struct list_head	list;
+	struct io_kiocb		*req;
+	u32			seq;
+};
+
+struct io_op_def {
+	/* needs req->file assigned */
+	unsigned		needs_file : 1;
+	/* hash wq insertion if file is a regular file */
+	unsigned		hash_reg_file : 1;
+	/* unbound wq insertion if file is a non-regular file */
+	unsigned		unbound_nonreg_file : 1;
+	/* opcode is not supported by this kernel */
+	unsigned		not_supported : 1;
+	/* set if opcode supports polled "wait" */
+	unsigned		pollin : 1;
+	unsigned		pollout : 1;
+	/* op supports buffer selection */
+	unsigned		buffer_select : 1;
+	/* do prep async if is going to be punted */
+	unsigned		needs_async_setup : 1;
+	/* should block plug */
+	unsigned		plug : 1;
+	/* size of async data needed, if any */
+	unsigned short		async_size;
+};
+
+static const struct io_op_def io_op_defs[] = {
+	[IORING_OP_NOP] = {},
+	[IORING_OP_READV] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollin			= 1,
+		.buffer_select		= 1,
+		.needs_async_setup	= 1,
+		.plug			= 1,
+		.async_size		= sizeof(struct io_async_rw),
+	},
+	[IORING_OP_WRITEV] = {
+		.needs_file		= 1,
+		.hash_reg_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollout		= 1,
+		.needs_async_setup	= 1,
+		.plug			= 1,
+		.async_size		= sizeof(struct io_async_rw),
+	},
+	[IORING_OP_FSYNC] = {
+		.needs_file		= 1,
+	},
+	[IORING_OP_READ_FIXED] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollin			= 1,
+		.plug			= 1,
+		.async_size		= sizeof(struct io_async_rw),
+	},
+	[IORING_OP_WRITE_FIXED] = {
+		.needs_file		= 1,
+		.hash_reg_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollout		= 1,
+		.plug			= 1,
+		.async_size		= sizeof(struct io_async_rw),
+	},
+	[IORING_OP_POLL_ADD] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+	},
+	[IORING_OP_POLL_REMOVE] = {},
+	[IORING_OP_SYNC_FILE_RANGE] = {
+		.needs_file		= 1,
+	},
+	[IORING_OP_SENDMSG] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollout		= 1,
+		.needs_async_setup	= 1,
+		.async_size		= sizeof(struct io_async_msghdr),
+	},
+	[IORING_OP_RECVMSG] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollin			= 1,
+		.buffer_select		= 1,
+		.needs_async_setup	= 1,
+		.async_size		= sizeof(struct io_async_msghdr),
+	},
+	[IORING_OP_TIMEOUT] = {
+		.async_size		= sizeof(struct io_timeout_data),
+	},
+	[IORING_OP_TIMEOUT_REMOVE] = {
+		/* used by timeout updates' prep() */
+	},
+	[IORING_OP_ACCEPT] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollin			= 1,
+	},
+	[IORING_OP_ASYNC_CANCEL] = {},
+	[IORING_OP_LINK_TIMEOUT] = {
+		.async_size		= sizeof(struct io_timeout_data),
+	},
+	[IORING_OP_CONNECT] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollout		= 1,
+		.needs_async_setup	= 1,
+		.async_size		= sizeof(struct io_async_connect),
+	},
+	[IORING_OP_FALLOCATE] = {
+		.needs_file		= 1,
+	},
+	[IORING_OP_OPENAT] = {},
+	[IORING_OP_CLOSE] = {},
+	[IORING_OP_FILES_UPDATE] = {},
+	[IORING_OP_STATX] = {},
+	[IORING_OP_READ] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollin			= 1,
+		.buffer_select		= 1,
+		.plug			= 1,
+		.async_size		= sizeof(struct io_async_rw),
+	},
+	[IORING_OP_WRITE] = {
+		.needs_file		= 1,
+		.hash_reg_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollout		= 1,
+		.plug			= 1,
+		.async_size		= sizeof(struct io_async_rw),
+	},
+	[IORING_OP_FADVISE] = {
+		.needs_file		= 1,
+	},
+	[IORING_OP_MADVISE] = {},
+	[IORING_OP_SEND] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollout		= 1,
+	},
+	[IORING_OP_RECV] = {
+		.needs_file		= 1,
+		.unbound_nonreg_file	= 1,
+		.pollin			= 1,
+		.buffer_select		= 1,
+	},
+	[IORING_OP_OPENAT2] = {
+	},
+	[IORING_OP_EPOLL_CTL] = {
+		.unbound_nonreg_file	= 1,
+	},
+	[IORING_OP_SPLICE] = {
+		.needs_file		= 1,
+		.hash_reg_file		= 1,
+		.unbound_nonreg_file	= 1,
+	},
+	[IORING_OP_PROVIDE_BUFFERS] = {},
+	[IORING_OP_REMOVE_BUFFERS] = {},
+	[IORING_OP_TEE] = {
+		.needs_file		= 1,
+		.hash_reg_file		= 1,
+		.unbound_nonreg_file	= 1,
+	},
+	[IORING_OP_SHUTDOWN] = {
+		.needs_file		= 1,
+	},
+	[IORING_OP_RENAMEAT] = {},
+	[IORING_OP_UNLINKAT] = {},
+	[IORING_OP_MKDIRAT] = {},
+	[IORING_OP_SYMLINKAT] = {},
+	[IORING_OP_LINKAT] = {},
+};
+
+/* requests with any of those set should undergo io_disarm_next() */
+#define IO_DISARM_MASK (REQ_F_ARM_LTIMEOUT | REQ_F_LINK_TIMEOUT | REQ_F_FAIL)
+
+static bool io_disarm_next(struct io_kiocb *req);
+static void io_uring_del_tctx_node(unsigned long index);
+static void io_uring_try_cancel_requests(struct io_ring_ctx *ctx,
+					 struct task_struct *task,
+					 bool cancel_all);
+static void io_uring_cancel_generic(bool cancel_all, struct io_sq_data *sqd);
+
+static void io_fill_cqe_req(struct io_kiocb *req, s32 res, u32 cflags);
+
+static void io_put_req(struct io_kiocb *req);
+static void io_put_req_deferred(struct io_kiocb *req);
+static void io_dismantle_req(struct io_kiocb *req);
+static void io_queue_linked_timeout(struct io_kiocb *req);
+static int __io_register_rsrc_update(struct io_ring_ctx *ctx, unsigned type,
+				     struct io_uring_rsrc_update2 *up,
+				     unsigned nr_args);
+static void io_clean_op(struct io_kiocb *req);
+static struct file *io_file_get(struct io_ring_ctx *ctx,
+				struct io_kiocb *req, int fd, bool fixed,
+				unsigned int issue_flags);
+static void __io_queue_sqe(struct io_kiocb *req);
+static void io_rsrc_put_work(struct work_struct *work);
+
+static void io_req_task_queue(struct io_kiocb *req);
+static void io_submit_flush_completions(struct io_ring_ctx *ctx);
+static int io_req_prep_async(struct io_kiocb *req);
+
+static int io_install_fixed_file(struct io_kiocb *req, struct file *file,
+				 unsigned int issue_flags, u32 slot_index);
+static int io_close_fixed(struct io_kiocb *req, unsigned int issue_flags);
+
+static enum hrtimer_restart io_link_timeout_fn(struct hrtimer *timer);
+
+static struct kmem_cache *req_cachep;
+
+static const struct file_operations io_uring_fops;
+
+static int __read_mostly sysctl_io_uring_disabled;
+static int __read_mostly sysctl_io_uring_group = -1;
+
+#ifdef CONFIG_SYSCTL
+static struct ctl_table kernel_io_uring_disabled_table[] = {
+	{
+		.procname	= "io_uring_disabled",
+		.data		= &sysctl_io_uring_disabled,
+		.maxlen		= sizeof(sysctl_io_uring_disabled),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_TWO,
+	},
+	{
+		.procname	= "io_uring_group",
+		.data		= &sysctl_io_uring_group,
+		.maxlen		= sizeof(gid_t),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec,
+	},
+	{},
+};
+#endif
+
+static inline void io_tw_lock(struct io_ring_ctx *ctx, bool *locked)
+{
+	if (!*locked) {
+		mutex_lock(&ctx->uring_lock);
+		*locked = true;
+	}
+}
+
+#define io_for_each_link(pos, head) \
+	for (pos = (head); pos; pos = pos->link)
+
+/*
+ * Shamelessly stolen from the mm implementation of page reference checking,
+ * see commit f958d7b528b1 for details.
+ */
+#define req_ref_zero_or_close_to_overflow(req)	\
+	((unsigned int) atomic_read(&(req->refs)) + 127u <= 127u)
+
+static inline bool req_ref_inc_not_zero(struct io_kiocb *req)
+{
+	WARN_ON_ONCE(!(req->flags & REQ_F_REFCOUNT));
+	return atomic_inc_not_zero(&req->refs);
+}
+
+static inline bool req_ref_put_and_test(struct io_kiocb *req)
+{
+	if (likely(!(req->flags & REQ_F_REFCOUNT)))
+		return true;
+
+	WARN_ON_ONCE(req_ref_zero_or_close_to_overflow(req));
+	return atomic_dec_and_test(&req->refs);
+}
+
+static inline void req_ref_get(struct io_kiocb *req)
+{
+	WARN_ON_ONCE(!(req->flags & REQ_F_REFCOUNT));
+	WARN_ON_ONCE(req_ref_zero_or_close_to_overflow(req));
+	atomic_inc(&req->refs);
+}
+
+static inline void __io_req_set_refcount(struct io_kiocb *req, int nr)
+{
+	if (!(req->flags & REQ_F_REFCOUNT)) {
+		req->flags |= REQ_F_REFCOUNT;
+		atomic_set(&req->refs, nr);
+	}
+}
+
+static inline void io_req_set_refcount(struct io_kiocb *req)
+{
+	__io_req_set_refcount(req, 1);
+}
+
+static inline void io_req_set_rsrc_node(struct io_kiocb *req)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	if (!req->fixed_rsrc_refs) {
+		req->fixed_rsrc_refs = &ctx->rsrc_node->refs;
+		percpu_ref_get(req->fixed_rsrc_refs);
+	}
+}
+
+static void io_refs_resurrect(struct percpu_ref *ref, struct completion *compl)
+{
+	bool got = percpu_ref_tryget(ref);
+
+	/* already at zero, wait for ->release() */
+	if (!got)
+		wait_for_completion(compl);
+	percpu_ref_resurrect(ref);
+	if (got)
+		percpu_ref_put(ref);
+}
+
+static bool io_match_task(struct io_kiocb *head, struct task_struct *task,
+			  bool cancel_all)
+	__must_hold(&req->ctx->timeout_lock)
+{
+	struct io_kiocb *req;
+
+	if (task && head->task != task)
+		return false;
+	if (cancel_all)
+		return true;
+
+	io_for_each_link(req, head) {
+		if (req->flags & REQ_F_INFLIGHT)
+			return true;
+	}
+	return false;
+}
+
+static bool io_match_linked(struct io_kiocb *head)
+{
+	struct io_kiocb *req;
+
+	io_for_each_link(req, head) {
+		if (req->flags & REQ_F_INFLIGHT)
+			return true;
+	}
+	return false;
+}
+
+/*
+ * As io_match_task() but protected against racing with linked timeouts.
+ * User must not hold timeout_lock.
+ */
+static bool io_match_task_safe(struct io_kiocb *head, struct task_struct *task,
+			       bool cancel_all)
+{
+	bool matched;
+
+	if (task && head->task != task)
+		return false;
+	if (cancel_all)
+		return true;
+
+	if (head->flags & REQ_F_LINK_TIMEOUT) {
+		struct io_ring_ctx *ctx = head->ctx;
+
+		/* protect against races with linked timeouts */
+		spin_lock_irq(&ctx->timeout_lock);
+		matched = io_match_linked(head);
+		spin_unlock_irq(&ctx->timeout_lock);
+	} else {
+		matched = io_match_linked(head);
+	}
+	return matched;
+}
+
+static inline void req_set_fail(struct io_kiocb *req)
+{
+	req->flags |= REQ_F_FAIL;
+}
+
+static inline void req_fail_link_node(struct io_kiocb *req, int res)
+{
+	req_set_fail(req);
+	req->result = res;
+}
+
+static void io_ring_ctx_ref_free(struct percpu_ref *ref)
+{
+	struct io_ring_ctx *ctx = container_of(ref, struct io_ring_ctx, refs);
+
+	complete(&ctx->ref_comp);
+}
+
+static inline bool io_is_timeout_noseq(struct io_kiocb *req)
+{
+	return !req->timeout.off;
+}
+
+static void io_fallback_req_func(struct work_struct *work)
+{
+	struct io_ring_ctx *ctx = container_of(work, struct io_ring_ctx,
+						fallback_work.work);
+	struct llist_node *node = llist_del_all(&ctx->fallback_llist);
+	struct io_kiocb *req, *tmp;
+	bool locked = false;
+
+	percpu_ref_get(&ctx->refs);
+	llist_for_each_entry_safe(req, tmp, node, io_task_work.fallback_node)
+		req->io_task_work.func(req, &locked);
+
+	if (locked) {
+		if (ctx->submit_state.compl_nr)
+			io_submit_flush_completions(ctx);
+		mutex_unlock(&ctx->uring_lock);
+	}
+	percpu_ref_put(&ctx->refs);
+
+}
+
+static struct io_ring_ctx *io_ring_ctx_alloc(struct io_uring_params *p)
+{
+	struct io_ring_ctx *ctx;
+	int hash_bits;
+
+	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return NULL;
+
+	/*
+	 * Use 5 bits less than the max cq entries, that should give us around
+	 * 32 entries per hash list if totally full and uniformly spread.
+	 */
+	hash_bits = ilog2(p->cq_entries);
+	hash_bits -= 5;
+	if (hash_bits <= 0)
+		hash_bits = 1;
+	ctx->cancel_hash_bits = hash_bits;
+	ctx->cancel_hash = kmalloc((1U << hash_bits) * sizeof(struct hlist_head),
+					GFP_KERNEL);
+	if (!ctx->cancel_hash)
+		goto err;
+	__hash_init(ctx->cancel_hash, 1U << hash_bits);
+
+	ctx->dummy_ubuf = kzalloc(sizeof(*ctx->dummy_ubuf), GFP_KERNEL);
+	if (!ctx->dummy_ubuf)
+		goto err;
+	/* set invalid range, so io_import_fixed() fails meeting it */
+	ctx->dummy_ubuf->ubuf = -1UL;
+
+	if (percpu_ref_init(&ctx->refs, io_ring_ctx_ref_free,
+			    PERCPU_REF_ALLOW_REINIT, GFP_KERNEL))
+		goto err;
+
+	ctx->flags = p->flags;
+	init_waitqueue_head(&ctx->sqo_sq_wait);
+	INIT_LIST_HEAD(&ctx->sqd_list);
+	init_waitqueue_head(&ctx->poll_wait);
+	INIT_LIST_HEAD(&ctx->cq_overflow_list);
+	init_completion(&ctx->ref_comp);
+	xa_init_flags(&ctx->io_buffers, XA_FLAGS_ALLOC1);
+	xa_init_flags(&ctx->personalities, XA_FLAGS_ALLOC1);
+	mutex_init(&ctx->uring_lock);
+	init_waitqueue_head(&ctx->cq_wait);
+	spin_lock_init(&ctx->completion_lock);
+	spin_lock_init(&ctx->timeout_lock);
+	INIT_LIST_HEAD(&ctx->iopoll_list);
+	INIT_LIST_HEAD(&ctx->defer_list);
+	INIT_LIST_HEAD(&ctx->timeout_list);
+	INIT_LIST_HEAD(&ctx->ltimeout_list);
+	spin_lock_init(&ctx->rsrc_ref_lock);
+	INIT_LIST_HEAD(&ctx->rsrc_ref_list);
+	INIT_DELAYED_WORK(&ctx->rsrc_put_work, io_rsrc_put_work);
+	init_llist_head(&ctx->rsrc_put_llist);
+	INIT_LIST_HEAD(&ctx->tctx_list);
+	INIT_LIST_HEAD(&ctx->submit_state.free_list);
+	INIT_LIST_HEAD(&ctx->locked_free_list);
+	INIT_DELAYED_WORK(&ctx->fallback_work, io_fallback_req_func);
+	return ctx;
+err:
+	kfree(ctx->dummy_ubuf);
+	kfree(ctx->cancel_hash);
+	kfree(ctx);
+	return NULL;
+}
+
+static void io_account_cq_overflow(struct io_ring_ctx *ctx)
+{
+	struct io_rings *r = ctx->rings;
+
+	WRITE_ONCE(r->cq_overflow, READ_ONCE(r->cq_overflow) + 1);
+	ctx->cq_extra--;
+}
+
+static bool req_need_defer(struct io_kiocb *req, u32 seq)
+{
+	if (unlikely(req->flags & REQ_F_IO_DRAIN)) {
+		struct io_ring_ctx *ctx = req->ctx;
+
+		return seq + READ_ONCE(ctx->cq_extra) != ctx->cached_cq_tail;
+	}
+
+	return false;
+}
+
+#define FFS_ASYNC_READ		0x1UL
+#define FFS_ASYNC_WRITE		0x2UL
+#ifdef CONFIG_64BIT
+#define FFS_ISREG		0x4UL
+#else
+#define FFS_ISREG		0x0UL
+#endif
+#define FFS_MASK		~(FFS_ASYNC_READ|FFS_ASYNC_WRITE|FFS_ISREG)
+
+static inline bool io_req_ffs_set(struct io_kiocb *req)
+{
+	return IS_ENABLED(CONFIG_64BIT) && (req->flags & REQ_F_FIXED_FILE);
+}
+
+static void io_req_track_inflight(struct io_kiocb *req)
+{
+	if (!(req->flags & REQ_F_INFLIGHT)) {
+		req->flags |= REQ_F_INFLIGHT;
+		atomic_inc(&req->task->io_uring->inflight_tracked);
+	}
+}
+
+static struct io_kiocb *__io_prep_linked_timeout(struct io_kiocb *req)
+{
+	if (WARN_ON_ONCE(!req->link))
+		return NULL;
+
+	req->flags &= ~REQ_F_ARM_LTIMEOUT;
+	req->flags |= REQ_F_LINK_TIMEOUT;
+
+	/* linked timeouts should have two refs once prep'ed */
+	io_req_set_refcount(req);
+	__io_req_set_refcount(req->link, 2);
+	return req->link;
+}
+
+static inline struct io_kiocb *io_prep_linked_timeout(struct io_kiocb *req)
+{
+	if (likely(!(req->flags & REQ_F_ARM_LTIMEOUT)))
+		return NULL;
+	return __io_prep_linked_timeout(req);
+}
+
+static void io_prep_async_work(struct io_kiocb *req)
+{
+	const struct io_op_def *def = &io_op_defs[req->opcode];
+	struct io_ring_ctx *ctx = req->ctx;
+
+	if (!(req->flags & REQ_F_CREDS)) {
+		req->flags |= REQ_F_CREDS;
+		req->creds = get_current_cred();
+	}
+
+	req->work.list.next = NULL;
+	req->work.flags = 0;
+	if (req->flags & REQ_F_FORCE_ASYNC)
+		req->work.flags |= IO_WQ_WORK_CONCURRENT;
+
+	if (req->flags & REQ_F_ISREG) {
+		if (def->hash_reg_file || (ctx->flags & IORING_SETUP_IOPOLL))
+			io_wq_hash_work(&req->work, file_inode(req->file));
+	} else if (!req->file || !S_ISBLK(file_inode(req->file)->i_mode)) {
+		if (def->unbound_nonreg_file)
+			req->work.flags |= IO_WQ_WORK_UNBOUND;
+	}
+}
+
+static void io_prep_async_link(struct io_kiocb *req)
+{
+	struct io_kiocb *cur;
+
+	if (req->flags & REQ_F_LINK_TIMEOUT) {
+		struct io_ring_ctx *ctx = req->ctx;
+
+		spin_lock_irq(&ctx->timeout_lock);
+		io_for_each_link(cur, req)
+			io_prep_async_work(cur);
+		spin_unlock_irq(&ctx->timeout_lock);
+	} else {
+		io_for_each_link(cur, req)
+			io_prep_async_work(cur);
+	}
+}
+
+static void io_queue_async_work(struct io_kiocb *req, bool *locked)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_kiocb *link = io_prep_linked_timeout(req);
+	struct io_uring_task *tctx = req->task->io_uring;
+
+	/* must not take the lock, NULL it as a precaution */
+	locked = NULL;
+
+	BUG_ON(!tctx);
+	BUG_ON(!tctx->io_wq);
+
+	/* init ->work of the whole link before punting */
+	io_prep_async_link(req);
+
+	/*
+	 * Not expected to happen, but if we do have a bug where this _can_
+	 * happen, catch it here and ensure the request is marked as
+	 * canceled. That will make io-wq go through the usual work cancel
+	 * procedure rather than attempt to run this request (or create a new
+	 * worker for it).
+	 */
+	if (WARN_ON_ONCE(!same_thread_group(req->task, current)))
+		req->work.flags |= IO_WQ_WORK_CANCEL;
+
+	trace_io_uring_queue_async_work(ctx, io_wq_is_hashed(&req->work), req,
+					&req->work, req->flags);
+	io_wq_enqueue(tctx->io_wq, &req->work);
+	if (link)
+		io_queue_linked_timeout(link);
+}
+
+static void io_kill_timeout(struct io_kiocb *req, int status)
+	__must_hold(&req->ctx->completion_lock)
+	__must_hold(&req->ctx->timeout_lock)
+{
+	struct io_timeout_data *io = req->async_data;
+
+	if (hrtimer_try_to_cancel(&io->timer) != -1) {
+		if (status)
+			req_set_fail(req);
+		atomic_set(&req->ctx->cq_timeouts,
+			atomic_read(&req->ctx->cq_timeouts) + 1);
+		list_del_init(&req->timeout.list);
+		io_fill_cqe_req(req, status, 0);
+		io_put_req_deferred(req);
+	}
+}
+
+static void io_queue_deferred(struct io_ring_ctx *ctx)
+{
+	lockdep_assert_held(&ctx->completion_lock);
+
+	while (!list_empty(&ctx->defer_list)) {
+		struct io_defer_entry *de = list_first_entry(&ctx->defer_list,
+						struct io_defer_entry, list);
+
+		if (req_need_defer(de->req, de->seq))
+			break;
+		list_del_init(&de->list);
+		io_req_task_queue(de->req);
+		kfree(de);
+	}
+}
+
+static void io_flush_timeouts(struct io_ring_ctx *ctx)
+	__must_hold(&ctx->completion_lock)
+{
+	u32 seq = ctx->cached_cq_tail - atomic_read(&ctx->cq_timeouts);
+	struct io_kiocb *req, *tmp;
+
+	spin_lock_irq(&ctx->timeout_lock);
+	list_for_each_entry_safe(req, tmp, &ctx->timeout_list, timeout.list) {
+		u32 events_needed, events_got;
+
+		if (io_is_timeout_noseq(req))
+			break;
+
+		/*
+		 * Since seq can easily wrap around over time, subtract
+		 * the last seq at which timeouts were flushed before comparing.
+		 * Assuming not more than 2^31-1 events have happened since,
+		 * these subtractions won't have wrapped, so we can check if
+		 * target is in [last_seq, current_seq] by comparing the two.
+		 */
+		events_needed = req->timeout.target_seq - ctx->cq_last_tm_flush;
+		events_got = seq - ctx->cq_last_tm_flush;
+		if (events_got < events_needed)
+			break;
+
+		io_kill_timeout(req, 0);
+	}
+	ctx->cq_last_tm_flush = seq;
+	spin_unlock_irq(&ctx->timeout_lock);
+}
+
+static void __io_commit_cqring_flush(struct io_ring_ctx *ctx)
+{
+	if (ctx->off_timeout_used)
+		io_flush_timeouts(ctx);
+	if (ctx->drain_active)
+		io_queue_deferred(ctx);
+}
+
+static inline bool io_commit_needs_flush(struct io_ring_ctx *ctx)
+{
+	return ctx->off_timeout_used || ctx->drain_active;
+}
+
+static inline void __io_commit_cqring(struct io_ring_ctx *ctx)
+{
+	/* order cqe stores with ring update */
+	smp_store_release(&ctx->rings->cq.tail, ctx->cached_cq_tail);
+}
+
+static inline void io_commit_cqring(struct io_ring_ctx *ctx)
+{
+	if (unlikely(io_commit_needs_flush(ctx)))
+		__io_commit_cqring_flush(ctx);
+	__io_commit_cqring(ctx);
+}
+
+static inline bool io_sqring_full(struct io_ring_ctx *ctx)
+{
+	struct io_rings *r = ctx->rings;
+
+	/*
+	 * SQPOLL must use the actual sqring head, as using the cached_sq_head
+	 * is race prone if the SQPOLL thread has grabbed entries but not yet
+	 * committed them to the ring. For !SQPOLL, this doesn't matter, but
+	 * since this helper is just used for SQPOLL sqring waits (or POLLOUT),
+	 * just read the actual sqring head unconditionally.
+	 */
+	return READ_ONCE(r->sq.tail) - READ_ONCE(r->sq.head) == ctx->sq_entries;
+}
+
+static inline unsigned int __io_cqring_events(struct io_ring_ctx *ctx)
+{
+	return ctx->cached_cq_tail - READ_ONCE(ctx->rings->cq.head);
+}
+
+static inline struct io_uring_cqe *io_get_cqe(struct io_ring_ctx *ctx)
+{
+	struct io_rings *rings = ctx->rings;
+	unsigned tail, mask = ctx->cq_entries - 1;
+
+	/*
+	 * writes to the cq entry need to come after reading head; the
+	 * control dependency is enough as we're using WRITE_ONCE to
+	 * fill the cq entry
+	 */
+	if (__io_cqring_events(ctx) == ctx->cq_entries)
+		return NULL;
+
+	tail = ctx->cached_cq_tail++;
+	return &rings->cqes[tail & mask];
+}
+
+static inline bool io_should_trigger_evfd(struct io_ring_ctx *ctx)
+{
+	if (likely(!ctx->cq_ev_fd))
+		return false;
+	if (READ_ONCE(ctx->rings->cq_flags) & IORING_CQ_EVENTFD_DISABLED)
+		return false;
+	return !ctx->eventfd_async || io_wq_current_is_worker();
+}
+
+/*
+ * This should only get called when at least one event has been posted.
+ * Some applications rely on the eventfd notification count only changing
+ * IFF a new CQE has been added to the CQ ring. There's no depedency on
+ * 1:1 relationship between how many times this function is called (and
+ * hence the eventfd count) and number of CQEs posted to the CQ ring.
+ */
+static void io_cqring_ev_posted(struct io_ring_ctx *ctx)
+{
+	/*
+	 * wake_up_all() may seem excessive, but io_wake_function() and
+	 * io_should_wake() handle the termination of the loop and only
+	 * wake as many waiters as we need to.
+	 */
+	if (wq_has_sleeper(&ctx->cq_wait))
+		__wake_up(&ctx->cq_wait, TASK_NORMAL, 0,
+				poll_to_key(EPOLL_URING_WAKE | EPOLLIN));
+	if (ctx->sq_data && waitqueue_active(&ctx->sq_data->wait))
+		wake_up(&ctx->sq_data->wait);
+	if (io_should_trigger_evfd(ctx))
+		eventfd_signal_mask(ctx->cq_ev_fd, 1, EPOLL_URING_WAKE);
+	if (waitqueue_active(&ctx->poll_wait))
+		__wake_up(&ctx->poll_wait, TASK_INTERRUPTIBLE, 0,
+				poll_to_key(EPOLL_URING_WAKE | EPOLLIN));
+}
+
+static void io_cqring_ev_posted_iopoll(struct io_ring_ctx *ctx)
+{
+	/* see waitqueue_active() comment */
+	smp_mb();
+
+	if (ctx->flags & IORING_SETUP_SQPOLL) {
+		if (waitqueue_active(&ctx->cq_wait))
+			__wake_up(&ctx->cq_wait, TASK_NORMAL, 0,
+				  poll_to_key(EPOLL_URING_WAKE | EPOLLIN));
+	}
+	if (io_should_trigger_evfd(ctx))
+		eventfd_signal_mask(ctx->cq_ev_fd, 1, EPOLL_URING_WAKE);
+	if (waitqueue_active(&ctx->poll_wait))
+		__wake_up(&ctx->poll_wait, TASK_INTERRUPTIBLE, 0,
+				poll_to_key(EPOLL_URING_WAKE | EPOLLIN));
+}
+
+/* Returns true if there are no backlogged entries after the flush */
+static bool __io_cqring_overflow_flush(struct io_ring_ctx *ctx, bool force)
+{
+	bool all_flushed, posted;
+
+	if (!force && __io_cqring_events(ctx) == ctx->cq_entries)
+		return false;
+
+	posted = false;
+	spin_lock(&ctx->completion_lock);
+	while (!list_empty(&ctx->cq_overflow_list)) {
+		struct io_uring_cqe *cqe = io_get_cqe(ctx);
+		struct io_overflow_cqe *ocqe;
+
+		if (!cqe && !force)
+			break;
+		ocqe = list_first_entry(&ctx->cq_overflow_list,
+					struct io_overflow_cqe, list);
+		if (cqe)
+			memcpy(cqe, &ocqe->cqe, sizeof(*cqe));
+		else
+			io_account_cq_overflow(ctx);
+
+		posted = true;
+		list_del(&ocqe->list);
+		kfree(ocqe);
+	}
+
+	all_flushed = list_empty(&ctx->cq_overflow_list);
+	if (all_flushed) {
+		clear_bit(0, &ctx->check_cq_overflow);
+		WRITE_ONCE(ctx->rings->sq_flags,
+			   ctx->rings->sq_flags & ~IORING_SQ_CQ_OVERFLOW);
+	}
+
+	if (posted)
+		io_commit_cqring(ctx);
+	spin_unlock(&ctx->completion_lock);
+	if (posted)
+		io_cqring_ev_posted(ctx);
+	return all_flushed;
+}
+
+static bool io_cqring_overflow_flush(struct io_ring_ctx *ctx)
+{
+	bool ret = true;
+
+	if (test_bit(0, &ctx->check_cq_overflow)) {
+		/* iopoll syncs against uring_lock, not completion_lock */
+		if (ctx->flags & IORING_SETUP_IOPOLL)
+			mutex_lock(&ctx->uring_lock);
+		ret = __io_cqring_overflow_flush(ctx, false);
+		if (ctx->flags & IORING_SETUP_IOPOLL)
+			mutex_unlock(&ctx->uring_lock);
+	}
+
+	return ret;
+}
+
+/* must to be called somewhat shortly after putting a request */
+static inline void io_put_task(struct task_struct *task, int nr)
+{
+	struct io_uring_task *tctx = task->io_uring;
+
+	if (likely(task == current)) {
+		tctx->cached_refs += nr;
+	} else {
+		percpu_counter_sub(&tctx->inflight, nr);
+		if (unlikely(atomic_read(&tctx->in_idle)))
+			wake_up(&tctx->wait);
+		put_task_struct_many(task, nr);
+	}
+}
+
+static void io_task_refs_refill(struct io_uring_task *tctx)
+{
+	unsigned int refill = -tctx->cached_refs + IO_TCTX_REFS_CACHE_NR;
+
+	percpu_counter_add(&tctx->inflight, refill);
+	refcount_add(refill, &current->usage);
+	tctx->cached_refs += refill;
+}
+
+static inline void io_get_task_refs(int nr)
+{
+	struct io_uring_task *tctx = current->io_uring;
+
+	tctx->cached_refs -= nr;
+	if (unlikely(tctx->cached_refs < 0))
+		io_task_refs_refill(tctx);
+}
+
+static __cold void io_uring_drop_tctx_refs(struct task_struct *task)
+{
+	struct io_uring_task *tctx = task->io_uring;
+	unsigned int refs = tctx->cached_refs;
+
+	if (refs) {
+		tctx->cached_refs = 0;
+		percpu_counter_sub(&tctx->inflight, refs);
+		put_task_struct_many(task, refs);
+	}
+}
+
+static bool io_cqring_event_overflow(struct io_ring_ctx *ctx, u64 user_data,
+				     s32 res, u32 cflags)
+{
+	struct io_overflow_cqe *ocqe;
+
+	ocqe = kmalloc(sizeof(*ocqe), GFP_ATOMIC | __GFP_ACCOUNT);
+	if (!ocqe) {
+		/*
+		 * If we're in ring overflow flush mode, or in task cancel mode,
+		 * or cannot allocate an overflow entry, then we need to drop it
+		 * on the floor.
+		 */
+		io_account_cq_overflow(ctx);
+		return false;
+	}
+	if (list_empty(&ctx->cq_overflow_list)) {
+		set_bit(0, &ctx->check_cq_overflow);
+		WRITE_ONCE(ctx->rings->sq_flags,
+			   ctx->rings->sq_flags | IORING_SQ_CQ_OVERFLOW);
+
+	}
+	ocqe->cqe.user_data = user_data;
+	ocqe->cqe.res = res;
+	ocqe->cqe.flags = cflags;
+	list_add_tail(&ocqe->list, &ctx->cq_overflow_list);
+	return true;
+}
+
+static inline bool __io_fill_cqe(struct io_ring_ctx *ctx, u64 user_data,
+				 s32 res, u32 cflags)
+{
+	struct io_uring_cqe *cqe;
+
+	trace_io_uring_complete(ctx, user_data, res, cflags);
+
+	/*
+	 * If we can't get a cq entry, userspace overflowed the
+	 * submission (by quite a lot). Increment the overflow count in
+	 * the ring.
+	 */
+	cqe = io_get_cqe(ctx);
+	if (likely(cqe)) {
+		WRITE_ONCE(cqe->user_data, user_data);
+		WRITE_ONCE(cqe->res, res);
+		WRITE_ONCE(cqe->flags, cflags);
+		return true;
+	}
+	return io_cqring_event_overflow(ctx, user_data, res, cflags);
+}
+
+static noinline void io_fill_cqe_req(struct io_kiocb *req, s32 res, u32 cflags)
+{
+	__io_fill_cqe(req->ctx, req->user_data, res, cflags);
+}
+
+static noinline bool io_fill_cqe_aux(struct io_ring_ctx *ctx, u64 user_data,
+				     s32 res, u32 cflags)
+{
+	ctx->cq_extra++;
+	return __io_fill_cqe(ctx, user_data, res, cflags);
+}
+
+static void io_req_complete_post(struct io_kiocb *req, s32 res,
+				 u32 cflags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	spin_lock(&ctx->completion_lock);
+	__io_fill_cqe(ctx, req->user_data, res, cflags);
+	/*
+	 * If we're the last reference to this request, add to our locked
+	 * free_list cache.
+	 */
+	if (req_ref_put_and_test(req)) {
+		if (req->flags & (REQ_F_LINK | REQ_F_HARDLINK)) {
+			if (req->flags & IO_DISARM_MASK)
+				io_disarm_next(req);
+			if (req->link) {
+				io_req_task_queue(req->link);
+				req->link = NULL;
+			}
+		}
+		io_dismantle_req(req);
+		io_put_task(req->task, 1);
+		list_add(&req->inflight_entry, &ctx->locked_free_list);
+		ctx->locked_free_nr++;
+	} else {
+		if (!percpu_ref_tryget(&ctx->refs))
+			req = NULL;
+	}
+	io_commit_cqring(ctx);
+	spin_unlock(&ctx->completion_lock);
+
+	if (req) {
+		io_cqring_ev_posted(ctx);
+		percpu_ref_put(&ctx->refs);
+	}
+}
+
+static inline bool io_req_needs_clean(struct io_kiocb *req)
+{
+	return req->flags & IO_REQ_CLEAN_FLAGS;
+}
+
+static inline void io_req_complete_state(struct io_kiocb *req, s32 res,
+					 u32 cflags)
+{
+	if (io_req_needs_clean(req))
+		io_clean_op(req);
+	req->result = res;
+	req->compl.cflags = cflags;
+	req->flags |= REQ_F_COMPLETE_INLINE;
+}
+
+static inline void __io_req_complete(struct io_kiocb *req, unsigned issue_flags,
+				     s32 res, u32 cflags)
+{
+	if (issue_flags & IO_URING_F_COMPLETE_DEFER)
+		io_req_complete_state(req, res, cflags);
+	else
+		io_req_complete_post(req, res, cflags);
+}
+
+static inline void io_req_complete(struct io_kiocb *req, s32 res)
+{
+	__io_req_complete(req, 0, res, 0);
+}
+
+static void io_req_complete_failed(struct io_kiocb *req, s32 res)
+{
+	req_set_fail(req);
+	io_req_complete_post(req, res, 0);
+}
+
+static void io_req_complete_fail_submit(struct io_kiocb *req)
+{
+	/*
+	 * We don't submit, fail them all, for that replace hardlinks with
+	 * normal links. Extra REQ_F_LINK is tolerated.
+	 */
+	req->flags &= ~REQ_F_HARDLINK;
+	req->flags |= REQ_F_LINK;
+	io_req_complete_failed(req, req->result);
+}
+
+/*
+ * Don't initialise the fields below on every allocation, but do that in
+ * advance and keep them valid across allocations.
+ */
+static void io_preinit_req(struct io_kiocb *req, struct io_ring_ctx *ctx)
+{
+	req->ctx = ctx;
+	req->link = NULL;
+	req->async_data = NULL;
+	/* not necessary, but safer to zero */
+	req->result = 0;
+}
+
+static void io_flush_cached_locked_reqs(struct io_ring_ctx *ctx,
+					struct io_submit_state *state)
+{
+	spin_lock(&ctx->completion_lock);
+	list_splice_init(&ctx->locked_free_list, &state->free_list);
+	ctx->locked_free_nr = 0;
+	spin_unlock(&ctx->completion_lock);
+}
+
+/* Returns true IFF there are requests in the cache */
+static bool io_flush_cached_reqs(struct io_ring_ctx *ctx)
+{
+	struct io_submit_state *state = &ctx->submit_state;
+	int nr;
+
+	/*
+	 * If we have more than a batch's worth of requests in our IRQ side
+	 * locked cache, grab the lock and move them over to our submission
+	 * side cache.
+	 */
+	if (READ_ONCE(ctx->locked_free_nr) > IO_COMPL_BATCH)
+		io_flush_cached_locked_reqs(ctx, state);
+
+	nr = state->free_reqs;
+	while (!list_empty(&state->free_list)) {
+		struct io_kiocb *req = list_first_entry(&state->free_list,
+					struct io_kiocb, inflight_entry);
+
+		list_del(&req->inflight_entry);
+		state->reqs[nr++] = req;
+		if (nr == ARRAY_SIZE(state->reqs))
+			break;
+	}
+
+	state->free_reqs = nr;
+	return nr != 0;
+}
+
+/*
+ * A request might get retired back into the request caches even before opcode
+ * handlers and io_issue_sqe() are done with it, e.g. inline completion path.
+ * Because of that, io_alloc_req() should be called only under ->uring_lock
+ * and with extra caution to not get a request that is still worked on.
+ */
+static struct io_kiocb *io_alloc_req(struct io_ring_ctx *ctx)
+	__must_hold(&ctx->uring_lock)
+{
+	struct io_submit_state *state = &ctx->submit_state;
+	gfp_t gfp = GFP_KERNEL | __GFP_NOWARN;
+	int ret, i;
+
+	BUILD_BUG_ON(ARRAY_SIZE(state->reqs) < IO_REQ_ALLOC_BATCH);
+
+	if (likely(state->free_reqs || io_flush_cached_reqs(ctx)))
+		goto got_req;
+
+	ret = kmem_cache_alloc_bulk(req_cachep, gfp, IO_REQ_ALLOC_BATCH,
+				    state->reqs);
+
+	/*
+	 * Bulk alloc is all-or-nothing. If we fail to get a batch,
+	 * retry single alloc to be on the safe side.
+	 */
+	if (unlikely(ret <= 0)) {
+		state->reqs[0] = kmem_cache_alloc(req_cachep, gfp);
+		if (!state->reqs[0])
+			return NULL;
+		ret = 1;
+	}
+
+	for (i = 0; i < ret; i++)
+		io_preinit_req(state->reqs[i], ctx);
+	state->free_reqs = ret;
+got_req:
+	state->free_reqs--;
+	return state->reqs[state->free_reqs];
+}
+
+static inline void io_put_file(struct file *file)
+{
+	if (file)
+		fput(file);
+}
+
+static void io_dismantle_req(struct io_kiocb *req)
+{
+	unsigned int flags = req->flags;
+
+	if (io_req_needs_clean(req))
+		io_clean_op(req);
+	if (!(flags & REQ_F_FIXED_FILE))
+		io_put_file(req->file);
+	if (req->fixed_rsrc_refs)
+		percpu_ref_put(req->fixed_rsrc_refs);
+	if (req->async_data) {
+		kfree(req->async_data);
+		req->async_data = NULL;
+	}
+}
+
+static void __io_free_req(struct io_kiocb *req)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	io_dismantle_req(req);
+	io_put_task(req->task, 1);
+
+	spin_lock(&ctx->completion_lock);
+	list_add(&req->inflight_entry, &ctx->locked_free_list);
+	ctx->locked_free_nr++;
+	spin_unlock(&ctx->completion_lock);
+
+	percpu_ref_put(&ctx->refs);
+}
+
+static inline void io_remove_next_linked(struct io_kiocb *req)
+{
+	struct io_kiocb *nxt = req->link;
+
+	req->link = nxt->link;
+	nxt->link = NULL;
+}
+
+static bool io_kill_linked_timeout(struct io_kiocb *req)
+	__must_hold(&req->ctx->completion_lock)
+	__must_hold(&req->ctx->timeout_lock)
+{
+	struct io_kiocb *link = req->link;
+
+	if (link && link->opcode == IORING_OP_LINK_TIMEOUT) {
+		struct io_timeout_data *io = link->async_data;
+
+		io_remove_next_linked(req);
+		link->timeout.head = NULL;
+		if (hrtimer_try_to_cancel(&io->timer) != -1) {
+			list_del(&link->timeout.list);
+			io_fill_cqe_req(link, -ECANCELED, 0);
+			io_put_req_deferred(link);
+			return true;
+		}
+	}
+	return false;
+}
+
+static void io_fail_links(struct io_kiocb *req)
+	__must_hold(&req->ctx->completion_lock)
+{
+	struct io_kiocb *nxt, *link = req->link;
+
+	req->link = NULL;
+	while (link) {
+		long res = -ECANCELED;
+
+		if (link->flags & REQ_F_FAIL)
+			res = link->result;
+
+		nxt = link->link;
+		link->link = NULL;
+
+		trace_io_uring_fail_link(req, link);
+		io_fill_cqe_req(link, res, 0);
+		io_put_req_deferred(link);
+		link = nxt;
+	}
+}
+
+static bool io_disarm_next(struct io_kiocb *req)
+	__must_hold(&req->ctx->completion_lock)
+{
+	bool posted = false;
+
+	if (req->flags & REQ_F_ARM_LTIMEOUT) {
+		struct io_kiocb *link = req->link;
+
+		req->flags &= ~REQ_F_ARM_LTIMEOUT;
+		if (link && link->opcode == IORING_OP_LINK_TIMEOUT) {
+			io_remove_next_linked(req);
+			io_fill_cqe_req(link, -ECANCELED, 0);
+			io_put_req_deferred(link);
+			posted = true;
+		}
+	} else if (req->flags & REQ_F_LINK_TIMEOUT) {
+		struct io_ring_ctx *ctx = req->ctx;
+
+		spin_lock_irq(&ctx->timeout_lock);
+		posted = io_kill_linked_timeout(req);
+		spin_unlock_irq(&ctx->timeout_lock);
+	}
+	if (unlikely((req->flags & REQ_F_FAIL) &&
+		     !(req->flags & REQ_F_HARDLINK))) {
+		posted |= (req->link != NULL);
+		io_fail_links(req);
+	}
+	return posted;
+}
+
+static struct io_kiocb *__io_req_find_next(struct io_kiocb *req)
+{
+	struct io_kiocb *nxt;
+
+	/*
+	 * If LINK is set, we have dependent requests in this chain. If we
+	 * didn't fail this request, queue the first one up, moving any other
+	 * dependencies to the next request. In case of failure, fail the rest
+	 * of the chain.
+	 */
+	if (req->flags & IO_DISARM_MASK) {
+		struct io_ring_ctx *ctx = req->ctx;
+		bool posted;
+
+		spin_lock(&ctx->completion_lock);
+		posted = io_disarm_next(req);
+		if (posted)
+			io_commit_cqring(req->ctx);
+		spin_unlock(&ctx->completion_lock);
+		if (posted)
+			io_cqring_ev_posted(ctx);
+	}
+	nxt = req->link;
+	req->link = NULL;
+	return nxt;
+}
+
+static inline struct io_kiocb *io_req_find_next(struct io_kiocb *req)
+{
+	if (likely(!(req->flags & (REQ_F_LINK|REQ_F_HARDLINK))))
+		return NULL;
+	return __io_req_find_next(req);
+}
+
+static void ctx_flush_and_put(struct io_ring_ctx *ctx, bool *locked)
+{
+	if (!ctx)
+		return;
+	if (*locked) {
+		if (ctx->submit_state.compl_nr)
+			io_submit_flush_completions(ctx);
+		mutex_unlock(&ctx->uring_lock);
+		*locked = false;
+	}
+	percpu_ref_put(&ctx->refs);
+}
+
+static void tctx_task_work(struct callback_head *cb)
+{
+	bool locked = false;
+	struct io_ring_ctx *ctx = NULL;
+	struct io_uring_task *tctx = container_of(cb, struct io_uring_task,
+						  task_work);
+
+	while (1) {
+		struct io_wq_work_node *node;
+
+		if (!tctx->task_list.first && locked && ctx->submit_state.compl_nr)
+			io_submit_flush_completions(ctx);
+
+		spin_lock_irq(&tctx->task_lock);
+		node = tctx->task_list.first;
+		INIT_WQ_LIST(&tctx->task_list);
+		if (!node)
+			tctx->task_running = false;
+		spin_unlock_irq(&tctx->task_lock);
+		if (!node)
+			break;
+
+		do {
+			struct io_wq_work_node *next = node->next;
+			struct io_kiocb *req = container_of(node, struct io_kiocb,
+							    io_task_work.node);
+
+			if (req->ctx != ctx) {
+				ctx_flush_and_put(ctx, &locked);
+				ctx = req->ctx;
+				/* if not contended, grab and improve batching */
+				locked = mutex_trylock(&ctx->uring_lock);
+				percpu_ref_get(&ctx->refs);
+			}
+			req->io_task_work.func(req, &locked);
+			node = next;
+			if (unlikely(need_resched())) {
+				ctx_flush_and_put(ctx, &locked);
+				ctx = NULL;
+				cond_resched();
+			}
+		} while (node);
+	}
+
+	ctx_flush_and_put(ctx, &locked);
+
+	/* relaxed read is enough as only the task itself sets ->in_idle */
+	if (unlikely(atomic_read(&tctx->in_idle)))
+		io_uring_drop_tctx_refs(current);
+}
+
+static void io_req_task_work_add(struct io_kiocb *req)
+{
+	struct task_struct *tsk = req->task;
+	struct io_uring_task *tctx = tsk->io_uring;
+	enum task_work_notify_mode notify;
+	struct io_wq_work_node *node;
+	unsigned long flags;
+	bool running;
+
+	WARN_ON_ONCE(!tctx);
+
+	spin_lock_irqsave(&tctx->task_lock, flags);
+	wq_list_add_tail(&req->io_task_work.node, &tctx->task_list);
+	running = tctx->task_running;
+	if (!running)
+		tctx->task_running = true;
+	spin_unlock_irqrestore(&tctx->task_lock, flags);
+
+	/* task_work already pending, we're done */
+	if (running)
+		return;
+
+	/*
+	 * SQPOLL kernel thread doesn't need notification, just a wakeup. For
+	 * all other cases, use TWA_SIGNAL unconditionally to ensure we're
+	 * processing task_work. There's no reliable way to tell if TWA_RESUME
+	 * will do the job.
+	 */
+	notify = (req->ctx->flags & IORING_SETUP_SQPOLL) ? TWA_NONE : TWA_SIGNAL;
+	if (!task_work_add(tsk, &tctx->task_work, notify)) {
+		wake_up_process(tsk);
+		return;
+	}
+
+	spin_lock_irqsave(&tctx->task_lock, flags);
+	tctx->task_running = false;
+	node = tctx->task_list.first;
+	INIT_WQ_LIST(&tctx->task_list);
+	spin_unlock_irqrestore(&tctx->task_lock, flags);
+
+	while (node) {
+		req = container_of(node, struct io_kiocb, io_task_work.node);
+		node = node->next;
+		if (llist_add(&req->io_task_work.fallback_node,
+			      &req->ctx->fallback_llist))
+			schedule_delayed_work(&req->ctx->fallback_work, 1);
+	}
+}
+
+static void io_req_task_cancel(struct io_kiocb *req, bool *locked)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	/* not needed for normal modes, but SQPOLL depends on it */
+	io_tw_lock(ctx, locked);
+	io_req_complete_failed(req, req->result);
+}
+
+static void io_req_task_submit(struct io_kiocb *req, bool *locked)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	io_tw_lock(ctx, locked);
+	/* req->task == current here, checking PF_EXITING is safe */
+	if (likely(!(req->task->flags & PF_EXITING)))
+		__io_queue_sqe(req);
+	else
+		io_req_complete_failed(req, -EFAULT);
+}
+
+static void io_req_task_queue_fail(struct io_kiocb *req, int ret)
+{
+	req->result = ret;
+	req->io_task_work.func = io_req_task_cancel;
+	io_req_task_work_add(req);
+}
+
+static void io_req_task_queue(struct io_kiocb *req)
+{
+	req->io_task_work.func = io_req_task_submit;
+	io_req_task_work_add(req);
+}
+
+static void io_req_task_queue_reissue(struct io_kiocb *req)
+{
+	req->io_task_work.func = io_queue_async_work;
+	io_req_task_work_add(req);
+}
+
+static inline void io_queue_next(struct io_kiocb *req)
+{
+	struct io_kiocb *nxt = io_req_find_next(req);
+
+	if (nxt)
+		io_req_task_queue(nxt);
+}
+
+static void io_free_req(struct io_kiocb *req)
+{
+	io_queue_next(req);
+	__io_free_req(req);
+}
+
+static void io_free_req_work(struct io_kiocb *req, bool *locked)
+{
+	io_free_req(req);
+}
+
+struct req_batch {
+	struct task_struct	*task;
+	int			task_refs;
+	int			ctx_refs;
+};
+
+static inline void io_init_req_batch(struct req_batch *rb)
+{
+	rb->task_refs = 0;
+	rb->ctx_refs = 0;
+	rb->task = NULL;
+}
+
+static void io_req_free_batch_finish(struct io_ring_ctx *ctx,
+				     struct req_batch *rb)
+{
+	if (rb->ctx_refs)
+		percpu_ref_put_many(&ctx->refs, rb->ctx_refs);
+	if (rb->task)
+		io_put_task(rb->task, rb->task_refs);
+}
+
+static void io_req_free_batch(struct req_batch *rb, struct io_kiocb *req,
+			      struct io_submit_state *state)
+{
+	io_queue_next(req);
+	io_dismantle_req(req);
+
+	if (req->task != rb->task) {
+		if (rb->task)
+			io_put_task(rb->task, rb->task_refs);
+		rb->task = req->task;
+		rb->task_refs = 0;
+	}
+	rb->task_refs++;
+	rb->ctx_refs++;
+
+	if (state->free_reqs != ARRAY_SIZE(state->reqs))
+		state->reqs[state->free_reqs++] = req;
+	else
+		list_add(&req->inflight_entry, &state->free_list);
+}
+
+static void io_submit_flush_completions(struct io_ring_ctx *ctx)
+	__must_hold(&ctx->uring_lock)
+{
+	struct io_submit_state *state = &ctx->submit_state;
+	int i, nr = state->compl_nr;
+	struct req_batch rb;
+
+	spin_lock(&ctx->completion_lock);
+	for (i = 0; i < nr; i++) {
+		struct io_kiocb *req = state->compl_reqs[i];
+
+		__io_fill_cqe(ctx, req->user_data, req->result,
+			      req->compl.cflags);
+	}
+	io_commit_cqring(ctx);
+	spin_unlock(&ctx->completion_lock);
+	io_cqring_ev_posted(ctx);
+
+	io_init_req_batch(&rb);
+	for (i = 0; i < nr; i++) {
+		struct io_kiocb *req = state->compl_reqs[i];
+
+		if (req_ref_put_and_test(req))
+			io_req_free_batch(&rb, req, &ctx->submit_state);
+	}
+
+	io_req_free_batch_finish(ctx, &rb);
+	state->compl_nr = 0;
+}
+
+/*
+ * Drop reference to request, return next in chain (if there is one) if this
+ * was the last reference to this request.
+ */
+static inline struct io_kiocb *io_put_req_find_next(struct io_kiocb *req)
+{
+	struct io_kiocb *nxt = NULL;
+
+	if (req_ref_put_and_test(req)) {
+		nxt = io_req_find_next(req);
+		__io_free_req(req);
+	}
+	return nxt;
+}
+
+static inline void io_put_req(struct io_kiocb *req)
+{
+	if (req_ref_put_and_test(req))
+		io_free_req(req);
+}
+
+static inline void io_put_req_deferred(struct io_kiocb *req)
+{
+	if (req_ref_put_and_test(req)) {
+		req->io_task_work.func = io_free_req_work;
+		io_req_task_work_add(req);
+	}
+}
+
+static unsigned io_cqring_events(struct io_ring_ctx *ctx)
+{
+	/* See comment at the top of this file */
+	smp_rmb();
+	return __io_cqring_events(ctx);
+}
+
+static inline unsigned int io_sqring_entries(struct io_ring_ctx *ctx)
+{
+	struct io_rings *rings = ctx->rings;
+
+	/* make sure SQ entry isn't read before tail */
+	return smp_load_acquire(&rings->sq.tail) - ctx->cached_sq_head;
+}
+
+static unsigned int io_put_kbuf(struct io_kiocb *req, struct io_buffer *kbuf)
+{
+	unsigned int cflags;
+
+	cflags = kbuf->bid << IORING_CQE_BUFFER_SHIFT;
+	cflags |= IORING_CQE_F_BUFFER;
+	req->flags &= ~REQ_F_BUFFER_SELECTED;
+	kfree(kbuf);
+	return cflags;
+}
+
+static inline unsigned int io_put_rw_kbuf(struct io_kiocb *req)
+{
+	struct io_buffer *kbuf;
+
+	if (likely(!(req->flags & REQ_F_BUFFER_SELECTED)))
+		return 0;
+	kbuf = (struct io_buffer *) (unsigned long) req->rw.addr;
+	return io_put_kbuf(req, kbuf);
+}
+
+static inline bool io_run_task_work(void)
+{
+	/*
+	 * PF_IO_WORKER never returns to userspace, so check here if we have
+	 * notify work that needs processing.
+	 */
+	if (current->flags & PF_IO_WORKER &&
+	    test_thread_flag(TIF_NOTIFY_RESUME)) {
+		__set_current_state(TASK_RUNNING);
+		tracehook_notify_resume(NULL);
+	}
+	if (test_thread_flag(TIF_NOTIFY_SIGNAL) || current->task_works) {
+		__set_current_state(TASK_RUNNING);
+		tracehook_notify_signal();
+		return true;
+	}
+
+	return false;
+}
+
+/*
+ * Find and free completed poll iocbs
+ */
+static void io_iopoll_complete(struct io_ring_ctx *ctx, unsigned int *nr_events,
+			       struct list_head *done)
+{
+	struct req_batch rb;
+	struct io_kiocb *req;
+
+	/* order with ->result store in io_complete_rw_iopoll() */
+	smp_rmb();
+
+	io_init_req_batch(&rb);
+	while (!list_empty(done)) {
+		struct io_uring_cqe *cqe;
+		unsigned cflags;
+
+		req = list_first_entry(done, struct io_kiocb, inflight_entry);
+		list_del(&req->inflight_entry);
+		cflags = io_put_rw_kbuf(req);
+		(*nr_events)++;
+
+		cqe = io_get_cqe(ctx);
+		if (cqe) {
+			WRITE_ONCE(cqe->user_data, req->user_data);
+			WRITE_ONCE(cqe->res, req->result);
+			WRITE_ONCE(cqe->flags, cflags);
+		} else {
+			spin_lock(&ctx->completion_lock);
+			io_cqring_event_overflow(ctx, req->user_data,
+							req->result, cflags);
+			spin_unlock(&ctx->completion_lock);
+		}
+
+		if (req_ref_put_and_test(req))
+			io_req_free_batch(&rb, req, &ctx->submit_state);
+	}
+
+	if (io_commit_needs_flush(ctx)) {
+		spin_lock(&ctx->completion_lock);
+		__io_commit_cqring_flush(ctx);
+		spin_unlock(&ctx->completion_lock);
+	}
+	__io_commit_cqring(ctx);
+	io_cqring_ev_posted_iopoll(ctx);
+	io_req_free_batch_finish(ctx, &rb);
+}
+
+static int io_do_iopoll(struct io_ring_ctx *ctx, unsigned int *nr_events,
+			long min)
+{
+	struct io_kiocb *req, *tmp;
+	LIST_HEAD(done);
+	bool spin;
+
+	/*
+	 * Only spin for completions if we don't have multiple devices hanging
+	 * off our complete list, and we're under the requested amount.
+	 */
+	spin = !ctx->poll_multi_queue && *nr_events < min;
+
+	list_for_each_entry_safe(req, tmp, &ctx->iopoll_list, inflight_entry) {
+		struct kiocb *kiocb = &req->rw.kiocb;
+		int ret;
+
+		/*
+		 * Move completed and retryable entries to our local lists.
+		 * If we find a request that requires polling, break out
+		 * and complete those lists first, if we have entries there.
+		 */
+		if (READ_ONCE(req->iopoll_completed)) {
+			list_move_tail(&req->inflight_entry, &done);
+			continue;
+		}
+		if (!list_empty(&done))
+			break;
+
+		ret = kiocb->ki_filp->f_op->iopoll(kiocb, spin);
+		if (unlikely(ret < 0))
+			return ret;
+		else if (ret)
+			spin = false;
+
+		/* iopoll may have completed current req */
+		if (READ_ONCE(req->iopoll_completed))
+			list_move_tail(&req->inflight_entry, &done);
+	}
+
+	if (!list_empty(&done))
+		io_iopoll_complete(ctx, nr_events, &done);
+
+	return 0;
+}
+
+/*
+ * We can't just wait for polled events to come to us, we have to actively
+ * find and complete them.
+ */
+static void io_iopoll_try_reap_events(struct io_ring_ctx *ctx)
+{
+	if (!(ctx->flags & IORING_SETUP_IOPOLL))
+		return;
+
+	percpu_ref_get(&ctx->refs);
+	mutex_lock(&ctx->uring_lock);
+	while (!list_empty(&ctx->iopoll_list)) {
+		unsigned int nr_events = 0;
+
+		io_do_iopoll(ctx, &nr_events, 0);
+
+		/* let it sleep and repeat later if can't complete a request */
+		if (nr_events == 0)
+			break;
+		/*
+		 * Ensure we allow local-to-the-cpu processing to take place,
+		 * in this case we need to ensure that we reap all events.
+		 * Also let task_work, etc. to progress by releasing the mutex
+		 */
+		if (need_resched()) {
+			mutex_unlock(&ctx->uring_lock);
+			cond_resched();
+			mutex_lock(&ctx->uring_lock);
+		}
+	}
+	mutex_unlock(&ctx->uring_lock);
+	percpu_ref_put(&ctx->refs);
+}
+
+static int io_iopoll_check(struct io_ring_ctx *ctx, long min)
+{
+	unsigned int nr_events = 0;
+	int ret = 0;
+
+	/*
+	 * We disallow the app entering submit/complete with polling, but we
+	 * still need to lock the ring to prevent racing with polled issue
+	 * that got punted to a workqueue.
+	 */
+	mutex_lock(&ctx->uring_lock);
+	/*
+	 * Don't enter poll loop if we already have events pending.
+	 * If we do, we can potentially be spinning for commands that
+	 * already triggered a CQE (eg in error).
+	 */
+	if (test_bit(0, &ctx->check_cq_overflow))
+		__io_cqring_overflow_flush(ctx, false);
+	if (io_cqring_events(ctx))
+		goto out;
+	do {
+		/*
+		 * If a submit got punted to a workqueue, we can have the
+		 * application entering polling for a command before it gets
+		 * issued. That app will hold the uring_lock for the duration
+		 * of the poll right here, so we need to take a breather every
+		 * now and then to ensure that the issue has a chance to add
+		 * the poll to the issued list. Otherwise we can spin here
+		 * forever, while the workqueue is stuck trying to acquire the
+		 * very same mutex.
+		 */
+		if (list_empty(&ctx->iopoll_list)) {
+			u32 tail = ctx->cached_cq_tail;
+
+			mutex_unlock(&ctx->uring_lock);
+			io_run_task_work();
+			mutex_lock(&ctx->uring_lock);
+
+			/* some requests don't go through iopoll_list */
+			if (tail != ctx->cached_cq_tail ||
+			    list_empty(&ctx->iopoll_list))
+				break;
+		}
+		ret = io_do_iopoll(ctx, &nr_events, min);
+
+		if (task_sigpending(current)) {
+			ret = -EINTR;
+			goto out;
+		}
+	} while (!ret && nr_events < min && !need_resched());
+out:
+	mutex_unlock(&ctx->uring_lock);
+	return ret;
+}
+
+static void io_req_end_write(struct io_kiocb *req)
+{
+	if (req->flags & REQ_F_ISREG) {
+		struct io_rw *rw = &req->rw;
+
+		kiocb_end_write(&rw->kiocb);
+	}
+}
+
+#ifdef CONFIG_BLOCK
+static bool io_resubmit_prep(struct io_kiocb *req)
+{
+	struct io_async_rw *rw = req->async_data;
+
+	if (!rw)
+		return !io_req_prep_async(req);
+	iov_iter_restore(&rw->iter, &rw->iter_state);
+	return true;
+}
+
+static bool io_rw_should_reissue(struct io_kiocb *req)
+{
+	umode_t mode = file_inode(req->file)->i_mode;
+	struct io_ring_ctx *ctx = req->ctx;
+
+	if (!S_ISBLK(mode) && !S_ISREG(mode))
+		return false;
+	if ((req->flags & REQ_F_NOWAIT) || (io_wq_current_is_worker() &&
+	    !(ctx->flags & IORING_SETUP_IOPOLL)))
+		return false;
+	/*
+	 * If ref is dying, we might be running poll reap from the exit work.
+	 * Don't attempt to reissue from that path, just let it fail with
+	 * -EAGAIN.
+	 */
+	if (percpu_ref_is_dying(&ctx->refs))
+		return false;
+	/*
+	 * Play it safe and assume not safe to re-import and reissue if we're
+	 * not in the original thread group (or in task context).
+	 */
+	if (!same_thread_group(req->task, current) || !in_task())
+		return false;
+	return true;
+}
+#else
+static bool io_resubmit_prep(struct io_kiocb *req)
+{
+	return false;
+}
+static bool io_rw_should_reissue(struct io_kiocb *req)
+{
+	return false;
+}
+#endif
+
+/*
+ * Trigger the notifications after having done some IO, and finish the write
+ * accounting, if any.
+ */
+static void io_req_io_end(struct io_kiocb *req)
+{
+	struct io_rw *rw = &req->rw;
+
+	if (rw->kiocb.ki_flags & IOCB_WRITE) {
+		io_req_end_write(req);
+		fsnotify_modify(req->file);
+	} else {
+		fsnotify_access(req->file);
+	}
+}
+
+static bool __io_complete_rw_common(struct io_kiocb *req, long res)
+{
+	if (res != req->result) {
+		if ((res == -EAGAIN || res == -EOPNOTSUPP) &&
+		    io_rw_should_reissue(req)) {
+			/*
+			 * Reissue will start accounting again, finish the
+			 * current cycle.
+			 */
+			io_req_io_end(req);
+			req->flags |= REQ_F_REISSUE;
+			return true;
+		}
+		req_set_fail(req);
+		req->result = res;
+	}
+	return false;
+}
+
+static inline int io_fixup_rw_res(struct io_kiocb *req, long res)
+{
+	struct io_async_rw *io = req->async_data;
+
+	/* add previously done IO, if any */
+	if (io && io->bytes_done > 0) {
+		if (res < 0)
+			res = io->bytes_done;
+		else
+			res += io->bytes_done;
+	}
+	return res;
+}
+
+static void io_req_task_complete(struct io_kiocb *req, bool *locked)
+{
+	unsigned int cflags = io_put_rw_kbuf(req);
+	int res = req->result;
+
+	if (*locked) {
+		struct io_ring_ctx *ctx = req->ctx;
+		struct io_submit_state *state = &ctx->submit_state;
+
+		io_req_complete_state(req, res, cflags);
+		state->compl_reqs[state->compl_nr++] = req;
+		if (state->compl_nr == ARRAY_SIZE(state->compl_reqs))
+			io_submit_flush_completions(ctx);
+	} else {
+		io_req_complete_post(req, res, cflags);
+	}
+}
+
+static void io_req_rw_complete(struct io_kiocb *req, bool *locked)
+{
+	io_req_io_end(req);
+	io_req_task_complete(req, locked);
+}
+
+static void io_complete_rw(struct kiocb *kiocb, long res, long res2)
+{
+	struct io_kiocb *req = container_of(kiocb, struct io_kiocb, rw.kiocb);
+
+	if (__io_complete_rw_common(req, res))
+		return;
+	req->result = io_fixup_rw_res(req, res);
+	req->io_task_work.func = io_req_rw_complete;
+	io_req_task_work_add(req);
+}
+
+static void io_complete_rw_iopoll(struct kiocb *kiocb, long res, long res2)
+{
+	struct io_kiocb *req = container_of(kiocb, struct io_kiocb, rw.kiocb);
+
+	if (kiocb->ki_flags & IOCB_WRITE)
+		io_req_end_write(req);
+	if (unlikely(res != req->result)) {
+		if (res == -EAGAIN && io_rw_should_reissue(req)) {
+			req->flags |= REQ_F_REISSUE;
+			return;
+		}
+	}
+
+	WRITE_ONCE(req->result, res);
+	/* order with io_iopoll_complete() checking ->result */
+	smp_wmb();
+	WRITE_ONCE(req->iopoll_completed, 1);
+}
+
+/*
+ * After the iocb has been issued, it's safe to be found on the poll list.
+ * Adding the kiocb to the list AFTER submission ensures that we don't
+ * find it from a io_do_iopoll() thread before the issuer is done
+ * accessing the kiocb cookie.
+ */
+static void io_iopoll_req_issued(struct io_kiocb *req)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	const bool in_async = io_wq_current_is_worker();
+
+	/* workqueue context doesn't hold uring_lock, grab it now */
+	if (unlikely(in_async))
+		mutex_lock(&ctx->uring_lock);
+
+	/*
+	 * Track whether we have multiple files in our lists. This will impact
+	 * how we do polling eventually, not spinning if we're on potentially
+	 * different devices.
+	 */
+	if (list_empty(&ctx->iopoll_list)) {
+		ctx->poll_multi_queue = false;
+	} else if (!ctx->poll_multi_queue) {
+		struct io_kiocb *list_req;
+		unsigned int queue_num0, queue_num1;
+
+		list_req = list_first_entry(&ctx->iopoll_list, struct io_kiocb,
+						inflight_entry);
+
+		if (list_req->file != req->file) {
+			ctx->poll_multi_queue = true;
+		} else {
+			queue_num0 = blk_qc_t_to_queue_num(list_req->rw.kiocb.ki_cookie);
+			queue_num1 = blk_qc_t_to_queue_num(req->rw.kiocb.ki_cookie);
+			if (queue_num0 != queue_num1)
+				ctx->poll_multi_queue = true;
+		}
+	}
+
+	/*
+	 * For fast devices, IO may have already completed. If it has, add
+	 * it to the front so we find it first.
+	 */
+	if (READ_ONCE(req->iopoll_completed))
+		list_add(&req->inflight_entry, &ctx->iopoll_list);
+	else
+		list_add_tail(&req->inflight_entry, &ctx->iopoll_list);
+
+	if (unlikely(in_async)) {
+		/*
+		 * If IORING_SETUP_SQPOLL is enabled, sqes are either handle
+		 * in sq thread task context or in io worker task context. If
+		 * current task context is sq thread, we don't need to check
+		 * whether should wake up sq thread.
+		 */
+		if ((ctx->flags & IORING_SETUP_SQPOLL) &&
+		    wq_has_sleeper(&ctx->sq_data->wait))
+			wake_up(&ctx->sq_data->wait);
+
+		mutex_unlock(&ctx->uring_lock);
+	}
+}
+
+static bool io_bdev_nowait(struct block_device *bdev)
+{
+	return !bdev || blk_queue_nowait(bdev_get_queue(bdev));
+}
+
+/*
+ * If we tracked the file through the SCM inflight mechanism, we could support
+ * any file. For now, just ensure that anything potentially problematic is done
+ * inline.
+ */
+static bool __io_file_supports_nowait(struct file *file, int rw)
+{
+	umode_t mode = file_inode(file)->i_mode;
+
+	if (S_ISBLK(mode)) {
+		if (IS_ENABLED(CONFIG_BLOCK) &&
+		    io_bdev_nowait(I_BDEV(file->f_mapping->host)))
+			return true;
+		return false;
+	}
+	if (S_ISSOCK(mode))
+		return true;
+	if (S_ISREG(mode)) {
+		if (IS_ENABLED(CONFIG_BLOCK) &&
+		    io_bdev_nowait(file->f_inode->i_sb->s_bdev) &&
+		    file->f_op != &io_uring_fops)
+			return true;
+		return false;
+	}
+
+	/* any ->read/write should understand O_NONBLOCK */
+	if (file->f_flags & O_NONBLOCK)
+		return true;
+
+	if (!(file->f_mode & FMODE_NOWAIT))
+		return false;
+
+	if (rw == READ)
+		return file->f_op->read_iter != NULL;
+
+	return file->f_op->write_iter != NULL;
+}
+
+static bool io_file_supports_nowait(struct io_kiocb *req, int rw)
+{
+	if (rw == READ && (req->flags & REQ_F_NOWAIT_READ))
+		return true;
+	else if (rw == WRITE && (req->flags & REQ_F_NOWAIT_WRITE))
+		return true;
+
+	return __io_file_supports_nowait(req->file, rw);
+}
+
+static int io_prep_rw(struct io_kiocb *req, const struct io_uring_sqe *sqe,
+		      int rw)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct kiocb *kiocb = &req->rw.kiocb;
+	struct file *file = req->file;
+	unsigned ioprio;
+	int ret;
+
+	if (!io_req_ffs_set(req) && S_ISREG(file_inode(file)->i_mode))
+		req->flags |= REQ_F_ISREG;
+
+	kiocb->ki_pos = READ_ONCE(sqe->off);
+	kiocb->ki_hint = ki_hint_validate(file_write_hint(kiocb->ki_filp));
+	kiocb->ki_flags = iocb_flags(kiocb->ki_filp);
+	ret = kiocb_set_rw_flags(kiocb, READ_ONCE(sqe->rw_flags));
+	if (unlikely(ret))
+		return ret;
+
+	/*
+	 * If the file is marked O_NONBLOCK, still allow retry for it if it
+	 * supports async. Otherwise it's impossible to use O_NONBLOCK files
+	 * reliably. If not, or it IOCB_NOWAIT is set, don't retry.
+	 */
+	if ((kiocb->ki_flags & IOCB_NOWAIT) ||
+	    ((file->f_flags & O_NONBLOCK) && !io_file_supports_nowait(req, rw)))
+		req->flags |= REQ_F_NOWAIT;
+
+	ioprio = READ_ONCE(sqe->ioprio);
+	if (ioprio) {
+		ret = ioprio_check_cap(ioprio);
+		if (ret)
+			return ret;
+
+		kiocb->ki_ioprio = ioprio;
+	} else
+		kiocb->ki_ioprio = get_current_ioprio();
+
+	if (ctx->flags & IORING_SETUP_IOPOLL) {
+		if (!(kiocb->ki_flags & IOCB_DIRECT) ||
+		    !kiocb->ki_filp->f_op->iopoll)
+			return -EOPNOTSUPP;
+
+		kiocb->ki_flags |= IOCB_HIPRI | IOCB_ALLOC_CACHE;
+		kiocb->ki_complete = io_complete_rw_iopoll;
+		req->iopoll_completed = 0;
+	} else {
+		if (kiocb->ki_flags & IOCB_HIPRI)
+			return -EINVAL;
+		kiocb->ki_complete = io_complete_rw;
+	}
+
+	/* used for fixed read/write too - just read unconditionally */
+	req->buf_index = READ_ONCE(sqe->buf_index);
+	req->imu = NULL;
+
+	if (req->opcode == IORING_OP_READ_FIXED ||
+	    req->opcode == IORING_OP_WRITE_FIXED) {
+		struct io_ring_ctx *ctx = req->ctx;
+		u16 index;
+
+		if (unlikely(req->buf_index >= ctx->nr_user_bufs))
+			return -EFAULT;
+		index = array_index_nospec(req->buf_index, ctx->nr_user_bufs);
+		req->imu = ctx->user_bufs[index];
+		io_req_set_rsrc_node(req);
+	}
+
+	req->rw.addr = READ_ONCE(sqe->addr);
+	req->rw.len = READ_ONCE(sqe->len);
+	return 0;
+}
+
+static inline void io_rw_done(struct kiocb *kiocb, ssize_t ret)
+{
+	switch (ret) {
+	case -EIOCBQUEUED:
+		break;
+	case -ERESTARTSYS:
+	case -ERESTARTNOINTR:
+	case -ERESTARTNOHAND:
+	case -ERESTART_RESTARTBLOCK:
+		/*
+		 * We can't just restart the syscall, since previously
+		 * submitted sqes may already be in progress. Just fail this
+		 * IO with EINTR.
+		 */
+		ret = -EINTR;
+		fallthrough;
+	default:
+		kiocb->ki_complete(kiocb, ret, 0);
+	}
+}
+
+static inline loff_t *io_kiocb_update_pos(struct io_kiocb *req)
+{
+	struct kiocb *kiocb = &req->rw.kiocb;
+
+	if (kiocb->ki_pos != -1)
+		return &kiocb->ki_pos;
+
+	if (!(req->file->f_mode & FMODE_STREAM)) {
+		req->flags |= REQ_F_CUR_POS;
+		kiocb->ki_pos = req->file->f_pos;
+		return &kiocb->ki_pos;
+	}
+
+	kiocb->ki_pos = 0;
+	return NULL;
+}
+
+static void kiocb_done(struct kiocb *kiocb, ssize_t ret,
+		       unsigned int issue_flags)
+{
+	struct io_kiocb *req = container_of(kiocb, struct io_kiocb, rw.kiocb);
+
+	if (req->flags & REQ_F_CUR_POS)
+		req->file->f_pos = kiocb->ki_pos;
+	if (ret >= 0 && (kiocb->ki_complete == io_complete_rw)) {
+		if (!__io_complete_rw_common(req, ret)) {
+			/*
+			 * Safe to call io_end from here as we're inline
+			 * from the submission path.
+			 */
+			io_req_io_end(req);
+			__io_req_complete(req, issue_flags,
+					  io_fixup_rw_res(req, ret),
+					  io_put_rw_kbuf(req));
+		}
+	} else {
+		io_rw_done(kiocb, ret);
+	}
+
+	if (req->flags & REQ_F_REISSUE) {
+		req->flags &= ~REQ_F_REISSUE;
+		if (io_resubmit_prep(req)) {
+			io_req_task_queue_reissue(req);
+		} else {
+			unsigned int cflags = io_put_rw_kbuf(req);
+			struct io_ring_ctx *ctx = req->ctx;
+
+			ret = io_fixup_rw_res(req, ret);
+			req_set_fail(req);
+			if (!(issue_flags & IO_URING_F_NONBLOCK)) {
+				mutex_lock(&ctx->uring_lock);
+				__io_req_complete(req, issue_flags, ret, cflags);
+				mutex_unlock(&ctx->uring_lock);
+			} else {
+				__io_req_complete(req, issue_flags, ret, cflags);
+			}
+		}
+	}
+}
+
+static int __io_import_fixed(struct io_kiocb *req, int rw, struct iov_iter *iter,
+			     struct io_mapped_ubuf *imu)
+{
+	size_t len = req->rw.len;
+	u64 buf_end, buf_addr = req->rw.addr;
+	size_t offset;
+
+	if (unlikely(check_add_overflow(buf_addr, (u64)len, &buf_end)))
+		return -EFAULT;
+	/* not inside the mapped region */
+	if (unlikely(buf_addr < imu->ubuf || buf_end > imu->ubuf_end))
+		return -EFAULT;
+
+	/*
+	 * May not be a start of buffer, set size appropriately
+	 * and advance us to the beginning.
+	 */
+	offset = buf_addr - imu->ubuf;
+	iov_iter_bvec(iter, rw, imu->bvec, imu->nr_bvecs, offset + len);
+
+	if (offset) {
+		/*
+		 * Don't use iov_iter_advance() here, as it's really slow for
+		 * using the latter parts of a big fixed buffer - it iterates
+		 * over each segment manually. We can cheat a bit here, because
+		 * we know that:
+		 *
+		 * 1) it's a BVEC iter, we set it up
+		 * 2) all bvecs are PAGE_SIZE in size, except potentially the
+		 *    first and last bvec
+		 *
+		 * So just find our index, and adjust the iterator afterwards.
+		 * If the offset is within the first bvec (or the whole first
+		 * bvec, just use iov_iter_advance(). This makes it easier
+		 * since we can just skip the first segment, which may not
+		 * be PAGE_SIZE aligned.
+		 */
+		const struct bio_vec *bvec = imu->bvec;
+
+		if (offset < bvec->bv_len) {
+			iov_iter_advance(iter, offset);
+		} else {
+			unsigned long seg_skip;
+
+			/* skip first vec */
+			offset -= bvec->bv_len;
+			seg_skip = 1 + (offset >> PAGE_SHIFT);
+
+			iter->bvec = bvec + seg_skip;
+			iter->nr_segs -= seg_skip;
+			iter->count -= bvec->bv_len + offset;
+			iter->iov_offset = offset & ~PAGE_MASK;
+		}
+	}
+
+	return 0;
+}
+
+static int io_import_fixed(struct io_kiocb *req, int rw, struct iov_iter *iter)
+{
+	if (WARN_ON_ONCE(!req->imu))
+		return -EFAULT;
+	return __io_import_fixed(req, rw, iter, req->imu);
+}
+
+static void io_ring_submit_unlock(struct io_ring_ctx *ctx, bool needs_lock)
+{
+	if (needs_lock)
+		mutex_unlock(&ctx->uring_lock);
+}
+
+static void io_ring_submit_lock(struct io_ring_ctx *ctx, bool needs_lock)
+{
+	/*
+	 * "Normal" inline submissions always hold the uring_lock, since we
+	 * grab it from the system call. Same is true for the SQPOLL offload.
+	 * The only exception is when we've detached the request and issue it
+	 * from an async worker thread, grab the lock for that case.
+	 */
+	if (needs_lock)
+		mutex_lock(&ctx->uring_lock);
+}
+
+static struct io_buffer *io_buffer_select(struct io_kiocb *req, size_t *len,
+					  int bgid, struct io_buffer *kbuf,
+					  bool needs_lock)
+{
+	struct io_buffer *head;
+
+	if (req->flags & REQ_F_BUFFER_SELECTED)
+		return kbuf;
+
+	io_ring_submit_lock(req->ctx, needs_lock);
+
+	lockdep_assert_held(&req->ctx->uring_lock);
+
+	head = xa_load(&req->ctx->io_buffers, bgid);
+	if (head) {
+		if (!list_empty(&head->list)) {
+			kbuf = list_last_entry(&head->list, struct io_buffer,
+							list);
+			list_del(&kbuf->list);
+		} else {
+			kbuf = head;
+			xa_erase(&req->ctx->io_buffers, bgid);
+		}
+		if (*len > kbuf->len)
+			*len = kbuf->len;
+	} else {
+		kbuf = ERR_PTR(-ENOBUFS);
+	}
+
+	io_ring_submit_unlock(req->ctx, needs_lock);
+
+	return kbuf;
+}
+
+static void __user *io_rw_buffer_select(struct io_kiocb *req, size_t *len,
+					bool needs_lock)
+{
+	struct io_buffer *kbuf;
+	u16 bgid;
+
+	kbuf = (struct io_buffer *) (unsigned long) req->rw.addr;
+	bgid = req->buf_index;
+	kbuf = io_buffer_select(req, len, bgid, kbuf, needs_lock);
+	if (IS_ERR(kbuf))
+		return kbuf;
+	req->rw.addr = (u64) (unsigned long) kbuf;
+	req->flags |= REQ_F_BUFFER_SELECTED;
+	return u64_to_user_ptr(kbuf->addr);
+}
+
+#ifdef CONFIG_COMPAT
+static ssize_t io_compat_import(struct io_kiocb *req, struct iovec *iov,
+				bool needs_lock)
+{
+	struct compat_iovec __user *uiov;
+	compat_ssize_t clen;
+	void __user *buf;
+	ssize_t len;
+
+	uiov = u64_to_user_ptr(req->rw.addr);
+	if (!access_ok(uiov, sizeof(*uiov)))
+		return -EFAULT;
+	if (__get_user(clen, &uiov->iov_len))
+		return -EFAULT;
+	if (clen < 0)
+		return -EINVAL;
+
+	len = clen;
+	buf = io_rw_buffer_select(req, &len, needs_lock);
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+	iov[0].iov_base = buf;
+	iov[0].iov_len = (compat_size_t) len;
+	return 0;
+}
+#endif
+
+static ssize_t __io_iov_buffer_select(struct io_kiocb *req, struct iovec *iov,
+				      bool needs_lock)
+{
+	struct iovec __user *uiov = u64_to_user_ptr(req->rw.addr);
+	void __user *buf;
+	ssize_t len;
+
+	if (copy_from_user(iov, uiov, sizeof(*uiov)))
+		return -EFAULT;
+
+	len = iov[0].iov_len;
+	if (len < 0)
+		return -EINVAL;
+	buf = io_rw_buffer_select(req, &len, needs_lock);
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+	iov[0].iov_base = buf;
+	iov[0].iov_len = len;
+	return 0;
+}
+
+static ssize_t io_iov_buffer_select(struct io_kiocb *req, struct iovec *iov,
+				    bool needs_lock)
+{
+	if (req->flags & REQ_F_BUFFER_SELECTED) {
+		struct io_buffer *kbuf;
+
+		kbuf = (struct io_buffer *) (unsigned long) req->rw.addr;
+		iov[0].iov_base = u64_to_user_ptr(kbuf->addr);
+		iov[0].iov_len = kbuf->len;
+		return 0;
+	}
+	if (req->rw.len != 1)
+		return -EINVAL;
+
+#ifdef CONFIG_COMPAT
+	if (req->ctx->compat)
+		return io_compat_import(req, iov, needs_lock);
+#endif
+
+	return __io_iov_buffer_select(req, iov, needs_lock);
+}
+
+static int io_import_iovec(int rw, struct io_kiocb *req, struct iovec **iovec,
+			   struct iov_iter *iter, bool needs_lock)
+{
+	void __user *buf = u64_to_user_ptr(req->rw.addr);
+	size_t sqe_len = req->rw.len;
+	u8 opcode = req->opcode;
+	ssize_t ret;
+
+	if (opcode == IORING_OP_READ_FIXED || opcode == IORING_OP_WRITE_FIXED) {
+		*iovec = NULL;
+		return io_import_fixed(req, rw, iter);
+	}
+
+	/* buffer index only valid with fixed read/write, or buffer select  */
+	if (req->buf_index && !(req->flags & REQ_F_BUFFER_SELECT))
+		return -EINVAL;
+
+	if (opcode == IORING_OP_READ || opcode == IORING_OP_WRITE) {
+		if (req->flags & REQ_F_BUFFER_SELECT) {
+			buf = io_rw_buffer_select(req, &sqe_len, needs_lock);
+			if (IS_ERR(buf))
+				return PTR_ERR(buf);
+			req->rw.len = sqe_len;
+		}
+
+		ret = import_single_range(rw, buf, sqe_len, *iovec, iter);
+		*iovec = NULL;
+		return ret;
+	}
+
+	if (req->flags & REQ_F_BUFFER_SELECT) {
+		ret = io_iov_buffer_select(req, *iovec, needs_lock);
+		if (!ret)
+			iov_iter_init(iter, rw, *iovec, 1, (*iovec)->iov_len);
+		*iovec = NULL;
+		return ret;
+	}
+
+	return __import_iovec(rw, buf, sqe_len, UIO_FASTIOV, iovec, iter,
+			      req->ctx->compat);
+}
+
+static inline loff_t *io_kiocb_ppos(struct kiocb *kiocb)
+{
+	return (kiocb->ki_filp->f_mode & FMODE_STREAM) ? NULL : &kiocb->ki_pos;
+}
+
+/*
+ * For files that don't have ->read_iter() and ->write_iter(), handle them
+ * by looping over ->read() or ->write() manually.
+ */
+static ssize_t loop_rw_iter(int rw, struct io_kiocb *req, struct iov_iter *iter)
+{
+	struct kiocb *kiocb = &req->rw.kiocb;
+	struct file *file = req->file;
+	ssize_t ret = 0;
+	loff_t *ppos;
+
+	/*
+	 * Don't support polled IO through this interface, and we can't
+	 * support non-blocking either. For the latter, this just causes
+	 * the kiocb to be handled from an async context.
+	 */
+	if (kiocb->ki_flags & IOCB_HIPRI)
+		return -EOPNOTSUPP;
+	if (kiocb->ki_flags & IOCB_NOWAIT)
+		return -EAGAIN;
+
+	ppos = io_kiocb_ppos(kiocb);
+
+	while (iov_iter_count(iter)) {
+		struct iovec iovec;
+		ssize_t nr;
+
+		if (!iov_iter_is_bvec(iter)) {
+			iovec = iov_iter_iovec(iter);
+		} else {
+			iovec.iov_base = u64_to_user_ptr(req->rw.addr);
+			iovec.iov_len = req->rw.len;
+		}
+
+		if (rw == READ) {
+			nr = file->f_op->read(file, iovec.iov_base,
+					      iovec.iov_len, ppos);
+		} else {
+			nr = file->f_op->write(file, iovec.iov_base,
+					       iovec.iov_len, ppos);
+		}
+
+		if (nr < 0) {
+			if (!ret)
+				ret = nr;
+			break;
+		}
+		ret += nr;
+		if (!iov_iter_is_bvec(iter)) {
+			iov_iter_advance(iter, nr);
+		} else {
+			req->rw.addr += nr;
+			req->rw.len -= nr;
+			if (!req->rw.len)
+				break;
+		}
+		if (nr != iovec.iov_len)
+			break;
+	}
+
+	return ret;
+}
+
+static void io_req_map_rw(struct io_kiocb *req, const struct iovec *iovec,
+			  const struct iovec *fast_iov, struct iov_iter *iter)
+{
+	struct io_async_rw *rw = req->async_data;
+
+	memcpy(&rw->iter, iter, sizeof(*iter));
+	rw->free_iovec = iovec;
+	rw->bytes_done = 0;
+	/* can only be fixed buffers, no need to do anything */
+	if (iov_iter_is_bvec(iter))
+		return;
+	if (!iovec) {
+		unsigned iov_off = 0;
+
+		rw->iter.iov = rw->fast_iov;
+		if (iter->iov != fast_iov) {
+			iov_off = iter->iov - fast_iov;
+			rw->iter.iov += iov_off;
+		}
+		if (rw->fast_iov != fast_iov)
+			memcpy(rw->fast_iov + iov_off, fast_iov + iov_off,
+			       sizeof(struct iovec) * iter->nr_segs);
+	} else {
+		req->flags |= REQ_F_NEED_CLEANUP;
+	}
+}
+
+static inline int io_alloc_async_data(struct io_kiocb *req)
+{
+	WARN_ON_ONCE(!io_op_defs[req->opcode].async_size);
+	req->async_data = kmalloc(io_op_defs[req->opcode].async_size, GFP_KERNEL);
+	return req->async_data == NULL;
+}
+
+static int io_setup_async_rw(struct io_kiocb *req, const struct iovec *iovec,
+			     const struct iovec *fast_iov,
+			     struct iov_iter *iter, bool force)
+{
+	if (!force && !io_op_defs[req->opcode].needs_async_setup)
+		return 0;
+	if (!req->async_data) {
+		struct io_async_rw *iorw;
+
+		if (io_alloc_async_data(req)) {
+			kfree(iovec);
+			return -ENOMEM;
+		}
+
+		io_req_map_rw(req, iovec, fast_iov, iter);
+		iorw = req->async_data;
+		/* we've copied and mapped the iter, ensure state is saved */
+		iov_iter_save_state(&iorw->iter, &iorw->iter_state);
+	}
+	return 0;
+}
+
+static inline int io_rw_prep_async(struct io_kiocb *req, int rw)
+{
+	struct io_async_rw *iorw = req->async_data;
+	struct iovec *iov = iorw->fast_iov;
+	int ret;
+
+	iorw->bytes_done = 0;
+	iorw->free_iovec = NULL;
+
+	ret = io_import_iovec(rw, req, &iov, &iorw->iter, false);
+	if (unlikely(ret < 0))
+		return ret;
+
+	if (iov) {
+		iorw->free_iovec = iov;
+		req->flags |= REQ_F_NEED_CLEANUP;
+	}
+	iov_iter_save_state(&iorw->iter, &iorw->iter_state);
+	return 0;
+}
+
+static int io_read_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	if (unlikely(!(req->file->f_mode & FMODE_READ)))
+		return -EBADF;
+	return io_prep_rw(req, sqe, READ);
+}
+
+/*
+ * This is our waitqueue callback handler, registered through lock_page_async()
+ * when we initially tried to do the IO with the iocb armed our waitqueue.
+ * This gets called when the page is unlocked, and we generally expect that to
+ * happen when the page IO is completed and the page is now uptodate. This will
+ * queue a task_work based retry of the operation, attempting to copy the data
+ * again. If the latter fails because the page was NOT uptodate, then we will
+ * do a thread based blocking retry of the operation. That's the unexpected
+ * slow path.
+ */
+static int io_async_buf_func(struct wait_queue_entry *wait, unsigned mode,
+			     int sync, void *arg)
+{
+	struct wait_page_queue *wpq;
+	struct io_kiocb *req = wait->private;
+	struct wait_page_key *key = arg;
+
+	wpq = container_of(wait, struct wait_page_queue, wait);
+
+	if (!wake_page_match(wpq, key))
+		return 0;
+
+	req->rw.kiocb.ki_flags &= ~IOCB_WAITQ;
+	list_del_init(&wait->entry);
+	io_req_task_queue(req);
+	return 1;
+}
+
+/*
+ * This controls whether a given IO request should be armed for async page
+ * based retry. If we return false here, the request is handed to the async
+ * worker threads for retry. If we're doing buffered reads on a regular file,
+ * we prepare a private wait_page_queue entry and retry the operation. This
+ * will either succeed because the page is now uptodate and unlocked, or it
+ * will register a callback when the page is unlocked at IO completion. Through
+ * that callback, io_uring uses task_work to setup a retry of the operation.
+ * That retry will attempt the buffered read again. The retry will generally
+ * succeed, or in rare cases where it fails, we then fall back to using the
+ * async worker threads for a blocking retry.
+ */
+static bool io_rw_should_retry(struct io_kiocb *req)
+{
+	struct io_async_rw *rw = req->async_data;
+	struct wait_page_queue *wait = &rw->wpq;
+	struct kiocb *kiocb = &req->rw.kiocb;
+
+	/* never retry for NOWAIT, we just complete with -EAGAIN */
+	if (req->flags & REQ_F_NOWAIT)
+		return false;
+
+	/* Only for buffered IO */
+	if (kiocb->ki_flags & (IOCB_DIRECT | IOCB_HIPRI))
+		return false;
+
+	/*
+	 * just use poll if we can, and don't attempt if the fs doesn't
+	 * support callback based unlocks
+	 */
+	if (file_can_poll(req->file) || !(req->file->f_mode & FMODE_BUF_RASYNC))
+		return false;
+
+	wait->wait.func = io_async_buf_func;
+	wait->wait.private = req;
+	wait->wait.flags = 0;
+	INIT_LIST_HEAD(&wait->wait.entry);
+	kiocb->ki_flags |= IOCB_WAITQ;
+	kiocb->ki_flags &= ~IOCB_NOWAIT;
+	kiocb->ki_waitq = wait;
+	return true;
+}
+
+static inline int io_iter_do_read(struct io_kiocb *req, struct iov_iter *iter)
+{
+	if (req->file->f_op->read_iter)
+		return call_read_iter(req->file, &req->rw.kiocb, iter);
+	else if (req->file->f_op->read)
+		return loop_rw_iter(READ, req, iter);
+	else
+		return -EINVAL;
+}
+
+static bool need_read_all(struct io_kiocb *req)
+{
+	return req->flags & REQ_F_ISREG ||
+		S_ISBLK(file_inode(req->file)->i_mode);
+}
+
+static int io_read(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct iovec inline_vecs[UIO_FASTIOV], *iovec = inline_vecs;
+	struct kiocb *kiocb = &req->rw.kiocb;
+	struct iov_iter __iter, *iter = &__iter;
+	struct io_async_rw *rw = req->async_data;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+	struct iov_iter_state __state, *state;
+	ssize_t ret, ret2;
+	loff_t *ppos;
+
+	if (rw) {
+		iter = &rw->iter;
+		state = &rw->iter_state;
+		/*
+		 * We come here from an earlier attempt, restore our state to
+		 * match in case it doesn't. It's cheap enough that we don't
+		 * need to make this conditional.
+		 */
+		iov_iter_restore(iter, state);
+		iovec = NULL;
+	} else {
+		ret = io_import_iovec(READ, req, &iovec, iter, !force_nonblock);
+		if (ret < 0)
+			return ret;
+		state = &__state;
+		iov_iter_save_state(iter, state);
+	}
+	req->result = iov_iter_count(iter);
+
+	/* Ensure we clear previously set non-block flag */
+	if (!force_nonblock)
+		kiocb->ki_flags &= ~IOCB_NOWAIT;
+	else
+		kiocb->ki_flags |= IOCB_NOWAIT;
+
+	/* If the file doesn't support async, just async punt */
+	if (force_nonblock && !io_file_supports_nowait(req, READ)) {
+		ret = io_setup_async_rw(req, iovec, inline_vecs, iter, true);
+		return ret ?: -EAGAIN;
+	}
+
+	ppos = io_kiocb_update_pos(req);
+
+	ret = rw_verify_area(READ, req->file, ppos, req->result);
+	if (unlikely(ret)) {
+		kfree(iovec);
+		return ret;
+	}
+
+	ret = io_iter_do_read(req, iter);
+
+	if (ret == -EAGAIN || (req->flags & REQ_F_REISSUE)) {
+		req->flags &= ~REQ_F_REISSUE;
+		/* IOPOLL retry should happen for io-wq threads */
+		if (!force_nonblock && !(req->ctx->flags & IORING_SETUP_IOPOLL))
+			goto done;
+		/* no retry on NONBLOCK nor RWF_NOWAIT */
+		if (req->flags & REQ_F_NOWAIT)
+			goto done;
+		ret = 0;
+	} else if (ret == -EIOCBQUEUED) {
+		goto out_free;
+	} else if (ret <= 0 || ret == req->result || !force_nonblock ||
+		   (req->flags & REQ_F_NOWAIT) || !need_read_all(req)) {
+		/* read all, failed, already did sync or don't want to retry */
+		goto done;
+	}
+
+	/*
+	 * Don't depend on the iter state matching what was consumed, or being
+	 * untouched in case of error. Restore it and we'll advance it
+	 * manually if we need to.
+	 */
+	iov_iter_restore(iter, state);
+
+	ret2 = io_setup_async_rw(req, iovec, inline_vecs, iter, true);
+	if (ret2)
+		return ret2;
+
+	iovec = NULL;
+	rw = req->async_data;
+	/*
+	 * Now use our persistent iterator and state, if we aren't already.
+	 * We've restored and mapped the iter to match.
+	 */
+	if (iter != &rw->iter) {
+		iter = &rw->iter;
+		state = &rw->iter_state;
+	}
+
+	do {
+		/*
+		 * We end up here because of a partial read, either from
+		 * above or inside this loop. Advance the iter by the bytes
+		 * that were consumed.
+		 */
+		iov_iter_advance(iter, ret);
+		if (!iov_iter_count(iter))
+			break;
+		rw->bytes_done += ret;
+		iov_iter_save_state(iter, state);
+
+		/* if we can retry, do so with the callbacks armed */
+		if (!io_rw_should_retry(req)) {
+			kiocb->ki_flags &= ~IOCB_WAITQ;
+			return -EAGAIN;
+		}
+
+		req->result = iov_iter_count(iter);
+		/*
+		 * Now retry read with the IOCB_WAITQ parts set in the iocb. If
+		 * we get -EIOCBQUEUED, then we'll get a notification when the
+		 * desired page gets unlocked. We can also get a partial read
+		 * here, and if we do, then just retry at the new offset.
+		 */
+		ret = io_iter_do_read(req, iter);
+		if (ret == -EIOCBQUEUED)
+			return 0;
+		/* we got some bytes, but not all. retry. */
+		kiocb->ki_flags &= ~IOCB_WAITQ;
+		iov_iter_restore(iter, state);
+	} while (ret > 0);
+done:
+	kiocb_done(kiocb, ret, issue_flags);
+out_free:
+	/* it's faster to check here then delegate to kfree */
+	if (iovec)
+		kfree(iovec);
+	return 0;
+}
+
+static int io_write_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	if (unlikely(!(req->file->f_mode & FMODE_WRITE)))
+		return -EBADF;
+	return io_prep_rw(req, sqe, WRITE);
+}
+
+static bool io_kiocb_start_write(struct io_kiocb *req, struct kiocb *kiocb)
+{
+	struct inode *inode;
+	bool ret;
+
+	if (!(req->flags & REQ_F_ISREG))
+		return true;
+	if (!(kiocb->ki_flags & IOCB_NOWAIT)) {
+		kiocb_start_write(kiocb);
+		return true;
+	}
+
+	inode = file_inode(kiocb->ki_filp);
+	ret = sb_start_write_trylock(inode->i_sb);
+	if (ret)
+		__sb_writers_release(inode->i_sb, SB_FREEZE_WRITE);
+	return ret;
+}
+
+static int io_write(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct iovec inline_vecs[UIO_FASTIOV], *iovec = inline_vecs;
+	struct kiocb *kiocb = &req->rw.kiocb;
+	struct iov_iter __iter, *iter = &__iter;
+	struct io_async_rw *rw = req->async_data;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+	struct iov_iter_state __state, *state;
+	ssize_t ret, ret2;
+	loff_t *ppos;
+
+	if (rw) {
+		iter = &rw->iter;
+		state = &rw->iter_state;
+		iov_iter_restore(iter, state);
+		iovec = NULL;
+	} else {
+		ret = io_import_iovec(WRITE, req, &iovec, iter, !force_nonblock);
+		if (ret < 0)
+			return ret;
+		state = &__state;
+		iov_iter_save_state(iter, state);
+	}
+	req->result = iov_iter_count(iter);
+
+	/* Ensure we clear previously set non-block flag */
+	if (!force_nonblock)
+		kiocb->ki_flags &= ~IOCB_NOWAIT;
+	else
+		kiocb->ki_flags |= IOCB_NOWAIT;
+
+	/* If the file doesn't support async, just async punt */
+	if (force_nonblock && !io_file_supports_nowait(req, WRITE))
+		goto copy_iov;
+
+	/* file path doesn't support NOWAIT for non-direct_IO */
+	if (force_nonblock && !(kiocb->ki_flags & IOCB_DIRECT) &&
+	    (req->flags & REQ_F_ISREG))
+		goto copy_iov;
+
+	ppos = io_kiocb_update_pos(req);
+
+	ret = rw_verify_area(WRITE, req->file, ppos, req->result);
+	if (unlikely(ret))
+		goto out_free;
+
+	if (unlikely(!io_kiocb_start_write(req, kiocb)))
+		goto copy_iov;
+	kiocb->ki_flags |= IOCB_WRITE;
+
+	if (req->file->f_op->write_iter)
+		ret2 = call_write_iter(req->file, kiocb, iter);
+	else if (req->file->f_op->write)
+		ret2 = loop_rw_iter(WRITE, req, iter);
+	else
+		ret2 = -EINVAL;
+
+	if (req->flags & REQ_F_REISSUE) {
+		req->flags &= ~REQ_F_REISSUE;
+		ret2 = -EAGAIN;
+	}
+
+	/*
+	 * Raw bdev writes will return -EOPNOTSUPP for IOCB_NOWAIT. Just
+	 * retry them without IOCB_NOWAIT.
+	 */
+	if (ret2 == -EOPNOTSUPP && (kiocb->ki_flags & IOCB_NOWAIT))
+		ret2 = -EAGAIN;
+	/* no retry on NONBLOCK nor RWF_NOWAIT */
+	if (ret2 == -EAGAIN && (req->flags & REQ_F_NOWAIT))
+		goto done;
+	if (!force_nonblock || ret2 != -EAGAIN) {
+		/* IOPOLL retry should happen for io-wq threads */
+		if ((req->ctx->flags & IORING_SETUP_IOPOLL) && ret2 == -EAGAIN)
+			goto copy_iov;
+done:
+		kiocb_done(kiocb, ret2, issue_flags);
+	} else {
+copy_iov:
+		iov_iter_restore(iter, state);
+		ret = io_setup_async_rw(req, iovec, inline_vecs, iter, false);
+		if (!ret) {
+			if (kiocb->ki_flags & IOCB_WRITE)
+				io_req_end_write(req);
+			return -EAGAIN;
+		}
+		return ret;
+	}
+out_free:
+	/* it's reportedly faster than delegating the null check to kfree() */
+	if (iovec)
+		kfree(iovec);
+	return ret;
+}
+
+static int io_renameat_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+	struct io_rename *ren = &req->rename;
+	const char __user *oldf, *newf;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->flags & REQ_F_FIXED_FILE))
+		return -EBADF;
+
+	ren->old_dfd = READ_ONCE(sqe->fd);
+	oldf = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	newf = u64_to_user_ptr(READ_ONCE(sqe->addr2));
+	ren->new_dfd = READ_ONCE(sqe->len);
+	ren->flags = READ_ONCE(sqe->rename_flags);
+
+	ren->oldpath = getname(oldf);
+	if (IS_ERR(ren->oldpath))
+		return PTR_ERR(ren->oldpath);
+
+	ren->newpath = getname(newf);
+	if (IS_ERR(ren->newpath)) {
+		putname(ren->oldpath);
+		return PTR_ERR(ren->newpath);
+	}
+
+	req->flags |= REQ_F_NEED_CLEANUP;
+	return 0;
+}
+
+static int io_renameat(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_rename *ren = &req->rename;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = do_renameat2(ren->old_dfd, ren->oldpath, ren->new_dfd,
+				ren->newpath, ren->flags);
+
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_unlinkat_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+	struct io_unlink *un = &req->unlink;
+	const char __user *fname;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->off || sqe->len || sqe->buf_index ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->flags & REQ_F_FIXED_FILE))
+		return -EBADF;
+
+	un->dfd = READ_ONCE(sqe->fd);
+
+	un->flags = READ_ONCE(sqe->unlink_flags);
+	if (un->flags & ~AT_REMOVEDIR)
+		return -EINVAL;
+
+	fname = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	un->filename = getname(fname);
+	if (IS_ERR(un->filename))
+		return PTR_ERR(un->filename);
+
+	req->flags |= REQ_F_NEED_CLEANUP;
+	return 0;
+}
+
+static int io_unlinkat(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_unlink *un = &req->unlink;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	if (un->flags & AT_REMOVEDIR)
+		ret = do_rmdir(un->dfd, un->filename);
+	else
+		ret = do_unlinkat(un->dfd, un->filename);
+
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_mkdirat_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+	struct io_mkdir *mkd = &req->mkdir;
+	const char __user *fname;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->off || sqe->rw_flags || sqe->buf_index ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->flags & REQ_F_FIXED_FILE))
+		return -EBADF;
+
+	mkd->dfd = READ_ONCE(sqe->fd);
+	mkd->mode = READ_ONCE(sqe->len);
+
+	fname = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	mkd->filename = getname(fname);
+	if (IS_ERR(mkd->filename))
+		return PTR_ERR(mkd->filename);
+
+	req->flags |= REQ_F_NEED_CLEANUP;
+	return 0;
+}
+
+static int io_mkdirat(struct io_kiocb *req, int issue_flags)
+{
+	struct io_mkdir *mkd = &req->mkdir;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = do_mkdirat(mkd->dfd, mkd->filename, mkd->mode);
+
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_symlinkat_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+	struct io_symlink *sl = &req->symlink;
+	const char __user *oldpath, *newpath;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->len || sqe->rw_flags || sqe->buf_index ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->flags & REQ_F_FIXED_FILE))
+		return -EBADF;
+
+	sl->new_dfd = READ_ONCE(sqe->fd);
+	oldpath = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	newpath = u64_to_user_ptr(READ_ONCE(sqe->addr2));
+
+	sl->oldpath = getname(oldpath);
+	if (IS_ERR(sl->oldpath))
+		return PTR_ERR(sl->oldpath);
+
+	sl->newpath = getname(newpath);
+	if (IS_ERR(sl->newpath)) {
+		putname(sl->oldpath);
+		return PTR_ERR(sl->newpath);
+	}
+
+	req->flags |= REQ_F_NEED_CLEANUP;
+	return 0;
+}
+
+static int io_symlinkat(struct io_kiocb *req, int issue_flags)
+{
+	struct io_symlink *sl = &req->symlink;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = do_symlinkat(sl->oldpath, sl->new_dfd, sl->newpath);
+
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_linkat_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+	struct io_hardlink *lnk = &req->hardlink;
+	const char __user *oldf, *newf;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->flags & REQ_F_FIXED_FILE))
+		return -EBADF;
+
+	lnk->old_dfd = READ_ONCE(sqe->fd);
+	lnk->new_dfd = READ_ONCE(sqe->len);
+	oldf = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	newf = u64_to_user_ptr(READ_ONCE(sqe->addr2));
+	lnk->flags = READ_ONCE(sqe->hardlink_flags);
+
+	lnk->oldpath = getname_uflags(oldf, lnk->flags);
+	if (IS_ERR(lnk->oldpath))
+		return PTR_ERR(lnk->oldpath);
+
+	lnk->newpath = getname(newf);
+	if (IS_ERR(lnk->newpath)) {
+		putname(lnk->oldpath);
+		return PTR_ERR(lnk->newpath);
+	}
+
+	req->flags |= REQ_F_NEED_CLEANUP;
+	return 0;
+}
+
+static int io_linkat(struct io_kiocb *req, int issue_flags)
+{
+	struct io_hardlink *lnk = &req->hardlink;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = do_linkat(lnk->old_dfd, lnk->oldpath, lnk->new_dfd,
+				lnk->newpath, lnk->flags);
+
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_shutdown_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+#if defined(CONFIG_NET)
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(sqe->ioprio || sqe->off || sqe->addr || sqe->rw_flags ||
+		     sqe->buf_index || sqe->splice_fd_in))
+		return -EINVAL;
+
+	req->shutdown.how = READ_ONCE(sqe->len);
+	return 0;
+#else
+	return -EOPNOTSUPP;
+#endif
+}
+
+static int io_shutdown(struct io_kiocb *req, unsigned int issue_flags)
+{
+#if defined(CONFIG_NET)
+	struct socket *sock;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	sock = sock_from_file(req->file);
+	if (unlikely(!sock))
+		return -ENOTSOCK;
+
+	ret = __sys_shutdown_sock(sock, req->shutdown.how);
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+#else
+	return -EOPNOTSUPP;
+#endif
+}
+
+static int __io_splice_prep(struct io_kiocb *req,
+			    const struct io_uring_sqe *sqe)
+{
+	struct io_splice *sp = &req->splice;
+	unsigned int valid_flags = SPLICE_F_FD_IN_FIXED | SPLICE_F_ALL;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+
+	sp->len = READ_ONCE(sqe->len);
+	sp->flags = READ_ONCE(sqe->splice_flags);
+	if (unlikely(sp->flags & ~valid_flags))
+		return -EINVAL;
+	sp->splice_fd_in = READ_ONCE(sqe->splice_fd_in);
+	return 0;
+}
+
+static int io_tee_prep(struct io_kiocb *req,
+		       const struct io_uring_sqe *sqe)
+{
+	if (READ_ONCE(sqe->splice_off_in) || READ_ONCE(sqe->off))
+		return -EINVAL;
+	return __io_splice_prep(req, sqe);
+}
+
+static int io_tee(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_splice *sp = &req->splice;
+	struct file *out = sp->file_out;
+	unsigned int flags = sp->flags & ~SPLICE_F_FD_IN_FIXED;
+	struct file *in;
+	long ret = 0;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	in = io_file_get(req->ctx, req, sp->splice_fd_in,
+			 (sp->flags & SPLICE_F_FD_IN_FIXED), issue_flags);
+	if (!in) {
+		ret = -EBADF;
+		goto done;
+	}
+
+	if (sp->len)
+		ret = do_tee(in, out, sp->len, flags);
+
+	if (!(sp->flags & SPLICE_F_FD_IN_FIXED))
+		io_put_file(in);
+done:
+	if (ret != sp->len)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_splice_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_splice *sp = &req->splice;
+
+	sp->off_in = READ_ONCE(sqe->splice_off_in);
+	sp->off_out = READ_ONCE(sqe->off);
+	return __io_splice_prep(req, sqe);
+}
+
+static int io_splice(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_splice *sp = &req->splice;
+	struct file *out = sp->file_out;
+	unsigned int flags = sp->flags & ~SPLICE_F_FD_IN_FIXED;
+	loff_t *poff_in, *poff_out;
+	struct file *in;
+	long ret = 0;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	in = io_file_get(req->ctx, req, sp->splice_fd_in,
+			 (sp->flags & SPLICE_F_FD_IN_FIXED), issue_flags);
+	if (!in) {
+		ret = -EBADF;
+		goto done;
+	}
+
+	poff_in = (sp->off_in == -1) ? NULL : &sp->off_in;
+	poff_out = (sp->off_out == -1) ? NULL : &sp->off_out;
+
+	if (sp->len)
+		ret = do_splice(in, poff_in, out, poff_out, sp->len, flags);
+
+	if (!(sp->flags & SPLICE_F_FD_IN_FIXED))
+		io_put_file(in);
+done:
+	if (ret != sp->len)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+/*
+ * IORING_OP_NOP just posts a completion event, nothing else.
+ */
+static int io_nop(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	if (unlikely(ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+
+	__io_req_complete(req, issue_flags, 0, 0);
+	return 0;
+}
+
+static int io_fsync_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	if (unlikely(ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(sqe->addr || sqe->ioprio || sqe->buf_index ||
+		     sqe->splice_fd_in))
+		return -EINVAL;
+
+	req->sync.flags = READ_ONCE(sqe->fsync_flags);
+	if (unlikely(req->sync.flags & ~IORING_FSYNC_DATASYNC))
+		return -EINVAL;
+
+	req->sync.off = READ_ONCE(sqe->off);
+	req->sync.len = READ_ONCE(sqe->len);
+	return 0;
+}
+
+static int io_fsync(struct io_kiocb *req, unsigned int issue_flags)
+{
+	loff_t end = req->sync.off + req->sync.len;
+	int ret;
+
+	/* fsync always requires a blocking context */
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = vfs_fsync_range(req->file, req->sync.off,
+				end > 0 ? end : LLONG_MAX,
+				req->sync.flags & IORING_FSYNC_DATASYNC);
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_fallocate_prep(struct io_kiocb *req,
+			     const struct io_uring_sqe *sqe)
+{
+	if (sqe->ioprio || sqe->buf_index || sqe->rw_flags ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+
+	req->sync.off = READ_ONCE(sqe->off);
+	req->sync.len = READ_ONCE(sqe->addr);
+	req->sync.mode = READ_ONCE(sqe->len);
+	return 0;
+}
+
+static int io_fallocate(struct io_kiocb *req, unsigned int issue_flags)
+{
+	int ret;
+
+	/* fallocate always requiring blocking context */
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+	ret = vfs_fallocate(req->file, req->sync.mode, req->sync.off,
+				req->sync.len);
+	if (ret < 0)
+		req_set_fail(req);
+	else
+		fsnotify_modify(req->file);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int __io_openat_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	const char __user *fname;
+	int ret;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(sqe->ioprio || sqe->buf_index))
+		return -EINVAL;
+	if (unlikely(req->flags & REQ_F_FIXED_FILE))
+		return -EBADF;
+
+	/* open.how should be already initialised */
+	if (!(req->open.how.flags & O_PATH) && force_o_largefile())
+		req->open.how.flags |= O_LARGEFILE;
+
+	req->open.dfd = READ_ONCE(sqe->fd);
+	fname = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	req->open.filename = getname(fname);
+	if (IS_ERR(req->open.filename)) {
+		ret = PTR_ERR(req->open.filename);
+		req->open.filename = NULL;
+		return ret;
+	}
+
+	req->open.file_slot = READ_ONCE(sqe->file_index);
+	if (req->open.file_slot && (req->open.how.flags & O_CLOEXEC))
+		return -EINVAL;
+
+	req->open.nofile = rlimit(RLIMIT_NOFILE);
+	req->flags |= REQ_F_NEED_CLEANUP;
+	return 0;
+}
+
+static int io_openat_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	u64 mode = READ_ONCE(sqe->len);
+	u64 flags = READ_ONCE(sqe->open_flags);
+
+	req->open.how = build_open_how(flags, mode);
+	return __io_openat_prep(req, sqe);
+}
+
+static int io_openat2_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct open_how __user *how;
+	size_t len;
+	int ret;
+
+	how = u64_to_user_ptr(READ_ONCE(sqe->addr2));
+	len = READ_ONCE(sqe->len);
+	if (len < OPEN_HOW_SIZE_VER0)
+		return -EINVAL;
+
+	ret = copy_struct_from_user(&req->open.how, sizeof(req->open.how), how,
+					len);
+	if (ret)
+		return ret;
+
+	return __io_openat_prep(req, sqe);
+}
+
+static int io_openat2(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct open_flags op;
+	struct file *file;
+	bool resolve_nonblock, nonblock_set;
+	bool fixed = !!req->open.file_slot;
+	int ret;
+
+	ret = build_open_flags(&req->open.how, &op);
+	if (ret)
+		goto err;
+	nonblock_set = op.open_flag & O_NONBLOCK;
+	resolve_nonblock = req->open.how.resolve & RESOLVE_CACHED;
+	if (issue_flags & IO_URING_F_NONBLOCK) {
+		/*
+		 * Don't bother trying for O_TRUNC, O_CREAT, or O_TMPFILE open,
+		 * it'll always -EAGAIN. Note that we test for __O_TMPFILE
+		 * because O_TMPFILE includes O_DIRECTORY, which isn't a flag
+		 * we need to force async for.
+		 */
+		if (req->open.how.flags & (O_TRUNC | O_CREAT | __O_TMPFILE))
+			return -EAGAIN;
+		op.lookup_flags |= LOOKUP_CACHED;
+		op.open_flag |= O_NONBLOCK;
+	}
+
+	if (!fixed) {
+		ret = __get_unused_fd_flags(req->open.how.flags, req->open.nofile);
+		if (ret < 0)
+			goto err;
+	}
+
+	file = do_filp_open(req->open.dfd, req->open.filename, &op);
+	if (IS_ERR(file)) {
+		/*
+		 * We could hang on to this 'fd' on retrying, but seems like
+		 * marginal gain for something that is now known to be a slower
+		 * path. So just put it, and we'll get a new one when we retry.
+		 */
+		if (!fixed)
+			put_unused_fd(ret);
+
+		ret = PTR_ERR(file);
+		/* only retry if RESOLVE_CACHED wasn't already set by application */
+		if (ret == -EAGAIN &&
+		    (!resolve_nonblock && (issue_flags & IO_URING_F_NONBLOCK)))
+			return -EAGAIN;
+		goto err;
+	}
+
+	if ((issue_flags & IO_URING_F_NONBLOCK) && !nonblock_set)
+		file->f_flags &= ~O_NONBLOCK;
+	fsnotify_open(file);
+
+	if (!fixed)
+		fd_install(ret, file);
+	else
+		ret = io_install_fixed_file(req, file, issue_flags,
+					    req->open.file_slot - 1);
+err:
+	putname(req->open.filename);
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret < 0)
+		req_set_fail(req);
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_openat(struct io_kiocb *req, unsigned int issue_flags)
+{
+	return io_openat2(req, issue_flags);
+}
+
+static int io_remove_buffers_prep(struct io_kiocb *req,
+				  const struct io_uring_sqe *sqe)
+{
+	struct io_provide_buf *p = &req->pbuf;
+	u64 tmp;
+
+	if (sqe->ioprio || sqe->rw_flags || sqe->addr || sqe->len || sqe->off ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+
+	tmp = READ_ONCE(sqe->fd);
+	if (!tmp || tmp > USHRT_MAX)
+		return -EINVAL;
+
+	memset(p, 0, sizeof(*p));
+	p->nbufs = tmp;
+	p->bgid = READ_ONCE(sqe->buf_group);
+	return 0;
+}
+
+static int __io_remove_buffers(struct io_ring_ctx *ctx, struct io_buffer *buf,
+			       int bgid, unsigned nbufs)
+{
+	unsigned i = 0;
+
+	/* shouldn't happen */
+	if (!nbufs)
+		return 0;
+
+	/* the head kbuf is the list itself */
+	while (!list_empty(&buf->list)) {
+		struct io_buffer *nxt;
+
+		nxt = list_first_entry(&buf->list, struct io_buffer, list);
+		list_del(&nxt->list);
+		kfree(nxt);
+		if (++i == nbufs)
+			return i;
+		cond_resched();
+	}
+	i++;
+	kfree(buf);
+	xa_erase(&ctx->io_buffers, bgid);
+
+	return i;
+}
+
+static int io_remove_buffers(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_provide_buf *p = &req->pbuf;
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_buffer *head;
+	int ret = 0;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+
+	io_ring_submit_lock(ctx, !force_nonblock);
+
+	lockdep_assert_held(&ctx->uring_lock);
+
+	ret = -ENOENT;
+	head = xa_load(&ctx->io_buffers, p->bgid);
+	if (head)
+		ret = __io_remove_buffers(ctx, head, p->bgid, p->nbufs);
+	if (ret < 0)
+		req_set_fail(req);
+
+	/* complete before unlock, IOPOLL may need the lock */
+	__io_req_complete(req, issue_flags, ret, 0);
+	io_ring_submit_unlock(ctx, !force_nonblock);
+	return 0;
+}
+
+static int io_provide_buffers_prep(struct io_kiocb *req,
+				   const struct io_uring_sqe *sqe)
+{
+	unsigned long size, tmp_check;
+	struct io_provide_buf *p = &req->pbuf;
+	u64 tmp;
+
+	if (sqe->ioprio || sqe->rw_flags || sqe->splice_fd_in)
+		return -EINVAL;
+
+	tmp = READ_ONCE(sqe->fd);
+	if (!tmp || tmp > USHRT_MAX)
+		return -E2BIG;
+	p->nbufs = tmp;
+	p->addr = READ_ONCE(sqe->addr);
+	p->len = READ_ONCE(sqe->len);
+
+	if (check_mul_overflow((unsigned long)p->len, (unsigned long)p->nbufs,
+				&size))
+		return -EOVERFLOW;
+	if (check_add_overflow((unsigned long)p->addr, size, &tmp_check))
+		return -EOVERFLOW;
+
+	size = (unsigned long)p->len * p->nbufs;
+	if (!access_ok(u64_to_user_ptr(p->addr), size))
+		return -EFAULT;
+
+	p->bgid = READ_ONCE(sqe->buf_group);
+	tmp = READ_ONCE(sqe->off);
+	if (tmp > USHRT_MAX)
+		return -E2BIG;
+	p->bid = tmp;
+	return 0;
+}
+
+static int io_add_buffers(struct io_provide_buf *pbuf, struct io_buffer **head)
+{
+	struct io_buffer *buf;
+	u64 addr = pbuf->addr;
+	int i, bid = pbuf->bid;
+
+	for (i = 0; i < pbuf->nbufs; i++) {
+		buf = kmalloc(sizeof(*buf), GFP_KERNEL_ACCOUNT);
+		if (!buf)
+			break;
+
+		buf->addr = addr;
+		buf->len = min_t(__u32, pbuf->len, MAX_RW_COUNT);
+		buf->bid = bid;
+		addr += pbuf->len;
+		bid++;
+		if (!*head) {
+			INIT_LIST_HEAD(&buf->list);
+			*head = buf;
+		} else {
+			list_add_tail(&buf->list, &(*head)->list);
+		}
+		cond_resched();
+	}
+
+	return i ? i : -ENOMEM;
+}
+
+static int io_provide_buffers(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_provide_buf *p = &req->pbuf;
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_buffer *head, *list;
+	int ret = 0;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+
+	io_ring_submit_lock(ctx, !force_nonblock);
+
+	lockdep_assert_held(&ctx->uring_lock);
+
+	list = head = xa_load(&ctx->io_buffers, p->bgid);
+
+	ret = io_add_buffers(p, &head);
+	if (ret >= 0 && !list) {
+		ret = xa_insert(&ctx->io_buffers, p->bgid, head,
+				GFP_KERNEL_ACCOUNT);
+		if (ret < 0)
+			__io_remove_buffers(ctx, head, p->bgid, -1U);
+	}
+	if (ret < 0)
+		req_set_fail(req);
+	/* complete before unlock, IOPOLL may need the lock */
+	__io_req_complete(req, issue_flags, ret, 0);
+	io_ring_submit_unlock(ctx, !force_nonblock);
+	return 0;
+}
+
+static int io_epoll_ctl_prep(struct io_kiocb *req,
+			     const struct io_uring_sqe *sqe)
+{
+#if defined(CONFIG_EPOLL)
+	if (sqe->ioprio || sqe->buf_index || sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+
+	req->epoll.epfd = READ_ONCE(sqe->fd);
+	req->epoll.op = READ_ONCE(sqe->len);
+	req->epoll.fd = READ_ONCE(sqe->off);
+
+	if (ep_op_has_event(req->epoll.op)) {
+		struct epoll_event __user *ev;
+
+		ev = u64_to_user_ptr(READ_ONCE(sqe->addr));
+		if (copy_from_user(&req->epoll.event, ev, sizeof(*ev)))
+			return -EFAULT;
+	}
+
+	return 0;
+#else
+	return -EOPNOTSUPP;
+#endif
+}
+
+static int io_epoll_ctl(struct io_kiocb *req, unsigned int issue_flags)
+{
+#if defined(CONFIG_EPOLL)
+	struct io_epoll *ie = &req->epoll;
+	int ret;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+
+	ret = do_epoll_ctl(ie->epfd, ie->op, ie->fd, &ie->event, force_nonblock);
+	if (force_nonblock && ret == -EAGAIN)
+		return -EAGAIN;
+
+	if (ret < 0)
+		req_set_fail(req);
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+#else
+	return -EOPNOTSUPP;
+#endif
+}
+
+static int io_madvise_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+#if defined(CONFIG_ADVISE_SYSCALLS) && defined(CONFIG_MMU)
+	if (sqe->ioprio || sqe->buf_index || sqe->off || sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+
+	req->madvise.addr = READ_ONCE(sqe->addr);
+	req->madvise.len = READ_ONCE(sqe->len);
+	req->madvise.advice = READ_ONCE(sqe->fadvise_advice);
+	return 0;
+#else
+	return -EOPNOTSUPP;
+#endif
+}
+
+static int io_madvise(struct io_kiocb *req, unsigned int issue_flags)
+{
+#if defined(CONFIG_ADVISE_SYSCALLS) && defined(CONFIG_MMU)
+	struct io_madvise *ma = &req->madvise;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = do_madvise(current->mm, ma->addr, ma->len, ma->advice);
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+#else
+	return -EOPNOTSUPP;
+#endif
+}
+
+static int io_fadvise_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	if (sqe->ioprio || sqe->buf_index || sqe->addr || sqe->splice_fd_in)
+		return -EINVAL;
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+
+	req->fadvise.offset = READ_ONCE(sqe->off);
+	req->fadvise.len = READ_ONCE(sqe->len);
+	req->fadvise.advice = READ_ONCE(sqe->fadvise_advice);
+	return 0;
+}
+
+static int io_fadvise(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_fadvise *fa = &req->fadvise;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK) {
+		switch (fa->advice) {
+		case POSIX_FADV_NORMAL:
+		case POSIX_FADV_RANDOM:
+		case POSIX_FADV_SEQUENTIAL:
+			break;
+		default:
+			return -EAGAIN;
+		}
+	}
+
+	ret = vfs_fadvise(req->file, fa->offset, fa->len, fa->advice);
+	if (ret < 0)
+		req_set_fail(req);
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_statx_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->splice_fd_in)
+		return -EINVAL;
+	if (req->flags & REQ_F_FIXED_FILE)
+		return -EBADF;
+
+	req->statx.dfd = READ_ONCE(sqe->fd);
+	req->statx.mask = READ_ONCE(sqe->len);
+	req->statx.filename = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	req->statx.buffer = u64_to_user_ptr(READ_ONCE(sqe->addr2));
+	req->statx.flags = READ_ONCE(sqe->statx_flags);
+
+	return 0;
+}
+
+static int io_statx(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_statx *ctx = &req->statx;
+	int ret;
+
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = do_statx(ctx->dfd, ctx->filename, ctx->flags, ctx->mask,
+		       ctx->buffer);
+
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+static int io_close_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->off || sqe->addr || sqe->len ||
+	    sqe->rw_flags || sqe->buf_index)
+		return -EINVAL;
+	if (req->flags & REQ_F_FIXED_FILE)
+		return -EBADF;
+
+	req->close.fd = READ_ONCE(sqe->fd);
+	req->close.file_slot = READ_ONCE(sqe->file_index);
+	if (req->close.file_slot && req->close.fd)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int io_close(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct files_struct *files = current->files;
+	struct io_close *close = &req->close;
+	struct fdtable *fdt;
+	struct file *file = NULL;
+	int ret = -EBADF;
+
+	if (req->close.file_slot) {
+		ret = io_close_fixed(req, issue_flags);
+		goto err;
+	}
+
+	spin_lock(&files->file_lock);
+	fdt = files_fdtable(files);
+	if (close->fd >= fdt->max_fds) {
+		spin_unlock(&files->file_lock);
+		goto err;
+	}
+	file = fdt->fd[close->fd];
+	if (!file || file->f_op == &io_uring_fops) {
+		spin_unlock(&files->file_lock);
+		file = NULL;
+		goto err;
+	}
+
+	/* if the file has a flush method, be safe and punt to async */
+	if (file->f_op->flush && (issue_flags & IO_URING_F_NONBLOCK)) {
+		spin_unlock(&files->file_lock);
+		return -EAGAIN;
+	}
+
+	ret = __close_fd_get_file(close->fd, &file);
+	spin_unlock(&files->file_lock);
+	if (ret < 0) {
+		if (ret == -ENOENT)
+			ret = -EBADF;
+		goto err;
+	}
+
+	/* No ->flush() or already async, safely close from here */
+	ret = filp_close(file, current->files);
+err:
+	if (ret < 0)
+		req_set_fail(req);
+	if (file)
+		fput(file);
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_sfr_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	if (unlikely(ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(sqe->addr || sqe->ioprio || sqe->buf_index ||
+		     sqe->splice_fd_in))
+		return -EINVAL;
+
+	req->sync.off = READ_ONCE(sqe->off);
+	req->sync.len = READ_ONCE(sqe->len);
+	req->sync.flags = READ_ONCE(sqe->sync_range_flags);
+	return 0;
+}
+
+static int io_sync_file_range(struct io_kiocb *req, unsigned int issue_flags)
+{
+	int ret;
+
+	/* sync_file_range always requires a blocking context */
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		return -EAGAIN;
+
+	ret = sync_file_range(req->file, req->sync.off, req->sync.len,
+				req->sync.flags);
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete(req, ret);
+	return 0;
+}
+
+#if defined(CONFIG_NET)
+static bool io_net_retry(struct socket *sock, int flags)
+{
+	if (!(flags & MSG_WAITALL))
+		return false;
+	return sock->type == SOCK_STREAM || sock->type == SOCK_SEQPACKET;
+}
+
+static int io_setup_async_msg(struct io_kiocb *req,
+			      struct io_async_msghdr *kmsg)
+{
+	struct io_async_msghdr *async_msg = req->async_data;
+
+	if (async_msg)
+		return -EAGAIN;
+	if (io_alloc_async_data(req)) {
+		kfree(kmsg->free_iov);
+		return -ENOMEM;
+	}
+	async_msg = req->async_data;
+	req->flags |= REQ_F_NEED_CLEANUP;
+	memcpy(async_msg, kmsg, sizeof(*kmsg));
+	if (async_msg->msg.msg_name)
+		async_msg->msg.msg_name = &async_msg->addr;
+	/* if were using fast_iov, set it to the new one */
+	if (!kmsg->free_iov) {
+		size_t fast_idx = kmsg->msg.msg_iter.iov - kmsg->fast_iov;
+		async_msg->msg.msg_iter.iov = &async_msg->fast_iov[fast_idx];
+	}
+
+	return -EAGAIN;
+}
+
+static int io_sendmsg_copy_hdr(struct io_kiocb *req,
+			       struct io_async_msghdr *iomsg)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+	int ret;
+
+	iomsg->msg.msg_name = &iomsg->addr;
+	iomsg->free_iov = iomsg->fast_iov;
+	ret = sendmsg_copy_msghdr(&iomsg->msg, req->sr_msg.umsg,
+				   req->sr_msg.msg_flags, &iomsg->free_iov);
+	/* save msg_control as sys_sendmsg() overwrites it */
+	sr->msg_control = iomsg->msg.msg_control;
+	return ret;
+}
+
+static int io_sendmsg_prep_async(struct io_kiocb *req)
+{
+	int ret;
+
+	ret = io_sendmsg_copy_hdr(req, req->async_data);
+	if (!ret)
+		req->flags |= REQ_F_NEED_CLEANUP;
+	return ret;
+}
+
+static int io_sendmsg_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(sqe->addr2 || sqe->file_index))
+		return -EINVAL;
+	if (unlikely(sqe->addr2 || sqe->file_index || sqe->ioprio))
+		return -EINVAL;
+
+	sr->umsg = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	sr->len = READ_ONCE(sqe->len);
+	sr->msg_flags = READ_ONCE(sqe->msg_flags) | MSG_NOSIGNAL;
+	if (sr->msg_flags & MSG_DONTWAIT)
+		req->flags |= REQ_F_NOWAIT;
+
+#ifdef CONFIG_COMPAT
+	if (req->ctx->compat)
+		sr->msg_flags |= MSG_CMSG_COMPAT;
+#endif
+	sr->done_io = 0;
+	return 0;
+}
+
+static int io_sendmsg(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_async_msghdr iomsg, *kmsg;
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct socket *sock;
+	unsigned flags;
+	int min_ret = 0;
+	int ret;
+
+	sock = sock_from_file(req->file);
+	if (unlikely(!sock))
+		return -ENOTSOCK;
+
+	kmsg = req->async_data;
+	if (!kmsg) {
+		ret = io_sendmsg_copy_hdr(req, &iomsg);
+		if (ret)
+			return ret;
+		kmsg = &iomsg;
+	} else {
+		kmsg->msg.msg_control = sr->msg_control;
+	}
+
+	flags = req->sr_msg.msg_flags;
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		flags |= MSG_DONTWAIT;
+	if (flags & MSG_WAITALL)
+		min_ret = iov_iter_count(&kmsg->msg.msg_iter);
+
+	ret = __sys_sendmsg_sock(sock, &kmsg->msg, flags);
+
+	if (ret < min_ret) {
+		if (ret == -EAGAIN && (issue_flags & IO_URING_F_NONBLOCK))
+			return io_setup_async_msg(req, kmsg);
+		if (ret == -ERESTARTSYS)
+			ret = -EINTR;
+		if (ret > 0 && io_net_retry(sock, flags)) {
+			kmsg->msg.msg_controllen = 0;
+			kmsg->msg.msg_control = NULL;
+			sr->done_io += ret;
+			req->flags |= REQ_F_PARTIAL_IO;
+			return io_setup_async_msg(req, kmsg);
+		}
+		req_set_fail(req);
+	}
+	/* fast path, check for non-NULL to avoid function call */
+	if (kmsg->free_iov)
+		kfree(kmsg->free_iov);
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret >= 0)
+		ret += sr->done_io;
+	else if (sr->done_io)
+		ret = sr->done_io;
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_send(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct msghdr msg;
+	struct iovec iov;
+	struct socket *sock;
+	unsigned flags;
+	int min_ret = 0;
+	int ret;
+
+	sock = sock_from_file(req->file);
+	if (unlikely(!sock))
+		return -ENOTSOCK;
+
+	ret = import_single_range(WRITE, sr->buf, sr->len, &iov, &msg.msg_iter);
+	if (unlikely(ret))
+		return ret;
+
+	msg.msg_name = NULL;
+	msg.msg_control = NULL;
+	msg.msg_controllen = 0;
+	msg.msg_namelen = 0;
+
+	flags = req->sr_msg.msg_flags;
+	if (issue_flags & IO_URING_F_NONBLOCK)
+		flags |= MSG_DONTWAIT;
+	if (flags & MSG_WAITALL)
+		min_ret = iov_iter_count(&msg.msg_iter);
+
+	msg.msg_flags = flags;
+	ret = sock_sendmsg(sock, &msg);
+	if (ret < min_ret) {
+		if (ret == -EAGAIN && (issue_flags & IO_URING_F_NONBLOCK))
+			return -EAGAIN;
+		if (ret == -ERESTARTSYS)
+			ret = -EINTR;
+		if (ret > 0 && io_net_retry(sock, flags)) {
+			sr->len -= ret;
+			sr->buf += ret;
+			sr->done_io += ret;
+			req->flags |= REQ_F_PARTIAL_IO;
+			return -EAGAIN;
+		}
+		req_set_fail(req);
+	}
+	if (ret >= 0)
+		ret += sr->done_io;
+	else if (sr->done_io)
+		ret = sr->done_io;
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int __io_recvmsg_copy_hdr(struct io_kiocb *req,
+				 struct io_async_msghdr *iomsg)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct iovec __user *uiov;
+	size_t iov_len;
+	int ret;
+
+	ret = __copy_msghdr_from_user(&iomsg->msg, sr->umsg,
+					&iomsg->uaddr, &uiov, &iov_len);
+	if (ret)
+		return ret;
+
+	if (req->flags & REQ_F_BUFFER_SELECT) {
+		if (iov_len > 1)
+			return -EINVAL;
+		if (copy_from_user(iomsg->fast_iov, uiov, sizeof(*uiov)))
+			return -EFAULT;
+		sr->len = iomsg->fast_iov[0].iov_len;
+		iomsg->free_iov = NULL;
+	} else {
+		iomsg->free_iov = iomsg->fast_iov;
+		ret = __import_iovec(READ, uiov, iov_len, UIO_FASTIOV,
+				     &iomsg->free_iov, &iomsg->msg.msg_iter,
+				     false);
+		if (ret > 0)
+			ret = 0;
+	}
+
+	return ret;
+}
+
+#ifdef CONFIG_COMPAT
+static int __io_compat_recvmsg_copy_hdr(struct io_kiocb *req,
+					struct io_async_msghdr *iomsg)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct compat_iovec __user *uiov;
+	compat_uptr_t ptr;
+	compat_size_t len;
+	int ret;
+
+	ret = __get_compat_msghdr(&iomsg->msg, sr->umsg_compat, &iomsg->uaddr,
+				  &ptr, &len);
+	if (ret)
+		return ret;
+
+	uiov = compat_ptr(ptr);
+	if (req->flags & REQ_F_BUFFER_SELECT) {
+		compat_ssize_t clen;
+
+		if (len > 1)
+			return -EINVAL;
+		if (!access_ok(uiov, sizeof(*uiov)))
+			return -EFAULT;
+		if (__get_user(clen, &uiov->iov_len))
+			return -EFAULT;
+		if (clen < 0)
+			return -EINVAL;
+		sr->len = clen;
+		iomsg->free_iov = NULL;
+	} else {
+		iomsg->free_iov = iomsg->fast_iov;
+		ret = __import_iovec(READ, (struct iovec __user *)uiov, len,
+				   UIO_FASTIOV, &iomsg->free_iov,
+				   &iomsg->msg.msg_iter, true);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+static int io_recvmsg_copy_hdr(struct io_kiocb *req,
+			       struct io_async_msghdr *iomsg)
+{
+	iomsg->msg.msg_name = &iomsg->addr;
+
+#ifdef CONFIG_COMPAT
+	if (req->ctx->compat)
+		return __io_compat_recvmsg_copy_hdr(req, iomsg);
+#endif
+
+	return __io_recvmsg_copy_hdr(req, iomsg);
+}
+
+static struct io_buffer *io_recv_buffer_select(struct io_kiocb *req,
+					       bool needs_lock)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct io_buffer *kbuf;
+
+	kbuf = io_buffer_select(req, &sr->len, sr->bgid, sr->kbuf, needs_lock);
+	if (IS_ERR(kbuf))
+		return kbuf;
+
+	sr->kbuf = kbuf;
+	req->flags |= REQ_F_BUFFER_SELECTED;
+	return kbuf;
+}
+
+static inline unsigned int io_put_recv_kbuf(struct io_kiocb *req)
+{
+	return io_put_kbuf(req, req->sr_msg.kbuf);
+}
+
+static int io_recvmsg_prep_async(struct io_kiocb *req)
+{
+	int ret;
+
+	ret = io_recvmsg_copy_hdr(req, req->async_data);
+	if (!ret)
+		req->flags |= REQ_F_NEED_CLEANUP;
+	return ret;
+}
+
+static int io_recvmsg_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_sr_msg *sr = &req->sr_msg;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(sqe->addr2 || sqe->file_index))
+		return -EINVAL;
+	if (unlikely(sqe->addr2 || sqe->file_index || sqe->ioprio))
+		return -EINVAL;
+
+	sr->umsg = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	sr->len = READ_ONCE(sqe->len);
+	sr->bgid = READ_ONCE(sqe->buf_group);
+	sr->msg_flags = READ_ONCE(sqe->msg_flags);
+	if (sr->msg_flags & MSG_DONTWAIT)
+		req->flags |= REQ_F_NOWAIT;
+
+#ifdef CONFIG_COMPAT
+	if (req->ctx->compat)
+		sr->msg_flags |= MSG_CMSG_COMPAT;
+#endif
+	sr->done_io = 0;
+	return 0;
+}
+
+static int io_recvmsg(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_async_msghdr iomsg, *kmsg;
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct socket *sock;
+	struct io_buffer *kbuf;
+	unsigned flags;
+	int min_ret = 0;
+	int ret, cflags = 0;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+
+	sock = sock_from_file(req->file);
+	if (unlikely(!sock))
+		return -ENOTSOCK;
+
+	kmsg = req->async_data;
+	if (!kmsg) {
+		ret = io_recvmsg_copy_hdr(req, &iomsg);
+		if (ret)
+			return ret;
+		kmsg = &iomsg;
+	}
+
+	if (req->flags & REQ_F_BUFFER_SELECT) {
+		kbuf = io_recv_buffer_select(req, !force_nonblock);
+		if (IS_ERR(kbuf))
+			return PTR_ERR(kbuf);
+		kmsg->fast_iov[0].iov_base = u64_to_user_ptr(kbuf->addr);
+		kmsg->fast_iov[0].iov_len = req->sr_msg.len;
+		iov_iter_init(&kmsg->msg.msg_iter, READ, kmsg->fast_iov,
+				1, req->sr_msg.len);
+	}
+
+	flags = req->sr_msg.msg_flags;
+	if (force_nonblock)
+		flags |= MSG_DONTWAIT;
+	if (flags & MSG_WAITALL && !kmsg->msg.msg_controllen)
+		min_ret = iov_iter_count(&kmsg->msg.msg_iter);
+
+	ret = __sys_recvmsg_sock(sock, &kmsg->msg, req->sr_msg.umsg,
+					kmsg->uaddr, flags);
+	if (ret < min_ret) {
+		if (ret == -EAGAIN && force_nonblock)
+			return io_setup_async_msg(req, kmsg);
+		if (ret == -ERESTARTSYS)
+			ret = -EINTR;
+		if (ret > 0 && io_net_retry(sock, flags)) {
+			sr->done_io += ret;
+			req->flags |= REQ_F_PARTIAL_IO;
+			return io_setup_async_msg(req, kmsg);
+		}
+		req_set_fail(req);
+	} else if ((flags & MSG_WAITALL) && (kmsg->msg.msg_flags & (MSG_TRUNC | MSG_CTRUNC))) {
+		req_set_fail(req);
+	}
+
+	if (req->flags & REQ_F_BUFFER_SELECTED)
+		cflags = io_put_recv_kbuf(req);
+	/* fast path, check for non-NULL to avoid function call */
+	if (kmsg->free_iov)
+		kfree(kmsg->free_iov);
+	req->flags &= ~REQ_F_NEED_CLEANUP;
+	if (ret >= 0)
+		ret += sr->done_io;
+	else if (sr->done_io)
+		ret = sr->done_io;
+	__io_req_complete(req, issue_flags, ret, cflags);
+	return 0;
+}
+
+static int io_recv(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_buffer *kbuf;
+	struct io_sr_msg *sr = &req->sr_msg;
+	struct msghdr msg;
+	void __user *buf = sr->buf;
+	struct socket *sock;
+	struct iovec iov;
+	unsigned flags;
+	int min_ret = 0;
+	int ret, cflags = 0;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+
+	sock = sock_from_file(req->file);
+	if (unlikely(!sock))
+		return -ENOTSOCK;
+
+	if (req->flags & REQ_F_BUFFER_SELECT) {
+		kbuf = io_recv_buffer_select(req, !force_nonblock);
+		if (IS_ERR(kbuf))
+			return PTR_ERR(kbuf);
+		buf = u64_to_user_ptr(kbuf->addr);
+	}
+
+	ret = import_single_range(READ, buf, sr->len, &iov, &msg.msg_iter);
+	if (unlikely(ret))
+		goto out_free;
+
+	msg.msg_name = NULL;
+	msg.msg_control = NULL;
+	msg.msg_controllen = 0;
+	msg.msg_namelen = 0;
+	msg.msg_iocb = NULL;
+	msg.msg_flags = 0;
+
+	flags = req->sr_msg.msg_flags;
+	if (force_nonblock)
+		flags |= MSG_DONTWAIT;
+	if (flags & MSG_WAITALL)
+		min_ret = iov_iter_count(&msg.msg_iter);
+
+	ret = sock_recvmsg(sock, &msg, flags);
+	if (ret < min_ret) {
+		if (ret == -EAGAIN && force_nonblock)
+			return -EAGAIN;
+		if (ret == -ERESTARTSYS)
+			ret = -EINTR;
+		if (ret > 0 && io_net_retry(sock, flags)) {
+			sr->len -= ret;
+			sr->buf += ret;
+			sr->done_io += ret;
+			req->flags |= REQ_F_PARTIAL_IO;
+			return -EAGAIN;
+		}
+		req_set_fail(req);
+	} else if ((flags & MSG_WAITALL) && (msg.msg_flags & (MSG_TRUNC | MSG_CTRUNC))) {
+out_free:
+		req_set_fail(req);
+	}
+	if (req->flags & REQ_F_BUFFER_SELECTED)
+		cflags = io_put_recv_kbuf(req);
+	if (ret >= 0)
+		ret += sr->done_io;
+	else if (sr->done_io)
+		ret = sr->done_io;
+	__io_req_complete(req, issue_flags, ret, cflags);
+	return 0;
+}
+
+static int io_accept_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_accept *accept = &req->accept;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->len || sqe->buf_index)
+		return -EINVAL;
+
+	accept->addr = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	accept->addr_len = u64_to_user_ptr(READ_ONCE(sqe->addr2));
+	accept->flags = READ_ONCE(sqe->accept_flags);
+	accept->nofile = rlimit(RLIMIT_NOFILE);
+
+	accept->file_slot = READ_ONCE(sqe->file_index);
+	if (accept->file_slot && (accept->flags & SOCK_CLOEXEC))
+		return -EINVAL;
+	if (accept->flags & ~(SOCK_CLOEXEC | SOCK_NONBLOCK))
+		return -EINVAL;
+	if (SOCK_NONBLOCK != O_NONBLOCK && (accept->flags & SOCK_NONBLOCK))
+		accept->flags = (accept->flags & ~SOCK_NONBLOCK) | O_NONBLOCK;
+	return 0;
+}
+
+static int io_accept(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_accept *accept = &req->accept;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+	unsigned int file_flags = force_nonblock ? O_NONBLOCK : 0;
+	bool fixed = !!accept->file_slot;
+	struct file *file;
+	int ret, fd;
+
+	if (!fixed) {
+		fd = __get_unused_fd_flags(accept->flags, accept->nofile);
+		if (unlikely(fd < 0))
+			return fd;
+	}
+	file = do_accept(req->file, file_flags, accept->addr, accept->addr_len,
+			 accept->flags);
+	if (IS_ERR(file)) {
+		if (!fixed)
+			put_unused_fd(fd);
+		ret = PTR_ERR(file);
+		/* safe to retry */
+		req->flags |= REQ_F_PARTIAL_IO;
+		if (ret == -EAGAIN && force_nonblock)
+			return -EAGAIN;
+		if (ret == -ERESTARTSYS)
+			ret = -EINTR;
+		req_set_fail(req);
+	} else if (!fixed) {
+		fd_install(fd, file);
+		ret = fd;
+	} else {
+		ret = io_install_fixed_file(req, file, issue_flags,
+					    accept->file_slot - 1);
+	}
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_connect_prep_async(struct io_kiocb *req)
+{
+	struct io_async_connect *io = req->async_data;
+	struct io_connect *conn = &req->connect;
+
+	return move_addr_to_kernel(conn->addr, conn->addr_len, &io->address);
+}
+
+static int io_connect_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_connect *conn = &req->connect;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->len || sqe->buf_index || sqe->rw_flags ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+
+	conn->addr = u64_to_user_ptr(READ_ONCE(sqe->addr));
+	conn->addr_len =  READ_ONCE(sqe->addr2);
+	return 0;
+}
+
+static int io_connect(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_async_connect __io, *io;
+	unsigned file_flags;
+	int ret;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+
+	if (req->async_data) {
+		io = req->async_data;
+	} else {
+		ret = move_addr_to_kernel(req->connect.addr,
+						req->connect.addr_len,
+						&__io.address);
+		if (ret)
+			goto out;
+		io = &__io;
+	}
+
+	file_flags = force_nonblock ? O_NONBLOCK : 0;
+
+	ret = __sys_connect_file(req->file, &io->address,
+					req->connect.addr_len, file_flags);
+	if ((ret == -EAGAIN || ret == -EINPROGRESS) && force_nonblock) {
+		if (req->async_data)
+			return -EAGAIN;
+		if (io_alloc_async_data(req)) {
+			ret = -ENOMEM;
+			goto out;
+		}
+		memcpy(req->async_data, &__io, sizeof(__io));
+		return -EAGAIN;
+	}
+	if (ret == -ERESTARTSYS)
+		ret = -EINTR;
+out:
+	if (ret < 0)
+		req_set_fail(req);
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+#else /* !CONFIG_NET */
+#define IO_NETOP_FN(op)							\
+static int io_##op(struct io_kiocb *req, unsigned int issue_flags)	\
+{									\
+	return -EOPNOTSUPP;						\
+}
+
+#define IO_NETOP_PREP(op)						\
+IO_NETOP_FN(op)								\
+static int io_##op##_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe) \
+{									\
+	return -EOPNOTSUPP;						\
+}									\
+
+#define IO_NETOP_PREP_ASYNC(op)						\
+IO_NETOP_PREP(op)							\
+static int io_##op##_prep_async(struct io_kiocb *req)			\
+{									\
+	return -EOPNOTSUPP;						\
+}
+
+IO_NETOP_PREP_ASYNC(sendmsg);
+IO_NETOP_PREP_ASYNC(recvmsg);
+IO_NETOP_PREP_ASYNC(connect);
+IO_NETOP_PREP(accept);
+IO_NETOP_FN(send);
+IO_NETOP_FN(recv);
+#endif /* CONFIG_NET */
+
+struct io_poll_table {
+	struct poll_table_struct pt;
+	struct io_kiocb *req;
+	int nr_entries;
+	int error;
+};
+
+#define IO_POLL_CANCEL_FLAG	BIT(31)
+#define IO_POLL_RETRY_FLAG	BIT(30)
+#define IO_POLL_REF_MASK	GENMASK(29, 0)
+
+/*
+ * We usually have 1-2 refs taken, 128 is more than enough and we want to
+ * maximise the margin between this amount and the moment when it overflows.
+ */
+#define IO_POLL_REF_BIAS       128
+
+static bool io_poll_get_ownership_slowpath(struct io_kiocb *req)
+{
+	int v;
+
+	/*
+	 * poll_refs are already elevated and we don't have much hope for
+	 * grabbing the ownership. Instead of incrementing set a retry flag
+	 * to notify the loop that there might have been some change.
+	 */
+	v = atomic_fetch_or(IO_POLL_RETRY_FLAG, &req->poll_refs);
+	if (v & IO_POLL_REF_MASK)
+		return false;
+	return !(atomic_fetch_inc(&req->poll_refs) & IO_POLL_REF_MASK);
+}
+
+/*
+ * If refs part of ->poll_refs (see IO_POLL_REF_MASK) is 0, it's free. We can
+ * bump it and acquire ownership. It's disallowed to modify requests while not
+ * owning it, that prevents from races for enqueueing task_work's and b/w
+ * arming poll and wakeups.
+ */
+static inline bool io_poll_get_ownership(struct io_kiocb *req)
+{
+	if (unlikely(atomic_read(&req->poll_refs) >= IO_POLL_REF_BIAS))
+		return io_poll_get_ownership_slowpath(req);
+	return !(atomic_fetch_inc(&req->poll_refs) & IO_POLL_REF_MASK);
+}
+
+static void io_poll_mark_cancelled(struct io_kiocb *req)
+{
+	atomic_or(IO_POLL_CANCEL_FLAG, &req->poll_refs);
+}
+
+static struct io_poll_iocb *io_poll_get_double(struct io_kiocb *req)
+{
+	/* pure poll stashes this in ->async_data, poll driven retry elsewhere */
+	if (req->opcode == IORING_OP_POLL_ADD)
+		return req->async_data;
+	return req->apoll->double_poll;
+}
+
+static struct io_poll_iocb *io_poll_get_single(struct io_kiocb *req)
+{
+	if (req->opcode == IORING_OP_POLL_ADD)
+		return &req->poll;
+	return &req->apoll->poll;
+}
+
+static void io_poll_req_insert(struct io_kiocb *req)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct hlist_head *list;
+
+	list = &ctx->cancel_hash[hash_long(req->user_data, ctx->cancel_hash_bits)];
+	hlist_add_head(&req->hash_node, list);
+}
+
+static void io_init_poll_iocb(struct io_poll_iocb *poll, __poll_t events,
+			      wait_queue_func_t wake_func)
+{
+	poll->head = NULL;
+#define IO_POLL_UNMASK	(EPOLLERR|EPOLLHUP|EPOLLNVAL|EPOLLRDHUP)
+	/* mask in events that we always want/need */
+	poll->events = events | IO_POLL_UNMASK;
+	INIT_LIST_HEAD(&poll->wait.entry);
+	init_waitqueue_func_entry(&poll->wait, wake_func);
+}
+
+static inline void io_poll_remove_entry(struct io_poll_iocb *poll)
+{
+	struct wait_queue_head *head = smp_load_acquire(&poll->head);
+
+	if (head) {
+		spin_lock_irq(&head->lock);
+		list_del_init(&poll->wait.entry);
+		poll->head = NULL;
+		spin_unlock_irq(&head->lock);
+	}
+}
+
+static void io_poll_remove_entries(struct io_kiocb *req)
+{
+	struct io_poll_iocb *poll = io_poll_get_single(req);
+	struct io_poll_iocb *poll_double = io_poll_get_double(req);
+
+	/*
+	 * While we hold the waitqueue lock and the waitqueue is nonempty,
+	 * wake_up_pollfree() will wait for us.  However, taking the waitqueue
+	 * lock in the first place can race with the waitqueue being freed.
+	 *
+	 * We solve this as eventpoll does: by taking advantage of the fact that
+	 * all users of wake_up_pollfree() will RCU-delay the actual free.  If
+	 * we enter rcu_read_lock() and see that the pointer to the queue is
+	 * non-NULL, we can then lock it without the memory being freed out from
+	 * under us.
+	 *
+	 * Keep holding rcu_read_lock() as long as we hold the queue lock, in
+	 * case the caller deletes the entry from the queue, leaving it empty.
+	 * In that case, only RCU prevents the queue memory from being freed.
+	 */
+	rcu_read_lock();
+	io_poll_remove_entry(poll);
+	if (poll_double)
+		io_poll_remove_entry(poll_double);
+	rcu_read_unlock();
+}
+
+/*
+ * All poll tw should go through this. Checks for poll events, manages
+ * references, does rewait, etc.
+ *
+ * Returns a negative error on failure. >0 when no action require, which is
+ * either spurious wakeup or multishot CQE is served. 0 when it's done with
+ * the request, then the mask is stored in req->result.
+ */
+static int io_poll_check_events(struct io_kiocb *req)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_poll_iocb *poll = io_poll_get_single(req);
+	int v;
+
+	/* req->task == current here, checking PF_EXITING is safe */
+	if (unlikely(req->task->flags & PF_EXITING))
+		io_poll_mark_cancelled(req);
+
+	do {
+		v = atomic_read(&req->poll_refs);
+
+		/* tw handler should be the owner, and so have some references */
+		if (WARN_ON_ONCE(!(v & IO_POLL_REF_MASK)))
+			return 0;
+		if (v & IO_POLL_CANCEL_FLAG)
+			return -ECANCELED;
+		/*
+		 * cqe.res contains only events of the first wake up
+		 * and all others are be lost. Redo vfs_poll() to get
+		 * up to date state.
+		 */
+		if ((v & IO_POLL_REF_MASK) != 1)
+			req->result = 0;
+		if (v & IO_POLL_RETRY_FLAG) {
+			req->result = 0;
+			/*
+			 * We won't find new events that came in between
+			 * vfs_poll and the ref put unless we clear the
+			 * flag in advance.
+			 */
+			atomic_andnot(IO_POLL_RETRY_FLAG, &req->poll_refs);
+			v &= ~IO_POLL_RETRY_FLAG;
+		}
+
+		if (!req->result) {
+			struct poll_table_struct pt = { ._key = poll->events };
+
+			req->result = vfs_poll(req->file, &pt) & poll->events;
+		}
+
+		/* multishot, just fill an CQE and proceed */
+		if (req->result && !(poll->events & EPOLLONESHOT)) {
+			__poll_t mask = mangle_poll(req->result & poll->events);
+			bool filled;
+
+			spin_lock(&ctx->completion_lock);
+			filled = io_fill_cqe_aux(ctx, req->user_data, mask,
+						 IORING_CQE_F_MORE);
+			io_commit_cqring(ctx);
+			spin_unlock(&ctx->completion_lock);
+			if (unlikely(!filled))
+				return -ECANCELED;
+			io_cqring_ev_posted(ctx);
+		} else if (req->result) {
+			return 0;
+		}
+
+		/* force the next iteration to vfs_poll() */
+		req->result = 0;
+
+		/*
+		 * Release all references, retry if someone tried to restart
+		 * task_work while we were executing it.
+		 */
+	} while (atomic_sub_return(v & IO_POLL_REF_MASK, &req->poll_refs) &
+					IO_POLL_REF_MASK);
+
+	return 1;
+}
+
+static void io_poll_task_func(struct io_kiocb *req, bool *locked)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	int ret;
+
+	ret = io_poll_check_events(req);
+	if (ret > 0)
+		return;
+
+	if (!ret) {
+		req->result = mangle_poll(req->result & req->poll.events);
+	} else {
+		req->result = ret;
+		req_set_fail(req);
+	}
+
+	io_poll_remove_entries(req);
+	spin_lock(&ctx->completion_lock);
+	hash_del(&req->hash_node);
+	spin_unlock(&ctx->completion_lock);
+	io_req_complete_post(req, req->result, 0);
+}
+
+static void io_apoll_task_func(struct io_kiocb *req, bool *locked)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	int ret;
+
+	ret = io_poll_check_events(req);
+	if (ret > 0)
+		return;
+
+	io_tw_lock(req->ctx, locked);
+	io_poll_remove_entries(req);
+	spin_lock(&ctx->completion_lock);
+	hash_del(&req->hash_node);
+	spin_unlock(&ctx->completion_lock);
+
+	if (!ret)
+		io_req_task_submit(req, locked);
+	else
+		io_req_complete_failed(req, ret);
+}
+
+static void __io_poll_execute(struct io_kiocb *req, int mask)
+{
+	req->result = mask;
+	if (req->opcode == IORING_OP_POLL_ADD)
+		req->io_task_work.func = io_poll_task_func;
+	else
+		req->io_task_work.func = io_apoll_task_func;
+
+	trace_io_uring_task_add(req->ctx, req->opcode, req->user_data, mask);
+	io_req_task_work_add(req);
+}
+
+static inline void io_poll_execute(struct io_kiocb *req, int res)
+{
+	if (io_poll_get_ownership(req))
+		__io_poll_execute(req, res);
+}
+
+static void io_poll_cancel_req(struct io_kiocb *req)
+{
+	io_poll_mark_cancelled(req);
+	/* kick tw, which should complete the request */
+	io_poll_execute(req, 0);
+}
+
+static int io_poll_wake(struct wait_queue_entry *wait, unsigned mode, int sync,
+			void *key)
+{
+	struct io_kiocb *req = wait->private;
+	struct io_poll_iocb *poll = container_of(wait, struct io_poll_iocb,
+						 wait);
+	__poll_t mask = key_to_poll(key);
+
+	if (unlikely(mask & POLLFREE)) {
+		io_poll_mark_cancelled(req);
+		/* we have to kick tw in case it's not already */
+		io_poll_execute(req, 0);
+
+		/*
+		 * If the waitqueue is being freed early but someone is already
+		 * holds ownership over it, we have to tear down the request as
+		 * best we can. That means immediately removing the request from
+		 * its waitqueue and preventing all further accesses to the
+		 * waitqueue via the request.
+		 */
+		list_del_init(&poll->wait.entry);
+
+		/*
+		 * Careful: this *must* be the last step, since as soon
+		 * as req->head is NULL'ed out, the request can be
+		 * completed and freed, since aio_poll_complete_work()
+		 * will no longer need to take the waitqueue lock.
+		 */
+		smp_store_release(&poll->head, NULL);
+		return 1;
+	}
+
+	/* for instances that support it check for an event match first */
+	if (mask && !(mask & poll->events))
+		return 0;
+
+	if (io_poll_get_ownership(req)) {
+		/*
+		 * If we trigger a multishot poll off our own wakeup path,
+		 * disable multishot as there is a circular dependency between
+		 * CQ posting and triggering the event.
+		 */
+		if (mask & EPOLL_URING_WAKE)
+			poll->events |= EPOLLONESHOT;
+
+		__io_poll_execute(req, mask);
+	}
+	return 1;
+}
+
+static void __io_queue_proc(struct io_poll_iocb *poll, struct io_poll_table *pt,
+			    struct wait_queue_head *head,
+			    struct io_poll_iocb **poll_ptr)
+{
+	struct io_kiocb *req = pt->req;
+
+	/*
+	 * The file being polled uses multiple waitqueues for poll handling
+	 * (e.g. one for read, one for write). Setup a separate io_poll_iocb
+	 * if this happens.
+	 */
+	if (unlikely(pt->nr_entries)) {
+		struct io_poll_iocb *first = poll;
+
+		/* double add on the same waitqueue head, ignore */
+		if (first->head == head)
+			return;
+		/* already have a 2nd entry, fail a third attempt */
+		if (*poll_ptr) {
+			if ((*poll_ptr)->head == head)
+				return;
+			pt->error = -EINVAL;
+			return;
+		}
+
+		poll = kmalloc(sizeof(*poll), GFP_ATOMIC);
+		if (!poll) {
+			pt->error = -ENOMEM;
+			return;
+		}
+		io_init_poll_iocb(poll, first->events, first->wait.func);
+		*poll_ptr = poll;
+	}
+
+	pt->nr_entries++;
+	poll->head = head;
+	poll->wait.private = req;
+
+	if (poll->events & EPOLLEXCLUSIVE)
+		add_wait_queue_exclusive(head, &poll->wait);
+	else
+		add_wait_queue(head, &poll->wait);
+}
+
+static void io_poll_queue_proc(struct file *file, struct wait_queue_head *head,
+			       struct poll_table_struct *p)
+{
+	struct io_poll_table *pt = container_of(p, struct io_poll_table, pt);
+
+	__io_queue_proc(&pt->req->poll, pt, head,
+			(struct io_poll_iocb **) &pt->req->async_data);
+}
+
+static int __io_arm_poll_handler(struct io_kiocb *req,
+				 struct io_poll_iocb *poll,
+				 struct io_poll_table *ipt, __poll_t mask)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	INIT_HLIST_NODE(&req->hash_node);
+	io_init_poll_iocb(poll, mask, io_poll_wake);
+	poll->file = req->file;
+	poll->wait.private = req;
+
+	ipt->pt._key = mask;
+	ipt->req = req;
+	ipt->error = 0;
+	ipt->nr_entries = 0;
+
+	/*
+	 * Take the ownership to delay any tw execution up until we're done
+	 * with poll arming. see io_poll_get_ownership().
+	 */
+	atomic_set(&req->poll_refs, 1);
+	mask = vfs_poll(req->file, &ipt->pt) & poll->events;
+
+	if (mask && (poll->events & EPOLLONESHOT)) {
+		io_poll_remove_entries(req);
+		/* no one else has access to the req, forget about the ref */
+		return mask;
+	}
+	if (!mask && unlikely(ipt->error || !ipt->nr_entries)) {
+		io_poll_remove_entries(req);
+		if (!ipt->error)
+			ipt->error = -EINVAL;
+		return 0;
+	}
+
+	spin_lock(&ctx->completion_lock);
+	io_poll_req_insert(req);
+	spin_unlock(&ctx->completion_lock);
+
+	if (mask) {
+		/* can't multishot if failed, just queue the event we've got */
+		if (unlikely(ipt->error || !ipt->nr_entries)) {
+			poll->events |= EPOLLONESHOT;
+			ipt->error = 0;
+		}
+		__io_poll_execute(req, mask);
+		return 0;
+	}
+
+	/*
+	 * Try to release ownership. If we see a change of state, e.g.
+	 * poll was waken up, queue up a tw, it'll deal with it.
+	 */
+	if (atomic_cmpxchg(&req->poll_refs, 1, 0) != 1)
+		__io_poll_execute(req, 0);
+	return 0;
+}
+
+static void io_async_queue_proc(struct file *file, struct wait_queue_head *head,
+			       struct poll_table_struct *p)
+{
+	struct io_poll_table *pt = container_of(p, struct io_poll_table, pt);
+	struct async_poll *apoll = pt->req->apoll;
+
+	__io_queue_proc(&apoll->poll, pt, head, &apoll->double_poll);
+}
+
+enum {
+	IO_APOLL_OK,
+	IO_APOLL_ABORTED,
+	IO_APOLL_READY
+};
+
+/*
+ * We can't reliably detect loops in repeated poll triggers and issue
+ * subsequently failing. But rather than fail these immediately, allow a
+ * certain amount of retries before we give up. Given that this condition
+ * should _rarely_ trigger even once, we should be fine with a larger value.
+ */
+#define APOLL_MAX_RETRY		128
+
+static int io_arm_poll_handler(struct io_kiocb *req)
+{
+	const struct io_op_def *def = &io_op_defs[req->opcode];
+	struct io_ring_ctx *ctx = req->ctx;
+	struct async_poll *apoll;
+	struct io_poll_table ipt;
+	__poll_t mask = EPOLLONESHOT | POLLERR | POLLPRI;
+	int ret;
+
+	if (!req->file || !file_can_poll(req->file))
+		return IO_APOLL_ABORTED;
+	if (!def->pollin && !def->pollout)
+		return IO_APOLL_ABORTED;
+
+	if (def->pollin) {
+		mask |= POLLIN | POLLRDNORM;
+
+		/* If reading from MSG_ERRQUEUE using recvmsg, ignore POLLIN */
+		if ((req->opcode == IORING_OP_RECVMSG) &&
+		    (req->sr_msg.msg_flags & MSG_ERRQUEUE))
+			mask &= ~POLLIN;
+	} else {
+		mask |= POLLOUT | POLLWRNORM;
+	}
+
+	if (req->flags & REQ_F_POLLED) {
+		apoll = req->apoll;
+		kfree(apoll->double_poll);
+		if (unlikely(!--apoll->poll.retries)) {
+			apoll->double_poll = NULL;
+			return IO_APOLL_ABORTED;
+		}
+	} else {
+		apoll = kmalloc(sizeof(*apoll), GFP_ATOMIC);
+		if (unlikely(!apoll))
+			return IO_APOLL_ABORTED;
+		apoll->poll.retries = APOLL_MAX_RETRY;
+	}
+	apoll->double_poll = NULL;
+	req->apoll = apoll;
+	req->flags |= REQ_F_POLLED;
+	ipt.pt._qproc = io_async_queue_proc;
+
+	ret = __io_arm_poll_handler(req, &apoll->poll, &ipt, mask);
+	if (ret || ipt.error)
+		return ret ? IO_APOLL_READY : IO_APOLL_ABORTED;
+
+	trace_io_uring_poll_arm(ctx, req, req->opcode, req->user_data,
+				mask, apoll->poll.events);
+	return IO_APOLL_OK;
+}
+
+/*
+ * Returns true if we found and killed one or more poll requests
+ */
+static bool io_poll_remove_all(struct io_ring_ctx *ctx, struct task_struct *tsk,
+			       bool cancel_all)
+{
+	struct hlist_node *tmp;
+	struct io_kiocb *req;
+	bool found = false;
+	int i;
+
+	spin_lock(&ctx->completion_lock);
+	for (i = 0; i < (1U << ctx->cancel_hash_bits); i++) {
+		struct hlist_head *list;
+
+		list = &ctx->cancel_hash[i];
+		hlist_for_each_entry_safe(req, tmp, list, hash_node) {
+			if (io_match_task_safe(req, tsk, cancel_all)) {
+				hlist_del_init(&req->hash_node);
+				io_poll_cancel_req(req);
+				found = true;
+			}
+		}
+	}
+	spin_unlock(&ctx->completion_lock);
+	return found;
+}
+
+static struct io_kiocb *io_poll_find(struct io_ring_ctx *ctx, __u64 sqe_addr,
+				     bool poll_only)
+	__must_hold(&ctx->completion_lock)
+{
+	struct hlist_head *list;
+	struct io_kiocb *req;
+
+	list = &ctx->cancel_hash[hash_long(sqe_addr, ctx->cancel_hash_bits)];
+	hlist_for_each_entry(req, list, hash_node) {
+		if (sqe_addr != req->user_data)
+			continue;
+		if (poll_only && req->opcode != IORING_OP_POLL_ADD)
+			continue;
+		return req;
+	}
+	return NULL;
+}
+
+static bool io_poll_disarm(struct io_kiocb *req)
+	__must_hold(&ctx->completion_lock)
+{
+	if (!io_poll_get_ownership(req))
+		return false;
+	io_poll_remove_entries(req);
+	hash_del(&req->hash_node);
+	return true;
+}
+
+static int io_poll_cancel(struct io_ring_ctx *ctx, __u64 sqe_addr,
+			  bool poll_only)
+	__must_hold(&ctx->completion_lock)
+{
+	struct io_kiocb *req = io_poll_find(ctx, sqe_addr, poll_only);
+
+	if (!req)
+		return -ENOENT;
+	io_poll_cancel_req(req);
+	return 0;
+}
+
+static __poll_t io_poll_parse_events(const struct io_uring_sqe *sqe,
+				     unsigned int flags)
+{
+	u32 events;
+
+	events = READ_ONCE(sqe->poll32_events);
+#ifdef __BIG_ENDIAN
+	events = swahw32(events);
+#endif
+	if (!(flags & IORING_POLL_ADD_MULTI))
+		events |= EPOLLONESHOT;
+	return demangle_poll(events) | (events & (EPOLLEXCLUSIVE|EPOLLONESHOT));
+}
+
+static int io_poll_update_prep(struct io_kiocb *req,
+			       const struct io_uring_sqe *sqe)
+{
+	struct io_poll_update *upd = &req->poll_update;
+	u32 flags;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->splice_fd_in)
+		return -EINVAL;
+	flags = READ_ONCE(sqe->len);
+	if (flags & ~(IORING_POLL_UPDATE_EVENTS | IORING_POLL_UPDATE_USER_DATA |
+		      IORING_POLL_ADD_MULTI))
+		return -EINVAL;
+	/* meaningless without update */
+	if (flags == IORING_POLL_ADD_MULTI)
+		return -EINVAL;
+
+	upd->old_user_data = READ_ONCE(sqe->addr);
+	upd->update_events = flags & IORING_POLL_UPDATE_EVENTS;
+	upd->update_user_data = flags & IORING_POLL_UPDATE_USER_DATA;
+
+	upd->new_user_data = READ_ONCE(sqe->off);
+	if (!upd->update_user_data && upd->new_user_data)
+		return -EINVAL;
+	if (upd->update_events)
+		upd->events = io_poll_parse_events(sqe, flags);
+	else if (sqe->poll32_events)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int io_poll_add_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	struct io_poll_iocb *poll = &req->poll;
+	u32 flags;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->off || sqe->addr)
+		return -EINVAL;
+	flags = READ_ONCE(sqe->len);
+	if (flags & ~IORING_POLL_ADD_MULTI)
+		return -EINVAL;
+
+	io_req_set_refcount(req);
+	poll->events = io_poll_parse_events(sqe, flags);
+	return 0;
+}
+
+static int io_poll_add(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_poll_iocb *poll = &req->poll;
+	struct io_poll_table ipt;
+	int ret;
+
+	ipt.pt._qproc = io_poll_queue_proc;
+
+	ret = __io_arm_poll_handler(req, &req->poll, &ipt, poll->events);
+	if (!ret && ipt.error)
+		req_set_fail(req);
+	ret = ret ?: ipt.error;
+	if (ret)
+		__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_poll_update(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_kiocb *preq;
+	int ret2, ret = 0;
+
+	io_ring_submit_lock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+
+	spin_lock(&ctx->completion_lock);
+	preq = io_poll_find(ctx, req->poll_update.old_user_data, true);
+	if (!preq || !io_poll_disarm(preq)) {
+		spin_unlock(&ctx->completion_lock);
+		ret = preq ? -EALREADY : -ENOENT;
+		goto out;
+	}
+	spin_unlock(&ctx->completion_lock);
+
+	if (req->poll_update.update_events || req->poll_update.update_user_data) {
+		/* only mask one event flags, keep behavior flags */
+		if (req->poll_update.update_events) {
+			preq->poll.events &= ~0xffff;
+			preq->poll.events |= req->poll_update.events & 0xffff;
+			preq->poll.events |= IO_POLL_UNMASK;
+		}
+		if (req->poll_update.update_user_data)
+			preq->user_data = req->poll_update.new_user_data;
+
+		ret2 = io_poll_add(preq, issue_flags);
+		/* successfully updated, don't complete poll request */
+		if (!ret2)
+			goto out;
+	}
+	req_set_fail(preq);
+	io_req_complete(preq, -ECANCELED);
+out:
+	if (ret < 0)
+		req_set_fail(req);
+	/* complete update request, we're done with it */
+	io_req_complete(req, ret);
+	io_ring_submit_unlock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+	return 0;
+}
+
+static void io_req_task_timeout(struct io_kiocb *req, bool *locked)
+{
+	req_set_fail(req);
+	io_req_complete_post(req, -ETIME, 0);
+}
+
+static enum hrtimer_restart io_timeout_fn(struct hrtimer *timer)
+{
+	struct io_timeout_data *data = container_of(timer,
+						struct io_timeout_data, timer);
+	struct io_kiocb *req = data->req;
+	struct io_ring_ctx *ctx = req->ctx;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ctx->timeout_lock, flags);
+	list_del_init(&req->timeout.list);
+	atomic_set(&req->ctx->cq_timeouts,
+		atomic_read(&req->ctx->cq_timeouts) + 1);
+	spin_unlock_irqrestore(&ctx->timeout_lock, flags);
+
+	req->io_task_work.func = io_req_task_timeout;
+	io_req_task_work_add(req);
+	return HRTIMER_NORESTART;
+}
+
+static struct io_kiocb *io_timeout_extract(struct io_ring_ctx *ctx,
+					   __u64 user_data)
+	__must_hold(&ctx->timeout_lock)
+{
+	struct io_timeout_data *io;
+	struct io_kiocb *req;
+	bool found = false;
+
+	list_for_each_entry(req, &ctx->timeout_list, timeout.list) {
+		found = user_data == req->user_data;
+		if (found)
+			break;
+	}
+	if (!found)
+		return ERR_PTR(-ENOENT);
+
+	io = req->async_data;
+	if (hrtimer_try_to_cancel(&io->timer) == -1)
+		return ERR_PTR(-EALREADY);
+	list_del_init(&req->timeout.list);
+	return req;
+}
+
+static int io_timeout_cancel(struct io_ring_ctx *ctx, __u64 user_data)
+	__must_hold(&ctx->completion_lock)
+	__must_hold(&ctx->timeout_lock)
+{
+	struct io_kiocb *req = io_timeout_extract(ctx, user_data);
+
+	if (IS_ERR(req))
+		return PTR_ERR(req);
+
+	req_set_fail(req);
+	io_fill_cqe_req(req, -ECANCELED, 0);
+	io_put_req_deferred(req);
+	return 0;
+}
+
+static clockid_t io_timeout_get_clock(struct io_timeout_data *data)
+{
+	switch (data->flags & IORING_TIMEOUT_CLOCK_MASK) {
+	case IORING_TIMEOUT_BOOTTIME:
+		return CLOCK_BOOTTIME;
+	case IORING_TIMEOUT_REALTIME:
+		return CLOCK_REALTIME;
+	default:
+		/* can't happen, vetted at prep time */
+		WARN_ON_ONCE(1);
+		fallthrough;
+	case 0:
+		return CLOCK_MONOTONIC;
+	}
+}
+
+static int io_linked_timeout_update(struct io_ring_ctx *ctx, __u64 user_data,
+				    struct timespec64 *ts, enum hrtimer_mode mode)
+	__must_hold(&ctx->timeout_lock)
+{
+	struct io_timeout_data *io;
+	struct io_kiocb *req;
+	bool found = false;
+
+	list_for_each_entry(req, &ctx->ltimeout_list, timeout.list) {
+		found = user_data == req->user_data;
+		if (found)
+			break;
+	}
+	if (!found)
+		return -ENOENT;
+
+	io = req->async_data;
+	if (hrtimer_try_to_cancel(&io->timer) == -1)
+		return -EALREADY;
+	hrtimer_init(&io->timer, io_timeout_get_clock(io), mode);
+	io->timer.function = io_link_timeout_fn;
+	hrtimer_start(&io->timer, timespec64_to_ktime(*ts), mode);
+	return 0;
+}
+
+static int io_timeout_update(struct io_ring_ctx *ctx, __u64 user_data,
+			     struct timespec64 *ts, enum hrtimer_mode mode)
+	__must_hold(&ctx->timeout_lock)
+{
+	struct io_kiocb *req = io_timeout_extract(ctx, user_data);
+	struct io_timeout_data *data;
+
+	if (IS_ERR(req))
+		return PTR_ERR(req);
+
+	req->timeout.off = 0; /* noseq */
+	data = req->async_data;
+	list_add_tail(&req->timeout.list, &ctx->timeout_list);
+	hrtimer_init(&data->timer, io_timeout_get_clock(data), mode);
+	data->timer.function = io_timeout_fn;
+	hrtimer_start(&data->timer, timespec64_to_ktime(*ts), mode);
+	return 0;
+}
+
+static int io_timeout_remove_prep(struct io_kiocb *req,
+				  const struct io_uring_sqe *sqe)
+{
+	struct io_timeout_rem *tr = &req->timeout_rem;
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(req->flags & (REQ_F_FIXED_FILE | REQ_F_BUFFER_SELECT)))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->len || sqe->splice_fd_in)
+		return -EINVAL;
+
+	tr->ltimeout = false;
+	tr->addr = READ_ONCE(sqe->addr);
+	tr->flags = READ_ONCE(sqe->timeout_flags);
+	if (tr->flags & IORING_TIMEOUT_UPDATE_MASK) {
+		if (hweight32(tr->flags & IORING_TIMEOUT_CLOCK_MASK) > 1)
+			return -EINVAL;
+		if (tr->flags & IORING_LINK_TIMEOUT_UPDATE)
+			tr->ltimeout = true;
+		if (tr->flags & ~(IORING_TIMEOUT_UPDATE_MASK|IORING_TIMEOUT_ABS))
+			return -EINVAL;
+		if (get_timespec64(&tr->ts, u64_to_user_ptr(sqe->addr2)))
+			return -EFAULT;
+	} else if (tr->flags) {
+		/* timeout removal doesn't support flags */
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static inline enum hrtimer_mode io_translate_timeout_mode(unsigned int flags)
+{
+	return (flags & IORING_TIMEOUT_ABS) ? HRTIMER_MODE_ABS
+					    : HRTIMER_MODE_REL;
+}
+
+/*
+ * Remove or update an existing timeout command
+ */
+static int io_timeout_remove(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_timeout_rem *tr = &req->timeout_rem;
+	struct io_ring_ctx *ctx = req->ctx;
+	int ret;
+
+	if (!(req->timeout_rem.flags & IORING_TIMEOUT_UPDATE)) {
+		spin_lock(&ctx->completion_lock);
+		spin_lock_irq(&ctx->timeout_lock);
+		ret = io_timeout_cancel(ctx, tr->addr);
+		spin_unlock_irq(&ctx->timeout_lock);
+		spin_unlock(&ctx->completion_lock);
+	} else {
+		enum hrtimer_mode mode = io_translate_timeout_mode(tr->flags);
+
+		spin_lock_irq(&ctx->timeout_lock);
+		if (tr->ltimeout)
+			ret = io_linked_timeout_update(ctx, tr->addr, &tr->ts, mode);
+		else
+			ret = io_timeout_update(ctx, tr->addr, &tr->ts, mode);
+		spin_unlock_irq(&ctx->timeout_lock);
+	}
+
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete_post(req, ret, 0);
+	return 0;
+}
+
+static int io_timeout_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe,
+			   bool is_timeout_link)
+{
+	struct io_timeout_data *data;
+	unsigned flags;
+	u32 off = READ_ONCE(sqe->off);
+
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->buf_index || sqe->len != 1 ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+	if (off && is_timeout_link)
+		return -EINVAL;
+	flags = READ_ONCE(sqe->timeout_flags);
+	if (flags & ~(IORING_TIMEOUT_ABS | IORING_TIMEOUT_CLOCK_MASK))
+		return -EINVAL;
+	/* more than one clock specified is invalid, obviously */
+	if (hweight32(flags & IORING_TIMEOUT_CLOCK_MASK) > 1)
+		return -EINVAL;
+
+	INIT_LIST_HEAD(&req->timeout.list);
+	req->timeout.off = off;
+	if (unlikely(off && !req->ctx->off_timeout_used))
+		req->ctx->off_timeout_used = true;
+
+	if (!req->async_data && io_alloc_async_data(req))
+		return -ENOMEM;
+
+	data = req->async_data;
+	data->req = req;
+	data->flags = flags;
+
+	if (get_timespec64(&data->ts, u64_to_user_ptr(sqe->addr)))
+		return -EFAULT;
+
+	INIT_LIST_HEAD(&req->timeout.list);
+	data->mode = io_translate_timeout_mode(flags);
+	hrtimer_init(&data->timer, io_timeout_get_clock(data), data->mode);
+
+	if (is_timeout_link) {
+		struct io_submit_link *link = &req->ctx->submit_state.link;
+
+		if (!link->head)
+			return -EINVAL;
+		if (link->last->opcode == IORING_OP_LINK_TIMEOUT)
+			return -EINVAL;
+		req->timeout.head = link->last;
+		link->last->flags |= REQ_F_ARM_LTIMEOUT;
+	}
+	return 0;
+}
+
+static int io_timeout(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_timeout_data *data = req->async_data;
+	struct list_head *entry;
+	u32 tail, off = req->timeout.off;
+
+	spin_lock_irq(&ctx->timeout_lock);
+
+	/*
+	 * sqe->off holds how many events that need to occur for this
+	 * timeout event to be satisfied. If it isn't set, then this is
+	 * a pure timeout request, sequence isn't used.
+	 */
+	if (io_is_timeout_noseq(req)) {
+		entry = ctx->timeout_list.prev;
+		goto add;
+	}
+
+	tail = ctx->cached_cq_tail - atomic_read(&ctx->cq_timeouts);
+	req->timeout.target_seq = tail + off;
+
+	/* Update the last seq here in case io_flush_timeouts() hasn't.
+	 * This is safe because ->completion_lock is held, and submissions
+	 * and completions are never mixed in the same ->completion_lock section.
+	 */
+	ctx->cq_last_tm_flush = tail;
+
+	/*
+	 * Insertion sort, ensuring the first entry in the list is always
+	 * the one we need first.
+	 */
+	list_for_each_prev(entry, &ctx->timeout_list) {
+		struct io_kiocb *nxt = list_entry(entry, struct io_kiocb,
+						  timeout.list);
+
+		if (io_is_timeout_noseq(nxt))
+			continue;
+		/* nxt.seq is behind @tail, otherwise would've been completed */
+		if (off >= nxt->timeout.target_seq - tail)
+			break;
+	}
+add:
+	list_add(&req->timeout.list, entry);
+	data->timer.function = io_timeout_fn;
+	hrtimer_start(&data->timer, timespec64_to_ktime(data->ts), data->mode);
+	spin_unlock_irq(&ctx->timeout_lock);
+	return 0;
+}
+
+struct io_cancel_data {
+	struct io_ring_ctx *ctx;
+	u64 user_data;
+};
+
+static bool io_cancel_cb(struct io_wq_work *work, void *data)
+{
+	struct io_kiocb *req = container_of(work, struct io_kiocb, work);
+	struct io_cancel_data *cd = data;
+
+	return req->ctx == cd->ctx && req->user_data == cd->user_data;
+}
+
+static int io_async_cancel_one(struct io_uring_task *tctx, u64 user_data,
+			       struct io_ring_ctx *ctx)
+{
+	struct io_cancel_data data = { .ctx = ctx, .user_data = user_data, };
+	enum io_wq_cancel cancel_ret;
+	int ret = 0;
+
+	if (!tctx || !tctx->io_wq)
+		return -ENOENT;
+
+	cancel_ret = io_wq_cancel_cb(tctx->io_wq, io_cancel_cb, &data, false);
+	switch (cancel_ret) {
+	case IO_WQ_CANCEL_OK:
+		ret = 0;
+		break;
+	case IO_WQ_CANCEL_RUNNING:
+		ret = -EALREADY;
+		break;
+	case IO_WQ_CANCEL_NOTFOUND:
+		ret = -ENOENT;
+		break;
+	}
+
+	return ret;
+}
+
+static int io_try_cancel_userdata(struct io_kiocb *req, u64 sqe_addr)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	int ret;
+
+	WARN_ON_ONCE(!io_wq_current_is_worker() && req->task != current);
+
+	ret = io_async_cancel_one(req->task->io_uring, sqe_addr, ctx);
+	if (ret != -ENOENT)
+		return ret;
+
+	spin_lock(&ctx->completion_lock);
+	spin_lock_irq(&ctx->timeout_lock);
+	ret = io_timeout_cancel(ctx, sqe_addr);
+	spin_unlock_irq(&ctx->timeout_lock);
+	if (ret != -ENOENT)
+		goto out;
+	ret = io_poll_cancel(ctx, sqe_addr, false);
+out:
+	spin_unlock(&ctx->completion_lock);
+	return ret;
+}
+
+static int io_async_cancel_prep(struct io_kiocb *req,
+				const struct io_uring_sqe *sqe)
+{
+	if (unlikely(req->ctx->flags & IORING_SETUP_IOPOLL))
+		return -EINVAL;
+	if (unlikely(req->flags & (REQ_F_FIXED_FILE | REQ_F_BUFFER_SELECT)))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->off || sqe->len || sqe->cancel_flags ||
+	    sqe->splice_fd_in)
+		return -EINVAL;
+
+	req->cancel.addr = READ_ONCE(sqe->addr);
+	return 0;
+}
+
+static int io_async_cancel(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	u64 sqe_addr = req->cancel.addr;
+	struct io_tctx_node *node;
+	int ret;
+
+	ret = io_try_cancel_userdata(req, sqe_addr);
+	if (ret != -ENOENT)
+		goto done;
+
+	/* slow path, try all io-wq's */
+	io_ring_submit_lock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+	ret = -ENOENT;
+	list_for_each_entry(node, &ctx->tctx_list, ctx_node) {
+		struct io_uring_task *tctx = node->task->io_uring;
+
+		ret = io_async_cancel_one(tctx, req->cancel.addr, ctx);
+		if (ret != -ENOENT)
+			break;
+	}
+	io_ring_submit_unlock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+done:
+	if (ret < 0)
+		req_set_fail(req);
+	io_req_complete_post(req, ret, 0);
+	return 0;
+}
+
+static int io_rsrc_update_prep(struct io_kiocb *req,
+				const struct io_uring_sqe *sqe)
+{
+	if (unlikely(req->flags & (REQ_F_FIXED_FILE | REQ_F_BUFFER_SELECT)))
+		return -EINVAL;
+	if (sqe->ioprio || sqe->rw_flags || sqe->splice_fd_in)
+		return -EINVAL;
+
+	req->rsrc_update.offset = READ_ONCE(sqe->off);
+	req->rsrc_update.nr_args = READ_ONCE(sqe->len);
+	if (!req->rsrc_update.nr_args)
+		return -EINVAL;
+	req->rsrc_update.arg = READ_ONCE(sqe->addr);
+	return 0;
+}
+
+static int io_files_update(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_uring_rsrc_update2 up;
+	int ret;
+
+	up.offset = req->rsrc_update.offset;
+	up.data = req->rsrc_update.arg;
+	up.nr = 0;
+	up.tags = 0;
+	up.resv = 0;
+	up.resv2 = 0;
+
+	io_ring_submit_lock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+	ret = __io_register_rsrc_update(ctx, IORING_RSRC_FILE,
+					&up, req->rsrc_update.nr_args);
+	io_ring_submit_unlock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+
+	if (ret < 0)
+		req_set_fail(req);
+	__io_req_complete(req, issue_flags, ret, 0);
+	return 0;
+}
+
+static int io_req_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe)
+{
+	switch (req->opcode) {
+	case IORING_OP_NOP:
+		if (READ_ONCE(sqe->rw_flags))
+			return -EINVAL;
+		return 0;
+	case IORING_OP_READV:
+	case IORING_OP_READ_FIXED:
+	case IORING_OP_READ:
+		return io_read_prep(req, sqe);
+	case IORING_OP_WRITEV:
+	case IORING_OP_WRITE_FIXED:
+	case IORING_OP_WRITE:
+		return io_write_prep(req, sqe);
+	case IORING_OP_POLL_ADD:
+		return io_poll_add_prep(req, sqe);
+	case IORING_OP_POLL_REMOVE:
+		return io_poll_update_prep(req, sqe);
+	case IORING_OP_FSYNC:
+		return io_fsync_prep(req, sqe);
+	case IORING_OP_SYNC_FILE_RANGE:
+		return io_sfr_prep(req, sqe);
+	case IORING_OP_SENDMSG:
+	case IORING_OP_SEND:
+		return io_sendmsg_prep(req, sqe);
+	case IORING_OP_RECVMSG:
+	case IORING_OP_RECV:
+		return io_recvmsg_prep(req, sqe);
+	case IORING_OP_CONNECT:
+		return io_connect_prep(req, sqe);
+	case IORING_OP_TIMEOUT:
+		return io_timeout_prep(req, sqe, false);
+	case IORING_OP_TIMEOUT_REMOVE:
+		return io_timeout_remove_prep(req, sqe);
+	case IORING_OP_ASYNC_CANCEL:
+		return io_async_cancel_prep(req, sqe);
+	case IORING_OP_LINK_TIMEOUT:
+		return io_timeout_prep(req, sqe, true);
+	case IORING_OP_ACCEPT:
+		return io_accept_prep(req, sqe);
+	case IORING_OP_FALLOCATE:
+		return io_fallocate_prep(req, sqe);
+	case IORING_OP_OPENAT:
+		return io_openat_prep(req, sqe);
+	case IORING_OP_CLOSE:
+		return io_close_prep(req, sqe);
+	case IORING_OP_FILES_UPDATE:
+		return io_rsrc_update_prep(req, sqe);
+	case IORING_OP_STATX:
+		return io_statx_prep(req, sqe);
+	case IORING_OP_FADVISE:
+		return io_fadvise_prep(req, sqe);
+	case IORING_OP_MADVISE:
+		return io_madvise_prep(req, sqe);
+	case IORING_OP_OPENAT2:
+		return io_openat2_prep(req, sqe);
+	case IORING_OP_EPOLL_CTL:
+		return io_epoll_ctl_prep(req, sqe);
+	case IORING_OP_SPLICE:
+		return io_splice_prep(req, sqe);
+	case IORING_OP_PROVIDE_BUFFERS:
+		return io_provide_buffers_prep(req, sqe);
+	case IORING_OP_REMOVE_BUFFERS:
+		return io_remove_buffers_prep(req, sqe);
+	case IORING_OP_TEE:
+		return io_tee_prep(req, sqe);
+	case IORING_OP_SHUTDOWN:
+		return io_shutdown_prep(req, sqe);
+	case IORING_OP_RENAMEAT:
+		return io_renameat_prep(req, sqe);
+	case IORING_OP_UNLINKAT:
+		return io_unlinkat_prep(req, sqe);
+	case IORING_OP_MKDIRAT:
+		return io_mkdirat_prep(req, sqe);
+	case IORING_OP_SYMLINKAT:
+		return io_symlinkat_prep(req, sqe);
+	case IORING_OP_LINKAT:
+		return io_linkat_prep(req, sqe);
+	}
+
+	printk_once(KERN_WARNING "io_uring: unhandled opcode %d\n",
+			req->opcode);
+	return -EINVAL;
+}
+
+static int io_req_prep_async(struct io_kiocb *req)
+{
+	if (!io_op_defs[req->opcode].needs_async_setup)
+		return 0;
+	if (WARN_ON_ONCE(req->async_data))
+		return -EFAULT;
+	if (io_alloc_async_data(req))
+		return -EAGAIN;
+
+	switch (req->opcode) {
+	case IORING_OP_READV:
+		return io_rw_prep_async(req, READ);
+	case IORING_OP_WRITEV:
+		return io_rw_prep_async(req, WRITE);
+	case IORING_OP_SENDMSG:
+		return io_sendmsg_prep_async(req);
+	case IORING_OP_RECVMSG:
+		return io_recvmsg_prep_async(req);
+	case IORING_OP_CONNECT:
+		return io_connect_prep_async(req);
+	}
+	printk_once(KERN_WARNING "io_uring: prep_async() bad opcode %d\n",
+		    req->opcode);
+	return -EFAULT;
+}
+
+static u32 io_get_sequence(struct io_kiocb *req)
+{
+	u32 seq = req->ctx->cached_sq_head;
+
+	/* need original cached_sq_head, but it was increased for each req */
+	io_for_each_link(req, req)
+		seq--;
+	return seq;
+}
+
+static bool io_drain_req(struct io_kiocb *req)
+{
+	struct io_kiocb *pos;
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_defer_entry *de;
+	int ret;
+	u32 seq;
+
+	if (req->flags & REQ_F_FAIL) {
+		io_req_complete_fail_submit(req);
+		return true;
+	}
+
+	/*
+	 * If we need to drain a request in the middle of a link, drain the
+	 * head request and the next request/link after the current link.
+	 * Considering sequential execution of links, IOSQE_IO_DRAIN will be
+	 * maintained for every request of our link.
+	 */
+	if (ctx->drain_next) {
+		req->flags |= REQ_F_IO_DRAIN;
+		ctx->drain_next = false;
+	}
+	/* not interested in head, start from the first linked */
+	io_for_each_link(pos, req->link) {
+		if (pos->flags & REQ_F_IO_DRAIN) {
+			ctx->drain_next = true;
+			req->flags |= REQ_F_IO_DRAIN;
+			break;
+		}
+	}
+
+	/* Still need defer if there is pending req in defer list. */
+	spin_lock(&ctx->completion_lock);
+	if (likely(list_empty_careful(&ctx->defer_list) &&
+		!(req->flags & REQ_F_IO_DRAIN))) {
+		spin_unlock(&ctx->completion_lock);
+		ctx->drain_active = false;
+		return false;
+	}
+	spin_unlock(&ctx->completion_lock);
+
+	seq = io_get_sequence(req);
+	/* Still a chance to pass the sequence check */
+	if (!req_need_defer(req, seq) && list_empty_careful(&ctx->defer_list))
+		return false;
+
+	ret = io_req_prep_async(req);
+	if (ret)
+		goto fail;
+	io_prep_async_link(req);
+	de = kmalloc(sizeof(*de), GFP_KERNEL);
+	if (!de) {
+		ret = -ENOMEM;
+fail:
+		io_req_complete_failed(req, ret);
+		return true;
+	}
+
+	spin_lock(&ctx->completion_lock);
+	if (!req_need_defer(req, seq) && list_empty(&ctx->defer_list)) {
+		spin_unlock(&ctx->completion_lock);
+		kfree(de);
+		io_queue_async_work(req, NULL);
+		return true;
+	}
+
+	trace_io_uring_defer(ctx, req, req->user_data);
+	de->req = req;
+	de->seq = seq;
+	list_add_tail(&de->list, &ctx->defer_list);
+	spin_unlock(&ctx->completion_lock);
+	return true;
+}
+
+static void io_clean_op(struct io_kiocb *req)
+{
+	if (req->flags & REQ_F_BUFFER_SELECTED) {
+		switch (req->opcode) {
+		case IORING_OP_READV:
+		case IORING_OP_READ_FIXED:
+		case IORING_OP_READ:
+			kfree((void *)(unsigned long)req->rw.addr);
+			break;
+		case IORING_OP_RECVMSG:
+		case IORING_OP_RECV:
+			kfree(req->sr_msg.kbuf);
+			break;
+		}
+	}
+
+	if (req->flags & REQ_F_NEED_CLEANUP) {
+		switch (req->opcode) {
+		case IORING_OP_READV:
+		case IORING_OP_READ_FIXED:
+		case IORING_OP_READ:
+		case IORING_OP_WRITEV:
+		case IORING_OP_WRITE_FIXED:
+		case IORING_OP_WRITE: {
+			struct io_async_rw *io = req->async_data;
+
+			kfree(io->free_iovec);
+			break;
+			}
+		case IORING_OP_RECVMSG:
+		case IORING_OP_SENDMSG: {
+			struct io_async_msghdr *io = req->async_data;
+
+			kfree(io->free_iov);
+			break;
+			}
+		case IORING_OP_OPENAT:
+		case IORING_OP_OPENAT2:
+			if (req->open.filename)
+				putname(req->open.filename);
+			break;
+		case IORING_OP_RENAMEAT:
+			putname(req->rename.oldpath);
+			putname(req->rename.newpath);
+			break;
+		case IORING_OP_UNLINKAT:
+			putname(req->unlink.filename);
+			break;
+		case IORING_OP_MKDIRAT:
+			putname(req->mkdir.filename);
+			break;
+		case IORING_OP_SYMLINKAT:
+			putname(req->symlink.oldpath);
+			putname(req->symlink.newpath);
+			break;
+		case IORING_OP_LINKAT:
+			putname(req->hardlink.oldpath);
+			putname(req->hardlink.newpath);
+			break;
+		}
+	}
+	if ((req->flags & REQ_F_POLLED) && req->apoll) {
+		kfree(req->apoll->double_poll);
+		kfree(req->apoll);
+		req->apoll = NULL;
+	}
+	if (req->flags & REQ_F_INFLIGHT) {
+		struct io_uring_task *tctx = req->task->io_uring;
+
+		atomic_dec(&tctx->inflight_tracked);
+	}
+	if (req->flags & REQ_F_CREDS)
+		put_cred(req->creds);
+
+	req->flags &= ~IO_REQ_CLEAN_FLAGS;
+}
+
+static int io_issue_sqe(struct io_kiocb *req, unsigned int issue_flags)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	const struct cred *creds = NULL;
+	int ret;
+
+	if ((req->flags & REQ_F_CREDS) && req->creds != current_cred())
+		creds = override_creds(req->creds);
+
+	switch (req->opcode) {
+	case IORING_OP_NOP:
+		ret = io_nop(req, issue_flags);
+		break;
+	case IORING_OP_READV:
+	case IORING_OP_READ_FIXED:
+	case IORING_OP_READ:
+		ret = io_read(req, issue_flags);
+		break;
+	case IORING_OP_WRITEV:
+	case IORING_OP_WRITE_FIXED:
+	case IORING_OP_WRITE:
+		ret = io_write(req, issue_flags);
+		break;
+	case IORING_OP_FSYNC:
+		ret = io_fsync(req, issue_flags);
+		break;
+	case IORING_OP_POLL_ADD:
+		ret = io_poll_add(req, issue_flags);
+		break;
+	case IORING_OP_POLL_REMOVE:
+		ret = io_poll_update(req, issue_flags);
+		break;
+	case IORING_OP_SYNC_FILE_RANGE:
+		ret = io_sync_file_range(req, issue_flags);
+		break;
+	case IORING_OP_SENDMSG:
+		ret = io_sendmsg(req, issue_flags);
+		break;
+	case IORING_OP_SEND:
+		ret = io_send(req, issue_flags);
+		break;
+	case IORING_OP_RECVMSG:
+		ret = io_recvmsg(req, issue_flags);
+		break;
+	case IORING_OP_RECV:
+		ret = io_recv(req, issue_flags);
+		break;
+	case IORING_OP_TIMEOUT:
+		ret = io_timeout(req, issue_flags);
+		break;
+	case IORING_OP_TIMEOUT_REMOVE:
+		ret = io_timeout_remove(req, issue_flags);
+		break;
+	case IORING_OP_ACCEPT:
+		ret = io_accept(req, issue_flags);
+		break;
+	case IORING_OP_CONNECT:
+		ret = io_connect(req, issue_flags);
+		break;
+	case IORING_OP_ASYNC_CANCEL:
+		ret = io_async_cancel(req, issue_flags);
+		break;
+	case IORING_OP_FALLOCATE:
+		ret = io_fallocate(req, issue_flags);
+		break;
+	case IORING_OP_OPENAT:
+		ret = io_openat(req, issue_flags);
+		break;
+	case IORING_OP_CLOSE:
+		ret = io_close(req, issue_flags);
+		break;
+	case IORING_OP_FILES_UPDATE:
+		ret = io_files_update(req, issue_flags);
+		break;
+	case IORING_OP_STATX:
+		ret = io_statx(req, issue_flags);
+		break;
+	case IORING_OP_FADVISE:
+		ret = io_fadvise(req, issue_flags);
+		break;
+	case IORING_OP_MADVISE:
+		ret = io_madvise(req, issue_flags);
+		break;
+	case IORING_OP_OPENAT2:
+		ret = io_openat2(req, issue_flags);
+		break;
+	case IORING_OP_EPOLL_CTL:
+		ret = io_epoll_ctl(req, issue_flags);
+		break;
+	case IORING_OP_SPLICE:
+		ret = io_splice(req, issue_flags);
+		break;
+	case IORING_OP_PROVIDE_BUFFERS:
+		ret = io_provide_buffers(req, issue_flags);
+		break;
+	case IORING_OP_REMOVE_BUFFERS:
+		ret = io_remove_buffers(req, issue_flags);
+		break;
+	case IORING_OP_TEE:
+		ret = io_tee(req, issue_flags);
+		break;
+	case IORING_OP_SHUTDOWN:
+		ret = io_shutdown(req, issue_flags);
+		break;
+	case IORING_OP_RENAMEAT:
+		ret = io_renameat(req, issue_flags);
+		break;
+	case IORING_OP_UNLINKAT:
+		ret = io_unlinkat(req, issue_flags);
+		break;
+	case IORING_OP_MKDIRAT:
+		ret = io_mkdirat(req, issue_flags);
+		break;
+	case IORING_OP_SYMLINKAT:
+		ret = io_symlinkat(req, issue_flags);
+		break;
+	case IORING_OP_LINKAT:
+		ret = io_linkat(req, issue_flags);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	if (creds)
+		revert_creds(creds);
+	if (ret)
+		return ret;
+	/* If the op doesn't have a file, we're not polling for it */
+	if ((ctx->flags & IORING_SETUP_IOPOLL) && req->file)
+		io_iopoll_req_issued(req);
+
+	return 0;
+}
+
+static struct io_wq_work *io_wq_free_work(struct io_wq_work *work)
+{
+	struct io_kiocb *req = container_of(work, struct io_kiocb, work);
+
+	req = io_put_req_find_next(req);
+	return req ? &req->work : NULL;
+}
+
+static void io_wq_submit_work(struct io_wq_work *work)
+{
+	struct io_kiocb *req = container_of(work, struct io_kiocb, work);
+	struct io_kiocb *timeout;
+	int ret = 0;
+
+	/* one will be dropped by ->io_free_work() after returning to io-wq */
+	if (!(req->flags & REQ_F_REFCOUNT))
+		__io_req_set_refcount(req, 2);
+	else
+		req_ref_get(req);
+
+	timeout = io_prep_linked_timeout(req);
+	if (timeout)
+		io_queue_linked_timeout(timeout);
+
+	/* either cancelled or io-wq is dying, so don't touch tctx->iowq */
+	if (work->flags & IO_WQ_WORK_CANCEL)
+		ret = -ECANCELED;
+
+	if (!ret) {
+		do {
+			ret = io_issue_sqe(req, 0);
+			/*
+			 * We can get EAGAIN for polled IO even though we're
+			 * forcing a sync submission from here, since we can't
+			 * wait for request slots on the block side.
+			 */
+			if (ret != -EAGAIN || !(req->ctx->flags & IORING_SETUP_IOPOLL))
+				break;
+			if (io_wq_worker_stopped())
+				break;
+			/*
+			 * If REQ_F_NOWAIT is set, then don't wait or retry with
+			 * poll. -EAGAIN is final for that case.
+			 */
+			if (req->flags & REQ_F_NOWAIT)
+				break;
+
+			cond_resched();
+		} while (1);
+	}
+
+	/* avoid locking problems by failing it from a clean context */
+	if (ret)
+		io_req_task_queue_fail(req, ret);
+}
+
+static inline struct io_fixed_file *io_fixed_file_slot(struct io_file_table *table,
+						       unsigned i)
+{
+	return &table->files[i];
+}
+
+static inline struct file *io_file_from_index(struct io_ring_ctx *ctx,
+					      int index)
+{
+	struct io_fixed_file *slot = io_fixed_file_slot(&ctx->file_table, index);
+
+	return (struct file *) (slot->file_ptr & FFS_MASK);
+}
+
+static void io_fixed_file_set(struct io_fixed_file *file_slot, struct file *file)
+{
+	unsigned long file_ptr = (unsigned long) file;
+
+	if (__io_file_supports_nowait(file, READ))
+		file_ptr |= FFS_ASYNC_READ;
+	if (__io_file_supports_nowait(file, WRITE))
+		file_ptr |= FFS_ASYNC_WRITE;
+	if (S_ISREG(file_inode(file)->i_mode))
+		file_ptr |= FFS_ISREG;
+	file_slot->file_ptr = file_ptr;
+}
+
+static inline struct file *io_file_get_fixed(struct io_ring_ctx *ctx,
+					     struct io_kiocb *req, int fd,
+					     unsigned int issue_flags)
+{
+	struct file *file = NULL;
+	unsigned long file_ptr;
+
+	io_ring_submit_lock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+
+	if (unlikely((unsigned int)fd >= ctx->nr_user_files))
+		goto out;
+	fd = array_index_nospec(fd, ctx->nr_user_files);
+	file_ptr = io_fixed_file_slot(&ctx->file_table, fd)->file_ptr;
+	file = (struct file *) (file_ptr & FFS_MASK);
+	file_ptr &= ~FFS_MASK;
+	/* mask in overlapping REQ_F and FFS bits */
+	req->flags |= (file_ptr << REQ_F_NOWAIT_READ_BIT);
+	io_req_set_rsrc_node(req);
+out:
+	io_ring_submit_unlock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+	return file;
+}
+
+static struct file *io_file_get_normal(struct io_ring_ctx *ctx,
+				       struct io_kiocb *req, int fd)
+{
+	struct file *file = fget(fd);
+
+	trace_io_uring_file_get(ctx, fd);
+
+	/* we don't allow fixed io_uring files */
+	if (file && unlikely(file->f_op == &io_uring_fops))
+		io_req_track_inflight(req);
+	return file;
+}
+
+static inline struct file *io_file_get(struct io_ring_ctx *ctx,
+				       struct io_kiocb *req, int fd, bool fixed,
+				       unsigned int issue_flags)
+{
+	if (fixed)
+		return io_file_get_fixed(ctx, req, fd, issue_flags);
+	else
+		return io_file_get_normal(ctx, req, fd);
+}
+
+static void io_req_task_link_timeout(struct io_kiocb *req, bool *locked)
+{
+	struct io_kiocb *prev = req->timeout.prev;
+	int ret = -ENOENT;
+
+	if (prev) {
+		if (!(req->task->flags & PF_EXITING))
+			ret = io_try_cancel_userdata(req, prev->user_data);
+		io_req_complete_post(req, ret ?: -ETIME, 0);
+		io_put_req(prev);
+	} else {
+		io_req_complete_post(req, -ETIME, 0);
+	}
+}
+
+static enum hrtimer_restart io_link_timeout_fn(struct hrtimer *timer)
+{
+	struct io_timeout_data *data = container_of(timer,
+						struct io_timeout_data, timer);
+	struct io_kiocb *prev, *req = data->req;
+	struct io_ring_ctx *ctx = req->ctx;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ctx->timeout_lock, flags);
+	prev = req->timeout.head;
+	req->timeout.head = NULL;
+
+	/*
+	 * We don't expect the list to be empty, that will only happen if we
+	 * race with the completion of the linked work.
+	 */
+	if (prev) {
+		io_remove_next_linked(prev);
+		if (!req_ref_inc_not_zero(prev))
+			prev = NULL;
+	}
+	list_del(&req->timeout.list);
+	req->timeout.prev = prev;
+	spin_unlock_irqrestore(&ctx->timeout_lock, flags);
+
+	req->io_task_work.func = io_req_task_link_timeout;
+	io_req_task_work_add(req);
+	return HRTIMER_NORESTART;
+}
+
+static void io_queue_linked_timeout(struct io_kiocb *req)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+
+	spin_lock_irq(&ctx->timeout_lock);
+	/*
+	 * If the back reference is NULL, then our linked request finished
+	 * before we got a chance to setup the timer
+	 */
+	if (req->timeout.head) {
+		struct io_timeout_data *data = req->async_data;
+
+		data->timer.function = io_link_timeout_fn;
+		hrtimer_start(&data->timer, timespec64_to_ktime(data->ts),
+				data->mode);
+		list_add_tail(&req->timeout.list, &ctx->ltimeout_list);
+	}
+	spin_unlock_irq(&ctx->timeout_lock);
+	/* drop submission reference */
+	io_put_req(req);
+}
+
+static void __io_queue_sqe(struct io_kiocb *req)
+	__must_hold(&req->ctx->uring_lock)
+{
+	struct io_kiocb *linked_timeout;
+	int ret;
+
+issue_sqe:
+	ret = io_issue_sqe(req, IO_URING_F_NONBLOCK|IO_URING_F_COMPLETE_DEFER);
+
+	/*
+	 * We async punt it if the file wasn't marked NOWAIT, or if the file
+	 * doesn't support non-blocking read/write attempts
+	 */
+	if (likely(!ret)) {
+		if (req->flags & REQ_F_COMPLETE_INLINE) {
+			struct io_ring_ctx *ctx = req->ctx;
+			struct io_submit_state *state = &ctx->submit_state;
+
+			state->compl_reqs[state->compl_nr++] = req;
+			if (state->compl_nr == ARRAY_SIZE(state->compl_reqs))
+				io_submit_flush_completions(ctx);
+			return;
+		}
+
+		linked_timeout = io_prep_linked_timeout(req);
+		if (linked_timeout)
+			io_queue_linked_timeout(linked_timeout);
+	} else if (ret == -EAGAIN && !(req->flags & REQ_F_NOWAIT)) {
+		linked_timeout = io_prep_linked_timeout(req);
+
+		switch (io_arm_poll_handler(req)) {
+		case IO_APOLL_READY:
+			if (linked_timeout)
+				io_queue_linked_timeout(linked_timeout);
+			goto issue_sqe;
+		case IO_APOLL_ABORTED:
+			/*
+			 * Queued up for async execution, worker will release
+			 * submit reference when the iocb is actually submitted.
+			 */
+			io_queue_async_work(req, NULL);
+			break;
+		}
+
+		if (linked_timeout)
+			io_queue_linked_timeout(linked_timeout);
+	} else {
+		io_req_complete_failed(req, ret);
+	}
+}
+
+static inline void io_queue_sqe(struct io_kiocb *req)
+	__must_hold(&req->ctx->uring_lock)
+{
+	if (unlikely(req->ctx->drain_active) && io_drain_req(req))
+		return;
+
+	if (likely(!(req->flags & (REQ_F_FORCE_ASYNC | REQ_F_FAIL)))) {
+		__io_queue_sqe(req);
+	} else if (req->flags & REQ_F_FAIL) {
+		io_req_complete_fail_submit(req);
+	} else {
+		int ret = io_req_prep_async(req);
+
+		if (unlikely(ret))
+			io_req_complete_failed(req, ret);
+		else
+			io_queue_async_work(req, NULL);
+	}
+}
+
+/*
+ * Check SQE restrictions (opcode and flags).
+ *
+ * Returns 'true' if SQE is allowed, 'false' otherwise.
+ */
+static inline bool io_check_restriction(struct io_ring_ctx *ctx,
+					struct io_kiocb *req,
+					unsigned int sqe_flags)
+{
+	if (likely(!ctx->restricted))
+		return true;
+
+	if (!test_bit(req->opcode, ctx->restrictions.sqe_op))
+		return false;
+
+	if ((sqe_flags & ctx->restrictions.sqe_flags_required) !=
+	    ctx->restrictions.sqe_flags_required)
+		return false;
+
+	if (sqe_flags & ~(ctx->restrictions.sqe_flags_allowed |
+			  ctx->restrictions.sqe_flags_required))
+		return false;
+
+	return true;
+}
+
+static int io_init_req(struct io_ring_ctx *ctx, struct io_kiocb *req,
+		       const struct io_uring_sqe *sqe)
+	__must_hold(&ctx->uring_lock)
+{
+	struct io_submit_state *state;
+	unsigned int sqe_flags;
+	int personality, ret = 0;
+
+	/* req is partially pre-initialised, see io_preinit_req() */
+	req->opcode = READ_ONCE(sqe->opcode);
+	/* same numerical values with corresponding REQ_F_*, safe to copy */
+	req->flags = sqe_flags = READ_ONCE(sqe->flags);
+	req->user_data = READ_ONCE(sqe->user_data);
+	req->file = NULL;
+	req->fixed_rsrc_refs = NULL;
+	req->task = current;
+
+	/* enforce forwards compatibility on users */
+	if (unlikely(sqe_flags & ~SQE_VALID_FLAGS))
+		return -EINVAL;
+	if (unlikely(req->opcode >= IORING_OP_LAST))
+		return -EINVAL;
+	if (!io_check_restriction(ctx, req, sqe_flags))
+		return -EACCES;
+
+	if ((sqe_flags & IOSQE_BUFFER_SELECT) &&
+	    !io_op_defs[req->opcode].buffer_select)
+		return -EOPNOTSUPP;
+	if (unlikely(sqe_flags & IOSQE_IO_DRAIN))
+		ctx->drain_active = true;
+
+	personality = READ_ONCE(sqe->personality);
+	if (personality) {
+		req->creds = xa_load(&ctx->personalities, personality);
+		if (!req->creds)
+			return -EINVAL;
+		get_cred(req->creds);
+		req->flags |= REQ_F_CREDS;
+	}
+	state = &ctx->submit_state;
+
+	/*
+	 * Plug now if we have more than 1 IO left after this, and the target
+	 * is potentially a read/write to block based storage.
+	 */
+	if (!state->plug_started && state->ios_left > 1 &&
+	    io_op_defs[req->opcode].plug) {
+		blk_start_plug(&state->plug);
+		state->plug_started = true;
+	}
+
+	if (io_op_defs[req->opcode].needs_file) {
+		req->file = io_file_get(ctx, req, READ_ONCE(sqe->fd),
+					(sqe_flags & IOSQE_FIXED_FILE),
+					IO_URING_F_NONBLOCK);
+		if (unlikely(!req->file))
+			ret = -EBADF;
+	}
+
+	state->ios_left--;
+	return ret;
+}
+
+static int io_submit_sqe(struct io_ring_ctx *ctx, struct io_kiocb *req,
+			 const struct io_uring_sqe *sqe)
+	__must_hold(&ctx->uring_lock)
+{
+	struct io_submit_link *link = &ctx->submit_state.link;
+	int ret;
+
+	ret = io_init_req(ctx, req, sqe);
+	if (unlikely(ret)) {
+fail_req:
+		/* fail even hard links since we don't submit */
+		if (link->head) {
+			/*
+			 * we can judge a link req is failed or cancelled by if
+			 * REQ_F_FAIL is set, but the head is an exception since
+			 * it may be set REQ_F_FAIL because of other req's failure
+			 * so let's leverage req->result to distinguish if a head
+			 * is set REQ_F_FAIL because of its failure or other req's
+			 * failure so that we can set the correct ret code for it.
+			 * init result here to avoid affecting the normal path.
+			 */
+			if (!(link->head->flags & REQ_F_FAIL))
+				req_fail_link_node(link->head, -ECANCELED);
+		} else if (!(req->flags & (REQ_F_LINK | REQ_F_HARDLINK))) {
+			/*
+			 * the current req is a normal req, we should return
+			 * error and thus break the submittion loop.
+			 */
+			io_req_complete_failed(req, ret);
+			return ret;
+		}
+		req_fail_link_node(req, ret);
+	} else {
+		ret = io_req_prep(req, sqe);
+		if (unlikely(ret))
+			goto fail_req;
+	}
+
+	/* don't need @sqe from now on */
+	trace_io_uring_submit_sqe(ctx, req, req->opcode, req->user_data,
+				  req->flags, true,
+				  ctx->flags & IORING_SETUP_SQPOLL);
+
+	/*
+	 * If we already have a head request, queue this one for async
+	 * submittal once the head completes. If we don't have a head but
+	 * IOSQE_IO_LINK is set in the sqe, start a new head. This one will be
+	 * submitted sync once the chain is complete. If none of those
+	 * conditions are true (normal request), then just queue it.
+	 */
+	if (link->head) {
+		struct io_kiocb *head = link->head;
+
+		if (!(req->flags & REQ_F_FAIL)) {
+			ret = io_req_prep_async(req);
+			if (unlikely(ret)) {
+				req_fail_link_node(req, ret);
+				if (!(head->flags & REQ_F_FAIL))
+					req_fail_link_node(head, -ECANCELED);
+			}
+		}
+		trace_io_uring_link(ctx, req, head);
+		link->last->link = req;
+		link->last = req;
+
+		/* last request of a link, enqueue the link */
+		if (!(req->flags & (REQ_F_LINK | REQ_F_HARDLINK))) {
+			link->head = NULL;
+			io_queue_sqe(head);
+		}
+	} else {
+		if (req->flags & (REQ_F_LINK | REQ_F_HARDLINK)) {
+			link->head = req;
+			link->last = req;
+		} else {
+			io_queue_sqe(req);
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * Batched submission is done, ensure local IO is flushed out.
+ */
+static void io_submit_state_end(struct io_submit_state *state,
+				struct io_ring_ctx *ctx)
+{
+	if (state->link.head)
+		io_queue_sqe(state->link.head);
+	if (state->compl_nr)
+		io_submit_flush_completions(ctx);
+	if (state->plug_started)
+		blk_finish_plug(&state->plug);
+}
+
+/*
+ * Start submission side cache.
+ */
+static void io_submit_state_start(struct io_submit_state *state,
+				  unsigned int max_ios)
+{
+	state->plug_started = false;
+	state->ios_left = max_ios;
+	/* set only head, no need to init link_last in advance */
+	state->link.head = NULL;
+}
+
+static void io_commit_sqring(struct io_ring_ctx *ctx)
+{
+	struct io_rings *rings = ctx->rings;
+
+	/*
+	 * Ensure any loads from the SQEs are done at this point,
+	 * since once we write the new head, the application could
+	 * write new data to them.
+	 */
+	smp_store_release(&rings->sq.head, ctx->cached_sq_head);
+}
+
+/*
+ * Fetch an sqe, if one is available. Note this returns a pointer to memory
+ * that is mapped by userspace. This means that care needs to be taken to
+ * ensure that reads are stable, as we cannot rely on userspace always
+ * being a good citizen. If members of the sqe are validated and then later
+ * used, it's important that those reads are done through READ_ONCE() to
+ * prevent a re-load down the line.
+ */
+static const struct io_uring_sqe *io_get_sqe(struct io_ring_ctx *ctx)
+{
+	unsigned head, mask = ctx->sq_entries - 1;
+	unsigned sq_idx = ctx->cached_sq_head++ & mask;
+
+	/*
+	 * The cached sq head (or cq tail) serves two purposes:
+	 *
+	 * 1) allows us to batch the cost of updating the user visible
+	 *    head updates.
+	 * 2) allows the kernel side to track the head on its own, even
+	 *    though the application is the one updating it.
+	 */
+	head = READ_ONCE(ctx->sq_array[sq_idx]);
+	if (likely(head < ctx->sq_entries))
+		return &ctx->sq_sqes[head];
+
+	/* drop invalid entries */
+	spin_lock(&ctx->completion_lock);
+	ctx->cq_extra--;
+	spin_unlock(&ctx->completion_lock);
+	WRITE_ONCE(ctx->rings->sq_dropped,
+		   READ_ONCE(ctx->rings->sq_dropped) + 1);
+	return NULL;
+}
+
+static int io_submit_sqes(struct io_ring_ctx *ctx, unsigned int nr)
+	__must_hold(&ctx->uring_lock)
+{
+	int submitted = 0;
+
+	/* make sure SQ entry isn't read before tail */
+	nr = min3(nr, ctx->sq_entries, io_sqring_entries(ctx));
+	if (!percpu_ref_tryget_many(&ctx->refs, nr))
+		return -EAGAIN;
+	io_get_task_refs(nr);
+
+	io_submit_state_start(&ctx->submit_state, nr);
+	while (submitted < nr) {
+		const struct io_uring_sqe *sqe;
+		struct io_kiocb *req;
+
+		req = io_alloc_req(ctx);
+		if (unlikely(!req)) {
+			if (!submitted)
+				submitted = -EAGAIN;
+			break;
+		}
+		sqe = io_get_sqe(ctx);
+		if (unlikely(!sqe)) {
+			list_add(&req->inflight_entry, &ctx->submit_state.free_list);
+			break;
+		}
+		/* will complete beyond this point, count as submitted */
+		submitted++;
+		if (io_submit_sqe(ctx, req, sqe))
+			break;
+	}
+
+	if (unlikely(submitted != nr)) {
+		int ref_used = (submitted == -EAGAIN) ? 0 : submitted;
+		int unused = nr - ref_used;
+
+		current->io_uring->cached_refs += unused;
+		percpu_ref_put_many(&ctx->refs, unused);
+	}
+
+	io_submit_state_end(&ctx->submit_state, ctx);
+	 /* Commit SQ ring head once we've consumed and submitted all SQEs */
+	io_commit_sqring(ctx);
+
+	return submitted;
+}
+
+static inline bool io_sqd_events_pending(struct io_sq_data *sqd)
+{
+	return READ_ONCE(sqd->state);
+}
+
+static inline void io_ring_set_wakeup_flag(struct io_ring_ctx *ctx)
+{
+	/* Tell userspace we may need a wakeup call */
+	spin_lock(&ctx->completion_lock);
+	WRITE_ONCE(ctx->rings->sq_flags,
+		   ctx->rings->sq_flags | IORING_SQ_NEED_WAKEUP);
+	spin_unlock(&ctx->completion_lock);
+}
+
+static inline void io_ring_clear_wakeup_flag(struct io_ring_ctx *ctx)
+{
+	spin_lock(&ctx->completion_lock);
+	WRITE_ONCE(ctx->rings->sq_flags,
+		   ctx->rings->sq_flags & ~IORING_SQ_NEED_WAKEUP);
+	spin_unlock(&ctx->completion_lock);
+}
+
+static int __io_sq_thread(struct io_ring_ctx *ctx, bool cap_entries)
+{
+	unsigned int to_submit;
+	int ret = 0;
+
+	to_submit = io_sqring_entries(ctx);
+	/* if we're handling multiple rings, cap submit size for fairness */
+	if (cap_entries && to_submit > IORING_SQPOLL_CAP_ENTRIES_VALUE)
+		to_submit = IORING_SQPOLL_CAP_ENTRIES_VALUE;
+
+	if (!list_empty(&ctx->iopoll_list) || to_submit) {
+		unsigned nr_events = 0;
+		const struct cred *creds = NULL;
+
+		if (ctx->sq_creds != current_cred())
+			creds = override_creds(ctx->sq_creds);
+
+		mutex_lock(&ctx->uring_lock);
+		if (!list_empty(&ctx->iopoll_list))
+			io_do_iopoll(ctx, &nr_events, 0);
+
+		/*
+		 * Don't submit if refs are dying, good for io_uring_register(),
+		 * but also it is relied upon by io_ring_exit_work()
+		 */
+		if (to_submit && likely(!percpu_ref_is_dying(&ctx->refs)) &&
+		    !(ctx->flags & IORING_SETUP_R_DISABLED))
+			ret = io_submit_sqes(ctx, to_submit);
+		mutex_unlock(&ctx->uring_lock);
+
+		if (to_submit && wq_has_sleeper(&ctx->sqo_sq_wait))
+			wake_up(&ctx->sqo_sq_wait);
+		if (creds)
+			revert_creds(creds);
+	}
+
+	return ret;
+}
+
+static void io_sqd_update_thread_idle(struct io_sq_data *sqd)
+{
+	struct io_ring_ctx *ctx;
+	unsigned sq_thread_idle = 0;
+
+	list_for_each_entry(ctx, &sqd->ctx_list, sqd_list)
+		sq_thread_idle = max(sq_thread_idle, ctx->sq_thread_idle);
+	sqd->sq_thread_idle = sq_thread_idle;
+}
+
+static bool io_sqd_handle_event(struct io_sq_data *sqd)
+{
+	bool did_sig = false;
+	struct ksignal ksig;
+
+	if (test_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state) ||
+	    signal_pending(current)) {
+		mutex_unlock(&sqd->lock);
+		if (signal_pending(current))
+			did_sig = get_signal(&ksig);
+		cond_resched();
+		mutex_lock(&sqd->lock);
+	}
+	return did_sig || test_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state);
+}
+
+static int io_sq_thread(void *data)
+{
+	struct io_sq_data *sqd = data;
+	struct io_ring_ctx *ctx;
+	unsigned long timeout = 0;
+	char buf[TASK_COMM_LEN];
+	DEFINE_WAIT(wait);
+
+	snprintf(buf, sizeof(buf), "iou-sqp-%d", sqd->task_pid);
+	set_task_comm(current, buf);
+
+	if (sqd->sq_cpu != -1)
+		set_cpus_allowed_ptr(current, cpumask_of(sqd->sq_cpu));
+	else
+		set_cpus_allowed_ptr(current, cpu_online_mask);
+	current->flags |= PF_NO_SETAFFINITY;
+
+	mutex_lock(&sqd->lock);
+	while (1) {
+		bool cap_entries, sqt_spin = false;
+
+		if (io_sqd_events_pending(sqd) || signal_pending(current)) {
+			if (io_sqd_handle_event(sqd))
+				break;
+			timeout = jiffies + sqd->sq_thread_idle;
+		}
+
+		cap_entries = !list_is_singular(&sqd->ctx_list);
+		list_for_each_entry(ctx, &sqd->ctx_list, sqd_list) {
+			int ret = __io_sq_thread(ctx, cap_entries);
+
+			if (!sqt_spin && (ret > 0 || !list_empty(&ctx->iopoll_list)))
+				sqt_spin = true;
+		}
+		if (io_run_task_work())
+			sqt_spin = true;
+
+		if (sqt_spin || !time_after(jiffies, timeout)) {
+			cond_resched();
+			if (sqt_spin)
+				timeout = jiffies + sqd->sq_thread_idle;
+			continue;
+		}
+
+		prepare_to_wait(&sqd->wait, &wait, TASK_INTERRUPTIBLE);
+		if (!io_sqd_events_pending(sqd) && !current->task_works) {
+			bool needs_sched = true;
+
+			list_for_each_entry(ctx, &sqd->ctx_list, sqd_list) {
+				io_ring_set_wakeup_flag(ctx);
+
+				if ((ctx->flags & IORING_SETUP_IOPOLL) &&
+				    !list_empty_careful(&ctx->iopoll_list)) {
+					needs_sched = false;
+					break;
+				}
+				if (io_sqring_entries(ctx)) {
+					needs_sched = false;
+					break;
+				}
+			}
+
+			if (needs_sched) {
+				mutex_unlock(&sqd->lock);
+				schedule();
+				mutex_lock(&sqd->lock);
+			}
+			list_for_each_entry(ctx, &sqd->ctx_list, sqd_list)
+				io_ring_clear_wakeup_flag(ctx);
+		}
+
+		finish_wait(&sqd->wait, &wait);
+		timeout = jiffies + sqd->sq_thread_idle;
+	}
+
+	io_uring_cancel_generic(true, sqd);
+	sqd->thread = NULL;
+	list_for_each_entry(ctx, &sqd->ctx_list, sqd_list)
+		io_ring_set_wakeup_flag(ctx);
+	io_run_task_work();
+	mutex_unlock(&sqd->lock);
+
+	complete(&sqd->exited);
+	do_exit(0);
+}
+
+struct io_wait_queue {
+	struct wait_queue_entry wq;
+	struct io_ring_ctx *ctx;
+	unsigned cq_tail;
+	unsigned nr_timeouts;
+};
+
+static inline bool io_should_wake(struct io_wait_queue *iowq)
+{
+	struct io_ring_ctx *ctx = iowq->ctx;
+	int dist = ctx->cached_cq_tail - (int) iowq->cq_tail;
+
+	/*
+	 * Wake up if we have enough events, or if a timeout occurred since we
+	 * started waiting. For timeouts, we always want to return to userspace,
+	 * regardless of event count.
+	 */
+	return dist >= 0 || atomic_read(&ctx->cq_timeouts) != iowq->nr_timeouts;
+}
+
+static int io_wake_function(struct wait_queue_entry *curr, unsigned int mode,
+			    int wake_flags, void *key)
+{
+	struct io_wait_queue *iowq = container_of(curr, struct io_wait_queue,
+							wq);
+
+	/*
+	 * Cannot safely flush overflowed CQEs from here, ensure we wake up
+	 * the task, and the next invocation will do it.
+	 */
+	if (io_should_wake(iowq) || test_bit(0, &iowq->ctx->check_cq_overflow))
+		return autoremove_wake_function(curr, mode, wake_flags, key);
+	return -1;
+}
+
+static int io_run_task_work_sig(void)
+{
+	if (io_run_task_work())
+		return 1;
+	if (!signal_pending(current))
+		return 0;
+	if (test_thread_flag(TIF_NOTIFY_SIGNAL))
+		return -ERESTARTSYS;
+	return -EINTR;
+}
+
+static bool current_pending_io(void)
+{
+	struct io_uring_task *tctx = current->io_uring;
+
+	if (!tctx)
+		return false;
+	return percpu_counter_read_positive(&tctx->inflight);
+}
+
+/* when returns >0, the caller should retry */
+static inline int io_cqring_wait_schedule(struct io_ring_ctx *ctx,
+					  struct io_wait_queue *iowq,
+					  ktime_t *timeout)
+{
+	int ret;
+
+	/* make sure we run task_work before checking for signals */
+	ret = io_run_task_work_sig();
+	if (ret || io_should_wake(iowq))
+		return ret;
+	/* let the caller flush overflows, retry */
+	if (test_bit(0, &ctx->check_cq_overflow))
+		return 1;
+
+	/*
+	 * Mark us as being in io_wait if we have pending requests, so cpufreq
+	 * can take into account that the task is waiting for IO - turns out
+	 * to be important for low QD IO.
+	 */
+	if (current_pending_io())
+		current->in_iowait = 1;
+	ret = 1;
+	if (!schedule_hrtimeout(timeout, HRTIMER_MODE_ABS))
+		ret = -ETIME;
+	current->in_iowait = 0;
+	return ret;
+}
+
+/*
+ * Wait until events become available, if we don't already have some. The
+ * application must reap them itself, as they reside on the shared cq ring.
+ */
+static int io_cqring_wait(struct io_ring_ctx *ctx, int min_events,
+			  const sigset_t __user *sig, size_t sigsz,
+			  struct __kernel_timespec __user *uts)
+{
+	struct io_wait_queue iowq;
+	struct io_rings *rings = ctx->rings;
+	ktime_t timeout = KTIME_MAX;
+	int ret;
+
+	do {
+		io_cqring_overflow_flush(ctx);
+		if (io_cqring_events(ctx) >= min_events)
+			return 0;
+		if (!io_run_task_work())
+			break;
+	} while (1);
+
+	if (uts) {
+		struct timespec64 ts;
+
+		if (get_timespec64(&ts, uts))
+			return -EFAULT;
+		timeout = ktime_add_ns(timespec64_to_ktime(ts), ktime_get_ns());
+	}
+
+	if (sig) {
+#ifdef CONFIG_COMPAT
+		if (in_compat_syscall())
+			ret = set_compat_user_sigmask((const compat_sigset_t __user *)sig,
+						      sigsz);
+		else
+#endif
+			ret = set_user_sigmask(sig, sigsz);
+
+		if (ret)
+			return ret;
+	}
+
+	init_waitqueue_func_entry(&iowq.wq, io_wake_function);
+	iowq.wq.private = current;
+	INIT_LIST_HEAD(&iowq.wq.entry);
+	iowq.ctx = ctx;
+	iowq.nr_timeouts = atomic_read(&ctx->cq_timeouts);
+	iowq.cq_tail = READ_ONCE(ctx->rings->cq.head) + min_events;
+
+	trace_io_uring_cqring_wait(ctx, min_events);
+	do {
+		/* if we can't even flush overflow, don't wait for more */
+		if (!io_cqring_overflow_flush(ctx)) {
+			ret = -EBUSY;
+			break;
+		}
+		prepare_to_wait_exclusive(&ctx->cq_wait, &iowq.wq,
+						TASK_INTERRUPTIBLE);
+		ret = io_cqring_wait_schedule(ctx, &iowq, &timeout);
+		finish_wait(&ctx->cq_wait, &iowq.wq);
+		cond_resched();
+	} while (ret > 0);
+
+	restore_saved_sigmask_unless(ret == -EINTR);
+
+	return READ_ONCE(rings->cq.head) == READ_ONCE(rings->cq.tail) ? ret : 0;
+}
+
+static void io_free_page_table(void **table, size_t size)
+{
+	unsigned i, nr_tables = DIV_ROUND_UP(size, PAGE_SIZE);
+
+	for (i = 0; i < nr_tables; i++)
+		kfree(table[i]);
+	kfree(table);
+}
+
+static void **io_alloc_page_table(size_t size)
+{
+	unsigned i, nr_tables = DIV_ROUND_UP(size, PAGE_SIZE);
+	size_t init_size = size;
+	void **table;
+
+	table = kcalloc(nr_tables, sizeof(*table), GFP_KERNEL_ACCOUNT);
+	if (!table)
+		return NULL;
+
+	for (i = 0; i < nr_tables; i++) {
+		unsigned int this_size = min_t(size_t, size, PAGE_SIZE);
+
+		table[i] = kzalloc(this_size, GFP_KERNEL_ACCOUNT);
+		if (!table[i]) {
+			io_free_page_table(table, init_size);
+			return NULL;
+		}
+		size -= this_size;
+	}
+	return table;
+}
+
+static void io_rsrc_node_destroy(struct io_rsrc_node *ref_node)
+{
+	percpu_ref_exit(&ref_node->refs);
+	kfree(ref_node);
+}
+
+static void io_rsrc_node_ref_zero(struct percpu_ref *ref)
+{
+	struct io_rsrc_node *node = container_of(ref, struct io_rsrc_node, refs);
+	struct io_ring_ctx *ctx = node->rsrc_data->ctx;
+	unsigned long flags;
+	bool first_add = false;
+	unsigned long delay = HZ;
+
+	spin_lock_irqsave(&ctx->rsrc_ref_lock, flags);
+	node->done = true;
+
+	/* if we are mid-quiesce then do not delay */
+	if (node->rsrc_data->quiesce)
+		delay = 0;
+
+	while (!list_empty(&ctx->rsrc_ref_list)) {
+		node = list_first_entry(&ctx->rsrc_ref_list,
+					    struct io_rsrc_node, node);
+		/* recycle ref nodes in order */
+		if (!node->done)
+			break;
+		list_del(&node->node);
+		first_add |= llist_add(&node->llist, &ctx->rsrc_put_llist);
+	}
+	spin_unlock_irqrestore(&ctx->rsrc_ref_lock, flags);
+
+	if (first_add)
+		mod_delayed_work(system_wq, &ctx->rsrc_put_work, delay);
+}
+
+static struct io_rsrc_node *io_rsrc_node_alloc(struct io_ring_ctx *ctx)
+{
+	struct io_rsrc_node *ref_node;
+
+	ref_node = kzalloc(sizeof(*ref_node), GFP_KERNEL);
+	if (!ref_node)
+		return NULL;
+
+	if (percpu_ref_init(&ref_node->refs, io_rsrc_node_ref_zero,
+			    0, GFP_KERNEL)) {
+		kfree(ref_node);
+		return NULL;
+	}
+	INIT_LIST_HEAD(&ref_node->node);
+	INIT_LIST_HEAD(&ref_node->rsrc_list);
+	ref_node->done = false;
+	return ref_node;
+}
+
+static void io_rsrc_node_switch(struct io_ring_ctx *ctx,
+				struct io_rsrc_data *data_to_kill)
+{
+	WARN_ON_ONCE(!ctx->rsrc_backup_node);
+	WARN_ON_ONCE(data_to_kill && !ctx->rsrc_node);
+
+	if (data_to_kill) {
+		struct io_rsrc_node *rsrc_node = ctx->rsrc_node;
+
+		rsrc_node->rsrc_data = data_to_kill;
+		spin_lock_irq(&ctx->rsrc_ref_lock);
+		list_add_tail(&rsrc_node->node, &ctx->rsrc_ref_list);
+		spin_unlock_irq(&ctx->rsrc_ref_lock);
+
+		atomic_inc(&data_to_kill->refs);
+		percpu_ref_kill(&rsrc_node->refs);
+		ctx->rsrc_node = NULL;
+	}
+
+	if (!ctx->rsrc_node) {
+		ctx->rsrc_node = ctx->rsrc_backup_node;
+		ctx->rsrc_backup_node = NULL;
+	}
+}
+
+static int io_rsrc_node_switch_start(struct io_ring_ctx *ctx)
+{
+	if (ctx->rsrc_backup_node)
+		return 0;
+	ctx->rsrc_backup_node = io_rsrc_node_alloc(ctx);
+	return ctx->rsrc_backup_node ? 0 : -ENOMEM;
+}
+
+static int io_rsrc_ref_quiesce(struct io_rsrc_data *data, struct io_ring_ctx *ctx)
+{
+	int ret;
+
+	/* As we may drop ->uring_lock, other task may have started quiesce */
+	if (data->quiesce)
+		return -ENXIO;
+
+	data->quiesce = true;
+	do {
+		ret = io_rsrc_node_switch_start(ctx);
+		if (ret)
+			break;
+		io_rsrc_node_switch(ctx, data);
+
+		/* kill initial ref, already quiesced if zero */
+		if (atomic_dec_and_test(&data->refs))
+			break;
+		mutex_unlock(&ctx->uring_lock);
+		flush_delayed_work(&ctx->rsrc_put_work);
+		ret = wait_for_completion_interruptible(&data->done);
+		if (!ret) {
+			mutex_lock(&ctx->uring_lock);
+			if (atomic_read(&data->refs) > 0) {
+				/*
+				 * it has been revived by another thread while
+				 * we were unlocked
+				 */
+				mutex_unlock(&ctx->uring_lock);
+			} else {
+				break;
+			}
+		}
+
+		atomic_inc(&data->refs);
+		/* wait for all works potentially completing data->done */
+		flush_delayed_work(&ctx->rsrc_put_work);
+		reinit_completion(&data->done);
+
+		ret = io_run_task_work_sig();
+		mutex_lock(&ctx->uring_lock);
+	} while (ret >= 0);
+	data->quiesce = false;
+
+	return ret;
+}
+
+static u64 *io_get_tag_slot(struct io_rsrc_data *data, unsigned int idx)
+{
+	unsigned int off = idx & IO_RSRC_TAG_TABLE_MASK;
+	unsigned int table_idx = idx >> IO_RSRC_TAG_TABLE_SHIFT;
+
+	return &data->tags[table_idx][off];
+}
+
+static void io_rsrc_data_free(struct io_rsrc_data *data)
+{
+	size_t size = data->nr * sizeof(data->tags[0][0]);
+
+	if (data->tags)
+		io_free_page_table((void **)data->tags, size);
+	kfree(data);
+}
+
+static int io_rsrc_data_alloc(struct io_ring_ctx *ctx, rsrc_put_fn *do_put,
+			      u64 __user *utags, unsigned nr,
+			      struct io_rsrc_data **pdata)
+{
+	struct io_rsrc_data *data;
+	int ret = -ENOMEM;
+	unsigned i;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+	data->tags = (u64 **)io_alloc_page_table(nr * sizeof(data->tags[0][0]));
+	if (!data->tags) {
+		kfree(data);
+		return -ENOMEM;
+	}
+
+	data->nr = nr;
+	data->ctx = ctx;
+	data->do_put = do_put;
+	if (utags) {
+		ret = -EFAULT;
+		for (i = 0; i < nr; i++) {
+			u64 *tag_slot = io_get_tag_slot(data, i);
+
+			if (copy_from_user(tag_slot, &utags[i],
+					   sizeof(*tag_slot)))
+				goto fail;
+		}
+	}
+
+	atomic_set(&data->refs, 1);
+	init_completion(&data->done);
+	*pdata = data;
+	return 0;
+fail:
+	io_rsrc_data_free(data);
+	return ret;
+}
+
+static bool io_alloc_file_tables(struct io_file_table *table, unsigned nr_files)
+{
+	table->files = kvcalloc(nr_files, sizeof(table->files[0]),
+				GFP_KERNEL_ACCOUNT);
+	return !!table->files;
+}
+
+static void io_free_file_tables(struct io_file_table *table)
+{
+	kvfree(table->files);
+	table->files = NULL;
+}
+
+static void __io_sqe_files_unregister(struct io_ring_ctx *ctx)
+{
+	int i;
+
+	for (i = 0; i < ctx->nr_user_files; i++) {
+		struct file *file;
+
+		file = io_file_from_index(ctx, i);
+		if (file)
+			fput(file);
+	}
+	io_free_file_tables(&ctx->file_table);
+	io_rsrc_data_free(ctx->file_data);
+	ctx->file_data = NULL;
+	ctx->nr_user_files = 0;
+}
+
+static int io_sqe_files_unregister(struct io_ring_ctx *ctx)
+{
+	unsigned nr = ctx->nr_user_files;
+	int ret;
+
+	if (!ctx->file_data)
+		return -ENXIO;
+
+	/*
+	 * Quiesce may unlock ->uring_lock, and while it's not held
+	 * prevent new requests using the table.
+	 */
+	ctx->nr_user_files = 0;
+	ret = io_rsrc_ref_quiesce(ctx->file_data, ctx);
+	ctx->nr_user_files = nr;
+	if (!ret)
+		__io_sqe_files_unregister(ctx);
+	return ret;
+}
+
+static void io_sq_thread_unpark(struct io_sq_data *sqd)
+	__releases(&sqd->lock)
+{
+	WARN_ON_ONCE(sqd->thread == current);
+
+	/*
+	 * Do the dance but not conditional clear_bit() because it'd race with
+	 * other threads incrementing park_pending and setting the bit.
+	 */
+	clear_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state);
+	if (atomic_dec_return(&sqd->park_pending))
+		set_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state);
+	mutex_unlock(&sqd->lock);
+}
+
+static void io_sq_thread_park(struct io_sq_data *sqd)
+	__acquires(&sqd->lock)
+{
+	WARN_ON_ONCE(sqd->thread == current);
+
+	atomic_inc(&sqd->park_pending);
+	set_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state);
+	mutex_lock(&sqd->lock);
+	if (sqd->thread)
+		wake_up_process(sqd->thread);
+}
+
+static void io_sq_thread_stop(struct io_sq_data *sqd)
+{
+	WARN_ON_ONCE(sqd->thread == current);
+	WARN_ON_ONCE(test_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state));
+
+	set_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state);
+	mutex_lock(&sqd->lock);
+	if (sqd->thread)
+		wake_up_process(sqd->thread);
+	mutex_unlock(&sqd->lock);
+	wait_for_completion(&sqd->exited);
+}
+
+static void io_put_sq_data(struct io_sq_data *sqd)
+{
+	if (refcount_dec_and_test(&sqd->refs)) {
+		WARN_ON_ONCE(atomic_read(&sqd->park_pending));
+
+		io_sq_thread_stop(sqd);
+		kfree(sqd);
+	}
+}
+
+static void io_sq_thread_finish(struct io_ring_ctx *ctx)
+{
+	struct io_sq_data *sqd = ctx->sq_data;
+
+	if (sqd) {
+		io_sq_thread_park(sqd);
+		list_del_init(&ctx->sqd_list);
+		io_sqd_update_thread_idle(sqd);
+		io_sq_thread_unpark(sqd);
+
+		io_put_sq_data(sqd);
+		ctx->sq_data = NULL;
+	}
+}
+
+static struct io_sq_data *io_attach_sq_data(struct io_uring_params *p)
+{
+	struct io_ring_ctx *ctx_attach;
+	struct io_sq_data *sqd;
+	struct fd f;
+
+	f = fdget(p->wq_fd);
+	if (!f.file)
+		return ERR_PTR(-ENXIO);
+	if (f.file->f_op != &io_uring_fops) {
+		fdput(f);
+		return ERR_PTR(-EINVAL);
+	}
+
+	ctx_attach = f.file->private_data;
+	sqd = ctx_attach->sq_data;
+	if (!sqd) {
+		fdput(f);
+		return ERR_PTR(-EINVAL);
+	}
+	if (sqd->task_tgid != current->tgid) {
+		fdput(f);
+		return ERR_PTR(-EPERM);
+	}
+
+	refcount_inc(&sqd->refs);
+	fdput(f);
+	return sqd;
+}
+
+static struct io_sq_data *io_get_sq_data(struct io_uring_params *p,
+					 bool *attached)
+{
+	struct io_sq_data *sqd;
+
+	*attached = false;
+	if (p->flags & IORING_SETUP_ATTACH_WQ) {
+		sqd = io_attach_sq_data(p);
+		if (!IS_ERR(sqd)) {
+			*attached = true;
+			return sqd;
+		}
+		/* fall through for EPERM case, setup new sqd/task */
+		if (PTR_ERR(sqd) != -EPERM)
+			return sqd;
+	}
+
+	sqd = kzalloc(sizeof(*sqd), GFP_KERNEL);
+	if (!sqd)
+		return ERR_PTR(-ENOMEM);
+
+	atomic_set(&sqd->park_pending, 0);
+	refcount_set(&sqd->refs, 1);
+	INIT_LIST_HEAD(&sqd->ctx_list);
+	mutex_init(&sqd->lock);
+	init_waitqueue_head(&sqd->wait);
+	init_completion(&sqd->exited);
+	return sqd;
+}
+
+static void io_rsrc_file_put(struct io_ring_ctx *ctx, struct io_rsrc_put *prsrc)
+{
+	struct file *file = prsrc->file;
+
+	fput(file);
+}
+
+static void __io_rsrc_put_work(struct io_rsrc_node *ref_node)
+{
+	struct io_rsrc_data *rsrc_data = ref_node->rsrc_data;
+	struct io_ring_ctx *ctx = rsrc_data->ctx;
+	struct io_rsrc_put *prsrc, *tmp;
+
+	list_for_each_entry_safe(prsrc, tmp, &ref_node->rsrc_list, list) {
+		list_del(&prsrc->list);
+
+		if (prsrc->tag) {
+			bool lock_ring = ctx->flags & IORING_SETUP_IOPOLL;
+
+			io_ring_submit_lock(ctx, lock_ring);
+			spin_lock(&ctx->completion_lock);
+			io_fill_cqe_aux(ctx, prsrc->tag, 0, 0);
+			io_commit_cqring(ctx);
+			spin_unlock(&ctx->completion_lock);
+			io_cqring_ev_posted(ctx);
+			io_ring_submit_unlock(ctx, lock_ring);
+		}
+
+		rsrc_data->do_put(ctx, prsrc);
+		kfree(prsrc);
+	}
+
+	io_rsrc_node_destroy(ref_node);
+	if (atomic_dec_and_test(&rsrc_data->refs))
+		complete(&rsrc_data->done);
+}
+
+static void io_rsrc_put_work(struct work_struct *work)
+{
+	struct io_ring_ctx *ctx;
+	struct llist_node *node;
+
+	ctx = container_of(work, struct io_ring_ctx, rsrc_put_work.work);
+	node = llist_del_all(&ctx->rsrc_put_llist);
+
+	while (node) {
+		struct io_rsrc_node *ref_node;
+		struct llist_node *next = node->next;
+
+		ref_node = llist_entry(node, struct io_rsrc_node, llist);
+		__io_rsrc_put_work(ref_node);
+		node = next;
+	}
+}
+
+static int io_sqe_files_register(struct io_ring_ctx *ctx, void __user *arg,
+				 unsigned nr_args, u64 __user *tags)
+{
+	__s32 __user *fds = (__s32 __user *) arg;
+	struct file *file;
+	int fd, ret;
+	unsigned i;
+
+	if (ctx->file_data)
+		return -EBUSY;
+	if (!nr_args)
+		return -EINVAL;
+	if (nr_args > IORING_MAX_FIXED_FILES)
+		return -EMFILE;
+	if (nr_args > rlimit(RLIMIT_NOFILE))
+		return -EMFILE;
+	ret = io_rsrc_node_switch_start(ctx);
+	if (ret)
+		return ret;
+	ret = io_rsrc_data_alloc(ctx, io_rsrc_file_put, tags, nr_args,
+				 &ctx->file_data);
+	if (ret)
+		return ret;
+
+	ret = -ENOMEM;
+	if (!io_alloc_file_tables(&ctx->file_table, nr_args))
+		goto out_free;
+
+	for (i = 0; i < nr_args; i++, ctx->nr_user_files++) {
+		if (copy_from_user(&fd, &fds[i], sizeof(fd))) {
+			ret = -EFAULT;
+			goto out_fput;
+		}
+		/* allow sparse sets */
+		if (fd == -1) {
+			ret = -EINVAL;
+			if (unlikely(*io_get_tag_slot(ctx->file_data, i)))
+				goto out_fput;
+			continue;
+		}
+
+		file = fget(fd);
+		ret = -EBADF;
+		if (unlikely(!file))
+			goto out_fput;
+
+		/*
+		 * Don't allow io_uring instances to be registered. If UNIX
+		 * isn't enabled, then this causes a reference cycle and this
+		 * instance can never get freed. If UNIX is enabled we'll
+		 * handle it just fine, but there's still no point in allowing
+		 * a ring fd as it doesn't support regular read/write anyway.
+		 */
+		if (file->f_op == &io_uring_fops) {
+			fput(file);
+			goto out_fput;
+		}
+		io_fixed_file_set(io_fixed_file_slot(&ctx->file_table, i), file);
+	}
+
+	io_rsrc_node_switch(ctx, NULL);
+	return 0;
+out_fput:
+	for (i = 0; i < ctx->nr_user_files; i++) {
+		file = io_file_from_index(ctx, i);
+		if (file)
+			fput(file);
+	}
+	io_free_file_tables(&ctx->file_table);
+	ctx->nr_user_files = 0;
+out_free:
+	io_rsrc_data_free(ctx->file_data);
+	ctx->file_data = NULL;
+	return ret;
+}
+
+static int io_queue_rsrc_removal(struct io_rsrc_data *data, unsigned idx,
+				 struct io_rsrc_node *node, void *rsrc)
+{
+	u64 *tag_slot = io_get_tag_slot(data, idx);
+	struct io_rsrc_put *prsrc;
+
+	prsrc = kzalloc(sizeof(*prsrc), GFP_KERNEL);
+	if (!prsrc)
+		return -ENOMEM;
+
+	prsrc->tag = *tag_slot;
+	*tag_slot = 0;
+	prsrc->rsrc = rsrc;
+	list_add(&prsrc->list, &node->rsrc_list);
+	return 0;
+}
+
+static int io_install_fixed_file(struct io_kiocb *req, struct file *file,
+				 unsigned int issue_flags, u32 slot_index)
+{
+	struct io_ring_ctx *ctx = req->ctx;
+	bool force_nonblock = issue_flags & IO_URING_F_NONBLOCK;
+	bool needs_switch = false;
+	struct io_fixed_file *file_slot;
+	int ret = -EBADF;
+
+	io_ring_submit_lock(ctx, !force_nonblock);
+	if (file->f_op == &io_uring_fops)
+		goto err;
+	ret = -ENXIO;
+	if (!ctx->file_data)
+		goto err;
+	ret = -EINVAL;
+	if (slot_index >= ctx->nr_user_files)
+		goto err;
+
+	slot_index = array_index_nospec(slot_index, ctx->nr_user_files);
+	file_slot = io_fixed_file_slot(&ctx->file_table, slot_index);
+
+	if (file_slot->file_ptr) {
+		struct file *old_file;
+
+		ret = io_rsrc_node_switch_start(ctx);
+		if (ret)
+			goto err;
+
+		old_file = (struct file *)(file_slot->file_ptr & FFS_MASK);
+		ret = io_queue_rsrc_removal(ctx->file_data, slot_index,
+					    ctx->rsrc_node, old_file);
+		if (ret)
+			goto err;
+		file_slot->file_ptr = 0;
+		needs_switch = true;
+	}
+
+	*io_get_tag_slot(ctx->file_data, slot_index) = 0;
+	io_fixed_file_set(file_slot, file);
+	ret = 0;
+err:
+	if (needs_switch)
+		io_rsrc_node_switch(ctx, ctx->file_data);
+	io_ring_submit_unlock(ctx, !force_nonblock);
+	if (ret)
+		fput(file);
+	return ret;
+}
+
+static int io_close_fixed(struct io_kiocb *req, unsigned int issue_flags)
+{
+	unsigned int offset = req->close.file_slot - 1;
+	struct io_ring_ctx *ctx = req->ctx;
+	struct io_fixed_file *file_slot;
+	struct file *file;
+	int ret;
+
+	io_ring_submit_lock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+	ret = -ENXIO;
+	if (unlikely(!ctx->file_data))
+		goto out;
+	ret = -EINVAL;
+	if (offset >= ctx->nr_user_files)
+		goto out;
+	ret = io_rsrc_node_switch_start(ctx);
+	if (ret)
+		goto out;
+
+	offset = array_index_nospec(offset, ctx->nr_user_files);
+	file_slot = io_fixed_file_slot(&ctx->file_table, offset);
+	ret = -EBADF;
+	if (!file_slot->file_ptr)
+		goto out;
+
+	file = (struct file *)(file_slot->file_ptr & FFS_MASK);
+	ret = io_queue_rsrc_removal(ctx->file_data, offset, ctx->rsrc_node, file);
+	if (ret)
+		goto out;
+
+	file_slot->file_ptr = 0;
+	io_rsrc_node_switch(ctx, ctx->file_data);
+	ret = 0;
+out:
+	io_ring_submit_unlock(ctx, !(issue_flags & IO_URING_F_NONBLOCK));
+	return ret;
+}
+
+static int __io_sqe_files_update(struct io_ring_ctx *ctx,
+				 struct io_uring_rsrc_update2 *up,
+				 unsigned nr_args)
+{
+	u64 __user *tags = u64_to_user_ptr(up->tags);
+	__s32 __user *fds = u64_to_user_ptr(up->data);
+	struct io_rsrc_data *data = ctx->file_data;
+	struct io_fixed_file *file_slot;
+	struct file *file;
+	int fd, i, err = 0;
+	unsigned int done;
+	bool needs_switch = false;
+
+	if (!ctx->file_data)
+		return -ENXIO;
+	if (up->offset + nr_args > ctx->nr_user_files)
+		return -EINVAL;
+
+	for (done = 0; done < nr_args; done++) {
+		u64 tag = 0;
+
+		if ((tags && copy_from_user(&tag, &tags[done], sizeof(tag))) ||
+		    copy_from_user(&fd, &fds[done], sizeof(fd))) {
+			err = -EFAULT;
+			break;
+		}
+		if ((fd == IORING_REGISTER_FILES_SKIP || fd == -1) && tag) {
+			err = -EINVAL;
+			break;
+		}
+		if (fd == IORING_REGISTER_FILES_SKIP)
+			continue;
+
+		i = array_index_nospec(up->offset + done, ctx->nr_user_files);
+		file_slot = io_fixed_file_slot(&ctx->file_table, i);
+
+		if (file_slot->file_ptr) {
+			file = (struct file *)(file_slot->file_ptr & FFS_MASK);
+			err = io_queue_rsrc_removal(data, i, ctx->rsrc_node, file);
+			if (err)
+				break;
+			file_slot->file_ptr = 0;
+			needs_switch = true;
+		}
+		if (fd != -1) {
+			file = fget(fd);
+			if (!file) {
+				err = -EBADF;
+				break;
+			}
+			/*
+			 * Don't allow io_uring instances to be registered. If
+			 * UNIX isn't enabled, then this causes a reference
+			 * cycle and this instance can never get freed. If UNIX
+			 * is enabled we'll handle it just fine, but there's
+			 * still no point in allowing a ring fd as it doesn't
+			 * support regular read/write anyway.
+			 */
+			if (file->f_op == &io_uring_fops) {
+				fput(file);
+				err = -EBADF;
+				break;
+			}
+			*io_get_tag_slot(data, i) = tag;
+			io_fixed_file_set(file_slot, file);
+		}
+	}
+
+	if (needs_switch)
+		io_rsrc_node_switch(ctx, data);
+	return done ? done : err;
+}
+
+static struct io_wq *io_init_wq_offload(struct io_ring_ctx *ctx,
+					struct task_struct *task)
+{
+	struct io_wq_hash *hash;
+	struct io_wq_data data;
+	unsigned int concurrency;
+
+	mutex_lock(&ctx->uring_lock);
+	hash = ctx->hash_map;
+	if (!hash) {
+		hash = kzalloc(sizeof(*hash), GFP_KERNEL);
+		if (!hash) {
+			mutex_unlock(&ctx->uring_lock);
+			return ERR_PTR(-ENOMEM);
+		}
+		refcount_set(&hash->refs, 1);
+		init_waitqueue_head(&hash->wait);
+		ctx->hash_map = hash;
+	}
+	mutex_unlock(&ctx->uring_lock);
+
+	data.hash = hash;
+	data.task = task;
+	data.free_work = io_wq_free_work;
+	data.do_work = io_wq_submit_work;
+
+	/* Do QD, or 4 * CPUS, whatever is smallest */
+	concurrency = min(ctx->sq_entries, 4 * num_online_cpus());
+
+	return io_wq_create(concurrency, &data);
+}
+
+static int io_uring_alloc_task_context(struct task_struct *task,
+				       struct io_ring_ctx *ctx)
+{
+	struct io_uring_task *tctx;
+	int ret;
+
+	tctx = kzalloc(sizeof(*tctx), GFP_KERNEL);
+	if (unlikely(!tctx))
+		return -ENOMEM;
+
+	ret = percpu_counter_init(&tctx->inflight, 0, GFP_KERNEL);
+	if (unlikely(ret)) {
+		kfree(tctx);
+		return ret;
+	}
+
+	tctx->io_wq = io_init_wq_offload(ctx, task);
+	if (IS_ERR(tctx->io_wq)) {
+		ret = PTR_ERR(tctx->io_wq);
+		percpu_counter_destroy(&tctx->inflight);
+		kfree(tctx);
+		return ret;
+	}
+
+	xa_init(&tctx->xa);
+	init_waitqueue_head(&tctx->wait);
+	atomic_set(&tctx->in_idle, 0);
+	atomic_set(&tctx->inflight_tracked, 0);
+	task->io_uring = tctx;
+	spin_lock_init(&tctx->task_lock);
+	INIT_WQ_LIST(&tctx->task_list);
+	init_task_work(&tctx->task_work, tctx_task_work);
+	return 0;
+}
+
+void __io_uring_free(struct task_struct *tsk)
+{
+	struct io_uring_task *tctx = tsk->io_uring;
+
+	WARN_ON_ONCE(!xa_empty(&tctx->xa));
+	WARN_ON_ONCE(tctx->io_wq);
+	WARN_ON_ONCE(tctx->cached_refs);
+
+	percpu_counter_destroy(&tctx->inflight);
+	kfree(tctx);
+	tsk->io_uring = NULL;
+}
+
+static int io_sq_offload_create(struct io_ring_ctx *ctx,
+				struct io_uring_params *p)
+{
+	int ret;
+
+	/* Retain compatibility with failing for an invalid attach attempt */
+	if ((ctx->flags & (IORING_SETUP_ATTACH_WQ | IORING_SETUP_SQPOLL)) ==
+				IORING_SETUP_ATTACH_WQ) {
+		struct fd f;
+
+		f = fdget(p->wq_fd);
+		if (!f.file)
+			return -ENXIO;
+		if (f.file->f_op != &io_uring_fops) {
+			fdput(f);
+			return -EINVAL;
+		}
+		fdput(f);
+	}
+	if (ctx->flags & IORING_SETUP_SQPOLL) {
+		struct task_struct *tsk;
+		struct io_sq_data *sqd;
+		bool attached;
+
+		sqd = io_get_sq_data(p, &attached);
+		if (IS_ERR(sqd)) {
+			ret = PTR_ERR(sqd);
+			goto err;
+		}
+
+		ctx->sq_creds = get_current_cred();
+		ctx->sq_data = sqd;
+		ctx->sq_thread_idle = msecs_to_jiffies(p->sq_thread_idle);
+		if (!ctx->sq_thread_idle)
+			ctx->sq_thread_idle = HZ;
+
+		io_sq_thread_park(sqd);
+		list_add(&ctx->sqd_list, &sqd->ctx_list);
+		io_sqd_update_thread_idle(sqd);
+		/* don't attach to a dying SQPOLL thread, would be racy */
+		ret = (attached && !sqd->thread) ? -ENXIO : 0;
+		io_sq_thread_unpark(sqd);
+
+		if (ret < 0)
+			goto err;
+		if (attached)
+			return 0;
+
+		if (p->flags & IORING_SETUP_SQ_AFF) {
+			cpumask_var_t allowed_mask;
+			int cpu = p->sq_thread_cpu;
+
+			ret = -EINVAL;
+			if (cpu >= nr_cpu_ids || !cpu_online(cpu))
+				goto err_sqpoll;
+			ret = -ENOMEM;
+			if (!alloc_cpumask_var(&allowed_mask, GFP_KERNEL))
+				goto err_sqpoll;
+			ret = -EINVAL;
+			cpuset_cpus_allowed(current, allowed_mask);
+			if (!cpumask_test_cpu(cpu, allowed_mask)) {
+				free_cpumask_var(allowed_mask);
+				goto err_sqpoll;
+			}
+			free_cpumask_var(allowed_mask);
+			sqd->sq_cpu = cpu;
+		} else {
+			sqd->sq_cpu = -1;
+		}
+
+		sqd->task_pid = current->pid;
+		sqd->task_tgid = current->tgid;
+		tsk = create_io_thread(io_sq_thread, sqd, NUMA_NO_NODE);
+		if (IS_ERR(tsk)) {
+			ret = PTR_ERR(tsk);
+			goto err_sqpoll;
+		}
+
+		sqd->thread = tsk;
+		ret = io_uring_alloc_task_context(tsk, ctx);
+		wake_up_new_task(tsk);
+		if (ret)
+			goto err;
+	} else if (p->flags & IORING_SETUP_SQ_AFF) {
+		/* Can't have SQ_AFF without SQPOLL */
+		ret = -EINVAL;
+		goto err;
+	}
+
+	return 0;
+err_sqpoll:
+	complete(&ctx->sq_data->exited);
+err:
+	io_sq_thread_finish(ctx);
+	return ret;
+}
+
+static inline void __io_unaccount_mem(struct user_struct *user,
+				      unsigned long nr_pages)
+{
+	atomic_long_sub(nr_pages, &user->locked_vm);
+}
+
+static inline int __io_account_mem(struct user_struct *user,
+				   unsigned long nr_pages)
+{
+	unsigned long page_limit, cur_pages, new_pages;
+
+	/* Don't allow more pages than we can safely lock */
+	page_limit = rlimit(RLIMIT_MEMLOCK) >> PAGE_SHIFT;
+
+	do {
+		cur_pages = atomic_long_read(&user->locked_vm);
+		new_pages = cur_pages + nr_pages;
+		if (new_pages > page_limit)
+			return -ENOMEM;
+	} while (atomic_long_cmpxchg(&user->locked_vm, cur_pages,
+					new_pages) != cur_pages);
+
+	return 0;
+}
+
+static void io_unaccount_mem(struct io_ring_ctx *ctx, unsigned long nr_pages)
+{
+	if (ctx->user)
+		__io_unaccount_mem(ctx->user, nr_pages);
+
+	if (ctx->mm_account)
+		atomic64_sub(nr_pages, &ctx->mm_account->pinned_vm);
+}
+
+static int io_account_mem(struct io_ring_ctx *ctx, unsigned long nr_pages)
+{
+	int ret;
+
+	if (ctx->user) {
+		ret = __io_account_mem(ctx->user, nr_pages);
+		if (ret)
+			return ret;
+	}
+
+	if (ctx->mm_account)
+		atomic64_add(nr_pages, &ctx->mm_account->pinned_vm);
+
+	return 0;
+}
+
+static void io_mem_free(void *ptr)
+{
+	struct page *page;
+
+	if (!ptr)
+		return;
+
+	page = virt_to_head_page(ptr);
+	if (put_page_testzero(page))
+		free_compound_page(page);
+}
+
+static void *io_mem_alloc(size_t size)
+{
+	gfp_t gfp = GFP_KERNEL_ACCOUNT | __GFP_ZERO | __GFP_NOWARN | __GFP_COMP;
+
+	return (void *) __get_free_pages(gfp, get_order(size));
+}
+
+static unsigned long rings_size(unsigned sq_entries, unsigned cq_entries,
+				size_t *sq_offset)
+{
+	struct io_rings *rings;
+	size_t off, sq_array_size;
+
+	off = struct_size(rings, cqes, cq_entries);
+	if (off == SIZE_MAX)
+		return SIZE_MAX;
+
+#ifdef CONFIG_SMP
+	off = ALIGN(off, SMP_CACHE_BYTES);
+	if (off == 0)
+		return SIZE_MAX;
+#endif
+
+	if (sq_offset)
+		*sq_offset = off;
+
+	sq_array_size = array_size(sizeof(u32), sq_entries);
+	if (sq_array_size == SIZE_MAX)
+		return SIZE_MAX;
+
+	if (check_add_overflow(off, sq_array_size, &off))
+		return SIZE_MAX;
+
+	return off;
+}
+
+static void io_buffer_unmap(struct io_ring_ctx *ctx, struct io_mapped_ubuf **slot)
+{
+	struct io_mapped_ubuf *imu = *slot;
+	unsigned int i;
+
+	if (imu != ctx->dummy_ubuf) {
+		for (i = 0; i < imu->nr_bvecs; i++)
+			unpin_user_page(imu->bvec[i].bv_page);
+		if (imu->acct_pages)
+			io_unaccount_mem(ctx, imu->acct_pages);
+		kvfree(imu);
+	}
+	*slot = NULL;
+}
+
+static void io_rsrc_buf_put(struct io_ring_ctx *ctx, struct io_rsrc_put *prsrc)
+{
+	io_buffer_unmap(ctx, &prsrc->buf);
+	prsrc->buf = NULL;
+}
+
+static void __io_sqe_buffers_unregister(struct io_ring_ctx *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ctx->nr_user_bufs; i++)
+		io_buffer_unmap(ctx, &ctx->user_bufs[i]);
+	kfree(ctx->user_bufs);
+	io_rsrc_data_free(ctx->buf_data);
+	ctx->user_bufs = NULL;
+	ctx->buf_data = NULL;
+	ctx->nr_user_bufs = 0;
+}
+
+static int io_sqe_buffers_unregister(struct io_ring_ctx *ctx)
+{
+	unsigned nr = ctx->nr_user_bufs;
+	int ret;
+
+	if (!ctx->buf_data)
+		return -ENXIO;
+
+	/*
+	 * Quiesce may unlock ->uring_lock, and while it's not held
+	 * prevent new requests using the table.
+	 */
+	ctx->nr_user_bufs = 0;
+	ret = io_rsrc_ref_quiesce(ctx->buf_data, ctx);
+	ctx->nr_user_bufs = nr;
+	if (!ret)
+		__io_sqe_buffers_unregister(ctx);
+	return ret;
+}
+
+static int io_copy_iov(struct io_ring_ctx *ctx, struct iovec *dst,
+		       void __user *arg, unsigned index)
+{
+	struct iovec __user *src;
+
+#ifdef CONFIG_COMPAT
+	if (ctx->compat) {
+		struct compat_iovec __user *ciovs;
+		struct compat_iovec ciov;
+
+		ciovs = (struct compat_iovec __user *) arg;
+		if (copy_from_user(&ciov, &ciovs[index], sizeof(ciov)))
+			return -EFAULT;
+
+		dst->iov_base = u64_to_user_ptr((u64)ciov.iov_base);
+		dst->iov_len = ciov.iov_len;
+		return 0;
+	}
+#endif
+	src = (struct iovec __user *) arg;
+	if (copy_from_user(dst, &src[index], sizeof(*dst)))
+		return -EFAULT;
+	return 0;
+}
+
+/*
+ * Not super efficient, but this is just a registration time. And we do cache
+ * the last compound head, so generally we'll only do a full search if we don't
+ * match that one.
+ *
+ * We check if the given compound head page has already been accounted, to
+ * avoid double accounting it. This allows us to account the full size of the
+ * page, not just the constituent pages of a huge page.
+ */
+static bool headpage_already_acct(struct io_ring_ctx *ctx, struct page **pages,
+				  int nr_pages, struct page *hpage)
+{
+	int i, j;
+
+	/* check current page array */
+	for (i = 0; i < nr_pages; i++) {
+		if (!PageCompound(pages[i]))
+			continue;
+		if (compound_head(pages[i]) == hpage)
+			return true;
+	}
+
+	/* check previously registered pages */
+	for (i = 0; i < ctx->nr_user_bufs; i++) {
+		struct io_mapped_ubuf *imu = ctx->user_bufs[i];
+
+		for (j = 0; j < imu->nr_bvecs; j++) {
+			if (!PageCompound(imu->bvec[j].bv_page))
+				continue;
+			if (compound_head(imu->bvec[j].bv_page) == hpage)
+				return true;
+		}
+	}
+
+	return false;
+}
+
+static int io_buffer_account_pin(struct io_ring_ctx *ctx, struct page **pages,
+				 int nr_pages, struct io_mapped_ubuf *imu,
+				 struct page **last_hpage)
+{
+	int i, ret;
+
+	imu->acct_pages = 0;
+	for (i = 0; i < nr_pages; i++) {
+		if (!PageCompound(pages[i])) {
+			imu->acct_pages++;
+		} else {
+			struct page *hpage;
+
+			hpage = compound_head(pages[i]);
+			if (hpage == *last_hpage)
+				continue;
+			*last_hpage = hpage;
+			if (headpage_already_acct(ctx, pages, i, hpage))
+				continue;
+			imu->acct_pages += page_size(hpage) >> PAGE_SHIFT;
+		}
+	}
+
+	if (!imu->acct_pages)
+		return 0;
+
+	ret = io_account_mem(ctx, imu->acct_pages);
+	if (ret)
+		imu->acct_pages = 0;
+	return ret;
+}
+
+static int io_sqe_buffer_register(struct io_ring_ctx *ctx, struct iovec *iov,
+				  struct io_mapped_ubuf **pimu,
+				  struct page **last_hpage)
+{
+	struct io_mapped_ubuf *imu = NULL;
+	struct vm_area_struct **vmas = NULL;
+	struct page **pages = NULL;
+	unsigned long off, start, end, ubuf;
+	size_t size;
+	int ret, pret, nr_pages, i;
+
+	if (!iov->iov_base) {
+		*pimu = ctx->dummy_ubuf;
+		return 0;
+	}
+
+	ubuf = (unsigned long) iov->iov_base;
+	end = (ubuf + iov->iov_len + PAGE_SIZE - 1) >> PAGE_SHIFT;
+	start = ubuf >> PAGE_SHIFT;
+	nr_pages = end - start;
+
+	*pimu = NULL;
+	ret = -ENOMEM;
+
+	pages = kvmalloc_array(nr_pages, sizeof(struct page *), GFP_KERNEL);
+	if (!pages)
+		goto done;
+
+	vmas = kvmalloc_array(nr_pages, sizeof(struct vm_area_struct *),
+			      GFP_KERNEL);
+	if (!vmas)
+		goto done;
+
+	imu = kvmalloc(struct_size(imu, bvec, nr_pages), GFP_KERNEL);
+	if (!imu)
+		goto done;
+
+	ret = 0;
+	mmap_read_lock(current->mm);
+	pret = pin_user_pages(ubuf, nr_pages, FOLL_WRITE | FOLL_LONGTERM,
+			      pages, vmas);
+	if (pret == nr_pages) {
+		struct file *file = vmas[0]->vm_file;
+
+		/* don't support file backed memory */
+		for (i = 0; i < nr_pages; i++) {
+			if (vmas[i]->vm_file != file) {
+				ret = -EINVAL;
+				break;
+			}
+			if (!file)
+				continue;
+			if (!vma_is_shmem(vmas[i]) && !is_file_hugepages(file)) {
+				ret = -EOPNOTSUPP;
+				break;
+			}
+		}
+	} else {
+		ret = pret < 0 ? pret : -EFAULT;
+	}
+	mmap_read_unlock(current->mm);
+	if (ret) {
+		/*
+		 * if we did partial map, or found file backed vmas,
+		 * release any pages we did get
+		 */
+		if (pret > 0)
+			unpin_user_pages(pages, pret);
+		goto done;
+	}
+
+	ret = io_buffer_account_pin(ctx, pages, pret, imu, last_hpage);
+	if (ret) {
+		unpin_user_pages(pages, pret);
+		goto done;
+	}
+
+	off = ubuf & ~PAGE_MASK;
+	size = iov->iov_len;
+	for (i = 0; i < nr_pages; i++) {
+		size_t vec_len;
+
+		vec_len = min_t(size_t, size, PAGE_SIZE - off);
+		imu->bvec[i].bv_page = pages[i];
+		imu->bvec[i].bv_len = vec_len;
+		imu->bvec[i].bv_offset = off;
+		off = 0;
+		size -= vec_len;
+	}
+	/* store original address for later verification */
+	imu->ubuf = ubuf;
+	imu->ubuf_end = ubuf + iov->iov_len;
+	imu->nr_bvecs = nr_pages;
+	*pimu = imu;
+	ret = 0;
+done:
+	if (ret)
+		kvfree(imu);
+	kvfree(pages);
+	kvfree(vmas);
+	return ret;
+}
+
+static int io_buffers_map_alloc(struct io_ring_ctx *ctx, unsigned int nr_args)
+{
+	ctx->user_bufs = kcalloc(nr_args, sizeof(*ctx->user_bufs), GFP_KERNEL);
+	return ctx->user_bufs ? 0 : -ENOMEM;
+}
+
+static int io_buffer_validate(struct iovec *iov)
+{
+	unsigned long tmp, acct_len = iov->iov_len + (PAGE_SIZE - 1);
+
+	/*
+	 * Don't impose further limits on the size and buffer
+	 * constraints here, we'll -EINVAL later when IO is
+	 * submitted if they are wrong.
+	 */
+	if (!iov->iov_base)
+		return iov->iov_len ? -EFAULT : 0;
+	if (!iov->iov_len)
+		return -EFAULT;
+
+	/* arbitrary limit, but we need something */
+	if (iov->iov_len > SZ_1G)
+		return -EFAULT;
+
+	if (check_add_overflow((unsigned long)iov->iov_base, acct_len, &tmp))
+		return -EOVERFLOW;
+
+	return 0;
+}
+
+static int io_sqe_buffers_register(struct io_ring_ctx *ctx, void __user *arg,
+				   unsigned int nr_args, u64 __user *tags)
+{
+	struct page *last_hpage = NULL;
+	struct io_rsrc_data *data;
+	int i, ret;
+	struct iovec iov;
+
+	if (ctx->user_bufs)
+		return -EBUSY;
+	if (!nr_args || nr_args > IORING_MAX_REG_BUFFERS)
+		return -EINVAL;
+	ret = io_rsrc_node_switch_start(ctx);
+	if (ret)
+		return ret;
+	ret = io_rsrc_data_alloc(ctx, io_rsrc_buf_put, tags, nr_args, &data);
+	if (ret)
+		return ret;
+	ret = io_buffers_map_alloc(ctx, nr_args);
+	if (ret) {
+		io_rsrc_data_free(data);
+		return ret;
+	}
+
+	for (i = 0; i < nr_args; i++, ctx->nr_user_bufs++) {
+		ret = io_copy_iov(ctx, &iov, arg, i);
+		if (ret)
+			break;
+		ret = io_buffer_validate(&iov);
+		if (ret)
+			break;
+		if (!iov.iov_base && *io_get_tag_slot(data, i)) {
+			ret = -EINVAL;
+			break;
+		}
+
+		ret = io_sqe_buffer_register(ctx, &iov, &ctx->user_bufs[i],
+					     &last_hpage);
+		if (ret)
+			break;
+	}
+
+	WARN_ON_ONCE(ctx->buf_data);
+
+	ctx->buf_data = data;
+	if (ret)
+		__io_sqe_buffers_unregister(ctx);
+	else
+		io_rsrc_node_switch(ctx, NULL);
+	return ret;
+}
+
+static int __io_sqe_buffers_update(struct io_ring_ctx *ctx,
+				   struct io_uring_rsrc_update2 *up,
+				   unsigned int nr_args)
+{
+	u64 __user *tags = u64_to_user_ptr(up->tags);
+	struct iovec iov, __user *iovs = u64_to_user_ptr(up->data);
+	struct page *last_hpage = NULL;
+	bool needs_switch = false;
+	__u32 done;
+	int i, err;
+
+	if (!ctx->buf_data)
+		return -ENXIO;
+	if (up->offset + nr_args > ctx->nr_user_bufs)
+		return -EINVAL;
+
+	for (done = 0; done < nr_args; done++) {
+		struct io_mapped_ubuf *imu;
+		int offset = up->offset + done;
+		u64 tag = 0;
+
+		err = io_copy_iov(ctx, &iov, iovs, done);
+		if (err)
+			break;
+		if (tags && copy_from_user(&tag, &tags[done], sizeof(tag))) {
+			err = -EFAULT;
+			break;
+		}
+		err = io_buffer_validate(&iov);
+		if (err)
+			break;
+		if (!iov.iov_base && tag) {
+			err = -EINVAL;
+			break;
+		}
+		err = io_sqe_buffer_register(ctx, &iov, &imu, &last_hpage);
+		if (err)
+			break;
+
+		i = array_index_nospec(offset, ctx->nr_user_bufs);
+		if (ctx->user_bufs[i] != ctx->dummy_ubuf) {
+			err = io_queue_rsrc_removal(ctx->buf_data, i,
+						    ctx->rsrc_node, ctx->user_bufs[i]);
+			if (unlikely(err)) {
+				io_buffer_unmap(ctx, &imu);
+				break;
+			}
+			ctx->user_bufs[i] = NULL;
+			needs_switch = true;
+		}
+
+		ctx->user_bufs[i] = imu;
+		*io_get_tag_slot(ctx->buf_data, offset) = tag;
+	}
+
+	if (needs_switch)
+		io_rsrc_node_switch(ctx, ctx->buf_data);
+	return done ? done : err;
+}
+
+static int io_eventfd_register(struct io_ring_ctx *ctx, void __user *arg)
+{
+	__s32 __user *fds = arg;
+	int fd;
+
+	if (ctx->cq_ev_fd)
+		return -EBUSY;
+
+	if (copy_from_user(&fd, fds, sizeof(*fds)))
+		return -EFAULT;
+
+	ctx->cq_ev_fd = eventfd_ctx_fdget(fd);
+	if (IS_ERR(ctx->cq_ev_fd)) {
+		int ret = PTR_ERR(ctx->cq_ev_fd);
+
+		ctx->cq_ev_fd = NULL;
+		return ret;
+	}
+
+	return 0;
+}
+
+static int io_eventfd_unregister(struct io_ring_ctx *ctx)
+{
+	if (ctx->cq_ev_fd) {
+		eventfd_ctx_put(ctx->cq_ev_fd);
+		ctx->cq_ev_fd = NULL;
+		return 0;
+	}
+
+	return -ENXIO;
+}
+
+static void io_destroy_buffers(struct io_ring_ctx *ctx)
+{
+	struct io_buffer *buf;
+	unsigned long index;
+
+	xa_for_each(&ctx->io_buffers, index, buf)
+		__io_remove_buffers(ctx, buf, index, -1U);
+}
+
+static void io_req_cache_free(struct list_head *list)
+{
+	struct io_kiocb *req, *nxt;
+
+	list_for_each_entry_safe(req, nxt, list, inflight_entry) {
+		list_del(&req->inflight_entry);
+		kmem_cache_free(req_cachep, req);
+	}
+}
+
+static void io_req_caches_free(struct io_ring_ctx *ctx)
+{
+	struct io_submit_state *state = &ctx->submit_state;
+
+	mutex_lock(&ctx->uring_lock);
+
+	if (state->free_reqs) {
+		kmem_cache_free_bulk(req_cachep, state->free_reqs, state->reqs);
+		state->free_reqs = 0;
+	}
+
+	io_flush_cached_locked_reqs(ctx, state);
+	io_req_cache_free(&state->free_list);
+	mutex_unlock(&ctx->uring_lock);
+}
+
+static void io_wait_rsrc_data(struct io_rsrc_data *data)
+{
+	if (data && !atomic_dec_and_test(&data->refs))
+		wait_for_completion(&data->done);
+}
+
+static void io_ring_ctx_free(struct io_ring_ctx *ctx)
+{
+	io_sq_thread_finish(ctx);
+
+	/* __io_rsrc_put_work() may need uring_lock to progress, wait w/o it */
+	io_wait_rsrc_data(ctx->buf_data);
+	io_wait_rsrc_data(ctx->file_data);
+
+	mutex_lock(&ctx->uring_lock);
+	if (ctx->buf_data)
+		__io_sqe_buffers_unregister(ctx);
+	if (ctx->file_data)
+		__io_sqe_files_unregister(ctx);
+	if (ctx->rings)
+		__io_cqring_overflow_flush(ctx, true);
+	mutex_unlock(&ctx->uring_lock);
+	io_eventfd_unregister(ctx);
+	io_destroy_buffers(ctx);
+	if (ctx->sq_creds)
+		put_cred(ctx->sq_creds);
+
+	/* there are no registered resources left, nobody uses it */
+	if (ctx->rsrc_node)
+		io_rsrc_node_destroy(ctx->rsrc_node);
+	if (ctx->rsrc_backup_node)
+		io_rsrc_node_destroy(ctx->rsrc_backup_node);
+	flush_delayed_work(&ctx->rsrc_put_work);
+
+	WARN_ON_ONCE(!list_empty(&ctx->rsrc_ref_list));
+	WARN_ON_ONCE(!llist_empty(&ctx->rsrc_put_llist));
+
+	WARN_ON_ONCE(!list_empty(&ctx->ltimeout_list));
+
+	if (ctx->mm_account) {
+		mmdrop(ctx->mm_account);
+		ctx->mm_account = NULL;
+	}
+
+	io_mem_free(ctx->rings);
+	io_mem_free(ctx->sq_sqes);
+
+	percpu_ref_exit(&ctx->refs);
+	free_uid(ctx->user);
+	io_req_caches_free(ctx);
+	if (ctx->hash_map)
+		io_wq_put_hash(ctx->hash_map);
+	kfree(ctx->cancel_hash);
+	kfree(ctx->dummy_ubuf);
+	kfree(ctx);
+}
+
+static __poll_t io_uring_poll(struct file *file, poll_table *wait)
+{
+	struct io_ring_ctx *ctx = file->private_data;
+	__poll_t mask = 0;
+
+	poll_wait(file, &ctx->poll_wait, wait);
+	/*
+	 * synchronizes with barrier from wq_has_sleeper call in
+	 * io_commit_cqring
+	 */
+	smp_rmb();
+	if (!io_sqring_full(ctx))
+		mask |= EPOLLOUT | EPOLLWRNORM;
+
+	/*
+	 * Don't flush cqring overflow list here, just do a simple check.
+	 * Otherwise there could possible be ABBA deadlock:
+	 *      CPU0                    CPU1
+	 *      ----                    ----
+	 * lock(&ctx->uring_lock);
+	 *                              lock(&ep->mtx);
+	 *                              lock(&ctx->uring_lock);
+	 * lock(&ep->mtx);
+	 *
+	 * Users may get EPOLLIN meanwhile seeing nothing in cqring, this
+	 * pushs them to do the flush.
+	 */
+	if (io_cqring_events(ctx) || test_bit(0, &ctx->check_cq_overflow))
+		mask |= EPOLLIN | EPOLLRDNORM;
+
+	return mask;
+}
+
+static int io_unregister_personality(struct io_ring_ctx *ctx, unsigned id)
+{
+	const struct cred *creds;
+
+	creds = xa_erase(&ctx->personalities, id);
+	if (creds) {
+		put_cred(creds);
+		return 0;
+	}
+
+	return -EINVAL;
+}
+
+struct io_tctx_exit {
+	struct callback_head		task_work;
+	struct completion		completion;
+	struct io_ring_ctx		*ctx;
+};
+
+static void io_tctx_exit_cb(struct callback_head *cb)
+{
+	struct io_uring_task *tctx = current->io_uring;
+	struct io_tctx_exit *work;
+
+	work = container_of(cb, struct io_tctx_exit, task_work);
+	/*
+	 * When @in_idle, we're in cancellation and it's racy to remove the
+	 * node. It'll be removed by the end of cancellation, just ignore it.
+	 * tctx can be NULL if the queueing of this task_work raced with
+	 * work cancelation off the exec path.
+	 */
+	if (tctx && !atomic_read(&tctx->in_idle))
+		io_uring_del_tctx_node((unsigned long)work->ctx);
+	complete(&work->completion);
+}
+
+static bool io_cancel_ctx_cb(struct io_wq_work *work, void *data)
+{
+	struct io_kiocb *req = container_of(work, struct io_kiocb, work);
+
+	return req->ctx == data;
+}
+
+static void io_ring_exit_work(struct work_struct *work)
+{
+	struct io_ring_ctx *ctx = container_of(work, struct io_ring_ctx, exit_work);
+	unsigned long timeout = jiffies + HZ * 60 * 5;
+	unsigned long interval = HZ / 20;
+	struct io_tctx_exit exit;
+	struct io_tctx_node *node;
+	int ret;
+
+	/*
+	 * If we're doing polled IO and end up having requests being
+	 * submitted async (out-of-line), then completions can come in while
+	 * we're waiting for refs to drop. We need to reap these manually,
+	 * as nobody else will be looking for them.
+	 */
+	do {
+		io_uring_try_cancel_requests(ctx, NULL, true);
+		if (ctx->sq_data) {
+			struct io_sq_data *sqd = ctx->sq_data;
+			struct task_struct *tsk;
+
+			io_sq_thread_park(sqd);
+			tsk = sqd->thread;
+			if (tsk && tsk->io_uring && tsk->io_uring->io_wq)
+				io_wq_cancel_cb(tsk->io_uring->io_wq,
+						io_cancel_ctx_cb, ctx, true);
+			io_sq_thread_unpark(sqd);
+		}
+
+		if (WARN_ON_ONCE(time_after(jiffies, timeout))) {
+			/* there is little hope left, don't run it too often */
+			interval = HZ * 60;
+		}
+		/*
+		 * This is really an uninterruptible wait, as it has to be
+		 * complete. But it's also run from a kworker, which doesn't
+		 * take signals, so it's fine to make it interruptible. This
+		 * avoids scenarios where we knowingly can wait much longer
+		 * on completions, for example if someone does a SIGSTOP on
+		 * a task that needs to finish task_work to make this loop
+		 * complete. That's a synthetic situation that should not
+		 * cause a stuck task backtrace, and hence a potential panic
+		 * on stuck tasks if that is enabled.
+		 */
+	} while (!wait_for_completion_interruptible_timeout(&ctx->ref_comp, interval));
+
+	init_completion(&exit.completion);
+	init_task_work(&exit.task_work, io_tctx_exit_cb);
+	exit.ctx = ctx;
+
+	mutex_lock(&ctx->uring_lock);
+	while (!list_empty(&ctx->tctx_list)) {
+		WARN_ON_ONCE(time_after(jiffies, timeout));
+
+		node = list_first_entry(&ctx->tctx_list, struct io_tctx_node,
+					ctx_node);
+		/* don't spin on a single task if cancellation failed */
+		list_rotate_left(&ctx->tctx_list);
+		ret = task_work_add(node->task, &exit.task_work, TWA_SIGNAL);
+		if (WARN_ON_ONCE(ret))
+			continue;
+		wake_up_process(node->task);
+
+		mutex_unlock(&ctx->uring_lock);
+		/*
+		 * See comment above for
+		 * wait_for_completion_interruptible_timeout() on why this
+		 * wait is marked as interruptible.
+		 */
+		wait_for_completion_interruptible(&exit.completion);
+		mutex_lock(&ctx->uring_lock);
+	}
+	mutex_unlock(&ctx->uring_lock);
+	spin_lock(&ctx->completion_lock);
+	spin_unlock(&ctx->completion_lock);
+
+	io_ring_ctx_free(ctx);
+}
+
+/* Returns true if we found and killed one or more timeouts */
+static bool io_kill_timeouts(struct io_ring_ctx *ctx, struct task_struct *tsk,
+			     bool cancel_all)
+{
+	struct io_kiocb *req, *tmp;
+	int canceled = 0;
+
+	spin_lock(&ctx->completion_lock);
+	spin_lock_irq(&ctx->timeout_lock);
+	list_for_each_entry_safe(req, tmp, &ctx->timeout_list, timeout.list) {
+		if (io_match_task(req, tsk, cancel_all)) {
+			io_kill_timeout(req, -ECANCELED);
+			canceled++;
+		}
+	}
+	spin_unlock_irq(&ctx->timeout_lock);
+	if (canceled != 0)
+		io_commit_cqring(ctx);
+	spin_unlock(&ctx->completion_lock);
+	if (canceled != 0)
+		io_cqring_ev_posted(ctx);
+	return canceled != 0;
+}
+
+static void io_ring_ctx_wait_and_kill(struct io_ring_ctx *ctx)
+{
+	unsigned long index;
+	struct creds *creds;
+
+	mutex_lock(&ctx->uring_lock);
+	percpu_ref_kill(&ctx->refs);
+	if (ctx->rings)
+		__io_cqring_overflow_flush(ctx, true);
+	xa_for_each(&ctx->personalities, index, creds)
+		io_unregister_personality(ctx, index);
+	mutex_unlock(&ctx->uring_lock);
+
+	io_kill_timeouts(ctx, NULL, true);
+	io_poll_remove_all(ctx, NULL, true);
+
+	/* if we failed setting up the ctx, we might not have any rings */
+	io_iopoll_try_reap_events(ctx);
+
+	/* drop cached put refs after potentially doing completions */
+	if (current->io_uring)
+		io_uring_drop_tctx_refs(current);
+
+	INIT_WORK(&ctx->exit_work, io_ring_exit_work);
+	/*
+	 * Use system_unbound_wq to avoid spawning tons of event kworkers
+	 * if we're exiting a ton of rings at the same time. It just adds
+	 * noise and overhead, there's no discernable change in runtime
+	 * over using system_wq.
+	 */
+	queue_work(system_unbound_wq, &ctx->exit_work);
+}
+
+static int io_uring_release(struct inode *inode, struct file *file)
+{
+	struct io_ring_ctx *ctx = file->private_data;
+
+	file->private_data = NULL;
+	io_ring_ctx_wait_and_kill(ctx);
+	return 0;
+}
+
+struct io_task_cancel {
+	struct task_struct *task;
+	bool all;
+};
+
+static bool io_cancel_task_cb(struct io_wq_work *work, void *data)
+{
+	struct io_kiocb *req = container_of(work, struct io_kiocb, work);
+	struct io_task_cancel *cancel = data;
+
+	return io_match_task_safe(req, cancel->task, cancel->all);
+}
+
+static bool io_cancel_defer_files(struct io_ring_ctx *ctx,
+				  struct task_struct *task, bool cancel_all)
+{
+	struct io_defer_entry *de;
+	LIST_HEAD(list);
+
+	spin_lock(&ctx->completion_lock);
+	list_for_each_entry_reverse(de, &ctx->defer_list, list) {
+		if (io_match_task_safe(de->req, task, cancel_all)) {
+			list_cut_position(&list, &ctx->defer_list, &de->list);
+			break;
+		}
+	}
+	spin_unlock(&ctx->completion_lock);
+	if (list_empty(&list))
+		return false;
+
+	while (!list_empty(&list)) {
+		de = list_first_entry(&list, struct io_defer_entry, list);
+		list_del_init(&de->list);
+		io_req_complete_failed(de->req, -ECANCELED);
+		kfree(de);
+	}
+	return true;
+}
+
+static bool io_uring_try_cancel_iowq(struct io_ring_ctx *ctx)
+{
+	struct io_tctx_node *node;
+	enum io_wq_cancel cret;
+	bool ret = false;
+
+	mutex_lock(&ctx->uring_lock);
+	list_for_each_entry(node, &ctx->tctx_list, ctx_node) {
+		struct io_uring_task *tctx = node->task->io_uring;
+
+		/*
+		 * io_wq will stay alive while we hold uring_lock, because it's
+		 * killed after ctx nodes, which requires to take the lock.
+		 */
+		if (!tctx || !tctx->io_wq)
+			continue;
+		cret = io_wq_cancel_cb(tctx->io_wq, io_cancel_ctx_cb, ctx, true);
+		ret |= (cret != IO_WQ_CANCEL_NOTFOUND);
+	}
+	mutex_unlock(&ctx->uring_lock);
+
+	return ret;
+}
+
+static void io_uring_try_cancel_requests(struct io_ring_ctx *ctx,
+					 struct task_struct *task,
+					 bool cancel_all)
+{
+	struct io_task_cancel cancel = { .task = task, .all = cancel_all, };
+	struct io_uring_task *tctx = task ? task->io_uring : NULL;
+
+	while (1) {
+		enum io_wq_cancel cret;
+		bool ret = false;
+
+		if (!task) {
+			ret |= io_uring_try_cancel_iowq(ctx);
+		} else if (tctx && tctx->io_wq) {
+			/*
+			 * Cancels requests of all rings, not only @ctx, but
+			 * it's fine as the task is in exit/exec.
+			 */
+			cret = io_wq_cancel_cb(tctx->io_wq, io_cancel_task_cb,
+					       &cancel, true);
+			ret |= (cret != IO_WQ_CANCEL_NOTFOUND);
+		}
+
+		/* SQPOLL thread does its own polling */
+		if ((!(ctx->flags & IORING_SETUP_SQPOLL) && cancel_all) ||
+		    (ctx->sq_data && ctx->sq_data->thread == current)) {
+			while (!list_empty_careful(&ctx->iopoll_list)) {
+				io_iopoll_try_reap_events(ctx);
+				ret = true;
+				cond_resched();
+			}
+		}
+
+		ret |= io_cancel_defer_files(ctx, task, cancel_all);
+		ret |= io_poll_remove_all(ctx, task, cancel_all);
+		ret |= io_kill_timeouts(ctx, task, cancel_all);
+		if (task)
+			ret |= io_run_task_work();
+		if (!ret)
+			break;
+		cond_resched();
+	}
+}
+
+static int __io_uring_add_tctx_node(struct io_ring_ctx *ctx)
+{
+	struct io_uring_task *tctx = current->io_uring;
+	struct io_tctx_node *node;
+	int ret;
+
+	if (unlikely(!tctx)) {
+		ret = io_uring_alloc_task_context(current, ctx);
+		if (unlikely(ret))
+			return ret;
+
+		tctx = current->io_uring;
+		if (ctx->iowq_limits_set) {
+			unsigned int limits[2] = { ctx->iowq_limits[0],
+						   ctx->iowq_limits[1], };
+
+			ret = io_wq_max_workers(tctx->io_wq, limits);
+			if (ret)
+				return ret;
+		}
+	}
+	if (!xa_load(&tctx->xa, (unsigned long)ctx)) {
+		node = kmalloc(sizeof(*node), GFP_KERNEL);
+		if (!node)
+			return -ENOMEM;
+		node->ctx = ctx;
+		node->task = current;
+
+		ret = xa_err(xa_store(&tctx->xa, (unsigned long)ctx,
+					node, GFP_KERNEL));
+		if (ret) {
+			kfree(node);
+			return ret;
+		}
+
+		mutex_lock(&ctx->uring_lock);
+		list_add(&node->ctx_node, &ctx->tctx_list);
+		mutex_unlock(&ctx->uring_lock);
+	}
+	tctx->last = ctx;
+	return 0;
+}
+
+/*
+ * Note that this task has used io_uring. We use it for cancelation purposes.
+ */
+static inline int io_uring_add_tctx_node(struct io_ring_ctx *ctx)
+{
+	struct io_uring_task *tctx = current->io_uring;
+
+	if (likely(tctx && tctx->last == ctx))
+		return 0;
+	return __io_uring_add_tctx_node(ctx);
+}
+
+/*
+ * Remove this io_uring_file -> task mapping.
+ */
+static void io_uring_del_tctx_node(unsigned long index)
+{
+	struct io_uring_task *tctx = current->io_uring;
+	struct io_tctx_node *node;
+
+	if (!tctx)
+		return;
+	node = xa_erase(&tctx->xa, index);
+	if (!node)
+		return;
+
+	WARN_ON_ONCE(current != node->task);
+	WARN_ON_ONCE(list_empty(&node->ctx_node));
+
+	mutex_lock(&node->ctx->uring_lock);
+	list_del(&node->ctx_node);
+	mutex_unlock(&node->ctx->uring_lock);
+
+	if (tctx->last == node->ctx)
+		tctx->last = NULL;
+	kfree(node);
+}
+
+static void io_uring_clean_tctx(struct io_uring_task *tctx)
+{
+	struct io_wq *wq = tctx->io_wq;
+	struct io_tctx_node *node;
+	unsigned long index;
+
+	xa_for_each(&tctx->xa, index, node) {
+		io_uring_del_tctx_node(index);
+		cond_resched();
+	}
+	if (wq) {
+		/*
+		 * Must be after io_uring_del_task_file() (removes nodes under
+		 * uring_lock) to avoid race with io_uring_try_cancel_iowq().
+		 */
+		io_wq_put_and_exit(wq);
+		tctx->io_wq = NULL;
+	}
+}
+
+static s64 tctx_inflight(struct io_uring_task *tctx, bool tracked)
+{
+	if (tracked)
+		return atomic_read(&tctx->inflight_tracked);
+	return percpu_counter_sum(&tctx->inflight);
+}
+
+/*
+ * Find any io_uring ctx that this task has registered or done IO on, and cancel
+ * requests. @sqd should be not-null IFF it's an SQPOLL thread cancellation.
+ */
+static void io_uring_cancel_generic(bool cancel_all, struct io_sq_data *sqd)
+{
+	struct io_uring_task *tctx = current->io_uring;
+	struct io_ring_ctx *ctx;
+	s64 inflight;
+	DEFINE_WAIT(wait);
+
+	WARN_ON_ONCE(sqd && sqd->thread != current);
+
+	if (!current->io_uring)
+		return;
+	if (tctx->io_wq)
+		io_wq_exit_start(tctx->io_wq);
+
+	atomic_inc(&tctx->in_idle);
+	do {
+		io_uring_drop_tctx_refs(current);
+		if (!tctx_inflight(tctx, !cancel_all))
+			break;
+
+		/* read completions before cancelations */
+		inflight = tctx_inflight(tctx, false);
+		if (!inflight)
+			break;
+
+		if (!sqd) {
+			struct io_tctx_node *node;
+			unsigned long index;
+
+			xa_for_each(&tctx->xa, index, node) {
+				/* sqpoll task will cancel all its requests */
+				if (node->ctx->sq_data)
+					continue;
+				io_uring_try_cancel_requests(node->ctx, current,
+							     cancel_all);
+			}
+		} else {
+			list_for_each_entry(ctx, &sqd->ctx_list, sqd_list)
+				io_uring_try_cancel_requests(ctx, current,
+							     cancel_all);
+		}
+
+		prepare_to_wait(&tctx->wait, &wait, TASK_INTERRUPTIBLE);
+		io_run_task_work();
+		io_uring_drop_tctx_refs(current);
+
+		/*
+		 * If we've seen completions, retry without waiting. This
+		 * avoids a race where a completion comes in before we did
+		 * prepare_to_wait().
+		 */
+		if (inflight == tctx_inflight(tctx, !cancel_all))
+			schedule();
+		finish_wait(&tctx->wait, &wait);
+	} while (1);
+
+	io_uring_clean_tctx(tctx);
+	if (cancel_all) {
+		/*
+		 * We shouldn't run task_works after cancel, so just leave
+		 * ->in_idle set for normal exit.
+		 */
+		atomic_dec(&tctx->in_idle);
+		/* for exec all current's requests should be gone, kill tctx */
+		__io_uring_free(current);
+	}
+}
+
+void __io_uring_cancel(bool cancel_all)
+{
+	io_uring_cancel_generic(cancel_all, NULL);
+}
+
+static void *io_uring_validate_mmap_request(struct file *file,
+					    loff_t pgoff, size_t sz)
+{
+	struct io_ring_ctx *ctx = file->private_data;
+	loff_t offset = pgoff << PAGE_SHIFT;
+	struct page *page;
+	void *ptr;
+
+	switch (offset) {
+	case IORING_OFF_SQ_RING:
+	case IORING_OFF_CQ_RING:
+		ptr = ctx->rings;
+		break;
+	case IORING_OFF_SQES:
+		ptr = ctx->sq_sqes;
+		break;
+	default:
+		return ERR_PTR(-EINVAL);
+	}
+
+	page = virt_to_head_page(ptr);
+	if (sz > page_size(page))
+		return ERR_PTR(-EINVAL);
+
+	return ptr;
+}
+
+#ifdef CONFIG_MMU
+
+static int io_uring_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	size_t sz = vma->vm_end - vma->vm_start;
+	unsigned long pfn;
+	void *ptr;
+
+	ptr = io_uring_validate_mmap_request(file, vma->vm_pgoff, sz);
+	if (IS_ERR(ptr))
+		return PTR_ERR(ptr);
+
+	pfn = virt_to_phys(ptr) >> PAGE_SHIFT;
+	return remap_pfn_range(vma, vma->vm_start, pfn, sz, vma->vm_page_prot);
+}
+
+#else /* !CONFIG_MMU */
+
+static int io_uring_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	return vma->vm_flags & (VM_SHARED | VM_MAYSHARE) ? 0 : -EINVAL;
+}
+
+static unsigned int io_uring_nommu_mmap_capabilities(struct file *file)
+{
+	return NOMMU_MAP_DIRECT | NOMMU_MAP_READ | NOMMU_MAP_WRITE;
+}
+
+static unsigned long io_uring_nommu_get_unmapped_area(struct file *file,
+	unsigned long addr, unsigned long len,
+	unsigned long pgoff, unsigned long flags)
+{
+	void *ptr;
+
+	ptr = io_uring_validate_mmap_request(file, pgoff, len);
+	if (IS_ERR(ptr))
+		return PTR_ERR(ptr);
+
+	return (unsigned long) ptr;
+}
+
+#endif /* !CONFIG_MMU */
+
+static int io_sqpoll_wait_sq(struct io_ring_ctx *ctx)
+{
+	DEFINE_WAIT(wait);
+
+	do {
+		if (!io_sqring_full(ctx))
+			break;
+		prepare_to_wait(&ctx->sqo_sq_wait, &wait, TASK_INTERRUPTIBLE);
+
+		if (!io_sqring_full(ctx))
+			break;
+		schedule();
+	} while (!signal_pending(current));
+
+	finish_wait(&ctx->sqo_sq_wait, &wait);
+	return 0;
+}
+
+static int io_get_ext_arg(unsigned flags, const void __user *argp, size_t *argsz,
+			  struct __kernel_timespec __user **ts,
+			  const sigset_t __user **sig)
+{
+	struct io_uring_getevents_arg arg;
+
+	/*
+	 * If EXT_ARG isn't set, then we have no timespec and the argp pointer
+	 * is just a pointer to the sigset_t.
+	 */
+	if (!(flags & IORING_ENTER_EXT_ARG)) {
+		*sig = (const sigset_t __user *) argp;
+		*ts = NULL;
+		return 0;
+	}
+
+	/*
+	 * EXT_ARG is set - ensure we agree on the size of it and copy in our
+	 * timespec and sigset_t pointers if good.
+	 */
+	if (*argsz != sizeof(arg))
+		return -EINVAL;
+	if (copy_from_user(&arg, argp, sizeof(arg)))
+		return -EFAULT;
+	if (arg.pad)
+		return -EINVAL;
+	*sig = u64_to_user_ptr(arg.sigmask);
+	*argsz = arg.sigmask_sz;
+	*ts = u64_to_user_ptr(arg.ts);
+	return 0;
+}
+
+SYSCALL_DEFINE6(io_uring_enter, unsigned int, fd, u32, to_submit,
+		u32, min_complete, u32, flags, const void __user *, argp,
+		size_t, argsz)
+{
+	struct io_ring_ctx *ctx;
+	int submitted = 0;
+	struct fd f;
+	long ret;
+
+	io_run_task_work();
+
+	if (unlikely(flags & ~(IORING_ENTER_GETEVENTS | IORING_ENTER_SQ_WAKEUP |
+			       IORING_ENTER_SQ_WAIT | IORING_ENTER_EXT_ARG)))
+		return -EINVAL;
+
+	f = fdget(fd);
+	if (unlikely(!f.file))
+		return -EBADF;
+
+	ret = -EOPNOTSUPP;
+	if (unlikely(f.file->f_op != &io_uring_fops))
+		goto out_fput;
+
+	ret = -ENXIO;
+	ctx = f.file->private_data;
+	if (unlikely(!percpu_ref_tryget(&ctx->refs)))
+		goto out_fput;
+
+	ret = -EBADFD;
+	if (unlikely(ctx->flags & IORING_SETUP_R_DISABLED))
+		goto out;
+
+	/*
+	 * For SQ polling, the thread will do all submissions and completions.
+	 * Just return the requested submit count, and wake the thread if
+	 * we were asked to.
+	 */
+	ret = 0;
+	if (ctx->flags & IORING_SETUP_SQPOLL) {
+		io_cqring_overflow_flush(ctx);
+
+		if (unlikely(ctx->sq_data->thread == NULL)) {
+			ret = -EOWNERDEAD;
+			goto out;
+		}
+		if (flags & IORING_ENTER_SQ_WAKEUP)
+			wake_up(&ctx->sq_data->wait);
+		if (flags & IORING_ENTER_SQ_WAIT) {
+			ret = io_sqpoll_wait_sq(ctx);
+			if (ret)
+				goto out;
+		}
+		submitted = to_submit;
+	} else if (to_submit) {
+		ret = io_uring_add_tctx_node(ctx);
+		if (unlikely(ret))
+			goto out;
+		mutex_lock(&ctx->uring_lock);
+		submitted = io_submit_sqes(ctx, to_submit);
+		mutex_unlock(&ctx->uring_lock);
+
+		if (submitted != to_submit)
+			goto out;
+	}
+	if (flags & IORING_ENTER_GETEVENTS) {
+		const sigset_t __user *sig;
+		struct __kernel_timespec __user *ts;
+
+		ret = io_get_ext_arg(flags, argp, &argsz, &ts, &sig);
+		if (unlikely(ret))
+			goto out;
+
+		min_complete = min(min_complete, ctx->cq_entries);
+
+		/*
+		 * When SETUP_IOPOLL and SETUP_SQPOLL are both enabled, user
+		 * space applications don't need to do io completion events
+		 * polling again, they can rely on io_sq_thread to do polling
+		 * work, which can reduce cpu usage and uring_lock contention.
+		 */
+		if (ctx->flags & IORING_SETUP_IOPOLL &&
+		    !(ctx->flags & IORING_SETUP_SQPOLL)) {
+			ret = io_iopoll_check(ctx, min_complete);
+		} else {
+			ret = io_cqring_wait(ctx, min_complete, sig, argsz, ts);
+		}
+	}
+
+out:
+	percpu_ref_put(&ctx->refs);
+out_fput:
+	fdput(f);
+	return submitted ? submitted : ret;
+}
+
+#ifdef CONFIG_PROC_FS
+static int io_uring_show_cred(struct seq_file *m, unsigned int id,
+		const struct cred *cred)
+{
+	struct user_namespace *uns = seq_user_ns(m);
+	struct group_info *gi;
+	kernel_cap_t cap;
+	unsigned __capi;
+	int g;
+
+	seq_printf(m, "%5d\n", id);
+	seq_put_decimal_ull(m, "\tUid:\t", from_kuid_munged(uns, cred->uid));
+	seq_put_decimal_ull(m, "\t\t", from_kuid_munged(uns, cred->euid));
+	seq_put_decimal_ull(m, "\t\t", from_kuid_munged(uns, cred->suid));
+	seq_put_decimal_ull(m, "\t\t", from_kuid_munged(uns, cred->fsuid));
+	seq_put_decimal_ull(m, "\n\tGid:\t", from_kgid_munged(uns, cred->gid));
+	seq_put_decimal_ull(m, "\t\t", from_kgid_munged(uns, cred->egid));
+	seq_put_decimal_ull(m, "\t\t", from_kgid_munged(uns, cred->sgid));
+	seq_put_decimal_ull(m, "\t\t", from_kgid_munged(uns, cred->fsgid));
+	seq_puts(m, "\n\tGroups:\t");
+	gi = cred->group_info;
+	for (g = 0; g < gi->ngroups; g++) {
+		seq_put_decimal_ull(m, g ? " " : "",
+					from_kgid_munged(uns, gi->gid[g]));
+	}
+	seq_puts(m, "\n\tCapEff:\t");
+	cap = cred->cap_effective;
+	CAP_FOR_EACH_U32(__capi)
+		seq_put_hex_ll(m, NULL, cap.cap[CAP_LAST_U32 - __capi], 8);
+	seq_putc(m, '\n');
+	return 0;
+}
+
+static void __io_uring_show_fdinfo(struct io_ring_ctx *ctx, struct seq_file *m)
+{
+	int sq_pid = -1, sq_cpu = -1;
+	bool has_lock;
+	int i;
+
+	/*
+	 * Avoid ABBA deadlock between the seq lock and the io_uring mutex,
+	 * since fdinfo case grabs it in the opposite direction of normal use
+	 * cases. If we fail to get the lock, we just don't iterate any
+	 * structures that could be going away outside the io_uring mutex.
+	 */
+	has_lock = mutex_trylock(&ctx->uring_lock);
+
+	if (has_lock && (ctx->flags & IORING_SETUP_SQPOLL)) {
+		struct io_sq_data *sq = ctx->sq_data;
+
+		if (mutex_trylock(&sq->lock)) {
+			if (sq->thread) {
+				sq_pid = task_pid_nr(sq->thread);
+				sq_cpu = task_cpu(sq->thread);
+			}
+			mutex_unlock(&sq->lock);
+		}
+	}
+
+	seq_printf(m, "SqThread:\t%d\n", sq_pid);
+	seq_printf(m, "SqThreadCpu:\t%d\n", sq_cpu);
+	seq_printf(m, "UserFiles:\t%u\n", ctx->nr_user_files);
+	for (i = 0; has_lock && i < ctx->nr_user_files; i++) {
+		struct file *f = io_file_from_index(ctx, i);
+
+		if (f)
+			seq_printf(m, "%5u: %s\n", i, file_dentry(f)->d_iname);
+		else
+			seq_printf(m, "%5u: <none>\n", i);
+	}
+	seq_printf(m, "UserBufs:\t%u\n", ctx->nr_user_bufs);
+	for (i = 0; has_lock && i < ctx->nr_user_bufs; i++) {
+		struct io_mapped_ubuf *buf = ctx->user_bufs[i];
+		unsigned int len = buf->ubuf_end - buf->ubuf;
+
+		seq_printf(m, "%5u: 0x%llx/%u\n", i, buf->ubuf, len);
+	}
+	if (has_lock && !xa_empty(&ctx->personalities)) {
+		unsigned long index;
+		const struct cred *cred;
+
+		seq_printf(m, "Personalities:\n");
+		xa_for_each(&ctx->personalities, index, cred)
+			io_uring_show_cred(m, index, cred);
+	}
+	seq_printf(m, "PollList:\n");
+	spin_lock(&ctx->completion_lock);
+	for (i = 0; i < (1U << ctx->cancel_hash_bits); i++) {
+		struct hlist_head *list = &ctx->cancel_hash[i];
+		struct io_kiocb *req;
+
+		hlist_for_each_entry(req, list, hash_node)
+			seq_printf(m, "  op=%d, task_works=%d\n", req->opcode,
+					req->task->task_works != NULL);
+	}
+	spin_unlock(&ctx->completion_lock);
+	if (has_lock)
+		mutex_unlock(&ctx->uring_lock);
+}
+
+static void io_uring_show_fdinfo(struct seq_file *m, struct file *f)
+{
+	struct io_ring_ctx *ctx = f->private_data;
+
+	if (percpu_ref_tryget(&ctx->refs)) {
+		__io_uring_show_fdinfo(ctx, m);
+		percpu_ref_put(&ctx->refs);
+	}
+}
+#endif
+
+static const struct file_operations io_uring_fops = {
+	.release	= io_uring_release,
+	.mmap		= io_uring_mmap,
+#ifndef CONFIG_MMU
+	.get_unmapped_area = io_uring_nommu_get_unmapped_area,
+	.mmap_capabilities = io_uring_nommu_mmap_capabilities,
+#endif
+	.poll		= io_uring_poll,
+#ifdef CONFIG_PROC_FS
+	.show_fdinfo	= io_uring_show_fdinfo,
+#endif
+};
+
+bool io_is_uring_fops(struct file *file)
+{
+	return file->f_op == &io_uring_fops;
+}
+
+static int io_allocate_scq_urings(struct io_ring_ctx *ctx,
+				  struct io_uring_params *p)
+{
+	struct io_rings *rings;
+	size_t size, sq_array_offset;
+
+	/* make sure these are sane, as we already accounted them */
+	ctx->sq_entries = p->sq_entries;
+	ctx->cq_entries = p->cq_entries;
+
+	size = rings_size(p->sq_entries, p->cq_entries, &sq_array_offset);
+	if (size == SIZE_MAX)
+		return -EOVERFLOW;
+
+	rings = io_mem_alloc(size);
+	if (!rings)
+		return -ENOMEM;
+
+	ctx->rings = rings;
+	ctx->sq_array = (u32 *)((char *)rings + sq_array_offset);
+	rings->sq_ring_mask = p->sq_entries - 1;
+	rings->cq_ring_mask = p->cq_entries - 1;
+	rings->sq_ring_entries = p->sq_entries;
+	rings->cq_ring_entries = p->cq_entries;
+
+	size = array_size(sizeof(struct io_uring_sqe), p->sq_entries);
+	if (size == SIZE_MAX) {
+		io_mem_free(ctx->rings);
+		ctx->rings = NULL;
+		return -EOVERFLOW;
+	}
+
+	ctx->sq_sqes = io_mem_alloc(size);
+	if (!ctx->sq_sqes) {
+		io_mem_free(ctx->rings);
+		ctx->rings = NULL;
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static int io_uring_install_fd(struct io_ring_ctx *ctx, struct file *file)
+{
+	int ret, fd;
+
+	fd = get_unused_fd_flags(O_RDWR | O_CLOEXEC);
+	if (fd < 0)
+		return fd;
+
+	ret = io_uring_add_tctx_node(ctx);
+	if (ret) {
+		put_unused_fd(fd);
+		return ret;
+	}
+	fd_install(fd, file);
+	return fd;
+}
+
+/*
+ * Allocate an anonymous fd, this is what constitutes the application
+ * visible backing of an io_uring instance. The application mmaps this
+ * fd to gain access to the SQ/CQ ring details.
+ */
+static struct file *io_uring_get_file(struct io_ring_ctx *ctx)
+{
+	return anon_inode_getfile("[io_uring]", &io_uring_fops, ctx,
+				  O_RDWR | O_CLOEXEC);
+}
+
+static int io_uring_create(unsigned entries, struct io_uring_params *p,
+			   struct io_uring_params __user *params)
+{
+	struct io_ring_ctx *ctx;
+	struct file *file;
+	int ret;
+
+	if (!entries)
+		return -EINVAL;
+	if (entries > IORING_MAX_ENTRIES) {
+		if (!(p->flags & IORING_SETUP_CLAMP))
+			return -EINVAL;
+		entries = IORING_MAX_ENTRIES;
+	}
+
+	/*
+	 * Use twice as many entries for the CQ ring. It's possible for the
+	 * application to drive a higher depth than the size of the SQ ring,
+	 * since the sqes are only used at submission time. This allows for
+	 * some flexibility in overcommitting a bit. If the application has
+	 * set IORING_SETUP_CQSIZE, it will have passed in the desired number
+	 * of CQ ring entries manually.
+	 */
+	p->sq_entries = roundup_pow_of_two(entries);
+	if (p->flags & IORING_SETUP_CQSIZE) {
+		/*
+		 * If IORING_SETUP_CQSIZE is set, we do the same roundup
+		 * to a power-of-two, if it isn't already. We do NOT impose
+		 * any cq vs sq ring sizing.
+		 */
+		if (!p->cq_entries)
+			return -EINVAL;
+		if (p->cq_entries > IORING_MAX_CQ_ENTRIES) {
+			if (!(p->flags & IORING_SETUP_CLAMP))
+				return -EINVAL;
+			p->cq_entries = IORING_MAX_CQ_ENTRIES;
+		}
+		p->cq_entries = roundup_pow_of_two(p->cq_entries);
+		if (p->cq_entries < p->sq_entries)
+			return -EINVAL;
+	} else {
+		p->cq_entries = 2 * p->sq_entries;
+	}
+
+	ctx = io_ring_ctx_alloc(p);
+	if (!ctx)
+		return -ENOMEM;
+	ctx->compat = in_compat_syscall();
+	if (!ns_capable_noaudit(&init_user_ns, CAP_IPC_LOCK))
+		ctx->user = get_uid(current_user());
+
+	/*
+	 * This is just grabbed for accounting purposes. When a process exits,
+	 * the mm is exited and dropped before the files, hence we need to hang
+	 * on to this mm purely for the purposes of being able to unaccount
+	 * memory (locked/pinned vm). It's not used for anything else.
+	 */
+	mmgrab(current->mm);
+	ctx->mm_account = current->mm;
+
+	ret = io_allocate_scq_urings(ctx, p);
+	if (ret)
+		goto err;
+
+	ret = io_sq_offload_create(ctx, p);
+	if (ret)
+		goto err;
+	/* always set a rsrc node */
+	ret = io_rsrc_node_switch_start(ctx);
+	if (ret)
+		goto err;
+	io_rsrc_node_switch(ctx, NULL);
+
+	memset(&p->sq_off, 0, sizeof(p->sq_off));
+	p->sq_off.head = offsetof(struct io_rings, sq.head);
+	p->sq_off.tail = offsetof(struct io_rings, sq.tail);
+	p->sq_off.ring_mask = offsetof(struct io_rings, sq_ring_mask);
+	p->sq_off.ring_entries = offsetof(struct io_rings, sq_ring_entries);
+	p->sq_off.flags = offsetof(struct io_rings, sq_flags);
+	p->sq_off.dropped = offsetof(struct io_rings, sq_dropped);
+	p->sq_off.array = (char *)ctx->sq_array - (char *)ctx->rings;
+
+	memset(&p->cq_off, 0, sizeof(p->cq_off));
+	p->cq_off.head = offsetof(struct io_rings, cq.head);
+	p->cq_off.tail = offsetof(struct io_rings, cq.tail);
+	p->cq_off.ring_mask = offsetof(struct io_rings, cq_ring_mask);
+	p->cq_off.ring_entries = offsetof(struct io_rings, cq_ring_entries);
+	p->cq_off.overflow = offsetof(struct io_rings, cq_overflow);
+	p->cq_off.cqes = offsetof(struct io_rings, cqes);
+	p->cq_off.flags = offsetof(struct io_rings, cq_flags);
+
+	p->features = IORING_FEAT_SINGLE_MMAP | IORING_FEAT_NODROP |
+			IORING_FEAT_SUBMIT_STABLE | IORING_FEAT_RW_CUR_POS |
+			IORING_FEAT_CUR_PERSONALITY | IORING_FEAT_FAST_POLL |
+			IORING_FEAT_POLL_32BITS | IORING_FEAT_SQPOLL_NONFIXED |
+			IORING_FEAT_EXT_ARG | IORING_FEAT_NATIVE_WORKERS |
+			IORING_FEAT_RSRC_TAGS;
+
+	if (copy_to_user(params, p, sizeof(*p))) {
+		ret = -EFAULT;
+		goto err;
+	}
+
+	file = io_uring_get_file(ctx);
+	if (IS_ERR(file)) {
+		ret = PTR_ERR(file);
+		goto err;
+	}
+
+	/*
+	 * Install ring fd as the very last thing, so we don't risk someone
+	 * having closed it before we finish setup
+	 */
+	ret = io_uring_install_fd(ctx, file);
+	if (ret < 0) {
+		/* fput will clean it up */
+		fput(file);
+		return ret;
+	}
+
+	trace_io_uring_create(ret, ctx, p->sq_entries, p->cq_entries, p->flags);
+	return ret;
+err:
+	io_ring_ctx_wait_and_kill(ctx);
+	return ret;
+}
+
+/*
+ * Sets up an aio uring context, and returns the fd. Applications asks for a
+ * ring size, we return the actual sq/cq ring sizes (among other things) in the
+ * params structure passed in.
+ */
+static long io_uring_setup(u32 entries, struct io_uring_params __user *params)
+{
+	struct io_uring_params p;
+	int i;
+
+	if (copy_from_user(&p, params, sizeof(p)))
+		return -EFAULT;
+	for (i = 0; i < ARRAY_SIZE(p.resv); i++) {
+		if (p.resv[i])
+			return -EINVAL;
+	}
+
+	if (p.flags & ~(IORING_SETUP_IOPOLL | IORING_SETUP_SQPOLL |
+			IORING_SETUP_SQ_AFF | IORING_SETUP_CQSIZE |
+			IORING_SETUP_CLAMP | IORING_SETUP_ATTACH_WQ |
+			IORING_SETUP_R_DISABLED))
+		return -EINVAL;
+
+	return  io_uring_create(entries, &p, params);
+}
+
+static inline bool io_uring_allowed(void)
+{
+	int disabled = READ_ONCE(sysctl_io_uring_disabled);
+	kgid_t io_uring_group;
+
+	if (disabled == 2)
+		return false;
+
+	if (disabled == 0 || capable(CAP_SYS_ADMIN))
+		return true;
+
+	io_uring_group = make_kgid(&init_user_ns, sysctl_io_uring_group);
+	if (!gid_valid(io_uring_group))
+		return false;
+
+	return in_group_p(io_uring_group);
+}
+
+SYSCALL_DEFINE2(io_uring_setup, u32, entries,
+		struct io_uring_params __user *, params)
+{
+	if (!io_uring_allowed())
+		return -EPERM;
+
+	return io_uring_setup(entries, params);
+}
+
+static int io_probe(struct io_ring_ctx *ctx, void __user *arg, unsigned nr_args)
+{
+	struct io_uring_probe *p;
+	size_t size;
+	int i, ret;
+
+	size = struct_size(p, ops, nr_args);
+	if (size == SIZE_MAX)
+		return -EOVERFLOW;
+	p = kzalloc(size, GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
+	ret = -EFAULT;
+	if (copy_from_user(p, arg, size))
+		goto out;
+	ret = -EINVAL;
+	if (memchr_inv(p, 0, size))
+		goto out;
+
+	p->last_op = IORING_OP_LAST - 1;
+	if (nr_args > IORING_OP_LAST)
+		nr_args = IORING_OP_LAST;
+
+	for (i = 0; i < nr_args; i++) {
+		p->ops[i].op = i;
+		if (!io_op_defs[i].not_supported)
+			p->ops[i].flags = IO_URING_OP_SUPPORTED;
+	}
+	p->ops_len = i;
+
+	ret = 0;
+	if (copy_to_user(arg, p, size))
+		ret = -EFAULT;
+out:
+	kfree(p);
+	return ret;
+}
+
+static int io_register_personality(struct io_ring_ctx *ctx)
+{
+	const struct cred *creds;
+	u32 id;
+	int ret;
+
+	creds = get_current_cred();
+
+	ret = xa_alloc_cyclic(&ctx->personalities, &id, (void *)creds,
+			XA_LIMIT(0, USHRT_MAX), &ctx->pers_next, GFP_KERNEL);
+	if (ret < 0) {
+		put_cred(creds);
+		return ret;
+	}
+	return id;
+}
+
+static int io_register_restrictions(struct io_ring_ctx *ctx, void __user *arg,
+				    unsigned int nr_args)
+{
+	struct io_uring_restriction *res;
+	size_t size;
+	int i, ret;
+
+	/* Restrictions allowed only if rings started disabled */
+	if (!(ctx->flags & IORING_SETUP_R_DISABLED))
+		return -EBADFD;
+
+	/* We allow only a single restrictions registration */
+	if (ctx->restrictions.registered)
+		return -EBUSY;
+
+	if (!arg || nr_args > IORING_MAX_RESTRICTIONS)
+		return -EINVAL;
+
+	size = array_size(nr_args, sizeof(*res));
+	if (size == SIZE_MAX)
+		return -EOVERFLOW;
+
+	res = memdup_user(arg, size);
+	if (IS_ERR(res))
+		return PTR_ERR(res);
+
+	ret = 0;
+
+	for (i = 0; i < nr_args; i++) {
+		switch (res[i].opcode) {
+		case IORING_RESTRICTION_REGISTER_OP:
+			if (res[i].register_op >= IORING_REGISTER_LAST) {
+				ret = -EINVAL;
+				goto out;
+			}
+
+			__set_bit(res[i].register_op,
+				  ctx->restrictions.register_op);
+			break;
+		case IORING_RESTRICTION_SQE_OP:
+			if (res[i].sqe_op >= IORING_OP_LAST) {
+				ret = -EINVAL;
+				goto out;
+			}
+
+			__set_bit(res[i].sqe_op, ctx->restrictions.sqe_op);
+			break;
+		case IORING_RESTRICTION_SQE_FLAGS_ALLOWED:
+			ctx->restrictions.sqe_flags_allowed = res[i].sqe_flags;
+			break;
+		case IORING_RESTRICTION_SQE_FLAGS_REQUIRED:
+			ctx->restrictions.sqe_flags_required = res[i].sqe_flags;
+			break;
+		default:
+			ret = -EINVAL;
+			goto out;
+		}
+	}
+
+out:
+	/* Reset all restrictions if an error happened */
+	if (ret != 0)
+		memset(&ctx->restrictions, 0, sizeof(ctx->restrictions));
+	else
+		ctx->restrictions.registered = true;
+
+	kfree(res);
+	return ret;
+}
+
+static int io_register_enable_rings(struct io_ring_ctx *ctx)
+{
+	if (!(ctx->flags & IORING_SETUP_R_DISABLED))
+		return -EBADFD;
+
+	if (ctx->restrictions.registered)
+		ctx->restricted = 1;
+
+	ctx->flags &= ~IORING_SETUP_R_DISABLED;
+	if (ctx->sq_data && wq_has_sleeper(&ctx->sq_data->wait))
+		wake_up(&ctx->sq_data->wait);
+	return 0;
+}
+
+static int __io_register_rsrc_update(struct io_ring_ctx *ctx, unsigned type,
+				     struct io_uring_rsrc_update2 *up,
+				     unsigned nr_args)
+{
+	__u32 tmp;
+	int err;
+
+	if (check_add_overflow(up->offset, nr_args, &tmp))
+		return -EOVERFLOW;
+	err = io_rsrc_node_switch_start(ctx);
+	if (err)
+		return err;
+
+	switch (type) {
+	case IORING_RSRC_FILE:
+		return __io_sqe_files_update(ctx, up, nr_args);
+	case IORING_RSRC_BUFFER:
+		return __io_sqe_buffers_update(ctx, up, nr_args);
+	}
+	return -EINVAL;
+}
+
+static int io_register_files_update(struct io_ring_ctx *ctx, void __user *arg,
+				    unsigned nr_args)
+{
+	struct io_uring_rsrc_update2 up;
+
+	if (!nr_args)
+		return -EINVAL;
+	memset(&up, 0, sizeof(up));
+	if (copy_from_user(&up, arg, sizeof(struct io_uring_rsrc_update)))
+		return -EFAULT;
+	if (up.resv || up.resv2)
+		return -EINVAL;
+	return __io_register_rsrc_update(ctx, IORING_RSRC_FILE, &up, nr_args);
+}
+
+static int io_register_rsrc_update(struct io_ring_ctx *ctx, void __user *arg,
+				   unsigned size, unsigned type)
+{
+	struct io_uring_rsrc_update2 up;
+
+	if (size != sizeof(up))
+		return -EINVAL;
+	if (copy_from_user(&up, arg, sizeof(up)))
+		return -EFAULT;
+	if (!up.nr || up.resv || up.resv2)
+		return -EINVAL;
+	return __io_register_rsrc_update(ctx, type, &up, up.nr);
+}
+
+static int io_register_rsrc(struct io_ring_ctx *ctx, void __user *arg,
+			    unsigned int size, unsigned int type)
+{
+	struct io_uring_rsrc_register rr;
+
+	/* keep it extendible */
+	if (size != sizeof(rr))
+		return -EINVAL;
+
+	memset(&rr, 0, sizeof(rr));
+	if (copy_from_user(&rr, arg, size))
+		return -EFAULT;
+	if (!rr.nr || rr.resv || rr.resv2)
+		return -EINVAL;
+
+	switch (type) {
+	case IORING_RSRC_FILE:
+		return io_sqe_files_register(ctx, u64_to_user_ptr(rr.data),
+					     rr.nr, u64_to_user_ptr(rr.tags));
+	case IORING_RSRC_BUFFER:
+		return io_sqe_buffers_register(ctx, u64_to_user_ptr(rr.data),
+					       rr.nr, u64_to_user_ptr(rr.tags));
+	}
+	return -EINVAL;
+}
+
+static int io_register_iowq_aff(struct io_ring_ctx *ctx, void __user *arg,
+				unsigned len)
+{
+	struct io_uring_task *tctx = current->io_uring;
+	cpumask_var_t new_mask;
+	int ret;
+
+	if (!tctx || !tctx->io_wq)
+		return -EINVAL;
+
+	if (!alloc_cpumask_var(&new_mask, GFP_KERNEL))
+		return -ENOMEM;
+
+	cpumask_clear(new_mask);
+	if (len > cpumask_size())
+		len = cpumask_size();
+
+	if (in_compat_syscall()) {
+		ret = compat_get_bitmap(cpumask_bits(new_mask),
+					(const compat_ulong_t __user *)arg,
+					len * 8 /* CHAR_BIT */);
+	} else {
+		ret = copy_from_user(new_mask, arg, len);
+	}
+
+	if (ret) {
+		free_cpumask_var(new_mask);
+		return -EFAULT;
+	}
+
+	ret = io_wq_cpu_affinity(tctx->io_wq, new_mask);
+	free_cpumask_var(new_mask);
+	return ret;
+}
+
+static int io_unregister_iowq_aff(struct io_ring_ctx *ctx)
+{
+	struct io_uring_task *tctx = current->io_uring;
+
+	if (!tctx || !tctx->io_wq)
+		return -EINVAL;
+
+	return io_wq_cpu_affinity(tctx->io_wq, NULL);
+}
+
+static int io_register_iowq_max_workers(struct io_ring_ctx *ctx,
+					void __user *arg)
+	__must_hold(&ctx->uring_lock)
+{
+	struct io_tctx_node *node;
+	struct io_uring_task *tctx = NULL;
+	struct io_sq_data *sqd = NULL;
+	__u32 new_count[2];
+	int i, ret;
+
+	if (copy_from_user(new_count, arg, sizeof(new_count)))
+		return -EFAULT;
+	for (i = 0; i < ARRAY_SIZE(new_count); i++)
+		if (new_count[i] > INT_MAX)
+			return -EINVAL;
+
+	if (ctx->flags & IORING_SETUP_SQPOLL) {
+		sqd = ctx->sq_data;
+		if (sqd) {
+			/*
+			 * Observe the correct sqd->lock -> ctx->uring_lock
+			 * ordering. Fine to drop uring_lock here, we hold
+			 * a ref to the ctx.
+			 */
+			refcount_inc(&sqd->refs);
+			mutex_unlock(&ctx->uring_lock);
+			mutex_lock(&sqd->lock);
+			mutex_lock(&ctx->uring_lock);
+			if (sqd->thread)
+				tctx = sqd->thread->io_uring;
+		}
+	} else {
+		tctx = current->io_uring;
+	}
+
+	BUILD_BUG_ON(sizeof(new_count) != sizeof(ctx->iowq_limits));
+
+	for (i = 0; i < ARRAY_SIZE(new_count); i++)
+		if (new_count[i])
+			ctx->iowq_limits[i] = new_count[i];
+	ctx->iowq_limits_set = true;
+
+	ret = -EINVAL;
+	if (tctx && tctx->io_wq) {
+		ret = io_wq_max_workers(tctx->io_wq, new_count);
+		if (ret)
+			goto err;
+	} else {
+		memset(new_count, 0, sizeof(new_count));
+	}
+
+	if (sqd) {
+		mutex_unlock(&ctx->uring_lock);
+		mutex_unlock(&sqd->lock);
+		io_put_sq_data(sqd);
+		mutex_lock(&ctx->uring_lock);
+	}
+
+	if (copy_to_user(arg, new_count, sizeof(new_count)))
+		return -EFAULT;
+
+	/* that's it for SQPOLL, only the SQPOLL task creates requests */
+	if (sqd)
+		return 0;
+
+	/* now propagate the restriction to all registered users */
+	list_for_each_entry(node, &ctx->tctx_list, ctx_node) {
+		struct io_uring_task *tctx = node->task->io_uring;
+
+		if (WARN_ON_ONCE(!tctx->io_wq))
+			continue;
+
+		for (i = 0; i < ARRAY_SIZE(new_count); i++)
+			new_count[i] = ctx->iowq_limits[i];
+		/* ignore errors, it always returns zero anyway */
+		(void)io_wq_max_workers(tctx->io_wq, new_count);
+	}
+	return 0;
+err:
+	if (sqd) {
+		mutex_unlock(&ctx->uring_lock);
+		mutex_unlock(&sqd->lock);
+		io_put_sq_data(sqd);
+		mutex_lock(&ctx->uring_lock);
+
+	}
+	return ret;
+}
+
+static bool io_register_op_must_quiesce(int op)
+{
+	switch (op) {
+	case IORING_REGISTER_BUFFERS:
+	case IORING_UNREGISTER_BUFFERS:
+	case IORING_REGISTER_FILES:
+	case IORING_UNREGISTER_FILES:
+	case IORING_REGISTER_FILES_UPDATE:
+	case IORING_REGISTER_PROBE:
+	case IORING_REGISTER_PERSONALITY:
+	case IORING_UNREGISTER_PERSONALITY:
+	case IORING_REGISTER_FILES2:
+	case IORING_REGISTER_FILES_UPDATE2:
+	case IORING_REGISTER_BUFFERS2:
+	case IORING_REGISTER_BUFFERS_UPDATE:
+	case IORING_REGISTER_IOWQ_AFF:
+	case IORING_UNREGISTER_IOWQ_AFF:
+	case IORING_REGISTER_IOWQ_MAX_WORKERS:
+		return false;
+	default:
+		return true;
+	}
+}
+
+static int io_ctx_quiesce(struct io_ring_ctx *ctx)
+{
+	long ret;
+
+	percpu_ref_kill(&ctx->refs);
+
+	/*
+	 * Drop uring mutex before waiting for references to exit. If another
+	 * thread is currently inside io_uring_enter() it might need to grab the
+	 * uring_lock to make progress. If we hold it here across the drain
+	 * wait, then we can deadlock. It's safe to drop the mutex here, since
+	 * no new references will come in after we've killed the percpu ref.
+	 */
+	mutex_unlock(&ctx->uring_lock);
+	do {
+		ret = wait_for_completion_interruptible(&ctx->ref_comp);
+		if (!ret)
+			break;
+		ret = io_run_task_work_sig();
+	} while (ret >= 0);
+	mutex_lock(&ctx->uring_lock);
+
+	if (ret)
+		io_refs_resurrect(&ctx->refs, &ctx->ref_comp);
+	return ret;
+}
+
+static int __io_uring_register(struct io_ring_ctx *ctx, unsigned opcode,
+			       void __user *arg, unsigned nr_args)
+	__releases(ctx->uring_lock)
+	__acquires(ctx->uring_lock)
+{
+	int ret;
+
+	/*
+	 * We're inside the ring mutex, if the ref is already dying, then
+	 * someone else killed the ctx or is already going through
+	 * io_uring_register().
+	 */
+	if (percpu_ref_is_dying(&ctx->refs))
+		return -ENXIO;
+
+	if (ctx->restricted) {
+		opcode = array_index_nospec(opcode, IORING_REGISTER_LAST);
+		if (!test_bit(opcode, ctx->restrictions.register_op))
+			return -EACCES;
+	}
+
+	if (io_register_op_must_quiesce(opcode)) {
+		ret = io_ctx_quiesce(ctx);
+		if (ret)
+			return ret;
+	}
+
+	switch (opcode) {
+	case IORING_REGISTER_BUFFERS:
+		ret = io_sqe_buffers_register(ctx, arg, nr_args, NULL);
+		break;
+	case IORING_UNREGISTER_BUFFERS:
+		ret = -EINVAL;
+		if (arg || nr_args)
+			break;
+		ret = io_sqe_buffers_unregister(ctx);
+		break;
+	case IORING_REGISTER_FILES:
+		ret = io_sqe_files_register(ctx, arg, nr_args, NULL);
+		break;
+	case IORING_UNREGISTER_FILES:
+		ret = -EINVAL;
+		if (arg || nr_args)
+			break;
+		ret = io_sqe_files_unregister(ctx);
+		break;
+	case IORING_REGISTER_FILES_UPDATE:
+		ret = io_register_files_update(ctx, arg, nr_args);
+		break;
+	case IORING_REGISTER_EVENTFD:
+	case IORING_REGISTER_EVENTFD_ASYNC:
+		ret = -EINVAL;
+		if (nr_args != 1)
+			break;
+		ret = io_eventfd_register(ctx, arg);
+		if (ret)
+			break;
+		if (opcode == IORING_REGISTER_EVENTFD_ASYNC)
+			ctx->eventfd_async = 1;
+		else
+			ctx->eventfd_async = 0;
+		break;
+	case IORING_UNREGISTER_EVENTFD:
+		ret = -EINVAL;
+		if (arg || nr_args)
+			break;
+		ret = io_eventfd_unregister(ctx);
+		break;
+	case IORING_REGISTER_PROBE:
+		ret = -EINVAL;
+		if (!arg || nr_args > 256)
+			break;
+		ret = io_probe(ctx, arg, nr_args);
+		break;
+	case IORING_REGISTER_PERSONALITY:
+		ret = -EINVAL;
+		if (arg || nr_args)
+			break;
+		ret = io_register_personality(ctx);
+		break;
+	case IORING_UNREGISTER_PERSONALITY:
+		ret = -EINVAL;
+		if (arg)
+			break;
+		ret = io_unregister_personality(ctx, nr_args);
+		break;
+	case IORING_REGISTER_ENABLE_RINGS:
+		ret = -EINVAL;
+		if (arg || nr_args)
+			break;
+		ret = io_register_enable_rings(ctx);
+		break;
+	case IORING_REGISTER_RESTRICTIONS:
+		ret = io_register_restrictions(ctx, arg, nr_args);
+		break;
+	case IORING_REGISTER_FILES2:
+		ret = io_register_rsrc(ctx, arg, nr_args, IORING_RSRC_FILE);
+		break;
+	case IORING_REGISTER_FILES_UPDATE2:
+		ret = io_register_rsrc_update(ctx, arg, nr_args,
+					      IORING_RSRC_FILE);
+		break;
+	case IORING_REGISTER_BUFFERS2:
+		ret = io_register_rsrc(ctx, arg, nr_args, IORING_RSRC_BUFFER);
+		break;
+	case IORING_REGISTER_BUFFERS_UPDATE:
+		ret = io_register_rsrc_update(ctx, arg, nr_args,
+					      IORING_RSRC_BUFFER);
+		break;
+	case IORING_REGISTER_IOWQ_AFF:
+		ret = -EINVAL;
+		if (!arg || !nr_args)
+			break;
+		ret = io_register_iowq_aff(ctx, arg, nr_args);
+		break;
+	case IORING_UNREGISTER_IOWQ_AFF:
+		ret = -EINVAL;
+		if (arg || nr_args)
+			break;
+		ret = io_unregister_iowq_aff(ctx);
+		break;
+	case IORING_REGISTER_IOWQ_MAX_WORKERS:
+		ret = -EINVAL;
+		if (!arg || nr_args != 2)
+			break;
+		ret = io_register_iowq_max_workers(ctx, arg);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	if (io_register_op_must_quiesce(opcode)) {
+		/* bring the ctx back to life */
+		percpu_ref_reinit(&ctx->refs);
+		reinit_completion(&ctx->ref_comp);
+	}
+	return ret;
+}
+
+SYSCALL_DEFINE4(io_uring_register, unsigned int, fd, unsigned int, opcode,
+		void __user *, arg, unsigned int, nr_args)
+{
+	struct io_ring_ctx *ctx;
+	long ret = -EBADF;
+	struct fd f;
+
+	if (opcode >= IORING_REGISTER_LAST)
+		return -EINVAL;
+
+	f = fdget(fd);
+	if (!f.file)
+		return -EBADF;
+
+	ret = -EOPNOTSUPP;
+	if (f.file->f_op != &io_uring_fops)
+		goto out_fput;
+
+	ctx = f.file->private_data;
+
+	io_run_task_work();
+
+	mutex_lock(&ctx->uring_lock);
+	ret = __io_uring_register(ctx, opcode, arg, nr_args);
+	mutex_unlock(&ctx->uring_lock);
+	trace_io_uring_register(ctx, opcode, ctx->nr_user_files, ctx->nr_user_bufs,
+							ctx->cq_ev_fd != NULL, ret);
+out_fput:
+	fdput(f);
+	return ret;
+}
+
+static int __init io_uring_init(void)
+{
+#define __BUILD_BUG_VERIFY_ELEMENT(stype, eoffset, etype, ename) do { \
+	BUILD_BUG_ON(offsetof(stype, ename) != eoffset); \
+	BUILD_BUG_ON(sizeof(etype) != sizeof_field(stype, ename)); \
+} while (0)
+
+#define BUILD_BUG_SQE_ELEM(eoffset, etype, ename) \
+	__BUILD_BUG_VERIFY_ELEMENT(struct io_uring_sqe, eoffset, etype, ename)
+	BUILD_BUG_ON(sizeof(struct io_uring_sqe) != 64);
+	BUILD_BUG_SQE_ELEM(0,  __u8,   opcode);
+	BUILD_BUG_SQE_ELEM(1,  __u8,   flags);
+	BUILD_BUG_SQE_ELEM(2,  __u16,  ioprio);
+	BUILD_BUG_SQE_ELEM(4,  __s32,  fd);
+	BUILD_BUG_SQE_ELEM(8,  __u64,  off);
+	BUILD_BUG_SQE_ELEM(8,  __u64,  addr2);
+	BUILD_BUG_SQE_ELEM(16, __u64,  addr);
+	BUILD_BUG_SQE_ELEM(16, __u64,  splice_off_in);
+	BUILD_BUG_SQE_ELEM(24, __u32,  len);
+	BUILD_BUG_SQE_ELEM(28,     __kernel_rwf_t, rw_flags);
+	BUILD_BUG_SQE_ELEM(28, /* compat */   int, rw_flags);
+	BUILD_BUG_SQE_ELEM(28, /* compat */ __u32, rw_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  fsync_flags);
+	BUILD_BUG_SQE_ELEM(28, /* compat */ __u16,  poll_events);
+	BUILD_BUG_SQE_ELEM(28, __u32,  poll32_events);
+	BUILD_BUG_SQE_ELEM(28, __u32,  sync_range_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  msg_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  timeout_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  accept_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  cancel_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  open_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  statx_flags);
+	BUILD_BUG_SQE_ELEM(28, __u32,  fadvise_advice);
+	BUILD_BUG_SQE_ELEM(28, __u32,  splice_flags);
+	BUILD_BUG_SQE_ELEM(32, __u64,  user_data);
+	BUILD_BUG_SQE_ELEM(40, __u16,  buf_index);
+	BUILD_BUG_SQE_ELEM(40, __u16,  buf_group);
+	BUILD_BUG_SQE_ELEM(42, __u16,  personality);
+	BUILD_BUG_SQE_ELEM(44, __s32,  splice_fd_in);
+	BUILD_BUG_SQE_ELEM(44, __u32,  file_index);
+
+	BUILD_BUG_ON(sizeof(struct io_uring_files_update) !=
+		     sizeof(struct io_uring_rsrc_update));
+	BUILD_BUG_ON(sizeof(struct io_uring_rsrc_update) >
+		     sizeof(struct io_uring_rsrc_update2));
+
+	/* ->buf_index is u16 */
+	BUILD_BUG_ON(IORING_MAX_REG_BUFFERS >= (1u << 16));
+
+	/* should fit into one byte */
+	BUILD_BUG_ON(SQE_VALID_FLAGS >= (1 << 8));
+
+	BUILD_BUG_ON(ARRAY_SIZE(io_op_defs) != IORING_OP_LAST);
+	BUILD_BUG_ON(__REQ_F_LAST_BIT > 8 * sizeof(int));
+
+	req_cachep = KMEM_CACHE(io_kiocb, SLAB_HWCACHE_ALIGN | SLAB_PANIC |
+				SLAB_ACCOUNT);
+
+#ifdef CONFIG_SYSCTL
+	register_sysctl_init("kernel", kernel_io_uring_disabled_table);
+#endif
+
+	return 0;
+};
+__initcall(io_uring_init);
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/ipc_sysctl.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/ipc_sysctl.c
@@ -10,46 +10,20 @@
 #include <linux/nsproxy.h>
 #include <linux/sysctl.h>
 #include <linux/uaccess.h>
+#include <linux/capability.h>
 #include <linux/ipc_namespace.h>
 #include <linux/msg.h>
+#include <linux/slab.h>
 #include "util.h"
 
-static void *get_ipc(struct ctl_table *table)
-{
-	char *which = table->data;
-	struct ipc_namespace *ipc_ns = current->nsproxy->ipc_ns;
-	which = (which - (char *)&init_ipc_ns) + (char *)ipc_ns;
-	return which;
-}
-
-#ifdef CONFIG_PROC_SYSCTL
-static int proc_ipc_dointvec(struct ctl_table *table, int write,
-		void *buffer, size_t *lenp, loff_t *ppos)
-{
-	struct ctl_table ipc_table;
-
-	memcpy(&ipc_table, table, sizeof(ipc_table));
-	ipc_table.data = get_ipc(table);
-
-	return proc_dointvec(&ipc_table, write, buffer, lenp, ppos);
-}
-
-static int proc_ipc_dointvec_minmax(struct ctl_table *table, int write,
-		void *buffer, size_t *lenp, loff_t *ppos)
-{
-	struct ctl_table ipc_table;
-
-	memcpy(&ipc_table, table, sizeof(ipc_table));
-	ipc_table.data = get_ipc(table);
-
-	return proc_dointvec_minmax(&ipc_table, write, buffer, lenp, ppos);
-}
-
 static int proc_ipc_dointvec_minmax_orphans(struct ctl_table *table, int write,
 		void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct ipc_namespace *ns = current->nsproxy->ipc_ns;
-	int err = proc_ipc_dointvec_minmax(table, write, buffer, lenp, ppos);
+	struct ipc_namespace *ns =
+		container_of(table->data, struct ipc_namespace, shm_rmid_forced);
+	int err;
+
+	err = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
 
 	if (err < 0)
 		return err;
@@ -58,17 +32,6 @@
 	return err;
 }
 
-static int proc_ipc_doulongvec_minmax(struct ctl_table *table, int write,
-		void *buffer, size_t *lenp, loff_t *ppos)
-{
-	struct ctl_table ipc_table;
-	memcpy(&ipc_table, table, sizeof(ipc_table));
-	ipc_table.data = get_ipc(table);
-
-	return proc_doulongvec_minmax(&ipc_table, write, buffer,
-					lenp, ppos);
-}
-
 static int proc_ipc_auto_msgmni(struct ctl_table *table, int write,
 		void *buffer, size_t *lenp, loff_t *ppos)
 {
@@ -87,14 +50,15 @@
 static int proc_ipc_sem_dointvec(struct ctl_table *table, int write,
 	void *buffer, size_t *lenp, loff_t *ppos)
 {
+	struct ipc_namespace *ns =
+		container_of(table->data, struct ipc_namespace, sem_ctls);
 	int ret, semmni;
-	struct ipc_namespace *ns = current->nsproxy->ipc_ns;
 
 	semmni = ns->sem_ctls[3];
-	ret = proc_ipc_dointvec(table, write, buffer, lenp, ppos);
+	ret = proc_dointvec(table, write, buffer, lenp, ppos);
 
 	if (!ret)
-		ret = sem_check_semmni(current->nsproxy->ipc_ns);
+		ret = sem_check_semmni(ns);
 
 	/*
 	 * Reset the semmni value if an error happens.
@@ -104,40 +68,31 @@
 	return ret;
 }
 
-#else
-#define proc_ipc_doulongvec_minmax NULL
-#define proc_ipc_dointvec	   NULL
-#define proc_ipc_dointvec_minmax   NULL
-#define proc_ipc_dointvec_minmax_orphans   NULL
-#define proc_ipc_auto_msgmni	   NULL
-#define proc_ipc_sem_dointvec	   NULL
-#endif
-
 int ipc_mni = IPCMNI;
 int ipc_mni_shift = IPCMNI_SHIFT;
 int ipc_min_cycle = RADIX_TREE_MAP_SIZE;
 
-static struct ctl_table ipc_kern_table[] = {
+static struct ctl_table ipc_sysctls[] = {
 	{
 		.procname	= "shmmax",
 		.data		= &init_ipc_ns.shm_ctlmax,
 		.maxlen		= sizeof(init_ipc_ns.shm_ctlmax),
 		.mode		= 0644,
-		.proc_handler	= proc_ipc_doulongvec_minmax,
+		.proc_handler	= proc_doulongvec_minmax,
 	},
 	{
 		.procname	= "shmall",
 		.data		= &init_ipc_ns.shm_ctlall,
 		.maxlen		= sizeof(init_ipc_ns.shm_ctlall),
 		.mode		= 0644,
-		.proc_handler	= proc_ipc_doulongvec_minmax,
+		.proc_handler	= proc_doulongvec_minmax,
 	},
 	{
 		.procname	= "shmmni",
 		.data		= &init_ipc_ns.shm_ctlmni,
 		.maxlen		= sizeof(init_ipc_ns.shm_ctlmni),
 		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= &ipc_mni,
 	},
@@ -155,7 +110,7 @@
 		.data		= &init_ipc_ns.msg_ctlmax,
 		.maxlen		= sizeof(init_ipc_ns.msg_ctlmax),
 		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= SYSCTL_INT_MAX,
 	},
@@ -164,7 +119,7 @@
 		.data		= &init_ipc_ns.msg_ctlmni,
 		.maxlen		= sizeof(init_ipc_ns.msg_ctlmni),
 		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= &ipc_mni,
 	},
@@ -182,7 +137,7 @@
 		.data		= &init_ipc_ns.msg_ctlmnb,
 		.maxlen		= sizeof(init_ipc_ns.msg_ctlmnb),
 		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= SYSCTL_INT_MAX,
 	},
@@ -198,8 +153,8 @@
 		.procname	= "sem_next_id",
 		.data		= &init_ipc_ns.ids[IPC_SEM_IDS].next_id,
 		.maxlen		= sizeof(init_ipc_ns.ids[IPC_SEM_IDS].next_id),
-		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.mode		= 0444,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= SYSCTL_INT_MAX,
 	},
@@ -207,8 +162,8 @@
 		.procname	= "msg_next_id",
 		.data		= &init_ipc_ns.ids[IPC_MSG_IDS].next_id,
 		.maxlen		= sizeof(init_ipc_ns.ids[IPC_MSG_IDS].next_id),
-		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.mode		= 0444,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= SYSCTL_INT_MAX,
 	},
@@ -216,8 +171,8 @@
 		.procname	= "shm_next_id",
 		.data		= &init_ipc_ns.ids[IPC_SHM_IDS].next_id,
 		.maxlen		= sizeof(init_ipc_ns.ids[IPC_SHM_IDS].next_id),
-		.mode		= 0644,
-		.proc_handler	= proc_ipc_dointvec_minmax,
+		.mode		= 0444,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
 		.extra2		= SYSCTL_INT_MAX,
 	},
@@ -225,18 +180,113 @@
 	{}
 };
 
-static struct ctl_table ipc_root_table[] = {
-	{
-		.procname	= "kernel",
-		.mode		= 0555,
-		.child		= ipc_kern_table,
-	},
-	{}
+static struct ctl_table_set *set_lookup(struct ctl_table_root *root)
+{
+	return &current->nsproxy->ipc_ns->ipc_set;
+}
+
+static int set_is_seen(struct ctl_table_set *set)
+{
+	return &current->nsproxy->ipc_ns->ipc_set == set;
+}
+
+static int ipc_permissions(struct ctl_table_header *head, struct ctl_table *table)
+{
+	int mode = table->mode;
+
+#ifdef CONFIG_CHECKPOINT_RESTORE
+	struct ipc_namespace *ns = current->nsproxy->ipc_ns;
+
+	if (((table->data == &ns->ids[IPC_SEM_IDS].next_id) ||
+	     (table->data == &ns->ids[IPC_MSG_IDS].next_id) ||
+	     (table->data == &ns->ids[IPC_SHM_IDS].next_id)) &&
+	    checkpoint_restore_ns_capable(ns->user_ns))
+		mode = 0666;
+#endif
+	return mode;
+}
+
+static struct ctl_table_root set_root = {
+	.lookup = set_lookup,
+	.permissions = ipc_permissions,
 };
 
+bool setup_ipc_sysctls(struct ipc_namespace *ns)
+{
+	struct ctl_table *tbl;
+
+	setup_sysctl_set(&ns->ipc_set, &set_root, set_is_seen);
+
+	tbl = kmemdup(ipc_sysctls, sizeof(ipc_sysctls), GFP_KERNEL);
+	if (tbl) {
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(ipc_sysctls); i++) {
+			if (tbl[i].data == &init_ipc_ns.shm_ctlmax) {
+				tbl[i].data = &ns->shm_ctlmax;
+
+			} else if (tbl[i].data == &init_ipc_ns.shm_ctlall) {
+				tbl[i].data = &ns->shm_ctlall;
+
+			} else if (tbl[i].data == &init_ipc_ns.shm_ctlmni) {
+				tbl[i].data = &ns->shm_ctlmni;
+
+			} else if (tbl[i].data == &init_ipc_ns.shm_rmid_forced) {
+				tbl[i].data = &ns->shm_rmid_forced;
+
+			} else if (tbl[i].data == &init_ipc_ns.msg_ctlmax) {
+				tbl[i].data = &ns->msg_ctlmax;
+
+			} else if (tbl[i].data == &init_ipc_ns.msg_ctlmni) {
+				tbl[i].data = &ns->msg_ctlmni;
+
+			} else if (tbl[i].data == &init_ipc_ns.msg_ctlmnb) {
+				tbl[i].data = &ns->msg_ctlmnb;
+
+			} else if (tbl[i].data == &init_ipc_ns.sem_ctls) {
+				tbl[i].data = &ns->sem_ctls;
+#ifdef CONFIG_CHECKPOINT_RESTORE
+			} else if (tbl[i].data == &init_ipc_ns.ids[IPC_SEM_IDS].next_id) {
+				tbl[i].data = &ns->ids[IPC_SEM_IDS].next_id;
+
+			} else if (tbl[i].data == &init_ipc_ns.ids[IPC_MSG_IDS].next_id) {
+				tbl[i].data = &ns->ids[IPC_MSG_IDS].next_id;
+
+			} else if (tbl[i].data == &init_ipc_ns.ids[IPC_SHM_IDS].next_id) {
+				tbl[i].data = &ns->ids[IPC_SHM_IDS].next_id;
+#endif
+			} else {
+				tbl[i].data = NULL;
+			}
+		}
+
+		ns->ipc_sysctls = __register_sysctl_table(&ns->ipc_set, "kernel", tbl);
+	}
+	if (!ns->ipc_sysctls) {
+		kfree(tbl);
+		retire_sysctl_set(&ns->ipc_set);
+		return false;
+	}
+
+	return true;
+}
+
+void retire_ipc_sysctls(struct ipc_namespace *ns)
+{
+	struct ctl_table *tbl;
+
+	tbl = ns->ipc_sysctls->ctl_table_arg;
+	unregister_sysctl_table(ns->ipc_sysctls);
+	retire_sysctl_set(&ns->ipc_set);
+	kfree(tbl);
+}
+
 static int __init ipc_sysctl_init(void)
 {
-	register_sysctl_table(ipc_root_table);
+	if (!setup_ipc_sysctls(&init_ipc_ns)) {
+		pr_warn("ipc sysctl registration failed\n");
+		return -ENOMEM;
+	}
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/mq_sysctl.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/mq_sysctl.c
@@ -9,39 +9,9 @@
 #include <linux/ipc_namespace.h>
 #include <linux/sysctl.h>
 
-#ifdef CONFIG_PROC_SYSCTL
-static void *get_mq(struct ctl_table *table)
-{
-	char *which = table->data;
-	struct ipc_namespace *ipc_ns = current->nsproxy->ipc_ns;
-	which = (which - (char *)&init_ipc_ns) + (char *)ipc_ns;
-	return which;
-}
-
-static int proc_mq_dointvec(struct ctl_table *table, int write,
-			    void *buffer, size_t *lenp, loff_t *ppos)
-{
-	struct ctl_table mq_table;
-	memcpy(&mq_table, table, sizeof(mq_table));
-	mq_table.data = get_mq(table);
-
-	return proc_dointvec(&mq_table, write, buffer, lenp, ppos);
-}
-
-static int proc_mq_dointvec_minmax(struct ctl_table *table, int write,
-		void *buffer, size_t *lenp, loff_t *ppos)
-{
-	struct ctl_table mq_table;
-	memcpy(&mq_table, table, sizeof(mq_table));
-	mq_table.data = get_mq(table);
-
-	return proc_dointvec_minmax(&mq_table, write, buffer,
-					lenp, ppos);
-}
-#else
-#define proc_mq_dointvec NULL
-#define proc_mq_dointvec_minmax NULL
-#endif
+#include <linux/stat.h>
+#include <linux/capability.h>
+#include <linux/slab.h>
 
 static int msg_max_limit_min = MIN_MSGMAX;
 static int msg_max_limit_max = HARD_MSGMAX;
@@ -55,14 +25,14 @@
 		.data		= &init_ipc_ns.mq_queues_max,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_mq_dointvec,
+		.proc_handler	= proc_dointvec,
 	},
 	{
 		.procname	= "msg_max",
 		.data		= &init_ipc_ns.mq_msg_max,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_mq_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= &msg_max_limit_min,
 		.extra2		= &msg_max_limit_max,
 	},
@@ -71,7 +41,7 @@
 		.data		= &init_ipc_ns.mq_msgsize_max,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_mq_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= &msg_maxsize_limit_min,
 		.extra2		= &msg_maxsize_limit_max,
 	},
@@ -80,7 +50,7 @@
 		.data		= &init_ipc_ns.mq_msg_default,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_mq_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= &msg_max_limit_min,
 		.extra2		= &msg_max_limit_max,
 	},
@@ -89,32 +59,73 @@
 		.data		= &init_ipc_ns.mq_msgsize_default,
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
-		.proc_handler	= proc_mq_dointvec_minmax,
+		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= &msg_maxsize_limit_min,
 		.extra2		= &msg_maxsize_limit_max,
 	},
 	{}
 };
 
-static struct ctl_table mq_sysctl_dir[] = {
-	{
-		.procname	= "mqueue",
-		.mode		= 0555,
-		.child		= mq_sysctls,
-	},
-	{}
-};
+static struct ctl_table_set *set_lookup(struct ctl_table_root *root)
+{
+	return &current->nsproxy->ipc_ns->mq_set;
+}
 
-static struct ctl_table mq_sysctl_root[] = {
-	{
-		.procname	= "fs",
-		.mode		= 0555,
-		.child		= mq_sysctl_dir,
-	},
-	{}
+static int set_is_seen(struct ctl_table_set *set)
+{
+	return &current->nsproxy->ipc_ns->mq_set == set;
+}
+
+static struct ctl_table_root set_root = {
+	.lookup = set_lookup,
 };
 
-struct ctl_table_header *mq_register_sysctl_table(void)
+bool setup_mq_sysctls(struct ipc_namespace *ns)
 {
-	return register_sysctl_table(mq_sysctl_root);
+	struct ctl_table *tbl;
+
+	setup_sysctl_set(&ns->mq_set, &set_root, set_is_seen);
+
+	tbl = kmemdup(mq_sysctls, sizeof(mq_sysctls), GFP_KERNEL);
+	if (tbl) {
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(mq_sysctls); i++) {
+			if (tbl[i].data == &init_ipc_ns.mq_queues_max)
+				tbl[i].data = &ns->mq_queues_max;
+
+			else if (tbl[i].data == &init_ipc_ns.mq_msg_max)
+				tbl[i].data = &ns->mq_msg_max;
+
+			else if (tbl[i].data == &init_ipc_ns.mq_msgsize_max)
+				tbl[i].data = &ns->mq_msgsize_max;
+
+			else if (tbl[i].data == &init_ipc_ns.mq_msg_default)
+				tbl[i].data = &ns->mq_msg_default;
+
+			else if (tbl[i].data == &init_ipc_ns.mq_msgsize_default)
+				tbl[i].data = &ns->mq_msgsize_default;
+			else
+				tbl[i].data = NULL;
+		}
+
+		ns->mq_sysctls = __register_sysctl_table(&ns->mq_set, "fs/mqueue", tbl);
+	}
+	if (!ns->mq_sysctls) {
+		kfree(tbl);
+		retire_sysctl_set(&ns->mq_set);
+		return false;
+	}
+
+	return true;
+}
+
+void retire_mq_sysctls(struct ipc_namespace *ns)
+{
+	struct ctl_table *tbl;
+
+	tbl = ns->mq_sysctls->ctl_table_arg;
+	unregister_sysctl_table(ns->mq_sysctls);
+	retire_sysctl_set(&ns->mq_set);
+	kfree(tbl);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/mqueue.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/mqueue.c
@@ -45,6 +45,7 @@
 
 struct mqueue_fs_context {
 	struct ipc_namespace	*ipc_ns;
+	bool			 newns;	/* Set if newly created ipc namespace */
 };
 
 #define MQUEUE_MAGIC	0x19800202
@@ -163,8 +164,6 @@
 
 static struct kmem_cache *mqueue_inode_cachep;
 
-static struct ctl_table_header *mq_sysctl_table;
-
 static inline struct mqueue_inode_info *MQUEUE_I(struct inode *inode)
 {
 	return container_of(inode, struct mqueue_inode_info, vfs_inode);
@@ -427,6 +426,14 @@
 {
 	struct mqueue_fs_context *ctx = fc->fs_private;
 
+	/*
+	 * With a newly created ipc namespace, we don't need to do a search
+	 * for an ipc namespace match, but we still need to set s_fs_info.
+	 */
+	if (ctx->newns) {
+		fc->s_fs_info = ctx->ipc_ns;
+		return get_tree_nodev(fc, mqueue_fill_super);
+	}
 	return get_tree_keyed(fc, mqueue_fill_super, ctx->ipc_ns);
 }
 
@@ -454,6 +461,10 @@
 	return 0;
 }
 
+/*
+ * mq_init_ns() is currently the only caller of mq_create_mount().
+ * So the ns parameter is always a newly created ipc namespace.
+ */
 static struct vfsmount *mq_create_mount(struct ipc_namespace *ns)
 {
 	struct mqueue_fs_context *ctx;
@@ -465,6 +476,7 @@
 		return ERR_CAST(fc);
 
 	ctx = fc->fs_private;
+	ctx->newns = true;
 	put_ipc_ns(ctx->ipc_ns);
 	ctx->ipc_ns = get_ipc_ns(ns);
 	put_user_ns(fc->user_ns);
@@ -1713,8 +1725,10 @@
 	if (mqueue_inode_cachep == NULL)
 		return -ENOMEM;
 
-	/* ignore failures - they are not fatal */
-	mq_sysctl_table = mq_register_sysctl_table();
+	if (!setup_mq_sysctls(&init_ipc_ns)) {
+		pr_warn("sysctl registration failed\n");
+		return -ENOMEM;
+	}
 
 	error = register_filesystem(&mqueue_fs_type);
 	if (error)
@@ -1731,8 +1745,6 @@
 out_filesystem:
 	unregister_filesystem(&mqueue_fs_type);
 out_sysctl:
-	if (mq_sysctl_table)
-		unregister_sysctl_table(mq_sysctl_table);
 	kmem_cache_destroy(mqueue_inode_cachep);
 	return error;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/msg.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/msg.c
@@ -39,6 +39,7 @@
 #include <linux/nsproxy.h>
 #include <linux/ipc_namespace.h>
 #include <linux/rhashtable.h>
+#include <linux/percpu_counter.h>
 
 #include <asm/current.h>
 #include <linux/uaccess.h>
@@ -285,10 +286,10 @@
 	rcu_read_unlock();
 
 	list_for_each_entry_safe(msg, t, &msq->q_messages, m_list) {
-		atomic_dec(&ns->msg_hdrs);
+		percpu_counter_sub_local(&ns->percpu_msg_hdrs, 1);
 		free_msg(msg);
 	}
-	atomic_sub(msq->q_cbytes, &ns->msg_bytes);
+	percpu_counter_sub_local(&ns->percpu_msg_bytes, msq->q_cbytes);
 	ipc_update_pid(&msq->q_lspid, NULL);
 	ipc_update_pid(&msq->q_lrpid, NULL);
 	ipc_rcu_putref(&msq->q_perm, msg_rcu_free);
@@ -495,17 +496,22 @@
 	msginfo->msgssz = MSGSSZ;
 	msginfo->msgseg = MSGSEG;
 	down_read(&msg_ids(ns).rwsem);
-	if (cmd == MSG_INFO) {
+	if (cmd == MSG_INFO)
 		msginfo->msgpool = msg_ids(ns).in_use;
-		msginfo->msgmap = atomic_read(&ns->msg_hdrs);
-		msginfo->msgtql = atomic_read(&ns->msg_bytes);
+	max_idx = ipc_get_maxidx(&msg_ids(ns));
+	up_read(&msg_ids(ns).rwsem);
+	if (cmd == MSG_INFO) {
+		msginfo->msgmap = min_t(int,
+				     percpu_counter_sum(&ns->percpu_msg_hdrs),
+				     INT_MAX);
+		msginfo->msgtql = min_t(int,
+		                     percpu_counter_sum(&ns->percpu_msg_bytes),
+				     INT_MAX);
 	} else {
 		msginfo->msgmap = MSGMAP;
 		msginfo->msgpool = MSGPOOL;
 		msginfo->msgtql = MSGTQL;
 	}
-	max_idx = ipc_get_maxidx(&msg_ids(ns));
-	up_read(&msg_ids(ns).rwsem);
 	return (max_idx < 0) ? 0 : max_idx;
 }
 
@@ -935,8 +941,8 @@
 		list_add_tail(&msg->m_list, &msq->q_messages);
 		msq->q_cbytes += msgsz;
 		msq->q_qnum++;
-		atomic_add(msgsz, &ns->msg_bytes);
-		atomic_inc(&ns->msg_hdrs);
+		percpu_counter_add_local(&ns->percpu_msg_bytes, msgsz);
+		percpu_counter_add_local(&ns->percpu_msg_hdrs, 1);
 	}
 
 	err = 0;
@@ -1159,8 +1165,8 @@
 			msq->q_rtime = ktime_get_real_seconds();
 			ipc_update_pid(&msq->q_lrpid, task_tgid(current));
 			msq->q_cbytes -= msg->m_ts;
-			atomic_sub(msg->m_ts, &ns->msg_bytes);
-			atomic_dec(&ns->msg_hdrs);
+			percpu_counter_sub_local(&ns->percpu_msg_bytes, msg->m_ts);
+			percpu_counter_sub_local(&ns->percpu_msg_hdrs, 1);
 			ss_wakeup(msq, &wake_q, false);
 
 			goto out_unlock0;
@@ -1297,20 +1303,34 @@
 }
 #endif
 
-void msg_init_ns(struct ipc_namespace *ns)
+int msg_init_ns(struct ipc_namespace *ns)
 {
+	int ret;
+
 	ns->msg_ctlmax = MSGMAX;
 	ns->msg_ctlmnb = MSGMNB;
 	ns->msg_ctlmni = MSGMNI;
 
-	atomic_set(&ns->msg_bytes, 0);
-	atomic_set(&ns->msg_hdrs, 0);
+	ret = percpu_counter_init(&ns->percpu_msg_bytes, 0, GFP_KERNEL);
+	if (ret)
+		goto fail_msg_bytes;
+	ret = percpu_counter_init(&ns->percpu_msg_hdrs, 0, GFP_KERNEL);
+	if (ret)
+		goto fail_msg_hdrs;
 	ipc_init_ids(&ns->ids[IPC_MSG_IDS]);
+	return 0;
+
+fail_msg_hdrs:
+	percpu_counter_destroy(&ns->percpu_msg_bytes);
+fail_msg_bytes:
+	return ret;
 }
 
 #ifdef CONFIG_IPC_NS
 void msg_exit_ns(struct ipc_namespace *ns)
 {
+	percpu_counter_destroy(&ns->percpu_msg_bytes);
+	percpu_counter_destroy(&ns->percpu_msg_hdrs);
 	free_ipcs(ns, &msg_ids(ns), freeque);
 	idr_destroy(&ns->ids[IPC_MSG_IDS].ipcs_idr);
 	rhashtable_destroy(&ns->ids[IPC_MSG_IDS].key_ht);
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/namespace.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/namespace.c
@@ -59,8 +59,18 @@
 	if (err)
 		goto fail_put;
 
+	err = -ENOMEM;
+	if (!setup_mq_sysctls(ns))
+		goto fail_put;
+
+	if (!setup_ipc_sysctls(ns))
+		goto fail_put;
+
+	err = msg_init_ns(ns);
+	if (err)
+		goto fail_put;
+
 	sem_init_ns(ns);
-	msg_init_ns(ns);
 	shm_init_ns(ns);
 
 	return ns;
@@ -125,6 +135,9 @@
 	msg_exit_ns(ns);
 	shm_exit_ns(ns);
 
+	retire_mq_sysctls(ns);
+	retire_ipc_sysctls(ns);
+
 	dec_ipc_namespaces(ns->ucounts);
 	put_user_ns(ns->user_ns);
 	ns_free_inum(&ns->ns);
@@ -172,6 +185,23 @@
 			schedule_work(&free_ipc_work);
 	}
 }
+EXPORT_SYMBOL(put_ipc_ns);
+
+struct ipc_namespace *get_ipc_ns_exported(struct ipc_namespace *ns)
+{
+	return get_ipc_ns(ns);
+}
+EXPORT_SYMBOL(get_ipc_ns_exported);
+
+struct ipc_namespace *show_init_ipc_ns(void)
+{
+#if defined(CONFIG_IPC_NS)
+	return &init_ipc_ns;
+#else
+	return NULL;
+#endif
+}
+EXPORT_SYMBOL(show_init_ipc_ns);
 
 static inline struct ipc_namespace *to_ipc_ns(struct ns_common *ns)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/sem.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/sem.c
@@ -1964,6 +1964,7 @@
 	 */
 	un = lookup_undo(ulp, semid);
 	if (un) {
+		spin_unlock(&ulp->lock);
 		kvfree(new);
 		goto success;
 	}
@@ -1976,9 +1977,8 @@
 	ipc_assert_locked_object(&sma->sem_perm);
 	list_add(&new->list_id, &sma->list_id);
 	un = new;
-
-success:
 	spin_unlock(&ulp->lock);
+success:
 	sem_unlock(sma, -1);
 out:
 	return un;
@@ -2182,14 +2182,15 @@
 		 * scenarios where we were awakened externally, during the
 		 * window between wake_q_add() and wake_up_q().
 		 */
+		rcu_read_lock();
 		error = READ_ONCE(queue.status);
 		if (error != -EINTR) {
 			/* see SEM_BARRIER_2 for purpose/pairing */
 			smp_acquire__after_ctrl_dep();
+			rcu_read_unlock();
 			goto out;
 		}
 
-		rcu_read_lock();
 		locknum = sem_lock(sma, sops, nsops);
 
 		if (!ipc_valid_object(&sma->sem_perm))
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/shm.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/shm.c
@@ -62,9 +62,18 @@
 	struct pid		*shm_lprid;
 	struct ucounts		*mlock_ucounts;
 
-	/* The task created the shm object.  NULL if the task is dead. */
+	/*
+	 * The task created the shm object, for
+	 * task_lock(shp->shm_creator)
+	 */
 	struct task_struct	*shm_creator;
-	struct list_head	shm_clist;	/* list by creator */
+
+	/*
+	 * List by creator. task_lock(->shm_creator) required for read/write.
+	 * If list_empty(), then the creator is dead already.
+	 */
+	struct list_head	shm_clist;
+	struct ipc_namespace	*ns;
 } __randomize_layout;
 
 /* shm_mode upper byte flags */
@@ -115,6 +124,7 @@
 	struct shmid_kernel *shp;
 
 	shp = container_of(ipcp, struct shmid_kernel, shm_perm);
+	WARN_ON(ns != shp->ns);
 
 	if (shp->shm_nattch) {
 		shp->shm_perm.mode |= SHM_DEST;
@@ -225,10 +235,43 @@
 	kfree(shp);
 }
 
-static inline void shm_rmid(struct ipc_namespace *ns, struct shmid_kernel *s)
+/*
+ * It has to be called with shp locked.
+ * It must be called before ipc_rmid()
+ */
+static inline void shm_clist_rm(struct shmid_kernel *shp)
+{
+	struct task_struct *creator;
+
+	/* ensure that shm_creator does not disappear */
+	rcu_read_lock();
+
+	/*
+	 * A concurrent exit_shm may do a list_del_init() as well.
+	 * Just do nothing if exit_shm already did the work
+	 */
+	if (!list_empty(&shp->shm_clist)) {
+		/*
+		 * shp->shm_creator is guaranteed to be valid *only*
+		 * if shp->shm_clist is not empty.
+		 */
+		creator = shp->shm_creator;
+
+		task_lock(creator);
+		/*
+		 * list_del_init() is a nop if the entry was already removed
+		 * from the list.
+		 */
+		list_del_init(&shp->shm_clist);
+		task_unlock(creator);
+	}
+	rcu_read_unlock();
+}
+
+static inline void shm_rmid(struct shmid_kernel *s)
 {
-	list_del(&s->shm_clist);
-	ipc_rmid(&shm_ids(ns), &s->shm_perm);
+	shm_clist_rm(s);
+	ipc_rmid(&shm_ids(s->ns), &s->shm_perm);
 }
 
 
@@ -283,7 +326,7 @@
 	shm_file = shp->shm_file;
 	shp->shm_file = NULL;
 	ns->shm_tot -= (shp->shm_segsz + PAGE_SIZE - 1) >> PAGE_SHIFT;
-	shm_rmid(ns, shp);
+	shm_rmid(shp);
 	shm_unlock(shp);
 	if (!is_file_hugepages(shm_file))
 		shmem_lock(shm_file, 0, shp->mlock_ucounts);
@@ -306,10 +349,10 @@
  *
  * 2) sysctl kernel.shm_rmid_forced is set to 1.
  */
-static bool shm_may_destroy(struct ipc_namespace *ns, struct shmid_kernel *shp)
+static bool shm_may_destroy(struct shmid_kernel *shp)
 {
 	return (shp->shm_nattch == 0) &&
-	       (ns->shm_rmid_forced ||
+	       (shp->ns->shm_rmid_forced ||
 		(shp->shm_perm.mode & SHM_DEST));
 }
 
@@ -340,7 +383,7 @@
 	ipc_update_pid(&shp->shm_lprid, task_tgid(current));
 	shp->shm_dtim = ktime_get_real_seconds();
 	shp->shm_nattch--;
-	if (shm_may_destroy(ns, shp))
+	if (shm_may_destroy(shp))
 		shm_destroy(ns, shp);
 	else
 		shm_unlock(shp);
@@ -361,10 +404,10 @@
 	 *
 	 * As shp->* are changed under rwsem, it's safe to skip shp locking.
 	 */
-	if (shp->shm_creator != NULL)
+	if (!list_empty(&shp->shm_clist))
 		return 0;
 
-	if (shm_may_destroy(ns, shp)) {
+	if (shm_may_destroy(shp)) {
 		shm_lock_by_ptr(shp);
 		shm_destroy(ns, shp);
 	}
@@ -382,48 +425,97 @@
 /* Locking assumes this will only be called with task == current */
 void exit_shm(struct task_struct *task)
 {
-	struct ipc_namespace *ns = task->nsproxy->ipc_ns;
-	struct shmid_kernel *shp, *n;
+	for (;;) {
+		struct shmid_kernel *shp;
+		struct ipc_namespace *ns;
 
-	if (list_empty(&task->sysvshm.shm_clist))
-		return;
+		task_lock(task);
+
+		if (list_empty(&task->sysvshm.shm_clist)) {
+			task_unlock(task);
+			break;
+		}
+
+		shp = list_first_entry(&task->sysvshm.shm_clist, struct shmid_kernel,
+				shm_clist);
 
-	/*
-	 * If kernel.shm_rmid_forced is not set then only keep track of
-	 * which shmids are orphaned, so that a later set of the sysctl
-	 * can clean them up.
-	 */
-	if (!ns->shm_rmid_forced) {
-		down_read(&shm_ids(ns).rwsem);
-		list_for_each_entry(shp, &task->sysvshm.shm_clist, shm_clist)
-			shp->shm_creator = NULL;
 		/*
-		 * Only under read lock but we are only called on current
-		 * so no entry on the list will be shared.
+		 * 1) Get pointer to the ipc namespace. It is worth to say
+		 * that this pointer is guaranteed to be valid because
+		 * shp lifetime is always shorter than namespace lifetime
+		 * in which shp lives.
+		 * We taken task_lock it means that shp won't be freed.
 		 */
-		list_del(&task->sysvshm.shm_clist);
-		up_read(&shm_ids(ns).rwsem);
-		return;
-	}
+		ns = shp->ns;
 
-	/*
-	 * Destroy all already created segments, that were not yet mapped,
-	 * and mark any mapped as orphan to cover the sysctl toggling.
-	 * Destroy is skipped if shm_may_destroy() returns false.
-	 */
-	down_write(&shm_ids(ns).rwsem);
-	list_for_each_entry_safe(shp, n, &task->sysvshm.shm_clist, shm_clist) {
-		shp->shm_creator = NULL;
+		/*
+		 * 2) If kernel.shm_rmid_forced is not set then only keep track of
+		 * which shmids are orphaned, so that a later set of the sysctl
+		 * can clean them up.
+		 */
+		if (!ns->shm_rmid_forced)
+			goto unlink_continue;
 
-		if (shm_may_destroy(ns, shp)) {
-			shm_lock_by_ptr(shp);
-			shm_destroy(ns, shp);
+		/*
+		 * 3) get a reference to the namespace.
+		 *    The refcount could be already 0. If it is 0, then
+		 *    the shm objects will be free by free_ipc_work().
+		 */
+		ns = get_ipc_ns_not_zero(ns);
+		if (!ns) {
+unlink_continue:
+			list_del_init(&shp->shm_clist);
+			task_unlock(task);
+			continue;
 		}
-	}
 
-	/* Remove the list head from any segments still attached. */
-	list_del(&task->sysvshm.shm_clist);
-	up_write(&shm_ids(ns).rwsem);
+		/*
+		 * 4) get a reference to shp.
+		 *   This cannot fail: shm_clist_rm() is called before
+		 *   ipc_rmid(), thus the refcount cannot be 0.
+		 */
+		WARN_ON(!ipc_rcu_getref(&shp->shm_perm));
+
+		/*
+		 * 5) unlink the shm segment from the list of segments
+		 *    created by current.
+		 *    This must be done last. After unlinking,
+		 *    only the refcounts obtained above prevent IPC_RMID
+		 *    from destroying the segment or the namespace.
+		 */
+		list_del_init(&shp->shm_clist);
+
+		task_unlock(task);
+
+		/*
+		 * 6) we have all references
+		 *    Thus lock & if needed destroy shp.
+		 */
+		down_write(&shm_ids(ns).rwsem);
+		shm_lock_by_ptr(shp);
+		/*
+		 * rcu_read_lock was implicitly taken in shm_lock_by_ptr, it's
+		 * safe to call ipc_rcu_putref here
+		 */
+		ipc_rcu_putref(&shp->shm_perm, shm_rcu_free);
+
+		if (ipc_valid_object(&shp->shm_perm)) {
+			if (shm_may_destroy(shp))
+				shm_destroy(ns, shp);
+			else
+				shm_unlock(shp);
+		} else {
+			/*
+			 * Someone else deleted the shp from namespace
+			 * idr/kht while we have waited.
+			 * Just unlock and continue.
+			 */
+			shm_unlock(shp);
+		}
+
+		up_write(&shm_ids(ns).rwsem);
+		put_ipc_ns(ns); /* paired with get_ipc_ns_not_zero */
+	}
 }
 
 static vm_fault_t shm_fault(struct vm_fault *vmf)
@@ -680,7 +772,11 @@
 	if (error < 0)
 		goto no_id;
 
+	shp->ns = ns;
+
+	task_lock(current);
 	list_add(&shp->shm_clist, &current->sysvshm.shm_clist);
+	task_unlock(current);
 
 	/*
 	 * shmid gets reported as "inode#" in /proc/pid/maps.
@@ -1573,7 +1669,8 @@
 	down_write(&shm_ids(ns).rwsem);
 	shp = shm_lock(ns, shmid);
 	shp->shm_nattch--;
-	if (shm_may_destroy(ns, shp))
+
+	if (shm_may_destroy(shp))
 		shm_destroy(ns, shp);
 	else
 		shm_unlock(shp);
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/util.c
+++ linux-xilinx-zynqmp-5.15.0/ipc/util.c
@@ -447,8 +447,8 @@
 static void ipc_kht_remove(struct ipc_ids *ids, struct kern_ipc_perm *ipcp)
 {
 	if (ipcp->key != IPC_PRIVATE)
-		rhashtable_remove_fast(&ids->key_ht, &ipcp->khtnode,
-				       ipc_kht_params);
+		WARN_ON_ONCE(rhashtable_remove_fast(&ids->key_ht, &ipcp->khtnode,
+				       ipc_kht_params));
 }
 
 /**
@@ -498,7 +498,7 @@
 {
 	int idx = ipcid_to_idx(ipcp->id);
 
-	idr_remove(&ids->ipcs_idr, idx);
+	WARN_ON_ONCE(idr_remove(&ids->ipcs_idr, idx) != ipcp);
 	ipc_kht_remove(ids, ipcp);
 	ids->in_use--;
 	ipcp->deleted = true;
--- linux-xilinx-zynqmp-5.15.0.orig/ipc/util.h
+++ linux-xilinx-zynqmp-5.15.0/ipc/util.h
@@ -64,7 +64,7 @@
 
 #ifdef CONFIG_SYSVIPC
 void sem_init_ns(struct ipc_namespace *ns);
-void msg_init_ns(struct ipc_namespace *ns);
+int msg_init_ns(struct ipc_namespace *ns);
 void shm_init_ns(struct ipc_namespace *ns);
 
 void sem_exit_ns(struct ipc_namespace *ns);
@@ -72,7 +72,7 @@
 void shm_exit_ns(struct ipc_namespace *ns);
 #else
 static inline void sem_init_ns(struct ipc_namespace *ns) { }
-static inline void msg_init_ns(struct ipc_namespace *ns) { }
+static inline int msg_init_ns(struct ipc_namespace *ns) { return 0; }
 static inline void shm_init_ns(struct ipc_namespace *ns) { }
 
 static inline void sem_exit_ns(struct ipc_namespace *ns) { }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/Makefile
+++ linux-xilinx-zynqmp-5.15.0/kernel/Makefile
@@ -59,7 +59,7 @@
 obj-$(CONFIG_PROFILING) += profile.o
 obj-$(CONFIG_STACKTRACE) += stacktrace.o
 obj-y += time/
-obj-$(CONFIG_FUTEX) += futex.o
+obj-$(CONFIG_FUTEX) += futex/
 obj-$(CONFIG_GENERIC_ISA_DMA) += dma.o
 obj-$(CONFIG_SMP) += smp.o
 ifneq ($(CONFIG_SMP),y)
@@ -113,7 +113,8 @@
 obj-$(CONFIG_BPF) += bpf/
 obj-$(CONFIG_KCSAN) += kcsan/
 obj-$(CONFIG_SHADOW_CALL_STACK) += scs.o
-obj-$(CONFIG_HAVE_STATIC_CALL_INLINE) += static_call.o
+obj-$(CONFIG_HAVE_STATIC_CALL) += static_call.o
+obj-$(CONFIG_HAVE_STATIC_CALL_INLINE) += static_call_inline.o
 obj-$(CONFIG_CFI_CLANG) += cfi.o
 
 obj-$(CONFIG_PERF_EVENTS) += events/
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/acct.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/acct.c
@@ -85,48 +85,50 @@
 	atomic_long_t		count;
 	struct rcu_head		rcu;
 	struct mutex		lock;
-	int			active;
+	bool			active;
+	bool			check_space;
 	unsigned long		needcheck;
 	struct file		*file;
 	struct pid_namespace	*ns;
 	struct work_struct	work;
 	struct completion	done;
+	acct_t			ac;
 };
 
-static void do_acct_process(struct bsd_acct_struct *acct);
+static void fill_ac(struct bsd_acct_struct *acct);
+static void acct_write_process(struct bsd_acct_struct *acct);
 
 /*
  * Check the amount of free space and suspend/resume accordingly.
  */
-static int check_free_space(struct bsd_acct_struct *acct)
+static bool check_free_space(struct bsd_acct_struct *acct)
 {
 	struct kstatfs sbuf;
 
-	if (time_is_after_jiffies(acct->needcheck))
-		goto out;
+	if (!acct->check_space)
+		return acct->active;
 
 	/* May block */
 	if (vfs_statfs(&acct->file->f_path, &sbuf))
-		goto out;
+		return acct->active;
 
 	if (acct->active) {
 		u64 suspend = sbuf.f_blocks * SUSPEND;
 		do_div(suspend, 100);
 		if (sbuf.f_bavail <= suspend) {
-			acct->active = 0;
+			acct->active = false;
 			pr_info("Process accounting paused\n");
 		}
 	} else {
 		u64 resume = sbuf.f_blocks * RESUME;
 		do_div(resume, 100);
 		if (sbuf.f_bavail >= resume) {
-			acct->active = 1;
+			acct->active = true;
 			pr_info("Process accounting resumed\n");
 		}
 	}
 
 	acct->needcheck = jiffies + ACCT_TIMEOUT*HZ;
-out:
 	return acct->active;
 }
 
@@ -171,7 +173,11 @@
 {
 	struct bsd_acct_struct *acct = to_acct(pin);
 	mutex_lock(&acct->lock);
-	do_acct_process(acct);
+	/*
+	 * Fill the accounting struct with the exiting task's info
+	 * before punting to the workqueue.
+	 */
+	fill_ac(acct);
 	schedule_work(&acct->work);
 	wait_for_completion(&acct->done);
 	cmpxchg(&acct->ns->bacct, pin, NULL);
@@ -184,6 +190,9 @@
 {
 	struct bsd_acct_struct *acct = container_of(work, struct bsd_acct_struct, work);
 	struct file *file = acct->file;
+
+	/* We were fired by acct_pin_kill() which holds acct->lock. */
+	acct_write_process(acct);
 	if (file->f_op->flush)
 		file->f_op->flush(file, NULL);
 	__fput_sync(file);
@@ -216,6 +225,20 @@
 		return -EACCES;
 	}
 
+	/* Exclude kernel kernel internal filesystems. */
+	if (file_inode(file)->i_sb->s_flags & (SB_NOUSER | SB_KERNMOUNT)) {
+		kfree(acct);
+		filp_close(file, NULL);
+		return -EINVAL;
+	}
+
+	/* Exclude procfs and sysfs. */
+	if (file_inode(file)->i_sb->s_iflags & SB_I_USERNS_VISIBLE) {
+		kfree(acct);
+		filp_close(file, NULL);
+		return -EINVAL;
+	}
+
 	if (!(file->f_mode & FMODE_CAN_WRITE)) {
 		kfree(acct);
 		filp_close(file, NULL);
@@ -331,6 +354,8 @@
 		exp++;
 	}
 
+	if (exp > (((comp_t) ~0U) >> MANTSIZE))
+		return (comp_t) ~0U;
 	/*
 	 * Clean it up and polish it off.
 	 */
@@ -410,13 +435,27 @@
  *  do_exit() or when switching to a different output file.
  */
 
-static void fill_ac(acct_t *ac)
+static void fill_ac(struct bsd_acct_struct *acct)
 {
 	struct pacct_struct *pacct = &current->signal->pacct;
+	struct file *file = acct->file;
+	acct_t *ac = &acct->ac;
 	u64 elapsed, run_time;
 	time64_t btime;
 	struct tty_struct *tty;
 
+	lockdep_assert_held(&acct->lock);
+
+	if (time_is_after_jiffies(acct->needcheck)) {
+		acct->check_space = false;
+
+		/* Don't fill in @ac if nothing will be written. */
+		if (!acct->active)
+			return;
+	} else {
+		acct->check_space = true;
+	}
+
 	/*
 	 * Fill the accounting struct with the needed info as recorded
 	 * by the different kernel functions.
@@ -464,64 +503,61 @@
 	ac->ac_majflt = encode_comp_t(pacct->ac_majflt);
 	ac->ac_exitcode = pacct->ac_exitcode;
 	spin_unlock_irq(&current->sighand->siglock);
-}
-/*
- *  do_acct_process does all actual work. Caller holds the reference to file.
- */
-static void do_acct_process(struct bsd_acct_struct *acct)
-{
-	acct_t ac;
-	unsigned long flim;
-	const struct cred *orig_cred;
-	struct file *file = acct->file;
 
-	/*
-	 * Accounting records are not subject to resource limits.
-	 */
-	flim = rlimit(RLIMIT_FSIZE);
-	current->signal->rlim[RLIMIT_FSIZE].rlim_cur = RLIM_INFINITY;
-	/* Perform file operations on behalf of whoever enabled accounting */
-	orig_cred = override_creds(file->f_cred);
-
-	/*
-	 * First check to see if there is enough free_space to continue
-	 * the process accounting system.
-	 */
-	if (!check_free_space(acct))
-		goto out;
-
-	fill_ac(&ac);
 	/* we really need to bite the bullet and change layout */
-	ac.ac_uid = from_kuid_munged(file->f_cred->user_ns, orig_cred->uid);
-	ac.ac_gid = from_kgid_munged(file->f_cred->user_ns, orig_cred->gid);
+	ac->ac_uid = from_kuid_munged(file->f_cred->user_ns, current_uid());
+	ac->ac_gid = from_kgid_munged(file->f_cred->user_ns, current_gid());
 #if ACCT_VERSION == 1 || ACCT_VERSION == 2
 	/* backward-compatible 16 bit fields */
-	ac.ac_uid16 = ac.ac_uid;
-	ac.ac_gid16 = ac.ac_gid;
+	ac->ac_uid16 = ac->ac_uid;
+	ac->ac_gid16 = ac->ac_gid;
 #elif ACCT_VERSION == 3
 	{
 		struct pid_namespace *ns = acct->ns;
 
-		ac.ac_pid = task_tgid_nr_ns(current, ns);
+		ac->ac_pid = task_tgid_nr_ns(current, ns);
 		rcu_read_lock();
-		ac.ac_ppid = task_tgid_nr_ns(rcu_dereference(current->real_parent),
-					     ns);
+		ac->ac_ppid = task_tgid_nr_ns(rcu_dereference(current->real_parent), ns);
 		rcu_read_unlock();
 	}
 #endif
+}
+
+static void acct_write_process(struct bsd_acct_struct *acct)
+{
+	struct file *file = acct->file;
+	const struct cred *cred;
+	acct_t *ac = &acct->ac;
+
+	/* Perform file operations on behalf of whoever enabled accounting */
+	cred = override_creds(file->f_cred);
+
 	/*
-	 * Get freeze protection. If the fs is frozen, just skip the write
-	 * as we could deadlock the system otherwise.
+	 * First check to see if there is enough free_space to continue
+	 * the process accounting system. Then get freeze protection. If
+	 * the fs is frozen, just skip the write as we could deadlock
+	 * the system otherwise.
 	 */
-	if (file_start_write_trylock(file)) {
+	if (check_free_space(acct) && file_start_write_trylock(file)) {
 		/* it's been opened O_APPEND, so position is irrelevant */
 		loff_t pos = 0;
-		__kernel_write(file, &ac, sizeof(acct_t), &pos);
+		__kernel_write(file, ac, sizeof(acct_t), &pos);
 		file_end_write(file);
 	}
-out:
+
+	revert_creds(cred);
+}
+
+static void do_acct_process(struct bsd_acct_struct *acct)
+{
+	unsigned long flim;
+
+	/* Accounting records are not subject to resource limits. */
+	flim = rlimit(RLIMIT_FSIZE);
+	current->signal->rlim[RLIMIT_FSIZE].rlim_cur = RLIM_INFINITY;
+	fill_ac(acct);
+	acct_write_process(acct);
 	current->signal->rlim[RLIMIT_FSIZE].rlim_cur = flim;
-	revert_creds(orig_cred);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/async.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/async.c
@@ -145,6 +145,39 @@
 	wake_up(&async_done);
 }
 
+static async_cookie_t __async_schedule_node_domain(async_func_t func,
+						   void *data, int node,
+						   struct async_domain *domain,
+						   struct async_entry *entry)
+{
+	async_cookie_t newcookie;
+	unsigned long flags;
+
+	INIT_LIST_HEAD(&entry->domain_list);
+	INIT_LIST_HEAD(&entry->global_list);
+	INIT_WORK(&entry->work, async_run_entry_fn);
+	entry->func = func;
+	entry->data = data;
+	entry->domain = domain;
+
+	spin_lock_irqsave(&async_lock, flags);
+
+	/* allocate cookie and queue */
+	newcookie = entry->cookie = next_cookie++;
+
+	list_add_tail(&entry->domain_list, &domain->pending);
+	if (domain->registered)
+		list_add_tail(&entry->global_list, &async_global_pending);
+
+	atomic_inc(&entry_count);
+	spin_unlock_irqrestore(&async_lock, flags);
+
+	/* schedule for execution */
+	queue_work_node(node, system_unbound_wq, &entry->work);
+
+	return newcookie;
+}
+
 /**
  * async_schedule_node_domain - NUMA specific version of async_schedule_domain
  * @func: function to execute asynchronously
@@ -186,32 +219,8 @@
 		func(data, newcookie);
 		return newcookie;
 	}
-	INIT_LIST_HEAD(&entry->domain_list);
-	INIT_LIST_HEAD(&entry->global_list);
-	INIT_WORK(&entry->work, async_run_entry_fn);
-	entry->func = func;
-	entry->data = data;
-	entry->domain = domain;
-
-	spin_lock_irqsave(&async_lock, flags);
-
-	/* allocate cookie and queue */
-	newcookie = entry->cookie = next_cookie++;
-
-	list_add_tail(&entry->domain_list, &domain->pending);
-	if (domain->registered)
-		list_add_tail(&entry->global_list, &async_global_pending);
-
-	atomic_inc(&entry_count);
-	spin_unlock_irqrestore(&async_lock, flags);
-
-	/* mark that this task has queued an async job, used by module init */
-	current->flags |= PF_USED_ASYNC;
-
-	/* schedule for execution */
-	queue_work_node(node, system_unbound_wq, &entry->work);
 
-	return newcookie;
+	return __async_schedule_node_domain(func, data, node, domain, entry);
 }
 EXPORT_SYMBOL_GPL(async_schedule_node_domain);
 
@@ -235,6 +244,35 @@
 EXPORT_SYMBOL_GPL(async_schedule_node);
 
 /**
+ * async_schedule_dev_nocall - A simplified variant of async_schedule_dev()
+ * @func: function to execute asynchronously
+ * @dev: device argument to be passed to function
+ *
+ * @dev is used as both the argument for the function and to provide NUMA
+ * context for where to run the function.
+ *
+ * If the asynchronous execution of @func is scheduled successfully, return
+ * true. Otherwise, do nothing and return false, unlike async_schedule_dev()
+ * that will run the function synchronously then.
+ */
+bool async_schedule_dev_nocall(async_func_t func, struct device *dev)
+{
+	struct async_entry *entry;
+
+	entry = kzalloc(sizeof(struct async_entry), GFP_KERNEL);
+
+	/* Give up if there is no memory or too much work. */
+	if (!entry || atomic_read(&entry_count) > MAX_WORK) {
+		kfree(entry);
+		return false;
+	}
+
+	__async_schedule_node_domain(func, dev, dev_to_node(dev),
+				     &async_dfl_domain, entry);
+	return true;
+}
+
+/**
  * async_synchronize_full - synchronize all asynchronous function calls
  *
  * This function waits until all asynchronous function calls have been done.
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/audit.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/audit.c
@@ -125,7 +125,7 @@
 /* The identity of the user shutting down the audit system. */
 static kuid_t		audit_sig_uid = INVALID_UID;
 static pid_t		audit_sig_pid = -1;
-static u32		audit_sig_sid;
+struct lsmblob	audit_sig_lsm;
 
 /* Records can be lost in several ways:
    0) [suppressed in audit_alloc]
@@ -394,10 +394,11 @@
 		return rc;
 	audit_log_format(ab, "op=set %s=%u old=%u ", function_name, new, old);
 	audit_log_session_info(ab);
-	rc = audit_log_task_context(ab);
+	rc = audit_log_task_context(ab, NULL);
 	if (rc)
 		allow_changes = 0; /* Something weird, deny request */
 	audit_log_format(ab, " res=%d", allow_changes);
+	audit_log_lsm(NULL, false);
 	audit_log_end(ab);
 	return rc;
 }
@@ -490,15 +491,19 @@
  * @pid: auditd PID
  * @portid: auditd netlink portid
  * @net: auditd network namespace pointer
+ * @skb: the netlink command from the audit daemon
+ * @ack: netlink ack flag, cleared if ack'd here
  *
  * Description:
  * This function will obtain and drop network namespace references as
  * necessary.  Returns zero on success, negative values on failure.
  */
-static int auditd_set(struct pid *pid, u32 portid, struct net *net)
+static int auditd_set(struct pid *pid, u32 portid, struct net *net,
+		      struct sk_buff *skb, bool *ack)
 {
 	unsigned long flags;
 	struct auditd_connection *ac_old, *ac_new;
+	struct nlmsghdr *nlh;
 
 	if (!pid || !net)
 		return -EINVAL;
@@ -510,6 +515,13 @@
 	ac_new->portid = portid;
 	ac_new->net = get_net(net);
 
+	/* send the ack now to avoid a race with the queue backlog */
+	if (*ack) {
+		nlh = nlmsg_hdr(skb);
+		netlink_ack(skb, nlh, 0, NULL);
+		*ack = false;
+	}
+
 	spin_lock_irqsave(&auditd_conn_lock, flags);
 	ac_old = rcu_dereference_protected(auditd_conn,
 					   lockdep_is_held(&auditd_conn_lock));
@@ -541,20 +553,22 @@
 /**
  * kauditd_rehold_skb - Handle a audit record send failure in the hold queue
  * @skb: audit record
+ * @error: error code (unused)
  *
  * Description:
  * This should only be used by the kauditd_thread when it fails to flush the
  * hold queue.
  */
-static void kauditd_rehold_skb(struct sk_buff *skb)
+static void kauditd_rehold_skb(struct sk_buff *skb, __always_unused int error)
 {
-	/* put the record back in the queue at the same place */
-	skb_queue_head(&audit_hold_queue, skb);
+	/* put the record back in the queue */
+	skb_queue_tail(&audit_hold_queue, skb);
 }
 
 /**
  * kauditd_hold_skb - Queue an audit record, waiting for auditd
  * @skb: audit record
+ * @error: error code
  *
  * Description:
  * Queue the audit record, waiting for an instance of auditd.  When this
@@ -564,19 +578,31 @@
  * and queue it, if we have room.  If we want to hold on to the record, but we
  * don't have room, record a record lost message.
  */
-static void kauditd_hold_skb(struct sk_buff *skb)
+static void kauditd_hold_skb(struct sk_buff *skb, int error)
 {
 	/* at this point it is uncertain if we will ever send this to auditd so
 	 * try to send the message via printk before we go any further */
 	kauditd_printk_skb(skb);
 
 	/* can we just silently drop the message? */
-	if (!audit_default) {
-		kfree_skb(skb);
-		return;
+	if (!audit_default)
+		goto drop;
+
+	/* the hold queue is only for when the daemon goes away completely,
+	 * not -EAGAIN failures; if we are in a -EAGAIN state requeue the
+	 * record on the retry queue unless it's full, in which case drop it
+	 */
+	if (error == -EAGAIN) {
+		if (!audit_backlog_limit ||
+		    skb_queue_len(&audit_retry_queue) < audit_backlog_limit) {
+			skb_queue_tail(&audit_retry_queue, skb);
+			return;
+		}
+		audit_log_lost("kauditd retry queue overflow");
+		goto drop;
 	}
 
-	/* if we have room, queue the message */
+	/* if we have room in the hold queue, queue the message */
 	if (!audit_backlog_limit ||
 	    skb_queue_len(&audit_hold_queue) < audit_backlog_limit) {
 		skb_queue_tail(&audit_hold_queue, skb);
@@ -585,24 +611,32 @@
 
 	/* we have no other options - drop the message */
 	audit_log_lost("kauditd hold queue overflow");
+drop:
 	kfree_skb(skb);
 }
 
 /**
  * kauditd_retry_skb - Queue an audit record, attempt to send again to auditd
  * @skb: audit record
+ * @error: error code (unused)
  *
  * Description:
  * Not as serious as kauditd_hold_skb() as we still have a connected auditd,
  * but for some reason we are having problems sending it audit records so
  * queue the given record and attempt to resend.
  */
-static void kauditd_retry_skb(struct sk_buff *skb)
+static void kauditd_retry_skb(struct sk_buff *skb, __always_unused int error)
 {
-	/* NOTE: because records should only live in the retry queue for a
-	 * short period of time, before either being sent or moved to the hold
-	 * queue, we don't currently enforce a limit on this queue */
-	skb_queue_tail(&audit_retry_queue, skb);
+	if (!audit_backlog_limit ||
+	    skb_queue_len(&audit_retry_queue) < audit_backlog_limit) {
+		skb_queue_tail(&audit_retry_queue, skb);
+		return;
+	}
+
+	/* we have to drop the record, send it via printk as a last effort */
+	kauditd_printk_skb(skb);
+	audit_log_lost("kauditd retry queue overflow");
+	kfree_skb(skb);
 }
 
 /**
@@ -640,7 +674,7 @@
 	/* flush the retry queue to the hold queue, but don't touch the main
 	 * queue since we need to process that normally for multicast */
 	while ((skb = skb_dequeue(&audit_retry_queue)))
-		kauditd_hold_skb(skb);
+		kauditd_hold_skb(skb, -ECONNREFUSED);
 }
 
 /**
@@ -714,16 +748,18 @@
 			      struct sk_buff_head *queue,
 			      unsigned int retry_limit,
 			      void (*skb_hook)(struct sk_buff *skb),
-			      void (*err_hook)(struct sk_buff *skb))
+			      void (*err_hook)(struct sk_buff *skb, int error))
 {
 	int rc = 0;
-	struct sk_buff *skb;
-	static unsigned int failed = 0;
+	struct sk_buff *skb = NULL;
+	struct sk_buff *skb_tail;
+	unsigned int failed = 0;
 
 	/* NOTE: kauditd_thread takes care of all our locking, we just use
 	 *       the netlink info passed to us (e.g. sk and portid) */
 
-	while ((skb = skb_dequeue(queue))) {
+	skb_tail = skb_peek_tail(queue);
+	while ((skb != skb_tail) && (skb = skb_dequeue(queue))) {
 		/* call the skb_hook for each skb we touch */
 		if (skb_hook)
 			(*skb_hook)(skb);
@@ -731,36 +767,34 @@
 		/* can we send to anyone via unicast? */
 		if (!sk) {
 			if (err_hook)
-				(*err_hook)(skb);
+				(*err_hook)(skb, -ECONNREFUSED);
 			continue;
 		}
 
+retry:
 		/* grab an extra skb reference in case of error */
 		skb_get(skb);
 		rc = netlink_unicast(sk, skb, portid, 0);
 		if (rc < 0) {
-			/* fatal failure for our queue flush attempt? */
+			/* send failed - try a few times unless fatal error */
 			if (++failed >= retry_limit ||
 			    rc == -ECONNREFUSED || rc == -EPERM) {
-				/* yes - error processing for the queue */
 				sk = NULL;
 				if (err_hook)
-					(*err_hook)(skb);
-				if (!skb_hook)
-					goto out;
-				/* keep processing with the skb_hook */
+					(*err_hook)(skb, rc);
+				if (rc == -EAGAIN)
+					rc = 0;
+				/* continue to drain the queue */
 				continue;
 			} else
-				/* no - requeue to preserve ordering */
-				skb_queue_head(queue, skb);
+				goto retry;
 		} else {
-			/* it worked - drop the extra reference and continue */
+			/* skb sent - drop the extra reference and continue */
 			consume_skb(skb);
 			failed = 0;
 		}
 	}
 
-out:
 	return (rc >= 0 ? 0 : rc);
 }
 
@@ -1069,13 +1103,31 @@
 		return;
 	audit_log_format(*ab, "pid=%d uid=%u ", pid, uid);
 	audit_log_session_info(*ab);
-	audit_log_task_context(*ab);
+	audit_log_task_context(*ab, NULL);
 }
 
 static inline void audit_log_user_recv_msg(struct audit_buffer **ab,
 					   u16 msg_type)
 {
-	audit_log_common_recv_msg(NULL, ab, msg_type);
+	struct audit_context *context;
+
+	if (!lsm_multiple_contexts()) {
+		audit_log_common_recv_msg(NULL, ab, msg_type);
+		return;
+	}
+
+	context = audit_context();
+	if (context) {
+		if (!context->in_syscall)
+			audit_stamp_context(context);
+		audit_log_common_recv_msg(context, ab, msg_type);
+		return;
+	}
+
+	audit_alloc(current);
+	context = audit_context();
+
+	audit_log_common_recv_msg(context, ab, msg_type);
 }
 
 int is_audit_feature_set(int i)
@@ -1181,7 +1233,8 @@
 	return auditd_send_unicast_skb(skb);
 }
 
-static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh)
+static int audit_receive_msg(struct sk_buff *skb, struct nlmsghdr *nlh,
+			     bool *ack)
 {
 	u32			seq;
 	void			*data;
@@ -1190,8 +1243,6 @@
 	struct audit_buffer	*ab;
 	u16			msg_type = nlh->nlmsg_type;
 	struct audit_sig_info   *sig_data;
-	char			*ctx = NULL;
-	u32			len;
 
 	err = audit_netlink_ok(skb, msg_type);
 	if (err)
@@ -1274,7 +1325,8 @@
 				/* register a new auditd connection */
 				err = auditd_set(req_pid,
 						 NETLINK_CB(skb).portid,
-						 sock_net(NETLINK_CB(skb).sk));
+						 sock_net(NETLINK_CB(skb).sk),
+						 skb, ack);
 				if (audit_enabled != AUDIT_OFF)
 					audit_log_config_change("audit_pid",
 								new_pid,
@@ -1373,6 +1425,7 @@
 				audit_log_n_untrustedstring(ab, str, data_len);
 			}
 			audit_log_end(ab);
+			audit_log_lsm(NULL, false);
 		}
 		break;
 	case AUDIT_ADD_RULE:
@@ -1439,29 +1492,34 @@
 		kfree(new);
 		break;
 	}
-	case AUDIT_SIGNAL_INFO:
-		len = 0;
-		if (audit_sig_sid) {
-			err = security_secid_to_secctx(audit_sig_sid, &ctx, &len);
+	case AUDIT_SIGNAL_INFO: {
+		struct lsmcontext context = { };
+		int len = 0;
+
+		if (lsmblob_is_set(&audit_sig_lsm)) {
+			err = security_secid_to_secctx(&audit_sig_lsm,
+						       &context, LSMBLOB_FIRST);
 			if (err)
 				return err;
 		}
-		sig_data = kmalloc(sizeof(*sig_data) + len, GFP_KERNEL);
+		sig_data = kmalloc(sizeof(*sig_data) + context.len, GFP_KERNEL);
 		if (!sig_data) {
-			if (audit_sig_sid)
-				security_release_secctx(ctx, len);
+			if (lsmblob_is_set(&audit_sig_lsm))
+				security_release_secctx(&context);
 			return -ENOMEM;
 		}
 		sig_data->uid = from_kuid(&init_user_ns, audit_sig_uid);
 		sig_data->pid = audit_sig_pid;
-		if (audit_sig_sid) {
-			memcpy(sig_data->ctx, ctx, len);
-			security_release_secctx(ctx, len);
+		if (lsmblob_is_set(&audit_sig_lsm)) {
+			len = context.len;
+			memcpy(sig_data->ctx, context.context, len);
+			security_release_secctx(&context);
 		}
 		audit_send_reply(skb, seq, AUDIT_SIGNAL_INFO, 0, 0,
 				 sig_data, sizeof(*sig_data) + len);
 		kfree(sig_data);
 		break;
+	}
 	case AUDIT_TTY_GET: {
 		struct audit_tty_status s;
 		unsigned int t;
@@ -1519,9 +1577,10 @@
  * Parse the provided skb and deal with any messages that may be present,
  * malformed skbs are discarded.
  */
-static void audit_receive(struct sk_buff  *skb)
+static void audit_receive(struct sk_buff *skb)
 {
 	struct nlmsghdr *nlh;
+	bool ack;
 	/*
 	 * len MUST be signed for nlmsg_next to be able to dec it below 0
 	 * if the nlmsg_len was not aligned
@@ -1534,14 +1593,31 @@
 
 	audit_ctl_lock();
 	while (nlmsg_ok(nlh, len)) {
-		err = audit_receive_msg(skb, nlh);
-		/* if err or if this message says it wants a response */
-		if (err || (nlh->nlmsg_flags & NLM_F_ACK))
+		ack = nlh->nlmsg_flags & NLM_F_ACK;
+		err = audit_receive_msg(skb, nlh, &ack);
+
+		/* send an ack if the user asked for one and audit_receive_msg
+		 * didn't already do it, or if there was an error. */
+		if (ack || err)
 			netlink_ack(skb, nlh, err, NULL);
 
 		nlh = nlmsg_next(nlh, &len);
 	}
 	audit_ctl_unlock();
+
+	/* can't block with the ctrl lock, so penalize the sender now */
+	if (audit_backlog_limit &&
+	    (skb_queue_len(&audit_queue) > audit_backlog_limit)) {
+		DECLARE_WAITQUEUE(wait, current);
+
+		/* wake kauditd to try and flush the queue */
+		wake_up_interruptible(&kauditd_wait);
+
+		add_wait_queue_exclusive(&audit_backlog_wait, &wait);
+		set_current_state(TASK_UNINTERRUPTIBLE);
+		schedule_timeout(audit_backlog_wait_time);
+		remove_wait_queue(&audit_backlog_wait, &wait);
+	}
 }
 
 /* Log information about who is connecting to the audit multicast socket */
@@ -1568,7 +1644,7 @@
 			 tty ? tty_name(tty) : "(none)",
 			 audit_get_sessionid(current));
 	audit_put_tty(tty);
-	audit_log_task_context(ab); /* subj= */
+	audit_log_task_context(ab, NULL); /* subj= */
 	audit_log_format(ab, " comm=");
 	audit_log_untrustedstring(ab, get_task_comm(comm, current));
 	audit_log_d_path_exe(ab, current->mm); /* exe= */
@@ -1609,7 +1685,8 @@
 		audit_panic("cannot initialize netlink socket in namespace");
 		return -ENOMEM;
 	}
-	aunet->sk->sk_sndtimeo = MAX_SCHEDULE_TIMEOUT;
+	/* limit the timeout in case auditd is blocked/stopped */
+	aunet->sk->sk_sndtimeo = HZ / 10;
 
 	return 0;
 }
@@ -1825,7 +1902,9 @@
 	 *    task_tgid_vnr() since auditd_pid is set in audit_receive_msg()
 	 *    using a PID anchored in the caller's namespace
 	 * 2. generator holding the audit_cmd_mutex - we don't want to block
-	 *    while holding the mutex */
+	 *    while holding the mutex, although we do penalize the sender
+	 *    later in audit_receive() when it is safe to block
+	 */
 	if (!(auditd_test_task(current) || audit_ctl_owner_current())) {
 		long stime = audit_backlog_wait_time;
 
@@ -1868,6 +1947,11 @@
 	/* cancel dummy context to enable supporting records */
 	if (ctx)
 		ctx->dummy = 0;
+	if (type == AUDIT_MAC_TASK_CONTEXTS && ab->ctx &&
+	    ab->ctx->serial == 0) {
+		audit_stamp_context(ab->ctx);
+		audit_get_stamp(ab->ctx, &t, &serial);
+	}
 	audit_log_format(ab, "audit(%llu.%03lu:%u): ",
 			 (unsigned long long)t.tv_sec, t.tv_nsec/1000000, serial);
 
@@ -2125,34 +2209,103 @@
 		audit_log_format(ab, "(null)");
 }
 
-int audit_log_task_context(struct audit_buffer *ab)
+int audit_log_task_context(struct audit_buffer *ab, struct lsmblob *blob)
 {
-	char *ctx = NULL;
-	unsigned len;
+	int i;
 	int error;
-	u32 sid;
+	struct lsmblob localblob;
+	struct lsmcontext lsmdata;
 
-	security_task_getsecid_subj(current, &sid);
-	if (!sid)
+	/*
+	 * If there is more than one security module that has a
+	 * subject "context" it's necessary to put the subject data
+	 * into a separate record to maintain compatibility.
+	 */
+	if (lsm_multiple_contexts()) {
+		audit_log_format(ab, " subj=?");
 		return 0;
+	}
 
-	error = security_secid_to_secctx(sid, &ctx, &len);
-	if (error) {
-		if (error != -EINVAL)
-			goto error_path;
-		return 0;
+	if (blob == NULL) {
+		security_task_getsecid_subj(current, &localblob);
+		if (!lsmblob_is_set(&localblob)) {
+			audit_log_format(ab, " subj=?");
+			return 0;
+		}
+		blob = &localblob;
 	}
 
-	audit_log_format(ab, " subj=%s", ctx);
-	security_release_secctx(ctx, len);
-	return 0;
+	for (i = 0; i < LSMBLOB_ENTRIES; i++) {
+		if (blob->secid[i] == 0)
+			continue;
+		error = security_secid_to_secctx(blob, &lsmdata, i);
+		if (error && error != -EINVAL) {
+			audit_panic("error in audit_log_task_context");
+			return error;
+		}
+
+		audit_log_format(ab, " subj=%s", lsmdata.context);
+		security_release_secctx(&lsmdata);
+		break;
+	}
 
-error_path:
-	audit_panic("error in audit_log_task_context");
-	return error;
+	return 0;
 }
 EXPORT_SYMBOL(audit_log_task_context);
 
+int audit_log_object_context(struct audit_buffer *ab,
+				    struct lsmblob *blob)
+{
+	int i;
+	int error;
+	bool sep = false;
+	struct lsmcontext lsmdata;
+	struct audit_buffer *lsmab = NULL;
+	struct audit_context *context = NULL;
+
+	/*
+	 * If there is more than one security module that has a
+	 * object "context" it's necessary to put the object data
+	 * into a separate record to maintain compatibility.
+	 */
+	if (lsm_multiple_contexts()) {
+		audit_log_format(ab, " obj=?");
+		context = ab->ctx;
+		if (context)
+			lsmab = audit_log_start(context, GFP_KERNEL,
+						AUDIT_MAC_OBJ_CONTEXTS);
+	}
+
+	for (i = 0; i < LSMBLOB_ENTRIES; i++) {
+		if (blob->secid[i] == 0)
+			continue;
+		error = security_secid_to_secctx(blob, &lsmdata, i);
+		if (error && error != -EINVAL) {
+			audit_panic("error in audit_log_object_context");
+			return error;
+		}
+
+		if (context) {
+			audit_log_format(lsmab, "%sobj_%s=%s",
+					 sep ? " " : "",
+					 security_lsm_slot_name(i),
+					 lsmdata.context);
+			sep = true;
+		} else
+			audit_log_format(ab, " obj=%s", lsmdata.context);
+
+		security_release_secctx(&lsmdata);
+		if (!context)
+			break;
+	}
+
+	if (context)
+		audit_log_end(lsmab);
+
+	return 0;
+}
+EXPORT_SYMBOL(audit_log_object_context);
+
 void audit_log_d_path_exe(struct audit_buffer *ab,
 			  struct mm_struct *mm)
 {
@@ -2221,7 +2374,7 @@
 	audit_log_format(ab, " comm=");
 	audit_log_untrustedstring(ab, get_task_comm(comm, current));
 	audit_log_d_path_exe(ab, current->mm);
-	audit_log_task_context(ab);
+	audit_log_task_context(ab, NULL);
 }
 EXPORT_SYMBOL(audit_log_task_info);
 
@@ -2279,6 +2432,7 @@
 	if (!audit_enabled)
 		return;
 
+	audit_stamp_context(audit_context());
 	ab = audit_log_start(audit_context(), GFP_KERNEL, AUDIT_LOGIN);
 	if (!ab)
 		return;
@@ -2289,11 +2443,12 @@
 	tty = audit_get_tty();
 
 	audit_log_format(ab, "pid=%d uid=%u", task_tgid_nr(current), uid);
-	audit_log_task_context(ab);
+	audit_log_task_context(ab, NULL);
 	audit_log_format(ab, " old-auid=%u auid=%u tty=%s old-ses=%u ses=%u res=%d",
 			 oldloginuid, loginuid, tty ? tty_name(tty) : "(none)",
 			 oldsessionid, sessionid, !rc);
 	audit_put_tty(tty);
+	audit_log_lsm(NULL, true);
 	audit_log_end(ab);
 }
 
@@ -2353,7 +2508,7 @@
 			audit_sig_uid = auid;
 		else
 			audit_sig_uid = uid;
-		security_task_getsecid_subj(current, &audit_sig_sid);
+		security_task_getsecid_subj(current, &audit_sig_lsm);
 	}
 
 	return audit_signal_info_syscall(t);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/audit.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/audit.h
@@ -12,6 +12,7 @@
 #include <linux/fs.h>
 #include <linux/audit.h>
 #include <linux/skbuff.h>
+#include <linux/security.h>
 #include <uapi/linux/mqueue.h>
 #include <linux/tty.h>
 
@@ -80,7 +81,7 @@
 	kuid_t			uid;
 	kgid_t			gid;
 	dev_t			rdev;
-	u32			osid;
+	struct lsmblob		oblob;
 	struct audit_cap_data	fcap;
 	unsigned int		fcap_ver;
 	unsigned char		type;		/* record type */
@@ -137,7 +138,7 @@
 	kuid_t		    target_auid;
 	kuid_t		    target_uid;
 	unsigned int	    target_sessionid;
-	u32		    target_sid;
+	struct lsmblob	    target_lsm;
 	char		    target_comm[TASK_COMM_LEN];
 
 	struct audit_tree_refs *trees, *first_trees;
@@ -154,7 +155,7 @@
 			kuid_t			uid;
 			kgid_t			gid;
 			umode_t			mode;
-			u32			osid;
+			struct lsmblob		oblob;
 			int			has_perm;
 			uid_t			perm_uid;
 			gid_t			perm_gid;
@@ -194,6 +195,10 @@
 		struct {
 			char			*name;
 		} module;
+		struct {
+			struct audit_ntp_data	ntp_data;
+			struct timespec64	tk_injoffset;
+		} time;
 	};
 	int fds[2];
 	struct audit_proctitle proctitle;
@@ -330,6 +335,8 @@
 
 extern char *audit_unpack_string(void **bufp, size_t *remain, size_t len);
 
+extern struct lsmblob audit_sig_lsm;
+
 extern int audit_filter(int msgtype, unsigned int listtype);
 
 extern void audit_ctl_lock(void);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/audit_fsnotify.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/audit_fsnotify.c
@@ -100,8 +100,9 @@
 	audit_update_mark(audit_mark, dentry->d_inode);
 	audit_mark->rule = krule;
 
-	ret = fsnotify_add_inode_mark(&audit_mark->mark, inode, true);
+	ret = fsnotify_add_inode_mark(&audit_mark->mark, inode, 0);
 	if (ret < 0) {
+		audit_mark->path = NULL;
 		fsnotify_put_mark(&audit_mark->mark);
 		audit_mark = ERR_PTR(ret);
 	}
@@ -160,8 +161,7 @@
 
 	audit_mark = container_of(inode_mark, struct audit_fsnotify_mark, mark);
 
-	if (WARN_ON_ONCE(inode_mark->group != audit_fsnotify_group) ||
-	    WARN_ON_ONCE(!inode))
+	if (WARN_ON_ONCE(inode_mark->group != audit_fsnotify_group))
 		return 0;
 
 	if (mask & (FS_CREATE|FS_MOVED_TO|FS_DELETE|FS_MOVED_FROM)) {
@@ -182,7 +182,8 @@
 
 static int __init audit_fsnotify_init(void)
 {
-	audit_fsnotify_group = fsnotify_alloc_group(&audit_mark_fsnotify_ops);
+	audit_fsnotify_group = fsnotify_alloc_group(&audit_mark_fsnotify_ops,
+						    FSNOTIFY_GROUP_DUPS);
 	if (IS_ERR(audit_fsnotify_group)) {
 		audit_fsnotify_group = NULL;
 		audit_panic("cannot create audit fsnotify group");
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/audit_tree.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/audit_tree.c
@@ -1073,7 +1073,7 @@
 
 	audit_tree_mark_cachep = KMEM_CACHE(audit_tree_mark, SLAB_PANIC);
 
-	audit_tree_group = fsnotify_alloc_group(&audit_tree_ops);
+	audit_tree_group = fsnotify_alloc_group(&audit_tree_ops, 0);
 	if (IS_ERR(audit_tree_group))
 		audit_panic("cannot initialize fsnotify group for rectree watches");
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/audit_watch.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/audit_watch.c
@@ -472,8 +472,7 @@
 
 	parent = container_of(inode_mark, struct audit_parent, mark);
 
-	if (WARN_ON_ONCE(inode_mark->group != audit_watch_group) ||
-	    WARN_ON_ONCE(!inode))
+	if (WARN_ON_ONCE(inode_mark->group != audit_watch_group))
 		return 0;
 
 	if (mask & (FS_CREATE|FS_MOVED_TO) && inode)
@@ -493,7 +492,7 @@
 
 static int __init audit_watch_init(void)
 {
-	audit_watch_group = fsnotify_alloc_group(&audit_watch_fsnotify_ops);
+	audit_watch_group = fsnotify_alloc_group(&audit_watch_fsnotify_ops, 0);
 	if (IS_ERR(audit_watch_group)) {
 		audit_watch_group = NULL;
 		audit_panic("cannot create audit fsnotify group");
@@ -527,11 +526,18 @@
 	unsigned long ino;
 	dev_t dev;
 
-	exe_file = get_task_exe_file(tsk);
+	/* only do exe filtering if we are recording @current events/records */
+	if (tsk != current)
+		return 0;
+
+	if (!current->mm)
+		return 0;
+	exe_file = get_mm_exe_file(current->mm);
 	if (!exe_file)
 		return 0;
 	ino = file_inode(exe_file)->i_ino;
 	dev = file_inode(exe_file)->i_sb->s_dev;
 	fput(exe_file);
+
 	return audit_mark_compare(mark, ino, dev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/auditfilter.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/auditfilter.c
@@ -74,7 +74,7 @@
 	case AUDIT_OBJ_LEV_LOW:
 	case AUDIT_OBJ_LEV_HIGH:
 		kfree(f->lsm_str);
-		security_audit_rule_free(f->lsm_rule);
+		security_audit_rule_free(f->lsm_rules);
 	}
 }
 
@@ -519,9 +519,11 @@
 				goto exit_free;
 			}
 			entry->rule.buflen += f_val;
+			f->lsm_isset = true;
 			f->lsm_str = str;
 			err = security_audit_rule_init(f->type, f->op, str,
-						       (void **)&f->lsm_rule);
+						       f->lsm_rules,
+						       GFP_KERNEL);
 			/* Keep currently invalid fields around in case they
 			 * become valid after a policy reload. */
 			if (err == -EINVAL) {
@@ -774,7 +776,7 @@
 	return 0;
 }
 
-/* Duplicate LSM field information.  The lsm_rule is opaque, so must be
+/* Duplicate LSM field information.  The lsm_rules is opaque, so must be
  * re-initialized. */
 static inline int audit_dupe_lsm_field(struct audit_field *df,
 					   struct audit_field *sf)
@@ -788,9 +790,9 @@
 		return -ENOMEM;
 	df->lsm_str = lsm_str;
 
-	/* our own (refreshed) copy of lsm_rule */
+	/* our own (refreshed) copy of lsm_rules */
 	ret = security_audit_rule_init(df->type, df->op, df->lsm_str,
-				       (void **)&df->lsm_rule);
+				       df->lsm_rules, GFP_KERNEL);
 	/* Keep currently invalid fields around in case they
 	 * become valid after a policy reload. */
 	if (ret == -EINVAL) {
@@ -842,7 +844,7 @@
 	new->tree = old->tree;
 	memcpy(new->fields, old->fields, sizeof(struct audit_field) * fcount);
 
-	/* deep copy this information, updating the lsm_rule fields, because
+	/* deep copy this information, updating the lsm_rules fields, because
 	 * the originals will all be freed when the old rule is freed. */
 	for (i = 0; i < fcount; i++) {
 		switch (new->fields[i].type) {
@@ -1106,7 +1108,7 @@
 	if (!ab)
 		return;
 	audit_log_session_info(ab);
-	audit_log_task_context(ab);
+	audit_log_task_context(ab, NULL);
 	audit_log_format(ab, " op=%s", action);
 	audit_log_key(ab, rule->filterkey);
 	audit_log_format(ab, " list=%d res=%d", rule->listnr, res);
@@ -1329,7 +1331,7 @@
 		for (i = 0; i < e->rule.field_count; i++) {
 			struct audit_field *f = &e->rule.fields[i];
 			pid_t pid;
-			u32 sid;
+			struct lsmblob blob;
 
 			switch (f->type) {
 			case AUDIT_PID:
@@ -1358,11 +1360,11 @@
 			case AUDIT_SUBJ_TYPE:
 			case AUDIT_SUBJ_SEN:
 			case AUDIT_SUBJ_CLR:
-				if (f->lsm_rule) {
-					security_task_getsecid_subj(current,
-								    &sid);
-					result = security_audit_rule_match(sid,
-						   f->type, f->op, f->lsm_rule);
+				if (f->lsm_isset) {
+					security_task_getsecid_subj(current, &blob);
+					result = security_audit_rule_match(
+						   &blob, f->type, f->op,
+						   f->lsm_rules);
 				}
 				break;
 			case AUDIT_EXE:
@@ -1389,7 +1391,7 @@
 	return ret;
 }
 
-static int update_lsm_rule(struct audit_krule *r)
+static int update_lsm_rules(struct audit_krule *r)
 {
 	struct audit_entry *entry = container_of(r, struct audit_entry, rule);
 	struct audit_entry *nentry;
@@ -1421,7 +1423,7 @@
 	return err;
 }
 
-/* This function will re-initialize the lsm_rule field of all applicable rules.
+/* This function will re-initialize the lsm_rules field of all applicable rules.
  * It will traverse the filter lists serarching for rules that contain LSM
  * specific filter fields.  When such a rule is found, it is copied, the
  * LSM field is re-initialized, and the old rule is replaced with the
@@ -1436,7 +1438,7 @@
 
 	for (i = 0; i < AUDIT_NR_FILTERS; i++) {
 		list_for_each_entry_safe(r, n, &audit_rules_list[i], list) {
-			int res = update_lsm_rule(r);
+			int res = update_lsm_rules(r);
 			if (!err)
 				err = res;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/auditsc.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/auditsc.c
@@ -111,7 +111,7 @@
 	kuid_t			target_auid[AUDIT_AUX_PIDS];
 	kuid_t			target_uid[AUDIT_AUX_PIDS];
 	unsigned int		target_sessionid[AUDIT_AUX_PIDS];
-	u32			target_sid[AUDIT_AUX_PIDS];
+	struct lsmblob		target_lsm[AUDIT_AUX_PIDS];
 	char 			target_comm[AUDIT_AUX_PIDS][TASK_COMM_LEN];
 	int			pid_count;
 };
@@ -477,7 +477,7 @@
 {
 	const struct cred *cred;
 	int i, need_sid = 1;
-	u32 sid;
+	struct lsmblob blob = { };
 	unsigned int sessionid;
 
 	cred = rcu_dereference_check(tsk->cred, tsk == current || task_creation);
@@ -671,14 +671,15 @@
 			   match for now to avoid losing information that
 			   may be wanted.   An error message will also be
 			   logged upon error */
-			if (f->lsm_rule) {
+			if (f->lsm_isset) {
 				if (need_sid) {
-					security_task_getsecid_subj(tsk, &sid);
+					security_task_getsecid_subj(tsk, &blob);
 					need_sid = 0;
 				}
-				result = security_audit_rule_match(sid, f->type,
+				result = security_audit_rule_match(&blob,
+								   f->type,
 								   f->op,
-								   f->lsm_rule);
+								   f->lsm_rules);
 			}
 			break;
 		case AUDIT_OBJ_USER:
@@ -688,21 +689,21 @@
 		case AUDIT_OBJ_LEV_HIGH:
 			/* The above note for AUDIT_SUBJ_USER...AUDIT_SUBJ_CLR
 			   also applies here */
-			if (f->lsm_rule) {
+			if (f->lsm_isset) {
 				/* Find files that match */
 				if (name) {
 					result = security_audit_rule_match(
-								name->osid,
+								&blob,
 								f->type,
 								f->op,
-								f->lsm_rule);
+								f->lsm_rules);
 				} else if (ctx) {
 					list_for_each_entry(n, &ctx->names_list, list) {
 						if (security_audit_rule_match(
-								n->osid,
+								&blob,
 								f->type,
 								f->op,
-								f->lsm_rule)) {
+								f->lsm_rules)) {
 							++result;
 							break;
 						}
@@ -711,9 +712,9 @@
 				/* Find ipc objects that match */
 				if (!ctx || ctx->type != AUDIT_IPC)
 					break;
-				if (security_audit_rule_match(ctx->ipc.osid,
+				if (security_audit_rule_match(&ctx->ipc.oblob,
 							      f->type, f->op,
-							      f->lsm_rule))
+							      f->lsm_rules))
 					++result;
 			}
 			break;
@@ -956,10 +957,12 @@
 		return 0; /* Return if not auditing. */
 
 	state = audit_filter_task(tsk, &key);
-	if (state == AUDIT_STATE_DISABLED) {
+	if (!lsm_multiple_contexts() && state == AUDIT_STATE_DISABLED) {
 		clear_task_syscall_work(tsk, SYSCALL_AUDIT);
 		return 0;
 	}
+	if (state == AUDIT_STATE_DISABLED)
+		clear_task_syscall_work(tsk, SYSCALL_AUDIT);
 
 	if (!(context = audit_alloc_context(state))) {
 		kfree(key);
@@ -987,12 +990,11 @@
 }
 
 static int audit_log_pid_context(struct audit_context *context, pid_t pid,
-				 kuid_t auid, kuid_t uid, unsigned int sessionid,
-				 u32 sid, char *comm)
+				 kuid_t auid, kuid_t uid,
+				 unsigned int sessionid,
+				 struct lsmblob *blob, char *comm)
 {
 	struct audit_buffer *ab;
-	char *ctx = NULL;
-	u32 len;
 	int rc = 0;
 
 	ab = audit_log_start(context, GFP_KERNEL, AUDIT_OBJ_PID);
@@ -1002,15 +1004,7 @@
 	audit_log_format(ab, "opid=%d oauid=%d ouid=%d oses=%d", pid,
 			 from_kuid(&init_user_ns, auid),
 			 from_kuid(&init_user_ns, uid), sessionid);
-	if (sid) {
-		if (security_secid_to_secctx(sid, &ctx, &len)) {
-			audit_log_format(ab, " obj=(none)");
-			rc = 1;
-		} else {
-			audit_log_format(ab, " obj=%s", ctx);
-			security_release_secctx(ctx, len);
-		}
-	}
+	rc = audit_log_object_context(ab, blob);
 	audit_log_format(ab, " ocomm=");
 	audit_log_untrustedstring(ab, comm);
 	audit_log_end(ab);
@@ -1219,6 +1213,53 @@
 			 from_kuid(&init_user_ns, name->fcap.rootid));
 }
 
+static void audit_log_time(struct audit_context *context, struct audit_buffer **ab)
+{
+	const struct audit_ntp_data *ntp = &context->time.ntp_data;
+	const struct timespec64 *tk = &context->time.tk_injoffset;
+	static const char * const ntp_name[] = {
+		"offset",
+		"freq",
+		"status",
+		"tai",
+		"tick",
+		"adjust",
+	};
+	int type;
+
+	if (context->type == AUDIT_TIME_ADJNTPVAL) {
+		for (type = 0; type < AUDIT_NTP_NVALS; type++) {
+			if (ntp->vals[type].newval != ntp->vals[type].oldval) {
+				if (!*ab) {
+					*ab = audit_log_start(context,
+							GFP_KERNEL,
+							AUDIT_TIME_ADJNTPVAL);
+					if (!*ab)
+						return;
+				}
+				audit_log_format(*ab, "op=%s old=%lli new=%lli",
+						 ntp_name[type],
+						 ntp->vals[type].oldval,
+						 ntp->vals[type].newval);
+				audit_log_end(*ab);
+				*ab = NULL;
+			}
+		}
+	}
+	if (tk->tv_sec != 0 || tk->tv_nsec != 0) {
+		if (!*ab) {
+			*ab = audit_log_start(context, GFP_KERNEL,
+					      AUDIT_TIME_INJOFFSET);
+			if (!*ab)
+				return;
+		}
+		audit_log_format(*ab, "sec=%lli nsec=%li",
+				 (long long)tk->tv_sec, tk->tv_nsec);
+		audit_log_end(*ab);
+		*ab = NULL;
+	}
+}
+
 static void show_special(struct audit_context *context, int *call_panic)
 {
 	struct audit_buffer *ab;
@@ -1238,24 +1279,14 @@
 				context->socketcall.args[i]);
 		break; }
 	case AUDIT_IPC: {
-		u32 osid = context->ipc.osid;
+		struct lsmblob *oblob = &context->ipc.oblob;
 
 		audit_log_format(ab, "ouid=%u ogid=%u mode=%#ho",
 				 from_kuid(&init_user_ns, context->ipc.uid),
 				 from_kgid(&init_user_ns, context->ipc.gid),
 				 context->ipc.mode);
-		if (osid) {
-			char *ctx = NULL;
-			u32 len;
-
-			if (security_secid_to_secctx(osid, &ctx, &len)) {
-				audit_log_format(ab, " osid=%u", osid);
-				*call_panic = 1;
-			} else {
-				audit_log_format(ab, " obj=%s", ctx);
-				security_release_secctx(ctx, len);
-			}
-		}
+		if (audit_log_object_context(ab, oblob))
+			*call_panic = 1;
 		if (context->ipc.has_perm) {
 			audit_log_end(ab);
 			ab = audit_log_start(context, GFP_KERNEL,
@@ -1327,6 +1358,11 @@
 			audit_log_format(ab, "(null)");
 
 		break;
+	case AUDIT_TIME_ADJNTPVAL:
+	case AUDIT_TIME_INJOFFSET:
+		/* this call deviates from the rest, eating the buffer */
+		audit_log_time(context, &ab);
+		break;
 	}
 	audit_log_end(ab);
 }
@@ -1400,20 +1436,8 @@
 				 from_kgid(&init_user_ns, n->gid),
 				 MAJOR(n->rdev),
 				 MINOR(n->rdev));
-	if (n->osid != 0) {
-		char *ctx = NULL;
-		u32 len;
-
-		if (security_secid_to_secctx(
-			n->osid, &ctx, &len)) {
-			audit_log_format(ab, " osid=%u", n->osid);
-			if (call_panic)
-				*call_panic = 2;
-		} else {
-			audit_log_format(ab, " obj=%s", ctx);
-			security_release_secctx(ctx, len);
-		}
-	}
+	if (audit_log_object_context(ab, &n->oblob) && call_panic)
+		*call_panic = 2;
 
 	/* log the audit_names record type */
 	switch (n->type) {
@@ -1479,6 +1503,53 @@
 	audit_log_end(ab);
 }
 
+void audit_log_lsm(struct lsmblob *blob, bool exiting)
+{
+	struct audit_context *context = audit_context();
+	struct lsmcontext lsmdata;
+	struct audit_buffer *ab;
+	struct lsmblob localblob;
+	bool sep = false;
+	int error;
+	int i;
+
+	if (!lsm_multiple_contexts())
+		return;
+
+	if (context && context->in_syscall && !exiting)
+		return;
+
+	ab = audit_log_start(context, GFP_ATOMIC, AUDIT_MAC_TASK_CONTEXTS);
+	if (!ab)
+		return;	/* audit_panic or being filtered */
+
+	if (blob == NULL) {
+		security_task_getsecid_subj(current, &localblob);
+		if (!lsmblob_is_set(&localblob))
+			goto end;
+		blob = &localblob;
+	}
+
+	for (i = 0; i < LSMBLOB_ENTRIES; i++) {
+		if (blob->secid[i] == 0)
+			continue;
+		error = security_secid_to_secctx(blob, &lsmdata, i);
+		if (error && error != -EINVAL) {
+			audit_panic("error in audit_log_lsm");
+			goto end;
+		}
+
+		audit_log_format(ab, "%ssubj_%s=%s", sep ? " " : "",
+				 security_lsm_slot_name(i), lsmdata.context);
+		sep = true;
+
+		security_release_secctx(&lsmdata);
+	}
+
+end:
+	audit_log_end(ab);
+}
+
 static void audit_log_exit(void)
 {
 	int i, call_panic = 0;
@@ -1575,7 +1646,7 @@
 						  axs->target_auid[i],
 						  axs->target_uid[i],
 						  axs->target_sessionid[i],
-						  axs->target_sid[i],
+						  &axs->target_lsm[i],
 						  axs->target_comm[i]))
 				call_panic = 1;
 	}
@@ -1584,7 +1655,7 @@
 	    audit_log_pid_context(context, context->target_pid,
 				  context->target_auid, context->target_uid,
 				  context->target_sessionid,
-				  context->target_sid, context->target_comm))
+				  &context->target_lsm, context->target_comm))
 			call_panic = 1;
 
 	if (context->pwd.dentry && context->pwd.mnt) {
@@ -1603,6 +1674,7 @@
 	}
 
 	audit_log_proctitle();
+	audit_log_lsm(NULL, true);
 
 	/* Send end of event record to help user space know we are finished */
 	ab = audit_log_start(context, GFP_KERNEL, AUDIT_EOE);
@@ -1760,7 +1832,7 @@
 	context->aux = NULL;
 	context->aux_pids = NULL;
 	context->target_pid = 0;
-	context->target_sid = 0;
+	lsmblob_init(&context->target_lsm, 0);
 	context->sockaddr_len = 0;
 	context->type = 0;
 	context->fds[0] = -1;
@@ -1966,7 +2038,7 @@
 	name->uid   = inode->i_uid;
 	name->gid   = inode->i_gid;
 	name->rdev  = inode->i_rdev;
-	security_inode_getsecid(inode, &name->osid);
+	security_inode_getsecid(inode, &name->oblob);
 	if (flags & AUDIT_INODE_NOEVAL) {
 		name->fcap_ver = -1;
 		return;
@@ -2148,6 +2220,8 @@
 		}
 	}
 
+	cond_resched();
+
 	/* is there a matching child entry? */
 	list_for_each_entry(n, &context->names_list, list) {
 		/* can only match entries that have a name */
@@ -2198,6 +2272,21 @@
 EXPORT_SYMBOL_GPL(__audit_inode_child);
 
 /**
+ * audit_stamp_context - set the timestamp+serial in an audit context
+ * @ctx: audit_context to set
+ */
+void audit_stamp_context(struct audit_context *ctx)
+{
+	/* ctx will be NULL unless lsm_multiple_contexts() is true */
+	if (!ctx)
+		return;
+
+	ktime_get_coarse_real_ts64(&ctx->ctime);
+	ctx->serial = audit_serial();
+	ctx->current_state = AUDIT_STATE_BUILD;
+}
+ 
+/**
  * auditsc_get_stamp - get local copies of audit_context values
  * @ctx: audit_context for the task
  * @t: timespec64 to store time recorded in the audit_context
@@ -2208,6 +2297,12 @@
 int auditsc_get_stamp(struct audit_context *ctx,
 		       struct timespec64 *t, unsigned int *serial)
 {
+	if (ctx->serial && !ctx->in_syscall) {
+		t->tv_sec  = ctx->ctime.tv_sec;
+		t->tv_nsec = ctx->ctime.tv_nsec;
+		*serial    = ctx->serial;
+		return 1;
+	}
 	if (!ctx->in_syscall)
 		return 0;
 	if (!ctx->serial)
@@ -2313,12 +2408,11 @@
 void __audit_ipc_obj(struct kern_ipc_perm *ipcp)
 {
 	struct audit_context *context = audit_context();
-
 	context->ipc.uid = ipcp->uid;
 	context->ipc.gid = ipcp->gid;
 	context->ipc.mode = ipcp->mode;
 	context->ipc.has_perm = 0;
-	security_ipc_getsecid(ipcp, &context->ipc.osid);
+	security_ipc_getsecid(ipcp, &context->ipc.oblob);
 	context->type = AUDIT_IPC;
 }
 
@@ -2415,7 +2509,7 @@
 	context->target_auid = audit_get_loginuid(t);
 	context->target_uid = task_uid(t);
 	context->target_sessionid = audit_get_sessionid(t);
-	security_task_getsecid_obj(t, &context->target_sid);
+	security_task_getsecid_obj(t, &context->target_lsm);
 	memcpy(context->target_comm, t->comm, TASK_COMM_LEN);
 }
 
@@ -2442,7 +2536,7 @@
 		ctx->target_auid = audit_get_loginuid(t);
 		ctx->target_uid = t_uid;
 		ctx->target_sessionid = audit_get_sessionid(t);
-		security_task_getsecid_obj(t, &ctx->target_sid);
+		security_task_getsecid_obj(t, &ctx->target_lsm);
 		memcpy(ctx->target_comm, t->comm, TASK_COMM_LEN);
 		return 0;
 	}
@@ -2463,7 +2557,7 @@
 	axp->target_auid[axp->pid_count] = audit_get_loginuid(t);
 	axp->target_uid[axp->pid_count] = t_uid;
 	axp->target_sessionid[axp->pid_count] = audit_get_sessionid(t);
-	security_task_getsecid_obj(t, &axp->target_sid[axp->pid_count]);
+	security_task_getsecid_obj(t, &axp->target_lsm[axp->pid_count]);
 	memcpy(axp->target_comm[axp->pid_count], t->comm, TASK_COMM_LEN);
 	axp->pid_count++;
 
@@ -2564,31 +2658,26 @@
 
 void __audit_tk_injoffset(struct timespec64 offset)
 {
-	audit_log(audit_context(), GFP_KERNEL, AUDIT_TIME_INJOFFSET,
-		  "sec=%lli nsec=%li",
-		  (long long)offset.tv_sec, offset.tv_nsec);
-}
-
-static void audit_log_ntp_val(const struct audit_ntp_data *ad,
-			      const char *op, enum audit_ntp_type type)
-{
-	const struct audit_ntp_val *val = &ad->vals[type];
-
-	if (val->newval == val->oldval)
-		return;
+	struct audit_context *context = audit_context();
 
-	audit_log(audit_context(), GFP_KERNEL, AUDIT_TIME_ADJNTPVAL,
-		  "op=%s old=%lli new=%lli", op, val->oldval, val->newval);
+	/* only set type if not already set by NTP */
+	if (!context->type)
+		context->type = AUDIT_TIME_INJOFFSET;
+	memcpy(&context->time.tk_injoffset, &offset, sizeof(offset));
 }
 
 void __audit_ntp_log(const struct audit_ntp_data *ad)
 {
-	audit_log_ntp_val(ad, "offset",	AUDIT_NTP_OFFSET);
-	audit_log_ntp_val(ad, "freq",	AUDIT_NTP_FREQ);
-	audit_log_ntp_val(ad, "status",	AUDIT_NTP_STATUS);
-	audit_log_ntp_val(ad, "tai",	AUDIT_NTP_TAI);
-	audit_log_ntp_val(ad, "tick",	AUDIT_NTP_TICK);
-	audit_log_ntp_val(ad, "adjust",	AUDIT_NTP_ADJUST);
+	struct audit_context *context = audit_context();
+	int type;
+
+	for (type = 0; type < AUDIT_NTP_NVALS; type++)
+		if (ad->vals[type].newval != ad->vals[type].oldval) {
+			/* unconditionally set type, overwriting TK */
+			context->type = AUDIT_TIME_ADJNTPVAL;
+			memcpy(&context->time.ntp_data, ad, sizeof(*ad));
+			break;
+		}
 }
 
 void __audit_log_nfcfg(const char *name, u8 af, unsigned int nentries,
@@ -2604,7 +2693,7 @@
 			 name, af, nentries, audit_nfcfgs[op].s);
 
 	audit_log_format(ab, " pid=%u", task_pid_nr(current));
-	audit_log_task_context(ab); /* subj= */
+	audit_log_task_context(ab, NULL); /* subj= */
 	audit_log_format(ab, " comm=");
 	audit_log_untrustedstring(ab, get_task_comm(comm, current));
 	audit_log_end(ab);
@@ -2627,7 +2716,7 @@
 			 from_kuid(&init_user_ns, uid),
 			 from_kgid(&init_user_ns, gid),
 			 sessionid);
-	audit_log_task_context(ab);
+	audit_log_task_context(ab, NULL);
 	audit_log_format(ab, " pid=%d comm=", task_tgid_nr(current));
 	audit_log_untrustedstring(ab, get_task_comm(comm, current));
 	audit_log_d_path_exe(ab, current->mm);
@@ -2650,11 +2739,13 @@
 	if (signr == SIGQUIT)	/* don't care for those */
 		return;
 
+	audit_stamp_context(audit_context());
 	ab = audit_log_start(audit_context(), GFP_KERNEL, AUDIT_ANOM_ABEND);
 	if (unlikely(!ab))
 		return;
 	audit_log_task(ab);
 	audit_log_format(ab, " sig=%ld res=1", signr);
+	audit_log_lsm(NULL, true);
 	audit_log_end(ab);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bounds.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bounds.c
@@ -19,7 +19,7 @@
 	DEFINE(NR_PAGEFLAGS, __NR_PAGEFLAGS);
 	DEFINE(MAX_NR_ZONES, __MAX_NR_ZONES);
 #ifdef CONFIG_SMP
-	DEFINE(NR_CPUS_BITS, ilog2(CONFIG_NR_CPUS));
+	DEFINE(NR_CPUS_BITS, order_base_2(CONFIG_NR_CPUS));
 #endif
 	DEFINE(SPINLOCK_SIZE, sizeof(spinlock_t));
 	/* End of constants */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/arraymap.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/arraymap.c
@@ -74,6 +74,9 @@
 		 * access the elements.
 		 */
 		return -E2BIG;
+	/* percpu map value size is bound by PCPU_MIN_UNIT_SIZE */
+	if (percpu && round_up(attr->value_size, 8) > PCPU_MIN_UNIT_SIZE)
+		return -E2BIG;
 
 	return 0;
 }
@@ -620,6 +623,11 @@
 		seq_info->percpu_value_buf = value_buf;
 	}
 
+	/* bpf_iter_attach_map() acquires a map uref, and the uref may be
+	 * released before or in the middle of iterating map elements, so
+	 * acquire an extra map uref for iterator.
+	 */
+	bpf_map_inc_with_uref(map);
 	seq_info->map = map;
 	return 0;
 }
@@ -628,6 +636,7 @@
 {
 	struct bpf_iter_seq_array_map_info *seq_info = priv_data;
 
+	bpf_map_put_with_uref(seq_info->map);
 	kfree(seq_info->percpu_value_buf);
 }
 
@@ -805,7 +814,7 @@
 	}
 
 	if (old_ptr)
-		map->ops->map_fd_put_ptr(old_ptr);
+		map->ops->map_fd_put_ptr(map, old_ptr, true);
 	return 0;
 }
 
@@ -828,7 +837,7 @@
 	}
 
 	if (old_ptr) {
-		map->ops->map_fd_put_ptr(old_ptr);
+		map->ops->map_fd_put_ptr(map, old_ptr, true);
 		return 0;
 	} else {
 		return -ENOENT;
@@ -852,8 +861,9 @@
 	return prog;
 }
 
-static void prog_fd_array_put_ptr(void *ptr)
+static void prog_fd_array_put_ptr(struct bpf_map *map, void *ptr, bool need_defer)
 {
+	/* bpf_prog is freed after one RCU or tasks trace grace period */
 	bpf_prog_put(ptr);
 }
 
@@ -951,11 +961,16 @@
 	mutex_unlock(&aux->poke_mutex);
 }
 
+void __weak bpf_arch_poke_desc_update(struct bpf_jit_poke_descriptor *poke,
+				      struct bpf_prog *new, struct bpf_prog *old)
+{
+	WARN_ON_ONCE(1);
+}
+
 static void prog_array_map_poke_run(struct bpf_map *map, u32 key,
 				    struct bpf_prog *old,
 				    struct bpf_prog *new)
 {
-	u8 *old_addr, *new_addr, *old_bypass_addr;
 	struct prog_poke_elem *elem;
 	struct bpf_array_aux *aux;
 
@@ -964,7 +979,7 @@
 
 	list_for_each_entry(elem, &aux->poke_progs, list) {
 		struct bpf_jit_poke_descriptor *poke;
-		int i, ret;
+		int i;
 
 		for (i = 0; i < elem->aux->size_poke_tab; i++) {
 			poke = &elem->aux->poke_tab[i];
@@ -983,21 +998,10 @@
 			 *    activated, so tail call updates can arrive from here
 			 *    while JIT is still finishing its final fixup for
 			 *    non-activated poke entries.
-			 * 3) On program teardown, the program's kallsym entry gets
-			 *    removed out of RCU callback, but we can only untrack
-			 *    from sleepable context, therefore bpf_arch_text_poke()
-			 *    might not see that this is in BPF text section and
-			 *    bails out with -EINVAL. As these are unreachable since
-			 *    RCU grace period already passed, we simply skip them.
-			 * 4) Also programs reaching refcount of zero while patching
+			 * 3) Also programs reaching refcount of zero while patching
 			 *    is in progress is okay since we're protected under
 			 *    poke_mutex and untrack the programs before the JIT
-			 *    buffer is freed. When we're still in the middle of
-			 *    patching and suddenly kallsyms entry of the program
-			 *    gets evicted, we just skip the rest which is fine due
-			 *    to point 3).
-			 * 5) Any other error happening below from bpf_arch_text_poke()
-			 *    is a unexpected bug.
+			 *    buffer is freed.
 			 */
 			if (!READ_ONCE(poke->tailcall_target_stable))
 				continue;
@@ -1007,39 +1011,7 @@
 			    poke->tail_call.key != key)
 				continue;
 
-			old_bypass_addr = old ? NULL : poke->bypass_addr;
-			old_addr = old ? (u8 *)old->bpf_func + poke->adj_off : NULL;
-			new_addr = new ? (u8 *)new->bpf_func + poke->adj_off : NULL;
-
-			if (new) {
-				ret = bpf_arch_text_poke(poke->tailcall_target,
-							 BPF_MOD_JUMP,
-							 old_addr, new_addr);
-				BUG_ON(ret < 0 && ret != -EINVAL);
-				if (!old) {
-					ret = bpf_arch_text_poke(poke->tailcall_bypass,
-								 BPF_MOD_JUMP,
-								 poke->bypass_addr,
-								 NULL);
-					BUG_ON(ret < 0 && ret != -EINVAL);
-				}
-			} else {
-				ret = bpf_arch_text_poke(poke->tailcall_bypass,
-							 BPF_MOD_JUMP,
-							 old_bypass_addr,
-							 poke->bypass_addr);
-				BUG_ON(ret < 0 && ret != -EINVAL);
-				/* let other CPUs finish the execution of program
-				 * so that it will not possible to expose them
-				 * to invalid nop, stack unwind, nop state
-				 */
-				if (!ret)
-					synchronize_rcu();
-				ret = bpf_arch_text_poke(poke->tailcall_target,
-							 BPF_MOD_JUMP,
-							 old_addr, NULL);
-				BUG_ON(ret < 0 && ret != -EINVAL);
-			}
+			bpf_arch_poke_desc_update(poke, new, old);
 		}
 	}
 }
@@ -1180,8 +1152,9 @@
 	return ee;
 }
 
-static void perf_event_fd_array_put_ptr(void *ptr)
+static void perf_event_fd_array_put_ptr(struct bpf_map *map, void *ptr, bool need_defer)
 {
+	/* bpf_perf_event is freed after one RCU grace period */
 	bpf_event_entry_free_rcu(ptr);
 }
 
@@ -1236,7 +1209,7 @@
 	return cgroup_get_from_fd(fd);
 }
 
-static void cgroup_fd_array_put_ptr(void *ptr)
+static void cgroup_fd_array_put_ptr(struct bpf_map *map, void *ptr, bool need_defer)
 {
 	/* cgroup_put free cgrp after a rcu grace period */
 	cgroup_put(ptr);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/bpf_local_storage.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/bpf_local_storage.c
@@ -48,11 +48,21 @@
 	return map->ops->map_owner_storage_ptr(owner);
 }
 
+static bool selem_linked_to_storage_lockless(const struct bpf_local_storage_elem *selem)
+{
+	return !hlist_unhashed_lockless(&selem->snode);
+}
+
 static bool selem_linked_to_storage(const struct bpf_local_storage_elem *selem)
 {
 	return !hlist_unhashed(&selem->snode);
 }
 
+static bool selem_linked_to_map_lockless(const struct bpf_local_storage_elem *selem)
+{
+	return !hlist_unhashed_lockless(&selem->map_node);
+}
+
 static bool selem_linked_to_map(const struct bpf_local_storage_elem *selem)
 {
 	return !hlist_unhashed(&selem->map_node);
@@ -71,7 +81,7 @@
 				GFP_ATOMIC | __GFP_NOWARN);
 	if (selem) {
 		if (value)
-			memcpy(SDATA(selem)->data, value, smap->map.value_size);
+			copy_map_value(&smap->map, SDATA(selem)->data, value);
 		return selem;
 	}
 
@@ -142,7 +152,7 @@
 	bool free_local_storage = false;
 	unsigned long flags;
 
-	if (unlikely(!selem_linked_to_storage(selem)))
+	if (unlikely(!selem_linked_to_storage_lockless(selem)))
 		/* selem has already been unlinked from sk */
 		return;
 
@@ -170,7 +180,7 @@
 	struct bpf_local_storage_map_bucket *b;
 	unsigned long flags;
 
-	if (unlikely(!selem_linked_to_map(selem)))
+	if (unlikely(!selem_linked_to_map_lockless(selem)))
 		/* selem has already be unlinked from smap */
 		return;
 
@@ -373,7 +383,7 @@
 		err = check_flags(old_sdata, map_flags);
 		if (err)
 			return ERR_PTR(err);
-		if (old_sdata && selem_linked_to_storage(SELEM(old_sdata))) {
+		if (old_sdata && selem_linked_to_storage_lockless(SELEM(old_sdata))) {
 			copy_map_value_locked(&smap->map, old_sdata->data,
 					      value, false);
 			return old_sdata;
@@ -506,11 +516,11 @@
 				struct bpf_local_storage_elem, map_node))) {
 			if (busy_counter) {
 				migrate_disable();
-				__this_cpu_inc(*busy_counter);
+				this_cpu_inc(*busy_counter);
 			}
 			bpf_selem_unlink(selem);
 			if (busy_counter) {
-				__this_cpu_dec(*busy_counter);
+				this_cpu_dec(*busy_counter);
 				migrate_enable();
 			}
 			cond_resched_rcu();
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/bpf_lru_list.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/bpf_lru_list.c
@@ -41,7 +41,12 @@
 /* bpf_lru_node helpers */
 static bool bpf_lru_node_is_ref(const struct bpf_lru_node *node)
 {
-	return node->ref;
+	return READ_ONCE(node->ref);
+}
+
+static void bpf_lru_node_clear_ref(struct bpf_lru_node *node)
+{
+	WRITE_ONCE(node->ref, 0);
 }
 
 static void bpf_lru_list_count_inc(struct bpf_lru_list *l,
@@ -89,7 +94,7 @@
 
 	bpf_lru_list_count_inc(l, tgt_type);
 	node->type = tgt_type;
-	node->ref = 0;
+	bpf_lru_node_clear_ref(node);
 	list_move(&node->list, &l->lists[tgt_type]);
 }
 
@@ -110,7 +115,7 @@
 		bpf_lru_list_count_inc(l, tgt_type);
 		node->type = tgt_type;
 	}
-	node->ref = 0;
+	bpf_lru_node_clear_ref(node);
 
 	/* If the moving node is the next_inactive_rotation candidate,
 	 * move the next_inactive_rotation pointer also.
@@ -353,7 +358,7 @@
 	*(u32 *)((void *)node + lru->hash_offset) = hash;
 	node->cpu = cpu;
 	node->type = BPF_LRU_LOCAL_LIST_T_PENDING;
-	node->ref = 0;
+	bpf_lru_node_clear_ref(node);
 	list_add(&node->list, local_pending_list(loc_l));
 }
 
@@ -419,7 +424,7 @@
 	if (!list_empty(free_list)) {
 		node = list_first_entry(free_list, struct bpf_lru_node, list);
 		*(u32 *)((void *)node + lru->hash_offset) = hash;
-		node->ref = 0;
+		bpf_lru_node_clear_ref(node);
 		__bpf_lru_node_move(l, node, BPF_LRU_LIST_T_INACTIVE);
 	}
 
@@ -522,7 +527,7 @@
 		}
 
 		node->type = BPF_LRU_LOCAL_LIST_T_FREE;
-		node->ref = 0;
+		bpf_lru_node_clear_ref(node);
 		list_move(&node->list, local_free_list(loc_l));
 
 		raw_spin_unlock_irqrestore(&loc_l->lock, flags);
@@ -568,7 +573,7 @@
 
 		node = (struct bpf_lru_node *)(buf + node_offset);
 		node->type = BPF_LRU_LIST_T_FREE;
-		node->ref = 0;
+		bpf_lru_node_clear_ref(node);
 		list_add(&node->list, &l->lists[BPF_LRU_LIST_T_FREE]);
 		buf += elem_size;
 	}
@@ -594,7 +599,7 @@
 		node = (struct bpf_lru_node *)(buf + node_offset);
 		node->cpu = cpu;
 		node->type = BPF_LRU_LIST_T_FREE;
-		node->ref = 0;
+		bpf_lru_node_clear_ref(node);
 		list_add(&node->list, &l->lists[BPF_LRU_LIST_T_FREE]);
 		i++;
 		buf += elem_size;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/bpf_lru_list.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/bpf_lru_list.h
@@ -63,11 +63,8 @@
 
 static inline void bpf_lru_node_set_ref(struct bpf_lru_node *node)
 {
-	/* ref is an approximation on access frequency.  It does not
-	 * have to be very accurate.  Hence, no protection is used.
-	 */
-	if (!node->ref)
-		node->ref = 1;
+	if (!READ_ONCE(node->ref))
+		WRITE_ONCE(node->ref, 1);
 }
 
 int bpf_lru_init(struct bpf_lru *lru, bool percpu, u32 hash_offset,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/bpf_task_storage.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/bpf_task_storage.c
@@ -25,20 +25,20 @@
 static void bpf_task_storage_lock(void)
 {
 	migrate_disable();
-	__this_cpu_inc(bpf_task_storage_busy);
+	this_cpu_inc(bpf_task_storage_busy);
 }
 
 static void bpf_task_storage_unlock(void)
 {
-	__this_cpu_dec(bpf_task_storage_busy);
+	this_cpu_dec(bpf_task_storage_busy);
 	migrate_enable();
 }
 
 static bool bpf_task_storage_trylock(void)
 {
 	migrate_disable();
-	if (unlikely(__this_cpu_inc_return(bpf_task_storage_busy) != 1)) {
-		__this_cpu_dec(bpf_task_storage_busy);
+	if (unlikely(this_cpu_inc_return(bpf_task_storage_busy) != 1)) {
+		this_cpu_dec(bpf_task_storage_busy);
 		migrate_enable();
 		return false;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/btf.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/btf.c
@@ -349,7 +349,7 @@
 struct btf_show {
 	u64 flags;
 	void *target;	/* target of show operation (seq file, buffer) */
-	void (*showfn)(struct btf_show *show, const char *fmt, va_list args);
+	__printf(2, 0) void (*showfn)(struct btf_show *show, const char *fmt, va_list args);
 	const struct btf *btf;
 	/* below are used during iteration */
 	struct {
@@ -633,13 +633,12 @@
 	return offset < btf->hdr.str_len;
 }
 
-static bool __btf_name_char_ok(char c, bool first, bool dot_ok)
+static bool __btf_name_char_ok(char c, bool first)
 {
 	if ((first ? !isalpha(c) :
 		     !isalnum(c)) &&
 	    c != '_' &&
-	    ((c == '.' && !dot_ok) ||
-	      c != '.'))
+	    c != '.')
 		return false;
 	return true;
 }
@@ -656,20 +655,20 @@
 	return NULL;
 }
 
-static bool __btf_name_valid(const struct btf *btf, u32 offset, bool dot_ok)
+static bool __btf_name_valid(const struct btf *btf, u32 offset)
 {
 	/* offset must be valid */
 	const char *src = btf_str_by_offset(btf, offset);
 	const char *src_limit;
 
-	if (!__btf_name_char_ok(*src, true, dot_ok))
+	if (!__btf_name_char_ok(*src, true))
 		return false;
 
 	/* set a limit on identifier length */
 	src_limit = src + KSYM_NAME_LEN;
 	src++;
 	while (*src && src < src_limit) {
-		if (!__btf_name_char_ok(*src, false, dot_ok))
+		if (!__btf_name_char_ok(*src, false))
 			return false;
 		src++;
 	}
@@ -677,17 +676,14 @@
 	return !*src;
 }
 
-/* Only C-style identifier is permitted. This can be relaxed if
- * necessary.
- */
 static bool btf_name_valid_identifier(const struct btf *btf, u32 offset)
 {
-	return __btf_name_valid(btf, offset, false);
+	return __btf_name_valid(btf, offset);
 }
 
 static bool btf_name_valid_section(const struct btf *btf, u32 offset)
 {
-	return __btf_name_valid(btf, offset, true);
+	return __btf_name_valid(btf, offset);
 }
 
 static const char *__btf_name_by_offset(const struct btf *btf, u32 offset)
@@ -2983,7 +2979,7 @@
 	if (v->next_member) {
 		const struct btf_type *last_member_type;
 		const struct btf_member *last_member;
-		u16 last_member_type_id;
+		u32 last_member_type_id;
 
 		last_member = btf_type_member(v->t) + v->next_member - 1;
 		last_member_type_id = last_member->type;
@@ -3536,7 +3532,7 @@
 	}
 
 	if (!t->name_off ||
-	    !__btf_name_valid(env->btf, t->name_off, true)) {
+	    !__btf_name_valid(env->btf, t->name_off)) {
 		btf_verifier_log_type(env, t, "Invalid name");
 		return -EINVAL;
 	}
@@ -3655,6 +3651,7 @@
 	struct btf *btf = env->btf;
 	u16 i;
 
+	env->resolve_mode = RESOLVE_TBD;
 	for_each_vsi_from(i, v->next_member, v->t, vsi) {
 		u32 var_type_id = vsi->type, type_id, type_size = 0;
 		const struct btf_type *var_type = btf_type_by_id(env->btf,
@@ -3864,6 +3861,11 @@
 			break;
 		}
 
+		if (btf_type_is_resolve_source_only(arg_type)) {
+			btf_verifier_log_type(env, t, "Invalid arg#%u", i + 1);
+			return -EINVAL;
+		}
+
 		if (args[i].name_off &&
 		    (!btf_name_offset_valid(btf, args[i].name_off) ||
 		     !btf_name_valid_identifier(btf, args[i].name_off))) {
@@ -4332,8 +4334,7 @@
 		log->len_total = log_size;
 
 		/* log attributes have to be sane */
-		if (log->len_total < 128 || log->len_total > UINT_MAX >> 8 ||
-		    !log->level || !log->ubuf) {
+		if (!bpf_verifier_log_attr_valid(log)) {
 			err = -EINVAL;
 			goto errout;
 		}
@@ -4464,6 +4465,7 @@
 	if (!ctx_struct)
 		/* should not happen */
 		return NULL;
+again:
 	ctx_tname = btf_name_by_offset(btf_vmlinux, ctx_struct->name_off);
 	if (!ctx_tname) {
 		/* should not happen */
@@ -4477,8 +4479,16 @@
 	 * int socket_filter_bpf_prog(struct __sk_buff *skb)
 	 * { // no fields of skb are ever used }
 	 */
-	if (strcmp(ctx_tname, tname))
-		return NULL;
+	if (strcmp(ctx_tname, tname)) {
+		/* bpf_user_pt_regs_t is a typedef, so resolve it to
+		 * underlying struct and check name again
+		 */
+		if (!btf_type_is_modifier(ctx_struct))
+			return NULL;
+		while (btf_type_is_modifier(ctx_struct))
+			ctx_struct = btf_type_by_id(btf_vmlinux, ctx_struct->type);
+		goto again;
+	}
 	return ctx_type;
 }
 
@@ -4801,10 +4811,12 @@
 	/* check for PTR_TO_RDONLY_BUF_OR_NULL or PTR_TO_RDWR_BUF_OR_NULL */
 	for (i = 0; i < prog->aux->ctx_arg_info_size; i++) {
 		const struct bpf_ctx_arg_aux *ctx_arg_info = &prog->aux->ctx_arg_info[i];
+		u32 type, flag;
 
-		if (ctx_arg_info->offset == off &&
-		    (ctx_arg_info->reg_type == PTR_TO_RDONLY_BUF_OR_NULL ||
-		     ctx_arg_info->reg_type == PTR_TO_RDWR_BUF_OR_NULL)) {
+		type = base_type(ctx_arg_info->reg_type);
+		flag = type_flag(ctx_arg_info->reg_type);
+		if (ctx_arg_info->offset == off && type == PTR_TO_BUF &&
+		    (flag & PTR_MAYBE_NULL)) {
 			info->reg_type = ctx_arg_info->reg_type;
 			return true;
 		}
@@ -5435,12 +5447,55 @@
 #endif
 };
 
+/* Returns true if struct is composed of scalars, 4 levels of nesting allowed */
+static bool __btf_type_is_scalar_struct(struct bpf_verifier_log *log,
+					const struct btf *btf,
+					const struct btf_type *t, int rec)
+{
+	const struct btf_type *member_type;
+	const struct btf_member *member;
+	u32 i;
+
+	if (!btf_type_is_struct(t))
+		return false;
+
+	for_each_member(i, t, member) {
+		const struct btf_array *array;
+
+		member_type = btf_type_skip_modifiers(btf, member->type, NULL);
+		if (btf_type_is_struct(member_type)) {
+			if (rec >= 3) {
+				bpf_log(log, "max struct nesting depth exceeded\n");
+				return false;
+			}
+			if (!__btf_type_is_scalar_struct(log, btf, member_type, rec + 1))
+				return false;
+			continue;
+		}
+		if (btf_type_is_array(member_type)) {
+			array = btf_type_array(member_type);
+			if (!array->nelems)
+				return false;
+			member_type = btf_type_skip_modifiers(btf, array->type, NULL);
+			if (!btf_type_is_scalar(member_type))
+				return false;
+			continue;
+		}
+		if (!btf_type_is_scalar(member_type))
+			return false;
+	}
+	return true;
+}
+
 static int btf_check_func_arg_match(struct bpf_verifier_env *env,
 				    const struct btf *btf, u32 func_id,
 				    struct bpf_reg_state *regs,
 				    bool ptr_to_mem_ok)
 {
+	enum bpf_prog_type prog_type = env->prog->type == BPF_PROG_TYPE_EXT ?
+		env->prog->aux->dst_prog->type : env->prog->type;
 	struct bpf_verifier_log *log = &env->log;
+	bool is_kfunc = btf_is_kernel(btf);
 	const char *func_name, *ref_tname;
 	const struct btf_type *t, *ref_t;
 	const struct btf_param *args;
@@ -5493,7 +5548,20 @@
 
 		ref_t = btf_type_skip_modifiers(btf, t->type, &ref_id);
 		ref_tname = btf_name_by_offset(btf, ref_t->name_off);
-		if (btf_is_kernel(btf)) {
+		if (btf_get_prog_ctx_type(log, btf, t, prog_type, i)) {
+			/* If function expects ctx type in BTF check that caller
+			 * is passing PTR_TO_CTX.
+			 */
+			if (reg->type != PTR_TO_CTX) {
+				bpf_log(log,
+					"arg#%d expected pointer to ctx, but got %s\n",
+					i, btf_type_str(t));
+				return -EINVAL;
+			}
+			if (check_ptr_off_reg(env, reg, regno))
+				return -EINVAL;
+		} else if (is_kfunc && (reg->type == PTR_TO_BTF_ID ||
+			   (reg2btf_ids[base_type(reg->type)] && !type_flag(reg->type)))) {
 			const struct btf_type *reg_ref_t;
 			const struct btf *reg_btf;
 			const char *reg_ref_tname;
@@ -5509,14 +5577,9 @@
 			if (reg->type == PTR_TO_BTF_ID) {
 				reg_btf = reg->btf;
 				reg_ref_id = reg->btf_id;
-			} else if (reg2btf_ids[reg->type]) {
-				reg_btf = btf_vmlinux;
-				reg_ref_id = *reg2btf_ids[reg->type];
 			} else {
-				bpf_log(log, "kernel function %s args#%d expected pointer to %s %s but R%d is not a pointer to btf_id\n",
-					func_name, i,
-					btf_type_str(ref_t), ref_tname, regno);
-				return -EINVAL;
+				reg_btf = btf_vmlinux;
+				reg_ref_id = *reg2btf_ids[base_type(reg->type)];
 			}
 
 			reg_ref_t = btf_type_skip_modifiers(reg_btf, reg_ref_id,
@@ -5532,23 +5595,24 @@
 					reg_ref_tname);
 				return -EINVAL;
 			}
-		} else if (btf_get_prog_ctx_type(log, btf, t,
-						 env->prog->type, i)) {
-			/* If function expects ctx type in BTF check that caller
-			 * is passing PTR_TO_CTX.
-			 */
-			if (reg->type != PTR_TO_CTX) {
-				bpf_log(log,
-					"arg#%d expected pointer to ctx, but got %s\n",
-					i, btf_type_str(t));
-				return -EINVAL;
-			}
-			if (check_ctx_reg(env, reg, regno))
-				return -EINVAL;
 		} else if (ptr_to_mem_ok) {
 			const struct btf_type *resolve_ret;
 			u32 type_size;
 
+			if (is_kfunc) {
+				/* Permit pointer to mem, but only when argument
+				 * type is pointer to scalar, or struct composed
+				 * (recursively) of scalars.
+				 */
+				if (!btf_type_is_scalar(ref_t) &&
+				    !__btf_type_is_scalar_struct(log, btf, ref_t, 0)) {
+					bpf_log(log,
+						"arg#%d pointer type %s %s must point to scalar or struct with scalar\n",
+						i, btf_type_str(ref_t), ref_tname);
+					return -EINVAL;
+				}
+			}
+
 			resolve_ret = btf_resolve_size(btf, ref_t, &type_size);
 			if (IS_ERR(resolve_ret)) {
 				bpf_log(log,
@@ -5561,6 +5625,8 @@
 			if (check_mem_reg(env, reg, regno, type_size))
 				return -EINVAL;
 		} else {
+			bpf_log(log, "reg type unsupported for arg#%d %sfunction %s#%d\n", i,
+				is_kfunc ? "kernel " : "", func_name, func_id);
 			return -EINVAL;
 		}
 	}
@@ -5610,7 +5676,7 @@
 			      const struct btf *btf, u32 func_id,
 			      struct bpf_reg_state *regs)
 {
-	return btf_check_func_arg_match(env, btf, func_id, regs, false);
+	return btf_check_func_arg_match(env, btf, func_id, regs, true);
 }
 
 /* Convert BTF of a function into bpf_reg_state if possible
@@ -5718,7 +5784,7 @@
 				return -EINVAL;
 			}
 
-			reg->type = PTR_TO_MEM_OR_NULL;
+			reg->type = PTR_TO_MEM | PTR_MAYBE_NULL;
 			reg->id = ++env->id_gen;
 
 			continue;
@@ -5742,8 +5808,8 @@
 	btf_type_ops(t)->show(btf, t, type_id, obj, 0, show);
 }
 
-static void btf_seq_show(struct btf_show *show, const char *fmt,
-			 va_list args)
+__printf(2, 0) static void btf_seq_show(struct btf_show *show, const char *fmt,
+					va_list args)
 {
 	seq_vprintf((struct seq_file *)show->target, fmt, args);
 }
@@ -5776,8 +5842,8 @@
 	int len;		/* length we would have written */
 };
 
-static void btf_snprintf_show(struct btf_show *show, const char *fmt,
-			      va_list args)
+__printf(2, 0) static void btf_snprintf_show(struct btf_show *show, const char *fmt,
+					     va_list args)
 {
 	struct btf_show_snprintf *ssnprintf = (struct btf_show_snprintf *)show;
 	int len;
@@ -6007,12 +6073,17 @@
 	return bsearch(&id, set->ids, set->cnt, sizeof(u32), btf_id_cmp_func) != NULL;
 }
 
+enum {
+	BTF_MODULE_F_LIVE = (1 << 0),
+};
+
 #ifdef CONFIG_DEBUG_INFO_BTF_MODULES
 struct btf_module {
 	struct list_head list;
 	struct module *module;
 	struct btf *btf;
 	struct bin_attribute *sysfs_attr;
+	int flags;
 };
 
 static LIST_HEAD(btf_modules);
@@ -6038,7 +6109,8 @@
 	int err = 0;
 
 	if (mod->btf_data_size == 0 ||
-	    (op != MODULE_STATE_COMING && op != MODULE_STATE_GOING))
+	    (op != MODULE_STATE_COMING && op != MODULE_STATE_LIVE &&
+	     op != MODULE_STATE_GOING))
 		goto out;
 
 	switch (op) {
@@ -6096,6 +6168,17 @@
 		}
 
 		break;
+	case MODULE_STATE_LIVE:
+		mutex_lock(&btf_module_mutex);
+		list_for_each_entry_safe(btf_mod, tmp, &btf_modules, list) {
+			if (btf_mod->module != module)
+				continue;
+
+			btf_mod->flags |= BTF_MODULE_F_LIVE;
+			break;
+		}
+		mutex_unlock(&btf_module_mutex);
+		break;
 	case MODULE_STATE_GOING:
 		mutex_lock(&btf_module_mutex);
 		list_for_each_entry_safe(btf_mod, tmp, &btf_modules, list) {
@@ -6141,7 +6224,12 @@
 		if (btf_mod->btf != btf)
 			continue;
 
-		if (try_module_get(btf_mod->module))
+		/* We must only consider module whose __init routine has
+		 * finished, hence we must check for BTF_MODULE_F_LIVE flag,
+		 * which is set from the notifier callback for
+		 * MODULE_STATE_LIVE.
+		 */
+		if ((btf_mod->flags & BTF_MODULE_F_LIVE) && try_module_get(btf_mod->module))
 			res = btf_mod->module;
 
 		break;
@@ -6208,7 +6296,7 @@
 	.func		= bpf_btf_find_by_name_kind,
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
-	.arg1_type	= ARG_PTR_TO_MEM,
+	.arg1_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg2_type	= ARG_CONST_SIZE,
 	.arg3_type	= ARG_ANYTHING,
 	.arg4_type	= ARG_ANYTHING,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/cgroup.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/cgroup.c
@@ -668,6 +668,62 @@
 }
 
 /**
+ * purge_effective_progs() - After compute_effective_progs fails to alloc new
+ *                           cgrp->bpf.inactive table we can recover by
+ *                           recomputing the array in place.
+ *
+ * @cgrp: The cgroup which descendants to travers
+ * @prog: A program to detach or NULL
+ * @link: A link to detach or NULL
+ * @atype: Type of detach operation
+ */
+static void purge_effective_progs(struct cgroup *cgrp, struct bpf_prog *prog,
+				  struct bpf_cgroup_link *link,
+				  enum cgroup_bpf_attach_type atype)
+{
+	struct cgroup_subsys_state *css;
+	struct bpf_prog_array *progs;
+	struct bpf_prog_list *pl;
+	struct list_head *head;
+	struct cgroup *cg;
+	int pos;
+
+	/* recompute effective prog array in place */
+	css_for_each_descendant_pre(css, &cgrp->self) {
+		struct cgroup *desc = container_of(css, struct cgroup, self);
+
+		if (percpu_ref_is_zero(&desc->bpf.refcnt))
+			continue;
+
+		/* find position of link or prog in effective progs array */
+		for (pos = 0, cg = desc; cg; cg = cgroup_parent(cg)) {
+			if (pos && !(cg->bpf.flags[atype] & BPF_F_ALLOW_MULTI))
+				continue;
+
+			head = &cg->bpf.progs[atype];
+			list_for_each_entry(pl, head, node) {
+				if (!prog_list_prog(pl))
+					continue;
+				if (pl->prog == prog && pl->link == link)
+					goto found;
+				pos++;
+			}
+		}
+
+		/* no link or prog match, skip the cgroup of this layer */
+		continue;
+found:
+		progs = rcu_dereference_protected(
+				desc->bpf.effective[atype],
+				lockdep_is_held(&cgroup_mutex));
+
+		/* Remove the program from the array */
+		WARN_ONCE(bpf_prog_array_delete_safe_at(progs, pos),
+			  "Failed to purge a prog from array at index %d", pos);
+	}
+}
+
+/**
  * __cgroup_bpf_detach() - Detach the program or link from a cgroup, and
  *                         propagate the change to descendants
  * @cgrp: The cgroup which descendants to traverse
@@ -686,7 +742,6 @@
 	struct bpf_prog_list *pl;
 	struct list_head *progs;
 	u32 flags;
-	int err;
 
 	atype = to_cgroup_bpf_attach_type(type);
 	if (atype < 0)
@@ -708,9 +763,12 @@
 	pl->prog = NULL;
 	pl->link = NULL;
 
-	err = update_effective_progs(cgrp, atype);
-	if (err)
-		goto cleanup;
+	if (update_effective_progs(cgrp, atype)) {
+		/* if update effective array failed replace the prog with a dummy prog*/
+		pl->prog = old_prog;
+		pl->link = link;
+		purge_effective_progs(cgrp, old_prog, link, atype);
+	}
 
 	/* now can actually delete it from this cgroup list */
 	list_del(&pl->node);
@@ -722,12 +780,6 @@
 		bpf_prog_put(old_prog);
 	static_branch_dec(&cgroup_bpf_enabled_key[atype]);
 	return 0;
-
-cleanup:
-	/* restore back prog or link */
-	pl->prog = old_prog;
-	pl->link = link;
-	return err;
 }
 
 /* Must be called with cgroup_mutex held to avoid races. */
@@ -1429,6 +1481,12 @@
 		ret = 1;
 	} else if (ctx.optlen > max_optlen || ctx.optlen < -1) {
 		/* optlen is out of bounds */
+		if (*optlen > PAGE_SIZE && ctx.optlen >= 0) {
+			pr_info_once("bpf setsockopt: ignoring program buffer with optlen=%d (max_optlen=%d)\n",
+				     ctx.optlen, max_optlen);
+			ret = 0;
+			goto out;
+		}
 		ret = -EFAULT;
 	} else {
 		/* optlen within bounds, run kernel handler */
@@ -1484,6 +1542,7 @@
 		.optname = optname,
 		.retval = retval,
 	};
+	int orig_optlen;
 	int ret;
 
 	/* Opportunistic check to see whether we have any BPF program
@@ -1493,6 +1552,7 @@
 	if (__cgroup_bpf_prog_array_is_empty(cgrp, CGROUP_GETSOCKOPT))
 		return retval;
 
+	orig_optlen = max_optlen;
 	ctx.optlen = max_optlen;
 
 	max_optlen = sockopt_alloc_buf(&ctx, max_optlen, &buf);
@@ -1516,6 +1576,7 @@
 			ret = -EFAULT;
 			goto out;
 		}
+		orig_optlen = ctx.optlen;
 
 		if (copy_from_user(ctx.optval, optval,
 				   min(ctx.optlen, max_optlen)) != 0) {
@@ -1534,7 +1595,13 @@
 		goto out;
 	}
 
-	if (ctx.optlen > max_optlen || ctx.optlen < 0) {
+	if (optval && (ctx.optlen > max_optlen || ctx.optlen < 0)) {
+		if (orig_optlen > PAGE_SIZE && ctx.optlen >= 0) {
+			pr_info_once("bpf getsockopt: ignoring program buffer with optlen=%d (max_optlen=%d)\n",
+				     ctx.optlen, max_optlen);
+			ret = retval;
+			goto out;
+		}
 		ret = -EFAULT;
 		goto out;
 	}
@@ -1548,8 +1615,11 @@
 	}
 
 	if (ctx.optlen != 0) {
-		if (copy_to_user(optval, ctx.optval, ctx.optlen) ||
-		    put_user(ctx.optlen, optlen)) {
+		if (optval && copy_to_user(optval, ctx.optval, ctx.optlen)) {
+			ret = -EFAULT;
+			goto out;
+		}
+		if (put_user(ctx.optlen, optlen)) {
 			ret = -EFAULT;
 			goto out;
 		}
@@ -1753,7 +1823,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 };
 
@@ -1773,6 +1843,8 @@
 		return &bpf_sysctl_get_new_value_proto;
 	case BPF_FUNC_sysctl_set_new_value:
 		return &bpf_sysctl_set_new_value_proto;
+	case BPF_FUNC_ktime_get_coarse_ns:
+		return &bpf_ktime_get_coarse_ns_proto;
 	default:
 		return cgroup_base_func_proto(func_id, prog);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/core.c
@@ -32,6 +32,7 @@
 #include <linux/perf_event.h>
 #include <linux/extable.h>
 #include <linux/log2.h>
+#include <linux/nospec.h>
 
 #include <asm/barrier.h>
 #include <asm/unaligned.h>
@@ -66,11 +67,13 @@
 {
 	u8 *ptr = NULL;
 
-	if (k >= SKF_NET_OFF)
+	if (k >= SKF_NET_OFF) {
 		ptr = skb_network_header(skb) + k - SKF_NET_OFF;
-	else if (k >= SKF_LL_OFF)
+	} else if (k >= SKF_LL_OFF) {
+		if (unlikely(!skb_mac_header_was_set(skb)))
+			return NULL;
 		ptr = skb_mac_header(skb) + k - SKF_LL_OFF;
-
+	}
 	if (ptr >= skb->head && ptr + size <= skb_tail_pointer(skb))
 		return ptr;
 
@@ -389,6 +392,13 @@
 			i = end_new;
 			insn = prog->insnsi + end_old;
 		}
+		if (bpf_pseudo_func(insn)) {
+			ret = bpf_adj_delta_to_imm(insn, pos, end_old,
+						   end_new, i, probe_pass);
+			if (ret)
+				return ret;
+			continue;
+		}
 		code = insn->code;
 		if ((BPF_CLASS(code) != BPF_JMP &&
 		     BPF_CLASS(code) != BPF_JMP32) ||
@@ -494,6 +504,8 @@
 
 int bpf_remove_insns(struct bpf_prog *prog, u32 off, u32 cnt)
 {
+	int err;
+
 	/* Branch offsets can't overflow when program is shrinking, no need
 	 * to call bpf_adj_branches(..., true) here
 	 */
@@ -501,7 +513,9 @@
 		sizeof(struct bpf_insn) * (prog->len - off - cnt));
 	prog->len -= cnt;
 
-	return WARN_ON_ONCE(bpf_adj_branches(prog, off, off + cnt, off, false));
+	err = bpf_adj_branches(prog, off, off + cnt, off, false);
+	WARN_ON_ONCE(err);
+	return err;
 }
 
 static void bpf_prog_kallsyms_del_subprogs(struct bpf_prog *fp)
@@ -595,7 +609,11 @@
 
 	if (val < ksym->start)
 		return -1;
-	if (val >= ksym->end)
+	/* Ensure that we detect return addresses as part of the program, when
+	 * the final instruction is a call for a program part of the stack
+	 * trace. Therefore, do val > ksym->end instead of val >= ksym->end.
+	 */
+	if (val > ksym->end)
 		return  1;
 
 	return 0;
@@ -819,7 +837,7 @@
 {
 	/* Only used as heuristic here to derive limit. */
 	bpf_jit_limit_max = bpf_jit_alloc_exec_limit();
-	bpf_jit_limit = min_t(u64, round_up(bpf_jit_limit_max >> 2,
+	bpf_jit_limit = min_t(u64, round_up(bpf_jit_limit_max >> 1,
 					    PAGE_SIZE), LONG_MAX);
 	return 0;
 }
@@ -1639,9 +1657,7 @@
 		 * reuse preexisting logic from Spectre v1 mitigation that
 		 * happens to produce the required code on x86 for v4 as well.
 		 */
-#ifdef CONFIG_X86
 		barrier_nospec();
-#endif
 		CONT;
 #define LDST(SIZEOP, SIZE)						\
 	STX_MEM_##SIZEOP:						\
@@ -1652,6 +1668,11 @@
 		CONT;							\
 	LDX_MEM_##SIZEOP:						\
 		DST = *(SIZE *)(unsigned long) (SRC + insn->off);	\
+		CONT;							\
+	LDX_PROBE_MEM_##SIZEOP:						\
+		bpf_probe_read_kernel(&DST, sizeof(SIZE),		\
+				      (const void *)(long) (SRC + insn->off));	\
+		DST = *((SIZE *)&DST);					\
 		CONT;
 
 	LDST(B,   u8)
@@ -1659,15 +1680,6 @@
 	LDST(W,  u32)
 	LDST(DW, u64)
 #undef LDST
-#define LDX_PROBE(SIZEOP, SIZE)							\
-	LDX_PROBE_MEM_##SIZEOP:							\
-		bpf_probe_read_kernel(&DST, SIZE, (const void *)(long) (SRC + insn->off));	\
-		CONT;
-	LDX_PROBE(B,  1)
-	LDX_PROBE(H,  2)
-	LDX_PROBE(W,  4)
-	LDX_PROBE(DW, 8)
-#undef LDX_PROBE
 
 #define ATOMIC_ALU_OP(BOP, KOP)						\
 		case BOP:						\
@@ -1932,7 +1944,9 @@
 	}
 
 finalize:
-	bpf_prog_lock_ro(fp);
+	*err = bpf_prog_lock_ro(fp);
+	if (*err)
+		return fp;
 
 	/* The tail call compatibility check can only be done at
 	 * this late stage as we need to determine, if we deal
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/cpumap.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/cpumap.c
@@ -26,6 +26,7 @@
 #include <linux/workqueue.h>
 #include <linux/kthread.h>
 #include <linux/capability.h>
+#include <linux/completion.h>
 #include <trace/events/xdp.h>
 
 #include <linux/netdevice.h>   /* netif_receive_skb_list */
@@ -70,6 +71,7 @@
 	struct rcu_head rcu;
 
 	struct work_struct kthread_stop_wq;
+	struct completion kthread_running;
 };
 
 struct bpf_cpu_map {
@@ -126,22 +128,6 @@
 	atomic_inc(&rcpu->refcnt);
 }
 
-/* called from workqueue, to workaround syscall using preempt_disable */
-static void cpu_map_kthread_stop(struct work_struct *work)
-{
-	struct bpf_cpu_map_entry *rcpu;
-
-	rcpu = container_of(work, struct bpf_cpu_map_entry, kthread_stop_wq);
-
-	/* Wait for flush in __cpu_map_entry_free(), via full RCU barrier,
-	 * as it waits until all in-flight call_rcu() callbacks complete.
-	 */
-	rcu_barrier();
-
-	/* kthread_stop will wake_up_process and wait for it to complete */
-	kthread_stop(rcpu->kthread);
-}
-
 static void __cpu_map_ring_cleanup(struct ptr_ring *ring)
 {
 	/* The tear-down procedure should have made sure that queue is
@@ -149,11 +135,17 @@
 	 * invoked cpu_map_kthread_stop(). Catch any broken behaviour
 	 * gracefully and warn once.
 	 */
-	struct xdp_frame *xdpf;
+	void *ptr;
 
-	while ((xdpf = ptr_ring_consume(ring)))
-		if (WARN_ON_ONCE(xdpf))
-			xdp_return_frame(xdpf);
+	while ((ptr = ptr_ring_consume(ring))) {
+		WARN_ON_ONCE(1);
+		if (unlikely(__ptr_test_bit(0, &ptr))) {
+			__ptr_clear_bit(0, &ptr);
+			kfree_skb(ptr);
+			continue;
+		}
+		xdp_return_frame(ptr);
+	}
 }
 
 static void put_cpu_map_entry(struct bpf_cpu_map_entry *rcpu)
@@ -169,6 +161,22 @@
 	}
 }
 
+/* called from workqueue, to workaround syscall using preempt_disable */
+static void cpu_map_kthread_stop(struct work_struct *work)
+{
+	struct bpf_cpu_map_entry *rcpu;
+
+	rcpu = container_of(work, struct bpf_cpu_map_entry, kthread_stop_wq);
+
+	/* Wait for flush in __cpu_map_entry_free(), via full RCU barrier,
+	 * as it waits until all in-flight call_rcu() callbacks complete.
+	 */
+	rcu_barrier();
+
+	/* kthread_stop will wake_up_process and wait for it to complete */
+	kthread_stop(rcpu->kthread);
+}
+
 static void cpu_map_bpf_prog_run_skb(struct bpf_cpu_map_entry *rcpu,
 				     struct list_head *listp,
 				     struct xdp_cpumap_stats *stats)
@@ -213,7 +221,7 @@
 				    void **frames, int n,
 				    struct xdp_cpumap_stats *stats)
 {
-	struct xdp_rxq_info rxq;
+	struct xdp_rxq_info rxq = {};
 	struct xdp_buff xdp;
 	int i, nframes = 0;
 
@@ -294,11 +302,12 @@
 	return nframes;
 }
 
-
 static int cpu_map_kthread_run(void *data)
 {
 	struct bpf_cpu_map_entry *rcpu = data;
+	unsigned long last_qs = jiffies;
 
+	complete(&rcpu->kthread_running);
 	set_current_state(TASK_INTERRUPTIBLE);
 
 	/* When kthread gives stop order, then rcpu have been disconnected
@@ -322,10 +331,12 @@
 			if (__ptr_ring_empty(rcpu->queue)) {
 				schedule();
 				sched = 1;
+				last_qs = jiffies;
 			} else {
 				__set_current_state(TASK_RUNNING);
 			}
 		} else {
+			rcu_softirq_qs_periodic(last_qs);
 			sched = cond_resched();
 		}
 
@@ -461,6 +472,7 @@
 		goto free_ptr_ring;
 
 	/* Setup kthread */
+	init_completion(&rcpu->kthread_running);
 	rcpu->kthread = kthread_create_on_node(cpu_map_kthread_run, rcpu, numa,
 					       "cpumap/%d/map:%d", cpu,
 					       map->id);
@@ -474,6 +486,12 @@
 	kthread_bind(rcpu->kthread, cpu);
 	wake_up_process(rcpu->kthread);
 
+	/* Make sure kthread has been running, so kthread_stop() will not
+	 * stop the kthread prematurely and all pending frames or skbs
+	 * will be handled by the kthread before kthread_stop() returns.
+	 */
+	wait_for_completion(&rcpu->kthread_running);
+
 	return rcpu;
 
 free_prog:
@@ -746,15 +764,9 @@
 		list_add(&bq->flush_node, flush_list);
 }
 
-int cpu_map_enqueue(struct bpf_cpu_map_entry *rcpu, struct xdp_buff *xdp,
+int cpu_map_enqueue(struct bpf_cpu_map_entry *rcpu, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx)
 {
-	struct xdp_frame *xdpf;
-
-	xdpf = xdp_convert_buff_to_frame(xdp);
-	if (unlikely(!xdpf))
-		return -EOVERFLOW;
-
 	/* Info needed when constructing SKB on remote CPU */
 	xdpf->dev_rx = dev_rx;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/devmap.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/devmap.c
@@ -130,13 +130,14 @@
 	bpf_map_init_from_attr(&dtab->map, attr);
 
 	if (attr->map_type == BPF_MAP_TYPE_DEVMAP_HASH) {
-		dtab->n_buckets = roundup_pow_of_two(dtab->map.max_entries);
-
-		if (!dtab->n_buckets) /* Overflow check */
+		/* hash table size must be power of 2; roundup_pow_of_two() can
+		 * overflow into UB on 32-bit arches, so check that first
+		 */
+		if (dtab->map.max_entries > 1UL << 31)
 			return -EINVAL;
-	}
 
-	if (attr->map_type == BPF_MAP_TYPE_DEVMAP_HASH) {
+		dtab->n_buckets = roundup_pow_of_two(dtab->map.max_entries);
+
 		dtab->dev_index_head = dev_map_create_hash(dtab->n_buckets,
 							   dtab->map.numa_node);
 		if (!dtab->dev_index_head)
@@ -182,7 +183,7 @@
 static void dev_map_free(struct bpf_map *map)
 {
 	struct bpf_dtab *dtab = container_of(map, struct bpf_dtab, map);
-	int i;
+	u32 i;
 
 	/* At this point bpf_prog->aux->refcnt == 0 and this map->refcnt == 0,
 	 * so the programs (can be more than one that used this map) were
@@ -324,9 +325,11 @@
 
 static int dev_map_bpf_prog_run(struct bpf_prog *xdp_prog,
 				struct xdp_frame **frames, int n,
-				struct net_device *dev)
+				struct net_device *tx_dev,
+				struct net_device *rx_dev)
 {
-	struct xdp_txq_info txq = { .dev = dev };
+	struct xdp_txq_info txq = { .dev = tx_dev };
+	struct xdp_rxq_info rxq = { .dev = rx_dev };
 	struct xdp_buff xdp;
 	int i, nframes = 0;
 
@@ -337,6 +340,7 @@
 
 		xdp_convert_frame_to_buff(xdpf, &xdp);
 		xdp.txq = &txq;
+		xdp.rxq = &rxq;
 
 		act = bpf_prog_run_xdp(xdp_prog, &xdp);
 		switch (act) {
@@ -351,7 +355,7 @@
 			bpf_warn_invalid_xdp_action(act);
 			fallthrough;
 		case XDP_ABORTED:
-			trace_xdp_exception(dev, xdp_prog, act);
+			trace_xdp_exception(tx_dev, xdp_prog, act);
 			fallthrough;
 		case XDP_DROP:
 			xdp_return_frame_rx_napi(xdpf);
@@ -379,7 +383,7 @@
 	}
 
 	if (bq->xdp_prog) {
-		to_send = dev_map_bpf_prog_run(bq->xdp_prog, bq->q, cnt, dev);
+		to_send = dev_map_bpf_prog_run(bq->xdp_prog, bq->q, cnt, dev, bq->dev_rx);
 		if (!to_send)
 			goto out;
 	}
@@ -467,24 +471,19 @@
 	bq->q[bq->count++] = xdpf;
 }
 
-static inline int __xdp_enqueue(struct net_device *dev, struct xdp_buff *xdp,
+static inline int __xdp_enqueue(struct net_device *dev, struct xdp_frame *xdpf,
 				struct net_device *dev_rx,
 				struct bpf_prog *xdp_prog)
 {
-	struct xdp_frame *xdpf;
 	int err;
 
 	if (!dev->netdev_ops->ndo_xdp_xmit)
 		return -EOPNOTSUPP;
 
-	err = xdp_ok_fwd_dev(dev, xdp->data_end - xdp->data);
+	err = xdp_ok_fwd_dev(dev, xdpf->len);
 	if (unlikely(err))
 		return err;
 
-	xdpf = xdp_convert_buff_to_frame(xdp);
-	if (unlikely(!xdpf))
-		return -EOVERFLOW;
-
 	bq_enqueue(dev, xdpf, dev_rx, xdp_prog);
 	return 0;
 }
@@ -520,27 +519,27 @@
 	return act;
 }
 
-int dev_xdp_enqueue(struct net_device *dev, struct xdp_buff *xdp,
+int dev_xdp_enqueue(struct net_device *dev, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx)
 {
-	return __xdp_enqueue(dev, xdp, dev_rx, NULL);
+	return __xdp_enqueue(dev, xdpf, dev_rx, NULL);
 }
 
-int dev_map_enqueue(struct bpf_dtab_netdev *dst, struct xdp_buff *xdp,
+int dev_map_enqueue(struct bpf_dtab_netdev *dst, struct xdp_frame *xdpf,
 		    struct net_device *dev_rx)
 {
 	struct net_device *dev = dst->dev;
 
-	return __xdp_enqueue(dev, xdp, dev_rx, dst->xdp_prog);
+	return __xdp_enqueue(dev, xdpf, dev_rx, dst->xdp_prog);
 }
 
-static bool is_valid_dst(struct bpf_dtab_netdev *obj, struct xdp_buff *xdp)
+static bool is_valid_dst(struct bpf_dtab_netdev *obj, struct xdp_frame *xdpf)
 {
 	if (!obj ||
 	    !obj->dev->netdev_ops->ndo_xdp_xmit)
 		return false;
 
-	if (xdp_ok_fwd_dev(obj->dev, xdp->data_end - xdp->data))
+	if (xdp_ok_fwd_dev(obj->dev, xdpf->len))
 		return false;
 
 	return true;
@@ -586,14 +585,13 @@
 	return n;
 }
 
-int dev_map_enqueue_multi(struct xdp_buff *xdp, struct net_device *dev_rx,
+int dev_map_enqueue_multi(struct xdp_frame *xdpf, struct net_device *dev_rx,
 			  struct bpf_map *map, bool exclude_ingress)
 {
 	struct bpf_dtab *dtab = container_of(map, struct bpf_dtab, map);
 	struct bpf_dtab_netdev *dst, *last_dst = NULL;
 	int excluded_devices[1+MAX_NEST_DEV];
 	struct hlist_head *head;
-	struct xdp_frame *xdpf;
 	int num_excluded = 0;
 	unsigned int i;
 	int err;
@@ -603,15 +601,11 @@
 		excluded_devices[num_excluded++] = dev_rx->ifindex;
 	}
 
-	xdpf = xdp_convert_buff_to_frame(xdp);
-	if (unlikely(!xdpf))
-		return -EOVERFLOW;
-
 	if (map->map_type == BPF_MAP_TYPE_DEVMAP) {
 		for (i = 0; i < map->max_entries; i++) {
 			dst = rcu_dereference_check(dtab->netdev_map[i],
 						    rcu_read_lock_bh_held());
-			if (!is_valid_dst(dst, xdp))
+			if (!is_valid_dst(dst, xdpf))
 				continue;
 
 			if (is_ifindex_excluded(excluded_devices, num_excluded, dst->dev->ifindex))
@@ -634,7 +628,7 @@
 			head = dev_map_index_hash(dtab, i);
 			hlist_for_each_entry_rcu(dst, head, index_hlist,
 						 lockdep_is_held(&dtab->index_lock)) {
-				if (!is_valid_dst(dst, xdp))
+				if (!is_valid_dst(dst, xdpf))
 					continue;
 
 				if (is_ifindex_excluded(excluded_devices, num_excluded,
@@ -812,7 +806,7 @@
 {
 	struct bpf_dtab *dtab = container_of(map, struct bpf_dtab, map);
 	struct bpf_dtab_netdev *old_dev;
-	int k = *(u32 *)key;
+	u32 k = *(u32 *)key;
 
 	if (k >= map->max_entries)
 		return -EINVAL;
@@ -827,7 +821,7 @@
 {
 	struct bpf_dtab *dtab = container_of(map, struct bpf_dtab, map);
 	struct bpf_dtab_netdev *old_dev;
-	int k = *(u32 *)key;
+	u32 k = *(u32 *)key;
 	unsigned long flags;
 	int ret = -ENOENT;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/hashtab.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/hashtab.c
@@ -161,17 +161,25 @@
 				   unsigned long *pflags)
 {
 	unsigned long flags;
+	bool use_raw_lock;
 
-	hash = hash & HASHTAB_MAP_LOCK_MASK;
+	hash = hash & min_t(u32, HASHTAB_MAP_LOCK_MASK, htab->n_buckets - 1);
 
-	migrate_disable();
+	use_raw_lock = htab_use_raw_lock(htab);
+	if (use_raw_lock)
+		preempt_disable();
+	else
+		migrate_disable();
 	if (unlikely(__this_cpu_inc_return(*(htab->map_locked[hash])) != 1)) {
 		__this_cpu_dec(*(htab->map_locked[hash]));
-		migrate_enable();
+		if (use_raw_lock)
+			preempt_enable();
+		else
+			migrate_enable();
 		return -EBUSY;
 	}
 
-	if (htab_use_raw_lock(htab))
+	if (use_raw_lock)
 		raw_spin_lock_irqsave(&b->raw_lock, flags);
 	else
 		spin_lock_irqsave(&b->lock, flags);
@@ -184,13 +192,18 @@
 				      struct bucket *b, u32 hash,
 				      unsigned long flags)
 {
-	hash = hash & HASHTAB_MAP_LOCK_MASK;
-	if (htab_use_raw_lock(htab))
+	bool use_raw_lock = htab_use_raw_lock(htab);
+
+	hash = hash & min_t(u32, HASHTAB_MAP_LOCK_MASK, htab->n_buckets - 1);
+	if (use_raw_lock)
 		raw_spin_unlock_irqrestore(&b->raw_lock, flags);
 	else
 		spin_unlock_irqrestore(&b->lock, flags);
 	__this_cpu_dec(*(htab->map_locked[hash]));
-	migrate_enable();
+	if (use_raw_lock)
+		preempt_enable();
+	else
+		migrate_enable();
 }
 
 static bool htab_lru_map_delete_node(void *arg, struct bpf_lru_node *node);
@@ -291,12 +304,8 @@
 	struct htab_elem *l;
 
 	if (node) {
-		u32 key_size = htab->map.key_size;
-
 		l = container_of(node, struct htab_elem, lru_node);
-		memcpy(l->key, key, key_size);
-		check_and_init_map_value(&htab->map,
-					 l->key + round_up(key_size, 8));
+		memcpy(l->key, key, htab->map.key_size);
 		return l;
 	}
 
@@ -455,6 +464,9 @@
 		 * kmalloc-able later in htab_map_update_elem()
 		 */
 		return -E2BIG;
+	/* percpu map value size is bound by PCPU_MIN_UNIT_SIZE */
+	if (percpu && round_up(attr->value_size, 8) > PCPU_MIN_UNIT_SIZE)
+		return -E2BIG;
 
 	return 0;
 }
@@ -495,7 +507,13 @@
 							  num_possible_cpus());
 	}
 
-	/* hash table size must be power of 2 */
+	/* hash table size must be power of 2; roundup_pow_of_two() can overflow
+	 * into UB on 32-bit arches, so check that first
+	 */
+	err = -E2BIG;
+	if (htab->map.max_entries > 1UL << 31)
+		goto free_htab;
+
 	htab->n_buckets = roundup_pow_of_two(htab->map.max_entries);
 
 	htab->elem_size = sizeof(struct htab_elem) +
@@ -505,10 +523,8 @@
 	else
 		htab->elem_size += round_up(htab->map.value_size, 8);
 
-	err = -E2BIG;
-	/* prevent zero size kmalloc and check for u32 overflow */
-	if (htab->n_buckets == 0 ||
-	    htab->n_buckets > U32_MAX / sizeof(struct bucket))
+	/* check for u32 overflow */
+	if (htab->n_buckets > U32_MAX / sizeof(struct bucket))
 		goto free_htab;
 
 	err = -ENOMEM;
@@ -848,7 +864,7 @@
 
 	if (map->ops->map_fd_put_ptr) {
 		ptr = fd_htab_map_get_ptr(map, l);
-		map->ops->map_fd_put_ptr(ptr);
+		map->ops->map_fd_put_ptr(map, ptr, true);
 	}
 }
 
@@ -1156,7 +1172,7 @@
 
 	ret = htab_lock_bucket(htab, b, hash, &flags);
 	if (ret)
-		return ret;
+		goto err_lock_bucket;
 
 	l_old = lookup_elem_raw(head, hash, key, key_size);
 
@@ -1177,6 +1193,7 @@
 err:
 	htab_unlock_bucket(htab, b, hash, flags);
 
+err_lock_bucket:
 	if (ret)
 		htab_lru_push_free(htab, l_new);
 	else if (l_old)
@@ -1279,7 +1296,7 @@
 
 	ret = htab_lock_bucket(htab, b, hash, &flags);
 	if (ret)
-		return ret;
+		goto err_lock_bucket;
 
 	l_old = lookup_elem_raw(head, hash, key, key_size);
 
@@ -1302,6 +1319,7 @@
 	ret = 0;
 err:
 	htab_unlock_bucket(htab, b, hash, flags);
+err_lock_bucket:
 	if (l_new)
 		bpf_lru_push_free(&htab->lru, &l_new->lru_node);
 	return ret;
@@ -1662,8 +1680,11 @@
 	/* do not grab the lock unless need it (bucket_cnt > 0). */
 	if (locked) {
 		ret = htab_lock_bucket(htab, b, batch, &flags);
-		if (ret)
-			goto next_batch;
+		if (ret) {
+			rcu_read_unlock();
+			bpf_enable_instrumentation();
+			goto after_loop;
+		}
 	}
 
 	bucket_cnt = 0;
@@ -2023,6 +2044,7 @@
 		seq_info->percpu_value_buf = value_buf;
 	}
 
+	bpf_map_inc_with_uref(map);
 	seq_info->map = map;
 	seq_info->htab = container_of(map, struct bpf_htab, map);
 	return 0;
@@ -2032,6 +2054,7 @@
 {
 	struct bpf_iter_seq_hash_map_info *seq_info = priv_data;
 
+	bpf_map_put_with_uref(seq_info->map);
 	kfree(seq_info->percpu_value_buf);
 }
 
@@ -2314,7 +2337,7 @@
 		hlist_nulls_for_each_entry_safe(l, n, head, hash_node) {
 			void *ptr = fd_htab_map_get_ptr(map, l);
 
-			map->ops->map_fd_put_ptr(ptr);
+			map->ops->map_fd_put_ptr(map, ptr, false);
 		}
 	}
 
@@ -2355,7 +2378,7 @@
 
 	ret = htab_map_update_elem(map, key, &ptr, map_flags);
 	if (ret)
-		map->ops->map_fd_put_ptr(ptr);
+		map->ops->map_fd_put_ptr(map, ptr, false);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/helpers.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/helpers.c
@@ -15,6 +15,7 @@
 #include <linux/pid_namespace.h>
 #include <linux/proc_ns.h>
 #include <linux/security.h>
+#include <linux/rcupdate_trace.h>
 
 #include "../../lib/kstrtox.h"
 
@@ -24,12 +25,13 @@
  *
  * Different map implementations will rely on rcu in map methods
  * lookup/update/delete, therefore eBPF programs must run under rcu lock
- * if program is allowed to access maps, so check rcu_read_lock_held in
- * all three functions.
+ * if program is allowed to access maps, so check rcu_read_lock_held() or
+ * rcu_read_lock_trace_held() in all three functions.
  */
 BPF_CALL_2(bpf_map_lookup_elem, struct bpf_map *, map, void *, key)
 {
-	WARN_ON_ONCE(!rcu_read_lock_held() && !rcu_read_lock_bh_held());
+	WARN_ON_ONCE(!rcu_read_lock_held() && !rcu_read_lock_trace_held() &&
+		     !rcu_read_lock_bh_held());
 	return (unsigned long) map->ops->map_lookup_elem(map, key);
 }
 
@@ -45,7 +47,8 @@
 BPF_CALL_4(bpf_map_update_elem, struct bpf_map *, map, void *, key,
 	   void *, value, u64, flags)
 {
-	WARN_ON_ONCE(!rcu_read_lock_held() && !rcu_read_lock_bh_held());
+	WARN_ON_ONCE(!rcu_read_lock_held() && !rcu_read_lock_trace_held() &&
+		     !rcu_read_lock_bh_held());
 	return map->ops->map_update_elem(map, key, value, flags);
 }
 
@@ -62,7 +65,8 @@
 
 BPF_CALL_2(bpf_map_delete_elem, struct bpf_map *, map, void *, key)
 {
-	WARN_ON_ONCE(!rcu_read_lock_held() && !rcu_read_lock_bh_held());
+	WARN_ON_ONCE(!rcu_read_lock_held() && !rcu_read_lock_trace_held() &&
+		     !rcu_read_lock_bh_held());
 	return map->ops->map_delete_elem(map, key);
 }
 
@@ -298,7 +302,7 @@
 	__this_cpu_write(irqsave_flags, flags);
 }
 
-notrace BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
+NOTRACE_BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
 {
 	__bpf_spin_lock_irqsave(lock);
 	return 0;
@@ -320,7 +324,7 @@
 	local_irq_restore(flags);
 }
 
-notrace BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
+NOTRACE_BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
 {
 	__bpf_spin_unlock_irqrestore(lock);
 	return 0;
@@ -512,7 +516,7 @@
 }
 
 BPF_CALL_4(bpf_strtol, const char *, buf, size_t, buf_len, u64, flags,
-	   long *, res)
+	   s64 *, res)
 {
 	long long _res;
 	int err;
@@ -530,14 +534,14 @@
 	.func		= bpf_strtol,
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
-	.arg1_type	= ARG_PTR_TO_MEM,
+	.arg1_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg2_type	= ARG_CONST_SIZE,
 	.arg3_type	= ARG_ANYTHING,
 	.arg4_type	= ARG_PTR_TO_LONG,
 };
 
 BPF_CALL_4(bpf_strtoul, const char *, buf, size_t, buf_len, u64, flags,
-	   unsigned long *, res)
+	   u64 *, res)
 {
 	unsigned long long _res;
 	bool is_negative;
@@ -558,7 +562,7 @@
 	.func		= bpf_strtoul,
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
-	.arg1_type	= ARG_PTR_TO_MEM,
+	.arg1_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg2_type	= ARG_CONST_SIZE,
 	.arg3_type	= ARG_ANYTHING,
 	.arg4_type	= ARG_PTR_TO_LONG,
@@ -630,7 +634,7 @@
 	.arg1_type      = ARG_PTR_TO_CTX,
 	.arg2_type      = ARG_CONST_MAP_PTR,
 	.arg3_type      = ARG_ANYTHING,
-	.arg4_type      = ARG_PTR_TO_MEM,
+	.arg4_type      = ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type      = ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -667,7 +671,7 @@
 const struct bpf_func_proto bpf_per_cpu_ptr_proto = {
 	.func		= bpf_per_cpu_ptr,
 	.gpl_only	= false,
-	.ret_type	= RET_PTR_TO_MEM_OR_BTF_ID_OR_NULL,
+	.ret_type	= RET_PTR_TO_MEM_OR_BTF_ID | PTR_MAYBE_NULL | MEM_RDONLY,
 	.arg1_type	= ARG_PTR_TO_PERCPU_BTF_ID,
 	.arg2_type	= ARG_ANYTHING,
 };
@@ -680,7 +684,7 @@
 const struct bpf_func_proto bpf_this_cpu_ptr_proto = {
 	.func		= bpf_this_cpu_ptr,
 	.gpl_only	= false,
-	.ret_type	= RET_PTR_TO_MEM_OR_BTF_ID,
+	.ret_type	= RET_PTR_TO_MEM_OR_BTF_ID | MEM_RDONLY,
 	.arg1_type	= ARG_PTR_TO_PERCPU_BTF_ID,
 };
 
@@ -710,19 +714,20 @@
 /* Per-cpu temp buffers used by printf-like helpers to store the bprintf binary
  * arguments representation.
  */
-#define MAX_BPRINTF_BUF_LEN	512
+#define MAX_BPRINTF_BIN_ARGS	512
 
 /* Support executing three nested bprintf helper calls on a given CPU */
 #define MAX_BPRINTF_NEST_LEVEL	3
 struct bpf_bprintf_buffers {
-	char tmp_bufs[MAX_BPRINTF_NEST_LEVEL][MAX_BPRINTF_BUF_LEN];
+	char bin_args[MAX_BPRINTF_BIN_ARGS];
+	char buf[MAX_BPRINTF_BUF];
 };
-static DEFINE_PER_CPU(struct bpf_bprintf_buffers, bpf_bprintf_bufs);
+
+static DEFINE_PER_CPU(struct bpf_bprintf_buffers[MAX_BPRINTF_NEST_LEVEL], bpf_bprintf_bufs);
 static DEFINE_PER_CPU(int, bpf_bprintf_nest_level);
 
-static int try_get_fmt_tmp_buf(char **tmp_buf)
+static int try_get_buffers(struct bpf_bprintf_buffers **bufs)
 {
-	struct bpf_bprintf_buffers *bufs;
 	int nest_level;
 
 	preempt_disable();
@@ -732,18 +737,19 @@
 		preempt_enable();
 		return -EBUSY;
 	}
-	bufs = this_cpu_ptr(&bpf_bprintf_bufs);
-	*tmp_buf = bufs->tmp_bufs[nest_level - 1];
+	*bufs = this_cpu_ptr(&bpf_bprintf_bufs[nest_level - 1]);
 
 	return 0;
 }
 
-void bpf_bprintf_cleanup(void)
+void bpf_bprintf_cleanup(struct bpf_bprintf_data *data)
 {
-	if (this_cpu_read(bpf_bprintf_nest_level)) {
-		this_cpu_dec(bpf_bprintf_nest_level);
-		preempt_enable();
-	}
+	if (!data->bin_args && !data->buf)
+		return;
+	if (WARN_ON_ONCE(this_cpu_read(bpf_bprintf_nest_level) == 0))
+		return;
+	this_cpu_dec(bpf_bprintf_nest_level);
+	preempt_enable();
 }
 
 /*
@@ -752,18 +758,20 @@
  * Returns a negative value if fmt is an invalid format string or 0 otherwise.
  *
  * This can be used in two ways:
- * - Format string verification only: when bin_args is NULL
+ * - Format string verification only: when data->get_bin_args is false
  * - Arguments preparation: in addition to the above verification, it writes in
- *   bin_args a binary representation of arguments usable by bstr_printf where
- *   pointers from BPF have been sanitized.
+ *   data->bin_args a binary representation of arguments usable by bstr_printf
+ *   where pointers from BPF have been sanitized.
  *
  * In argument preparation mode, if 0 is returned, safe temporary buffers are
  * allocated and bpf_bprintf_cleanup should be called to free them after use.
  */
 int bpf_bprintf_prepare(char *fmt, u32 fmt_size, const u64 *raw_args,
-			u32 **bin_args, u32 num_args)
+			u32 num_args, struct bpf_bprintf_data *data)
 {
+	bool get_buffers = (data->get_bin_args && num_args) || data->get_buf;
 	char *unsafe_ptr = NULL, *tmp_buf = NULL, *tmp_buf_end, *fmt_end;
+	struct bpf_bprintf_buffers *buffers = NULL;
 	size_t sizeof_cur_arg, sizeof_cur_ip;
 	int err, i, num_spec = 0;
 	u64 cur_arg;
@@ -774,14 +782,19 @@
 		return -EINVAL;
 	fmt_size = fmt_end - fmt;
 
-	if (bin_args) {
-		if (num_args && try_get_fmt_tmp_buf(&tmp_buf))
-			return -EBUSY;
+	if (get_buffers && try_get_buffers(&buffers))
+		return -EBUSY;
 
-		tmp_buf_end = tmp_buf + MAX_BPRINTF_BUF_LEN;
-		*bin_args = (u32 *)tmp_buf;
+	if (data->get_bin_args) {
+		if (num_args)
+			tmp_buf = buffers->bin_args;
+		tmp_buf_end = tmp_buf + MAX_BPRINTF_BIN_ARGS;
+		data->bin_args = (u32 *)tmp_buf;
 	}
 
+	if (data->get_buf)
+		data->buf = buffers->buf;
+
 	for (i = 0; i < fmt_size; i++) {
 		if ((!isprint(fmt[i]) && !isspace(fmt[i])) || !isascii(fmt[i])) {
 			err = -EINVAL;
@@ -975,33 +988,33 @@
 	err = 0;
 out:
 	if (err)
-		bpf_bprintf_cleanup();
+		bpf_bprintf_cleanup(data);
 	return err;
 }
 
-#define MAX_SNPRINTF_VARARGS		12
-
 BPF_CALL_5(bpf_snprintf, char *, str, u32, str_size, char *, fmt,
-	   const void *, data, u32, data_len)
+	   const void *, args, u32, data_len)
 {
+	struct bpf_bprintf_data data = {
+		.get_bin_args	= true,
+	};
 	int err, num_args;
-	u32 *bin_args;
 
-	if (data_len % 8 || data_len > MAX_SNPRINTF_VARARGS * 8 ||
-	    (data_len && !data))
+	if (data_len % 8 || data_len > MAX_BPRINTF_VARARGS * 8 ||
+	    (data_len && !args))
 		return -EINVAL;
 	num_args = data_len / 8;
 
 	/* ARG_PTR_TO_CONST_STR guarantees that fmt is zero-terminated so we
 	 * can safely give an unbounded size.
 	 */
-	err = bpf_bprintf_prepare(fmt, UINT_MAX, data, &bin_args, num_args);
+	err = bpf_bprintf_prepare(fmt, UINT_MAX, args, num_args, &data);
 	if (err < 0)
 		return err;
 
-	err = bstr_printf(str, str_size, fmt, bin_args);
+	err = bstr_printf(str, str_size, fmt, data.bin_args);
 
-	bpf_bprintf_cleanup();
+	bpf_bprintf_cleanup(&data);
 
 	return err + 1;
 }
@@ -1013,7 +1026,7 @@
 	.arg1_type	= ARG_PTR_TO_MEM_OR_NULL,
 	.arg2_type	= ARG_CONST_SIZE_OR_ZERO,
 	.arg3_type	= ARG_PTR_TO_CONST_STR,
-	.arg4_type	= ARG_PTR_TO_MEM_OR_NULL,
+	.arg4_type	= ARG_PTR_TO_MEM | PTR_MAYBE_NULL | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -1039,6 +1052,7 @@
 	struct bpf_prog *prog;
 	void __rcu *callback_fn;
 	void *value;
+	struct rcu_head rcu;
 };
 
 /* the actual struct hidden inside uapi struct bpf_timer */
@@ -1118,13 +1132,6 @@
 		ret = -EBUSY;
 		goto out;
 	}
-	if (!atomic64_read(&map->usercnt)) {
-		/* maps with timers must be either held by user space
-		 * or pinned in bpffs.
-		 */
-		ret = -EPERM;
-		goto out;
-	}
 	/* allocate hrtimer via map_kmalloc to use memcg accounting */
 	t = bpf_map_kmalloc_node(map, sizeof(*t), GFP_ATOMIC, map->numa_node);
 	if (!t) {
@@ -1137,7 +1144,21 @@
 	rcu_assign_pointer(t->callback_fn, NULL);
 	hrtimer_init(&t->timer, clockid, HRTIMER_MODE_REL_SOFT);
 	t->timer.function = bpf_timer_cb;
-	timer->timer = t;
+	WRITE_ONCE(timer->timer, t);
+	/* Guarantee the order between timer->timer and map->usercnt. So
+	 * when there are concurrent uref release and bpf timer init, either
+	 * bpf_timer_cancel_and_free() called by uref release reads a no-NULL
+	 * timer or atomic64_read() below returns a zero usercnt.
+	 */
+	smp_mb();
+	if (!atomic64_read(&map->usercnt)) {
+		/* maps with timers must be either held by user space
+		 * or pinned in bpffs.
+		 */
+		WRITE_ONCE(timer->timer, NULL);
+		kfree(t);
+		ret = -EPERM;
+	}
 out:
 	__bpf_spin_unlock_irqrestore(&timer->lock);
 	return ret;
@@ -1253,6 +1274,7 @@
 
 	if (in_nmi())
 		return -EOPNOTSUPP;
+	rcu_read_lock();
 	__bpf_spin_lock_irqsave(&timer->lock);
 	t = timer->timer;
 	if (!t) {
@@ -1274,6 +1296,7 @@
 	 * if it was running.
 	 */
 	ret = ret ?: hrtimer_cancel(&t->timer);
+	rcu_read_unlock();
 	return ret;
 }
 
@@ -1305,7 +1328,7 @@
 	/* The subsequent bpf_timer_start/cancel() helpers won't be able to use
 	 * this timer, since it won't be initialized.
 	 */
-	timer->timer = NULL;
+	WRITE_ONCE(timer->timer, NULL);
 out:
 	__bpf_spin_unlock_irqrestore(&timer->lock);
 	if (!t)
@@ -1328,7 +1351,7 @@
 	 */
 	if (this_cpu_read(hrtimer_running) != t)
 		hrtimer_cancel(&t->timer);
-	kfree(t);
+	kfree_rcu(t, rcu);
 }
 
 const struct bpf_func_proto bpf_get_current_task_proto __weak;
@@ -1367,8 +1390,6 @@
 		return &bpf_ktime_get_ns_proto;
 	case BPF_FUNC_ktime_get_boot_ns:
 		return &bpf_ktime_get_boot_ns_proto;
-	case BPF_FUNC_ktime_get_coarse_ns:
-		return &bpf_ktime_get_coarse_ns_proto;
 	case BPF_FUNC_ringbuf_output:
 		return &bpf_ringbuf_output_proto;
 	case BPF_FUNC_ringbuf_reserve:
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/inode.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/inode.c
@@ -648,12 +648,22 @@
 	int opt;
 
 	opt = fs_parse(fc, bpf_fs_parameters, param, &result);
-	if (opt < 0)
+	if (opt < 0) {
 		/* We might like to report bad mount options here, but
 		 * traditionally we've ignored all mount options, so we'd
 		 * better continue to ignore non-existing options for bpf.
 		 */
-		return opt == -ENOPARAM ? 0 : opt;
+		if (opt == -ENOPARAM) {
+			opt = vfs_parse_fs_param_source(fc, param);
+			if (opt != -ENOPARAM)
+				return opt;
+
+			return 0;
+		}
+
+		if (opt < 0)
+			return opt;
+	}
 
 	switch (opt) {
 	case OPT_MODE:
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/lpm_trie.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/lpm_trie.c
@@ -230,6 +230,9 @@
 	struct lpm_trie_node *node, *found = NULL;
 	struct bpf_lpm_trie_key *key = _key;
 
+	if (key->prefixlen > trie->max_prefixlen)
+		return NULL;
+
 	/* Start walking the trie from the root node ... */
 
 	for (node = rcu_dereference_check(trie->root, rcu_read_lock_bh_held());
@@ -363,6 +366,10 @@
 	 * simply assign the @new_node to that slot and be done.
 	 */
 	if (!node) {
+		if (flags == BPF_EXIST) {
+			ret = -ENOENT;
+			goto out;
+		}
 		rcu_assign_pointer(*slot, new_node);
 		goto out;
 	}
@@ -371,18 +378,31 @@
 	 * which already has the correct data array set.
 	 */
 	if (node->prefixlen == matchlen) {
+		if (!(node->flags & LPM_TREE_NODE_FLAG_IM)) {
+			if (flags == BPF_NOEXIST) {
+				ret = -EEXIST;
+				goto out;
+			}
+			trie->n_entries--;
+		} else if (flags == BPF_EXIST) {
+			ret = -ENOENT;
+			goto out;
+		}
+
 		new_node->child[0] = node->child[0];
 		new_node->child[1] = node->child[1];
 
-		if (!(node->flags & LPM_TREE_NODE_FLAG_IM))
-			trie->n_entries--;
-
 		rcu_assign_pointer(*slot, new_node);
 		kfree_rcu(node, rcu);
 
 		goto out;
 	}
 
+	if (flags == BPF_EXIST) {
+		ret = -ENOENT;
+		goto out;
+	}
+
 	/* If the new node matches the prefix completely, it must be inserted
 	 * as an ancestor. Simply insert it between @node and *@slot.
 	 */
@@ -619,7 +639,7 @@
 	struct lpm_trie_node **node_stack = NULL;
 	int err = 0, stack_ptr = -1;
 	unsigned int next_bit;
-	size_t matchlen;
+	size_t matchlen = 0;
 
 	/* The get_next_key follows postorder. For the 4 node example in
 	 * the top of this file, the trie_get_next_key() returns the following
@@ -641,7 +661,7 @@
 	if (!key || key->prefixlen > trie->max_prefixlen)
 		goto find_leftmost;
 
-	node_stack = kmalloc_array(trie->max_prefixlen,
+	node_stack = kmalloc_array(trie->max_prefixlen + 1,
 				   sizeof(struct lpm_trie_node *),
 				   GFP_ATOMIC | __GFP_NOWARN);
 	if (!node_stack)
@@ -658,7 +678,7 @@
 		next_bit = extract_bit(key->data, node->prefixlen);
 		node = rcu_dereference(node->child[next_bit]);
 	}
-	if (!node || node->prefixlen != key->prefixlen ||
+	if (!node || node->prefixlen != matchlen ||
 	    (node->flags & LPM_TREE_NODE_FLAG_IM))
 		goto find_leftmost;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/map_in_map.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/map_in_map.c
@@ -108,12 +108,17 @@
 	return inner_map;
 }
 
-void bpf_map_fd_put_ptr(void *ptr)
+void bpf_map_fd_put_ptr(struct bpf_map *map, void *ptr, bool need_defer)
 {
-	/* ptr->ops->map_free() has to go through one
-	 * rcu grace period by itself.
+	struct bpf_map *inner_map = ptr;
+
+	/* The inner map may still be used by both non-sleepable and sleepable
+	 * bpf program, so free it after one RCU grace period and one tasks
+	 * trace RCU grace period.
 	 */
-	bpf_map_put(ptr);
+	if (need_defer)
+		WRITE_ONCE(inner_map->free_after_mult_rcu_gp, true);
+	bpf_map_put(inner_map);
 }
 
 u32 bpf_map_fd_sys_lookup_elem(void *ptr)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/map_in_map.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/map_in_map.h
@@ -13,7 +13,7 @@
 void bpf_map_meta_free(struct bpf_map *map_meta);
 void *bpf_map_fd_get_ptr(struct bpf_map *map, struct file *map_file,
 			 int ufd);
-void bpf_map_fd_put_ptr(void *ptr);
+void bpf_map_fd_put_ptr(struct bpf_map *map, void *ptr, bool need_defer);
 u32 bpf_map_fd_sys_lookup_elem(void *ptr);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/map_iter.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/map_iter.c
@@ -174,9 +174,9 @@
 	.ctx_arg_info_size	= 2,
 	.ctx_arg_info		= {
 		{ offsetof(struct bpf_iter__bpf_map_elem, key),
-		  PTR_TO_RDONLY_BUF_OR_NULL },
+		  PTR_TO_BUF | PTR_MAYBE_NULL | MEM_RDONLY },
 		{ offsetof(struct bpf_iter__bpf_map_elem, value),
-		  PTR_TO_RDWR_BUF_OR_NULL },
+		  PTR_TO_BUF | PTR_MAYBE_NULL },
 	},
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/offload.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/offload.c
@@ -216,9 +216,6 @@
 	if (offload->dev_state)
 		offload->offdev->ops->destroy(prog);
 
-	/* Make sure BPF_PROG_GET_NEXT_ID can't find this dead program */
-	bpf_prog_free_id(prog, true);
-
 	list_del_init(&offload->offloads);
 	kfree(offload);
 	prog->aux->offload = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/percpu_freelist.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/percpu_freelist.c
@@ -102,22 +102,21 @@
 			    u32 nr_elems)
 {
 	struct pcpu_freelist_head *head;
-	int i, cpu, pcpu_entries;
+	unsigned int cpu, cpu_idx, i, j, n, m;
 
-	pcpu_entries = nr_elems / num_possible_cpus() + 1;
-	i = 0;
+	n = nr_elems / num_possible_cpus();
+	m = nr_elems % num_possible_cpus();
 
+	cpu_idx = 0;
 	for_each_possible_cpu(cpu) {
-again:
 		head = per_cpu_ptr(s->freelist, cpu);
-		/* No locking required as this is not visible yet. */
-		pcpu_freelist_push_node(head, buf);
-		i++;
-		buf += elem_size;
-		if (i == nr_elems)
-			break;
-		if (i % pcpu_entries)
-			goto again;
+		j = n + (cpu_idx < m ? 1 : 0);
+		for (i = 0; i < j; i++) {
+			/* No locking required as this is not visible yet. */
+			pcpu_freelist_push_node(head, buf);
+			buf += elem_size;
+		}
+		cpu_idx++;
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/queue_stack_maps.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/queue_stack_maps.c
@@ -103,7 +103,12 @@
 	int err = 0;
 	void *ptr;
 
-	raw_spin_lock_irqsave(&qs->lock, flags);
+	if (in_nmi()) {
+		if (!raw_spin_trylock_irqsave(&qs->lock, flags))
+			return -EBUSY;
+	} else {
+		raw_spin_lock_irqsave(&qs->lock, flags);
+	}
 
 	if (queue_stack_map_is_empty(qs)) {
 		memset(value, 0, qs->map.value_size);
@@ -133,7 +138,12 @@
 	void *ptr;
 	u32 index;
 
-	raw_spin_lock_irqsave(&qs->lock, flags);
+	if (in_nmi()) {
+		if (!raw_spin_trylock_irqsave(&qs->lock, flags))
+			return -EBUSY;
+	} else {
+		raw_spin_lock_irqsave(&qs->lock, flags);
+	}
 
 	if (queue_stack_map_is_empty(qs)) {
 		memset(value, 0, qs->map.value_size);
@@ -198,7 +208,12 @@
 	if (flags & BPF_NOEXIST || flags > BPF_EXIST)
 		return -EINVAL;
 
-	raw_spin_lock_irqsave(&qs->lock, irq_flags);
+	if (in_nmi()) {
+		if (!raw_spin_trylock_irqsave(&qs->lock, irq_flags))
+			return -EBUSY;
+	} else {
+		raw_spin_lock_irqsave(&qs->lock, irq_flags);
+	}
 
 	if (queue_stack_map_is_full(qs)) {
 		if (!replace) {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/ringbuf.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/ringbuf.c
@@ -41,9 +41,12 @@
 	 * mapping consumer page as r/w, but restrict producer page to r/o.
 	 * This protects producer position from being modified by user-space
 	 * application and ruining in-kernel position tracking.
+	 * Note that the pending counter is placed in the same
+	 * page as the producer, so that it shares the same cache line.
 	 */
 	unsigned long consumer_pos __aligned(PAGE_SIZE);
 	unsigned long producer_pos __aligned(PAGE_SIZE);
+	unsigned long pending_pos;
 	char data[] __aligned(PAGE_SIZE);
 };
 
@@ -104,7 +107,7 @@
 	}
 
 	rb = vmap(pages, nr_meta_pages + 2 * nr_data_pages,
-		  VM_ALLOC | VM_USERMAP, PAGE_KERNEL);
+		  VM_MAP | VM_USERMAP, PAGE_KERNEL);
 	if (rb) {
 		kmemleak_not_leak(pages);
 		rb->pages = pages;
@@ -141,6 +144,7 @@
 	rb->mask = data_sz - 1;
 	rb->consumer_pos = 0;
 	rb->producer_pos = 0;
+	rb->pending_pos = 0;
 
 	return rb;
 }
@@ -304,9 +308,9 @@
 
 static void *__bpf_ringbuf_reserve(struct bpf_ringbuf *rb, u64 size)
 {
-	unsigned long cons_pos, prod_pos, new_prod_pos, flags;
-	u32 len, pg_off;
+	unsigned long cons_pos, prod_pos, new_prod_pos, pend_pos, flags;
 	struct bpf_ringbuf_hdr *hdr;
+	u32 len, pg_off, tmp_size, hdr_len;
 
 	if (unlikely(size > RINGBUF_MAX_RECORD_SZ))
 		return NULL;
@@ -324,13 +328,29 @@
 		spin_lock_irqsave(&rb->spinlock, flags);
 	}
 
+	pend_pos = rb->pending_pos;
 	prod_pos = rb->producer_pos;
 	new_prod_pos = prod_pos + len;
 
-	/* check for out of ringbuf space by ensuring producer position
-	 * doesn't advance more than (ringbuf_size - 1) ahead
+	while (pend_pos < prod_pos) {
+		hdr = (void *)rb->data + (pend_pos & rb->mask);
+		hdr_len = READ_ONCE(hdr->len);
+		if (hdr_len & BPF_RINGBUF_BUSY_BIT)
+			break;
+		tmp_size = hdr_len & ~BPF_RINGBUF_DISCARD_BIT;
+		tmp_size = round_up(tmp_size + BPF_RINGBUF_HDR_SZ, 8);
+		pend_pos += tmp_size;
+	}
+	rb->pending_pos = pend_pos;
+
+	/* check for out of ringbuf space:
+	 * - by ensuring producer position doesn't advance more than
+	 *   (ringbuf_size - 1) ahead
+	 * - by ensuring oldest not yet committed record until newest
+	 *   record does not span more than (ringbuf_size - 1)
 	 */
-	if (new_prod_pos - cons_pos > rb->mask) {
+	if (new_prod_pos - cons_pos > rb->mask ||
+	    new_prod_pos - pend_pos > rb->mask) {
 		spin_unlock_irqrestore(&rb->spinlock, flags);
 		return NULL;
 	}
@@ -444,7 +464,7 @@
 	.func		= bpf_ringbuf_output,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_CONST_MAP_PTR,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE_OR_ZERO,
 	.arg4_type	= ARG_ANYTHING,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/stackmap.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/stackmap.c
@@ -113,13 +113,15 @@
 	} else if (value_size / 8 > sysctl_perf_event_max_stack)
 		return ERR_PTR(-EINVAL);
 
-	/* hash table size must be power of 2 */
-	n_buckets = roundup_pow_of_two(attr->max_entries);
-	if (!n_buckets)
+	/* hash table size must be power of 2; roundup_pow_of_two() can overflow
+	 * into UB on 32-bit arches, so check that first
+	 */
+	if (attr->max_entries > 1UL << 31)
 		return ERR_PTR(-E2BIG);
 
+	n_buckets = roundup_pow_of_two(attr->max_entries);
+
 	cost = n_buckets * sizeof(struct stack_map_bucket *) + sizeof(*smap);
-	cost += n_buckets * (value_size + sizeof(struct stack_map_bucket));
 	smap = bpf_map_area_alloc(cost, bpf_map_attr_numa_node(attr));
 	if (!smap)
 		return ERR_PTR(-ENOMEM);
@@ -219,7 +221,7 @@
 }
 
 static struct perf_callchain_entry *
-get_callchain_entry_for_task(struct task_struct *task, u32 init_nr)
+get_callchain_entry_for_task(struct task_struct *task, u32 max_depth)
 {
 #ifdef CONFIG_STACKTRACE
 	struct perf_callchain_entry *entry;
@@ -230,9 +232,8 @@
 	if (!entry)
 		return NULL;
 
-	entry->nr = init_nr +
-		stack_trace_save_tsk(task, (unsigned long *)(entry->ip + init_nr),
-				     sysctl_perf_event_max_stack - init_nr, 0);
+	entry->nr = stack_trace_save_tsk(task, (unsigned long *)entry->ip,
+					 max_depth, 0);
 
 	/* stack_trace_save_tsk() works on unsigned long array, while
 	 * perf_callchain_entry uses u64 array. For 32-bit systems, it is
@@ -244,7 +245,7 @@
 		int i;
 
 		/* copy data from the end to avoid using extra buffer */
-		for (i = entry->nr - 1; i >= (int)init_nr; i--)
+		for (i = entry->nr - 1; i >= 0; i--)
 			to[i] = (u64)(from[i]);
 	}
 
@@ -261,27 +262,19 @@
 {
 	struct bpf_stack_map *smap = container_of(map, struct bpf_stack_map, map);
 	struct stack_map_bucket *bucket, *new_bucket, *old_bucket;
-	u32 max_depth = map->value_size / stack_map_data_size(map);
-	/* stack_map_alloc() checks that max_depth <= sysctl_perf_event_max_stack */
-	u32 init_nr = sysctl_perf_event_max_stack - max_depth;
 	u32 skip = flags & BPF_F_SKIP_FIELD_MASK;
 	u32 hash, id, trace_nr, trace_len;
 	bool user = flags & BPF_F_USER_STACK;
 	u64 *ips;
 	bool hash_matches;
 
-	/* get_perf_callchain() guarantees that trace->nr >= init_nr
-	 * and trace-nr <= sysctl_perf_event_max_stack, so trace_nr <= max_depth
-	 */
-	trace_nr = trace->nr - init_nr;
-
-	if (trace_nr <= skip)
+	if (trace->nr <= skip)
 		/* skipping more than usable stack trace */
 		return -EFAULT;
 
-	trace_nr -= skip;
+	trace_nr = trace->nr - skip;
 	trace_len = trace_nr * sizeof(u64);
-	ips = trace->ip + skip + init_nr;
+	ips = trace->ip + skip;
 	hash = jhash2((u32 *)ips, trace_len / sizeof(u32), 0);
 	id = hash & (smap->n_buckets - 1);
 	bucket = READ_ONCE(smap->buckets[id]);
@@ -338,8 +331,7 @@
 	   u64, flags)
 {
 	u32 max_depth = map->value_size / stack_map_data_size(map);
-	/* stack_map_alloc() checks that max_depth <= sysctl_perf_event_max_stack */
-	u32 init_nr = sysctl_perf_event_max_stack - max_depth;
+	u32 skip = flags & BPF_F_SKIP_FIELD_MASK;
 	bool user = flags & BPF_F_USER_STACK;
 	struct perf_callchain_entry *trace;
 	bool kernel = !user;
@@ -348,8 +340,12 @@
 			       BPF_F_FAST_STACK_CMP | BPF_F_REUSE_STACKID)))
 		return -EINVAL;
 
-	trace = get_perf_callchain(regs, init_nr, kernel, user,
-				   sysctl_perf_event_max_stack, false, false);
+	max_depth += skip;
+	if (max_depth > sysctl_perf_event_max_stack)
+		max_depth = sysctl_perf_event_max_stack;
+
+	trace = get_perf_callchain(regs, 0, kernel, user, max_depth,
+				   false, false);
 
 	if (unlikely(!trace))
 		/* couldn't fetch the stack trace */
@@ -440,8 +436,9 @@
 			    struct perf_callchain_entry *trace_in,
 			    void *buf, u32 size, u64 flags)
 {
-	u32 init_nr, trace_nr, copy_len, elem_size, num_elem;
+	u32 trace_nr, copy_len, elem_size, num_elem, max_depth;
 	bool user_build_id = flags & BPF_F_USER_BUILD_ID;
+	bool crosstask = task && task != current;
 	u32 skip = flags & BPF_F_SKIP_FIELD_MASK;
 	bool user = flags & BPF_F_USER_STACK;
 	struct perf_callchain_entry *trace;
@@ -464,31 +461,37 @@
 	if (task && user && !user_mode(regs))
 		goto err_fault;
 
+	/* get_perf_callchain does not support crosstask user stack walking
+	 * but returns an empty stack instead of NULL.
+	 */
+	if (crosstask && user) {
+		err = -EOPNOTSUPP;
+		goto clear;
+	}
+
 	num_elem = size / elem_size;
-	if (sysctl_perf_event_max_stack < num_elem)
-		init_nr = 0;
-	else
-		init_nr = sysctl_perf_event_max_stack - num_elem;
+	max_depth = num_elem + skip;
+	if (sysctl_perf_event_max_stack < max_depth)
+		max_depth = sysctl_perf_event_max_stack;
 
 	if (trace_in)
 		trace = trace_in;
 	else if (kernel && task)
-		trace = get_callchain_entry_for_task(task, init_nr);
+		trace = get_callchain_entry_for_task(task, max_depth);
 	else
-		trace = get_perf_callchain(regs, init_nr, kernel, user,
-					   sysctl_perf_event_max_stack,
-					   false, false);
+		trace = get_perf_callchain(regs, 0, kernel, user, max_depth,
+					   crosstask, false);
 	if (unlikely(!trace))
 		goto err_fault;
 
-	trace_nr = trace->nr - init_nr;
-	if (trace_nr < skip)
+	if (trace->nr < skip)
 		goto err_fault;
 
-	trace_nr -= skip;
+	trace_nr = trace->nr - skip;
 	trace_nr = (trace_nr <= num_elem) ? trace_nr : num_elem;
 	copy_len = trace_nr * elem_size;
-	ips = trace->ip + skip + init_nr;
+
+	ips = trace->ip + skip;
 	if (user && user_build_id)
 		stack_map_get_build_id_offset(buf, ips, trace_nr, user);
 	else
@@ -525,13 +528,14 @@
 	   u32, size, u64, flags)
 {
 	struct pt_regs *regs;
-	long res;
+	long res = -EINVAL;
 
 	if (!try_get_task_stack(task))
 		return -EFAULT;
 
 	regs = task_pt_regs(task);
-	res = __bpf_get_stack(regs, task, NULL, buf, size, flags);
+	if (regs)
+		res = __bpf_get_stack(regs, task, NULL, buf, size, flags);
 	put_task_stack(task);
 
 	return res;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/syscall.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/syscall.c
@@ -132,6 +132,21 @@
 	return map;
 }
 
+static void bpf_map_write_active_inc(struct bpf_map *map)
+{
+	atomic64_inc(&map->writecnt);
+}
+
+static void bpf_map_write_active_dec(struct bpf_map *map)
+{
+	atomic64_dec(&map->writecnt);
+}
+
+bool bpf_map_write_active(const struct bpf_map *map)
+{
+	return atomic64_read(&map->writecnt) != 0;
+}
+
 static u32 bpf_map_value_size(const struct bpf_map *map)
 {
 	if (map->map_type == BPF_MAP_TYPE_PERCPU_HASH ||
@@ -472,6 +487,25 @@
 	}
 }
 
+static void bpf_map_free_in_work(struct bpf_map *map)
+{
+	INIT_WORK(&map->work, bpf_map_free_deferred);
+	schedule_work(&map->work);
+}
+
+static void bpf_map_free_rcu_gp(struct rcu_head *rcu)
+{
+	bpf_map_free_in_work(container_of(rcu, struct bpf_map, rcu));
+}
+
+static void bpf_map_free_mult_rcu_gp(struct rcu_head *rcu)
+{
+	if (rcu_trace_implies_rcu_gp())
+		bpf_map_free_rcu_gp(rcu);
+	else
+		call_rcu(rcu, bpf_map_free_rcu_gp);
+}
+
 /* decrement map refcnt and schedule it for freeing via workqueue
  * (unrelying map implementation ops->map_free() might sleep)
  */
@@ -481,8 +515,11 @@
 		/* bpf_map_free_id() must be called first */
 		bpf_map_free_id(map, do_idr_lock);
 		btf_put(map->btf);
-		INIT_WORK(&map->work, bpf_map_free_deferred);
-		schedule_work(&map->work);
+
+		if (READ_ONCE(map->free_after_mult_rcu_gp))
+			call_rcu_tasks_trace(&map->rcu, bpf_map_free_mult_rcu_gp);
+		else
+			bpf_map_free_in_work(map);
 	}
 }
 
@@ -596,11 +633,8 @@
 {
 	struct bpf_map *map = vma->vm_file->private_data;
 
-	if (vma->vm_flags & VM_MAYWRITE) {
-		mutex_lock(&map->freeze_mutex);
-		map->writecnt++;
-		mutex_unlock(&map->freeze_mutex);
-	}
+	if (vma->vm_flags & VM_MAYWRITE)
+		bpf_map_write_active_inc(map);
 }
 
 /* called for all unmapped memory region (including initial) */
@@ -608,11 +642,8 @@
 {
 	struct bpf_map *map = vma->vm_file->private_data;
 
-	if (vma->vm_flags & VM_MAYWRITE) {
-		mutex_lock(&map->freeze_mutex);
-		map->writecnt--;
-		mutex_unlock(&map->freeze_mutex);
-	}
+	if (vma->vm_flags & VM_MAYWRITE)
+		bpf_map_write_active_dec(map);
 }
 
 static const struct vm_operations_struct bpf_map_default_vmops = {
@@ -663,7 +694,7 @@
 		goto out;
 
 	if (vma->vm_flags & VM_MAYWRITE)
-		map->writecnt++;
+		bpf_map_write_active_inc(map);
 out:
 	mutex_unlock(&map->freeze_mutex);
 	return err;
@@ -1122,6 +1153,7 @@
 	map = __bpf_map_get(f);
 	if (IS_ERR(map))
 		return PTR_ERR(map);
+	bpf_map_write_active_inc(map);
 	if (!(map_get_sys_perms(map, f) & FMODE_CAN_WRITE)) {
 		err = -EPERM;
 		goto err_put;
@@ -1157,6 +1189,7 @@
 free_key:
 	kvfree(key);
 err_put:
+	bpf_map_write_active_dec(map);
 	fdput(f);
 	return err;
 }
@@ -1179,6 +1212,7 @@
 	map = __bpf_map_get(f);
 	if (IS_ERR(map))
 		return PTR_ERR(map);
+	bpf_map_write_active_inc(map);
 	if (!(map_get_sys_perms(map, f) & FMODE_CAN_WRITE)) {
 		err = -EPERM;
 		goto err_put;
@@ -1209,6 +1243,7 @@
 out:
 	kvfree(key);
 err_put:
+	bpf_map_write_active_dec(map);
 	fdput(f);
 	return err;
 }
@@ -1301,6 +1336,9 @@
 	if (!max_count)
 		return 0;
 
+	if (put_user(0, &uattr->batch.count))
+		return -EFAULT;
+
 	key = kvmalloc(map->key_size, GFP_USER | __GFP_NOWARN);
 	if (!key)
 		return -ENOMEM;
@@ -1324,6 +1362,7 @@
 		maybe_wait_bpf_programs(map);
 		if (err)
 			break;
+		cond_resched();
 	}
 	if (copy_to_user(&uattr->batch.count, &cp, sizeof(cp)))
 		err = -EFAULT;
@@ -1358,6 +1397,9 @@
 	if (!max_count)
 		return 0;
 
+	if (put_user(0, &uattr->batch.count))
+		return -EFAULT;
+
 	key = kvmalloc(map->key_size, GFP_USER | __GFP_NOWARN);
 	if (!key)
 		return -ENOMEM;
@@ -1381,6 +1423,7 @@
 
 		if (err)
 			break;
+		cond_resched();
 	}
 
 	if (copy_to_user(&uattr->batch.count, &cp, sizeof(cp)))
@@ -1392,8 +1435,6 @@
 	return err;
 }
 
-#define MAP_LOOKUP_RETRIES 3
-
 int generic_map_lookup_batch(struct bpf_map *map,
 				    const union bpf_attr *attr,
 				    union bpf_attr __user *uattr)
@@ -1403,8 +1444,8 @@
 	void __user *values = u64_to_user_ptr(attr->batch.values);
 	void __user *keys = u64_to_user_ptr(attr->batch.keys);
 	void *buf, *buf_prevkey, *prev_key, *key, *value;
-	int err, retry = MAP_LOOKUP_RETRIES;
 	u32 value_size, cp, max_count;
+	int err;
 
 	if (attr->batch.elem_flags & ~BPF_F_LOCK)
 		return -EINVAL;
@@ -1450,14 +1491,8 @@
 		err = bpf_map_copy_value(map, key, value,
 					 attr->batch.elem_flags);
 
-		if (err == -ENOENT) {
-			if (retry) {
-				retry--;
-				continue;
-			}
-			err = -EINTR;
-			break;
-		}
+		if (err == -ENOENT)
+			goto next_key;
 
 		if (err)
 			goto free_buf;
@@ -1472,12 +1507,13 @@
 			goto free_buf;
 		}
 
+		cp++;
+next_key:
 		if (!prev_key)
 			prev_key = buf_prevkey;
 
 		swap(prev_key, key);
-		retry = MAP_LOOKUP_RETRIES;
-		cp++;
+		cond_resched();
 	}
 
 	if (err == -EFAULT)
@@ -1516,6 +1552,7 @@
 	map = __bpf_map_get(f);
 	if (IS_ERR(map))
 		return PTR_ERR(map);
+	bpf_map_write_active_inc(map);
 	if (!(map_get_sys_perms(map, f) & FMODE_CAN_READ) ||
 	    !(map_get_sys_perms(map, f) & FMODE_CAN_WRITE)) {
 		err = -EPERM;
@@ -1580,6 +1617,7 @@
 free_key:
 	kvfree(key);
 err_put:
+	bpf_map_write_active_dec(map);
 	fdput(f);
 	return err;
 }
@@ -1607,8 +1645,7 @@
 	}
 
 	mutex_lock(&map->freeze_mutex);
-
-	if (map->writecnt) {
+	if (bpf_map_write_active(map)) {
 		err = -EBUSY;
 		goto err_put;
 	}
@@ -1678,7 +1715,7 @@
 		return;
 	if (audit_enabled == AUDIT_OFF)
 		return;
-	if (op == BPF_AUDIT_LOAD)
+	if (!in_irq() && !irqs_disabled())
 		ctx = audit_context();
 	ab = audit_log_start(ctx, GFP_ATOMIC, AUDIT_BPF);
 	if (unlikely(!ab))
@@ -1773,6 +1810,7 @@
 	prog = aux->prog;
 	perf_event_bpf_event(prog, PERF_BPF_EVENT_PROG_UNLOAD, 0);
 	bpf_audit_prog(prog, BPF_AUDIT_UNLOAD);
+	bpf_prog_free_id(prog, true);
 	__bpf_prog_put_noref(prog, true);
 }
 
@@ -1781,9 +1819,6 @@
 	struct bpf_prog_aux *aux = prog->aux;
 
 	if (atomic64_dec_and_test(&aux->refcnt)) {
-		/* bpf_prog_free_id() must be called first */
-		bpf_prog_free_id(prog, do_idr_lock);
-
 		if (in_irq() || irqs_disabled()) {
 			INIT_WORK(&aux->work, bpf_prog_put_deferred);
 			schedule_work(&aux->work);
@@ -1807,8 +1842,14 @@
 	return 0;
 }
 
+struct bpf_prog_kstats {
+	u64 nsecs;
+	u64 cnt;
+	u64 misses;
+};
+
 static void bpf_prog_get_stats(const struct bpf_prog *prog,
-			       struct bpf_prog_stats *stats)
+			       struct bpf_prog_kstats *stats)
 {
 	u64 nsecs = 0, cnt = 0, misses = 0;
 	int cpu;
@@ -1821,9 +1862,9 @@
 		st = per_cpu_ptr(prog->stats, cpu);
 		do {
 			start = u64_stats_fetch_begin_irq(&st->syncp);
-			tnsecs = st->nsecs;
-			tcnt = st->cnt;
-			tmisses = st->misses;
+			tnsecs = u64_stats_read(&st->nsecs);
+			tcnt = u64_stats_read(&st->cnt);
+			tmisses = u64_stats_read(&st->misses);
 		} while (u64_stats_fetch_retry_irq(&st->syncp, start));
 		nsecs += tnsecs;
 		cnt += tcnt;
@@ -1839,7 +1880,7 @@
 {
 	const struct bpf_prog *prog = filp->private_data;
 	char prog_tag[sizeof(prog->tag) * 2 + 1] = { };
-	struct bpf_prog_stats stats;
+	struct bpf_prog_kstats stats;
 
 	bpf_prog_get_stats(prog, &stats);
 	bin2hex(prog_tag, prog->tag, sizeof(prog->tag));
@@ -2473,16 +2514,21 @@
 {
 	const struct bpf_link *link = filp->private_data;
 	const struct bpf_prog *prog = link->prog;
+	enum bpf_link_type type = link->type;
 	char prog_tag[sizeof(prog->tag) * 2 + 1] = { };
 
+	if (type < ARRAY_SIZE(bpf_link_type_strs) && bpf_link_type_strs[type]) {
+		seq_printf(m, "link_type:\t%s\n", bpf_link_type_strs[type]);
+	} else {
+		WARN_ONCE(1, "missing BPF_LINK_TYPE(...) for link type %u\n", type);
+		seq_printf(m, "link_type:\t<%u>\n", type);
+	}
+	seq_printf(m, "link_id:\t%u\n", link->id);
+
 	bin2hex(prog_tag, prog->tag, sizeof(prog->tag));
 	seq_printf(m,
-		   "link_type:\t%s\n"
-		   "link_id:\t%u\n"
 		   "prog_tag:\t%s\n"
 		   "prog_id:\t%u\n",
-		   bpf_link_type_strs[link->type],
-		   link->id,
 		   prog_tag,
 		   prog->aux->id);
 	if (link->ops->show_fdinfo)
@@ -2740,6 +2786,10 @@
 	 *
 	 * - if prog->aux->dst_trampoline and tgt_prog is NULL, the program
 	 *   was detached and is going for re-attachment.
+	 *
+	 * - if prog->aux->dst_trampoline is NULL and tgt_prog and prog->aux->attach_btf
+	 *   are NULL, then program was already attached and user did not provide
+	 *   tgt_prog_fd so we have no way to find out or create trampoline
 	 */
 	if (!prog->aux->dst_trampoline && !tgt_prog) {
 		/*
@@ -2753,6 +2803,11 @@
 			err = -EINVAL;
 			goto out_unlock;
 		}
+		/* We can allow re-attach only if we have valid attach_btf. */
+		if (!prog->aux->attach_btf) {
+			err = -EINVAL;
+			goto out_unlock;
+		}
 		btf_id = prog->aux->attach_btf_id;
 		key = bpf_trampoline_compute_key(NULL, prog->aux->attach_btf, btf_id);
 	}
@@ -3578,7 +3633,7 @@
 	struct bpf_prog_info __user *uinfo = u64_to_user_ptr(attr->info.info);
 	struct bpf_prog_info info;
 	u32 info_len = attr->info.info_len;
-	struct bpf_prog_stats stats;
+	struct bpf_prog_kstats stats;
 	char __user *uinsns;
 	u32 ulen;
 	int err;
@@ -4077,7 +4132,9 @@
 	if (attr->task_fd_query.flags != 0)
 		return -EINVAL;
 
+	rcu_read_lock();
 	task = get_pid_task(find_vpid(pid), PIDTYPE_PID);
+	rcu_read_unlock();
 	if (!task)
 		return -ENOENT;
 
@@ -4143,6 +4200,9 @@
 			    union bpf_attr __user *uattr,
 			    int cmd)
 {
+	bool has_read  = cmd == BPF_MAP_LOOKUP_BATCH ||
+			 cmd == BPF_MAP_LOOKUP_AND_DELETE_BATCH;
+	bool has_write = cmd != BPF_MAP_LOOKUP_BATCH;
 	struct bpf_map *map;
 	int err, ufd;
 	struct fd f;
@@ -4155,16 +4215,13 @@
 	map = __bpf_map_get(f);
 	if (IS_ERR(map))
 		return PTR_ERR(map);
-
-	if ((cmd == BPF_MAP_LOOKUP_BATCH ||
-	     cmd == BPF_MAP_LOOKUP_AND_DELETE_BATCH) &&
-	    !(map_get_sys_perms(map, f) & FMODE_CAN_READ)) {
+	if (has_write)
+		bpf_map_write_active_inc(map);
+	if (has_read && !(map_get_sys_perms(map, f) & FMODE_CAN_READ)) {
 		err = -EPERM;
 		goto err_put;
 	}
-
-	if (cmd != BPF_MAP_LOOKUP_BATCH &&
-	    !(map_get_sys_perms(map, f) & FMODE_CAN_WRITE)) {
+	if (has_write && !(map_get_sys_perms(map, f) & FMODE_CAN_WRITE)) {
 		err = -EPERM;
 		goto err_put;
 	}
@@ -4177,8 +4234,9 @@
 		BPF_DO_BATCH(map->ops->map_update_batch);
 	else
 		BPF_DO_BATCH(map->ops->map_delete_batch);
-
 err_put:
+	if (has_write)
+		bpf_map_write_active_dec(map);
 	fdput(f);
 	return err;
 }
@@ -4729,7 +4787,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_ANYTHING,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 };
 
@@ -4761,7 +4819,7 @@
 {
 	switch (func_id) {
 	case BPF_FUNC_sys_bpf:
-		return &bpf_sys_bpf_proto;
+		return !perfmon_capable() ? NULL : &bpf_sys_bpf_proto;
 	case BPF_FUNC_btf_find_by_name_kind:
 		return &bpf_btf_find_by_name_kind_proto;
 	case BPF_FUNC_sys_close:
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/trampoline.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/trampoline.c
@@ -108,18 +108,6 @@
 	tr->mod = NULL;
 }
 
-static int is_ftrace_location(void *ip)
-{
-	long addr;
-
-	addr = ftrace_location((long)ip);
-	if (!addr)
-		return 0;
-	if (WARN_ON_ONCE(addr != (long)ip))
-		return -EFAULT;
-	return 1;
-}
-
 static int unregister_fentry(struct bpf_trampoline *tr, void *old_addr)
 {
 	void *ip = tr->func.addr;
@@ -151,12 +139,12 @@
 static int register_fentry(struct bpf_trampoline *tr, void *new_addr)
 {
 	void *ip = tr->func.addr;
+	unsigned long faddr;
 	int ret;
 
-	ret = is_ftrace_location(ip);
-	if (ret < 0)
-		return ret;
-	tr->func.ftrace_managed = ret;
+	faddr = ftrace_location((unsigned long)ip);
+	if (faddr)
+		tr->func.ftrace_managed = true;
 
 	if (bpf_trampoline_module_get(tr))
 		return -ENOENT;
@@ -414,7 +402,7 @@
 {
 	enum bpf_tramp_prog_type kind;
 	int err = 0;
-	int cnt;
+	int cnt = 0, i;
 
 	kind = bpf_attach_type_to_tramp(prog);
 	mutex_lock(&tr->mutex);
@@ -425,7 +413,10 @@
 		err = -EBUSY;
 		goto out;
 	}
-	cnt = tr->progs_cnt[BPF_TRAMP_FENTRY] + tr->progs_cnt[BPF_TRAMP_FEXIT];
+
+	for (i = 0; i < BPF_TRAMP_MAX; i++)
+		cnt += tr->progs_cnt[i];
+
 	if (kind == BPF_TRAMP_REPLACE) {
 		/* Cannot attach extension if fentry/fexit are in use. */
 		if (cnt) {
@@ -503,16 +494,19 @@
 
 void bpf_trampoline_put(struct bpf_trampoline *tr)
 {
+	int i;
+
 	if (!tr)
 		return;
 	mutex_lock(&trampoline_mutex);
 	if (!refcount_dec_and_test(&tr->refcnt))
 		goto out;
 	WARN_ON_ONCE(mutex_is_locked(&tr->mutex));
-	if (WARN_ON_ONCE(!hlist_empty(&tr->progs_hlist[BPF_TRAMP_FENTRY])))
-		goto out;
-	if (WARN_ON_ONCE(!hlist_empty(&tr->progs_hlist[BPF_TRAMP_FEXIT])))
-		goto out;
+
+	for (i = 0; i < BPF_TRAMP_MAX; i++)
+		if (WARN_ON_ONCE(!hlist_empty(&tr->progs_hlist[i])))
+			goto out;
+
 	/* This code will be executed even when the last bpf_tramp_image
 	 * is alive. All progs are detached from the trampoline and the
 	 * trampoline image is patched with jmp into epilogue to skip
@@ -541,11 +535,12 @@
 static void notrace inc_misses_counter(struct bpf_prog *prog)
 {
 	struct bpf_prog_stats *stats;
+	unsigned int flags;
 
 	stats = this_cpu_ptr(prog->stats);
-	u64_stats_update_begin(&stats->syncp);
-	stats->misses++;
-	u64_stats_update_end(&stats->syncp);
+	flags = u64_stats_update_begin_irqsave(&stats->syncp);
+	u64_stats_inc(&stats->misses);
+	u64_stats_update_end_irqrestore(&stats->syncp, flags);
 }
 
 /* The logic is similar to bpf_prog_run(), but with an explicit
@@ -585,11 +580,13 @@
 	     * Hence check that 'start' is valid.
 	     */
 	    start > NO_START_TIME) {
+		unsigned long flags;
+
 		stats = this_cpu_ptr(prog->stats);
-		u64_stats_update_begin(&stats->syncp);
-		stats->cnt++;
-		stats->nsecs += sched_clock() - start;
-		u64_stats_update_end(&stats->syncp);
+		flags = u64_stats_update_begin_irqsave(&stats->syncp);
+		u64_stats_inc(&stats->cnt);
+		u64_stats_add(&stats->nsecs, sched_clock() - start);
+		u64_stats_update_end_irqrestore(&stats->syncp, flags);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/bpf/verifier.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/bpf/verifier.c
@@ -240,12 +240,6 @@
 	       insn->src_reg == BPF_PSEUDO_KFUNC_CALL;
 }
 
-static bool bpf_pseudo_func(const struct bpf_insn *insn)
-{
-	return insn->code == (BPF_LD | BPF_IMM | BPF_DW) &&
-	       insn->src_reg == BPF_PSEUDO_FUNC;
-}
-
 struct bpf_call_arg_meta {
 	struct bpf_map *map_ptr;
 	bool raw_mode;
@@ -445,18 +439,6 @@
 		type == PTR_TO_SOCK_COMMON;
 }
 
-static bool reg_type_may_be_null(enum bpf_reg_type type)
-{
-	return type == PTR_TO_MAP_VALUE_OR_NULL ||
-	       type == PTR_TO_SOCKET_OR_NULL ||
-	       type == PTR_TO_SOCK_COMMON_OR_NULL ||
-	       type == PTR_TO_TCP_SOCK_OR_NULL ||
-	       type == PTR_TO_BTF_ID_OR_NULL ||
-	       type == PTR_TO_MEM_OR_NULL ||
-	       type == PTR_TO_RDONLY_BUF_OR_NULL ||
-	       type == PTR_TO_RDWR_BUF_OR_NULL;
-}
-
 static bool reg_may_point_to_spin_lock(const struct bpf_reg_state *reg)
 {
 	return reg->type == PTR_TO_MAP_VALUE &&
@@ -465,12 +447,14 @@
 
 static bool reg_type_may_be_refcounted_or_null(enum bpf_reg_type type)
 {
-	return type == PTR_TO_SOCKET ||
-		type == PTR_TO_SOCKET_OR_NULL ||
-		type == PTR_TO_TCP_SOCK ||
-		type == PTR_TO_TCP_SOCK_OR_NULL ||
-		type == PTR_TO_MEM ||
-		type == PTR_TO_MEM_OR_NULL;
+	return base_type(type) == PTR_TO_SOCKET ||
+		base_type(type) == PTR_TO_TCP_SOCK ||
+		base_type(type) == PTR_TO_MEM;
+}
+
+static bool type_is_rdonly_mem(u32 type)
+{
+	return type & MEM_RDONLY;
 }
 
 static bool arg_type_may_be_refcounted(enum bpf_arg_type type)
@@ -478,14 +462,9 @@
 	return type == ARG_PTR_TO_SOCK_COMMON;
 }
 
-static bool arg_type_may_be_null(enum bpf_arg_type type)
+static bool type_may_be_null(u32 type)
 {
-	return type == ARG_PTR_TO_MAP_VALUE_OR_NULL ||
-	       type == ARG_PTR_TO_MEM_OR_NULL ||
-	       type == ARG_PTR_TO_CTX_OR_NULL ||
-	       type == ARG_PTR_TO_SOCKET_OR_NULL ||
-	       type == ARG_PTR_TO_ALLOC_MEM_OR_NULL ||
-	       type == ARG_PTR_TO_STACK_OR_NULL;
+	return type & PTR_MAYBE_NULL;
 }
 
 /* Determine whether the function releases some resources allocated by another
@@ -538,6 +517,12 @@
 		func_id == BPF_FUNC_skc_to_tcp_request_sock;
 }
 
+static bool is_callback_calling_function(enum bpf_func_id func_id)
+{
+	return func_id == BPF_FUNC_for_each_map_elem ||
+	       func_id == BPF_FUNC_timer_set_callback;
+}
+
 static bool is_cmpxchg_insn(const struct bpf_insn *insn)
 {
 	return BPF_CLASS(insn->code) == BPF_STX &&
@@ -545,39 +530,56 @@
 	       insn->imm == BPF_CMPXCHG;
 }
 
-/* string representation of 'enum bpf_reg_type' */
-static const char * const reg_type_str[] = {
-	[NOT_INIT]		= "?",
-	[SCALAR_VALUE]		= "inv",
-	[PTR_TO_CTX]		= "ctx",
-	[CONST_PTR_TO_MAP]	= "map_ptr",
-	[PTR_TO_MAP_VALUE]	= "map_value",
-	[PTR_TO_MAP_VALUE_OR_NULL] = "map_value_or_null",
-	[PTR_TO_STACK]		= "fp",
-	[PTR_TO_PACKET]		= "pkt",
-	[PTR_TO_PACKET_META]	= "pkt_meta",
-	[PTR_TO_PACKET_END]	= "pkt_end",
-	[PTR_TO_FLOW_KEYS]	= "flow_keys",
-	[PTR_TO_SOCKET]		= "sock",
-	[PTR_TO_SOCKET_OR_NULL] = "sock_or_null",
-	[PTR_TO_SOCK_COMMON]	= "sock_common",
-	[PTR_TO_SOCK_COMMON_OR_NULL] = "sock_common_or_null",
-	[PTR_TO_TCP_SOCK]	= "tcp_sock",
-	[PTR_TO_TCP_SOCK_OR_NULL] = "tcp_sock_or_null",
-	[PTR_TO_TP_BUFFER]	= "tp_buffer",
-	[PTR_TO_XDP_SOCK]	= "xdp_sock",
-	[PTR_TO_BTF_ID]		= "ptr_",
-	[PTR_TO_BTF_ID_OR_NULL]	= "ptr_or_null_",
-	[PTR_TO_PERCPU_BTF_ID]	= "percpu_ptr_",
-	[PTR_TO_MEM]		= "mem",
-	[PTR_TO_MEM_OR_NULL]	= "mem_or_null",
-	[PTR_TO_RDONLY_BUF]	= "rdonly_buf",
-	[PTR_TO_RDONLY_BUF_OR_NULL] = "rdonly_buf_or_null",
-	[PTR_TO_RDWR_BUF]	= "rdwr_buf",
-	[PTR_TO_RDWR_BUF_OR_NULL] = "rdwr_buf_or_null",
-	[PTR_TO_FUNC]		= "func",
-	[PTR_TO_MAP_KEY]	= "map_key",
-};
+/* string representation of 'enum bpf_reg_type'
+ *
+ * Note that reg_type_str() can not appear more than once in a single verbose()
+ * statement.
+ */
+static const char *reg_type_str(struct bpf_verifier_env *env,
+				enum bpf_reg_type type)
+{
+	char postfix[16] = {0}, prefix[16] = {0};
+	static const char * const str[] = {
+		[NOT_INIT]		= "?",
+		[SCALAR_VALUE]		= "inv",
+		[PTR_TO_CTX]		= "ctx",
+		[CONST_PTR_TO_MAP]	= "map_ptr",
+		[PTR_TO_MAP_VALUE]	= "map_value",
+		[PTR_TO_STACK]		= "fp",
+		[PTR_TO_PACKET]		= "pkt",
+		[PTR_TO_PACKET_META]	= "pkt_meta",
+		[PTR_TO_PACKET_END]	= "pkt_end",
+		[PTR_TO_FLOW_KEYS]	= "flow_keys",
+		[PTR_TO_SOCKET]		= "sock",
+		[PTR_TO_SOCK_COMMON]	= "sock_common",
+		[PTR_TO_TCP_SOCK]	= "tcp_sock",
+		[PTR_TO_TP_BUFFER]	= "tp_buffer",
+		[PTR_TO_XDP_SOCK]	= "xdp_sock",
+		[PTR_TO_BTF_ID]		= "ptr_",
+		[PTR_TO_PERCPU_BTF_ID]	= "percpu_ptr_",
+		[PTR_TO_MEM]		= "mem",
+		[PTR_TO_BUF]		= "buf",
+		[PTR_TO_FUNC]		= "func",
+		[PTR_TO_MAP_KEY]	= "map_key",
+	};
+
+	if (type & PTR_MAYBE_NULL) {
+		if (base_type(type) == PTR_TO_BTF_ID ||
+		    base_type(type) == PTR_TO_PERCPU_BTF_ID)
+			strncpy(postfix, "or_null_", 16);
+		else
+			strncpy(postfix, "_or_null", 16);
+	}
+
+	if (type & MEM_RDONLY)
+		strncpy(prefix, "rdonly_", 16);
+	if (type & MEM_ALLOC)
+		strncpy(prefix, "alloc_", 16);
+
+	snprintf(env->type_str_buf, TYPE_STR_BUF_LEN, "%s%s%s",
+		 prefix, str[base_type(type)], postfix);
+	return env->type_str_buf;
+}
 
 static char slot_type_char[] = {
 	[STACK_INVALID]	= '?',
@@ -612,6 +614,20 @@
 	return btf_name_by_offset(btf, btf_type_by_id(btf, id)->name_off);
 }
 
+/* The reg state of a pointer or a bounded scalar was saved when
+ * it was spilled to the stack.
+ */
+static bool is_spilled_reg(const struct bpf_stack_state *stack)
+{
+	return stack->slot_type[BPF_REG_SIZE - 1] == STACK_SPILL;
+}
+
+static void scrub_spilled_slot(u8 *stype)
+{
+	if (*stype != STACK_INVALID)
+		*stype = STACK_MISC;
+}
+
 static void print_verifier_state(struct bpf_verifier_env *env,
 				 const struct bpf_func_state *state)
 {
@@ -628,7 +644,7 @@
 			continue;
 		verbose(env, " R%d", i);
 		print_liveness(env, reg->live);
-		verbose(env, "=%s", reg_type_str[t]);
+		verbose(env, "=%s", reg_type_str(env, t));
 		if (t == SCALAR_VALUE && reg->precise)
 			verbose(env, "P");
 		if ((t == SCALAR_VALUE || t == PTR_TO_STACK) &&
@@ -636,9 +652,8 @@
 			/* reg->off should be 0 for SCALAR_VALUE */
 			verbose(env, "%lld", reg->var_off.value + reg->off);
 		} else {
-			if (t == PTR_TO_BTF_ID ||
-			    t == PTR_TO_BTF_ID_OR_NULL ||
-			    t == PTR_TO_PERCPU_BTF_ID)
+			if (base_type(t) == PTR_TO_BTF_ID ||
+			    base_type(t) == PTR_TO_PERCPU_BTF_ID)
 				verbose(env, "%s", kernel_type_name(reg->btf, reg->btf_id));
 			verbose(env, "(id=%d", reg->id);
 			if (reg_type_may_be_refcounted_or_null(t))
@@ -647,10 +662,9 @@
 				verbose(env, ",off=%d", reg->off);
 			if (type_is_pkt_pointer(t))
 				verbose(env, ",r=%d", reg->range);
-			else if (t == CONST_PTR_TO_MAP ||
-				 t == PTR_TO_MAP_KEY ||
-				 t == PTR_TO_MAP_VALUE ||
-				 t == PTR_TO_MAP_VALUE_OR_NULL)
+			else if (base_type(t) == CONST_PTR_TO_MAP ||
+				 base_type(t) == PTR_TO_MAP_KEY ||
+				 base_type(t) == PTR_TO_MAP_VALUE)
 				verbose(env, ",ks=%d,vs=%d",
 					reg->map_ptr->key_size,
 					reg->map_ptr->value_size);
@@ -717,10 +731,10 @@
 			continue;
 		verbose(env, " fp%d", (-i - 1) * BPF_REG_SIZE);
 		print_liveness(env, state->stack[i].spilled_ptr.live);
-		if (state->stack[i].slot_type[0] == STACK_SPILL) {
+		if (is_spilled_reg(&state->stack[i])) {
 			reg = &state->stack[i].spilled_ptr;
 			t = reg->type;
-			verbose(env, "=%s", reg_type_str[t]);
+			verbose(env, "=%s", reg_type_str(env, t));
 			if (t == SCALAR_VALUE && reg->precise)
 				verbose(env, "P");
 			if (t == SCALAR_VALUE && tnum_is_const(reg->var_off))
@@ -778,12 +792,17 @@
  */
 static void *realloc_array(void *arr, size_t old_n, size_t new_n, size_t size)
 {
+	void *new_arr;
+
 	if (!new_n || old_n == new_n)
 		goto out;
 
-	arr = krealloc_array(arr, new_n, size, GFP_KERNEL);
-	if (!arr)
+	new_arr = krealloc_array(arr, new_n, size, GFP_KERNEL);
+	if (!new_arr) {
+		kfree(arr);
 		return NULL;
+	}
+	arr = new_arr;
 
 	if (new_n > old_n)
 		memset(arr + old_n * size, 0, (new_n - old_n) * size);
@@ -859,6 +878,7 @@
 	id = ++env->id_gen;
 	state->refs[new_ofs].id = id;
 	state->refs[new_ofs].insn_idx = insn_idx;
+	state->refs[new_ofs].callback_ref = state->in_callback_fn ? state->frameno : 0;
 
 	return id;
 }
@@ -871,6 +891,9 @@
 	last_idx = state->acquired_refs - 1;
 	for (i = 0; i < state->acquired_refs; i++) {
 		if (state->refs[i].id == ptr_id) {
+			/* Cannot release caller references in callbacks */
+			if (state->in_callback_fn && state->refs[i].callback_ref != state->frameno)
+				return -EINVAL;
 			if (last_idx && i != last_idx)
 				memcpy(&state->refs[i], &state->refs[last_idx],
 				       sizeof(*state->refs));
@@ -1133,8 +1156,7 @@
 
 static void mark_ptr_not_null_reg(struct bpf_reg_state *reg)
 {
-	switch (reg->type) {
-	case PTR_TO_MAP_VALUE_OR_NULL: {
+	if (base_type(reg->type) == PTR_TO_MAP_VALUE) {
 		const struct bpf_map *map = reg->map_ptr;
 
 		if (map->inner_map_meta) {
@@ -1143,7 +1165,8 @@
 			/* transfer reg's id which is unique for every map_lookup_elem
 			 * as UID of the inner map.
 			 */
-			reg->map_uid = reg->id;
+			if (map_value_has_timer(map->inner_map_meta))
+				reg->map_uid = reg->id;
 		} else if (map->map_type == BPF_MAP_TYPE_XSKMAP) {
 			reg->type = PTR_TO_XDP_SOCK;
 		} else if (map->map_type == BPF_MAP_TYPE_SOCKMAP ||
@@ -1152,32 +1175,10 @@
 		} else {
 			reg->type = PTR_TO_MAP_VALUE;
 		}
-		break;
-	}
-	case PTR_TO_SOCKET_OR_NULL:
-		reg->type = PTR_TO_SOCKET;
-		break;
-	case PTR_TO_SOCK_COMMON_OR_NULL:
-		reg->type = PTR_TO_SOCK_COMMON;
-		break;
-	case PTR_TO_TCP_SOCK_OR_NULL:
-		reg->type = PTR_TO_TCP_SOCK;
-		break;
-	case PTR_TO_BTF_ID_OR_NULL:
-		reg->type = PTR_TO_BTF_ID;
-		break;
-	case PTR_TO_MEM_OR_NULL:
-		reg->type = PTR_TO_MEM;
-		break;
-	case PTR_TO_RDONLY_BUF_OR_NULL:
-		reg->type = PTR_TO_RDONLY_BUF;
-		break;
-	case PTR_TO_RDWR_BUF_OR_NULL:
-		reg->type = PTR_TO_RDWR_BUF;
-		break;
-	default:
-		WARN_ONCE(1, "unknown nullable register type");
+		return;
 	}
+
+	reg->type &= ~PTR_MAYBE_NULL;
 }
 
 static bool reg_is_pkt_pointer(const struct bpf_reg_state *reg)
@@ -1357,22 +1358,43 @@
 	reg->var_off = tnum_or(tnum_clear_subreg(var64_off), var32_off);
 }
 
+static void reg_bounds_sync(struct bpf_reg_state *reg)
+{
+	/* We might have learned new bounds from the var_off. */
+	__update_reg_bounds(reg);
+	/* We might have learned something about the sign bit. */
+	__reg_deduce_bounds(reg);
+	/* We might have learned some bits from the bounds. */
+	__reg_bound_offset(reg);
+	/* Intersecting with the old var_off might have improved our bounds
+	 * slightly, e.g. if umax was 0x7f...f and var_off was (0; 0xf...fc),
+	 * then new var_off is (0; 0x7f...fc) which improves our umax.
+	 */
+	__update_reg_bounds(reg);
+}
+
+static bool __reg32_bound_s64(s32 a)
+{
+	return a >= 0 && a <= S32_MAX;
+}
+
 static void __reg_assign_32_into_64(struct bpf_reg_state *reg)
 {
 	reg->umin_value = reg->u32_min_value;
 	reg->umax_value = reg->u32_max_value;
-	/* Attempt to pull 32-bit signed bounds into 64-bit bounds
-	 * but must be positive otherwise set to worse case bounds
-	 * and refine later from tnum.
+
+	/* Attempt to pull 32-bit signed bounds into 64-bit bounds but must
+	 * be positive otherwise set to worse case bounds and refine later
+	 * from tnum.
 	 */
-	if (reg->s32_min_value >= 0 && reg->s32_max_value >= 0)
-		reg->smax_value = reg->s32_max_value;
-	else
-		reg->smax_value = U32_MAX;
-	if (reg->s32_min_value >= 0)
+	if (__reg32_bound_s64(reg->s32_min_value) &&
+	    __reg32_bound_s64(reg->s32_max_value)) {
 		reg->smin_value = reg->s32_min_value;
-	else
+		reg->smax_value = reg->s32_max_value;
+	} else {
 		reg->smin_value = 0;
+		reg->smax_value = U32_MAX;
+	}
 }
 
 static void __reg_combine_32_into_64(struct bpf_reg_state *reg)
@@ -1392,32 +1414,23 @@
 		 * so they do not impact tnum bounds calculation.
 		 */
 		__mark_reg64_unbounded(reg);
-		__update_reg_bounds(reg);
 	}
-
-	/* Intersecting with the old var_off might have improved our bounds
-	 * slightly.  e.g. if umax was 0x7f...f and var_off was (0; 0xf...fc),
-	 * then new var_off is (0; 0x7f...fc) which improves our umax.
-	 */
-	__reg_deduce_bounds(reg);
-	__reg_bound_offset(reg);
-	__update_reg_bounds(reg);
+	reg_bounds_sync(reg);
 }
 
 static bool __reg64_bound_s32(s64 a)
 {
-	return a > S32_MIN && a < S32_MAX;
+	return a >= S32_MIN && a <= S32_MAX;
 }
 
 static bool __reg64_bound_u32(u64 a)
 {
-	return a > U32_MIN && a < U32_MAX;
+	return a >= U32_MIN && a <= U32_MAX;
 }
 
 static void __reg_combine_64_into_32(struct bpf_reg_state *reg)
 {
 	__mark_reg32_unbounded(reg);
-
 	if (__reg64_bound_s32(reg->smin_value) && __reg64_bound_s32(reg->smax_value)) {
 		reg->s32_min_value = (s32)reg->smin_value;
 		reg->s32_max_value = (s32)reg->smax_value;
@@ -1426,14 +1439,7 @@
 		reg->u32_min_value = (u32)reg->umin_value;
 		reg->u32_max_value = (u32)reg->umax_value;
 	}
-
-	/* Intersecting with the old var_off might have improved our bounds
-	 * slightly.  e.g. if umax was 0x7f...f and var_off was (0; 0xf...fc),
-	 * then new var_off is (0; 0x7f...fc) which improves our umax.
-	 */
-	__reg_deduce_bounds(reg);
-	__reg_bound_offset(reg);
-	__update_reg_bounds(reg);
+	reg_bounds_sync(reg);
 }
 
 /* Mark a register as having a completely unknown (scalar) value. */
@@ -1448,7 +1454,7 @@
 	reg->type = SCALAR_VALUE;
 	reg->var_off = tnum_unknown;
 	reg->frameno = 0;
-	reg->precise = env->subprog_cnt > 1 || !env->bpf_capable;
+	reg->precise = !env->bpf_capable;
 	__mark_reg_unbounded(reg);
 }
 
@@ -1807,16 +1813,10 @@
 			return -EPERM;
 		}
 
-		if (bpf_pseudo_func(insn)) {
-			ret = add_subprog(env, i + insn->imm + 1);
-			if (ret >= 0)
-				/* remember subprog */
-				insn[1].imm = ret;
-		} else if (bpf_pseudo_call(insn)) {
+		if (bpf_pseudo_func(insn) || bpf_pseudo_call(insn))
 			ret = add_subprog(env, i + insn->imm + 1);
-		} else {
+		else
 			ret = add_kfunc_call(env, insn->imm);
-		}
 
 		if (ret < 0)
 			return ret;
@@ -1899,7 +1899,7 @@
 			break;
 		if (parent->live & REG_LIVE_DONE) {
 			verbose(env, "verifier BUG type %s var_off %lld off %d\n",
-				reg_type_str[parent->type],
+				reg_type_str(env, parent->type),
 				parent->var_off.value, parent->off);
 			return -EFAULT;
 		}
@@ -2191,7 +2191,12 @@
 	if (class == BPF_ALU || class == BPF_ALU64) {
 		if (!(*reg_mask & dreg))
 			return 0;
-		if (opcode == BPF_MOV) {
+		if (opcode == BPF_END || opcode == BPF_NEG) {
+			/* sreg is reserved and unused
+			 * dreg still need precision before this insn
+			 */
+			return 0;
+		} else if (opcode == BPF_MOV) {
 			if (BPF_SRC(insn->code) == BPF_X) {
 				/* dreg = sreg
 				 * dreg needs precision after this insn
@@ -2232,8 +2237,6 @@
 		 */
 		if (insn->src_reg != BPF_REG_FP)
 			return 0;
-		if (BPF_SIZE(insn->code) != BPF_DW)
-			return 0;
 
 		/* dreg = *(u64 *)[fp - off] was a fill from the stack.
 		 * that [fp - off] slot contains scalar that needs to be
@@ -2256,8 +2259,6 @@
 		/* scalars can only be spilled into stack */
 		if (insn->dst_reg != BPF_REG_FP)
 			return 0;
-		if (BPF_SIZE(insn->code) != BPF_DW)
-			return 0;
 		spi = (-insn->off - 1) / BPF_REG_SIZE;
 		if (spi >= 64) {
 			verbose(env, "BUG spi %d\n", spi);
@@ -2273,6 +2274,17 @@
 		if (opcode == BPF_CALL) {
 			if (insn->src_reg == BPF_PSEUDO_CALL)
 				return -ENOTSUPP;
+			/* kfunc with imm==0 is invalid and fixup_kfunc_call will
+			 * catch this error later. Make backtracking conservative
+			 * with ENOTSUPP.
+			 */
+			if (insn->src_reg == BPF_PSEUDO_KFUNC_CALL && insn->imm == 0)
+				return -ENOTSUPP;
+			/* BPF helpers that invoke callback subprogs are
+			 * equivalent to BPF_PSEUDO_CALL above
+			 */
+			if (insn->src_reg == 0 && is_callback_calling_function(insn->imm))
+				return -ENOTSUPP;
 			/* regular helper call sets R0 */
 			*reg_mask &= ~1;
 			if (*reg_mask & 0x3f) {
@@ -2285,6 +2297,21 @@
 			}
 		} else if (opcode == BPF_EXIT) {
 			return -ENOTSUPP;
+		} else if (BPF_SRC(insn->code) == BPF_X) {
+			if (!(*reg_mask & (dreg | sreg)))
+				return 0;
+			/* dreg <cond> sreg
+			 * Both dreg and sreg need precision before
+			 * this insn. If only sreg was marked precise
+			 * before it would be equally necessary to
+			 * propagate it to dreg.
+			 */
+			*reg_mask |= (sreg | dreg);
+			 /* else dreg <cond> K
+			  * Only dreg still needs precision before
+			  * this insn, so for the K-based conditional
+			  * there is nothing new to be marked.
+			  */
 		}
 	} else if (class == BPF_LD) {
 		if (!(*reg_mask & dreg))
@@ -2362,8 +2389,11 @@
 
 	/* big hammer: mark all scalars precise in this path.
 	 * pop_stack may still get !precise scalars.
+	 * We also skip current state and go straight to first parent state,
+	 * because precision markings in current non-checkpointed state are
+	 * not needed. See why in the comment in __mark_chain_precision below.
 	 */
-	for (; st; st = st->parent)
+	for (st = st->parent; st; st = st->parent) {
 		for (i = 0; i <= st->curframe; i++) {
 			func = st->frame[i];
 			for (j = 0; j < BPF_REG_FP; j++) {
@@ -2373,7 +2403,7 @@
 				reg->precise = true;
 			}
 			for (j = 0; j < func->allocated_stack / BPF_REG_SIZE; j++) {
-				if (func->stack[j].slot_type[0] != STACK_SPILL)
+				if (!is_spilled_reg(&func->stack[j]))
 					continue;
 				reg = &func->stack[j].spilled_ptr;
 				if (reg->type != SCALAR_VALUE)
@@ -2381,9 +2411,122 @@
 				reg->precise = true;
 			}
 		}
+	}
+}
+
+static void mark_all_scalars_imprecise(struct bpf_verifier_env *env, struct bpf_verifier_state *st)
+{
+	struct bpf_func_state *func;
+	struct bpf_reg_state *reg;
+	int i, j;
+
+	for (i = 0; i <= st->curframe; i++) {
+		func = st->frame[i];
+		for (j = 0; j < BPF_REG_FP; j++) {
+			reg = &func->regs[j];
+			if (reg->type != SCALAR_VALUE)
+				continue;
+			reg->precise = false;
+		}
+		for (j = 0; j < func->allocated_stack / BPF_REG_SIZE; j++) {
+			if (!is_spilled_reg(&func->stack[j]))
+				continue;
+			reg = &func->stack[j].spilled_ptr;
+			if (reg->type != SCALAR_VALUE)
+				continue;
+			reg->precise = false;
+		}
+	}
 }
 
-static int __mark_chain_precision(struct bpf_verifier_env *env, int regno,
+/*
+ * __mark_chain_precision() backtracks BPF program instruction sequence and
+ * chain of verifier states making sure that register *regno* (if regno >= 0)
+ * and/or stack slot *spi* (if spi >= 0) are marked as precisely tracked
+ * SCALARS, as well as any other registers and slots that contribute to
+ * a tracked state of given registers/stack slots, depending on specific BPF
+ * assembly instructions (see backtrack_insns() for exact instruction handling
+ * logic). This backtracking relies on recorded jmp_history and is able to
+ * traverse entire chain of parent states. This process ends only when all the
+ * necessary registers/slots and their transitive dependencies are marked as
+ * precise.
+ *
+ * One important and subtle aspect is that precise marks *do not matter* in
+ * the currently verified state (current state). It is important to understand
+ * why this is the case.
+ *
+ * First, note that current state is the state that is not yet "checkpointed",
+ * i.e., it is not yet put into env->explored_states, and it has no children
+ * states as well. It's ephemeral, and can end up either a) being discarded if
+ * compatible explored state is found at some point or BPF_EXIT instruction is
+ * reached or b) checkpointed and put into env->explored_states, branching out
+ * into one or more children states.
+ *
+ * In the former case, precise markings in current state are completely
+ * ignored by state comparison code (see regsafe() for details). Only
+ * checkpointed ("old") state precise markings are important, and if old
+ * state's register/slot is precise, regsafe() assumes current state's
+ * register/slot as precise and checks value ranges exactly and precisely. If
+ * states turn out to be compatible, current state's necessary precise
+ * markings and any required parent states' precise markings are enforced
+ * after the fact with propagate_precision() logic, after the fact. But it's
+ * important to realize that in this case, even after marking current state
+ * registers/slots as precise, we immediately discard current state. So what
+ * actually matters is any of the precise markings propagated into current
+ * state's parent states, which are always checkpointed (due to b) case above).
+ * As such, for scenario a) it doesn't matter if current state has precise
+ * markings set or not.
+ *
+ * Now, for the scenario b), checkpointing and forking into child(ren)
+ * state(s). Note that before current state gets to checkpointing step, any
+ * processed instruction always assumes precise SCALAR register/slot
+ * knowledge: if precise value or range is useful to prune jump branch, BPF
+ * verifier takes this opportunity enthusiastically. Similarly, when
+ * register's value is used to calculate offset or memory address, exact
+ * knowledge of SCALAR range is assumed, checked, and enforced. So, similar to
+ * what we mentioned above about state comparison ignoring precise markings
+ * during state comparison, BPF verifier ignores and also assumes precise
+ * markings *at will* during instruction verification process. But as verifier
+ * assumes precision, it also propagates any precision dependencies across
+ * parent states, which are not yet finalized, so can be further restricted
+ * based on new knowledge gained from restrictions enforced by their children
+ * states. This is so that once those parent states are finalized, i.e., when
+ * they have no more active children state, state comparison logic in
+ * is_state_visited() would enforce strict and precise SCALAR ranges, if
+ * required for correctness.
+ *
+ * To build a bit more intuition, note also that once a state is checkpointed,
+ * the path we took to get to that state is not important. This is crucial
+ * property for state pruning. When state is checkpointed and finalized at
+ * some instruction index, it can be correctly and safely used to "short
+ * circuit" any *compatible* state that reaches exactly the same instruction
+ * index. I.e., if we jumped to that instruction from a completely different
+ * code path than original finalized state was derived from, it doesn't
+ * matter, current state can be discarded because from that instruction
+ * forward having a compatible state will ensure we will safely reach the
+ * exit. States describe preconditions for further exploration, but completely
+ * forget the history of how we got here.
+ *
+ * This also means that even if we needed precise SCALAR range to get to
+ * finalized state, but from that point forward *that same* SCALAR register is
+ * never used in a precise context (i.e., it's precise value is not needed for
+ * correctness), it's correct and safe to mark such register as "imprecise"
+ * (i.e., precise marking set to false). This is what we rely on when we do
+ * not set precise marking in current state. If no child state requires
+ * precision for any given SCALAR register, it's safe to dictate that it can
+ * be imprecise. If any child state does require this register to be precise,
+ * we'll mark it precise later retroactively during precise markings
+ * propagation from child state to parent states.
+ *
+ * Skipping precise marking setting in current state is a mild version of
+ * relying on the above observation. But we can utilize this property even
+ * more aggressively by proactively forgetting any precise marking in the
+ * current state (which we inherited from the parent state), right before we
+ * checkpoint it and branch off into new child state. This is done by
+ * mark_all_scalars_imprecise() to hopefully get more permissive and generic
+ * finalized states which help in short circuiting more future states.
+ */
+static int __mark_chain_precision(struct bpf_verifier_env *env, int frame, int regno,
 				  int spi)
 {
 	struct bpf_verifier_state *st = env->cur_state;
@@ -2400,22 +2543,22 @@
 	if (!env->bpf_capable)
 		return 0;
 
-	func = st->frame[st->curframe];
+	/* Do sanity checks against current state of register and/or stack
+	 * slot, but don't set precise flag in current state, as precision
+	 * tracking in the current state is unnecessary.
+	 */
+	func = st->frame[frame];
 	if (regno >= 0) {
 		reg = &func->regs[regno];
 		if (reg->type != SCALAR_VALUE) {
 			WARN_ONCE(1, "backtracing misuse");
 			return -EFAULT;
 		}
-		if (!reg->precise)
-			new_marks = true;
-		else
-			reg_mask = 0;
-		reg->precise = true;
+		new_marks = true;
 	}
 
 	while (spi >= 0) {
-		if (func->stack[spi].slot_type[0] != STACK_SPILL) {
+		if (!is_spilled_reg(&func->stack[spi])) {
 			stack_mask = 0;
 			break;
 		}
@@ -2424,11 +2567,7 @@
 			stack_mask = 0;
 			break;
 		}
-		if (!reg->precise)
-			new_marks = true;
-		else
-			stack_mask = 0;
-		reg->precise = true;
+		new_marks = true;
 		break;
 	}
 
@@ -2436,12 +2575,42 @@
 		return 0;
 	if (!reg_mask && !stack_mask)
 		return 0;
+
 	for (;;) {
 		DECLARE_BITMAP(mask, 64);
 		u32 history = st->jmp_history_cnt;
 
 		if (env->log.level & BPF_LOG_LEVEL)
 			verbose(env, "last_idx %d first_idx %d\n", last_idx, first_idx);
+
+		if (last_idx < 0) {
+			/* we are at the entry into subprog, which
+			 * is expected for global funcs, but only if
+			 * requested precise registers are R1-R5
+			 * (which are global func's input arguments)
+			 */
+			if (st->curframe == 0 &&
+			    st->frame[0]->subprogno > 0 &&
+			    st->frame[0]->callsite == BPF_MAIN_FUNC &&
+			    stack_mask == 0 && (reg_mask & ~0x3e) == 0) {
+				bitmap_from_u64(mask, reg_mask);
+				for_each_set_bit(i, mask, 32) {
+					reg = &st->frame[0]->regs[i];
+					if (reg->type != SCALAR_VALUE) {
+						reg_mask &= ~(1u << i);
+						continue;
+					}
+					reg->precise = true;
+				}
+				return 0;
+			}
+
+			verbose(env, "BUG backtracing func entry subprog %d reg_mask %x stack_mask %llx\n",
+				st->frame[0]->subprogno, reg_mask, stack_mask);
+			WARN_ONCE(1, "verifier backtracking bug");
+			return -EFAULT;
+		}
+
 		for (i = last_idx;;) {
 			if (skip_first) {
 				err = 0;
@@ -2481,7 +2650,7 @@
 			break;
 
 		new_marks = false;
-		func = st->frame[st->curframe];
+		func = st->frame[frame];
 		bitmap_from_u64(mask, reg_mask);
 		for_each_set_bit(i, mask, 32) {
 			reg = &func->regs[i];
@@ -2514,7 +2683,7 @@
 				return 0;
 			}
 
-			if (func->stack[i].slot_type[0] != STACK_SPILL) {
+			if (!is_spilled_reg(&func->stack[i])) {
 				stack_mask &= ~(1ull << i);
 				continue;
 			}
@@ -2547,19 +2716,23 @@
 
 static int mark_chain_precision(struct bpf_verifier_env *env, int regno)
 {
-	return __mark_chain_precision(env, regno, -1);
+	return __mark_chain_precision(env, env->cur_state->curframe, regno, -1);
 }
 
-static int mark_chain_precision_stack(struct bpf_verifier_env *env, int spi)
+static int mark_chain_precision_frame(struct bpf_verifier_env *env, int frame, int regno)
 {
-	return __mark_chain_precision(env, -1, spi);
+	return __mark_chain_precision(env, frame, regno, -1);
+}
+
+static int mark_chain_precision_stack_frame(struct bpf_verifier_env *env, int frame, int spi)
+{
+	return __mark_chain_precision(env, frame, -1, spi);
 }
 
 static bool is_spillable_regtype(enum bpf_reg_type type)
 {
-	switch (type) {
+	switch (base_type(type)) {
 	case PTR_TO_MAP_VALUE:
-	case PTR_TO_MAP_VALUE_OR_NULL:
 	case PTR_TO_STACK:
 	case PTR_TO_CTX:
 	case PTR_TO_PACKET:
@@ -2568,21 +2741,13 @@
 	case PTR_TO_FLOW_KEYS:
 	case CONST_PTR_TO_MAP:
 	case PTR_TO_SOCKET:
-	case PTR_TO_SOCKET_OR_NULL:
 	case PTR_TO_SOCK_COMMON:
-	case PTR_TO_SOCK_COMMON_OR_NULL:
 	case PTR_TO_TCP_SOCK:
-	case PTR_TO_TCP_SOCK_OR_NULL:
 	case PTR_TO_XDP_SOCK:
 	case PTR_TO_BTF_ID:
-	case PTR_TO_BTF_ID_OR_NULL:
-	case PTR_TO_RDONLY_BUF:
-	case PTR_TO_RDONLY_BUF_OR_NULL:
-	case PTR_TO_RDWR_BUF:
-	case PTR_TO_RDWR_BUF_OR_NULL:
+	case PTR_TO_BUF:
 	case PTR_TO_PERCPU_BTF_ID:
 	case PTR_TO_MEM:
-	case PTR_TO_MEM_OR_NULL:
 	case PTR_TO_FUNC:
 	case PTR_TO_MAP_KEY:
 		return true;
@@ -2625,16 +2790,38 @@
 	return reg->type != SCALAR_VALUE;
 }
 
+/* Copy src state preserving dst->parent and dst->live fields */
+static void copy_register_state(struct bpf_reg_state *dst, const struct bpf_reg_state *src)
+{
+	struct bpf_reg_state *parent = dst->parent;
+	enum bpf_reg_liveness live = dst->live;
+
+	*dst = *src;
+	dst->parent = parent;
+	dst->live = live;
+}
+
 static void save_register_state(struct bpf_func_state *state,
-				int spi, struct bpf_reg_state *reg)
+				int spi, struct bpf_reg_state *reg,
+				int size)
 {
 	int i;
 
-	state->stack[spi].spilled_ptr = *reg;
-	state->stack[spi].spilled_ptr.live |= REG_LIVE_WRITTEN;
+	copy_register_state(&state->stack[spi].spilled_ptr, reg);
+	if (size == BPF_REG_SIZE)
+		state->stack[spi].spilled_ptr.live |= REG_LIVE_WRITTEN;
 
-	for (i = 0; i < BPF_REG_SIZE; i++)
-		state->stack[spi].slot_type[i] = STACK_SPILL;
+	for (i = BPF_REG_SIZE; i > BPF_REG_SIZE - size; i--)
+		state->stack[spi].slot_type[i - 1] = STACK_SPILL;
+
+	/* size < 8 bytes spill */
+	for (; i; i--)
+		scrub_spilled_slot(&state->stack[spi].slot_type[i - 1]);
+}
+
+static bool is_bpf_st_mem(struct bpf_insn *insn)
+{
+	return BPF_CLASS(insn->code) == BPF_ST && BPF_MODE(insn->code) == BPF_MEM;
 }
 
 /* check_stack_{read,write}_fixed_off functions track spill/fill of registers,
@@ -2648,8 +2835,9 @@
 {
 	struct bpf_func_state *cur; /* state of the current function */
 	int i, slot = -off - 1, spi = slot / BPF_REG_SIZE, err;
-	u32 dst_reg = env->prog->insnsi[insn_idx].dst_reg;
+	struct bpf_insn *insn = &env->prog->insnsi[insn_idx];
 	struct bpf_reg_state *reg = NULL;
+	u32 dst_reg = insn->dst_reg;
 
 	err = grow_stack_state(state, round_up(slot + 1, BPF_REG_SIZE));
 	if (err)
@@ -2658,7 +2846,7 @@
 	 * so it's aligned access and [off, off + size) are within stack limits
 	 */
 	if (!env->allow_ptr_leaks &&
-	    state->stack[spi].slot_type[0] == STACK_SPILL &&
+	    is_spilled_reg(&state->stack[spi]) &&
 	    size != BPF_REG_SIZE) {
 		verbose(env, "attempt to corrupt spilled pointer on stack\n");
 		return -EACCES;
@@ -2671,7 +2859,9 @@
 		bool sanitize = reg && is_spillable_regtype(reg->type);
 
 		for (i = 0; i < size; i++) {
-			if (state->stack[spi].slot_type[i] == STACK_INVALID) {
+			u8 type = state->stack[spi].slot_type[i];
+
+			if (type != STACK_MISC && type != STACK_ZERO) {
 				sanitize = true;
 				break;
 			}
@@ -2681,7 +2871,7 @@
 			env->insn_aux_data[insn_idx].sanitize_stack_spill = true;
 	}
 
-	if (reg && size == BPF_REG_SIZE && register_is_bounded(reg) &&
+	if (reg && !(off % BPF_REG_SIZE) && register_is_bounded(reg) &&
 	    !register_is_null(reg) && env->bpf_capable) {
 		if (dst_reg != BPF_REG_FP) {
 			/* The backtracking logic can only recognize explicit
@@ -2694,7 +2884,17 @@
 			if (err)
 				return err;
 		}
-		save_register_state(state, spi, reg);
+		save_register_state(state, spi, reg, size);
+		/* Break the relation on a narrowing spill. */
+		if (fls64(reg->umax_value) > BITS_PER_BYTE * size)
+			state->stack[spi].spilled_ptr.id = 0;
+	} else if (!reg && !(off % BPF_REG_SIZE) && is_bpf_st_mem(insn) &&
+		   insn->imm != 0 && env->bpf_capable) {
+		struct bpf_reg_state fake_reg = {};
+
+		__mark_reg_known(&fake_reg, insn->imm);
+		fake_reg.type = SCALAR_VALUE;
+		save_register_state(state, spi, &fake_reg, size);
 	} else if (reg && is_spillable_regtype(reg->type)) {
 		/* register containing pointer is being spilled into stack */
 		if (size != BPF_REG_SIZE) {
@@ -2706,16 +2906,16 @@
 			verbose(env, "cannot spill pointers to stack into stack frame of the caller\n");
 			return -EINVAL;
 		}
-		save_register_state(state, spi, reg);
+		save_register_state(state, spi, reg, size);
 	} else {
 		u8 type = STACK_MISC;
 
 		/* regular write of data into stack destroys any spilled ptr */
 		state->stack[spi].spilled_ptr.type = NOT_INIT;
 		/* Mark slots as STACK_MISC if they belonged to spilled ptr. */
-		if (state->stack[spi].slot_type[0] == STACK_SPILL)
+		if (is_spilled_reg(&state->stack[spi]))
 			for (i = 0; i < BPF_REG_SIZE; i++)
-				state->stack[spi].slot_type[i] = STACK_MISC;
+				scrub_spilled_slot(&state->stack[spi].slot_type[i]);
 
 		/* only mark the slot as written if all 8 bytes were written
 		 * otherwise read propagation may incorrectly stop too soon
@@ -2729,7 +2929,8 @@
 			state->stack[spi].spilled_ptr.live |= REG_LIVE_WRITTEN;
 
 		/* when we zero initialize stack slots mark them as such */
-		if (reg && register_is_null(reg)) {
+		if ((reg && register_is_null(reg)) ||
+		    (!reg && is_bpf_st_mem(insn) && insn->imm == 0)) {
 			/* backtracking doesn't work for STACK_ZERO yet. */
 			err = mark_chain_precision(env, value_regno);
 			if (err)
@@ -2803,14 +3004,17 @@
 		spi = slot / BPF_REG_SIZE;
 		stype = &state->stack[spi].slot_type[slot % BPF_REG_SIZE];
 
-		if (!env->allow_ptr_leaks
-				&& *stype != NOT_INIT
-				&& *stype != SCALAR_VALUE) {
-			/* Reject the write if there's are spilled pointers in
-			 * range. If we didn't reject here, the ptr status
-			 * would be erased below (even though not all slots are
-			 * actually overwritten), possibly opening the door to
-			 * leaks.
+		if (!env->allow_ptr_leaks && *stype != STACK_MISC && *stype != STACK_ZERO) {
+			/* Reject the write if range we may write to has not
+			 * been initialized beforehand. If we didn't reject
+			 * here, the ptr status would be erased below (even
+			 * though not all slots are actually overwritten),
+			 * possibly opening the door to leaks.
+			 *
+			 * We do however catch STACK_INVALID case below, and
+			 * only allow reading possibly uninitialized memory
+			 * later for CAP_PERFMON, as the write may not happen to
+			 * that slot.
 			 */
 			verbose(env, "spilled ptr in range of var-offset stack write; insn %d, ptr off: %d",
 				insn_idx, i);
@@ -2918,35 +3122,56 @@
 	struct bpf_func_state *state = vstate->frame[vstate->curframe];
 	int i, slot = -off - 1, spi = slot / BPF_REG_SIZE;
 	struct bpf_reg_state *reg;
-	u8 *stype;
+	u8 *stype, type;
 
 	stype = reg_state->stack[spi].slot_type;
 	reg = &reg_state->stack[spi].spilled_ptr;
 
-	if (stype[0] == STACK_SPILL) {
-		if (size != BPF_REG_SIZE) {
+	if (is_spilled_reg(&reg_state->stack[spi])) {
+		u8 spill_size = 1;
+
+		for (i = BPF_REG_SIZE - 1; i > 0 && stype[i - 1] == STACK_SPILL; i--)
+			spill_size++;
+
+		if (size != BPF_REG_SIZE || spill_size != BPF_REG_SIZE) {
 			if (reg->type != SCALAR_VALUE) {
 				verbose_linfo(env, env->insn_idx, "; ");
 				verbose(env, "invalid size of register fill\n");
 				return -EACCES;
 			}
-			if (dst_regno >= 0) {
+
+			mark_reg_read(env, reg, reg->parent, REG_LIVE_READ64);
+			if (dst_regno < 0)
+				return 0;
+
+			if (!(off % BPF_REG_SIZE) && size == spill_size) {
+				/* The earlier check_reg_arg() has decided the
+				 * subreg_def for this insn.  Save it first.
+				 */
+				s32 subreg_def = state->regs[dst_regno].subreg_def;
+
+				copy_register_state(&state->regs[dst_regno], reg);
+				state->regs[dst_regno].subreg_def = subreg_def;
+			} else {
+				for (i = 0; i < size; i++) {
+					type = stype[(slot - i) % BPF_REG_SIZE];
+					if (type == STACK_SPILL)
+						continue;
+					if (type == STACK_MISC)
+						continue;
+					verbose(env, "invalid read from stack off %d+%d size %d\n",
+						off, i, size);
+					return -EACCES;
+				}
 				mark_reg_unknown(env, state->regs, dst_regno);
-				state->regs[dst_regno].live |= REG_LIVE_WRITTEN;
 			}
-			mark_reg_read(env, reg, reg->parent, REG_LIVE_READ64);
+			state->regs[dst_regno].live |= REG_LIVE_WRITTEN;
 			return 0;
 		}
-		for (i = 1; i < BPF_REG_SIZE; i++) {
-			if (stype[(slot - i) % BPF_REG_SIZE] != STACK_SPILL) {
-				verbose(env, "corrupted spill memory\n");
-				return -EACCES;
-			}
-		}
 
 		if (dst_regno >= 0) {
 			/* restore register state from stack */
-			state->regs[dst_regno] = *reg;
+			copy_register_state(&state->regs[dst_regno], reg);
 			/* mark reg as written since spilled pointer state likely
 			 * has its liveness marks cleared by is_state_visited()
 			 * which resets stack/reg liveness for state transitions
@@ -2965,8 +3190,6 @@
 		}
 		mark_reg_read(env, reg, reg->parent, REG_LIVE_READ64);
 	} else {
-		u8 type;
-
 		for (i = 0; i < size; i++) {
 			type = stype[(slot - i) % BPF_REG_SIZE];
 			if (type == STACK_MISC)
@@ -3068,17 +3291,13 @@
 	}
 	/* Variable offset is prohibited for unprivileged mode for simplicity
 	 * since it requires corresponding support in Spectre masking for stack
-	 * ALU. See also retrieve_ptr_limit().
+	 * ALU. See also retrieve_ptr_limit(). The check in
+	 * check_stack_access_for_ptr_arithmetic() called by
+	 * adjust_ptr_min_max_vals() prevents users from creating stack pointers
+	 * with variable offsets, therefore no check is required here. Further,
+	 * just checking it here would be insufficient as speculative stack
+	 * writes could still lead to unsafe speculative behaviour.
 	 */
-	if (!env->bypass_spec_v1 && var_off) {
-		char tn_buf[48];
-
-		tnum_strn(tn_buf, sizeof(tn_buf), reg->var_off);
-		verbose(env, "R%d variable offset stack access prohibited for !root, var_off=%s\n",
-				ptr_regno, tn_buf);
-		return -EACCES;
-	}
-
 	if (!var_off) {
 		off += reg->var_off.value;
 		err = check_stack_read_fixed_off(env, state, off, size,
@@ -3398,7 +3617,7 @@
 		 */
 		*reg_type = info.reg_type;
 
-		if (*reg_type == PTR_TO_BTF_ID || *reg_type == PTR_TO_BTF_ID_OR_NULL) {
+		if (base_type(*reg_type) == PTR_TO_BTF_ID) {
 			*btf = info.btf;
 			*btf_id = info.btf_id;
 		} else {
@@ -3466,7 +3685,7 @@
 	}
 
 	verbose(env, "R%d invalid %s access off=%d size=%d\n",
-		regno, reg_type_str[reg->type], off, size);
+		regno, reg_type_str(env, reg->type), off, size);
 
 	return -EACCES;
 }
@@ -3685,7 +3904,7 @@
 continue_func:
 	subprog_end = subprog[idx + 1].start;
 	for (; i < subprog_end; i++) {
-		int next_insn;
+		int next_insn, sidx;
 
 		if (!bpf_pseudo_call(insn + i) && !bpf_pseudo_func(insn + i))
 			continue;
@@ -3695,21 +3914,23 @@
 
 		/* find the callee */
 		next_insn = i + insn[i].imm + 1;
-		idx = find_subprog(env, next_insn);
-		if (idx < 0) {
+		sidx = find_subprog(env, next_insn);
+		if (sidx < 0) {
 			WARN_ONCE(1, "verifier bug. No program starts at insn %d\n",
 				  next_insn);
 			return -EFAULT;
 		}
-		if (subprog[idx].is_async_cb) {
-			if (subprog[idx].has_tail_call) {
+		if (subprog[sidx].is_async_cb) {
+			if (subprog[sidx].has_tail_call) {
 				verbose(env, "verifier bug. subprog has tail_call and async cb\n");
 				return -EFAULT;
 			}
-			 /* async callbacks don't increase bpf prog stack size */
-			continue;
+			/* async callbacks don't increase bpf prog stack size unless called directly */
+			if (!bpf_pseudo_call(insn + i))
+				continue;
 		}
 		i = next_insn;
+		idx = sidx;
 
 		if (subprog[idx].has_tail_call)
 			tail_call_reachable = true;
@@ -3761,16 +3982,17 @@
 }
 #endif
 
-int check_ctx_reg(struct bpf_verifier_env *env,
-		  const struct bpf_reg_state *reg, int regno)
+static int __check_ptr_off_reg(struct bpf_verifier_env *env,
+			       const struct bpf_reg_state *reg, int regno,
+			       bool fixed_off_ok)
 {
-	/* Access to ctx or passing it to a helper is only allowed in
-	 * its original, unmodified form.
+	/* Access to this pointer-typed register or passing it to a helper
+	 * is only allowed in its original, unmodified form.
 	 */
 
-	if (reg->off) {
-		verbose(env, "dereference of modified ctx ptr R%d off=%d disallowed\n",
-			regno, reg->off);
+	if (!fixed_off_ok && reg->off) {
+		verbose(env, "dereference of modified %s ptr R%d off=%d disallowed\n",
+			reg_type_str(env, reg->type), regno, reg->off);
 		return -EACCES;
 	}
 
@@ -3778,13 +4000,20 @@
 		char tn_buf[48];
 
 		tnum_strn(tn_buf, sizeof(tn_buf), reg->var_off);
-		verbose(env, "variable ctx access var_off=%s disallowed\n", tn_buf);
+		verbose(env, "variable %s access var_off=%s disallowed\n",
+			reg_type_str(env, reg->type), tn_buf);
 		return -EACCES;
 	}
 
 	return 0;
 }
 
+int check_ptr_off_reg(struct bpf_verifier_env *env,
+		      const struct bpf_reg_state *reg, int regno)
+{
+	return __check_ptr_off_reg(env, reg, regno, false);
+}
+
 static int __check_buffer_access(struct bpf_verifier_env *env,
 				 const char *buf_info,
 				 const struct bpf_reg_state *reg,
@@ -3884,7 +4113,22 @@
 
 static bool bpf_map_is_rdonly(const struct bpf_map *map)
 {
-	return (map->map_flags & BPF_F_RDONLY_PROG) && map->frozen;
+	/* A map is considered read-only if the following condition are true:
+	 *
+	 * 1) BPF program side cannot change any of the map content. The
+	 *    BPF_F_RDONLY_PROG flag is throughout the lifetime of a map
+	 *    and was set at map creation time.
+	 * 2) The map value(s) have been initialized from user space by a
+	 *    loader and then "frozen", such that no new map update/delete
+	 *    operations from syscall side are possible for the rest of
+	 *    the map's lifetime from that point onwards.
+	 * 3) Any parallel/pending map update/delete operations from syscall
+	 *    side have been completed. Only after that point, it's safe to
+	 *    assume that map value(s) are immutable.
+	 */
+	return (map->map_flags & BPF_F_RDONLY_PROG) &&
+	       READ_ONCE(map->frozen) &&
+	       !bpf_map_write_active(map);
 }
 
 static int bpf_map_direct_read(struct bpf_map *map, int off, int size, u64 *val)
@@ -4071,10 +4315,7 @@
 
 	if (tnum_is_const(reg->var_off)) {
 		min_off = reg->var_off.value + off;
-		if (access_size > 0)
-			max_off = min_off + access_size - 1;
-		else
-			max_off = min_off;
+		max_off = min_off + access_size;
 	} else {
 		if (reg->smax_value >= BPF_MAX_VAR_OFF ||
 		    reg->smin_value <= -BPF_MAX_VAR_OFF) {
@@ -4083,15 +4324,17 @@
 			return -EACCES;
 		}
 		min_off = reg->smin_value + off;
-		if (access_size > 0)
-			max_off = reg->smax_value + off + access_size - 1;
-		else
-			max_off = min_off;
+		max_off = reg->smax_value + off + access_size;
 	}
 
 	err = check_stack_slot_within_bounds(min_off, state, type);
-	if (!err)
-		err = check_stack_slot_within_bounds(max_off, state, type);
+	if (!err && max_off > 0)
+		err = -EINVAL; /* out of stack access into non-negative offsets */
+	if (!err && access_size < 0)
+		/* access_size should not be negative (or overflow an int); others checks
+		 * along the way should have prevented such an access.
+		 */
+		err = -EFAULT; /* invalid negative access size; integer overflow? */
 
 	if (err) {
 		if (tnum_is_const(reg->var_off)) {
@@ -4178,15 +4421,30 @@
 				mark_reg_unknown(env, regs, value_regno);
 			}
 		}
-	} else if (reg->type == PTR_TO_MEM) {
+	} else if (base_type(reg->type) == PTR_TO_MEM) {
+		bool rdonly_mem = type_is_rdonly_mem(reg->type);
+
+		if (type_may_be_null(reg->type)) {
+			verbose(env, "R%d invalid mem access '%s'\n", regno,
+				reg_type_str(env, reg->type));
+			return -EACCES;
+		}
+
+		if (t == BPF_WRITE && rdonly_mem) {
+			verbose(env, "R%d cannot write into %s\n",
+				regno, reg_type_str(env, reg->type));
+			return -EACCES;
+		}
+
 		if (t == BPF_WRITE && value_regno >= 0 &&
 		    is_pointer_value(env, value_regno)) {
 			verbose(env, "R%d leaks addr into mem\n", value_regno);
 			return -EACCES;
 		}
+
 		err = check_mem_region_access(env, regno, off, size,
 					      reg->mem_size, false);
-		if (!err && t == BPF_READ && value_regno >= 0)
+		if (!err && value_regno >= 0 && (t == BPF_READ || rdonly_mem))
 			mark_reg_unknown(env, regs, value_regno);
 	} else if (reg->type == PTR_TO_CTX) {
 		enum bpf_reg_type reg_type = SCALAR_VALUE;
@@ -4199,7 +4457,7 @@
 			return -EACCES;
 		}
 
-		err = check_ctx_reg(env, reg, regno);
+		err = check_ptr_off_reg(env, reg, regno);
 		if (err < 0)
 			return err;
 
@@ -4216,7 +4474,7 @@
 			} else {
 				mark_reg_known_zero(env, regs,
 						    value_regno);
-				if (reg_type_may_be_null(reg_type))
+				if (type_may_be_null(reg_type))
 					regs[value_regno].id = ++env->id_gen;
 				/* A load of ctx field could have different
 				 * actual load size with the one encoded in the
@@ -4224,8 +4482,7 @@
 				 * a sub-register.
 				 */
 				regs[value_regno].subreg_def = DEF_NOT_SUBREG;
-				if (reg_type == PTR_TO_BTF_ID ||
-				    reg_type == PTR_TO_BTF_ID_OR_NULL) {
+				if (base_type(reg_type) == PTR_TO_BTF_ID) {
 					regs[value_regno].btf = btf;
 					regs[value_regno].btf_id = btf_id;
 				}
@@ -4278,7 +4535,7 @@
 	} else if (type_is_sk_pointer(reg->type)) {
 		if (t == BPF_WRITE) {
 			verbose(env, "R%d cannot write into %s\n",
-				regno, reg_type_str[reg->type]);
+				regno, reg_type_str(env, reg->type));
 			return -EACCES;
 		}
 		err = check_sock_access(env, insn_idx, regno, off, size, t);
@@ -4294,26 +4551,32 @@
 	} else if (reg->type == CONST_PTR_TO_MAP) {
 		err = check_ptr_to_map_access(env, regs, regno, off, size, t,
 					      value_regno);
-	} else if (reg->type == PTR_TO_RDONLY_BUF) {
-		if (t == BPF_WRITE) {
-			verbose(env, "R%d cannot write into %s\n",
-				regno, reg_type_str[reg->type]);
-			return -EACCES;
+	} else if (base_type(reg->type) == PTR_TO_BUF) {
+		bool rdonly_mem = type_is_rdonly_mem(reg->type);
+		const char *buf_info;
+		u32 *max_access;
+
+		if (rdonly_mem) {
+			if (t == BPF_WRITE) {
+				verbose(env, "R%d cannot write into %s\n",
+					regno, reg_type_str(env, reg->type));
+				return -EACCES;
+			}
+			buf_info = "rdonly";
+			max_access = &env->prog->aux->max_rdonly_access;
+		} else {
+			buf_info = "rdwr";
+			max_access = &env->prog->aux->max_rdwr_access;
 		}
+
 		err = check_buffer_access(env, reg, regno, off, size, false,
-					  "rdonly",
-					  &env->prog->aux->max_rdonly_access);
-		if (!err && value_regno >= 0)
-			mark_reg_unknown(env, regs, value_regno);
-	} else if (reg->type == PTR_TO_RDWR_BUF) {
-		err = check_buffer_access(env, reg, regno, off, size, false,
-					  "rdwr",
-					  &env->prog->aux->max_rdwr_access);
-		if (!err && t == BPF_READ && value_regno >= 0)
+					  buf_info, max_access);
+
+		if (!err && value_regno >= 0 && (rdonly_mem || t == BPF_READ))
 			mark_reg_unknown(env, regs, value_regno);
 	} else {
 		verbose(env, "R%d invalid mem access '%s'\n", regno,
-			reg_type_str[reg->type]);
+			reg_type_str(env, reg->type));
 		return -EACCES;
 	}
 
@@ -4364,9 +4627,16 @@
 
 	if (insn->imm == BPF_CMPXCHG) {
 		/* Check comparison of R0 with memory location */
-		err = check_reg_arg(env, BPF_REG_0, SRC_OP);
+		const u32 aux_reg = BPF_REG_0;
+
+		err = check_reg_arg(env, aux_reg, SRC_OP);
 		if (err)
 			return err;
+
+		if (is_pointer_value(env, aux_reg)) {
+			verbose(env, "R%d leaks addr into mem\n", aux_reg);
+			return -EACCES;
+		}
 	}
 
 	if (is_pointer_value(env, insn->src_reg)) {
@@ -4380,7 +4650,7 @@
 	    is_sk_reg(env, insn->dst_reg)) {
 		verbose(env, "BPF_ATOMIC stores into R%d %s is not allowed\n",
 			insn->dst_reg,
-			reg_type_str[reg_state(env, insn->dst_reg)->type]);
+			reg_type_str(env, reg_state(env, insn->dst_reg)->type));
 		return -EACCES;
 	}
 
@@ -4401,13 +4671,19 @@
 		load_reg = -1;
 	}
 
-	/* check whether we can read the memory */
+	/* Check whether we can read the memory, with second call for fetch
+	 * case to simulate the register fill.
+	 */
 	err = check_mem_access(env, insn_idx, insn->dst_reg, insn->off,
-			       BPF_SIZE(insn->code), BPF_READ, load_reg, true);
+			       BPF_SIZE(insn->code), BPF_READ, -1, true);
+	if (!err && load_reg >= 0)
+		err = check_mem_access(env, insn_idx, insn->dst_reg, insn->off,
+				       BPF_SIZE(insn->code), BPF_READ, load_reg,
+				       true);
 	if (err)
 		return err;
 
-	/* check whether we can write into the same memory */
+	/* Check whether we can write into the same memory. */
 	err = check_mem_access(env, insn_idx, insn->dst_reg, insn->off,
 			       BPF_SIZE(insn->code), BPF_WRITE, -1, true);
 	if (err)
@@ -4514,17 +4790,17 @@
 			goto mark;
 		}
 
-		if (state->stack[spi].slot_type[0] == STACK_SPILL &&
+		if (is_spilled_reg(&state->stack[spi]) &&
 		    state->stack[spi].spilled_ptr.type == PTR_TO_BTF_ID)
 			goto mark;
 
-		if (state->stack[spi].slot_type[0] == STACK_SPILL &&
+		if (is_spilled_reg(&state->stack[spi]) &&
 		    (state->stack[spi].spilled_ptr.type == SCALAR_VALUE ||
 		     env->allow_ptr_leaks)) {
 			if (clobber) {
 				__mark_reg_unknown(env, &state->stack[spi].spilled_ptr);
 				for (j = 0; j < BPF_REG_SIZE; j++)
-					state->stack[spi].slot_type[j] = STACK_MISC;
+					scrub_spilled_slot(&state->stack[spi].slot_type[j]);
 			}
 			goto mark;
 		}
@@ -4557,13 +4833,20 @@
 				   struct bpf_call_arg_meta *meta)
 {
 	struct bpf_reg_state *regs = cur_regs(env), *reg = &regs[regno];
+	const char *buf_info;
+	u32 *max_access;
 
-	switch (reg->type) {
+	switch (base_type(reg->type)) {
 	case PTR_TO_PACKET:
 	case PTR_TO_PACKET_META:
 		return check_packet_access(env, regno, reg->off, access_size,
 					   zero_size_allowed);
 	case PTR_TO_MAP_KEY:
+		if (meta && meta->raw_mode) {
+			verbose(env, "R%d cannot write into %s\n", regno,
+				reg_type_str(env, reg->type));
+			return -EACCES;
+		}
 		return check_mem_region_access(env, regno, reg->off, access_size,
 					       reg->map_ptr->key_size, false);
 	case PTR_TO_MAP_VALUE:
@@ -4574,21 +4857,33 @@
 		return check_map_access(env, regno, reg->off, access_size,
 					zero_size_allowed);
 	case PTR_TO_MEM:
+		if (type_is_rdonly_mem(reg->type)) {
+			if (meta && meta->raw_mode) {
+				verbose(env, "R%d cannot write into %s\n", regno,
+					reg_type_str(env, reg->type));
+				return -EACCES;
+			}
+		}
 		return check_mem_region_access(env, regno, reg->off,
 					       access_size, reg->mem_size,
 					       zero_size_allowed);
-	case PTR_TO_RDONLY_BUF:
-		if (meta && meta->raw_mode)
-			return -EACCES;
-		return check_buffer_access(env, reg, regno, reg->off,
-					   access_size, zero_size_allowed,
-					   "rdonly",
-					   &env->prog->aux->max_rdonly_access);
-	case PTR_TO_RDWR_BUF:
+	case PTR_TO_BUF:
+		if (type_is_rdonly_mem(reg->type)) {
+			if (meta && meta->raw_mode) {
+				verbose(env, "R%d cannot write into %s\n", regno,
+					reg_type_str(env, reg->type));
+				return -EACCES;
+			}
+
+			buf_info = "rdonly";
+			max_access = &env->prog->aux->max_rdonly_access;
+		} else {
+			buf_info = "rdwr";
+			max_access = &env->prog->aux->max_rdwr_access;
+		}
 		return check_buffer_access(env, reg, regno, reg->off,
 					   access_size, zero_size_allowed,
-					   "rdwr",
-					   &env->prog->aux->max_rdwr_access);
+					   buf_info, max_access);
 	case PTR_TO_STACK:
 		return check_stack_range_initialized(
 				env,
@@ -4600,9 +4895,9 @@
 		    register_is_null(reg))
 			return 0;
 
-		verbose(env, "R%d type=%s expected=%s\n", regno,
-			reg_type_str[reg->type],
-			reg_type_str[PTR_TO_STACK]);
+		verbose(env, "R%d type=%s ", regno,
+			reg_type_str(env, reg->type));
+		verbose(env, "expected=%s\n", reg_type_str(env, PTR_TO_STACK));
 		return -EACCES;
 	}
 }
@@ -4613,7 +4908,7 @@
 	if (register_is_null(reg))
 		return 0;
 
-	if (reg_type_may_be_null(reg->type)) {
+	if (type_may_be_null(reg->type)) {
 		/* Assuming that the register contains a value check if the memory
 		 * access is safe. Temporarily save and restore the register's state as
 		 * the conversion shouldn't be visible to a caller.
@@ -4761,9 +5056,8 @@
 
 static bool arg_type_is_mem_ptr(enum bpf_arg_type type)
 {
-	return type == ARG_PTR_TO_MEM ||
-	       type == ARG_PTR_TO_MEM_OR_NULL ||
-	       type == ARG_PTR_TO_UNINIT_MEM;
+	return base_type(type) == ARG_PTR_TO_MEM ||
+	       base_type(type) == ARG_PTR_TO_UNINIT_MEM;
 }
 
 static bool arg_type_is_mem_size(enum bpf_arg_type type)
@@ -4865,8 +5159,8 @@
 		PTR_TO_MAP_KEY,
 		PTR_TO_MAP_VALUE,
 		PTR_TO_MEM,
-		PTR_TO_RDONLY_BUF,
-		PTR_TO_RDWR_BUF,
+		PTR_TO_MEM | MEM_ALLOC,
+		PTR_TO_BUF,
 	},
 };
 
@@ -4883,7 +5177,7 @@
 static const struct bpf_reg_types fullsock_types = { .types = { PTR_TO_SOCKET } };
 static const struct bpf_reg_types scalar_types = { .types = { SCALAR_VALUE } };
 static const struct bpf_reg_types context_types = { .types = { PTR_TO_CTX } };
-static const struct bpf_reg_types alloc_mem_types = { .types = { PTR_TO_MEM } };
+static const struct bpf_reg_types alloc_mem_types = { .types = { PTR_TO_MEM | MEM_ALLOC } };
 static const struct bpf_reg_types const_map_ptr_types = { .types = { CONST_PTR_TO_MAP } };
 static const struct bpf_reg_types btf_ptr_types = { .types = { PTR_TO_BTF_ID } };
 static const struct bpf_reg_types spin_lock_types = { .types = { PTR_TO_MAP_VALUE } };
@@ -4897,31 +5191,26 @@
 	[ARG_PTR_TO_MAP_KEY]		= &map_key_value_types,
 	[ARG_PTR_TO_MAP_VALUE]		= &map_key_value_types,
 	[ARG_PTR_TO_UNINIT_MAP_VALUE]	= &map_key_value_types,
-	[ARG_PTR_TO_MAP_VALUE_OR_NULL]	= &map_key_value_types,
 	[ARG_CONST_SIZE]		= &scalar_types,
 	[ARG_CONST_SIZE_OR_ZERO]	= &scalar_types,
 	[ARG_CONST_ALLOC_SIZE_OR_ZERO]	= &scalar_types,
 	[ARG_CONST_MAP_PTR]		= &const_map_ptr_types,
 	[ARG_PTR_TO_CTX]		= &context_types,
-	[ARG_PTR_TO_CTX_OR_NULL]	= &context_types,
 	[ARG_PTR_TO_SOCK_COMMON]	= &sock_types,
 #ifdef CONFIG_NET
 	[ARG_PTR_TO_BTF_ID_SOCK_COMMON]	= &btf_id_sock_common_types,
 #endif
 	[ARG_PTR_TO_SOCKET]		= &fullsock_types,
-	[ARG_PTR_TO_SOCKET_OR_NULL]	= &fullsock_types,
 	[ARG_PTR_TO_BTF_ID]		= &btf_ptr_types,
 	[ARG_PTR_TO_SPIN_LOCK]		= &spin_lock_types,
 	[ARG_PTR_TO_MEM]		= &mem_types,
-	[ARG_PTR_TO_MEM_OR_NULL]	= &mem_types,
 	[ARG_PTR_TO_UNINIT_MEM]		= &mem_types,
 	[ARG_PTR_TO_ALLOC_MEM]		= &alloc_mem_types,
-	[ARG_PTR_TO_ALLOC_MEM_OR_NULL]	= &alloc_mem_types,
 	[ARG_PTR_TO_INT]		= &int_ptr_types,
 	[ARG_PTR_TO_LONG]		= &int_ptr_types,
 	[ARG_PTR_TO_PERCPU_BTF_ID]	= &percpu_btf_ptr_types,
 	[ARG_PTR_TO_FUNC]		= &func_ptr_types,
-	[ARG_PTR_TO_STACK_OR_NULL]	= &stack_ptr_types,
+	[ARG_PTR_TO_STACK]		= &stack_ptr_types,
 	[ARG_PTR_TO_CONST_STR]		= &const_str_ptr_types,
 	[ARG_PTR_TO_TIMER]		= &timer_types,
 };
@@ -4935,12 +5224,27 @@
 	const struct bpf_reg_types *compatible;
 	int i, j;
 
-	compatible = compatible_reg_types[arg_type];
+	compatible = compatible_reg_types[base_type(arg_type)];
 	if (!compatible) {
 		verbose(env, "verifier internal error: unsupported arg type %d\n", arg_type);
 		return -EFAULT;
 	}
 
+	/* ARG_PTR_TO_MEM + RDONLY is compatible with PTR_TO_MEM and PTR_TO_MEM + RDONLY,
+	 * but ARG_PTR_TO_MEM is compatible only with PTR_TO_MEM and NOT with PTR_TO_MEM + RDONLY
+	 *
+	 * Same for MAYBE_NULL:
+	 *
+	 * ARG_PTR_TO_MEM + MAYBE_NULL is compatible with PTR_TO_MEM and PTR_TO_MEM + MAYBE_NULL,
+	 * but ARG_PTR_TO_MEM is compatible only with PTR_TO_MEM but NOT with PTR_TO_MEM + MAYBE_NULL
+	 *
+	 * Therefore we fold these flags depending on the arg_type before comparison.
+	 */
+	if (arg_type & MEM_RDONLY)
+		type &= ~MEM_RDONLY;
+	if (arg_type & PTR_MAYBE_NULL)
+		type &= ~PTR_MAYBE_NULL;
+
 	for (i = 0; i < ARRAY_SIZE(compatible->types); i++) {
 		expected = compatible->types[i];
 		if (expected == NOT_INIT)
@@ -4950,14 +5254,14 @@
 			goto found;
 	}
 
-	verbose(env, "R%d type=%s expected=", regno, reg_type_str[type]);
+	verbose(env, "R%d type=%s expected=", regno, reg_type_str(env, reg->type));
 	for (j = 0; j + 1 < i; j++)
-		verbose(env, "%s, ", reg_type_str[compatible->types[j]]);
-	verbose(env, "%s\n", reg_type_str[compatible->types[j]]);
+		verbose(env, "%s, ", reg_type_str(env, compatible->types[j]));
+	verbose(env, "%s\n", reg_type_str(env, compatible->types[j]));
 	return -EACCES;
 
 found:
-	if (type == PTR_TO_BTF_ID) {
+	if (reg->type == PTR_TO_BTF_ID) {
 		if (!arg_btf_id) {
 			if (!compatible->btf_id) {
 				verbose(env, "verifier internal error: missing arg compatible BTF ID\n");
@@ -4973,12 +5277,6 @@
 				kernel_type_name(btf_vmlinux, *arg_btf_id));
 			return -EACCES;
 		}
-
-		if (!tnum_is_const(reg->var_off) || reg->var_off.value) {
-			verbose(env, "R%d is a pointer to in-kernel struct with non-zero offset\n",
-				regno);
-			return -EACCES;
-		}
 	}
 
 	return 0;
@@ -5016,28 +5314,58 @@
 		return -EACCES;
 	}
 
-	if (arg_type == ARG_PTR_TO_MAP_VALUE ||
-	    arg_type == ARG_PTR_TO_UNINIT_MAP_VALUE ||
-	    arg_type == ARG_PTR_TO_MAP_VALUE_OR_NULL) {
+	if (base_type(arg_type) == ARG_PTR_TO_MAP_VALUE ||
+	    base_type(arg_type) == ARG_PTR_TO_UNINIT_MAP_VALUE) {
 		err = resolve_map_arg_type(env, meta, &arg_type);
 		if (err)
 			return err;
 	}
 
-	if (register_is_null(reg) && arg_type_may_be_null(arg_type))
+	if (register_is_null(reg) && type_may_be_null(arg_type))
 		/* A NULL register has a SCALAR_VALUE type, so skip
 		 * type checking.
 		 */
 		goto skip_type_check;
 
+	/* We already checked for NULL above */
+	if (arg_type == ARG_PTR_TO_ALLOC_MEM) {
+		if (reg->off != 0 || !tnum_is_const(reg->var_off)) {
+			verbose(env, "helper wants pointer to allocated memory\n");
+			return -EACCES;
+		}
+	}
+
 	err = check_reg_type(env, regno, arg_type, fn->arg_btf_id[arg]);
 	if (err)
 		return err;
 
-	if (type == PTR_TO_CTX) {
-		err = check_ctx_reg(env, reg, regno);
+	switch ((u32)type) {
+	case SCALAR_VALUE:
+	/* Pointer types where reg offset is explicitly allowed: */
+	case PTR_TO_PACKET:
+	case PTR_TO_PACKET_META:
+	case PTR_TO_MAP_KEY:
+	case PTR_TO_MAP_VALUE:
+	case PTR_TO_MEM:
+	case PTR_TO_MEM | MEM_RDONLY:
+	case PTR_TO_MEM | MEM_ALLOC:
+	case PTR_TO_BUF:
+	case PTR_TO_BUF | MEM_RDONLY:
+	case PTR_TO_STACK:
+		/* Some of the argument types nevertheless require a
+		 * zero register offset.
+		 */
+		if (arg_type == ARG_PTR_TO_ALLOC_MEM)
+			goto force_off_check;
+		break;
+	/* All the rest must be rejected: */
+	default:
+force_off_check:
+		err = __check_ptr_off_reg(env, reg, regno,
+					  type == PTR_TO_BTF_ID);
 		if (err < 0)
 			return err;
+		break;
 	}
 
 skip_type_check:
@@ -5093,10 +5421,11 @@
 		err = check_helper_mem_access(env, regno,
 					      meta->map_ptr->key_size, false,
 					      NULL);
-	} else if (arg_type == ARG_PTR_TO_MAP_VALUE ||
-		   (arg_type == ARG_PTR_TO_MAP_VALUE_OR_NULL &&
-		    !register_is_null(reg)) ||
-		   arg_type == ARG_PTR_TO_UNINIT_MAP_VALUE) {
+	} else if (base_type(arg_type) == ARG_PTR_TO_MAP_VALUE ||
+		   base_type(arg_type) == ARG_PTR_TO_UNINIT_MAP_VALUE) {
+		if (type_may_be_null(arg_type) && register_is_null(reg))
+			return 0;
+
 		/* bpf_map_xxx(..., map_ptr, ..., value) call:
 		 * check [value, value + map->value_size) validity
 		 */
@@ -5247,7 +5576,8 @@
 	enum bpf_attach_type eatype = env->prog->expected_attach_type;
 	enum bpf_prog_type type = resolve_prog_type(env->prog);
 
-	if (func_id != BPF_FUNC_map_update_elem)
+	if (func_id != BPF_FUNC_map_update_elem &&
+	    func_id != BPF_FUNC_map_delete_elem)
 		return false;
 
 	/* It's not possible to get access to a locked struct sock in these
@@ -5258,6 +5588,11 @@
 		if (eatype == BPF_TRACE_ITER)
 			return true;
 		break;
+	case BPF_PROG_TYPE_SOCK_OPS:
+		/* map_update allowed only via dedicated helpers with event type checks */
+		if (func_id == BPF_FUNC_map_delete_elem)
+			return true;
+		break;
 	case BPF_PROG_TYPE_SOCKET_FILTER:
 	case BPF_PROG_TYPE_SCHED_CLS:
 	case BPF_PROG_TYPE_SCHED_ACT:
@@ -5345,7 +5680,6 @@
 	case BPF_MAP_TYPE_SOCKMAP:
 		if (func_id != BPF_FUNC_sk_redirect_map &&
 		    func_id != BPF_FUNC_sock_map_update &&
-		    func_id != BPF_FUNC_map_delete_elem &&
 		    func_id != BPF_FUNC_msg_redirect_map &&
 		    func_id != BPF_FUNC_sk_select_reuseport &&
 		    func_id != BPF_FUNC_map_lookup_elem &&
@@ -5355,7 +5689,6 @@
 	case BPF_MAP_TYPE_SOCKHASH:
 		if (func_id != BPF_FUNC_sk_redirect_hash &&
 		    func_id != BPF_FUNC_sock_hash_update &&
-		    func_id != BPF_FUNC_map_delete_elem &&
 		    func_id != BPF_FUNC_msg_redirect_hash &&
 		    func_id != BPF_FUNC_sk_select_reuseport &&
 		    func_id != BPF_FUNC_map_lookup_elem &&
@@ -5590,31 +5923,15 @@
 /* Packet data might have moved, any old PTR_TO_PACKET[_META,_END]
  * are now invalid, so turn them into unknown SCALAR_VALUE.
  */
-static void __clear_all_pkt_pointers(struct bpf_verifier_env *env,
-				     struct bpf_func_state *state)
+static void clear_all_pkt_pointers(struct bpf_verifier_env *env)
 {
-	struct bpf_reg_state *regs = state->regs, *reg;
-	int i;
-
-	for (i = 0; i < MAX_BPF_REG; i++)
-		if (reg_is_pkt_pointer_any(&regs[i]))
-			mark_reg_unknown(env, regs, i);
+	struct bpf_func_state *state;
+	struct bpf_reg_state *reg;
 
-	bpf_for_each_spilled_reg(i, state, reg) {
-		if (!reg)
-			continue;
+	bpf_for_each_reg_in_vstate(env->cur_state, state, reg, ({
 		if (reg_is_pkt_pointer_any(reg))
 			__mark_reg_unknown(env, reg);
-	}
-}
-
-static void clear_all_pkt_pointers(struct bpf_verifier_env *env)
-{
-	struct bpf_verifier_state *vstate = env->cur_state;
-	int i;
-
-	for (i = 0; i <= vstate->curframe; i++)
-		__clear_all_pkt_pointers(env, vstate->frame[i]);
+	}));
 }
 
 enum {
@@ -5643,41 +5960,28 @@
 		reg->range = AT_PKT_END;
 }
 
-static void release_reg_references(struct bpf_verifier_env *env,
-				   struct bpf_func_state *state,
-				   int ref_obj_id)
-{
-	struct bpf_reg_state *regs = state->regs, *reg;
-	int i;
-
-	for (i = 0; i < MAX_BPF_REG; i++)
-		if (regs[i].ref_obj_id == ref_obj_id)
-			mark_reg_unknown(env, regs, i);
-
-	bpf_for_each_spilled_reg(i, state, reg) {
-		if (!reg)
-			continue;
-		if (reg->ref_obj_id == ref_obj_id)
-			__mark_reg_unknown(env, reg);
-	}
-}
-
 /* The pointer with the specified id has released its reference to kernel
  * resources. Identify all copies of the same pointer and clear the reference.
  */
 static int release_reference(struct bpf_verifier_env *env,
 			     int ref_obj_id)
 {
-	struct bpf_verifier_state *vstate = env->cur_state;
+	struct bpf_func_state *state;
+	struct bpf_reg_state *reg;
 	int err;
-	int i;
 
 	err = release_reference_state(cur_func(env), ref_obj_id);
 	if (err)
 		return err;
 
-	for (i = 0; i <= vstate->curframe; i++)
-		release_reg_references(env, vstate->frame[i], ref_obj_id);
+	bpf_for_each_reg_in_vstate(env->cur_state, state, reg, ({
+		if (reg->ref_obj_id == ref_obj_id) {
+			if (!env->allow_ptr_leaks)
+				__mark_reg_not_init(env, reg);
+			else
+				__mark_reg_unknown(env, reg);
+		}
+	}));
 
 	return 0;
 }
@@ -5699,6 +6003,10 @@
 				   struct bpf_func_state *callee,
 				   int insn_idx);
 
+static int set_callee_state(struct bpf_verifier_env *env,
+			    struct bpf_func_state *caller,
+			    struct bpf_func_state *callee, int insn_idx);
+
 static int __check_func_call(struct bpf_verifier_env *env, struct bpf_insn *insn,
 			     int *insn_idx, int subprog,
 			     set_callee_state_fn set_callee_state_cb)
@@ -5749,7 +6057,18 @@
 		}
 	}
 
+	/* set_callee_state is used for direct subprog calls, but we are
+	 * interested in validating only BPF helpers that can call subprogs as
+	 * callbacks
+	 */
+	if (set_callee_state_cb != set_callee_state && !is_callback_calling_function(insn->imm)) {
+		verbose(env, "verifier bug: helper %s#%d is not marked as callback-calling\n",
+			func_id_name(insn->imm), insn->imm);
+		return -EFAULT;
+	}
+
 	if (insn->code == (BPF_JMP | BPF_CALL) &&
+	    insn->src_reg == 0 &&
 	    insn->imm == BPF_FUNC_timer_set_callback) {
 		struct bpf_verifier_state *async_cb;
 
@@ -5792,11 +6111,11 @@
 	/* Transfer references to the callee */
 	err = copy_reference_state(callee, caller);
 	if (err)
-		return err;
+		goto err_out;
 
 	err = set_callee_state_cb(env, caller, callee, *insn_idx);
 	if (err)
-		return err;
+		goto err_out;
 
 	clear_caller_saved_regs(env, caller->regs);
 
@@ -5813,6 +6132,11 @@
 		print_verifier_state(env, callee);
 	}
 	return 0;
+
+err_out:
+	free_func_state(callee);
+	state->frame[state->curframe + 1] = NULL;
+	return err;
 }
 
 int map_set_for_each_callback_args(struct bpf_verifier_env *env,
@@ -5950,8 +6274,7 @@
 		return -EINVAL;
 	}
 
-	state->curframe--;
-	caller = state->frame[state->curframe];
+	caller = state->frame[state->curframe - 1];
 	if (callee->in_callback_fn) {
 		/* enforce R0 return value range [0, 1]. */
 		struct tnum range = tnum_range(0, 1);
@@ -5960,6 +6283,13 @@
 			verbose(env, "R0 not a scalar value\n");
 			return -EACCES;
 		}
+
+		/* we are going to rely on register's precise value */
+		err = mark_reg_read(env, r0, r0->parent, REG_LIVE_READ64);
+		err = err ?: mark_chain_precision(env, BPF_REG_0);
+		if (err)
+			return err;
+
 		if (!tnum_in(range, r0->var_off)) {
 			verbose_invalid_scalar(env, r0, &range, "callback return", "R0");
 			return -EINVAL;
@@ -5969,10 +6299,17 @@
 		caller->regs[BPF_REG_0] = *r0;
 	}
 
-	/* Transfer references to the caller */
-	err = copy_reference_state(caller, callee);
-	if (err)
-		return err;
+	/* callback_fn frame should have released its own additions to parent's
+	 * reference state at this point, or check_reference_leak would
+	 * complain, hence it must be the same as the caller. There is no need
+	 * to copy it back.
+	 */
+	if (!callee->in_callback_fn) {
+		/* Transfer references to the caller */
+		err = copy_reference_state(caller, callee);
+		if (err)
+			return err;
+	}
 
 	*insn_idx = callee->callsite + 1;
 	if (env->log.level & BPF_LOG_LEVEL) {
@@ -5983,7 +6320,7 @@
 	}
 	/* clear everything in the callee */
 	free_func_state(callee);
-	state->frame[state->curframe + 1] = NULL;
+	state->frame[state->curframe--] = NULL;
 	return 0;
 }
 
@@ -6005,9 +6342,7 @@
 	ret_reg->s32_max_value = meta->msize_max_value;
 	ret_reg->smin_value = -MAX_ERRNO;
 	ret_reg->s32_min_value = -MAX_ERRNO;
-	__reg_deduce_bounds(ret_reg);
-	__reg_bound_offset(ret_reg);
-	__update_reg_bounds(ret_reg);
+	reg_bounds_sync(ret_reg);
 }
 
 static int
@@ -6062,8 +6397,7 @@
 	struct bpf_insn_aux_data *aux = &env->insn_aux_data[insn_idx];
 	struct bpf_reg_state *regs = cur_regs(env), *reg;
 	struct bpf_map *map = meta->map_ptr;
-	struct tnum range;
-	u64 val;
+	u64 val, max;
 	int err;
 
 	if (func_id != BPF_FUNC_tail_call)
@@ -6073,10 +6407,11 @@
 		return -EINVAL;
 	}
 
-	range = tnum_range(0, map->max_entries - 1);
 	reg = &regs[BPF_REG_3];
+	val = reg->var_off.value;
+	max = map->max_entries;
 
-	if (!register_is_const(reg) || !tnum_in(range, reg->var_off)) {
+	if (!(register_is_const(reg) && val < max)) {
 		bpf_map_key_store(aux, BPF_MAP_KEY_POISON);
 		return 0;
 	}
@@ -6084,8 +6419,6 @@
 	err = mark_chain_precision(env, BPF_REG_3);
 	if (err)
 		return err;
-
-	val = reg->var_off.value;
 	if (bpf_map_key_unseen(aux))
 		bpf_map_key_store(aux, val);
 	else if (!bpf_map_key_poisoned(aux) &&
@@ -6097,13 +6430,20 @@
 static int check_reference_leak(struct bpf_verifier_env *env)
 {
 	struct bpf_func_state *state = cur_func(env);
+	bool refs_lingering = false;
 	int i;
 
+	if (state->frameno && !state->in_callback_fn)
+		return 0;
+
 	for (i = 0; i < state->acquired_refs; i++) {
+		if (state->in_callback_fn && state->refs[i].callback_ref != state->frameno)
+			continue;
 		verbose(env, "Unreleased reference id=%d alloc_insn=%d\n",
 			state->refs[i].id, state->refs[i].insn_idx);
+		refs_lingering = true;
 	}
-	return state->acquired_refs ? -EINVAL : 0;
+	return refs_lingering ? -EINVAL : 0;
 }
 
 static int check_bpf_snprintf_call(struct bpf_verifier_env *env,
@@ -6112,6 +6452,7 @@
 	struct bpf_reg_state *fmt_reg = &regs[BPF_REG_3];
 	struct bpf_reg_state *data_len_reg = &regs[BPF_REG_5];
 	struct bpf_map *fmt_map = fmt_reg->map_ptr;
+	struct bpf_bprintf_data data = {};
 	int err, fmt_map_off, num_args;
 	u64 fmt_addr;
 	char *fmt;
@@ -6136,7 +6477,7 @@
 	/* We are also guaranteed that fmt+fmt_map_off is NULL terminated, we
 	 * can focus on validating the format specifiers.
 	 */
-	err = bpf_bprintf_prepare(fmt, UINT_MAX, NULL, NULL, num_args);
+	err = bpf_bprintf_prepare(fmt, UINT_MAX, NULL, num_args, &data);
 	if (err < 0)
 		verbose(env, "Invalid format string\n");
 
@@ -6170,6 +6511,8 @@
 			     int *insn_idx_p)
 {
 	const struct bpf_func_proto *fn = NULL;
+	enum bpf_return_type ret_type;
+	enum bpf_type_flag ret_flag;
 	struct bpf_reg_state *regs;
 	struct bpf_call_arg_meta meta;
 	int insn_idx = *insn_idx_p;
@@ -6303,13 +6646,14 @@
 	regs[BPF_REG_0].subreg_def = DEF_NOT_SUBREG;
 
 	/* update return register (already marked as written above) */
-	if (fn->ret_type == RET_INTEGER) {
+	ret_type = fn->ret_type;
+	ret_flag = type_flag(fn->ret_type);
+	if (ret_type == RET_INTEGER) {
 		/* sets type to SCALAR_VALUE */
 		mark_reg_unknown(env, regs, BPF_REG_0);
-	} else if (fn->ret_type == RET_VOID) {
+	} else if (ret_type == RET_VOID) {
 		regs[BPF_REG_0].type = NOT_INIT;
-	} else if (fn->ret_type == RET_PTR_TO_MAP_VALUE_OR_NULL ||
-		   fn->ret_type == RET_PTR_TO_MAP_VALUE) {
+	} else if (base_type(ret_type) == RET_PTR_TO_MAP_VALUE) {
 		/* There is no offset yet applied, variable or fixed */
 		mark_reg_known_zero(env, regs, BPF_REG_0);
 		/* remember map_ptr, so that check_map_access()
@@ -6323,28 +6667,25 @@
 		}
 		regs[BPF_REG_0].map_ptr = meta.map_ptr;
 		regs[BPF_REG_0].map_uid = meta.map_uid;
-		if (fn->ret_type == RET_PTR_TO_MAP_VALUE) {
-			regs[BPF_REG_0].type = PTR_TO_MAP_VALUE;
-			if (map_value_has_spin_lock(meta.map_ptr))
-				regs[BPF_REG_0].id = ++env->id_gen;
-		} else {
-			regs[BPF_REG_0].type = PTR_TO_MAP_VALUE_OR_NULL;
+		regs[BPF_REG_0].type = PTR_TO_MAP_VALUE | ret_flag;
+		if (!type_may_be_null(ret_type) &&
+		    map_value_has_spin_lock(meta.map_ptr)) {
+			regs[BPF_REG_0].id = ++env->id_gen;
 		}
-	} else if (fn->ret_type == RET_PTR_TO_SOCKET_OR_NULL) {
+	} else if (base_type(ret_type) == RET_PTR_TO_SOCKET) {
 		mark_reg_known_zero(env, regs, BPF_REG_0);
-		regs[BPF_REG_0].type = PTR_TO_SOCKET_OR_NULL;
-	} else if (fn->ret_type == RET_PTR_TO_SOCK_COMMON_OR_NULL) {
+		regs[BPF_REG_0].type = PTR_TO_SOCKET | ret_flag;
+	} else if (base_type(ret_type) == RET_PTR_TO_SOCK_COMMON) {
 		mark_reg_known_zero(env, regs, BPF_REG_0);
-		regs[BPF_REG_0].type = PTR_TO_SOCK_COMMON_OR_NULL;
-	} else if (fn->ret_type == RET_PTR_TO_TCP_SOCK_OR_NULL) {
+		regs[BPF_REG_0].type = PTR_TO_SOCK_COMMON | ret_flag;
+	} else if (base_type(ret_type) == RET_PTR_TO_TCP_SOCK) {
 		mark_reg_known_zero(env, regs, BPF_REG_0);
-		regs[BPF_REG_0].type = PTR_TO_TCP_SOCK_OR_NULL;
-	} else if (fn->ret_type == RET_PTR_TO_ALLOC_MEM_OR_NULL) {
+		regs[BPF_REG_0].type = PTR_TO_TCP_SOCK | ret_flag;
+	} else if (base_type(ret_type) == RET_PTR_TO_ALLOC_MEM) {
 		mark_reg_known_zero(env, regs, BPF_REG_0);
-		regs[BPF_REG_0].type = PTR_TO_MEM_OR_NULL;
+		regs[BPF_REG_0].type = PTR_TO_MEM | ret_flag;
 		regs[BPF_REG_0].mem_size = meta.mem_size;
-	} else if (fn->ret_type == RET_PTR_TO_MEM_OR_BTF_ID_OR_NULL ||
-		   fn->ret_type == RET_PTR_TO_MEM_OR_BTF_ID) {
+	} else if (base_type(ret_type) == RET_PTR_TO_MEM_OR_BTF_ID) {
 		const struct btf_type *t;
 
 		mark_reg_known_zero(env, regs, BPF_REG_0);
@@ -6362,29 +6703,30 @@
 					tname, PTR_ERR(ret));
 				return -EINVAL;
 			}
-			regs[BPF_REG_0].type =
-				fn->ret_type == RET_PTR_TO_MEM_OR_BTF_ID ?
-				PTR_TO_MEM : PTR_TO_MEM_OR_NULL;
+			regs[BPF_REG_0].type = PTR_TO_MEM | ret_flag;
 			regs[BPF_REG_0].mem_size = tsize;
 		} else {
-			regs[BPF_REG_0].type =
-				fn->ret_type == RET_PTR_TO_MEM_OR_BTF_ID ?
-				PTR_TO_BTF_ID : PTR_TO_BTF_ID_OR_NULL;
+			/* MEM_RDONLY may be carried from ret_flag, but it
+			 * doesn't apply on PTR_TO_BTF_ID. Fold it, otherwise
+			 * it will confuse the check of PTR_TO_BTF_ID in
+			 * check_mem_access().
+			 */
+			ret_flag &= ~MEM_RDONLY;
+
+			regs[BPF_REG_0].type = PTR_TO_BTF_ID | ret_flag;
 			regs[BPF_REG_0].btf = meta.ret_btf;
 			regs[BPF_REG_0].btf_id = meta.ret_btf_id;
 		}
-	} else if (fn->ret_type == RET_PTR_TO_BTF_ID_OR_NULL ||
-		   fn->ret_type == RET_PTR_TO_BTF_ID) {
+	} else if (base_type(ret_type) == RET_PTR_TO_BTF_ID) {
 		int ret_btf_id;
 
 		mark_reg_known_zero(env, regs, BPF_REG_0);
-		regs[BPF_REG_0].type = fn->ret_type == RET_PTR_TO_BTF_ID ?
-						     PTR_TO_BTF_ID :
-						     PTR_TO_BTF_ID_OR_NULL;
+		regs[BPF_REG_0].type = PTR_TO_BTF_ID | ret_flag;
 		ret_btf_id = *fn->ret_btf_id;
 		if (ret_btf_id == 0) {
-			verbose(env, "invalid return type %d of func %s#%d\n",
-				fn->ret_type, func_id_name(func_id), func_id);
+			verbose(env, "invalid return type %u of func %s#%d\n",
+				base_type(ret_type), func_id_name(func_id),
+				func_id);
 			return -EINVAL;
 		}
 		/* current BPF helper definitions are only coming from
@@ -6393,12 +6735,12 @@
 		regs[BPF_REG_0].btf = btf_vmlinux;
 		regs[BPF_REG_0].btf_id = ret_btf_id;
 	} else {
-		verbose(env, "unknown return type %d of func %s#%d\n",
-			fn->ret_type, func_id_name(func_id), func_id);
+		verbose(env, "unknown return type %u of func %s#%d\n",
+			base_type(ret_type), func_id_name(func_id), func_id);
 		return -EINVAL;
 	}
 
-	if (reg_type_may_be_null(regs[BPF_REG_0].type))
+	if (type_may_be_null(regs[BPF_REG_0].type))
 		regs[BPF_REG_0].id = ++env->id_gen;
 
 	if (is_ptr_cast_function(func_id)) {
@@ -6597,25 +6939,25 @@
 
 	if (known && (val >= BPF_MAX_VAR_OFF || val <= -BPF_MAX_VAR_OFF)) {
 		verbose(env, "math between %s pointer and %lld is not allowed\n",
-			reg_type_str[type], val);
+			reg_type_str(env, type), val);
 		return false;
 	}
 
 	if (reg->off >= BPF_MAX_VAR_OFF || reg->off <= -BPF_MAX_VAR_OFF) {
 		verbose(env, "%s pointer offset %d is not allowed\n",
-			reg_type_str[type], reg->off);
+			reg_type_str(env, type), reg->off);
 		return false;
 	}
 
 	if (smin == S64_MIN) {
 		verbose(env, "math between %s pointer and register with unbounded min value is not allowed\n",
-			reg_type_str[type]);
+			reg_type_str(env, type));
 		return false;
 	}
 
 	if (smin >= BPF_MAX_VAR_OFF || smin <= -BPF_MAX_VAR_OFF) {
 		verbose(env, "value %lld makes %s pointer be out of bounds\n",
-			smin, reg_type_str[type]);
+			smin, reg_type_str(env, type));
 		return false;
 	}
 
@@ -6818,7 +7160,7 @@
 	 */
 	if (!ptr_is_dst_reg) {
 		tmp = *dst_reg;
-		*dst_reg = *ptr_reg;
+		copy_register_state(dst_reg, ptr_reg);
 	}
 	ret = sanitize_speculative_path(env, NULL, env->insn_idx + 1,
 					env->insn_idx);
@@ -6992,11 +7334,17 @@
 		return -EACCES;
 	}
 
-	switch (ptr_reg->type) {
-	case PTR_TO_MAP_VALUE_OR_NULL:
+	if (ptr_reg->type & PTR_MAYBE_NULL) {
 		verbose(env, "R%d pointer arithmetic on %s prohibited, null-check it first\n",
-			dst, reg_type_str[ptr_reg->type]);
+			dst, reg_type_str(env, ptr_reg->type));
 		return -EACCES;
+	}
+
+	switch (base_type(ptr_reg->type)) {
+	case PTR_TO_FLOW_KEYS:
+		if (known)
+			break;
+		fallthrough;
 	case CONST_PTR_TO_MAP:
 		/* smin_val represents the known value */
 		if (known && smin_val == 0 && opcode == BPF_ADD)
@@ -7004,16 +7352,16 @@
 		fallthrough;
 	case PTR_TO_PACKET_END:
 	case PTR_TO_SOCKET:
-	case PTR_TO_SOCKET_OR_NULL:
 	case PTR_TO_SOCK_COMMON:
-	case PTR_TO_SOCK_COMMON_OR_NULL:
 	case PTR_TO_TCP_SOCK:
-	case PTR_TO_TCP_SOCK_OR_NULL:
 	case PTR_TO_XDP_SOCK:
+reject:
 		verbose(env, "R%d pointer arithmetic on %s prohibited\n",
-			dst, reg_type_str[ptr_reg->type]);
+			dst, reg_type_str(env, ptr_reg->type));
 		return -EACCES;
 	default:
+		if (type_may_be_null(ptr_reg->type))
+			goto reject;
 		break;
 	}
 
@@ -7164,11 +7512,7 @@
 
 	if (!check_reg_sane_offset(env, dst_reg, ptr_reg->type))
 		return -EINVAL;
-
-	__update_reg_bounds(dst_reg);
-	__reg_deduce_bounds(dst_reg);
-	__reg_bound_offset(dst_reg);
-
+	reg_bounds_sync(dst_reg);
 	if (sanitize_check_bounds(env, insn, dst_reg) < 0)
 		return -EACCES;
 	if (sanitize_needed(opcode)) {
@@ -7906,10 +8250,7 @@
 	/* ALU32 ops are zero extended into 64bit register */
 	if (alu32)
 		zext_32_to_64(dst_reg);
-
-	__update_reg_bounds(dst_reg);
-	__reg_deduce_bounds(dst_reg);
-	__reg_bound_offset(dst_reg);
+	reg_bounds_sync(dst_reg);
 	return 0;
 }
 
@@ -7969,6 +8310,11 @@
 				return err;
 			return adjust_ptr_min_max_vals(env, insn,
 						       dst_reg, src_reg);
+		} else if (dst_reg->precise) {
+			/* if dst_reg is precise, src_reg should be precise as well */
+			err = mark_chain_precision(env, insn->src_reg);
+			if (err)
+				return err;
 		}
 	} else {
 		/* Pretend the src is a reg with a known value, since we only
@@ -8074,7 +8420,7 @@
 					 * to propagate min/max range.
 					 */
 					src_reg->id = ++env->id_gen;
-				*dst_reg = *src_reg;
+				copy_register_state(dst_reg, src_reg);
 				dst_reg->live |= REG_LIVE_WRITTEN;
 				dst_reg->subreg_def = DEF_NOT_SUBREG;
 			} else {
@@ -8085,7 +8431,7 @@
 						insn->src_reg);
 					return -EACCES;
 				} else if (src_reg->type == SCALAR_VALUE) {
-					*dst_reg = *src_reg;
+					copy_register_state(dst_reg, src_reg);
 					/* Make sure ID is cleared otherwise
 					 * dst_reg min/max could be incorrectly
 					 * propagated into src_reg by find_equal_scalars()
@@ -8098,6 +8444,7 @@
 							 insn->dst_reg);
 				}
 				zext_32_to_64(dst_reg);
+				reg_bounds_sync(dst_reg);
 			}
 		} else {
 			/* case: R = imm
@@ -8169,34 +8516,14 @@
 	return 0;
 }
 
-static void __find_good_pkt_pointers(struct bpf_func_state *state,
-				     struct bpf_reg_state *dst_reg,
-				     enum bpf_reg_type type, int new_range)
-{
-	struct bpf_reg_state *reg;
-	int i;
-
-	for (i = 0; i < MAX_BPF_REG; i++) {
-		reg = &state->regs[i];
-		if (reg->type == type && reg->id == dst_reg->id)
-			/* keep the maximum range already checked */
-			reg->range = max(reg->range, new_range);
-	}
-
-	bpf_for_each_spilled_reg(i, state, reg) {
-		if (!reg)
-			continue;
-		if (reg->type == type && reg->id == dst_reg->id)
-			reg->range = max(reg->range, new_range);
-	}
-}
-
 static void find_good_pkt_pointers(struct bpf_verifier_state *vstate,
 				   struct bpf_reg_state *dst_reg,
 				   enum bpf_reg_type type,
 				   bool range_right_open)
 {
-	int new_range, i;
+	struct bpf_func_state *state;
+	struct bpf_reg_state *reg;
+	int new_range;
 
 	if (dst_reg->off < 0 ||
 	    (dst_reg->off == 0 && range_right_open))
@@ -8212,7 +8539,7 @@
 
 	new_range = dst_reg->off;
 	if (range_right_open)
-		new_range--;
+		new_range++;
 
 	/* Examples for register markings:
 	 *
@@ -8261,9 +8588,11 @@
 	 * the range won't allow anything.
 	 * dst_reg->off is known < MAX_PACKET_OFF, therefore it fits in a u16.
 	 */
-	for (i = 0; i <= vstate->curframe; i++)
-		__find_good_pkt_pointers(vstate->frame[i], dst_reg, type,
-					 new_range);
+	bpf_for_each_reg_in_vstate(vstate, state, reg, ({
+		if (reg->type == type && reg->id == dst_reg->id)
+			/* keep the maximum range already checked */
+			reg->range = max(reg->range, new_range);
+	}));
 }
 
 static int is_branch32_taken(struct bpf_reg_state *reg, u32 val, u8 opcode)
@@ -8535,26 +8864,33 @@
 		return;
 
 	switch (opcode) {
+	/* JEQ/JNE comparison doesn't change the register equivalence.
+	 *
+	 * r1 = r2;
+	 * if (r1 == 42) goto label;
+	 * ...
+	 * label: // here both r1 and r2 are known to be 42.
+	 *
+	 * Hence when marking register as known preserve it's ID.
+	 */
 	case BPF_JEQ:
+		if (is_jmp32) {
+			__mark_reg32_known(true_reg, val32);
+			true_32off = tnum_subreg(true_reg->var_off);
+		} else {
+			___mark_reg_known(true_reg, val);
+			true_64off = true_reg->var_off;
+		}
+		break;
 	case BPF_JNE:
-	{
-		struct bpf_reg_state *reg =
-			opcode == BPF_JEQ ? true_reg : false_reg;
-
-		/* JEQ/JNE comparison doesn't change the register equivalence.
-		 * r1 = r2;
-		 * if (r1 == 42) goto label;
-		 * ...
-		 * label: // here both r1 and r2 are known to be 42.
-		 *
-		 * Hence when marking register as known preserve it's ID.
-		 */
-		if (is_jmp32)
-			__mark_reg32_known(reg, val32);
-		else
-			___mark_reg_known(reg, val);
+		if (is_jmp32) {
+			__mark_reg32_known(false_reg, val32);
+			false_32off = tnum_subreg(false_reg->var_off);
+		} else {
+			___mark_reg_known(false_reg, val);
+			false_64off = false_reg->var_off;
+		}
 		break;
-	}
 	case BPF_JSET:
 		if (is_jmp32) {
 			false_32off = tnum_and(false_32off, tnum_const(~val32));
@@ -8693,21 +9029,8 @@
 							dst_reg->smax_value);
 	src_reg->var_off = dst_reg->var_off = tnum_intersect(src_reg->var_off,
 							     dst_reg->var_off);
-	/* We might have learned new bounds from the var_off. */
-	__update_reg_bounds(src_reg);
-	__update_reg_bounds(dst_reg);
-	/* We might have learned something about the sign bit. */
-	__reg_deduce_bounds(src_reg);
-	__reg_deduce_bounds(dst_reg);
-	/* We might have learned some bits from the bounds. */
-	__reg_bound_offset(src_reg);
-	__reg_bound_offset(dst_reg);
-	/* Intersecting with the old var_off might have improved our bounds
-	 * slightly.  e.g. if umax was 0x7f...f and var_off was (0; 0xf...fc),
-	 * then new var_off is (0; 0x7f...fc) which improves our umax.
-	 */
-	__update_reg_bounds(src_reg);
-	__update_reg_bounds(dst_reg);
+	reg_bounds_sync(src_reg);
+	reg_bounds_sync(dst_reg);
 }
 
 static void reg_combine_min_max(struct bpf_reg_state *true_src,
@@ -8730,17 +9053,17 @@
 				 struct bpf_reg_state *reg, u32 id,
 				 bool is_null)
 {
-	if (reg_type_may_be_null(reg->type) && reg->id == id &&
+	if (type_may_be_null(reg->type) && reg->id == id &&
 	    !WARN_ON_ONCE(!reg->id)) {
-		/* Old offset (both fixed and variable parts) should
-		 * have been known-zero, because we don't allow pointer
-		 * arithmetic on pointers that might be NULL.
-		 */
 		if (WARN_ON_ONCE(reg->smin_value || reg->smax_value ||
 				 !tnum_equals_const(reg->var_off, 0) ||
 				 reg->off)) {
-			__mark_reg_known_zero(reg);
-			reg->off = 0;
+			/* Old offset (both fixed and variable parts) should
+			 * have been known-zero, because we don't allow pointer
+			 * arithmetic on pointers that might be NULL. If we
+			 * see this happening, don't convert the register.
+			 */
+			return;
 		}
 		if (is_null) {
 			reg->type = SCALAR_VALUE;
@@ -8758,7 +9081,7 @@
 
 		if (!reg_may_point_to_spin_lock(reg)) {
 			/* For not-NULL ptr, reg->ref_obj_id will be reset
-			 * in release_reg_references().
+			 * in release_reference().
 			 *
 			 * reg->id is still used by spin_lock ptr. Other
 			 * than spin_lock ptr type, reg->id can be reset.
@@ -8768,22 +9091,6 @@
 	}
 }
 
-static void __mark_ptr_or_null_regs(struct bpf_func_state *state, u32 id,
-				    bool is_null)
-{
-	struct bpf_reg_state *reg;
-	int i;
-
-	for (i = 0; i < MAX_BPF_REG; i++)
-		mark_ptr_or_null_reg(state, &state->regs[i], id, is_null);
-
-	bpf_for_each_spilled_reg(i, state, reg) {
-		if (!reg)
-			continue;
-		mark_ptr_or_null_reg(state, reg, id, is_null);
-	}
-}
-
 /* The logic is similar to find_good_pkt_pointers(), both could eventually
  * be folded together at some point.
  */
@@ -8791,10 +9098,9 @@
 				  bool is_null)
 {
 	struct bpf_func_state *state = vstate->frame[vstate->curframe];
-	struct bpf_reg_state *regs = state->regs;
+	struct bpf_reg_state *regs = state->regs, *reg;
 	u32 ref_obj_id = regs[regno].ref_obj_id;
 	u32 id = regs[regno].id;
-	int i;
 
 	if (ref_obj_id && ref_obj_id == id && is_null)
 		/* regs[regno] is in the " == NULL" branch.
@@ -8803,8 +9109,9 @@
 		 */
 		WARN_ON_ONCE(release_reference_state(state, id));
 
-	for (i = 0; i <= vstate->curframe; i++)
-		__mark_ptr_or_null_regs(vstate->frame[i], id, is_null);
+	bpf_for_each_reg_in_vstate(vstate, state, reg, ({
+		mark_ptr_or_null_reg(state, reg, id, is_null);
+	}));
 }
 
 static bool try_match_pkt_pointers(const struct bpf_insn *insn,
@@ -8917,23 +9224,14 @@
 {
 	struct bpf_func_state *state;
 	struct bpf_reg_state *reg;
-	int i, j;
 
-	for (i = 0; i <= vstate->curframe; i++) {
-		state = vstate->frame[i];
-		for (j = 0; j < MAX_BPF_REG; j++) {
-			reg = &state->regs[j];
-			if (reg->type == SCALAR_VALUE && reg->id == known_reg->id)
-				*reg = *known_reg;
+	bpf_for_each_reg_in_vstate(vstate, state, reg, ({
+		if (reg->type == SCALAR_VALUE && reg->id == known_reg->id) {
+			s32 saved_subreg_def = reg->subreg_def;
+			copy_register_state(reg, known_reg);
+			reg->subreg_def = saved_subreg_def;
 		}
-
-		bpf_for_each_spilled_reg(j, state, reg) {
-			if (!reg)
-				continue;
-			if (reg->type == SCALAR_VALUE && reg->id == known_reg->id)
-				*reg = *known_reg;
-		}
-	}
+	}));
 }
 
 static int check_cond_jmp_op(struct bpf_verifier_env *env,
@@ -9108,7 +9406,7 @@
 	 */
 	if (!is_jmp32 && BPF_SRC(insn->code) == BPF_K &&
 	    insn->imm == 0 && (opcode == BPF_JEQ || opcode == BPF_JNE) &&
-	    reg_type_may_be_null(dst_reg->type)) {
+	    type_may_be_null(dst_reg->type)) {
 		/* Mark all identical registers in each branch as either
 		 * safe or unknown depending R == 0 or R != 0 conditional.
 		 */
@@ -9159,11 +9457,15 @@
 		return 0;
 	}
 
-	if (insn->src_reg == BPF_PSEUDO_BTF_ID) {
-		mark_reg_known_zero(env, regs, insn->dst_reg);
+	/* All special src_reg cases are listed below. From this point onwards
+	 * we either succeed and assign a corresponding dst_reg->type after
+	 * zeroing the offset, or fail and reject the program.
+	 */
+	mark_reg_known_zero(env, regs, insn->dst_reg);
 
+	if (insn->src_reg == BPF_PSEUDO_BTF_ID) {
 		dst_reg->type = aux->btf_var.reg_type;
-		switch (dst_reg->type) {
+		switch (base_type(dst_reg->type)) {
 		case PTR_TO_MEM:
 			dst_reg->mem_size = aux->btf_var.mem_size;
 			break;
@@ -9181,7 +9483,8 @@
 
 	if (insn->src_reg == BPF_PSEUDO_FUNC) {
 		struct bpf_prog_aux *aux = env->prog->aux;
-		u32 subprogno = insn[1].imm;
+		u32 subprogno = find_subprog(env,
+					     env->insn_idx + insn->imm + 1);
 
 		if (!aux->func_info) {
 			verbose(env, "missing btf func_info\n");
@@ -9198,7 +9501,6 @@
 	}
 
 	map = env->used_maps[aux->map_index];
-	mark_reg_known_zero(env, regs, insn->dst_reg);
 	dst_reg->map_ptr = map;
 
 	if (insn->src_reg == BPF_PSEUDO_MAP_VALUE ||
@@ -9302,7 +9604,7 @@
 			return err;
 	}
 
-	err = check_ctx_reg(env, &regs[ctx_reg], ctx_reg);
+	err = check_ptr_off_reg(env, &regs[ctx_reg], ctx_reg);
 	if (err < 0)
 		return err;
 
@@ -9327,7 +9629,7 @@
 	struct tnum enforce_attach_type_range = tnum_unknown;
 	const struct bpf_prog *prog = env->prog;
 	struct bpf_reg_state *reg;
-	struct tnum range = tnum_range(0, 1);
+	struct tnum range = tnum_range(0, 1), const_0 = tnum_const(0);
 	enum bpf_prog_type prog_type = resolve_prog_type(env->prog);
 	int err;
 	struct bpf_func_state *frame = env->cur_state->frame[0];
@@ -9361,12 +9663,12 @@
 		/* enforce return zero from async callbacks like timer */
 		if (reg->type != SCALAR_VALUE) {
 			verbose(env, "In async callback the register R0 is not a known value (%s)\n",
-				reg_type_str[reg->type]);
+				reg_type_str(env, reg->type));
 			return -EINVAL;
 		}
 
-		if (!tnum_in(tnum_const(0), reg->var_off)) {
-			verbose_invalid_scalar(env, reg, &range, "async callback", "R0");
+		if (!tnum_in(const_0, reg->var_off)) {
+			verbose_invalid_scalar(env, reg, &const_0, "async callback", "R0");
 			return -EINVAL;
 		}
 		return 0;
@@ -9375,7 +9677,7 @@
 	if (is_subprog) {
 		if (reg->type != SCALAR_VALUE) {
 			verbose(env, "At subprogram exit the register R0 is not a scalar value (%s)\n",
-				reg_type_str[reg->type]);
+				reg_type_str(env, reg->type));
 			return -EINVAL;
 		}
 		return 0;
@@ -9439,7 +9741,7 @@
 
 	if (reg->type != SCALAR_VALUE) {
 		verbose(env, "At program exit the register R0 is not a known value (%s)\n",
-			reg_type_str[reg->type]);
+			reg_type_str(env, reg->type));
 		return -EINVAL;
 	}
 
@@ -10220,12 +10522,12 @@
 		return true;
 	if (rcur->type == NOT_INIT)
 		return false;
-	switch (rold->type) {
+	switch (base_type(rold->type)) {
 	case SCALAR_VALUE:
 		if (env->explore_alu_limits)
 			return false;
 		if (rcur->type == SCALAR_VALUE) {
-			if (!rold->precise && !rcur->precise)
+			if (!rold->precise)
 				return true;
 			/* new val must satisfy old val knowledge */
 			return range_within(rold, rcur) &&
@@ -10242,6 +10544,22 @@
 		}
 	case PTR_TO_MAP_KEY:
 	case PTR_TO_MAP_VALUE:
+		/* a PTR_TO_MAP_VALUE could be safe to use as a
+		 * PTR_TO_MAP_VALUE_OR_NULL into the same map.
+		 * However, if the old PTR_TO_MAP_VALUE_OR_NULL then got NULL-
+		 * checked, doing so could have affected others with the same
+		 * id, and we can't check for that because we lost the id when
+		 * we converted to a PTR_TO_MAP_VALUE.
+		 */
+		if (type_may_be_null(rold->type)) {
+			if (!type_may_be_null(rcur->type))
+				return false;
+			if (memcmp(rold, rcur, offsetof(struct bpf_reg_state, id)))
+				return false;
+			/* Check our ids match any regs they're supposed to */
+			return check_ids(rold->id, rcur->id, idmap);
+		}
+
 		/* If the new min/max/var_off satisfy the old ones and
 		 * everything else matches, we are OK.
 		 * 'id' is not compared, since it's only used for maps with
@@ -10253,20 +10571,6 @@
 		return memcmp(rold, rcur, offsetof(struct bpf_reg_state, id)) == 0 &&
 		       range_within(rold, rcur) &&
 		       tnum_in(rold->var_off, rcur->var_off);
-	case PTR_TO_MAP_VALUE_OR_NULL:
-		/* a PTR_TO_MAP_VALUE could be safe to use as a
-		 * PTR_TO_MAP_VALUE_OR_NULL into the same map.
-		 * However, if the old PTR_TO_MAP_VALUE_OR_NULL then got NULL-
-		 * checked, doing so could have affected others with the same
-		 * id, and we can't check for that because we lost the id when
-		 * we converted to a PTR_TO_MAP_VALUE.
-		 */
-		if (rcur->type != PTR_TO_MAP_VALUE_OR_NULL)
-			return false;
-		if (memcmp(rold, rcur, offsetof(struct bpf_reg_state, id)))
-			return false;
-		/* Check our ids match any regs they're supposed to */
-		return check_ids(rold->id, rcur->id, idmap);
 	case PTR_TO_PACKET_META:
 	case PTR_TO_PACKET:
 		if (rcur->type != rold->type)
@@ -10295,11 +10599,8 @@
 	case PTR_TO_PACKET_END:
 	case PTR_TO_FLOW_KEYS:
 	case PTR_TO_SOCKET:
-	case PTR_TO_SOCKET_OR_NULL:
 	case PTR_TO_SOCK_COMMON:
-	case PTR_TO_SOCK_COMMON_OR_NULL:
 	case PTR_TO_TCP_SOCK:
-	case PTR_TO_TCP_SOCK_OR_NULL:
 	case PTR_TO_XDP_SOCK:
 		/* Only valid matches are exact, which memcmp() above
 		 * would have accepted
@@ -10356,9 +10657,9 @@
 			 * return false to continue verification of this path
 			 */
 			return false;
-		if (i % BPF_REG_SIZE)
+		if (i % BPF_REG_SIZE != BPF_REG_SIZE - 1)
 			continue;
-		if (old->stack[spi].slot_type[0] != STACK_SPILL)
+		if (!is_spilled_reg(&old->stack[spi]))
 			continue;
 		if (!regsafe(env, &old->stack[spi].spilled_ptr,
 			     &cur->stack[spi].spilled_ptr, idmap))
@@ -10549,34 +10850,38 @@
 {
 	struct bpf_reg_state *state_reg;
 	struct bpf_func_state *state;
-	int i, err = 0;
+	int i, err = 0, fr;
 
-	state = old->frame[old->curframe];
-	state_reg = state->regs;
-	for (i = 0; i < BPF_REG_FP; i++, state_reg++) {
-		if (state_reg->type != SCALAR_VALUE ||
-		    !state_reg->precise)
-			continue;
-		if (env->log.level & BPF_LOG_LEVEL2)
-			verbose(env, "propagating r%d\n", i);
-		err = mark_chain_precision(env, i);
-		if (err < 0)
-			return err;
-	}
+	for (fr = old->curframe; fr >= 0; fr--) {
+		state = old->frame[fr];
+		state_reg = state->regs;
+		for (i = 0; i < BPF_REG_FP; i++, state_reg++) {
+			if (state_reg->type != SCALAR_VALUE ||
+			    !state_reg->precise ||
+			    !(state_reg->live & REG_LIVE_READ))
+				continue;
+			if (env->log.level & BPF_LOG_LEVEL2)
+				verbose(env, "frame %d: propagating r%d\n", fr, i);
+			err = mark_chain_precision_frame(env, fr, i);
+			if (err < 0)
+				return err;
+		}
 
-	for (i = 0; i < state->allocated_stack / BPF_REG_SIZE; i++) {
-		if (state->stack[i].slot_type[0] != STACK_SPILL)
-			continue;
-		state_reg = &state->stack[i].spilled_ptr;
-		if (state_reg->type != SCALAR_VALUE ||
-		    !state_reg->precise)
-			continue;
-		if (env->log.level & BPF_LOG_LEVEL2)
-			verbose(env, "propagating fp%d\n",
-				(-i - 1) * BPF_REG_SIZE);
-		err = mark_chain_precision_stack(env, i);
-		if (err < 0)
-			return err;
+		for (i = 0; i < state->allocated_stack / BPF_REG_SIZE; i++) {
+			if (!is_spilled_reg(&state->stack[i]))
+				continue;
+			state_reg = &state->stack[i].spilled_ptr;
+			if (state_reg->type != SCALAR_VALUE ||
+			    !state_reg->precise ||
+			    !(state_reg->live & REG_LIVE_READ))
+				continue;
+			if (env->log.level & BPF_LOG_LEVEL2)
+				verbose(env, "frame %d: propagating fp%d\n",
+					fr, (-i - 1) * BPF_REG_SIZE);
+			err = mark_chain_precision_stack_frame(env, fr, i);
+			if (err < 0)
+				return err;
+		}
 	}
 	return 0;
 }
@@ -10771,6 +11076,10 @@
 	env->prev_jmps_processed = env->jmps_processed;
 	env->prev_insn_processed = env->insn_processed;
 
+	/* forget precise markings we inherited, see __mark_chain_precision */
+	if (env->bpf_capable)
+		mark_all_scalars_imprecise(env, cur);
+
 	/* add new state to the head of linked list */
 	new = &new_sl->state;
 	err = copy_verifier_state(new, cur);
@@ -10825,17 +11134,13 @@
 /* Return true if it's OK to have the same insn return a different type. */
 static bool reg_type_mismatch_ok(enum bpf_reg_type type)
 {
-	switch (type) {
+	switch (base_type(type)) {
 	case PTR_TO_CTX:
 	case PTR_TO_SOCKET:
-	case PTR_TO_SOCKET_OR_NULL:
 	case PTR_TO_SOCK_COMMON:
-	case PTR_TO_SOCK_COMMON_OR_NULL:
 	case PTR_TO_TCP_SOCK:
-	case PTR_TO_TCP_SOCK_OR_NULL:
 	case PTR_TO_XDP_SOCK:
 	case PTR_TO_BTF_ID:
-	case PTR_TO_BTF_ID_OR_NULL:
 		return false;
 	default:
 		return true;
@@ -11059,7 +11364,7 @@
 			if (is_ctx_reg(env, insn->dst_reg)) {
 				verbose(env, "BPF_ST stores into R%d %s is not allowed\n",
 					insn->dst_reg,
-					reg_type_str[reg_state(env, insn->dst_reg)->type]);
+					reg_type_str(env, reg_state(env, insn->dst_reg)->type));
 				return -EACCES;
 			}
 
@@ -11128,6 +11433,16 @@
 					return -EINVAL;
 				}
 
+				/* We must do check_reference_leak here before
+				 * prepare_func_exit to handle the case when
+				 * state->curframe > 0, it may be a callback
+				 * function, for which reference_state must
+				 * match caller reference state when it exits.
+				 */
+				err = check_reference_leak(env);
+				if (err)
+					return err;
+
 				if (state->curframe) {
 					/* exit from nested function */
 					err = prepare_func_exit(env, &env->insn_idx);
@@ -11137,10 +11452,6 @@
 					continue;
 				}
 
-				err = check_reference_leak(env);
-				if (err)
-					return err;
-
 				err = check_return_code(env);
 				if (err)
 					return err;
@@ -11310,7 +11621,7 @@
 			err = -EINVAL;
 			goto err_put;
 		}
-		aux->btf_var.reg_type = PTR_TO_MEM;
+		aux->btf_var.reg_type = PTR_TO_MEM | MEM_RDONLY;
 		aux->btf_var.mem_size = tsize;
 	} else {
 		aux->btf_var.reg_type = PTR_TO_BTF_ID;
@@ -11435,6 +11746,13 @@
 		}
 	}
 
+	if (map_value_has_timer(map)) {
+		if (is_tracing_prog_type(prog_type)) {
+			verbose(env, "tracing progs cannot use bpf_timer yet\n");
+			return -EINVAL;
+		}
+	}
+
 	if ((bpf_prog_is_dev_bound(prog->aux) || bpf_map_is_dev_bound(map)) &&
 	    !bpf_offload_prog_map_match(prog, map)) {
 		verbose(env, "offload device mismatch between prog and map\n");
@@ -11572,8 +11890,7 @@
 			f = fdget(fd);
 			map = __bpf_map_get(f);
 			if (IS_ERR(map)) {
-				verbose(env, "fd %d is not pointing to valid bpf_map\n",
-					insn[0].imm);
+				verbose(env, "fd %d is not pointing to valid bpf_map\n", fd);
 				return PTR_ERR(map);
 			}
 
@@ -12122,6 +12439,10 @@
 		if (!bpf_jit_needs_zext() && !is_cmpxchg_insn(&insn))
 			continue;
 
+		/* Zero-extension is done by the caller. */
+		if (bpf_pseudo_kfunc_call(&insn))
+			continue;
+
 		if (WARN_ON(load_reg == -1)) {
 			verbose(env, "verifier bug. zext_dst is set, but no reg is defined\n");
 			return -EFAULT;
@@ -12318,7 +12639,7 @@
 					insn_buf[cnt++] = BPF_ALU64_IMM(BPF_RSH,
 									insn->dst_reg,
 									shift);
-				insn_buf[cnt++] = BPF_ALU64_IMM(BPF_AND, insn->dst_reg,
+				insn_buf[cnt++] = BPF_ALU32_IMM(BPF_AND, insn->dst_reg,
 								(1ULL << size * 8) - 1);
 			}
 		}
@@ -12350,14 +12671,9 @@
 		return 0;
 
 	for (i = 0, insn = prog->insnsi; i < prog->len; i++, insn++) {
-		if (bpf_pseudo_func(insn)) {
-			env->insn_aux_data[i].call_imm = insn->imm;
-			/* subprog is encoded in insn[1].imm */
+		if (!bpf_pseudo_func(insn) && !bpf_pseudo_call(insn))
 			continue;
-		}
 
-		if (!bpf_pseudo_call(insn))
-			continue;
 		/* Upon error here we cannot fall back to interpreter but
 		 * need a hard reject of the program. Thus -EFAULT is
 		 * propagated in any case.
@@ -12378,6 +12694,12 @@
 		env->insn_aux_data[i].call_imm = insn->imm;
 		/* point imm to __bpf_call_base+1 from JITs point of view */
 		insn->imm = 1;
+		if (bpf_pseudo_func(insn))
+			/* jit (e.g. x86_64) may emit fewer instructions
+			 * if it learns a u32 imm is the same as a u64 imm.
+			 * Force a non zero here.
+			 */
+			insn[1].imm = 1;
 	}
 
 	err = bpf_prog_alloc_jited_linfo(prog);
@@ -12413,6 +12735,7 @@
 		/* Below members will be freed only at prog->aux */
 		func[i]->aux->btf = prog->aux->btf;
 		func[i]->aux->func_info = prog->aux->func_info;
+		func[i]->aux->func_info_cnt = prog->aux->func_info_cnt;
 		func[i]->aux->poke_tab = prog->aux->poke_tab;
 		func[i]->aux->size_poke_tab = prog->aux->size_poke_tab;
 
@@ -12425,9 +12748,6 @@
 				poke->aux = func[i]->aux;
 		}
 
-		/* Use bpf_prog_F_tag to indicate functions in stack traces.
-		 * Long term would need debug info to populate names
-		 */
 		func[i]->aux->name[0] = 'F';
 		func[i]->aux->stack_depth = env->subprog_info[i].stack_depth;
 		func[i]->jit_requested = 1;
@@ -12461,7 +12781,7 @@
 		insn = func[i]->insnsi;
 		for (j = 0; j < func[i]->len; j++, insn++) {
 			if (bpf_pseudo_func(insn)) {
-				subprog = insn[1].imm;
+				subprog = insn->off;
 				insn[0].imm = (u32)(long)func[subprog]->bpf_func;
 				insn[1].imm = ((u64)(long)func[subprog]->bpf_func) >> 32;
 				continue;
@@ -12499,13 +12819,18 @@
 	}
 
 	/* finally lock prog and jit images for all functions and
-	 * populate kallsysm
+	 * populate kallsysm. Begin at the first subprogram, since
+	 * bpf_prog_load will add the kallsyms for the main program.
 	 */
-	for (i = 0; i < env->subprog_cnt; i++) {
-		bpf_prog_lock_ro(func[i]);
-		bpf_prog_kallsyms_add(func[i]);
+	for (i = 1; i < env->subprog_cnt; i++) {
+		err = bpf_prog_lock_ro(func[i]);
+		if (err)
+			goto out_free;
 	}
 
+	for (i = 1; i < env->subprog_cnt; i++)
+		bpf_prog_kallsyms_add(func[i]);
+
 	/* Last step: make now unused interpreter insns from main
 	 * prog consistent for later dump requests, so they can
 	 * later look the same as if they were interpreted only.
@@ -12513,7 +12838,8 @@
 	for (i = 0, insn = prog->insnsi; i < prog->len; i++, insn++) {
 		if (bpf_pseudo_func(insn)) {
 			insn[0].imm = env->insn_aux_data[i].call_imm;
-			insn[1].imm = find_subprog(env, i + insn[0].imm + 1);
+			insn[1].imm = insn->off;
+			insn->off = 0;
 			continue;
 		}
 		if (!bpf_pseudo_call(insn))
@@ -12525,6 +12851,8 @@
 
 	prog->jited = 1;
 	prog->bpf_func = func[0]->bpf_func;
+	prog->aux->extable = func[0]->aux->extable;
+	prog->aux->num_exentries = func[0]->aux->num_exentries;
 	prog->aux->func = func;
 	prog->aux->func_cnt = env->subprog_cnt;
 	bpf_prog_jit_attempt_done(prog);
@@ -13114,6 +13442,8 @@
 			BPF_MAIN_FUNC /* callsite */,
 			0 /* frameno */,
 			subprog);
+	state->first_insn_idx = env->subprog_info[subprog].start;
+	state->last_insn_idx = -1;
 
 	regs = state->frame[state->curframe]->regs;
 	if (subprog || env->prog->type == BPF_PROG_TYPE_EXT) {
@@ -13125,7 +13455,7 @@
 				mark_reg_known_zero(env, regs, i);
 			else if (regs[i].type == SCALAR_VALUE)
 				mark_reg_unknown(env, regs, i);
-			else if (regs[i].type == PTR_TO_MEM_OR_NULL) {
+			else if (base_type(regs[i].type) == PTR_TO_MEM) {
 				const u32 mem_size = regs[i].mem_size;
 
 				mark_reg_known_zero(env, regs, i);
@@ -13572,6 +13902,10 @@
 #if !defined CONFIG_PREEMPT_RCU && !defined CONFIG_TINY_RCU
 BTF_ID(func, rcu_read_unlock_strict)
 #endif
+#if defined(CONFIG_DEBUG_PREEMPT) || defined(CONFIG_TRACE_PREEMPT_TOGGLE)
+BTF_ID(func, preempt_count_add)
+BTF_ID(func, preempt_count_sub)
+#endif
 BTF_SET_END(btf_id_deny)
 
 static int check_attach_btf_id(struct bpf_verifier_env *env)
@@ -13681,7 +14015,7 @@
 	/* 'struct bpf_verifier_env' can be global, but since it's not small,
 	 * allocate/free it every time bpf_check() is called
 	 */
-	env = kzalloc(sizeof(struct bpf_verifier_env), GFP_KERNEL);
+	env = kvzalloc(sizeof(struct bpf_verifier_env), GFP_KERNEL);
 	if (!env)
 		return -ENOMEM;
 	log = &env->log;
@@ -13713,11 +14047,11 @@
 		log->ubuf = (char __user *) (unsigned long) attr->log_buf;
 		log->len_total = attr->log_size;
 
-		ret = -EINVAL;
 		/* log attributes have to be sane */
-		if (log->len_total < 128 || log->len_total > UINT_MAX >> 2 ||
-		    !log->level || !log->ubuf || log->level & ~BPF_LOG_MASK)
+		if (!bpf_verifier_log_attr_valid(log)) {
+			ret = -EINVAL;
 			goto err_unlock;
+		}
 	}
 
 	if (IS_ERR(btf_vmlinux)) {
@@ -13896,6 +14230,6 @@
 		mutex_unlock(&bpf_verifier_lock);
 	vfree(env->insn_aux_data);
 err_free_env:
-	kfree(env);
+	kvfree(env);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cfi.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cfi.c
@@ -281,6 +281,8 @@
 static inline cfi_check_fn find_check_fn(unsigned long ptr)
 {
 	cfi_check_fn fn = NULL;
+	unsigned long flags;
+	bool rcu_idle;
 
 	if (is_kernel_text(ptr))
 		return __cfi_check;
@@ -290,13 +292,21 @@
 	 * the shadow and __module_address use RCU, so we need to wake it
 	 * up if necessary.
 	 */
-	RCU_NONIDLE({
-		if (IS_ENABLED(CONFIG_CFI_CLANG_SHADOW))
-			fn = find_shadow_check_fn(ptr);
+	rcu_idle = !rcu_is_watching();
+	if (rcu_idle) {
+		local_irq_save(flags);
+		rcu_irq_enter();
+	}
 
-		if (!fn)
-			fn = find_module_check_fn(ptr);
-	});
+	if (IS_ENABLED(CONFIG_CFI_CLANG_SHADOW))
+		fn = find_shadow_check_fn(ptr);
+	if (!fn)
+		fn = find_module_check_fn(ptr);
+
+	if (rcu_idle) {
+		rcu_irq_exit();
+		local_irq_restore(flags);
+	}
 
 	return fn;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cgroup/cgroup-internal.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/cgroup/cgroup-internal.h
@@ -65,6 +65,25 @@
 	return container_of(kfc, struct cgroup_fs_context, kfc);
 }
 
+struct cgroup_pidlist;
+
+struct cgroup_file_ctx {
+	struct cgroup_namespace	*ns;
+
+	struct {
+		void			*trigger;
+	} psi;
+
+	struct {
+		bool			started;
+		struct css_task_iter	iter;
+	} procs;
+
+	struct {
+		struct cgroup_pidlist	*pidlist;
+	} procs1;
+};
+
 /*
  * A cgroup can be associated with multiple css_sets as different tasks may
  * belong to different cgroups on different hierarchies.  In the other
@@ -150,11 +169,11 @@
 extern spinlock_t css_set_lock;
 extern struct cgroup_subsys *cgroup_subsys[];
 extern struct list_head cgroup_roots;
-extern struct file_system_type cgroup_fs_type;
 
 /* iterate across the hierarchies */
 #define for_each_root(root)						\
-	list_for_each_entry((root), &cgroup_roots, root_list)
+	list_for_each_entry_rcu((root), &cgroup_roots, root_list,	\
+				lockdep_is_held(&cgroup_mutex))
 
 /**
  * for_each_subsys - iterate all enabled cgroup subsystems
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cgroup/cgroup-v1.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cgroup/cgroup-v1.c
@@ -59,6 +59,7 @@
 	int retval = 0;
 
 	mutex_lock(&cgroup_mutex);
+	cpus_read_lock();
 	percpu_down_write(&cgroup_threadgroup_rwsem);
 	for_each_root(root) {
 		struct cgroup *from_cgrp;
@@ -75,6 +76,7 @@
 			break;
 	}
 	percpu_up_write(&cgroup_threadgroup_rwsem);
+	cpus_read_unlock();
 	mutex_unlock(&cgroup_mutex);
 
 	return retval;
@@ -363,10 +365,9 @@
 	}
 	css_task_iter_end(&it);
 	length = n;
-	/* now sort & (if procs) strip out duplicates */
+	/* now sort & strip out duplicates (tgids or recycled thread PIDs) */
 	sort(array, length, sizeof(pid_t), cmppid, NULL);
-	if (type == CGROUP_FILE_PROCS)
-		length = pidlist_uniq(array, length);
+	length = pidlist_uniq(array, length);
 
 	l = cgroup_pidlist_find_create(cgrp, type);
 	if (!l) {
@@ -397,6 +398,7 @@
 	 * next pid to display, if any
 	 */
 	struct kernfs_open_file *of = s->private;
+	struct cgroup_file_ctx *ctx = of->priv;
 	struct cgroup *cgrp = seq_css(s)->cgroup;
 	struct cgroup_pidlist *l;
 	enum cgroup_filetype type = seq_cft(s)->private;
@@ -406,25 +408,24 @@
 	mutex_lock(&cgrp->pidlist_mutex);
 
 	/*
-	 * !NULL @of->priv indicates that this isn't the first start()
-	 * after open.  If the matching pidlist is around, we can use that.
-	 * Look for it.  Note that @of->priv can't be used directly.  It
-	 * could already have been destroyed.
+	 * !NULL @ctx->procs1.pidlist indicates that this isn't the first
+	 * start() after open. If the matching pidlist is around, we can use
+	 * that. Look for it. Note that @ctx->procs1.pidlist can't be used
+	 * directly. It could already have been destroyed.
 	 */
-	if (of->priv)
-		of->priv = cgroup_pidlist_find(cgrp, type);
+	if (ctx->procs1.pidlist)
+		ctx->procs1.pidlist = cgroup_pidlist_find(cgrp, type);
 
 	/*
 	 * Either this is the first start() after open or the matching
 	 * pidlist has been destroyed inbetween.  Create a new one.
 	 */
-	if (!of->priv) {
-		ret = pidlist_array_load(cgrp, type,
-					 (struct cgroup_pidlist **)&of->priv);
+	if (!ctx->procs1.pidlist) {
+		ret = pidlist_array_load(cgrp, type, &ctx->procs1.pidlist);
 		if (ret)
 			return ERR_PTR(ret);
 	}
-	l = of->priv;
+	l = ctx->procs1.pidlist;
 
 	if (pid) {
 		int end = l->length;
@@ -452,7 +453,8 @@
 static void cgroup_pidlist_stop(struct seq_file *s, void *v)
 {
 	struct kernfs_open_file *of = s->private;
-	struct cgroup_pidlist *l = of->priv;
+	struct cgroup_file_ctx *ctx = of->priv;
+	struct cgroup_pidlist *l = ctx->procs1.pidlist;
 
 	if (l)
 		mod_delayed_work(cgroup_pidlist_destroy_wq, &l->destroy_dwork,
@@ -463,7 +465,8 @@
 static void *cgroup_pidlist_next(struct seq_file *s, void *v, loff_t *pos)
 {
 	struct kernfs_open_file *of = s->private;
-	struct cgroup_pidlist *l = of->priv;
+	struct cgroup_file_ctx *ctx = of->priv;
+	struct cgroup_pidlist *l = ctx->procs1.pidlist;
 	pid_t *p = v;
 	pid_t *end = l->list + l->length;
 	/*
@@ -507,10 +510,11 @@
 		goto out_unlock;
 
 	/*
-	 * Even if we're attaching all tasks in the thread group, we only
-	 * need to check permissions on one of them.
+	 * Even if we're attaching all tasks in the thread group, we only need
+	 * to check permissions on one of them. Check permissions using the
+	 * credentials from file open to protect against inherited fd attacks.
 	 */
-	cred = current_cred();
+	cred = of->file->f_cred;
 	tcred = get_task_cred(task);
 	if (!uid_eq(cred->euid, GLOBAL_ROOT_UID) &&
 	    !uid_eq(cred->euid, tcred->uid) &&
@@ -546,9 +550,19 @@
 					  char *buf, size_t nbytes, loff_t off)
 {
 	struct cgroup *cgrp;
+	struct cgroup_file_ctx *ctx;
 
 	BUILD_BUG_ON(sizeof(cgrp->root->release_agent_path) < PATH_MAX);
 
+	/*
+	 * Release agent gets called with all capabilities,
+	 * require capabilities to set release agent.
+	 */
+	ctx = of->priv;
+	if ((ctx->ns->user_ns != &init_user_ns) ||
+	    !file_ns_capable(of->file, &init_user_ns, CAP_SYS_ADMIN))
+		return -EPERM;
+
 	cgrp = cgroup_kn_lock_live(of->kn, false);
 	if (!cgrp)
 		return -ENODEV;
@@ -960,6 +974,12 @@
 		/* Specifying two release agents is forbidden */
 		if (ctx->release_agent)
 			return invalfc(fc, "release_agent respecified");
+		/*
+		 * Release agent gets called with all capabilities,
+		 * require capabilities to set release agent.
+		 */
+		if ((fc->user_ns != &init_user_ns) || !capable(CAP_SYS_ADMIN))
+			return invalfc(fc, "Setting release_agent not allowed");
 		ctx->release_agent = param->string;
 		param->string = NULL;
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cgroup/cgroup.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cgroup/cgroup.c
@@ -56,6 +56,7 @@
 #include <linux/file.h>
 #include <linux/fs_parser.h>
 #include <linux/sched/cputime.h>
+#include <linux/sched/deadline.h>
 #include <linux/psi.h>
 #include <net/sock.h>
 
@@ -764,7 +765,8 @@
 	.task_iters		= LIST_HEAD_INIT(init_css_set.task_iters),
 	.threaded_csets		= LIST_HEAD_INIT(init_css_set.threaded_csets),
 	.cgrp_links		= LIST_HEAD_INIT(init_css_set.cgrp_links),
-	.mg_preload_node	= LIST_HEAD_INIT(init_css_set.mg_preload_node),
+	.mg_src_preload_node	= LIST_HEAD_INIT(init_css_set.mg_src_preload_node),
+	.mg_dst_preload_node	= LIST_HEAD_INIT(init_css_set.mg_dst_preload_node),
 	.mg_node		= LIST_HEAD_INIT(init_css_set.mg_node),
 
 	/*
@@ -1239,7 +1241,8 @@
 	INIT_LIST_HEAD(&cset->threaded_csets);
 	INIT_HLIST_NODE(&cset->hlist);
 	INIT_LIST_HEAD(&cset->cgrp_links);
-	INIT_LIST_HEAD(&cset->mg_preload_node);
+	INIT_LIST_HEAD(&cset->mg_src_preload_node);
+	INIT_LIST_HEAD(&cset->mg_dst_preload_node);
 	INIT_LIST_HEAD(&cset->mg_node);
 
 	/* Copy the set of subsystem state objects generated in
@@ -1329,7 +1332,7 @@
 
 void cgroup_free_root(struct cgroup_root *root)
 {
-	kfree(root);
+	kfree_rcu(root, rcu);
 }
 
 static void cgroup_destroy_root(struct cgroup_root *root)
@@ -1362,7 +1365,7 @@
 	spin_unlock_irq(&css_set_lock);
 
 	if (!list_empty(&root->root_list)) {
-		list_del(&root->root_list);
+		list_del_rcu(&root->root_list);
 		cgroup_root_count--;
 	}
 
@@ -1376,75 +1379,89 @@
 }
 
 /*
- * look up cgroup associated with current task's cgroup namespace on the
- * specified hierarchy
+ * Returned cgroup is without refcount but it's valid as long as cset pins it.
  */
-static struct cgroup *
-current_cgns_cgroup_from_root(struct cgroup_root *root)
+static inline struct cgroup *__cset_cgroup_from_root(struct css_set *cset,
+					    struct cgroup_root *root)
 {
-	struct cgroup *res = NULL;
-	struct css_set *cset;
-
-	lockdep_assert_held(&css_set_lock);
+	struct cgroup *res_cgroup = NULL;
 
-	rcu_read_lock();
-
-	cset = current->nsproxy->cgroup_ns->root_cset;
 	if (cset == &init_css_set) {
-		res = &root->cgrp;
+		res_cgroup = &root->cgrp;
 	} else if (root == &cgrp_dfl_root) {
-		res = cset->dfl_cgrp;
+		res_cgroup = cset->dfl_cgrp;
 	} else {
 		struct cgrp_cset_link *link;
+		lockdep_assert_held(&css_set_lock);
 
 		list_for_each_entry(link, &cset->cgrp_links, cgrp_link) {
 			struct cgroup *c = link->cgrp;
 
 			if (c->root == root) {
-				res = c;
+				res_cgroup = c;
 				break;
 			}
 		}
 	}
-	rcu_read_unlock();
 
-	BUG_ON(!res);
-	return res;
+	return res_cgroup;
 }
 
-/* look up cgroup associated with given css_set on the specified hierarchy */
-static struct cgroup *cset_cgroup_from_root(struct css_set *cset,
-					    struct cgroup_root *root)
+/*
+ * look up cgroup associated with current task's cgroup namespace on the
+ * specified hierarchy
+ */
+static struct cgroup *
+current_cgns_cgroup_from_root(struct cgroup_root *root)
 {
 	struct cgroup *res = NULL;
+	struct css_set *cset;
 
-	lockdep_assert_held(&cgroup_mutex);
 	lockdep_assert_held(&css_set_lock);
 
-	if (cset == &init_css_set) {
-		res = &root->cgrp;
-	} else if (root == &cgrp_dfl_root) {
-		res = cset->dfl_cgrp;
-	} else {
-		struct cgrp_cset_link *link;
+	rcu_read_lock();
 
-		list_for_each_entry(link, &cset->cgrp_links, cgrp_link) {
-			struct cgroup *c = link->cgrp;
+	cset = current->nsproxy->cgroup_ns->root_cset;
+	res = __cset_cgroup_from_root(cset, root);
 
-			if (c->root == root) {
-				res = c;
-				break;
-			}
-		}
-	}
+	rcu_read_unlock();
 
-	BUG_ON(!res);
 	return res;
 }
 
 /*
+ * Look up cgroup associated with current task's cgroup namespace on the default
+ * hierarchy.
+ *
+ * Unlike current_cgns_cgroup_from_root(), this doesn't need locks:
+ * - Internal rcu_read_lock is unnecessary because we don't dereference any rcu
+ *   pointers.
+ * - css_set_lock is not needed because we just read cset->dfl_cgrp.
+ * - As a bonus returned cgrp is pinned with the current because it cannot
+ *   switch cgroup_ns asynchronously.
+ */
+static struct cgroup *current_cgns_cgroup_dfl(void)
+{
+	struct css_set *cset;
+
+	cset = current->nsproxy->cgroup_ns->root_cset;
+	return __cset_cgroup_from_root(cset, &cgrp_dfl_root);
+}
+
+/* look up cgroup associated with given css_set on the specified hierarchy */
+static struct cgroup *cset_cgroup_from_root(struct css_set *cset,
+					    struct cgroup_root *root)
+{
+	lockdep_assert_held(&css_set_lock);
+
+	return __cset_cgroup_from_root(cset, root);
+}
+
+/*
  * Return the cgroup for "task" from the given hierarchy. Must be
- * called with cgroup_mutex and css_set_lock held.
+ * called with css_set_lock held to prevent task's groups from being modified.
+ * Must be called with either cgroup_mutex or rcu read lock to prevent the
+ * cgroup root from being destroyed.
  */
 struct cgroup *task_cgroup_from_root(struct task_struct *task,
 				     struct cgroup_root *root)
@@ -1739,7 +1756,8 @@
 {
 	struct cgroup *dcgrp = &dst_root->cgrp;
 	struct cgroup_subsys *ss;
-	int ssid, i, ret;
+	int ssid, ret;
+	u16 dfl_disable_ss_mask = 0;
 
 	lockdep_assert_held(&cgroup_mutex);
 
@@ -1756,35 +1774,72 @@
 		/* can't move between two non-dummy roots either */
 		if (ss->root != &cgrp_dfl_root && dst_root != &cgrp_dfl_root)
 			return -EBUSY;
+
+		/*
+		 * Collect ssid's that need to be disabled from default
+		 * hierarchy.
+		 */
+		if (ss->root == &cgrp_dfl_root)
+			dfl_disable_ss_mask |= 1 << ssid;
+
 	} while_each_subsys_mask();
 
+	if (dfl_disable_ss_mask) {
+		struct cgroup *scgrp = &cgrp_dfl_root.cgrp;
+
+		/*
+		 * Controllers from default hierarchy that need to be rebound
+		 * are all disabled together in one go.
+		 */
+		cgrp_dfl_root.subsys_mask &= ~dfl_disable_ss_mask;
+		WARN_ON(cgroup_apply_control(scgrp));
+		cgroup_finalize_control(scgrp, 0);
+	}
+
 	do_each_subsys_mask(ss, ssid, ss_mask) {
 		struct cgroup_root *src_root = ss->root;
 		struct cgroup *scgrp = &src_root->cgrp;
 		struct cgroup_subsys_state *css = cgroup_css(scgrp, ss);
-		struct css_set *cset;
+		struct css_set *cset, *cset_pos;
+		struct css_task_iter *it;
 
 		WARN_ON(!css || cgroup_css(dcgrp, ss));
 
-		/* disable from the source */
-		src_root->subsys_mask &= ~(1 << ssid);
-		WARN_ON(cgroup_apply_control(scgrp));
-		cgroup_finalize_control(scgrp, 0);
+		if (src_root != &cgrp_dfl_root) {
+			/* disable from the source */
+			src_root->subsys_mask &= ~(1 << ssid);
+			WARN_ON(cgroup_apply_control(scgrp));
+			cgroup_finalize_control(scgrp, 0);
+		}
 
 		/* rebind */
 		RCU_INIT_POINTER(scgrp->subsys[ssid], NULL);
 		rcu_assign_pointer(dcgrp->subsys[ssid], css);
 		ss->root = dst_root;
-		css->cgroup = dcgrp;
 
 		spin_lock_irq(&css_set_lock);
-		hash_for_each(css_set_table, i, cset, hlist)
+		css->cgroup = dcgrp;
+		WARN_ON(!list_empty(&dcgrp->e_csets[ss->id]));
+		list_for_each_entry_safe(cset, cset_pos, &scgrp->e_csets[ss->id],
+					 e_cset_node[ss->id]) {
 			list_move_tail(&cset->e_cset_node[ss->id],
 				       &dcgrp->e_csets[ss->id]);
+			/*
+			 * all css_sets of scgrp together in same order to dcgrp,
+			 * patch in-flight iterators to preserve correct iteration.
+			 * since the iterator is always advanced right away and
+			 * finished when it->cset_pos meets it->cset_head, so only
+			 * update it->cset_head is enough here.
+			 */
+			list_for_each_entry(it, &cset->task_iters, iters_node)
+				if (it->cset_head == &scgrp->e_csets[ss->id])
+					it->cset_head = &dcgrp->e_csets[ss->id];
+		}
 		spin_unlock_irq(&css_set_lock);
 
 		if (ss->css_rstat_flush) {
 			list_del_rcu(&css->rstat_css_node);
+			synchronize_rcu();
 			list_add_rcu(&css->rstat_css_node,
 				     &dcgrp->rstat_css_list);
 		}
@@ -1945,7 +2000,7 @@
 	struct cgroup_root *root = ctx->root;
 	struct cgroup *cgrp = &root->cgrp;
 
-	INIT_LIST_HEAD(&root->root_list);
+	INIT_LIST_HEAD_RCU(&root->root_list);
 	atomic_set(&root->nr_cgrps, 1);
 	cgrp->root = root;
 	init_cgroup_housekeeping(cgrp);
@@ -2017,8 +2072,10 @@
 	if (ret)
 		goto exit_stats;
 
-	ret = cgroup_bpf_inherit(root_cgrp);
-	WARN_ON_ONCE(ret);
+	if (root == &cgrp_dfl_root) {
+		ret = cgroup_bpf_inherit(root_cgrp);
+		WARN_ON_ONCE(ret);
+	}
 
 	trace_cgroup_setup_root(root);
 
@@ -2027,7 +2084,7 @@
 	 * care of subsystems' refcounts, which are explicitly dropped in
 	 * the failure exit path.
 	 */
-	list_add(&root->root_list, &cgroup_roots);
+	list_add_rcu(&root->root_list, &cgroup_roots);
 	cgroup_root_count++;
 
 	/*
@@ -2187,10 +2244,8 @@
 	 * And don't kill the default root.
 	 */
 	if (list_empty(&root->cgrp.self.children) && root != &cgrp_dfl_root &&
-	    !percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
-		cgroup_bpf_offline(&root->cgrp);
+	    !percpu_ref_is_dying(&root->cgrp.self.refcnt))
 		percpu_ref_kill(&root->cgrp.self.refcnt);
-	}
 	cgroup_put(&root->cgrp);
 	kernfs_kill_sb(sb);
 }
@@ -2320,6 +2375,47 @@
 EXPORT_SYMBOL_GPL(task_cgroup_path);
 
 /**
+ * cgroup_attach_lock - Lock for ->attach()
+ * @lock_threadgroup: whether to down_write cgroup_threadgroup_rwsem
+ *
+ * cgroup migration sometimes needs to stabilize threadgroups against forks and
+ * exits by write-locking cgroup_threadgroup_rwsem. However, some ->attach()
+ * implementations (e.g. cpuset), also need to disable CPU hotplug.
+ * Unfortunately, letting ->attach() operations acquire cpus_read_lock() can
+ * lead to deadlocks.
+ *
+ * Bringing up a CPU may involve creating and destroying tasks which requires
+ * read-locking threadgroup_rwsem, so threadgroup_rwsem nests inside
+ * cpus_read_lock(). If we call an ->attach() which acquires the cpus lock while
+ * write-locking threadgroup_rwsem, the locking order is reversed and we end up
+ * waiting for an on-going CPU hotplug operation which in turn is waiting for
+ * the threadgroup_rwsem to be released to create new tasks. For more details:
+ *
+ *   http://lkml.kernel.org/r/20220711174629.uehfmqegcwn2lqzu@wubuntu
+ *
+ * Resolve the situation by always acquiring cpus_read_lock() before optionally
+ * write-locking cgroup_threadgroup_rwsem. This allows ->attach() to assume that
+ * CPU hotplug is disabled on entry.
+ */
+static void cgroup_attach_lock(bool lock_threadgroup)
+{
+	cpus_read_lock();
+	if (lock_threadgroup)
+		percpu_down_write(&cgroup_threadgroup_rwsem);
+}
+
+/**
+ * cgroup_attach_unlock - Undo cgroup_attach_lock()
+ * @lock_threadgroup: whether to up_write cgroup_threadgroup_rwsem
+ */
+static void cgroup_attach_unlock(bool lock_threadgroup)
+{
+	if (lock_threadgroup)
+		percpu_up_write(&cgroup_threadgroup_rwsem);
+	cpus_read_unlock();
+}
+
+/**
  * cgroup_migrate_add_task - add a migration target task to a migration context
  * @task: target task
  * @mgctx: target migration context
@@ -2573,21 +2669,27 @@
  */
 void cgroup_migrate_finish(struct cgroup_mgctx *mgctx)
 {
-	LIST_HEAD(preloaded);
 	struct css_set *cset, *tmp_cset;
 
 	lockdep_assert_held(&cgroup_mutex);
 
 	spin_lock_irq(&css_set_lock);
 
-	list_splice_tail_init(&mgctx->preloaded_src_csets, &preloaded);
-	list_splice_tail_init(&mgctx->preloaded_dst_csets, &preloaded);
+	list_for_each_entry_safe(cset, tmp_cset, &mgctx->preloaded_src_csets,
+				 mg_src_preload_node) {
+		cset->mg_src_cgrp = NULL;
+		cset->mg_dst_cgrp = NULL;
+		cset->mg_dst_cset = NULL;
+		list_del_init(&cset->mg_src_preload_node);
+		put_css_set_locked(cset);
+	}
 
-	list_for_each_entry_safe(cset, tmp_cset, &preloaded, mg_preload_node) {
+	list_for_each_entry_safe(cset, tmp_cset, &mgctx->preloaded_dst_csets,
+				 mg_dst_preload_node) {
 		cset->mg_src_cgrp = NULL;
 		cset->mg_dst_cgrp = NULL;
 		cset->mg_dst_cset = NULL;
-		list_del_init(&cset->mg_preload_node);
+		list_del_init(&cset->mg_dst_preload_node);
 		put_css_set_locked(cset);
 	}
 
@@ -2629,7 +2731,7 @@
 
 	src_cgrp = cset_cgroup_from_root(src_cset, dst_cgrp->root);
 
-	if (!list_empty(&src_cset->mg_preload_node))
+	if (!list_empty(&src_cset->mg_src_preload_node))
 		return;
 
 	WARN_ON(src_cset->mg_src_cgrp);
@@ -2640,7 +2742,7 @@
 	src_cset->mg_src_cgrp = src_cgrp;
 	src_cset->mg_dst_cgrp = dst_cgrp;
 	get_css_set(src_cset);
-	list_add_tail(&src_cset->mg_preload_node, &mgctx->preloaded_src_csets);
+	list_add_tail(&src_cset->mg_src_preload_node, &mgctx->preloaded_src_csets);
 }
 
 /**
@@ -2665,7 +2767,7 @@
 
 	/* look up the dst cset for each src cset and link it to src */
 	list_for_each_entry_safe(src_cset, tmp_cset, &mgctx->preloaded_src_csets,
-				 mg_preload_node) {
+				 mg_src_preload_node) {
 		struct css_set *dst_cset;
 		struct cgroup_subsys *ss;
 		int ssid;
@@ -2684,7 +2786,7 @@
 		if (src_cset == dst_cset) {
 			src_cset->mg_src_cgrp = NULL;
 			src_cset->mg_dst_cgrp = NULL;
-			list_del_init(&src_cset->mg_preload_node);
+			list_del_init(&src_cset->mg_src_preload_node);
 			put_css_set(src_cset);
 			put_css_set(dst_cset);
 			continue;
@@ -2692,8 +2794,8 @@
 
 		src_cset->mg_dst_cset = dst_cset;
 
-		if (list_empty(&dst_cset->mg_preload_node))
-			list_add_tail(&dst_cset->mg_preload_node,
+		if (list_empty(&dst_cset->mg_dst_preload_node))
+			list_add_tail(&dst_cset->mg_dst_preload_node,
 				      &mgctx->preloaded_dst_csets);
 		else
 			put_css_set(dst_cset);
@@ -2789,8 +2891,7 @@
 }
 
 struct task_struct *cgroup_procs_write_start(char *buf, bool threadgroup,
-					     bool *locked)
-	__acquires(&cgroup_threadgroup_rwsem)
+					     bool *threadgroup_locked)
 {
 	struct task_struct *tsk;
 	pid_t pid;
@@ -2807,12 +2908,8 @@
 	 * Therefore, we can skip the global lock.
 	 */
 	lockdep_assert_held(&cgroup_mutex);
-	if (pid || threadgroup) {
-		percpu_down_write(&cgroup_threadgroup_rwsem);
-		*locked = true;
-	} else {
-		*locked = false;
-	}
+	*threadgroup_locked = pid || threadgroup;
+	cgroup_attach_lock(*threadgroup_locked);
 
 	rcu_read_lock();
 	if (pid) {
@@ -2843,17 +2940,14 @@
 	goto out_unlock_rcu;
 
 out_unlock_threadgroup:
-	if (*locked) {
-		percpu_up_write(&cgroup_threadgroup_rwsem);
-		*locked = false;
-	}
+	cgroup_attach_unlock(*threadgroup_locked);
+	*threadgroup_locked = false;
 out_unlock_rcu:
 	rcu_read_unlock();
 	return tsk;
 }
 
-void cgroup_procs_write_finish(struct task_struct *task, bool locked)
-	__releases(&cgroup_threadgroup_rwsem)
+void cgroup_procs_write_finish(struct task_struct *task, bool threadgroup_locked)
 {
 	struct cgroup_subsys *ss;
 	int ssid;
@@ -2861,8 +2955,8 @@
 	/* release reference from cgroup_procs_write_start() */
 	put_task_struct(task);
 
-	if (locked)
-		percpu_up_write(&cgroup_threadgroup_rwsem);
+	cgroup_attach_unlock(threadgroup_locked);
+
 	for_each_subsys(ss, ssid)
 		if (ss->post_attach)
 			ss->post_attach();
@@ -2917,12 +3011,11 @@
 	struct cgroup_subsys_state *d_css;
 	struct cgroup *dsct;
 	struct css_set *src_cset;
+	bool has_tasks;
 	int ret;
 
 	lockdep_assert_held(&cgroup_mutex);
 
-	percpu_down_write(&cgroup_threadgroup_rwsem);
-
 	/* look up all csses currently attached to @cgrp's subtree */
 	spin_lock_irq(&css_set_lock);
 	cgroup_for_each_live_descendant_pre(dsct, d_css, cgrp) {
@@ -2933,13 +3026,23 @@
 	}
 	spin_unlock_irq(&css_set_lock);
 
+	/*
+	 * We need to write-lock threadgroup_rwsem while migrating tasks.
+	 * However, if there are no source csets for @cgrp, changing its
+	 * controllers isn't gonna produce any task migrations and the
+	 * write-locking can be skipped safely.
+	 */
+	has_tasks = !list_empty(&mgctx.preloaded_src_csets);
+	cgroup_attach_lock(has_tasks);
+
 	/* NULL dst indicates self on default hierarchy */
 	ret = cgroup_migrate_prepare_dst(&mgctx);
 	if (ret)
 		goto out_finish;
 
 	spin_lock_irq(&css_set_lock);
-	list_for_each_entry(src_cset, &mgctx.preloaded_src_csets, mg_preload_node) {
+	list_for_each_entry(src_cset, &mgctx.preloaded_src_csets,
+			    mg_src_preload_node) {
 		struct task_struct *task, *ntask;
 
 		/* all tasks in src_csets need to be migrated */
@@ -2951,7 +3054,7 @@
 	ret = cgroup_migrate_execute(&mgctx);
 out_finish:
 	cgroup_migrate_finish(&mgctx);
-	percpu_up_write(&cgroup_threadgroup_rwsem);
+	cgroup_attach_unlock(has_tasks);
 	return ret;
 }
 
@@ -3607,6 +3710,7 @@
 static ssize_t cgroup_pressure_write(struct kernfs_open_file *of, char *buf,
 					  size_t nbytes, enum psi_res res)
 {
+	struct cgroup_file_ctx *ctx = of->priv;
 	struct psi_trigger *new;
 	struct cgroup *cgrp;
 	struct psi_group *psi;
@@ -3618,6 +3722,12 @@
 	cgroup_get(cgrp);
 	cgroup_kn_unlock(of->kn);
 
+	/* Allow only one trigger per file descriptor */
+	if (ctx->psi.trigger) {
+		cgroup_put(cgrp);
+		return -EBUSY;
+	}
+
 	psi = cgroup_ino(cgrp) == 1 ? &psi_system : &cgrp->psi;
 	new = psi_trigger_create(psi, buf, nbytes, res);
 	if (IS_ERR(new)) {
@@ -3625,8 +3735,7 @@
 		return PTR_ERR(new);
 	}
 
-	psi_trigger_replace(&of->priv, new);
-
+	smp_store_release(&ctx->psi.trigger, new);
 	cgroup_put(cgrp);
 
 	return nbytes;
@@ -3656,12 +3765,16 @@
 static __poll_t cgroup_pressure_poll(struct kernfs_open_file *of,
 					  poll_table *pt)
 {
-	return psi_trigger_poll(&of->priv, of->file, pt);
+	struct cgroup_file_ctx *ctx = of->priv;
+
+	return psi_trigger_poll(&ctx->psi.trigger, of->file, pt);
 }
 
 static void cgroup_pressure_release(struct kernfs_open_file *of)
 {
-	psi_trigger_replace(&of->priv, NULL);
+	struct cgroup_file_ctx *ctx = of->priv;
+
+	psi_trigger_destroy(ctx->psi.trigger);
 }
 
 bool cgroup_psi_enabled(void)
@@ -3719,7 +3832,7 @@
 	lockdep_assert_held(&cgroup_mutex);
 
 	spin_lock_irq(&css_set_lock);
-	set_bit(CGRP_KILL, &cgrp->flags);
+	cgrp->kill_seq++;
 	spin_unlock_irq(&css_set_lock);
 
 	css_task_iter_start(&cgrp->self, CSS_TASK_ITER_PROCS | CSS_TASK_ITER_THREADED, &it);
@@ -3735,10 +3848,6 @@
 		send_sig(SIGKILL, task, 0);
 	}
 	css_task_iter_end(&it);
-
-	spin_lock_irq(&css_set_lock);
-	clear_bit(CGRP_KILL, &cgrp->flags);
-	spin_unlock_irq(&css_set_lock);
 }
 
 static void cgroup_kill(struct cgroup *cgrp)
@@ -3788,24 +3897,43 @@
 static int cgroup_file_open(struct kernfs_open_file *of)
 {
 	struct cftype *cft = of_cft(of);
+	struct cgroup_file_ctx *ctx;
+	int ret;
 
-	if (cft->open)
-		return cft->open(of);
-	return 0;
+	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->ns = current->nsproxy->cgroup_ns;
+	get_cgroup_ns(ctx->ns);
+	of->priv = ctx;
+
+	if (!cft->open)
+		return 0;
+
+	ret = cft->open(of);
+	if (ret) {
+		put_cgroup_ns(ctx->ns);
+		kfree(ctx);
+	}
+	return ret;
 }
 
 static void cgroup_file_release(struct kernfs_open_file *of)
 {
 	struct cftype *cft = of_cft(of);
+	struct cgroup_file_ctx *ctx = of->priv;
 
 	if (cft->release)
 		cft->release(of);
+	put_cgroup_ns(ctx->ns);
+	kfree(ctx);
 }
 
 static ssize_t cgroup_file_write(struct kernfs_open_file *of, char *buf,
 				 size_t nbytes, loff_t off)
 {
-	struct cgroup_namespace *ns = current->nsproxy->cgroup_ns;
+	struct cgroup_file_ctx *ctx = of->priv;
 	struct cgroup *cgrp = of->kn->parent->priv;
 	struct cftype *cft = of_cft(of);
 	struct cgroup_subsys_state *css;
@@ -3822,7 +3950,7 @@
 	 */
 	if ((cgrp->root->flags & CGRP_ROOT_NS_DELEGATE) &&
 	    !(cft->flags & CFTYPE_NS_DELEGATABLE) &&
-	    ns != &init_cgroup_ns && ns->root_cset->dfl_cgrp == cgrp)
+	    ctx->ns != &init_cgroup_ns && ctx->ns->root_cset->dfl_cgrp == cgrp)
 		return -EPERM;
 
 	if (cft->write)
@@ -4728,21 +4856,21 @@
 
 static void cgroup_procs_release(struct kernfs_open_file *of)
 {
-	if (of->priv) {
-		css_task_iter_end(of->priv);
-		kfree(of->priv);
-	}
+	struct cgroup_file_ctx *ctx = of->priv;
+
+	if (ctx->procs.started)
+		css_task_iter_end(&ctx->procs.iter);
 }
 
 static void *cgroup_procs_next(struct seq_file *s, void *v, loff_t *pos)
 {
 	struct kernfs_open_file *of = s->private;
-	struct css_task_iter *it = of->priv;
+	struct cgroup_file_ctx *ctx = of->priv;
 
 	if (pos)
 		(*pos)++;
 
-	return css_task_iter_next(it);
+	return css_task_iter_next(&ctx->procs.iter);
 }
 
 static void *__cgroup_procs_start(struct seq_file *s, loff_t *pos,
@@ -4750,21 +4878,18 @@
 {
 	struct kernfs_open_file *of = s->private;
 	struct cgroup *cgrp = seq_css(s)->cgroup;
-	struct css_task_iter *it = of->priv;
+	struct cgroup_file_ctx *ctx = of->priv;
+	struct css_task_iter *it = &ctx->procs.iter;
 
 	/*
 	 * When a seq_file is seeked, it's always traversed sequentially
 	 * from position 0, so we can simply keep iterating on !0 *pos.
 	 */
-	if (!it) {
+	if (!ctx->procs.started) {
 		if (WARN_ON_ONCE((*pos)))
 			return ERR_PTR(-EINVAL);
-
-		it = kzalloc(sizeof(*it), GFP_KERNEL);
-		if (!it)
-			return ERR_PTR(-ENOMEM);
-		of->priv = it;
 		css_task_iter_start(&cgrp->self, iter_flags, it);
+		ctx->procs.started = true;
 	} else if (!(*pos)) {
 		css_task_iter_end(it);
 		css_task_iter_start(&cgrp->self, iter_flags, it);
@@ -4815,9 +4940,9 @@
 
 static int cgroup_procs_write_permission(struct cgroup *src_cgrp,
 					 struct cgroup *dst_cgrp,
-					 struct super_block *sb)
+					 struct super_block *sb,
+					 struct cgroup_namespace *ns)
 {
-	struct cgroup_namespace *ns = current->nsproxy->cgroup_ns;
 	struct cgroup *com_cgrp = src_cgrp;
 	int ret;
 
@@ -4846,11 +4971,12 @@
 
 static int cgroup_attach_permissions(struct cgroup *src_cgrp,
 				     struct cgroup *dst_cgrp,
-				     struct super_block *sb, bool threadgroup)
+				     struct super_block *sb, bool threadgroup,
+				     struct cgroup_namespace *ns)
 {
 	int ret = 0;
 
-	ret = cgroup_procs_write_permission(src_cgrp, dst_cgrp, sb);
+	ret = cgroup_procs_write_permission(src_cgrp, dst_cgrp, sb, ns);
 	if (ret)
 		return ret;
 
@@ -4867,16 +4993,18 @@
 static ssize_t __cgroup_procs_write(struct kernfs_open_file *of, char *buf,
 				    bool threadgroup)
 {
+	struct cgroup_file_ctx *ctx = of->priv;
 	struct cgroup *src_cgrp, *dst_cgrp;
 	struct task_struct *task;
+	const struct cred *saved_cred;
 	ssize_t ret;
-	bool locked;
+	bool threadgroup_locked;
 
 	dst_cgrp = cgroup_kn_lock_live(of->kn, false);
 	if (!dst_cgrp)
 		return -ENODEV;
 
-	task = cgroup_procs_write_start(buf, threadgroup, &locked);
+	task = cgroup_procs_write_start(buf, threadgroup, &threadgroup_locked);
 	ret = PTR_ERR_OR_ZERO(task);
 	if (ret)
 		goto out_unlock;
@@ -4886,16 +5014,23 @@
 	src_cgrp = task_cgroup_from_root(task, &cgrp_dfl_root);
 	spin_unlock_irq(&css_set_lock);
 
-	/* process and thread migrations follow same delegation rule */
+	/*
+	 * Process and thread migrations follow same delegation rule. Check
+	 * permissions using the credentials from file open to protect against
+	 * inherited fd attacks.
+	 */
+	saved_cred = override_creds(of->file->f_cred);
 	ret = cgroup_attach_permissions(src_cgrp, dst_cgrp,
-					of->file->f_path.dentry->d_sb, threadgroup);
+					of->file->f_path.dentry->d_sb,
+					threadgroup, ctx->ns);
+	revert_creds(saved_cred);
 	if (ret)
 		goto out_finish;
 
 	ret = cgroup_attach_task(dst_cgrp, task, threadgroup);
 
 out_finish:
-	cgroup_procs_write_finish(task, locked);
+	cgroup_procs_write_finish(task, threadgroup_locked);
 out_unlock:
 	cgroup_kn_unlock(of->kn);
 
@@ -5323,9 +5458,11 @@
 	if (ret)
 		goto out_kernfs_remove;
 
-	ret = cgroup_bpf_inherit(cgrp);
-	if (ret)
-		goto out_psi_free;
+	if (cgrp->root == &cgrp_dfl_root) {
+		ret = cgroup_bpf_inherit(cgrp);
+		if (ret)
+			goto out_psi_free;
+	}
 
 	/*
 	 * New cgroup inherits effective freeze counter, and
@@ -5402,7 +5539,7 @@
 {
 	struct cgroup *cgroup;
 	int ret = false;
-	int level = 1;
+	int level = 0;
 
 	lockdep_assert_held(&cgroup_mutex);
 
@@ -5410,7 +5547,7 @@
 		if (cgroup->nr_descendants >= cgroup->max_descendants)
 			goto fail;
 
-		if (level > cgroup->max_depth)
+		if (level >= cgroup->max_depth)
 			goto fail;
 
 		level++;
@@ -5643,7 +5780,8 @@
 
 	cgroup1_check_for_release(parent);
 
-	cgroup_bpf_offline(cgrp);
+	if (cgrp->root == &cgrp_dfl_root)
+		cgroup_bpf_offline(cgrp);
 
 	/* put the base reference */
 	percpu_ref_kill(&cgrp->self.refcnt);
@@ -5904,24 +6042,41 @@
 /*
  * cgroup_get_from_id : get the cgroup associated with cgroup id
  * @id: cgroup id
- * On success return the cgrp, on failure return NULL
+ * On success return the cgrp or ERR_PTR on failure
+ * Only cgroups within current task's cgroup NS are valid.
  */
 struct cgroup *cgroup_get_from_id(u64 id)
 {
 	struct kernfs_node *kn;
-	struct cgroup *cgrp = NULL;
+	struct cgroup *cgrp, *root_cgrp;
 
-	mutex_lock(&cgroup_mutex);
 	kn = kernfs_find_and_get_node_by_id(cgrp_dfl_root.kf_root, id);
 	if (!kn)
-		goto out_unlock;
+		return ERR_PTR(-ENOENT);
 
-	cgrp = kn->priv;
-	if (cgroup_is_dead(cgrp) || !cgroup_tryget(cgrp))
+	if (kernfs_type(kn) != KERNFS_DIR) {
+		kernfs_put(kn);
+		return ERR_PTR(-ENOENT);
+	}
+
+	rcu_read_lock();
+
+	cgrp = rcu_dereference(*(void __rcu __force **)&kn->priv);
+	if (cgrp && !cgroup_tryget(cgrp))
 		cgrp = NULL;
+
+	rcu_read_unlock();
 	kernfs_put(kn);
-out_unlock:
-	mutex_unlock(&cgroup_mutex);
+
+	if (!cgrp)
+		return ERR_PTR(-ENOENT);
+
+	root_cgrp = current_cgns_cgroup_dfl();
+	if (!cgroup_is_descendant(cgrp, root_cgrp)) {
+		cgroup_put(cgrp);
+		return ERR_PTR(-ENOENT);
+	}
+
 	return cgrp;
 }
 EXPORT_SYMBOL_GPL(cgroup_get_from_id);
@@ -6068,6 +6223,10 @@
 	spin_lock_irq(&css_set_lock);
 	cset = task_css_set(current);
 	get_css_set(cset);
+	if (kargs->cgrp)
+		kargs->kill_seq = kargs->cgrp->kill_seq;
+	else
+		kargs->kill_seq = cset->dfl_cgrp->kill_seq;
 	spin_unlock_irq(&css_set_lock);
 
 	if (!(kargs->flags & CLONE_INTO_CGROUP)) {
@@ -6104,7 +6263,8 @@
 		goto err;
 
 	ret = cgroup_attach_permissions(cset->dfl_cgrp, dst_cgrp, sb,
-					!(kargs->flags & CLONE_THREAD));
+					!(kargs->flags & CLONE_THREAD),
+					current->nsproxy->cgroup_ns);
 	if (ret)
 		goto err;
 
@@ -6142,19 +6302,18 @@
 static void cgroup_css_set_put_fork(struct kernel_clone_args *kargs)
 	__releases(&cgroup_threadgroup_rwsem) __releases(&cgroup_mutex)
 {
+	struct cgroup *cgrp = kargs->cgrp;
+	struct css_set *cset = kargs->cset;
+
 	cgroup_threadgroup_change_end(current);
 
-	if (kargs->flags & CLONE_INTO_CGROUP) {
-		struct cgroup *cgrp = kargs->cgrp;
-		struct css_set *cset = kargs->cset;
+	if (cset) {
+		put_css_set(cset);
+		kargs->cset = NULL;
+	}
 
+	if (kargs->flags & CLONE_INTO_CGROUP) {
 		mutex_unlock(&cgroup_mutex);
-
-		if (cset) {
-			put_css_set(cset);
-			kargs->cset = NULL;
-		}
-
 		if (cgrp) {
 			cgroup_put(cgrp);
 			kargs->cgrp = NULL;
@@ -6235,6 +6394,7 @@
 		      struct kernel_clone_args *kargs)
 	__releases(&cgroup_threadgroup_rwsem) __releases(&cgroup_mutex)
 {
+	unsigned int cgrp_kill_seq = 0;
 	unsigned long cgrp_flags = 0;
 	bool kill = false;
 	struct cgroup_subsys *ss;
@@ -6248,10 +6408,13 @@
 
 	/* init tasks are special, only link regular threads */
 	if (likely(child->pid)) {
-		if (kargs->cgrp)
+		if (kargs->cgrp) {
 			cgrp_flags = kargs->cgrp->flags;
-		else
+			cgrp_kill_seq = kargs->cgrp->kill_seq;
+		} else {
 			cgrp_flags = cset->dfl_cgrp->flags;
+			cgrp_kill_seq = cset->dfl_cgrp->kill_seq;
+		}
 
 		WARN_ON_ONCE(!list_empty(&child->cg_list));
 		cset->nr_tasks++;
@@ -6286,7 +6449,7 @@
 		 * child down right after we finished preparing it for
 		 * userspace.
 		 */
-		kill = test_bit(CGRP_KILL, &cgrp_flags);
+		kill = kargs->kill_seq != cgrp_kill_seq;
 	}
 
 	spin_unlock_irq(&css_set_lock);
@@ -6337,6 +6500,9 @@
 	list_add_tail(&tsk->cg_list, &cset->dying_tasks);
 	cset->nr_tasks--;
 
+	if (dl_task(tsk))
+		dec_dl_tasks_cs(tsk);
+
 	WARN_ON_ONCE(cgroup_task_frozen(tsk));
 	if (unlikely(!(tsk->flags & PF_KTHREAD) &&
 		     test_bit(CGRP_FREEZE, &task_dfl_cgroup(tsk)->flags)))
@@ -6474,30 +6640,36 @@
  *
  * Find the cgroup at @path on the default hierarchy, increment its
  * reference count and return it.  Returns pointer to the found cgroup on
- * success, ERR_PTR(-ENOENT) if @path doesn't exist and ERR_PTR(-ENOTDIR)
- * if @path points to a non-directory.
+ * success, ERR_PTR(-ENOENT) if @path doesn't exist or if the cgroup has already
+ * been released and ERR_PTR(-ENOTDIR) if @path points to a non-directory.
  */
 struct cgroup *cgroup_get_from_path(const char *path)
 {
 	struct kernfs_node *kn;
-	struct cgroup *cgrp;
+	struct cgroup *cgrp = ERR_PTR(-ENOENT);
+	struct cgroup *root_cgrp;
 
-	mutex_lock(&cgroup_mutex);
+	root_cgrp = current_cgns_cgroup_dfl();
+	kn = kernfs_walk_and_get(root_cgrp->kn, path);
+	if (!kn)
+		goto out;
 
-	kn = kernfs_walk_and_get(cgrp_dfl_root.cgrp.kn, path);
-	if (kn) {
-		if (kernfs_type(kn) == KERNFS_DIR) {
-			cgrp = kn->priv;
-			cgroup_get_live(cgrp);
-		} else {
-			cgrp = ERR_PTR(-ENOTDIR);
-		}
-		kernfs_put(kn);
-	} else {
-		cgrp = ERR_PTR(-ENOENT);
+	if (kernfs_type(kn) != KERNFS_DIR) {
+		cgrp = ERR_PTR(-ENOTDIR);
+		goto out_kernfs;
 	}
 
-	mutex_unlock(&cgroup_mutex);
+	rcu_read_lock();
+
+	cgrp = rcu_dereference(*(void __rcu __force **)&kn->priv);
+	if (!cgrp || !cgroup_tryget(cgrp))
+		cgrp = ERR_PTR(-ENOENT);
+
+	rcu_read_unlock();
+
+out_kernfs:
+	kernfs_put(kn);
+out:
 	return cgrp;
 }
 EXPORT_SYMBOL_GPL(cgroup_get_from_path);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cgroup/cpuset.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cgroup/cpuset.c
@@ -22,6 +22,7 @@
  *  distribution for more details.
  */
 
+#include "cgroup-internal.h"
 #include <linux/cpu.h>
 #include <linux/cpumask.h>
 #include <linux/cpuset.h>
@@ -33,6 +34,7 @@
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/kmod.h>
+#include <linux/kthread.h>
 #include <linux/list.h>
 #include <linux/mempolicy.h>
 #include <linux/mm.h>
@@ -161,6 +163,14 @@
 	int use_parent_ecpus;
 	int child_ecpus_count;
 
+	/*
+	 * number of SCHED_DEADLINE tasks attached to this cpuset, so that we
+	 * know when to rebuild associated root domain bandwidth information.
+	 */
+	int nr_deadline_tasks;
+	int nr_migrate_dl_tasks;
+	u64 sum_migrate_dl_bw;
+
 	/* Handle for cpuset.cpus.partition */
 	struct cgroup_file partition_file;
 };
@@ -208,6 +218,20 @@
 	return css_cs(cs->css.parent);
 }
 
+void inc_dl_tasks_cs(struct task_struct *p)
+{
+	struct cpuset *cs = task_cs(p);
+
+	cs->nr_deadline_tasks++;
+}
+
+void dec_dl_tasks_cs(struct task_struct *p)
+{
+	struct cpuset *cs = task_cs(p);
+
+	cs->nr_deadline_tasks--;
+}
+
 /* bits in struct cpuset flags field */
 typedef enum {
 	CS_ONLINE,
@@ -311,22 +335,23 @@
 		if (is_cpuset_online(((des_cs) = css_cs((pos_css)))))
 
 /*
- * There are two global locks guarding cpuset structures - cpuset_rwsem and
+ * There are two global locks guarding cpuset structures - cpuset_mutex and
  * callback_lock. We also require taking task_lock() when dereferencing a
  * task's cpuset pointer. See "The task_lock() exception", at the end of this
- * comment.  The cpuset code uses only cpuset_rwsem write lock.  Other
- * kernel subsystems can use cpuset_read_lock()/cpuset_read_unlock() to
- * prevent change to cpuset structures.
+ * comment.  The cpuset code uses only cpuset_mutex. Other kernel subsystems
+ * can use cpuset_lock()/cpuset_unlock() to prevent change to cpuset
+ * structures. Note that cpuset_mutex needs to be a mutex as it is used in
+ * paths that rely on priority inheritance (e.g. scheduler - on RT) for
+ * correctness.
  *
  * A task must hold both locks to modify cpusets.  If a task holds
- * cpuset_rwsem, it blocks others wanting that rwsem, ensuring that it
- * is the only task able to also acquire callback_lock and be able to
- * modify cpusets.  It can perform various checks on the cpuset structure
- * first, knowing nothing will change.  It can also allocate memory while
- * just holding cpuset_rwsem.  While it is performing these checks, various
- * callback routines can briefly acquire callback_lock to query cpusets.
- * Once it is ready to make the changes, it takes callback_lock, blocking
- * everyone else.
+ * cpuset_mutex, it blocks others, ensuring that it is the only task able to
+ * also acquire callback_lock and be able to modify cpusets.  It can perform
+ * various checks on the cpuset structure first, knowing nothing will change.
+ * It can also allocate memory while just holding cpuset_mutex.  While it is
+ * performing these checks, various callback routines can briefly acquire
+ * callback_lock to query cpusets.  Once it is ready to make the changes, it
+ * takes callback_lock, blocking everyone else.
  *
  * Calls to the kernel memory allocator can not be made while holding
  * callback_lock, as that would risk double tripping on callback_lock
@@ -348,16 +373,16 @@
  * guidelines for accessing subsystem state in kernel/cgroup.c
  */
 
-DEFINE_STATIC_PERCPU_RWSEM(cpuset_rwsem);
+static DEFINE_MUTEX(cpuset_mutex);
 
-void cpuset_read_lock(void)
+void cpuset_lock(void)
 {
-	percpu_down_read(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 }
 
-void cpuset_read_unlock(void)
+void cpuset_unlock(void)
 {
-	percpu_up_read(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 }
 
 static DEFINE_SPINLOCK(callback_lock);
@@ -395,7 +420,7 @@
  * One way or another, we guarantee to return some non-empty subset
  * of cpu_online_mask.
  *
- * Call with callback_lock or cpuset_rwsem held.
+ * Call with callback_lock or cpuset_mutex held.
  */
 static void guarantee_online_cpus(struct task_struct *tsk,
 				  struct cpumask *pmask)
@@ -437,7 +462,7 @@
  * One way or another, we guarantee to return some non-empty subset
  * of node_states[N_MEMORY].
  *
- * Call with callback_lock or cpuset_rwsem held.
+ * Call with callback_lock or cpuset_mutex held.
  */
 static void guarantee_online_mems(struct cpuset *cs, nodemask_t *pmask)
 {
@@ -449,7 +474,7 @@
 /*
  * update task's spread flag if cpuset's page/slab spread flag is set
  *
- * Call with callback_lock or cpuset_rwsem held.
+ * Call with callback_lock or cpuset_mutex held.
  */
 static void cpuset_update_task_spread_flag(struct cpuset *cs,
 					struct task_struct *tsk)
@@ -470,7 +495,7 @@
  *
  * One cpuset is a subset of another if all its allowed CPUs and
  * Memory Nodes are a subset of the other, and its exclusive flags
- * are only set if the other's are set.  Call holding cpuset_rwsem.
+ * are only set if the other's are set.  Call holding cpuset_mutex.
  */
 
 static int is_cpuset_subset(const struct cpuset *p, const struct cpuset *q)
@@ -579,7 +604,7 @@
  * If we replaced the flag and mask values of the current cpuset
  * (cur) with those values in the trial cpuset (trial), would
  * our various subset and exclusive rules still be valid?  Presumes
- * cpuset_rwsem held.
+ * cpuset_mutex held.
  *
  * 'cur' is the address of an actual, in-use cpuset.  Operations
  * such as list traversal that depend on the actual address of the
@@ -702,7 +727,7 @@
 	rcu_read_unlock();
 }
 
-/* Must be called with cpuset_rwsem held.  */
+/* Must be called with cpuset_mutex held.  */
 static inline int nr_cpusets(void)
 {
 	/* jump label reference count + the top-level cpuset */
@@ -728,7 +753,7 @@
  * domains when operating in the severe memory shortage situations
  * that could cause allocation failures below.
  *
- * Must be called with cpuset_rwsem held.
+ * Must be called with cpuset_mutex held.
  *
  * The three key local variables below are:
  *    cp - cpuset pointer, used (together with pos_css) to perform a
@@ -939,11 +964,14 @@
 	return ndoms;
 }
 
-static void update_tasks_root_domain(struct cpuset *cs)
+static void dl_update_tasks_root_domain(struct cpuset *cs)
 {
 	struct css_task_iter it;
 	struct task_struct *task;
 
+	if (cs->nr_deadline_tasks == 0)
+		return;
+
 	css_task_iter_start(&cs->css, 0, &it);
 
 	while ((task = css_task_iter_next(&it)))
@@ -952,12 +980,12 @@
 	css_task_iter_end(&it);
 }
 
-static void rebuild_root_domains(void)
+static void dl_rebuild_rd_accounting(void)
 {
 	struct cpuset *cs = NULL;
 	struct cgroup_subsys_state *pos_css;
 
-	percpu_rwsem_assert_held(&cpuset_rwsem);
+	lockdep_assert_held(&cpuset_mutex);
 	lockdep_assert_cpus_held();
 	lockdep_assert_held(&sched_domains_mutex);
 
@@ -980,7 +1008,7 @@
 
 		rcu_read_unlock();
 
-		update_tasks_root_domain(cs);
+		dl_update_tasks_root_domain(cs);
 
 		rcu_read_lock();
 		css_put(&cs->css);
@@ -994,7 +1022,7 @@
 {
 	mutex_lock(&sched_domains_mutex);
 	partition_sched_domains_locked(ndoms_new, doms_new, dattr_new);
-	rebuild_root_domains();
+	dl_rebuild_rd_accounting();
 	mutex_unlock(&sched_domains_mutex);
 }
 
@@ -1007,7 +1035,7 @@
  * 'cpus' is removed, then call this routine to rebuild the
  * scheduler's dynamic sched domains.
  *
- * Call with cpuset_rwsem held.  Takes cpus_read_lock().
+ * Call with cpuset_mutex held.  Takes cpus_read_lock().
  */
 static void rebuild_sched_domains_locked(void)
 {
@@ -1018,7 +1046,7 @@
 	int ndoms;
 
 	lockdep_assert_cpus_held();
-	percpu_rwsem_assert_held(&cpuset_rwsem);
+	lockdep_assert_held(&cpuset_mutex);
 
 	/*
 	 * If we have raced with CPU hotplug, return early to avoid
@@ -1069,9 +1097,9 @@
 void rebuild_sched_domains(void)
 {
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 	rebuild_sched_domains_locked();
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 }
 
@@ -1080,17 +1108,25 @@
  * @cs: the cpuset in which each task's cpus_allowed mask needs to be changed
  *
  * Iterate through each task of @cs updating its cpus_allowed to the
- * effective cpuset's.  As this function is called with cpuset_rwsem held,
+ * effective cpuset's.  As this function is called with cpuset_mutex held,
  * cpuset membership stays stable.
  */
 static void update_tasks_cpumask(struct cpuset *cs)
 {
 	struct css_task_iter it;
 	struct task_struct *task;
+	bool top_cs = cs == &top_cpuset;
 
 	css_task_iter_start(&cs->css, 0, &it);
-	while ((task = css_task_iter_next(&it)))
+	while ((task = css_task_iter_next(&it))) {
+		/*
+		 * Percpu kthreads in top_cpuset are ignored
+		 */
+		if (top_cs && (task->flags & PF_KTHREAD) &&
+		    kthread_is_per_cpu(task))
+			continue;
 		set_cpus_allowed_ptr(task, cs->effective_cpus);
+	}
 	css_task_iter_end(&it);
 }
 
@@ -1179,7 +1215,7 @@
 	int old_prs, new_prs;
 	bool part_error = false;	/* Partition error? */
 
-	percpu_rwsem_assert_held(&cpuset_rwsem);
+	lockdep_assert_held(&cpuset_mutex);
 
 	/*
 	 * The parent must be a partition root.
@@ -1349,7 +1385,7 @@
  *
  * On legacy hierarchy, effective_cpus will be the same with cpu_allowed.
  *
- * Called with cpuset_rwsem held
+ * Called with cpuset_mutex held
  */
 static void update_cpumasks_hier(struct cpuset *cs, struct tmpmasks *tmp)
 {
@@ -1512,10 +1548,15 @@
 	struct cpuset *sibling;
 	struct cgroup_subsys_state *pos_css;
 
+	lockdep_assert_held(&cpuset_mutex);
+
 	/*
 	 * Check all its siblings and call update_cpumasks_hier()
 	 * if their use_parent_ecpus flag is set in order for them
 	 * to use the right effective_cpus value.
+	 *
+	 * The update_cpumasks_hier() function may sleep. So we have to
+	 * release the RCU read lock before calling it.
 	 */
 	rcu_read_lock();
 	cpuset_for_each_child(sibling, pos_css, parent) {
@@ -1523,8 +1564,13 @@
 			continue;
 		if (!sibling->use_parent_ecpus)
 			continue;
+		if (!css_tryget_online(&sibling->css))
+			continue;
 
+		rcu_read_unlock();
 		update_cpumasks_hier(sibling, tmp);
+		rcu_read_lock();
+		css_put(&sibling->css);
 	}
 	rcu_read_unlock();
 }
@@ -1597,8 +1643,7 @@
 	 * Make sure that subparts_cpus is a subset of cpus_allowed.
 	 */
 	if (cs->nr_subparts_cpus) {
-		cpumask_andnot(cs->subparts_cpus, cs->subparts_cpus,
-			       cs->cpus_allowed);
+		cpumask_and(cs->subparts_cpus, cs->subparts_cpus, cs->cpus_allowed);
 		cs->nr_subparts_cpus = cpumask_weight(cs->subparts_cpus);
 	}
 	spin_unlock_irq(&callback_lock);
@@ -1706,12 +1751,12 @@
  * @cs: the cpuset in which each task's mems_allowed mask needs to be changed
  *
  * Iterate through each task of @cs updating its mems_allowed to the
- * effective cpuset's.  As this function is called with cpuset_rwsem held,
+ * effective cpuset's.  As this function is called with cpuset_mutex held,
  * cpuset membership stays stable.
  */
 static void update_tasks_nodemask(struct cpuset *cs)
 {
-	static nodemask_t newmems;	/* protected by cpuset_rwsem */
+	static nodemask_t newmems;	/* protected by cpuset_mutex */
 	struct css_task_iter it;
 	struct task_struct *task;
 
@@ -1724,7 +1769,7 @@
 	 * take while holding tasklist_lock.  Forks can happen - the
 	 * mpol_dup() cpuset_being_rebound check will catch such forks,
 	 * and rebind their vma mempolicies too.  Because we still hold
-	 * the global cpuset_rwsem, we know that no other rebind effort
+	 * the global cpuset_mutex, we know that no other rebind effort
 	 * will be contending for the global variable cpuset_being_rebound.
 	 * It's ok if we rebind the same mm twice; mpol_rebind_mm()
 	 * is idempotent.  Also migrate pages in each mm to new nodes.
@@ -1770,7 +1815,7 @@
  *
  * On legacy hierarchy, effective_mems will be the same with mems_allowed.
  *
- * Called with cpuset_rwsem held
+ * Called with cpuset_mutex held
  */
 static void update_nodemasks_hier(struct cpuset *cs, nodemask_t *new_mems)
 {
@@ -1823,7 +1868,7 @@
  * mempolicies and if the cpuset is marked 'memory_migrate',
  * migrate the tasks pages to the new memory.
  *
- * Call with cpuset_rwsem held. May take callback_lock during call.
+ * Call with cpuset_mutex held. May take callback_lock during call.
  * Will take tasklist_lock, scan tasklist for tasks in cpuset cs,
  * lock each such tasks mm->mmap_lock, scan its vma's and rebind
  * their mempolicies to the cpusets new mems_allowed.
@@ -1894,7 +1939,7 @@
 static int update_relax_domain_level(struct cpuset *cs, s64 val)
 {
 #ifdef CONFIG_SMP
-	if (val < -1 || val >= sched_domain_level_max)
+	if (val < -1 || val > sched_domain_level_max + 1)
 		return -EINVAL;
 #endif
 
@@ -1913,7 +1958,7 @@
  * @cs: the cpuset in which each task's spread flags needs to be changed
  *
  * Iterate through each task of @cs updating its spread flags.  As this
- * function is called with cpuset_rwsem held, cpuset membership stays
+ * function is called with cpuset_mutex held, cpuset membership stays
  * stable.
  */
 static void update_tasks_flags(struct cpuset *cs)
@@ -1933,7 +1978,7 @@
  * cs:		the cpuset to update
  * turning_on: 	whether the flag is being set or cleared
  *
- * Call with cpuset_rwsem held.
+ * Call with cpuset_mutex held.
  */
 
 static int update_flag(cpuset_flagbits_t bit, struct cpuset *cs,
@@ -1982,7 +2027,7 @@
  * cs: the cpuset to update
  * new_prs: new partition root state
  *
- * Call with cpuset_rwsem held.
+ * Call with cpuset_mutex held.
  */
 static int update_prstate(struct cpuset *cs, int new_prs)
 {
@@ -2043,12 +2088,7 @@
 		update_flag(CS_CPU_EXCLUSIVE, cs, 0);
 	}
 
-	/*
-	 * Update cpumask of parent's tasks except when it is the top
-	 * cpuset as some system daemons cannot be mapped to other CPUs.
-	 */
-	if (parent != &top_cpuset)
-		update_tasks_cpumask(parent);
+	update_tasks_cpumask(parent);
 
 	if (parent->child_ecpus_count)
 		update_sibling_cpumasks(parent, cs, &tmpmask);
@@ -2169,19 +2209,26 @@
 
 static struct cpuset *cpuset_attach_old_cs;
 
-/* Called by cgroups to determine if a cpuset is usable; cpuset_rwsem held */
+static void reset_migrate_dl_data(struct cpuset *cs)
+{
+	cs->nr_migrate_dl_tasks = 0;
+	cs->sum_migrate_dl_bw = 0;
+}
+
+/* Called by cgroups to determine if a cpuset is usable; cpuset_mutex held */
 static int cpuset_can_attach(struct cgroup_taskset *tset)
 {
 	struct cgroup_subsys_state *css;
-	struct cpuset *cs;
+	struct cpuset *cs, *oldcs;
 	struct task_struct *task;
 	int ret;
 
 	/* used later by cpuset_attach() */
 	cpuset_attach_old_cs = task_cs(cgroup_taskset_first(tset, &css));
+	oldcs = cpuset_attach_old_cs;
 	cs = css_cs(css);
 
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 
 	/* allow moving tasks into an empty cpuset if on default hierarchy */
 	ret = -ENOSPC;
@@ -2190,14 +2237,39 @@
 		goto out_unlock;
 
 	cgroup_taskset_for_each(task, css, tset) {
-		ret = task_can_attach(task, cs->cpus_allowed);
+		ret = task_can_attach(task);
 		if (ret)
 			goto out_unlock;
 		ret = security_task_setscheduler(task);
 		if (ret)
 			goto out_unlock;
+
+		if (dl_task(task)) {
+			cs->nr_migrate_dl_tasks++;
+			cs->sum_migrate_dl_bw += task->dl.dl_bw;
+		}
+	}
+
+	if (!cs->nr_migrate_dl_tasks)
+		goto out_success;
+
+	if (!cpumask_intersects(oldcs->effective_cpus, cs->effective_cpus)) {
+		int cpu = cpumask_any_and(cpu_active_mask, cs->effective_cpus);
+
+		if (unlikely(cpu >= nr_cpu_ids)) {
+			reset_migrate_dl_data(cs);
+			ret = -EINVAL;
+			goto out_unlock;
+		}
+
+		ret = dl_bw_alloc(cpu, cs->sum_migrate_dl_bw);
+		if (ret) {
+			reset_migrate_dl_data(cs);
+			goto out_unlock;
+		}
 	}
 
+out_success:
 	/*
 	 * Mark attach is in progress.  This makes validate_change() fail
 	 * changes which zero cpus/mems_allowed.
@@ -2205,23 +2277,35 @@
 	cs->attach_in_progress++;
 	ret = 0;
 out_unlock:
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	return ret;
 }
 
 static void cpuset_cancel_attach(struct cgroup_taskset *tset)
 {
 	struct cgroup_subsys_state *css;
+	struct cpuset *cs;
 
 	cgroup_taskset_first(tset, &css);
+	cs = css_cs(css);
+
+	mutex_lock(&cpuset_mutex);
+	cs->attach_in_progress--;
+	if (!cs->attach_in_progress)
+		wake_up(&cpuset_attach_wq);
+
+	if (cs->nr_migrate_dl_tasks) {
+		int cpu = cpumask_any(cs->effective_cpus);
+
+		dl_bw_free(cpu, cs->sum_migrate_dl_bw);
+		reset_migrate_dl_data(cs);
+	}
 
-	percpu_down_write(&cpuset_rwsem);
-	css_cs(css)->attach_in_progress--;
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 }
 
 /*
- * Protected by cpuset_rwsem.  cpus_attach is used only by cpuset_attach()
+ * Protected by cpuset_mutex.  cpus_attach is used only by cpuset_attach()
  * but we can't allocate it dynamically there.  Define it global and
  * allocate from cpuset_init().
  */
@@ -2229,18 +2313,35 @@
 
 static void cpuset_attach(struct cgroup_taskset *tset)
 {
-	/* static buf protected by cpuset_rwsem */
+	/* static buf protected by cpuset_mutex */
 	static nodemask_t cpuset_attach_nodemask_to;
 	struct task_struct *task;
 	struct task_struct *leader;
 	struct cgroup_subsys_state *css;
 	struct cpuset *cs;
 	struct cpuset *oldcs = cpuset_attach_old_cs;
+	bool cpus_updated, mems_updated;
 
 	cgroup_taskset_first(tset, &css);
 	cs = css_cs(css);
 
-	percpu_down_write(&cpuset_rwsem);
+	lockdep_assert_cpus_held();	/* see cgroup_attach_lock() */
+	mutex_lock(&cpuset_mutex);
+	cpus_updated = !cpumask_equal(cs->effective_cpus,
+				      oldcs->effective_cpus);
+	mems_updated = !nodes_equal(cs->effective_mems, oldcs->effective_mems);
+
+	/*
+	 * In the default hierarchy, enabling cpuset in the child cgroups
+	 * will trigger a number of cpuset_attach() calls with no change
+	 * in effective cpus and mems. In that case, we can optimize out
+	 * by skipping the task iteration and update.
+	 */
+	if (cgroup_subsys_on_dfl(cpuset_cgrp_subsys) &&
+	    !cpus_updated && !mems_updated) {
+		cpuset_attach_nodemask_to = cs->effective_mems;
+		goto out;
+	}
 
 	guarantee_online_mems(cs, &cpuset_attach_nodemask_to);
 
@@ -2261,9 +2362,14 @@
 
 	/*
 	 * Change mm for all threadgroup leaders. This is expensive and may
-	 * sleep and should be moved outside migration path proper.
+	 * sleep and should be moved outside migration path proper. Skip it
+	 * if there is no change in effective_mems and CS_MEMORY_MIGRATE is
+	 * not set.
 	 */
 	cpuset_attach_nodemask_to = cs->effective_mems;
+	if (!is_memory_migrate(cs) && !mems_updated)
+		goto out;
+
 	cgroup_taskset_for_each_leader(leader, css, tset) {
 		struct mm_struct *mm = get_task_mm(leader);
 
@@ -2286,13 +2392,20 @@
 		}
 	}
 
+out:
 	cs->old_mems_allowed = cpuset_attach_nodemask_to;
 
+	if (cs->nr_migrate_dl_tasks) {
+		cs->nr_deadline_tasks += cs->nr_migrate_dl_tasks;
+		oldcs->nr_deadline_tasks -= cs->nr_migrate_dl_tasks;
+		reset_migrate_dl_data(cs);
+	}
+
 	cs->attach_in_progress--;
 	if (!cs->attach_in_progress)
 		wake_up(&cpuset_attach_wq);
 
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 }
 
 /* The various types of files and directories in a cpuset file system */
@@ -2324,7 +2437,7 @@
 	int retval = 0;
 
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 	if (!is_cpuset_online(cs)) {
 		retval = -ENODEV;
 		goto out_unlock;
@@ -2360,7 +2473,7 @@
 		break;
 	}
 out_unlock:
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 	return retval;
 }
@@ -2373,7 +2486,7 @@
 	int retval = -ENODEV;
 
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 	if (!is_cpuset_online(cs))
 		goto out_unlock;
 
@@ -2386,7 +2499,7 @@
 		break;
 	}
 out_unlock:
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 	return retval;
 }
@@ -2419,7 +2532,7 @@
 	 * operation like this one can lead to a deadlock through kernfs
 	 * active_ref protection.  Let's break the protection.  Losing the
 	 * protection is okay as we check whether @cs is online after
-	 * grabbing cpuset_rwsem anyway.  This only happens on the legacy
+	 * grabbing cpuset_mutex anyway.  This only happens on the legacy
 	 * hierarchies.
 	 */
 	css_get(&cs->css);
@@ -2427,7 +2540,7 @@
 	flush_work(&cpuset_hotplug_work);
 
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 	if (!is_cpuset_online(cs))
 		goto out_unlock;
 
@@ -2451,7 +2564,7 @@
 
 	free_cpuset(trialcs);
 out_unlock:
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 	kernfs_unbreak_active_protection(of->kn);
 	css_put(&cs->css);
@@ -2584,13 +2697,13 @@
 
 	css_get(&cs->css);
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 	if (!is_cpuset_online(cs))
 		goto out_unlock;
 
 	retval = update_prstate(cs, val);
 out_unlock:
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 	css_put(&cs->css);
 	return retval ?: nbytes;
@@ -2803,7 +2916,7 @@
 		return 0;
 
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 
 	set_bit(CS_ONLINE, &cs->flags);
 	if (is_spread_page(parent))
@@ -2854,7 +2967,7 @@
 	cpumask_copy(cs->effective_cpus, parent->cpus_allowed);
 	spin_unlock_irq(&callback_lock);
 out_unlock:
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 	return 0;
 }
@@ -2875,7 +2988,7 @@
 	struct cpuset *cs = css_cs(css);
 
 	cpus_read_lock();
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 
 	if (is_partition_root(cs))
 		update_prstate(cs, 0);
@@ -2894,7 +3007,7 @@
 	cpuset_dec();
 	clear_bit(CS_ONLINE, &cs->flags);
 
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 	cpus_read_unlock();
 }
 
@@ -2907,7 +3020,7 @@
 
 static void cpuset_bind(struct cgroup_subsys_state *root_css)
 {
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 	spin_lock_irq(&callback_lock);
 
 	if (is_in_v2_mode()) {
@@ -2920,7 +3033,7 @@
 	}
 
 	spin_unlock_irq(&callback_lock);
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 }
 
 /*
@@ -2962,8 +3075,6 @@
 
 int __init cpuset_init(void)
 {
-	BUG_ON(percpu_init_rwsem(&cpuset_rwsem));
-
 	BUG_ON(!alloc_cpumask_var(&top_cpuset.cpus_allowed, GFP_KERNEL));
 	BUG_ON(!alloc_cpumask_var(&top_cpuset.effective_cpus, GFP_KERNEL));
 	BUG_ON(!zalloc_cpumask_var(&top_cpuset.subparts_cpus, GFP_KERNEL));
@@ -3035,7 +3146,7 @@
 	is_empty = cpumask_empty(cs->cpus_allowed) ||
 		   nodes_empty(cs->mems_allowed);
 
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 
 	/*
 	 * Move tasks to the nearest ancestor with execution resources,
@@ -3045,7 +3156,7 @@
 	if (is_empty)
 		remove_tasks_in_empty_cpuset(cs);
 
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 }
 
 static void
@@ -3095,14 +3206,14 @@
 retry:
 	wait_event(cpuset_attach_wq, cs->attach_in_progress == 0);
 
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 
 	/*
 	 * We have raced with task attaching. We wait until attaching
 	 * is finished, so we won't attach a task to an empty cpuset.
 	 */
 	if (cs->attach_in_progress) {
-		percpu_up_write(&cpuset_rwsem);
+		mutex_unlock(&cpuset_mutex);
 		goto retry;
 	}
 
@@ -3180,7 +3291,7 @@
 		hotplug_update_tasks_legacy(cs, &new_cpus, &new_mems,
 					    cpus_updated, mems_updated);
 
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 }
 
 /**
@@ -3210,7 +3321,7 @@
 	if (on_dfl && !alloc_cpumasks(NULL, &tmp))
 		ptmp = &tmp;
 
-	percpu_down_write(&cpuset_rwsem);
+	mutex_lock(&cpuset_mutex);
 
 	/* fetch the available cpus/mems and find out which changed how */
 	cpumask_copy(&new_cpus, cpu_active_mask);
@@ -3267,7 +3378,7 @@
 		update_tasks_nodemask(&top_cpuset);
 	}
 
-	percpu_up_write(&cpuset_rwsem);
+	mutex_unlock(&cpuset_mutex);
 
 	/* if cpus or mems changed, we need to propagate to descendants */
 	if (cpus_updated || mems_updated) {
@@ -3336,8 +3447,11 @@
  */
 void __init cpuset_init_smp(void)
 {
-	cpumask_copy(top_cpuset.cpus_allowed, cpu_active_mask);
-	top_cpuset.mems_allowed = node_states[N_MEMORY];
+	/*
+	 * cpus_allowd/mems_allowed set to v2 values in the initial
+	 * cpuset_bind() call will be reset to v1 values in another
+	 * cpuset_bind() call when v1 cpuset is mounted.
+	 */
 	top_cpuset.old_mems_allowed = top_cpuset.mems_allowed;
 
 	cpumask_copy(top_cpuset.effective_cpus, cpu_active_mask);
@@ -3674,7 +3788,7 @@
  *  - Used for /proc/<pid>/cpuset.
  *  - No need to task_lock(tsk) on this tsk->cpuset reference, as it
  *    doesn't really matter if tsk->cpuset changes after we read it,
- *    and we take cpuset_rwsem, keeping cpuset_attach() from changing it
+ *    and we take cpuset_mutex, keeping cpuset_attach() from changing it
  *    anyway.
  */
 int proc_cpuset_show(struct seq_file *m, struct pid_namespace *ns,
@@ -3689,10 +3803,14 @@
 	if (!buf)
 		goto out;
 
-	css = task_get_css(tsk, cpuset_cgrp_id);
-	retval = cgroup_path_ns(css->cgroup, buf, PATH_MAX,
-				current->nsproxy->cgroup_ns);
-	css_put(css);
+	rcu_read_lock();
+	spin_lock_irq(&css_set_lock);
+	css = task_css(tsk, cpuset_cgrp_id);
+	retval = cgroup_path_ns_locked(css->cgroup, buf, PATH_MAX,
+				       current->nsproxy->cgroup_ns);
+	spin_unlock_irq(&css_set_lock);
+	rcu_read_unlock();
+
 	if (retval >= PATH_MAX)
 		retval = -ENAMETOOLONG;
 	if (retval < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cgroup/namespace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cgroup/namespace.c
@@ -149,9 +149,3 @@
 	.install	= cgroupns_install,
 	.owner		= cgroupns_owner,
 };
-
-static __init int cgroup_namespaces_init(void)
-{
-	return 0;
-}
-subsys_initcall(cgroup_namespaces_init);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cgroup/rstat.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cgroup/rstat.c
@@ -433,8 +433,6 @@
 		cputime->sum_exec_runtime += user;
 		cputime->sum_exec_runtime += sys;
 		cputime->sum_exec_runtime += cpustat[CPUTIME_STEAL];
-		cputime->sum_exec_runtime += cpustat[CPUTIME_GUEST];
-		cputime->sum_exec_runtime += cpustat[CPUTIME_GUEST_NICE];
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/compat.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/compat.c
@@ -152,7 +152,7 @@
 	if (len & (sizeof(compat_ulong_t)-1))
 		return -EINVAL;
 
-	if (!alloc_cpumask_var(&mask, GFP_KERNEL))
+	if (!zalloc_cpumask_var(&mask, GFP_KERNEL))
 		return -ENOMEM;
 
 	ret = sched_getaffinity(pid, mask);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cpu.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cpu.c
@@ -31,8 +31,10 @@
 #include <linux/smpboot.h>
 #include <linux/relay.h>
 #include <linux/slab.h>
+#include <linux/scs.h>
 #include <linux/percpu-rwsem.h>
 #include <linux/cpuset.h>
+#include <linux/random.h>
 
 #include <trace/events/power.h>
 #define CREATE_TRACE_POINTS
@@ -69,7 +71,6 @@
 	bool			rollback;
 	bool			single;
 	bool			bringup;
-	int			cpu;
 	struct hlist_node	*node;
 	struct hlist_node	*last;
 	enum cpuhp_state	cb_state;
@@ -473,7 +474,7 @@
 #endif
 
 static inline enum cpuhp_state
-cpuhp_set_state(struct cpuhp_cpu_state *st, enum cpuhp_state target)
+cpuhp_set_state(int cpu, struct cpuhp_cpu_state *st, enum cpuhp_state target)
 {
 	enum cpuhp_state prev_state = st->state;
 	bool bringup = st->state < target;
@@ -484,14 +485,15 @@
 	st->target = target;
 	st->single = false;
 	st->bringup = bringup;
-	if (cpu_dying(st->cpu) != !bringup)
-		set_cpu_dying(st->cpu, !bringup);
+	if (cpu_dying(cpu) != !bringup)
+		set_cpu_dying(cpu, !bringup);
 
 	return prev_state;
 }
 
 static inline void
-cpuhp_reset_state(struct cpuhp_cpu_state *st, enum cpuhp_state prev_state)
+cpuhp_reset_state(int cpu, struct cpuhp_cpu_state *st,
+		  enum cpuhp_state prev_state)
 {
 	bool bringup = !st->bringup;
 
@@ -518,8 +520,8 @@
 	}
 
 	st->bringup = bringup;
-	if (cpu_dying(st->cpu) != !bringup)
-		set_cpu_dying(st->cpu, !bringup);
+	if (cpu_dying(cpu) != !bringup)
+		set_cpu_dying(cpu, !bringup);
 }
 
 /* Regular hotplug invocation of the AP hotplug thread */
@@ -539,15 +541,16 @@
 	wait_for_ap_thread(st, st->bringup);
 }
 
-static int cpuhp_kick_ap(struct cpuhp_cpu_state *st, enum cpuhp_state target)
+static int cpuhp_kick_ap(int cpu, struct cpuhp_cpu_state *st,
+			 enum cpuhp_state target)
 {
 	enum cpuhp_state prev_state;
 	int ret;
 
-	prev_state = cpuhp_set_state(st, target);
+	prev_state = cpuhp_set_state(cpu, st, target);
 	__cpuhp_kick_ap(st);
 	if ((ret = st->result)) {
-		cpuhp_reset_state(st, prev_state);
+		cpuhp_reset_state(cpu, st, prev_state);
 		__cpuhp_kick_ap(st);
 	}
 
@@ -579,7 +582,7 @@
 	if (st->target <= CPUHP_AP_ONLINE_IDLE)
 		return 0;
 
-	return cpuhp_kick_ap(st, st->target);
+	return cpuhp_kick_ap(cpu, st, st->target);
 }
 
 static int bringup_cpu(unsigned int cpu)
@@ -588,6 +591,12 @@
 	int ret;
 
 	/*
+	 * Reset stale stack state from the last time this CPU was online.
+	 */
+	scs_task_reset(idle);
+	kasan_unpoison_task_stack(idle);
+
+	/*
 	 * Some architectures have to walk the irq descriptors to
 	 * setup the vector space for the cpu which comes online.
 	 * Prevent irq alloc/free across the bringup.
@@ -653,21 +662,51 @@
 	return true;
 }
 
-static int cpuhp_invoke_callback_range(bool bringup,
-				       unsigned int cpu,
-				       struct cpuhp_cpu_state *st,
-				       enum cpuhp_state target)
+static int __cpuhp_invoke_callback_range(bool bringup,
+					 unsigned int cpu,
+					 struct cpuhp_cpu_state *st,
+					 enum cpuhp_state target,
+					 bool nofail)
 {
 	enum cpuhp_state state;
-	int err = 0;
+	int ret = 0;
 
 	while (cpuhp_next_state(bringup, &state, st, target)) {
+		int err;
+
 		err = cpuhp_invoke_callback(cpu, state, bringup, NULL, NULL);
-		if (err)
+		if (!err)
+			continue;
+
+		if (nofail) {
+			pr_warn("CPU %u %s state %s (%d) failed (%d)\n",
+				cpu, bringup ? "UP" : "DOWN",
+				cpuhp_get_step(st->state)->name,
+				st->state, err);
+			ret = -1;
+		} else {
+			ret = err;
 			break;
+		}
 	}
 
-	return err;
+	return ret;
+}
+
+static inline int cpuhp_invoke_callback_range(bool bringup,
+					      unsigned int cpu,
+					      struct cpuhp_cpu_state *st,
+					      enum cpuhp_state target)
+{
+	return __cpuhp_invoke_callback_range(bringup, cpu, st, target, false);
+}
+
+static inline void cpuhp_invoke_callback_range_nofail(bool bringup,
+						      unsigned int cpu,
+						      struct cpuhp_cpu_state *st,
+						      enum cpuhp_state target)
+{
+	__cpuhp_invoke_callback_range(bringup, cpu, st, target, true);
 }
 
 static inline bool can_rollback_cpu(struct cpuhp_cpu_state *st)
@@ -696,7 +735,7 @@
 			 ret, cpu, cpuhp_get_step(st->state)->name,
 			 st->state);
 
-		cpuhp_reset_state(st, prev_state);
+		cpuhp_reset_state(cpu, st, prev_state);
 		if (can_rollback_cpu(st))
 			WARN_ON(cpuhp_invoke_callback_range(false, cpu, st,
 							    prev_state));
@@ -713,7 +752,6 @@
 
 	init_completion(&st->done_up);
 	init_completion(&st->done_down);
-	st->cpu = cpu;
 }
 
 static int cpuhp_should_run(unsigned int cpu)
@@ -867,7 +905,7 @@
 	cpuhp_lock_release(true);
 
 	trace_cpuhp_enter(cpu, st->target, prev_state, cpuhp_kick_ap_work);
-	ret = cpuhp_kick_ap(st, st->target);
+	ret = cpuhp_kick_ap(cpu, st, st->target);
 	trace_cpuhp_exit(cpu, st->state, prev_state, ret);
 
 	return ret;
@@ -986,7 +1024,6 @@
 	struct cpuhp_cpu_state *st = this_cpu_ptr(&cpuhp_state);
 	enum cpuhp_state target = max((int)st->target, CPUHP_AP_OFFLINE);
 	int err, cpu = smp_processor_id();
-	int ret;
 
 	/* Ensure this CPU doesn't handle any more interrupts. */
 	err = __cpu_disable();
@@ -999,13 +1036,10 @@
 	 */
 	WARN_ON(st->state != (CPUHP_TEARDOWN_CPU - 1));
 
-	/* Invoke the former CPU_DYING callbacks */
-	ret = cpuhp_invoke_callback_range(false, cpu, st, target);
-
 	/*
-	 * DYING must not fail!
+	 * Invoke the former CPU_DYING callbacks. DYING must not fail!
 	 */
-	WARN_ON_ONCE(ret);
+	cpuhp_invoke_callback_range_nofail(false, cpu, st, target);
 
 	/* Give up timekeeping duties */
 	tick_handover_do_timer();
@@ -1099,7 +1133,7 @@
 			 ret, cpu, cpuhp_get_step(st->state)->name,
 			 st->state);
 
-		cpuhp_reset_state(st, prev_state);
+		cpuhp_reset_state(cpu, st, prev_state);
 
 		if (st->state < prev_state)
 			WARN_ON(cpuhp_invoke_callback_range(true, cpu, st,
@@ -1126,7 +1160,7 @@
 
 	cpuhp_tasks_frozen = tasks_frozen;
 
-	prev_state = cpuhp_set_state(st, target);
+	prev_state = cpuhp_set_state(cpu, st, target);
 	/*
 	 * If the current CPU state is in the range of the AP hotplug thread,
 	 * then we need to kick the thread.
@@ -1157,7 +1191,7 @@
 	ret = cpuhp_down_callbacks(cpu, st, target);
 	if (ret && st->state < prev_state) {
 		if (st->state == CPUHP_TEARDOWN_CPU) {
-			cpuhp_reset_state(st, prev_state);
+			cpuhp_reset_state(cpu, st, prev_state);
 			__cpuhp_kick_ap(st);
 		} else {
 			WARN(1, "DEAD callback error for CPU%d", cpu);
@@ -1277,16 +1311,14 @@
 {
 	struct cpuhp_cpu_state *st = per_cpu_ptr(&cpuhp_state, cpu);
 	enum cpuhp_state target = min((int)st->target, CPUHP_AP_ONLINE);
-	int ret;
 
 	rcu_cpu_starting(cpu);	/* Enables RCU usage on this CPU. */
 	cpumask_set_cpu(cpu, &cpus_booted_once_mask);
-	ret = cpuhp_invoke_callback_range(true, cpu, st, target);
 
 	/*
 	 * STARTING must not fail!
 	 */
-	WARN_ON_ONCE(ret);
+	cpuhp_invoke_callback_range_nofail(true, cpu, st, target);
 }
 
 /*
@@ -1344,7 +1376,7 @@
 
 	cpuhp_tasks_frozen = tasks_frozen;
 
-	cpuhp_set_state(st, target);
+	cpuhp_set_state(cpu, st, target);
 	/*
 	 * If the current CPU state is in the range of the AP hotplug thread,
 	 * then we need to kick the thread once more.
@@ -1652,6 +1684,11 @@
 		.startup.single		= perf_event_init_cpu,
 		.teardown.single	= perf_event_exit_cpu,
 	},
+	[CPUHP_RANDOM_PREPARE] = {
+		.name			= "random:prepare",
+		.startup.single		= random_prepare_cpu,
+		.teardown.single	= NULL,
+	},
 	[CPUHP_WORKQUEUE_PREP] = {
 		.name			= "workqueue:prepare",
 		.startup.single		= workqueue_prepare_cpu,
@@ -1660,7 +1697,7 @@
 	[CPUHP_HRTIMERS_PREPARE] = {
 		.name			= "hrtimers:prepare",
 		.startup.single		= hrtimers_prepare_cpu,
-		.teardown.single	= hrtimers_dead_cpu,
+		.teardown.single	= NULL,
 	},
 	[CPUHP_SMPCFD_PREPARE] = {
 		.name			= "smpcfd:prepare",
@@ -1727,6 +1764,12 @@
 		.startup.single		= NULL,
 		.teardown.single	= smpcfd_dying_cpu,
 	},
+	[CPUHP_AP_HRTIMERS_DYING] = {
+		.name			= "hrtimers:dying",
+		.startup.single		= hrtimers_cpu_starting,
+		.teardown.single	= hrtimers_cpu_dying,
+	},
+
 	/* Entry state on starting. Interrupts enabled from here on. Transient
 	 * state for synchronsization */
 	[CPUHP_AP_ONLINE] = {
@@ -1775,6 +1818,11 @@
 		.startup.single		= workqueue_online_cpu,
 		.teardown.single	= workqueue_offline_cpu,
 	},
+	[CPUHP_AP_RANDOM_ONLINE] = {
+		.name			= "random:online",
+		.startup.single		= random_online_cpu,
+		.teardown.single	= NULL,
+	},
 	[CPUHP_AP_RCUTREE_ONLINE] = {
 		.name			= "RCU/tree:online",
 		.startup.single		= rcutree_online_cpu,
@@ -2010,7 +2058,7 @@
  * The caller needs to hold cpus read locked while calling this function.
  * Return:
  *   On success:
- *      Positive state number if @state is CPUHP_AP_ONLINE_DYN;
+ *      Positive state number if @state is CPUHP_AP_ONLINE_DYN or CPUHP_BP_PREPARE_DYN;
  *      0 for all other states
  *   On failure: proper (negative) error code
  */
@@ -2033,7 +2081,7 @@
 	ret = cpuhp_store_callbacks(state, name, startup, teardown,
 				    multi_instance);
 
-	dynstate = state == CPUHP_AP_ONLINE_DYN;
+	dynstate = state == CPUHP_AP_ONLINE_DYN || state == CPUHP_BP_PREPARE_DYN;
 	if (ret > 0 && dynstate) {
 		state = ret;
 		ret = 0;
@@ -2064,8 +2112,8 @@
 out:
 	mutex_unlock(&cpuhp_state_mutex);
 	/*
-	 * If the requested state is CPUHP_AP_ONLINE_DYN, return the
-	 * dynamically allocated state in case of success.
+	 * If the requested state is CPUHP_AP_ONLINE_DYN or CPUHP_BP_PREPARE_DYN,
+	 * return the dynamically allocated state in case of success.
 	 */
 	if (!ret && dynstate)
 		return state;
@@ -2297,8 +2345,10 @@
 
 	if (st->state < target)
 		ret = cpu_up(dev->id, target);
-	else
+	else if (st->state > target)
 		ret = cpu_down(dev->id, target);
+	else if (WARN_ON(st->target != target))
+		st->target = target;
 out:
 	unlock_device_hotplug();
 	return ret ? ret : count;
@@ -2672,7 +2722,8 @@
 };
 
 static enum cpu_mitigations cpu_mitigations __ro_after_init =
-	CPU_MITIGATIONS_AUTO;
+	IS_ENABLED(CONFIG_CPU_MITIGATIONS) ? CPU_MITIGATIONS_AUTO :
+					     CPU_MITIGATIONS_OFF;
 
 static int __init mitigations_parse_cmdline(char *arg)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/crash_core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/crash_core.c
@@ -6,6 +6,7 @@
 
 #include <linux/buildid.h>
 #include <linux/crash_core.h>
+#include <linux/init.h>
 #include <linux/utsname.h>
 #include <linux/vmalloc.h>
 
@@ -295,6 +296,16 @@
 				"crashkernel=", suffix_tbl[SUFFIX_LOW]);
 }
 
+/*
+ * Add a dummy early_param handler to mark crashkernel= as a known command line
+ * parameter and suppress incorrect warnings in init/main.c.
+ */
+static int __init parse_crashkernel_dummy(char *arg)
+{
+	return 0;
+}
+early_param("crashkernel", parse_crashkernel_dummy);
+
 Elf_Word *append_elf_note(Elf_Word *buf, char *name, unsigned int type,
 			  void *data, size_t data_len)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/cred.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/cred.c
@@ -99,17 +99,17 @@
 
 #ifdef CONFIG_DEBUG_CREDENTIALS
 	if (cred->magic != CRED_MAGIC_DEAD ||
-	    atomic_read(&cred->usage) != 0 ||
+	    atomic_long_read(&cred->usage) != 0 ||
 	    read_cred_subscribers(cred) != 0)
 		panic("CRED: put_cred_rcu() sees %p with"
-		      " mag %x, put %p, usage %d, subscr %d\n",
+		      " mag %x, put %p, usage %ld, subscr %d\n",
 		      cred, cred->magic, cred->put_addr,
-		      atomic_read(&cred->usage),
+		      atomic_long_read(&cred->usage),
 		      read_cred_subscribers(cred));
 #else
-	if (atomic_read(&cred->usage) != 0)
-		panic("CRED: put_cred_rcu() sees %p with usage %d\n",
-		      cred, atomic_read(&cred->usage));
+	if (atomic_long_read(&cred->usage) != 0)
+		panic("CRED: put_cred_rcu() sees %p with usage %ld\n",
+		      cred, atomic_long_read(&cred->usage));
 #endif
 
 	security_cred_free(cred);
@@ -134,11 +134,11 @@
  */
 void __put_cred(struct cred *cred)
 {
-	kdebug("__put_cred(%p{%d,%d})", cred,
-	       atomic_read(&cred->usage),
+	kdebug("__put_cred(%p{%ld,%d})", cred,
+	       atomic_long_read(&cred->usage),
 	       read_cred_subscribers(cred));
 
-	BUG_ON(atomic_read(&cred->usage) != 0);
+	BUG_ON(atomic_long_read(&cred->usage) != 0);
 #ifdef CONFIG_DEBUG_CREDENTIALS
 	BUG_ON(read_cred_subscribers(cred) != 0);
 	cred->magic = CRED_MAGIC_DEAD;
@@ -161,8 +161,8 @@
 {
 	struct cred *cred;
 
-	kdebug("exit_creds(%u,%p,%p,{%d,%d})", tsk->pid, tsk->real_cred, tsk->cred,
-	       atomic_read(&tsk->cred->usage),
+	kdebug("exit_creds(%u,%p,%p,{%ld,%d})", tsk->pid, tsk->real_cred, tsk->cred,
+	       atomic_long_read(&tsk->cred->usage),
 	       read_cred_subscribers(tsk->cred));
 
 	cred = (struct cred *) tsk->real_cred;
@@ -221,7 +221,7 @@
 	if (!new)
 		return NULL;
 
-	atomic_set(&new->usage, 1);
+	atomic_long_set(&new->usage, 1);
 #ifdef CONFIG_DEBUG_CREDENTIALS
 	new->magic = CRED_MAGIC;
 #endif
@@ -267,7 +267,7 @@
 	memcpy(new, old, sizeof(struct cred));
 
 	new->non_rcu = 0;
-	atomic_set(&new->usage, 1);
+	atomic_long_set(&new->usage, 1);
 	set_cred_subscribers(new, 0);
 	get_group_info(new->group_info);
 	get_uid(new->user);
@@ -355,8 +355,8 @@
 		p->real_cred = get_cred(p->cred);
 		get_cred(p->cred);
 		alter_cred_subscribers(p->cred, 2);
-		kdebug("share_creds(%p{%d,%d})",
-		       p->cred, atomic_read(&p->cred->usage),
+		kdebug("share_creds(%p{%ld,%d})",
+		       p->cred, atomic_long_read(&p->cred->usage),
 		       read_cred_subscribers(p->cred));
 		inc_rlimit_ucounts(task_ucounts(p), UCOUNT_RLIMIT_NPROC, 1);
 		return 0;
@@ -449,8 +449,8 @@
 	struct task_struct *task = current;
 	const struct cred *old = task->real_cred;
 
-	kdebug("commit_creds(%p{%d,%d})", new,
-	       atomic_read(&new->usage),
+	kdebug("commit_creds(%p{%ld,%d})", new,
+	       atomic_long_read(&new->usage),
 	       read_cred_subscribers(new));
 
 	BUG_ON(task->cred != old);
@@ -459,7 +459,7 @@
 	validate_creds(old);
 	validate_creds(new);
 #endif
-	BUG_ON(atomic_read(&new->usage) < 1);
+	BUG_ON(atomic_long_read(&new->usage) < 1);
 
 	get_cred(new); /* we will require a ref for the subj creds too */
 
@@ -532,14 +532,14 @@
  */
 void abort_creds(struct cred *new)
 {
-	kdebug("abort_creds(%p{%d,%d})", new,
-	       atomic_read(&new->usage),
+	kdebug("abort_creds(%p{%ld,%d})", new,
+	       atomic_long_read(&new->usage),
 	       read_cred_subscribers(new));
 
 #ifdef CONFIG_DEBUG_CREDENTIALS
 	BUG_ON(read_cred_subscribers(new) != 0);
 #endif
-	BUG_ON(atomic_read(&new->usage) < 1);
+	BUG_ON(atomic_long_read(&new->usage) < 1);
 	put_cred(new);
 }
 EXPORT_SYMBOL(abort_creds);
@@ -555,8 +555,8 @@
 {
 	const struct cred *old = current->cred;
 
-	kdebug("override_creds(%p{%d,%d})", new,
-	       atomic_read(&new->usage),
+	kdebug("override_creds(%p{%ld,%d})", new,
+	       atomic_long_read(&new->usage),
 	       read_cred_subscribers(new));
 
 	validate_creds(old);
@@ -578,8 +578,8 @@
 	rcu_assign_pointer(current->cred, new);
 	alter_cred_subscribers(old, -1);
 
-	kdebug("override_creds() = %p{%d,%d}", old,
-	       atomic_read(&old->usage),
+	kdebug("override_creds() = %p{%ld,%d}", old,
+	       atomic_long_read(&old->usage),
 	       read_cred_subscribers(old));
 	return old;
 }
@@ -596,8 +596,8 @@
 {
 	const struct cred *override = current->cred;
 
-	kdebug("revert_creds(%p{%d,%d})", old,
-	       atomic_read(&old->usage),
+	kdebug("revert_creds(%p{%ld,%d})", old,
+	       atomic_long_read(&old->usage),
 	       read_cred_subscribers(old));
 
 	validate_creds(old);
@@ -665,26 +665,20 @@
 
 int set_cred_ucounts(struct cred *new)
 {
-	struct task_struct *task = current;
-	const struct cred *old = task->real_cred;
 	struct ucounts *new_ucounts, *old_ucounts = new->ucounts;
 
-	if (new->user == old->user && new->user_ns == old->user_ns)
-		return 0;
-
 	/*
 	 * This optimization is needed because alloc_ucounts() uses locks
 	 * for table lookups.
 	 */
-	if (old_ucounts && old_ucounts->ns == new->user_ns && uid_eq(old_ucounts->uid, new->euid))
+	if (old_ucounts->ns == new->user_ns && uid_eq(old_ucounts->uid, new->uid))
 		return 0;
 
-	if (!(new_ucounts = alloc_ucounts(new->user_ns, new->euid)))
+	if (!(new_ucounts = alloc_ucounts(new->user_ns, new->uid)))
 		return -EAGAIN;
 
 	new->ucounts = new_ucounts;
-	if (old_ucounts)
-		put_ucounts(old_ucounts);
+	put_ucounts(old_ucounts);
 
 	return 0;
 }
@@ -735,7 +729,7 @@
 
 	*new = *old;
 	new->non_rcu = 0;
-	atomic_set(&new->usage, 1);
+	atomic_long_set(&new->usage, 1);
 	set_cred_subscribers(new, 0);
 	get_uid(new->user);
 	get_user_ns(new->user_ns);
@@ -773,14 +767,14 @@
 /**
  * set_security_override - Set the security ID in a set of credentials
  * @new: The credentials to alter
- * @secid: The LSM security ID to set
+ * @blob: The LSM security information to set
  *
  * Set the LSM security ID in a set of credentials so that the subjective
  * security is overridden when an alternative set of credentials is used.
  */
-int set_security_override(struct cred *new, u32 secid)
+int set_security_override(struct cred *new, struct lsmblob *blob)
 {
-	return security_kernel_act_as(new, secid);
+	return security_kernel_act_as(new, blob);
 }
 EXPORT_SYMBOL(set_security_override);
 
@@ -796,14 +790,14 @@
  */
 int set_security_override_from_ctx(struct cred *new, const char *secctx)
 {
-	u32 secid;
+	struct lsmblob blob;
 	int ret;
 
-	ret = security_secctx_to_secid(secctx, strlen(secctx), &secid);
+	ret = security_secctx_to_secid(secctx, strlen(secctx), &blob);
 	if (ret < 0)
 		return ret;
 
-	return set_security_override(new, secid);
+	return set_security_override(new, &blob);
 }
 EXPORT_SYMBOL(set_security_override_from_ctx);
 
@@ -849,8 +843,8 @@
 	       cred == tsk->cred ? "[eff]" : "");
 	printk(KERN_ERR "CRED: ->magic=%x, put_addr=%p\n",
 	       cred->magic, cred->put_addr);
-	printk(KERN_ERR "CRED: ->usage=%d, subscr=%d\n",
-	       atomic_read(&cred->usage),
+	printk(KERN_ERR "CRED: ->usage=%ld, subscr=%d\n",
+	       atomic_long_read(&cred->usage),
 	       read_cred_subscribers(cred));
 	printk(KERN_ERR "CRED: ->*uid = { %d,%d,%d,%d }\n",
 		from_kuid_munged(&init_user_ns, cred->uid),
@@ -922,9 +916,9 @@
  */
 void validate_creds_for_do_exit(struct task_struct *tsk)
 {
-	kdebug("validate_creds_for_do_exit(%p,%p{%d,%d})",
+	kdebug("validate_creds_for_do_exit(%p,%p{%ld,%d})",
 	       tsk->real_cred, tsk->cred,
-	       atomic_read(&tsk->cred->usage),
+	       atomic_long_read(&tsk->cred->usage),
 	       read_cred_subscribers(tsk->cred));
 
 	__validate_process_creds(tsk, __FILE__, __LINE__);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/debug/debug_core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/debug/debug_core.c
@@ -53,6 +53,7 @@
 #include <linux/vmacache.h>
 #include <linux/rcupdate.h>
 #include <linux/irq.h>
+#include <linux/security.h>
 
 #include <asm/cacheflush.h>
 #include <asm/byteorder.h>
@@ -745,6 +746,8 @@
 
 	while (1) {
 cpu_master_loop:
+		if (security_locked_down(LOCKDOWN_KGDB))
+			break;
 		if (dbg_kdb_mode) {
 			kgdb_connected = 1;
 			error = kdb_stub(ks);
@@ -994,6 +997,9 @@
 	if (panic_timeout)
 		return;
 
+	debug_locks_off();
+	console_flush_on_panic(CONSOLE_FLUSH_PENDING);
+
 	if (dbg_kdb_mode)
 		kdb_printf("PANIC: %s\n", msg);
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/debug/kdb/kdb_bt.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/debug/kdb/kdb_bt.c
@@ -46,7 +46,7 @@
  *	btp <pid>			Kernel stack for <pid>
  *	btt <address-expression>	Kernel stack for task structure at
  *					<address-expression>
- *	bta [DRSTCZEUIMA]		All useful processes, optionally
+ *	bta [state_chars>|A]		All useful processes, optionally
  *					filtered by state
  *	btc [<cpu>]			The current process on one cpu,
  *					default is all cpus
@@ -74,7 +74,7 @@
  */
 
 static int
-kdb_bt1(struct task_struct *p, unsigned long mask, bool btaprompt)
+kdb_bt1(struct task_struct *p, const char *mask, bool btaprompt)
 {
 	char ch;
 
@@ -120,7 +120,7 @@
 		return;
 	}
 
-	kdb_bt1(kdb_tsk, ~0UL, false);
+	kdb_bt1(kdb_tsk, "A", false);
 }
 
 int
@@ -138,8 +138,8 @@
 	if (strcmp(argv[0], "bta") == 0) {
 		struct task_struct *g, *p;
 		unsigned long cpu;
-		unsigned long mask = kdb_task_state_string(argc ? argv[1] :
-							   NULL);
+		const char *mask = argc ? argv[1] : kdbgetenv("PS");
+
 		if (argc == 0)
 			kdb_ps_suppressed();
 		/* Run the active tasks first */
@@ -167,7 +167,7 @@
 			return diag;
 		p = find_task_by_pid_ns(pid, &init_pid_ns);
 		if (p)
-			return kdb_bt1(p, ~0UL, false);
+			return kdb_bt1(p, "A", false);
 		kdb_printf("No process with pid == %ld found\n", pid);
 		return 0;
 	} else if (strcmp(argv[0], "btt") == 0) {
@@ -176,7 +176,7 @@
 		diag = kdbgetularg((char *)argv[1], &addr);
 		if (diag)
 			return diag;
-		return kdb_bt1((struct task_struct *)addr, ~0UL, false);
+		return kdb_bt1((struct task_struct *)addr, "A", false);
 	} else if (strcmp(argv[0], "btc") == 0) {
 		unsigned long cpu = ~0;
 		if (argc > 1)
@@ -212,7 +212,7 @@
 			kdb_show_stack(kdb_current_task, (void *)addr);
 			return 0;
 		} else {
-			return kdb_bt1(kdb_current_task, ~0UL, false);
+			return kdb_bt1(kdb_current_task, "A", false);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/debug/kdb/kdb_io.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/debug/kdb/kdb_io.c
@@ -172,6 +172,33 @@
 	unreachable();
 }
 
+/**
+ * kdb_position_cursor() - Place cursor in the correct horizontal position
+ * @prompt: Nil-terminated string containing the prompt string
+ * @buffer: Nil-terminated string containing the entire command line
+ * @cp: Cursor position, pointer the character in buffer where the cursor
+ *      should be positioned.
+ *
+ * The cursor is positioned by sending a carriage-return and then printing
+ * the content of the line until we reach the correct cursor position.
+ *
+ * There is some additional fine detail here.
+ *
+ * Firstly, even though kdb_printf() will correctly format zero-width fields
+ * we want the second call to kdb_printf() to be conditional. That keeps things
+ * a little cleaner when LOGGING=1.
+ *
+ * Secondly, we can't combine everything into one call to kdb_printf() since
+ * that renders into a fixed length buffer and the combined print could result
+ * in unwanted truncation.
+ */
+static void kdb_position_cursor(char *prompt, char *buffer, char *cp)
+{
+	kdb_printf("\r%s", prompt);
+	if (cp > buffer)
+		kdb_printf("%.*s", (int)(cp - buffer), buffer);
+}
+
 /*
  * kdb_read
  *
@@ -200,7 +227,6 @@
 						 * and null byte */
 	char *lastchar;
 	char *p_tmp;
-	char tmp;
 	static char tmpbuffer[CMD_BUFLEN];
 	int len = strlen(buffer);
 	int len_tmp;
@@ -237,12 +263,8 @@
 			}
 			*(--lastchar) = '\0';
 			--cp;
-			kdb_printf("\b%s \r", cp);
-			tmp = *cp;
-			*cp = '\0';
-			kdb_printf(kdb_prompt_str);
-			kdb_printf("%s", buffer);
-			*cp = tmp;
+			kdb_printf("\b%s ", cp);
+			kdb_position_cursor(kdb_prompt_str, buffer, cp);
 		}
 		break;
 	case 13: /* enter */
@@ -259,19 +281,14 @@
 			memcpy(tmpbuffer, cp+1, lastchar - cp - 1);
 			memcpy(cp, tmpbuffer, lastchar - cp - 1);
 			*(--lastchar) = '\0';
-			kdb_printf("%s \r", cp);
-			tmp = *cp;
-			*cp = '\0';
-			kdb_printf(kdb_prompt_str);
-			kdb_printf("%s", buffer);
-			*cp = tmp;
+			kdb_printf("%s ", cp);
+			kdb_position_cursor(kdb_prompt_str, buffer, cp);
 		}
 		break;
 	case 1: /* Home */
 		if (cp > buffer) {
-			kdb_printf("\r");
-			kdb_printf(kdb_prompt_str);
 			cp = buffer;
+			kdb_position_cursor(kdb_prompt_str, buffer, cp);
 		}
 		break;
 	case 5: /* End */
@@ -287,11 +304,10 @@
 		}
 		break;
 	case 14: /* Down */
-		memset(tmpbuffer, ' ',
-		       strlen(kdb_prompt_str) + (lastchar-buffer));
-		*(tmpbuffer+strlen(kdb_prompt_str) +
-		  (lastchar-buffer)) = '\0';
-		kdb_printf("\r%s\r", tmpbuffer);
+	case 16: /* Up */
+		kdb_printf("\r%*c\r",
+			   (int)(strlen(kdb_prompt_str) + (lastchar - buffer)),
+			   ' ');
 		*lastchar = (char)key;
 		*(lastchar+1) = '\0';
 		return lastchar;
@@ -301,15 +317,6 @@
 			++cp;
 		}
 		break;
-	case 16: /* Up */
-		memset(tmpbuffer, ' ',
-		       strlen(kdb_prompt_str) + (lastchar-buffer));
-		*(tmpbuffer+strlen(kdb_prompt_str) +
-		  (lastchar-buffer)) = '\0';
-		kdb_printf("\r%s\r", tmpbuffer);
-		*lastchar = (char)key;
-		*(lastchar+1) = '\0';
-		return lastchar;
 	case 9: /* Tab */
 		if (tab < 2)
 			++tab;
@@ -351,17 +358,27 @@
 			if (i >= dtab_count)
 				kdb_printf("...");
 			kdb_printf("\n");
-			kdb_printf(kdb_prompt_str);
+			kdb_printf("%s",  kdb_prompt_str);
 			kdb_printf("%s", buffer);
+			if (cp != lastchar)
+				kdb_position_cursor(kdb_prompt_str, buffer, cp);
 		} else if (tab != 2 && count > 0) {
-			len_tmp = strlen(p_tmp);
-			strncpy(p_tmp+len_tmp, cp, lastchar-cp+1);
-			len_tmp = strlen(p_tmp);
-			strncpy(cp, p_tmp+len, len_tmp-len + 1);
-			len = len_tmp - len;
-			kdb_printf("%s", cp);
-			cp += len;
-			lastchar += len;
+			/* How many new characters do we want from tmpbuffer? */
+			len_tmp = strlen(p_tmp) - len;
+			if (lastchar + len_tmp >= bufend)
+				len_tmp = bufend - lastchar;
+
+			if (len_tmp) {
+				/* + 1 ensures the '\0' is memmove'd */
+				memmove(cp+len_tmp, cp, (lastchar-cp) + 1);
+				memcpy(cp, p_tmp+len, len_tmp);
+				kdb_printf("%s", cp);
+				cp += len_tmp;
+				lastchar += len_tmp;
+				if (cp != lastchar)
+					kdb_position_cursor(kdb_prompt_str,
+							    buffer, cp);
+			}
 		}
 		kdb_nextline = 1; /* reset output line number */
 		break;
@@ -372,13 +389,9 @@
 				memcpy(cp+1, tmpbuffer, lastchar - cp);
 				*++lastchar = '\0';
 				*cp = key;
-				kdb_printf("%s\r", cp);
+				kdb_printf("%s", cp);
 				++cp;
-				tmp = *cp;
-				*cp = '\0';
-				kdb_printf(kdb_prompt_str);
-				kdb_printf("%s", buffer);
-				*cp = tmp;
+				kdb_position_cursor(kdb_prompt_str, buffer, cp);
 			} else {
 				*++lastchar = '\0';
 				*cp++ = key;
@@ -437,7 +450,7 @@
 {
 	if (prompt && kdb_prompt_str != prompt)
 		strscpy(kdb_prompt_str, prompt, CMD_BUFLEN);
-	kdb_printf(kdb_prompt_str);
+	kdb_printf("%s", kdb_prompt_str);
 	kdb_nextline = 1;	/* Prompt and input resets line number */
 	return kdb_read(buffer, bufsize);
 }
@@ -564,6 +577,8 @@
 			continue;
 		if (c == dbg_io_ops->cons)
 			continue;
+		if (!c->write)
+			continue;
 		/*
 		 * Set oops_in_progress to encourage the console drivers to
 		 * disregard their internal spin locks: in the current calling
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/debug/kdb/kdb_main.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/debug/kdb/kdb_main.c
@@ -1294,8 +1294,6 @@
 		/* PROMPT can only be set if we have MEM_READ permission. */
 		snprintf(kdb_prompt_str, CMD_BUFLEN, kdbgetenv("PROMPT"),
 			 raw_smp_processor_id());
-		if (defcmd_in_progress)
-			strncat(kdb_prompt_str, "[defcmd]", CMD_BUFLEN);
 
 		/*
 		 * Fetch command from keyboard
@@ -2203,8 +2201,8 @@
 			state = 'D';	/* cpu is online but unresponsive */
 		} else {
 			state = ' ';	/* cpu is responding to kdb */
-			if (kdb_task_state_char(KDB_TSK(i)) == 'I')
-				state = 'I';	/* idle task */
+			if (kdb_task_state_char(KDB_TSK(i)) == '-')
+				state = '-';	/* idle task */
 		}
 		if (state != prev_state) {
 			if (prev_state != '?') {
@@ -2271,37 +2269,30 @@
 void kdb_ps_suppressed(void)
 {
 	int idle = 0, daemon = 0;
-	unsigned long mask_I = kdb_task_state_string("I"),
-		      mask_M = kdb_task_state_string("M");
 	unsigned long cpu;
 	const struct task_struct *p, *g;
 	for_each_online_cpu(cpu) {
 		p = kdb_curr_task(cpu);
-		if (kdb_task_state(p, mask_I))
+		if (kdb_task_state(p, "-"))
 			++idle;
 	}
 	for_each_process_thread(g, p) {
-		if (kdb_task_state(p, mask_M))
+		if (kdb_task_state(p, "ims"))
 			++daemon;
 	}
 	if (idle || daemon) {
 		if (idle)
-			kdb_printf("%d idle process%s (state I)%s\n",
+			kdb_printf("%d idle process%s (state -)%s\n",
 				   idle, idle == 1 ? "" : "es",
 				   daemon ? " and " : "");
 		if (daemon)
-			kdb_printf("%d sleeping system daemon (state M) "
+			kdb_printf("%d sleeping system daemon (state [ims]) "
 				   "process%s", daemon,
 				   daemon == 1 ? "" : "es");
 		kdb_printf(" suppressed,\nuse 'ps A' to see all.\n");
 	}
 }
 
-/*
- * kdb_ps - This function implements the 'ps' command which shows a
- *	list of the active processes.
- *		ps [DRSTCZEUIMA]   All processes, optionally filtered by state
- */
 void kdb_ps1(const struct task_struct *p)
 {
 	int cpu;
@@ -2330,17 +2321,25 @@
 	}
 }
 
+/*
+ * kdb_ps - This function implements the 'ps' command which shows a
+ *	    list of the active processes.
+ *
+ * ps [<state_chars>]   Show processes, optionally selecting only those whose
+ *                      state character is found in <state_chars>.
+ */
 static int kdb_ps(int argc, const char **argv)
 {
 	struct task_struct *g, *p;
-	unsigned long mask, cpu;
+	const char *mask;
+	unsigned long cpu;
 
 	if (argc == 0)
 		kdb_ps_suppressed();
 	kdb_printf("%-*s      Pid   Parent [*] cpu State %-*s Command\n",
 		(int)(2*sizeof(void *))+2, "Task Addr",
 		(int)(2*sizeof(void *))+2, "Thread");
-	mask = kdb_task_state_string(argc ? argv[1] : NULL);
+	mask = argc ? argv[1] : kdbgetenv("PS");
 	/* Run the active tasks first */
 	for_each_online_cpu(cpu) {
 		if (KDB_FLAG(CMD_INTERRUPT))
@@ -2742,8 +2741,8 @@
 	},
 	{	.name = "bta",
 		.func = kdb_bt,
-		.usage = "[D|R|S|T|C|Z|E|U|I|M|A]",
-		.help = "Backtrace all processes matching state flag",
+		.usage = "[<state_chars>|A]",
+		.help = "Backtrace all processes whose state matches",
 		.flags = KDB_ENABLE_INSPECT,
 	},
 	{	.name = "btc",
@@ -2797,7 +2796,7 @@
 	},
 	{	.name = "ps",
 		.func = kdb_ps,
-		.usage = "[<flags>|A]",
+		.usage = "[<state_chars>|A]",
 		.help = "Display active task list",
 		.flags = KDB_ENABLE_INSPECT,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/debug/kdb/kdb_private.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/debug/kdb/kdb_private.h
@@ -190,10 +190,8 @@
 extern int kdb_grep_leading;
 extern int kdb_grep_trailing;
 extern char *kdb_cmds[];
-extern unsigned long kdb_task_state_string(const char *);
 extern char kdb_task_state_char (const struct task_struct *);
-extern unsigned long kdb_task_state(const struct task_struct *p,
-				    unsigned long mask);
+extern bool kdb_task_state(const struct task_struct *p, const char *mask);
 extern void kdb_ps_suppressed(void);
 extern void kdb_ps1(const struct task_struct *p);
 extern void kdb_send_sig(struct task_struct *p, int sig);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/debug/kdb/kdb_support.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/debug/kdb/kdb_support.c
@@ -24,6 +24,7 @@
 #include <linux/uaccess.h>
 #include <linux/kdb.h>
 #include <linux/slab.h>
+#include <linux/ctype.h>
 #include "kdb_private.h"
 
 /*
@@ -290,7 +291,7 @@
  */
 int kdb_putarea_size(unsigned long addr, void *res, size_t size)
 {
-	int ret = copy_from_kernel_nofault((char *)addr, (char *)res, size);
+	int ret = copy_to_kernel_nofault((char *)addr, (char *)res, size);
 	if (ret) {
 		if (!KDB_STATE(SUPPRESS)) {
 			kdb_func_printf("Bad address 0x%lx\n", addr);
@@ -473,82 +474,7 @@
 	return diag;
 }
 
-/*
- * kdb_task_state_string - Convert a string containing any of the
- *	letters DRSTCZEUIMA to a mask for the process state field and
- *	return the value.  If no argument is supplied, return the mask
- *	that corresponds to environment variable PS, DRSTCZEU by
- *	default.
- * Inputs:
- *	s	String to convert
- * Returns:
- *	Mask for process state.
- * Notes:
- *	The mask folds data from several sources into a single long value, so
- *	be careful not to overlap the bits.  TASK_* bits are in the LSB,
- *	special cases like UNRUNNABLE are in the MSB.  As of 2.6.10-rc1 there
- *	is no overlap between TASK_* and EXIT_* but that may not always be
- *	true, so EXIT_* bits are shifted left 16 bits before being stored in
- *	the mask.
- */
-
-/* unrunnable is < 0 */
-#define UNRUNNABLE	(1UL << (8*sizeof(unsigned long) - 1))
-#define RUNNING		(1UL << (8*sizeof(unsigned long) - 2))
-#define IDLE		(1UL << (8*sizeof(unsigned long) - 3))
-#define DAEMON		(1UL << (8*sizeof(unsigned long) - 4))
-
-unsigned long kdb_task_state_string(const char *s)
-{
-	long res = 0;
-	if (!s) {
-		s = kdbgetenv("PS");
-		if (!s)
-			s = "DRSTCZEU";	/* default value for ps */
-	}
-	while (*s) {
-		switch (*s) {
-		case 'D':
-			res |= TASK_UNINTERRUPTIBLE;
-			break;
-		case 'R':
-			res |= RUNNING;
-			break;
-		case 'S':
-			res |= TASK_INTERRUPTIBLE;
-			break;
-		case 'T':
-			res |= TASK_STOPPED;
-			break;
-		case 'C':
-			res |= TASK_TRACED;
-			break;
-		case 'Z':
-			res |= EXIT_ZOMBIE << 16;
-			break;
-		case 'E':
-			res |= EXIT_DEAD << 16;
-			break;
-		case 'U':
-			res |= UNRUNNABLE;
-			break;
-		case 'I':
-			res |= IDLE;
-			break;
-		case 'M':
-			res |= DAEMON;
-			break;
-		case 'A':
-			res = ~0UL;
-			break;
-		default:
-			  kdb_func_printf("unknown flag '%c' ignored\n", *s);
-			  break;
-		}
-		++s;
-	}
-	return res;
-}
+
 
 /*
  * kdb_task_state_char - Return the character that represents the task state.
@@ -559,7 +485,6 @@
  */
 char kdb_task_state_char (const struct task_struct *p)
 {
-	unsigned int p_state;
 	unsigned long tmp;
 	char state;
 	int cpu;
@@ -568,25 +493,18 @@
 	    copy_from_kernel_nofault(&tmp, (char *)p, sizeof(unsigned long)))
 		return 'E';
 
-	cpu = kdb_process_cpu(p);
-	p_state = READ_ONCE(p->__state);
-	state = (p_state == 0) ? 'R' :
-		(p_state < 0) ? 'U' :
-		(p_state & TASK_UNINTERRUPTIBLE) ? 'D' :
-		(p_state & TASK_STOPPED) ? 'T' :
-		(p_state & TASK_TRACED) ? 'C' :
-		(p->exit_state & EXIT_ZOMBIE) ? 'Z' :
-		(p->exit_state & EXIT_DEAD) ? 'E' :
-		(p_state & TASK_INTERRUPTIBLE) ? 'S' : '?';
+	state = task_state_to_char((struct task_struct *) p);
+
 	if (is_idle_task(p)) {
 		/* Idle task.  Is it really idle, apart from the kdb
 		 * interrupt? */
+		cpu = kdb_process_cpu(p);
 		if (!kdb_task_has_cpu(p) || kgdb_info[cpu].irq_depth == 1) {
 			if (cpu != kdb_initial_cpu)
-				state = 'I';	/* idle task */
+				state = '-';	/* idle task */
 		}
-	} else if (!p->mm && state == 'S') {
-		state = 'M';	/* sleeping system daemon */
+	} else if (!p->mm && strchr("IMS", state)) {
+		state = tolower(state);		/* sleeping system daemon */
 	}
 	return state;
 }
@@ -596,14 +514,28 @@
  *	given by the mask.
  * Inputs:
  *	p	struct task for the process
- *	mask	mask from kdb_task_state_string to select processes
+ *	mask	set of characters used to select processes; both NULL
+ *	        and the empty string mean adopt a default filter, which
+ *	        is to suppress sleeping system daemons and the idle tasks
  * Returns:
  *	True if the process matches at least one criteria defined by the mask.
  */
-unsigned long kdb_task_state(const struct task_struct *p, unsigned long mask)
+bool kdb_task_state(const struct task_struct *p, const char *mask)
 {
-	char state[] = { kdb_task_state_char(p), '\0' };
-	return (mask & kdb_task_state_string(state)) != 0;
+	char state = kdb_task_state_char(p);
+
+	/* If there is no mask, then we will filter code that runs when the
+	 * scheduler is idling and any system daemons that are currently
+	 * sleeping.
+	 */
+	if (!mask || mask[0] == '\0')
+		return !strchr("-ims", state);
+
+	/* A is a special case that matches all states */
+	if (strchr(mask, 'A'))
+		return true;
+
+	return strchr(mask, state);
 }
 
 /* Maintain a small stack of kdb_flags to allow recursion without disturbing
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/coherent.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/coherent.c
@@ -75,7 +75,7 @@
 	return ERR_PTR(-ENOMEM);
 }
 
-static void dma_release_coherent_memory(struct dma_coherent_mem *mem)
+static void _dma_release_coherent_memory(struct dma_coherent_mem *mem)
 {
 	if (!mem)
 		return;
@@ -127,10 +127,18 @@
 
 	ret = dma_assign_coherent_memory(dev, mem);
 	if (ret)
-		dma_release_coherent_memory(mem);
+		_dma_release_coherent_memory(mem);
 	return ret;
 }
 
+void dma_release_coherent_memory(struct device *dev)
+{
+	if (dev) {
+		_dma_release_coherent_memory(dev->dma_mem);
+		dev->dma_mem = NULL;
+	}
+}
+
 static void *__dma_alloc_from_coherent(struct device *dev,
 				       struct dma_coherent_mem *mem,
 				       ssize_t size, dma_addr_t *dma_handle)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/contiguous.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/contiguous.c
@@ -399,8 +399,6 @@
 
 static int __init rmem_cma_setup(struct reserved_mem *rmem)
 {
-	phys_addr_t align = PAGE_SIZE << max(MAX_ORDER - 1, pageblock_order);
-	phys_addr_t mask = align - 1;
 	unsigned long node = rmem->fdt_node;
 	bool default_cma = of_get_flat_dt_prop(node, "linux,cma-default", NULL);
 	struct cma *cma;
@@ -416,7 +414,7 @@
 	    of_get_flat_dt_prop(node, "no-map", NULL))
 		return -EINVAL;
 
-	if ((rmem->base & mask) || (rmem->size & mask)) {
+	if (!IS_ALIGNED(rmem->base | rmem->size, CMA_MIN_ALIGNMENT_BYTES)) {
 		pr_err("Reserved memory: incorrect alignment of CMA region\n");
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/debug.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/debug.c
@@ -447,8 +447,11 @@
  * dma_active_cacheline entry to track per event.  dma_map_sg(), on the
  * other hand, consumes a single dma_debug_entry, but inserts 'nents'
  * entries into the tree.
+ *
+ * Use __GFP_NOWARN because the printk from an OOM, to netconsole, could end
+ * up right back in the DMA debugging code, leading to a deadlock.
  */
-static RADIX_TREE(dma_active_cacheline, GFP_NOWAIT);
+static RADIX_TREE(dma_active_cacheline, GFP_ATOMIC | __GFP_NOWARN);
 static DEFINE_SPINLOCK(radix_lock);
 #define ACTIVE_CACHELINE_MAX_OVERLAP ((1 << RADIX_TREE_MAX_TAGS) - 1)
 #define CACHELINE_PER_PAGE_SHIFT (PAGE_SHIFT - L1_CACHE_SHIFT)
@@ -564,7 +567,7 @@
 
 	rc = active_cacheline_insert(entry);
 	if (rc == -ENOMEM) {
-		pr_err("cacheline tracking ENOMEM, dma-debug disabled\n");
+		pr_err_once("cacheline tracking ENOMEM, dma-debug disabled\n");
 		global_disable = true;
 	} else if (rc == -EEXIST && !(attrs & DMA_ATTR_SKIP_CPU_SYNC)) {
 		err_printk(entry->dev, entry,
@@ -605,15 +608,19 @@
 	return entry;
 }
 
-static void __dma_entry_alloc_check_leak(void)
+/*
+ * This should be called outside of free_entries_lock scope to avoid potential
+ * deadlocks with serial consoles that use DMA.
+ */
+static void __dma_entry_alloc_check_leak(u32 nr_entries)
 {
-	u32 tmp = nr_total_entries % nr_prealloc_entries;
+	u32 tmp = nr_entries % nr_prealloc_entries;
 
 	/* Shout each time we tick over some multiple of the initial pool */
 	if (tmp < DMA_DEBUG_DYNAMIC_ENTRIES) {
 		pr_info("dma_debug_entry pool grown to %u (%u00%%)\n",
-			nr_total_entries,
-			(nr_total_entries / nr_prealloc_entries));
+			nr_entries,
+			(nr_entries / nr_prealloc_entries));
 	}
 }
 
@@ -624,8 +631,10 @@
  */
 static struct dma_debug_entry *dma_entry_alloc(void)
 {
+	bool alloc_check_leak = false;
 	struct dma_debug_entry *entry;
 	unsigned long flags;
+	u32 nr_entries;
 
 	spin_lock_irqsave(&free_entries_lock, flags);
 	if (num_free_entries == 0) {
@@ -635,13 +644,17 @@
 			pr_err("debugging out of memory - disabling\n");
 			return NULL;
 		}
-		__dma_entry_alloc_check_leak();
+		alloc_check_leak = true;
+		nr_entries = nr_total_entries;
 	}
 
 	entry = __dma_entry_alloc();
 
 	spin_unlock_irqrestore(&free_entries_lock, flags);
 
+	if (alloc_check_leak)
+		__dma_entry_alloc_check_leak(nr_entries);
+
 #ifdef CONFIG_STACKTRACE
 	entry->stack_len = stack_trace_save(entry->stack_entries,
 					    ARRAY_SIZE(entry->stack_entries),
@@ -927,7 +940,7 @@
 		global_disable = true;
 	}
 
-	return 0;
+	return 1;
 }
 
 static __init int dma_debug_entries_cmdline(char *str)
@@ -936,7 +949,7 @@
 		return -EINVAL;
 	if (!get_option(&str, &nr_prealloc_entries))
 		nr_prealloc_entries = PREALLOC_DMA_DEBUG_ENTRIES;
-	return 0;
+	return 1;
 }
 
 __setup("dma_debug=", dma_debug_cmdline);
@@ -1033,9 +1046,13 @@
 	}
 
 	hash_bucket_del(entry);
-	dma_entry_free(entry);
-
 	put_hash_bucket(bucket, flags);
+
+	/*
+	 * Free the entry outside of bucket_lock to avoid ABBA deadlocks
+	 * between that and radix_lock.
+	 */
+	dma_entry_free(entry);
 }
 
 static void check_for_stack(struct device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/direct.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/direct.c
@@ -75,6 +75,25 @@
 		min_not_zero(dev->coherent_dma_mask, dev->bus_dma_limit);
 }
 
+static int dma_set_decrypted(struct device *dev, void *vaddr, size_t size)
+{
+	if (!force_dma_unencrypted(dev))
+		return 0;
+	return set_memory_decrypted((unsigned long)vaddr, PFN_UP(size));
+}
+
+static int dma_set_encrypted(struct device *dev, void *vaddr, size_t size)
+{
+	int ret;
+
+	if (!force_dma_unencrypted(dev))
+		return 0;
+	ret = set_memory_encrypted((unsigned long)vaddr, PFN_UP(size));
+	if (ret)
+		pr_warn_ratelimited("leaking DMA memory that can't be re-encrypted\n");
+	return ret;
+}
+
 static void __dma_direct_free_pages(struct device *dev, struct page *page,
 				    size_t size)
 {
@@ -85,7 +104,7 @@
 }
 
 static struct page *__dma_direct_alloc_pages(struct device *dev, size_t size,
-		gfp_t gfp)
+		gfp_t gfp, bool allow_highmem)
 {
 	int node = dev_to_node(dev);
 	struct page *page = NULL;
@@ -106,9 +125,12 @@
 	}
 
 	page = dma_alloc_contiguous(dev, size, gfp);
-	if (page && !dma_coherent_ok(dev, page_to_phys(page), size)) {
-		dma_free_contiguous(dev, page, size);
-		page = NULL;
+	if (page) {
+		if (!dma_coherent_ok(dev, page_to_phys(page), size) ||
+		    (!allow_highmem && PageHighMem(page))) {
+			dma_free_contiguous(dev, page, size);
+			page = NULL;
+		}
 	}
 again:
 	if (!page)
@@ -149,29 +171,37 @@
 	return ret;
 }
 
+static void *dma_direct_alloc_no_mapping(struct device *dev, size_t size,
+		dma_addr_t *dma_handle, gfp_t gfp)
+{
+	struct page *page;
+
+	page = __dma_direct_alloc_pages(dev, size, gfp & ~__GFP_ZERO, true);
+	if (!page)
+		return NULL;
+
+	/* remove any dirty cache lines on the kernel alias */
+	if (!PageHighMem(page))
+		arch_dma_prep_coherent(page, size);
+
+	/* return the page pointer as the opaque cookie */
+	*dma_handle = phys_to_dma_direct(dev, page_to_phys(page));
+	return page;
+}
+
 void *dma_direct_alloc(struct device *dev, size_t size,
 		dma_addr_t *dma_handle, gfp_t gfp, unsigned long attrs)
 {
 	struct page *page;
 	void *ret;
-	int err;
 
 	size = PAGE_ALIGN(size);
 	if (attrs & DMA_ATTR_NO_WARN)
 		gfp |= __GFP_NOWARN;
 
 	if ((attrs & DMA_ATTR_NO_KERNEL_MAPPING) &&
-	    !force_dma_unencrypted(dev) && !is_swiotlb_for_alloc(dev)) {
-		page = __dma_direct_alloc_pages(dev, size, gfp & ~__GFP_ZERO);
-		if (!page)
-			return NULL;
-		/* remove any dirty cache lines on the kernel alias */
-		if (!PageHighMem(page))
-			arch_dma_prep_coherent(page, size);
-		*dma_handle = phys_to_dma_direct(dev, page_to_phys(page));
-		/* return the page pointer as the opaque cookie */
-		return page;
-	}
+	    !force_dma_unencrypted(dev) && !is_swiotlb_for_alloc(dev))
+		return dma_direct_alloc_no_mapping(dev, size, dma_handle, gfp);
 
 	if (!IS_ENABLED(CONFIG_ARCH_HAS_DMA_SET_UNCACHED) &&
 	    !IS_ENABLED(CONFIG_DMA_DIRECT_REMAP) &&
@@ -200,7 +230,7 @@
 		return dma_direct_alloc_from_pool(dev, size, dma_handle, gfp);
 
 	/* we always manually zero the memory once we are done */
-	page = __dma_direct_alloc_pages(dev, size, gfp & ~__GFP_ZERO);
+	page = __dma_direct_alloc_pages(dev, size, gfp & ~__GFP_ZERO, true);
 	if (!page)
 		return NULL;
 
@@ -216,12 +246,6 @@
 				__builtin_return_address(0));
 		if (!ret)
 			goto out_free_pages;
-		if (force_dma_unencrypted(dev)) {
-			err = set_memory_decrypted((unsigned long)ret,
-						   1 << get_order(size));
-			if (err)
-				goto out_free_pages;
-		}
 		memset(ret, 0, size);
 		goto done;
 	}
@@ -238,13 +262,8 @@
 	}
 
 	ret = page_address(page);
-	if (force_dma_unencrypted(dev)) {
-		err = set_memory_decrypted((unsigned long)ret,
-					   1 << get_order(size));
-		if (err)
-			goto out_free_pages;
-	}
-
+	if (dma_set_decrypted(dev, ret, size))
+		goto out_free_pages;
 	memset(ret, 0, size);
 
 	if (IS_ENABLED(CONFIG_ARCH_HAS_DMA_SET_UNCACHED) &&
@@ -259,13 +278,8 @@
 	return ret;
 
 out_encrypt_pages:
-	if (force_dma_unencrypted(dev)) {
-		err = set_memory_encrypted((unsigned long)page_address(page),
-					   1 << get_order(size));
-		/* If memory cannot be re-encrypted, it must be leaked */
-		if (err)
-			return NULL;
-	}
+	if (dma_set_encrypted(dev, page_address(page), size))
+		return NULL;
 out_free_pages:
 	__dma_direct_free_pages(dev, page, size);
 	return NULL;
@@ -304,13 +318,14 @@
 	    dma_free_from_pool(dev, cpu_addr, PAGE_ALIGN(size)))
 		return;
 
-	if (force_dma_unencrypted(dev))
-		set_memory_encrypted((unsigned long)cpu_addr, 1 << page_order);
-
-	if (IS_ENABLED(CONFIG_DMA_REMAP) && is_vmalloc_addr(cpu_addr))
+	if (IS_ENABLED(CONFIG_DMA_REMAP) && is_vmalloc_addr(cpu_addr)) {
 		vunmap(cpu_addr);
-	else if (IS_ENABLED(CONFIG_ARCH_HAS_DMA_CLEAR_UNCACHED))
-		arch_dma_clear_uncached(cpu_addr, size);
+	} else {
+		if (IS_ENABLED(CONFIG_ARCH_HAS_DMA_CLEAR_UNCACHED))
+			arch_dma_clear_uncached(cpu_addr, size);
+		if (dma_set_encrypted(dev, cpu_addr, size))
+			return;
+	}
 
 	__dma_direct_free_pages(dev, dma_direct_to_page(dev, dma_addr), size);
 }
@@ -326,26 +341,13 @@
 	    !is_swiotlb_for_alloc(dev))
 		return dma_direct_alloc_from_pool(dev, size, dma_handle, gfp);
 
-	page = __dma_direct_alloc_pages(dev, size, gfp);
+	page = __dma_direct_alloc_pages(dev, size, gfp, false);
 	if (!page)
 		return NULL;
-	if (PageHighMem(page)) {
-		/*
-		 * Depending on the cma= arguments and per-arch setup
-		 * dma_alloc_contiguous could return highmem pages.
-		 * Without remapping there is no way to return them here,
-		 * so log an error and fail.
-		 */
-		dev_info(dev, "Rejecting highmem page from CMA.\n");
-		goto out_free_pages;
-	}
 
 	ret = page_address(page);
-	if (force_dma_unencrypted(dev)) {
-		if (set_memory_decrypted((unsigned long)ret,
-				1 << get_order(size)))
-			goto out_free_pages;
-	}
+	if (dma_set_decrypted(dev, ret, size))
+		goto out_free_pages;
 	memset(ret, 0, size);
 	*dma_handle = phys_to_dma_direct(dev, page_to_phys(page));
 	return page;
@@ -358,7 +360,6 @@
 		struct page *page, dma_addr_t dma_addr,
 		enum dma_data_direction dir)
 {
-	unsigned int page_order = get_order(size);
 	void *vaddr = page_address(page);
 
 	/* If cpu_addr is not from an atomic pool, dma_free_from_pool() fails */
@@ -366,9 +367,8 @@
 	    dma_free_from_pool(dev, vaddr, size))
 		return;
 
-	if (force_dma_unencrypted(dev))
-		set_memory_encrypted((unsigned long)vaddr, 1 << page_order);
-
+	if (dma_set_encrypted(dev, vaddr, size))
+		return;
 	__dma_direct_free_pages(dev, page, size);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/direct.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/direct.h
@@ -114,6 +114,7 @@
 		dma_direct_sync_single_for_cpu(dev, addr, size, dir);
 
 	if (unlikely(is_swiotlb_buffer(dev, phys)))
-		swiotlb_tbl_unmap_single(dev, phys, size, dir, attrs);
+		swiotlb_tbl_unmap_single(dev, phys, size, dir,
+					 attrs | DMA_ATTR_SKIP_CPU_SYNC);
 }
 #endif /* _KERNEL_DMA_DIRECT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/map_benchmark.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/map_benchmark.c
@@ -112,6 +112,22 @@
 		atomic64_add(map_sq, &map->sum_sq_map);
 		atomic64_add(unmap_sq, &map->sum_sq_unmap);
 		atomic64_inc(&map->loops);
+
+		/*
+		 * We may test for a long time so periodically check whether
+		 * we need to schedule to avoid starving the others. Otherwise
+		 * we may hangup the kernel in a non-preemptible kernel when
+		 * the test kthreads number >= CPU number, the test kthreads
+		 * will run endless on every CPU since the thread resposible
+		 * for notifying the kthread stop (in do_map_benchmark())
+		 * could not be scheduled.
+		 *
+		 * Note this may degrade the test concurrency since the test
+		 * threads may need to share the CPU time with other load
+		 * in the system. So it's recommended to run this benchmark
+		 * on an idle system.
+		 */
+		cond_resched();
 	}
 
 out:
@@ -124,7 +140,6 @@
 	struct task_struct **tsk;
 	int threads = map->bparam.threads;
 	int node = map->bparam.node;
-	const cpumask_t *cpu_mask = cpumask_of_node(node);
 	u64 loops;
 	int ret = 0;
 	int i;
@@ -145,7 +160,7 @@
 		}
 
 		if (node != NUMA_NO_NODE)
-			kthread_bind_mask(tsk[i], cpu_mask);
+			kthread_bind_mask(tsk[i], cpumask_of_node(node));
 	}
 
 	/* clear the old value in the previous benchmark */
@@ -231,7 +246,8 @@
 		}
 
 		if (map->bparam.node != NUMA_NO_NODE &&
-		    !node_possible(map->bparam.node)) {
+		    (map->bparam.node < 0 || map->bparam.node >= MAX_NUMNODES ||
+		     !node_possible(map->bparam.node))) {
 			pr_err("invalid numa node\n");
 			return -EINVAL;
 		}
@@ -275,6 +291,9 @@
 		 * dma_mask changed by benchmark
 		 */
 		dma_set_mask(map->dev, old_dma_mask);
+
+		if (ret)
+			return ret;
 		break;
 	default:
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/mapping.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/mapping.c
@@ -62,8 +62,8 @@
 {
 	struct dma_devres match_data = { size, vaddr, dma_handle };
 
-	dma_free_coherent(dev, size, vaddr, dma_handle);
 	WARN_ON(devres_destroy(dev, dmam_release, dmam_match, &match_data));
+	dma_free_coherent(dev, size, vaddr, dma_handle);
 }
 EXPORT_SYMBOL(dmam_free_coherent);
 
@@ -296,10 +296,6 @@
 	if (WARN_ON_ONCE(!dev->dma_mask))
 		return DMA_MAPPING_ERROR;
 
-	/* Don't allow RAM to be mapped */
-	if (WARN_ON_ONCE(pfn_valid(PHYS_PFN(phys_addr))))
-		return DMA_MAPPING_ERROR;
-
 	if (dma_map_direct(dev, ops))
 		addr = dma_direct_map_resource(dev, phys_addr, size, dir, attrs);
 	else if (ops->map_resource)
@@ -781,6 +777,18 @@
 }
 EXPORT_SYMBOL_GPL(dma_max_mapping_size);
 
+size_t dma_opt_mapping_size(struct device *dev)
+{
+	const struct dma_map_ops *ops = get_dma_ops(dev);
+	size_t size = SIZE_MAX;
+
+	if (ops && ops->opt_mapping_size)
+		size = ops->opt_mapping_size();
+
+	return min(dma_max_mapping_size(dev), size);
+}
+EXPORT_SYMBOL_GPL(dma_opt_mapping_size);
+
 bool dma_need_sync(struct device *dev, dma_addr_t dma_addr)
 {
 	const struct dma_map_ops *ops = get_dma_ops(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/pool.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/pool.c
@@ -203,7 +203,7 @@
 						    GFP_KERNEL);
 	if (!atomic_pool_kernel)
 		ret = -ENOMEM;
-	if (IS_ENABLED(CONFIG_ZONE_DMA)) {
+	if (has_managed_dma()) {
 		atomic_pool_dma = __dma_atomic_pool_init(atomic_pool_size,
 						GFP_KERNEL | GFP_DMA);
 		if (!atomic_pool_dma)
@@ -226,7 +226,7 @@
 	if (prev == NULL) {
 		if (IS_ENABLED(CONFIG_ZONE_DMA32) && (gfp & GFP_DMA32))
 			return atomic_pool_dma32;
-		if (IS_ENABLED(CONFIG_ZONE_DMA) && (gfp & GFP_DMA))
+		if (atomic_pool_dma && (gfp & GFP_DMA))
 			return atomic_pool_dma;
 		return atomic_pool_kernel;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/remap.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/remap.c
@@ -43,13 +43,13 @@
 	void *vaddr;
 	int i;
 
-	pages = kmalloc_array(count, sizeof(struct page *), GFP_KERNEL);
+	pages = kvmalloc_array(count, sizeof(struct page *), GFP_KERNEL);
 	if (!pages)
 		return NULL;
 	for (i = 0; i < count; i++)
 		pages[i] = nth_page(page, i);
 	vaddr = vmap(pages, count, VM_DMA_COHERENT, prot);
-	kfree(pages);
+	kvfree(pages);
 
 	return vaddr;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/dma/swiotlb.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/dma/swiotlb.c
@@ -247,7 +247,7 @@
 	return;
 
 fail_free_mem:
-	memblock_free_early(__pa(tlb), bytes);
+	memblock_free(__pa(tlb), bytes);
 fail:
 	pr_warn("Cannot allocate buffer");
 }
@@ -435,7 +435,10 @@
 	}
 }
 
-#define slot_addr(start, idx)	((start) + ((idx) << IO_TLB_SHIFT))
+static inline phys_addr_t slot_addr(phys_addr_t start, phys_addr_t idx)
+{
+	return start + (idx << IO_TLB_SHIFT);
+}
 
 /*
  * Carefully handle integer overflow which can occur when boundary_mask == ~0UL.
@@ -459,15 +462,14 @@
  * allocate a buffer from that IO TLB pool.
  */
 static int swiotlb_find_slots(struct device *dev, phys_addr_t orig_addr,
-			      size_t alloc_size)
+			      size_t alloc_size, unsigned int alloc_align_mask)
 {
 	struct io_tlb_mem *mem = dev->dma_io_tlb_mem;
 	unsigned long boundary_mask = dma_get_seg_boundary(dev);
 	dma_addr_t tbl_dma_addr =
 		phys_to_dma_unencrypted(dev, mem->start) & boundary_mask;
 	unsigned long max_slots = get_max_slots(boundary_mask);
-	unsigned int iotlb_align_mask =
-		dma_get_min_align_mask(dev) & ~(IO_TLB_SIZE - 1);
+	unsigned int iotlb_align_mask = dma_get_min_align_mask(dev);
 	unsigned int nslots = nr_slots(alloc_size), stride;
 	unsigned int index, wrap, count = 0, i;
 	unsigned int offset = swiotlb_align_offset(dev, orig_addr);
@@ -476,6 +478,14 @@
 	BUG_ON(!nslots);
 
 	/*
+	 * Ensure that the allocation is at least slot-aligned and update
+	 * 'iotlb_align_mask' to ignore bits that will be preserved when
+	 * offsetting into the allocation.
+	 */
+	alloc_align_mask |= (IO_TLB_SIZE - 1);
+	iotlb_align_mask &= ~alloc_align_mask;
+
+	/*
 	 * For mappings with an alignment requirement don't bother looping to
 	 * unaligned slots once we found an aligned one.  For allocations of
 	 * PAGE_SIZE or larger only look for page aligned allocations.
@@ -483,6 +493,7 @@
 	stride = (iotlb_align_mask >> IO_TLB_SHIFT) + 1;
 	if (alloc_size >= PAGE_SIZE)
 		stride = max(stride, stride << (PAGE_SHIFT - IO_TLB_SHIFT));
+	stride = max(stride, (alloc_align_mask >> IO_TLB_SHIFT) + 1);
 
 	spin_lock_irqsave(&mem->lock, flags);
 	if (unlikely(nslots > mem->nslabs - mem->used))
@@ -541,7 +552,8 @@
 
 phys_addr_t swiotlb_tbl_map_single(struct device *dev, phys_addr_t orig_addr,
 		size_t mapping_size, size_t alloc_size,
-		enum dma_data_direction dir, unsigned long attrs)
+		unsigned int alloc_align_mask, enum dma_data_direction dir,
+		unsigned long attrs)
 {
 	struct io_tlb_mem *mem = dev->dma_io_tlb_mem;
 	unsigned int offset = swiotlb_align_offset(dev, orig_addr);
@@ -549,7 +561,7 @@
 	int index;
 	phys_addr_t tlb_addr;
 
-	if (!mem)
+	if (!mem || !mem->nslabs)
 		panic("Can not allocate SWIOTLB buffer earlier and can't now provide you with the DMA bounce buffer");
 
 	if (mem_encrypt_active())
@@ -561,7 +573,8 @@
 		return (phys_addr_t)DMA_MAPPING_ERROR;
 	}
 
-	index = swiotlb_find_slots(dev, orig_addr, alloc_size + offset);
+	index = swiotlb_find_slots(dev, orig_addr,
+				   alloc_size + offset, alloc_align_mask);
 	if (index == -1) {
 		if (!(attrs & DMA_ATTR_NO_WARN))
 			dev_warn_ratelimited(dev,
@@ -578,9 +591,14 @@
 	for (i = 0; i < nr_slots(alloc_size + offset); i++)
 		mem->slots[index + i].orig_addr = slot_addr(orig_addr, i);
 	tlb_addr = slot_addr(mem->start, index) + offset;
-	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC) &&
-	    (dir == DMA_TO_DEVICE || dir == DMA_BIDIRECTIONAL))
-		swiotlb_bounce(dev, tlb_addr, mapping_size, DMA_TO_DEVICE);
+	/*
+	 * When dir == DMA_FROM_DEVICE we could omit the copy from the orig
+	 * to the tlb buffer, if we knew for sure the device will
+	 * overwirte the entire current content. But we don't. Thus
+	 * unconditional bounce may prevent leaking swiotlb content (i.e.
+	 * kernel memory) to user-space.
+	 */
+	swiotlb_bounce(dev, tlb_addr, mapping_size, DMA_TO_DEVICE);
 	return tlb_addr;
 }
 
@@ -675,7 +693,7 @@
 	trace_swiotlb_bounced(dev, phys_to_dma(dev, paddr), size,
 			      swiotlb_force);
 
-	swiotlb_addr = swiotlb_tbl_map_single(dev, paddr, size, size, dir,
+	swiotlb_addr = swiotlb_tbl_map_single(dev, paddr, size, size, 0, dir,
 			attrs);
 	if (swiotlb_addr == (phys_addr_t)DMA_MAPPING_ERROR)
 		return DMA_MAPPING_ERROR;
@@ -698,7 +716,18 @@
 
 size_t swiotlb_max_mapping_size(struct device *dev)
 {
-	return ((size_t)IO_TLB_SIZE) * IO_TLB_SEGSIZE;
+	int min_align_mask = dma_get_min_align_mask(dev);
+	int min_align = 0;
+
+	/*
+	 * swiotlb_find_slots() skips slots according to
+	 * min align mask. This affects max mapping size.
+	 * Take it into acount here.
+	 */
+	if (min_align_mask)
+		min_align = roundup(min_align_mask, IO_TLB_SIZE);
+
+	return ((size_t)IO_TLB_SIZE) * IO_TLB_SEGSIZE - min_align;
 }
 
 bool is_swiotlb_active(struct device *dev)
@@ -759,7 +788,7 @@
 	if (!mem)
 		return NULL;
 
-	index = swiotlb_find_slots(dev, 0, size);
+	index = swiotlb_find_slots(dev, 0, size, 0);
 	if (index == -1)
 		return NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/entry/common.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/entry/common.c
@@ -73,8 +73,14 @@
 	/* Either of the above might have changed the syscall number */
 	syscall = syscall_get_nr(current, regs);
 
-	if (unlikely(work & SYSCALL_WORK_SYSCALL_TRACEPOINT))
+	if (unlikely(work & SYSCALL_WORK_SYSCALL_TRACEPOINT)) {
 		trace_sys_enter(regs, syscall);
+		/*
+		 * Probes or BPF hooks in the tracepoint may have changed the
+		 * system call number as well.
+		 */
+		syscall = syscall_get_nr(current, regs);
+	}
 
 	syscall_enter_audit(regs, syscall);
 
@@ -124,7 +130,7 @@
 {
 	instrumentation_begin();
 	trace_hardirqs_on_prepare();
-	lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+	lockdep_hardirqs_on_prepare();
 	instrumentation_end();
 
 	user_enter_irqoff();
@@ -187,7 +193,7 @@
 		/* Check if any of the above work has queued a deferred wakeup */
 		tick_nohz_user_enter_prepare();
 
-		ti_work = READ_ONCE(current_thread_info()->flags);
+		ti_work = read_thread_flags();
 	}
 
 	/* Return the latest work state for arch_exit_to_user_mode() */
@@ -196,13 +202,14 @@
 
 static void exit_to_user_mode_prepare(struct pt_regs *regs)
 {
-	unsigned long ti_work = READ_ONCE(current_thread_info()->flags);
+	unsigned long ti_work;
 
 	lockdep_assert_irqs_disabled();
 
 	/* Flush pending rcuog wakeup before the last need_resched() check */
 	tick_nohz_user_enter_prepare();
 
+	ti_work = read_thread_flags();
 	if (unlikely(ti_work & EXIT_TO_USER_MODE_WORK))
 		ti_work = exit_to_user_mode_loop(regs, ti_work);
 
@@ -412,7 +419,7 @@
 			instrumentation_begin();
 			/* Tell the tracer that IRET will enable interrupts */
 			trace_hardirqs_on_prepare();
-			lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+			lockdep_hardirqs_on_prepare();
 			instrumentation_end();
 			rcu_irq_exit();
 			lockdep_hardirqs_on(CALLER_ADDR0);
@@ -465,7 +472,7 @@
 	ftrace_nmi_exit();
 	if (irq_state.lockdep) {
 		trace_hardirqs_on_prepare();
-		lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+		lockdep_hardirqs_on_prepare();
 	}
 	instrumentation_end();
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/entry/kvm.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/entry/kvm.c
@@ -26,7 +26,7 @@
 		if (ret)
 			return ret;
 
-		ti_work = READ_ONCE(current_thread_info()->flags);
+		ti_work = read_thread_flags();
 	} while (ti_work & XFER_TO_GUEST_MODE_WORK || need_resched());
 	return 0;
 }
@@ -43,7 +43,7 @@
 	 * disabled in the inner loop before going into guest mode. No need
 	 * to disable interrupts here.
 	 */
-	ti_work = READ_ONCE(current_thread_info()->flags);
+	ti_work = read_thread_flags();
 	if (!(ti_work & XFER_TO_GUEST_MODE_WORK))
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/entry/syscall_user_dispatch.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/entry/syscall_user_dispatch.c
@@ -47,14 +47,18 @@
 		 * access_ok() is performed once, at prctl time, when
 		 * the selector is loaded by userspace.
 		 */
-		if (unlikely(__get_user(state, sd->selector)))
-			do_exit(SIGSEGV);
+		if (unlikely(__get_user(state, sd->selector))) {
+			force_exit_sig(SIGSEGV);
+			return true;
+		}
 
 		if (likely(state == SYSCALL_DISPATCH_FILTER_ALLOW))
 			return false;
 
-		if (state != SYSCALL_DISPATCH_FILTER_BLOCK)
-			do_exit(SIGSYS);
+		if (state != SYSCALL_DISPATCH_FILTER_BLOCK) {
+			force_exit_sig(SIGSYS);
+			return true;
+		}
 	}
 
 	sd->on_dispatch = true;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/events/core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/events/core.c
@@ -54,6 +54,7 @@
 #include <linux/highmem.h>
 #include <linux/pgtable.h>
 #include <linux/buildid.h>
+#include <linux/task_work.h>
 
 #include "internal.h"
 
@@ -414,8 +415,13 @@
  *   0 - disallow raw tracepoint access for unpriv
  *   1 - disallow cpu events for unpriv
  *   2 - disallow kernel profiling for unpriv
+ *   4 - disallow all unpriv perf event use
  */
+#ifdef CONFIG_SECURITY_PERF_EVENTS_RESTRICT
+int sysctl_perf_event_paranoid __read_mostly = PERF_SECURITY_MAX;
+#else
 int sysctl_perf_event_paranoid __read_mostly = 2;
+#endif
 
 /* Minimum for 512 kiB + 1 user control page */
 int sysctl_perf_event_mlock __read_mostly = 512 + (PAGE_SIZE / 1024); /* 'free' kiB per user */
@@ -674,6 +680,23 @@
 	WRITE_ONCE(event->state, state);
 }
 
+/*
+ * UP store-release, load-acquire
+ */
+
+#define __store_release(ptr, val)					\
+do {									\
+	barrier();							\
+	WRITE_ONCE(*(ptr), (val));					\
+} while (0)
+
+#define __load_acquire(ptr)						\
+({									\
+	__unqual_scalar_typeof(*(ptr)) ___p = READ_ONCE(*(ptr));	\
+	barrier();							\
+	___p;								\
+})
+
 #ifdef CONFIG_CGROUP_PERF
 
 static inline bool
@@ -719,34 +742,51 @@
 	return t->time;
 }
 
-static inline void __update_cgrp_time(struct perf_cgroup *cgrp)
+static inline u64 perf_cgroup_event_time_now(struct perf_event *event, u64 now)
 {
-	struct perf_cgroup_info *info;
-	u64 now;
-
-	now = perf_clock();
+	struct perf_cgroup_info *t;
 
-	info = this_cpu_ptr(cgrp->info);
+	t = per_cpu_ptr(event->cgrp->info, event->cpu);
+	if (!__load_acquire(&t->active))
+		return t->time;
+	now += READ_ONCE(t->timeoffset);
+	return now;
+}
 
-	info->time += now - info->timestamp;
+static inline void __update_cgrp_time(struct perf_cgroup_info *info, u64 now, bool adv)
+{
+	if (adv)
+		info->time += now - info->timestamp;
 	info->timestamp = now;
+	/*
+	 * see update_context_time()
+	 */
+	WRITE_ONCE(info->timeoffset, info->time - info->timestamp);
 }
 
-static inline void update_cgrp_time_from_cpuctx(struct perf_cpu_context *cpuctx)
+static inline void update_cgrp_time_from_cpuctx(struct perf_cpu_context *cpuctx, bool final)
 {
 	struct perf_cgroup *cgrp = cpuctx->cgrp;
 	struct cgroup_subsys_state *css;
+	struct perf_cgroup_info *info;
 
 	if (cgrp) {
+		u64 now = perf_clock();
+
 		for (css = &cgrp->css; css; css = css->parent) {
 			cgrp = container_of(css, struct perf_cgroup, css);
-			__update_cgrp_time(cgrp);
+			info = this_cpu_ptr(cgrp->info);
+
+			__update_cgrp_time(info, now, true);
+			if (final)
+				__store_release(&info->active, 0);
 		}
 	}
 }
 
 static inline void update_cgrp_time_from_event(struct perf_event *event)
 {
+	struct perf_cgroup_info *info;
 	struct perf_cgroup *cgrp;
 
 	/*
@@ -760,8 +800,10 @@
 	/*
 	 * Do not update time when cgroup is not active
 	 */
-	if (cgroup_is_descendant(cgrp->css.cgroup, event->cgrp->css.cgroup))
-		__update_cgrp_time(event->cgrp);
+	if (cgroup_is_descendant(cgrp->css.cgroup, event->cgrp->css.cgroup)) {
+		info = this_cpu_ptr(event->cgrp->info);
+		__update_cgrp_time(info, perf_clock(), true);
+	}
 }
 
 static inline void
@@ -785,7 +827,8 @@
 	for (css = &cgrp->css; css; css = css->parent) {
 		cgrp = container_of(css, struct perf_cgroup, css);
 		info = this_cpu_ptr(cgrp->info);
-		info->timestamp = ctx->timestamp;
+		__update_cgrp_time(info, ctx->timestamp, false);
+		__store_release(&info->active, 1);
 	}
 }
 
@@ -802,7 +845,7 @@
  */
 static void perf_cgroup_switch(struct task_struct *task, int mode)
 {
-	struct perf_cpu_context *cpuctx;
+	struct perf_cpu_context *cpuctx, *tmp;
 	struct list_head *list;
 	unsigned long flags;
 
@@ -813,7 +856,7 @@
 	local_irq_save(flags);
 
 	list = this_cpu_ptr(&cgrp_cpuctx_list);
-	list_for_each_entry(cpuctx, list, cgrp_cpuctx_entry) {
+	list_for_each_entry_safe(cpuctx, tmp, list, cgrp_cpuctx_entry) {
 		WARN_ON_ONCE(cpuctx->ctx.nr_cgroups == 0);
 
 		perf_ctx_lock(cpuctx, cpuctx->task_ctx);
@@ -982,14 +1025,6 @@
 }
 
 static inline void
-perf_cgroup_set_shadow_time(struct perf_event *event, u64 now)
-{
-	struct perf_cgroup_info *t;
-	t = per_cpu_ptr(event->cgrp->info, event->cpu);
-	event->shadow_ctx_time = now - t->timestamp;
-}
-
-static inline void
 perf_cgroup_event_enable(struct perf_event *event, struct perf_event_context *ctx)
 {
 	struct perf_cpu_context *cpuctx;
@@ -1066,7 +1101,8 @@
 {
 }
 
-static inline void update_cgrp_time_from_cpuctx(struct perf_cpu_context *cpuctx)
+static inline void update_cgrp_time_from_cpuctx(struct perf_cpu_context *cpuctx,
+						bool final)
 {
 }
 
@@ -1098,12 +1134,12 @@
 {
 }
 
-static inline void
-perf_cgroup_set_shadow_time(struct perf_event *event, u64 now)
+static inline u64 perf_cgroup_event_time(struct perf_event *event)
 {
+	return 0;
 }
 
-static inline u64 perf_cgroup_event_time(struct perf_event *event)
+static inline u64 perf_cgroup_event_time_now(struct perf_event *event, u64 now)
 {
 	return 0;
 }
@@ -1193,6 +1229,11 @@
 	return 0;
 }
 
+static int perf_mux_hrtimer_restart_ipi(void *arg)
+{
+	return perf_mux_hrtimer_restart(arg);
+}
+
 void perf_pmu_disable(struct pmu *pmu)
 {
 	int *count = this_cpu_ptr(pmu->pmu_disable_count);
@@ -1332,8 +1373,9 @@
  *	  perf_event_context::mutex
  *	    perf_event::child_mutex;
  *	      perf_event_context::lock
- *	    perf_event::mmap_mutex
  *	    mmap_lock
+ *	      perf_event::mmap_mutex
+ *	        perf_buffer::aux_mutex
  *	      perf_addr_filters_head::lock
  *
  *    cpu_hotplug_lock
@@ -1525,22 +1567,59 @@
 /*
  * Update the record of the current time in a context.
  */
-static void update_context_time(struct perf_event_context *ctx)
+static void __update_context_time(struct perf_event_context *ctx, bool adv)
 {
 	u64 now = perf_clock();
 
-	ctx->time += now - ctx->timestamp;
+	if (adv)
+		ctx->time += now - ctx->timestamp;
 	ctx->timestamp = now;
+
+	/*
+	 * The above: time' = time + (now - timestamp), can be re-arranged
+	 * into: time` = now + (time - timestamp), which gives a single value
+	 * offset to compute future time without locks on.
+	 *
+	 * See perf_event_time_now(), which can be used from NMI context where
+	 * it's (obviously) not possible to acquire ctx->lock in order to read
+	 * both the above values in a consistent manner.
+	 */
+	WRITE_ONCE(ctx->timeoffset, ctx->time - ctx->timestamp);
+}
+
+static void update_context_time(struct perf_event_context *ctx)
+{
+	__update_context_time(ctx, true);
 }
 
 static u64 perf_event_time(struct perf_event *event)
 {
 	struct perf_event_context *ctx = event->ctx;
 
+	if (unlikely(!ctx))
+		return 0;
+
 	if (is_cgroup_event(event))
 		return perf_cgroup_event_time(event);
 
-	return ctx ? ctx->time : 0;
+	return ctx->time;
+}
+
+static u64 perf_event_time_now(struct perf_event *event, u64 now)
+{
+	struct perf_event_context *ctx = event->ctx;
+
+	if (unlikely(!ctx))
+		return 0;
+
+	if (is_cgroup_event(event))
+		return perf_cgroup_event_time_now(event, now);
+
+	if (!(__load_acquire(&ctx->is_active) & EVENT_TIME))
+		return ctx->time;
+
+	now += READ_ONCE(ctx->timeoffset);
+	return now;
 }
 
 static enum event_type_t get_event_type(struct perf_event *event)
@@ -1826,28 +1905,34 @@
 					      PERF_EVENT_STATE_INACTIVE;
 }
 
-static void __perf_event_read_size(struct perf_event *event, int nr_siblings)
+static int __perf_event_read_size(u64 read_format, int nr_siblings)
 {
 	int entry = sizeof(u64); /* value */
 	int size = 0;
 	int nr = 1;
 
-	if (event->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
+	if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
 		size += sizeof(u64);
 
-	if (event->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING)
+	if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING)
 		size += sizeof(u64);
 
-	if (event->attr.read_format & PERF_FORMAT_ID)
+	if (read_format & PERF_FORMAT_ID)
+		entry += sizeof(u64);
+
+	if (read_format & PERF_FORMAT_LOST)
 		entry += sizeof(u64);
 
-	if (event->attr.read_format & PERF_FORMAT_GROUP) {
+	if (read_format & PERF_FORMAT_GROUP) {
 		nr += nr_siblings;
 		size += sizeof(u64);
 	}
 
-	size += entry * nr;
-	event->read_size = size;
+	/*
+	 * Since perf_event_validate_size() limits this to 16k and inhibits
+	 * adding more siblings, this will never overflow.
+	 */
+	return size + nr * entry;
 }
 
 static void __perf_event_header_size(struct perf_event *event, u64 sample_type)
@@ -1897,8 +1982,9 @@
  */
 static void perf_event__header_size(struct perf_event *event)
 {
-	__perf_event_read_size(event,
-			       event->group_leader->nr_siblings);
+	event->read_size =
+		__perf_event_read_size(event->attr.read_format,
+				       event->group_leader->nr_siblings);
 	__perf_event_header_size(event, event->attr.sample_type);
 }
 
@@ -1929,23 +2015,44 @@
 	event->id_header_size = size;
 }
 
+/*
+ * Check that adding an event to the group does not result in anybody
+ * overflowing the 64k event limit imposed by the output buffer.
+ *
+ * Specifically, check that the read_size for the event does not exceed 16k,
+ * read_size being the one term that grows with groups size. Since read_size
+ * depends on per-event read_format, also (re)check the existing events.
+ *
+ * This leaves 48k for the constant size fields and things like callchains,
+ * branch stacks and register sets.
+ */
 static bool perf_event_validate_size(struct perf_event *event)
 {
-	/*
-	 * The values computed here will be over-written when we actually
-	 * attach the event.
-	 */
-	__perf_event_read_size(event, event->group_leader->nr_siblings + 1);
-	__perf_event_header_size(event, event->attr.sample_type & ~PERF_SAMPLE_READ);
-	perf_event__id_header_size(event);
+	struct perf_event *sibling, *group_leader = event->group_leader;
+
+	if (__perf_event_read_size(event->attr.read_format,
+				   group_leader->nr_siblings + 1) > 16*1024)
+		return false;
+
+	if (__perf_event_read_size(group_leader->attr.read_format,
+				   group_leader->nr_siblings + 1) > 16*1024)
+		return false;
 
 	/*
-	 * Sum the lot; should not exceed the 64k limit we have on records.
-	 * Conservative limit to allow for callchains and other variable fields.
+	 * When creating a new group leader, group_leader->ctx is initialized
+	 * after the size has been validated, but we cannot safely use
+	 * for_each_sibling_event() until group_leader->ctx is set. A new group
+	 * leader cannot have any siblings yet, so we can safely skip checking
+	 * the non-existent siblings.
 	 */
-	if (event->read_size + event->header_size +
-	    event->id_header_size + sizeof(struct perf_event_header) >= 16*1024)
-		return false;
+	if (event == group_leader)
+		return true;
+
+	for_each_sibling_event(sibling, group_leader) {
+		if (__perf_event_read_size(sibling->attr.read_format,
+					   group_leader->nr_siblings + 1) > 16*1024)
+			return false;
+	}
 
 	return true;
 }
@@ -1973,6 +2080,7 @@
 
 	list_add_tail(&event->sibling_list, &group_leader->sibling_list);
 	group_leader->nr_siblings++;
+	group_leader->group_generation++;
 
 	perf_event__header_size(group_leader);
 
@@ -2165,6 +2273,7 @@
 	if (leader != event) {
 		list_del_init(&event->sibling_list);
 		event->group_leader->nr_siblings--;
+		event->group_leader->group_generation++;
 		goto out;
 	}
 
@@ -2184,7 +2293,7 @@
 		/* Inherit group flags from the previous leader */
 		sibling->group_caps = event->group_caps;
 
-		if (!RB_EMPTY_NODE(&event->group_node)) {
+		if (sibling->attach_state & PERF_ATTACH_CONTEXT) {
 			add_event_to_groups(sibling, event->ctx);
 
 			if (sibling->state == PERF_EVENT_STATE_ACTIVE)
@@ -2285,11 +2394,23 @@
 	event->pmu->del(event, 0);
 	event->oncpu = -1;
 
-	if (READ_ONCE(event->pending_disable) >= 0) {
-		WRITE_ONCE(event->pending_disable, -1);
+	if (event->pending_disable) {
+		event->pending_disable = 0;
 		perf_cgroup_event_disable(event, ctx);
 		state = PERF_EVENT_STATE_OFF;
 	}
+
+	if (event->pending_sigtrap) {
+		event->pending_sigtrap = 0;
+		if (state != PERF_EVENT_STATE_OFF &&
+		    !event->pending_work &&
+		    !task_work_add(current, &event->pending_task, TWA_RESUME)) {
+			event->pending_work = 1;
+		} else {
+			local_dec(&event->ctx->nr_pending);
+		}
+	}
+
 	perf_event_set_state(event, state);
 
 	if (!is_software_event(event))
@@ -2329,6 +2450,7 @@
 
 #define DETACH_GROUP	0x01UL
 #define DETACH_CHILD	0x02UL
+#define DETACH_DEAD	0x04UL
 
 /*
  * Cross CPU call to remove a performance event
@@ -2346,17 +2468,28 @@
 
 	if (ctx->is_active & EVENT_TIME) {
 		update_context_time(ctx);
-		update_cgrp_time_from_cpuctx(cpuctx);
+		update_cgrp_time_from_cpuctx(cpuctx, false);
 	}
 
+	/*
+	 * Ensure event_sched_out() switches to OFF, at the very least
+	 * this avoids raising perf_pending_task() at this time.
+	 */
+	if (flags & DETACH_DEAD)
+		event->pending_disable = 1;
 	event_sched_out(event, cpuctx, ctx);
 	if (flags & DETACH_GROUP)
 		perf_group_detach(event);
 	if (flags & DETACH_CHILD)
 		perf_child_detach(event);
 	list_del_event(event, ctx);
+	if (flags & DETACH_DEAD)
+		event->state = PERF_EVENT_STATE_DEAD;
 
 	if (!ctx->nr_events && ctx->is_active) {
+		if (ctx == &cpuctx->ctx)
+			update_cgrp_time_from_cpuctx(cpuctx, true);
+
 		ctx->is_active = 0;
 		ctx->rotate_necessary = 0;
 		if (ctx->task) {
@@ -2388,7 +2521,11 @@
 	 * event_function_call() user.
 	 */
 	raw_spin_lock_irq(&ctx->lock);
-	if (!ctx->is_active) {
+	/*
+	 * Cgroup events are per-cpu events, and must IPI because of
+	 * cgrp_cpuctx_list.
+	 */
+	if (!ctx->is_active && !is_cgroup_event(event)) {
 		__perf_remove_from_context(event, __get_cpu_context(ctx),
 					   ctx, (void *)flags);
 		raw_spin_unlock_irq(&ctx->lock);
@@ -2434,7 +2571,7 @@
  * hold the top-level event's child_mutex, so any descendant that
  * goes to exit will block in perf_event_exit_event().
  *
- * When called from perf_pending_event it's OK because event->ctx
+ * When called from perf_pending_irq it's OK because event->ctx
  * is the current context on this CPU and preemption is disabled,
  * hence we can't get into perf_event_task_sched_out for this context.
  */
@@ -2473,43 +2610,8 @@
 
 void perf_event_disable_inatomic(struct perf_event *event)
 {
-	WRITE_ONCE(event->pending_disable, smp_processor_id());
-	/* can fail, see perf_pending_event_disable() */
-	irq_work_queue(&event->pending);
-}
-
-static void perf_set_shadow_time(struct perf_event *event,
-				 struct perf_event_context *ctx)
-{
-	/*
-	 * use the correct time source for the time snapshot
-	 *
-	 * We could get by without this by leveraging the
-	 * fact that to get to this function, the caller
-	 * has most likely already called update_context_time()
-	 * and update_cgrp_time_xx() and thus both timestamp
-	 * are identical (or very close). Given that tstamp is,
-	 * already adjusted for cgroup, we could say that:
-	 *    tstamp - ctx->timestamp
-	 * is equivalent to
-	 *    tstamp - cgrp->timestamp.
-	 *
-	 * Then, in perf_output_read(), the calculation would
-	 * work with no changes because:
-	 * - event is guaranteed scheduled in
-	 * - no scheduled out in between
-	 * - thus the timestamp would be the same
-	 *
-	 * But this is a bit hairy.
-	 *
-	 * So instead, we have an explicit cgroup call to remain
-	 * within the time source all along. We believe it
-	 * is cleaner and simpler to understand.
-	 */
-	if (is_cgroup_event(event))
-		perf_cgroup_set_shadow_time(event, event->tstamp);
-	else
-		event->shadow_ctx_time = event->tstamp - ctx->timestamp;
+	event->pending_disable = 1;
+	irq_work_queue(&event->pending_irq);
 }
 
 #define MAX_INTERRUPTS (~0ULL)
@@ -2552,8 +2654,6 @@
 
 	perf_pmu_disable(event->pmu);
 
-	perf_set_shadow_time(event, ctx);
-
 	perf_log_itrace_start(event);
 
 	if (event->pmu->add(event, PERF_EF_START)) {
@@ -2857,11 +2957,14 @@
 	 * perf_event_attr::disabled events will not run and can be initialized
 	 * without IPI. Except when this is the first event for the context, in
 	 * that case we need the magic of the IPI to set ctx->is_active.
+	 * Similarly, cgroup events for the context also needs the IPI to
+	 * manipulate the cgrp_cpuctx_list.
 	 *
 	 * The IOC_ENABLE that is sure to follow the creation of a disabled
 	 * event will issue the IPI and reprogram the hardware.
 	 */
-	if (__perf_effective_state(event) == PERF_EVENT_STATE_OFF && ctx->nr_events) {
+	if (__perf_effective_state(event) == PERF_EVENT_STATE_OFF &&
+	    ctx->nr_events && !is_cgroup_event(event)) {
 		raw_spin_lock_irq(&ctx->lock);
 		if (ctx->task == TASK_TOMBSTONE) {
 			raw_spin_unlock_irq(&ctx->lock);
@@ -3193,6 +3296,15 @@
 	return err;
 }
 
+/*
+ * Copy event-type-independent attributes that may be modified.
+ */
+static void perf_event_modify_copy_attr(struct perf_event_attr *to,
+					const struct perf_event_attr *from)
+{
+	to->sig_data = from->sig_data;
+}
+
 static int perf_event_modify_attr(struct perf_event *event,
 				  struct perf_event_attr *attr)
 {
@@ -3215,10 +3327,17 @@
 	WARN_ON_ONCE(event->ctx->parent_ctx);
 
 	mutex_lock(&event->child_mutex);
+	/*
+	 * Event-type-independent attributes must be copied before event-type
+	 * modification, which will validate that final attributes match the
+	 * source attributes after all relevant attributes have been copied.
+	 */
+	perf_event_modify_copy_attr(&event->attr, attr);
 	err = func(event, attr);
 	if (err)
 		goto out;
 	list_for_each_entry(child, &event->child_list, child_list) {
+		perf_event_modify_copy_attr(&child->attr, attr);
 		err = func(child, attr);
 		if (err)
 			goto out;
@@ -3247,16 +3366,6 @@
 		return;
 	}
 
-	ctx->is_active &= ~event_type;
-	if (!(ctx->is_active & EVENT_ALL))
-		ctx->is_active = 0;
-
-	if (ctx->task) {
-		WARN_ON_ONCE(cpuctx->task_ctx != ctx);
-		if (!ctx->is_active)
-			cpuctx->task_ctx = NULL;
-	}
-
 	/*
 	 * Always update time if it was set; not only when it changes.
 	 * Otherwise we can 'forget' to update time for any but the last
@@ -3270,7 +3379,22 @@
 	if (is_active & EVENT_TIME) {
 		/* update (and stop) ctx time */
 		update_context_time(ctx);
-		update_cgrp_time_from_cpuctx(cpuctx);
+		update_cgrp_time_from_cpuctx(cpuctx, ctx == &cpuctx->ctx);
+		/*
+		 * CPU-release for the below ->is_active store,
+		 * see __load_acquire() in perf_event_time_now()
+		 */
+		barrier();
+	}
+
+	ctx->is_active &= ~event_type;
+	if (!(ctx->is_active & EVENT_ALL))
+		ctx->is_active = 0;
+
+	if (ctx->task) {
+		WARN_ON_ONCE(cpuctx->task_ctx != ctx);
+		if (!ctx->is_active)
+			cpuctx->task_ctx = NULL;
 	}
 
 	is_active ^= ctx->is_active; /* changed bits */
@@ -3444,11 +3568,23 @@
 		raw_spin_lock_nested(&next_ctx->lock, SINGLE_DEPTH_NESTING);
 		if (context_equiv(ctx, next_ctx)) {
 
+			perf_pmu_disable(pmu);
+
+			/* PMIs are disabled; ctx->nr_pending is stable. */
+			if (local_read(&ctx->nr_pending) ||
+			    local_read(&next_ctx->nr_pending)) {
+				/*
+				 * Must not swap out ctx when there's pending
+				 * events that rely on the ctx->task relation.
+				 */
+				raw_spin_unlock(&next_ctx->lock);
+				rcu_read_unlock();
+				goto inside_switch;
+			}
+
 			WRITE_ONCE(ctx->task, next);
 			WRITE_ONCE(next_ctx->task, task);
 
-			perf_pmu_disable(pmu);
-
 			if (cpuctx->sched_cb_usage && pmu->sched_task)
 				pmu->sched_task(ctx, false);
 
@@ -3489,6 +3625,7 @@
 		raw_spin_lock(&ctx->lock);
 		perf_pmu_disable(pmu);
 
+inside_switch:
 		if (cpuctx->sched_cb_usage && pmu->sched_task)
 			pmu->sched_task(ctx, false);
 		task_ctx_sched_out(cpuctx, ctx, EVENT_ALL);
@@ -3707,13 +3844,19 @@
 	return 0;
 }
 
+/*
+ * Because the userpage is strictly per-event (there is no concept of context,
+ * so there cannot be a context indirection), every userpage must be updated
+ * when context time starts :-(
+ *
+ * IOW, we must not miss EVENT_TIME edges.
+ */
 static inline bool event_update_userpage(struct perf_event *event)
 {
 	if (likely(!atomic_read(&event->mmap_count)))
 		return false;
 
 	perf_event_update_time(event);
-	perf_set_shadow_time(event, event->ctx);
 	perf_event_update_userpage(event);
 
 	return true;
@@ -3797,13 +3940,23 @@
 	     struct task_struct *task)
 {
 	int is_active = ctx->is_active;
-	u64 now;
 
 	lockdep_assert_held(&ctx->lock);
 
 	if (likely(!ctx->nr_events))
 		return;
 
+	if (!(is_active & EVENT_TIME)) {
+		/* start ctx time */
+		__update_context_time(ctx, false);
+		perf_cgroup_set_timestamp(task, ctx);
+		/*
+		 * CPU-release for the below ->is_active store,
+		 * see __load_acquire() in perf_event_time_now()
+		 */
+		barrier();
+	}
+
 	ctx->is_active |= (event_type | EVENT_TIME);
 	if (ctx->task) {
 		if (!is_active)
@@ -3814,13 +3967,6 @@
 
 	is_active ^= ctx->is_active; /* changed bits */
 
-	if (is_active & EVENT_TIME) {
-		/* start ctx time */
-		now = perf_clock();
-		ctx->timestamp = now;
-		perf_cgroup_set_timestamp(task, ctx);
-	}
-
 	/*
 	 * First go through the list and put on any pinned groups
 	 * in order to give them the best chance of going on.
@@ -4019,7 +4165,11 @@
 	period = perf_calculate_period(event, nsec, count);
 
 	delta = (s64)(period - hwc->sample_period);
-	delta = (delta + 7) / 8; /* low pass filter */
+	if (delta >= 0)
+		delta += 7;
+	else
+		delta -= 7;
+	delta /= 8; /* low pass filter */
 
 	sample_period = hwc->sample_period + delta;
 
@@ -4414,6 +4564,18 @@
 	return local64_read(&event->count) + atomic64_read(&event->child_count);
 }
 
+static void calc_timer_values(struct perf_event *event,
+				u64 *now,
+				u64 *enabled,
+				u64 *running)
+{
+	u64 ctx_time;
+
+	*now = perf_clock();
+	ctx_time = perf_event_time_now(event, *now);
+	__perf_update_times(event, ctx_time, enabled, running);
+}
+
 /*
  * NMI-safe method to read a local event, that is an event that
  * is:
@@ -4473,10 +4635,9 @@
 
 	*value = local64_read(&event->count);
 	if (enabled || running) {
-		u64 now = event->shadow_ctx_time + perf_clock();
-		u64 __enabled, __running;
+		u64 __enabled, __running, __now;;
 
-		__perf_update_times(event, now, &__enabled, &__running);
+		calc_timer_values(event, &__now, &__enabled, &__running);
 		if (enabled)
 			*enabled = __enabled;
 		if (running)
@@ -4946,9 +5107,35 @@
 static void perf_addr_filters_splice(struct perf_event *event,
 				       struct list_head *head);
 
+static void perf_pending_task_sync(struct perf_event *event)
+{
+	struct callback_head *head = &event->pending_task;
+
+	if (!event->pending_work)
+		return;
+	/*
+	 * If the task is queued to the current task's queue, we
+	 * obviously can't wait for it to complete. Simply cancel it.
+	 */
+	if (task_work_cancel(current, head)) {
+		event->pending_work = 0;
+		local_dec(&event->ctx->nr_pending);
+		return;
+	}
+
+	/*
+	 * All accesses related to the event are within the same
+	 * non-preemptible section in perf_pending_task(). The RCU
+	 * grace period before the event is freed will make sure all
+	 * those accesses are complete by then.
+	 */
+	rcuwait_wait_event(&event->pending_work_wait, !event->pending_work, TASK_UNINTERRUPTIBLE);
+}
+
 static void _free_event(struct perf_event *event)
 {
-	irq_work_sync(&event->pending);
+	irq_work_sync(&event->pending_irq);
+	perf_pending_task_sync(event);
 
 	unaccount_event(event);
 
@@ -5102,9 +5289,7 @@
 
 	ctx = perf_event_ctx_lock(event);
 	WARN_ON_ONCE(ctx->parent_ctx);
-	perf_remove_from_context(event, DETACH_GROUP);
 
-	raw_spin_lock_irq(&ctx->lock);
 	/*
 	 * Mark this event as STATE_DEAD, there is no external reference to it
 	 * anymore.
@@ -5116,14 +5301,14 @@
 	 * Thus this guarantees that we will in fact observe and kill _ALL_
 	 * child events.
 	 */
-	event->state = PERF_EVENT_STATE_DEAD;
-	raw_spin_unlock_irq(&ctx->lock);
+	perf_remove_from_context(event, DETACH_GROUP|DETACH_DEAD);
 
 	perf_event_ctx_unlock(event, ctx);
 
 again:
 	mutex_lock(&event->child_mutex);
 	list_for_each_entry(child, &event->child_list, child_list) {
+		void *var = NULL;
 
 		/*
 		 * Cannot change, child events are not migrated, see the
@@ -5164,11 +5349,23 @@
 			 * this can't be the last reference.
 			 */
 			put_event(event);
+		} else {
+			var = &ctx->refcount;
 		}
 
 		mutex_unlock(&event->child_mutex);
 		mutex_unlock(&ctx->mutex);
 		put_ctx(ctx);
+
+		if (var) {
+			/*
+			 * If perf_event_free_task() has deleted all events from the
+			 * ctx while the child_mutex got released above, make sure to
+			 * notify about the preceding put_ctx().
+			 */
+			smp_mb(); /* pairs with wait_var_event() */
+			wake_up_var(var);
+		}
 		goto again;
 	}
 	mutex_unlock(&event->child_mutex);
@@ -5248,7 +5445,7 @@
 					u64 read_format, u64 *values)
 {
 	struct perf_event_context *ctx = leader->ctx;
-	struct perf_event *sub;
+	struct perf_event *sub, *parent;
 	unsigned long flags;
 	int n = 1; /* skip @nr */
 	int ret;
@@ -5258,6 +5455,33 @@
 		return ret;
 
 	raw_spin_lock_irqsave(&ctx->lock, flags);
+	/*
+	 * Verify the grouping between the parent and child (inherited)
+	 * events is still in tact.
+	 *
+	 * Specifically:
+	 *  - leader->ctx->lock pins leader->sibling_list
+	 *  - parent->child_mutex pins parent->child_list
+	 *  - parent->ctx->mutex pins parent->sibling_list
+	 *
+	 * Because parent->ctx != leader->ctx (and child_list nests inside
+	 * ctx->mutex), group destruction is not atomic between children, also
+	 * see perf_event_release_kernel(). Additionally, parent can grow the
+	 * group.
+	 *
+	 * Therefore it is possible to have parent and child groups in a
+	 * different configuration and summing over such a beast makes no sense
+	 * what so ever.
+	 *
+	 * Reject this.
+	 */
+	parent = leader->parent;
+	if (parent &&
+	    (parent->group_generation != leader->group_generation ||
+	     parent->nr_siblings != leader->nr_siblings)) {
+		ret = -ECHILD;
+		goto unlock;
+	}
 
 	/*
 	 * Since we co-schedule groups, {enabled,running} times of siblings
@@ -5280,15 +5504,20 @@
 	values[n++] += perf_event_count(leader);
 	if (read_format & PERF_FORMAT_ID)
 		values[n++] = primary_event_id(leader);
+	if (read_format & PERF_FORMAT_LOST)
+		values[n++] = atomic64_read(&leader->lost_samples);
 
 	for_each_sibling_event(sub, leader) {
 		values[n++] += perf_event_count(sub);
 		if (read_format & PERF_FORMAT_ID)
 			values[n++] = primary_event_id(sub);
+		if (read_format & PERF_FORMAT_LOST)
+			values[n++] = atomic64_read(&sub->lost_samples);
 	}
 
+unlock:
 	raw_spin_unlock_irqrestore(&ctx->lock, flags);
-	return 0;
+	return ret;
 }
 
 static int perf_read_group(struct perf_event *event,
@@ -5307,10 +5536,6 @@
 
 	values[0] = 1 + leader->nr_siblings;
 
-	/*
-	 * By locking the child_mutex of the leader we effectively
-	 * lock the child list of all siblings.. XXX explain how.
-	 */
 	mutex_lock(&leader->child_mutex);
 
 	ret = __perf_read_group_add(leader, read_format, values);
@@ -5341,7 +5566,7 @@
 				 u64 read_format, char __user *buf)
 {
 	u64 enabled, running;
-	u64 values[4];
+	u64 values[5];
 	int n = 0;
 
 	values[n++] = __perf_event_read_value(event, &enabled, &running);
@@ -5351,6 +5576,8 @@
 		values[n++] = running;
 	if (read_format & PERF_FORMAT_ID)
 		values[n++] = primary_event_id(event);
+	if (read_format & PERF_FORMAT_LOST)
+		values[n++] = atomic64_read(&event->lost_samples);
 
 	if (copy_to_user(buf, values, n * sizeof(u64)))
 		return -EFAULT;
@@ -5551,14 +5778,15 @@
 	if (!value)
 		return -EINVAL;
 
-	if (event->attr.freq && value > sysctl_perf_event_sample_rate)
-		return -EINVAL;
-
-	if (perf_event_check_period(event, value))
-		return -EINVAL;
-
-	if (!event->attr.freq && (value & (1ULL << 63)))
-		return -EINVAL;
+	if (event->attr.freq) {
+		if (value > sysctl_perf_event_sample_rate)
+			return -EINVAL;
+	} else {
+		if (perf_event_check_period(event, value))
+			return -EINVAL;
+		if (value & (1ULL << 63))
+			return -EINVAL;
+	}
 
 	event_function_call(event, __perf_event_period, &value);
 
@@ -5798,18 +6026,6 @@
 	return event->pmu->event_idx(event);
 }
 
-static void calc_timer_values(struct perf_event *event,
-				u64 *now,
-				u64 *enabled,
-				u64 *running)
-{
-	u64 ctx_time;
-
-	*now = perf_clock();
-	ctx_time = event->shadow_ctx_time + *now;
-	__perf_update_times(event, ctx_time, enabled, running);
-}
-
 static void perf_event_init_userpage(struct perf_event *event)
 {
 	struct perf_event_mmap_page *userpg;
@@ -5934,6 +6150,8 @@
 	struct perf_buffer *old_rb = NULL;
 	unsigned long flags;
 
+	WARN_ON_ONCE(event->parent);
+
 	if (event->rb) {
 		/*
 		 * Should be impossible, we set this when removing
@@ -5991,6 +6209,9 @@
 {
 	struct perf_buffer *rb;
 
+	if (event->parent)
+		event = event->parent;
+
 	rcu_read_lock();
 	rb = rcu_dereference(event->rb);
 	if (rb) {
@@ -6004,6 +6225,9 @@
 {
 	struct perf_buffer *rb;
 
+	if (event->parent)
+		event = event->parent;
+
 	rcu_read_lock();
 	rb = rcu_dereference(event->rb);
 	if (rb) {
@@ -6062,12 +6286,11 @@
 		event->pmu->event_unmapped(event, vma->vm_mm);
 
 	/*
-	 * rb->aux_mmap_count will always drop before rb->mmap_count and
-	 * event->mmap_count, so it is ok to use event->mmap_mutex to
-	 * serialize with perf_mmap here.
+	 * The AUX buffer is strictly a sub-buffer, serialize using aux_mutex
+	 * to avoid complications.
 	 */
 	if (rb_has_aux(rb) && vma->vm_pgoff == rb->aux_pgoff &&
-	    atomic_dec_and_mutex_lock(&rb->aux_mmap_count, &event->mmap_mutex)) {
+	    atomic_dec_and_mutex_lock(&rb->aux_mmap_count, &rb->aux_mutex)) {
 		/*
 		 * Stop all AUX events that are writing to this buffer,
 		 * so that we can free its AUX pages and corresponding PMU
@@ -6084,7 +6307,7 @@
 		rb_free_aux(rb);
 		WARN_ON_ONCE(refcount_read(&rb->aux_refcount));
 
-		mutex_unlock(&event->mmap_mutex);
+		mutex_unlock(&rb->aux_mutex);
 	}
 
 	if (atomic_dec_and_test(&rb->mmap_count))
@@ -6172,6 +6395,7 @@
 	struct perf_event *event = file->private_data;
 	unsigned long user_locked, user_lock_limit;
 	struct user_struct *user = current_user();
+	struct mutex *aux_mutex = NULL;
 	struct perf_buffer *rb = NULL;
 	unsigned long locked, lock_limit;
 	unsigned long vma_size;
@@ -6210,6 +6434,8 @@
 			return -EINVAL;
 
 		nr_pages = vma_size / PAGE_SIZE;
+		if (nr_pages > INT_MAX)
+			return -ENOMEM;
 
 		mutex_lock(&event->mmap_mutex);
 		ret = -EINVAL;
@@ -6218,6 +6444,9 @@
 		if (!rb)
 			goto aux_unlock;
 
+		aux_mutex = &rb->aux_mutex;
+		mutex_lock(aux_mutex);
+
 		aux_offset = READ_ONCE(rb->user_page->aux_offset);
 		aux_size = READ_ONCE(rb->user_page->aux_size);
 
@@ -6270,17 +6499,17 @@
 again:
 	mutex_lock(&event->mmap_mutex);
 	if (event->rb) {
-		if (event->rb->nr_pages != nr_pages) {
+		if (data_page_nr(event->rb) != nr_pages) {
 			ret = -EINVAL;
 			goto unlock;
 		}
 
 		if (!atomic_inc_not_zero(&event->rb->mmap_count)) {
 			/*
-			 * Raced against perf_mmap_close() through
-			 * perf_event_set_output(). Try again, hope for better
-			 * luck.
+			 * Raced against perf_mmap_close(); remove the
+			 * event and try again.
 			 */
+			ring_buffer_attach(event, NULL);
 			mutex_unlock(&event->mmap_mutex);
 			goto again;
 		}
@@ -6349,7 +6578,6 @@
 		ring_buffer_attach(event, rb);
 
 		perf_event_update_time(event);
-		perf_set_shadow_time(event, event->ctx);
 		perf_event_init_userpage(event);
 		perf_event_update_userpage(event);
 	} else {
@@ -6369,6 +6597,8 @@
 		atomic_dec(&rb->mmap_count);
 	}
 aux_unlock:
+	if (aux_mutex)
+		mutex_unlock(aux_mutex);
 	mutex_unlock(&event->mmap_mutex);
 
 	/*
@@ -6447,32 +6677,43 @@
 		return;
 
 	/*
-	 * perf_pending_event() can race with the task exiting.
+	 * Both perf_pending_task() and perf_pending_irq() can race with the
+	 * task exiting.
 	 */
 	if (current->flags & PF_EXITING)
 		return;
 
-	force_sig_perf((void __user *)event->pending_addr,
-		       event->attr.type, event->attr.sig_data);
+	send_sig_perf((void __user *)event->pending_addr,
+		      event->attr.type, event->attr.sig_data);
 }
 
-static void perf_pending_event_disable(struct perf_event *event)
+/*
+ * Deliver the pending work in-event-context or follow the context.
+ */
+static void __perf_pending_irq(struct perf_event *event)
 {
-	int cpu = READ_ONCE(event->pending_disable);
+	int cpu = READ_ONCE(event->oncpu);
 
+	/*
+	 * If the event isn't running; we done. event_sched_out() will have
+	 * taken care of things.
+	 */
 	if (cpu < 0)
 		return;
 
+	/*
+	 * Yay, we hit home and are in the context of the event.
+	 */
 	if (cpu == smp_processor_id()) {
-		WRITE_ONCE(event->pending_disable, -1);
-
-		if (event->attr.sigtrap) {
+		if (event->pending_sigtrap) {
+			event->pending_sigtrap = 0;
 			perf_sigtrap(event);
-			atomic_set_release(&event->event_limit, 1); /* rearm event */
-			return;
+			local_dec(&event->ctx->nr_pending);
+		}
+		if (event->pending_disable) {
+			event->pending_disable = 0;
+			perf_event_disable_local(event);
 		}
-
-		perf_event_disable_local(event);
 		return;
 	}
 
@@ -6492,52 +6733,92 @@
 	 *				  irq_work_queue(); // FAILS
 	 *
 	 *  irq_work_run()
-	 *    perf_pending_event()
+	 *    perf_pending_irq()
 	 *
 	 * But the event runs on CPU-B and wants disabling there.
 	 */
-	irq_work_queue_on(&event->pending, cpu);
+	irq_work_queue_on(&event->pending_irq, cpu);
 }
 
-static void perf_pending_event(struct irq_work *entry)
+static void perf_pending_irq(struct irq_work *entry)
 {
-	struct perf_event *event = container_of(entry, struct perf_event, pending);
+	struct perf_event *event = container_of(entry, struct perf_event, pending_irq);
 	int rctx;
 
-	rctx = perf_swevent_get_recursion_context();
 	/*
 	 * If we 'fail' here, that's OK, it means recursion is already disabled
 	 * and we won't recurse 'further'.
 	 */
+	rctx = perf_swevent_get_recursion_context();
 
-	perf_pending_event_disable(event);
-
+	/*
+	 * The wakeup isn't bound to the context of the event -- it can happen
+	 * irrespective of where the event is.
+	 */
 	if (event->pending_wakeup) {
 		event->pending_wakeup = 0;
 		perf_event_wakeup(event);
 	}
 
+	__perf_pending_irq(event);
+
 	if (rctx >= 0)
 		perf_swevent_put_recursion_context(rctx);
 }
 
-/*
+static void perf_pending_task(struct callback_head *head)
+{
+	struct perf_event *event = container_of(head, struct perf_event, pending_task);
+	int rctx;
+
+	/*
+	 * All accesses to the event must belong to the same implicit RCU read-side
+	 * critical section as the ->pending_work reset. See comment in
+	 * perf_pending_task_sync().
+	 */
+	preempt_disable_notrace();
+	/*
+	 * If we 'fail' here, that's OK, it means recursion is already disabled
+	 * and we won't recurse 'further'.
+	 */
+	rctx = perf_swevent_get_recursion_context();
+
+	if (event->pending_work) {
+		event->pending_work = 0;
+		perf_sigtrap(event);
+		local_dec(&event->ctx->nr_pending);
+		rcuwait_wake_up(&event->pending_work_wait);
+	}
+
+	if (rctx >= 0)
+		perf_swevent_put_recursion_context(rctx);
+	preempt_enable_notrace();
+}
+
+/*              
  * We assume there is only KVM supporting the callbacks.
  * Later on, we might change it to a list if there is
  * another virtualization implementation supporting the callbacks.
  */
-struct perf_guest_info_callbacks *perf_guest_cbs;
+struct perf_guest_info_callbacks __rcu *perf_guest_cbs;
 
 int perf_register_guest_info_callbacks(struct perf_guest_info_callbacks *cbs)
 {
-	perf_guest_cbs = cbs;
+	if (WARN_ON_ONCE(rcu_access_pointer(perf_guest_cbs)))
+		return -EBUSY;
+
+	rcu_assign_pointer(perf_guest_cbs, cbs);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(perf_register_guest_info_callbacks);
 
 int perf_unregister_guest_info_callbacks(struct perf_guest_info_callbacks *cbs)
 {
-	perf_guest_cbs = NULL;
+	if (WARN_ON_ONCE(rcu_access_pointer(perf_guest_cbs) != cbs))
+		return -EINVAL;
+
+	rcu_assign_pointer(perf_guest_cbs, NULL);
+	synchronize_rcu();
 	return 0;
 }
 EXPORT_SYMBOL_GPL(perf_unregister_guest_info_callbacks);
@@ -6696,7 +6977,7 @@
 	if (WARN_ON_ONCE(READ_ONCE(sampler->oncpu) != smp_processor_id()))
 		goto out;
 
-	rb = ring_buffer_get(sampler->parent ? sampler->parent : sampler);
+	rb = ring_buffer_get(sampler);
 	if (!rb)
 		goto out;
 
@@ -6762,7 +7043,7 @@
 	if (WARN_ON_ONCE(!sampler || !data->aux_size))
 		return;
 
-	rb = ring_buffer_get(sampler->parent ? sampler->parent : sampler);
+	rb = ring_buffer_get(sampler);
 	if (!rb)
 		return;
 
@@ -6869,7 +7150,7 @@
 				 u64 enabled, u64 running)
 {
 	u64 read_format = event->attr.read_format;
-	u64 values[4];
+	u64 values[5];
 	int n = 0;
 
 	values[n++] = perf_event_count(event);
@@ -6883,6 +7164,8 @@
 	}
 	if (read_format & PERF_FORMAT_ID)
 		values[n++] = primary_event_id(event);
+	if (read_format & PERF_FORMAT_LOST)
+		values[n++] = atomic64_read(&event->lost_samples);
 
 	__output_copy(handle, values, n * sizeof(u64));
 }
@@ -6893,9 +7176,16 @@
 {
 	struct perf_event *leader = event->group_leader, *sub;
 	u64 read_format = event->attr.read_format;
-	u64 values[5];
+	unsigned long flags;
+	u64 values[6];
 	int n = 0;
 
+	/*
+	 * Disabling interrupts avoids all counter scheduling
+	 * (context switches, timer based rotation and IPIs).
+	 */
+	local_irq_save(flags);
+
 	values[n++] = 1 + leader->nr_siblings;
 
 	if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
@@ -6911,6 +7201,8 @@
 	values[n++] = perf_event_count(leader);
 	if (read_format & PERF_FORMAT_ID)
 		values[n++] = primary_event_id(leader);
+	if (read_format & PERF_FORMAT_LOST)
+		values[n++] = atomic64_read(&leader->lost_samples);
 
 	__output_copy(handle, values, n * sizeof(u64));
 
@@ -6924,9 +7216,13 @@
 		values[n++] = perf_event_count(sub);
 		if (read_format & PERF_FORMAT_ID)
 			values[n++] = primary_event_id(sub);
+		if (read_format & PERF_FORMAT_LOST)
+			values[n++] = atomic64_read(&sub->lost_samples);
 
 		__output_copy(handle, values, n * sizeof(u64));
 	}
+
+	local_irq_restore(flags);
 }
 
 #define PERF_FORMAT_TOTAL_TIMES (PERF_FORMAT_TOTAL_TIME_ENABLED|\
@@ -7154,7 +7450,6 @@
 static u64 perf_virt_to_phys(u64 virt)
 {
 	u64 phys_addr = 0;
-	struct page *p = NULL;
 
 	if (!virt)
 		return 0;
@@ -7173,14 +7468,15 @@
 		 * If failed, leave phys_addr as 0.
 		 */
 		if (current->mm != NULL) {
+			struct page *p;
+
 			pagefault_disable();
-			if (get_user_page_fast_only(virt, 0, &p))
+			if (get_user_page_fast_only(virt, 0, &p)) {
 				phys_addr = page_to_phys(p) + virt % PAGE_SIZE;
+				put_page(p);
+			}
 			pagefault_enable();
 		}
-
-		if (p)
-			put_page(p);
 	}
 
 	return phys_addr;
@@ -8897,7 +9193,7 @@
 
 	perf_event_header__init_id(&bpf_event->event_id.header,
 				   &sample, event);
-	ret = perf_output_begin(&handle, data, event,
+	ret = perf_output_begin(&handle, &sample, event,
 				bpf_event->event_id.header.size);
 	if (ret)
 		return;
@@ -8914,21 +9210,19 @@
 	bool unregister = type == PERF_BPF_EVENT_PROG_UNLOAD;
 	int i;
 
-	if (prog->aux->func_cnt == 0) {
-		perf_event_ksymbol(PERF_RECORD_KSYMBOL_TYPE_BPF,
-				   (u64)(unsigned long)prog->bpf_func,
-				   prog->jited_len, unregister,
-				   prog->aux->ksym.name);
-	} else {
-		for (i = 0; i < prog->aux->func_cnt; i++) {
-			struct bpf_prog *subprog = prog->aux->func[i];
-
-			perf_event_ksymbol(
-				PERF_RECORD_KSYMBOL_TYPE_BPF,
-				(u64)(unsigned long)subprog->bpf_func,
-				subprog->jited_len, unregister,
-				prog->aux->ksym.name);
-		}
+	perf_event_ksymbol(PERF_RECORD_KSYMBOL_TYPE_BPF,
+			   (u64)(unsigned long)prog->bpf_func,
+			   prog->jited_len, unregister,
+			   prog->aux->ksym.name);
+
+	for (i = 1; i < prog->aux->func_cnt; i++) {
+		struct bpf_prog *subprog = prog->aux->func[i];
+
+		perf_event_ksymbol(
+			PERF_RECORD_KSYMBOL_TYPE_BPF,
+			(u64)(unsigned long)subprog->bpf_func,
+			subprog->jited_len, unregister,
+			subprog->aux->ksym.name);
 	}
 }
 
@@ -9112,8 +9406,8 @@
 		hwc->interrupts = 1;
 	} else {
 		hwc->interrupts++;
-		if (unlikely(throttle
-			     && hwc->interrupts >= max_samples_per_tick)) {
+		if (unlikely(throttle &&
+			     hwc->interrupts > max_samples_per_tick)) {
 			__this_cpu_inc(perf_throttled_count);
 			tick_dep_set_cpu(smp_processor_id(), TICK_DEP_BIT_PERF_EVENTS);
 			hwc->interrupts = MAX_INTERRUPTS;
@@ -9145,8 +9439,8 @@
  */
 
 static int __perf_event_overflow(struct perf_event *event,
-				   int throttle, struct perf_sample_data *data,
-				   struct pt_regs *regs)
+				 int throttle, struct perf_sample_data *data,
+				 struct pt_regs *regs)
 {
 	int events = atomic_read(&event->event_limit);
 	int ret = 0;
@@ -9169,24 +9463,49 @@
 	if (events && atomic_dec_and_test(&event->event_limit)) {
 		ret = 1;
 		event->pending_kill = POLL_HUP;
-		event->pending_addr = data->addr;
-
 		perf_event_disable_inatomic(event);
 	}
 
+	if (event->attr.sigtrap) {
+		unsigned int pending_id = 1;
+
+		if (regs)
+			pending_id = hash32_ptr((void *)instruction_pointer(regs)) ?: 1;
+		if (!event->pending_sigtrap) {
+			event->pending_sigtrap = pending_id;
+			local_inc(&event->ctx->nr_pending);
+		} else if (event->attr.exclude_kernel) {
+			/*
+			 * Should not be able to return to user space without
+			 * consuming pending_sigtrap; with exceptions:
+			 *
+			 *  1. Where !exclude_kernel, events can overflow again
+			 *     in the kernel without returning to user space.
+			 *
+			 *  2. Events that can overflow again before the IRQ-
+			 *     work without user space progress (e.g. hrtimer).
+			 *     To approximate progress (with false negatives),
+			 *     check 32-bit hash of the current IP.
+			 */
+			WARN_ON_ONCE(event->pending_sigtrap != pending_id);
+		}
+		event->pending_addr = data->addr;
+		irq_work_queue(&event->pending_irq);
+	}
+
 	READ_ONCE(event->overflow_handler)(event, data, regs);
 
 	if (*perf_event_fasync(event) && event->pending_kill) {
 		event->pending_wakeup = 1;
-		irq_work_queue(&event->pending);
+		irq_work_queue(&event->pending_irq);
 	}
 
 	return ret;
 }
 
 int perf_event_overflow(struct perf_event *event,
-			  struct perf_sample_data *data,
-			  struct pt_regs *regs)
+			struct perf_sample_data *data,
+			struct pt_regs *regs)
 {
 	return __perf_event_overflow(event, 1, data, regs);
 }
@@ -9729,6 +10048,9 @@
 				continue;
 			if (event->attr.config != entry->type)
 				continue;
+			/* Cannot deliver synchronous signal to other task. */
+			if (event->attr.sigtrap)
+				continue;
 			if (perf_tp_event_match(event, &data, regs))
 				perf_swevent_event(event, count, &data, regs);
 		}
@@ -10443,8 +10765,11 @@
 			}
 
 			/* ready to consume more filters */
+			kfree(filename);
+			filename = NULL;
 			state = IF_STATE_ACTION;
 			filter = NULL;
+			kernel = 0;
 		}
 	}
 
@@ -10947,8 +11272,7 @@
 		cpuctx = per_cpu_ptr(pmu->pmu_cpu_context, cpu);
 		cpuctx->hrtimer_interval = ns_to_ktime(NSEC_PER_MSEC * timer);
 
-		cpu_function_call(cpu,
-			(remote_function_f)perf_mux_hrtimer_restart, cpuctx);
+		cpu_function_call(cpu, perf_mux_hrtimer_restart_ipi, cpuctx);
 	}
 	cpus_read_unlock();
 	mutex_unlock(&mux_interval_mutex);
@@ -10960,9 +11284,30 @@
 static struct attribute *pmu_dev_attrs[] = {
 	&dev_attr_type.attr,
 	&dev_attr_perf_event_mux_interval_ms.attr,
+	&dev_attr_nr_addr_filters.attr,
+	NULL,
+};
+
+static umode_t pmu_dev_is_visible(struct kobject *kobj, struct attribute *a, int n)
+{
+	struct device *dev = kobj_to_dev(kobj);
+	struct pmu *pmu = dev_get_drvdata(dev);
+
+	if (n == 2 && !pmu->nr_addr_filters)
+		return 0;
+
+	return a->mode;
+}
+
+static struct attribute_group pmu_dev_attr_group = {
+	.is_visible = pmu_dev_is_visible,
+	.attrs = pmu_dev_attrs,
+};
+
+static const struct attribute_group *pmu_dev_groups[] = {
+	&pmu_dev_attr_group,
 	NULL,
 };
-ATTRIBUTE_GROUPS(pmu_dev);
 
 static int pmu_bus_running;
 static struct bus_type pmu_bus = {
@@ -10985,29 +11330,24 @@
 
 	pmu->dev->groups = pmu->attr_groups;
 	device_initialize(pmu->dev);
-	ret = dev_set_name(pmu->dev, "%s", pmu->name);
-	if (ret)
-		goto free_dev;
 
 	dev_set_drvdata(pmu->dev, pmu);
 	pmu->dev->bus = &pmu_bus;
 	pmu->dev->release = pmu_dev_release;
-	ret = device_add(pmu->dev);
+
+	ret = dev_set_name(pmu->dev, "%s", pmu->name);
 	if (ret)
 		goto free_dev;
 
-	/* For PMUs with address filters, throw in an extra attribute: */
-	if (pmu->nr_addr_filters)
-		ret = device_create_file(pmu->dev, &dev_attr_nr_addr_filters);
-
+	ret = device_add(pmu->dev);
 	if (ret)
-		goto del_dev;
+		goto free_dev;
 
-	if (pmu->attr_update)
+	if (pmu->attr_update) {
 		ret = sysfs_update_groups(&pmu->dev->kobj, pmu->attr_update);
-
-	if (ret)
-		goto del_dev;
+		if (ret)
+			goto del_dev;
+	}
 
 out:
 	return ret;
@@ -11486,8 +11826,9 @@
 
 
 	init_waitqueue_head(&event->waitq);
-	event->pending_disable = -1;
-	init_irq_work(&event->pending, perf_pending_event);
+	init_irq_work(&event->pending_irq, perf_pending_irq);
+	init_task_work(&event->pending_task, perf_pending_task);
+	rcuwait_init(&event->pending_work_wait);
 
 	mutex_init(&event->mmap_mutex);
 	raw_spin_lock_init(&event->addr_filters.lock);
@@ -11506,8 +11847,8 @@
 
 	event->state		= PERF_EVENT_STATE_INACTIVE;
 
-	if (event->attr.sigtrap)
-		atomic_set(&event->event_limit, 1);
+	if (parent_event)
+		event->event_caps = parent_event->event_caps;
 
 	if (task) {
 		event->attach_state = PERF_ATTACH_TASK;
@@ -11799,14 +12140,25 @@
 	goto out;
 }
 
+static void mutex_lock_double(struct mutex *a, struct mutex *b)
+{
+	if (b < a)
+		swap(a, b);
+
+	mutex_lock(a);
+	mutex_lock_nested(b, SINGLE_DEPTH_NESTING);
+}
+
 static int
 perf_event_set_output(struct perf_event *event, struct perf_event *output_event)
 {
 	struct perf_buffer *rb = NULL;
 	int ret = -EINVAL;
 
-	if (!output_event)
+	if (!output_event) {
+		mutex_lock(&event->mmap_mutex);
 		goto set;
+	}
 
 	/* don't allow circular references */
 	if (event == output_event)
@@ -11821,7 +12173,7 @@
 	/*
 	 * If its not a per-cpu rb, it must be the same task.
 	 */
-	if (output_event->cpu == -1 && output_event->ctx != event->ctx)
+	if (output_event->cpu == -1 && output_event->hw.target != event->hw.target)
 		goto out;
 
 	/*
@@ -11844,8 +12196,15 @@
 	    event->pmu != output_event->pmu)
 		goto out;
 
+	/*
+	 * Hold both mmap_mutex to serialize against perf_mmap_close().  Since
+	 * output_event is already on rb->event_list, and the list iteration
+	 * restarts after every removal, it is guaranteed this new event is
+	 * observed *OR* if output_event is already removed, it's guaranteed we
+	 * observe !rb->mmap_count.
+	 */
+	mutex_lock_double(&event->mmap_mutex, &output_event->mmap_mutex);
 set:
-	mutex_lock(&event->mmap_mutex);
 	/* Can't redirect output if we've got an active mmap() */
 	if (atomic_read(&event->mmap_count))
 		goto unlock;
@@ -11855,6 +12214,12 @@
 		rb = ring_buffer_get(output_event);
 		if (!rb)
 			goto unlock;
+
+		/* did we race against perf_mmap_close() */
+		if (!atomic_read(&rb->mmap_count)) {
+			ring_buffer_put(rb);
+			goto unlock;
+		}
 	}
 
 	ring_buffer_attach(event, rb);
@@ -11862,20 +12227,13 @@
 	ret = 0;
 unlock:
 	mutex_unlock(&event->mmap_mutex);
+	if (output_event)
+		mutex_unlock(&output_event->mmap_mutex);
 
 out:
 	return ret;
 }
 
-static void mutex_lock_double(struct mutex *a, struct mutex *b)
-{
-	if (b < a)
-		swap(a, b);
-
-	mutex_lock(a);
-	mutex_lock_nested(b, SINGLE_DEPTH_NESTING);
-}
-
 static int perf_event_set_clock(struct perf_event *event, clockid_t clk_id)
 {
 	bool nmi_safe = false;
@@ -12006,12 +12364,15 @@
 	if (flags & ~PERF_FLAG_ALL)
 		return -EINVAL;
 
-	/* Do we allow access to perf_event_open(2) ? */
-	err = security_perf_event_open(&attr, PERF_SECURITY_OPEN);
+	if (perf_paranoid_any() && !capable(CAP_SYS_ADMIN))
+		return -EACCES;
+
+	err = perf_copy_attr(attr_uptr, &attr);
 	if (err)
 		return err;
 
-	err = perf_copy_attr(attr_uptr, &attr);
+	/* Do we allow access to perf_event_open(2) ? */
+	err = security_perf_event_open(&attr, PERF_SECURITY_OPEN);
 	if (err)
 		return err;
 
@@ -12190,6 +12551,9 @@
 		 * Do not allow to attach to a group in a different task
 		 * or CPU context. If we're moving SW events, we'll fix
 		 * this up later, so allow that.
+		 *
+		 * Racy, not holding group_leader->ctx->mutex, see comment with
+		 * perf_event_ctx_lock().
 		 */
 		if (!move_group && group_leader->ctx != ctx)
 			goto err_context;
@@ -12255,6 +12619,7 @@
 			} else {
 				perf_event_ctx_unlock(group_leader, gctx);
 				move_group = 0;
+				goto not_move_group;
 			}
 		}
 
@@ -12271,7 +12636,17 @@
 		}
 	} else {
 		mutex_lock(&ctx->mutex);
+
+		/*
+		 * Now that we hold ctx->lock, (re)validate group_leader->ctx == ctx,
+		 * see the group_leader && !move_group test earlier.
+		 */
+		if (group_leader && group_leader->ctx != ctx) {
+			err = -EINVAL;
+			goto err_locked;
+		}
 	}
+not_move_group:
 
 	if (ctx->task == TASK_TOMBSTONE) {
 		err = -ESRCH;
@@ -13024,6 +13399,8 @@
 		    !perf_get_aux_event(child_ctr, leader))
 			return -EINVAL;
 	}
+	if (leader)
+		leader->group_generation = parent_event->group_generation;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/events/internal.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/events/internal.h
@@ -40,6 +40,7 @@
 	struct user_struct		*mmap_user;
 
 	/* AUX area */
+	struct mutex			aux_mutex;
 	long				aux_head;
 	unsigned int			aux_nest;
 	long				aux_wakeup;	/* last aux_watermark boundary crossed by aux_head */
@@ -116,6 +117,11 @@
 }
 #endif
 
+static inline int data_page_nr(struct perf_buffer *rb)
+{
+	return rb->nr_pages << page_order(rb);
+}
+
 static inline unsigned long perf_data_size(struct perf_buffer *rb)
 {
 	return rb->nr_pages << (PAGE_SHIFT + page_order(rb));
@@ -123,7 +129,7 @@
 
 static inline unsigned long perf_aux_size(struct perf_buffer *rb)
 {
-	return rb->aux_nr_pages << PAGE_SHIFT;
+	return (unsigned long)rb->aux_nr_pages << PAGE_SHIFT;
 }
 
 #define __DEFINE_OUTPUT_COPY_BODY(advance_buf, memcpy_func, ...)	\
@@ -205,12 +211,7 @@
 
 static inline int get_recursion_context(int *recursion)
 {
-	unsigned int pc = preempt_count();
-	unsigned char rctx = 0;
-
-	rctx += !!(pc & (NMI_MASK));
-	rctx += !!(pc & (NMI_MASK | HARDIRQ_MASK));
-	rctx += !!(pc & (NMI_MASK | HARDIRQ_MASK | SOFTIRQ_OFFSET));
+	unsigned char rctx = interrupt_context_level();
 
 	if (recursion[rctx])
 		return -1;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/events/ring_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/events/ring_buffer.c
@@ -19,10 +19,10 @@
 
 static void perf_output_wakeup(struct perf_output_handle *handle)
 {
-	atomic_set(&handle->rb->poll, EPOLLIN);
+	atomic_set(&handle->rb->poll, EPOLLIN | EPOLLRDNORM);
 
 	handle->event->pending_wakeup = 1;
-	irq_work_queue(&handle->event->pending);
+	irq_work_queue(&handle->event->pending_irq);
 }
 
 /*
@@ -172,8 +172,10 @@
 		goto out;
 
 	if (unlikely(rb->paused)) {
-		if (rb->nr_pages)
+		if (rb->nr_pages) {
 			local_inc(&rb->lost);
+			atomic64_inc(&event->lost_samples);
+		}
 		goto out;
 	}
 
@@ -254,6 +256,7 @@
 
 fail:
 	local_inc(&rb->lost);
+	atomic64_inc(&event->lost_samples);
 	perf_output_put_handle(handle);
 out:
 	rcu_read_unlock();
@@ -329,6 +332,8 @@
 	 */
 	if (!rb->nr_pages)
 		rb->paused = 1;
+
+	mutex_init(&rb->aux_mutex);
 }
 
 void perf_aux_output_flag(struct perf_output_handle *handle, u64 flags)
@@ -680,7 +685,9 @@
 		 * max_order, to aid PMU drivers in double buffering.
 		 */
 		if (!watermark)
-			watermark = nr_pages << (PAGE_SHIFT - 1);
+			watermark = min_t(unsigned long,
+					  U32_MAX,
+					  (unsigned long)nr_pages << (PAGE_SHIFT - 1));
 
 		/*
 		 * Use aux_watermark as the basis for chunking to
@@ -696,6 +703,12 @@
 		watermark = 0;
 	}
 
+	/*
+	 * kcalloc_node() is unable to allocate buffer if the size is larger
+	 * than: PAGE_SIZE << MAX_ORDER; directly bail out in this case.
+	 */
+	if (get_order((unsigned long)nr_pages * sizeof(void *)) > MAX_ORDER)
+		return -ENOMEM;
 	rb->aux_pages = kcalloc_node(nr_pages, sizeof(void *), GFP_KERNEL,
 				     node);
 	if (!rb->aux_pages)
@@ -859,11 +872,6 @@
 }
 
 #else
-static int data_page_nr(struct perf_buffer *rb)
-{
-	return rb->nr_pages << page_order(rb);
-}
-
 static struct page *
 __perf_mmap_to_page(struct perf_buffer *rb, unsigned long pgoff)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/events/uprobes.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/events/uprobes.c
@@ -1484,7 +1484,7 @@
 	uprobe_opcode_t insn = UPROBE_SWBP_INSN;
 	struct xol_area *area;
 
-	area = kmalloc(sizeof(*area), GFP_KERNEL);
+	area = kzalloc(sizeof(*area), GFP_KERNEL);
 	if (unlikely(!area))
 		goto out;
 
@@ -1494,9 +1494,8 @@
 		goto free_area;
 
 	area->xol_mapping.name = "[uprobes]";
-	area->xol_mapping.fault = NULL;
 	area->xol_mapping.pages = area->pages;
-	area->pages[0] = alloc_page(GFP_HIGHUSER);
+	area->pages[0] = alloc_page(GFP_HIGHUSER | __GFP_ZERO);
 	if (!area->pages[0])
 		goto free_bitmap;
 	area->pages[1] = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/exit.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/exit.c
@@ -64,11 +64,58 @@
 #include <linux/rcuwait.h>
 #include <linux/compat.h>
 #include <linux/io_uring.h>
+#include <linux/sysfs.h>
 
 #include <linux/uaccess.h>
 #include <asm/unistd.h>
 #include <asm/mmu_context.h>
 
+/*
+ * The default value should be high enough to not crash a system that randomly
+ * crashes its kernel from time to time, but low enough to at least not permit
+ * overflowing 32-bit refcounts or the ldsem writer count.
+ */
+static unsigned int oops_limit = 10000;
+
+#ifdef CONFIG_SYSCTL
+static struct ctl_table kern_exit_table[] = {
+	{
+		.procname       = "oops_limit",
+		.data           = &oops_limit,
+		.maxlen         = sizeof(oops_limit),
+		.mode           = 0644,
+		.proc_handler   = proc_douintvec,
+	},
+	{ }
+};
+
+static __init int kernel_exit_sysctls_init(void)
+{
+	register_sysctl_init("kernel", kern_exit_table);
+	return 0;
+}
+late_initcall(kernel_exit_sysctls_init);
+#endif
+
+static atomic_t oops_count = ATOMIC_INIT(0);
+
+#ifdef CONFIG_SYSFS
+static ssize_t oops_count_show(struct kobject *kobj, struct kobj_attribute *attr,
+			       char *page)
+{
+	return sysfs_emit(page, "%d\n", atomic_read(&oops_count));
+}
+
+static struct kobj_attribute oops_count_attr = __ATTR_RO(oops_count);
+
+static __init int kernel_exit_sysfs_init(void)
+{
+	sysfs_add_file_to_group(kernel_kobj, &oops_count_attr.attr, NULL);
+	return 0;
+}
+late_initcall(kernel_exit_sysfs_init);
+#endif
+
 static void __unhash_process(struct task_struct *p, bool group_dead)
 {
 	nr_threads--;
@@ -385,6 +432,8 @@
 	 * Search through everything else, we should not get here often.
 	 */
 	for_each_process(g) {
+		if (atomic_read(&mm->mm_users) <= 1)
+			break;
 		if (g->flags & PF_KTHREAD)
 			continue;
 		for_each_thread(g, c) {
@@ -796,7 +845,7 @@
 
 #ifdef CONFIG_POSIX_TIMERS
 		hrtimer_cancel(&tsk->signal->real_timer);
-		exit_itimers(tsk->signal);
+		exit_itimers(tsk);
 #endif
 		if (tsk->mm)
 			setmax_mm_hiwater_rss(&tsk->signal->maxrss, tsk->mm);
@@ -877,6 +926,31 @@
 }
 EXPORT_SYMBOL_GPL(do_exit);
 
+void __noreturn make_task_dead(int signr)
+{
+	/*
+	 * Take the task off the cpu after something catastrophic has
+	 * happened.
+	 */
+	unsigned int limit;
+
+	/*
+	 * Every time the system oopses, if the oops happens while a reference
+	 * to an object was held, the reference leaks.
+	 * If the oops doesn't also leak memory, repeated oopsing can cause
+	 * reference counters to wrap around (if they're not using refcount_t).
+	 * This means that repeated oopsing can make unexploitable-looking bugs
+	 * exploitable through repeated oopsing.
+	 * To make sure this can't happen, place an upper bound on how often the
+	 * kernel may oops without panic().
+	 */
+	limit = READ_ONCE(oops_limit);
+	if (atomic_inc_return(&oops_count) >= limit && limit)
+		panic("Oopsed too often (kernel.oops_limit is %d)", limit);
+
+	do_exit(signr);
+}
+
 void complete_and_exit(struct completion *comp, long code)
 {
 	if (comp)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/fail_function.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/fail_function.c
@@ -163,10 +163,7 @@
 
 static void fei_debugfs_remove_attr(struct fei_attr *attr)
 {
-	struct dentry *dir;
-
-	dir = debugfs_lookup(attr->kp.symbol_name, fei_debugfs_dir);
-	debugfs_remove_recursive(dir);
+	debugfs_lookup_and_remove(attr->kp.symbol_name, fei_debugfs_dir);
 }
 
 static int fei_kprobe_handler(struct kprobe *kp, struct pt_regs *regs)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/fork.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/fork.c
@@ -97,6 +97,7 @@
 #include <linux/scs.h>
 #include <linux/io_uring.h>
 #include <linux/bpf.h>
+#include <linux/tick.h>
 
 #include <asm/pgalloc.h>
 #include <linux/uaccess.h>
@@ -108,6 +109,11 @@
 
 #define CREATE_TRACE_POINTS
 #include <trace/events/task.h>
+#ifdef CONFIG_USER_NS
+extern int unprivileged_userns_clone;
+#else
+#define unprivileged_userns_clone 0
+#endif
 
 /*
  * Minimum number of threads to boot the kernel
@@ -446,6 +452,9 @@
 
 void free_task(struct task_struct *tsk)
 {
+#ifdef CONFIG_SECCOMP
+	WARN_ON_ONCE(tsk->seccomp.filter);
+#endif
 	release_user_cpus_ptr(tsk);
 	scs_release(tsk);
 
@@ -467,6 +476,7 @@
 	arch_release_task_struct(tsk);
 	if (tsk->flags & PF_KTHREAD)
 		free_kthread_struct(tsk);
+	bpf_task_storage_free(tsk);
 	free_task_struct(tsk);
 }
 EXPORT_SYMBOL(free_task);
@@ -573,7 +583,7 @@
 		if (file) {
 			struct address_space *mapping = file->f_mapping;
 
-			get_file(file);
+			vma_get_file(tmp);
 			i_mmap_lock_write(mapping);
 			if (tmp->vm_flags & VM_SHARED)
 				mapping_allow_writable(mapping);
@@ -750,7 +760,6 @@
 	cgroup_free(tsk);
 	task_numa_free(tsk, true);
 	security_task_free(tsk);
-	bpf_task_storage_free(tsk);
 	exit_creds(tsk);
 	delayacct_tsk_free(tsk);
 	put_signal_struct(tsk->signal);
@@ -761,6 +770,14 @@
 }
 EXPORT_SYMBOL_GPL(__put_task_struct);
 
+void __put_task_struct_rcu_cb(struct rcu_head *rhp)
+{
+	struct task_struct *task = container_of(rhp, struct task_struct, rcu);
+
+	__put_task_struct(task);
+}
+EXPORT_SYMBOL_GPL(__put_task_struct_rcu_cb);
+
 void __init __weak arch_task_cache_init(void) { }
 
 /*
@@ -1153,6 +1170,7 @@
 		schedule_work(&mm->async_put_work);
 	}
 }
+EXPORT_SYMBOL(mmput_async);
 #endif
 
 /**
@@ -1535,28 +1553,25 @@
 static int copy_files(unsigned long clone_flags, struct task_struct *tsk)
 {
 	struct files_struct *oldf, *newf;
-	int error = 0;
 
 	/*
 	 * A background process may not have any files ...
 	 */
 	oldf = current->files;
 	if (!oldf)
-		goto out;
+		return 0;
 
 	if (clone_flags & CLONE_FILES) {
 		atomic_inc(&oldf->count);
-		goto out;
+		return 0;
 	}
 
-	newf = dup_fd(oldf, NR_OPEN_MAX, &error);
-	if (!newf)
-		goto out;
+	newf = dup_fd(oldf, NULL);
+	if (IS_ERR(newf))
+		return PTR_ERR(newf);
 
 	tsk->files = newf;
-	error = 0;
-out:
-	return error;
+	return 0;
 }
 
 static int copy_io(unsigned long clone_flags, struct task_struct *tsk)
@@ -1950,6 +1965,10 @@
 	if ((clone_flags & (CLONE_NEWUSER|CLONE_FS)) == (CLONE_NEWUSER|CLONE_FS))
 		return ERR_PTR(-EINVAL);
 
+	if ((clone_flags & CLONE_NEWUSER) && !unprivileged_userns_clone)
+		if (!capable(CAP_SYS_ADMIN))
+			return ERR_PTR(-EPERM);
+
 	/*
 	 * Thread groups must share signals as well, and detached threads
 	 * can only be started up within the thread group.
@@ -2055,18 +2074,18 @@
 #ifdef CONFIG_PROVE_LOCKING
 	DEBUG_LOCKS_WARN_ON(!p->softirqs_enabled);
 #endif
+	retval = copy_creds(p, clone_flags);
+	if (retval < 0)
+		goto bad_fork_free;
+
 	retval = -EAGAIN;
 	if (is_ucounts_overlimit(task_ucounts(p), UCOUNT_RLIMIT_NPROC, rlimit(RLIMIT_NPROC))) {
 		if (p->real_cred->user != INIT_USER &&
 		    !capable(CAP_SYS_RESOURCE) && !capable(CAP_SYS_ADMIN))
-			goto bad_fork_free;
+			goto bad_fork_cleanup_count;
 	}
 	current->flags &= ~PF_NPROC_EXCEEDED;
 
-	retval = copy_creds(p, clone_flags);
-	if (retval < 0)
-		goto bad_fork_free;
-
 	/*
 	 * If multiple threads are within copy_process(), then this check
 	 * triggers too late. This doesn't hurt, the check is only there
@@ -2117,6 +2136,7 @@
 	acct_clear_integrals(p);
 
 	posix_cputimers_init(&p->posix_cputimers);
+	tick_dep_init_task(p);
 
 	p->io_context = NULL;
 	audit_set_context(p, NULL);
@@ -2280,6 +2300,7 @@
 	p->pdeath_signal = 0;
 	INIT_LIST_HEAD(&p->thread_group);
 	p->task_works = NULL;
+	clear_posix_cputimers_work(p);
 
 #ifdef CONFIG_KRETPROBES
 	p->kretprobe_instances.first = NULL;
@@ -2296,6 +2317,17 @@
 		goto bad_fork_put_pidfd;
 
 	/*
+	 * Now that the cgroups are pinned, re-clone the parent cgroup and put
+	 * the new task on the correct runqueue. All this *before* the task
+	 * becomes visible.
+	 *
+	 * This isn't part of ->can_fork() because while the re-cloning is
+	 * cgroup specific, it unconditionally needs to place the task on a
+	 * runqueue.
+	 */
+	sched_cgroup_fork(p, args);
+
+	/*
 	 * From this point on we must avoid any synchronous user-space
 	 * communication until we take the tasklist-lock. In particular, we do
 	 * not want user-space to be able to predict the process start-time by
@@ -2332,12 +2364,6 @@
 
 	spin_lock(&current->sighand->siglock);
 
-	/*
-	 * Copy seccomp details explicitly here, in case they were changed
-	 * before holding sighand lock.
-	 */
-	copy_seccomp(p);
-
 	rseq_fork(p, clone_flags);
 
 	/* Don't start children in a dying pid namespace */
@@ -2352,9 +2378,13 @@
 		goto bad_fork_cancel_cgroup;
 	}
 
-	/* past the last point of failure */
-	if (pidfile)
-		fd_install(pidfd, pidfile);
+	/* No more failure paths after this point. */
+
+	/*
+	 * Copy seccomp details explicitly here, in case they were changed
+	 * before holding sighand lock.
+	 */
+	copy_seccomp(p);
 
 	init_task_pid_links(p);
 	if (likely(p->pid)) {
@@ -2404,6 +2434,9 @@
 	syscall_tracepoint_update(p);
 	write_unlock_irq(&tasklist_lock);
 
+	if (pidfile)
+		fd_install(pidfd, pidfile);
+
 	proc_fork_connector(p);
 	sched_post_fork(p);
 	cgroup_post_fork(p, args);
@@ -2505,11 +2538,6 @@
 	return task;
 }
 
-struct mm_struct *copy_init_mm(void)
-{
-	return dup_mm(NULL, &init_mm);
-}
-
 /*
  * This is like kernel_clone(), but shaved down and tailored to just
  * creating io_uring workers. It returns a created task, or an error pointer.
@@ -2812,7 +2840,7 @@
 	 * - make the CLONE_DETACHED bit reusable for clone3
 	 * - make the CSIGNAL bits reusable for clone3
 	 */
-	if (kargs->flags & (CLONE_DETACHED | CSIGNAL))
+	if (kargs->flags & (CLONE_DETACHED | (CSIGNAL & (~CLONE_NEWTIME))))
 		return false;
 
 	if ((kargs->flags & (CLONE_SIGHAND | CLONE_CLEAR_SIGHAND)) ==
@@ -2904,10 +2932,27 @@
 	init_waitqueue_head(&sighand->signalfd_wqh);
 }
 
-void __init proc_caches_init(void)
+void __init mm_cache_init(void)
 {
 	unsigned int mm_size;
 
+	/*
+	 * The mm_cpumask is located at the end of mm_struct, and is
+	 * dynamically sized based on the maximum CPU number this system
+	 * can have, taking hotplug into account (nr_cpu_ids).
+	 */
+	mm_size = sizeof(struct mm_struct) + cpumask_size();
+
+	mm_cachep = kmem_cache_create_usercopy("mm_struct",
+			mm_size, ARCH_MIN_MMSTRUCT_ALIGN,
+			SLAB_HWCACHE_ALIGN|SLAB_PANIC|SLAB_ACCOUNT,
+			offsetof(struct mm_struct, saved_auxv),
+			sizeof_field(struct mm_struct, saved_auxv),
+			NULL);
+}
+
+void __init proc_caches_init(void)
+{
 	sighand_cachep = kmem_cache_create("sighand_cache",
 			sizeof(struct sighand_struct), 0,
 			SLAB_HWCACHE_ALIGN|SLAB_PANIC|SLAB_TYPESAFE_BY_RCU|
@@ -2925,19 +2970,6 @@
 			SLAB_HWCACHE_ALIGN|SLAB_PANIC|SLAB_ACCOUNT,
 			NULL);
 
-	/*
-	 * The mm_cpumask is located at the end of mm_struct, and is
-	 * dynamically sized based on the maximum CPU number this system
-	 * can have, taking hotplug into account (nr_cpu_ids).
-	 */
-	mm_size = sizeof(struct mm_struct) + cpumask_size();
-
-	mm_cachep = kmem_cache_create_usercopy("mm_struct",
-			mm_size, ARCH_MIN_MMSTRUCT_ALIGN,
-			SLAB_HWCACHE_ALIGN|SLAB_PANIC|SLAB_ACCOUNT,
-			offsetof(struct mm_struct, saved_auxv),
-			sizeof_field(struct mm_struct, saved_auxv),
-			NULL);
 	vm_area_cachep = KMEM_CACHE(vm_area_struct, SLAB_PANIC|SLAB_ACCOUNT);
 	mmap_init();
 	nsproxy_cache_init();
@@ -3000,17 +3032,16 @@
 /*
  * Unshare file descriptor table if it is being shared
  */
-int unshare_fd(unsigned long unshare_flags, unsigned int max_fds,
-	       struct files_struct **new_fdp)
+static int unshare_fd(unsigned long unshare_flags, struct files_struct **new_fdp)
 {
 	struct files_struct *fd = current->files;
-	int error = 0;
 
 	if ((unshare_flags & CLONE_FILES) &&
 	    (fd && atomic_read(&fd->count) > 1)) {
-		*new_fdp = dup_fd(fd, max_fds, &error);
-		if (!*new_fdp)
-			return error;
+		fd = dup_fd(fd, NULL);
+		if (IS_ERR(fd))
+			return PTR_ERR(fd);
+		*new_fdp = fd;
 	}
 
 	return 0;
@@ -3055,6 +3086,12 @@
 	if (unshare_flags & CLONE_NEWNS)
 		unshare_flags |= CLONE_FS;
 
+	if ((unshare_flags & CLONE_NEWUSER) && !unprivileged_userns_clone) {
+		err = -EPERM;
+		if (!capable(CAP_SYS_ADMIN))
+			goto bad_unshare_out;
+	}
+
 	err = check_unshare_flags(unshare_flags);
 	if (err)
 		goto bad_unshare_out;
@@ -3068,7 +3105,7 @@
 	err = unshare_fs(unshare_flags, &new_fs);
 	if (err)
 		goto bad_unshare_out;
-	err = unshare_fd(unshare_flags, NR_OPEN_MAX, &new_fd);
+	err = unshare_fd(unshare_flags, &new_fd);
 	if (err)
 		goto bad_unshare_cleanup_fs;
 	err = unshare_userns(unshare_flags, &new_cred);
@@ -3163,7 +3200,7 @@
 	struct files_struct *old, *copy = NULL;
 	int error;
 
-	error = unshare_fd(CLONE_FILES, NR_OPEN_MAX, &copy);
+	error = unshare_fd(CLONE_FILES, &copy);
 	if (error || !copy)
 		return error;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/futex/Makefile
+++ linux-xilinx-zynqmp-5.15.0/kernel/futex/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-y += core.o
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/futex/core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/futex/core.c
@@ -0,0 +1,4290 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Fast Userspace Mutexes (which I call "Futexes!").
+ *  (C) Rusty Russell, IBM 2002
+ *
+ *  Generalized futexes, futex requeueing, misc fixes by Ingo Molnar
+ *  (C) Copyright 2003 Red Hat Inc, All Rights Reserved
+ *
+ *  Removed page pinning, fix privately mapped COW pages and other cleanups
+ *  (C) Copyright 2003, 2004 Jamie Lokier
+ *
+ *  Robust futex support started by Ingo Molnar
+ *  (C) Copyright 2006 Red Hat Inc, All Rights Reserved
+ *  Thanks to Thomas Gleixner for suggestions, analysis and fixes.
+ *
+ *  PI-futex support started by Ingo Molnar and Thomas Gleixner
+ *  Copyright (C) 2006 Red Hat, Inc., Ingo Molnar <mingo@redhat.com>
+ *  Copyright (C) 2006 Timesys Corp., Thomas Gleixner <tglx@timesys.com>
+ *
+ *  PRIVATE futexes by Eric Dumazet
+ *  Copyright (C) 2007 Eric Dumazet <dada1@cosmosbay.com>
+ *
+ *  Requeue-PI support by Darren Hart <dvhltc@us.ibm.com>
+ *  Copyright (C) IBM Corporation, 2009
+ *  Thanks to Thomas Gleixner for conceptual design and careful reviews.
+ *
+ *  Thanks to Ben LaHaise for yelling "hashed waitqueues" loudly
+ *  enough at me, Linus for the original (flawed) idea, Matthew
+ *  Kirkwood for proof-of-concept implementation.
+ *
+ *  "The futexes are also cursed."
+ *  "But they come in a choice of three flavours!"
+ */
+#include <linux/compat.h>
+#include <linux/jhash.h>
+#include <linux/pagemap.h>
+#include <linux/syscalls.h>
+#include <linux/freezer.h>
+#include <linux/memblock.h>
+#include <linux/fault-inject.h>
+#include <linux/time_namespace.h>
+
+#include <asm/futex.h>
+
+#include "../locking/rtmutex_common.h"
+
+/*
+ * READ this before attempting to hack on futexes!
+ *
+ * Basic futex operation and ordering guarantees
+ * =============================================
+ *
+ * The waiter reads the futex value in user space and calls
+ * futex_wait(). This function computes the hash bucket and acquires
+ * the hash bucket lock. After that it reads the futex user space value
+ * again and verifies that the data has not changed. If it has not changed
+ * it enqueues itself into the hash bucket, releases the hash bucket lock
+ * and schedules.
+ *
+ * The waker side modifies the user space value of the futex and calls
+ * futex_wake(). This function computes the hash bucket and acquires the
+ * hash bucket lock. Then it looks for waiters on that futex in the hash
+ * bucket and wakes them.
+ *
+ * In futex wake up scenarios where no tasks are blocked on a futex, taking
+ * the hb spinlock can be avoided and simply return. In order for this
+ * optimization to work, ordering guarantees must exist so that the waiter
+ * being added to the list is acknowledged when the list is concurrently being
+ * checked by the waker, avoiding scenarios like the following:
+ *
+ * CPU 0                               CPU 1
+ * val = *futex;
+ * sys_futex(WAIT, futex, val);
+ *   futex_wait(futex, val);
+ *   uval = *futex;
+ *                                     *futex = newval;
+ *                                     sys_futex(WAKE, futex);
+ *                                       futex_wake(futex);
+ *                                       if (queue_empty())
+ *                                         return;
+ *   if (uval == val)
+ *      lock(hash_bucket(futex));
+ *      queue();
+ *     unlock(hash_bucket(futex));
+ *     schedule();
+ *
+ * This would cause the waiter on CPU 0 to wait forever because it
+ * missed the transition of the user space value from val to newval
+ * and the waker did not find the waiter in the hash bucket queue.
+ *
+ * The correct serialization ensures that a waiter either observes
+ * the changed user space value before blocking or is woken by a
+ * concurrent waker:
+ *
+ * CPU 0                                 CPU 1
+ * val = *futex;
+ * sys_futex(WAIT, futex, val);
+ *   futex_wait(futex, val);
+ *
+ *   waiters++; (a)
+ *   smp_mb(); (A) <-- paired with -.
+ *                                  |
+ *   lock(hash_bucket(futex));      |
+ *                                  |
+ *   uval = *futex;                 |
+ *                                  |        *futex = newval;
+ *                                  |        sys_futex(WAKE, futex);
+ *                                  |          futex_wake(futex);
+ *                                  |
+ *                                  `--------> smp_mb(); (B)
+ *   if (uval == val)
+ *     queue();
+ *     unlock(hash_bucket(futex));
+ *     schedule();                         if (waiters)
+ *                                           lock(hash_bucket(futex));
+ *   else                                    wake_waiters(futex);
+ *     waiters--; (b)                        unlock(hash_bucket(futex));
+ *
+ * Where (A) orders the waiters increment and the futex value read through
+ * atomic operations (see hb_waiters_inc) and where (B) orders the write
+ * to futex and the waiters read (see hb_waiters_pending()).
+ *
+ * This yields the following case (where X:=waiters, Y:=futex):
+ *
+ *	X = Y = 0
+ *
+ *	w[X]=1		w[Y]=1
+ *	MB		MB
+ *	r[Y]=y		r[X]=x
+ *
+ * Which guarantees that x==0 && y==0 is impossible; which translates back into
+ * the guarantee that we cannot both miss the futex variable change and the
+ * enqueue.
+ *
+ * Note that a new waiter is accounted for in (a) even when it is possible that
+ * the wait call can return error, in which case we backtrack from it in (b).
+ * Refer to the comment in queue_lock().
+ *
+ * Similarly, in order to account for waiters being requeued on another
+ * address we always increment the waiters for the destination bucket before
+ * acquiring the lock. It then decrements them again  after releasing it -
+ * the code that actually moves the futex(es) between hash buckets (requeue_futex)
+ * will do the additional required waiter count housekeeping. This is done for
+ * double_lock_hb() and double_unlock_hb(), respectively.
+ */
+
+#ifdef CONFIG_HAVE_FUTEX_CMPXCHG
+#define futex_cmpxchg_enabled 1
+#else
+static int  __read_mostly futex_cmpxchg_enabled;
+#endif
+
+/*
+ * Futex flags used to encode options to functions and preserve them across
+ * restarts.
+ */
+#ifdef CONFIG_MMU
+# define FLAGS_SHARED		0x01
+#else
+/*
+ * NOMMU does not have per process address space. Let the compiler optimize
+ * code away.
+ */
+# define FLAGS_SHARED		0x00
+#endif
+#define FLAGS_CLOCKRT		0x02
+#define FLAGS_HAS_TIMEOUT	0x04
+
+/*
+ * Priority Inheritance state:
+ */
+struct futex_pi_state {
+	/*
+	 * list of 'owned' pi_state instances - these have to be
+	 * cleaned up in do_exit() if the task exits prematurely:
+	 */
+	struct list_head list;
+
+	/*
+	 * The PI object:
+	 */
+	struct rt_mutex_base pi_mutex;
+
+	struct task_struct *owner;
+	refcount_t refcount;
+
+	union futex_key key;
+} __randomize_layout;
+
+/**
+ * struct futex_q - The hashed futex queue entry, one per waiting task
+ * @list:		priority-sorted list of tasks waiting on this futex
+ * @task:		the task waiting on the futex
+ * @lock_ptr:		the hash bucket lock
+ * @key:		the key the futex is hashed on
+ * @pi_state:		optional priority inheritance state
+ * @rt_waiter:		rt_waiter storage for use with requeue_pi
+ * @requeue_pi_key:	the requeue_pi target futex key
+ * @bitset:		bitset for the optional bitmasked wakeup
+ * @requeue_state:	State field for futex_requeue_pi()
+ * @requeue_wait:	RCU wait for futex_requeue_pi() (RT only)
+ *
+ * We use this hashed waitqueue, instead of a normal wait_queue_entry_t, so
+ * we can wake only the relevant ones (hashed queues may be shared).
+ *
+ * A futex_q has a woken state, just like tasks have TASK_RUNNING.
+ * It is considered woken when plist_node_empty(&q->list) || q->lock_ptr == 0.
+ * The order of wakeup is always to make the first condition true, then
+ * the second.
+ *
+ * PI futexes are typically woken before they are removed from the hash list via
+ * the rt_mutex code. See unqueue_me_pi().
+ */
+struct futex_q {
+	struct plist_node list;
+
+	struct task_struct *task;
+	spinlock_t *lock_ptr;
+	union futex_key key;
+	struct futex_pi_state *pi_state;
+	struct rt_mutex_waiter *rt_waiter;
+	union futex_key *requeue_pi_key;
+	u32 bitset;
+	atomic_t requeue_state;
+#ifdef CONFIG_PREEMPT_RT
+	struct rcuwait requeue_wait;
+#endif
+} __randomize_layout;
+
+/*
+ * On PREEMPT_RT, the hash bucket lock is a 'sleeping' spinlock with an
+ * underlying rtmutex. The task which is about to be requeued could have
+ * just woken up (timeout, signal). After the wake up the task has to
+ * acquire hash bucket lock, which is held by the requeue code.  As a task
+ * can only be blocked on _ONE_ rtmutex at a time, the proxy lock blocking
+ * and the hash bucket lock blocking would collide and corrupt state.
+ *
+ * On !PREEMPT_RT this is not a problem and everything could be serialized
+ * on hash bucket lock, but aside of having the benefit of common code,
+ * this allows to avoid doing the requeue when the task is already on the
+ * way out and taking the hash bucket lock of the original uaddr1 when the
+ * requeue has been completed.
+ *
+ * The following state transitions are valid:
+ *
+ * On the waiter side:
+ *   Q_REQUEUE_PI_NONE		-> Q_REQUEUE_PI_IGNORE
+ *   Q_REQUEUE_PI_IN_PROGRESS	-> Q_REQUEUE_PI_WAIT
+ *
+ * On the requeue side:
+ *   Q_REQUEUE_PI_NONE		-> Q_REQUEUE_PI_INPROGRESS
+ *   Q_REQUEUE_PI_IN_PROGRESS	-> Q_REQUEUE_PI_DONE/LOCKED
+ *   Q_REQUEUE_PI_IN_PROGRESS	-> Q_REQUEUE_PI_NONE (requeue failed)
+ *   Q_REQUEUE_PI_WAIT		-> Q_REQUEUE_PI_DONE/LOCKED
+ *   Q_REQUEUE_PI_WAIT		-> Q_REQUEUE_PI_IGNORE (requeue failed)
+ *
+ * The requeue side ignores a waiter with state Q_REQUEUE_PI_IGNORE as this
+ * signals that the waiter is already on the way out. It also means that
+ * the waiter is still on the 'wait' futex, i.e. uaddr1.
+ *
+ * The waiter side signals early wakeup to the requeue side either through
+ * setting state to Q_REQUEUE_PI_IGNORE or to Q_REQUEUE_PI_WAIT depending
+ * on the current state. In case of Q_REQUEUE_PI_IGNORE it can immediately
+ * proceed to take the hash bucket lock of uaddr1. If it set state to WAIT,
+ * which means the wakeup is interleaving with a requeue in progress it has
+ * to wait for the requeue side to change the state. Either to DONE/LOCKED
+ * or to IGNORE. DONE/LOCKED means the waiter q is now on the uaddr2 futex
+ * and either blocked (DONE) or has acquired it (LOCKED). IGNORE is set by
+ * the requeue side when the requeue attempt failed via deadlock detection
+ * and therefore the waiter q is still on the uaddr1 futex.
+ */
+enum {
+	Q_REQUEUE_PI_NONE		=  0,
+	Q_REQUEUE_PI_IGNORE,
+	Q_REQUEUE_PI_IN_PROGRESS,
+	Q_REQUEUE_PI_WAIT,
+	Q_REQUEUE_PI_DONE,
+	Q_REQUEUE_PI_LOCKED,
+};
+
+static const struct futex_q futex_q_init = {
+	/* list gets initialized in queue_me()*/
+	.key		= FUTEX_KEY_INIT,
+	.bitset		= FUTEX_BITSET_MATCH_ANY,
+	.requeue_state	= ATOMIC_INIT(Q_REQUEUE_PI_NONE),
+};
+
+/*
+ * Hash buckets are shared by all the futex_keys that hash to the same
+ * location.  Each key may have multiple futex_q structures, one for each task
+ * waiting on a futex.
+ */
+struct futex_hash_bucket {
+	atomic_t waiters;
+	spinlock_t lock;
+	struct plist_head chain;
+} ____cacheline_aligned_in_smp;
+
+/*
+ * The base of the bucket array and its size are always used together
+ * (after initialization only in hash_futex()), so ensure that they
+ * reside in the same cacheline.
+ */
+static struct {
+	struct futex_hash_bucket *queues;
+	unsigned long            hashsize;
+} __futex_data __read_mostly __aligned(2*sizeof(long));
+#define futex_queues   (__futex_data.queues)
+#define futex_hashsize (__futex_data.hashsize)
+
+
+/*
+ * Fault injections for futexes.
+ */
+#ifdef CONFIG_FAIL_FUTEX
+
+static struct {
+	struct fault_attr attr;
+
+	bool ignore_private;
+} fail_futex = {
+	.attr = FAULT_ATTR_INITIALIZER,
+	.ignore_private = false,
+};
+
+static int __init setup_fail_futex(char *str)
+{
+	return setup_fault_attr(&fail_futex.attr, str);
+}
+__setup("fail_futex=", setup_fail_futex);
+
+static bool should_fail_futex(bool fshared)
+{
+	if (fail_futex.ignore_private && !fshared)
+		return false;
+
+	return should_fail(&fail_futex.attr, 1);
+}
+
+#ifdef CONFIG_FAULT_INJECTION_DEBUG_FS
+
+static int __init fail_futex_debugfs(void)
+{
+	umode_t mode = S_IFREG | S_IRUSR | S_IWUSR;
+	struct dentry *dir;
+
+	dir = fault_create_debugfs_attr("fail_futex", NULL,
+					&fail_futex.attr);
+	if (IS_ERR(dir))
+		return PTR_ERR(dir);
+
+	debugfs_create_bool("ignore-private", mode, dir,
+			    &fail_futex.ignore_private);
+	return 0;
+}
+
+late_initcall(fail_futex_debugfs);
+
+#endif /* CONFIG_FAULT_INJECTION_DEBUG_FS */
+
+#else
+static inline bool should_fail_futex(bool fshared)
+{
+	return false;
+}
+#endif /* CONFIG_FAIL_FUTEX */
+
+#ifdef CONFIG_COMPAT
+static void compat_exit_robust_list(struct task_struct *curr);
+#endif
+
+/*
+ * Reflects a new waiter being added to the waitqueue.
+ */
+static inline void hb_waiters_inc(struct futex_hash_bucket *hb)
+{
+#ifdef CONFIG_SMP
+	atomic_inc(&hb->waiters);
+	/*
+	 * Full barrier (A), see the ordering comment above.
+	 */
+	smp_mb__after_atomic();
+#endif
+}
+
+/*
+ * Reflects a waiter being removed from the waitqueue by wakeup
+ * paths.
+ */
+static inline void hb_waiters_dec(struct futex_hash_bucket *hb)
+{
+#ifdef CONFIG_SMP
+	atomic_dec(&hb->waiters);
+#endif
+}
+
+static inline int hb_waiters_pending(struct futex_hash_bucket *hb)
+{
+#ifdef CONFIG_SMP
+	/*
+	 * Full barrier (B), see the ordering comment above.
+	 */
+	smp_mb();
+	return atomic_read(&hb->waiters);
+#else
+	return 1;
+#endif
+}
+
+/**
+ * hash_futex - Return the hash bucket in the global hash
+ * @key:	Pointer to the futex key for which the hash is calculated
+ *
+ * We hash on the keys returned from get_futex_key (see below) and return the
+ * corresponding hash bucket in the global hash.
+ */
+static struct futex_hash_bucket *hash_futex(union futex_key *key)
+{
+	u32 hash = jhash2((u32 *)key, offsetof(typeof(*key), both.offset) / 4,
+			  key->both.offset);
+
+	return &futex_queues[hash & (futex_hashsize - 1)];
+}
+
+
+/**
+ * match_futex - Check whether two futex keys are equal
+ * @key1:	Pointer to key1
+ * @key2:	Pointer to key2
+ *
+ * Return 1 if two futex_keys are equal, 0 otherwise.
+ */
+static inline int match_futex(union futex_key *key1, union futex_key *key2)
+{
+	return (key1 && key2
+		&& key1->both.word == key2->both.word
+		&& key1->both.ptr == key2->both.ptr
+		&& key1->both.offset == key2->both.offset);
+}
+
+enum futex_access {
+	FUTEX_READ,
+	FUTEX_WRITE
+};
+
+/**
+ * futex_setup_timer - set up the sleeping hrtimer.
+ * @time:	ptr to the given timeout value
+ * @timeout:	the hrtimer_sleeper structure to be set up
+ * @flags:	futex flags
+ * @range_ns:	optional range in ns
+ *
+ * Return: Initialized hrtimer_sleeper structure or NULL if no timeout
+ *	   value given
+ */
+static inline struct hrtimer_sleeper *
+futex_setup_timer(ktime_t *time, struct hrtimer_sleeper *timeout,
+		  int flags, u64 range_ns)
+{
+	if (!time)
+		return NULL;
+
+	hrtimer_init_sleeper_on_stack(timeout, (flags & FLAGS_CLOCKRT) ?
+				      CLOCK_REALTIME : CLOCK_MONOTONIC,
+				      HRTIMER_MODE_ABS);
+	/*
+	 * If range_ns is 0, calling hrtimer_set_expires_range_ns() is
+	 * effectively the same as calling hrtimer_set_expires().
+	 */
+	hrtimer_set_expires_range_ns(&timeout->timer, *time, range_ns);
+
+	return timeout;
+}
+
+/*
+ * Generate a machine wide unique identifier for this inode.
+ *
+ * This relies on u64 not wrapping in the life-time of the machine; which with
+ * 1ns resolution means almost 585 years.
+ *
+ * This further relies on the fact that a well formed program will not unmap
+ * the file while it has a (shared) futex waiting on it. This mapping will have
+ * a file reference which pins the mount and inode.
+ *
+ * If for some reason an inode gets evicted and read back in again, it will get
+ * a new sequence number and will _NOT_ match, even though it is the exact same
+ * file.
+ *
+ * It is important that match_futex() will never have a false-positive, esp.
+ * for PI futexes that can mess up the state. The above argues that false-negatives
+ * are only possible for malformed programs.
+ */
+static u64 get_inode_sequence_number(struct inode *inode)
+{
+	static atomic64_t i_seq;
+	u64 old;
+
+	/* Does the inode already have a sequence number? */
+	old = atomic64_read(&inode->i_sequence);
+	if (likely(old))
+		return old;
+
+	for (;;) {
+		u64 new = atomic64_add_return(1, &i_seq);
+		if (WARN_ON_ONCE(!new))
+			continue;
+
+		old = atomic64_cmpxchg_relaxed(&inode->i_sequence, 0, new);
+		if (old)
+			return old;
+		return new;
+	}
+}
+
+/**
+ * get_futex_key() - Get parameters which are the keys for a futex
+ * @uaddr:	virtual address of the futex
+ * @fshared:	false for a PROCESS_PRIVATE futex, true for PROCESS_SHARED
+ * @key:	address where result is stored.
+ * @rw:		mapping needs to be read/write (values: FUTEX_READ,
+ *              FUTEX_WRITE)
+ *
+ * Return: a negative error code or 0
+ *
+ * The key words are stored in @key on success.
+ *
+ * For shared mappings (when @fshared), the key is:
+ *
+ *   ( inode->i_sequence, page->index, offset_within_page )
+ *
+ * [ also see get_inode_sequence_number() ]
+ *
+ * For private mappings (or when !@fshared), the key is:
+ *
+ *   ( current->mm, address, 0 )
+ *
+ * This allows (cross process, where applicable) identification of the futex
+ * without keeping the page pinned for the duration of the FUTEX_WAIT.
+ *
+ * lock_page() might sleep, the caller should not hold a spinlock.
+ */
+static int get_futex_key(u32 __user *uaddr, bool fshared, union futex_key *key,
+			 enum futex_access rw)
+{
+	unsigned long address = (unsigned long)uaddr;
+	struct mm_struct *mm = current->mm;
+	struct page *page, *tail;
+	struct address_space *mapping;
+	int err, ro = 0;
+
+	/*
+	 * The futex address must be "naturally" aligned.
+	 */
+	key->both.offset = address % PAGE_SIZE;
+	if (unlikely((address % sizeof(u32)) != 0))
+		return -EINVAL;
+	address -= key->both.offset;
+
+	if (unlikely(!access_ok(uaddr, sizeof(u32))))
+		return -EFAULT;
+
+	if (unlikely(should_fail_futex(fshared)))
+		return -EFAULT;
+
+	/*
+	 * PROCESS_PRIVATE futexes are fast.
+	 * As the mm cannot disappear under us and the 'key' only needs
+	 * virtual address, we dont even have to find the underlying vma.
+	 * Note : We do have to check 'uaddr' is a valid user address,
+	 *        but access_ok() should be faster than find_vma()
+	 */
+	if (!fshared) {
+		/*
+		 * On no-MMU, shared futexes are treated as private, therefore
+		 * we must not include the current process in the key. Since
+		 * there is only one address space, the address is a unique key
+		 * on its own.
+		 */
+		if (IS_ENABLED(CONFIG_MMU))
+			key->private.mm = mm;
+		else
+			key->private.mm = NULL;
+
+		key->private.address = address;
+		return 0;
+	}
+
+again:
+	/* Ignore any VERIFY_READ mapping (futex common case) */
+	if (unlikely(should_fail_futex(true)))
+		return -EFAULT;
+
+	err = get_user_pages_fast(address, 1, FOLL_WRITE, &page);
+	/*
+	 * If write access is not required (eg. FUTEX_WAIT), try
+	 * and get read-only access.
+	 */
+	if (err == -EFAULT && rw == FUTEX_READ) {
+		err = get_user_pages_fast(address, 1, 0, &page);
+		ro = 1;
+	}
+	if (err < 0)
+		return err;
+	else
+		err = 0;
+
+	/*
+	 * The treatment of mapping from this point on is critical. The page
+	 * lock protects many things but in this context the page lock
+	 * stabilizes mapping, prevents inode freeing in the shared
+	 * file-backed region case and guards against movement to swap cache.
+	 *
+	 * Strictly speaking the page lock is not needed in all cases being
+	 * considered here and page lock forces unnecessarily serialization
+	 * From this point on, mapping will be re-verified if necessary and
+	 * page lock will be acquired only if it is unavoidable
+	 *
+	 * Mapping checks require the head page for any compound page so the
+	 * head page and mapping is looked up now. For anonymous pages, it
+	 * does not matter if the page splits in the future as the key is
+	 * based on the address. For filesystem-backed pages, the tail is
+	 * required as the index of the page determines the key. For
+	 * base pages, there is no tail page and tail == page.
+	 */
+	tail = page;
+	page = compound_head(page);
+	mapping = READ_ONCE(page->mapping);
+
+	/*
+	 * If page->mapping is NULL, then it cannot be a PageAnon
+	 * page; but it might be the ZERO_PAGE or in the gate area or
+	 * in a special mapping (all cases which we are happy to fail);
+	 * or it may have been a good file page when get_user_pages_fast
+	 * found it, but truncated or holepunched or subjected to
+	 * invalidate_complete_page2 before we got the page lock (also
+	 * cases which we are happy to fail).  And we hold a reference,
+	 * so refcount care in invalidate_complete_page's remove_mapping
+	 * prevents drop_caches from setting mapping to NULL beneath us.
+	 *
+	 * The case we do have to guard against is when memory pressure made
+	 * shmem_writepage move it from filecache to swapcache beneath us:
+	 * an unlikely race, but we do need to retry for page->mapping.
+	 */
+	if (unlikely(!mapping)) {
+		int shmem_swizzled;
+
+		/*
+		 * Page lock is required to identify which special case above
+		 * applies. If this is really a shmem page then the page lock
+		 * will prevent unexpected transitions.
+		 */
+		lock_page(page);
+		shmem_swizzled = PageSwapCache(page) || page->mapping;
+		unlock_page(page);
+		put_page(page);
+
+		if (shmem_swizzled)
+			goto again;
+
+		return -EFAULT;
+	}
+
+	/*
+	 * Private mappings are handled in a simple way.
+	 *
+	 * If the futex key is stored on an anonymous page, then the associated
+	 * object is the mm which is implicitly pinned by the calling process.
+	 *
+	 * NOTE: When userspace waits on a MAP_SHARED mapping, even if
+	 * it's a read-only handle, it's expected that futexes attach to
+	 * the object not the particular process.
+	 */
+	if (PageAnon(page)) {
+		/*
+		 * A RO anonymous page will never change and thus doesn't make
+		 * sense for futex operations.
+		 */
+		if (unlikely(should_fail_futex(true)) || ro) {
+			err = -EFAULT;
+			goto out;
+		}
+
+		key->both.offset |= FUT_OFF_MMSHARED; /* ref taken on mm */
+		key->private.mm = mm;
+		key->private.address = address;
+
+	} else {
+		struct inode *inode;
+
+		/*
+		 * The associated futex object in this case is the inode and
+		 * the page->mapping must be traversed. Ordinarily this should
+		 * be stabilised under page lock but it's not strictly
+		 * necessary in this case as we just want to pin the inode, not
+		 * update the radix tree or anything like that.
+		 *
+		 * The RCU read lock is taken as the inode is finally freed
+		 * under RCU. If the mapping still matches expectations then the
+		 * mapping->host can be safely accessed as being a valid inode.
+		 */
+		rcu_read_lock();
+
+		if (READ_ONCE(page->mapping) != mapping) {
+			rcu_read_unlock();
+			put_page(page);
+
+			goto again;
+		}
+
+		inode = READ_ONCE(mapping->host);
+		if (!inode) {
+			rcu_read_unlock();
+			put_page(page);
+
+			goto again;
+		}
+
+		key->both.offset |= FUT_OFF_INODE; /* inode-based key */
+		key->shared.i_seq = get_inode_sequence_number(inode);
+		key->shared.pgoff = page_to_pgoff(tail);
+		rcu_read_unlock();
+	}
+
+out:
+	put_page(page);
+	return err;
+}
+
+/**
+ * fault_in_user_writeable() - Fault in user address and verify RW access
+ * @uaddr:	pointer to faulting user space address
+ *
+ * Slow path to fixup the fault we just took in the atomic write
+ * access to @uaddr.
+ *
+ * We have no generic implementation of a non-destructive write to the
+ * user address. We know that we faulted in the atomic pagefault
+ * disabled section so we can as well avoid the #PF overhead by
+ * calling get_user_pages() right away.
+ */
+static int fault_in_user_writeable(u32 __user *uaddr)
+{
+	struct mm_struct *mm = current->mm;
+	int ret;
+
+	mmap_read_lock(mm);
+	ret = fixup_user_fault(mm, (unsigned long)uaddr,
+			       FAULT_FLAG_WRITE, NULL);
+	mmap_read_unlock(mm);
+
+	return ret < 0 ? ret : 0;
+}
+
+/**
+ * futex_top_waiter() - Return the highest priority waiter on a futex
+ * @hb:		the hash bucket the futex_q's reside in
+ * @key:	the futex key (to distinguish it from other futex futex_q's)
+ *
+ * Must be called with the hb lock held.
+ */
+static struct futex_q *futex_top_waiter(struct futex_hash_bucket *hb,
+					union futex_key *key)
+{
+	struct futex_q *this;
+
+	plist_for_each_entry(this, &hb->chain, list) {
+		if (match_futex(&this->key, key))
+			return this;
+	}
+	return NULL;
+}
+
+static int cmpxchg_futex_value_locked(u32 *curval, u32 __user *uaddr,
+				      u32 uval, u32 newval)
+{
+	int ret;
+
+	pagefault_disable();
+	ret = futex_atomic_cmpxchg_inatomic(curval, uaddr, uval, newval);
+	pagefault_enable();
+
+	return ret;
+}
+
+static int get_futex_value_locked(u32 *dest, u32 __user *from)
+{
+	int ret;
+
+	pagefault_disable();
+	ret = __get_user(*dest, from);
+	pagefault_enable();
+
+	return ret ? -EFAULT : 0;
+}
+
+
+/*
+ * PI code:
+ */
+static int refill_pi_state_cache(void)
+{
+	struct futex_pi_state *pi_state;
+
+	if (likely(current->pi_state_cache))
+		return 0;
+
+	pi_state = kzalloc(sizeof(*pi_state), GFP_KERNEL);
+
+	if (!pi_state)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&pi_state->list);
+	/* pi_mutex gets initialized later */
+	pi_state->owner = NULL;
+	refcount_set(&pi_state->refcount, 1);
+	pi_state->key = FUTEX_KEY_INIT;
+
+	current->pi_state_cache = pi_state;
+
+	return 0;
+}
+
+static struct futex_pi_state *alloc_pi_state(void)
+{
+	struct futex_pi_state *pi_state = current->pi_state_cache;
+
+	WARN_ON(!pi_state);
+	current->pi_state_cache = NULL;
+
+	return pi_state;
+}
+
+static void pi_state_update_owner(struct futex_pi_state *pi_state,
+				  struct task_struct *new_owner)
+{
+	struct task_struct *old_owner = pi_state->owner;
+
+	lockdep_assert_held(&pi_state->pi_mutex.wait_lock);
+
+	if (old_owner) {
+		raw_spin_lock(&old_owner->pi_lock);
+		WARN_ON(list_empty(&pi_state->list));
+		list_del_init(&pi_state->list);
+		raw_spin_unlock(&old_owner->pi_lock);
+	}
+
+	if (new_owner) {
+		raw_spin_lock(&new_owner->pi_lock);
+		WARN_ON(!list_empty(&pi_state->list));
+		list_add(&pi_state->list, &new_owner->pi_state_list);
+		pi_state->owner = new_owner;
+		raw_spin_unlock(&new_owner->pi_lock);
+	}
+}
+
+static void get_pi_state(struct futex_pi_state *pi_state)
+{
+	WARN_ON_ONCE(!refcount_inc_not_zero(&pi_state->refcount));
+}
+
+/*
+ * Drops a reference to the pi_state object and frees or caches it
+ * when the last reference is gone.
+ */
+static void put_pi_state(struct futex_pi_state *pi_state)
+{
+	if (!pi_state)
+		return;
+
+	if (!refcount_dec_and_test(&pi_state->refcount))
+		return;
+
+	/*
+	 * If pi_state->owner is NULL, the owner is most probably dying
+	 * and has cleaned up the pi_state already
+	 */
+	if (pi_state->owner) {
+		unsigned long flags;
+
+		raw_spin_lock_irqsave(&pi_state->pi_mutex.wait_lock, flags);
+		pi_state_update_owner(pi_state, NULL);
+		rt_mutex_proxy_unlock(&pi_state->pi_mutex);
+		raw_spin_unlock_irqrestore(&pi_state->pi_mutex.wait_lock, flags);
+	}
+
+	if (current->pi_state_cache) {
+		kfree(pi_state);
+	} else {
+		/*
+		 * pi_state->list is already empty.
+		 * clear pi_state->owner.
+		 * refcount is at 0 - put it back to 1.
+		 */
+		pi_state->owner = NULL;
+		refcount_set(&pi_state->refcount, 1);
+		current->pi_state_cache = pi_state;
+	}
+}
+
+#ifdef CONFIG_FUTEX_PI
+
+/*
+ * This task is holding PI mutexes at exit time => bad.
+ * Kernel cleans up PI-state, but userspace is likely hosed.
+ * (Robust-futex cleanup is separate and might save the day for userspace.)
+ */
+static void exit_pi_state_list(struct task_struct *curr)
+{
+	struct list_head *next, *head = &curr->pi_state_list;
+	struct futex_pi_state *pi_state;
+	struct futex_hash_bucket *hb;
+	union futex_key key = FUTEX_KEY_INIT;
+
+	if (!futex_cmpxchg_enabled)
+		return;
+	/*
+	 * We are a ZOMBIE and nobody can enqueue itself on
+	 * pi_state_list anymore, but we have to be careful
+	 * versus waiters unqueueing themselves:
+	 */
+	raw_spin_lock_irq(&curr->pi_lock);
+	while (!list_empty(head)) {
+		next = head->next;
+		pi_state = list_entry(next, struct futex_pi_state, list);
+		key = pi_state->key;
+		hb = hash_futex(&key);
+
+		/*
+		 * We can race against put_pi_state() removing itself from the
+		 * list (a waiter going away). put_pi_state() will first
+		 * decrement the reference count and then modify the list, so
+		 * its possible to see the list entry but fail this reference
+		 * acquire.
+		 *
+		 * In that case; drop the locks to let put_pi_state() make
+		 * progress and retry the loop.
+		 */
+		if (!refcount_inc_not_zero(&pi_state->refcount)) {
+			raw_spin_unlock_irq(&curr->pi_lock);
+			cpu_relax();
+			raw_spin_lock_irq(&curr->pi_lock);
+			continue;
+		}
+		raw_spin_unlock_irq(&curr->pi_lock);
+
+		spin_lock(&hb->lock);
+		raw_spin_lock_irq(&pi_state->pi_mutex.wait_lock);
+		raw_spin_lock(&curr->pi_lock);
+		/*
+		 * We dropped the pi-lock, so re-check whether this
+		 * task still owns the PI-state:
+		 */
+		if (head->next != next) {
+			/* retain curr->pi_lock for the loop invariant */
+			raw_spin_unlock(&pi_state->pi_mutex.wait_lock);
+			spin_unlock(&hb->lock);
+			put_pi_state(pi_state);
+			continue;
+		}
+
+		WARN_ON(pi_state->owner != curr);
+		WARN_ON(list_empty(&pi_state->list));
+		list_del_init(&pi_state->list);
+		pi_state->owner = NULL;
+
+		raw_spin_unlock(&curr->pi_lock);
+		raw_spin_unlock_irq(&pi_state->pi_mutex.wait_lock);
+		spin_unlock(&hb->lock);
+
+		rt_mutex_futex_unlock(&pi_state->pi_mutex);
+		put_pi_state(pi_state);
+
+		raw_spin_lock_irq(&curr->pi_lock);
+	}
+	raw_spin_unlock_irq(&curr->pi_lock);
+}
+#else
+static inline void exit_pi_state_list(struct task_struct *curr) { }
+#endif
+
+/*
+ * We need to check the following states:
+ *
+ *      Waiter | pi_state | pi->owner | uTID      | uODIED | ?
+ *
+ * [1]  NULL   | ---      | ---       | 0         | 0/1    | Valid
+ * [2]  NULL   | ---      | ---       | >0        | 0/1    | Valid
+ *
+ * [3]  Found  | NULL     | --        | Any       | 0/1    | Invalid
+ *
+ * [4]  Found  | Found    | NULL      | 0         | 1      | Valid
+ * [5]  Found  | Found    | NULL      | >0        | 1      | Invalid
+ *
+ * [6]  Found  | Found    | task      | 0         | 1      | Valid
+ *
+ * [7]  Found  | Found    | NULL      | Any       | 0      | Invalid
+ *
+ * [8]  Found  | Found    | task      | ==taskTID | 0/1    | Valid
+ * [9]  Found  | Found    | task      | 0         | 0      | Invalid
+ * [10] Found  | Found    | task      | !=taskTID | 0/1    | Invalid
+ *
+ * [1]	Indicates that the kernel can acquire the futex atomically. We
+ *	came here due to a stale FUTEX_WAITERS/FUTEX_OWNER_DIED bit.
+ *
+ * [2]	Valid, if TID does not belong to a kernel thread. If no matching
+ *      thread is found then it indicates that the owner TID has died.
+ *
+ * [3]	Invalid. The waiter is queued on a non PI futex
+ *
+ * [4]	Valid state after exit_robust_list(), which sets the user space
+ *	value to FUTEX_WAITERS | FUTEX_OWNER_DIED.
+ *
+ * [5]	The user space value got manipulated between exit_robust_list()
+ *	and exit_pi_state_list()
+ *
+ * [6]	Valid state after exit_pi_state_list() which sets the new owner in
+ *	the pi_state but cannot access the user space value.
+ *
+ * [7]	pi_state->owner can only be NULL when the OWNER_DIED bit is set.
+ *
+ * [8]	Owner and user space value match
+ *
+ * [9]	There is no transient state which sets the user space TID to 0
+ *	except exit_robust_list(), but this is indicated by the
+ *	FUTEX_OWNER_DIED bit. See [4]
+ *
+ * [10] There is no transient state which leaves owner and user space
+ *	TID out of sync. Except one error case where the kernel is denied
+ *	write access to the user address, see fixup_pi_state_owner().
+ *
+ *
+ * Serialization and lifetime rules:
+ *
+ * hb->lock:
+ *
+ *	hb -> futex_q, relation
+ *	futex_q -> pi_state, relation
+ *
+ *	(cannot be raw because hb can contain arbitrary amount
+ *	 of futex_q's)
+ *
+ * pi_mutex->wait_lock:
+ *
+ *	{uval, pi_state}
+ *
+ *	(and pi_mutex 'obviously')
+ *
+ * p->pi_lock:
+ *
+ *	p->pi_state_list -> pi_state->list, relation
+ *	pi_mutex->owner -> pi_state->owner, relation
+ *
+ * pi_state->refcount:
+ *
+ *	pi_state lifetime
+ *
+ *
+ * Lock order:
+ *
+ *   hb->lock
+ *     pi_mutex->wait_lock
+ *       p->pi_lock
+ *
+ */
+
+/*
+ * Validate that the existing waiter has a pi_state and sanity check
+ * the pi_state against the user space value. If correct, attach to
+ * it.
+ */
+static int attach_to_pi_state(u32 __user *uaddr, u32 uval,
+			      struct futex_pi_state *pi_state,
+			      struct futex_pi_state **ps)
+{
+	pid_t pid = uval & FUTEX_TID_MASK;
+	u32 uval2;
+	int ret;
+
+	/*
+	 * Userspace might have messed up non-PI and PI futexes [3]
+	 */
+	if (unlikely(!pi_state))
+		return -EINVAL;
+
+	/*
+	 * We get here with hb->lock held, and having found a
+	 * futex_top_waiter(). This means that futex_lock_pi() of said futex_q
+	 * has dropped the hb->lock in between queue_me() and unqueue_me_pi(),
+	 * which in turn means that futex_lock_pi() still has a reference on
+	 * our pi_state.
+	 *
+	 * The waiter holding a reference on @pi_state also protects against
+	 * the unlocked put_pi_state() in futex_unlock_pi(), futex_lock_pi()
+	 * and futex_wait_requeue_pi() as it cannot go to 0 and consequently
+	 * free pi_state before we can take a reference ourselves.
+	 */
+	WARN_ON(!refcount_read(&pi_state->refcount));
+
+	/*
+	 * Now that we have a pi_state, we can acquire wait_lock
+	 * and do the state validation.
+	 */
+	raw_spin_lock_irq(&pi_state->pi_mutex.wait_lock);
+
+	/*
+	 * Since {uval, pi_state} is serialized by wait_lock, and our current
+	 * uval was read without holding it, it can have changed. Verify it
+	 * still is what we expect it to be, otherwise retry the entire
+	 * operation.
+	 */
+	if (get_futex_value_locked(&uval2, uaddr))
+		goto out_efault;
+
+	if (uval != uval2)
+		goto out_eagain;
+
+	/*
+	 * Handle the owner died case:
+	 */
+	if (uval & FUTEX_OWNER_DIED) {
+		/*
+		 * exit_pi_state_list sets owner to NULL and wakes the
+		 * topmost waiter. The task which acquires the
+		 * pi_state->rt_mutex will fixup owner.
+		 */
+		if (!pi_state->owner) {
+			/*
+			 * No pi state owner, but the user space TID
+			 * is not 0. Inconsistent state. [5]
+			 */
+			if (pid)
+				goto out_einval;
+			/*
+			 * Take a ref on the state and return success. [4]
+			 */
+			goto out_attach;
+		}
+
+		/*
+		 * If TID is 0, then either the dying owner has not
+		 * yet executed exit_pi_state_list() or some waiter
+		 * acquired the rtmutex in the pi state, but did not
+		 * yet fixup the TID in user space.
+		 *
+		 * Take a ref on the state and return success. [6]
+		 */
+		if (!pid)
+			goto out_attach;
+	} else {
+		/*
+		 * If the owner died bit is not set, then the pi_state
+		 * must have an owner. [7]
+		 */
+		if (!pi_state->owner)
+			goto out_einval;
+	}
+
+	/*
+	 * Bail out if user space manipulated the futex value. If pi
+	 * state exists then the owner TID must be the same as the
+	 * user space TID. [9/10]
+	 */
+	if (pid != task_pid_vnr(pi_state->owner))
+		goto out_einval;
+
+out_attach:
+	get_pi_state(pi_state);
+	raw_spin_unlock_irq(&pi_state->pi_mutex.wait_lock);
+	*ps = pi_state;
+	return 0;
+
+out_einval:
+	ret = -EINVAL;
+	goto out_error;
+
+out_eagain:
+	ret = -EAGAIN;
+	goto out_error;
+
+out_efault:
+	ret = -EFAULT;
+	goto out_error;
+
+out_error:
+	raw_spin_unlock_irq(&pi_state->pi_mutex.wait_lock);
+	return ret;
+}
+
+/**
+ * wait_for_owner_exiting - Block until the owner has exited
+ * @ret: owner's current futex lock status
+ * @exiting:	Pointer to the exiting task
+ *
+ * Caller must hold a refcount on @exiting.
+ */
+static void wait_for_owner_exiting(int ret, struct task_struct *exiting)
+{
+	if (ret != -EBUSY) {
+		WARN_ON_ONCE(exiting);
+		return;
+	}
+
+	if (WARN_ON_ONCE(ret == -EBUSY && !exiting))
+		return;
+
+	mutex_lock(&exiting->futex_exit_mutex);
+	/*
+	 * No point in doing state checking here. If the waiter got here
+	 * while the task was in exec()->exec_futex_release() then it can
+	 * have any FUTEX_STATE_* value when the waiter has acquired the
+	 * mutex. OK, if running, EXITING or DEAD if it reached exit()
+	 * already. Highly unlikely and not a problem. Just one more round
+	 * through the futex maze.
+	 */
+	mutex_unlock(&exiting->futex_exit_mutex);
+
+	put_task_struct(exiting);
+}
+
+static int handle_exit_race(u32 __user *uaddr, u32 uval,
+			    struct task_struct *tsk)
+{
+	u32 uval2;
+
+	/*
+	 * If the futex exit state is not yet FUTEX_STATE_DEAD, tell the
+	 * caller that the alleged owner is busy.
+	 */
+	if (tsk && tsk->futex_state != FUTEX_STATE_DEAD)
+		return -EBUSY;
+
+	/*
+	 * Reread the user space value to handle the following situation:
+	 *
+	 * CPU0				CPU1
+	 *
+	 * sys_exit()			sys_futex()
+	 *  do_exit()			 futex_lock_pi()
+	 *                                futex_lock_pi_atomic()
+	 *   exit_signals(tsk)		    No waiters:
+	 *    tsk->flags |= PF_EXITING;	    *uaddr == 0x00000PID
+	 *  mm_release(tsk)		    Set waiter bit
+	 *   exit_robust_list(tsk) {	    *uaddr = 0x80000PID;
+	 *      Set owner died		    attach_to_pi_owner() {
+	 *    *uaddr = 0xC0000000;	     tsk = get_task(PID);
+	 *   }				     if (!tsk->flags & PF_EXITING) {
+	 *  ...				       attach();
+	 *  tsk->futex_state =               } else {
+	 *	FUTEX_STATE_DEAD;              if (tsk->futex_state !=
+	 *					  FUTEX_STATE_DEAD)
+	 *				         return -EAGAIN;
+	 *				       return -ESRCH; <--- FAIL
+	 *				     }
+	 *
+	 * Returning ESRCH unconditionally is wrong here because the
+	 * user space value has been changed by the exiting task.
+	 *
+	 * The same logic applies to the case where the exiting task is
+	 * already gone.
+	 */
+	if (get_futex_value_locked(&uval2, uaddr))
+		return -EFAULT;
+
+	/* If the user space value has changed, try again. */
+	if (uval2 != uval)
+		return -EAGAIN;
+
+	/*
+	 * The exiting task did not have a robust list, the robust list was
+	 * corrupted or the user space value in *uaddr is simply bogus.
+	 * Give up and tell user space.
+	 */
+	return -ESRCH;
+}
+
+static void __attach_to_pi_owner(struct task_struct *p, union futex_key *key,
+				 struct futex_pi_state **ps)
+{
+	/*
+	 * No existing pi state. First waiter. [2]
+	 *
+	 * This creates pi_state, we have hb->lock held, this means nothing can
+	 * observe this state, wait_lock is irrelevant.
+	 */
+	struct futex_pi_state *pi_state = alloc_pi_state();
+
+	/*
+	 * Initialize the pi_mutex in locked state and make @p
+	 * the owner of it:
+	 */
+	rt_mutex_init_proxy_locked(&pi_state->pi_mutex, p);
+
+	/* Store the key for possible exit cleanups: */
+	pi_state->key = *key;
+
+	WARN_ON(!list_empty(&pi_state->list));
+	list_add(&pi_state->list, &p->pi_state_list);
+	/*
+	 * Assignment without holding pi_state->pi_mutex.wait_lock is safe
+	 * because there is no concurrency as the object is not published yet.
+	 */
+	pi_state->owner = p;
+
+	*ps = pi_state;
+}
+/*
+ * Lookup the task for the TID provided from user space and attach to
+ * it after doing proper sanity checks.
+ */
+static int attach_to_pi_owner(u32 __user *uaddr, u32 uval, union futex_key *key,
+			      struct futex_pi_state **ps,
+			      struct task_struct **exiting)
+{
+	pid_t pid = uval & FUTEX_TID_MASK;
+	struct task_struct *p;
+
+	/*
+	 * We are the first waiter - try to look up the real owner and attach
+	 * the new pi_state to it, but bail out when TID = 0 [1]
+	 *
+	 * The !pid check is paranoid. None of the call sites should end up
+	 * with pid == 0, but better safe than sorry. Let the caller retry
+	 */
+	if (!pid)
+		return -EAGAIN;
+	p = find_get_task_by_vpid(pid);
+	if (!p)
+		return handle_exit_race(uaddr, uval, NULL);
+
+	if (unlikely(p->flags & PF_KTHREAD)) {
+		put_task_struct(p);
+		return -EPERM;
+	}
+
+	/*
+	 * We need to look at the task state to figure out, whether the
+	 * task is exiting. To protect against the change of the task state
+	 * in futex_exit_release(), we do this protected by p->pi_lock:
+	 */
+	raw_spin_lock_irq(&p->pi_lock);
+	if (unlikely(p->futex_state != FUTEX_STATE_OK)) {
+		/*
+		 * The task is on the way out. When the futex state is
+		 * FUTEX_STATE_DEAD, we know that the task has finished
+		 * the cleanup:
+		 */
+		int ret = handle_exit_race(uaddr, uval, p);
+
+		raw_spin_unlock_irq(&p->pi_lock);
+		/*
+		 * If the owner task is between FUTEX_STATE_EXITING and
+		 * FUTEX_STATE_DEAD then store the task pointer and keep
+		 * the reference on the task struct. The calling code will
+		 * drop all locks, wait for the task to reach
+		 * FUTEX_STATE_DEAD and then drop the refcount. This is
+		 * required to prevent a live lock when the current task
+		 * preempted the exiting task between the two states.
+		 */
+		if (ret == -EBUSY)
+			*exiting = p;
+		else
+			put_task_struct(p);
+		return ret;
+	}
+
+	__attach_to_pi_owner(p, key, ps);
+	raw_spin_unlock_irq(&p->pi_lock);
+
+	put_task_struct(p);
+
+	return 0;
+}
+
+static int lock_pi_update_atomic(u32 __user *uaddr, u32 uval, u32 newval)
+{
+	int err;
+	u32 curval;
+
+	if (unlikely(should_fail_futex(true)))
+		return -EFAULT;
+
+	err = cmpxchg_futex_value_locked(&curval, uaddr, uval, newval);
+	if (unlikely(err))
+		return err;
+
+	/* If user space value changed, let the caller retry */
+	return curval != uval ? -EAGAIN : 0;
+}
+
+/**
+ * futex_lock_pi_atomic() - Atomic work required to acquire a pi aware futex
+ * @uaddr:		the pi futex user address
+ * @hb:			the pi futex hash bucket
+ * @key:		the futex key associated with uaddr and hb
+ * @ps:			the pi_state pointer where we store the result of the
+ *			lookup
+ * @task:		the task to perform the atomic lock work for.  This will
+ *			be "current" except in the case of requeue pi.
+ * @exiting:		Pointer to store the task pointer of the owner task
+ *			which is in the middle of exiting
+ * @set_waiters:	force setting the FUTEX_WAITERS bit (1) or not (0)
+ *
+ * Return:
+ *  -  0 - ready to wait;
+ *  -  1 - acquired the lock;
+ *  - <0 - error
+ *
+ * The hb->lock must be held by the caller.
+ *
+ * @exiting is only set when the return value is -EBUSY. If so, this holds
+ * a refcount on the exiting task on return and the caller needs to drop it
+ * after waiting for the exit to complete.
+ */
+static int futex_lock_pi_atomic(u32 __user *uaddr, struct futex_hash_bucket *hb,
+				union futex_key *key,
+				struct futex_pi_state **ps,
+				struct task_struct *task,
+				struct task_struct **exiting,
+				int set_waiters)
+{
+	u32 uval, newval, vpid = task_pid_vnr(task);
+	struct futex_q *top_waiter;
+	int ret;
+
+	/*
+	 * Read the user space value first so we can validate a few
+	 * things before proceeding further.
+	 */
+	if (get_futex_value_locked(&uval, uaddr))
+		return -EFAULT;
+
+	if (unlikely(should_fail_futex(true)))
+		return -EFAULT;
+
+	/*
+	 * Detect deadlocks.
+	 */
+	if ((unlikely((uval & FUTEX_TID_MASK) == vpid)))
+		return -EDEADLK;
+
+	if ((unlikely(should_fail_futex(true))))
+		return -EDEADLK;
+
+	/*
+	 * Lookup existing state first. If it exists, try to attach to
+	 * its pi_state.
+	 */
+	top_waiter = futex_top_waiter(hb, key);
+	if (top_waiter)
+		return attach_to_pi_state(uaddr, uval, top_waiter->pi_state, ps);
+
+	/*
+	 * No waiter and user TID is 0. We are here because the
+	 * waiters or the owner died bit is set or called from
+	 * requeue_cmp_pi or for whatever reason something took the
+	 * syscall.
+	 */
+	if (!(uval & FUTEX_TID_MASK)) {
+		/*
+		 * We take over the futex. No other waiters and the user space
+		 * TID is 0. We preserve the owner died bit.
+		 */
+		newval = uval & FUTEX_OWNER_DIED;
+		newval |= vpid;
+
+		/* The futex requeue_pi code can enforce the waiters bit */
+		if (set_waiters)
+			newval |= FUTEX_WAITERS;
+
+		ret = lock_pi_update_atomic(uaddr, uval, newval);
+		if (ret)
+			return ret;
+
+		/*
+		 * If the waiter bit was requested the caller also needs PI
+		 * state attached to the new owner of the user space futex.
+		 *
+		 * @task is guaranteed to be alive and it cannot be exiting
+		 * because it is either sleeping or waiting in
+		 * futex_requeue_pi_wakeup_sync().
+		 *
+		 * No need to do the full attach_to_pi_owner() exercise
+		 * because @task is known and valid.
+		 */
+		if (set_waiters) {
+			raw_spin_lock_irq(&task->pi_lock);
+			__attach_to_pi_owner(task, key, ps);
+			raw_spin_unlock_irq(&task->pi_lock);
+		}
+		return 1;
+	}
+
+	/*
+	 * First waiter. Set the waiters bit before attaching ourself to
+	 * the owner. If owner tries to unlock, it will be forced into
+	 * the kernel and blocked on hb->lock.
+	 */
+	newval = uval | FUTEX_WAITERS;
+	ret = lock_pi_update_atomic(uaddr, uval, newval);
+	if (ret)
+		return ret;
+	/*
+	 * If the update of the user space value succeeded, we try to
+	 * attach to the owner. If that fails, no harm done, we only
+	 * set the FUTEX_WAITERS bit in the user space variable.
+	 */
+	return attach_to_pi_owner(uaddr, newval, key, ps, exiting);
+}
+
+/**
+ * __unqueue_futex() - Remove the futex_q from its futex_hash_bucket
+ * @q:	The futex_q to unqueue
+ *
+ * The q->lock_ptr must not be NULL and must be held by the caller.
+ */
+static void __unqueue_futex(struct futex_q *q)
+{
+	struct futex_hash_bucket *hb;
+
+	if (WARN_ON_SMP(!q->lock_ptr) || WARN_ON(plist_node_empty(&q->list)))
+		return;
+	lockdep_assert_held(q->lock_ptr);
+
+	hb = container_of(q->lock_ptr, struct futex_hash_bucket, lock);
+	plist_del(&q->list, &hb->chain);
+	hb_waiters_dec(hb);
+}
+
+/*
+ * The hash bucket lock must be held when this is called.
+ * Afterwards, the futex_q must not be accessed. Callers
+ * must ensure to later call wake_up_q() for the actual
+ * wakeups to occur.
+ */
+static void mark_wake_futex(struct wake_q_head *wake_q, struct futex_q *q)
+{
+	struct task_struct *p = q->task;
+
+	if (WARN(q->pi_state || q->rt_waiter, "refusing to wake PI futex\n"))
+		return;
+
+	get_task_struct(p);
+	__unqueue_futex(q);
+	/*
+	 * The waiting task can free the futex_q as soon as q->lock_ptr = NULL
+	 * is written, without taking any locks. This is possible in the event
+	 * of a spurious wakeup, for example. A memory barrier is required here
+	 * to prevent the following store to lock_ptr from getting ahead of the
+	 * plist_del in __unqueue_futex().
+	 */
+	smp_store_release(&q->lock_ptr, NULL);
+
+	/*
+	 * Queue the task for later wakeup for after we've released
+	 * the hb->lock.
+	 */
+	wake_q_add_safe(wake_q, p);
+}
+
+/*
+ * Caller must hold a reference on @pi_state.
+ */
+static int wake_futex_pi(u32 __user *uaddr, u32 uval, struct futex_pi_state *pi_state)
+{
+	struct rt_mutex_waiter *top_waiter;
+	struct task_struct *new_owner;
+	bool postunlock = false;
+	DEFINE_RT_WAKE_Q(wqh);
+	u32 curval, newval;
+	int ret = 0;
+
+	top_waiter = rt_mutex_top_waiter(&pi_state->pi_mutex);
+	if (WARN_ON_ONCE(!top_waiter)) {
+		/*
+		 * As per the comment in futex_unlock_pi() this should not happen.
+		 *
+		 * When this happens, give up our locks and try again, giving
+		 * the futex_lock_pi() instance time to complete, either by
+		 * waiting on the rtmutex or removing itself from the futex
+		 * queue.
+		 */
+		ret = -EAGAIN;
+		goto out_unlock;
+	}
+
+	new_owner = top_waiter->task;
+
+	/*
+	 * We pass it to the next owner. The WAITERS bit is always kept
+	 * enabled while there is PI state around. We cleanup the owner
+	 * died bit, because we are the owner.
+	 */
+	newval = FUTEX_WAITERS | task_pid_vnr(new_owner);
+
+	if (unlikely(should_fail_futex(true))) {
+		ret = -EFAULT;
+		goto out_unlock;
+	}
+
+	ret = cmpxchg_futex_value_locked(&curval, uaddr, uval, newval);
+	if (!ret && (curval != uval)) {
+		/*
+		 * If a unconditional UNLOCK_PI operation (user space did not
+		 * try the TID->0 transition) raced with a waiter setting the
+		 * FUTEX_WAITERS flag between get_user() and locking the hash
+		 * bucket lock, retry the operation.
+		 */
+		if ((FUTEX_TID_MASK & curval) == uval)
+			ret = -EAGAIN;
+		else
+			ret = -EINVAL;
+	}
+
+	if (!ret) {
+		/*
+		 * This is a point of no return; once we modified the uval
+		 * there is no going back and subsequent operations must
+		 * not fail.
+		 */
+		pi_state_update_owner(pi_state, new_owner);
+		postunlock = __rt_mutex_futex_unlock(&pi_state->pi_mutex, &wqh);
+	}
+
+out_unlock:
+	raw_spin_unlock_irq(&pi_state->pi_mutex.wait_lock);
+
+	if (postunlock)
+		rt_mutex_postunlock(&wqh);
+
+	return ret;
+}
+
+/*
+ * Express the locking dependencies for lockdep:
+ */
+static inline void
+double_lock_hb(struct futex_hash_bucket *hb1, struct futex_hash_bucket *hb2)
+{
+	if (hb1 <= hb2) {
+		spin_lock(&hb1->lock);
+		if (hb1 < hb2)
+			spin_lock_nested(&hb2->lock, SINGLE_DEPTH_NESTING);
+	} else { /* hb1 > hb2 */
+		spin_lock(&hb2->lock);
+		spin_lock_nested(&hb1->lock, SINGLE_DEPTH_NESTING);
+	}
+}
+
+static inline void
+double_unlock_hb(struct futex_hash_bucket *hb1, struct futex_hash_bucket *hb2)
+{
+	spin_unlock(&hb1->lock);
+	if (hb1 != hb2)
+		spin_unlock(&hb2->lock);
+}
+
+/*
+ * Wake up waiters matching bitset queued on this futex (uaddr).
+ */
+static int
+futex_wake(u32 __user *uaddr, unsigned int flags, int nr_wake, u32 bitset)
+{
+	struct futex_hash_bucket *hb;
+	struct futex_q *this, *next;
+	union futex_key key = FUTEX_KEY_INIT;
+	int ret;
+	DEFINE_WAKE_Q(wake_q);
+
+	if (!bitset)
+		return -EINVAL;
+
+	ret = get_futex_key(uaddr, flags & FLAGS_SHARED, &key, FUTEX_READ);
+	if (unlikely(ret != 0))
+		return ret;
+
+	hb = hash_futex(&key);
+
+	/* Make sure we really have tasks to wakeup */
+	if (!hb_waiters_pending(hb))
+		return ret;
+
+	spin_lock(&hb->lock);
+
+	plist_for_each_entry_safe(this, next, &hb->chain, list) {
+		if (match_futex (&this->key, &key)) {
+			if (this->pi_state || this->rt_waiter) {
+				ret = -EINVAL;
+				break;
+			}
+
+			/* Check if one of the bits is set in both bitsets */
+			if (!(this->bitset & bitset))
+				continue;
+
+			mark_wake_futex(&wake_q, this);
+			if (++ret >= nr_wake)
+				break;
+		}
+	}
+
+	spin_unlock(&hb->lock);
+	wake_up_q(&wake_q);
+	return ret;
+}
+
+static int futex_atomic_op_inuser(unsigned int encoded_op, u32 __user *uaddr)
+{
+	unsigned int op =	  (encoded_op & 0x70000000) >> 28;
+	unsigned int cmp =	  (encoded_op & 0x0f000000) >> 24;
+	int oparg = sign_extend32((encoded_op & 0x00fff000) >> 12, 11);
+	int cmparg = sign_extend32(encoded_op & 0x00000fff, 11);
+	int oldval, ret;
+
+	if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) {
+		if (oparg < 0 || oparg > 31) {
+			char comm[sizeof(current->comm)];
+			/*
+			 * kill this print and return -EINVAL when userspace
+			 * is sane again
+			 */
+			pr_info_ratelimited("futex_wake_op: %s tries to shift op by %d; fix this program\n",
+					get_task_comm(comm, current), oparg);
+			oparg &= 31;
+		}
+		oparg = 1 << oparg;
+	}
+
+	pagefault_disable();
+	ret = arch_futex_atomic_op_inuser(op, oparg, &oldval, uaddr);
+	pagefault_enable();
+	if (ret)
+		return ret;
+
+	switch (cmp) {
+	case FUTEX_OP_CMP_EQ:
+		return oldval == cmparg;
+	case FUTEX_OP_CMP_NE:
+		return oldval != cmparg;
+	case FUTEX_OP_CMP_LT:
+		return oldval < cmparg;
+	case FUTEX_OP_CMP_GE:
+		return oldval >= cmparg;
+	case FUTEX_OP_CMP_LE:
+		return oldval <= cmparg;
+	case FUTEX_OP_CMP_GT:
+		return oldval > cmparg;
+	default:
+		return -ENOSYS;
+	}
+}
+
+/*
+ * Wake up all waiters hashed on the physical page that is mapped
+ * to this virtual address:
+ */
+static int
+futex_wake_op(u32 __user *uaddr1, unsigned int flags, u32 __user *uaddr2,
+	      int nr_wake, int nr_wake2, int op)
+{
+	union futex_key key1 = FUTEX_KEY_INIT, key2 = FUTEX_KEY_INIT;
+	struct futex_hash_bucket *hb1, *hb2;
+	struct futex_q *this, *next;
+	int ret, op_ret;
+	DEFINE_WAKE_Q(wake_q);
+
+retry:
+	ret = get_futex_key(uaddr1, flags & FLAGS_SHARED, &key1, FUTEX_READ);
+	if (unlikely(ret != 0))
+		return ret;
+	ret = get_futex_key(uaddr2, flags & FLAGS_SHARED, &key2, FUTEX_WRITE);
+	if (unlikely(ret != 0))
+		return ret;
+
+	hb1 = hash_futex(&key1);
+	hb2 = hash_futex(&key2);
+
+retry_private:
+	double_lock_hb(hb1, hb2);
+	op_ret = futex_atomic_op_inuser(op, uaddr2);
+	if (unlikely(op_ret < 0)) {
+		double_unlock_hb(hb1, hb2);
+
+		if (!IS_ENABLED(CONFIG_MMU) ||
+		    unlikely(op_ret != -EFAULT && op_ret != -EAGAIN)) {
+			/*
+			 * we don't get EFAULT from MMU faults if we don't have
+			 * an MMU, but we might get them from range checking
+			 */
+			ret = op_ret;
+			return ret;
+		}
+
+		if (op_ret == -EFAULT) {
+			ret = fault_in_user_writeable(uaddr2);
+			if (ret)
+				return ret;
+		}
+
+		cond_resched();
+		if (!(flags & FLAGS_SHARED))
+			goto retry_private;
+		goto retry;
+	}
+
+	plist_for_each_entry_safe(this, next, &hb1->chain, list) {
+		if (match_futex (&this->key, &key1)) {
+			if (this->pi_state || this->rt_waiter) {
+				ret = -EINVAL;
+				goto out_unlock;
+			}
+			mark_wake_futex(&wake_q, this);
+			if (++ret >= nr_wake)
+				break;
+		}
+	}
+
+	if (op_ret > 0) {
+		op_ret = 0;
+		plist_for_each_entry_safe(this, next, &hb2->chain, list) {
+			if (match_futex (&this->key, &key2)) {
+				if (this->pi_state || this->rt_waiter) {
+					ret = -EINVAL;
+					goto out_unlock;
+				}
+				mark_wake_futex(&wake_q, this);
+				if (++op_ret >= nr_wake2)
+					break;
+			}
+		}
+		ret += op_ret;
+	}
+
+out_unlock:
+	double_unlock_hb(hb1, hb2);
+	wake_up_q(&wake_q);
+	return ret;
+}
+
+/**
+ * requeue_futex() - Requeue a futex_q from one hb to another
+ * @q:		the futex_q to requeue
+ * @hb1:	the source hash_bucket
+ * @hb2:	the target hash_bucket
+ * @key2:	the new key for the requeued futex_q
+ */
+static inline
+void requeue_futex(struct futex_q *q, struct futex_hash_bucket *hb1,
+		   struct futex_hash_bucket *hb2, union futex_key *key2)
+{
+
+	/*
+	 * If key1 and key2 hash to the same bucket, no need to
+	 * requeue.
+	 */
+	if (likely(&hb1->chain != &hb2->chain)) {
+		plist_del(&q->list, &hb1->chain);
+		hb_waiters_dec(hb1);
+		hb_waiters_inc(hb2);
+		plist_add(&q->list, &hb2->chain);
+		q->lock_ptr = &hb2->lock;
+	}
+	q->key = *key2;
+}
+
+static inline bool futex_requeue_pi_prepare(struct futex_q *q,
+					    struct futex_pi_state *pi_state)
+{
+	int old, new;
+
+	/*
+	 * Set state to Q_REQUEUE_PI_IN_PROGRESS unless an early wakeup has
+	 * already set Q_REQUEUE_PI_IGNORE to signal that requeue should
+	 * ignore the waiter.
+	 */
+	old = atomic_read_acquire(&q->requeue_state);
+	do {
+		if (old == Q_REQUEUE_PI_IGNORE)
+			return false;
+
+		/*
+		 * futex_proxy_trylock_atomic() might have set it to
+		 * IN_PROGRESS and a interleaved early wake to WAIT.
+		 *
+		 * It was considered to have an extra state for that
+		 * trylock, but that would just add more conditionals
+		 * all over the place for a dubious value.
+		 */
+		if (old != Q_REQUEUE_PI_NONE)
+			break;
+
+		new = Q_REQUEUE_PI_IN_PROGRESS;
+	} while (!atomic_try_cmpxchg(&q->requeue_state, &old, new));
+
+	q->pi_state = pi_state;
+	return true;
+}
+
+static inline void futex_requeue_pi_complete(struct futex_q *q, int locked)
+{
+	int old, new;
+
+	old = atomic_read_acquire(&q->requeue_state);
+	do {
+		if (old == Q_REQUEUE_PI_IGNORE)
+			return;
+
+		if (locked >= 0) {
+			/* Requeue succeeded. Set DONE or LOCKED */
+			WARN_ON_ONCE(old != Q_REQUEUE_PI_IN_PROGRESS &&
+				     old != Q_REQUEUE_PI_WAIT);
+			new = Q_REQUEUE_PI_DONE + locked;
+		} else if (old == Q_REQUEUE_PI_IN_PROGRESS) {
+			/* Deadlock, no early wakeup interleave */
+			new = Q_REQUEUE_PI_NONE;
+		} else {
+			/* Deadlock, early wakeup interleave. */
+			WARN_ON_ONCE(old != Q_REQUEUE_PI_WAIT);
+			new = Q_REQUEUE_PI_IGNORE;
+		}
+	} while (!atomic_try_cmpxchg(&q->requeue_state, &old, new));
+
+#ifdef CONFIG_PREEMPT_RT
+	/* If the waiter interleaved with the requeue let it know */
+	if (unlikely(old == Q_REQUEUE_PI_WAIT))
+		rcuwait_wake_up(&q->requeue_wait);
+#endif
+}
+
+static inline int futex_requeue_pi_wakeup_sync(struct futex_q *q)
+{
+	int old, new;
+
+	old = atomic_read_acquire(&q->requeue_state);
+	do {
+		/* Is requeue done already? */
+		if (old >= Q_REQUEUE_PI_DONE)
+			return old;
+
+		/*
+		 * If not done, then tell the requeue code to either ignore
+		 * the waiter or to wake it up once the requeue is done.
+		 */
+		new = Q_REQUEUE_PI_WAIT;
+		if (old == Q_REQUEUE_PI_NONE)
+			new = Q_REQUEUE_PI_IGNORE;
+	} while (!atomic_try_cmpxchg(&q->requeue_state, &old, new));
+
+	/* If the requeue was in progress, wait for it to complete */
+	if (old == Q_REQUEUE_PI_IN_PROGRESS) {
+#ifdef CONFIG_PREEMPT_RT
+		rcuwait_wait_event(&q->requeue_wait,
+				   atomic_read(&q->requeue_state) != Q_REQUEUE_PI_WAIT,
+				   TASK_UNINTERRUPTIBLE);
+#else
+		(void)atomic_cond_read_relaxed(&q->requeue_state, VAL != Q_REQUEUE_PI_WAIT);
+#endif
+	}
+
+	/*
+	 * Requeue is now either prohibited or complete. Reread state
+	 * because during the wait above it might have changed. Nothing
+	 * will modify q->requeue_state after this point.
+	 */
+	return atomic_read(&q->requeue_state);
+}
+
+/**
+ * requeue_pi_wake_futex() - Wake a task that acquired the lock during requeue
+ * @q:		the futex_q
+ * @key:	the key of the requeue target futex
+ * @hb:		the hash_bucket of the requeue target futex
+ *
+ * During futex_requeue, with requeue_pi=1, it is possible to acquire the
+ * target futex if it is uncontended or via a lock steal.
+ *
+ * 1) Set @q::key to the requeue target futex key so the waiter can detect
+ *    the wakeup on the right futex.
+ *
+ * 2) Dequeue @q from the hash bucket.
+ *
+ * 3) Set @q::rt_waiter to NULL so the woken up task can detect atomic lock
+ *    acquisition.
+ *
+ * 4) Set the q->lock_ptr to the requeue target hb->lock for the case that
+ *    the waiter has to fixup the pi state.
+ *
+ * 5) Complete the requeue state so the waiter can make progress. After
+ *    this point the waiter task can return from the syscall immediately in
+ *    case that the pi state does not have to be fixed up.
+ *
+ * 6) Wake the waiter task.
+ *
+ * Must be called with both q->lock_ptr and hb->lock held.
+ */
+static inline
+void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key,
+			   struct futex_hash_bucket *hb)
+{
+	q->key = *key;
+
+	__unqueue_futex(q);
+
+	WARN_ON(!q->rt_waiter);
+	q->rt_waiter = NULL;
+
+	q->lock_ptr = &hb->lock;
+
+	/* Signal locked state to the waiter */
+	futex_requeue_pi_complete(q, 1);
+	wake_up_state(q->task, TASK_NORMAL);
+}
+
+/**
+ * futex_proxy_trylock_atomic() - Attempt an atomic lock for the top waiter
+ * @pifutex:		the user address of the to futex
+ * @hb1:		the from futex hash bucket, must be locked by the caller
+ * @hb2:		the to futex hash bucket, must be locked by the caller
+ * @key1:		the from futex key
+ * @key2:		the to futex key
+ * @ps:			address to store the pi_state pointer
+ * @exiting:		Pointer to store the task pointer of the owner task
+ *			which is in the middle of exiting
+ * @set_waiters:	force setting the FUTEX_WAITERS bit (1) or not (0)
+ *
+ * Try and get the lock on behalf of the top waiter if we can do it atomically.
+ * Wake the top waiter if we succeed.  If the caller specified set_waiters,
+ * then direct futex_lock_pi_atomic() to force setting the FUTEX_WAITERS bit.
+ * hb1 and hb2 must be held by the caller.
+ *
+ * @exiting is only set when the return value is -EBUSY. If so, this holds
+ * a refcount on the exiting task on return and the caller needs to drop it
+ * after waiting for the exit to complete.
+ *
+ * Return:
+ *  -  0 - failed to acquire the lock atomically;
+ *  - >0 - acquired the lock, return value is vpid of the top_waiter
+ *  - <0 - error
+ */
+static int
+futex_proxy_trylock_atomic(u32 __user *pifutex, struct futex_hash_bucket *hb1,
+			   struct futex_hash_bucket *hb2, union futex_key *key1,
+			   union futex_key *key2, struct futex_pi_state **ps,
+			   struct task_struct **exiting, int set_waiters)
+{
+	struct futex_q *top_waiter = NULL;
+	u32 curval;
+	int ret;
+
+	if (get_futex_value_locked(&curval, pifutex))
+		return -EFAULT;
+
+	if (unlikely(should_fail_futex(true)))
+		return -EFAULT;
+
+	/*
+	 * Find the top_waiter and determine if there are additional waiters.
+	 * If the caller intends to requeue more than 1 waiter to pifutex,
+	 * force futex_lock_pi_atomic() to set the FUTEX_WAITERS bit now,
+	 * as we have means to handle the possible fault.  If not, don't set
+	 * the bit unnecessarily as it will force the subsequent unlock to enter
+	 * the kernel.
+	 */
+	top_waiter = futex_top_waiter(hb1, key1);
+
+	/* There are no waiters, nothing for us to do. */
+	if (!top_waiter)
+		return 0;
+
+	/*
+	 * Ensure that this is a waiter sitting in futex_wait_requeue_pi()
+	 * and waiting on the 'waitqueue' futex which is always !PI.
+	 */
+	if (!top_waiter->rt_waiter || top_waiter->pi_state)
+		return -EINVAL;
+
+	/* Ensure we requeue to the expected futex. */
+	if (!match_futex(top_waiter->requeue_pi_key, key2))
+		return -EINVAL;
+
+	/* Ensure that this does not race against an early wakeup */
+	if (!futex_requeue_pi_prepare(top_waiter, NULL))
+		return -EAGAIN;
+
+	/*
+	 * Try to take the lock for top_waiter and set the FUTEX_WAITERS bit
+	 * in the contended case or if @set_waiters is true.
+	 *
+	 * In the contended case PI state is attached to the lock owner. If
+	 * the user space lock can be acquired then PI state is attached to
+	 * the new owner (@top_waiter->task) when @set_waiters is true.
+	 */
+	ret = futex_lock_pi_atomic(pifutex, hb2, key2, ps, top_waiter->task,
+				   exiting, set_waiters);
+	if (ret == 1) {
+		/*
+		 * Lock was acquired in user space and PI state was
+		 * attached to @top_waiter->task. That means state is fully
+		 * consistent and the waiter can return to user space
+		 * immediately after the wakeup.
+		 */
+		requeue_pi_wake_futex(top_waiter, key2, hb2);
+	} else if (ret < 0) {
+		/* Rewind top_waiter::requeue_state */
+		futex_requeue_pi_complete(top_waiter, ret);
+	} else {
+		/*
+		 * futex_lock_pi_atomic() did not acquire the user space
+		 * futex, but managed to establish the proxy lock and pi
+		 * state. top_waiter::requeue_state cannot be fixed up here
+		 * because the waiter is not enqueued on the rtmutex
+		 * yet. This is handled at the callsite depending on the
+		 * result of rt_mutex_start_proxy_lock() which is
+		 * guaranteed to be reached with this function returning 0.
+		 */
+	}
+	return ret;
+}
+
+/**
+ * futex_requeue() - Requeue waiters from uaddr1 to uaddr2
+ * @uaddr1:	source futex user address
+ * @flags:	futex flags (FLAGS_SHARED, etc.)
+ * @uaddr2:	target futex user address
+ * @nr_wake:	number of waiters to wake (must be 1 for requeue_pi)
+ * @nr_requeue:	number of waiters to requeue (0-INT_MAX)
+ * @cmpval:	@uaddr1 expected value (or %NULL)
+ * @requeue_pi:	if we are attempting to requeue from a non-pi futex to a
+ *		pi futex (pi to pi requeue is not supported)
+ *
+ * Requeue waiters on uaddr1 to uaddr2. In the requeue_pi case, try to acquire
+ * uaddr2 atomically on behalf of the top waiter.
+ *
+ * Return:
+ *  - >=0 - on success, the number of tasks requeued or woken;
+ *  -  <0 - on error
+ */
+static int futex_requeue(u32 __user *uaddr1, unsigned int flags,
+			 u32 __user *uaddr2, int nr_wake, int nr_requeue,
+			 u32 *cmpval, int requeue_pi)
+{
+	union futex_key key1 = FUTEX_KEY_INIT, key2 = FUTEX_KEY_INIT;
+	int task_count = 0, ret;
+	struct futex_pi_state *pi_state = NULL;
+	struct futex_hash_bucket *hb1, *hb2;
+	struct futex_q *this, *next;
+	DEFINE_WAKE_Q(wake_q);
+
+	if (nr_wake < 0 || nr_requeue < 0)
+		return -EINVAL;
+
+	/*
+	 * When PI not supported: return -ENOSYS if requeue_pi is true,
+	 * consequently the compiler knows requeue_pi is always false past
+	 * this point which will optimize away all the conditional code
+	 * further down.
+	 */
+	if (!IS_ENABLED(CONFIG_FUTEX_PI) && requeue_pi)
+		return -ENOSYS;
+
+	if (requeue_pi) {
+		/*
+		 * Requeue PI only works on two distinct uaddrs. This
+		 * check is only valid for private futexes. See below.
+		 */
+		if (uaddr1 == uaddr2)
+			return -EINVAL;
+
+		/*
+		 * futex_requeue() allows the caller to define the number
+		 * of waiters to wake up via the @nr_wake argument. With
+		 * REQUEUE_PI, waking up more than one waiter is creating
+		 * more problems than it solves. Waking up a waiter makes
+		 * only sense if the PI futex @uaddr2 is uncontended as
+		 * this allows the requeue code to acquire the futex
+		 * @uaddr2 before waking the waiter. The waiter can then
+		 * return to user space without further action. A secondary
+		 * wakeup would just make the futex_wait_requeue_pi()
+		 * handling more complex, because that code would have to
+		 * look up pi_state and do more or less all the handling
+		 * which the requeue code has to do for the to be requeued
+		 * waiters. So restrict the number of waiters to wake to
+		 * one, and only wake it up when the PI futex is
+		 * uncontended. Otherwise requeue it and let the unlock of
+		 * the PI futex handle the wakeup.
+		 *
+		 * All REQUEUE_PI users, e.g. pthread_cond_signal() and
+		 * pthread_cond_broadcast() must use nr_wake=1.
+		 */
+		if (nr_wake != 1)
+			return -EINVAL;
+
+		/*
+		 * requeue_pi requires a pi_state, try to allocate it now
+		 * without any locks in case it fails.
+		 */
+		if (refill_pi_state_cache())
+			return -ENOMEM;
+	}
+
+retry:
+	ret = get_futex_key(uaddr1, flags & FLAGS_SHARED, &key1, FUTEX_READ);
+	if (unlikely(ret != 0))
+		return ret;
+	ret = get_futex_key(uaddr2, flags & FLAGS_SHARED, &key2,
+			    requeue_pi ? FUTEX_WRITE : FUTEX_READ);
+	if (unlikely(ret != 0))
+		return ret;
+
+	/*
+	 * The check above which compares uaddrs is not sufficient for
+	 * shared futexes. We need to compare the keys:
+	 */
+	if (requeue_pi && match_futex(&key1, &key2))
+		return -EINVAL;
+
+	hb1 = hash_futex(&key1);
+	hb2 = hash_futex(&key2);
+
+retry_private:
+	hb_waiters_inc(hb2);
+	double_lock_hb(hb1, hb2);
+
+	if (likely(cmpval != NULL)) {
+		u32 curval;
+
+		ret = get_futex_value_locked(&curval, uaddr1);
+
+		if (unlikely(ret)) {
+			double_unlock_hb(hb1, hb2);
+			hb_waiters_dec(hb2);
+
+			ret = get_user(curval, uaddr1);
+			if (ret)
+				return ret;
+
+			if (!(flags & FLAGS_SHARED))
+				goto retry_private;
+
+			goto retry;
+		}
+		if (curval != *cmpval) {
+			ret = -EAGAIN;
+			goto out_unlock;
+		}
+	}
+
+	if (requeue_pi) {
+		struct task_struct *exiting = NULL;
+
+		/*
+		 * Attempt to acquire uaddr2 and wake the top waiter. If we
+		 * intend to requeue waiters, force setting the FUTEX_WAITERS
+		 * bit.  We force this here where we are able to easily handle
+		 * faults rather in the requeue loop below.
+		 *
+		 * Updates topwaiter::requeue_state if a top waiter exists.
+		 */
+		ret = futex_proxy_trylock_atomic(uaddr2, hb1, hb2, &key1,
+						 &key2, &pi_state,
+						 &exiting, nr_requeue);
+
+		/*
+		 * At this point the top_waiter has either taken uaddr2 or
+		 * is waiting on it. In both cases pi_state has been
+		 * established and an initial refcount on it. In case of an
+		 * error there's nothing.
+		 *
+		 * The top waiter's requeue_state is up to date:
+		 *
+		 *  - If the lock was acquired atomically (ret == 1), then
+		 *    the state is Q_REQUEUE_PI_LOCKED.
+		 *
+		 *    The top waiter has been dequeued and woken up and can
+		 *    return to user space immediately. The kernel/user
+		 *    space state is consistent. In case that there must be
+		 *    more waiters requeued the WAITERS bit in the user
+		 *    space futex is set so the top waiter task has to go
+		 *    into the syscall slowpath to unlock the futex. This
+		 *    will block until this requeue operation has been
+		 *    completed and the hash bucket locks have been
+		 *    dropped.
+		 *
+		 *  - If the trylock failed with an error (ret < 0) then
+		 *    the state is either Q_REQUEUE_PI_NONE, i.e. "nothing
+		 *    happened", or Q_REQUEUE_PI_IGNORE when there was an
+		 *    interleaved early wakeup.
+		 *
+		 *  - If the trylock did not succeed (ret == 0) then the
+		 *    state is either Q_REQUEUE_PI_IN_PROGRESS or
+		 *    Q_REQUEUE_PI_WAIT if an early wakeup interleaved.
+		 *    This will be cleaned up in the loop below, which
+		 *    cannot fail because futex_proxy_trylock_atomic() did
+		 *    the same sanity checks for requeue_pi as the loop
+		 *    below does.
+		 */
+		switch (ret) {
+		case 0:
+			/* We hold a reference on the pi state. */
+			break;
+
+		case 1:
+			/*
+			 * futex_proxy_trylock_atomic() acquired the user space
+			 * futex. Adjust task_count.
+			 */
+			task_count++;
+			ret = 0;
+			break;
+
+		/*
+		 * If the above failed, then pi_state is NULL and
+		 * waiter::requeue_state is correct.
+		 */
+		case -EFAULT:
+			double_unlock_hb(hb1, hb2);
+			hb_waiters_dec(hb2);
+			ret = fault_in_user_writeable(uaddr2);
+			if (!ret)
+				goto retry;
+			return ret;
+		case -EBUSY:
+		case -EAGAIN:
+			/*
+			 * Two reasons for this:
+			 * - EBUSY: Owner is exiting and we just wait for the
+			 *   exit to complete.
+			 * - EAGAIN: The user space value changed.
+			 */
+			double_unlock_hb(hb1, hb2);
+			hb_waiters_dec(hb2);
+			/*
+			 * Handle the case where the owner is in the middle of
+			 * exiting. Wait for the exit to complete otherwise
+			 * this task might loop forever, aka. live lock.
+			 */
+			wait_for_owner_exiting(ret, exiting);
+			cond_resched();
+			goto retry;
+		default:
+			goto out_unlock;
+		}
+	}
+
+	plist_for_each_entry_safe(this, next, &hb1->chain, list) {
+		if (task_count - nr_wake >= nr_requeue)
+			break;
+
+		if (!match_futex(&this->key, &key1))
+			continue;
+
+		/*
+		 * FUTEX_WAIT_REQUEUE_PI and FUTEX_CMP_REQUEUE_PI should always
+		 * be paired with each other and no other futex ops.
+		 *
+		 * We should never be requeueing a futex_q with a pi_state,
+		 * which is awaiting a futex_unlock_pi().
+		 */
+		if ((requeue_pi && !this->rt_waiter) ||
+		    (!requeue_pi && this->rt_waiter) ||
+		    this->pi_state) {
+			ret = -EINVAL;
+			break;
+		}
+
+		/* Plain futexes just wake or requeue and are done */
+		if (!requeue_pi) {
+			if (++task_count <= nr_wake)
+				mark_wake_futex(&wake_q, this);
+			else
+				requeue_futex(this, hb1, hb2, &key2);
+			continue;
+		}
+
+		/* Ensure we requeue to the expected futex for requeue_pi. */
+		if (!match_futex(this->requeue_pi_key, &key2)) {
+			ret = -EINVAL;
+			break;
+		}
+
+		/*
+		 * Requeue nr_requeue waiters and possibly one more in the case
+		 * of requeue_pi if we couldn't acquire the lock atomically.
+		 *
+		 * Prepare the waiter to take the rt_mutex. Take a refcount
+		 * on the pi_state and store the pointer in the futex_q
+		 * object of the waiter.
+		 */
+		get_pi_state(pi_state);
+
+		/* Don't requeue when the waiter is already on the way out. */
+		if (!futex_requeue_pi_prepare(this, pi_state)) {
+			/*
+			 * Early woken waiter signaled that it is on the
+			 * way out. Drop the pi_state reference and try the
+			 * next waiter. @this->pi_state is still NULL.
+			 */
+			put_pi_state(pi_state);
+			continue;
+		}
+
+		ret = rt_mutex_start_proxy_lock(&pi_state->pi_mutex,
+						this->rt_waiter,
+						this->task);
+
+		if (ret == 1) {
+			/*
+			 * We got the lock. We do neither drop the refcount
+			 * on pi_state nor clear this->pi_state because the
+			 * waiter needs the pi_state for cleaning up the
+			 * user space value. It will drop the refcount
+			 * after doing so. this::requeue_state is updated
+			 * in the wakeup as well.
+			 */
+			requeue_pi_wake_futex(this, &key2, hb2);
+			task_count++;
+		} else if (!ret) {
+			/* Waiter is queued, move it to hb2 */
+			requeue_futex(this, hb1, hb2, &key2);
+			futex_requeue_pi_complete(this, 0);
+			task_count++;
+		} else {
+			/*
+			 * rt_mutex_start_proxy_lock() detected a potential
+			 * deadlock when we tried to queue that waiter.
+			 * Drop the pi_state reference which we took above
+			 * and remove the pointer to the state from the
+			 * waiters futex_q object.
+			 */
+			this->pi_state = NULL;
+			put_pi_state(pi_state);
+			futex_requeue_pi_complete(this, ret);
+			/*
+			 * We stop queueing more waiters and let user space
+			 * deal with the mess.
+			 */
+			break;
+		}
+	}
+
+	/*
+	 * We took an extra initial reference to the pi_state in
+	 * futex_proxy_trylock_atomic(). We need to drop it here again.
+	 */
+	put_pi_state(pi_state);
+
+out_unlock:
+	double_unlock_hb(hb1, hb2);
+	wake_up_q(&wake_q);
+	hb_waiters_dec(hb2);
+	return ret ? ret : task_count;
+}
+
+/* The key must be already stored in q->key. */
+static inline struct futex_hash_bucket *queue_lock(struct futex_q *q)
+	__acquires(&hb->lock)
+{
+	struct futex_hash_bucket *hb;
+
+	hb = hash_futex(&q->key);
+
+	/*
+	 * Increment the counter before taking the lock so that
+	 * a potential waker won't miss a to-be-slept task that is
+	 * waiting for the spinlock. This is safe as all queue_lock()
+	 * users end up calling queue_me(). Similarly, for housekeeping,
+	 * decrement the counter at queue_unlock() when some error has
+	 * occurred and we don't end up adding the task to the list.
+	 */
+	hb_waiters_inc(hb); /* implies smp_mb(); (A) */
+
+	q->lock_ptr = &hb->lock;
+
+	spin_lock(&hb->lock);
+	return hb;
+}
+
+static inline void
+queue_unlock(struct futex_hash_bucket *hb)
+	__releases(&hb->lock)
+{
+	spin_unlock(&hb->lock);
+	hb_waiters_dec(hb);
+}
+
+static inline void __queue_me(struct futex_q *q, struct futex_hash_bucket *hb)
+{
+	int prio;
+
+	/*
+	 * The priority used to register this element is
+	 * - either the real thread-priority for the real-time threads
+	 * (i.e. threads with a priority lower than MAX_RT_PRIO)
+	 * - or MAX_RT_PRIO for non-RT threads.
+	 * Thus, all RT-threads are woken first in priority order, and
+	 * the others are woken last, in FIFO order.
+	 */
+	prio = min(current->normal_prio, MAX_RT_PRIO);
+
+	plist_node_init(&q->list, prio);
+	plist_add(&q->list, &hb->chain);
+	q->task = current;
+}
+
+/**
+ * queue_me() - Enqueue the futex_q on the futex_hash_bucket
+ * @q:	The futex_q to enqueue
+ * @hb:	The destination hash bucket
+ *
+ * The hb->lock must be held by the caller, and is released here. A call to
+ * queue_me() is typically paired with exactly one call to unqueue_me().  The
+ * exceptions involve the PI related operations, which may use unqueue_me_pi()
+ * or nothing if the unqueue is done as part of the wake process and the unqueue
+ * state is implicit in the state of woken task (see futex_wait_requeue_pi() for
+ * an example).
+ */
+static inline void queue_me(struct futex_q *q, struct futex_hash_bucket *hb)
+	__releases(&hb->lock)
+{
+	__queue_me(q, hb);
+	spin_unlock(&hb->lock);
+}
+
+/**
+ * unqueue_me() - Remove the futex_q from its futex_hash_bucket
+ * @q:	The futex_q to unqueue
+ *
+ * The q->lock_ptr must not be held by the caller. A call to unqueue_me() must
+ * be paired with exactly one earlier call to queue_me().
+ *
+ * Return:
+ *  - 1 - if the futex_q was still queued (and we removed unqueued it);
+ *  - 0 - if the futex_q was already removed by the waking thread
+ */
+static int unqueue_me(struct futex_q *q)
+{
+	spinlock_t *lock_ptr;
+	int ret = 0;
+
+	/* In the common case we don't take the spinlock, which is nice. */
+retry:
+	/*
+	 * q->lock_ptr can change between this read and the following spin_lock.
+	 * Use READ_ONCE to forbid the compiler from reloading q->lock_ptr and
+	 * optimizing lock_ptr out of the logic below.
+	 */
+	lock_ptr = READ_ONCE(q->lock_ptr);
+	if (lock_ptr != NULL) {
+		spin_lock(lock_ptr);
+		/*
+		 * q->lock_ptr can change between reading it and
+		 * spin_lock(), causing us to take the wrong lock.  This
+		 * corrects the race condition.
+		 *
+		 * Reasoning goes like this: if we have the wrong lock,
+		 * q->lock_ptr must have changed (maybe several times)
+		 * between reading it and the spin_lock().  It can
+		 * change again after the spin_lock() but only if it was
+		 * already changed before the spin_lock().  It cannot,
+		 * however, change back to the original value.  Therefore
+		 * we can detect whether we acquired the correct lock.
+		 */
+		if (unlikely(lock_ptr != q->lock_ptr)) {
+			spin_unlock(lock_ptr);
+			goto retry;
+		}
+		__unqueue_futex(q);
+
+		BUG_ON(q->pi_state);
+
+		spin_unlock(lock_ptr);
+		ret = 1;
+	}
+
+	return ret;
+}
+
+/*
+ * PI futexes can not be requeued and must remove themselves from the
+ * hash bucket. The hash bucket lock (i.e. lock_ptr) is held.
+ */
+static void unqueue_me_pi(struct futex_q *q)
+{
+	__unqueue_futex(q);
+
+	BUG_ON(!q->pi_state);
+	put_pi_state(q->pi_state);
+	q->pi_state = NULL;
+}
+
+static int __fixup_pi_state_owner(u32 __user *uaddr, struct futex_q *q,
+				  struct task_struct *argowner)
+{
+	struct futex_pi_state *pi_state = q->pi_state;
+	struct task_struct *oldowner, *newowner;
+	u32 uval, curval, newval, newtid;
+	int err = 0;
+
+	oldowner = pi_state->owner;
+
+	/*
+	 * We are here because either:
+	 *
+	 *  - we stole the lock and pi_state->owner needs updating to reflect
+	 *    that (@argowner == current),
+	 *
+	 * or:
+	 *
+	 *  - someone stole our lock and we need to fix things to point to the
+	 *    new owner (@argowner == NULL).
+	 *
+	 * Either way, we have to replace the TID in the user space variable.
+	 * This must be atomic as we have to preserve the owner died bit here.
+	 *
+	 * Note: We write the user space value _before_ changing the pi_state
+	 * because we can fault here. Imagine swapped out pages or a fork
+	 * that marked all the anonymous memory readonly for cow.
+	 *
+	 * Modifying pi_state _before_ the user space value would leave the
+	 * pi_state in an inconsistent state when we fault here, because we
+	 * need to drop the locks to handle the fault. This might be observed
+	 * in the PID checks when attaching to PI state .
+	 */
+retry:
+	if (!argowner) {
+		if (oldowner != current) {
+			/*
+			 * We raced against a concurrent self; things are
+			 * already fixed up. Nothing to do.
+			 */
+			return 0;
+		}
+
+		if (__rt_mutex_futex_trylock(&pi_state->pi_mutex)) {
+			/* We got the lock. pi_state is correct. Tell caller. */
+			return 1;
+		}
+
+		/*
+		 * The trylock just failed, so either there is an owner or
+		 * there is a higher priority waiter than this one.
+		 */
+		newowner = rt_mutex_owner(&pi_state->pi_mutex);
+		/*
+		 * If the higher priority waiter has not yet taken over the
+		 * rtmutex then newowner is NULL. We can't return here with
+		 * that state because it's inconsistent vs. the user space
+		 * state. So drop the locks and try again. It's a valid
+		 * situation and not any different from the other retry
+		 * conditions.
+		 */
+		if (unlikely(!newowner)) {
+			err = -EAGAIN;
+			goto handle_err;
+		}
+	} else {
+		WARN_ON_ONCE(argowner != current);
+		if (oldowner == current) {
+			/*
+			 * We raced against a concurrent self; things are
+			 * already fixed up. Nothing to do.
+			 */
+			return 1;
+		}
+		newowner = argowner;
+	}
+
+	newtid = task_pid_vnr(newowner) | FUTEX_WAITERS;
+	/* Owner died? */
+	if (!pi_state->owner)
+		newtid |= FUTEX_OWNER_DIED;
+
+	err = get_futex_value_locked(&uval, uaddr);
+	if (err)
+		goto handle_err;
+
+	for (;;) {
+		newval = (uval & FUTEX_OWNER_DIED) | newtid;
+
+		err = cmpxchg_futex_value_locked(&curval, uaddr, uval, newval);
+		if (err)
+			goto handle_err;
+
+		if (curval == uval)
+			break;
+		uval = curval;
+	}
+
+	/*
+	 * We fixed up user space. Now we need to fix the pi_state
+	 * itself.
+	 */
+	pi_state_update_owner(pi_state, newowner);
+
+	return argowner == current;
+
+	/*
+	 * In order to reschedule or handle a page fault, we need to drop the
+	 * locks here. In the case of a fault, this gives the other task
+	 * (either the highest priority waiter itself or the task which stole
+	 * the rtmutex) the chance to try the fixup of the pi_state. So once we
+	 * are back from handling the fault we need to check the pi_state after
+	 * reacquiring the locks and before trying to do another fixup. When
+	 * the fixup has been done already we simply return.
+	 *
+	 * Note: we hold both hb->lock and pi_mutex->wait_lock. We can safely
+	 * drop hb->lock since the caller owns the hb -> futex_q relation.
+	 * Dropping the pi_mutex->wait_lock requires the state revalidate.
+	 */
+handle_err:
+	raw_spin_unlock_irq(&pi_state->pi_mutex.wait_lock);
+	spin_unlock(q->lock_ptr);
+
+	switch (err) {
+	case -EFAULT:
+		err = fault_in_user_writeable(uaddr);
+		break;
+
+	case -EAGAIN:
+		cond_resched();
+		err = 0;
+		break;
+
+	default:
+		WARN_ON_ONCE(1);
+		break;
+	}
+
+	spin_lock(q->lock_ptr);
+	raw_spin_lock_irq(&pi_state->pi_mutex.wait_lock);
+
+	/*
+	 * Check if someone else fixed it for us:
+	 */
+	if (pi_state->owner != oldowner)
+		return argowner == current;
+
+	/* Retry if err was -EAGAIN or the fault in succeeded */
+	if (!err)
+		goto retry;
+
+	/*
+	 * fault_in_user_writeable() failed so user state is immutable. At
+	 * best we can make the kernel state consistent but user state will
+	 * be most likely hosed and any subsequent unlock operation will be
+	 * rejected due to PI futex rule [10].
+	 *
+	 * Ensure that the rtmutex owner is also the pi_state owner despite
+	 * the user space value claiming something different. There is no
+	 * point in unlocking the rtmutex if current is the owner as it
+	 * would need to wait until the next waiter has taken the rtmutex
+	 * to guarantee consistent state. Keep it simple. Userspace asked
+	 * for this wreckaged state.
+	 *
+	 * The rtmutex has an owner - either current or some other
+	 * task. See the EAGAIN loop above.
+	 */
+	pi_state_update_owner(pi_state, rt_mutex_owner(&pi_state->pi_mutex));
+
+	return err;
+}
+
+static int fixup_pi_state_owner(u32 __user *uaddr, struct futex_q *q,
+				struct task_struct *argowner)
+{
+	struct futex_pi_state *pi_state = q->pi_state;
+	int ret;
+
+	lockdep_assert_held(q->lock_ptr);
+
+	raw_spin_lock_irq(&pi_state->pi_mutex.wait_lock);
+	ret = __fixup_pi_state_owner(uaddr, q, argowner);
+	raw_spin_unlock_irq(&pi_state->pi_mutex.wait_lock);
+	return ret;
+}
+
+static long futex_wait_restart(struct restart_block *restart);
+
+/**
+ * fixup_owner() - Post lock pi_state and corner case management
+ * @uaddr:	user address of the futex
+ * @q:		futex_q (contains pi_state and access to the rt_mutex)
+ * @locked:	if the attempt to take the rt_mutex succeeded (1) or not (0)
+ *
+ * After attempting to lock an rt_mutex, this function is called to cleanup
+ * the pi_state owner as well as handle race conditions that may allow us to
+ * acquire the lock. Must be called with the hb lock held.
+ *
+ * Return:
+ *  -  1 - success, lock taken;
+ *  -  0 - success, lock not taken;
+ *  - <0 - on error (-EFAULT)
+ */
+static int fixup_owner(u32 __user *uaddr, struct futex_q *q, int locked)
+{
+	if (locked) {
+		/*
+		 * Got the lock. We might not be the anticipated owner if we
+		 * did a lock-steal - fix up the PI-state in that case:
+		 *
+		 * Speculative pi_state->owner read (we don't hold wait_lock);
+		 * since we own the lock pi_state->owner == current is the
+		 * stable state, anything else needs more attention.
+		 */
+		if (q->pi_state->owner != current)
+			return fixup_pi_state_owner(uaddr, q, current);
+		return 1;
+	}
+
+	/*
+	 * If we didn't get the lock; check if anybody stole it from us. In
+	 * that case, we need to fix up the uval to point to them instead of
+	 * us, otherwise bad things happen. [10]
+	 *
+	 * Another speculative read; pi_state->owner == current is unstable
+	 * but needs our attention.
+	 */
+	if (q->pi_state->owner == current)
+		return fixup_pi_state_owner(uaddr, q, NULL);
+
+	/*
+	 * Paranoia check. If we did not take the lock, then we should not be
+	 * the owner of the rt_mutex. Warn and establish consistent state.
+	 */
+	if (WARN_ON_ONCE(rt_mutex_owner(&q->pi_state->pi_mutex) == current))
+		return fixup_pi_state_owner(uaddr, q, current);
+
+	return 0;
+}
+
+/**
+ * futex_wait_queue_me() - queue_me() and wait for wakeup, timeout, or signal
+ * @hb:		the futex hash bucket, must be locked by the caller
+ * @q:		the futex_q to queue up on
+ * @timeout:	the prepared hrtimer_sleeper, or null for no timeout
+ */
+static void futex_wait_queue_me(struct futex_hash_bucket *hb, struct futex_q *q,
+				struct hrtimer_sleeper *timeout)
+{
+	/*
+	 * The task state is guaranteed to be set before another task can
+	 * wake it. set_current_state() is implemented using smp_store_mb() and
+	 * queue_me() calls spin_unlock() upon completion, both serializing
+	 * access to the hash list and forcing another memory barrier.
+	 */
+	set_current_state(TASK_INTERRUPTIBLE);
+	queue_me(q, hb);
+
+	/* Arm the timer */
+	if (timeout)
+		hrtimer_sleeper_start_expires(timeout, HRTIMER_MODE_ABS);
+
+	/*
+	 * If we have been removed from the hash list, then another task
+	 * has tried to wake us, and we can skip the call to schedule().
+	 */
+	if (likely(!plist_node_empty(&q->list))) {
+		/*
+		 * If the timer has already expired, current will already be
+		 * flagged for rescheduling. Only call schedule if there
+		 * is no timeout, or if it has yet to expire.
+		 */
+		if (!timeout || timeout->task)
+			freezable_schedule();
+	}
+	__set_current_state(TASK_RUNNING);
+}
+
+/**
+ * futex_wait_setup() - Prepare to wait on a futex
+ * @uaddr:	the futex userspace address
+ * @val:	the expected value
+ * @flags:	futex flags (FLAGS_SHARED, etc.)
+ * @q:		the associated futex_q
+ * @hb:		storage for hash_bucket pointer to be returned to caller
+ *
+ * Setup the futex_q and locate the hash_bucket.  Get the futex value and
+ * compare it with the expected value.  Handle atomic faults internally.
+ * Return with the hb lock held on success, and unlocked on failure.
+ *
+ * Return:
+ *  -  0 - uaddr contains val and hb has been locked;
+ *  - <1 - -EFAULT or -EWOULDBLOCK (uaddr does not contain val) and hb is unlocked
+ */
+static int futex_wait_setup(u32 __user *uaddr, u32 val, unsigned int flags,
+			   struct futex_q *q, struct futex_hash_bucket **hb)
+{
+	u32 uval;
+	int ret;
+
+	/*
+	 * Access the page AFTER the hash-bucket is locked.
+	 * Order is important:
+	 *
+	 *   Userspace waiter: val = var; if (cond(val)) futex_wait(&var, val);
+	 *   Userspace waker:  if (cond(var)) { var = new; futex_wake(&var); }
+	 *
+	 * The basic logical guarantee of a futex is that it blocks ONLY
+	 * if cond(var) is known to be true at the time of blocking, for
+	 * any cond.  If we locked the hash-bucket after testing *uaddr, that
+	 * would open a race condition where we could block indefinitely with
+	 * cond(var) false, which would violate the guarantee.
+	 *
+	 * On the other hand, we insert q and release the hash-bucket only
+	 * after testing *uaddr.  This guarantees that futex_wait() will NOT
+	 * absorb a wakeup if *uaddr does not match the desired values
+	 * while the syscall executes.
+	 */
+retry:
+	ret = get_futex_key(uaddr, flags & FLAGS_SHARED, &q->key, FUTEX_READ);
+	if (unlikely(ret != 0))
+		return ret;
+
+retry_private:
+	*hb = queue_lock(q);
+
+	ret = get_futex_value_locked(&uval, uaddr);
+
+	if (ret) {
+		queue_unlock(*hb);
+
+		ret = get_user(uval, uaddr);
+		if (ret)
+			return ret;
+
+		if (!(flags & FLAGS_SHARED))
+			goto retry_private;
+
+		goto retry;
+	}
+
+	if (uval != val) {
+		queue_unlock(*hb);
+		ret = -EWOULDBLOCK;
+	}
+
+	return ret;
+}
+
+static int futex_wait(u32 __user *uaddr, unsigned int flags, u32 val,
+		      ktime_t *abs_time, u32 bitset)
+{
+	struct hrtimer_sleeper timeout, *to;
+	struct restart_block *restart;
+	struct futex_hash_bucket *hb;
+	struct futex_q q = futex_q_init;
+	int ret;
+
+	if (!bitset)
+		return -EINVAL;
+	q.bitset = bitset;
+
+	to = futex_setup_timer(abs_time, &timeout, flags,
+			       current->timer_slack_ns);
+retry:
+	/*
+	 * Prepare to wait on uaddr. On success, it holds hb->lock and q
+	 * is initialized.
+	 */
+	ret = futex_wait_setup(uaddr, val, flags, &q, &hb);
+	if (ret)
+		goto out;
+
+	/* queue_me and wait for wakeup, timeout, or a signal. */
+	futex_wait_queue_me(hb, &q, to);
+
+	/* If we were woken (and unqueued), we succeeded, whatever. */
+	ret = 0;
+	if (!unqueue_me(&q))
+		goto out;
+	ret = -ETIMEDOUT;
+	if (to && !to->task)
+		goto out;
+
+	/*
+	 * We expect signal_pending(current), but we might be the
+	 * victim of a spurious wakeup as well.
+	 */
+	if (!signal_pending(current))
+		goto retry;
+
+	ret = -ERESTARTSYS;
+	if (!abs_time)
+		goto out;
+
+	restart = &current->restart_block;
+	restart->futex.uaddr = uaddr;
+	restart->futex.val = val;
+	restart->futex.time = *abs_time;
+	restart->futex.bitset = bitset;
+	restart->futex.flags = flags | FLAGS_HAS_TIMEOUT;
+
+	ret = set_restart_fn(restart, futex_wait_restart);
+
+out:
+	if (to) {
+		hrtimer_cancel(&to->timer);
+		destroy_hrtimer_on_stack(&to->timer);
+	}
+	return ret;
+}
+
+
+static long futex_wait_restart(struct restart_block *restart)
+{
+	u32 __user *uaddr = restart->futex.uaddr;
+	ktime_t t, *tp = NULL;
+
+	if (restart->futex.flags & FLAGS_HAS_TIMEOUT) {
+		t = restart->futex.time;
+		tp = &t;
+	}
+	restart->fn = do_no_restart_syscall;
+
+	return (long)futex_wait(uaddr, restart->futex.flags,
+				restart->futex.val, tp, restart->futex.bitset);
+}
+
+
+/*
+ * Userspace tried a 0 -> TID atomic transition of the futex value
+ * and failed. The kernel side here does the whole locking operation:
+ * if there are waiters then it will block as a consequence of relying
+ * on rt-mutexes, it does PI, etc. (Due to races the kernel might see
+ * a 0 value of the futex too.).
+ *
+ * Also serves as futex trylock_pi()'ing, and due semantics.
+ */
+static int futex_lock_pi(u32 __user *uaddr, unsigned int flags,
+			 ktime_t *time, int trylock)
+{
+	struct hrtimer_sleeper timeout, *to;
+	struct task_struct *exiting = NULL;
+	struct rt_mutex_waiter rt_waiter;
+	struct futex_hash_bucket *hb;
+	struct futex_q q = futex_q_init;
+	int res, ret;
+
+	if (!IS_ENABLED(CONFIG_FUTEX_PI))
+		return -ENOSYS;
+
+	if (refill_pi_state_cache())
+		return -ENOMEM;
+
+	to = futex_setup_timer(time, &timeout, flags, 0);
+
+retry:
+	ret = get_futex_key(uaddr, flags & FLAGS_SHARED, &q.key, FUTEX_WRITE);
+	if (unlikely(ret != 0))
+		goto out;
+
+retry_private:
+	hb = queue_lock(&q);
+
+	ret = futex_lock_pi_atomic(uaddr, hb, &q.key, &q.pi_state, current,
+				   &exiting, 0);
+	if (unlikely(ret)) {
+		/*
+		 * Atomic work succeeded and we got the lock,
+		 * or failed. Either way, we do _not_ block.
+		 */
+		switch (ret) {
+		case 1:
+			/* We got the lock. */
+			ret = 0;
+			goto out_unlock_put_key;
+		case -EFAULT:
+			goto uaddr_faulted;
+		case -EBUSY:
+		case -EAGAIN:
+			/*
+			 * Two reasons for this:
+			 * - EBUSY: Task is exiting and we just wait for the
+			 *   exit to complete.
+			 * - EAGAIN: The user space value changed.
+			 */
+			queue_unlock(hb);
+			/*
+			 * Handle the case where the owner is in the middle of
+			 * exiting. Wait for the exit to complete otherwise
+			 * this task might loop forever, aka. live lock.
+			 */
+			wait_for_owner_exiting(ret, exiting);
+			cond_resched();
+			goto retry;
+		default:
+			goto out_unlock_put_key;
+		}
+	}
+
+	WARN_ON(!q.pi_state);
+
+	/*
+	 * Only actually queue now that the atomic ops are done:
+	 */
+	__queue_me(&q, hb);
+
+	if (trylock) {
+		ret = rt_mutex_futex_trylock(&q.pi_state->pi_mutex);
+		/* Fixup the trylock return value: */
+		ret = ret ? 0 : -EWOULDBLOCK;
+		goto no_block;
+	}
+
+	rt_mutex_init_waiter(&rt_waiter);
+
+	/*
+	 * On PREEMPT_RT_FULL, when hb->lock becomes an rt_mutex, we must not
+	 * hold it while doing rt_mutex_start_proxy(), because then it will
+	 * include hb->lock in the blocking chain, even through we'll not in
+	 * fact hold it while blocking. This will lead it to report -EDEADLK
+	 * and BUG when futex_unlock_pi() interleaves with this.
+	 *
+	 * Therefore acquire wait_lock while holding hb->lock, but drop the
+	 * latter before calling __rt_mutex_start_proxy_lock(). This
+	 * interleaves with futex_unlock_pi() -- which does a similar lock
+	 * handoff -- such that the latter can observe the futex_q::pi_state
+	 * before __rt_mutex_start_proxy_lock() is done.
+	 */
+	raw_spin_lock_irq(&q.pi_state->pi_mutex.wait_lock);
+	spin_unlock(q.lock_ptr);
+	/*
+	 * __rt_mutex_start_proxy_lock() unconditionally enqueues the @rt_waiter
+	 * such that futex_unlock_pi() is guaranteed to observe the waiter when
+	 * it sees the futex_q::pi_state.
+	 */
+	ret = __rt_mutex_start_proxy_lock(&q.pi_state->pi_mutex, &rt_waiter, current);
+	raw_spin_unlock_irq(&q.pi_state->pi_mutex.wait_lock);
+
+	if (ret) {
+		if (ret == 1)
+			ret = 0;
+		goto cleanup;
+	}
+
+	if (unlikely(to))
+		hrtimer_sleeper_start_expires(to, HRTIMER_MODE_ABS);
+
+	ret = rt_mutex_wait_proxy_lock(&q.pi_state->pi_mutex, to, &rt_waiter);
+
+cleanup:
+	spin_lock(q.lock_ptr);
+	/*
+	 * If we failed to acquire the lock (deadlock/signal/timeout), we must
+	 * first acquire the hb->lock before removing the lock from the
+	 * rt_mutex waitqueue, such that we can keep the hb and rt_mutex wait
+	 * lists consistent.
+	 *
+	 * In particular; it is important that futex_unlock_pi() can not
+	 * observe this inconsistency.
+	 */
+	if (ret && !rt_mutex_cleanup_proxy_lock(&q.pi_state->pi_mutex, &rt_waiter))
+		ret = 0;
+
+no_block:
+	/*
+	 * Fixup the pi_state owner and possibly acquire the lock if we
+	 * haven't already.
+	 */
+	res = fixup_owner(uaddr, &q, !ret);
+	/*
+	 * If fixup_owner() returned an error, propagate that.  If it acquired
+	 * the lock, clear our -ETIMEDOUT or -EINTR.
+	 */
+	if (res)
+		ret = (res < 0) ? res : 0;
+
+	unqueue_me_pi(&q);
+	spin_unlock(q.lock_ptr);
+	goto out;
+
+out_unlock_put_key:
+	queue_unlock(hb);
+
+out:
+	if (to) {
+		hrtimer_cancel(&to->timer);
+		destroy_hrtimer_on_stack(&to->timer);
+	}
+	return ret != -EINTR ? ret : -ERESTARTNOINTR;
+
+uaddr_faulted:
+	queue_unlock(hb);
+
+	ret = fault_in_user_writeable(uaddr);
+	if (ret)
+		goto out;
+
+	if (!(flags & FLAGS_SHARED))
+		goto retry_private;
+
+	goto retry;
+}
+
+/*
+ * Userspace attempted a TID -> 0 atomic transition, and failed.
+ * This is the in-kernel slowpath: we look up the PI state (if any),
+ * and do the rt-mutex unlock.
+ */
+static int futex_unlock_pi(u32 __user *uaddr, unsigned int flags)
+{
+	u32 curval, uval, vpid = task_pid_vnr(current);
+	union futex_key key = FUTEX_KEY_INIT;
+	struct futex_hash_bucket *hb;
+	struct futex_q *top_waiter;
+	int ret;
+
+	if (!IS_ENABLED(CONFIG_FUTEX_PI))
+		return -ENOSYS;
+
+retry:
+	if (get_user(uval, uaddr))
+		return -EFAULT;
+	/*
+	 * We release only a lock we actually own:
+	 */
+	if ((uval & FUTEX_TID_MASK) != vpid)
+		return -EPERM;
+
+	ret = get_futex_key(uaddr, flags & FLAGS_SHARED, &key, FUTEX_WRITE);
+	if (ret)
+		return ret;
+
+	hb = hash_futex(&key);
+	spin_lock(&hb->lock);
+
+	/*
+	 * Check waiters first. We do not trust user space values at
+	 * all and we at least want to know if user space fiddled
+	 * with the futex value instead of blindly unlocking.
+	 */
+	top_waiter = futex_top_waiter(hb, &key);
+	if (top_waiter) {
+		struct futex_pi_state *pi_state = top_waiter->pi_state;
+
+		ret = -EINVAL;
+		if (!pi_state)
+			goto out_unlock;
+
+		/*
+		 * If current does not own the pi_state then the futex is
+		 * inconsistent and user space fiddled with the futex value.
+		 */
+		if (pi_state->owner != current)
+			goto out_unlock;
+
+		get_pi_state(pi_state);
+		/*
+		 * By taking wait_lock while still holding hb->lock, we ensure
+		 * there is no point where we hold neither; and therefore
+		 * wake_futex_pi() must observe a state consistent with what we
+		 * observed.
+		 *
+		 * In particular; this forces __rt_mutex_start_proxy() to
+		 * complete such that we're guaranteed to observe the
+		 * rt_waiter. Also see the WARN in wake_futex_pi().
+		 */
+		raw_spin_lock_irq(&pi_state->pi_mutex.wait_lock);
+		spin_unlock(&hb->lock);
+
+		/* drops pi_state->pi_mutex.wait_lock */
+		ret = wake_futex_pi(uaddr, uval, pi_state);
+
+		put_pi_state(pi_state);
+
+		/*
+		 * Success, we're done! No tricky corner cases.
+		 */
+		if (!ret)
+			return ret;
+		/*
+		 * The atomic access to the futex value generated a
+		 * pagefault, so retry the user-access and the wakeup:
+		 */
+		if (ret == -EFAULT)
+			goto pi_faulted;
+		/*
+		 * A unconditional UNLOCK_PI op raced against a waiter
+		 * setting the FUTEX_WAITERS bit. Try again.
+		 */
+		if (ret == -EAGAIN)
+			goto pi_retry;
+		/*
+		 * wake_futex_pi has detected invalid state. Tell user
+		 * space.
+		 */
+		return ret;
+	}
+
+	/*
+	 * We have no kernel internal state, i.e. no waiters in the
+	 * kernel. Waiters which are about to queue themselves are stuck
+	 * on hb->lock. So we can safely ignore them. We do neither
+	 * preserve the WAITERS bit not the OWNER_DIED one. We are the
+	 * owner.
+	 */
+	if ((ret = cmpxchg_futex_value_locked(&curval, uaddr, uval, 0))) {
+		spin_unlock(&hb->lock);
+		switch (ret) {
+		case -EFAULT:
+			goto pi_faulted;
+
+		case -EAGAIN:
+			goto pi_retry;
+
+		default:
+			WARN_ON_ONCE(1);
+			return ret;
+		}
+	}
+
+	/*
+	 * If uval has changed, let user space handle it.
+	 */
+	ret = (curval == uval) ? 0 : -EAGAIN;
+
+out_unlock:
+	spin_unlock(&hb->lock);
+	return ret;
+
+pi_retry:
+	cond_resched();
+	goto retry;
+
+pi_faulted:
+
+	ret = fault_in_user_writeable(uaddr);
+	if (!ret)
+		goto retry;
+
+	return ret;
+}
+
+/**
+ * handle_early_requeue_pi_wakeup() - Handle early wakeup on the initial futex
+ * @hb:		the hash_bucket futex_q was original enqueued on
+ * @q:		the futex_q woken while waiting to be requeued
+ * @timeout:	the timeout associated with the wait (NULL if none)
+ *
+ * Determine the cause for the early wakeup.
+ *
+ * Return:
+ *  -EWOULDBLOCK or -ETIMEDOUT or -ERESTARTNOINTR
+ */
+static inline
+int handle_early_requeue_pi_wakeup(struct futex_hash_bucket *hb,
+				   struct futex_q *q,
+				   struct hrtimer_sleeper *timeout)
+{
+	int ret;
+
+	/*
+	 * With the hb lock held, we avoid races while we process the wakeup.
+	 * We only need to hold hb (and not hb2) to ensure atomicity as the
+	 * wakeup code can't change q.key from uaddr to uaddr2 if we hold hb.
+	 * It can't be requeued from uaddr2 to something else since we don't
+	 * support a PI aware source futex for requeue.
+	 */
+	WARN_ON_ONCE(&hb->lock != q->lock_ptr);
+
+	/*
+	 * We were woken prior to requeue by a timeout or a signal.
+	 * Unqueue the futex_q and determine which it was.
+	 */
+	plist_del(&q->list, &hb->chain);
+	hb_waiters_dec(hb);
+
+	/* Handle spurious wakeups gracefully */
+	ret = -EWOULDBLOCK;
+	if (timeout && !timeout->task)
+		ret = -ETIMEDOUT;
+	else if (signal_pending(current))
+		ret = -ERESTARTNOINTR;
+	return ret;
+}
+
+/**
+ * futex_wait_requeue_pi() - Wait on uaddr and take uaddr2
+ * @uaddr:	the futex we initially wait on (non-pi)
+ * @flags:	futex flags (FLAGS_SHARED, FLAGS_CLOCKRT, etc.), they must be
+ *		the same type, no requeueing from private to shared, etc.
+ * @val:	the expected value of uaddr
+ * @abs_time:	absolute timeout
+ * @bitset:	32 bit wakeup bitset set by userspace, defaults to all
+ * @uaddr2:	the pi futex we will take prior to returning to user-space
+ *
+ * The caller will wait on uaddr and will be requeued by futex_requeue() to
+ * uaddr2 which must be PI aware and unique from uaddr.  Normal wakeup will wake
+ * on uaddr2 and complete the acquisition of the rt_mutex prior to returning to
+ * userspace.  This ensures the rt_mutex maintains an owner when it has waiters;
+ * without one, the pi logic would not know which task to boost/deboost, if
+ * there was a need to.
+ *
+ * We call schedule in futex_wait_queue_me() when we enqueue and return there
+ * via the following--
+ * 1) wakeup on uaddr2 after an atomic lock acquisition by futex_requeue()
+ * 2) wakeup on uaddr2 after a requeue
+ * 3) signal
+ * 4) timeout
+ *
+ * If 3, cleanup and return -ERESTARTNOINTR.
+ *
+ * If 2, we may then block on trying to take the rt_mutex and return via:
+ * 5) successful lock
+ * 6) signal
+ * 7) timeout
+ * 8) other lock acquisition failure
+ *
+ * If 6, return -EWOULDBLOCK (restarting the syscall would do the same).
+ *
+ * If 4 or 7, we cleanup and return with -ETIMEDOUT.
+ *
+ * Return:
+ *  -  0 - On success;
+ *  - <0 - On error
+ */
+static int futex_wait_requeue_pi(u32 __user *uaddr, unsigned int flags,
+				 u32 val, ktime_t *abs_time, u32 bitset,
+				 u32 __user *uaddr2)
+{
+	struct hrtimer_sleeper timeout, *to;
+	struct rt_mutex_waiter rt_waiter;
+	struct futex_hash_bucket *hb;
+	union futex_key key2 = FUTEX_KEY_INIT;
+	struct futex_q q = futex_q_init;
+	struct rt_mutex_base *pi_mutex;
+	int res, ret;
+
+	if (!IS_ENABLED(CONFIG_FUTEX_PI))
+		return -ENOSYS;
+
+	if (uaddr == uaddr2)
+		return -EINVAL;
+
+	if (!bitset)
+		return -EINVAL;
+
+	to = futex_setup_timer(abs_time, &timeout, flags,
+			       current->timer_slack_ns);
+
+	/*
+	 * The waiter is allocated on our stack, manipulated by the requeue
+	 * code while we sleep on uaddr.
+	 */
+	rt_mutex_init_waiter(&rt_waiter);
+
+	ret = get_futex_key(uaddr2, flags & FLAGS_SHARED, &key2, FUTEX_WRITE);
+	if (unlikely(ret != 0))
+		goto out;
+
+	q.bitset = bitset;
+	q.rt_waiter = &rt_waiter;
+	q.requeue_pi_key = &key2;
+
+	/*
+	 * Prepare to wait on uaddr. On success, it holds hb->lock and q
+	 * is initialized.
+	 */
+	ret = futex_wait_setup(uaddr, val, flags, &q, &hb);
+	if (ret)
+		goto out;
+
+	/*
+	 * The check above which compares uaddrs is not sufficient for
+	 * shared futexes. We need to compare the keys:
+	 */
+	if (match_futex(&q.key, &key2)) {
+		queue_unlock(hb);
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* Queue the futex_q, drop the hb lock, wait for wakeup. */
+	futex_wait_queue_me(hb, &q, to);
+
+	switch (futex_requeue_pi_wakeup_sync(&q)) {
+	case Q_REQUEUE_PI_IGNORE:
+		/* The waiter is still on uaddr1 */
+		spin_lock(&hb->lock);
+		ret = handle_early_requeue_pi_wakeup(hb, &q, to);
+		spin_unlock(&hb->lock);
+		break;
+
+	case Q_REQUEUE_PI_LOCKED:
+		/* The requeue acquired the lock */
+		if (q.pi_state && (q.pi_state->owner != current)) {
+			spin_lock(q.lock_ptr);
+			ret = fixup_owner(uaddr2, &q, true);
+			/*
+			 * Drop the reference to the pi state which the
+			 * requeue_pi() code acquired for us.
+			 */
+			put_pi_state(q.pi_state);
+			spin_unlock(q.lock_ptr);
+			/*
+			 * Adjust the return value. It's either -EFAULT or
+			 * success (1) but the caller expects 0 for success.
+			 */
+			ret = ret < 0 ? ret : 0;
+		}
+		break;
+
+	case Q_REQUEUE_PI_DONE:
+		/* Requeue completed. Current is 'pi_blocked_on' the rtmutex */
+		pi_mutex = &q.pi_state->pi_mutex;
+		ret = rt_mutex_wait_proxy_lock(pi_mutex, to, &rt_waiter);
+
+		/* Current is not longer pi_blocked_on */
+		spin_lock(q.lock_ptr);
+		if (ret && !rt_mutex_cleanup_proxy_lock(pi_mutex, &rt_waiter))
+			ret = 0;
+
+		debug_rt_mutex_free_waiter(&rt_waiter);
+		/*
+		 * Fixup the pi_state owner and possibly acquire the lock if we
+		 * haven't already.
+		 */
+		res = fixup_owner(uaddr2, &q, !ret);
+		/*
+		 * If fixup_owner() returned an error, propagate that.  If it
+		 * acquired the lock, clear -ETIMEDOUT or -EINTR.
+		 */
+		if (res)
+			ret = (res < 0) ? res : 0;
+
+		unqueue_me_pi(&q);
+		spin_unlock(q.lock_ptr);
+
+		if (ret == -EINTR) {
+			/*
+			 * We've already been requeued, but cannot restart
+			 * by calling futex_lock_pi() directly. We could
+			 * restart this syscall, but it would detect that
+			 * the user space "val" changed and return
+			 * -EWOULDBLOCK.  Save the overhead of the restart
+			 * and return -EWOULDBLOCK directly.
+			 */
+			ret = -EWOULDBLOCK;
+		}
+		break;
+	default:
+		BUG();
+	}
+
+out:
+	if (to) {
+		hrtimer_cancel(&to->timer);
+		destroy_hrtimer_on_stack(&to->timer);
+	}
+	return ret;
+}
+
+/*
+ * Support for robust futexes: the kernel cleans up held futexes at
+ * thread exit time.
+ *
+ * Implementation: user-space maintains a per-thread list of locks it
+ * is holding. Upon do_exit(), the kernel carefully walks this list,
+ * and marks all locks that are owned by this thread with the
+ * FUTEX_OWNER_DIED bit, and wakes up a waiter (if any). The list is
+ * always manipulated with the lock held, so the list is private and
+ * per-thread. Userspace also maintains a per-thread 'list_op_pending'
+ * field, to allow the kernel to clean up if the thread dies after
+ * acquiring the lock, but just before it could have added itself to
+ * the list. There can only be one such pending lock.
+ */
+
+/**
+ * sys_set_robust_list() - Set the robust-futex list head of a task
+ * @head:	pointer to the list-head
+ * @len:	length of the list-head, as userspace expects
+ */
+SYSCALL_DEFINE2(set_robust_list, struct robust_list_head __user *, head,
+		size_t, len)
+{
+	if (!futex_cmpxchg_enabled)
+		return -ENOSYS;
+	/*
+	 * The kernel knows only one size for now:
+	 */
+	if (unlikely(len != sizeof(*head)))
+		return -EINVAL;
+
+	current->robust_list = head;
+
+	return 0;
+}
+
+/**
+ * sys_get_robust_list() - Get the robust-futex list head of a task
+ * @pid:	pid of the process [zero for current task]
+ * @head_ptr:	pointer to a list-head pointer, the kernel fills it in
+ * @len_ptr:	pointer to a length field, the kernel fills in the header size
+ */
+SYSCALL_DEFINE3(get_robust_list, int, pid,
+		struct robust_list_head __user * __user *, head_ptr,
+		size_t __user *, len_ptr)
+{
+	struct robust_list_head __user *head;
+	unsigned long ret;
+	struct task_struct *p;
+
+	if (!futex_cmpxchg_enabled)
+		return -ENOSYS;
+
+	rcu_read_lock();
+
+	ret = -ESRCH;
+	if (!pid)
+		p = current;
+	else {
+		p = find_task_by_vpid(pid);
+		if (!p)
+			goto err_unlock;
+	}
+
+	ret = -EPERM;
+	if (!ptrace_may_access(p, PTRACE_MODE_READ_REALCREDS))
+		goto err_unlock;
+
+	head = p->robust_list;
+	rcu_read_unlock();
+
+	if (put_user(sizeof(*head), len_ptr))
+		return -EFAULT;
+	return put_user(head, head_ptr);
+
+err_unlock:
+	rcu_read_unlock();
+
+	return ret;
+}
+
+/* Constants for the pending_op argument of handle_futex_death */
+#define HANDLE_DEATH_PENDING	true
+#define HANDLE_DEATH_LIST	false
+
+/*
+ * Process a futex-list entry, check whether it's owned by the
+ * dying task, and do notification if so:
+ */
+static int handle_futex_death(u32 __user *uaddr, struct task_struct *curr,
+			      bool pi, bool pending_op)
+{
+	u32 uval, nval, mval;
+	pid_t owner;
+	int err;
+
+	/* Futex address must be 32bit aligned */
+	if ((((unsigned long)uaddr) % sizeof(*uaddr)) != 0)
+		return -1;
+
+retry:
+	if (get_user(uval, uaddr))
+		return -1;
+
+	/*
+	 * Special case for regular (non PI) futexes. The unlock path in
+	 * user space has two race scenarios:
+	 *
+	 * 1. The unlock path releases the user space futex value and
+	 *    before it can execute the futex() syscall to wake up
+	 *    waiters it is killed.
+	 *
+	 * 2. A woken up waiter is killed before it can acquire the
+	 *    futex in user space.
+	 *
+	 * In the second case, the wake up notification could be generated
+	 * by the unlock path in user space after setting the futex value
+	 * to zero or by the kernel after setting the OWNER_DIED bit below.
+	 *
+	 * In both cases the TID validation below prevents a wakeup of
+	 * potential waiters which can cause these waiters to block
+	 * forever.
+	 *
+	 * In both cases the following conditions are met:
+	 *
+	 *	1) task->robust_list->list_op_pending != NULL
+	 *	   @pending_op == true
+	 *	2) The owner part of user space futex value == 0
+	 *	3) Regular futex: @pi == false
+	 *
+	 * If these conditions are met, it is safe to attempt waking up a
+	 * potential waiter without touching the user space futex value and
+	 * trying to set the OWNER_DIED bit. If the futex value is zero,
+	 * the rest of the user space mutex state is consistent, so a woken
+	 * waiter will just take over the uncontended futex. Setting the
+	 * OWNER_DIED bit would create inconsistent state and malfunction
+	 * of the user space owner died handling. Otherwise, the OWNER_DIED
+	 * bit is already set, and the woken waiter is expected to deal with
+	 * this.
+	 */
+	owner = uval & FUTEX_TID_MASK;
+
+	if (pending_op && !pi && !owner) {
+		futex_wake(uaddr, 1, 1, FUTEX_BITSET_MATCH_ANY);
+		return 0;
+	}
+
+	if (owner != task_pid_vnr(curr))
+		return 0;
+
+	/*
+	 * Ok, this dying thread is truly holding a futex
+	 * of interest. Set the OWNER_DIED bit atomically
+	 * via cmpxchg, and if the value had FUTEX_WAITERS
+	 * set, wake up a waiter (if any). (We have to do a
+	 * futex_wake() even if OWNER_DIED is already set -
+	 * to handle the rare but possible case of recursive
+	 * thread-death.) The rest of the cleanup is done in
+	 * userspace.
+	 */
+	mval = (uval & FUTEX_WAITERS) | FUTEX_OWNER_DIED;
+
+	/*
+	 * We are not holding a lock here, but we want to have
+	 * the pagefault_disable/enable() protection because
+	 * we want to handle the fault gracefully. If the
+	 * access fails we try to fault in the futex with R/W
+	 * verification via get_user_pages. get_user() above
+	 * does not guarantee R/W access. If that fails we
+	 * give up and leave the futex locked.
+	 */
+	if ((err = cmpxchg_futex_value_locked(&nval, uaddr, uval, mval))) {
+		switch (err) {
+		case -EFAULT:
+			if (fault_in_user_writeable(uaddr))
+				return -1;
+			goto retry;
+
+		case -EAGAIN:
+			cond_resched();
+			goto retry;
+
+		default:
+			WARN_ON_ONCE(1);
+			return err;
+		}
+	}
+
+	if (nval != uval)
+		goto retry;
+
+	/*
+	 * Wake robust non-PI futexes here. The wakeup of
+	 * PI futexes happens in exit_pi_state():
+	 */
+	if (!pi && (uval & FUTEX_WAITERS))
+		futex_wake(uaddr, 1, 1, FUTEX_BITSET_MATCH_ANY);
+
+	return 0;
+}
+
+/*
+ * Fetch a robust-list pointer. Bit 0 signals PI futexes:
+ */
+static inline int fetch_robust_entry(struct robust_list __user **entry,
+				     struct robust_list __user * __user *head,
+				     unsigned int *pi)
+{
+	unsigned long uentry;
+
+	if (get_user(uentry, (unsigned long __user *)head))
+		return -EFAULT;
+
+	*entry = (void __user *)(uentry & ~1UL);
+	*pi = uentry & 1;
+
+	return 0;
+}
+
+/*
+ * Walk curr->robust_list (very carefully, it's a userspace list!)
+ * and mark any locks found there dead, and notify any waiters.
+ *
+ * We silently return on any sign of list-walking problem.
+ */
+static void exit_robust_list(struct task_struct *curr)
+{
+	struct robust_list_head __user *head = curr->robust_list;
+	struct robust_list __user *entry, *next_entry, *pending;
+	unsigned int limit = ROBUST_LIST_LIMIT, pi, pip;
+	unsigned int next_pi;
+	unsigned long futex_offset;
+	int rc;
+
+	if (!futex_cmpxchg_enabled)
+		return;
+
+	/*
+	 * Fetch the list head (which was registered earlier, via
+	 * sys_set_robust_list()):
+	 */
+	if (fetch_robust_entry(&entry, &head->list.next, &pi))
+		return;
+	/*
+	 * Fetch the relative futex offset:
+	 */
+	if (get_user(futex_offset, &head->futex_offset))
+		return;
+	/*
+	 * Fetch any possibly pending lock-add first, and handle it
+	 * if it exists:
+	 */
+	if (fetch_robust_entry(&pending, &head->list_op_pending, &pip))
+		return;
+
+	next_entry = NULL;	/* avoid warning with gcc */
+	while (entry != &head->list) {
+		/*
+		 * Fetch the next entry in the list before calling
+		 * handle_futex_death:
+		 */
+		rc = fetch_robust_entry(&next_entry, &entry->next, &next_pi);
+		/*
+		 * A pending lock might already be on the list, so
+		 * don't process it twice:
+		 */
+		if (entry != pending) {
+			if (handle_futex_death((void __user *)entry + futex_offset,
+						curr, pi, HANDLE_DEATH_LIST))
+				return;
+		}
+		if (rc)
+			return;
+		entry = next_entry;
+		pi = next_pi;
+		/*
+		 * Avoid excessively long or circular lists:
+		 */
+		if (!--limit)
+			break;
+
+		cond_resched();
+	}
+
+	if (pending) {
+		handle_futex_death((void __user *)pending + futex_offset,
+				   curr, pip, HANDLE_DEATH_PENDING);
+	}
+}
+
+static void futex_cleanup(struct task_struct *tsk)
+{
+	if (unlikely(tsk->robust_list)) {
+		exit_robust_list(tsk);
+		tsk->robust_list = NULL;
+	}
+
+#ifdef CONFIG_COMPAT
+	if (unlikely(tsk->compat_robust_list)) {
+		compat_exit_robust_list(tsk);
+		tsk->compat_robust_list = NULL;
+	}
+#endif
+
+	if (unlikely(!list_empty(&tsk->pi_state_list)))
+		exit_pi_state_list(tsk);
+}
+
+/**
+ * futex_exit_recursive - Set the tasks futex state to FUTEX_STATE_DEAD
+ * @tsk:	task to set the state on
+ *
+ * Set the futex exit state of the task lockless. The futex waiter code
+ * observes that state when a task is exiting and loops until the task has
+ * actually finished the futex cleanup. The worst case for this is that the
+ * waiter runs through the wait loop until the state becomes visible.
+ *
+ * This is called from the recursive fault handling path in do_exit().
+ *
+ * This is best effort. Either the futex exit code has run already or
+ * not. If the OWNER_DIED bit has been set on the futex then the waiter can
+ * take it over. If not, the problem is pushed back to user space. If the
+ * futex exit code did not run yet, then an already queued waiter might
+ * block forever, but there is nothing which can be done about that.
+ */
+void futex_exit_recursive(struct task_struct *tsk)
+{
+	/* If the state is FUTEX_STATE_EXITING then futex_exit_mutex is held */
+	if (tsk->futex_state == FUTEX_STATE_EXITING)
+		mutex_unlock(&tsk->futex_exit_mutex);
+	tsk->futex_state = FUTEX_STATE_DEAD;
+}
+
+static void futex_cleanup_begin(struct task_struct *tsk)
+{
+	/*
+	 * Prevent various race issues against a concurrent incoming waiter
+	 * including live locks by forcing the waiter to block on
+	 * tsk->futex_exit_mutex when it observes FUTEX_STATE_EXITING in
+	 * attach_to_pi_owner().
+	 */
+	mutex_lock(&tsk->futex_exit_mutex);
+
+	/*
+	 * Switch the state to FUTEX_STATE_EXITING under tsk->pi_lock.
+	 *
+	 * This ensures that all subsequent checks of tsk->futex_state in
+	 * attach_to_pi_owner() must observe FUTEX_STATE_EXITING with
+	 * tsk->pi_lock held.
+	 *
+	 * It guarantees also that a pi_state which was queued right before
+	 * the state change under tsk->pi_lock by a concurrent waiter must
+	 * be observed in exit_pi_state_list().
+	 */
+	raw_spin_lock_irq(&tsk->pi_lock);
+	tsk->futex_state = FUTEX_STATE_EXITING;
+	raw_spin_unlock_irq(&tsk->pi_lock);
+}
+
+static void futex_cleanup_end(struct task_struct *tsk, int state)
+{
+	/*
+	 * Lockless store. The only side effect is that an observer might
+	 * take another loop until it becomes visible.
+	 */
+	tsk->futex_state = state;
+	/*
+	 * Drop the exit protection. This unblocks waiters which observed
+	 * FUTEX_STATE_EXITING to reevaluate the state.
+	 */
+	mutex_unlock(&tsk->futex_exit_mutex);
+}
+
+void futex_exec_release(struct task_struct *tsk)
+{
+	/*
+	 * The state handling is done for consistency, but in the case of
+	 * exec() there is no way to prevent further damage as the PID stays
+	 * the same. But for the unlikely and arguably buggy case that a
+	 * futex is held on exec(), this provides at least as much state
+	 * consistency protection which is possible.
+	 */
+	futex_cleanup_begin(tsk);
+	futex_cleanup(tsk);
+	/*
+	 * Reset the state to FUTEX_STATE_OK. The task is alive and about
+	 * exec a new binary.
+	 */
+	futex_cleanup_end(tsk, FUTEX_STATE_OK);
+}
+
+void futex_exit_release(struct task_struct *tsk)
+{
+	futex_cleanup_begin(tsk);
+	futex_cleanup(tsk);
+	futex_cleanup_end(tsk, FUTEX_STATE_DEAD);
+}
+
+long do_futex(u32 __user *uaddr, int op, u32 val, ktime_t *timeout,
+		u32 __user *uaddr2, u32 val2, u32 val3)
+{
+	int cmd = op & FUTEX_CMD_MASK;
+	unsigned int flags = 0;
+
+	if (!(op & FUTEX_PRIVATE_FLAG))
+		flags |= FLAGS_SHARED;
+
+	if (op & FUTEX_CLOCK_REALTIME) {
+		flags |= FLAGS_CLOCKRT;
+		if (cmd != FUTEX_WAIT_BITSET && cmd != FUTEX_WAIT_REQUEUE_PI &&
+		    cmd != FUTEX_LOCK_PI2)
+			return -ENOSYS;
+	}
+
+	switch (cmd) {
+	case FUTEX_LOCK_PI:
+	case FUTEX_LOCK_PI2:
+	case FUTEX_UNLOCK_PI:
+	case FUTEX_TRYLOCK_PI:
+	case FUTEX_WAIT_REQUEUE_PI:
+	case FUTEX_CMP_REQUEUE_PI:
+		if (!futex_cmpxchg_enabled)
+			return -ENOSYS;
+	}
+
+	switch (cmd) {
+	case FUTEX_WAIT:
+		val3 = FUTEX_BITSET_MATCH_ANY;
+		fallthrough;
+	case FUTEX_WAIT_BITSET:
+		return futex_wait(uaddr, flags, val, timeout, val3);
+	case FUTEX_WAKE:
+		val3 = FUTEX_BITSET_MATCH_ANY;
+		fallthrough;
+	case FUTEX_WAKE_BITSET:
+		return futex_wake(uaddr, flags, val, val3);
+	case FUTEX_REQUEUE:
+		return futex_requeue(uaddr, flags, uaddr2, val, val2, NULL, 0);
+	case FUTEX_CMP_REQUEUE:
+		return futex_requeue(uaddr, flags, uaddr2, val, val2, &val3, 0);
+	case FUTEX_WAKE_OP:
+		return futex_wake_op(uaddr, flags, uaddr2, val, val2, val3);
+	case FUTEX_LOCK_PI:
+		flags |= FLAGS_CLOCKRT;
+		fallthrough;
+	case FUTEX_LOCK_PI2:
+		return futex_lock_pi(uaddr, flags, timeout, 0);
+	case FUTEX_UNLOCK_PI:
+		return futex_unlock_pi(uaddr, flags);
+	case FUTEX_TRYLOCK_PI:
+		return futex_lock_pi(uaddr, flags, NULL, 1);
+	case FUTEX_WAIT_REQUEUE_PI:
+		val3 = FUTEX_BITSET_MATCH_ANY;
+		return futex_wait_requeue_pi(uaddr, flags, val, timeout, val3,
+					     uaddr2);
+	case FUTEX_CMP_REQUEUE_PI:
+		return futex_requeue(uaddr, flags, uaddr2, val, val2, &val3, 1);
+	}
+	return -ENOSYS;
+}
+
+static __always_inline bool futex_cmd_has_timeout(u32 cmd)
+{
+	switch (cmd) {
+	case FUTEX_WAIT:
+	case FUTEX_LOCK_PI:
+	case FUTEX_LOCK_PI2:
+	case FUTEX_WAIT_BITSET:
+	case FUTEX_WAIT_REQUEUE_PI:
+		return true;
+	}
+	return false;
+}
+
+static __always_inline int
+futex_init_timeout(u32 cmd, u32 op, struct timespec64 *ts, ktime_t *t)
+{
+	if (!timespec64_valid(ts))
+		return -EINVAL;
+
+	*t = timespec64_to_ktime(*ts);
+	if (cmd == FUTEX_WAIT)
+		*t = ktime_add_safe(ktime_get(), *t);
+	else if (cmd != FUTEX_LOCK_PI && !(op & FUTEX_CLOCK_REALTIME))
+		*t = timens_ktime_to_host(CLOCK_MONOTONIC, *t);
+	return 0;
+}
+
+SYSCALL_DEFINE6(futex, u32 __user *, uaddr, int, op, u32, val,
+		const struct __kernel_timespec __user *, utime,
+		u32 __user *, uaddr2, u32, val3)
+{
+	int ret, cmd = op & FUTEX_CMD_MASK;
+	ktime_t t, *tp = NULL;
+	struct timespec64 ts;
+
+	if (utime && futex_cmd_has_timeout(cmd)) {
+		if (unlikely(should_fail_futex(!(op & FUTEX_PRIVATE_FLAG))))
+			return -EFAULT;
+		if (get_timespec64(&ts, utime))
+			return -EFAULT;
+		ret = futex_init_timeout(cmd, op, &ts, &t);
+		if (ret)
+			return ret;
+		tp = &t;
+	}
+
+	return do_futex(uaddr, op, val, tp, uaddr2, (unsigned long)utime, val3);
+}
+
+#ifdef CONFIG_COMPAT
+/*
+ * Fetch a robust-list pointer. Bit 0 signals PI futexes:
+ */
+static inline int
+compat_fetch_robust_entry(compat_uptr_t *uentry, struct robust_list __user **entry,
+		   compat_uptr_t __user *head, unsigned int *pi)
+{
+	if (get_user(*uentry, head))
+		return -EFAULT;
+
+	*entry = compat_ptr((*uentry) & ~1);
+	*pi = (unsigned int)(*uentry) & 1;
+
+	return 0;
+}
+
+static void __user *futex_uaddr(struct robust_list __user *entry,
+				compat_long_t futex_offset)
+{
+	compat_uptr_t base = ptr_to_compat(entry);
+	void __user *uaddr = compat_ptr(base + futex_offset);
+
+	return uaddr;
+}
+
+/*
+ * Walk curr->robust_list (very carefully, it's a userspace list!)
+ * and mark any locks found there dead, and notify any waiters.
+ *
+ * We silently return on any sign of list-walking problem.
+ */
+static void compat_exit_robust_list(struct task_struct *curr)
+{
+	struct compat_robust_list_head __user *head = curr->compat_robust_list;
+	struct robust_list __user *entry, *next_entry, *pending;
+	unsigned int limit = ROBUST_LIST_LIMIT, pi, pip;
+	unsigned int next_pi;
+	compat_uptr_t uentry, next_uentry, upending;
+	compat_long_t futex_offset;
+	int rc;
+
+	if (!futex_cmpxchg_enabled)
+		return;
+
+	/*
+	 * Fetch the list head (which was registered earlier, via
+	 * sys_set_robust_list()):
+	 */
+	if (compat_fetch_robust_entry(&uentry, &entry, &head->list.next, &pi))
+		return;
+	/*
+	 * Fetch the relative futex offset:
+	 */
+	if (get_user(futex_offset, &head->futex_offset))
+		return;
+	/*
+	 * Fetch any possibly pending lock-add first, and handle it
+	 * if it exists:
+	 */
+	if (compat_fetch_robust_entry(&upending, &pending,
+			       &head->list_op_pending, &pip))
+		return;
+
+	next_entry = NULL;	/* avoid warning with gcc */
+	while (entry != (struct robust_list __user *) &head->list) {
+		/*
+		 * Fetch the next entry in the list before calling
+		 * handle_futex_death:
+		 */
+		rc = compat_fetch_robust_entry(&next_uentry, &next_entry,
+			(compat_uptr_t __user *)&entry->next, &next_pi);
+		/*
+		 * A pending lock might already be on the list, so
+		 * dont process it twice:
+		 */
+		if (entry != pending) {
+			void __user *uaddr = futex_uaddr(entry, futex_offset);
+
+			if (handle_futex_death(uaddr, curr, pi,
+					       HANDLE_DEATH_LIST))
+				return;
+		}
+		if (rc)
+			return;
+		uentry = next_uentry;
+		entry = next_entry;
+		pi = next_pi;
+		/*
+		 * Avoid excessively long or circular lists:
+		 */
+		if (!--limit)
+			break;
+
+		cond_resched();
+	}
+	if (pending) {
+		void __user *uaddr = futex_uaddr(pending, futex_offset);
+
+		handle_futex_death(uaddr, curr, pip, HANDLE_DEATH_PENDING);
+	}
+}
+
+COMPAT_SYSCALL_DEFINE2(set_robust_list,
+		struct compat_robust_list_head __user *, head,
+		compat_size_t, len)
+{
+	if (!futex_cmpxchg_enabled)
+		return -ENOSYS;
+
+	if (unlikely(len != sizeof(*head)))
+		return -EINVAL;
+
+	current->compat_robust_list = head;
+
+	return 0;
+}
+
+COMPAT_SYSCALL_DEFINE3(get_robust_list, int, pid,
+			compat_uptr_t __user *, head_ptr,
+			compat_size_t __user *, len_ptr)
+{
+	struct compat_robust_list_head __user *head;
+	unsigned long ret;
+	struct task_struct *p;
+
+	if (!futex_cmpxchg_enabled)
+		return -ENOSYS;
+
+	rcu_read_lock();
+
+	ret = -ESRCH;
+	if (!pid)
+		p = current;
+	else {
+		p = find_task_by_vpid(pid);
+		if (!p)
+			goto err_unlock;
+	}
+
+	ret = -EPERM;
+	if (!ptrace_may_access(p, PTRACE_MODE_READ_REALCREDS))
+		goto err_unlock;
+
+	head = p->compat_robust_list;
+	rcu_read_unlock();
+
+	if (put_user(sizeof(*head), len_ptr))
+		return -EFAULT;
+	return put_user(ptr_to_compat(head), head_ptr);
+
+err_unlock:
+	rcu_read_unlock();
+
+	return ret;
+}
+#endif /* CONFIG_COMPAT */
+
+#ifdef CONFIG_COMPAT_32BIT_TIME
+SYSCALL_DEFINE6(futex_time32, u32 __user *, uaddr, int, op, u32, val,
+		const struct old_timespec32 __user *, utime, u32 __user *, uaddr2,
+		u32, val3)
+{
+	int ret, cmd = op & FUTEX_CMD_MASK;
+	ktime_t t, *tp = NULL;
+	struct timespec64 ts;
+
+	if (utime && futex_cmd_has_timeout(cmd)) {
+		if (get_old_timespec32(&ts, utime))
+			return -EFAULT;
+		ret = futex_init_timeout(cmd, op, &ts, &t);
+		if (ret)
+			return ret;
+		tp = &t;
+	}
+
+	return do_futex(uaddr, op, val, tp, uaddr2, (unsigned long)utime, val3);
+}
+#endif /* CONFIG_COMPAT_32BIT_TIME */
+
+static void __init futex_detect_cmpxchg(void)
+{
+#ifndef CONFIG_HAVE_FUTEX_CMPXCHG
+	u32 curval;
+
+	/*
+	 * This will fail and we want it. Some arch implementations do
+	 * runtime detection of the futex_atomic_cmpxchg_inatomic()
+	 * functionality. We want to know that before we call in any
+	 * of the complex code paths. Also we want to prevent
+	 * registration of robust lists in that case. NULL is
+	 * guaranteed to fault and we get -EFAULT on functional
+	 * implementation, the non-functional ones will return
+	 * -ENOSYS.
+	 */
+	if (cmpxchg_futex_value_locked(&curval, NULL, 0, 0) == -EFAULT)
+		futex_cmpxchg_enabled = 1;
+#endif
+}
+
+static int __init futex_init(void)
+{
+	unsigned int futex_shift;
+	unsigned long i;
+
+#if CONFIG_BASE_SMALL
+	futex_hashsize = 16;
+#else
+	futex_hashsize = roundup_pow_of_two(256 * num_possible_cpus());
+#endif
+
+	futex_queues = alloc_large_system_hash("futex", sizeof(*futex_queues),
+					       futex_hashsize, 0,
+					       futex_hashsize < 256 ? HASH_SMALL : 0,
+					       &futex_shift, NULL,
+					       futex_hashsize, futex_hashsize);
+	futex_hashsize = 1UL << futex_shift;
+
+	futex_detect_cmpxchg();
+
+	for (i = 0; i < futex_hashsize; i++) {
+		atomic_set(&futex_queues[i].waiters, 0);
+		plist_head_init(&futex_queues[i].chain);
+		spin_lock_init(&futex_queues[i].lock);
+	}
+
+	return 0;
+}
+core_initcall(futex_init);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/gcov/clang.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/gcov/clang.c
@@ -280,6 +280,8 @@
 
 		for (i = 0; i < sfn_ptr->num_counters; i++)
 			dfn_ptr->counters[i] += sfn_ptr->counters[i];
+
+		sfn_ptr = list_next_entry(sfn_ptr, head);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/gcov/gcc_4_7.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/gcov/gcc_4_7.c
@@ -18,7 +18,9 @@
 #include <linux/mm.h>
 #include "gcov.h"
 
-#if (__GNUC__ >= 10)
+#if (__GNUC__ >= 14)
+#define GCOV_COUNTERS			9
+#elif (__GNUC__ >= 10)
 #define GCOV_COUNTERS			8
 #elif (__GNUC__ >= 7)
 #define GCOV_COUNTERS			9
@@ -30,6 +32,13 @@
 
 #define GCOV_TAG_FUNCTION_LENGTH	3
 
+/* Since GCC 12.1 sizes are in BYTES and not in WORDS (4B). */
+#if (__GNUC__ >= 12)
+#define GCOV_UNIT_SIZE				4
+#else
+#define GCOV_UNIT_SIZE				1
+#endif
+
 static struct gcov_info *gcov_info_head;
 
 /**
@@ -75,6 +84,7 @@
  * @version: gcov version magic indicating the gcc version used for compilation
  * @next: list head for a singly-linked list
  * @stamp: uniquifying time stamp
+ * @checksum: unique object checksum
  * @filename: name of the associated gcov data file
  * @merge: merge functions (null for unused counter type)
  * @n_functions: number of instrumented functions
@@ -87,6 +97,10 @@
 	unsigned int version;
 	struct gcov_info *next;
 	unsigned int stamp;
+ /* Since GCC 12.1 a checksum field is added. */
+#if (__GNUC__ >= 12)
+	unsigned int checksum;
+#endif
 	const char *filename;
 	void (*merge[GCOV_COUNTERS])(gcov_type *, unsigned int);
 	unsigned int n_functions;
@@ -383,12 +397,18 @@
 	pos += store_gcov_u32(buffer, pos, info->version);
 	pos += store_gcov_u32(buffer, pos, info->stamp);
 
+#if (__GNUC__ >= 12)
+	/* Use zero as checksum of the compilation unit. */
+	pos += store_gcov_u32(buffer, pos, 0);
+#endif
+
 	for (fi_idx = 0; fi_idx < info->n_functions; fi_idx++) {
 		fi_ptr = info->functions[fi_idx];
 
 		/* Function record. */
 		pos += store_gcov_u32(buffer, pos, GCOV_TAG_FUNCTION);
-		pos += store_gcov_u32(buffer, pos, GCOV_TAG_FUNCTION_LENGTH);
+		pos += store_gcov_u32(buffer, pos,
+			GCOV_TAG_FUNCTION_LENGTH * GCOV_UNIT_SIZE);
 		pos += store_gcov_u32(buffer, pos, fi_ptr->ident);
 		pos += store_gcov_u32(buffer, pos, fi_ptr->lineno_checksum);
 		pos += store_gcov_u32(buffer, pos, fi_ptr->cfg_checksum);
@@ -402,7 +422,8 @@
 			/* Counter record. */
 			pos += store_gcov_u32(buffer, pos,
 					      GCOV_TAG_FOR_COUNTER(ct_idx));
-			pos += store_gcov_u32(buffer, pos, ci_ptr->num * 2);
+			pos += store_gcov_u32(buffer, pos,
+				ci_ptr->num * 2 * GCOV_UNIT_SIZE);
 
 			for (cv_idx = 0; cv_idx < ci_ptr->num; cv_idx++) {
 				pos += store_gcov_u64(buffer, pos,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/gen_kheaders.sh
+++ linux-xilinx-zynqmp-5.15.0/kernel/gen_kheaders.sh
@@ -81,12 +81,10 @@
 	xargs -0 -P8 -n1 perl -pi -e 'BEGIN {undef $/;}; s/\/\*((?!SPDX).)*?\*\///smg;'
 
 # Create archive and try to normalize metadata for reproducibility.
-# For compatibility with older versions of tar, files are fed to tar
-# pre-sorted, as --sort=name might not be available.
-find $cpio_dir -printf "./%P\n" | LC_ALL=C sort | \
-    tar "${KBUILD_BUILD_TIMESTAMP:+--mtime=$KBUILD_BUILD_TIMESTAMP}" \
-    --owner=0 --group=0 --numeric-owner --no-recursion \
-    -I $XZ -cf $tarfile -C $cpio_dir/ -T - > /dev/null
+tar "${KBUILD_BUILD_TIMESTAMP:+--mtime=$KBUILD_BUILD_TIMESTAMP}" \
+    --exclude=".__afs*" --exclude=".nfs*" \
+    --owner=0 --group=0 --sort=name --numeric-owner --mode=u=rw,go=r,a+X \
+    -I $XZ -cf $tarfile -C $cpio_dir/ . > /dev/null
 
 echo $headers_md5 > kernel/kheaders.md5
 echo "$this_file_md5" >> kernel/kheaders.md5
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/hung_task.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/hung_task.c
@@ -63,7 +63,9 @@
  * Should we dump all CPUs backtraces in a hung task event?
  * Defaults to 0, can be changed via sysctl.
  */
-unsigned int __read_mostly sysctl_hung_task_all_cpu_backtrace;
+static unsigned int __read_mostly sysctl_hung_task_all_cpu_backtrace;
+#else
+#define sysctl_hung_task_all_cpu_backtrace 0
 #endif /* CONFIG_SMP */
 
 /*
@@ -222,11 +224,13 @@
 		MAX_SCHEDULE_TIMEOUT;
 }
 
+#ifdef CONFIG_SYSCTL
 /*
  * Process updating of timeout sysctl
  */
-int proc_dohung_task_timeout_secs(struct ctl_table *table, int write,
-				  void *buffer, size_t *lenp, loff_t *ppos)
+static int proc_dohung_task_timeout_secs(struct ctl_table *table, int write,
+				  void __user *buffer,
+				  size_t *lenp, loff_t *ppos)
 {
 	int ret;
 
@@ -241,6 +245,76 @@
 	return ret;
 }
 
+/*
+ * This is needed for proc_doulongvec_minmax of sysctl_hung_task_timeout_secs
+ * and hung_task_check_interval_secs
+ */
+static const unsigned long hung_task_timeout_max = (LONG_MAX / HZ);
+static struct ctl_table hung_task_sysctls[] = {
+#ifdef CONFIG_SMP
+	{
+		.procname	= "hung_task_all_cpu_backtrace",
+		.data		= &sysctl_hung_task_all_cpu_backtrace,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE,
+	},
+#endif /* CONFIG_SMP */
+	{
+		.procname	= "hung_task_panic",
+		.data		= &sysctl_hung_task_panic,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE,
+	},
+	{
+		.procname	= "hung_task_check_count",
+		.data		= &sysctl_hung_task_check_count,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= SYSCTL_ZERO,
+	},
+	{
+		.procname	= "hung_task_timeout_secs",
+		.data		= &sysctl_hung_task_timeout_secs,
+		.maxlen		= sizeof(unsigned long),
+		.mode		= 0644,
+		.proc_handler	= proc_dohung_task_timeout_secs,
+		.extra2		= (void *)&hung_task_timeout_max,
+	},
+	{
+		.procname	= "hung_task_check_interval_secs",
+		.data		= &sysctl_hung_task_check_interval_secs,
+		.maxlen		= sizeof(unsigned long),
+		.mode		= 0644,
+		.proc_handler	= proc_dohung_task_timeout_secs,
+		.extra2		= (void *)&hung_task_timeout_max,
+	},
+	{
+		.procname	= "hung_task_warnings",
+		.data		= &sysctl_hung_task_warnings,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= SYSCTL_NEG_ONE,
+	},
+	{}
+};
+
+static void __init hung_task_sysctl_init(void)
+{
+	register_sysctl_init("kernel", hung_task_sysctls);
+}
+#else
+#define hung_task_sysctl_init() do { } while (0)
+#endif /* CONFIG_SYSCTL */
+
+
 static atomic_t reset_hung_task = ATOMIC_INIT(0);
 
 void reset_hung_task_detector(void)
@@ -310,6 +384,7 @@
 	pm_notifier(hungtask_pm_notify, 0);
 
 	watchdog_task = kthread_run(watchdog, NULL, "khungtaskd");
+	hung_task_sysctl_init();
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/Kconfig
@@ -82,6 +82,7 @@
 # Generic IRQ IPI support
 config GENERIC_IRQ_IPI
 	bool
+	depends on SMP
 	select IRQ_DOMAIN_HIERARCHY
 
 # Generic MSI interrupt support
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/affinity.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/affinity.c
@@ -269,8 +269,9 @@
 	 */
 	if (numvecs <= nodes) {
 		for_each_node_mask(n, nodemsk) {
-			cpumask_or(&masks[curvec].mask, &masks[curvec].mask,
-				   node_to_cpumask[n]);
+			/* Ensure that only CPUs which are in both masks are set */
+			cpumask_and(nmsk, cpu_mask, node_to_cpumask[n]);
+			cpumask_or(&masks[curvec].mask, &masks[curvec].mask, nmsk);
 			if (++curvec == last_affv)
 				curvec = firstvec;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/chip.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/chip.c
@@ -38,7 +38,7 @@
  *	@irq:	irq number
  *	@chip:	pointer to irq chip description structure
  */
-int irq_set_chip(unsigned int irq, struct irq_chip *chip)
+int irq_set_chip(unsigned int irq, const struct irq_chip *chip)
 {
 	unsigned long flags;
 	struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0);
@@ -46,10 +46,7 @@
 	if (!desc)
 		return -EINVAL;
 
-	if (!chip)
-		chip = &no_irq_chip;
-
-	desc->irq_data.chip = chip;
+	desc->irq_data.chip = (struct irq_chip *)(chip ?: &no_irq_chip);
 	irq_put_desc_unlock(desc, flags);
 	/*
 	 * For !CONFIG_SPARSE_IRQ make the irq show up in
@@ -1075,7 +1072,7 @@
 EXPORT_SYMBOL_GPL(irq_set_chained_handler_and_data);
 
 void
-irq_set_chip_and_handler_name(unsigned int irq, struct irq_chip *chip,
+irq_set_chip_and_handler_name(unsigned int irq, const struct irq_chip *chip,
 			      irq_flow_handler_t handle, const char *name)
 {
 	irq_set_chip(irq, chip);
@@ -1516,7 +1513,8 @@
 	if (data->chip->irq_request_resources)
 		return data->chip->irq_request_resources(data);
 
-	return -ENOSYS;
+	/* no error on missing optional irq_chip::irq_request_resources */
+	return 0;
 }
 EXPORT_SYMBOL_GPL(irq_chip_request_resources_parent);
 
@@ -1558,6 +1556,17 @@
 	return 0;
 }
 
+static struct device *irq_get_parent_device(struct irq_data *data)
+{
+	if (data->chip->parent_device)
+		return data->chip->parent_device;
+
+	if (data->domain)
+		return data->domain->dev;
+
+	return NULL;
+}
+
 /**
  * irq_chip_pm_get - Enable power for an IRQ chip
  * @data:	Pointer to interrupt specific data
@@ -1567,12 +1576,13 @@
  */
 int irq_chip_pm_get(struct irq_data *data)
 {
+	struct device *dev = irq_get_parent_device(data);
 	int retval;
 
-	if (IS_ENABLED(CONFIG_PM) && data->chip->parent_device) {
-		retval = pm_runtime_get_sync(data->chip->parent_device);
+	if (IS_ENABLED(CONFIG_PM) && dev) {
+		retval = pm_runtime_get_sync(dev);
 		if (retval < 0) {
-			pm_runtime_put_noidle(data->chip->parent_device);
+			pm_runtime_put_noidle(dev);
 			return retval;
 		}
 	}
@@ -1590,10 +1600,11 @@
  */
 int irq_chip_pm_put(struct irq_data *data)
 {
+	struct device *dev = irq_get_parent_device(data);
 	int retval = 0;
 
-	if (IS_ENABLED(CONFIG_PM) && data->chip->parent_device)
-		retval = pm_runtime_put(data->chip->parent_device);
+	if (IS_ENABLED(CONFIG_PM) && dev)
+		retval = pm_runtime_put(dev);
 
 	return (retval < 0) ? retval : 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/cpuhotplug.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/cpuhotplug.c
@@ -70,6 +70,14 @@
 	}
 
 	/*
+	 * Complete an eventually pending irq move cleanup. If this
+	 * interrupt was moved in hard irq context, then the vectors need
+	 * to be cleaned up. It can't wait until this interrupt actually
+	 * happens and this CPU was involved.
+	 */
+	irq_force_complete_move(desc);
+
+	/*
 	 * No move required, if:
 	 * - Interrupt is per cpu
 	 * - Interrupt is not started
@@ -88,14 +96,6 @@
 	}
 
 	/*
-	 * Complete an eventually pending irq move cleanup. If this
-	 * interrupt was moved in hard irq context, then the vectors need
-	 * to be cleaned up. It can't wait until this interrupt actually
-	 * happens and this CPU was involved.
-	 */
-	irq_force_complete_move(desc);
-
-	/*
 	 * If there is a setaffinity pending, then try to reuse the pending
 	 * mask, so the last change of the affinity does not get lost. If
 	 * there is no move pending or the pending mask does not contain
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/generic-chip.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/generic-chip.c
@@ -541,21 +541,34 @@
 void irq_remove_generic_chip(struct irq_chip_generic *gc, u32 msk,
 			     unsigned int clr, unsigned int set)
 {
-	unsigned int i = gc->irq_base;
+	unsigned int i, virq;
 
 	raw_spin_lock(&gc_lock);
 	list_del(&gc->list);
 	raw_spin_unlock(&gc_lock);
 
-	for (; msk; msk >>= 1, i++) {
+	for (i = 0; msk; msk >>= 1, i++) {
 		if (!(msk & 0x01))
 			continue;
 
+		/*
+		 * Interrupt domain based chips store the base hardware
+		 * interrupt number in gc::irq_base. Otherwise gc::irq_base
+		 * contains the base Linux interrupt number.
+		 */
+		if (gc->domain) {
+			virq = irq_find_mapping(gc->domain, gc->irq_base + i);
+			if (!virq)
+				continue;
+		} else {
+			virq = gc->irq_base + i;
+		}
+
 		/* Remove handler first. That will mask the irq line */
-		irq_set_handler(i, NULL);
-		irq_set_chip(i, &no_irq_chip);
-		irq_set_chip_data(i, NULL);
-		irq_modify_status(i, clr, set);
+		irq_set_handler(virq, NULL);
+		irq_set_chip(virq, &no_irq_chip);
+		irq_set_chip_data(virq, NULL);
+		irq_modify_status(virq, clr, set);
 	}
 }
 EXPORT_SYMBOL_GPL(irq_remove_generic_chip);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/handle.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/handle.c
@@ -195,7 +195,7 @@
 
 	retval = __handle_irq_event_percpu(desc, &flags);
 
-	add_interrupt_randomness(desc->irq_data.irq, flags);
+	add_interrupt_randomness(desc->irq_data.irq);
 
 	if (!irq_settings_no_debug(desc))
 		note_interrupt(desc, retval);
@@ -218,7 +218,11 @@
 }
 
 #ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER
+#ifndef CONFIG_IRQCHIP_XILINX_INTC_MODULE_SUPPORT_EXPERIMENTAL
 int __init set_handle_irq(void (*handle_irq)(struct pt_regs *))
+#else
+int set_handle_irq(void (*handle_irq)(struct pt_regs *))
+#endif
 {
 	if (handle_arch_irq)
 		return -EBUSY;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/internals.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/internals.h
@@ -29,12 +29,14 @@
  * IRQTF_WARNED    - warning "IRQ_WAKE_THREAD w/o thread_fn" has been printed
  * IRQTF_AFFINITY  - irq thread is requested to adjust affinity
  * IRQTF_FORCED_THREAD  - irq action is force threaded
+ * IRQTF_READY     - signals that irq thread is ready
  */
 enum {
 	IRQTF_RUNTHREAD,
 	IRQTF_WARNED,
 	IRQTF_AFFINITY,
 	IRQTF_FORCED_THREAD,
+	IRQTF_READY,
 };
 
 /*
@@ -50,6 +52,7 @@
  * IRQS_PENDING			- irq is pending and replayed later
  * IRQS_SUSPENDED		- irq is suspended
  * IRQS_NMI			- irq line is used to deliver NMIs
+ * IRQS_SYSFS			- descriptor has been added to sysfs
  */
 enum {
 	IRQS_AUTODETECT		= 0x00000001,
@@ -62,6 +65,7 @@
 	IRQS_SUSPENDED		= 0x00000800,
 	IRQS_TIMINGS		= 0x00001000,
 	IRQS_NMI		= 0x00002000,
+	IRQS_SYSFS		= 0x00004000,
 };
 
 #include "debug.h"
@@ -425,10 +429,6 @@
 {
 	return desc->pending_mask;
 }
-static inline bool handle_enforce_irqctx(struct irq_data *data)
-{
-	return irqd_is_handle_enforce_irqctx(data);
-}
 bool irq_fixup_move_pending(struct irq_desc *desc, bool force_clear);
 #else /* CONFIG_GENERIC_PENDING_IRQ */
 static inline bool irq_can_move_pcntxt(struct irq_data *data)
@@ -455,11 +455,12 @@
 {
 	return false;
 }
+#endif /* !CONFIG_GENERIC_PENDING_IRQ */
+
 static inline bool handle_enforce_irqctx(struct irq_data *data)
 {
-	return false;
+	return irqd_is_handle_enforce_irqctx(data);
 }
-#endif /* !CONFIG_GENERIC_PENDING_IRQ */
 
 #if !defined(CONFIG_IRQ_DOMAIN) || !defined(CONFIG_IRQ_DOMAIN_HIERARCHY)
 static inline int irq_domain_activate_irq(struct irq_data *data, bool reserve)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/irqdesc.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/irqdesc.c
@@ -288,22 +288,25 @@
 	if (irq_kobj_base) {
 		/*
 		 * Continue even in case of failure as this is nothing
-		 * crucial.
+		 * crucial and failures in the late irq_sysfs_init()
+		 * cannot be rolled back.
 		 */
 		if (kobject_add(&desc->kobj, irq_kobj_base, "%d", irq))
 			pr_warn("Failed to add kobject for irq %d\n", irq);
+		else
+			desc->istate |= IRQS_SYSFS;
 	}
 }
 
 static void irq_sysfs_del(struct irq_desc *desc)
 {
 	/*
-	 * If irq_sysfs_init() has not yet been invoked (early boot), then
-	 * irq_kobj_base is NULL and the descriptor was never added.
-	 * kobject_del() complains about a object with no parent, so make
-	 * it conditional.
+	 * Only invoke kobject_del() when kobject_add() was successfully
+	 * invoked for the descriptor. This covers both early boot, where
+	 * sysfs is not initialized yet, and the case of a failed
+	 * kobject_add() invocation.
 	 */
-	if (irq_kobj_base)
+	if (desc->istate & IRQS_SYSFS)
 		kobject_del(&desc->kobj);
 }
 
@@ -352,9 +355,7 @@
 {
 	return radix_tree_lookup(&irq_desc_tree, irq);
 }
-#ifdef CONFIG_KVM_BOOK3S_64_HV_MODULE
 EXPORT_SYMBOL_GPL(irq_to_desc);
-#endif
 
 static void delete_irq_desc(unsigned int irq)
 {
@@ -407,6 +408,7 @@
 	lockdep_set_class(&desc->lock, &irq_desc_lock_class);
 	mutex_init(&desc->request_mutex);
 	init_rcu_head(&desc->rcu);
+	init_waitqueue_head(&desc->wait_for_threads);
 
 	desc_set_defaults(irq, desc, node, affinity, owner);
 	irqd_set(&desc->irq_data, flags);
@@ -489,6 +491,7 @@
 				flags = IRQD_AFFINITY_MANAGED |
 					IRQD_MANAGED_SHUTDOWN;
 			}
+			flags |= IRQD_AFFINITY_SET;
 			mask = &affinity->mask;
 			node = cpu_to_node(cpumask_first(mask));
 			affinity++;
@@ -575,6 +578,7 @@
 		raw_spin_lock_init(&desc[i].lock);
 		lockdep_set_class(&desc[i].lock, &irq_desc_lock_class);
 		mutex_init(&desc[i].request_mutex);
+		init_waitqueue_head(&desc[i].wait_for_threads);
 		desc_set_defaults(i, &desc[i], node, NULL, NULL);
 	}
 	return arch_early_irq_init();
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/irqdomain.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/irqdomain.c
@@ -25,6 +25,9 @@
 
 static struct irq_domain *irq_default_domain;
 
+static int irq_domain_alloc_irqs_locked(struct irq_domain *domain, int irq_base,
+					unsigned int nr_irqs, int node, void *arg,
+					bool realloc, const struct irq_affinity_desc *affinity);
 static void irq_domain_check_hierarchy(struct irq_domain *domain);
 
 struct irqchip_fwid {
@@ -123,23 +126,12 @@
 }
 EXPORT_SYMBOL_GPL(irq_domain_free_fwnode);
 
-/**
- * __irq_domain_add() - Allocate a new irq_domain data structure
- * @fwnode: firmware node for the interrupt controller
- * @size: Size of linear map; 0 for radix mapping only
- * @hwirq_max: Maximum number of interrupts supported by controller
- * @direct_max: Maximum value of direct maps; Use ~0 for no limit; 0 for no
- *              direct mapping
- * @ops: domain callbacks
- * @host_data: Controller private data pointer
- *
- * Allocates and initializes an irq_domain structure.
- * Returns pointer to IRQ domain, or NULL on failure.
- */
-struct irq_domain *__irq_domain_add(struct fwnode_handle *fwnode, unsigned int size,
-				    irq_hw_number_t hwirq_max, int direct_max,
-				    const struct irq_domain_ops *ops,
-				    void *host_data)
+static struct irq_domain *__irq_domain_create(struct fwnode_handle *fwnode,
+					      unsigned int size,
+					      irq_hw_number_t hwirq_max,
+					      int direct_max,
+					      const struct irq_domain_ops *ops,
+					      void *host_data)
 {
 	struct irqchip_fwid *fwid;
 	struct irq_domain *domain;
@@ -161,7 +153,6 @@
 		switch (fwid->type) {
 		case IRQCHIP_FWNODE_NAMED:
 		case IRQCHIP_FWNODE_NAMED_ID:
-			domain->fwnode = fwnode;
 			domain->name = kstrdup(fwid->name, GFP_KERNEL);
 			if (!domain->name) {
 				kfree(domain);
@@ -170,7 +161,6 @@
 			domain->flags |= IRQ_DOMAIN_NAME_ALLOCATED;
 			break;
 		default:
-			domain->fwnode = fwnode;
 			domain->name = fwid->name;
 			break;
 		}
@@ -192,7 +182,6 @@
 		strreplace(name, '/', ':');
 
 		domain->name = name;
-		domain->fwnode = fwnode;
 		domain->flags |= IRQ_DOMAIN_NAME_ALLOCATED;
 	}
 
@@ -208,8 +197,8 @@
 		domain->flags |= IRQ_DOMAIN_NAME_ALLOCATED;
 	}
 
-	fwnode_handle_get(fwnode);
-	fwnode_dev_initialized(fwnode, true);
+	domain->fwnode = fwnode_handle_get(fwnode);
+	fwnode_dev_initialized(domain->fwnode, true);
 
 	/* Fill structure */
 	INIT_RADIX_TREE(&domain->revmap_tree, GFP_KERNEL);
@@ -227,12 +216,44 @@
 
 	irq_domain_check_hierarchy(domain);
 
+	return domain;
+}
+
+static void __irq_domain_publish(struct irq_domain *domain)
+{
 	mutex_lock(&irq_domain_mutex);
 	debugfs_add_domain_dir(domain);
 	list_add(&domain->link, &irq_domain_list);
 	mutex_unlock(&irq_domain_mutex);
 
 	pr_debug("Added domain %s\n", domain->name);
+}
+
+/**
+ * __irq_domain_add() - Allocate a new irq_domain data structure
+ * @fwnode: firmware node for the interrupt controller
+ * @size: Size of linear map; 0 for radix mapping only
+ * @hwirq_max: Maximum number of interrupts supported by controller
+ * @direct_max: Maximum value of direct maps; Use ~0 for no limit; 0 for no
+ *              direct mapping
+ * @ops: domain callbacks
+ * @host_data: Controller private data pointer
+ *
+ * Allocates and initializes an irq_domain structure.
+ * Returns pointer to IRQ domain, or NULL on failure.
+ */
+struct irq_domain *__irq_domain_add(struct fwnode_handle *fwnode, unsigned int size,
+				    irq_hw_number_t hwirq_max, int direct_max,
+				    const struct irq_domain_ops *ops,
+				    void *host_data)
+{
+	struct irq_domain *domain;
+
+	domain = __irq_domain_create(fwnode, size, hwirq_max, direct_max,
+				     ops, host_data);
+	if (domain)
+		__irq_domain_publish(domain);
+
 	return domain;
 }
 EXPORT_SYMBOL_GPL(__irq_domain_add);
@@ -538,6 +559,9 @@
 		return;
 
 	hwirq = irq_data->hwirq;
+
+	mutex_lock(&irq_domain_mutex);
+
 	irq_set_status_flags(irq, IRQ_NOREQUEST);
 
 	/* remove chip and handler */
@@ -557,10 +581,12 @@
 
 	/* Clear reverse map for this hwirq */
 	irq_domain_clear_mapping(domain, hwirq);
+
+	mutex_unlock(&irq_domain_mutex);
 }
 
-int irq_domain_associate(struct irq_domain *domain, unsigned int virq,
-			 irq_hw_number_t hwirq)
+static int irq_domain_associate_locked(struct irq_domain *domain, unsigned int virq,
+				       irq_hw_number_t hwirq)
 {
 	struct irq_data *irq_data = irq_get_irq_data(virq);
 	int ret;
@@ -573,7 +599,6 @@
 	if (WARN(irq_data->domain, "error: virq%i is already associated", virq))
 		return -EINVAL;
 
-	mutex_lock(&irq_domain_mutex);
 	irq_data->hwirq = hwirq;
 	irq_data->domain = domain;
 	if (domain->ops->map) {
@@ -590,7 +615,6 @@
 			}
 			irq_data->domain = NULL;
 			irq_data->hwirq = 0;
-			mutex_unlock(&irq_domain_mutex);
 			return ret;
 		}
 
@@ -601,12 +625,23 @@
 
 	domain->mapcount++;
 	irq_domain_set_mapping(domain, hwirq, irq_data);
-	mutex_unlock(&irq_domain_mutex);
 
 	irq_clear_status_flags(virq, IRQ_NOREQUEST);
 
 	return 0;
 }
+
+int irq_domain_associate(struct irq_domain *domain, unsigned int virq,
+			 irq_hw_number_t hwirq)
+{
+	int ret;
+
+	mutex_lock(&irq_domain_mutex);
+	ret = irq_domain_associate_locked(domain, virq, hwirq);
+	mutex_unlock(&irq_domain_mutex);
+
+	return ret;
+}
 EXPORT_SYMBOL_GPL(irq_domain_associate);
 
 void irq_domain_associate_many(struct irq_domain *domain, unsigned int irq_base,
@@ -668,6 +703,34 @@
 EXPORT_SYMBOL_GPL(irq_create_direct_mapping);
 #endif
 
+static unsigned int irq_create_mapping_affinity_locked(struct irq_domain *domain,
+						       irq_hw_number_t hwirq,
+						       const struct irq_affinity_desc *affinity)
+{
+	struct device_node *of_node = irq_domain_get_of_node(domain);
+	int virq;
+
+	pr_debug("irq_create_mapping(0x%p, 0x%lx)\n", domain, hwirq);
+
+	/* Allocate a virtual interrupt number */
+	virq = irq_domain_alloc_descs(-1, 1, hwirq, of_node_to_nid(of_node),
+				      affinity);
+	if (virq <= 0) {
+		pr_debug("-> virq allocation failed\n");
+		return 0;
+	}
+
+	if (irq_domain_associate_locked(domain, virq, hwirq)) {
+		irq_free_desc(virq);
+		return 0;
+	}
+
+	pr_debug("irq %lu on domain %s mapped to virtual irq %u\n",
+		hwirq, of_node_full_name(of_node), virq);
+
+	return virq;
+}
+
 /**
  * irq_create_mapping_affinity() - Map a hardware interrupt into linux irq space
  * @domain: domain owning this hardware interrupt or NULL for default domain
@@ -680,14 +743,11 @@
  * on the number returned from that call.
  */
 unsigned int irq_create_mapping_affinity(struct irq_domain *domain,
-				       irq_hw_number_t hwirq,
-				       const struct irq_affinity_desc *affinity)
+					 irq_hw_number_t hwirq,
+					 const struct irq_affinity_desc *affinity)
 {
-	struct device_node *of_node;
 	int virq;
 
-	pr_debug("irq_create_mapping(0x%p, 0x%lx)\n", domain, hwirq);
-
 	/* Look for default domain if necessary */
 	if (domain == NULL)
 		domain = irq_default_domain;
@@ -695,32 +755,19 @@
 		WARN(1, "%s(, %lx) called with NULL domain\n", __func__, hwirq);
 		return 0;
 	}
-	pr_debug("-> using domain @%p\n", domain);
 
-	of_node = irq_domain_get_of_node(domain);
+	mutex_lock(&irq_domain_mutex);
 
 	/* Check if mapping already exists */
 	virq = irq_find_mapping(domain, hwirq);
 	if (virq) {
-		pr_debug("-> existing mapping on virq %d\n", virq);
-		return virq;
-	}
-
-	/* Allocate a virtual interrupt number */
-	virq = irq_domain_alloc_descs(-1, 1, hwirq, of_node_to_nid(of_node),
-				      affinity);
-	if (virq <= 0) {
-		pr_debug("-> virq allocation failed\n");
-		return 0;
+		pr_debug("existing mapping on virq %d\n", virq);
+		goto out;
 	}
 
-	if (irq_domain_associate(domain, virq, hwirq)) {
-		irq_free_desc(virq);
-		return 0;
-	}
-
-	pr_debug("irq %lu on domain %s mapped to virtual irq %u\n",
-		hwirq, of_node_full_name(of_node), virq);
+	virq = irq_create_mapping_affinity_locked(domain, hwirq, affinity);
+out:
+	mutex_unlock(&irq_domain_mutex);
 
 	return virq;
 }
@@ -789,6 +836,8 @@
 	if (WARN_ON(type & ~IRQ_TYPE_SENSE_MASK))
 		type &= IRQ_TYPE_SENSE_MASK;
 
+	mutex_lock(&irq_domain_mutex);
+
 	/*
 	 * If we've already configured this interrupt,
 	 * don't do it again, or hell will break loose.
@@ -801,7 +850,7 @@
 		 * interrupt number.
 		 */
 		if (type == IRQ_TYPE_NONE || type == irq_get_trigger_type(virq))
-			return virq;
+			goto out;
 
 		/*
 		 * If the trigger type has not been set yet, then set
@@ -809,40 +858,45 @@
 		 */
 		if (irq_get_trigger_type(virq) == IRQ_TYPE_NONE) {
 			irq_data = irq_get_irq_data(virq);
-			if (!irq_data)
-				return 0;
+			if (!irq_data) {
+				virq = 0;
+				goto out;
+			}
 
 			irqd_set_trigger_type(irq_data, type);
-			return virq;
+			goto out;
 		}
 
 		pr_warn("type mismatch, failed to map hwirq-%lu for %s!\n",
 			hwirq, of_node_full_name(to_of_node(fwspec->fwnode)));
-		return 0;
+		virq = 0;
+		goto out;
 	}
 
 	if (irq_domain_is_hierarchy(domain)) {
-		virq = irq_domain_alloc_irqs(domain, 1, NUMA_NO_NODE, fwspec);
-		if (virq <= 0)
-			return 0;
+		virq = irq_domain_alloc_irqs_locked(domain, -1, 1, NUMA_NO_NODE,
+						    fwspec, false, NULL);
+		if (virq <= 0) {
+			virq = 0;
+			goto out;
+		}
 	} else {
 		/* Create mapping */
-		virq = irq_create_mapping(domain, hwirq);
+		virq = irq_create_mapping_affinity_locked(domain, hwirq, NULL);
 		if (!virq)
-			return virq;
+			goto out;
 	}
 
 	irq_data = irq_get_irq_data(virq);
-	if (!irq_data) {
-		if (irq_domain_is_hierarchy(domain))
-			irq_domain_free_irqs(virq, 1);
-		else
-			irq_dispose_mapping(virq);
-		return 0;
+	if (WARN_ON(!irq_data)) {
+		virq = 0;
+		goto out;
 	}
 
 	/* Store trigger type */
 	irqd_set_trigger_type(irq_data, type);
+out:
+	mutex_unlock(&irq_domain_mutex);
 
 	return virq;
 }
@@ -910,6 +964,8 @@
 			data = irq_domain_get_irq_data(domain, hwirq);
 			if (data && data->hwirq == hwirq)
 				desc = irq_data_to_desc(data);
+			if (irq && desc)
+				*irq = hwirq;
 		}
 
 		return desc;
@@ -1100,12 +1156,15 @@
 	struct irq_domain *domain;
 
 	if (size)
-		domain = irq_domain_create_linear(fwnode, size, ops, host_data);
+		domain = __irq_domain_create(fwnode, size, size, 0, ops, host_data);
 	else
-		domain = irq_domain_create_tree(fwnode, ops, host_data);
+		domain = __irq_domain_create(fwnode, 0, ~0, 0, ops, host_data);
+
 	if (domain) {
 		domain->parent = parent;
 		domain->flags |= flags;
+
+		__irq_domain_publish(domain);
 	}
 
 	return domain;
@@ -1423,40 +1482,12 @@
 	return domain->ops->alloc(domain, irq_base, nr_irqs, arg);
 }
 
-/**
- * __irq_domain_alloc_irqs - Allocate IRQs from domain
- * @domain:	domain to allocate from
- * @irq_base:	allocate specified IRQ number if irq_base >= 0
- * @nr_irqs:	number of IRQs to allocate
- * @node:	NUMA node id for memory allocation
- * @arg:	domain specific argument
- * @realloc:	IRQ descriptors have already been allocated if true
- * @affinity:	Optional irq affinity mask for multiqueue devices
- *
- * Allocate IRQ numbers and initialized all data structures to support
- * hierarchy IRQ domains.
- * Parameter @realloc is mainly to support legacy IRQs.
- * Returns error code or allocated IRQ number
- *
- * The whole process to setup an IRQ has been split into two steps.
- * The first step, __irq_domain_alloc_irqs(), is to allocate IRQ
- * descriptor and required hardware resources. The second step,
- * irq_domain_activate_irq(), is to program the hardware with preallocated
- * resources. In this way, it's easier to rollback when failing to
- * allocate resources.
- */
-int __irq_domain_alloc_irqs(struct irq_domain *domain, int irq_base,
-			    unsigned int nr_irqs, int node, void *arg,
-			    bool realloc, const struct irq_affinity_desc *affinity)
+static int irq_domain_alloc_irqs_locked(struct irq_domain *domain, int irq_base,
+					unsigned int nr_irqs, int node, void *arg,
+					bool realloc, const struct irq_affinity_desc *affinity)
 {
 	int i, ret, virq;
 
-	if (domain == NULL) {
-		domain = irq_default_domain;
-		if (WARN(!domain, "domain is NULL; cannot allocate IRQ\n"))
-			return -EINVAL;
-	}
-
 	if (realloc && irq_base >= 0) {
 		virq = irq_base;
 	} else {
@@ -1475,24 +1506,18 @@
 		goto out_free_desc;
 	}
 
-	mutex_lock(&irq_domain_mutex);
 	ret = irq_domain_alloc_irqs_hierarchy(domain, virq, nr_irqs, arg);
-	if (ret < 0) {
-		mutex_unlock(&irq_domain_mutex);
+	if (ret < 0)
 		goto out_free_irq_data;
-	}
 
 	for (i = 0; i < nr_irqs; i++) {
 		ret = irq_domain_trim_hierarchy(virq + i);
-		if (ret) {
-			mutex_unlock(&irq_domain_mutex);
+		if (ret)
 			goto out_free_irq_data;
-		}
 	}
-	
+
 	for (i = 0; i < nr_irqs; i++)
 		irq_domain_insert_irq(virq + i);
-	mutex_unlock(&irq_domain_mutex);
 
 	return virq;
 
@@ -1503,6 +1528,48 @@
 	return ret;
 }
 
+/**
+ * __irq_domain_alloc_irqs - Allocate IRQs from domain
+ * @domain:	domain to allocate from
+ * @irq_base:	allocate specified IRQ number if irq_base >= 0
+ * @nr_irqs:	number of IRQs to allocate
+ * @node:	NUMA node id for memory allocation
+ * @arg:	domain specific argument
+ * @realloc:	IRQ descriptors have already been allocated if true
+ * @affinity:	Optional irq affinity mask for multiqueue devices
+ *
+ * Allocate IRQ numbers and initialized all data structures to support
+ * hierarchy IRQ domains.
+ * Parameter @realloc is mainly to support legacy IRQs.
+ * Returns error code or allocated IRQ number
+ *
+ * The whole process to setup an IRQ has been split into two steps.
+ * The first step, __irq_domain_alloc_irqs(), is to allocate IRQ
+ * descriptor and required hardware resources. The second step,
+ * irq_domain_activate_irq(), is to program the hardware with preallocated
+ * resources. In this way, it's easier to rollback when failing to
+ * allocate resources.
+ */
+int __irq_domain_alloc_irqs(struct irq_domain *domain, int irq_base,
+			    unsigned int nr_irqs, int node, void *arg,
+			    bool realloc, const struct irq_affinity_desc *affinity)
+{
+	int ret;
+
+	if (domain == NULL) {
+		domain = irq_default_domain;
+		if (WARN(!domain, "domain is NULL; cannot allocate IRQ\n"))
+			return -EINVAL;
+	}
+
+	mutex_lock(&irq_domain_mutex);
+	ret = irq_domain_alloc_irqs_locked(domain, irq_base, nr_irqs, node, arg,
+					   realloc, affinity);
+	mutex_unlock(&irq_domain_mutex);
+
+	return ret;
+}
+
 /* The irq_data was moved, fix the revmap to refer to the new location */
 static void irq_domain_fix_revmap(struct irq_data *d)
 {
@@ -1861,6 +1928,13 @@
 	irq_set_handler_data(virq, handler_data);
 }
 
+static int irq_domain_alloc_irqs_locked(struct irq_domain *domain, int irq_base,
+					unsigned int nr_irqs, int node, void *arg,
+					bool realloc, const struct irq_affinity_desc *affinity)
+{
+	return -EINVAL;
+}
+
 static void irq_domain_check_hierarchy(struct irq_domain *domain)
 {
 }
@@ -1911,7 +1985,7 @@
 
 static void debugfs_remove_domain_dir(struct irq_domain *d)
 {
-	debugfs_remove(debugfs_lookup(d->name, domain_dir));
+	debugfs_lookup_and_remove(d->name, domain_dir);
 }
 
 void __init irq_domain_debugfs_init(struct dentry *root)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/manage.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/manage.c
@@ -222,11 +222,16 @@
 {
 	struct irq_desc *desc = irq_data_to_desc(data);
 	struct irq_chip *chip = irq_data_get_irq_chip(data);
+	const struct cpumask  *prog_mask;
 	int ret;
 
+	static DEFINE_RAW_SPINLOCK(tmp_mask_lock);
+	static struct cpumask tmp_mask;
+
 	if (!chip || !chip->irq_set_affinity)
 		return -EINVAL;
 
+	raw_spin_lock(&tmp_mask_lock);
 	/*
 	 * If this is a managed interrupt and housekeeping is enabled on
 	 * it check whether the requested affinity mask intersects with
@@ -248,24 +253,34 @@
 	 */
 	if (irqd_affinity_is_managed(data) &&
 	    housekeeping_enabled(HK_FLAG_MANAGED_IRQ)) {
-		const struct cpumask *hk_mask, *prog_mask;
-
-		static DEFINE_RAW_SPINLOCK(tmp_mask_lock);
-		static struct cpumask tmp_mask;
+		const struct cpumask *hk_mask;
 
 		hk_mask = housekeeping_cpumask(HK_FLAG_MANAGED_IRQ);
 
-		raw_spin_lock(&tmp_mask_lock);
 		cpumask_and(&tmp_mask, mask, hk_mask);
 		if (!cpumask_intersects(&tmp_mask, cpu_online_mask))
 			prog_mask = mask;
 		else
 			prog_mask = &tmp_mask;
-		ret = chip->irq_set_affinity(data, prog_mask, force);
-		raw_spin_unlock(&tmp_mask_lock);
 	} else {
-		ret = chip->irq_set_affinity(data, mask, force);
+		prog_mask = mask;
 	}
+
+	/*
+	 * Make sure we only provide online CPUs to the irqchip,
+	 * unless we are being asked to force the affinity (in which
+	 * case we do as we are told).
+	 */
+	cpumask_and(&tmp_mask, prog_mask, cpu_online_mask);
+	if (!force && !cpumask_empty(&tmp_mask))
+		ret = chip->irq_set_affinity(data, &tmp_mask, force);
+	else if (force)
+		ret = chip->irq_set_affinity(data, mask, force);
+	else
+		ret = -EINVAL;
+
+	raw_spin_unlock(&tmp_mask_lock);
+
 	switch (ret) {
 	case IRQ_SET_MASK_OK:
 	case IRQ_SET_MASK_OK_DONE:
@@ -1249,6 +1264,31 @@
 }
 
 /*
+ * Internal function to notify that a interrupt thread is ready.
+ */
+static void irq_thread_set_ready(struct irq_desc *desc,
+				 struct irqaction *action)
+{
+	set_bit(IRQTF_READY, &action->thread_flags);
+	wake_up(&desc->wait_for_threads);
+}
+
+/*
+ * Internal function to wake up a interrupt thread and wait until it is
+ * ready.
+ */
+static void wake_up_and_wait_for_irq_thread_ready(struct irq_desc *desc,
+						  struct irqaction *action)
+{
+	if (!action || !action->thread)
+		return;
+
+	wake_up_process(action->thread);
+	wait_event(desc->wait_for_threads,
+		   test_bit(IRQTF_READY, &action->thread_flags));
+}
+
+/*
  * Interrupt handler thread
  */
 static int irq_thread(void *data)
@@ -1259,6 +1299,8 @@
 	irqreturn_t (*handler_fn)(struct irq_desc *desc,
 			struct irqaction *action);
 
+	irq_thread_set_ready(desc, action);
+
 	if (force_irqthreads() && test_bit(IRQTF_FORCED_THREAD,
 					   &action->thread_flags))
 		handler_fn = irq_forced_thread_fn;
@@ -1288,7 +1330,7 @@
 	 * synchronize_hardirq(). So neither IRQTF_RUNTHREAD nor the
 	 * oneshot mask bit can be set.
 	 */
-	task_work_cancel(current, irq_thread_dtor);
+	task_work_cancel_func(current, irq_thread_dtor);
 	return 0;
 }
 
@@ -1683,8 +1725,6 @@
 	}
 
 	if (!shared) {
-		init_waitqueue_head(&desc->wait_for_threads);
-
 		/* Setup the type (level, edge polarity) if configured: */
 		if (new->flags & IRQF_TRIGGER_MASK) {
 			ret = __irq_set_trigger(desc,
@@ -1780,14 +1820,8 @@
 
 	irq_setup_timings(desc, new);
 
-	/*
-	 * Strictly no need to wake it up, but hung_task complains
-	 * when no hard interrupt wakes the thread up.
-	 */
-	if (new->thread)
-		wake_up_process(new->thread);
-	if (new->secondary)
-		wake_up_process(new->secondary->thread);
+	wake_up_and_wait_for_irq_thread_ready(desc, new);
+	wake_up_and_wait_for_irq_thread_ready(desc, new->secondary);
 
 	register_irq_proc(irq, desc);
 	new->dir = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/matrix.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/matrix.c
@@ -466,16 +466,16 @@
 }
 
 /**
- * irq_matrix_allocated - Get the number of allocated irqs on the local cpu
+ * irq_matrix_allocated - Get the number of allocated non-managed irqs on the local CPU
  * @m:		Pointer to the matrix to search
  *
- * This returns number of allocated irqs
+ * This returns number of allocated non-managed interrupts.
  */
 unsigned int irq_matrix_allocated(struct irq_matrix *m)
 {
 	struct cpumap *cm = this_cpu_ptr(m->maps);
 
-	return cm->allocated;
+	return cm->allocated - cm->managed_allocated;
 }
 
 #ifdef CONFIG_GENERIC_IRQ_DEBUGFS
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/irq/msi.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/irq/msi.c
@@ -529,10 +529,10 @@
 
 	/*
 	 * Checking the first MSI descriptor is sufficient. MSIX supports
-	 * masking and MSI does so when the maskbit is set.
+	 * masking and MSI does so when the can_mask attribute is set.
 	 */
 	desc = first_msi_entry(dev);
-	return desc->msi_attrib.is_msix || desc->msi_attrib.maskbit;
+	return desc->msi_attrib.is_msix || desc->msi_attrib.can_mask;
 }
 
 int __msi_domain_alloc_irqs(struct irq_domain *domain, struct device *dev,
@@ -596,6 +596,13 @@
 			irqd_clr_can_reserve(irq_data);
 			if (domain->flags & IRQ_DOMAIN_MSI_NOMASK_QUIRK)
 				irqd_set_msi_nomask_quirk(irq_data);
+			if ((info->flags & MSI_FLAG_ACTIVATE_EARLY) &&
+				irqd_affinity_is_managed(irq_data) &&
+				!cpumask_intersects(irq_data_get_affinity_mask(irq_data),
+						    cpu_online_mask)) {
+				irqd_set_managed_shutdown(irq_data);
+				continue;
+			}
 		}
 		ret = irq_domain_activate_irq(irq_data, can_reserve);
 		if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kallsyms.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kallsyms.c
@@ -204,7 +204,6 @@
 	return module_kallsyms_lookup_name(name);
 }
 
-#ifdef CONFIG_LIVEPATCH
 /*
  * Iterate over all symbols in vmlinux.  For symbols from modules use
  * module_kallsyms_on_each_symbol instead.
@@ -226,7 +225,6 @@
 	}
 	return 0;
 }
-#endif /* CONFIG_LIVEPATCH */
 
 static unsigned long get_symbol_pos(unsigned long addr,
 				    unsigned long *symbolsize,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kcov.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kcov.c
@@ -151,6 +151,15 @@
 	list_add(&area->list, &kcov_remote_areas);
 }
 
+/*
+ * Unlike in_serving_softirq(), this function returns false when called during
+ * a hardirq or an NMI that happened in the softirq context.
+ */
+static __always_inline bool in_softirq_really(void)
+{
+	return in_serving_softirq() && !in_hardirq() && !in_nmi();
+}
+
 static notrace bool check_kcov_mode(enum kcov_mode needed_mode, struct task_struct *t)
 {
 	unsigned int mode;
@@ -160,7 +169,7 @@
 	 * so we ignore code executed in interrupts, unless we are in a remote
 	 * coverage collection section in a softirq.
 	 */
-	if (!in_task() && !(in_serving_softirq() && t->kcov_softirq))
+	if (!in_task() && !(in_softirq_really() && t->kcov_softirq))
 		return false;
 	mode = READ_ONCE(t->kcov_mode);
 	/*
@@ -635,6 +644,7 @@
 			return -EINVAL;
 		kcov->mode = mode;
 		t->kcov = kcov;
+	        t->kcov_mode = KCOV_MODE_REMOTE;
 		kcov->t = t;
 		kcov->remote = true;
 		kcov->remote_size = remote_arg->area_size;
@@ -821,7 +831,7 @@
 
 	if (WARN_ON(!kcov_check_handle(handle, true, true, true)))
 		return;
-	if (!in_task() && !in_serving_softirq())
+	if (!in_task() && !in_softirq_really())
 		return;
 
 	local_irq_save(flags);
@@ -962,7 +972,7 @@
 	int sequence;
 	unsigned long flags;
 
-	if (!in_task() && !in_serving_softirq())
+	if (!in_task() && !in_softirq_really())
 		return;
 
 	local_irq_save(flags);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kcsan/Makefile
+++ linux-xilinx-zynqmp-5.15.0/kernel/kcsan/Makefile
@@ -13,5 +13,6 @@
 obj-y := core.o debugfs.o report.o
 obj-$(CONFIG_KCSAN_SELFTEST) += selftest.o
 
-CFLAGS_kcsan_test.o := $(CFLAGS_KCSAN) -g -fno-omit-frame-pointer
+CFLAGS_kcsan_test.o := $(CFLAGS_KCSAN) -fno-omit-frame-pointer
+CFLAGS_kcsan_test.o += $(DISABLE_STRUCTLEAK_PLUGIN)
 obj-$(CONFIG_KCSAN_KUNIT_TEST) += kcsan_test.o
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kcsan/core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kcsan/core.c
@@ -14,10 +14,12 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/list.h>
+#include <linux/minmax.h>
 #include <linux/moduleparam.h>
 #include <linux/percpu.h>
 #include <linux/preempt.h>
 #include <linux/sched.h>
+#include <linux/string.h>
 #include <linux/uaccess.h>
 
 #include "encoding.h"
@@ -1048,7 +1050,9 @@
 DEFINE_TSAN_ATOMIC_OPS(8);
 DEFINE_TSAN_ATOMIC_OPS(16);
 DEFINE_TSAN_ATOMIC_OPS(32);
+#ifdef CONFIG_64BIT
 DEFINE_TSAN_ATOMIC_OPS(64);
+#endif
 
 void __tsan_atomic_thread_fence(int memorder);
 void __tsan_atomic_thread_fence(int memorder)
@@ -1060,3 +1064,51 @@
 void __tsan_atomic_signal_fence(int memorder);
 void __tsan_atomic_signal_fence(int memorder) { }
 EXPORT_SYMBOL(__tsan_atomic_signal_fence);
+
+#ifdef __HAVE_ARCH_MEMSET
+void *__tsan_memset(void *s, int c, size_t count);
+noinline void *__tsan_memset(void *s, int c, size_t count)
+{
+	/*
+	 * Instead of not setting up watchpoints where accessed size is greater
+	 * than MAX_ENCODABLE_SIZE, truncate checked size to MAX_ENCODABLE_SIZE.
+	 */
+	size_t check_len = min_t(size_t, count, MAX_ENCODABLE_SIZE);
+
+	check_access(s, check_len, KCSAN_ACCESS_WRITE);
+	return memset(s, c, count);
+}
+#else
+void *__tsan_memset(void *s, int c, size_t count) __alias(memset);
+#endif
+EXPORT_SYMBOL(__tsan_memset);
+
+#ifdef __HAVE_ARCH_MEMMOVE
+void *__tsan_memmove(void *dst, const void *src, size_t len);
+noinline void *__tsan_memmove(void *dst, const void *src, size_t len)
+{
+	size_t check_len = min_t(size_t, len, MAX_ENCODABLE_SIZE);
+
+	check_access(dst, check_len, KCSAN_ACCESS_WRITE);
+	check_access(src, check_len, 0);
+	return memmove(dst, src, len);
+}
+#else
+void *__tsan_memmove(void *dst, const void *src, size_t len) __alias(memmove);
+#endif
+EXPORT_SYMBOL(__tsan_memmove);
+
+#ifdef __HAVE_ARCH_MEMCPY
+void *__tsan_memcpy(void *dst, const void *src, size_t len);
+noinline void *__tsan_memcpy(void *dst, const void *src, size_t len)
+{
+	size_t check_len = min_t(size_t, len, MAX_ENCODABLE_SIZE);
+
+	check_access(dst, check_len, KCSAN_ACCESS_WRITE);
+	check_access(src, check_len, 0);
+	return memcpy(dst, src, len);
+}
+#else
+void *__tsan_memcpy(void *dst, const void *src, size_t len) __alias(memcpy);
+#endif
+EXPORT_SYMBOL(__tsan_memcpy);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kcsan/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kcsan/debugfs.c
@@ -46,14 +46,8 @@
 	int		used;		/* number of elements used */
 	bool		sorted;		/* if elements are sorted */
 	bool		whitelist;	/* if list is a blacklist or whitelist */
-} report_filterlist = {
-	.addrs		= NULL,
-	.size		= 8,		/* small initial size */
-	.used		= 0,
-	.sorted		= false,
-	.whitelist	= false,	/* default is blacklist */
-};
-static DEFINE_SPINLOCK(report_filterlist_lock);
+} report_filterlist;
+static DEFINE_RAW_SPINLOCK(report_filterlist_lock);
 
 /*
  * The microbenchmark allows benchmarking KCSAN core runtime only. To run
@@ -110,7 +104,7 @@
 		return false;
 	func_addr -= offset; /* Get function start */
 
-	spin_lock_irqsave(&report_filterlist_lock, flags);
+	raw_spin_lock_irqsave(&report_filterlist_lock, flags);
 	if (report_filterlist.used == 0)
 		goto out;
 
@@ -127,7 +121,7 @@
 		ret = !ret;
 
 out:
-	spin_unlock_irqrestore(&report_filterlist_lock, flags);
+	raw_spin_unlock_irqrestore(&report_filterlist_lock, flags);
 	return ret;
 }
 
@@ -135,9 +129,9 @@
 {
 	unsigned long flags;
 
-	spin_lock_irqsave(&report_filterlist_lock, flags);
+	raw_spin_lock_irqsave(&report_filterlist_lock, flags);
 	report_filterlist.whitelist = whitelist;
-	spin_unlock_irqrestore(&report_filterlist_lock, flags);
+	raw_spin_unlock_irqrestore(&report_filterlist_lock, flags);
 }
 
 /* Returns 0 on success, error-code otherwise. */
@@ -145,6 +139,9 @@
 {
 	unsigned long flags;
 	unsigned long addr = kallsyms_lookup_name(func);
+	unsigned long *delay_free = NULL;
+	unsigned long *new_addrs = NULL;
+	size_t new_size = 0;
 	ssize_t ret = 0;
 
 	if (!addr) {
@@ -152,32 +149,33 @@
 		return -ENOENT;
 	}
 
-	spin_lock_irqsave(&report_filterlist_lock, flags);
+retry_alloc:
+	/*
+	 * Check if we need an allocation, and re-validate under the lock. Since
+	 * the report_filterlist_lock is a raw, cannot allocate under the lock.
+	 */
+	if (data_race(report_filterlist.used == report_filterlist.size)) {
+		new_size = (report_filterlist.size ?: 4) * 2;
+		delay_free = new_addrs = kmalloc_array(new_size, sizeof(unsigned long), GFP_KERNEL);
+		if (!new_addrs)
+			return -ENOMEM;
+	}
 
-	if (report_filterlist.addrs == NULL) {
-		/* initial allocation */
-		report_filterlist.addrs =
-			kmalloc_array(report_filterlist.size,
-				      sizeof(unsigned long), GFP_ATOMIC);
-		if (report_filterlist.addrs == NULL) {
-			ret = -ENOMEM;
-			goto out;
-		}
-	} else if (report_filterlist.used == report_filterlist.size) {
-		/* resize filterlist */
-		size_t new_size = report_filterlist.size * 2;
-		unsigned long *new_addrs =
-			krealloc(report_filterlist.addrs,
-				 new_size * sizeof(unsigned long), GFP_ATOMIC);
-
-		if (new_addrs == NULL) {
-			/* leave filterlist itself untouched */
-			ret = -ENOMEM;
-			goto out;
+	raw_spin_lock_irqsave(&report_filterlist_lock, flags);
+	if (report_filterlist.used == report_filterlist.size) {
+		/* Check we pre-allocated enough, and retry if not. */
+		if (report_filterlist.used >= new_size) {
+			raw_spin_unlock_irqrestore(&report_filterlist_lock, flags);
+			kfree(new_addrs); /* kfree(NULL) is safe */
+			delay_free = new_addrs = NULL;
+			goto retry_alloc;
 		}
 
+		if (report_filterlist.used)
+			memcpy(new_addrs, report_filterlist.addrs, report_filterlist.used * sizeof(unsigned long));
+		delay_free = report_filterlist.addrs; /* free the old list */
+		report_filterlist.addrs = new_addrs;  /* switch to the new list */
 		report_filterlist.size = new_size;
-		report_filterlist.addrs = new_addrs;
 	}
 
 	/* Note: deduplicating should be done in userspace. */
@@ -185,9 +183,9 @@
 		kallsyms_lookup_name(func);
 	report_filterlist.sorted = false;
 
-out:
-	spin_unlock_irqrestore(&report_filterlist_lock, flags);
+	raw_spin_unlock_irqrestore(&report_filterlist_lock, flags);
 
+	kfree(delay_free);
 	return ret;
 }
 
@@ -204,13 +202,13 @@
 	}
 
 	/* show filter functions, and filter type */
-	spin_lock_irqsave(&report_filterlist_lock, flags);
+	raw_spin_lock_irqsave(&report_filterlist_lock, flags);
 	seq_printf(file, "\n%s functions: %s\n",
 		   report_filterlist.whitelist ? "whitelisted" : "blacklisted",
 		   report_filterlist.used == 0 ? "none" : "");
 	for (i = 0; i < report_filterlist.used; ++i)
 		seq_printf(file, " %ps\n", (void *)report_filterlist.addrs[i]);
-	spin_unlock_irqrestore(&report_filterlist_lock, flags);
+	raw_spin_unlock_irqrestore(&report_filterlist_lock, flags);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kcsan/kcsan_test.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kcsan/kcsan_test.c
@@ -151,7 +151,7 @@
 	const bool is_assert = (r->access[0].type | r->access[1].type) & KCSAN_ACCESS_ASSERT;
 	bool ret = false;
 	unsigned long flags;
-	typeof(observed.lines) expect;
+	typeof(*observed.lines) *expect;
 	const char *end;
 	char *cur;
 	int i;
@@ -160,6 +160,10 @@
 	if (!report_available())
 		return false;
 
+	expect = kmalloc(sizeof(observed.lines), GFP_KERNEL);
+	if (WARN_ON(!expect))
+		return false;
+
 	/* Generate expected report contents. */
 
 	/* Title */
@@ -243,6 +247,7 @@
 		strstr(observed.lines[2], expect[1])));
 out:
 	spin_unlock_irqrestore(&observed.lock, flags);
+	kfree(expect);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kcsan/report.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kcsan/report.c
@@ -432,8 +432,7 @@
 	dump_stack_print_info(KERN_DEFAULT);
 	pr_err("==================================================================\n");
 
-	if (panic_on_warn)
-		panic("panic_on_warn set ...\n");
+	check_panic_on_warn("KCSAN");
 }
 
 static void release_report(unsigned long *flags, struct other_info *other_info)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kexec.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kexec.c
@@ -93,13 +93,10 @@
 
 	/*
 	 * Because we write directly to the reserved memory region when loading
-	 * crash kernels we need a mutex here to prevent multiple crash kernels
-	 * from attempting to load simultaneously, and to prevent a crash kernel
-	 * from loading over the top of a in use crash kernel.
-	 *
-	 * KISS: always take the mutex.
+	 * crash kernels we need a serialization here to prevent multiple crash
+	 * kernels from attempting to load simultaneously.
 	 */
-	if (!mutex_trylock(&kexec_mutex))
+	if (!kexec_trylock())
 		return -EBUSY;
 
 	if (flags & KEXEC_ON_CRASH) {
@@ -165,7 +162,7 @@
 
 	kimage_free(image);
 out_unlock:
-	mutex_unlock(&kexec_mutex);
+	kexec_unlock();
 	return ret;
 }
 
@@ -243,7 +240,7 @@
 		((flags & KEXEC_ARCH_MASK) != KEXEC_ARCH_DEFAULT))
 		return -EINVAL;
 
-	ksegments = memdup_user(segments, nr_segments * sizeof(ksegments[0]));
+	ksegments = memdup_array_user(segments, nr_segments, sizeof(ksegments[0]));
 	if (IS_ERR(ksegments))
 		return PTR_ERR(ksegments);
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kexec_core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kexec_core.c
@@ -46,7 +46,7 @@
 #include <crypto/hash.h>
 #include "kexec_internal.h"
 
-DEFINE_MUTEX(kexec_mutex);
+atomic_t __kexec_lock = ATOMIC_INIT(0);
 
 /* Per cpu memory for storing cpu states in case of system crash. */
 note_buf_t __percpu *crash_notes;
@@ -944,7 +944,7 @@
  */
 void __noclone __crash_kexec(struct pt_regs *regs)
 {
-	/* Take the kexec_mutex here to prevent sys_kexec_load
+	/* Take the kexec_lock here to prevent sys_kexec_load
 	 * running on one cpu from replacing the crash kernel
 	 * we are using after a panic on a different cpu.
 	 *
@@ -952,7 +952,7 @@
 	 * of memory the xchg(&kexec_crash_image) would be
 	 * sufficient.  But since I reuse the memory...
 	 */
-	if (mutex_trylock(&kexec_mutex)) {
+	if (kexec_trylock()) {
 		if (kexec_crash_image) {
 			struct pt_regs fixed_regs;
 
@@ -961,7 +961,7 @@
 			machine_crash_shutdown(&fixed_regs);
 			machine_kexec(kexec_crash_image);
 		}
-		mutex_unlock(&kexec_mutex);
+		kexec_unlock();
 	}
 }
 STACK_FRAME_NON_STANDARD(__crash_kexec);
@@ -989,14 +989,17 @@
 	}
 }
 
-size_t crash_get_memory_size(void)
+ssize_t crash_get_memory_size(void)
 {
-	size_t size = 0;
+	ssize_t size = 0;
+
+	if (!kexec_trylock())
+		return -EBUSY;
 
-	mutex_lock(&kexec_mutex);
 	if (crashk_res.end != crashk_res.start)
 		size = resource_size(&crashk_res);
-	mutex_unlock(&kexec_mutex);
+
+	kexec_unlock();
 	return size;
 }
 
@@ -1016,7 +1019,8 @@
 	unsigned long old_size;
 	struct resource *ram_res;
 
-	mutex_lock(&kexec_mutex);
+	if (!kexec_trylock())
+		return -EBUSY;
 
 	if (kexec_crash_image) {
 		ret = -ENOENT;
@@ -1025,6 +1029,7 @@
 	start = crashk_res.start;
 	end = crashk_res.end;
 	old_size = (end == 0) ? 0 : end - start + 1;
+	new_size = roundup(new_size, KEXEC_CRASH_MEM_ALIGN);
 	if (new_size >= old_size) {
 		ret = (new_size == old_size) ? 0 : -EINVAL;
 		goto unlock;
@@ -1036,9 +1041,7 @@
 		goto unlock;
 	}
 
-	start = roundup(start, KEXEC_CRASH_MEM_ALIGN);
-	end = roundup(start + new_size, KEXEC_CRASH_MEM_ALIGN);
-
+	end = start + new_size;
 	crash_free_reserved_phys_range(end, crashk_res.end);
 
 	if ((start == end) && (crashk_res.parent != NULL))
@@ -1054,7 +1057,7 @@
 	insert_resource(&iomem_resource, ram_res);
 
 unlock:
-	mutex_unlock(&kexec_mutex);
+	kexec_unlock();
 	return ret;
 }
 
@@ -1126,7 +1129,7 @@
 {
 	int error = 0;
 
-	if (!mutex_trylock(&kexec_mutex))
+	if (!kexec_trylock())
 		return -EBUSY;
 	if (!kexec_image) {
 		error = -EINVAL;
@@ -1202,7 +1205,7 @@
 #endif
 
  Unlock:
-	mutex_unlock(&kexec_mutex);
+	kexec_unlock();
 	return error;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kexec_elf.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kexec_elf.c
@@ -390,7 +390,7 @@
 			 struct kexec_buf *kbuf,
 			 unsigned long *lowest_load_addr)
 {
-	unsigned long lowest_addr = UINT_MAX;
+	unsigned long lowest_addr = ULONG_MAX;
 	int ret;
 	size_t i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kexec_file.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kexec_file.c
@@ -29,6 +29,15 @@
 #include <linux/vmalloc.h>
 #include "kexec_internal.h"
 
+#ifdef CONFIG_KEXEC_SIG
+static bool sig_enforce = IS_ENABLED(CONFIG_KEXEC_SIG_FORCE);
+
+void set_kexec_sig_enforced(void)
+{
+	sig_enforce = true;
+}
+#endif
+
 static int kexec_calculate_store_digests(struct kimage *image);
 
 /*
@@ -109,40 +118,6 @@
 #endif
 
 /*
- * arch_kexec_apply_relocations_add - apply relocations of type RELA
- * @pi:		Purgatory to be relocated.
- * @section:	Section relocations applying to.
- * @relsec:	Section containing RELAs.
- * @symtab:	Corresponding symtab.
- *
- * Return: 0 on success, negative errno on error.
- */
-int __weak
-arch_kexec_apply_relocations_add(struct purgatory_info *pi, Elf_Shdr *section,
-				 const Elf_Shdr *relsec, const Elf_Shdr *symtab)
-{
-	pr_err("RELA relocation unsupported.\n");
-	return -ENOEXEC;
-}
-
-/*
- * arch_kexec_apply_relocations - apply relocations of type REL
- * @pi:		Purgatory to be relocated.
- * @section:	Section relocations applying to.
- * @relsec:	Section containing RELs.
- * @symtab:	Corresponding symtab.
- *
- * Return: 0 on success, negative errno on error.
- */
-int __weak
-arch_kexec_apply_relocations(struct purgatory_info *pi, Elf_Shdr *section,
-			     const Elf_Shdr *relsec, const Elf_Shdr *symtab)
-{
-	pr_err("REL relocation unsupported.\n");
-	return -ENOEXEC;
-}
-
-/*
  * Free up memory used by kernel, initrd, and command line. This is temporary
  * memory allocation which is not needed any more after these buffers have
  * been loaded into separate segments and have been copied elsewhere.
@@ -184,6 +159,23 @@
 }
 
 #ifdef CONFIG_KEXEC_SIG
+#ifdef CONFIG_SIGNED_PE_FILE_VERIFICATION
+int kexec_kernel_verify_pe_sig(const char *kernel, unsigned long kernel_len)
+{
+	int ret;
+
+	ret = verify_pefile_signature(kernel, kernel_len,
+				      VERIFY_USE_SECONDARY_KEYRING,
+				      VERIFYING_KEXEC_PE_SIGNATURE);
+	if (ret == -ENOKEY && IS_ENABLED(CONFIG_INTEGRITY_PLATFORM_KEYRING)) {
+		ret = verify_pefile_signature(kernel, kernel_len,
+					      VERIFY_USE_PLATFORM_KEYRING,
+					      VERIFYING_KEXEC_PE_SIGNATURE);
+	}
+	return ret;
+}
+#endif
+
 static int
 kimage_validate_signature(struct kimage *image)
 {
@@ -193,7 +185,7 @@
 					   image->kernel_buf_len);
 	if (ret) {
 
-		if (IS_ENABLED(CONFIG_KEXEC_SIG_FORCE)) {
+		if (sig_enforce) {
 			pr_notice("Enforced kernel signature verification failed (%d).\n", ret);
 			return ret;
 		}
@@ -368,7 +360,7 @@
 
 	image = NULL;
 
-	if (!mutex_trylock(&kexec_mutex))
+	if (!kexec_trylock())
 		return -EBUSY;
 
 	dest_image = &kexec_image;
@@ -440,7 +432,7 @@
 	if ((flags & KEXEC_FILE_ON_CRASH) && kexec_crash_image)
 		arch_kexec_protect_crashkres();
 
-	mutex_unlock(&kexec_mutex);
+	kexec_unlock();
 	kimage_free(image);
 	return ret;
 }
@@ -935,10 +927,22 @@
 		}
 
 		offset = ALIGN(offset, align);
+
+		/*
+		 * Check if the segment contains the entry point, if so,
+		 * calculate the value of image->start based on it.
+		 * If the compiler has produced more than one .text section
+		 * (Eg: .text.hot), they are generally after the main .text
+		 * section, and they shall not be used to calculate
+		 * image->start. So do not re-calculate image->start if it
+		 * is not set to the initial value, and warn the user so they
+		 * have a chance to fix their purgatory's linker script.
+		 */
 		if (sechdrs[i].sh_flags & SHF_EXECINSTR &&
 		    pi->ehdr->e_entry >= sechdrs[i].sh_addr &&
 		    pi->ehdr->e_entry < (sechdrs[i].sh_addr
-					 + sechdrs[i].sh_size)) {
+					 + sechdrs[i].sh_size) &&
+		    !WARN_ON(kbuf->image->start != pi->ehdr->e_entry)) {
 			kbuf->image->start -= sechdrs[i].sh_addr;
 			kbuf->image->start += kbuf->mem + offset;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kexec_internal.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/kexec_internal.h
@@ -13,7 +13,20 @@
 int kimage_is_destination_range(struct kimage *image,
 				unsigned long start, unsigned long end);
 
-extern struct mutex kexec_mutex;
+/*
+ * Whatever is used to serialize accesses to the kexec_crash_image needs to be
+ * NMI safe, as __crash_kexec() can happen during nmi_panic(), so here we use a
+ * "simple" atomic variable that is acquired with a cmpxchg().
+ */
+extern atomic_t __kexec_lock;
+static inline bool kexec_trylock(void)
+{
+	return atomic_cmpxchg_acquire(&__kexec_lock, 0, 1) == 0;
+}
+static inline void kexec_unlock(void)
+{
+	atomic_set_release(&__kexec_lock, 0);
+}
 
 #ifdef CONFIG_KEXEC_FILE
 #include <linux/purgatory.h>
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kheaders.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kheaders.c
@@ -26,15 +26,15 @@
 "	.popsection				\n"
 );
 
-extern char kernel_headers_data;
-extern char kernel_headers_data_end;
+extern char kernel_headers_data[];
+extern char kernel_headers_data_end[];
 
 static ssize_t
 ikheaders_read(struct file *file,  struct kobject *kobj,
 	       struct bin_attribute *bin_attr,
 	       char *buf, loff_t off, size_t len)
 {
-	memcpy(buf, &kernel_headers_data + off, len);
+	memcpy(buf, &kernel_headers_data[off], len);
 	return len;
 }
 
@@ -48,8 +48,8 @@
 
 static int __init ikheaders_init(void)
 {
-	kheaders_attr.size = (&kernel_headers_data_end -
-			      &kernel_headers_data);
+	kheaders_attr.size = (kernel_headers_data_end -
+			      kernel_headers_data);
 	return sysfs_create_bin_file(kernel_kobj, &kheaders_attr);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kprobes.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kprobes.c
@@ -18,6 +18,9 @@
  *		<jkenisto@us.ibm.com> and Prasanna S Panchamukhi
  *		<prasanna@in.ibm.com> added function-return probes.
  */
+
+#define pr_fmt(fmt) "kprobes: " fmt
+
 #include <linux/kprobes.h>
 #include <linux/hash.h>
 #include <linux/init.h>
@@ -448,8 +451,8 @@
 	return 0;
 }
 
-/* Return true(!0) if the kprobe is disarmed. Note: p must be on hash list */
-static inline int kprobe_disarmed(struct kprobe *p)
+/* Return true if the kprobe is disarmed. Note: p must be on hash list */
+bool kprobe_disarmed(struct kprobe *p)
 {
 	struct optimized_kprobe *op;
 
@@ -546,17 +549,15 @@
 	/* See comment in do_optimize_kprobes() */
 	lockdep_assert_cpus_held();
 
-	/* Unoptimization must be done anytime */
-	if (list_empty(&unoptimizing_list))
-		return;
+	if (!list_empty(&unoptimizing_list))
+		arch_unoptimize_kprobes(&unoptimizing_list, &freeing_list);
 
-	arch_unoptimize_kprobes(&unoptimizing_list, &freeing_list);
-	/* Loop free_list for disarming */
+	/* Loop on 'freeing_list' for disarming and removing from kprobe hash list */
 	list_for_each_entry_safe(op, tmp, &freeing_list, list) {
 		/* Switching from detour code to origin */
 		op->kp.flags &= ~KPROBE_FLAG_OPTIMIZED;
-		/* Disarm probes if marked disabled */
-		if (kprobe_disabled(&op->kp))
+		/* Disarm probes if marked disabled and not gone */
+		if (kprobe_disabled(&op->kp) && !kprobe_gone(&op->kp))
 			arch_disarm_kprobe(&op->kp);
 		if (kprobe_unused(&op->kp)) {
 			/*
@@ -653,7 +654,7 @@
 	mutex_unlock(&kprobe_mutex);
 }
 
-static bool optprobe_queued_unopt(struct optimized_kprobe *op)
+bool optprobe_queued_unopt(struct optimized_kprobe *op)
 {
 	struct optimized_kprobe *_op;
 
@@ -785,14 +786,13 @@
 	op->kp.flags &= ~KPROBE_FLAG_OPTIMIZED;
 
 	if (kprobe_unused(p)) {
-		/* Enqueue if it is unused */
-		list_add(&op->list, &freeing_list);
 		/*
-		 * Remove unused probes from the hash list. After waiting
-		 * for synchronization, this probe is reclaimed.
-		 * (reclaiming is done by do_free_cleaned_kprobes().)
+		 * Unused kprobe is on unoptimizing or freeing list. We move it
+		 * to freeing_list and let the kprobe_optimizer() remove it from
+		 * the kprobe hash list and free it.
 		 */
-		hlist_del_rcu(&op->kp.hlist);
+		if (optprobe_queued_unopt(op))
+			list_move(&op->list, &freeing_list);
 	}
 
 	/* Don't touch the code, because it is already freed. */
@@ -892,7 +892,7 @@
 				optimize_kprobe(p);
 	}
 	cpus_read_unlock();
-	printk(KERN_INFO "Kprobes globally optimized\n");
+	pr_info("kprobe jump-optimization is enabled. All kprobes are optimized if possible.\n");
 out:
 	mutex_unlock(&kprobe_mutex);
 }
@@ -925,7 +925,7 @@
 
 	/* Wait for unoptimizing completion */
 	wait_for_kprobe_optimizer();
-	printk(KERN_INFO "Kprobes globally unoptimized\n");
+	pr_info("kprobe jump-optimization is disabled. All kprobes are based on software breakpoint.\n");
 }
 
 static DEFINE_MUTEX(kprobe_sysctl_mutex);
@@ -1003,7 +1003,7 @@
 	 * unregistered.
 	 * Thus there should be no chance to reuse unused kprobe.
 	 */
-	printk(KERN_ERR "Error: There should be no unused kprobe here.\n");
+	WARN_ON_ONCE(1);
 	return -EINVAL;
 }
 
@@ -1049,18 +1049,13 @@
 	int ret = 0;
 
 	ret = ftrace_set_filter_ip(ops, (unsigned long)p->addr, 0, 0);
-	if (ret) {
-		pr_debug("Failed to arm kprobe-ftrace at %pS (%d)\n",
-			 p->addr, ret);
+	if (WARN_ONCE(ret < 0, "Failed to arm kprobe-ftrace at %pS (error %d)\n", p->addr, ret))
 		return ret;
-	}
 
 	if (*cnt == 0) {
 		ret = register_ftrace_function(ops);
-		if (ret) {
-			pr_debug("Failed to init kprobe-ftrace (%d)\n", ret);
+		if (WARN(ret < 0, "Failed to register kprobe-ftrace (error %d)\n", ret))
 			goto err_ftrace;
-		}
 	}
 
 	(*cnt)++;
@@ -1092,14 +1087,14 @@
 
 	if (*cnt == 1) {
 		ret = unregister_ftrace_function(ops);
-		if (WARN(ret < 0, "Failed to unregister kprobe-ftrace (%d)\n", ret))
+		if (WARN(ret < 0, "Failed to unregister kprobe-ftrace (error %d)\n", ret))
 			return ret;
 	}
 
 	(*cnt)--;
 
 	ret = ftrace_set_filter_ip(ops, (unsigned long)p->addr, 1, 0);
-	WARN_ONCE(ret < 0, "Failed to disarm kprobe-ftrace at %pS (%d)\n",
+	WARN_ONCE(ret < 0, "Failed to disarm kprobe-ftrace at %pS (error %d)\n",
 		  p->addr, ret);
 	return ret;
 }
@@ -1531,14 +1526,10 @@
 
 int __weak arch_check_ftrace_location(struct kprobe *p)
 {
-	unsigned long ftrace_addr;
+	unsigned long addr = (unsigned long)p->addr;
 
-	ftrace_addr = ftrace_location((unsigned long)p->addr);
-	if (ftrace_addr) {
+	if (ftrace_location(addr) == addr) {
 #ifdef CONFIG_KPROBES_ON_FTRACE
-		/* Given address is not on the instruction boundary */
-		if ((unsigned long)p->addr != ftrace_addr)
-			return -EILSEQ;
 		p->flags |= KPROBE_FLAG_FTRACE;
 #else	/* !CONFIG_KPROBES_ON_FTRACE */
 		return -EINVAL;
@@ -1547,6 +1538,17 @@
 	return 0;
 }
 
+static bool is_cfi_preamble_symbol(unsigned long addr)
+{
+	char symbuf[KSYM_NAME_LEN];
+
+	if (lookup_symbol_name(addr, symbuf))
+		return false;
+
+	return str_has_prefix(symbuf, "__cfi_") ||
+		str_has_prefix(symbuf, "__pfx_");
+}
+
 static int check_kprobe_address_safe(struct kprobe *p,
 				     struct module **probed_mod)
 {
@@ -1558,18 +1560,27 @@
 	jump_label_lock();
 	preempt_disable();
 
-	/* Ensure it is not in reserved area nor out of text */
-	if (!kernel_text_address((unsigned long) p->addr) ||
+	/* Ensure the address is in a text area, and find a module if exists. */
+	*probed_mod = NULL;
+	if (!core_kernel_text((unsigned long) p->addr)) {
+		*probed_mod = __module_text_address((unsigned long) p->addr);
+		if (!(*probed_mod)) {
+			ret = -EINVAL;
+			goto out;
+		}
+	}
+	/* Ensure it is not in reserved area. */
+	if (in_gate_area_no_mm((unsigned long) p->addr) ||
 	    within_kprobe_blacklist((unsigned long) p->addr) ||
 	    jump_label_text_reserved(p->addr, p->addr) ||
 	    static_call_text_reserved(p->addr, p->addr) ||
-	    find_bug((unsigned long)p->addr)) {
+	    find_bug((unsigned long)p->addr) ||
+	    is_cfi_preamble_symbol((unsigned long)p->addr)) {
 		ret = -EINVAL;
 		goto out;
 	}
 
-	/* Check if are we probing a module */
-	*probed_mod = __module_text_address((unsigned long) p->addr);
+	/* Get module refcount and reject __init functions for loaded modules. */
 	if (*probed_mod) {
 		/*
 		 * We must hold a refcount of the probed module while updating
@@ -1704,11 +1715,12 @@
 		/* Try to disarm and disable this/parent probe */
 		if (p == orig_p || aggr_kprobe_disabled(orig_p)) {
 			/*
-			 * If kprobes_all_disarmed is set, orig_p
-			 * should have already been disarmed, so
-			 * skip unneed disarming process.
+			 * Don't be lazy here.  Even if 'kprobes_all_disarmed'
+			 * is false, 'orig_p' might not have been armed yet.
+			 * Note arm_all_kprobes() __tries__ to arm all kprobes
+			 * on the best effort basis.
 			 */
-			if (!kprobes_all_disarmed) {
+			if (!kprobes_all_disarmed && !kprobe_disabled(orig_p)) {
 				ret = disarm_kprobe(orig_p, true);
 				if (ret) {
 					p->flags &= ~KPROBE_FLAG_DISABLED;
@@ -1757,7 +1769,13 @@
 				if ((list_p != p) && (list_p->post_handler))
 					goto noclean;
 			}
-			ap->post_handler = NULL;
+			/*
+			 * For the kprobe-on-ftrace case, we keep the
+			 * post_handler setting to identify this aggrprobe
+			 * armed with kprobe_ipmodify_ops.
+			 */
+			if (!kprobe_ftrace(ap))
+				ap->post_handler = NULL;
 		}
 noclean:
 		/*
@@ -1857,46 +1875,87 @@
 
 #ifdef CONFIG_KRETPROBES
 
-unsigned long __kretprobe_trampoline_handler(struct pt_regs *regs,
-					     void *trampoline_address,
-					     void *frame_pointer)
+/* This assumes the 'tsk' is the current task or the is not running. */
+static kprobe_opcode_t *__kretprobe_find_ret_addr(struct task_struct *tsk,
+						  struct llist_node **cur)
 {
-	kprobe_opcode_t *correct_ret_addr = NULL;
 	struct kretprobe_instance *ri = NULL;
-	struct llist_node *first, *node;
-	struct kretprobe *rp;
+	struct llist_node *node = *cur;
+
+	if (!node)
+		node = tsk->kretprobe_instances.first;
+	else
+		node = node->next;
 
-	/* Find all nodes for this frame. */
-	first = node = current->kretprobe_instances.first;
 	while (node) {
 		ri = container_of(node, struct kretprobe_instance, llist);
-
-		BUG_ON(ri->fp != frame_pointer);
-
-		if (ri->ret_addr != trampoline_address) {
-			correct_ret_addr = ri->ret_addr;
-			/*
-			 * This is the real return address. Any other
-			 * instances associated with this task are for
-			 * other calls deeper on the call stack
-			 */
-			goto found;
+		if (ri->ret_addr != kretprobe_trampoline_addr()) {
+			*cur = node;
+			return ri->ret_addr;
 		}
-
 		node = node->next;
 	}
-	pr_err("Oops! Kretprobe fails to find correct return address.\n");
-	BUG_ON(1);
+	return NULL;
+}
+NOKPROBE_SYMBOL(__kretprobe_find_ret_addr);
 
-found:
-	/* Unlink all nodes for this frame. */
-	current->kretprobe_instances.first = node->next;
-	node->next = NULL;
+/**
+ * kretprobe_find_ret_addr -- Find correct return address modified by kretprobe
+ * @tsk: Target task
+ * @fp: A frame pointer
+ * @cur: a storage of the loop cursor llist_node pointer for next call
+ *
+ * Find the correct return address modified by a kretprobe on @tsk in unsigned
+ * long type. If it finds the return address, this returns that address value,
+ * or this returns 0.
+ * The @tsk must be 'current' or a task which is not running. @fp is a hint
+ * to get the currect return address - which is compared with the
+ * kretprobe_instance::fp field. The @cur is a loop cursor for searching the
+ * kretprobe return addresses on the @tsk. The '*@cur' should be NULL at the
+ * first call, but '@cur' itself must NOT NULL.
+ */
+unsigned long kretprobe_find_ret_addr(struct task_struct *tsk, void *fp,
+				      struct llist_node **cur)
+{
+	struct kretprobe_instance *ri = NULL;
+	kprobe_opcode_t *ret;
+
+	if (WARN_ON_ONCE(!cur))
+		return 0;
+
+	do {
+		ret = __kretprobe_find_ret_addr(tsk, cur);
+		if (!ret)
+			break;
+		ri = container_of(*cur, struct kretprobe_instance, llist);
+	} while (ri->fp != fp);
+
+	return (unsigned long)ret;
+}
+NOKPROBE_SYMBOL(kretprobe_find_ret_addr);
+
+unsigned long __kretprobe_trampoline_handler(struct pt_regs *regs,
+					     void *frame_pointer)
+{
+	kprobe_opcode_t *correct_ret_addr = NULL;
+	struct kretprobe_instance *ri = NULL;
+	struct llist_node *first, *node = NULL;
+	struct kretprobe *rp;
+
+	/* Find correct address and all nodes for this frame. */
+	correct_ret_addr = __kretprobe_find_ret_addr(current, &node);
+	if (!correct_ret_addr) {
+		pr_err("kretprobe: Return address not found, not execute handler. Maybe there is a bug in the kernel.\n");
+		BUG_ON(1);
+	}
 
-	/* Run them..  */
+	/* Run the user handler of the nodes. */
+	first = current->kretprobe_instances.first;
 	while (first) {
 		ri = container_of(first, struct kretprobe_instance, llist);
-		first = first->next;
+
+		if (WARN_ON_ONCE(ri->fp != frame_pointer))
+			break;
 
 		rp = get_kretprobe(ri);
 		if (rp && rp->handler) {
@@ -1907,6 +1966,21 @@
 			rp->handler(ri, regs);
 			__this_cpu_write(current_kprobe, prev);
 		}
+		if (first == node)
+			break;
+
+		first = first->next;
+	}
+
+	/* Unlink all nodes for this frame. */
+	first = current->kretprobe_instances.first;
+	current->kretprobe_instances.first = node->next;
+	node->next = NULL;
+
+	/* Recycle free instances. */
+	while (first) {
+		ri = container_of(first, struct kretprobe_instance, llist);
+		first = first->next;
 
 		recycle_rp_inst(ri);
 	}
@@ -2006,6 +2080,9 @@
 		}
 	}
 
+	if (rp->data_size > KRETPROBE_MAX_DATA_SIZE)
+		return -E2BIG;
+
 	rp->kp.pre_handler = pre_handler_kretprobe;
 	rp->kp.post_handler = NULL;
 
@@ -2022,7 +2099,7 @@
 	if (!rp->rph)
 		return -ENOMEM;
 
-	rp->rph->rp = rp;
+	rcu_assign_pointer(rp->rph->rp, rp);
 	for (i = 0; i < rp->maxactive; i++) {
 		inst = kzalloc(sizeof(struct kretprobe_instance) +
 			       rp->data_size, GFP_KERNEL);
@@ -2079,7 +2156,7 @@
 	for (i = 0; i < num; i++) {
 		if (__unregister_kprobe_top(&rps[i]->kp) < 0)
 			rps[i]->kp.addr = NULL;
-		rps[i]->rph->rp = NULL;
+		rcu_assign_pointer(rps[i]->rph->rp, NULL);
 	}
 	mutex_unlock(&kprobe_mutex);
 
@@ -2202,8 +2279,11 @@
 	if (!kprobes_all_disarmed && kprobe_disabled(p)) {
 		p->flags &= ~KPROBE_FLAG_DISABLED;
 		ret = arm_kprobe(p);
-		if (ret)
+		if (ret) {
 			p->flags |= KPROBE_FLAG_DISABLED;
+			if (p != kp)
+				kp->flags |= KPROBE_FLAG_DISABLED;
+		}
 	}
 out:
 	mutex_unlock(&kprobe_mutex);
@@ -2214,8 +2294,7 @@
 /* Caller must NOT call this in usual path. This is only for critical case */
 void dump_kprobe(struct kprobe *kp)
 {
-	pr_err("Dumping kprobe:\n");
-	pr_err("Name: %s\nOffset: %x\nAddress: %pS\n",
+	pr_err("Dump kprobe:\n.symbol_name = %s, .offset = %x, .addr = %pS\n",
 	       kp->symbol_name, kp->offset, kp->addr);
 }
 NOKPROBE_SYMBOL(dump_kprobe);
@@ -2478,8 +2557,7 @@
 	err = populate_kprobe_blacklist(__start_kprobe_blacklist,
 					__stop_kprobe_blacklist);
 	if (err) {
-		pr_err("kprobes: failed to populate blacklist: %d\n", err);
-		pr_err("Please take care of using kprobes.\n");
+		pr_err("Failed to populate blacklist (error %d), kprobes not restricted, be careful using them!\n", err);
 	}
 
 	if (kretprobe_blacklist_size) {
@@ -2488,7 +2566,7 @@
 			kretprobe_blacklist[i].addr =
 				kprobe_lookup_name(kretprobe_blacklist[i].name, 0);
 			if (!kretprobe_blacklist[i].addr)
-				printk("kretprobe: lookup failed: %s\n",
+				pr_err("Failed to lookup symbol '%s' for kretprobe blacklist. Maybe the target function is removed or renamed.\n",
 				       kretprobe_blacklist[i].name);
 		}
 	}
@@ -2692,7 +2770,7 @@
 	}
 
 	if (errors)
-		pr_warn("Kprobes globally enabled, but failed to arm %d out of %d probes\n",
+		pr_warn("Kprobes globally enabled, but failed to enable %d out of %d probes. Please check which kprobes are kept disabled via debugfs.\n",
 			errors, total);
 	else
 		pr_info("Kprobes globally enabled\n");
@@ -2735,7 +2813,7 @@
 	}
 
 	if (errors)
-		pr_warn("Kprobes globally disabled, but failed to disarm %d out of %d probes\n",
+		pr_warn("Kprobes globally disabled, but failed to disable %d out of %d probes. Please check which kprobes are kept enabled via debugfs.\n",
 			errors, total);
 	else
 		pr_info("Kprobes globally disabled\n");
@@ -2809,13 +2887,12 @@
 static int __init debugfs_kprobe_init(void)
 {
 	struct dentry *dir;
-	unsigned int value = 1;
 
 	dir = debugfs_create_dir("kprobes", NULL);
 
 	debugfs_create_file("list", 0400, dir, NULL, &kprobes_fops);
 
-	debugfs_create_file("enabled", 0600, dir, &value, &fops_kp);
+	debugfs_create_file("enabled", 0600, dir, NULL, &fops_kp);
 
 	debugfs_create_file("blacklist", 0400, dir, NULL,
 			    &kprobe_blacklist_fops);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/ksysfs.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/ksysfs.c
@@ -106,7 +106,12 @@
 static ssize_t kexec_crash_size_show(struct kobject *kobj,
 				       struct kobj_attribute *attr, char *buf)
 {
-	return sprintf(buf, "%zu\n", crash_get_memory_size());
+	ssize_t size = crash_get_memory_size();
+
+	if (size < 0)
+		return size;
+
+	return sprintf(buf, "%zd\n", size);
 }
 static ssize_t kexec_crash_size_store(struct kobject *kobj,
 				   struct kobj_attribute *attr,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/kthread.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/kthread.c
@@ -268,6 +268,21 @@
 }
 EXPORT_SYMBOL_GPL(kthread_parkme);
 
+/**
+ * kthread_exit - Cause the current kthread return @result to kthread_stop().
+ * @result: The integer value to return to kthread_stop().
+ *
+ * While kthread_exit can be called directly, it exists so that
+ * functions which do some additional work in non-modular code such as
+ * module_put_and_kthread_exit can be implemented.
+ *
+ * Does not return.
+ */
+void __noreturn kthread_exit(long result)
+{
+	do_exit(result);
+}
+
 static int kthread(void *_create)
 {
 	/* Copy data: it's on kthread's stack */
@@ -285,13 +300,13 @@
 	done = xchg(&create->done, NULL);
 	if (!done) {
 		kfree(create);
-		do_exit(-EINTR);
+		kthread_exit(-EINTR);
 	}
 
 	if (!self) {
 		create->result = ERR_PTR(-ENOMEM);
 		complete(done);
-		do_exit(-ENOMEM);
+		kthread_exit(-ENOMEM);
 	}
 
 	self->threadfn = threadfn;
@@ -318,7 +333,7 @@
 		__kthread_parkme(self);
 		ret = threadfn(data);
 	}
-	do_exit(ret);
+	kthread_exit(ret);
 }
 
 /* called from kernel_clone() to get node information for about to be created task */
@@ -382,6 +397,17 @@
 	 * new kernel thread.
 	 */
 	if (unlikely(wait_for_completion_killable(&done))) {
+		int i = 0;
+
+		/*
+		 * I got SIGKILL, but wait for 10 more seconds for completion
+		 * unless chosen by the OOM killer. This delay is there as a
+		 * workaround for boot failure caused by SIGKILL upon device
+		 * driver initialization timeout.
+		 */
+		while (i++ < 10 && !test_tsk_thread_flag(current, TIF_MEMDIE))
+			if (wait_for_completion_timeout(&done, HZ))
+				goto ready;
 		/*
 		 * If I was SIGKILLed before kthreadd (or new kernel thread)
 		 * calls complete(), leave the cleanup of this structure to
@@ -395,6 +421,7 @@
 		 */
 		wait_for_completion(&done);
 	}
+ready:
 	task = create->result;
 	if (!IS_ERR(task)) {
 		static const struct sched_param param = { .sched_priority = 0 };
@@ -523,6 +550,7 @@
 	to_kthread(p)->cpu = cpu;
 	return p;
 }
+EXPORT_SYMBOL(kthread_create_on_cpu);
 
 void kthread_set_per_cpu(struct task_struct *k, int cpu)
 {
@@ -562,6 +590,8 @@
 {
 	struct kthread *kthread = to_kthread(k);
 
+	if (!test_bit(KTHREAD_SHOULD_PARK, &kthread->flags))
+		return;
 	/*
 	 * Newly created kthread was parked when the CPU was offline.
 	 * The binding was lost and we need to set it again.
@@ -627,7 +657,7 @@
  * instead of calling wake_up_process(): the thread will exit without
  * calling threadfn().
  *
- * If threadfn() may call do_exit() itself, the caller must ensure
+ * If threadfn() may call kthread_exit() itself, the caller must ensure
  * task_struct can't go away.
  *
  * Returns the result of threadfn(), or %-EINTR if wake_up_process()
@@ -765,8 +795,16 @@
 		 * event only cares about the address.
 		 */
 		trace_sched_kthread_work_execute_end(work, func);
-	} else if (!freezing(current))
+	} else if (!freezing(current)) {
 		schedule();
+	} else {
+		/*
+		 * Handle the case where the current remains
+		 * TASK_INTERRUPTIBLE. try_to_freeze() expects
+		 * the current to be TASK_RUNNING.
+		 */
+		__set_current_state(TASK_RUNNING);
+	}
 
 	try_to_freeze();
 	cond_resched();
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/livepatch/core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/livepatch/core.c
@@ -190,7 +190,7 @@
 	return -EINVAL;
 }
 
-static int klp_resolve_symbols(Elf64_Shdr *sechdrs, const char *strtab,
+static int klp_resolve_symbols(Elf_Shdr *sechdrs, const char *strtab,
 			       unsigned int symndx, Elf_Shdr *relasec,
 			       const char *sec_objname)
 {
@@ -218,7 +218,7 @@
 	relas = (Elf_Rela *) relasec->sh_addr;
 	/* For each rela in this klp relocation section */
 	for (i = 0; i < relasec->sh_size / sizeof(Elf_Rela); i++) {
-		sym = (Elf64_Sym *)sechdrs[symndx].sh_addr + ELF_R_SYM(relas[i].r_info);
+		sym = (Elf_Sym *)sechdrs[symndx].sh_addr + ELF_R_SYM(relas[i].r_info);
 		if (sym->st_shndx != SHN_LIVEPATCH) {
 			pr_err("symbol %s is not marked as a livepatch symbol\n",
 			       strtab + sym->st_name);
@@ -244,7 +244,7 @@
 		 * symbols are exported and normal relas can be used instead.
 		 */
 		if (!sec_vmlinux && sym_vmlinux) {
-			pr_err("invalid access to vmlinux symbol '%s' from module-specific livepatch relocation section",
+			pr_err("invalid access to vmlinux symbol '%s' from module-specific livepatch relocation section\n",
 			       sym_name);
 			return -EINVAL;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/livepatch/transition.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/livepatch/transition.c
@@ -13,7 +13,6 @@
 #include "core.h"
 #include "patch.h"
 #include "transition.h"
-#include "../sched/sched.h"
 
 #define MAX_STACK_ENTRIES  100
 #define STACK_ERR_BUF_SIZE 128
@@ -240,7 +239,7 @@
  * Determine whether it's safe to transition the task to the target patch state
  * by looking for any to-be-patched or to-be-unpatched functions on its stack.
  */
-static int klp_check_stack(struct task_struct *task, char *err_buf)
+static int klp_check_stack(struct task_struct *task, const char **oldname)
 {
 	static unsigned long entries[MAX_STACK_ENTRIES];
 	struct klp_object *obj;
@@ -248,12 +247,8 @@
 	int ret, nr_entries;
 
 	ret = stack_trace_save_tsk_reliable(task, entries, ARRAY_SIZE(entries));
-	if (ret < 0) {
-		snprintf(err_buf, STACK_ERR_BUF_SIZE,
-			 "%s: %s:%d has an unreliable stack\n",
-			 __func__, task->comm, task->pid);
-		return ret;
-	}
+	if (ret < 0)
+		return -EINVAL;
 	nr_entries = ret;
 
 	klp_for_each_object(klp_transition_patch, obj) {
@@ -262,11 +257,8 @@
 		klp_for_each_func(obj, func) {
 			ret = klp_check_stack_func(func, entries, nr_entries);
 			if (ret) {
-				snprintf(err_buf, STACK_ERR_BUF_SIZE,
-					 "%s: %s:%d is sleeping on function %s\n",
-					 __func__, task->comm, task->pid,
-					 func->old_name);
-				return ret;
+				*oldname = func->old_name;
+				return -EADDRINUSE;
 			}
 		}
 	}
@@ -274,6 +266,22 @@
 	return 0;
 }
 
+static int klp_check_and_switch_task(struct task_struct *task, void *arg)
+{
+	int ret;
+
+	if (task_curr(task) && task != current)
+		return -EBUSY;
+
+	ret = klp_check_stack(task, arg);
+	if (ret)
+		return ret;
+
+	clear_tsk_thread_flag(task, TIF_PATCH_PENDING);
+	task->patch_state = klp_target_state;
+	return 0;
+}
+
 /*
  * Try to safely switch a task to the target patch state.  If it's currently
  * running, or it's sleeping on a to-be-patched or to-be-unpatched function, or
@@ -281,13 +289,8 @@
  */
 static bool klp_try_switch_task(struct task_struct *task)
 {
-	static char err_buf[STACK_ERR_BUF_SIZE];
-	struct rq *rq;
-	struct rq_flags flags;
+	const char *old_name;
 	int ret;
-	bool success = false;
-
-	err_buf[0] = '\0';
 
 	/* check if this task has already switched over */
 	if (task->patch_state == klp_target_state)
@@ -305,36 +308,31 @@
 	 * functions.  If all goes well, switch the task to the target patch
 	 * state.
 	 */
-	rq = task_rq_lock(task, &flags);
+	ret = task_call_func(task, klp_check_and_switch_task, &old_name);
+	switch (ret) {
+	case 0:		/* success */
+		break;
 
-	if (task_running(rq, task) && task != current) {
-		snprintf(err_buf, STACK_ERR_BUF_SIZE,
-			 "%s: %s:%d is running\n", __func__, task->comm,
-			 task->pid);
-		goto done;
+	case -EBUSY:	/* klp_check_and_switch_task() */
+		pr_debug("%s: %s:%d is running\n",
+			 __func__, task->comm, task->pid);
+		break;
+	case -EINVAL:	/* klp_check_and_switch_task() */
+		pr_debug("%s: %s:%d has an unreliable stack\n",
+			 __func__, task->comm, task->pid);
+		break;
+	case -EADDRINUSE: /* klp_check_and_switch_task() */
+		pr_debug("%s: %s:%d is sleeping on function %s\n",
+			 __func__, task->comm, task->pid, old_name);
+		break;
+
+	default:
+		pr_debug("%s: Unknown error code (%d) when trying to switch %s:%d\n",
+			 __func__, ret, task->comm, task->pid);
+		break;
 	}
 
-	ret = klp_check_stack(task, err_buf);
-	if (ret)
-		goto done;
-
-	success = true;
-
-	clear_tsk_thread_flag(task, TIF_PATCH_PENDING);
-	task->patch_state = klp_target_state;
-
-done:
-	task_rq_unlock(rq, task, &flags);
-
-	/*
-	 * Due to console deadlock issues, pr_debug() can't be used while
-	 * holding the task rq lock.  Instead we have to use a temporary buffer
-	 * and print the debug message after releasing the lock.
-	 */
-	if (err_buf[0] != '\0')
-		pr_debug("%s", err_buf);
-
-	return success;
+	return !ret;
 }
 
 /*
@@ -415,8 +413,11 @@
 	for_each_possible_cpu(cpu) {
 		task = idle_task(cpu);
 		if (cpu_online(cpu)) {
-			if (!klp_try_switch_task(task))
+			if (!klp_try_switch_task(task)) {
 				complete = false;
+				/* Make idle task go through the main loop. */
+				wake_up_if_idle(cpu);
+			}
 		} else if (task->patch_state != klp_target_state) {
 			/* offline idle tasks can be switched immediately */
 			clear_tsk_thread_flag(task, TIF_PATCH_PENDING);
@@ -610,9 +611,23 @@
 /* Called from copy_process() during fork */
 void klp_copy_process(struct task_struct *child)
 {
-	child->patch_state = current->patch_state;
 
-	/* TIF_PATCH_PENDING gets copied in setup_thread_stack() */
+	/*
+	 * The parent process may have gone through a KLP transition since
+	 * the thread flag was copied in setup_thread_stack earlier. Bring
+	 * the task flag up to date with the parent here.
+	 *
+	 * The operation is serialized against all klp_*_transition()
+	 * operations by the tasklist_lock. The only exception is
+	 * klp_update_patch_state(current), but we cannot race with
+	 * that because we are current.
+	 */
+	if (test_tsk_thread_flag(current, TIF_PATCH_PENDING))
+		set_tsk_thread_flag(child, TIF_PATCH_PENDING);
+	else
+		clear_tsk_thread_flag(child, TIF_PATCH_PENDING);
+
+	child->patch_state = current->patch_state;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/lockdep.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/lockdep.c
@@ -183,13 +183,11 @@
 static struct hlist_head lock_keys_hash[KEYHASH_SIZE];
 unsigned long nr_lock_classes;
 unsigned long nr_zapped_classes;
-#ifndef CONFIG_DEBUG_LOCKDEP
-static
-#endif
+unsigned long max_lock_class_idx;
 struct lock_class lock_classes[MAX_LOCKDEP_KEYS];
-static DECLARE_BITMAP(lock_classes_in_use, MAX_LOCKDEP_KEYS);
+DECLARE_BITMAP(lock_classes_in_use, MAX_LOCKDEP_KEYS);
 
-static inline struct lock_class *hlock_class(struct held_lock *hlock)
+inline struct lock_class *lockdep_hlock_class(struct held_lock *hlock)
 {
 	unsigned int class_idx = hlock->class_idx;
 
@@ -210,6 +208,8 @@
 	 */
 	return lock_classes + class_idx;
 }
+EXPORT_SYMBOL_GPL(lockdep_hlock_class);
+#define hlock_class(hlock) lockdep_hlock_class(hlock)
 
 #ifdef CONFIG_LOCK_STAT
 static DEFINE_PER_CPU(struct lock_class_stats[MAX_LOCKDEP_KEYS], cpu_lock_stats);
@@ -338,7 +338,7 @@
  * elements. These elements are linked together by the lock_entry member in
  * struct lock_class.
  */
-LIST_HEAD(all_lock_classes);
+static LIST_HEAD(all_lock_classes);
 static LIST_HEAD(free_lock_classes);
 
 /**
@@ -888,7 +888,7 @@
 	if (DEBUG_LOCKS_WARN_ON(!irqs_disabled()))
 		return NULL;
 
-	hlist_for_each_entry_rcu(class, hash_head, hash_entry) {
+	hlist_for_each_entry_rcu_notrace(class, hash_head, hash_entry) {
 		if (class->key == key) {
 			/*
 			 * Huh! same key, different name? Did someone trample
@@ -1240,6 +1240,7 @@
 	struct lockdep_subclass_key *key;
 	struct hlist_head *hash_head;
 	struct lock_class *class;
+	int idx;
 
 	DEBUG_LOCKS_WARN_ON(!irqs_disabled());
 
@@ -1305,6 +1306,9 @@
 	 * of classes.
 	 */
 	list_move_tail(&class->lock_entry, &all_lock_classes);
+	idx = class - lock_classes;
+	if (idx > max_lock_class_idx)
+		max_lock_class_idx = idx;
 
 	if (verbose(class)) {
 		graph_unlock();
@@ -1366,7 +1370,7 @@
  */
 static int add_lock_to_list(struct lock_class *this,
 			    struct lock_class *links_to, struct list_head *head,
-			    unsigned long ip, u16 distance, u8 dep,
+			    u16 distance, u8 dep,
 			    const struct lock_trace *trace)
 {
 	struct lock_list *entry;
@@ -3119,19 +3123,15 @@
 	 * to the previous lock's dependency list:
 	 */
 	ret = add_lock_to_list(hlock_class(next), hlock_class(prev),
-			       &hlock_class(prev)->locks_after,
-			       next->acquire_ip, distance,
-			       calc_dep(prev, next),
-			       *trace);
+			       &hlock_class(prev)->locks_after, distance,
+			       calc_dep(prev, next), *trace);
 
 	if (!ret)
 		return 0;
 
 	ret = add_lock_to_list(hlock_class(prev), hlock_class(next),
-			       &hlock_class(next)->locks_before,
-			       next->acquire_ip, distance,
-			       calc_depb(prev, next),
-			       *trace);
+			       &hlock_class(next)->locks_before, distance,
+			       calc_depb(prev, next), *trace);
 	if (!ret)
 		return 0;
 
@@ -3418,7 +3418,8 @@
 		size = chain_block_size(curr);
 		if (likely(size >= req)) {
 			del_chain_block(0, size, chain_block_next(curr));
-			add_chain_block(curr + req, size - req);
+			if (size > req)
+				add_chain_block(curr + req, size - req);
 			return curr;
 		}
 	}
@@ -3450,7 +3451,7 @@
 	u16 chain_hlock = chain_hlocks[chain->base + i];
 	unsigned int class_idx = chain_hlock_class_idx(chain_hlock);
 
-	return lock_classes + class_idx - 1;
+	return lock_classes + class_idx;
 }
 
 /*
@@ -3518,7 +3519,7 @@
 		hlock_id = chain_hlocks[chain->base + i];
 		chain_key = print_chain_key_iteration(hlock_id, chain_key);
 
-		print_lock_name(lock_classes + chain_hlock_class_idx(hlock_id) - 1);
+		print_lock_name(lock_classes + chain_hlock_class_idx(hlock_id));
 		printk("\n");
 	}
 }
@@ -4222,14 +4223,13 @@
 
 /**
  * lockdep_hardirqs_on_prepare - Prepare for enabling interrupts
- * @ip:		Caller address
  *
  * Invoked before a possible transition to RCU idle from exit to user or
  * guest mode. This ensures that all RCU operations are done before RCU
  * stops watching. After the RCU transition lockdep_hardirqs_on() has to be
  * invoked to set the final state.
  */
-void lockdep_hardirqs_on_prepare(unsigned long ip)
+void lockdep_hardirqs_on_prepare(void)
 {
 	if (unlikely(!debug_locks))
 		return;
@@ -4826,8 +4826,7 @@
 
 static void
 print_lock_nested_lock_not_held(struct task_struct *curr,
-				struct held_lock *hlock,
-				unsigned long ip)
+				struct held_lock *hlock)
 {
 	if (!debug_locks_off())
 		return;
@@ -5003,7 +5002,7 @@
 	chain_key = iterate_chain_key(chain_key, hlock_id(hlock));
 
 	if (nest_lock && !__lock_is_held(nest_lock, -1)) {
-		print_lock_nested_lock_not_held(curr, hlock, ip);
+		print_lock_nested_lock_not_held(curr, hlock);
 		return 0;
 	}
 
@@ -5200,9 +5199,10 @@
 		return 0;
 	}
 
-	lockdep_init_map_waits(lock, name, key, 0,
-			       lock->wait_type_inner,
-			       lock->wait_type_outer);
+	lockdep_init_map_type(lock, name, key, 0,
+			      lock->wait_type_inner,
+			      lock->wait_type_outer,
+			      lock->lock_type);
 	class = register_lock_class(lock, subclass, 0);
 	hlock->class_idx = class - lock_classes;
 
@@ -5366,7 +5366,7 @@
 		struct held_lock *hlock = curr->held_locks + i;
 
 		if (match_held_lock(hlock, lock)) {
-			if (read == -1 || hlock->read == read)
+			if (read == -1 || !!hlock->read == read)
 				return LOCK_STATE_HELD;
 
 			return LOCK_STATE_NOT_HELD;
@@ -5986,6 +5986,8 @@
 		WRITE_ONCE(class->name, NULL);
 		nr_lock_classes--;
 		__clear_bit(class - lock_classes, lock_classes_in_use);
+		if (class - lock_classes == max_lock_class_idx)
+			max_lock_class_idx--;
 	} else {
 		WARN_ONCE(true, "%s() failed for class %s\n", __func__,
 			  class->name);
@@ -6028,25 +6030,27 @@
 static void free_zapped_rcu(struct rcu_head *cb);
 
 /*
- * Schedule an RCU callback if no RCU callback is pending. Must be called with
- * the graph lock held.
- */
-static void call_rcu_zapped(struct pending_free *pf)
+* See if we need to queue an RCU callback, must called with
+* the lockdep lock held, returns false if either we don't have
+* any pending free or the callback is already scheduled.
+* Otherwise, a call_rcu() must follow this function call.
+*/
+static bool prepare_call_rcu_zapped(struct pending_free *pf)
 {
 	WARN_ON_ONCE(inside_selftest());
 
 	if (list_empty(&pf->zapped))
-		return;
+		return false;
 
 	if (delayed_free.scheduled)
-		return;
+		return false;
 
 	delayed_free.scheduled = true;
 
 	WARN_ON_ONCE(delayed_free.pf + delayed_free.index != pf);
 	delayed_free.index ^= 1;
 
-	call_rcu(&delayed_free.rcu_head, free_zapped_rcu);
+	return true;
 }
 
 /* The caller must hold the graph lock. May be called from RCU context. */
@@ -6072,6 +6076,7 @@
 {
 	struct pending_free *pf;
 	unsigned long flags;
+	bool need_callback;
 
 	if (WARN_ON_ONCE(ch != &delayed_free.rcu_head))
 		return;
@@ -6083,14 +6088,18 @@
 	pf = delayed_free.pf + (delayed_free.index ^ 1);
 	__free_zapped_classes(pf);
 	delayed_free.scheduled = false;
+	need_callback =
+		prepare_call_rcu_zapped(delayed_free.pf + delayed_free.index);
+	lockdep_unlock();
+	raw_local_irq_restore(flags);
 
 	/*
-	 * If there's anything on the open list, close and start a new callback.
-	 */
-	call_rcu_zapped(delayed_free.pf + delayed_free.index);
+	* If there's pending free and its callback has not been scheduled,
+	* queue an RCU callback.
+	*/
+	if (need_callback)
+		call_rcu(&delayed_free.rcu_head, free_zapped_rcu);
 
-	lockdep_unlock();
-	raw_local_irq_restore(flags);
 }
 
 /*
@@ -6130,6 +6139,7 @@
 {
 	struct pending_free *pf;
 	unsigned long flags;
+	bool need_callback;
 
 	init_data_structures_once();
 
@@ -6137,10 +6147,11 @@
 	lockdep_lock();
 	pf = get_pending_free();
 	__lockdep_free_key_range(pf, start, size);
-	call_rcu_zapped(pf);
+	need_callback = prepare_call_rcu_zapped(pf);
 	lockdep_unlock();
 	raw_local_irq_restore(flags);
-
+	if (need_callback)
+		call_rcu(&delayed_free.rcu_head, free_zapped_rcu);
 	/*
 	 * Wait for any possible iterators from look_up_lock_class() to pass
 	 * before continuing to free the memory they refer to.
@@ -6234,6 +6245,7 @@
 	struct pending_free *pf;
 	unsigned long flags;
 	int locked;
+	bool need_callback = false;
 
 	raw_local_irq_save(flags);
 	locked = graph_lock();
@@ -6242,11 +6254,13 @@
 
 	pf = get_pending_free();
 	__lockdep_reset_lock(pf, lock);
-	call_rcu_zapped(pf);
+	need_callback = prepare_call_rcu_zapped(pf);
 
 	graph_unlock();
 out_irq:
 	raw_local_irq_restore(flags);
+	if (need_callback)
+		call_rcu(&delayed_free.rcu_head, free_zapped_rcu);
 }
 
 /*
@@ -6276,7 +6290,13 @@
 		lockdep_reset_lock_reg(lock);
 }
 
-/* Unregister a dynamically allocated key. */
+/*
+ * Unregister a dynamically allocated key.
+ *
+ * Unlike lockdep_register_key(), a search is always done to find a matching
+ * key irrespective of debug_locks to avoid potential invalid access to freed
+ * memory in lock_class entry.
+ */
 void lockdep_unregister_key(struct lock_class_key *key)
 {
 	struct hlist_head *hash_head = keyhashentry(key);
@@ -6284,6 +6304,7 @@
 	struct pending_free *pf;
 	unsigned long flags;
 	bool found = false;
+	bool need_callback = false;
 
 	might_sleep();
 
@@ -6291,10 +6312,8 @@
 		return;
 
 	raw_local_irq_save(flags);
-	if (!graph_lock())
-		goto out_irq;
+	lockdep_lock();
 
-	pf = get_pending_free();
 	hlist_for_each_entry_rcu(k, hash_head, hash_entry) {
 		if (k == key) {
 			hlist_del_rcu(&k->hash_entry);
@@ -6302,13 +6321,18 @@
 			break;
 		}
 	}
-	WARN_ON_ONCE(!found);
-	__lockdep_free_key_range(pf, key, 1);
-	call_rcu_zapped(pf);
-	graph_unlock();
-out_irq:
+	WARN_ON_ONCE(!found && debug_locks);
+	if (found) {
+		pf = get_pending_free();
+		__lockdep_free_key_range(pf, key, 1);
+		need_callback = prepare_call_rcu_zapped(pf);
+	}
+	lockdep_unlock();
 	raw_local_irq_restore(flags);
 
+	if (need_callback)
+		call_rcu(&delayed_free.rcu_head, free_zapped_rcu);
+
 	/* Wait until is_dynamic_key() has finished accessing k->hash_entry. */
 	synchronize_rcu();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/lockdep_internals.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/lockdep_internals.h
@@ -121,7 +121,6 @@
 
 #define MAX_LOCKDEP_CHAIN_HLOCKS (MAX_LOCKDEP_CHAINS*5)
 
-extern struct list_head all_lock_classes;
 extern struct lock_chain lock_chains[];
 
 #define LOCK_USAGE_CHARS (2*XXX_LOCK_USAGE_STATES + 1)
@@ -151,6 +150,10 @@
 
 extern unsigned int max_lockdep_depth;
 extern unsigned int max_bfs_queue_depth;
+extern unsigned long max_lock_class_idx;
+
+extern struct lock_class lock_classes[MAX_LOCKDEP_KEYS];
+extern unsigned long lock_classes_in_use[];
 
 #ifdef CONFIG_PROVE_LOCKING
 extern unsigned long lockdep_count_forward_deps(struct lock_class *);
@@ -205,7 +208,6 @@
 };
 
 DECLARE_PER_CPU(struct lockdep_stats, lockdep_stats);
-extern struct lock_class lock_classes[MAX_LOCKDEP_KEYS];
 
 #define __debug_atomic_inc(ptr)					\
 	this_cpu_inc(lockdep_stats.ptr);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/lockdep_proc.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/lockdep_proc.c
@@ -24,14 +24,33 @@
 
 #include "lockdep_internals.h"
 
+/*
+ * Since iteration of lock_classes is done without holding the lockdep lock,
+ * it is not safe to iterate all_lock_classes list directly as the iteration
+ * may branch off to free_lock_classes or the zapped list. Iteration is done
+ * directly on the lock_classes array by checking the lock_classes_in_use
+ * bitmap and max_lock_class_idx.
+ */
+#define iterate_lock_classes(idx, class)				\
+	for (idx = 0, class = lock_classes; idx <= max_lock_class_idx;	\
+	     idx++, class++)
+
 static void *l_next(struct seq_file *m, void *v, loff_t *pos)
 {
-	return seq_list_next(v, &all_lock_classes, pos);
+	struct lock_class *class = v;
+
+	++class;
+	*pos = class - lock_classes;
+	return (*pos > max_lock_class_idx) ? NULL : class;
 }
 
 static void *l_start(struct seq_file *m, loff_t *pos)
 {
-	return seq_list_start_head(&all_lock_classes, *pos);
+	unsigned long idx = *pos;
+
+	if (idx > max_lock_class_idx)
+		return NULL;
+	return lock_classes + idx;
 }
 
 static void l_stop(struct seq_file *m, void *v)
@@ -57,14 +76,16 @@
 
 static int l_show(struct seq_file *m, void *v)
 {
-	struct lock_class *class = list_entry(v, struct lock_class, lock_entry);
+	struct lock_class *class = v;
 	struct lock_list *entry;
 	char usage[LOCK_USAGE_CHARS];
+	int idx = class - lock_classes;
 
-	if (v == &all_lock_classes) {
+	if (v == lock_classes)
 		seq_printf(m, "all lock classes:\n");
+
+	if (!test_bit(idx, lock_classes_in_use))
 		return 0;
-	}
 
 	seq_printf(m, "%p", class->key);
 #ifdef CONFIG_DEBUG_LOCKDEP
@@ -220,8 +241,11 @@
 
 #ifdef CONFIG_PROVE_LOCKING
 	struct lock_class *class;
+	unsigned long idx;
 
-	list_for_each_entry(class, &all_lock_classes, lock_entry) {
+	iterate_lock_classes(idx, class) {
+		if (!test_bit(idx, lock_classes_in_use))
+			continue;
 
 		if (class->usage_mask == 0)
 			nr_unused++;
@@ -254,6 +278,7 @@
 
 		sum_forward_deps += lockdep_count_forward_deps(class);
 	}
+
 #ifdef CONFIG_DEBUG_LOCKDEP
 	DEBUG_LOCKS_WARN_ON(debug_atomic_read(nr_unused_locks) != nr_unused);
 #endif
@@ -345,6 +370,8 @@
 	seq_printf(m, " max bfs queue depth:           %11u\n",
 			max_bfs_queue_depth);
 #endif
+	seq_printf(m, " max lock class index:          %11lu\n",
+			max_lock_class_idx);
 	lockdep_stats_debug_show(m);
 	seq_printf(m, " debug_locks:                   %11u\n",
 			debug_locks);
@@ -622,12 +649,16 @@
 	if (!res) {
 		struct lock_stat_data *iter = data->stats;
 		struct seq_file *m = file->private_data;
+		unsigned long idx;
 
-		list_for_each_entry(class, &all_lock_classes, lock_entry) {
+		iterate_lock_classes(idx, class) {
+			if (!test_bit(idx, lock_classes_in_use))
+				continue;
 			iter->class = class;
 			iter->stats = lock_stats(class);
 			iter++;
 		}
+
 		data->iter_end = iter;
 
 		sort(data->stats, data->iter_end - data->stats,
@@ -645,6 +676,7 @@
 			       size_t count, loff_t *ppos)
 {
 	struct lock_class *class;
+	unsigned long idx;
 	char c;
 
 	if (count) {
@@ -654,8 +686,11 @@
 		if (c != '0')
 			return count;
 
-		list_for_each_entry(class, &all_lock_classes, lock_entry)
+		iterate_lock_classes(idx, class) {
+			if (!test_bit(idx, lock_classes_in_use))
+				continue;
 			clear_lock_stats(class);
+		}
 	}
 	return count;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/mutex-debug.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/mutex-debug.c
@@ -12,6 +12,7 @@
  */
 #include <linux/mutex.h>
 #include <linux/delay.h>
+#include <linux/device.h>
 #include <linux/export.h>
 #include <linux/poison.h>
 #include <linux/sched.h>
@@ -89,6 +90,17 @@
 	lock->magic = lock;
 }
 
+static void devm_mutex_release(void *res)
+{
+	mutex_destroy(res);
+}
+
+int __devm_mutex_init(struct device *dev, struct mutex *lock)
+{
+	return devm_add_action_or_reset(dev, devm_mutex_release, lock);
+}
+EXPORT_SYMBOL_GPL(__devm_mutex_init);
+
 /***
  * mutex_destroy - mark a mutex unusable
  * @lock: the mutex to be destroyed
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/rtmutex.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/rtmutex.c
@@ -87,15 +87,31 @@
  * set this bit before looking at the lock.
  */
 
-static __always_inline void
-rt_mutex_set_owner(struct rt_mutex_base *lock, struct task_struct *owner)
+static __always_inline struct task_struct *
+rt_mutex_owner_encode(struct rt_mutex_base *lock, struct task_struct *owner)
 {
 	unsigned long val = (unsigned long)owner;
 
 	if (rt_mutex_has_waiters(lock))
 		val |= RT_MUTEX_HAS_WAITERS;
 
-	WRITE_ONCE(lock->owner, (struct task_struct *)val);
+	return (struct task_struct *)val;
+}
+
+static __always_inline void
+rt_mutex_set_owner(struct rt_mutex_base *lock, struct task_struct *owner)
+{
+	/*
+	 * lock->wait_lock is held but explicit acquire semantics are needed
+	 * for a new lock owner so WRITE_ONCE is insufficient.
+	 */
+	xchg_acquire(&lock->owner, rt_mutex_owner_encode(lock, owner));
+}
+
+static __always_inline void rt_mutex_clear_owner(struct rt_mutex_base *lock)
+{
+	/* lock->wait_lock is held so the unlock provides release semantics. */
+	WRITE_ONCE(lock->owner, rt_mutex_owner_encode(lock, NULL));
 }
 
 static __always_inline void clear_rt_mutex_waiters(struct rt_mutex_base *lock)
@@ -104,7 +120,8 @@
 			((unsigned long)lock->owner & ~RT_MUTEX_HAS_WAITERS);
 }
 
-static __always_inline void fixup_rt_mutex_waiters(struct rt_mutex_base *lock)
+static __always_inline void
+fixup_rt_mutex_waiters(struct rt_mutex_base *lock, bool acquire_lock)
 {
 	unsigned long owner, *p = (unsigned long *) &lock->owner;
 
@@ -170,8 +187,21 @@
 	 * still set.
 	 */
 	owner = READ_ONCE(*p);
-	if (owner & RT_MUTEX_HAS_WAITERS)
-		WRITE_ONCE(*p, owner & ~RT_MUTEX_HAS_WAITERS);
+	if (owner & RT_MUTEX_HAS_WAITERS) {
+		/*
+		 * See rt_mutex_set_owner() and rt_mutex_clear_owner() on
+		 * why xchg_acquire() is used for updating owner for
+		 * locking and WRITE_ONCE() for unlocking.
+		 *
+		 * WRITE_ONCE() would work for the acquire case too, but
+		 * in case that the lock acquisition failed it might
+		 * force other lockers into the slow path unnecessarily.
+		 */
+		if (acquire_lock)
+			xchg_acquire(p, owner & ~RT_MUTEX_HAS_WAITERS);
+		else
+			WRITE_ONCE(*p, owner & ~RT_MUTEX_HAS_WAITERS);
+	}
 }
 
 /*
@@ -206,6 +236,13 @@
 		owner = *p;
 	} while (cmpxchg_relaxed(p, owner,
 				 owner | RT_MUTEX_HAS_WAITERS) != owner);
+
+	/*
+	 * The cmpxchg loop above is relaxed to avoid back-to-back ACQUIRE
+	 * operations in the event of contention. Ensure the successful
+	 * cmpxchg is visible.
+	 */
+	smp_mb__after_atomic();
 }
 
 /*
@@ -294,21 +331,43 @@
 	return prio;
 }
 
+/*
+ * Update the waiter->tree copy of the sort keys.
+ */
 static __always_inline void
 waiter_update_prio(struct rt_mutex_waiter *waiter, struct task_struct *task)
 {
-	waiter->prio = __waiter_prio(task);
-	waiter->deadline = task->dl.deadline;
+	lockdep_assert_held(&waiter->lock->wait_lock);
+	lockdep_assert(RB_EMPTY_NODE(&waiter->tree.entry));
+
+	waiter->tree.prio = __waiter_prio(task);
+	waiter->tree.deadline = task->dl.deadline;
 }
 
 /*
- * Only use with rt_mutex_waiter_{less,equal}()
+ * Update the waiter->pi_tree copy of the sort keys (from the tree copy).
  */
+static __always_inline void
+waiter_clone_prio(struct rt_mutex_waiter *waiter, struct task_struct *task)
+{
+	lockdep_assert_held(&waiter->lock->wait_lock);
+	lockdep_assert_held(&task->pi_lock);
+	lockdep_assert(RB_EMPTY_NODE(&waiter->pi_tree.entry));
+
+	waiter->pi_tree.prio = waiter->tree.prio;
+	waiter->pi_tree.deadline = waiter->tree.deadline;
+}
+
+/*
+ * Only use with rt_waiter_node_{less,equal}()
+ */
+#define task_to_waiter_node(p)	\
+	&(struct rt_waiter_node){ .prio = __waiter_prio(p), .deadline = (p)->dl.deadline }
 #define task_to_waiter(p)	\
-	&(struct rt_mutex_waiter){ .prio = __waiter_prio(p), .deadline = (p)->dl.deadline }
+	&(struct rt_mutex_waiter){ .tree = *task_to_waiter_node(p) }
 
-static __always_inline int rt_mutex_waiter_less(struct rt_mutex_waiter *left,
-						struct rt_mutex_waiter *right)
+static __always_inline int rt_waiter_node_less(struct rt_waiter_node *left,
+					       struct rt_waiter_node *right)
 {
 	if (left->prio < right->prio)
 		return 1;
@@ -325,8 +384,8 @@
 	return 0;
 }
 
-static __always_inline int rt_mutex_waiter_equal(struct rt_mutex_waiter *left,
-						 struct rt_mutex_waiter *right)
+static __always_inline int rt_waiter_node_equal(struct rt_waiter_node *left,
+						 struct rt_waiter_node *right)
 {
 	if (left->prio != right->prio)
 		return 0;
@@ -346,7 +405,7 @@
 static inline bool rt_mutex_steal(struct rt_mutex_waiter *waiter,
 				  struct rt_mutex_waiter *top_waiter)
 {
-	if (rt_mutex_waiter_less(waiter, top_waiter))
+	if (rt_waiter_node_less(&waiter->tree, &top_waiter->tree))
 		return true;
 
 #ifdef RT_MUTEX_BUILD_SPINLOCKS
@@ -354,30 +413,30 @@
 	 * Note that RT tasks are excluded from same priority (lateral)
 	 * steals to prevent the introduction of an unbounded latency.
 	 */
-	if (rt_prio(waiter->prio) || dl_prio(waiter->prio))
+	if (rt_prio(waiter->tree.prio) || dl_prio(waiter->tree.prio))
 		return false;
 
-	return rt_mutex_waiter_equal(waiter, top_waiter);
+	return rt_waiter_node_equal(&waiter->tree, &top_waiter->tree);
 #else
 	return false;
 #endif
 }
 
 #define __node_2_waiter(node) \
-	rb_entry((node), struct rt_mutex_waiter, tree_entry)
+	rb_entry((node), struct rt_mutex_waiter, tree.entry)
 
 static __always_inline bool __waiter_less(struct rb_node *a, const struct rb_node *b)
 {
 	struct rt_mutex_waiter *aw = __node_2_waiter(a);
 	struct rt_mutex_waiter *bw = __node_2_waiter(b);
 
-	if (rt_mutex_waiter_less(aw, bw))
+	if (rt_waiter_node_less(&aw->tree, &bw->tree))
 		return 1;
 
 	if (!build_ww_mutex())
 		return 0;
 
-	if (rt_mutex_waiter_less(bw, aw))
+	if (rt_waiter_node_less(&bw->tree, &aw->tree))
 		return 0;
 
 	/* NOTE: relies on waiter->ww_ctx being set before insertion */
@@ -395,48 +454,58 @@
 static __always_inline void
 rt_mutex_enqueue(struct rt_mutex_base *lock, struct rt_mutex_waiter *waiter)
 {
-	rb_add_cached(&waiter->tree_entry, &lock->waiters, __waiter_less);
+	lockdep_assert_held(&lock->wait_lock);
+
+	rb_add_cached(&waiter->tree.entry, &lock->waiters, __waiter_less);
 }
 
 static __always_inline void
 rt_mutex_dequeue(struct rt_mutex_base *lock, struct rt_mutex_waiter *waiter)
 {
-	if (RB_EMPTY_NODE(&waiter->tree_entry))
+	lockdep_assert_held(&lock->wait_lock);
+
+	if (RB_EMPTY_NODE(&waiter->tree.entry))
 		return;
 
-	rb_erase_cached(&waiter->tree_entry, &lock->waiters);
-	RB_CLEAR_NODE(&waiter->tree_entry);
+	rb_erase_cached(&waiter->tree.entry, &lock->waiters);
+	RB_CLEAR_NODE(&waiter->tree.entry);
 }
 
-#define __node_2_pi_waiter(node) \
-	rb_entry((node), struct rt_mutex_waiter, pi_tree_entry)
+#define __node_2_rt_node(node) \
+	rb_entry((node), struct rt_waiter_node, entry)
 
-static __always_inline bool
-__pi_waiter_less(struct rb_node *a, const struct rb_node *b)
+static __always_inline bool __pi_waiter_less(struct rb_node *a, const struct rb_node *b)
 {
-	return rt_mutex_waiter_less(__node_2_pi_waiter(a), __node_2_pi_waiter(b));
+	return rt_waiter_node_less(__node_2_rt_node(a), __node_2_rt_node(b));
 }
 
 static __always_inline void
 rt_mutex_enqueue_pi(struct task_struct *task, struct rt_mutex_waiter *waiter)
 {
-	rb_add_cached(&waiter->pi_tree_entry, &task->pi_waiters, __pi_waiter_less);
+	lockdep_assert_held(&task->pi_lock);
+
+	rb_add_cached(&waiter->pi_tree.entry, &task->pi_waiters, __pi_waiter_less);
 }
 
 static __always_inline void
 rt_mutex_dequeue_pi(struct task_struct *task, struct rt_mutex_waiter *waiter)
 {
-	if (RB_EMPTY_NODE(&waiter->pi_tree_entry))
+	lockdep_assert_held(&task->pi_lock);
+
+	if (RB_EMPTY_NODE(&waiter->pi_tree.entry))
 		return;
 
-	rb_erase_cached(&waiter->pi_tree_entry, &task->pi_waiters);
-	RB_CLEAR_NODE(&waiter->pi_tree_entry);
+	rb_erase_cached(&waiter->pi_tree.entry, &task->pi_waiters);
+	RB_CLEAR_NODE(&waiter->pi_tree.entry);
 }
 
-static __always_inline void rt_mutex_adjust_prio(struct task_struct *p)
+static __always_inline void rt_mutex_adjust_prio(struct rt_mutex_base *lock,
+						 struct task_struct *p)
 {
 	struct task_struct *pi_task = NULL;
 
+	lockdep_assert_held(&lock->wait_lock);
+	lockdep_assert(rt_mutex_owner(lock) == p);
 	lockdep_assert_held(&p->pi_lock);
 
 	if (task_has_pi_waiters(p))
@@ -525,9 +594,14 @@
  * Chain walk basics and protection scope
  *
  * [R] refcount on task
- * [P] task->pi_lock held
+ * [Pn] task->pi_lock held
  * [L] rtmutex->wait_lock held
  *
+ * Normal locking order:
+ *
+ *   rtmutex->wait_lock
+ *     task->pi_lock
+ *
  * Step	Description				Protected by
  *	function arguments:
  *	@task					[R]
@@ -542,27 +616,32 @@
  *	again:
  *	  loop_sanity_check();
  *	retry:
- * [1]	  lock(task->pi_lock);			[R] acquire [P]
- * [2]	  waiter = task->pi_blocked_on;		[P]
- * [3]	  check_exit_conditions_1();		[P]
- * [4]	  lock = waiter->lock;			[P]
- * [5]	  if (!try_lock(lock->wait_lock)) {	[P] try to acquire [L]
- *	    unlock(task->pi_lock);		release [P]
+ * [1]	  lock(task->pi_lock);			[R] acquire [P1]
+ * [2]	  waiter = task->pi_blocked_on;		[P1]
+ * [3]	  check_exit_conditions_1();		[P1]
+ * [4]	  lock = waiter->lock;			[P1]
+ * [5]	  if (!try_lock(lock->wait_lock)) {	[P1] try to acquire [L]
+ *	    unlock(task->pi_lock);		release [P1]
  *	    goto retry;
  *	  }
- * [6]	  check_exit_conditions_2();		[P] + [L]
- * [7]	  requeue_lock_waiter(lock, waiter);	[P] + [L]
- * [8]	  unlock(task->pi_lock);		release [P]
+ * [6]	  check_exit_conditions_2();		[P1] + [L]
+ * [7]	  requeue_lock_waiter(lock, waiter);	[P1] + [L]
+ * [8]	  unlock(task->pi_lock);		release [P1]
  *	  put_task_struct(task);		release [R]
  * [9]	  check_exit_conditions_3();		[L]
  * [10]	  task = owner(lock);			[L]
  *	  get_task_struct(task);		[L] acquire [R]
- *	  lock(task->pi_lock);			[L] acquire [P]
- * [11]	  requeue_pi_waiter(tsk, waiters(lock));[P] + [L]
- * [12]	  check_exit_conditions_4();		[P] + [L]
- * [13]	  unlock(task->pi_lock);		release [P]
+ *	  lock(task->pi_lock);			[L] acquire [P2]
+ * [11]	  requeue_pi_waiter(tsk, waiters(lock));[P2] + [L]
+ * [12]	  check_exit_conditions_4();		[P2] + [L]
+ * [13]	  unlock(task->pi_lock);		release [P2]
  *	  unlock(lock->wait_lock);		release [L]
  *	  goto again;
+ *
+ * Where P1 is the blocking task and P2 is the lock owner; going up one step
+ * the owner becomes the next blocked task etc..
+ *
+*
  */
 static int __sched rt_mutex_adjust_prio_chain(struct task_struct *task,
 					      enum rtmutex_chainwalk chwalk,
@@ -710,7 +789,7 @@
 	 * enabled we continue, but stop the requeueing in the chain
 	 * walk.
 	 */
-	if (rt_mutex_waiter_equal(waiter, task_to_waiter(task))) {
+	if (rt_waiter_node_equal(&waiter->tree, task_to_waiter_node(task))) {
 		if (!detect_deadlock)
 			goto out_unlock_pi;
 		else
@@ -718,13 +797,18 @@
 	}
 
 	/*
-	 * [4] Get the next lock
+	 * [4] Get the next lock; per holding task->pi_lock we can't unblock
+	 * and guarantee @lock's existence.
 	 */
 	lock = waiter->lock;
 	/*
 	 * [5] We need to trylock here as we are holding task->pi_lock,
 	 * which is the reverse lock order versus the other rtmutex
 	 * operations.
+	 *
+	 * Per the above, holding task->pi_lock guarantees lock exists, so
+	 * inverting this lock order is infeasible from a life-time
+	 * perspective.
 	 */
 	if (!raw_spin_trylock(&lock->wait_lock)) {
 		raw_spin_unlock_irq(&task->pi_lock);
@@ -828,17 +912,18 @@
 	 * or
 	 *
 	 *   DL CBS enforcement advancing the effective deadline.
-	 *
-	 * Even though pi_waiters also uses these fields, and that tree is only
-	 * updated in [11], we can do this here, since we hold [L], which
-	 * serializes all pi_waiters access and rb_erase() does not care about
-	 * the values of the node being removed.
 	 */
 	waiter_update_prio(waiter, task);
 
 	rt_mutex_enqueue(lock, waiter);
 
-	/* [8] Release the task */
+	/*
+	 * [8] Release the (blocking) task in preparation for
+	 * taking the owner task in [10].
+	 *
+	 * Since we hold lock->waiter_lock, task cannot unblock, even if we
+	 * release task->pi_lock.
+	 */
 	raw_spin_unlock(&task->pi_lock);
 	put_task_struct(task);
 
@@ -855,13 +940,19 @@
 		 * then we need to wake the new top waiter up to try
 		 * to get the lock.
 		 */
-		if (prerequeue_top_waiter != rt_mutex_top_waiter(lock))
-			wake_up_state(waiter->task, waiter->wake_state);
+		top_waiter = rt_mutex_top_waiter(lock);
+		if (prerequeue_top_waiter != top_waiter)
+			wake_up_state(top_waiter->task, top_waiter->wake_state);
 		raw_spin_unlock_irq(&lock->wait_lock);
 		return 0;
 	}
 
-	/* [10] Grab the next task, i.e. the owner of @lock */
+	/*
+	 * [10] Grab the next task, i.e. the owner of @lock
+	 *
+	 * Per holding lock->wait_lock and checking for !owner above, there
+	 * must be an owner and it cannot go away.
+	 */
 	task = get_task_struct(rt_mutex_owner(lock));
 	raw_spin_lock(&task->pi_lock);
 
@@ -874,8 +965,9 @@
 		 * and adjust the priority of the owner.
 		 */
 		rt_mutex_dequeue_pi(task, prerequeue_top_waiter);
+		waiter_clone_prio(waiter, task);
 		rt_mutex_enqueue_pi(task, waiter);
-		rt_mutex_adjust_prio(task);
+		rt_mutex_adjust_prio(lock, task);
 
 	} else if (prerequeue_top_waiter == waiter) {
 		/*
@@ -890,8 +982,9 @@
 		 */
 		rt_mutex_dequeue_pi(task, waiter);
 		waiter = rt_mutex_top_waiter(lock);
+		waiter_clone_prio(waiter, task);
 		rt_mutex_enqueue_pi(task, waiter);
-		rt_mutex_adjust_prio(task);
+		rt_mutex_adjust_prio(lock, task);
 	} else {
 		/*
 		 * Nothing changed. No need to do any priority
@@ -1104,6 +1197,7 @@
 	waiter->task = task;
 	waiter->lock = lock;
 	waiter_update_prio(waiter, task);
+	waiter_clone_prio(waiter, task);
 
 	/* Get the top priority waiter on the lock */
 	if (rt_mutex_has_waiters(lock))
@@ -1137,7 +1231,7 @@
 		rt_mutex_dequeue_pi(owner, top_waiter);
 		rt_mutex_enqueue_pi(owner, waiter);
 
-		rt_mutex_adjust_prio(owner);
+		rt_mutex_adjust_prio(lock, owner);
 		if (owner->pi_blocked_on)
 			chain_walk = 1;
 	} else if (rt_mutex_cond_detect_deadlock(waiter, chwalk)) {
@@ -1184,6 +1278,8 @@
 {
 	struct rt_mutex_waiter *waiter;
 
+	lockdep_assert_held(&lock->wait_lock);
+
 	raw_spin_lock(&current->pi_lock);
 
 	waiter = rt_mutex_top_waiter(lock);
@@ -1196,7 +1292,7 @@
 	 * task unblocks.
 	 */
 	rt_mutex_dequeue_pi(current, waiter);
-	rt_mutex_adjust_prio(current);
+	rt_mutex_adjust_prio(lock, current);
 
 	/*
 	 * As we are waking up the top waiter, and the waiter stays
@@ -1231,7 +1327,7 @@
 	 * try_to_take_rt_mutex() sets the lock waiters bit
 	 * unconditionally. Clean this up.
 	 */
-	fixup_rt_mutex_waiters(lock);
+	fixup_rt_mutex_waiters(lock, true);
 
 	return ret;
 }
@@ -1373,7 +1469,7 @@
 		 *  - the VCPU on which owner runs is preempted
 		 */
 		if (!owner->on_cpu || need_resched() ||
-		    rt_mutex_waiter_is_top_waiter(lock, waiter) ||
+		    !rt_mutex_waiter_is_top_waiter(lock, waiter) ||
 		    vcpu_is_preempted(task_cpu(owner))) {
 			res = false;
 			break;
@@ -1433,7 +1529,7 @@
 	if (rt_mutex_has_waiters(lock))
 		rt_mutex_enqueue_pi(owner, rt_mutex_top_waiter(lock));
 
-	rt_mutex_adjust_prio(owner);
+	rt_mutex_adjust_prio(lock, owner);
 
 	/* Store the lock on which owner is blocked or NULL */
 	next_lock = task_blocked_on_lock(owner);
@@ -1517,6 +1613,7 @@
 }
 
 static void __sched rt_mutex_handle_deadlock(int res, int detect_deadlock,
+					     struct rt_mutex_base *lock,
 					     struct rt_mutex_waiter *w)
 {
 	/*
@@ -1529,10 +1626,10 @@
 	if (build_ww_mutex() && w->ww_ctx)
 		return;
 
-	/*
-	 * Yell loudly and stop the task right here.
-	 */
+	raw_spin_unlock_irq(&lock->wait_lock);
+
 	WARN(1, "rtmutex deadlock detected\n");
+
 	while (1) {
 		set_current_state(TASK_INTERRUPTIBLE);
 		schedule();
@@ -1584,14 +1681,14 @@
 	} else {
 		__set_current_state(TASK_RUNNING);
 		remove_waiter(lock, waiter);
-		rt_mutex_handle_deadlock(ret, chwalk, waiter);
+		rt_mutex_handle_deadlock(ret, chwalk, lock, waiter);
 	}
 
 	/*
 	 * try_to_take_rt_mutex() sets the waiter bit
 	 * unconditionally. We might have to fix that up.
 	 */
-	fixup_rt_mutex_waiters(lock);
+	fixup_rt_mutex_waiters(lock, true);
 	return ret;
 }
 
@@ -1701,7 +1798,7 @@
 	 * try_to_take_rt_mutex() sets the waiter bit unconditionally.
 	 * We might have to fix that up:
 	 */
-	fixup_rt_mutex_waiters(lock);
+	fixup_rt_mutex_waiters(lock, true);
 	debug_rt_mutex_free_waiter(&waiter);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/rtmutex_api.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/rtmutex_api.c
@@ -245,7 +245,7 @@
 void __sched rt_mutex_proxy_unlock(struct rt_mutex_base *lock)
 {
 	debug_rt_mutex_proxy_unlock(lock);
-	rt_mutex_set_owner(lock, NULL);
+	rt_mutex_clear_owner(lock);
 }
 
 /**
@@ -360,7 +360,7 @@
 	 * try_to_take_rt_mutex() sets the waiter bit unconditionally. We might
 	 * have to fix that up.
 	 */
-	fixup_rt_mutex_waiters(lock);
+	fixup_rt_mutex_waiters(lock, true);
 	raw_spin_unlock_irq(&lock->wait_lock);
 
 	return ret;
@@ -416,7 +416,7 @@
 	 * try_to_take_rt_mutex() sets the waiter bit unconditionally. We might
 	 * have to fix that up.
 	 */
-	fixup_rt_mutex_waiters(lock);
+	fixup_rt_mutex_waiters(lock, false);
 
 	raw_spin_unlock_irq(&lock->wait_lock);
 
@@ -437,7 +437,7 @@
 	raw_spin_lock_irqsave(&task->pi_lock, flags);
 
 	waiter = task->pi_blocked_on;
-	if (!waiter || rt_mutex_waiter_equal(waiter, task_to_waiter(task))) {
+	if (!waiter || rt_waiter_node_equal(&waiter->tree, task_to_waiter_node(task))) {
 		raw_spin_unlock_irqrestore(&task->pi_lock, flags);
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/rtmutex_common.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/rtmutex_common.h
@@ -17,27 +17,44 @@
 #include <linux/rtmutex.h>
 #include <linux/sched/wake_q.h>
 
+
+/*
+ * This is a helper for the struct rt_mutex_waiter below. A waiter goes in two
+ * separate trees and they need their own copy of the sort keys because of
+ * different locking requirements.
+ *
+ * @entry:		rbtree node to enqueue into the waiters tree
+ * @prio:		Priority of the waiter
+ * @deadline:		Deadline of the waiter if applicable
+ *
+ * See rt_waiter_node_less() and waiter_*_prio().
+ */
+struct rt_waiter_node {
+	struct rb_node	entry;
+	int		prio;
+	u64		deadline;
+};
+
 /*
  * This is the control structure for tasks blocked on a rt_mutex,
  * which is allocated on the kernel stack on of the blocked task.
  *
- * @tree_entry:		pi node to enqueue into the mutex waiters tree
- * @pi_tree_entry:	pi node to enqueue into the mutex owner waiters tree
+ * @tree:		node to enqueue into the mutex waiters tree
+ * @pi_tree:		node to enqueue into the mutex owner waiters tree
  * @task:		task reference to the blocked task
  * @lock:		Pointer to the rt_mutex on which the waiter blocks
  * @wake_state:		Wakeup state to use (TASK_NORMAL or TASK_RTLOCK_WAIT)
- * @prio:		Priority of the waiter
- * @deadline:		Deadline of the waiter if applicable
  * @ww_ctx:		WW context pointer
+ *
+ * @tree is ordered by @lock->wait_lock
+ * @pi_tree is ordered by rt_mutex_owner(@lock)->pi_lock
  */
 struct rt_mutex_waiter {
-	struct rb_node		tree_entry;
-	struct rb_node		pi_tree_entry;
+	struct rt_waiter_node	tree;
+	struct rt_waiter_node	pi_tree;
 	struct task_struct	*task;
 	struct rt_mutex_base	*lock;
 	unsigned int		wake_state;
-	int			prio;
-	u64			deadline;
 	struct ww_acquire_ctx	*ww_ctx;
 };
 
@@ -105,7 +122,7 @@
 {
 	struct rb_node *leftmost = rb_first_cached(&lock->waiters);
 
-	return rb_entry(leftmost, struct rt_mutex_waiter, tree_entry) == waiter;
+	return rb_entry(leftmost, struct rt_mutex_waiter, tree.entry) == waiter;
 }
 
 static inline struct rt_mutex_waiter *rt_mutex_top_waiter(struct rt_mutex_base *lock)
@@ -113,8 +130,10 @@
 	struct rb_node *leftmost = rb_first_cached(&lock->waiters);
 	struct rt_mutex_waiter *w = NULL;
 
+	lockdep_assert_held(&lock->wait_lock);
+
 	if (leftmost) {
-		w = rb_entry(leftmost, struct rt_mutex_waiter, tree_entry);
+		w = rb_entry(leftmost, struct rt_mutex_waiter, tree.entry);
 		BUG_ON(w->lock != lock);
 	}
 	return w;
@@ -127,8 +146,10 @@
 
 static inline struct rt_mutex_waiter *task_top_pi_waiter(struct task_struct *p)
 {
+	lockdep_assert_held(&p->pi_lock);
+
 	return rb_entry(p->pi_waiters.rb_leftmost, struct rt_mutex_waiter,
-			pi_tree_entry);
+			pi_tree.entry);
 }
 
 #define RT_MUTEX_HAS_WAITERS	1UL
@@ -190,8 +211,8 @@
 static inline void rt_mutex_init_waiter(struct rt_mutex_waiter *waiter)
 {
 	debug_rt_mutex_init_waiter(waiter);
-	RB_CLEAR_NODE(&waiter->pi_tree_entry);
-	RB_CLEAR_NODE(&waiter->tree_entry);
+	RB_CLEAR_NODE(&waiter->pi_tree.entry);
+	RB_CLEAR_NODE(&waiter->tree.entry);
 	waiter->wake_state = TASK_NORMAL;
 	waiter->task = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/rwsem.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/rwsem.c
@@ -106,9 +106,9 @@
  * atomic_long_cmpxchg() will be used to obtain writer lock.
  *
  * There are three places where the lock handoff bit may be set or cleared.
- * 1) rwsem_mark_wake() for readers.
- * 2) rwsem_try_write_lock() for writers.
- * 3) Error path of rwsem_down_write_slowpath().
+ * 1) rwsem_mark_wake() for readers		-- set, clear
+ * 2) rwsem_try_write_lock() for writers	-- set, clear
+ * 3) rwsem_del_waiter()			-- clear
  *
  * For all the above cases, wait_lock will be held. A writer must also
  * be the first one in the wait_list to be eligible for setting the handoff
@@ -133,14 +133,19 @@
  * the owner value concurrently without lock. Read from owner, however,
  * may not need READ_ONCE() as long as the pointer value is only used
  * for comparison and isn't being dereferenced.
+ *
+ * Both rwsem_{set,clear}_owner() functions should be in the same
+ * preempt disable section as the atomic op that changes sem->count.
  */
 static inline void rwsem_set_owner(struct rw_semaphore *sem)
 {
+	lockdep_assert_preemption_disabled();
 	atomic_long_set(&sem->owner, (long)current);
 }
 
 static inline void rwsem_clear_owner(struct rw_semaphore *sem)
 {
+	lockdep_assert_preemption_disabled();
 	atomic_long_set(&sem->owner, 0);
 }
 
@@ -251,13 +256,16 @@
 static inline bool rwsem_write_trylock(struct rw_semaphore *sem)
 {
 	long tmp = RWSEM_UNLOCKED_VALUE;
+	bool ret = false;
 
+	preempt_disable();
 	if (atomic_long_try_cmpxchg_acquire(&sem->count, &tmp, RWSEM_WRITER_LOCKED)) {
 		rwsem_set_owner(sem);
-		return true;
+		ret = true;
 	}
 
-	return false;
+	preempt_enable();
+	return ret;
 }
 
 /*
@@ -335,6 +343,7 @@
 	struct task_struct *task;
 	enum rwsem_waiter_type type;
 	unsigned long timeout;
+	bool handoff_set;
 };
 #define rwsem_first_waiter(sem) \
 	list_first_entry(&sem->wait_list, struct rwsem_waiter, list)
@@ -345,12 +354,6 @@
 	RWSEM_WAKE_READ_OWNED	/* Waker thread holds the read lock */
 };
 
-enum writer_wait_state {
-	WRITER_NOT_FIRST,	/* Writer is not first in wait list */
-	WRITER_FIRST,		/* Writer is first in wait list     */
-	WRITER_HANDOFF		/* Writer is first & handoff needed */
-};
-
 /*
  * The typical HZ value is either 250 or 1000. So set the minimum waiting
  * time to at least 4ms or 1 jiffy (if it is higher than 4ms) in the wait
@@ -366,6 +369,31 @@
  */
 #define MAX_READERS_WAKEUP	0x100
 
+static inline void
+rwsem_add_waiter(struct rw_semaphore *sem, struct rwsem_waiter *waiter)
+{
+	lockdep_assert_held(&sem->wait_lock);
+	list_add_tail(&waiter->list, &sem->wait_list);
+	/* caller will set RWSEM_FLAG_WAITERS */
+}
+
+/*
+ * Remove a waiter from the wait_list and clear flags.
+ *
+ * Both rwsem_mark_wake() and rwsem_try_write_lock() contain a full 'copy' of
+ * this function. Modify with care.
+ */
+static inline void
+rwsem_del_waiter(struct rw_semaphore *sem, struct rwsem_waiter *waiter)
+{
+	lockdep_assert_held(&sem->wait_lock);
+	list_del(&waiter->list);
+	if (likely(!list_empty(&sem->wait_list)))
+		return;
+
+	atomic_long_andnot(RWSEM_FLAG_HANDOFF | RWSEM_FLAG_WAITERS, &sem->count);
+}
+
 /*
  * handle the lock release when processes blocked on it that can now run
  * - if we come here from up_xxxx(), then the RWSEM_FLAG_WAITERS bit must
@@ -377,6 +405,8 @@
  *   preferably when the wait_lock is released
  * - woken process blocks are discarded from the list after having task zeroed
  * - writers are only marked woken if downgrading is false
+ *
+ * Implies rwsem_del_waiter() for all woken readers.
  */
 static void rwsem_mark_wake(struct rw_semaphore *sem,
 			    enum rwsem_wake_type wake_type,
@@ -432,10 +462,12 @@
 			 * to give up the lock), request a HANDOFF to
 			 * force the issue.
 			 */
-			if (!(oldcount & RWSEM_FLAG_HANDOFF) &&
-			    time_after(jiffies, waiter->timeout)) {
-				adjustment -= RWSEM_FLAG_HANDOFF;
-				lockevent_inc(rwsem_rlock_handoff);
+			if (time_after(jiffies, waiter->timeout)) {
+				if (!(oldcount & RWSEM_FLAG_HANDOFF)) {
+					adjustment -= RWSEM_FLAG_HANDOFF;
+					lockevent_inc(rwsem_rlock_handoff);
+				}
+				waiter->handoff_set = true;
 			}
 
 			atomic_long_add(-adjustment, &sem->count);
@@ -491,18 +523,25 @@
 
 	adjustment = woken * RWSEM_READER_BIAS - adjustment;
 	lockevent_cond_inc(rwsem_wake_reader, woken);
+
+	oldcount = atomic_long_read(&sem->count);
 	if (list_empty(&sem->wait_list)) {
-		/* hit end of list above */
+		/*
+		 * Combined with list_move_tail() above, this implies
+		 * rwsem_del_waiter().
+		 */
 		adjustment -= RWSEM_FLAG_WAITERS;
+		if (oldcount & RWSEM_FLAG_HANDOFF)
+			adjustment -= RWSEM_FLAG_HANDOFF;
+	} else if (woken) {
+		/*
+		 * When we've woken a reader, we no longer need to force
+		 * writers to give up the lock and we can clear HANDOFF.
+		 */
+		if (oldcount & RWSEM_FLAG_HANDOFF)
+			adjustment -= RWSEM_FLAG_HANDOFF;
 	}
 
-	/*
-	 * When we've woken a reader, we no longer need to force writers
-	 * to give up the lock and we can clear HANDOFF.
-	 */
-	if (woken && (atomic_long_read(&sem->count) & RWSEM_FLAG_HANDOFF))
-		adjustment -= RWSEM_FLAG_HANDOFF;
-
 	if (adjustment)
 		atomic_long_add(adjustment, &sem->count);
 
@@ -533,12 +572,12 @@
  * race conditions between checking the rwsem wait list and setting the
  * sem->count accordingly.
  *
- * If wstate is WRITER_HANDOFF, it will make sure that either the handoff
- * bit is set or the lock is acquired with handoff bit cleared.
+ * Implies rwsem_del_waiter() on success.
  */
 static inline bool rwsem_try_write_lock(struct rw_semaphore *sem,
-					enum writer_wait_state wstate)
+					struct rwsem_waiter *waiter)
 {
+	struct rwsem_waiter *first = rwsem_first_waiter(sem);
 	long count, new;
 
 	lockdep_assert_held(&sem->wait_lock);
@@ -547,13 +586,26 @@
 	do {
 		bool has_handoff = !!(count & RWSEM_FLAG_HANDOFF);
 
-		if (has_handoff && wstate == WRITER_NOT_FIRST)
-			return false;
+		if (has_handoff) {
+			/*
+			 * Honor handoff bit and yield only when the first
+			 * waiter is the one that set it. Otherwisee, we
+			 * still try to acquire the rwsem.
+			 */
+			if (first->handoff_set && (waiter != first))
+				return false;
+		}
 
 		new = count;
 
 		if (count & RWSEM_LOCK_MASK) {
-			if (has_handoff || (wstate != WRITER_HANDOFF))
+			/*
+			 * A waiter (first or not) can set the handoff bit
+			 * if it is an RT task or wait in the wait queue
+			 * for too long.
+			 */
+			if (has_handoff || (!rt_task(waiter->task) &&
+					    !time_after(jiffies, waiter->timeout)))
 				return false;
 
 			new |= RWSEM_FLAG_HANDOFF;
@@ -567,16 +619,43 @@
 	} while (!atomic_long_try_cmpxchg_acquire(&sem->count, &count, new));
 
 	/*
-	 * We have either acquired the lock with handoff bit cleared or
-	 * set the handoff bit.
+	 * We have either acquired the lock with handoff bit cleared or set
+	 * the handoff bit. Only the first waiter can have its handoff_set
+	 * set here to enable optimistic spinning in slowpath loop.
 	 */
-	if (new & RWSEM_FLAG_HANDOFF)
+	if (new & RWSEM_FLAG_HANDOFF) {
+		first->handoff_set = true;
+		lockevent_inc(rwsem_wlock_handoff);
 		return false;
+	}
 
+	/*
+	 * Have rwsem_try_write_lock() fully imply rwsem_del_waiter() on
+	 * success.
+	 */
+	list_del(&waiter->list);
 	rwsem_set_owner(sem);
 	return true;
 }
 
+/*
+ * The rwsem_spin_on_owner() function returns the following 4 values
+ * depending on the lock owner state.
+ *   OWNER_NULL  : owner is currently NULL
+ *   OWNER_WRITER: when owner changes and is a writer
+ *   OWNER_READER: when owner changes and the new owner may be a reader.
+ *   OWNER_NONSPINNABLE:
+ *		   when optimistic spinning has to stop because either the
+ *		   owner stops running, is unknown, or its timeslice has
+ *		   been used up.
+ */
+enum owner_state {
+	OWNER_NULL		= 1 << 0,
+	OWNER_WRITER		= 1 << 1,
+	OWNER_READER		= 1 << 2,
+	OWNER_NONSPINNABLE	= 1 << 3,
+};
+
 #ifdef CONFIG_RWSEM_SPIN_ON_OWNER
 /*
  * Try to acquire write lock before the writer has been put on wait queue.
@@ -632,23 +711,6 @@
 	return ret;
 }
 
-/*
- * The rwsem_spin_on_owner() function returns the following 4 values
- * depending on the lock owner state.
- *   OWNER_NULL  : owner is currently NULL
- *   OWNER_WRITER: when owner changes and is a writer
- *   OWNER_READER: when owner changes and the new owner may be a reader.
- *   OWNER_NONSPINNABLE:
- *		   when optimistic spinning has to stop because either the
- *		   owner stops running, is unknown, or its timeslice has
- *		   been used up.
- */
-enum owner_state {
-	OWNER_NULL		= 1 << 0,
-	OWNER_WRITER		= 1 << 1,
-	OWNER_READER		= 1 << 2,
-	OWNER_NONSPINNABLE	= 1 << 3,
-};
 #define OWNER_SPINNABLE		(OWNER_NULL | OWNER_WRITER | OWNER_READER)
 
 static inline enum owner_state
@@ -878,12 +940,11 @@
 
 static inline void clear_nonspinnable(struct rw_semaphore *sem) { }
 
-static inline int
+static inline enum owner_state
 rwsem_spin_on_owner(struct rw_semaphore *sem)
 {
-	return 0;
+	return OWNER_NONSPINNABLE;
 }
-#define OWNER_NULL	1
 #endif
 
 /*
@@ -933,6 +994,7 @@
 	waiter.task = current;
 	waiter.type = RWSEM_WAITING_FOR_READ;
 	waiter.timeout = jiffies + RWSEM_WAIT_TIMEOUT;
+	waiter.handoff_set = false;
 
 	raw_spin_lock_irq(&sem->wait_lock);
 	if (list_empty(&sem->wait_list)) {
@@ -953,7 +1015,7 @@
 		}
 		adjustment += RWSEM_FLAG_WAITERS;
 	}
-	list_add_tail(&waiter.list, &sem->wait_list);
+	rwsem_add_waiter(sem, &waiter);
 
 	/* we're now waiting on the lock, but no longer actively locking */
 	count = atomic_long_add_return(adjustment, &sem->count);
@@ -990,7 +1052,7 @@
 			/* Ordered by sem->wait_lock against rwsem_mark_wake(). */
 			break;
 		}
-		schedule();
+		schedule_preempt_disabled();
 		lockevent_inc(rwsem_sleep_reader);
 	}
 
@@ -999,11 +1061,7 @@
 	return sem;
 
 out_nolock:
-	list_del(&waiter.list);
-	if (list_empty(&sem->wait_list)) {
-		atomic_long_andnot(RWSEM_FLAG_WAITERS|RWSEM_FLAG_HANDOFF,
-				   &sem->count);
-	}
+	rwsem_del_waiter(sem, &waiter);
 	raw_spin_unlock_irq(&sem->wait_lock);
 	__set_current_state(TASK_RUNNING);
 	lockevent_inc(rwsem_rlock_fail);
@@ -1017,9 +1075,7 @@
 rwsem_down_write_slowpath(struct rw_semaphore *sem, int state)
 {
 	long count;
-	enum writer_wait_state wstate;
 	struct rwsem_waiter waiter;
-	struct rw_semaphore *ret = sem;
 	DEFINE_WAKE_Q(wake_q);
 
 	/* do optimistic spinning and steal lock if possible */
@@ -1035,16 +1091,13 @@
 	waiter.task = current;
 	waiter.type = RWSEM_WAITING_FOR_WRITE;
 	waiter.timeout = jiffies + RWSEM_WAIT_TIMEOUT;
+	waiter.handoff_set = false;
 
 	raw_spin_lock_irq(&sem->wait_lock);
-
-	/* account for this before adding a new element to the list */
-	wstate = list_empty(&sem->wait_list) ? WRITER_FIRST : WRITER_NOT_FIRST;
-
-	list_add_tail(&waiter.list, &sem->wait_list);
+	rwsem_add_waiter(sem, &waiter);
 
 	/* we're now waiting on the lock */
-	if (wstate == WRITER_NOT_FIRST) {
+	if (rwsem_first_waiter(sem) != &waiter) {
 		count = atomic_long_read(&sem->count);
 
 		/*
@@ -1080,13 +1133,16 @@
 	/* wait until we successfully acquire the lock */
 	set_current_state(state);
 	for (;;) {
-		if (rwsem_try_write_lock(sem, wstate)) {
+		if (rwsem_try_write_lock(sem, &waiter)) {
 			/* rwsem_try_write_lock() implies ACQUIRE on success */
 			break;
 		}
 
 		raw_spin_unlock_irq(&sem->wait_lock);
 
+		if (signal_pending_state(state, current))
+			goto out_nolock;
+
 		/*
 		 * After setting the handoff bit and failing to acquire
 		 * the lock, attempt to spin on owner to accelerate lock
@@ -1095,70 +1151,37 @@
 		 * In this case, we attempt to acquire the lock again
 		 * without sleeping.
 		 */
-		if (wstate == WRITER_HANDOFF &&
-		    rwsem_spin_on_owner(sem) == OWNER_NULL)
-			goto trylock_again;
-
-		/* Block until there are no active lockers. */
-		for (;;) {
-			if (signal_pending_state(state, current))
-				goto out_nolock;
-
-			schedule();
-			lockevent_inc(rwsem_sleep_writer);
-			set_current_state(state);
-			/*
-			 * If HANDOFF bit is set, unconditionally do
-			 * a trylock.
-			 */
-			if (wstate == WRITER_HANDOFF)
-				break;
-
-			if ((wstate == WRITER_NOT_FIRST) &&
-			    (rwsem_first_waiter(sem) == &waiter))
-				wstate = WRITER_FIRST;
+		if (waiter.handoff_set) {
+			enum owner_state owner_state;
 
-			count = atomic_long_read(&sem->count);
-			if (!(count & RWSEM_LOCK_MASK))
-				break;
+			preempt_disable();
+			owner_state = rwsem_spin_on_owner(sem);
+			preempt_enable();
 
-			/*
-			 * The setting of the handoff bit is deferred
-			 * until rwsem_try_write_lock() is called.
-			 */
-			if ((wstate == WRITER_FIRST) && (rt_task(current) ||
-			    time_after(jiffies, waiter.timeout))) {
-				wstate = WRITER_HANDOFF;
-				lockevent_inc(rwsem_wlock_handoff);
-				break;
-			}
+			if (owner_state == OWNER_NULL)
+				goto trylock_again;
 		}
+
+		schedule();
+		lockevent_inc(rwsem_sleep_writer);
+		set_current_state(state);
 trylock_again:
 		raw_spin_lock_irq(&sem->wait_lock);
 	}
 	__set_current_state(TASK_RUNNING);
-	list_del(&waiter.list);
 	raw_spin_unlock_irq(&sem->wait_lock);
 	lockevent_inc(rwsem_wlock);
-
-	return ret;
+	return sem;
 
 out_nolock:
 	__set_current_state(TASK_RUNNING);
 	raw_spin_lock_irq(&sem->wait_lock);
-	list_del(&waiter.list);
-
-	if (unlikely(wstate == WRITER_HANDOFF))
-		atomic_long_add(-RWSEM_FLAG_HANDOFF,  &sem->count);
-
-	if (list_empty(&sem->wait_list))
-		atomic_long_andnot(RWSEM_FLAG_WAITERS, &sem->count);
-	else
+	rwsem_del_waiter(sem, &waiter);
+	if (!list_empty(&sem->wait_list))
 		rwsem_mark_wake(sem, RWSEM_WAKE_ANY, &wake_q);
 	raw_spin_unlock_irq(&sem->wait_lock);
 	wake_up_q(&wake_q);
 	lockevent_inc(rwsem_wlock_fail);
-
 	return ERR_PTR(-EINTR);
 }
 
@@ -1206,57 +1229,64 @@
 /*
  * lock for reading
  */
-static inline int __down_read_common(struct rw_semaphore *sem, int state)
+static __always_inline int __down_read_common(struct rw_semaphore *sem, int state)
 {
+	int ret = 0;
 	long count;
 
+	preempt_disable();
 	if (!rwsem_read_trylock(sem, &count)) {
-		if (IS_ERR(rwsem_down_read_slowpath(sem, count, state)))
-			return -EINTR;
+		if (IS_ERR(rwsem_down_read_slowpath(sem, count, state))) {
+			ret = -EINTR;
+			goto out;
+		}
 		DEBUG_RWSEMS_WARN_ON(!is_rwsem_reader_owned(sem), sem);
 	}
-	return 0;
+out:
+	preempt_enable();
+	return ret;
 }
 
-static inline void __down_read(struct rw_semaphore *sem)
+static __always_inline void __down_read(struct rw_semaphore *sem)
 {
 	__down_read_common(sem, TASK_UNINTERRUPTIBLE);
 }
 
-static inline int __down_read_interruptible(struct rw_semaphore *sem)
+static __always_inline int __down_read_interruptible(struct rw_semaphore *sem)
 {
 	return __down_read_common(sem, TASK_INTERRUPTIBLE);
 }
 
-static inline int __down_read_killable(struct rw_semaphore *sem)
+static __always_inline int __down_read_killable(struct rw_semaphore *sem)
 {
 	return __down_read_common(sem, TASK_KILLABLE);
 }
 
 static inline int __down_read_trylock(struct rw_semaphore *sem)
 {
+	int ret = 0;
 	long tmp;
 
 	DEBUG_RWSEMS_WARN_ON(sem->magic != sem, sem);
 
-	/*
-	 * Optimize for the case when the rwsem is not locked at all.
-	 */
-	tmp = RWSEM_UNLOCKED_VALUE;
-	do {
+	preempt_disable();
+	tmp = atomic_long_read(&sem->count);
+	while (!(tmp & RWSEM_READ_FAILED_MASK)) {
 		if (atomic_long_try_cmpxchg_acquire(&sem->count, &tmp,
-					tmp + RWSEM_READER_BIAS)) {
+						    tmp + RWSEM_READER_BIAS)) {
 			rwsem_set_reader_owned(sem);
-			return 1;
+			ret = 1;
+			break;
 		}
-	} while (!(tmp & RWSEM_READ_FAILED_MASK));
-	return 0;
+	}
+	preempt_enable();
+	return ret;
 }
 
 /*
  * lock for writing
  */
-static inline int __down_write_common(struct rw_semaphore *sem, int state)
+static __always_inline int __down_write_common(struct rw_semaphore *sem, int state)
 {
 	if (unlikely(!rwsem_write_trylock(sem))) {
 		if (IS_ERR(rwsem_down_write_slowpath(sem, state)))
@@ -1266,12 +1296,12 @@
 	return 0;
 }
 
-static inline void __down_write(struct rw_semaphore *sem)
+static __always_inline void __down_write(struct rw_semaphore *sem)
 {
 	__down_write_common(sem, TASK_UNINTERRUPTIBLE);
 }
 
-static inline int __down_write_killable(struct rw_semaphore *sem)
+static __always_inline int __down_write_killable(struct rw_semaphore *sem)
 {
 	return __down_write_common(sem, TASK_KILLABLE);
 }
@@ -1292,6 +1322,7 @@
 	DEBUG_RWSEMS_WARN_ON(sem->magic != sem, sem);
 	DEBUG_RWSEMS_WARN_ON(!is_rwsem_reader_owned(sem), sem);
 
+	preempt_disable();
 	rwsem_clear_reader_owned(sem);
 	tmp = atomic_long_add_return_release(-RWSEM_READER_BIAS, &sem->count);
 	DEBUG_RWSEMS_WARN_ON(tmp < 0, sem);
@@ -1300,6 +1331,7 @@
 		clear_nonspinnable(sem);
 		rwsem_wake(sem);
 	}
+	preempt_enable();
 }
 
 /*
@@ -1317,8 +1349,10 @@
 	DEBUG_RWSEMS_WARN_ON((rwsem_owner(sem) != current) &&
 			    !rwsem_test_oflags(sem, RWSEM_NONSPINNABLE), sem);
 
+	preempt_disable();
 	rwsem_clear_owner(sem);
 	tmp = atomic_long_fetch_add_release(-RWSEM_WRITER_LOCKED, &sem->count);
+	preempt_enable();
 	if (unlikely(tmp & RWSEM_FLAG_WAITERS))
 		rwsem_wake(sem);
 }
@@ -1617,6 +1651,12 @@
 {
 	might_sleep();
 	__down_read(sem);
+	/*
+	 * The owner value for a reader-owned lock is mostly for debugging
+	 * purpose only and is not critical to the correct functioning of
+	 * rwsem. So it is perfectly fine to set it in a preempt-enabled
+	 * context here.
+	 */
 	__rwsem_set_reader_owned(sem, NULL);
 }
 EXPORT_SYMBOL(down_read_non_owner);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/semaphore.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/semaphore.c
@@ -29,6 +29,7 @@
 #include <linux/export.h>
 #include <linux/sched.h>
 #include <linux/sched/debug.h>
+#include <linux/sched/wake_q.h>
 #include <linux/semaphore.h>
 #include <linux/spinlock.h>
 #include <linux/ftrace.h>
@@ -37,7 +38,7 @@
 static noinline int __down_interruptible(struct semaphore *sem);
 static noinline int __down_killable(struct semaphore *sem);
 static noinline int __down_timeout(struct semaphore *sem, long timeout);
-static noinline void __up(struct semaphore *sem);
+static noinline void __up(struct semaphore *sem, struct wake_q_head *wake_q);
 
 /**
  * down - acquire the semaphore
@@ -182,13 +183,16 @@
 void up(struct semaphore *sem)
 {
 	unsigned long flags;
+	DEFINE_WAKE_Q(wake_q);
 
 	raw_spin_lock_irqsave(&sem->lock, flags);
 	if (likely(list_empty(&sem->wait_list)))
 		sem->count++;
 	else
-		__up(sem);
+		__up(sem, &wake_q);
 	raw_spin_unlock_irqrestore(&sem->lock, flags);
+	if (!wake_q_empty(&wake_q))
+		wake_up_q(&wake_q);
 }
 EXPORT_SYMBOL(up);
 
@@ -256,11 +260,12 @@
 	return __down_common(sem, TASK_UNINTERRUPTIBLE, timeout);
 }
 
-static noinline void __sched __up(struct semaphore *sem)
+static noinline void __sched __up(struct semaphore *sem,
+				  struct wake_q_head *wake_q)
 {
 	struct semaphore_waiter *waiter = list_first_entry(&sem->wait_list,
 						struct semaphore_waiter, list);
 	list_del(&waiter->list);
 	waiter->up = true;
-	wake_up_process(waiter->task);
+	wake_q_add(wake_q, waiter->task);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/test-ww_mutex.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/test-ww_mutex.c
@@ -426,7 +426,6 @@
 	} while (!time_after(jiffies, stress->timeout));
 
 	kfree(order);
-	kfree(stress);
 }
 
 struct reorder_lock {
@@ -491,7 +490,6 @@
 	list_for_each_entry_safe(ll, ln, &locks, link)
 		kfree(ll);
 	kfree(order);
-	kfree(stress);
 }
 
 static void stress_one_work(struct work_struct *work)
@@ -512,8 +510,6 @@
 			break;
 		}
 	} while (!time_after(jiffies, stress->timeout));
-
-	kfree(stress);
 }
 
 #define STRESS_INORDER BIT(0)
@@ -524,15 +520,24 @@
 static int stress(int nlocks, int nthreads, unsigned int flags)
 {
 	struct ww_mutex *locks;
-	int n;
+	struct stress *stress_array;
+	int n, count;
 
 	locks = kmalloc_array(nlocks, sizeof(*locks), GFP_KERNEL);
 	if (!locks)
 		return -ENOMEM;
 
+	stress_array = kmalloc_array(nthreads, sizeof(*stress_array),
+				     GFP_KERNEL);
+	if (!stress_array) {
+		kfree(locks);
+		return -ENOMEM;
+	}
+
 	for (n = 0; n < nlocks; n++)
 		ww_mutex_init(&locks[n], &ww_class);
 
+	count = 0;
 	for (n = 0; nthreads; n++) {
 		struct stress *stress;
 		void (*fn)(struct work_struct *work);
@@ -556,9 +561,7 @@
 		if (!fn)
 			continue;
 
-		stress = kmalloc(sizeof(*stress), GFP_KERNEL);
-		if (!stress)
-			break;
+		stress = &stress_array[count++];
 
 		INIT_WORK(&stress->work, fn);
 		stress->locks = locks;
@@ -573,6 +576,7 @@
 
 	for (n = 0; n < nlocks; n++)
 		ww_mutex_destroy(&locks[n]);
+	kfree(stress_array);
 	kfree(locks);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/locking/ww_mutex.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/locking/ww_mutex.h
@@ -96,25 +96,25 @@
 	struct rb_node *n = rb_first(&lock->rtmutex.waiters.rb_root);
 	if (!n)
 		return NULL;
-	return rb_entry(n, struct rt_mutex_waiter, tree_entry);
+	return rb_entry(n, struct rt_mutex_waiter, tree.entry);
 }
 
 static inline struct rt_mutex_waiter *
 __ww_waiter_next(struct rt_mutex *lock, struct rt_mutex_waiter *w)
 {
-	struct rb_node *n = rb_next(&w->tree_entry);
+	struct rb_node *n = rb_next(&w->tree.entry);
 	if (!n)
 		return NULL;
-	return rb_entry(n, struct rt_mutex_waiter, tree_entry);
+	return rb_entry(n, struct rt_mutex_waiter, tree.entry);
 }
 
 static inline struct rt_mutex_waiter *
 __ww_waiter_prev(struct rt_mutex *lock, struct rt_mutex_waiter *w)
 {
-	struct rb_node *n = rb_prev(&w->tree_entry);
+	struct rb_node *n = rb_prev(&w->tree.entry);
 	if (!n)
 		return NULL;
-	return rb_entry(n, struct rt_mutex_waiter, tree_entry);
+	return rb_entry(n, struct rt_mutex_waiter, tree.entry);
 }
 
 static inline struct rt_mutex_waiter *
@@ -123,7 +123,7 @@
 	struct rb_node *n = rb_last(&lock->rtmutex.waiters.rb_root);
 	if (!n)
 		return NULL;
-	return rb_entry(n, struct rt_mutex_waiter, tree_entry);
+	return rb_entry(n, struct rt_mutex_waiter, tree.entry);
 }
 
 static inline void
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/module.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/module.c
@@ -335,14 +335,14 @@
 
 /*
  * A thread that wants to hold a reference to a module only while it
- * is running can call this to safely exit.  nfsd and lockd use this.
+ * is running can call this to safely exit.
  */
-void __noreturn __module_put_and_exit(struct module *mod, long code)
+void __noreturn __module_put_and_kthread_exit(struct module *mod, long code)
 {
 	module_put(mod);
-	do_exit(code);
+	kthread_exit(code);
 }
-EXPORT_SYMBOL(__module_put_and_exit);
+EXPORT_SYMBOL(__module_put_and_kthread_exit);
 
 /* Find a module section: 0 means not found. */
 static unsigned int find_sec(const struct load_info *info, const char *name)
@@ -2407,7 +2407,7 @@
 	return ret;
 }
 
-static bool module_init_layout_section(const char *sname)
+bool module_init_layout_section(const char *sname)
 {
 #ifndef CONFIG_MODULE_UNLOAD
 	if (module_exit_section(sname))
@@ -2967,14 +2967,29 @@
 	Elf_Shdr *shdr, *strhdr;
 	int err;
 
-	if (info->len < sizeof(*(info->hdr)))
-		return -ENOEXEC;
-
-	if (memcmp(info->hdr->e_ident, ELFMAG, SELFMAG) != 0
-	    || info->hdr->e_type != ET_REL
-	    || !elf_check_arch(info->hdr)
-	    || info->hdr->e_shentsize != sizeof(Elf_Shdr))
-		return -ENOEXEC;
+	if (info->len < sizeof(*(info->hdr))) {
+		pr_err("Invalid ELF header len %lu\n", info->len);
+		goto no_exec;
+	}
+
+	if (memcmp(info->hdr->e_ident, ELFMAG, SELFMAG) != 0) {
+		pr_err("Invalid ELF header magic: != %s\n", ELFMAG);
+		goto no_exec;
+	}
+	if (info->hdr->e_type != ET_REL) {
+		pr_err("Invalid ELF header type: %u != %u\n",
+		       info->hdr->e_type, ET_REL);
+		goto no_exec;
+	}
+	if (!elf_check_arch(info->hdr)) {
+		pr_err("Invalid architecture in ELF header: %u\n",
+		       info->hdr->e_machine);
+		goto no_exec;
+	}
+	if (info->hdr->e_shentsize != sizeof(Elf_Shdr)) {
+		pr_err("Invalid ELF section header size\n");
+		goto no_exec;
+	}
 
 	/*
 	 * e_shnum is 16 bits, and sizeof(Elf_Shdr) is
@@ -2983,8 +2998,10 @@
 	 */
 	if (info->hdr->e_shoff >= info->len
 	    || (info->hdr->e_shnum * sizeof(Elf_Shdr) >
-		info->len - info->hdr->e_shoff))
-		return -ENOEXEC;
+		info->len - info->hdr->e_shoff)) {
+		pr_err("Invalid ELF section header overflow\n");
+		goto no_exec;
+	}
 
 	info->sechdrs = (void *)info->hdr + info->hdr->e_shoff;
 
@@ -2992,13 +3009,19 @@
 	 * Verify if the section name table index is valid.
 	 */
 	if (info->hdr->e_shstrndx == SHN_UNDEF
-	    || info->hdr->e_shstrndx >= info->hdr->e_shnum)
-		return -ENOEXEC;
+	    || info->hdr->e_shstrndx >= info->hdr->e_shnum) {
+		pr_err("Invalid ELF section name index: %d || e_shstrndx (%d) >= e_shnum (%d)\n",
+		       info->hdr->e_shstrndx, info->hdr->e_shstrndx,
+		       info->hdr->e_shnum);
+		goto no_exec;
+	}
 
 	strhdr = &info->sechdrs[info->hdr->e_shstrndx];
 	err = validate_section_offset(info, strhdr);
-	if (err < 0)
+	if (err < 0) {
+		pr_err("Invalid ELF section hdr(type %u)\n", strhdr->sh_type);
 		return err;
+	}
 
 	/*
 	 * The section name table must be NUL-terminated, as required
@@ -3006,8 +3029,14 @@
 	 * strings in the section safe.
 	 */
 	info->secstrings = (void *)info->hdr + strhdr->sh_offset;
-	if (info->secstrings[strhdr->sh_size - 1] != '\0')
-		return -ENOEXEC;
+	if (strhdr->sh_size == 0) {
+		pr_err("empty section name table\n");
+		goto no_exec;
+	}
+	if (info->secstrings[strhdr->sh_size - 1] != '\0') {
+		pr_err("ELF Spec violation: section name table isn't null terminated\n");
+		goto no_exec;
+	}
 
 	/*
 	 * The code assumes that section 0 has a length of zero and
@@ -3015,8 +3044,11 @@
 	 */
 	if (info->sechdrs[0].sh_type != SHT_NULL
 	    || info->sechdrs[0].sh_size != 0
-	    || info->sechdrs[0].sh_addr != 0)
-		return -ENOEXEC;
+	    || info->sechdrs[0].sh_addr != 0) {
+		pr_err("ELF Spec violation: section 0 type(%d)!=SH_NULL or non-zero len or addr\n",
+		       info->sechdrs[0].sh_type);
+		goto no_exec;
+	}
 
 	for (i = 1; i < info->hdr->e_shnum; i++) {
 		shdr = &info->sechdrs[i];
@@ -3026,8 +3058,12 @@
 			continue;
 		case SHT_SYMTAB:
 			if (shdr->sh_link == SHN_UNDEF
-			    || shdr->sh_link >= info->hdr->e_shnum)
-				return -ENOEXEC;
+			    || shdr->sh_link >= info->hdr->e_shnum) {
+				pr_err("Invalid ELF sh_link!=SHN_UNDEF(%d) or (sh_link(%d) >= hdr->e_shnum(%d)\n",
+				       shdr->sh_link, shdr->sh_link,
+				       info->hdr->e_shnum);
+				goto no_exec;
+			}
 			fallthrough;
 		default:
 			err = validate_section_offset(info, shdr);
@@ -3049,6 +3085,9 @@
 	}
 
 	return 0;
+
+no_exec:
+	return -ENOEXEC;
 }
 
 #define COPY_CHUNK_SIZE (16*PAGE_SIZE)
@@ -3626,7 +3665,8 @@
 	sched_annotate_sleep();
 	mutex_lock(&module_mutex);
 	mod = find_module_all(name, strlen(name), true);
-	ret = !mod || mod->state == MODULE_STATE_LIVE;
+	ret = !mod || mod->state == MODULE_STATE_LIVE
+		|| mod->state == MODULE_STATE_GOING;
 	mutex_unlock(&module_mutex);
 
 	return ret;
@@ -3665,6 +3705,17 @@
 	}
 }
 
+void flush_module_init_free_work(void)
+{
+	flush_work(&init_free_wq);
+}
+
+#undef MODULE_PARAM_PREFIX
+#define MODULE_PARAM_PREFIX "module."
+/* Default value for module->async_probe_requested */
+static bool async_probe;
+module_param(async_probe, bool, 0644);
+
 /*
  * This is where the real work happens.
  *
@@ -3683,12 +3734,6 @@
 	}
 	freeinit->module_init = mod->init_layout.base;
 
-	/*
-	 * We want to find out whether @mod uses async during init.  Clear
-	 * PF_USED_ASYNC.  async_schedule*() will set it.
-	 */
-	current->flags &= ~PF_USED_ASYNC;
-
 	do_mod_ctors(mod);
 	/* Start the module */
 	if (mod->init != NULL)
@@ -3714,22 +3759,13 @@
 
 	/*
 	 * We need to finish all async code before the module init sequence
-	 * is done.  This has potential to deadlock.  For example, a newly
-	 * detected block device can trigger request_module() of the
-	 * default iosched from async probing task.  Once userland helper
-	 * reaches here, async_synchronize_full() will wait on the async
-	 * task waiting on request_module() and deadlock.
-	 *
-	 * This deadlock is avoided by perfomring async_synchronize_full()
-	 * iff module init queued any async jobs.  This isn't a full
-	 * solution as it will deadlock the same if module loading from
-	 * async jobs nests more than once; however, due to the various
-	 * constraints, this hack seems to be the best option for now.
-	 * Please refer to the following thread for details.
+	 * is done. This has potential to deadlock if synchronous module
+	 * loading is requested from async (which is not allowed!).
 	 *
-	 * http://thread.gmane.org/gmane.linux.kernel/1420814
+	 * See commit 0fdff3ec6d87 ("async, kmod: warn on synchronous
+	 * request_module() from async workers") for more details.
 	 */
-	if (!mod->async_probe_requested && (current->flags & PF_USED_ASYNC))
+	if (!mod->async_probe_requested)
 		async_synchronize_full();
 
 	ftrace_free_mem(mod, mod->init_layout.base, mod->init_layout.base +
@@ -3764,8 +3800,8 @@
 	 * Note that module_alloc() on most architectures creates W+X page
 	 * mappings which won't be cleaned up until do_free_init() runs.  Any
 	 * code such as mark_rodata_ro() which depends on those mappings to
-	 * be cleaned up needs to sync with the queued work - ie
-	 * rcu_barrier()
+	 * be cleaned up needs to sync with the queued work by invoking
+	 * flush_module_init_free_work().
 	 */
 	if (llist_add(&freeinit->node, &init_free_list))
 		schedule_work(&init_free_wq);
@@ -3811,20 +3847,35 @@
 
 	mod->state = MODULE_STATE_UNFORMED;
 
-again:
 	mutex_lock(&module_mutex);
 	old = find_module_all(mod->name, strlen(mod->name), true);
 	if (old != NULL) {
-		if (old->state != MODULE_STATE_LIVE) {
+		if (old->state == MODULE_STATE_COMING
+		    || old->state == MODULE_STATE_UNFORMED) {
 			/* Wait in case it fails to load. */
 			mutex_unlock(&module_mutex);
 			err = wait_event_interruptible(module_wq,
 					       finished_loading(mod->name));
 			if (err)
 				goto out_unlocked;
-			goto again;
+
+			/* The module might have gone in the meantime. */
+			mutex_lock(&module_mutex);
+			old = find_module_all(mod->name, strlen(mod->name),
+					      true);
 		}
-		err = -EEXIST;
+
+		/*
+		 * We are here only when the same module was being loaded. Do
+		 * not try to load it again right now. It prevents long delays
+		 * caused by serialized module load failures. It might happen
+		 * when more devices of the same type trigger load of
+		 * a particular module.
+		 */
+		if (old && old->state == MODULE_STATE_LIVE)
+			err = -EEXIST;
+		else
+			err = -EBUSY;
 		goto out;
 	}
 	mod_update_bounds(mod);
@@ -3895,7 +3946,8 @@
 	int ret;
 
 	if (strcmp(param, "async_probe") == 0) {
-		mod->async_probe_requested = true;
+		if (strtobool(val, &mod->async_probe_requested))
+			mod->async_probe_requested = true;
 		return 0;
 	}
 
@@ -3940,10 +3992,8 @@
 	 * sections.
 	 */
 	err = elf_validity_check(info);
-	if (err) {
-		pr_err("Module has invalid ELF structures\n");
+	if (err)
 		goto free_copy;
-	}
 
 	/*
 	 * Everything checks out, so set up the section info
@@ -4064,6 +4114,8 @@
 	if (err)
 		goto bug_cleanup;
 
+	mod->async_probe_requested = async_probe;
+
 	/* Module is ready to execute: parsing args may do that. */
 	after_dashes = parse_args(mod->name, mod->args, mod->kp, mod->num_kp,
 				  -32768, 32767, mod,
@@ -4436,7 +4488,6 @@
 	return ret;
 }
 
-#ifdef CONFIG_LIVEPATCH
 int module_kallsyms_on_each_symbol(int (*fn)(void *, const char *,
 					     struct module *, unsigned long),
 				   void *data)
@@ -4468,7 +4519,6 @@
 	mutex_unlock(&module_mutex);
 	return ret;
 }
-#endif /* CONFIG_LIVEPATCH */
 #endif /* CONFIG_KALLSYMS */
 
 static void cfi_init(struct module *mod)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/module_signing.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/module_signing.c
@@ -38,8 +38,15 @@
 	modlen -= sig_len + sizeof(ms);
 	info->len = modlen;
 
-	return verify_pkcs7_signature(mod, modlen, mod + modlen, sig_len,
+	ret = verify_pkcs7_signature(mod, modlen, mod + modlen, sig_len,
 				      VERIFY_USE_SECONDARY_KEYRING,
 				      VERIFYING_MODULE_SIGNATURE,
 				      NULL, NULL);
+	if (ret == -ENOKEY && IS_ENABLED(CONFIG_INTEGRITY_PLATFORM_KEYRING)) {
+		ret = verify_pkcs7_signature(mod, modlen, mod + modlen, sig_len,
+				VERIFY_USE_PLATFORM_KEYRING,
+				VERIFYING_MODULE_SIGNATURE,
+				NULL, NULL);
+	}
+	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/padata.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/padata.c
@@ -47,6 +47,22 @@
 static void padata_free_pd(struct parallel_data *pd);
 static void __init padata_mt_helper(struct work_struct *work);
 
+static inline void padata_get_pd(struct parallel_data *pd)
+{
+	refcount_inc(&pd->refcnt);
+}
+
+static inline void padata_put_pd_cnt(struct parallel_data *pd, int cnt)
+{
+	if (refcount_sub_and_test(cnt, &pd->refcnt))
+		padata_free_pd(pd);
+}
+
+static inline void padata_put_pd(struct parallel_data *pd)
+{
+	padata_put_pd_cnt(pd, 1);
+}
+
 static int padata_index_to_cpu(struct parallel_data *pd, int cpu_index)
 {
 	int cpu, target_cpu;
@@ -98,7 +114,7 @@
 {
 	int i;
 
-	spin_lock(&padata_works_lock);
+	spin_lock_bh(&padata_works_lock);
 	/* Start at 1 because the current task participates in the job. */
 	for (i = 1; i < nworks; ++i) {
 		struct padata_work *pw = padata_work_alloc();
@@ -108,7 +124,7 @@
 		padata_work_init(pw, padata_mt_helper, data, 0);
 		list_add(&pw->pw_list, head);
 	}
-	spin_unlock(&padata_works_lock);
+	spin_unlock_bh(&padata_works_lock);
 
 	return i;
 }
@@ -126,12 +142,12 @@
 	if (list_empty(works))
 		return;
 
-	spin_lock(&padata_works_lock);
+	spin_lock_bh(&padata_works_lock);
 	list_for_each_entry_safe(cur, next, works, pw_list) {
 		list_del(&cur->pw_list);
 		padata_work_free(cur);
 	}
-	spin_unlock(&padata_works_lock);
+	spin_unlock_bh(&padata_works_lock);
 }
 
 static void padata_parallel_worker(struct work_struct *parallel_work)
@@ -194,11 +210,11 @@
 		*cb_cpu = cpu;
 	}
 
-	err =  -EBUSY;
+	err = -EBUSY;
 	if ((pinst->flags & PADATA_RESET))
 		goto out;
 
-	refcount_inc(&pd->refcnt);
+	padata_get_pd(pd);
 	padata->pd = pd;
 	padata->cb_cpu = *cb_cpu;
 
@@ -207,14 +223,16 @@
 	pw = padata_work_alloc();
 	spin_unlock(&padata_works_lock);
 
+	if (!pw) {
+		/* Maximum works limit exceeded, run in the current task. */
+		padata->parallel(padata);
+	}
+
 	rcu_read_unlock_bh();
 
 	if (pw) {
 		padata_work_init(pw, padata_parallel_worker, padata, 0);
 		queue_work(pinst->parallel_wq, &pw->pw_work);
-	} else {
-		/* Maximum works limit exceeded, run in the current task. */
-		padata->parallel(padata);
 	}
 
 	return 0;
@@ -326,8 +344,14 @@
 	smp_mb();
 
 	reorder = per_cpu_ptr(pd->reorder_list, pd->cpu);
-	if (!list_empty(&reorder->list) && padata_find_next(pd, false))
+	if (!list_empty(&reorder->list) && padata_find_next(pd, false)) {
+		/*
+		 * Other context(eg. the padata_serial_worker) can finish the request.
+		 * To avoid UAF issue, add pd ref here, and put pd ref after reorder_work finish.
+		 */
+		padata_get_pd(pd);
 		queue_work(pinst->serial_wq, &pd->reorder_work);
+	}
 }
 
 static void invoke_padata_reorder(struct work_struct *work)
@@ -338,6 +362,8 @@
 	pd = container_of(work, struct parallel_data, reorder_work);
 	padata_reorder(pd);
 	local_bh_enable();
+	/* Pairs with putting the reorder_work in the serial_wq */
+	padata_put_pd(pd);
 }
 
 static void padata_serial_worker(struct work_struct *serial_work)
@@ -370,8 +396,7 @@
 	}
 	local_bh_enable();
 
-	if (refcount_sub_and_test(cnt, &pd->refcnt))
-		padata_free_pd(pd);
+	padata_put_pd_cnt(pd, cnt);
 }
 
 /**
@@ -388,13 +413,17 @@
 	int hashed_cpu = padata_cpu_hash(pd, padata->seq_nr);
 	struct padata_list *reorder = per_cpu_ptr(pd->reorder_list, hashed_cpu);
 	struct padata_priv *cur;
+	struct list_head *pos;
 
 	spin_lock(&reorder->lock);
 	/* Sort in ascending order of sequence number. */
-	list_for_each_entry_reverse(cur, &reorder->list, list)
-		if (cur->seq_nr < padata->seq_nr)
+	list_for_each_prev(pos, &reorder->list) {
+		cur = list_entry(pos, struct padata_priv, list);
+		/* Compare by difference to consider integer wrap around */
+		if ((signed int)(cur->seq_nr - padata->seq_nr) < 0)
 			break;
-	list_add(&padata->list, &cur->list);
+	}
+	list_add(&padata->list, pos);
 	spin_unlock(&reorder->lock);
 
 	/*
@@ -498,11 +527,21 @@
 	 * thread function.  Load balance large jobs between threads by
 	 * increasing the number of chunks, guarantee at least the minimum
 	 * chunk size from the caller, and honor the caller's alignment.
+	 * Ensure chunk_size is at least 1 to prevent divide-by-0
+	 * panic in padata_mt_helper().
 	 */
 	ps.chunk_size = job->size / (ps.nworks * load_balance_factor);
 	ps.chunk_size = max(ps.chunk_size, job->min_chunk);
+	ps.chunk_size = max(ps.chunk_size, 1ul);
 	ps.chunk_size = roundup(ps.chunk_size, job->align);
 
+	/*
+	 * chunk_size can be 0 if the caller sets min_chunk to 0. So force it
+	 * to at least 1 to prevent divide-by-0 panic in padata_mt_helper().`
+	 */
+	if (!ps.chunk_size)
+		ps.chunk_size = 1U;
+
 	list_for_each_entry(pw, &works, pw_list)
 		queue_work(system_unbound_wq, &pw->pw_work);
 
@@ -654,8 +693,7 @@
 	synchronize_rcu();
 
 	list_for_each_entry_continue_reverse(ps, &pinst->pslist, list)
-		if (refcount_dec_and_test(&ps->opd->refcnt))
-			padata_free_pd(ps->opd);
+		padata_put_pd(ps->opd);
 
 	pinst->flags &= ~PADATA_RESET;
 
@@ -943,7 +981,7 @@
 
 	pinst = kobj2pinst(kobj);
 	pentry = attr2pentry(attr);
-	if (pentry->show)
+	if (pentry->store)
 		ret = pentry->store(pinst, attr, buf, count);
 
 	return ret;
@@ -1089,12 +1127,21 @@
  */
 void padata_free_shell(struct padata_shell *ps)
 {
+	struct parallel_data *pd;
+
 	if (!ps)
 		return;
 
+	/*
+	 * Wait for all _do_serial calls to finish to avoid touching
+	 * freed pd's and ps's.
+	 */
+	synchronize_rcu();
+
 	mutex_lock(&ps->pinst->lock);
 	list_del(&ps->list);
-	padata_free_pd(rcu_dereference_protected(ps->pd, 1));
+	pd = rcu_dereference_protected(ps->pd, 1);
+	padata_put_pd(pd);
 	mutex_unlock(&ps->pinst->lock);
 
 	kfree(ps);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/panic.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/panic.c
@@ -32,6 +32,7 @@
 #include <linux/bug.h>
 #include <linux/ratelimit.h>
 #include <linux/debugfs.h>
+#include <linux/sysfs.h>
 #include <asm/sections.h>
 
 #define PANIC_TIMER_STEP 100
@@ -42,7 +43,9 @@
  * Should we dump all CPUs backtraces in an oops event?
  * Defaults to 0, can be changed via sysctl.
  */
-unsigned int __read_mostly sysctl_oops_all_cpu_backtrace;
+static unsigned int __read_mostly sysctl_oops_all_cpu_backtrace;
+#else
+#define sysctl_oops_all_cpu_backtrace 0
 #endif /* CONFIG_SMP */
 
 int panic_on_oops = CONFIG_PANIC_ON_OOPS_VALUE;
@@ -55,6 +58,7 @@
 int panic_on_warn __read_mostly;
 unsigned long panic_on_taint;
 bool panic_on_taint_nousertaint = false;
+static unsigned int warn_limit __read_mostly;
 
 int panic_timeout = CONFIG_PANIC_TIMEOUT;
 EXPORT_SYMBOL_GPL(panic_timeout);
@@ -71,6 +75,56 @@
 
 EXPORT_SYMBOL(panic_notifier_list);
 
+#ifdef CONFIG_SYSCTL
+static struct ctl_table kern_panic_table[] = {
+#ifdef CONFIG_SMP
+	{
+		.procname       = "oops_all_cpu_backtrace",
+		.data           = &sysctl_oops_all_cpu_backtrace,
+		.maxlen         = sizeof(int),
+		.mode           = 0644,
+		.proc_handler   = proc_dointvec_minmax,
+		.extra1         = SYSCTL_ZERO,
+		.extra2         = SYSCTL_ONE,
+	},
+#endif
+	{
+		.procname       = "warn_limit",
+		.data           = &warn_limit,
+		.maxlen         = sizeof(warn_limit),
+		.mode           = 0644,
+		.proc_handler   = proc_douintvec,
+	},
+	{ }
+};
+
+static __init int kernel_panic_sysctls_init(void)
+{
+	register_sysctl_init("kernel", kern_panic_table);
+	return 0;
+}
+late_initcall(kernel_panic_sysctls_init);
+#endif
+
+static atomic_t warn_count = ATOMIC_INIT(0);
+
+#ifdef CONFIG_SYSFS
+static ssize_t warn_count_show(struct kobject *kobj, struct kobj_attribute *attr,
+			       char *page)
+{
+	return sysfs_emit(page, "%d\n", atomic_read(&warn_count));
+}
+
+static struct kobj_attribute warn_count_attr = __ATTR_RO(warn_count);
+
+static __init int kernel_panic_sysfs_init(void)
+{
+	sysfs_add_file_to_group(kernel_kobj, &warn_count_attr.attr, NULL);
+	return 0;
+}
+late_initcall(kernel_panic_sysfs_init);
+#endif
+
 static long no_blink(int state)
 {
 	return 0;
@@ -167,6 +221,19 @@
 		ftrace_dump(DUMP_ALL);
 }
 
+void check_panic_on_warn(const char *origin)
+{
+	unsigned int limit;
+
+	if (panic_on_warn)
+		panic("%s: panic_on_warn set ...\n", origin);
+
+	limit = READ_ONCE(warn_limit);
+	if (atomic_inc_return(&warn_count) >= limit && limit)
+		panic("%s: system warned too often (kernel.warn_limit is %d)",
+		      origin, limit);
+}
+
 /**
  *	panic - halt the system
  *	@fmt: The text string to print
@@ -184,6 +251,16 @@
 	int old_cpu, this_cpu;
 	bool _crash_kexec_post_notifiers = crash_kexec_post_notifiers;
 
+	if (panic_on_warn) {
+		/*
+		 * This thread may hit another WARN() in the panic path.
+		 * Resetting this prevents additional WARN() from panicking the
+		 * system on this thread.  Other threads are blocked by the
+		 * panic_mutex in panic().
+		 */
+		panic_on_warn = 0;
+	}
+
 	/*
 	 * Disable local interrupts. This will prevent panic_smp_self_stop
 	 * from deadlocking the first cpu that invokes the panic, since
@@ -348,6 +425,14 @@
 
 	/* Do not scroll important messages printed above */
 	suppress_printk = 1;
+
+	/*
+	 * The final messages may not have been printed if in a context that
+	 * defers printing (such as NMI) and irq_work is not available.
+	 * Explicitly flush the kernel log buffer one last time.
+	 */
+	console_flush_on_panic(CONSOLE_FLUSH_PENDING);
+
 	local_irq_enable();
 	for (i = 0; ; i += PANIC_TIMER_STEP) {
 		touch_softlockup_watchdog();
@@ -592,16 +677,7 @@
 	if (regs)
 		show_regs(regs);
 
-	if (panic_on_warn) {
-		/*
-		 * This thread may hit another WARN() in the panic path.
-		 * Resetting this prevents additional WARN() from panicking the
-		 * system on this thread.  Other threads are blocked by the
-		 * panic_mutex in panic().
-		 */
-		panic_on_warn = 0;
-		panic("panic_on_warn set ...\n");
-	}
+	check_panic_on_warn("kernel");
 
 	if (!regs)
 		dump_stack();
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/pid_namespace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/pid_namespace.c
@@ -214,6 +214,7 @@
 	 */
 	do {
 		clear_thread_flag(TIF_SIGPENDING);
+		clear_thread_flag(TIF_NOTIFY_SIGNAL);
 		rc = kernel_wait4(-1, NULL, __WALL, NULL);
 	} while (rc != -ECHILD);
 
@@ -244,7 +245,24 @@
 		set_current_state(TASK_INTERRUPTIBLE);
 		if (pid_ns->pid_allocated == init_pids)
 			break;
+		/*
+		 * Release tasks_rcu_exit_srcu to avoid following deadlock:
+		 *
+		 * 1) TASK A unshare(CLONE_NEWPID)
+		 * 2) TASK A fork() twice -> TASK B (child reaper for new ns)
+		 *    and TASK C
+		 * 3) TASK B exits, kills TASK C, waits for TASK A to reap it
+		 * 4) TASK A calls synchronize_rcu_tasks()
+		 *                   -> synchronize_srcu(tasks_rcu_exit_srcu)
+		 * 5) *DEADLOCK*
+		 *
+		 * It is considered safe to release tasks_rcu_exit_srcu here
+		 * because we assume the current task can not be concurrently
+		 * reaped at this point.
+		 */
+		exit_tasks_rcu_stop();
 		schedule();
+		exit_tasks_rcu_start();
 	}
 	__set_current_state(TASK_RUNNING);
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/energy_model.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/energy_model.c
@@ -85,10 +85,7 @@
 
 static void em_debug_remove_pd(struct device *dev)
 {
-	struct dentry *debug_dir;
-
-	debug_dir = debugfs_lookup(dev_name(dev), rootdir);
-	debugfs_remove_recursive(debug_dir);
+	debugfs_lookup_and_remove(dev_name(dev), rootdir);
 }
 
 static int __init em_debug_init(void)
@@ -107,8 +104,7 @@
 static int em_create_perf_table(struct device *dev, struct em_perf_domain *pd,
 				int nr_states, struct em_data_callback *cb)
 {
-	unsigned long opp_eff, prev_opp_eff = ULONG_MAX;
-	unsigned long power, freq, prev_freq = 0;
+	unsigned long power, freq, prev_freq = 0, prev_cost = ULONG_MAX;
 	struct em_perf_state *table;
 	int i, ret;
 	u64 fmax;
@@ -153,27 +149,21 @@
 
 		table[i].power = power;
 		table[i].frequency = prev_freq = freq;
-
-		/*
-		 * The hertz/watts efficiency ratio should decrease as the
-		 * frequency grows on sane platforms. But this isn't always
-		 * true in practice so warn the user if a higher OPP is more
-		 * power efficient than a lower one.
-		 */
-		opp_eff = freq / power;
-		if (opp_eff >= prev_opp_eff)
-			dev_dbg(dev, "EM: hertz/watts ratio non-monotonically decreasing: em_perf_state %d >= em_perf_state%d\n",
-					i, i - 1);
-		prev_opp_eff = opp_eff;
 	}
 
 	/* Compute the cost of each performance state. */
 	fmax = (u64) table[nr_states - 1].frequency;
-	for (i = 0; i < nr_states; i++) {
+	for (i = nr_states - 1; i >= 0; i--) {
 		unsigned long power_res = em_scale_power(table[i].power);
 
 		table[i].cost = div64_u64(fmax * power_res,
 					  table[i].frequency);
+		if (table[i].cost >= prev_cost) {
+			dev_dbg(dev, "EM: OPP:%lu is inefficient\n",
+				table[i].frequency);
+		} else {
+			prev_cost = table[i].cost;
+		}
 	}
 
 	pd->table = table;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/hibernate.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/hibernate.c
@@ -593,7 +593,11 @@
 
 	local_irq_disable();
 	system_state = SYSTEM_SUSPEND;
-	syscore_suspend();
+
+	error = syscore_suspend();
+	if (error)
+		goto Enable_irqs;
+
 	if (pm_wakeup_pending()) {
 		error = -EAGAIN;
 		goto Power_up;
@@ -605,6 +609,7 @@
 
  Power_up:
 	syscore_resume();
+ Enable_irqs:
 	system_state = SYSTEM_RUNNING;
 	local_irq_enable();
 
@@ -640,7 +645,7 @@
 	int error;
 
 	if (hibernation_mode == HIBERNATION_SUSPEND) {
-		error = suspend_devices_and_enter(PM_SUSPEND_MEM);
+		error = suspend_devices_and_enter(mem_sleep_current);
 		if (error) {
 			hibernation_mode = hibernation_ops ?
 						HIBERNATION_PLATFORM :
@@ -691,7 +696,7 @@
 		goto Unlock;
 
 	error = swsusp_read(&flags);
-	swsusp_close(FMODE_READ);
+	swsusp_close(FMODE_READ | FMODE_EXCL);
 	if (!error)
 		error = hibernation_restore(flags & SF_PLATFORM_MODE);
 
@@ -981,7 +986,7 @@
 	/* The snapshot device should not be opened while we're running */
 	if (!hibernate_acquire()) {
 		error = -EBUSY;
-		swsusp_close(FMODE_READ);
+		swsusp_close(FMODE_READ | FMODE_EXCL);
 		goto Unlock;
 	}
 
@@ -1016,7 +1021,7 @@
 	pm_pr_dbg("Hibernation image not present or could not be loaded.\n");
 	return error;
  Close_Finish:
-	swsusp_close(FMODE_READ);
+	swsusp_close(FMODE_READ | FMODE_EXCL);
 	goto Finish;
 }
 
@@ -1326,7 +1331,7 @@
 	int rc = kstrtouint(str, 0, &resume_delay);
 
 	if (rc)
-		return rc;
+		pr_warn("resumedelay: bad option string '%s'\n", str);
 	return 1;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/main.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/main.c
@@ -504,7 +504,10 @@
 					struct kobj_attribute *attr,
 					char *buf)
 {
-	return pm_wakeup_irq ? sprintf(buf, "%u\n", pm_wakeup_irq) : -ENODATA;
+	if (!pm_wakeup_irq())
+		return -ENODATA;
+
+	return sprintf(buf, "%u\n", pm_wakeup_irq());
 }
 
 power_attr_ro(pm_wakeup_irq);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/process.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/process.c
@@ -94,7 +94,7 @@
 		       todo - wq_busy, wq_busy);
 
 		if (wq_busy)
-			show_workqueue_state();
+			show_all_workqueues();
 
 		if (!wakeup || pm_debug_messages_on) {
 			read_lock(&tasklist_lock);
@@ -134,7 +134,7 @@
 	if (!pm_freezing)
 		atomic_inc(&system_freezing_cnt);
 
-	pm_wakeup_clear(true);
+	pm_wakeup_clear(0);
 	pr_info("Freezing user space processes ... ");
 	pm_freezing = true;
 	error = try_to_freeze_tasks(true);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/snapshot.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/snapshot.c
@@ -978,8 +978,7 @@
  * Register a range of page frames the contents of which should not be saved
  * during hibernation (to be used in the early initialization code).
  */
-void __init __register_nosave_region(unsigned long start_pfn,
-				     unsigned long end_pfn, int use_kmalloc)
+void __init register_nosave_region(unsigned long start_pfn, unsigned long end_pfn)
 {
 	struct nosave_region *region;
 
@@ -995,18 +994,12 @@
 			goto Report;
 		}
 	}
-	if (use_kmalloc) {
-		/* During init, this shouldn't fail */
-		region = kmalloc(sizeof(struct nosave_region), GFP_KERNEL);
-		BUG_ON(!region);
-	} else {
-		/* This allocation cannot fail */
-		region = memblock_alloc(sizeof(struct nosave_region),
-					SMP_CACHE_BYTES);
-		if (!region)
-			panic("%s: Failed to allocate %zu bytes\n", __func__,
-			      sizeof(struct nosave_region));
-	}
+	/* This allocation cannot fail */
+	region = memblock_alloc(sizeof(struct nosave_region),
+				SMP_CACHE_BYTES);
+	if (!region)
+		panic("%s: Failed to allocate %zu bytes\n", __func__,
+		      sizeof(struct nosave_region));
 	region->start_pfn = start_pfn;
 	region->end_pfn = end_pfn;
 	list_add_tail(&region->list, &nosave_regions);
@@ -1726,8 +1719,8 @@
  * /sys/power/reserved_size, respectively).  To make this happen, we compute the
  * total number of available page frames and allocate at least
  *
- * ([page frames total] + PAGES_FOR_IO + [metadata pages]) / 2
- *  + 2 * DIV_ROUND_UP(reserved_size, PAGE_SIZE)
+ * ([page frames total] - PAGES_FOR_IO - [metadata pages]) / 2
+ *  - 2 * DIV_ROUND_UP(reserved_size, PAGE_SIZE)
  *
  * of them, which corresponds to the maximum size of a hibernation image.
  *
@@ -2421,8 +2414,9 @@
 		pbe->copy_page = tmp;
 	} else {
 		/* Copy of the page will be stored in normal memory */
-		kaddr = safe_pages_list;
-		safe_pages_list = safe_pages_list->next;
+		kaddr = __get_safe_page(ca->gfp_mask);
+		if (!kaddr)
+			return ERR_PTR(-ENOMEM);
 		pbe->copy_page = virt_to_page(kaddr);
 	}
 	pbe->next = highmem_pblist;
@@ -2602,8 +2596,9 @@
 		return ERR_PTR(-ENOMEM);
 	}
 	pbe->orig_address = page_address(page);
-	pbe->address = safe_pages_list;
-	safe_pages_list = safe_pages_list->next;
+	pbe->address = __get_safe_page(ca->gfp_mask);
+	if (!pbe->address)
+		return ERR_PTR(-ENOMEM);
 	pbe->next = restore_pblist;
 	restore_pblist = pbe;
 	return pbe->address;
@@ -2634,8 +2629,6 @@
 	if (handle->cur > 1 && handle->cur > nr_meta_pages + nr_copy_pages)
 		return 0;
 
-	handle->sync_read = 1;
-
 	if (!handle->cur) {
 		if (!buffer)
 			/* This makes the buffer be freed by swsusp_free() */
@@ -2671,7 +2664,6 @@
 			memory_bm_position_reset(&orig_bm);
 			restore_pblist = NULL;
 			handle->buffer = get_buffer(&orig_bm, &ca);
-			handle->sync_read = 0;
 			if (IS_ERR(handle->buffer))
 				return PTR_ERR(handle->buffer);
 		}
@@ -2681,9 +2673,8 @@
 		handle->buffer = get_buffer(&orig_bm, &ca);
 		if (IS_ERR(handle->buffer))
 			return PTR_ERR(handle->buffer);
-		if (handle->buffer != buffer)
-			handle->sync_read = 0;
 	}
+	handle->sync_read = (handle->buffer == buffer);
 	handle->cur++;
 	return PAGE_SIZE;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/suspend.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/suspend.c
@@ -138,8 +138,6 @@
 			break;
 		}
 
-		pm_wakeup_clear(false);
-
 		s2idle_enter();
 	}
 
@@ -189,6 +187,7 @@
 		if (mem_sleep_labels[state] &&
 		    !strcmp(str, mem_sleep_labels[state])) {
 			mem_sleep_default = state;
+			mem_sleep_current = state;
 			break;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/suspend_test.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/suspend_test.c
@@ -157,22 +157,22 @@
 	value++;
 	suspend_type = strsep(&value, ",");
 	if (!suspend_type)
-		return 0;
+		return 1;
 
 	repeat = strsep(&value, ",");
 	if (repeat) {
 		if (kstrtou32(repeat, 0, &test_repeat_count_max))
-			return 0;
+			return 1;
 	}
 
 	for (i = PM_SUSPEND_MIN; i < PM_SUSPEND_MAX; i++)
 		if (!strcmp(pm_labels[i], suspend_type)) {
 			test_state_label = pm_labels[i];
-			return 0;
+			return 1;
 		}
 
 	printk(warn_bad_state, suspend_type);
-	return 0;
+	return 1;
 }
 __setup("test_suspend", setup_test_suspend);
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/swap.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/swap.c
@@ -299,7 +299,7 @@
 	return error;
 }
 
-static blk_status_t hib_wait_io(struct hib_bio_batch *hb)
+static int hib_wait_io(struct hib_bio_batch *hb)
 {
 	/*
 	 * We are relying on the behavior of blk_plug that a thread with
@@ -603,11 +603,11 @@
 	unsigned i;
 
 	while (1) {
-		wait_event(d->go, atomic_read(&d->ready) ||
+		wait_event(d->go, atomic_read_acquire(&d->ready) ||
 		                  kthread_should_stop());
 		if (kthread_should_stop()) {
 			d->thr = NULL;
-			atomic_set(&d->stop, 1);
+			atomic_set_release(&d->stop, 1);
 			wake_up(&d->done);
 			break;
 		}
@@ -616,7 +616,7 @@
 		for (i = 0; i < d->run_threads; i++)
 			*d->crc32 = crc32_le(*d->crc32,
 			                     d->unc[i], *d->unc_len[i]);
-		atomic_set(&d->stop, 1);
+		atomic_set_release(&d->stop, 1);
 		wake_up(&d->done);
 	}
 	return 0;
@@ -646,12 +646,12 @@
 	struct cmp_data *d = data;
 
 	while (1) {
-		wait_event(d->go, atomic_read(&d->ready) ||
+		wait_event(d->go, atomic_read_acquire(&d->ready) ||
 		                  kthread_should_stop());
 		if (kthread_should_stop()) {
 			d->thr = NULL;
 			d->ret = -1;
-			atomic_set(&d->stop, 1);
+			atomic_set_release(&d->stop, 1);
 			wake_up(&d->done);
 			break;
 		}
@@ -660,7 +660,7 @@
 		d->ret = lzo1x_1_compress(d->unc, d->unc_len,
 		                          d->cmp + LZO_HEADER, &d->cmp_len,
 		                          d->wrk);
-		atomic_set(&d->stop, 1);
+		atomic_set_release(&d->stop, 1);
 		wake_up(&d->done);
 	}
 	return 0;
@@ -798,7 +798,7 @@
 
 			data[thr].unc_len = off;
 
-			atomic_set(&data[thr].ready, 1);
+			atomic_set_release(&data[thr].ready, 1);
 			wake_up(&data[thr].go);
 		}
 
@@ -806,12 +806,12 @@
 			break;
 
 		crc->run_threads = thr;
-		atomic_set(&crc->ready, 1);
+		atomic_set_release(&crc->ready, 1);
 		wake_up(&crc->go);
 
 		for (run_threads = thr, thr = 0; thr < run_threads; thr++) {
 			wait_event(data[thr].done,
-			           atomic_read(&data[thr].stop));
+				atomic_read_acquire(&data[thr].stop));
 			atomic_set(&data[thr].stop, 0);
 
 			ret = data[thr].ret;
@@ -850,7 +850,7 @@
 			}
 		}
 
-		wait_event(crc->done, atomic_read(&crc->stop));
+		wait_event(crc->done, atomic_read_acquire(&crc->stop));
 		atomic_set(&crc->stop, 0);
 	}
 
@@ -1132,12 +1132,12 @@
 	struct dec_data *d = data;
 
 	while (1) {
-		wait_event(d->go, atomic_read(&d->ready) ||
+		wait_event(d->go, atomic_read_acquire(&d->ready) ||
 		                  kthread_should_stop());
 		if (kthread_should_stop()) {
 			d->thr = NULL;
 			d->ret = -1;
-			atomic_set(&d->stop, 1);
+			atomic_set_release(&d->stop, 1);
 			wake_up(&d->done);
 			break;
 		}
@@ -1150,7 +1150,7 @@
 			flush_icache_range((unsigned long)d->unc,
 					   (unsigned long)d->unc + d->unc_len);
 
-		atomic_set(&d->stop, 1);
+		atomic_set_release(&d->stop, 1);
 		wake_up(&d->done);
 	}
 	return 0;
@@ -1338,7 +1338,7 @@
 		}
 
 		if (crc->run_threads) {
-			wait_event(crc->done, atomic_read(&crc->stop));
+			wait_event(crc->done, atomic_read_acquire(&crc->stop));
 			atomic_set(&crc->stop, 0);
 			crc->run_threads = 0;
 		}
@@ -1374,7 +1374,7 @@
 					pg = 0;
 			}
 
-			atomic_set(&data[thr].ready, 1);
+			atomic_set_release(&data[thr].ready, 1);
 			wake_up(&data[thr].go);
 		}
 
@@ -1393,7 +1393,7 @@
 
 		for (run_threads = thr, thr = 0; thr < run_threads; thr++) {
 			wait_event(data[thr].done,
-			           atomic_read(&data[thr].stop));
+				atomic_read_acquire(&data[thr].stop));
 			atomic_set(&data[thr].stop, 0);
 
 			ret = data[thr].ret;
@@ -1424,7 +1424,7 @@
 				ret = snapshot_write_next(snapshot);
 				if (ret <= 0) {
 					crc->run_threads = thr + 1;
-					atomic_set(&crc->ready, 1);
+					atomic_set_release(&crc->ready, 1);
 					wake_up(&crc->go);
 					goto out_finish;
 				}
@@ -1432,13 +1432,13 @@
 		}
 
 		crc->run_threads = thr;
-		atomic_set(&crc->ready, 1);
+		atomic_set_release(&crc->ready, 1);
 		wake_up(&crc->go);
 	}
 
 out_finish:
 	if (crc->run_threads) {
-		wait_event(crc->done, atomic_read(&crc->stop));
+		wait_event(crc->done, atomic_read_acquire(&crc->stop));
 		atomic_set(&crc->stop, 0);
 	}
 	stop = ktime_get();
@@ -1521,9 +1521,10 @@
 int swsusp_check(void)
 {
 	int error;
+	void *holder;
 
 	hib_resume_bdev = blkdev_get_by_dev(swsusp_resume_device,
-					    FMODE_READ, NULL);
+					    FMODE_READ | FMODE_EXCL, &holder);
 	if (!IS_ERR(hib_resume_bdev)) {
 		set_blocksize(hib_resume_bdev, PAGE_SIZE);
 		clear_page(swsusp_header);
@@ -1545,7 +1546,7 @@
 
 put:
 		if (error)
-			blkdev_put(hib_resume_bdev, FMODE_READ);
+			blkdev_put(hib_resume_bdev, FMODE_READ | FMODE_EXCL);
 		else
 			pr_debug("Image signature found, resuming\n");
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/user.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/user.c
@@ -26,6 +26,7 @@
 
 #include "power.h"
 
+static bool need_wait;
 
 static struct snapshot_data {
 	struct snapshot_handle handle;
@@ -78,7 +79,7 @@
 		 * Resuming.  We may need to wait for the image device to
 		 * appear.
 		 */
-		wait_for_device_probe();
+		need_wait = true;
 
 		data->swap = -1;
 		data->mode = O_WRONLY;
@@ -168,6 +169,11 @@
 	ssize_t res;
 	loff_t pg_offp = *offp & ~PAGE_MASK;
 
+	if (need_wait) {
+		wait_for_device_probe();
+		need_wait = false;
+	}
+
 	lock_system_sleep();
 
 	data = filp->private_data;
@@ -244,6 +250,11 @@
 	loff_t size;
 	sector_t offset;
 
+	if (need_wait) {
+		wait_for_device_probe();
+		need_wait = false;
+	}
+
 	if (_IOC_TYPE(cmd) != SNAPSHOT_IOC_MAGIC)
 		return -ENOTTY;
 	if (_IOC_NR(cmd) > SNAPSHOT_IOC_MAXNR)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/power/wakelock.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/power/wakelock.c
@@ -39,23 +39,20 @@
 {
 	struct rb_node *node;
 	struct wakelock *wl;
-	char *str = buf;
-	char *end = buf + PAGE_SIZE;
+	int len = 0;
 
 	mutex_lock(&wakelocks_lock);
 
 	for (node = rb_first(&wakelocks_tree); node; node = rb_next(node)) {
 		wl = rb_entry(node, struct wakelock, node);
 		if (wl->ws->active == show_active)
-			str += scnprintf(str, end - str, "%s ", wl->name);
+			len += sysfs_emit_at(buf, len, "%s ", wl->name);
 	}
-	if (str > buf)
-		str--;
 
-	str += scnprintf(str, end - str, "\n");
+	len += sysfs_emit_at(buf, len, "\n");
 
 	mutex_unlock(&wakelocks_lock);
-	return (str - buf);
+	return len;
 }
 
 #if CONFIG_PM_WAKELOCKS_LIMIT > 0
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/printk/index.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/printk/index.c
@@ -146,7 +146,7 @@
 #ifdef CONFIG_MODULES
 static void pi_remove_file(struct module *mod)
 {
-	debugfs_remove(debugfs_lookup(pi_get_module_name(mod), dfs_index));
+	debugfs_lookup_and_remove(pi_get_module_name(mod), dfs_index);
 }
 
 static int pi_module_notify(struct notifier_block *nb, unsigned long op,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/printk/printk.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/printk/printk.c
@@ -146,8 +146,10 @@
 
 static int __init control_devkmsg(char *str)
 {
-	if (__control_devkmsg(str) < 0)
+	if (__control_devkmsg(str) < 0) {
+		pr_warn("printk.devkmsg: bad option string '%s'\n", str);
 		return 1;
+	}
 
 	/*
 	 * Set sysctl string accordingly:
@@ -166,7 +168,7 @@
 	 */
 	devkmsg_log |= DEVKMSG_LOG_MASK_LOCK;
 
-	return 0;
+	return 1;
 }
 __setup("printk.devkmsg=", control_devkmsg);
 
@@ -401,7 +403,7 @@
 /* record buffer */
 #define LOG_ALIGN __alignof__(unsigned long)
 #define __LOG_BUF_LEN (1 << CONFIG_LOG_BUF_SHIFT)
-#define LOG_BUF_LEN_MAX (u32)(1 << 31)
+#define LOG_BUF_LEN_MAX ((u32)1 << 31)
 static char __log_buf[__LOG_BUF_LEN] __aligned(LOG_ALIGN);
 static char *log_buf = __log_buf;
 static u32 log_buf_len = __LOG_BUF_LEN;
@@ -455,7 +457,7 @@
 		seq = raw_read_seqcount_latch(&ls->latch);
 		idx = seq & 0x1;
 		val = ls->val[idx];
-	} while (read_seqcount_latch_retry(&ls->latch, seq));
+	} while (raw_read_seqcount_latch_retry(&ls->latch, seq));
 
 	return val;
 }
@@ -733,8 +735,19 @@
 			goto out;
 		}
 
+		/*
+		 * Guarantee this task is visible on the waitqueue before
+		 * checking the wake condition.
+		 *
+		 * The full memory barrier within set_current_state() of
+		 * prepare_to_wait_event() pairs with the full memory barrier
+		 * within wq_has_sleeper().
+		 *
+		 * This pairs with __wake_up_klogd:A.
+		 */
 		ret = wait_event_interruptible(log_wait,
-				prb_read_valid(prb, atomic64_read(&user->seq), r));
+				prb_read_valid(prb,
+					atomic64_read(&user->seq), r)); /* LMM(devkmsg_read:A) */
 		if (ret)
 			goto out;
 	}
@@ -1500,7 +1513,18 @@
 		seq = syslog_seq;
 
 		mutex_unlock(&syslog_lock);
-		len = wait_event_interruptible(log_wait, prb_read_valid(prb, seq, NULL));
+		/*
+		 * Guarantee this task is visible on the waitqueue before
+		 * checking the wake condition.
+		 *
+		 * The full memory barrier within set_current_state() of
+		 * prepare_to_wait_event() pairs with the full memory barrier
+		 * within wq_has_sleeper().
+		 *
+		 * This pairs with __wake_up_klogd:A.
+		 */
+		len = wait_event_interruptible(log_wait,
+				prb_read_valid(prb, seq, NULL)); /* LMM(syslog_print:A) */
 		mutex_lock(&syslog_lock);
 
 		if (len)
@@ -1884,6 +1908,12 @@
 	 */
 	mutex_acquire(&console_lock_dep_map, 0, 1, _THIS_IP_);
 
+	/*
+	 * Update @console_may_schedule for trylock because the previous
+	 * owner may have been schedulable.
+	 */
+	console_may_schedule = 0;
+
 	return 1;
 }
 
@@ -2245,7 +2275,11 @@
 		preempt_enable();
 	}
 
-	wake_up_klogd();
+	if (in_sched)
+		defer_console_output();
+	else
+		wake_up_klogd();
+
 	return printed_len;
 }
 EXPORT_SYMBOL(vprintk_emit);
@@ -2851,6 +2885,21 @@
 
 early_param("keep_bootcon", keep_bootcon_setup);
 
+static int console_call_setup(struct console *newcon, char *options)
+{
+	int err;
+
+	if (!newcon->setup)
+		return 0;
+
+	/* Synchronize with possible boot console. */
+	console_lock();
+	err = newcon->setup(newcon, options);
+	console_unlock();
+
+	return err;
+}
+
 /*
  * This is called by register_console() to try to match
  * the newly registered console with any of the ones selected
@@ -2860,7 +2909,8 @@
  * Care need to be taken with consoles that are statically
  * enabled such as netconsole
  */
-static int try_enable_new_console(struct console *newcon, bool user_specified)
+static int try_enable_preferred_console(struct console *newcon,
+					bool user_specified)
 {
 	struct console_cmdline *c;
 	int i, err;
@@ -2885,8 +2935,8 @@
 			if (_braille_register_console(newcon, c))
 				return 0;
 
-			if (newcon->setup &&
-			    (err = newcon->setup(newcon, c->options)) != 0)
+			err = console_call_setup(newcon, c->options);
+			if (err)
 				return err;
 		}
 		newcon->flags |= CON_ENABLED;
@@ -2908,6 +2958,23 @@
 	return -ENOENT;
 }
 
+/* Try to enable the console unconditionally */
+static void try_enable_default_console(struct console *newcon)
+{
+	if (newcon->index < 0)
+		newcon->index = 0;
+
+	if (console_call_setup(newcon, NULL) != 0)
+		return;
+
+	newcon->flags |= CON_ENABLED;
+
+	if (newcon->device) {
+		newcon->flags |= CON_CONSDEV;
+		has_preferred_console = true;
+	}
+}
+
 /*
  * The console driver calls this routine during kernel initialization
  * to register the console printing procedure with printk() and to
@@ -2963,25 +3030,15 @@
 	 *	didn't select a console we take the first one
 	 *	that registers here.
 	 */
-	if (!has_preferred_console) {
-		if (newcon->index < 0)
-			newcon->index = 0;
-		if (newcon->setup == NULL ||
-		    newcon->setup(newcon, NULL) == 0) {
-			newcon->flags |= CON_ENABLED;
-			if (newcon->device) {
-				newcon->flags |= CON_CONSDEV;
-				has_preferred_console = true;
-			}
-		}
-	}
+	if (!has_preferred_console)
+		try_enable_default_console(newcon);
 
 	/* See if this console matches one we selected on the command line */
-	err = try_enable_new_console(newcon, true);
+	err = try_enable_preferred_console(newcon, true);
 
 	/* If not, try to match against the platform default(s) */
 	if (err == -ENOENT)
-		err = try_enable_new_console(newcon, false);
+		err = try_enable_preferred_console(newcon, false);
 
 	/* printk() messages are not printed to the Braille console. */
 	if (err || newcon->flags & CON_BRL)
@@ -3213,7 +3270,7 @@
 
 static void wake_up_klogd_work_func(struct irq_work *irq_work)
 {
-	int pending = __this_cpu_xchg(printk_pending, 0);
+	int pending = this_cpu_xchg(printk_pending, 0);
 
 	if (pending & PRINTK_PENDING_OUTPUT) {
 		/* If trylock fails, someone else is doing the printing */
@@ -3228,38 +3285,75 @@
 static DEFINE_PER_CPU(struct irq_work, wake_up_klogd_work) =
 	IRQ_WORK_INIT_LAZY(wake_up_klogd_work_func);
 
-void wake_up_klogd(void)
+static void __wake_up_klogd(int val)
 {
 	if (!printk_percpu_data_ready())
 		return;
 
 	preempt_disable();
-	if (waitqueue_active(&log_wait)) {
-		this_cpu_or(printk_pending, PRINTK_PENDING_WAKEUP);
+	/*
+	 * Guarantee any new records can be seen by tasks preparing to wait
+	 * before this context checks if the wait queue is empty.
+	 *
+	 * The full memory barrier within wq_has_sleeper() pairs with the full
+	 * memory barrier within set_current_state() of
+	 * prepare_to_wait_event(), which is called after ___wait_event() adds
+	 * the waiter but before it has checked the wait condition.
+	 *
+	 * This pairs with devkmsg_read:A and syslog_print:A.
+	 */
+	if (wq_has_sleeper(&log_wait) || /* LMM(__wake_up_klogd:A) */
+	    (val & PRINTK_PENDING_OUTPUT)) {
+		this_cpu_or(printk_pending, val);
 		irq_work_queue(this_cpu_ptr(&wake_up_klogd_work));
 	}
 	preempt_enable();
 }
 
-void defer_console_output(void)
+/**
+ * wake_up_klogd - Wake kernel logging daemon
+ *
+ * Use this function when new records have been added to the ringbuffer
+ * and the console printing of those records has already occurred or is
+ * known to be handled by some other context. This function will only
+ * wake the logging daemon.
+ *
+ * Context: Any context.
+ */
+void wake_up_klogd(void)
 {
-	if (!printk_percpu_data_ready())
-		return;
-
-	preempt_disable();
-	__this_cpu_or(printk_pending, PRINTK_PENDING_OUTPUT);
-	irq_work_queue(this_cpu_ptr(&wake_up_klogd_work));
-	preempt_enable();
+	__wake_up_klogd(PRINTK_PENDING_WAKEUP);
 }
 
-int vprintk_deferred(const char *fmt, va_list args)
+/**
+ * defer_console_output - Wake kernel logging daemon and trigger
+ *	console printing in a deferred context
+ *
+ * Use this function when new records have been added to the ringbuffer,
+ * this context is responsible for console printing those records, but
+ * the current context is not allowed to perform the console printing.
+ * Trigger an irq_work context to perform the console printing. This
+ * function also wakes the logging daemon.
+ *
+ * Context: Any context.
+ */
+void defer_console_output(void)
 {
-	int r;
+	/*
+	 * New messages may have been added directly to the ringbuffer
+	 * using vprintk_store(), so wake any waiters as well.
+	 */
+	__wake_up_klogd(PRINTK_PENDING_WAKEUP | PRINTK_PENDING_OUTPUT);
+}
 
-	r = vprintk_emit(0, LOGLEVEL_SCHED, NULL, fmt, args);
+void printk_trigger_flush(void)
+{
 	defer_console_output();
+}
 
-	return r;
+int vprintk_deferred(const char *fmt, va_list args)
+{
+	return vprintk_emit(0, LOGLEVEL_SCHED, NULL, fmt, args);
 }
 
 int _printk_deferred(const char *fmt, ...)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/printk/printk_ringbuffer.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/printk/printk_ringbuffer.c
@@ -1724,7 +1724,7 @@
 	if (!buf || !buf_size)
 		return true;
 
-	data_size = min_t(u16, buf_size, len);
+	data_size = min_t(unsigned int, buf_size, len);
 
 	memcpy(&buf[0], data, data_size); /* LMM(copy_data:A) */
 	return true;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/printk/printk_safe.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/printk/printk_safe.c
@@ -38,13 +38,8 @@
 	 * Use the main logbuf even in NMI. But avoid calling console
 	 * drivers that might have their own locks.
 	 */
-	if (this_cpu_read(printk_context) || in_nmi()) {
-		int len;
-
-		len = vprintk_store(0, LOGLEVEL_DEFAULT, NULL, fmt, args);
-		defer_console_output();
-		return len;
-	}
+	if (this_cpu_read(printk_context) || in_nmi())
+		return vprintk_deferred(fmt, args);
 
 	/* No obstacles. */
 	return vprintk_default(fmt, args);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/profile.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/profile.c
@@ -57,24 +57,10 @@
 int profile_setup(char *str)
 {
 	static const char schedstr[] = "schedule";
-	static const char sleepstr[] = "sleep";
 	static const char kvmstr[] = "kvm";
 	int par;
 
-	if (!strncmp(str, sleepstr, strlen(sleepstr))) {
-#ifdef CONFIG_SCHEDSTATS
-		force_schedstat_enabled();
-		prof_on = SLEEP_PROFILING;
-		if (str[strlen(sleepstr)] == ',')
-			str += strlen(sleepstr) + 1;
-		if (get_option(&str, &par))
-			prof_shift = clamp(par, 0, BITS_PER_LONG - 1);
-		pr_info("kernel sleep profiling enabled (shift: %u)\n",
-			prof_shift);
-#else
-		pr_warn("kernel sleep profiling requires CONFIG_SCHEDSTATS\n");
-#endif /* CONFIG_SCHEDSTATS */
-	} else if (!strncmp(str, schedstr, strlen(schedstr))) {
+	if (!strncmp(str, schedstr, strlen(schedstr))) {
 		prof_on = SCHED_PROFILING;
 		if (str[strlen(schedstr)] == ',')
 			str += strlen(schedstr) + 1;
@@ -109,6 +95,13 @@
 
 	/* only text is profiled */
 	prof_len = (_etext - _stext) >> prof_shift;
+
+	if (!prof_len) {
+		pr_warn("profiling shift: %u too large\n", prof_shift);
+		prof_on = 0;
+		return -EINVAL;
+	}
+
 	buffer_bytes = prof_len*sizeof(atomic_t);
 
 	if (!alloc_cpumask_var(&prof_cpu_mask, GFP_KERNEL))
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/ptrace.c
@@ -371,6 +371,26 @@
 	return !err;
 }
 
+static int check_ptrace_options(unsigned long data)
+{
+	if (data & ~(unsigned long)PTRACE_O_MASK)
+		return -EINVAL;
+
+	if (unlikely(data & PTRACE_O_SUSPEND_SECCOMP)) {
+		if (!IS_ENABLED(CONFIG_CHECKPOINT_RESTORE) ||
+		    !IS_ENABLED(CONFIG_SECCOMP))
+			return -EINVAL;
+
+		if (!capable(CAP_SYS_ADMIN))
+			return -EPERM;
+
+		if (seccomp_mode(&current->seccomp) != SECCOMP_MODE_DISABLED ||
+		    current->ptrace & PT_SUSPEND_SECCOMP)
+			return -EPERM;
+	}
+	return 0;
+}
+
 static int ptrace_attach(struct task_struct *task, long request,
 			 unsigned long addr,
 			 unsigned long flags)
@@ -382,8 +402,16 @@
 	if (seize) {
 		if (addr != 0)
 			goto out;
+		/*
+		 * This duplicates the check in check_ptrace_options() because
+		 * ptrace_attach() and ptrace_setoptions() have historically
+		 * used different error codes for unknown ptrace options.
+		 */
 		if (flags & ~(unsigned long)PTRACE_O_MASK)
 			goto out;
+		retval = check_ptrace_options(flags);
+		if (retval)
+			return retval;
 		flags = PT_PTRACED | PT_SEIZED | (flags << PT_OPT_FLAG_SHIFT);
 	} else {
 		flags = PT_PTRACED;
@@ -656,22 +684,11 @@
 static int ptrace_setoptions(struct task_struct *child, unsigned long data)
 {
 	unsigned flags;
+	int ret;
 
-	if (data & ~(unsigned long)PTRACE_O_MASK)
-		return -EINVAL;
-
-	if (unlikely(data & PTRACE_O_SUSPEND_SECCOMP)) {
-		if (!IS_ENABLED(CONFIG_CHECKPOINT_RESTORE) ||
-		    !IS_ENABLED(CONFIG_SECCOMP))
-			return -EINVAL;
-
-		if (!capable(CAP_SYS_ADMIN))
-			return -EPERM;
-
-		if (seccomp_mode(&current->seccomp) != SECCOMP_MODE_DISABLED ||
-		    current->ptrace & PT_SUSPEND_SECCOMP)
-			return -EPERM;
-	}
+	ret = check_ptrace_options(data);
+	if (ret)
+		return ret;
 
 	/* Avoid intermediate state when all opts are cleared */
 	flags = child->ptrace;
@@ -1221,9 +1238,8 @@
 		return ptrace_resume(child, request, data);
 
 	case PTRACE_KILL:
-		if (child->exit_state)	/* already dead */
-			return 0;
-		return ptrace_resume(child, request, SIGKILL);
+		send_sig_info(SIGKILL, SEND_SIG_NOINFO, child);
+		return 0;
 
 #ifdef CONFIG_HAVE_ARCH_TRACEHOOK
 	case PTRACE_GETREGSET:
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/Kconfig
@@ -86,6 +86,7 @@
 
 config TASKS_RUDE_RCU
 	def_bool 0
+	select IRQ_WORK
 	help
 	  This option enables a task-based RCU implementation that uses
 	  only context switch (including preemption) and user-mode
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/rcu_segcblist.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/rcu_segcblist.h
@@ -56,13 +56,13 @@
 static inline void rcu_segcblist_set_flags(struct rcu_segcblist *rsclp,
 					   int flags)
 {
-	rsclp->flags |= flags;
+	WRITE_ONCE(rsclp->flags, rsclp->flags | flags);
 }
 
 static inline void rcu_segcblist_clear_flags(struct rcu_segcblist *rsclp,
 					     int flags)
 {
-	rsclp->flags &= ~flags;
+	WRITE_ONCE(rsclp->flags, rsclp->flags & ~flags);
 }
 
 static inline bool rcu_segcblist_test_flags(struct rcu_segcblist *rsclp,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/rcuscale.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/rcuscale.c
@@ -50,8 +50,8 @@
 	pr_alert("%s" SCALE_FLAG " %s\n", scale_type, s)
 #define VERBOSE_SCALEOUT_STRING(s) \
 	do { if (verbose) pr_alert("%s" SCALE_FLAG " %s\n", scale_type, s); } while (0)
-#define VERBOSE_SCALEOUT_ERRSTRING(s) \
-	do { if (verbose) pr_alert("%s" SCALE_FLAG "!!! %s\n", scale_type, s); } while (0)
+#define SCALEOUT_ERRSTRING(s) \
+	pr_alert("%s" SCALE_FLAG "!!! %s\n", scale_type, s)
 
 /*
  * The intended use cases for the nreaders and nwriters module parameters
@@ -402,7 +402,7 @@
 	sched_set_fifo_low(current);
 
 	if (holdoff)
-		schedule_timeout_uninterruptible(holdoff * HZ);
+		schedule_timeout_idle(holdoff * HZ);
 
 	/*
 	 * Wait until rcu_end_inkernel_boot() is called for normal GP tests
@@ -428,7 +428,7 @@
 			udelay(writer_holdoff);
 		wdp = &wdpp[i];
 		*wdp = ktime_get_mono_fast_ns();
-		if (gp_async) {
+		if (gp_async && !WARN_ON_ONCE(!cur_ops->async)) {
 retry:
 			if (!rhp)
 				rhp = kmalloc(sizeof(*rhp), GFP_KERNEL);
@@ -484,7 +484,7 @@
 			i++;
 		rcu_scale_wait_shutdown();
 	} while (!torture_must_stop());
-	if (gp_async) {
+	if (gp_async && cur_ops->async) {
 		cur_ops->gp_barrier();
 	}
 	writer_n_durations[me] = i_max + 1;
@@ -500,89 +500,6 @@
 		 scale_type, tag, nrealreaders, nrealwriters, verbose, shutdown);
 }
 
-static void
-rcu_scale_cleanup(void)
-{
-	int i;
-	int j;
-	int ngps = 0;
-	u64 *wdp;
-	u64 *wdpp;
-
-	/*
-	 * Would like warning at start, but everything is expedited
-	 * during the mid-boot phase, so have to wait till the end.
-	 */
-	if (rcu_gp_is_expedited() && !rcu_gp_is_normal() && !gp_exp)
-		VERBOSE_SCALEOUT_ERRSTRING("All grace periods expedited, no normal ones to measure!");
-	if (rcu_gp_is_normal() && gp_exp)
-		VERBOSE_SCALEOUT_ERRSTRING("All grace periods normal, no expedited ones to measure!");
-	if (gp_exp && gp_async)
-		VERBOSE_SCALEOUT_ERRSTRING("No expedited async GPs, so went with async!");
-
-	if (torture_cleanup_begin())
-		return;
-	if (!cur_ops) {
-		torture_cleanup_end();
-		return;
-	}
-
-	if (reader_tasks) {
-		for (i = 0; i < nrealreaders; i++)
-			torture_stop_kthread(rcu_scale_reader,
-					     reader_tasks[i]);
-		kfree(reader_tasks);
-	}
-
-	if (writer_tasks) {
-		for (i = 0; i < nrealwriters; i++) {
-			torture_stop_kthread(rcu_scale_writer,
-					     writer_tasks[i]);
-			if (!writer_n_durations)
-				continue;
-			j = writer_n_durations[i];
-			pr_alert("%s%s writer %d gps: %d\n",
-				 scale_type, SCALE_FLAG, i, j);
-			ngps += j;
-		}
-		pr_alert("%s%s start: %llu end: %llu duration: %llu gps: %d batches: %ld\n",
-			 scale_type, SCALE_FLAG,
-			 t_rcu_scale_writer_started, t_rcu_scale_writer_finished,
-			 t_rcu_scale_writer_finished -
-			 t_rcu_scale_writer_started,
-			 ngps,
-			 rcuscale_seq_diff(b_rcu_gp_test_finished,
-					   b_rcu_gp_test_started));
-		for (i = 0; i < nrealwriters; i++) {
-			if (!writer_durations)
-				break;
-			if (!writer_n_durations)
-				continue;
-			wdpp = writer_durations[i];
-			if (!wdpp)
-				continue;
-			for (j = 0; j < writer_n_durations[i]; j++) {
-				wdp = &wdpp[j];
-				pr_alert("%s%s %4d writer-duration: %5d %llu\n",
-					scale_type, SCALE_FLAG,
-					i, j, *wdp);
-				if (j % 100 == 0)
-					schedule_timeout_uninterruptible(1);
-			}
-			kfree(writer_durations[i]);
-		}
-		kfree(writer_tasks);
-		kfree(writer_durations);
-		kfree(writer_n_durations);
-	}
-
-	/* Do torture-type-specific cleanup operations.  */
-	if (cur_ops->cleanup != NULL)
-		cur_ops->cleanup();
-
-	torture_cleanup_end();
-}
-
 /*
  * Return the number if non-negative.  If -1, the number of CPUs.
  * If less than -1, that much less than the number of CPUs, but
@@ -603,21 +520,6 @@
 }
 
 /*
- * RCU scalability shutdown kthread.  Just waits to be awakened, then shuts
- * down system.
- */
-static int
-rcu_scale_shutdown(void *arg)
-{
-	wait_event(shutdown_wq,
-		   atomic_read(&n_rcu_scale_writer_finished) >= nrealwriters);
-	smp_mb(); /* Wake before output. */
-	rcu_scale_cleanup();
-	kernel_power_off();
-	return -EINVAL;
-}
-
-/*
  * kfree_rcu() scalability tests: Start a kfree_rcu() loop on all CPUs for number
  * of iterations and measure total time and number of GP for all iterations to complete.
  */
@@ -736,8 +638,8 @@
 static int
 kfree_scale_shutdown(void *arg)
 {
-	wait_event(shutdown_wq,
-		   atomic_read(&n_kfree_scale_thread_ended) >= kfree_nrealthreads);
+	wait_event_idle(shutdown_wq,
+			atomic_read(&n_kfree_scale_thread_ended) >= kfree_nrealthreads);
 
 	smp_mb(); /* Wake before output. */
 
@@ -791,6 +693,108 @@
 	return firsterr;
 }
 
+static void
+rcu_scale_cleanup(void)
+{
+	int i;
+	int j;
+	int ngps = 0;
+	u64 *wdp;
+	u64 *wdpp;
+
+	/*
+	 * Would like warning at start, but everything is expedited
+	 * during the mid-boot phase, so have to wait till the end.
+	 */
+	if (rcu_gp_is_expedited() && !rcu_gp_is_normal() && !gp_exp)
+		SCALEOUT_ERRSTRING("All grace periods expedited, no normal ones to measure!");
+	if (rcu_gp_is_normal() && gp_exp)
+		SCALEOUT_ERRSTRING("All grace periods normal, no expedited ones to measure!");
+	if (gp_exp && gp_async)
+		SCALEOUT_ERRSTRING("No expedited async GPs, so went with async!");
+
+	if (kfree_rcu_test) {
+		kfree_scale_cleanup();
+		return;
+	}
+
+	if (torture_cleanup_begin())
+		return;
+	if (!cur_ops) {
+		torture_cleanup_end();
+		return;
+	}
+
+	if (reader_tasks) {
+		for (i = 0; i < nrealreaders; i++)
+			torture_stop_kthread(rcu_scale_reader,
+					     reader_tasks[i]);
+		kfree(reader_tasks);
+	}
+
+	if (writer_tasks) {
+		for (i = 0; i < nrealwriters; i++) {
+			torture_stop_kthread(rcu_scale_writer,
+					     writer_tasks[i]);
+			if (!writer_n_durations)
+				continue;
+			j = writer_n_durations[i];
+			pr_alert("%s%s writer %d gps: %d\n",
+				 scale_type, SCALE_FLAG, i, j);
+			ngps += j;
+		}
+		pr_alert("%s%s start: %llu end: %llu duration: %llu gps: %d batches: %ld\n",
+			 scale_type, SCALE_FLAG,
+			 t_rcu_scale_writer_started, t_rcu_scale_writer_finished,
+			 t_rcu_scale_writer_finished -
+			 t_rcu_scale_writer_started,
+			 ngps,
+			 rcuscale_seq_diff(b_rcu_gp_test_finished,
+					   b_rcu_gp_test_started));
+		for (i = 0; i < nrealwriters; i++) {
+			if (!writer_durations)
+				break;
+			if (!writer_n_durations)
+				continue;
+			wdpp = writer_durations[i];
+			if (!wdpp)
+				continue;
+			for (j = 0; j < writer_n_durations[i]; j++) {
+				wdp = &wdpp[j];
+				pr_alert("%s%s %4d writer-duration: %5d %llu\n",
+					scale_type, SCALE_FLAG,
+					i, j, *wdp);
+				if (j % 100 == 0)
+					schedule_timeout_uninterruptible(1);
+			}
+			kfree(writer_durations[i]);
+		}
+		kfree(writer_tasks);
+		kfree(writer_durations);
+		kfree(writer_n_durations);
+	}
+
+	/* Do torture-type-specific cleanup operations.  */
+	if (cur_ops->cleanup != NULL)
+		cur_ops->cleanup();
+
+	torture_cleanup_end();
+}
+
+/*
+ * RCU scalability shutdown kthread.  Just waits to be awakened, then shuts
+ * down system.
+ */
+static int
+rcu_scale_shutdown(void *arg)
+{
+	wait_event_idle(shutdown_wq, atomic_read(&n_rcu_scale_writer_finished) >= nrealwriters);
+	smp_mb(); /* Wake before output. */
+	rcu_scale_cleanup();
+	kernel_power_off();
+	return -EINVAL;
+}
+
 static int __init
 rcu_scale_init(void)
 {
@@ -845,7 +849,7 @@
 	reader_tasks = kcalloc(nrealreaders, sizeof(reader_tasks[0]),
 			       GFP_KERNEL);
 	if (reader_tasks == NULL) {
-		VERBOSE_SCALEOUT_ERRSTRING("out of memory");
+		SCALEOUT_ERRSTRING("out of memory");
 		firsterr = -ENOMEM;
 		goto unwind;
 	}
@@ -865,7 +869,7 @@
 		kcalloc(nrealwriters, sizeof(*writer_n_durations),
 			GFP_KERNEL);
 	if (!writer_tasks || !writer_durations || !writer_n_durations) {
-		VERBOSE_SCALEOUT_ERRSTRING("out of memory");
+		SCALEOUT_ERRSTRING("out of memory");
 		firsterr = -ENOMEM;
 		goto unwind;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/rcutorture.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/rcutorture.c
@@ -46,6 +46,7 @@
 #include <linux/oom.h>
 #include <linux/tick.h>
 #include <linux/rcupdate_trace.h>
+#include <linux/nmi.h>
 
 #include "rcu.h"
 
@@ -109,6 +110,8 @@
 torture_param(int, stall_cpu, 0, "Stall duration (s), zero to disable.");
 torture_param(int, stall_cpu_holdoff, 10,
 	     "Time to wait before starting stall (s).");
+torture_param(bool, stall_no_softlockup, false,
+	     "Avoid softlockup warning during cpu stall.");
 torture_param(int, stall_cpu_irqsoff, 0, "Disable interrupts while stalling.");
 torture_param(int, stall_cpu_block, 0, "Sleep while stalling.");
 torture_param(int, stall_gp_kthread, 0,
@@ -1432,28 +1435,34 @@
 	/* First, put new protection in place to avoid critical-section gap. */
 	if (statesnew & RCUTORTURE_RDR_BH)
 		local_bh_disable();
+	if (statesnew & RCUTORTURE_RDR_RBH)
+		rcu_read_lock_bh();
 	if (statesnew & RCUTORTURE_RDR_IRQ)
 		local_irq_disable();
 	if (statesnew & RCUTORTURE_RDR_PREEMPT)
 		preempt_disable();
-	if (statesnew & RCUTORTURE_RDR_RBH)
-		rcu_read_lock_bh();
 	if (statesnew & RCUTORTURE_RDR_SCHED)
 		rcu_read_lock_sched();
 	if (statesnew & RCUTORTURE_RDR_RCU)
 		idxnew = cur_ops->readlock() << RCUTORTURE_RDR_SHIFT;
 
-	/* Next, remove old protection, irq first due to bh conflict. */
+	/*
+	 * Next, remove old protection, in decreasing order of strength
+	 * to avoid unlock paths that aren't safe in the stronger
+	 * context. Namely: BH can not be enabled with disabled interrupts.
+	 * Additionally PREEMPT_RT requires that BH is enabled in preemptible
+	 * context.
+	 */
 	if (statesold & RCUTORTURE_RDR_IRQ)
 		local_irq_enable();
-	if (statesold & RCUTORTURE_RDR_BH)
-		local_bh_enable();
 	if (statesold & RCUTORTURE_RDR_PREEMPT)
 		preempt_enable();
-	if (statesold & RCUTORTURE_RDR_RBH)
-		rcu_read_unlock_bh();
 	if (statesold & RCUTORTURE_RDR_SCHED)
 		rcu_read_unlock_sched();
+	if (statesold & RCUTORTURE_RDR_BH)
+		local_bh_enable();
+	if (statesold & RCUTORTURE_RDR_RBH)
+		rcu_read_unlock_bh();
 	if (statesold & RCUTORTURE_RDR_RCU) {
 		bool lockit = !statesnew && !(torture_random(trsp) & 0xffff);
 
@@ -1496,6 +1505,9 @@
 	int mask = rcutorture_extend_mask_max();
 	unsigned long randmask1 = torture_random(trsp) >> 8;
 	unsigned long randmask2 = randmask1 >> 3;
+	unsigned long preempts = RCUTORTURE_RDR_PREEMPT | RCUTORTURE_RDR_SCHED;
+	unsigned long preempts_irq = preempts | RCUTORTURE_RDR_IRQ;
+	unsigned long bhs = RCUTORTURE_RDR_BH | RCUTORTURE_RDR_RBH;
 
 	WARN_ON_ONCE(mask >> RCUTORTURE_RDR_SHIFT);
 	/* Mostly only one bit (need preemption!), sometimes lots of bits. */
@@ -1503,11 +1515,26 @@
 		mask = mask & randmask2;
 	else
 		mask = mask & (1 << (randmask2 % RCUTORTURE_RDR_NBITS));
-	/* Can't enable bh w/irq disabled. */
-	if ((mask & RCUTORTURE_RDR_IRQ) &&
-	    ((!(mask & RCUTORTURE_RDR_BH) && (oldmask & RCUTORTURE_RDR_BH)) ||
-	     (!(mask & RCUTORTURE_RDR_RBH) && (oldmask & RCUTORTURE_RDR_RBH))))
-		mask |= RCUTORTURE_RDR_BH | RCUTORTURE_RDR_RBH;
+
+	/*
+	 * Can't enable bh w/irq disabled.
+	 */
+	if (mask & RCUTORTURE_RDR_IRQ)
+		mask |= oldmask & bhs;
+
+	/*
+	 * Ideally these sequences would be detected in debug builds
+	 * (regardless of RT), but until then don't stop testing
+	 * them on non-RT.
+	 */
+	if (IS_ENABLED(CONFIG_PREEMPT_RT)) {
+		/* Can't modify BH in atomic context */
+		if (oldmask & preempts_irq)
+			mask &= ~bhs;
+		if ((oldmask | mask) & preempts_irq)
+			mask |= oldmask & bhs;
+	}
+
 	return mask ?: RCUTORTURE_RDR_RCU;
 }
 
@@ -1577,7 +1604,8 @@
 	preempt_disable();
 	pipe_count = READ_ONCE(p->rtort_pipe_count);
 	if (pipe_count > RCU_TORTURE_PIPE_LEN) {
-		/* Should not happen, but... */
+		// Should not happen in a correct RCU implementation,
+		// happens quite often for torture_type=busted.
 		pipe_count = RCU_TORTURE_PIPE_LEN;
 	}
 	completed = cur_ops->get_gp_seq();
@@ -1964,6 +1992,19 @@
 	if (boost_tasks[cpu] != NULL)
 		return 0;  /* Already created, nothing more to do. */
 
+	// Testing RCU priority boosting requires rcutorture do
+	// some serious abuse.  Counter this by running ksoftirqd
+	// at higher priority.
+	if (IS_BUILTIN(CONFIG_RCU_TORTURE_TEST)) {
+		struct sched_param sp;
+		struct task_struct *t;
+
+		t = per_cpu(ksoftirqd, cpu);
+		WARN_ON_ONCE(!t);
+		sp.sched_priority = 2;
+		sched_setscheduler_nocheck(t, SCHED_FIFO, &sp);
+	}
+
 	/* Don't allow time recalculation while creating a new task. */
 	mutex_lock(&boost_mutex);
 	rcu_torture_disable_rt_throttle();
@@ -2020,14 +2061,16 @@
 			preempt_disable();
 		pr_alert("%s start on CPU %d.\n",
 			  __func__, raw_smp_processor_id());
-		while (ULONG_CMP_LT((unsigned long)ktime_get_seconds(),
-				    stop_at))
+		while (ULONG_CMP_LT((unsigned long)ktime_get_seconds(), stop_at) &&
+		       !kthread_should_stop())
 			if (stall_cpu_block) {
 #ifdef CONFIG_PREEMPTION
 				preempt_schedule();
 #else
 				schedule_timeout_uninterruptible(HZ);
 #endif
+			} else if (stall_no_softlockup) {
+				touch_softlockup_watchdog();
 			}
 		if (stall_cpu_irqsoff)
 			local_irq_enable();
@@ -2143,7 +2186,7 @@
 	spin_lock_irqsave(&rfp->rcu_fwd_lock, flags);
 	rfcpp = rfp->rcu_fwd_cb_tail;
 	rfp->rcu_fwd_cb_tail = &rfcp->rfc_next;
-	WRITE_ONCE(*rfcpp, rfcp);
+	smp_store_release(rfcpp, rfcp);
 	WRITE_ONCE(rfp->n_launders_cb, rfp->n_launders_cb + 1);
 	i = ((jiffies - rfp->rcu_fwd_startat) / (HZ / FWD_CBS_HIST_DIV));
 	if (i >= ARRAY_SIZE(rfp->n_launders_hist))
@@ -2490,11 +2533,12 @@
 }
 
 /* IPI handler to get callback posted on desired CPU, if online. */
-static void rcu_torture_barrier1cb(void *rcu_void)
+static int rcu_torture_barrier1cb(void *rcu_void)
 {
 	struct rcu_head *rhp = rcu_void;
 
 	cur_ops->call(rhp, rcu_torture_barrier_cbf);
+	return 0;
 }
 
 /* kthread function to register callbacks used to test RCU barriers. */
@@ -2520,11 +2564,9 @@
 		 * The above smp_load_acquire() ensures barrier_phase load
 		 * is ordered before the following ->call().
 		 */
-		if (smp_call_function_single(myid, rcu_torture_barrier1cb,
-					     &rcu, 1)) {
-			// IPI failed, so use direct call from current CPU.
+		if (smp_call_on_cpu(myid, rcu_torture_barrier1cb, &rcu, 1))
 			cur_ops->call(&rcu, rcu_torture_barrier_cbf);
-		}
+
 		if (atomic_dec_and_test(&barrier_cbs_count))
 			wake_up(&barrier_wq);
 	} while (!torture_must_stop());
@@ -2819,7 +2861,7 @@
 		 rcutorture_seq_diff(gp_seq, start_gp_seq));
 	torture_stop_kthread(rcu_torture_stats, stats_task);
 	torture_stop_kthread(rcu_torture_fqs, fqs_task);
-	if (rcu_torture_can_boost())
+	if (rcu_torture_can_boost() && rcutor_hp >= 0)
 		cpuhp_remove_state(rcutor_hp);
 
 	/*
@@ -3037,7 +3079,7 @@
 	rcu_torture_write_types();
 	firsterr = torture_create_kthread(rcu_torture_writer, NULL,
 					  writer_task);
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	if (nfakewriters > 0) {
 		fakewriter_tasks = kcalloc(nfakewriters,
@@ -3052,7 +3094,7 @@
 	for (i = 0; i < nfakewriters; i++) {
 		firsterr = torture_create_kthread(rcu_torture_fakewriter,
 						  NULL, fakewriter_tasks[i]);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	reader_tasks = kcalloc(nrealreaders, sizeof(reader_tasks[0]),
@@ -3068,7 +3110,7 @@
 		rcu_torture_reader_mbchk[i].rtc_chkrdr = -1;
 		firsterr = torture_create_kthread(rcu_torture_reader, (void *)i,
 						  reader_tasks[i]);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	nrealnocbers = nocbs_nthreads;
@@ -3088,18 +3130,18 @@
 	}
 	for (i = 0; i < nrealnocbers; i++) {
 		firsterr = torture_create_kthread(rcu_nocb_toggle, NULL, nocb_tasks[i]);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	if (stat_interval > 0) {
 		firsterr = torture_create_kthread(rcu_torture_stats, NULL,
 						  stats_task);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	if (test_no_idle_hz && shuffle_interval > 0) {
 		firsterr = torture_shuffle_init(shuffle_interval * HZ);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	if (stutter < 0)
@@ -3109,7 +3151,7 @@
 
 		t = cur_ops->stall_dur ? cur_ops->stall_dur() : stutter * HZ;
 		firsterr = torture_stutter_init(stutter * HZ, t);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	if (fqs_duration < 0)
@@ -3118,7 +3160,7 @@
 		/* Create the fqs thread */
 		firsterr = torture_create_kthread(rcu_torture_fqs, NULL,
 						  fqs_task);
-		if (firsterr)
+		if (torture_init_error(firsterr))
 			goto unwind;
 	}
 	if (test_boost_interval < 1)
@@ -3132,44 +3174,29 @@
 		firsterr = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "RCU_TORTURE",
 					     rcutorture_booster_init,
 					     rcutorture_booster_cleanup);
-		if (firsterr < 0)
-			goto unwind;
 		rcutor_hp = firsterr;
-
-		// Testing RCU priority boosting requires rcutorture do
-		// some serious abuse.  Counter this by running ksoftirqd
-		// at higher priority.
-		if (IS_BUILTIN(CONFIG_RCU_TORTURE_TEST)) {
-			for_each_online_cpu(cpu) {
-				struct sched_param sp;
-				struct task_struct *t;
-
-				t = per_cpu(ksoftirqd, cpu);
-				WARN_ON_ONCE(!t);
-				sp.sched_priority = 2;
-				sched_setscheduler_nocheck(t, SCHED_FIFO, &sp);
-			}
-		}
+		if (torture_init_error(firsterr))
+			goto unwind;
 	}
 	shutdown_jiffies = jiffies + shutdown_secs * HZ;
 	firsterr = torture_shutdown_init(shutdown_secs, rcu_torture_cleanup);
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	firsterr = torture_onoff_init(onoff_holdoff * HZ, onoff_interval,
 				      rcutorture_sync);
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	firsterr = rcu_torture_stall_init();
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	firsterr = rcu_torture_fwd_prog_init();
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	firsterr = rcu_torture_barrier_init();
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	firsterr = rcu_torture_read_exit_init();
-	if (firsterr)
+	if (torture_init_error(firsterr))
 		goto unwind;
 	if (object_debug)
 		rcu_test_debug_objects();
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/refscale.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/refscale.c
@@ -777,7 +777,7 @@
 static int
 ref_scale_shutdown(void *arg)
 {
-	wait_event(shutdown_wq, shutdown_start);
+	wait_event_idle(shutdown_wq, shutdown_start);
 
 	smp_mb(); // Wake before output.
 	ref_scale_cleanup();
@@ -849,12 +849,11 @@
 	VERBOSE_SCALEOUT("Starting %d reader threads\n", nreaders);
 
 	for (i = 0; i < nreaders; i++) {
+		init_waitqueue_head(&reader_tasks[i].wq);
 		firsterr = torture_create_kthread(ref_scale_reader, (void *)i,
 						  reader_tasks[i].task);
 		if (firsterr)
 			goto unwind;
-
-		init_waitqueue_head(&(reader_tasks[i].wq));
 	}
 
 	// Main Task
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tasks.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tasks.h
@@ -171,8 +171,9 @@
 static void synchronize_rcu_tasks_generic(struct rcu_tasks *rtp)
 {
 	/* Complain if the scheduler has not started.  */
-	RCU_LOCKDEP_WARN(rcu_scheduler_active == RCU_SCHEDULER_INACTIVE,
-			 "synchronize_rcu_tasks called too soon");
+	if (WARN_ONCE(rcu_scheduler_active == RCU_SCHEDULER_INACTIVE,
+			 "synchronize_%s() called too soon", rtp->name))
+		return;
 
 	/* Wait for the grace period. */
 	wait_rcu_gp(rtp->call_func);
@@ -197,6 +198,7 @@
 	 * This loop is terminated by the system going down.  ;-)
 	 */
 	for (;;) {
+		set_tasks_gp_state(rtp, RTGS_WAIT_CBS);
 
 		/* Pick up any new callbacks. */
 		raw_spin_lock_irqsave(&rtp->cbs_lock, flags);
@@ -236,8 +238,6 @@
 		}
 		/* Paranoid sleep to keep this from entering a tight loop */
 		schedule_timeout_idle(rtp->gp_sleep);
-
-		set_tasks_gp_state(rtp, RTGS_WAIT_CBS);
 	}
 }
 
@@ -452,11 +452,21 @@
 static void rcu_tasks_postscan(struct list_head *hop)
 {
 	/*
-	 * Wait for tasks that are in the process of exiting.  This
-	 * does only part of the job, ensuring that all tasks that were
-	 * previously exiting reach the point where they have disabled
-	 * preemption, allowing the later synchronize_rcu() to finish
-	 * the job.
+	 * Exiting tasks may escape the tasklist scan. Those are vulnerable
+	 * until their final schedule() with TASK_DEAD state. To cope with
+	 * this, divide the fragile exit path part in two intersecting
+	 * read side critical sections:
+	 *
+	 * 1) An _SRCU_ read side starting before calling exit_notify(),
+	 *    which may remove the task from the tasklist, and ending after
+	 *    the final preempt_disable() call in do_exit().
+	 *
+	 * 2) An _RCU_ read side starting with the final preempt_disable()
+	 *    call in do_exit() and ending with the final call to schedule()
+	 *    with TASK_DEAD state.
+	 *
+	 * This handles the part 1). And postgp will handle part 2) with a
+	 * call to synchronize_rcu().
 	 */
 	synchronize_srcu(&tasks_rcu_exit_srcu);
 }
@@ -523,7 +533,10 @@
 	 *
 	 * In addition, this synchronize_rcu() waits for exiting tasks
 	 * to complete their final preempt_disable() region of execution,
-	 * cleaning up after the synchronize_srcu() above.
+	 * cleaning up after synchronize_srcu(&tasks_rcu_exit_srcu),
+	 * enforcing the whole region before tasklist removal until
+	 * the final schedule() with TASK_DEAD state to be an RCU TASKS
+	 * read side critical section.
 	 */
 	synchronize_rcu();
 }
@@ -613,27 +626,42 @@
 EXPORT_SYMBOL_GPL(show_rcu_tasks_classic_gp_kthread);
 #endif // !defined(CONFIG_TINY_RCU)
 
-/* Do the srcu_read_lock() for the above synchronize_srcu().  */
+/*
+ * Contribute to protect against tasklist scan blind spot while the
+ * task is exiting and may be removed from the tasklist. See
+ * corresponding synchronize_srcu() for further details.
+ */
 void exit_tasks_rcu_start(void) __acquires(&tasks_rcu_exit_srcu)
 {
-	preempt_disable();
 	current->rcu_tasks_idx = __srcu_read_lock(&tasks_rcu_exit_srcu);
-	preempt_enable();
 }
 
-/* Do the srcu_read_unlock() for the above synchronize_srcu().  */
-void exit_tasks_rcu_finish(void) __releases(&tasks_rcu_exit_srcu)
+/*
+ * Contribute to protect against tasklist scan blind spot while the
+ * task is exiting and may be removed from the tasklist. See
+ * corresponding synchronize_srcu() for further details.
+ */
+void exit_tasks_rcu_stop(void) __releases(&tasks_rcu_exit_srcu)
 {
 	struct task_struct *t = current;
 
-	preempt_disable();
 	__srcu_read_unlock(&tasks_rcu_exit_srcu, t->rcu_tasks_idx);
-	preempt_enable();
-	exit_tasks_rcu_finish_trace(t);
+}
+
+/*
+ * Contribute to protect against tasklist scan blind spot while the
+ * task is exiting and may be removed from the tasklist. See
+ * corresponding synchronize_srcu() for further details.
+ */
+void exit_tasks_rcu_finish(void)
+{
+	exit_tasks_rcu_stop();
+	exit_tasks_rcu_finish_trace(current);
 }
 
 #else /* #ifdef CONFIG_TASKS_RCU */
 void exit_tasks_rcu_start(void) { }
+void exit_tasks_rcu_stop(void) { }
 void exit_tasks_rcu_finish(void) { exit_tasks_rcu_finish_trace(current); }
 #endif /* #else #ifdef CONFIG_TASKS_RCU */
 
@@ -890,32 +918,24 @@
 
 	// If the task is no longer running on this CPU, leave.
 	if (unlikely(texp != t)) {
-		if (WARN_ON_ONCE(atomic_dec_and_test(&trc_n_readers_need_end)))
-			wake_up(&trc_wait);
 		goto reset_ipi; // Already on holdout list, so will check later.
 	}
 
 	// If the task is not in a read-side critical section, and
 	// if this is the last reader, awaken the grace-period kthread.
 	if (likely(!READ_ONCE(t->trc_reader_nesting))) {
-		if (WARN_ON_ONCE(atomic_dec_and_test(&trc_n_readers_need_end)))
-			wake_up(&trc_wait);
-		// Mark as checked after decrement to avoid false
-		// positives on the above WARN_ON_ONCE().
 		WRITE_ONCE(t->trc_reader_checked, true);
 		goto reset_ipi;
 	}
 	// If we are racing with an rcu_read_unlock_trace(), try again later.
-	if (unlikely(READ_ONCE(t->trc_reader_nesting) < 0)) {
-		if (WARN_ON_ONCE(atomic_dec_and_test(&trc_n_readers_need_end)))
-			wake_up(&trc_wait);
+	if (unlikely(READ_ONCE(t->trc_reader_nesting) < 0))
 		goto reset_ipi;
-	}
 	WRITE_ONCE(t->trc_reader_checked, true);
 
 	// Get here if the task is in a read-side critical section.  Set
 	// its state so that it will awaken the grace-period kthread upon
 	// exit from that critical section.
+	atomic_inc(&trc_n_readers_need_end); // One more to wait on.
 	WARN_ON_ONCE(READ_ONCE(t->trc_reader_special.b.need_qs));
 	WRITE_ONCE(t->trc_reader_special.b.need_qs, true);
 
@@ -928,10 +948,10 @@
 }
 
 /* Callback function for scheduler to check locked-down task.  */
-static bool trc_inspect_reader(struct task_struct *t, void *arg)
+static int trc_inspect_reader(struct task_struct *t, void *arg)
 {
 	int cpu = task_cpu(t);
-	bool in_qs = false;
+	int nesting;
 	bool ofl = cpu_is_offline(cpu);
 
 	if (task_curr(t)) {
@@ -939,7 +959,7 @@
 
 		// If no chance of heavyweight readers, do it the hard way.
 		if (!ofl && !IS_ENABLED(CONFIG_TASKS_TRACE_RCU_READ_MB))
-			return false;
+			return -EINVAL;
 
 		// If heavyweight readers are enabled on the remote task,
 		// we can inspect its state despite its currently running.
@@ -947,22 +967,22 @@
 		n_heavy_reader_attempts++;
 		if (!ofl && // Check for "running" idle tasks on offline CPUs.
 		    !rcu_dynticks_zero_in_eqs(cpu, &t->trc_reader_nesting))
-			return false; // No quiescent state, do it the hard way.
+			return -EINVAL; // No quiescent state, do it the hard way.
 		n_heavy_reader_updates++;
 		if (ofl)
 			n_heavy_reader_ofl_updates++;
-		in_qs = true;
+		nesting = 0;
 	} else {
 		// The task is not running, so C-language access is safe.
-		in_qs = likely(!t->trc_reader_nesting);
+		nesting = t->trc_reader_nesting;
 	}
 
-	// Mark as checked so that the grace-period kthread will
-	// remove it from the holdout list.
-	t->trc_reader_checked = true;
-
-	if (in_qs)
-		return true;  // Already in quiescent state, done!!!
+	// If not exiting a read-side critical section, mark as checked
+	// so that the grace-period kthread will remove it from the
+	// holdout list.
+	t->trc_reader_checked = nesting >= 0;
+	if (nesting <= 0)
+		return nesting ? -EINVAL : 0;  // If in QS, done, otherwise try again later.
 
 	// The task is in a read-side critical section, so set up its
 	// state so that it will awaken the grace-period kthread upon exit
@@ -970,7 +990,7 @@
 	atomic_inc(&trc_n_readers_need_end); // One more to wait on.
 	WARN_ON_ONCE(READ_ONCE(t->trc_reader_special.b.need_qs));
 	WRITE_ONCE(t->trc_reader_special.b.need_qs, true);
-	return true;
+	return 0;
 }
 
 /* Attempt to extract the state for the specified task. */
@@ -992,7 +1012,7 @@
 
 	// Attempt to nail down the task for inspection.
 	get_task_struct(t);
-	if (try_invoke_on_locked_down_task(t, trc_inspect_reader, NULL)) {
+	if (!task_call_func(t, trc_inspect_reader, NULL)) {
 		put_task_struct(t);
 		return;
 	}
@@ -1015,21 +1035,17 @@
 		if (per_cpu(trc_ipi_to_cpu, cpu) || t->trc_ipi_to_cpu >= 0)
 			return;
 
-		atomic_inc(&trc_n_readers_need_end);
 		per_cpu(trc_ipi_to_cpu, cpu) = true;
 		t->trc_ipi_to_cpu = cpu;
 		rcu_tasks_trace.n_ipis++;
-		if (smp_call_function_single(cpu,
-					     trc_read_check_handler, t, 0)) {
+		if (smp_call_function_single(cpu, trc_read_check_handler, t, 0)) {
 			// Just in case there is some other reason for
 			// failure than the target CPU being offline.
+			WARN_ONCE(1, "%s():  smp_call_function_single() failed for CPU: %d\n",
+				  __func__, cpu);
 			rcu_tasks_trace.n_ipis_fails++;
 			per_cpu(trc_ipi_to_cpu, cpu) = false;
-			t->trc_ipi_to_cpu = cpu;
-			if (atomic_dec_and_test(&trc_n_readers_need_end)) {
-				WARN_ON_ONCE(1);
-				wake_up(&trc_wait);
-			}
+			t->trc_ipi_to_cpu = -1;
 		}
 	}
 }
@@ -1074,7 +1090,7 @@
 {
 	int cpu;
 
-	for_each_possible_cpu(cpu)
+	for_each_online_cpu(cpu)
 		rcu_tasks_trace_pertask(idle_task(cpu), hop);
 
 	// Re-enable CPU hotplug now that the tasklist scan has completed.
@@ -1082,6 +1098,8 @@
 
 	// Wait for late-stage exiting tasks to finish exiting.
 	// These might have passed the call to exit_tasks_rcu_finish().
+
+	// If you remove the following line, update rcu_trace_implies_rcu_gp()!!!
 	synchronize_rcu();
 	// Any tasks that exit after this point will set ->trc_reader_checked.
 }
@@ -1150,14 +1168,28 @@
 	}
 }
 
+static void rcu_tasks_trace_empty_fn(void *unused)
+{
+}
+
 /* Wait for grace period to complete and provide ordering. */
 static void rcu_tasks_trace_postgp(struct rcu_tasks *rtp)
 {
+	int cpu;
 	bool firstreport;
 	struct task_struct *g, *t;
 	LIST_HEAD(holdouts);
 	long ret;
 
+	// Wait for any lingering IPI handlers to complete.  Note that
+	// if a CPU has gone offline or transitioned to userspace in the
+	// meantime, all IPI handlers should have been drained beforehand.
+	// Yes, this assumes that CPUs process IPIs in order.  If that ever
+	// changes, there will need to be a recheck and/or timed wait.
+	for_each_online_cpu(cpu)
+		if (smp_load_acquire(per_cpu_ptr(&trc_ipi_to_cpu, cpu)))
+			smp_call_function_single(cpu, rcu_tasks_trace_empty_fn, NULL, 1);
+
 	// Remove the safety count.
 	smp_mb__before_atomic();  // Order vs. earlier atomics
 	atomic_dec(&trc_n_readers_need_end);
@@ -1291,7 +1323,7 @@
 {
 	char buf[64];
 
-	sprintf(buf, "N%d h:%lu/%lu/%lu", atomic_read(&trc_n_readers_need_end),
+	snprintf(buf, sizeof(buf), "N%d h:%lu/%lu/%lu", atomic_read(&trc_n_readers_need_end),
 		data_race(n_heavy_reader_ofl_updates),
 		data_race(n_heavy_reader_updates),
 		data_race(n_heavy_reader_attempts));
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tree.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tree.c
@@ -31,6 +31,7 @@
 #include <linux/bitops.h>
 #include <linux/export.h>
 #include <linux/completion.h>
+#include <linux/kmemleak.h>
 #include <linux/moduleparam.h>
 #include <linux/panic.h>
 #include <linux/panic_notifier.h>
@@ -327,7 +328,7 @@
  */
 static __always_inline bool rcu_dynticks_curr_cpu_in_eqs(void)
 {
-	return !(atomic_read(this_cpu_ptr(&rcu_data.dynticks)) & 0x1);
+	return !(arch_atomic_read(this_cpu_ptr(&rcu_data.dynticks)) & 0x1);
 }
 
 /*
@@ -975,6 +976,7 @@
 	}
 	raw_spin_unlock_rcu_node(rdp->mynode);
 }
+NOKPROBE_SYMBOL(__rcu_irq_enter_check_tick);
 #endif /* CONFIG_NO_HZ_FULL */
 
 /**
@@ -1594,10 +1596,11 @@
 						  struct rcu_data *rdp)
 {
 	rcu_lockdep_assert_cblist_protected(rdp);
-	if (!rcu_seq_state(rcu_seq_current(&rnp->gp_seq)) ||
-	    !raw_spin_trylock_rcu_node(rnp))
+	if (!rcu_seq_state(rcu_seq_current(&rnp->gp_seq)) || !raw_spin_trylock_rcu_node(rnp))
 		return;
-	WARN_ON_ONCE(rcu_advance_cbs(rnp, rdp));
+	// The grace period cannot end while we hold the rcu_node lock.
+	if (rcu_seq_state(rcu_seq_current(&rnp->gp_seq)))
+		WARN_ON_ONCE(rcu_advance_cbs(rnp, rdp));
 	raw_spin_unlock_rcu_node(rnp);
 }
 
@@ -1904,10 +1907,22 @@
  */
 static void rcu_gp_fqs(bool first_time)
 {
+	int nr_fqs = READ_ONCE(rcu_state.nr_fqs_jiffies_stall);
 	struct rcu_node *rnp = rcu_get_root();
 
 	WRITE_ONCE(rcu_state.gp_activity, jiffies);
-	rcu_state.n_force_qs++;
+	WRITE_ONCE(rcu_state.n_force_qs, rcu_state.n_force_qs + 1);
+
+	WARN_ON_ONCE(nr_fqs > 3);
+	/* Only countdown nr_fqs for stall purposes if jiffies moves. */
+	if (nr_fqs) {
+		if (nr_fqs == 1) {
+			WRITE_ONCE(rcu_state.jiffies_stall,
+				   jiffies + rcu_jiffies_till_stall_check());
+		}
+		WRITE_ONCE(rcu_state.nr_fqs_jiffies_stall, --nr_fqs);
+	}
+
 	if (first_time) {
 		/* Collect dyntick-idle snapshots. */
 		force_qs_rnp(dyntick_save_progress_counter);
@@ -2475,7 +2490,7 @@
 	div = READ_ONCE(rcu_divisor);
 	div = div < 0 ? 7 : div > sizeof(long) * 8 - 2 ? sizeof(long) * 8 - 2 : div;
 	bl = max(rdp->blimit, pending >> div);
-	if (unlikely(bl > 100)) {
+	if (in_serving_softirq() && unlikely(bl > 100)) {
 		long rrn = READ_ONCE(rcu_resched_ns);
 
 		rrn = rrn < NSEC_PER_MSEC ? NSEC_PER_MSEC : rrn > NSEC_PER_SEC ? NSEC_PER_SEC : rrn;
@@ -2512,18 +2527,23 @@
 		/*
 		 * Stop only if limit reached and CPU has something to do.
 		 */
-		if (count >= bl && !offloaded &&
-		    (need_resched() ||
-		     (!is_idle_task(current) && !rcu_is_callbacks_kthread())))
-			break;
-		if (unlikely(tlimit)) {
-			/* only call local_clock() every 32 callbacks */
-			if (likely((count & 31) || local_clock() < tlimit))
-				continue;
-			/* Exceeded the time limit, so leave. */
-			break;
-		}
-		if (!in_serving_softirq()) {
+		if (in_serving_softirq()) {
+			if (count >= bl && (need_resched() ||
+					(!is_idle_task(current) && !rcu_is_callbacks_kthread())))
+				break;
+
+			/*
+			 * Make sure we don't spend too much time here and deprive other
+			 * softirq vectors of CPU cycles.
+			 */
+			if (unlikely(tlimit)) {
+				/* only call local_clock() every 32 callbacks */
+				if (likely((count & 31) || local_clock() < tlimit))
+					continue;
+				/* Exceeded the time limit, so leave. */
+				break;
+			}
+		} else {
 			local_bh_enable();
 			lockdep_assert_irqs_enabled();
 			cond_resched_tasks_rcu_qs();
@@ -2550,7 +2570,7 @@
 	/* Reset ->qlen_last_fqs_check trigger if enough CBs have drained. */
 	if (count == 0 && rdp->qlen_last_fqs_check != 0) {
 		rdp->qlen_last_fqs_check = 0;
-		rdp->n_force_qs_snap = rcu_state.n_force_qs;
+		rdp->n_force_qs_snap = READ_ONCE(rcu_state.n_force_qs);
 	} else if (count < rdp->qlen_last_fqs_check - qhimark)
 		rdp->qlen_last_fqs_check = count;
 
@@ -2668,7 +2688,7 @@
 	struct rcu_node *rnp_old = NULL;
 
 	/* Funnel through hierarchy to reduce memory contention. */
-	rnp = __this_cpu_read(rcu_data.mynode);
+	rnp = raw_cpu_read(rcu_data.mynode);
 	for (; rnp != NULL; rnp = rnp->parent) {
 		ret = (READ_ONCE(rcu_state.gp_flags) & RCU_GP_FLAG_FQS) ||
 		       !raw_spin_trylock(&rnp->fqslock);
@@ -2898,10 +2918,10 @@
 		} else {
 			/* Give the grace period a kick. */
 			rdp->blimit = DEFAULT_MAX_RCU_BLIMIT;
-			if (rcu_state.n_force_qs == rdp->n_force_qs_snap &&
+			if (READ_ONCE(rcu_state.n_force_qs) == rdp->n_force_qs_snap &&
 			    rcu_segcblist_first_pend_cb(&rdp->cblist) != head)
 				rcu_force_quiescent_state();
-			rdp->n_force_qs_snap = rcu_state.n_force_qs;
+			rdp->n_force_qs_snap = READ_ONCE(rcu_state.n_force_qs);
 			rdp->qlen_last_fqs_check = rcu_segcblist_n_cbs(&rdp->cblist);
 		}
 	}
@@ -3321,6 +3341,30 @@
 	}
 }
 
+static bool
+need_offload_krc(struct kfree_rcu_cpu *krcp)
+{
+	int i;
+
+	for (i = 0; i < FREE_N_CHANNELS; i++)
+		if (krcp->bkvhead[i])
+			return true;
+
+	return !!krcp->head;
+}
+
+static bool
+need_wait_for_krwp_work(struct kfree_rcu_cpu_work *krwp)
+{
+	int i;
+
+	for (i = 0; i < FREE_N_CHANNELS; i++)
+		if (krwp->bkvhead_free[i])
+			return true;
+
+	return !!krwp->head_free;
+}
+
 /*
  * This function is invoked after the KFREE_DRAIN_JIFFIES timeout.
  */
@@ -3337,14 +3381,13 @@
 	for (i = 0; i < KFREE_N_BATCHES; i++) {
 		struct kfree_rcu_cpu_work *krwp = &(krcp->krw_arr[i]);
 
-		// Try to detach bkvhead or head and attach it over any
-		// available corresponding free channel. It can be that
-		// a previous RCU batch is in progress, it means that
-		// immediately to queue another one is not possible so
-		// in that case the monitor work is rearmed.
-		if ((krcp->bkvhead[0] && !krwp->bkvhead_free[0]) ||
-			(krcp->bkvhead[1] && !krwp->bkvhead_free[1]) ||
-				(krcp->head && !krwp->head_free)) {
+		// Try to detach bulk_head or head and attach it, only when
+		// all channels are free.  Any channel is not free means at krwp
+		// there is on-going rcu work to handle krwp's free business.
+		if (need_wait_for_krwp_work(krwp))
+			continue;
+
+		if (need_offload_krc(krcp)) {
 			// Channel 1 corresponds to the SLAB-pointer bulk path.
 			// Channel 2 corresponds to vmalloc-pointer bulk path.
 			for (j = 0; j < FREE_N_CHANNELS; j++) {
@@ -3413,15 +3456,16 @@
 		bnode = (struct kvfree_rcu_bulk_data *)
 			__get_free_page(GFP_KERNEL | __GFP_NORETRY | __GFP_NOMEMALLOC | __GFP_NOWARN);
 
-		if (bnode) {
-			raw_spin_lock_irqsave(&krcp->lock, flags);
-			pushed = put_cached_bnode(krcp, bnode);
-			raw_spin_unlock_irqrestore(&krcp->lock, flags);
+		if (!bnode)
+			break;
 
-			if (!pushed) {
-				free_page((unsigned long) bnode);
-				break;
-			}
+		raw_spin_lock_irqsave(&krcp->lock, flags);
+		pushed = put_cached_bnode(krcp, bnode);
+		raw_spin_unlock_irqrestore(&krcp->lock, flags);
+
+		if (!pushed) {
+			free_page((unsigned long) bnode);
+			break;
 		}
 	}
 
@@ -3566,6 +3610,14 @@
 
 	WRITE_ONCE(krcp->count, krcp->count + 1);
 
+	/*
+	 * The kvfree_rcu() caller considers the pointer freed at this point
+	 * and likely removes any references to it. Since the actual slab
+	 * freeing (and kmemleak_free()) is deferred, tell kmemleak to ignore
+	 * this object (no scanning or false positives reporting).
+	 */
+	kmemleak_ignore(ptr);
+
 	// Set timer to drain after KFREE_DRAIN_JIFFIES.
 	if (rcu_scheduler_active == RCU_SCHEDULER_RUNNING &&
 	    !krcp->monitor_todo) {
@@ -4128,7 +4180,7 @@
 	/* Set up local state, ensuring consistent view of global state. */
 	raw_spin_lock_irqsave_rcu_node(rnp, flags);
 	rdp->qlen_last_fqs_check = 0;
-	rdp->n_force_qs_snap = rcu_state.n_force_qs;
+	rdp->n_force_qs_snap = READ_ONCE(rcu_state.n_force_qs);
 	rdp->blimit = blimit;
 	rdp->dynticks_nesting = 1;	/* CPU not up, no tearing. */
 	rcu_dynticks_eqs_online();
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tree.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tree.h
@@ -205,7 +205,6 @@
 	struct swait_queue_head nocb_state_wq; /* For offloading state changes */
 	struct task_struct *nocb_gp_kthread;
 	raw_spinlock_t nocb_lock;	/* Guard following pair of fields. */
-	atomic_t nocb_lock_contended;	/* Contention experienced. */
 	int nocb_defer_wakeup;		/* Defer wakeup of nocb_kthread. */
 	struct timer_list nocb_timer;	/* Enforce finite deferral. */
 	unsigned long nocb_gp_adv_time;	/* Last call_rcu() CB adv (jiffies). */
@@ -351,6 +350,10 @@
 						/*  in jiffies. */
 	unsigned long jiffies_stall;		/* Time at which to check */
 						/*  for CPU stalls. */
+	int nr_fqs_jiffies_stall;		/* Number of fqs loops after
+						 * which read jiffies and set
+						 * jiffies_stall. Stall
+						 * warnings disabled if !0. */
 	unsigned long jiffies_resched;		/* Time at which to resched */
 						/*  a reluctant CPU. */
 	unsigned long n_force_qs_gpstart;	/* Snapshot of n_force_qs at */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tree_exp.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tree_exp.h
@@ -387,6 +387,7 @@
 			continue;
 		}
 		if (get_cpu() == cpu) {
+			mask_ofl_test |= mask;
 			put_cpu();
 			continue;
 		}
@@ -506,7 +507,10 @@
 				if (rdp->rcu_forced_tick_exp)
 					continue;
 				rdp->rcu_forced_tick_exp = true;
-				tick_dep_set_cpu(cpu, TICK_DEP_BIT_RCU_EXP);
+				preempt_disable();
+				if (cpu_online(cpu))
+					tick_dep_set_cpu(cpu, TICK_DEP_BIT_RCU_EXP);
+				preempt_enable();
 			}
 		}
 		j = READ_ONCE(jiffies_till_first_fqs);
@@ -564,7 +568,9 @@
 				mask = leaf_node_cpu_bit(rnp, cpu);
 				if (!(READ_ONCE(rnp->expmask) & mask))
 					continue;
+				preempt_disable(); // For smp_processor_id() in dump_cpu_task().
 				dump_cpu_task(cpu);
+				preempt_enable();
 			}
 		}
 		jiffies_stall = 3 * rcu_jiffies_till_stall_check() + 3;
@@ -705,9 +711,11 @@
 	int ndetected = 0;
 	struct task_struct *t;
 
-	if (!READ_ONCE(rnp->exp_tasks))
-		return 0;
 	raw_spin_lock_irqsave_rcu_node(rnp, flags);
+	if (!rnp->exp_tasks) {
+		raw_spin_unlock_irqrestore_rcu_node(rnp, flags);
+		return 0;
+	}
 	t = list_entry(rnp->exp_tasks->prev,
 		       struct task_struct, rcu_node_entry);
 	list_for_each_entry_continue(t, &rnp->blkd_tasks, rcu_node_entry) {
@@ -760,7 +768,7 @@
 	my_cpu = get_cpu();
 	/* Quiescent state either not needed or already requested, leave. */
 	if (!(READ_ONCE(rnp->expmask) & rdp->grpmask) ||
-	    __this_cpu_read(rcu_data.cpu_no_qs.b.exp)) {
+	    rdp->cpu_no_qs.b.exp) {
 		put_cpu();
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tree_nocb.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tree_nocb.h
@@ -88,8 +88,7 @@
 
 /*
  * Acquire the specified rcu_data structure's ->nocb_bypass_lock.  If the
- * lock isn't immediately available, increment ->nocb_lock_contended to
- * flag the contention.
+ * lock isn't immediately available, perform minimal sanity check.
  */
 static void rcu_nocb_bypass_lock(struct rcu_data *rdp)
 	__acquires(&rdp->nocb_bypass_lock)
@@ -97,29 +96,12 @@
 	lockdep_assert_irqs_disabled();
 	if (raw_spin_trylock(&rdp->nocb_bypass_lock))
 		return;
-	atomic_inc(&rdp->nocb_lock_contended);
+	/*
+	 * Contention expected only when local enqueue collide with
+	 * remote flush from kthreads.
+	 */
 	WARN_ON_ONCE(smp_processor_id() != rdp->cpu);
-	smp_mb__after_atomic(); /* atomic_inc() before lock. */
 	raw_spin_lock(&rdp->nocb_bypass_lock);
-	smp_mb__before_atomic(); /* atomic_dec() after lock. */
-	atomic_dec(&rdp->nocb_lock_contended);
-}
-
-/*
- * Spinwait until the specified rcu_data structure's ->nocb_lock is
- * not contended.  Please note that this is extremely special-purpose,
- * relying on the fact that at most two kthreads and one CPU contend for
- * this lock, and also that the two kthreads are guaranteed to have frequent
- * grace-period-duration time intervals between successive acquisitions
- * of the lock.  This allows us to use an extremely simple throttling
- * mechanism, and further to apply it only to the CPU doing floods of
- * call_rcu() invocations.  Don't try this at home!
- */
-static void rcu_nocb_wait_contended(struct rcu_data *rdp)
-{
-	WARN_ON_ONCE(smp_processor_id() != rdp->cpu);
-	while (WARN_ON_ONCE(atomic_read(&rdp->nocb_lock_contended)))
-		cpu_relax();
 }
 
 /*
@@ -457,7 +439,6 @@
 	}
 
 	// We need to use the bypass.
-	rcu_nocb_wait_contended(rdp);
 	rcu_nocb_bypass_lock(rdp);
 	ncbs = rcu_cblist_n_cbs(&rdp->nocb_bypass);
 	rcu_segcblist_inc_len(&rdp->cblist); /* Must precede enqueue. */
@@ -1361,12 +1342,11 @@
 
 	sprintf(bufw, "%ld", rsclp->gp_seq[RCU_WAIT_TAIL]);
 	sprintf(bufr, "%ld", rsclp->gp_seq[RCU_NEXT_READY_TAIL]);
-	pr_info("   CB %d^%d->%d %c%c%c%c%c%c F%ld L%ld C%d %c%c%s%c%s%c%c q%ld %c CPU %d%s\n",
+	pr_info("   CB %d^%d->%d %c%c%c%c%c F%ld L%ld C%d %c%c%s%c%s%c%c q%ld %c CPU %d%s\n",
 		rdp->cpu, rdp->nocb_gp_rdp->cpu,
 		rdp->nocb_next_cb_rdp ? rdp->nocb_next_cb_rdp->cpu : -1,
 		"kK"[!!rdp->nocb_cb_kthread],
 		"bB"[raw_spin_is_locked(&rdp->nocb_bypass_lock)],
-		"cC"[!!atomic_read(&rdp->nocb_lock_contended)],
 		"lL"[raw_spin_is_locked(&rdp->nocb_lock)],
 		"sS"[!!rdp->nocb_cb_sleep],
 		".W"[swait_active(&rdp->nocb_cb_wq)],
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tree_plugin.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tree_plugin.h
@@ -458,7 +458,7 @@
  * be quite short, for example, in the case of the call from
  * rcu_read_unlock_special().
  */
-static void
+static notrace void
 rcu_preempt_deferred_qs_irqrestore(struct task_struct *t, unsigned long flags)
 {
 	bool empty_exp;
@@ -554,16 +554,16 @@
 			raw_spin_unlock_irqrestore_rcu_node(rnp, flags);
 		}
 
-		/* Unboost if we were boosted. */
-		if (IS_ENABLED(CONFIG_RCU_BOOST) && drop_boost_mutex)
-			rt_mutex_futex_unlock(&rnp->boost_mtx.rtmutex);
-
 		/*
 		 * If this was the last task on the expedited lists,
 		 * then we need to report up the rcu_node hierarchy.
 		 */
 		if (!empty_exp && empty_exp_now)
 			rcu_report_exp_rnp(rnp, true);
+
+		/* Unboost if we were boosted. */
+		if (IS_ENABLED(CONFIG_RCU_BOOST) && drop_boost_mutex)
+			rt_mutex_futex_unlock(&rnp->boost_mtx.rtmutex);
 	} else {
 		local_irq_restore(flags);
 	}
@@ -578,7 +578,7 @@
  * is disabled.  This function cannot be expected to understand these
  * nuances, so the caller must handle them.
  */
-static bool rcu_preempt_need_deferred_qs(struct task_struct *t)
+static notrace bool rcu_preempt_need_deferred_qs(struct task_struct *t)
 {
 	return (__this_cpu_read(rcu_data.exp_deferred_qs) ||
 		READ_ONCE(t->rcu_read_unlock_special.s)) &&
@@ -592,7 +592,7 @@
  * evaluate safety in terms of interrupt, softirq, and preemption
  * disabling.
  */
-static void rcu_preempt_deferred_qs(struct task_struct *t)
+static notrace void rcu_preempt_deferred_qs(struct task_struct *t)
 {
 	unsigned long flags;
 
@@ -638,7 +638,8 @@
 
 		expboost = (t->rcu_blocked_node && READ_ONCE(t->rcu_blocked_node->exp_tasks)) ||
 			   (rdp->grpmask & READ_ONCE(rnp->expmask)) ||
-			   IS_ENABLED(CONFIG_RCU_STRICT_GRACE_PERIOD) ||
+			   (IS_ENABLED(CONFIG_RCU_STRICT_GRACE_PERIOD) &&
+			   ((rdp->grpmask & READ_ONCE(rnp->qsmask)) || t->rcu_blocked_node)) ||
 			   (IS_ENABLED(CONFIG_RCU_BOOST) && irqs_were_disabled &&
 			    t->rcu_blocked_node);
 		// Need to defer quiescent state until everything is enabled.
@@ -922,7 +923,7 @@
  * Because there is no preemptible RCU, there can be no deferred quiescent
  * states.
  */
-static bool rcu_preempt_need_deferred_qs(struct task_struct *t)
+static notrace bool rcu_preempt_need_deferred_qs(struct task_struct *t)
 {
 	return false;
 }
@@ -1480,7 +1481,7 @@
 }
 
 /* Record the current task on dyntick-idle entry. */
-static void noinstr rcu_dynticks_task_enter(void)
+static __always_inline void rcu_dynticks_task_enter(void)
 {
 #if defined(CONFIG_TASKS_RCU) && defined(CONFIG_NO_HZ_FULL)
 	WRITE_ONCE(current->rcu_tasks_idle_cpu, smp_processor_id());
@@ -1488,7 +1489,7 @@
 }
 
 /* Record no current task on dyntick-idle exit. */
-static void noinstr rcu_dynticks_task_exit(void)
+static __always_inline void rcu_dynticks_task_exit(void)
 {
 #if defined(CONFIG_TASKS_RCU) && defined(CONFIG_NO_HZ_FULL)
 	WRITE_ONCE(current->rcu_tasks_idle_cpu, -1);
@@ -1496,7 +1497,7 @@
 }
 
 /* Turn on heavyweight RCU tasks trace readers on idle/user entry. */
-static void rcu_dynticks_task_trace_enter(void)
+static __always_inline void rcu_dynticks_task_trace_enter(void)
 {
 #ifdef CONFIG_TASKS_TRACE_RCU
 	if (IS_ENABLED(CONFIG_TASKS_TRACE_RCU_READ_MB))
@@ -1505,7 +1506,7 @@
 }
 
 /* Turn off heavyweight RCU tasks trace readers on idle/user exit. */
-static void rcu_dynticks_task_trace_exit(void)
+static __always_inline void rcu_dynticks_task_trace_exit(void)
 {
 #ifdef CONFIG_TASKS_TRACE_RCU
 	if (IS_ENABLED(CONFIG_TASKS_TRACE_RCU_READ_MB))
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rcu/tree_stall.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/rcu/tree_stall.h
@@ -121,12 +121,17 @@
 /**
  * rcu_cpu_stall_reset - restart stall-warning timeout for current grace period
  *
+ * To perform the reset request from the caller, disable stall detection until
+ * 3 fqs loops have passed. This is required to ensure a fresh jiffies is
+ * loaded.  It should be safe to do from the fqs loop as enough timer
+ * interrupts and context switches should have passed.
+ *
  * The caller must disable hard irqs.
  */
 void rcu_cpu_stall_reset(void)
 {
-	WRITE_ONCE(rcu_state.jiffies_stall,
-		   jiffies + rcu_jiffies_till_stall_check());
+	WRITE_ONCE(rcu_state.nr_fqs_jiffies_stall, 3);
+	WRITE_ONCE(rcu_state.jiffies_stall, ULONG_MAX);
 }
 
 //////////////////////////////////////////////////////////////////////////////
@@ -142,6 +147,7 @@
 	WRITE_ONCE(rcu_state.gp_start, j);
 	j1 = rcu_jiffies_till_stall_check();
 	smp_mb(); // ->gp_start before ->jiffies_stall and caller's ->gp_seq.
+	WRITE_ONCE(rcu_state.nr_fqs_jiffies_stall, 0);
 	WRITE_ONCE(rcu_state.jiffies_stall, j + j1);
 	rcu_state.jiffies_resched = j + j1 / 2;
 	rcu_state.n_force_qs_gpstart = READ_ONCE(rcu_state.n_force_qs);
@@ -240,16 +246,16 @@
  * Report out the state of a not-running task that is stalling the
  * current RCU grace period.
  */
-static bool check_slow_task(struct task_struct *t, void *arg)
+static int check_slow_task(struct task_struct *t, void *arg)
 {
 	struct rcu_stall_chk_rdr *rscrp = arg;
 
 	if (task_curr(t))
-		return false; // It is running, so decline to inspect it.
+		return -EBUSY; // It is running, so decline to inspect it.
 	rscrp->nesting = t->rcu_read_lock_nesting;
 	rscrp->rs = t->rcu_read_unlock_special;
 	rscrp->on_blkd_list = !list_empty(&t->rcu_node_entry);
-	return true;
+	return 0;
 }
 
 /*
@@ -283,7 +289,7 @@
 	raw_spin_unlock_irqrestore_rcu_node(rnp, flags);
 	while (i) {
 		t = ts[--i];
-		if (!try_invoke_on_locked_down_task(t, check_slow_task, &rscr))
+		if (task_call_func(t, check_slow_task, &rscr))
 			pr_cont(" P%d", t->pid);
 		else
 			pr_cont(" P%d/%d:%c%c%c%c",
@@ -662,6 +668,16 @@
 	    !rcu_gp_in_progress())
 		return;
 	rcu_stall_kick_kthreads();
+
+	/*
+	 * Check if it was requested (via rcu_cpu_stall_reset()) that the FQS
+	 * loop has to set jiffies to ensure a non-stale jiffies value. This
+	 * is required to have good jiffies value after coming out of long
+	 * breaks of jiffies updates. Not doing so can cause false positives.
+	 */
+	if (READ_ONCE(rcu_state.nr_fqs_jiffies_stall) > 0)
+		return;
+
 	j = jiffies;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/reboot.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/reboot.c
@@ -65,6 +65,7 @@
 void emergency_restart(void)
 {
 	kmsg_dump(KMSG_DUMP_EMERG);
+	system_state = SYSTEM_RESTART;
 	machine_emergency_restart();
 }
 EXPORT_SYMBOL_GPL(emergency_restart);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/relay.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/relay.c
@@ -151,13 +151,13 @@
 {
 	struct rchan_buf *buf;
 
-	if (chan->n_subbufs > KMALLOC_MAX_SIZE / sizeof(size_t *))
+	if (chan->n_subbufs > KMALLOC_MAX_SIZE / sizeof(size_t))
 		return NULL;
 
 	buf = kzalloc(sizeof(struct rchan_buf), GFP_KERNEL);
 	if (!buf)
 		return NULL;
-	buf->padding = kmalloc_array(chan->n_subbufs, sizeof(size_t *),
+	buf->padding = kmalloc_array(chan->n_subbufs, sizeof(size_t),
 				     GFP_KERNEL);
 	if (!buf->padding)
 		goto free_buf;
@@ -992,7 +992,8 @@
 	size_t subbuf_size = buf->chan->subbuf_size;
 	size_t n_subbufs = buf->chan->n_subbufs;
 	size_t consumed = buf->subbufs_consumed % n_subbufs;
-	size_t read_pos = consumed * subbuf_size + buf->bytes_consumed;
+	size_t read_pos = (consumed * subbuf_size + buf->bytes_consumed)
+			% (n_subbufs * subbuf_size);
 
 	read_subbuf = read_pos / subbuf_size;
 	padding = buf->padding[read_subbuf];
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/resource.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/resource.c
@@ -56,14 +56,6 @@
 
 static DEFINE_RWLOCK(resource_lock);
 
-/*
- * For memory hotplug, there is no way to free resource entries allocated
- * by boot mem after the system is up. So for reusing the resource entry
- * we need to remember the resource.
- */
-static struct resource *bootmem_resource_free;
-static DEFINE_SPINLOCK(bootmem_resource_lock);
-
 static struct resource *next_resource(struct resource *p)
 {
 	if (p->child)
@@ -148,36 +140,19 @@
 
 static void free_resource(struct resource *res)
 {
-	if (!res)
-		return;
-
-	if (!PageSlab(virt_to_head_page(res))) {
-		spin_lock(&bootmem_resource_lock);
-		res->sibling = bootmem_resource_free;
-		bootmem_resource_free = res;
-		spin_unlock(&bootmem_resource_lock);
-	} else {
+	/**
+	 * If the resource was allocated using memblock early during boot
+	 * we'll leak it here: we can only return full pages back to the
+	 * buddy and trying to be smart and reusing them eventually in
+	 * alloc_resource() overcomplicates resource handling.
+	 */
+	if (res && PageSlab(virt_to_head_page(res)))
 		kfree(res);
-	}
 }
 
 static struct resource *alloc_resource(gfp_t flags)
 {
-	struct resource *res = NULL;
-
-	spin_lock(&bootmem_resource_lock);
-	if (bootmem_resource_free) {
-		res = bootmem_resource_free;
-		bootmem_resource_free = res->sibling;
-	}
-	spin_unlock(&bootmem_resource_lock);
-
-	if (res)
-		memset(res, 0, sizeof(struct resource));
-	else
-		res = kzalloc(sizeof(struct resource), flags);
-
-	return res;
+	return kzalloc(sizeof(struct resource), flags);
 }
 
 /* Return the conflict entry if you can't request it */
@@ -505,20 +480,62 @@
 static int __region_intersects(resource_size_t start, size_t size,
 			unsigned long flags, unsigned long desc)
 {
-	struct resource res;
+	resource_size_t ostart, oend;
 	int type = 0; int other = 0;
-	struct resource *p;
+	struct resource *p, *dp;
+	bool is_type, covered;
+	struct resource res;
 
 	res.start = start;
 	res.end = start + size - 1;
 
 	for (p = iomem_resource.child; p ; p = p->sibling) {
-		bool is_type = (((p->flags & flags) == flags) &&
-				((desc == IORES_DESC_NONE) ||
-				 (desc == p->desc)));
-
-		if (resource_overlaps(p, &res))
-			is_type ? type++ : other++;
+		if (!resource_overlaps(p, &res))
+			continue;
+		is_type = (p->flags & flags) == flags &&
+			(desc == IORES_DESC_NONE || desc == p->desc);
+		if (is_type) {
+			type++;
+			continue;
+		}
+		/*
+		 * Continue to search in descendant resources as if the
+		 * matched descendant resources cover some ranges of 'p'.
+		 *
+		 * |------------- "CXL Window 0" ------------|
+		 * |-- "System RAM" --|
+		 *
+		 * will behave similar as the following fake resource
+		 * tree when searching "System RAM".
+		 *
+		 * |-- "System RAM" --||-- "CXL Window 0a" --|
+		 */
+		covered = false;
+		ostart = max(res.start, p->start);
+		oend = min(res.end, p->end);
+		for (dp = p->child; dp; dp = next_resource(dp)) {
+			if (!resource_overlaps(dp, &res))
+				continue;
+			is_type = (dp->flags & flags) == flags &&
+				(desc == IORES_DESC_NONE || desc == dp->desc);
+			if (is_type) {
+				type++;
+				/*
+				 * Range from 'ostart' to 'dp->start'
+				 * isn't covered by matched resource.
+				 */
+				if (dp->start > ostart)
+					break;
+				if (dp->end >= oend) {
+					covered = true;
+					break;
+				}
+				/* Remove covered range */
+				ostart = max(ostart, dp->end + 1);
+			}
+		}
+		if (!covered)
+			other++;
 	}
 
 	if (type == 0)
@@ -1350,20 +1367,6 @@
 			continue;
 		}
 
-		/*
-		 * All memory regions added from memory-hotplug path have the
-		 * flag IORESOURCE_SYSTEM_RAM. If the resource does not have
-		 * this flag, we know that we are dealing with a resource coming
-		 * from HMM/devm. HMM/devm use another mechanism to add/release
-		 * a resource. This goes via devm_request_mem_region and
-		 * devm_release_mem_region.
-		 * HMM/devm take care to release their resources when they want,
-		 * so if we are dealing with them, let us just back off here.
-		 */
-		if (!(res->flags & IORESOURCE_SYSRAM)) {
-			break;
-		}
-
 		if (!(res->flags & IORESOURCE_MEM))
 			break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/rseq.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/rseq.c
@@ -128,10 +128,10 @@
 	int ret;
 
 #ifdef CONFIG_64BIT
-	if (get_user(ptr, &t->rseq->rseq_cs.ptr64))
+	if (get_user(ptr, &t->rseq->rseq_cs))
 		return -EFAULT;
 #else
-	if (copy_from_user(&ptr, &t->rseq->rseq_cs.ptr64, sizeof(ptr)))
+	if (copy_from_user(&ptr, &t->rseq->rseq_cs, sizeof(ptr)))
 		return -EFAULT;
 #endif
 	if (!ptr) {
@@ -217,9 +217,9 @@
 	 * Set rseq_cs to NULL.
 	 */
 #ifdef CONFIG_64BIT
-	return put_user(0UL, &t->rseq->rseq_cs.ptr64);
+	return put_user(0UL, &t->rseq->rseq_cs);
 #else
-	if (clear_user(&t->rseq->rseq_cs.ptr64, sizeof(t->rseq->rseq_cs.ptr64)))
+	if (clear_user(&t->rseq->rseq_cs, sizeof(t->rseq->rseq_cs)))
 		return -EFAULT;
 	return 0;
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/scftorture.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/scftorture.c
@@ -175,7 +175,8 @@
 		scfs.n_all_wait += scf_stats_p[i].n_all_wait;
 	}
 	if (atomic_read(&n_errs) || atomic_read(&n_mb_in_errs) ||
-	    atomic_read(&n_mb_out_errs) || atomic_read(&n_alloc_errs))
+	    atomic_read(&n_mb_out_errs) ||
+	    (!IS_ENABLED(CONFIG_KASAN) && atomic_read(&n_alloc_errs)))
 		bangstr = "!!! ";
 	pr_alert("%s %sscf_invoked_count %s: %lld resched: %lld single: %lld/%lld single_ofl: %lld/%lld single_rpc: %lld single_rpc_ofl: %lld many: %lld/%lld all: %lld/%lld ",
 		 SCFTORT_FLAG, bangstr, isdone ? "VER" : "ver", invoked_count, scfs.n_resched,
@@ -271,9 +272,10 @@
 	}
 	this_cpu_inc(scf_invoked_count);
 	if (longwait <= 0) {
-		if (!(r & 0xffc0))
+		if (!(r & 0xffc0)) {
 			udelay(r & 0x3f);
-		goto out;
+			goto out;
+		}
 	}
 	if (r & 0xfff)
 		goto out;
@@ -326,7 +328,8 @@
 		preempt_disable();
 	if (scfsp->scfs_prim == SCF_PRIM_SINGLE || scfsp->scfs_wait) {
 		scfcp = kmalloc(sizeof(*scfcp), GFP_ATOMIC);
-		if (WARN_ON_ONCE(!scfcp)) {
+		if (!scfcp) {
+			WARN_ON_ONCE(!IS_ENABLED(CONFIG_KASAN));
 			atomic_inc(&n_alloc_errs);
 		} else {
 			scfcp->scfc_cpu = -1;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/autogroup.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/autogroup.c
@@ -31,7 +31,7 @@
 	ag->tg->rt_se = NULL;
 	ag->tg->rt_rq = NULL;
 #endif
-	sched_offline_group(ag->tg);
+	sched_release_group(ag->tg);
 	sched_destroy_group(ag->tg);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/core.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/core.c
@@ -21,7 +21,7 @@
 #include <asm/tlb.h>
 
 #include "../workqueue_internal.h"
-#include "../../fs/io-wq.h"
+#include "../../io_uring/io-wq.h"
 #include "../smpboot.h"
 
 #include "pelt.h"
@@ -36,6 +36,7 @@
 EXPORT_TRACEPOINT_SYMBOL_GPL(pelt_dl_tp);
 EXPORT_TRACEPOINT_SYMBOL_GPL(pelt_irq_tp);
 EXPORT_TRACEPOINT_SYMBOL_GPL(pelt_se_tp);
+EXPORT_TRACEPOINT_SYMBOL_GPL(pelt_thermal_tp);
 EXPORT_TRACEPOINT_SYMBOL_GPL(sched_cpu_capacity_tp);
 EXPORT_TRACEPOINT_SYMBOL_GPL(sched_overutilized_tp);
 EXPORT_TRACEPOINT_SYMBOL_GPL(sched_util_est_cfs_tp);
@@ -530,10 +531,10 @@
 		swap(rq1, rq2);
 
 	raw_spin_rq_lock(rq1);
-	if (__rq_lockp(rq1) == __rq_lockp(rq2))
-		return;
+	if (__rq_lockp(rq1) != __rq_lockp(rq2))
+		raw_spin_rq_lock_nested(rq2, SINGLE_DEPTH_NESTING);
 
-	raw_spin_rq_lock_nested(rq2, SINGLE_DEPTH_NESTING);
+	double_rq_clock_clear_update(rq1, rq2);
 }
 #endif
 
@@ -641,13 +642,15 @@
 #endif
 #ifdef CONFIG_PARAVIRT_TIME_ACCOUNTING
 	if (static_key_false((&paravirt_steal_rq_enabled))) {
-		steal = paravirt_steal_clock(cpu_of(rq));
+		u64 prev_steal;
+
+		steal = prev_steal = paravirt_steal_clock(cpu_of(rq));
 		steal -= rq->prev_steal_time_rq;
 
 		if (unlikely(steal > delta))
 			steal = delta;
 
-		rq->prev_steal_time_rq += steal;
+		rq->prev_steal_time_rq = prev_steal;
 		delta -= steal;
 	}
 #endif
@@ -938,9 +941,10 @@
 		struct task_struct *task;
 
 		task = container_of(node, struct task_struct, wake_q);
-		/* Task can safely be re-inserted now: */
 		node = node->next;
-		task->wake_q.next = NULL;
+		/* pairs with cmpxchg_relaxed() in __wake_q_add() */
+		WRITE_ONCE(task->wake_q.next, NULL);
+		/* Task can safely be re-inserted now. */
 
 		/*
 		 * wake_up_process() executes a full barrier, which pairs with
@@ -1105,9 +1109,9 @@
 	WARN_ON(!(flags & NOHZ_KICK_MASK));
 
 	rq->idle_balance = idle_cpu(cpu);
-	if (rq->idle_balance && !need_resched()) {
+	if (rq->idle_balance) {
 		rq->nohz_idle_balance = flags;
-		raise_softirq_irqoff(SCHED_SOFTIRQ);
+		__raise_softirq_irqoff(SCHED_SOFTIRQ);
 	}
 }
 
@@ -1202,27 +1206,24 @@
 static void set_load_weight(struct task_struct *p, bool update_load)
 {
 	int prio = p->static_prio - MAX_RT_PRIO;
-	struct load_weight *load = &p->se.load;
+	struct load_weight lw;
 
-	/*
-	 * SCHED_IDLE tasks get minimal weight:
-	 */
 	if (task_has_idle_policy(p)) {
-		load->weight = scale_load(WEIGHT_IDLEPRIO);
-		load->inv_weight = WMULT_IDLEPRIO;
-		return;
+		lw.weight = scale_load(WEIGHT_IDLEPRIO);
+		lw.inv_weight = WMULT_IDLEPRIO;
+	} else {
+		lw.weight = scale_load(sched_prio_to_weight[prio]);
+		lw.inv_weight = sched_prio_to_wmult[prio];
 	}
 
 	/*
 	 * SCHED_OTHER tasks have to update their load when changing their
 	 * weight
 	 */
-	if (update_load && p->sched_class == &fair_sched_class) {
-		reweight_task(p, prio);
-	} else {
-		load->weight = scale_load(sched_prio_to_weight[prio]);
-		load->inv_weight = sched_prio_to_wmult[prio];
-	}
+	if (update_load && p->sched_class == &fair_sched_class)
+		reweight_task(p, &lw);
+	else
+		p->se.load = lw;
 }
 
 #ifdef CONFIG_UCLAMP_TASK
@@ -1334,7 +1335,7 @@
 	if (!(rq->uclamp_flags & UCLAMP_FLAG_IDLE))
 		return;
 
-	WRITE_ONCE(rq->uclamp[clamp_id].value, clamp_value);
+	uclamp_rq_set(rq, clamp_id, clamp_value);
 }
 
 static inline
@@ -1512,8 +1513,8 @@
 	if (bucket->tasks == 1 || uc_se->value > bucket->value)
 		bucket->value = uc_se->value;
 
-	if (uc_se->value > READ_ONCE(uc_rq->value))
-		WRITE_ONCE(uc_rq->value, uc_se->value);
+	if (uc_se->value > uclamp_rq_get(rq, clamp_id))
+		uclamp_rq_set(rq, clamp_id, uc_se->value);
 }
 
 /*
@@ -1579,7 +1580,7 @@
 	if (likely(bucket->tasks))
 		return;
 
-	rq_clamp = READ_ONCE(uc_rq->value);
+	rq_clamp = uclamp_rq_get(rq, clamp_id);
 	/*
 	 * Defensive programming: this should never happen. If it happens,
 	 * e.g. due to future modification, warn and fixup the expected value.
@@ -1587,7 +1588,7 @@
 	SCHED_WARN_ON(bucket->value > rq_clamp);
 	if (bucket->value >= rq_clamp) {
 		bkt_clamp = uclamp_rq_max_value(rq, clamp_id, uc_se->value);
-		WRITE_ONCE(uc_rq->value, bkt_clamp);
+		uclamp_rq_set(rq, clamp_id, bkt_clamp);
 	}
 }
 
@@ -1914,7 +1915,7 @@
 		};
 	}
 
-	rq->uclamp_flags = 0;
+	rq->uclamp_flags = UCLAMP_FLAG_IDLE;
 }
 
 static void __init init_uclamp(void)
@@ -1969,7 +1970,7 @@
 
 	if (!(flags & ENQUEUE_RESTORE)) {
 		sched_info_enqueue(rq, p);
-		psi_enqueue(p, flags & ENQUEUE_WAKEUP);
+		psi_enqueue(p, (flags & ENQUEUE_WAKEUP) && !(flags & ENQUEUE_MIGRATED));
 	}
 
 	uclamp_rq_inc(rq, p);
@@ -1998,6 +1999,9 @@
 
 void activate_task(struct rq *rq, struct task_struct *p, int flags)
 {
+	if (task_on_rq_migrating(p))
+		flags |= ENQUEUE_MIGRATED;
+
 	enqueue_task(rq, p, flags);
 
 	p->on_rq = TASK_ON_RQ_QUEUED;
@@ -2373,9 +2377,11 @@
 		 * it.
 		 */
 		WARN_ON_ONCE(!pending->stop_pending);
+		preempt_disable();
 		task_rq_unlock(rq, p, &rf);
 		stop_one_cpu_nowait(task_cpu(p), migration_cpu_stop,
 				    &pending->arg, &pending->stop_work);
+		preempt_enable();
 		return 0;
 	}
 out:
@@ -2500,14 +2506,43 @@
 int dup_user_cpus_ptr(struct task_struct *dst, struct task_struct *src,
 		      int node)
 {
-	if (!src->user_cpus_ptr)
+	cpumask_t *user_mask;
+	unsigned long flags;
+
+	/*
+	 * Always clear dst->user_cpus_ptr first as their user_cpus_ptr's
+	 * may differ by now due to racing.
+	 */
+	dst->user_cpus_ptr = NULL;
+
+	/*
+	 * This check is racy and losing the race is a valid situation.
+	 * It is not worth the extra overhead of taking the pi_lock on
+	 * every fork/clone.
+	 */
+	if (data_race(!src->user_cpus_ptr))
 		return 0;
 
-	dst->user_cpus_ptr = kmalloc_node(cpumask_size(), GFP_KERNEL, node);
-	if (!dst->user_cpus_ptr)
+	user_mask = kmalloc_node(cpumask_size(), GFP_KERNEL, node);
+	if (!user_mask)
 		return -ENOMEM;
 
-	cpumask_copy(dst->user_cpus_ptr, src->user_cpus_ptr);
+	/*
+	 * Use pi_lock to protect content of user_cpus_ptr
+	 *
+	 * Though unlikely, user_cpus_ptr can be reset to NULL by a concurrent
+	 * do_set_cpus_allowed().
+	 */
+	raw_spin_lock_irqsave(&src->pi_lock, flags);
+	if (src->user_cpus_ptr) {
+		swap(dst->user_cpus_ptr, user_mask);
+		cpumask_copy(dst->user_cpus_ptr, src->user_cpus_ptr);
+	}
+	raw_spin_unlock_irqrestore(&src->pi_lock, flags);
+
+	if (unlikely(user_mask))
+		kfree(user_mask);
+
 	return 0;
 }
 
@@ -2627,12 +2662,13 @@
 			complete = true;
 		}
 
+		preempt_disable();
 		task_rq_unlock(rq, p, rf);
-
 		if (push_task) {
 			stop_one_cpu_nowait(rq->cpu, push_cpu_stop,
 					    p, &rq->push_work);
 		}
+		preempt_enable();
 
 		if (complete)
 			complete_all(&pending->done);
@@ -2698,12 +2734,13 @@
 		if (flags & SCA_MIGRATE_ENABLE)
 			p->migration_flags &= ~MDF_PUSH;
 
+		preempt_disable();
 		task_rq_unlock(rq, p, rf);
-
 		if (!stop_pending) {
 			stop_one_cpu_nowait(cpu_of(rq), migration_cpu_stop,
 					    &pending->arg, &pending->stop_work);
 		}
+		preempt_enable();
 
 		if (flags & SCA_MIGRATE_ENABLE)
 			return 0;
@@ -3489,11 +3526,11 @@
 #ifdef CONFIG_SMP
 	if (cpu == rq->cpu) {
 		__schedstat_inc(rq->ttwu_local);
-		__schedstat_inc(p->se.statistics.nr_wakeups_local);
+		__schedstat_inc(p->stats.nr_wakeups_local);
 	} else {
 		struct sched_domain *sd;
 
-		__schedstat_inc(p->se.statistics.nr_wakeups_remote);
+		__schedstat_inc(p->stats.nr_wakeups_remote);
 		rcu_read_lock();
 		for_each_domain(rq->cpu, sd) {
 			if (cpumask_test_cpu(cpu, sched_domain_span(sd))) {
@@ -3505,14 +3542,14 @@
 	}
 
 	if (wake_flags & WF_MIGRATED)
-		__schedstat_inc(p->se.statistics.nr_wakeups_migrate);
+		__schedstat_inc(p->stats.nr_wakeups_migrate);
 #endif /* CONFIG_SMP */
 
 	__schedstat_inc(rq->ttwu_count);
-	__schedstat_inc(p->se.statistics.nr_wakeups);
+	__schedstat_inc(p->stats.nr_wakeups);
 
 	if (wake_flags & WF_SYNC)
-		__schedstat_inc(p->se.statistics.nr_wakeups_sync);
+		__schedstat_inc(p->stats.nr_wakeups_sync);
 }
 
 /*
@@ -3691,15 +3728,11 @@
 	if (!is_idle_task(rcu_dereference(rq->curr)))
 		goto out;
 
-	if (set_nr_if_polling(rq->idle)) {
-		trace_sched_wake_idle_without_ipi(cpu);
-	} else {
-		rq_lock_irqsave(rq, &rf);
-		if (is_idle_task(rq->curr))
-			smp_send_reschedule(cpu);
-		/* Else CPU is not idle, do nothing here: */
-		rq_unlock_irqrestore(rq, &rf);
-	}
+	rq_lock_irqsave(rq, &rf);
+	if (is_idle_task(rq->curr))
+		resched_curr(rq);
+	/* Else CPU is not idle, do nothing here: */
+	rq_unlock_irqrestore(rq, &rf);
 
 out:
 	rcu_read_unlock();
@@ -3707,10 +3740,13 @@
 
 bool cpus_share_cache(int this_cpu, int that_cpu)
 {
+	if (this_cpu == that_cpu)
+		return true;
+
 	return per_cpu(sd_llc_id, this_cpu) == per_cpu(sd_llc_id, that_cpu);
 }
 
-static inline bool ttwu_queue_cond(int cpu, int wake_flags)
+static inline bool ttwu_queue_cond(struct task_struct *p, int cpu)
 {
 	/*
 	 * Do not complicate things with the async wake_list while the CPU is
@@ -3719,6 +3755,10 @@
 	if (!cpu_active(cpu))
 		return false;
 
+	/* Ensure the task will still be allowed to run on the CPU. */
+	if (!cpumask_test_cpu(cpu, p->cpus_ptr))
+		return false;
+
 	/*
 	 * If the CPU does not share cache, then queue the task on the
 	 * remote rqs wakelist to avoid accessing remote data.
@@ -3726,13 +3766,21 @@
 	if (!cpus_share_cache(smp_processor_id(), cpu))
 		return true;
 
+	if (cpu == smp_processor_id())
+		return false;
+
 	/*
-	 * If the task is descheduling and the only running task on the
-	 * CPU then use the wakelist to offload the task activation to
-	 * the soon-to-be-idle CPU as the current CPU is likely busy.
-	 * nr_running is checked to avoid unnecessary task stacking.
+	 * If the wakee cpu is idle, or the task is descheduling and the
+	 * only running task on the CPU, then use the wakelist to offload
+	 * the task activation to the idle (or soon-to-be-idle) CPU as
+	 * the current CPU is likely busy. nr_running is checked to
+	 * avoid unnecessary task stacking.
+	 *
+	 * Note that we can only get here with (wakee) p->on_rq=0,
+	 * p->on_cpu can be whatever, we've done the dequeue, so
+	 * the wakee has been accounted out of ->nr_running.
 	 */
-	if ((wake_flags & WF_ON_CPU) && cpu_rq(cpu)->nr_running <= 1)
+	if (!cpu_rq(cpu)->nr_running)
 		return true;
 
 	return false;
@@ -3740,10 +3788,7 @@
 
 static bool ttwu_queue_wakelist(struct task_struct *p, int cpu, int wake_flags)
 {
-	if (sched_feat(TTWU_QUEUE) && ttwu_queue_cond(cpu, wake_flags)) {
-		if (WARN_ON_ONCE(cpu == smp_processor_id()))
-			return false;
-
+	if (sched_feat(TTWU_QUEUE) && ttwu_queue_cond(p, cpu)) {
 		sched_clock_cpu(cpu); /* Sync clocks across CPUs */
 		__ttwu_queue_wakelist(p, cpu, wake_flags);
 		return true;
@@ -4065,7 +4110,7 @@
 	 * scheduling.
 	 */
 	if (smp_load_acquire(&p->on_cpu) &&
-	    ttwu_queue_wakelist(p, task_cpu(p), wake_flags | WF_ON_CPU))
+	    ttwu_queue_wakelist(p, task_cpu(p), wake_flags))
 		goto unlock;
 
 	/*
@@ -4106,46 +4151,61 @@
 }
 
 /**
- * try_invoke_on_locked_down_task - Invoke a function on task in fixed state
+ * task_call_func - Invoke a function on task in fixed state
  * @p: Process for which the function is to be invoked, can be @current.
  * @func: Function to invoke.
  * @arg: Argument to function.
  *
- * If the specified task can be quickly locked into a definite state
- * (either sleeping or on a given runqueue), arrange to keep it in that
- * state while invoking @func(@arg).  This function can use ->on_rq and
- * task_curr() to work out what the state is, if required.  Given that
- * @func can be invoked with a runqueue lock held, it had better be quite
- * lightweight.
+ * Fix the task in it's current state by avoiding wakeups and or rq operations
+ * and call @func(@arg) on it.  This function can use ->on_rq and task_curr()
+ * to work out what the state is, if required.  Given that @func can be invoked
+ * with a runqueue lock held, it had better be quite lightweight.
  *
  * Returns:
- *	@false if the task slipped out from under the locks.
- *	@true if the task was locked onto a runqueue or is sleeping.
- *		However, @func can override this by returning @false.
+ *   Whatever @func returns
  */
-bool try_invoke_on_locked_down_task(struct task_struct *p, bool (*func)(struct task_struct *t, void *arg), void *arg)
+int task_call_func(struct task_struct *p, task_call_f func, void *arg)
 {
+	struct rq *rq = NULL;
+	unsigned int state;
 	struct rq_flags rf;
-	bool ret = false;
-	struct rq *rq;
+	int ret;
 
 	raw_spin_lock_irqsave(&p->pi_lock, rf.flags);
-	if (p->on_rq) {
+
+	state = READ_ONCE(p->__state);
+
+	/*
+	 * Ensure we load p->on_rq after p->__state, otherwise it would be
+	 * possible to, falsely, observe p->on_rq == 0.
+	 *
+	 * See try_to_wake_up() for a longer comment.
+	 */
+	smp_rmb();
+
+	/*
+	 * Since pi->lock blocks try_to_wake_up(), we don't need rq->lock when
+	 * the task is blocked. Make sure to check @state since ttwu() can drop
+	 * locks at the end, see ttwu_queue_wakelist().
+	 */
+	if (state == TASK_RUNNING || state == TASK_WAKING || p->on_rq)
 		rq = __task_rq_lock(p, &rf);
-		if (task_rq(p) == rq)
-			ret = func(p, arg);
+
+	/*
+	 * At this point the task is pinned; either:
+	 *  - blocked and we're holding off wakeups	 (pi->lock)
+	 *  - woken, and we're holding off enqueue	 (rq->lock)
+	 *  - queued, and we're holding off schedule	 (rq->lock)
+	 *  - running, and we're holding off de-schedule (rq->lock)
+	 *
+	 * The called function (@func) can use: task_curr(), p->on_rq and
+	 * p->__state to differentiate between these states.
+	 */
+	ret = func(p, arg);
+
+	if (rq)
 		rq_unlock(rq, &rf);
-	} else {
-		switch (READ_ONCE(p->__state)) {
-		case TASK_RUNNING:
-		case TASK_WAKING:
-			break;
-		default:
-			smp_rmb(); // See smp_rmb() comment in try_to_wake_up().
-			if (!p->on_rq)
-				ret = func(p, arg);
-		}
-	}
+
 	raw_spin_unlock_irqrestore(&p->pi_lock, rf.flags);
 	return ret;
 }
@@ -4196,7 +4256,7 @@
 
 #ifdef CONFIG_SCHEDSTATS
 	/* Even if schedstat is disabled, there should not be garbage */
-	memset(&p->se.statistics, 0, sizeof(p->se.statistics));
+	memset(&p->stats, 0, sizeof(p->stats));
 #endif
 
 	RB_CLEAR_NODE(&p->dl.rb_node);
@@ -4328,8 +4388,6 @@
  */
 int sched_fork(unsigned long clone_flags, struct task_struct *p)
 {
-	unsigned long flags;
-
 	__sched_fork(clone_flags, p);
 	/*
 	 * We mark the process as NEW here. This guarantees that
@@ -4375,23 +4433,6 @@
 
 	init_entity_runnable_average(&p->se);
 
-	/*
-	 * The child is not yet in the pid-hash so no cgroup attach races,
-	 * and the cgroup is pinned to this child due to cgroup_fork()
-	 * is ran before sched_fork().
-	 *
-	 * Silence PROVE_RCU.
-	 */
-	raw_spin_lock_irqsave(&p->pi_lock, flags);
-	rseq_migrate(p);
-	/*
-	 * We're setting the CPU for the first time, we don't migrate,
-	 * so use __set_task_cpu().
-	 */
-	__set_task_cpu(p, smp_processor_id());
-	if (p->sched_class->task_fork)
-		p->sched_class->task_fork(p);
-	raw_spin_unlock_irqrestore(&p->pi_lock, flags);
 
 #ifdef CONFIG_SCHED_INFO
 	if (likely(sched_info_on()))
@@ -4408,6 +4449,35 @@
 	return 0;
 }
 
+void sched_cgroup_fork(struct task_struct *p, struct kernel_clone_args *kargs)
+{
+	unsigned long flags;
+
+	/*
+	 * Because we're not yet on the pid-hash, p->pi_lock isn't strictly
+	 * required yet, but lockdep gets upset if rules are violated.
+	 */
+	raw_spin_lock_irqsave(&p->pi_lock, flags);
+#ifdef CONFIG_CGROUP_SCHED
+	if (1) {
+		struct task_group *tg;
+		tg = container_of(kargs->cset->subsys[cpu_cgrp_id],
+				  struct task_group, css);
+		tg = autogroup_task_group(p, tg);
+		p->sched_task_group = tg;
+	}
+#endif
+	rseq_migrate(p);
+	/*
+	 * We're setting the CPU for the first time, we don't migrate,
+	 * so use __set_task_cpu().
+	 */
+	__set_task_cpu(p, smp_processor_id());
+	if (p->sched_class->task_fork)
+		p->sched_class->task_fork(p);
+	raw_spin_unlock_irqrestore(&p->pi_lock, flags);
+}
+
 void sched_post_fork(struct task_struct *p)
 {
 	uclamp_post_fork(p);
@@ -4571,7 +4641,8 @@
 	 * Claim the task as running, we do this before switching to it
 	 * such that any running task will have this set.
 	 *
-	 * See the ttwu() WF_ON_CPU case and its ordering comment.
+	 * See the smp_load_acquire(&p->on_cpu) case in ttwu() and
+	 * its ordering comment.
 	 */
 	WRITE_ONCE(next->on_cpu, 1);
 #endif
@@ -4616,25 +4687,55 @@
 
 static void balance_push(struct rq *rq);
 
+/*
+ * balance_push_callback is a right abuse of the callback interface and plays
+ * by significantly different rules.
+ *
+ * Where the normal balance_callback's purpose is to be ran in the same context
+ * that queued it (only later, when it's safe to drop rq->lock again),
+ * balance_push_callback is specifically targeted at __schedule().
+ *
+ * This abuse is tolerated because it places all the unlikely/odd cases behind
+ * a single test, namely: rq->balance_callback == NULL.
+ */
 struct callback_head balance_push_callback = {
 	.next = NULL,
 	.func = (void (*)(struct callback_head *))balance_push,
 };
 
-static inline struct callback_head *splice_balance_callbacks(struct rq *rq)
+static inline struct callback_head *
+__splice_balance_callbacks(struct rq *rq, bool split)
 {
 	struct callback_head *head = rq->balance_callback;
 
+	if (likely(!head))
+		return NULL;
+
 	lockdep_assert_rq_held(rq);
-	if (head)
+	/*
+	 * Must not take balance_push_callback off the list when
+	 * splice_balance_callbacks() and balance_callbacks() are not
+	 * in the same rq->lock section.
+	 *
+	 * In that case it would be possible for __schedule() to interleave
+	 * and observe the list empty.
+	 */
+	if (split && head == &balance_push_callback)
+		head = NULL;
+	else
 		rq->balance_callback = NULL;
 
 	return head;
 }
 
+static inline struct callback_head *splice_balance_callbacks(struct rq *rq)
+{
+	return __splice_balance_callbacks(rq, true);
+}
+
 static void __balance_callbacks(struct rq *rq)
 {
-	do_balance_callbacks(rq, splice_balance_callbacks(rq));
+	do_balance_callbacks(rq, __splice_balance_callbacks(rq, false));
 }
 
 static inline void balance_callbacks(struct rq *rq, struct callback_head *head)
@@ -5477,8 +5578,7 @@
 		pr_err("Preemption disabled at:");
 		print_ip_sym(KERN_ERR, preempt_disable_ip);
 	}
-	if (panic_on_warn)
-		panic("scheduling while atomic\n");
+	check_panic_on_warn("scheduling while atomic");
 
 	dump_stack();
 	add_taint(TAINT_WARN, LOCKDEP_STILL_OK);
@@ -5913,7 +6013,7 @@
 		if (p == src->core_pick || p == src->curr)
 			goto next;
 
-		if (!cpumask_test_cpu(this, &p->cpus_mask))
+		if (!is_cpu_allowed(p, this))
 			goto next;
 
 		if (p->core_occupation > dst->idle->core_occupation)
@@ -6335,8 +6435,12 @@
 		preempt_enable_no_resched();
 	}
 
-	if (tsk_is_pi_blocked(tsk))
-		return;
+	/*
+	 * spinlock and rwlock must not flush block requests.  This will
+	 * deadlock if the callback attempts to acquire a lock which is
+	 * already acquired.
+	 */
+	SCHED_WARN_ON(current->__state & TASK_RTLOCK_WAIT);
 
 	/*
 	 * If we are going to sleep and we have plugged IO queued,
@@ -6656,11 +6760,11 @@
 	int mode = sched_dynamic_mode(str);
 	if (mode < 0) {
 		pr_warn("Dynamic Preempt: unsupported mode: %s\n", str);
-		return 1;
+		return 0;
 	}
 
 	sched_dynamic_update(mode);
-	return 0;
+	return 1;
 }
 __setup("preempt=", setup_preempt_mode);
 
@@ -6931,6 +7035,7 @@
 	return (nice_rlim <= task_rlimit(p, RLIMIT_NICE) ||
 		capable(CAP_SYS_NICE));
 }
+EXPORT_SYMBOL(can_nice);
 
 #ifdef __ARCH_WANT_SYS_NICE
 
@@ -7220,6 +7325,7 @@
 	int reset_on_fork;
 	int queue_flags = DEQUEUE_SAVE | DEQUEUE_MOVE | DEQUEUE_NOCLOCK;
 	struct rq *rq;
+	bool cpuset_locked = false;
 
 	/* The pi code expects interrupts enabled */
 	BUG_ON(pi && in_interrupt());
@@ -7316,8 +7422,14 @@
 			return retval;
 	}
 
-	if (pi)
-		cpuset_read_lock();
+	/*
+	 * SCHED_DEADLINE bandwidth accounting relies on stable cpusets
+	 * information.
+	 */
+	if (dl_policy(policy) || dl_policy(p->policy)) {
+		cpuset_locked = true;
+		cpuset_lock();
+	}
 
 	/*
 	 * Make sure no PI-waiters arrive (or leave) while we are
@@ -7393,8 +7505,8 @@
 	if (unlikely(oldpolicy != -1 && oldpolicy != p->policy)) {
 		policy = oldpolicy = -1;
 		task_rq_unlock(rq, p, &rf);
-		if (pi)
-			cpuset_read_unlock();
+		if (cpuset_locked)
+			cpuset_unlock();
 		goto recheck;
 	}
 
@@ -7461,7 +7573,8 @@
 	task_rq_unlock(rq, p, &rf);
 
 	if (pi) {
-		cpuset_read_unlock();
+		if (cpuset_locked)
+			cpuset_unlock();
 		rt_mutex_adjust_pi(p);
 	}
 
@@ -7473,8 +7586,8 @@
 
 unlock:
 	task_rq_unlock(rq, p, &rf);
-	if (pi)
-		cpuset_read_unlock();
+	if (cpuset_locked)
+		cpuset_unlock();
 	return retval;
 }
 
@@ -8096,14 +8209,14 @@
 	if (len & (sizeof(unsigned long)-1))
 		return -EINVAL;
 
-	if (!alloc_cpumask_var(&mask, GFP_KERNEL))
+	if (!zalloc_cpumask_var(&mask, GFP_KERNEL))
 		return -ENOMEM;
 
 	ret = sched_getaffinity(pid, mask);
 	if (ret == 0) {
 		unsigned int retlen = min(len, cpumask_size());
 
-		if (copy_to_user(user_mask_ptr, mask, retlen))
+		if (copy_to_user(user_mask_ptr, cpumask_bits(mask), retlen))
 			ret = -EFAULT;
 		else
 			ret = retlen;
@@ -8147,7 +8260,7 @@
 #if !defined(CONFIG_PREEMPTION) || defined(CONFIG_PREEMPT_DYNAMIC)
 int __sched __cond_resched(void)
 {
-	if (should_resched(0)) {
+	if (should_resched(0) && !irqs_disabled()) {
 		preempt_schedule_common();
 		return 1;
 	}
@@ -8195,9 +8308,7 @@
 
 	if (spin_needbreak(lock) || resched) {
 		spin_unlock(lock);
-		if (resched)
-			preempt_schedule_common();
-		else
+		if (!_cond_resched())
 			cpu_relax();
 		ret = 1;
 		spin_lock(lock);
@@ -8215,9 +8326,7 @@
 
 	if (rwlock_needbreak(lock) || resched) {
 		read_unlock(lock);
-		if (resched)
-			preempt_schedule_common();
-		else
+		if (!_cond_resched())
 			cpu_relax();
 		ret = 1;
 		read_lock(lock);
@@ -8235,9 +8344,7 @@
 
 	if (rwlock_needbreak(lock) || resched) {
 		write_unlock(lock);
-		if (resched)
-			preempt_schedule_common();
-		else
+		if (!_cond_resched())
 			cpu_relax();
 		ret = 1;
 		write_lock(lock);
@@ -8637,9 +8744,6 @@
 	idle->flags |= PF_IDLE | PF_KTHREAD | PF_NO_SETAFFINITY;
 	kthread_set_per_cpu(idle, cpu);
 
-	scs_task_reset(idle);
-	kasan_unpoison_task_stack(idle);
-
 #ifdef CONFIG_SMP
 	/*
 	 * It's possible that init_idle() gets called multiple times on a task,
@@ -8701,8 +8805,7 @@
 	return ret;
 }
 
-int task_can_attach(struct task_struct *p,
-		    const struct cpumask *cs_cpus_allowed)
+int task_can_attach(struct task_struct *p)
 {
 	int ret = 0;
 
@@ -8715,16 +8818,9 @@
 	 * success of set_cpus_allowed_ptr() on all attached tasks
 	 * before cpus_mask may be changed.
 	 */
-	if (p->flags & PF_NO_SETAFFINITY) {
+	if (p->flags & PF_NO_SETAFFINITY)
 		ret = -EINVAL;
-		goto out;
-	}
 
-	if (dl_task(p) && !cpumask_intersects(task_rq(p)->rd->span,
-					      cs_cpus_allowed))
-		ret = dl_task_can_attach(p, cs_cpus_allowed);
-
-out:
 	return ret;
 }
 
@@ -8795,7 +8891,6 @@
 		finish_arch_post_lock_switch();
 	}
 
-	scs_task_reset(current);
 	/* finish_cpu(), as ran on the BP, will clean up the active_mm state */
 }
 
@@ -8882,9 +8977,11 @@
 	 * Temporarily drop rq->lock such that we can wake-up the stop task.
 	 * Both preemption and IRQs are still disabled.
 	 */
+	preempt_disable();
 	raw_spin_rq_unlock(rq);
 	stop_one_cpu_nowait(rq->cpu, __balance_push_cpu_stop, push_task,
 			    this_cpu_ptr(&push_work));
+	preempt_enable();
 	/*
 	 * At this point need_resched() is true and we'll take the loop in
 	 * schedule(). The next pick is obviously going to be the stop task
@@ -9007,8 +9104,10 @@
 static int cpuset_cpu_inactive(unsigned int cpu)
 {
 	if (!cpuhp_tasks_frozen) {
-		if (dl_cpu_busy(cpu))
-			return -EBUSY;
+		int ret = dl_bw_check_overflow(cpu);
+
+		if (ret)
+			return ret;
 		cpuset_update_active_cpus();
 	} else {
 		num_cpus_frozen++;
@@ -9017,6 +9116,22 @@
 	return 0;
 }
 
+static inline void sched_smt_present_inc(int cpu)
+{
+#ifdef CONFIG_SCHED_SMT
+	if (cpumask_weight(cpu_smt_mask(cpu)) == 2)
+		static_branch_inc_cpuslocked(&sched_smt_present);
+#endif
+}
+
+static inline void sched_smt_present_dec(int cpu)
+{
+#ifdef CONFIG_SCHED_SMT
+	if (cpumask_weight(cpu_smt_mask(cpu)) == 2)
+		static_branch_dec_cpuslocked(&sched_smt_present);
+#endif
+}
+
 int sched_cpu_activate(unsigned int cpu)
 {
 	struct rq *rq = cpu_rq(cpu);
@@ -9028,13 +9143,10 @@
 	 */
 	balance_push_set(cpu, false);
 
-#ifdef CONFIG_SCHED_SMT
 	/*
 	 * When going up, increment the number of cores with SMT present.
 	 */
-	if (cpumask_weight(cpu_smt_mask(cpu)) == 2)
-		static_branch_inc_cpuslocked(&sched_smt_present);
-#endif
+	sched_smt_present_inc(cpu);
 	set_cpu_active(cpu, true);
 
 	if (sched_smp_initialized) {
@@ -9103,13 +9215,12 @@
 	}
 	rq_unlock_irqrestore(rq, &rf);
 
-#ifdef CONFIG_SCHED_SMT
 	/*
 	 * When going down, decrement the number of cores with SMT present.
 	 */
-	if (cpumask_weight(cpu_smt_mask(cpu)) == 2)
-		static_branch_dec_cpuslocked(&sched_smt_present);
+	sched_smt_present_dec(cpu);
 
+#ifdef CONFIG_SCHED_SMT
 	sched_core_cpu_deactivate(cpu);
 #endif
 
@@ -9118,6 +9229,7 @@
 
 	ret = cpuset_cpu_inactive(cpu);
 	if (ret) {
+		sched_smt_present_inc(cpu);
 		balance_push_set(cpu, false);
 		set_cpu_active(cpu, true);
 		return ret;
@@ -9620,9 +9732,9 @@
 			continue;
 
 		p->se.exec_start = 0;
-		schedstat_set(p->se.statistics.wait_start,  0);
-		schedstat_set(p->se.statistics.sleep_start, 0);
-		schedstat_set(p->se.statistics.block_start, 0);
+		schedstat_set(p->stats.wait_start,  0);
+		schedstat_set(p->stats.sleep_start, 0);
+		schedstat_set(p->stats.block_start, 0);
 
 		if (!dl_task(p) && !rt_task(p)) {
 			/*
@@ -9716,6 +9828,22 @@
 	kmem_cache_free(task_group_cache, tg);
 }
 
+static void sched_free_group_rcu(struct rcu_head *rcu)
+{
+	sched_free_group(container_of(rcu, struct task_group, rcu));
+}
+
+static void sched_unregister_group(struct task_group *tg)
+{
+	unregister_fair_sched_group(tg);
+	unregister_rt_sched_group(tg);
+	/*
+	 * We have to wait for yet another RCU grace period to expire, as
+	 * print_cfs_stats() might run concurrently.
+	 */
+	call_rcu(&tg->rcu, sched_free_group_rcu);
+}
+
 /* allocate runqueue etc for a new task group */
 struct task_group *sched_create_group(struct task_group *parent)
 {
@@ -9759,25 +9887,35 @@
 }
 
 /* rcu callback to free various structures associated with a task group */
-static void sched_free_group_rcu(struct rcu_head *rhp)
+static void sched_unregister_group_rcu(struct rcu_head *rhp)
 {
 	/* Now it should be safe to free those cfs_rqs: */
-	sched_free_group(container_of(rhp, struct task_group, rcu));
+	sched_unregister_group(container_of(rhp, struct task_group, rcu));
 }
 
 void sched_destroy_group(struct task_group *tg)
 {
 	/* Wait for possible concurrent references to cfs_rqs complete: */
-	call_rcu(&tg->rcu, sched_free_group_rcu);
+	call_rcu(&tg->rcu, sched_unregister_group_rcu);
 }
 
-void sched_offline_group(struct task_group *tg)
+void sched_release_group(struct task_group *tg)
 {
 	unsigned long flags;
 
-	/* End participation in shares distribution: */
-	unregister_fair_sched_group(tg);
-
+	/*
+	 * Unlink first, to avoid walk_tg_tree_from() from finding us (via
+	 * sched_cfs_period_timer()).
+	 *
+	 * For this to be effective, we have to wait for all pending users of
+	 * this task group to leave their RCU critical section to ensure no new
+	 * user will see our dying task group any more. Specifically ensure
+	 * that tg_unthrottle_up() won't add decayed cfs_rq's to it.
+	 *
+	 * We therefore defer calling unregister_fair_sched_group() to
+	 * sched_unregister_group() which is guarantied to get called only after the
+	 * current RCU grace period has expired.
+	 */
 	spin_lock_irqsave(&task_group_lock, flags);
 	list_del_rcu(&tg->list);
 	list_del_rcu(&tg->siblings);
@@ -9896,7 +10034,7 @@
 {
 	struct task_group *tg = css_tg(css);
 
-	sched_offline_group(tg);
+	sched_release_group(tg);
 }
 
 static void cpu_cgroup_css_free(struct cgroup_subsys_state *css)
@@ -9906,7 +10044,7 @@
 	/*
 	 * Relies on the RCU grace period between css_released() and this.
 	 */
-	sched_free_group(tg);
+	sched_unregister_group(tg);
 }
 
 /*
@@ -10464,11 +10602,14 @@
 	seq_printf(sf, "throttled_time %llu\n", cfs_b->throttled_time);
 
 	if (schedstat_enabled() && tg != &root_task_group) {
+		struct sched_statistics *stats;
 		u64 ws = 0;
 		int i;
 
-		for_each_possible_cpu(i)
-			ws += schedstat_val(tg->se[i]->statistics.wait_sum);
+		for_each_possible_cpu(i) {
+			stats = __schedstats_from_se(tg->se[i]);
+			ws += schedstat_val(stats->wait_sum);
+		}
 
 		seq_printf(sf, "wait_sum %llu\n", ws);
 	}
@@ -10712,7 +10853,7 @@
 {
 	struct task_group *tg = css_tg(of_css(of));
 	u64 period = tg_get_cfs_period(tg);
-	u64 burst = tg_get_cfs_burst(tg);
+	u64 burst = tg->cfs_bandwidth.burst;
 	u64 quota;
 	int ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/cpuacct.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/cpuacct.c
@@ -21,15 +21,11 @@
 	[CPUACCT_STAT_SYSTEM] = "system",
 };
 
-struct cpuacct_usage {
-	u64	usages[CPUACCT_STAT_NSTATS];
-};
-
 /* track CPU usage of a group of tasks and its child groups */
 struct cpuacct {
 	struct cgroup_subsys_state	css;
 	/* cpuusage holds pointer to a u64-type object on every CPU */
-	struct cpuacct_usage __percpu	*cpuusage;
+	u64 __percpu	*cpuusage;
 	struct kernel_cpustat __percpu	*cpustat;
 };
 
@@ -49,7 +45,7 @@
 	return css_ca(ca->css.parent);
 }
 
-static DEFINE_PER_CPU(struct cpuacct_usage, root_cpuacct_cpuusage);
+static DEFINE_PER_CPU(u64, root_cpuacct_cpuusage);
 static struct cpuacct root_cpuacct = {
 	.cpustat	= &kernel_cpustat,
 	.cpuusage	= &root_cpuacct_cpuusage,
@@ -68,7 +64,7 @@
 	if (!ca)
 		goto out;
 
-	ca->cpuusage = alloc_percpu(struct cpuacct_usage);
+	ca->cpuusage = alloc_percpu(u64);
 	if (!ca->cpuusage)
 		goto out_free_ca;
 
@@ -99,7 +95,8 @@
 static u64 cpuacct_cpuusage_read(struct cpuacct *ca, int cpu,
 				 enum cpuacct_stat_index index)
 {
-	struct cpuacct_usage *cpuusage = per_cpu_ptr(ca->cpuusage, cpu);
+	u64 *cpuusage = per_cpu_ptr(ca->cpuusage, cpu);
+	u64 *cpustat = per_cpu_ptr(ca->cpustat, cpu)->cpustat;
 	u64 data;
 
 	/*
@@ -115,14 +112,17 @@
 	raw_spin_rq_lock_irq(cpu_rq(cpu));
 #endif
 
-	if (index == CPUACCT_STAT_NSTATS) {
-		int i = 0;
-
-		data = 0;
-		for (i = 0; i < CPUACCT_STAT_NSTATS; i++)
-			data += cpuusage->usages[i];
-	} else {
-		data = cpuusage->usages[index];
+	switch (index) {
+	case CPUACCT_STAT_USER:
+		data = cpustat[CPUTIME_USER] + cpustat[CPUTIME_NICE];
+		break;
+	case CPUACCT_STAT_SYSTEM:
+		data = cpustat[CPUTIME_SYSTEM] + cpustat[CPUTIME_IRQ] +
+			cpustat[CPUTIME_SOFTIRQ];
+		break;
+	case CPUACCT_STAT_NSTATS:
+		data = *cpuusage;
+		break;
 	}
 
 #ifndef CONFIG_64BIT
@@ -132,10 +132,14 @@
 	return data;
 }
 
-static void cpuacct_cpuusage_write(struct cpuacct *ca, int cpu, u64 val)
+static void cpuacct_cpuusage_write(struct cpuacct *ca, int cpu)
 {
-	struct cpuacct_usage *cpuusage = per_cpu_ptr(ca->cpuusage, cpu);
-	int i;
+	u64 *cpuusage = per_cpu_ptr(ca->cpuusage, cpu);
+	u64 *cpustat = per_cpu_ptr(ca->cpustat, cpu)->cpustat;
+
+	/* Don't allow to reset global kernel_cpustat */
+	if (ca == &root_cpuacct)
+		return;
 
 #ifndef CONFIG_64BIT
 	/*
@@ -143,9 +147,10 @@
 	 */
 	raw_spin_rq_lock_irq(cpu_rq(cpu));
 #endif
-
-	for (i = 0; i < CPUACCT_STAT_NSTATS; i++)
-		cpuusage->usages[i] = val;
+	*cpuusage = 0;
+	cpustat[CPUTIME_USER] = cpustat[CPUTIME_NICE] = 0;
+	cpustat[CPUTIME_SYSTEM] = cpustat[CPUTIME_IRQ] = 0;
+	cpustat[CPUTIME_SOFTIRQ] = 0;
 
 #ifndef CONFIG_64BIT
 	raw_spin_rq_unlock_irq(cpu_rq(cpu));
@@ -196,7 +201,7 @@
 		return -EINVAL;
 
 	for_each_possible_cpu(cpu)
-		cpuacct_cpuusage_write(ca, cpu, 0);
+		cpuacct_cpuusage_write(ca, cpu);
 
 	return 0;
 }
@@ -243,25 +248,10 @@
 	seq_puts(m, "\n");
 
 	for_each_possible_cpu(cpu) {
-		struct cpuacct_usage *cpuusage = per_cpu_ptr(ca->cpuusage, cpu);
-
 		seq_printf(m, "%d", cpu);
-
-		for (index = 0; index < CPUACCT_STAT_NSTATS; index++) {
-#ifndef CONFIG_64BIT
-			/*
-			 * Take rq->lock to make 64-bit read safe on 32-bit
-			 * platforms.
-			 */
-			raw_spin_rq_lock_irq(cpu_rq(cpu));
-#endif
-
-			seq_printf(m, " %llu", cpuusage->usages[index]);
-
-#ifndef CONFIG_64BIT
-			raw_spin_rq_unlock_irq(cpu_rq(cpu));
-#endif
-		}
+		for (index = 0; index < CPUACCT_STAT_NSTATS; index++)
+			seq_printf(m, " %llu",
+				   cpuacct_cpuusage_read(ca, cpu, index));
 		seq_puts(m, "\n");
 	}
 	return 0;
@@ -338,19 +328,13 @@
  */
 void cpuacct_charge(struct task_struct *tsk, u64 cputime)
 {
+	unsigned int cpu = task_cpu(tsk);
 	struct cpuacct *ca;
-	int index = CPUACCT_STAT_SYSTEM;
-	struct pt_regs *regs = get_irq_regs() ? : task_pt_regs(tsk);
 
-	if (regs && user_mode(regs))
-		index = CPUACCT_STAT_USER;
-
-	rcu_read_lock();
+	lockdep_assert_rq_held(cpu_rq(cpu));
 
 	for (ca = task_ca(tsk); ca; ca = parent_ca(ca))
-		__this_cpu_add(ca->cpuusage->usages[index], cputime);
-
-	rcu_read_unlock();
+		*per_cpu_ptr(ca->cpuusage, cpu) += cputime;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/cpudeadline.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/cpudeadline.c
@@ -124,7 +124,7 @@
 		unsigned long cap, max_cap = 0;
 		int cpu, max_cpu = -1;
 
-		if (!static_branch_unlikely(&sched_asym_cpucapacity))
+		if (!sched_asym_cpucap_active())
 			return 1;
 
 		/* Ensure the capacity of the CPUs fits the task. */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/cpufreq_schedutil.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/cpufreq_schedutil.c
@@ -91,7 +91,7 @@
 
 	if (unlikely(sg_policy->limits_changed)) {
 		sg_policy->limits_changed = false;
-		sg_policy->need_freq_update = true;
+		sg_policy->need_freq_update = cpufreq_driver_test_flags(CPUFREQ_NEED_UPDATE_LIMITS);
 		return true;
 	}
 
@@ -104,7 +104,7 @@
 				   unsigned int next_freq)
 {
 	if (sg_policy->need_freq_update)
-		sg_policy->need_freq_update = cpufreq_driver_test_flags(CPUFREQ_NEED_UPDATE_LIMITS);
+		sg_policy->need_freq_update = false;
 	else if (sg_policy->next_freq == next_freq)
 		return false;
 
@@ -289,6 +289,7 @@
 	 * into the same scale so we can compare.
 	 */
 	boost = (sg_cpu->iowait_boost * sg_cpu->max) >> SCHED_CAPACITY_SHIFT;
+	boost = uclamp_rq_util_with(cpu_rq(sg_cpu->cpu), boost, NULL);
 	if (sg_cpu->util < boost)
 		sg_cpu->util = boost;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/cpupri.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/cpupri.c
@@ -102,6 +102,7 @@
 
 	if (lowest_mask) {
 		cpumask_and(lowest_mask, &p->cpus_mask, vec->mask);
+		cpumask_and(lowest_mask, lowest_mask, cpu_active_mask);
 
 		/*
 		 * We have to ensure that we have at least one bit
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/cputime.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/cputime.c
@@ -148,10 +148,10 @@
 
 	/* Add guest time to cpustat. */
 	if (task_nice(p) > 0) {
-		cpustat[CPUTIME_NICE] += cputime;
+		task_group_account_field(p, CPUTIME_NICE, cputime);
 		cpustat[CPUTIME_GUEST_NICE] += cputime;
 	} else {
-		cpustat[CPUTIME_USER] += cputime;
+		task_group_account_field(p, CPUTIME_USER, cputime);
 		cpustat[CPUTIME_GUEST] += cputime;
 	}
 }
@@ -577,6 +577,12 @@
 	}
 
 	stime = mul_u64_u64_div_u64(stime, rtime, stime + utime);
+	/*
+	 * Because mul_u64_u64_div_u64() can approximate on some
+	 * achitectures; enforce the constraint that: a*b/(b+c) <= a.
+	 */
+	if (unlikely(stime > rtime))
+		stime = rtime;
 
 update:
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/deadline.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/deadline.c
@@ -17,6 +17,7 @@
  */
 #include "sched.h"
 #include "pelt.h"
+#include <linux/cpuset.h>
 
 struct dl_bandwidth def_dl_bandwidth;
 
@@ -112,7 +113,7 @@
  */
 static inline unsigned long dl_bw_capacity(int i)
 {
-	if (!static_branch_unlikely(&sched_asym_cpucapacity) &&
+	if (!sched_asym_cpucap_active() &&
 	    capacity_orig_of(i) == SCHED_CAPACITY_SCALE) {
 		return dl_bw_cpus(i) << SCHED_CAPACITY_SHIFT;
 	} else {
@@ -1265,8 +1266,8 @@
 		return;
 	}
 
-	schedstat_set(curr->se.statistics.exec_max,
-		      max(curr->se.statistics.exec_max, delta_exec));
+	schedstat_set(curr->stats.exec_max,
+		      max(curr->stats.exec_max, delta_exec));
 
 	curr->se.sum_exec_runtime += delta_exec;
 	account_group_exec_runtime(curr, delta_exec);
@@ -1561,7 +1562,10 @@
 		 * the throttle.
 		 */
 		p->dl.dl_throttled = 0;
-		BUG_ON(!is_dl_boosted(&p->dl) || flags != ENQUEUE_REPLENISH);
+		if (!(flags & ENQUEUE_REPLENISH))
+			printk_deferred_once("sched: DL de-boosted task PID %d: REPLENISH flag missing\n",
+					     task_pid_nr(p));
+
 		return;
 	}
 
@@ -1700,7 +1704,7 @@
 	 * Take the capacity of the CPU into account to
 	 * ensure it fits the requirement of the task.
 	 */
-	if (static_branch_unlikely(&sched_asym_cpucapacity))
+	if (sched_asym_cpucap_active())
 		select_rq |= !dl_task_fits_capacity(p, cpu);
 
 	if (select_rq) {
@@ -1720,6 +1724,7 @@
 
 static void migrate_task_rq_dl(struct task_struct *p, int new_cpu __maybe_unused)
 {
+	struct rq_flags rf;
 	struct rq *rq;
 
 	if (READ_ONCE(p->__state) != TASK_WAKING)
@@ -1731,7 +1736,7 @@
 	 * from try_to_wake_up(). Hence, p->pi_lock is locked, but
 	 * rq->lock is not... So, lock it
 	 */
-	raw_spin_rq_lock(rq);
+	rq_lock(rq, &rf);
 	if (p->dl.dl_non_contending) {
 		update_rq_clock(rq);
 		sub_running_bw(&p->dl, &rq->dl);
@@ -1747,7 +1752,7 @@
 			put_task_struct(p);
 	}
 	sub_rq_bw(&p->dl, &rq->dl);
-	raw_spin_rq_unlock(rq);
+	rq_unlock(rq, &rf);
 }
 
 static void check_preempt_equal_dl(struct rq *rq, struct task_struct *p)
@@ -1842,8 +1847,7 @@
 	deadline_queue_push_tasks(rq);
 }
 
-static struct sched_dl_entity *pick_next_dl_entity(struct rq *rq,
-						   struct dl_rq *dl_rq)
+static struct sched_dl_entity *pick_next_dl_entity(struct dl_rq *dl_rq)
 {
 	struct rb_node *left = rb_first_cached(&dl_rq->root);
 
@@ -1862,7 +1866,7 @@
 	if (!sched_dl_runnable(rq))
 		return NULL;
 
-	dl_se = pick_next_dl_entity(rq, dl_rq);
+	dl_se = pick_next_dl_entity(dl_rq);
 	BUG_ON(!dl_se);
 	p = dl_task_of(dl_se);
 
@@ -2081,6 +2085,7 @@
 				     !cpumask_test_cpu(later_rq->cpu, &task->cpus_mask) ||
 				     task_running(rq, task) ||
 				     !dl_task(task) ||
+				     is_migration_disabled(task) ||
 				     !task_on_rq_queued(task))) {
 				double_unlock_balance(rq, later_rq);
 				later_rq = NULL;
@@ -2145,12 +2150,6 @@
 		return 0;
 
 retry:
-	if (is_migration_disabled(next_task))
-		return 0;
-
-	if (WARN_ON(next_task == rq->curr))
-		return 0;
-
 	/*
 	 * If next_task preempts rq->curr, and rq->curr
 	 * can move away, it makes sense to just reschedule
@@ -2163,6 +2162,12 @@
 		return 0;
 	}
 
+	if (is_migration_disabled(next_task))
+		return 0;
+
+	if (WARN_ON(next_task == rq->curr))
+		return 0;
+
 	/* We might release rq lock */
 	get_task_struct(next_task);
 
@@ -2303,9 +2308,11 @@
 		double_unlock_balance(this_rq, src_rq);
 
 		if (push_task) {
+			preempt_disable();
 			raw_spin_rq_unlock(this_rq);
 			stop_one_cpu_nowait(src_rq->cpu, push_cpu_stop,
 					    push_task, &src_rq->push_work);
+			preempt_enable();
 			raw_spin_rq_lock(this_rq);
 		}
 	}
@@ -2442,6 +2449,12 @@
 	if (task_on_rq_queued(p) && p->dl.dl_runtime)
 		task_non_contending(p);
 
+	/*
+	 * In case a task is setscheduled out from SCHED_DEADLINE we need to
+	 * keep track of that on its cpuset (for correct bandwidth tracking).
+	 */
+	dec_dl_tasks_cs(p);
+
 	if (!task_on_rq_queued(p)) {
 		/*
 		 * Inactive timer is armed. However, p is leaving DEADLINE and
@@ -2482,6 +2495,12 @@
 	if (hrtimer_try_to_cancel(&p->dl.inactive_timer) == 1)
 		put_task_struct(p);
 
+	/*
+	 * In case a task is setscheduled to SCHED_DEADLINE we need to keep
+	 * track of that on its cpuset (for correct bandwidth tracking).
+	 */
+	inc_dl_tasks_cs(p);
+
 	/* If p is not queued we will update its parameters at next wakeup. */
 	if (!task_on_rq_queued(p)) {
 		add_rq_bw(&p->dl, &rq->dl);
@@ -2591,7 +2610,7 @@
 	 * value smaller than the currently allocated bandwidth in
 	 * any of the root_domains.
 	 */
-	for_each_possible_cpu(cpu) {
+	for_each_online_cpu(cpu) {
 		rcu_read_lock_sched();
 
 		if (dl_bw_visited(cpu, gen))
@@ -2860,41 +2879,6 @@
 }
 
 #ifdef CONFIG_SMP
-int dl_task_can_attach(struct task_struct *p, const struct cpumask *cs_cpus_allowed)
-{
-	unsigned long flags, cap;
-	unsigned int dest_cpu;
-	struct dl_bw *dl_b;
-	bool overflow;
-	int ret;
-
-	dest_cpu = cpumask_any_and(cpu_active_mask, cs_cpus_allowed);
-
-	rcu_read_lock_sched();
-	dl_b = dl_bw_of(dest_cpu);
-	raw_spin_lock_irqsave(&dl_b->lock, flags);
-	cap = dl_bw_capacity(dest_cpu);
-	overflow = __dl_overflow(dl_b, cap, 0, p->dl.dl_bw);
-	if (overflow) {
-		ret = -EBUSY;
-	} else {
-		/*
-		 * We reserve space for this task in the destination
-		 * root_domain, as we can't fail after this point.
-		 * We will free resources in the source root_domain
-		 * later on (see set_cpus_allowed_dl()).
-		 */
-		int cpus = dl_bw_cpus(dest_cpu);
-
-		__dl_add(dl_b, p->dl.dl_bw, cpus);
-		ret = 0;
-	}
-	raw_spin_unlock_irqrestore(&dl_b->lock, flags);
-	rcu_read_unlock_sched();
-
-	return ret;
-}
-
 int dl_cpuset_cpumask_can_shrink(const struct cpumask *cur,
 				 const struct cpumask *trial)
 {
@@ -2916,21 +2900,59 @@
 	return ret;
 }
 
-bool dl_cpu_busy(unsigned int cpu)
+enum dl_bw_request {
+	dl_bw_req_check_overflow = 0,
+	dl_bw_req_alloc,
+	dl_bw_req_free
+};
+
+static int dl_bw_manage(enum dl_bw_request req, int cpu, u64 dl_bw)
 {
-	unsigned long flags, cap;
+	unsigned long flags;
 	struct dl_bw *dl_b;
-	bool overflow;
+	bool overflow = 0;
 
 	rcu_read_lock_sched();
 	dl_b = dl_bw_of(cpu);
 	raw_spin_lock_irqsave(&dl_b->lock, flags);
-	cap = dl_bw_capacity(cpu);
-	overflow = __dl_overflow(dl_b, cap, 0, 0);
+
+	if (req == dl_bw_req_free) {
+		__dl_sub(dl_b, dl_bw, dl_bw_cpus(cpu));
+	} else {
+		unsigned long cap = dl_bw_capacity(cpu);
+
+		overflow = __dl_overflow(dl_b, cap, 0, dl_bw);
+
+		if (req == dl_bw_req_alloc && !overflow) {
+			/*
+			 * We reserve space in the destination
+			 * root_domain, as we can't fail after this point.
+			 * We will free resources in the source root_domain
+			 * later on (see set_cpus_allowed_dl()).
+			 */
+			__dl_add(dl_b, dl_bw, dl_bw_cpus(cpu));
+		}
+	}
+
 	raw_spin_unlock_irqrestore(&dl_b->lock, flags);
 	rcu_read_unlock_sched();
 
-	return overflow;
+	return overflow ? -EBUSY : 0;
+}
+
+int dl_bw_check_overflow(int cpu)
+{
+	return dl_bw_manage(dl_bw_req_check_overflow, cpu, 0);
+}
+
+int dl_bw_alloc(int cpu, u64 dl_bw)
+{
+	return dl_bw_manage(dl_bw_req_alloc, cpu, dl_bw);
+}
+
+void dl_bw_free(int cpu, u64 dl_bw)
+{
+	dl_bw_manage(dl_bw_req_free, cpu, dl_bw);
 }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/debug.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/debug.c
@@ -416,7 +416,7 @@
 		char buf[32];
 
 		snprintf(buf, sizeof(buf), "cpu%d", cpu);
-		debugfs_remove(debugfs_lookup(buf, sd_dentry));
+		debugfs_lookup_and_remove(buf, sd_dentry);
 		d_cpu = debugfs_create_dir(buf, sd_dentry);
 
 		i = 0;
@@ -448,9 +448,11 @@
 	struct sched_entity *se = tg->se[cpu];
 
 #define P(F)		SEQ_printf(m, "  .%-30s: %lld\n",	#F, (long long)F)
-#define P_SCHEDSTAT(F)	SEQ_printf(m, "  .%-30s: %lld\n",	#F, (long long)schedstat_val(F))
+#define P_SCHEDSTAT(F)	SEQ_printf(m, "  .%-30s: %lld\n",	\
+		#F, (long long)schedstat_val(stats->F))
 #define PN(F)		SEQ_printf(m, "  .%-30s: %lld.%06ld\n", #F, SPLIT_NS((long long)F))
-#define PN_SCHEDSTAT(F)	SEQ_printf(m, "  .%-30s: %lld.%06ld\n", #F, SPLIT_NS((long long)schedstat_val(F)))
+#define PN_SCHEDSTAT(F)	SEQ_printf(m, "  .%-30s: %lld.%06ld\n", \
+		#F, SPLIT_NS((long long)schedstat_val(stats->F)))
 
 	if (!se)
 		return;
@@ -460,16 +462,19 @@
 	PN(se->sum_exec_runtime);
 
 	if (schedstat_enabled()) {
-		PN_SCHEDSTAT(se->statistics.wait_start);
-		PN_SCHEDSTAT(se->statistics.sleep_start);
-		PN_SCHEDSTAT(se->statistics.block_start);
-		PN_SCHEDSTAT(se->statistics.sleep_max);
-		PN_SCHEDSTAT(se->statistics.block_max);
-		PN_SCHEDSTAT(se->statistics.exec_max);
-		PN_SCHEDSTAT(se->statistics.slice_max);
-		PN_SCHEDSTAT(se->statistics.wait_max);
-		PN_SCHEDSTAT(se->statistics.wait_sum);
-		P_SCHEDSTAT(se->statistics.wait_count);
+		struct sched_statistics *stats;
+		stats = __schedstats_from_se(se);
+
+		PN_SCHEDSTAT(wait_start);
+		PN_SCHEDSTAT(sleep_start);
+		PN_SCHEDSTAT(block_start);
+		PN_SCHEDSTAT(sleep_max);
+		PN_SCHEDSTAT(block_max);
+		PN_SCHEDSTAT(exec_max);
+		PN_SCHEDSTAT(slice_max);
+		PN_SCHEDSTAT(wait_max);
+		PN_SCHEDSTAT(wait_sum);
+		P_SCHEDSTAT(wait_count);
 	}
 
 	P(se->load.weight);
@@ -536,9 +541,9 @@
 		p->prio);
 
 	SEQ_printf(m, "%9Ld.%06ld %9Ld.%06ld %9Ld.%06ld",
-		SPLIT_NS(schedstat_val_or_zero(p->se.statistics.wait_sum)),
+		SPLIT_NS(schedstat_val_or_zero(p->stats.wait_sum)),
 		SPLIT_NS(p->se.sum_exec_runtime),
-		SPLIT_NS(schedstat_val_or_zero(p->se.statistics.sum_sleep_runtime)));
+		SPLIT_NS(schedstat_val_or_zero(p->stats.sum_sleep_runtime)));
 
 #ifdef CONFIG_NUMA_BALANCING
 	SEQ_printf(m, " %d %d", task_node(p), task_numa_group_id(p));
@@ -921,25 +926,15 @@
 static void sched_show_numa(struct task_struct *p, struct seq_file *m)
 {
 #ifdef CONFIG_NUMA_BALANCING
-	struct mempolicy *pol;
-
 	if (p->mm)
 		P(mm->numa_scan_seq);
 
-	task_lock(p);
-	pol = p->mempolicy;
-	if (pol && !(pol->flags & MPOL_F_MORON))
-		pol = NULL;
-	mpol_get(pol);
-	task_unlock(p);
-
 	P(numa_pages_migrated);
 	P(numa_preferred_nid);
 	P(total_numa_faults);
 	SEQ_printf(m, "current_node=%d, numa_group_id=%d\n",
 			task_node(p), task_numa_group_id(p));
 	show_numa_stats(p, m);
-	mpol_put(pol);
 #endif
 }
 
@@ -954,8 +949,8 @@
 		"---------------------------------------------------------"
 		"----------\n");
 
-#define P_SCHEDSTAT(F)  __PS(#F, schedstat_val(p->F))
-#define PN_SCHEDSTAT(F) __PSN(#F, schedstat_val(p->F))
+#define P_SCHEDSTAT(F)  __PS(#F, schedstat_val(p->stats.F))
+#define PN_SCHEDSTAT(F) __PSN(#F, schedstat_val(p->stats.F))
 
 	PN(se.exec_start);
 	PN(se.vruntime);
@@ -968,33 +963,33 @@
 	if (schedstat_enabled()) {
 		u64 avg_atom, avg_per_cpu;
 
-		PN_SCHEDSTAT(se.statistics.sum_sleep_runtime);
-		PN_SCHEDSTAT(se.statistics.wait_start);
-		PN_SCHEDSTAT(se.statistics.sleep_start);
-		PN_SCHEDSTAT(se.statistics.block_start);
-		PN_SCHEDSTAT(se.statistics.sleep_max);
-		PN_SCHEDSTAT(se.statistics.block_max);
-		PN_SCHEDSTAT(se.statistics.exec_max);
-		PN_SCHEDSTAT(se.statistics.slice_max);
-		PN_SCHEDSTAT(se.statistics.wait_max);
-		PN_SCHEDSTAT(se.statistics.wait_sum);
-		P_SCHEDSTAT(se.statistics.wait_count);
-		PN_SCHEDSTAT(se.statistics.iowait_sum);
-		P_SCHEDSTAT(se.statistics.iowait_count);
-		P_SCHEDSTAT(se.statistics.nr_migrations_cold);
-		P_SCHEDSTAT(se.statistics.nr_failed_migrations_affine);
-		P_SCHEDSTAT(se.statistics.nr_failed_migrations_running);
-		P_SCHEDSTAT(se.statistics.nr_failed_migrations_hot);
-		P_SCHEDSTAT(se.statistics.nr_forced_migrations);
-		P_SCHEDSTAT(se.statistics.nr_wakeups);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_sync);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_migrate);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_local);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_remote);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_affine);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_affine_attempts);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_passive);
-		P_SCHEDSTAT(se.statistics.nr_wakeups_idle);
+		PN_SCHEDSTAT(sum_sleep_runtime);
+		PN_SCHEDSTAT(wait_start);
+		PN_SCHEDSTAT(sleep_start);
+		PN_SCHEDSTAT(block_start);
+		PN_SCHEDSTAT(sleep_max);
+		PN_SCHEDSTAT(block_max);
+		PN_SCHEDSTAT(exec_max);
+		PN_SCHEDSTAT(slice_max);
+		PN_SCHEDSTAT(wait_max);
+		PN_SCHEDSTAT(wait_sum);
+		P_SCHEDSTAT(wait_count);
+		PN_SCHEDSTAT(iowait_sum);
+		P_SCHEDSTAT(iowait_count);
+		P_SCHEDSTAT(nr_migrations_cold);
+		P_SCHEDSTAT(nr_failed_migrations_affine);
+		P_SCHEDSTAT(nr_failed_migrations_running);
+		P_SCHEDSTAT(nr_failed_migrations_hot);
+		P_SCHEDSTAT(nr_forced_migrations);
+		P_SCHEDSTAT(nr_wakeups);
+		P_SCHEDSTAT(nr_wakeups_sync);
+		P_SCHEDSTAT(nr_wakeups_migrate);
+		P_SCHEDSTAT(nr_wakeups_local);
+		P_SCHEDSTAT(nr_wakeups_remote);
+		P_SCHEDSTAT(nr_wakeups_affine);
+		P_SCHEDSTAT(nr_wakeups_affine_attempts);
+		P_SCHEDSTAT(nr_wakeups_passive);
+		P_SCHEDSTAT(nr_wakeups_idle);
 
 		avg_atom = p->se.sum_exec_runtime;
 		if (nr_switches)
@@ -1060,7 +1055,7 @@
 void proc_sched_set_task(struct task_struct *p)
 {
 #ifdef CONFIG_SCHEDSTATS
-	memset(&p->se.statistics, 0, sizeof(p->se.statistics));
+	memset(&p->stats, 0, sizeof(p->stats));
 #endif
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/fair.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/fair.c
@@ -837,8 +837,13 @@
 
 	curr->exec_start = now;
 
-	schedstat_set(curr->statistics.exec_max,
-		      max(delta_exec, curr->statistics.exec_max));
+	if (schedstat_enabled()) {
+		struct sched_statistics *stats;
+
+		stats = __schedstats_from_se(curr);
+		__schedstat_set(stats->exec_max,
+				max(delta_exec, stats->exec_max));
+	}
 
 	curr->sum_exec_runtime += delta_exec;
 	schedstat_add(cfs_rq->exec_clock, delta_exec);
@@ -866,39 +871,45 @@
 update_stats_wait_start(struct cfs_rq *cfs_rq, struct sched_entity *se)
 {
 	u64 wait_start, prev_wait_start;
+	struct sched_statistics *stats;
 
 	if (!schedstat_enabled())
 		return;
 
+	stats = __schedstats_from_se(se);
+
 	wait_start = rq_clock(rq_of(cfs_rq));
-	prev_wait_start = schedstat_val(se->statistics.wait_start);
+	prev_wait_start = schedstat_val(stats->wait_start);
 
 	if (entity_is_task(se) && task_on_rq_migrating(task_of(se)) &&
 	    likely(wait_start > prev_wait_start))
 		wait_start -= prev_wait_start;
 
-	__schedstat_set(se->statistics.wait_start, wait_start);
+	__schedstat_set(stats->wait_start, wait_start);
 }
 
 static inline void
 update_stats_wait_end(struct cfs_rq *cfs_rq, struct sched_entity *se)
 {
-	struct task_struct *p;
+	struct sched_statistics *stats;
+	struct task_struct *p = NULL;
 	u64 delta;
 
 	if (!schedstat_enabled())
 		return;
 
+	stats = __schedstats_from_se(se);
+
 	/*
 	 * When the sched_schedstat changes from 0 to 1, some sched se
 	 * maybe already in the runqueue, the se->statistics.wait_start
 	 * will be 0.So it will let the delta wrong. We need to avoid this
 	 * scenario.
 	 */
-	if (unlikely(!schedstat_val(se->statistics.wait_start)))
+	if (unlikely(!schedstat_val(stats->wait_start)))
 		return;
 
-	delta = rq_clock(rq_of(cfs_rq)) - schedstat_val(se->statistics.wait_start);
+	delta = rq_clock(rq_of(cfs_rq)) - schedstat_val(stats->wait_start);
 
 	if (entity_is_task(se)) {
 		p = task_of(se);
@@ -908,30 +919,33 @@
 			 * time stamp can be adjusted to accumulate wait time
 			 * prior to migration.
 			 */
-			__schedstat_set(se->statistics.wait_start, delta);
+			__schedstat_set(stats->wait_start, delta);
 			return;
 		}
 		trace_sched_stat_wait(p, delta);
 	}
 
-	__schedstat_set(se->statistics.wait_max,
-		      max(schedstat_val(se->statistics.wait_max), delta));
-	__schedstat_inc(se->statistics.wait_count);
-	__schedstat_add(se->statistics.wait_sum, delta);
-	__schedstat_set(se->statistics.wait_start, 0);
+	__schedstat_set(stats->wait_max,
+		      max(schedstat_val(stats->wait_max), delta));
+	__schedstat_inc(stats->wait_count);
+	__schedstat_add(stats->wait_sum, delta);
+	__schedstat_set(stats->wait_start, 0);
 }
 
 static inline void
 update_stats_enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se)
 {
+	struct sched_statistics *stats;
 	struct task_struct *tsk = NULL;
 	u64 sleep_start, block_start;
 
 	if (!schedstat_enabled())
 		return;
 
-	sleep_start = schedstat_val(se->statistics.sleep_start);
-	block_start = schedstat_val(se->statistics.block_start);
+	stats = __schedstats_from_se(se);
+
+	sleep_start = schedstat_val(stats->sleep_start);
+	block_start = schedstat_val(stats->block_start);
 
 	if (entity_is_task(se))
 		tsk = task_of(se);
@@ -942,11 +956,11 @@
 		if ((s64)delta < 0)
 			delta = 0;
 
-		if (unlikely(delta > schedstat_val(se->statistics.sleep_max)))
-			__schedstat_set(se->statistics.sleep_max, delta);
+		if (unlikely(delta > schedstat_val(stats->sleep_max)))
+			__schedstat_set(stats->sleep_max, delta);
 
-		__schedstat_set(se->statistics.sleep_start, 0);
-		__schedstat_add(se->statistics.sum_sleep_runtime, delta);
+		__schedstat_set(stats->sleep_start, 0);
+		__schedstat_add(stats->sum_sleep_runtime, delta);
 
 		if (tsk) {
 			account_scheduler_latency(tsk, delta >> 10, 1);
@@ -959,31 +973,21 @@
 		if ((s64)delta < 0)
 			delta = 0;
 
-		if (unlikely(delta > schedstat_val(se->statistics.block_max)))
-			__schedstat_set(se->statistics.block_max, delta);
+		if (unlikely(delta > schedstat_val(stats->block_max)))
+			__schedstat_set(stats->block_max, delta);
 
-		__schedstat_set(se->statistics.block_start, 0);
-		__schedstat_add(se->statistics.sum_sleep_runtime, delta);
+		__schedstat_set(stats->block_start, 0);
+		__schedstat_add(stats->sum_sleep_runtime, delta);
 
 		if (tsk) {
 			if (tsk->in_iowait) {
-				__schedstat_add(se->statistics.iowait_sum, delta);
-				__schedstat_inc(se->statistics.iowait_count);
+				__schedstat_add(stats->iowait_sum, delta);
+				__schedstat_inc(stats->iowait_count);
 				trace_sched_stat_iowait(tsk, delta);
 			}
 
 			trace_sched_stat_blocked(tsk, delta);
 
-			/*
-			 * Blocking time is in units of nanosecs, so shift by
-			 * 20 to get a milliseconds-range estimation of the
-			 * amount of time that the task spent sleeping:
-			 */
-			if (unlikely(prof_on == SLEEP_PROFILING)) {
-				profile_hits(SLEEP_PROFILING,
-						(void *)get_wchan(tsk),
-						delta >> 20);
-			}
 			account_scheduler_latency(tsk, delta >> 10, 0);
 		}
 	}
@@ -1030,10 +1034,10 @@
 		/* XXX racy against TTWU */
 		state = READ_ONCE(tsk->__state);
 		if (state & TASK_INTERRUPTIBLE)
-			__schedstat_set(se->statistics.sleep_start,
+			__schedstat_set(tsk->stats.sleep_start,
 				      rq_clock(rq_of(cfs_rq)));
 		if (state & TASK_UNINTERRUPTIBLE)
-			__schedstat_set(se->statistics.block_start,
+			__schedstat_set(tsk->stats.block_start,
 				      rq_clock(rq_of(cfs_rq)));
 	}
 }
@@ -3107,15 +3111,14 @@
 
 }
 
-void reweight_task(struct task_struct *p, int prio)
+void reweight_task(struct task_struct *p, const struct load_weight *lw)
 {
 	struct sched_entity *se = &p->se;
 	struct cfs_rq *cfs_rq = cfs_rq_of(se);
 	struct load_weight *load = &se->load;
-	unsigned long weight = scale_load(sched_prio_to_weight[prio]);
 
-	reweight_entity(cfs_rq, se, weight);
-	load->inv_weight = sched_prio_to_wmult[prio];
+	reweight_entity(cfs_rq, se, lw->weight);
+	load->inv_weight = lw->inv_weight;
 }
 
 #ifdef CONFIG_FAIR_GROUP_SCHED
@@ -3300,15 +3303,17 @@
 {
 	struct cfs_rq *prev_cfs_rq;
 	struct list_head *prev;
+	struct rq *rq = rq_of(cfs_rq);
 
 	if (cfs_rq->on_list) {
 		prev = cfs_rq->leaf_cfs_rq_list.prev;
 	} else {
-		struct rq *rq = rq_of(cfs_rq);
-
 		prev = rq->tmp_alone_branch;
 	}
 
+	if (prev == &rq->leaf_cfs_rq_list)
+		return false;
+
 	prev_cfs_rq = container_of(prev, struct cfs_rq, leaf_cfs_rq_list);
 
 	return (prev_cfs_rq->tg->parent == cfs_rq->tg);
@@ -3359,7 +3364,8 @@
  */
 static inline void update_tg_load_avg(struct cfs_rq *cfs_rq)
 {
-	long delta = cfs_rq->avg.load_avg - cfs_rq->tg_load_avg_contrib;
+	long delta;
+	u64 now;
 
 	/*
 	 * No need to update load_avg for root_task_group as it is not used.
@@ -3367,9 +3373,19 @@
 	if (cfs_rq->tg == &root_task_group)
 		return;
 
+	/*
+	 * For migration heavy workloads, access to tg->load_avg can be
+	 * unbound. Limit the update rate to at most once per ms.
+	 */
+	now = sched_clock_cpu(cpu_of(rq_of(cfs_rq)));
+	if (now - cfs_rq->last_update_tg_load_avg < NSEC_PER_MSEC)
+		return;
+
+	delta = cfs_rq->avg.load_avg - cfs_rq->tg_load_avg_contrib;
 	if (abs(delta) > cfs_rq->tg_load_avg_contrib / 64) {
 		atomic_long_add(delta, &cfs_rq->tg->load_avg);
 		cfs_rq->tg_load_avg_contrib = cfs_rq->avg.load_avg;
+		cfs_rq->last_update_tg_load_avg = now;
 	}
 }
 
@@ -3422,7 +3438,6 @@
 	se->avg.last_update_time = n_last_update_time;
 }
 
-
 /*
  * When on migration a sched_entity joins/leaves the PELT hierarchy, we need to
  * propagate its contribution. The key to this propagation is the invariant
@@ -3490,7 +3505,6 @@
  * XXX: only do this for the part of runnable > running ?
  *
  */
-
 static inline void
 update_tg_cfs_util(struct cfs_rq *cfs_rq, struct sched_entity *se, struct cfs_rq *gcfs_rq)
 {
@@ -3722,7 +3736,19 @@
 
 		r = removed_util;
 		sub_positive(&sa->util_avg, r);
-		sa->util_sum = sa->util_avg * divider;
+		sub_positive(&sa->util_sum, r * divider);
+		/*
+		 * Because of rounding, se->util_sum might ends up being +1 more than
+		 * cfs->util_sum. Although this is not a problem by itself, detaching
+		 * a lot of tasks with the rounding problem between 2 updates of
+		 * util_avg (~1ms) can make cfs->util_sum becoming null whereas
+		 * cfs_util_avg is not.
+		 * Check that util_sum is still above its lower bound for the new
+		 * util_avg. Given that period_contrib might have moved since the last
+		 * sync, we are only sure that util_sum must be above or equal to
+		 *    util_avg * minimum possible divider
+		 */
+		sa->util_sum = max_t(u32, sa->util_sum, sa->util_avg * PELT_MIN_DIVIDER);
 
 		r = removed_runnable;
 		sub_positive(&sa->runnable_avg, r);
@@ -3784,11 +3810,11 @@
 
 	se->avg.runnable_sum = se->avg.runnable_avg * divider;
 
-	se->avg.load_sum = divider;
-	if (se_weight(se)) {
-		se->avg.load_sum =
-			div_u64(se->avg.load_avg * se->avg.load_sum, se_weight(se));
-	}
+	se->avg.load_sum = se->avg.load_avg * divider;
+	if (se_weight(se) < se->avg.load_sum)
+		se->avg.load_sum = div_u64(se->avg.load_sum, se_weight(se));
+	else
+		se->avg.load_sum = 1;
 
 	enqueue_load_avg(cfs_rq, se);
 	cfs_rq->avg.util_avg += se->avg.util_avg;
@@ -3963,20 +3989,6 @@
 	return max(task_util(p), _task_util_est(p));
 }
 
-#ifdef CONFIG_UCLAMP_TASK
-static inline unsigned long uclamp_task_util(struct task_struct *p)
-{
-	return clamp(task_util_est(p),
-		     uclamp_eff_value(p, UCLAMP_MIN),
-		     uclamp_eff_value(p, UCLAMP_MAX));
-}
-#else
-static inline unsigned long uclamp_task_util(struct task_struct *p)
-{
-	return task_util_est(p);
-}
-#endif
-
 static inline void util_est_enqueue(struct cfs_rq *cfs_rq,
 				    struct task_struct *p)
 {
@@ -4110,14 +4122,144 @@
 	trace_sched_util_est_se_tp(&p->se);
 }
 
-static inline int task_fits_capacity(struct task_struct *p, long capacity)
+static inline int util_fits_cpu(unsigned long util,
+				unsigned long uclamp_min,
+				unsigned long uclamp_max,
+				int cpu)
+{
+	unsigned long capacity_orig, capacity_orig_thermal;
+	unsigned long capacity = capacity_of(cpu);
+	bool fits, uclamp_max_fits;
+
+	/*
+	 * Check if the real util fits without any uclamp boost/cap applied.
+	 */
+	fits = fits_capacity(util, capacity);
+
+	if (!uclamp_is_used())
+		return fits;
+
+	/*
+	 * We must use capacity_orig_of() for comparing against uclamp_min and
+	 * uclamp_max. We only care about capacity pressure (by using
+	 * capacity_of()) for comparing against the real util.
+	 *
+	 * If a task is boosted to 1024 for example, we don't want a tiny
+	 * pressure to skew the check whether it fits a CPU or not.
+	 *
+	 * Similarly if a task is capped to capacity_orig_of(little_cpu), it
+	 * should fit a little cpu even if there's some pressure.
+	 *
+	 * Only exception is for thermal pressure since it has a direct impact
+	 * on available OPP of the system.
+	 *
+	 * We honour it for uclamp_min only as a drop in performance level
+	 * could result in not getting the requested minimum performance level.
+	 *
+	 * For uclamp_max, we can tolerate a drop in performance level as the
+	 * goal is to cap the task. So it's okay if it's getting less.
+	 *
+	 * In case of capacity inversion we should honour the inverted capacity
+	 * for both uclamp_min and uclamp_max all the time.
+	 */
+	capacity_orig = cpu_in_capacity_inversion(cpu);
+	if (capacity_orig) {
+		capacity_orig_thermal = capacity_orig;
+	} else {
+		capacity_orig = capacity_orig_of(cpu);
+		capacity_orig_thermal = capacity_orig - arch_scale_thermal_pressure(cpu);
+	}
+
+	/*
+	 * We want to force a task to fit a cpu as implied by uclamp_max.
+	 * But we do have some corner cases to cater for..
+	 *
+	 *
+	 *                                 C=z
+	 *   |                             ___
+	 *   |                  C=y       |   |
+	 *   |_ _ _ _ _ _ _ _ _ ___ _ _ _ | _ | _ _ _ _ _  uclamp_max
+	 *   |      C=x        |   |      |   |
+	 *   |      ___        |   |      |   |
+	 *   |     |   |       |   |      |   |    (util somewhere in this region)
+	 *   |     |   |       |   |      |   |
+	 *   |     |   |       |   |      |   |
+	 *   +----------------------------------------
+	 *         cpu0        cpu1       cpu2
+	 *
+	 *   In the above example if a task is capped to a specific performance
+	 *   point, y, then when:
+	 *
+	 *   * util = 80% of x then it does not fit on cpu0 and should migrate
+	 *     to cpu1
+	 *   * util = 80% of y then it is forced to fit on cpu1 to honour
+	 *     uclamp_max request.
+	 *
+	 *   which is what we're enforcing here. A task always fits if
+	 *   uclamp_max <= capacity_orig. But when uclamp_max > capacity_orig,
+	 *   the normal upmigration rules should withhold still.
+	 *
+	 *   Only exception is when we are on max capacity, then we need to be
+	 *   careful not to block overutilized state. This is so because:
+	 *
+	 *     1. There's no concept of capping at max_capacity! We can't go
+	 *        beyond this performance level anyway.
+	 *     2. The system is being saturated when we're operating near
+	 *        max capacity, it doesn't make sense to block overutilized.
+	 */
+	uclamp_max_fits = (capacity_orig == SCHED_CAPACITY_SCALE) && (uclamp_max == SCHED_CAPACITY_SCALE);
+	uclamp_max_fits = !uclamp_max_fits && (uclamp_max <= capacity_orig);
+	fits = fits || uclamp_max_fits;
+
+	/*
+	 *
+	 *                                 C=z
+	 *   |                             ___       (region a, capped, util >= uclamp_max)
+	 *   |                  C=y       |   |
+	 *   |_ _ _ _ _ _ _ _ _ ___ _ _ _ | _ | _ _ _ _ _ uclamp_max
+	 *   |      C=x        |   |      |   |
+	 *   |      ___        |   |      |   |      (region b, uclamp_min <= util <= uclamp_max)
+	 *   |_ _ _|_ _|_ _ _ _| _ | _ _ _| _ | _ _ _ _ _ uclamp_min
+	 *   |     |   |       |   |      |   |
+	 *   |     |   |       |   |      |   |      (region c, boosted, util < uclamp_min)
+	 *   +----------------------------------------
+	 *         cpu0        cpu1       cpu2
+	 *
+	 * a) If util > uclamp_max, then we're capped, we don't care about
+	 *    actual fitness value here. We only care if uclamp_max fits
+	 *    capacity without taking margin/pressure into account.
+	 *    See comment above.
+	 *
+	 * b) If uclamp_min <= util <= uclamp_max, then the normal
+	 *    fits_capacity() rules apply. Except we need to ensure that we
+	 *    enforce we remain within uclamp_max, see comment above.
+	 *
+	 * c) If util < uclamp_min, then we are boosted. Same as (b) but we
+	 *    need to take into account the boosted value fits the CPU without
+	 *    taking margin/pressure into account.
+	 *
+	 * Cases (a) and (b) are handled in the 'fits' variable already. We
+	 * just need to consider an extra check for case (c) after ensuring we
+	 * handle the case uclamp_min > uclamp_max.
+	 */
+	uclamp_min = min(uclamp_min, uclamp_max);
+	if (util < uclamp_min && capacity_orig != SCHED_CAPACITY_SCALE)
+		fits = fits && (uclamp_min <= capacity_orig_thermal);
+
+	return fits;
+}
+
+static inline int task_fits_cpu(struct task_struct *p, int cpu)
 {
-	return fits_capacity(uclamp_task_util(p), capacity);
+	unsigned long uclamp_min = uclamp_eff_value(p, UCLAMP_MIN);
+	unsigned long uclamp_max = uclamp_eff_value(p, UCLAMP_MAX);
+	unsigned long util = task_util_est(p);
+	return util_fits_cpu(util, uclamp_min, uclamp_max, cpu);
 }
 
 static inline void update_misfit_status(struct task_struct *p, struct rq *rq)
 {
-	if (!static_branch_unlikely(&sched_asym_cpucapacity))
+	if (!sched_asym_cpucap_active())
 		return;
 
 	if (!p || p->nr_cpus_allowed == 1) {
@@ -4125,7 +4267,7 @@
 		return;
 	}
 
-	if (task_fits_capacity(p, capacity_of(cpu_of(rq)))) {
+	if (task_fits_cpu(p, cpu_of(rq))) {
 		rq->misfit_task_load = 0;
 		return;
 	}
@@ -4191,6 +4333,29 @@
 #endif
 }
 
+static inline bool entity_is_long_sleeper(struct sched_entity *se)
+{
+	struct cfs_rq *cfs_rq;
+	u64 sleep_time;
+
+	if (se->exec_start == 0)
+		return false;
+
+	cfs_rq = cfs_rq_of(se);
+
+	sleep_time = rq_clock_task(rq_of(cfs_rq));
+
+	/* Happen while migrating because of clock task divergence */
+	if (sleep_time <= se->exec_start)
+		return false;
+
+	sleep_time -= se->exec_start;
+	if (sleep_time > ((1ULL << 63) / scale_load_down(NICE_0_LOAD)))
+		return true;
+
+	return false;
+}
+
 static void
 place_entity(struct cfs_rq *cfs_rq, struct sched_entity *se, int initial)
 {
@@ -4219,8 +4384,29 @@
 		vruntime -= thresh;
 	}
 
-	/* ensure we never gain time by being placed backwards. */
-	se->vruntime = max_vruntime(se->vruntime, vruntime);
+	/*
+	 * Pull vruntime of the entity being placed to the base level of
+	 * cfs_rq, to prevent boosting it if placed backwards.
+	 * However, min_vruntime can advance much faster than real time, with
+	 * the extreme being when an entity with the minimal weight always runs
+	 * on the cfs_rq. If the waking entity slept for a long time, its
+	 * vruntime difference from min_vruntime may overflow s64 and their
+	 * comparison may get inversed, so ignore the entity's original
+	 * vruntime in that case.
+	 * The maximal vruntime speedup is given by the ratio of normal to
+	 * minimal weight: scale_load_down(NICE_0_LOAD) / MIN_SHARES.
+	 * When placing a migrated waking entity, its exec_start has been set
+	 * from a different rq. In order to take into account a possible
+	 * divergence between new and prev rq's clocks task because of irq and
+	 * stolen time, we take an additional margin.
+	 * So, cutting off on the sleep time of
+	 *     2^63 / scale_load_down(NICE_0_LOAD) ~ 104 days
+	 * should be safe.
+	 */
+	if (entity_is_long_sleeper(se))
+		se->vruntime = vruntime;
+	else
+		se->vruntime = max_vruntime(se->vruntime, vruntime);
 }
 
 static void check_enqueue_throttle(struct cfs_rq *cfs_rq);
@@ -4316,6 +4502,9 @@
 
 	if (flags & ENQUEUE_WAKEUP)
 		place_entity(cfs_rq, se, 0);
+	/* Entity has migrated, no longer consider this task hot */
+	if (flags & ENQUEUE_MIGRATED)
+		se->exec_start = 0;
 
 	check_schedstat_required();
 	update_stats_enqueue(cfs_rq, se, flags);
@@ -4502,9 +4691,12 @@
 	 */
 	if (schedstat_enabled() &&
 	    rq_of(cfs_rq)->cfs.load.weight >= 2*se->load.weight) {
-		schedstat_set(se->statistics.slice_max,
-			max((u64)schedstat_val(se->statistics.slice_max),
-			    se->sum_exec_runtime - se->prev_sum_exec_runtime));
+		struct sched_statistics *stats;
+
+		stats = __schedstats_from_se(se);
+		__schedstat_set(stats->slice_max,
+				max((u64)stats->slice_max,
+				    se->sum_exec_runtime - se->prev_sum_exec_runtime));
 	}
 
 	se->prev_sum_exec_runtime = se->sum_exec_runtime;
@@ -4802,8 +4994,8 @@
 
 	cfs_rq->throttle_count--;
 	if (!cfs_rq->throttle_count) {
-		cfs_rq->throttled_clock_task_time += rq_clock_task(rq) -
-					     cfs_rq->throttled_clock_task;
+		cfs_rq->throttled_clock_pelt_time += rq_clock_pelt(rq) -
+					     cfs_rq->throttled_clock_pelt;
 
 		/* Add cfs_rq with load or one or more already running entities to the list */
 		if (!cfs_rq_is_decayed(cfs_rq) || cfs_rq->nr_running)
@@ -4820,7 +5012,7 @@
 
 	/* group is entering throttled state, stop time */
 	if (!cfs_rq->throttle_count) {
-		cfs_rq->throttled_clock_task = rq_clock_task(rq);
+		cfs_rq->throttled_clock_pelt = rq_clock_pelt(rq);
 		list_del_leaf_cfs_rq(cfs_rq);
 	}
 	cfs_rq->throttle_count++;
@@ -5264,7 +5456,7 @@
 	pcfs_rq = tg->parent->cfs_rq[cpu];
 
 	cfs_rq->throttle_count = pcfs_rq->throttle_count;
-	cfs_rq->throttled_clock_task = rq_clock_task(cpu_rq(cpu));
+	cfs_rq->throttled_clock_pelt = rq_clock_pelt(cpu_rq(cpu));
 }
 
 /* conditionally throttle active cfs_rq's from put_prev_entity() */
@@ -5556,18 +5748,41 @@
 
 static inline bool cpu_overutilized(int cpu)
 {
-	return !fits_capacity(cpu_util(cpu), capacity_of(cpu));
+	unsigned long  rq_util_min, rq_util_max;
+
+	if (!sched_energy_enabled())
+		return false;
+
+	rq_util_min = uclamp_rq_get(cpu_rq(cpu), UCLAMP_MIN);
+	rq_util_max = uclamp_rq_get(cpu_rq(cpu), UCLAMP_MAX);
+
+	return !util_fits_cpu(cpu_util(cpu), rq_util_min, rq_util_max, cpu);
+}
+
+static inline void set_rd_overutilized_status(struct root_domain *rd,
+					      unsigned int status)
+{
+	if (!sched_energy_enabled())
+		return;
+
+	WRITE_ONCE(rd->overutilized, status);
+	trace_sched_overutilized_tp(rd, !!status);
 }
 
-static inline void update_overutilized_status(struct rq *rq)
+static inline void check_update_overutilized_status(struct rq *rq)
 {
-	if (!READ_ONCE(rq->rd->overutilized) && cpu_overutilized(rq->cpu)) {
-		WRITE_ONCE(rq->rd->overutilized, SG_OVERUTILIZED);
-		trace_sched_overutilized_tp(rq->rd, SG_OVERUTILIZED);
-	}
+	/*
+	 * overutilized field is used for load balancing decisions only
+	 * if energy aware scheduler is being used
+	 */
+	if (!sched_energy_enabled())
+		return;
+
+	if (!READ_ONCE(rq->rd->overutilized) && cpu_overutilized(rq->cpu))
+		set_rd_overutilized_status(rq->rd, SG_OVERUTILIZED);
 }
 #else
-static inline void update_overutilized_status(struct rq *rq) { }
+static inline void check_update_overutilized_status(struct rq *rq) { }
 #endif
 
 /* Runqueue only has SCHED_IDLE tasks enqueued */
@@ -5675,7 +5890,7 @@
 	 * and the following generally works well enough in practice.
 	 */
 	if (!task_new)
-		update_overutilized_status(rq);
+		check_update_overutilized_status(rq);
 
 enqueue_throttle:
 	if (cfs_bandwidth_used()) {
@@ -5997,12 +6212,12 @@
 	if (sched_feat(WA_WEIGHT) && target == nr_cpumask_bits)
 		target = wake_affine_weight(sd, p, this_cpu, prev_cpu, sync);
 
-	schedstat_inc(p->se.statistics.nr_wakeups_affine_attempts);
-	if (target == nr_cpumask_bits)
+	schedstat_inc(p->stats.nr_wakeups_affine_attempts);
+	if (target != this_cpu)
 		return prev_cpu;
 
 	schedstat_inc(sd->ttwu_move_affine);
-	schedstat_inc(p->se.statistics.nr_wakeups_affine);
+	schedstat_inc(p->stats.nr_wakeups_affine);
 	return target;
 }
 
@@ -6201,7 +6416,7 @@
 		if (!available_idle_cpu(cpu)) {
 			idle = false;
 			if (*idle_cpu == -1) {
-				if (sched_idle_cpu(cpu) && cpumask_test_cpu(cpu, p->cpus_ptr)) {
+				if (sched_idle_cpu(cpu) && cpumask_test_cpu(cpu, cpus)) {
 					*idle_cpu = cpu;
 					break;
 				}
@@ -6209,7 +6424,7 @@
 			}
 			break;
 		}
-		if (*idle_cpu == -1 && cpumask_test_cpu(cpu, p->cpus_ptr))
+		if (*idle_cpu == -1 && cpumask_test_cpu(cpu, cpus))
 			*idle_cpu = cpu;
 	}
 
@@ -6270,6 +6485,7 @@
 {
 	struct cpumask *cpus = this_cpu_cpumask_var_ptr(select_idle_mask);
 	int i, cpu, idle_cpu = -1, nr = INT_MAX;
+	struct sched_domain_shared *sd_share;
 	struct rq *this_rq = this_rq();
 	int this = smp_processor_id();
 	struct sched_domain *this_sd;
@@ -6309,6 +6525,17 @@
 		time = cpu_clock(this);
 	}
 
+	if (sched_feat(SIS_UTIL)) {
+		sd_share = rcu_dereference(per_cpu(sd_llc_shared, target));
+		if (sd_share) {
+			/* because !--nr is the condition to stop scan */
+			nr = READ_ONCE(sd_share->nr_idle_scan) + 1;
+			/* overloaded LLC is unlikely to have idle cpu/core */
+			if (nr == 1)
+				return -1;
+		}
+	}
+
 	for_each_cpu_wrap(cpu, cpus, target + 1) {
 		if (has_idle_core) {
 			i = select_idle_core(p, cpu, cpus, &idle_cpu);
@@ -6350,21 +6577,23 @@
 static int
 select_idle_capacity(struct task_struct *p, struct sched_domain *sd, int target)
 {
-	unsigned long task_util, best_cap = 0;
+	unsigned long task_util, util_min, util_max, best_cap = 0;
 	int cpu, best_cpu = -1;
 	struct cpumask *cpus;
 
 	cpus = this_cpu_cpumask_var_ptr(select_idle_mask);
 	cpumask_and(cpus, sched_domain_span(sd), p->cpus_ptr);
 
-	task_util = uclamp_task_util(p);
+	task_util = task_util_est(p);
+	util_min = uclamp_eff_value(p, UCLAMP_MIN);
+	util_max = uclamp_eff_value(p, UCLAMP_MAX);
 
 	for_each_cpu_wrap(cpu, cpus, target) {
 		unsigned long cpu_cap = capacity_of(cpu);
 
 		if (!available_idle_cpu(cpu) && !sched_idle_cpu(cpu))
 			continue;
-		if (fits_capacity(task_util, cpu_cap))
+		if (util_fits_cpu(task_util, util_min, util_max, cpu))
 			return cpu;
 
 		if (cpu_cap > best_cap) {
@@ -6376,10 +6605,13 @@
 	return best_cpu;
 }
 
-static inline bool asym_fits_capacity(int task_util, int cpu)
+static inline bool asym_fits_cpu(unsigned long util,
+				 unsigned long util_min,
+				 unsigned long util_max,
+				 int cpu)
 {
-	if (static_branch_unlikely(&sched_asym_cpucapacity))
-		return fits_capacity(task_util, capacity_of(cpu));
+	if (sched_asym_cpucap_active())
+		return util_fits_cpu(util, util_min, util_max, cpu);
 
 	return true;
 }
@@ -6391,16 +6623,18 @@
 {
 	bool has_idle_core = false;
 	struct sched_domain *sd;
-	unsigned long task_util;
+	unsigned long task_util, util_min, util_max;
 	int i, recent_used_cpu;
 
 	/*
 	 * On asymmetric system, update task utilization because we will check
 	 * that the task fits with cpu's capacity.
 	 */
-	if (static_branch_unlikely(&sched_asym_cpucapacity)) {
+	if (sched_asym_cpucap_active()) {
 		sync_entity_load_avg(&p->se);
-		task_util = uclamp_task_util(p);
+		task_util = task_util_est(p);
+		util_min = uclamp_eff_value(p, UCLAMP_MIN);
+		util_max = uclamp_eff_value(p, UCLAMP_MAX);
 	}
 
 	/*
@@ -6409,7 +6643,7 @@
 	lockdep_assert_irqs_disabled();
 
 	if ((available_idle_cpu(target) || sched_idle_cpu(target)) &&
-	    asym_fits_capacity(task_util, target))
+	    asym_fits_cpu(task_util, util_min, util_max, target))
 		return target;
 
 	/*
@@ -6417,7 +6651,7 @@
 	 */
 	if (prev != target && cpus_share_cache(prev, target) &&
 	    (available_idle_cpu(prev) || sched_idle_cpu(prev)) &&
-	    asym_fits_capacity(task_util, prev))
+	    asym_fits_cpu(task_util, util_min, util_max, prev))
 		return prev;
 
 	/*
@@ -6429,8 +6663,10 @@
 	 * pattern is IO completions.
 	 */
 	if (is_per_cpu_kthread(current) &&
+	    in_task() &&
 	    prev == smp_processor_id() &&
-	    this_rq()->nr_running <= 1) {
+	    this_rq()->nr_running <= 1 &&
+	    asym_fits_cpu(task_util, util_min, util_max, prev)) {
 		return prev;
 	}
 
@@ -6442,12 +6678,7 @@
 	    cpus_share_cache(recent_used_cpu, target) &&
 	    (available_idle_cpu(recent_used_cpu) || sched_idle_cpu(recent_used_cpu)) &&
 	    cpumask_test_cpu(p->recent_used_cpu, p->cpus_ptr) &&
-	    asym_fits_capacity(task_util, recent_used_cpu)) {
-		/*
-		 * Replace recent_used_cpu with prev as it is a potential
-		 * candidate for the next wake:
-		 */
-		p->recent_used_cpu = prev;
+	    asym_fits_cpu(task_util, util_min, util_max, recent_used_cpu)) {
 		return recent_used_cpu;
 	}
 
@@ -6455,7 +6686,7 @@
 	 * For asymmetric CPU capacity systems, our domain of interest is
 	 * sd_asym_cpucapacity rather than sd_llc.
 	 */
-	if (static_branch_unlikely(&sched_asym_cpucapacity)) {
+	if (sched_asym_cpucap_active()) {
 		sd = rcu_dereference(per_cpu(sd_asym_cpucapacity, target));
 		/*
 		 * On an asymmetric CPU capacity system where an exclusive
@@ -6786,6 +7017,8 @@
 static int find_energy_efficient_cpu(struct task_struct *p, int prev_cpu)
 {
 	unsigned long prev_delta = ULONG_MAX, best_delta = ULONG_MAX;
+	unsigned long p_util_min = uclamp_is_used() ? uclamp_eff_value(p, UCLAMP_MIN) : 0;
+	unsigned long p_util_max = uclamp_is_used() ? uclamp_eff_value(p, UCLAMP_MAX) : 1024;
 	struct root_domain *rd = cpu_rq(smp_processor_id())->rd;
 	int cpu, best_energy_cpu = prev_cpu, target = -1;
 	unsigned long cpu_cap, util, base_energy = 0;
@@ -6810,16 +7043,20 @@
 	target = prev_cpu;
 
 	sync_entity_load_avg(&p->se);
-	if (!task_util_est(p))
+	if (!task_util_est(p) && p_util_min == 0)
 		goto unlock;
 
 	for (; pd; pd = pd->next) {
+		unsigned long util_min = p_util_min, util_max = p_util_max;
 		unsigned long cur_delta, spare_cap, max_spare_cap = 0;
+		unsigned long rq_util_min, rq_util_max;
 		bool compute_prev_delta = false;
 		unsigned long base_energy_pd;
 		int max_spare_cap_cpu = -1;
 
 		for_each_cpu_and(cpu, perf_domain_span(pd), sched_domain_span(sd)) {
+			struct rq *rq = cpu_rq(cpu);
+
 			if (!cpumask_test_cpu(cpu, p->cpus_ptr))
 				continue;
 
@@ -6835,8 +7072,21 @@
 			 * much capacity we can get out of the CPU; this is
 			 * aligned with sched_cpu_util().
 			 */
-			util = uclamp_rq_util_with(cpu_rq(cpu), util, p);
-			if (!fits_capacity(util, cpu_cap))
+			if (uclamp_is_used() && !uclamp_rq_is_idle(rq)) {
+				/*
+				 * Open code uclamp_rq_util_with() except for
+				 * the clamp() part. Ie: apply max aggregation
+				 * only. util_fits_cpu() logic requires to
+				 * operate on non clamped util but must use the
+				 * max-aggregated uclamp_{min, max}.
+				 */
+				rq_util_min = uclamp_rq_get(rq, UCLAMP_MIN);
+				rq_util_max = uclamp_rq_get(rq, UCLAMP_MAX);
+
+				util_min = max(rq_util_min, p_util_min);
+				util_max = max(rq_util_max, p_util_max);
+			}
+			if (!util_fits_cpu(util, util_min, util_max, cpu))
 				continue;
 
 			if (cpu == prev_cpu) {
@@ -7027,9 +7277,6 @@
 	/* Tell new CPU we are migrated */
 	p->se.avg.last_update_time = 0;
 
-	/* We have migrated, no longer consider this task hot */
-	p->se.exec_start = 0;
-
 	update_scan_period(p, new_cpu);
 }
 
@@ -7788,6 +8035,8 @@
 	int tsk_cache_hot;
 
 	lockdep_assert_rq_held(env->src_rq);
+	if (p->sched_task_hot)
+		p->sched_task_hot = 0;
 
 	/*
 	 * We do not migrate tasks that are:
@@ -7806,7 +8055,7 @@
 	if (!cpumask_test_cpu(env->dst_cpu, p->cpus_ptr)) {
 		int cpu;
 
-		schedstat_inc(p->se.statistics.nr_failed_migrations_affine);
+		schedstat_inc(p->stats.nr_failed_migrations_affine);
 
 		env->flags |= LBF_SOME_PINNED;
 
@@ -7840,7 +8089,7 @@
 	env->flags &= ~LBF_ALL_PINNED;
 
 	if (task_running(env->src_rq, p)) {
-		schedstat_inc(p->se.statistics.nr_failed_migrations_running);
+		schedstat_inc(p->stats.nr_failed_migrations_running);
 		return 0;
 	}
 
@@ -7860,14 +8109,12 @@
 
 	if (tsk_cache_hot <= 0 ||
 	    env->sd->nr_balance_failed > env->sd->cache_nice_tries) {
-		if (tsk_cache_hot == 1) {
-			schedstat_inc(env->sd->lb_hot_gained[env->idle]);
-			schedstat_inc(p->se.statistics.nr_forced_migrations);
-		}
+		if (tsk_cache_hot == 1)
+			p->sched_task_hot = 1;
 		return 1;
 	}
 
-	schedstat_inc(p->se.statistics.nr_failed_migrations_hot);
+	schedstat_inc(p->stats.nr_failed_migrations_hot);
 	return 0;
 }
 
@@ -7878,6 +8125,12 @@
 {
 	lockdep_assert_rq_held(env->src_rq);
 
+	if (p->sched_task_hot) {
+		p->sched_task_hot = 0;
+		schedstat_inc(env->sd->lb_hot_gained[env->idle]);
+		schedstat_inc(p->stats.nr_forced_migrations);
+	}
+
 	deactivate_task(env->src_rq, p, DEQUEUE_NOCLOCK);
 	set_task_cpu(p, env->dst_cpu);
 }
@@ -7997,7 +8250,7 @@
 		case migrate_util:
 			util = task_util_est(p);
 
-			if (util > env->imbalance)
+			if (shr_bound(util, env->sd->nr_balance_failed) > env->imbalance)
 				goto next;
 
 			env->imbalance -= util;
@@ -8009,7 +8262,7 @@
 
 		case migrate_misfit:
 			/* This is not a misfit task */
-			if (task_fits_capacity(p, capacity_of(env->src_cpu)))
+			if (task_fits_cpu(p, env->src_cpu))
 				goto next;
 
 			env->imbalance = 0;
@@ -8040,6 +8293,9 @@
 
 		continue;
 next:
+		if (p->sched_task_hot)
+			schedstat_inc(p->stats.nr_failed_migrations_hot);
+
 		list_move(&p->se.group_node, tasks);
 	}
 
@@ -8395,16 +8651,82 @@
 
 static void update_cpu_capacity(struct sched_domain *sd, int cpu)
 {
+	unsigned long capacity_orig = arch_scale_cpu_capacity(cpu);
 	unsigned long capacity = scale_rt_capacity(cpu);
 	struct sched_group *sdg = sd->groups;
+	struct rq *rq = cpu_rq(cpu);
 
-	cpu_rq(cpu)->cpu_capacity_orig = arch_scale_cpu_capacity(cpu);
+	rq->cpu_capacity_orig = capacity_orig;
 
 	if (!capacity)
 		capacity = 1;
 
-	cpu_rq(cpu)->cpu_capacity = capacity;
-	trace_sched_cpu_capacity_tp(cpu_rq(cpu));
+	rq->cpu_capacity = capacity;
+
+	/*
+	 * Detect if the performance domain is in capacity inversion state.
+	 *
+	 * Capacity inversion happens when another perf domain with equal or
+	 * lower capacity_orig_of() ends up having higher capacity than this
+	 * domain after subtracting thermal pressure.
+	 *
+	 * We only take into account thermal pressure in this detection as it's
+	 * the only metric that actually results in *real* reduction of
+	 * capacity due to performance points (OPPs) being dropped/become
+	 * unreachable due to thermal throttling.
+	 *
+	 * We assume:
+	 *   * That all cpus in a perf domain have the same capacity_orig
+	 *     (same uArch).
+	 *   * Thermal pressure will impact all cpus in this perf domain
+	 *     equally.
+	 */
+	if (sched_energy_enabled()) {
+		unsigned long inv_cap = capacity_orig - thermal_load_avg(rq);
+		struct perf_domain *pd;
+
+		rcu_read_lock();
+
+		pd = rcu_dereference(rq->rd->pd);
+		rq->cpu_capacity_inverted = 0;
+
+		for (; pd; pd = pd->next) {
+			struct cpumask *pd_span = perf_domain_span(pd);
+			unsigned long pd_cap_orig, pd_cap;
+
+			/* We can't be inverted against our own pd */
+			if (cpumask_test_cpu(cpu_of(rq), pd_span))
+				continue;
+
+			cpu = cpumask_any(pd_span);
+			pd_cap_orig = arch_scale_cpu_capacity(cpu);
+
+			if (capacity_orig < pd_cap_orig)
+				continue;
+
+			/*
+			 * handle the case of multiple perf domains have the
+			 * same capacity_orig but one of them is under higher
+			 * thermal pressure. We record it as capacity
+			 * inversion.
+			 */
+			if (capacity_orig == pd_cap_orig) {
+				pd_cap = pd_cap_orig - thermal_load_avg(cpu_rq(cpu));
+
+				if (pd_cap > inv_cap) {
+					rq->cpu_capacity_inverted = inv_cap;
+					break;
+				}
+			} else if (pd_cap_orig > inv_cap) {
+				rq->cpu_capacity_inverted = inv_cap;
+				break;
+			}
+		}
+
+		rcu_read_unlock();
+	}
+
+	trace_sched_cpu_capacity_tp(rq);
 
 	sdg->sgc->capacity = capacity;
 	sdg->sgc->min_capacity = capacity;
@@ -8602,6 +8924,99 @@
 }
 
 /**
+ * asym_smt_can_pull_tasks - Check whether the load balancing CPU can pull tasks
+ * @dst_cpu:	Destination CPU of the load balancing
+ * @sds:	Load-balancing data with statistics of the local group
+ * @sgs:	Load-balancing statistics of the candidate busiest group
+ * @sg:		The candidate busiest group
+ *
+ * Check the state of the SMT siblings of both @sds::local and @sg and decide
+ * if @dst_cpu can pull tasks.
+ *
+ * If @dst_cpu does not have SMT siblings, it can pull tasks if two or more of
+ * the SMT siblings of @sg are busy. If only one CPU in @sg is busy, pull tasks
+ * only if @dst_cpu has higher priority.
+ *
+ * If both @dst_cpu and @sg have SMT siblings, and @sg has exactly one more
+ * busy CPU than @sds::local, let @dst_cpu pull tasks if it has higher priority.
+ * Bigger imbalances in the number of busy CPUs will be dealt with in
+ * update_sd_pick_busiest().
+ *
+ * If @sg does not have SMT siblings, only pull tasks if all of the SMT siblings
+ * of @dst_cpu are idle and @sg has lower priority.
+ */
+static bool asym_smt_can_pull_tasks(int dst_cpu, struct sd_lb_stats *sds,
+				    struct sg_lb_stats *sgs,
+				    struct sched_group *sg)
+{
+#ifdef CONFIG_SCHED_SMT
+	bool local_is_smt, sg_is_smt;
+	int sg_busy_cpus;
+
+	local_is_smt = sds->local->flags & SD_SHARE_CPUCAPACITY;
+	sg_is_smt = sg->flags & SD_SHARE_CPUCAPACITY;
+
+	sg_busy_cpus = sgs->group_weight - sgs->idle_cpus;
+
+	if (!local_is_smt) {
+		/*
+		 * If we are here, @dst_cpu is idle and does not have SMT
+		 * siblings. Pull tasks if candidate group has two or more
+		 * busy CPUs.
+		 */
+		if (sg_busy_cpus >= 2) /* implies sg_is_smt */
+			return true;
+
+		/*
+		 * @dst_cpu does not have SMT siblings. @sg may have SMT
+		 * siblings and only one is busy. In such case, @dst_cpu
+		 * can help if it has higher priority and is idle (i.e.,
+		 * it has no running tasks).
+		 */
+		return sched_asym_prefer(dst_cpu, sg->asym_prefer_cpu);
+	}
+
+	/* @dst_cpu has SMT siblings. */
+
+	if (sg_is_smt) {
+		int local_busy_cpus = sds->local->group_weight -
+				      sds->local_stat.idle_cpus;
+		int busy_cpus_delta = sg_busy_cpus - local_busy_cpus;
+
+		if (busy_cpus_delta == 1)
+			return sched_asym_prefer(dst_cpu, sg->asym_prefer_cpu);
+
+		return false;
+	}
+
+	/*
+	 * @sg does not have SMT siblings. Ensure that @sds::local does not end
+	 * up with more than one busy SMT sibling and only pull tasks if there
+	 * are not busy CPUs (i.e., no CPU has running tasks).
+	 */
+	if (!sds->local_stat.sum_nr_running)
+		return sched_asym_prefer(dst_cpu, sg->asym_prefer_cpu);
+
+	return false;
+#else
+	/* Always return false so that callers deal with non-SMT cases. */
+	return false;
+#endif
+}
+
+static inline bool
+sched_asym(struct lb_env *env, struct sd_lb_stats *sds,  struct sg_lb_stats *sgs,
+	   struct sched_group *group)
+{
+	/* Only do SMT checks if either local or candidate have SMT siblings */
+	if ((sds->local->flags & SD_SHARE_CPUCAPACITY) ||
+	    (group->flags & SD_SHARE_CPUCAPACITY))
+		return asym_smt_can_pull_tasks(env->dst_cpu, sds, sgs, group);
+
+	return sched_asym_prefer(env->dst_cpu, group->asym_prefer_cpu);
+}
+
+/**
  * update_sg_lb_stats - Update sched_group's statistics for load balancing.
  * @env: The load balancing environment.
  * @group: sched_group whose statistics are to be updated.
@@ -8609,6 +9024,7 @@
  * @sg_status: Holds flag indicating the status of the sched_group
  */
 static inline void update_sg_lb_stats(struct lb_env *env,
+				      struct sd_lb_stats *sds,
 				      struct sched_group *group,
 				      struct sg_lb_stats *sgs,
 				      int *sg_status)
@@ -8617,7 +9033,7 @@
 
 	memset(sgs, 0, sizeof(*sgs));
 
-	local_group = cpumask_test_cpu(env->dst_cpu, sched_group_span(group));
+	local_group = group == sds->local;
 
 	for_each_cpu_and(i, sched_group_span(group), env->cpus) {
 		struct rq *rq = cpu_rq(i);
@@ -8660,18 +9076,17 @@
 		}
 	}
 
-	/* Check if dst CPU is idle and preferred to this group */
-	if (env->sd->flags & SD_ASYM_PACKING &&
-	    env->idle != CPU_NOT_IDLE &&
-	    sgs->sum_h_nr_running &&
-	    sched_asym_prefer(env->dst_cpu, group->asym_prefer_cpu)) {
-		sgs->group_asym_packing = 1;
-	}
-
 	sgs->group_capacity = group->sgc->capacity;
 
 	sgs->group_weight = group->group_weight;
 
+	/* Check if dst CPU is idle and preferred to this group */
+	if (!local_group && env->sd->flags & SD_ASYM_PACKING &&
+	    env->idle != CPU_NOT_IDLE && sgs->sum_h_nr_running &&
+	    sched_asym(env, sds, sgs, group)) {
+		sgs->group_asym_packing = 1;
+	}
+
 	sgs->group_type = group_classify(env->sd->imbalance_pct, group, sgs);
 
 	/* Computing avg_load makes sense only when group is overloaded */
@@ -8894,6 +9309,10 @@
 
 	memset(sgs, 0, sizeof(*sgs));
 
+	/* Assume that task can't fit any CPU of the group */
+	if (sd->flags & SD_ASYM_CPUCAPACITY)
+		sgs->group_misfit_task_load = 1;
+
 	for_each_cpu(i, sched_group_span(group)) {
 		struct rq *rq = cpu_rq(i);
 		unsigned int local;
@@ -8913,12 +9332,12 @@
 		if (!nr_running && idle_cpu_without(i, p))
 			sgs->idle_cpus++;
 
-	}
+		/* Check if task fits in the CPU */
+		if (sd->flags & SD_ASYM_CPUCAPACITY &&
+		    sgs->group_misfit_task_load &&
+		    task_fits_cpu(p, i))
+			sgs->group_misfit_task_load = 0;
 
-	/* Check if task fits in the group */
-	if (sd->flags & SD_ASYM_CPUCAPACITY &&
-	    !task_fits_capacity(p, group->sgc->max_capacity)) {
-		sgs->group_misfit_task_load = 1;
 	}
 
 	sgs->group_capacity = group->sgc->capacity;
@@ -8993,9 +9412,10 @@
  * This is an approximation as the number of running tasks may not be
  * related to the number of busy CPUs due to sched_setaffinity.
  */
-static inline bool allow_numa_imbalance(int dst_running, int dst_weight)
+static inline bool
+allow_numa_imbalance(unsigned int running, unsigned int weight)
 {
-	return (dst_running < (dst_weight >> 2));
+	return (running < (weight >> 2));
 }
 
 /*
@@ -9129,12 +9549,13 @@
 				return idlest;
 #endif
 			/*
-			 * Otherwise, keep the task on this node to stay close
-			 * its wakeup source and improve locality. If there is
-			 * a real need of migration, periodic load balance will
-			 * take care of it.
+			 * Otherwise, keep the task close to the wakeup source
+			 * and improve locality if the number of running tasks
+			 * would remain below threshold where an imbalance is
+			 * allowed. If there is a real need of migration,
+			 * periodic load balance will take care of it.
 			 */
-			if (allow_numa_imbalance(local_sgs.sum_nr_running, sd->span_weight))
+			if (allow_numa_imbalance(local_sgs.sum_nr_running + 1, local_sgs.group_weight))
 				return NULL;
 		}
 
@@ -9152,6 +9573,77 @@
 	return idlest;
 }
 
+static void update_idle_cpu_scan(struct lb_env *env,
+				 unsigned long sum_util)
+{
+	struct sched_domain_shared *sd_share;
+	int llc_weight, pct;
+	u64 x, y, tmp;
+	/*
+	 * Update the number of CPUs to scan in LLC domain, which could
+	 * be used as a hint in select_idle_cpu(). The update of sd_share
+	 * could be expensive because it is within a shared cache line.
+	 * So the write of this hint only occurs during periodic load
+	 * balancing, rather than CPU_NEWLY_IDLE, because the latter
+	 * can fire way more frequently than the former.
+	 */
+	if (!sched_feat(SIS_UTIL) || env->idle == CPU_NEWLY_IDLE)
+		return;
+
+	llc_weight = per_cpu(sd_llc_size, env->dst_cpu);
+	if (env->sd->span_weight != llc_weight)
+		return;
+
+	sd_share = rcu_dereference(per_cpu(sd_llc_shared, env->dst_cpu));
+	if (!sd_share)
+		return;
+
+	/*
+	 * The number of CPUs to search drops as sum_util increases, when
+	 * sum_util hits 85% or above, the scan stops.
+	 * The reason to choose 85% as the threshold is because this is the
+	 * imbalance_pct(117) when a LLC sched group is overloaded.
+	 *
+	 * let y = SCHED_CAPACITY_SCALE - p * x^2                       [1]
+	 * and y'= y / SCHED_CAPACITY_SCALE
+	 *
+	 * x is the ratio of sum_util compared to the CPU capacity:
+	 * x = sum_util / (llc_weight * SCHED_CAPACITY_SCALE)
+	 * y' is the ratio of CPUs to be scanned in the LLC domain,
+	 * and the number of CPUs to scan is calculated by:
+	 *
+	 * nr_scan = llc_weight * y'                                    [2]
+	 *
+	 * When x hits the threshold of overloaded, AKA, when
+	 * x = 100 / pct, y drops to 0. According to [1],
+	 * p should be SCHED_CAPACITY_SCALE * pct^2 / 10000
+	 *
+	 * Scale x by SCHED_CAPACITY_SCALE:
+	 * x' = sum_util / llc_weight;                                  [3]
+	 *
+	 * and finally [1] becomes:
+	 * y = SCHED_CAPACITY_SCALE -
+	 *     x'^2 * pct^2 / (10000 * SCHED_CAPACITY_SCALE)            [4]
+	 *
+	 */
+	/* equation [3] */
+	x = sum_util;
+	do_div(x, llc_weight);
+
+	/* equation [4] */
+	pct = env->sd->imbalance_pct;
+	tmp = x * x * pct * pct;
+	do_div(tmp, 10000 * SCHED_CAPACITY_SCALE);
+	tmp = min_t(long, tmp, SCHED_CAPACITY_SCALE);
+	y = SCHED_CAPACITY_SCALE - tmp;
+
+	/* equation [2] */
+	y *= llc_weight;
+	do_div(y, SCHED_CAPACITY_SCALE);
+	if ((int)y != sd_share->nr_idle_scan)
+		WRITE_ONCE(sd_share->nr_idle_scan, (int)y);
+}
+
 /**
  * update_sd_lb_stats - Update sched_domain's statistics for load balancing.
  * @env: The load balancing environment.
@@ -9164,6 +9656,7 @@
 	struct sched_group *sg = env->sd->groups;
 	struct sg_lb_stats *local = &sds->local_stat;
 	struct sg_lb_stats tmp_sgs;
+	unsigned long sum_util = 0;
 	int sg_status = 0;
 
 	do {
@@ -9180,7 +9673,7 @@
 				update_group_capacity(env->sd, env->dst_cpu);
 		}
 
-		update_sg_lb_stats(env, sg, sgs, &sg_status);
+		update_sg_lb_stats(env, sds, sg, sgs, &sg_status);
 
 		if (local_group)
 			goto next_group;
@@ -9196,6 +9689,7 @@
 		sds->total_load += sgs->group_load;
 		sds->total_capacity += sgs->group_capacity;
 
+		sum_util += sgs->group_util;
 		sg = sg->next;
 	} while (sg != env->sd->groups);
 
@@ -9207,20 +9701,17 @@
 		env->fbq_type = fbq_classify_group(&sds->busiest_stat);
 
 	if (!env->sd->parent) {
-		struct root_domain *rd = env->dst_rq->rd;
-
 		/* update overload indicator if we are at root domain */
-		WRITE_ONCE(rd->overload, sg_status & SG_OVERLOAD);
+		WRITE_ONCE(env->dst_rq->rd->overload, sg_status & SG_OVERLOAD);
 
 		/* Update over-utilization (tipping point, U >= 0) indicator */
-		WRITE_ONCE(rd->overutilized, sg_status & SG_OVERUTILIZED);
-		trace_sched_overutilized_tp(rd, sg_status & SG_OVERUTILIZED);
+		set_rd_overutilized_status(env->dst_rq->rd,
+					   sg_status & SG_OVERUTILIZED);
 	} else if (sg_status & SG_OVERUTILIZED) {
-		struct root_domain *rd = env->dst_rq->rd;
-
-		WRITE_ONCE(rd->overutilized, SG_OVERUTILIZED);
-		trace_sched_overutilized_tp(rd, SG_OVERUTILIZED);
+		set_rd_overutilized_status(env->dst_rq->rd, SG_OVERUTILIZED);
 	}
+
+	update_idle_cpu_scan(env, sum_util);
 }
 
 #define NUMA_IMBALANCE_MIN 2
@@ -9340,7 +9831,7 @@
 		/* Consider allowing a small imbalance between NUMA groups */
 		if (env->sd->flags & SD_NUMA) {
 			env->imbalance = adjust_numa_imbalance(env->imbalance,
-				busiest->sum_nr_running, busiest->group_weight);
+				local->sum_nr_running + 1, local->group_weight);
 		}
 
 		return;
@@ -9359,8 +9850,6 @@
 		local->avg_load = (local->group_load * SCHED_CAPACITY_SCALE) /
 				  local->group_capacity;
 
-		sds->avg_load = (sds->total_load * SCHED_CAPACITY_SCALE) /
-				sds->total_capacity;
 		/*
 		 * If the local group is more loaded than the selected
 		 * busiest group don't try to pull any tasks.
@@ -9369,6 +9858,19 @@
 			env->imbalance = 0;
 			return;
 		}
+
+		sds->avg_load = (sds->total_load * SCHED_CAPACITY_SCALE) /
+				sds->total_capacity;
+
+		/*
+		 * If the local group is more loaded than the average system
+		 * load, don't try to pull any tasks.
+		 */
+		if (local->avg_load >= sds->avg_load) {
+			env->imbalance = 0;
+			return;
+		}
+
 	}
 
 	/*
@@ -9603,6 +10105,12 @@
 		    nr_running == 1)
 			continue;
 
+		/* Make sure we only pull tasks from a CPU of lower priority */
+		if ((env->sd->flags & SD_ASYM_PACKING) &&
+		    sched_asym_prefer(i, env->dst_cpu) &&
+		    nr_running == 1)
+			continue;
+
 		switch (env->migration_type) {
 		case migrate_load:
 			/*
@@ -9794,7 +10302,7 @@
 		.sd		= sd,
 		.dst_cpu	= this_cpu,
 		.dst_rq		= this_rq,
-		.dst_grpmask    = sched_group_span(sd->groups),
+		.dst_grpmask    = group_balance_mask(sd->groups),
 		.idle		= idle,
 		.loop_break	= sched_nr_migrate_break,
 		.cpus		= cpus,
@@ -9981,13 +10489,15 @@
 				busiest->push_cpu = this_cpu;
 				active_balance = 1;
 			}
-			raw_spin_rq_unlock_irqrestore(busiest, flags);
 
+			preempt_disable();
+			raw_spin_rq_unlock_irqrestore(busiest, flags);
 			if (active_balance) {
 				stop_one_cpu_nowait(cpu_of(busiest),
 					active_load_balance_cpu_stop, busiest,
 					&busiest->active_balance_work);
 			}
+			preempt_enable();
 		}
 	} else {
 		sd->nr_balance_failed = 0;
@@ -10375,7 +10885,7 @@
 		goto out;
 
 	if (rq->nr_running >= 2) {
-		flags = NOHZ_KICK_MASK;
+		flags = NOHZ_STATS_KICK | NOHZ_BALANCE_KICK;
 		goto out;
 	}
 
@@ -10389,7 +10899,7 @@
 		 * on.
 		 */
 		if (rq->cfs.h_nr_running >= 1 && check_cpu_capacity(rq, sd)) {
-			flags = NOHZ_KICK_MASK;
+			flags = NOHZ_STATS_KICK | NOHZ_BALANCE_KICK;
 			goto unlock;
 		}
 	}
@@ -10403,7 +10913,7 @@
 		 */
 		for_each_cpu_and(i, sched_domain_span(sd), nohz.idle_cpus_mask) {
 			if (sched_asym_prefer(i, cpu)) {
-				flags = NOHZ_KICK_MASK;
+				flags = NOHZ_STATS_KICK | NOHZ_BALANCE_KICK;
 				goto unlock;
 			}
 		}
@@ -10416,7 +10926,7 @@
 		 * to run the misfit task on.
 		 */
 		if (check_misfit_status(rq, sd)) {
-			flags = NOHZ_KICK_MASK;
+			flags = NOHZ_STATS_KICK | NOHZ_BALANCE_KICK;
 			goto unlock;
 		}
 
@@ -10443,7 +10953,7 @@
 		 */
 		nr_busy = atomic_read(&sds->nr_busy_cpus);
 		if (nr_busy > 1) {
-			flags = NOHZ_KICK_MASK;
+			flags = NOHZ_STATS_KICK | NOHZ_BALANCE_KICK;
 			goto unlock;
 		}
 	}
@@ -10605,7 +11115,8 @@
 	 * setting the flag, we are sure to not clear the state and not
 	 * check the load of an idle cpu.
 	 */
-	WRITE_ONCE(nohz.has_blocked, 0);
+	if (flags & NOHZ_STATS_KICK)
+		WRITE_ONCE(nohz.has_blocked, 0);
 
 	/*
 	 * Ensures that if we miss the CPU, we must see the has_blocked
@@ -10626,14 +11137,16 @@
 		 * work being done for other CPUs. Next load
 		 * balancing owner will pick it up.
 		 */
-		if (need_resched()) {
-			has_blocked_load = true;
+		if (!idle_cpu(this_cpu) && need_resched()) {
+			if (flags & NOHZ_STATS_KICK)
+				has_blocked_load = true;
 			goto abort;
 		}
 
 		rq = cpu_rq(balance_cpu);
 
-		has_blocked_load |= update_nohz_stats(rq);
+		if (flags & NOHZ_STATS_KICK)
+			has_blocked_load |= update_nohz_stats(rq);
 
 		/*
 		 * If time for next balance is due,
@@ -10664,8 +11177,9 @@
 	if (likely(update_next_balance))
 		nohz.next_balance = next_balance;
 
-	WRITE_ONCE(nohz.next_blocked,
-		now + msecs_to_jiffies(LOAD_AVG_PERIOD));
+	if (flags & NOHZ_STATS_KICK)
+		WRITE_ONCE(nohz.next_blocked,
+			   now + msecs_to_jiffies(LOAD_AVG_PERIOD));
 
 abort:
 	/* There is still blocked load, enable periodic update */
@@ -11075,7 +11589,7 @@
 		task_tick_numa(rq, curr);
 
 	update_misfit_status(curr, rq);
-	update_overutilized_status(task_rq(curr));
+	check_update_overutilized_status(task_rq(curr));
 
 	task_tick_core(rq, curr);
 }
@@ -11358,8 +11872,6 @@
 {
 	int i;
 
-	destroy_cfs_bandwidth(tg_cfs_bandwidth(tg));
-
 	for_each_possible_cpu(i) {
 		if (tg->cfs_rq)
 			kfree(tg->cfs_rq[i]);
@@ -11394,7 +11906,7 @@
 		if (!cfs_rq)
 			goto err;
 
-		se = kzalloc_node(sizeof(struct sched_entity),
+		se = kzalloc_node(sizeof(struct sched_entity_stats),
 				  GFP_KERNEL, cpu_to_node(i));
 		if (!se)
 			goto err_free_rq;
@@ -11436,6 +11948,8 @@
 	struct rq *rq;
 	int cpu;
 
+	destroy_cfs_bandwidth(tg_cfs_bandwidth(tg));
+
 	for_each_possible_cpu(cpu) {
 		if (tg->se[cpu])
 			remove_entity_load_avg(tg->se[cpu]);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/features.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/features.h
@@ -55,7 +55,8 @@
 /*
  * When doing wakeups, attempt to limit superfluous scans of the LLC domain.
  */
-SCHED_FEAT(SIS_PROP, true)
+SCHED_FEAT(SIS_PROP, false)
+SCHED_FEAT(SIS_UTIL, true)
 
 /*
  * Issue a WARN when we do multiple update_rq_clock() calls
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/idle.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/idle.c
@@ -105,7 +105,7 @@
 		 * last -- this is very similar to the entry code.
 		 */
 		trace_hardirqs_on_prepare();
-		lockdep_hardirqs_on_prepare(_THIS_IP_);
+		lockdep_hardirqs_on_prepare();
 		rcu_idle_enter();
 		lockdep_hardirqs_on(_THIS_IP_);
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/membarrier.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/membarrier.c
@@ -147,11 +147,11 @@
 #endif
 
 #ifdef CONFIG_RSEQ
-#define MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK		\
+#define MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK		\
 	(MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ			\
-	| MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ_BITMASK)
+	| MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ)
 #else
-#define MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK	0
+#define MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK	0
 #endif
 
 #define MEMBARRIER_CMD_BITMASK						\
@@ -159,7 +159,10 @@
 	| MEMBARRIER_CMD_REGISTER_GLOBAL_EXPEDITED			\
 	| MEMBARRIER_CMD_PRIVATE_EXPEDITED				\
 	| MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED			\
-	| MEMBARRIER_PRIVATE_EXPEDITED_SYNC_CORE_BITMASK)
+	| MEMBARRIER_PRIVATE_EXPEDITED_SYNC_CORE_BITMASK		\
+	| MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK)
+
+static DEFINE_MUTEX(membarrier_ipi_mutex);
 
 static void ipi_mb(void *info)
 {
@@ -258,6 +261,7 @@
 	if (!zalloc_cpumask_var(&tmpmask, GFP_KERNEL))
 		return -ENOMEM;
 
+	mutex_lock(&membarrier_ipi_mutex);
 	cpus_read_lock();
 	rcu_read_lock();
 	for_each_online_cpu(cpu) {
@@ -303,6 +307,8 @@
 	 * rq->curr modification in scheduler.
 	 */
 	smp_mb();	/* exit from system call is not a mb */
+	mutex_unlock(&membarrier_ipi_mutex);
+
 	return 0;
 }
 
@@ -346,6 +352,7 @@
 	if (cpu_id < 0 && !zalloc_cpumask_var(&tmpmask, GFP_KERNEL))
 		return -ENOMEM;
 
+	mutex_lock(&membarrier_ipi_mutex);
 	cpus_read_lock();
 
 	if (cpu_id >= 0) {
@@ -418,6 +425,7 @@
 	 * rq->curr modification in scheduler.
 	 */
 	smp_mb();	/* exit from system call is not a mb */
+	mutex_unlock(&membarrier_ipi_mutex);
 
 	return 0;
 }
@@ -459,6 +467,7 @@
 	 * between threads which are users of @mm has its membarrier state
 	 * updated.
 	 */
+	mutex_lock(&membarrier_ipi_mutex);
 	cpus_read_lock();
 	rcu_read_lock();
 	for_each_online_cpu(cpu) {
@@ -475,6 +484,7 @@
 
 	free_cpumask_var(tmpmask);
 	cpus_read_unlock();
+	mutex_unlock(&membarrier_ipi_mutex);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/pelt.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/pelt.h
@@ -37,9 +37,11 @@
 }
 #endif
 
+#define PELT_MIN_DIVIDER	(LOAD_AVG_MAX - 1024)
+
 static inline u32 get_pelt_divider(struct sched_avg *avg)
 {
-	return LOAD_AVG_MAX - 1024 + avg->period_contrib;
+	return PELT_MIN_DIVIDER + avg->period_contrib;
 }
 
 static inline void cfs_se_util_change(struct sched_avg *avg)
@@ -143,9 +145,9 @@
 static inline u64 cfs_rq_clock_pelt(struct cfs_rq *cfs_rq)
 {
 	if (unlikely(cfs_rq->throttle_count))
-		return cfs_rq->throttled_clock_task - cfs_rq->throttled_clock_task_time;
+		return cfs_rq->throttled_clock_pelt - cfs_rq->throttled_clock_pelt_time;
 
-	return rq_clock_pelt(rq_of(cfs_rq)) - cfs_rq->throttled_clock_task_time;
+	return rq_clock_pelt(rq_of(cfs_rq)) - cfs_rq->throttled_clock_pelt_time;
 }
 #else
 static inline u64 cfs_rq_clock_pelt(struct cfs_rq *cfs_rq)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/psi.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/psi.c
@@ -34,13 +34,19 @@
  * delayed on that resource such that nobody is advancing and the CPU
  * goes idle. This leaves both workload and CPU unproductive.
  *
- * Naturally, the FULL state doesn't exist for the CPU resource at the
- * system level, but exist at the cgroup level, means all non-idle tasks
- * in a cgroup are delayed on the CPU resource which used by others outside
- * of the cgroup or throttled by the cgroup cpu.max configuration.
- *
  *	SOME = nr_delayed_tasks != 0
- *	FULL = nr_delayed_tasks != 0 && nr_running_tasks == 0
+ *	FULL = nr_delayed_tasks != 0 && nr_productive_tasks == 0
+ *
+ * What it means for a task to be productive is defined differently
+ * for each resource. For IO, productive means a running task. For
+ * memory, productive means a running task that isn't a reclaimer. For
+ * CPU, productive means an oncpu task.
+ *
+ * Naturally, the FULL state doesn't exist for the CPU resource at the
+ * system level, but exist at the cgroup level. At the cgroup level,
+ * FULL means all non-idle tasks in the cgroup are delayed on the CPU
+ * resource which is being used by others outside of the cgroup or
+ * throttled by the cgroup cpu.max configuration.
  *
  * The percentage of wallclock time spent in those compound stall
  * states gives pressure numbers between 0 and 100 for each resource,
@@ -81,13 +87,13 @@
  *
  *	threads = min(nr_nonidle_tasks, nr_cpus)
  *	   SOME = min(nr_delayed_tasks / threads, 1)
- *	   FULL = (threads - min(nr_running_tasks, threads)) / threads
+ *	   FULL = (threads - min(nr_productive_tasks, threads)) / threads
  *
  * For the 257 number crunchers on 256 CPUs, this yields:
  *
  *	threads = min(257, 256)
  *	   SOME = min(1 / 256, 1)             = 0.4%
- *	   FULL = (256 - min(257, 256)) / 256 = 0%
+ *	   FULL = (256 - min(256, 256)) / 256 = 0%
  *
  * For the 1 out of 4 memory-delayed tasks, this yields:
  *
@@ -112,7 +118,7 @@
  * For each runqueue, we track:
  *
  *	   tSOME[cpu] = time(nr_delayed_tasks[cpu] != 0)
- *	   tFULL[cpu] = time(nr_delayed_tasks[cpu] && !nr_running_tasks[cpu])
+ *	   tFULL[cpu] = time(nr_delayed_tasks[cpu] && !nr_productive_tasks[cpu])
  *	tNONIDLE[cpu] = time(nr_nonidle_tasks[cpu] != 0)
  *
  * and then periodically aggregate:
@@ -233,7 +239,8 @@
 	case PSI_MEM_SOME:
 		return unlikely(tasks[NR_MEMSTALL]);
 	case PSI_MEM_FULL:
-		return unlikely(tasks[NR_MEMSTALL] && !tasks[NR_RUNNING]);
+		return unlikely(tasks[NR_MEMSTALL] &&
+			tasks[NR_RUNNING] == tasks[NR_MEMSTALL_RUNNING]);
 	case PSI_CPU_SOME:
 		return unlikely(tasks[NR_RUNNING] > tasks[NR_ONCPU]);
 	case PSI_CPU_FULL:
@@ -710,10 +717,11 @@
 		if (groupc->tasks[t]) {
 			groupc->tasks[t]--;
 		} else if (!psi_bug) {
-			printk_deferred(KERN_ERR "psi: task underflow! cpu=%d t=%d tasks=[%u %u %u %u] clear=%x set=%x\n",
+			printk_deferred(KERN_ERR "psi: task underflow! cpu=%d t=%d tasks=[%u %u %u %u %u] clear=%x set=%x\n",
 					cpu, t, groupc->tasks[0],
 					groupc->tasks[1], groupc->tasks[2],
-					groupc->tasks[3], clear, set);
+					groupc->tasks[3], groupc->tasks[4],
+					clear, set);
 			psi_bug = 1;
 		}
 	}
@@ -854,12 +862,15 @@
 		int clear = TSK_ONCPU, set = 0;
 
 		/*
-		 * When we're going to sleep, psi_dequeue() lets us handle
-		 * TSK_RUNNING and TSK_IOWAIT here, where we can combine it
-		 * with TSK_ONCPU and save walking common ancestors twice.
+		 * When we're going to sleep, psi_dequeue() lets us
+		 * handle TSK_RUNNING, TSK_MEMSTALL_RUNNING and
+		 * TSK_IOWAIT here, where we can combine it with
+		 * TSK_ONCPU and save walking common ancestors twice.
 		 */
 		if (sleep) {
 			clear |= TSK_RUNNING;
+			if (prev->in_memstall)
+				clear |= TSK_MEMSTALL_RUNNING;
 			if (prev->in_iowait)
 				set |= TSK_IOWAIT;
 		}
@@ -908,7 +919,7 @@
 	rq = this_rq_lock_irq(&rf);
 
 	current->in_memstall = 1;
-	psi_task_change(current, 0, TSK_MEMSTALL);
+	psi_task_change(current, 0, TSK_MEMSTALL | TSK_MEMSTALL_RUNNING);
 
 	rq_unlock_irq(rq, &rf);
 }
@@ -937,7 +948,7 @@
 	rq = this_rq_lock_irq(&rf);
 
 	current->in_memstall = 0;
-	psi_task_change(current, TSK_MEMSTALL, 0);
+	psi_task_change(current, TSK_MEMSTALL | TSK_MEMSTALL_RUNNING, 0);
 
 	rq_unlock_irq(rq, &rf);
 }
@@ -1051,14 +1062,17 @@
 	mutex_unlock(&group->avgs_lock);
 
 	for (full = 0; full < 2; full++) {
-		unsigned long avg[3];
-		u64 total;
+		unsigned long avg[3] = { 0, };
+		u64 total = 0;
 		int w;
 
-		for (w = 0; w < 3; w++)
-			avg[w] = group->avg[res * 2 + full][w];
-		total = div_u64(group->total[PSI_AVGS][res * 2 + full],
-				NSEC_PER_USEC);
+		/* CPU FULL is undefined at the system level */
+		if (!(group == &psi_system && res == PSI_CPU && full)) {
+			for (w = 0; w < 3; w++)
+				avg[w] = group->avg[res * 2 + full][w];
+			total = div_u64(group->total[PSI_AVGS][res * 2 + full],
+					NSEC_PER_USEC);
+		}
 
 		seq_printf(m, "%s avg10=%lu.%02lu avg60=%lu.%02lu avg300=%lu.%02lu total=%llu\n",
 			   full ? "full" : "some",
@@ -1071,44 +1085,6 @@
 	return 0;
 }
 
-static int psi_io_show(struct seq_file *m, void *v)
-{
-	return psi_show(m, &psi_system, PSI_IO);
-}
-
-static int psi_memory_show(struct seq_file *m, void *v)
-{
-	return psi_show(m, &psi_system, PSI_MEM);
-}
-
-static int psi_cpu_show(struct seq_file *m, void *v)
-{
-	return psi_show(m, &psi_system, PSI_CPU);
-}
-
-static int psi_open(struct file *file, int (*psi_show)(struct seq_file *, void *))
-{
-	if (file->f_mode & FMODE_WRITE && !capable(CAP_SYS_RESOURCE))
-		return -EPERM;
-
-	return single_open(file, psi_show, NULL);
-}
-
-static int psi_io_open(struct inode *inode, struct file *file)
-{
-	return psi_open(file, psi_io_show);
-}
-
-static int psi_memory_open(struct inode *inode, struct file *file)
-{
-	return psi_open(file, psi_memory_show);
-}
-
-static int psi_cpu_open(struct inode *inode, struct file *file)
-{
-	return psi_open(file, psi_cpu_show);
-}
-
 struct psi_trigger *psi_trigger_create(struct psi_group *group,
 			char *buf, size_t nbytes, enum psi_res res)
 {
@@ -1151,7 +1127,6 @@
 	t->event = 0;
 	t->last_event_time = 0;
 	init_waitqueue_head(&t->event_wait);
-	kref_init(&t->refcount);
 
 	mutex_lock(&group->trigger_lock);
 
@@ -1180,20 +1155,25 @@
 	return t;
 }
 
-static void psi_trigger_destroy(struct kref *ref)
+void psi_trigger_destroy(struct psi_trigger *t)
 {
-	struct psi_trigger *t = container_of(ref, struct psi_trigger, refcount);
-	struct psi_group *group = t->group;
+	struct psi_group *group;
 	struct task_struct *task_to_destroy = NULL;
 
-	if (static_branch_likely(&psi_disabled))
+	/*
+	 * We do not check psi_disabled since it might have been disabled after
+	 * the trigger got created.
+	 */
+	if (!t)
 		return;
 
+	group = t->group;
 	/*
-	 * Wakeup waiters to stop polling. Can happen if cgroup is deleted
-	 * from under a polling process.
+	 * Wakeup waiters to stop polling and clear the queue to prevent it from
+	 * being accessed later. Can happen if cgroup is deleted from under a
+	 * polling process.
 	 */
-	wake_up_interruptible(&t->event_wait);
+	wake_up_pollfree(&t->event_wait);
 
 	mutex_lock(&group->trigger_lock);
 
@@ -1224,9 +1204,9 @@
 	mutex_unlock(&group->trigger_lock);
 
 	/*
-	 * Wait for both *trigger_ptr from psi_trigger_replace and
-	 * poll_task RCUs to complete their read-side critical sections
-	 * before destroying the trigger and optionally the poll_task
+	 * Wait for psi_schedule_poll_work RCU to complete its read-side
+	 * critical section before destroying the trigger and optionally the
+	 * poll_task.
 	 */
 	synchronize_rcu();
 	/*
@@ -1243,18 +1223,6 @@
 	kfree(t);
 }
 
-void psi_trigger_replace(void **trigger_ptr, struct psi_trigger *new)
-{
-	struct psi_trigger *old = *trigger_ptr;
-
-	if (static_branch_likely(&psi_disabled))
-		return;
-
-	rcu_assign_pointer(*trigger_ptr, new);
-	if (old)
-		kref_put(&old->refcount, psi_trigger_destroy);
-}
-
 __poll_t psi_trigger_poll(void **trigger_ptr,
 				struct file *file, poll_table *wait)
 {
@@ -1264,27 +1232,57 @@
 	if (static_branch_likely(&psi_disabled))
 		return DEFAULT_POLLMASK | EPOLLERR | EPOLLPRI;
 
-	rcu_read_lock();
-
-	t = rcu_dereference(*(void __rcu __force **)trigger_ptr);
-	if (!t) {
-		rcu_read_unlock();
+	t = smp_load_acquire(trigger_ptr);
+	if (!t)
 		return DEFAULT_POLLMASK | EPOLLERR | EPOLLPRI;
-	}
-	kref_get(&t->refcount);
-
-	rcu_read_unlock();
 
 	poll_wait(file, &t->event_wait, wait);
 
 	if (cmpxchg(&t->event, 1, 0) == 1)
 		ret |= EPOLLPRI;
 
-	kref_put(&t->refcount, psi_trigger_destroy);
-
 	return ret;
 }
 
+#ifdef CONFIG_PROC_FS
+static int psi_io_show(struct seq_file *m, void *v)
+{
+	return psi_show(m, &psi_system, PSI_IO);
+}
+
+static int psi_memory_show(struct seq_file *m, void *v)
+{
+	return psi_show(m, &psi_system, PSI_MEM);
+}
+
+static int psi_cpu_show(struct seq_file *m, void *v)
+{
+	return psi_show(m, &psi_system, PSI_CPU);
+}
+
+static int psi_open(struct file *file, int (*psi_show)(struct seq_file *, void *))
+{
+	if (file->f_mode & FMODE_WRITE && !capable(CAP_SYS_RESOURCE))
+		return -EPERM;
+
+	return single_open(file, psi_show, NULL);
+}
+
+static int psi_io_open(struct inode *inode, struct file *file)
+{
+	return psi_open(file, psi_io_show);
+}
+
+static int psi_memory_open(struct inode *inode, struct file *file)
+{
+	return psi_open(file, psi_memory_show);
+}
+
+static int psi_cpu_open(struct inode *inode, struct file *file)
+{
+	return psi_open(file, psi_cpu_show);
+}
+
 static ssize_t psi_write(struct file *file, const char __user *user_buf,
 			 size_t nbytes, enum psi_res res)
 {
@@ -1305,14 +1303,24 @@
 
 	buf[buf_size - 1] = '\0';
 
-	new = psi_trigger_create(&psi_system, buf, nbytes, res);
-	if (IS_ERR(new))
-		return PTR_ERR(new);
-
 	seq = file->private_data;
+
 	/* Take seq->lock to protect seq->private from concurrent writes */
 	mutex_lock(&seq->lock);
-	psi_trigger_replace(&seq->private, new);
+
+	/* Allow only one trigger per file descriptor */
+	if (seq->private) {
+		mutex_unlock(&seq->lock);
+		return -EBUSY;
+	}
+
+	new = psi_trigger_create(&psi_system, buf, nbytes, res);
+	if (IS_ERR(new)) {
+		mutex_unlock(&seq->lock);
+		return PTR_ERR(new);
+	}
+
+	smp_store_release(&seq->private, new);
 	mutex_unlock(&seq->lock);
 
 	return nbytes;
@@ -1347,7 +1355,7 @@
 {
 	struct seq_file *seq = file->private_data;
 
-	psi_trigger_replace(&seq->private, NULL);
+	psi_trigger_destroy(seq->private);
 	return single_release(inode, file);
 }
 
@@ -1389,3 +1397,5 @@
 	return 0;
 }
 module_init(psi_proc_init);
+
+#endif /* CONFIG_PROC_FS */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/rt.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/rt.c
@@ -8,7 +8,7 @@
 #include "pelt.h"
 
 int sched_rr_timeslice = RR_TIMESLICE;
-int sysctl_sched_rr_timeslice = (MSEC_PER_SEC / HZ) * RR_TIMESLICE;
+int sysctl_sched_rr_timeslice = (MSEC_PER_SEC * RR_TIMESLICE) / HZ;
 /* More than 4 hours if BW_SHIFT equals 20. */
 static const u64 max_rt_runtime = MAX_BW;
 
@@ -52,11 +52,8 @@
 	rt_b->rt_period_timer.function = sched_rt_period_timer;
 }
 
-static void start_rt_bandwidth(struct rt_bandwidth *rt_b)
+static inline void do_start_rt_bandwidth(struct rt_bandwidth *rt_b)
 {
-	if (!rt_bandwidth_enabled() || rt_b->rt_runtime == RUNTIME_INF)
-		return;
-
 	raw_spin_lock(&rt_b->rt_runtime_lock);
 	if (!rt_b->rt_period_active) {
 		rt_b->rt_period_active = 1;
@@ -75,6 +72,14 @@
 	raw_spin_unlock(&rt_b->rt_runtime_lock);
 }
 
+static void start_rt_bandwidth(struct rt_bandwidth *rt_b)
+{
+	if (!rt_bandwidth_enabled() || rt_b->rt_runtime == RUNTIME_INF)
+		return;
+
+	do_start_rt_bandwidth(rt_b);
+}
+
 void init_rt_rq(struct rt_rq *rt_rq)
 {
 	struct rt_prio_array *array;
@@ -137,13 +142,17 @@
 	return rt_rq->rq;
 }
 
-void free_rt_sched_group(struct task_group *tg)
+void unregister_rt_sched_group(struct task_group *tg)
 {
-	int i;
-
 	if (tg->rt_se)
 		destroy_rt_bandwidth(&tg->rt_bandwidth);
 
+}
+
+void free_rt_sched_group(struct task_group *tg)
+{
+	int i;
+
 	for_each_possible_cpu(i) {
 		if (tg->rt_rq)
 			kfree(tg->rt_rq[i]);
@@ -250,6 +259,8 @@
 	return &rq->rt;
 }
 
+void unregister_rt_sched_group(struct task_group *tg) { }
+
 void free_rt_sched_group(struct task_group *tg) { }
 
 int alloc_rt_sched_group(struct task_group *tg, struct task_group *parent)
@@ -433,7 +444,7 @@
 #endif /* CONFIG_SMP */
 
 static void enqueue_top_rt_rq(struct rt_rq *rt_rq);
-static void dequeue_top_rt_rq(struct rt_rq *rt_rq);
+static void dequeue_top_rt_rq(struct rt_rq *rt_rq, unsigned int count);
 
 static inline int on_rt_rq(struct sched_rt_entity *rt_se)
 {
@@ -462,7 +473,7 @@
 	unsigned int cpu_cap;
 
 	/* Only heterogeneous systems can benefit from this check */
-	if (!static_branch_unlikely(&sched_asym_cpucapacity))
+	if (!sched_asym_cpucap_active())
 		return true;
 
 	min_cap = uclamp_eff_value(p, UCLAMP_MIN);
@@ -554,7 +565,7 @@
 	rt_se = rt_rq->tg->rt_se[cpu];
 
 	if (!rt_se) {
-		dequeue_top_rt_rq(rt_rq);
+		dequeue_top_rt_rq(rt_rq, rt_rq->rt_nr_running);
 		/* Kick cpufreq (see the comment in kernel/sched/sched.h). */
 		cpufreq_update_util(rq_of_rt_rq(rt_rq), 0);
 	}
@@ -640,7 +651,7 @@
 
 static inline void sched_rt_rq_dequeue(struct rt_rq *rt_rq)
 {
-	dequeue_top_rt_rq(rt_rq);
+	dequeue_top_rt_rq(rt_rq, rt_rq->rt_nr_running);
 }
 
 static inline int rt_rq_throttled(struct rt_rq *rt_rq)
@@ -874,6 +885,7 @@
 		int enqueue = 0;
 		struct rt_rq *rt_rq = sched_rt_period_rt_rq(rt_b, i);
 		struct rq *rq = rq_of_rt_rq(rt_rq);
+		struct rq_flags rf;
 		int skip;
 
 		/*
@@ -888,7 +900,7 @@
 		if (skip)
 			continue;
 
-		raw_spin_rq_lock(rq);
+		rq_lock(rq, &rf);
 		update_rq_clock(rq);
 
 		if (rt_rq->rt_time) {
@@ -926,7 +938,7 @@
 
 		if (enqueue)
 			sched_rt_rq_enqueue(rt_rq);
-		raw_spin_rq_unlock(rq);
+		rq_unlock(rq, &rf);
 	}
 
 	if (!throttled && (!rt_bandwidth_enabled() || rt_b->rt_runtime == RUNTIME_INF))
@@ -1009,8 +1021,8 @@
 	if (unlikely((s64)delta_exec <= 0))
 		return;
 
-	schedstat_set(curr->se.statistics.exec_max,
-		      max(curr->se.statistics.exec_max, delta_exec));
+	schedstat_set(curr->stats.exec_max,
+		      max(curr->stats.exec_max, delta_exec));
 
 	curr->se.sum_exec_runtime += delta_exec;
 	account_group_exec_runtime(curr, delta_exec);
@@ -1023,19 +1035,23 @@
 
 	for_each_sched_rt_entity(rt_se) {
 		struct rt_rq *rt_rq = rt_rq_of_se(rt_se);
+		int exceeded;
 
 		if (sched_rt_runtime(rt_rq) != RUNTIME_INF) {
 			raw_spin_lock(&rt_rq->rt_runtime_lock);
 			rt_rq->rt_time += delta_exec;
-			if (sched_rt_runtime_exceeded(rt_rq))
+			exceeded = sched_rt_runtime_exceeded(rt_rq);
+			if (exceeded)
 				resched_curr(rq);
 			raw_spin_unlock(&rt_rq->rt_runtime_lock);
+			if (exceeded)
+				do_start_rt_bandwidth(sched_rt_bandwidth(rt_rq));
 		}
 	}
 }
 
 static void
-dequeue_top_rt_rq(struct rt_rq *rt_rq)
+dequeue_top_rt_rq(struct rt_rq *rt_rq, unsigned int count)
 {
 	struct rq *rq = rq_of_rt_rq(rt_rq);
 
@@ -1046,7 +1062,7 @@
 
 	BUG_ON(!rq->nr_running);
 
-	sub_nr_running(rq, rt_rq->rt_nr_running);
+	sub_nr_running(rq, count);
 	rt_rq->rt_queued = 0;
 
 }
@@ -1326,18 +1342,21 @@
 static void dequeue_rt_stack(struct sched_rt_entity *rt_se, unsigned int flags)
 {
 	struct sched_rt_entity *back = NULL;
+	unsigned int rt_nr_running;
 
 	for_each_sched_rt_entity(rt_se) {
 		rt_se->back = back;
 		back = rt_se;
 	}
 
-	dequeue_top_rt_rq(rt_rq_of_se(back));
+	rt_nr_running = rt_rq_of_se(back)->rt_nr_running;
 
 	for (rt_se = back; rt_se; rt_se = rt_se->back) {
 		if (on_rt_rq(rt_se))
 			__dequeue_rt_entity(rt_se, flags);
 	}
+
+	dequeue_top_rt_rq(rt_rq_of_se(back), rt_nr_running);
 }
 
 static void enqueue_rt_entity(struct sched_rt_entity *rt_se, unsigned int flags)
@@ -1595,8 +1614,7 @@
 	rt_queue_push_tasks(rq);
 }
 
-static struct sched_rt_entity *pick_next_rt_entity(struct rq *rq,
-						   struct rt_rq *rt_rq)
+static struct sched_rt_entity *pick_next_rt_entity(struct rt_rq *rt_rq)
 {
 	struct rt_prio_array *array = &rt_rq->active;
 	struct sched_rt_entity *next = NULL;
@@ -1607,6 +1625,8 @@
 	BUG_ON(idx >= MAX_RT_PRIO);
 
 	queue = array->queue + idx;
+	if (SCHED_WARN_ON(list_empty(queue)))
+		return NULL;
 	next = list_entry(queue->next, struct sched_rt_entity, run_list);
 
 	return next;
@@ -1618,8 +1638,9 @@
 	struct rt_rq *rt_rq  = &rq->rt;
 
 	do {
-		rt_se = pick_next_rt_entity(rq, rt_rq);
-		BUG_ON(!rt_se);
+		rt_se = pick_next_rt_entity(rt_rq);
+		if (unlikely(!rt_se))
+			return NULL;
 		rt_rq = group_rt_rq(rt_se);
 	} while (rt_rq);
 
@@ -1717,7 +1738,7 @@
 	 * If we're on asym system ensure we consider the different capacities
 	 * of the CPUs when searching for the lowest_mask.
 	 */
-	if (static_branch_unlikely(&sched_asym_cpucapacity)) {
+	if (sched_asym_cpucap_active()) {
 
 		ret = cpupri_find_fitness(&task_rq(task)->rd->cpupri,
 					  task, lowest_mask,
@@ -1821,11 +1842,15 @@
 			 * the mean time, task could have
 			 * migrated already or had its affinity changed.
 			 * Also make sure that it wasn't scheduled on its rq.
+			 * It is possible the task was scheduled, set
+			 * "migrate_disabled" and then got preempted, so we must
+			 * check the task migration disable flag here too.
 			 */
 			if (unlikely(task_rq(task) != rq ||
 				     !cpumask_test_cpu(lowest_rq->cpu, &task->cpus_mask) ||
 				     task_running(rq, task) ||
 				     !rt_task(task) ||
+				     is_migration_disabled(task) ||
 				     !task_on_rq_queued(task))) {
 
 				double_unlock_balance(rq, lowest_rq);
@@ -1885,6 +1910,16 @@
 		return 0;
 
 retry:
+	/*
+	 * It's possible that the next_task slipped in of
+	 * higher priority than current. If that's the case
+	 * just reschedule current.
+	 */
+	if (unlikely(next_task->prio < rq->curr->prio)) {
+		resched_curr(rq);
+		return 0;
+	}
+
 	if (is_migration_disabled(next_task)) {
 		struct task_struct *push_task = NULL;
 		int cpu;
@@ -1892,6 +1927,18 @@
 		if (!pull || rq->push_busy)
 			return 0;
 
+		/*
+		 * Invoking find_lowest_rq() on anything but an RT task doesn't
+		 * make sense. Per the above priority check, curr has to
+		 * be of higher priority than next_task, so no need to
+		 * reschedule when bailing out.
+		 *
+		 * Note that the stoppers are masqueraded as SCHED_FIFO
+		 * (cf. sched_set_stop_task()), so we can't rely on rt_task().
+		 */
+		if (rq->curr->sched_class != &rt_sched_class)
+			return 0;
+
 		cpu = find_lowest_rq(rq->curr);
 		if (cpu == -1 || cpu == rq->cpu)
 			return 0;
@@ -1904,9 +1951,11 @@
 		 */
 		push_task = get_push_task(rq);
 		if (push_task) {
+			preempt_disable();
 			raw_spin_rq_unlock(rq);
 			stop_one_cpu_nowait(rq->cpu, push_cpu_stop,
 					    push_task, &rq->push_work);
+			preempt_enable();
 			raw_spin_rq_lock(rq);
 		}
 
@@ -1916,16 +1965,6 @@
 	if (WARN_ON(next_task == rq->curr))
 		return 0;
 
-	/*
-	 * It's possible that the next_task slipped in of
-	 * higher priority than current. If that's the case
-	 * just reschedule current.
-	 */
-	if (unlikely(next_task->prio < rq->curr->prio)) {
-		resched_curr(rq);
-		return 0;
-	}
-
 	/* We might release rq lock */
 	get_task_struct(next_task);
 
@@ -2253,9 +2292,11 @@
 		double_unlock_balance(this_rq, src_rq);
 
 		if (push_task) {
+			preempt_disable();
 			raw_spin_rq_unlock(this_rq);
 			stop_one_cpu_nowait(src_rq->cpu, push_cpu_stop,
 					    push_task, &src_rq->push_work);
+			preempt_enable();
 			raw_spin_rq_lock(this_rq);
 		}
 	}
@@ -2765,9 +2806,6 @@
 
 static int sched_rt_global_validate(void)
 {
-	if (sysctl_sched_rt_period <= 0)
-		return -EINVAL;
-
 	if ((sysctl_sched_rt_runtime != RUNTIME_INF) &&
 		((sysctl_sched_rt_runtime > sysctl_sched_rt_period) ||
 		 ((u64)sysctl_sched_rt_runtime *
@@ -2779,8 +2817,12 @@
 
 static void sched_rt_do_global(void)
 {
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&def_rt_bandwidth.rt_runtime_lock, flags);
 	def_rt_bandwidth.rt_runtime = global_rt_runtime();
 	def_rt_bandwidth.rt_period = ns_to_ktime(global_rt_period());
+	raw_spin_unlock_irqrestore(&def_rt_bandwidth.rt_runtime_lock, flags);
 }
 
 int sched_rt_handler(struct ctl_table *table, int write, void *buffer,
@@ -2794,7 +2836,7 @@
 	old_period = sysctl_sched_rt_period;
 	old_runtime = sysctl_sched_rt_runtime;
 
-	ret = proc_dointvec(table, write, buffer, lenp, ppos);
+	ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
 
 	if (!ret && write) {
 		ret = sched_rt_global_validate();
@@ -2838,6 +2880,9 @@
 		sched_rr_timeslice =
 			sysctl_sched_rr_timeslice <= 0 ? RR_TIMESLICE :
 			msecs_to_jiffies(sysctl_sched_rr_timeslice);
+
+		if (sysctl_sched_rr_timeslice <= 0)
+			sysctl_sched_rr_timeslice = jiffies_to_msecs(RR_TIMESLICE);
 	}
 	mutex_unlock(&mutex);
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/sched.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/sched.h
@@ -348,9 +348,8 @@
 extern void __getparam_dl(struct task_struct *p, struct sched_attr *attr);
 extern bool __checkparam_dl(const struct sched_attr *attr);
 extern bool dl_param_changed(struct task_struct *p, const struct sched_attr *attr);
-extern int  dl_task_can_attach(struct task_struct *p, const struct cpumask *cs_cpus_allowed);
 extern int  dl_cpuset_cpumask_can_shrink(const struct cpumask *cur, const struct cpumask *trial);
-extern bool dl_cpu_busy(unsigned int cpu);
+extern int  dl_bw_check_overflow(int cpu);
 
 #ifdef CONFIG_CGROUP_SCHED
 
@@ -486,6 +485,7 @@
 extern void start_cfs_bandwidth(struct cfs_bandwidth *cfs_b);
 extern void unthrottle_cfs_rq(struct cfs_rq *cfs_rq);
 
+extern void unregister_rt_sched_group(struct task_group *tg);
 extern void free_rt_sched_group(struct task_group *tg);
 extern int alloc_rt_sched_group(struct task_group *tg, struct task_group *parent);
 extern void init_tg_rt_entry(struct task_group *tg, struct rt_rq *rt_rq,
@@ -501,7 +501,7 @@
 extern void sched_online_group(struct task_group *tg,
 			       struct task_group *parent);
 extern void sched_destroy_group(struct task_group *tg);
-extern void sched_offline_group(struct task_group *tg);
+extern void sched_release_group(struct task_group *tg);
 
 extern void sched_move_task(struct task_struct *tsk);
 
@@ -575,6 +575,7 @@
 	} removed;
 
 #ifdef CONFIG_FAIR_GROUP_SCHED
+	u64			last_update_tg_load_avg;
 	unsigned long		tg_load_avg_contrib;
 	long			propagate;
 	long			prop_runnable_sum;
@@ -614,8 +615,8 @@
 	s64			runtime_remaining;
 
 	u64			throttled_clock;
-	u64			throttled_clock_task;
-	u64			throttled_clock_task_time;
+	u64			throttled_clock_pelt;
+	u64			throttled_clock_pelt_time;
 	int			throttled;
 	int			throttle_count;
 	struct list_head	throttled_list;
@@ -1003,6 +1004,7 @@
 
 	unsigned long		cpu_capacity;
 	unsigned long		cpu_capacity_orig;
+	unsigned long		cpu_capacity_inverted;
 
 	struct callback_head	*balance_callback;
 
@@ -1148,6 +1150,14 @@
 #endif
 }
 
+DECLARE_PER_CPU_SHARED_ALIGNED(struct rq, runqueues);
+
+#define cpu_rq(cpu)		(&per_cpu(runqueues, (cpu)))
+#define this_rq()		this_cpu_ptr(&runqueues)
+#define task_rq(p)		cpu_rq(task_cpu(p))
+#define cpu_curr(cpu)		(cpu_rq(cpu)->curr)
+#define raw_rq()		raw_cpu_ptr(&runqueues)
+
 struct sched_group;
 #ifdef CONFIG_SCHED_CORE
 static inline struct cpumask *sched_group_span(struct sched_group *sg);
@@ -1235,7 +1245,7 @@
 		return true;
 
 	for_each_cpu_and(cpu, sched_group_span(group), p->cpus_ptr) {
-		if (sched_core_cookie_match(rq, p))
+		if (sched_core_cookie_match(cpu_rq(cpu), p))
 			return true;
 	}
 	return false;
@@ -1361,14 +1371,6 @@
 static inline void update_idle_core(struct rq *rq) { }
 #endif
 
-DECLARE_PER_CPU_SHARED_ALIGNED(struct rq, runqueues);
-
-#define cpu_rq(cpu)		(&per_cpu(runqueues, (cpu)))
-#define this_rq()		this_cpu_ptr(&runqueues)
-#define task_rq(p)		cpu_rq(task_cpu(p))
-#define cpu_curr(cpu)		(cpu_rq(cpu)->curr)
-#define raw_rq()		raw_cpu_ptr(&runqueues)
-
 #ifdef CONFIG_FAIR_GROUP_SCHED
 static inline struct task_struct *task_of(struct sched_entity *se)
 {
@@ -1717,6 +1719,11 @@
 {
 	lockdep_assert_rq_held(rq);
 
+	/*
+	 * Don't (re)queue an already queued item; nor queue anything when
+	 * balance_push() is active, see the comment with
+	 * balance_push_callback.
+	 */
 	if (unlikely(head->next || rq->balance_callback == &balance_push_callback))
 		return;
 
@@ -1783,6 +1790,11 @@
 DECLARE_PER_CPU(struct sched_domain __rcu *, sd_asym_cpucapacity);
 extern struct static_key_false sched_asym_cpucapacity;
 
+static __always_inline bool sched_asym_cpucap_active(void)
+{
+	return static_branch_unlikely(&sched_asym_cpucapacity);
+}
+
 struct sched_group_capacity {
 	atomic_t		ref;
 	/*
@@ -1809,6 +1821,7 @@
 	unsigned int		group_weight;
 	struct sched_group_capacity *sgc;
 	int			asym_prefer_cpu;	/* CPU of highest priority in group */
+	int			flags;
 
 	/*
 	 * The CPUs this group covers.
@@ -2047,7 +2060,6 @@
 
 #define WF_SYNC     0x10 /* Waker goes to sleep after wakeup */
 #define WF_MIGRATED 0x20 /* Internal use, task got migrated */
-#define WF_ON_CPU   0x40 /* Wakee is on_cpu */
 
 #ifdef CONFIG_SMP
 static_assert(WF_EXEC == SD_BALANCE_EXEC);
@@ -2312,7 +2324,7 @@
 extern void init_sched_rt_class(void);
 extern void init_sched_fair_class(void);
 
-extern void reweight_task(struct task_struct *p, int prio);
+extern void reweight_task(struct task_struct *p, const struct load_weight *lw);
 
 extern void resched_curr(struct rq *rq);
 extern void resched_cpu(int cpu);
@@ -2488,6 +2500,24 @@
 }
 #endif
 
+#ifdef CONFIG_SCHED_DEBUG
+/*
+ * In double_lock_balance()/double_rq_lock(), we use raw_spin_rq_lock() to
+ * acquire rq lock instead of rq_lock(). So at the end of these two functions
+ * we need to call double_rq_clock_clear_update() to clear RQCF_UPDATED of
+ * rq->clock_update_flags to avoid the WARN_DOUBLE_CLOCK warning.
+ */
+static inline void double_rq_clock_clear_update(struct rq *rq1, struct rq *rq2)
+{
+	rq1->clock_update_flags &= (RQCF_REQ_SKIP|RQCF_ACT_SKIP);
+	/* rq1 == rq2 for !CONFIG_SMP, so just clear RQCF_UPDATED once. */
+#ifdef CONFIG_SMP
+	rq2->clock_update_flags &= (RQCF_REQ_SKIP|RQCF_ACT_SKIP);
+#endif
+}
+#else
+static inline void double_rq_clock_clear_update(struct rq *rq1, struct rq *rq2) {}
+#endif
 
 #ifdef CONFIG_SMP
 
@@ -2553,14 +2583,15 @@
 	__acquires(busiest->lock)
 	__acquires(this_rq->lock)
 {
-	if (__rq_lockp(this_rq) == __rq_lockp(busiest))
-		return 0;
-
-	if (likely(raw_spin_rq_trylock(busiest)))
+	if (__rq_lockp(this_rq) == __rq_lockp(busiest) ||
+	    likely(raw_spin_rq_trylock(busiest))) {
+		double_rq_clock_clear_update(this_rq, busiest);
 		return 0;
+	}
 
 	if (rq_order_less(this_rq, busiest)) {
 		raw_spin_rq_lock_nested(busiest, SINGLE_DEPTH_NESTING);
+		double_rq_clock_clear_update(this_rq, busiest);
 		return 0;
 	}
 
@@ -2654,6 +2685,7 @@
 	BUG_ON(rq1 != rq2);
 	raw_spin_rq_lock(rq1);
 	__acquire(rq2->lock);	/* Fake it out ;) */
+	double_rq_clock_clear_update(rq1, rq2);
 }
 
 /*
@@ -2709,12 +2741,18 @@
 #define NOHZ_BALANCE_KICK_BIT	0
 #define NOHZ_STATS_KICK_BIT	1
 #define NOHZ_NEWILB_KICK_BIT	2
+#define NOHZ_NEXT_KICK_BIT	3
 
+/* Run rebalance_domains() */
 #define NOHZ_BALANCE_KICK	BIT(NOHZ_BALANCE_KICK_BIT)
+/* Update blocked load */
 #define NOHZ_STATS_KICK		BIT(NOHZ_STATS_KICK_BIT)
+/* Update blocked load when entering idle */
 #define NOHZ_NEWILB_KICK	BIT(NOHZ_NEWILB_KICK_BIT)
+/* Update nohz.next_balance */
+#define NOHZ_NEXT_KICK		BIT(NOHZ_NEXT_KICK_BIT)
 
-#define NOHZ_KICK_MASK	(NOHZ_BALANCE_KICK | NOHZ_STATS_KICK)
+#define NOHZ_KICK_MASK	(NOHZ_BALANCE_KICK | NOHZ_STATS_KICK | NOHZ_NEXT_KICK)
 
 #define nohz_flags(cpu)	(&cpu_rq(cpu)->nohz_flags)
 
@@ -2826,6 +2864,23 @@
 #ifdef CONFIG_UCLAMP_TASK
 unsigned long uclamp_eff_value(struct task_struct *p, enum uclamp_id clamp_id);
 
+static inline unsigned long uclamp_rq_get(struct rq *rq,
+					  enum uclamp_id clamp_id)
+{
+	return READ_ONCE(rq->uclamp[clamp_id].value);
+}
+
+static inline void uclamp_rq_set(struct rq *rq, enum uclamp_id clamp_id,
+				 unsigned int value)
+{
+	WRITE_ONCE(rq->uclamp[clamp_id].value, value);
+}
+
+static inline bool uclamp_rq_is_idle(struct rq *rq)
+{
+	return rq->uclamp_flags & UCLAMP_FLAG_IDLE;
+}
+
 /**
  * uclamp_rq_util_with - clamp @util with @rq and @p effective uclamp values.
  * @rq:		The rq to clamp against. Must not be NULL.
@@ -2861,12 +2916,12 @@
 		 * Ignore last runnable task's max clamp, as this task will
 		 * reset it. Similarly, no need to read the rq's min clamp.
 		 */
-		if (rq->uclamp_flags & UCLAMP_FLAG_IDLE)
+		if (uclamp_rq_is_idle(rq))
 			goto out;
 	}
 
-	min_util = max_t(unsigned long, min_util, READ_ONCE(rq->uclamp[UCLAMP_MIN].value));
-	max_util = max_t(unsigned long, max_util, READ_ONCE(rq->uclamp[UCLAMP_MAX].value));
+	min_util = max_t(unsigned long, min_util, uclamp_rq_get(rq, UCLAMP_MIN));
+	max_util = max_t(unsigned long, max_util, uclamp_rq_get(rq, UCLAMP_MAX));
 out:
 	/*
 	 * Since CPU's {min,max}_util clamps are MAX aggregated considering
@@ -2892,6 +2947,15 @@
 	return static_branch_likely(&sched_uclamp_used);
 }
 #else /* CONFIG_UCLAMP_TASK */
+static inline unsigned long uclamp_eff_value(struct task_struct *p,
+					     enum uclamp_id clamp_id)
+{
+	if (clamp_id == UCLAMP_MIN)
+		return 0;
+
+	return SCHED_CAPACITY_SCALE;
+}
+
 static inline
 unsigned long uclamp_rq_util_with(struct rq *rq, unsigned long util,
 				  struct task_struct *p)
@@ -2903,6 +2967,25 @@
 {
 	return false;
 }
+
+static inline unsigned long uclamp_rq_get(struct rq *rq,
+					  enum uclamp_id clamp_id)
+{
+	if (clamp_id == UCLAMP_MIN)
+		return 0;
+
+	return SCHED_CAPACITY_SCALE;
+}
+
+static inline void uclamp_rq_set(struct rq *rq, enum uclamp_id clamp_id,
+				 unsigned int value)
+{
+}
+
+static inline bool uclamp_rq_is_idle(struct rq *rq)
+{
+	return false;
+}
 #endif /* CONFIG_UCLAMP_TASK */
 
 #ifdef arch_scale_freq_capacity
@@ -2919,6 +3002,24 @@
 	return cpu_rq(cpu)->cpu_capacity_orig;
 }
 
+/*
+ * Returns inverted capacity if the CPU is in capacity inversion state.
+ * 0 otherwise.
+ *
+ * Capacity inversion detection only considers thermal impact where actual
+ * performance points (OPPs) gets dropped.
+ *
+ * Capacity inversion state happens when another performance domain that has
+ * equal or lower capacity_orig_of() becomes effectively larger than the perf
+ * domain this CPU belongs to due to thermal pressure throttling it hard.
+ *
+ * See comment in update_cpu_capacity().
+ */
+static inline unsigned long cpu_in_capacity_inversion(int cpu)
+{
+	return cpu_rq(cpu)->cpu_capacity_inverted;
+}
+
 /**
  * enum cpu_util_type - CPU utilization type
  * @FREQUENCY_UTIL:	Utilization used to select frequency
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/stats.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/stats.h
@@ -41,6 +41,7 @@
 #define   schedstat_val_or_zero(var)	((schedstat_enabled()) ? (var) : 0)
 
 #else /* !CONFIG_SCHEDSTATS: */
+
 static inline void rq_sched_info_arrive  (struct rq *rq, unsigned long long delta) { }
 static inline void rq_sched_info_dequeue(struct rq *rq, unsigned long long delta) { }
 static inline void rq_sched_info_depart  (struct rq *rq, unsigned long long delta) { }
@@ -53,8 +54,26 @@
 # define   schedstat_set(var, val)	do { } while (0)
 # define   schedstat_val(var)		0
 # define   schedstat_val_or_zero(var)	0
+
 #endif /* CONFIG_SCHEDSTATS */
 
+#ifdef CONFIG_FAIR_GROUP_SCHED
+struct sched_entity_stats {
+	struct sched_entity     se;
+	struct sched_statistics stats;
+} __no_randomize_layout;
+#endif
+
+static inline struct sched_statistics *
+__schedstats_from_se(struct sched_entity *se)
+{
+#ifdef CONFIG_FAIR_GROUP_SCHED
+	if (!entity_is_task(se))
+		return &container_of(se, struct sched_entity_stats, se)->stats;
+#endif
+	return &task_of(se)->stats;
+}
+
 #ifdef CONFIG_PSI
 /*
  * PSI tracks state that persists across sleeps, such as iowaits and
@@ -69,11 +88,12 @@
 	if (static_branch_likely(&psi_disabled))
 		return;
 
-	if (!wakeup || p->sched_psi_wake_requeue) {
+	if (p->in_memstall)
+		set |= TSK_MEMSTALL_RUNNING;
+
+	if (!wakeup) {
 		if (p->in_memstall)
 			set |= TSK_MEMSTALL;
-		if (p->sched_psi_wake_requeue)
-			p->sched_psi_wake_requeue = 0;
 	} else {
 		if (p->in_iowait)
 			clear |= TSK_IOWAIT;
@@ -84,8 +104,6 @@
 
 static inline void psi_dequeue(struct task_struct *p, bool sleep)
 {
-	int clear = TSK_RUNNING;
-
 	if (static_branch_likely(&psi_disabled))
 		return;
 
@@ -98,10 +116,7 @@
 	if (sleep)
 		return;
 
-	if (p->in_memstall)
-		clear |= TSK_MEMSTALL;
-
-	psi_task_change(p, clear, 0);
+	psi_task_change(p, p->psi_flags, 0);
 }
 
 static inline void psi_ttwu_dequeue(struct task_struct *p)
@@ -113,19 +128,12 @@
 	 * deregister its sleep-persistent psi states from the old
 	 * queue, and let psi_enqueue() know it has to requeue.
 	 */
-	if (unlikely(p->in_iowait || p->in_memstall)) {
+	if (unlikely(p->psi_flags)) {
 		struct rq_flags rf;
 		struct rq *rq;
-		int clear = 0;
-
-		if (p->in_iowait)
-			clear |= TSK_IOWAIT;
-		if (p->in_memstall)
-			clear |= TSK_MEMSTALL;
 
 		rq = __task_rq_lock(p, &rf);
-		psi_task_change(p, clear, 0);
-		p->sched_psi_wake_requeue = 1;
+		psi_task_change(p, p->psi_flags, 0);
 		__task_rq_unlock(rq, &rf);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/stop_task.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/stop_task.c
@@ -78,8 +78,8 @@
 	if (unlikely((s64)delta_exec < 0))
 		delta_exec = 0;
 
-	schedstat_set(curr->se.statistics.exec_max,
-			max(curr->se.statistics.exec_max, delta_exec));
+	schedstat_set(curr->stats.exec_max,
+		      max(curr->stats.exec_max, delta_exec));
 
 	curr->se.sum_exec_runtime += delta_exec;
 	account_group_exec_runtime(curr, delta_exec);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/topology.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/topology.c
@@ -716,8 +716,20 @@
 		tmp = sd;
 		sd = sd->parent;
 		destroy_sched_domain(tmp);
-		if (sd)
+		if (sd) {
+			struct sched_group *sg = sd->groups;
+
+			/*
+			 * sched groups hold the flags of the child sched
+			 * domain for convenience. Clear such flags since
+			 * the child is being destroyed.
+			 */
+			do {
+				sg->flags = 0;
+			} while (sg != sd->groups);
+
 			sd->child = NULL;
+		}
 	}
 
 	for (tmp = sd; tmp; tmp = tmp->parent)
@@ -916,10 +928,12 @@
 		return NULL;
 
 	sg_span = sched_group_span(sg);
-	if (sd->child)
+	if (sd->child) {
 		cpumask_copy(sg_span, sched_domain_span(sd->child));
-	else
+		sg->flags = sd->child->flags;
+	} else {
 		cpumask_copy(sg_span, sched_domain_span(sd));
+	}
 
 	atomic_inc(&sg->ref);
 	return sg;
@@ -1169,6 +1183,7 @@
 	if (child) {
 		cpumask_copy(sched_group_span(sg), sched_domain_span(child));
 		cpumask_copy(group_balance_mask(sg), sched_group_span(sg));
+		sg->flags = child->flags;
 	} else {
 		cpumask_set_cpu(cpu, sched_group_span(sg));
 		cpumask_set_cpu(cpu, group_balance_mask(sg));
@@ -1405,7 +1420,7 @@
 	} else
 		request = attr->relax_domain_level;
 
-	if (sd->level > request) {
+	if (sd->level >= request) {
 		/* Turn off idle balance on this domain: */
 		sd->flags &= ~(SD_BALANCE_WAKE|SD_BALANCE_NEWIDLE);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sched/wait.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sched/wait.c
@@ -238,6 +238,14 @@
 }
 EXPORT_SYMBOL_GPL(__wake_up_sync);	/* For internal use only */
 
+void __wake_up_pollfree(struct wait_queue_head *wq_head)
+{
+	__wake_up(wq_head, TASK_NORMAL, 0, poll_to_key(EPOLLHUP | POLLFREE));
+	/* POLLFREE must have cleared the queue. */
+	WARN_ON_ONCE(waitqueue_active(wq_head));
+}
+EXPORT_SYMBOL_GPL(__wake_up_pollfree);
+
 /*
  * Note: we use "set_current_state()" _after_ the wait-queue add,
  * because we need a memory barrier there on SMP, so that any
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/scs.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/scs.c
@@ -78,6 +78,7 @@
 		if (this_cpu_cmpxchg(scs_cache[i], 0, s) == NULL)
 			return;
 
+	kasan_unpoison_vmalloc(s, SCS_SIZE);
 	vfree_atomic(s);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/seccomp.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/seccomp.c
@@ -29,6 +29,9 @@
 #include <linux/syscalls.h>
 #include <linux/sysctl.h>
 
+/* Not exposed in headers: strictly internal use only. */
+#define SECCOMP_MODE_DEAD	(SECCOMP_MODE_FILTER + 1)
+
 #ifdef CONFIG_HAVE_ARCH_SECCOMP_FILTER
 #include <asm/syscall.h>
 #endif
@@ -1010,6 +1013,7 @@
 #ifdef SECCOMP_DEBUG
 	dump_stack();
 #endif
+	current->seccomp.mode = SECCOMP_MODE_DEAD;
 	seccomp_log(this_syscall, SIGKILL, SECCOMP_RET_KILL_THREAD, true);
 	do_exit(SIGKILL);
 }
@@ -1261,6 +1265,7 @@
 	case SECCOMP_RET_KILL_THREAD:
 	case SECCOMP_RET_KILL_PROCESS:
 	default:
+		current->seccomp.mode = SECCOMP_MODE_DEAD;
 		seccomp_log(this_syscall, SIGSYS, action, true);
 		/* Dump core only if this is the last remaining thread. */
 		if (action != SECCOMP_RET_KILL_THREAD ||
@@ -1309,6 +1314,11 @@
 		return 0;
 	case SECCOMP_MODE_FILTER:
 		return __seccomp_filter(this_syscall, sd, false);
+	/* Surviving SECCOMP_RET_KILL_* must be proactively impossible. */
+	case SECCOMP_MODE_DEAD:
+		WARN_ON_ONCE(1);
+		do_exit(SIGKILL);
+		return -1;
 	default:
 		BUG();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/signal.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/signal.c
@@ -1298,6 +1298,12 @@
 	return ret;
 }
 
+enum sig_handler {
+	HANDLER_CURRENT, /* If reachable use the current handler */
+	HANDLER_SIG_DFL, /* Always use SIG_DFL handler semantics */
+	HANDLER_EXIT,	 /* Only visible as the process exit code */
+};
+
 /*
  * Force a signal that the process can't ignore: if necessary
  * we unblock the signal and change any SIG_IGN to SIG_DFL.
@@ -1310,7 +1316,8 @@
  * that is why we also clear SIGNAL_UNKILLABLE.
  */
 static int
-force_sig_info_to_task(struct kernel_siginfo *info, struct task_struct *t, bool sigdfl)
+force_sig_info_to_task(struct kernel_siginfo *info, struct task_struct *t,
+	enum sig_handler handler)
 {
 	unsigned long int flags;
 	int ret, blocked, ignored;
@@ -1321,8 +1328,10 @@
 	action = &t->sighand->action[sig-1];
 	ignored = action->sa.sa_handler == SIG_IGN;
 	blocked = sigismember(&t->blocked, sig);
-	if (blocked || ignored || sigdfl) {
+	if (blocked || ignored || (handler != HANDLER_CURRENT)) {
 		action->sa.sa_handler = SIG_DFL;
+		if (handler == HANDLER_EXIT)
+			action->sa.sa_flags |= SA_IMMUTABLE;
 		if (blocked) {
 			sigdelset(&t->blocked, sig);
 			recalc_sigpending_and_wake(t);
@@ -1330,9 +1339,10 @@
 	}
 	/*
 	 * Don't clear SIGNAL_UNKILLABLE for traced tasks, users won't expect
-	 * debugging to leave init killable.
+	 * debugging to leave init killable. But HANDLER_EXIT is always fatal.
 	 */
-	if (action->sa.sa_handler == SIG_DFL && !t->ptrace)
+	if (action->sa.sa_handler == SIG_DFL &&
+	    (!t->ptrace || (handler == HANDLER_EXIT)))
 		t->signal->flags &= ~SIGNAL_UNKILLABLE;
 	ret = send_signal(sig, info, t, PIDTYPE_PID);
 	spin_unlock_irqrestore(&t->sighand->siglock, flags);
@@ -1342,7 +1352,7 @@
 
 int force_sig_info(struct kernel_siginfo *info)
 {
-	return force_sig_info_to_task(info, current, false);
+	return force_sig_info_to_task(info, current, HANDLER_CURRENT);
 }
 
 /*
@@ -1649,6 +1659,32 @@
 }
 EXPORT_SYMBOL(force_sig);
 
+void force_fatal_sig(int sig)
+{
+	struct kernel_siginfo info;
+
+	clear_siginfo(&info);
+	info.si_signo = sig;
+	info.si_errno = 0;
+	info.si_code = SI_KERNEL;
+	info.si_pid = 0;
+	info.si_uid = 0;
+	force_sig_info_to_task(&info, current, HANDLER_SIG_DFL);
+}
+
+void force_exit_sig(int sig)
+{
+	struct kernel_siginfo info;
+
+	clear_siginfo(&info);
+	info.si_signo = sig;
+	info.si_errno = 0;
+	info.si_code = SI_KERNEL;
+	info.si_pid = 0;
+	info.si_uid = 0;
+	force_sig_info_to_task(&info, current, HANDLER_EXIT);
+}
+
 /*
  * When things go south during signal handling, we
  * will force a SIGSEGV. And if the signal that caused
@@ -1657,15 +1693,10 @@
  */
 void force_sigsegv(int sig)
 {
-	struct task_struct *p = current;
-
-	if (sig == SIGSEGV) {
-		unsigned long flags;
-		spin_lock_irqsave(&p->sighand->siglock, flags);
-		p->sighand->action[sig - 1].sa.sa_handler = SIG_DFL;
-		spin_unlock_irqrestore(&p->sighand->siglock, flags);
-	}
-	force_sig(SIGSEGV);
+	if (sig == SIGSEGV)
+		force_fatal_sig(SIGSEGV);
+	else
+		force_sig(SIGSEGV);
 }
 
 int force_sig_fault_to_task(int sig, int code, void __user *addr
@@ -1684,7 +1715,7 @@
 	info.si_flags = flags;
 	info.si_isr = isr;
 #endif
-	return force_sig_info_to_task(&info, t, false);
+	return force_sig_info_to_task(&info, t, HANDLER_CURRENT);
 }
 
 int force_sig_fault(int sig, int code, void __user *addr
@@ -1771,7 +1802,7 @@
 }
 #endif
 
-int force_sig_perf(void __user *addr, u32 type, u64 sig_data)
+int send_sig_perf(void __user *addr, u32 type, u64 sig_data)
 {
 	struct kernel_siginfo info;
 
@@ -1783,7 +1814,18 @@
 	info.si_perf_data = sig_data;
 	info.si_perf_type = type;
 
-	return force_sig_info(&info);
+	/*
+	 * Signals generated by perf events should not terminate the whole
+	 * process if SIGTRAP is blocked, however, delivering the signal
+	 * asynchronously is better than not delivering at all. But tell user
+	 * space if the signal was asynchronous, so it can clearly be
+	 * distinguished from normal synchronous ones.
+	 */
+	info.si_perf_flags = sigismember(&current->blocked, info.si_signo) ?
+				     TRAP_PERF_FLAG_ASYNC :
+				     0;
+
+	return send_sig_info(info.si_signo, &info, current);
 }
 
 /**
@@ -1804,7 +1846,8 @@
 	info.si_errno = reason;
 	info.si_arch = syscall_get_arch(current);
 	info.si_syscall = syscall;
-	return force_sig_info_to_task(&info, current, force_coredump);
+	return force_sig_info_to_task(&info, current,
+		force_coredump ? HANDLER_EXIT : HANDLER_CURRENT);
 }
 
 /* For the crazy architectures that include trap information in
@@ -1889,10 +1932,11 @@
 
 void sigqueue_free(struct sigqueue *q)
 {
-	unsigned long flags;
 	spinlock_t *lock = &current->sighand->siglock;
+	unsigned long flags;
 
-	BUG_ON(!(q->flags & SIGQUEUE_PREALLOC));
+	if (WARN_ON_ONCE(!(q->flags & SIGQUEUE_PREALLOC)))
+		return;
 	/*
 	 * We must hold ->siglock while testing q->list
 	 * to serialize with collect_signal() or with
@@ -1920,7 +1964,10 @@
 	unsigned long flags;
 	int ret, result;
 
-	BUG_ON(!(q->flags & SIGQUEUE_PREALLOC));
+	if (WARN_ON_ONCE(!(q->flags & SIGQUEUE_PREALLOC)))
+		return 0;
+	if (WARN_ON_ONCE(q->info.si_code != SI_TIMER))
+		return 0;
 
 	ret = -1;
 	rcu_read_lock();
@@ -1939,7 +1986,6 @@
 		 * If an SI_TIMER entry is already queue just increment
 		 * the overrun count.
 		 */
-		BUG_ON(q->info.si_code != SI_TIMER);
 		q->info.si_overrun++;
 		result = TRACE_SIGNAL_ALREADY_PENDING;
 		goto out;
@@ -1984,12 +2030,12 @@
 	bool autoreap = false;
 	u64 utime, stime;
 
-	BUG_ON(sig == -1);
+	WARN_ON_ONCE(sig == -1);
 
- 	/* do_notify_parent_cldstop should have been called instead.  */
- 	BUG_ON(task_is_stopped_or_traced(tsk));
+	/* do_notify_parent_cldstop should have been called instead.  */
+	WARN_ON_ONCE(task_is_stopped_or_traced(tsk));
 
-	BUG_ON(!tsk->ptrace &&
+	WARN_ON_ONCE(!tsk->ptrace &&
 	       (tsk->group_leader != tsk || !thread_group_empty(tsk)));
 
 	/* Wake up all pidfd waiters */
@@ -2169,15 +2215,6 @@
 	return true;
 }
 
-/*
- * Return non-zero if there is a SIGKILL that should be waking us up.
- * Called with the siglock held.
- */
-static bool sigkill_pending(struct task_struct *tsk)
-{
-	return sigismember(&tsk->pending.signal, SIGKILL) ||
-	       sigismember(&tsk->signal->shared_pending.signal, SIGKILL);
-}
 
 /*
  * This must be called with current->sighand->siglock held.
@@ -2204,17 +2241,16 @@
 		 * calling arch_ptrace_stop, so we must release it now.
 		 * To preserve proper semantics, we must do this before
 		 * any signal bookkeeping like checking group_stop_count.
-		 * Meanwhile, a SIGKILL could come in before we retake the
-		 * siglock.  That must prevent us from sleeping in TASK_TRACED.
-		 * So after regaining the lock, we must check for SIGKILL.
 		 */
 		spin_unlock_irq(&current->sighand->siglock);
 		arch_ptrace_stop(exit_code, info);
 		spin_lock_irq(&current->sighand->siglock);
-		if (sigkill_pending(current))
-			return;
 	}
 
+	/*
+	 * schedule() will not sleep if there is a pending signal that
+	 * can awaken the task.
+	 */
 	set_special_state(TASK_TRACED);
 
 	/*
@@ -2546,6 +2582,14 @@
 	spin_unlock_irq(&current->sighand->siglock);
 	cgroup_enter_frozen();
 	freezable_schedule();
+
+	/*
+	 * We could've been woken by task_work, run it to clear
+	 * TIF_NOTIFY_SIGNAL. The caller will retry if necessary.
+	 */
+	clear_notify_signal();
+	if (unlikely(READ_ONCE(current->task_works)))
+		task_work_run();
 }
 
 static int ptrace_signal(int signr, kernel_siginfo_t *info)
@@ -2688,19 +2732,19 @@
 		goto relock;
 	}
 
-	/* Has this task already been marked for death? */
-	if (signal_group_exit(signal)) {
-		ksig->info.si_signo = signr = SIGKILL;
-		sigdelset(&current->pending.signal, SIGKILL);
-		trace_signal_deliver(SIGKILL, SEND_SIG_NOINFO,
-				&sighand->action[SIGKILL - 1]);
-		recalc_sigpending();
-		goto fatal;
-	}
-
 	for (;;) {
 		struct k_sigaction *ka;
 
+		/* Has this task already been marked for death? */
+		if (signal_group_exit(signal)) {
+			ksig->info.si_signo = signr = SIGKILL;
+			sigdelset(&current->pending.signal, SIGKILL);
+			trace_signal_deliver(SIGKILL, SEND_SIG_NOINFO,
+				&sighand->action[SIGKILL - 1]);
+			recalc_sigpending();
+			goto fatal;
+		}
+
 		if (unlikely(current->jobctl & JOBCTL_STOP_PENDING) &&
 		    do_signal_stop(0))
 			goto relock;
@@ -2739,7 +2783,8 @@
 		if (!signr)
 			break; /* will return 0 */
 
-		if (unlikely(current->ptrace) && signr != SIGKILL) {
+		if (unlikely(current->ptrace) && (signr != SIGKILL) &&
+		    !(sighand->action[signr -1].sa.sa_flags & SA_IMMUTABLE)) {
 			signr = ptrace_signal(signr, &ksig->info);
 			if (!signr)
 				continue;
@@ -3422,6 +3467,7 @@
 		to->si_addr = ptr_to_compat(from->si_addr);
 		to->si_perf_data = from->si_perf_data;
 		to->si_perf_type = from->si_perf_type;
+		to->si_perf_flags = from->si_perf_flags;
 		break;
 	case SIL_CHLD:
 		to->si_pid = from->si_pid;
@@ -3499,6 +3545,7 @@
 		to->si_addr = compat_ptr(from->si_addr);
 		to->si_perf_data = from->si_perf_data;
 		to->si_perf_type = from->si_perf_type;
+		to->si_perf_flags = from->si_perf_flags;
 		break;
 	case SIL_CHLD:
 		to->si_pid    = from->si_pid;
@@ -4089,6 +4136,10 @@
 	k = &p->sighand->action[sig-1];
 
 	spin_lock_irq(&p->sighand->siglock);
+	if (k->sa.sa_flags & SA_IMMUTABLE) {
+		spin_unlock_irq(&p->sighand->siglock);
+		return -EINVAL;
+	}
 	if (oact)
 		*oact = *k;
 
@@ -4138,11 +4189,29 @@
 	return 0;
 }
 
+#ifdef CONFIG_DYNAMIC_SIGFRAME
+static inline void sigaltstack_lock(void)
+	__acquires(&current->sighand->siglock)
+{
+	spin_lock_irq(&current->sighand->siglock);
+}
+
+static inline void sigaltstack_unlock(void)
+	__releases(&current->sighand->siglock)
+{
+	spin_unlock_irq(&current->sighand->siglock);
+}
+#else
+static inline void sigaltstack_lock(void) { }
+static inline void sigaltstack_unlock(void) { }
+#endif
+
 static int
 do_sigaltstack (const stack_t *ss, stack_t *oss, unsigned long sp,
 		size_t min_ss_size)
 {
 	struct task_struct *t = current;
+	int ret = 0;
 
 	if (oss) {
 		memset(oss, 0, sizeof(stack_t));
@@ -4166,19 +4235,33 @@
 				ss_mode != 0))
 			return -EINVAL;
 
+		/*
+		 * Return before taking any locks if no actual
+		 * sigaltstack changes were requested.
+		 */
+		if (t->sas_ss_sp == (unsigned long)ss_sp &&
+		    t->sas_ss_size == ss_size &&
+		    t->sas_ss_flags == ss_flags)
+			return 0;
+
+		sigaltstack_lock();
 		if (ss_mode == SS_DISABLE) {
 			ss_size = 0;
 			ss_sp = NULL;
 		} else {
 			if (unlikely(ss_size < min_ss_size))
-				return -ENOMEM;
+				ret = -ENOMEM;
+			if (!sigaltstack_size_valid(ss_size))
+				ret = -ENOMEM;
 		}
-
-		t->sas_ss_sp = (unsigned long) ss_sp;
-		t->sas_ss_size = ss_size;
-		t->sas_ss_flags = ss_flags;
+		if (!ret) {
+			t->sas_ss_sp = (unsigned long) ss_sp;
+			t->sas_ss_size = ss_size;
+			t->sas_ss_flags = ss_flags;
+		}
+		sigaltstack_unlock();
 	}
-	return 0;
+	return ret;
 }
 
 SYSCALL_DEFINE2(sigaltstack,const stack_t __user *,uss, stack_t __user *,uoss)
@@ -4675,6 +4758,7 @@
 	CHECK_OFFSET(si_pkey);
 	CHECK_OFFSET(si_perf_data);
 	CHECK_OFFSET(si_perf_type);
+	CHECK_OFFSET(si_perf_flags);
 
 	/* sigpoll */
 	CHECK_OFFSET(si_band);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/smp.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/smp.c
@@ -174,9 +174,9 @@
 	if (val)
 		static_branch_enable(&csdlock_debug_enabled);
 
-	return 0;
+	return 1;
 }
-early_param("csdlock_debug", csdlock_debug);
+__setup("csdlock_debug=", csdlock_debug);
 
 static DEFINE_PER_CPU(call_single_data_t *, cur_csd);
 static DEFINE_PER_CPU(smp_call_func_t, cur_csd_func);
@@ -579,7 +579,7 @@
 
 	/* There shouldn't be any pending callbacks on an offline CPU. */
 	if (unlikely(warn_cpu_offline && !cpu_online(smp_processor_id()) &&
-		     !warned && !llist_empty(head))) {
+		     !warned && entry != NULL)) {
 		warned = true;
 		WARN(1, "IPI on offline CPU %d\n", smp_processor_id());
 
@@ -1170,14 +1170,12 @@
 {
 	int cpu;
 
-	preempt_disable();
-	for_each_online_cpu(cpu) {
-		if (cpu == smp_processor_id())
-			continue;
-
-		wake_up_if_idle(cpu);
+	for_each_possible_cpu(cpu) {
+		preempt_disable();
+		if (cpu != smp_processor_id() && cpu_online(cpu))
+			wake_up_if_idle(cpu);
+		preempt_enable();
 	}
-	preempt_enable();
 }
 EXPORT_SYMBOL_GPL(wake_up_all_idle_cpus);
 
@@ -1233,6 +1231,7 @@
 
 	queue_work_on(cpu, system_wq, &sscs.work);
 	wait_for_completion(&sscs.done);
+	destroy_work_on_stack(&sscs.work);
 
 	return sscs.ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/softirq.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/softirq.c
@@ -512,7 +512,7 @@
 static inline void lockdep_softirq_end(bool in_hardirq) { }
 #endif
 
-asmlinkage __visible void __softirq_entry __do_softirq(void)
+static void handle_softirqs(bool ksirqd)
 {
 	unsigned long end = jiffies + MAX_SOFTIRQ_TIME;
 	unsigned long old_flags = current->flags;
@@ -567,8 +567,7 @@
 		pending >>= softirq_bit;
 	}
 
-	if (!IS_ENABLED(CONFIG_PREEMPT_RT) &&
-	    __this_cpu_read(ksoftirqd) == current)
+	if (!IS_ENABLED(CONFIG_PREEMPT_RT) && ksirqd)
 		rcu_softirq_qs();
 
 	local_irq_disable();
@@ -588,6 +587,11 @@
 	current_restore_flags(old_flags, PF_MEMALLOC);
 }
 
+asmlinkage __visible void __softirq_entry __do_softirq(void)
+{
+	handle_softirqs(false);
+}
+
 /**
  * irq_enter_rcu - Enter an interrupt context with RCU watching
  */
@@ -595,7 +599,8 @@
 {
 	__irq_enter_raw();
 
-	if (is_idle_task(current) && (irq_count() == HARDIRQ_OFFSET))
+	if (tick_nohz_full_cpu(smp_processor_id()) ||
+	    (is_idle_task(current) && (irq_count() == HARDIRQ_OFFSET)))
 		tick_irq_enter();
 
 	account_hardirq_enter(current);
@@ -917,7 +922,7 @@
 		 * We can safely run softirq on inline stack, as we are not deep
 		 * in the task stack here.
 		 */
-		__do_softirq();
+		handle_softirqs(true);
 		ksoftirqd_run_end();
 		cond_resched();
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/stackleak.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/stackleak.c
@@ -48,7 +48,7 @@
 #define skip_erasing()	false
 #endif /* CONFIG_STACKLEAK_RUNTIME_DISABLE */
 
-asmlinkage void notrace stackleak_erase(void)
+asmlinkage void noinstr stackleak_erase(void)
 {
 	/* It would be nice not to have 'kstack_ptr' and 'boundary' on stack */
 	unsigned long kstack_ptr = current->lowest_stack;
@@ -102,9 +102,8 @@
 	/* Reset the 'lowest_stack' value for the next syscall */
 	current->lowest_stack = current_top_of_stack() - THREAD_SIZE/64;
 }
-NOKPROBE_SYMBOL(stackleak_erase);
 
-void __used __no_caller_saved_registers notrace stackleak_track_stack(void)
+void __used __no_caller_saved_registers noinstr stackleak_track_stack(void)
 {
 	unsigned long sp = current_stack_pointer;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/stacktrace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/stacktrace.c
@@ -13,6 +13,7 @@
 #include <linux/export.h>
 #include <linux/kallsyms.h>
 #include <linux/stacktrace.h>
+#include <linux/interrupt.h>
 
 /**
  * stack_trace_print - Print the entries in the stack trace
@@ -373,3 +374,32 @@
 #endif /* CONFIG_USER_STACKTRACE_SUPPORT */
 
 #endif /* !CONFIG_ARCH_STACKWALK */
+
+static inline bool in_irqentry_text(unsigned long ptr)
+{
+	return (ptr >= (unsigned long)&__irqentry_text_start &&
+		ptr < (unsigned long)&__irqentry_text_end) ||
+		(ptr >= (unsigned long)&__softirqentry_text_start &&
+		 ptr < (unsigned long)&__softirqentry_text_end);
+}
+
+/**
+ * filter_irq_stacks - Find first IRQ stack entry in trace
+ * @entries:	Pointer to stack trace array
+ * @nr_entries:	Number of entries in the storage array
+ *
+ * Return: Number of trace entries until IRQ stack starts.
+ */
+unsigned int filter_irq_stacks(unsigned long *entries, unsigned int nr_entries)
+{
+	unsigned int i;
+
+	for (i = 0; i < nr_entries; i++) {
+		if (in_irqentry_text(entries[i])) {
+			/* Include the irqentry function into the stack. */
+			return i + 1;
+		}
+	}
+	return nr_entries;
+}
+EXPORT_SYMBOL_GPL(filter_irq_stacks);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/static_call.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/static_call.c
@@ -1,548 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
-#include <linux/init.h>
 #include <linux/static_call.h>
-#include <linux/bug.h>
-#include <linux/smp.h>
-#include <linux/sort.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-#include <linux/cpu.h>
-#include <linux/processor.h>
-#include <asm/sections.h>
-
-extern struct static_call_site __start_static_call_sites[],
-			       __stop_static_call_sites[];
-extern struct static_call_tramp_key __start_static_call_tramp_key[],
-				    __stop_static_call_tramp_key[];
-
-static bool static_call_initialized;
-
-/* mutex to protect key modules/sites */
-static DEFINE_MUTEX(static_call_mutex);
-
-static void static_call_lock(void)
-{
-	mutex_lock(&static_call_mutex);
-}
-
-static void static_call_unlock(void)
-{
-	mutex_unlock(&static_call_mutex);
-}
-
-static inline void *static_call_addr(struct static_call_site *site)
-{
-	return (void *)((long)site->addr + (long)&site->addr);
-}
-
-static inline unsigned long __static_call_key(const struct static_call_site *site)
-{
-	return (long)site->key + (long)&site->key;
-}
-
-static inline struct static_call_key *static_call_key(const struct static_call_site *site)
-{
-	return (void *)(__static_call_key(site) & ~STATIC_CALL_SITE_FLAGS);
-}
-
-/* These assume the key is word-aligned. */
-static inline bool static_call_is_init(struct static_call_site *site)
-{
-	return __static_call_key(site) & STATIC_CALL_SITE_INIT;
-}
-
-static inline bool static_call_is_tail(struct static_call_site *site)
-{
-	return __static_call_key(site) & STATIC_CALL_SITE_TAIL;
-}
-
-static inline void static_call_set_init(struct static_call_site *site)
-{
-	site->key = (__static_call_key(site) | STATIC_CALL_SITE_INIT) -
-		    (long)&site->key;
-}
-
-static int static_call_site_cmp(const void *_a, const void *_b)
-{
-	const struct static_call_site *a = _a;
-	const struct static_call_site *b = _b;
-	const struct static_call_key *key_a = static_call_key(a);
-	const struct static_call_key *key_b = static_call_key(b);
-
-	if (key_a < key_b)
-		return -1;
-
-	if (key_a > key_b)
-		return 1;
-
-	return 0;
-}
-
-static void static_call_site_swap(void *_a, void *_b, int size)
-{
-	long delta = (unsigned long)_a - (unsigned long)_b;
-	struct static_call_site *a = _a;
-	struct static_call_site *b = _b;
-	struct static_call_site tmp = *a;
-
-	a->addr = b->addr  - delta;
-	a->key  = b->key   - delta;
-
-	b->addr = tmp.addr + delta;
-	b->key  = tmp.key  + delta;
-}
-
-static inline void static_call_sort_entries(struct static_call_site *start,
-					    struct static_call_site *stop)
-{
-	sort(start, stop - start, sizeof(struct static_call_site),
-	     static_call_site_cmp, static_call_site_swap);
-}
-
-static inline bool static_call_key_has_mods(struct static_call_key *key)
-{
-	return !(key->type & 1);
-}
-
-static inline struct static_call_mod *static_call_key_next(struct static_call_key *key)
-{
-	if (!static_call_key_has_mods(key))
-		return NULL;
-
-	return key->mods;
-}
-
-static inline struct static_call_site *static_call_key_sites(struct static_call_key *key)
-{
-	if (static_call_key_has_mods(key))
-		return NULL;
-
-	return (struct static_call_site *)(key->type & ~1);
-}
-
-void __static_call_update(struct static_call_key *key, void *tramp, void *func)
-{
-	struct static_call_site *site, *stop;
-	struct static_call_mod *site_mod, first;
-
-	cpus_read_lock();
-	static_call_lock();
-
-	if (key->func == func)
-		goto done;
-
-	key->func = func;
-
-	arch_static_call_transform(NULL, tramp, func, false);
-
-	/*
-	 * If uninitialized, we'll not update the callsites, but they still
-	 * point to the trampoline and we just patched that.
-	 */
-	if (WARN_ON_ONCE(!static_call_initialized))
-		goto done;
-
-	first = (struct static_call_mod){
-		.next = static_call_key_next(key),
-		.mod = NULL,
-		.sites = static_call_key_sites(key),
-	};
-
-	for (site_mod = &first; site_mod; site_mod = site_mod->next) {
-		bool init = system_state < SYSTEM_RUNNING;
-		struct module *mod = site_mod->mod;
-
-		if (!site_mod->sites) {
-			/*
-			 * This can happen if the static call key is defined in
-			 * a module which doesn't use it.
-			 *
-			 * It also happens in the has_mods case, where the
-			 * 'first' entry has no sites associated with it.
-			 */
-			continue;
-		}
-
-		stop = __stop_static_call_sites;
-
-		if (mod) {
-#ifdef CONFIG_MODULES
-			stop = mod->static_call_sites +
-			       mod->num_static_call_sites;
-			init = mod->state == MODULE_STATE_COMING;
-#endif
-		}
-
-		for (site = site_mod->sites;
-		     site < stop && static_call_key(site) == key; site++) {
-			void *site_addr = static_call_addr(site);
-
-			if (!init && static_call_is_init(site))
-				continue;
-
-			if (!kernel_text_address((unsigned long)site_addr)) {
-				/*
-				 * This skips patching built-in __exit, which
-				 * is part of init_section_contains() but is
-				 * not part of kernel_text_address().
-				 *
-				 * Skipping built-in __exit is fine since it
-				 * will never be executed.
-				 */
-				WARN_ONCE(!static_call_is_init(site),
-					  "can't patch static call site at %pS",
-					  site_addr);
-				continue;
-			}
-
-			arch_static_call_transform(site_addr, NULL, func,
-						   static_call_is_tail(site));
-		}
-	}
-
-done:
-	static_call_unlock();
-	cpus_read_unlock();
-}
-EXPORT_SYMBOL_GPL(__static_call_update);
-
-static int __static_call_init(struct module *mod,
-			      struct static_call_site *start,
-			      struct static_call_site *stop)
-{
-	struct static_call_site *site;
-	struct static_call_key *key, *prev_key = NULL;
-	struct static_call_mod *site_mod;
-
-	if (start == stop)
-		return 0;
-
-	static_call_sort_entries(start, stop);
-
-	for (site = start; site < stop; site++) {
-		void *site_addr = static_call_addr(site);
-
-		if ((mod && within_module_init((unsigned long)site_addr, mod)) ||
-		    (!mod && init_section_contains(site_addr, 1)))
-			static_call_set_init(site);
-
-		key = static_call_key(site);
-		if (key != prev_key) {
-			prev_key = key;
-
-			/*
-			 * For vmlinux (!mod) avoid the allocation by storing
-			 * the sites pointer in the key itself. Also see
-			 * __static_call_update()'s @first.
-			 *
-			 * This allows architectures (eg. x86) to call
-			 * static_call_init() before memory allocation works.
-			 */
-			if (!mod) {
-				key->sites = site;
-				key->type |= 1;
-				goto do_transform;
-			}
-
-			site_mod = kzalloc(sizeof(*site_mod), GFP_KERNEL);
-			if (!site_mod)
-				return -ENOMEM;
-
-			/*
-			 * When the key has a direct sites pointer, extract
-			 * that into an explicit struct static_call_mod, so we
-			 * can have a list of modules.
-			 */
-			if (static_call_key_sites(key)) {
-				site_mod->mod = NULL;
-				site_mod->next = NULL;
-				site_mod->sites = static_call_key_sites(key);
-
-				key->mods = site_mod;
-
-				site_mod = kzalloc(sizeof(*site_mod), GFP_KERNEL);
-				if (!site_mod)
-					return -ENOMEM;
-			}
-
-			site_mod->mod = mod;
-			site_mod->sites = site;
-			site_mod->next = static_call_key_next(key);
-			key->mods = site_mod;
-		}
-
-do_transform:
-		arch_static_call_transform(site_addr, NULL, key->func,
-				static_call_is_tail(site));
-	}
-
-	return 0;
-}
-
-static int addr_conflict(struct static_call_site *site, void *start, void *end)
-{
-	unsigned long addr = (unsigned long)static_call_addr(site);
-
-	if (addr <= (unsigned long)end &&
-	    addr + CALL_INSN_SIZE > (unsigned long)start)
-		return 1;
-
-	return 0;
-}
-
-static int __static_call_text_reserved(struct static_call_site *iter_start,
-				       struct static_call_site *iter_stop,
-				       void *start, void *end, bool init)
-{
-	struct static_call_site *iter = iter_start;
-
-	while (iter < iter_stop) {
-		if (init || !static_call_is_init(iter)) {
-			if (addr_conflict(iter, start, end))
-				return 1;
-		}
-		iter++;
-	}
-
-	return 0;
-}
-
-#ifdef CONFIG_MODULES
-
-static int __static_call_mod_text_reserved(void *start, void *end)
-{
-	struct module *mod;
-	int ret;
-
-	preempt_disable();
-	mod = __module_text_address((unsigned long)start);
-	WARN_ON_ONCE(__module_text_address((unsigned long)end) != mod);
-	if (!try_module_get(mod))
-		mod = NULL;
-	preempt_enable();
-
-	if (!mod)
-		return 0;
-
-	ret = __static_call_text_reserved(mod->static_call_sites,
-			mod->static_call_sites + mod->num_static_call_sites,
-			start, end, mod->state == MODULE_STATE_COMING);
-
-	module_put(mod);
-
-	return ret;
-}
-
-static unsigned long tramp_key_lookup(unsigned long addr)
-{
-	struct static_call_tramp_key *start = __start_static_call_tramp_key;
-	struct static_call_tramp_key *stop = __stop_static_call_tramp_key;
-	struct static_call_tramp_key *tramp_key;
-
-	for (tramp_key = start; tramp_key != stop; tramp_key++) {
-		unsigned long tramp;
-
-		tramp = (long)tramp_key->tramp + (long)&tramp_key->tramp;
-		if (tramp == addr)
-			return (long)tramp_key->key + (long)&tramp_key->key;
-	}
-
-	return 0;
-}
-
-static int static_call_add_module(struct module *mod)
-{
-	struct static_call_site *start = mod->static_call_sites;
-	struct static_call_site *stop = start + mod->num_static_call_sites;
-	struct static_call_site *site;
-
-	for (site = start; site != stop; site++) {
-		unsigned long s_key = __static_call_key(site);
-		unsigned long addr = s_key & ~STATIC_CALL_SITE_FLAGS;
-		unsigned long key;
-
-		/*
-		 * Is the key is exported, 'addr' points to the key, which
-		 * means modules are allowed to call static_call_update() on
-		 * it.
-		 *
-		 * Otherwise, the key isn't exported, and 'addr' points to the
-		 * trampoline so we need to lookup the key.
-		 *
-		 * We go through this dance to prevent crazy modules from
-		 * abusing sensitive static calls.
-		 */
-		if (!kernel_text_address(addr))
-			continue;
-
-		key = tramp_key_lookup(addr);
-		if (!key) {
-			pr_warn("Failed to fixup __raw_static_call() usage at: %ps\n",
-				static_call_addr(site));
-			return -EINVAL;
-		}
-
-		key |= s_key & STATIC_CALL_SITE_FLAGS;
-		site->key = key - (long)&site->key;
-	}
-
-	return __static_call_init(mod, start, stop);
-}
-
-static void static_call_del_module(struct module *mod)
-{
-	struct static_call_site *start = mod->static_call_sites;
-	struct static_call_site *stop = mod->static_call_sites +
-					mod->num_static_call_sites;
-	struct static_call_key *key, *prev_key = NULL;
-	struct static_call_mod *site_mod, **prev;
-	struct static_call_site *site;
-
-	for (site = start; site < stop; site++) {
-		key = static_call_key(site);
-		if (key == prev_key)
-			continue;
-
-		prev_key = key;
-
-		for (prev = &key->mods, site_mod = key->mods;
-		     site_mod && site_mod->mod != mod;
-		     prev = &site_mod->next, site_mod = site_mod->next)
-			;
-
-		if (!site_mod)
-			continue;
-
-		*prev = site_mod->next;
-		kfree(site_mod);
-	}
-}
-
-static int static_call_module_notify(struct notifier_block *nb,
-				     unsigned long val, void *data)
-{
-	struct module *mod = data;
-	int ret = 0;
-
-	cpus_read_lock();
-	static_call_lock();
-
-	switch (val) {
-	case MODULE_STATE_COMING:
-		ret = static_call_add_module(mod);
-		if (ret) {
-			WARN(1, "Failed to allocate memory for static calls");
-			static_call_del_module(mod);
-		}
-		break;
-	case MODULE_STATE_GOING:
-		static_call_del_module(mod);
-		break;
-	}
-
-	static_call_unlock();
-	cpus_read_unlock();
-
-	return notifier_from_errno(ret);
-}
-
-static struct notifier_block static_call_module_nb = {
-	.notifier_call = static_call_module_notify,
-};
-
-#else
-
-static inline int __static_call_mod_text_reserved(void *start, void *end)
-{
-	return 0;
-}
-
-#endif /* CONFIG_MODULES */
-
-int static_call_text_reserved(void *start, void *end)
-{
-	bool init = system_state < SYSTEM_RUNNING;
-	int ret = __static_call_text_reserved(__start_static_call_sites,
-			__stop_static_call_sites, start, end, init);
-
-	if (ret)
-		return ret;
-
-	return __static_call_mod_text_reserved(start, end);
-}
-
-int __init static_call_init(void)
-{
-	int ret;
-
-	if (static_call_initialized)
-		return 0;
-
-	cpus_read_lock();
-	static_call_lock();
-	ret = __static_call_init(NULL, __start_static_call_sites,
-				 __stop_static_call_sites);
-	static_call_unlock();
-	cpus_read_unlock();
-
-	if (ret) {
-		pr_err("Failed to allocate memory for static_call!\n");
-		BUG();
-	}
-
-	static_call_initialized = true;
-
-#ifdef CONFIG_MODULES
-	register_module_notifier(&static_call_module_nb);
-#endif
-	return 0;
-}
-early_initcall(static_call_init);
 
 long __static_call_return0(void)
 {
 	return 0;
 }
-
-#ifdef CONFIG_STATIC_CALL_SELFTEST
-
-static int func_a(int x)
-{
-	return x+1;
-}
-
-static int func_b(int x)
-{
-	return x+2;
-}
-
-DEFINE_STATIC_CALL(sc_selftest, func_a);
-
-static struct static_call_data {
-      int (*func)(int);
-      int val;
-      int expect;
-} static_call_data [] __initdata = {
-      { NULL,   2, 3 },
-      { func_b, 2, 4 },
-      { func_a, 2, 3 }
-};
-
-static int __init test_static_call_init(void)
-{
-      int i;
-
-      for (i = 0; i < ARRAY_SIZE(static_call_data); i++ ) {
-	      struct static_call_data *scd = &static_call_data[i];
-
-              if (scd->func)
-                      static_call_update(sc_selftest, scd->func);
-
-              WARN_ON(static_call(sc_selftest)(scd->val) != scd->expect);
-      }
-
-      return 0;
-}
-early_initcall(test_static_call_init);
-
-#endif /* CONFIG_STATIC_CALL_SELFTEST */
+EXPORT_SYMBOL_GPL(__static_call_return0);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/static_call_inline.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/static_call_inline.c
@@ -0,0 +1,554 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/static_call.h>
+#include <linux/bug.h>
+#include <linux/smp.h>
+#include <linux/sort.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/cpu.h>
+#include <linux/processor.h>
+#include <asm/sections.h>
+
+extern struct static_call_site __start_static_call_sites[],
+			       __stop_static_call_sites[];
+extern struct static_call_tramp_key __start_static_call_tramp_key[],
+				    __stop_static_call_tramp_key[];
+
+bool static_call_initialized;
+
+/* mutex to protect key modules/sites */
+static DEFINE_MUTEX(static_call_mutex);
+
+static void static_call_lock(void)
+{
+	mutex_lock(&static_call_mutex);
+}
+
+static void static_call_unlock(void)
+{
+	mutex_unlock(&static_call_mutex);
+}
+
+static inline void *static_call_addr(struct static_call_site *site)
+{
+	return (void *)((long)site->addr + (long)&site->addr);
+}
+
+static inline unsigned long __static_call_key(const struct static_call_site *site)
+{
+	return (long)site->key + (long)&site->key;
+}
+
+static inline struct static_call_key *static_call_key(const struct static_call_site *site)
+{
+	return (void *)(__static_call_key(site) & ~STATIC_CALL_SITE_FLAGS);
+}
+
+/* These assume the key is word-aligned. */
+static inline bool static_call_is_init(struct static_call_site *site)
+{
+	return __static_call_key(site) & STATIC_CALL_SITE_INIT;
+}
+
+static inline bool static_call_is_tail(struct static_call_site *site)
+{
+	return __static_call_key(site) & STATIC_CALL_SITE_TAIL;
+}
+
+static inline void static_call_set_init(struct static_call_site *site)
+{
+	site->key = (__static_call_key(site) | STATIC_CALL_SITE_INIT) -
+		    (long)&site->key;
+}
+
+static int static_call_site_cmp(const void *_a, const void *_b)
+{
+	const struct static_call_site *a = _a;
+	const struct static_call_site *b = _b;
+	const struct static_call_key *key_a = static_call_key(a);
+	const struct static_call_key *key_b = static_call_key(b);
+
+	if (key_a < key_b)
+		return -1;
+
+	if (key_a > key_b)
+		return 1;
+
+	return 0;
+}
+
+static void static_call_site_swap(void *_a, void *_b, int size)
+{
+	long delta = (unsigned long)_a - (unsigned long)_b;
+	struct static_call_site *a = _a;
+	struct static_call_site *b = _b;
+	struct static_call_site tmp = *a;
+
+	a->addr = b->addr  - delta;
+	a->key  = b->key   - delta;
+
+	b->addr = tmp.addr + delta;
+	b->key  = tmp.key  + delta;
+}
+
+static inline void static_call_sort_entries(struct static_call_site *start,
+					    struct static_call_site *stop)
+{
+	sort(start, stop - start, sizeof(struct static_call_site),
+	     static_call_site_cmp, static_call_site_swap);
+}
+
+static inline bool static_call_key_has_mods(struct static_call_key *key)
+{
+	return !(key->type & 1);
+}
+
+static inline struct static_call_mod *static_call_key_next(struct static_call_key *key)
+{
+	if (!static_call_key_has_mods(key))
+		return NULL;
+
+	return key->mods;
+}
+
+static inline struct static_call_site *static_call_key_sites(struct static_call_key *key)
+{
+	if (static_call_key_has_mods(key))
+		return NULL;
+
+	return (struct static_call_site *)(key->type & ~1);
+}
+
+void __static_call_update(struct static_call_key *key, void *tramp, void *func)
+{
+	struct static_call_site *site, *stop;
+	struct static_call_mod *site_mod, first;
+
+	cpus_read_lock();
+	static_call_lock();
+
+	if (key->func == func)
+		goto done;
+
+	key->func = func;
+
+	arch_static_call_transform(NULL, tramp, func, false);
+
+	/*
+	 * If uninitialized, we'll not update the callsites, but they still
+	 * point to the trampoline and we just patched that.
+	 */
+	if (WARN_ON_ONCE(!static_call_initialized))
+		goto done;
+
+	first = (struct static_call_mod){
+		.next = static_call_key_next(key),
+		.mod = NULL,
+		.sites = static_call_key_sites(key),
+	};
+
+	for (site_mod = &first; site_mod; site_mod = site_mod->next) {
+		bool init = system_state < SYSTEM_RUNNING;
+		struct module *mod = site_mod->mod;
+
+		if (!site_mod->sites) {
+			/*
+			 * This can happen if the static call key is defined in
+			 * a module which doesn't use it.
+			 *
+			 * It also happens in the has_mods case, where the
+			 * 'first' entry has no sites associated with it.
+			 */
+			continue;
+		}
+
+		stop = __stop_static_call_sites;
+
+		if (mod) {
+#ifdef CONFIG_MODULES
+			stop = mod->static_call_sites +
+			       mod->num_static_call_sites;
+			init = mod->state == MODULE_STATE_COMING;
+#endif
+		}
+
+		for (site = site_mod->sites;
+		     site < stop && static_call_key(site) == key; site++) {
+			void *site_addr = static_call_addr(site);
+
+			if (!init && static_call_is_init(site))
+				continue;
+
+			if (!kernel_text_address((unsigned long)site_addr)) {
+				/*
+				 * This skips patching built-in __exit, which
+				 * is part of init_section_contains() but is
+				 * not part of kernel_text_address().
+				 *
+				 * Skipping built-in __exit is fine since it
+				 * will never be executed.
+				 */
+				WARN_ONCE(!static_call_is_init(site),
+					  "can't patch static call site at %pS",
+					  site_addr);
+				continue;
+			}
+
+			arch_static_call_transform(site_addr, NULL, func,
+						   static_call_is_tail(site));
+		}
+	}
+
+done:
+	static_call_unlock();
+	cpus_read_unlock();
+}
+EXPORT_SYMBOL_GPL(__static_call_update);
+
+static int __static_call_init(struct module *mod,
+			      struct static_call_site *start,
+			      struct static_call_site *stop)
+{
+	struct static_call_site *site;
+	struct static_call_key *key, *prev_key = NULL;
+	struct static_call_mod *site_mod;
+
+	if (start == stop)
+		return 0;
+
+	static_call_sort_entries(start, stop);
+
+	for (site = start; site < stop; site++) {
+		void *site_addr = static_call_addr(site);
+
+		if ((mod && within_module_init((unsigned long)site_addr, mod)) ||
+		    (!mod && init_section_contains(site_addr, 1)))
+			static_call_set_init(site);
+
+		key = static_call_key(site);
+		if (key != prev_key) {
+			prev_key = key;
+
+			/*
+			 * For vmlinux (!mod) avoid the allocation by storing
+			 * the sites pointer in the key itself. Also see
+			 * __static_call_update()'s @first.
+			 *
+			 * This allows architectures (eg. x86) to call
+			 * static_call_init() before memory allocation works.
+			 */
+			if (!mod) {
+				key->sites = site;
+				key->type |= 1;
+				goto do_transform;
+			}
+
+			site_mod = kzalloc(sizeof(*site_mod), GFP_KERNEL);
+			if (!site_mod)
+				return -ENOMEM;
+
+			/*
+			 * When the key has a direct sites pointer, extract
+			 * that into an explicit struct static_call_mod, so we
+			 * can have a list of modules.
+			 */
+			if (static_call_key_sites(key)) {
+				site_mod->mod = NULL;
+				site_mod->next = NULL;
+				site_mod->sites = static_call_key_sites(key);
+
+				key->mods = site_mod;
+
+				site_mod = kzalloc(sizeof(*site_mod), GFP_KERNEL);
+				if (!site_mod)
+					return -ENOMEM;
+			}
+
+			site_mod->mod = mod;
+			site_mod->sites = site;
+			site_mod->next = static_call_key_next(key);
+			key->mods = site_mod;
+		}
+
+do_transform:
+		arch_static_call_transform(site_addr, NULL, key->func,
+				static_call_is_tail(site));
+	}
+
+	return 0;
+}
+
+static int addr_conflict(struct static_call_site *site, void *start, void *end)
+{
+	unsigned long addr = (unsigned long)static_call_addr(site);
+
+	if (addr <= (unsigned long)end &&
+	    addr + CALL_INSN_SIZE > (unsigned long)start)
+		return 1;
+
+	return 0;
+}
+
+static int __static_call_text_reserved(struct static_call_site *iter_start,
+				       struct static_call_site *iter_stop,
+				       void *start, void *end, bool init)
+{
+	struct static_call_site *iter = iter_start;
+
+	while (iter < iter_stop) {
+		if (init || !static_call_is_init(iter)) {
+			if (addr_conflict(iter, start, end))
+				return 1;
+		}
+		iter++;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_MODULES
+
+static int __static_call_mod_text_reserved(void *start, void *end)
+{
+	struct module *mod;
+	int ret;
+
+	preempt_disable();
+	mod = __module_text_address((unsigned long)start);
+	WARN_ON_ONCE(__module_text_address((unsigned long)end) != mod);
+	if (!try_module_get(mod))
+		mod = NULL;
+	preempt_enable();
+
+	if (!mod)
+		return 0;
+
+	ret = __static_call_text_reserved(mod->static_call_sites,
+			mod->static_call_sites + mod->num_static_call_sites,
+			start, end, mod->state == MODULE_STATE_COMING);
+
+	module_put(mod);
+
+	return ret;
+}
+
+static unsigned long tramp_key_lookup(unsigned long addr)
+{
+	struct static_call_tramp_key *start = __start_static_call_tramp_key;
+	struct static_call_tramp_key *stop = __stop_static_call_tramp_key;
+	struct static_call_tramp_key *tramp_key;
+
+	for (tramp_key = start; tramp_key != stop; tramp_key++) {
+		unsigned long tramp;
+
+		tramp = (long)tramp_key->tramp + (long)&tramp_key->tramp;
+		if (tramp == addr)
+			return (long)tramp_key->key + (long)&tramp_key->key;
+	}
+
+	return 0;
+}
+
+static int static_call_add_module(struct module *mod)
+{
+	struct static_call_site *start = mod->static_call_sites;
+	struct static_call_site *stop = start + mod->num_static_call_sites;
+	struct static_call_site *site;
+
+	for (site = start; site != stop; site++) {
+		unsigned long s_key = __static_call_key(site);
+		unsigned long addr = s_key & ~STATIC_CALL_SITE_FLAGS;
+		unsigned long key;
+
+		/*
+		 * Is the key is exported, 'addr' points to the key, which
+		 * means modules are allowed to call static_call_update() on
+		 * it.
+		 *
+		 * Otherwise, the key isn't exported, and 'addr' points to the
+		 * trampoline so we need to lookup the key.
+		 *
+		 * We go through this dance to prevent crazy modules from
+		 * abusing sensitive static calls.
+		 */
+		if (!kernel_text_address(addr))
+			continue;
+
+		key = tramp_key_lookup(addr);
+		if (!key) {
+			pr_warn("Failed to fixup __raw_static_call() usage at: %ps\n",
+				static_call_addr(site));
+			return -EINVAL;
+		}
+
+		key |= s_key & STATIC_CALL_SITE_FLAGS;
+		site->key = key - (long)&site->key;
+	}
+
+	return __static_call_init(mod, start, stop);
+}
+
+static void static_call_del_module(struct module *mod)
+{
+	struct static_call_site *start = mod->static_call_sites;
+	struct static_call_site *stop = mod->static_call_sites +
+					mod->num_static_call_sites;
+	struct static_call_key *key, *prev_key = NULL;
+	struct static_call_mod *site_mod, **prev;
+	struct static_call_site *site;
+
+	for (site = start; site < stop; site++) {
+		key = static_call_key(site);
+
+		/*
+		 * If the key was not updated due to a memory allocation
+		 * failure in __static_call_init() then treating key::sites
+		 * as key::mods in the code below would cause random memory
+		 * access and #GP. In that case all subsequent sites have
+		 * not been touched either, so stop iterating.
+		 */
+		if (!static_call_key_has_mods(key))
+			break;
+
+		if (key == prev_key)
+			continue;
+
+		prev_key = key;
+
+		for (prev = &key->mods, site_mod = key->mods;
+		     site_mod && site_mod->mod != mod;
+		     prev = &site_mod->next, site_mod = site_mod->next)
+			;
+
+		if (!site_mod)
+			continue;
+
+		*prev = site_mod->next;
+		kfree(site_mod);
+	}
+}
+
+static int static_call_module_notify(struct notifier_block *nb,
+				     unsigned long val, void *data)
+{
+	struct module *mod = data;
+	int ret = 0;
+
+	cpus_read_lock();
+	static_call_lock();
+
+	switch (val) {
+	case MODULE_STATE_COMING:
+		ret = static_call_add_module(mod);
+		if (ret) {
+			pr_warn("Failed to allocate memory for static calls\n");
+			static_call_del_module(mod);
+		}
+		break;
+	case MODULE_STATE_GOING:
+		static_call_del_module(mod);
+		break;
+	}
+
+	static_call_unlock();
+	cpus_read_unlock();
+
+	return notifier_from_errno(ret);
+}
+
+static struct notifier_block static_call_module_nb = {
+	.notifier_call = static_call_module_notify,
+};
+
+#else
+
+static inline int __static_call_mod_text_reserved(void *start, void *end)
+{
+	return 0;
+}
+
+#endif /* CONFIG_MODULES */
+
+int static_call_text_reserved(void *start, void *end)
+{
+	bool init = system_state < SYSTEM_RUNNING;
+	int ret = __static_call_text_reserved(__start_static_call_sites,
+			__stop_static_call_sites, start, end, init);
+
+	if (ret)
+		return ret;
+
+	return __static_call_mod_text_reserved(start, end);
+}
+
+int __init static_call_init(void)
+{
+	int ret;
+
+	if (static_call_initialized)
+		return 0;
+
+	cpus_read_lock();
+	static_call_lock();
+	ret = __static_call_init(NULL, __start_static_call_sites,
+				 __stop_static_call_sites);
+	static_call_unlock();
+	cpus_read_unlock();
+
+	if (ret) {
+		pr_err("Failed to allocate memory for static_call!\n");
+		BUG();
+	}
+
+	static_call_initialized = true;
+
+#ifdef CONFIG_MODULES
+	register_module_notifier(&static_call_module_nb);
+#endif
+	return 0;
+}
+early_initcall(static_call_init);
+
+#ifdef CONFIG_STATIC_CALL_SELFTEST
+
+static int func_a(int x)
+{
+	return x+1;
+}
+
+static int func_b(int x)
+{
+	return x+2;
+}
+
+DEFINE_STATIC_CALL(sc_selftest, func_a);
+
+static struct static_call_data {
+      int (*func)(int);
+      int val;
+      int expect;
+} static_call_data [] __initdata = {
+      { NULL,   2, 3 },
+      { func_b, 2, 4 },
+      { func_a, 2, 3 }
+};
+
+static int __init test_static_call_init(void)
+{
+      int i;
+
+      for (i = 0; i < ARRAY_SIZE(static_call_data); i++ ) {
+	      struct static_call_data *scd = &static_call_data[i];
+
+              if (scd->func)
+                      static_call_update(sc_selftest, scd->func);
+
+              WARN_ON(static_call(sc_selftest)(scd->val) != scd->expect);
+      }
+
+      return 0;
+}
+early_initcall(test_static_call_init);
+
+#endif /* CONFIG_STATIC_CALL_SELFTEST */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sys.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sys.c
@@ -472,6 +472,16 @@
 	if (!new_user)
 		return -EAGAIN;
 
+	free_uid(new->user);
+	new->user = new_user;
+	return 0;
+}
+
+static void flag_nproc_exceeded(struct cred *new)
+{
+	if (new->ucounts == current_ucounts())
+		return;
+
 	/*
 	 * We don't fail in case of NPROC limit excess here because too many
 	 * poorly written programs don't check set*uid() return code, assuming
@@ -480,15 +490,10 @@
 	 * failure to the execve() stage.
 	 */
 	if (is_ucounts_overlimit(new->ucounts, UCOUNT_RLIMIT_NPROC, rlimit(RLIMIT_NPROC)) &&
-			new_user != INIT_USER &&
-			!capable(CAP_SYS_RESOURCE) && !capable(CAP_SYS_ADMIN))
+			new->user != INIT_USER)
 		current->flags |= PF_NPROC_EXCEEDED;
 	else
 		current->flags &= ~PF_NPROC_EXCEEDED;
-
-	free_uid(new->user);
-	new->user = new_user;
-	return 0;
 }
 
 /*
@@ -563,6 +568,7 @@
 	if (retval < 0)
 		goto error;
 
+	flag_nproc_exceeded(new);
 	return commit_creds(new);
 
 error:
@@ -625,6 +631,7 @@
 	if (retval < 0)
 		goto error;
 
+	flag_nproc_exceeded(new);
 	return commit_creds(new);
 
 error:
@@ -649,6 +656,7 @@
 	struct cred *new;
 	int retval;
 	kuid_t kruid, keuid, ksuid;
+	bool ruid_new, euid_new, suid_new;
 
 	kruid = make_kuid(ns, ruid);
 	keuid = make_kuid(ns, euid);
@@ -663,25 +671,29 @@
 	if ((suid != (uid_t) -1) && !uid_valid(ksuid))
 		return -EINVAL;
 
+	old = current_cred();
+
+	/* check for no-op */
+	if ((ruid == (uid_t) -1 || uid_eq(kruid, old->uid)) &&
+	    (euid == (uid_t) -1 || (uid_eq(keuid, old->euid) &&
+				    uid_eq(keuid, old->fsuid))) &&
+	    (suid == (uid_t) -1 || uid_eq(ksuid, old->suid)))
+		return 0;
+
+	ruid_new = ruid != (uid_t) -1        && !uid_eq(kruid, old->uid) &&
+		   !uid_eq(kruid, old->euid) && !uid_eq(kruid, old->suid);
+	euid_new = euid != (uid_t) -1        && !uid_eq(keuid, old->uid) &&
+		   !uid_eq(keuid, old->euid) && !uid_eq(keuid, old->suid);
+	suid_new = suid != (uid_t) -1        && !uid_eq(ksuid, old->uid) &&
+		   !uid_eq(ksuid, old->euid) && !uid_eq(ksuid, old->suid);
+	if ((ruid_new || euid_new || suid_new) &&
+	    !ns_capable_setid(old->user_ns, CAP_SETUID))
+		return -EPERM;
+
 	new = prepare_creds();
 	if (!new)
 		return -ENOMEM;
 
-	old = current_cred();
-
-	retval = -EPERM;
-	if (!ns_capable_setid(old->user_ns, CAP_SETUID)) {
-		if (ruid != (uid_t) -1        && !uid_eq(kruid, old->uid) &&
-		    !uid_eq(kruid, old->euid) && !uid_eq(kruid, old->suid))
-			goto error;
-		if (euid != (uid_t) -1        && !uid_eq(keuid, old->uid) &&
-		    !uid_eq(keuid, old->euid) && !uid_eq(keuid, old->suid))
-			goto error;
-		if (suid != (uid_t) -1        && !uid_eq(ksuid, old->uid) &&
-		    !uid_eq(ksuid, old->euid) && !uid_eq(ksuid, old->suid))
-			goto error;
-	}
-
 	if (ruid != (uid_t) -1) {
 		new->uid = kruid;
 		if (!uid_eq(kruid, old->uid)) {
@@ -704,6 +716,7 @@
 	if (retval < 0)
 		goto error;
 
+	flag_nproc_exceeded(new);
 	return commit_creds(new);
 
 error:
@@ -745,6 +758,7 @@
 	struct cred *new;
 	int retval;
 	kgid_t krgid, kegid, ksgid;
+	bool rgid_new, egid_new, sgid_new;
 
 	krgid = make_kgid(ns, rgid);
 	kegid = make_kgid(ns, egid);
@@ -757,23 +771,28 @@
 	if ((sgid != (gid_t) -1) && !gid_valid(ksgid))
 		return -EINVAL;
 
+	old = current_cred();
+
+	/* check for no-op */
+	if ((rgid == (gid_t) -1 || gid_eq(krgid, old->gid)) &&
+	    (egid == (gid_t) -1 || (gid_eq(kegid, old->egid) &&
+				    gid_eq(kegid, old->fsgid))) &&
+	    (sgid == (gid_t) -1 || gid_eq(ksgid, old->sgid)))
+		return 0;
+
+	rgid_new = rgid != (gid_t) -1        && !gid_eq(krgid, old->gid) &&
+		   !gid_eq(krgid, old->egid) && !gid_eq(krgid, old->sgid);
+	egid_new = egid != (gid_t) -1        && !gid_eq(kegid, old->gid) &&
+		   !gid_eq(kegid, old->egid) && !gid_eq(kegid, old->sgid);
+	sgid_new = sgid != (gid_t) -1        && !gid_eq(ksgid, old->gid) &&
+		   !gid_eq(ksgid, old->egid) && !gid_eq(ksgid, old->sgid);
+	if ((rgid_new || egid_new || sgid_new) &&
+	    !ns_capable_setid(old->user_ns, CAP_SETGID))
+		return -EPERM;
+
 	new = prepare_creds();
 	if (!new)
 		return -ENOMEM;
-	old = current_cred();
-
-	retval = -EPERM;
-	if (!ns_capable_setid(old->user_ns, CAP_SETGID)) {
-		if (rgid != (gid_t) -1        && !gid_eq(krgid, old->gid) &&
-		    !gid_eq(krgid, old->egid) && !gid_eq(krgid, old->sgid))
-			goto error;
-		if (egid != (gid_t) -1        && !gid_eq(kegid, old->gid) &&
-		    !gid_eq(kegid, old->egid) && !gid_eq(kegid, old->sgid))
-			goto error;
-		if (sgid != (gid_t) -1        && !gid_eq(ksgid, old->gid) &&
-		    !gid_eq(ksgid, old->egid) && !gid_eq(ksgid, old->sgid))
-			goto error;
-	}
 
 	if (rgid != (gid_t) -1)
 		new->gid = krgid;
@@ -1229,6 +1248,21 @@
 DECLARE_RWSEM(uts_sem);
 
 #ifdef COMPAT_UTS_MACHINE
+static char compat_uts_machine[__OLD_UTS_LEN+1] = COMPAT_UTS_MACHINE;
+
+static int __init parse_compat_uts_machine(char *arg)
+{
+	strncpy(compat_uts_machine, arg, __OLD_UTS_LEN);
+	compat_uts_machine[__OLD_UTS_LEN] = 0;
+	return 0;
+}
+early_param("compat_uts_machine", parse_compat_uts_machine);
+
+#undef COMPAT_UTS_MACHINE
+#define COMPAT_UTS_MACHINE compat_uts_machine
+#endif
+
+#ifdef COMPAT_UTS_MACHINE
 #define override_architecture(name) \
 	(personality(current->personality) == PER_LINUX32 && \
 	 copy_to_user(name->machine, COMPAT_UTS_MACHINE, \
@@ -1567,6 +1601,8 @@
 
 	if (resource >= RLIM_NLIMITS)
 		return -EINVAL;
+	resource = array_index_nospec(resource, RLIM_NLIMITS);
+
 	if (new_rlim) {
 		if (new_rlim->rlim_cur > new_rlim->rlim_max)
 			return -EINVAL;
@@ -1742,74 +1778,87 @@
 	struct task_struct *t;
 	unsigned long flags;
 	u64 tgutime, tgstime, utime, stime;
-	unsigned long maxrss = 0;
+	unsigned long maxrss;
+	struct mm_struct *mm;
+	struct signal_struct *sig = p->signal;
+	unsigned int seq = 0;
 
-	memset((char *)r, 0, sizeof (*r));
+retry:
+	memset(r, 0, sizeof(*r));
 	utime = stime = 0;
+	maxrss = 0;
 
 	if (who == RUSAGE_THREAD) {
 		task_cputime_adjusted(current, &utime, &stime);
 		accumulate_thread_rusage(p, r);
-		maxrss = p->signal->maxrss;
-		goto out;
+		maxrss = sig->maxrss;
+		goto out_thread;
 	}
 
-	if (!lock_task_sighand(p, &flags))
-		return;
+	flags = read_seqbegin_or_lock_irqsave(&sig->stats_lock, &seq);
 
 	switch (who) {
 	case RUSAGE_BOTH:
 	case RUSAGE_CHILDREN:
-		utime = p->signal->cutime;
-		stime = p->signal->cstime;
-		r->ru_nvcsw = p->signal->cnvcsw;
-		r->ru_nivcsw = p->signal->cnivcsw;
-		r->ru_minflt = p->signal->cmin_flt;
-		r->ru_majflt = p->signal->cmaj_flt;
-		r->ru_inblock = p->signal->cinblock;
-		r->ru_oublock = p->signal->coublock;
-		maxrss = p->signal->cmaxrss;
+		utime = sig->cutime;
+		stime = sig->cstime;
+		r->ru_nvcsw = sig->cnvcsw;
+		r->ru_nivcsw = sig->cnivcsw;
+		r->ru_minflt = sig->cmin_flt;
+		r->ru_majflt = sig->cmaj_flt;
+		r->ru_inblock = sig->cinblock;
+		r->ru_oublock = sig->coublock;
+		maxrss = sig->cmaxrss;
 
 		if (who == RUSAGE_CHILDREN)
 			break;
 		fallthrough;
 
 	case RUSAGE_SELF:
-		thread_group_cputime_adjusted(p, &tgutime, &tgstime);
-		utime += tgutime;
-		stime += tgstime;
-		r->ru_nvcsw += p->signal->nvcsw;
-		r->ru_nivcsw += p->signal->nivcsw;
-		r->ru_minflt += p->signal->min_flt;
-		r->ru_majflt += p->signal->maj_flt;
-		r->ru_inblock += p->signal->inblock;
-		r->ru_oublock += p->signal->oublock;
-		if (maxrss < p->signal->maxrss)
-			maxrss = p->signal->maxrss;
-		t = p;
-		do {
+		r->ru_nvcsw += sig->nvcsw;
+		r->ru_nivcsw += sig->nivcsw;
+		r->ru_minflt += sig->min_flt;
+		r->ru_majflt += sig->maj_flt;
+		r->ru_inblock += sig->inblock;
+		r->ru_oublock += sig->oublock;
+		if (maxrss < sig->maxrss)
+			maxrss = sig->maxrss;
+
+		rcu_read_lock();
+		__for_each_thread(sig, t)
 			accumulate_thread_rusage(t, r);
-		} while_each_thread(p, t);
+		rcu_read_unlock();
+
 		break;
 
 	default:
 		BUG();
 	}
-	unlock_task_sighand(p, &flags);
 
-out:
-	r->ru_utime = ns_to_kernel_old_timeval(utime);
-	r->ru_stime = ns_to_kernel_old_timeval(stime);
+	if (need_seqretry(&sig->stats_lock, seq)) {
+		seq = 1;
+		goto retry;
+	}
+	done_seqretry_irqrestore(&sig->stats_lock, seq, flags);
 
-	if (who != RUSAGE_CHILDREN) {
-		struct mm_struct *mm = get_task_mm(p);
+	if (who == RUSAGE_CHILDREN)
+		goto out_children;
 
-		if (mm) {
-			setmax_mm_hiwater_rss(&maxrss, mm);
-			mmput(mm);
-		}
+	thread_group_cputime_adjusted(p, &tgutime, &tgstime);
+	utime += tgutime;
+	stime += tgstime;
+
+out_thread:
+	mm = get_task_mm(p);
+	if (mm) {
+		setmax_mm_hiwater_rss(&maxrss, mm);
+		mmput(mm);
 	}
+
+out_children:
 	r->ru_maxrss = maxrss * (PAGE_SIZE / 1024); /* convert pages to KBs */
+	r->ru_utime = ns_to_kernel_old_timeval(utime);
+	r->ru_stime = ns_to_kernel_old_timeval(stime);
 }
 
 SYSCALL_DEFINE2(getrusage, int, who, struct rusage __user *, ru)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sys_ni.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sys_ni.c
@@ -46,8 +46,8 @@
 COND_SYSCALL(io_getevents);
 COND_SYSCALL(io_pgetevents_time32);
 COND_SYSCALL(io_pgetevents);
-COND_SYSCALL_COMPAT(io_pgetevents_time32);
 COND_SYSCALL_COMPAT(io_pgetevents);
+COND_SYSCALL_COMPAT(io_pgetevents_time64);
 COND_SYSCALL(io_uring_setup);
 COND_SYSCALL(io_uring_enter);
 COND_SYSCALL(io_uring_register);
@@ -276,6 +276,7 @@
 
 /* mm/fadvise.c */
 COND_SYSCALL(fadvise64_64);
+COND_SYSCALL_COMPAT(fadvise64_64);
 
 /* mm/, CONFIG_MMU only */
 COND_SYSCALL(swapon);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/sysctl.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/sysctl.c
@@ -73,6 +73,7 @@
 #include <linux/latencytop.h>
 #include <linux/pid.h>
 #include <linux/delayacct.h>
+#include <linux/user_namespace.h>
 
 #include "../lib/kstrtox.h"
 
@@ -113,40 +114,23 @@
 static int sixty = 60;
 #endif
 
-static int __maybe_unused neg_one = -1;
-static int __maybe_unused two = 2;
-static int __maybe_unused four = 4;
-static unsigned long zero_ul;
-static unsigned long one_ul = 1;
-static unsigned long long_max = LONG_MAX;
-static int one_hundred = 100;
-static int two_hundred = 200;
-static int one_thousand = 1000;
 #ifdef CONFIG_PRINTK
-static int ten_thousand = 10000;
+static const int ten_thousand = 10000;
 #endif
 #ifdef CONFIG_PERF_EVENTS
-static int six_hundred_forty_kb = 640 * 1024;
+static const int six_hundred_forty_kb = 640 * 1024;
 #endif
 
 /* this is needed for the proc_doulongvec_minmax of vm_dirty_bytes */
-static unsigned long dirty_bytes_min = 2 * PAGE_SIZE;
+static const unsigned long dirty_bytes_min = 2 * PAGE_SIZE;
 
 /* this is needed for the proc_dointvec_minmax for [fs_]overflow UID and GID */
-static int maxolduid = 65535;
-static int minolduid;
+static const int maxolduid = 65535;
+static const int minolduid;
 
 static int ngroups_max = NGROUPS_MAX;
 static const int cap_last_cap = CAP_LAST_CAP;
 
-/*
- * This is needed for proc_doulongvec_minmax of sysctl_hung_task_timeout_secs
- * and hung_task_check_interval_secs
- */
-#ifdef CONFIG_DETECT_HUNG_TASK
-static unsigned long hung_task_timeout_max = (LONG_MAX/HZ);
-#endif
-
 #ifdef CONFIG_INOTIFY_USER
 #include <linux/inotify.h>
 #endif
@@ -190,8 +174,8 @@
 #endif
 
 #ifdef CONFIG_COMPACTION
-static int min_extfrag_threshold;
-static int max_extfrag_threshold = 1000;
+static const int min_extfrag_threshold;
+static const int max_extfrag_threshold = 1000;
 #endif
 
 #endif /* CONFIG_SYSCTL */
@@ -228,6 +212,10 @@
 	return ret;
 }
 
+void __weak unpriv_ebpf_notify(int new_state)
+{
+}
+
 static int bpf_unpriv_handler(struct ctl_table *table, int write,
 			      void *buffer, size_t *lenp, loff_t *ppos)
 {
@@ -245,6 +233,9 @@
 			return -EPERM;
 		*(int *)table->data = unpriv_enable;
 	}
+
+	unpriv_ebpf_notify(unpriv_enable);
+
 	return ret;
 }
 #endif /* CONFIG_BPF_SYSCALL && CONFIG_SYSCTL */
@@ -378,13 +369,14 @@
 			ppos);
 }
 
-static size_t proc_skip_spaces(char **buf)
+static void proc_skip_spaces(char **buf, size_t *size)
 {
-	size_t ret;
-	char *tmp = skip_spaces(*buf);
-	ret = tmp - *buf;
-	*buf = tmp;
-	return ret;
+	while (*size) {
+		if (!isspace(**buf))
+			break;
+		(*size)--;
+		(*buf)++;
+	}
 }
 
 static void proc_skip_char(char **buf, size_t *size, const char v)
@@ -453,13 +445,12 @@
 			  unsigned long *val, bool *neg,
 			  const char *perm_tr, unsigned perm_tr_len, char *tr)
 {
-	int len;
 	char *p, tmp[TMPBUFLEN];
+	ssize_t len = *size;
 
-	if (!*size)
+	if (len <= 0)
 		return -EINVAL;
 
-	len = *size;
 	if (len > TMPBUFLEN - 1)
 		len = TMPBUFLEN - 1;
 
@@ -559,14 +550,14 @@
 		if (*negp) {
 			if (*lvalp > (unsigned long) INT_MAX + 1)
 				return -EINVAL;
-			*valp = -*lvalp;
+			WRITE_ONCE(*valp, -*lvalp);
 		} else {
 			if (*lvalp > (unsigned long) INT_MAX)
 				return -EINVAL;
-			*valp = *lvalp;
+			WRITE_ONCE(*valp, *lvalp);
 		}
 	} else {
-		int val = *valp;
+		int val = READ_ONCE(*valp);
 		if (val < 0) {
 			*negp = true;
 			*lvalp = -(unsigned long)val;
@@ -585,9 +576,9 @@
 	if (write) {
 		if (*lvalp > UINT_MAX)
 			return -EINVAL;
-		*valp = *lvalp;
+		WRITE_ONCE(*valp, *lvalp);
 	} else {
-		unsigned int val = *valp;
+		unsigned int val = READ_ONCE(*valp);
 		*lvalp = (unsigned long)val;
 	}
 	return 0;
@@ -632,7 +623,7 @@
 		bool neg;
 
 		if (write) {
-			left -= proc_skip_spaces(&p);
+			proc_skip_spaces(&p, &left);
 
 			if (!left)
 				break;
@@ -659,7 +650,7 @@
 	if (!write && !first && left && !err)
 		proc_put_char(&buffer, &left, '\n');
 	if (write && !err && left)
-		left -= proc_skip_spaces(&p);
+		proc_skip_spaces(&p, &left);
 	if (write && first)
 		return err ? : -EINVAL;
 	*lenp -= left;
@@ -701,7 +692,7 @@
 	if (left > PAGE_SIZE - 1)
 		left = PAGE_SIZE - 1;
 
-	left -= proc_skip_spaces(&p);
+	proc_skip_spaces(&p, &left);
 	if (!left) {
 		err = -EINVAL;
 		goto out_free;
@@ -721,7 +712,7 @@
 	}
 
 	if (!err && left)
-		left -= proc_skip_spaces(&p);
+		proc_skip_spaces(&p, &left);
 
 out_free:
 	if (err)
@@ -981,7 +972,7 @@
 		if ((param->min && *param->min > tmp) ||
 		    (param->max && *param->max < tmp))
 			return -EINVAL;
-		*valp = tmp;
+		WRITE_ONCE(*valp, tmp);
 	}
 
 	return 0;
@@ -1047,7 +1038,7 @@
 		    (param->max && *param->max < tmp))
 			return -ERANGE;
 
-		*valp = tmp;
+		WRITE_ONCE(*valp, tmp);
 	}
 
 	return 0;
@@ -1131,13 +1122,13 @@
 
 	tmp.maxlen = sizeof(val);
 	tmp.data = &val;
-	val = *data;
+	val = READ_ONCE(*data);
 	res = do_proc_douintvec(&tmp, write, buffer, lenp, ppos,
 				do_proc_douintvec_minmax_conv, &param);
 	if (res)
 		return res;
 	if (write)
-		*data = val;
+		WRITE_ONCE(*data, val);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(proc_dou8vec_minmax);
@@ -1258,7 +1249,7 @@
 		if (write) {
 			bool neg;
 
-			left -= proc_skip_spaces(&p);
+			proc_skip_spaces(&p, &left);
 			if (!left)
 				break;
 
@@ -1274,9 +1265,9 @@
 				err = -EINVAL;
 				break;
 			}
-			*i = val;
+			WRITE_ONCE(*i, val);
 		} else {
-			val = convdiv * (*i) / convmul;
+			val = convdiv * READ_ONCE(*i) / convmul;
 			if (!first)
 				proc_put_char(&buffer, &left, '\t');
 			proc_put_long(&buffer, &left, val, false);
@@ -1286,7 +1277,7 @@
 	if (!write && !first && left && !err)
 		proc_put_char(&buffer, &left, '\n');
 	if (write && !err)
-		left -= proc_skip_spaces(&p);
+		proc_skip_spaces(&p, &left);
 	if (write && first)
 		return err ? : -EINVAL;
 	*lenp -= left;
@@ -1357,9 +1348,12 @@
 	if (write) {
 		if (*lvalp > INT_MAX / HZ)
 			return 1;
-		*valp = *negp ? -(*lvalp*HZ) : (*lvalp*HZ);
+		if (*negp)
+			WRITE_ONCE(*valp, -*lvalp * HZ);
+		else
+			WRITE_ONCE(*valp, *lvalp * HZ);
 	} else {
-		int val = *valp;
+		int val = READ_ONCE(*valp);
 		unsigned long lval;
 		if (val < 0) {
 			*negp = true;
@@ -1405,9 +1399,9 @@
 
 		if (jif > INT_MAX)
 			return 1;
-		*valp = (int)jif;
+		WRITE_ONCE(*valp, (int)jif);
 	} else {
-		int val = *valp;
+		int val = READ_ONCE(*valp);
 		unsigned long lval;
 		if (val < 0) {
 			*negp = true;
@@ -1475,8 +1469,8 @@
  * @ppos: the current position in the file
  *
  * Reads/writes up to table->maxlen/sizeof(unsigned int) integer
- * values from/to the user buffer, treated as an ASCII string. 
- * The values read are assumed to be in 1/1000 seconds, and 
+ * values from/to the user buffer, treated as an ASCII string.
+ * The values read are assumed to be in 1/1000 seconds, and
  * are converted into jiffies.
  *
  * Returns 0 on success.
@@ -1817,6 +1811,8 @@
 		.maxlen		= sizeof(unsigned int),
 		.mode		= 0644,
 		.proc_handler	= sched_rt_handler,
+		.extra1		= SYSCTL_ONE,
+		.extra2		= SYSCTL_INT_MAX,
 	},
 	{
 		.procname	= "sched_rt_runtime_us",
@@ -1824,6 +1820,8 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= sched_rt_handler,
+		.extra1		= SYSCTL_NEG_ONE,
+		.extra2		= SYSCTL_INT_MAX,
 	},
 	{
 		.procname	= "sched_deadline_period_max_us",
@@ -1949,6 +1947,15 @@
 		.proc_handler	= proc_dointvec,
 	},
 #endif
+#ifdef CONFIG_USER_NS
+	{
+		.procname	= "unprivileged_userns_clone",
+		.data		= &unprivileged_userns_clone,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec,
+	},
+#endif
 #ifdef CONFIG_PROC_SYSCTL
 	{
 		.procname	= "tainted",
@@ -1962,7 +1969,7 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &neg_one,
+		.extra1		= SYSCTL_NEG_ONE,
 		.extra2		= SYSCTL_ONE,
 	},
 #endif
@@ -2195,8 +2202,8 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &minolduid,
-		.extra2		= &maxolduid,
+		.extra1		= (void *)&minolduid,
+		.extra2		= (void *)&maxolduid,
 	},
 	{
 		.procname	= "overflowgid",
@@ -2204,8 +2211,8 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &minolduid,
-		.extra2		= &maxolduid,
+		.extra1		= (void *)&minolduid,
+		.extra2		= (void *)&maxolduid,
 	},
 #ifdef CONFIG_S390
 	{
@@ -2216,17 +2223,6 @@
 		.proc_handler	= proc_dointvec,
 	},
 #endif
-#ifdef CONFIG_SMP
-	{
-		.procname	= "oops_all_cpu_backtrace",
-		.data		= &sysctl_oops_all_cpu_backtrace,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= SYSCTL_ZERO,
-		.extra2		= SYSCTL_ONE,
-	},
-#endif /* CONFIG_SMP */
 	{
 		.procname	= "pid_max",
 		.data		= &pid_max,
@@ -2279,7 +2275,7 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &ten_thousand,
+		.extra2		= (void *)&ten_thousand,
 	},
 	{
 		.procname	= "printk_devkmsg",
@@ -2304,7 +2300,7 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax_sysadmin,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 #endif
 	{
@@ -2513,60 +2509,6 @@
 		.proc_handler	= proc_dointvec,
 	},
 #endif
-#ifdef CONFIG_DETECT_HUNG_TASK
-#ifdef CONFIG_SMP
-	{
-		.procname	= "hung_task_all_cpu_backtrace",
-		.data		= &sysctl_hung_task_all_cpu_backtrace,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= SYSCTL_ZERO,
-		.extra2		= SYSCTL_ONE,
-	},
-#endif /* CONFIG_SMP */
-	{
-		.procname	= "hung_task_panic",
-		.data		= &sysctl_hung_task_panic,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= SYSCTL_ZERO,
-		.extra2		= SYSCTL_ONE,
-	},
-	{
-		.procname	= "hung_task_check_count",
-		.data		= &sysctl_hung_task_check_count,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= SYSCTL_ZERO,
-	},
-	{
-		.procname	= "hung_task_timeout_secs",
-		.data		= &sysctl_hung_task_timeout_secs,
-		.maxlen		= sizeof(unsigned long),
-		.mode		= 0644,
-		.proc_handler	= proc_dohung_task_timeout_secs,
-		.extra2		= &hung_task_timeout_max,
-	},
-	{
-		.procname	= "hung_task_check_interval_secs",
-		.data		= &sysctl_hung_task_check_interval_secs,
-		.maxlen		= sizeof(unsigned long),
-		.mode		= 0644,
-		.proc_handler	= proc_dohung_task_timeout_secs,
-		.extra2		= &hung_task_timeout_max,
-	},
-	{
-		.procname	= "hung_task_warnings",
-		.data		= &sysctl_hung_task_warnings,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &neg_one,
-	},
-#endif
 #ifdef CONFIG_RT_MUTEXES
 	{
 		.procname	= "max_lock_depth",
@@ -2626,7 +2568,7 @@
 		.mode		= 0644,
 		.proc_handler	= perf_cpu_time_max_percent_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= SYSCTL_ONE_HUNDRED,
 	},
 	{
 		.procname	= "perf_event_max_stack",
@@ -2635,7 +2577,7 @@
 		.mode		= 0644,
 		.proc_handler	= perf_event_max_stack_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &six_hundred_forty_kb,
+		.extra2		= (void *)&six_hundred_forty_kb,
 	},
 	{
 		.procname	= "perf_event_max_contexts_per_stack",
@@ -2644,7 +2586,7 @@
 		.mode		= 0644,
 		.proc_handler	= perf_event_max_stack_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_thousand,
+		.extra2		= SYSCTL_ONE_THOUSAND,
 	},
 #endif
 	{
@@ -2675,7 +2617,7 @@
 		.mode		= 0644,
 		.proc_handler	= bpf_unpriv_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 	{
 		.procname	= "bpf_stats_enabled",
@@ -2729,7 +2671,7 @@
 		.mode		= 0644,
 		.proc_handler	= overcommit_policy_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 	{
 		.procname	= "panic_on_oom",
@@ -2738,7 +2680,7 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 	{
 		.procname	= "oom_kill_allocating_task",
@@ -2783,7 +2725,7 @@
 		.mode		= 0644,
 		.proc_handler	= dirty_background_ratio_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= SYSCTL_ONE_HUNDRED,
 	},
 	{
 		.procname	= "dirty_background_bytes",
@@ -2791,7 +2733,7 @@
 		.maxlen		= sizeof(dirty_background_bytes),
 		.mode		= 0644,
 		.proc_handler	= dirty_background_bytes_handler,
-		.extra1		= &one_ul,
+		.extra1		= SYSCTL_LONG_ONE,
 	},
 	{
 		.procname	= "dirty_ratio",
@@ -2800,7 +2742,7 @@
 		.mode		= 0644,
 		.proc_handler	= dirty_ratio_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= SYSCTL_ONE_HUNDRED,
 	},
 	{
 		.procname	= "dirty_bytes",
@@ -2808,7 +2750,7 @@
 		.maxlen		= sizeof(vm_dirty_bytes),
 		.mode		= 0644,
 		.proc_handler	= dirty_bytes_handler,
-		.extra1		= &dirty_bytes_min,
+		.extra1		= (void *)&dirty_bytes_min,
 	},
 	{
 		.procname	= "dirty_writeback_centisecs",
@@ -2840,8 +2782,19 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two_hundred,
+		.extra2		= SYSCTL_TWO_HUNDRED,
 	},
+#ifdef CONFIG_NUMA
+	{
+		.procname	= "numa_stat",
+		.data		= &sysctl_vm_numa_stat,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= sysctl_vm_numa_stat_handler,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE,
+	},
+#endif
 #ifdef CONFIG_HUGETLB_PAGE
 	{
 		.procname	= "nr_hugepages",
@@ -2858,15 +2811,6 @@
 		.mode           = 0644,
 		.proc_handler   = &hugetlb_mempolicy_sysctl_handler,
 	},
-	{
-		.procname		= "numa_stat",
-		.data			= &sysctl_vm_numa_stat,
-		.maxlen			= sizeof(int),
-		.mode			= 0644,
-		.proc_handler	= sysctl_vm_numa_stat_handler,
-		.extra1			= SYSCTL_ZERO,
-		.extra2			= SYSCTL_ONE,
-	},
 #endif
 	 {
 		.procname	= "hugetlb_shm_group",
@@ -2897,7 +2841,7 @@
 		.mode		= 0200,
 		.proc_handler	= drop_caches_sysctl_handler,
 		.extra1		= SYSCTL_ONE,
-		.extra2		= &four,
+		.extra2		= SYSCTL_FOUR,
 	},
 #ifdef CONFIG_COMPACTION
 	{
@@ -2914,7 +2858,7 @@
 		.mode		= 0644,
 		.proc_handler	= compaction_proactiveness_sysctl_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= SYSCTL_ONE_HUNDRED,
 	},
 	{
 		.procname	= "extfrag_threshold",
@@ -2922,8 +2866,8 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &min_extfrag_threshold,
-		.extra2		= &max_extfrag_threshold,
+		.extra1		= (void *)&min_extfrag_threshold,
+		.extra2		= (void *)&max_extfrag_threshold,
 	},
 	{
 		.procname	= "compact_unevictable_allowed",
@@ -2959,7 +2903,7 @@
 		.mode		= 0644,
 		.proc_handler	= watermark_scale_factor_sysctl_handler,
 		.extra1		= SYSCTL_ONE,
-		.extra2		= &one_thousand,
+		.extra2		= SYSCTL_THREE_THOUSAND,
 	},
 	{
 		.procname	= "percpu_pagelist_high_fraction",
@@ -3038,7 +2982,7 @@
 		.mode		= 0644,
 		.proc_handler	= sysctl_min_unmapped_ratio_sysctl_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= SYSCTL_ONE_HUNDRED,
 	},
 	{
 		.procname	= "min_slab_ratio",
@@ -3047,7 +2991,7 @@
 		.mode		= 0644,
 		.proc_handler	= sysctl_min_slab_ratio_sysctl_handler,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= SYSCTL_ONE_HUNDRED,
 	},
 #endif
 #ifdef CONFIG_SMP
@@ -3183,45 +3127,6 @@
 
 static struct ctl_table fs_table[] = {
 	{
-		.procname	= "inode-nr",
-		.data		= &inodes_stat,
-		.maxlen		= 2*sizeof(long),
-		.mode		= 0444,
-		.proc_handler	= proc_nr_inodes,
-	},
-	{
-		.procname	= "inode-state",
-		.data		= &inodes_stat,
-		.maxlen		= 7*sizeof(long),
-		.mode		= 0444,
-		.proc_handler	= proc_nr_inodes,
-	},
-	{
-		.procname	= "file-nr",
-		.data		= &files_stat,
-		.maxlen		= sizeof(files_stat),
-		.mode		= 0444,
-		.proc_handler	= proc_nr_files,
-	},
-	{
-		.procname	= "file-max",
-		.data		= &files_stat.max_files,
-		.maxlen		= sizeof(files_stat.max_files),
-		.mode		= 0644,
-		.proc_handler	= proc_doulongvec_minmax,
-		.extra1		= &zero_ul,
-		.extra2		= &long_max,
-	},
-	{
-		.procname	= "nr_open",
-		.data		= &sysctl_nr_open,
-		.maxlen		= sizeof(unsigned int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &sysctl_nr_open_min,
-		.extra2		= &sysctl_nr_open_max,
-	},
-	{
 		.procname	= "dentry-state",
 		.data		= &dentry_stat,
 		.maxlen		= 6*sizeof(long),
@@ -3234,8 +3139,8 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &minolduid,
-		.extra2		= &maxolduid,
+		.extra1		= (void *)&minolduid,
+		.extra2		= (void *)&maxolduid,
 	},
 	{
 		.procname	= "overflowgid",
@@ -3243,8 +3148,8 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &minolduid,
-		.extra2		= &maxolduid,
+		.extra1		= (void *)&minolduid,
+		.extra2		= (void *)&maxolduid,
 	},
 #ifdef CONFIG_FILE_LOCKING
 	{
@@ -3337,7 +3242,7 @@
 		.mode		= 0600,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 	{
 		.procname	= "protected_regular",
@@ -3346,7 +3251,7 @@
 		.mode		= 0600,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 	{
 		.procname	= "suid_dumpable",
@@ -3355,7 +3260,7 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax_coredump,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &two,
+		.extra2		= SYSCTL_TWO,
 	},
 #if defined(CONFIG_BINFMT_MISC) || defined(CONFIG_BINFMT_MISC_MODULE)
 	{
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/task_work.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/task_work.c
@@ -60,6 +60,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL(task_work_add);
 
 /**
  * task_work_cancel_match - cancel a pending work added by task_work_add()
@@ -104,9 +105,9 @@
 }
 
 /**
- * task_work_cancel - cancel a pending work added by task_work_add()
- * @task: the task which should execute the work
- * @func: identifies the work to remove
+ * task_work_cancel_func - cancel a pending work matching a function added by task_work_add()
+ * @task: the task which should execute the func's work
+ * @func: identifies the func to match with a work to remove
  *
  * Find the last queued pending work with ->func == @func and remove
  * it from queue.
@@ -115,11 +116,35 @@
  * The found work or NULL if not found.
  */
 struct callback_head *
-task_work_cancel(struct task_struct *task, task_work_func_t func)
+task_work_cancel_func(struct task_struct *task, task_work_func_t func)
 {
 	return task_work_cancel_match(task, task_work_func_match, func);
 }
 
+static bool task_work_match(struct callback_head *cb, void *data)
+{
+	return cb == data;
+}
+
+/**
+ * task_work_cancel - cancel a pending work added by task_work_add()
+ * @task: the task which should execute the work
+ * @cb: the callback to remove if queued
+ *
+ * Remove a callback from a task's queue if queued.
+ *
+ * RETURNS:
+ * True if the callback was queued and got cancelled, false otherwise.
+ */
+bool task_work_cancel(struct task_struct *task, struct callback_head *cb)
+{
+	struct callback_head *ret;
+
+	ret = task_work_cancel_match(task, task_work_match, cb);
+
+	return ret == cb;
+}
+
 /**
  * task_work_run - execute the works added by task_work_add()
  *
@@ -152,7 +177,7 @@
 		if (!work)
 			break;
 		/*
-		 * Synchronize with task_work_cancel(). It can not remove
+		 * Synchronize with task_work_cancel_match(). It can not remove
 		 * the first entry == work, cmpxchg(task_works) must fail.
 		 * But it can remove another entry from the ->next list.
 		 */
@@ -167,3 +192,4 @@
 		} while (work);
 	}
 }
+EXPORT_SYMBOL_GPL(task_work_run);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/alarmtimer.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/alarmtimer.c
@@ -470,11 +470,35 @@
 }
 EXPORT_SYMBOL_GPL(alarm_forward);
 
-u64 alarm_forward_now(struct alarm *alarm, ktime_t interval)
+static u64 __alarm_forward_now(struct alarm *alarm, ktime_t interval, bool throttle)
 {
 	struct alarm_base *base = &alarm_bases[alarm->type];
+	ktime_t now = base->get_ktime();
+
+	if (IS_ENABLED(CONFIG_HIGH_RES_TIMERS) && throttle) {
+		/*
+		 * Same issue as with posix_timer_fn(). Timers which are
+		 * periodic but the signal is ignored can starve the system
+		 * with a very small interval. The real fix which was
+		 * promised in the context of posix_timer_fn() never
+		 * materialized, but someone should really work on it.
+		 *
+		 * To prevent DOS fake @now to be 1 jiffie out which keeps
+		 * the overrun accounting correct but creates an
+		 * inconsistency vs. timer_gettime(2).
+		 */
+		ktime_t kj = NSEC_PER_SEC / HZ;
+
+		if (interval < kj)
+			now = ktime_add(now, kj);
+	}
+
+	return alarm_forward(alarm, now, interval);
+}
 
-	return alarm_forward(alarm, base->get_ktime(), interval);
+u64 alarm_forward_now(struct alarm *alarm, ktime_t interval)
+{
+	return __alarm_forward_now(alarm, interval, false);
 }
 EXPORT_SYMBOL_GPL(alarm_forward_now);
 
@@ -551,9 +575,10 @@
 	if (posix_timer_event(ptr, si_private) && ptr->it_interval) {
 		/*
 		 * Handle ignored signals and rearm the timer. This will go
-		 * away once we handle ignored signals proper.
+		 * away once we handle ignored signals proper. Ensure that
+		 * small intervals cannot starve the system.
 		 */
-		ptr->it_overrun += alarm_forward_now(alarm, ptr->it_interval);
+		ptr->it_overrun += __alarm_forward_now(alarm, ptr->it_interval, true);
 		++ptr->it_requeue_pending;
 		ptr->it_active = 1;
 		result = ALARMTIMER_RESTART;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/clocksource-wdtest.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/clocksource-wdtest.c
@@ -104,8 +104,8 @@
 static int wdtest_func(void *arg)
 {
 	unsigned long j1, j2;
+	int i, max_retries;
 	char *s;
-	int i;
 
 	schedule_timeout_uninterruptible(holdoff * HZ);
 
@@ -139,18 +139,19 @@
 	WARN_ON_ONCE(time_before(j2, j1 + NSEC_PER_USEC));
 
 	/* Verify tsc-like stability with various numbers of errors injected. */
-	for (i = 0; i <= max_cswd_read_retries + 1; i++) {
-		if (i <= 1 && i < max_cswd_read_retries)
+	max_retries = clocksource_get_max_watchdog_retry();
+	for (i = 0; i <= max_retries + 1; i++) {
+		if (i <= 1 && i < max_retries)
 			s = "";
-		else if (i <= max_cswd_read_retries)
+		else if (i <= max_retries)
 			s = ", expect message";
 		else
 			s = ", expect clock skew";
-		pr_info("--- Watchdog with %dx error injection, %lu retries%s.\n", i, max_cswd_read_retries, s);
+		pr_info("--- Watchdog with %dx error injection, %d retries%s.\n", i, max_retries, s);
 		WRITE_ONCE(wdtest_ktime_read_ndelays, i);
 		schedule_timeout_uninterruptible(2 * HZ);
 		WARN_ON_ONCE(READ_ONCE(wdtest_ktime_read_ndelays));
-		WARN_ON_ONCE((i <= max_cswd_read_retries) !=
+		WARN_ON_ONCE((i <= max_retries) !=
 			     !(clocksource_wdtest_ktime.flags & CLOCK_SOURCE_UNSTABLE));
 		wdtest_ktime_clocksource_reset();
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/clocksource.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/clocksource.c
@@ -20,6 +20,16 @@
 #include "tick-internal.h"
 #include "timekeeping_internal.h"
 
+static noinline u64 cycles_to_nsec_safe(struct clocksource *cs, u64 start, u64 end)
+{
+	u64 delta = clocksource_delta(end, start, cs->mask);
+
+	if (likely(delta < cs->max_cycles))
+		return clocksource_cyc2ns(delta, cs->mult, cs->shift);
+
+	return mul_u64_u32_shr(delta, cs->mult, cs->shift);
+}
+
 /**
  * clocks_calc_mult_shift - calculate mult/shift factors for scaled math of clocks
  * @mult:	pointer to mult variable
@@ -107,7 +117,7 @@
  * This delay could be due to SMIs, NMIs, or to VCPU preemptions.  Used as
  * a lower bound for cs->uncertainty_margin values when registering clocks.
  */
-#define WATCHDOG_MAX_SKEW (50 * NSEC_PER_USEC)
+#define WATCHDOG_MAX_SKEW (100 * NSEC_PER_USEC)
 
 #ifdef CONFIG_CLOCKSOURCE_WATCHDOG
 static void clocksource_watchdog_work(struct work_struct *work);
@@ -120,6 +130,7 @@
 static DEFINE_SPINLOCK(watchdog_lock);
 static int watchdog_running;
 static atomic_t watchdog_reset_pending;
+static int64_t watchdog_max_interval;
 
 static inline void clocksource_watchdog_lock(unsigned long *flags)
 {
@@ -138,6 +149,7 @@
  * Interval: 0.5sec.
  */
 #define WATCHDOG_INTERVAL (HZ >> 1)
+#define WATCHDOG_INTERVAL_MAX_NS ((2 * WATCHDOG_INTERVAL) * (NSEC_PER_SEC / HZ))
 
 static void clocksource_watchdog_work(struct work_struct *work)
 {
@@ -199,40 +211,63 @@
 	spin_unlock_irqrestore(&watchdog_lock, flags);
 }
 
-ulong max_cswd_read_retries = 3;
-module_param(max_cswd_read_retries, ulong, 0644);
-EXPORT_SYMBOL_GPL(max_cswd_read_retries);
 static int verify_n_cpus = 8;
 module_param(verify_n_cpus, int, 0644);
 
-static bool cs_watchdog_read(struct clocksource *cs, u64 *csnow, u64 *wdnow)
-{
-	unsigned int nretries;
-	u64 wd_end, wd_delta;
-	int64_t wd_delay;
+enum wd_read_status {
+	WD_READ_SUCCESS,
+	WD_READ_UNSTABLE,
+	WD_READ_SKIP
+};
+
+static enum wd_read_status cs_watchdog_read(struct clocksource *cs, u64 *csnow, u64 *wdnow)
+{
+	unsigned int nretries, max_retries;
+	int64_t wd_delay, wd_seq_delay;
+	u64 wd_end, wd_end2;
 
-	for (nretries = 0; nretries <= max_cswd_read_retries; nretries++) {
+	max_retries = clocksource_get_max_watchdog_retry();
+	for (nretries = 0; nretries <= max_retries; nretries++) {
 		local_irq_disable();
 		*wdnow = watchdog->read(watchdog);
 		*csnow = cs->read(cs);
 		wd_end = watchdog->read(watchdog);
+		wd_end2 = watchdog->read(watchdog);
 		local_irq_enable();
 
-		wd_delta = clocksource_delta(wd_end, *wdnow, watchdog->mask);
-		wd_delay = clocksource_cyc2ns(wd_delta, watchdog->mult,
-					      watchdog->shift);
+		wd_delay = cycles_to_nsec_safe(watchdog, *wdnow, wd_end);
 		if (wd_delay <= WATCHDOG_MAX_SKEW) {
-			if (nretries > 1 || nretries >= max_cswd_read_retries) {
+			if (nretries > 1 && nretries >= max_retries) {
 				pr_warn("timekeeping watchdog on CPU%d: %s retried %d times before success\n",
 					smp_processor_id(), watchdog->name, nretries);
 			}
-			return true;
+			return WD_READ_SUCCESS;
 		}
+
+		/*
+		 * Now compute delay in consecutive watchdog read to see if
+		 * there is too much external interferences that cause
+		 * significant delay in reading both clocksource and watchdog.
+		 *
+		 * If consecutive WD read-back delay > WATCHDOG_MAX_SKEW/2,
+		 * report system busy, reinit the watchdog and skip the current
+		 * watchdog test.
+		 */
+		wd_seq_delay = cycles_to_nsec_safe(watchdog, wd_end, wd_end2);
+		if (wd_seq_delay > WATCHDOG_MAX_SKEW/2)
+			goto skip_test;
 	}
 
 	pr_warn("timekeeping watchdog on CPU%d: %s read-back delay of %lldns, attempt %d, marking unstable\n",
 		smp_processor_id(), watchdog->name, wd_delay, nretries);
-	return false;
+	return WD_READ_UNSTABLE;
+
+skip_test:
+	pr_info("timekeeping watchdog on CPU%d: %s wd-wd read-back delay of %lldns\n",
+		smp_processor_id(), watchdog->name, wd_seq_delay);
+	pr_info("wd-%s-wd read-back delay of %lldns, clock-skew test skipped!\n",
+		cs->name, wd_delay);
+	return WD_READ_SKIP;
 }
 
 static u64 csnow_mid;
@@ -307,16 +342,18 @@
 	cpumask_clear(&cpus_ahead);
 	cpumask_clear(&cpus_behind);
 	cpus_read_lock();
-	preempt_disable();
+	migrate_disable();
 	clocksource_verify_choose_cpus();
-	if (cpumask_weight(&cpus_chosen) == 0) {
-		preempt_enable();
+	if (cpumask_empty(&cpus_chosen)) {
+		migrate_enable();
 		cpus_read_unlock();
 		pr_warn("Not enough CPUs to check clocksource '%s'.\n", cs->name);
 		return;
 	}
 	testcpu = smp_processor_id();
-	pr_warn("Checking clocksource %s synchronization from CPU %d to CPUs %*pbl.\n", cs->name, testcpu, cpumask_pr_args(&cpus_chosen));
+	pr_info("Checking clocksource %s synchronization from CPU %d to CPUs %*pbl.\n",
+		cs->name, testcpu, cpumask_pr_args(&cpus_chosen));
+	preempt_disable();
 	for_each_cpu(cpu, &cpus_chosen) {
 		if (cpu == testcpu)
 			continue;
@@ -329,14 +366,14 @@
 		delta = (csnow_end - csnow_mid) & cs->mask;
 		if (delta < 0)
 			cpumask_set_cpu(cpu, &cpus_ahead);
-		delta = clocksource_delta(csnow_end, csnow_begin, cs->mask);
-		cs_nsec = clocksource_cyc2ns(delta, cs->mult, cs->shift);
+		cs_nsec = cycles_to_nsec_safe(cs, csnow_begin, csnow_end);
 		if (cs_nsec > cs_nsec_max)
 			cs_nsec_max = cs_nsec;
 		if (cs_nsec < cs_nsec_min)
 			cs_nsec_min = cs_nsec;
 	}
 	preempt_enable();
+	migrate_enable();
 	cpus_read_unlock();
 	if (!cpumask_empty(&cpus_ahead))
 		pr_warn("        CPUs %*pbl ahead of CPU %d for clocksource %s.\n",
@@ -350,12 +387,23 @@
 }
 EXPORT_SYMBOL_GPL(clocksource_verify_percpu);
 
+static inline void clocksource_reset_watchdog(void)
+{
+	struct clocksource *cs;
+
+	list_for_each_entry(cs, &watchdog_list, wd_list)
+		cs->flags &= ~CLOCK_SOURCE_WATCHDOG;
+}
+
+
 static void clocksource_watchdog(struct timer_list *unused)
 {
-	u64 csnow, wdnow, cslast, wdlast, delta;
+	int64_t wd_nsec, cs_nsec, interval;
+	u64 csnow, wdnow, cslast, wdlast;
 	int next_cpu, reset_pending;
-	int64_t wd_nsec, cs_nsec;
 	struct clocksource *cs;
+	enum wd_read_status read_ret;
+	unsigned long extra_wait = 0;
 	u32 md;
 
 	spin_lock(&watchdog_lock);
@@ -373,12 +421,32 @@
 			continue;
 		}
 
-		if (!cs_watchdog_read(cs, &csnow, &wdnow)) {
+		read_ret = cs_watchdog_read(cs, &csnow, &wdnow);
+
+		if (read_ret == WD_READ_UNSTABLE) {
 			/* Clock readout unreliable, so give it up. */
 			__clocksource_unstable(cs);
 			continue;
 		}
 
+		/*
+		 * When WD_READ_SKIP is returned, it means the system is likely
+		 * under very heavy load, where the latency of reading
+		 * watchdog/clocksource is very big, and affect the accuracy of
+		 * watchdog check. So give system some space and suspend the
+		 * watchdog check for 5 minutes.
+		 */
+		if (read_ret == WD_READ_SKIP) {
+			/*
+			 * As the watchdog timer will be suspended, and
+			 * cs->last could keep unchanged for 5 minutes, reset
+			 * the counters.
+			 */
+			clocksource_reset_watchdog();
+			extra_wait = HZ * 300;
+			break;
+		}
+
 		/* Clocksource initialized ? */
 		if (!(cs->flags & CLOCK_SOURCE_WATCHDOG) ||
 		    atomic_read(&watchdog_reset_pending)) {
@@ -388,12 +456,8 @@
 			continue;
 		}
 
-		delta = clocksource_delta(wdnow, cs->wd_last, watchdog->mask);
-		wd_nsec = clocksource_cyc2ns(delta, watchdog->mult,
-					     watchdog->shift);
-
-		delta = clocksource_delta(csnow, cs->cs_last, cs->mask);
-		cs_nsec = clocksource_cyc2ns(delta, cs->mult, cs->shift);
+		wd_nsec = cycles_to_nsec_safe(watchdog, cs->wd_last, wdnow);
+		cs_nsec = cycles_to_nsec_safe(cs, cs->cs_last, csnow);
 		wdlast = cs->wd_last; /* save these in case we print them */
 		cslast = cs->cs_last;
 		cs->cs_last = csnow;
@@ -402,6 +466,27 @@
 		if (atomic_read(&watchdog_reset_pending))
 			continue;
 
+		/*
+		 * The processing of timer softirqs can get delayed (usually
+		 * on account of ksoftirqd not getting to run in a timely
+		 * manner), which causes the watchdog interval to stretch.
+		 * Skew detection may fail for longer watchdog intervals
+		 * on account of fixed margins being used.
+		 * Some clocksources, e.g. acpi_pm, cannot tolerate
+		 * watchdog intervals longer than a few seconds.
+		 */
+		interval = max(cs_nsec, wd_nsec);
+		if (unlikely(interval > WATCHDOG_INTERVAL_MAX_NS)) {
+			if (system_state > SYSTEM_SCHEDULING &&
+			    interval > 2 * watchdog_max_interval) {
+				watchdog_max_interval = interval;
+				pr_warn("Long readout interval, skipping watchdog check: cs_nsec: %lld wd_nsec: %lld\n",
+					cs_nsec, wd_nsec);
+			}
+			watchdog_timer.expires = jiffies;
+			continue;
+		}
+
 		/* Check the deviation from the watchdog clocksource. */
 		md = cs->uncertainty_margin + watchdog->uncertainty_margin;
 		if (abs(cs_nsec - wd_nsec) > md) {
@@ -474,7 +559,7 @@
 	 * pair clocksource_stop_watchdog() clocksource_start_watchdog().
 	 */
 	if (!timer_pending(&watchdog_timer)) {
-		watchdog_timer.expires += WATCHDOG_INTERVAL;
+		watchdog_timer.expires += WATCHDOG_INTERVAL + extra_wait;
 		add_timer_on(&watchdog_timer, next_cpu);
 	}
 out:
@@ -499,14 +584,6 @@
 	watchdog_running = 0;
 }
 
-static inline void clocksource_reset_watchdog(void)
-{
-	struct clocksource *cs;
-
-	list_for_each_entry(cs, &watchdog_list, wd_list)
-		cs->flags &= ~CLOCK_SOURCE_WATCHDOG;
-}
-
 static void clocksource_resume_watchdog(void)
 {
 	atomic_inc(&watchdog_reset_pending);
@@ -743,7 +820,7 @@
  */
 u64 clocksource_stop_suspend_timing(struct clocksource *cs, u64 cycle_now)
 {
-	u64 now, delta, nsec = 0;
+	u64 now, nsec = 0;
 
 	if (!suspend_clocksource)
 		return 0;
@@ -758,12 +835,8 @@
 	else
 		now = suspend_clocksource->read(suspend_clocksource);
 
-	if (now > suspend_start) {
-		delta = clocksource_delta(now, suspend_start,
-					  suspend_clocksource->mask);
-		nsec = mul_u64_u32_shr(delta, suspend_clocksource->mult,
-				       suspend_clocksource->shift);
-	}
+	if (now > suspend_start)
+		nsec = cycles_to_nsec_safe(suspend_clocksource, suspend_start, now);
 
 	/*
 	 * Disable the suspend timer to save power if current clocksource is
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/hrtimer.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/hrtimer.c
@@ -144,11 +144,6 @@
 
 #define migration_base	migration_cpu_base.clock_base[0]
 
-static inline bool is_migration_base(struct hrtimer_clock_base *base)
-{
-	return base == &migration_base;
-}
-
 /*
  * We are using hashed locking: holding per_cpu(hrtimer_bases)[n].lock
  * means that all timers which are tied to this base via timer->base are
@@ -273,11 +268,6 @@
 
 #else /* CONFIG_SMP */
 
-static inline bool is_migration_base(struct hrtimer_clock_base *base)
-{
-	return false;
-}
-
 static inline struct hrtimer_clock_base *
 lock_hrtimer_base(const struct hrtimer *timer, unsigned long *flags)
 {
@@ -1082,6 +1072,7 @@
 			   enum hrtimer_mode mode)
 {
 	debug_activate(timer, mode);
+	WARN_ON_ONCE(!base->cpu_base->online);
 
 	base->cpu_base->active_bases |= 1 << base->index;
 
@@ -1283,6 +1274,8 @@
 	struct hrtimer_clock_base *base;
 	unsigned long flags;
 
+	if (WARN_ON_ONCE(!timer->function))
+		return;
 	/*
 	 * Check whether the HRTIMER_MODE_SOFT bit and hrtimer.is_soft
 	 * match on CONFIG_PREEMPT_RT = n. With PREEMPT_RT check the hard
@@ -1374,6 +1367,18 @@
 	}
 }
 
+#ifdef CONFIG_SMP
+static __always_inline bool is_migration_base(struct hrtimer_clock_base *base)
+{
+	return base == &migration_base;
+}
+#else
+static __always_inline bool is_migration_base(struct hrtimer_clock_base *base)
+{
+	return false;
+}
+#endif
+
 /*
  * This function is called on PREEMPT_RT kernels when the fast path
  * deletion of a timer failed because the timer callback function was
@@ -2126,6 +2131,7 @@
 	if (!timespec64_valid(&tu))
 		return -EINVAL;
 
+	current->restart_block.fn = do_no_restart_syscall;
 	current->restart_block.nanosleep.type = rmtp ? TT_NATIVE : TT_NONE;
 	current->restart_block.nanosleep.rmtp = rmtp;
 	return hrtimer_nanosleep(timespec64_to_ktime(tu), HRTIMER_MODE_REL,
@@ -2147,6 +2153,7 @@
 	if (!timespec64_valid(&tu))
 		return -EINVAL;
 
+	current->restart_block.fn = do_no_restart_syscall;
 	current->restart_block.nanosleep.type = rmtp ? TT_COMPAT : TT_NONE;
 	current->restart_block.nanosleep.compat_rmtp = rmtp;
 	return hrtimer_nanosleep(timespec64_to_ktime(tu), HRTIMER_MODE_REL,
@@ -2171,6 +2178,15 @@
 	}
 
 	cpu_base->cpu = cpu;
+	hrtimer_cpu_base_init_expiry_lock(cpu_base);
+	return 0;
+}
+
+int hrtimers_cpu_starting(unsigned int cpu)
+{
+	struct hrtimer_cpu_base *cpu_base = this_cpu_ptr(&hrtimer_bases);
+
+	/* Clear out any left over state from a CPU down operation */
 	cpu_base->active_bases = 0;
 	cpu_base->hres_active = 0;
 	cpu_base->hang_detected = 0;
@@ -2178,7 +2194,7 @@
 	cpu_base->softirq_next_timer = NULL;
 	cpu_base->expires_next = KTIME_MAX;
 	cpu_base->softirq_expires_next = KTIME_MAX;
-	hrtimer_cpu_base_init_expiry_lock(cpu_base);
+	cpu_base->online = 1;
 	return 0;
 }
 
@@ -2214,29 +2230,22 @@
 	}
 }
 
-int hrtimers_dead_cpu(unsigned int scpu)
+int hrtimers_cpu_dying(unsigned int dying_cpu)
 {
 	struct hrtimer_cpu_base *old_base, *new_base;
-	int i;
+	int i, ncpu = cpumask_first(cpu_active_mask);
 
-	BUG_ON(cpu_online(scpu));
-	tick_cancel_sched_timer(scpu);
+	tick_cancel_sched_timer(dying_cpu);
+
+	old_base = this_cpu_ptr(&hrtimer_bases);
+	new_base = &per_cpu(hrtimer_bases, ncpu);
 
-	/*
-	 * this BH disable ensures that raise_softirq_irqoff() does
-	 * not wakeup ksoftirqd (and acquire the pi-lock) while
-	 * holding the cpu_base lock
-	 */
-	local_bh_disable();
-	local_irq_disable();
-	old_base = &per_cpu(hrtimer_bases, scpu);
-	new_base = this_cpu_ptr(&hrtimer_bases);
 	/*
 	 * The caller is globally serialized and nobody else
 	 * takes two locks at once, deadlock is not possible.
 	 */
-	raw_spin_lock(&new_base->lock);
-	raw_spin_lock_nested(&old_base->lock, SINGLE_DEPTH_NESTING);
+	raw_spin_lock(&old_base->lock);
+	raw_spin_lock_nested(&new_base->lock, SINGLE_DEPTH_NESTING);
 
 	for (i = 0; i < HRTIMER_MAX_CLOCK_BASES; i++) {
 		migrate_hrtimer_list(&old_base->clock_base[i],
@@ -2247,15 +2256,14 @@
 	 * The migration might have changed the first expiring softirq
 	 * timer on this CPU. Update it.
 	 */
-	hrtimer_update_softirq_timer(new_base, false);
+	__hrtimer_get_next_event(new_base, HRTIMER_ACTIVE_SOFT);
+	/* Tell the other CPU to retrigger the next event */
+	smp_call_function_single(ncpu, retrigger_next_event, NULL, 0);
 
-	raw_spin_unlock(&old_base->lock);
 	raw_spin_unlock(&new_base->lock);
+	old_base->online = 0;
+	raw_spin_unlock(&old_base->lock);
 
-	/* Check, if we got expired work to do */
-	__hrtimer_peek_ahead_timers();
-	local_irq_enable();
-	local_bh_enable();
 	return 0;
 }
 
@@ -2264,13 +2272,14 @@
 void __init hrtimers_init(void)
 {
 	hrtimers_prepare_cpu(smp_processor_id());
+	hrtimers_cpu_starting(smp_processor_id());
 	open_softirq(HRTIMER_SOFTIRQ, hrtimer_run_softirq);
 }
 
 /**
  * schedule_hrtimeout_range_clock - sleep until timeout
  * @expires:	timeout value (ktime_t)
- * @delta:	slack in expires timeout (ktime_t)
+ * @delta:	slack in expires timeout (ktime_t) for SCHED_OTHER tasks
  * @mode:	timer mode
  * @clock_id:	timer clock to be used
  */
@@ -2297,6 +2306,13 @@
 		return -EINTR;
 	}
 
+	/*
+	 * Override any slack passed by the user if under
+	 * rt contraints.
+	 */
+	if (rt_task(current))
+		delta = 0;
+
 	hrtimer_init_sleeper_on_stack(&t, clock_id, mode);
 	hrtimer_set_expires_range_ns(&t.timer, *expires, delta);
 	hrtimer_sleeper_start_expires(&t, mode);
@@ -2311,11 +2327,12 @@
 
 	return !t.task ? 0 : -EINTR;
 }
+EXPORT_SYMBOL_GPL(schedule_hrtimeout_range_clock);
 
 /**
  * schedule_hrtimeout_range - sleep until timeout
  * @expires:	timeout value (ktime_t)
- * @delta:	slack in expires timeout (ktime_t)
+ * @delta:	slack in expires timeout (ktime_t) for SCHED_OTHER tasks
  * @mode:	timer mode
  *
  * Make the current task sleep until the given expiry time has
@@ -2323,7 +2340,8 @@
  * the current task state has been set (see set_current_state()).
  *
  * The @delta argument gives the kernel the freedom to schedule the
- * actual wakeup to a time that is both power and performance friendly.
+ * actual wakeup to a time that is both power and performance friendly
+ * for regular (non RT/DL) tasks.
  * The kernel give the normal best effort behavior for "@expires+@delta",
  * but may decide to fire the timer earlier, but no earlier than @expires.
  *
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/ntp.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/ntp.c
@@ -727,17 +727,16 @@
 	}
 
 	if (txc->modes & ADJ_MAXERROR)
-		time_maxerror = txc->maxerror;
+		time_maxerror = clamp(txc->maxerror, 0, NTP_PHASE_LIMIT);
 
 	if (txc->modes & ADJ_ESTERROR)
-		time_esterror = txc->esterror;
+		time_esterror = clamp(txc->esterror, 0, NTP_PHASE_LIMIT);
 
 	if (txc->modes & ADJ_TIMECONST) {
-		time_constant = txc->constant;
+		time_constant = clamp(txc->constant, 0, MAXTC);
 		if (!(time_status & STA_NANO))
 			time_constant += 4;
-		time_constant = min(time_constant, (long)MAXTC);
-		time_constant = max(time_constant, 0l);
+		time_constant = clamp(time_constant, 0, MAXTC);
 	}
 
 	if (txc->modes & ADJ_TAI &&
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/posix-clock.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/posix-clock.c
@@ -290,6 +290,9 @@
 	struct posix_clock_desc cd;
 	int err;
 
+	if (!timespec64_valid_strict(ts))
+		return -EINVAL;
+
 	err = get_clock_desc(id, &cd);
 	if (err)
 		return err;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/posix-cpu-timers.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/posix-cpu-timers.c
@@ -840,6 +840,8 @@
 			return expires;
 
 		ctmr->firing = 1;
+		/* See posix_cpu_timer_wait_running() */
+		rcu_assign_pointer(ctmr->handling, current);
 		cpu_timer_dequeue(ctmr);
 		list_add_tail(&ctmr->elist, firing);
 	}
@@ -1155,7 +1157,66 @@
 #ifdef CONFIG_POSIX_CPU_TIMERS_TASK_WORK
 static void posix_cpu_timers_work(struct callback_head *work)
 {
+	struct posix_cputimers_work *cw = container_of(work, typeof(*cw), work);
+
+	mutex_lock(&cw->mutex);
 	handle_posix_cpu_timers(current);
+	mutex_unlock(&cw->mutex);
+}
+
+/*
+ * Invoked from the posix-timer core when a cancel operation failed because
+ * the timer is marked firing. The caller holds rcu_read_lock(), which
+ * protects the timer and the task which is expiring it from being freed.
+ */
+static void posix_cpu_timer_wait_running(struct k_itimer *timr)
+{
+	struct task_struct *tsk = rcu_dereference(timr->it.cpu.handling);
+
+	/* Has the handling task completed expiry already? */
+	if (!tsk)
+		return;
+
+	/* Ensure that the task cannot go away */
+	get_task_struct(tsk);
+	/* Now drop the RCU protection so the mutex can be locked */
+	rcu_read_unlock();
+	/* Wait on the expiry mutex */
+	mutex_lock(&tsk->posix_cputimers_work.mutex);
+	/* Release it immediately again. */
+	mutex_unlock(&tsk->posix_cputimers_work.mutex);
+	/* Drop the task reference. */
+	put_task_struct(tsk);
+	/* Relock RCU so the callsite is balanced */
+	rcu_read_lock();
+}
+
+static void posix_cpu_timer_wait_running_nsleep(struct k_itimer *timr)
+{
+	/* Ensure that timr->it.cpu.handling task cannot go away */
+	rcu_read_lock();
+	spin_unlock_irq(&timr->it_lock);
+	posix_cpu_timer_wait_running(timr);
+	rcu_read_unlock();
+	/* @timr is on stack and is valid */
+	spin_lock_irq(&timr->it_lock);
+}
+
+/*
+ * Clear existing posix CPU timers task work.
+ */
+void clear_posix_cputimers_work(struct task_struct *p)
+{
+	/*
+	 * A copied work entry from the old task is not meaningful, clear it.
+	 * N.B. init_task_work will not do this.
+	 */
+	memset(&p->posix_cputimers_work.work, 0,
+	       sizeof(p->posix_cputimers_work.work));
+	init_task_work(&p->posix_cputimers_work.work,
+		       posix_cpu_timers_work);
+	mutex_init(&p->posix_cputimers_work.mutex);
+	p->posix_cputimers_work.scheduled = false;
 }
 
 /*
@@ -1164,8 +1225,7 @@
  */
 void __init posix_cputimers_init_work(void)
 {
-	init_task_work(&current->posix_cputimers_work.work,
-		       posix_cpu_timers_work);
+	clear_posix_cputimers_work(current);
 }
 
 /*
@@ -1234,6 +1294,18 @@
 	lockdep_posixtimer_exit();
 }
 
+static void posix_cpu_timer_wait_running(struct k_itimer *timr)
+{
+	cpu_relax();
+}
+
+static void posix_cpu_timer_wait_running_nsleep(struct k_itimer *timr)
+{
+	spin_unlock_irq(&timr->it_lock);
+	cpu_relax();
+	spin_lock_irq(&timr->it_lock);
+}
+
 static inline bool posix_cpu_timers_work_scheduled(struct task_struct *tsk)
 {
 	return false;
@@ -1342,6 +1414,8 @@
 		 */
 		if (likely(cpu_firing >= 0))
 			cpu_timer_fire(timer);
+		/* See posix_cpu_timer_wait_running() */
+		rcu_assign_pointer(timer->it.cpu.handling, NULL);
 		spin_unlock(&timer->it_lock);
 	}
 }
@@ -1476,23 +1550,16 @@
 		expires = cpu_timer_getexpires(&timer.it.cpu);
 		error = posix_cpu_timer_set(&timer, 0, &zero_it, &it);
 		if (!error) {
-			/*
-			 * Timer is now unarmed, deletion can not fail.
-			 */
+			/* Timer is now unarmed, deletion can not fail. */
 			posix_cpu_timer_del(&timer);
+		} else {
+			while (error == TIMER_RETRY) {
+				posix_cpu_timer_wait_running_nsleep(&timer);
+				error = posix_cpu_timer_del(&timer);
+			}
 		}
-		spin_unlock_irq(&timer.it_lock);
 
-		while (error == TIMER_RETRY) {
-			/*
-			 * We need to handle case when timer was or is in the
-			 * middle of firing. In other cases we already freed
-			 * resources.
-			 */
-			spin_lock_irq(&timer.it_lock);
-			error = posix_cpu_timer_del(&timer);
-			spin_unlock_irq(&timer.it_lock);
-		}
+		spin_unlock_irq(&timer.it_lock);
 
 		if ((it.it_value.tv_sec | it.it_value.tv_nsec) == 0) {
 			/*
@@ -1602,6 +1669,7 @@
 	.timer_del		= posix_cpu_timer_del,
 	.timer_get		= posix_cpu_timer_get,
 	.timer_rearm		= posix_cpu_timer_rearm,
+	.timer_wait_running	= posix_cpu_timer_wait_running,
 };
 
 const struct k_clock clock_process = {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/posix-stubs.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/posix-stubs.c
@@ -146,6 +146,7 @@
 		return -EINVAL;
 	if (flags & TIMER_ABSTIME)
 		rmtp = NULL;
+	current->restart_block.fn = do_no_restart_syscall;
 	current->restart_block.nanosleep.type = rmtp ? TT_NATIVE : TT_NONE;
 	current->restart_block.nanosleep.rmtp = rmtp;
 	texp = timespec64_to_ktime(t);
@@ -239,6 +240,7 @@
 		return -EINVAL;
 	if (flags & TIMER_ABSTIME)
 		rmtp = NULL;
+	current->restart_block.fn = do_no_restart_syscall;
 	current->restart_block.nanosleep.type = rmtp ? TT_COMPAT : TT_NONE;
 	current->restart_block.nanosleep.compat_rmtp = rmtp;
 	texp = timespec64_to_ktime(t);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/posix-timers.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/posix-timers.c
@@ -140,25 +140,30 @@
 static int posix_timer_add(struct k_itimer *timer)
 {
 	struct signal_struct *sig = current->signal;
-	int first_free_id = sig->posix_timer_id;
 	struct hlist_head *head;
-	int ret = -ENOENT;
+	unsigned int cnt, id;
 
-	do {
+	/*
+	 * FIXME: Replace this by a per signal struct xarray once there is
+	 * a plan to handle the resulting CRIU regression gracefully.
+	 */
+	for (cnt = 0; cnt <= INT_MAX; cnt++) {
 		spin_lock(&hash_lock);
-		head = &posix_timers_hashtable[hash(sig, sig->posix_timer_id)];
-		if (!__posix_timers_find(head, sig, sig->posix_timer_id)) {
+		id = sig->next_posix_timer_id;
+
+		/* Write the next ID back. Clamp it to the positive space */
+		sig->next_posix_timer_id = (id + 1) & INT_MAX;
+
+		head = &posix_timers_hashtable[hash(sig, id)];
+		if (!__posix_timers_find(head, sig, id)) {
 			hlist_add_head_rcu(&timer->t_hash, head);
-			ret = sig->posix_timer_id;
+			spin_unlock(&hash_lock);
+			return id;
 		}
-		if (++sig->posix_timer_id < 0)
-			sig->posix_timer_id = 0;
-		if ((sig->posix_timer_id == first_free_id) && (ret == -ENOENT))
-			/* Loop over all possible ids completed */
-			ret = -EAGAIN;
 		spin_unlock(&hash_lock);
-	} while (ret == -ENOENT);
-	return ret;
+	}
+	/* POSIX return code when no timer ID could be allocated */
+	return -EAGAIN;
 }
 
 static inline void unlock_timer(struct k_itimer *timr, unsigned long flags)
@@ -846,6 +851,10 @@
 	rcu_read_lock();
 	unlock_timer(timer, *flags);
 
+	/*
+	 * kc->timer_wait_running() might drop RCU lock. So @timer
+	 * cannot be touched anymore after the function returns!
+	 */
 	if (!WARN_ON_ONCE(!kc->timer_wait_running))
 		kc->timer_wait_running(timer);
 
@@ -1033,33 +1042,69 @@
 }
 
 /*
- * return timer owned by the process, used by exit_itimers
+ * Delete a timer if it is armed, remove it from the hash and schedule it
+ * for RCU freeing.
  */
 static void itimer_delete(struct k_itimer *timer)
 {
-retry_delete:
-	spin_lock_irq(&timer->it_lock);
+	unsigned long flags;
+
+	/*
+	 * irqsave is required to make timer_wait_running() work.
+	 */
+	spin_lock_irqsave(&timer->it_lock, flags);
 
+retry_delete:
+	/*
+	 * Even if the timer is not longer accessible from other tasks
+	 * it still might be armed and queued in the underlying timer
+	 * mechanism. Worse, that timer mechanism might run the expiry
+	 * function concurrently.
+	 */
 	if (timer_delete_hook(timer) == TIMER_RETRY) {
-		spin_unlock_irq(&timer->it_lock);
+		/*
+		 * Timer is expired concurrently, prevent livelocks
+		 * and pointless spinning on RT.
+		 *
+		 * timer_wait_running() drops timer::it_lock, which opens
+		 * the possibility for another task to delete the timer.
+		 *
+		 * That's not possible here because this is invoked from
+		 * do_exit() only for the last thread of the thread group.
+		 * So no other task can access and delete that timer.
+		 */
+		if (WARN_ON_ONCE(timer_wait_running(timer, &flags) != timer))
+			return;
+
 		goto retry_delete;
 	}
 	list_del(&timer->list);
 
-	spin_unlock_irq(&timer->it_lock);
+	spin_unlock_irqrestore(&timer->it_lock, flags);
 	release_posix_timer(timer, IT_ID_SET);
 }
 
 /*
- * This is called by do_exit or de_thread, only when there are no more
- * references to the shared signal_struct.
+ * Invoked from do_exit() when the last thread of a thread group exits.
+ * At that point no other task can access the timers of the dying
+ * task anymore.
  */
-void exit_itimers(struct signal_struct *sig)
+void exit_itimers(struct task_struct *tsk)
 {
+	struct list_head timers;
 	struct k_itimer *tmr;
 
-	while (!list_empty(&sig->posix_timers)) {
-		tmr = list_entry(sig->posix_timers.next, struct k_itimer, list);
+	if (list_empty(&tsk->signal->posix_timers))
+		return;
+
+	/* Protect against concurrent read via /proc/$PID/timers */
+	spin_lock_irq(&tsk->sighand->siglock);
+	list_replace_init(&tsk->signal->posix_timers, &timers);
+	spin_unlock_irq(&tsk->sighand->siglock);
+
+	/* The timers are not longer accessible via tsk::signal */
+	while (!list_empty(&timers)) {
+		tmr = list_first_entry(&timers, struct k_itimer, list);
 		itimer_delete(tmr);
 	}
 }
@@ -1261,6 +1306,7 @@
 		return -EINVAL;
 	if (flags & TIMER_ABSTIME)
 		rmtp = NULL;
+	current->restart_block.fn = do_no_restart_syscall;
 	current->restart_block.nanosleep.type = rmtp ? TT_NATIVE : TT_NONE;
 	current->restart_block.nanosleep.rmtp = rmtp;
 
@@ -1288,6 +1334,7 @@
 		return -EINVAL;
 	if (flags & TIMER_ABSTIME)
 		rmtp = NULL;
+	current->restart_block.fn = do_no_restart_syscall;
 	current->restart_block.nanosleep.type = rmtp ? TT_COMPAT : TT_NONE;
 	current->restart_block.nanosleep.compat_rmtp = rmtp;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/sched_clock.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/sched_clock.c
@@ -76,7 +76,7 @@
 
 notrace int sched_clock_read_retry(unsigned int seq)
 {
-	return read_seqcount_latch_retry(&cd.seq, seq);
+	return raw_read_seqcount_latch_retry(&cd.seq, seq);
 }
 
 unsigned long long notrace sched_clock(void)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/test_udelay.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/test_udelay.c
@@ -149,7 +149,7 @@
 static void __exit udelay_test_exit(void)
 {
 	mutex_lock(&udelay_test_lock);
-	debugfs_remove(debugfs_lookup(DEBUGFS_FILENAME, NULL));
+	debugfs_lookup_and_remove(DEBUGFS_FILENAME, NULL);
 	mutex_unlock(&udelay_test_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/tick-broadcast.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/tick-broadcast.c
@@ -35,14 +35,15 @@
 #ifdef CONFIG_TICK_ONESHOT
 static DEFINE_PER_CPU(struct clock_event_device *, tick_oneshot_wakeup_device);
 
-static void tick_broadcast_setup_oneshot(struct clock_event_device *bc);
+static void tick_broadcast_setup_oneshot(struct clock_event_device *bc, bool from_periodic);
 static void tick_broadcast_clear_oneshot(int cpu);
 static void tick_resume_broadcast_oneshot(struct clock_event_device *bc);
 # ifdef CONFIG_HOTPLUG_CPU
 static void tick_broadcast_oneshot_offline(unsigned int cpu);
 # endif
 #else
-static inline void tick_broadcast_setup_oneshot(struct clock_event_device *bc) { BUG(); }
+static inline void
+tick_broadcast_setup_oneshot(struct clock_event_device *bc, bool from_periodic) { BUG(); }
 static inline void tick_broadcast_clear_oneshot(int cpu) { }
 static inline void tick_resume_broadcast_oneshot(struct clock_event_device *bc) { }
 # ifdef CONFIG_HOTPLUG_CPU
@@ -264,7 +265,7 @@
 		if (tick_broadcast_device.mode == TICKDEV_MODE_PERIODIC)
 			tick_broadcast_start_periodic(bc);
 		else
-			tick_broadcast_setup_oneshot(bc);
+			tick_broadcast_setup_oneshot(bc, false);
 		ret = 1;
 	} else {
 		/*
@@ -500,7 +501,7 @@
 			if (tick_broadcast_device.mode == TICKDEV_MODE_PERIODIC)
 				tick_broadcast_start_periodic(bc);
 			else
-				tick_broadcast_setup_oneshot(bc);
+				tick_broadcast_setup_oneshot(bc, false);
 		}
 	}
 out:
@@ -1016,48 +1017,101 @@
 /**
  * tick_broadcast_setup_oneshot - setup the broadcast device
  */
-static void tick_broadcast_setup_oneshot(struct clock_event_device *bc)
+static void tick_broadcast_setup_oneshot(struct clock_event_device *bc,
+					 bool from_periodic)
 {
 	int cpu = smp_processor_id();
+	ktime_t nexttick = 0;
 
 	if (!bc)
 		return;
 
-	/* Set it up only once ! */
-	if (bc->event_handler != tick_handle_oneshot_broadcast) {
-		int was_periodic = clockevent_state_periodic(bc);
-
-		bc->event_handler = tick_handle_oneshot_broadcast;
-
+	/*
+	 * When the broadcast device was switched to oneshot by the first
+	 * CPU handling the NOHZ change, the other CPUs will reach this
+	 * code via hrtimer_run_queues() -> tick_check_oneshot_change()
+	 * too. Set up the broadcast device only once!
+	 */
+	if (bc->event_handler == tick_handle_oneshot_broadcast) {
 		/*
-		 * We must be careful here. There might be other CPUs
-		 * waiting for periodic broadcast. We need to set the
-		 * oneshot_mask bits for those and program the
-		 * broadcast device to fire.
+		 * The CPU which switched from periodic to oneshot mode
+		 * set the broadcast oneshot bit for all other CPUs which
+		 * are in the general (periodic) broadcast mask to ensure
+		 * that CPUs which wait for the periodic broadcast are
+		 * woken up.
+		 *
+		 * Clear the bit for the local CPU as the set bit would
+		 * prevent the first tick_broadcast_enter() after this CPU
+		 * switched to oneshot state to program the broadcast
+		 * device.
+		 *
+		 * This code can also be reached via tick_broadcast_control(),
+		 * but this cannot avoid the tick_broadcast_clear_oneshot()
+		 * as that would break the periodic to oneshot transition of
+		 * secondary CPUs. But that's harmless as the below only
+		 * clears already cleared bits.
 		 */
+		tick_broadcast_clear_oneshot(cpu);
+		return;
+	}
+
+
+	bc->event_handler = tick_handle_oneshot_broadcast;
+	bc->next_event = KTIME_MAX;
+
+	/*
+	 * When the tick mode is switched from periodic to oneshot it must
+	 * be ensured that CPUs which are waiting for periodic broadcast
+	 * get their wake-up at the next tick.  This is achieved by ORing
+	 * tick_broadcast_mask into tick_broadcast_oneshot_mask.
+	 *
+	 * For other callers, e.g. broadcast device replacement,
+	 * tick_broadcast_oneshot_mask must not be touched as this would
+	 * set bits for CPUs which are already NOHZ, but not idle. Their
+	 * next tick_broadcast_enter() would observe the bit set and fail
+	 * to update the expiry time and the broadcast event device.
+	 */
+	if (from_periodic) {
 		cpumask_copy(tmpmask, tick_broadcast_mask);
+		/* Remove the local CPU as it is obviously not idle */
 		cpumask_clear_cpu(cpu, tmpmask);
-		cpumask_or(tick_broadcast_oneshot_mask,
-			   tick_broadcast_oneshot_mask, tmpmask);
+		cpumask_or(tick_broadcast_oneshot_mask, tick_broadcast_oneshot_mask, tmpmask);
 
-		if (was_periodic && !cpumask_empty(tmpmask)) {
-			ktime_t nextevt = tick_get_next_period();
+		/*
+		 * Ensure that the oneshot broadcast handler will wake the
+		 * CPUs which are still waiting for periodic broadcast.
+		 */
+		nexttick = tick_get_next_period();
+		tick_broadcast_init_next_event(tmpmask, nexttick);
 
-			clockevents_switch_state(bc, CLOCK_EVT_STATE_ONESHOT);
-			tick_broadcast_init_next_event(tmpmask, nextevt);
-			tick_broadcast_set_event(bc, cpu, nextevt);
-		} else
-			bc->next_event = KTIME_MAX;
-	} else {
 		/*
-		 * The first cpu which switches to oneshot mode sets
-		 * the bit for all other cpus which are in the general
-		 * (periodic) broadcast mask. So the bit is set and
-		 * would prevent the first broadcast enter after this
-		 * to program the bc device.
+		 * If the underlying broadcast clock event device is
+		 * already in oneshot state, then there is nothing to do.
+		 * The device was already armed for the next tick
+		 * in tick_handle_broadcast_periodic()
 		 */
-		tick_broadcast_clear_oneshot(cpu);
+		if (clockevent_state_oneshot(bc))
+			return;
 	}
+
+	/*
+	 * When switching from periodic to oneshot mode arm the broadcast
+	 * device for the next tick.
+	 *
+	 * If the broadcast device has been replaced in oneshot mode and
+	 * the oneshot broadcast mask is not empty, then arm it to expire
+	 * immediately in order to reevaluate the next expiring timer.
+	 * @nexttick is 0 and therefore in the past which will cause the
+	 * clockevent code to force an event.
+	 *
+	 * For both cases the programming can be avoided when the oneshot
+	 * broadcast mask is empty.
+	 *
+	 * tick_broadcast_set_event() implicitly switches the broadcast
+	 * device to oneshot state.
+	 */
+	if (!cpumask_empty(tick_broadcast_oneshot_mask))
+		tick_broadcast_set_event(bc, cpu, nexttick);
 }
 
 /*
@@ -1066,14 +1120,16 @@
 void tick_broadcast_switch_to_oneshot(void)
 {
 	struct clock_event_device *bc;
+	enum tick_device_mode oldmode;
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&tick_broadcast_lock, flags);
 
+	oldmode = tick_broadcast_device.mode;
 	tick_broadcast_device.mode = TICKDEV_MODE_ONESHOT;
 	bc = tick_broadcast_device.evtdev;
 	if (bc)
-		tick_broadcast_setup_oneshot(bc);
+		tick_broadcast_setup_oneshot(bc, oldmode == TICKDEV_MODE_PERIODIC);
 
 	raw_spin_unlock_irqrestore(&tick_broadcast_lock, flags);
 }
@@ -1088,6 +1144,30 @@
 	bc = tick_broadcast_device.evtdev;
 
 	if (bc && broadcast_needs_cpu(bc, deadcpu)) {
+		/*
+		 * If the broadcast force bit of the current CPU is set,
+		 * then the current CPU has not yet reprogrammed the local
+		 * timer device to avoid a ping-pong race. See
+		 * ___tick_broadcast_oneshot_control().
+		 *
+		 * If the broadcast device is hrtimer based then
+		 * programming the broadcast event below does not have any
+		 * effect because the local clockevent device is not
+		 * running and not programmed because the broadcast event
+		 * is not earlier than the pending event of the local clock
+		 * event device. As a consequence all CPUs waiting for a
+		 * broadcast event are stuck forever.
+		 *
+		 * Detect this condition and reprogram the cpu local timer
+		 * device to avoid the starvation.
+		 */
+		if (tick_check_broadcast_expired()) {
+			struct tick_device *td = this_cpu_ptr(&tick_cpu_device);
+
+			cpumask_clear_cpu(smp_processor_id(), tick_broadcast_force_mask);
+			tick_program_event(td->evtdev->next_event, 1);
+		}
+
 		/* This moves the broadcast assignment to this CPU: */
 		clockevents_program_event(bc, bc->next_event, 1);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/tick-common.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/tick-common.c
@@ -179,26 +179,6 @@
 	}
 }
 
-#ifdef CONFIG_NO_HZ_FULL
-static void giveup_do_timer(void *info)
-{
-	int cpu = *(unsigned int *)info;
-
-	WARN_ON(tick_do_timer_cpu != smp_processor_id());
-
-	tick_do_timer_cpu = cpu;
-}
-
-static void tick_take_do_timer_from_boot(void)
-{
-	int cpu = smp_processor_id();
-	int from = tick_do_timer_boot_cpu;
-
-	if (from >= 0 && from != cpu)
-		smp_call_function_single(from, giveup_do_timer, &cpu, 1);
-}
-#endif
-
 /*
  * Setup the tick device
  */
@@ -219,23 +199,28 @@
 		 */
 		if (tick_do_timer_cpu == TICK_DO_TIMER_BOOT) {
 			tick_do_timer_cpu = cpu;
-
 			tick_next_period = ktime_get();
 #ifdef CONFIG_NO_HZ_FULL
 			/*
-			 * The boot CPU may be nohz_full, in which case set
-			 * tick_do_timer_boot_cpu so the first housekeeping
-			 * secondary that comes up will take do_timer from
-			 * us.
+			 * The boot CPU may be nohz_full, in which case the
+			 * first housekeeping secondary will take do_timer()
+			 * from it.
 			 */
 			if (tick_nohz_full_cpu(cpu))
 				tick_do_timer_boot_cpu = cpu;
 
-		} else if (tick_do_timer_boot_cpu != -1 &&
-						!tick_nohz_full_cpu(cpu)) {
-			tick_take_do_timer_from_boot();
+		} else if (tick_do_timer_boot_cpu != -1 && !tick_nohz_full_cpu(cpu)) {
 			tick_do_timer_boot_cpu = -1;
-			WARN_ON(tick_do_timer_cpu != cpu);
+			/*
+			 * The boot CPU will stay in periodic (NOHZ disabled)
+			 * mode until clocksource_done_booting() called after
+			 * smp_init() selects a high resolution clocksource and
+			 * timekeeping_notify() kicks the NOHZ stuff alive.
+			 *
+			 * So this WRITE_ONCE can only race with the READ_ONCE
+			 * check in tick_periodic() but this race is harmless.
+			 */
+			WRITE_ONCE(tick_do_timer_cpu, cpu);
 #endif
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/tick-sched.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/tick-sched.c
@@ -161,14 +161,27 @@
 	raw_spin_lock(&jiffies_lock);
 	write_seqcount_begin(&jiffies_seq);
 	/* Did we start the jiffies update yet ? */
-	if (last_jiffies_update == 0)
+	if (last_jiffies_update == 0) {
+		u32 rem;
+
+		/*
+		 * Ensure that the tick is aligned to a multiple of
+		 * TICK_NSEC.
+		 */
+		div_u64_rem(tick_next_period, TICK_NSEC, &rem);
+		if (rem)
+			tick_next_period += TICK_NSEC - rem;
+
 		last_jiffies_update = tick_next_period;
+	}
 	period = last_jiffies_update;
 	write_seqcount_end(&jiffies_seq);
 	raw_spin_unlock(&jiffies_lock);
 	return period;
 }
 
+#define MAX_STALLED_JIFFIES 5
+
 static void tick_sched_do_timer(struct tick_sched *ts, ktime_t now)
 {
 	int cpu = smp_processor_id();
@@ -186,7 +199,7 @@
 	 */
 	if (unlikely(tick_do_timer_cpu == TICK_DO_TIMER_NONE)) {
 #ifdef CONFIG_NO_HZ_FULL
-		WARN_ON(tick_nohz_full_running);
+		WARN_ON_ONCE(tick_nohz_full_running);
 #endif
 		tick_do_timer_cpu = cpu;
 	}
@@ -196,6 +209,21 @@
 	if (tick_do_timer_cpu == cpu)
 		tick_do_update_jiffies64(now);
 
+	/*
+	 * If jiffies update stalled for too long (timekeeper in stop_machine()
+	 * or VMEXIT'ed for several msecs), force an update.
+	 */
+	if (ts->last_tick_jiffies != jiffies) {
+		ts->stalled_jiffies = 0;
+		ts->last_tick_jiffies = READ_ONCE(jiffies);
+	} else {
+		if (++ts->stalled_jiffies == MAX_STALLED_JIFFIES) {
+			tick_do_update_jiffies64(now);
+			ts->stalled_jiffies = 0;
+			ts->last_tick_jiffies = READ_ONCE(jiffies);
+		}
+	}
+
 	if (ts->inidle)
 		ts->got_idle_tick = 1;
 }
@@ -264,6 +292,11 @@
 		return true;
 	}
 
+	if (val & TICK_DEP_MASK_RCU_EXP) {
+		trace_tick_stop(0, TICK_DEP_MASK_RCU_EXP);
+		return true;
+	}
+
 	return false;
 }
 
@@ -509,9 +542,8 @@
 	cpumask_copy(tick_nohz_full_mask, cpumask);
 	tick_nohz_full_running = true;
 }
-EXPORT_SYMBOL_GPL(tick_nohz_full_setup);
 
-static int tick_nohz_cpu_down(unsigned int cpu)
+bool tick_nohz_cpu_hotpluggable(unsigned int cpu)
 {
 	/*
 	 * The tick_do_timer_cpu CPU handles housekeeping duty (unbound
@@ -519,8 +551,13 @@
 	 * CPUs. It must remain online when nohz full is enabled.
 	 */
 	if (tick_nohz_full_running && tick_do_timer_cpu == cpu)
-		return -EBUSY;
-	return 0;
+		return false;
+	return true;
+}
+
+static int tick_nohz_cpu_down(unsigned int cpu)
+{
+	return tick_nohz_cpu_hotpluggable(cpu) ? 0 : -EBUSY;
 }
 
 void __init tick_nohz_init(void)
@@ -913,6 +950,8 @@
 	if (unlikely(expires == KTIME_MAX)) {
 		if (ts->nohz_mode == NOHZ_MODE_HIGHRES)
 			hrtimer_cancel(&ts->sched_timer);
+		else
+			tick_program_event(KTIME_MAX, 1);
 		return;
 	}
 
@@ -1319,9 +1358,15 @@
 	tick_sched_do_timer(ts, now);
 	tick_sched_handle(ts, regs);
 
-	/* No need to reprogram if we are running tickless  */
-	if (unlikely(ts->tick_stopped))
+	if (unlikely(ts->tick_stopped)) {
+		/*
+		 * The clockevent device is not reprogrammed, so change the
+		 * clock event device to ONESHOT_STOPPED to avoid spurious
+		 * interrupts on devices which might not be truly one shot.
+		 */
+		tick_program_event(KTIME_MAX, 1);
 		return;
+	}
 
 	hrtimer_forward(&ts->sched_timer, now, TICK_NSEC);
 	tick_program_event(hrtimer_get_expires(&ts->sched_timer), 1);
@@ -1375,6 +1420,13 @@
 	now = ktime_get();
 	if (ts->idle_active)
 		tick_nohz_stop_idle(ts, now);
+	/*
+	 * If all CPUs are idle. We may need to update a stale jiffies value.
+	 * Note nohz_full is a special case: a timekeeper is guaranteed to stay
+	 * alive but it might be busy looping with interrupts disabled in some
+	 * rare case (typically stop machine). So we must make sure we have a
+	 * last resort.
+	 */
 	if (ts->tick_stopped)
 		tick_nohz_update_jiffies(now);
 }
@@ -1476,13 +1528,23 @@
 void tick_cancel_sched_timer(int cpu)
 {
 	struct tick_sched *ts = &per_cpu(tick_cpu_sched, cpu);
+	ktime_t idle_sleeptime, iowait_sleeptime;
+	unsigned long idle_calls, idle_sleeps;
 
 # ifdef CONFIG_HIGH_RES_TIMERS
 	if (ts->sched_timer.base)
 		hrtimer_cancel(&ts->sched_timer);
 # endif
 
+	idle_sleeptime = ts->idle_sleeptime;
+	iowait_sleeptime = ts->iowait_sleeptime;
+	idle_calls = ts->idle_calls;
+	idle_sleeps = ts->idle_sleeps;
 	memset(ts, 0, sizeof(*ts));
+	ts->idle_sleeptime = idle_sleeptime;
+	ts->iowait_sleeptime = iowait_sleeptime;
+	ts->idle_calls = idle_calls;
+	ts->idle_sleeps = idle_sleeps;
 }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/tick-sched.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/tick-sched.h
@@ -49,6 +49,8 @@
  * @timer_expires_base:	Base time clock monotonic for @timer_expires
  * @next_timer:		Expiry time of next expiring timer for debugging purpose only
  * @tick_dep_mask:	Tick dependency mask - is set, if someone needs the tick
+ * @last_tick_jiffies:	Value of jiffies seen on last tick
+ * @stalled_jiffies:	Number of stalled jiffies detected across ticks
  */
 struct tick_sched {
 	struct hrtimer			sched_timer;
@@ -77,6 +79,8 @@
 	u64				next_timer;
 	ktime_t				idle_expires;
 	atomic_t			tick_dep_mask;
+	unsigned long			last_tick_jiffies;
+	unsigned int			stalled_jiffies;
 };
 
 extern struct tick_sched *tick_get_tick_sched(int cpu);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/time.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/time.c
@@ -539,7 +539,7 @@
  * - all other values are converted to jiffies by either multiplying
  *   the input value by a factor or dividing it with a factor and
  *   handling any 32-bit overflows.
- *   for the details see __msecs_to_jiffies()
+ *   for the details see _msecs_to_jiffies()
  *
  * msecs_to_jiffies() checks for the passed in value being a constant
  * via __builtin_constant_p() allowing gcc to eliminate most of the
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/time_test.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/time_test.c
@@ -73,7 +73,7 @@
 
 		days = div_s64(secs, 86400);
 
-		#define FAIL_MSG "%05ld/%02d/%02d (%2d) : %ld", \
+		#define FAIL_MSG "%05ld/%02d/%02d (%2d) : %lld", \
 			year, month, mdday, yday, days
 
 		KUNIT_ASSERT_EQ_MSG(test, year - 1900, result.tm_year, FAIL_MSG);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/timekeeping.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/timekeeping.c
@@ -17,11 +17,13 @@
 #include <linux/clocksource.h>
 #include <linux/jiffies.h>
 #include <linux/time.h>
+#include <linux/timex.h>
 #include <linux/tick.h>
 #include <linux/stop_machine.h>
 #include <linux/pvclock_gtod.h>
 #include <linux/compiler.h>
 #include <linux/audit.h>
+#include <linux/random.h>
 
 #include "tick-internal.h"
 #include "ntp_internal.h"
@@ -429,6 +431,14 @@
 	memcpy(base + 1, base, sizeof(*base));
 }
 
+static __always_inline u64 fast_tk_get_delta_ns(struct tk_read_base *tkr)
+{
+	u64 delta, cycles = tk_clock_read(tkr);
+
+	delta = clocksource_delta(cycles, tkr->cycle_last, tkr->mask);
+	return timekeeping_delta_to_ns(tkr, delta);
+}
+
 static __always_inline u64 __ktime_get_fast_ns(struct tk_fast *tkf)
 {
 	struct tk_read_base *tkr;
@@ -439,13 +449,8 @@
 		seq = raw_read_seqcount_latch(&tkf->seq);
 		tkr = tkf->base + (seq & 0x01);
 		now = ktime_to_ns(tkr->base);
-
-		now += timekeeping_delta_to_ns(tkr,
-				clocksource_delta(
-					tk_clock_read(tkr),
-					tkr->cycle_last,
-					tkr->mask));
-	} while (read_seqcount_latch_retry(&tkf->seq, seq));
+		now += fast_tk_get_delta_ns(tkr);
+	} while (raw_read_seqcount_latch_retry(&tkf->seq, seq));
 
 	return now;
 }
@@ -482,7 +487,7 @@
  * of the following timestamps. Callers need to be aware of that and
  * deal with it.
  */
-u64 ktime_get_mono_fast_ns(void)
+u64 notrace ktime_get_mono_fast_ns(void)
 {
 	return __ktime_get_fast_ns(&tk_fast_mono);
 }
@@ -494,7 +499,7 @@
  * Contrary to ktime_get_mono_fast_ns() this is always correct because the
  * conversion factor is not affected by NTP/PTP correction.
  */
-u64 ktime_get_raw_fast_ns(void)
+u64 notrace ktime_get_raw_fast_ns(void)
 {
 	return __ktime_get_fast_ns(&tk_fast_raw);
 }
@@ -521,7 +526,7 @@
  * partially updated.  Since the tk->offs_boot update is a rare event, this
  * should be a rare occurrence which postprocessing should be able to handle.
  *
- * The caveats vs. timestamp ordering as documented for ktime_get_fast_ns()
+ * The caveats vs. timestamp ordering as documented for ktime_get_mono_fast_ns()
  * apply as well.
  */
 u64 notrace ktime_get_boot_fast_ns(void)
@@ -543,11 +548,8 @@
 		tkr = tkf->base + (seq & 0x01);
 		basem = ktime_to_ns(tkr->base);
 		baser = ktime_to_ns(tkr->base_real);
-
-		delta = timekeeping_delta_to_ns(tkr,
-				clocksource_delta(tk_clock_read(tkr),
-				tkr->cycle_last, tkr->mask));
-	} while (read_seqcount_latch_retry(&tkf->seq, seq));
+		delta = fast_tk_get_delta_ns(tkr);
+	} while (raw_read_seqcount_latch_retry(&tkf->seq, seq));
 
 	if (mono)
 		*mono = basem + delta;
@@ -557,7 +559,7 @@
 /**
  * ktime_get_real_fast_ns: - NMI safe and fast access to clock realtime.
  *
- * See ktime_get_fast_ns() for documentation of the time stamp ordering.
+ * See ktime_get_mono_fast_ns() for documentation of the time stamp ordering.
  */
 u64 ktime_get_real_fast_ns(void)
 {
@@ -1161,13 +1163,15 @@
 }
 
 /*
- * cycle_between - true if test occurs chronologically between before and after
+ * timestamp_in_interval - true if ts is chronologically in [start, end]
+ *
+ * True if ts occurs chronologically at or after start, and before or at end.
  */
-static bool cycle_between(u64 before, u64 test, u64 after)
+static bool timestamp_in_interval(u64 start, u64 end, u64 ts)
 {
-	if (test > before && test < after)
+	if (ts >= start && ts <= end)
 		return true;
-	if (test < before && before > after)
+	if (start > end && (ts >= start || ts <= end))
 		return true;
 	return false;
 }
@@ -1227,7 +1231,7 @@
 		 */
 		now = tk_clock_read(&tk->tkr_mono);
 		interval_start = tk->tkr_mono.cycle_last;
-		if (!cycle_between(interval_start, cycles, now)) {
+		if (!timestamp_in_interval(interval_start, now, cycles)) {
 			clock_was_set_seq = tk->clock_was_set_seq;
 			cs_was_changed_seq = tk->cs_was_changed_seq;
 			cycles = interval_start;
@@ -1240,10 +1244,8 @@
 				      tk_core.timekeeper.offs_real);
 		base_raw = tk->tkr_raw.base;
 
-		nsec_real = timekeeping_cycles_to_ns(&tk->tkr_mono,
-						     system_counterval.cycles);
-		nsec_raw = timekeeping_cycles_to_ns(&tk->tkr_raw,
-						    system_counterval.cycles);
+		nsec_real = timekeeping_cycles_to_ns(&tk->tkr_mono, cycles);
+		nsec_raw = timekeeping_cycles_to_ns(&tk->tkr_raw, cycles);
 	} while (read_seqcount_retry(&tk_core.seq, seq));
 
 	xtstamp->sys_realtime = ktime_add_ns(base_real, nsec_real);
@@ -1258,13 +1260,13 @@
 		bool discontinuity;
 
 		/*
-		 * Check that the counter value occurs after the provided
+		 * Check that the counter value is not before the provided
 		 * history reference and that the history doesn't cross a
 		 * clocksource change
 		 */
 		if (!history_begin ||
-		    !cycle_between(history_begin->cycles,
-				   system_counterval.cycles, cycles) ||
+		    !timestamp_in_interval(history_begin->cycles,
+					   cycles, system_counterval.cycles) ||
 		    history_begin->cs_was_changed_seq != cs_was_changed_seq)
 			return -EINVAL;
 		partial_history_cycles = cycles - system_counterval.cycles;
@@ -1306,8 +1308,7 @@
 	timekeeping_forward_now(tk);
 
 	xt = tk_xtime(tk);
-	ts_delta.tv_sec = ts->tv_sec - xt.tv_sec;
-	ts_delta.tv_nsec = ts->tv_nsec - xt.tv_nsec;
+	ts_delta = timespec64_sub(*ts, xt);
 
 	if (timespec64_compare(&tk->wall_to_monotonic, &ts_delta) > 0) {
 		ret = -EINVAL;
@@ -1326,8 +1327,10 @@
 	/* Signal hrtimers about time change */
 	clock_was_set(CLOCK_SET_WALL);
 
-	if (!ret)
+	if (!ret) {
 		audit_tk_injoffset(ts_delta);
+		add_device_randomness(ts, sizeof(*ts));
+	}
 
 	return ret;
 }
@@ -2381,6 +2384,20 @@
 	return 0;
 }
 
+/**
+ * random_get_entropy_fallback - Returns the raw clock source value,
+ * used by random.c for platforms with no valid random_get_entropy().
+ */
+unsigned long random_get_entropy_fallback(void)
+{
+	struct tk_read_base *tkr = &tk_core.timekeeper.tkr_mono;
+	struct clocksource *clock = READ_ONCE(tkr->clock);
+
+	if (unlikely(timekeeping_suspended || !clock))
+		return 0;
+	return clock->read(clock);
+}
+EXPORT_SYMBOL_GPL(random_get_entropy_fallback);
 
 /**
  * do_adjtimex() - Accessor function to NTP __do_adjtimex function
@@ -2399,6 +2416,7 @@
 	ret = timekeeping_validate_timex(txc);
 	if (ret)
 		return ret;
+	add_device_randomness(txc, sizeof(*txc));
 
 	if (txc->modes & ADJ_SETOFFSET) {
 		struct timespec64 delta;
@@ -2416,6 +2434,7 @@
 	audit_ntp_init(&ad);
 
 	ktime_get_real_ts64(&ts);
+	add_device_randomness(&ts, sizeof(ts));
 
 	raw_spin_lock_irqsave(&timekeeper_lock, flags);
 	write_seqcount_begin(&tk_core.seq);
@@ -2440,7 +2459,7 @@
 		clock_set |= timekeeping_advance(TK_ADV_FREQ);
 
 	if (clock_set)
-		clock_was_set(CLOCK_REALTIME);
+		clock_was_set(CLOCK_SET_WALL);
 
 	ntp_notify_cmos_timer();
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/time/timer.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/time/timer.c
@@ -964,7 +964,7 @@
 	unsigned int idx = UINT_MAX;
 	int ret = 0;
 
-	BUG_ON(!timer->function);
+	debug_assert_init(timer);
 
 	/*
 	 * This is a common optimization triggered by the networking code - if
@@ -991,6 +991,14 @@
 		 * dequeue/enqueue dance.
 		 */
 		base = lock_timer_base(timer, &flags);
+		/*
+		 * Has @timer been shutdown? This needs to be evaluated
+		 * while holding base lock to prevent a race against the
+		 * shutdown code.
+		 */
+		if (!timer->function)
+			goto out_unlock;
+
 		forward_timer_base(base);
 
 		if (timer_pending(timer) && (options & MOD_TIMER_REDUCE) &&
@@ -1017,6 +1025,14 @@
 		}
 	} else {
 		base = lock_timer_base(timer, &flags);
+		/*
+		 * Has @timer been shutdown? This needs to be evaluated
+		 * while holding base lock to prevent a race against the
+		 * shutdown code.
+		 */
+		if (!timer->function)
+			goto out_unlock;
+
 		forward_timer_base(base);
 	}
 
@@ -1030,7 +1046,7 @@
 		/*
 		 * We are trying to schedule the timer on the new base.
 		 * However we can't change timer's base while it is running,
-		 * otherwise del_timer_sync() can't detect that the timer's
+		 * otherwise timer_delete_sync() can't detect that the timer's
 		 * handler yet has not finished. This also guarantees that the
 		 * timer is serialized wrt itself.
 		 */
@@ -1068,14 +1084,20 @@
 }
 
 /**
- * mod_timer_pending - modify a pending timer's timeout
- * @timer: the pending timer to be modified
- * @expires: new timeout in jiffies
- *
- * mod_timer_pending() is the same for pending timers as mod_timer(),
- * but will not re-activate and modify already deleted timers.
- *
- * It is useful for unserialized use of timers.
+ * mod_timer_pending - Modify a pending timer's timeout
+ * @timer:	The pending timer to be modified
+ * @expires:	New absolute timeout in jiffies
+ *
+ * mod_timer_pending() is the same for pending timers as mod_timer(), but
+ * will not activate inactive timers.
+ *
+ * If @timer->function == NULL then the start operation is silently
+ * discarded.
+ *
+ * Return:
+ * * %0 - The timer was inactive and not modified or was in
+ *	  shutdown state and the operation was discarded
+ * * %1 - The timer was active and requeued to expire at @expires
  */
 int mod_timer_pending(struct timer_list *timer, unsigned long expires)
 {
@@ -1084,24 +1106,31 @@
 EXPORT_SYMBOL(mod_timer_pending);
 
 /**
- * mod_timer - modify a timer's timeout
- * @timer: the timer to be modified
- * @expires: new timeout in jiffies
- *
- * mod_timer() is a more efficient way to update the expire field of an
- * active timer (if the timer is inactive it will be activated)
+ * mod_timer - Modify a timer's timeout
+ * @timer:	The timer to be modified
+ * @expires:	New absolute timeout in jiffies
  *
  * mod_timer(timer, expires) is equivalent to:
  *
  *     del_timer(timer); timer->expires = expires; add_timer(timer);
  *
+ * mod_timer() is more efficient than the above open coded sequence. In
+ * case that the timer is inactive, the del_timer() part is a NOP. The
+ * timer is in any case activated with the new expiry time @expires.
+ *
  * Note that if there are multiple unserialized concurrent users of the
  * same timer, then mod_timer() is the only safe way to modify the timeout,
  * since add_timer() cannot modify an already running timer.
  *
- * The function returns whether it has modified a pending timer or not.
- * (ie. mod_timer() of an inactive timer returns 0, mod_timer() of an
- * active timer returns 1.)
+ * If @timer->function == NULL then the start operation is silently
+ * discarded. In this case the return value is 0 and meaningless.
+ *
+ * Return:
+ * * %0 - The timer was inactive and started or was in shutdown
+ *	  state and the operation was discarded
+ * * %1 - The timer was active and requeued to expire at @expires or
+ *	  the timer was active and not modified because @expires did
+ *	  not change the effective expiry time
  */
 int mod_timer(struct timer_list *timer, unsigned long expires)
 {
@@ -1112,11 +1141,22 @@
 /**
  * timer_reduce - Modify a timer's timeout if it would reduce the timeout
  * @timer:	The timer to be modified
- * @expires:	New timeout in jiffies
+ * @expires:	New absolute timeout in jiffies
  *
  * timer_reduce() is very similar to mod_timer(), except that it will only
- * modify a running timer if that would reduce the expiration time (it will
- * start a timer that isn't running).
+ * modify an enqueued timer if that would reduce the expiration time. If
+ * @timer is not enqueued it starts the timer.
+ *
+ * If @timer->function == NULL then the start operation is silently
+ * discarded.
+ *
+ * Return:
+ * * %0 - The timer was inactive and started or was in shutdown
+ *	  state and the operation was discarded
+ * * %1 - The timer was active and requeued to expire at @expires or
+ *	  the timer was active and not modified because @expires
+ *	  did not change the effective expiry time such that the
+ *	  timer would expire earlier than already scheduled
  */
 int timer_reduce(struct timer_list *timer, unsigned long expires)
 {
@@ -1125,39 +1165,51 @@
 EXPORT_SYMBOL(timer_reduce);
 
 /**
- * add_timer - start a timer
- * @timer: the timer to be added
+ * add_timer - Start a timer
+ * @timer:	The timer to be started
  *
- * The kernel will do a ->function(@timer) callback from the
- * timer interrupt at the ->expires point in the future. The
- * current time is 'jiffies'.
+ * Start @timer to expire at @timer->expires in the future. @timer->expires
+ * is the absolute expiry time measured in 'jiffies'. When the timer expires
+ * timer->function(timer) will be invoked from soft interrupt context.
  *
- * The timer's ->expires, ->function fields must be set prior calling this
- * function.
+ * The @timer->expires and @timer->function fields must be set prior
+ * to calling this function.
+ *
+ * If @timer->function == NULL then the start operation is silently
+ * discarded.
  *
- * Timers with an ->expires field in the past will be executed in the next
- * timer tick.
+ * If @timer->expires is already in the past @timer will be queued to
+ * expire at the next timer tick.
+ *
+ * This can only operate on an inactive timer. Attempts to invoke this on
+ * an active timer are rejected with a warning.
  */
 void add_timer(struct timer_list *timer)
 {
-	BUG_ON(timer_pending(timer));
+	if (WARN_ON_ONCE(timer_pending(timer)))
+		return;
 	__mod_timer(timer, timer->expires, MOD_TIMER_NOTPENDING);
 }
 EXPORT_SYMBOL(add_timer);
 
 /**
- * add_timer_on - start a timer on a particular CPU
- * @timer: the timer to be added
- * @cpu: the CPU to start it on
+ * add_timer_on - Start a timer on a particular CPU
+ * @timer:	The timer to be started
+ * @cpu:	The CPU to start it on
  *
- * This is not very scalable on SMP. Double adds are not possible.
+ * Same as add_timer() except that it starts the timer on the given CPU.
+ *
+ * See add_timer() for further details.
  */
 void add_timer_on(struct timer_list *timer, int cpu)
 {
 	struct timer_base *new_base, *base;
 	unsigned long flags;
 
-	BUG_ON(timer_pending(timer) || !timer->function);
+	debug_assert_init(timer);
+
+	if (WARN_ON_ONCE(timer_pending(timer)))
+		return;
 
 	new_base = get_timer_cpu_base(timer->flags, cpu);
 
@@ -1167,6 +1219,13 @@
 	 * wrong base locked.  See lock_timer_base().
 	 */
 	base = lock_timer_base(timer, &flags);
+	/*
+	 * Has @timer been shutdown? This needs to be evaluated while
+	 * holding base lock to prevent a race against the shutdown code.
+	 */
+	if (!timer->function)
+		goto out_unlock;
+
 	if (base != new_base) {
 		timer->flags |= TIMER_MIGRATING;
 
@@ -1180,22 +1239,27 @@
 
 	debug_timer_activate(timer);
 	internal_add_timer(base, timer);
+out_unlock:
 	raw_spin_unlock_irqrestore(&base->lock, flags);
 }
 EXPORT_SYMBOL_GPL(add_timer_on);
 
 /**
- * del_timer - deactivate a timer.
- * @timer: the timer to be deactivated
- *
- * del_timer() deactivates a timer - this works on both active and inactive
- * timers.
- *
- * The function returns whether it has deactivated a pending timer or not.
- * (ie. del_timer() of an inactive timer returns 0, del_timer() of an
- * active timer returns 1.)
+ * __timer_delete - Internal function: Deactivate a timer
+ * @timer:	The timer to be deactivated
+ * @shutdown:	If true, this indicates that the timer is about to be
+ *		shutdown permanently.
+ *
+ * If @shutdown is true then @timer->function is set to NULL under the
+ * timer base lock which prevents further rearming of the time. In that
+ * case any attempt to rearm @timer after this function returns will be
+ * silently ignored.
+ *
+ * Return:
+ * * %0 - The timer was not pending
+ * * %1 - The timer was pending and deactivated
  */
-int del_timer(struct timer_list *timer)
+static int __timer_delete(struct timer_list *timer, bool shutdown)
 {
 	struct timer_base *base;
 	unsigned long flags;
@@ -1203,24 +1267,90 @@
 
 	debug_assert_init(timer);
 
-	if (timer_pending(timer)) {
+	/*
+	 * If @shutdown is set then the lock has to be taken whether the
+	 * timer is pending or not to protect against a concurrent rearm
+	 * which might hit between the lockless pending check and the lock
+	 * aquisition. By taking the lock it is ensured that such a newly
+	 * enqueued timer is dequeued and cannot end up with
+	 * timer->function == NULL in the expiry code.
+	 *
+	 * If timer->function is currently executed, then this makes sure
+	 * that the callback cannot requeue the timer.
+	 */
+	if (timer_pending(timer) || shutdown) {
 		base = lock_timer_base(timer, &flags);
 		ret = detach_if_pending(timer, base, true);
+		if (shutdown)
+			timer->function = NULL;
 		raw_spin_unlock_irqrestore(&base->lock, flags);
 	}
 
 	return ret;
 }
-EXPORT_SYMBOL(del_timer);
 
 /**
- * try_to_del_timer_sync - Try to deactivate a timer
- * @timer: timer to delete
+ * timer_delete - Deactivate a timer
+ * @timer:	The timer to be deactivated
  *
- * This function tries to deactivate a timer. Upon successful (ret >= 0)
- * exit the timer is not queued and the handler is not running on any CPU.
+ * The function only deactivates a pending timer, but contrary to
+ * timer_delete_sync() it does not take into account whether the timer's
+ * callback function is concurrently executed on a different CPU or not.
+ * It neither prevents rearming of the timer.  If @timer can be rearmed
+ * concurrently then the return value of this function is meaningless.
+ *
+ * Return:
+ * * %0 - The timer was not pending
+ * * %1 - The timer was pending and deactivated
  */
-int try_to_del_timer_sync(struct timer_list *timer)
+int timer_delete(struct timer_list *timer)
+{
+	return __timer_delete(timer, false);
+}
+EXPORT_SYMBOL(timer_delete);
+
+/**
+ * timer_shutdown - Deactivate a timer and prevent rearming
+ * @timer:	The timer to be deactivated
+ *
+ * The function does not wait for an eventually running timer callback on a
+ * different CPU but it prevents rearming of the timer. Any attempt to arm
+ * @timer after this function returns will be silently ignored.
+ *
+ * This function is useful for teardown code and should only be used when
+ * timer_shutdown_sync() cannot be invoked due to locking or context constraints.
+ *
+ * Return:
+ * * %0 - The timer was not pending
+ * * %1 - The timer was pending
+ */
+int timer_shutdown(struct timer_list *timer)
+{
+	return __timer_delete(timer, true);
+}
+EXPORT_SYMBOL_GPL(timer_shutdown);
+
+/**
+ * __try_to_del_timer_sync - Internal function: Try to deactivate a timer
+ * @timer:	Timer to deactivate
+ * @shutdown:	If true, this indicates that the timer is about to be
+ *		shutdown permanently.
+ *
+ * If @shutdown is true then @timer->function is set to NULL under the
+ * timer base lock which prevents further rearming of the timer. Any
+ * attempt to rearm @timer after this function returns will be silently
+ * ignored.
+ *
+ * This function cannot guarantee that the timer cannot be rearmed
+ * right after dropping the base lock if @shutdown is false. That
+ * needs to be prevented by the calling code if necessary.
+ *
+ * Return:
+ * * %0  - The timer was not pending
+ * * %1  - The timer was pending and deactivated
+ * * %-1 - The timer callback function is running on a different CPU
+ */
+static int __try_to_del_timer_sync(struct timer_list *timer, bool shutdown)
 {
 	struct timer_base *base;
 	unsigned long flags;
@@ -1232,11 +1362,34 @@
 
 	if (base->running_timer != timer)
 		ret = detach_if_pending(timer, base, true);
+	if (shutdown)
+		timer->function = NULL;
 
 	raw_spin_unlock_irqrestore(&base->lock, flags);
 
 	return ret;
 }
+
+/**
+ * try_to_del_timer_sync - Try to deactivate a timer
+ * @timer:	Timer to deactivate
+ *
+ * This function tries to deactivate a timer. On success the timer is not
+ * queued and the timer callback function is not running on any CPU.
+ *
+ * This function does not guarantee that the timer cannot be rearmed right
+ * after dropping the base lock. That needs to be prevented by the calling
+ * code if necessary.
+ *
+ * Return:
+ * * %0  - The timer was not pending
+ * * %1  - The timer was pending and deactivated
+ * * %-1 - The timer callback function is running on a different CPU
+ */
+int try_to_del_timer_sync(struct timer_list *timer)
+{
+	return __try_to_del_timer_sync(timer, false);
+}
 EXPORT_SYMBOL(try_to_del_timer_sync);
 
 #ifdef CONFIG_PREEMPT_RT
@@ -1312,44 +1465,29 @@
 static inline void del_timer_wait_running(struct timer_list *timer) { }
 #endif
 
-#if defined(CONFIG_SMP) || defined(CONFIG_PREEMPT_RT)
 /**
- * del_timer_sync - deactivate a timer and wait for the handler to finish.
- * @timer: the timer to be deactivated
- *
- * This function only differs from del_timer() on SMP: besides deactivating
- * the timer it also makes sure the handler has finished executing on other
- * CPUs.
- *
- * Synchronization rules: Callers must prevent restarting of the timer,
- * otherwise this function is meaningless. It must not be called from
- * interrupt contexts unless the timer is an irqsafe one. The caller must
- * not hold locks which would prevent completion of the timer's
- * handler. The timer's handler must not call add_timer_on(). Upon exit the
- * timer is not queued and the handler is not running on any CPU.
- *
- * Note: For !irqsafe timers, you must not hold locks that are held in
- *   interrupt context while calling this function. Even if the lock has
- *   nothing to do with the timer in question.  Here's why::
- *
- *    CPU0                             CPU1
- *    ----                             ----
- *                                     <SOFTIRQ>
- *                                       call_timer_fn();
- *                                       base->running_timer = mytimer;
- *    spin_lock_irq(somelock);
- *                                     <IRQ>
- *                                        spin_lock(somelock);
- *    del_timer_sync(mytimer);
- *    while (base->running_timer == mytimer);
- *
- * Now del_timer_sync() will never return and never release somelock.
- * The interrupt on the other CPU is waiting to grab somelock but
- * it has interrupted the softirq that CPU0 is waiting to finish.
- *
- * The function returns whether it has deactivated a pending timer or not.
+ * __timer_delete_sync - Internal function: Deactivate a timer and wait
+ *			 for the handler to finish.
+ * @timer:	The timer to be deactivated
+ * @shutdown:	If true, @timer->function will be set to NULL under the
+ *		timer base lock which prevents rearming of @timer
+ *
+ * If @shutdown is not set the timer can be rearmed later. If the timer can
+ * be rearmed concurrently, i.e. after dropping the base lock then the
+ * return value is meaningless.
+ *
+ * If @shutdown is set then @timer->function is set to NULL under timer
+ * base lock which prevents rearming of the timer. Any attempt to rearm
+ * a shutdown timer is silently ignored.
+ *
+ * If the timer should be reused after shutdown it has to be initialized
+ * again.
+ *
+ * Return:
+ * * %0	- The timer was not pending
+ * * %1	- The timer was pending and deactivated
  */
-int del_timer_sync(struct timer_list *timer)
+static int __timer_delete_sync(struct timer_list *timer, bool shutdown)
 {
 	int ret;
 
@@ -1369,7 +1507,7 @@
 	 * don't use it in hardirq context, because it
 	 * could lead to deadlock.
 	 */
-	WARN_ON(in_irq() && !(timer->flags & TIMER_IRQSAFE));
+	WARN_ON(in_hardirq() && !(timer->flags & TIMER_IRQSAFE));
 
 	/*
 	 * Must be able to sleep on PREEMPT_RT because of the slowpath in
@@ -1379,7 +1517,7 @@
 		lockdep_assert_preemption_enabled();
 
 	do {
-		ret = try_to_del_timer_sync(timer);
+		ret = __try_to_del_timer_sync(timer, shutdown);
 
 		if (unlikely(ret < 0)) {
 			del_timer_wait_running(timer);
@@ -1389,8 +1527,96 @@
 
 	return ret;
 }
-EXPORT_SYMBOL(del_timer_sync);
-#endif
+
+/**
+ * timer_delete_sync - Deactivate a timer and wait for the handler to finish.
+ * @timer:	The timer to be deactivated
+ *
+ * Synchronization rules: Callers must prevent restarting of the timer,
+ * otherwise this function is meaningless. It must not be called from
+ * interrupt contexts unless the timer is an irqsafe one. The caller must
+ * not hold locks which would prevent completion of the timer's callback
+ * function. The timer's handler must not call add_timer_on(). Upon exit
+ * the timer is not queued and the handler is not running on any CPU.
+ *
+ * For !irqsafe timers, the caller must not hold locks that are held in
+ * interrupt context. Even if the lock has nothing to do with the timer in
+ * question.  Here's why::
+ *
+ *    CPU0                             CPU1
+ *    ----                             ----
+ *                                     <SOFTIRQ>
+ *                                       call_timer_fn();
+ *                                       base->running_timer = mytimer;
+ *    spin_lock_irq(somelock);
+ *                                     <IRQ>
+ *                                        spin_lock(somelock);
+ *    timer_delete_sync(mytimer);
+ *    while (base->running_timer == mytimer);
+ *
+ * Now timer_delete_sync() will never return and never release somelock.
+ * The interrupt on the other CPU is waiting to grab somelock but it has
+ * interrupted the softirq that CPU0 is waiting to finish.
+ *
+ * This function cannot guarantee that the timer is not rearmed again by
+ * some concurrent or preempting code, right after it dropped the base
+ * lock. If there is the possibility of a concurrent rearm then the return
+ * value of the function is meaningless.
+ *
+ * If such a guarantee is needed, e.g. for teardown situations then use
+ * timer_shutdown_sync() instead.
+ *
+ * Return:
+ * * %0	- The timer was not pending
+ * * %1	- The timer was pending and deactivated
+ */
+int timer_delete_sync(struct timer_list *timer)
+{
+	return __timer_delete_sync(timer, false);
+}
+EXPORT_SYMBOL(timer_delete_sync);
+
+/**
+ * timer_shutdown_sync - Shutdown a timer and prevent rearming
+ * @timer: The timer to be shutdown
+ *
+ * When the function returns it is guaranteed that:
+ *   - @timer is not queued
+ *   - The callback function of @timer is not running
+ *   - @timer cannot be enqueued again. Any attempt to rearm
+ *     @timer is silently ignored.
+ *
+ * See timer_delete_sync() for synchronization rules.
+ *
+ * This function is useful for final teardown of an infrastructure where
+ * the timer is subject to a circular dependency problem.
+ *
+ * A common pattern for this is a timer and a workqueue where the timer can
+ * schedule work and work can arm the timer. On shutdown the workqueue must
+ * be destroyed and the timer must be prevented from rearming. Unless the
+ * code has conditionals like 'if (mything->in_shutdown)' to prevent that
+ * there is no way to get this correct with timer_delete_sync().
+ *
+ * timer_shutdown_sync() is solving the problem. The correct ordering of
+ * calls in this case is:
+ *
+ *	timer_shutdown_sync(&mything->timer);
+ *	workqueue_destroy(&mything->workqueue);
+ *
+ * After this 'mything' can be safely freed.
+ *
+ * This obviously implies that the timer is not required to be functional
+ * for the rest of the shutdown operation.
+ *
+ * Return:
+ * * %0 - The timer was not pending
+ * * %1 - The timer was pending
+ */
+int timer_shutdown_sync(struct timer_list *timer)
+{
+	return __timer_delete_sync(timer, true);
+}
+EXPORT_SYMBOL_GPL(timer_shutdown_sync);
 
 static void call_timer_fn(struct timer_list *timer,
 			  void (*fn)(struct timer_list *),
@@ -1412,8 +1638,8 @@
 #endif
 	/*
 	 * Couple the lock chain with the lock chain at
-	 * del_timer_sync() by acquiring the lock_map around the fn()
-	 * call here and in del_timer_sync().
+	 * timer_delete_sync() by acquiring the lock_map around the fn()
+	 * call here and in timer_delete_sync().
 	 */
 	lock_map_acquire(&lockdep_map);
 
@@ -1456,6 +1682,12 @@
 
 		fn = timer->function;
 
+		if (WARN_ON_ONCE(!fn)) {
+			/* Should never happen. Emphasis on should! */
+			base->running_timer = NULL;
+			continue;
+		}
+
 		if (timer->flags & TIMER_IRQSAFE) {
 			raw_spin_unlock(&base->lock);
 			call_timer_fn(timer, fn, baseclk);
@@ -1722,11 +1954,14 @@
 	       time_after_eq(jiffies, base->next_expiry)) {
 		levels = collect_expired_timers(base, heads);
 		/*
-		 * The only possible reason for not finding any expired
-		 * timer at this clk is that all matching timers have been
-		 * dequeued.
+		 * The two possible reasons for not finding any expired
+		 * timer at this clk are that all matching timers have been
+		 * dequeued or no timer has been queued since
+		 * base::next_expiry was set to base::clk +
+		 * NEXT_TIMER_MAX_DELTA.
 		 */
-		WARN_ON_ONCE(!levels && !base->next_expiry_recalc);
+		WARN_ON_ONCE(!levels && !base->next_expiry_recalc
+			     && base->timers_pending);
 		base->clk++;
 		base->next_expiry = __next_timer_interrupt(base);
 
@@ -1962,8 +2197,6 @@
 	struct timer_base *new_base;
 	int b, i;
 
-	BUG_ON(cpu_online(cpu));
-
 	for (b = 0; b < NR_BASES; b++) {
 		old_base = per_cpu_ptr(&timer_bases[b], cpu);
 		new_base = get_cpu_ptr(&timer_bases[b]);
@@ -1980,7 +2213,8 @@
 		 */
 		forward_timer_base(new_base);
 
-		BUG_ON(old_base->running_timer);
+		WARN_ON_ONCE(old_base->running_timer);
+		old_base->running_timer = NULL;
 
 		for (i = 0; i < WHEEL_SIZE; i++)
 			migrate_timer_list(new_base, old_base->vectors + i);
@@ -2054,26 +2288,28 @@
 EXPORT_SYMBOL(msleep_interruptible);
 
 /**
- * usleep_range - Sleep for an approximate time
- * @min: Minimum time in usecs to sleep
- * @max: Maximum time in usecs to sleep
+ * usleep_range_state - Sleep for an approximate time in a given state
+ * @min:	Minimum time in usecs to sleep
+ * @max:	Maximum time in usecs to sleep
+ * @state:	State of the current task that will be while sleeping
  *
  * In non-atomic context where the exact wakeup time is flexible, use
- * usleep_range() instead of udelay().  The sleep improves responsiveness
+ * usleep_range_state() instead of udelay().  The sleep improves responsiveness
  * by avoiding the CPU-hogging busy-wait of udelay(), and the range reduces
  * power usage by allowing hrtimers to take advantage of an already-
  * scheduled interrupt instead of scheduling a new one just for this sleep.
  */
-void __sched usleep_range(unsigned long min, unsigned long max)
+void __sched usleep_range_state(unsigned long min, unsigned long max,
+				unsigned int state)
 {
 	ktime_t exp = ktime_add_us(ktime_get(), min);
 	u64 delta = (u64)(max - min) * NSEC_PER_USEC;
 
 	for (;;) {
-		__set_current_state(TASK_UNINTERRUPTIBLE);
+		__set_current_state(state);
 		/* Do not return before the requested sleep time has elapsed */
 		if (!schedule_hrtimeout_range(&exp, delta, HRTIMER_MODE_ABS))
 			break;
 	}
 }
-EXPORT_SYMBOL(usleep_range);
+EXPORT_SYMBOL(usleep_range_state);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/torture.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/torture.c
@@ -915,7 +915,7 @@
 	VERBOSE_TOROUT_STRING(buf);
 	while (!kthread_should_stop()) {
 		torture_shutdown_absorb(title);
-		schedule_timeout_uninterruptible(1);
+		schedule_timeout_uninterruptible(HZ / 20);
 	}
 }
 EXPORT_SYMBOL_GPL(torture_kthread_stopping);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/Kconfig
@@ -328,6 +328,7 @@
 config HWLAT_TRACER
 	bool "Tracer to detect hardware latencies (like SMIs)"
 	select GENERIC_TRACER
+	select TRACER_MAX_TRACE
 	help
 	 This tracer, when enabled will create one or more kernel threads,
 	 depending on what the cpumask file is set to, which each thread
@@ -363,6 +364,7 @@
 config OSNOISE_TRACER
 	bool "OS Noise tracer"
 	select GENERIC_TRACER
+	select TRACER_MAX_TRACE
 	help
 	  In the context of high-performance computing (HPC), the Operating
 	  System Noise (osnoise) refers to the interference experienced by an
@@ -989,7 +991,7 @@
 
 config SYNTH_EVENT_GEN_TEST
 	tristate "Test module for in-kernel synthetic event generation"
-	depends on SYNTH_EVENTS
+	depends on SYNTH_EVENTS && m
 	help
           This option creates a test module to check the base
           functionality of in-kernel synthetic event definition and
@@ -1002,7 +1004,7 @@
 
 config KPROBE_EVENT_GEN_TEST
 	tristate "Test module for in-kernel kprobe event generation"
-	depends on KPROBE_EVENTS
+	depends on KPROBE_EVENTS && m
 	help
           This option creates a test module to check the base
           functionality of in-kernel kprobe event definition.
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/Makefile
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/Makefile
@@ -47,6 +47,7 @@
 obj-$(CONFIG_TRACING) += trace_seq.o
 obj-$(CONFIG_TRACING) += trace_stat.o
 obj-$(CONFIG_TRACING) += trace_printk.o
+obj-$(CONFIG_TRACING) += 	pid_list.o
 obj-$(CONFIG_TRACING_MAP) += tracing_map.o
 obj-$(CONFIG_PREEMPTIRQ_DELAY_TEST) += preemptirq_delay_test.o
 obj-$(CONFIG_SYNTH_EVENT_GEN_TEST) += synth_event_gen_test.o
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/blktrace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/blktrace.c
@@ -310,10 +310,20 @@
 	local_irq_restore(flags);
 }
 
-static void blk_trace_free(struct blk_trace *bt)
+static void blk_trace_free(struct request_queue *q, struct blk_trace *bt)
 {
 	relay_close(bt->rchan);
-	debugfs_remove(bt->dir);
+
+	/*
+	 * If 'bt->dir' is not set, then both 'dropped' and 'msg' are created
+	 * under 'q->debugfs_dir', thus lookup and remove them.
+	 */
+	if (!bt->dir) {
+		debugfs_lookup_and_remove("dropped", q->debugfs_dir);
+		debugfs_lookup_and_remove("msg", q->debugfs_dir);
+	} else {
+		debugfs_remove(bt->dir);
+	}
 	free_percpu(bt->sequence);
 	free_percpu(bt->msg_data);
 	kfree(bt);
@@ -335,10 +345,10 @@
 	mutex_unlock(&blk_probe_mutex);
 }
 
-static void blk_trace_cleanup(struct blk_trace *bt)
+static void blk_trace_cleanup(struct request_queue *q, struct blk_trace *bt)
 {
 	synchronize_rcu();
-	blk_trace_free(bt);
+	blk_trace_free(q, bt);
 	put_probe_ref();
 }
 
@@ -352,7 +362,7 @@
 		return -EINVAL;
 
 	if (bt->trace_state != Blktrace_running)
-		blk_trace_cleanup(bt);
+		blk_trace_cleanup(q, bt);
 
 	return 0;
 }
@@ -572,7 +582,7 @@
 	ret = 0;
 err:
 	if (ret)
-		blk_trace_free(bt);
+		blk_trace_free(q, bt);
 	return ret;
 }
 
@@ -1048,7 +1058,7 @@
 	r.sector_from = cpu_to_be64(from);
 
 	__blk_add_trace(bt, blk_rq_pos(rq), blk_rq_bytes(rq),
-			rq_data_dir(rq), 0, BLK_TA_REMAP, 0,
+			req_op(rq), rq->cmd_flags, BLK_TA_REMAP, 0,
 			sizeof(r), &r, blk_trace_request_get_cgid(rq));
 	rcu_read_unlock();
 }
@@ -1537,7 +1547,8 @@
 
 static enum print_line_t blk_tracer_print_line(struct trace_iterator *iter)
 {
-	if (!(blk_tracer_flags.val & TRACE_BLK_OPT_CLASSIC))
+	if ((iter->ent->type != TRACE_BLK) ||
+	    !(blk_tracer_flags.val & TRACE_BLK_OPT_CLASSIC))
 		return TRACE_TYPE_UNHANDLED;
 
 	return print_one_line(iter, true);
@@ -1615,7 +1626,7 @@
 
 	put_probe_ref();
 	synchronize_rcu();
-	blk_trace_free(bt);
+	blk_trace_free(q, bt);
 	return 0;
 }
 
@@ -1646,7 +1657,7 @@
 	return 0;
 
 free_bt:
-	blk_trace_free(bt);
+	blk_trace_free(q, bt);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/bpf_trace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/bpf_trace.c
@@ -345,7 +345,7 @@
 	.gpl_only	= true,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_ANYTHING,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 };
 
@@ -360,8 +360,6 @@
 	return &bpf_probe_write_user_proto;
 }
 
-static DEFINE_RAW_SPINLOCK(trace_printk_lock);
-
 #define MAX_TRACE_PRINTK_VARARGS	3
 #define BPF_TRACE_PRINTK_SIZE		1024
 
@@ -369,23 +367,22 @@
 	   u64, arg2, u64, arg3)
 {
 	u64 args[MAX_TRACE_PRINTK_VARARGS] = { arg1, arg2, arg3 };
-	u32 *bin_args;
-	static char buf[BPF_TRACE_PRINTK_SIZE];
-	unsigned long flags;
+	struct bpf_bprintf_data data = {
+		.get_bin_args	= true,
+		.get_buf	= true,
+	};
 	int ret;
 
-	ret = bpf_bprintf_prepare(fmt, fmt_size, args, &bin_args,
-				  MAX_TRACE_PRINTK_VARARGS);
+	ret = bpf_bprintf_prepare(fmt, fmt_size, args,
+				  MAX_TRACE_PRINTK_VARARGS, &data);
 	if (ret < 0)
 		return ret;
 
-	raw_spin_lock_irqsave(&trace_printk_lock, flags);
-	ret = bstr_printf(buf, sizeof(buf), fmt, bin_args);
+	ret = bstr_printf(data.buf, MAX_BPRINTF_BUF, fmt, data.bin_args);
 
-	trace_bpf_trace_printk(buf);
-	raw_spin_unlock_irqrestore(&trace_printk_lock, flags);
+	trace_bpf_trace_printk(data.buf);
 
-	bpf_bprintf_cleanup();
+	bpf_bprintf_cleanup(&data);
 
 	return ret;
 }
@@ -394,7 +391,7 @@
 	.func		= bpf_trace_printk,
 	.gpl_only	= true,
 	.ret_type	= RET_INTEGER,
-	.arg1_type	= ARG_PTR_TO_MEM,
+	.arg1_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg2_type	= ARG_CONST_SIZE,
 };
 
@@ -414,26 +411,26 @@
 	return &bpf_trace_printk_proto;
 }
 
-#define MAX_SEQ_PRINTF_VARARGS		12
-
 BPF_CALL_5(bpf_seq_printf, struct seq_file *, m, char *, fmt, u32, fmt_size,
-	   const void *, data, u32, data_len)
+	   const void *, args, u32, data_len)
 {
+	struct bpf_bprintf_data data = {
+		.get_bin_args	= true,
+	};
 	int err, num_args;
-	u32 *bin_args;
 
-	if (data_len & 7 || data_len > MAX_SEQ_PRINTF_VARARGS * 8 ||
-	    (data_len && !data))
+	if (data_len & 7 || data_len > MAX_BPRINTF_VARARGS * 8 ||
+	    (data_len && !args))
 		return -EINVAL;
 	num_args = data_len / 8;
 
-	err = bpf_bprintf_prepare(fmt, fmt_size, data, &bin_args, num_args);
+	err = bpf_bprintf_prepare(fmt, fmt_size, args, num_args, &data);
 	if (err < 0)
 		return err;
 
-	seq_bprintf(m, fmt, bin_args);
+	seq_bprintf(m, fmt, data.bin_args);
 
-	bpf_bprintf_cleanup();
+	bpf_bprintf_cleanup(&data);
 
 	return seq_has_overflowed(m) ? -EOVERFLOW : 0;
 }
@@ -446,9 +443,9 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_BTF_ID,
 	.arg1_btf_id	= &btf_seq_file_ids[0],
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
-	.arg4_type      = ARG_PTR_TO_MEM_OR_NULL,
+	.arg4_type      = ARG_PTR_TO_MEM | PTR_MAYBE_NULL | MEM_RDONLY,
 	.arg5_type      = ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -463,7 +460,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_BTF_ID,
 	.arg1_btf_id	= &btf_seq_file_ids[0],
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -487,7 +484,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_BTF_ID,
 	.arg1_btf_id	= &btf_seq_file_ids[0],
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE_OR_ZERO,
 	.arg4_type	= ARG_ANYTHING,
 };
@@ -648,7 +645,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -662,7 +659,6 @@
 u64 bpf_event_output(struct bpf_map *map, u64 flags, void *meta, u64 meta_size,
 		     void *ctx, u64 ctx_size, bpf_ctx_copy_t ctx_copy)
 {
-	int nest_level = this_cpu_inc_return(bpf_event_output_nest_level);
 	struct perf_raw_frag frag = {
 		.copy		= ctx_copy,
 		.size		= ctx_size,
@@ -679,8 +675,12 @@
 	};
 	struct perf_sample_data *sd;
 	struct pt_regs *regs;
+	int nest_level;
 	u64 ret;
 
+	preempt_disable();
+	nest_level = this_cpu_inc_return(bpf_event_output_nest_level);
+
 	if (WARN_ON_ONCE(nest_level > ARRAY_SIZE(bpf_misc_sds.sds))) {
 		ret = -EBUSY;
 		goto out;
@@ -695,6 +695,7 @@
 	ret = __bpf_perf_event_output(regs, map, flags, sd);
 out:
 	this_cpu_dec(bpf_event_output_nest_level);
+	preempt_enable();
 	return ret;
 }
 
@@ -776,6 +777,7 @@
 
 	work = container_of(entry, struct send_signal_irq_work, irq_work);
 	group_send_sig_info(work->sig, SEND_SIG_PRIV, work->task, work->type);
+	put_task_struct(work->task);
 }
 
 static int bpf_send_signal_common(u32 sig, enum pid_type type)
@@ -793,8 +795,11 @@
 		return -EPERM;
 	if (unlikely(!nmi_uaccess_okay()))
 		return -EPERM;
+	/* Task should not be pid=1 to avoid kernel panic. */
+	if (unlikely(is_global_init(current)))
+		return -EPERM;
 
-	if (irqs_disabled()) {
+	if (preempt_count() != 0 || irqs_disabled()) {
 		/* Do an early check on signal validity. Otherwise,
 		 * the error is lost in deferred irq_work.
 		 */
@@ -809,7 +814,7 @@
 		 * to the irq_work. The current task may change when queued
 		 * irq works get executed.
 		 */
-		work->task = current;
+		work->task = get_task_struct(current);
 		work->sig = sig;
 		work->type = type;
 		irq_work_queue(&work->irq_work);
@@ -845,13 +850,23 @@
 
 BPF_CALL_3(bpf_d_path, struct path *, path, char *, buf, u32, sz)
 {
+	struct path copy;
 	long len;
 	char *p;
 
 	if (!sz)
 		return 0;
 
-	p = d_path(path, buf, sz);
+	/*
+	 * The path pointer is verified as trusted and safe to use,
+	 * but let's double check it's valid anyway to workaround
+	 * potentially broken verifier.
+	 */
+	len = copy_from_kernel_nofault(&copy, path, sizeof(*path));
+	if (len < 0)
+		return len;
+
+	p = d_path(&copy, buf, sz);
 	if (IS_ERR(p)) {
 		len = PTR_ERR(p);
 	} else {
@@ -958,7 +973,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_MEM,
 	.arg2_type	= ARG_CONST_SIZE,
-	.arg3_type	= ARG_PTR_TO_MEM,
+	.arg3_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE,
 	.arg5_type	= ARG_ANYTHING,
 };
@@ -1037,8 +1052,6 @@
 		return &bpf_ktime_get_ns_proto;
 	case BPF_FUNC_ktime_get_boot_ns:
 		return &bpf_ktime_get_boot_ns_proto;
-	case BPF_FUNC_ktime_get_coarse_ns:
-		return &bpf_ktime_get_coarse_ns_proto;
 	case BPF_FUNC_tail_call:
 		return &bpf_tail_call_proto;
 	case BPF_FUNC_get_current_pid_tgid:
@@ -1209,7 +1222,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -1324,9 +1337,6 @@
 BPF_CALL_4(bpf_read_branch_records, struct bpf_perf_event_data_kern *, ctx,
 	   void *, buf, u32, size, u64, flags)
 {
-#ifndef CONFIG_X86
-	return -ENOENT;
-#else
 	static const u32 br_entry_size = sizeof(struct perf_branch_entry);
 	struct perf_branch_stack *br_stack = ctx->data->br_stack;
 	u32 to_copy;
@@ -1335,7 +1345,7 @@
 		return -EINVAL;
 
 	if (unlikely(!br_stack))
-		return -EINVAL;
+		return -ENOENT;
 
 	if (flags & BPF_F_GET_BRANCH_RECORDS_SIZE)
 		return br_stack->nr * br_entry_size;
@@ -1347,7 +1357,6 @@
 	memcpy(buf, br_stack->entries, to_copy);
 
 	return to_copy;
-#endif
 }
 
 static const struct bpf_func_proto bpf_read_branch_records_proto = {
@@ -1435,7 +1444,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -1489,7 +1498,7 @@
 	.gpl_only	= true,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE_OR_ZERO,
 	.arg4_type	= ARG_ANYTHING,
 };
@@ -1781,8 +1790,6 @@
 
 	old_array = bpf_event_rcu_dereference(event->tp_event->prog_array);
 	ret = bpf_prog_array_copy(old_array, event->prog, NULL, 0, &new_array);
-	if (ret == -ENOENT)
-		goto unlock;
 	if (ret < 0) {
 		bpf_prog_array_delete_safe(old_array, event->prog);
 	} else {
@@ -1984,7 +1991,7 @@
 #ifdef CONFIG_UPROBE_EVENTS
 		if (flags & TRACE_EVENT_FL_UPROBE)
 			err = bpf_get_uprobe_info(event, fd_type, buf,
-						  probe_offset,
+						  probe_offset, probe_addr,
 						  event->attr.type == PERF_TYPE_TRACEPOINT);
 #endif
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/ftrace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/ftrace.c
@@ -510,6 +510,7 @@
 	static struct trace_seq s;
 	unsigned long long avg;
 	unsigned long long stddev;
+	unsigned long long stddev_denom;
 #endif
 	mutex_lock(&ftrace_profile_lock);
 
@@ -531,23 +532,19 @@
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 	seq_puts(m, "    ");
 
-	/* Sample standard deviation (s^2) */
-	if (rec->counter <= 1)
-		stddev = 0;
-	else {
-		/*
-		 * Apply Welford's method:
-		 * s^2 = 1 / (n * (n-1)) * (n * \Sum (x_i)^2 - (\Sum x_i)^2)
-		 */
+	/*
+	 * Variance formula:
+	 * s^2 = 1 / (n * (n-1)) * (n * \Sum (x_i)^2 - (\Sum x_i)^2)
+	 * Maybe Welford's method is better here?
+	 * Divide only by 1000 for ns^2 -> us^2 conversion.
+	 * trace_print_graph_duration will divide by 1000 again.
+	 */
+	stddev = 0;
+	stddev_denom = rec->counter * (rec->counter - 1) * 1000;
+	if (stddev_denom) {
 		stddev = rec->counter * rec->time_squared -
 			 rec->time * rec->time;
-
-		/*
-		 * Divide only 1000 for ns^2 -> us^2 conversion.
-		 * trace_print_graph_duration will divide 1000 again.
-		 */
-		stddev = div64_ul(stddev,
-				  rec->counter * (rec->counter - 1) * 1000);
+		stddev = div64_ul(stddev, stddev_denom);
 	}
 
 	trace_seq_init(&s);
@@ -988,8 +985,9 @@
 		}
 	}
 
-	entry = tracefs_create_file("function_profile_enabled", 0644,
-				    d_tracer, NULL, &ftrace_profile_fops);
+	entry = tracefs_create_file("function_profile_enabled",
+				    TRACE_MODE_WRITE, d_tracer, NULL,
+				    &ftrace_profile_fops);
 	if (!entry)
 		pr_warn("Could not create tracefs 'function_profile_enabled' entry\n");
 }
@@ -1294,6 +1292,7 @@
 	if (!ftrace_mod)
 		return -ENOMEM;
 
+	INIT_LIST_HEAD(&ftrace_mod->list);
 	ftrace_mod->func = kstrdup(func, GFP_KERNEL);
 	ftrace_mod->module = kstrdup(module, GFP_KERNEL);
 	ftrace_mod->enable = enable;
@@ -1536,7 +1535,8 @@
 	key.flags = end;	/* overload flags, as it is unsigned long */
 
 	for (pg = ftrace_pages_start; pg; pg = pg->next) {
-		if (end < pg->records[0].ip ||
+		if (pg->index == 0 ||
+		    end < pg->records[0].ip ||
 		    start >= (pg->records[pg->index - 1].ip + MCOUNT_INSN_SIZE))
 			continue;
 		rec = bsearch(&key, pg->records, pg->index,
@@ -1563,26 +1563,43 @@
 unsigned long ftrace_location_range(unsigned long start, unsigned long end)
 {
 	struct dyn_ftrace *rec;
+	unsigned long ip = 0;
 
+	rcu_read_lock();
 	rec = lookup_rec(start, end);
 	if (rec)
-		return rec->ip;
+		ip = rec->ip;
+	rcu_read_unlock();
 
-	return 0;
+	return ip;
 }
 
 /**
- * ftrace_location - return true if the ip giving is a traced location
+ * ftrace_location - return the ftrace location
  * @ip: the instruction pointer to check
  *
- * Returns rec->ip if @ip given is a pointer to a ftrace location.
- * That is, the instruction that is either a NOP or call to
- * the function tracer. It checks the ftrace internal tables to
- * determine if the address belongs or not.
+ * If @ip matches the ftrace location, return @ip.
+ * If @ip matches sym+0, return sym's ftrace location.
+ * Otherwise, return 0.
  */
 unsigned long ftrace_location(unsigned long ip)
 {
-	return ftrace_location_range(ip, ip);
+	unsigned long loc;
+	unsigned long offset;
+	unsigned long size;
+
+	loc = ftrace_location_range(ip, ip);
+	if (!loc) {
+		if (!kallsyms_lookup_size_offset(ip, &size, &offset))
+			goto out;
+
+		/* map sym+0 to __fentry__ */
+		if (!offset)
+			loc = ftrace_location_range(ip, ip + size - 1);
+	}
+
+out:
+	return loc;
 }
 
 /**
@@ -2900,6 +2917,16 @@
 
 	ftrace_startup_enable(command);
 
+	/*
+	 * If ftrace is in an undefined state, we just remove ops from list
+	 * to prevent the NULL pointer, instead of totally rolling it back and
+	 * free trampoline, because those actions could cause further damage.
+	 */
+	if (unlikely(ftrace_disabled)) {
+		__unregister_ftrace_function(ops);
+		return -ENODEV;
+	}
+
 	ops->flags &= ~FTRACE_OPS_FL_ADDING;
 
 	return 0;
@@ -2937,18 +2964,8 @@
 		command |= FTRACE_UPDATE_TRACE_FUNC;
 	}
 
-	if (!command || !ftrace_enabled) {
-		/*
-		 * If these are dynamic or per_cpu ops, they still
-		 * need their data freed. Since, function tracing is
-		 * not currently active, we can just free them
-		 * without synchronizing all CPUs.
-		 */
-		if (ops->flags & FTRACE_OPS_FL_DYNAMIC)
-			goto free_ops;
-
-		return 0;
-	}
+	if (!command || !ftrace_enabled)
+		goto out;
 
 	/*
 	 * If the ops uses a trampoline, then it needs to be
@@ -2985,6 +3002,7 @@
 	removed_ops = NULL;
 	ops->flags &= ~FTRACE_OPS_FL_REMOVING;
 
+out:
 	/*
 	 * Dynamic ops may be freed, we must make sure that all
 	 * callers are done before leaving this function.
@@ -3012,7 +3030,6 @@
 		if (IS_ENABLED(CONFIG_PREEMPTION))
 			synchronize_rcu_tasks();
 
- free_ops:
 		ftrace_trampoline_free(ops);
 	}
 
@@ -3173,7 +3190,7 @@
 		/* if we can't allocate this size, try something smaller */
 		if (!order)
 			return -ENOMEM;
-		order >>= 1;
+		order--;
 		goto again;
 	}
 
@@ -3189,6 +3206,22 @@
 	return cnt;
 }
 
+static void ftrace_free_pages(struct ftrace_page *pages)
+{
+	struct ftrace_page *pg = pages;
+
+	while (pg) {
+		if (pg->records) {
+			free_pages((unsigned long)pg->records, pg->order);
+			ftrace_number_of_pages -= 1 << pg->order;
+		}
+		pages = pg->next;
+		kfree(pg);
+		pg = pages;
+		ftrace_number_of_groups--;
+	}
+}
+
 static struct ftrace_page *
 ftrace_allocate_pages(unsigned long num_to_init)
 {
@@ -3227,17 +3260,7 @@
 	return start_pg;
 
  free_pages:
-	pg = start_pg;
-	while (pg) {
-		if (pg->records) {
-			free_pages((unsigned long)pg->records, pg->order);
-			ftrace_number_of_pages -= 1 << pg->order;
-		}
-		start_pg = pg->next;
-		kfree(pg);
-		pg = start_pg;
-		ftrace_number_of_groups--;
-	}
+	ftrace_free_pages(start_pg);
 	pr_info("ftrace: FAILED to allocate memory for functions\n");
 	return NULL;
 }
@@ -4279,6 +4302,9 @@
 	char *func;
 	int ret;
 
+	if (!tr)
+		return -ENODEV;
+
 	/* match_records() modifies func, and we need the original */
 	func = kstrdup(func_orig, GFP_KERNEL);
 	if (!func)
@@ -4419,7 +4445,7 @@
  * @ip: The instruction pointer address to remove the data from
  *
  * Returns the data if it is found, otherwise NULL.
- * Note, if the data pointer is used as the data itself, (see 
+ * Note, if the data pointer is used as the data itself, (see
  * ftrace_func_mapper_find_ip(), then the return value may be meaningless,
  * if the data pointer was set to zero.
  */
@@ -4933,7 +4959,8 @@
 {
 	struct ftrace_func_entry *entry;
 
-	if (!ftrace_location(ip))
+	ip = ftrace_location(ip);
+	if (!ip)
 		return -EINVAL;
 
 	if (remove) {
@@ -5081,11 +5108,16 @@
 	struct ftrace_func_entry *entry;
 	struct ftrace_hash *free_hash = NULL;
 	struct dyn_ftrace *rec;
-	int ret = -EBUSY;
+	int ret = -ENODEV;
 
 	mutex_lock(&direct_mutex);
 
+	ip = ftrace_location(ip);
+	if (!ip)
+		goto out_unlock;
+
 	/* See if there's a direct function at @ip already */
+	ret = -EBUSY;
 	if (ftrace_find_rec_direct(ip))
 		goto out_unlock;
 
@@ -5145,8 +5177,6 @@
 	__add_hash_entry(direct_functions, entry);
 
 	ret = ftrace_set_filter_ip(&direct_ops, ip, 0, 0);
-	if (ret)
-		remove_hash_entry(direct_functions, entry);
 
 	if (!ret && !(direct_ops.flags & FTRACE_OPS_FL_ENABLED)) {
 		ret = register_ftrace_function(&direct_ops);
@@ -5155,6 +5185,7 @@
 	}
 
 	if (ret) {
+		remove_hash_entry(direct_functions, entry);
 		kfree(entry);
 		if (!direct->count) {
 			list_del_rcu(&direct->next);
@@ -5215,6 +5246,10 @@
 
 	mutex_lock(&direct_mutex);
 
+	ip = ftrace_location(ip);
+	if (!ip)
+		goto out_unlock;
+
 	entry = find_direct_entry(&ip, NULL);
 	if (!entry)
 		goto out_unlock;
@@ -5346,6 +5381,11 @@
 	mutex_lock(&direct_mutex);
 
 	mutex_lock(&ftrace_lock);
+
+	ip = ftrace_location(ip);
+	if (!ip)
+		goto out_unlock;
+
 	entry = find_direct_entry(&ip, &rec);
 	if (!entry)
 		goto out_unlock;
@@ -5381,12 +5421,15 @@
 		ret = 0;
 	}
 
-	if (unlikely(ret && new_direct)) {
-		direct->count++;
-		list_del_rcu(&new_direct->next);
-		synchronize_rcu_tasks();
-		kfree(new_direct);
-		ftrace_direct_func_count--;
+	if (ret) {
+		direct->addr = old_addr;
+		if (unlikely(new_direct)) {
+			direct->count++;
+			list_del_rcu(&new_direct->next);
+			synchronize_rcu_tasks();
+			kfree(new_direct);
+			ftrace_direct_func_count--;
+		}
 	}
 
  out_unlock:
@@ -5644,8 +5687,12 @@
 
 		if (filter_hash) {
 			orig_hash = &iter->ops->func_hash->filter_hash;
-			if (iter->tr && !list_empty(&iter->tr->mod_trace))
-				iter->hash->flags |= FTRACE_HASH_FL_MOD;
+			if (iter->tr) {
+				if (list_empty(&iter->tr->mod_trace))
+					iter->hash->flags &= ~FTRACE_HASH_FL_MOD;
+				else
+					iter->hash->flags |= FTRACE_HASH_FL_MOD;
+			}
 		} else
 			orig_hash = &iter->ops->func_hash->notrace_hash;
 
@@ -6109,10 +6156,10 @@
 				struct dentry *parent)
 {
 
-	trace_create_file("set_ftrace_filter", 0644, parent,
+	trace_create_file("set_ftrace_filter", TRACE_MODE_WRITE, parent,
 			  ops, &ftrace_filter_fops);
 
-	trace_create_file("set_ftrace_notrace", 0644, parent,
+	trace_create_file("set_ftrace_notrace", TRACE_MODE_WRITE, parent,
 			  ops, &ftrace_notrace_fops);
 }
 
@@ -6139,19 +6186,19 @@
 static __init int ftrace_init_dyn_tracefs(struct dentry *d_tracer)
 {
 
-	trace_create_file("available_filter_functions", 0444,
+	trace_create_file("available_filter_functions", TRACE_MODE_READ,
 			d_tracer, NULL, &ftrace_avail_fops);
 
-	trace_create_file("enabled_functions", 0444,
+	trace_create_file("enabled_functions", TRACE_MODE_READ,
 			d_tracer, NULL, &ftrace_enabled_fops);
 
 	ftrace_create_filter_files(&global_ops, d_tracer);
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
-	trace_create_file("set_graph_function", 0644, d_tracer,
+	trace_create_file("set_graph_function", TRACE_MODE_WRITE, d_tracer,
 				    NULL,
 				    &ftrace_graph_fops);
-	trace_create_file("set_graph_notrace", 0644, d_tracer,
+	trace_create_file("set_graph_notrace", TRACE_MODE_WRITE, d_tracer,
 				    NULL,
 				    &ftrace_graph_notrace_fops);
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */
@@ -6175,9 +6222,11 @@
 			       unsigned long *start,
 			       unsigned long *end)
 {
+	struct ftrace_page *pg_unuse = NULL;
 	struct ftrace_page *start_pg;
 	struct ftrace_page *pg;
 	struct dyn_ftrace *rec;
+	unsigned long skipped = 0;
 	unsigned long count;
 	unsigned long *p;
 	unsigned long addr;
@@ -6231,8 +6280,10 @@
 		 * object files to satisfy alignments.
 		 * Skip any NULL pointers.
 		 */
-		if (!addr)
+		if (!addr) {
+			skipped++;
 			continue;
+		}
 
 		end_offset = (pg->index+1) * sizeof(pg->records[0]);
 		if (end_offset > PAGE_SIZE << pg->order) {
@@ -6246,8 +6297,10 @@
 		rec->ip = addr;
 	}
 
-	/* We should have used all pages */
-	WARN_ON(pg->next);
+	if (pg->next) {
+		pg_unuse = pg->next;
+		pg->next = NULL;
+	}
 
 	/* Assign the last page to ftrace_pages */
 	ftrace_pages = pg;
@@ -6269,6 +6322,13 @@
  out:
 	mutex_unlock(&ftrace_lock);
 
+	/* We should have used all pages unless we skipped some */
+	if (pg_unuse) {
+		WARN_ON(!skipped);
+		/* Need to synchronize with ftrace_location_range() */
+		synchronize_rcu();
+		ftrace_free_pages(pg_unuse);
+	}
 	return ret;
 }
 
@@ -6449,6 +6509,9 @@
  out_unlock:
 	mutex_unlock(&ftrace_lock);
 
+	/* Need to synchronize with ftrace_location_range() */
+	if (tmp_page)
+		synchronize_rcu();
 	for (pg = tmp_page; pg; pg = tmp_page) {
 
 		/* Needs to be called outside of ftrace_lock */
@@ -6771,6 +6834,7 @@
 	unsigned long start = (unsigned long)(start_ptr);
 	unsigned long end = (unsigned long)(end_ptr);
 	struct ftrace_page **last_pg = &ftrace_pages_start;
+	struct ftrace_page *tmp_page = NULL;
 	struct ftrace_page *pg;
 	struct dyn_ftrace *rec;
 	struct dyn_ftrace key;
@@ -6814,12 +6878,8 @@
 		ftrace_update_tot_cnt--;
 		if (!pg->index) {
 			*last_pg = pg->next;
-			if (pg->records) {
-				free_pages((unsigned long)pg->records, pg->order);
-				ftrace_number_of_pages -= 1 << pg->order;
-			}
-			ftrace_number_of_groups--;
-			kfree(pg);
+			pg->next = tmp_page;
+			tmp_page = pg;
 			pg = container_of(last_pg, struct ftrace_page, next);
 			if (!(*last_pg))
 				ftrace_pages = pg;
@@ -6836,6 +6896,11 @@
 		clear_func_from_hashes(func);
 		kfree(func);
 	}
+	/* Need to synchronize with ftrace_location_range() */
+	if (tmp_page) {
+		synchronize_rcu();
+		ftrace_free_pages(tmp_page);
+	}
 }
 
 void __init ftrace_free_init_mem(void)
@@ -6866,7 +6931,7 @@
 	}
 
 	pr_info("ftrace: allocating %ld entries in %ld pages\n",
-		count, count / ENTRIES_PER_PAGE + 1);
+		count, DIV_ROUND_UP(count, ENTRIES_PER_PAGE));
 
 	last_ftrace_enabled = ftrace_enabled = 1;
 
@@ -7184,10 +7249,10 @@
 	synchronize_rcu();
 
 	if ((type & TRACE_PIDS) && pid_list)
-		trace_free_pid_list(pid_list);
+		trace_pid_list_free(pid_list);
 
 	if ((type & TRACE_NO_PIDS) && no_pid_list)
-		trace_free_pid_list(no_pid_list);
+		trace_pid_list_free(no_pid_list);
 }
 
 void ftrace_clear_pids(struct trace_array *tr)
@@ -7428,7 +7493,7 @@
 
 	if (filtered_pids) {
 		synchronize_rcu();
-		trace_free_pid_list(filtered_pids);
+		trace_pid_list_free(filtered_pids);
 	} else if (pid_list && !other_pids) {
 		/* Register a probe to set whether to ignore the tracing of a task */
 		register_trace_sched_switch(ftrace_filter_pid_sched_switch_probe, tr);
@@ -7494,10 +7559,10 @@
 
 void ftrace_init_tracefs(struct trace_array *tr, struct dentry *d_tracer)
 {
-	trace_create_file("set_ftrace_pid", 0644, d_tracer,
+	trace_create_file("set_ftrace_pid", TRACE_MODE_WRITE, d_tracer,
 			    tr, &ftrace_pid_fops);
-	trace_create_file("set_ftrace_notrace_pid", 0644, d_tracer,
-			    tr, &ftrace_no_pid_fops);
+	trace_create_file("set_ftrace_notrace_pid", TRACE_MODE_WRITE,
+			  d_tracer, tr, &ftrace_no_pid_fops);
 }
 
 void __init ftrace_init_tracefs_toplevel(struct trace_array *tr,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/kprobe_event_gen_test.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/kprobe_event_gen_test.c
@@ -35,6 +35,49 @@
 static struct trace_event_file *gen_kprobe_test;
 static struct trace_event_file *gen_kretprobe_test;
 
+#define KPROBE_GEN_TEST_FUNC	"do_sys_open"
+
+/* X86 */
+#if defined(CONFIG_X86_64) || defined(CONFIG_X86_32)
+#define KPROBE_GEN_TEST_ARG0	"dfd=%ax"
+#define KPROBE_GEN_TEST_ARG1	"filename=%dx"
+#define KPROBE_GEN_TEST_ARG2	"flags=%cx"
+#define KPROBE_GEN_TEST_ARG3	"mode=+4($stack)"
+
+/* ARM64 */
+#elif defined(CONFIG_ARM64)
+#define KPROBE_GEN_TEST_ARG0	"dfd=%x0"
+#define KPROBE_GEN_TEST_ARG1	"filename=%x1"
+#define KPROBE_GEN_TEST_ARG2	"flags=%x2"
+#define KPROBE_GEN_TEST_ARG3	"mode=%x3"
+
+/* ARM */
+#elif defined(CONFIG_ARM)
+#define KPROBE_GEN_TEST_ARG0	"dfd=%r0"
+#define KPROBE_GEN_TEST_ARG1	"filename=%r1"
+#define KPROBE_GEN_TEST_ARG2	"flags=%r2"
+#define KPROBE_GEN_TEST_ARG3	"mode=%r3"
+
+/* RISCV */
+#elif defined(CONFIG_RISCV)
+#define KPROBE_GEN_TEST_ARG0	"dfd=%a0"
+#define KPROBE_GEN_TEST_ARG1	"filename=%a1"
+#define KPROBE_GEN_TEST_ARG2	"flags=%a2"
+#define KPROBE_GEN_TEST_ARG3	"mode=%a3"
+
+/* others */
+#else
+#define KPROBE_GEN_TEST_ARG0	NULL
+#define KPROBE_GEN_TEST_ARG1	NULL
+#define KPROBE_GEN_TEST_ARG2	NULL
+#define KPROBE_GEN_TEST_ARG3	NULL
+#endif
+
+static bool trace_event_file_is_valid(struct trace_event_file *input)
+{
+	return input && !IS_ERR(input);
+}
+
 /*
  * Test to make sure we can create a kprobe event, then add more
  * fields.
@@ -58,23 +101,23 @@
 	 * fields.
 	 */
 	ret = kprobe_event_gen_cmd_start(&cmd, "gen_kprobe_test",
-					 "do_sys_open",
-					 "dfd=%ax", "filename=%dx");
+					 KPROBE_GEN_TEST_FUNC,
+					 KPROBE_GEN_TEST_ARG0, KPROBE_GEN_TEST_ARG1);
 	if (ret)
-		goto free;
+		goto out;
 
 	/* Use kprobe_event_add_fields to add the rest of the fields */
 
-	ret = kprobe_event_add_fields(&cmd, "flags=%cx", "mode=+4($stack)");
+	ret = kprobe_event_add_fields(&cmd, KPROBE_GEN_TEST_ARG2, KPROBE_GEN_TEST_ARG3);
 	if (ret)
-		goto free;
+		goto out;
 
 	/*
 	 * This actually creates the event.
 	 */
 	ret = kprobe_event_gen_cmd_end(&cmd);
 	if (ret)
-		goto free;
+		goto out;
 
 	/*
 	 * Now get the gen_kprobe_test event file.  We need to prevent
@@ -97,13 +140,13 @@
 		goto delete;
 	}
  out:
+	kfree(buf);
 	return ret;
  delete:
+	if (trace_event_file_is_valid(gen_kprobe_test))
+		gen_kprobe_test = NULL;
 	/* We got an error after creating the event, delete it */
-	ret = kprobe_event_delete("gen_kprobe_test");
- free:
-	kfree(buf);
-
+	kprobe_event_delete("gen_kprobe_test");
 	goto out;
 }
 
@@ -128,17 +171,17 @@
 	 * Define the kretprobe event.
 	 */
 	ret = kretprobe_event_gen_cmd_start(&cmd, "gen_kretprobe_test",
-					    "do_sys_open",
+					    KPROBE_GEN_TEST_FUNC,
 					    "$retval");
 	if (ret)
-		goto free;
+		goto out;
 
 	/*
 	 * This actually creates the event.
 	 */
 	ret = kretprobe_event_gen_cmd_end(&cmd);
 	if (ret)
-		goto free;
+		goto out;
 
 	/*
 	 * Now get the gen_kretprobe_test event file.  We need to
@@ -162,13 +205,13 @@
 		goto delete;
 	}
  out:
+	kfree(buf);
 	return ret;
  delete:
+	if (trace_event_file_is_valid(gen_kretprobe_test))
+		gen_kretprobe_test = NULL;
 	/* We got an error after creating the event, delete it */
-	ret = kprobe_event_delete("gen_kretprobe_test");
- free:
-	kfree(buf);
-
+	kprobe_event_delete("gen_kretprobe_test");
 	goto out;
 }
 
@@ -182,10 +225,12 @@
 
 	ret = test_gen_kretprobe_cmd();
 	if (ret) {
-		WARN_ON(trace_array_set_clr_event(gen_kretprobe_test->tr,
-						  "kprobes",
-						  "gen_kretprobe_test", false));
-		trace_put_event_file(gen_kretprobe_test);
+		if (trace_event_file_is_valid(gen_kretprobe_test)) {
+			WARN_ON(trace_array_set_clr_event(gen_kretprobe_test->tr,
+							  "kprobes",
+							  "gen_kretprobe_test", false));
+			trace_put_event_file(gen_kretprobe_test);
+		}
 		WARN_ON(kprobe_event_delete("gen_kretprobe_test"));
 	}
 
@@ -194,24 +239,30 @@
 
 static void __exit kprobe_event_gen_test_exit(void)
 {
-	/* Disable the event or you can't remove it */
-	WARN_ON(trace_array_set_clr_event(gen_kprobe_test->tr,
-					  "kprobes",
-					  "gen_kprobe_test", false));
+	if (trace_event_file_is_valid(gen_kprobe_test)) {
+		/* Disable the event or you can't remove it */
+		WARN_ON(trace_array_set_clr_event(gen_kprobe_test->tr,
+						  "kprobes",
+						  "gen_kprobe_test", false));
+
+		/* Now give the file and instance back */
+		trace_put_event_file(gen_kprobe_test);
+	}
 
-	/* Now give the file and instance back */
-	trace_put_event_file(gen_kprobe_test);
 
 	/* Now unregister and free the event */
 	WARN_ON(kprobe_event_delete("gen_kprobe_test"));
 
-	/* Disable the event or you can't remove it */
-	WARN_ON(trace_array_set_clr_event(gen_kprobe_test->tr,
-					  "kprobes",
-					  "gen_kretprobe_test", false));
+	if (trace_event_file_is_valid(gen_kretprobe_test)) {
+		/* Disable the event or you can't remove it */
+		WARN_ON(trace_array_set_clr_event(gen_kretprobe_test->tr,
+						  "kprobes",
+						  "gen_kretprobe_test", false));
+
+		/* Now give the file and instance back */
+		trace_put_event_file(gen_kretprobe_test);
+	}
 
-	/* Now give the file and instance back */
-	trace_put_event_file(gen_kretprobe_test);
 
 	/* Now unregister and free the event */
 	WARN_ON(kprobe_event_delete("gen_kretprobe_test"));
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/pid_list.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/pid_list.c
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 VMware Inc, Steven Rostedt <rostedt@goodmis.org>
+ */
+#include <linux/vmalloc.h>
+#include <linux/slab.h>
+#include "trace.h"
+
+/**
+ * trace_pid_list_is_set - test if the pid is set in the list
+ * @pid_list: The pid list to test
+ * @pid: The pid to to see if set in the list.
+ *
+ * Tests if @pid is is set in the @pid_list. This is usually called
+ * from the scheduler when a task is scheduled. Its pid is checked
+ * if it should be traced or not.
+ *
+ * Return true if the pid is in the list, false otherwise.
+ */
+bool trace_pid_list_is_set(struct trace_pid_list *pid_list, unsigned int pid)
+{
+	/*
+	 * If pid_max changed after filtered_pids was created, we
+	 * by default ignore all pids greater than the previous pid_max.
+	 */
+	if (pid >= pid_list->pid_max)
+		return false;
+
+	return test_bit(pid, pid_list->pids);
+}
+
+/**
+ * trace_pid_list_set - add a pid to the list
+ * @pid_list: The pid list to add the @pid to.
+ * @pid: The pid to add.
+ *
+ * Adds @pid to @pid_list. This is usually done explicitly by a user
+ * adding a task to be traced, or indirectly by the fork function
+ * when children should be traced and a task's pid is in the list.
+ *
+ * Return 0 on success, negative otherwise.
+ */
+int trace_pid_list_set(struct trace_pid_list *pid_list, unsigned int pid)
+{
+	/* Sorry, but we don't support pid_max changing after setting */
+	if (pid >= pid_list->pid_max)
+		return -EINVAL;
+
+	set_bit(pid, pid_list->pids);
+
+	return 0;
+}
+
+/**
+ * trace_pid_list_clear - remove a pid from the list
+ * @pid_list: The pid list to remove the @pid from.
+ * @pid: The pid to remove.
+ *
+ * Removes @pid from @pid_list. This is usually done explicitly by a user
+ * removing tasks from tracing, or indirectly by the exit function
+ * when a task that is set to be traced exits.
+ *
+ * Return 0 on success, negative otherwise.
+ */
+int trace_pid_list_clear(struct trace_pid_list *pid_list, unsigned int pid)
+{
+	/* Sorry, but we don't support pid_max changing after setting */
+	if (pid >= pid_list->pid_max)
+		return -EINVAL;
+
+	clear_bit(pid, pid_list->pids);
+
+	return 0;
+}
+
+/**
+ * trace_pid_list_next - return the next pid in the list
+ * @pid_list: The pid list to examine.
+ * @pid: The pid to start from
+ * @next: The pointer to place the pid that is set starting from @pid.
+ *
+ * Looks for the next consecutive pid that is in @pid_list starting
+ * at the pid specified by @pid. If one is set (including @pid), then
+ * that pid is placed into @next.
+ *
+ * Return 0 when a pid is found, -1 if there are no more pids included.
+ */
+int trace_pid_list_next(struct trace_pid_list *pid_list, unsigned int pid,
+			unsigned int *next)
+{
+	pid = find_next_bit(pid_list->pids, pid_list->pid_max, pid);
+
+	if (pid < pid_list->pid_max) {
+		*next = pid;
+		return 0;
+	}
+	return -1;
+}
+
+/**
+ * trace_pid_list_first - return the first pid in the list
+ * @pid_list: The pid list to examine.
+ * @pid: The pointer to place the pid first found pid that is set.
+ *
+ * Looks for the first pid that is set in @pid_list, and places it
+ * into @pid if found.
+ *
+ * Return 0 when a pid is found, -1 if there are no pids set.
+ */
+int trace_pid_list_first(struct trace_pid_list *pid_list, unsigned int *pid)
+{
+	unsigned int first;
+
+	first = find_first_bit(pid_list->pids, pid_list->pid_max);
+
+	if (first < pid_list->pid_max) {
+		*pid = first;
+		return 0;
+	}
+	return -1;
+}
+
+/**
+ * trace_pid_list_alloc - create a new pid_list
+ *
+ * Allocates a new pid_list to store pids into.
+ *
+ * Returns the pid_list on success, NULL otherwise.
+ */
+struct trace_pid_list *trace_pid_list_alloc(void)
+{
+	struct trace_pid_list *pid_list;
+
+	pid_list = kmalloc(sizeof(*pid_list), GFP_KERNEL);
+	if (!pid_list)
+		return NULL;
+
+	pid_list->pid_max = READ_ONCE(pid_max);
+
+	pid_list->pids = vzalloc((pid_list->pid_max + 7) >> 3);
+	if (!pid_list->pids) {
+		kfree(pid_list);
+		return NULL;
+	}
+	return pid_list;
+}
+
+/**
+ * trace_pid_list_free - Frees an allocated pid_list.
+ *
+ * Frees the memory for a pid_list that was allocated.
+ */
+void trace_pid_list_free(struct trace_pid_list *pid_list)
+{
+	if (!pid_list)
+		return;
+
+	vfree(pid_list->pids);
+	kfree(pid_list);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/pid_list.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/pid_list.h
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Do not include this file directly. */
+
+#ifndef _TRACE_INTERNAL_PID_LIST_H
+#define _TRACE_INTERNAL_PID_LIST_H
+
+struct trace_pid_list {
+	int			pid_max;
+	unsigned long		*pids;
+};
+
+#endif /* _TRACE_INTERNAL_PID_LIST_H */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/preemptirq_delay_test.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/preemptirq_delay_test.c
@@ -215,4 +215,5 @@
 
 module_init(preemptirq_delay_init)
 module_exit(preemptirq_delay_exit)
+MODULE_DESCRIPTION("Preempt / IRQ disable delay thread to test latency tracers");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/ring_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/ring_buffer.c
@@ -346,10 +346,11 @@
 	local_set(&bpage->commit, 0);
 }
 
-/*
- * Also stolen from mm/slob.c. Thanks to Mathieu Desnoyers for pointing
- * this issue out.
- */
+static __always_inline unsigned int rb_page_commit(struct buffer_page *bpage)
+{
+	return local_read(&bpage->page->commit);
+}
+
 static void free_buffer_page(struct buffer_page *bpage)
 {
 	free_page((unsigned long)bpage->page);
@@ -509,6 +510,7 @@
 	local_t				committing;
 	local_t				commits;
 	local_t				pages_touched;
+	local_t				pages_lost;
 	local_t				pages_read;
 	long				last_pages_touch;
 	size_t				shortest_full;
@@ -518,6 +520,8 @@
 	rb_time_t			before_stamp;
 	u64				event_stamp[MAX_NEST];
 	u64				read_stamp;
+	/* pages removed since last reset */
+	unsigned long			pages_removed;
 	/* ring buffer pages to update, > 0 to add, < 0 to remove */
 	long				nr_pages_to_update;
 	struct list_head		new_pages; /* new pages to add */
@@ -531,6 +535,7 @@
 	unsigned			flags;
 	int				cpus;
 	atomic_t			record_disabled;
+	atomic_t			resizing;
 	cpumask_var_t			cpumask;
 
 	struct lock_class_key		*reader_lock_key;
@@ -553,6 +558,7 @@
 	struct buffer_page		*head_page;
 	struct buffer_page		*cache_reader_page;
 	unsigned long			cache_read;
+	unsigned long			cache_pages_removed;
 	u64				read_stamp;
 	u64				page_stamp;
 	struct ring_buffer_event	*event;
@@ -684,42 +690,6 @@
 	return ret == expect;
 }
 
-static int rb_time_cmpxchg(rb_time_t *t, u64 expect, u64 set)
-{
-	unsigned long cnt, top, bottom;
-	unsigned long cnt2, top2, bottom2;
-	u64 val;
-
-	/* The cmpxchg always fails if it interrupted an update */
-	 if (!__rb_time_read(t, &val, &cnt2))
-		 return false;
-
-	 if (val != expect)
-		 return false;
-
-	 cnt = local_read(&t->cnt);
-	 if ((cnt & 3) != cnt2)
-		 return false;
-
-	 cnt2 = cnt + 1;
-
-	 rb_time_split(val, &top, &bottom);
-	 top = rb_time_val_cnt(top, cnt);
-	 bottom = rb_time_val_cnt(bottom, cnt);
-
-	 rb_time_split(set, &top2, &bottom2);
-	 top2 = rb_time_val_cnt(top2, cnt2);
-	 bottom2 = rb_time_val_cnt(bottom2, cnt2);
-
-	if (!rb_time_read_cmpxchg(&t->cnt, cnt, cnt2))
-		return false;
-	if (!rb_time_read_cmpxchg(&t->top, top, top2))
-		return false;
-	if (!rb_time_read_cmpxchg(&t->bottom, bottom, bottom2))
-		return false;
-	return true;
-}
-
 #else /* 64 bits */
 
 /* local64_t always succeeds */
@@ -733,13 +703,6 @@
 {
 	local64_set(&t->time, val);
 }
-
-static bool rb_time_cmpxchg(rb_time_t *t, u64 expect, u64 set)
-{
-	u64 val;
-	val = local64_cmpxchg(&t->time, expect, set);
-	return val == expect;
-}
 #endif
 
 /*
@@ -857,10 +820,18 @@
 size_t ring_buffer_nr_dirty_pages(struct trace_buffer *buffer, int cpu)
 {
 	size_t read;
+	size_t lost;
 	size_t cnt;
 
 	read = local_read(&buffer->buffers[cpu]->pages_read);
+	lost = local_read(&buffer->buffers[cpu]->pages_lost);
 	cnt = local_read(&buffer->buffers[cpu]->pages_touched);
+
+	if (WARN_ON_ONCE(cnt < lost))
+		return 0;
+
+	cnt -= lost;
+
 	/* The reader can read an empty page, but not more than that */
 	if (cnt < read) {
 		WARN_ON_ONCE(read > cnt + 1);
@@ -870,6 +841,26 @@
 	return cnt - read;
 }
 
+static __always_inline bool full_hit(struct trace_buffer *buffer, int cpu, int full)
+{
+	struct ring_buffer_per_cpu *cpu_buffer = buffer->buffers[cpu];
+	size_t nr_pages;
+	size_t dirty;
+
+	nr_pages = cpu_buffer->nr_pages;
+	if (!nr_pages || !full)
+		return true;
+
+	/*
+	 * Add one as dirty will never equal nr_pages, as the sub-buffer
+	 * that the writer is on is not counted as dirty.
+	 * This is needed if "buffer_percent" is set to 100.
+	 */
+	dirty = ring_buffer_nr_dirty_pages(buffer, cpu) + 1;
+
+	return (dirty * 100) >= (full * nr_pages);
+}
+
 /*
  * rb_wake_up_waiters - wake up tasks waiting for ring buffer input
  *
@@ -881,13 +872,149 @@
 	struct rb_irq_work *rbwork = container_of(work, struct rb_irq_work, work);
 
 	wake_up_all(&rbwork->waiters);
-	if (rbwork->wakeup_full) {
+	if (rbwork->full_waiters_pending || rbwork->wakeup_full) {
+		/* Only cpu_buffer sets the above flags */
+		struct ring_buffer_per_cpu *cpu_buffer =
+			container_of(rbwork, struct ring_buffer_per_cpu, irq_work);
+
+		/* Called from interrupt context */
+		raw_spin_lock(&cpu_buffer->reader_lock);
 		rbwork->wakeup_full = false;
+		rbwork->full_waiters_pending = false;
+
+		/* Waking up all waiters, they will reset the shortest full */
+		cpu_buffer->shortest_full = 0;
+		raw_spin_unlock(&cpu_buffer->reader_lock);
+
 		wake_up_all(&rbwork->full_waiters);
 	}
 }
 
 /**
+ * ring_buffer_wake_waiters - wake up any waiters on this ring buffer
+ * @buffer: The ring buffer to wake waiters on
+ *
+ * In the case of a file that represents a ring buffer is closing,
+ * it is prudent to wake up any waiters that are on this.
+ */
+void ring_buffer_wake_waiters(struct trace_buffer *buffer, int cpu)
+{
+	struct ring_buffer_per_cpu *cpu_buffer;
+	struct rb_irq_work *rbwork;
+
+	if (!buffer)
+		return;
+
+	if (cpu == RING_BUFFER_ALL_CPUS) {
+
+		/* Wake up individual ones too. One level recursion */
+		for_each_buffer_cpu(buffer, cpu)
+			ring_buffer_wake_waiters(buffer, cpu);
+
+		rbwork = &buffer->irq_work;
+	} else {
+		if (WARN_ON_ONCE(!buffer->buffers))
+			return;
+		if (WARN_ON_ONCE(cpu >= nr_cpu_ids))
+			return;
+
+		cpu_buffer = buffer->buffers[cpu];
+		/* The CPU buffer may not have been initialized yet */
+		if (!cpu_buffer)
+			return;
+		rbwork = &cpu_buffer->irq_work;
+	}
+
+	/* This can be called in any context */
+	irq_work_queue(&rbwork->work);
+}
+
+static bool rb_watermark_hit(struct trace_buffer *buffer, int cpu, int full)
+{
+	struct ring_buffer_per_cpu *cpu_buffer;
+	bool ret = false;
+
+	/* Reads of all CPUs always waits for any data */
+	if (cpu == RING_BUFFER_ALL_CPUS)
+		return !ring_buffer_empty(buffer);
+
+	cpu_buffer = buffer->buffers[cpu];
+
+	if (!ring_buffer_empty_cpu(buffer, cpu)) {
+		unsigned long flags;
+		bool pagebusy;
+
+		if (!full)
+			return true;
+
+		raw_spin_lock_irqsave(&cpu_buffer->reader_lock, flags);
+		pagebusy = cpu_buffer->reader_page == cpu_buffer->commit_page;
+		ret = !pagebusy && full_hit(buffer, cpu, full);
+
+		if (!ret && (!cpu_buffer->shortest_full ||
+			     cpu_buffer->shortest_full > full)) {
+		    cpu_buffer->shortest_full = full;
+		}
+		raw_spin_unlock_irqrestore(&cpu_buffer->reader_lock, flags);
+	}
+	return ret;
+}
+
+static inline bool
+rb_wait_cond(struct rb_irq_work *rbwork, struct trace_buffer *buffer,
+	     int cpu, int full, ring_buffer_cond_fn cond, void *data)
+{
+	if (rb_watermark_hit(buffer, cpu, full))
+		return true;
+
+	if (cond(data))
+		return true;
+
+	/*
+	 * The events can happen in critical sections where
+	 * checking a work queue can cause deadlocks.
+	 * After adding a task to the queue, this flag is set
+	 * only to notify events to try to wake up the queue
+	 * using irq_work.
+	 *
+	 * We don't clear it even if the buffer is no longer
+	 * empty. The flag only causes the next event to run
+	 * irq_work to do the work queue wake up. The worse
+	 * that can happen if we race with !trace_empty() is that
+	 * an event will cause an irq_work to try to wake up
+	 * an empty queue.
+	 *
+	 * There's no reason to protect this flag either, as
+	 * the work queue and irq_work logic will do the necessary
+	 * synchronization for the wake ups. The only thing
+	 * that is necessary is that the wake up happens after
+	 * a task has been queued. It's OK for spurious wake ups.
+	 */
+	if (full)
+		rbwork->full_waiters_pending = true;
+	else
+		rbwork->waiters_pending = true;
+
+	return false;
+}
+
+/*
+ * The default wait condition for ring_buffer_wait() is to just to exit the
+ * wait loop the first time it is woken up.
+ */
+static bool rb_wait_once(void *data)
+{
+	long *once = data;
+
+	/* wait_event() actually calls this twice before scheduling*/
+	if (*once > 1)
+		return true;
+
+	(*once)++;
+	return false;
+}
+
+/**
  * ring_buffer_wait - wait for input to the ring buffer
  * @buffer: buffer to wait on
  * @cpu: the cpu buffer to wait on
@@ -900,96 +1027,39 @@
 int ring_buffer_wait(struct trace_buffer *buffer, int cpu, int full)
 {
 	struct ring_buffer_per_cpu *cpu_buffer;
-	DEFINE_WAIT(wait);
-	struct rb_irq_work *work;
+	struct wait_queue_head *waitq;
+	ring_buffer_cond_fn cond;
+	struct rb_irq_work *rbwork;
+	void *data;
+	long once = 0;
 	int ret = 0;
 
+	cond = rb_wait_once;
+	data = &once;
+
 	/*
 	 * Depending on what the caller is waiting for, either any
 	 * data in any cpu buffer, or a specific buffer, put the
 	 * caller on the appropriate wait queue.
 	 */
 	if (cpu == RING_BUFFER_ALL_CPUS) {
-		work = &buffer->irq_work;
+		rbwork = &buffer->irq_work;
 		/* Full only makes sense on per cpu reads */
 		full = 0;
 	} else {
 		if (!cpumask_test_cpu(cpu, buffer->cpumask))
 			return -ENODEV;
 		cpu_buffer = buffer->buffers[cpu];
-		work = &cpu_buffer->irq_work;
-	}
-
-
-	while (true) {
-		if (full)
-			prepare_to_wait(&work->full_waiters, &wait, TASK_INTERRUPTIBLE);
-		else
-			prepare_to_wait(&work->waiters, &wait, TASK_INTERRUPTIBLE);
-
-		/*
-		 * The events can happen in critical sections where
-		 * checking a work queue can cause deadlocks.
-		 * After adding a task to the queue, this flag is set
-		 * only to notify events to try to wake up the queue
-		 * using irq_work.
-		 *
-		 * We don't clear it even if the buffer is no longer
-		 * empty. The flag only causes the next event to run
-		 * irq_work to do the work queue wake up. The worse
-		 * that can happen if we race with !trace_empty() is that
-		 * an event will cause an irq_work to try to wake up
-		 * an empty queue.
-		 *
-		 * There's no reason to protect this flag either, as
-		 * the work queue and irq_work logic will do the necessary
-		 * synchronization for the wake ups. The only thing
-		 * that is necessary is that the wake up happens after
-		 * a task has been queued. It's OK for spurious wake ups.
-		 */
-		if (full)
-			work->full_waiters_pending = true;
-		else
-			work->waiters_pending = true;
-
-		if (signal_pending(current)) {
-			ret = -EINTR;
-			break;
-		}
-
-		if (cpu == RING_BUFFER_ALL_CPUS && !ring_buffer_empty(buffer))
-			break;
-
-		if (cpu != RING_BUFFER_ALL_CPUS &&
-		    !ring_buffer_empty_cpu(buffer, cpu)) {
-			unsigned long flags;
-			bool pagebusy;
-			size_t nr_pages;
-			size_t dirty;
-
-			if (!full)
-				break;
-
-			raw_spin_lock_irqsave(&cpu_buffer->reader_lock, flags);
-			pagebusy = cpu_buffer->reader_page == cpu_buffer->commit_page;
-			nr_pages = cpu_buffer->nr_pages;
-			dirty = ring_buffer_nr_dirty_pages(buffer, cpu);
-			if (!cpu_buffer->shortest_full ||
-			    cpu_buffer->shortest_full < full)
-				cpu_buffer->shortest_full = full;
-			raw_spin_unlock_irqrestore(&cpu_buffer->reader_lock, flags);
-			if (!pagebusy &&
-			    (!nr_pages || (dirty * 100) > full * nr_pages))
-				break;
-		}
-
-		schedule();
+		rbwork = &cpu_buffer->irq_work;
 	}
 
 	if (full)
-		finish_wait(&work->full_waiters, &wait);
+		waitq = &rbwork->full_waiters;
 	else
-		finish_wait(&work->waiters, &wait);
+		waitq = &rbwork->waiters;
+
+	ret = wait_event_interruptible((*waitq),
+				rb_wait_cond(rbwork, buffer, cpu, full, cond, data));
 
 	return ret;
 }
@@ -1000,6 +1070,7 @@
  * @cpu: the cpu buffer to wait on
  * @filp: the file descriptor
  * @poll_table: The poll descriptor
+ * @full: wait until the percentage of pages are available, if @cpu != RING_BUFFER_ALL_CPUS
  *
  * If @cpu == RING_BUFFER_ALL_CPUS then the task will wake up as soon
  * as data is added to any of the @buffer's cpu buffers. Otherwise
@@ -1009,23 +1080,54 @@
  * zero otherwise.
  */
 __poll_t ring_buffer_poll_wait(struct trace_buffer *buffer, int cpu,
-			  struct file *filp, poll_table *poll_table)
+			  struct file *filp, poll_table *poll_table, int full)
 {
 	struct ring_buffer_per_cpu *cpu_buffer;
-	struct rb_irq_work *work;
+	struct rb_irq_work *rbwork;
 
-	if (cpu == RING_BUFFER_ALL_CPUS)
-		work = &buffer->irq_work;
-	else {
+	if (cpu == RING_BUFFER_ALL_CPUS) {
+		rbwork = &buffer->irq_work;
+		full = 0;
+	} else {
 		if (!cpumask_test_cpu(cpu, buffer->cpumask))
-			return -EINVAL;
+			return EPOLLERR;
 
 		cpu_buffer = buffer->buffers[cpu];
-		work = &cpu_buffer->irq_work;
+		rbwork = &cpu_buffer->irq_work;
 	}
 
-	poll_wait(filp, &work->waiters, poll_table);
-	work->waiters_pending = true;
+	if (full) {
+		unsigned long flags;
+
+		poll_wait(filp, &rbwork->full_waiters, poll_table);
+
+		raw_spin_lock_irqsave(&cpu_buffer->reader_lock, flags);
+		if (!cpu_buffer->shortest_full ||
+		    cpu_buffer->shortest_full > full)
+			cpu_buffer->shortest_full = full;
+		raw_spin_unlock_irqrestore(&cpu_buffer->reader_lock, flags);
+		if (full_hit(buffer, cpu, full))
+			return EPOLLIN | EPOLLRDNORM;
+		/*
+		 * Only allow full_waiters_pending update to be seen after
+		 * the shortest_full is set. If the writer sees the
+		 * full_waiters_pending flag set, it will compare the
+		 * amount in the ring buffer to shortest_full. If the amount
+		 * in the ring buffer is greater than the shortest_full
+		 * percent, it will call the irq_work handler to wake up
+		 * this list. The irq_handler will reset shortest_full
+		 * back to zero. That's done under the reader_lock, but
+		 * the below smp_mb() makes sure that the update to
+		 * full_waiters_pending doesn't leak up into the above.
+		 */
+		smp_mb();
+		rbwork->full_waiters_pending = true;
+		return 0;
+	}
+
+	poll_wait(filp, &rbwork->waiters, poll_table);
+	rbwork->waiters_pending = true;
+
 	/*
 	 * There's a tight race between setting the waiters_pending and
 	 * checking if the ring buffer is empty.  Once the waiters_pending bit
@@ -1407,7 +1509,6 @@
 	old_write = local_add_return(RB_WRITE_INTCNT, &next_page->write);
 	old_entries = local_add_return(RB_WRITE_INTCNT, &next_page->entries);
 
-	local_inc(&cpu_buffer->pages_touched);
 	/*
 	 * Just make sure we have seen our old_write and synchronize
 	 * with any interrupts that come in.
@@ -1444,8 +1545,9 @@
 		 */
 		local_set(&next_page->page->commit, 0);
 
-		/* Again, either we update tail_page or an interrupt does */
-		(void)cmpxchg(&cpu_buffer->tail_page, tail_page, next_page);
+		/* Either we update tail_page or an interrupt does */
+		if (try_cmpxchg(&cpu_buffer->tail_page, &tail_page, next_page))
+			local_inc(&cpu_buffer->pages_touched);
 	}
 }
 
@@ -1461,57 +1563,40 @@
 }
 
 /**
- * rb_check_list - make sure a pointer to a list has the last bits zero
- */
-static int rb_check_list(struct ring_buffer_per_cpu *cpu_buffer,
-			 struct list_head *list)
-{
-	if (RB_WARN_ON(cpu_buffer, rb_list_head(list->prev) != list->prev))
-		return 1;
-	if (RB_WARN_ON(cpu_buffer, rb_list_head(list->next) != list->next))
-		return 1;
-	return 0;
-}
-
-/**
  * rb_check_pages - integrity check of buffer pages
  * @cpu_buffer: CPU buffer with pages to test
  *
  * As a safety measure we check to make sure the data pages have not
  * been corrupted.
+ *
+ * Callers of this function need to guarantee that the list of pages doesn't get
+ * modified during the check. In particular, if it's possible that the function
+ * is invoked with concurrent readers which can swap in a new reader page then
+ * the caller should take cpu_buffer->reader_lock.
  */
 static int rb_check_pages(struct ring_buffer_per_cpu *cpu_buffer)
 {
-	struct list_head *head = cpu_buffer->pages;
-	struct buffer_page *bpage, *tmp;
+	struct list_head *head = rb_list_head(cpu_buffer->pages);
+	struct list_head *tmp;
 
-	/* Reset the head page if it exists */
-	if (cpu_buffer->head_page)
-		rb_set_head_page(cpu_buffer);
-
-	rb_head_page_deactivate(cpu_buffer);
-
-	if (RB_WARN_ON(cpu_buffer, head->next->prev != head))
-		return -1;
-	if (RB_WARN_ON(cpu_buffer, head->prev->next != head))
+	if (RB_WARN_ON(cpu_buffer,
+			rb_list_head(rb_list_head(head->next)->prev) != head))
 		return -1;
 
-	if (rb_check_list(cpu_buffer, head))
+	if (RB_WARN_ON(cpu_buffer,
+			rb_list_head(rb_list_head(head->prev)->next) != head))
 		return -1;
 
-	list_for_each_entry_safe(bpage, tmp, head, list) {
+	for (tmp = rb_list_head(head->next); tmp != head; tmp = rb_list_head(tmp->next)) {
 		if (RB_WARN_ON(cpu_buffer,
-			       bpage->list.next->prev != &bpage->list))
+				rb_list_head(rb_list_head(tmp->next)->prev) != tmp))
 			return -1;
+
 		if (RB_WARN_ON(cpu_buffer,
-			       bpage->list.prev->next != &bpage->list))
-			return -1;
-		if (rb_check_list(cpu_buffer, &bpage->list))
+				rb_list_head(rb_list_head(tmp->prev)->next) != tmp))
 			return -1;
 	}
 
-	rb_head_page_activate(cpu_buffer);
-
 	return 0;
 }
 
@@ -1680,11 +1765,13 @@
 	struct list_head *head = cpu_buffer->pages;
 	struct buffer_page *bpage, *tmp;
 
-	free_buffer_page(cpu_buffer->reader_page);
+	irq_work_sync(&cpu_buffer->irq_work.work);
 
-	rb_head_page_deactivate(cpu_buffer);
+	free_buffer_page(cpu_buffer->reader_page);
 
 	if (head) {
+		rb_head_page_deactivate(cpu_buffer);
+
 		list_for_each_entry_safe(bpage, tmp, head, list) {
 			list_del_init(&bpage->list);
 			free_buffer_page(bpage);
@@ -1693,6 +1780,8 @@
 		free_buffer_page(bpage);
 	}
 
+	free_page((unsigned long)cpu_buffer->free_page);
+
 	kfree(cpu_buffer);
 }
 
@@ -1786,6 +1875,8 @@
 
 	cpuhp_state_remove_instance(CPUHP_TRACE_RB_PREPARE, &buffer->node);
 
+	irq_work_sync(&buffer->irq_work.work);
+
 	for_each_buffer_cpu(buffer, cpu)
 		rb_free_cpu_buffer(buffer->buffers[cpu]);
 
@@ -1865,6 +1956,8 @@
 		to_remove = rb_list_head(to_remove)->next;
 		head_bit |= (unsigned long)to_remove & RB_PAGE_HEAD;
 	}
+	/* Read iterators need to reset themselves when some pages removed */
+	cpu_buffer->pages_removed += nr_removed;
 
 	next_page = rb_list_head(to_remove)->next;
 
@@ -1886,12 +1979,6 @@
 		cpu_buffer->head_page = list_entry(next_page,
 						struct buffer_page, list);
 
-	/*
-	 * change read pointer to make sure any read iterators reset
-	 * themselves
-	 */
-	cpu_buffer->read = 0;
-
 	/* pages are removed, resume tracing and then free the pages */
 	atomic_dec(&cpu_buffer->record_disabled);
 	raw_spin_unlock_irq(&cpu_buffer->reader_lock);
@@ -1919,7 +2006,8 @@
 			 * Increment overrun to account for the lost events.
 			 */
 			local_add(page_entries, &cpu_buffer->overrun);
-			local_sub(BUF_PAGE_SIZE, &cpu_buffer->entries_bytes);
+			local_sub(rb_page_commit(to_remove_page), &cpu_buffer->entries_bytes);
+			local_inc(&cpu_buffer->pages_lost);
 		}
 
 		/*
@@ -2071,7 +2159,7 @@
 
 	/* prevent another thread from changing buffer sizes */
 	mutex_lock(&buffer->mutex);
-
+	atomic_inc(&buffer->resizing);
 
 	if (cpu_id == RING_BUFFER_ALL_CPUS) {
 		/*
@@ -2109,6 +2197,8 @@
 				err = -ENOMEM;
 				goto out_err;
 			}
+
+			cond_resched();
 		}
 
 		cpus_read_lock();
@@ -2204,12 +2294,17 @@
 		 */
 		synchronize_rcu();
 		for_each_buffer_cpu(buffer, cpu) {
+			unsigned long flags;
+
 			cpu_buffer = buffer->buffers[cpu];
+			raw_spin_lock_irqsave(&cpu_buffer->reader_lock, flags);
 			rb_check_pages(cpu_buffer);
+			raw_spin_unlock_irqrestore(&cpu_buffer->reader_lock, flags);
 		}
 		atomic_dec(&buffer->record_disabled);
 	}
 
+	atomic_dec(&buffer->resizing);
 	mutex_unlock(&buffer->mutex);
 	return 0;
 
@@ -2230,6 +2325,7 @@
 		}
 	}
  out_err_unlock:
+	atomic_dec(&buffer->resizing);
 	mutex_unlock(&buffer->mutex);
 	return err;
 }
@@ -2258,11 +2354,6 @@
 			       cpu_buffer->reader_page->read);
 }
 
-static __always_inline unsigned rb_page_commit(struct buffer_page *bpage)
-{
-	return local_read(&bpage->page->commit);
-}
-
 static struct ring_buffer_event *
 rb_iter_head_event(struct ring_buffer_iter *iter)
 {
@@ -2281,6 +2372,11 @@
 	 */
 	commit = rb_page_commit(iter_head_page);
 	smp_rmb();
+
+	/* An event needs to be at least 8 bytes in size */
+	if (iter->head > commit - 8)
+		goto reset;
+
 	event = __rb_page_index(iter_head_page, iter->head);
 	length = rb_event_length(event);
 
@@ -2290,7 +2386,7 @@
 	 */
 	barrier();
 
-	if ((iter->head + length) > commit || length > BUF_MAX_DATA_SIZE)
+	if ((iter->head + length) > commit || length > BUF_PAGE_SIZE)
 		/* Writer corrupted the read? */
 		goto reset;
 
@@ -2403,7 +2499,8 @@
 		 * the counters.
 		 */
 		local_add(entries, &cpu_buffer->overrun);
-		local_sub(BUF_PAGE_SIZE, &cpu_buffer->entries_bytes);
+		local_sub(rb_page_commit(next_page), &cpu_buffer->entries_bytes);
+		local_inc(&cpu_buffer->pages_lost);
 
 		/*
 		 * The entries will be zeroed out when we move the
@@ -2545,9 +2642,6 @@
 
 	event = __rb_page_index(tail_page, tail);
 
-	/* account for padding bytes */
-	local_add(BUF_PAGE_SIZE - tail, &cpu_buffer->entries_bytes);
-
 	/*
 	 * Save the original length to the meta data.
 	 * This will be used by the reader to add lost event
@@ -2561,7 +2655,8 @@
 	 * write counter enough to allow another writer to slip
 	 * in on this page.
 	 * We put in a discarded commit instead, to make sure
-	 * that this space is not used again.
+	 * that this space is not used again, and this space will
+	 * not be accounted into 'entries_bytes'.
 	 *
 	 * If we are less than the minimum size, we don't need to
 	 * worry about it.
@@ -2572,6 +2667,9 @@
 		/* Mark the rest of the page with padding */
 		rb_event_set_padding(event);
 
+		/* Make sure the padding is visible before the write update */
+		smp_wmb();
+
 		/* Set the write back to the previous setting */
 		local_sub(length, &tail_page->write);
 		return;
@@ -2583,6 +2681,12 @@
 	/* time delta must be non zero */
 	event->time_delta = 1;
 
+	/* account for padding bytes */
+	local_add(BUF_PAGE_SIZE - tail, &cpu_buffer->entries_bytes);
+
+	/* Make sure the padding is visible before the tail_page->write update */
+	smp_wmb();
+
 	/* Set write to end of buffer */
 	length = (tail + length) - BUF_PAGE_SIZE;
 	local_sub(length, &tail_page->write);
@@ -2849,25 +2953,6 @@
 	return length;
 }
 
-static u64 rb_time_delta(struct ring_buffer_event *event)
-{
-	switch (event->type_len) {
-	case RINGBUF_TYPE_PADDING:
-		return 0;
-
-	case RINGBUF_TYPE_TIME_EXTEND:
-		return rb_event_time_stamp(event);
-
-	case RINGBUF_TYPE_TIME_STAMP:
-		return 0;
-
-	case RINGBUF_TYPE_DATA:
-		return event->time_delta;
-	default:
-		return 0;
-	}
-}
-
 static inline int
 rb_try_to_discard(struct ring_buffer_per_cpu *cpu_buffer,
 		  struct ring_buffer_event *event)
@@ -2876,8 +2961,6 @@
 	struct buffer_page *bpage;
 	unsigned long index;
 	unsigned long addr;
-	u64 write_stamp;
-	u64 delta;
 
 	new_index = rb_event_index(event);
 	old_index = new_index + rb_event_ts_length(event);
@@ -2886,41 +2969,34 @@
 
 	bpage = READ_ONCE(cpu_buffer->tail_page);
 
-	delta = rb_time_delta(event);
-
-	if (!rb_time_read(&cpu_buffer->write_stamp, &write_stamp))
-		return 0;
-
-	/* Make sure the write stamp is read before testing the location */
-	barrier();
-
+	/*
+	 * Make sure the tail_page is still the same and
+	 * the next write location is the end of this event
+	 */
 	if (bpage->page == (void *)addr && rb_page_write(bpage) == old_index) {
 		unsigned long write_mask =
 			local_read(&bpage->write) & ~RB_WRITE_MASK;
 		unsigned long event_length = rb_event_length(event);
 
-		/* Something came in, can't discard */
-		if (!rb_time_cmpxchg(&cpu_buffer->write_stamp,
-				       write_stamp, write_stamp - delta))
-			return 0;
-
 		/*
-		 * It's possible that the event time delta is zero
-		 * (has the same time stamp as the previous event)
-		 * in which case write_stamp and before_stamp could
-		 * be the same. In such a case, force before_stamp
-		 * to be different than write_stamp. It doesn't
-		 * matter what it is, as long as its different.
+		 * For the before_stamp to be different than the write_stamp
+		 * to make sure that the next event adds an absolute
+		 * value and does not rely on the saved write stamp, which
+		 * is now going to be bogus.
+		 *
+		 * By setting the before_stamp to zero, the next event
+		 * is not going to use the write_stamp and will instead
+		 * create an absolute timestamp. This means there's no
+		 * reason to update the wirte_stamp!
 		 */
-		if (!delta)
-			rb_time_set(&cpu_buffer->before_stamp, 0);
+		rb_time_set(&cpu_buffer->before_stamp, 0);
 
 		/*
 		 * If an event were to come in now, it would see that the
 		 * write_stamp and the before_stamp are different, and assume
 		 * that this event just added itself before updating
 		 * the write stamp. The interrupting event will fix the
-		 * write stamp for us, and use the before stamp as its delta.
+		 * write stamp for us, and use an absolute timestamp.
 		 */
 
 		/*
@@ -2971,6 +3047,10 @@
 		if (RB_WARN_ON(cpu_buffer,
 			       rb_is_reader_page(cpu_buffer->tail_page)))
 			return;
+		/*
+		 * No need for a memory barrier here, as the update
+		 * of the tail_page did it for this page.
+		 */
 		local_set(&cpu_buffer->commit_page->page->commit,
 			  rb_page_write(cpu_buffer->commit_page));
 		rb_inc_page(&cpu_buffer->commit_page);
@@ -2980,6 +3060,8 @@
 	while (rb_commit_index(cpu_buffer) !=
 	       rb_page_write(cpu_buffer->commit_page)) {
 
+		/* Make sure the readers see the content of what is committed. */
+		smp_wmb();
 		local_set(&cpu_buffer->commit_page->page->commit,
 			  rb_page_write(cpu_buffer->commit_page));
 		RB_WARN_ON(cpu_buffer,
@@ -3055,10 +3137,6 @@
 static __always_inline void
 rb_wakeups(struct trace_buffer *buffer, struct ring_buffer_per_cpu *cpu_buffer)
 {
-	size_t nr_pages;
-	size_t dirty;
-	size_t full;
-
 	if (buffer->irq_work.waiters_pending) {
 		buffer->irq_work.waiters_pending = false;
 		/* irq_work_queue() supplies it's own memory barriers */
@@ -3082,10 +3160,7 @@
 
 	cpu_buffer->last_pages_touch = local_read(&cpu_buffer->pages_touched);
 
-	full = cpu_buffer->shortest_full;
-	nr_pages = cpu_buffer->nr_pages;
-	dirty = ring_buffer_nr_dirty_pages(buffer, cpu_buffer->cpu);
-	if (full && nr_pages && (dirty * 100) <= full * nr_pages)
+	if (!full_hit(buffer, cpu_buffer->cpu, cpu_buffer->shortest_full))
 		return;
 
 	cpu_buffer->irq_work.wakeup_full = true;
@@ -3167,14 +3242,9 @@
 trace_recursive_lock(struct ring_buffer_per_cpu *cpu_buffer)
 {
 	unsigned int val = cpu_buffer->current_context;
-	unsigned long pc = preempt_count();
-	int bit;
+	int bit = interrupt_context_level();
 
-	if (!(pc & (NMI_MASK | HARDIRQ_MASK | SOFTIRQ_OFFSET)))
-		bit = RB_CTX_NORMAL;
-	else
-		bit = pc & NMI_MASK ? RB_CTX_NMI :
-			pc & HARDIRQ_MASK ? RB_CTX_IRQ : RB_CTX_SOFTIRQ;
+	bit = RB_CTX_NORMAL - bit;
 
 	if (unlikely(val & (1 << (bit + cpu_buffer->nest)))) {
 		/*
@@ -3365,7 +3435,7 @@
 		return;
 
 	/*
-	 * If this interrupted another event, 
+	 * If this interrupted another event,
 	 */
 	if (atomic_inc_return(this_cpu_ptr(&checking)) != 1)
 		goto out;
@@ -3459,7 +3529,10 @@
 		 * absolute timestamp.
 		 * Don't bother if this is the start of a new page (w == 0).
 		 */
-		if (unlikely(!a_ok || !b_ok || (info->before != info->after && w))) {
+		if (!w) {
+			/* Use the sub-buffer timestamp */
+			info->delta = 0;
+		} else if (unlikely(!a_ok || !b_ok || info->before != info->after)) {
 			info->add_timestamp |= RB_ADD_STAMP_FORCE | RB_ADD_STAMP_EXTEND;
 			info->length += RB_LEN_TIME_EXTEND;
 		} else {
@@ -3482,26 +3555,19 @@
 
 	/* See if we shot pass the end of this buffer page */
 	if (unlikely(write > BUF_PAGE_SIZE)) {
-		/* before and after may now different, fix it up*/
-		b_ok = rb_time_read(&cpu_buffer->before_stamp, &info->before);
-		a_ok = rb_time_read(&cpu_buffer->write_stamp, &info->after);
-		if (a_ok && b_ok && info->before != info->after)
-			(void)rb_time_cmpxchg(&cpu_buffer->before_stamp,
-					      info->before, info->after);
-		if (a_ok && b_ok)
-			check_buffer(cpu_buffer, info, CHECK_FULL_PAGE);
+		check_buffer(cpu_buffer, info, CHECK_FULL_PAGE);
 		return rb_move_tail(cpu_buffer, tail, info);
 	}
 
 	if (likely(tail == w)) {
-		u64 save_before;
-		bool s_ok;
-
 		/* Nothing interrupted us between A and C */
  /*D*/		rb_time_set(&cpu_buffer->write_stamp, info->ts);
-		barrier();
- /*E*/		s_ok = rb_time_read(&cpu_buffer->before_stamp, &save_before);
-		RB_WARN_ON(cpu_buffer, !s_ok);
+		/*
+		 * If something came in between C and D, the write stamp
+		 * may now not be in sync. But that's fine as the before_stamp
+		 * will be different and then next event will just be forced
+		 * to use an absolute timestamp.
+		 */
 		if (likely(!(info->add_timestamp &
 			     (RB_ADD_STAMP_FORCE | RB_ADD_STAMP_ABSOLUTE))))
 			/* This did not interrupt any time update */
@@ -3509,41 +3575,40 @@
 		else
 			/* Just use full timestamp for interrupting event */
 			info->delta = info->ts;
-		barrier();
 		check_buffer(cpu_buffer, info, tail);
-		if (unlikely(info->ts != save_before)) {
-			/* SLOW PATH - Interrupted between C and E */
-
-			a_ok = rb_time_read(&cpu_buffer->write_stamp, &info->after);
-			RB_WARN_ON(cpu_buffer, !a_ok);
-
-			/* Write stamp must only go forward */
-			if (save_before > info->after) {
-				/*
-				 * We do not care about the result, only that
-				 * it gets updated atomically.
-				 */
-				(void)rb_time_cmpxchg(&cpu_buffer->write_stamp,
-						      info->after, save_before);
-			}
-		}
 	} else {
 		u64 ts;
 		/* SLOW PATH - Interrupted between A and C */
-		a_ok = rb_time_read(&cpu_buffer->write_stamp, &info->after);
-		/* Was interrupted before here, write_stamp must be valid */
+
+		/* Save the old before_stamp */
+		a_ok = rb_time_read(&cpu_buffer->before_stamp, &info->before);
 		RB_WARN_ON(cpu_buffer, !a_ok);
+
+		/*
+		 * Read a new timestamp and update the before_stamp to make
+		 * the next event after this one force using an absolute
+		 * timestamp. This is in case an interrupt were to come in
+		 * between E and F.
+		 */
 		ts = rb_time_stamp(cpu_buffer->buffer);
+		rb_time_set(&cpu_buffer->before_stamp, ts);
+
+		barrier();
+ /*E*/		a_ok = rb_time_read(&cpu_buffer->write_stamp, &info->after);
+		/* Was interrupted before here, write_stamp must be valid */
+		RB_WARN_ON(cpu_buffer, !a_ok);
 		barrier();
- /*E*/		if (write == (local_read(&tail_page->write) & RB_WRITE_MASK) &&
-		    info->after < ts &&
-		    rb_time_cmpxchg(&cpu_buffer->write_stamp,
-				    info->after, ts)) {
-			/* Nothing came after this event between C and E */
+ /*F*/		if (write == (local_read(&tail_page->write) & RB_WRITE_MASK) &&
+		    info->after == info->before && info->after < ts) {
+			/*
+			 * Nothing came after this event between C and F, it is
+			 * safe to use info->after for the delta as it
+			 * matched info->before and is still valid.
+			 */
 			info->delta = ts - info->after;
 		} else {
 			/*
-			 * Interrupted between C and E:
+			 * Interrupted between C and F:
 			 * Lost the previous events time stamp. Just set the
 			 * delta to zero, and this will be the same time as
 			 * the event this event interrupted. And the events that
@@ -3594,6 +3659,12 @@
 	int nr_loops = 0;
 	int add_ts_default;
 
+	/* ring buffer does cmpxchg, make sure it is safe in NMI context */
+	if (!IS_ENABLED(CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG) &&
+	    (unlikely(in_nmi()))) {
+		return NULL;
+	}
+
 	rb_start_commit(cpu_buffer);
 	/* The commit page can not change after this */
 
@@ -3617,6 +3688,8 @@
 	if (ring_buffer_time_stamp_abs(cpu_buffer->buffer)) {
 		add_ts_default = RB_ADD_STAMP_ABSOLUTE;
 		info.length += RB_LEN_TIME_EXTEND;
+		if (info.length > BUF_MAX_DATA_SIZE)
+			goto out_fail;
 	} else {
 		add_ts_default = RB_ADD_STAMP_NONE;
 	}
@@ -4096,7 +4169,7 @@
 EXPORT_SYMBOL_GPL(ring_buffer_oldest_event_ts);
 
 /**
- * ring_buffer_bytes_cpu - get the number of bytes consumed in a cpu buffer
+ * ring_buffer_bytes_cpu - get the number of bytes unconsumed in a cpu buffer
  * @buffer: The ring buffer
  * @cpu: The per CPU buffer to read from.
  */
@@ -4274,6 +4347,7 @@
 
 	iter->cache_reader_page = iter->head_page;
 	iter->cache_read = cpu_buffer->read;
+	iter->cache_pages_removed = cpu_buffer->pages_removed;
 
 	if (iter->head) {
 		iter->read_stamp = cpu_buffer->read_stamp;
@@ -4325,7 +4399,7 @@
 	cpu_buffer = iter->cpu_buffer;
 	reader = cpu_buffer->reader_page;
 	head_page = cpu_buffer->head_page;
-	commit_page = cpu_buffer->commit_page;
+	commit_page = READ_ONCE(cpu_buffer->commit_page);
 	commit_ts = commit_page->page->time_stamp;
 
 	/*
@@ -4547,6 +4621,38 @@
 	arch_spin_unlock(&cpu_buffer->lock);
 	local_irq_restore(flags);
 
+	/*
+	 * The writer has preempt disable, wait for it. But not forever
+	 * Although, 1 second is pretty much "forever"
+	 */
+#define USECS_WAIT	1000000
+        for (nr_loops = 0; nr_loops < USECS_WAIT; nr_loops++) {
+		/* If the write is past the end of page, a writer is still updating it */
+		if (likely(!reader || rb_page_write(reader) <= BUF_PAGE_SIZE))
+			break;
+
+		udelay(1);
+
+		/* Get the latest version of the reader write value */
+		smp_rmb();
+	}
+
+	/* The writer is not moving forward? Something is wrong */
+	if (RB_WARN_ON(cpu_buffer, nr_loops == USECS_WAIT))
+		reader = NULL;
+
+	/*
+	 * Make sure we see any padding after the write update
+	 * (see rb_reset_tail()).
+	 *
+	 * In addition, a writer may be writing on the reader page
+	 * if the page has not been fully filled, so the read barrier
+	 * is also needed to make sure we see the content of what is
+	 * committed by the writer (see rb_set_commit_to_write()).
+	 */
+	smp_rmb();
+
+
 	return reader;
 }
 
@@ -4571,6 +4677,7 @@
 
 	length = rb_event_length(event);
 	cpu_buffer->reader_page->read += length;
+	cpu_buffer->read_bytes += length;
 }
 
 static void rb_advance_iter(struct ring_buffer_iter *iter)
@@ -4695,12 +4802,13 @@
 	buffer = cpu_buffer->buffer;
 
 	/*
-	 * Check if someone performed a consuming read to
-	 * the buffer. A consuming read invalidates the iterator
-	 * and we need to reset the iterator in this case.
+	 * Check if someone performed a consuming read to the buffer
+	 * or removed some pages from the buffer. In these cases,
+	 * iterator was invalidated and we need to reset it.
 	 */
 	if (unlikely(iter->cache_read != cpu_buffer->read ||
-		     iter->cache_reader_page != cpu_buffer->reader_page))
+		     iter->cache_reader_page != cpu_buffer->reader_page ||
+		     iter->cache_pages_removed != cpu_buffer->pages_removed))
 		rb_iter_reset(iter);
 
  again:
@@ -4962,7 +5070,8 @@
 	if (!iter)
 		return NULL;
 
-	iter->event = kmalloc(BUF_MAX_DATA_SIZE, flags);
+	/* Holds the entire event: data and meta data */
+	iter->event = kmalloc(BUF_PAGE_SIZE, flags);
 	if (!iter->event) {
 		kfree(iter);
 		return NULL;
@@ -5091,28 +5200,34 @@
 }
 EXPORT_SYMBOL_GPL(ring_buffer_size);
 
+static void rb_clear_buffer_page(struct buffer_page *page)
+{
+	local_set(&page->write, 0);
+	local_set(&page->entries, 0);
+	rb_init_page(page->page);
+	page->read = 0;
+}
+
 static void
 rb_reset_cpu(struct ring_buffer_per_cpu *cpu_buffer)
 {
+	struct buffer_page *page;
+
 	rb_head_page_deactivate(cpu_buffer);
 
 	cpu_buffer->head_page
 		= list_entry(cpu_buffer->pages, struct buffer_page, list);
-	local_set(&cpu_buffer->head_page->write, 0);
-	local_set(&cpu_buffer->head_page->entries, 0);
-	local_set(&cpu_buffer->head_page->page->commit, 0);
-
-	cpu_buffer->head_page->read = 0;
+	rb_clear_buffer_page(cpu_buffer->head_page);
+	list_for_each_entry(page, cpu_buffer->pages, list) {
+		rb_clear_buffer_page(page);
+	}
 
 	cpu_buffer->tail_page = cpu_buffer->head_page;
 	cpu_buffer->commit_page = cpu_buffer->head_page;
 
 	INIT_LIST_HEAD(&cpu_buffer->reader_page->list);
 	INIT_LIST_HEAD(&cpu_buffer->new_pages);
-	local_set(&cpu_buffer->reader_page->write, 0);
-	local_set(&cpu_buffer->reader_page->entries, 0);
-	local_set(&cpu_buffer->reader_page->page->commit, 0);
-	cpu_buffer->reader_page->read = 0;
+	rb_clear_buffer_page(cpu_buffer->reader_page);
 
 	local_set(&cpu_buffer->entries_bytes, 0);
 	local_set(&cpu_buffer->overrun, 0);
@@ -5122,6 +5237,7 @@
 	local_set(&cpu_buffer->committing, 0);
 	local_set(&cpu_buffer->commits, 0);
 	local_set(&cpu_buffer->pages_touched, 0);
+	local_set(&cpu_buffer->pages_lost, 0);
 	local_set(&cpu_buffer->pages_read, 0);
 	cpu_buffer->last_pages_touch = 0;
 	cpu_buffer->shortest_full = 0;
@@ -5137,6 +5253,7 @@
 	cpu_buffer->last_overrun = 0;
 
 	rb_head_page_activate(cpu_buffer);
+	cpu_buffer->pages_removed = 0;
 }
 
 /* Must have disabled the cpu buffer then done a synchronize_rcu */
@@ -5189,6 +5306,9 @@
 }
 EXPORT_SYMBOL_GPL(ring_buffer_reset_cpu);
 
+/* Flag to ensure proper resetting of atomic variables */
+#define RESET_BIT	(1 << 30)
+
 /**
  * ring_buffer_reset_cpu - reset a ring buffer per CPU buffer
  * @buffer: The ring buffer to reset a per cpu buffer of
@@ -5205,20 +5325,27 @@
 	for_each_online_buffer_cpu(buffer, cpu) {
 		cpu_buffer = buffer->buffers[cpu];
 
-		atomic_inc(&cpu_buffer->resize_disabled);
+		atomic_add(RESET_BIT, &cpu_buffer->resize_disabled);
 		atomic_inc(&cpu_buffer->record_disabled);
 	}
 
 	/* Make sure all commits have finished */
 	synchronize_rcu();
 
-	for_each_online_buffer_cpu(buffer, cpu) {
+	for_each_buffer_cpu(buffer, cpu) {
 		cpu_buffer = buffer->buffers[cpu];
 
+		/*
+		 * If a CPU came online during the synchronize_rcu(), then
+		 * ignore it.
+		 */
+		if (!(atomic_read(&cpu_buffer->resize_disabled) & RESET_BIT))
+			continue;
+
 		reset_disabled_cpu_buffer(cpu_buffer);
 
 		atomic_dec(&cpu_buffer->record_disabled);
-		atomic_dec(&cpu_buffer->resize_disabled);
+		atomic_sub(RESET_BIT, &cpu_buffer->resize_disabled);
 	}
 
 	mutex_unlock(&buffer->mutex);
@@ -5233,6 +5360,9 @@
 	struct ring_buffer_per_cpu *cpu_buffer;
 	int cpu;
 
+	/* prevent another thread from changing buffer sizes */
+	mutex_lock(&buffer->mutex);
+
 	for_each_buffer_cpu(buffer, cpu) {
 		cpu_buffer = buffer->buffers[cpu];
 
@@ -5251,6 +5381,8 @@
 		atomic_dec(&cpu_buffer->record_disabled);
 		atomic_dec(&cpu_buffer->resize_disabled);
 	}
+
+	mutex_unlock(&buffer->mutex);
 }
 EXPORT_SYMBOL_GPL(ring_buffer_reset);
 
@@ -5368,6 +5500,15 @@
 	if (local_read(&cpu_buffer_b->committing))
 		goto out_dec;
 
+	/*
+	 * When resize is in progress, we cannot swap it because
+	 * it will mess the state of the cpu buffer.
+	 */
+	if (atomic_read(&buffer_a->resizing))
+		goto out_dec;
+	if (atomic_read(&buffer_b->resizing))
+		goto out_dec;
+
 	buffer_a->buffers[cpu] = cpu_buffer_b;
 	buffer_b->buffers[cpu] = cpu_buffer_a;
 
@@ -5450,11 +5591,16 @@
  */
 void ring_buffer_free_read_page(struct trace_buffer *buffer, int cpu, void *data)
 {
-	struct ring_buffer_per_cpu *cpu_buffer = buffer->buffers[cpu];
+	struct ring_buffer_per_cpu *cpu_buffer;
 	struct buffer_data_page *bpage = data;
 	struct page *page = virt_to_page(bpage);
 	unsigned long flags;
 
+	if (!buffer || !buffer->buffers || !buffer->buffers[cpu])
+		return;
+
+	cpu_buffer = buffer->buffers[cpu];
+
 	/* If the page is still in use someplace else, we can't reuse it */
 	if (page_ref_count(page) > 1)
 		goto out;
@@ -5569,7 +5715,15 @@
 		unsigned int pos = 0;
 		unsigned int size;
 
-		if (full)
+		/*
+		 * If a full page is expected, this can still be returned
+		 * if there's been a previous partial read and the
+		 * rest of the page can be read and the commit page is off
+		 * the reader page.
+		 */
+		if (full &&
+		    (!read || (len < (commit - read)) ||
+		     cpu_buffer->reader_page == cpu_buffer->commit_page))
 			goto out_unlock;
 
 		if (len > (commit - read))
@@ -5618,7 +5772,7 @@
 	} else {
 		/* update the entry counter */
 		cpu_buffer->read += rb_page_entries(reader);
-		cpu_buffer->read_bytes += BUF_PAGE_SIZE;
+		cpu_buffer->read_bytes += rb_page_commit(reader);
 
 		/* swap the pages */
 		rb_init_page(bpage);
@@ -5795,9 +5949,9 @@
 		/* Ignore dropped events before test starts. */
 		if (started) {
 			if (nested)
-				data->bytes_dropped += len;
-			else
 				data->bytes_dropped_nested += len;
+			else
+				data->bytes_dropped += len;
 		}
 		return len;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/synth_event_gen_test.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/synth_event_gen_test.c
@@ -120,15 +120,13 @@
 
 	/* Now generate a gen_synth_test event */
 	ret = synth_event_trace_array(gen_synth_test, vals, ARRAY_SIZE(vals));
- out:
+ free:
+	kfree(buf);
 	return ret;
  delete:
 	/* We got an error after creating the event, delete it */
 	synth_event_delete("gen_synth_test");
- free:
-	kfree(buf);
-
-	goto out;
+	goto free;
 }
 
 /*
@@ -227,15 +225,13 @@
 
 	/* Now trace an empty_synth_test event */
 	ret = synth_event_trace_array(empty_synth_test, vals, ARRAY_SIZE(vals));
- out:
+ free:
+	kfree(buf);
 	return ret;
  delete:
 	/* We got an error after creating the event, delete it */
 	synth_event_delete("empty_synth_test");
- free:
-	kfree(buf);
-
-	goto out;
+	goto free;
 }
 
 static struct synth_field_desc create_synth_test_fields[] = {
@@ -481,6 +477,17 @@
 
 	ret = test_trace_synth_event();
 	WARN_ON(ret);
+
+	/* Disable when done */
+	trace_array_set_clr_event(gen_synth_test->tr,
+				  "synthetic",
+				  "gen_synth_test", false);
+	trace_array_set_clr_event(empty_synth_test->tr,
+				  "synthetic",
+				  "empty_synth_test", false);
+	trace_array_set_clr_event(create_synth_test->tr,
+				  "synthetic",
+				  "create_synth_test", false);
  out:
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace.c
@@ -40,6 +40,7 @@
 #include <linux/ctype.h>
 #include <linux/init.h>
 #include <linux/panic_notifier.h>
+#include <linux/kmemleak.h>
 #include <linux/poll.h>
 #include <linux/nmi.h>
 #include <linux/fs.h>
@@ -235,7 +236,7 @@
 static int __init set_trace_boot_options(char *str)
 {
 	strlcpy(trace_boot_options_buf, str, MAX_TRACER_SIZE);
-	return 0;
+	return 1;
 }
 __setup("trace_options=", set_trace_boot_options);
 
@@ -246,12 +247,16 @@
 {
 	strlcpy(trace_boot_clock_buf, str, MAX_TRACER_SIZE);
 	trace_boot_clock = trace_boot_clock_buf;
-	return 0;
+	return 1;
 }
 __setup("trace_clock=", set_trace_boot_clock);
 
 static int __init set_tracepoint_printk(char *str)
 {
+	/* Ignore the "tp_printk_stop_on_boot" param */
+	if (*str == '_')
+		return 0;
+
 	if ((strcmp(str, "=0") != 0 && strcmp(str, "=off") != 0))
 		tracepoint_printk = 1;
 	return 1;
@@ -512,12 +517,6 @@
 	return 0;
 }
 
-void trace_free_pid_list(struct trace_pid_list *pid_list)
-{
-	vfree(pid_list->pids);
-	kfree(pid_list);
-}
-
 /**
  * trace_find_filtered_pid - check if a pid exists in a filtered_pid list
  * @filtered_pids: The list of pids to check
@@ -528,14 +527,7 @@
 bool
 trace_find_filtered_pid(struct trace_pid_list *filtered_pids, pid_t search_pid)
 {
-	/*
-	 * If pid_max changed after filtered_pids was created, we
-	 * by default ignore all pids greater than the previous pid_max.
-	 */
-	if (search_pid >= filtered_pids->pid_max)
-		return false;
-
-	return test_bit(search_pid, filtered_pids->pids);
+	return trace_pid_list_is_set(filtered_pids, search_pid);
 }
 
 /**
@@ -592,15 +584,11 @@
 			return;
 	}
 
-	/* Sorry, but we don't support pid_max changing after setting */
-	if (task->pid >= pid_list->pid_max)
-		return;
-
 	/* "self" is set for forks, and NULL for exits */
 	if (self)
-		set_bit(task->pid, pid_list->pids);
+		trace_pid_list_set(pid_list, task->pid);
 	else
-		clear_bit(task->pid, pid_list->pids);
+		trace_pid_list_clear(pid_list, task->pid);
 }
 
 /**
@@ -617,18 +605,19 @@
  */
 void *trace_pid_next(struct trace_pid_list *pid_list, void *v, loff_t *pos)
 {
-	unsigned long pid = (unsigned long)v;
+	long pid = (unsigned long)v;
+	unsigned int next;
 
 	(*pos)++;
 
 	/* pid already is +1 of the actual previous bit */
-	pid = find_next_bit(pid_list->pids, pid_list->pid_max, pid);
+	if (trace_pid_list_next(pid_list, pid, &next) < 0)
+		return NULL;
 
-	/* Return pid + 1 to allow zero to be represented */
-	if (pid < pid_list->pid_max)
-		return (void *)(pid + 1);
+	pid = next;
 
-	return NULL;
+	/* Return pid + 1 to allow zero to be represented */
+	return (void *)(pid + 1);
 }
 
 /**
@@ -645,12 +634,14 @@
 void *trace_pid_start(struct trace_pid_list *pid_list, loff_t *pos)
 {
 	unsigned long pid;
+	unsigned int first;
 	loff_t l = 0;
 
-	pid = find_first_bit(pid_list->pids, pid_list->pid_max);
-	if (pid >= pid_list->pid_max)
+	if (trace_pid_list_first(pid_list, &first) < 0)
 		return NULL;
 
+	pid = first;
+
 	/* Return pid + 1 so that zero can be the exit value */
 	for (pid++; pid && l < *pos;
 	     pid = (unsigned long)trace_pid_next(pid_list, (void *)pid, &l))
@@ -686,7 +677,7 @@
 	unsigned long val;
 	int nr_pids = 0;
 	ssize_t read = 0;
-	ssize_t ret = 0;
+	ssize_t ret;
 	loff_t pos;
 	pid_t pid;
 
@@ -699,55 +690,48 @@
 	 * the user. If the operation fails, then the current list is
 	 * not modified.
 	 */
-	pid_list = kmalloc(sizeof(*pid_list), GFP_KERNEL);
+	pid_list = trace_pid_list_alloc();
 	if (!pid_list) {
 		trace_parser_put(&parser);
 		return -ENOMEM;
 	}
 
-	pid_list->pid_max = READ_ONCE(pid_max);
-
-	/* Only truncating will shrink pid_max */
-	if (filtered_pids && filtered_pids->pid_max > pid_list->pid_max)
-		pid_list->pid_max = filtered_pids->pid_max;
-
-	pid_list->pids = vzalloc((pid_list->pid_max + 7) >> 3);
-	if (!pid_list->pids) {
-		trace_parser_put(&parser);
-		kfree(pid_list);
-		return -ENOMEM;
-	}
-
 	if (filtered_pids) {
 		/* copy the current bits to the new max */
-		for_each_set_bit(pid, filtered_pids->pids,
-				 filtered_pids->pid_max) {
-			set_bit(pid, pid_list->pids);
+		ret = trace_pid_list_first(filtered_pids, &pid);
+		while (!ret) {
+			trace_pid_list_set(pid_list, pid);
+			ret = trace_pid_list_next(filtered_pids, pid + 1, &pid);
 			nr_pids++;
 		}
 	}
 
+	ret = 0;
 	while (cnt > 0) {
 
 		pos = 0;
 
 		ret = trace_get_user(&parser, ubuf, cnt, &pos);
-		if (ret < 0 || !trace_parser_loaded(&parser))
+		if (ret < 0)
 			break;
 
 		read += ret;
 		ubuf += ret;
 		cnt -= ret;
 
+		if (!trace_parser_loaded(&parser))
+			break;
+
 		ret = -EINVAL;
 		if (kstrtoul(parser.buffer, 0, &val))
 			break;
-		if (val >= pid_list->pid_max)
-			break;
 
 		pid = (pid_t)val;
 
-		set_bit(pid, pid_list->pids);
+		if (trace_pid_list_set(pid_list, pid) < 0) {
+			ret = -1;
+			break;
+		}
 		nr_pids++;
 
 		trace_parser_clear(&parser);
@@ -756,14 +740,13 @@
 	trace_parser_put(&parser);
 
 	if (ret < 0) {
-		trace_free_pid_list(pid_list);
+		trace_pid_list_free(pid_list);
 		return ret;
 	}
 
 	if (!nr_pids) {
 		/* Cleared the list of pids */
-		trace_free_pid_list(pid_list);
-		read = ret;
+		trace_pid_list_free(pid_list);
 		pid_list = NULL;
 	}
 
@@ -1008,13 +991,8 @@
 		ring_buffer_unlock_commit(buffer, event);
 }
 
-/**
- * __trace_puts - write a constant string into the trace buffer.
- * @ip:	   The address of the caller
- * @str:   The constant string to write
- * @size:  The size of the string.
- */
-int __trace_puts(unsigned long ip, const char *str, int size)
+int __trace_array_puts(struct trace_array *tr, unsigned long ip,
+		       const char *str, int size)
 {
 	struct ring_buffer_event *event;
 	struct trace_buffer *buffer;
@@ -1022,7 +1000,7 @@
 	unsigned int trace_ctx;
 	int alloc;
 
-	if (!(global_trace.trace_flags & TRACE_ITER_PRINTK))
+	if (!(tr->trace_flags & TRACE_ITER_PRINTK))
 		return 0;
 
 	if (unlikely(tracing_selftest_running || tracing_disabled))
@@ -1031,7 +1009,7 @@
 	alloc = sizeof(*entry) + size + 2; /* possible \n added */
 
 	trace_ctx = tracing_gen_ctx();
-	buffer = global_trace.array_buffer.buffer;
+	buffer = tr->array_buffer.buffer;
 	ring_buffer_nest_start(buffer);
 	event = __trace_buffer_lock_reserve(buffer, TRACE_PRINT, alloc,
 					    trace_ctx);
@@ -1053,11 +1031,23 @@
 		entry->buf[size] = '\0';
 
 	__buffer_unlock_commit(buffer, event);
-	ftrace_trace_stack(&global_trace, buffer, trace_ctx, 4, NULL);
+	ftrace_trace_stack(tr, buffer, trace_ctx, 4, NULL);
  out:
 	ring_buffer_nest_end(buffer);
 	return size;
 }
+EXPORT_SYMBOL_GPL(__trace_array_puts);
+
+/**
+ * __trace_puts - write a constant string into the trace buffer.
+ * @ip:	   The address of the caller
+ * @str:   The constant string to write
+ * @size:  The size of the string.
+ */
+int __trace_puts(unsigned long ip, const char *str, int size)
+{
+	return __trace_array_puts(&global_trace, ip, str, size);
+}
 EXPORT_SYMBOL_GPL(__trace_puts);
 
 /**
@@ -1111,22 +1101,22 @@
 	unsigned long flags;
 
 	if (in_nmi()) {
-		internal_trace_puts("*** SNAPSHOT CALLED FROM NMI CONTEXT ***\n");
-		internal_trace_puts("*** snapshot is being ignored        ***\n");
+		trace_array_puts(tr, "*** SNAPSHOT CALLED FROM NMI CONTEXT ***\n");
+		trace_array_puts(tr, "*** snapshot is being ignored        ***\n");
 		return;
 	}
 
 	if (!tr->allocated_snapshot) {
-		internal_trace_puts("*** SNAPSHOT NOT ALLOCATED ***\n");
-		internal_trace_puts("*** stopping trace here!   ***\n");
-		tracing_off();
+		trace_array_puts(tr, "*** SNAPSHOT NOT ALLOCATED ***\n");
+		trace_array_puts(tr, "*** stopping trace here!   ***\n");
+		tracer_tracing_off(tr);
 		return;
 	}
 
 	/* Note, snapshot can not be used when the tracer uses it */
 	if (tracer->use_max_tr) {
-		internal_trace_puts("*** LATENCY TRACER ACTIVE ***\n");
-		internal_trace_puts("*** Can not use snapshot (sorry) ***\n");
+		trace_array_puts(tr, "*** LATENCY TRACER ACTIVE ***\n");
+		trace_array_puts(tr, "*** Can not use snapshot (sorry) ***\n");
 		return;
 	}
 
@@ -1199,12 +1189,14 @@
 {
 	void *cond_data = NULL;
 
+	local_irq_disable();
 	arch_spin_lock(&tr->max_lock);
 
 	if (tr->cond_snapshot)
 		cond_data = tr->cond_snapshot->cond_data;
 
 	arch_spin_unlock(&tr->max_lock);
+	local_irq_enable();
 
 	return cond_data;
 }
@@ -1340,9 +1332,11 @@
 		goto fail_unlock;
 	}
 
+	local_irq_disable();
 	arch_spin_lock(&tr->max_lock);
 	tr->cond_snapshot = cond_snapshot;
 	arch_spin_unlock(&tr->max_lock);
+	local_irq_enable();
 
 	mutex_unlock(&trace_types_lock);
 
@@ -1369,6 +1363,7 @@
 {
 	int ret = 0;
 
+	local_irq_disable();
 	arch_spin_lock(&tr->max_lock);
 
 	if (!tr->cond_snapshot)
@@ -1379,6 +1374,7 @@
 	}
 
 	arch_spin_unlock(&tr->max_lock);
+	local_irq_enable();
 
 	return ret;
 }
@@ -1421,6 +1417,7 @@
 	return false;
 }
 EXPORT_SYMBOL_GPL(tracing_snapshot_cond_disable);
+#define free_snapshot(tr)	do { } while (0)
 #endif /* CONFIG_TRACER_SNAPSHOT */
 
 void tracer_tracing_off(struct trace_array *tr)
@@ -1492,10 +1489,12 @@
 	if (!str)
 		return 0;
 	buf_size = memparse(str, &str);
-	/* nr_entries can not be zero */
-	if (buf_size == 0)
-		return 0;
-	trace_buf_size = buf_size;
+	/*
+	 * nr_entries can not be zero and the startup
+	 * tests require some buffer space. Therefore
+	 * ensure we have at least 4096 bytes of buffer.
+	 */
+	trace_buf_size = max(4096UL, buf_size);
 	return 1;
 }
 __setup("trace_buf_size=", set_buf_size);
@@ -1689,6 +1688,8 @@
 }
 
 unsigned long __read_mostly	tracing_thresh;
+
+#ifdef CONFIG_TRACER_MAX_TRACE
 static const struct file_operations tracing_max_lat_fops;
 
 #ifdef LATENCY_FS_NOTIFY
@@ -1714,8 +1715,9 @@
 {
 	INIT_WORK(&tr->fsnotify_work, latency_fsnotify_workfn);
 	init_irq_work(&tr->fsnotify_irqwork, latency_fsnotify_workfn_irq);
-	tr->d_max_latency = trace_create_file("tracing_max_latency", 0644,
-					      d_tracer, &tr->max_latency,
+	tr->d_max_latency = trace_create_file("tracing_max_latency",
+					      TRACE_MODE_WRITE,
+					      d_tracer, tr,
 					      &tracing_max_lat_fops);
 }
 
@@ -1744,18 +1746,14 @@
 	irq_work_queue(&tr->fsnotify_irqwork);
 }
 
-#elif defined(CONFIG_TRACER_MAX_TRACE) || defined(CONFIG_HWLAT_TRACER)	\
-	|| defined(CONFIG_OSNOISE_TRACER)
+#else /* !LATENCY_FS_NOTIFY */
 
 #define trace_create_maxlat_file(tr, d_tracer)				\
-	trace_create_file("tracing_max_latency", 0644, d_tracer,	\
-			  &tr->max_latency, &tracing_max_lat_fops)
+	trace_create_file("tracing_max_latency", TRACE_MODE_WRITE,	\
+			  d_tracer, tr, &tracing_max_lat_fops)
 
-#else
-#define trace_create_maxlat_file(tr, d_tracer)	 do { } while (0)
 #endif
 
-#ifdef CONFIG_TRACER_MAX_TRACE
 /*
  * Copy the new maximum trace into the separate maximum-trace
  * structure. (this way the maximum trace is permanently saved,
@@ -1830,15 +1828,19 @@
 		ring_buffer_record_off(tr->max_buffer.buffer);
 
 #ifdef CONFIG_TRACER_SNAPSHOT
-	if (tr->cond_snapshot && !tr->cond_snapshot->update(tr, cond_data))
-		goto out_unlock;
+	if (tr->cond_snapshot && !tr->cond_snapshot->update(tr, cond_data)) {
+		arch_spin_unlock(&tr->max_lock);
+		return;
+	}
 #endif
 	swap(tr->array_buffer.buffer, tr->max_buffer.buffer);
 
 	__update_max_tr(tr, tsk, cpu);
 
- out_unlock:
 	arch_spin_unlock(&tr->max_lock);
+
+	/* Any waiters on the old snapshot buffer need to wake up */
+	ring_buffer_wake_waiters(tr->array_buffer.buffer, RING_BUFFER_ALL_CPUS);
 }
 
 /**
@@ -1874,9 +1876,10 @@
 		 * place on this CPU. We fail to record, but we reset
 		 * the max trace buffer (no one writes directly to it)
 		 * and flag that it failed.
+		 * Another reason is resize is in progress.
 		 */
 		trace_array_printk_buf(tr->max_buffer.buffer, _THIS_IP_,
-			"Failed to swap buffers due to commit in progress\n");
+			"Failed to swap buffers due to commit or resize in progress\n");
 	}
 
 	WARN_ON_ONCE(ret && ret != -EAGAIN && ret != -EBUSY);
@@ -1884,16 +1887,28 @@
 	__update_max_tr(tr, tsk, cpu);
 	arch_spin_unlock(&tr->max_lock);
 }
+
 #endif /* CONFIG_TRACER_MAX_TRACE */
 
 static int wait_on_pipe(struct trace_iterator *iter, int full)
 {
+	int ret;
+
 	/* Iterators are static, they should be filled or empty */
 	if (trace_buffer_iter(iter, iter->cpu_file))
 		return 0;
 
-	return ring_buffer_wait(iter->array_buffer->buffer, iter->cpu_file,
-				full);
+	ret = ring_buffer_wait(iter->array_buffer->buffer, iter->cpu_file, full);
+
+#ifdef CONFIG_TRACER_MAX_TRACE
+	/*
+	 * Make sure this is still the snapshot buffer, as if a snapshot were
+	 * to happen, this would now be the main buffer.
+	 */
+	if (iter->snapshot)
+		iter->array_buffer = &iter->tr->max_buffer;
+#endif
+	return ret;
 }
 
 #ifdef CONFIG_FTRACE_STARTUP_TEST
@@ -2176,10 +2191,12 @@
 }
 
 /* Must have trace_types_lock held */
-void tracing_reset_all_online_cpus(void)
+void tracing_reset_all_online_cpus_unlocked(void)
 {
 	struct trace_array *tr;
 
+	lockdep_assert_held(&trace_types_lock);
+
 	list_for_each_entry(tr, &ftrace_trace_arrays, list) {
 		if (!tr->clear_trace)
 			continue;
@@ -2191,6 +2208,13 @@
 	}
 }
 
+void tracing_reset_all_online_cpus(void)
+{
+	mutex_lock(&trace_types_lock);
+	tracing_reset_all_online_cpus_unlocked();
+	mutex_unlock(&trace_types_lock);
+}
+
 /*
  * The tgid_map array maps from pid to tgid; i.e. the value stored at index i
  * is the tgid last observed corresponding to pid=i.
@@ -2202,16 +2226,25 @@
 
 #define SAVED_CMDLINES_DEFAULT 128
 #define NO_CMDLINE_MAP UINT_MAX
+/*
+ * Preemption must be disabled before acquiring trace_cmdline_lock.
+ * The various trace_arrays' max_lock must be acquired in a context
+ * where interrupt is disabled.
+ */
 static arch_spinlock_t trace_cmdline_lock = __ARCH_SPIN_LOCK_UNLOCKED;
 struct saved_cmdlines_buffer {
 	unsigned map_pid_to_cmdline[PID_MAX_DEFAULT+1];
 	unsigned *map_cmdline_to_pid;
 	unsigned cmdline_num;
 	int cmdline_idx;
-	char *saved_cmdlines;
+	char saved_cmdlines[];
 };
 static struct saved_cmdlines_buffer *savedcmd;
 
+/* Holds the size of a cmdline and pid element */
+#define SAVED_CMDLINE_MAP_ELEMENT_SIZE(s)			\
+	(TASK_COMM_LEN + sizeof((s)->map_cmdline_to_pid[0]))
+
 static inline char *get_saved_cmdlines(int idx)
 {
 	return &savedcmd->saved_cmdlines[idx * TASK_COMM_LEN];
@@ -2222,47 +2255,54 @@
 	strncpy(get_saved_cmdlines(idx), cmdline, TASK_COMM_LEN);
 }
 
-static int allocate_cmdlines_buffer(unsigned int val,
-				    struct saved_cmdlines_buffer *s)
+static void free_saved_cmdlines_buffer(struct saved_cmdlines_buffer *s)
 {
-	s->map_cmdline_to_pid = kmalloc_array(val,
-					      sizeof(*s->map_cmdline_to_pid),
-					      GFP_KERNEL);
-	if (!s->map_cmdline_to_pid)
-		return -ENOMEM;
+	int order = get_order(sizeof(*s) + s->cmdline_num * TASK_COMM_LEN);
 
-	s->saved_cmdlines = kmalloc_array(TASK_COMM_LEN, val, GFP_KERNEL);
-	if (!s->saved_cmdlines) {
-		kfree(s->map_cmdline_to_pid);
-		return -ENOMEM;
-	}
+	kmemleak_free(s);
+	free_pages((unsigned long)s, order);
+}
 
-	s->cmdline_idx = 0;
+static struct saved_cmdlines_buffer *allocate_cmdlines_buffer(unsigned int val)
+{
+	struct saved_cmdlines_buffer *s;
+	struct page *page;
+	int orig_size, size;
+	int order;
+
+	/* Figure out how much is needed to hold the given number of cmdlines */
+	orig_size = sizeof(*s) + val * SAVED_CMDLINE_MAP_ELEMENT_SIZE(s);
+	order = get_order(orig_size);
+	size = 1 << (order + PAGE_SHIFT);
+	page = alloc_pages(GFP_KERNEL, order);
+	if (!page)
+		return NULL;
+
+	s = page_address(page);
+	kmemleak_alloc(s, size, 1, GFP_KERNEL);
+	memset(s, 0, sizeof(*s));
+
+	/* Round up to actual allocation */
+	val = (size - sizeof(*s)) / SAVED_CMDLINE_MAP_ELEMENT_SIZE(s);
 	s->cmdline_num = val;
+
+	/* Place map_cmdline_to_pid array right after saved_cmdlines */
+	s->map_cmdline_to_pid = (unsigned *)&s->saved_cmdlines[val * TASK_COMM_LEN];
+
+	s->cmdline_idx = 0;
 	memset(&s->map_pid_to_cmdline, NO_CMDLINE_MAP,
 	       sizeof(s->map_pid_to_cmdline));
 	memset(s->map_cmdline_to_pid, NO_CMDLINE_MAP,
 	       val * sizeof(*s->map_cmdline_to_pid));
 
-	return 0;
+	return s;
 }
 
 static int trace_create_savedcmd(void)
 {
-	int ret;
-
-	savedcmd = kmalloc(sizeof(*savedcmd), GFP_KERNEL);
-	if (!savedcmd)
-		return -ENOMEM;
-
-	ret = allocate_cmdlines_buffer(SAVED_CMDLINES_DEFAULT, savedcmd);
-	if (ret < 0) {
-		kfree(savedcmd);
-		savedcmd = NULL;
-		return -ENOMEM;
-	}
+	savedcmd = allocate_cmdlines_buffer(SAVED_CMDLINES_DEFAULT);
 
-	return 0;
+	return savedcmd ? 0 : -ENOMEM;
 }
 
 int is_tracing_stopped(void)
@@ -2270,13 +2310,7 @@
 	return global_trace.stop_count;
 }
 
-/**
- * tracing_start - quick start of the tracer
- *
- * If tracing is enabled but was stopped by tracing_stop,
- * this will start the tracer back up.
- */
-void tracing_start(void)
+static void tracing_start_tr(struct trace_array *tr)
 {
 	struct trace_buffer *buffer;
 	unsigned long flags;
@@ -2284,119 +2318,83 @@
 	if (tracing_disabled)
 		return;
 
-	raw_spin_lock_irqsave(&global_trace.start_lock, flags);
-	if (--global_trace.stop_count) {
-		if (global_trace.stop_count < 0) {
+	raw_spin_lock_irqsave(&tr->start_lock, flags);
+	if (--tr->stop_count) {
+		if (WARN_ON_ONCE(tr->stop_count < 0)) {
 			/* Someone screwed up their debugging */
-			WARN_ON_ONCE(1);
-			global_trace.stop_count = 0;
+			tr->stop_count = 0;
 		}
 		goto out;
 	}
 
 	/* Prevent the buffers from switching */
-	arch_spin_lock(&global_trace.max_lock);
+	arch_spin_lock(&tr->max_lock);
 
-	buffer = global_trace.array_buffer.buffer;
+	buffer = tr->array_buffer.buffer;
 	if (buffer)
 		ring_buffer_record_enable(buffer);
 
 #ifdef CONFIG_TRACER_MAX_TRACE
-	buffer = global_trace.max_buffer.buffer;
+	buffer = tr->max_buffer.buffer;
 	if (buffer)
 		ring_buffer_record_enable(buffer);
 #endif
 
-	arch_spin_unlock(&global_trace.max_lock);
-
- out:
-	raw_spin_unlock_irqrestore(&global_trace.start_lock, flags);
-}
-
-static void tracing_start_tr(struct trace_array *tr)
-{
-	struct trace_buffer *buffer;
-	unsigned long flags;
-
-	if (tracing_disabled)
-		return;
-
-	/* If global, we need to also start the max tracer */
-	if (tr->flags & TRACE_ARRAY_FL_GLOBAL)
-		return tracing_start();
-
-	raw_spin_lock_irqsave(&tr->start_lock, flags);
-
-	if (--tr->stop_count) {
-		if (tr->stop_count < 0) {
-			/* Someone screwed up their debugging */
-			WARN_ON_ONCE(1);
-			tr->stop_count = 0;
-		}
-		goto out;
-	}
-
-	buffer = tr->array_buffer.buffer;
-	if (buffer)
-		ring_buffer_record_enable(buffer);
+	arch_spin_unlock(&tr->max_lock);
 
  out:
 	raw_spin_unlock_irqrestore(&tr->start_lock, flags);
 }
 
 /**
- * tracing_stop - quick stop of the tracer
+ * tracing_start - quick start of the tracer
  *
- * Light weight way to stop tracing. Use in conjunction with
- * tracing_start.
+ * If tracing is enabled but was stopped by tracing_stop,
+ * this will start the tracer back up.
  */
-void tracing_stop(void)
+void tracing_start(void)
+
+{
+	return tracing_start_tr(&global_trace);
+}
+
+static void tracing_stop_tr(struct trace_array *tr)
 {
 	struct trace_buffer *buffer;
 	unsigned long flags;
 
-	raw_spin_lock_irqsave(&global_trace.start_lock, flags);
-	if (global_trace.stop_count++)
+	raw_spin_lock_irqsave(&tr->start_lock, flags);
+	if (tr->stop_count++)
 		goto out;
 
 	/* Prevent the buffers from switching */
-	arch_spin_lock(&global_trace.max_lock);
+	arch_spin_lock(&tr->max_lock);
 
-	buffer = global_trace.array_buffer.buffer;
+	buffer = tr->array_buffer.buffer;
 	if (buffer)
 		ring_buffer_record_disable(buffer);
 
 #ifdef CONFIG_TRACER_MAX_TRACE
-	buffer = global_trace.max_buffer.buffer;
+	buffer = tr->max_buffer.buffer;
 	if (buffer)
 		ring_buffer_record_disable(buffer);
 #endif
 
-	arch_spin_unlock(&global_trace.max_lock);
+	arch_spin_unlock(&tr->max_lock);
 
  out:
-	raw_spin_unlock_irqrestore(&global_trace.start_lock, flags);
+	raw_spin_unlock_irqrestore(&tr->start_lock, flags);
 }
 
-static void tracing_stop_tr(struct trace_array *tr)
+/**
+ * tracing_stop - quick stop of the tracer
+ *
+ * Light weight way to stop tracing. Use in conjunction with
+ * tracing_start.
+ */
+void tracing_stop(void)
 {
-	struct trace_buffer *buffer;
-	unsigned long flags;
-
-	/* If global, we need to also stop the max tracer */
-	if (tr->flags & TRACE_ARRAY_FL_GLOBAL)
-		return tracing_stop();
-
-	raw_spin_lock_irqsave(&tr->start_lock, flags);
-	if (tr->stop_count++)
-		goto out;
-
-	buffer = tr->array_buffer.buffer;
-	if (buffer)
-		ring_buffer_record_disable(buffer);
-
- out:
-	raw_spin_unlock_irqrestore(&tr->start_lock, flags);
+	return tracing_stop_tr(&global_trace);
 }
 
 static int trace_save_cmdline(struct task_struct *tsk)
@@ -2414,7 +2412,11 @@
 	 * the lock, but we also don't want to spin
 	 * nor do we want to disable interrupts,
 	 * so if we miss here, then better luck next time.
+	 *
+	 * This is called within the scheduler and wake up, so interrupts
+	 * had better been disabled and run queue lock been held.
 	 */
+	lockdep_assert_preemption_disabled();
 	if (!arch_spin_trylock(&trace_cmdline_lock))
 		return 0;
 
@@ -2674,8 +2676,11 @@
 	for_each_tracing_cpu(cpu) {
 		page = alloc_pages_node(cpu_to_node(cpu),
 					GFP_KERNEL | __GFP_NORETRY, 0);
-		if (!page)
-			goto failed;
+		/* This is just an optimization and can handle failures */
+		if (!page) {
+			pr_err("Failed to allocate event buffer\n");
+			break;
+		}
 
 		event = page_address(page);
 		memset(event, 0, sizeof(*event));
@@ -2689,10 +2694,6 @@
 			WARN_ON_ONCE(1);
 		preempt_enable();
 	}
-
-	return;
- failed:
-	trace_buffered_event_disable();
 }
 
 static void enable_trace_buffered_event(void *data)
@@ -2727,11 +2728,9 @@
 	if (--trace_buffered_event_ref)
 		return;
 
-	preempt_disable();
 	/* For each CPU, set the buffer as used. */
-	smp_call_function_many(tracing_buffer_mask,
-			       disable_trace_buffered_event, NULL, 1);
-	preempt_enable();
+	on_each_cpu_mask(tracing_buffer_mask, disable_trace_buffered_event,
+			 NULL, true);
 
 	/* Wait for all current users to finish */
 	synchronize_rcu();
@@ -2740,17 +2739,19 @@
 		free_page((unsigned long)per_cpu(trace_buffered_event, cpu));
 		per_cpu(trace_buffered_event, cpu) = NULL;
 	}
+
 	/*
-	 * Make sure trace_buffered_event is NULL before clearing
-	 * trace_buffered_event_cnt.
+	 * Wait for all CPUs that potentially started checking if they can use
+	 * their event buffer only after the previous synchronize_rcu() call and
+	 * they still read a valid pointer from trace_buffered_event. It must be
+	 * ensured they don't see cleared trace_buffered_event_cnt else they
+	 * could wrongly decide to use the pointed-to buffer which is now freed.
 	 */
-	smp_wmb();
+	synchronize_rcu();
 
-	preempt_disable();
-	/* Do the work on each cpu */
-	smp_call_function_many(tracing_buffer_mask,
-			       enable_trace_buffered_event, NULL, 1);
-	preempt_enable();
+	/* For each CPU, relinquish the buffer */
+	on_each_cpu_mask(tracing_buffer_mask, enable_trace_buffered_event, NULL,
+			 true);
 }
 
 static struct trace_buffer *temp_buffer;
@@ -2833,7 +2834,7 @@
 }
 EXPORT_SYMBOL_GPL(trace_event_buffer_lock_reserve);
 
-static DEFINE_SPINLOCK(tracepoint_iter_lock);
+static DEFINE_RAW_SPINLOCK(tracepoint_iter_lock);
 static DEFINE_MUTEX(tracepoint_printk_mutex);
 
 static void output_printk(struct trace_event_buffer *fbuffer)
@@ -2861,14 +2862,14 @@
 
 	event = &fbuffer->trace_file->event_call->event;
 
-	spin_lock_irqsave(&tracepoint_iter_lock, flags);
+	raw_spin_lock_irqsave(&tracepoint_iter_lock, flags);
 	trace_seq_init(&iter->seq);
 	iter->ent = fbuffer->entry;
 	event_call->event.funcs->trace(iter, 0, event);
 	trace_seq_putc(&iter->seq, 0);
 	printk("%s", iter->seq.buffer);
 
-	spin_unlock_irqrestore(&tracepoint_iter_lock, flags);
+	raw_spin_unlock_irqrestore(&tracepoint_iter_lock, flags);
 }
 
 int tracepoint_printk_sysctl(struct ctl_table *table, int write,
@@ -3230,7 +3231,7 @@
 	char buffer[4][TRACE_BUF_SIZE];
 };
 
-static struct trace_buffer_struct *trace_percpu_buffer;
+static struct trace_buffer_struct __percpu *trace_percpu_buffer;
 
 /*
  * This allows for lockless recording.  If we're nested too deeply, then
@@ -3240,7 +3241,7 @@
 {
 	struct trace_buffer_struct *buffer = this_cpu_ptr(trace_percpu_buffer);
 
-	if (!buffer || buffer->nesting >= 4)
+	if (!trace_percpu_buffer || buffer->nesting >= 4)
 		return NULL;
 
 	buffer->nesting++;
@@ -3259,7 +3260,7 @@
 
 static int alloc_percpu_trace_buffer(void)
 {
-	struct trace_buffer_struct *buffers;
+	struct trace_buffer_struct __percpu *buffers;
 
 	if (trace_percpu_buffer)
 		return 0;
@@ -3671,12 +3672,17 @@
 }
 
 /* Returns true if the string is safe to dereference from an event */
-static bool trace_safe_str(struct trace_iterator *iter, const char *str)
+static bool trace_safe_str(struct trace_iterator *iter, const char *str,
+			   bool star, int len)
 {
 	unsigned long addr = (unsigned long)str;
 	struct trace_event *trace_event;
 	struct trace_event_call *event;
 
+	/* Ignore strings with no length */
+	if (star && !len)
+		return true;
+
 	/* OK if part of the event data */
 	if ((addr >= (unsigned long)iter->ent) &&
 	    (addr < (unsigned long)iter->ent + iter->ent_size))
@@ -3835,6 +3841,18 @@
 		iter->fmt[i] = '\0';
 		trace_seq_vprintf(&iter->seq, iter->fmt, ap);
 
+		/*
+		 * If iter->seq is full, the above call no longer guarantees
+		 * that ap is in sync with fmt processing, and further calls
+		 * to va_arg() can return wrong positional arguments.
+		 *
+		 * Ensure that ap is no longer used in this case.
+		 */
+		if (iter->seq.full) {
+			p = "";
+			break;
+		}
+
 		if (star)
 			len = va_arg(ap, int);
 
@@ -3850,7 +3868,7 @@
 		 * instead. See samples/trace_events/trace-events-sample.h
 		 * for reference.
 		 */
-		if (WARN_ONCE(!trace_safe_str(iter, str),
+		if (WARN_ONCE(!trace_safe_str(iter, str, star, len),
 			      "fmt: '%s' current_buffer: '%s'",
 			      fmt, show_buffer(&iter->seq))) {
 			int ret;
@@ -4048,6 +4066,8 @@
 			break;
 		entries++;
 		ring_buffer_iter_advance(buf_iter);
+		/* This could be a big loop */
+		cond_resched();
 	}
 
 	per_cpu_ptr(iter->array_buffer->data, cpu)->skipped_entries = entries;
@@ -4073,8 +4093,15 @@
 	 * will point to the same string as current_trace->name.
 	 */
 	mutex_lock(&trace_types_lock);
-	if (unlikely(tr->current_trace && iter->trace->name != tr->current_trace->name))
+	if (unlikely(tr->current_trace && iter->trace->name != tr->current_trace->name)) {
+		/* Close iter->trace before switching to the new current tracer */
+		if (iter->trace->close)
+			iter->trace->close(iter);
 		*iter->trace = *tr->current_trace;
+		/* Reopen the new current tracer */
+		if (iter->trace->open)
+			iter->trace->open(iter);
+	}
 	mutex_unlock(&trace_types_lock);
 
 #ifdef CONFIG_TRACER_MAX_TRACE
@@ -4654,7 +4681,11 @@
 		iter->leftover = ret;
 
 	} else {
-		print_trace_line(iter);
+		ret = print_trace_line(iter);
+		if (ret == TRACE_TYPE_PARTIAL_LINE) {
+			iter->seq.full = 0;
+			trace_seq_puts(&iter->seq, "[LINE TOO BIG]\n");
+		}
 		ret = trace_print_seq(m, &iter->seq);
 		/*
 		 * If we overflow the seq_file buffer, then it will
@@ -4845,6 +4876,60 @@
 	return 0;
 }
 
+/*
+ * The private pointer of the inode is the trace_event_file.
+ * Update the tr ref count associated to it.
+ */
+int tracing_open_file_tr(struct inode *inode, struct file *filp)
+{
+	struct trace_event_file *file = inode->i_private;
+	int ret;
+
+	ret = tracing_check_open_get_tr(file->tr);
+	if (ret)
+		return ret;
+
+	mutex_lock(&event_mutex);
+
+	/* Fail if the file is marked for removal */
+	if (file->flags & EVENT_FILE_FL_FREED) {
+		trace_array_put(file->tr);
+		ret = -ENODEV;
+	} else {
+		event_file_get(file);
+	}
+
+	mutex_unlock(&event_mutex);
+	if (ret)
+		return ret;
+
+	filp->private_data = inode->i_private;
+
+	return 0;
+}
+
+int tracing_release_file_tr(struct inode *inode, struct file *filp)
+{
+	struct trace_event_file *file = inode->i_private;
+
+	trace_array_put(file->tr);
+	event_file_put(file);
+
+	return 0;
+}
+
+int tracing_single_release_file_tr(struct inode *inode, struct file *filp)
+{
+	tracing_release_file_tr(inode, filp);
+	return single_release(inode, filp);
+}
+
+static int tracing_mark_open(struct inode *inode, struct file *filp)
+{
+	stream_open(inode, filp);
+	return tracing_open_generic_tr(inode, filp);
+}
+
 static int tracing_release(struct inode *inode, struct file *file)
 {
 	struct trace_array *tr = inode->i_private;
@@ -5075,6 +5160,8 @@
 static const struct file_operations tracing_fops = {
 	.open		= tracing_open,
 	.read		= seq_read,
+	.read_iter	= seq_read_iter,
+	.splice_read	= generic_file_splice_read,
 	.write		= tracing_write_stub,
 	.llseek		= tracing_lseek,
 	.release	= tracing_release,
@@ -5134,11 +5221,17 @@
 				!cpumask_test_cpu(cpu, tracing_cpumask_new)) {
 			atomic_inc(&per_cpu_ptr(tr->array_buffer.data, cpu)->disabled);
 			ring_buffer_record_disable_cpu(tr->array_buffer.buffer, cpu);
+#ifdef CONFIG_TRACER_MAX_TRACE
+			ring_buffer_record_disable_cpu(tr->max_buffer.buffer, cpu);
+#endif
 		}
 		if (!cpumask_test_cpu(cpu, tr->tracing_cpumask) &&
 				cpumask_test_cpu(cpu, tracing_cpumask_new)) {
 			atomic_dec(&per_cpu_ptr(tr->array_buffer.data, cpu)->disabled);
 			ring_buffer_record_enable_cpu(tr->array_buffer.buffer, cpu);
+#ifdef CONFIG_TRACER_MAX_TRACE
+			ring_buffer_record_enable_cpu(tr->max_buffer.buffer, cpu);
+#endif
 		}
 	}
 	arch_spin_unlock(&tr->max_lock);
@@ -5157,6 +5250,9 @@
 	cpumask_var_t tracing_cpumask_new;
 	int err;
 
+	if (count == 0 || count > KMALLOC_MAX_SIZE)
+		return -EINVAL;
+
 	if (!zalloc_cpumask_var(&tracing_cpumask_new, GFP_KERNEL))
 		return -ENOMEM;
 
@@ -5573,7 +5669,7 @@
 	"\t           +|-[u]<offset>(<fetcharg>), \\imm-value, \\\"imm-string\"\n"
 	"\t     type: s8/16/32/64, u8/16/32/64, x8/16/32/64, string, symbol,\n"
 	"\t           b<bit-width>@<bit-offset>/<container-size>, ustring,\n"
-	"\t           <type>\\[<array-size>\\]\n"
+	"\t           symstr, <type>\\[<array-size>\\]\n"
 #ifdef CONFIG_HIST_TRIGGERS
 	"\t    field: <stype> <name>;\n"
 	"\t    stype: u8/u16/u32/u64, s8/s16/s32/s64, pid_t,\n"
@@ -5859,37 +5955,29 @@
 	char buf[64];
 	int r;
 
+	preempt_disable();
 	arch_spin_lock(&trace_cmdline_lock);
 	r = scnprintf(buf, sizeof(buf), "%u\n", savedcmd->cmdline_num);
 	arch_spin_unlock(&trace_cmdline_lock);
+	preempt_enable();
 
 	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
 }
 
-static void free_saved_cmdlines_buffer(struct saved_cmdlines_buffer *s)
-{
-	kfree(s->saved_cmdlines);
-	kfree(s->map_cmdline_to_pid);
-	kfree(s);
-}
-
 static int tracing_resize_saved_cmdlines(unsigned int val)
 {
 	struct saved_cmdlines_buffer *s, *savedcmd_temp;
 
-	s = kmalloc(sizeof(*s), GFP_KERNEL);
+	s = allocate_cmdlines_buffer(val);
 	if (!s)
 		return -ENOMEM;
 
-	if (allocate_cmdlines_buffer(val, s) < 0) {
-		kfree(s);
-		return -ENOMEM;
-	}
-
+	preempt_disable();
 	arch_spin_lock(&trace_cmdline_lock);
 	savedcmd_temp = savedcmd;
 	savedcmd = s;
 	arch_spin_unlock(&trace_cmdline_lock);
+	preempt_enable();
 	free_saved_cmdlines_buffer(savedcmd_temp);
 
 	return 0;
@@ -6077,7 +6165,7 @@
 
 static void trace_create_eval_file(struct dentry *d_tracer)
 {
-	trace_create_file("eval_map", 0444, d_tracer,
+	trace_create_file("eval_map", TRACE_MODE_READ, d_tracer,
 			  NULL, &tracing_eval_map_fops);
 }
 
@@ -6131,6 +6219,15 @@
 		per_cpu_ptr(buf->data, cpu)->entries = val;
 }
 
+static void update_buffer_entries(struct array_buffer *buf, int cpu)
+{
+	if (cpu == RING_BUFFER_ALL_CPUS) {
+		set_buffer_entries(buf, ring_buffer_size(buf->buffer, 0));
+	} else {
+		per_cpu_ptr(buf->data, cpu)->entries = ring_buffer_size(buf->buffer, cpu);
+	}
+}
+
 #ifdef CONFIG_TRACER_MAX_TRACE
 /* resize @tr's buffer to the size of @size_tr's entries */
 static int resize_buffer_duplicate_size(struct array_buffer *trace_buf,
@@ -6175,13 +6272,15 @@
 	if (!tr->array_buffer.buffer)
 		return 0;
 
+	/* Do not allow tracing while resizing ring buffer */
+	tracing_stop_tr(tr);
+
 	ret = ring_buffer_resize(tr->array_buffer.buffer, size, cpu);
 	if (ret < 0)
-		return ret;
+		goto out_start;
 
 #ifdef CONFIG_TRACER_MAX_TRACE
-	if (!(tr->flags & TRACE_ARRAY_FL_GLOBAL) ||
-	    !tr->current_trace->use_max_tr)
+	if (!tr->allocated_snapshot)
 		goto out;
 
 	ret = ring_buffer_resize(tr->max_buffer.buffer, size, cpu);
@@ -6206,22 +6305,17 @@
 			WARN_ON(1);
 			tracing_disabled = 1;
 		}
-		return ret;
+		goto out_start;
 	}
 
-	if (cpu == RING_BUFFER_ALL_CPUS)
-		set_buffer_entries(&tr->max_buffer, size);
-	else
-		per_cpu_ptr(tr->max_buffer.data, cpu)->entries = size;
+	update_buffer_entries(&tr->max_buffer, cpu);
 
  out:
 #endif /* CONFIG_TRACER_MAX_TRACE */
 
-	if (cpu == RING_BUFFER_ALL_CPUS)
-		set_buffer_entries(&tr->array_buffer, size);
-	else
-		per_cpu_ptr(tr->array_buffer.data, cpu)->entries = size;
-
+	update_buffer_entries(&tr->array_buffer, cpu);
+ out_start:
+	tracing_start_tr(tr);
 	return ret;
 }
 
@@ -6296,12 +6390,18 @@
 	tr->current_trace = &nop_trace;
 }
 
+static bool tracer_options_updated;
+
 static void add_tracer_options(struct trace_array *tr, struct tracer *t)
 {
 	/* Only enable if the directory has been created already. */
 	if (!tr->dir)
 		return;
 
+	/* Only create trace option files after update_tracer_options finish */
+	if (!tracer_options_updated)
+		return;
+
 	create_trace_option_files(tr, t);
 }
 
@@ -6336,10 +6436,12 @@
 
 #ifdef CONFIG_TRACER_SNAPSHOT
 	if (t->use_max_tr) {
+		local_irq_disable();
 		arch_spin_lock(&tr->max_lock);
 		if (tr->cond_snapshot)
 			ret = -EBUSY;
 		arch_spin_unlock(&tr->max_lock);
+		local_irq_enable();
 		if (ret)
 			goto out;
 	}
@@ -6370,12 +6472,12 @@
 	if (tr->current_trace->reset)
 		tr->current_trace->reset(tr);
 
+#ifdef CONFIG_TRACER_MAX_TRACE
+	had_max_tr = tr->current_trace->use_max_tr;
+
 	/* Current trace needs to be nop_trace before synchronize_rcu */
 	tr->current_trace = &nop_trace;
 
-#ifdef CONFIG_TRACER_MAX_TRACE
-	had_max_tr = tr->allocated_snapshot;
-
 	if (had_max_tr && !t->use_max_tr) {
 		/*
 		 * We need to make sure that the update_max_tr sees that
@@ -6387,14 +6489,14 @@
 		synchronize_rcu();
 		free_snapshot(tr);
 	}
-#endif
 
-#ifdef CONFIG_TRACER_MAX_TRACE
-	if (t->use_max_tr && !had_max_tr) {
+	if (t->use_max_tr && !tr->allocated_snapshot) {
 		ret = tracing_alloc_snapshot_instance(tr);
 		if (ret < 0)
 			goto out;
 	}
+#else
+	tr->current_trace = &nop_trace;
 #endif
 
 	if (t->init) {
@@ -6507,28 +6609,58 @@
 	return ret;
 }
 
-#if defined(CONFIG_TRACER_MAX_TRACE) || defined(CONFIG_HWLAT_TRACER)
+#ifdef CONFIG_TRACER_MAX_TRACE
 
 static ssize_t
 tracing_max_lat_read(struct file *filp, char __user *ubuf,
 		     size_t cnt, loff_t *ppos)
 {
-	return tracing_nsecs_read(filp->private_data, ubuf, cnt, ppos);
+	struct trace_array *tr = filp->private_data;
+
+	return tracing_nsecs_read(&tr->max_latency, ubuf, cnt, ppos);
 }
 
 static ssize_t
 tracing_max_lat_write(struct file *filp, const char __user *ubuf,
 		      size_t cnt, loff_t *ppos)
 {
-	return tracing_nsecs_write(filp->private_data, ubuf, cnt, ppos);
+	struct trace_array *tr = filp->private_data;
+
+	return tracing_nsecs_write(&tr->max_latency, ubuf, cnt, ppos);
 }
 
 #endif
 
+static int open_pipe_on_cpu(struct trace_array *tr, int cpu)
+{
+	if (cpu == RING_BUFFER_ALL_CPUS) {
+		if (cpumask_empty(tr->pipe_cpumask)) {
+			cpumask_setall(tr->pipe_cpumask);
+			return 0;
+		}
+	} else if (!cpumask_test_cpu(cpu, tr->pipe_cpumask)) {
+		cpumask_set_cpu(cpu, tr->pipe_cpumask);
+		return 0;
+	}
+	return -EBUSY;
+}
+
+static void close_pipe_on_cpu(struct trace_array *tr, int cpu)
+{
+	if (cpu == RING_BUFFER_ALL_CPUS) {
+		WARN_ON(!cpumask_full(tr->pipe_cpumask));
+		cpumask_clear(tr->pipe_cpumask);
+	} else {
+		WARN_ON(!cpumask_test_cpu(cpu, tr->pipe_cpumask));
+		cpumask_clear_cpu(cpu, tr->pipe_cpumask);
+	}
+}
+
 static int tracing_open_pipe(struct inode *inode, struct file *filp)
 {
 	struct trace_array *tr = inode->i_private;
 	struct trace_iterator *iter;
+	int cpu;
 	int ret;
 
 	ret = tracing_check_open_get_tr(tr);
@@ -6536,13 +6668,16 @@
 		return ret;
 
 	mutex_lock(&trace_types_lock);
+	cpu = tracing_get_cpu(inode);
+	ret = open_pipe_on_cpu(tr, cpu);
+	if (ret)
+		goto fail_pipe_on_cpu;
 
 	/* create a buffer to store the information to pass to userspace */
 	iter = kzalloc(sizeof(*iter), GFP_KERNEL);
 	if (!iter) {
 		ret = -ENOMEM;
-		__trace_array_put(tr);
-		goto out;
+		goto fail_alloc_iter;
 	}
 
 	trace_seq_init(&iter->seq);
@@ -6565,7 +6700,7 @@
 
 	iter->tr = tr;
 	iter->array_buffer = &tr->array_buffer;
-	iter->cpu_file = tracing_get_cpu(inode);
+	iter->cpu_file = cpu;
 	mutex_init(&iter->mutex);
 	filp->private_data = iter;
 
@@ -6575,12 +6710,15 @@
 	nonseekable_open(inode, filp);
 
 	tr->trace_ref++;
-out:
+
 	mutex_unlock(&trace_types_lock);
 	return ret;
 
 fail:
 	kfree(iter);
+fail_alloc_iter:
+	close_pipe_on_cpu(tr, cpu);
+fail_pipe_on_cpu:
 	__trace_array_put(tr);
 	mutex_unlock(&trace_types_lock);
 	return ret;
@@ -6597,10 +6735,12 @@
 
 	if (iter->trace->pipe_close)
 		iter->trace->pipe_close(iter);
-
+	close_pipe_on_cpu(tr, iter->cpu_file);
 	mutex_unlock(&trace_types_lock);
 
 	free_cpumask_var(iter->started);
+	kfree(iter->fmt);
+	kfree(iter->temp);
 	mutex_destroy(&iter->mutex);
 	kfree(iter);
 
@@ -6625,7 +6765,7 @@
 		return EPOLLIN | EPOLLRDNORM;
 	else
 		return ring_buffer_poll_wait(iter->array_buffer->buffer, iter->cpu_file,
-					     filp, poll_table);
+					     filp, poll_table, iter->tr->buffer_percent);
 }
 
 static __poll_t
@@ -6733,7 +6873,20 @@
 
 		ret = print_trace_line(iter);
 		if (ret == TRACE_TYPE_PARTIAL_LINE) {
-			/* don't print partial lines */
+			/*
+			 * If one print_trace_line() fills entire trace_seq in one shot,
+			 * trace_seq_to_user() will returns -EBUSY because save_len == 0,
+			 * In this case, we need to consume it, otherwise, loop will peek
+			 * this event next time, resulting in an infinite loop.
+			 */
+			if (save_len == 0) {
+				iter->seq.full = 0;
+				trace_seq_puts(&iter->seq, "[LINE TOO BIG]\n");
+				trace_consume(iter);
+				break;
+			}
+
+			/* In other cases, don't print partial lines */
 			iter->seq.seq.len = save_len;
 			break;
 		}
@@ -7112,9 +7265,6 @@
 	if (tt)
 		event_triggers_post_call(tr->trace_marker_file, tt);
 
-	if (written > 0)
-		*fpos += written;
-
 	return written;
 }
 
@@ -7173,9 +7323,6 @@
 
 	__buffer_unlock_commit(buffer, event);
 
-	if (written > 0)
-		*fpos += written;
-
 	return written;
 }
 
@@ -7387,6 +7534,11 @@
 	return ret;
 }
 
+static void tracing_swap_cpu_buffer(void *tr)
+{
+	update_max_tr_single((struct trace_array *)tr, current, smp_processor_id());
+}
+
 static ssize_t
 tracing_snapshot_write(struct file *filp, const char __user *ubuf, size_t cnt,
 		       loff_t *ppos)
@@ -7412,10 +7564,12 @@
 		goto out;
 	}
 
+	local_irq_disable();
 	arch_spin_lock(&tr->max_lock);
 	if (tr->cond_snapshot)
 		ret = -EBUSY;
 	arch_spin_unlock(&tr->max_lock);
+	local_irq_enable();
 	if (ret)
 		goto out;
 
@@ -7443,13 +7597,15 @@
 			ret = tracing_alloc_snapshot_instance(tr);
 		if (ret < 0)
 			break;
-		local_irq_disable();
 		/* Now, we're going to swap */
-		if (iter->cpu_file == RING_BUFFER_ALL_CPUS)
+		if (iter->cpu_file == RING_BUFFER_ALL_CPUS) {
+			local_irq_disable();
 			update_max_tr(tr, current, smp_processor_id(), NULL);
-		else
-			update_max_tr_single(tr, current, iter->cpu_file);
-		local_irq_enable();
+			local_irq_enable();
+		} else {
+			smp_call_function_single(iter->cpu_file, tracing_swap_cpu_buffer,
+						 (void *)tr, 1);
+		}
 		break;
 	default:
 		if (tr->allocated_snapshot) {
@@ -7528,20 +7684,22 @@
 	.llseek		= generic_file_llseek,
 };
 
-#if defined(CONFIG_TRACER_MAX_TRACE) || defined(CONFIG_HWLAT_TRACER)
+#ifdef CONFIG_TRACER_MAX_TRACE
 static const struct file_operations tracing_max_lat_fops = {
-	.open		= tracing_open_generic,
+	.open		= tracing_open_generic_tr,
 	.read		= tracing_max_lat_read,
 	.write		= tracing_max_lat_write,
 	.llseek		= generic_file_llseek,
+	.release	= tracing_release_generic_tr,
 };
 #endif
 
 static const struct file_operations set_tracer_fops = {
-	.open		= tracing_open_generic,
+	.open		= tracing_open_generic_tr,
 	.read		= tracing_set_trace_read,
 	.write		= tracing_set_trace_write,
 	.llseek		= generic_file_llseek,
+	.release	= tracing_release_generic_tr,
 };
 
 static const struct file_operations tracing_pipe_fops = {
@@ -7575,16 +7733,14 @@
 };
 
 static const struct file_operations tracing_mark_fops = {
-	.open		= tracing_open_generic_tr,
+	.open		= tracing_mark_open,
 	.write		= tracing_mark_write,
-	.llseek		= generic_file_llseek,
 	.release	= tracing_release_generic_tr,
 };
 
 static const struct file_operations tracing_mark_raw_fops = {
-	.open		= tracing_open_generic_tr,
+	.open		= tracing_mark_open,
 	.write		= tracing_mark_raw_write,
-	.llseek		= generic_file_llseek,
 	.release	= tracing_release_generic_tr,
 };
 
@@ -7736,7 +7892,8 @@
 		err = kzalloc(sizeof(*err), GFP_KERNEL);
 		if (!err)
 			err = ERR_PTR(-ENOMEM);
-		tr->n_err_log_entries++;
+		else
+			tr->n_err_log_entries++;
 
 		return err;
 	}
@@ -7948,7 +8105,7 @@
 	.open           = tracing_err_log_open,
 	.write		= tracing_err_log_write,
 	.read           = seq_read,
-	.llseek         = seq_lseek,
+	.llseek         = tracing_lseek,
 	.release        = tracing_err_log_release,
 };
 
@@ -8074,6 +8231,20 @@
 	return size;
 }
 
+static int tracing_buffers_flush(struct file *file, fl_owner_t id)
+{
+	struct ftrace_buffer_info *info = file->private_data;
+	struct trace_iterator *iter = &info->iter;
+
+	iter->wait_index++;
+	/* Make sure the waiters see the new wait_index */
+	smp_wmb();
+
+	ring_buffer_wake_waiters(iter->array_buffer->buffer, iter->cpu_file);
+
+	return 0;
+}
+
 static int tracing_buffers_release(struct inode *inode, struct file *file)
 {
 	struct ftrace_buffer_info *info = file->private_data;
@@ -8238,6 +8409,8 @@
 
 	/* did we read anything? */
 	if (!spd.nr_pages) {
+		long wait_index;
+
 		if (ret)
 			goto out;
 
@@ -8245,10 +8418,21 @@
 		if ((file->f_flags & O_NONBLOCK) || (flags & SPLICE_F_NONBLOCK))
 			goto out;
 
-		ret = wait_on_pipe(iter, iter->tr->buffer_percent);
+		wait_index = READ_ONCE(iter->wait_index);
+
+		ret = wait_on_pipe(iter, iter->snapshot ? 0 : iter->tr->buffer_percent);
 		if (ret)
 			goto out;
 
+		/* No need to wait after waking up when tracing is off */
+		if (!tracer_tracing_is_on(iter->tr))
+			goto out;
+
+		/* Make sure we see the new wait_index */
+		smp_rmb();
+		if (wait_index != iter->wait_index)
+			goto out;
+
 		goto again;
 	}
 
@@ -8259,12 +8443,35 @@
 	return ret;
 }
 
+/* An ioctl call with cmd 0 to the ring buffer file will wake up all waiters */
+static long tracing_buffers_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+	struct ftrace_buffer_info *info = file->private_data;
+	struct trace_iterator *iter = &info->iter;
+
+	if (cmd)
+		return -ENOIOCTLCMD;
+
+	mutex_lock(&trace_types_lock);
+
+	iter->wait_index++;
+	/* Make sure the waiters see the new wait_index */
+	smp_wmb();
+
+	ring_buffer_wake_waiters(iter->array_buffer->buffer, iter->cpu_file);
+
+	mutex_unlock(&trace_types_lock);
+	return 0;
+}
+
 static const struct file_operations tracing_buffers_fops = {
 	.open		= tracing_buffers_open,
 	.read		= tracing_buffers_read,
 	.poll		= tracing_buffers_poll,
 	.release	= tracing_buffers_release,
+	.flush		= tracing_buffers_flush,
 	.splice_read	= tracing_buffers_splice_read,
+	.unlocked_ioctl = tracing_buffers_ioctl,
 	.llseek		= no_llseek,
 };
 
@@ -8590,27 +8797,27 @@
 	}
 
 	/* per cpu trace_pipe */
-	trace_create_cpu_file("trace_pipe", 0444, d_cpu,
+	trace_create_cpu_file("trace_pipe", TRACE_MODE_READ, d_cpu,
 				tr, cpu, &tracing_pipe_fops);
 
 	/* per cpu trace */
-	trace_create_cpu_file("trace", 0644, d_cpu,
+	trace_create_cpu_file("trace", TRACE_MODE_WRITE, d_cpu,
 				tr, cpu, &tracing_fops);
 
-	trace_create_cpu_file("trace_pipe_raw", 0444, d_cpu,
+	trace_create_cpu_file("trace_pipe_raw", TRACE_MODE_READ, d_cpu,
 				tr, cpu, &tracing_buffers_fops);
 
-	trace_create_cpu_file("stats", 0444, d_cpu,
+	trace_create_cpu_file("stats", TRACE_MODE_READ, d_cpu,
 				tr, cpu, &tracing_stats_fops);
 
-	trace_create_cpu_file("buffer_size_kb", 0444, d_cpu,
+	trace_create_cpu_file("buffer_size_kb", TRACE_MODE_READ, d_cpu,
 				tr, cpu, &tracing_entries_fops);
 
 #ifdef CONFIG_TRACER_SNAPSHOT
-	trace_create_cpu_file("snapshot", 0644, d_cpu,
+	trace_create_cpu_file("snapshot", TRACE_MODE_WRITE, d_cpu,
 				tr, cpu, &snapshot_fops);
 
-	trace_create_cpu_file("snapshot_raw", 0444, d_cpu,
+	trace_create_cpu_file("snapshot_raw", TRACE_MODE_READ, d_cpu,
 				tr, cpu, &snapshot_raw_fops);
 #endif
 }
@@ -8664,12 +8871,33 @@
 	return cnt;
 }
 
+static int tracing_open_options(struct inode *inode, struct file *filp)
+{
+	struct trace_option_dentry *topt = inode->i_private;
+	int ret;
+
+	ret = tracing_check_open_get_tr(topt->tr);
+	if (ret)
+		return ret;
+
+	filp->private_data = inode->i_private;
+	return 0;
+}
+
+static int tracing_release_options(struct inode *inode, struct file *file)
+{
+	struct trace_option_dentry *topt = file->private_data;
+
+	trace_array_put(topt->tr);
+	return 0;
+}
 
 static const struct file_operations trace_options_fops = {
-	.open = tracing_open_generic,
+	.open = tracing_open_options,
 	.read = trace_options_read,
 	.write = trace_options_write,
 	.llseek	= generic_file_llseek,
+	.release = tracing_release_options,
 };
 
 /*
@@ -8816,8 +9044,8 @@
 	topt->opt = opt;
 	topt->tr = tr;
 
-	topt->entry = trace_create_file(opt->name, 0644, t_options, topt,
-				    &trace_options_fops);
+	topt->entry = trace_create_file(opt->name, TRACE_MODE_WRITE,
+					t_options, topt, &trace_options_fops);
 
 }
 
@@ -8892,7 +9120,7 @@
 	if (!t_options)
 		return NULL;
 
-	return trace_create_file(option, 0644, t_options,
+	return trace_create_file(option, TRACE_MODE_WRITE, t_options,
 				 (void *)&tr->trace_flags_index[index],
 				 &trace_options_core_fops);
 }
@@ -8953,6 +9181,8 @@
 			tracer_tracing_off(tr);
 			if (tr->current_trace->stop)
 				tr->current_trace->stop(tr);
+			/* Wake up any waiters */
+			ring_buffer_wake_waiters(buffer, RING_BUFFER_ALL_CPUS);
 		}
 		mutex_unlock(&trace_types_lock);
 	}
@@ -8999,9 +9229,6 @@
 	if (val > 100)
 		return -EINVAL;
 
-	if (!val)
-		val = 1;
-
 	tr->buffer_percent = val;
 
 	(*ppos)++;
@@ -9121,6 +9348,7 @@
 static void update_tracer_options(struct trace_array *tr)
 {
 	mutex_lock(&trace_types_lock);
+	tracer_options_updated = true;
 	__update_tracer_options(tr);
 	mutex_unlock(&trace_types_lock);
 }
@@ -9190,6 +9418,9 @@
 	if (!alloc_cpumask_var(&tr->tracing_cpumask, GFP_KERNEL))
 		goto out_free_tr;
 
+	if (!zalloc_cpumask_var(&tr->pipe_cpumask, GFP_KERNEL))
+		goto out_free_tr;
+
 	tr->trace_flags = global_trace.trace_flags & ~ZEROED_TRACE_FLAGS;
 
 	cpumask_copy(tr->tracing_cpumask, cpu_all_mask);
@@ -9231,6 +9462,7 @@
  out_free_tr:
 	ftrace_free_ftrace_ops(tr);
 	free_trace_buffers(tr);
+	free_cpumask_var(tr->pipe_cpumask);
 	free_cpumask_var(tr->tracing_cpumask);
 	kfree(tr->name);
 	kfree(tr);
@@ -9326,12 +9558,14 @@
 	tracefs_remove(tr->dir);
 	free_percpu(tr->last_func_repeats);
 	free_trace_buffers(tr);
+	clear_tracing_err_log(tr);
 
 	for (i = 0; i < tr->nr_topts; i++) {
 		kfree(tr->topts[i].topts);
 	}
 	kfree(tr->topts);
 
+	free_cpumask_var(tr->pipe_cpumask);
 	free_cpumask_var(tr->tracing_cpumask);
 	kfree(tr->name);
 	kfree(tr);
@@ -9417,28 +9651,28 @@
 	struct trace_event_file *file;
 	int cpu;
 
-	trace_create_file("available_tracers", 0444, d_tracer,
+	trace_create_file("available_tracers", TRACE_MODE_READ, d_tracer,
 			tr, &show_traces_fops);
 
-	trace_create_file("current_tracer", 0644, d_tracer,
+	trace_create_file("current_tracer", TRACE_MODE_WRITE, d_tracer,
 			tr, &set_tracer_fops);
 
-	trace_create_file("tracing_cpumask", 0644, d_tracer,
+	trace_create_file("tracing_cpumask", TRACE_MODE_WRITE, d_tracer,
 			  tr, &tracing_cpumask_fops);
 
-	trace_create_file("trace_options", 0644, d_tracer,
+	trace_create_file("trace_options", TRACE_MODE_WRITE, d_tracer,
 			  tr, &tracing_iter_fops);
 
-	trace_create_file("trace", 0644, d_tracer,
+	trace_create_file("trace", TRACE_MODE_WRITE, d_tracer,
 			  tr, &tracing_fops);
 
-	trace_create_file("trace_pipe", 0444, d_tracer,
+	trace_create_file("trace_pipe", TRACE_MODE_READ, d_tracer,
 			  tr, &tracing_pipe_fops);
 
-	trace_create_file("buffer_size_kb", 0644, d_tracer,
+	trace_create_file("buffer_size_kb", TRACE_MODE_WRITE, d_tracer,
 			  tr, &tracing_entries_fops);
 
-	trace_create_file("buffer_total_size_kb", 0444, d_tracer,
+	trace_create_file("buffer_total_size_kb", TRACE_MODE_READ, d_tracer,
 			  tr, &tracing_total_entries_fops);
 
 	trace_create_file("free_buffer", 0200, d_tracer,
@@ -9449,40 +9683,42 @@
 
 	file = __find_event_file(tr, "ftrace", "print");
 	if (file && file->dir)
-		trace_create_file("trigger", 0644, file->dir, file,
-				  &event_trigger_fops);
+		trace_create_file("trigger", TRACE_MODE_WRITE, file->dir,
+				  file, &event_trigger_fops);
 	tr->trace_marker_file = file;
 
 	trace_create_file("trace_marker_raw", 0220, d_tracer,
 			  tr, &tracing_mark_raw_fops);
 
-	trace_create_file("trace_clock", 0644, d_tracer, tr,
+	trace_create_file("trace_clock", TRACE_MODE_WRITE, d_tracer, tr,
 			  &trace_clock_fops);
 
-	trace_create_file("tracing_on", 0644, d_tracer,
+	trace_create_file("tracing_on", TRACE_MODE_WRITE, d_tracer,
 			  tr, &rb_simple_fops);
 
-	trace_create_file("timestamp_mode", 0444, d_tracer, tr,
+	trace_create_file("timestamp_mode", TRACE_MODE_READ, d_tracer, tr,
 			  &trace_time_stamp_mode_fops);
 
 	tr->buffer_percent = 50;
 
-	trace_create_file("buffer_percent", 0444, d_tracer,
+	trace_create_file("buffer_percent", TRACE_MODE_WRITE, d_tracer,
 			tr, &buffer_percent_fops);
 
 	create_trace_options_dir(tr);
 
+#ifdef CONFIG_TRACER_MAX_TRACE
 	trace_create_maxlat_file(tr, d_tracer);
+#endif
 
 	if (ftrace_create_function_files(tr, d_tracer))
 		MEM_FAIL(1, "Could not allocate function filter files");
 
 #ifdef CONFIG_TRACER_SNAPSHOT
-	trace_create_file("snapshot", 0644, d_tracer,
+	trace_create_file("snapshot", TRACE_MODE_WRITE, d_tracer,
 			  tr, &snapshot_fops);
 #endif
 
-	trace_create_file("error_log", 0644, d_tracer,
+	trace_create_file("error_log", TRACE_MODE_WRITE, d_tracer,
 			  tr, &tracing_err_log_fops);
 
 	for_each_tracing_cpu(cpu)
@@ -9675,19 +9911,19 @@
 	init_tracer_tracefs(&global_trace, NULL);
 	ftrace_init_tracefs_toplevel(&global_trace, NULL);
 
-	trace_create_file("tracing_thresh", 0644, NULL,
+	trace_create_file("tracing_thresh", TRACE_MODE_WRITE, NULL,
 			&global_trace, &tracing_thresh_fops);
 
-	trace_create_file("README", 0444, NULL,
+	trace_create_file("README", TRACE_MODE_READ, NULL,
 			NULL, &tracing_readme_fops);
 
-	trace_create_file("saved_cmdlines", 0444, NULL,
+	trace_create_file("saved_cmdlines", TRACE_MODE_READ, NULL,
 			NULL, &tracing_saved_cmdlines_fops);
 
-	trace_create_file("saved_cmdlines_size", 0644, NULL,
+	trace_create_file("saved_cmdlines_size", TRACE_MODE_WRITE, NULL,
 			  NULL, &tracing_saved_cmdlines_size_fops);
 
-	trace_create_file("saved_tgids", 0444, NULL,
+	trace_create_file("saved_tgids", TRACE_MODE_READ, NULL,
 			NULL, &tracing_saved_tgids_fops);
 
 	trace_eval_init();
@@ -9699,7 +9935,7 @@
 #endif
 
 #ifdef CONFIG_DYNAMIC_FTRACE
-	trace_create_file("dyn_ftrace_total_info", 0444, NULL,
+	trace_create_file("dyn_ftrace_total_info", TRACE_MODE_READ, NULL,
 			NULL, &tracing_dyn_info_fops);
 #endif
 
@@ -9799,6 +10035,12 @@
 	/* Output in nanoseconds only if we are using a clock in nanoseconds. */
 	if (trace_clocks[iter->tr->clock_id].in_ns)
 		iter->iter_flags |= TRACE_FILE_TIME_IN_NS;
+
+	/* Can not use kmalloc for iter.temp and iter.fmt */
+	iter->temp = static_temp_buf;
+	iter->temp_size = STATIC_TEMP_BUF_SIZE;
+	iter->fmt = static_fmt_buf;
+	iter->fmt_size = STATIC_FMT_BUF_SIZE;
 }
 
 void ftrace_dump(enum ftrace_dump_mode oops_dump_mode)
@@ -9831,11 +10073,6 @@
 
 	/* Simulate the iterator */
 	trace_init_global_iter(&iter);
-	/* Can not use kmalloc for iter.temp and iter.fmt */
-	iter.temp = static_temp_buf;
-	iter.temp_size = STATIC_TEMP_BUF_SIZE;
-	iter.fmt = static_fmt_buf;
-	iter.fmt_size = STATIC_FMT_BUF_SIZE;
 
 	for_each_tracing_cpu(cpu) {
 		atomic_inc(&per_cpu_ptr(iter.array_buffer->data, cpu)->disabled);
@@ -10039,12 +10276,14 @@
 	if (trace_create_savedcmd() < 0)
 		goto out_free_temp_buffer;
 
+	if (!zalloc_cpumask_var(&global_trace.pipe_cpumask, GFP_KERNEL))
+		goto out_free_savedcmd;
+
 	/* TODO: make the number of buffers hot pluggable with CPUS */
 	if (allocate_trace_buffers(&global_trace, ring_buf_size) < 0) {
 		MEM_FAIL(1, "tracer: failed to allocate ring buffer!\n");
-		goto out_free_savedcmd;
+		goto out_free_pipe_cpumask;
 	}
-
 	if (global_trace.buffer_disabled)
 		tracing_off();
 
@@ -10097,6 +10336,8 @@
 
 	return 0;
 
+out_free_pipe_cpumask:
+	free_cpumask_var(global_trace.pipe_cpumask);
 out_free_savedcmd:
 	free_saved_cmdlines_buffer(savedcmd);
 out_free_temp_buffer:
@@ -10123,6 +10364,8 @@
 			static_key_enable(&tracepoint_printk_key.key);
 	}
 	tracer_alloc_buffers();
+
+	init_events();
 }
 
 void __init trace_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace.h
@@ -22,11 +22,16 @@
 #include <linux/ctype.h>
 #include <linux/once_lite.h>
 
+#include "pid_list.h"
+
 #ifdef CONFIG_FTRACE_SYSCALLS
 #include <asm/unistd.h>		/* For NR_SYSCALLS	     */
 #include <asm/syscall.h>	/* some archs define it here */
 #endif
 
+#define TRACE_MODE_WRITE	0640
+#define TRACE_MODE_READ		0440
+
 enum trace_type {
 	__TRACE_FIRST_TYPE = 0,
 
@@ -78,6 +83,9 @@
 #undef __dynamic_array
 #define __dynamic_array(type, item)	type	item[];
 
+#undef __rel_dynamic_array
+#define __rel_dynamic_array(type, item)	type	item[];
+
 #undef F_STRUCT
 #define F_STRUCT(args...)		args
 
@@ -105,6 +113,12 @@
 #define MEM_FAIL(condition, fmt, ...)					\
 	DO_ONCE_LITE_IF(condition, pr_err, "ERROR: " fmt, ##__VA_ARGS__)
 
+#define FAULT_STRING "(fault)"
+
+#define HIST_STACKTRACE_DEPTH	16
+#define HIST_STACKTRACE_SIZE	(HIST_STACKTRACE_DEPTH * sizeof(unsigned long))
+#define HIST_STACKTRACE_SKIP	5
+
 /*
  * syscalls are special, and need special handling, this is why
  * they are not included in trace_entries.h
@@ -188,10 +202,14 @@
 	struct trace_option_dentry	*topts;
 };
 
-struct trace_pid_list {
-	int				pid_max;
-	unsigned long			*pids;
-};
+struct trace_pid_list *trace_pid_list_alloc(void);
+void trace_pid_list_free(struct trace_pid_list *pid_list);
+bool trace_pid_list_is_set(struct trace_pid_list *pid_list, unsigned int pid);
+int trace_pid_list_set(struct trace_pid_list *pid_list, unsigned int pid);
+int trace_pid_list_clear(struct trace_pid_list *pid_list, unsigned int pid);
+int trace_pid_list_first(struct trace_pid_list *pid_list, unsigned int *pid);
+int trace_pid_list_next(struct trace_pid_list *pid_list, unsigned int pid,
+			unsigned int *next);
 
 enum {
 	TRACE_PIDS		= BIT(0),
@@ -297,8 +315,7 @@
 	struct array_buffer	max_buffer;
 	bool			allocated_snapshot;
 #endif
-#if defined(CONFIG_TRACER_MAX_TRACE) || defined(CONFIG_HWLAT_TRACER) \
-	|| defined(CONFIG_OSNOISE_TRACER)
+#ifdef CONFIG_TRACER_MAX_TRACE
 	unsigned long		max_latency;
 #ifdef CONFIG_FSNOTIFY
 	struct dentry		*d_max_latency;
@@ -350,6 +367,8 @@
 	struct list_head	events;
 	struct trace_event_file *trace_marker_file;
 	cpumask_var_t		tracing_cpumask; /* only trace on set CPUs */
+	/* one per_cpu trace_pipe can be opened by only one user */
+	cpumask_var_t		pipe_cpumask;
 	int			ref;
 	int			trace_ref;
 #ifdef CONFIG_FUNCTION_TRACER
@@ -569,8 +588,12 @@
 void tracing_reset_online_cpus(struct array_buffer *buf);
 void tracing_reset_current(int cpu);
 void tracing_reset_all_online_cpus(void);
+void tracing_reset_all_online_cpus_unlocked(void);
 int tracing_open_generic(struct inode *inode, struct file *filp);
 int tracing_open_generic_tr(struct inode *inode, struct file *filp);
+int tracing_open_file_tr(struct inode *inode, struct file *filp);
+int tracing_release_file_tr(struct inode *inode, struct file *filp);
+int tracing_single_release_file_tr(struct inode *inode, struct file *filp);
 bool tracing_is_disabled(void);
 bool tracer_tracing_is_on(struct trace_array *tr);
 void tracer_tracing_on(struct trace_array *tr);
@@ -676,12 +699,11 @@
 		   void *cond_data);
 void update_max_tr_single(struct trace_array *tr,
 			  struct task_struct *tsk, int cpu);
-#endif /* CONFIG_TRACER_MAX_TRACE */
 
-#if (defined(CONFIG_TRACER_MAX_TRACE) || defined(CONFIG_HWLAT_TRACER) \
-	|| defined(CONFIG_OSNOISE_TRACER)) && defined(CONFIG_FSNOTIFY)
+#ifdef CONFIG_FSNOTIFY
 #define LATENCY_FS_NOTIFY
 #endif
+#endif /* CONFIG_TRACER_MAX_TRACE */
 
 #ifdef LATENCY_FS_NOTIFY
 void latency_fsnotify(struct trace_array *tr);
@@ -1357,14 +1379,26 @@
 	if (eflags & EVENT_FILE_FL_TRIGGER_COND)
 		*tt = event_triggers_call(file, buffer, entry, event);
 
-	if (test_bit(EVENT_FILE_FL_SOFT_DISABLED_BIT, &file->flags) ||
-	    (unlikely(file->flags & EVENT_FILE_FL_FILTERED) &&
-	     !filter_match_preds(file->filter, entry))) {
-		__trace_event_discard_commit(buffer, event);
-		return true;
-	}
+	if (likely(!(file->flags & (EVENT_FILE_FL_SOFT_DISABLED |
+				    EVENT_FILE_FL_FILTERED |
+				    EVENT_FILE_FL_PID_FILTER))))
+		return false;
+
+	if (file->flags & EVENT_FILE_FL_SOFT_DISABLED)
+		goto discard;
+
+	if (file->flags & EVENT_FILE_FL_FILTERED &&
+	    !filter_match_preds(file->filter, entry))
+		goto discard;
+
+	if ((file->flags & EVENT_FILE_FL_PID_FILTER) &&
+	    trace_event_ignore_this_pid(file))
+		goto discard;
 
 	return false;
+ discard:
+	__trace_event_discard_commit(buffer, event);
+	return true;
 }
 
 /**
@@ -1478,6 +1512,7 @@
 extern void trace_event_enable_tgid_record(bool enable);
 
 extern int event_trace_init(void);
+extern int init_events(void);
 extern int event_trace_add_tracer(struct dentry *parent, struct trace_array *tr);
 extern int event_trace_del_tracer(struct trace_array *tr);
 extern void __trace_early_add_events(struct trace_array *tr);
@@ -1586,6 +1621,9 @@
 extern int unregister_event_command(struct event_command *cmd);
 extern int register_trigger_hist_enable_disable_cmds(void);
 
+extern void event_file_get(struct trace_event_file *file);
+extern void event_file_put(struct trace_event_file *file);
+
 /**
  * struct event_trigger_ops - callbacks for trace event triggers
  *
@@ -1917,17 +1955,30 @@
 }
 
 /* Check the name is good for event/group/fields */
-static inline bool is_good_name(const char *name)
+static inline bool __is_good_name(const char *name, bool hash_ok)
 {
-	if (!isalpha(*name) && *name != '_')
+	if (!isalpha(*name) && *name != '_' && (!hash_ok || *name != '-'))
 		return false;
 	while (*++name != '\0') {
-		if (!isalpha(*name) && !isdigit(*name) && *name != '_')
+		if (!isalpha(*name) && !isdigit(*name) && *name != '_' &&
+		    (!hash_ok || *name != '-'))
 			return false;
 	}
 	return true;
 }
 
+/* Check the name is good for event/group/fields */
+static inline bool is_good_name(const char *name)
+{
+	return __is_good_name(name, false);
+}
+
+/* Check the name is good for system */
+static inline bool is_good_system_name(const char *name)
+{
+	return __is_good_name(name, true);
+}
+
 /* Convert certain expected symbols into '_' when generating event names */
 static inline void sanitize_event_name(char *name)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_boot.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_boot.c
@@ -300,7 +300,7 @@
 {
 	struct xbc_node *node;
 	const char *p, *handler;
-	int ret;
+	int ret = 0;
 
 	handler = xbc_node_get_data(hnode);
 
@@ -430,6 +430,8 @@
 		/* All digit started node should be instances. */
 		if (trace_boot_compose_hist_cmd(node, buf, size) == 0) {
 			tmp = kstrdup(buf, GFP_KERNEL);
+			if (!tmp)
+				return;
 			if (trigger_process_regex(file, buf) < 0)
 				pr_err("Failed to apply hist trigger: %s\n", tmp);
 			kfree(tmp);
@@ -439,6 +441,8 @@
 	if (xbc_node_find_subkey(hnode, "keys")) {
 		if (trace_boot_compose_hist_cmd(hnode, buf, size) == 0) {
 			tmp = kstrdup(buf, GFP_KERNEL);
+			if (!tmp)
+				return;
 			if (trigger_process_regex(file, buf) < 0)
 				pr_err("Failed to apply hist trigger: %s\n", tmp);
 			kfree(tmp);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_clock.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_clock.c
@@ -154,5 +154,5 @@
  */
 u64 notrace trace_clock_counter(void)
 {
-	return atomic64_add_return(1, &trace_counter);
+	return atomic64_inc_return(&trace_counter);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_dynevent.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_dynevent.c
@@ -118,6 +118,7 @@
 		if (ret)
 			break;
 	}
+	tracing_reset_all_online_cpus();
 	mutex_unlock(&event_mutex);
 out:
 	argv_free(argv);
@@ -214,6 +215,7 @@
 			break;
 	}
 out:
+	tracing_reset_all_online_cpus();
 	mutex_unlock(&event_mutex);
 
 	return ret;
@@ -262,7 +264,7 @@
 	if (ret)
 		return 0;
 
-	entry = tracefs_create_file("dynamic_events", 0644, NULL,
+	entry = tracefs_create_file("dynamic_events", TRACE_MODE_WRITE, NULL,
 				    NULL, &dynamic_events_ops);
 
 	/* Event list interface */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_eprobe.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_eprobe.c
@@ -16,6 +16,7 @@
 #include "trace_dynevent.h"
 #include "trace_probe.h"
 #include "trace_probe_tmpl.h"
+#include "trace_probe_kernel.h"
 
 #define EPROBE_EVENT_SYSTEM "eprobes"
 
@@ -226,6 +227,7 @@
 	struct probe_arg *parg = &ep->tp.args[i];
 	struct ftrace_event_field *field;
 	struct list_head *head;
+	int ret = -ENOENT;
 
 	head = trace_get_fields(ep->event);
 	list_for_each_entry(field, head, link) {
@@ -235,9 +237,20 @@
 			return 0;
 		}
 	}
+
+	/*
+	 * Argument not found on event. But allow for comm and COMM
+	 * to be used to get the current->comm.
+	 */
+	if (strcmp(parg->code->data, "COMM") == 0 ||
+	    strcmp(parg->code->data, "comm") == 0) {
+		parg->code->op = FETCH_OP_COMM;
+		ret = 0;
+	}
+
 	kfree(parg->code->data);
 	parg->code->data = NULL;
-	return -ENOENT;
+	return ret;
 }
 
 static int eprobe_event_define_fields(struct trace_event_call *event_call)
@@ -308,6 +321,24 @@
 
 	addr = rec + field->offset;
 
+	if (is_string_field(field)) {
+		switch (field->filter_type) {
+		case FILTER_DYN_STRING:
+			val = (unsigned long)(rec + (*(unsigned int *)addr & 0xffff));
+			break;
+		case FILTER_STATIC_STRING:
+			val = (unsigned long)addr;
+			break;
+		case FILTER_PTR_STRING:
+			val = (unsigned long)(*(char *)addr);
+			break;
+		default:
+			WARN_ON_ONCE(1);
+			return 0;
+		}
+		return val;
+	}
+
 	switch (field->size) {
 	case 1:
 		if (field->is_signed)
@@ -339,16 +370,38 @@
 
 static int get_eprobe_size(struct trace_probe *tp, void *rec)
 {
+	struct fetch_insn *code;
 	struct probe_arg *arg;
 	int i, len, ret = 0;
 
 	for (i = 0; i < tp->nr_args; i++) {
 		arg = tp->args + i;
-		if (unlikely(arg->dynamic)) {
+		if (arg->dynamic) {
 			unsigned long val;
 
-			val = get_event_field(arg->code, rec);
-			len = process_fetch_insn_bottom(arg->code + 1, val, NULL, NULL);
+			code = arg->code;
+ retry:
+			switch (code->op) {
+			case FETCH_OP_TP_ARG:
+				val = get_event_field(code, rec);
+				break;
+			case FETCH_OP_IMM:
+				val = code->immediate;
+				break;
+			case FETCH_OP_COMM:
+				val = (unsigned long)current->comm;
+				break;
+			case FETCH_OP_DATA:
+				val = (unsigned long)code->data;
+				break;
+			case FETCH_NOP_SYMBOL:	/* Ignore a place holder */
+				code++;
+				goto retry;
+			default:
+				continue;
+			}
+			code++;
+			len = process_fetch_insn_bottom(code, val, NULL, NULL);
 			if (len > 0)
 				ret += len;
 		}
@@ -366,8 +419,28 @@
 {
 	unsigned long val;
 
-	val = get_event_field(code, rec);
-	return process_fetch_insn_bottom(code + 1, val, dest, base);
+ retry:
+	switch (code->op) {
+	case FETCH_OP_TP_ARG:
+		val = get_event_field(code, rec);
+		break;
+	case FETCH_OP_IMM:
+		val = code->immediate;
+		break;
+	case FETCH_OP_COMM:
+		val = (unsigned long)current->comm;
+		break;
+	case FETCH_OP_DATA:
+		val = (unsigned long)code->data;
+		break;
+	case FETCH_NOP_SYMBOL:	/* Ignore a place holder */
+		code++;
+		goto retry;
+	default:
+		return -EILSEQ;
+	}
+	code++;
+	return process_fetch_insn_bottom(code, val, dest, base);
 }
 NOKPROBE_SYMBOL(process_fetch_insn)
 
@@ -375,29 +448,14 @@
 static nokprobe_inline int
 fetch_store_strlen_user(unsigned long addr)
 {
-	const void __user *uaddr =  (__force const void __user *)addr;
-
-	return strnlen_user_nofault(uaddr, MAX_STRING_SIZE);
+	return kern_fetch_store_strlen_user(addr);
 }
 
 /* Return the length of string -- including null terminal byte */
 static nokprobe_inline int
 fetch_store_strlen(unsigned long addr)
 {
-	int ret, len = 0;
-	u8 c;
-
-#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
-	if (addr < TASK_SIZE)
-		return fetch_store_strlen_user(addr);
-#endif
-
-	do {
-		ret = copy_from_kernel_nofault(&c, (u8 *)addr + len, 1);
-		len++;
-	} while (c && ret == 0 && len < MAX_STRING_SIZE);
-
-	return (ret < 0) ? ret : len;
+	return kern_fetch_store_strlen(addr);
 }
 
 /*
@@ -407,21 +465,7 @@
 static nokprobe_inline int
 fetch_store_string_user(unsigned long addr, void *dest, void *base)
 {
-	const void __user *uaddr =  (__force const void __user *)addr;
-	int maxlen = get_loc_len(*(u32 *)dest);
-	void *__dest;
-	long ret;
-
-	if (unlikely(!maxlen))
-		return -ENOMEM;
-
-	__dest = get_loc_data(dest, base);
-
-	ret = strncpy_from_user_nofault(__dest, uaddr, maxlen);
-	if (ret >= 0)
-		*(u32 *)dest = make_data_loc(ret, __dest - base);
-
-	return ret;
+	return kern_fetch_store_string_user(addr, dest, base);
 }
 
 /*
@@ -431,29 +475,7 @@
 static nokprobe_inline int
 fetch_store_string(unsigned long addr, void *dest, void *base)
 {
-	int maxlen = get_loc_len(*(u32 *)dest);
-	void *__dest;
-	long ret;
-
-#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
-	if ((unsigned long)addr < TASK_SIZE)
-		return fetch_store_string_user(addr, dest, base);
-#endif
-
-	if (unlikely(!maxlen))
-		return -ENOMEM;
-
-	__dest = get_loc_data(dest, base);
-
-	/*
-	 * Try to get string again, since the string can be changed while
-	 * probing.
-	 */
-	ret = strncpy_from_kernel_nofault(__dest, (void *)addr, maxlen);
-	if (ret >= 0)
-		*(u32 *)dest = make_data_loc(ret, __dest - base);
-
-	return ret;
+	return kern_fetch_store_string(addr, dest, base);
 }
 
 static nokprobe_inline int
@@ -545,6 +567,12 @@
 {
 	struct eprobe_data *edata = data->private_data;
 
+	if (unlikely(!rec))
+		return;
+
+	if (unlikely(!rec))
+		return;
+
 	__eprobe_trace_func(edata, rec);
 }
 
@@ -697,6 +725,7 @@
 	struct trace_eprobe *ep;
 	bool enabled;
 	int ret = 0;
+	int cnt = 0;
 
 	tp = trace_probe_primary_from_call(call);
 	if (WARN_ON_ONCE(!tp))
@@ -720,12 +749,25 @@
 		if (ret)
 			break;
 		enabled = true;
+		cnt++;
 	}
 
 	if (ret) {
 		/* Failed to enable one of them. Roll back all */
-		if (enabled)
-			disable_eprobe(ep, file->tr);
+		if (enabled) {
+			/*
+			 * It's a bug if one failed for something other than memory
+			 * not being available but another eprobe succeeded.
+			 */
+			WARN_ON_ONCE(ret != -ENOMEM);
+
+			list_for_each_entry(pos, trace_probe_probe_list(tp), list) {
+				ep = container_of(pos, struct trace_eprobe, tp);
+				disable_eprobe(ep, file->tr);
+				if (!--cnt)
+					break;
+			}
+		}
 		if (file)
 			trace_probe_remove_file(tp, file);
 		else
@@ -849,6 +891,10 @@
 	if (ep->tp.args[i].code->op == FETCH_OP_TP_ARG)
 		ret = trace_eprobe_tp_arg_update(ep, i);
 
+	/* Handle symbols "@" */
+	if (!ret)
+		ret = traceprobe_update_arg(&ep->tp.args[i]);
+
 	return ret;
 }
 
@@ -933,6 +979,11 @@
 		goto error;
 	}
 	ret = dyn_event_add(&ep->devent, &ep->tp.event->call);
+	if (ret < 0) {
+		trace_probe_unregister_event_call(&ep->tp);
+		mutex_unlock(&event_mutex);
+		goto error;
+	}
 	mutex_unlock(&event_mutex);
 	return ret;
 parse_error:
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_event_perf.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_event_perf.c
@@ -157,7 +157,7 @@
 	int i;
 
 	if (--tp_event->perf_refcount > 0)
-		goto out;
+		return;
 
 	tp_event->class->reg(tp_event, TRACE_REG_PERF_UNREGISTER, NULL);
 
@@ -176,8 +176,6 @@
 			perf_trace_buf[i] = NULL;
 		}
 	}
-out:
-	trace_event_put_ref(tp_event);
 }
 
 static int perf_trace_event_open(struct perf_event *p_event)
@@ -241,6 +239,7 @@
 	mutex_lock(&event_mutex);
 	perf_trace_event_close(p_event);
 	perf_trace_event_unreg(p_event);
+	trace_event_put_ref(p_event->tp_event);
 	mutex_unlock(&event_mutex);
 }
 
@@ -292,6 +291,7 @@
 	mutex_lock(&event_mutex);
 	perf_trace_event_close(p_event);
 	perf_trace_event_unreg(p_event);
+	trace_event_put_ref(p_event->tp_event);
 	mutex_unlock(&event_mutex);
 
 	destroy_local_trace_kprobe(p_event->tp_event);
@@ -347,6 +347,7 @@
 	mutex_lock(&event_mutex);
 	perf_trace_event_close(p_event);
 	perf_trace_event_unreg(p_event);
+	trace_event_put_ref(p_event->tp_event);
 	mutex_unlock(&event_mutex);
 	destroy_local_trace_uprobe(p_event->tp_event);
 }
@@ -355,10 +356,16 @@
 int perf_trace_add(struct perf_event *p_event, int flags)
 {
 	struct trace_event_call *tp_event = p_event->tp_event;
+	struct hw_perf_event *hwc = &p_event->hw;
 
 	if (!(flags & PERF_EF_START))
 		p_event->hw.state = PERF_HES_STOPPED;
 
+	if (is_sampling_event(p_event)) {
+		hwc->last_period = hwc->sample_period;
+		perf_swevent_set_period(p_event);
+	}
+
 	/*
 	 * If TRACE_REG_PERF_ADD returns false; no custom action was performed
 	 * and we need to take the default action of enqueueing our event on
@@ -400,7 +407,8 @@
 	BUILD_BUG_ON(PERF_MAX_TRACE_SIZE % sizeof(unsigned long));
 
 	if (WARN_ONCE(size > PERF_MAX_TRACE_SIZE,
-		      "perf buffer not large enough"))
+		      "perf buffer not large enough, wanted %d, have %d",
+		      size, PERF_MAX_TRACE_SIZE))
 		return NULL;
 
 	*rctxp = rctx = perf_swevent_get_recursion_context();
@@ -441,13 +449,13 @@
 	if (!rcu_is_watching())
 		return;
 
-	if ((unsigned long)ops->private != smp_processor_id())
-		return;
-
 	bit = ftrace_test_recursion_trylock(ip, parent_ip);
 	if (bit < 0)
 		return;
 
+	if ((unsigned long)ops->private != smp_processor_id())
+		goto out;
+
 	event = container_of(ops, struct perf_event, ftrace_ops);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_events.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_events.c
@@ -40,6 +40,14 @@
 static LIST_HEAD(ftrace_common_fields);
 static bool eventdir_initialized;
 
+static LIST_HEAD(module_strings);
+
+struct module_string {
+	struct list_head	next;
+	struct module		*module;
+	char			*str;
+};
+
 #define GFP_TRACE (GFP_KERNEL | __GFP_ZERO)
 
 static struct kmem_cache *field_cachep;
@@ -168,6 +176,7 @@
 
 	__generic_field(int, CPU, FILTER_CPU);
 	__generic_field(int, cpu, FILTER_CPU);
+	__generic_field(int, common_cpu, FILTER_CPU);
 	__generic_field(char *, COMM, FILTER_COMM);
 	__generic_field(char *, comm, FILTER_COMM);
 
@@ -218,19 +227,16 @@
 	return tail->offset + tail->size;
 }
 
-/*
- * Check if the referenced field is an array and return true,
- * as arrays are OK to dereference.
- */
-static bool test_field(const char *fmt, struct trace_event_call *call)
+
+static struct trace_event_fields *find_event_field(const char *fmt,
+						   struct trace_event_call *call)
 {
 	struct trace_event_fields *field = call->class->fields_array;
-	const char *array_descriptor;
 	const char *p = fmt;
 	int len;
 
 	if (!(len = str_has_prefix(fmt, "REC->")))
-		return false;
+		return NULL;
 	fmt += len;
 	for (p = fmt; *p; p++) {
 		if (!isalnum(*p) && *p != '_')
@@ -239,16 +245,134 @@
 	len = p - fmt;
 
 	for (; field->type; field++) {
-		if (strncmp(field->name, fmt, len) ||
-		    field->name[len])
+		if (strncmp(field->name, fmt, len) || field->name[len])
 			continue;
-		array_descriptor = strchr(field->type, '[');
-		/* This is an array and is OK to dereference. */
-		return array_descriptor != NULL;
+
+		return field;
+	}
+	return NULL;
+}
+
+/*
+ * Check if the referenced field is an array and return true,
+ * as arrays are OK to dereference.
+ */
+static bool test_field(const char *fmt, struct trace_event_call *call)
+{
+	struct trace_event_fields *field;
+
+	field = find_event_field(fmt, call);
+	if (!field)
+		return false;
+
+	/* This is an array and is OK to dereference. */
+	return strchr(field->type, '[') != NULL;
+}
+
+/* Look for a string within an argument */
+static bool find_print_string(const char *arg, const char *str, const char *end)
+{
+	const char *r;
+
+	r = strstr(arg, str);
+	return r && r < end;
+}
+
+/* Return true if the argument pointer is safe */
+static bool process_pointer(const char *fmt, int len, struct trace_event_call *call)
+{
+	const char *r, *e, *a;
+
+	e = fmt + len;
+
+	/* Find the REC-> in the argument */
+	r = strstr(fmt, "REC->");
+	if (r && r < e) {
+		/*
+		 * Addresses of events on the buffer, or an array on the buffer is
+		 * OK to dereference. There's ways to fool this, but
+		 * this is to catch common mistakes, not malicious code.
+		 */
+		a = strchr(fmt, '&');
+		if ((a && (a < r)) || test_field(r, call))
+			return true;
+	} else if (find_print_string(fmt, "__get_dynamic_array(", e)) {
+		return true;
+	} else if (find_print_string(fmt, "__get_rel_dynamic_array(", e)) {
+		return true;
+	} else if (find_print_string(fmt, "__get_dynamic_array_len(", e)) {
+		return true;
+	} else if (find_print_string(fmt, "__get_rel_dynamic_array_len(", e)) {
+		return true;
+	} else if (find_print_string(fmt, "__get_sockaddr(", e)) {
+		return true;
+	} else if (find_print_string(fmt, "__get_rel_sockaddr(", e)) {
+		return true;
 	}
 	return false;
 }
 
+/* Return true if the string is safe */
+static bool process_string(const char *fmt, int len, struct trace_event_call *call)
+{
+	const char *r, *e, *s;
+
+	e = fmt + len;
+
+	/*
+	 * There are several helper functions that return strings.
+	 * If the argument contains a function, then assume its field is valid.
+	 * It is considered that the argument has a function if it has:
+	 *   alphanumeric or '_' before a parenthesis.
+	 */
+	s = fmt;
+	do {
+		int i;
+
+		r = strstr(s, "(");
+		if (!r || r >= e)
+			break;
+		for (i = 1; r - i >= s; i++) {
+			char ch = *(r - i);
+			if (isspace(ch))
+				continue;
+			if (isalnum(ch) || ch == '_')
+				return true;
+			/* Anything else, this isn't a function */
+			break;
+		}
+		/* A function could be wrapped in parethesis, try the next one */
+		s = r + 1;
+	} while (s < e);
+
+	/*
+	 * Check for arrays. If the argument has: foo[REC->val]
+	 * then it is very likely that foo is an array of strings
+	 * that are safe to use.
+	 */
+	r = strstr(s, "[");
+	if (r && r < e) {
+		r = strstr(r, "REC->");
+		if (r && r < e)
+			return true;
+	}
+
+	/*
+	 * If there's any strings in the argument consider this arg OK as it
+	 * could be: REC->field ? "foo" : "bar" and we don't want to get into
+	 * verifying that logic here.
+	 */
+	if (find_print_string(fmt, "\"", e))
+		return true;
+
+	/* Dereferenced strings are also valid like any other pointer */
+	if (process_pointer(fmt, len, call))
+		return true;
+
+	/* Make sure the field is found, and consider it OK for now if it is */
+	return find_event_field(fmt, call) != NULL;
+}
+
 /*
  * Examine the print fmt of the event looking for unsafe dereference
  * pointers using %p* that could be recorded in the trace event and
@@ -258,13 +382,14 @@
 static void test_event_printk(struct trace_event_call *call)
 {
 	u64 dereference_flags = 0;
+	u64 string_flags = 0;
 	bool first = true;
-	const char *fmt, *c, *r, *a;
+	const char *fmt;
 	int parens = 0;
 	char in_quote = 0;
 	int start_arg = 0;
 	int arg = 0;
-	int i;
+	int i, e;
 
 	fmt = call->print_fmt;
 
@@ -348,8 +473,16 @@
 						star = true;
 						continue;
 					}
-					if ((fmt[i + j] == 's') && star)
-						arg++;
+					if ((fmt[i + j] == 's')) {
+						if (star)
+							arg++;
+						if (WARN_ONCE(arg == 63,
+							      "Too many args for event: %s",
+							      trace_event_name(call)))
+							return;
+						dereference_flags |= 1ULL << arg;
+						string_flags |= 1ULL << arg;
+					}
 					break;
 				}
 				break;
@@ -377,35 +510,47 @@
 		case ',':
 			if (in_quote || parens)
 				continue;
+			e = i;
 			i++;
 			while (isspace(fmt[i]))
 				i++;
-			start_arg = i;
-			if (!(dereference_flags & (1ULL << arg)))
-				goto next_arg;
 
-			/* Find the REC-> in the argument */
-			c = strchr(fmt + i, ',');
-			r = strstr(fmt + i, "REC->");
-			if (r && (!c || r < c)) {
-				/*
-				 * Addresses of events on the buffer,
-				 * or an array on the buffer is
-				 * OK to dereference.
-				 * There's ways to fool this, but
-				 * this is to catch common mistakes,
-				 * not malicious code.
-				 */
-				a = strchr(fmt + i, '&');
-				if ((a && (a < r)) || test_field(r, call))
+			/*
+			 * If start_arg is zero, then this is the start of the
+			 * first argument. The processing of the argument happens
+			 * when the end of the argument is found, as it needs to
+			 * handle paranthesis and such.
+			 */
+			if (!start_arg) {
+				start_arg = i;
+				/* Balance out the i++ in the for loop */
+				i--;
+				continue;
+			}
+
+			if (dereference_flags & (1ULL << arg)) {
+				if (string_flags & (1ULL << arg)) {
+					if (process_string(fmt + start_arg, e - start_arg, call))
+						dereference_flags &= ~(1ULL << arg);
+				} else if (process_pointer(fmt + start_arg, e - start_arg, call))
 					dereference_flags &= ~(1ULL << arg);
 			}
-		next_arg:
-			i--;
+
+			start_arg = i;
 			arg++;
+			/* Balance out the i++ in the for loop */
+			i--;
 		}
 	}
 
+	if (dereference_flags & (1ULL << arg)) {
+		if (string_flags & (1ULL << arg)) {
+			if (process_string(fmt + start_arg, i - start_arg, call))
+				dereference_flags &= ~(1ULL << arg);
+		} else if (process_pointer(fmt + start_arg, i - start_arg, call))
+			dereference_flags &= ~(1ULL << arg);
+	}
+
 	/*
 	 * If you triggered the below warning, the trace event reported
 	 * uses an unsafe dereference pointer %p*. As the data stored
@@ -578,7 +723,6 @@
 {
 	struct trace_event_call *call = file->event_call;
 	struct trace_array *tr = file->tr;
-	unsigned long file_flags = file->flags;
 	int ret = 0;
 	int disable;
 
@@ -602,6 +746,8 @@
 				break;
 			disable = file->flags & EVENT_FILE_FL_SOFT_DISABLED;
 			clear_bit(EVENT_FILE_FL_SOFT_MODE_BIT, &file->flags);
+			/* Disable use of trace_buffered_event */
+			trace_buffered_event_disable();
 		} else
 			disable = !(file->flags & EVENT_FILE_FL_SOFT_MODE);
 
@@ -640,6 +786,8 @@
 			if (atomic_inc_return(&file->sm_ref) > 1)
 				break;
 			set_bit(EVENT_FILE_FL_SOFT_MODE_BIT, &file->flags);
+			/* Enable use of trace_buffered_event */
+			trace_buffered_event_enable();
 		}
 
 		if (!(file->flags & EVENT_FILE_FL_ENABLED)) {
@@ -679,15 +827,6 @@
 		break;
 	}
 
-	/* Enable or disable use of trace_buffered_event */
-	if ((file_flags & EVENT_FILE_FL_SOFT_DISABLED) !=
-	    (file->flags & EVENT_FILE_FL_SOFT_DISABLED)) {
-		if (file->flags & EVENT_FILE_FL_SOFT_DISABLED)
-			trace_buffered_event_enable();
-		else
-			trace_buffered_event_disable();
-	}
-
 	return ret;
 }
 
@@ -885,10 +1024,10 @@
 	tracepoint_synchronize_unregister();
 
 	if ((type & TRACE_PIDS) && pid_list)
-		trace_free_pid_list(pid_list);
+		trace_pid_list_free(pid_list);
 
 	if ((type & TRACE_NO_PIDS) && no_pid_list)
-		trace_free_pid_list(no_pid_list);
+		trace_pid_list_free(no_pid_list);
 }
 
 static void ftrace_clear_event_pids(struct trace_array *tr, int type)
@@ -959,26 +1098,38 @@
 	}
 }
 
-static void remove_event_file_dir(struct trace_event_file *file)
+void event_file_get(struct trace_event_file *file)
 {
-	struct dentry *dir = file->dir;
-	struct dentry *child;
+	atomic_inc(&file->ref);
+}
 
-	if (dir) {
-		spin_lock(&dir->d_lock);	/* probably unneeded */
-		list_for_each_entry(child, &dir->d_subdirs, d_child) {
-			if (d_really_is_positive(child))	/* probably unneeded */
-				d_inode(child)->i_private = NULL;
-		}
-		spin_unlock(&dir->d_lock);
+void event_file_put(struct trace_event_file *file)
+{
+	if (WARN_ON_ONCE(!atomic_read(&file->ref))) {
+		if (file->flags & EVENT_FILE_FL_FREED)
+			kmem_cache_free(file_cachep, file);
+		return;
+	}
 
-		tracefs_remove(dir);
+	if (atomic_dec_and_test(&file->ref)) {
+		/* Count should only go to zero when it is freed */
+		if (WARN_ON_ONCE(!(file->flags & EVENT_FILE_FL_FREED)))
+			return;
+		kmem_cache_free(file_cachep, file);
 	}
+}
+
+static void remove_event_file_dir(struct trace_event_file *file)
+{
+	struct dentry *dir = file->dir;
+
+	tracefs_remove(dir);
 
 	list_del(&file->list);
 	remove_subsystem(file->system);
 	free_event_filter(file->filter);
-	kmem_cache_free(file_cachep, file);
+	file->flags |= EVENT_FILE_FL_FREED;
+	event_file_put(file);
 }
 
 /*
@@ -1351,7 +1502,7 @@
 		flags = file->flags;
 	mutex_unlock(&event_mutex);
 
-	if (!file)
+	if (!file || flags & EVENT_FILE_FL_FREED)
 		return -ENODEV;
 
 	if (flags & EVENT_FILE_FL_ENABLED &&
@@ -1389,7 +1540,7 @@
 		ret = -ENODEV;
 		mutex_lock(&event_mutex);
 		file = event_file_data(filp);
-		if (likely(file))
+		if (likely(file && !(file->flags & EVENT_FILE_FL_FREED)))
 			ret = ftrace_event_enable_disable(file, val);
 		mutex_unlock(&event_mutex);
 		break;
@@ -1623,6 +1774,7 @@
 	return 0;
 }
 
+#ifdef CONFIG_PERF_EVENTS
 static ssize_t
 event_id_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
 {
@@ -1637,6 +1789,7 @@
 
 	return simple_read_from_buffer(ubuf, cnt, ppos, buf, len);
 }
+#endif
 
 static ssize_t
 event_filter_read(struct file *filp, char __user *ubuf, size_t cnt,
@@ -1658,7 +1811,7 @@
 
 	mutex_lock(&event_mutex);
 	file = event_file_data(filp);
-	if (file)
+	if (file && !(file->flags & EVENT_FILE_FL_FREED))
 		print_event_filter(file, s);
 	mutex_unlock(&event_mutex);
 
@@ -1967,7 +2120,7 @@
 
 	if (filtered_pids) {
 		tracepoint_synchronize_unregister();
-		trace_free_pid_list(filtered_pids);
+		trace_pid_list_free(filtered_pids);
 	} else if (pid_list && !other_pids) {
 		register_pid_events(tr);
 	}
@@ -2068,9 +2221,10 @@
 };
 
 static const struct file_operations ftrace_enable_fops = {
-	.open = tracing_open_generic,
+	.open = tracing_open_file_tr,
 	.read = event_enable_read,
 	.write = event_enable_write,
+	.release = tracing_release_file_tr,
 	.llseek = default_llseek,
 };
 
@@ -2081,15 +2235,18 @@
 	.release = seq_release,
 };
 
+#ifdef CONFIG_PERF_EVENTS
 static const struct file_operations ftrace_event_id_fops = {
 	.read = event_id_read,
 	.llseek = default_llseek,
 };
+#endif
 
 static const struct file_operations ftrace_event_filter_fops = {
-	.open = tracing_open_generic,
+	.open = tracing_open_file_tr,
 	.read = event_filter_read,
 	.write = event_filter_write,
+	.release = tracing_release_file_tr,
 	.llseek = default_llseek,
 };
 
@@ -2312,7 +2469,8 @@
 	/* the ftrace system is special, do not create enable or filter files */
 	if (strcmp(name, "ftrace") != 0) {
 
-		entry = tracefs_create_file("filter", 0644, dir->entry, dir,
+		entry = tracefs_create_file("filter", TRACE_MODE_WRITE,
+					    dir->entry, dir,
 					    &ftrace_subsystem_filter_fops);
 		if (!entry) {
 			kfree(system->filter);
@@ -2320,7 +2478,7 @@
 			pr_warn("Could not create tracefs '%s/filter' entry\n", name);
 		}
 
-		trace_create_file("enable", 0644, dir->entry, dir,
+		trace_create_file("enable", TRACE_MODE_WRITE, dir->entry, dir,
 				  &ftrace_system_enable_fops);
 	}
 
@@ -2402,12 +2560,12 @@
 	}
 
 	if (call->class->reg && !(call->flags & TRACE_EVENT_FL_IGNORE_ENABLE))
-		trace_create_file("enable", 0644, file->dir, file,
+		trace_create_file("enable", TRACE_MODE_WRITE, file->dir, file,
 				  &ftrace_enable_fops);
 
 #ifdef CONFIG_PERF_EVENTS
 	if (call->event.type && call->class->reg)
-		trace_create_file("id", 0444, file->dir,
+		trace_create_file("id", TRACE_MODE_READ, file->dir,
 				  (void *)(long)call->event.type,
 				  &ftrace_event_id_fops);
 #endif
@@ -2423,22 +2581,22 @@
 	 * triggers or filters.
 	 */
 	if (!(call->flags & TRACE_EVENT_FL_IGNORE_ENABLE)) {
-		trace_create_file("filter", 0644, file->dir, file,
-				  &ftrace_event_filter_fops);
+		trace_create_file("filter", TRACE_MODE_WRITE, file->dir,
+				  file, &ftrace_event_filter_fops);
 
-		trace_create_file("trigger", 0644, file->dir, file,
-				  &event_trigger_fops);
+		trace_create_file("trigger", TRACE_MODE_WRITE, file->dir,
+				  file, &event_trigger_fops);
 	}
 
 #ifdef CONFIG_HIST_TRIGGERS
-	trace_create_file("hist", 0444, file->dir, file,
+	trace_create_file("hist", TRACE_MODE_READ, file->dir, file,
 			  &event_hist_fops);
 #endif
 #ifdef CONFIG_HIST_TRIGGERS_DEBUG
-	trace_create_file("hist_debug", 0444, file->dir, file,
+	trace_create_file("hist_debug", TRACE_MODE_READ, file->dir, file,
 			  &event_hist_debug_fops);
 #endif
-	trace_create_file("format", 0444, file->dir, call,
+	trace_create_file("format", TRACE_MODE_READ, file->dir, call,
 			  &ftrace_event_format_fops);
 
 #ifdef CONFIG_TRACE_EVENT_INJECT
@@ -2632,6 +2790,76 @@
 	}
 }
 
+static void add_str_to_module(struct module *module, char *str)
+{
+	struct module_string *modstr;
+
+	modstr = kmalloc(sizeof(*modstr), GFP_KERNEL);
+
+	/*
+	 * If we failed to allocate memory here, then we'll just
+	 * let the str memory leak when the module is removed.
+	 * If this fails to allocate, there's worse problems than
+	 * a leaked string on module removal.
+	 */
+	if (WARN_ON_ONCE(!modstr))
+		return;
+
+	modstr->module = module;
+	modstr->str = str;
+
+	list_add(&modstr->next, &module_strings);
+}
+
+static void update_event_fields(struct trace_event_call *call,
+				struct trace_eval_map *map)
+{
+	struct ftrace_event_field *field;
+	struct list_head *head;
+	char *ptr;
+	char *str;
+	int len = strlen(map->eval_string);
+
+	/* Dynamic events should never have field maps */
+	if (WARN_ON_ONCE(call->flags & TRACE_EVENT_FL_DYNAMIC))
+		return;
+
+	head = trace_get_fields(call);
+	list_for_each_entry(field, head, link) {
+		ptr = strchr(field->type, '[');
+		if (!ptr)
+			continue;
+		ptr++;
+
+		if (!isalpha(*ptr) && *ptr != '_')
+			continue;
+
+		if (strncmp(map->eval_string, ptr, len) != 0)
+			continue;
+
+		str = kstrdup(field->type, GFP_KERNEL);
+		if (WARN_ON_ONCE(!str))
+			return;
+		ptr = str + (ptr - field->type);
+		ptr = eval_replace(ptr, map, len);
+		/* enum/sizeof string smaller than value */
+		if (WARN_ON_ONCE(!ptr)) {
+			kfree(str);
+			continue;
+		}
+
+		/*
+		 * If the event is part of a module, then we need to free the string
+		 * when the module is removed. Otherwise, it will stay allocated
+		 * until a reboot.
+		 */
+		if (call->module)
+			add_str_to_module(call->module, str);
+
+		field->type = str;
+	}
+}
+
 void trace_event_eval_update(struct trace_eval_map **map, int len)
 {
 	struct trace_event_call *call, *p;
@@ -2667,8 +2895,10 @@
 					first = false;
 				}
 				update_event_printk(call, map[i]);
+				update_event_fields(call, map[i]);
 			}
 		}
+		cond_resched();
 	}
 	up_write(&trace_event_sem);
 }
@@ -2677,18 +2907,29 @@
 trace_create_new_event(struct trace_event_call *call,
 		       struct trace_array *tr)
 {
+	struct trace_pid_list *no_pid_list;
+	struct trace_pid_list *pid_list;
 	struct trace_event_file *file;
 
 	file = kmem_cache_alloc(file_cachep, GFP_TRACE);
 	if (!file)
 		return NULL;
 
+	pid_list = rcu_dereference_protected(tr->filtered_pids,
+					     lockdep_is_held(&event_mutex));
+	no_pid_list = rcu_dereference_protected(tr->filtered_no_pids,
+					     lockdep_is_held(&event_mutex));
+
+	if (pid_list || no_pid_list)
+		file->flags |= EVENT_FILE_FL_PID_FILTER;
+
 	file->event_call = call;
 	file->tr = tr;
 	atomic_set(&file->sm_ref, 0);
 	atomic_set(&file->tm_ref, 0);
 	INIT_LIST_HEAD(&file->triggers);
 	list_add(&file->list, &tr->events);
+	event_file_get(file);
 
 	return file;
 }
@@ -2776,7 +3017,10 @@
 		 * TRACE_REG_UNREGISTER.
 		 */
 		if (file->flags & EVENT_FILE_FL_ENABLED)
-			return -EBUSY;
+			goto busy;
+
+		if (file->flags & EVENT_FILE_FL_WAS_ENABLED)
+			tr->clear_trace = true;
 		/*
 		 * The do_for_each_event_file_safe() is
 		 * a double loop. After finding the call for this
@@ -2789,6 +3033,12 @@
 	__trace_remove_event_call(call);
 
 	return 0;
+ busy:
+	/* No need to clear the trace now */
+	list_for_each_entry(tr, &ftrace_trace_arrays, list) {
+		tr->clear_trace = false;
+	}
+	return -EBUSY;
 }
 
 /* Remove an event_call */
@@ -2840,6 +3090,7 @@
 static void trace_module_remove_events(struct module *mod)
 {
 	struct trace_event_call *call, *p;
+	struct module_string *modstr, *m;
 
 	down_write(&trace_event_sem);
 	list_for_each_entry_safe(call, p, &ftrace_events, list) {
@@ -2848,6 +3099,14 @@
 		if (call->module == mod)
 			__trace_remove_event_call(call);
 	}
+	/* Check for any strings allocade for this module */
+	list_for_each_entry_safe(modstr, m, &module_strings, next) {
+		if (modstr->module != mod)
+			continue;
+		list_del(&modstr->next);
+		kfree(modstr->str);
+		kfree(modstr);
+	}
 	up_write(&trace_event_sem);
 
 	/*
@@ -2858,7 +3117,7 @@
 	 * over from this module may be passed to the new module events and
 	 * unexpected results may occur.
 	 */
-	tracing_reset_all_online_cpus();
+	tracing_reset_all_online_cpus_unlocked();
 }
 
 static int trace_module_notify(struct notifier_block *self,
@@ -3433,7 +3692,7 @@
 	struct dentry *d_events;
 	struct dentry *entry;
 
-	entry = tracefs_create_file("set_event", 0644, parent,
+	entry = tracefs_create_file("set_event", TRACE_MODE_WRITE, parent,
 				    tr, &ftrace_set_event_fops);
 	if (!entry) {
 		pr_warn("Could not create tracefs 'set_event' entry\n");
@@ -3446,7 +3705,7 @@
 		return -ENOMEM;
 	}
 
-	entry = trace_create_file("enable", 0644, d_events,
+	entry = trace_create_file("enable", TRACE_MODE_WRITE, d_events,
 				  tr, &ftrace_tr_enable_fops);
 	if (!entry) {
 		pr_warn("Could not create tracefs 'enable' entry\n");
@@ -3455,24 +3714,25 @@
 
 	/* There are not as crucial, just warn if they are not created */
 
-	entry = tracefs_create_file("set_event_pid", 0644, parent,
+	entry = tracefs_create_file("set_event_pid", TRACE_MODE_WRITE, parent,
 				    tr, &ftrace_set_event_pid_fops);
 	if (!entry)
 		pr_warn("Could not create tracefs 'set_event_pid' entry\n");
 
-	entry = tracefs_create_file("set_event_notrace_pid", 0644, parent,
-				    tr, &ftrace_set_event_notrace_pid_fops);
+	entry = tracefs_create_file("set_event_notrace_pid",
+				    TRACE_MODE_WRITE, parent, tr,
+				    &ftrace_set_event_notrace_pid_fops);
 	if (!entry)
 		pr_warn("Could not create tracefs 'set_event_notrace_pid' entry\n");
 
 	/* ring buffer internal formats */
-	entry = trace_create_file("header_page", 0444, d_events,
+	entry = trace_create_file("header_page", TRACE_MODE_READ, d_events,
 				  ring_buffer_print_page_header,
 				  &ftrace_show_header_fops);
 	if (!entry)
 		pr_warn("Could not create tracefs 'header_page' entry\n");
 
-	entry = trace_create_file("header_event", 0444, d_events,
+	entry = trace_create_file("header_event", TRACE_MODE_READ, d_events,
 				  ring_buffer_print_entry_header,
 				  &ftrace_show_header_fops);
 	if (!entry)
@@ -3689,8 +3949,8 @@
 	if (!tr)
 		return -ENODEV;
 
-	entry = tracefs_create_file("available_events", 0444, NULL,
-				    tr, &ftrace_avail_fops);
+	entry = tracefs_create_file("available_events", TRACE_MODE_READ,
+				    NULL, tr, &ftrace_avail_fops);
 	if (!entry)
 		pr_warn("Could not create tracefs 'available_events' entry\n");
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_events_filter.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_events_filter.c
@@ -5,6 +5,7 @@
  * Copyright (C) 2009 Tom Zanussi <tzanussi@gmail.com>
  */
 
+#include <linux/uaccess.h>
 #include <linux/module.h>
 #include <linux/ctype.h>
 #include <linux/mutex.h>
@@ -654,6 +655,52 @@
 DEFINE_EQUALITY_PRED(16);
 DEFINE_EQUALITY_PRED(8);
 
+/* user space strings temp buffer */
+#define USTRING_BUF_SIZE	1024
+
+struct ustring_buffer {
+	char		buffer[USTRING_BUF_SIZE];
+};
+
+static __percpu struct ustring_buffer *ustring_per_cpu;
+
+static __always_inline char *test_string(char *str)
+{
+	struct ustring_buffer *ubuf;
+	char *kstr;
+
+	if (!ustring_per_cpu)
+		return NULL;
+
+	ubuf = this_cpu_ptr(ustring_per_cpu);
+	kstr = ubuf->buffer;
+
+	/* For safety, do not trust the string pointer */
+	if (!strncpy_from_kernel_nofault(kstr, str, USTRING_BUF_SIZE))
+		return NULL;
+	return kstr;
+}
+
+static __always_inline char *test_ustring(char *str)
+{
+	struct ustring_buffer *ubuf;
+	char __user *ustr;
+	char *kstr;
+
+	if (!ustring_per_cpu)
+		return NULL;
+
+	ubuf = this_cpu_ptr(ustring_per_cpu);
+	kstr = ubuf->buffer;
+
+	/* user space address? */
+	ustr = (char __user *)str;
+	if (!strncpy_from_user_nofault(kstr, ustr, USTRING_BUF_SIZE))
+		return NULL;
+
+	return kstr;
+}
+
 /* Filter predicate for fixed sized arrays of characters */
 static int filter_pred_string(struct filter_pred *pred, void *event)
 {
@@ -667,19 +714,43 @@
 	return match;
 }
 
-/* Filter predicate for char * pointers */
-static int filter_pred_pchar(struct filter_pred *pred, void *event)
+static __always_inline int filter_pchar(struct filter_pred *pred, char *str)
 {
-	char **addr = (char **)(event + pred->offset);
 	int cmp, match;
-	int len = strlen(*addr) + 1;	/* including tailing '\0' */
+	int len;
 
-	cmp = pred->regex.match(*addr, &pred->regex, len);
+	len = strlen(str) + 1;	/* including tailing '\0' */
+	cmp = pred->regex.match(str, &pred->regex, len);
 
 	match = cmp ^ pred->not;
 
 	return match;
 }
+/* Filter predicate for char * pointers */
+static int filter_pred_pchar(struct filter_pred *pred, void *event)
+{
+	char **addr = (char **)(event + pred->offset);
+	char *str;
+
+	str = test_string(*addr);
+	if (!str)
+		return 0;
+
+	return filter_pchar(pred, str);
+}
+
+/* Filter predicate for char * pointers in user space*/
+static int filter_pred_pchar_user(struct filter_pred *pred, void *event)
+{
+	char **addr = (char **)(event + pred->offset);
+	char *str;
+
+	str = test_ustring(*addr);
+	if (!str)
+		return 0;
+
+	return filter_pchar(pred, str);
+}
 
 /*
  * Filter predicate for dynamic sized arrays of characters.
@@ -1158,6 +1229,7 @@
 	struct filter_pred *pred = NULL;
 	char num_buf[24];	/* Big enough to hold an address */
 	char *field_name;
+	bool ustring = false;
 	char q;
 	u64 val;
 	int len;
@@ -1192,6 +1264,12 @@
 		return -EINVAL;
 	}
 
+	/* See if the field is a user space string */
+	if ((len = str_has_prefix(str + i, ".ustring"))) {
+		ustring = true;
+		i += len;
+	}
+
 	while (isspace(str[i]))
 		i++;
 
@@ -1320,8 +1398,20 @@
 
 		} else if (field->filter_type == FILTER_DYN_STRING)
 			pred->fn = filter_pred_strloc;
-		else
-			pred->fn = filter_pred_pchar;
+		else {
+
+			if (!ustring_per_cpu) {
+				/* Once allocated, keep it around for good */
+				ustring_per_cpu = alloc_percpu(struct ustring_buffer);
+				if (!ustring_per_cpu)
+					goto err_mem;
+			}
+
+			if (ustring)
+				pred->fn = filter_pred_pchar_user;
+			else
+				pred->fn = filter_pred_pchar;
+		}
 		/* go past the last quote */
 		i++;
 
@@ -1387,6 +1477,9 @@
 err_free:
 	kfree(pred);
 	return -EINVAL;
+err_mem:
+	kfree(pred);
+	return -ENOMEM;
 }
 
 enum {
@@ -1779,6 +1872,9 @@
 	struct event_filter *filter = NULL;
 	int err;
 
+	if (file->flags & EVENT_FILE_FL_FREED)
+		return -ENODEV;
+
 	if (!strcmp(strstrip(filter_string), "0")) {
 		filter_disable(file);
 		filter = event_filter(file);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_events_hist.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_events_hist.c
@@ -315,10 +315,6 @@
 #define for_each_hist_key_field(i, hist_data)	\
 	for ((i) = (hist_data)->n_vals; (i) < (hist_data)->n_fields; (i)++)
 
-#define HIST_STACKTRACE_DEPTH	16
-#define HIST_STACKTRACE_SIZE	(HIST_STACKTRACE_DEPTH * sizeof(unsigned long))
-#define HIST_STACKTRACE_SKIP	5
-
 #define HITCOUNT_IDX		0
 #define HIST_KEY_SIZE_MAX	(MAX_FILTER_STR_VAL + HIST_STACKTRACE_SIZE)
 
@@ -452,7 +448,7 @@
 	 * event param, and is passed to the synthetic event
 	 * invocation.
 	 */
-	unsigned int		var_ref_idx[TRACING_MAP_VARS_MAX];
+	unsigned int		var_ref_idx[SYNTH_FIELDS_MAX];
 	struct synth_event	*synth_event;
 	bool			use_trace_keyword;
 	char			*synth_event_name;
@@ -1127,6 +1123,9 @@
 {
 	const char *field_name = "";
 
+	if (WARN_ON_ONCE(!field))
+		return field_name;
+
 	if (level > 1)
 		return field_name;
 
@@ -1699,6 +1698,8 @@
 		hist_field->fn = flags & HIST_FIELD_FL_LOG2 ? hist_field_log2 :
 			hist_field_bucket;
 		hist_field->operands[0] = create_hist_field(hist_data, field, fl, NULL);
+		if (!hist_field->operands[0])
+			goto free;
 		hist_field->size = hist_field->operands[0]->size;
 		hist_field->type = kstrdup_const(hist_field->operands[0]->type, GFP_KERNEL);
 		if (!hist_field->type)
@@ -1733,9 +1734,10 @@
 		if (!hist_field->type)
 			goto free;
 
-		if (field->filter_type == FILTER_STATIC_STRING)
+		if (field->filter_type == FILTER_STATIC_STRING) {
 			hist_field->fn = hist_field_string;
-		else if (field->filter_type == FILTER_DYN_STRING)
+			hist_field->size = field->size;
+		} else if (field->filter_type == FILTER_DYN_STRING)
 			hist_field->fn = hist_field_dynstring;
 		else
 			hist_field->fn = hist_field_pstring;
@@ -1837,8 +1839,11 @@
 	return err;
  free:
 	kfree(ref_field->system);
+	ref_field->system = NULL;
 	kfree(ref_field->event_name);
+	ref_field->event_name = NULL;
 	kfree(ref_field->name);
+	ref_field->name = NULL;
 
 	goto out;
 }
@@ -1891,7 +1896,9 @@
 			return ref_field;
 		}
 	}
-
+	/* Sanity check to avoid out-of-bound write on 'hist_data->var_refs' */
+	if (hist_data->n_var_refs >= TRACING_MAP_VARS_MAX)
+		return NULL;
 	ref_field = create_hist_field(var_field->hist_data, NULL, flags, NULL);
 	if (ref_field) {
 		if (init_var_ref(ref_field, var_field, system, event_name)) {
@@ -2048,9 +2055,9 @@
 			/*
 			 * For backward compatibility, if field_name
 			 * was "cpu", then we treat this the same as
-			 * common_cpu.
+			 * common_cpu. This also works for "CPU".
 			 */
-			if (strcmp(field_name, "cpu") == 0) {
+			if (field && field->filter_type == FILTER_CPU) {
 				*flags |= HIST_FIELD_FL_CPU;
 			} else {
 				hist_err(tr, HIST_ERR_FIELD_NOT_FOUND,
@@ -2219,6 +2226,8 @@
 		(HIST_FIELD_FL_TIMESTAMP | HIST_FIELD_FL_TIMESTAMP_USECS);
 	expr->fn = hist_field_unary_minus;
 	expr->operands[0] = operand1;
+	expr->size = operand1->size;
+	expr->is_signed = operand1->is_signed;
 	expr->operator = FIELD_OP_UNARY_MINUS;
 	expr->name = expr_str(expr, 0);
 	expr->type = kstrdup_const(operand1->type, GFP_KERNEL);
@@ -2358,6 +2367,7 @@
 
 	/* The operand sizes should be the same, so just pick one */
 	expr->size = operand1->size;
+	expr->is_signed = operand1->is_signed;
 
 	expr->operator = field_op;
 	expr->name = expr_str(expr, 0);
@@ -2690,8 +2700,10 @@
 		if (val->flags & HIST_FIELD_FL_STRING) {
 			char *str = elt_data->field_var_str[j++];
 			char *val_str = (char *)(uintptr_t)var_val;
+			unsigned int size;
 
-			strscpy(str, val_str, STR_VAR_LEN_MAX);
+			size = min(val->size, STR_VAR_LEN_MAX);
+			strscpy(str, val_str, size);
 			var_val = (u64)(uintptr_t)str;
 		}
 		tracing_map_set_var(elt, var_idx, var_val);
@@ -3179,6 +3191,7 @@
 	while (params) {
 		if (data->n_params >= SYNTH_FIELDS_MAX) {
 			hist_err(tr, HIST_ERR_TOO_MANY_PARAMS, 0);
+			ret = -EINVAL;
 			goto out;
 		}
 
@@ -3414,9 +3427,12 @@
 	    && field->is_dynamic)
 		return 0;
 
+	if (strstr(hist_field->type, "long[") && field->is_stack)
+		return 0;
+
 	if (strcmp(field->type, hist_field->type) != 0) {
 		if (field->size != hist_field->size ||
-		    field->is_signed != hist_field->is_signed)
+		    (!field->is_string && field->is_signed != hist_field->is_signed))
 			return -EINVAL;
 	}
 
@@ -3515,6 +3531,10 @@
 
 	lockdep_assert_held(&event_mutex);
 
+	/* Sanity check to avoid out-of-bound write on 'data->var_ref_idx' */
+	if (data->n_params > SYNTH_FIELDS_MAX)
+		return -EINVAL;
+
 	if (data->use_trace_keyword)
 		synth_event_name = data->synth_event_name;
 	else
@@ -3578,6 +3598,7 @@
 
 			var_ref_idx = find_var_ref_idx(hist_data, var_ref);
 			if (WARN_ON(var_ref_idx < 0)) {
+				kfree(p);
 				ret = var_ref_idx;
 				goto err;
 			}
@@ -4046,6 +4067,8 @@
 
 			s = kstrdup(field_str, GFP_KERNEL);
 			if (!s) {
+				kfree(hist_data->attrs->var_defs.name[n_vars]);
+				hist_data->attrs->var_defs.name[n_vars] = NULL;
 				ret = -ENOMEM;
 				goto free;
 			}
@@ -4471,7 +4494,7 @@
 
 			if (hist_field->flags & HIST_FIELD_FL_STACKTRACE)
 				cmp_fn = tracing_map_cmp_none;
-			else if (!field)
+			else if (!field || hist_field->flags & HIST_FIELD_FL_CPU)
 				cmp_fn = tracing_map_cmp_num(hist_field->size,
 							     hist_field->is_signed);
 			else if (is_string_field(field))
@@ -4578,6 +4601,7 @@
 			if (hist_field->flags & HIST_FIELD_FL_STRING) {
 				unsigned int str_start, var_str_idx, idx;
 				char *str, *val_str;
+				unsigned int size;
 
 				str_start = hist_data->n_field_var_str +
 					hist_data->n_save_var_str;
@@ -4586,7 +4610,9 @@
 
 				str = elt_data->field_var_str[idx];
 				val_str = (char *)(uintptr_t)hist_val;
-				strscpy(str, val_str, STR_VAR_LEN_MAX);
+
+				size = min(hist_field->size, STR_VAR_LEN_MAX);
+				strscpy(str, val_str, size);
 
 				hist_val = (u64)(uintptr_t)str;
 			}
@@ -4662,6 +4688,9 @@
 	void *key = NULL;
 	unsigned int i;
 
+	if (unlikely(!rbe))
+		return;
+
 	memset(compound_key, 0, hist_data->key_size);
 
 	for_each_hist_key_field(i, hist_data) {
@@ -4917,10 +4946,12 @@
 {
 	int ret;
 
-	ret = security_locked_down(LOCKDOWN_TRACEFS);
+	ret = tracing_open_file_tr(inode, file);
 	if (ret)
 		return ret;
 
+	/* Clear private_data to avoid warning in single_open() */
+	file->private_data = NULL;
 	return single_open(file, hist_show, file);
 }
 
@@ -4928,7 +4959,7 @@
 	.open = event_hist_open,
 	.read = seq_read,
 	.llseek = seq_lseek,
-	.release = single_release,
+	.release = tracing_single_release_file_tr,
 };
 
 #ifdef CONFIG_HIST_TRIGGERS_DEBUG
@@ -5189,10 +5220,12 @@
 {
 	int ret;
 
-	ret = security_locked_down(LOCKDOWN_TRACEFS);
+	ret = tracing_open_file_tr(inode, file);
 	if (ret)
 		return ret;
 
+	/* Clear private_data to avoid warning in single_open() */
+	file->private_data = NULL;
 	return single_open(file, hist_debug_show, file);
 }
 
@@ -5200,7 +5233,7 @@
 	.open = event_hist_debug_open,
 	.read = seq_read,
 	.llseek = seq_lseek,
-	.release = single_release,
+	.release = tracing_single_release_file_tr,
 };
 #endif
 
@@ -5914,13 +5947,16 @@
 	if (get_named_trigger_data(trigger_data))
 		goto enable;
 
-	if (has_hist_vars(hist_data))
-		save_hist_vars(hist_data);
-
 	ret = create_actions(hist_data);
 	if (ret)
 		goto out_unreg;
 
+	if (has_hist_vars(hist_data) || hist_data->n_var_refs) {
+		ret = save_hist_vars(hist_data);
+		if (ret)
+			goto out_unreg;
+	}
+
 	ret = tracing_map_init(hist_data->map);
 	if (ret)
 		goto out_unreg;
@@ -5936,7 +5972,7 @@
 	/* Just return zero, not the number of registered triggers */
 	ret = 0;
  out:
-	if (ret == 0)
+	if (ret == 0 && glob[0])
 		hist_err_clear();
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_events_inject.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_events_inject.c
@@ -321,7 +321,8 @@
 }
 
 const struct file_operations event_inject_fops = {
-	.open = tracing_open_generic,
+	.open = tracing_open_file_tr,
 	.read = event_inject_read,
 	.write = event_inject_write,
+	.release = tracing_release_file_tr,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_events_synth.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_events_synth.c
@@ -17,6 +17,8 @@
 /* for gfp flag names */
 #include <linux/trace_events.h>
 #include <trace/events/mmflags.h>
+#include "trace_probe.h"
+#include "trace_probe_kernel.h"
 
 #include "trace_synth.h"
 
@@ -163,6 +165,14 @@
 	return false;
 }
 
+static int synth_field_is_stack(char *type)
+{
+	if (strstr(type, "long[") != NULL)
+		return true;
+
+	return false;
+}
+
 static int synth_field_string_size(char *type)
 {
 	char buf[4], *end, *start;
@@ -238,6 +248,8 @@
 		size = sizeof(gfp_t);
 	else if (synth_field_is_string(type))
 		size = synth_field_string_size(type);
+	else if (synth_field_is_stack(type))
+		size = 0;
 
 	return size;
 }
@@ -281,7 +293,9 @@
 	else if (strcmp(type, "gfp_t") == 0)
 		fmt = "%x";
 	else if (synth_field_is_string(type))
-		fmt = "%.*s";
+		fmt = "%s";
+	else if (synth_field_is_stack(type))
+		fmt = "%s";
 
 	return fmt;
 }
@@ -361,6 +375,23 @@
 						 i == se->n_fields - 1 ? "" : " ");
 				n_u64 += STR_VAR_LEN_MAX / sizeof(u64);
 			}
+		} else if (se->fields[i]->is_stack) {
+			u32 offset, data_offset, len;
+			unsigned long *p, *end;
+
+			offset = (u32)entry->fields[n_u64];
+			data_offset = offset & 0xffff;
+			len = offset >> 16;
+
+			p = (void *)entry + data_offset;
+			end = (void *)p + len - (sizeof(long) - 1);
+
+			trace_seq_printf(s, "%s=STACK:\n", se->fields[i]->name);
+
+			for (; *p && p < end; p++)
+				trace_seq_printf(s, "=> %pS\n", (void *)*p);
+			n_u64++;
+
 		} else {
 			struct trace_print_flags __flags[] = {
 			    __def_gfpflag_names, {-1, NULL} };
@@ -401,6 +432,7 @@
 {
 	unsigned int len = 0;
 	char *str_field;
+	int ret;
 
 	if (is_dynamic) {
 		u32 data_offset;
@@ -409,25 +441,70 @@
 		data_offset += event->n_u64 * sizeof(u64);
 		data_offset += data_size;
 
-		str_field = (char *)entry + data_offset;
-
-		len = strlen(str_val) + 1;
-		strscpy(str_field, str_val, len);
+		len = kern_fetch_store_strlen((unsigned long)str_val);
 
 		data_offset |= len << 16;
 		*(u32 *)&entry->fields[*n_u64] = data_offset;
 
+		ret = kern_fetch_store_string((unsigned long)str_val, &entry->fields[*n_u64], entry);
+
 		(*n_u64)++;
 	} else {
 		str_field = (char *)&entry->fields[*n_u64];
 
-		strscpy(str_field, str_val, STR_VAR_LEN_MAX);
+#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
+		if ((unsigned long)str_val < TASK_SIZE)
+			ret = strncpy_from_user_nofault(str_field, (const void __user *)str_val, STR_VAR_LEN_MAX);
+		else
+#endif
+			ret = strncpy_from_kernel_nofault(str_field, str_val, STR_VAR_LEN_MAX);
+
+		if (ret < 0)
+			strcpy(str_field, FAULT_STRING);
+
 		(*n_u64) += STR_VAR_LEN_MAX / sizeof(u64);
 	}
 
 	return len;
 }
 
+static unsigned int trace_stack(struct synth_trace_event *entry,
+				 struct synth_event *event,
+				 long *stack,
+				 unsigned int data_size,
+				 unsigned int *n_u64)
+{
+	unsigned int len;
+	u32 data_offset;
+	void *data_loc;
+
+	data_offset = struct_size(entry, fields, event->n_u64);
+	data_offset += data_size;
+
+	for (len = 0; len < HIST_STACKTRACE_DEPTH; len++) {
+		if (!stack[len])
+			break;
+	}
+
+	/* Include the zero'd element if it fits */
+	if (len < HIST_STACKTRACE_DEPTH)
+		len++;
+
+	len *= sizeof(long);
+
+	/* Find the dynamic section to copy the stack into. */
+	data_loc = (void *)entry + data_offset;
+	memcpy(data_loc, stack, len);
+
+	/* Fill in the field that holds the offset/len combo */
+	data_offset |= len << 16;
+	*(u32 *)&entry->fields[*n_u64] = data_offset;
+
+	(*n_u64)++;
+
+	return len;
+}
+
 static notrace void trace_event_raw_event_synth(void *__data,
 						u64 *var_ref_vals,
 						unsigned int *var_ref_idx)
@@ -454,7 +531,7 @@
 		val_idx = var_ref_idx[field_pos];
 		str_val = (char *)(long)var_ref_vals[val_idx];
 
-		len = strlen(str_val) + 1;
+		len = kern_fetch_store_strlen((unsigned long)str_val);
 
 		fields_size += len;
 	}
@@ -480,6 +557,12 @@
 					   event->fields[i]->is_dynamic,
 					   data_size, &n_u64);
 			data_size += len; /* only dynamic string increments */
+		} else if (event->fields[i]->is_stack) {
+			long *stack = (long *)(long)var_ref_vals[val_idx];
+
+			len = trace_stack(entry, event, stack,
+					   data_size, &n_u64);
+			data_size += len;
 		} else {
 			struct synth_field *field = event->fields[i];
 			u64 val = var_ref_vals[val_idx];
@@ -542,6 +625,9 @@
 		    event->fields[i]->is_dynamic)
 			pos += snprintf(buf + pos, LEN_OR_ZERO,
 				", __get_str(%s)", event->fields[i]->name);
+		else if (event->fields[i]->is_stack)
+			pos += snprintf(buf + pos, LEN_OR_ZERO,
+				", __get_stacktrace(%s)", event->fields[i]->name);
 		else
 			pos += snprintf(buf + pos, LEN_OR_ZERO,
 					", REC->%s", event->fields[i]->name);
@@ -678,7 +764,8 @@
 		ret = -EINVAL;
 		goto free;
 	} else if (size == 0) {
-		if (synth_field_is_string(field->type)) {
+		if (synth_field_is_string(field->type) ||
+		    synth_field_is_stack(field->type)) {
 			char *type;
 
 			len = sizeof("__data_loc ") + strlen(field->type) + 1;
@@ -709,6 +796,8 @@
 
 	if (synth_field_is_string(field->type))
 		field->is_string = true;
+	else if (synth_field_is_stack(field->type))
+		field->is_stack = true;
 
 	field->is_signed = synth_field_signed(field->type);
  out:
@@ -767,6 +856,39 @@
 	{}
 };
 
+static int synth_event_reg(struct trace_event_call *call,
+		    enum trace_reg type, void *data)
+{
+	struct synth_event *event = container_of(call, struct synth_event, call);
+	int ret;
+
+	switch (type) {
+#ifdef CONFIG_PERF_EVENTS
+	case TRACE_REG_PERF_REGISTER:
+#endif
+	case TRACE_REG_REGISTER:
+		if (!try_module_get(event->mod))
+			return -EBUSY;
+		break;
+	default:
+		break;
+	}
+
+	ret = trace_event_reg(call, type, data);
+
+	switch (type) {
+#ifdef CONFIG_PERF_EVENTS
+	case TRACE_REG_PERF_UNREGISTER:
+#endif
+	case TRACE_REG_UNREGISTER:
+		module_put(event->mod);
+		break;
+	default:
+		break;
+	}
+	return ret;
+}
+
 static int register_synth_event(struct synth_event *event)
 {
 	struct trace_event_call *call = &event->call;
@@ -796,7 +918,7 @@
 		goto out;
 	}
 	call->flags = TRACE_EVENT_FL_TRACEPOINT;
-	call->class->reg = trace_event_reg;
+	call->class->reg = synth_event_reg;
 	call->class->probe = trace_event_raw_event_synth;
 	call->data = event;
 	call->tp = event->tp;
@@ -809,10 +931,9 @@
 	}
 
 	ret = set_synth_event_print_fmt(call);
-	if (ret < 0) {
+	/* unregister_trace_event() will be called inside */
+	if (ret < 0)
 		trace_remove_event_call(call);
-		goto err;
-	}
  out:
 	return ret;
  err:
@@ -1265,12 +1386,12 @@
 				goto err;
 			}
 
-			fields[n_fields++] = field;
 			if (n_fields == SYNTH_FIELDS_MAX) {
 				synth_err(SYNTH_ERR_TOO_MANY_FIELDS, 0);
 				ret = -EINVAL;
 				goto err;
 			}
+			fields[n_fields++] = field;
 
 			n_fields_this_loop++;
 		}
@@ -1406,7 +1527,6 @@
 	mutex_unlock(&event_mutex);
 
 	if (mod) {
-		mutex_lock(&trace_types_lock);
 		/*
 		 * It is safest to reset the ring buffer if the module
 		 * being unloaded registered any events that were
@@ -1418,7 +1538,6 @@
 		 * occur.
 		 */
 		tracing_reset_all_online_cpus();
-		mutex_unlock(&trace_types_lock);
 	}
 
 	return ret;
@@ -2053,6 +2172,13 @@
 
 	last_cmd_set(raw_command);
 
+	name = raw_command;
+
+	/* Don't try to process if not our system */
+	if (name[0] != 's' || name[1] != ':')
+		return -ECANCELED;
+	name += 2;
+
 	p = strpbrk(raw_command, " \t");
 	if (!p) {
 		synth_err(SYNTH_ERR_INVALID_CMD, 0);
@@ -2061,12 +2187,6 @@
 
 	fields = skip_spaces(p);
 
-	name = raw_command;
-
-	if (name[0] != 's' || name[1] != ':')
-		return -ECANCELED;
-	name += 2;
-
 	/* This interface accepts group name prefix */
 	if (strchr(name, '/')) {
 		len = str_has_prefix(name, SYNTH_SYSTEM "/");
@@ -2227,8 +2347,8 @@
 	if (err)
 		goto err;
 
-	entry = tracefs_create_file("synthetic_events", 0644, NULL,
-				    NULL, &synth_events_fops);
+	entry = tracefs_create_file("synthetic_events", TRACE_MODE_WRITE,
+				    NULL, NULL, &synth_events_fops);
 	if (!entry) {
 		err = -ENODEV;
 		goto err;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_events_trigger.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_events_trigger.c
@@ -128,7 +128,8 @@
 {
 	struct event_trigger_data *data;
 
-	list_for_each_entry_rcu(data, &file->triggers, list) {
+	list_for_each_entry_rcu(data, &file->triggers, list,
+				lockdep_is_held(&event_mutex)) {
 		if (data->flags & EVENT_TRIGGER_FL_PROBE)
 			continue;
 		return true;
@@ -955,6 +956,16 @@
 		struct trace_buffer *buffer, void *rec,
 		struct ring_buffer_event *event)
 {
+	struct trace_event_file *file = data->private_data;
+
+	if (file) {
+		if (tracer_tracing_is_on(file->tr))
+			return;
+
+		tracer_tracing_on(file->tr);
+		return;
+	}
+
 	if (tracing_is_on())
 		return;
 
@@ -966,8 +977,15 @@
 		      struct trace_buffer *buffer, void *rec,
 		      struct ring_buffer_event *event)
 {
-	if (tracing_is_on())
-		return;
+	struct trace_event_file *file = data->private_data;
+
+	if (file) {
+		if (tracer_tracing_is_on(file->tr))
+			return;
+	} else {
+		if (tracing_is_on())
+			return;
+	}
 
 	if (!data->count)
 		return;
@@ -975,7 +993,10 @@
 	if (data->count != -1)
 		(data->count)--;
 
-	tracing_on();
+	if (file)
+		tracer_tracing_on(file->tr);
+	else
+		tracing_on();
 }
 
 static void
@@ -983,6 +1004,16 @@
 		 struct trace_buffer *buffer, void *rec,
 		 struct ring_buffer_event *event)
 {
+	struct trace_event_file *file = data->private_data;
+
+	if (file) {
+		if (!tracer_tracing_is_on(file->tr))
+			return;
+
+		tracer_tracing_off(file->tr);
+		return;
+	}
+
 	if (!tracing_is_on())
 		return;
 
@@ -994,8 +1025,15 @@
 		       struct trace_buffer *buffer, void *rec,
 		       struct ring_buffer_event *event)
 {
-	if (!tracing_is_on())
-		return;
+	struct trace_event_file *file = data->private_data;
+
+	if (file) {
+		if (!tracer_tracing_is_on(file->tr))
+			return;
+	} else {
+		if (!tracing_is_on())
+			return;
+	}
 
 	if (!data->count)
 		return;
@@ -1003,7 +1041,10 @@
 	if (data->count != -1)
 		(data->count)--;
 
-	tracing_off();
+	if (file)
+		tracer_tracing_off(file->tr);
+	else
+		tracing_off();
 }
 
 static int
@@ -1200,7 +1241,12 @@
 		   struct trace_buffer *buffer,  void *rec,
 		   struct ring_buffer_event *event)
 {
-	trace_dump_stack(STACK_SKIP);
+	struct trace_event_file *file = data->private_data;
+
+	if (file)
+		__trace_stack(file->tr, tracing_gen_ctx(), STACK_SKIP);
+	else
+		trace_dump_stack(STACK_SKIP);
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_functions_graph.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_functions_graph.c
@@ -1244,6 +1244,7 @@
 	if (data) {
 		free_percpu(data->cpu_data);
 		kfree(data);
+		iter->private = NULL;
 	}
 }
 
@@ -1340,7 +1341,7 @@
 	if (ret)
 		return 0;
 
-	trace_create_file("max_graph_depth", 0644, NULL,
+	trace_create_file("max_graph_depth", TRACE_MODE_WRITE, NULL,
 			  NULL, &graph_depth_fops);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_hwlat.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_hwlat.c
@@ -339,7 +339,7 @@
 	cpumask_clear(current_mask);
 	cpumask_set_cpu(next_cpu, current_mask);
 
-	sched_setaffinity(0, current_mask);
+	set_cpus_allowed_ptr(current, current_mask);
 	return;
 
  change_mode:
@@ -446,7 +446,7 @@
 
 	}
 
-	sched_setaffinity(kthread->pid, current_mask);
+	set_cpus_allowed_ptr(kthread, current_mask);
 
 	kdata->kthread = kthread;
 	wake_up_process(kthread);
@@ -491,18 +491,18 @@
 static int start_cpu_kthread(unsigned int cpu)
 {
 	struct task_struct *kthread;
-	char comm[24];
 
-	snprintf(comm, 24, "hwlatd/%d", cpu);
+	/* Do not start a new hwlatd thread if it is already running */
+	if (per_cpu(hwlat_per_cpu_data, cpu).kthread)
+		return 0;
 
-	kthread = kthread_create_on_cpu(kthread_fn, NULL, cpu, comm);
+	kthread = kthread_run_on_cpu(kthread_fn, NULL, cpu, "hwlatd/%u");
 	if (IS_ERR(kthread)) {
 		pr_err(BANNER "could not start sampling thread\n");
 		return -ENOMEM;
 	}
 
 	per_cpu(hwlat_per_cpu_data, cpu).kthread = kthread;
-	wake_up_process(kthread);
 
 	return 0;
 }
@@ -520,6 +520,8 @@
 	if (!hwlat_busy || hwlat_data.thread_mode != MODE_PER_CPU)
 		goto out_unlock;
 
+	if (!cpu_online(cpu))
+		goto out_unlock;
 	if (!cpumask_test_cpu(cpu, tr->tracing_cpumask))
 		goto out_unlock;
 
@@ -588,9 +590,6 @@
 	 */
 	cpumask_and(current_mask, cpu_online_mask, tr->tracing_cpumask);
 
-	for_each_online_cpu(cpu)
-		per_cpu(hwlat_per_cpu_data, cpu).kthread = NULL;
-
 	for_each_cpu(cpu, current_mask) {
 		retval = start_cpu_kthread(cpu);
 		if (retval)
@@ -638,7 +637,7 @@
 	else
 		seq_printf(s, "%s", thread_mode_str[mode]);
 
-	if (mode != MODE_MAX)
+	if (mode < MODE_MAX - 1) /* if mode is any but last */
 		seq_puts(s, " ");
 
 	return 0;
@@ -782,21 +781,21 @@
 	if (!top_dir)
 		return -ENOMEM;
 
-	hwlat_sample_window = tracefs_create_file("window", 0640,
+	hwlat_sample_window = tracefs_create_file("window", TRACE_MODE_WRITE,
 						  top_dir,
 						  &hwlat_window,
 						  &trace_min_max_fops);
 	if (!hwlat_sample_window)
 		goto err;
 
-	hwlat_sample_width = tracefs_create_file("width", 0644,
+	hwlat_sample_width = tracefs_create_file("width", TRACE_MODE_WRITE,
 						 top_dir,
 						 &hwlat_width,
 						 &trace_min_max_fops);
 	if (!hwlat_sample_width)
 		goto err;
 
-	hwlat_thread_mode = trace_create_file("mode", 0644,
+	hwlat_thread_mode = trace_create_file("mode", TRACE_MODE_WRITE,
 					      top_dir,
 					      NULL,
 					      &thread_mode_fops);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_irqsoff.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_irqsoff.c
@@ -231,7 +231,6 @@
 {
 	if (is_graph(iter->tr))
 		graph_trace_open(iter);
-
 }
 
 static void irqsoff_trace_close(struct trace_iterator *iter)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_kprobe.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_kprobe.c
@@ -19,6 +19,7 @@
 #include "trace_kprobe_selftest.h"
 #include "trace_probe.h"
 #include "trace_probe_tmpl.h"
+#include "trace_probe_kernel.h"
 
 #define KPROBE_EVENT_SYSTEM "kprobes"
 #define KRETPROBE_MAXACTIVE_MAX 4096
@@ -31,7 +32,7 @@
 	strlcpy(kprobe_boot_events_buf, str, COMMAND_LINE_SIZE);
 	disable_tracing_selftest("running kprobe events");
 
-	return 0;
+	return 1;
 }
 __setup("kprobe_event=", set_kprobe_boot_events);
 
@@ -704,9 +705,41 @@
 
 static struct notifier_block trace_kprobe_module_nb = {
 	.notifier_call = trace_kprobe_module_callback,
-	.priority = 1	/* Invoked after kprobe module callback */
+	.priority = 2	/* Invoked after kprobe and jump_label module callback */
+};
+
+struct count_symbols_struct {
+	const char *func_name;
+	unsigned int count;
 };
 
+static int count_symbols(void *data, const char *name, struct module *unused0,
+			 unsigned long unused1)
+{
+	struct count_symbols_struct *args = data;
+
+	if (strcmp(args->func_name, name))
+		return 0;
+
+	args->count++;
+
+	return 0;
+}
+
+static unsigned int number_of_same_symbols(char *func_name)
+{
+	struct count_symbols_struct args = {
+		.func_name = func_name,
+		.count = 0,
+	};
+
+	kallsyms_on_each_symbol(count_symbols, &args);
+
+	module_kallsyms_on_each_symbol(count_symbols, &args);
+
+	return args.count;
+}
+
 static int __trace_kprobe_create(int argc, const char *argv[])
 {
 	/*
@@ -835,6 +868,31 @@
 		}
 	}
 
+	if (symbol && !strchr(symbol, ':')) {
+		unsigned int count;
+
+		count = number_of_same_symbols(symbol);
+		if (count > 1) {
+			/*
+			 * Users should use ADDR to remove the ambiguity of
+			 * using KSYM only.
+			 */
+			trace_probe_log_err(0, NON_UNIQ_SYMBOL);
+			ret = -EADDRNOTAVAIL;
+
+			goto error;
+		} else if (count == 0) {
+			/*
+			 * We can return ENOENT earlier than when register the
+			 * kprobe.
+			 */
+			trace_probe_log_err(0, BAD_PROBE_ADDR);
+			ret = -ENOENT;
+
+			goto error;
+		}
+	}
+
 	trace_probe_log_set_index(0);
 	if (event) {
 		ret = traceprobe_parse_event_name(&event, &group, buf,
@@ -941,10 +999,10 @@
 /**
  * __kprobe_event_gen_cmd_start - Generate a kprobe event command from arg list
  * @cmd: A pointer to the dynevent_cmd struct representing the new event
+ * @kretprobe: Is this a return probe?
  * @name: The name of the kprobe event
  * @loc: The location of the kprobe event
- * @kretprobe: Is this a return probe?
- * @args: Variable number of arg (pairs), one pair for each field
+ * @...: Variable number of arg (pairs), one pair for each field
  *
  * NOTE: Users normally won't want to call this function directly, but
  * rather use the kprobe_event_gen_cmd_start() wrapper, which automatically
@@ -1017,7 +1075,7 @@
 /**
  * __kprobe_event_add_fields - Add probe fields to a kprobe command from arg list
  * @cmd: A pointer to the dynevent_cmd struct representing the new event
- * @args: Variable number of arg (pairs), one pair for each field
+ * @...: Variable number of arg (pairs), one pair for each field
  *
  * NOTE: Users normally won't want to call this function directly, but
  * rather use the kprobe_event_add_fields() wrapper, which
@@ -1175,15 +1233,18 @@
 {
 	struct dyn_event *ev = v;
 	struct trace_kprobe *tk;
+	unsigned long nmissed;
 
 	if (!is_trace_kprobe(ev))
 		return 0;
 
 	tk = to_trace_kprobe(ev);
+	nmissed = trace_kprobe_is_return(tk) ?
+		tk->rp.kp.nmissed + tk->rp.nmissed : tk->rp.kp.nmissed;
 	seq_printf(m, "  %-44s %15lu %15lu\n",
 		   trace_probe_name(&tk->tp),
 		   trace_kprobe_nhit(tk),
-		   tk->rp.kp.nmissed);
+		   nmissed);
 
 	return 0;
 }
@@ -1220,29 +1281,14 @@
 static nokprobe_inline int
 fetch_store_strlen_user(unsigned long addr)
 {
-	const void __user *uaddr =  (__force const void __user *)addr;
-
-	return strnlen_user_nofault(uaddr, MAX_STRING_SIZE);
+	return kern_fetch_store_strlen_user(addr);
 }
 
 /* Return the length of string -- including null terminal byte */
 static nokprobe_inline int
 fetch_store_strlen(unsigned long addr)
 {
-	int ret, len = 0;
-	u8 c;
-
-#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
-	if (addr < TASK_SIZE)
-		return fetch_store_strlen_user(addr);
-#endif
-
-	do {
-		ret = copy_from_kernel_nofault(&c, (u8 *)addr + len, 1);
-		len++;
-	} while (c && ret == 0 && len < MAX_STRING_SIZE);
-
-	return (ret < 0) ? ret : len;
+	return kern_fetch_store_strlen(addr);
 }
 
 /*
@@ -1252,21 +1298,7 @@
 static nokprobe_inline int
 fetch_store_string_user(unsigned long addr, void *dest, void *base)
 {
-	const void __user *uaddr =  (__force const void __user *)addr;
-	int maxlen = get_loc_len(*(u32 *)dest);
-	void *__dest;
-	long ret;
-
-	if (unlikely(!maxlen))
-		return -ENOMEM;
-
-	__dest = get_loc_data(dest, base);
-
-	ret = strncpy_from_user_nofault(__dest, uaddr, maxlen);
-	if (ret >= 0)
-		*(u32 *)dest = make_data_loc(ret, __dest - base);
-
-	return ret;
+	return kern_fetch_store_string_user(addr, dest, base);
 }
 
 /*
@@ -1276,29 +1308,7 @@
 static nokprobe_inline int
 fetch_store_string(unsigned long addr, void *dest, void *base)
 {
-	int maxlen = get_loc_len(*(u32 *)dest);
-	void *__dest;
-	long ret;
-
-#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
-	if ((unsigned long)addr < TASK_SIZE)
-		return fetch_store_string_user(addr, dest, base);
-#endif
-
-	if (unlikely(!maxlen))
-		return -ENOMEM;
-
-	__dest = get_loc_data(dest, base);
-
-	/*
-	 * Try to get string again, since the string can be changed while
-	 * probing.
-	 */
-	ret = strncpy_from_kernel_nofault(__dest, (void *)addr, maxlen);
-	if (ret >= 0)
-		*(u32 *)dest = make_data_loc(ret, __dest - base);
-
-	return ret;
+	return kern_fetch_store_string(addr, dest, base);
 }
 
 static nokprobe_inline int
@@ -1730,8 +1740,17 @@
 kretprobe_dispatcher(struct kretprobe_instance *ri, struct pt_regs *regs)
 {
 	struct kretprobe *rp = get_kretprobe(ri);
-	struct trace_kprobe *tk = container_of(rp, struct trace_kprobe, rp);
+	struct trace_kprobe *tk;
 
+	/*
+	 * There is a small chance that get_kretprobe(ri) returns NULL when
+	 * the kretprobe is unregister on another CPU between kretprobe's
+	 * trampoline_handler and this function.
+	 */
+	if (unlikely(!rp))
+		return 0;
+
+	tk = container_of(rp, struct trace_kprobe, rp);
 	raw_cpu_inc(*tk->nhit);
 
 	if (trace_probe_test_flag(&tk->tp, TP_FLAG_TRACE))
@@ -1793,6 +1812,7 @@
 }
 
 #ifdef CONFIG_PERF_EVENTS
+
 /* create a trace_kprobe, but don't add it to global lists */
 struct trace_event_call *
 create_local_trace_kprobe(char *func, void *addr, unsigned long offs,
@@ -1803,6 +1823,24 @@
 	int ret;
 	char *event;
 
+	if (func && !strchr(func, ':')) {
+		unsigned int count;
+
+		count = number_of_same_symbols(func);
+		if (count > 1)
+			/*
+			 * Users should use addr to remove the ambiguity of
+			 * using func only.
+			 */
+			return ERR_PTR(-EADDRNOTAVAIL);
+		else if (count == 0)
+			/*
+			 * We can return ENOENT earlier than when register the
+			 * kprobe.
+			 */
+			return ERR_PTR(-ENOENT);
+	}
+
 	/*
 	 * local trace_kprobes are not added to dyn_event, so they are never
 	 * searched in find_trace_kprobe(). Therefore, there is no concern of
@@ -1925,16 +1963,16 @@
 	if (ret)
 		return 0;
 
-	entry = tracefs_create_file("kprobe_events", 0644, NULL,
-				    NULL, &kprobe_events_ops);
+	entry = tracefs_create_file("kprobe_events", TRACE_MODE_WRITE,
+				    NULL, NULL, &kprobe_events_ops);
 
 	/* Event list interface */
 	if (!entry)
 		pr_warn("Could not create tracefs 'kprobe_events' entry\n");
 
 	/* Profile interface */
-	entry = tracefs_create_file("kprobe_profile", 0444, NULL,
-				    NULL, &kprobe_profile_ops);
+	entry = tracefs_create_file("kprobe_profile", TRACE_MODE_READ,
+				    NULL, NULL, &kprobe_profile_ops);
 
 	if (!entry)
 		pr_warn("Could not create tracefs 'kprobe_profile' entry\n");
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_osnoise.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_osnoise.c
@@ -730,7 +730,7 @@
 void osnoise_trace_irq_exit(int id, const char *desc)
 {
 	struct osnoise_variables *osn_var = this_cpu_osn_var();
-	int duration;
+	s64 duration;
 
 	if (!osn_var->sampling)
 		return;
@@ -861,7 +861,7 @@
 static void trace_softirq_exit_callback(void *data, unsigned int vec_nr)
 {
 	struct osnoise_variables *osn_var = this_cpu_osn_var();
-	int duration;
+	s64 duration;
 
 	if (!osn_var->sampling)
 		return;
@@ -969,7 +969,7 @@
 static void
 thread_exit(struct osnoise_variables *osn_var, struct task_struct *t)
 {
-	int duration;
+	s64 duration;
 
 	if (!osn_var->sampling)
 		return;
@@ -1196,6 +1196,26 @@
 		}
 
 		/*
+		 * In some cases, notably when running on a nohz_full CPU with
+		 * a stopped tick PREEMPT_RCU has no way to account for QSs.
+		 * This will eventually cause unwarranted noise as PREEMPT_RCU
+		 * will force preemption as the means of ending the current
+		 * grace period. We avoid this problem by calling
+		 * rcu_momentary_dyntick_idle(), which performs a zero duration
+		 * EQS allowing PREEMPT_RCU to end the current grace period.
+		 * This call shouldn't be wrapped inside an RCU critical
+		 * section.
+		 *
+		 * Note that in non PREEMPT_RCU kernels QSs are handled through
+		 * cond_resched()
+		 */
+		if (IS_ENABLED(CONFIG_PREEMPT_RCU)) {
+			local_irq_disable();
+			rcu_momentary_dyntick_idle();
+			local_irq_enable();
+		}
+
+		/*
 		 * For the non-preemptive kernel config: let threads runs, if
 		 * they so wish.
 		 */
@@ -1250,6 +1270,37 @@
 static struct cpumask save_cpumask;
 
 /*
+ * osnoise_sleep - sleep until the next period
+ */
+static void osnoise_sleep(void)
+{
+	u64 interval;
+	ktime_t wake_time;
+
+	mutex_lock(&interface_lock);
+	interval = osnoise_data.sample_period - osnoise_data.sample_runtime;
+	mutex_unlock(&interface_lock);
+
+	/*
+	 * differently from hwlat_detector, the osnoise tracer can run
+	 * without a pause because preemption is on.
+	 */
+	if (!interval) {
+		/* Let synchronize_rcu_tasks() make progress */
+		cond_resched_tasks_rcu_qs();
+		return;
+	}
+
+	wake_time = ktime_add_us(ktime_get(), interval);
+	__set_current_state(TASK_INTERRUPTIBLE);
+
+	while (schedule_hrtimeout_range(&wake_time, 0, HRTIMER_MODE_ABS)) {
+		if (kthread_should_stop())
+			break;
+	}
+}
+
+/*
  * osnoise_main - The osnoise detection kernel thread
  *
  * Calls run_osnoise() function to measure the osnoise for the configured runtime,
@@ -1257,30 +1308,10 @@
  */
 static int osnoise_main(void *data)
 {
-	u64 interval;
 
 	while (!kthread_should_stop()) {
-
 		run_osnoise();
-
-		mutex_lock(&interface_lock);
-		interval = osnoise_data.sample_period - osnoise_data.sample_runtime;
-		mutex_unlock(&interface_lock);
-
-		do_div(interval, USEC_PER_MSEC);
-
-		/*
-		 * differently from hwlat_detector, the osnoise tracer can run
-		 * without a pause because preemption is on.
-		 */
-		if (interval < 1) {
-			/* Let synchronize_rcu_tasks() make progress */
-			cond_resched_tasks_rcu_qs();
-			continue;
-		}
-
-		if (msleep_interruptible(interval))
-			break;
+		osnoise_sleep();
 	}
 
 	return 0;
@@ -1529,7 +1560,6 @@
 
 	if (IS_ERR(kthread)) {
 		pr_err(BANNER "could not start sampling thread\n");
-		stop_per_cpu_kthreads();
 		return -ENOMEM;
 	}
 
@@ -1567,8 +1597,9 @@
 	for_each_cpu(cpu, current_mask) {
 		retval = start_kthread(cpu);
 		if (retval) {
+			cpus_read_unlock();
 			stop_per_cpu_kthreads();
-			break;
+			return retval;
 		}
 	}
 
@@ -1592,6 +1623,8 @@
 	mutex_lock(&interface_lock);
 	cpus_read_lock();
 
+	if (!cpu_online(cpu))
+		goto out_unlock;
 	if (!cpumask_test_cpu(cpu, &osnoise_cpumask))
 		goto out_unlock;
 
@@ -1856,38 +1889,38 @@
 	if (!top_dir)
 		return 0;
 
-	tmp = tracefs_create_file("period_us", 0640, top_dir,
+	tmp = tracefs_create_file("period_us", TRACE_MODE_WRITE, top_dir,
 				  &osnoise_period, &trace_min_max_fops);
 	if (!tmp)
 		goto err;
 
-	tmp = tracefs_create_file("runtime_us", 0644, top_dir,
+	tmp = tracefs_create_file("runtime_us", TRACE_MODE_WRITE, top_dir,
 				  &osnoise_runtime, &trace_min_max_fops);
 	if (!tmp)
 		goto err;
 
-	tmp = tracefs_create_file("stop_tracing_us", 0640, top_dir,
+	tmp = tracefs_create_file("stop_tracing_us", TRACE_MODE_WRITE, top_dir,
 				  &osnoise_stop_tracing_in, &trace_min_max_fops);
 	if (!tmp)
 		goto err;
 
-	tmp = tracefs_create_file("stop_tracing_total_us", 0640, top_dir,
+	tmp = tracefs_create_file("stop_tracing_total_us", TRACE_MODE_WRITE, top_dir,
 				  &osnoise_stop_tracing_total, &trace_min_max_fops);
 	if (!tmp)
 		goto err;
 
-	tmp = trace_create_file("cpus", 0644, top_dir, NULL, &cpus_fops);
+	tmp = trace_create_file("cpus", TRACE_MODE_WRITE, top_dir, NULL, &cpus_fops);
 	if (!tmp)
 		goto err;
 #ifdef CONFIG_TIMERLAT_TRACER
 #ifdef CONFIG_STACKTRACE
-	tmp = tracefs_create_file("print_stack", 0640, top_dir,
+	tmp = tracefs_create_file("print_stack", TRACE_MODE_WRITE, top_dir,
 				  &osnoise_print_stack, &trace_min_max_fops);
 	if (!tmp)
 		goto err;
 #endif
 
-	tmp = tracefs_create_file("timerlat_period_us", 0640, top_dir,
+	tmp = tracefs_create_file("timerlat_period_us", TRACE_MODE_WRITE, top_dir,
 				  &timerlat_period, &trace_min_max_fops);
 	if (!tmp)
 		goto err;
@@ -1932,6 +1965,13 @@
 	return -EINVAL;
 }
 
+static void osnoise_unhook_events(void)
+{
+	unhook_thread_events();
+	unhook_softirq_events();
+	unhook_irq_events();
+}
+
 static int __osnoise_tracer_start(struct trace_array *tr)
 {
 	int retval;
@@ -1949,7 +1989,14 @@
 
 	retval = start_per_cpu_kthreads(tr);
 	if (retval) {
-		unhook_irq_events();
+		trace_osnoise_callback_enabled = false;
+		/*
+		 * Make sure that ftrace_nmi_enter/exit() see
+		 * trace_osnoise_callback_enabled as false before continuing.
+		 */
+		barrier();
+
+		osnoise_unhook_events();
 		return retval;
 	}
 
@@ -1981,9 +2028,7 @@
 
 	stop_per_cpu_kthreads();
 
-	unhook_irq_events();
-	unhook_softirq_events();
-	unhook_thread_events();
+	osnoise_unhook_events();
 
 	osnoise_busy = false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_output.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_output.c
@@ -349,7 +349,7 @@
 #ifdef CONFIG_KRETPROBES
 static inline const char *kretprobed(const char *name)
 {
-	static const char tramp_name[] = "kretprobe_trampoline";
+	static const char tramp_name[] = "__kretprobe_trampoline";
 	int size = sizeof(tramp_name);
 
 	if (strncmp(tramp_name, name, size) == 0)
@@ -1569,7 +1569,7 @@
 	NULL
 };
 
-__init static int init_events(void)
+__init int init_events(void)
 {
 	struct trace_event *event;
 	int i, ret;
@@ -1587,4 +1587,3 @@
 
 	return 0;
 }
-early_initcall(init_events);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_preemptirq.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_preemptirq.c
@@ -46,7 +46,7 @@
 		this_cpu_write(tracing_irq_cpu, 0);
 	}
 
-	lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+	lockdep_hardirqs_on_prepare();
 	lockdep_hardirqs_on(CALLER_ADDR0);
 }
 EXPORT_SYMBOL(trace_hardirqs_on);
@@ -94,15 +94,15 @@
 		this_cpu_write(tracing_irq_cpu, 0);
 	}
 
-	lockdep_hardirqs_on_prepare(CALLER_ADDR0);
-	lockdep_hardirqs_on(CALLER_ADDR0);
+	lockdep_hardirqs_on_prepare();
+	lockdep_hardirqs_on(caller_addr);
 }
 EXPORT_SYMBOL(trace_hardirqs_on_caller);
 NOKPROBE_SYMBOL(trace_hardirqs_on_caller);
 
 __visible void trace_hardirqs_off_caller(unsigned long caller_addr)
 {
-	lockdep_hardirqs_off(CALLER_ADDR0);
+	lockdep_hardirqs_off(caller_addr);
 
 	if (!this_cpu_read(tracing_irq_cpu)) {
 		this_cpu_write(tracing_irq_cpu, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_printk.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_printk.c
@@ -384,7 +384,7 @@
 	if (ret)
 		return 0;
 
-	trace_create_file("printk_formats", 0444, NULL,
+	trace_create_file("printk_formats", TRACE_MODE_READ, NULL,
 				    NULL, &ftrace_formats_fops);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_probe.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_probe.c
@@ -64,7 +64,7 @@
 	int len = *(u32 *)data >> 16;
 
 	if (!len)
-		trace_seq_puts(s, "(fault)");
+		trace_seq_puts(s, FAULT_STRING);
 	else
 		trace_seq_printf(s, "\"%s\"",
 				 (const char *)get_loc_data(data, ent));
@@ -76,9 +76,11 @@
 /* Fetch type information table */
 static const struct fetch_type probe_fetch_types[] = {
 	/* Special types */
-	__ASSIGN_FETCH_TYPE("string", string, string, sizeof(u32), 1,
+	__ASSIGN_FETCH_TYPE("string", string, string, sizeof(u32), 1, 1,
 			    "__data_loc char[]"),
-	__ASSIGN_FETCH_TYPE("ustring", string, string, sizeof(u32), 1,
+	__ASSIGN_FETCH_TYPE("ustring", string, string, sizeof(u32), 1, 1,
+			    "__data_loc char[]"),
+	__ASSIGN_FETCH_TYPE("symstr", string, string, sizeof(u32), 1, 1,
 			    "__data_loc char[]"),
 	/* Basic types */
 	ASSIGN_FETCH_TYPE(u8,  u8,  0),
@@ -246,7 +248,7 @@
 			return -EINVAL;
 		}
 		strlcpy(buf, event, slash - event + 1);
-		if (!is_good_name(buf)) {
+		if (!is_good_system_name(buf)) {
 			trace_probe_log_err(offset, BAD_GROUP_NAME);
 			return -EINVAL;
 		}
@@ -259,7 +261,7 @@
 	if (len == 0) {
 		trace_probe_log_err(offset, NO_EVENT_NAME);
 		return -EINVAL;
-	} else if (len > MAX_EVENT_NAME_LEN) {
+	} else if (len >= MAX_EVENT_NAME_LEN) {
 		trace_probe_log_err(offset, EVENT_TOO_LONG);
 		return -EINVAL;
 	}
@@ -279,7 +281,14 @@
 	int ret = 0;
 	int len;
 
-	if (strcmp(arg, "retval") == 0) {
+	if (flags & TPARG_FL_TPOINT) {
+		if (code->data)
+			return -EFAULT;
+		code->data = kstrdup(arg, GFP_KERNEL);
+		if (!code->data)
+			return -ENOMEM;
+		code->op = FETCH_OP_TP_ARG;
+	} else if (strcmp(arg, "retval") == 0) {
 		if (flags & TPARG_FL_RETURN) {
 			code->op = FETCH_OP_RETVAL;
 		} else {
@@ -303,7 +312,7 @@
 			}
 		} else
 			goto inval_var;
-	} else if (strcmp(arg, "comm") == 0) {
+	} else if (strcmp(arg, "comm") == 0 || strcmp(arg, "COMM") == 0) {
 		code->op = FETCH_OP_COMM;
 #ifdef CONFIG_HAVE_FUNCTION_ARG_ACCESS_API
 	} else if (((flags & TPARG_FL_MASK) ==
@@ -319,13 +328,6 @@
 		code->op = FETCH_OP_ARG;
 		code->param = (unsigned int)param - 1;
 #endif
-	} else if (flags & TPARG_FL_TPOINT) {
-		if (code->data)
-			return -EFAULT;
-		code->data = kstrdup(arg, GFP_KERNEL);
-		if (!code->data)
-			return -ENOMEM;
-		code->op = FETCH_OP_TP_ARG;
 	} else
 		goto inval_var;
 
@@ -356,6 +358,8 @@
 		return -EINVAL;
 	}
 	*pbuf = kstrndup(str, len - 1, GFP_KERNEL);
+	if (!*pbuf)
+		return -ENOMEM;
 	return 0;
 }
 
@@ -378,6 +382,11 @@
 		break;
 
 	case '%':	/* named register */
+		if (flags & TPARG_FL_TPOINT) {
+			/* eprobes do not handle registers */
+			trace_probe_log_err(offs, BAD_VAR);
+			break;
+		}
 		ret = regs_query_register_offset(arg + 1);
 		if (ret >= 0) {
 			code->op = FETCH_OP_REG;
@@ -611,9 +620,11 @@
 
 	/*
 	 * Since $comm and immediate string can not be dereferenced,
-	 * we can find those by strcmp.
+	 * we can find those by strcmp. But ignore for eprobes.
 	 */
-	if (strcmp(arg, "$comm") == 0 || strncmp(arg, "\\\"", 2) == 0) {
+	if (!(flags & TPARG_FL_TPOINT) &&
+	    (strcmp(arg, "$comm") == 0 || strcmp(arg, "$COMM") == 0 ||
+	     strncmp(arg, "\\\"", 2) == 0)) {
 		/* The type of $comm must be "string", and not an array. */
 		if (parg->count || (t && strcmp(t, "string")))
 			goto out;
@@ -649,16 +660,26 @@
 
 	ret = -EINVAL;
 	/* Store operation */
-	if (!strcmp(parg->type->name, "string") ||
-	    !strcmp(parg->type->name, "ustring")) {
-		if (code->op != FETCH_OP_DEREF && code->op != FETCH_OP_UDEREF &&
-		    code->op != FETCH_OP_IMM && code->op != FETCH_OP_COMM &&
-		    code->op != FETCH_OP_DATA && code->op != FETCH_OP_TP_ARG) {
-			trace_probe_log_err(offset + (t ? (t - arg) : 0),
-					    BAD_STRING);
-			goto fail;
+	if (parg->type->is_string) {
+		if (!strcmp(parg->type->name, "symstr")) {
+			if (code->op != FETCH_OP_REG && code->op != FETCH_OP_STACK &&
+			    code->op != FETCH_OP_RETVAL && code->op != FETCH_OP_ARG &&
+			    code->op != FETCH_OP_DEREF && code->op != FETCH_OP_TP_ARG) {
+				trace_probe_log_err(offset + (t ? (t - arg) : 0),
+						    BAD_SYMSTRING);
+				goto fail;
+			}
+		} else {
+			if (code->op != FETCH_OP_DEREF && code->op != FETCH_OP_UDEREF &&
+			    code->op != FETCH_OP_IMM && code->op != FETCH_OP_COMM &&
+			    code->op != FETCH_OP_DATA && code->op != FETCH_OP_TP_ARG) {
+				trace_probe_log_err(offset + (t ? (t - arg) : 0),
+						    BAD_STRING);
+				goto fail;
+			}
 		}
-		if ((code->op == FETCH_OP_IMM || code->op == FETCH_OP_COMM ||
+		if (!strcmp(parg->type->name, "symstr") ||
+		    (code->op == FETCH_OP_IMM || code->op == FETCH_OP_COMM ||
 		     code->op == FETCH_OP_DATA) || code->op == FETCH_OP_TP_ARG ||
 		     parg->count) {
 			/*
@@ -666,6 +687,8 @@
 			 * must be kept, and if parg->count != 0, this is an
 			 * array of string pointers instead of string address
 			 * itself.
+			 * For the symstr, it doesn't need to dereference, thus
+			 * it just get the value.
 			 */
 			code++;
 			if (code->op != FETCH_OP_NOP) {
@@ -677,6 +700,8 @@
 		if (!strcmp(parg->type->name, "ustring") ||
 		    code->op == FETCH_OP_UDEREF)
 			code->op = FETCH_OP_ST_USTRING;
+		else if (!strcmp(parg->type->name, "symstr"))
+			code->op = FETCH_OP_ST_SYMSTR;
 		else
 			code->op = FETCH_OP_ST_STRING;
 		code->size = parg->type->size;
@@ -906,8 +931,7 @@
 	for (i = 0; i < tp->nr_args; i++) {
 		parg = tp->args + i;
 		if (parg->count) {
-			if ((strcmp(parg->type->name, "string") == 0) ||
-			    (strcmp(parg->type->name, "ustring") == 0))
+			if (parg->type->is_string)
 				fmt = ", __get_str(%s[%d])";
 			else
 				fmt = ", REC->%s[%d]";
@@ -915,8 +939,7 @@
 				pos += snprintf(buf + pos, LEN_OR_ZERO,
 						fmt, parg->name, j);
 		} else {
-			if ((strcmp(parg->type->name, "string") == 0) ||
-			    (strcmp(parg->type->name, "ustring") == 0))
+			if (parg->type->is_string)
 				fmt = ", __get_str(%s)";
 			else
 				fmt = ", REC->%s";
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_probe.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_probe.h
@@ -99,6 +99,7 @@
 	FETCH_OP_ST_UMEM,	/* Mem: .offset, .size */
 	FETCH_OP_ST_STRING,	/* String: .offset, .size */
 	FETCH_OP_ST_USTRING,	/* User String: .offset, .size */
+	FETCH_OP_ST_SYMSTR,	/* Kernel Symbol String: .offset, .size */
 	// Stage 4 (modify) op
 	FETCH_OP_MOD_BF,	/* Bitfield: .basesize, .lshift, .rshift */
 	// Stage 5 (loop) op
@@ -134,7 +135,8 @@
 struct fetch_type {
 	const char		*name;		/* Name of type */
 	size_t			size;		/* Byte size of type */
-	int			is_signed;	/* Signed flag */
+	bool			is_signed;	/* Signed flag */
+	bool			is_string;	/* String flag */
 	print_type_func_t	print;		/* Print functions */
 	const char		*fmt;		/* Format string */
 	const char		*fmttype;	/* Name in format file */
@@ -178,16 +180,19 @@
 #define _ADDR_FETCH_TYPE(t) __ADDR_FETCH_TYPE(t)
 #define ADDR_FETCH_TYPE _ADDR_FETCH_TYPE(BITS_PER_LONG)
 
-#define __ASSIGN_FETCH_TYPE(_name, ptype, ftype, _size, sign, _fmttype)	\
-	{.name = _name,				\
+#define __ASSIGN_FETCH_TYPE(_name, ptype, ftype, _size, sign, str, _fmttype)	\
+	{.name = _name,					\
 	 .size = _size,					\
-	 .is_signed = sign,				\
+	 .is_signed = (bool)sign,			\
+	 .is_string = (bool)str,			\
 	 .print = PRINT_TYPE_FUNC_NAME(ptype),		\
 	 .fmt = PRINT_TYPE_FMT_NAME(ptype),		\
 	 .fmttype = _fmttype,				\
 	}
+
+/* Non string types can use these macros */
 #define _ASSIGN_FETCH_TYPE(_name, ptype, ftype, _size, sign, _fmttype)	\
-	__ASSIGN_FETCH_TYPE(_name, ptype, ftype, _size, sign, #_fmttype)
+	__ASSIGN_FETCH_TYPE(_name, ptype, ftype, _size, sign, 0, #_fmttype)
 #define ASSIGN_FETCH_TYPE(ptype, ftype, sign)			\
 	_ASSIGN_FETCH_TYPE(#ptype, ptype, ftype, sizeof(ftype), sign, ptype)
 
@@ -303,7 +308,7 @@
 {
 	struct trace_probe_event *tpe = trace_probe_event_from_call(call);
 
-	return list_first_entry(&tpe->probes, struct trace_probe, list);
+	return list_first_entry_or_null(&tpe->probes, struct trace_probe, list);
 }
 
 static inline struct list_head *trace_probe_probe_list(struct trace_probe *tp)
@@ -400,6 +405,7 @@
 	C(BAD_MAXACT,		"Invalid maxactive number"),		\
 	C(MAXACT_TOO_BIG,	"Maxactive is too big"),		\
 	C(BAD_PROBE_ADDR,	"Invalid probed address or symbol"),	\
+	C(NON_UNIQ_SYMBOL,	"The symbol is not unique"),		\
 	C(BAD_RETPROBE,		"Retprobe address must be an function entry"), \
 	C(BAD_ADDR_SUFFIX,	"Invalid probed address suffix"), \
 	C(NO_GROUP_NAME,	"Group name is not specified"),		\
@@ -432,6 +438,7 @@
 	C(ARRAY_TOO_BIG,	"Array number is too big"),		\
 	C(BAD_TYPE,		"Unknown type is specified"),		\
 	C(BAD_STRING,		"String accepts only memory argument"),	\
+	C(BAD_SYMSTRING,	"Symbol String doesn't accept data/userdata"),	\
 	C(BAD_BITFIELD,		"Invalid bitfield"),			\
 	C(ARG_NAME_TOO_LONG,	"Argument name is too long"),		\
 	C(NO_ARG_NAME,		"Argument name is not specified"),	\
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_probe_kernel.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_probe_kernel.h
@@ -0,0 +1,101 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __TRACE_PROBE_KERNEL_H_
+#define __TRACE_PROBE_KERNEL_H_
+
+/*
+ * This depends on trace_probe.h, but can not include it due to
+ * the way trace_probe_tmpl.h is used by trace_kprobe.c and trace_eprobe.c.
+ * Which means that any other user must include trace_probe.h before including
+ * this file.
+ */
+/* Return the length of string -- including null terminal byte */
+static nokprobe_inline int
+kern_fetch_store_strlen_user(unsigned long addr)
+{
+	const void __user *uaddr =  (__force const void __user *)addr;
+
+	return strnlen_user_nofault(uaddr, MAX_STRING_SIZE);
+}
+
+/* Return the length of string -- including null terminal byte */
+static nokprobe_inline int
+kern_fetch_store_strlen(unsigned long addr)
+{
+	int ret, len = 0;
+	u8 c;
+
+#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
+	if (addr < TASK_SIZE)
+		return kern_fetch_store_strlen_user(addr);
+#endif
+
+	do {
+		ret = copy_from_kernel_nofault(&c, (u8 *)addr + len, 1);
+		len++;
+	} while (c && ret == 0 && len < MAX_STRING_SIZE);
+
+	return (ret < 0) ? ret : len;
+}
+
+static nokprobe_inline void set_data_loc(int ret, void *dest, void *__dest, void *base)
+{
+	if (ret < 0)
+		ret = 0;
+	*(u32 *)dest = make_data_loc(ret, __dest - base);
+}
+
+/*
+ * Fetch a null-terminated string from user. Caller MUST set *(u32 *)buf
+ * with max length and relative data location.
+ */
+static nokprobe_inline int
+kern_fetch_store_string_user(unsigned long addr, void *dest, void *base)
+{
+	const void __user *uaddr =  (__force const void __user *)addr;
+	int maxlen = get_loc_len(*(u32 *)dest);
+	void *__dest;
+	long ret;
+
+	if (unlikely(!maxlen))
+		return -ENOMEM;
+
+	__dest = get_loc_data(dest, base);
+
+	ret = strncpy_from_user_nofault(__dest, uaddr, maxlen);
+	set_data_loc(ret, dest, __dest, base);
+
+	return ret;
+}
+
+/*
+ * Fetch a null-terminated string. Caller MUST set *(u32 *)buf with max
+ * length and relative data location.
+ */
+static nokprobe_inline int
+kern_fetch_store_string(unsigned long addr, void *dest, void *base)
+{
+	int maxlen = get_loc_len(*(u32 *)dest);
+	void *__dest;
+	long ret;
+
+#ifdef CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
+	if ((unsigned long)addr < TASK_SIZE)
+		return kern_fetch_store_string_user(addr, dest, base);
+#endif
+
+	if (unlikely(!maxlen))
+		return -ENOMEM;
+
+	__dest = get_loc_data(dest, base);
+
+	/*
+	 * Try to get string again, since the string can be changed while
+	 * probing.
+	 */
+	ret = strncpy_from_kernel_nofault(__dest, (void *)addr, maxlen);
+	set_data_loc(ret, dest, __dest, base);
+
+	return ret;
+}
+
+#endif /* __TRACE_PROBE_KERNEL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_probe_tmpl.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_probe_tmpl.h
@@ -67,6 +67,37 @@
 static nokprobe_inline int
 probe_mem_read_user(void *dest, void *src, size_t size);
 
+static nokprobe_inline int
+fetch_store_symstrlen(unsigned long addr)
+{
+	char namebuf[KSYM_SYMBOL_LEN];
+	int ret;
+
+	ret = sprint_symbol(namebuf, addr);
+	if (ret < 0)
+		return 0;
+
+	return ret + 1;
+}
+
+/*
+ * Fetch a null-terminated symbol string + offset. Caller MUST set *(u32 *)buf
+ * with max length and relative data location.
+ */
+static nokprobe_inline int
+fetch_store_symstring(unsigned long addr, void *dest, void *base)
+{
+	int maxlen = get_loc_len(*(u32 *)dest);
+	void *__dest;
+
+	if (unlikely(!maxlen))
+		return -ENOMEM;
+
+	__dest = get_loc_data(dest, base);
+
+	return sprint_symbol(__dest, addr);
+}
+
 /* From the 2nd stage, routine is same */
 static nokprobe_inline int
 process_fetch_insn_bottom(struct fetch_insn *code, unsigned long val,
@@ -99,16 +130,22 @@
 stage3:
 	/* 3rd stage: store value to buffer */
 	if (unlikely(!dest)) {
-		if (code->op == FETCH_OP_ST_STRING) {
+		switch (code->op) {
+		case FETCH_OP_ST_STRING:
 			ret = fetch_store_strlen(val + code->offset);
 			code++;
 			goto array;
-		} else if (code->op == FETCH_OP_ST_USTRING) {
-			ret += fetch_store_strlen_user(val + code->offset);
+		case FETCH_OP_ST_USTRING:
+			ret = fetch_store_strlen_user(val + code->offset);
 			code++;
 			goto array;
-		} else
+		case FETCH_OP_ST_SYMSTR:
+			ret = fetch_store_symstrlen(val + code->offset);
+			code++;
+			goto array;
+		default:
 			return -EILSEQ;
+		}
 	}
 
 	switch (code->op) {
@@ -129,6 +166,10 @@
 		loc = *(u32 *)dest;
 		ret = fetch_store_string_user(val + code->offset, dest, base);
 		break;
+	case FETCH_OP_ST_SYMSTR:
+		loc = *(u32 *)dest;
+		ret = fetch_store_symstring(val + code->offset, dest, base);
+		break;
 	default:
 		return -EILSEQ;
 	}
@@ -143,6 +184,8 @@
 array:
 	/* the last stage: Loop on array */
 	if (code->op == FETCH_OP_LP_ARRAY) {
+		if (ret < 0)
+			ret = 0;
 		total += ret;
 		if (++i < code->param) {
 			code = s3;
@@ -204,9 +247,7 @@
 		if (unlikely(arg->dynamic))
 			*dl = make_data_loc(maxlen, dyndata - base);
 		ret = process_fetch_insn(arg->code, rec, dl, base);
-		if (unlikely(ret < 0 && arg->dynamic)) {
-			*dl = make_data_loc(0, dyndata - base);
-		} else {
+		if (arg->dynamic && likely(ret > 0)) {
 			dyndata += ret;
 			maxlen -= ret;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_recursion_record.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_recursion_record.c
@@ -226,8 +226,8 @@
 {
 	struct dentry *dentry;
 
-	dentry = trace_create_file("recursed_functions", 0644, NULL, NULL,
-				   &recursed_functions_fops);
+	dentry = trace_create_file("recursed_functions", TRACE_MODE_WRITE,
+				   NULL, NULL, &recursed_functions_fops);
 	if (!dentry)
 		pr_warn("WARNING: Failed to create recursed_functions\n");
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_stack.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_stack.c
@@ -559,14 +559,14 @@
 	if (ret)
 		return 0;
 
-	trace_create_file("stack_max_size", 0644, NULL,
+	trace_create_file("stack_max_size", TRACE_MODE_WRITE, NULL,
 			&stack_trace_max_size, &stack_max_size_fops);
 
-	trace_create_file("stack_trace", 0444, NULL,
+	trace_create_file("stack_trace", TRACE_MODE_READ, NULL,
 			NULL, &stack_trace_fops);
 
 #ifdef CONFIG_DYNAMIC_FTRACE
-	trace_create_file("stack_trace_filter", 0644, NULL,
+	trace_create_file("stack_trace_filter", TRACE_MODE_WRITE, NULL,
 			  &trace_ops, &stack_trace_filter_fops);
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_stat.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_stat.c
@@ -297,9 +297,9 @@
 	if (!stat_dir && (ret = tracing_stat_init()))
 		return ret;
 
-	session->file = tracefs_create_file(session->ts->name, 0644,
-					    stat_dir,
-					    session, &tracing_stat_fops);
+	session->file = tracefs_create_file(session->ts->name, TRACE_MODE_WRITE,
+					    stat_dir, session,
+					    &tracing_stat_fops);
 	if (!session->file)
 		return -ENOMEM;
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_synth.h
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_synth.h
@@ -18,6 +18,7 @@
 	bool is_signed;
 	bool is_string;
 	bool is_dynamic;
+	bool is_stack;
 };
 
 struct synth_event {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_syscalls.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_syscalls.c
@@ -154,7 +154,7 @@
 			goto end;
 
 		/* parameter types */
-		if (tr->trace_flags & TRACE_ITER_VERBOSE)
+		if (tr && tr->trace_flags & TRACE_ITER_VERBOSE)
 			trace_seq_printf(s, "%s ", entry->types[i]);
 
 		/* parameter values */
@@ -296,9 +296,7 @@
 	struct trace_event_file *trace_file;
 	struct syscall_trace_enter *entry;
 	struct syscall_metadata *sys_data;
-	struct ring_buffer_event *event;
-	struct trace_buffer *buffer;
-	unsigned int trace_ctx;
+	struct trace_event_buffer fbuffer;
 	unsigned long args[6];
 	int syscall_nr;
 	int size;
@@ -321,21 +319,16 @@
 
 	size = sizeof(*entry) + sizeof(unsigned long) * sys_data->nb_args;
 
-	trace_ctx = tracing_gen_ctx();
-
-	buffer = tr->array_buffer.buffer;
-	event = trace_buffer_lock_reserve(buffer,
-			sys_data->enter_event->event.type, size, trace_ctx);
-	if (!event)
+	entry = trace_event_buffer_reserve(&fbuffer, trace_file, size);
+	if (!entry)
 		return;
 
-	entry = ring_buffer_event_data(event);
+	entry = ring_buffer_event_data(fbuffer.event);
 	entry->nr = syscall_nr;
 	syscall_get_arguments(current, regs, args);
 	memcpy(entry->args, args, sizeof(unsigned long) * sys_data->nb_args);
 
-	event_trigger_unlock_commit(trace_file, buffer, event, entry,
-				    trace_ctx);
+	trace_event_buffer_commit(&fbuffer);
 }
 
 static void ftrace_syscall_exit(void *data, struct pt_regs *regs, long ret)
@@ -344,9 +337,7 @@
 	struct trace_event_file *trace_file;
 	struct syscall_trace_exit *entry;
 	struct syscall_metadata *sys_data;
-	struct ring_buffer_event *event;
-	struct trace_buffer *buffer;
-	unsigned int trace_ctx;
+	struct trace_event_buffer fbuffer;
 	int syscall_nr;
 
 	syscall_nr = trace_get_syscall_nr(current, regs);
@@ -365,21 +356,15 @@
 	if (!sys_data)
 		return;
 
-	trace_ctx = tracing_gen_ctx();
-
-	buffer = tr->array_buffer.buffer;
-	event = trace_buffer_lock_reserve(buffer,
-			sys_data->exit_event->event.type, sizeof(*entry),
-			trace_ctx);
-	if (!event)
+	entry = trace_event_buffer_reserve(&fbuffer, trace_file, sizeof(*entry));
+	if (!entry)
 		return;
 
-	entry = ring_buffer_event_data(event);
+	entry = ring_buffer_event_data(fbuffer.event);
 	entry->nr = syscall_nr;
 	entry->ret = syscall_get_return_value(current, regs);
 
-	event_trigger_unlock_commit(trace_file, buffer, event, entry,
-				    trace_ctx);
+	trace_event_buffer_commit(&fbuffer);
 }
 
 static int reg_event_syscall_enter(struct trace_event_file *file,
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/trace_uprobe.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/trace_uprobe.c
@@ -168,7 +168,8 @@
 			 */
 			ret++;
 		*(u32 *)dest = make_data_loc(ret, (void *)dst - base);
-	}
+	} else
+		*(u32 *)dest = make_data_loc(0, (void *)dst - base);
 
 	return ret;
 }
@@ -1313,6 +1314,7 @@
 		return 0;
 
 	list_for_each_entry(pos, trace_probe_probe_list(tp), list) {
+		tu = container_of(pos, struct trace_uprobe, tp);
 		err = uprobe_apply(tu->inode, tu->offset, &tu->consumer, true);
 		if (err) {
 			uprobe_perf_close(call, event);
@@ -1421,7 +1423,7 @@
 
 int bpf_get_uprobe_info(const struct perf_event *event, u32 *fd_type,
 			const char **filename, u64 *probe_offset,
-			bool perf_type_tracepoint)
+			u64 *probe_addr, bool perf_type_tracepoint)
 {
 	const char *pevent = trace_event_name(event->tp_event);
 	const char *group = event->tp_event->class->system;
@@ -1438,6 +1440,7 @@
 				    : BPF_FD_TYPE_UPROBE;
 	*filename = tu->filename;
 	*probe_offset = tu->offset;
+	*probe_addr = 0;
 	return 0;
 }
 #endif	/* CONFIG_PERF_EVENTS */
@@ -1618,6 +1621,11 @@
 	tu->path = path;
 	tu->ref_ctr_offset = ref_ctr_offset;
 	tu->filename = kstrdup(name, GFP_KERNEL);
+	if (!tu->filename) {
+		ret = -ENOMEM;
+		goto error;
+	}
+
 	init_trace_event_call(tu);
 
 	ptype = is_ret_probe(tu) ? PROBE_PRINT_RETURN : PROBE_PRINT_NORMAL;
@@ -1655,10 +1663,10 @@
 	if (ret)
 		return 0;
 
-	trace_create_file("uprobe_events", 0644, NULL,
+	trace_create_file("uprobe_events", TRACE_MODE_WRITE, NULL,
 				    NULL, &uprobe_events_ops);
 	/* Profile interface */
-	trace_create_file("uprobe_profile", 0444, NULL,
+	trace_create_file("uprobe_profile", TRACE_MODE_READ, NULL,
 				    NULL, &uprobe_profile_ops);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/trace/tracing_map.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/trace/tracing_map.c
@@ -15,6 +15,7 @@
 #include <linux/jhash.h>
 #include <linux/slab.h>
 #include <linux/sort.h>
+#include <linux/kmemleak.h>
 
 #include "tracing_map.h"
 #include "trace.h"
@@ -307,6 +308,7 @@
 	for (i = 0; i < a->n_pages; i++) {
 		if (!a->pages[i])
 			break;
+		kmemleak_free(a->pages[i]);
 		free_page((unsigned long)a->pages[i]);
 	}
 
@@ -342,6 +344,7 @@
 		a->pages[i] = (void *)get_zeroed_page(GFP_KERNEL);
 		if (!a->pages[i])
 			goto free;
+		kmemleak_alloc(a->pages[i], PAGE_SIZE, 1, GFP_KERNEL);
 	}
  out:
 	return a;
@@ -451,7 +454,7 @@
 	struct tracing_map_elt *elt = NULL;
 	int idx;
 
-	idx = atomic_inc_return(&map->next_elt);
+	idx = atomic_fetch_add_unless(&map->next_elt, 1, map->max_elts);
 	if (idx < map->max_elts) {
 		elt = *(TRACING_MAP_ELT(map->elts, idx));
 		if (map->ops && map->ops->elt_init)
@@ -571,7 +574,12 @@
 				}
 
 				memcpy(elt->key, key, map->key_size);
-				entry->val = elt;
+				/*
+				 * Ensure the initialization is visible and
+				 * publish the elt.
+				 */
+				smp_wmb();
+				WRITE_ONCE(entry->val, elt);
 				atomic64_inc(&map->hits);
 
 				return entry->val;
@@ -691,7 +699,7 @@
 {
 	unsigned int i;
 
-	atomic_set(&map->next_elt, -1);
+	atomic_set(&map->next_elt, 0);
 	atomic64_set(&map->hits, 0);
 	atomic64_set(&map->drops, 0);
 
@@ -775,7 +783,7 @@
 
 	map->map_bits = map_bits;
 	map->max_elts = (1 << map_bits);
-	atomic_set(&map->next_elt, -1);
+	atomic_set(&map->next_elt, 0);
 
 	map->map_size = (1 << (map_bits + 1));
 	map->ops = ops;
@@ -834,29 +842,31 @@
 	return err;
 }
 
-static int cmp_entries_dup(const struct tracing_map_sort_entry **a,
-			   const struct tracing_map_sort_entry **b)
+static int cmp_entries_dup(const void *A, const void *B)
 {
-	int ret = 0;
+	const struct tracing_map_sort_entry *a, *b;
 
-	if (memcmp((*a)->key, (*b)->key, (*a)->elt->map->key_size))
-		ret = 1;
+	a = *(const struct tracing_map_sort_entry **)A;
+	b = *(const struct tracing_map_sort_entry **)B;
 
-	return ret;
+	return memcmp(a->key, b->key, a->elt->map->key_size);
 }
 
-static int cmp_entries_sum(const struct tracing_map_sort_entry **a,
-			   const struct tracing_map_sort_entry **b)
+static int cmp_entries_sum(const void *A, const void *B)
 {
 	const struct tracing_map_elt *elt_a, *elt_b;
+	const struct tracing_map_sort_entry *a, *b;
 	struct tracing_map_sort_key *sort_key;
 	struct tracing_map_field *field;
 	tracing_map_cmp_fn_t cmp_fn;
 	void *val_a, *val_b;
 	int ret = 0;
 
-	elt_a = (*a)->elt;
-	elt_b = (*b)->elt;
+	a = *(const struct tracing_map_sort_entry **)A;
+	b = *(const struct tracing_map_sort_entry **)B;
+
+	elt_a = a->elt;
+	elt_b = b->elt;
 
 	sort_key = &elt_a->map->sort_key;
 
@@ -873,18 +883,21 @@
 	return ret;
 }
 
-static int cmp_entries_key(const struct tracing_map_sort_entry **a,
-			   const struct tracing_map_sort_entry **b)
+static int cmp_entries_key(const void *A, const void *B)
 {
 	const struct tracing_map_elt *elt_a, *elt_b;
+	const struct tracing_map_sort_entry *a, *b;
 	struct tracing_map_sort_key *sort_key;
 	struct tracing_map_field *field;
 	tracing_map_cmp_fn_t cmp_fn;
 	void *val_a, *val_b;
 	int ret = 0;
 
-	elt_a = (*a)->elt;
-	elt_b = (*b)->elt;
+	a = *(const struct tracing_map_sort_entry **)A;
+	b = *(const struct tracing_map_sort_entry **)B;
+
+	elt_a = a->elt;
+	elt_b = b->elt;
 
 	sort_key = &elt_a->map->sort_key;
 
@@ -989,10 +1002,8 @@
 			   struct tracing_map_sort_key *primary_key,
 			   struct tracing_map_sort_key *secondary_key)
 {
-	int (*primary_fn)(const struct tracing_map_sort_entry **,
-			  const struct tracing_map_sort_entry **);
-	int (*secondary_fn)(const struct tracing_map_sort_entry **,
-			    const struct tracing_map_sort_entry **);
+	int (*primary_fn)(const void *, const void *);
+	int (*secondary_fn)(const void *, const void *);
 	unsigned i, start = 0, n_sub = 1;
 
 	if (is_key(map, primary_key->field_idx))
@@ -1061,8 +1072,7 @@
 			     unsigned int n_sort_keys,
 			     struct tracing_map_sort_entry ***sort_entries)
 {
-	int (*cmp_entries_fn)(const struct tracing_map_sort_entry **,
-			      const struct tracing_map_sort_entry **);
+	int (*cmp_entries_fn)(const void *, const void *);
 	struct tracing_map_sort_entry *sort_entry, **entries;
 	int i, n_entries, ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/tsacct.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/tsacct.c
@@ -38,11 +38,10 @@
 	stats->ac_btime = clamp_t(time64_t, btime, 0, U32_MAX);
 	stats->ac_btime64 = btime;
 
-	if (thread_group_leader(tsk)) {
+	if (tsk->flags & PF_EXITING)
 		stats->ac_exitcode = tsk->exit_code;
-		if (tsk->flags & PF_FORKNOEXEC)
-			stats->ac_flag |= AFORK;
-	}
+	if (thread_group_leader(tsk) && (tsk->flags & PF_FORKNOEXEC))
+		stats->ac_flag |= AFORK;
 	if (tsk->flags & PF_SUPERPRIV)
 		stats->ac_flag |= ASU;
 	if (tsk->flags & PF_DUMPCORE)
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/ucount.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/ucount.c
@@ -184,6 +184,7 @@
 			kfree(new);
 		} else {
 			hlist_add_head(&new->node, hashent);
+			get_user_ns(new->ns);
 			spin_unlock_irq(&ucounts_lock);
 			return new;
 		}
@@ -204,6 +205,7 @@
 	if (atomic_dec_and_lock_irqsave(&ucounts->count, &ucounts_lock, flags)) {
 		hlist_del_init(&ucounts->node);
 		spin_unlock_irqrestore(&ucounts_lock, flags);
+		put_user_ns(ucounts->ns);
 		kfree(ucounts);
 	}
 }
@@ -258,15 +260,16 @@
 long inc_rlimit_ucounts(struct ucounts *ucounts, enum ucount_type type, long v)
 {
 	struct ucounts *iter;
+	long max = LONG_MAX;
 	long ret = 0;
 
 	for (iter = ucounts; iter; iter = iter->ns->ucounts) {
-		long max = READ_ONCE(iter->ns->ucount_max[type]);
 		long new = atomic_long_add_return(v, &iter->ucount[type]);
 		if (new < 0 || new > max)
 			ret = LONG_MAX;
 		else if (iter == ucounts)
 			ret = new;
+		max = READ_ONCE(iter->ns->ucount_max[type]);
 	}
 	return ret;
 }
@@ -306,15 +309,16 @@
 {
 	/* Caller must hold a reference to ucounts */
 	struct ucounts *iter;
+	long max = LONG_MAX;
 	long dec, ret = 0;
 
 	for (iter = ucounts; iter; iter = iter->ns->ucounts) {
-		long max = READ_ONCE(iter->ns->ucount_max[type]);
 		long new = atomic_long_add_return(1, &iter->ucount[type]);
 		if (new < 0 || new > max)
-			goto unwind;
+			goto dec_unwind;
 		if (iter == ucounts)
 			ret = new;
+		max = READ_ONCE(iter->ns->ucount_max[type]);
 		/*
 		 * Grab an extra ucount reference for the caller when
 		 * the rlimit count was previously 0.
@@ -328,20 +332,21 @@
 dec_unwind:
 	dec = atomic_long_add_return(-1, &iter->ucount[type]);
 	WARN_ON_ONCE(dec < 0);
-unwind:
 	do_dec_rlimit_put_ucounts(ucounts, iter, type);
 	return 0;
 }
 
-bool is_ucounts_overlimit(struct ucounts *ucounts, enum ucount_type type, unsigned long max)
+bool is_ucounts_overlimit(struct ucounts *ucounts, enum ucount_type type, unsigned long rlimit)
 {
 	struct ucounts *iter;
-	if (get_ucounts_value(ucounts, type) > max)
-		return true;
+	long max = rlimit;
+	if (rlimit > LONG_MAX)
+		max = LONG_MAX;
 	for (iter = ucounts; iter; iter = iter->ns->ucounts) {
-		max = READ_ONCE(iter->ns->ucount_max[type]);
-		if (get_ucounts_value(iter, type) > max)
+		long val = get_ucounts_value(iter, type);
+		if (val < 0 || val > max)
 			return true;
+		max = READ_ONCE(iter->ns->ucount_max[type]);
 	}
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/user_namespace.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/user_namespace.c
@@ -21,6 +21,12 @@
 #include <linux/bsearch.h>
 #include <linux/sort.h>
 
+/*
+ * sysctl determining whether unprivileged users may unshare a new
+ * userns.  Allowed by default
+ */
+int unprivileged_userns_clone = 1;
+
 static struct kmem_cache *user_ns_cachep __read_mostly;
 static DEFINE_MUTEX(userns_state_mutex);
 
@@ -58,6 +64,18 @@
 	cred->user_ns = user_ns;
 }
 
+static unsigned long enforced_nproc_rlimit(void)
+{
+	unsigned long limit = RLIM_INFINITY;
+
+	/* Is RLIMIT_NPROC currently enforced? */
+	if (!uid_eq(current_uid(), GLOBAL_ROOT_UID) ||
+	    (current_user_ns() != &init_user_ns))
+		limit = rlimit(RLIMIT_NPROC);
+
+	return limit;
+}
+
 /*
  * Create a new user namespace, deriving the creator from the user in the
  * passed credentials, and replacing that user with the new root user for the
@@ -122,7 +140,7 @@
 	for (i = 0; i < MAX_PER_NAMESPACE_UCOUNTS; i++) {
 		ns->ucount_max[i] = INT_MAX;
 	}
-	set_rlimit_ucount_max(ns, UCOUNT_RLIMIT_NPROC, rlimit(RLIMIT_NPROC));
+	set_rlimit_ucount_max(ns, UCOUNT_RLIMIT_NPROC, enforced_nproc_rlimit());
 	set_rlimit_ucount_max(ns, UCOUNT_RLIMIT_MSGQUEUE, rlimit(RLIMIT_MSGQUEUE));
 	set_rlimit_ucount_max(ns, UCOUNT_RLIMIT_SIGPENDING, rlimit(RLIMIT_SIGPENDING));
 	set_rlimit_ucount_max(ns, UCOUNT_RLIMIT_MEMLOCK, rlimit(RLIMIT_MEMLOCK));
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/watch_queue.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/watch_queue.c
@@ -34,6 +34,27 @@
 #define WATCH_QUEUE_NOTE_SIZE 128
 #define WATCH_QUEUE_NOTES_PER_PAGE (PAGE_SIZE / WATCH_QUEUE_NOTE_SIZE)
 
+/*
+ * This must be called under the RCU read-lock, which makes
+ * sure that the wqueue still exists. It can then take the lock,
+ * and check that the wqueue hasn't been destroyed, which in
+ * turn makes sure that the notification pipe still exists.
+ */
+static inline bool lock_wqueue(struct watch_queue *wqueue)
+{
+	spin_lock_bh(&wqueue->lock);
+	if (unlikely(wqueue->defunct)) {
+		spin_unlock_bh(&wqueue->lock);
+		return false;
+	}
+	return true;
+}
+
+static inline void unlock_wqueue(struct watch_queue *wqueue)
+{
+	spin_unlock_bh(&wqueue->lock);
+}
+
 static void watch_queue_pipe_buf_release(struct pipe_inode_info *pipe,
 					 struct pipe_buffer *buf)
 {
@@ -54,6 +75,7 @@
 	bit += page->index;
 
 	set_bit(bit, wqueue->notes_bitmap);
+	generic_pipe_buf_release(pipe, buf);
 }
 
 // No try_steal function => no stealing
@@ -68,6 +90,10 @@
 
 /*
  * Post a notification to a watch queue.
+ *
+ * Must be called with the RCU lock for reading, and the
+ * watch_queue lock held, which guarantees that the pipe
+ * hasn't been released.
  */
 static bool post_one_notification(struct watch_queue *wqueue,
 				  struct watch_notification *n)
@@ -84,9 +110,6 @@
 
 	spin_lock_irq(&pipe->rd_wait.lock);
 
-	if (wqueue->defunct)
-		goto out;
-
 	mask = pipe->ring_size - 1;
 	head = pipe->head;
 	tail = pipe->tail;
@@ -112,7 +135,7 @@
 	buf->offset = offset;
 	buf->len = len;
 	buf->flags = PIPE_BUF_FLAG_WHOLE;
-	pipe->head = head + 1;
+	smp_store_release(&pipe->head, head + 1); /* vs pipe_read() */
 
 	if (!test_and_clear_bit(note, wqueue->notes_bitmap)) {
 		spin_unlock_irq(&pipe->rd_wait.lock);
@@ -202,7 +225,10 @@
 		if (security_post_notification(watch->cred, cred, n) < 0)
 			continue;
 
-		post_one_notification(wqueue, n);
+		if (lock_wqueue(wqueue)) {
+			post_one_notification(wqueue, n);
+			unlock_wqueue(wqueue);
+		}
 	}
 
 	rcu_read_unlock();
@@ -219,7 +245,6 @@
 	struct page **pages;
 	unsigned long *bitmap;
 	unsigned long user_bufs;
-	unsigned int bmsize;
 	int ret, i, nr_pages;
 
 	if (!wqueue)
@@ -243,10 +268,21 @@
 		goto error;
 	}
 
-	ret = pipe_resize_ring(pipe, nr_notes);
+	nr_notes = nr_pages * WATCH_QUEUE_NOTES_PER_PAGE;
+	ret = pipe_resize_ring(pipe, roundup_pow_of_two(nr_notes));
 	if (ret < 0)
 		goto error;
 
+	/*
+	 * pipe_resize_ring() does not update nr_accounted for watch_queue
+	 * pipes, because the above vastly overprovisions. Set nr_accounted on
+	 * and max_usage this pipe to the number that was actually charged to
+	 * the user above via account_pipe_buffers.
+	 */
+	pipe->max_usage = nr_pages;
+	pipe->nr_accounted = nr_pages;
+
+	ret = -ENOMEM;
 	pages = kcalloc(sizeof(struct page *), nr_pages, GFP_KERNEL);
 	if (!pages)
 		goto error;
@@ -258,21 +294,19 @@
 		pages[i]->index = i * WATCH_QUEUE_NOTES_PER_PAGE;
 	}
 
-	bmsize = (nr_notes + BITS_PER_LONG - 1) / BITS_PER_LONG;
-	bmsize *= sizeof(unsigned long);
-	bitmap = kmalloc(bmsize, GFP_KERNEL);
+	bitmap = bitmap_alloc(nr_notes, GFP_KERNEL);
 	if (!bitmap)
 		goto error_p;
 
-	memset(bitmap, 0xff, bmsize);
+	bitmap_fill(bitmap, nr_notes);
 	wqueue->notes = pages;
 	wqueue->notes_bitmap = bitmap;
 	wqueue->nr_pages = nr_pages;
-	wqueue->nr_notes = nr_pages * WATCH_QUEUE_NOTES_PER_PAGE;
+	wqueue->nr_notes = nr_notes;
 	return 0;
 
 error_p:
-	for (i = 0; i < nr_pages; i++)
+	while (--i >= 0)
 		__free_page(pages[i]);
 	kfree(pages);
 error:
@@ -310,7 +344,7 @@
 	    filter.__reserved != 0)
 		return -EINVAL;
 
-	tf = memdup_user(_filter->filters, filter.nr_filters * sizeof(*tf));
+	tf = memdup_array_user(_filter->filters, filter.nr_filters, sizeof(*tf));
 	if (IS_ERR(tf))
 		return PTR_ERR(tf);
 
@@ -320,7 +354,7 @@
 		    tf[i].info_mask & WATCH_INFO_LENGTH)
 			goto err_filter;
 		/* Ignore any unknown types */
-		if (tf[i].type >= sizeof(wfilter->type_filter) * 8)
+		if (tf[i].type >= WATCH_TYPE__NR)
 			continue;
 		nr_filter++;
 	}
@@ -336,7 +370,7 @@
 
 	q = wfilter->filters;
 	for (i = 0; i < filter.nr_filters; i++) {
-		if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG)
+		if (tf[i].type >= WATCH_TYPE__NR)
 			continue;
 
 		q->type			= tf[i].type;
@@ -371,6 +405,8 @@
 
 	for (i = 0; i < wqueue->nr_pages; i++)
 		__free_page(wqueue->notes[i]);
+	kfree(wqueue->notes);
+	bitmap_free(wqueue->notes_bitmap);
 
 	wfilter = rcu_access_pointer(wqueue->filter);
 	if (wfilter)
@@ -395,6 +431,7 @@
 	put_watch_queue(rcu_access_pointer(watch->queue));
 	atomic_dec(&watch->cred->user->nr_watches);
 	put_cred(watch->cred);
+	kfree(watch);
 }
 
 static void __put_watch(struct kref *kref)
@@ -427,6 +464,33 @@
 	rcu_assign_pointer(watch->queue, wqueue);
 }
 
+static int add_one_watch(struct watch *watch, struct watch_list *wlist, struct watch_queue *wqueue)
+{
+	const struct cred *cred;
+	struct watch *w;
+
+	hlist_for_each_entry(w, &wlist->watchers, list_node) {
+		struct watch_queue *wq = rcu_access_pointer(w->queue);
+		if (wqueue == wq && watch->id == w->id)
+			return -EBUSY;
+	}
+
+	cred = current_cred();
+	if (atomic_inc_return(&cred->user->nr_watches) > task_rlimit(current, RLIMIT_NOFILE)) {
+		atomic_dec(&cred->user->nr_watches);
+		return -EAGAIN;
+	}
+
+	watch->cred = get_cred(cred);
+	rcu_assign_pointer(watch->watch_list, wlist);
+
+	kref_get(&wqueue->usage);
+	kref_get(&watch->usage);
+	hlist_add_head(&watch->queue_node, &wqueue->watches);
+	hlist_add_head_rcu(&watch->list_node, &wlist->watchers);
+	return 0;
+}
+
 /**
  * add_watch_to_object - Add a watch on an object to a watch list
  * @watch: The watch to add
@@ -441,33 +505,21 @@
  */
 int add_watch_to_object(struct watch *watch, struct watch_list *wlist)
 {
-	struct watch_queue *wqueue = rcu_access_pointer(watch->queue);
-	struct watch *w;
-
-	hlist_for_each_entry(w, &wlist->watchers, list_node) {
-		struct watch_queue *wq = rcu_access_pointer(w->queue);
-		if (wqueue == wq && watch->id == w->id)
-			return -EBUSY;
-	}
+	struct watch_queue *wqueue;
+	int ret = -ENOENT;
 
-	watch->cred = get_current_cred();
-	rcu_assign_pointer(watch->watch_list, wlist);
+	rcu_read_lock();
 
-	if (atomic_inc_return(&watch->cred->user->nr_watches) >
-	    task_rlimit(current, RLIMIT_NOFILE)) {
-		atomic_dec(&watch->cred->user->nr_watches);
-		put_cred(watch->cred);
-		return -EAGAIN;
+	wqueue = rcu_access_pointer(watch->queue);
+	if (lock_wqueue(wqueue)) {
+		spin_lock(&wlist->lock);
+		ret = add_one_watch(watch, wlist, wqueue);
+		spin_unlock(&wlist->lock);
+		unlock_wqueue(wqueue);
 	}
 
-	spin_lock_bh(&wqueue->lock);
-	kref_get(&wqueue->usage);
-	kref_get(&watch->usage);
-	hlist_add_head(&watch->queue_node, &wqueue->watches);
-	spin_unlock_bh(&wqueue->lock);
-
-	hlist_add_head(&watch->list_node, &wlist->watchers);
-	return 0;
+	rcu_read_unlock();
+	return ret;
 }
 EXPORT_SYMBOL(add_watch_to_object);
 
@@ -518,20 +570,15 @@
 
 	wqueue = rcu_dereference(watch->queue);
 
-	/* We don't need the watch list lock for the next bit as RCU is
-	 * protecting *wqueue from deallocation.
-	 */
-	if (wqueue) {
+	if (lock_wqueue(wqueue)) {
 		post_one_notification(wqueue, &n.watch);
 
-		spin_lock_bh(&wqueue->lock);
-
 		if (!hlist_unhashed(&watch->queue_node)) {
 			hlist_del_init_rcu(&watch->queue_node);
 			put_watch(watch);
 		}
 
-		spin_unlock_bh(&wqueue->lock);
+		unlock_wqueue(wqueue);
 	}
 
 	if (wlist->release_watch) {
@@ -566,7 +613,7 @@
 	rcu_read_lock();
 	spin_lock_bh(&wqueue->lock);
 
-	/* Prevent new additions and prevent notifications from happening */
+	/* Prevent new notifications from being stored. */
 	wqueue->defunct = true;
 
 	while (!hlist_empty(&wqueue->watches)) {
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/watchdog.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/watchdog.c
@@ -183,6 +183,13 @@
 static DEFINE_PER_CPU(unsigned long, hrtimer_interrupts_saved);
 static unsigned long soft_lockup_nmi_warn;
 
+static int __init softlockup_panic_setup(char *str)
+{
+	softlockup_panic = simple_strtoul(str, NULL, 0);
+	return 1;
+}
+__setup("softlockup_panic=", softlockup_panic_setup);
+
 static int __init nowatchdog_setup(char *str)
 {
 	watchdog_user_enabled = 0;
@@ -537,7 +544,7 @@
 	return 0;
 }
 
-static void lockup_detector_reconfigure(void)
+static void __lockup_detector_reconfigure(void)
 {
 	cpus_read_lock();
 	watchdog_nmi_stop();
@@ -557,6 +564,13 @@
 	__lockup_detector_cleanup();
 }
 
+void lockup_detector_reconfigure(void)
+{
+	mutex_lock(&watchdog_mutex);
+	__lockup_detector_reconfigure();
+	mutex_unlock(&watchdog_mutex);
+}
+
 /*
  * Create the watchdog infrastructure and configure the detector(s).
  */
@@ -573,13 +587,13 @@
 		return;
 
 	mutex_lock(&watchdog_mutex);
-	lockup_detector_reconfigure();
+	__lockup_detector_reconfigure();
 	softlockup_initialized = true;
 	mutex_unlock(&watchdog_mutex);
 }
 
 #else /* CONFIG_SOFTLOCKUP_DETECTOR */
-static void lockup_detector_reconfigure(void)
+static void __lockup_detector_reconfigure(void)
 {
 	cpus_read_lock();
 	watchdog_nmi_stop();
@@ -587,9 +601,13 @@
 	watchdog_nmi_start();
 	cpus_read_unlock();
 }
+void lockup_detector_reconfigure(void)
+{
+	__lockup_detector_reconfigure();
+}
 static inline void lockup_detector_setup(void)
 {
-	lockup_detector_reconfigure();
+	__lockup_detector_reconfigure();
 }
 #endif /* !CONFIG_SOFTLOCKUP_DETECTOR */
 
@@ -629,7 +647,7 @@
 {
 	/* Remove impossible cpus to keep sysctl output clean. */
 	cpumask_and(&watchdog_cpumask, &watchdog_cpumask, cpu_possible_mask);
-	lockup_detector_reconfigure();
+	__lockup_detector_reconfigure();
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/watchdog_hld.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/watchdog_hld.c
@@ -91,11 +91,15 @@
 	__this_cpu_write(last_timestamp, now);
 	return true;
 }
-#else
-static inline bool watchdog_check_timestamp(void)
+
+static void watchdog_init_timestamp(void)
 {
-	return true;
+	__this_cpu_write(nmi_rearmed, 0);
+	__this_cpu_write(last_timestamp, ktime_get_mono_fast_ns());
 }
+#else
+static inline bool watchdog_check_timestamp(void) { return true; }
+static inline void watchdog_init_timestamp(void) { }
 #endif
 
 static struct perf_event_attr wd_hw_attr = {
@@ -114,14 +118,14 @@
 	/* Ensure the watchdog never gets throttled */
 	event->hw.interrupts = 0;
 
+	if (!watchdog_check_timestamp())
+		return;
+
 	if (__this_cpu_read(watchdog_nmi_touch) == true) {
 		__this_cpu_write(watchdog_nmi_touch, false);
 		return;
 	}
 
-	if (!watchdog_check_timestamp())
-		return;
-
 	/* check for a hardlockup
 	 * This is done by making sure our timer interrupt
 	 * is incrementing.  The timer interrupt should have
@@ -196,6 +200,7 @@
 	if (!atomic_fetch_inc(&watchdog_cpus))
 		pr_info("Enabled. Permanently consumes one hw-PMU counter.\n");
 
+	watchdog_init_timestamp();
 	perf_event_enable(this_cpu_read(watchdog_ev));
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/kernel/workqueue.c
+++ linux-xilinx-zynqmp-5.15.0/kernel/workqueue.c
@@ -375,6 +375,7 @@
 static int worker_thread(void *__worker);
 static void workqueue_sysfs_unregister(struct workqueue_struct *wq);
 static void show_pwq(struct pool_workqueue *pwq);
+static void show_one_worker_pool(struct worker_pool *pool);
 
 #define CREATE_TRACE_POINTS
 #include <trace/events/workqueue.h>
@@ -696,12 +697,17 @@
 	set_work_data(work, WORK_STRUCT_NO_POOL, 0);
 }
 
+static inline struct pool_workqueue *work_struct_pwq(unsigned long data)
+{
+	return (struct pool_workqueue *)(data & WORK_STRUCT_WQ_DATA_MASK);
+}
+
 static struct pool_workqueue *get_work_pwq(struct work_struct *work)
 {
 	unsigned long data = atomic_long_read(&work->data);
 
 	if (data & WORK_STRUCT_PWQ)
-		return (void *)(data & WORK_STRUCT_WQ_DATA_MASK);
+		return work_struct_pwq(data);
 	else
 		return NULL;
 }
@@ -729,8 +735,7 @@
 	assert_rcu_or_pool_mutex();
 
 	if (data & WORK_STRUCT_PWQ)
-		return ((struct pool_workqueue *)
-			(data & WORK_STRUCT_WQ_DATA_MASK))->pool;
+		return work_struct_pwq(data)->pool;
 
 	pool_id = data >> WORK_OFFQ_POOL_SHIFT;
 	if (pool_id == WORK_OFFQ_POOL_NONE)
@@ -751,8 +756,7 @@
 	unsigned long data = atomic_long_read(&work->data);
 
 	if (data & WORK_STRUCT_PWQ)
-		return ((struct pool_workqueue *)
-			(data & WORK_STRUCT_WQ_DATA_MASK))->pool->id;
+		return work_struct_pwq(data)->pool->id;
 
 	return data >> WORK_OFFQ_POOL_SHIFT;
 }
@@ -867,8 +871,17 @@
 
 	if (!worker->sleeping)
 		return;
+
+	/*
+	 * If preempted by unbind_workers() between the WORKER_NOT_RUNNING check
+	 * and the nr_running increment below, we may ruin the nr_running reset
+	 * and leave with an unexpected pool->nr_running == 1 on the newly unbound
+	 * pool. Protect against such race.
+	 */
+	preempt_disable();
 	if (!(worker->flags & WORKER_NOT_RUNNING))
 		atomic_inc(&worker->pool->nr_running);
+	preempt_enable();
 	worker->sleeping = 0;
 }
 
@@ -3074,10 +3087,8 @@
 	if (WARN_ON(!work->func))
 		return false;
 
-	if (!from_cancel) {
-		lock_map_acquire(&work->lockdep_map);
-		lock_map_release(&work->lockdep_map);
-	}
+	lock_map_acquire(&work->lockdep_map);
+	lock_map_release(&work->lockdep_map);
 
 	if (start_flush_work(work, &barr, from_cancel)) {
 		wait_for_completion(&barr.done);
@@ -3266,6 +3277,15 @@
 	return ret;
 }
 
+/*
+ * See cancel_delayed_work()
+ */
+bool cancel_work(struct work_struct *work)
+{
+	return __cancel_work(work, false);
+}
+EXPORT_SYMBOL(cancel_work);
+
 /**
  * cancel_delayed_work - cancel a delayed work
  * @dwork: delayed_work to cancel
@@ -4447,7 +4467,7 @@
 			raw_spin_unlock_irq(&pwq->pool->lock);
 			mutex_unlock(&wq->mutex);
 			mutex_unlock(&wq_pool_mutex);
-			show_workqueue_state();
+			show_one_workqueue(wq);
 			return;
 		}
 		raw_spin_unlock_irq(&pwq->pool->lock);
@@ -4797,97 +4817,120 @@
 }
 
 /**
- * show_workqueue_state - dump workqueue state
- *
- * Called from a sysrq handler or try_to_freeze_tasks() and prints out
- * all busy workqueues and pools.
+ * show_one_workqueue - dump state of specified workqueue
+ * @wq: workqueue whose state will be printed
  */
-void show_workqueue_state(void)
+void show_one_workqueue(struct workqueue_struct *wq)
 {
-	struct workqueue_struct *wq;
-	struct worker_pool *pool;
+	struct pool_workqueue *pwq;
+	bool idle = true;
 	unsigned long flags;
-	int pi;
 
-	rcu_read_lock();
-
-	pr_info("Showing busy workqueues and worker pools:\n");
-
-	list_for_each_entry_rcu(wq, &workqueues, list) {
-		struct pool_workqueue *pwq;
-		bool idle = true;
-
-		for_each_pwq(pwq, wq) {
-			if (pwq->nr_active || !list_empty(&pwq->inactive_works)) {
-				idle = false;
-				break;
-			}
+	for_each_pwq(pwq, wq) {
+		if (pwq->nr_active || !list_empty(&pwq->inactive_works)) {
+			idle = false;
+			break;
 		}
-		if (idle)
-			continue;
+	}
+	if (idle) /* Nothing to print for idle workqueue */
+		return;
 
-		pr_info("workqueue %s: flags=0x%x\n", wq->name, wq->flags);
+	pr_info("workqueue %s: flags=0x%x\n", wq->name, wq->flags);
 
-		for_each_pwq(pwq, wq) {
-			raw_spin_lock_irqsave(&pwq->pool->lock, flags);
-			if (pwq->nr_active || !list_empty(&pwq->inactive_works)) {
-				/*
-				 * Defer printing to avoid deadlocks in console
-				 * drivers that queue work while holding locks
-				 * also taken in their write paths.
-				 */
-				printk_deferred_enter();
-				show_pwq(pwq);
-				printk_deferred_exit();
-			}
-			raw_spin_unlock_irqrestore(&pwq->pool->lock, flags);
+	for_each_pwq(pwq, wq) {
+		raw_spin_lock_irqsave(&pwq->pool->lock, flags);
+		if (pwq->nr_active || !list_empty(&pwq->inactive_works)) {
 			/*
-			 * We could be printing a lot from atomic context, e.g.
-			 * sysrq-t -> show_workqueue_state(). Avoid triggering
-			 * hard lockup.
+			 * Defer printing to avoid deadlocks in console
+			 * drivers that queue work while holding locks
+			 * also taken in their write paths.
 			 */
-			touch_nmi_watchdog();
-		}
-	}
-
-	for_each_pool(pool, pi) {
-		struct worker *worker;
-		bool first = true;
-
-		raw_spin_lock_irqsave(&pool->lock, flags);
-		if (pool->nr_workers == pool->nr_idle)
-			goto next_pool;
-		/*
-		 * Defer printing to avoid deadlocks in console drivers that
-		 * queue work while holding locks also taken in their write
-		 * paths.
-		 */
-		printk_deferred_enter();
-		pr_info("pool %d:", pool->id);
-		pr_cont_pool_info(pool);
-		pr_cont(" hung=%us workers=%d",
-			jiffies_to_msecs(jiffies - pool->watchdog_ts) / 1000,
-			pool->nr_workers);
-		if (pool->manager)
-			pr_cont(" manager: %d",
-				task_pid_nr(pool->manager->task));
-		list_for_each_entry(worker, &pool->idle_list, entry) {
-			pr_cont(" %s%d", first ? "idle: " : "",
-				task_pid_nr(worker->task));
-			first = false;
+			printk_deferred_enter();
+			show_pwq(pwq);
+			printk_deferred_exit();
 		}
-		pr_cont("\n");
-		printk_deferred_exit();
-	next_pool:
-		raw_spin_unlock_irqrestore(&pool->lock, flags);
+		raw_spin_unlock_irqrestore(&pwq->pool->lock, flags);
 		/*
 		 * We could be printing a lot from atomic context, e.g.
-		 * sysrq-t -> show_workqueue_state(). Avoid triggering
+		 * sysrq-t -> show_all_workqueues(). Avoid triggering
 		 * hard lockup.
 		 */
 		touch_nmi_watchdog();
 	}
 
+}
+
+/**
+ * show_one_worker_pool - dump state of specified worker pool
+ * @pool: worker pool whose state will be printed
+ */
+static void show_one_worker_pool(struct worker_pool *pool)
+{
+	struct worker *worker;
+	bool first = true;
+	unsigned long flags;
+	unsigned long hung = 0;
+
+	raw_spin_lock_irqsave(&pool->lock, flags);
+	if (pool->nr_workers == pool->nr_idle)
+		goto next_pool;
+
+	/* How long the first pending work is waiting for a worker. */
+	if (!list_empty(&pool->worklist))
+		hung = jiffies_to_msecs(jiffies - pool->watchdog_ts) / 1000;
+
+	/*
+	 * Defer printing to avoid deadlocks in console drivers that
+	 * queue work while holding locks also taken in their write
+	 * paths.
+	 */
+	printk_deferred_enter();
+	pr_info("pool %d:", pool->id);
+	pr_cont_pool_info(pool);
+	pr_cont(" hung=%lus workers=%d", hung, pool->nr_workers);
+	if (pool->manager)
+		pr_cont(" manager: %d",
+			task_pid_nr(pool->manager->task));
+	list_for_each_entry(worker, &pool->idle_list, entry) {
+		pr_cont(" %s%d", first ? "idle: " : "",
+			task_pid_nr(worker->task));
+		first = false;
+	}
+	pr_cont("\n");
+	printk_deferred_exit();
+next_pool:
+	raw_spin_unlock_irqrestore(&pool->lock, flags);
+	/*
+	 * We could be printing a lot from atomic context, e.g.
+	 * sysrq-t -> show_all_workqueues(). Avoid triggering
+	 * hard lockup.
+	 */
+	touch_nmi_watchdog();
+
+}
+
+/**
+ * show_all_workqueues - dump workqueue state
+ *
+ * Called from a sysrq handler or try_to_freeze_tasks() and prints out
+ * all busy workqueues and pools.
+ */
+void show_all_workqueues(void)
+{
+	struct workqueue_struct *wq;
+	struct worker_pool *pool;
+	int pi;
+
+	rcu_read_lock();
+
+	pr_info("Showing busy workqueues and worker pools:\n");
+
+	list_for_each_entry_rcu(wq, &workqueues, list)
+		show_one_workqueue(wq);
+
+	for_each_pool(pool, pi)
+		show_one_worker_pool(pool);
+
 	rcu_read_unlock();
 }
 
@@ -5175,50 +5218,54 @@
 }
 
 /**
- * work_on_cpu - run a function in thread context on a particular cpu
+ * work_on_cpu_key - run a function in thread context on a particular cpu
  * @cpu: the cpu to run on
  * @fn: the function to run
  * @arg: the function arg
+ * @key: The lock class key for lock debugging purposes
  *
  * It is up to the caller to ensure that the cpu doesn't go offline.
  * The caller must not hold any locks which would prevent @fn from completing.
  *
  * Return: The value @fn returns.
  */
-long work_on_cpu(int cpu, long (*fn)(void *), void *arg)
+long work_on_cpu_key(int cpu, long (*fn)(void *),
+		     void *arg, struct lock_class_key *key)
 {
 	struct work_for_cpu wfc = { .fn = fn, .arg = arg };
 
-	INIT_WORK_ONSTACK(&wfc.work, work_for_cpu_fn);
+	INIT_WORK_ONSTACK_KEY(&wfc.work, work_for_cpu_fn, key);
 	schedule_work_on(cpu, &wfc.work);
 	flush_work(&wfc.work);
 	destroy_work_on_stack(&wfc.work);
 	return wfc.ret;
 }
-EXPORT_SYMBOL_GPL(work_on_cpu);
+EXPORT_SYMBOL_GPL(work_on_cpu_key);
 
 /**
- * work_on_cpu_safe - run a function in thread context on a particular cpu
+ * work_on_cpu_safe_key - run a function in thread context on a particular cpu
  * @cpu: the cpu to run on
  * @fn:  the function to run
  * @arg: the function argument
+ * @key: The lock class key for lock debugging purposes
  *
  * Disables CPU hotplug and calls work_on_cpu(). The caller must not hold
  * any locks which would prevent @fn from completing.
  *
  * Return: The value @fn returns.
  */
-long work_on_cpu_safe(int cpu, long (*fn)(void *), void *arg)
+long work_on_cpu_safe_key(int cpu, long (*fn)(void *),
+			  void *arg, struct lock_class_key *key)
 {
 	long ret = -ENODEV;
 
 	cpus_read_lock();
 	if (cpu_online(cpu))
-		ret = work_on_cpu(cpu, fn, arg);
+		ret = work_on_cpu_key(cpu, fn, arg, key);
 	cpus_read_unlock();
 	return ret;
 }
-EXPORT_SYMBOL_GPL(work_on_cpu_safe);
+EXPORT_SYMBOL_GPL(work_on_cpu_safe_key);
 #endif /* CONFIG_SMP */
 
 #ifdef CONFIG_FREEZER
@@ -5345,9 +5392,13 @@
 	list_for_each_entry(wq, &workqueues, list) {
 		if (!(wq->flags & WQ_UNBOUND))
 			continue;
+
 		/* creating multiple pwqs breaks ordering guarantee */
-		if (wq->flags & __WQ_ORDERED)
-			continue;
+		if (!list_empty(&wq->pwqs)) {
+			if (wq->flags & __WQ_ORDERED_EXPLICIT)
+				continue;
+			wq->flags &= ~__WQ_ORDERED;
+		}
 
 		ctx = apply_wqattrs_prepare(wq, wq->unbound_attrs);
 		if (!ctx) {
@@ -5384,9 +5435,6 @@
 	int ret = -EINVAL;
 	cpumask_var_t saved_cpumask;
 
-	if (!zalloc_cpumask_var(&saved_cpumask, GFP_KERNEL))
-		return -ENOMEM;
-
 	/*
 	 * Not excluding isolated cpus on purpose.
 	 * If the user wishes to include them, we allow that.
@@ -5394,6 +5442,15 @@
 	cpumask_and(cpumask, cpumask, cpu_possible_mask);
 	if (!cpumask_empty(cpumask)) {
 		apply_wqattrs_lock();
+		if (cpumask_equal(cpumask, wq_unbound_cpumask)) {
+			ret = 0;
+			goto out_unlock;
+		}
+
+		if (!zalloc_cpumask_var(&saved_cpumask, GFP_KERNEL)) {
+			ret = -ENOMEM;
+			goto out_unlock;
+		}
 
 		/* save the old wq_unbound_cpumask. */
 		cpumask_copy(saved_cpumask, wq_unbound_cpumask);
@@ -5406,10 +5463,11 @@
 		if (ret < 0)
 			cpumask_copy(wq_unbound_cpumask, saved_cpumask);
 
+		free_cpumask_var(saved_cpumask);
+out_unlock:
 		apply_wqattrs_unlock();
 	}
 
-	free_cpumask_var(saved_cpumask);
 	return ret;
 }
 
@@ -5869,7 +5927,7 @@
 	rcu_read_unlock();
 
 	if (lockup_detected)
-		show_workqueue_state();
+		show_all_workqueues();
 
 	wq_watchdog_reset_touched();
 	mod_timer(&wq_watchdog_timer, jiffies + thresh);
@@ -5877,10 +5935,18 @@
 
 notrace void wq_watchdog_touch(int cpu)
 {
+	unsigned long thresh = READ_ONCE(wq_watchdog_thresh) * HZ;
+	unsigned long touch_ts = READ_ONCE(wq_watchdog_touched);
+	unsigned long now = jiffies;
+
 	if (cpu >= 0)
-		per_cpu(wq_watchdog_touched_cpu, cpu) = jiffies;
+		per_cpu(wq_watchdog_touched_cpu, cpu) = now;
+	else
+		WARN_ONCE(1, "%s should be called with valid CPU", __func__);
 
-	wq_watchdog_touched = jiffies;
+	/* Don't unnecessarily store to global cacheline */
+	if (time_after(now, touch_ts + thresh / 4))
+		WRITE_ONCE(wq_watchdog_touched, jiffies);
 }
 
 static void wq_watchdog_set_thresh(unsigned long thresh)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/842/842_compress.c
+++ linux-xilinx-zynqmp-5.15.0/lib/842/842_compress.c
@@ -532,6 +532,8 @@
 		}
 		if (repeat_count) {
 			ret = add_repeat_template(p, repeat_count);
+			if (ret)
+				return ret;
 			repeat_count = 0;
 			if (next == last) /* reached max repeat bits */
 				goto repeat;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/lib/Kconfig
@@ -45,7 +45,6 @@
 config HAVE_ARCH_BITREVERSE
 	bool
 	default n
-	depends on BITREVERSE
 	help
 	  This option enables the use of hardware bit-reversal instructions on
 	  architectures which support such operations.
@@ -122,6 +121,11 @@
 	  mmio accesses when the IO memory address is not a registered
 	  emulated region.
 
+source "lib/crypto/Kconfig"
+
+config LIB_MEMNEQ
+	bool
+
 config CRC_CCITT
 	tristate "CRC-CCITT functions"
 	help
@@ -680,6 +684,11 @@
 	 Select the hash size as a power of 2 for the stackdepot hash table.
 	 Choose a lower value to reduce the memory impact.
 
+config REF_TRACKER
+	bool
+	depends on STACKTRACE_SUPPORT
+	select STACKDEPOT
+
 config SBITMAP
 	bool
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/lib/Kconfig.debug
@@ -208,6 +208,11 @@
 
 endmenu # "printk and dmesg options"
 
+# Clang is known to generate .{s,u}leb128 with symbol deltas with DWARF5, which
+# some targets may not support: https://sourceware.org/bugzilla/show_bug.cgi?id=27215
+config AS_HAS_NON_CONST_LEB128
+	def_bool $(as-instr,.uleb128 .Lexpr_end4 - .Lexpr_start3\n.Lexpr_start3:\n.Lexpr_end4:)
+
 menu "Compile-time checks and compiler options"
 
 config DEBUG_INFO
@@ -274,6 +279,7 @@
 
 config DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
 	bool "Rely on the toolchain's implicit default DWARF version"
+	depends on !CC_IS_CLANG || AS_IS_LLVM || CLANG_VERSION < 140000 || (AS_IS_GNU && AS_VERSION >= 23502 && AS_HAS_NON_CONST_LEB128)
 	help
 	  The implicit default version of DWARF debug info produced by a
 	  toolchain changes over time.
@@ -295,8 +301,8 @@
 
 config DEBUG_INFO_DWARF5
 	bool "Generate DWARF Version 5 debuginfo"
-	depends on !CC_IS_CLANG || (CC_IS_CLANG && (AS_IS_LLVM || (AS_IS_GNU && AS_VERSION >= 23502)))
-	depends on !DEBUG_INFO_BTF
+	depends on !CC_IS_CLANG || AS_IS_LLVM || (AS_IS_GNU && AS_VERSION >= 23502 && AS_HAS_NON_CONST_LEB128)
+	depends on !DEBUG_INFO_BTF || PAHOLE_VERSION >= 121
 	help
 	  Generate DWARF v5 debug info. Requires binutils 2.35.2, gcc 5.0+ (gcc
 	  5.0+ accepts the -gdwarf-5 flag but only had partial support for some
@@ -313,7 +319,7 @@
 endchoice # "DWARF version"
 
 config DEBUG_INFO_BTF
-	bool "Generate BTF typeinfo"
+	bool "Generate BTF type information"
 	depends on !DEBUG_INFO_SPLIT && !DEBUG_INFO_REDUCED
 	depends on !GCC_PLUGIN_RANDSTRUCT || COMPILE_TEST
 	help
@@ -322,10 +328,11 @@
 	  DWARF type info into equivalent deduplicated BTF type info.
 
 config PAHOLE_HAS_SPLIT_BTF
-	def_bool $(success, test `$(PAHOLE) --version | sed -E 's/v([0-9]+)\.([0-9]+)/\1\2/'` -ge "119")
+	def_bool PAHOLE_VERSION >= 119
 
 config DEBUG_INFO_BTF_MODULES
-	def_bool y
+	bool "Generate BTF type information for kernel modules"
+	default y
 	depends on DEBUG_INFO_BTF && MODULES && PAHOLE_HAS_SPLIT_BTF
 	help
 	  Generate compact split BTF type information for kernel modules.
@@ -346,8 +353,10 @@
 	int "Warn for stack frames larger than"
 	range 0 8192
 	default 2048 if GCC_PLUGIN_LATENT_ENTROPY
-	default 1536 if (!64BIT && (PARISC || XTENSA))
-	default 1024 if (!64BIT && !PARISC)
+	default 2048 if PARISC
+	default 1536 if (!64BIT && XTENSA)
+	default 1280 if KASAN && !64BIT
+	default 1024 if !64BIT
 	default 2048 if 64BIT
 	help
 	  Tell gcc to warn at build time for stack frames larger than this.
@@ -414,7 +423,9 @@
 	  If unsure, say Y.
 
 config DEBUG_FORCE_FUNCTION_ALIGN_64B
-	bool "Force all function address 64B aligned" if EXPERT
+	bool "Force all function address 64B aligned"
+	depends on EXPERT && (X86_64 || ARM64 || PPC32 || PPC64 || ARC)
+	select FUNCTION_ALIGNMENT_64B
 	help
 	  There are cases that a commit from one domain changes the function
 	  address alignment of other domains, and cause magic performance
@@ -597,6 +608,11 @@
 	  Say Y here if you need to enable miscellaneous debug code that should
 	  be under a more specific debug option but isn't.
 
+menu "Networking Debugging"
+
+source "net/Kconfig.debug"
+
+endmenu # "Networking Debugging"
 
 menu "Memory Debugging"
 
@@ -1217,13 +1233,16 @@
 config DEBUG_PREEMPT
 	bool "Debug preemptible kernel"
 	depends on DEBUG_KERNEL && PREEMPTION && TRACE_IRQFLAGS_SUPPORT
-	default y
 	help
 	  If you say Y here then the kernel will use a debug variant of the
 	  commonly used smp_processor_id() function and will print warnings
 	  if kernel code uses it in a preemption-unsafe way. Also, the kernel
 	  will detect preemption count underflows.
 
+	  This option has potential to introduce high runtime overhead,
+	  depending on workload as it triggers debugging routines for each
+	  this_cpu operation. It should only be used for debugging purposes.
+
 menu "Lock Debugging (spinlocks, mutexes, etc...)"
 
 config LOCK_DEBUGGING_SUPPORT
@@ -1394,7 +1413,7 @@
 config LOCKDEP_BITS
 	int "Bitsize for MAX_LOCKDEP_ENTRIES"
 	depends on LOCKDEP && !LOCKDEP_SMALL
-	range 10 30
+	range 10 24
 	default 15
 	help
 	  Try increasing this value if you hit "BUG: MAX_LOCKDEP_ENTRIES too low!" message.
@@ -1410,7 +1429,7 @@
 config LOCKDEP_STACK_TRACE_BITS
 	int "Bitsize for MAX_STACK_TRACE_ENTRIES"
 	depends on LOCKDEP && !LOCKDEP_SMALL
-	range 10 30
+	range 10 26
 	default 19
 	help
 	  Try increasing this value if you hit "BUG: MAX_STACK_TRACE_ENTRIES too low!" message.
@@ -1418,7 +1437,7 @@
 config LOCKDEP_STACK_TRACE_HASH_BITS
 	int "Bitsize for STACK_TRACE_HASH_SIZE"
 	depends on LOCKDEP && !LOCKDEP_SMALL
-	range 10 30
+	range 10 26
 	default 14
 	help
 	  Try increasing this value if you need large MAX_STACK_TRACE_ENTRIES.
@@ -1426,7 +1445,7 @@
 config LOCKDEP_CIRCULAR_QUEUE_BITS
 	int "Bitsize for elements in circular_queue struct"
 	depends on LOCKDEP
-	range 10 30
+	range 10 26
 	default 12
 	help
 	  Try increasing this value if you hit "lockdep bfs error:-1" warning due to __cq_enqueue() failure.
@@ -1558,8 +1577,7 @@
 	  so architecture maintainers really need to do what they can
 	  to get the CRNG seeded sooner after the system is booted.
 	  However, since users cannot do anything actionable to
-	  address this, by default the kernel will issue only a single
-	  warning for the first use of unseeded randomness.
+	  address this, by default this option is disabled.
 
 	  Say Y here if you want to receive warnings for all uses of
 	  unseeded randomness.  This will be of use primarily for
@@ -1866,8 +1884,14 @@
 	  If unsure, say N.
 
 config FUNCTION_ERROR_INJECTION
-	def_bool y
+	bool "Fault-injections of functions"
 	depends on HAVE_FUNCTION_ERROR_INJECTION && KPROBES
+	help
+	  Add fault injections into various functions that are annotated with
+	  ALLOW_ERROR_INJECTION() in the kernel. BPF may also modify the return
+	  value of theses functions. This is useful to test error paths of code.
+
+	  If unsure, say N
 
 config FAULT_INJECTION
 	bool "Fault-injection framework"
--- linux-xilinx-zynqmp-5.15.0.orig/lib/Kconfig.kfence
+++ linux-xilinx-zynqmp-5.15.0/lib/Kconfig.kfence
@@ -25,17 +25,6 @@
 
 if KFENCE
 
-config KFENCE_STATIC_KEYS
-	bool "Use static keys to set up allocations"
-	default y
-	depends on JUMP_LABEL # To ensure performance, require jump labels
-	help
-	  Use static keys (static branches) to set up KFENCE allocations. Using
-	  static keys is normally recommended, because it avoids a dynamic
-	  branch in the allocator's fast path. However, with very low sample
-	  intervals, or on systems that do not support jump labels, a dynamic
-	  branch may still be an acceptable performance trade-off.
-
 config KFENCE_SAMPLE_INTERVAL
 	int "Default sample interval in milliseconds"
 	default 100
@@ -56,6 +45,33 @@
 	  pages are required; with one containing the object and two adjacent
 	  ones used as guard pages.
 
+config KFENCE_DEFERRABLE
+	bool "Use a deferrable timer to trigger allocations"
+	help
+	  Use a deferrable timer to trigger allocations. This avoids forcing
+	  CPU wake-ups if the system is idle, at the risk of a less predictable
+	  sample interval.
+
+	  Warning: The KUnit test suite fails with this option enabled - due to
+	  the unpredictability of the sample interval!
+
+	  Say N if you are unsure.
+
+config KFENCE_STATIC_KEYS
+	bool "Use static keys to set up allocations" if EXPERT
+	depends on JUMP_LABEL
+	help
+	  Use static keys (static branches) to set up KFENCE allocations. This
+	  option is only recommended when using very large sample intervals, or
+	  performance has carefully been evaluated with this option.
+
+	  Using static keys comes with trade-offs that need to be carefully
+	  evaluated given target workloads and system architectures. Notably,
+	  enabling and disabling static keys invoke IPI broadcasts, the latency
+	  and impact of which is much harder to predict than a dynamic branch.
+
+	  Say N if you are unsure.
+
 config KFENCE_STRESS_TEST_FAULTS
 	int "Stress testing of fault handling and error reporting" if EXPERT
 	default 0
--- linux-xilinx-zynqmp-5.15.0.orig/lib/Kconfig.ubsan
+++ linux-xilinx-zynqmp-5.15.0/lib/Kconfig.ubsan
@@ -112,19 +112,6 @@
 	  This option enables -fsanitize=unreachable which checks for control
 	  flow reaching an expected-to-be-unreachable position.
 
-config UBSAN_OBJECT_SIZE
-	bool "Perform checking for accesses beyond the end of objects"
-	default UBSAN
-	# gcc hugely expands stack usage with -fsanitize=object-size
-	# https://lore.kernel.org/lkml/CAHk-=wjPasyJrDuwDnpHJS2TuQfExwe=px-SzLeN8GFMAQJPmQ@mail.gmail.com/
-	depends on !CC_IS_GCC
-	depends on $(cc-option,-fsanitize=object-size)
-	help
-	  This option enables -fsanitize=object-size which checks for accesses
-	  beyond the end of objects where the optimizer can determine both the
-	  object being operated on and its size, usually seen with bad downcasts,
-	  or access to struct members from NULL pointers.
-
 config UBSAN_BOOL
 	bool "Perform checking for non-boolean values used as boolean"
 	default UBSAN
--- linux-xilinx-zynqmp-5.15.0.orig/lib/Makefile
+++ linux-xilinx-zynqmp-5.15.0/lib/Makefile
@@ -249,6 +249,7 @@
 obj-$(CONFIG_SIGNATURE) += digsig.o
 
 lib-$(CONFIG_CLZ_TAB) += clz_tab.o
+lib-$(CONFIG_LIB_MEMNEQ) += memneq.o
 
 obj-$(CONFIG_GENERIC_STRNCPY_FROM_USER) += strncpy_from_user.o
 obj-$(CONFIG_GENERIC_STRNLEN_USER) += strnlen_user.o
@@ -269,13 +270,15 @@
 KASAN_SANITIZE_stackdepot.o := n
 KCOV_INSTRUMENT_stackdepot.o := n
 
+obj-$(CONFIG_REF_TRACKER) += ref_tracker.o
+
 libfdt_files = fdt.o fdt_ro.o fdt_wip.o fdt_rw.o fdt_sw.o fdt_strerror.o \
 	       fdt_empty_tree.o fdt_addresses.o
 $(foreach file, $(libfdt_files), \
 	$(eval CFLAGS_$(file) = -I $(srctree)/scripts/dtc/libfdt))
 lib-$(CONFIG_LIBFDT) += $(libfdt_files)
 
-lib-$(CONFIG_BOOT_CONFIG) += bootconfig.o
+obj-$(CONFIG_BOOT_CONFIG) += bootconfig.o
 
 obj-$(CONFIG_RBTREE_TEST) += rbtree_test.o
 obj-$(CONFIG_INTERVAL_TREE_TEST) += interval_tree_test.o
--- linux-xilinx-zynqmp-5.15.0.orig/lib/assoc_array.c
+++ linux-xilinx-zynqmp-5.15.0/lib/assoc_array.c
@@ -1462,6 +1462,7 @@
 	struct assoc_array_ptr *cursor, *ptr;
 	struct assoc_array_ptr *new_root, *new_parent, **new_ptr_pp;
 	unsigned long nr_leaves_on_tree;
+	bool retained;
 	int keylen, slot, nr_free, next_slot, i;
 
 	pr_devel("-->%s()\n", __func__);
@@ -1538,6 +1539,7 @@
 		goto descend;
 	}
 
+retry_compress:
 	pr_devel("-- compress node %p --\n", new_n);
 
 	/* Count up the number of empty slots in this node and work out the
@@ -1555,6 +1557,7 @@
 	pr_devel("free=%d, leaves=%lu\n", nr_free, new_n->nr_leaves_on_branch);
 
 	/* See what we can fold in */
+	retained = false;
 	next_slot = 0;
 	for (slot = 0; slot < ASSOC_ARRAY_FAN_OUT; slot++) {
 		struct assoc_array_shortcut *s;
@@ -1604,9 +1607,14 @@
 			pr_devel("[%d] retain node %lu/%d [nx %d]\n",
 				 slot, child->nr_leaves_on_branch, nr_free + 1,
 				 next_slot);
+			retained = true;
 		}
 	}
 
+	if (retained && new_n->nr_leaves_on_branch <= ASSOC_ARRAY_FAN_OUT) {
+		pr_devel("internal nodes remain despite enough space, retrying\n");
+		goto retry_compress;
+	}
 	pr_devel("after: %lu\n", new_n->nr_leaves_on_branch);
 
 	nr_leaves_on_tree = new_n->nr_leaves_on_branch;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/bug.c
+++ linux-xilinx-zynqmp-5.15.0/lib/bug.c
@@ -6,8 +6,7 @@
 
   CONFIG_BUG - emit BUG traps.  Nothing happens without this.
   CONFIG_GENERIC_BUG - enable this code.
-  CONFIG_GENERIC_BUG_RELATIVE_POINTERS - use 32-bit pointers relative to
-	the containing struct bug_entry for bug_addr and file.
+  CONFIG_GENERIC_BUG_RELATIVE_POINTERS - use 32-bit relative pointers for bug_addr and file
   CONFIG_DEBUG_BUGVERBOSE - emit full file+line information for each BUG
 
   CONFIG_BUG and CONFIG_DEBUG_BUGVERBOSE are potentially user-settable
@@ -53,10 +52,10 @@
 
 static inline unsigned long bug_addr(const struct bug_entry *bug)
 {
-#ifndef CONFIG_GENERIC_BUG_RELATIVE_POINTERS
-	return bug->bug_addr;
+#ifdef CONFIG_GENERIC_BUG_RELATIVE_POINTERS
+	return (unsigned long)&bug->bug_addr_disp + bug->bug_addr_disp;
 #else
-	return (unsigned long)bug + bug->bug_addr_disp;
+	return bug->bug_addr;
 #endif
 }
 
@@ -131,10 +130,10 @@
 		       unsigned int *line)
 {
 #ifdef CONFIG_DEBUG_BUGVERBOSE
-#ifndef CONFIG_GENERIC_BUG_RELATIVE_POINTERS
-	*file = bug->file;
+#ifdef CONFIG_GENERIC_BUG_RELATIVE_POINTERS
+	*file = (const char *)&bug->file_disp + bug->file_disp;
 #else
-	*file = (const char *)bug + bug->file_disp;
+	*file = bug->file;
 #endif
 	*line = bug->line;
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/lib/buildid.c
+++ linux-xilinx-zynqmp-5.15.0/lib/buildid.c
@@ -5,6 +5,7 @@
 #include <linux/elf.h>
 #include <linux/kernel.h>
 #include <linux/pagemap.h>
+#include <linux/secretmem.h>
 
 #define BUILD_ID 3
 
@@ -18,31 +19,37 @@
 			      const void *note_start,
 			      Elf32_Word note_size)
 {
-	Elf32_Word note_offs = 0, new_offs;
-
-	while (note_offs + sizeof(Elf32_Nhdr) < note_size) {
-		Elf32_Nhdr *nhdr = (Elf32_Nhdr *)(note_start + note_offs);
+	const char note_name[] = "GNU";
+	const size_t note_name_sz = sizeof(note_name);
+	u64 note_off = 0, new_off, name_sz, desc_sz;
+	const char *data;
+
+	while (note_off + sizeof(Elf32_Nhdr) < note_size &&
+	       note_off + sizeof(Elf32_Nhdr) > note_off /* overflow */) {
+		Elf32_Nhdr *nhdr = (Elf32_Nhdr *)(note_start + note_off);
+
+		name_sz = READ_ONCE(nhdr->n_namesz);
+		desc_sz = READ_ONCE(nhdr->n_descsz);
+
+		new_off = note_off + sizeof(Elf32_Nhdr);
+		if (check_add_overflow(new_off, ALIGN(name_sz, 4), &new_off) ||
+		    check_add_overflow(new_off, ALIGN(desc_sz, 4), &new_off) ||
+		    new_off > note_size)
+			break;
 
 		if (nhdr->n_type == BUILD_ID &&
-		    nhdr->n_namesz == sizeof("GNU") &&
-		    !strcmp((char *)(nhdr + 1), "GNU") &&
-		    nhdr->n_descsz > 0 &&
-		    nhdr->n_descsz <= BUILD_ID_SIZE_MAX) {
-			memcpy(build_id,
-			       note_start + note_offs +
-			       ALIGN(sizeof("GNU"), 4) + sizeof(Elf32_Nhdr),
-			       nhdr->n_descsz);
-			memset(build_id + nhdr->n_descsz, 0,
-			       BUILD_ID_SIZE_MAX - nhdr->n_descsz);
+		    name_sz == note_name_sz &&
+		    memcmp(nhdr + 1, note_name, note_name_sz) == 0 &&
+		    desc_sz > 0 && desc_sz <= BUILD_ID_SIZE_MAX) {
+			data = note_start + note_off + sizeof(Elf32_Nhdr) + ALIGN(note_name_sz, 4);
+			memcpy(build_id, data, desc_sz);
+			memset(build_id + desc_sz, 0, BUILD_ID_SIZE_MAX - desc_sz);
 			if (size)
-				*size = nhdr->n_descsz;
+				*size = desc_sz;
 			return 0;
 		}
-		new_offs = note_offs + sizeof(Elf32_Nhdr) +
-			ALIGN(nhdr->n_namesz, 4) + ALIGN(nhdr->n_descsz, 4);
-		if (new_offs <= note_offs)  /* overflow */
-			break;
-		note_offs = new_offs;
+
+		note_off = new_off;
 	}
 
 	return -EINVAL;
@@ -71,20 +78,28 @@
 {
 	Elf32_Ehdr *ehdr = (Elf32_Ehdr *)page_addr;
 	Elf32_Phdr *phdr;
-	int i;
+	__u32 i, phnum;
+
+	/*
+	 * FIXME
+	 * Neither ELF spec nor ELF loader require that program headers
+	 * start immediately after ELF header.
+	 */
+	if (ehdr->e_phoff != sizeof(Elf32_Ehdr))
+		return -EINVAL;
 
+	phnum = READ_ONCE(ehdr->e_phnum);
 	/* only supports phdr that fits in one page */
-	if (ehdr->e_phnum >
-	    (PAGE_SIZE - sizeof(Elf32_Ehdr)) / sizeof(Elf32_Phdr))
+	if (phnum > (PAGE_SIZE - sizeof(Elf32_Ehdr)) / sizeof(Elf32_Phdr))
 		return -EINVAL;
 
 	phdr = (Elf32_Phdr *)(page_addr + sizeof(Elf32_Ehdr));
 
-	for (i = 0; i < ehdr->e_phnum; ++i) {
+	for (i = 0; i < phnum; ++i) {
 		if (phdr[i].p_type == PT_NOTE &&
 		    !parse_build_id(page_addr, build_id, size,
-				    page_addr + phdr[i].p_offset,
-				    phdr[i].p_filesz))
+				    page_addr + READ_ONCE(phdr[i].p_offset),
+				    READ_ONCE(phdr[i].p_filesz)))
 			return 0;
 	}
 	return -EINVAL;
@@ -96,20 +111,28 @@
 {
 	Elf64_Ehdr *ehdr = (Elf64_Ehdr *)page_addr;
 	Elf64_Phdr *phdr;
-	int i;
+	__u32 i, phnum;
+
+	/*
+	 * FIXME
+	 * Neither ELF spec nor ELF loader require that program headers
+	 * start immediately after ELF header.
+	 */
+	if (ehdr->e_phoff != sizeof(Elf64_Ehdr))
+		return -EINVAL;
 
+	phnum = READ_ONCE(ehdr->e_phnum);
 	/* only supports phdr that fits in one page */
-	if (ehdr->e_phnum >
-	    (PAGE_SIZE - sizeof(Elf64_Ehdr)) / sizeof(Elf64_Phdr))
+	if (phnum > (PAGE_SIZE - sizeof(Elf64_Ehdr)) / sizeof(Elf64_Phdr))
 		return -EINVAL;
 
 	phdr = (Elf64_Phdr *)(page_addr + sizeof(Elf64_Ehdr));
 
-	for (i = 0; i < ehdr->e_phnum; ++i) {
+	for (i = 0; i < phnum; ++i) {
 		if (phdr[i].p_type == PT_NOTE &&
 		    !parse_build_id(page_addr, build_id, size,
-				    page_addr + phdr[i].p_offset,
-				    phdr[i].p_filesz))
+				    page_addr + READ_ONCE(phdr[i].p_offset),
+				    READ_ONCE(phdr[i].p_filesz)))
 			return 0;
 	}
 	return -EINVAL;
@@ -135,9 +158,17 @@
 	if (!vma->vm_file)
 		return -EINVAL;
 
+	/* reject secretmem folios created with memfd_secret() */
+	if (vma_is_secretmem(vma))
+		return -EFAULT;
+
 	page = find_get_page(vma->vm_file->f_mapping, 0);
 	if (!page)
 		return -EFAULT;	/* page not mapped */
+	if (!PageUptodate(page)) {
+		put_page(page);
+		return -EFAULT;
+	}
 
 	ret = -EINVAL;
 	page_addr = kmap_atomic(page);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/clz_ctz.c
+++ linux-xilinx-zynqmp-5.15.0/lib/clz_ctz.c
@@ -28,36 +28,16 @@
 }
 EXPORT_SYMBOL(__clzsi2);
 
-int __weak __clzdi2(long val);
-int __weak __ctzdi2(long val);
-#if BITS_PER_LONG == 32
-
-int __weak __clzdi2(long val)
+int __weak __clzdi2(u64 val);
+int __weak __clzdi2(u64 val)
 {
-	return 32 - fls((int)val);
+	return 64 - fls64(val);
 }
 EXPORT_SYMBOL(__clzdi2);
 
-int __weak __ctzdi2(long val)
+int __weak __ctzdi2(u64 val);
+int __weak __ctzdi2(u64 val)
 {
-	return __ffs((u32)val);
+	return __ffs64(val);
 }
 EXPORT_SYMBOL(__ctzdi2);
-
-#elif BITS_PER_LONG == 64
-
-int __weak __clzdi2(long val)
-{
-	return 64 - fls64((u64)val);
-}
-EXPORT_SYMBOL(__clzdi2);
-
-int __weak __ctzdi2(long val)
-{
-	return __ffs64((u64)val);
-}
-EXPORT_SYMBOL(__ctzdi2);
-
-#else
-#error BITS_PER_LONG not 32 or 64
-#endif
--- linux-xilinx-zynqmp-5.15.0.orig/lib/cmdline_kunit.c
+++ linux-xilinx-zynqmp-5.15.0/lib/cmdline_kunit.c
@@ -124,7 +124,7 @@
 			    n, e[0], r[0]);
 
 	p = memchr_inv(&r[1], 0, sizeof(r) - sizeof(r[0]));
-	KUNIT_EXPECT_PTR_EQ_MSG(test, p, NULL, "in test %u at %u out of bound", n, p - r);
+	KUNIT_EXPECT_PTR_EQ_MSG(test, p, NULL, "in test %u at %td out of bound", n, p - r);
 }
 
 static void cmdline_test_range(struct kunit *test)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/cpu_rmap.c
+++ linux-xilinx-zynqmp-5.15.0/lib/cpu_rmap.c
@@ -232,7 +232,8 @@
 
 	for (index = 0; index < rmap->used; index++) {
 		glue = rmap->obj[index];
-		irq_set_affinity_notifier(glue->notify.irq, NULL);
+		if (glue)
+			irq_set_affinity_notifier(glue->notify.irq, NULL);
 	}
 
 	cpu_rmap_put(rmap);
@@ -267,6 +268,7 @@
 	struct irq_glue *glue =
 		container_of(ref, struct irq_glue, notify.kref);
 
+	glue->rmap->obj[glue->index] = NULL;
 	cpu_rmap_put(glue->rmap);
 	kfree(glue);
 }
@@ -297,6 +299,7 @@
 	rc = irq_set_affinity_notifier(irq, &glue->notify);
 	if (rc) {
 		cpu_rmap_put(glue->rmap);
+		rmap->obj[glue->index] = NULL;
 		kfree(glue);
 	}
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/cpumask.c
+++ linux-xilinx-zynqmp-5.15.0/lib/cpumask.c
@@ -188,7 +188,7 @@
  */
 void __init free_bootmem_cpumask_var(cpumask_var_t mask)
 {
-	memblock_free_early(__pa(mask), cpumask_size());
+	memblock_free(__pa(mask), cpumask_size());
 }
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/crypto/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/lib/crypto/Kconfig
@@ -1,6 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 
-comment "Crypto library routines"
+menu "Crypto library routines"
 
 config CRYPTO_LIB_AES
 	tristate
@@ -9,14 +9,14 @@
 	tristate
 
 config CRYPTO_ARCH_HAVE_LIB_BLAKE2S
-	tristate
+	bool
 	help
 	  Declares whether the architecture provides an arch-specific
 	  accelerated implementation of the Blake2s library interface,
 	  either builtin or as a module.
 
 config CRYPTO_LIB_BLAKE2S_GENERIC
-	tristate
+	def_bool !CRYPTO_ARCH_HAVE_LIB_BLAKE2S
 	help
 	  This symbol can be depended upon by arch implementations of the
 	  Blake2s library interface that require the generic code as a
@@ -24,15 +24,6 @@
 	  implementation is enabled, this implementation serves the users
 	  of CRYPTO_LIB_BLAKE2S.
 
-config CRYPTO_LIB_BLAKE2S
-	tristate "BLAKE2s hash function library"
-	depends on CRYPTO_ARCH_HAVE_LIB_BLAKE2S || !CRYPTO_ARCH_HAVE_LIB_BLAKE2S
-	select CRYPTO_LIB_BLAKE2S_GENERIC if CRYPTO_ARCH_HAVE_LIB_BLAKE2S=n
-	help
-	  Enable the Blake2s library interface. This interface may be fulfilled
-	  by either the generic implementation or an arch-specific one, if one
-	  is available and enabled.
-
 config CRYPTO_ARCH_HAVE_LIB_CHACHA
 	tristate
 	help
@@ -42,7 +33,6 @@
 
 config CRYPTO_LIB_CHACHA_GENERIC
 	tristate
-	select CRYPTO_ALGAPI
 	help
 	  This symbol can be depended upon by arch implementations of the
 	  ChaCha library interface that require the generic code as a
@@ -52,6 +42,7 @@
 
 config CRYPTO_LIB_CHACHA
 	tristate "ChaCha library interface"
+	depends on CRYPTO
 	depends on CRYPTO_ARCH_HAVE_LIB_CHACHA || !CRYPTO_ARCH_HAVE_LIB_CHACHA
 	select CRYPTO_LIB_CHACHA_GENERIC if CRYPTO_ARCH_HAVE_LIB_CHACHA=n
 	help
@@ -79,6 +70,7 @@
 	tristate "Curve25519 scalar multiplication library"
 	depends on CRYPTO_ARCH_HAVE_LIB_CURVE25519 || !CRYPTO_ARCH_HAVE_LIB_CURVE25519
 	select CRYPTO_LIB_CURVE25519_GENERIC if CRYPTO_ARCH_HAVE_LIB_CURVE25519=n
+	select LIB_MEMNEQ
 	help
 	  Enable the Curve25519 library interface. This interface may be
 	  fulfilled by either the generic implementation or an arch-specific
@@ -123,11 +115,15 @@
 	tristate "ChaCha20-Poly1305 AEAD support (8-byte nonce library version)"
 	depends on CRYPTO_ARCH_HAVE_LIB_CHACHA || !CRYPTO_ARCH_HAVE_LIB_CHACHA
 	depends on CRYPTO_ARCH_HAVE_LIB_POLY1305 || !CRYPTO_ARCH_HAVE_LIB_POLY1305
+	depends on CRYPTO
 	select CRYPTO_LIB_CHACHA
 	select CRYPTO_LIB_POLY1305
+	select CRYPTO_ALGAPI
 
 config CRYPTO_LIB_SHA256
 	tristate
 
 config CRYPTO_LIB_SM4
 	tristate
+
+endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/lib/crypto/Makefile
+++ linux-xilinx-zynqmp-5.15.0/lib/crypto/Makefile
@@ -10,11 +10,10 @@
 obj-$(CONFIG_CRYPTO_LIB_ARC4)			+= libarc4.o
 libarc4-y					:= arc4.o
 
-obj-$(CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC)	+= libblake2s-generic.o
-libblake2s-generic-y				+= blake2s-generic.o
-
-obj-$(CONFIG_CRYPTO_LIB_BLAKE2S)		+= libblake2s.o
-libblake2s-y					+= blake2s.o
+# blake2s is used by the /dev/random driver which is always builtin
+obj-y						+= libblake2s.o
+libblake2s-y					:= blake2s.o
+libblake2s-$(CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC)	+= blake2s-generic.o
 
 obj-$(CONFIG_CRYPTO_LIB_CHACHA20POLY1305)	+= libchacha20poly1305.o
 libchacha20poly1305-y				+= chacha20poly1305.o
--- linux-xilinx-zynqmp-5.15.0.orig/lib/crypto/blake2s-generic.c
+++ linux-xilinx-zynqmp-5.15.0/lib/crypto/blake2s-generic.c
@@ -37,7 +37,11 @@
 	state->t[1] += (state->t[0] < inc);
 }
 
-void blake2s_compress_generic(struct blake2s_state *state,const u8 *block,
+void blake2s_compress(struct blake2s_state *state, const u8 *block,
+		      size_t nblocks, const u32 inc)
+		      __weak __alias(blake2s_compress_generic);
+
+void blake2s_compress_generic(struct blake2s_state *state, const u8 *block,
 			      size_t nblocks, const u32 inc)
 {
 	u32 m[16];
--- linux-xilinx-zynqmp-5.15.0.orig/lib/crypto/blake2s-selftest.c
+++ linux-xilinx-zynqmp-5.15.0/lib/crypto/blake2s-selftest.c
@@ -4,6 +4,8 @@
  */
 
 #include <crypto/internal/blake2s.h>
+#include <linux/kernel.h>
+#include <linux/random.h>
 #include <linux/string.h>
 
 /*
@@ -15,7 +17,6 @@
  * #include <stdio.h>
  *
  * #include <openssl/evp.h>
- * #include <openssl/hmac.h>
  *
  * #define BLAKE2S_TESTVEC_COUNT	256
  *
@@ -58,16 +59,6 @@
  *	}
  *	printf("};\n\n");
  *
- *	printf("static const u8 blake2s_hmac_testvecs[][BLAKE2S_HASH_SIZE] __initconst = {\n");
- *
- *	HMAC(EVP_blake2s256(), key, sizeof(key), buf, sizeof(buf), hash, NULL);
- *	print_vec(hash, BLAKE2S_OUTBYTES);
- *
- *	HMAC(EVP_blake2s256(), buf, sizeof(buf), key, sizeof(key), hash, NULL);
- *	print_vec(hash, BLAKE2S_OUTBYTES);
- *
- *	printf("};\n");
- *
  *	return 0;
  *}
  */
@@ -554,15 +545,6 @@
     0xd6, 0x98, 0x6b, 0x07, 0x10, 0x65, 0x52, 0x65, },
 };
 
-static const u8 blake2s_hmac_testvecs[][BLAKE2S_HASH_SIZE] __initconst = {
-  { 0xce, 0xe1, 0x57, 0x69, 0x82, 0xdc, 0xbf, 0x43, 0xad, 0x56, 0x4c, 0x70,
-    0xed, 0x68, 0x16, 0x96, 0xcf, 0xa4, 0x73, 0xe8, 0xe8, 0xfc, 0x32, 0x79,
-    0x08, 0x0a, 0x75, 0x82, 0xda, 0x3f, 0x05, 0x11, },
-  { 0x77, 0x2f, 0x0c, 0x71, 0x41, 0xf4, 0x4b, 0x2b, 0xb3, 0xc6, 0xb6, 0xf9,
-    0x60, 0xde, 0xe4, 0x52, 0x38, 0x66, 0xe8, 0xbf, 0x9b, 0x96, 0xc4, 0x9f,
-    0x60, 0xd9, 0x24, 0x37, 0x99, 0xd6, 0xec, 0x31, },
-};
-
 bool __init blake2s_selftest(void)
 {
 	u8 key[BLAKE2S_KEY_SIZE];
@@ -607,15 +589,43 @@
 		}
 	}
 
-	if (success) {
-		blake2s256_hmac(hash, buf, key, sizeof(buf), sizeof(key));
-		success &= !memcmp(hash, blake2s_hmac_testvecs[0], BLAKE2S_HASH_SIZE);
-
-		blake2s256_hmac(hash, key, buf, sizeof(key), sizeof(buf));
-		success &= !memcmp(hash, blake2s_hmac_testvecs[1], BLAKE2S_HASH_SIZE);
+	for (i = 0; i < 32; ++i) {
+		enum { TEST_ALIGNMENT = 16 };
+		u8 unaligned_block[BLAKE2S_BLOCK_SIZE + TEST_ALIGNMENT - 1]
+					__aligned(TEST_ALIGNMENT);
+		u8 blocks[BLAKE2S_BLOCK_SIZE * 2];
+		struct blake2s_state state1, state2;
+
+		get_random_bytes(blocks, sizeof(blocks));
+		get_random_bytes(&state, sizeof(state));
+
+#if defined(CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC) && \
+    defined(CONFIG_CRYPTO_ARCH_HAVE_LIB_BLAKE2S)
+		memcpy(&state1, &state, sizeof(state1));
+		memcpy(&state2, &state, sizeof(state2));
+		blake2s_compress(&state1, blocks, 2, BLAKE2S_BLOCK_SIZE);
+		blake2s_compress_generic(&state2, blocks, 2, BLAKE2S_BLOCK_SIZE);
+		if (memcmp(&state1, &state2, sizeof(state1))) {
+			pr_err("blake2s random compress self-test %d: FAIL\n",
+			       i + 1);
+			success = false;
+		}
+#endif
 
-		if (!success)
-			pr_err("blake2s256_hmac self-test: FAIL\n");
+		memcpy(&state1, &state, sizeof(state1));
+		blake2s_compress(&state1, blocks, 1, BLAKE2S_BLOCK_SIZE);
+		for (l = 1; l < TEST_ALIGNMENT; ++l) {
+			memcpy(unaligned_block + l, blocks,
+			       BLAKE2S_BLOCK_SIZE);
+			memcpy(&state2, &state, sizeof(state2));
+			blake2s_compress(&state2, unaligned_block + l, 1,
+					 BLAKE2S_BLOCK_SIZE);
+			if (memcmp(&state1, &state2, sizeof(state1))) {
+				pr_err("blake2s random compress align %d self-test %d: FAIL\n",
+				       l, i + 1);
+				success = false;
+			}
+		}
 	}
 
 	return success;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/crypto/blake2s.c
+++ linux-xilinx-zynqmp-5.15.0/lib/crypto/blake2s.c
@@ -16,63 +16,48 @@
 #include <linux/init.h>
 #include <linux/bug.h>
 
-#if IS_ENABLED(CONFIG_CRYPTO_ARCH_HAVE_LIB_BLAKE2S)
-#  define blake2s_compress blake2s_compress_arch
-#else
-#  define blake2s_compress blake2s_compress_generic
-#endif
+static inline void blake2s_set_lastblock(struct blake2s_state *state)
+{
+	state->f[0] = -1;
+}
 
 void blake2s_update(struct blake2s_state *state, const u8 *in, size_t inlen)
 {
-	__blake2s_update(state, in, inlen, blake2s_compress);
+	const size_t fill = BLAKE2S_BLOCK_SIZE - state->buflen;
+
+	if (unlikely(!inlen))
+		return;
+	if (inlen > fill) {
+		memcpy(state->buf + state->buflen, in, fill);
+		blake2s_compress(state, state->buf, 1, BLAKE2S_BLOCK_SIZE);
+		state->buflen = 0;
+		in += fill;
+		inlen -= fill;
+	}
+	if (inlen > BLAKE2S_BLOCK_SIZE) {
+		const size_t nblocks = DIV_ROUND_UP(inlen, BLAKE2S_BLOCK_SIZE);
+		blake2s_compress(state, in, nblocks - 1, BLAKE2S_BLOCK_SIZE);
+		in += BLAKE2S_BLOCK_SIZE * (nblocks - 1);
+		inlen -= BLAKE2S_BLOCK_SIZE * (nblocks - 1);
+	}
+	memcpy(state->buf + state->buflen, in, inlen);
+	state->buflen += inlen;
 }
 EXPORT_SYMBOL(blake2s_update);
 
 void blake2s_final(struct blake2s_state *state, u8 *out)
 {
 	WARN_ON(IS_ENABLED(DEBUG) && !out);
-	__blake2s_final(state, out, blake2s_compress);
+	blake2s_set_lastblock(state);
+	memset(state->buf + state->buflen, 0,
+	       BLAKE2S_BLOCK_SIZE - state->buflen); /* Padding */
+	blake2s_compress(state, state->buf, 1, state->buflen);
+	cpu_to_le32_array(state->h, ARRAY_SIZE(state->h));
+	memcpy(out, state->h, state->outlen);
 	memzero_explicit(state, sizeof(*state));
 }
 EXPORT_SYMBOL(blake2s_final);
 
-void blake2s256_hmac(u8 *out, const u8 *in, const u8 *key, const size_t inlen,
-		     const size_t keylen)
-{
-	struct blake2s_state state;
-	u8 x_key[BLAKE2S_BLOCK_SIZE] __aligned(__alignof__(u32)) = { 0 };
-	u8 i_hash[BLAKE2S_HASH_SIZE] __aligned(__alignof__(u32));
-	int i;
-
-	if (keylen > BLAKE2S_BLOCK_SIZE) {
-		blake2s_init(&state, BLAKE2S_HASH_SIZE);
-		blake2s_update(&state, key, keylen);
-		blake2s_final(&state, x_key);
-	} else
-		memcpy(x_key, key, keylen);
-
-	for (i = 0; i < BLAKE2S_BLOCK_SIZE; ++i)
-		x_key[i] ^= 0x36;
-
-	blake2s_init(&state, BLAKE2S_HASH_SIZE);
-	blake2s_update(&state, x_key, BLAKE2S_BLOCK_SIZE);
-	blake2s_update(&state, in, inlen);
-	blake2s_final(&state, i_hash);
-
-	for (i = 0; i < BLAKE2S_BLOCK_SIZE; ++i)
-		x_key[i] ^= 0x5c ^ 0x36;
-
-	blake2s_init(&state, BLAKE2S_HASH_SIZE);
-	blake2s_update(&state, x_key, BLAKE2S_BLOCK_SIZE);
-	blake2s_update(&state, i_hash, BLAKE2S_HASH_SIZE);
-	blake2s_final(&state, i_hash);
-
-	memcpy(out, i_hash, BLAKE2S_HASH_SIZE);
-	memzero_explicit(x_key, BLAKE2S_BLOCK_SIZE);
-	memzero_explicit(i_hash, BLAKE2S_HASH_SIZE);
-}
-EXPORT_SYMBOL(blake2s256_hmac);
-
 static int __init blake2s_mod_init(void)
 {
 	if (!IS_ENABLED(CONFIG_CRYPTO_MANAGER_DISABLE_TESTS) &&
@@ -81,12 +66,7 @@
 	return 0;
 }
 
-static void __exit blake2s_mod_exit(void)
-{
-}
-
 module_init(blake2s_mod_init);
-module_exit(blake2s_mod_exit);
 MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("BLAKE2s hash function");
 MODULE_AUTHOR("Jason A. Donenfeld <Jason@zx2c4.com>");
--- linux-xilinx-zynqmp-5.15.0.orig/lib/crypto/sm4.c
+++ linux-xilinx-zynqmp-5.15.0/lib/crypto/sm4.c
@@ -15,7 +15,7 @@
 	0xa3b1bac6, 0x56aa3350, 0x677d9197, 0xb27022dc
 };
 
-static const u32 __cacheline_aligned ck[32] = {
+static const u32 ____cacheline_aligned ck[32] = {
 	0x00070e15, 0x1c232a31, 0x383f464d, 0x545b6269,
 	0x70777e85, 0x8c939aa1, 0xa8afb6bd, 0xc4cbd2d9,
 	0xe0e7eef5, 0xfc030a11, 0x181f262d, 0x343b4249,
@@ -26,7 +26,7 @@
 	0x10171e25, 0x2c333a41, 0x484f565d, 0x646b7279
 };
 
-static const u8 __cacheline_aligned sbox[256] = {
+static const u8 ____cacheline_aligned sbox[256] = {
 	0xd6, 0x90, 0xe9, 0xfe, 0xcc, 0xe1, 0x3d, 0xb7,
 	0x16, 0xb6, 0x14, 0xc2, 0x28, 0xfb, 0x2c, 0x05,
 	0x2b, 0x67, 0x9a, 0x76, 0x2a, 0xbe, 0x04, 0xc3,
--- linux-xilinx-zynqmp-5.15.0.orig/lib/debugobjects.c
+++ linux-xilinx-zynqmp-5.15.0/lib/debugobjects.c
@@ -129,7 +129,7 @@
 
 static void fill_pool(void)
 {
-	gfp_t gfp = GFP_ATOMIC | __GFP_NORETRY | __GFP_NOWARN;
+	gfp_t gfp = __GFP_HIGH | __GFP_NOWARN;
 	struct debug_obj *obj;
 	unsigned long flags;
 
@@ -144,13 +144,14 @@
 	 * READ_ONCE()s pair with the WRITE_ONCE()s in pool_lock critical
 	 * sections.
 	 */
-	while (READ_ONCE(obj_nr_tofree) && (READ_ONCE(obj_pool_free) < obj_pool_min_free)) {
+	while (READ_ONCE(obj_nr_tofree) &&
+	       READ_ONCE(obj_pool_free) < debug_objects_pool_min_level) {
 		raw_spin_lock_irqsave(&pool_lock, flags);
 		/*
 		 * Recheck with the lock held as the worker thread might have
 		 * won the race and freed the global free list already.
 		 */
-		while (obj_nr_tofree && (obj_pool_free < obj_pool_min_free)) {
+		while (obj_nr_tofree && (obj_pool_free < debug_objects_pool_min_level)) {
 			obj = hlist_entry(obj_to_free.first, typeof(*obj), node);
 			hlist_del(&obj->node);
 			WRITE_ONCE(obj_nr_tofree, obj_nr_tofree - 1);
@@ -219,10 +220,6 @@
 	return obj;
 }
 
-/*
- * Allocate a new object. If the pool is empty, switch off the debugger.
- * Must be called with interrupts disabled.
- */
 static struct debug_obj *
 alloc_object(void *addr, struct debug_bucket *b, const struct debug_obj_descr *descr)
 {
@@ -440,6 +437,7 @@
 	struct debug_percpu_free *percpu_pool;
 	struct hlist_node *tmp;
 	struct debug_obj *obj;
+	unsigned long flags;
 
 	/* Remote access is safe as the CPU is dead already */
 	percpu_pool = per_cpu_ptr(&percpu_obj_pool, cpu);
@@ -447,6 +445,12 @@
 		hlist_del(&obj->node);
 		kmem_cache_free(obj_cache, obj);
 	}
+
+	raw_spin_lock_irqsave(&pool_lock, flags);
+	obj_pool_used -= percpu_pool->obj_free;
+	debug_objects_freed += percpu_pool->obj_free;
+	raw_spin_unlock_irqrestore(&pool_lock, flags);
+
 	percpu_pool->obj_free = 0;
 
 	return 0;
@@ -498,6 +502,15 @@
 	const struct debug_obj_descr *descr = obj->descr;
 	static int limit;
 
+	/*
+	 * Don't report if lookup_object_or_alloc() by the current thread
+	 * failed because lookup_object_or_alloc()/debug_objects_oom() by a
+	 * concurrent thread turned off debug_objects_enabled and cleared
+	 * the hash buckets.
+	 */
+	if (!debug_objects_enabled)
+		return;
+
 	if (limit < 5 && descr != descr_test) {
 		void *hint = descr->debug_hint ?
 			descr->debug_hint(obj->object) : NULL;
@@ -548,13 +561,50 @@
 	WARN_ON(1);
 }
 
+static struct debug_obj *lookup_object_or_alloc(void *addr, struct debug_bucket *b,
+						const struct debug_obj_descr *descr,
+						bool onstack, bool alloc_ifstatic)
+{
+	struct debug_obj *obj = lookup_object(addr, b);
+	enum debug_obj_state state = ODEBUG_STATE_NONE;
+
+	if (likely(obj))
+		return obj;
+
+	/*
+	 * debug_object_init() unconditionally allocates untracked
+	 * objects. It does not matter whether it is a static object or
+	 * not.
+	 *
+	 * debug_object_assert_init() and debug_object_activate() allow
+	 * allocation only if the descriptor callback confirms that the
+	 * object is static and considered initialized. For non-static
+	 * objects the allocation needs to be done from the fixup callback.
+	 */
+	if (unlikely(alloc_ifstatic)) {
+		if (!descr->is_static_object || !descr->is_static_object(addr))
+			return ERR_PTR(-ENOENT);
+		/* Statically allocated objects are considered initialized */
+		state = ODEBUG_STATE_INIT;
+	}
+
+	obj = alloc_object(addr, b, descr);
+	if (likely(obj)) {
+		obj->state = state;
+		debug_object_is_on_stack(addr, onstack);
+		return obj;
+	}
+
+	/* Out of memory. Do the cleanup outside of the locked region */
+	debug_objects_enabled = 0;
+	return NULL;
+}
+
 static void
 __debug_object_init(void *addr, const struct debug_obj_descr *descr, int onstack)
 {
-	enum debug_obj_state state;
-	bool check_stack = false;
+	struct debug_obj *obj, o;
 	struct debug_bucket *db;
-	struct debug_obj *obj;
 	unsigned long flags;
 
 	/*
@@ -568,16 +618,11 @@
 
 	raw_spin_lock_irqsave(&db->lock, flags);
 
-	obj = lookup_object(addr, db);
-	if (!obj) {
-		obj = alloc_object(addr, db, descr);
-		if (!obj) {
-			debug_objects_enabled = 0;
-			raw_spin_unlock_irqrestore(&db->lock, flags);
-			debug_objects_oom();
-			return;
-		}
-		check_stack = true;
+	obj = lookup_object_or_alloc(addr, db, descr, onstack, false);
+	if (unlikely(!obj)) {
+		raw_spin_unlock_irqrestore(&db->lock, flags);
+		debug_objects_oom();
+		return;
 	}
 
 	switch (obj->state) {
@@ -585,26 +630,18 @@
 	case ODEBUG_STATE_INIT:
 	case ODEBUG_STATE_INACTIVE:
 		obj->state = ODEBUG_STATE_INIT;
-		break;
-
-	case ODEBUG_STATE_ACTIVE:
-		state = obj->state;
-		raw_spin_unlock_irqrestore(&db->lock, flags);
-		debug_print_object(obj, "init");
-		debug_object_fixup(descr->fixup_init, addr, state);
-		return;
-
-	case ODEBUG_STATE_DESTROYED:
 		raw_spin_unlock_irqrestore(&db->lock, flags);
-		debug_print_object(obj, "init");
 		return;
 	default:
 		break;
 	}
 
+	o = *obj;
 	raw_spin_unlock_irqrestore(&db->lock, flags);
-	if (check_stack)
-		debug_object_is_on_stack(addr, onstack);
+	debug_print_object(&o, "init");
+
+	if (o.state == ODEBUG_STATE_ACTIVE)
+		debug_object_fixup(descr->fixup_init, addr, o.state);
 }
 
 /**
@@ -644,14 +681,10 @@
  */
 int debug_object_activate(void *addr, const struct debug_obj_descr *descr)
 {
-	enum debug_obj_state state;
+	struct debug_obj o = { .object = addr, .state = ODEBUG_STATE_NOTAVAILABLE, .descr = descr };
 	struct debug_bucket *db;
 	struct debug_obj *obj;
 	unsigned long flags;
-	int ret;
-	struct debug_obj o = { .object = addr,
-			       .state = ODEBUG_STATE_NOTAVAILABLE,
-			       .descr = descr };
 
 	if (!debug_objects_enabled)
 		return 0;
@@ -660,58 +693,39 @@
 
 	raw_spin_lock_irqsave(&db->lock, flags);
 
-	obj = lookup_object(addr, db);
-	if (obj) {
-		bool print_object = false;
-
+	obj = lookup_object_or_alloc(addr, db, descr, false, true);
+	if (unlikely(!obj)) {
+		raw_spin_unlock_irqrestore(&db->lock, flags);
+		debug_objects_oom();
+		return 0;
+	} else if (likely(!IS_ERR(obj))) {
 		switch (obj->state) {
-		case ODEBUG_STATE_INIT:
-		case ODEBUG_STATE_INACTIVE:
-			obj->state = ODEBUG_STATE_ACTIVE;
-			ret = 0;
-			break;
-
 		case ODEBUG_STATE_ACTIVE:
-			state = obj->state;
-			raw_spin_unlock_irqrestore(&db->lock, flags);
-			debug_print_object(obj, "activate");
-			ret = debug_object_fixup(descr->fixup_activate, addr, state);
-			return ret ? 0 : -EINVAL;
-
 		case ODEBUG_STATE_DESTROYED:
-			print_object = true;
-			ret = -EINVAL;
+			o = *obj;
 			break;
+		case ODEBUG_STATE_INIT:
+		case ODEBUG_STATE_INACTIVE:
+			obj->state = ODEBUG_STATE_ACTIVE;
+			fallthrough;
 		default:
-			ret = 0;
-			break;
+			raw_spin_unlock_irqrestore(&db->lock, flags);
+			return 0;
 		}
-		raw_spin_unlock_irqrestore(&db->lock, flags);
-		if (print_object)
-			debug_print_object(obj, "activate");
-		return ret;
 	}
 
 	raw_spin_unlock_irqrestore(&db->lock, flags);
+	debug_print_object(&o, "activate");
 
-	/*
-	 * We are here when a static object is activated. We
-	 * let the type specific code confirm whether this is
-	 * true or not. if true, we just make sure that the
-	 * static object is tracked in the object tracker. If
-	 * not, this must be a bug, so we try to fix it up.
-	 */
-	if (descr->is_static_object && descr->is_static_object(addr)) {
-		/* track this static object */
-		debug_object_init(addr, descr);
-		debug_object_activate(addr, descr);
-	} else {
-		debug_print_object(&o, "activate");
-		ret = debug_object_fixup(descr->fixup_activate, addr,
-					ODEBUG_STATE_NOTAVAILABLE);
-		return ret ? 0 : -EINVAL;
+	switch (o.state) {
+	case ODEBUG_STATE_ACTIVE:
+	case ODEBUG_STATE_NOTAVAILABLE:
+		if (debug_object_fixup(descr->fixup_activate, addr, o.state))
+			return 0;
+		fallthrough;
+	default:
+		return -EINVAL;
 	}
-	return 0;
 }
 EXPORT_SYMBOL_GPL(debug_object_activate);
 
@@ -722,10 +736,10 @@
  */
 void debug_object_deactivate(void *addr, const struct debug_obj_descr *descr)
 {
+	struct debug_obj o = { .object = addr, .state = ODEBUG_STATE_NOTAVAILABLE, .descr = descr };
 	struct debug_bucket *db;
 	struct debug_obj *obj;
 	unsigned long flags;
-	bool print_object = false;
 
 	if (!debug_objects_enabled)
 		return;
@@ -737,33 +751,24 @@
 	obj = lookup_object(addr, db);
 	if (obj) {
 		switch (obj->state) {
+		case ODEBUG_STATE_DESTROYED:
+			break;
 		case ODEBUG_STATE_INIT:
 		case ODEBUG_STATE_INACTIVE:
 		case ODEBUG_STATE_ACTIVE:
-			if (!obj->astate)
-				obj->state = ODEBUG_STATE_INACTIVE;
-			else
-				print_object = true;
-			break;
-
-		case ODEBUG_STATE_DESTROYED:
-			print_object = true;
-			break;
+			if (obj->astate)
+				break;
+			obj->state = ODEBUG_STATE_INACTIVE;
+			fallthrough;
 		default:
-			break;
+			raw_spin_unlock_irqrestore(&db->lock, flags);
+			return;
 		}
+		o = *obj;
 	}
 
 	raw_spin_unlock_irqrestore(&db->lock, flags);
-	if (!obj) {
-		struct debug_obj o = { .object = addr,
-				       .state = ODEBUG_STATE_NOTAVAILABLE,
-				       .descr = descr };
-
-		debug_print_object(&o, "deactivate");
-	} else if (print_object) {
-		debug_print_object(obj, "deactivate");
-	}
+	debug_print_object(&o, "deactivate");
 }
 EXPORT_SYMBOL_GPL(debug_object_deactivate);
 
@@ -774,11 +779,9 @@
  */
 void debug_object_destroy(void *addr, const struct debug_obj_descr *descr)
 {
-	enum debug_obj_state state;
+	struct debug_obj *obj, o;
 	struct debug_bucket *db;
-	struct debug_obj *obj;
 	unsigned long flags;
-	bool print_object = false;
 
 	if (!debug_objects_enabled)
 		return;
@@ -788,32 +791,31 @@
 	raw_spin_lock_irqsave(&db->lock, flags);
 
 	obj = lookup_object(addr, db);
-	if (!obj)
-		goto out_unlock;
+	if (!obj) {
+		raw_spin_unlock_irqrestore(&db->lock, flags);
+		return;
+	}
 
 	switch (obj->state) {
+	case ODEBUG_STATE_ACTIVE:
+	case ODEBUG_STATE_DESTROYED:
+		break;
 	case ODEBUG_STATE_NONE:
 	case ODEBUG_STATE_INIT:
 	case ODEBUG_STATE_INACTIVE:
 		obj->state = ODEBUG_STATE_DESTROYED;
-		break;
-	case ODEBUG_STATE_ACTIVE:
-		state = obj->state;
+		fallthrough;
+	default:
 		raw_spin_unlock_irqrestore(&db->lock, flags);
-		debug_print_object(obj, "destroy");
-		debug_object_fixup(descr->fixup_destroy, addr, state);
 		return;
-
-	case ODEBUG_STATE_DESTROYED:
-		print_object = true;
-		break;
-	default:
-		break;
 	}
-out_unlock:
+
+	o = *obj;
 	raw_spin_unlock_irqrestore(&db->lock, flags);
-	if (print_object)
-		debug_print_object(obj, "destroy");
+	debug_print_object(&o, "destroy");
+
+	if (o.state == ODEBUG_STATE_ACTIVE)
+		debug_object_fixup(descr->fixup_destroy, addr, o.state);
 }
 EXPORT_SYMBOL_GPL(debug_object_destroy);
 
@@ -824,9 +826,8 @@
  */
 void debug_object_free(void *addr, const struct debug_obj_descr *descr)
 {
-	enum debug_obj_state state;
+	struct debug_obj *obj, o;
 	struct debug_bucket *db;
-	struct debug_obj *obj;
 	unsigned long flags;
 
 	if (!debug_objects_enabled)
@@ -837,24 +838,26 @@
 	raw_spin_lock_irqsave(&db->lock, flags);
 
 	obj = lookup_object(addr, db);
-	if (!obj)
-		goto out_unlock;
+	if (!obj) {
+		raw_spin_unlock_irqrestore(&db->lock, flags);
+		return;
+	}
 
 	switch (obj->state) {
 	case ODEBUG_STATE_ACTIVE:
-		state = obj->state;
-		raw_spin_unlock_irqrestore(&db->lock, flags);
-		debug_print_object(obj, "free");
-		debug_object_fixup(descr->fixup_free, addr, state);
-		return;
+		break;
 	default:
 		hlist_del(&obj->node);
 		raw_spin_unlock_irqrestore(&db->lock, flags);
 		free_object(obj);
 		return;
 	}
-out_unlock:
+
+	o = *obj;
 	raw_spin_unlock_irqrestore(&db->lock, flags);
+	debug_print_object(&o, "free");
+
+	debug_object_fixup(descr->fixup_free, addr, o.state);
 }
 EXPORT_SYMBOL_GPL(debug_object_free);
 
@@ -865,6 +868,7 @@
  */
 void debug_object_assert_init(void *addr, const struct debug_obj_descr *descr)
 {
+	struct debug_obj o = { .object = addr, .state = ODEBUG_STATE_NOTAVAILABLE, .descr = descr };
 	struct debug_bucket *db;
 	struct debug_obj *obj;
 	unsigned long flags;
@@ -875,31 +879,20 @@
 	db = get_bucket((unsigned long) addr);
 
 	raw_spin_lock_irqsave(&db->lock, flags);
+	obj = lookup_object_or_alloc(addr, db, descr, false, true);
+	raw_spin_unlock_irqrestore(&db->lock, flags);
+	if (likely(!IS_ERR_OR_NULL(obj)))
+		return;
 
-	obj = lookup_object(addr, db);
+	/* If NULL the allocation has hit OOM */
 	if (!obj) {
-		struct debug_obj o = { .object = addr,
-				       .state = ODEBUG_STATE_NOTAVAILABLE,
-				       .descr = descr };
-
-		raw_spin_unlock_irqrestore(&db->lock, flags);
-		/*
-		 * Maybe the object is static, and we let the type specific
-		 * code confirm. Track this static object if true, else invoke
-		 * fixup.
-		 */
-		if (descr->is_static_object && descr->is_static_object(addr)) {
-			/* Track this static object */
-			debug_object_init(addr, descr);
-		} else {
-			debug_print_object(&o, "assert_init");
-			debug_object_fixup(descr->fixup_assert_init, addr,
-					   ODEBUG_STATE_NOTAVAILABLE);
-		}
+		debug_objects_oom();
 		return;
 	}
 
-	raw_spin_unlock_irqrestore(&db->lock, flags);
+	/* Object is neither tracked nor static. It's not initialized. */
+	debug_print_object(&o, "assert_init");
+	debug_object_fixup(descr->fixup_assert_init, addr, ODEBUG_STATE_NOTAVAILABLE);
 }
 EXPORT_SYMBOL_GPL(debug_object_assert_init);
 
@@ -914,10 +907,10 @@
 debug_object_active_state(void *addr, const struct debug_obj_descr *descr,
 			  unsigned int expect, unsigned int next)
 {
+	struct debug_obj o = { .object = addr, .state = ODEBUG_STATE_NOTAVAILABLE, .descr = descr };
 	struct debug_bucket *db;
 	struct debug_obj *obj;
 	unsigned long flags;
-	bool print_object = false;
 
 	if (!debug_objects_enabled)
 		return;
@@ -930,28 +923,19 @@
 	if (obj) {
 		switch (obj->state) {
 		case ODEBUG_STATE_ACTIVE:
-			if (obj->astate == expect)
-				obj->astate = next;
-			else
-				print_object = true;
-			break;
-
+			if (obj->astate != expect)
+				break;
+			obj->astate = next;
+			raw_spin_unlock_irqrestore(&db->lock, flags);
+			return;
 		default:
-			print_object = true;
 			break;
 		}
+		o = *obj;
 	}
 
 	raw_spin_unlock_irqrestore(&db->lock, flags);
-	if (!obj) {
-		struct debug_obj o = { .object = addr,
-				       .state = ODEBUG_STATE_NOTAVAILABLE,
-				       .descr = descr };
-
-		debug_print_object(&o, "active_state");
-	} else if (print_object) {
-		debug_print_object(obj, "active_state");
-	}
+	debug_print_object(&o, "active_state");
 }
 EXPORT_SYMBOL_GPL(debug_object_active_state);
 
@@ -959,12 +943,10 @@
 static void __debug_check_no_obj_freed(const void *address, unsigned long size)
 {
 	unsigned long flags, oaddr, saddr, eaddr, paddr, chunks;
-	const struct debug_obj_descr *descr;
-	enum debug_obj_state state;
+	int cnt, objs_checked = 0;
+	struct debug_obj *obj, o;
 	struct debug_bucket *db;
 	struct hlist_node *tmp;
-	struct debug_obj *obj;
-	int cnt, objs_checked = 0;
 
 	saddr = (unsigned long) address;
 	eaddr = saddr + size;
@@ -986,12 +968,10 @@
 
 			switch (obj->state) {
 			case ODEBUG_STATE_ACTIVE:
-				descr = obj->descr;
-				state = obj->state;
+				o = *obj;
 				raw_spin_unlock_irqrestore(&db->lock, flags);
-				debug_print_object(obj, "free");
-				debug_object_fixup(descr->fixup_free,
-						   (void *) oaddr, state);
+				debug_print_object(&o, "free");
+				debug_object_fixup(o.descr->fixup_free, (void *)oaddr, o.state);
 				goto repeat;
 			default:
 				hlist_del(&obj->node);
@@ -1321,6 +1301,8 @@
 		hlist_add_head(&obj->node, &objects);
 	}
 
+	debug_objects_allocated += i;
+
 	/*
 	 * debug_objects_mem_init() is now called early that only one CPU is up
 	 * and interrupts have been disabled, so it is safe to replace the
@@ -1389,6 +1371,7 @@
 		debug_objects_enabled = 0;
 		kmem_cache_destroy(obj_cache);
 		pr_warn("out of memory.\n");
+		return;
 	} else
 		debug_objects_selftest();
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/decompress_bunzip2.c
+++ linux-xilinx-zynqmp-5.15.0/lib/decompress_bunzip2.c
@@ -232,7 +232,8 @@
 	   RUNB) */
 	symCount = symTotal+2;
 	for (j = 0; j < groupCount; j++) {
-		unsigned char length[MAX_SYMBOLS], temp[MAX_HUFCODE_BITS+1];
+		unsigned char length[MAX_SYMBOLS];
+		unsigned short temp[MAX_HUFCODE_BITS+1];
 		int	minLen,	maxLen, pp;
 		/* Read Huffman code lengths for each symbol.  They're
 		   stored in a way similar to mtf; record a starting
--- linux-xilinx-zynqmp-5.15.0.orig/lib/decompress_unxz.c
+++ linux-xilinx-zynqmp-5.15.0/lib/decompress_unxz.c
@@ -167,7 +167,7 @@
  * memeq and memzero are not used much and any remotely sane implementation
  * is fast enough. memcpy/memmove speed matters in multi-call mode, but
  * the kernel image is decompressed in single-call mode, in which only
- * memcpy speed can matter and only if there is a lot of uncompressible data
+ * memmove speed can matter and only if there is a lot of uncompressible data
  * (LZMA2 stores uncompressible chunks in uncompressed form). Thus, the
  * functions below should just be kept small; it's probably not worth
  * optimizing for speed.
--- linux-xilinx-zynqmp-5.15.0.orig/lib/dim/dim.c
+++ linux-xilinx-zynqmp-5.15.0/lib/dim/dim.c
@@ -54,7 +54,7 @@
 }
 EXPORT_SYMBOL(dim_park_tired);
 
-void dim_calc_stats(struct dim_sample *start, struct dim_sample *end,
+bool dim_calc_stats(struct dim_sample *start, struct dim_sample *end,
 		    struct dim_stats *curr_stats)
 {
 	/* u32 holds up to 71 minutes, should be enough */
@@ -66,7 +66,7 @@
 			     start->comp_ctr);
 
 	if (!delta_us)
-		return;
+		return false;
 
 	curr_stats->ppms = DIV_ROUND_UP(npkts * USEC_PER_MSEC, delta_us);
 	curr_stats->bpms = DIV_ROUND_UP(nbytes * USEC_PER_MSEC, delta_us);
@@ -79,5 +79,6 @@
 	else
 		curr_stats->cpe_ratio = 0;
 
+	return true;
 }
 EXPORT_SYMBOL(dim_calc_stats);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/dim/net_dim.c
+++ linux-xilinx-zynqmp-5.15.0/lib/dim/net_dim.c
@@ -12,41 +12,41 @@
  *        Each profile size must be of NET_DIM_PARAMS_NUM_PROFILES
  */
 #define NET_DIM_PARAMS_NUM_PROFILES 5
-#define NET_DIM_DEFAULT_RX_CQ_MODERATION_PKTS_FROM_EQE 256
-#define NET_DIM_DEFAULT_TX_CQ_MODERATION_PKTS_FROM_EQE 128
+#define NET_DIM_DEFAULT_RX_CQ_PKTS_FROM_EQE 256
+#define NET_DIM_DEFAULT_TX_CQ_PKTS_FROM_EQE 128
 #define NET_DIM_DEF_PROFILE_CQE 1
 #define NET_DIM_DEF_PROFILE_EQE 1
 
 #define NET_DIM_RX_EQE_PROFILES { \
-	{1,   NET_DIM_DEFAULT_RX_CQ_MODERATION_PKTS_FROM_EQE}, \
-	{8,   NET_DIM_DEFAULT_RX_CQ_MODERATION_PKTS_FROM_EQE}, \
-	{64,  NET_DIM_DEFAULT_RX_CQ_MODERATION_PKTS_FROM_EQE}, \
-	{128, NET_DIM_DEFAULT_RX_CQ_MODERATION_PKTS_FROM_EQE}, \
-	{256, NET_DIM_DEFAULT_RX_CQ_MODERATION_PKTS_FROM_EQE}, \
+	{.usec = 1,   .pkts = NET_DIM_DEFAULT_RX_CQ_PKTS_FROM_EQE,}, \
+	{.usec = 8,   .pkts = NET_DIM_DEFAULT_RX_CQ_PKTS_FROM_EQE,}, \
+	{.usec = 64,  .pkts = NET_DIM_DEFAULT_RX_CQ_PKTS_FROM_EQE,}, \
+	{.usec = 128, .pkts = NET_DIM_DEFAULT_RX_CQ_PKTS_FROM_EQE,}, \
+	{.usec = 256, .pkts = NET_DIM_DEFAULT_RX_CQ_PKTS_FROM_EQE,}  \
 }
 
 #define NET_DIM_RX_CQE_PROFILES { \
-	{2,  256},             \
-	{8,  128},             \
-	{16, 64},              \
-	{32, 64},              \
-	{64, 64}               \
+	{.usec = 2,  .pkts = 256,},             \
+	{.usec = 8,  .pkts = 128,},             \
+	{.usec = 16, .pkts = 64,},              \
+	{.usec = 32, .pkts = 64,},              \
+	{.usec = 64, .pkts = 64,}               \
 }
 
 #define NET_DIM_TX_EQE_PROFILES { \
-	{1,   NET_DIM_DEFAULT_TX_CQ_MODERATION_PKTS_FROM_EQE},  \
-	{8,   NET_DIM_DEFAULT_TX_CQ_MODERATION_PKTS_FROM_EQE},  \
-	{32,  NET_DIM_DEFAULT_TX_CQ_MODERATION_PKTS_FROM_EQE},  \
-	{64,  NET_DIM_DEFAULT_TX_CQ_MODERATION_PKTS_FROM_EQE},  \
-	{128, NET_DIM_DEFAULT_TX_CQ_MODERATION_PKTS_FROM_EQE}   \
+	{.usec = 1,   .pkts = NET_DIM_DEFAULT_TX_CQ_PKTS_FROM_EQE,},  \
+	{.usec = 8,   .pkts = NET_DIM_DEFAULT_TX_CQ_PKTS_FROM_EQE,},  \
+	{.usec = 32,  .pkts = NET_DIM_DEFAULT_TX_CQ_PKTS_FROM_EQE,},  \
+	{.usec = 64,  .pkts = NET_DIM_DEFAULT_TX_CQ_PKTS_FROM_EQE,},  \
+	{.usec = 128, .pkts = NET_DIM_DEFAULT_TX_CQ_PKTS_FROM_EQE,}   \
 }
 
 #define NET_DIM_TX_CQE_PROFILES { \
-	{5,  128},  \
-	{8,  64},  \
-	{16, 32},  \
-	{32, 32},  \
-	{64, 32}   \
+	{.usec = 5,  .pkts = 128,},  \
+	{.usec = 8,  .pkts = 64,},  \
+	{.usec = 16, .pkts = 32,},  \
+	{.usec = 32, .pkts = 32,},  \
+	{.usec = 64, .pkts = 32,}   \
 }
 
 static const struct dim_cq_moder
@@ -227,7 +227,8 @@
 				  dim->start_sample.event_ctr);
 		if (nevents < DIM_NEVENTS)
 			break;
-		dim_calc_stats(&dim->start_sample, &end_sample, &curr_stats);
+		if (!dim_calc_stats(&dim->start_sample, &end_sample, &curr_stats))
+			break;
 		if (net_dim_decision(&curr_stats, dim)) {
 			dim->state = DIM_APPLY_NEW_PROFILE;
 			schedule_work(&dim->work);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/dim/rdma_dim.c
+++ linux-xilinx-zynqmp-5.15.0/lib/dim/rdma_dim.c
@@ -88,7 +88,8 @@
 		nevents = curr_sample->event_ctr - dim->start_sample.event_ctr;
 		if (nevents < DIM_NEVENTS)
 			break;
-		dim_calc_stats(&dim->start_sample, curr_sample, &curr_stats);
+		if (!dim_calc_stats(&dim->start_sample, curr_sample, &curr_stats))
+			break;
 		if (rdma_dim_decision(&curr_stats, dim)) {
 			dim->state = DIM_APPLY_NEW_PROFILE;
 			schedule_work(&dim->work);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/dynamic_debug.c
+++ linux-xilinx-zynqmp-5.15.0/lib/dynamic_debug.c
@@ -207,10 +207,11 @@
 				continue;
 #ifdef CONFIG_JUMP_LABEL
 			if (dp->flags & _DPRINTK_FLAGS_PRINT) {
-				if (!(modifiers->flags & _DPRINTK_FLAGS_PRINT))
+				if (!(newflags & _DPRINTK_FLAGS_PRINT))
 					static_branch_disable(&dp->key.dd_key_true);
-			} else if (modifiers->flags & _DPRINTK_FLAGS_PRINT)
+			} else if (newflags & _DPRINTK_FLAGS_PRINT) {
 				static_branch_enable(&dp->key.dd_key_true);
+			}
 #endif
 			dp->flags = newflags;
 			v2pr_info("changed %s:%d [%s]%s =%s\n",
@@ -259,7 +260,11 @@
 		} else {
 			for (end = buf; *end && !isspace(*end); end++)
 				;
-			BUG_ON(end == buf);
+			if (end == buf) {
+				pr_err("parse err after word:%d=%s\n", nwords,
+				       nwords ? words[nwords - 1] : "<none>");
+				return -EINVAL;
+			}
 		}
 
 		/* `buf' is start of word, `end' is one past its end */
@@ -379,10 +384,6 @@
 		return -EINVAL;
 	}
 
-	if (modname)
-		/* support $modname.dyndbg=<multiple queries> */
-		query->module = modname;
-
 	for (i = 0; i < nwords; i += 2) {
 		char *keyword = words[i];
 		char *arg = words[i+1];
@@ -423,6 +424,13 @@
 		if (rc)
 			return rc;
 	}
+	if (!query->module && modname)
+		/*
+		 * support $modname.dyndbg=<multiple queries>, when
+		 * not given in the query itself
+		 */
+		query->module = modname;
+
 	vpr_info_dq(query, "parsed");
 	return 0;
 }
@@ -548,35 +556,6 @@
 	return nfound;
 }
 
-/**
- * dynamic_debug_exec_queries - select and change dynamic-debug prints
- * @query: query-string described in admin-guide/dynamic-debug-howto
- * @modname: string containing module name, usually &module.mod_name
- *
- * This uses the >/proc/dynamic_debug/control reader, allowing module
- * authors to modify their dynamic-debug callsites. The modname is
- * canonically struct module.mod_name, but can also be null or a
- * module-wildcard, for example: "drm*".
- */
-int dynamic_debug_exec_queries(const char *query, const char *modname)
-{
-	int rc;
-	char *qry; /* writable copy of query */
-
-	if (!query) {
-		pr_err("non-null query/command string expected\n");
-		return -EINVAL;
-	}
-	qry = kstrndup(query, PAGE_SIZE, GFP_KERNEL);
-	if (!qry)
-		return -ENOMEM;
-
-	rc = ddebug_exec_queries(qry, modname);
-	kfree(qry);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(dynamic_debug_exec_queries);
-
 #define PREFIX_SIZE 64
 
 static int remaining(int wrote)
@@ -762,6 +741,18 @@
 __setup("ddebug_query=", ddebug_setup_query);
 
 /*
+ * Install a noop handler to make dyndbg look like a normal kernel cli param.
+ * This avoids warnings about dyndbg being an unknown cli param when supplied
+ * by a user.
+ */
+static __init int dyndbg_setup(char *str)
+{
+	return 1;
+}
+
+__setup("dyndbg=", dyndbg_setup);
+
+/*
  * File_ops->write method for <debugfs>/dynamic_debug/control.  Gathers the
  * command text from userspace, parses and executes it.
  */
--- linux-xilinx-zynqmp-5.15.0.orig/lib/errname.c
+++ linux-xilinx-zynqmp-5.15.0/lib/errname.c
@@ -21,6 +21,7 @@
 	E(EADDRNOTAVAIL),
 	E(EADV),
 	E(EAFNOSUPPORT),
+	E(EAGAIN), /* EWOULDBLOCK */
 	E(EALREADY),
 	E(EBADE),
 	E(EBADF),
@@ -31,15 +32,17 @@
 	E(EBADSLT),
 	E(EBFONT),
 	E(EBUSY),
-#ifdef ECANCELLED
-	E(ECANCELLED),
-#endif
+	E(ECANCELED), /* ECANCELLED */
 	E(ECHILD),
 	E(ECHRNG),
 	E(ECOMM),
 	E(ECONNABORTED),
+	E(ECONNREFUSED), /* EREFUSED */
 	E(ECONNRESET),
+	E(EDEADLK), /* EDEADLOCK */
+#if EDEADLK != EDEADLOCK /* mips, sparc, powerpc */
 	E(EDEADLOCK),
+#endif
 	E(EDESTADDRREQ),
 	E(EDOM),
 	E(EDOTDOT),
@@ -108,9 +111,6 @@
 	E(ENOSPC),
 	E(ENOSR),
 	E(ENOSTR),
-#ifdef ENOSYM
-	E(ENOSYM),
-#endif
 	E(ENOSYS),
 	E(ENOTBLK),
 	E(ENOTCONN),
@@ -141,9 +141,6 @@
 #endif
 	E(EREMOTE),
 	E(EREMOTEIO),
-#ifdef EREMOTERELEASE
-	E(EREMOTERELEASE),
-#endif
 	E(ERESTART),
 	E(ERFKILL),
 	E(EROFS),
@@ -166,14 +163,17 @@
 	E(EUSERS),
 	E(EXDEV),
 	E(EXFULL),
-
-	E(ECANCELED), /* ECANCELLED */
-	E(EAGAIN), /* EWOULDBLOCK */
-	E(ECONNREFUSED), /* EREFUSED */
-	E(EDEADLK), /* EDEADLOCK */
 };
 #undef E
 
+#ifdef EREFUSED /* parisc */
+static_assert(EREFUSED == ECONNREFUSED);
+#endif
+#ifdef ECANCELLED /* parisc */
+static_assert(ECANCELLED == ECANCELED);
+#endif
+static_assert(EAGAIN == EWOULDBLOCK); /* everywhere */
+
 #define E(err) [err - 512 + BUILD_BUG_ON_ZERO(err < 512 || err > 550)] = "-" #err
 static const char *names_512[] = {
 	E(ERESTARTSYS),
--- linux-xilinx-zynqmp-5.15.0.orig/lib/fonts/fonts.c
+++ linux-xilinx-zynqmp-5.15.0/lib/fonts/fonts.c
@@ -135,8 +135,8 @@
 		if (res > 20)
 			c += 20 - res;
 
-		if ((font_w & (1 << (f->width - 1))) &&
-		    (font_h & (1 << (f->height - 1))))
+		if ((font_w & (1U << (f->width - 1))) &&
+		    (font_h & (1U << (f->height - 1))))
 			c += 1000;
 
 		if (c > cc) {
--- linux-xilinx-zynqmp-5.15.0.orig/lib/generic-radix-tree.c
+++ linux-xilinx-zynqmp-5.15.0/lib/generic-radix-tree.c
@@ -131,6 +131,8 @@
 		if ((v = cmpxchg_release(&radix->root, r, new_root)) == r) {
 			v = new_root;
 			new_node = NULL;
+		} else {
+			new_node->children[0] = NULL;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/hexdump.c
+++ linux-xilinx-zynqmp-5.15.0/lib/hexdump.c
@@ -22,15 +22,33 @@
  *
  * hex_to_bin() converts one hex digit to its actual value or -1 in case of bad
  * input.
+ *
+ * This function is used to load cryptographic keys, so it is coded in such a
+ * way that there are no conditions or memory accesses that depend on data.
+ *
+ * Explanation of the logic:
+ * (ch - '9' - 1) is negative if ch <= '9'
+ * ('0' - 1 - ch) is negative if ch >= '0'
+ * we "and" these two values, so the result is negative if ch is in the range
+ *	'0' ... '9'
+ * we are only interested in the sign, so we do a shift ">> 8"; note that right
+ *	shift of a negative value is implementation-defined, so we cast the
+ *	value to (unsigned) before the shift --- we have 0xffffff if ch is in
+ *	the range '0' ... '9', 0 otherwise
+ * we "and" this value with (ch - '0' + 1) --- we have a value 1 ... 10 if ch is
+ *	in the range '0' ... '9', 0 otherwise
+ * we add this value to -1 --- we have a value 0 ... 9 if ch is in the range '0'
+ *	... '9', -1 otherwise
+ * the next line is similar to the previous one, but we need to decode both
+ *	uppercase and lowercase letters, so we use (ch & 0xdf), which converts
+ *	lowercase to uppercase
  */
-int hex_to_bin(char ch)
+int hex_to_bin(unsigned char ch)
 {
-	if ((ch >= '0') && (ch <= '9'))
-		return ch - '0';
-	ch = tolower(ch);
-	if ((ch >= 'a') && (ch <= 'f'))
-		return ch - 'a' + 10;
-	return -1;
+	unsigned char cu = ch & 0xdf;
+	return -1 +
+		((ch - '0' +  1) & (unsigned)((ch - '9' - 1) & ('0' - 1 - ch)) >> 8) +
+		((cu - 'A' + 11) & (unsigned)((cu - 'F' - 1) & ('A' - 1 - cu)) >> 8);
 }
 EXPORT_SYMBOL(hex_to_bin);
 
@@ -45,10 +63,13 @@
 int hex2bin(u8 *dst, const char *src, size_t count)
 {
 	while (count--) {
-		int hi = hex_to_bin(*src++);
-		int lo = hex_to_bin(*src++);
+		int hi, lo;
 
-		if ((hi < 0) || (lo < 0))
+		hi = hex_to_bin(*src++);
+		if (unlikely(hi < 0))
+			return -EINVAL;
+		lo = hex_to_bin(*src++);
+		if (unlikely(lo < 0))
 			return -EINVAL;
 
 		*dst++ = (hi << 4) | lo;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/idr.c
+++ linux-xilinx-zynqmp-5.15.0/lib/idr.c
@@ -100,7 +100,7 @@
  * @end: The maximum ID (exclusive).
  * @gfp: Memory allocation flags.
  *
- * Allocates an unused ID in the range specified by @nextid and @end.  If
+ * Allocates an unused ID in the range specified by @start and @end.  If
  * @end is <= 0, it is treated as one larger than %INT_MAX.  This allows
  * callers to use @start + N as @end as long as N is within integer range.
  * The search for an unused ID will start at the last ID allocated and will
@@ -491,7 +491,8 @@
 	struct ida_bitmap *bitmap;
 	unsigned long flags;
 
-	BUG_ON((int)id < 0);
+	if ((int)id < 0)
+		return;
 
 	xas_lock_irqsave(&xas, flags);
 	bitmap = xas_load(&xas);
@@ -507,7 +508,7 @@
 			goto delete;
 		xas_store(&xas, xa_mk_value(v));
 	} else {
-		if (!test_bit(bit, bitmap->bitmap))
+		if (!bitmap || !test_bit(bit, bitmap->bitmap))
 			goto err;
 		__clear_bit(bit, bitmap->bitmap);
 		xas_set_mark(&xas, XA_FREE_MARK);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/iov_iter.c
+++ linux-xilinx-zynqmp-5.15.0/lib/iov_iter.c
@@ -191,7 +191,7 @@
 	buf = iov->iov_base + skip;
 	copy = min(bytes, iov->iov_len - skip);
 
-	if (IS_ENABLED(CONFIG_HIGHMEM) && !fault_in_pages_writeable(buf, copy)) {
+	if (IS_ENABLED(CONFIG_HIGHMEM) && !fault_in_writeable(buf, copy)) {
 		kaddr = kmap_atomic(page);
 		from = kaddr + offset;
 
@@ -275,7 +275,7 @@
 	buf = iov->iov_base + skip;
 	copy = min(bytes, iov->iov_len - skip);
 
-	if (IS_ENABLED(CONFIG_HIGHMEM) && !fault_in_pages_readable(buf, copy)) {
+	if (IS_ENABLED(CONFIG_HIGHMEM) && !fault_in_readable(buf, copy)) {
 		kaddr = kmap_atomic(page);
 		to = kaddr + offset;
 
@@ -416,6 +416,7 @@
 		return 0;
 
 	buf->ops = &page_cache_pipe_buf_ops;
+	buf->flags = 0;
 	get_page(page);
 	buf->page = page;
 	buf->offset = offset;
@@ -430,35 +431,81 @@
 }
 
 /*
+ * fault_in_iov_iter_readable - fault in iov iterator for reading
+ * @i: iterator
+ * @size: maximum length
+ *
  * Fault in one or more iovecs of the given iov_iter, to a maximum length of
- * bytes.  For each iovec, fault in each page that constitutes the iovec.
+ * @size.  For each iovec, fault in each page that constitutes the iovec.
+ *
+ * Returns the number of bytes not faulted in (like copy_to_user() and
+ * copy_from_user()).
  *
- * Return 0 on success, or non-zero if the memory could not be accessed (i.e.
- * because it is an invalid address).
+ * Always returns 0 for non-userspace iterators.
  */
-int iov_iter_fault_in_readable(const struct iov_iter *i, size_t bytes)
+size_t fault_in_iov_iter_readable(const struct iov_iter *i, size_t size)
 {
 	if (iter_is_iovec(i)) {
+		size_t count = min(size, iov_iter_count(i));
 		const struct iovec *p;
 		size_t skip;
 
-		if (bytes > i->count)
-			bytes = i->count;
-		for (p = i->iov, skip = i->iov_offset; bytes; p++, skip = 0) {
-			size_t len = min(bytes, p->iov_len - skip);
-			int err;
+		size -= count;
+		for (p = i->iov, skip = i->iov_offset; count; p++, skip = 0) {
+			size_t len = min(count, p->iov_len - skip);
+			size_t ret;
 
 			if (unlikely(!len))
 				continue;
-			err = fault_in_pages_readable(p->iov_base + skip, len);
-			if (unlikely(err))
-				return err;
-			bytes -= len;
+			ret = fault_in_readable(p->iov_base + skip, len);
+			count -= len - ret;
+			if (ret)
+				break;
 		}
+		return count + size;
 	}
 	return 0;
 }
-EXPORT_SYMBOL(iov_iter_fault_in_readable);
+EXPORT_SYMBOL(fault_in_iov_iter_readable);
+
+/*
+ * fault_in_iov_iter_writeable - fault in iov iterator for writing
+ * @i: iterator
+ * @size: maximum length
+ *
+ * Faults in the iterator using get_user_pages(), i.e., without triggering
+ * hardware page faults.  This is primarily useful when we already know that
+ * some or all of the pages in @i aren't in memory.
+ *
+ * Returns the number of bytes not faulted in, like copy_to_user() and
+ * copy_from_user().
+ *
+ * Always returns 0 for non-user-space iterators.
+ */
+size_t fault_in_iov_iter_writeable(const struct iov_iter *i, size_t size)
+{
+	if (iter_is_iovec(i)) {
+		size_t count = min(size, iov_iter_count(i));
+		const struct iovec *p;
+		size_t skip;
+
+		size -= count;
+		for (p = i->iov, skip = i->iov_offset; count; p++, skip = 0) {
+			size_t len = min(count, p->iov_len - skip);
+			size_t ret;
+
+			if (unlikely(!len))
+				continue;
+			ret = fault_in_safe_writeable(p->iov_base + skip, len);
+			count -= len - ret;
+			if (ret)
+				break;
+		}
+		return count + size;
+	}
+	return 0;
+}
+EXPORT_SYMBOL(fault_in_iov_iter_writeable);
 
 void iov_iter_init(struct iov_iter *i, unsigned int direction,
 			const struct iovec *iov, unsigned long nr_segs,
@@ -467,6 +514,7 @@
 	WARN_ON(direction & ~(READ | WRITE));
 	*i = (struct iov_iter) {
 		.iter_type = ITER_IOVEC,
+		.nofault = false,
 		.data_source = direction,
 		.iov = iov,
 		.nr_segs = nr_segs,
@@ -532,6 +580,7 @@
 			break;
 
 		buf->ops = &default_pipe_buf_ops;
+		buf->flags = 0;
 		buf->page = page;
 		buf->offset = 0;
 		buf->len = min_t(ssize_t, left, PAGE_SIZE);
@@ -642,6 +691,7 @@
 	struct pipe_inode_info *pipe = i->pipe;
 	unsigned int p_mask = pipe->ring_size - 1;
 	unsigned int i_head;
+	unsigned int valid = pipe->head;
 	size_t n, off, xfer = 0;
 
 	if (!sanity(i))
@@ -655,11 +705,17 @@
 		rem = copy_mc_to_kernel(p + off, addr + xfer, chunk);
 		chunk -= rem;
 		kunmap_local(p);
-		i->head = i_head;
-		i->iov_offset = off + chunk;
-		xfer += chunk;
-		if (rem)
+		if (chunk) {
+			i->head = i_head;
+			i->iov_offset = off + chunk;
+			xfer += chunk;
+			valid = i_head + 1;
+		}
+		if (rem) {
+			pipe->bufs[i_head & p_mask].len -= rem;
+			pipe_discard_from(pipe, valid);
 			break;
+		}
 		n -= chunk;
 		off = 0;
 		i_head++;
@@ -1387,7 +1443,7 @@
 {
 	unsigned nr, offset;
 	pgoff_t index, count;
-	size_t size = maxsize, actual;
+	size_t size = maxsize;
 	loff_t pos;
 
 	if (!size || !maxpages)
@@ -1414,13 +1470,7 @@
 	if (nr == 0)
 		return 0;
 
-	actual = PAGE_SIZE * nr;
-	actual -= offset;
-	if (nr == count && size > 0) {
-		unsigned last_offset = (nr > 1) ? 0 : offset;
-		actual -= PAGE_SIZE - (last_offset + size);
-	}
-	return actual;
+	return min_t(size_t, nr * PAGE_SIZE - offset, maxsize);
 }
 
 /* must be done on non-empty ITER_IOVEC one */
@@ -1481,14 +1531,18 @@
 		return 0;
 
 	if (likely(iter_is_iovec(i))) {
+		unsigned int gup_flags = 0;
 		unsigned long addr;
 
+		if (iov_iter_rw(i) != WRITE)
+			gup_flags |= FOLL_WRITE;
+		if (i->nofault)
+			gup_flags |= FOLL_NOFAULT;
+
 		addr = first_iovec_segment(i, &len, start, maxsize, maxpages);
 		n = DIV_ROUND_UP(len, PAGE_SIZE);
-		res = get_user_pages_fast(addr, n,
-				iov_iter_rw(i) != WRITE ?  FOLL_WRITE : 0,
-				pages);
-		if (unlikely(res < 0))
+		res = get_user_pages_fast(addr, n, gup_flags, pages);
+		if (unlikely(res <= 0))
 			return res;
 		return (res == n ? len : res * PAGE_SIZE) - *start;
 	}
@@ -1551,7 +1605,7 @@
 	struct page **p;
 	unsigned nr, offset;
 	pgoff_t index, count;
-	size_t size = maxsize, actual;
+	size_t size = maxsize;
 	loff_t pos;
 
 	if (!size)
@@ -1580,13 +1634,7 @@
 	if (nr == 0)
 		return 0;
 
-	actual = PAGE_SIZE * nr;
-	actual -= offset;
-	if (nr == count && size > 0) {
-		unsigned last_offset = (nr > 1) ? 0 : offset;
-		actual -= PAGE_SIZE - (last_offset + size);
-	}
-	return actual;
+	return min_t(size_t, nr * PAGE_SIZE - offset, maxsize);
 }
 
 ssize_t iov_iter_get_pages_alloc(struct iov_iter *i,
@@ -1603,17 +1651,23 @@
 		return 0;
 
 	if (likely(iter_is_iovec(i))) {
+		unsigned int gup_flags = 0;
 		unsigned long addr;
 
+		if (iov_iter_rw(i) != WRITE)
+			gup_flags |= FOLL_WRITE;
+		if (i->nofault)
+			gup_flags |= FOLL_NOFAULT;
+
 		addr = first_iovec_segment(i, &len, start, maxsize, ~0U);
 		n = DIV_ROUND_UP(len, PAGE_SIZE);
 		p = get_pages_array(n);
 		if (!p)
 			return -ENOMEM;
-		res = get_user_pages_fast(addr, n,
-				iov_iter_rw(i) != WRITE ?  FOLL_WRITE : 0, p);
-		if (unlikely(res < 0)) {
+		res = get_user_pages_fast(addr, n, gup_flags, p);
+		if (unlikely(res <= 0)) {
 			kvfree(p);
+			*pages = NULL;
 			return res;
 		}
 		*pages = p;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/kobject.c
+++ linux-xilinx-zynqmp-5.15.0/lib/kobject.c
@@ -126,10 +126,10 @@
 	return 0;
 }
 
-static int get_kobj_path_length(struct kobject *kobj)
+static int get_kobj_path_length(const struct kobject *kobj)
 {
 	int length = 1;
-	struct kobject *parent = kobj;
+	const struct kobject *parent = kobj;
 
 	/* walk up the ancestors until we hit the one pointing to the
 	 * root.
@@ -144,21 +144,25 @@
 	return length;
 }
 
-static void fill_kobj_path(struct kobject *kobj, char *path, int length)
+static int fill_kobj_path(const struct kobject *kobj, char *path, int length)
 {
-	struct kobject *parent;
+	const struct kobject *parent;
 
 	--length;
 	for (parent = kobj; parent; parent = parent->parent) {
 		int cur = strlen(kobject_name(parent));
 		/* back up enough to print this name with '/' */
 		length -= cur;
+		if (length <= 0)
+			return -EINVAL;
 		memcpy(path + length, kobject_name(parent), cur);
 		*(path + --length) = '/';
 	}
 
 	pr_debug("kobject: '%s' (%p): %s: path = '%s'\n", kobject_name(kobj),
 		 kobj, __func__, path);
+
+	return 0;
 }
 
 /**
@@ -168,18 +172,22 @@
  *
  * Return: The newly allocated memory, caller must free with kfree().
  */
-char *kobject_get_path(struct kobject *kobj, gfp_t gfp_mask)
+char *kobject_get_path(const struct kobject *kobj, gfp_t gfp_mask)
 {
 	char *path;
 	int len;
 
+retry:
 	len = get_kobj_path_length(kobj);
 	if (len == 0)
 		return NULL;
 	path = kzalloc(len, gfp_mask);
 	if (!path)
 		return NULL;
-	fill_kobj_path(kobj, path, len);
+	if (fill_kobj_path(kobj, path, len)) {
+		kfree(path);
+		goto retry;
+	}
 
 	return path;
 }
@@ -874,6 +882,11 @@
 	if (!k)
 		return -EINVAL;
 
+	if (!k->kobj.ktype) {
+		pr_err("must have a ktype to be initialized properly!\n");
+		return -EINVAL;
+	}
+
 	kset_init(k);
 	err = kobject_add_internal(&k->kobj);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/kobject_uevent.c
+++ linux-xilinx-zynqmp-5.15.0/lib/kobject_uevent.c
@@ -432,8 +432,23 @@
 		len = strlen(env->envp[i]) + 1;
 
 		if (i != env->envp_idx - 1) {
+			/* @env->envp[] contains pointers to @env->buf[]
+			 * with @env->buflen chars, and we are removing
+			 * variable MODALIAS here pointed by @env->envp[i]
+			 * with length @len as shown below:
+			 *
+			 * 0               @env->buf[]      @env->buflen
+			 * ---------------------------------------------
+			 * ^             ^              ^              ^
+			 * |             |->   @len   <-| target block |
+			 * @env->envp[0] @env->envp[i]  @env->envp[i + 1]
+			 *
+			 * so the "target block" indicated above is moved
+			 * backward by @len, and its right size is
+			 * @env->buflen - (@env->envp[i + 1] - @env->envp[0]).
+			 */
 			memmove(env->envp[i], env->envp[i + 1],
-				env->buflen - len);
+				env->buflen - (env->envp[i + 1] - env->envp[0]));
 
 			for (j = i; j < env->envp_idx - 1; j++)
 				env->envp[j] = env->envp[j + 1] - len;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/kunit/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/lib/kunit/debugfs.c
@@ -52,12 +52,14 @@
 static int debugfs_print_results(struct seq_file *seq, void *v)
 {
 	struct kunit_suite *suite = (struct kunit_suite *)seq->private;
-	bool success = kunit_suite_has_succeeded(suite);
+	enum kunit_status success;
 	struct kunit_case *test_case;
 
 	if (!suite || !suite->log)
 		return 0;
 
+	success = kunit_suite_has_succeeded(suite);
+
 	seq_printf(seq, "%s", suite->log);
 
 	kunit_suite_for_each_test_case(suite, test_case)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/kunit/test.c
+++ linux-xilinx-zynqmp-5.15.0/lib/kunit/test.c
@@ -504,16 +504,18 @@
 		struct kunit_result_stats param_stats = { 0 };
 		test_case->status = KUNIT_SKIPPED;
 
-		if (test_case->generate_params) {
+		if (!test_case->generate_params) {
+			/* Non-parameterised test. */
+			kunit_run_case_catch_errors(suite, test_case, &test);
+			kunit_update_stats(&param_stats, test.status);
+		} else {
 			/* Get initial param. */
 			param_desc[0] = '\0';
 			test.param_value = test_case->generate_params(NULL, param_desc);
-		}
 
-		do {
-			kunit_run_case_catch_errors(suite, test_case, &test);
+			while (test.param_value) {
+				kunit_run_case_catch_errors(suite, test_case, &test);
 
-			if (test_case->generate_params) {
 				if (param_desc[0] == '\0') {
 					snprintf(param_desc, sizeof(param_desc),
 						 "param-%d", test.param_index);
@@ -530,11 +532,11 @@
 				param_desc[0] = '\0';
 				test.param_value = test_case->generate_params(test.param_value, param_desc);
 				test.param_index++;
-			}
 
-			kunit_update_stats(&param_stats, test.status);
+				kunit_update_stats(&param_stats, test.status);
+			}
+		}
 
-		} while (test.param_value);
 
 		kunit_print_test_stats(&test, param_stats);
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/kunit/try-catch.c
+++ linux-xilinx-zynqmp-5.15.0/lib/kunit/try-catch.c
@@ -52,7 +52,7 @@
 	 * If tests timeout due to exceeding sysctl_hung_task_timeout_secs,
 	 * the task will be killed and an oops generated.
 	 */
-	return 300 * MSEC_PER_SEC; /* 5 min */
+	return 300 * msecs_to_jiffies(MSEC_PER_SEC); /* 5 min */
 }
 
 void kunit_try_catch_run(struct kunit_try_catch *try_catch, void *context)
@@ -76,7 +76,6 @@
 	time_remaining = wait_for_completion_timeout(&try_completion,
 						     kunit_test_timeout());
 	if (time_remaining == 0) {
-		kunit_err(test, "try timed out\n");
 		try_catch->try_result = -ETIMEDOUT;
 	}
 
@@ -89,6 +88,8 @@
 		try_catch->try_result = 0;
 	else if (exit_code == -EINTR)
 		kunit_err(test, "wake_up_process() was never called\n");
+	else if (exit_code == -ETIMEDOUT)
+		kunit_err(test, "try timed out\n");
 	else if (exit_code)
 		kunit_err(test, "Unknown error: %d\n", exit_code);
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/list-test.c
+++ linux-xilinx-zynqmp-5.15.0/lib/list-test.c
@@ -234,6 +234,24 @@
 	KUNIT_EXPECT_EQ(test, i, 2);
 }
 
+static void list_test_list_is_head(struct kunit *test)
+{
+	struct list_head a, b, c;
+
+	/* Two lists: [a] -> b, [c] */
+	INIT_LIST_HEAD(&a);
+	INIT_LIST_HEAD(&c);
+	list_add_tail(&b, &a);
+
+	KUNIT_EXPECT_TRUE_MSG(test, list_is_head(&a, &a),
+		"Head element of same list");
+	KUNIT_EXPECT_FALSE_MSG(test, list_is_head(&a, &b),
+		"Non-head element of same list");
+	KUNIT_EXPECT_FALSE_MSG(test, list_is_head(&a, &c),
+		"Head element of different list");
+}
+
+
 static void list_test_list_is_first(struct kunit *test)
 {
 	struct list_head a, b;
@@ -710,6 +728,7 @@
 	KUNIT_CASE(list_test_list_move),
 	KUNIT_CASE(list_test_list_move_tail),
 	KUNIT_CASE(list_test_list_bulk_move_tail),
+	KUNIT_CASE(list_test_list_is_head),
 	KUNIT_CASE(list_test_list_is_first),
 	KUNIT_CASE(list_test_list_is_last),
 	KUNIT_CASE(list_test_list_empty),
--- linux-xilinx-zynqmp-5.15.0.orig/lib/list_debug.c
+++ linux-xilinx-zynqmp-5.15.0/lib/list_debug.c
@@ -20,7 +20,11 @@
 bool __list_add_valid(struct list_head *new, struct list_head *prev,
 		      struct list_head *next)
 {
-	if (CHECK_DATA_CORRUPTION(next->prev != prev,
+	if (CHECK_DATA_CORRUPTION(prev == NULL,
+			"list_add corruption. prev is NULL.\n") ||
+	    CHECK_DATA_CORRUPTION(next == NULL,
+			"list_add corruption. next is NULL.\n") ||
+	    CHECK_DATA_CORRUPTION(next->prev != prev,
 			"list_add corruption. next->prev should be prev (%px), but was %px. (next=%px).\n",
 			prev, next->prev, next) ||
 	    CHECK_DATA_CORRUPTION(prev->next != next,
@@ -42,7 +46,11 @@
 	prev = entry->prev;
 	next = entry->next;
 
-	if (CHECK_DATA_CORRUPTION(next == LIST_POISON1,
+	if (CHECK_DATA_CORRUPTION(next == NULL,
+			"list_del corruption, %px->next is NULL\n", entry) ||
+	    CHECK_DATA_CORRUPTION(prev == NULL,
+			"list_del corruption, %px->prev is NULL\n", entry) ||
+	    CHECK_DATA_CORRUPTION(next == LIST_POISON1,
 			"list_del corruption, %px->next is LIST_POISON1 (%px)\n",
 			entry, LIST_POISON1) ||
 	    CHECK_DATA_CORRUPTION(prev == LIST_POISON2,
--- linux-xilinx-zynqmp-5.15.0.orig/lib/livepatch/test_klp_callbacks_busy.c
+++ linux-xilinx-zynqmp-5.15.0/lib/livepatch/test_klp_callbacks_busy.c
@@ -16,10 +16,12 @@
 
 static void busymod_work_func(struct work_struct *work);
 static DECLARE_WORK(work, busymod_work_func);
+static DECLARE_COMPLETION(busymod_work_started);
 
 static void busymod_work_func(struct work_struct *work)
 {
 	pr_info("%s enter\n", __func__);
+	complete(&busymod_work_started);
 
 	while (READ_ONCE(block_transition)) {
 		/*
@@ -37,6 +39,12 @@
 	pr_info("%s\n", __func__);
 	schedule_work(&work);
 
+	/*
+	 * To synchronize kernel messages, hold the init function from
+	 * exiting until the work function's entry message has printed.
+	 */
+	wait_for_completion(&busymod_work_started);
+
 	if (!block_transition) {
 		/*
 		 * Serialize output: print all messages from the work
--- linux-xilinx-zynqmp-5.15.0.orig/lib/lockref.c
+++ linux-xilinx-zynqmp-5.15.0/lib/lockref.c
@@ -24,7 +24,6 @@
 		}								\
 		if (!--retry)							\
 			break;							\
-		cpu_relax();							\
 	}									\
 } while (0)
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/logic_iomem.c
+++ linux-xilinx-zynqmp-5.15.0/lib/logic_iomem.c
@@ -21,15 +21,15 @@
 
 #define AREA_SHIFT	24
 #define MAX_AREA_SIZE	(1 << AREA_SHIFT)
-#define MAX_AREAS	((1ULL<<32) / MAX_AREA_SIZE)
+#define MAX_AREAS	((1U << 31) / MAX_AREA_SIZE)
 #define AREA_BITS	((MAX_AREAS - 1) << AREA_SHIFT)
 #define AREA_MASK	(MAX_AREA_SIZE - 1)
 #ifdef CONFIG_64BIT
 #define IOREMAP_BIAS	0xDEAD000000000000UL
 #define IOREMAP_MASK	0xFFFFFFFF00000000UL
 #else
-#define IOREMAP_BIAS	0
-#define IOREMAP_MASK	0
+#define IOREMAP_BIAS	0x80000000UL
+#define IOREMAP_MASK	0x80000000UL
 #endif
 
 static DEFINE_MUTEX(regions_mtx);
@@ -68,7 +68,7 @@
 }
 EXPORT_SYMBOL(logic_iomem_add_region);
 
-#ifndef CONFIG_LOGIC_IOMEM_FALLBACK
+#ifndef CONFIG_INDIRECT_IOMEM_FALLBACK
 static void __iomem *real_ioremap(phys_addr_t offset, size_t size)
 {
 	WARN(1, "invalid ioremap(0x%llx, 0x%zx)\n",
@@ -79,9 +79,9 @@
 static void real_iounmap(void __iomem *addr)
 {
 	WARN(1, "invalid iounmap for addr 0x%llx\n",
-	     (unsigned long long __force)addr);
+	     (unsigned long long)(uintptr_t __force)addr);
 }
-#endif /* CONFIG_LOGIC_IOMEM_FALLBACK */
+#endif /* CONFIG_INDIRECT_IOMEM_FALLBACK */
 
 void __iomem *ioremap(phys_addr_t offset, size_t size)
 {
@@ -168,12 +168,12 @@
 }
 EXPORT_SYMBOL(iounmap);
 
-#ifndef CONFIG_LOGIC_IOMEM_FALLBACK
+#ifndef CONFIG_INDIRECT_IOMEM_FALLBACK
 #define MAKE_FALLBACK(op, sz) 						\
 static u##sz real_raw_read ## op(const volatile void __iomem *addr)	\
 {									\
 	WARN(1, "Invalid read" #op " at address %llx\n",		\
-	     (unsigned long long __force)addr);				\
+	     (unsigned long long)(uintptr_t __force)addr);		\
 	return (u ## sz)~0ULL;						\
 }									\
 									\
@@ -181,7 +181,8 @@
 				 volatile void __iomem *addr)		\
 {									\
 	WARN(1, "Invalid writeq" #op " of 0x%llx at address %llx\n",	\
-	     (unsigned long long)val, (unsigned long long __force)addr);\
+	     (unsigned long long)val,					\
+	     (unsigned long long)(uintptr_t __force)addr);\
 }									\
 
 MAKE_FALLBACK(b, 8);
@@ -194,14 +195,14 @@
 static void real_memset_io(volatile void __iomem *addr, int value, size_t size)
 {
 	WARN(1, "Invalid memset_io at address 0x%llx\n",
-	     (unsigned long long __force)addr);
+	     (unsigned long long)(uintptr_t __force)addr);
 }
 
 static void real_memcpy_fromio(void *buffer, const volatile void __iomem *addr,
 			       size_t size)
 {
 	WARN(1, "Invalid memcpy_fromio at address 0x%llx\n",
-	     (unsigned long long __force)addr);
+	     (unsigned long long)(uintptr_t __force)addr);
 
 	memset(buffer, 0xff, size);
 }
@@ -210,9 +211,9 @@
 			     size_t size)
 {
 	WARN(1, "Invalid memcpy_toio at address 0x%llx\n",
-	     (unsigned long long __force)addr);
+	     (unsigned long long)(uintptr_t __force)addr);
 }
-#endif /* CONFIG_LOGIC_IOMEM_FALLBACK */
+#endif /* CONFIG_INDIRECT_IOMEM_FALLBACK */
 
 #define MAKE_OP(op, sz) 						\
 u##sz __raw_read ## op(const volatile void __iomem *addr)		\
--- linux-xilinx-zynqmp-5.15.0.orig/lib/lz4/lz4_decompress.c
+++ linux-xilinx-zynqmp-5.15.0/lib/lz4/lz4_decompress.c
@@ -271,8 +271,12 @@
 			ip += length;
 			op += length;
 
-			/* Necessarily EOF, due to parsing restrictions */
-			if (!partialDecoding || (cpy == oend))
+			/* Necessarily EOF when !partialDecoding.
+			 * When partialDecoding, it is EOF if we've either
+			 * filled the output buffer or
+			 * can't proceed with reading an offset for following match.
+			 */
+			if (!partialDecoding || (cpy == oend) || (ip >= (iend - 2)))
 				break;
 		} else {
 			/* may overwrite up to WILDCOPYLENGTH beyond cpy */
--- linux-xilinx-zynqmp-5.15.0.orig/lib/math/prime_numbers.c
+++ linux-xilinx-zynqmp-5.15.0/lib/math/prime_numbers.c
@@ -6,8 +6,6 @@
 #include <linux/prime_numbers.h>
 #include <linux/slab.h>
 
-#define bitmap_size(nbits) (BITS_TO_LONGS(nbits) * sizeof(unsigned long))
-
 struct primes {
 	struct rcu_head rcu;
 	unsigned long last, sz;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/memneq.c
+++ linux-xilinx-zynqmp-5.15.0/lib/memneq.c
@@ -0,0 +1,168 @@
+/*
+ * Constant-time equality testing of memory regions.
+ *
+ * Authors:
+ *
+ *   James Yonan <james@openvpn.net>
+ *   Daniel Borkmann <dborkman@redhat.com>
+ *
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright(c) 2013 OpenVPN Technologies, Inc. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ * The full GNU General Public License is included in this distribution
+ * in the file called LICENSE.GPL.
+ *
+ * BSD LICENSE
+ *
+ * Copyright(c) 2013 OpenVPN Technologies, Inc. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *   * Redistributions of source code must retain the above copyright
+ *     notice, this list of conditions and the following disclaimer.
+ *   * Redistributions in binary form must reproduce the above copyright
+ *     notice, this list of conditions and the following disclaimer in
+ *     the documentation and/or other materials provided with the
+ *     distribution.
+ *   * Neither the name of OpenVPN Technologies nor the names of its
+ *     contributors may be used to endorse or promote products derived
+ *     from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <crypto/algapi.h>
+
+#ifndef __HAVE_ARCH_CRYPTO_MEMNEQ
+
+/* Generic path for arbitrary size */
+static inline unsigned long
+__crypto_memneq_generic(const void *a, const void *b, size_t size)
+{
+	unsigned long neq = 0;
+
+#if defined(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS)
+	while (size >= sizeof(unsigned long)) {
+		neq |= *(unsigned long *)a ^ *(unsigned long *)b;
+		OPTIMIZER_HIDE_VAR(neq);
+		a += sizeof(unsigned long);
+		b += sizeof(unsigned long);
+		size -= sizeof(unsigned long);
+	}
+#endif /* CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS */
+	while (size > 0) {
+		neq |= *(unsigned char *)a ^ *(unsigned char *)b;
+		OPTIMIZER_HIDE_VAR(neq);
+		a += 1;
+		b += 1;
+		size -= 1;
+	}
+	return neq;
+}
+
+/* Loop-free fast-path for frequently used 16-byte size */
+static inline unsigned long __crypto_memneq_16(const void *a, const void *b)
+{
+	unsigned long neq = 0;
+
+#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+	if (sizeof(unsigned long) == 8) {
+		neq |= *(unsigned long *)(a)   ^ *(unsigned long *)(b);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned long *)(a+8) ^ *(unsigned long *)(b+8);
+		OPTIMIZER_HIDE_VAR(neq);
+	} else if (sizeof(unsigned int) == 4) {
+		neq |= *(unsigned int *)(a)    ^ *(unsigned int *)(b);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned int *)(a+4)  ^ *(unsigned int *)(b+4);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned int *)(a+8)  ^ *(unsigned int *)(b+8);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned int *)(a+12) ^ *(unsigned int *)(b+12);
+		OPTIMIZER_HIDE_VAR(neq);
+	} else
+#endif /* CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS */
+	{
+		neq |= *(unsigned char *)(a)    ^ *(unsigned char *)(b);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+1)  ^ *(unsigned char *)(b+1);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+2)  ^ *(unsigned char *)(b+2);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+3)  ^ *(unsigned char *)(b+3);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+4)  ^ *(unsigned char *)(b+4);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+5)  ^ *(unsigned char *)(b+5);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+6)  ^ *(unsigned char *)(b+6);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+7)  ^ *(unsigned char *)(b+7);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+8)  ^ *(unsigned char *)(b+8);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+9)  ^ *(unsigned char *)(b+9);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+10) ^ *(unsigned char *)(b+10);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+11) ^ *(unsigned char *)(b+11);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+12) ^ *(unsigned char *)(b+12);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+13) ^ *(unsigned char *)(b+13);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+14) ^ *(unsigned char *)(b+14);
+		OPTIMIZER_HIDE_VAR(neq);
+		neq |= *(unsigned char *)(a+15) ^ *(unsigned char *)(b+15);
+		OPTIMIZER_HIDE_VAR(neq);
+	}
+
+	return neq;
+}
+
+/* Compare two areas of memory without leaking timing information,
+ * and with special optimizations for common sizes.  Users should
+ * not call this function directly, but should instead use
+ * crypto_memneq defined in crypto/algapi.h.
+ */
+noinline unsigned long __crypto_memneq(const void *a, const void *b,
+				       size_t size)
+{
+	switch (size) {
+	case 16:
+		return __crypto_memneq_16(a, b);
+	default:
+		return __crypto_memneq_generic(a, b, size);
+	}
+}
+EXPORT_SYMBOL(__crypto_memneq);
+
+#endif /* __HAVE_ARCH_CRYPTO_MEMNEQ */
--- linux-xilinx-zynqmp-5.15.0.orig/lib/mpi/ec.c
+++ linux-xilinx-zynqmp-5.15.0/lib/mpi/ec.c
@@ -584,6 +584,9 @@
 	ctx->a = mpi_copy(a);
 	ctx->b = mpi_copy(b);
 
+	ctx->d = NULL;
+	ctx->t.two_inv_p = NULL;
+
 	ctx->t.p_barrett = use_barrett > 0 ? mpi_barrett_init(ctx->p, 0) : NULL;
 
 	mpi_ec_get_reset(ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/mpi/mpi-cmp.c
+++ linux-xilinx-zynqmp-5.15.0/lib/mpi/mpi-cmp.c
@@ -25,8 +25,12 @@
 	mpi_limb_t limb = v;
 
 	mpi_normalize(u);
-	if (!u->nlimbs && !limb)
-		return 0;
+	if (u->nlimbs == 0) {
+		if (v == 0)
+			return 0;
+		else
+			return -1;
+	}
 	if (u->sign)
 		return -1;
 	if (u->nlimbs > 1)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/mpi/mpi-mod.c
+++ linux-xilinx-zynqmp-5.15.0/lib/mpi/mpi-mod.c
@@ -40,6 +40,8 @@
 
 	mpi_normalize(m);
 	ctx = kcalloc(1, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return NULL;
 
 	if (copy) {
 		ctx->m = mpi_copy(m);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/mpi/mpicoder.c
+++ linux-xilinx-zynqmp-5.15.0/lib/mpi/mpicoder.c
@@ -504,7 +504,8 @@
 
 	while (sg_miter_next(&miter)) {
 		buff = miter.addr;
-		len = miter.length;
+		len = min_t(unsigned, miter.length, nbytes);
+		nbytes -= len;
 
 		for (x = 0; x < len; x++) {
 			a <<= 8;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/nlattr.c
+++ linux-xilinx-zynqmp-5.15.0/lib/nlattr.c
@@ -10,6 +10,7 @@
 #include <linux/kernel.h>
 #include <linux/errno.h>
 #include <linux/jiffies.h>
+#include <linux/nospec.h>
 #include <linux/skbuff.h>
 #include <linux/string.h>
 #include <linux/types.h>
@@ -369,6 +370,7 @@
 	if (type <= 0 || type > maxtype)
 		return 0;
 
+	type = array_index_nospec(type, maxtype + 1);
 	pt = &policy[type];
 
 	BUG_ON(pt->type > NLA_TYPE_MAX);
@@ -584,6 +586,7 @@
 			}
 			continue;
 		}
+		type = array_index_nospec(type, maxtype + 1);
 		if (policy) {
 			int err = validate_nla(nla, maxtype, policy,
 					       validate, extack, depth);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/nmi_backtrace.c
+++ linux-xilinx-zynqmp-5.15.0/lib/nmi_backtrace.c
@@ -75,6 +75,12 @@
 		touch_softlockup_watchdog();
 	}
 
+	/*
+	 * Force flush any remote buffers that might be stuck in IRQ context
+	 * and therefore could not run their irq_work.
+	 */
+	printk_trigger_flush();
+
 	clear_bit_unlock(0, &backtrace_flag);
 	put_cpu();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/lib/nodemask.c
+++ linux-xilinx-zynqmp-5.15.0/lib/nodemask.c
@@ -3,9 +3,9 @@
 #include <linux/module.h>
 #include <linux/random.h>
 
-int __next_node_in(int node, const nodemask_t *srcp)
+unsigned int __next_node_in(int node, const nodemask_t *srcp)
 {
-	int ret = __next_node(node, srcp);
+	unsigned int ret = __next_node(node, srcp);
 
 	if (ret == MAX_NUMNODES)
 		ret = __first_node(srcp);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/notifier-error-inject.c
+++ linux-xilinx-zynqmp-5.15.0/lib/notifier-error-inject.c
@@ -15,7 +15,7 @@
 	return 0;
 }
 
-DEFINE_SIMPLE_ATTRIBUTE(fops_errno, debugfs_errno_get, debugfs_errno_set,
+DEFINE_SIMPLE_ATTRIBUTE_SIGNED(fops_errno, debugfs_errno_get, debugfs_errno_set,
 			"%lld\n");
 
 static struct dentry *debugfs_create_errno(const char *name, umode_t mode,
--- linux-xilinx-zynqmp-5.15.0.orig/lib/objagg.c
+++ linux-xilinx-zynqmp-5.15.0/lib/objagg.c
@@ -167,6 +167,9 @@
 {
 	void *delta_priv;
 
+	if (WARN_ON(!objagg_obj_is_root(parent)))
+		return -EINVAL;
+
 	delta_priv = objagg->ops->delta_create(objagg->priv, parent->obj,
 					       objagg_obj->obj);
 	if (IS_ERR(delta_priv))
@@ -906,20 +909,6 @@
 	[OBJAGG_OPT_ALGO_SIMPLE_GREEDY] = &objagg_opt_simple_greedy,
 };
 
-static int objagg_hints_obj_cmp(struct rhashtable_compare_arg *arg,
-				const void *obj)
-{
-	struct rhashtable *ht = arg->ht;
-	struct objagg_hints *objagg_hints =
-			container_of(ht, struct objagg_hints, node_ht);
-	const struct objagg_ops *ops = objagg_hints->ops;
-	const char *ptr = obj;
-
-	ptr += ht->p.key_offset;
-	return ops->hints_obj_cmp ? ops->hints_obj_cmp(ptr, arg->key) :
-				    memcmp(ptr, arg->key, ht->p.key_len);
-}
-
 /**
  * objagg_hints_get - obtains hints instance
  * @objagg:		objagg instance
@@ -958,7 +947,6 @@
 				offsetof(struct objagg_hints_node, obj);
 	objagg_hints->ht_params.head_offset =
 				offsetof(struct objagg_hints_node, ht_node);
-	objagg_hints->ht_params.obj_cmpfn = objagg_hints_obj_cmp;
 
 	err = rhashtable_init(&objagg_hints->node_ht, &objagg_hints->ht_params);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/once.c
+++ linux-xilinx-zynqmp-5.15.0/lib/once.c
@@ -66,3 +66,33 @@
 	once_disable_jump(once_key, mod);
 }
 EXPORT_SYMBOL(__do_once_done);
+
+static DEFINE_MUTEX(once_mutex);
+
+bool __do_once_slow_start(bool *done)
+	__acquires(once_mutex)
+{
+	mutex_lock(&once_mutex);
+	if (*done) {
+		mutex_unlock(&once_mutex);
+		/* Keep sparse happy by restoring an even lock count on
+		 * this mutex. In case we return here, we don't call into
+		 * __do_once_done but return early in the DO_ONCE_SLOW() macro.
+		 */
+		__acquire(once_mutex);
+		return false;
+	}
+
+	return true;
+}
+EXPORT_SYMBOL(__do_once_slow_start);
+
+void __do_once_slow_done(bool *done, struct static_key_true *once_key,
+			 struct module *mod)
+	__releases(once_mutex)
+{
+	*done = true;
+	mutex_unlock(&once_mutex);
+	once_disable_jump(once_key, mod);
+}
+EXPORT_SYMBOL(__do_once_slow_done);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/pci_iomap.c
+++ linux-xilinx-zynqmp-5.15.0/lib/pci_iomap.c
@@ -170,8 +170,8 @@
 
 	if (addr >= start && addr < start + IO_SPACE_LIMIT)
 		return;
-	iounmap(p);
 #endif
+	iounmap(p);
 }
 EXPORT_SYMBOL(pci_iounmap);
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/percpu-refcount.c
+++ linux-xilinx-zynqmp-5.15.0/lib/percpu-refcount.c
@@ -76,6 +76,7 @@
 	data = kzalloc(sizeof(*ref->data), gfp);
 	if (!data) {
 		free_percpu((void __percpu *)ref->percpu_count_ptr);
+		ref->percpu_count_ptr = 0;
 		return -ENOMEM;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/radix-tree.c
+++ linux-xilinx-zynqmp-5.15.0/lib/radix-tree.c
@@ -27,6 +27,7 @@
 #include <linux/string.h>
 #include <linux/xarray.h>
 
+
 /*
  * Radix tree node cache.
  */
@@ -57,10 +58,12 @@
 /*
  * Per-cpu pool of preloaded nodes
  */
-DEFINE_PER_CPU(struct radix_tree_preload, radix_tree_preloads) = {
-	.lock = INIT_LOCAL_LOCK(lock),
+struct radix_tree_preload {
+	unsigned nr;
+	/* nodes->parent points to next preallocated node */
+	struct radix_tree_node *nodes;
 };
-EXPORT_PER_CPU_SYMBOL_GPL(radix_tree_preloads);
+static DEFINE_PER_CPU(struct radix_tree_preload, radix_tree_preloads) = { 0, };
 
 static inline struct radix_tree_node *entry_to_node(void *ptr)
 {
@@ -329,14 +332,14 @@
 	 */
 	gfp_mask &= ~__GFP_ACCOUNT;
 
-	local_lock(&radix_tree_preloads.lock);
+	preempt_disable();
 	rtp = this_cpu_ptr(&radix_tree_preloads);
 	while (rtp->nr < nr) {
-		local_unlock(&radix_tree_preloads.lock);
+		preempt_enable();
 		node = kmem_cache_alloc(radix_tree_node_cachep, gfp_mask);
 		if (node == NULL)
 			goto out;
-		local_lock(&radix_tree_preloads.lock);
+		preempt_disable();
 		rtp = this_cpu_ptr(&radix_tree_preloads);
 		if (rtp->nr < nr) {
 			node->parent = rtp->nodes;
@@ -378,7 +381,7 @@
 	if (gfpflags_allow_blocking(gfp_mask))
 		return __radix_tree_preload(gfp_mask, RADIX_TREE_PRELOAD_SIZE);
 	/* Preloading doesn't help anything with this gfp mask, skip it */
-	local_lock(&radix_tree_preloads.lock);
+	preempt_disable();
 	return 0;
 }
 EXPORT_SYMBOL(radix_tree_maybe_preload);
@@ -1134,7 +1137,6 @@
 void __rcu **radix_tree_iter_resume(void __rcu **slot,
 					struct radix_tree_iter *iter)
 {
-	slot++;
 	iter->index = __radix_tree_iter_add(iter, 1);
 	iter->next_index = iter->index;
 	iter->tags = 0;
@@ -1468,7 +1470,7 @@
 void idr_preload(gfp_t gfp_mask)
 {
 	if (__radix_tree_preload(gfp_mask, IDR_PRELOAD_SIZE))
-		local_lock(&radix_tree_preloads.lock);
+		preempt_disable();
 }
 EXPORT_SYMBOL(idr_preload);
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/raid6/test/Makefile
+++ linux-xilinx-zynqmp-5.15.0/lib/raid6/test/Makefile
@@ -4,6 +4,8 @@
 # from userspace.
 #
 
+pound := \#
+
 CC	 = gcc
 OPTFLAGS = -O2			# Adjust as desired
 CFLAGS	 = -I.. -I ../../../include -g $(OPTFLAGS)
@@ -42,7 +44,7 @@
         OBJS   += neon.o neon1.o neon2.o neon4.o neon8.o recov_neon.o recov_neon_inner.o
         CFLAGS += -DCONFIG_KERNEL_MODE_NEON=1
 else
-        HAS_ALTIVEC := $(shell printf '\#include <altivec.h>\nvector int a;\n' |\
+        HAS_ALTIVEC := $(shell printf '$(pound)include <altivec.h>\nvector int a;\n' |\
                          gcc -c -x c - >/dev/null && rm ./-.o && echo yes)
         ifeq ($(HAS_ALTIVEC),yes)
                 CFLAGS += -I../../../arch/powerpc/include
--- linux-xilinx-zynqmp-5.15.0.orig/lib/raid6/test/test.c
+++ linux-xilinx-zynqmp-5.15.0/lib/raid6/test/test.c
@@ -19,7 +19,6 @@
 #define NDISKS		16	/* Including P and Q */
 
 const char raid6_empty_zero_page[PAGE_SIZE] __attribute__((aligned(PAGE_SIZE)));
-struct raid6_calls raid6_call;
 
 char *dataptrs[NDISKS];
 char data[NDISKS][PAGE_SIZE] __attribute__((aligned(PAGE_SIZE)));
--- linux-xilinx-zynqmp-5.15.0.orig/lib/random32.c
+++ linux-xilinx-zynqmp-5.15.0/lib/random32.c
@@ -39,8 +39,9 @@
 #include <linux/random.h>
 #include <linux/sched.h>
 #include <linux/bitops.h>
+#include <linux/slab.h>
+#include <linux/notifier.h>
 #include <asm/unaligned.h>
-#include <trace/events/random.h>
 
 /**
  *	prandom_u32_state - seeded pseudo-random number generator.
@@ -386,7 +387,6 @@
 	struct siprand_state *state = get_cpu_ptr(&net_rand_state);
 	u32 res = siprand_u32(state);
 
-	trace_prandom_u32(res);
 	put_cpu_ptr(&net_rand_state);
 	return res;
 }
@@ -552,9 +552,11 @@
  * To avoid worrying about whether it's safe to delay that interrupt
  * long enough to seed all CPUs, just schedule an immediate timer event.
  */
-static void prandom_timer_start(struct random_ready_callback *unused)
+static int prandom_timer_start(struct notifier_block *nb,
+			       unsigned long action, void *data)
 {
 	mod_timer(&seed_timer, jiffies);
+	return 0;
 }
 
 #ifdef CONFIG_RANDOM32_SELFTEST
@@ -618,13 +620,13 @@
  */
 static int __init prandom_init_late(void)
 {
-	static struct random_ready_callback random_ready = {
-		.func = prandom_timer_start
+	static struct notifier_block random_ready = {
+		.notifier_call = prandom_timer_start
 	};
-	int ret = add_random_ready_callback(&random_ready);
+	int ret = register_random_ready_notifier(&random_ready);
 
 	if (ret == -EALREADY) {
-		prandom_timer_start(&random_ready);
+		prandom_timer_start(&random_ready, 0, NULL);
 		ret = 0;
 	}
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/ratelimit.c
+++ linux-xilinx-zynqmp-5.15.0/lib/ratelimit.c
@@ -26,10 +26,16 @@
  */
 int ___ratelimit(struct ratelimit_state *rs, const char *func)
 {
+	/* Paired with WRITE_ONCE() in .proc_handler().
+	 * Changing two values seperately could be inconsistent
+	 * and some message could be lost.  (See: net_ratelimit_state).
+	 */
+	int interval = READ_ONCE(rs->interval);
+	int burst = READ_ONCE(rs->burst);
 	unsigned long flags;
 	int ret;
 
-	if (!rs->interval)
+	if (!interval)
 		return 1;
 
 	/*
@@ -44,7 +50,7 @@
 	if (!rs->begin)
 		rs->begin = jiffies;
 
-	if (time_is_before_jiffies(rs->begin + rs->interval)) {
+	if (time_is_before_jiffies(rs->begin + interval)) {
 		if (rs->missed) {
 			if (!(rs->flags & RATELIMIT_MSG_ON_RELEASE)) {
 				printk_deferred(KERN_WARNING
@@ -56,7 +62,7 @@
 		rs->begin   = jiffies;
 		rs->printed = 0;
 	}
-	if (rs->burst && rs->burst > rs->printed) {
+	if (burst && burst > rs->printed) {
 		rs->printed++;
 		ret = 1;
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/lib/ref_tracker.c
+++ linux-xilinx-zynqmp-5.15.0/lib/ref_tracker.c
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+#include <linux/export.h>
+#include <linux/ref_tracker.h>
+#include <linux/slab.h>
+#include <linux/stacktrace.h>
+#include <linux/stackdepot.h>
+
+#define REF_TRACKER_STACK_ENTRIES 16
+
+struct ref_tracker {
+	struct list_head	head;   /* anchor into dir->list or dir->quarantine */
+	bool			dead;
+	depot_stack_handle_t	alloc_stack_handle;
+	depot_stack_handle_t	free_stack_handle;
+};
+
+void ref_tracker_dir_exit(struct ref_tracker_dir *dir)
+{
+	struct ref_tracker *tracker, *n;
+	unsigned long flags;
+	bool leak = false;
+
+	spin_lock_irqsave(&dir->lock, flags);
+	list_for_each_entry_safe(tracker, n, &dir->quarantine, head) {
+		list_del(&tracker->head);
+		kfree(tracker);
+		dir->quarantine_avail++;
+	}
+	list_for_each_entry_safe(tracker, n, &dir->list, head) {
+		pr_err("leaked reference.\n");
+		if (tracker->alloc_stack_handle)
+			stack_depot_print(tracker->alloc_stack_handle);
+		leak = true;
+		list_del(&tracker->head);
+		kfree(tracker);
+	}
+	spin_unlock_irqrestore(&dir->lock, flags);
+	WARN_ON_ONCE(leak);
+	WARN_ON_ONCE(refcount_read(&dir->untracked) != 1);
+}
+EXPORT_SYMBOL(ref_tracker_dir_exit);
+
+void ref_tracker_dir_print(struct ref_tracker_dir *dir,
+			   unsigned int display_limit)
+{
+	struct ref_tracker *tracker;
+	unsigned long flags;
+	unsigned int i = 0;
+
+	spin_lock_irqsave(&dir->lock, flags);
+	list_for_each_entry(tracker, &dir->list, head) {
+		if (i < display_limit) {
+			pr_err("leaked reference.\n");
+			if (tracker->alloc_stack_handle)
+				stack_depot_print(tracker->alloc_stack_handle);
+			i++;
+		} else {
+			break;
+		}
+	}
+	spin_unlock_irqrestore(&dir->lock, flags);
+}
+EXPORT_SYMBOL(ref_tracker_dir_print);
+
+int ref_tracker_alloc(struct ref_tracker_dir *dir,
+		      struct ref_tracker **trackerp,
+		      gfp_t gfp)
+{
+	unsigned long entries[REF_TRACKER_STACK_ENTRIES];
+	struct ref_tracker *tracker;
+	unsigned int nr_entries;
+	unsigned long flags;
+
+	*trackerp = tracker = kzalloc(sizeof(*tracker), gfp | __GFP_NOFAIL);
+	if (unlikely(!tracker)) {
+		pr_err_once("memory allocation failure, unreliable refcount tracker.\n");
+		refcount_inc(&dir->untracked);
+		return -ENOMEM;
+	}
+	nr_entries = stack_trace_save(entries, ARRAY_SIZE(entries), 1);
+	nr_entries = filter_irq_stacks(entries, nr_entries);
+	tracker->alloc_stack_handle = stack_depot_save(entries, nr_entries, gfp);
+
+	spin_lock_irqsave(&dir->lock, flags);
+	list_add(&tracker->head, &dir->list);
+	spin_unlock_irqrestore(&dir->lock, flags);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ref_tracker_alloc);
+
+int ref_tracker_free(struct ref_tracker_dir *dir,
+		     struct ref_tracker **trackerp)
+{
+	unsigned long entries[REF_TRACKER_STACK_ENTRIES];
+	struct ref_tracker *tracker = *trackerp;
+	depot_stack_handle_t stack_handle;
+	unsigned int nr_entries;
+	unsigned long flags;
+
+	if (!tracker) {
+		refcount_dec(&dir->untracked);
+		return -EEXIST;
+	}
+	nr_entries = stack_trace_save(entries, ARRAY_SIZE(entries), 1);
+	nr_entries = filter_irq_stacks(entries, nr_entries);
+	stack_handle = stack_depot_save(entries, nr_entries, GFP_ATOMIC);
+
+	spin_lock_irqsave(&dir->lock, flags);
+	if (tracker->dead) {
+		pr_err("reference already released.\n");
+		if (tracker->alloc_stack_handle) {
+			pr_err("allocated in:\n");
+			stack_depot_print(tracker->alloc_stack_handle);
+		}
+		if (tracker->free_stack_handle) {
+			pr_err("freed in:\n");
+			stack_depot_print(tracker->free_stack_handle);
+		}
+		spin_unlock_irqrestore(&dir->lock, flags);
+		WARN_ON_ONCE(1);
+		return -EINVAL;
+	}
+	tracker->dead = true;
+
+	tracker->free_stack_handle = stack_handle;
+
+	list_move_tail(&tracker->head, &dir->quarantine);
+	if (!dir->quarantine_avail) {
+		tracker = list_first_entry(&dir->quarantine, struct ref_tracker, head);
+		list_del(&tracker->head);
+	} else {
+		dir->quarantine_avail--;
+		tracker = NULL;
+	}
+	spin_unlock_irqrestore(&dir->lock, flags);
+
+	kfree(tracker);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ref_tracker_free);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/sha1.c
+++ linux-xilinx-zynqmp-5.15.0/lib/sha1.c
@@ -9,6 +9,7 @@
 #include <linux/kernel.h>
 #include <linux/export.h>
 #include <linux/bitops.h>
+#include <linux/string.h>
 #include <crypto/sha1.h>
 #include <asm/unaligned.h>
 
@@ -55,7 +56,8 @@
 #define SHA_ROUND(t, input, fn, constant, A, B, C, D, E) do { \
 	__u32 TEMP = input(t); setW(t, TEMP); \
 	E += TEMP + rol32(A,5) + (fn) + (constant); \
-	B = ror32(B, 2); } while (0)
+	B = ror32(B, 2); \
+	TEMP = E; E = D; D = C; C = B; B = A; A = TEMP; } while (0)
 
 #define T_0_15(t, A, B, C, D, E)  SHA_ROUND(t, SHA_SRC, (((C^D)&B)^D) , 0x5a827999, A, B, C, D, E )
 #define T_16_19(t, A, B, C, D, E) SHA_ROUND(t, SHA_MIX, (((C^D)&B)^D) , 0x5a827999, A, B, C, D, E )
@@ -84,6 +86,7 @@
 void sha1_transform(__u32 *digest, const char *data, __u32 *array)
 {
 	__u32 A, B, C, D, E;
+	unsigned int i = 0;
 
 	A = digest[0];
 	B = digest[1];
@@ -92,94 +95,24 @@
 	E = digest[4];
 
 	/* Round 1 - iterations 0-16 take their input from 'data' */
-	T_0_15( 0, A, B, C, D, E);
-	T_0_15( 1, E, A, B, C, D);
-	T_0_15( 2, D, E, A, B, C);
-	T_0_15( 3, C, D, E, A, B);
-	T_0_15( 4, B, C, D, E, A);
-	T_0_15( 5, A, B, C, D, E);
-	T_0_15( 6, E, A, B, C, D);
-	T_0_15( 7, D, E, A, B, C);
-	T_0_15( 8, C, D, E, A, B);
-	T_0_15( 9, B, C, D, E, A);
-	T_0_15(10, A, B, C, D, E);
-	T_0_15(11, E, A, B, C, D);
-	T_0_15(12, D, E, A, B, C);
-	T_0_15(13, C, D, E, A, B);
-	T_0_15(14, B, C, D, E, A);
-	T_0_15(15, A, B, C, D, E);
+	for (; i < 16; ++i)
+		T_0_15(i, A, B, C, D, E);
 
 	/* Round 1 - tail. Input from 512-bit mixing array */
-	T_16_19(16, E, A, B, C, D);
-	T_16_19(17, D, E, A, B, C);
-	T_16_19(18, C, D, E, A, B);
-	T_16_19(19, B, C, D, E, A);
+	for (; i < 20; ++i)
+		T_16_19(i, A, B, C, D, E);
 
 	/* Round 2 */
-	T_20_39(20, A, B, C, D, E);
-	T_20_39(21, E, A, B, C, D);
-	T_20_39(22, D, E, A, B, C);
-	T_20_39(23, C, D, E, A, B);
-	T_20_39(24, B, C, D, E, A);
-	T_20_39(25, A, B, C, D, E);
-	T_20_39(26, E, A, B, C, D);
-	T_20_39(27, D, E, A, B, C);
-	T_20_39(28, C, D, E, A, B);
-	T_20_39(29, B, C, D, E, A);
-	T_20_39(30, A, B, C, D, E);
-	T_20_39(31, E, A, B, C, D);
-	T_20_39(32, D, E, A, B, C);
-	T_20_39(33, C, D, E, A, B);
-	T_20_39(34, B, C, D, E, A);
-	T_20_39(35, A, B, C, D, E);
-	T_20_39(36, E, A, B, C, D);
-	T_20_39(37, D, E, A, B, C);
-	T_20_39(38, C, D, E, A, B);
-	T_20_39(39, B, C, D, E, A);
+	for (; i < 40; ++i)
+		T_20_39(i, A, B, C, D, E);
 
 	/* Round 3 */
-	T_40_59(40, A, B, C, D, E);
-	T_40_59(41, E, A, B, C, D);
-	T_40_59(42, D, E, A, B, C);
-	T_40_59(43, C, D, E, A, B);
-	T_40_59(44, B, C, D, E, A);
-	T_40_59(45, A, B, C, D, E);
-	T_40_59(46, E, A, B, C, D);
-	T_40_59(47, D, E, A, B, C);
-	T_40_59(48, C, D, E, A, B);
-	T_40_59(49, B, C, D, E, A);
-	T_40_59(50, A, B, C, D, E);
-	T_40_59(51, E, A, B, C, D);
-	T_40_59(52, D, E, A, B, C);
-	T_40_59(53, C, D, E, A, B);
-	T_40_59(54, B, C, D, E, A);
-	T_40_59(55, A, B, C, D, E);
-	T_40_59(56, E, A, B, C, D);
-	T_40_59(57, D, E, A, B, C);
-	T_40_59(58, C, D, E, A, B);
-	T_40_59(59, B, C, D, E, A);
+	for (; i < 60; ++i)
+		T_40_59(i, A, B, C, D, E);
 
 	/* Round 4 */
-	T_60_79(60, A, B, C, D, E);
-	T_60_79(61, E, A, B, C, D);
-	T_60_79(62, D, E, A, B, C);
-	T_60_79(63, C, D, E, A, B);
-	T_60_79(64, B, C, D, E, A);
-	T_60_79(65, A, B, C, D, E);
-	T_60_79(66, E, A, B, C, D);
-	T_60_79(67, D, E, A, B, C);
-	T_60_79(68, C, D, E, A, B);
-	T_60_79(69, B, C, D, E, A);
-	T_60_79(70, A, B, C, D, E);
-	T_60_79(71, E, A, B, C, D);
-	T_60_79(72, D, E, A, B, C);
-	T_60_79(73, C, D, E, A, B);
-	T_60_79(74, B, C, D, E, A);
-	T_60_79(75, A, B, C, D, E);
-	T_60_79(76, E, A, B, C, D);
-	T_60_79(77, D, E, A, B, C);
-	T_60_79(78, C, D, E, A, B);
-	T_60_79(79, B, C, D, E, A);
+	for (; i < 80; ++i)
+		T_60_79(i, A, B, C, D, E);
 
 	digest[0] += A;
 	digest[1] += B;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/siphash.c
+++ linux-xilinx-zynqmp-5.15.0/lib/siphash.c
@@ -18,19 +18,13 @@
 #include <asm/word-at-a-time.h>
 #endif
 
-#define SIPROUND \
-	do { \
-	v0 += v1; v1 = rol64(v1, 13); v1 ^= v0; v0 = rol64(v0, 32); \
-	v2 += v3; v3 = rol64(v3, 16); v3 ^= v2; \
-	v0 += v3; v3 = rol64(v3, 21); v3 ^= v0; \
-	v2 += v1; v1 = rol64(v1, 17); v1 ^= v2; v2 = rol64(v2, 32); \
-	} while (0)
+#define SIPROUND SIPHASH_PERMUTATION(v0, v1, v2, v3)
 
 #define PREAMBLE(len) \
-	u64 v0 = 0x736f6d6570736575ULL; \
-	u64 v1 = 0x646f72616e646f6dULL; \
-	u64 v2 = 0x6c7967656e657261ULL; \
-	u64 v3 = 0x7465646279746573ULL; \
+	u64 v0 = SIPHASH_CONST_0; \
+	u64 v1 = SIPHASH_CONST_1; \
+	u64 v2 = SIPHASH_CONST_2; \
+	u64 v3 = SIPHASH_CONST_3; \
 	u64 b = ((u64)(len)) << 56; \
 	v3 ^= key->key[1]; \
 	v2 ^= key->key[0]; \
@@ -49,6 +43,7 @@
 	SIPROUND; \
 	return (v0 ^ v1) ^ (v2 ^ v3);
 
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u64 __siphash_aligned(const void *data, size_t len, const siphash_key_t *key)
 {
 	const u8 *end = data + len - (len % sizeof(u64));
@@ -80,8 +75,8 @@
 	POSTAMBLE
 }
 EXPORT_SYMBOL(__siphash_aligned);
+#endif
 
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u64 __siphash_unaligned(const void *data, size_t len, const siphash_key_t *key)
 {
 	const u8 *end = data + len - (len % sizeof(u64));
@@ -113,7 +108,6 @@
 	POSTAMBLE
 }
 EXPORT_SYMBOL(__siphash_unaligned);
-#endif
 
 /**
  * siphash_1u64 - compute 64-bit siphash PRF value of a u64
@@ -250,6 +244,7 @@
 	HSIPROUND; \
 	return (v0 ^ v1) ^ (v2 ^ v3);
 
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u32 __hsiphash_aligned(const void *data, size_t len, const hsiphash_key_t *key)
 {
 	const u8 *end = data + len - (len % sizeof(u64));
@@ -280,8 +275,8 @@
 	HPOSTAMBLE
 }
 EXPORT_SYMBOL(__hsiphash_aligned);
+#endif
 
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u32 __hsiphash_unaligned(const void *data, size_t len,
 			 const hsiphash_key_t *key)
 {
@@ -313,7 +308,6 @@
 	HPOSTAMBLE
 }
 EXPORT_SYMBOL(__hsiphash_unaligned);
-#endif
 
 /**
  * hsiphash_1u32 - compute 64-bit hsiphash PRF value of a u32
@@ -389,19 +383,13 @@
 }
 EXPORT_SYMBOL(hsiphash_4u32);
 #else
-#define HSIPROUND \
-	do { \
-	v0 += v1; v1 = rol32(v1, 5); v1 ^= v0; v0 = rol32(v0, 16); \
-	v2 += v3; v3 = rol32(v3, 8); v3 ^= v2; \
-	v0 += v3; v3 = rol32(v3, 7); v3 ^= v0; \
-	v2 += v1; v1 = rol32(v1, 13); v1 ^= v2; v2 = rol32(v2, 16); \
-	} while (0)
+#define HSIPROUND HSIPHASH_PERMUTATION(v0, v1, v2, v3)
 
 #define HPREAMBLE(len) \
-	u32 v0 = 0; \
-	u32 v1 = 0; \
-	u32 v2 = 0x6c796765U; \
-	u32 v3 = 0x74656462U; \
+	u32 v0 = HSIPHASH_CONST_0; \
+	u32 v1 = HSIPHASH_CONST_1; \
+	u32 v2 = HSIPHASH_CONST_2; \
+	u32 v3 = HSIPHASH_CONST_3; \
 	u32 b = ((u32)(len)) << 24; \
 	v3 ^= key->key[1]; \
 	v2 ^= key->key[0]; \
@@ -418,6 +406,7 @@
 	HSIPROUND; \
 	return v1 ^ v3;
 
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u32 __hsiphash_aligned(const void *data, size_t len, const hsiphash_key_t *key)
 {
 	const u8 *end = data + len - (len % sizeof(u32));
@@ -438,8 +427,8 @@
 	HPOSTAMBLE
 }
 EXPORT_SYMBOL(__hsiphash_aligned);
+#endif
 
-#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
 u32 __hsiphash_unaligned(const void *data, size_t len,
 			 const hsiphash_key_t *key)
 {
@@ -461,7 +450,6 @@
 	HPOSTAMBLE
 }
 EXPORT_SYMBOL(__hsiphash_unaligned);
-#endif
 
 /**
  * hsiphash_1u32 - compute 32-bit hsiphash PRF value of a u32
--- linux-xilinx-zynqmp-5.15.0.orig/lib/slub_kunit.c
+++ linux-xilinx-zynqmp-5.15.0/lib/slub_kunit.c
@@ -39,7 +39,7 @@
 
 	ptr_addr = (unsigned long *)(p + s->offset);
 	tmp = *ptr_addr;
-	p[s->offset] = 0x12;
+	p[s->offset] = ~p[s->offset];
 
 	/*
 	 * Expecting three errors.
--- linux-xilinx-zynqmp-5.15.0.orig/lib/smp_processor_id.c
+++ linux-xilinx-zynqmp-5.15.0/lib/smp_processor_id.c
@@ -47,9 +47,9 @@
 
 	printk("caller is %pS\n", __builtin_return_address(0));
 	dump_stack();
-	instrumentation_end();
 
 out_enable:
+	instrumentation_end();
 	preempt_enable_no_resched_notrace();
 out:
 	return this_cpu;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/stackdepot.c
+++ linux-xilinx-zynqmp-5.15.0/lib/stackdepot.c
@@ -20,7 +20,6 @@
  */
 
 #include <linux/gfp.h>
-#include <linux/interrupt.h>
 #include <linux/jhash.h>
 #include <linux/kernel.h>
 #include <linux/mm.h>
@@ -295,10 +294,10 @@
 		/*
 		 * Zero out zone modifiers, as we don't have specific zone
 		 * requirements. Keep the flags related to allocation in atomic
-		 * contexts and I/O.
+		 * contexts, I/O, nolockdep.
 		 */
 		alloc_flags &= ~GFP_ZONEMASK;
-		alloc_flags &= (GFP_ATOMIC | GFP_KERNEL);
+		alloc_flags &= (GFP_ATOMIC | GFP_KERNEL | __GFP_NOLOCKDEP);
 		alloc_flags |= __GFP_NOWARN;
 		page = alloc_pages(alloc_flags, STACK_ALLOC_ORDER);
 		if (page)
@@ -341,26 +340,3 @@
 	return retval;
 }
 EXPORT_SYMBOL_GPL(stack_depot_save);
-
-static inline int in_irqentry_text(unsigned long ptr)
-{
-	return (ptr >= (unsigned long)&__irqentry_text_start &&
-		ptr < (unsigned long)&__irqentry_text_end) ||
-		(ptr >= (unsigned long)&__softirqentry_text_start &&
-		 ptr < (unsigned long)&__softirqentry_text_end);
-}
-
-unsigned int filter_irq_stacks(unsigned long *entries,
-					     unsigned int nr_entries)
-{
-	unsigned int i;
-
-	for (i = 0; i < nr_entries; i++) {
-		if (in_irqentry_text(entries[i])) {
-			/* Include the irqentry function into the stack. */
-			return i + 1;
-		}
-	}
-	return nr_entries;
-}
-EXPORT_SYMBOL_GPL(filter_irq_stacks);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/string_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/lib/string_helpers.c
@@ -51,7 +51,7 @@
 	static const unsigned int rounding[] = { 500, 50, 5 };
 	int i = 0, j;
 	u32 remainder = 0, sf_cap;
-	char tmp[8];
+	char tmp[12];
 	const char *unit;
 
 	tmp[0] = '\0';
@@ -696,3 +696,23 @@
 	kfree(array);
 }
 EXPORT_SYMBOL_GPL(kfree_strarray);
+
+/**
+ * memcpy_and_pad - Copy one buffer to another with padding
+ * @dest: Where to copy to
+ * @dest_len: The destination buffer size
+ * @src: Where to copy from
+ * @count: The number of bytes to copy
+ * @pad: Character to use for padding if space is left in destination.
+ */
+void memcpy_and_pad(void *dest, size_t dest_len, const void *src, size_t count,
+		    int pad)
+{
+	if (dest_len > count) {
+		memcpy(dest, src, count);
+		memset(dest + count, pad,  dest_len - count);
+	} else {
+		memcpy(dest, src, dest_len);
+	}
+}
+EXPORT_SYMBOL(memcpy_and_pad);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_blackhole_dev.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_blackhole_dev.c
@@ -29,7 +29,6 @@
 {
 	struct ipv6hdr *ip6h;
 	struct sk_buff *skb;
-	struct ethhdr *ethh;
 	struct udphdr *uh;
 	int data_len;
 	int ret;
@@ -61,7 +60,7 @@
 	ip6h->saddr = in6addr_loopback;
 	ip6h->daddr = in6addr_loopback;
 	/* Ether */
-	ethh = (struct ethhdr *)skb_push(skb, sizeof(struct ethhdr));
+	skb_push(skb, sizeof(struct ethhdr));
 	skb_set_mac_header(skb, 0);
 
 	skb->protocol = htons(ETH_P_IPV6);
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_bpf.c
@@ -8890,9 +8890,9 @@
 		.build_skb = build_test_skb_linear_no_head_frag,
 		.features = NETIF_F_SG | NETIF_F_FRAGLIST |
 			    NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_GSO |
-			    NETIF_F_LLTX_BIT | NETIF_F_GRO |
+			    NETIF_F_LLTX | NETIF_F_GRO |
 			    NETIF_F_IPV6_CSUM | NETIF_F_RXCSUM |
-			    NETIF_F_HW_VLAN_STAG_TX_BIT
+			    NETIF_F_HW_VLAN_STAG_TX
 	}
 };
 
@@ -8992,10 +8992,15 @@
 struct tail_call_test {
 	const char *descr;
 	struct bpf_insn insns[MAX_INSNS];
+	int flags;
 	int result;
 	int stack_depth;
 };
 
+/* Flags that can be passed to tail call test cases */
+#define FLAG_NEED_STATE		BIT(0)
+#define FLAG_RESULT_IN_STATE	BIT(1)
+
 /*
  * Magic marker used in test snippets for tail calls below.
  * BPF_LD/MOV to R2 and R2 with this immediate value is replaced
@@ -9065,32 +9070,38 @@
 	{
 		"Tail call error path, max count reached",
 		.insns = {
-			BPF_ALU64_IMM(BPF_ADD, R1, 1),
-			BPF_ALU64_REG(BPF_MOV, R0, R1),
+			BPF_LDX_MEM(BPF_W, R2, R1, 0),
+			BPF_ALU64_IMM(BPF_ADD, R2, 1),
+			BPF_STX_MEM(BPF_W, R1, R2, 0),
 			TAIL_CALL(0),
 			BPF_EXIT_INSN(),
 		},
-		.result = MAX_TAIL_CALL_CNT + 1,
+		.flags = FLAG_NEED_STATE | FLAG_RESULT_IN_STATE,
+		.result = (MAX_TAIL_CALL_CNT + 1 + 1) * MAX_TESTRUNS,
 	},
 	{
 		"Tail call error path, NULL target",
 		.insns = {
-			BPF_ALU64_IMM(BPF_MOV, R0, -1),
+			BPF_LDX_MEM(BPF_W, R2, R1, 0),
+			BPF_ALU64_IMM(BPF_ADD, R2, 1),
+			BPF_STX_MEM(BPF_W, R1, R2, 0),
 			TAIL_CALL(TAIL_CALL_NULL),
-			BPF_ALU64_IMM(BPF_MOV, R0, 1),
 			BPF_EXIT_INSN(),
 		},
-		.result = 1,
+		.flags = FLAG_NEED_STATE | FLAG_RESULT_IN_STATE,
+		.result = MAX_TESTRUNS,
 	},
 	{
 		"Tail call error path, index out of range",
 		.insns = {
-			BPF_ALU64_IMM(BPF_MOV, R0, -1),
+			BPF_LDX_MEM(BPF_W, R2, R1, 0),
+			BPF_ALU64_IMM(BPF_ADD, R2, 1),
+			BPF_STX_MEM(BPF_W, R1, R2, 0),
 			TAIL_CALL(TAIL_CALL_INVALID),
-			BPF_ALU64_IMM(BPF_MOV, R0, 1),
 			BPF_EXIT_INSN(),
 		},
-		.result = 1,
+		.flags = FLAG_NEED_STATE | FLAG_RESULT_IN_STATE,
+		.result = MAX_TESTRUNS,
 	},
 };
 
@@ -9196,6 +9207,8 @@
 	for (i = 0; i < ARRAY_SIZE(tail_call_tests); i++) {
 		struct tail_call_test *test = &tail_call_tests[i];
 		struct bpf_prog *fp = progs->ptrs[i];
+		int *data = NULL;
+		int state = 0;
 		u64 duration;
 		int ret;
 
@@ -9212,7 +9225,11 @@
 		if (fp->jited)
 			jit_cnt++;
 
-		ret = __run_one(fp, NULL, MAX_TESTRUNS, &duration);
+		if (test->flags & FLAG_NEED_STATE)
+			data = &state;
+		ret = __run_one(fp, data, MAX_TESTRUNS, &duration);
+		if (test->flags & FLAG_RESULT_IN_STATE)
+			ret = state;
 		if (ret == test->result) {
 			pr_cont("%lld PASS", duration);
 			pass_cnt++;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_firmware.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_firmware.c
@@ -22,6 +22,7 @@
 #include <linux/slab.h>
 #include <linux/uaccess.h>
 #include <linux/delay.h>
+#include <linux/kstrtox.h>
 #include <linux/kthread.h>
 #include <linux/vmalloc.h>
 #include <linux/efi_embedded_fw.h>
@@ -41,6 +42,7 @@
 	bool sent;
 	const struct firmware *fw;
 	const char *name;
+	const char *fw_buf;
 	struct completion completion;
 	struct task_struct *task;
 	struct device *dev;
@@ -143,8 +145,14 @@
 
 	for (i = 0; i < test_fw_config->num_requests; i++) {
 		req = &test_fw_config->reqs[i];
-		if (req->fw)
+		if (req->fw) {
+			if (req->fw_buf) {
+				kfree_const(req->fw_buf);
+				req->fw_buf = NULL;
+			}
 			release_firmware(req->fw);
+			req->fw = NULL;
+		}
 	}
 
 	vfree(test_fw_config->reqs);
@@ -175,7 +183,7 @@
 {
 	*dst = kstrndup(name, count, gfp);
 	if (!*dst)
-		return -ENOSPC;
+		return -ENOMEM;
 	return count;
 }
 
@@ -313,16 +321,26 @@
 	return len;
 }
 
-static int test_dev_config_update_bool(const char *buf, size_t size,
+static inline int __test_dev_config_update_bool(const char *buf, size_t size,
 				       bool *cfg)
 {
 	int ret;
 
-	mutex_lock(&test_fw_mutex);
-	if (strtobool(buf, cfg) < 0)
+	if (kstrtobool(buf, cfg) < 0)
 		ret = -EINVAL;
 	else
 		ret = size;
+
+	return ret;
+}
+
+static int test_dev_config_update_bool(const char *buf, size_t size,
+				       bool *cfg)
+{
+	int ret;
+
+	mutex_lock(&test_fw_mutex);
+	ret = __test_dev_config_update_bool(buf, size, cfg);
 	mutex_unlock(&test_fw_mutex);
 
 	return ret;
@@ -333,7 +351,8 @@
 	return snprintf(buf, PAGE_SIZE, "%d\n", val);
 }
 
-static int test_dev_config_update_size_t(const char *buf,
+static int __test_dev_config_update_size_t(
+					 const char *buf,
 					 size_t size,
 					 size_t *cfg)
 {
@@ -344,9 +363,7 @@
 	if (ret)
 		return ret;
 
-	mutex_lock(&test_fw_mutex);
 	*(size_t *)cfg = new;
-	mutex_unlock(&test_fw_mutex);
 
 	/* Always return full write size even if we didn't consume all */
 	return size;
@@ -362,7 +379,7 @@
 	return snprintf(buf, PAGE_SIZE, "%d\n", val);
 }
 
-static int test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
+static int __test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
 {
 	u8 val;
 	int ret;
@@ -371,14 +388,23 @@
 	if (ret)
 		return ret;
 
-	mutex_lock(&test_fw_mutex);
 	*(u8 *)cfg = val;
-	mutex_unlock(&test_fw_mutex);
 
 	/* Always return full write size even if we didn't consume all */
 	return size;
 }
 
+static int test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
+{
+	int ret;
+
+	mutex_lock(&test_fw_mutex);
+	ret = __test_dev_config_update_u8(buf, size, cfg);
+	mutex_unlock(&test_fw_mutex);
+
+	return ret;
+}
+
 static ssize_t test_dev_config_show_u8(char *buf, u8 val)
 {
 	return snprintf(buf, PAGE_SIZE, "%u\n", val);
@@ -405,10 +431,10 @@
 		mutex_unlock(&test_fw_mutex);
 		goto out;
 	}
-	mutex_unlock(&test_fw_mutex);
 
-	rc = test_dev_config_update_u8(buf, count,
-				       &test_fw_config->num_requests);
+	rc = __test_dev_config_update_u8(buf, count,
+					 &test_fw_config->num_requests);
+	mutex_unlock(&test_fw_mutex);
 
 out:
 	return rc;
@@ -452,10 +478,10 @@
 		mutex_unlock(&test_fw_mutex);
 		goto out;
 	}
-	mutex_unlock(&test_fw_mutex);
 
-	rc = test_dev_config_update_size_t(buf, count,
-					   &test_fw_config->buf_size);
+	rc = __test_dev_config_update_size_t(buf, count,
+					     &test_fw_config->buf_size);
+	mutex_unlock(&test_fw_mutex);
 
 out:
 	return rc;
@@ -482,10 +508,10 @@
 		mutex_unlock(&test_fw_mutex);
 		goto out;
 	}
-	mutex_unlock(&test_fw_mutex);
 
-	rc = test_dev_config_update_size_t(buf, count,
-					   &test_fw_config->file_offset);
+	rc = __test_dev_config_update_size_t(buf, count,
+					     &test_fw_config->file_offset);
+	mutex_unlock(&test_fw_mutex);
 
 out:
 	return rc;
@@ -580,12 +606,14 @@
 
 	name = kstrndup(buf, count, GFP_KERNEL);
 	if (!name)
-		return -ENOSPC;
+		return -ENOMEM;
 
 	pr_info("loading '%s'\n", name);
 
 	mutex_lock(&test_fw_mutex);
 	release_firmware(test_firmware);
+	if (test_fw_config->reqs)
+		__test_release_all_firmware();
 	test_firmware = NULL;
 	rc = request_firmware(&test_firmware, name, dev);
 	if (rc) {
@@ -626,7 +654,7 @@
 
 	name = kstrndup(buf, count, GFP_KERNEL);
 	if (!name)
-		return -ENOSPC;
+		return -ENOMEM;
 
 	pr_info("inserting test platform fw '%s'\n", name);
 	efi_embedded_fw.name = name;
@@ -679,13 +707,15 @@
 
 	name = kstrndup(buf, count, GFP_KERNEL);
 	if (!name)
-		return -ENOSPC;
+		return -ENOMEM;
 
 	pr_info("loading '%s'\n", name);
 
 	mutex_lock(&test_fw_mutex);
 	release_firmware(test_firmware);
 	test_firmware = NULL;
+	if (test_fw_config->reqs)
+		__test_release_all_firmware();
 	rc = request_firmware_nowait(THIS_MODULE, 1, name, dev, GFP_KERNEL,
 				     NULL, trigger_async_request_cb);
 	if (rc) {
@@ -722,12 +752,14 @@
 
 	name = kstrndup(buf, count, GFP_KERNEL);
 	if (!name)
-		return -ENOSPC;
+		return -ENOMEM;
 
 	pr_info("loading '%s' using custom fallback mechanism\n", name);
 
 	mutex_lock(&test_fw_mutex);
 	release_firmware(test_firmware);
+	if (test_fw_config->reqs)
+		__test_release_all_firmware();
 	test_firmware = NULL;
 	rc = request_firmware_nowait(THIS_MODULE, FW_ACTION_NOUEVENT, name,
 				     dev, GFP_KERNEL, NULL,
@@ -771,7 +803,7 @@
 
 		test_buf = kzalloc(TEST_FIRMWARE_BUF_SIZE, GFP_KERNEL);
 		if (!test_buf)
-			return -ENOSPC;
+			return -ENOMEM;
 
 		if (test_fw_config->partial)
 			req->rc = request_partial_firmware_into_buf
@@ -790,6 +822,8 @@
 						 test_fw_config->buf_size);
 		if (!req->fw)
 			kfree(test_buf);
+		else
+			req->fw_buf = test_buf;
 	} else {
 		req->rc = test_fw_config->req_firmware(&req->fw,
 						       req->name,
@@ -829,6 +863,11 @@
 
 	mutex_lock(&test_fw_mutex);
 
+	if (test_fw_config->reqs) {
+		rc = -EBUSY;
+		goto out_bail;
+	}
+
 	test_fw_config->reqs =
 		vzalloc(array3_size(sizeof(struct test_batched_req),
 				    test_fw_config->num_requests, 2));
@@ -845,6 +884,7 @@
 		req->fw = NULL;
 		req->idx = i;
 		req->name = test_fw_config->name;
+		req->fw_buf = NULL;
 		req->dev = dev;
 		init_completion(&req->completion);
 		req->task = kthread_run(test_fw_run_batch_request, req,
@@ -927,6 +967,11 @@
 
 	mutex_lock(&test_fw_mutex);
 
+	if (test_fw_config->reqs) {
+		rc = -EBUSY;
+		goto out_bail;
+	}
+
 	test_fw_config->reqs =
 		vzalloc(array3_size(sizeof(struct test_batched_req),
 				    test_fw_config->num_requests, 2));
@@ -944,6 +989,7 @@
 	for (i = 0; i < test_fw_config->num_requests; i++) {
 		req = &test_fw_config->reqs[i];
 		req->name = test_fw_config->name;
+		req->fw_buf = NULL;
 		req->fw = NULL;
 		req->idx = i;
 		init_completion(&req->completion);
@@ -1111,6 +1157,7 @@
 
 	rc = misc_register(&test_fw_misc_device);
 	if (rc) {
+		__test_firmware_config_free();
 		kfree(test_fw_config);
 		pr_err("could not register misc device: %d\n", rc);
 		return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_hmm.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_hmm.c
@@ -731,7 +731,7 @@
 
 	mmap_read_lock(mm);
 	for (addr = start; addr < end; addr = next) {
-		unsigned long mapped;
+		unsigned long mapped = 0;
 		int i;
 
 		if (end < addr + (ARRAY_SIZE(pages) << PAGE_SHIFT))
@@ -740,7 +740,13 @@
 			next = addr + (ARRAY_SIZE(pages) << PAGE_SHIFT);
 
 		ret = make_device_exclusive_range(mm, addr, next, pages, NULL);
-		mapped = dmirror_atomic_map(addr, next, pages, dmirror);
+		/*
+		 * Do dmirror_atomic_map() iff all pages are marked for
+		 * exclusive access to avoid accessing uninitialized
+		 * fields of pages.
+		 */
+		if (ret == (next - addr) >> PAGE_SHIFT)
+			mapped = dmirror_atomic_map(addr, next, pages, dmirror);
 		for (i = 0; i < ret; i++) {
 			if (pages[i]) {
 				unlock_page(pages[i]);
@@ -1087,9 +1093,33 @@
 	return 0;
 }
 
+static int dmirror_fops_mmap(struct file *file, struct vm_area_struct *vma)
+{
+	unsigned long addr;
+
+	for (addr = vma->vm_start; addr < vma->vm_end; addr += PAGE_SIZE) {
+		struct page *page;
+		int ret;
+
+		page = alloc_page(GFP_KERNEL | __GFP_ZERO);
+		if (!page)
+			return -ENOMEM;
+
+		ret = vm_insert_page(vma, addr, page);
+		if (ret) {
+			__free_page(page);
+			return ret;
+		}
+		put_page(page);
+	}
+
+	return 0;
+}
+
 static const struct file_operations dmirror_fops = {
 	.open		= dmirror_fops_open,
 	.release	= dmirror_fops_release,
+	.mmap		= dmirror_fops_mmap,
 	.unlocked_ioctl = dmirror_fops_unlocked_ioctl,
 	.llseek		= default_llseek,
 	.owner		= THIS_MODULE,
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_ida.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_ida.c
@@ -150,6 +150,45 @@
 	IDA_BUG_ON(ida, !ida_is_empty(ida));
 }
 
+/*
+ * Check various situations where we attempt to free an ID we don't own.
+ */
+static void ida_check_bad_free(struct ida *ida)
+{
+	unsigned long i;
+
+	printk("vvv Ignore \"not allocated\" warnings\n");
+	/* IDA is empty; all of these will fail */
+	ida_free(ida, 0);
+	for (i = 0; i < 31; i++)
+		ida_free(ida, 1 << i);
+
+	/* IDA contains a single value entry */
+	IDA_BUG_ON(ida, ida_alloc_min(ida, 3, GFP_KERNEL) != 3);
+	ida_free(ida, 0);
+	for (i = 0; i < 31; i++)
+		ida_free(ida, 1 << i);
+
+	/* IDA contains a single bitmap */
+	IDA_BUG_ON(ida, ida_alloc_min(ida, 1023, GFP_KERNEL) != 1023);
+	ida_free(ida, 0);
+	for (i = 0; i < 31; i++)
+		ida_free(ida, 1 << i);
+
+	/* IDA contains a tree */
+	IDA_BUG_ON(ida, ida_alloc_min(ida, (1 << 20) - 1, GFP_KERNEL) != (1 << 20) - 1);
+	ida_free(ida, 0);
+	for (i = 0; i < 31; i++)
+		ida_free(ida, 1 << i);
+	printk("^^^ \"not allocated\" warnings over\n");
+
+	ida_free(ida, 3);
+	ida_free(ida, 1023);
+	ida_free(ida, (1 << 20) - 1);
+
+	IDA_BUG_ON(ida, !ida_is_empty(ida));
+}
+
 static DEFINE_IDA(ida);
 
 static int ida_checks(void)
@@ -162,6 +201,7 @@
 	ida_check_leaf(&ida, 1024 * 64);
 	ida_check_max(&ida);
 	ida_check_conv(&ida);
+	ida_check_bad_free(&ida);
 
 	printk("IDA: %u of %u tests passed\n", tests_passed, tests_run);
 	return (tests_run != tests_passed) ? 0 : -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_kasan.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_kasan.c
@@ -125,6 +125,7 @@
 	ptr = kmalloc(size, GFP_KERNEL);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
 	/*
 	 * An unaligned access past the requested kmalloc size.
 	 * Only generic KASAN can precisely detect these.
@@ -153,6 +154,7 @@
 	ptr = kmalloc(size, GFP_KERNEL);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
 	KUNIT_EXPECT_KASAN_FAIL(test, *ptr = *(ptr - 1));
 	kfree(ptr);
 }
@@ -165,6 +167,7 @@
 	ptr = kmalloc_node(size, GFP_KERNEL, 0);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
 	KUNIT_EXPECT_KASAN_FAIL(test, ptr[0] = ptr[size]);
 	kfree(ptr);
 }
@@ -185,6 +188,7 @@
 	ptr = kmalloc(size, GFP_KERNEL);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
 	KUNIT_EXPECT_KASAN_FAIL(test, ptr[size + OOB_TAG_OFF] = 0);
 
 	kfree(ptr);
@@ -265,6 +269,7 @@
 	ptr = kmalloc(size, GFP_KERNEL);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
 	KUNIT_EXPECT_KASAN_FAIL(test, ptr[size] = 0);
 	kfree(ptr);
 }
@@ -398,12 +403,15 @@
 	/* This test is specifically crafted for the generic mode. */
 	KASAN_TEST_NEEDS_CONFIG_ON(test, CONFIG_KASAN_GENERIC);
 
-	ptr1 = kmalloc(sizeof(*ptr1) - 3, GFP_KERNEL);
+	/* RELOC_HIDE to prevent gcc from warning about short alloc */
+	ptr1 = RELOC_HIDE(kmalloc(sizeof(*ptr1) - 3, GFP_KERNEL), 0);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr1);
 
 	ptr2 = kmalloc(sizeof(*ptr2), GFP_KERNEL);
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr2);
 
+	OPTIMIZER_HIDE_VAR(ptr1);
+	OPTIMIZER_HIDE_VAR(ptr2);
 	KUNIT_EXPECT_KASAN_FAIL(test, *ptr1 = *ptr2);
 	kfree(ptr1);
 	kfree(ptr2);
@@ -493,7 +501,7 @@
 	kfree(ptr);
 }
 
-static void kmalloc_memmove_invalid_size(struct kunit *test)
+static void kmalloc_memmove_negative_size(struct kunit *test)
 {
 	char *ptr;
 	size_t size = 64;
@@ -515,6 +523,21 @@
 	kfree(ptr);
 }
 
+static void kmalloc_memmove_invalid_size(struct kunit *test)
+{
+	char *ptr;
+	size_t size = 64;
+	volatile size_t invalid_size = size;
+
+	ptr = kmalloc(size, GFP_KERNEL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
+
+	memset((char *)ptr, 0, 64);
+	KUNIT_EXPECT_KASAN_FAIL(test,
+		memmove((char *)ptr, (char *)ptr + 4, invalid_size));
+	kfree(ptr);
+}
+
 static void kmalloc_uaf(struct kunit *test)
 {
 	char *ptr;
@@ -712,6 +735,8 @@
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 	real_size = ksize(ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
+
 	/* This access shouldn't trigger a KASAN report. */
 	ptr[size] = 'x';
 
@@ -734,6 +759,7 @@
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ptr);
 	kfree(ptr);
 
+	OPTIMIZER_HIDE_VAR(ptr);
 	KUNIT_EXPECT_KASAN_FAIL(test, ksize(ptr));
 	KUNIT_EXPECT_KASAN_FAIL(test, ((volatile char *)ptr)[0]);
 	KUNIT_EXPECT_KASAN_FAIL(test, ((volatile char *)ptr)[size]);
@@ -1129,6 +1155,7 @@
 	KUNIT_CASE(kmalloc_oob_memset_4),
 	KUNIT_CASE(kmalloc_oob_memset_8),
 	KUNIT_CASE(kmalloc_oob_memset_16),
+	KUNIT_CASE(kmalloc_memmove_negative_size),
 	KUNIT_CASE(kmalloc_memmove_invalid_size),
 	KUNIT_CASE(kmalloc_uaf),
 	KUNIT_CASE(kmalloc_uaf_memset),
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_kmod.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_kmod.c
@@ -1149,6 +1149,7 @@
 	if (ret) {
 		pr_err("could not register misc device: %d\n", ret);
 		free_test_dev_kmod(test_dev);
+		test_dev = NULL;
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_lockup.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_lockup.c
@@ -417,9 +417,14 @@
 		return false;
 
 	/* should be at least readable kernel address */
-	if (access_ok(ptr, 1) ||
-	    access_ok(ptr + size - 1, 1) ||
-	    get_kernel_nofault(buf, ptr) ||
+	if (!IS_ENABLED(CONFIG_ALTERNATE_USER_ADDRESS_SPACE) &&
+	    (access_ok((void __user *)ptr, 1) ||
+	     access_ok((void __user *)ptr + size - 1, 1))) {
+		pr_err("user space ptr invalid in kernel: %#lx\n", addr);
+		return true;
+	}
+
+	if (get_kernel_nofault(buf, ptr) ||
 	    get_kernel_nofault(buf, ptr + size - 1)) {
 		pr_err("invalid kernel ptr: %#lx\n", addr);
 		return true;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_meminit.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_meminit.c
@@ -86,7 +86,7 @@
 	int failures = 0, num_tests = 0;
 	int i;
 
-	for (i = 0; i < 10; i++)
+	for (i = 0; i < MAX_ORDER; i++)
 		num_tests += do_alloc_pages_order(i, &failures);
 
 	REPORT_FAILURES_IN_FN();
@@ -337,6 +337,7 @@
 		if (num)
 			kmem_cache_free_bulk(c, num, objects);
 	}
+	kmem_cache_destroy(c);
 	*total_failures += fail;
 	return 1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_overflow.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_overflow.c
@@ -588,12 +588,110 @@
 	return err;
 }
 
+struct __test_flex_array {
+	unsigned long flags;
+	size_t count;
+	unsigned long data[];
+};
+
+static int __init test_overflow_size_helpers(void)
+{
+	struct __test_flex_array *obj;
+	int count = 0;
+	int err = 0;
+	int var;
+
+#define check_one_size_helper(expected, func, args...)	({	\
+	bool __failure = false;					\
+	size_t _r;						\
+								\
+	_r = func(args);					\
+	if (_r != (expected)) {					\
+		pr_warn("expected " #func "(" #args ") "	\
+			"to return %zu but got %zu instead\n",	\
+			(size_t)(expected), _r);		\
+		__failure = true;				\
+	}							\
+	count++;						\
+	__failure;						\
+})
+
+	var = 4;
+	err |= check_one_size_helper(20,       size_mul, var++, 5);
+	err |= check_one_size_helper(20,       size_mul, 4, var++);
+	err |= check_one_size_helper(0,	       size_mul, 0, 3);
+	err |= check_one_size_helper(0,	       size_mul, 3, 0);
+	err |= check_one_size_helper(6,	       size_mul, 2, 3);
+	err |= check_one_size_helper(SIZE_MAX, size_mul, SIZE_MAX,  1);
+	err |= check_one_size_helper(SIZE_MAX, size_mul, SIZE_MAX,  3);
+	err |= check_one_size_helper(SIZE_MAX, size_mul, SIZE_MAX, -3);
+
+	var = 4;
+	err |= check_one_size_helper(9,        size_add, var++, 5);
+	err |= check_one_size_helper(9,        size_add, 4, var++);
+	err |= check_one_size_helper(9,	       size_add, 9, 0);
+	err |= check_one_size_helper(9,	       size_add, 0, 9);
+	err |= check_one_size_helper(5,	       size_add, 2, 3);
+	err |= check_one_size_helper(SIZE_MAX, size_add, SIZE_MAX,  1);
+	err |= check_one_size_helper(SIZE_MAX, size_add, SIZE_MAX,  3);
+	err |= check_one_size_helper(SIZE_MAX, size_add, SIZE_MAX, -3);
+
+	var = 4;
+	err |= check_one_size_helper(1,        size_sub, var--, 3);
+	err |= check_one_size_helper(1,        size_sub, 4, var--);
+	err |= check_one_size_helper(1,        size_sub, 3, 2);
+	err |= check_one_size_helper(9,	       size_sub, 9, 0);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, 9, -3);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, 0, 9);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, 2, 3);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, SIZE_MAX,  0);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, SIZE_MAX, 10);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, 0,  SIZE_MAX);
+	err |= check_one_size_helper(SIZE_MAX, size_sub, 14, SIZE_MAX);
+	err |= check_one_size_helper(SIZE_MAX - 2, size_sub, SIZE_MAX - 1,  1);
+	err |= check_one_size_helper(SIZE_MAX - 4, size_sub, SIZE_MAX - 1,  3);
+	err |= check_one_size_helper(1,		size_sub, SIZE_MAX - 1, -3);
+
+	var = 4;
+	err |= check_one_size_helper(4 * sizeof(*obj->data),
+				     flex_array_size, obj, data, var++);
+	err |= check_one_size_helper(5 * sizeof(*obj->data),
+				     flex_array_size, obj, data, var++);
+	err |= check_one_size_helper(0, flex_array_size, obj, data, 0);
+	err |= check_one_size_helper(sizeof(*obj->data),
+				     flex_array_size, obj, data, 1);
+	err |= check_one_size_helper(7 * sizeof(*obj->data),
+				     flex_array_size, obj, data, 7);
+	err |= check_one_size_helper(SIZE_MAX,
+				     flex_array_size, obj, data, -1);
+	err |= check_one_size_helper(SIZE_MAX,
+				     flex_array_size, obj, data, SIZE_MAX - 4);
+
+	var = 4;
+	err |= check_one_size_helper(sizeof(*obj) + (4 * sizeof(*obj->data)),
+				     struct_size, obj, data, var++);
+	err |= check_one_size_helper(sizeof(*obj) + (5 * sizeof(*obj->data)),
+				     struct_size, obj, data, var++);
+	err |= check_one_size_helper(sizeof(*obj), struct_size, obj, data, 0);
+	err |= check_one_size_helper(sizeof(*obj) + sizeof(*obj->data),
+				     struct_size, obj, data, 1);
+	err |= check_one_size_helper(SIZE_MAX,
+				     struct_size, obj, data, -3);
+	err |= check_one_size_helper(SIZE_MAX,
+				     struct_size, obj, data, SIZE_MAX - 3);
+
+	pr_info("%d overflow size helper tests finished\n", count);
+
+	return err;
+}
+
 static int __init test_module_init(void)
 {
 	int err = 0;
 
 	err |= test_overflow_calculation();
 	err |= test_overflow_shift();
+	err |= test_overflow_size_helpers();
 	err |= test_overflow_allocation();
 
 	if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_scanf.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_scanf.c
@@ -606,7 +606,7 @@
 #define test_number_prefix(T, str, scan_fmt, expect0, expect1, n_args, fn)	\
 do {										\
 	const T expect[2] = { expect0, expect1 };				\
-	T result[2] = {~expect[0], ~expect[1]};					\
+	T result[2] = { (T)~expect[0], (T)~expect[1] };				\
 										\
 	_test(fn, &expect, str, scan_fmt, n_args, &result[0], &result[1]);	\
 } while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_stackinit.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_stackinit.c
@@ -259,6 +259,7 @@
 static noinline __init DO_NOTHING_TYPE_ ## which(var_type)	\
 do_nothing_ ## name(var_type *ptr)				\
 {								\
+	OPTIMIZER_HIDE_VAR(ptr);				\
 	/* Will always be true, but compiler doesn't know. */	\
 	if ((unsigned long)ptr > 0x2)				\
 		return DO_NOTHING_RETURN_ ## which(ptr);	\
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_ubsan.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_ubsan.c
@@ -79,15 +79,6 @@
 	eval2 = eval;
 }
 
-static void test_ubsan_null_ptr_deref(void)
-{
-	volatile int *ptr = NULL;
-	int val;
-
-	UBSAN_TEST(CONFIG_UBSAN_OBJECT_SIZE);
-	val = *ptr;
-}
-
 static void test_ubsan_misaligned_access(void)
 {
 	volatile char arr[5] __aligned(4) = {1, 2, 3, 4, 5};
@@ -98,29 +89,16 @@
 	*ptr = val;
 }
 
-static void test_ubsan_object_size_mismatch(void)
-{
-	/* "((aligned(8)))" helps this not into be misaligned for ptr-access. */
-	volatile int val __aligned(8) = 4;
-	volatile long long *ptr, val2;
-
-	UBSAN_TEST(CONFIG_UBSAN_OBJECT_SIZE);
-	ptr = (long long *)&val;
-	val2 = *ptr;
-}
-
 static const test_ubsan_fp test_ubsan_array[] = {
 	test_ubsan_shift_out_of_bounds,
 	test_ubsan_out_of_bounds,
 	test_ubsan_load_invalid_value,
 	test_ubsan_misaligned_access,
-	test_ubsan_object_size_mismatch,
 };
 
 /* Excluded because they Oops the module. */
 static const test_ubsan_fp skip_ubsan_array[] = {
 	test_ubsan_divrem_overflow,
-	test_ubsan_null_ptr_deref,
 };
 
 static int __init test_ubsan_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/test_xarray.c
+++ linux-xilinx-zynqmp-5.15.0/lib/test_xarray.c
@@ -1463,6 +1463,25 @@
 	XA_BUG_ON(xa, !xa_empty(xa));
 }
 
+static noinline void check_create_range_5(struct xarray *xa,
+		unsigned long index, unsigned int order)
+{
+	XA_STATE_ORDER(xas, xa, index, order);
+	unsigned int i;
+
+	xa_store_order(xa, index, order, xa_mk_index(index), GFP_KERNEL);
+
+	for (i = 0; i < order + 10; i++) {
+		do {
+			xas_lock(&xas);
+			xas_create_range(&xas);
+			xas_unlock(&xas);
+		} while (xas_nomem(&xas, GFP_KERNEL));
+	}
+
+	xa_destroy(xa);
+}
+
 static noinline void check_create_range(struct xarray *xa)
 {
 	unsigned int order;
@@ -1490,6 +1509,9 @@
 		check_create_range_4(xa, (3U << order) + 1, order);
 		check_create_range_4(xa, (3U << order) - 1, order);
 		check_create_range_4(xa, (1U << 24) + 1, order);
+
+		check_create_range_5(xa, 0, order);
+		check_create_range_5(xa, (1U << order), order);
 	}
 
 	check_create_range_3();
--- linux-xilinx-zynqmp-5.15.0.orig/lib/ts_bm.c
+++ linux-xilinx-zynqmp-5.15.0/lib/ts_bm.c
@@ -60,10 +60,12 @@
 	struct ts_bm *bm = ts_config_priv(conf);
 	unsigned int i, text_len, consumed = state->offset;
 	const u8 *text;
-	int shift = bm->patlen - 1, bs;
+	int bs;
 	const u8 icase = conf->flags & TS_IGNORECASE;
 
 	for (;;) {
+		int shift = bm->patlen - 1;
+
 		text_len = conf->get_next_block(consumed, &text, conf, state);
 
 		if (unlikely(text_len == 0))
--- linux-xilinx-zynqmp-5.15.0.orig/lib/ubsan.c
+++ linux-xilinx-zynqmp-5.15.0/lib/ubsan.c
@@ -154,16 +154,7 @@
 
 	current->in_ubsan--;
 
-	if (panic_on_warn) {
-		/*
-		 * This thread may hit another WARN() in the panic path.
-		 * Resetting this prevents additional WARN() from panicking the
-		 * system on this thread.  Other threads are blocked by the
-		 * panic_mutex in panic().
-		 */
-		panic_on_warn = 0;
-		panic("panic_on_warn set ...\n");
-	}
+	check_panic_on_warn("UBSAN");
 }
 
 void __ubsan_handle_divrem_overflow(void *_data, void *lhs, void *rhs)
--- linux-xilinx-zynqmp-5.15.0.orig/lib/usercopy.c
+++ linux-xilinx-zynqmp-5.15.0/lib/usercopy.c
@@ -3,6 +3,7 @@
 #include <linux/fault-inject-usercopy.h>
 #include <linux/instrumented.h>
 #include <linux/uaccess.h>
+#include <linux/nospec.h>
 
 /* out-of-line parts */
 
@@ -12,6 +13,12 @@
 	unsigned long res = n;
 	might_fault();
 	if (!should_fail_usercopy() && likely(access_ok(from, n))) {
+		/*
+		 * Ensure that bad access_ok() speculation will not
+		 * lead to nasty side effects *after* the copy is
+		 * finished:
+		 */
+		barrier_nospec();
 		instrument_copy_from_user(to, from, n);
 		res = raw_copy_from_user(to, from, n);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/lib/vdso/Makefile
+++ linux-xilinx-zynqmp-5.15.0/lib/vdso/Makefile
@@ -17,6 +17,6 @@
 endif
 
 quiet_cmd_vdso_check = VDSOCHK $@
-      cmd_vdso_check = if $(OBJDUMP) -R $@ | egrep -h "$(ARCH_REL_TYPE_ABS)"; \
+      cmd_vdso_check = if $(OBJDUMP) -R $@ | grep -E -h "$(ARCH_REL_TYPE_ABS)"; \
 		       then (echo >&2 "$@: dynamic relocations are not supported"; \
 			     rm -f $@; /bin/false); fi
--- linux-xilinx-zynqmp-5.15.0.orig/lib/vsprintf.c
+++ linux-xilinx-zynqmp-5.15.0/lib/vsprintf.c
@@ -49,12 +49,16 @@
 
 #include <asm/page.h>		/* for PAGE_SIZE */
 #include <asm/byteorder.h>	/* cpu_to_le16 */
+#include <asm/unaligned.h>
 
 #include <linux/string_helpers.h>
 #include "kstrtox.h"
 
-static unsigned long long simple_strntoull(const char *startp, size_t max_chars,
-					   char **endp, unsigned int base)
+/* Disable pointer hashing if requested */
+bool no_hash_pointers __ro_after_init;
+EXPORT_SYMBOL_GPL(no_hash_pointers);
+
+static noinline unsigned long long simple_strntoull(const char *startp, size_t max_chars, char **endp, unsigned int base)
 {
 	const char *cp;
 	unsigned long long result = 0ULL;
@@ -757,14 +761,16 @@
 
 static DECLARE_WORK(enable_ptr_key_work, enable_ptr_key_workfn);
 
-static void fill_random_ptr_key(struct random_ready_callback *unused)
+static int fill_random_ptr_key(struct notifier_block *nb,
+			       unsigned long action, void *data)
 {
 	/* This may be in an interrupt handler. */
 	queue_work(system_unbound_wq, &enable_ptr_key_work);
+	return 0;
 }
 
-static struct random_ready_callback random_ready = {
-	.func = fill_random_ptr_key
+static struct notifier_block random_ready = {
+	.notifier_call = fill_random_ptr_key
 };
 
 static int __init initialize_ptr_random(void)
@@ -778,7 +784,7 @@
 		return 0;
 	}
 
-	ret = add_random_ready_callback(&random_ready);
+	ret = register_random_ready_notifier(&random_ready);
 	if (!ret) {
 		return 0;
 	} else if (ret == -EALREADY) {
@@ -848,6 +854,19 @@
 	return pointer_string(buf, end, (const void *)hashval, spec);
 }
 
+static char *default_pointer(char *buf, char *end, const void *ptr,
+			     struct printf_spec spec)
+{
+	/*
+	 * default is to _not_ leak addresses, so hash before printing,
+	 * unless no_hash_pointers is specified on the command line.
+	 */
+	if (unlikely(no_hash_pointers))
+		return pointer_string(buf, end, ptr, spec);
+
+	return ptr_to_id(buf, end, ptr, spec);
+}
+
 int kptr_restrict __read_mostly;
 
 static noinline_for_stack
@@ -857,7 +876,7 @@
 	switch (kptr_restrict) {
 	case 0:
 		/* Handle as %p, hash and do _not_ leak addresses. */
-		return ptr_to_id(buf, end, ptr, spec);
+		return default_pointer(buf, end, ptr, spec);
 	case 1: {
 		const struct cred *cred;
 
@@ -1771,7 +1790,7 @@
 	char output[sizeof("0123 little-endian (0x01234567)")];
 	char *p = output;
 	unsigned int i;
-	u32 val;
+	u32 orig, val;
 
 	if (fmt[1] != 'c' || fmt[2] != 'c')
 		return error_string(buf, end, "(%p4?)", spec);
@@ -1779,21 +1798,22 @@
 	if (check_pointer(&buf, end, fourcc, spec))
 		return buf;
 
-	val = *fourcc & ~BIT(31);
+	orig = get_unaligned(fourcc);
+	val = orig & ~BIT(31);
 
-	for (i = 0; i < sizeof(*fourcc); i++) {
+	for (i = 0; i < sizeof(u32); i++) {
 		unsigned char c = val >> (i * 8);
 
 		/* Print non-control ASCII characters as-is, dot otherwise */
 		*p++ = isascii(c) && isprint(c) ? c : '.';
 	}
 
-	strcpy(p, *fourcc & BIT(31) ? " big-endian" : " little-endian");
+	strcpy(p, orig & BIT(31) ? " big-endian" : " little-endian");
 	p += strlen(p);
 
 	*p++ = ' ';
 	*p++ = '(';
-	p = special_hex_number(p, output + sizeof(output) - 2, *fourcc, sizeof(u32));
+	p = special_hex_number(p, output + sizeof(output) - 2, orig, sizeof(u32));
 	*p++ = ')';
 	*p = '\0';
 
@@ -2091,15 +2111,20 @@
 
 	/* Loop starting from the root node to the current node. */
 	for (depth = fwnode_count_parents(fwnode); depth >= 0; depth--) {
-		struct fwnode_handle *__fwnode =
-			fwnode_get_nth_parent(fwnode, depth);
+		/*
+		 * Only get a reference for other nodes (i.e. parent nodes).
+		 * fwnode refcount may be 0 here.
+		 */
+		struct fwnode_handle *__fwnode = depth ?
+			fwnode_get_nth_parent(fwnode, depth) : fwnode;
 
 		buf = string(buf, end, fwnode_get_name_prefix(__fwnode),
 			     default_str_spec);
 		buf = string(buf, end, fwnode_get_name(__fwnode),
 			     default_str_spec);
 
-		fwnode_handle_put(__fwnode);
+		if (depth)
+			fwnode_handle_put(__fwnode);
 	}
 
 	return buf;
@@ -2225,10 +2250,6 @@
 	return widen_string(buf, buf - buf_start, end, spec);
 }
 
-/* Disable pointer hashing if requested */
-bool no_hash_pointers __ro_after_init;
-EXPORT_SYMBOL_GPL(no_hash_pointers);
-
 int __init no_hash_pointers_enable(char *str)
 {
 	if (no_hash_pointers)
@@ -2457,7 +2478,7 @@
 	case 'e':
 		/* %pe with a non-ERR_PTR gets treated as plain %p */
 		if (!IS_ERR(ptr))
-			break;
+			return default_pointer(buf, end, ptr, spec);
 		return err_ptr(buf, end, ptr, spec);
 	case 'u':
 	case 'k':
@@ -2467,16 +2488,9 @@
 		default:
 			return error_string(buf, end, "(einval)", spec);
 		}
+	default:
+		return default_pointer(buf, end, ptr, spec);
 	}
-
-	/*
-	 * default is to _not_ leak addresses, so hash before printing,
-	 * unless no_hash_pointers is specified on the command line.
-	 */
-	if (unlikely(no_hash_pointers))
-		return pointer_string(buf, end, ptr, spec);
-	else
-		return ptr_to_id(buf, end, ptr, spec);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/lib/xarray.c
+++ linux-xilinx-zynqmp-5.15.0/lib/xarray.c
@@ -722,6 +722,8 @@
 
 		for (;;) {
 			struct xa_node *node = xas->xa_node;
+			if (node->shift >= shift)
+				break;
 			xas->xa_node = xa_parent_locked(xas->xa, node);
 			xas->xa_offset = node->offset - 1;
 			if (node->offset != 0)
@@ -1079,6 +1081,7 @@
 					xa_mk_node(child));
 			if (xa_is_value(curr))
 				values--;
+			xas_update(xas, child);
 		} else {
 			unsigned int canon = offset - xas->xa_sibs;
 
@@ -1093,6 +1096,7 @@
 	} while (offset-- > xas->xa_offset);
 
 	node->nr_values += values;
+	xas_update(xas, node);
 }
 EXPORT_SYMBOL_GPL(xas_split);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/lib/xz/xz_crc32.c
+++ linux-xilinx-zynqmp-5.15.0/lib/xz/xz_crc32.c
@@ -29,7 +29,7 @@
 
 XZ_EXTERN void xz_crc32_init(void)
 {
-	const uint32_t poly = CRC32_POLY_LE;
+	const uint32_t poly = 0xEDB88320;
 
 	uint32_t i;
 	uint32_t j;
--- linux-xilinx-zynqmp-5.15.0.orig/lib/xz/xz_dec_lzma2.c
+++ linux-xilinx-zynqmp-5.15.0/lib/xz/xz_dec_lzma2.c
@@ -387,7 +387,14 @@
 
 		*left -= copy_size;
 
-		memcpy(dict->buf + dict->pos, b->in + b->in_pos, copy_size);
+		/*
+		 * If doing in-place decompression in single-call mode and the
+		 * uncompressed size of the file is larger than the caller
+		 * thought (i.e. it is invalid input!), the buffers below may
+		 * overlap and cause undefined behavior with memcpy().
+		 * With valid inputs memcpy() would be fine here.
+		 */
+		memmove(dict->buf + dict->pos, b->in + b->in_pos, copy_size);
 		dict->pos += copy_size;
 
 		if (dict->full < dict->pos)
@@ -397,7 +404,11 @@
 			if (dict->pos == dict->end)
 				dict->pos = 0;
 
-			memcpy(b->out + b->out_pos, b->in + b->in_pos,
+			/*
+			 * Like above but for multi-call mode: use memmove()
+			 * to avoid undefined behavior with invalid input.
+			 */
+			memmove(b->out + b->out_pos, b->in + b->in_pos,
 					copy_size);
 		}
 
@@ -421,6 +432,12 @@
 		if (dict->pos == dict->end)
 			dict->pos = 0;
 
+		/*
+		 * These buffers cannot overlap even if doing in-place
+		 * decompression because in multi-call mode dict->buf
+		 * has been allocated by us in this file; it's not
+		 * provided by the caller like in single-call mode.
+		 */
 		memcpy(b->out + b->out_pos, dict->buf + dict->start,
 				copy_size);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/lib/xz/xz_dec_stream.c
+++ linux-xilinx-zynqmp-5.15.0/lib/xz/xz_dec_stream.c
@@ -402,12 +402,12 @@
 	 * we will accept other check types too, but then the check won't
 	 * be verified and a warning (XZ_UNSUPPORTED_CHECK) will be given.
 	 */
+	if (s->temp.buf[HEADER_MAGIC_SIZE + 1] > XZ_CHECK_MAX)
+		return XZ_OPTIONS_ERROR;
+
 	s->check_type = s->temp.buf[HEADER_MAGIC_SIZE + 1];
 
 #ifdef XZ_DEC_ANY_CHECK
-	if (s->check_type > XZ_CHECK_MAX)
-		return XZ_OPTIONS_ERROR;
-
 	if (s->check_type > XZ_CHECK_CRC32)
 		return XZ_UNSUPPORTED_CHECK;
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/lib/xz/xz_private.h
+++ linux-xilinx-zynqmp-5.15.0/lib/xz/xz_private.h
@@ -102,10 +102,6 @@
 #	endif
 #endif
 
-#ifndef CRC32_POLY_LE
-#define CRC32_POLY_LE 0xedb88320
-#endif
-
 /*
  * Allocate memory for LZMA2 decoder. xz_dec_lzma2_reset() must be used
  * before calling xz_dec_lzma2_run().
--- linux-xilinx-zynqmp-5.15.0.orig/meta-files/image-zynqmp.its
+++ linux-xilinx-zynqmp-5.15.0/meta-files/image-zynqmp.its
@@ -0,0 +1,149 @@
+/*
+ * Simple U-Boot uImage source file containing a single kernel, ramdisk and FDT blob
+ */
+
+/dts-v1/;
+
+/ {
+    description = "Simple image with single Linux kernel, ramdisk and FDT blob";
+    #address-cells = <1>;
+
+    images {
+        kernel-1 {
+            description = "Ubuntu kernel";
+            data = /incbin/("../Image.gz-5.15");
+            type = "kernel";
+            arch = "arm64";
+            os = "linux";
+            compression = "gzip";
+            load = <0x00200000>;
+            entry = <0x00200000>;
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        ramdisk-1 {
+            description = "Ubuntu ramdisk";
+            data = /incbin/("../initrd.img");
+            type = "ramdisk";
+            arch = "arm64";
+            os = "linux";
+            compression = "none";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        fdt-zynqmp-smk-k26-revA.dtb {
+            description = "Flattened device tree blob - zynqmp-smk-k26-revA";
+            data = /incbin/("../dtbs/xilinx/zynqmp-smk-k26-revA.dtb");
+            type = "flat_dt";
+            arch = "arm64";
+            compression = "none";
+            load = <0x44000000>;
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        fdt-smk-k26-revA-sck-kr-g-revA.dtb {
+            description = "Flattened device tree blob - smk-k26-revA-sck-kr-g-revA";
+            data = /incbin/("../dtbs/xilinx/smk-k26-revA-sck-kr-g-revA.dtb");
+            type = "flat_dt";
+            arch = "arm64";
+            compression = "none";
+            load = <0x44000000>;
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        fdt-smk-k26-revA-sck-kv-g-revA.dtb {
+            description = "Flattened device tree blob - smk-k26-revA-sck-kv-g-revA";
+            data = /incbin/("../dtbs/xilinx/smk-k26-revA-sck-kv-g-revA.dtb");
+            type = "flat_dt";
+            arch = "arm64";
+            compression = "none";
+            load = <0x44000000>;
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        fdt-smk-k26-revA-sck-kr-g-revB.dtb {
+            description = "Flattened device tree blob - smk-k26-revA-sck-kr-g-revB";
+            data = /incbin/("../dtbs/xilinx/smk-k26-revA-sck-kr-g-revB.dtb");
+            type = "flat_dt";
+            arch = "arm64";
+            compression = "none";
+            load = <0x44000000>;
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        fdt-smk-k26-revA-sck-kv-g-revB.dtb {
+            description = "Flattened device tree blob - smk-k26-revA-sck-kv-g-revB";
+            data = /incbin/("../dtbs/xilinx/smk-k26-revA-sck-kv-g-revB.dtb");
+            type = "flat_dt";
+            arch = "arm64";
+            compression = "none";
+            load = <0x44000000>;
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+    };
+
+    configurations {
+        default = "conf-zynqmp-smk-k26-revA";
+        conf-zynqmp-smk-k26-revA {
+            description = "Boot Ubuntu on kria SOM";
+            kernel = "kernel-1";
+            ramdisk = "ramdisk-1";
+            fdt = "fdt-zynqmp-smk-k26-revA.dtb";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        conf-smk-k26-revA-sck-kr-g-revA {
+            description = "Boot Ubuntu on kria SOM";
+            kernel = "kernel-1";
+            ramdisk = "ramdisk-1";
+            fdt = "fdt-smk-k26-revA-sck-kr-g-revA.dtb";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        conf-smk-k26-revA-sck-kv-g-revA {
+            description = "Boot Ubuntu on kria SOM";
+            kernel = "kernel-1";
+            ramdisk = "ramdisk-1";
+            fdt = "fdt-smk-k26-revA-sck-kv-g-revA.dtb";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        conf-smk-k26-revA-sck-kr-g-revB {
+            description = "Boot Ubuntu on kria SOM";
+            kernel = "kernel-1";
+            ramdisk = "ramdisk-1";
+            fdt = "fdt-smk-k26-revA-sck-kr-g-revB.dtb";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        conf-smk-k26-revA-sck-kv-g-revB {
+            description = "Boot Ubuntu on kria SOM";
+            kernel = "kernel-1";
+            ramdisk = "ramdisk-1";
+            fdt = "fdt-smk-k26-revA-sck-kv-g-revB.dtb";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+        zcu {
+            description = "Boot Ubuntu on zcu board";
+            kernel = "kernel-1";
+            ramdisk = "ramdisk-1";
+            hash-1 {
+                algo = "sha1";
+            };
+        };
+    };
+};
--- linux-xilinx-zynqmp-5.15.0.orig/meta-files/kernel.yaml
+++ linux-xilinx-zynqmp-5.15.0/meta-files/kernel.yaml
@@ -0,0 +1,9 @@
+assets:
+  dtbs:
+    update: true
+    content:
+      - dtbs/
+  img:
+    update: true
+    content:
+      - image.fit
--- linux-xilinx-zynqmp-5.15.0.orig/mm/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/mm/Kconfig
@@ -887,6 +887,9 @@
 config KMAP_LOCAL
 	bool
 
+config KMAP_LOCAL_NON_LINEAR_PTE_ARRAY
+	bool
+
 # struct io_mapping based helper.  Selected by drivers that need them
 config IO_MAPPING
 	bool
--- linux-xilinx-zynqmp-5.15.0.orig/mm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/mm/Makefile
@@ -52,7 +52,7 @@
 			   mm_init.o percpu.o slab_common.o \
 			   compaction.o vmacache.o \
 			   interval_tree.o list_lru.o workingset.o \
-			   debug.o gup.o mmap_lock.o $(mmu-y)
+			   prfile.o debug.o gup.o mmap_lock.o $(mmu-y)
 
 # Give 'page_alloc' its own module-parameter namespace
 page-alloc-y := page_alloc.o
--- linux-xilinx-zynqmp-5.15.0.orig/mm/backing-dev.c
+++ linux-xilinx-zynqmp-5.15.0/mm/backing-dev.c
@@ -229,20 +229,13 @@
 }
 postcore_initcall(bdi_class_init);
 
-static int bdi_init(struct backing_dev_info *bdi);
-
 static int __init default_bdi_init(void)
 {
-	int err;
-
 	bdi_wq = alloc_workqueue("writeback", WQ_MEM_RECLAIM | WQ_UNBOUND |
 				 WQ_SYSFS, 0);
 	if (!bdi_wq)
 		return -ENOMEM;
-
-	err = bdi_init(&noop_backing_dev_info);
-
-	return err;
+	return 0;
 }
 subsys_initcall(default_bdi_init);
 
@@ -265,10 +258,10 @@
 	unsigned long timeout;
 
 	timeout = msecs_to_jiffies(dirty_writeback_interval * 10);
-	spin_lock_bh(&wb->work_lock);
+	spin_lock_irq(&wb->work_lock);
 	if (test_bit(WB_registered, &wb->state))
 		queue_delayed_work(bdi_wq, &wb->dwork, timeout);
-	spin_unlock_bh(&wb->work_lock);
+	spin_unlock_irq(&wb->work_lock);
 }
 
 static void wb_update_bandwidth_workfn(struct work_struct *work)
@@ -344,12 +337,12 @@
 static void wb_shutdown(struct bdi_writeback *wb)
 {
 	/* Make sure nobody queues further work */
-	spin_lock_bh(&wb->work_lock);
+	spin_lock_irq(&wb->work_lock);
 	if (!test_and_clear_bit(WB_registered, &wb->state)) {
-		spin_unlock_bh(&wb->work_lock);
+		spin_unlock_irq(&wb->work_lock);
 		return;
 	}
-	spin_unlock_bh(&wb->work_lock);
+	spin_unlock_irq(&wb->work_lock);
 
 	cgwb_remove_from_bdi_list(wb);
 	/*
@@ -392,6 +385,15 @@
 static void cleanup_offline_cgwbs_workfn(struct work_struct *work);
 static DECLARE_WORK(cleanup_offline_cgwbs_work, cleanup_offline_cgwbs_workfn);
 
+static void cgwb_free_rcu(struct rcu_head *rcu_head)
+{
+	struct bdi_writeback *wb = container_of(rcu_head,
+			struct bdi_writeback, rcu);
+
+	percpu_ref_exit(&wb->refcnt);
+	kfree(wb);
+}
+
 static void cgwb_release_workfn(struct work_struct *work)
 {
 	struct bdi_writeback *wb = container_of(work, struct bdi_writeback,
@@ -414,10 +416,9 @@
 	list_del(&wb->offline_node);
 	spin_unlock_irq(&cgwb_lock);
 
-	percpu_ref_exit(&wb->refcnt);
 	wb_exit(wb);
 	WARN_ON_ONCE(!list_empty(&wb->b_attached));
-	kfree_rcu(wb, rcu);
+	call_rcu(&wb->rcu, cgwb_free_rcu);
 }
 
 static void cgwb_release(struct percpu_ref *refcnt)
@@ -784,7 +785,7 @@
 
 #endif	/* CONFIG_CGROUP_WRITEBACK */
 
-static int bdi_init(struct backing_dev_info *bdi)
+int bdi_init(struct backing_dev_info *bdi)
 {
 	int ret;
 
@@ -947,6 +948,13 @@
 	wb_shutdown(&bdi->wb);
 	cgwb_bdi_unregister(bdi);
 
+	/*
+	 * If this BDI's min ratio has been set, use bdi_set_min_ratio() to
+	 * update the global bdi_min_ratio.
+	 */
+	if (bdi->min_ratio)
+		bdi_set_min_ratio(bdi, 0);
+
 	if (bdi->dev) {
 		bdi_debug_unregister(bdi);
 		device_unregister(bdi->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/bootmem_info.c
+++ linux-xilinx-zynqmp-5.15.0/mm/bootmem_info.c
@@ -12,6 +12,7 @@
 #include <linux/memblock.h>
 #include <linux/bootmem_info.h>
 #include <linux/memory_hotplug.h>
+#include <linux/kmemleak.h>
 
 void get_page_bootmem(unsigned long info, struct page *page, unsigned long type)
 {
@@ -34,6 +35,7 @@
 		ClearPagePrivate(page);
 		set_page_private(page, 0);
 		INIT_LIST_HEAD(&page->lru);
+		kmemleak_free_part(page_to_virt(page), PAGE_SIZE);
 		free_reserved_page(page);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/mm/cma.c
+++ linux-xilinx-zynqmp-5.15.0/mm/cma.c
@@ -37,6 +37,7 @@
 
 struct cma cma_areas[MAX_CMA_AREAS];
 unsigned cma_area_count;
+static DEFINE_MUTEX(cma_mutex);
 
 phys_addr_t cma_get_base(const struct cma *cma)
 {
@@ -168,7 +169,6 @@
 				 struct cma **res_cma)
 {
 	struct cma *cma;
-	phys_addr_t alignment;
 
 	/* Sanity checks */
 	if (cma_area_count == ARRAY_SIZE(cma_areas)) {
@@ -180,14 +180,7 @@
 		return -EINVAL;
 
 	/* ensure minimal alignment required by mm core */
-	alignment = PAGE_SIZE <<
-			max_t(unsigned long, MAX_ORDER - 1, pageblock_order);
-
-	/* alignment should be aligned with order_per_bit */
-	if (!IS_ALIGNED(alignment >> PAGE_SHIFT, 1 << order_per_bit))
-		return -EINVAL;
-
-	if (ALIGN(base, alignment) != base || ALIGN(size, alignment) != size)
+	if (!IS_ALIGNED(base | size, CMA_MIN_ALIGNMENT_BYTES))
 		return -EINVAL;
 
 	/*
@@ -262,14 +255,8 @@
 	if (alignment && !is_power_of_2(alignment))
 		return -EINVAL;
 
-	/*
-	 * Sanitise input arguments.
-	 * Pages both ends in CMA area could be merged into adjacent unmovable
-	 * migratetype page by page allocator's buddy algorithm. In the case,
-	 * you couldn't get a contiguous memory, which is not what we want.
-	 */
-	alignment = max(alignment,  (phys_addr_t)PAGE_SIZE <<
-			  max_t(unsigned long, MAX_ORDER - 1, pageblock_order));
+	/* Sanitise input arguments. */
+	alignment = max_t(phys_addr_t, alignment, CMA_MIN_ALIGNMENT_BYTES);
 	if (fixed && base & (alignment - 1)) {
 		ret = -EINVAL;
 		pr_err("Region at %pa must be aligned to %pa bytes\n",
@@ -471,9 +458,10 @@
 		spin_unlock_irq(&cma->lock);
 
 		pfn = cma->base_pfn + (bitmap_no << cma->order_per_bit);
+		mutex_lock(&cma_mutex);
 		ret = alloc_contig_range(pfn, pfn + count, MIGRATE_CMA,
 				     GFP_KERNEL | (no_warn ? __GFP_NOWARN : 0));
-
+		mutex_unlock(&cma_mutex);
 		if (ret == 0) {
 			page = pfn_to_page(pfn);
 			break;
@@ -501,7 +489,7 @@
 	 */
 	if (page) {
 		for (i = 0; i < count; i++)
-			page_kasan_tag_reset(page + i);
+			page_kasan_tag_reset(nth_page(page, i));
 	}
 
 	if (ret && !no_warn) {
--- linux-xilinx-zynqmp-5.15.0.orig/mm/compaction.c
+++ linux-xilinx-zynqmp-5.15.0/mm/compaction.c
@@ -779,7 +779,7 @@
  * @cc:		Compaction control structure.
  * @low_pfn:	The first PFN to isolate
  * @end_pfn:	The one-past-the-last PFN to isolate, within same pageblock
- * @isolate_mode: Isolation mode to be used.
+ * @mode:	Isolation mode to be used.
  *
  * Isolate all pages that can be migrated from the range specified by
  * [low_pfn, end_pfn). The range is expected to be within same pageblock.
@@ -792,7 +792,7 @@
  */
 static int
 isolate_migratepages_block(struct compact_control *cc, unsigned long low_pfn,
-			unsigned long end_pfn, isolate_mode_t isolate_mode)
+			unsigned long end_pfn, isolate_mode_t mode)
 {
 	pg_data_t *pgdat = cc->zone->zone_pgdat;
 	unsigned long nr_scanned = 0, nr_isolated = 0;
@@ -800,6 +800,7 @@
 	unsigned long flags = 0;
 	struct lruvec *locked = NULL;
 	struct page *page = NULL, *valid_page = NULL;
+	struct address_space *mapping;
 	unsigned long start_pfn = low_pfn;
 	bool skip_on_failure = false;
 	unsigned long next_skip_pfn = 0;
@@ -984,7 +985,7 @@
 					locked = NULL;
 				}
 
-				if (!isolate_movable_page(page, isolate_mode))
+				if (!isolate_movable_page(page, mode))
 					goto isolate_success;
 			}
 
@@ -992,32 +993,68 @@
 		}
 
 		/*
+		 * Be careful not to clear PageLRU until after we're
+		 * sure the page is not being freed elsewhere -- the
+		 * page release code relies on it.
+		 */
+		if (unlikely(!get_page_unless_zero(page)))
+			goto isolate_fail;
+
+		/*
 		 * Migration will fail if an anonymous page is pinned in memory,
 		 * so avoid taking lru_lock and isolating it unnecessarily in an
 		 * admittedly racy check.
 		 */
-		if (!page_mapping(page) &&
-		    page_count(page) > page_mapcount(page))
-			goto isolate_fail;
+		mapping = page_mapping(page);
+		if (!mapping && (page_count(page) - 1) > total_mapcount(page))
+			goto isolate_fail_put;
 
 		/*
 		 * Only allow to migrate anonymous pages in GFP_NOFS context
 		 * because those do not depend on fs locks.
 		 */
-		if (!(cc->gfp_mask & __GFP_FS) && page_mapping(page))
-			goto isolate_fail;
+		if (!(cc->gfp_mask & __GFP_FS) && mapping)
+			goto isolate_fail_put;
+
+		/* Only take pages on LRU: a check now makes later tests safe */
+		if (!PageLRU(page))
+			goto isolate_fail_put;
+
+		/* Compaction might skip unevictable pages but CMA takes them */
+		if (!(mode & ISOLATE_UNEVICTABLE) && PageUnevictable(page))
+			goto isolate_fail_put;
 
 		/*
-		 * Be careful not to clear PageLRU until after we're
-		 * sure the page is not being freed elsewhere -- the
-		 * page release code relies on it.
+		 * To minimise LRU disruption, the caller can indicate with
+		 * ISOLATE_ASYNC_MIGRATE that it only wants to isolate pages
+		 * it will be able to migrate without blocking - clean pages
+		 * for the most part.  PageWriteback would require blocking.
 		 */
-		if (unlikely(!get_page_unless_zero(page)))
-			goto isolate_fail;
-
-		if (!__isolate_lru_page_prepare(page, isolate_mode))
+		if ((mode & ISOLATE_ASYNC_MIGRATE) && PageWriteback(page))
 			goto isolate_fail_put;
 
+		if ((mode & ISOLATE_ASYNC_MIGRATE) && PageDirty(page)) {
+			bool migrate_dirty;
+
+			/*
+			 * Only pages without mappings or that have a
+			 * ->migratepage callback are possible to migrate
+			 * without blocking. However, we can be racing with
+			 * truncation so it's necessary to lock the page
+			 * to stabilise the mapping as truncation holds
+			 * the page lock until after the page is removed
+			 * from the page cache.
+			 */
+			if (!trylock_page(page))
+				goto isolate_fail_put;
+
+			mapping = page_mapping(page);
+			migrate_dirty = !mapping || mapping->a_ops->migratepage;
+			unlock_page(page);
+			if (!migrate_dirty)
+				goto isolate_fail_put;
+		}
+
 		/* Try isolate the page */
 		if (!TestClearPageLRU(page))
 			goto isolate_fail_put;
@@ -1313,7 +1350,7 @@
 }
 
 static void
-fast_isolate_around(struct compact_control *cc, unsigned long pfn, unsigned long nr_isolated)
+fast_isolate_around(struct compact_control *cc, unsigned long pfn)
 {
 	unsigned long start_pfn, end_pfn;
 	struct page *page;
@@ -1334,21 +1371,13 @@
 	if (!page)
 		return;
 
-	/* Scan before */
-	if (start_pfn != pfn) {
-		isolate_freepages_block(cc, &start_pfn, pfn, &cc->freepages, 1, false);
-		if (cc->nr_freepages >= cc->nr_migratepages)
-			return;
-	}
-
-	/* Scan after */
-	start_pfn = pfn + nr_isolated;
-	if (start_pfn < end_pfn)
-		isolate_freepages_block(cc, &start_pfn, end_pfn, &cc->freepages, 1, false);
+	isolate_freepages_block(cc, &start_pfn, end_pfn, &cc->freepages, 1, false);
 
 	/* Skip this pageblock in the future as it's full or nearly full */
 	if (cc->nr_freepages < cc->nr_migratepages)
 		set_pageblock_skip(page);
+
+	return;
 }
 
 /* Search orders in round-robin fashion */
@@ -1524,7 +1553,7 @@
 		return cc->free_pfn;
 
 	low_pfn = page_to_pfn(page);
-	fast_isolate_around(cc, low_pfn, nr_isolated);
+	fast_isolate_around(cc, low_pfn);
 	return low_pfn;
 }
 
@@ -1815,6 +1844,8 @@
 
 				update_fast_start_pfn(cc, free_pfn);
 				pfn = pageblock_start_pfn(free_pfn);
+				if (pfn < cc->zone->zone_start_pfn)
+					pfn = cc->zone->zone_start_pfn;
 				cc->fast_search_fail = 0;
 				found_block = true;
 				set_pageblock_skip(freepage);
@@ -2551,16 +2582,11 @@
 		unsigned int alloc_flags, const struct alloc_context *ac,
 		enum compact_priority prio, struct page **capture)
 {
-	int may_perform_io = gfp_mask & __GFP_IO;
 	struct zoneref *z;
 	struct zone *zone;
 	enum compact_result rc = COMPACT_SKIPPED;
 
-	/*
-	 * Check if the GFP flags allow compaction - GFP_NOIO is really
-	 * tricky context because the migration might require IO
-	 */
-	if (!may_perform_io)
+	if (!gfp_compaction_allowed(gfp_mask))
 		return COMPACT_SKIPPED;
 
 	trace_mm_compaction_try_to_compact_pages(order, gfp_mask, prio);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/damon/core.c
+++ linux-xilinx-zynqmp-5.15.0/mm/damon/core.c
@@ -357,6 +357,15 @@
 	return err;
 }
 
+static void kdamond_usleep(unsigned long usecs)
+{
+	/* See Documentation/timers/timers-howto.rst for the thresholds */
+	if (usecs > 20 * 1000)
+		schedule_timeout_idle(usecs_to_jiffies(usecs));
+	else
+		usleep_idle_range(usecs, usecs + 1);
+}
+
 /*
  * __damon_stop() - Stops monitoring of given context.
  * @ctx:	monitoring context
@@ -370,8 +379,7 @@
 		ctx->kdamond_stop = true;
 		mutex_unlock(&ctx->kdamond_lock);
 		while (damon_kdamond_running(ctx))
-			usleep_range(ctx->sample_interval,
-					ctx->sample_interval * 2);
+			kdamond_usleep(ctx->sample_interval);
 		return 0;
 	}
 	mutex_unlock(&ctx->kdamond_lock);
@@ -499,14 +507,31 @@
  * access frequencies are similar.  This is for minimizing the monitoring
  * overhead under the dynamically changeable access pattern.  If a merge was
  * unnecessarily made, later 'kdamond_split_regions()' will revert it.
+ *
+ * The total number of regions could be higher than the user-defined limit,
+ * max_nr_regions for some cases.  For example, the user can update
+ * max_nr_regions to a number that lower than the current number of regions
+ * while DAMON is running.  For such a case, repeat merging until the limit is
+ * met while increasing @threshold up to possible maximum level.
  */
 static void kdamond_merge_regions(struct damon_ctx *c, unsigned int threshold,
 				  unsigned long sz_limit)
 {
 	struct damon_target *t;
+	unsigned int nr_regions;
+	unsigned int max_thres;
 
-	damon_for_each_target(t, c)
-		damon_merge_regions_of(t, threshold, sz_limit);
+	max_thres = c->aggr_interval /
+		(c->sample_interval ?  c->sample_interval : 1);
+	do {
+		nr_regions = 0;
+		damon_for_each_target(t, c) {
+			damon_merge_regions_of(t, threshold, sz_limit);
+			nr_regions += damon_nr_regions(t);
+		}
+		threshold = max(1, threshold * 2);
+	} while (nr_regions > c->max_nr_regions &&
+			threshold / 2 < max_thres);
 }
 
 /*
@@ -670,7 +695,7 @@
 				ctx->callback.after_sampling(ctx))
 			set_kdamond_stop(ctx);
 
-		usleep_range(ctx->sample_interval, ctx->sample_interval + 1);
+		kdamond_usleep(ctx->sample_interval);
 
 		if (ctx->primitive.check_accesses)
 			max_nr_accesses = ctx->primitive.check_accesses(ctx);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/damon/dbgfs.c
+++ linux-xilinx-zynqmp-5.15.0/mm/damon/dbgfs.c
@@ -32,7 +32,7 @@
 	if (*ppos)
 		return ERR_PTR(-EINVAL);
 
-	kbuf = kmalloc(count + 1, GFP_KERNEL);
+	kbuf = kmalloc(count + 1, GFP_KERNEL | __GFP_NOWARN);
 	if (!kbuf)
 		return ERR_PTR(-ENOMEM);
 
@@ -185,6 +185,7 @@
 		const char __user *buf, size_t count, loff_t *ppos)
 {
 	struct damon_ctx *ctx = file->private_data;
+	struct damon_target *t, *next_t;
 	char *kbuf, *nrs;
 	unsigned long *targets;
 	ssize_t nr_targets;
@@ -224,6 +225,13 @@
 		goto unlock_out;
 	}
 
+	/* remove previously set targets */
+	damon_for_each_target_safe(t, next_t, ctx) {
+		if (targetid_is_pid(ctx))
+			put_pid((struct pid *)t->id);
+		damon_destroy_target(t);
+	}
+
 	err = damon_set_targets(ctx, targets, nr_targets);
 	if (err) {
 		if (targetid_is_pid(ctx))
@@ -247,7 +255,7 @@
 	char *kbuf;
 	ssize_t len;
 
-	kbuf = kmalloc(count, GFP_KERNEL);
+	kbuf = kmalloc(count, GFP_KERNEL | __GFP_NOWARN);
 	if (!kbuf)
 		return -ENOMEM;
 
@@ -309,10 +317,12 @@
 	if (!targetid_is_pid(ctx))
 		return 0;
 
+	mutex_lock(&ctx->kdamond_lock);
 	damon_for_each_target_safe(t, next, ctx) {
 		put_pid((struct pid *)t->id);
 		damon_destroy_target(t);
 	}
+	mutex_unlock(&ctx->kdamond_lock);
 	return 0;
 }
 
@@ -366,6 +376,9 @@
 		return -ENOENT;
 
 	new_dir = debugfs_create_dir(name, root);
+	/* Below check is required for a potential duplicated name case */
+	if (IS_ERR(new_dir))
+		return PTR_ERR(new_dir);
 	dbgfs_dirs[dbgfs_nr_ctxs] = new_dir;
 
 	new_ctx = dbgfs_new_ctx();
@@ -428,8 +441,10 @@
 static int dbgfs_rm_context(char *name)
 {
 	struct dentry *root, *dir, **new_dirs;
+	struct inode *inode;
 	struct damon_ctx **new_ctxs;
 	int i, j;
+	int ret = 0;
 
 	if (damon_nr_running_ctxs())
 		return -EBUSY;
@@ -442,16 +457,24 @@
 	if (!dir)
 		return -ENOENT;
 
+	inode = d_inode(dir);
+	if (!S_ISDIR(inode->i_mode)) {
+		ret = -EINVAL;
+		goto out_dput;
+	}
+
 	new_dirs = kmalloc_array(dbgfs_nr_ctxs - 1, sizeof(*dbgfs_dirs),
 			GFP_KERNEL);
-	if (!new_dirs)
-		return -ENOMEM;
+	if (!new_dirs) {
+		ret = -ENOMEM;
+		goto out_dput;
+	}
 
 	new_ctxs = kmalloc_array(dbgfs_nr_ctxs - 1, sizeof(*dbgfs_ctxs),
 			GFP_KERNEL);
 	if (!new_ctxs) {
-		kfree(new_dirs);
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto out_new_dirs;
 	}
 
 	for (i = 0, j = 0; i < dbgfs_nr_ctxs; i++) {
@@ -471,7 +494,13 @@
 	dbgfs_ctxs = new_ctxs;
 	dbgfs_nr_ctxs--;
 
-	return 0;
+	goto out_dput;
+
+out_new_dirs:
+	kfree(new_dirs);
+out_dput:
+	dput(dir);
+	return ret;
 }
 
 static ssize_t dbgfs_rm_context_write(struct file *file,
@@ -538,12 +567,14 @@
 		return -EINVAL;
 	}
 
+	mutex_lock(&damon_dbgfs_lock);
 	if (!strncmp(kbuf, "on", count))
 		err = damon_start(dbgfs_ctxs, dbgfs_nr_ctxs);
 	else if (!strncmp(kbuf, "off", count))
 		err = damon_stop(dbgfs_ctxs, dbgfs_nr_ctxs);
 	else
 		err = -EINVAL;
+	mutex_unlock(&damon_dbgfs_lock);
 
 	if (err)
 		ret = err;
@@ -596,15 +627,16 @@
 
 static int __init damon_dbgfs_init(void)
 {
-	int rc;
+	int rc = -ENOMEM;
 
+	mutex_lock(&damon_dbgfs_lock);
 	dbgfs_ctxs = kmalloc(sizeof(*dbgfs_ctxs), GFP_KERNEL);
 	if (!dbgfs_ctxs)
-		return -ENOMEM;
+		goto out;
 	dbgfs_ctxs[0] = dbgfs_new_ctx();
 	if (!dbgfs_ctxs[0]) {
 		kfree(dbgfs_ctxs);
-		return -ENOMEM;
+		goto out;
 	}
 	dbgfs_nr_ctxs = 1;
 
@@ -615,6 +647,8 @@
 		pr_err("%s: dbgfs init failed\n", __func__);
 	}
 
+out:
+	mutex_unlock(&damon_dbgfs_lock);
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/damon/vaddr-test.h
+++ linux-xilinx-zynqmp-5.15.0/mm/damon/vaddr-test.h
@@ -252,59 +252,63 @@
 			new_three_regions, expected, ARRAY_SIZE(expected));
 }
 
-static void damon_test_split_evenly(struct kunit *test)
+static void damon_test_split_evenly_fail(struct kunit *test,
+		unsigned long start, unsigned long end, unsigned int nr_pieces)
 {
-	struct damon_ctx *c = damon_new_ctx();
-	struct damon_target *t;
-	struct damon_region *r;
-	unsigned long i;
-
-	KUNIT_EXPECT_EQ(test, damon_va_evenly_split_region(NULL, NULL, 5),
-			-EINVAL);
-
-	t = damon_new_target(42);
-	r = damon_new_region(0, 100);
-	KUNIT_EXPECT_EQ(test, damon_va_evenly_split_region(t, r, 0), -EINVAL);
+	struct damon_target *t = damon_new_target(42);
+	struct damon_region *r = damon_new_region(start, end);
 
 	damon_add_region(r, t);
-	KUNIT_EXPECT_EQ(test, damon_va_evenly_split_region(t, r, 10), 0);
-	KUNIT_EXPECT_EQ(test, damon_nr_regions(t), 10u);
+	KUNIT_EXPECT_EQ(test,
+			damon_va_evenly_split_region(t, r, nr_pieces), -EINVAL);
+	KUNIT_EXPECT_EQ(test, damon_nr_regions(t), 1u);
 
-	i = 0;
 	damon_for_each_region(r, t) {
-		KUNIT_EXPECT_EQ(test, r->ar.start, i++ * 10);
-		KUNIT_EXPECT_EQ(test, r->ar.end, i * 10);
+		KUNIT_EXPECT_EQ(test, r->ar.start, start);
+		KUNIT_EXPECT_EQ(test, r->ar.end, end);
 	}
+
 	damon_free_target(t);
+}
+
+static void damon_test_split_evenly_succ(struct kunit *test,
+	unsigned long start, unsigned long end, unsigned int nr_pieces)
+{
+	struct damon_target *t = damon_new_target(42);
+	struct damon_region *r = damon_new_region(start, end);
+	unsigned long expected_width = (end - start) / nr_pieces;
+	unsigned long i = 0;
 
-	t = damon_new_target(42);
-	r = damon_new_region(5, 59);
 	damon_add_region(r, t);
-	KUNIT_EXPECT_EQ(test, damon_va_evenly_split_region(t, r, 5), 0);
-	KUNIT_EXPECT_EQ(test, damon_nr_regions(t), 5u);
+	KUNIT_EXPECT_EQ(test,
+			damon_va_evenly_split_region(t, r, nr_pieces), 0);
+	KUNIT_EXPECT_EQ(test, damon_nr_regions(t), nr_pieces);
 
-	i = 0;
 	damon_for_each_region(r, t) {
-		if (i == 4)
+		if (i == nr_pieces - 1)
 			break;
-		KUNIT_EXPECT_EQ(test, r->ar.start, 5 + 10 * i++);
-		KUNIT_EXPECT_EQ(test, r->ar.end, 5 + 10 * i);
+		KUNIT_EXPECT_EQ(test,
+				r->ar.start, start + i++ * expected_width);
+		KUNIT_EXPECT_EQ(test, r->ar.end, start + i * expected_width);
 	}
-	KUNIT_EXPECT_EQ(test, r->ar.start, 5 + 10 * i);
-	KUNIT_EXPECT_EQ(test, r->ar.end, 59ul);
+	KUNIT_EXPECT_EQ(test, r->ar.start, start + i * expected_width);
+	KUNIT_EXPECT_EQ(test, r->ar.end, end);
 	damon_free_target(t);
+}
 
-	t = damon_new_target(42);
-	r = damon_new_region(5, 6);
-	damon_add_region(r, t);
-	KUNIT_EXPECT_EQ(test, damon_va_evenly_split_region(t, r, 2), -EINVAL);
-	KUNIT_EXPECT_EQ(test, damon_nr_regions(t), 1u);
+static void damon_test_split_evenly(struct kunit *test)
+{
+	struct damon_ctx *c = damon_new_ctx();
+
+	KUNIT_EXPECT_EQ(test, damon_va_evenly_split_region(NULL, NULL, 5),
+			-EINVAL);
+
+	damon_test_split_evenly_fail(test, 0, 100, 0);
+	damon_test_split_evenly_succ(test, 0, 100, 10);
+	damon_test_split_evenly_succ(test, 5, 59, 5);
+	damon_test_split_evenly_succ(test, 0, 3, 2);
+	damon_test_split_evenly_fail(test, 5, 6, 2);
 
-	damon_for_each_region(r, t) {
-		KUNIT_EXPECT_EQ(test, r->ar.start, 5ul);
-		KUNIT_EXPECT_EQ(test, r->ar.end, 6ul);
-	}
-	damon_free_target(t);
 	damon_destroy_ctx(c);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/damon/vaddr.c
+++ linux-xilinx-zynqmp-5.15.0/mm/damon/vaddr.c
@@ -69,6 +69,7 @@
 	unsigned long sz_orig, sz_piece, orig_end;
 	struct damon_region *n = NULL, *next;
 	unsigned long start;
+	unsigned int i;
 
 	if (!r || !nr_pieces)
 		return -EINVAL;
@@ -82,8 +83,7 @@
 
 	r->ar.end = r->ar.start + sz_piece;
 	next = damon_next_region(r);
-	for (start = r->ar.end; start + sz_piece <= orig_end;
-			start += sz_piece) {
+	for (start = r->ar.end, i = 1; i < nr_pieces; start += sz_piece, i++) {
 		n = damon_new_region(start, start + sz_piece);
 		if (!n)
 			return -ENOMEM;
@@ -393,7 +393,7 @@
 	return page;
 }
 
-static void damon_ptep_mkold(pte_t *pte, struct mm_struct *mm,
+static void damon_ptep_mkold(pte_t *pte, struct vm_area_struct *vma,
 			     unsigned long addr)
 {
 	bool referenced = false;
@@ -402,13 +402,11 @@
 	if (!page)
 		return;
 
-	if (pte_young(*pte)) {
+	if (ptep_test_and_clear_young(vma, addr, pte))
 		referenced = true;
-		*pte = pte_mkold(*pte);
-	}
 
 #ifdef CONFIG_MMU_NOTIFIER
-	if (mmu_notifier_clear_young(mm, addr, addr + PAGE_SIZE))
+	if (mmu_notifier_clear_young(vma->vm_mm, addr, addr + PAGE_SIZE))
 		referenced = true;
 #endif /* CONFIG_MMU_NOTIFIER */
 
@@ -419,7 +417,7 @@
 	put_page(page);
 }
 
-static void damon_pmdp_mkold(pmd_t *pmd, struct mm_struct *mm,
+static void damon_pmdp_mkold(pmd_t *pmd, struct vm_area_struct *vma,
 			     unsigned long addr)
 {
 #ifdef CONFIG_TRANSPARENT_HUGEPAGE
@@ -429,13 +427,11 @@
 	if (!page)
 		return;
 
-	if (pmd_young(*pmd)) {
+	if (pmdp_test_and_clear_young(vma, addr, pmd))
 		referenced = true;
-		*pmd = pmd_mkold(*pmd);
-	}
 
 #ifdef CONFIG_MMU_NOTIFIER
-	if (mmu_notifier_clear_young(mm, addr,
+	if (mmu_notifier_clear_young(vma->vm_mm, addr,
 				addr + ((1UL) << HPAGE_PMD_SHIFT)))
 		referenced = true;
 #endif /* CONFIG_MMU_NOTIFIER */
@@ -456,8 +452,13 @@
 
 	if (pmd_huge(*pmd)) {
 		ptl = pmd_lock(walk->mm, pmd);
+		if (!pmd_present(*pmd)) {
+			spin_unlock(ptl);
+			return 0;
+		}
+
 		if (pmd_huge(*pmd)) {
-			damon_pmdp_mkold(pmd, walk->mm, addr);
+			damon_pmdp_mkold(pmd, walk->vma, addr);
 			spin_unlock(ptl);
 			return 0;
 		}
@@ -469,7 +470,7 @@
 	pte = pte_offset_map_lock(walk->mm, pmd, addr, &ptl);
 	if (!pte_present(*pte))
 		goto out;
-	damon_ptep_mkold(pte, walk->mm, addr);
+	damon_ptep_mkold(pte, walk->vma, addr);
 out:
 	pte_unmap_unlock(pte, ptl);
 	return 0;
@@ -530,6 +531,11 @@
 #ifdef CONFIG_TRANSPARENT_HUGEPAGE
 	if (pmd_huge(*pmd)) {
 		ptl = pmd_lock(walk->mm, pmd);
+		if (!pmd_present(*pmd)) {
+			spin_unlock(ptl);
+			return 0;
+		}
+
 		if (!pmd_huge(*pmd)) {
 			spin_unlock(ptl);
 			goto regular_page;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/debug_vm_pgtable.c
+++ linux-xilinx-zynqmp-5.15.0/mm/debug_vm_pgtable.c
@@ -171,6 +171,8 @@
 	ptep_test_and_clear_young(args->vma, args->vaddr, args->ptep);
 	pte = ptep_get(args->ptep);
 	WARN_ON(pte_young(pte));
+
+	ptep_get_and_clear_full(args->mm, args->vaddr, args->ptep, 1);
 }
 
 static void __init pte_savedwrite_tests(struct pgtable_debug_args *args)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/filemap.c
+++ linux-xilinx-zynqmp-5.15.0/mm/filemap.c
@@ -90,7 +90,7 @@
  *      ->lock_page		(filemap_fault, access_process_vm)
  *
  *  ->i_rwsem			(generic_perform_write)
- *    ->mmap_lock		(fault_in_pages_readable->do_page_fault)
+ *    ->mmap_lock		(fault_in_readable->do_page_fault)
  *
  *  bdi->wb.list_lock
  *    sb_lock			(fs/fs-writeback.c)
@@ -2090,10 +2090,13 @@
 
 	rcu_read_lock();
 	while ((page = find_get_entry(&xas, end, XA_PRESENT))) {
+		unsigned long next_idx = xas.xa_index + 1;
+
 		if (!xa_is_value(page)) {
+			if (PageTransHuge(page))
+				next_idx = page->index + thp_nr_pages(page);
 			if (page->index < start)
 				goto put;
-			VM_BUG_ON_PAGE(page->index != xas.xa_index, page);
 			if (page->index + thp_nr_pages(page) - 1 > end)
 				goto put;
 			if (!trylock_page(page))
@@ -2112,13 +2115,11 @@
 put:
 		put_page(page);
 next:
-		if (!xa_is_value(page) && PageTransHuge(page)) {
-			unsigned int nr_pages = thp_nr_pages(page);
-
+		if (next_idx != xas.xa_index + 1) {
 			/* Final THP may cross MAX_LFS_FILESIZE on 32-bit */
-			xas_set(&xas, page->index + nr_pages);
-			if (xas.xa_index < nr_pages)
+			if (next_idx < xas.xa_index)
 				break;
+			xas_set(&xas, next_idx);
 		}
 	}
 	rcu_read_unlock();
@@ -2355,8 +2356,12 @@
 			break;
 		if (PageReadahead(head))
 			break;
-		xas.xa_index = head->index + thp_nr_pages(head) - 1;
-		xas.xa_offset = (xas.xa_index >> xas.xa_shift) & XA_CHUNK_MASK;
+		if (PageHead(head)) {
+			xas_set(&xas, head->index + thp_nr_pages(head));
+			/* Handle wrap correctly */
+			if (xas.xa_index - 1 >= max)
+				break;
+		}
 		continue;
 put_page:
 		put_page(head);
@@ -2533,18 +2538,19 @@
 	struct page *page;
 	int err = 0;
 
+	/* "last_index" is the index of the page beyond the end of the read */
 	last_index = DIV_ROUND_UP(iocb->ki_pos + iter->count, PAGE_SIZE);
 retry:
 	if (fatal_signal_pending(current))
 		return -EINTR;
 
-	filemap_get_read_batch(mapping, index, last_index, pvec);
+	filemap_get_read_batch(mapping, index, last_index - 1, pvec);
 	if (!pagevec_count(pvec)) {
 		if (iocb->ki_flags & IOCB_NOIO)
 			return -EAGAIN;
 		page_cache_sync_readahead(mapping, ra, filp, index,
 				last_index - index);
-		filemap_get_read_batch(mapping, index, last_index, pvec);
+		filemap_get_read_batch(mapping, index, last_index - 1, pvec);
 	}
 	if (!pagevec_count(pvec)) {
 		if (iocb->ki_flags & (IOCB_NOWAIT | IOCB_WAITQ))
@@ -2643,6 +2649,15 @@
 		end_offset = min_t(loff_t, isize, iocb->ki_pos + iter->count);
 
 		/*
+		 * Pairs with a barrier in
+		 * block_write_end()->mark_buffer_dirty() or other page
+		 * dirtying routines like iomap_write_end() to ensure
+		 * changes to page contents are visible before we see
+		 * increased inode size.
+		 */
+		smp_rmb();
+
+		/*
 		 * Once we start copying data, we don't want to be touching any
 		 * cachelines that might be contended:
 		 */
@@ -2803,7 +2818,7 @@
 	do {
 		if (ops->is_partially_uptodate(page, offset, bsz) == seek_data)
 			break;
-		start = (start + bsz) & ~(bsz - 1);
+		start = (start + bsz) & ~((u64)bsz - 1);
 		offset += bsz;
 	} while (offset < thp_size(page));
 unlock:
@@ -3203,7 +3218,7 @@
 	    }
 	}
 
-	if (pmd_none(*vmf->pmd)) {
+	if (pmd_none(*vmf->pmd) && vmf->prealloc_pte) {
 		vmf->ptl = pmd_lock(mm, vmf->pmd);
 		if (likely(pmd_none(*vmf->pmd))) {
 			mm_inc_nr_ptes(mm);
@@ -3350,7 +3365,7 @@
 	vm_fault_t ret = VM_FAULT_LOCKED;
 
 	sb_start_pagefault(mapping->host->i_sb);
-	file_update_time(vmf->vma->vm_file);
+	vma_file_update_time(vmf->vma);
 	lock_page(page);
 	if (page->mapping != mapping) {
 		unlock_page(page);
@@ -3744,7 +3759,7 @@
 		unsigned long offset;	/* Offset into pagecache page */
 		unsigned long bytes;	/* Bytes to write to page */
 		size_t copied;		/* Bytes copied from user */
-		void *fsdata;
+		void *fsdata = NULL;
 
 		offset = (pos & (PAGE_SIZE - 1));
 		bytes = min_t(unsigned long, PAGE_SIZE - offset,
@@ -3757,7 +3772,7 @@
 		 * same page as we're writing to, without it being marked
 		 * up-to-date.
 		 */
-		if (unlikely(iov_iter_fault_in_readable(i, bytes))) {
+		if (unlikely(fault_in_iov_iter_readable(i, bytes))) {
 			status = -EFAULT;
 			break;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/mm/gup.c
+++ linux-xilinx-zynqmp-5.15.0/mm/gup.c
@@ -124,8 +124,8 @@
  * considered failure, and furthermore, a likely bug in the caller, so a warning
  * is also emitted.
  */
-struct page *try_grab_compound_head(struct page *page,
-				    int refs, unsigned int flags)
+__maybe_unused struct page *try_grab_compound_head(struct page *page,
+						   int refs, unsigned int flags)
 {
 	if (flags & FOLL_GET)
 		return try_get_compound_head(page, refs);
@@ -208,10 +208,35 @@
  */
 bool __must_check try_grab_page(struct page *page, unsigned int flags)
 {
-	if (!(flags & (FOLL_GET | FOLL_PIN)))
-		return true;
+	WARN_ON_ONCE((flags & (FOLL_GET | FOLL_PIN)) == (FOLL_GET | FOLL_PIN));
 
-	return try_grab_compound_head(page, 1, flags);
+	if (flags & FOLL_GET)
+		return try_get_page(page);
+	else if (flags & FOLL_PIN) {
+		int refs = 1;
+
+		page = compound_head(page);
+
+		if (WARN_ON_ONCE(page_ref_count(page) <= 0))
+			return false;
+
+		if (hpage_pincount_available(page))
+			hpage_pincount_add(page, 1);
+		else
+			refs = GUP_PIN_COUNTING_BIAS;
+
+		/*
+		 * Similar to try_grab_compound_head(): even if using the
+		 * hpage_pincount_add/_sub() routines, be sure to
+		 * *also* increment the normal page refcount field at least
+		 * once, so that the page really is pinned.
+		 */
+		page_ref_add(page, refs);
+
+		mod_node_page_state(page_pgdat(page), NR_FOLL_PIN_ACQUIRED, 1);
+	}
+
+	return true;
 }
 
 /**
@@ -440,7 +465,7 @@
 		pte_t *pte, unsigned int flags)
 {
 	/* No page to get reference */
-	if (flags & FOLL_GET)
+	if (flags & (FOLL_GET | FOLL_PIN))
 		return -EFAULT;
 
 	if (flags & FOLL_TOUCH) {
@@ -484,6 +509,18 @@
 	if (WARN_ON_ONCE((flags & (FOLL_PIN | FOLL_GET)) ==
 			 (FOLL_PIN | FOLL_GET)))
 		return ERR_PTR(-EINVAL);
+
+	/*
+	 * Considering PTE level hugetlb, like continuous-PTE hugetlb on
+	 * ARM64 architecture.
+	 */
+	if (is_vm_hugetlb_page(vma)) {
+		page = follow_huge_pmd_pte(vma, address, flags);
+		if (page)
+			return page;
+		return no_page_table(vma, flags);
+	}
+
 retry:
 	if (unlikely(pmd_bad(*pmd)))
 		return no_page_table(vma, flags);
@@ -627,7 +664,7 @@
 	if (pmd_none(pmdval))
 		return no_page_table(vma, flags);
 	if (pmd_huge(pmdval) && is_vm_hugetlb_page(vma)) {
-		page = follow_huge_pmd(mm, address, pmd, flags);
+		page = follow_huge_pmd_pte(vma, address, flags);
 		if (page)
 			return page;
 		return no_page_table(vma, flags);
@@ -918,6 +955,8 @@
 	/* mlock all present pages, but do not fault in new pages */
 	if ((*flags & (FOLL_POPULATE | FOLL_MLOCK)) == FOLL_MLOCK)
 		return -ENOENT;
+	if (*flags & FOLL_NOFAULT)
+		return -EFAULT;
 	if (*flags & FOLL_WRITE)
 		fault_flags |= FAULT_FLAG_WRITE;
 	if (*flags & FOLL_REMOTE)
@@ -1657,6 +1696,122 @@
 #endif /* !CONFIG_MMU */
 
 /**
+ * fault_in_writeable - fault in userspace address range for writing
+ * @uaddr: start of address range
+ * @size: size of address range
+ *
+ * Returns the number of bytes not faulted in (like copy_to_user() and
+ * copy_from_user()).
+ */
+size_t fault_in_writeable(char __user *uaddr, size_t size)
+{
+	char __user *start = uaddr, *end;
+
+	if (unlikely(size == 0))
+		return 0;
+	if (!PAGE_ALIGNED(uaddr)) {
+		if (unlikely(__put_user(0, uaddr) != 0))
+			return size;
+		uaddr = (char __user *)PAGE_ALIGN((unsigned long)uaddr);
+	}
+	end = (char __user *)PAGE_ALIGN((unsigned long)start + size);
+	if (unlikely(end < start))
+		end = NULL;
+	while (uaddr != end) {
+		if (unlikely(__put_user(0, uaddr) != 0))
+			goto out;
+		uaddr += PAGE_SIZE;
+	}
+
+out:
+	if (size > uaddr - start)
+		return size - (uaddr - start);
+	return 0;
+}
+EXPORT_SYMBOL(fault_in_writeable);
+
+/*
+ * fault_in_safe_writeable - fault in an address range for writing
+ * @uaddr: start of address range
+ * @size: length of address range
+ *
+ * Faults in an address range for writing.  This is primarily useful when we
+ * already know that some or all of the pages in the address range aren't in
+ * memory.
+ *
+ * Unlike fault_in_writeable(), this function is non-destructive.
+ *
+ * Note that we don't pin or otherwise hold the pages referenced that we fault
+ * in.  There's no guarantee that they'll stay in memory for any duration of
+ * time.
+ *
+ * Returns the number of bytes not faulted in, like copy_to_user() and
+ * copy_from_user().
+ */
+size_t fault_in_safe_writeable(const char __user *uaddr, size_t size)
+{
+	unsigned long start = (unsigned long)uaddr, end;
+	struct mm_struct *mm = current->mm;
+	bool unlocked = false;
+
+	if (unlikely(size == 0))
+		return 0;
+	end = PAGE_ALIGN(start + size);
+	if (end < start)
+		end = 0;
+
+	mmap_read_lock(mm);
+	do {
+		if (fixup_user_fault(mm, start, FAULT_FLAG_WRITE, &unlocked))
+			break;
+		start = (start + PAGE_SIZE) & PAGE_MASK;
+	} while (start != end);
+	mmap_read_unlock(mm);
+
+	if (size > (unsigned long)uaddr - start)
+		return size - ((unsigned long)uaddr - start);
+	return 0;
+}
+EXPORT_SYMBOL(fault_in_safe_writeable);
+
+/**
+ * fault_in_readable - fault in userspace address range for reading
+ * @uaddr: start of user address range
+ * @size: size of user address range
+ *
+ * Returns the number of bytes not faulted in (like copy_to_user() and
+ * copy_from_user()).
+ */
+size_t fault_in_readable(const char __user *uaddr, size_t size)
+{
+	const char __user *start = uaddr, *end;
+	volatile char c;
+
+	if (unlikely(size == 0))
+		return 0;
+	if (!PAGE_ALIGNED(uaddr)) {
+		if (unlikely(__get_user(c, uaddr) != 0))
+			return size;
+		uaddr = (const char __user *)PAGE_ALIGN((unsigned long)uaddr);
+	}
+	end = (const char __user *)PAGE_ALIGN((unsigned long)start + size);
+	if (unlikely(end < start))
+		end = NULL;
+	while (uaddr != end) {
+		if (unlikely(__get_user(c, uaddr) != 0))
+			goto out;
+		uaddr += PAGE_SIZE;
+	}
+
+out:
+	(void)c;
+	if (size > uaddr - start)
+		return size - (uaddr - start);
+	return 0;
+}
+EXPORT_SYMBOL(fault_in_readable);
+
+/**
  * get_dump_page() - pin user page in memory while writing it to core dump
  * @addr: user address
  *
@@ -1722,7 +1877,7 @@
 		 */
 		if (!is_pinnable_page(head)) {
 			if (PageHuge(head)) {
-				if (!isolate_huge_page(head, &movable_page_list))
+				if (isolate_hugetlb(head, &movable_page_list))
 					isolation_error_count++;
 			} else {
 				if (!PageLRU(head) && drain_allow) {
@@ -2123,8 +2278,28 @@
 }
 
 #ifdef CONFIG_ARCH_HAS_PTE_SPECIAL
-static int gup_pte_range(pmd_t pmd, unsigned long addr, unsigned long end,
-			 unsigned int flags, struct page **pages, int *nr)
+/*
+ * Fast-gup relies on pte change detection to avoid concurrent pgtable
+ * operations.
+ *
+ * To pin the page, fast-gup needs to do below in order:
+ * (1) pin the page (by prefetching pte), then (2) check pte not changed.
+ *
+ * For the rest of pgtable operations where pgtable updates can be racy
+ * with fast-gup, we need to do (1) clear pte, then (2) check whether page
+ * is pinned.
+ *
+ * Above will work for all pte-level operations, including THP split.
+ *
+ * For THP collapse, it's a bit more complicated because fast-gup may be
+ * walking a pgtable page that is being freed (pte is still valid but pmd
+ * can be cleared already).  To avoid race in such condition, we need to
+ * also check pmd here to make sure pmd doesn't change (corresponds to
+ * pmdp_collapse_flush() in the THP collapse code path).
+ */
+static int gup_pte_range(pmd_t pmd, pmd_t *pmdp, unsigned long addr,
+			 unsigned long end, unsigned int flags,
+			 struct page **pages, int *nr)
 {
 	struct dev_pagemap *pgmap = NULL;
 	int nr_start = *nr, ret = 0;
@@ -2169,7 +2344,8 @@
 			goto pte_unmap;
 		}
 
-		if (unlikely(pte_val(pte) != pte_val(*ptep))) {
+		if (unlikely(pmd_val(pmd) != pmd_val(*pmdp)) ||
+		    unlikely(pte_val(pte) != pte_val(*ptep))) {
 			put_compound_head(head, 1, flags);
 			goto pte_unmap;
 		}
@@ -2214,8 +2390,9 @@
  * get_user_pages_fast_only implementation that can pin pages. Thus it's still
  * useful to have gup_huge_pmd even if we can't operate on ptes.
  */
-static int gup_pte_range(pmd_t pmd, unsigned long addr, unsigned long end,
-			 unsigned int flags, struct page **pages, int *nr)
+static int gup_pte_range(pmd_t pmd, pmd_t *pmdp, unsigned long addr,
+			 unsigned long end, unsigned int flags,
+			 struct page **pages, int *nr)
 {
 	return 0;
 }
@@ -2524,7 +2701,7 @@
 			if (!gup_huge_pd(__hugepd(pmd_val(pmd)), addr,
 					 PMD_SHIFT, next, flags, pages, nr))
 				return 0;
-		} else if (!gup_pte_range(pmd, addr, next, flags, pages, nr))
+		} else if (!gup_pte_range(pmd, pmdp, addr, next, flags, pages, nr))
 			return 0;
 	} while (pmdp++, addr = next, addr != end);
 
@@ -2544,7 +2721,7 @@
 		next = pud_addr_end(addr, end);
 		if (unlikely(!pud_present(pud)))
 			return 0;
-		if (unlikely(pud_huge(pud))) {
+		if (unlikely(pud_huge(pud) || pud_devmap(pud))) {
 			if (!gup_huge_pud(pud, pudp, addr, next, flags,
 					  pages, nr))
 				return 0;
@@ -2708,7 +2885,7 @@
 
 	if (WARN_ON_ONCE(gup_flags & ~(FOLL_WRITE | FOLL_LONGTERM |
 				       FOLL_FORCE | FOLL_PIN | FOLL_GET |
-				       FOLL_FAST_ONLY)))
+				       FOLL_FAST_ONLY | FOLL_NOFAULT)))
 		return -EINVAL;
 
 	if (gup_flags & FOLL_PIN)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/highmem.c
+++ linux-xilinx-zynqmp-5.15.0/mm/highmem.c
@@ -504,16 +504,22 @@
 
 static pte_t *__kmap_pte;
 
-static pte_t *kmap_get_pte(void)
+static pte_t *kmap_get_pte(unsigned long vaddr, int idx)
 {
+	if (IS_ENABLED(CONFIG_KMAP_LOCAL_NON_LINEAR_PTE_ARRAY))
+		/*
+		 * Set by the arch if __kmap_pte[-idx] does not produce
+		 * the correct entry.
+		 */
+		return virt_to_kpte(vaddr);
 	if (!__kmap_pte)
 		__kmap_pte = virt_to_kpte(__fix_to_virt(FIX_KMAP_BEGIN));
-	return __kmap_pte;
+	return &__kmap_pte[-idx];
 }
 
 void *__kmap_local_pfn_prot(unsigned long pfn, pgprot_t prot)
 {
-	pte_t pteval, *kmap_pte = kmap_get_pte();
+	pte_t pteval, *kmap_pte;
 	unsigned long vaddr;
 	int idx;
 
@@ -525,9 +531,10 @@
 	preempt_disable();
 	idx = arch_kmap_local_map_idx(kmap_local_idx_push(), pfn);
 	vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
-	BUG_ON(!pte_none(*(kmap_pte - idx)));
+	kmap_pte = kmap_get_pte(vaddr, idx);
+	BUG_ON(!pte_none(*kmap_pte));
 	pteval = pfn_pte(pfn, prot);
-	arch_kmap_local_set_pte(&init_mm, vaddr, kmap_pte - idx, pteval);
+	arch_kmap_local_set_pte(&init_mm, vaddr, kmap_pte, pteval);
 	arch_kmap_local_post_map(vaddr, pteval);
 	current->kmap_ctrl.pteval[kmap_local_idx()] = pteval;
 	preempt_enable();
@@ -560,7 +567,7 @@
 void kunmap_local_indexed(void *vaddr)
 {
 	unsigned long addr = (unsigned long) vaddr & PAGE_MASK;
-	pte_t *kmap_pte = kmap_get_pte();
+	pte_t *kmap_pte;
 	int idx;
 
 	if (addr < __fix_to_virt(FIX_KMAP_END) ||
@@ -585,8 +592,9 @@
 	idx = arch_kmap_local_unmap_idx(kmap_local_idx(), addr);
 	WARN_ON_ONCE(addr != __fix_to_virt(FIX_KMAP_BEGIN + idx));
 
+	kmap_pte = kmap_get_pte(addr, idx);
 	arch_kmap_local_pre_unmap(addr);
-	pte_clear(&init_mm, addr, kmap_pte - idx);
+	pte_clear(&init_mm, addr, kmap_pte);
 	arch_kmap_local_post_unmap(addr);
 	current->kmap_ctrl.pteval[kmap_local_idx()] = __pte(0);
 	kmap_local_idx_pop();
@@ -608,7 +616,7 @@
 void __kmap_local_sched_out(void)
 {
 	struct task_struct *tsk = current;
-	pte_t *kmap_pte = kmap_get_pte();
+	pte_t *kmap_pte;
 	int i;
 
 	/* Clear kmaps */
@@ -619,7 +627,7 @@
 
 		/* With debug all even slots are unmapped and act as guard */
 		if (IS_ENABLED(CONFIG_DEBUG_KMAP_LOCAL) && !(i & 0x01)) {
-			WARN_ON_ONCE(!pte_none(pteval));
+			WARN_ON_ONCE(pte_val(pteval) != 0);
 			continue;
 		}
 		if (WARN_ON_ONCE(pte_none(pteval)))
@@ -635,8 +643,9 @@
 		idx = arch_kmap_local_map_idx(i, pte_pfn(pteval));
 
 		addr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
+		kmap_pte = kmap_get_pte(addr, idx);
 		arch_kmap_local_pre_unmap(addr);
-		pte_clear(&init_mm, addr, kmap_pte - idx);
+		pte_clear(&init_mm, addr, kmap_pte);
 		arch_kmap_local_post_unmap(addr);
 	}
 }
@@ -644,7 +653,7 @@
 void __kmap_local_sched_in(void)
 {
 	struct task_struct *tsk = current;
-	pte_t *kmap_pte = kmap_get_pte();
+	pte_t *kmap_pte;
 	int i;
 
 	/* Restore kmaps */
@@ -655,7 +664,7 @@
 
 		/* With debug all even slots are unmapped and act as guard */
 		if (IS_ENABLED(CONFIG_DEBUG_KMAP_LOCAL) && !(i & 0x01)) {
-			WARN_ON_ONCE(!pte_none(pteval));
+			WARN_ON_ONCE(pte_val(pteval) != 0);
 			continue;
 		}
 		if (WARN_ON_ONCE(pte_none(pteval)))
@@ -664,7 +673,8 @@
 		/* See comment in __kmap_local_sched_out() */
 		idx = arch_kmap_local_map_idx(i, pte_pfn(pteval));
 		addr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
-		set_pte_at(&init_mm, addr, kmap_pte - idx, pteval);
+		kmap_pte = kmap_get_pte(addr, idx);
+		set_pte_at(&init_mm, addr, kmap_pte, pteval);
 		arch_kmap_local_post_map(addr, pteval);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/mm/hmm.c
+++ linux-xilinx-zynqmp-5.15.0/mm/hmm.c
@@ -212,14 +212,6 @@
 		unsigned long end, unsigned long hmm_pfns[], pmd_t pmd);
 #endif /* CONFIG_TRANSPARENT_HUGEPAGE */
 
-static inline bool hmm_is_device_private_entry(struct hmm_range *range,
-		swp_entry_t entry)
-{
-	return is_device_private_entry(entry) &&
-		pfn_swap_entry_to_page(entry)->pgmap->owner ==
-		range->dev_private_owner;
-}
-
 static inline unsigned long pte_to_hmm_pfn_flags(struct hmm_range *range,
 						 pte_t pte)
 {
@@ -252,10 +244,12 @@
 		swp_entry_t entry = pte_to_swp_entry(pte);
 
 		/*
-		 * Never fault in device private pages, but just report
-		 * the PFN even if not present.
+		 * Don't fault in device private pages owned by the caller,
+		 * just report the PFN.
 		 */
-		if (hmm_is_device_private_entry(range, entry)) {
+		if (is_device_private_entry(entry) &&
+		    pfn_swap_entry_to_page(entry)->pgmap->owner ==
+		    range->dev_private_owner) {
 			cpu_flags = HMM_PFN_VALID;
 			if (is_writable_device_private_entry(entry))
 				cpu_flags |= HMM_PFN_WRITE;
@@ -273,6 +267,9 @@
 		if (!non_swap_entry(entry))
 			goto fault;
 
+		if (is_device_private_entry(entry))
+			goto fault;
+
 		if (is_device_exclusive_entry(entry))
 			goto fault;
 
@@ -300,7 +297,8 @@
 	 * Since each architecture defines a struct page for the zero page, just
 	 * fall through and treat it like a normal page.
 	 */
-	if (pte_special(pte) && !pte_devmap(pte) &&
+	if (!vm_normal_page(walk->vma, addr, pte) &&
+	    !pte_devmap(pte) &&
 	    !is_zero_pfn(pte_pfn(pte))) {
 		if (hmm_pte_need_fault(hmm_vma_walk, pfn_req_flags, 0)) {
 			pte_unmap(ptep);
@@ -518,7 +516,7 @@
 	struct hmm_range *range = hmm_vma_walk->range;
 	struct vm_area_struct *vma = walk->vma;
 
-	if (!(vma->vm_flags & (VM_IO | VM_PFNMAP | VM_MIXEDMAP)) &&
+	if (!(vma->vm_flags & (VM_IO | VM_PFNMAP)) &&
 	    vma->vm_flags & VM_READ)
 		return 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/huge_memory.c
+++ linux-xilinx-zynqmp-5.15.0/mm/huge_memory.c
@@ -1437,7 +1437,7 @@
 	vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
 	if (unlikely(!pmd_same(oldpmd, *vmf->pmd))) {
 		spin_unlock(vmf->ptl);
-		goto out;
+		return 0;
 	}
 
 	pmd = pmd_modify(oldpmd, vma->vm_page_prot);
@@ -1465,23 +1465,16 @@
 	if (migrated) {
 		flags |= TNF_MIGRATED;
 		page_nid = target_nid;
-	} else {
-		flags |= TNF_MIGRATE_FAIL;
-		vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
-		if (unlikely(!pmd_same(oldpmd, *vmf->pmd))) {
-			spin_unlock(vmf->ptl);
-			goto out;
-		}
-		goto out_map;
+		task_numa_fault(last_cpupid, page_nid, HPAGE_PMD_NR, flags);
+		return 0;
 	}
 
-out:
-	if (page_nid != NUMA_NO_NODE)
-		task_numa_fault(last_cpupid, page_nid, HPAGE_PMD_NR,
-				flags);
-
-	return 0;
-
+	flags |= TNF_MIGRATE_FAIL;
+	vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
+	if (unlikely(!pmd_same(oldpmd, *vmf->pmd))) {
+		spin_unlock(vmf->ptl);
+		return 0;
+	}
 out_map:
 	/* Restore the PMD */
 	pmd = pmd_modify(oldpmd, vma->vm_page_prot);
@@ -1491,7 +1484,10 @@
 	set_pmd_at(vma->vm_mm, haddr, vmf->pmd, pmd);
 	update_mmu_cache_pmd(vma, vmf->address, vmf->pmd);
 	spin_unlock(vmf->ptl);
-	goto out;
+
+	if (page_nid != NUMA_NO_NODE)
+		task_numa_fault(last_cpupid, page_nid, HPAGE_PMD_NR, flags);
+	return 0;
 }
 
 /*
@@ -1926,7 +1922,7 @@
 {
 	struct mm_struct *mm = vma->vm_mm;
 	pgtable_t pgtable;
-	pmd_t _pmd;
+	pmd_t _pmd, old_pmd;
 	int i;
 
 	/*
@@ -1937,7 +1933,7 @@
 	 *
 	 * See Documentation/vm/mmu_notifier.rst
 	 */
-	pmdp_huge_clear_flush(vma, haddr, pmd);
+	old_pmd = pmdp_huge_clear_flush(vma, haddr, pmd);
 
 	pgtable = pgtable_trans_huge_withdraw(mm, pmd);
 	pmd_populate(mm, &_pmd, pgtable);
@@ -1946,6 +1942,8 @@
 		pte_t *pte, entry;
 		entry = pfn_pte(my_zero_pfn(haddr), vma->vm_page_prot);
 		entry = pte_mkspecial(entry);
+		if (pmd_uffd_wp(old_pmd))
+			entry = pte_mkuffd_wp(entry);
 		pte = pte_offset_map(&_pmd, haddr);
 		VM_BUG_ON(!pte_none(*pte));
 		set_pte_at(mm, haddr, pte, entry);
@@ -2617,11 +2615,16 @@
 	struct address_space *mapping = NULL;
 	int extra_pins, ret;
 	pgoff_t end;
+	bool is_hzp;
 
-	VM_BUG_ON_PAGE(is_huge_zero_page(head), head);
 	VM_BUG_ON_PAGE(!PageLocked(head), head);
 	VM_BUG_ON_PAGE(!PageCompound(head), head);
 
+	is_hzp = is_huge_zero_page(head);
+	VM_WARN_ON_ONCE_PAGE(is_hzp, head);
+	if (is_hzp)
+		return -EBUSY;
+
 	if (PageWriteback(head))
 		return -EBUSY;
 
@@ -2773,6 +2776,9 @@
 	if (PageSwapCache(page))
 		return;
 
+	if (!list_empty(page_deferred_list(page)))
+		return;
+
 	spin_lock_irqsave(&ds_queue->split_queue_lock, flags);
 	if (list_empty(page_deferred_list(page))) {
 		count_vm_event(THP_DEFERRED_SPLIT_PAGE);
@@ -2874,14 +2880,15 @@
 	unsigned long total = 0, split = 0;
 
 	pr_debug("Split all THPs\n");
-	for_each_populated_zone(zone) {
+	for_each_zone(zone) {
+		if (!managed_zone(zone))
+			continue;
 		max_zone_pfn = zone_end_pfn(zone);
 		for (pfn = zone->zone_start_pfn; pfn < max_zone_pfn; pfn++) {
-			if (!pfn_valid(pfn))
-				continue;
+			int nr_pages;
 
-			page = pfn_to_page(pfn);
-			if (!get_page_unless_zero(page))
+			page = pfn_to_online_page(pfn);
+			if (!page || !get_page_unless_zero(page))
 				continue;
 
 			if (zone != page_zone(page))
@@ -2892,8 +2899,10 @@
 
 			total++;
 			lock_page(page);
+			nr_pages = thp_nr_pages(page);
 			if (!split_huge_page(page))
 				split++;
+			pfn += nr_pages - 1;
 			unlock_page(page);
 next:
 			put_page(page);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/hugetlb.c
+++ linux-xilinx-zynqmp-5.15.0/mm/hugetlb.c
@@ -82,6 +82,8 @@
 
 /* Forward declaration */
 static int hugetlb_acct_memory(struct hstate *h, long delta);
+static void hugetlb_unshare_pmds(struct vm_area_struct *vma,
+		unsigned long start, unsigned long end);
 
 static inline bool subpool_is_free(struct hugepage_subpool *spool)
 {
@@ -2654,8 +2656,7 @@
 		 * Fail with -EBUSY if not possible.
 		 */
 		spin_unlock_irq(&hugetlb_lock);
-		if (!isolate_huge_page(old_page, list))
-			ret = -EBUSY;
+		ret = isolate_hugetlb(old_page, list);
 		spin_lock_irq(&hugetlb_lock);
 		goto free_new;
 	} else if (!HPageFreed(old_page)) {
@@ -2731,7 +2732,7 @@
 	if (hstate_is_gigantic(h))
 		return -ENOMEM;
 
-	if (page_count(head) && isolate_huge_page(head, list))
+	if (page_count(head) && !isolate_hugetlb(head, list))
 		ret = 0;
 	else if (!page_count(head))
 		ret = alloc_and_dissolve_huge_page(h, head, list);
@@ -2813,11 +2814,11 @@
 		page = alloc_buddy_huge_page_with_mpol(h, vma, addr);
 		if (!page)
 			goto out_uncharge_cgroup;
+		spin_lock_irq(&hugetlb_lock);
 		if (!avoid_reserve && vma_has_reserves(vma, gbl_chg)) {
 			SetHPageRestoreReserve(page);
 			h->resv_huge_pages--;
 		}
-		spin_lock_irq(&hugetlb_lock);
 		list_add(&page->lru, &h->hugepage_activelist);
 		/* Fall through */
 	}
@@ -3716,7 +3717,7 @@
 	BUG_ON(hugetlb_max_hstate >= HUGE_MAX_HSTATE);
 	BUG_ON(order == 0);
 	h = &hstates[hugetlb_max_hstate++];
-	mutex_init(&h->resize_lock);
+	__mutex_init(&h->resize_lock, "resize mutex", &h->resize_key);
 	h->order = order;
 	h->mask = ~(huge_page_size(h) - 1);
 	for (i = 0; i < MAX_NUMNODES; ++i)
@@ -4164,6 +4165,25 @@
 {
 	if (addr & ~(huge_page_mask(hstate_vma(vma))))
 		return -EINVAL;
+
+	/*
+	 * PMD sharing is only possible for PUD_SIZE-aligned address ranges
+	 * in HugeTLB VMAs. If we will lose PUD_SIZE alignment due to this
+	 * split, unshare PMDs in the PUD_SIZE interval surrounding addr now.
+	 */
+	if (addr & ~PUD_MASK) {
+		/*
+		 * hugetlb_vm_op_split is called right before we attempt to
+		 * split the VMA. We will need to unshare PMDs in the old and
+		 * new VMAs, so let's unshare before we split.
+		 */
+		unsigned long floor = addr & PUD_MASK;
+		unsigned long ceil = floor + PUD_SIZE;
+
+		if (floor >= vma->vm_start && ceil <= vma->vm_end)
+			hugetlb_unshare_pmds(vma, floor, ceil);
+	}
+
 	return 0;
 }
 
@@ -4439,6 +4459,7 @@
 	struct hstate *h = hstate_vma(vma);
 	unsigned long sz = huge_page_size(h);
 	struct mmu_notifier_range range;
+	bool force_flush = false;
 
 	WARN_ON(!is_vm_hugetlb_page(vma));
 	BUG_ON(start & ~huge_page_mask(h));
@@ -4467,10 +4488,8 @@
 		ptl = huge_pte_lock(h, mm, ptep);
 		if (huge_pmd_unshare(mm, vma, &address, ptep)) {
 			spin_unlock(ptl);
-			/*
-			 * We just unmapped a page of PMDs by clearing a PUD.
-			 * The caller's TLB flush range should cover this area.
-			 */
+			tlb_flush_pmd_range(tlb, address & PUD_MASK, PUD_SIZE);
+			force_flush = true;
 			continue;
 		}
 
@@ -4527,6 +4546,22 @@
 	}
 	mmu_notifier_invalidate_range_end(&range);
 	tlb_end_vma(tlb, vma);
+
+	/*
+	 * If we unshared PMDs, the TLB flush was not recorded in mmu_gather. We
+	 * could defer the flush until now, since by holding i_mmap_rwsem we
+	 * guaranteed that the last refernece would not be dropped. But we must
+	 * do the flushing before we return, as otherwise i_mmap_rwsem will be
+	 * dropped and the last reference to the shared PMDs page might be
+	 * dropped as well.
+	 *
+	 * In theory we could defer the freeing of the PMD pages as well, but
+	 * huge_pmd_unshare() relies on the exact page_count for the PMD page to
+	 * detect sharing, so we cannot defer the release of the page either.
+	 * Instead, do flush now.
+	 */
+	if (force_flush)
+		tlb_flush_mmu_tlbonly(tlb);
 }
 
 void __unmap_hugepage_range_final(struct mmu_gather *tlb,
@@ -4829,7 +4864,6 @@
 						  unsigned long haddr,
 						  unsigned long reason)
 {
-	vm_fault_t ret;
 	u32 hash;
 	struct vm_fault vmf = {
 		.vma = vma,
@@ -4846,18 +4880,14 @@
 	};
 
 	/*
-	 * hugetlb_fault_mutex and i_mmap_rwsem must be
-	 * dropped before handling userfault.  Reacquire
-	 * after handling fault to make calling code simpler.
+	 * vma_lock and hugetlb_fault_mutex must be dropped before handling
+	 * userfault. Also mmap_lock will be dropped during handling
+	 * userfault, any vma operation should be careful from here.
 	 */
 	hash = hugetlb_fault_mutex_hash(mapping, idx);
 	mutex_unlock(&hugetlb_fault_mutex_table[hash]);
 	i_mmap_unlock_read(mapping);
-	ret = handle_userfault(&vmf, reason);
-	i_mmap_lock_read(mapping);
-	mutex_lock(&hugetlb_fault_mutex_table[hash]);
-
-	return ret;
+	return handle_userfault(&vmf, reason);
 }
 
 static vm_fault_t hugetlb_no_page(struct mm_struct *mm,
@@ -4874,6 +4904,7 @@
 	spinlock_t *ptl;
 	unsigned long haddr = address & huge_page_mask(h);
 	bool new_page, new_pagecache_page = false;
+	u32 hash = hugetlb_fault_mutex_hash(mapping, idx);
 
 	/*
 	 * Currently, we are forced to kill the process in the event the
@@ -4883,7 +4914,7 @@
 	if (is_vma_resv_set(vma, HPAGE_RESV_UNMAPPED)) {
 		pr_warn_ratelimited("PID %d killed due to inadequate hugepage pool\n",
 			   current->pid);
-		return ret;
+		goto out;
 	}
 
 	/*
@@ -4900,12 +4931,10 @@
 	page = find_lock_page(mapping, idx);
 	if (!page) {
 		/* Check for page in userfault range */
-		if (userfaultfd_missing(vma)) {
-			ret = hugetlb_handle_userfault(vma, mapping, idx,
+		if (userfaultfd_missing(vma))
+			return hugetlb_handle_userfault(vma, mapping, idx,
 						       flags, haddr,
 						       VM_UFFD_MISSING);
-			goto out;
-		}
 
 		page = alloc_huge_page(vma, haddr, 0);
 		if (IS_ERR(page)) {
@@ -4965,10 +4994,9 @@
 		if (userfaultfd_minor(vma)) {
 			unlock_page(page);
 			put_page(page);
-			ret = hugetlb_handle_userfault(vma, mapping, idx,
+			return hugetlb_handle_userfault(vma, mapping, idx,
 						       flags, haddr,
 						       VM_UFFD_MINOR);
-			goto out;
 		}
 	}
 
@@ -5019,6 +5047,8 @@
 
 	unlock_page(page);
 out:
+	mutex_unlock(&hugetlb_fault_mutex_table[hash]);
+	i_mmap_unlock_read(mapping);
 	return ret;
 
 backout:
@@ -5116,10 +5146,12 @@
 	mutex_lock(&hugetlb_fault_mutex_table[hash]);
 
 	entry = huge_ptep_get(ptep);
-	if (huge_pte_none(entry)) {
-		ret = hugetlb_no_page(mm, vma, mapping, idx, address, ptep, flags);
-		goto out_mutex;
-	}
+	if (huge_pte_none(entry))
+		/*
+		 * hugetlb_no_page will drop vma lock and hugetlb fault
+		 * mutex internally, which make us return immediately.
+		 */
+		return hugetlb_no_page(mm, vma, mapping, idx, address, ptep, flags);
 
 	ret = 0;
 
@@ -5236,13 +5268,14 @@
 	int ret = -ENOMEM;
 	struct page *page;
 	int writable;
-	bool new_pagecache_page = false;
+	bool page_in_pagecache = false;
 
 	if (is_continue) {
 		ret = -EFAULT;
 		page = find_lock_page(mapping, idx);
 		if (!page)
 			goto out;
+		page_in_pagecache = true;
 	} else if (!*pagep) {
 		/* If a page already exists, then it's UFFDIO_COPY for
 		 * a non-missing case. Return -EEXIST.
@@ -5298,6 +5331,7 @@
 
 		page = alloc_huge_page(dst_vma, dst_addr, 0);
 		if (IS_ERR(page)) {
+			put_page(*pagep);
 			ret = -ENOMEM;
 			*pagep = NULL;
 			goto out;
@@ -5330,12 +5364,16 @@
 		ret = huge_add_to_page_cache(page, mapping, idx);
 		if (ret)
 			goto out_release_nounlock;
-		new_pagecache_page = true;
+		page_in_pagecache = true;
 	}
 
 	ptl = huge_pte_lockptr(h, dst_mm, dst_pte);
 	spin_lock(ptl);
 
+	ret = -EIO;
+	if (PageHWPoison(page))
+		goto out_release_unlock;
+
 	/*
 	 * Recheck the i_size after holding PT lock to make sure not
 	 * to leave any page mapped (as page_mapped()) beyond the end
@@ -5354,7 +5392,7 @@
 	if (!huge_pte_none(huge_ptep_get(dst_pte)))
 		goto out_release_unlock;
 
-	if (vm_shared) {
+	if (page_in_pagecache) {
 		page_dup_rmap(page, true);
 	} else {
 		ClearHPageRestoreReserve(page);
@@ -5394,7 +5432,7 @@
 	if (vm_shared || is_continue)
 		unlock_page(page);
 out_release_nounlock:
-	if (!new_pagecache_page)
+	if (!page_in_pagecache)
 		restore_reserve_on_error(h, dst_vma, dst_addr, page);
 	put_page(page);
 	goto out;
@@ -6044,7 +6082,14 @@
 	pud_clear(pud);
 	put_page(virt_to_page(ptep));
 	mm_dec_nr_pmds(mm);
-	*addr = ALIGN(*addr, HPAGE_SIZE * PTRS_PER_PTE) - HPAGE_SIZE;
+	/*
+	 * This update of passed address optimizes loops sequentially
+	 * processing addresses in increments of huge page size (PMD_SIZE
+	 * in this case).  By clearing the pud, a PUD_SIZE area is unmapped.
+	 * Update address to the 'last page' in the cleared area so that
+	 * calling loop can move to first page past this area.
+	 */
+	*addr |= PUD_SIZE - PMD_SIZE;
 	return 1;
 }
 
@@ -6161,12 +6206,13 @@
 }
 
 struct page * __weak
-follow_huge_pmd(struct mm_struct *mm, unsigned long address,
-		pmd_t *pmd, int flags)
+follow_huge_pmd_pte(struct vm_area_struct *vma, unsigned long address, int flags)
 {
+	struct hstate *h = hstate_vma(vma);
+	struct mm_struct *mm = vma->vm_mm;
 	struct page *page = NULL;
 	spinlock_t *ptl;
-	pte_t pte;
+	pte_t *ptep, pte;
 
 	/* FOLL_GET and FOLL_PIN are mutually exclusive. */
 	if (WARN_ON_ONCE((flags & (FOLL_PIN | FOLL_GET)) ==
@@ -6174,17 +6220,15 @@
 		return NULL;
 
 retry:
-	ptl = pmd_lockptr(mm, pmd);
-	spin_lock(ptl);
-	/*
-	 * make sure that the address range covered by this pmd is not
-	 * unmapped from other threads.
-	 */
-	if (!pmd_huge(*pmd))
-		goto out;
-	pte = huge_ptep_get((pte_t *)pmd);
+	ptep = huge_pte_offset(mm, address, huge_page_size(h));
+	if (!ptep)
+		return NULL;
+
+	ptl = huge_pte_lock(h, mm, ptep);
+	pte = huge_ptep_get(ptep);
 	if (pte_present(pte)) {
-		page = pmd_page(*pmd) + ((address & ~PMD_MASK) >> PAGE_SHIFT);
+		page = pte_page(pte) +
+			((address & ~huge_page_mask(h)) >> PAGE_SHIFT);
 		/*
 		 * try_grab_page() should always succeed here, because: a) we
 		 * hold the pmd (ptl) lock, and b) we've just checked that the
@@ -6200,7 +6244,7 @@
 	} else {
 		if (is_hugetlb_entry_migration(pte)) {
 			spin_unlock(ptl);
-			__migration_entry_wait(mm, (pte_t *)pmd, ptl);
+			__migration_entry_wait(mm, ptep, ptl);
 			goto retry;
 		}
 		/*
@@ -6232,15 +6276,15 @@
 	return pte_page(*(pte_t *)pgd) + ((address & ~PGDIR_MASK) >> PAGE_SHIFT);
 }
 
-bool isolate_huge_page(struct page *page, struct list_head *list)
+int isolate_hugetlb(struct page *page, struct list_head *list)
 {
-	bool ret = true;
+	int ret = 0;
 
 	spin_lock_irq(&hugetlb_lock);
 	if (!PageHeadHuge(page) ||
 	    !HPageMigratable(page) ||
 	    !get_page_unless_zero(page)) {
-		ret = false;
+		ret = -EBUSY;
 		goto unlock;
 	}
 	ClearHPageMigratable(page);
@@ -6267,6 +6311,16 @@
 	return ret;
 }
 
+int get_huge_page_for_hwpoison(unsigned long pfn, int flags)
+{
+	int ret;
+
+	spin_lock_irq(&hugetlb_lock);
+	ret = __get_huge_page_for_hwpoison(pfn, flags);
+	spin_unlock_irq(&hugetlb_lock);
+	return ret;
+}
+
 void putback_active_hugepage(struct page *page)
 {
 	spin_lock_irq(&hugetlb_lock);
@@ -6315,26 +6369,21 @@
 	}
 }
 
-/*
- * This function will unconditionally remove all the shared pmd pgtable entries
- * within the specific vma for a hugetlbfs memory range.
- */
-void hugetlb_unshare_all_pmds(struct vm_area_struct *vma)
+static void hugetlb_unshare_pmds(struct vm_area_struct *vma,
+				   unsigned long start,
+				   unsigned long end)
 {
 	struct hstate *h = hstate_vma(vma);
 	unsigned long sz = huge_page_size(h);
 	struct mm_struct *mm = vma->vm_mm;
 	struct mmu_notifier_range range;
-	unsigned long address, start, end;
+	unsigned long address;
 	spinlock_t *ptl;
 	pte_t *ptep;
 
 	if (!(vma->vm_flags & VM_MAYSHARE))
 		return;
 
-	start = ALIGN(vma->vm_start, PUD_SIZE);
-	end = ALIGN_DOWN(vma->vm_end, PUD_SIZE);
-
 	if (start >= end)
 		return;
 
@@ -6366,6 +6415,16 @@
 	mmu_notifier_invalidate_range_end(&range);
 }
 
+/*
+ * This function will unconditionally remove all the shared pmd pgtable entries
+ * within the specific vma for a hugetlbfs memory range.
+ */
+void hugetlb_unshare_all_pmds(struct vm_area_struct *vma)
+{
+	hugetlb_unshare_pmds(vma, ALIGN(vma->vm_start, PUD_SIZE),
+			ALIGN_DOWN(vma->vm_end, PUD_SIZE));
+}
+
 #ifdef CONFIG_CMA
 static bool cma_reserve_called __initdata;
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/hwpoison-inject.c
+++ linux-xilinx-zynqmp-5.15.0/mm/hwpoison-inject.c
@@ -48,7 +48,8 @@
 
 inject:
 	pr_info("Injecting memory failure at pfn %#lx\n", pfn);
-	return memory_failure(pfn, 0);
+	err = memory_failure(pfn, 0);
+	return (err == -EOPNOTSUPP) ? 0 : err;
 }
 
 static int hwpoison_unpoison(void *data, u64 val)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/internal.h
+++ linux-xilinx-zynqmp-5.15.0/mm/internal.h
@@ -34,6 +34,25 @@
 
 void page_writeback_init(void);
 
+/*
+ * This is a file-backed mapping, and is about to be memory mapped - invoke its
+ * mmap hook and safely handle error conditions. On error, VMA hooks will be
+ * mutated.
+ *
+ * @file: File which backs the mapping.
+ * @vma:  VMA which we are mapping.
+ *
+ * Returns: 0 if success, error otherwise.
+ */
+int mmap_file(struct file *file, struct vm_area_struct *vma);
+
+/*
+ * If the VMA has a close hook then close it, and since closing it might leave
+ * it in an inconsistent state which makes the use of any hooks suspect, clear
+ * them down by installing dummy empty hooks.
+ */
+void vma_close(struct vm_area_struct *vma);
+
 vm_fault_t do_swap_page(struct vm_fault *vmf);
 
 void free_pgtables(struct mmu_gather *tlb, struct vm_area_struct *start_vma,
@@ -592,8 +611,13 @@
 #define ALLOC_OOM		ALLOC_NO_WATERMARKS
 #endif
 
-#define ALLOC_HARDER		 0x10 /* try to alloc harder */
-#define ALLOC_HIGH		 0x20 /* __GFP_HIGH set */
+#define ALLOC_NON_BLOCK		 0x10 /* Caller cannot block. Allow access
+				       * to 25% of the min watermark or
+				       * 62.5% if __GFP_HIGH is set.
+				       */
+#define ALLOC_MIN_RESERVE	 0x20 /* __GFP_HIGH set. Allow access to 50%
+				       * of the min watermark.
+				       */
 #define ALLOC_CPUSET		 0x40 /* check for correct cpuset */
 #define ALLOC_CMA		 0x80 /* allow allocations from CMA areas */
 #ifdef CONFIG_ZONE_DMA32
@@ -601,8 +625,12 @@
 #else
 #define ALLOC_NOFRAGMENT	  0x0
 #endif
+#define ALLOC_HIGHATOMIC	0x200 /* Allows access to MIGRATE_HIGHATOMIC */
 #define ALLOC_KSWAPD		0x800 /* allow waking of kswapd, __GFP_KSWAPD_RECLAIM set */
 
+/* Flags that allow allocations below the min watermark. */
+#define ALLOC_RESERVES (ALLOC_NON_BLOCK|ALLOC_MIN_RESERVE|ALLOC_HIGHATOMIC|ALLOC_OOM)
+
 enum ttu_flags;
 struct tlbflush_unmap_batch;
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kasan/quarantine.c
+++ linux-xilinx-zynqmp-5.15.0/mm/kasan/quarantine.c
@@ -132,12 +132,23 @@
 static void qlink_free(struct qlist_node *qlink, struct kmem_cache *cache)
 {
 	void *object = qlink_to_object(qlink, cache);
+	struct kasan_free_meta *meta = kasan_get_free_meta(cache, object);
 	unsigned long flags;
 
 	if (IS_ENABLED(CONFIG_SLAB))
 		local_irq_save(flags);
 
 	/*
+	 * If init_on_free is enabled and KASAN's free metadata is stored in
+	 * the object, zero the metadata. Otherwise, the object's memory will
+	 * not be properly zeroed, as KASAN saves the metadata after the slab
+	 * allocator zeroes the object.
+	 */
+	if (slab_want_init_on_free(cache) &&
+	    cache->kasan_info.free_meta_offset == 0)
+		memzero_explicit(meta, sizeof(*meta));
+
+	/*
 	 * As the object now gets freed from the quarantine, assume that its
 	 * free track is no longer valid.
 	 */
@@ -304,6 +315,13 @@
 	struct qlist_head *q;
 
 	q = this_cpu_ptr(&cpu_quarantine);
+	/*
+	 * Ensure the ordering between the writing to q->offline and
+	 * per_cpu_remove_cache.  Prevent cpu_quarantine from being corrupted
+	 * by interrupt.
+	 */
+	if (READ_ONCE(q->offline))
+		return;
 	qlist_move_cache(q, &to_free, cache);
 	qlist_free_all(&to_free, cache);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kasan/report.c
+++ linux-xilinx-zynqmp-5.15.0/mm/kasan/report.c
@@ -117,16 +117,8 @@
 	pr_err("==================================================================\n");
 	add_taint(TAINT_BAD_PAGE, LOCKDEP_NOW_UNRELIABLE);
 	spin_unlock_irqrestore(&report_lock, *flags);
-	if (panic_on_warn && !test_bit(KASAN_BIT_MULTI_SHOT, &kasan_flags)) {
-		/*
-		 * This thread may hit another WARN() in the panic path.
-		 * Resetting this prevents additional WARN() from panicking the
-		 * system on this thread.  Other threads are blocked by the
-		 * panic_mutex in panic().
-		 */
-		panic_on_warn = 0;
-		panic("panic_on_warn set ...\n");
-	}
+	if (!test_bit(KASAN_BIT_MULTI_SHOT, &kasan_flags))
+		check_panic_on_warn("KASAN");
 	if (kasan_arg_fault == KASAN_ARG_FAULT_PANIC)
 		panic("kasan.fault=panic set ...\n");
 	kasan_enable_current();
@@ -465,7 +457,7 @@
 	return ret;
 }
 
-#ifdef CONFIG_KASAN_INLINE
+#if defined(CONFIG_KASAN_GENERIC) || defined(CONFIG_KASAN_SW_TAGS)
 /*
  * With CONFIG_KASAN_INLINE, accesses to bogus pointers (outside the high
  * canonical half of the address space) cause out-of-bounds shadow memory reads
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kasan/shadow.c
+++ linux-xilinx-zynqmp-5.15.0/mm/kasan/shadow.c
@@ -493,7 +493,7 @@
 
 #else /* CONFIG_KASAN_VMALLOC */
 
-int kasan_module_alloc(void *addr, size_t size)
+int kasan_module_alloc(void *addr, size_t size, gfp_t gfp_mask)
 {
 	void *ret;
 	size_t scaled_size;
@@ -515,9 +515,14 @@
 			__builtin_return_address(0));
 
 	if (ret) {
+		struct vm_struct *vm = find_vm_area(addr);
 		__memset(ret, KASAN_SHADOW_INIT, shadow_size);
-		find_vm_area(addr)->flags |= VM_KASAN;
+		vm->flags |= VM_KASAN;
 		kmemleak_ignore(ret);
+
+		if (vm->flags & VM_DEFER_KMEMLEAK)
+			kmemleak_vmalloc(vm, size, gfp_mask);
+
 		return 0;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kfence/Makefile
+++ linux-xilinx-zynqmp-5.15.0/mm/kfence/Makefile
@@ -2,5 +2,5 @@
 
 obj-$(CONFIG_KFENCE) := core.o report.o
 
-CFLAGS_kfence_test.o := -g -fno-omit-frame-pointer -fno-optimize-sibling-calls
+CFLAGS_kfence_test.o := -fno-omit-frame-pointer -fno-optimize-sibling-calls
 obj-$(CONFIG_KFENCE_KUNIT_TEST) += kfence_test.o
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kfence/core.c
+++ linux-xilinx-zynqmp-5.15.0/mm/kfence/core.c
@@ -10,14 +10,20 @@
 #include <linux/atomic.h>
 #include <linux/bug.h>
 #include <linux/debugfs.h>
+#include <linux/hash.h>
 #include <linux/irq_work.h>
+#include <linux/jhash.h>
 #include <linux/kcsan-checks.h>
 #include <linux/kfence.h>
 #include <linux/kmemleak.h>
 #include <linux/list.h>
 #include <linux/lockdep.h>
+#include <linux/log2.h>
 #include <linux/memblock.h>
 #include <linux/moduleparam.h>
+#include <linux/nodemask.h>
+#include <linux/notifier.h>
+#include <linux/panic_notifier.h>
 #include <linux/random.h>
 #include <linux/rcupdate.h>
 #include <linux/sched/clock.h>
@@ -82,6 +88,18 @@
 };
 module_param_cb(sample_interval, &sample_interval_param_ops, &kfence_sample_interval, 0600);
 
+/* Pool usage% threshold when currently covered allocations are skipped. */
+static unsigned long kfence_skip_covered_thresh __read_mostly = 75;
+module_param_named(skip_covered_thresh, kfence_skip_covered_thresh, ulong, 0644);
+
+/* If true, use a deferrable timer. */
+static bool kfence_deferrable __read_mostly = IS_ENABLED(CONFIG_KFENCE_DEFERRABLE);
+module_param_named(deferrable, kfence_deferrable, bool, 0444);
+
+/* If true, check all canary bytes on panic. */
+static bool kfence_check_on_panic __read_mostly;
+module_param_named(check_on_panic, kfence_check_on_panic, bool, 0444);
+
 /* The pool of pages used for guard pages and objects. */
 char *__kfence_pool __ro_after_init;
 EXPORT_SYMBOL(__kfence_pool); /* Export for test modules. */
@@ -97,14 +115,41 @@
 static struct list_head kfence_freelist = LIST_HEAD_INIT(kfence_freelist);
 static DEFINE_RAW_SPINLOCK(kfence_freelist_lock); /* Lock protecting freelist. */
 
-#ifdef CONFIG_KFENCE_STATIC_KEYS
-/* The static key to set up a KFENCE allocation. */
+/*
+ * The static key to set up a KFENCE allocation; or if static keys are not used
+ * to gate allocations, to avoid a load and compare if KFENCE is disabled.
+ */
 DEFINE_STATIC_KEY_FALSE(kfence_allocation_key);
-#endif
 
 /* Gates the allocation, ensuring only one succeeds in a given period. */
 atomic_t kfence_allocation_gate = ATOMIC_INIT(1);
 
+/*
+ * A Counting Bloom filter of allocation coverage: limits currently covered
+ * allocations of the same source filling up the pool.
+ *
+ * Assuming a range of 15%-85% unique allocations in the pool at any point in
+ * time, the below parameters provide a probablity of 0.02-0.33 for false
+ * positive hits respectively:
+ *
+ *	P(alloc_traces) = (1 - e^(-HNUM * (alloc_traces / SIZE)) ^ HNUM
+ */
+#define ALLOC_COVERED_HNUM	2
+#define ALLOC_COVERED_ORDER	(const_ilog2(CONFIG_KFENCE_NUM_OBJECTS) + 2)
+#define ALLOC_COVERED_SIZE	(1 << ALLOC_COVERED_ORDER)
+#define ALLOC_COVERED_HNEXT(h)	hash_32(h, ALLOC_COVERED_ORDER)
+#define ALLOC_COVERED_MASK	(ALLOC_COVERED_SIZE - 1)
+static atomic_t alloc_covered[ALLOC_COVERED_SIZE];
+
+/* Stack depth used to determine uniqueness of an allocation. */
+#define UNIQUE_ALLOC_STACK_DEPTH ((size_t)8)
+
+/*
+ * Randomness for stack hashes, making the same collisions across reboots and
+ * different machines less likely.
+ */
+static u32 stack_hash_seed __ro_after_init;
+
 /* Statistics counters for debugfs. */
 enum kfence_counter_id {
 	KFENCE_COUNTER_ALLOCATED,
@@ -112,6 +157,9 @@
 	KFENCE_COUNTER_FREES,
 	KFENCE_COUNTER_ZOMBIES,
 	KFENCE_COUNTER_BUGS,
+	KFENCE_COUNTER_SKIP_INCOMPAT,
+	KFENCE_COUNTER_SKIP_CAPACITY,
+	KFENCE_COUNTER_SKIP_COVERED,
 	KFENCE_COUNTER_COUNT,
 };
 static atomic_long_t counters[KFENCE_COUNTER_COUNT];
@@ -121,40 +169,67 @@
 	[KFENCE_COUNTER_FREES]		= "total frees",
 	[KFENCE_COUNTER_ZOMBIES]	= "zombie allocations",
 	[KFENCE_COUNTER_BUGS]		= "total bugs",
+	[KFENCE_COUNTER_SKIP_INCOMPAT]	= "skipped allocations (incompatible)",
+	[KFENCE_COUNTER_SKIP_CAPACITY]	= "skipped allocations (capacity)",
+	[KFENCE_COUNTER_SKIP_COVERED]	= "skipped allocations (covered)",
 };
 static_assert(ARRAY_SIZE(counter_names) == KFENCE_COUNTER_COUNT);
 
 /* === Internals ============================================================ */
 
-static bool kfence_protect(unsigned long addr)
+static inline bool should_skip_covered(void)
 {
-	return !KFENCE_WARN_ON(!kfence_protect_page(ALIGN_DOWN(addr, PAGE_SIZE), true));
+	unsigned long thresh = (CONFIG_KFENCE_NUM_OBJECTS * kfence_skip_covered_thresh) / 100;
+
+	return atomic_long_read(&counters[KFENCE_COUNTER_ALLOCATED]) > thresh;
 }
 
-static bool kfence_unprotect(unsigned long addr)
+static u32 get_alloc_stack_hash(unsigned long *stack_entries, size_t num_entries)
 {
-	return !KFENCE_WARN_ON(!kfence_protect_page(ALIGN_DOWN(addr, PAGE_SIZE), false));
+	num_entries = min(num_entries, UNIQUE_ALLOC_STACK_DEPTH);
+	num_entries = filter_irq_stacks(stack_entries, num_entries);
+	return jhash(stack_entries, num_entries * sizeof(stack_entries[0]), stack_hash_seed);
 }
 
-static inline struct kfence_metadata *addr_to_metadata(unsigned long addr)
+/*
+ * Adds (or subtracts) count @val for allocation stack trace hash
+ * @alloc_stack_hash from Counting Bloom filter.
+ */
+static void alloc_covered_add(u32 alloc_stack_hash, int val)
 {
-	long index;
+	int i;
 
-	/* The checks do not affect performance; only called from slow-paths. */
+	for (i = 0; i < ALLOC_COVERED_HNUM; i++) {
+		atomic_add(val, &alloc_covered[alloc_stack_hash & ALLOC_COVERED_MASK]);
+		alloc_stack_hash = ALLOC_COVERED_HNEXT(alloc_stack_hash);
+	}
+}
 
-	if (!is_kfence_address((void *)addr))
-		return NULL;
+/*
+ * Returns true if the allocation stack trace hash @alloc_stack_hash is
+ * currently contained (non-zero count) in Counting Bloom filter.
+ */
+static bool alloc_covered_contains(u32 alloc_stack_hash)
+{
+	int i;
 
-	/*
-	 * May be an invalid index if called with an address at the edge of
-	 * __kfence_pool, in which case we would report an "invalid access"
-	 * error.
-	 */
-	index = (addr - (unsigned long)__kfence_pool) / (PAGE_SIZE * 2) - 1;
-	if (index < 0 || index >= CONFIG_KFENCE_NUM_OBJECTS)
-		return NULL;
+	for (i = 0; i < ALLOC_COVERED_HNUM; i++) {
+		if (!atomic_read(&alloc_covered[alloc_stack_hash & ALLOC_COVERED_MASK]))
+			return false;
+		alloc_stack_hash = ALLOC_COVERED_HNEXT(alloc_stack_hash);
+	}
+
+	return true;
+}
 
-	return &kfence_metadata[index];
+static bool kfence_protect(unsigned long addr)
+{
+	return !KFENCE_WARN_ON(!kfence_protect_page(ALIGN_DOWN(addr, PAGE_SIZE), true));
+}
+
+static bool kfence_unprotect(unsigned long addr)
+{
+	return !KFENCE_WARN_ON(!kfence_protect_page(ALIGN_DOWN(addr, PAGE_SIZE), false));
 }
 
 static inline unsigned long metadata_to_pageaddr(const struct kfence_metadata *meta)
@@ -183,19 +258,26 @@
  * Update the object's metadata state, including updating the alloc/free stacks
  * depending on the state transition.
  */
-static noinline void metadata_update_state(struct kfence_metadata *meta,
-					   enum kfence_object_state next)
+static noinline void
+metadata_update_state(struct kfence_metadata *meta, enum kfence_object_state next,
+		      unsigned long *stack_entries, size_t num_stack_entries)
 {
 	struct kfence_track *track =
 		next == KFENCE_OBJECT_FREED ? &meta->free_track : &meta->alloc_track;
 
 	lockdep_assert_held(&meta->lock);
 
-	/*
-	 * Skip over 1 (this) functions; noinline ensures we do not accidentally
-	 * skip over the caller by never inlining.
-	 */
-	track->num_stack_entries = stack_trace_save(track->stack_entries, KFENCE_STACK_DEPTH, 1);
+	if (stack_entries) {
+		memcpy(track->stack_entries, stack_entries,
+		       num_stack_entries * sizeof(stack_entries[0]));
+	} else {
+		/*
+		 * Skip over 1 (this) functions; noinline ensures we do not
+		 * accidentally skip over the caller by never inlining.
+		 */
+		num_stack_entries = stack_trace_save(track->stack_entries, KFENCE_STACK_DEPTH, 1);
+	}
+	track->num_stack_entries = num_stack_entries;
 	track->pid = task_pid_nr(current);
 	track->cpu = raw_smp_processor_id();
 	track->ts_nsec = local_clock(); /* Same source as printk timestamps. */
@@ -257,7 +339,9 @@
 	}
 }
 
-static void *kfence_guarded_alloc(struct kmem_cache *cache, size_t size, gfp_t gfp)
+static void *kfence_guarded_alloc(struct kmem_cache *cache, size_t size, gfp_t gfp,
+				  unsigned long *stack_entries, size_t num_stack_entries,
+				  u32 alloc_stack_hash)
 {
 	struct kfence_metadata *meta = NULL;
 	unsigned long flags;
@@ -271,8 +355,10 @@
 		list_del_init(&meta->list);
 	}
 	raw_spin_unlock_irqrestore(&kfence_freelist_lock, flags);
-	if (!meta)
+	if (!meta) {
+		atomic_long_inc(&counters[KFENCE_COUNTER_SKIP_CAPACITY]);
 		return NULL;
+	}
 
 	if (unlikely(!raw_spin_trylock_irqsave(&meta->lock, flags))) {
 		/*
@@ -314,10 +400,12 @@
 	addr = (void *)meta->addr;
 
 	/* Update remaining metadata. */
-	metadata_update_state(meta, KFENCE_OBJECT_ALLOCATED);
+	metadata_update_state(meta, KFENCE_OBJECT_ALLOCATED, stack_entries, num_stack_entries);
 	/* Pairs with READ_ONCE() in kfence_shutdown_cache(). */
 	WRITE_ONCE(meta->cache, cache);
 	meta->size = size;
+	meta->alloc_stack_hash = alloc_stack_hash;
+
 	for_each_canary(meta, set_canary_byte);
 
 	/* Set required struct page fields. */
@@ -330,6 +418,8 @@
 
 	raw_spin_unlock_irqrestore(&meta->lock, flags);
 
+	alloc_covered_add(alloc_stack_hash, 1);
+
 	/* Memory initialization. */
 
 	/*
@@ -394,10 +484,12 @@
 		memzero_explicit(addr, meta->size);
 
 	/* Mark the object as freed. */
-	metadata_update_state(meta, KFENCE_OBJECT_FREED);
+	metadata_update_state(meta, KFENCE_OBJECT_FREED, NULL, 0);
 
 	raw_spin_unlock_irqrestore(&meta->lock, flags);
 
+	alloc_covered_add(meta->alloc_stack_hash, -1);
+
 	/* Protect to detect use-after-frees. */
 	kfence_protect((unsigned long)addr);
 
@@ -429,6 +521,7 @@
 	unsigned long addr = (unsigned long)__kfence_pool;
 	struct page *pages;
 	int i;
+	char *p;
 
 	if (!__kfence_pool)
 		return false;
@@ -447,6 +540,8 @@
 	 * enters __slab_free() slow-path.
 	 */
 	for (i = 0; i < KFENCE_POOL_SIZE / PAGE_SIZE; i++) {
+		struct page *page = &pages[i];
+
 		if (!i || (i % 2))
 			continue;
 
@@ -454,7 +549,11 @@
 		if (WARN_ON(compound_head(&pages[i]) != &pages[i]))
 			goto err;
 
-		__SetPageSlab(&pages[i]);
+		__SetPageSlab(page);
+#ifdef CONFIG_MEMCG
+		page->memcg_data = (unsigned long)&kfence_metadata[i / 2 - 1].objcg |
+				   MEMCG_DATA_OBJCGS;
+#endif
 	}
 
 	/*
@@ -505,6 +604,16 @@
 	 * fails for the first page, and therefore expect addr==__kfence_pool in
 	 * most failure cases.
 	 */
+	for (p = (char *)addr; p < __kfence_pool + KFENCE_POOL_SIZE; p += PAGE_SIZE) {
+		struct page *page = virt_to_page(p);
+
+		if (!PageSlab(page))
+			continue;
+#ifdef CONFIG_MEMCG
+		page->memcg_data = 0;
+#endif
+		__ClearPageSlab(page);
+	}
 	memblock_free_late(__pa(addr), KFENCE_POOL_SIZE - (addr - (unsigned long)__kfence_pool));
 	__kfence_pool = NULL;
 	return false;
@@ -577,12 +686,17 @@
 	.open = open_objects,
 	.read = seq_read,
 	.llseek = seq_lseek,
+	.release = seq_release,
 };
 
-static int __init kfence_debugfs_init(void)
+static int kfence_debugfs_init(void)
 {
-	struct dentry *kfence_dir = debugfs_create_dir("kfence", NULL);
+	struct dentry *kfence_dir;
 
+	if (!READ_ONCE(kfence_enabled))
+		return 0;
+
+	kfence_dir = debugfs_create_dir("kfence", NULL);
 	debugfs_create_file("stats", 0444, kfence_dir, NULL, &stats_fops);
 	debugfs_create_file("objects", 0400, kfence_dir, NULL, &objects_fops);
 	return 0;
@@ -590,8 +704,35 @@
 
 late_initcall(kfence_debugfs_init);
 
+/* === Panic Notifier ====================================================== */
+
+static void kfence_check_all_canary(void)
+{
+	int i;
+
+	for (i = 0; i < CONFIG_KFENCE_NUM_OBJECTS; i++) {
+		struct kfence_metadata *meta = &kfence_metadata[i];
+
+		if (meta->state == KFENCE_OBJECT_ALLOCATED)
+			for_each_canary(meta, check_canary_byte);
+	}
+}
+
+static int kfence_check_canary_callback(struct notifier_block *nb,
+					unsigned long reason, void *arg)
+{
+	kfence_check_all_canary();
+	return NOTIFY_OK;
+}
+
+static struct notifier_block kfence_check_canary_notifier = {
+	.notifier_call = kfence_check_canary_callback,
+};
+
 /* === Allocation Gate Timer ================================================ */
 
+static struct delayed_work kfence_timer;
+
 #ifdef CONFIG_KFENCE_STATIC_KEYS
 /* Wait queue to wake up allocation-gate timer task. */
 static DECLARE_WAIT_QUEUE_HEAD(allocation_wait);
@@ -614,7 +755,6 @@
  * avoids IPIs, at the cost of not immediately capturing allocations if the
  * instructions remain cached.
  */
-static struct delayed_work kfence_timer;
 static void toggle_allocation_gate(struct work_struct *work)
 {
 	if (!READ_ONCE(kfence_enabled))
@@ -642,7 +782,6 @@
 	queue_delayed_work(system_unbound_wq, &kfence_timer,
 			   msecs_to_jiffies(kfence_sample_interval));
 }
-static DECLARE_DELAYED_WORK(kfence_timer, toggle_allocation_gate);
 
 /* === Public interface ===================================================== */
 
@@ -663,13 +802,26 @@
 	if (!kfence_sample_interval)
 		return;
 
+	stack_hash_seed = (u32)random_get_entropy();
 	if (!kfence_init_pool()) {
 		pr_err("%s failed\n", __func__);
 		return;
 	}
 
+	if (!IS_ENABLED(CONFIG_KFENCE_STATIC_KEYS))
+		static_branch_enable(&kfence_allocation_key);
+
+	if (kfence_deferrable)
+		INIT_DEFERRABLE_WORK(&kfence_timer, toggle_allocation_gate);
+	else
+		INIT_DELAYED_WORK(&kfence_timer, toggle_allocation_gate);
+
+	if (kfence_check_on_panic)
+		atomic_notifier_chain_register(&panic_notifier_list, &kfence_check_canary_notifier);
+
 	WRITE_ONCE(kfence_enabled, true);
 	queue_delayed_work(system_unbound_wq, &kfence_timer, 0);
+
 	pr_info("initialized - using %lu bytes for %d objects at 0x%p-0x%p\n", KFENCE_POOL_SIZE,
 		CONFIG_KFENCE_NUM_OBJECTS, (void *)__kfence_pool,
 		(void *)(__kfence_pool + KFENCE_POOL_SIZE));
@@ -736,12 +888,18 @@
 
 void *__kfence_alloc(struct kmem_cache *s, size_t size, gfp_t flags)
 {
+	unsigned long stack_entries[KFENCE_STACK_DEPTH];
+	size_t num_stack_entries;
+	u32 alloc_stack_hash;
+
 	/*
 	 * Perform size check before switching kfence_allocation_gate, so that
 	 * we don't disable KFENCE without making an allocation.
 	 */
-	if (size > PAGE_SIZE)
+	if (size > PAGE_SIZE) {
+		atomic_long_inc(&counters[KFENCE_COUNTER_SKIP_INCOMPAT]);
 		return NULL;
+	}
 
 	/*
 	 * Skip allocations from non-default zones, including DMA. We cannot
@@ -749,15 +907,13 @@
 	 * properties (e.g. reside in DMAable memory).
 	 */
 	if ((flags & GFP_ZONEMASK) ||
-	    (s->flags & (SLAB_CACHE_DMA | SLAB_CACHE_DMA32)))
+	    ((flags & __GFP_THISNODE) && num_online_nodes() > 1) ||
+	    (s->flags & (SLAB_CACHE_DMA | SLAB_CACHE_DMA32))) {
+		atomic_long_inc(&counters[KFENCE_COUNTER_SKIP_INCOMPAT]);
 		return NULL;
+	}
 
-	/*
-	 * allocation_gate only needs to become non-zero, so it doesn't make
-	 * sense to continue writing to it and pay the associated contention
-	 * cost, in case we have a large number of concurrent allocations.
-	 */
-	if (atomic_read(&kfence_allocation_gate) || atomic_inc_return(&kfence_allocation_gate) > 1)
+	if (atomic_inc_return(&kfence_allocation_gate) > 1)
 		return NULL;
 #ifdef CONFIG_KFENCE_STATIC_KEYS
 	/*
@@ -776,7 +932,25 @@
 	if (!READ_ONCE(kfence_enabled))
 		return NULL;
 
-	return kfence_guarded_alloc(s, size, flags);
+	num_stack_entries = stack_trace_save(stack_entries, KFENCE_STACK_DEPTH, 0);
+
+	/*
+	 * Do expensive check for coverage of allocation in slow-path after
+	 * allocation_gate has already become non-zero, even though it might
+	 * mean not making any allocation within a given sample interval.
+	 *
+	 * This ensures reasonable allocation coverage when the pool is almost
+	 * full, including avoiding long-lived allocations of the same source
+	 * filling up the pool (e.g. pagecache allocations).
+	 */
+	alloc_stack_hash = get_alloc_stack_hash(stack_entries, num_stack_entries);
+	if (should_skip_covered() && alloc_covered_contains(alloc_stack_hash)) {
+		atomic_long_inc(&counters[KFENCE_COUNTER_SKIP_COVERED]);
+		return NULL;
+	}
+
+	return kfence_guarded_alloc(s, size, flags, stack_entries, num_stack_entries,
+				    alloc_stack_hash);
 }
 
 size_t kfence_ksize(const void *addr)
@@ -805,6 +979,9 @@
 {
 	struct kfence_metadata *meta = addr_to_metadata((unsigned long)addr);
 
+#ifdef CONFIG_MEMCG
+	KFENCE_WARN_ON(meta->objcg);
+#endif
 	/*
 	 * If the objects of the cache are SLAB_TYPESAFE_BY_RCU, defer freeing
 	 * the object, as the object page may be recycled for other-typed
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kfence/kfence.h
+++ linux-xilinx-zynqmp-5.15.0/mm/kfence/kfence.h
@@ -87,10 +87,36 @@
 	/* Allocation and free stack information. */
 	struct kfence_track alloc_track;
 	struct kfence_track free_track;
+	/* For updating alloc_covered on frees. */
+	u32 alloc_stack_hash;
+#ifdef CONFIG_MEMCG
+	struct obj_cgroup *objcg;
+#endif
 };
 
 extern struct kfence_metadata kfence_metadata[CONFIG_KFENCE_NUM_OBJECTS];
 
+static inline struct kfence_metadata *addr_to_metadata(unsigned long addr)
+{
+	long index;
+
+	/* The checks do not affect performance; only called from slow-paths. */
+
+	if (!is_kfence_address((void *)addr))
+		return NULL;
+
+	/*
+	 * May be an invalid index if called with an address at the edge of
+	 * __kfence_pool, in which case we would report an "invalid access"
+	 * error.
+	 */
+	index = (addr - (unsigned long)__kfence_pool) / (PAGE_SIZE * 2) - 1;
+	if (index < 0 || index >= CONFIG_KFENCE_NUM_OBJECTS)
+		return NULL;
+
+	return &kfence_metadata[index];
+}
+
 /* KFENCE error types for report generation. */
 enum kfence_error_type {
 	KFENCE_ERROR_OOB,		/* Detected a out-of-bounds access. */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kfence/report.c
+++ linux-xilinx-zynqmp-5.15.0/mm/kfence/report.c
@@ -267,9 +267,55 @@
 
 	lockdep_on();
 
-	if (panic_on_warn)
-		panic("panic_on_warn set ...\n");
+	check_panic_on_warn("KFENCE");
 
 	/* We encountered a memory safety error, taint the kernel! */
 	add_taint(TAINT_BAD_PAGE, LOCKDEP_STILL_OK);
 }
+
+#ifdef CONFIG_PRINTK
+static void kfence_to_kp_stack(const struct kfence_track *track, void **kp_stack)
+{
+	int i, j;
+
+	i = get_stack_skipnr(track->stack_entries, track->num_stack_entries, NULL);
+	for (j = 0; i < track->num_stack_entries && j < KS_ADDRS_COUNT; ++i, ++j)
+		kp_stack[j] = (void *)track->stack_entries[i];
+	if (j < KS_ADDRS_COUNT)
+		kp_stack[j] = NULL;
+}
+
+bool __kfence_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
+{
+	struct kfence_metadata *meta = addr_to_metadata((unsigned long)object);
+	unsigned long flags;
+
+	if (!meta)
+		return false;
+
+	/*
+	 * If state is UNUSED at least show the pointer requested; the rest
+	 * would be garbage data.
+	 */
+	kpp->kp_ptr = object;
+
+	/* Requesting info an a never-used object is almost certainly a bug. */
+	if (WARN_ON(meta->state == KFENCE_OBJECT_UNUSED))
+		return true;
+
+	raw_spin_lock_irqsave(&meta->lock, flags);
+
+	kpp->kp_page = page;
+	kpp->kp_slab_cache = meta->cache;
+	kpp->kp_objp = (void *)meta->addr;
+	kfence_to_kp_stack(&meta->alloc_track, kpp->kp_stack);
+	if (meta->state == KFENCE_OBJECT_FREED)
+		kfence_to_kp_stack(&meta->free_track, kpp->kp_free_stack);
+	/* get_stack_skipnr() ensures the first entry is outside allocator. */
+	kpp->kp_ret = kpp->kp_stack[0];
+
+	raw_spin_unlock_irqrestore(&meta->lock, flags);
+
+	return true;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/mm/khugepaged.c
+++ linux-xilinx-zynqmp-5.15.0/mm/khugepaged.c
@@ -625,6 +625,10 @@
 			result = SCAN_PTE_NON_PRESENT;
 			goto out;
 		}
+		if (pte_uffd_wp(pteval)) {
+			result = SCAN_PTE_UFFD_WP;
+			goto out;
+		}
 		page = vm_normal_page(vma, address, pteval);
 		if (unlikely(!page)) {
 			result = SCAN_PAGE_NULL;
@@ -1146,14 +1150,17 @@
 
 	pmd_ptl = pmd_lock(mm, pmd); /* probably unnecessary */
 	/*
-	 * After this gup_fast can't run anymore. This also removes
-	 * any huge TLB entry from the CPU so we won't allow
-	 * huge and small TLB entries for the same virtual address
-	 * to avoid the risk of CPU bugs in that area.
+	 * This removes any huge TLB entry from the CPU so we won't allow
+	 * huge and small TLB entries for the same virtual address to
+	 * avoid the risk of CPU bugs in that area.
+	 *
+	 * Parallel fast GUP is fine since fast GUP will back off when
+	 * it detects PMD is changed.
 	 */
 	_pmd = pmdp_collapse_flush(vma, address, pmd);
 	spin_unlock(pmd_ptl);
 	mmu_notifier_invalidate_range_end(&range);
+	tlb_remove_table_sync_one();
 
 	spin_lock(pte_ptl);
 	isolated = __collapse_huge_page_isolate(vma, address, pte,
@@ -1440,6 +1447,7 @@
 	spinlock_t *ptl;
 	int count = 0;
 	int i;
+	struct mmu_notifier_range range;
 
 	if (!vma || !vma->vm_file ||
 	    !range_in_vma(vma, haddr, haddr + HPAGE_PMD_SIZE))
@@ -1466,6 +1474,19 @@
 	if (!pmd)
 		goto drop_hpage;
 
+	/*
+	 * We need to lock the mapping so that from here on, only GUP-fast and
+	 * hardware page walks can access the parts of the page tables that
+	 * we're operating on.
+	 */
+	i_mmap_lock_write(vma->vm_file->f_mapping);
+
+	/*
+	 * This spinlock should be unnecessary: Nobody else should be accessing
+	 * the page tables under spinlock protection here, only
+	 * lockless_pages_from_mm() and the hardware page walker can access page
+	 * tables while all the high-level locks are held in write mode.
+	 */
 	start_pte = pte_offset_map_lock(mm, pmd, haddr, &ptl);
 
 	/* step 1: check all mapped PTEs are to the right huge page */
@@ -1512,12 +1533,23 @@
 	}
 
 	/* step 4: collapse pmd */
-	ptl = pmd_lock(vma->vm_mm, pmd);
+	/* we make no change to anon, but protect concurrent anon page lookup */
+	if (vma->anon_vma)
+		anon_vma_lock_write(vma->anon_vma);
+
+	mmu_notifier_range_init(&range, MMU_NOTIFY_CLEAR, 0, NULL, mm, haddr,
+				haddr + HPAGE_PMD_SIZE);
+	mmu_notifier_invalidate_range_start(&range);
 	_pmd = pmdp_collapse_flush(vma, haddr, pmd);
-	spin_unlock(ptl);
 	mm_dec_nr_ptes(mm);
+	tlb_remove_table_sync_one();
+	mmu_notifier_invalidate_range_end(&range);
 	pte_free(mm, pmd_pgtable(_pmd));
 
+	if (vma->anon_vma)
+		anon_vma_unlock_write(vma->anon_vma);
+	i_mmap_unlock_write(vma->vm_file->f_mapping);
+
 drop_hpage:
 	unlock_page(hpage);
 	put_page(hpage);
@@ -1525,6 +1557,7 @@
 
 abort:
 	pte_unmap_unlock(start_pte, ptl);
+	i_mmap_unlock_write(vma->vm_file->f_mapping);
 	goto drop_hpage;
 }
 
@@ -1573,7 +1606,8 @@
 		 * An alternative would be drop the check, but check that page
 		 * table is clear before calling pmdp_collapse_flush() under
 		 * ptl. It has higher chance to recover THP for the VMA, but
-		 * has higher cost too.
+		 * has higher cost too. It would also probably require locking
+		 * the anon_vma.
 		 */
 		if (vma->anon_vma)
 			continue;
@@ -1595,12 +1629,19 @@
 		 */
 		if (mmap_write_trylock(mm)) {
 			if (!khugepaged_test_exit(mm)) {
-				spinlock_t *ptl = pmd_lock(mm, pmd);
+				struct mmu_notifier_range range;
+
+				mmu_notifier_range_init(&range,
+							MMU_NOTIFY_CLEAR, 0,
+							NULL, mm, addr,
+							addr + HPAGE_PMD_SIZE);
+				mmu_notifier_invalidate_range_start(&range);
 				/* assume page table is clear */
 				_pmd = pmdp_collapse_flush(vma, addr, pmd);
-				spin_unlock(ptl);
 				mm_dec_nr_ptes(mm);
+				tlb_remove_table_sync_one();
 				pte_free(mm, pmd_pgtable(_pmd));
+				mmu_notifier_invalidate_range_end(&range);
 			}
 			mmap_write_unlock(mm);
 		} else {
--- linux-xilinx-zynqmp-5.15.0.orig/mm/kmemleak.c
+++ linux-xilinx-zynqmp-5.15.0/mm/kmemleak.c
@@ -789,6 +789,8 @@
 	unsigned long flags;
 	struct kmemleak_object *object;
 	struct kmemleak_scan_area *area = NULL;
+	unsigned long untagged_ptr;
+	unsigned long untagged_objp;
 
 	object = find_and_get_object(ptr, 1);
 	if (!object) {
@@ -797,6 +799,9 @@
 		return;
 	}
 
+	untagged_ptr = (unsigned long)kasan_reset_tag((void *)ptr);
+	untagged_objp = (unsigned long)kasan_reset_tag((void *)object->pointer);
+
 	if (scan_area_cache)
 		area = kmem_cache_alloc(scan_area_cache, gfp_kmemleak_mask(gfp));
 
@@ -808,8 +813,8 @@
 		goto out_unlock;
 	}
 	if (size == SIZE_MAX) {
-		size = object->pointer + object->size - ptr;
-	} else if (ptr + size > object->pointer + object->size) {
+		size = untagged_objp + object->size - untagged_ptr;
+	} else if (untagged_ptr + size > untagged_objp + object->size) {
 		kmemleak_warn("Scan area larger than object 0x%08lx\n", ptr);
 		dump_object_info(object);
 		kmem_cache_free(scan_area_cache, area);
@@ -1403,7 +1408,8 @@
 {
 	unsigned long flags;
 	struct kmemleak_object *object;
-	int i;
+	struct zone *zone;
+	int __maybe_unused i;
 	int new_leaks = 0;
 
 	jiffies_last_scan = jiffies;
@@ -1443,9 +1449,9 @@
 	 * Struct page scanning for each node.
 	 */
 	get_online_mems();
-	for_each_online_node(i) {
-		unsigned long start_pfn = node_start_pfn(i);
-		unsigned long end_pfn = node_end_pfn(i);
+	for_each_populated_zone(zone) {
+		unsigned long start_pfn = zone->zone_start_pfn;
+		unsigned long end_pfn = zone_end_pfn(zone);
 		unsigned long pfn;
 
 		for (pfn = start_pfn; pfn < end_pfn; pfn++) {
@@ -1454,8 +1460,8 @@
 			if (!page)
 				continue;
 
-			/* only scan pages belonging to this node */
-			if (page_to_nid(page) != i)
+			/* only scan pages belonging to this zone */
+			if (page_zone(page) != zone)
 				continue;
 			/* only scan if page is in use */
 			if (page_count(page) == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/ksm.c
+++ linux-xilinx-zynqmp-5.15.0/mm/ksm.c
@@ -2415,9 +2415,14 @@
 
 		if (ksmd_should_run()) {
 			sleep_ms = READ_ONCE(ksm_thread_sleep_millisecs);
-			wait_event_interruptible_timeout(ksm_iter_wait,
-				sleep_ms != READ_ONCE(ksm_thread_sleep_millisecs),
-				msecs_to_jiffies(sleep_ms));
+			if (sleep_ms >= 1000)
+				wait_event_interruptible_timeout(ksm_iter_wait,
+					sleep_ms != READ_ONCE(ksm_thread_sleep_millisecs),
+					msecs_to_jiffies(round_jiffies_relative(sleep_ms)));
+			else
+				wait_event_interruptible_timeout(ksm_iter_wait,
+					sleep_ms != READ_ONCE(ksm_thread_sleep_millisecs),
+					msecs_to_jiffies(sleep_ms));
 		} else {
 			wait_event_freezable(ksm_thread_wait,
 				ksmd_should_run() || kthread_should_stop());
--- linux-xilinx-zynqmp-5.15.0.orig/mm/maccess.c
+++ linux-xilinx-zynqmp-5.15.0/mm/maccess.c
@@ -99,7 +99,7 @@
 	return src - unsafe_addr;
 Efault:
 	pagefault_enable();
-	dst[-1] = '\0';
+	dst[0] = '\0';
 	return -EFAULT;
 }
 #else /* HAVE_GET_KERNEL_NOFAULT */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/madvise.c
+++ linux-xilinx-zynqmp-5.15.0/mm/madvise.c
@@ -436,8 +436,11 @@
 			continue;
 		}
 
-		/* Do not interfere with other mappings of this page */
-		if (page_mapcount(page) != 1)
+		/*
+		 * Do not interfere with other mappings of this page and
+		 * non-LRU page.
+		 */
+		if (!PageLRU(page) || page_mapcount(page) != 1)
 			continue;
 
 		VM_BUG_ON_PAGE(PageTransCompound(page), page);
@@ -968,6 +971,8 @@
 			pr_info("Injecting memory failure for pfn %#lx at process virtual address %#lx\n",
 				 pfn, start);
 			ret = memory_failure(pfn, MF_COUNT_INCREASED);
+			if (ret == -EOPNOTSUPP)
+				ret = 0;
 		}
 
 		if (ret)
@@ -1294,8 +1299,7 @@
 		iov_iter_advance(&iter, iovec.iov_len);
 	}
 
-	if (ret == 0)
-		ret = total_len - iov_iter_count(&iter);
+	ret = (total_len - iov_iter_count(&iter)) ? : ret;
 
 release_mm:
 	mmput(mm);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memblock.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memblock.c
@@ -366,14 +366,20 @@
 		addr = __pa(memblock.reserved.regions);
 		size = PAGE_ALIGN(sizeof(struct memblock_region) *
 				  memblock.reserved.max);
-		__memblock_free_late(addr, size);
+		if (memblock_reserved_in_slab)
+			kfree(memblock.reserved.regions);
+		else
+			__memblock_free_late(addr, size);
 	}
 
 	if (memblock.memory.regions != memblock_memory_init_regions) {
 		addr = __pa(memblock.memory.regions);
 		size = PAGE_ALIGN(sizeof(struct memblock_region) *
 				  memblock.memory.max);
-		__memblock_free_late(addr, size);
+		if (memblock_memory_in_slab)
+			kfree(memblock.memory.regions);
+		else
+			__memblock_free_late(addr, size);
 	}
 
 	memblock_memory = NULL;
@@ -655,6 +661,7 @@
  * @base: base address of the new region
  * @size: size of the new region
  * @nid: nid of the new region
+ * @flags: flags of the new region
  *
  * Add new memblock region [@base, @base + @size) to the "memory"
  * type. See memblock_add_range() description for mode details
@@ -663,14 +670,14 @@
  * 0 on success, -errno on failure.
  */
 int __init_memblock memblock_add_node(phys_addr_t base, phys_addr_t size,
-				       int nid)
+				      int nid, enum memblock_flags flags)
 {
 	phys_addr_t end = base + size - 1;
 
-	memblock_dbg("%s: [%pa-%pa] nid=%d %pS\n", __func__,
-		     &base, &end, nid, (void *)_RET_IP_);
+	memblock_dbg("%s: [%pa-%pa] nid=%d flags=%x %pS\n", __func__,
+		     &base, &end, nid, flags, (void *)_RET_IP_);
 
-	return memblock_add_range(&memblock.memory, base, size, nid, 0);
+	return memblock_add_range(&memblock.memory, base, size, nid, flags);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memcontrol.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memcontrol.c
@@ -103,11 +103,6 @@
 	return !cgroup_subsys_on_dfl(memory_cgrp_subsys) && !cgroup_memory_noswap;
 }
 
-/* memcg and lruvec stats flushing */
-static void flush_memcg_stats_dwork(struct work_struct *w);
-static DECLARE_DEFERRABLE_WORK(stats_flush_dwork, flush_memcg_stats_dwork);
-static DEFINE_SPINLOCK(stats_flush_lock);
-
 #define THRESHOLDS_EVENTS_TARGET 128
 #define SOFTLIMIT_EVENTS_TARGET 1024
 
@@ -239,7 +234,7 @@
 	     iter != NULL;				\
 	     iter = mem_cgroup_iter(NULL, iter, NULL))
 
-static inline bool should_force_charge(void)
+static inline bool task_is_dying(void)
 {
 	return tsk_is_oom_victim(current) || fatal_signal_pending(current) ||
 		(current->flags & PF_EXITING);
@@ -259,7 +254,7 @@
 }
 
 #ifdef CONFIG_MEMCG_KMEM
-extern spinlock_t css_set_lock;
+static DEFINE_SPINLOCK(objcg_lock);
 
 bool mem_cgroup_kmem_disabled(void)
 {
@@ -303,9 +298,9 @@
 	if (nr_pages)
 		obj_cgroup_uncharge_pages(objcg, nr_pages);
 
-	spin_lock_irqsave(&css_set_lock, flags);
+	spin_lock_irqsave(&objcg_lock, flags);
 	list_del(&objcg->list);
-	spin_unlock_irqrestore(&css_set_lock, flags);
+	spin_unlock_irqrestore(&objcg_lock, flags);
 
 	percpu_ref_exit(ref);
 	kfree_rcu(objcg, rcu);
@@ -337,7 +332,7 @@
 
 	objcg = rcu_replace_pointer(memcg->objcg, NULL, true);
 
-	spin_lock_irq(&css_set_lock);
+	spin_lock_irq(&objcg_lock);
 
 	/* 1) Ready to reparent active objcg. */
 	list_add(&objcg->list, &memcg->objcg_list);
@@ -347,7 +342,7 @@
 	/* 3) Move already reparented objcgs to the parent's list */
 	list_splice(&memcg->objcg_list, &parent->objcg_list);
 
-	spin_unlock_irq(&css_set_lock);
+	spin_unlock_irq(&objcg_lock);
 
 	percpu_ref_kill(&objcg->refcnt);
 }
@@ -635,6 +630,81 @@
 	return mz;
 }
 
+/*
+ * memcg and lruvec stats flushing
+ *
+ * Many codepaths leading to stats update or read are performance sensitive and
+ * adding stats flushing in such codepaths is not desirable. So, to optimize the
+ * flushing the kernel does:
+ *
+ * 1) Periodically and asynchronously flush the stats every 2 seconds to not let
+ *    rstat update tree grow unbounded.
+ *
+ * 2) Flush the stats synchronously on reader side only when there are more than
+ *    (MEMCG_CHARGE_BATCH * nr_cpus) update events. Though this optimization
+ *    will let stats be out of sync by atmost (MEMCG_CHARGE_BATCH * nr_cpus) but
+ *    only for 2 seconds due to (1).
+ */
+static void flush_memcg_stats_dwork(struct work_struct *w);
+static DECLARE_DEFERRABLE_WORK(stats_flush_dwork, flush_memcg_stats_dwork);
+static DEFINE_SPINLOCK(stats_flush_lock);
+static DEFINE_PER_CPU(unsigned int, stats_updates);
+static atomic_t stats_flush_threshold = ATOMIC_INIT(0);
+static u64 flush_next_time;
+
+#define FLUSH_TIME (2UL*HZ)
+
+static inline void memcg_rstat_updated(struct mem_cgroup *memcg, int val)
+{
+	unsigned int x;
+
+	cgroup_rstat_updated(memcg->css.cgroup, smp_processor_id());
+
+	x = __this_cpu_add_return(stats_updates, abs(val));
+	if (x > MEMCG_CHARGE_BATCH) {
+		/*
+		 * If stats_flush_threshold exceeds the threshold
+		 * (>num_online_cpus()), cgroup stats update will be triggered
+		 * in __mem_cgroup_flush_stats(). Increasing this var further
+		 * is redundant and simply adds overhead in atomic update.
+		 */
+		if (atomic_read(&stats_flush_threshold) <= num_online_cpus())
+			atomic_add(x / MEMCG_CHARGE_BATCH, &stats_flush_threshold);
+		__this_cpu_write(stats_updates, 0);
+	}
+}
+
+static void __mem_cgroup_flush_stats(void)
+{
+	unsigned long flag;
+
+	if (!spin_trylock_irqsave(&stats_flush_lock, flag))
+		return;
+
+	flush_next_time = jiffies_64 + 2*FLUSH_TIME;
+	cgroup_rstat_flush_irqsafe(root_mem_cgroup->css.cgroup);
+	atomic_set(&stats_flush_threshold, 0);
+	spin_unlock_irqrestore(&stats_flush_lock, flag);
+}
+
+void mem_cgroup_flush_stats(void)
+{
+	if (atomic_read(&stats_flush_threshold) > num_online_cpus())
+		__mem_cgroup_flush_stats();
+}
+
+void mem_cgroup_flush_stats_delayed(void)
+{
+	if (time_after64(jiffies_64, flush_next_time))
+		mem_cgroup_flush_stats();
+}
+
+static void flush_memcg_stats_dwork(struct work_struct *w)
+{
+	__mem_cgroup_flush_stats();
+	queue_delayed_work(system_unbound_wq, &stats_flush_dwork, FLUSH_TIME);
+}
+
 /**
  * __mod_memcg_state - update cgroup memory statistics
  * @memcg: the memory cgroup
@@ -647,7 +717,7 @@
 		return;
 
 	__this_cpu_add(memcg->vmstats_percpu->state[idx], val);
-	cgroup_rstat_updated(memcg->css.cgroup, smp_processor_id());
+	memcg_rstat_updated(memcg, val);
 }
 
 /* idx can be of type enum memcg_stat_item or node_stat_item. */
@@ -675,10 +745,12 @@
 	memcg = pn->memcg;
 
 	/* Update memcg */
-	__mod_memcg_state(memcg, idx, val);
+	__this_cpu_add(memcg->vmstats_percpu->state[idx], val);
 
 	/* Update lruvec */
 	__this_cpu_add(pn->lruvec_stats_percpu->state[idx], val);
+
+	memcg_rstat_updated(memcg, val);
 }
 
 /**
@@ -780,7 +852,7 @@
 		return;
 
 	__this_cpu_add(memcg->vmstats_percpu->events[idx], count);
-	cgroup_rstat_updated(memcg->css.cgroup, smp_processor_id());
+	memcg_rstat_updated(memcg, count);
 }
 
 static unsigned long memcg_events(struct mem_cgroup *memcg, int event)
@@ -1129,6 +1201,7 @@
 {
 	struct mem_cgroup *iter;
 	int ret = 0;
+	int i = 0;
 
 	BUG_ON(memcg == root_mem_cgroup);
 
@@ -1137,8 +1210,12 @@
 		struct task_struct *task;
 
 		css_task_iter_start(&iter->css, CSS_TASK_ITER_PROCS, &it);
-		while (!ret && (task = css_task_iter_next(&it)))
+		while (!ret && (task = css_task_iter_next(&it))) {
+			/* Avoid potential softlockup warning */
+			if ((++i & 1023) == 0)
+				cond_resched();
 			ret = fn(task, arg);
+		}
 		css_task_iter_end(&it);
 		if (ret) {
 			mem_cgroup_iter_break(memcg, iter);
@@ -1414,7 +1491,7 @@
 	 *
 	 * Current memory state:
 	 */
-	cgroup_rstat_flush(memcg->css.cgroup);
+	mem_cgroup_flush_stats();
 
 	for (i = 0; i < ARRAY_SIZE(memory_stats); i++) {
 		u64 size;
@@ -1575,7 +1652,7 @@
 	 * A few threads which were not waiting at mutex_lock_killable() can
 	 * fail to bail out. Therefore, check again after holding oom_lock.
 	 */
-	ret = should_force_charge() || out_of_memory(&oc);
+	ret = task_is_dying() || out_of_memory(&oc);
 
 unlock:
 	mutex_unlock(&oom_lock);
@@ -2530,6 +2607,7 @@
 	struct page_counter *counter;
 	enum oom_status oom_status;
 	unsigned long nr_reclaimed;
+	bool passed_oom = false;
 	bool may_swap = true;
 	bool drained = false;
 	unsigned long pflags;
@@ -2565,15 +2643,6 @@
 		goto force;
 
 	/*
-	 * Unlike in global OOM situations, memcg is not in a physical
-	 * memory shortage.  Allow dying and OOM-killed tasks to
-	 * bypass the last charges so that they can exit quickly and
-	 * free their memory.
-	 */
-	if (unlikely(should_force_charge()))
-		goto force;
-
-	/*
 	 * Prevent unbounded recursion when reclaim operations need to
 	 * allocate memory. This might exceed the limits temporarily,
 	 * but we prefer facilitating memory reclaim and getting back
@@ -2630,8 +2699,9 @@
 	if (gfp_mask & __GFP_RETRY_MAYFAIL)
 		goto nomem;
 
-	if (fatal_signal_pending(current))
-		goto force;
+	/* Avoid endless loop for tasks bypassed by the oom killer */
+	if (passed_oom && task_is_dying())
+		goto nomem;
 
 	/*
 	 * keep retrying as long as the memcg oom killer is able to make
@@ -2640,14 +2710,10 @@
 	 */
 	oom_status = mem_cgroup_oom(mem_over_limit, gfp_mask,
 		       get_order(nr_pages * PAGE_SIZE));
-	switch (oom_status) {
-	case OOM_SUCCESS:
+	if (oom_status == OOM_SUCCESS) {
+		passed_oom = true;
 		nr_retries = MAX_RECLAIM_RETRIES;
 		goto retry;
-	case OOM_FAILED:
-		goto force;
-	default:
-		goto nomem;
 	}
 nomem:
 	if (!(gfp_mask & __GFP_NOFAIL))
@@ -2768,7 +2834,8 @@
  * Moreover, it should not come from DMA buffer and is not readily
  * reclaimable. So those GFP bits should be masked off.
  */
-#define OBJCGS_CLEAR_MASK	(__GFP_DMA | __GFP_RECLAIMABLE | __GFP_ACCOUNT)
+#define OBJCGS_CLEAR_MASK	(__GFP_DMA | __GFP_RECLAIMABLE | \
+				 __GFP_ACCOUNT | __GFP_NOFAIL)
 
 int memcg_alloc_page_obj_cgroups(struct page *page, struct kmem_cache *s,
 				 gfp_t gfp, bool new_page)
@@ -3518,8 +3585,7 @@
 	unsigned long val;
 
 	if (mem_cgroup_is_root(memcg)) {
-		/* mem_cgroup_threshold() calls here from irqsafe context */
-		cgroup_rstat_flush_irqsafe(memcg->css.cgroup);
+		mem_cgroup_flush_stats();
 		val = memcg_page_state(memcg, NR_FILE_PAGES) +
 			memcg_page_state(memcg, NR_ANON_MAPPED);
 		if (swap)
@@ -3819,6 +3885,10 @@
 {
 	struct mem_cgroup *memcg = mem_cgroup_from_css(css);
 
+	pr_warn_once("Cgroup memory moving (move_charge_at_immigrate) is deprecated. "
+		     "Please report your usecase to linux-mm@kvack.org if you "
+		     "depend on this functionality.\n");
+
 	if (val & ~MOVE_MASK)
 		return -EINVAL;
 
@@ -3900,7 +3970,7 @@
 	int nid;
 	struct mem_cgroup *memcg = mem_cgroup_from_seq(m);
 
-	cgroup_rstat_flush(memcg->css.cgroup);
+	mem_cgroup_flush_stats();
 
 	for (stat = stats; stat < stats + ARRAY_SIZE(stats); stat++) {
 		seq_printf(m, "%s=%lu", stat->name,
@@ -3972,7 +4042,7 @@
 
 	BUILD_BUG_ON(ARRAY_SIZE(memcg1_stat_names) != ARRAY_SIZE(memcg1_stats));
 
-	cgroup_rstat_flush(memcg->css.cgroup);
+	mem_cgroup_flush_stats();
 
 	for (i = 0; i < ARRAY_SIZE(memcg1_stats); i++) {
 		unsigned long nr;
@@ -4475,7 +4545,7 @@
 	struct mem_cgroup *memcg = mem_cgroup_from_css(wb->memcg_css);
 	struct mem_cgroup *parent;
 
-	cgroup_rstat_flush_irqsafe(memcg->css.cgroup);
+	mem_cgroup_flush_stats();
 
 	*pdirty = memcg_page_state(memcg, NR_FILE_DIRTY);
 	*pwriteback = memcg_page_state(memcg, NR_WRITEBACK);
@@ -4736,6 +4806,7 @@
 	unsigned int efd, cfd;
 	struct fd efile;
 	struct fd cfile;
+	struct dentry *cdentry;
 	const char *name;
 	char *endp;
 	int ret;
@@ -4748,9 +4819,12 @@
 	buf = endp + 1;
 
 	cfd = simple_strtoul(buf, &endp, 10);
-	if ((*endp != ' ') && (*endp != '\0'))
+	if (*endp == '\0')
+		buf = endp;
+	else if (*endp == ' ')
+		buf = endp + 1;
+	else
 		return -EINVAL;
-	buf = endp + 1;
 
 	event = kzalloc(sizeof(*event), GFP_KERNEL);
 	if (!event)
@@ -4787,6 +4861,16 @@
 		goto out_put_cfile;
 
 	/*
+	 * The control file must be a regular cgroup1 file. As a regular cgroup
+	 * file can't be renamed, it's safe to access its name afterwards.
+	 */
+	cdentry = cfile.file->f_path.dentry;
+	if (cdentry->d_sb->s_type != &cgroup_fs_type || !d_is_reg(cdentry)) {
+		ret = -EINVAL;
+		goto out_put_cfile;
+	}
+
+	/*
 	 * Determine the event callbacks and set them in @event.  This used
 	 * to be done via struct cftype but cgroup core no longer knows
 	 * about these events.  The following is crude but the whole thing
@@ -4794,7 +4878,7 @@
 	 *
 	 * DO NOT ADD NEW FILES.
 	 */
-	name = cfile.file->f_path.dentry->d_name.name;
+	name = cdentry->d_name.name;
 
 	if (!strcmp(name, "memory.usage_in_bytes")) {
 		event->register_event = mem_cgroup_usage_register_event;
@@ -4818,7 +4902,7 @@
 	 * automatically removed on cgroup destruction but the removal is
 	 * asynchronous, so take an extra ref on @css.
 	 */
-	cfile_css = css_tryget_online_from_dir(cfile.file->f_path.dentry->d_parent,
+	cfile_css = css_tryget_online_from_dir(cdentry->d_parent,
 					       &memory_cgrp_subsys);
 	ret = -EINVAL;
 	if (IS_ERR(cfile_css))
@@ -5011,11 +5095,28 @@
  */
 
 static DEFINE_IDR(mem_cgroup_idr);
+static DEFINE_SPINLOCK(memcg_idr_lock);
+
+static int mem_cgroup_alloc_id(void)
+{
+	int ret;
+
+	idr_preload(GFP_KERNEL);
+	spin_lock(&memcg_idr_lock);
+	ret = idr_alloc(&mem_cgroup_idr, NULL, 1, MEM_CGROUP_ID_MAX + 1,
+			GFP_NOWAIT);
+	spin_unlock(&memcg_idr_lock);
+	idr_preload_end();
+	return ret;
+}
 
 static void mem_cgroup_id_remove(struct mem_cgroup *memcg)
 {
 	if (memcg->id.id > 0) {
+		spin_lock(&memcg_idr_lock);
 		idr_remove(&mem_cgroup_idr, memcg->id.id);
+		spin_unlock(&memcg_idr_lock);
+
 		memcg->id.id = 0;
 	}
 }
@@ -5129,9 +5230,7 @@
 	if (!memcg)
 		return ERR_PTR(error);
 
-	memcg->id.id = idr_alloc(&mem_cgroup_idr, NULL,
-				 1, MEM_CGROUP_ID_MAX,
-				 GFP_KERNEL);
+	memcg->id.id = mem_cgroup_alloc_id();
 	if (memcg->id.id < 0) {
 		error = memcg->id.id;
 		goto fail;
@@ -5172,7 +5271,9 @@
 	INIT_LIST_HEAD(&memcg->deferred_split_queue.split_queue);
 	memcg->deferred_split_queue.split_queue_len = 0;
 #endif
+	spin_lock(&memcg_idr_lock);
 	idr_replace(&mem_cgroup_idr, memcg, memcg->id.id);
+	spin_unlock(&memcg_idr_lock);
 	return memcg;
 fail:
 	mem_cgroup_id_remove(memcg);
@@ -5341,21 +5442,6 @@
 	memcg_wb_domain_size_changed(memcg);
 }
 
-void mem_cgroup_flush_stats(void)
-{
-	if (!spin_trylock(&stats_flush_lock))
-		return;
-
-	cgroup_rstat_flush_irqsafe(root_mem_cgroup->css.cgroup);
-	spin_unlock(&stats_flush_lock);
-}
-
-static void flush_memcg_stats_dwork(struct work_struct *w)
-{
-	mem_cgroup_flush_stats();
-	queue_delayed_work(system_unbound_wq, &stats_flush_dwork, 2UL*HZ);
-}
-
 static void mem_cgroup_css_rstat_flush(struct cgroup_subsys_state *css, int cpu)
 {
 	struct mem_cgroup *memcg = mem_cgroup_from_css(css);
@@ -6373,7 +6459,7 @@
 	int i;
 	struct mem_cgroup *memcg = mem_cgroup_from_seq(m);
 
-	cgroup_rstat_flush(memcg->css.cgroup);
+	mem_cgroup_flush_stats();
 
 	for (i = 0; i < ARRAY_SIZE(memory_stats); i++) {
 		int nid;
@@ -7077,7 +7163,7 @@
 		if (!strcmp(token, "nokmem"))
 			cgroup_memory_nokmem = true;
 	}
-	return 0;
+	return 1;
 }
 __setup("cgroup.memory=", cgroup_memory);
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memfd.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memfd.c
@@ -31,20 +31,28 @@
 static void memfd_tag_pins(struct xa_state *xas)
 {
 	struct page *page;
-	unsigned int tagged = 0;
+	int latency = 0;
+	int cache_count;
 
 	lru_add_drain();
 
 	xas_lock_irq(xas);
 	xas_for_each(xas, page, ULONG_MAX) {
-		if (xa_is_value(page))
-			continue;
-		page = find_subpage(page, xas->xa_index);
-		if (page_count(page) - page_mapcount(page) > 1)
+		cache_count = 1;
+		if (!xa_is_value(page) &&
+		    PageTransHuge(page) && !PageHuge(page))
+			cache_count = HPAGE_PMD_NR;
+
+		if (!xa_is_value(page) &&
+		    page_count(page) - total_mapcount(page) != cache_count)
 			xas_set_mark(xas, MEMFD_TAG_PINNED);
+		if (cache_count != 1)
+			xas_set(xas, page->index + cache_count);
 
-		if (++tagged % XA_CHECK_SCHED)
+		latency += cache_count;
+		if (latency < XA_CHECK_SCHED)
 			continue;
+		latency = 0;
 
 		xas_pause(xas);
 		xas_unlock_irq(xas);
@@ -73,7 +81,8 @@
 
 	error = 0;
 	for (scan = 0; scan <= LAST_SCAN; scan++) {
-		unsigned int tagged = 0;
+		int latency = 0;
+		int cache_count;
 
 		if (!xas_marked(&xas, MEMFD_TAG_PINNED))
 			break;
@@ -87,10 +96,14 @@
 		xas_lock_irq(&xas);
 		xas_for_each_marked(&xas, page, ULONG_MAX, MEMFD_TAG_PINNED) {
 			bool clear = true;
-			if (xa_is_value(page))
-				continue;
-			page = find_subpage(page, xas.xa_index);
-			if (page_count(page) - page_mapcount(page) != 1) {
+
+			cache_count = 1;
+			if (!xa_is_value(page) &&
+			    PageTransHuge(page) && !PageHuge(page))
+				cache_count = HPAGE_PMD_NR;
+
+			if (!xa_is_value(page) && cache_count !=
+			    page_count(page) - total_mapcount(page)) {
 				/*
 				 * On the last scan, we clean up all those tags
 				 * we inserted; but make a note that we still
@@ -103,8 +116,11 @@
 			}
 			if (clear)
 				xas_clear_mark(&xas, MEMFD_TAG_PINNED);
-			if (++tagged % XA_CHECK_SCHED)
+
+			latency += cache_count;
+			if (latency < XA_CHECK_SCHED)
 				continue;
+			latency = 0;
 
 			xas_pause(&xas);
 			xas_unlock_irq(&xas);
@@ -314,7 +330,8 @@
 
 	if (flags & MFD_ALLOW_SEALING) {
 		file_seals = memfd_file_seals_ptr(file);
-		*file_seals &= ~F_SEAL_SEAL;
+		if (file_seals)
+			*file_seals &= ~F_SEAL_SEAL;
 	}
 
 	fd_install(fd, file);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memory-failure.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memory-failure.c
@@ -57,6 +57,7 @@
 #include <linux/ratelimit.h>
 #include <linux/page-isolation.h>
 #include <linux/pagewalk.h>
+#include <linux/shmem_fs.h>
 #include "internal.h"
 #include "ras/ras_event.h"
 
@@ -700,13 +701,18 @@
 	};
 	priv.tk.tsk = p;
 
+	if (!p->mm)
+		return -EFAULT;
+
 	mmap_read_lock(p->mm);
 	ret = walk_page_range(p->mm, 0, TASK_SIZE, &hwp_walk_ops,
 			      (void *)&priv);
 	if (ret == 1 && priv.tk.addr)
 		kill_proc(&priv.tk, pfn, flags);
+	else
+		ret = 0;
 	mmap_read_unlock(p->mm);
-	return ret ? -EFAULT : -EHWPOISON;
+	return ret > 0 ? -EHWPOISON : -EFAULT;
 }
 
 static const char *action_name[] = {
@@ -806,12 +812,44 @@
 	return ret;
 }
 
+struct page_state {
+	unsigned long mask;
+	unsigned long res;
+	enum mf_action_page_type type;
+
+	/* Callback ->action() has to unlock the relevant page inside it. */
+	int (*action)(struct page_state *ps, struct page *p);
+};
+
+/*
+ * Return true if page is still referenced by others, otherwise return
+ * false.
+ *
+ * The extra_pins is true when one extra refcount is expected.
+ */
+static bool has_extra_refcount(struct page_state *ps, struct page *p,
+			       bool extra_pins)
+{
+	int count = page_count(p) - 1;
+
+	if (extra_pins)
+		count -= 1;
+
+	if (count > 0) {
+		pr_err("Memory failure: %#lx: %s still referenced by %d users\n",
+		       page_to_pfn(p), action_page_types[ps->type], count);
+		return true;
+	}
+
+	return false;
+}
+
 /*
  * Error hit kernel page.
  * Do nothing, try to be lucky and not touch this instead. For a few cases we
  * could be more sophisticated.
  */
-static int me_kernel(struct page *p, unsigned long pfn)
+static int me_kernel(struct page_state *ps, struct page *p)
 {
 	unlock_page(p);
 	return MF_IGNORED;
@@ -820,9 +858,9 @@
 /*
  * Page in unknown state. Do nothing.
  */
-static int me_unknown(struct page *p, unsigned long pfn)
+static int me_unknown(struct page_state *ps, struct page *p)
 {
-	pr_err("Memory failure: %#lx: Unknown page state\n", pfn);
+	pr_err("Memory failure: %#lx: Unknown page state\n", page_to_pfn(p));
 	unlock_page(p);
 	return MF_FAILED;
 }
@@ -830,10 +868,11 @@
 /*
  * Clean (or cleaned) page cache page.
  */
-static int me_pagecache_clean(struct page *p, unsigned long pfn)
+static int me_pagecache_clean(struct page_state *ps, struct page *p)
 {
 	int ret;
 	struct address_space *mapping;
+	bool extra_pins;
 
 	delete_from_lru_cache(p);
 
@@ -863,13 +902,23 @@
 	}
 
 	/*
+	 * The shmem page is kept in page cache instead of truncating
+	 * so is expected to have an extra refcount after error-handling.
+	 */
+	extra_pins = shmem_mapping(mapping);
+
+	/*
 	 * Truncation is a bit tricky. Enable it per file system for now.
 	 *
 	 * Open: to take i_rwsem or not for this? Right now we don't.
 	 */
-	ret = truncate_error_page(p, pfn, mapping);
+	ret = truncate_error_page(p, page_to_pfn(p), mapping);
+	if (has_extra_refcount(ps, p, extra_pins))
+		ret = MF_FAILED;
+
 out:
 	unlock_page(p);
+
 	return ret;
 }
 
@@ -878,7 +927,7 @@
  * Issues: when the error hit a hole page the error is not properly
  * propagated.
  */
-static int me_pagecache_dirty(struct page *p, unsigned long pfn)
+static int me_pagecache_dirty(struct page_state *ps, struct page *p)
 {
 	struct address_space *mapping = page_mapping(p);
 
@@ -922,7 +971,7 @@
 		mapping_set_error(mapping, -EIO);
 	}
 
-	return me_pagecache_clean(p, pfn);
+	return me_pagecache_clean(ps, p);
 }
 
 /*
@@ -944,9 +993,10 @@
  * Clean swap cache pages can be directly isolated. A later page fault will
  * bring in the known good data from disk.
  */
-static int me_swapcache_dirty(struct page *p, unsigned long pfn)
+static int me_swapcache_dirty(struct page_state *ps, struct page *p)
 {
 	int ret;
+	bool extra_pins = false;
 
 	ClearPageDirty(p);
 	/* Trigger EIO in shmem: */
@@ -954,10 +1004,17 @@
 
 	ret = delete_from_lru_cache(p) ? MF_FAILED : MF_DELAYED;
 	unlock_page(p);
+
+	if (ret == MF_DELAYED)
+		extra_pins = true;
+
+	if (has_extra_refcount(ps, p, extra_pins))
+		ret = MF_FAILED;
+
 	return ret;
 }
 
-static int me_swapcache_clean(struct page *p, unsigned long pfn)
+static int me_swapcache_clean(struct page_state *ps, struct page *p)
 {
 	int ret;
 
@@ -965,6 +1022,10 @@
 
 	ret = delete_from_lru_cache(p) ? MF_FAILED : MF_RECOVERED;
 	unlock_page(p);
+
+	if (has_extra_refcount(ps, p, false))
+		ret = MF_FAILED;
+
 	return ret;
 }
 
@@ -974,18 +1035,21 @@
  * - Error on hugepage is contained in hugepage unit (not in raw page unit.)
  *   To narrow down kill region to one page, we need to break up pmd.
  */
-static int me_huge_page(struct page *p, unsigned long pfn)
+static int me_huge_page(struct page_state *ps, struct page *p)
 {
 	int res;
 	struct page *hpage = compound_head(p);
 	struct address_space *mapping;
+	bool extra_pins = false;
 
 	if (!PageHuge(hpage))
 		return MF_DELAYED;
 
 	mapping = page_mapping(hpage);
 	if (mapping) {
-		res = truncate_error_page(hpage, pfn, mapping);
+		res = truncate_error_page(hpage, page_to_pfn(p), mapping);
+		/* The page is kept in page cache. */
+		extra_pins = true;
 		unlock_page(hpage);
 	} else {
 		res = MF_FAILED;
@@ -1003,6 +1067,9 @@
 		}
 	}
 
+	if (has_extra_refcount(ps, p, extra_pins))
+		res = MF_FAILED;
+
 	return res;
 }
 
@@ -1028,14 +1095,7 @@
 #define slab		(1UL << PG_slab)
 #define reserved	(1UL << PG_reserved)
 
-static struct page_state {
-	unsigned long mask;
-	unsigned long res;
-	enum mf_action_page_type type;
-
-	/* Callback ->action() has to unlock the relevant page inside it. */
-	int (*action)(struct page *p, unsigned long pfn);
-} error_states[] = {
+static struct page_state error_states[] = {
 	{ reserved,	reserved,	MF_MSG_KERNEL,	me_kernel },
 	/*
 	 * free pages are specially detected outside this table:
@@ -1095,19 +1155,10 @@
 			unsigned long pfn)
 {
 	int result;
-	int count;
 
 	/* page p should be unlocked after returning from ps->action().  */
-	result = ps->action(p, pfn);
+	result = ps->action(ps, p);
 
-	count = page_count(p) - 1;
-	if (ps->action == me_swapcache_dirty && result == MF_DELAYED)
-		count--;
-	if (count > 0) {
-		pr_err("Memory failure: %#lx: %s still referenced by %d users\n",
-		       pfn, action_page_types[ps->type], count);
-		result = MF_FAILED;
-	}
 	action_result(pfn, ps->type, result);
 
 	/* Could do more checks here if page looks ok */
@@ -1215,7 +1266,7 @@
 	}
 out:
 	if (ret == -EIO)
-		dump_page(p, "hwpoison: unhandlable page");
+		pr_err("Memory failure: %#lx: unhandlable page.\n", page_to_pfn(p));
 
 	return ret;
 }
@@ -1280,7 +1331,7 @@
 	 * This check implies we don't kill processes if their pages
 	 * are in the swap cache early. Those are always late kills.
 	 */
-	if (!page_mapped(hpage))
+	if (!page_mapped(p))
 		return true;
 
 	if (PageKsm(p)) {
@@ -1346,10 +1397,10 @@
 		}
 	}
 
-	unmap_success = !page_mapped(hpage);
+	unmap_success = !page_mapped(p);
 	if (!unmap_success)
 		pr_err("Memory failure: %#lx: failed to unmap page (mapcount=%d)\n",
-		       pfn, page_mapcount(hpage));
+		       pfn, page_mapcount(p));
 
 	/*
 	 * try_to_unmap() might put mlocked page in lru cache, so call
@@ -1400,14 +1451,11 @@
 static int try_to_split_thp_page(struct page *page, const char *msg)
 {
 	lock_page(page);
-	if (!PageAnon(page) || unlikely(split_huge_page(page))) {
+	if (unlikely(split_huge_page(page))) {
 		unsigned long pfn = page_to_pfn(page);
 
 		unlock_page(page);
-		if (!PageAnon(page))
-			pr_info("%s: %#lx: non anonymous thp\n", msg, pfn);
-		else
-			pr_info("%s: %#lx: thp split failed\n", msg, pfn);
+		pr_info("%s: %#lx: thp split failed\n", msg, pfn);
 		put_page(page);
 		return -EBUSY;
 	}
@@ -1416,64 +1464,115 @@
 	return 0;
 }
 
-static int memory_failure_hugetlb(unsigned long pfn, int flags)
+/*
+ * Called from hugetlb code with hugetlb_lock held.
+ *
+ * Return values:
+ *   0             - free hugepage
+ *   1             - in-use hugepage
+ *   2             - not a hugepage
+ *   -EBUSY        - the hugepage is busy (try to retry)
+ *   -EHWPOISON    - the hugepage is already hwpoisoned
+ */
+int __get_huge_page_for_hwpoison(unsigned long pfn, int flags)
+{
+	struct page *page = pfn_to_page(pfn);
+	struct page *head = compound_head(page);
+	int ret = 2;	/* fallback to normal page handling */
+	bool count_increased = false;
+
+	if (!PageHeadHuge(head))
+		goto out;
+
+	if (flags & MF_COUNT_INCREASED) {
+		ret = 1;
+		count_increased = true;
+	} else if (HPageFreed(head) || HPageMigratable(head)) {
+		ret = get_page_unless_zero(head);
+		if (ret)
+			count_increased = true;
+	} else {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	if (TestSetPageHWPoison(head)) {
+		ret = -EHWPOISON;
+		goto out;
+	}
+
+	return ret;
+out:
+	if (count_increased)
+		put_page(head);
+	return ret;
+}
+
+#ifdef CONFIG_HUGETLB_PAGE
+/*
+ * Taking refcount of hugetlb pages needs extra care about race conditions
+ * with basic operations like hugepage allocation/free/demotion.
+ * So some of prechecks for hwpoison (pinning, and testing/setting
+ * PageHWPoison) should be done in single hugetlb_lock range.
+ */
+static int try_memory_failure_hugetlb(unsigned long pfn, int flags, int *hugetlb)
 {
-	struct page *p = pfn_to_page(pfn);
-	struct page *head = compound_head(p);
 	int res;
+	struct page *p = pfn_to_page(pfn);
+	struct page *head;
 	unsigned long page_flags;
+	bool retry = true;
 
-	if (TestSetPageHWPoison(head)) {
-		pr_err("Memory failure: %#lx: already hardware poisoned\n",
-		       pfn);
-		res = -EHWPOISON;
-		if (flags & MF_ACTION_REQUIRED)
+	*hugetlb = 1;
+retry:
+	res = get_huge_page_for_hwpoison(pfn, flags);
+	if (res == 2) { /* fallback to normal page handling */
+		*hugetlb = 0;
+		return 0;
+	} else if (res == -EHWPOISON) {
+		pr_err("Memory failure: %#lx: already hardware poisoned\n", pfn);
+		if (flags & MF_ACTION_REQUIRED) {
+			head = compound_head(p);
 			res = kill_accessing_process(current, page_to_pfn(head), flags);
+		}
+		return res;
+	} else if (res == -EBUSY) {
+		if (retry) {
+			retry = false;
+			goto retry;
+		}
+		action_result(pfn, MF_MSG_UNKNOWN, MF_IGNORED);
 		return res;
 	}
 
-	num_poisoned_pages_inc();
+	head = compound_head(p);
+	lock_page(head);
 
-	if (!(flags & MF_COUNT_INCREASED)) {
-		res = get_hwpoison_page(p, flags);
-		if (!res) {
-			/*
-			 * Check "filter hit" and "race with other subpage."
-			 */
-			lock_page(head);
-			if (PageHWPoison(head)) {
-				if ((hwpoison_filter(p) && TestClearPageHWPoison(p))
-				    || (p != head && TestSetPageHWPoison(head))) {
-					num_poisoned_pages_dec();
-					unlock_page(head);
-					return 0;
-				}
-			}
-			unlock_page(head);
-			res = MF_FAILED;
-			if (__page_handle_poison(p)) {
-				page_ref_inc(p);
-				res = MF_RECOVERED;
-			}
-			action_result(pfn, MF_MSG_FREE_HUGE, res);
-			return res == MF_RECOVERED ? 0 : -EBUSY;
-		} else if (res < 0) {
-			action_result(pfn, MF_MSG_UNKNOWN, MF_IGNORED);
-			return -EBUSY;
-		}
+	if (hwpoison_filter(p)) {
+		ClearPageHWPoison(head);
+		res = -EOPNOTSUPP;
+		goto out;
 	}
 
-	lock_page(head);
-	page_flags = head->flags;
+	num_poisoned_pages_inc();
 
-	if (!PageHWPoison(head)) {
-		pr_err("Memory failure: %#lx: just unpoisoned\n", pfn);
-		num_poisoned_pages_dec();
+	/*
+	 * Handling free hugepage.  The possible race with hugepage allocation
+	 * or demotion can be prevented by PageHWPoison flag.
+	 */
+	if (res == 0) {
 		unlock_page(head);
-		put_page(head);
-		return 0;
+		res = MF_FAILED;
+		if (__page_handle_poison(p)) {
+			page_ref_inc(p);
+			res = MF_RECOVERED;
+		}
+		action_result(pfn, MF_MSG_FREE_HUGE, res);
+		return res == MF_RECOVERED ? 0 : -EBUSY;
 	}
 
+	page_flags = head->flags;
+
 	/*
 	 * TODO: hwpoison for pud-sized hugetlb doesn't work right now, so
 	 * simply disable it. In order to make it work properly, we need
@@ -1500,6 +1599,12 @@
 	unlock_page(head);
 	return res;
 }
+#else
+static inline int try_memory_failure_hugetlb(unsigned long pfn, int flags, int *hugetlb)
+{
+	return 0;
+}
+#endif
 
 static int memory_failure_dev_pagemap(unsigned long pfn, int flags,
 		struct dev_pagemap *pgmap)
@@ -1536,7 +1641,7 @@
 		goto out;
 
 	if (hwpoison_filter(page)) {
-		rc = 0;
+		rc = -EOPNOTSUPP;
 		goto unlock;
 	}
 
@@ -1587,6 +1692,8 @@
 	return rc;
 }
 
+static DEFINE_MUTEX(mf_mutex);
+
 /**
  * memory_failure - Handle memory failure of a page.
  * @pfn: Page Number of the corrupted page
@@ -1603,6 +1710,10 @@
  *
  * Must run in process context (e.g. a work queue) with interrupts
  * enabled and no spinlocks hold.
+ *
+ * Return: 0 for successfully handled the memory error,
+ *         -EOPNOTSUPP for memory_filter() filtered the error event,
+ *         < 0(except -EOPNOTSUPP) on failure.
  */
 int memory_failure(unsigned long pfn, int flags)
 {
@@ -1613,7 +1724,7 @@
 	int res = 0;
 	unsigned long page_flags;
 	bool retry = true;
-	static DEFINE_MUTEX(mf_mutex);
+	int hugetlb = 0;
 
 	if (!sysctl_memory_failure_recovery)
 		panic("Memory failure on page %lx", pfn);
@@ -1634,10 +1745,9 @@
 	mutex_lock(&mf_mutex);
 
 try_again:
-	if (PageHuge(p)) {
-		res = memory_failure_hugetlb(pfn, flags);
+	res = try_memory_failure_hugetlb(pfn, flags, &hugetlb);
+	if (hugetlb)
 		goto unlock_mutex;
-	}
 
 	if (TestSetPageHWPoison(p)) {
 		pr_err("Memory failure: %#lx: already hardware poisoned\n",
@@ -1747,21 +1857,12 @@
 	 */
 	page_flags = p->flags;
 
-	/*
-	 * unpoison always clear PG_hwpoison inside page lock
-	 */
-	if (!PageHWPoison(p)) {
-		pr_err("Memory failure: %#lx: just unpoisoned\n", pfn);
-		num_poisoned_pages_dec();
-		unlock_page(p);
-		put_page(p);
-		goto unlock_mutex;
-	}
 	if (hwpoison_filter(p)) {
 		if (TestClearPageHWPoison(p))
 			num_poisoned_pages_dec();
 		unlock_page(p);
 		put_page(p);
+		res = -EOPNOTSUPP;
 		goto unlock_mutex;
 	}
 
@@ -1937,6 +2038,7 @@
 	struct page *page;
 	struct page *p;
 	int freeit = 0;
+	int ret = 0;
 	unsigned long flags = 0;
 	static DEFINE_RATELIMIT_STATE(unpoison_rs, DEFAULT_RATELIMIT_INTERVAL,
 					DEFAULT_RATELIMIT_BURST);
@@ -1947,39 +2049,37 @@
 	p = pfn_to_page(pfn);
 	page = compound_head(p);
 
+	mutex_lock(&mf_mutex);
+
+	if (is_huge_zero_page(page)) {
+		unpoison_pr_info("Unpoison: huge zero page is not supported %#lx\n",
+				 pfn, &unpoison_rs);
+		ret = -EOPNOTSUPP;
+		goto unlock_mutex;
+	}
+
 	if (!PageHWPoison(p)) {
 		unpoison_pr_info("Unpoison: Page was already unpoisoned %#lx\n",
 				 pfn, &unpoison_rs);
-		return 0;
+		goto unlock_mutex;
 	}
 
 	if (page_count(page) > 1) {
 		unpoison_pr_info("Unpoison: Someone grabs the hwpoison page %#lx\n",
 				 pfn, &unpoison_rs);
-		return 0;
+		goto unlock_mutex;
 	}
 
 	if (page_mapped(page)) {
 		unpoison_pr_info("Unpoison: Someone maps the hwpoison page %#lx\n",
 				 pfn, &unpoison_rs);
-		return 0;
+		goto unlock_mutex;
 	}
 
 	if (page_mapping(page)) {
 		unpoison_pr_info("Unpoison: the hwpoison page has non-NULL mapping %#lx\n",
 				 pfn, &unpoison_rs);
-		return 0;
-	}
-
-	/*
-	 * unpoison_memory() can encounter thp only when the thp is being
-	 * worked by memory_failure() and the page lock is not held yet.
-	 * In such case, we yield to memory_failure() and make unpoison fail.
-	 */
-	if (!PageHuge(page) && PageTransHuge(page)) {
-		unpoison_pr_info("Unpoison: Memory failure is now running on %#lx\n",
-				 pfn, &unpoison_rs);
-		return 0;
+		goto unlock_mutex;
 	}
 
 	if (!get_hwpoison_page(p, flags)) {
@@ -1987,29 +2087,23 @@
 			num_poisoned_pages_dec();
 		unpoison_pr_info("Unpoison: Software-unpoisoned free page %#lx\n",
 				 pfn, &unpoison_rs);
-		return 0;
+		goto unlock_mutex;
 	}
 
-	lock_page(page);
-	/*
-	 * This test is racy because PG_hwpoison is set outside of page lock.
-	 * That's acceptable because that won't trigger kernel panic. Instead,
-	 * the PG_hwpoison page will be caught and isolated on the entrance to
-	 * the free buddy page pool.
-	 */
 	if (TestClearPageHWPoison(page)) {
 		unpoison_pr_info("Unpoison: Software-unpoisoned page %#lx\n",
 				 pfn, &unpoison_rs);
 		num_poisoned_pages_dec();
 		freeit = 1;
 	}
-	unlock_page(page);
 
 	put_page(page);
 	if (freeit && !(pfn == my_zero_pfn(0) && page_count(p) == 1))
 		put_page(page);
 
-	return 0;
+unlock_mutex:
+	mutex_unlock(&mf_mutex);
+	return ret;
 }
 EXPORT_SYMBOL(unpoison_memory);
 
@@ -2019,7 +2113,7 @@
 	bool lru = PageLRU(page);
 
 	if (PageHuge(page)) {
-		isolated = isolate_huge_page(page, pagelist);
+		isolated = !isolate_hugetlb(page, pagelist);
 	} else {
 		if (lru)
 			isolated = !isolate_lru_page(page);
@@ -2132,16 +2226,6 @@
 	return __soft_offline_page(page);
 }
 
-static int soft_offline_free_page(struct page *page)
-{
-	int rc = 0;
-
-	if (!page_handle_poison(page, true, false))
-		rc = -EBUSY;
-
-	return rc;
-}
-
 static void put_ref_page(struct page *page)
 {
 	if (page)
@@ -2190,9 +2274,12 @@
 		return -EIO;
 	}
 
+	mutex_lock(&mf_mutex);
+
 	if (PageHWPoison(page)) {
 		pr_info("%s: %#lx page already poisoned\n", __func__, pfn);
 		put_ref_page(ref_page);
+		mutex_unlock(&mf_mutex);
 		return 0;
 	}
 
@@ -2204,11 +2291,17 @@
 	if (ret > 0) {
 		ret = soft_offline_in_use_page(page);
 	} else if (ret == 0) {
-		if (soft_offline_free_page(page) && try_again) {
-			try_again = false;
-			goto retry;
+		if (!page_handle_poison(page, true, false)) {
+			if (try_again) {
+				try_again = false;
+				flags &= ~MF_COUNT_INCREASED;
+				goto retry;
+			}
+			ret = -EBUSY;
 		}
 	}
 
+	mutex_unlock(&mf_mutex);
+
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memory.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memory.c
@@ -903,6 +903,17 @@
 	if (likely(!page_needs_cow_for_dma(src_vma, page)))
 		return 1;
 
+	/*
+	 * The vma->anon_vma of the child process may be NULL
+	 * because the entire vma does not contain anonymous pages.
+	 * A BUG will occur when the copy_present_page() passes
+	 * a copy of a non-anonymous page of that vma to the
+	 * page_add_new_anon_rmap() to set up new anonymous rmap.
+	 * Return 1 if the page is not an anonymous page.
+	 */
+	if (!PageAnon(page))
+		return 1;
+
 	new_page = *prealloc;
 	if (!new_page)
 		return -EAGAIN;
@@ -1301,6 +1312,17 @@
 	return ret;
 }
 
+/* Whether we should zap all COWed (private) pages too */
+static inline bool should_zap_cows(struct zap_details *details)
+{
+	/* By default, zap all pages */
+	if (!details)
+		return true;
+
+	/* Or, we zap COWed pages only if the caller wants to */
+	return !details->check_mapping;
+}
+
 static unsigned long zap_pte_range(struct mmu_gather *tlb,
 				struct vm_area_struct *vma, pmd_t *pmd,
 				unsigned long addr, unsigned long end,
@@ -1396,16 +1418,18 @@
 			continue;
 		}
 
-		/* If details->check_mapping, we leave swap entries. */
-		if (unlikely(details))
-			continue;
-
-		if (!non_swap_entry(entry))
+		if (!non_swap_entry(entry)) {
+			/* Genuine swap entry, hence a private anon page */
+			if (!should_zap_cows(details))
+				continue;
 			rss[MM_SWAPENTS]--;
-		else if (is_migration_entry(entry)) {
+		} else if (is_migration_entry(entry)) {
 			struct page *page;
 
 			page = pfn_swap_entry_to_page(entry);
+			if (details && details->check_mapping &&
+			    details->check_mapping != page_rmapping(page))
+				continue;
 			rss[mm_counter(page)]--;
 		}
 		if (unlikely(!free_swap_and_cache(entry)))
@@ -1655,6 +1679,7 @@
 	mmu_notifier_invalidate_range_end(&range);
 	tlb_finish_mmu(&tlb);
 }
+EXPORT_SYMBOL(zap_page_range);
 
 /**
  * zap_page_range_single - remove user pages in a given range
@@ -2367,11 +2392,7 @@
 	return 0;
 }
 
-/*
- * Variant of remap_pfn_range that does not call track_pfn_remap.  The caller
- * must have pre-validated the caching bits of the pgprot_t.
- */
-int remap_pfn_range_notrack(struct vm_area_struct *vma, unsigned long addr,
+static int remap_pfn_range_internal(struct vm_area_struct *vma, unsigned long addr,
 		unsigned long pfn, unsigned long size, pgprot_t prot)
 {
 	pgd_t *pgd;
@@ -2424,6 +2445,27 @@
 	return 0;
 }
 
+/*
+ * Variant of remap_pfn_range that does not call track_pfn_remap.  The caller
+ * must have pre-validated the caching bits of the pgprot_t.
+ */
+int remap_pfn_range_notrack(struct vm_area_struct *vma, unsigned long addr,
+		unsigned long pfn, unsigned long size, pgprot_t prot)
+{
+	int error = remap_pfn_range_internal(vma, addr, pfn, size, prot);
+
+	if (!error)
+		return 0;
+
+	/*
+	 * A partial pfn range mapping is dangerous: it does not
+	 * maintain page reference counts, and callers may free
+	 * pages due to the error. So zap it early.
+	 */
+	zap_page_range_single(vma, addr, size, NULL);
+	return error;
+}
+
 /**
  * remap_pfn_range - remap kernel memory to userspace
  * @vma: user vma to map to
@@ -2672,8 +2714,10 @@
 		next = pgd_addr_end(addr, end);
 		if (pgd_none(*pgd) && !create)
 			continue;
-		if (WARN_ON_ONCE(pgd_leaf(*pgd)))
-			return -EINVAL;
+		if (WARN_ON_ONCE(pgd_leaf(*pgd))) {
+			err = -EINVAL;
+			break;
+		}
 		if (!pgd_none(*pgd) && WARN_ON_ONCE(pgd_bad(*pgd))) {
 			if (!create)
 				continue;
@@ -2740,10 +2784,16 @@
 	return same;
 }
 
-static inline bool cow_user_page(struct page *dst, struct page *src,
-				 struct vm_fault *vmf)
+/*
+ * Return:
+ *	0:		copied succeeded
+ *	-EHWPOISON:	copy failed due to hwpoison in source page
+ *	-EAGAIN:	copied failed (some other reason)
+ */
+static inline int cow_user_page(struct page *dst, struct page *src,
+				      struct vm_fault *vmf)
 {
-	bool ret;
+	int ret;
 	void *kaddr;
 	void __user *uaddr;
 	bool locked = false;
@@ -2752,8 +2802,11 @@
 	unsigned long addr = vmf->address;
 
 	if (likely(src)) {
-		copy_user_highpage(dst, src, addr, vma);
-		return true;
+		if (copy_mc_user_highpage(dst, src, addr, vma)) {
+			memory_failure_queue(page_to_pfn(src), 0);
+			return -EHWPOISON;
+		}
+		return 0;
 	}
 
 	/*
@@ -2780,7 +2833,7 @@
 			 * and update local tlb only
 			 */
 			update_mmu_tlb(vma, addr, vmf->pte);
-			ret = false;
+			ret = -EAGAIN;
 			goto pte_unlock;
 		}
 
@@ -2805,7 +2858,7 @@
 		if (!likely(pte_same(*vmf->pte, vmf->orig_pte))) {
 			/* The PTE changed under us, update local tlb */
 			update_mmu_tlb(vma, addr, vmf->pte);
-			ret = false;
+			ret = -EAGAIN;
 			goto pte_unlock;
 		}
 
@@ -2824,7 +2877,7 @@
 		}
 	}
 
-	ret = true;
+	ret = 0;
 
 pte_unlock:
 	if (locked)
@@ -2990,6 +3043,7 @@
 	pte_t entry;
 	int page_copied = 0;
 	struct mmu_notifier_range range;
+	int ret;
 
 	if (unlikely(anon_vma_prepare(vma)))
 		goto oom;
@@ -3005,17 +3059,20 @@
 		if (!new_page)
 			goto oom;
 
-		if (!cow_user_page(new_page, old_page, vmf)) {
+		ret = cow_user_page(new_page, old_page, vmf);
+		if (ret) {
 			/*
 			 * COW failed, if the fault was solved by other,
 			 * it's fine. If not, userspace would re-fault on
 			 * the same address and we will handle the fault
 			 * from the second attempt.
+			 * The -EHWPOISON case will not be retried.
 			 */
 			put_page(new_page);
 			if (old_page)
 				put_page(old_page);
-			return 0;
+
+			return ret == -EHWPOISON ? VM_FAULT_HWPOISON : 0;
 		}
 	}
 
@@ -3425,8 +3482,8 @@
 void unmap_mapping_range(struct address_space *mapping,
 		loff_t const holebegin, loff_t const holelen, int even_cows)
 {
-	pgoff_t hba = holebegin >> PAGE_SHIFT;
-	pgoff_t hlen = (holelen + PAGE_SIZE - 1) >> PAGE_SHIFT;
+	pgoff_t hba = (pgoff_t)(holebegin) >> PAGE_SHIFT;
+	pgoff_t hlen = ((pgoff_t)(holelen) + PAGE_SIZE - 1) >> PAGE_SHIFT;
 
 	/* Check for overflow. */
 	if (sizeof(holelen) > sizeof(hlen)) {
@@ -3449,8 +3506,21 @@
 	struct vm_area_struct *vma = vmf->vma;
 	struct mmu_notifier_range range;
 
-	if (!lock_page_or_retry(page, vma->vm_mm, vmf->flags))
+	/*
+	 * We need a reference to lock the page because we don't hold
+	 * the PTL so a racing thread can remove the device-exclusive
+	 * entry and unmap it. If the page is free the entry must
+	 * have been removed already. If it happens to have already
+	 * been re-allocated after being freed all we do is lock and
+	 * unlock it.
+	 */
+	if (!get_page_unless_zero(page))
+		return 0;
+
+	if (!lock_page_or_retry(page, vma->vm_mm, vmf->flags)) {
+		put_page(page);
 		return VM_FAULT_RETRY;
+	}
 	mmu_notifier_range_init_owner(&range, MMU_NOTIFY_EXCLUSIVE, 0, vma,
 				vma->vm_mm, vmf->address & PAGE_MASK,
 				(vmf->address & PAGE_MASK) + PAGE_SIZE, NULL);
@@ -3463,6 +3533,7 @@
 
 	pte_unmap_unlock(vmf->pte, vmf->ptl);
 	unlock_page(page);
+	put_page(page);
 
 	mmu_notifier_invalidate_range_end(&range);
 	return 0;
@@ -3861,11 +3932,20 @@
 		return ret;
 
 	if (unlikely(PageHWPoison(vmf->page))) {
-		if (ret & VM_FAULT_LOCKED)
-			unlock_page(vmf->page);
-		put_page(vmf->page);
+		struct page *page = vmf->page;
+		vm_fault_t poisonret = VM_FAULT_HWPOISON;
+		if (ret & VM_FAULT_LOCKED) {
+			if (page_mapped(page))
+				unmap_mapping_pages(page_mapping(page),
+						    page->index, 1, false);
+			/* Retry if a clean page was removed from the cache. */
+			if (invalidate_inode_page(page))
+				poisonret = VM_FAULT_NOPAGE;
+			unlock_page(page);
+		}
+		put_page(page);
 		vmf->page = NULL;
-		return VM_FAULT_HWPOISON;
+		return poisonret;
 	}
 
 	if (unlikely(!(ret & VM_FAULT_LOCKED)))
@@ -4049,9 +4129,12 @@
 		}
 	}
 
-	/* See comment in handle_pte_fault() */
+	/*
+	 * See comment in handle_pte_fault() for how this scenario happens, we
+	 * need to return NOPAGE so that we drop this page.
+	 */
 	if (pmd_devmap_trans_unstable(vmf->pmd))
-		return 0;
+		return VM_FAULT_NOPAGE;
 
 	vmf->pte = pte_offset_map_lock(vma->vm_mm, vmf->pmd,
 				      vmf->address, &vmf->ptl);
@@ -4355,7 +4438,7 @@
 	spin_lock(vmf->ptl);
 	if (unlikely(!pte_same(*vmf->pte, vmf->orig_pte))) {
 		pte_unmap_unlock(vmf->pte, vmf->ptl);
-		goto out;
+		return 0;
 	}
 
 	/* Get the normal PTE  */
@@ -4402,21 +4485,17 @@
 	if (migrate_misplaced_page(page, vma, target_nid)) {
 		page_nid = target_nid;
 		flags |= TNF_MIGRATED;
-	} else {
-		flags |= TNF_MIGRATE_FAIL;
-		vmf->pte = pte_offset_map(vmf->pmd, vmf->address);
-		spin_lock(vmf->ptl);
-		if (unlikely(!pte_same(*vmf->pte, vmf->orig_pte))) {
-			pte_unmap_unlock(vmf->pte, vmf->ptl);
-			goto out;
-		}
-		goto out_map;
+		task_numa_fault(last_cpupid, page_nid, 1, flags);
+		return 0;
 	}
 
-out:
-	if (page_nid != NUMA_NO_NODE)
-		task_numa_fault(last_cpupid, page_nid, 1, flags);
-	return 0;
+	flags |= TNF_MIGRATE_FAIL;
+	vmf->pte = pte_offset_map(vmf->pmd, vmf->address);
+	spin_lock(vmf->ptl);
+	if (unlikely(!pte_same(*vmf->pte, vmf->orig_pte))) {
+		pte_unmap_unlock(vmf->pte, vmf->ptl);
+		return 0;
+	}
 out_map:
 	/*
 	 * Make it present again, depending on how arch implements
@@ -4430,7 +4509,10 @@
 	ptep_modify_prot_commit(vma, vmf->address, vmf->pte, old_pte, pte);
 	update_mmu_cache(vma, vmf->address, vmf->pte);
 	pte_unmap_unlock(vmf->pte, vmf->ptl);
-	goto out;
+
+	if (page_nid != NUMA_NO_NODE)
+		task_numa_fault(last_cpupid, page_nid, 1, flags);
+	return 0;
 }
 
 static inline vm_fault_t create_huge_pmd(struct vm_fault *vmf)
@@ -4469,6 +4551,19 @@
 	defined(CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD)
 	/* No support for anonymous transparent PUD pages yet */
 	if (vma_is_anonymous(vmf->vma))
+		return VM_FAULT_FALLBACK;
+	if (vmf->vma->vm_ops->huge_fault)
+		return vmf->vma->vm_ops->huge_fault(vmf, PE_SIZE_PUD);
+#endif /* CONFIG_TRANSPARENT_HUGEPAGE */
+	return VM_FAULT_FALLBACK;
+}
+
+static vm_fault_t wp_huge_pud(struct vm_fault *vmf, pud_t orig_pud)
+{
+#if defined(CONFIG_TRANSPARENT_HUGEPAGE) &&			\
+	defined(CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD)
+	/* No support for anonymous transparent PUD pages yet */
+	if (vma_is_anonymous(vmf->vma))
 		goto split;
 	if (vmf->vma->vm_ops->huge_fault) {
 		vm_fault_t ret = vmf->vma->vm_ops->huge_fault(vmf, PE_SIZE_PUD);
@@ -4479,19 +4574,7 @@
 split:
 	/* COW or write-notify not handled on PUD level: split pud.*/
 	__split_huge_pud(vmf->vma, vmf->pud, vmf->address);
-#endif /* CONFIG_TRANSPARENT_HUGEPAGE */
-	return VM_FAULT_FALLBACK;
-}
-
-static vm_fault_t wp_huge_pud(struct vm_fault *vmf, pud_t orig_pud)
-{
-#ifdef CONFIG_TRANSPARENT_HUGEPAGE
-	/* No support for anonymous transparent PUD pages yet */
-	if (vma_is_anonymous(vmf->vma))
-		return VM_FAULT_FALLBACK;
-	if (vmf->vma->vm_ops->huge_fault)
-		return vmf->vma->vm_ops->huge_fault(vmf, PE_SIZE_PUD);
-#endif /* CONFIG_TRANSPARENT_HUGEPAGE */
+#endif /* CONFIG_TRANSPARENT_HUGEPAGE && CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD */
 	return VM_FAULT_FALLBACK;
 }
 
@@ -5033,6 +5116,10 @@
 		goto out;
 	pte = *ptep;
 
+	/* Never return PFNs of anon folios in COW mappings. */
+	if (vm_normal_page(vma, address, pte))
+		goto unlock;
+
 	if ((flags & FOLL_WRITE) && !pte_write(pte))
 		goto unlock;
 
@@ -5445,6 +5532,8 @@
 		if (rc)
 			break;
 
+		flush_dcache_page(subpage);
+
 		cond_resched();
 	}
 	return ret_val;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memory_hotplug.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memory_hotplug.c
@@ -1384,8 +1384,11 @@
 
 	mem_hotplug_begin();
 
-	if (IS_ENABLED(CONFIG_ARCH_KEEP_MEMBLOCK))
-		memblock_add_node(start, size, nid);
+	if (IS_ENABLED(CONFIG_ARCH_KEEP_MEMBLOCK)) {
+		ret = memblock_add_node(start, size, nid, MEMBLOCK_NONE);
+		if (ret)
+			goto error_mem_hotplug_end;
+	}
 
 	ret = __try_online_node(nid, false);
 	if (ret < 0)
@@ -1458,6 +1461,7 @@
 		rollback_node_hotadd(nid);
 	if (IS_ENABLED(CONFIG_ARCH_KEEP_MEMBLOCK))
 		memblock_remove(start, size);
+error_mem_hotplug_end:
 	mem_hotplug_done();
 	return ret;
 }
@@ -1677,7 +1681,7 @@
 		 */
 		if (HPageMigratable(head))
 			goto found;
-		skip = compound_nr(head) - (page - head);
+		skip = compound_nr(head) - (pfn - page_to_pfn(head));
 		pfn += skip - 1;
 	}
 	return -ENOENT;
@@ -1704,7 +1708,7 @@
 
 		if (PageHuge(page)) {
 			pfn = page_to_pfn(head) + compound_nr(head) - 1;
-			isolate_huge_page(head, &source);
+			isolate_hugetlb(head, &source);
 			continue;
 		} else if (PageTransHuge(page))
 			pfn = page_to_pfn(head) + thp_nr_pages(page) - 1;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mempolicy.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mempolicy.c
@@ -347,7 +347,7 @@
  */
 static void mpol_rebind_policy(struct mempolicy *pol, const nodemask_t *newmask)
 {
-	if (!pol)
+	if (!pol || pol->mode == MPOL_LOCAL)
 		return;
 	if (!mpol_store_user_nodemask(pol) &&
 	    nodes_equal(pol->w.cpuset_mems_allowed, *newmask))
@@ -603,8 +603,9 @@
 
 	/* With MPOL_MF_MOVE, we migrate only unshared hugepage. */
 	if (flags & (MPOL_MF_MOVE_ALL) ||
-	    (flags & MPOL_MF_MOVE && page_mapcount(page) == 1)) {
-		if (!isolate_huge_page(page, qp->pagelist) &&
+	    (flags & MPOL_MF_MOVE && page_mapcount(page) == 1 &&
+	     !hugetlb_pmd_shared(pte))) {
+		if (isolate_hugetlb(page, qp->pagelist) &&
 			(flags & MPOL_MF_STRICT))
 			/*
 			 * Failed to isolate page but allow migrating pages
@@ -783,7 +784,6 @@
 static int mbind_range(struct mm_struct *mm, unsigned long start,
 		       unsigned long end, struct mempolicy *new_pol)
 {
-	struct vm_area_struct *next;
 	struct vm_area_struct *prev;
 	struct vm_area_struct *vma;
 	int err = 0;
@@ -798,8 +798,7 @@
 	if (start > vma->vm_start)
 		prev = vma;
 
-	for (; vma && vma->vm_start < end; prev = vma, vma = next) {
-		next = vma->vm_next;
+	for (; vma && vma->vm_start < end; prev = vma, vma = vma->vm_next) {
 		vmstart = max(start, vma->vm_start);
 		vmend   = min(end, vma->vm_end);
 
@@ -813,10 +812,6 @@
 				 new_pol, vma->vm_userfaultfd_ctx);
 		if (prev) {
 			vma = prev;
-			next = vma->vm_next;
-			if (mpol_equal(vma_policy(vma), new_pol))
-				continue;
-			/* vma_merge() joined vma && vma->next, case 8 */
 			goto replace;
 		}
 		if (vma->vm_start != vmstart) {
@@ -1395,7 +1390,7 @@
 		unsigned long bits = min_t(unsigned long, maxnode, BITS_PER_LONG);
 		unsigned long t;
 
-		if (get_bitmap(&t, &nmask[maxnode / BITS_PER_LONG], bits))
+		if (get_bitmap(&t, &nmask[(maxnode - 1) / BITS_PER_LONG], bits))
 			return -EFAULT;
 
 		if (maxnode - bits >= MAX_NUMNODES) {
@@ -2140,8 +2135,7 @@
 			 * memory with both reclaim and compact as well.
 			 */
 			if (!page && (gfp & __GFP_DIRECT_RECLAIM))
-				page = __alloc_pages_node(hpage_node,
-								gfp, order);
+				page = __alloc_pages(gfp, order, hpage_node, nmask);
 
 			goto out;
 		}
@@ -2568,6 +2562,7 @@
 	mpol_new = kmem_cache_alloc(policy_cache, GFP_KERNEL);
 	if (!mpol_new)
 		goto err_out;
+	atomic_set(&mpol_new->refcnt, 1);
 	goto restart;
 }
 
@@ -2926,8 +2921,9 @@
  * @pol:  pointer to mempolicy to be formatted
  *
  * Convert @pol into a string.  If @buffer is too short, truncate the string.
- * Recommend a @maxlen of at least 32 for the longest mode, "interleave", the
- * longest flag, "relative", and to display at least a few node ids.
+ * Recommend a @maxlen of at least 51 for the longest mode, "weighted
+ * interleave", plus the longest flag flags, "relative|balancing", and to
+ * display at least a few node ids.
  */
 void mpol_to_str(char *buffer, int maxlen, struct mempolicy *pol)
 {
@@ -2936,7 +2932,10 @@
 	unsigned short mode = MPOL_DEFAULT;
 	unsigned short flags = 0;
 
-	if (pol && pol != &default_policy && !(pol->flags & MPOL_F_MORON)) {
+	if (pol &&
+	    pol != &default_policy &&
+	    !(pol >= &preferred_node_policy[0] &&
+	      pol <= &preferred_node_policy[ARRAY_SIZE(preferred_node_policy) - 1])) {
 		mode = pol->mode;
 		flags = pol->flags;
 	}
@@ -2963,12 +2962,18 @@
 		p += snprintf(p, buffer + maxlen - p, "=");
 
 		/*
-		 * Currently, the only defined flags are mutually exclusive
+		 * Static and relative are mutually exclusive.
 		 */
 		if (flags & MPOL_F_STATIC_NODES)
 			p += snprintf(p, buffer + maxlen - p, "static");
 		else if (flags & MPOL_F_RELATIVE_NODES)
 			p += snprintf(p, buffer + maxlen - p, "relative");
+
+		if (flags & MPOL_F_NUMA_BALANCING) {
+			if (!is_power_of_2(flags & MPOL_MODE_FLAGS))
+				p += snprintf(p, buffer + maxlen - p, "|");
+			p += snprintf(p, buffer + maxlen - p, "balancing");
+		}
 	}
 
 	if (!nodes_empty(nodes))
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memremap.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memremap.c
@@ -112,30 +112,6 @@
 #define for_each_device_pfn(pfn, map, i) \
 	for (pfn = pfn_first(map, i); pfn < pfn_end(map, i); pfn = pfn_next(pfn))
 
-static void dev_pagemap_kill(struct dev_pagemap *pgmap)
-{
-	if (pgmap->ops && pgmap->ops->kill)
-		pgmap->ops->kill(pgmap);
-	else
-		percpu_ref_kill(pgmap->ref);
-}
-
-static void dev_pagemap_cleanup(struct dev_pagemap *pgmap)
-{
-	if (pgmap->ops && pgmap->ops->cleanup) {
-		pgmap->ops->cleanup(pgmap);
-	} else {
-		wait_for_completion(&pgmap->done);
-		percpu_ref_exit(pgmap->ref);
-	}
-	/*
-	 * Undo the pgmap ref assignment for the internal case as the
-	 * caller may re-enable the same pgmap.
-	 */
-	if (pgmap->ref == &pgmap->internal_ref)
-		pgmap->ref = NULL;
-}
-
 static void pageunmap_range(struct dev_pagemap *pgmap, int range_id)
 {
 	struct range *range = &pgmap->ranges[range_id];
@@ -167,14 +143,15 @@
 	unsigned long pfn;
 	int i;
 
-	dev_pagemap_kill(pgmap);
+	percpu_ref_kill(&pgmap->ref);
 	for (i = 0; i < pgmap->nr_range; i++)
 		for_each_device_pfn(pfn, pgmap, i)
 			put_page(pfn_to_page(pfn));
-	dev_pagemap_cleanup(pgmap);
+	wait_for_completion(&pgmap->done);
 
 	for (i = 0; i < pgmap->nr_range; i++)
 		pageunmap_range(pgmap, i);
+	percpu_ref_exit(&pgmap->ref);
 
 	WARN_ONCE(pgmap->altmap.alloc, "failed to free all reserved pages\n");
 	devmap_managed_enable_put(pgmap);
@@ -188,8 +165,7 @@
 
 static void dev_pagemap_percpu_release(struct percpu_ref *ref)
 {
-	struct dev_pagemap *pgmap =
-		container_of(ref, struct dev_pagemap, internal_ref);
+	struct dev_pagemap *pgmap = container_of(ref, struct dev_pagemap, ref);
 
 	complete(&pgmap->done);
 }
@@ -245,7 +221,7 @@
 
 	if (!mhp_range_allowed(range->start, range_len(range), !is_private)) {
 		error = -EINVAL;
-		goto err_pfn_remap;
+		goto err_kasan;
 	}
 
 	mem_hotplug_begin();
@@ -295,8 +271,8 @@
 	memmap_init_zone_device(&NODE_DATA(nid)->node_zones[ZONE_DEVICE],
 				PHYS_PFN(range->start),
 				PHYS_PFN(range_len(range)), pgmap);
-	percpu_ref_get_many(pgmap->ref, pfn_end(pgmap, range_id)
-			- pfn_first(pgmap, range_id));
+	percpu_ref_get_many(&pgmap->ref,
+		pfn_end(pgmap, range_id) - pfn_first(pgmap, range_id));
 	return 0;
 
 err_add_memory:
@@ -351,6 +327,7 @@
 			WARN(1, "File system DAX not supported\n");
 			return ERR_PTR(-EINVAL);
 		}
+		params.pgprot = pgprot_decrypted(params.pgprot);
 		break;
 	case MEMORY_DEVICE_GENERIC:
 		break;
@@ -362,22 +339,11 @@
 		break;
 	}
 
-	if (!pgmap->ref) {
-		if (pgmap->ops && (pgmap->ops->kill || pgmap->ops->cleanup))
-			return ERR_PTR(-EINVAL);
-
-		init_completion(&pgmap->done);
-		error = percpu_ref_init(&pgmap->internal_ref,
-				dev_pagemap_percpu_release, 0, GFP_KERNEL);
-		if (error)
-			return ERR_PTR(error);
-		pgmap->ref = &pgmap->internal_ref;
-	} else {
-		if (!pgmap->ops || !pgmap->ops->kill || !pgmap->ops->cleanup) {
-			WARN(1, "Missing reference count teardown definition\n");
-			return ERR_PTR(-EINVAL);
-		}
-	}
+	init_completion(&pgmap->done);
+	error = percpu_ref_init(&pgmap->ref, dev_pagemap_percpu_release, 0,
+				GFP_KERNEL);
+	if (error)
+		return ERR_PTR(error);
 
 	devmap_managed_enable_get(pgmap);
 
@@ -486,7 +452,7 @@
 	/* fall back to slow path lookup */
 	rcu_read_lock();
 	pgmap = xa_load(&pgmap_array, PHYS_PFN(phys));
-	if (pgmap && !percpu_ref_tryget_live(pgmap->ref))
+	if (pgmap && !percpu_ref_tryget_live(&pgmap->ref))
 		pgmap = NULL;
 	rcu_read_unlock();
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/memtest.c
+++ linux-xilinx-zynqmp-5.15.0/mm/memtest.c
@@ -46,10 +46,10 @@
 	last_bad = 0;
 
 	for (p = start; p < end; p++)
-		*p = pattern;
+		WRITE_ONCE(*p, pattern);
 
 	for (p = start; p < end; p++, start_phys_aligned += incr) {
-		if (*p == pattern)
+		if (READ_ONCE(*p) == pattern)
 			continue;
 		if (start_phys_aligned == last_bad + incr) {
 			last_bad += incr;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/migrate.c
+++ linux-xilinx-zynqmp-5.15.0/mm/migrate.c
@@ -134,7 +134,7 @@
  *
  * This function shall be used whenever the isolated pageset has been
  * built from lru, balloon, hugetlbfs page. See isolate_migratepages_range()
- * and isolate_huge_page().
+ * and isolate_hugetlb().
  */
 void putback_movable_pages(struct list_head *l)
 {
@@ -424,8 +424,12 @@
 	if (PageSwapBacked(page)) {
 		__SetPageSwapBacked(newpage);
 		if (PageSwapCache(page)) {
+			int i;
+
 			SetPageSwapCache(newpage);
-			set_page_private(newpage, page_private(page));
+			for (i = 0; i < (1 << compound_order(page)); i++)
+				set_page_private(newpage + i,
+						 page_private(page + i));
 		}
 	} else {
 		VM_BUG_ON_PAGE(PageSwapCache(page), page);
@@ -948,9 +952,12 @@
 		if (!PageMappingFlags(page))
 			page->mapping = NULL;
 
-		if (likely(!is_zone_device_page(newpage)))
-			flush_dcache_page(newpage);
+		if (likely(!is_zone_device_page(newpage))) {
+			int i, nr = compound_nr(newpage);
 
+			for (i = 0; i < nr; i++)
+				flush_dcache_page(newpage + i);
+		}
 	}
 out:
 	return rc;
@@ -1719,8 +1726,9 @@
 
 	if (PageHuge(page)) {
 		if (PageHead(page)) {
-			isolate_huge_page(page, pagelist);
-			err = 1;
+			err = isolate_hugetlb(page, pagelist);
+			if (!err)
+				err = 1;
 		}
 	} else {
 		struct page *head;
@@ -1784,6 +1792,7 @@
 			 const int __user *nodes,
 			 int __user *status, int flags)
 {
+	compat_uptr_t __user *compat_pages = (void __user *)pages;
 	int current_node = NUMA_NO_NODE;
 	LIST_HEAD(pagelist);
 	int start, i;
@@ -1797,8 +1806,17 @@
 		int node;
 
 		err = -EFAULT;
-		if (get_user(p, pages + i))
-			goto out_flush;
+		if (in_compat_syscall()) {
+			compat_uptr_t cp;
+
+			if (get_user(cp, compat_pages + i))
+				goto out_flush;
+
+			p = compat_ptr(cp);
+		} else {
+			if (get_user(p, pages + i))
+				goto out_flush;
+		}
 		if (get_user(node, nodes + i))
 			goto out_flush;
 		addr = (unsigned long)untagged_addr(p);
@@ -2419,13 +2437,14 @@
 		migrate->dst[migrate->npages] = 0;
 		migrate->src[migrate->npages++] = mpfn;
 	}
-	arch_leave_lazy_mmu_mode();
-	pte_unmap_unlock(ptep - 1, ptl);
 
 	/* Only flush the TLB if we actually modified any entries */
 	if (unmapped)
 		flush_tlb_range(walk->vma, start, end);
 
+	arch_leave_lazy_mmu_mode();
+	pte_unmap_unlock(ptep - 1, ptl);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mlock.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mlock.c
@@ -826,18 +826,18 @@
 
 	locked = (size + PAGE_SIZE - 1) >> PAGE_SHIFT;
 	lock_limit = rlimit(RLIMIT_MEMLOCK);
-	if (lock_limit == RLIM_INFINITY)
-		allowed = 1;
-	lock_limit >>= PAGE_SHIFT;
+	if (lock_limit != RLIM_INFINITY)
+		lock_limit >>= PAGE_SHIFT;
 	spin_lock(&shmlock_user_lock);
 	memlock = inc_rlimit_ucounts(ucounts, UCOUNT_RLIMIT_MEMLOCK, locked);
 
-	if (!allowed && (memlock == LONG_MAX || memlock > lock_limit) && !capable(CAP_IPC_LOCK)) {
+	if ((memlock == LONG_MAX || memlock > lock_limit) && !capable(CAP_IPC_LOCK)) {
 		dec_rlimit_ucounts(ucounts, UCOUNT_RLIMIT_MEMLOCK, locked);
 		goto out;
 	}
 	if (!get_ucounts(ucounts)) {
 		dec_rlimit_ucounts(ucounts, UCOUNT_RLIMIT_MEMLOCK, locked);
+		allowed = 0;
 		goto out;
 	}
 	allowed = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mmap.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mmap.c
@@ -180,10 +180,9 @@
 	struct vm_area_struct *next = vma->vm_next;
 
 	might_sleep();
-	if (vma->vm_ops && vma->vm_ops->close)
-		vma->vm_ops->close(vma);
+	vma_close(vma);
 	if (vma->vm_file)
-		fput(vma->vm_file);
+		vma_fput(vma);
 	mpol_put(vma_policy(vma));
 	vm_area_free(vma);
 	return next;
@@ -952,7 +951,7 @@
 	if (remove_next) {
 		if (file) {
 			uprobe_munmap(next, next->vm_start, next->vm_end);
-			fput(file);
+			vma_fput(vma);
 		}
 		if (next->anon_vma)
 			anon_vma_merge(vma, next);
@@ -1467,7 +1466,7 @@
 	 * to. we assume access permissions have been handled by the open
 	 * of the memory object, so we don't do any here.
 	 */
-	vm_flags = calc_vm_prot_bits(prot, pkey) | calc_vm_flag_bits(flags) |
+	vm_flags = calc_vm_prot_bits(prot, pkey) | calc_vm_flag_bits(file, flags) |
 			mm->def_flags | VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC;
 
 	if (flags & MAP_LOCKED)
@@ -1684,8 +1683,12 @@
 	    pgprot_val(vm_pgprot_modify(vm_page_prot, vm_flags)))
 		return 0;
 
-	/* Do we need to track softdirty? */
-	if (IS_ENABLED(CONFIG_MEM_SOFT_DIRTY) && !(vm_flags & VM_SOFTDIRTY))
+	/*
+	 * Do we need to track softdirty? hugetlb does not support softdirty
+	 * tracking yet.
+	 */
+	if (IS_ENABLED(CONFIG_MEM_SOFT_DIRTY) && !(vm_flags & VM_SOFTDIRTY) &&
+	    !is_vm_hugetlb_page(vma))
 		return 1;
 
 	/* Specialty mapping? */
@@ -1713,7 +1716,7 @@
 	return (vm_flags & (VM_NORESERVE | VM_SHARED | VM_WRITE)) == VM_WRITE;
 }
 
-unsigned long mmap_region(struct file *file, unsigned long addr,
+static unsigned long __mmap_region(struct file *file, unsigned long addr,
 		unsigned long len, vm_flags_t vm_flags, unsigned long pgoff,
 		struct list_head *uf)
 {
@@ -1777,16 +1780,10 @@
 	vma->vm_pgoff = pgoff;
 
 	if (file) {
-		if (vm_flags & VM_SHARED) {
-			error = mapping_map_writable(file->f_mapping);
-			if (error)
-				goto free_vma;
-		}
-
 		vma->vm_file = get_file(file);
-		error = call_mmap(file, vma);
+		error = mmap_file(file, vma);
 		if (error)
-			goto unmap_and_free_vma;
+			goto unmap_and_free_file_vma;
 
 		/* Can addr have changed??
 		 *
@@ -1797,9 +1794,25 @@
 		 */
 		WARN_ON_ONCE(addr != vma->vm_start);
 
+		/*
+		 * Drivers should not permit writability when previously it was
+		 * disallowed.
+		 */
+		VM_WARN_ON_ONCE(vm_flags != vma->vm_flags &&
+				!(vm_flags & VM_MAYWRITE) &&
+				(vma->vm_flags & VM_MAYWRITE));
+
+		/*
+		 * Drivers should not permit writability when previously it was
+		 * disallowed.
+		 */
+		VM_WARN_ON_ONCE(vm_flags != vma->vm_flags &&
+				!(vm_flags & VM_MAYWRITE) &&
+				(vma->vm_flags & VM_MAYWRITE));
+
 		addr = vma->vm_start;
 
-		/* If vm_flags changed after call_mmap(), we should try merge vma again
+		/* If vm_flags changed after mmap_file(), we should try merge vma again
 		 * as we may succeed this time.
 		 */
 		if (unlikely(vm_flags != vma->vm_flags && prev)) {
@@ -1815,7 +1828,7 @@
 				vma = merge;
 				/* Update vm_flags to pick up the change. */
 				vm_flags = vma->vm_flags;
-				goto unmap_writable;
+				goto file_expanded;
 			}
 		}
 
@@ -1828,20 +1841,13 @@
 		vma_set_anonymous(vma);
 	}
 
-	/* Allow architectures to sanity-check the vm_flags */
-	if (!arch_validate_flags(vma->vm_flags)) {
-		error = -EINVAL;
-		if (file)
-			goto unmap_and_free_vma;
-		else
-			goto free_vma;
-	}
+#ifdef CONFIG_SPARC64
+	/* TODO: Fix SPARC ADI! */
+	WARN_ON_ONCE(!arch_validate_flags(vm_flags));
+#endif
 
 	vma_link(mm, vma, prev, rb_link, rb_parent);
-	/* Once vma denies write, undo our temporary denial count */
-unmap_writable:
-	if (file && vm_flags & VM_SHARED)
-		mapping_unmap_writable(file->f_mapping);
+file_expanded:
 	file = vma->vm_file;
 out:
 	perf_event_mmap(vma);
@@ -1872,15 +1878,12 @@
 
 	return addr;
 
-unmap_and_free_vma:
-	fput(vma->vm_file);
+unmap_and_free_file_vma:
+	vma_fput(vma);
 	vma->vm_file = NULL;
 
 	/* Undo any partial mapping done by a device driver. */
 	unmap_region(mm, vma, prev, vma->vm_start, vma->vm_end);
-	charged = 0;
-	if (vm_flags & VM_SHARED)
-		mapping_unmap_writable(file->f_mapping);
 free_vma:
 	vm_area_free(vma);
 unacct_error:
@@ -2113,14 +2116,6 @@
 	return addr;
 }
 
-#ifndef arch_get_mmap_end
-#define arch_get_mmap_end(addr)	(TASK_SIZE)
-#endif
-
-#ifndef arch_get_mmap_base
-#define arch_get_mmap_base(addr, base) (base)
-#endif
-
 /* Get an address range which is currently unmapped.
  * For shmat() with addr=0.
  *
@@ -2551,7 +2546,7 @@
 	if (!*endptr)
 		stack_guard_gap = val << PAGE_SHIFT;
 
-	return 0;
+	return 1;
 }
 __setup("stack_guard_gap=", cmdline_parse_stack_guard_gap);
 
@@ -2643,11 +2638,28 @@
 {
 	struct vm_area_struct *next = vma_next(mm, prev);
 	struct mmu_gather tlb;
+	struct vm_area_struct *cur_vma;
 
 	lru_add_drain();
 	tlb_gather_mmu(&tlb, mm);
 	update_hiwater_rss(mm);
 	unmap_vmas(&tlb, vma, start, end);
+
+	/*
+	 * Ensure we have no stale TLB entries by the time this mapping is
+	 * removed from the rmap.
+	 * Note that we don't have to worry about nested flushes here because
+	 * we're holding the mm semaphore for removing the mapping - so any
+	 * concurrent flush in this region has to be coming through the rmap,
+	 * and we synchronize against that using the rmap lock.
+	 */
+	for (cur_vma = vma; cur_vma; cur_vma = cur_vma->vm_next) {
+		if ((cur_vma->vm_flags & (VM_PFNMAP|VM_MIXEDMAP)) != 0) {
+			tlb_flush_mmu(&tlb);
+			break;
+		}
+	}
+
 	free_pgtables(&tlb, vma, prev ? prev->vm_end : FIRST_USER_ADDRESS,
 				 next ? next->vm_start : USER_PGTABLES_CEILING);
 	tlb_finish_mmu(&tlb);
@@ -2731,7 +2743,7 @@
 		goto out_free_mpol;
 
 	if (new->vm_file)
-		get_file(new->vm_file);
+		vma_get_file(new);
 
 	if (new->vm_ops && new->vm_ops->open)
 		new->vm_ops->open(new);
@@ -2747,10 +2759,9 @@
 		return 0;
 
 	/* Clean everything up if vma_adjust failed. */
-	if (new->vm_ops && new->vm_ops->close)
-		new->vm_ops->close(new);
+	vma_close(new);
 	if (new->vm_file)
-		fput(new->vm_file);
+		vma_fput(new);
 	unlink_anon_vmas(new);
  out_free_mpol:
 	mpol_put(vma_policy(new));
@@ -2895,6 +2906,36 @@
 	return __do_munmap(mm, start, len, uf, false);
 }
 
+unsigned long mmap_region(struct file *file, unsigned long addr,
+			  unsigned long len, vm_flags_t vm_flags, unsigned long pgoff,
+			  struct list_head *uf)
+{
+	unsigned long ret;
+	bool writable_file_mapping = false;
+
+	/* Allow architectures to sanity-check the vm_flags. */
+	if (!arch_validate_flags(vm_flags))
+		return -EINVAL;
+
+	/* Map writable and ensure this isn't a sealed memfd. */
+	if (file && (vm_flags & VM_SHARED)) {
+		int error = mapping_map_writable(file->f_mapping);
+
+		if (error)
+			return error;
+		writable_file_mapping = true;
+	}
+
+	ret = __mmap_region(file, addr, len, vm_flags, pgoff, uf);
+
+	/* Clear our write mapping regardless of error. */
+	if (writable_file_mapping)
+		mapping_unmap_writable(file->f_mapping);
+
+	validate_mm(current->mm);
+	return ret;
+}
+
 static int __vm_munmap(unsigned long start, size_t len, bool downgrade)
 {
 	int ret;
@@ -2945,7 +2986,7 @@
 	struct vm_area_struct *vma;
 	unsigned long populate = 0;
 	unsigned long ret = -EINVAL;
-	struct file *file;
+	struct file *file, *prfile;
 
 	pr_warn_once("%s (%d) uses deprecated remap_file_pages() syscall. See Documentation/vm/remap_file_pages.rst.\n",
 		     current->comm, current->pid);
@@ -3001,10 +3042,27 @@
 	if (vma->vm_flags & VM_LOCKED)
 		flags |= MAP_LOCKED;
 
-	file = get_file(vma->vm_file);
+	vma_get_file(vma);
+	file = vma->vm_file;
+	prfile = vma->vm_prfile;
 	ret = do_mmap(vma->vm_file, start, size,
 			prot, flags, pgoff, &populate, NULL);
+	if (!IS_ERR_VALUE(ret) && file && prfile) {
+		struct vm_area_struct *new_vma;
+
+		new_vma = find_vma(mm, ret);
+		if (!new_vma->vm_prfile)
+			new_vma->vm_prfile = prfile;
+		if (new_vma != vma)
+			get_file(prfile);
+	}
+	/*
+	 * two fput()s instead of vma_fput(vma),
+	 * coz vma may not be available anymore.
+	 */
 	fput(file);
+	if (prfile)
+		fput(prfile);
 out:
 	mmap_write_unlock(mm);
 	if (populate)
@@ -3285,7 +3343,7 @@
 		if (anon_vma_clone(new_vma, vma))
 			goto out_free_mempol;
 		if (new_vma->vm_file)
-			get_file(new_vma->vm_file);
+			vma_get_file(new_vma);
 		if (new_vma->vm_ops && new_vma->vm_ops->open)
 			new_vma->vm_ops->open(new_vma);
 		vma_link(mm, new_vma, prev, rb_link, rb_parent);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mmap_lock.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mmap_lock.c
@@ -19,14 +19,7 @@
 
 #ifdef CONFIG_MEMCG
 
-/*
- * Our various events all share the same buffer (because we don't want or need
- * to allocate a set of buffers *per event type*), so we need to protect against
- * concurrent _reg() and _unreg() calls, and count how many _reg() calls have
- * been made.
- */
-static DEFINE_MUTEX(reg_lock);
-static int reg_refcount; /* Protected by reg_lock. */
+static atomic_t reg_refcount;
 
 /*
  * Size of the buffer for memcg path names. Ignoring stack trace support,
@@ -34,136 +27,22 @@
  */
 #define MEMCG_PATH_BUF_SIZE MAX_FILTER_STR_VAL
 
-/*
- * How many contexts our trace events might be called in: normal, softirq, irq,
- * and NMI.
- */
-#define CONTEXT_COUNT 4
-
-struct memcg_path {
-	local_lock_t lock;
-	char __rcu *buf;
-	local_t buf_idx;
-};
-static DEFINE_PER_CPU(struct memcg_path, memcg_paths) = {
-	.lock = INIT_LOCAL_LOCK(lock),
-	.buf_idx = LOCAL_INIT(0),
-};
-
-static char **tmp_bufs;
-
-/* Called with reg_lock held. */
-static void free_memcg_path_bufs(void)
-{
-	struct memcg_path *memcg_path;
-	int cpu;
-	char **old = tmp_bufs;
-
-	for_each_possible_cpu(cpu) {
-		memcg_path = per_cpu_ptr(&memcg_paths, cpu);
-		*(old++) = rcu_dereference_protected(memcg_path->buf,
-			lockdep_is_held(&reg_lock));
-		rcu_assign_pointer(memcg_path->buf, NULL);
-	}
-
-	/* Wait for inflight memcg_path_buf users to finish. */
-	synchronize_rcu();
-
-	old = tmp_bufs;
-	for_each_possible_cpu(cpu) {
-		kfree(*(old++));
-	}
-
-	kfree(tmp_bufs);
-	tmp_bufs = NULL;
-}
-
 int trace_mmap_lock_reg(void)
 {
-	int cpu;
-	char *new;
-
-	mutex_lock(&reg_lock);
-
-	/* If the refcount is going 0->1, proceed with allocating buffers. */
-	if (reg_refcount++)
-		goto out;
-
-	tmp_bufs = kmalloc_array(num_possible_cpus(), sizeof(*tmp_bufs),
-				 GFP_KERNEL);
-	if (tmp_bufs == NULL)
-		goto out_fail;
-
-	for_each_possible_cpu(cpu) {
-		new = kmalloc(MEMCG_PATH_BUF_SIZE * CONTEXT_COUNT, GFP_KERNEL);
-		if (new == NULL)
-			goto out_fail_free;
-		rcu_assign_pointer(per_cpu_ptr(&memcg_paths, cpu)->buf, new);
-		/* Don't need to wait for inflights, they'd have gotten NULL. */
-	}
-
-out:
-	mutex_unlock(&reg_lock);
+	atomic_inc(&reg_refcount);
 	return 0;
-
-out_fail_free:
-	free_memcg_path_bufs();
-out_fail:
-	/* Since we failed, undo the earlier ref increment. */
-	--reg_refcount;
-
-	mutex_unlock(&reg_lock);
-	return -ENOMEM;
 }
 
 void trace_mmap_lock_unreg(void)
 {
-	mutex_lock(&reg_lock);
-
-	/* If the refcount is going 1->0, proceed with freeing buffers. */
-	if (--reg_refcount)
-		goto out;
-
-	free_memcg_path_bufs();
-
-out:
-	mutex_unlock(&reg_lock);
-}
-
-static inline char *get_memcg_path_buf(void)
-{
-	struct memcg_path *memcg_path = this_cpu_ptr(&memcg_paths);
-	char *buf;
-	int idx;
-
-	rcu_read_lock();
-	buf = rcu_dereference(memcg_path->buf);
-	if (buf == NULL) {
-		rcu_read_unlock();
-		return NULL;
-	}
-	idx = local_add_return(MEMCG_PATH_BUF_SIZE, &memcg_path->buf_idx) -
-	      MEMCG_PATH_BUF_SIZE;
-	return &buf[idx];
+	atomic_dec(&reg_refcount);
 }
 
-static inline void put_memcg_path_buf(void)
-{
-	local_sub(MEMCG_PATH_BUF_SIZE, &this_cpu_ptr(&memcg_paths)->buf_idx);
-	rcu_read_unlock();
-}
-
-#define TRACE_MMAP_LOCK_EVENT(type, mm, ...)                                   \
-	do {                                                                   \
-		const char *memcg_path;                                        \
-		local_lock(&memcg_paths.lock);                                 \
-		memcg_path = get_mm_memcg_path(mm);                            \
-		trace_mmap_lock_##type(mm,                                     \
-				       memcg_path != NULL ? memcg_path : "",   \
-				       ##__VA_ARGS__);                         \
-		if (likely(memcg_path != NULL))                                \
-			put_memcg_path_buf();                                  \
-		local_unlock(&memcg_paths.lock);                               \
+#define TRACE_MMAP_LOCK_EVENT(type, mm, ...)                    \
+	do {                                                    \
+		char buf[MEMCG_PATH_BUF_SIZE];                  \
+		get_mm_memcg_path(mm, buf, sizeof(buf));        \
+		trace_mmap_lock_##type(mm, buf, ##__VA_ARGS__); \
 	} while (0)
 
 #else /* !CONFIG_MEMCG */
@@ -185,37 +64,23 @@
 #ifdef CONFIG_TRACING
 #ifdef CONFIG_MEMCG
 /*
- * Write the given mm_struct's memcg path to a percpu buffer, and return a
- * pointer to it. If the path cannot be determined, or no buffer was available
- * (because the trace event is being unregistered), NULL is returned.
- *
- * Note: buffers are allocated per-cpu to avoid locking, so preemption must be
- * disabled by the caller before calling us, and re-enabled only after the
- * caller is done with the pointer.
- *
- * The caller must call put_memcg_path_buf() once the buffer is no longer
- * needed. This must be done while preemption is still disabled.
+ * Write the given mm_struct's memcg path to a buffer. If the path cannot be
+ * determined or the trace event is being unregistered, empty string is written.
  */
-static const char *get_mm_memcg_path(struct mm_struct *mm)
+static void get_mm_memcg_path(struct mm_struct *mm, char *buf, size_t buflen)
 {
-	char *buf = NULL;
-	struct mem_cgroup *memcg = get_mem_cgroup_from_mm(mm);
+	struct mem_cgroup *memcg;
 
+	buf[0] = '\0';
+	/* No need to get path if no trace event is registered. */
+	if (!atomic_read(&reg_refcount))
+		return;
+	memcg = get_mem_cgroup_from_mm(mm);
 	if (memcg == NULL)
-		goto out;
-	if (unlikely(memcg->css.cgroup == NULL))
-		goto out_put;
-
-	buf = get_memcg_path_buf();
-	if (buf == NULL)
-		goto out_put;
-
-	cgroup_path(memcg->css.cgroup, buf, MEMCG_PATH_BUF_SIZE);
-
-out_put:
+		return;
+	if (memcg->css.cgroup)
+		cgroup_path(memcg->css.cgroup, buf, buflen);
 	css_put(&memcg->css);
-out:
-	return buf;
 }
 
 #endif /* CONFIG_MEMCG */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mmu_gather.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mmu_gather.c
@@ -139,7 +139,7 @@
 	/* Simply deliver the interrupt */
 }
 
-static void tlb_remove_table_sync_one(void)
+void tlb_remove_table_sync_one(void)
 {
 	/*
 	 * This isn't an RCU grace period and hence the page-tables cannot be
@@ -163,8 +163,6 @@
 
 #else /* !CONFIG_MMU_GATHER_RCU_TABLE_FREE */
 
-static void tlb_remove_table_sync_one(void) { }
-
 static void tlb_remove_table_free(struct mmu_table_batch *batch)
 {
 	__tlb_remove_table_free(batch);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mmu_notifier.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mmu_notifier.c
@@ -1036,6 +1036,18 @@
 }
 EXPORT_SYMBOL_GPL(mmu_interval_notifier_insert_locked);
 
+static bool
+mmu_interval_seq_released(struct mmu_notifier_subscriptions *subscriptions,
+			  unsigned long seq)
+{
+	bool ret;
+
+	spin_lock(&subscriptions->lock);
+	ret = subscriptions->invalidate_seq != seq;
+	spin_unlock(&subscriptions->lock);
+	return ret;
+}
+
 /**
  * mmu_interval_notifier_remove - Remove a interval notifier
  * @interval_sub: Interval subscription to unregister
@@ -1083,7 +1095,7 @@
 	lock_map_release(&__mmu_notifier_invalidate_range_start_map);
 	if (seq)
 		wait_event(subscriptions->wq,
-			   READ_ONCE(subscriptions->invalidate_seq) != seq);
+			   mmu_interval_seq_released(subscriptions, seq));
 
 	/* pairs with mmgrab in mmu_interval_notifier_insert() */
 	mmdrop(mm);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mprotect.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mprotect.c
@@ -94,7 +94,7 @@
 
 				/* Also skip shared copy-on-write pages */
 				if (is_cow_mapping(vma->vm_flags) &&
-				    page_mapcount(page) != 1)
+				    page_count(page) != 1)
 					continue;
 
 				/*
--- linux-xilinx-zynqmp-5.15.0.orig/mm/mremap.c
+++ linux-xilinx-zynqmp-5.15.0/mm/mremap.c
@@ -486,6 +486,9 @@
 	pmd_t *old_pmd, *new_pmd;
 	pud_t *old_pud, *new_pud;
 
+	if (!len)
+		return 0;
+
 	old_end = old_addr + len;
 	flush_cache_range(vma, old_addr, old_end);
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/nommu.c
+++ linux-xilinx-zynqmp-5.15.0/mm/nommu.c
@@ -523,7 +523,7 @@
 		up_write(&nommu_region_sem);
 
 		if (region->vm_file)
-			fput(region->vm_file);
+			vmr_fput(region);
 
 		/* IO memory and memory shared directly out of the pagecache
 		 * from ramfs/tmpfs mustn't be released here */
@@ -652,10 +652,9 @@
  */
 static void delete_vma(struct mm_struct *mm, struct vm_area_struct *vma)
 {
-	if (vma->vm_ops && vma->vm_ops->close)
-		vma->vm_ops->close(vma);
+	vma_close(vma);
 	if (vma->vm_file)
-		fput(vma->vm_file);
+		vma_fput(vma);
 	put_nommu_region(vma->vm_region);
 	vm_area_free(vma);
 }
@@ -907,7 +906,7 @@
 {
 	unsigned long vm_flags;
 
-	vm_flags = calc_vm_prot_bits(prot, 0) | calc_vm_flag_bits(flags);
+	vm_flags = calc_vm_prot_bits(prot, 0) | calc_vm_flag_bits(file, flags);
 	/* vm_flags |= mm->def_flags; */
 
 	if (!(capabilities & NOMMU_MAP_DIRECT)) {
@@ -942,7 +941,7 @@
 {
 	int ret;
 
-	ret = call_mmap(vma->vm_file, vma);
+	ret = mmap_file(vma->vm_file, vma);
 	if (ret == 0) {
 		vma->vm_region->vm_top = vma->vm_region->vm_end;
 		return 0;
@@ -973,7 +972,7 @@
 	 * - VM_MAYSHARE will be set if it may attempt to share
 	 */
 	if (capabilities & NOMMU_MAP_DIRECT) {
-		ret = call_mmap(vma->vm_file, vma);
+		ret = mmap_file(vma->vm_file, vma);
 		if (ret == 0) {
 			/* shouldn't return success if we're not sharing */
 			BUG_ON(!(vma->vm_flags & VM_MAYSHARE));
@@ -1175,7 +1174,7 @@
 					goto error_just_free;
 				}
 			}
-			fput(region->vm_file);
+			vmr_fput(region);
 			kmem_cache_free(vm_region_jar, region);
 			region = pregion;
 			result = start;
@@ -1252,10 +1251,10 @@
 	up_write(&nommu_region_sem);
 error:
 	if (region->vm_file)
-		fput(region->vm_file);
+		vmr_fput(region);
 	kmem_cache_free(vm_region_jar, region);
 	if (vma->vm_file)
-		fput(vma->vm_file);
+		vma_fput(vma);
 	vm_area_free(vma);
 	return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/oom_kill.c
+++ linux-xilinx-zynqmp-5.15.0/mm/oom_kill.c
@@ -44,6 +44,8 @@
 #include <linux/kthread.h>
 #include <linux/init.h>
 #include <linux/mmu_notifier.h>
+#include <linux/cred.h>
+#include <linux/nmi.h>
 
 #include <asm/tlb.h>
 #include "internal.h"
@@ -432,10 +434,15 @@
 		mem_cgroup_scan_tasks(oc->memcg, dump_task, oc);
 	else {
 		struct task_struct *p;
+		int i = 0;
 
 		rcu_read_lock();
-		for_each_process(p)
+		for_each_process(p) {
+			/* Avoid potential softlockup warning */
+			if ((++i & 1023) == 0)
+				touch_softlockup_watchdog();
 			dump_task(p, oc);
+		}
 		rcu_read_unlock();
 	}
 }
@@ -635,7 +642,7 @@
 	 */
 	set_bit(MMF_OOM_SKIP, &mm->flags);
 
-	/* Drop a reference taken by wake_oom_reaper */
+	/* Drop a reference taken by queue_oom_reaper */
 	put_task_struct(tsk);
 }
 
@@ -645,12 +652,12 @@
 		struct task_struct *tsk = NULL;
 
 		wait_event_freezable(oom_reaper_wait, oom_reaper_list != NULL);
-		spin_lock(&oom_reaper_lock);
+		spin_lock_irq(&oom_reaper_lock);
 		if (oom_reaper_list != NULL) {
 			tsk = oom_reaper_list;
 			oom_reaper_list = tsk->oom_reaper_list;
 		}
-		spin_unlock(&oom_reaper_lock);
+		spin_unlock_irq(&oom_reaper_lock);
 
 		if (tsk)
 			oom_reap_task(tsk);
@@ -659,22 +666,48 @@
 	return 0;
 }
 
-static void wake_oom_reaper(struct task_struct *tsk)
+static void wake_oom_reaper(struct timer_list *timer)
 {
-	/* mm is already queued? */
-	if (test_and_set_bit(MMF_OOM_REAP_QUEUED, &tsk->signal->oom_mm->flags))
-		return;
+	struct task_struct *tsk = container_of(timer, struct task_struct,
+			oom_reaper_timer);
+	struct mm_struct *mm = tsk->signal->oom_mm;
+	unsigned long flags;
 
-	get_task_struct(tsk);
+	/* The victim managed to terminate on its own - see exit_mmap */
+	if (test_bit(MMF_OOM_SKIP, &mm->flags)) {
+		put_task_struct(tsk);
+		return;
+	}
 
-	spin_lock(&oom_reaper_lock);
+	spin_lock_irqsave(&oom_reaper_lock, flags);
 	tsk->oom_reaper_list = oom_reaper_list;
 	oom_reaper_list = tsk;
-	spin_unlock(&oom_reaper_lock);
+	spin_unlock_irqrestore(&oom_reaper_lock, flags);
 	trace_wake_reaper(tsk->pid);
 	wake_up(&oom_reaper_wait);
 }
 
+/*
+ * Give the OOM victim time to exit naturally before invoking the oom_reaping.
+ * The timers timeout is arbitrary... the longer it is, the longer the worst
+ * case scenario for the OOM can take. If it is too small, the oom_reaper can
+ * get in the way and release resources needed by the process exit path.
+ * e.g. The futex robust list can sit in Anon|Private memory that gets reaped
+ * before the exit path is able to wake the futex waiters.
+ */
+#define OOM_REAPER_DELAY (2*HZ)
+static void queue_oom_reaper(struct task_struct *tsk)
+{
+	/* mm is already queued? */
+	if (test_and_set_bit(MMF_OOM_REAP_QUEUED, &tsk->signal->oom_mm->flags))
+		return;
+
+	get_task_struct(tsk);
+	timer_setup(&tsk->oom_reaper_timer, wake_oom_reaper, 0);
+	tsk->oom_reaper_timer.expires = jiffies + OOM_REAPER_DELAY;
+	add_timer(&tsk->oom_reaper_timer);
+}
+
 static int __init oom_init(void)
 {
 	oom_reaper_th = kthread_run(oom_reaper, NULL, "oom_reaper");
@@ -682,7 +715,7 @@
 }
 subsys_initcall(oom_init)
 #else
-static inline void wake_oom_reaper(struct task_struct *tsk)
+static inline void queue_oom_reaper(struct task_struct *tsk)
 {
 }
 #endif /* CONFIG_MMU */
@@ -699,6 +732,7 @@
  */
 static void mark_oom_victim(struct task_struct *tsk)
 {
+	const struct cred *cred;
 	struct mm_struct *mm = tsk->mm;
 
 	WARN_ON(oom_killer_disabled);
@@ -720,7 +754,9 @@
 	 */
 	__thaw_task(tsk);
 	atomic_inc(&oom_victims);
-	trace_mark_victim(tsk->pid);
+	cred = get_task_cred(tsk);
+	trace_mark_victim(tsk, cred->uid.val);
+	put_cred(cred);
 }
 
 /**
@@ -933,7 +969,7 @@
 	rcu_read_unlock();
 
 	if (can_oom_reap)
-		wake_oom_reaper(victim);
+		queue_oom_reaper(victim);
 
 	mmdrop(mm);
 	put_task_struct(victim);
@@ -969,7 +1005,7 @@
 	task_lock(victim);
 	if (task_will_free_mem(victim)) {
 		mark_oom_victim(victim);
-		wake_oom_reaper(victim);
+		queue_oom_reaper(victim);
 		task_unlock(victim);
 		put_task_struct(victim);
 		return;
@@ -1067,7 +1103,7 @@
 	 */
 	if (task_will_free_mem(current)) {
 		mark_oom_victim(current);
-		wake_oom_reaper(current);
+		queue_oom_reaper(current);
 		return true;
 	}
 
@@ -1120,27 +1156,24 @@
 }
 
 /*
- * The pagefault handler calls here because it is out of memory, so kill a
- * memory-hogging task. If oom_lock is held by somebody else, a parallel oom
- * killing is already in progress so do nothing.
+ * The pagefault handler calls here because some allocation has failed. We have
+ * to take care of the memcg OOM here because this is the only safe context without
+ * any locks held but let the oom killer triggered from the allocation context care
+ * about the global OOM.
  */
 void pagefault_out_of_memory(void)
 {
-	struct oom_control oc = {
-		.zonelist = NULL,
-		.nodemask = NULL,
-		.memcg = NULL,
-		.gfp_mask = 0,
-		.order = 0,
-	};
+	static DEFINE_RATELIMIT_STATE(pfoom_rs, DEFAULT_RATELIMIT_INTERVAL,
+				      DEFAULT_RATELIMIT_BURST);
 
 	if (mem_cgroup_oom_synchronize(true))
 		return;
 
-	if (!mutex_trylock(&oom_lock))
+	if (fatal_signal_pending(current))
 		return;
-	out_of_memory(&oc);
-	mutex_unlock(&oom_lock);
+
+	if (__ratelimit(&pfoom_rs))
+		pr_warn("Huh VM_FAULT_OOM leaked out to the #PF handler. Retrying PF\n");
 }
 
 SYSCALL_DEFINE2(process_mrelease, int, pidfd, unsigned int, flags)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/page-writeback.c
+++ linux-xilinx-zynqmp-5.15.0/mm/page-writeback.c
@@ -426,13 +426,20 @@
 	else
 		bg_thresh = (bg_ratio * available_memory) / PAGE_SIZE;
 
-	if (bg_thresh >= thresh)
-		bg_thresh = thresh / 2;
 	tsk = current;
 	if (rt_task(tsk)) {
 		bg_thresh += bg_thresh / 4 + global_wb_domain.dirty_limit / 32;
 		thresh += thresh / 4 + global_wb_domain.dirty_limit / 32;
 	}
+	/*
+	 * Dirty throttling logic assumes the limits in page units fit into
+	 * 32-bits. This gives 16TB dirty limits max which is hopefully enough.
+	 */
+	if (thresh > UINT_MAX)
+		thresh = UINT_MAX;
+	/* This makes sure bg_thresh is within 32-bits as well */
+	if (bg_thresh >= thresh)
+		bg_thresh = thresh / 2;
 	dtc->thresh = thresh;
 	dtc->bg_thresh = bg_thresh;
 
@@ -482,7 +489,11 @@
 	if (rt_task(tsk))
 		dirty += dirty / 4;
 
-	return dirty;
+	/*
+	 * Dirty throttling logic assumes the limits in page units fit into
+	 * 32-bits. This gives 16TB dirty limits max which is hopefully enough.
+	 */
+	return min_t(unsigned long, dirty, UINT_MAX);
 }
 
 /**
@@ -518,10 +529,17 @@
 		void *buffer, size_t *lenp, loff_t *ppos)
 {
 	int ret;
+	unsigned long old_bytes = dirty_background_bytes;
 
 	ret = proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
-	if (ret == 0 && write)
+	if (ret == 0 && write) {
+		if (DIV_ROUND_UP(dirty_background_bytes, PAGE_SIZE) >
+								UINT_MAX) {
+			dirty_background_bytes = old_bytes;
+			return -ERANGE;
+		}
 		dirty_background_ratio = 0;
+	}
 	return ret;
 }
 
@@ -547,6 +565,10 @@
 
 	ret = proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
 	if (ret == 0 && write && vm_dirty_bytes != old_bytes) {
+		if (DIV_ROUND_UP(vm_dirty_bytes, PAGE_SIZE) > UINT_MAX) {
+			vm_dirty_bytes = old_bytes;
+			return -ERANGE;
+		}
 		writeback_set_ratelimit();
 		vm_dirty_ratio = 0;
 	}
@@ -2755,6 +2777,7 @@
 
 static void wb_inode_writeback_end(struct bdi_writeback *wb)
 {
+	unsigned long flags;
 	atomic_dec(&wb->writeback_inodes);
 	/*
 	 * Make sure estimate of writeback throughput gets updated after
@@ -2763,7 +2786,10 @@
 	 * that if multiple inodes end writeback at a similar time, they get
 	 * batched into one bandwidth update.
 	 */
-	queue_delayed_work(bdi_wq, &wb->bw_dwork, BANDWIDTH_INTERVAL);
+	spin_lock_irqsave(&wb->work_lock, flags);
+	if (test_bit(WB_registered, &wb->state))
+		queue_delayed_work(bdi_wq, &wb->bw_dwork, BANDWIDTH_INTERVAL);
+	spin_unlock_irqrestore(&wb->work_lock, flags);
 }
 
 int test_clear_page_writeback(struct page *page)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/page_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/mm/page_alloc.c
@@ -2461,6 +2461,9 @@
 		del_page_from_free_list(page, zone, current_order);
 		expand(zone, page, order, current_order, migratetype);
 		set_pcppage_migratetype(page, migratetype);
+		trace_mm_page_alloc_zone_locked(page, order, migratetype,
+				pcp_allowed_order(order) &&
+				migratetype < MIGRATE_PCPTYPES);
 		return page;
 	}
 
@@ -2988,7 +2991,7 @@
 		    zone_page_state(zone, NR_FREE_PAGES) / 2) {
 			page = __rmqueue_cma_fallback(zone, order);
 			if (page)
-				goto out;
+				return page;
 		}
 	}
 retry:
@@ -3001,9 +3004,6 @@
 								alloc_flags))
 			goto retry;
 	}
-out:
-	if (page)
-		trace_mm_page_alloc_zone_locked(page, order, migratetype);
 	return page;
 }
 
@@ -3597,6 +3597,53 @@
 #endif
 }
 
+static __always_inline
+struct page *rmqueue_buddy(struct zone *preferred_zone, struct zone *zone,
+			   unsigned int order, unsigned int alloc_flags,
+			   int migratetype)
+{
+	struct page *page;
+	unsigned long flags;
+
+	do {
+		page = NULL;
+		spin_lock_irqsave(&zone->lock, flags);
+		/*
+		 * order-0 request can reach here when the pcplist is skipped
+		 * due to non-CMA allocation context. HIGHATOMIC area is
+		 * reserved for high-order atomic allocation, so order-0
+		 * request should skip it.
+		 */
+		if (alloc_flags & ALLOC_HIGHATOMIC)
+			page = __rmqueue_smallest(zone, order, MIGRATE_HIGHATOMIC);
+		if (!page) {
+			page = __rmqueue(zone, order, migratetype, alloc_flags);
+
+			/*
+			 * If the allocation fails, allow OOM handling and
+			 * order-0 (atomic) allocs access to HIGHATOMIC
+			 * reserves as failing now is worse than failing a
+			 * high-order atomic allocation in the future.
+			 */
+			if (!page && (alloc_flags & (ALLOC_OOM|ALLOC_NON_BLOCK)))
+				page = __rmqueue_smallest(zone, order, MIGRATE_HIGHATOMIC);
+
+			if (!page) {
+				spin_unlock_irqrestore(&zone->lock, flags);
+				return NULL;
+			}
+		}
+		__mod_zone_freepage_state(zone, -(1 << order),
+					  get_pcppage_migratetype(page));
+		spin_unlock_irqrestore(&zone->lock, flags);
+	} while (check_new_pages(page, order));
+
+	__count_zid_vm_events(PGALLOC, page_zonenum(page), 1 << order);
+	zone_statistics(preferred_zone, zone, 1);
+
+	return page;
+}
+
 /* Remove page from the per-cpu list, caller must protect the list */
 static inline
 struct page *__rmqueue_pcplist(struct zone *zone, unsigned int order,
@@ -3677,9 +3724,14 @@
 			gfp_t gfp_flags, unsigned int alloc_flags,
 			int migratetype)
 {
-	unsigned long flags;
 	struct page *page;
 
+	/*
+	 * We most definitely don't want callers attempting to
+	 * allocate greater than order-1 page units with __GFP_NOFAIL.
+	 */
+	WARN_ON_ONCE((gfp_flags & __GFP_NOFAIL) && (order > 1));
+
 	if (likely(pcp_allowed_order(order))) {
 		/*
 		 * MIGRATE_MOVABLE pcplist could have the pages on CMA area and
@@ -3693,38 +3745,10 @@
 		}
 	}
 
-	/*
-	 * We most definitely don't want callers attempting to
-	 * allocate greater than order-1 page units with __GFP_NOFAIL.
-	 */
-	WARN_ON_ONCE((gfp_flags & __GFP_NOFAIL) && (order > 1));
-	spin_lock_irqsave(&zone->lock, flags);
-
-	do {
-		page = NULL;
-		/*
-		 * order-0 request can reach here when the pcplist is skipped
-		 * due to non-CMA allocation context. HIGHATOMIC area is
-		 * reserved for high-order atomic allocation, so order-0
-		 * request should skip it.
-		 */
-		if (order > 0 && alloc_flags & ALLOC_HARDER) {
-			page = __rmqueue_smallest(zone, order, MIGRATE_HIGHATOMIC);
-			if (page)
-				trace_mm_page_alloc_zone_locked(page, order, migratetype);
-		}
-		if (!page)
-			page = __rmqueue(zone, order, migratetype, alloc_flags);
-	} while (page && check_new_pages(page, order));
-	if (!page)
-		goto failed;
-
-	__mod_zone_freepage_state(zone, -(1 << order),
-				  get_pcppage_migratetype(page));
-	spin_unlock_irqrestore(&zone->lock, flags);
-
-	__count_zid_vm_events(PGALLOC, page_zonenum(page), 1 << order);
-	zone_statistics(preferred_zone, zone, 1);
+	page = rmqueue_buddy(preferred_zone, zone, order, alloc_flags,
+							migratetype);
+	if (unlikely(!page))
+		return NULL;
 
 out:
 	/* Separate test+clear to avoid unnecessary atomics */
@@ -3735,10 +3759,6 @@
 
 	VM_BUG_ON_PAGE(page && bad_range(zone, page), page);
 	return page;
-
-failed:
-	spin_unlock_irqrestore(&zone->lock, flags);
-	return NULL;
 }
 
 #ifdef CONFIG_FAIL_PAGE_ALLOC
@@ -3818,15 +3838,14 @@
 static inline long __zone_watermark_unusable_free(struct zone *z,
 				unsigned int order, unsigned int alloc_flags)
 {
-	const bool alloc_harder = (alloc_flags & (ALLOC_HARDER|ALLOC_OOM));
 	long unusable_free = (1 << order) - 1;
 
 	/*
-	 * If the caller does not have rights to ALLOC_HARDER then subtract
-	 * the high-atomic reserves. This will over-estimate the size of the
-	 * atomic reserve but it avoids a search.
+	 * If the caller does not have rights to reserves below the min
+	 * watermark then subtract the high-atomic reserves. This will
+	 * over-estimate the size of the atomic reserve but it avoids a search.
 	 */
-	if (likely(!alloc_harder))
+	if (likely(!(alloc_flags & ALLOC_RESERVES)))
 		unusable_free += z->nr_reserved_highatomic;
 
 #ifdef CONFIG_CMA
@@ -3850,25 +3869,37 @@
 {
 	long min = mark;
 	int o;
-	const bool alloc_harder = (alloc_flags & (ALLOC_HARDER|ALLOC_OOM));
 
 	/* free_pages may go negative - that's OK */
 	free_pages -= __zone_watermark_unusable_free(z, order, alloc_flags);
 
-	if (alloc_flags & ALLOC_HIGH)
-		min -= min / 2;
+	if (unlikely(alloc_flags & ALLOC_RESERVES)) {
+		/*
+		 * __GFP_HIGH allows access to 50% of the min reserve as well
+		 * as OOM.
+		 */
+		if (alloc_flags & ALLOC_MIN_RESERVE) {
+			min -= min / 2;
+
+			/*
+			 * Non-blocking allocations (e.g. GFP_ATOMIC) can
+			 * access more reserves than just __GFP_HIGH. Other
+			 * non-blocking allocations requests such as GFP_NOWAIT
+			 * or (GFP_KERNEL & ~__GFP_DIRECT_RECLAIM) do not get
+			 * access to the min reserve.
+			 */
+			if (alloc_flags & ALLOC_NON_BLOCK)
+				min -= min / 4;
+		}
 
-	if (unlikely(alloc_harder)) {
 		/*
-		 * OOM victims can try even harder than normal ALLOC_HARDER
+		 * OOM victims can try even harder than the normal reserve
 		 * users on the grounds that it's definitely going to be in
 		 * the exit path shortly and free memory. Any allocation it
 		 * makes during the free path will be small and short-lived.
 		 */
 		if (alloc_flags & ALLOC_OOM)
 			min -= min / 2;
-		else
-			min -= min / 4;
 	}
 
 	/*
@@ -3902,8 +3933,10 @@
 			return true;
 		}
 #endif
-		if (alloc_harder && !free_area_empty(area, MIGRATE_HIGHATOMIC))
+		if ((alloc_flags & (ALLOC_HIGHATOMIC|ALLOC_OOM)) &&
+		    !free_area_empty(area, MIGRATE_HIGHATOMIC)) {
 			return true;
+		}
 	}
 	return false;
 }
@@ -3928,11 +3961,15 @@
 	 * need to be calculated.
 	 */
 	if (!order) {
-		long fast_free;
+		long usable_free;
+		long reserved;
 
-		fast_free = free_pages;
-		fast_free -= __zone_watermark_unusable_free(z, 0, alloc_flags);
-		if (fast_free > mark + z->lowmem_reserve[highest_zoneidx])
+		usable_free = free_pages;
+		reserved = __zone_watermark_unusable_free(z, 0, alloc_flags);
+
+		/* reserved may over estimate high-atomic reserves. */
+		usable_free -= min(usable_free, reserved);
+		if (usable_free > mark + z->lowmem_reserve[highest_zoneidx])
 			return true;
 	}
 
@@ -4158,7 +4195,7 @@
 			 * If this is a high-order atomic allocation then check
 			 * if the pageblock should be reserved for the future
 			 */
-			if (unlikely(order && (alloc_flags & ALLOC_HARDER)))
+			if (unlikely(alloc_flags & ALLOC_HIGHATOMIC))
 				reserve_highatomic_pageblock(page, zone, order);
 
 			return page;
@@ -4210,7 +4247,9 @@
 	va_list args;
 	static DEFINE_RATELIMIT_STATE(nopage_rs, 10*HZ, 1);
 
-	if ((gfp_mask & __GFP_NOWARN) || !__ratelimit(&nopage_rs))
+	if ((gfp_mask & __GFP_NOWARN) ||
+	     !__ratelimit(&nopage_rs) ||
+	     ((gfp_mask & __GFP_DMA) && !has_managed_dma()))
 		return;
 
 	va_start(args, fmt);
@@ -4575,6 +4614,30 @@
 EXPORT_SYMBOL_GPL(fs_reclaim_release);
 #endif
 
+/*
+ * Zonelists may change due to hotplug during allocation. Detect when zonelists
+ * have been rebuilt so allocation retries. Reader side does not lock and
+ * retries the allocation if zonelist changes. Writer side is protected by the
+ * embedded spin_lock.
+ */
+static DEFINE_SEQLOCK(zonelist_update_seq);
+
+static unsigned int zonelist_iter_begin(void)
+{
+	if (IS_ENABLED(CONFIG_MEMORY_HOTREMOVE))
+		return read_seqbegin(&zonelist_update_seq);
+
+	return 0;
+}
+
+static unsigned int check_retry_zonelist(unsigned int seq)
+{
+	if (IS_ENABLED(CONFIG_MEMORY_HOTREMOVE))
+		return read_seqretry(&zonelist_update_seq, seq);
+
+	return seq;
+}
+
 /* Perform direct synchronous page reclaim */
 static unsigned long
 __perform_reclaim(gfp_t gfp_mask, unsigned int order,
@@ -4651,41 +4714,48 @@
 }
 
 static inline unsigned int
-gfp_to_alloc_flags(gfp_t gfp_mask)
+gfp_to_alloc_flags(gfp_t gfp_mask, unsigned int order)
 {
 	unsigned int alloc_flags = ALLOC_WMARK_MIN | ALLOC_CPUSET;
 
 	/*
-	 * __GFP_HIGH is assumed to be the same as ALLOC_HIGH
+	 * __GFP_HIGH is assumed to be the same as ALLOC_MIN_RESERVE
 	 * and __GFP_KSWAPD_RECLAIM is assumed to be the same as ALLOC_KSWAPD
 	 * to save two branches.
 	 */
-	BUILD_BUG_ON(__GFP_HIGH != (__force gfp_t) ALLOC_HIGH);
+	BUILD_BUG_ON(__GFP_HIGH != (__force gfp_t) ALLOC_MIN_RESERVE);
 	BUILD_BUG_ON(__GFP_KSWAPD_RECLAIM != (__force gfp_t) ALLOC_KSWAPD);
 
 	/*
 	 * The caller may dip into page reserves a bit more if the caller
 	 * cannot run direct reclaim, or if the caller has realtime scheduling
 	 * policy or is asking for __GFP_HIGH memory.  GFP_ATOMIC requests will
-	 * set both ALLOC_HARDER (__GFP_ATOMIC) and ALLOC_HIGH (__GFP_HIGH).
+	 * set both ALLOC_NON_BLOCK and ALLOC_MIN_RESERVE(__GFP_HIGH).
 	 */
 	alloc_flags |= (__force int)
 		(gfp_mask & (__GFP_HIGH | __GFP_KSWAPD_RECLAIM));
 
-	if (gfp_mask & __GFP_ATOMIC) {
+	if (!(gfp_mask & __GFP_DIRECT_RECLAIM)) {
 		/*
 		 * Not worth trying to allocate harder for __GFP_NOMEMALLOC even
 		 * if it can't schedule.
 		 */
-		if (!(gfp_mask & __GFP_NOMEMALLOC))
-			alloc_flags |= ALLOC_HARDER;
+		if (!(gfp_mask & __GFP_NOMEMALLOC)) {
+			alloc_flags |= ALLOC_NON_BLOCK;
+
+			if (order > 0)
+				alloc_flags |= ALLOC_HIGHATOMIC;
+		}
+
 		/*
-		 * Ignore cpuset mems for GFP_ATOMIC rather than fail, see the
-		 * comment for __cpuset_node_allowed().
+		 * Ignore cpuset mems for non-blocking __GFP_HIGH (probably
+		 * GFP_ATOMIC) rather than fail, see the comment for
+		 * __cpuset_node_allowed().
 		 */
-		alloc_flags &= ~ALLOC_CPUSET;
+		if (alloc_flags & ALLOC_MIN_RESERVE)
+			alloc_flags &= ~ALLOC_CPUSET;
 	} else if (unlikely(rt_task(current)) && in_task())
-		alloc_flags |= ALLOC_HARDER;
+		alloc_flags |= ALLOC_MIN_RESERVE;
 
 	alloc_flags = gfp_to_alloc_flags_cma(gfp_mask, alloc_flags);
 
@@ -4873,6 +4943,7 @@
 						struct alloc_context *ac)
 {
 	bool can_direct_reclaim = gfp_mask & __GFP_DIRECT_RECLAIM;
+	bool can_compact = gfp_compaction_allowed(gfp_mask);
 	const bool costly_order = order > PAGE_ALLOC_COSTLY_ORDER;
 	struct page *page = NULL;
 	unsigned int alloc_flags;
@@ -4882,6 +4953,7 @@
 	int compaction_retries;
 	int no_progress_loops;
 	unsigned int cpuset_mems_cookie;
+	unsigned int zonelist_iter_cookie;
 	int reserve_flags;
 
 	/*
@@ -4892,18 +4964,20 @@
 				(__GFP_ATOMIC|__GFP_DIRECT_RECLAIM)))
 		gfp_mask &= ~__GFP_ATOMIC;
 
-retry_cpuset:
+restart:
 	compaction_retries = 0;
 	no_progress_loops = 0;
+	compact_result = COMPACT_SKIPPED;
 	compact_priority = DEF_COMPACT_PRIORITY;
 	cpuset_mems_cookie = read_mems_allowed_begin();
+	zonelist_iter_cookie = zonelist_iter_begin();
 
 	/*
 	 * The fast path uses conservative alloc_flags to succeed only until
 	 * kswapd needs to be woken up, and to avoid the cost of setting up
 	 * alloc_flags precisely. So we do that now.
 	 */
-	alloc_flags = gfp_to_alloc_flags(gfp_mask);
+	alloc_flags = gfp_to_alloc_flags(gfp_mask, order);
 
 	/*
 	 * We need to recalculate the starting point for the zonelist iterator
@@ -4936,7 +5010,7 @@
 	 * Don't try this for allocations that are allowed to ignore
 	 * watermarks, as the ALLOC_NO_WATERMARKS attempt didn't yet happen.
 	 */
-	if (can_direct_reclaim &&
+	if (can_direct_reclaim && can_compact &&
 			(costly_order ||
 			   (order > 0 && ac->migratetype != MIGRATE_MOVABLE))
 			&& !gfp_pfmemalloc_allowed(gfp_mask)) {
@@ -5033,9 +5107,10 @@
 
 	/*
 	 * Do not retry costly high order allocations unless they are
-	 * __GFP_RETRY_MAYFAIL
+	 * __GFP_RETRY_MAYFAIL and we can compact
 	 */
-	if (costly_order && !(gfp_mask & __GFP_RETRY_MAYFAIL))
+	if (costly_order && (!can_compact ||
+			     !(gfp_mask & __GFP_RETRY_MAYFAIL)))
 		goto nopage;
 
 	if (should_reclaim_retry(gfp_mask, order, ac, alloc_flags,
@@ -5048,16 +5123,20 @@
 	 * implementation of the compaction depends on the sufficient amount
 	 * of free memory (see __compaction_suitable)
 	 */
-	if (did_some_progress > 0 &&
+	if (did_some_progress > 0 && can_compact &&
 			should_compact_retry(ac, order, alloc_flags,
 				compact_result, &compact_priority,
 				&compaction_retries))
 		goto retry;
 
 
-	/* Deal with possible cpuset update races before we start OOM killing */
-	if (check_retry_cpuset(cpuset_mems_cookie, ac))
-		goto retry_cpuset;
+	/*
+	 * Deal with possible cpuset update races or zonelist updates to avoid
+	 * a unnecessary OOM kill.
+	 */
+	if (check_retry_cpuset(cpuset_mems_cookie, ac) ||
+	    check_retry_zonelist(zonelist_iter_cookie))
+		goto restart;
 
 	/* Reclaim has failed us, start killing things */
 	page = __alloc_pages_may_oom(gfp_mask, order, ac, &did_some_progress);
@@ -5077,9 +5156,13 @@
 	}
 
 nopage:
-	/* Deal with possible cpuset update races before we fail */
-	if (check_retry_cpuset(cpuset_mems_cookie, ac))
-		goto retry_cpuset;
+	/*
+	 * Deal with possible cpuset update races or zonelist updates to avoid
+	 * a unnecessary OOM kill.
+	 */
+	if (check_retry_cpuset(cpuset_mems_cookie, ac) ||
+	    check_retry_zonelist(zonelist_iter_cookie))
+		goto restart;
 
 	/*
 	 * Make sure that __GFP_NOFAIL request doesn't leak out and make sure
@@ -5109,12 +5192,13 @@
 		WARN_ON_ONCE(order > PAGE_ALLOC_COSTLY_ORDER);
 
 		/*
-		 * Help non-failing allocations by giving them access to memory
-		 * reserves but do not use ALLOC_NO_WATERMARKS because this
+		 * Help non-failing allocations by giving some access to memory
+		 * reserves normally used for high priority non-blocking
+		 * allocations but do not use ALLOC_NO_WATERMARKS because this
 		 * could deplete whole memory reserves which would just make
-		 * the situation worse
+		 * the situation worse.
 		 */
-		page = __alloc_pages_cpuset_fallback(gfp_mask, order, ALLOC_HARDER, ac);
+		page = __alloc_pages_cpuset_fallback(gfp_mask, order, ALLOC_MIN_RESERVE, ac);
 		if (page)
 			goto got_pg;
 
@@ -5253,7 +5337,8 @@
 	gfp = alloc_gfp;
 
 	/* Find an allowed local zone that meets the low watermark. */
-	for_each_zone_zonelist_nodemask(zone, z, ac.zonelist, ac.highest_zoneidx, ac.nodemask) {
+	z = ac.preferred_zoneref;
+	for_next_zone_zonelist_nodemask(zone, z, ac.highest_zoneidx, ac.nodemask) {
 		unsigned long mark;
 
 		if (cpusets_enabled() && (alloc_flags & ALLOC_CPUSET) &&
@@ -5297,8 +5382,8 @@
 		page = __rmqueue_pcplist(zone, 0, ac.migratetype, alloc_flags,
 								pcp, pcp_list);
 		if (unlikely(!page)) {
-			/* Try and get at least one page */
-			if (!nr_populated)
+			/* Try and allocate at least one page */
+			if (!nr_account)
 				goto failed_irq;
 			break;
 		}
@@ -5450,9 +5535,12 @@
  */
 void __free_pages(struct page *page, unsigned int order)
 {
+	/* get PageHead before we drop reference */
+	int head = PageHead(page);
+
 	if (put_page_testzero(page))
 		free_the_page(page, order);
-	else if (!PageHead(page))
+	else if (!head)
 		while (order-- > 0)
 			free_the_page(page + (1 << order), order);
 }
@@ -5560,6 +5648,18 @@
 		/* reset page count bias and offset to start of new frag */
 		nc->pagecnt_bias = PAGE_FRAG_CACHE_MAX_SIZE + 1;
 		offset = size - fragsz;
+		if (unlikely(offset < 0)) {
+			/*
+			 * The caller is trying to allocate a fragment
+			 * with fragsz > PAGE_SIZE but the cache isn't big
+			 * enough to satisfy the request, this may
+			 * happen in low memory conditions.
+			 * We don't release the cache page because
+			 * it could make memory pressure worse
+			 * so we simply return NULL here.
+			 */
+			return NULL;
+		}
 	}
 
 	nc->pagecnt_bias--;
@@ -6090,7 +6190,7 @@
 	do {
 		zone_type--;
 		zone = pgdat->node_zones + zone_type;
-		if (managed_zone(zone)) {
+		if (populated_zone(zone)) {
 			zoneref_set_zone(zone, &zonerefs[nr_zones++]);
 			check_highest_zone(zone_type);
 		}
@@ -6361,9 +6461,22 @@
 	int nid;
 	int __maybe_unused cpu;
 	pg_data_t *self = data;
-	static DEFINE_SPINLOCK(lock);
+	unsigned long flags;
 
-	spin_lock(&lock);
+	/*
+	 * Explicitly disable this CPU's interrupts before taking seqlock
+	 * to prevent any IRQ handler from calling into the page allocator
+	 * (e.g. GFP_ATOMIC) that could hit zonelist_iter_begin and livelock.
+	 */
+	local_irq_save(flags);
+	/*
+	 * Explicitly disable this CPU's synchronous printk() before taking
+	 * seqlock to prevent any printk() from trying to hold port->lock, for
+	 * tty_insert_flip_string_and_push_buffer() on other CPU might be
+	 * calling kmalloc(GFP_ATOMIC | __GFP_NOWARN) with port->lock held.
+	 */
+	printk_deferred_enter();
+	write_seqlock(&zonelist_update_seq);
 
 #ifdef CONFIG_NUMA
 	memset(node_load, 0, sizeof(node_load));
@@ -6396,7 +6509,9 @@
 #endif
 	}
 
-	spin_unlock(&lock);
+	write_sequnlock(&zonelist_update_seq);
+	printk_deferred_exit();
+	local_irq_restore(flags);
 }
 
 static noinline void __init
@@ -7897,10 +8012,17 @@
 
 out2:
 	/* Align start of ZONE_MOVABLE on all nids to MAX_ORDER_NR_PAGES */
-	for (nid = 0; nid < MAX_NUMNODES; nid++)
+	for (nid = 0; nid < MAX_NUMNODES; nid++) {
+		unsigned long start_pfn, end_pfn;
+
 		zone_movable_pfn[nid] =
 			roundup(zone_movable_pfn[nid], MAX_ORDER_NR_PAGES);
 
+		get_pfn_range_for_nid(nid, &start_pfn, &end_pfn);
+		if (zone_movable_pfn[nid] >= end_pfn)
+			zone_movable_pfn[nid] = 0;
+	}
+
 out:
 	/* restore the node_state */
 	node_states[N_MEMORY] = saved_node_state;
@@ -8160,7 +8282,7 @@
 	 */
 #define adj_init_size(start, end, size, pos, adj) \
 	do { \
-		if (start <= pos && pos < end && size > adj) \
+		if (&start[0] <= &pos[0] && &pos[0] < &end[0] && size > adj) \
 			size -= adj; \
 	} while (0)
 
@@ -9178,6 +9300,9 @@
 
 		if (PageReserved(page))
 			return false;
+
+		if (PageHuge(page))
+			return false;
 	}
 	return true;
 }
@@ -9401,6 +9526,7 @@
 			next_page = page;
 			current_buddy = page + size;
 		}
+		page = next_page;
 
 		if (set_page_guard(zone, current_buddy, high, migratetype))
 			continue;
@@ -9408,7 +9534,6 @@
 		if (current_buddy != target) {
 			add_to_free_list(current_buddy, zone, high, migratetype);
 			set_buddy_order(current_buddy, high);
-			page = next_page;
 		}
 	}
 }
@@ -9449,3 +9574,18 @@
 	return ret;
 }
 #endif
+
+#ifdef CONFIG_ZONE_DMA
+bool has_managed_dma(void)
+{
+	struct pglist_data *pgdat;
+
+	for_each_online_pgdat(pgdat) {
+		struct zone *zone = &pgdat->node_zones[ZONE_DMA];
+
+		if (managed_zone(zone))
+			return true;
+	}
+	return false;
+}
+#endif /* CONFIG_ZONE_DMA */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/page_io.c
+++ linux-xilinx-zynqmp-5.15.0/mm/page_io.c
@@ -50,54 +50,6 @@
 	bio_put(bio);
 }
 
-static void swap_slot_free_notify(struct page *page)
-{
-	struct swap_info_struct *sis;
-	struct gendisk *disk;
-	swp_entry_t entry;
-
-	/*
-	 * There is no guarantee that the page is in swap cache - the software
-	 * suspend code (at least) uses end_swap_bio_read() against a non-
-	 * swapcache page.  So we must check PG_swapcache before proceeding with
-	 * this optimization.
-	 */
-	if (unlikely(!PageSwapCache(page)))
-		return;
-
-	sis = page_swap_info(page);
-	if (data_race(!(sis->flags & SWP_BLKDEV)))
-		return;
-
-	/*
-	 * The swap subsystem performs lazy swap slot freeing,
-	 * expecting that the page will be swapped out again.
-	 * So we can avoid an unnecessary write if the page
-	 * isn't redirtied.
-	 * This is good for real swap storage because we can
-	 * reduce unnecessary I/O and enhance wear-leveling
-	 * if an SSD is used as the as swap device.
-	 * But if in-memory swap device (eg zram) is used,
-	 * this causes a duplicated copy between uncompressed
-	 * data in VM-owned memory and compressed data in
-	 * zram-owned memory.  So let's free zram-owned memory
-	 * and make the VM-owned decompressed page *dirty*,
-	 * so the page should be swapped out somewhere again if
-	 * we again wish to reclaim it.
-	 */
-	disk = sis->bdev->bd_disk;
-	entry.val = page_private(page);
-	if (disk->fops->swap_slot_free_notify && __swap_count(entry) == 1) {
-		unsigned long offset;
-
-		offset = swp_offset(entry);
-
-		SetPageDirty(page);
-		disk->fops->swap_slot_free_notify(sis->bdev,
-				offset);
-	}
-}
-
 static void end_swap_bio_read(struct bio *bio)
 {
 	struct page *page = bio_first_page_all(bio);
@@ -113,7 +65,6 @@
 	}
 
 	SetPageUptodate(page);
-	swap_slot_free_notify(page);
 out:
 	unlock_page(page);
 	WRITE_ONCE(bio->bi_private, NULL);
@@ -392,11 +343,6 @@
 	if (sis->flags & SWP_SYNCHRONOUS_IO) {
 		ret = bdev_read_page(sis->bdev, swap_page_sector(page), page);
 		if (!ret) {
-			if (trylock_page(page)) {
-				swap_slot_free_notify(page);
-				unlock_page(page);
-			}
-
 			count_vm_event(PSWPIN);
 			goto out;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/mm/pagewalk.c
+++ linux-xilinx-zynqmp-5.15.0/mm/pagewalk.c
@@ -110,7 +110,7 @@
 	do {
 again:
 		next = pmd_addr_end(addr, end);
-		if (pmd_none(*pmd) || (!walk->vma && !walk->no_vma)) {
+		if (pmd_none(*pmd)) {
 			if (ops->pte_hole)
 				err = ops->pte_hole(addr, next, depth, walk);
 			if (err)
@@ -171,7 +171,7 @@
 	do {
  again:
 		next = pud_addr_end(addr, end);
-		if (pud_none(*pud) || (!walk->vma && !walk->no_vma)) {
+		if (pud_none(*pud)) {
 			if (ops->pte_hole)
 				err = ops->pte_hole(addr, next, depth, walk);
 			if (err)
@@ -366,19 +366,19 @@
 	struct vm_area_struct *vma = walk->vma;
 	const struct mm_walk_ops *ops = walk->ops;
 
-	if (vma && ops->pre_vma) {
+	if (ops->pre_vma) {
 		err = ops->pre_vma(start, end, walk);
 		if (err)
 			return err;
 	}
 
-	if (vma && is_vm_hugetlb_page(vma)) {
+	if (is_vm_hugetlb_page(vma)) {
 		if (ops->hugetlb_entry)
 			err = walk_hugetlb_range(start, end, walk);
 	} else
 		err = walk_pgd_range(start, end, walk);
 
-	if (vma && ops->post_vma)
+	if (ops->post_vma)
 		ops->post_vma(walk);
 
 	return err;
@@ -450,9 +450,13 @@
 		if (!vma) { /* after the last vma */
 			walk.vma = NULL;
 			next = end;
+			if (ops->pte_hole)
+				err = ops->pte_hole(start, next, -1, &walk);
 		} else if (start < vma->vm_start) { /* outside vma */
 			walk.vma = NULL;
 			next = min(end, vma->vm_start);
+			if (ops->pte_hole)
+				err = ops->pte_hole(start, next, -1, &walk);
 		} else { /* inside vma */
 			walk.vma = vma;
 			next = min(end, vma->vm_end);
@@ -470,9 +474,8 @@
 			}
 			if (err < 0)
 				break;
-		}
-		if (walk.vma || walk.ops->pte_hole)
 			err = __walk_page_range(start, next, &walk);
+		}
 		if (err)
 			break;
 	} while (start = next, start < end);
@@ -501,9 +504,9 @@
 	if (start >= end || !walk.mm)
 		return -EINVAL;
 
-	mmap_assert_locked(walk.mm);
+	mmap_assert_write_locked(walk.mm);
 
-	return __walk_page_range(start, end, &walk);
+	return walk_pgd_range(start, end, &walk);
 }
 
 int walk_page_vma(struct vm_area_struct *vma, const struct mm_walk_ops *ops,
--- linux-xilinx-zynqmp-5.15.0.orig/mm/percpu-internal.h
+++ linux-xilinx-zynqmp-5.15.0/mm/percpu-internal.h
@@ -40,10 +40,17 @@
 	struct list_head	list;		/* linked to pcpu_slot lists */
 	int			free_bytes;	/* free bytes in the chunk */
 	struct pcpu_block_md	chunk_md;
-	void			*base_addr;	/* base address of this chunk */
+	unsigned long		*bound_map;	/* boundary map */
+
+	/*
+	 * base_addr is the base address of this chunk.
+	 * To reduce false sharing, current layout is optimized to make sure
+	 * base_addr locate in the different cacheline with free_bytes and
+	 * chunk_md.
+	 */
+	void			*base_addr ____cacheline_aligned_in_smp;
 
 	unsigned long		*alloc_map;	/* allocation map */
-	unsigned long		*bound_map;	/* boundary map */
 	struct pcpu_block_md	*md_blocks;	/* metadata blocks */
 
 	void			*data;		/* chunk data */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/percpu.c
+++ linux-xilinx-zynqmp-5.15.0/mm/percpu.c
@@ -2472,7 +2472,7 @@
  */
 void __init pcpu_free_alloc_info(struct pcpu_alloc_info *ai)
 {
-	memblock_free_early(__pa(ai), ai->__ai_size);
+	memblock_free(__pa(ai), ai->__ai_size);
 }
 
 /**
@@ -3134,7 +3134,7 @@
 out_free:
 	pcpu_free_alloc_info(ai);
 	if (areas)
-		memblock_free_early(__pa(areas), areas_size);
+		memblock_free(__pa(areas), areas_size);
 	return rc;
 }
 #endif /* BUILD_EMBED_FIRST_CHUNK */
@@ -3256,7 +3256,7 @@
 		free_fn(page_address(pages[j]), PAGE_SIZE);
 	rc = -ENOMEM;
 out_free_ar:
-	memblock_free_early(__pa(pages), pages_size);
+	memblock_free(__pa(pages), pages_size);
 	pcpu_free_alloc_info(ai);
 	return rc;
 }
@@ -3286,7 +3286,7 @@
 
 static void __init pcpu_dfl_fc_free(void *ptr, size_t size)
 {
-	memblock_free_early(__pa(ptr), size);
+	memblock_free(__pa(ptr), size);
 }
 
 void __init setup_per_cpu_areas(void)
--- linux-xilinx-zynqmp-5.15.0.orig/mm/prfile.c
+++ linux-xilinx-zynqmp-5.15.0/mm/prfile.c
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Mainly for aufs which mmap(2) different file and wants to print different
+ * path in /proc/PID/maps.
+ * Call these functions via macros defined in linux/mm.h.
+ *
+ * See Documentation/filesystems/aufs/design/06mmap.txt
+ *
+ * Copyright (c) 2014-2021 Junjro R. Okajima
+ * Copyright (c) 2014 Ian Campbell
+ */
+
+#include <linux/mm.h>
+#include <linux/file.h>
+#include <linux/fs.h>
+
+/* #define PRFILE_TRACE */
+static inline void prfile_trace(struct file *f, struct file *pr,
+			      const char func[], int line, const char func2[])
+{
+#ifdef PRFILE_TRACE
+	if (pr)
+		pr_info("%s:%d: %s, %pD2\n", func, line, func2, f);
+#endif
+}
+
+void vma_do_file_update_time(struct vm_area_struct *vma, const char func[],
+			     int line)
+{
+	struct file *f = vma->vm_file, *pr = vma->vm_prfile;
+
+	prfile_trace(f, pr, func, line, __func__);
+	file_update_time(f);
+	if (f && pr)
+		file_update_time(pr);
+}
+
+struct file *vma_do_pr_or_file(struct vm_area_struct *vma, const char func[],
+			       int line)
+{
+	struct file *f = vma->vm_file, *pr = vma->vm_prfile;
+
+	prfile_trace(f, pr, func, line, __func__);
+	return (f && pr) ? pr : f;
+}
+
+void vma_do_get_file(struct vm_area_struct *vma, const char func[], int line)
+{
+	struct file *f = vma->vm_file, *pr = vma->vm_prfile;
+
+	prfile_trace(f, pr, func, line, __func__);
+	get_file(f);
+	if (f && pr)
+		get_file(pr);
+}
+
+void vma_do_fput(struct vm_area_struct *vma, const char func[], int line)
+{
+	struct file *f = vma->vm_file, *pr = vma->vm_prfile;
+
+	prfile_trace(f, pr, func, line, __func__);
+	fput(f);
+	if (f && pr)
+		fput(pr);
+}
+
+#ifndef CONFIG_MMU
+struct file *vmr_do_pr_or_file(struct vm_region *region, const char func[],
+			       int line)
+{
+	struct file *f = region->vm_file, *pr = region->vm_prfile;
+
+	prfile_trace(f, pr, func, line, __func__);
+	return (f && pr) ? pr : f;
+}
+
+void vmr_do_fput(struct vm_region *region, const char func[], int line)
+{
+	struct file *f = region->vm_file, *pr = region->vm_prfile;
+
+	prfile_trace(f, pr, func, line, __func__);
+	fput(f);
+	if (f && pr)
+		fput(pr);
+}
+#endif /* !CONFIG_MMU */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/ptdump.c
+++ linux-xilinx-zynqmp-5.15.0/mm/ptdump.c
@@ -144,13 +144,13 @@
 {
 	const struct ptdump_range *range = st->range;
 
-	mmap_read_lock(mm);
+	mmap_write_lock(mm);
 	while (range->start != range->end) {
 		walk_page_range_novma(mm, range->start, range->end,
 				      &ptdump_ops, pgd, st);
 		range++;
 	}
-	mmap_read_unlock(mm);
+	mmap_write_unlock(mm);
 
 	/* Flush out the last page */
 	st->note_page(st, 0, -1, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/readahead.c
+++ linux-xilinx-zynqmp-5.15.0/mm/readahead.c
@@ -627,7 +627,8 @@
 	 */
 	ret = -EINVAL;
 	if (!f.file->f_mapping || !f.file->f_mapping->a_ops ||
-	    !S_ISREG(file_inode(f.file)->i_mode))
+	    (!S_ISREG(file_inode(f.file)->i_mode) &&
+	    !S_ISBLK(file_inode(f.file)->i_mode)))
 		goto out;
 
 	ret = vfs_fadvise(f.file, offset, count, POSIX_FADV_WILLNEED);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/rmap.c
+++ linux-xilinx-zynqmp-5.15.0/mm/rmap.c
@@ -90,7 +90,8 @@
 	anon_vma = kmem_cache_alloc(anon_vma_cachep, GFP_KERNEL);
 	if (anon_vma) {
 		atomic_set(&anon_vma->refcount, 1);
-		anon_vma->degree = 1;	/* Reference for first vma */
+		anon_vma->num_children = 0;
+		anon_vma->num_active_vmas = 0;
 		anon_vma->parent = anon_vma;
 		/*
 		 * Initialise the anon_vma root to point to itself. If called
@@ -198,6 +199,7 @@
 		anon_vma = anon_vma_alloc();
 		if (unlikely(!anon_vma))
 			goto out_enomem_free_avc;
+		anon_vma->num_children++; /* self-parent link for new root */
 		allocated = anon_vma;
 	}
 
@@ -207,8 +209,7 @@
 	if (likely(!vma->anon_vma)) {
 		vma->anon_vma = anon_vma;
 		anon_vma_chain_link(vma, avc, anon_vma);
-		/* vma reference or self-parent link for new root */
-		anon_vma->degree++;
+		anon_vma->num_active_vmas++;
 		allocated = NULL;
 		avc = NULL;
 	}
@@ -293,19 +294,19 @@
 		anon_vma_chain_link(dst, avc, anon_vma);
 
 		/*
-		 * Reuse existing anon_vma if its degree lower than two,
-		 * that means it has no vma and only one anon_vma child.
+		 * Reuse existing anon_vma if it has no vma and only one
+		 * anon_vma child.
 		 *
-		 * Do not chose parent anon_vma, otherwise first child
-		 * will always reuse it. Root anon_vma is never reused:
+		 * Root anon_vma is never reused:
 		 * it has self-parent reference and at least one child.
 		 */
 		if (!dst->anon_vma && src->anon_vma &&
-		    anon_vma != src->anon_vma && anon_vma->degree < 2)
+		    anon_vma->num_children < 2 &&
+		    anon_vma->num_active_vmas == 0)
 			dst->anon_vma = anon_vma;
 	}
 	if (dst->anon_vma)
-		dst->anon_vma->degree++;
+		dst->anon_vma->num_active_vmas++;
 	unlock_anon_vma_root(root);
 	return 0;
 
@@ -355,6 +356,7 @@
 	anon_vma = anon_vma_alloc();
 	if (!anon_vma)
 		goto out_error;
+	anon_vma->num_active_vmas++;
 	avc = anon_vma_chain_alloc(GFP_KERNEL);
 	if (!avc)
 		goto out_error_free_anon_vma;
@@ -375,7 +377,7 @@
 	vma->anon_vma = anon_vma;
 	anon_vma_lock_write(anon_vma);
 	anon_vma_chain_link(vma, avc, anon_vma);
-	anon_vma->parent->degree++;
+	anon_vma->parent->num_children++;
 	anon_vma_unlock_write(anon_vma);
 
 	return 0;
@@ -407,7 +409,7 @@
 		 * to free them outside the lock.
 		 */
 		if (RB_EMPTY_ROOT(&anon_vma->rb_root.rb_root)) {
-			anon_vma->parent->degree--;
+			anon_vma->parent->num_children--;
 			continue;
 		}
 
@@ -415,7 +417,7 @@
 		anon_vma_chain_free(avc);
 	}
 	if (vma->anon_vma) {
-		vma->anon_vma->degree--;
+		vma->anon_vma->num_active_vmas--;
 
 		/*
 		 * vma would still be needed after unlink, and anon_vma will be prepared
@@ -433,7 +435,8 @@
 	list_for_each_entry_safe(avc, next, &vma->anon_vma_chain, same_vma) {
 		struct anon_vma *anon_vma = avc->anon_vma;
 
-		VM_WARN_ON(anon_vma->degree);
+		VM_WARN_ON(anon_vma->num_children);
+		VM_WARN_ON(anon_vma->num_active_vmas);
 		put_anon_vma(anon_vma);
 
 		list_del(&avc->same_vma);
@@ -1570,7 +1573,30 @@
 
 			/* MADV_FREE page check */
 			if (!PageSwapBacked(page)) {
-				if (!PageDirty(page)) {
+				int ref_count, map_count;
+
+				/*
+				 * Synchronize with gup_pte_range():
+				 * - clear PTE; barrier; read refcount
+				 * - inc refcount; barrier; read PTE
+				 */
+				smp_mb();
+
+				ref_count = page_ref_count(page);
+				map_count = page_mapcount(page);
+
+				/*
+				 * Order reads for page refcount and dirty flag
+				 * (see comments in __remove_mapping()).
+				 */
+				smp_rmb();
+
+				/*
+				 * The only page refs must be one from isolation
+				 * plus the rmap(s) (dropped by discard:).
+				 */
+				if (ref_count == 1 + map_count &&
+				    !PageDirty(page)) {
 					/* Invalidate as we cleared the pte */
 					mmu_notifier_invalidate_range(mm,
 						address, address + PAGE_SIZE);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/secretmem.c
+++ linux-xilinx-zynqmp-5.15.0/mm/secretmem.c
@@ -55,22 +55,28 @@
 	gfp_t gfp = vmf->gfp_mask;
 	unsigned long addr;
 	struct page *page;
+	vm_fault_t ret;
 	int err;
 
 	if (((loff_t)vmf->pgoff << PAGE_SHIFT) >= i_size_read(inode))
 		return vmf_error(-EINVAL);
 
+	filemap_invalidate_lock_shared(mapping);
+
 retry:
 	page = find_lock_page(mapping, offset);
 	if (!page) {
 		page = alloc_page(gfp | __GFP_ZERO);
-		if (!page)
-			return VM_FAULT_OOM;
+		if (!page) {
+			ret = VM_FAULT_OOM;
+			goto out;
+		}
 
 		err = set_direct_map_invalid_noflush(page);
 		if (err) {
 			put_page(page);
-			return vmf_error(err);
+			ret = vmf_error(err);
+			goto out;
 		}
 
 		__SetPageUptodate(page);
@@ -86,7 +92,8 @@
 			if (err == -EEXIST)
 				goto retry;
 
-			return vmf_error(err);
+			ret = vmf_error(err);
+			goto out;
 		}
 
 		addr = (unsigned long)page_address(page);
@@ -94,7 +101,11 @@
 	}
 
 	vmf->page = page;
-	return VM_FAULT_LOCKED;
+	ret = VM_FAULT_LOCKED;
+
+out:
+	filemap_invalidate_unlock_shared(mapping);
+	return ret;
 }
 
 static const struct vm_operations_struct secretmem_vm_ops = {
@@ -158,6 +169,30 @@
 	.isolate_page	= secretmem_isolate_page,
 };
 
+static int secretmem_setattr(struct user_namespace *mnt_userns,
+			     struct dentry *dentry, struct iattr *iattr)
+{
+	struct inode *inode = d_inode(dentry);
+	struct address_space *mapping = inode->i_mapping;
+	unsigned int ia_valid = iattr->ia_valid;
+	int ret;
+
+	filemap_invalidate_lock(mapping);
+
+	if ((ia_valid & ATTR_SIZE) && inode->i_size)
+		ret = -EINVAL;
+	else
+		ret = simple_setattr(mnt_userns, dentry, iattr);
+
+	filemap_invalidate_unlock(mapping);
+
+	return ret;
+}
+
+static const struct inode_operations secretmem_iops = {
+	.setattr = secretmem_setattr,
+};
+
 static struct vfsmount *secretmem_mnt;
 
 static struct file *secretmem_file_create(unsigned long flags)
@@ -177,6 +212,7 @@
 	mapping_set_gfp_mask(inode->i_mapping, GFP_HIGHUSER);
 	mapping_set_unevictable(inode->i_mapping);
 
+	inode->i_op = &secretmem_iops;
 	inode->i_mapping->a_ops = &secretmem_aops;
 
 	/* pretend we are a normal file with zero size */
@@ -198,7 +234,7 @@
 	/* make sure local flags do not confict with global fcntl.h */
 	BUILD_BUG_ON(SECRETMEM_FLAGS_MASK & O_CLOEXEC);
 
-	if (!secretmem_enable)
+	if (!secretmem_enable || !can_set_direct_map())
 		return -ENOSYS;
 
 	if (flags & ~(SECRETMEM_FLAGS_MASK | O_CLOEXEC))
@@ -242,12 +278,12 @@
 {
 	int ret = 0;
 
-	if (!secretmem_enable)
+	if (!secretmem_enable || !can_set_direct_map())
 		return ret;
 
 	secretmem_mnt = kern_mount(&secretmem_fs);
 	if (IS_ERR(secretmem_mnt))
-		ret = PTR_ERR(secretmem_mnt);
+		return PTR_ERR(secretmem_mnt);
 
 	/* prevent secretmem mappings from ever getting PROT_EXEC */
 	secretmem_mnt->mnt_flags |= MNT_NOEXEC;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/shmem.c
+++ linux-xilinx-zynqmp-5.15.0/mm/shmem.c
@@ -555,7 +555,7 @@
 	struct shmem_inode_info *info;
 	struct page *page;
 	unsigned long batch = sc ? sc->nr_to_scan : 128;
-	int removed = 0, split = 0;
+	int split = 0;
 
 	if (list_empty(&sbinfo->shrinklist))
 		return SHRINK_STOP;
@@ -570,7 +570,6 @@
 		/* inode is about to be evicted */
 		if (!inode) {
 			list_del_init(&info->shrinklist);
-			removed++;
 			goto next;
 		}
 
@@ -578,12 +577,12 @@
 		if (round_up(inode->i_size, PAGE_SIZE) ==
 				round_up(inode->i_size, HPAGE_PMD_SIZE)) {
 			list_move(&info->shrinklist, &to_remove);
-			removed++;
 			goto next;
 		}
 
 		list_move(&info->shrinklist, &list);
 next:
+		sbinfo->shrinklist_len--;
 		if (!--batch)
 			break;
 	}
@@ -603,7 +602,7 @@
 		inode = &info->vfs_inode;
 
 		if (nr_to_split && split >= nr_to_split)
-			goto leave;
+			goto move_back;
 
 		page = find_get_page(inode->i_mapping,
 				(inode->i_size & HPAGE_PMD_MASK) >> PAGE_SHIFT);
@@ -617,38 +616,44 @@
 		}
 
 		/*
-		 * Leave the inode on the list if we failed to lock
-		 * the page at this time.
+		 * Move the inode on the list back to shrinklist if we failed
+		 * to lock the page at this time.
 		 *
 		 * Waiting for the lock may lead to deadlock in the
 		 * reclaim path.
 		 */
 		if (!trylock_page(page)) {
 			put_page(page);
-			goto leave;
+			goto move_back;
 		}
 
 		ret = split_huge_page(page);
 		unlock_page(page);
 		put_page(page);
 
-		/* If split failed leave the inode on the list */
+		/* If split failed move the inode on the list back to shrinklist */
 		if (ret)
-			goto leave;
+			goto move_back;
 
 		split++;
 drop:
 		list_del_init(&info->shrinklist);
-		removed++;
-leave:
+		goto put;
+move_back:
+		/*
+		 * Make sure the inode is either on the global list or deleted
+		 * from any local list before iput() since it could be deleted
+		 * in another thread once we put the inode (then the local list
+		 * is corrupted).
+		 */
+		spin_lock(&sbinfo->shrinklist_lock);
+		list_move(&info->shrinklist, &sbinfo->shrinklist);
+		sbinfo->shrinklist_len++;
+		spin_unlock(&sbinfo->shrinklist_lock);
+put:
 		iput(inode);
 	}
 
-	spin_lock(&sbinfo->shrinklist_lock);
-	list_splice_tail(&list, &sbinfo->shrinklist);
-	sbinfo->shrinklist_len -= removed;
-	spin_unlock(&sbinfo->shrinklist_lock);
-
 	return split;
 }
 
@@ -2261,9 +2266,6 @@
 	if (ret)
 		return ret;
 
-	/* arm64 - allow memory tagging on RAM-based files */
-	vma->vm_flags |= VM_MTE_ALLOWED;
-
 	file_accessed(file);
 	vma->vm_ops = &shmem_vm_ops;
 	if (IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE) &&
@@ -2389,8 +2391,10 @@
 				/* don't free the page */
 				goto out_unacct_blocks;
 			}
+
+			flush_dcache_page(page);
 		} else {		/* ZEROPAGE */
-			clear_highpage(page);
+			clear_user_highpage(page, dst_addr);
 		}
 	} else {
 		page = *pagep;
@@ -2456,6 +2460,7 @@
 	struct inode *inode = mapping->host;
 	struct shmem_inode_info *info = SHMEM_I(inode);
 	pgoff_t index = pos >> PAGE_SHIFT;
+	int ret = 0;
 
 	/* i_rwsem is held by caller */
 	if (unlikely(info->seals & (F_SEAL_GROW |
@@ -2466,7 +2471,19 @@
 			return -EPERM;
 	}
 
-	return shmem_getpage(inode, index, pagep, SGP_WRITE);
+	ret = shmem_getpage(inode, index, pagep, SGP_WRITE);
+
+	if (ret)
+		return ret;
+
+	if (PageHWPoison(*pagep)) {
+		unlock_page(*pagep);
+		put_page(*pagep);
+		*pagep = NULL;
+		return -EIO;
+	}
+
+	return 0;
 }
 
 static int
@@ -2553,6 +2570,12 @@
 			if (sgp == SGP_CACHE)
 				set_page_dirty(page);
 			unlock_page(page);
+
+			if (PageHWPoison(page)) {
+				put_page(page);
+				error = -EIO;
+				break;
+			}
 		}
 
 		/*
@@ -3114,7 +3137,8 @@
 		page = find_get_page(inode->i_mapping, 0);
 		if (!page)
 			return ERR_PTR(-ECHILD);
-		if (!PageUptodate(page)) {
+		if (PageHWPoison(page) ||
+		    !PageUptodate(page)) {
 			put_page(page);
 			return ERR_PTR(-ECHILD);
 		}
@@ -3122,6 +3146,13 @@
 		error = shmem_getpage(inode, 0, &page, SGP_READ);
 		if (error)
 			return ERR_PTR(error);
+		if (!page)
+			return ERR_PTR(-ECHILD);
+		if (PageHWPoison(page)) {
+			unlock_page(page);
+			put_page(page);
+			return ERR_PTR(-ECHILD);
+		}
 		unlock_page(page);
 	}
 	set_delayed_call(done, shmem_put_link, page);
@@ -3360,6 +3391,8 @@
 	unsigned long long size;
 	char *rest;
 	int opt;
+	kuid_t kuid;
+	kgid_t kgid;
 
 	opt = fs_parse(fc, shmem_fs_parameters, param, &result);
 	if (opt < 0)
@@ -3395,14 +3428,32 @@
 		ctx->mode = result.uint_32 & 07777;
 		break;
 	case Opt_uid:
-		ctx->uid = make_kuid(current_user_ns(), result.uint_32);
-		if (!uid_valid(ctx->uid))
+		kuid = make_kuid(current_user_ns(), result.uint_32);
+		if (!uid_valid(kuid))
+			goto bad_value;
+
+		/*
+		 * The requested uid must be representable in the
+		 * filesystem's idmapping.
+		 */
+		if (!kuid_has_mapping(fc->user_ns, kuid))
 			goto bad_value;
+
+		ctx->uid = kuid;
 		break;
 	case Opt_gid:
-		ctx->gid = make_kgid(current_user_ns(), result.uint_32);
-		if (!gid_valid(ctx->gid))
+		kgid = make_kgid(current_user_ns(), result.uint_32);
+		if (!gid_valid(kgid))
+			goto bad_value;
+
+		/*
+		 * The requested gid must be representable in the
+		 * filesystem's idmapping.
+		 */
+		if (!kgid_has_mapping(fc->user_ns, kgid))
 			goto bad_value;
+
+		ctx->gid = kgid;
 		break;
 	case Opt_huge:
 		ctx->huge = result.uint_32;
@@ -3772,6 +3823,13 @@
 	kmem_cache_destroy(shmem_inode_cachep);
 }
 
+/* Keep the page in page cache instead of truncating it */
+static int shmem_error_remove_page(struct address_space *mapping,
+				   struct page *page)
+{
+	return 0;
+}
+
 const struct address_space_operations shmem_aops = {
 	.writepage	= shmem_writepage,
 	.set_page_dirty	= __set_page_dirty_no_writeback,
@@ -3782,7 +3840,7 @@
 #ifdef CONFIG_MIGRATION
 	.migratepage	= migrate_page,
 #endif
-	.error_remove_page = generic_error_remove_page,
+	.error_remove_page = shmem_error_remove_page,
 };
 EXPORT_SYMBOL(shmem_aops);
 
@@ -4002,7 +4060,7 @@
 	.name		= "tmpfs",
 	.init_fs_context = ramfs_init_fs_context,
 	.parameters	= ramfs_fs_parameters,
-	.kill_sb	= kill_litter_super,
+	.kill_sb	= ramfs_kill_sb,
 	.fs_flags	= FS_USERNS_MOUNT,
 };
 
@@ -4162,6 +4220,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(shmem_zero_setup);
 
 /**
  * shmem_read_mapping_page_gfp - read into page cache, using specified page allocation flags.
@@ -4190,9 +4249,14 @@
 	error = shmem_getpage_gfp(inode, index, &page, SGP_CACHE,
 				  gfp, NULL, NULL, NULL);
 	if (error)
-		page = ERR_PTR(error);
-	else
-		unlock_page(page);
+		return ERR_PTR(error);
+
+	unlock_page(page);
+	if (PageHWPoison(page)) {
+		put_page(page);
+		return ERR_PTR(-EIO);
+	}
+
 	return page;
 #else
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/mm/slab.c
+++ linux-xilinx-zynqmp-5.15.0/mm/slab.c
@@ -855,7 +855,7 @@
 	return 0;
 }
 
-#if (defined(CONFIG_NUMA) && defined(CONFIG_MEMORY_HOTPLUG)) || defined(CONFIG_SMP)
+#if defined(CONFIG_NUMA) || defined(CONFIG_SMP)
 /*
  * Allocates and initializes node for a node on each slab cache, used for
  * either memory or cpu hotplug.  If memory is being hot-added, the kmem_cache_node
@@ -3429,6 +3429,7 @@
 
 	if (is_kfence_address(objp)) {
 		kmemleak_free_recursive(objp, cachep->flags);
+		memcg_slab_free_hook(cachep, &objp, 1);
 		__kfence_free(objp);
 		return;
 	}
@@ -3657,7 +3658,7 @@
 #endif /* CONFIG_NUMA */
 
 #ifdef CONFIG_PRINTK
-void kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
+void __kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
 {
 	struct kmem_cache *cachep;
 	unsigned int objnr;
@@ -4225,11 +4226,14 @@
 #endif /* CONFIG_HARDENED_USERCOPY */
 
 /**
- * __ksize -- Uninstrumented ksize.
+ * __ksize -- Report full size of underlying allocation
  * @objp: pointer to the object
  *
- * Unlike ksize(), __ksize() is uninstrumented, and does not provide the same
- * safety checks as ksize() with KASAN instrumentation enabled.
+ * This should only be used internally to query the true size of allocations.
+ * It is not meant to be a way to discover the usable size of an allocation
+ * after the fact. Instead, use kmalloc_size_roundup(). Using memory beyond
+ * the originally requested allocation size may trigger KASAN, UBSAN_BOUNDS,
+ * and/or FORTIFY_SOURCE.
  *
  * Return: size of the actual memory used by @objp in bytes
  */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/slab.h
+++ linux-xilinx-zynqmp-5.15.0/mm/slab.h
@@ -147,7 +147,7 @@
 #define SLAB_CACHE_FLAGS (SLAB_NOLEAKTRACE | SLAB_RECLAIM_ACCOUNT | \
 			  SLAB_TEMPORARY | SLAB_ACCOUNT)
 #else
-#define SLAB_CACHE_FLAGS (0)
+#define SLAB_CACHE_FLAGS (SLAB_NOLEAKTRACE)
 #endif
 
 /* Common flags available with current configuration */
@@ -643,7 +643,7 @@
 	void *kp_stack[KS_ADDRS_COUNT];
 	void *kp_free_stack[KS_ADDRS_COUNT];
 };
-void kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page);
+void __kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page);
 #endif
 
 #endif /* MM_SLAB_H */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/slab_common.c
+++ linux-xilinx-zynqmp-5.15.0/mm/slab_common.c
@@ -568,6 +568,13 @@
 }
 EXPORT_SYMBOL_GPL(kmem_valid_obj);
 
+static void kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
+{
+	if (__kfence_obj_info(kpp, object, page))
+		return;
+	__kmem_obj_info(kpp, object, page);
+}
+
 /**
  * kmem_dump_obj - Print available slab provenance information
  * @object: slab object for which to find provenance information.
@@ -603,6 +610,8 @@
 		pr_cont(" slab%s %s", cp, kp.kp_slab_cache->name);
 	else
 		pr_cont(" slab%s", cp);
+	if (is_kfence_address(object))
+		pr_cont(" (kfence)");
 	if (kp.kp_objp)
 		pr_cont(" start %px", kp.kp_objp);
 	if (kp.kp_data_offset)
@@ -749,6 +758,26 @@
 	return kmalloc_caches[kmalloc_type(flags)][index];
 }
 
+size_t kmalloc_size_roundup(size_t size)
+{
+	struct kmem_cache *c;
+
+	/* Short-circuit the 0 size case. */
+	if (unlikely(size == 0))
+		return 0;
+	/* Short-circuit saturated "too-large" case. */
+	if (unlikely(size == SIZE_MAX))
+		return SIZE_MAX;
+	/* Above the smaller buckets, size is a multiple of page size. */
+	if (size > KMALLOC_MAX_CACHE_SIZE)
+		return PAGE_SIZE << get_order(size);
+
+	/* The flags don't matter since size_index is common to all. */
+	c = kmalloc_slab(size, GFP_KERNEL);
+	return c ? c->object_size : 0;
+}
+EXPORT_SYMBOL(kmalloc_size_roundup);
+
 #ifdef CONFIG_ZONE_DMA
 #define KMALLOC_DMA_NAME(sz)	.name[KMALLOC_DMA] = "dma-kmalloc-" #sz,
 #else
@@ -1201,6 +1230,13 @@
 
 	/* If the object still fits, repoison it precisely. */
 	if (ks >= new_size) {
+		/* Zero out spare memory. */
+		if (want_init_on_alloc(flags)) {
+			kasan_disable_current();
+			memset(kasan_reset_tag(p) + new_size, 0, ks - new_size);
+			kasan_enable_current();
+		}
+
 		p = kasan_krealloc((void *)p, new_size, flags);
 		return (void *)p;
 	}
@@ -1269,20 +1305,6 @@
 }
 EXPORT_SYMBOL(kfree_sensitive);
 
-/**
- * ksize - get the actual amount of memory allocated for a given object
- * @objp: Pointer to the object
- *
- * kmalloc may internally round up allocations and return more memory
- * than requested. ksize() can be used to determine the actual amount of
- * memory allocated. The caller may use this additional memory, even though
- * a smaller amount of memory was initially specified with the kmalloc call.
- * The caller must guarantee that objp points to a valid object previously
- * allocated with either kmalloc() or kmem_cache_alloc(). The object
- * must not be freed during the duration of the call.
- *
- * Return: size of the actual memory used by @objp in bytes
- */
 size_t ksize(const void *objp)
 {
 	size_t size;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/slob.c
+++ linux-xilinx-zynqmp-5.15.0/mm/slob.c
@@ -462,7 +462,7 @@
 }
 
 #ifdef CONFIG_PRINTK
-void kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
+void __kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
 {
 	kpp->kp_ptr = object;
 	kpp->kp_page = page;
@@ -567,6 +567,20 @@
 }
 EXPORT_SYMBOL(kfree);
 
+size_t kmalloc_size_roundup(size_t size)
+{
+	/* Short-circuit the 0 size case. */
+	if (unlikely(size == 0))
+		return 0;
+	/* Short-circuit saturated "too-large" case. */
+	if (unlikely(size == SIZE_MAX))
+		return SIZE_MAX;
+
+	return ALIGN(size, ARCH_KMALLOC_MINALIGN);
+}
+
+EXPORT_SYMBOL(kmalloc_size_roundup);
+
 /* can't use ksize for kmem_cache_alloc memory, only kmalloc */
 size_t __ksize(const void *block)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/mm/slub.c
+++ linux-xilinx-zynqmp-5.15.0/mm/slub.c
@@ -308,6 +308,11 @@
  */
 static nodemask_t slab_nodes;
 
+/*
+ * Workqueue used for flush_cpu_slab().
+ */
+static struct workqueue_struct *flushwq;
+
 /********************************************************************
  * 			Core slab cache functions
  *******************************************************************/
@@ -2688,7 +2693,7 @@
 		INIT_WORK(&sfw->work, flush_cpu_slab);
 		sfw->skip = false;
 		sfw->s = s;
-		schedule_work_on(cpu, &sfw->work);
+		queue_work_on(cpu, flushwq, &sfw->work);
 	}
 
 	for_each_online_cpu(cpu) {
@@ -2935,6 +2940,7 @@
 
 	if (!freelist) {
 		c->page = NULL;
+		c->tid = next_tid(c->tid);
 		local_unlock_irqrestore(&s->cpu_slab->lock, flags);
 		stat(s, DEACTIVATE_BYPASS);
 		goto new_slab;
@@ -2967,6 +2973,7 @@
 	freelist = c->freelist;
 	c->page = NULL;
 	c->freelist = NULL;
+	c->tid = next_tid(c->tid);
 	local_unlock_irqrestore(&s->cpu_slab->lock, flags);
 	deactivate_slab(s, page, freelist);
 
@@ -4299,7 +4306,7 @@
 }
 
 #ifdef CONFIG_PRINTK
-void kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
+void __kmem_obj_info(struct kmem_obj_info *kpp, void *object, struct page *page)
 {
 	void *base;
 	int __maybe_unused i;
@@ -4848,6 +4855,8 @@
 
 void __init kmem_cache_init_late(void)
 {
+	flushwq = alloc_workqueue("slub_flushwq", WQ_MEM_RECLAIM, 0);
+	WARN_ON(!flushwq);
 }
 
 struct kmem_cache *
@@ -4918,6 +4927,8 @@
 	/* Honor the call site pointer we received. */
 	trace_kmalloc(caller, ret, size, s->size, gfpflags);
 
+	ret = kasan_kmalloc(s, ret, size, gfpflags);
+
 	return ret;
 }
 EXPORT_SYMBOL(__kmalloc_track_caller);
@@ -4949,6 +4960,8 @@
 	/* Honor the call site pointer we received. */
 	trace_kmalloc_node(caller, ret, size, s->size, gfpflags, node);
 
+	ret = kasan_kmalloc(s, ret, size, gfpflags);
+
 	return ret;
 }
 EXPORT_SYMBOL(__kmalloc_node_track_caller);
@@ -5072,6 +5085,7 @@
 	unsigned long max;
 	unsigned long count;
 	struct location *loc;
+	loff_t idx;
 };
 
 static struct dentry *slab_debugfs_root;
@@ -5862,7 +5876,8 @@
 	char *name = kmalloc(ID_STR_LENGTH, GFP_KERNEL);
 	char *p = name;
 
-	BUG_ON(!name);
+	if (!name)
+		return ERR_PTR(-ENOMEM);
 
 	*p++ = ':';
 	/*
@@ -5920,6 +5935,8 @@
 		 * for the symlinks.
 		 */
 		name = create_unique_id(s);
+		if (IS_ERR(name))
+			return PTR_ERR(name);
 	}
 
 	s->kobj.kset = kset;
@@ -6035,11 +6052,11 @@
 #if defined(CONFIG_SLUB_DEBUG) && defined(CONFIG_DEBUG_FS)
 static int slab_debugfs_show(struct seq_file *seq, void *v)
 {
-
-	struct location *l;
-	unsigned int idx = *(unsigned int *)v;
 	struct loc_track *t = seq->private;
+	struct location *l;
+	unsigned long idx;
 
+	idx = (unsigned long) t->idx;
 	if (idx < t->count) {
 		l = &t->loc[idx];
 
@@ -6088,16 +6105,18 @@
 {
 	struct loc_track *t = seq->private;
 
-	v = ppos;
-	++*ppos;
+	t->idx = ++(*ppos);
 	if (*ppos <= t->count)
-		return v;
+		return ppos;
 
 	return NULL;
 }
 
 static void *slab_debugfs_start(struct seq_file *seq, loff_t *ppos)
 {
+	struct loc_track *t = seq->private;
+
+	t->idx = *ppos;
 	return ppos;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/mm/sparse.c
+++ linux-xilinx-zynqmp-5.15.0/mm/sparse.c
@@ -451,7 +451,7 @@
 static inline void __meminit sparse_buffer_free(unsigned long size)
 {
 	WARN_ON(!sparsemap_buf || size == 0);
-	memblock_free_early(__pa(sparsemap_buf), size);
+	memblock_free(__pa(sparsemap_buf), size);
 }
 
 static void __init sparse_buffer_init(unsigned long size, int nid)
@@ -790,6 +790,13 @@
 		unsigned long section_nr = pfn_to_section_nr(pfn);
 
 		/*
+		 * Mark the section invalid so that valid_section()
+		 * return false. This prevents code from dereferencing
+		 * ms->usage array.
+		 */
+		ms->section_mem_map &= ~SECTION_HAS_MEM_MAP;
+
+		/*
 		 * When removing an early section, the usage map is kept (as the
 		 * usage maps of other sections fall into the same page). It
 		 * will be re-used when re-adding the section - which is then no
@@ -797,16 +804,10 @@
 		 * was allocated during boot.
 		 */
 		if (!PageReserved(virt_to_page(ms->usage))) {
-			kfree(ms->usage);
-			ms->usage = NULL;
+			kfree_rcu(ms->usage, rcu);
+			WRITE_ONCE(ms->usage, NULL);
 		}
 		memmap = sparse_decode_mem_map(ms->section_mem_map, section_nr);
-		/*
-		 * Mark the section invalid so that valid_section()
-		 * return false. This prevents code from dereferencing
-		 * ms->usage array.
-		 */
-		ms->section_mem_map &= ~SECTION_HAS_MEM_MAP;
 	}
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/mm/swap_state.c
+++ linux-xilinx-zynqmp-5.15.0/mm/swap_state.c
@@ -38,7 +38,7 @@
 
 struct address_space *swapper_spaces[MAX_SWAPFILES] __read_mostly;
 static unsigned int nr_swapper_spaces[MAX_SWAPFILES] __read_mostly;
-static bool enable_vma_readahead __read_mostly = true;
+static bool enable_vma_readahead __read_mostly = false;
 
 #define SWAP_RA_WIN_SHIFT	(PAGE_SHIFT / 2)
 #define SWAP_RA_HITS_MASK	((1UL << SWAP_RA_WIN_SHIFT) - 1)
@@ -478,7 +478,7 @@
 		 * __read_swap_cache_async(), which has set SWAP_HAS_CACHE
 		 * in swap_map, but not yet added its page to swap cache.
 		 */
-		cond_resched();
+		schedule_timeout_uninterruptible(1);
 	}
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/mm/swapfile.c
+++ linux-xilinx-zynqmp-5.15.0/mm/swapfile.c
@@ -673,6 +673,7 @@
 {
 	int nid;
 
+	assert_spin_locked(&p->lock);
 	for_each_node(nid)
 		plist_del(&p->avail_lists[nid], &swap_avail_heads[nid]);
 }
@@ -1093,6 +1094,7 @@
 			goto check_out;
 		pr_debug("scan_swap_map of si %d failed to find offset\n",
 			si->type);
+		cond_resched();
 
 		spin_lock(&swap_avail_lock);
 nextsi:
@@ -1234,6 +1236,18 @@
 }
 
 /*
+ * When we get a swap entry, if there aren't some other ways to
+ * prevent swapoff, such as the folio in swap cache is locked, page
+ * table lock is held, etc., the swap entry may become invalid because
+ * of swapoff.  Then, we need to enclose all swap related functions
+ * with get_swap_device() and put_swap_device(), unless the swap
+ * functions call get/put_swap_device() by themselves.
+ *
+ * Note that when only holding the PTL, swapoff might succeed immediately
+ * after freeing a swap entry. Therefore, immediately after
+ * __swap_entry_free(), the swap info might become stale and should not
+ * be touched without a prior get_swap_device().
+ *
  * Check whether swap entry is valid in the swap device.  If so,
  * return pointer to swap_info_struct, and keep the swap entry valid
  * via preventing the swap device from being swapoff, until
@@ -1242,9 +1256,8 @@
  * Notice that swapoff or swapoff+swapon can still happen before the
  * percpu_ref_tryget_live() in get_swap_device() or after the
  * percpu_ref_put() in put_swap_device() if there isn't any other way
- * to prevent swapoff, such as page lock, page table lock, etc.  The
- * caller must be prepared for that.  For example, the following
- * situation is possible.
+ * to prevent swapoff.  The caller must be prepared for that.  For
+ * example, the following situation is possible.
  *
  *   CPU1				CPU2
  *   do_swap_page()
@@ -1760,13 +1773,19 @@
 	if (non_swap_entry(entry))
 		return 1;
 
-	p = _swap_info_get(entry);
+	p = get_swap_device(entry);
 	if (p) {
+		if (WARN_ON(data_race(!p->swap_map[swp_offset(entry)]))) {
+			put_swap_device(p);
+			return 0;
+		}
+
 		count = __swap_entry_free(p, entry);
 		if (count == SWAP_HAS_CACHE &&
 		    !swap_page_trans_huge_swapped(p, entry))
 			__try_to_reclaim_swap(p, swp_offset(entry),
 					      TTRS_UNMAPPED | TTRS_FULL);
+		put_swap_device(p);
 	}
 	return p != NULL;
 }
@@ -2106,7 +2125,7 @@
 
 	mmap_read_lock(mm);
 	for (vma = mm->mmap; vma; vma = vma->vm_next) {
-		if (vma->anon_vma) {
+		if (vma->anon_vma && !is_vm_hugetlb_page(vma)) {
 			ret = unuse_vma(vma, type, frontswap,
 					fs_pages_to_unuse);
 			if (ret)
@@ -2564,8 +2583,8 @@
 		spin_unlock(&swap_lock);
 		goto out_dput;
 	}
-	del_from_avail_list(p);
 	spin_lock(&p->lock);
+	del_from_avail_list(p);
 	if (p->prio < 0) {
 		struct swap_info_struct *si = p;
 		int nid;
--- linux-xilinx-zynqmp-5.15.0.orig/mm/usercopy.c
+++ linux-xilinx-zynqmp-5.15.0/mm/usercopy.c
@@ -294,7 +294,10 @@
 
 static int __init parse_hardened_usercopy(char *str)
 {
-	return strtobool(str, &enable_checks);
+	if (strtobool(str, &enable_checks))
+		pr_warn("Invalid option string for hardened_usercopy: '%s'\n",
+			str);
+	return 1;
 }
 
 __setup("hardened_usercopy=", parse_hardened_usercopy);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/userfaultfd.c
+++ linux-xilinx-zynqmp-5.15.0/mm/userfaultfd.c
@@ -63,7 +63,7 @@
 	pte_t _dst_pte, *dst_pte;
 	bool writable = dst_vma->vm_flags & VM_WRITE;
 	bool vm_shared = dst_vma->vm_flags & VM_SHARED;
-	bool page_in_cache = page->mapping;
+	bool page_in_cache = page_mapping(page);
 	spinlock_t *ptl;
 	struct inode *inode;
 	pgoff_t offset, max_off;
@@ -151,6 +151,8 @@
 			/* don't free the page */
 			goto out;
 		}
+
+		flush_dcache_page(page);
 	} else {
 		page = *pagep;
 		*pagep = NULL;
@@ -225,7 +227,10 @@
 	struct page *page;
 	int ret;
 
-	ret = shmem_getpage(inode, pgoff, &page, SGP_READ);
+	ret = shmem_getpage(inode, pgoff, &page, SGP_NOALLOC);
+	/* Our caller expects us to return -EFAULT if we failed to find page. */
+	if (ret == -ENOENT)
+		ret = -EFAULT;
 	if (ret)
 		goto out;
 	if (!page) {
@@ -233,6 +238,11 @@
 		goto out;
 	}
 
+	if (PageHWPoison(page)) {
+		ret = -EIO;
+		goto out_release;
+	}
+
 	ret = mfill_atomic_install_pte(dst_mm, dst_pmd, dst_vma, dst_addr,
 				       page, false, wp_copy);
 	if (ret)
@@ -279,6 +289,7 @@
 					      unsigned long dst_start,
 					      unsigned long src_start,
 					      unsigned long len,
+					      atomic_t *mmap_changing,
 					      enum mcopy_atomic_mode mode)
 {
 	int vm_shared = dst_vma->vm_flags & VM_SHARED;
@@ -395,6 +406,15 @@
 				goto out;
 			}
 			mmap_read_lock(dst_mm);
+			/*
+			 * If memory mappings are changing because of non-cooperative
+			 * operation (e.g. mremap) running in parallel, bail out and
+			 * request the user to retry later
+			 */
+			if (mmap_changing && atomic_read(mmap_changing)) {
+				err = -EAGAIN;
+				break;
+			}
 
 			dst_vma = NULL;
 			goto retry;
@@ -430,6 +450,7 @@
 				      unsigned long dst_start,
 				      unsigned long src_start,
 				      unsigned long len,
+				      atomic_t *mmap_changing,
 				      enum mcopy_atomic_mode mode);
 #endif /* CONFIG_HUGETLB_PAGE */
 
@@ -551,7 +572,8 @@
 	 */
 	if (is_vm_hugetlb_page(dst_vma))
 		return  __mcopy_atomic_hugetlb(dst_mm, dst_vma, dst_start,
-						src_start, len, mcopy_mode);
+					       src_start, len, mmap_changing,
+					       mcopy_mode);
 
 	if (!vma_is_anonymous(dst_vma) && !vma_is_shmem(dst_vma))
 		goto out_unlock;
@@ -621,6 +643,7 @@
 				err = -EFAULT;
 				goto out;
 			}
+			flush_dcache_page(page);
 			goto retry;
 		} else
 			BUG_ON(page);
--- linux-xilinx-zynqmp-5.15.0.orig/mm/util.c
+++ linux-xilinx-zynqmp-5.15.0/mm/util.c
@@ -343,6 +343,38 @@
 #endif
 }
 
+/**
+ * randomize_page - Generate a random, page aligned address
+ * @start:	The smallest acceptable address the caller will take.
+ * @range:	The size of the area, starting at @start, within which the
+ *		random address must fall.
+ *
+ * If @start + @range would overflow, @range is capped.
+ *
+ * NOTE: Historical use of randomize_range, which this replaces, presumed that
+ * @start was already page aligned.  We now align it regardless.
+ *
+ * Return: A page aligned address within [start, start + range).  On error,
+ * @start is returned.
+ */
+unsigned long randomize_page(unsigned long start, unsigned long range)
+{
+	if (!PAGE_ALIGNED(start)) {
+		range -= PAGE_ALIGN(start) - start;
+		start = PAGE_ALIGN(start);
+	}
+
+	if (start > ULONG_MAX - range)
+		range = ULONG_MAX - start;
+
+	range >>= PAGE_SHIFT;
+
+	if (range == 0)
+		return start;
+
+	return start + (get_random_long() % range << PAGE_SHIFT);
+}
+
 #ifdef CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT
 unsigned long arch_randomize_brk(struct mm_struct *mm)
 {
@@ -398,7 +430,7 @@
 	if (gap + pad > gap)
 		gap += pad;
 
-	if (gap < MIN_GAP)
+	if (gap < MIN_GAP && MIN_GAP < MAX_GAP)
 		gap = MIN_GAP;
 	else if (gap > MAX_GAP)
 		gap = MAX_GAP;
@@ -594,8 +626,10 @@
 		return ret;
 
 	/* Don't even allow crazy sizes */
-	if (WARN_ON_ONCE(size > INT_MAX))
+	if (unlikely(size > INT_MAX)) {
+		WARN_ON_ONCE(!(flags & __GFP_NOWARN));
 		return NULL;
+	}
 
 	return __vmalloc_node(size, 1, flags, node,
 			__builtin_return_address(0));
@@ -664,6 +698,56 @@
 	return (void *)mapping;
 }
 
+/**
+ * __vmalloc_array - allocate memory for a virtually contiguous array.
+ * @n: number of elements.
+ * @size: element size.
+ * @flags: the type of memory to allocate (see kmalloc).
+ */
+void *__vmalloc_array(size_t n, size_t size, gfp_t flags)
+{
+	size_t bytes;
+
+	if (unlikely(check_mul_overflow(n, size, &bytes)))
+		return NULL;
+	return __vmalloc(bytes, flags);
+}
+EXPORT_SYMBOL(__vmalloc_array);
+
+/**
+ * vmalloc_array - allocate memory for a virtually contiguous array.
+ * @n: number of elements.
+ * @size: element size.
+ */
+void *vmalloc_array(size_t n, size_t size)
+{
+	return __vmalloc_array(n, size, GFP_KERNEL);
+}
+EXPORT_SYMBOL(vmalloc_array);
+
+/**
+ * __vcalloc - allocate and zero memory for a virtually contiguous array.
+ * @n: number of elements.
+ * @size: element size.
+ * @flags: the type of memory to allocate (see kmalloc).
+ */
+void *__vcalloc(size_t n, size_t size, gfp_t flags)
+{
+	return __vmalloc_array(n, size, flags | __GFP_ZERO);
+}
+EXPORT_SYMBOL(__vcalloc);
+
+/**
+ * vcalloc - allocate and zero memory for a virtually contiguous array.
+ * @n: number of elements.
+ * @size: element size.
+ */
+void *vcalloc(size_t n, size_t size)
+{
+	return __vmalloc_array(n, size, GFP_KERNEL | __GFP_ZERO);
+}
+EXPORT_SYMBOL(vcalloc);
+
 /* Neutral page->mapping pointer to address_space or anon_vma or other */
 void *page_rmapping(struct page *page)
 {
@@ -1002,6 +1086,39 @@
 	return ret;
 }
 
+int mmap_file(struct file *file, struct vm_area_struct *vma)
+{
+	static const struct vm_operations_struct dummy_vm_ops = {};
+	int err = call_mmap(file, vma);
+
+	if (likely(!err))
+		return 0;
+
+	/*
+	 * OK, we tried to call the file hook for mmap(), but an error
+	 * arose. The mapping is in an inconsistent state and we most not invoke
+	 * any further hooks on it.
+	 */
+	vma->vm_ops = &dummy_vm_ops;
+
+	return err;
+}
+
+void vma_close(struct vm_area_struct *vma)
+{
+	static const struct vm_operations_struct dummy_vm_ops = {};
+
+	if (vma->vm_ops && vma->vm_ops->close) {
+		vma->vm_ops->close(vma);
+
+		/*
+		 * The mapping is in an inconsistent state, and no further hooks
+		 * may be invoked upon it.
+		 */
+		vma->vm_ops = &dummy_vm_ops;
+	}
+}
+
 #ifdef CONFIG_PRINTK
 /**
  * mem_dump_obj - Print available provenance information
@@ -1026,7 +1143,9 @@
 	if (vmalloc_dump_obj(object))
 		return;
 
-	if (virt_addr_valid(object))
+	if (is_vmalloc_addr(object))
+		type = "vmalloc memory";
+	else if (virt_addr_valid(object))
 		type = "non-slab/vmalloc memory";
 	else if (object == NULL)
 		type = "NULL pointer";
--- linux-xilinx-zynqmp-5.15.0.orig/mm/vmalloc.c
+++ linux-xilinx-zynqmp-5.15.0/mm/vmalloc.c
@@ -556,13 +556,13 @@
 			mask |= PGTBL_PGD_MODIFIED;
 		err = vmap_pages_p4d_range(pgd, addr, next, prot, pages, &nr, &mask);
 		if (err)
-			return err;
+			break;
 	} while (pgd++, addr = next, addr != end);
 
 	if (mask & ARCH_PAGE_TABLE_SYNC_MASK)
 		arch_sync_kernel_mappings(start, end);
 
-	return 0;
+	return err;
 }
 
 /*
@@ -2459,6 +2459,7 @@
 				  NUMA_NO_NODE, GFP_KERNEL,
 				  __builtin_return_address(0));
 }
+EXPORT_SYMBOL(get_vm_area);
 
 struct vm_struct *get_vm_area_caller(unsigned long size, unsigned long flags,
 				const void *caller)
@@ -2621,7 +2622,8 @@
 			__free_pages(page, page_order);
 			cond_resched();
 		}
-		atomic_long_sub(area->nr_pages, &nr_vmalloc_pages);
+		if (!(area->flags & VM_MAP_PUT_PAGES))
+			atomic_long_sub(area->nr_pages, &nr_vmalloc_pages);
 
 		kvfree(area->pages);
 	}
@@ -2806,6 +2808,10 @@
 		free_vm_area(area);
 		return NULL;
 	}
+
+	flush_cache_vmap((unsigned long)area->addr,
+			 (unsigned long)area->addr + count * PAGE_SIZE);
+
 	return area->addr;
 }
 EXPORT_SYMBOL_GPL(vmap_pfn);
@@ -2927,9 +2933,11 @@
 	 * allocation request, free them via __vfree() if any.
 	 */
 	if (area->nr_pages != nr_small_pages) {
-		warn_alloc(gfp_mask, NULL,
-			"vmalloc error: size %lu, page order %u, failed to allocate pages",
-			area->nr_pages * PAGE_SIZE, page_order);
+		/* vm_area_alloc_pages() can also fail due to a fatal signal */
+		if (!fatal_signal_pending(current))
+			warn_alloc(gfp_mask, NULL,
+				"vmalloc error: size %lu, page order %u, failed to allocate pages",
+				area->nr_pages * PAGE_SIZE, page_order);
 		goto fail;
 	}
 
@@ -3032,7 +3040,8 @@
 	clear_vm_uninitialized_flag(area);
 
 	size = PAGE_ALIGN(size);
-	kmemleak_vmalloc(area, size, gfp_mask);
+	if (!(vm_flags & VM_DEFER_KMEMLEAK))
+		kmemleak_vmalloc(area, size, gfp_mask);
 
 	return addr;
 
@@ -3816,14 +3825,32 @@
 #ifdef CONFIG_PRINTK
 bool vmalloc_dump_obj(void *object)
 {
-	struct vm_struct *vm;
 	void *objp = (void *)PAGE_ALIGN((unsigned long)object);
+	const void *caller;
+	struct vm_struct *vm;
+	struct vmap_area *va;
+	unsigned long addr;
+	unsigned int nr_pages;
 
-	vm = find_vm_area(objp);
-	if (!vm)
+	if (!spin_trylock(&vmap_area_lock))
+		return false;
+	va = __find_vmap_area((unsigned long)objp);
+	if (!va) {
+		spin_unlock(&vmap_area_lock);
 		return false;
+	}
+
+	vm = va->vm;
+	if (!vm) {
+		spin_unlock(&vmap_area_lock);
+		return false;
+	}
+	addr = (unsigned long)vm->addr;
+	caller = vm->caller;
+	nr_pages = vm->nr_pages;
+	spin_unlock(&vmap_area_lock);
 	pr_cont(" %u-page vmalloc region starting at %#lx allocated at %pS\n",
-		vm->nr_pages, (unsigned long)vm->addr, vm->caller);
+		nr_pages, addr, caller);
 	return true;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/mm/vmpressure.c
+++ linux-xilinx-zynqmp-5.15.0/mm/vmpressure.c
@@ -244,6 +244,14 @@
 	if (mem_cgroup_disabled())
 		return;
 
+	/*
+	 * The in-kernel users only care about the reclaim efficiency
+	 * for this @memcg rather than the whole subtree, and there
+	 * isn't and won't be any in-kernel user in a legacy cgroup.
+	 */
+	if (!cgroup_subsys_on_dfl(memory_cgrp_subsys) && !tree)
+		return;
+
 	vmpr = memcg_to_vmpressure(memcg);
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/mm/vmscan.c
+++ linux-xilinx-zynqmp-5.15.0/mm/vmscan.c
@@ -578,7 +578,14 @@
 	if (can_reclaim_anon_pages(NULL, zone_to_nid(zone), NULL))
 		nr += zone_page_state_snapshot(zone, NR_ZONE_INACTIVE_ANON) +
 			zone_page_state_snapshot(zone, NR_ZONE_ACTIVE_ANON);
-
+	/*
+	 * If there are no reclaimable file-backed or anonymous pages,
+	 * ensure zones with sufficient free pages are not skipped.
+	 * This prevents zones like DMA32 from being ignored in reclaim
+	 * scenarios where they can still help alleviate memory pressure.
+	 */
+	if (nr == 0)
+		nr = zone_page_state_snapshot(zone, NR_FREE_PAGES);
 	return nr;
 }
 
@@ -1866,69 +1873,6 @@
 }
 
 /*
- * Attempt to remove the specified page from its LRU.  Only take this page
- * if it is of the appropriate PageActive status.  Pages which are being
- * freed elsewhere are also ignored.
- *
- * page:	page to consider
- * mode:	one of the LRU isolation modes defined above
- *
- * returns true on success, false on failure.
- */
-bool __isolate_lru_page_prepare(struct page *page, isolate_mode_t mode)
-{
-	/* Only take pages on the LRU. */
-	if (!PageLRU(page))
-		return false;
-
-	/* Compaction should not handle unevictable pages but CMA can do so */
-	if (PageUnevictable(page) && !(mode & ISOLATE_UNEVICTABLE))
-		return false;
-
-	/*
-	 * To minimise LRU disruption, the caller can indicate that it only
-	 * wants to isolate pages it will be able to operate on without
-	 * blocking - clean pages for the most part.
-	 *
-	 * ISOLATE_ASYNC_MIGRATE is used to indicate that it only wants to pages
-	 * that it is possible to migrate without blocking
-	 */
-	if (mode & ISOLATE_ASYNC_MIGRATE) {
-		/* All the caller can do on PageWriteback is block */
-		if (PageWriteback(page))
-			return false;
-
-		if (PageDirty(page)) {
-			struct address_space *mapping;
-			bool migrate_dirty;
-
-			/*
-			 * Only pages without mappings or that have a
-			 * ->migratepage callback are possible to migrate
-			 * without blocking. However, we can be racing with
-			 * truncation so it's necessary to lock the page
-			 * to stabilise the mapping as truncation holds
-			 * the page lock until after the page is removed
-			 * from the page cache.
-			 */
-			if (!trylock_page(page))
-				return false;
-
-			mapping = page_mapping(page);
-			migrate_dirty = !mapping || mapping->a_ops->migratepage;
-			unlock_page(page);
-			if (!migrate_dirty)
-				return false;
-		}
-	}
-
-	if ((mode & ISOLATE_UNMAPPED) && page_mapped(page))
-		return false;
-
-	return true;
-}
-
-/*
  * Update LRU sizes after isolating pages. The LRU size updates must
  * be complete before mem_cgroup_update_lru_size due to a sanity check.
  */
@@ -1979,11 +1923,11 @@
 	unsigned long skipped = 0;
 	unsigned long scan, total_scan, nr_pages;
 	LIST_HEAD(pages_skipped);
-	isolate_mode_t mode = (sc->may_unmap ? 0 : ISOLATE_UNMAPPED);
 
 	total_scan = 0;
 	scan = 0;
 	while (scan < nr_to_scan && !list_empty(src)) {
+		struct list_head *move_to = src;
 		struct page *page;
 
 		page = lru_to_page(src);
@@ -1993,9 +1937,9 @@
 		total_scan += nr_pages;
 
 		if (page_zonenum(page) > sc->reclaim_idx) {
-			list_move(&page->lru, &pages_skipped);
 			nr_skipped[page_zonenum(page)] += nr_pages;
-			continue;
+			move_to = &pages_skipped;
+			goto move;
 		}
 
 		/*
@@ -2003,37 +1947,34 @@
 		 * return with no isolated pages if the LRU mostly contains
 		 * ineligible pages.  This causes the VM to not reclaim any
 		 * pages, triggering a premature OOM.
-		 *
-		 * Account all tail pages of THP.  This would not cause
-		 * premature OOM since __isolate_lru_page() returns -EBUSY
-		 * only when the page is being freed somewhere else.
+		 * Account all tail pages of THP.
 		 */
 		scan += nr_pages;
-		if (!__isolate_lru_page_prepare(page, mode)) {
-			/* It is being freed elsewhere */
-			list_move(&page->lru, src);
-			continue;
-		}
+
+		if (!PageLRU(page))
+			goto move;
+		if (!sc->may_unmap && page_mapped(page))
+			goto move;
+
 		/*
 		 * Be careful not to clear PageLRU until after we're
 		 * sure the page is not being freed elsewhere -- the
 		 * page release code relies on it.
 		 */
-		if (unlikely(!get_page_unless_zero(page))) {
-			list_move(&page->lru, src);
-			continue;
-		}
+		if (unlikely(!get_page_unless_zero(page)))
+			goto move;
 
 		if (!TestClearPageLRU(page)) {
 			/* Another thread is already isolating this page */
 			put_page(page);
-			list_move(&page->lru, src);
-			continue;
+			goto move;
 		}
 
 		nr_taken += nr_pages;
 		nr_zone_taken[page_zonenum(page)] += nr_pages;
-		list_move(&page->lru, dst);
+		move_to = dst;
+move:
+		list_move(&page->lru, move_to);
 	}
 
 	/*
@@ -2057,7 +1998,8 @@
 	}
 	*nr_scanned = total_scan;
 	trace_mm_vmscan_lru_isolate(sc->reclaim_idx, sc->order, nr_to_scan,
-				    total_scan, skipped, nr_taken, mode, lru);
+				    total_scan, skipped, nr_taken,
+				    sc->may_unmap ? 0 : ISOLATE_UNMAPPED, lru);
 	update_lru_sizes(lruvec, lru, nr_zone_taken);
 	return nr_taken;
 }
@@ -2791,8 +2733,8 @@
 	enum lru_list lru;
 	unsigned long nr_reclaimed = 0;
 	unsigned long nr_to_reclaim = sc->nr_to_reclaim;
+	bool proportional_reclaim;
 	struct blk_plug plug;
-	bool scan_adjusted;
 
 	get_scan_count(lruvec, sc, nr);
 
@@ -2810,8 +2752,8 @@
 	 * abort proportional reclaim if either the file or anon lru has already
 	 * dropped to zero at the first pass.
 	 */
-	scan_adjusted = (!cgroup_reclaim(sc) && !current_is_kswapd() &&
-			 sc->priority == DEF_PRIORITY);
+	proportional_reclaim = (!cgroup_reclaim(sc) && !current_is_kswapd() &&
+				sc->priority == DEF_PRIORITY);
 
 	blk_start_plug(&plug);
 	while (nr[LRU_INACTIVE_ANON] || nr[LRU_ACTIVE_FILE] ||
@@ -2831,7 +2773,7 @@
 
 		cond_resched();
 
-		if (nr_reclaimed < nr_to_reclaim || scan_adjusted)
+		if (nr_reclaimed < nr_to_reclaim || proportional_reclaim)
 			continue;
 
 		/*
@@ -2882,8 +2824,6 @@
 		nr_scanned = targets[lru] - nr[lru];
 		nr[lru] = targets[lru] * (100 - percentage) / 100;
 		nr[lru] -= min(nr[lru], nr_scanned);
-
-		scan_adjusted = true;
 	}
 	blk_finish_plug(&plug);
 	sc->nr_reclaimed += nr_reclaimed;
@@ -2901,7 +2841,7 @@
 /* Use reclaim/compaction for costly allocs or under memory pressure */
 static bool in_reclaim_compaction(struct scan_control *sc)
 {
-	if (IS_ENABLED(CONFIG_COMPACTION) && sc->order &&
+	if (gfp_compaction_allowed(sc->gfp_mask) && sc->order &&
 			(sc->order > PAGE_ALLOC_COSTLY_ORDER ||
 			 sc->priority < DEF_PRIORITY - 2))
 		return true;
@@ -3234,6 +3174,9 @@
 	unsigned long watermark;
 	enum compact_result suitable;
 
+	if (!gfp_compaction_allowed(sc->gfp_mask))
+		return false;
+
 	suitable = compaction_suitable(zone, sc->order, 0, sc->reclaim_idx);
 	if (suitable == COMPACT_SUCCESS)
 		/* Allocation should succeed already. Don't reclaim. */
--- linux-xilinx-zynqmp-5.15.0.orig/mm/vmstat.c
+++ linux-xilinx-zynqmp-5.15.0/mm/vmstat.c
@@ -1690,6 +1690,7 @@
 			   zone_page_state(zone, i));
 
 #ifdef CONFIG_NUMA
+	fold_vm_zone_numa_events(zone);
 	for (i = 0; i < NR_VM_NUMA_EVENT_ITEMS; i++)
 		seq_printf(m, "\n      %-12s %lu", numa_stat_name(i),
 			   zone_numa_event_state(zone, i));
--- linux-xilinx-zynqmp-5.15.0.orig/mm/workingset.c
+++ linux-xilinx-zynqmp-5.15.0/mm/workingset.c
@@ -352,7 +352,7 @@
 
 	inc_lruvec_state(lruvec, WORKINGSET_REFAULT_BASE + file);
 
-	mem_cgroup_flush_stats();
+	mem_cgroup_flush_stats_delayed();
 	/*
 	 * Compare the distance to the existing workingset size. We
 	 * don't activate pages that couldn't stay resident even if
--- linux-xilinx-zynqmp-5.15.0.orig/mm/zsmalloc.c
+++ linux-xilinx-zynqmp-5.15.0/mm/zsmalloc.c
@@ -1743,11 +1743,40 @@
  */
 static void lock_zspage(struct zspage *zspage)
 {
-	struct page *page = get_first_page(zspage);
+	struct page *curr_page, *page;
 
-	do {
-		lock_page(page);
-	} while ((page = get_next_page(page)) != NULL);
+	/*
+	 * Pages we haven't locked yet can be migrated off the list while we're
+	 * trying to lock them, so we need to be careful and only attempt to
+	 * lock each page under migrate_read_lock(). Otherwise, the page we lock
+	 * may no longer belong to the zspage. This means that we may wait for
+	 * the wrong page to unlock, so we must take a reference to the page
+	 * prior to waiting for it to unlock outside migrate_read_lock().
+	 */
+	while (1) {
+		migrate_read_lock(zspage);
+		page = get_first_page(zspage);
+		if (trylock_page(page))
+			break;
+		get_page(page);
+		migrate_read_unlock(zspage);
+		wait_on_page_locked(page);
+		put_page(page);
+	}
+
+	curr_page = page;
+	while ((page = get_next_page(curr_page))) {
+		if (trylock_page(page)) {
+			curr_page = page;
+		} else {
+			get_page(page);
+			migrate_read_unlock(zspage);
+			wait_on_page_locked(page);
+			put_page(page);
+			migrate_read_lock(zspage);
+		}
+	}
+	migrate_read_unlock(zspage);
 }
 
 static int zs_init_fs_context(struct fs_context *fc)
@@ -1830,10 +1859,11 @@
 	VM_BUG_ON(atomic_long_read(&pool->isolated_pages) <= 0);
 	atomic_long_dec(&pool->isolated_pages);
 	/*
-	 * There's no possibility of racing, since wait_for_isolated_drain()
-	 * checks the isolated count under &class->lock after enqueuing
-	 * on migration_wait.
+	 * Checking pool->destroying must happen after atomic_long_dec()
+	 * for pool->isolated_pages above. Paired with the smp_mb() in
+	 * zs_unregister_migration().
 	 */
+	smp_mb__after_atomic();
 	if (atomic_long_read(&pool->isolated_pages) == 0 && pool->destroying)
 		wake_up_all(&pool->migration_wait);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/802/mrp.c
+++ linux-xilinx-zynqmp-5.15.0/net/802/mrp.c
@@ -606,7 +606,10 @@
 	spin_unlock(&app->lock);
 
 	mrp_queue_xmit(app);
-	mrp_join_timer_arm(app);
+	spin_lock(&app->lock);
+	if (likely(app->active))
+		mrp_join_timer_arm(app);
+	spin_unlock(&app->lock);
 }
 
 static void mrp_periodic_timer_arm(struct mrp_applicant *app)
@@ -620,11 +623,12 @@
 	struct mrp_applicant *app = from_timer(app, t, periodic_timer);
 
 	spin_lock(&app->lock);
-	mrp_mad_event(app, MRP_EVENT_PERIODIC);
-	mrp_pdu_queue(app);
+	if (likely(app->active)) {
+		mrp_mad_event(app, MRP_EVENT_PERIODIC);
+		mrp_pdu_queue(app);
+		mrp_periodic_timer_arm(app);
+	}
 	spin_unlock(&app->lock);
-
-	mrp_periodic_timer_arm(app);
 }
 
 static int mrp_pdu_parse_end_mark(struct sk_buff *skb, int *offset)
@@ -872,6 +876,7 @@
 	app->dev = dev;
 	app->app = appl;
 	app->mad = RB_ROOT;
+	app->active = true;
 	spin_lock_init(&app->lock);
 	skb_queue_head_init(&app->queue);
 	rcu_assign_pointer(dev->mrp_port->applicants[appl->type], app);
@@ -900,6 +905,9 @@
 
 	RCU_INIT_POINTER(port->applicants[appl->type], NULL);
 
+	spin_lock_bh(&app->lock);
+	app->active = false;
+	spin_unlock_bh(&app->lock);
 	/* Delete timer and generate a final TX event to flush out
 	 * all pending messages before the applicant is gone.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/net/802/psnap.c
+++ linux-xilinx-zynqmp-5.15.0/net/802/psnap.c
@@ -55,11 +55,11 @@
 		goto drop;
 
 	rcu_read_lock();
-	proto = find_snap_client(skb_transport_header(skb));
+	proto = find_snap_client(skb->data);
 	if (proto) {
 		/* Pass the frame on. */
-		skb->transport_header += 5;
 		skb_pull_rcsum(skb, 5);
+		skb_reset_transport_header(skb);
 		rc = proto->rcvfunc(skb, dev, &snap_packet_type, orig_dev);
 	}
 	rcu_read_unlock();
--- linux-xilinx-zynqmp-5.15.0.orig/net/8021q/vlan.c
+++ linux-xilinx-zynqmp-5.15.0/net/8021q/vlan.c
@@ -123,9 +123,6 @@
 	}
 
 	vlan_vid_del(real_dev, vlan->vlan_proto, vlan_id);
-
-	/* Get rid of the vlan's reference to real_dev */
-	dev_put(real_dev);
 }
 
 int vlan_check_real_dev(struct net_device *real_dev,
@@ -134,7 +131,8 @@
 {
 	const char *name = real_dev->name;
 
-	if (real_dev->features & NETIF_F_VLAN_CHALLENGED) {
+	if (real_dev->features & NETIF_F_VLAN_CHALLENGED ||
+	    real_dev->type != ARPHRD_ETHER) {
 		pr_info("VLANs not supported on %s\n", name);
 		NL_SET_ERR_MSG_MOD(extack, "VLANs not supported on device");
 		return -EOPNOTSUPP;
@@ -187,9 +185,6 @@
 	if (err)
 		goto out_unregister_netdev;
 
-	/* Account for reference in struct vlan_dev_priv */
-	dev_hold(real_dev);
-
 	vlan_stacked_transfer_operstate(real_dev, dev, vlan);
 	linkwatch_fire_event(dev); /* _MUST_ call rfc2863_policy() */
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/8021q/vlan.h
+++ linux-xilinx-zynqmp-5.15.0/net/8021q/vlan.h
@@ -129,6 +129,7 @@
 				   u32 skb_prio, u16 vlan_prio);
 int vlan_dev_set_egress_priority(const struct net_device *dev,
 				 u32 skb_prio, u16 vlan_prio);
+void vlan_dev_free_egress_priority(const struct net_device *dev);
 int vlan_dev_change_flags(const struct net_device *dev, u32 flag, u32 mask);
 void vlan_dev_get_realdev_name(const struct net_device *dev, char *result,
 			       size_t size);
@@ -139,7 +140,6 @@
 void vlan_setup(struct net_device *dev);
 int register_vlan_dev(struct net_device *dev, struct netlink_ext_ack *extack);
 void unregister_vlan_dev(struct net_device *dev, struct list_head *head);
-void vlan_dev_uninit(struct net_device *dev);
 bool vlan_dev_inherit_address(struct net_device *dev,
 			      struct net_device *real_dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/8021q/vlan_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/8021q/vlan_core.c
@@ -407,6 +407,8 @@
 		return 0;
 
 	list_for_each_entry(vid_info, &vlan_info->vid_list, list) {
+		if (!vlan_hw_filter_capable(by_dev, vid_info->proto))
+			continue;
 		err = vlan_vid_add(dev, vid_info->proto, vid_info->vid);
 		if (err)
 			goto unwind;
@@ -417,6 +419,8 @@
 	list_for_each_entry_continue_reverse(vid_info,
 					     &vlan_info->vid_list,
 					     list) {
+		if (!vlan_hw_filter_capable(by_dev, vid_info->proto))
+			continue;
 		vlan_vid_del(dev, vid_info->proto, vid_info->vid);
 	}
 
@@ -436,8 +440,11 @@
 	if (!vlan_info)
 		return;
 
-	list_for_each_entry(vid_info, &vlan_info->vid_list, list)
+	list_for_each_entry(vid_info, &vlan_info->vid_list, list) {
+		if (!vlan_hw_filter_capable(by_dev, vid_info->proto))
+			continue;
 		vlan_vid_del(dev, vid_info->proto, vid_info->vid);
+	}
 }
 EXPORT_SYMBOL(vlan_vids_del_by_dev);
 
@@ -476,10 +483,9 @@
 
 	type = vhdr->h_vlan_encapsulated_proto;
 
-	rcu_read_lock();
 	ptype = gro_find_receive_by_type(type);
 	if (!ptype)
-		goto out_unlock;
+		goto out;
 
 	flush = 0;
 
@@ -501,8 +507,6 @@
 					    ipv6_gro_receive, inet_gro_receive,
 					    head, skb);
 
-out_unlock:
-	rcu_read_unlock();
 out:
 	skb_gro_flush_final(skb, pp, flush);
 
@@ -516,14 +520,12 @@
 	struct packet_offload *ptype;
 	int err = -ENOENT;
 
-	rcu_read_lock();
 	ptype = gro_find_complete_by_type(type);
 	if (ptype)
 		err = INDIRECT_CALL_INET(ptype->callbacks.gro_complete,
 					 ipv6_gro_complete, inet_gro_complete,
 					 skb, nhoff + sizeof(*vhdr));
 
-	rcu_read_unlock();
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/8021q/vlan_dev.c
+++ linux-xilinx-zynqmp-5.15.0/net/8021q/vlan_dev.c
@@ -108,8 +108,8 @@
 	 * NOTE: THIS ASSUMES DIX ETHERNET, SPECIFICALLY NOT SUPPORTING
 	 * OTHER THINGS LIKE FDDI/TokenRing/802.3 SNAPs...
 	 */
-	if (veth->h_vlan_proto != vlan->vlan_proto ||
-	    vlan->flags & VLAN_FLAG_REORDER_HDR) {
+	if (vlan->flags & VLAN_FLAG_REORDER_HDR ||
+	    veth->h_vlan_proto != vlan->vlan_proto) {
 		u16 vlan_tci;
 		vlan_tci = vlan->vlan_id;
 		vlan_tci |= vlan_dev_get_egress_qos_mask(dev, skb->priority);
@@ -250,7 +250,7 @@
 	if (dev->addr_assign_type != NET_ADDR_STOLEN)
 		return false;
 
-	ether_addr_copy(dev->dev_addr, real_dev->dev_addr);
+	eth_hw_addr_set(dev, real_dev->dev_addr);
 	call_netdevice_notifiers(NETDEV_CHANGEADDR, dev);
 	return true;
 }
@@ -349,7 +349,7 @@
 		dev_uc_del(real_dev, dev->dev_addr);
 
 out:
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 	return 0;
 }
 
@@ -365,7 +365,7 @@
 
 	switch (cmd) {
 	case SIOCSHWTSTAMP:
-		if (!net_eq(dev_net(dev), &init_net))
+		if (!net_eq(dev_net(dev), dev_net(real_dev)))
 			break;
 		fallthrough;
 	case SIOCGMIIPHY:
@@ -586,7 +586,7 @@
 	dev->dev_id = real_dev->dev_id;
 
 	if (is_zero_ether_addr(dev->dev_addr)) {
-		ether_addr_copy(dev->dev_addr, real_dev->dev_addr);
+		eth_hw_addr_set(dev, real_dev->dev_addr);
 		dev->addr_assign_type = NET_ADDR_STOLEN;
 	}
 	if (is_zero_ether_addr(dev->broadcast))
@@ -615,11 +615,14 @@
 	if (!vlan->vlan_pcpu_stats)
 		return -ENOMEM;
 
+	/* Get vlan's reference to real_dev */
+	dev_hold(real_dev);
+
 	return 0;
 }
 
 /* Note: this function might be called multiple times for the same device. */
-void vlan_dev_uninit(struct net_device *dev)
+void vlan_dev_free_egress_priority(const struct net_device *dev)
 {
 	struct vlan_priority_tci_mapping *pm;
 	struct vlan_dev_priv *vlan = vlan_dev_priv(dev);
@@ -633,6 +636,16 @@
 	}
 }
 
+static void vlan_dev_uninit(struct net_device *dev)
+{
+	struct vlan_dev_priv *vlan = vlan_dev_priv(dev);
+
+	vlan_dev_free_egress_priority(dev);
+
+	/* Get rid of the vlan's reference to real_dev */
+	dev_put(vlan->real_dev);
+}
+
 static netdev_features_t vlan_dev_fix_features(struct net_device *dev,
 	netdev_features_t features)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/net/8021q/vlan_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/8021q/vlan_netlink.c
@@ -118,12 +118,16 @@
 	}
 	if (data[IFLA_VLAN_INGRESS_QOS]) {
 		nla_for_each_nested(attr, data[IFLA_VLAN_INGRESS_QOS], rem) {
+			if (nla_type(attr) != IFLA_VLAN_QOS_MAPPING)
+				continue;
 			m = nla_data(attr);
 			vlan_dev_set_ingress_priority(dev, m->to, m->from);
 		}
 	}
 	if (data[IFLA_VLAN_EGRESS_QOS]) {
 		nla_for_each_nested(attr, data[IFLA_VLAN_EGRESS_QOS], rem) {
+			if (nla_type(attr) != IFLA_VLAN_QOS_MAPPING)
+				continue;
 			m = nla_data(attr);
 			err = vlan_dev_set_egress_priority(dev, m->from, m->to);
 			if (err)
@@ -182,11 +186,16 @@
 	else if (dev->mtu > max_mtu)
 		return -EINVAL;
 
+	/* Note: If this initial vlan_changelink() fails, we need
+	 * to call vlan_dev_free_egress_priority() to free memory.
+	 */
 	err = vlan_changelink(dev, tb, data, extack);
+
 	if (!err)
 		err = register_vlan_dev(dev, extack);
+
 	if (err)
-		vlan_dev_uninit(dev);
+		vlan_dev_free_egress_priority(dev);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/client.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/client.c
@@ -32,10 +32,9 @@
 
 #define DEFAULT_MSIZE (128 * 1024)
 
-/*
-  * Client Option Parsing (code inspired by NFS code)
-  *  - a little lazy - parse all client options
-  */
+/* Client Option Parsing (code inspired by NFS code)
+ *  - a little lazy - parse all client options
+ */
 
 enum {
 	Opt_msize,
@@ -89,20 +88,18 @@
 }
 EXPORT_SYMBOL(p9_show_client_options);
 
-/*
- * Some error codes are taken directly from the server replies,
+/* Some error codes are taken directly from the server replies,
  * make sure they are valid.
  */
 static int safe_errno(int err)
 {
-	if ((err > 0) || (err < -MAX_ERRNO)) {
+	if (err > 0 || err < -MAX_ERRNO) {
 		p9_debug(P9_DEBUG_ERROR, "Invalid error code %d\n", err);
 		return -EPROTO;
 	}
 	return err;
 }
 
-
 /* Interpret mount option for protocol version */
 static int get_protocol_version(char *s)
 {
@@ -117,8 +114,9 @@
 	} else if (!strcmp(s, "9p2000.L")) {
 		version = p9_proto_2000L;
 		p9_debug(P9_DEBUG_9P, "Protocol version: 9P2000.L\n");
-	} else
+	} else {
 		pr_info("Unknown protocol version %s\n", s);
+	}
 
 	return version;
 }
@@ -147,15 +145,13 @@
 		return 0;
 
 	tmp_options = kstrdup(opts, GFP_KERNEL);
-	if (!tmp_options) {
-		p9_debug(P9_DEBUG_ERROR,
-			 "failed to allocate copy of option string\n");
+	if (!tmp_options)
 		return -ENOMEM;
-	}
 	options = tmp_options;
 
 	while ((p = strsep(&options, ",")) != NULL) {
 		int token, r;
+
 		if (!*p)
 			continue;
 		token = match_token(p, tokens, args);
@@ -187,7 +183,7 @@
 
 			v9fs_put_trans(clnt->trans_mod);
 			clnt->trans_mod = v9fs_get_trans_by_name(s);
-			if (clnt->trans_mod == NULL) {
+			if (!clnt->trans_mod) {
 				pr_info("Could not find request transport: %s\n",
 					s);
 				ret = -EINVAL;
@@ -237,6 +233,8 @@
 	if (!fc->sdata)
 		return -ENOMEM;
 	fc->capacity = alloc_msize;
+	fc->id = 0;
+	fc->tag = P9_NOTAG;
 	return 0;
 }
 
@@ -285,6 +283,11 @@
 	p9pdu_reset(&req->rc);
 	req->t_err = 0;
 	req->status = REQ_STATUS_ALLOC;
+	/* refcount needs to be set to 0 before inserting into the idr
+	 * so p9_tag_lookup does not accept a request that is not fully
+	 * initialized. refcount_set to 2 below will mark request ready.
+	 */
+	refcount_set(&req->refcount, 0);
 	init_waitqueue_head(&req->wq);
 	INIT_LIST_HEAD(&req->req_list);
 
@@ -311,7 +314,7 @@
 	 * callback), so p9_client_cb eats the second ref there
 	 * as the pointer is duplicated directly by virtqueue_add_sgs()
 	 */
-	refcount_set(&req->refcount.refcount, 2);
+	refcount_set(&req->refcount, 2);
 
 	return req;
 
@@ -347,7 +350,7 @@
 		if (!p9_req_try_get(req))
 			goto again;
 		if (req->tc.tag != tag) {
-			p9_req_put(req);
+			p9_req_put(c, req);
 			goto again;
 		}
 	}
@@ -373,20 +376,18 @@
 	spin_lock_irqsave(&c->lock, flags);
 	idr_remove(&c->reqs, tag);
 	spin_unlock_irqrestore(&c->lock, flags);
-	return p9_req_put(r);
-}
-
-static void p9_req_free(struct kref *ref)
-{
-	struct p9_req_t *r = container_of(ref, struct p9_req_t, refcount);
-	p9_fcall_fini(&r->tc);
-	p9_fcall_fini(&r->rc);
-	kmem_cache_free(p9_req_cache, r);
+	return p9_req_put(c, r);
 }
 
-int p9_req_put(struct p9_req_t *r)
+int p9_req_put(struct p9_client *c, struct p9_req_t *r)
 {
-	return kref_put(&r->refcount, p9_req_free);
+	if (refcount_dec_and_test(&r->refcount)) {
+		p9_fcall_fini(&r->tc);
+		p9_fcall_fini(&r->rc);
+		kmem_cache_free(p9_req_cache, r);
+		return 1;
+	}
+	return 0;
 }
 EXPORT_SYMBOL(p9_req_put);
 
@@ -423,8 +424,7 @@
 {
 	p9_debug(P9_DEBUG_MUX, " tag %d\n", req->tc.tag);
 
-	/*
-	 * This barrier is needed to make sure any change made to req before
+	/* This barrier is needed to make sure any change made to req before
 	 * the status change is visible to another thread
 	 */
 	smp_wmb();
@@ -432,7 +432,7 @@
 
 	wake_up(&req->wq);
 	p9_debug(P9_DEBUG_MUX, "wakeup: %d\n", req->tc.tag);
-	p9_req_put(req);
+	p9_req_put(c, req);
 }
 EXPORT_SYMBOL(p9_client_cb);
 
@@ -446,12 +446,12 @@
  */
 
 int
-p9_parse_header(struct p9_fcall *pdu, int32_t *size, int8_t *type, int16_t *tag,
-								int rewind)
+p9_parse_header(struct p9_fcall *pdu, int32_t *size, int8_t *type,
+		int16_t *tag, int rewind)
 {
-	int8_t r_type;
-	int16_t r_tag;
-	int32_t r_size;
+	s8 r_type;
+	s16 r_tag;
+	s32 r_size;
 	int offset = pdu->offset;
 	int err;
 
@@ -499,7 +499,7 @@
 
 static int p9_check_errors(struct p9_client *c, struct p9_req_t *req)
 {
-	int8_t type;
+	s8 type;
 	int err;
 	int ecode;
 
@@ -510,8 +510,7 @@
 			 req->rc.size);
 		return -EIO;
 	}
-	/*
-	 * dump the response from server
+	/* dump the response from server
 	 * This should be after check errors which poplulate pdu_fcall.
 	 */
 	trace_9p_protocol_dump(c, &req->rc);
@@ -523,11 +522,14 @@
 		return 0;
 
 	if (!p9_is_proto_dotl(c)) {
-		char *ename;
+		char *ename = NULL;
+
 		err = p9pdu_readf(&req->rc, c->proto_version, "s?d",
 				  &ename, &ecode);
-		if (err)
+		if (err) {
+			kfree(ename);
 			goto out_err;
+		}
 
 		if (p9_is_proto_dotu(c) && ecode < 512)
 			err = -ecode;
@@ -541,6 +543,8 @@
 		kfree(ename);
 	} else {
 		err = p9pdu_readf(&req->rc, c->proto_version, "d", &ecode);
+		if (err)
+			goto out_err;
 		err = -ecode;
 
 		p9_debug(P9_DEBUG_9P, "<<< RLERROR (%d)\n", -ecode);
@@ -572,12 +576,11 @@
 {
 	int err;
 	int ecode;
-	int8_t type;
+	s8 type;
 	char *ename = NULL;
 
 	err = p9_parse_header(&req->rc, NULL, &type, NULL, 0);
-	/*
-	 * dump the response from server
+	/* dump the response from server
 	 * This should be after parse_header which poplulate pdu_fcall.
 	 */
 	trace_9p_protocol_dump(c, &req->rc);
@@ -605,7 +608,7 @@
 		if (len > inline_len) {
 			/* We have error in external buffer */
 			if (!copy_from_iter_full(ename + inline_len,
-					     len - inline_len, uidata)) {
+						 len - inline_len, uidata)) {
 				err = -EFAULT;
 				goto out_err;
 			}
@@ -657,7 +660,7 @@
 static int p9_client_flush(struct p9_client *c, struct p9_req_t *oldreq)
 {
 	struct p9_req_t *req;
-	int16_t oldtag;
+	s16 oldtag;
 	int err;
 
 	err = p9_parse_header(&oldreq->tc, NULL, NULL, &oldtag, 1);
@@ -670,8 +673,7 @@
 	if (IS_ERR(req))
 		return PTR_ERR(req);
 
-	/*
-	 * if we haven't received a response for oldreq,
+	/* if we haven't received a response for oldreq,
 	 * remove it from the list
 	 */
 	if (oldreq->status == REQ_STATUS_SENT) {
@@ -697,7 +699,7 @@
 		return ERR_PTR(-EIO);
 
 	/* if status is begin_disconnected we allow only clunk request */
-	if ((c->status == BeginDisconnect) && (type != P9_TCLUNK))
+	if (c->status == BeginDisconnect && type != P9_TCLUNK)
 		return ERR_PTR(-EIO);
 
 	req = p9_tag_alloc(c, type, req_size);
@@ -715,7 +717,7 @@
 reterr:
 	p9_tag_remove(c, req);
 	/* We have to put also the 2nd reference as it won't be used */
-	p9_req_put(req);
+	p9_req_put(c, req);
 	return ERR_PTR(err);
 }
 
@@ -745,13 +747,14 @@
 	if (signal_pending(current)) {
 		sigpending = 1;
 		clear_thread_flag(TIF_SIGPENDING);
-	} else
+	} else {
 		sigpending = 0;
+	}
 
 	err = c->trans_mod->request(c, req);
 	if (err < 0) {
 		/* write won't happen */
-		p9_req_put(req);
+		p9_req_put(c, req);
 		if (err != -ERESTARTSYS && err != -EFAULT)
 			c->status = Disconnected;
 		goto recalc_sigpending;
@@ -760,14 +763,13 @@
 	/* Wait for the response */
 	err = wait_event_killable(req->wq, req->status >= REQ_STATUS_RCVD);
 
-	/*
-	 * Make sure our req is coherent with regard to updates in other
+	/* Make sure our req is coherent with regard to updates in other
 	 * threads - echoes to wmb() in the callback
 	 */
 	smp_rmb();
 
-	if ((err == -ERESTARTSYS) && (c->status == Connected)
-				  && (type == P9_TFLUSH)) {
+	if (err == -ERESTARTSYS && c->status == Connected &&
+	    type == P9_TFLUSH) {
 		sigpending = 1;
 		clear_thread_flag(TIF_SIGPENDING);
 		goto again;
@@ -777,7 +779,7 @@
 		p9_debug(P9_DEBUG_ERROR, "req_status error %d\n", req->t_err);
 		err = req->t_err;
 	}
-	if ((err == -ERESTARTSYS) && (c->status == Connected)) {
+	if (err == -ERESTARTSYS && c->status == Connected) {
 		p9_debug(P9_DEBUG_MUX, "flushing\n");
 		sigpending = 1;
 		clear_thread_flag(TIF_SIGPENDING);
@@ -832,8 +834,7 @@
 	struct p9_req_t *req;
 
 	va_start(ap, fmt);
-	/*
-	 * We allocate a inline protocol data of only 4k bytes.
+	/* We allocate a inline protocol data of only 4k bytes.
 	 * The actual content is passed in zero-copy fashion.
 	 */
 	req = p9_client_prepare_req(c, type, P9_ZC_HDR_SZ, fmt, ap);
@@ -844,8 +845,9 @@
 	if (signal_pending(current)) {
 		sigpending = 1;
 		clear_thread_flag(TIF_SIGPENDING);
-	} else
+	} else {
 		sigpending = 0;
+	}
 
 	err = c->trans_mod->zc_request(c, req, uidata, uodata,
 				       inlen, olen, in_hdrlen);
@@ -859,7 +861,7 @@
 		p9_debug(P9_DEBUG_ERROR, "req_status error %d\n", req->t_err);
 		err = req->t_err;
 	}
-	if ((err == -ERESTARTSYS) && (c->status == Connected)) {
+	if (err == -ERESTARTSYS && c->status == Connected) {
 		p9_debug(P9_DEBUG_MUX, "flushing\n");
 		sigpending = 1;
 		clear_thread_flag(TIF_SIGPENDING);
@@ -895,16 +897,13 @@
 	struct p9_fid *fid;
 
 	p9_debug(P9_DEBUG_FID, "clnt %p\n", clnt);
-	fid = kmalloc(sizeof(struct p9_fid), GFP_KERNEL);
+	fid = kzalloc(sizeof(*fid), GFP_KERNEL);
 	if (!fid)
 		return NULL;
 
-	memset(&fid->qid, 0, sizeof(struct p9_qid));
 	fid->mode = -1;
 	fid->uid = current_fsuid();
 	fid->clnt = clnt;
-	fid->rdir = NULL;
-	fid->fid = 0;
 	refcount_set(&fid->count, 1);
 
 	idr_preload(GFP_KERNEL);
@@ -947,15 +946,15 @@
 	switch (c->proto_version) {
 	case p9_proto_2000L:
 		req = p9_client_rpc(c, P9_TVERSION, "ds",
-					c->msize, "9P2000.L");
+				    c->msize, "9P2000.L");
 		break;
 	case p9_proto_2000u:
 		req = p9_client_rpc(c, P9_TVERSION, "ds",
-					c->msize, "9P2000.u");
+				    c->msize, "9P2000.u");
 		break;
 	case p9_proto_legacy:
 		req = p9_client_rpc(c, P9_TVERSION, "ds",
-					c->msize, "9P2000");
+				    c->msize, "9P2000");
 		break;
 	default:
 		return -EINVAL;
@@ -972,13 +971,13 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< RVERSION msize %d %s\n", msize, version);
-	if (!strncmp(version, "9P2000.L", 8))
+	if (!strncmp(version, "9P2000.L", 8)) {
 		c->proto_version = p9_proto_2000L;
-	else if (!strncmp(version, "9P2000.u", 8))
+	} else if (!strncmp(version, "9P2000.u", 8)) {
 		c->proto_version = p9_proto_2000u;
-	else if (!strncmp(version, "9P2000", 6))
+	} else if (!strncmp(version, "9P2000", 6)) {
 		c->proto_version = p9_proto_legacy;
-	else {
+	} else {
 		p9_debug(P9_DEBUG_ERROR,
 			 "server returned an unknown version: %s\n", version);
 		err = -EREMOTEIO;
@@ -1004,11 +1003,13 @@
 struct p9_client *p9_client_create(const char *dev_name, char *options)
 {
 	int err;
+	static atomic_t seqno = ATOMIC_INIT(0);
 	struct p9_client *clnt;
 	char *client_id;
+	char *cache_name;
 
 	err = 0;
-	clnt = kmalloc(sizeof(struct p9_client), GFP_KERNEL);
+	clnt = kmalloc(sizeof(*clnt), GFP_KERNEL);
 	if (!clnt)
 		return ERR_PTR(-ENOMEM);
 
@@ -1030,7 +1031,7 @@
 	if (!clnt->trans_mod)
 		clnt->trans_mod = v9fs_get_default_trans();
 
-	if (clnt->trans_mod == NULL) {
+	if (!clnt->trans_mod) {
 		err = -EPROTONOSUPPORT;
 		p9_debug(P9_DEBUG_ERROR,
 			 "No transport defined or default transport\n");
@@ -1058,15 +1059,23 @@
 	if (err)
 		goto close_trans;
 
+	cache_name = kasprintf(GFP_KERNEL,
+		"9p-fcall-cache-%u", atomic_inc_return(&seqno));
+	if (!cache_name) {
+		err = -ENOMEM;
+		goto close_trans;
+	}
+
 	/* P9_HDRSZ + 4 is the smallest packet header we can have that is
 	 * followed by data accessed from userspace by read
 	 */
 	clnt->fcall_cache =
-		kmem_cache_create_usercopy("9p-fcall-cache", clnt->msize,
+		kmem_cache_create_usercopy(cache_name, clnt->msize,
 					   0, 0, P9_HDRSZ + 4,
 					   clnt->msize - (P9_HDRSZ + 4),
 					   NULL);
 
+	kfree(cache_name);
 	return clnt;
 
 close_trans:
@@ -1118,14 +1127,14 @@
 EXPORT_SYMBOL(p9_client_begin_disconnect);
 
 struct p9_fid *p9_client_attach(struct p9_client *clnt, struct p9_fid *afid,
-	const char *uname, kuid_t n_uname, const char *aname)
+				const char *uname, kuid_t n_uname,
+				const char *aname)
 {
 	int err = 0;
 	struct p9_req_t *req;
 	struct p9_fid *fid;
 	struct p9_qid qid;
 
-
 	p9_debug(P9_DEBUG_9P, ">>> TATTACH afid %d uname %s aname %s\n",
 		 afid ? afid->fid : -1, uname, aname);
 	fid = p9_fid_create(clnt);
@@ -1136,7 +1145,7 @@
 	fid->uid = n_uname;
 
 	req = p9_client_rpc(clnt, P9_TATTACH, "ddss?u", fid->fid,
-			afid ? afid->fid : P9_NOFID, uname, aname, n_uname);
+			    afid ? afid->fid : P9_NOFID, uname, aname, n_uname);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1150,7 +1159,7 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< RATTACH qid %x.%llx.%x\n",
-		 qid.type, (unsigned long long)qid.path, qid.version);
+		 qid.type, qid.path, qid.version);
 
 	memmove(&fid->qid, &qid, sizeof(struct p9_qid));
 
@@ -1165,14 +1174,14 @@
 EXPORT_SYMBOL(p9_client_attach);
 
 struct p9_fid *p9_client_walk(struct p9_fid *oldfid, uint16_t nwname,
-		const unsigned char * const *wnames, int clone)
+			      const unsigned char * const *wnames, int clone)
 {
 	int err;
 	struct p9_client *clnt;
 	struct p9_fid *fid;
 	struct p9_qid *wqids;
 	struct p9_req_t *req;
-	uint16_t nwqids, count;
+	u16 nwqids, count;
 
 	err = 0;
 	wqids = NULL;
@@ -1185,14 +1194,14 @@
 		}
 
 		fid->uid = oldfid->uid;
-	} else
+	} else {
 		fid = oldfid;
-
+	}
 
 	p9_debug(P9_DEBUG_9P, ">>> TWALK fids %d,%d nwname %ud wname[0] %s\n",
 		 oldfid->fid, fid->fid, nwname, wnames ? wnames[0] : NULL);
 	req = p9_client_rpc(clnt, P9_TWALK, "ddT", oldfid->fid, fid->fid,
-								nwname, wnames);
+			    nwname, wnames);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1215,9 +1224,9 @@
 
 	for (count = 0; count < nwqids; count++)
 		p9_debug(P9_DEBUG_9P, "<<<     [%d] %x.%llx.%x\n",
-			count, wqids[count].type,
-			(unsigned long long)wqids[count].path,
-			wqids[count].version);
+			 count, wqids[count].type,
+			 wqids[count].path,
+			 wqids[count].version);
 
 	if (nwname)
 		memmove(&fid->qid, &wqids[nwqids - 1], sizeof(struct p9_qid));
@@ -1233,7 +1242,7 @@
 	fid = NULL;
 
 error:
-	if (fid && (fid != oldfid))
+	if (fid && fid != oldfid)
 		p9_fid_destroy(fid);
 
 	return ERR_PTR(err);
@@ -1250,7 +1259,7 @@
 
 	clnt = fid->clnt;
 	p9_debug(P9_DEBUG_9P, ">>> %s fid %d mode %d\n",
-		p9_is_proto_dotl(clnt) ? "TLOPEN" : "TOPEN", fid->fid, mode);
+		 p9_is_proto_dotl(clnt) ? "TLOPEN" : "TOPEN", fid->fid, mode);
 	err = 0;
 
 	if (fid->mode != -1)
@@ -1272,8 +1281,8 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< %s qid %x.%llx.%x iounit %x\n",
-		p9_is_proto_dotl(clnt) ? "RLOPEN" : "ROPEN",  qid.type,
-		(unsigned long long)qid.path, qid.version, iounit);
+		 p9_is_proto_dotl(clnt) ? "RLOPEN" : "ROPEN",  qid.type,
+		 qid.path, qid.version, iounit);
 
 	memmove(&fid->qid, &qid, sizeof(struct p9_qid));
 	fid->mode = mode;
@@ -1286,8 +1295,8 @@
 }
 EXPORT_SYMBOL(p9_client_open);
 
-int p9_client_create_dotl(struct p9_fid *ofid, const char *name, u32 flags, u32 mode,
-		kgid_t gid, struct p9_qid *qid)
+int p9_client_create_dotl(struct p9_fid *ofid, const char *name, u32 flags,
+			  u32 mode, kgid_t gid, struct p9_qid *qid)
 {
 	int err = 0;
 	struct p9_client *clnt;
@@ -1295,16 +1304,16 @@
 	int iounit;
 
 	p9_debug(P9_DEBUG_9P,
-			">>> TLCREATE fid %d name %s flags %d mode %d gid %d\n",
-			ofid->fid, name, flags, mode,
-		 	from_kgid(&init_user_ns, gid));
+		 ">>> TLCREATE fid %d name %s flags %d mode %d gid %d\n",
+		 ofid->fid, name, flags, mode,
+		 from_kgid(&init_user_ns, gid));
 	clnt = ofid->clnt;
 
 	if (ofid->mode != -1)
 		return -EINVAL;
 
 	req = p9_client_rpc(clnt, P9_TLCREATE, "dsddg", ofid->fid, name, flags,
-			mode, gid);
+			    mode, gid);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1317,12 +1326,10 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< RLCREATE qid %x.%llx.%x iounit %x\n",
-			qid->type,
-			(unsigned long long)qid->path,
-			qid->version, iounit);
+		 qid->type, qid->path, qid->version, iounit);
 
 	memmove(&ofid->qid, qid, sizeof(struct p9_qid));
-	ofid->mode = mode;
+	ofid->mode = flags;
 	ofid->iounit = iounit;
 
 free_and_error:
@@ -1342,7 +1349,7 @@
 	int iounit;
 
 	p9_debug(P9_DEBUG_9P, ">>> TCREATE fid %d name %s perm %d mode %d\n",
-						fid->fid, name, perm, mode);
+		 fid->fid, name, perm, mode);
 	err = 0;
 	clnt = fid->clnt;
 
@@ -1350,7 +1357,7 @@
 		return -EINVAL;
 
 	req = p9_client_rpc(clnt, P9_TCREATE, "dsdb?s", fid->fid, name, perm,
-				mode, extension);
+			    mode, extension);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1363,9 +1370,7 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< RCREATE qid %x.%llx.%x iounit %x\n",
-				qid.type,
-				(unsigned long long)qid.path,
-				qid.version, iounit);
+		 qid.type, qid.path, qid.version, iounit);
 
 	memmove(&fid->qid, &qid, sizeof(struct p9_qid));
 	fid->mode = mode;
@@ -1379,18 +1384,18 @@
 EXPORT_SYMBOL(p9_client_fcreate);
 
 int p9_client_symlink(struct p9_fid *dfid, const char *name,
-		const char *symtgt, kgid_t gid, struct p9_qid *qid)
+		      const char *symtgt, kgid_t gid, struct p9_qid *qid)
 {
 	int err = 0;
 	struct p9_client *clnt;
 	struct p9_req_t *req;
 
 	p9_debug(P9_DEBUG_9P, ">>> TSYMLINK dfid %d name %s  symtgt %s\n",
-			dfid->fid, name, symtgt);
+		 dfid->fid, name, symtgt);
 	clnt = dfid->clnt;
 
 	req = p9_client_rpc(clnt, P9_TSYMLINK, "dssg", dfid->fid, name, symtgt,
-			gid);
+			    gid);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1403,7 +1408,7 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< RSYMLINK qid %x.%llx.%x\n",
-			qid->type, (unsigned long long)qid->path, qid->version);
+		 qid->type, qid->path, qid->version);
 
 free_and_error:
 	p9_tag_remove(clnt, req);
@@ -1418,10 +1423,10 @@
 	struct p9_req_t *req;
 
 	p9_debug(P9_DEBUG_9P, ">>> TLINK dfid %d oldfid %d newname %s\n",
-			dfid->fid, oldfid->fid, newname);
+		 dfid->fid, oldfid->fid, newname);
 	clnt = dfid->clnt;
 	req = p9_client_rpc(clnt, P9_TLINK, "dds", dfid->fid, oldfid->fid,
-			newname);
+			    newname);
 	if (IS_ERR(req))
 		return PTR_ERR(req);
 
@@ -1438,7 +1443,7 @@
 	struct p9_req_t *req;
 
 	p9_debug(P9_DEBUG_9P, ">>> TFSYNC fid %d datasync:%d\n",
-			fid->fid, datasync);
+		 fid->fid, datasync);
 	err = 0;
 	clnt = fid->clnt;
 
@@ -1474,8 +1479,8 @@
 		return 0;
 
 again:
-	p9_debug(P9_DEBUG_9P, ">>> TCLUNK fid %d (try %d)\n", fid->fid,
-								retries);
+	p9_debug(P9_DEBUG_9P, ">>> TCLUNK fid %d (try %d)\n",
+		 fid->fid, retries);
 	err = 0;
 	clnt = fid->clnt;
 
@@ -1489,16 +1494,16 @@
 
 	p9_tag_remove(clnt, req);
 error:
-	/*
-	 * Fid is not valid even after a failed clunk
+	/* Fid is not valid even after a failed clunk
 	 * If interrupted, retry once then give up and
 	 * leak fid until umount.
 	 */
 	if (err == -ERESTARTSYS) {
 		if (retries++ == 0)
 			goto again;
-	} else
+	} else {
 		p9_fid_destroy(fid);
+	}
 	return err;
 }
 EXPORT_SYMBOL(p9_client_clunk);
@@ -1538,7 +1543,7 @@
 	struct p9_client *clnt;
 
 	p9_debug(P9_DEBUG_9P, ">>> TUNLINKAT fid %d %s %d\n",
-		   dfid->fid, name, flags);
+		 dfid->fid, name, flags);
 
 	clnt = dfid->clnt;
 	req = p9_client_rpc(clnt, P9_TUNLINKAT, "dsd", dfid->fid, name, flags);
@@ -1584,8 +1589,8 @@
 	char *dataptr;
 
 	*err = 0;
-	p9_debug(P9_DEBUG_9P, ">>> TREAD fid %d offset %llu %d\n",
-		   fid->fid, (unsigned long long) offset, (int)iov_iter_count(to));
+	p9_debug(P9_DEBUG_9P, ">>> TREAD fid %d offset %llu %zu\n",
+		 fid->fid, offset, iov_iter_count(to));
 
 	rsize = fid->iounit;
 	if (!rsize || rsize > clnt->msize - P9_IOHDRSZ)
@@ -1651,13 +1656,13 @@
 	*err = 0;
 
 	p9_debug(P9_DEBUG_9P, ">>> TWRITE fid %d offset %llu count %zd\n",
-				fid->fid, (unsigned long long) offset,
-				iov_iter_count(from));
+		 fid->fid, offset, iov_iter_count(from));
 
 	while (iov_iter_count(from)) {
 		int count = iov_iter_count(from);
 		int rsize = fid->iounit;
-		if (!rsize || rsize > clnt->msize-P9_IOHDRSZ)
+
+		if (!rsize || rsize > clnt->msize - P9_IOHDRSZ)
 			rsize = clnt->msize - P9_IOHDRSZ;
 
 		if (count < rsize)
@@ -1670,7 +1675,7 @@
 					       fid->fid, offset, rsize);
 		} else {
 			req = p9_client_rpc(clnt, P9_TWRITE, "dqV", fid->fid,
-						    offset, rsize, from);
+					    offset, rsize, from);
 		}
 		if (IS_ERR(req)) {
 			*err = PTR_ERR(req);
@@ -1703,12 +1708,13 @@
 {
 	int err;
 	struct p9_client *clnt;
-	struct p9_wstat *ret = kmalloc(sizeof(struct p9_wstat), GFP_KERNEL);
+	struct p9_wstat *ret;
 	struct p9_req_t *req;
 	u16 ignored;
 
 	p9_debug(P9_DEBUG_9P, ">>> TSTAT fid %d\n", fid->fid);
 
+	ret = kmalloc(sizeof(*ret), GFP_KERNEL);
 	if (!ret)
 		return ERR_PTR(-ENOMEM);
 
@@ -1729,17 +1735,17 @@
 	}
 
 	p9_debug(P9_DEBUG_9P,
-		"<<< RSTAT sz=%x type=%x dev=%x qid=%x.%llx.%x\n"
-		"<<<    mode=%8.8x atime=%8.8x mtime=%8.8x length=%llx\n"
-		"<<<    name=%s uid=%s gid=%s muid=%s extension=(%s)\n"
-		"<<<    uid=%d gid=%d n_muid=%d\n",
-		ret->size, ret->type, ret->dev, ret->qid.type,
-		(unsigned long long)ret->qid.path, ret->qid.version, ret->mode,
-		ret->atime, ret->mtime, (unsigned long long)ret->length,
-		ret->name, ret->uid, ret->gid, ret->muid, ret->extension,
-		from_kuid(&init_user_ns, ret->n_uid),
-		from_kgid(&init_user_ns, ret->n_gid),
-		from_kuid(&init_user_ns, ret->n_muid));
+		 "<<< RSTAT sz=%x type=%x dev=%x qid=%x.%llx.%x\n"
+		 "<<<    mode=%8.8x atime=%8.8x mtime=%8.8x length=%llx\n"
+		 "<<<    name=%s uid=%s gid=%s muid=%s extension=(%s)\n"
+		 "<<<    uid=%d gid=%d n_muid=%d\n",
+		 ret->size, ret->type, ret->dev, ret->qid.type, ret->qid.path,
+		 ret->qid.version, ret->mode,
+		 ret->atime, ret->mtime, ret->length,
+		 ret->name, ret->uid, ret->gid, ret->muid, ret->extension,
+		 from_kuid(&init_user_ns, ret->n_uid),
+		 from_kgid(&init_user_ns, ret->n_gid),
+		 from_kuid(&init_user_ns, ret->n_muid));
 
 	p9_tag_remove(clnt, req);
 	return ret;
@@ -1751,17 +1757,17 @@
 EXPORT_SYMBOL(p9_client_stat);
 
 struct p9_stat_dotl *p9_client_getattr_dotl(struct p9_fid *fid,
-							u64 request_mask)
+					    u64 request_mask)
 {
 	int err;
 	struct p9_client *clnt;
-	struct p9_stat_dotl *ret = kmalloc(sizeof(struct p9_stat_dotl),
-								GFP_KERNEL);
+	struct p9_stat_dotl *ret;
 	struct p9_req_t *req;
 
 	p9_debug(P9_DEBUG_9P, ">>> TGETATTR fid %d, request_mask %lld\n",
-							fid->fid, request_mask);
+		 fid->fid, request_mask);
 
+	ret = kmalloc(sizeof(*ret), GFP_KERNEL);
 	if (!ret)
 		return ERR_PTR(-ENOMEM);
 
@@ -1781,26 +1787,27 @@
 		goto error;
 	}
 
-	p9_debug(P9_DEBUG_9P,
-		"<<< RGETATTR st_result_mask=%lld\n"
-		"<<< qid=%x.%llx.%x\n"
-		"<<< st_mode=%8.8x st_nlink=%llu\n"
-		"<<< st_uid=%d st_gid=%d\n"
-		"<<< st_rdev=%llx st_size=%llx st_blksize=%llu st_blocks=%llu\n"
-		"<<< st_atime_sec=%lld st_atime_nsec=%lld\n"
-		"<<< st_mtime_sec=%lld st_mtime_nsec=%lld\n"
-		"<<< st_ctime_sec=%lld st_ctime_nsec=%lld\n"
-		"<<< st_btime_sec=%lld st_btime_nsec=%lld\n"
-		"<<< st_gen=%lld st_data_version=%lld\n",
-		ret->st_result_mask, ret->qid.type, ret->qid.path,
-		ret->qid.version, ret->st_mode, ret->st_nlink,
-		from_kuid(&init_user_ns, ret->st_uid),
-		from_kgid(&init_user_ns, ret->st_gid),
-		ret->st_rdev, ret->st_size, ret->st_blksize,
-		ret->st_blocks, ret->st_atime_sec, ret->st_atime_nsec,
-		ret->st_mtime_sec, ret->st_mtime_nsec, ret->st_ctime_sec,
-		ret->st_ctime_nsec, ret->st_btime_sec, ret->st_btime_nsec,
-		ret->st_gen, ret->st_data_version);
+	p9_debug(P9_DEBUG_9P, "<<< RGETATTR st_result_mask=%lld\n"
+		 "<<< qid=%x.%llx.%x\n"
+		 "<<< st_mode=%8.8x st_nlink=%llu\n"
+		 "<<< st_uid=%d st_gid=%d\n"
+		 "<<< st_rdev=%llx st_size=%llx st_blksize=%llu st_blocks=%llu\n"
+		 "<<< st_atime_sec=%lld st_atime_nsec=%lld\n"
+		 "<<< st_mtime_sec=%lld st_mtime_nsec=%lld\n"
+		 "<<< st_ctime_sec=%lld st_ctime_nsec=%lld\n"
+		 "<<< st_btime_sec=%lld st_btime_nsec=%lld\n"
+		 "<<< st_gen=%lld st_data_version=%lld\n",
+		 ret->st_result_mask,
+		 ret->qid.type, ret->qid.path, ret->qid.version,
+		 ret->st_mode, ret->st_nlink,
+		 from_kuid(&init_user_ns, ret->st_uid),
+		 from_kgid(&init_user_ns, ret->st_gid),
+		 ret->st_rdev, ret->st_size, ret->st_blksize, ret->st_blocks,
+		 ret->st_atime_sec, ret->st_atime_nsec,
+		 ret->st_mtime_sec, ret->st_mtime_nsec,
+		 ret->st_ctime_sec, ret->st_ctime_nsec,
+		 ret->st_btime_sec, ret->st_btime_nsec,
+		 ret->st_gen, ret->st_data_version);
 
 	p9_tag_remove(clnt, req);
 	return ret;
@@ -1819,7 +1826,7 @@
 	/* size[2] type[2] dev[4] qid[13] */
 	/* mode[4] atime[4] mtime[4] length[8]*/
 	/* name[s] uid[s] gid[s] muid[s] */
-	ret = 2+4+13+4+4+4+8+2+2+2+2;
+	ret = 2 + 4 + 13 + 4 + 4 + 4 + 8 + 2 + 2 + 2 + 2;
 
 	if (wst->name)
 		ret += strlen(wst->name);
@@ -1830,9 +1837,10 @@
 	if (wst->muid)
 		ret += strlen(wst->muid);
 
-	if ((proto_version == p9_proto_2000u) ||
-		(proto_version == p9_proto_2000L)) {
-		ret += 2+4+4+4;	/* extension[s] n_uid[4] n_gid[4] n_muid[4] */
+	if (proto_version == p9_proto_2000u ||
+	    proto_version == p9_proto_2000L) {
+		/* extension[s] n_uid[4] n_gid[4] n_muid[4] */
+		ret += 2 + 4 + 4 + 4;
 		if (wst->extension)
 			ret += strlen(wst->extension);
 	}
@@ -1849,21 +1857,23 @@
 	err = 0;
 	clnt = fid->clnt;
 	wst->size = p9_client_statsize(wst, clnt->proto_version);
-	p9_debug(P9_DEBUG_9P, ">>> TWSTAT fid %d\n", fid->fid);
+	p9_debug(P9_DEBUG_9P, ">>> TWSTAT fid %d\n",
+		 fid->fid);
 	p9_debug(P9_DEBUG_9P,
-		"     sz=%x type=%x dev=%x qid=%x.%llx.%x\n"
-		"     mode=%8.8x atime=%8.8x mtime=%8.8x length=%llx\n"
-		"     name=%s uid=%s gid=%s muid=%s extension=(%s)\n"
-		"     uid=%d gid=%d n_muid=%d\n",
-		wst->size, wst->type, wst->dev, wst->qid.type,
-		(unsigned long long)wst->qid.path, wst->qid.version, wst->mode,
-		wst->atime, wst->mtime, (unsigned long long)wst->length,
-		wst->name, wst->uid, wst->gid, wst->muid, wst->extension,
-		from_kuid(&init_user_ns, wst->n_uid),
-		from_kgid(&init_user_ns, wst->n_gid),
-		from_kuid(&init_user_ns, wst->n_muid));
+		 "     sz=%x type=%x dev=%x qid=%x.%llx.%x\n"
+		 "     mode=%8.8x atime=%8.8x mtime=%8.8x length=%llx\n"
+		 "     name=%s uid=%s gid=%s muid=%s extension=(%s)\n"
+		 "     uid=%d gid=%d n_muid=%d\n",
+		 wst->size, wst->type, wst->dev, wst->qid.type,
+		 wst->qid.path, wst->qid.version,
+		 wst->mode, wst->atime, wst->mtime, wst->length,
+		 wst->name, wst->uid, wst->gid, wst->muid, wst->extension,
+		 from_kuid(&init_user_ns, wst->n_uid),
+		 from_kgid(&init_user_ns, wst->n_gid),
+		 from_kuid(&init_user_ns, wst->n_muid));
 
-	req = p9_client_rpc(clnt, P9_TWSTAT, "dwS", fid->fid, wst->size+2, wst);
+	req = p9_client_rpc(clnt, P9_TWSTAT, "dwS",
+			    fid->fid, wst->size + 2, wst);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1886,15 +1896,15 @@
 	err = 0;
 	clnt = fid->clnt;
 	p9_debug(P9_DEBUG_9P, ">>> TSETATTR fid %d\n", fid->fid);
-	p9_debug(P9_DEBUG_9P,
-		"    valid=%x mode=%x uid=%d gid=%d size=%lld\n"
-		"    atime_sec=%lld atime_nsec=%lld\n"
-		"    mtime_sec=%lld mtime_nsec=%lld\n",
-		p9attr->valid, p9attr->mode,
-		from_kuid(&init_user_ns, p9attr->uid),
-		from_kgid(&init_user_ns, p9attr->gid),
-		p9attr->size, p9attr->atime_sec, p9attr->atime_nsec,
-		p9attr->mtime_sec, p9attr->mtime_nsec);
+	p9_debug(P9_DEBUG_9P, "    valid=%x mode=%x uid=%d gid=%d size=%lld\n",
+		 p9attr->valid, p9attr->mode,
+		 from_kuid(&init_user_ns, p9attr->uid),
+		 from_kgid(&init_user_ns, p9attr->gid),
+		 p9attr->size);
+	p9_debug(P9_DEBUG_9P, "    atime_sec=%lld atime_nsec=%lld\n",
+		 p9attr->atime_sec, p9attr->atime_nsec);
+	p9_debug(P9_DEBUG_9P, "    mtime_sec=%lld mtime_nsec=%lld\n",
+		 p9attr->mtime_sec, p9attr->mtime_nsec);
 
 	req = p9_client_rpc(clnt, P9_TSETATTR, "dI", fid->fid, p9attr);
 
@@ -1935,12 +1945,10 @@
 		goto error;
 	}
 
-	p9_debug(P9_DEBUG_9P, "<<< RSTATFS fid %d type 0x%lx bsize %ld "
-		"blocks %llu bfree %llu bavail %llu files %llu ffree %llu "
-		"fsid %llu namelen %ld\n",
-		fid->fid, (long unsigned int)sb->type, (long int)sb->bsize,
-		sb->blocks, sb->bfree, sb->bavail, sb->files,  sb->ffree,
-		sb->fsid, (long int)sb->namelen);
+	p9_debug(P9_DEBUG_9P,
+		 "<<< RSTATFS fid %d type 0x%x bsize %u blocks %llu bfree %llu bavail %llu files %llu ffree %llu fsid %llu namelen %u\n",
+		 fid->fid, sb->type, sb->bsize, sb->blocks, sb->bfree,
+		 sb->bavail, sb->files, sb->ffree, sb->fsid, sb->namelen);
 
 	p9_tag_remove(clnt, req);
 error:
@@ -1959,10 +1967,10 @@
 	clnt = fid->clnt;
 
 	p9_debug(P9_DEBUG_9P, ">>> TRENAME fid %d newdirfid %d name %s\n",
-			fid->fid, newdirfid->fid, name);
+		 fid->fid, newdirfid->fid, name);
 
 	req = p9_client_rpc(clnt, P9_TRENAME, "dds", fid->fid,
-			newdirfid->fid, name);
+			    newdirfid->fid, name);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -1986,9 +1994,9 @@
 	err = 0;
 	clnt = olddirfid->clnt;
 
-	p9_debug(P9_DEBUG_9P, ">>> TRENAMEAT olddirfid %d old name %s"
-		   " newdirfid %d new name %s\n", olddirfid->fid, old_name,
-		   newdirfid->fid, new_name);
+	p9_debug(P9_DEBUG_9P,
+		 ">>> TRENAMEAT olddirfid %d old name %s newdirfid %d new name %s\n",
+		 olddirfid->fid, old_name, newdirfid->fid, new_name);
 
 	req = p9_client_rpc(clnt, P9_TRENAMEAT, "dsds", olddirfid->fid,
 			    old_name, newdirfid->fid, new_name);
@@ -1998,7 +2006,7 @@
 	}
 
 	p9_debug(P9_DEBUG_9P, "<<< RRENAMEAT newdirfid %d new name %s\n",
-		   newdirfid->fid, new_name);
+		 newdirfid->fid, new_name);
 
 	p9_tag_remove(clnt, req);
 error:
@@ -2006,11 +2014,10 @@
 }
 EXPORT_SYMBOL(p9_client_renameat);
 
-/*
- * An xattrwalk without @attr_name gives the fid for the lisxattr namespace
+/* An xattrwalk without @attr_name gives the fid for the lisxattr namespace
  */
 struct p9_fid *p9_client_xattrwalk(struct p9_fid *file_fid,
-				const char *attr_name, u64 *attr_size)
+				   const char *attr_name, u64 *attr_size)
 {
 	int err;
 	struct p9_req_t *req;
@@ -2025,11 +2032,11 @@
 		goto error;
 	}
 	p9_debug(P9_DEBUG_9P,
-		">>> TXATTRWALK file_fid %d, attr_fid %d name %s\n",
-		file_fid->fid, attr_fid->fid, attr_name);
+		 ">>> TXATTRWALK file_fid %d, attr_fid %d name '%s'\n",
+		 file_fid->fid, attr_fid->fid, attr_name);
 
 	req = p9_client_rpc(clnt, P9_TXATTRWALK, "dds",
-			file_fid->fid, attr_fid->fid, attr_name);
+			    file_fid->fid, attr_fid->fid, attr_name);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -2042,13 +2049,13 @@
 	}
 	p9_tag_remove(clnt, req);
 	p9_debug(P9_DEBUG_9P, "<<<  RXATTRWALK fid %d size %llu\n",
-		attr_fid->fid, *attr_size);
+		 attr_fid->fid, *attr_size);
 	return attr_fid;
 clunk_fid:
 	p9_client_clunk(attr_fid);
 	attr_fid = NULL;
 error:
-	if (attr_fid && (attr_fid != file_fid))
+	if (attr_fid && attr_fid != file_fid)
 		p9_fid_destroy(attr_fid);
 
 	return ERR_PTR(err);
@@ -2056,19 +2063,19 @@
 EXPORT_SYMBOL_GPL(p9_client_xattrwalk);
 
 int p9_client_xattrcreate(struct p9_fid *fid, const char *name,
-			u64 attr_size, int flags)
+			  u64 attr_size, int flags)
 {
 	int err;
 	struct p9_req_t *req;
 	struct p9_client *clnt;
 
 	p9_debug(P9_DEBUG_9P,
-		">>> TXATTRCREATE fid %d name  %s size %lld flag %d\n",
-		fid->fid, name, (long long)attr_size, flags);
+		 ">>> TXATTRCREATE fid %d name  %s size %llu flag %d\n",
+		 fid->fid, name, attr_size, flags);
 	err = 0;
 	clnt = fid->clnt;
 	req = p9_client_rpc(clnt, P9_TXATTRCREATE, "dsqd",
-			fid->fid, name, attr_size, flags);
+			    fid->fid, name, attr_size, flags);
 	if (IS_ERR(req)) {
 		err = PTR_ERR(req);
 		goto error;
@@ -2092,13 +2099,13 @@
 	iov_iter_kvec(&to, READ, &kv, 1, count);
 
 	p9_debug(P9_DEBUG_9P, ">>> TREADDIR fid %d offset %llu count %d\n",
-				fid->fid, (unsigned long long) offset, count);
+		 fid->fid, offset, count);
 
 	err = 0;
 	clnt = fid->clnt;
 
 	rsize = fid->iounit;
-	if (!rsize || rsize > clnt->msize-P9_READDIRHDRSZ)
+	if (!rsize || rsize > clnt->msize - P9_READDIRHDRSZ)
 		rsize = clnt->msize - P9_READDIRHDRSZ;
 
 	if (count < rsize)
@@ -2106,8 +2113,7 @@
 
 	/* Don't bother zerocopy for small IO (< 1024) */
 	if (clnt->trans_mod->zc_request && rsize > 1024) {
-		/*
-		 * response header len is 11
+		/* response header len is 11
 		 * PDU Header(7) + IO Size (4)
 		 */
 		req = p9_client_zc_rpc(clnt, P9_TREADDIR, &to, NULL, rsize, 0,
@@ -2148,7 +2154,7 @@
 EXPORT_SYMBOL(p9_client_readdir);
 
 int p9_client_mknod_dotl(struct p9_fid *fid, const char *name, int mode,
-			dev_t rdev, kgid_t gid, struct p9_qid *qid)
+			 dev_t rdev, kgid_t gid, struct p9_qid *qid)
 {
 	int err;
 	struct p9_client *clnt;
@@ -2156,10 +2162,11 @@
 
 	err = 0;
 	clnt = fid->clnt;
-	p9_debug(P9_DEBUG_9P, ">>> TMKNOD fid %d name %s mode %d major %d "
-		"minor %d\n", fid->fid, name, mode, MAJOR(rdev), MINOR(rdev));
+	p9_debug(P9_DEBUG_9P,
+		 ">>> TMKNOD fid %d name %s mode %d major %d minor %d\n",
+		 fid->fid, name, mode, MAJOR(rdev), MINOR(rdev));
 	req = p9_client_rpc(clnt, P9_TMKNOD, "dsdddg", fid->fid, name, mode,
-		MAJOR(rdev), MINOR(rdev), gid);
+			    MAJOR(rdev), MINOR(rdev), gid);
 	if (IS_ERR(req))
 		return PTR_ERR(req);
 
@@ -2168,18 +2175,17 @@
 		trace_9p_protocol_dump(clnt, &req->rc);
 		goto error;
 	}
-	p9_debug(P9_DEBUG_9P, "<<< RMKNOD qid %x.%llx.%x\n", qid->type,
-				(unsigned long long)qid->path, qid->version);
+	p9_debug(P9_DEBUG_9P, "<<< RMKNOD qid %x.%llx.%x\n",
+		 qid->type, qid->path, qid->version);
 
 error:
 	p9_tag_remove(clnt, req);
 	return err;
-
 }
 EXPORT_SYMBOL(p9_client_mknod_dotl);
 
 int p9_client_mkdir_dotl(struct p9_fid *fid, const char *name, int mode,
-				kgid_t gid, struct p9_qid *qid)
+			 kgid_t gid, struct p9_qid *qid)
 {
 	int err;
 	struct p9_client *clnt;
@@ -2189,8 +2195,8 @@
 	clnt = fid->clnt;
 	p9_debug(P9_DEBUG_9P, ">>> TMKDIR fid %d name %s mode %d gid %d\n",
 		 fid->fid, name, mode, from_kgid(&init_user_ns, gid));
-	req = p9_client_rpc(clnt, P9_TMKDIR, "dsdg", fid->fid, name, mode,
-		gid);
+	req = p9_client_rpc(clnt, P9_TMKDIR, "dsdg",
+			    fid->fid, name, mode, gid);
 	if (IS_ERR(req))
 		return PTR_ERR(req);
 
@@ -2200,12 +2206,11 @@
 		goto error;
 	}
 	p9_debug(P9_DEBUG_9P, "<<< RMKDIR qid %x.%llx.%x\n", qid->type,
-				(unsigned long long)qid->path, qid->version);
+		 qid->path, qid->version);
 
 error:
 	p9_tag_remove(clnt, req);
 	return err;
-
 }
 EXPORT_SYMBOL(p9_client_mkdir_dotl);
 
@@ -2217,14 +2222,14 @@
 
 	err = 0;
 	clnt = fid->clnt;
-	p9_debug(P9_DEBUG_9P, ">>> TLOCK fid %d type %i flags %d "
-			"start %lld length %lld proc_id %d client_id %s\n",
-			fid->fid, flock->type, flock->flags, flock->start,
-			flock->length, flock->proc_id, flock->client_id);
+	p9_debug(P9_DEBUG_9P,
+		 ">>> TLOCK fid %d type %i flags %d start %lld length %lld proc_id %d client_id %s\n",
+		 fid->fid, flock->type, flock->flags, flock->start,
+		 flock->length, flock->proc_id, flock->client_id);
 
 	req = p9_client_rpc(clnt, P9_TLOCK, "dbdqqds", fid->fid, flock->type,
-				flock->flags, flock->start, flock->length,
-					flock->proc_id, flock->client_id);
+			    flock->flags, flock->start, flock->length,
+			    flock->proc_id, flock->client_id);
 
 	if (IS_ERR(req))
 		return PTR_ERR(req);
@@ -2238,7 +2243,6 @@
 error:
 	p9_tag_remove(clnt, req);
 	return err;
-
 }
 EXPORT_SYMBOL(p9_client_lock_dotl);
 
@@ -2250,12 +2254,14 @@
 
 	err = 0;
 	clnt = fid->clnt;
-	p9_debug(P9_DEBUG_9P, ">>> TGETLOCK fid %d, type %i start %lld "
-		"length %lld proc_id %d client_id %s\n", fid->fid, glock->type,
-		glock->start, glock->length, glock->proc_id, glock->client_id);
-
-	req = p9_client_rpc(clnt, P9_TGETLOCK, "dbqqds", fid->fid,  glock->type,
-		glock->start, glock->length, glock->proc_id, glock->client_id);
+	p9_debug(P9_DEBUG_9P,
+		 ">>> TGETLOCK fid %d, type %i start %lld length %lld proc_id %d client_id %s\n",
+		 fid->fid, glock->type, glock->start, glock->length,
+		 glock->proc_id, glock->client_id);
+
+	req = p9_client_rpc(clnt, P9_TGETLOCK, "dbqqds", fid->fid,
+			    glock->type, glock->start, glock->length,
+			    glock->proc_id, glock->client_id);
 
 	if (IS_ERR(req))
 		return PTR_ERR(req);
@@ -2267,9 +2273,10 @@
 		trace_9p_protocol_dump(clnt, &req->rc);
 		goto error;
 	}
-	p9_debug(P9_DEBUG_9P, "<<< RGETLOCK type %i start %lld length %lld "
-		"proc_id %d client_id %s\n", glock->type, glock->start,
-		glock->length, glock->proc_id, glock->client_id);
+	p9_debug(P9_DEBUG_9P,
+		 "<<< RGETLOCK type %i start %lld length %lld proc_id %d client_id %s\n",
+		 glock->type, glock->start, glock->length,
+		 glock->proc_id, glock->client_id);
 error:
 	p9_tag_remove(clnt, req);
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/error.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/error.c
@@ -185,7 +185,7 @@
 		INIT_HLIST_HEAD(&hash_errmap[bucket]);
 
 	/* load initial error map into hash table */
-	for (c = errmap; c->name != NULL; c++) {
+	for (c = errmap; c->name; c++) {
 		c->namelen = strlen(c->name);
 		bucket = jhash(c->name, c->namelen, 0) % ERRHASHSZ;
 		INIT_HLIST_NODE(&c->list);
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/mod.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/mod.c
@@ -24,13 +24,13 @@
 #include <linux/spinlock.h>
 
 #ifdef CONFIG_NET_9P_DEBUG
-unsigned int p9_debug_level = 0;	/* feature-rific global debug level  */
+unsigned int p9_debug_level;	/* feature-rific global debug level  */
 EXPORT_SYMBOL(p9_debug_level);
 module_param_named(debug, p9_debug_level, uint, 0);
 MODULE_PARM_DESC(debug, "9P debugging level");
 
 void _p9_debug(enum p9_debug_flags level, const char *func,
-		const char *fmt, ...)
+	       const char *fmt, ...)
 {
 	struct va_format vaf;
 	va_list args;
@@ -53,10 +53,7 @@
 EXPORT_SYMBOL(_p9_debug);
 #endif
 
-/*
- * Dynamic Transport Registration Routines
- *
- */
+/* Dynamic Transport Registration Routines */
 
 static DEFINE_SPINLOCK(v9fs_trans_lock);
 static LIST_HEAD(v9fs_trans_list);
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/protocol.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/protocol.c
@@ -46,6 +46,7 @@
 size_t pdu_read(struct p9_fcall *pdu, void *data, size_t size)
 {
 	size_t len = min(pdu->size - pdu->offset, size);
+
 	memcpy(data, &pdu->sdata[pdu->offset], len);
 	pdu->offset += len;
 	return size - len;
@@ -54,6 +55,7 @@
 static size_t pdu_write(struct p9_fcall *pdu, const void *data, size_t size)
 {
 	size_t len = min(pdu->capacity - pdu->size, size);
+
 	memcpy(&pdu->sdata[pdu->size], data, len);
 	pdu->size += len;
 	return size - len;
@@ -64,6 +66,7 @@
 {
 	size_t len = min(pdu->capacity - pdu->size, size);
 	struct iov_iter i = *from;
+
 	if (!copy_from_iter_full(&pdu->sdata[pdu->size], len, &i))
 		len = 0;
 
@@ -71,26 +74,25 @@
 	return size - len;
 }
 
-/*
-	b - int8_t
-	w - int16_t
-	d - int32_t
-	q - int64_t
-	s - string
-	u - numeric uid
-	g - numeric gid
-	S - stat
-	Q - qid
-	D - data blob (int32_t size followed by void *, results are not freed)
-	T - array of strings (int16_t count, followed by strings)
-	R - array of qids (int16_t count, followed by qids)
-	A - stat for 9p2000.L (p9_stat_dotl)
-	? - if optional = 1, continue parsing
-*/
+/*	b - int8_t
+ *	w - int16_t
+ *	d - int32_t
+ *	q - int64_t
+ *	s - string
+ *	u - numeric uid
+ *	g - numeric gid
+ *	S - stat
+ *	Q - qid
+ *	D - data blob (int32_t size followed by void *, results are not freed)
+ *	T - array of strings (int16_t count, followed by strings)
+ *	R - array of qids (int16_t count, followed by qids)
+ *	A - stat for 9p2000.L (p9_stat_dotl)
+ *	? - if optional = 1, continue parsing
+ */
 
 static int
 p9pdu_vreadf(struct p9_fcall *pdu, int proto_version, const char *fmt,
-	va_list ap)
+	     va_list ap)
 {
 	const char *ptr;
 	int errcode = 0;
@@ -228,6 +230,8 @@
 				uint16_t *nwname = va_arg(ap, uint16_t *);
 				char ***wnames = va_arg(ap, char ***);
 
+				*wnames = NULL;
+
 				errcode = p9pdu_readf(pdu, proto_version,
 								"w", nwname);
 				if (!errcode) {
@@ -237,6 +241,8 @@
 							  GFP_NOFS);
 					if (!*wnames)
 						errcode = -ENOMEM;
+					else
+						(*wnames)[0] = NULL;
 				}
 
 				if (!errcode) {
@@ -248,8 +254,10 @@
 								proto_version,
 								"s",
 								&(*wnames)[i]);
-						if (errcode)
+						if (errcode) {
+							(*wnames)[i] = NULL;
 							break;
+						}
 					}
 				}
 
@@ -257,11 +265,14 @@
 					if (*wnames) {
 						int i;
 
-						for (i = 0; i < *nwname; i++)
+						for (i = 0; i < *nwname; i++) {
+							if (!(*wnames)[i])
+								break;
 							kfree((*wnames)[i]);
+						}
+						kfree(*wnames);
+						*wnames = NULL;
 					}
-					kfree(*wnames);
-					*wnames = NULL;
 				}
 			}
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/protocol.h
+++ linux-xilinx-zynqmp-5.15.0/net/9p/protocol.h
@@ -11,7 +11,7 @@
  */
 
 int p9pdu_vwritef(struct p9_fcall *pdu, int proto_version, const char *fmt,
-								va_list ap);
+		  va_list ap);
 int p9pdu_readf(struct p9_fcall *pdu, int proto_version, const char *fmt, ...);
 int p9pdu_prepare(struct p9_fcall *pdu, int16_t tag, int8_t type);
 int p9pdu_finalize(struct p9_client *clnt, struct p9_fcall *pdu);
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/trans_common.h
+++ linux-xilinx-zynqmp-5.15.0/net/9p/trans_common.h
@@ -12,4 +12,4 @@
  *
  */
 
-void p9_release_pages(struct page **, int);
+void p9_release_pages(struct page **pages, int nr_pages);
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/trans_fd.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/trans_fd.c
@@ -93,6 +93,7 @@
  * @mux_list: list link for mux to manage multiple connections (?)
  * @client: reference to client instance for this connection
  * @err: error state
+ * @req_lock: lock protecting req_list and requests statuses
  * @req_list: accounting for requests which have been sent
  * @unsent_req_list: accounting for requests that haven't been sent
  * @rreq: read request
@@ -116,11 +117,12 @@
 	struct list_head mux_list;
 	struct p9_client *client;
 	int err;
+	spinlock_t req_lock;
 	struct list_head req_list;
 	struct list_head unsent_req_list;
 	struct p9_req_t *rreq;
 	struct p9_req_t *wreq;
-	char tmp_buf[7];
+	char tmp_buf[P9_HDRSZ];
 	struct p9_fcall rc;
 	int wpos;
 	int wsize;
@@ -191,10 +193,10 @@
 
 	p9_debug(P9_DEBUG_ERROR, "mux %p err %d\n", m, err);
 
-	spin_lock(&m->client->lock);
+	spin_lock(&m->req_lock);
 
 	if (m->err) {
-		spin_unlock(&m->client->lock);
+		spin_unlock(&m->req_lock);
 		return;
 	}
 
@@ -202,11 +204,15 @@
 
 	list_for_each_entry_safe(req, rtmp, &m->req_list, req_list) {
 		list_move(&req->req_list, &cancel_list);
+		req->status = REQ_STATUS_ERROR;
 	}
 	list_for_each_entry_safe(req, rtmp, &m->unsent_req_list, req_list) {
 		list_move(&req->req_list, &cancel_list);
+		req->status = REQ_STATUS_ERROR;
 	}
 
+	spin_unlock(&m->req_lock);
+
 	list_for_each_entry_safe(req, rtmp, &cancel_list, req_list) {
 		p9_debug(P9_DEBUG_ERROR, "call back req %p\n", req);
 		list_del(&req->req_list);
@@ -214,7 +220,6 @@
 			req->t_err = err;
 		p9_client_cb(m->client, req, REQ_STATUS_ERROR);
 	}
-	spin_unlock(&m->client->lock);
 }
 
 static __poll_t
@@ -290,7 +295,7 @@
 	if (!m->rc.sdata) {
 		m->rc.sdata = m->tmp_buf;
 		m->rc.offset = 0;
-		m->rc.capacity = 7; /* start by reading header */
+		m->rc.capacity = P9_HDRSZ; /* start by reading header */
 	}
 
 	clear_bit(Rpending, &m->wsched);
@@ -313,7 +318,7 @@
 		p9_debug(P9_DEBUG_TRANS, "got new header\n");
 
 		/* Header size */
-		m->rc.size = 7;
+		m->rc.size = P9_HDRSZ;
 		err = p9_parse_header(&m->rc, &m->rc.size, NULL, NULL, 0);
 		if (err) {
 			p9_debug(P9_DEBUG_ERROR,
@@ -345,6 +350,7 @@
 			p9_debug(P9_DEBUG_ERROR,
 				 "No recv fcall for tag %d (req %p), disconnecting!\n",
 				 m->rc.tag, m->rreq);
+			p9_req_put(m->client, m->rreq);
 			m->rreq = NULL;
 			err = -EIO;
 			goto error;
@@ -360,7 +366,7 @@
 	if ((m->rreq) && (m->rc.offset == m->rc.capacity)) {
 		p9_debug(P9_DEBUG_TRANS, "got new packet\n");
 		m->rreq->rc.size = m->rc.offset;
-		spin_lock(&m->client->lock);
+		spin_lock(&m->req_lock);
 		if (m->rreq->status == REQ_STATUS_SENT) {
 			list_del(&m->rreq->req_list);
 			p9_client_cb(m->client, m->rreq, REQ_STATUS_RCVD);
@@ -369,18 +375,18 @@
 			p9_debug(P9_DEBUG_TRANS,
 				 "Ignore replies associated with a cancelled request\n");
 		} else {
-			spin_unlock(&m->client->lock);
+			spin_unlock(&m->req_lock);
 			p9_debug(P9_DEBUG_ERROR,
 				 "Request tag %d errored out while we were reading the reply\n",
 				 m->rc.tag);
 			err = -EIO;
 			goto error;
 		}
-		spin_unlock(&m->client->lock);
+		spin_unlock(&m->req_lock);
 		m->rc.sdata = NULL;
 		m->rc.offset = 0;
 		m->rc.capacity = 0;
-		p9_req_put(m->rreq);
+		p9_req_put(m->client, m->rreq);
 		m->rreq = NULL;
 	}
 
@@ -454,10 +460,10 @@
 	}
 
 	if (!m->wsize) {
-		spin_lock(&m->client->lock);
+		spin_lock(&m->req_lock);
 		if (list_empty(&m->unsent_req_list)) {
 			clear_bit(Wworksched, &m->wsched);
-			spin_unlock(&m->client->lock);
+			spin_unlock(&m->req_lock);
 			return;
 		}
 
@@ -472,7 +478,7 @@
 		m->wpos = 0;
 		p9_req_get(req);
 		m->wreq = req;
-		spin_unlock(&m->client->lock);
+		spin_unlock(&m->req_lock);
 	}
 
 	p9_debug(P9_DEBUG_TRANS, "mux %p pos %d size %d\n",
@@ -494,7 +500,7 @@
 	m->wpos += err;
 	if (m->wpos == m->wsize) {
 		m->wpos = m->wsize = 0;
-		p9_req_put(m->wreq);
+		p9_req_put(m->client, m->wreq);
 		m->wreq = NULL;
 	}
 
@@ -589,6 +595,7 @@
 	INIT_LIST_HEAD(&m->mux_list);
 	m->client = client;
 
+	spin_lock_init(&m->req_lock);
 	INIT_LIST_HEAD(&m->req_list);
 	INIT_LIST_HEAD(&m->unsent_req_list);
 	INIT_WORK(&m->rq, p9_read_work);
@@ -670,10 +677,10 @@
 	if (m->err < 0)
 		return m->err;
 
-	spin_lock(&client->lock);
+	spin_lock(&m->req_lock);
 	req->status = REQ_STATUS_UNSENT;
 	list_add_tail(&req->req_list, &m->unsent_req_list);
-	spin_unlock(&client->lock);
+	spin_unlock(&m->req_lock);
 
 	if (test_and_clear_bit(Wpending, &m->wsched))
 		n = EPOLLOUT;
@@ -688,33 +695,38 @@
 
 static int p9_fd_cancel(struct p9_client *client, struct p9_req_t *req)
 {
+	struct p9_trans_fd *ts = client->trans;
+	struct p9_conn *m = &ts->conn;
 	int ret = 1;
 
 	p9_debug(P9_DEBUG_TRANS, "client %p req %p\n", client, req);
 
-	spin_lock(&client->lock);
+	spin_lock(&m->req_lock);
 
 	if (req->status == REQ_STATUS_UNSENT) {
 		list_del(&req->req_list);
 		req->status = REQ_STATUS_FLSHD;
-		p9_req_put(req);
+		p9_req_put(client, req);
 		ret = 0;
 	}
-	spin_unlock(&client->lock);
+	spin_unlock(&m->req_lock);
 
 	return ret;
 }
 
 static int p9_fd_cancelled(struct p9_client *client, struct p9_req_t *req)
 {
+	struct p9_trans_fd *ts = client->trans;
+	struct p9_conn *m = &ts->conn;
+
 	p9_debug(P9_DEBUG_TRANS, "client %p req %p\n", client, req);
 
-	spin_lock(&client->lock);
+	spin_lock(&m->req_lock);
 	/* Ignore cancelled request if message has been received
 	 * before lock.
 	 */
 	if (req->status == REQ_STATUS_RCVD) {
-		spin_unlock(&client->lock);
+		spin_unlock(&m->req_lock);
 		return 0;
 	}
 
@@ -723,8 +735,9 @@
 	 */
 	list_del(&req->req_list);
 	req->status = REQ_STATUS_FLSHD;
-	spin_unlock(&client->lock);
-	p9_req_put(req);
+	spin_unlock(&m->req_lock);
+
+	p9_req_put(client, req);
 
 	return 0;
 }
@@ -822,11 +835,21 @@
 		goto out_free_ts;
 	if (!(ts->rd->f_mode & FMODE_READ))
 		goto out_put_rd;
+	/* Prevent workers from hanging on IO when fd is a pipe.
+	 * It's technically possible for userspace or concurrent mounts to
+	 * modify this flag concurrently, which will likely result in a
+	 * broken filesystem. However, just having bad flags here should
+	 * not crash the kernel or cause any other sort of bug, so mark this
+	 * particular data race as intentional so that tooling (like KCSAN)
+	 * can allow it and detect further problems.
+	 */
+	data_race(ts->rd->f_flags |= O_NONBLOCK);
 	ts->wr = fget(wfd);
 	if (!ts->wr)
 		goto out_put_rd;
 	if (!(ts->wr->f_mode & FMODE_WRITE))
 		goto out_put_wr;
+	data_race(ts->wr->f_flags |= O_NONBLOCK);
 
 	client->trans = ts;
 	client->status = Connected;
@@ -848,8 +871,10 @@
 	struct file *file;
 
 	p = kzalloc(sizeof(struct p9_trans_fd), GFP_KERNEL);
-	if (!p)
+	if (!p) {
+		sock_release(csocket);
 		return -ENOMEM;
+	}
 
 	csocket->sk->sk_allocation = GFP_NOIO;
 	file = sock_alloc_file(csocket, 0, NULL);
@@ -885,12 +910,12 @@
 	p9_mux_poll_stop(m);
 	cancel_work_sync(&m->rq);
 	if (m->rreq) {
-		p9_req_put(m->rreq);
+		p9_req_put(m->client, m->rreq);
 		m->rreq = NULL;
 	}
 	cancel_work_sync(&m->wq);
 	if (m->wreq) {
-		p9_req_put(m->wreq);
+		p9_req_put(m->client, m->wreq);
 		m->wreq = NULL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/trans_rdma.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/trans_rdma.c
@@ -352,7 +352,7 @@
 			    c->busa, c->req->tc.size,
 			    DMA_TO_DEVICE);
 	up(&rdma->sq_sem);
-	p9_req_put(c->req);
+	p9_req_put(client, c->req);
 	kfree(c);
 }
 
@@ -388,6 +388,7 @@
 	struct p9_trans_rdma *rdma = client->trans;
 	struct ib_recv_wr wr;
 	struct ib_sge sge;
+	int ret;
 
 	c->busa = ib_dma_map_single(rdma->cm_id->device,
 				    c->rc.sdata, client->msize,
@@ -405,7 +406,12 @@
 	wr.wr_cqe = &c->cqe;
 	wr.sg_list = &sge;
 	wr.num_sge = 1;
-	return ib_post_recv(rdma->qp, &wr, NULL);
+
+	ret = ib_post_recv(rdma->qp, &wr, NULL);
+	if (ret)
+		ib_dma_unmap_single(rdma->cm_id->device, c->busa,
+				    client->msize, DMA_FROM_DEVICE);
+	return ret;
 
  error:
 	p9_debug(P9_DEBUG_ERROR, "EIO\n");
@@ -502,7 +508,7 @@
 
 	if (down_interruptible(&rdma->sq_sem)) {
 		err = -EINTR;
-		goto send_error;
+		goto dma_unmap;
 	}
 
 	/* Mark request as `sent' *before* we actually send it,
@@ -512,11 +518,14 @@
 	req->status = REQ_STATUS_SENT;
 	err = ib_post_send(rdma->qp, &wr, NULL);
 	if (err)
-		goto send_error;
+		goto dma_unmap;
 
 	/* Success */
 	return 0;
 
+dma_unmap:
+	ib_dma_unmap_single(rdma->cm_id->device, c->busa,
+			    c->req->tc.size, DMA_TO_DEVICE);
  /* Handle errors that happened during or while preparing the send: */
  send_error:
 	req->status = REQ_STATUS_ERROR;
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/trans_virtio.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/trans_virtio.c
@@ -199,7 +199,7 @@
 /* Reply won't come, so drop req ref */
 static int p9_virtio_cancelled(struct p9_client *client, struct p9_req_t *req)
 {
-	p9_req_put(req);
+	p9_req_put(client, req);
 	return 0;
 }
 
@@ -399,7 +399,7 @@
 	struct page **in_pages = NULL, **out_pages = NULL;
 	struct virtio_chan *chan = client->trans;
 	struct scatterlist *sgs[4];
-	size_t offs;
+	size_t offs = 0;
 	int need_drop = 0;
 	int kicked = 0;
 
@@ -523,7 +523,7 @@
 	kvfree(out_pages);
 	if (!kicked) {
 		/* reply won't come */
-		p9_req_put(req);
+		p9_req_put(client, req);
 	}
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/9p/trans_xen.c
+++ linux-xilinx-zynqmp-5.15.0/net/9p/trans_xen.c
@@ -186,7 +186,7 @@
 	ring->intf->out_prod = prod;
 	spin_unlock_irqrestore(&ring->lock, flags);
 	notify_remote_via_irq(ring->irq);
-	p9_req_put(p9_req);
+	p9_req_put(client, p9_req);
 
 	return 0;
 }
@@ -231,6 +231,14 @@
 			continue;
 		}
 
+		if (h.size > req->rc.capacity) {
+			dev_warn(&priv->dev->dev,
+				 "requested packet size too big: %d for tag %d with capacity %zd\n",
+				 h.size, h.tag, req->rc.capacity);
+			req->status = REQ_STATUS_ERROR;
+			goto recv_error;
+		}
+
 		memcpy(&req->rc, &h, sizeof(h));
 		req->rc.offset = 0;
 
@@ -240,6 +248,7 @@
 				     masked_prod, &masked_cons,
 				     XEN_9PFS_RING_SIZE(ring));
 
+recv_error:
 		virt_mb();
 		cons += h.size;
 		ring->intf->in_cons = cons;
@@ -291,10 +300,14 @@
 	write_unlock(&xen_9pfs_lock);
 
 	for (i = 0; i < priv->num_rings; i++) {
+		struct xen_9pfs_dataring *ring = &priv->rings[i];
+
+		cancel_work_sync(&ring->work);
+
 		if (!priv->rings[i].intf)
 			break;
 		if (priv->rings[i].irq > 0)
-			unbind_from_irqhandler(priv->rings[i].irq, priv->dev);
+			unbind_from_irqhandler(priv->rings[i].irq, ring);
 		if (priv->rings[i].data.in) {
 			for (j = 0;
 			     j < (1 << priv->rings[i].intf->ring_order);
@@ -304,9 +317,9 @@
 				ref = priv->rings[i].intf->ref[j];
 				gnttab_end_foreign_access(ref, 0, 0);
 			}
-			free_pages((unsigned long)priv->rings[i].data.in,
-				   priv->rings[i].intf->ring_order -
-				   (PAGE_SHIFT - XEN_PAGE_SHIFT));
+			free_pages_exact(priv->rings[i].data.in,
+				   1UL << (priv->rings[i].intf->ring_order +
+					   XEN_PAGE_SHIFT));
 		}
 		gnttab_end_foreign_access(priv->rings[i].ref, 0, 0);
 		free_page((unsigned long)priv->rings[i].intf);
@@ -345,8 +358,8 @@
 	if (ret < 0)
 		goto out;
 	ring->ref = ret;
-	bytes = (void *)__get_free_pages(GFP_KERNEL | __GFP_ZERO,
-			order - (PAGE_SHIFT - XEN_PAGE_SHIFT));
+	bytes = alloc_pages_exact(1UL << (order + XEN_PAGE_SHIFT),
+				  GFP_KERNEL | __GFP_ZERO);
 	if (!bytes) {
 		ret = -ENOMEM;
 		goto out;
@@ -377,28 +390,31 @@
 	if (bytes) {
 		for (i--; i >= 0; i--)
 			gnttab_end_foreign_access(ring->intf->ref[i], 0, 0);
-		free_pages((unsigned long)bytes,
-			   ring->intf->ring_order -
-			   (PAGE_SHIFT - XEN_PAGE_SHIFT));
+		free_pages_exact(bytes, 1UL << (order + XEN_PAGE_SHIFT));
 	}
 	gnttab_end_foreign_access(ring->ref, 0, 0);
 	free_page((unsigned long)ring->intf);
 	return ret;
 }
 
-static int xen_9pfs_front_probe(struct xenbus_device *dev,
-				const struct xenbus_device_id *id)
+static int xen_9pfs_front_init(struct xenbus_device *dev)
 {
 	int ret, i;
 	struct xenbus_transaction xbt;
-	struct xen_9pfs_front_priv *priv = NULL;
-	char *versions;
+	struct xen_9pfs_front_priv *priv = dev_get_drvdata(&dev->dev);
+	char *versions, *v;
 	unsigned int max_rings, max_ring_order, len = 0;
 
 	versions = xenbus_read(XBT_NIL, dev->otherend, "versions", &len);
 	if (IS_ERR(versions))
 		return PTR_ERR(versions);
-	if (strcmp(versions, "1")) {
+	for (v = versions; *v; v++) {
+		if (simple_strtoul(v, &v, 10) == 1) {
+			v = NULL;
+			break;
+		}
+	}
+	if (v) {
 		kfree(versions);
 		return -EINVAL;
 	}
@@ -413,11 +429,6 @@
 	if (p9_xen_trans.maxsize > XEN_FLEX_RING_SIZE(max_ring_order))
 		p9_xen_trans.maxsize = XEN_FLEX_RING_SIZE(max_ring_order) / 2;
 
-	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-
-	priv->dev = dev;
 	priv->num_rings = XEN_9PFS_NUM_RINGS;
 	priv->rings = kcalloc(priv->num_rings, sizeof(*priv->rings),
 			      GFP_KERNEL);
@@ -476,23 +487,36 @@
 		goto error;
 	}
 
-	write_lock(&xen_9pfs_lock);
-	list_add_tail(&priv->list, &xen_9pfs_devs);
-	write_unlock(&xen_9pfs_lock);
-	dev_set_drvdata(&dev->dev, priv);
 	xenbus_switch_state(dev, XenbusStateInitialised);
-
 	return 0;
 
  error_xenbus:
 	xenbus_transaction_end(xbt, 1);
 	xenbus_dev_fatal(dev, ret, "writing xenstore");
  error:
-	dev_set_drvdata(&dev->dev, NULL);
 	xen_9pfs_front_free(priv);
 	return ret;
 }
 
+static int xen_9pfs_front_probe(struct xenbus_device *dev,
+				const struct xenbus_device_id *id)
+{
+	struct xen_9pfs_front_priv *priv = NULL;
+
+	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	dev_set_drvdata(&dev->dev, priv);
+
+	write_lock(&xen_9pfs_lock);
+	list_add_tail(&priv->list, &xen_9pfs_devs);
+	write_unlock(&xen_9pfs_lock);
+
+	return 0;
+}
+
 static int xen_9pfs_front_resume(struct xenbus_device *dev)
 {
 	dev_warn(&dev->dev, "suspend/resume unsupported\n");
@@ -511,6 +535,10 @@
 		break;
 
 	case XenbusStateInitWait:
+		if (dev->state != XenbusStateInitialising)
+			break;
+
+		xen_9pfs_front_init(dev);
 		break;
 
 	case XenbusStateConnected:
--- linux-xilinx-zynqmp-5.15.0.orig/net/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/Kconfig
@@ -204,7 +204,6 @@
 source "net/netfilter/Kconfig"
 source "net/ipv4/netfilter/Kconfig"
 source "net/ipv6/netfilter/Kconfig"
-source "net/decnet/netfilter/Kconfig"
 source "net/bridge/netfilter/Kconfig"
 
 endif
@@ -221,7 +220,6 @@
 source "net/bridge/Kconfig"
 source "net/dsa/Kconfig"
 source "net/8021q/Kconfig"
-source "net/decnet/Kconfig"
 source "net/llc/Kconfig"
 source "drivers/net/appletalk/Kconfig"
 source "net/x25/Kconfig"
--- linux-xilinx-zynqmp-5.15.0.orig/net/Kconfig.debug
+++ linux-xilinx-zynqmp-5.15.0/net/Kconfig.debug
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+config NET_DEV_REFCNT_TRACKER
+	bool "Enable net device refcount tracking"
+	depends on DEBUG_KERNEL && STACKTRACE_SUPPORT
+	select REF_TRACKER
+	default n
+	help
+	  Enable debugging feature to track device references.
+	  This adds memory and cpu costs.
--- linux-xilinx-zynqmp-5.15.0.orig/net/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/Makefile
@@ -38,7 +38,6 @@
 obj-$(CONFIG_STREAM_PARSER)	+= strparser/
 obj-$(CONFIG_ATM)		+= atm/
 obj-$(CONFIG_L2TP)		+= l2tp/
-obj-$(CONFIG_DECNET)		+= decnet/
 obj-$(CONFIG_PHONET)		+= phonet/
 ifneq ($(CONFIG_VLAN_8021Q),)
 obj-y				+= 8021q/
--- linux-xilinx-zynqmp-5.15.0.orig/net/appletalk/ddp.c
+++ linux-xilinx-zynqmp-5.15.0/net/appletalk/ddp.c
@@ -1812,15 +1812,14 @@
 		break;
 	}
 	case TIOCINQ: {
-		/*
-		 * These two are safe on a single CPU system as only
-		 * user tasks fiddle here
-		 */
-		struct sk_buff *skb = skb_peek(&sk->sk_receive_queue);
+		struct sk_buff *skb;
 		long amount = 0;
 
+		spin_lock_irq(&sk->sk_receive_queue.lock);
+		skb = skb_peek(&sk->sk_receive_queue);
 		if (skb)
 			amount = skb->len - sizeof(struct ddpehdr);
+		spin_unlock_irq(&sk->sk_receive_queue.lock);
 		rc = put_user(amount, (int __user *)argp);
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/atm/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/atm/ioctl.c
@@ -73,14 +73,17 @@
 	case SIOCINQ:
 	{
 		struct sk_buff *skb;
+		int amount;
 
 		if (sock->state != SS_CONNECTED) {
 			error = -EINVAL;
 			goto done;
 		}
+		spin_lock_irq(&sk->sk_receive_queue.lock);
 		skb = skb_peek(&sk->sk_receive_queue);
-		error = put_user(skb ? skb->len : 0,
-				 (int __user *)argp) ? -EFAULT : 0;
+		amount = skb ? skb->len : 0;
+		spin_unlock_irq(&sk->sk_receive_queue.lock);
+		error = put_user(amount, (int __user *)argp) ? -EFAULT : 0;
 		goto done;
 	}
 	case ATM_SETSC:
--- linux-xilinx-zynqmp-5.15.0.orig/net/atm/lec.c
+++ linux-xilinx-zynqmp-5.15.0/net/atm/lec.c
@@ -181,6 +181,7 @@
 lec_send(struct atm_vcc *vcc, struct sk_buff *skb)
 {
 	struct net_device *dev = skb->dev;
+	unsigned int len = skb->len;
 
 	ATM_SKB(skb)->vcc = vcc;
 	atm_account_tx(vcc, skb);
@@ -191,7 +192,7 @@
 	}
 
 	dev->stats.tx_packets++;
-	dev->stats.tx_bytes += skb->len;
+	dev->stats.tx_bytes += len;
 }
 
 static void lec_tx_timeout(struct net_device *dev, unsigned int txqueue)
--- linux-xilinx-zynqmp-5.15.0.orig/net/atm/mpc.c
+++ linux-xilinx-zynqmp-5.15.0/net/atm/mpc.c
@@ -1314,6 +1314,8 @@
 	holding_time = msg->content.eg_info.holding_time;
 	dprintk("(%s) entry = %p, holding_time = %u\n",
 		mpc->dev->name, entry, holding_time);
+	if (entry == NULL && !holding_time)
+		return;
 	if (entry == NULL && holding_time) {
 		entry = mpc->eg_ops->add_entry(msg, mpc);
 		mpc->eg_ops->put(entry);
--- linux-xilinx-zynqmp-5.15.0.orig/net/atm/mpoa_proc.c
+++ linux-xilinx-zynqmp-5.15.0/net/atm/mpoa_proc.c
@@ -219,11 +219,12 @@
 	if (!page)
 		return -ENOMEM;
 
-	for (p = page, len = 0; len < nbytes; p++, len++) {
+	for (p = page, len = 0; len < nbytes; p++) {
 		if (get_user(*p, buff++)) {
 			free_page((unsigned long)page);
 			return -EFAULT;
 		}
+		len += 1;
 		if (*p == '\0' || *p == '\n')
 			break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/atm/resources.c
+++ linux-xilinx-zynqmp-5.15.0/net/atm/resources.c
@@ -400,6 +400,7 @@
 	return error;
 }
 
+#ifdef CONFIG_PROC_FS
 void *atm_dev_seq_start(struct seq_file *seq, loff_t *pos)
 {
 	mutex_lock(&atm_dev_mutex);
@@ -415,3 +416,4 @@
 {
 	return seq_list_next(v, &atm_devs, pos);
 }
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/ax25/af_ax25.c
+++ linux-xilinx-zynqmp-5.15.0/net/ax25/af_ax25.c
@@ -77,6 +77,7 @@
 {
 	ax25_dev *ax25_dev;
 	ax25_cb *s;
+	struct sock *sk;
 
 	if ((ax25_dev = ax25_dev_ax25dev(dev)) == NULL)
 		return;
@@ -85,11 +86,26 @@
 again:
 	ax25_for_each(s, &ax25_list) {
 		if (s->ax25_dev == ax25_dev) {
-			s->ax25_dev = NULL;
+			sk = s->sk;
+			if (!sk) {
+				spin_unlock_bh(&ax25_list_lock);
+				ax25_disconnect(s, ENETUNREACH);
+				s->ax25_dev = NULL;
+				spin_lock_bh(&ax25_list_lock);
+				goto again;
+			}
+			sock_hold(sk);
 			spin_unlock_bh(&ax25_list_lock);
+			lock_sock(sk);
 			ax25_disconnect(s, ENETUNREACH);
+			s->ax25_dev = NULL;
+			if (sk->sk_socket) {
+				dev_put(ax25_dev->dev);
+				ax25_dev_put(ax25_dev);
+			}
+			release_sock(sk);
 			spin_lock_bh(&ax25_list_lock);
-
+			sock_put(sk);
 			/* The entry could have been deleted from the
 			 * list meanwhile and thus the next pointer is
 			 * no longer valid.  Play it safe and restart
@@ -353,21 +369,25 @@
 	if (copy_from_user(&ax25_ctl, arg, sizeof(ax25_ctl)))
 		return -EFAULT;
 
-	if ((ax25_dev = ax25_addr_ax25dev(&ax25_ctl.port_addr)) == NULL)
-		return -ENODEV;
-
 	if (ax25_ctl.digi_count > AX25_MAX_DIGIS)
 		return -EINVAL;
 
 	if (ax25_ctl.arg > ULONG_MAX / HZ && ax25_ctl.cmd != AX25_KILL)
 		return -EINVAL;
 
+	ax25_dev = ax25_addr_ax25dev(&ax25_ctl.port_addr);
+	if (!ax25_dev)
+		return -ENODEV;
+
 	digi.ndigi = ax25_ctl.digi_count;
 	for (k = 0; k < digi.ndigi; k++)
 		digi.calls[k] = ax25_ctl.digi_addr[k];
 
-	if ((ax25 = ax25_find_cb(&ax25_ctl.source_addr, &ax25_ctl.dest_addr, &digi, ax25_dev->dev)) == NULL)
+	ax25 = ax25_find_cb(&ax25_ctl.source_addr, &ax25_ctl.dest_addr, &digi, ax25_dev->dev);
+	if (!ax25) {
+		ax25_dev_put(ax25_dev);
 		return -ENOTCONN;
+	}
 
 	switch (ax25_ctl.cmd) {
 	case AX25_KILL:
@@ -434,6 +454,7 @@
 	  }
 
 out_put:
+	ax25_dev_put(ax25_dev);
 	ax25_cb_put(ax25);
 	return ret;
 
@@ -534,7 +555,7 @@
 	ax25_cb *ax25;
 	struct net_device *dev;
 	char devname[IFNAMSIZ];
-	unsigned long opt;
+	unsigned int opt;
 	int res = 0;
 
 	if (level != SOL_AX25)
@@ -566,7 +587,7 @@
 		break;
 
 	case AX25_T1:
-		if (opt < 1 || opt > ULONG_MAX / HZ) {
+		if (opt < 1 || opt > UINT_MAX / HZ) {
 			res = -EINVAL;
 			break;
 		}
@@ -575,7 +596,7 @@
 		break;
 
 	case AX25_T2:
-		if (opt < 1 || opt > ULONG_MAX / HZ) {
+		if (opt < 1 || opt > UINT_MAX / HZ) {
 			res = -EINVAL;
 			break;
 		}
@@ -591,7 +612,7 @@
 		break;
 
 	case AX25_T3:
-		if (opt < 1 || opt > ULONG_MAX / HZ) {
+		if (opt < 1 || opt > UINT_MAX / HZ) {
 			res = -EINVAL;
 			break;
 		}
@@ -599,7 +620,7 @@
 		break;
 
 	case AX25_IDLE:
-		if (opt > ULONG_MAX / (60 * HZ)) {
+		if (opt > UINT_MAX / (60 * HZ)) {
 			res = -EINVAL;
 			break;
 		}
@@ -960,14 +981,16 @@
 {
 	struct sock *sk = sock->sk;
 	ax25_cb *ax25;
+	ax25_dev *ax25_dev;
 
 	if (sk == NULL)
 		return 0;
 
 	sock_hold(sk);
-	sock_orphan(sk);
 	lock_sock(sk);
+	sock_orphan(sk);
 	ax25 = sk_to_ax25(sk);
+	ax25_dev = ax25->ax25_dev;
 
 	if (sk->sk_type == SOCK_SEQPACKET) {
 		switch (ax25->state) {
@@ -1029,6 +1052,15 @@
 		sk->sk_state_change(sk);
 		ax25_destroy_socket(ax25);
 	}
+	if (ax25_dev) {
+		del_timer_sync(&ax25->timer);
+		del_timer_sync(&ax25->t1timer);
+		del_timer_sync(&ax25->t2timer);
+		del_timer_sync(&ax25->t3timer);
+		del_timer_sync(&ax25->idletimer);
+		dev_put(ax25_dev->dev);
+		ax25_dev_put(ax25_dev);
+	}
 
 	sock->sk   = NULL;
 	release_sock(sk);
@@ -1105,8 +1137,10 @@
 		}
 	}
 
-	if (ax25_dev != NULL)
+	if (ax25_dev) {
 		ax25_fillin_cb(ax25, ax25_dev);
+		dev_hold(ax25_dev->dev);
+	}
 
 done:
 	ax25_cb_add(ax25);
@@ -1336,8 +1370,10 @@
 {
 	struct sk_buff *skb;
 	struct sock *newsk;
+	ax25_dev *ax25_dev;
 	DEFINE_WAIT(wait);
 	struct sock *sk;
+	ax25_cb *ax25;
 	int err = 0;
 
 	if (sock->state != SS_UNCONNECTED)
@@ -1392,6 +1428,10 @@
 	kfree_skb(skb);
 	sk_acceptq_removed(sk);
 	newsock->state = SS_CONNECTED;
+	ax25 = sk_to_ax25(newsk);
+	ax25_dev = ax25->ax25_dev;
+	dev_hold(ax25_dev->dev);
+	ax25_dev_hold(ax25_dev);
 
 out:
 	release_sock(sk);
@@ -1620,9 +1660,12 @@
 			int flags)
 {
 	struct sock *sk = sock->sk;
-	struct sk_buff *skb;
+	struct sk_buff *skb, *last;
+	struct sk_buff_head *sk_queue;
 	int copied;
 	int err = 0;
+	int off = 0;
+	long timeo;
 
 	lock_sock(sk);
 	/*
@@ -1634,11 +1677,29 @@
 		goto out;
 	}
 
-	/* Now we can treat all alike */
-	skb = skb_recv_datagram(sk, flags & ~MSG_DONTWAIT,
-				flags & MSG_DONTWAIT, &err);
-	if (skb == NULL)
-		goto out;
+	/*  We need support for non-blocking reads. */
+	sk_queue = &sk->sk_receive_queue;
+	skb = __skb_try_recv_datagram(sk, sk_queue, flags, &off, &err, &last);
+	/* If no packet is available, release_sock(sk) and try again. */
+	if (!skb) {
+		if (err != -EAGAIN)
+			goto out;
+		release_sock(sk);
+		timeo = sock_rcvtimeo(sk, flags & MSG_DONTWAIT);
+		while (timeo && !__skb_wait_for_more_packets(sk, sk_queue, &err,
+							     &timeo, last)) {
+			skb = __skb_try_recv_datagram(sk, sk_queue, flags, &off,
+						      &err, &last);
+			if (skb)
+				break;
+
+			if (err != -EAGAIN)
+				goto done;
+		}
+		if (!skb)
+			goto done;
+		lock_sock(sk);
+	}
 
 	if (!sk_to_ax25(sk)->pidincl)
 		skb_pull(skb, 1);		/* Remove PID */
@@ -1685,6 +1746,7 @@
 out:
 	release_sock(sk);
 
+done:
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ax25/ax25_dev.c
+++ linux-xilinx-zynqmp-5.15.0/net/ax25/ax25_dev.c
@@ -37,6 +37,8 @@
 	for (ax25_dev = ax25_dev_list; ax25_dev != NULL; ax25_dev = ax25_dev->next)
 		if (ax25cmp(addr, (ax25_address *)ax25_dev->dev->dev_addr) == 0) {
 			res = ax25_dev;
+			ax25_dev_hold(ax25_dev);
+			break;
 		}
 	spin_unlock_bh(&ax25_dev_lock);
 
@@ -56,6 +58,7 @@
 		return;
 	}
 
+	refcount_set(&ax25_dev->refcount, 1);
 	dev->ax25_ptr     = ax25_dev;
 	ax25_dev->dev     = dev;
 	dev_hold(dev);
@@ -100,7 +103,7 @@
 	spin_lock_bh(&ax25_dev_lock);
 
 #ifdef CONFIG_AX25_DAMA_SLAVE
-	ax25_ds_del_timer(ax25_dev);
+	timer_shutdown_sync(&ax25_dev->dama.slave_timer);
 #endif
 
 	/*
@@ -115,7 +118,7 @@
 		spin_unlock_bh(&ax25_dev_lock);
 		dev->ax25_ptr = NULL;
 		dev_put(dev);
-		kfree(ax25_dev);
+		ax25_dev_put(ax25_dev);
 		return;
 	}
 
@@ -125,7 +128,7 @@
 			spin_unlock_bh(&ax25_dev_lock);
 			dev->ax25_ptr = NULL;
 			dev_put(dev);
-			kfree(ax25_dev);
+			ax25_dev_put(ax25_dev);
 			return;
 		}
 
@@ -133,6 +136,7 @@
 	}
 	spin_unlock_bh(&ax25_dev_lock);
 	dev->ax25_ptr = NULL;
+	ax25_dev_put(ax25_dev);
 }
 
 int ax25_fwd_ioctl(unsigned int cmd, struct ax25_fwd_struct *fwd)
@@ -144,20 +148,32 @@
 
 	switch (cmd) {
 	case SIOCAX25ADDFWD:
-		if ((fwd_dev = ax25_addr_ax25dev(&fwd->port_to)) == NULL)
+		fwd_dev = ax25_addr_ax25dev(&fwd->port_to);
+		if (!fwd_dev) {
+			ax25_dev_put(ax25_dev);
 			return -EINVAL;
-		if (ax25_dev->forward != NULL)
+		}
+		if (ax25_dev->forward) {
+			ax25_dev_put(fwd_dev);
+			ax25_dev_put(ax25_dev);
 			return -EINVAL;
+		}
 		ax25_dev->forward = fwd_dev->dev;
+		ax25_dev_put(fwd_dev);
+		ax25_dev_put(ax25_dev);
 		break;
 
 	case SIOCAX25DELFWD:
-		if (ax25_dev->forward == NULL)
+		if (!ax25_dev->forward) {
+			ax25_dev_put(ax25_dev);
 			return -EINVAL;
+		}
 		ax25_dev->forward = NULL;
+		ax25_dev_put(ax25_dev);
 		break;
 
 	default:
+		ax25_dev_put(ax25_dev);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ax25/ax25_route.c
+++ linux-xilinx-zynqmp-5.15.0/net/ax25/ax25_route.c
@@ -75,11 +75,13 @@
 	ax25_dev *ax25_dev;
 	int i;
 
-	if ((ax25_dev = ax25_addr_ax25dev(&route->port_addr)) == NULL)
-		return -EINVAL;
 	if (route->digi_count > AX25_MAX_DIGIS)
 		return -EINVAL;
 
+	ax25_dev = ax25_addr_ax25dev(&route->port_addr);
+	if (!ax25_dev)
+		return -EINVAL;
+
 	write_lock_bh(&ax25_route_lock);
 
 	ax25_rt = ax25_route_list;
@@ -91,6 +93,7 @@
 			if (route->digi_count != 0) {
 				if ((ax25_rt->digipeat = kmalloc(sizeof(ax25_digi), GFP_ATOMIC)) == NULL) {
 					write_unlock_bh(&ax25_route_lock);
+					ax25_dev_put(ax25_dev);
 					return -ENOMEM;
 				}
 				ax25_rt->digipeat->lastrepeat = -1;
@@ -101,6 +104,7 @@
 				}
 			}
 			write_unlock_bh(&ax25_route_lock);
+			ax25_dev_put(ax25_dev);
 			return 0;
 		}
 		ax25_rt = ax25_rt->next;
@@ -108,6 +112,7 @@
 
 	if ((ax25_rt = kmalloc(sizeof(ax25_route), GFP_ATOMIC)) == NULL) {
 		write_unlock_bh(&ax25_route_lock);
+		ax25_dev_put(ax25_dev);
 		return -ENOMEM;
 	}
 
@@ -120,6 +125,7 @@
 		if ((ax25_rt->digipeat = kmalloc(sizeof(ax25_digi), GFP_ATOMIC)) == NULL) {
 			write_unlock_bh(&ax25_route_lock);
 			kfree(ax25_rt);
+			ax25_dev_put(ax25_dev);
 			return -ENOMEM;
 		}
 		ax25_rt->digipeat->lastrepeat = -1;
@@ -132,6 +138,7 @@
 	ax25_rt->next   = ax25_route_list;
 	ax25_route_list = ax25_rt;
 	write_unlock_bh(&ax25_route_lock);
+	ax25_dev_put(ax25_dev);
 
 	return 0;
 }
@@ -173,6 +180,7 @@
 		}
 	}
 	write_unlock_bh(&ax25_route_lock);
+	ax25_dev_put(ax25_dev);
 
 	return 0;
 }
@@ -215,6 +223,7 @@
 
 out:
 	write_unlock_bh(&ax25_route_lock);
+	ax25_dev_put(ax25_dev);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ax25/ax25_subr.c
+++ linux-xilinx-zynqmp-5.15.0/net/ax25/ax25_subr.c
@@ -261,12 +261,20 @@
 {
 	ax25_clear_queues(ax25);
 
-	if (!ax25->sk || !sock_flag(ax25->sk, SOCK_DESTROY))
-		ax25_stop_heartbeat(ax25);
-	ax25_stop_t1timer(ax25);
-	ax25_stop_t2timer(ax25);
-	ax25_stop_t3timer(ax25);
-	ax25_stop_idletimer(ax25);
+	if (reason == ENETUNREACH) {
+		del_timer_sync(&ax25->timer);
+		del_timer_sync(&ax25->t1timer);
+		del_timer_sync(&ax25->t2timer);
+		del_timer_sync(&ax25->t3timer);
+		del_timer_sync(&ax25->idletimer);
+	} else {
+		if (!ax25->sk || !sock_flag(ax25->sk, SOCK_DESTROY))
+			ax25_stop_heartbeat(ax25);
+		ax25_stop_t1timer(ax25);
+		ax25_stop_t2timer(ax25);
+		ax25_stop_t3timer(ax25);
+		ax25_stop_idletimer(ax25);
+	}
 
 	ax25->state = AX25_STATE_0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/bat_iv_ogm.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/bat_iv_ogm.c
@@ -325,8 +325,7 @@
 	/* check if there is enough space for the optional TVLV */
 	next_buff_pos += ntohs(ogm_packet->tvlv_len);
 
-	return (next_buff_pos <= packet_len) &&
-	       (next_buff_pos <= BATADV_MAX_AGGREGATION_BYTES);
+	return next_buff_pos <= packet_len;
 }
 
 /* send a batman ogm to a given interface */
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/bat_v.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/bat_v.c
@@ -113,8 +113,6 @@
 batadv_v_hardif_neigh_init(struct batadv_hardif_neigh_node *hardif_neigh)
 {
 	ewma_throughput_init(&hardif_neigh->bat_v.throughput);
-	INIT_WORK(&hardif_neigh->bat_v.metric_work,
-		  batadv_v_elp_throughput_metric_update);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/bat_v_elp.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/bat_v_elp.c
@@ -18,6 +18,7 @@
 #include <linux/jiffies.h>
 #include <linux/kernel.h>
 #include <linux/kref.h>
+#include <linux/list.h>
 #include <linux/minmax.h>
 #include <linux/netdevice.h>
 #include <linux/nl80211.h>
@@ -27,6 +28,7 @@
 #include <linux/rcupdate.h>
 #include <linux/rtnetlink.h>
 #include <linux/skbuff.h>
+#include <linux/slab.h>
 #include <linux/stddef.h>
 #include <linux/string.h>
 #include <linux/types.h>
@@ -43,6 +45,18 @@
 #include "send.h"
 
 /**
+ * struct batadv_v_metric_queue_entry - list of hardif neighbors which require
+ *  and metric update
+ */
+struct batadv_v_metric_queue_entry {
+	/** @hardif_neigh: hardif neighbor scheduled for metric update */
+	struct batadv_hardif_neigh_node *hardif_neigh;
+
+	/** @list: list node for metric_queue */
+	struct list_head list;
+};
+
+/**
  * batadv_v_elp_start_timer() - restart timer for ELP periodic work
  * @hard_iface: the interface for which the timer has to be reset
  */
@@ -60,25 +74,36 @@
 /**
  * batadv_v_elp_get_throughput() - get the throughput towards a neighbour
  * @neigh: the neighbour for which the throughput has to be obtained
+ * @pthroughput: calculated throughput towards the given neighbour in multiples
+ *  of 100kpbs (a value of '1' equals 0.1Mbps, '10' equals 1Mbps, etc).
  *
- * Return: The throughput towards the given neighbour in multiples of 100kpbs
- *         (a value of '1' equals 0.1Mbps, '10' equals 1Mbps, etc).
+ * Return: true when value behind @pthroughput was set
  */
-static u32 batadv_v_elp_get_throughput(struct batadv_hardif_neigh_node *neigh)
+static bool batadv_v_elp_get_throughput(struct batadv_hardif_neigh_node *neigh,
+					u32 *pthroughput)
 {
 	struct batadv_hard_iface *hard_iface = neigh->if_incoming;
+	struct net_device *soft_iface = hard_iface->soft_iface;
 	struct ethtool_link_ksettings link_settings;
 	struct net_device *real_netdev;
 	struct station_info sinfo;
 	u32 throughput;
 	int ret;
 
+	/* don't query throughput when no longer associated with any
+	 * batman-adv interface
+	 */
+	if (!soft_iface)
+		return false;
+
 	/* if the user specified a customised value for this interface, then
 	 * return it directly
 	 */
 	throughput =  atomic_read(&hard_iface->bat_v.throughput_override);
-	if (throughput != 0)
-		return throughput;
+	if (throughput != 0) {
+		*pthroughput = throughput;
+		return true;
+	}
 
 	/* if this is a wireless device, then ask its throughput through
 	 * cfg80211 API
@@ -105,28 +130,39 @@
 			 * possible to delete this neighbor. For now set
 			 * the throughput metric to 0.
 			 */
-			return 0;
+			*pthroughput = 0;
+			return true;
 		}
 		if (ret)
 			goto default_throughput;
 
-		if (sinfo.filled & BIT(NL80211_STA_INFO_EXPECTED_THROUGHPUT))
-			return sinfo.expected_throughput / 100;
+		if (sinfo.filled & BIT(NL80211_STA_INFO_EXPECTED_THROUGHPUT)) {
+			*pthroughput = sinfo.expected_throughput / 100;
+			return true;
+		}
 
 		/* try to estimate the expected throughput based on reported tx
 		 * rates
 		 */
-		if (sinfo.filled & BIT(NL80211_STA_INFO_TX_BITRATE))
-			return cfg80211_calculate_bitrate(&sinfo.txrate) / 3;
+		if (sinfo.filled & BIT(NL80211_STA_INFO_TX_BITRATE)) {
+			*pthroughput = cfg80211_calculate_bitrate(&sinfo.txrate) / 3;
+			return true;
+		}
 
 		goto default_throughput;
 	}
 
+	/* only use rtnl_trylock because the elp worker will be cancelled while
+	 * the rntl_lock is held. the cancel_delayed_work_sync() would otherwise
+	 * wait forever when the elp work_item was started and it is then also
+	 * trying to rtnl_lock
+	 */
+	if (!rtnl_trylock())
+		return false;
+
 	/* if not a wifi interface, check if this device provides data via
 	 * ethtool (e.g. an Ethernet adapter)
 	 */
-	memset(&link_settings, 0, sizeof(link_settings));
-	rtnl_lock();
 	ret = __ethtool_get_link_ksettings(hard_iface->net_dev, &link_settings);
 	rtnl_unlock();
 	if (ret == 0) {
@@ -137,13 +173,15 @@
 			hard_iface->bat_v.flags &= ~BATADV_FULL_DUPLEX;
 
 		throughput = link_settings.base.speed;
-		if (throughput && throughput != SPEED_UNKNOWN)
-			return throughput * 10;
+		if (throughput && throughput != SPEED_UNKNOWN) {
+			*pthroughput = throughput * 10;
+			return true;
+		}
 	}
 
 default_throughput:
 	if (!(hard_iface->bat_v.flags & BATADV_WARNING_DEFAULT)) {
-		batadv_info(hard_iface->soft_iface,
+		batadv_info(soft_iface,
 			    "WiFi driver or ethtool info does not provide information about link speeds on interface %s, therefore defaulting to hardcoded throughput values of %u.%1u Mbps. Consider overriding the throughput manually or checking your driver.\n",
 			    hard_iface->net_dev->name,
 			    BATADV_THROUGHPUT_DEFAULT_VALUE / 10,
@@ -152,31 +190,26 @@
 	}
 
 	/* if none of the above cases apply, return the base_throughput */
-	return BATADV_THROUGHPUT_DEFAULT_VALUE;
+	*pthroughput = BATADV_THROUGHPUT_DEFAULT_VALUE;
+	return true;
 }
 
 /**
  * batadv_v_elp_throughput_metric_update() - worker updating the throughput
  *  metric of a single hop neighbour
- * @work: the work queue item
+ * @neigh: the neighbour to probe
  */
-void batadv_v_elp_throughput_metric_update(struct work_struct *work)
+static void
+batadv_v_elp_throughput_metric_update(struct batadv_hardif_neigh_node *neigh)
 {
-	struct batadv_hardif_neigh_node_bat_v *neigh_bat_v;
-	struct batadv_hardif_neigh_node *neigh;
-
-	neigh_bat_v = container_of(work, struct batadv_hardif_neigh_node_bat_v,
-				   metric_work);
-	neigh = container_of(neigh_bat_v, struct batadv_hardif_neigh_node,
-			     bat_v);
+	u32 throughput;
+	bool valid;
 
-	ewma_throughput_add(&neigh->bat_v.throughput,
-			    batadv_v_elp_get_throughput(neigh));
+	valid = batadv_v_elp_get_throughput(neigh, &throughput);
+	if (!valid)
+		return;
 
-	/* decrement refcounter to balance increment performed before scheduling
-	 * this task
-	 */
-	batadv_hardif_neigh_put(neigh);
+	ewma_throughput_add(&neigh->bat_v.throughput, throughput);
 }
 
 /**
@@ -250,14 +283,16 @@
  */
 static void batadv_v_elp_periodic_work(struct work_struct *work)
 {
+	struct batadv_v_metric_queue_entry *metric_entry;
+	struct batadv_v_metric_queue_entry *metric_safe;
 	struct batadv_hardif_neigh_node *hardif_neigh;
 	struct batadv_hard_iface *hard_iface;
 	struct batadv_hard_iface_bat_v *bat_v;
 	struct batadv_elp_packet *elp_packet;
+	struct list_head metric_queue;
 	struct batadv_priv *bat_priv;
 	struct sk_buff *skb;
 	u32 elp_interval;
-	bool ret;
 
 	bat_v = container_of(work, struct batadv_hard_iface_bat_v, elp_wq.work);
 	hard_iface = container_of(bat_v, struct batadv_hard_iface, bat_v);
@@ -293,6 +328,8 @@
 
 	atomic_inc(&hard_iface->bat_v.elp_seqno);
 
+	INIT_LIST_HEAD(&metric_queue);
+
 	/* The throughput metric is updated on each sent packet. This way, if a
 	 * node is dead and no longer sends packets, batman-adv is still able to
 	 * react timely to its death.
@@ -317,16 +354,28 @@
 
 		/* Reading the estimated throughput from cfg80211 is a task that
 		 * may sleep and that is not allowed in an rcu protected
-		 * context. Therefore schedule a task for that.
+		 * context. Therefore add it to metric_queue and process it
+		 * outside rcu protected context.
 		 */
-		ret = queue_work(batadv_event_workqueue,
-				 &hardif_neigh->bat_v.metric_work);
-
-		if (!ret)
+		metric_entry = kzalloc(sizeof(*metric_entry), GFP_ATOMIC);
+		if (!metric_entry) {
 			batadv_hardif_neigh_put(hardif_neigh);
+			continue;
+		}
+
+		metric_entry->hardif_neigh = hardif_neigh;
+		list_add(&metric_entry->list, &metric_queue);
 	}
 	rcu_read_unlock();
 
+	list_for_each_entry_safe(metric_entry, metric_safe, &metric_queue, list) {
+		batadv_v_elp_throughput_metric_update(metric_entry->hardif_neigh);
+
+		batadv_hardif_neigh_put(metric_entry->hardif_neigh);
+		list_del(&metric_entry->list);
+		kfree(metric_entry);
+	}
+
 restart_timer:
 	batadv_v_elp_start_timer(hard_iface);
 out:
@@ -507,7 +556,7 @@
 	struct batadv_priv *bat_priv = netdev_priv(if_incoming->soft_iface);
 	struct batadv_elp_packet *elp_packet;
 	struct batadv_hard_iface *primary_if;
-	struct ethhdr *ethhdr = (struct ethhdr *)skb_mac_header(skb);
+	struct ethhdr *ethhdr;
 	bool res;
 	int ret = NET_RX_DROP;
 
@@ -515,6 +564,7 @@
 	if (!res)
 		goto free_skb;
 
+	ethhdr = eth_hdr(skb);
 	if (batadv_is_my_mac(bat_priv, ethhdr->h_source))
 		goto free_skb;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/bat_v_elp.h
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/bat_v_elp.h
@@ -10,7 +10,6 @@
 #include "main.h"
 
 #include <linux/skbuff.h>
-#include <linux/workqueue.h>
 
 int batadv_v_elp_iface_enable(struct batadv_hard_iface *hard_iface);
 void batadv_v_elp_iface_disable(struct batadv_hard_iface *hard_iface);
@@ -19,6 +18,5 @@
 void batadv_v_elp_primary_iface_set(struct batadv_hard_iface *primary_iface);
 int batadv_v_elp_packet_recv(struct sk_buff *skb,
 			     struct batadv_hard_iface *if_incoming);
-void batadv_v_elp_throughput_metric_update(struct work_struct *work);
 
 #endif /* _NET_BATMAN_ADV_BAT_V_ELP_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/bat_v_ogm.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/bat_v_ogm.c
@@ -124,8 +124,10 @@
 {
 	struct batadv_priv *bat_priv = netdev_priv(hard_iface->soft_iface);
 
-	if (hard_iface->if_status != BATADV_IF_ACTIVE)
+	if (hard_iface->if_status != BATADV_IF_ACTIVE) {
+		kfree_skb(skb);
 		return;
+	}
 
 	batadv_inc_counter(bat_priv, BATADV_CNT_MGMT_TX);
 	batadv_add_counter(bat_priv, BATADV_CNT_MGMT_TX_BYTES,
@@ -838,8 +840,7 @@
 	/* check if there is enough space for the optional TVLV */
 	next_buff_pos += ntohs(ogm2_packet->tvlv_len);
 
-	return (next_buff_pos <= packet_len) &&
-	       (next_buff_pos <= BATADV_MAX_AGGREGATION_BYTES);
+	return next_buff_pos <= packet_len;
 }
 
 /**
@@ -986,7 +987,7 @@
 {
 	struct batadv_priv *bat_priv = netdev_priv(if_incoming->soft_iface);
 	struct batadv_ogm2_packet *ogm_packet;
-	struct ethhdr *ethhdr = eth_hdr(skb);
+	struct ethhdr *ethhdr;
 	int ogm_offset;
 	u8 *packet_pos;
 	int ret = NET_RX_DROP;
@@ -1000,6 +1001,7 @@
 	if (!batadv_check_management_packet(skb, if_incoming, BATADV_OGM2_HLEN))
 		goto free_skb;
 
+	ethhdr = eth_hdr(skb);
 	if (batadv_is_my_mac(bat_priv, ethhdr->h_source))
 		goto free_skb;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/distributed-arp-table.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/distributed-arp-table.c
@@ -101,7 +101,6 @@
  */
 static void batadv_dat_start_timer(struct batadv_priv *bat_priv)
 {
-	INIT_DELAYED_WORK(&bat_priv->dat.work, batadv_dat_purge);
 	queue_delayed_work(batadv_event_workqueue, &bat_priv->dat.work,
 			   msecs_to_jiffies(10000));
 }
@@ -819,6 +818,7 @@
 	if (!bat_priv->dat.hash)
 		return -ENOMEM;
 
+	INIT_DELAYED_WORK(&bat_priv->dat.work, batadv_dat_purge);
 	batadv_dat_start_timer(bat_priv);
 
 	batadv_tvlv_handler_register(bat_priv, batadv_dat_tvlv_ogm_handler_v1,
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/fragmentation.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/fragmentation.c
@@ -475,6 +475,17 @@
 		goto free_skb;
 	}
 
+	/* GRO might have added fragments to the fragment list instead of
+	 * frags[]. But this is not handled by skb_split and must be
+	 * linearized to avoid incorrect length information after all
+	 * batman-adv fragments were created and submitted to the
+	 * hard-interface
+	 */
+	if (skb_has_frag_list(skb) && __skb_linearize(skb)) {
+		ret = -ENOMEM;
+		goto free_skb;
+	}
+
 	/* Create one header to be copied to all fragments */
 	frag_header.packet_type = BATADV_UNICAST_FRAG;
 	frag_header.version = BATADV_COMPAT_VERSION;
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/hard-interface.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/hard-interface.c
@@ -149,22 +149,25 @@
 	struct net *net = dev_net(net_dev);
 	struct net_device *parent_dev;
 	struct net *parent_net;
+	int iflink;
 	bool ret;
 
 	/* check if this is a batman-adv mesh interface */
 	if (batadv_softif_is_valid(net_dev))
 		return true;
 
-	/* no more parents..stop recursion */
-	if (dev_get_iflink(net_dev) == 0 ||
-	    dev_get_iflink(net_dev) == net_dev->ifindex)
+	iflink = dev_get_iflink(net_dev);
+	if (iflink == 0)
 		return false;
 
 	parent_net = batadv_getlink_net(net_dev, net);
 
+	/* iflink to itself, most likely physical device */
+	if (net == parent_net && iflink == net_dev->ifindex)
+		return false;
+
 	/* recurse over the parent device */
-	parent_dev = __dev_get_by_index((struct net *)parent_net,
-					dev_get_iflink(net_dev));
+	parent_dev = __dev_get_by_index((struct net *)parent_net, iflink);
 	/* if we got a NULL parent_dev there is something broken.. */
 	if (!parent_dev) {
 		pr_err("Cannot find parent device\n");
@@ -214,14 +217,15 @@
 	struct net_device *real_netdev = NULL;
 	struct net *real_net;
 	struct net *net;
-	int ifindex;
+	int iflink;
 
 	ASSERT_RTNL();
 
 	if (!netdev)
 		return NULL;
 
-	if (netdev->ifindex == dev_get_iflink(netdev)) {
+	iflink = dev_get_iflink(netdev);
+	if (iflink == 0) {
 		dev_hold(netdev);
 		return netdev;
 	}
@@ -231,9 +235,16 @@
 		goto out;
 
 	net = dev_net(hard_iface->soft_iface);
-	ifindex = dev_get_iflink(netdev);
 	real_net = batadv_getlink_net(netdev, net);
-	real_netdev = dev_get_by_index(real_net, ifindex);
+
+	/* iflink to itself, most likely physical device */
+	if (net == real_net && netdev->ifindex == iflink) {
+		real_netdev = netdev;
+		dev_hold(real_netdev);
+		goto out;
+	}
+
+	real_netdev = dev_get_by_index(real_net, iflink);
 
 out:
 	batadv_hardif_put(hard_iface);
@@ -616,7 +627,19 @@
  */
 void batadv_update_min_mtu(struct net_device *soft_iface)
 {
-	soft_iface->mtu = batadv_hardif_min_mtu(soft_iface);
+	struct batadv_priv *bat_priv = netdev_priv(soft_iface);
+	int limit_mtu;
+	int mtu;
+
+	mtu = batadv_hardif_min_mtu(soft_iface);
+
+	if (bat_priv->mtu_set_by_user)
+		limit_mtu = bat_priv->mtu_set_by_user;
+	else
+		limit_mtu = ETH_DATA_LEN;
+
+	mtu = min(mtu, limit_mtu);
+	dev_set_mtu(soft_iface, mtu);
 
 	/* Check if the local translate table should be cleaned up to match a
 	 * new (and smaller) MTU.
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/multicast.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/multicast.c
@@ -134,7 +134,7 @@
 {
 	struct inet6_dev *in6_dev = __in6_dev_get(dev);
 
-	if (in6_dev && in6_dev->cnf.mc_forwarding)
+	if (in6_dev && atomic_read(&in6_dev->cnf.mc_forwarding))
 		return BATADV_NO_FLAGS;
 	else
 		return BATADV_MCAST_WANT_NO_RTR6;
@@ -1339,6 +1339,7 @@
  * @bat_priv: the bat priv with all the soft interface information
  * @skb: The multicast packet to check
  * @orig: an originator to be set to forward the skb to
+ * @is_routable: stores whether the destination is routable
  *
  * Return: the forwarding mode as enum batadv_forw_mode and in case of
  * BATADV_FORW_SINGLE set the orig to the single originator the skb
@@ -1346,17 +1347,16 @@
  */
 enum batadv_forw_mode
 batadv_mcast_forw_mode(struct batadv_priv *bat_priv, struct sk_buff *skb,
-		       struct batadv_orig_node **orig)
+		       struct batadv_orig_node **orig, int *is_routable)
 {
 	int ret, tt_count, ip_count, unsnoop_count, total_count;
 	bool is_unsnoopable = false;
 	unsigned int mcast_fanout;
 	struct ethhdr *ethhdr;
-	int is_routable = 0;
 	int rtr_count = 0;
 
 	ret = batadv_mcast_forw_mode_check(bat_priv, skb, &is_unsnoopable,
-					   &is_routable);
+					   is_routable);
 	if (ret == -ENOMEM)
 		return BATADV_FORW_NONE;
 	else if (ret < 0)
@@ -1369,7 +1369,7 @@
 	ip_count = batadv_mcast_forw_want_all_ip_count(bat_priv, ethhdr);
 	unsnoop_count = !is_unsnoopable ? 0 :
 			atomic_read(&bat_priv->mcast.num_want_all_unsnoopables);
-	rtr_count = batadv_mcast_forw_rtr_count(bat_priv, is_routable);
+	rtr_count = batadv_mcast_forw_rtr_count(bat_priv, *is_routable);
 
 	total_count = tt_count + ip_count + unsnoop_count + rtr_count;
 
@@ -1689,6 +1689,7 @@
  * @bat_priv: the bat priv with all the soft interface information
  * @skb: the multicast packet to transmit
  * @vid: the vlan identifier
+ * @is_routable: stores whether the destination is routable
  *
  * Sends copies of a frame with multicast destination to any node that signaled
  * interest in it, that is either via the translation table or the according
@@ -1701,7 +1702,7 @@
  * is neither IPv4 nor IPv6. NET_XMIT_SUCCESS otherwise.
  */
 int batadv_mcast_forw_send(struct batadv_priv *bat_priv, struct sk_buff *skb,
-			   unsigned short vid)
+			   unsigned short vid, int is_routable)
 {
 	int ret;
 
@@ -1717,12 +1718,16 @@
 		return ret;
 	}
 
+	if (!is_routable)
+		goto skip_mc_router;
+
 	ret = batadv_mcast_forw_want_rtr(bat_priv, skb, vid);
 	if (ret != NET_XMIT_SUCCESS) {
 		kfree_skb(skb);
 		return ret;
 	}
 
+skip_mc_router:
 	consume_skb(skb);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/multicast.h
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/multicast.h
@@ -43,7 +43,8 @@
 
 enum batadv_forw_mode
 batadv_mcast_forw_mode(struct batadv_priv *bat_priv, struct sk_buff *skb,
-		       struct batadv_orig_node **mcast_single_orig);
+		       struct batadv_orig_node **mcast_single_orig,
+		       int *is_routable);
 
 int batadv_mcast_forw_send_orig(struct batadv_priv *bat_priv,
 				struct sk_buff *skb,
@@ -51,7 +52,7 @@
 				struct batadv_orig_node *orig_node);
 
 int batadv_mcast_forw_send(struct batadv_priv *bat_priv, struct sk_buff *skb,
-			   unsigned short vid);
+			   unsigned short vid, int is_routable);
 
 void batadv_mcast_init(struct batadv_priv *bat_priv);
 
@@ -68,7 +69,8 @@
 
 static inline enum batadv_forw_mode
 batadv_mcast_forw_mode(struct batadv_priv *bat_priv, struct sk_buff *skb,
-		       struct batadv_orig_node **mcast_single_orig)
+		       struct batadv_orig_node **mcast_single_orig,
+		       int *is_routable)
 {
 	return BATADV_FORW_ALL;
 }
@@ -85,7 +87,7 @@
 
 static inline int
 batadv_mcast_forw_send(struct batadv_priv *bat_priv, struct sk_buff *skb,
-		       unsigned short vid)
+		       unsigned short vid, int is_routable)
 {
 	kfree_skb(skb);
 	return NET_XMIT_DROP;
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/netlink.c
@@ -495,7 +495,10 @@
 		attr = info->attrs[BATADV_ATTR_FRAGMENTATION_ENABLED];
 
 		atomic_set(&bat_priv->fragmentation, !!nla_get_u8(attr));
+
+		rtnl_lock();
 		batadv_update_min_mtu(bat_priv->soft_iface);
+		rtnl_unlock();
 	}
 
 	if (info->attrs[BATADV_ATTR_GW_BANDWIDTH_DOWN]) {
@@ -1368,21 +1371,21 @@
 	{
 		.cmd = BATADV_CMD_TP_METER,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.doit = batadv_netlink_tp_meter_start,
 		.internal_flags = BATADV_FLAG_NEED_MESH,
 	},
 	{
 		.cmd = BATADV_CMD_TP_METER_CANCEL,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.doit = batadv_netlink_tp_meter_cancel,
 		.internal_flags = BATADV_FLAG_NEED_MESH,
 	},
 	{
 		.cmd = BATADV_CMD_GET_ROUTING_ALGOS,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_algo_dump,
 	},
 	{
@@ -1397,68 +1400,68 @@
 	{
 		.cmd = BATADV_CMD_GET_TRANSTABLE_LOCAL,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_tt_local_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_TRANSTABLE_GLOBAL,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_tt_global_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_ORIGINATORS,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_orig_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_NEIGHBORS,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_hardif_neigh_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_GATEWAYS,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_gw_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_BLA_CLAIM,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_bla_claim_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_BLA_BACKBONE,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_bla_backbone_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_DAT_CACHE,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_dat_cache_dump,
 	},
 	{
 		.cmd = BATADV_CMD_GET_MCAST_FLAGS,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.dumpit = batadv_mcast_flags_dump,
 	},
 	{
 		.cmd = BATADV_CMD_SET_MESH,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.doit = batadv_netlink_set_mesh,
 		.internal_flags = BATADV_FLAG_NEED_MESH,
 	},
 	{
 		.cmd = BATADV_CMD_SET_HARDIF,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.doit = batadv_netlink_set_hardif,
 		.internal_flags = BATADV_FLAG_NEED_MESH |
 				  BATADV_FLAG_NEED_HARDIF,
@@ -1474,7 +1477,7 @@
 	{
 		.cmd = BATADV_CMD_SET_VLAN,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
-		.flags = GENL_ADMIN_PERM,
+		.flags = GENL_UNS_ADMIN_PERM,
 		.doit = batadv_netlink_set_vlan,
 		.internal_flags = BATADV_FLAG_NEED_MESH |
 				  BATADV_FLAG_NEED_VLAN,
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/originator.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/originator.c
@@ -11,6 +11,7 @@
 #include <linux/errno.h>
 #include <linux/etherdevice.h>
 #include <linux/gfp.h>
+#include <linux/if_vlan.h>
 #include <linux/jiffies.h>
 #include <linux/kernel.h>
 #include <linux/kref.h>
@@ -132,6 +133,29 @@
 }
 
 /**
+ * batadv_vlan_id_valid() - check if vlan id is in valid batman-adv encoding
+ * @vid: the VLAN identifier
+ *
+ * Return: true when either no vlan is set or if VLAN is in correct range,
+ *  false otherwise
+ */
+static bool batadv_vlan_id_valid(unsigned short vid)
+{
+	unsigned short non_vlan = vid & ~(BATADV_VLAN_HAS_TAG | VLAN_VID_MASK);
+
+	if (vid == 0)
+		return true;
+
+	if (!(vid & BATADV_VLAN_HAS_TAG))
+		return false;
+
+	if (non_vlan)
+		return false;
+
+	return true;
+}
+
+/**
  * batadv_orig_node_vlan_new() - search and possibly create an orig_node_vlan
  *  object
  * @orig_node: the originator serving the VLAN
@@ -149,6 +173,9 @@
 {
 	struct batadv_orig_node_vlan *vlan;
 
+	if (!batadv_vlan_id_valid(vid))
+		return NULL;
+
 	spin_lock_bh(&orig_node->vlan_list_lock);
 
 	/* first look if an object for this vid already exists */
@@ -1238,6 +1265,8 @@
 	/* for all origins... */
 	for (i = 0; i < hash->size; i++) {
 		head = &hash->table[i];
+		if (hlist_empty(head))
+			continue;
 		list_lock = &hash->list_locks[i];
 
 		spin_lock_bh(list_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/soft-interface.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/soft-interface.c
@@ -154,11 +154,14 @@
 
 static int batadv_interface_change_mtu(struct net_device *dev, int new_mtu)
 {
+	struct batadv_priv *bat_priv = netdev_priv(dev);
+
 	/* check ranges */
 	if (new_mtu < 68 || new_mtu > batadv_hardif_min_mtu(dev))
 		return -EINVAL;
 
 	dev->mtu = new_mtu;
+	bat_priv->mtu_set_by_user = new_mtu;
 
 	return 0;
 }
@@ -198,6 +201,7 @@
 	int gw_mode;
 	enum batadv_forw_mode forw_mode = BATADV_FORW_SINGLE;
 	struct batadv_orig_node *mcast_single_orig = NULL;
+	int mcast_is_routable = 0;
 	int network_offset = ETH_HLEN;
 	__be16 proto;
 
@@ -300,7 +304,8 @@
 send:
 		if (do_bcast && !is_broadcast_ether_addr(ethhdr->h_dest)) {
 			forw_mode = batadv_mcast_forw_mode(bat_priv, skb,
-							   &mcast_single_orig);
+							   &mcast_single_orig,
+							   &mcast_is_routable);
 			if (forw_mode == BATADV_FORW_NONE)
 				goto dropped;
 
@@ -359,7 +364,8 @@
 			ret = batadv_mcast_forw_send_orig(bat_priv, skb, vid,
 							  mcast_single_orig);
 		} else if (forw_mode == BATADV_FORW_SOME) {
-			ret = batadv_mcast_forw_send(bat_priv, skb, vid);
+			ret = batadv_mcast_forw_send(bat_priv, skb, vid,
+						     mcast_is_routable);
 		} else {
 			if (batadv_dat_snoop_outgoing_arp_request(bat_priv,
 								  skb))
@@ -438,7 +444,7 @@
 		if (!pskb_may_pull(skb, VLAN_ETH_HLEN))
 			goto dropped;
 
-		vhdr = (struct vlan_ethhdr *)skb->data;
+		vhdr = skb_vlan_eth_hdr(skb);
 
 		/* drop batman-in-batman packets to prevent loops */
 		if (vhdr->h_vlan_encapsulated_proto != htons(ETH_P_BATMAN))
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/translation-table.c
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/translation-table.c
@@ -774,7 +774,6 @@
 		if (roamed_back) {
 			batadv_tt_global_free(bat_priv, tt_global,
 					      "Roaming canceled");
-			tt_global = NULL;
 		} else {
 			/* The global entry has to be marked as ROAMING and
 			 * has to be kept for consistency purpose
@@ -991,16 +990,25 @@
 	int tt_diff_len, tt_change_len = 0;
 	int tt_diff_entries_num = 0;
 	int tt_diff_entries_count = 0;
+	bool drop_changes = false;
+	size_t tt_extra_len = 0;
 	u16 tvlv_len;
 
 	tt_diff_entries_num = atomic_read(&bat_priv->tt.local_changes);
 	tt_diff_len = batadv_tt_len(tt_diff_entries_num);
 
 	/* if we have too many changes for one packet don't send any
-	 * and wait for the tt table request which will be fragmented
+	 * and wait for the tt table request so we can reply with the full
+	 * (fragmented) table.
+	 *
+	 * The local change history should still be cleaned up so the next
+	 * TT round can start again with a clean state.
 	 */
-	if (tt_diff_len > bat_priv->soft_iface->mtu)
+	if (tt_diff_len > bat_priv->soft_iface->mtu) {
 		tt_diff_len = 0;
+		tt_diff_entries_num = 0;
+		drop_changes = true;
+	}
 
 	tvlv_len = batadv_tt_prepare_tvlv_local_data(bat_priv, &tt_data,
 						     &tt_change, &tt_diff_len);
@@ -1009,7 +1017,7 @@
 
 	tt_data->flags = BATADV_TT_OGM_DIFF;
 
-	if (tt_diff_len == 0)
+	if (!drop_changes && tt_diff_len == 0)
 		goto container_register;
 
 	spin_lock_bh(&bat_priv->tt.changes_list_lock);
@@ -1028,6 +1036,9 @@
 	}
 	spin_unlock_bh(&bat_priv->tt.changes_list_lock);
 
+	tt_extra_len = batadv_tt_len(tt_diff_entries_num -
+				     tt_diff_entries_count);
+
 	/* Keep the buffer for possible tt_request */
 	spin_lock_bh(&bat_priv->tt.last_changeset_lock);
 	kfree(bat_priv->tt.last_changeset);
@@ -1036,6 +1047,7 @@
 	tt_change_len = batadv_tt_len(tt_diff_entries_count);
 	/* check whether this new OGM has no changes due to size problems */
 	if (tt_diff_entries_count > 0) {
+		tt_diff_len -= tt_extra_len;
 		/* if kmalloc() fails we will reply with the full table
 		 * instead of providing the diff
 		 */
@@ -1048,6 +1060,8 @@
 	}
 	spin_unlock_bh(&bat_priv->tt.last_changeset_lock);
 
+	/* Remove extra packet space for OGM */
+	tvlv_len -= tt_extra_len;
 container_register:
 	batadv_tvlv_container_register(bat_priv, BATADV_TVLV_TT, 1, tt_data,
 				       tvlv_len);
@@ -2748,14 +2762,16 @@
  *
  * Fills the tvlv buff with the tt entries from the specified hash. If valid_cb
  * is not provided then this becomes a no-op.
+ *
+ * Return: Remaining unused length in tvlv_buff.
  */
-static void batadv_tt_tvlv_generate(struct batadv_priv *bat_priv,
-				    struct batadv_hashtable *hash,
-				    void *tvlv_buff, u16 tt_len,
-				    bool (*valid_cb)(const void *,
-						     const void *,
-						     u8 *flags),
-				    void *cb_data)
+static u16 batadv_tt_tvlv_generate(struct batadv_priv *bat_priv,
+				   struct batadv_hashtable *hash,
+				   void *tvlv_buff, u16 tt_len,
+				   bool (*valid_cb)(const void *,
+						    const void *,
+						    u8 *flags),
+				   void *cb_data)
 {
 	struct batadv_tt_common_entry *tt_common_entry;
 	struct batadv_tvlv_tt_change *tt_change;
@@ -2769,7 +2785,7 @@
 	tt_change = (struct batadv_tvlv_tt_change *)tvlv_buff;
 
 	if (!valid_cb)
-		return;
+		return tt_len;
 
 	rcu_read_lock();
 	for (i = 0; i < hash->size; i++) {
@@ -2795,6 +2811,8 @@
 		}
 	}
 	rcu_read_unlock();
+
+	return batadv_tt_len(tt_tot - tt_num_entries);
 }
 
 /**
@@ -3070,10 +3088,11 @@
 			goto out;
 
 		/* fill the rest of the tvlv with the real TT entries */
-		batadv_tt_tvlv_generate(bat_priv, bat_priv->tt.global_hash,
-					tt_change, tt_len,
-					batadv_tt_global_valid,
-					req_dst_orig_node);
+		tvlv_len -= batadv_tt_tvlv_generate(bat_priv,
+						    bat_priv->tt.global_hash,
+						    tt_change, tt_len,
+						    batadv_tt_global_valid,
+						    req_dst_orig_node);
 	}
 
 	/* Don't send the response, if larger than fragmented packet. */
@@ -3197,9 +3216,11 @@
 			goto out;
 
 		/* fill the rest of the tvlv with the real TT entries */
-		batadv_tt_tvlv_generate(bat_priv, bat_priv->tt.local_hash,
-					tt_change, tt_len,
-					batadv_tt_local_valid, NULL);
+		tvlv_len -= batadv_tt_tvlv_generate(bat_priv,
+						    bat_priv->tt.local_hash,
+						    tt_change, tt_len,
+						    batadv_tt_local_valid,
+						    NULL);
 	}
 
 	tvlv_tt_data->flags = BATADV_TT_RESPONSE;
@@ -3949,7 +3970,7 @@
 
 	spin_lock_bh(&bat_priv->tt.commit_lock);
 
-	while (true) {
+	while (timeout) {
 		table_size = batadv_tt_local_table_transmit_size(bat_priv);
 		if (packet_size_max >= table_size)
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/net/batman-adv/types.h
+++ linux-xilinx-zynqmp-5.15.0/net/batman-adv/types.h
@@ -596,9 +596,6 @@
 	 *  neighbor
 	 */
 	unsigned long last_unicast_tx;
-
-	/** @metric_work: work queue callback item for metric update */
-	struct work_struct metric_work;
 };
 
 /**
@@ -1547,6 +1544,12 @@
 	struct net_device *soft_iface;
 
 	/**
+	 * @mtu_set_by_user: MTU was set once by user
+	 * protected by rtnl_lock
+	 */
+	int mtu_set_by_user;
+
+	/**
 	 * @bat_counters: mesh internal traffic statistic counters (see
 	 *  batadv_counters)
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/6lowpan.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/6lowpan.c
@@ -824,11 +824,16 @@
 					 unsigned long hdr_len,
 					 unsigned long len, int nb)
 {
+	struct sk_buff *skb;
+
 	/* Note that we must allocate using GFP_ATOMIC here as
 	 * this function is called originally from netdev hard xmit
 	 * function in atomic context.
 	 */
-	return bt_skb_alloc(hdr_len + len, GFP_ATOMIC);
+	skb = bt_skb_alloc(hdr_len + len, GFP_ATOMIC);
+	if (!skb)
+		return ERR_PTR(-ENOMEM);
+	return skb;
 }
 
 static void chan_suspend_cb(struct l2cap_chan *chan)
@@ -971,6 +976,7 @@
 	hci_dev_lock(hdev);
 	hcon = hci_conn_hash_lookup_le(hdev, addr, *addr_type);
 	hci_dev_unlock(hdev);
+	hci_dev_put(hdev);
 
 	if (!hcon)
 		return -ENOENT;
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/af_bluetooth.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/af_bluetooth.c
@@ -266,7 +266,7 @@
 	skb = skb_recv_datagram(sk, flags, noblock, &err);
 	if (!skb) {
 		if (sk->sk_shutdown & RCV_SHUTDOWN)
-			return 0;
+			err = 0;
 
 		return err;
 	}
@@ -515,10 +515,11 @@
 		if (sk->sk_state == BT_LISTEN)
 			return -EINVAL;
 
-		lock_sock(sk);
+		spin_lock(&sk->sk_receive_queue.lock);
 		skb = skb_peek(&sk->sk_receive_queue);
 		amount = skb ? skb->len : 0;
-		release_sock(sk);
+		spin_unlock(&sk->sk_receive_queue.lock);
+
 		err = put_user(amount, (int __user *)arg);
 		break;
 
@@ -736,7 +737,7 @@
 
 	err = bt_sysfs_init();
 	if (err < 0)
-		return err;
+		goto cleanup_led;
 
 	err = sock_register(&bt_sock_family_ops);
 	if (err)
@@ -772,6 +773,9 @@
 	sock_unregister(PF_BLUETOOTH);
 cleanup_sysfs:
 	bt_sysfs_cleanup();
+cleanup_led:
+	bt_leds_cleanup();
+	debugfs_remove_recursive(bt_debugfs);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/bnep/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/bnep/core.c
@@ -385,7 +385,8 @@
 
 	case BNEP_COMPRESSED_DST_ONLY:
 		__skb_put_data(nskb, skb_mac_header(skb), ETH_ALEN);
-		__skb_put_data(nskb, s->eh.h_source, ETH_ALEN + 2);
+		__skb_put_data(nskb, s->eh.h_source, ETH_ALEN);
+		put_unaligned(s->eh.h_proto, (__be16 *)__skb_put(nskb, 2));
 		break;
 
 	case BNEP_GENERAL:
@@ -535,7 +536,7 @@
 
 	up_write(&bnep_session_sem);
 	free_netdev(dev);
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 	return 0;
 }
 
@@ -744,8 +745,7 @@
 	if (flt[0])
 		BT_INFO("BNEP filters: %s", flt);
 
-	bnep_sock_init();
-	return 0;
+	return bnep_sock_init();
 }
 
 static void __exit bnep_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/cmtp/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/cmtp/core.c
@@ -323,7 +323,7 @@
 	up_write(&cmtp_session_sem);
 
 	kfree(session);
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 	return 0;
 }
 
@@ -501,9 +501,7 @@
 {
 	BT_INFO("CMTP (CAPI Emulation) ver %s", VERSION);
 
-	cmtp_init_sockets();
-
-	return 0;
+	return cmtp_init_sockets();
 }
 
 static void __exit cmtp_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_conn.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_conn.c
@@ -135,13 +135,11 @@
 			hdev->notify(hdev, HCI_NOTIFY_CONN_DEL);
 	}
 
-	hci_conn_del_sysfs(conn);
-
 	debugfs_remove_recursive(conn->debugfs);
 
-	hci_dev_put(hdev);
+	hci_conn_del_sysfs(conn);
 
-	hci_conn_put(conn);
+	hci_dev_put(hdev);
 }
 
 static void le_scan_cleanup(struct work_struct *work)
@@ -541,7 +539,9 @@
 	if (conn->role == HCI_ROLE_SLAVE) {
 		/* Disable LE Advertising */
 		le_disable_advertising(hdev);
+		hci_dev_lock(hdev);
 		hci_le_conn_failed(conn, HCI_ERROR_ADVERTISING_TIMEOUT);
+		hci_dev_unlock(hdev);
 		return;
 	}
 
@@ -553,11 +553,32 @@
 {
 	struct hci_conn *conn;
 
+	switch (type) {
+	case ACL_LINK:
+		if (!hdev->acl_mtu)
+			return ERR_PTR(-ECONNREFUSED);
+		break;
+	case LE_LINK:
+		if (hdev->le_mtu && hdev->le_mtu < HCI_MIN_LE_MTU)
+			return ERR_PTR(-ECONNREFUSED);
+		if (!hdev->le_mtu && hdev->acl_mtu < HCI_MIN_LE_MTU)
+			return ERR_PTR(-ECONNREFUSED);
+		break;
+	case SCO_LINK:
+	case ESCO_LINK:
+		if (!hdev->sco_pkts)
+			/* Controller does not support SCO or eSCO over HCI */
+			return ERR_PTR(-ECONNREFUSED);
+		break;
+	default:
+		return ERR_PTR(-ECONNREFUSED);
+	}
+
 	BT_DBG("%s dst %pMR", hdev->name, dst);
 
 	conn = kzalloc(sizeof(*conn), GFP_KERNEL);
 	if (!conn)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	bacpy(&conn->dst, dst);
 	bacpy(&conn->src, &hdev->bdaddr);
@@ -586,10 +607,12 @@
 	switch (type) {
 	case ACL_LINK:
 		conn->pkt_type = hdev->pkt_type & ACL_PTYPE_MASK;
+		conn->mtu = hdev->acl_mtu;
 		break;
 	case LE_LINK:
 		/* conn->src should reflect the local identity address */
 		hci_copy_identity_address(hdev, &conn->src, &conn->src_type);
+		conn->mtu = hdev->le_mtu ? hdev->le_mtu : hdev->acl_mtu;
 		break;
 	case SCO_LINK:
 		if (lmp_esco_capable(hdev))
@@ -597,9 +620,12 @@
 					(hdev->esco_type & EDR_ESCO_MASK);
 		else
 			conn->pkt_type = hdev->pkt_type & SCO_PTYPE_MASK;
+
+		conn->mtu = hdev->sco_mtu;
 		break;
 	case ESCO_LINK:
 		conn->pkt_type = hdev->esco_type & ~EDR_ESCO_MASK;
+		conn->mtu = hdev->sco_mtu;
 		break;
 	}
 
@@ -1097,8 +1123,8 @@
 		bacpy(&conn->dst, dst);
 	} else {
 		conn = hci_conn_add(hdev, LE_LINK, dst, role);
-		if (!conn)
-			return ERR_PTR(-ENOMEM);
+		if (IS_ERR(conn))
+			return conn;
 		hci_conn_hold(conn);
 		conn->pending_sec_level = sec_level;
 	}
@@ -1262,8 +1288,8 @@
 	BT_DBG("requesting refresh of dst_addr");
 
 	conn = hci_conn_add(hdev, LE_LINK, dst, HCI_ROLE_MASTER);
-	if (!conn)
-		return ERR_PTR(-ENOMEM);
+	if (IS_ERR(conn))
+		return conn;
 
 	if (hci_explicit_conn_params_set(hdev, dst, dst_type) < 0) {
 		hci_conn_del(conn);
@@ -1298,11 +1324,20 @@
 		return ERR_PTR(-EOPNOTSUPP);
 	}
 
+	/* Reject outgoing connection to device with same BD ADDR against
+	 * CVE-2020-26555
+	 */
+	if (!bacmp(&hdev->bdaddr, dst)) {
+		bt_dev_dbg(hdev, "Reject connection with same BD_ADDR %pMR\n",
+			   dst);
+		return ERR_PTR(-ECONNREFUSED);
+	}
+
 	acl = hci_conn_hash_lookup_ba(hdev, ACL_LINK, dst);
 	if (!acl) {
 		acl = hci_conn_add(hdev, ACL_LINK, dst, HCI_ROLE_MASTER);
-		if (!acl)
-			return ERR_PTR(-ENOMEM);
+		if (IS_ERR(acl))
+			return acl;
 	}
 
 	hci_conn_hold(acl);
@@ -1332,9 +1367,9 @@
 	sco = hci_conn_hash_lookup_ba(hdev, type, dst);
 	if (!sco) {
 		sco = hci_conn_add(hdev, type, dst, HCI_ROLE_MASTER);
-		if (!sco) {
+		if (IS_ERR(sco)) {
 			hci_conn_drop(acl);
-			return ERR_PTR(-ENOMEM);
+			return sco;
 		}
 	}
 
@@ -1427,12 +1462,10 @@
 		hci_send_cmd(conn->hdev, HCI_OP_AUTH_REQUESTED,
 			     sizeof(cp), &cp);
 
-		/* If we're already encrypted set the REAUTH_PEND flag,
-		 * otherwise set the ENCRYPT_PEND.
+		/* Set the ENCRYPT_PEND to trigger encryption after
+		 * authentication.
 		 */
-		if (test_bit(HCI_CONN_ENCRYPT, &conn->flags))
-			set_bit(HCI_CONN_REAUTH_PEND, &conn->flags);
-		else
+		if (!test_bit(HCI_CONN_ENCRYPT, &conn->flags))
 			set_bit(HCI_CONN_ENCRYPT_PEND, &conn->flags);
 	}
 
@@ -1475,34 +1508,41 @@
 	if (!test_bit(HCI_CONN_AUTH, &conn->flags))
 		goto auth;
 
-	/* An authenticated FIPS approved combination key has sufficient
-	 * security for security level 4. */
-	if (conn->key_type == HCI_LK_AUTH_COMBINATION_P256 &&
-	    sec_level == BT_SECURITY_FIPS)
-		goto encrypt;
-
-	/* An authenticated combination key has sufficient security for
-	   security level 3. */
-	if ((conn->key_type == HCI_LK_AUTH_COMBINATION_P192 ||
-	     conn->key_type == HCI_LK_AUTH_COMBINATION_P256) &&
-	    sec_level == BT_SECURITY_HIGH)
-		goto encrypt;
-
-	/* An unauthenticated combination key has sufficient security for
-	   security level 1 and 2. */
-	if ((conn->key_type == HCI_LK_UNAUTH_COMBINATION_P192 ||
-	     conn->key_type == HCI_LK_UNAUTH_COMBINATION_P256) &&
-	    (sec_level == BT_SECURITY_MEDIUM || sec_level == BT_SECURITY_LOW))
-		goto encrypt;
-
-	/* A combination key has always sufficient security for the security
-	   levels 1 or 2. High security level requires the combination key
-	   is generated using maximum PIN code length (16).
-	   For pre 2.1 units. */
-	if (conn->key_type == HCI_LK_COMBINATION &&
-	    (sec_level == BT_SECURITY_MEDIUM || sec_level == BT_SECURITY_LOW ||
-	     conn->pin_length == 16))
-		goto encrypt;
+	switch (conn->key_type) {
+	case HCI_LK_AUTH_COMBINATION_P256:
+		/* An authenticated FIPS approved combination key has
+		 * sufficient security for security level 4 or lower.
+		 */
+		if (sec_level <= BT_SECURITY_FIPS)
+			goto encrypt;
+		break;
+	case HCI_LK_AUTH_COMBINATION_P192:
+		/* An authenticated combination key has sufficient security for
+		 * security level 3 or lower.
+		 */
+		if (sec_level <= BT_SECURITY_HIGH)
+			goto encrypt;
+		break;
+	case HCI_LK_UNAUTH_COMBINATION_P192:
+	case HCI_LK_UNAUTH_COMBINATION_P256:
+		/* An unauthenticated combination key has sufficient security
+		 * for security level 2 or lower.
+		 */
+		if (sec_level <= BT_SECURITY_MEDIUM)
+			goto encrypt;
+		break;
+	case HCI_LK_COMBINATION:
+		/* A combination key has always sufficient security for the
+		 * security levels 2 or lower. High security level requires the
+		 * combination key is generated using maximum PIN code length
+		 * (16). For pre 2.1 units.
+		 */
+		if (sec_level <= BT_SECURITY_MEDIUM || conn->pin_length == 16)
+			goto encrypt;
+		break;
+	default:
+		break;
+	}
 
 auth:
 	if (test_bit(HCI_CONN_ENCRYPT_PEND, &conn->flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_core.c
@@ -742,7 +742,8 @@
 			hci_req_add(req, HCI_OP_LE_READ_ADV_TX_POWER, 0, NULL);
 		}
 
-		if (hdev->commands[38] & 0x80) {
+		if ((hdev->commands[38] & 0x80) &&
+		    !test_bit(HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, &hdev->quirks)) {
 			/* Read LE Min/Max Tx Power*/
 			hci_req_add(req, HCI_OP_LE_READ_TRANSMIT_POWER,
 				    0, NULL);
@@ -1631,6 +1632,7 @@
 			hdev->flush(hdev);
 
 		if (hdev->sent_cmd) {
+			cancel_delayed_work_sync(&hdev->cmd_timer);
 			kfree_skb(hdev->sent_cmd);
 			hdev->sent_cmd = NULL;
 		}
@@ -2185,7 +2187,7 @@
 	else
 		flags = hdev->flags;
 
-	strcpy(di.name, hdev->name);
+	strscpy(di.name, hdev->name, sizeof(di.name));
 	di.bdaddr   = hdev->bdaddr;
 	di.type     = (hdev->bus & 0x0f) | ((hdev->dev_type & 0x03) << 4);
 	di.flags    = flags;
@@ -2328,6 +2330,7 @@
 {
 	struct hci_dev *hdev = container_of(work, struct hci_dev, error_reset);
 
+	hci_dev_hold(hdev);
 	BT_DBG("%s", hdev->name);
 
 	if (hdev->hw_error)
@@ -2335,10 +2338,10 @@
 	else
 		bt_dev_err(hdev, "hardware error 0x%2.2x", hdev->hw_error_code);
 
-	if (hci_dev_do_close(hdev))
-		return;
+	if (!hci_dev_do_close(hdev))
+		hci_dev_do_open(hdev);
 
-	hci_dev_do_open(hdev);
+	hci_dev_put(hdev);
 }
 
 void hci_uuids_clear(struct hci_dev *hdev)
@@ -2353,9 +2356,9 @@
 
 void hci_link_keys_clear(struct hci_dev *hdev)
 {
-	struct link_key *key;
+	struct link_key *key, *tmp;
 
-	list_for_each_entry(key, &hdev->link_keys, list) {
+	list_for_each_entry_safe(key, tmp, &hdev->link_keys, list) {
 		list_del_rcu(&key->list);
 		kfree_rcu(key, rcu);
 	}
@@ -2363,9 +2366,9 @@
 
 void hci_smp_ltks_clear(struct hci_dev *hdev)
 {
-	struct smp_ltk *k;
+	struct smp_ltk *k, *tmp;
 
-	list_for_each_entry(k, &hdev->long_term_keys, list) {
+	list_for_each_entry_safe(k, tmp, &hdev->long_term_keys, list) {
 		list_del_rcu(&k->list);
 		kfree_rcu(k, rcu);
 	}
@@ -2373,9 +2376,9 @@
 
 void hci_smp_irks_clear(struct hci_dev *hdev)
 {
-	struct smp_irk *k;
+	struct smp_irk *k, *tmp;
 
-	list_for_each_entry(k, &hdev->identity_resolving_keys, list) {
+	list_for_each_entry_safe(k, tmp, &hdev->identity_resolving_keys, list) {
 		list_del_rcu(&k->list);
 		kfree_rcu(k, rcu);
 	}
@@ -2383,9 +2386,9 @@
 
 void hci_blocked_keys_clear(struct hci_dev *hdev)
 {
-	struct blocked_key *b;
+	struct blocked_key *b, *tmp;
 
-	list_for_each_entry(b, &hdev->blocked_keys, list) {
+	list_for_each_entry_safe(b, tmp, &hdev->blocked_keys, list) {
 		list_del_rcu(&b->list);
 		kfree_rcu(b, rcu);
 	}
@@ -2695,10 +2698,10 @@
 
 int hci_remove_ltk(struct hci_dev *hdev, bdaddr_t *bdaddr, u8 bdaddr_type)
 {
-	struct smp_ltk *k;
+	struct smp_ltk *k, *tmp;
 	int removed = 0;
 
-	list_for_each_entry_rcu(k, &hdev->long_term_keys, list) {
+	list_for_each_entry_safe(k, tmp, &hdev->long_term_keys, list) {
 		if (bacmp(bdaddr, &k->bdaddr) || k->bdaddr_type != bdaddr_type)
 			continue;
 
@@ -2714,9 +2717,9 @@
 
 void hci_remove_irk(struct hci_dev *hdev, bdaddr_t *bdaddr, u8 addr_type)
 {
-	struct smp_irk *k;
+	struct smp_irk *k, *tmp;
 
-	list_for_each_entry_rcu(k, &hdev->identity_resolving_keys, list) {
+	list_for_each_entry_safe(k, tmp, &hdev->identity_resolving_keys, list) {
 		if (bacmp(bdaddr, &k->bdaddr) || k->addr_type != addr_type)
 			continue;
 
@@ -3906,10 +3909,10 @@
 	 */
 	switch (hdev->dev_type) {
 	case HCI_PRIMARY:
-		id = ida_simple_get(&hci_index_ida, 0, 0, GFP_KERNEL);
+		id = ida_simple_get(&hci_index_ida, 0, HCI_MAX_ID, GFP_KERNEL);
 		break;
 	case HCI_AMP:
-		id = ida_simple_get(&hci_index_ida, 1, 0, GFP_KERNEL);
+		id = ida_simple_get(&hci_index_ida, 1, HCI_MAX_ID, GFP_KERNEL);
 		break;
 	default:
 		return -EINVAL;
@@ -3918,7 +3921,11 @@
 	if (id < 0)
 		return id;
 
-	sprintf(hdev->name, "hci%d", id);
+	error = dev_set_name(&hdev->dev, "hci%u", id);
+	if (error)
+		return error;
+
+	hdev->name = dev_name(&hdev->dev);
 	hdev->id = id;
 
 	BT_DBG("%p name %s bus %d", hdev, hdev->name, hdev->bus);
@@ -3940,8 +3947,6 @@
 	if (!IS_ERR_OR_NULL(bt_debugfs))
 		hdev->debugfs = debugfs_create_dir(hdev->name, bt_debugfs);
 
-	dev_set_name(&hdev->dev, "%s", hdev->name);
-
 	error = device_add(&hdev->dev);
 	if (error < 0)
 		goto err_wqueue;
@@ -3984,7 +3989,8 @@
 	hci_sock_dev_event(hdev, HCI_DEV_REG);
 	hci_dev_hold(hdev);
 
-	if (!test_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks)) {
+	if (!hdev->suspend_notifier.notifier_call &&
+	    !test_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks)) {
 		hdev->suspend_notifier.notifier_call = hci_suspend_notifier;
 		error = register_pm_notifier(&hdev->suspend_notifier);
 		if (error)
@@ -3998,6 +4004,7 @@
 	return id;
 
 err_wqueue:
+	debugfs_remove_recursive(hdev->debugfs);
 	destroy_workqueue(hdev->workqueue);
 	destroy_workqueue(hdev->req_workqueue);
 err:
@@ -4018,7 +4025,11 @@
 	list_del(&hdev->list);
 	write_unlock(&hci_dev_list_lock);
 
+	cancel_work_sync(&hdev->rx_work);
+	cancel_work_sync(&hdev->cmd_work);
+	cancel_work_sync(&hdev->tx_work);
 	cancel_work_sync(&hdev->power_on);
+	cancel_work_sync(&hdev->error_reset);
 
 	if (!test_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks)) {
 		hci_suspend_clear_tasks(hdev);
@@ -4081,6 +4092,7 @@
 	hci_dev_unlock(hdev);
 
 	ida_simple_remove(&hci_index_ida, hdev->id);
+	kfree_skb(hdev->sent_cmd);
 	kfree(hdev);
 }
 EXPORT_SYMBOL(hci_release_dev);
@@ -4670,15 +4682,27 @@
 	return DIV_ROUND_UP(skb->len - HCI_ACL_HDR_SIZE, hdev->block_len);
 }
 
-static void __check_timeout(struct hci_dev *hdev, unsigned int cnt)
+static void __check_timeout(struct hci_dev *hdev, unsigned int cnt, u8 type)
 {
-	if (!hci_dev_test_flag(hdev, HCI_UNCONFIGURED)) {
-		/* ACL tx timeout must be longer than maximum
-		 * link supervision timeout (40.9 seconds) */
-		if (!cnt && time_after(jiffies, hdev->acl_last_tx +
-				       HCI_ACL_TX_TIMEOUT))
-			hci_link_tx_to(hdev, ACL_LINK);
+	unsigned long last_tx;
+
+	if (hci_dev_test_flag(hdev, HCI_UNCONFIGURED))
+		return;
+
+	switch (type) {
+	case LE_LINK:
+		last_tx = hdev->le_last_tx;
+		break;
+	default:
+		last_tx = hdev->acl_last_tx;
+		break;
 	}
+
+	/* tx timeout must be longer than maximum link supervision timeout
+	 * (40.9 seconds)
+	 */
+	if (!cnt && time_after(jiffies, last_tx + HCI_ACL_TX_TIMEOUT))
+		hci_link_tx_to(hdev, type);
 }
 
 /* Schedule SCO */
@@ -4736,7 +4760,7 @@
 	struct sk_buff *skb;
 	int quote;
 
-	__check_timeout(hdev, cnt);
+	__check_timeout(hdev, cnt, ACL_LINK);
 
 	while (hdev->acl_cnt &&
 	       (chan = hci_chan_sent(hdev, ACL_LINK, &quote))) {
@@ -4779,8 +4803,6 @@
 	int quote;
 	u8 type;
 
-	__check_timeout(hdev, cnt);
-
 	BT_DBG("%s", hdev->name);
 
 	if (hdev->dev_type == HCI_AMP)
@@ -4788,6 +4810,8 @@
 	else
 		type = ACL_LINK;
 
+	__check_timeout(hdev, cnt, type);
+
 	while (hdev->block_cnt > 0 &&
 	       (chan = hci_chan_sent(hdev, type, &quote))) {
 		u32 priority = (skb_peek(&chan->data_q))->priority;
@@ -4852,19 +4876,19 @@
 {
 	struct hci_chan *chan;
 	struct sk_buff *skb;
-	int quote, cnt, tmp;
+	int quote, *cnt, tmp;
 
 	BT_DBG("%s", hdev->name);
 
 	if (!hci_conn_num(hdev, LE_LINK))
 		return;
 
-	cnt = hdev->le_pkts ? hdev->le_cnt : hdev->acl_cnt;
+	cnt = hdev->le_pkts ? &hdev->le_cnt : &hdev->acl_cnt;
 
-	__check_timeout(hdev, cnt);
+	__check_timeout(hdev, *cnt, LE_LINK);
 
-	tmp = cnt;
-	while (cnt && (chan = hci_chan_sent(hdev, LE_LINK, &quote))) {
+	tmp = *cnt;
+	while (*cnt && (chan = hci_chan_sent(hdev, LE_LINK, &quote))) {
 		u32 priority = (skb_peek(&chan->data_q))->priority;
 		while (quote-- && (skb = skb_peek(&chan->data_q))) {
 			BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
@@ -4879,7 +4903,7 @@
 			hci_send_frame(hdev, skb);
 			hdev->le_last_tx = jiffies;
 
-			cnt--;
+			(*cnt)--;
 			chan->sent++;
 			chan->conn->sent++;
 
@@ -4889,12 +4913,7 @@
 		}
 	}
 
-	if (hdev->le_pkts)
-		hdev->le_cnt = cnt;
-	else
-		hdev->acl_cnt = cnt;
-
-	if (cnt != tmp)
+	if (*cnt != tmp)
 		hci_prio_recalculate(hdev, LE_LINK);
 }
 
@@ -4924,18 +4943,22 @@
 /* ACL data packet */
 static void hci_acldata_packet(struct hci_dev *hdev, struct sk_buff *skb)
 {
-	struct hci_acl_hdr *hdr = (void *) skb->data;
+	struct hci_acl_hdr *hdr;
 	struct hci_conn *conn;
 	__u16 handle, flags;
 
-	skb_pull(skb, HCI_ACL_HDR_SIZE);
+	hdr = skb_pull_data(skb, sizeof(*hdr));
+	if (!hdr) {
+		bt_dev_err(hdev, "ACL packet too small");
+		goto drop;
+	}
 
 	handle = __le16_to_cpu(hdr->handle);
 	flags  = hci_flags(handle);
 	handle = hci_handle(handle);
 
-	BT_DBG("%s len %d handle 0x%4.4x flags 0x%4.4x", hdev->name, skb->len,
-	       handle, flags);
+	bt_dev_dbg(hdev, "len %d handle 0x%4.4x flags 0x%4.4x", skb->len,
+		   handle, flags);
 
 	hdev->stat.acl_rx++;
 
@@ -4954,6 +4977,7 @@
 			   handle);
 	}
 
+drop:
 	kfree_skb(skb);
 }
 
@@ -5085,7 +5109,7 @@
 			*req_complete_skb = bt_cb(skb)->hci.req_complete_skb;
 		else
 			*req_complete = bt_cb(skb)->hci.req_complete;
-		kfree_skb(skb);
+		dev_kfree_skb_irq(skb);
 	}
 	spin_unlock_irqrestore(&hdev->cmd_q.lock, flags);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_debugfs.c
@@ -216,10 +216,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val == 0 || val > hdev->conn_info_max_age)
+	hci_dev_lock(hdev);
+	if (val == 0 || val > hdev->conn_info_max_age) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->conn_info_min_age = val;
 	hci_dev_unlock(hdev);
 
@@ -244,10 +246,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val == 0 || val < hdev->conn_info_min_age)
+	hci_dev_lock(hdev);
+	if (val == 0 || val < hdev->conn_info_min_age) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->conn_info_max_age = val;
 	hci_dev_unlock(hdev);
 
@@ -565,10 +569,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val == 0 || val % 2 || val > hdev->sniff_max_interval)
+	hci_dev_lock(hdev);
+	if (val == 0 || val % 2 || val > hdev->sniff_max_interval) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->sniff_min_interval = val;
 	hci_dev_unlock(hdev);
 
@@ -593,10 +599,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val == 0 || val % 2 || val < hdev->sniff_min_interval)
+	hci_dev_lock(hdev);
+	if (val == 0 || val % 2 || val < hdev->sniff_min_interval) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->sniff_max_interval = val;
 	hci_dev_unlock(hdev);
 
@@ -848,10 +856,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val < 0x0006 || val > 0x0c80 || val > hdev->le_conn_max_interval)
+	hci_dev_lock(hdev);
+	if (val < 0x0006 || val > 0x0c80 || val > hdev->le_conn_max_interval) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->le_conn_min_interval = val;
 	hci_dev_unlock(hdev);
 
@@ -876,10 +886,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val < 0x0006 || val > 0x0c80 || val < hdev->le_conn_min_interval)
+	hci_dev_lock(hdev);
+	if (val < 0x0006 || val > 0x0c80 || val < hdev->le_conn_min_interval) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->le_conn_max_interval = val;
 	hci_dev_unlock(hdev);
 
@@ -988,10 +1000,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val < 0x0020 || val > 0x4000 || val > hdev->le_adv_max_interval)
+	hci_dev_lock(hdev);
+	if (val < 0x0020 || val > 0x4000 || val > hdev->le_adv_max_interval) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->le_adv_min_interval = val;
 	hci_dev_unlock(hdev);
 
@@ -1016,10 +1030,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val < 0x0020 || val > 0x4000 || val < hdev->le_adv_min_interval)
+	hci_dev_lock(hdev);
+	if (val < 0x0020 || val > 0x4000 || val < hdev->le_adv_min_interval) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->le_adv_max_interval = val;
 	hci_dev_unlock(hdev);
 
@@ -1044,10 +1060,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val > hdev->le_max_key_size || val < SMP_MIN_ENC_KEY_SIZE)
+	hci_dev_lock(hdev);
+	if (val > hdev->le_max_key_size || val < SMP_MIN_ENC_KEY_SIZE) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->le_min_key_size = val;
 	hci_dev_unlock(hdev);
 
@@ -1072,10 +1090,12 @@
 {
 	struct hci_dev *hdev = data;
 
-	if (val > SMP_MAX_ENC_KEY_SIZE || val < hdev->le_min_key_size)
+	hci_dev_lock(hdev);
+	if (val > SMP_MAX_ENC_KEY_SIZE || val < hdev->le_min_key_size) {
+		hci_dev_unlock(hdev);
 		return -EINVAL;
+	}
 
-	hci_dev_lock(hdev);
 	hdev->le_max_key_size = val;
 	hci_dev_unlock(hdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_event.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_event.c
@@ -25,6 +25,8 @@
 /* Bluetooth HCI event handling. */
 
 #include <asm/unaligned.h>
+#include <linux/crypto.h>
+#include <crypto/algapi.h>
 
 #include <net/bluetooth/bluetooth.h>
 #include <net/bluetooth/hci_core.h>
@@ -745,14 +747,14 @@
 	hdev->flow_ctl_mode = rp->mode;
 }
 
-static void hci_cc_read_buffer_size(struct hci_dev *hdev, struct sk_buff *skb)
+static u8 hci_cc_read_buffer_size(struct hci_dev *hdev, struct sk_buff *skb)
 {
 	struct hci_rp_read_buffer_size *rp = (void *) skb->data;
 
 	BT_DBG("%s status 0x%2.2x", hdev->name, rp->status);
 
 	if (rp->status)
-		return;
+		return rp->status;
 
 	hdev->acl_mtu  = __le16_to_cpu(rp->acl_mtu);
 	hdev->sco_mtu  = rp->sco_mtu;
@@ -769,6 +771,11 @@
 
 	BT_DBG("%s acl mtu %d:%d sco mtu %d:%d", hdev->name, hdev->acl_mtu,
 	       hdev->acl_pkts, hdev->sco_mtu, hdev->sco_pkts);
+
+	if (!hdev->acl_mtu || !hdev->acl_pkts)
+		return HCI_ERROR_INVALID_PARAMETERS;
+
+	return rp->status;
 }
 
 static void hci_cc_read_bd_addr(struct hci_dev *hdev, struct sk_buff *skb)
@@ -1033,15 +1040,15 @@
 	hci_dev_unlock(hdev);
 }
 
-static void hci_cc_le_read_buffer_size(struct hci_dev *hdev,
-				       struct sk_buff *skb)
+static u8 hci_cc_le_read_buffer_size(struct hci_dev *hdev,
+				     struct sk_buff *skb)
 {
 	struct hci_rp_le_read_buffer_size *rp = (void *) skb->data;
 
 	BT_DBG("%s status 0x%2.2x", hdev->name, rp->status);
 
 	if (rp->status)
-		return;
+		return rp->status;
 
 	hdev->le_mtu = __le16_to_cpu(rp->le_mtu);
 	hdev->le_pkts = rp->le_max_pkt;
@@ -1049,6 +1056,11 @@
 	hdev->le_cnt = hdev->le_pkts;
 
 	BT_DBG("%s le mtu %d:%d", hdev->name, hdev->le_mtu, hdev->le_pkts);
+
+	if (hdev->le_mtu && hdev->le_mtu < HCI_MIN_LE_MTU)
+		return HCI_ERROR_INVALID_PARAMETERS;
+
+	return rp->status;
 }
 
 static void hci_cc_le_read_local_features(struct hci_dev *hdev,
@@ -1325,8 +1337,10 @@
 					   &conn->le_conn_timeout,
 					   conn->conn_timeout);
 	} else {
-		if (adv) {
-			adv->enabled = false;
+		if (cp->num_of_sets) {
+			if (adv)
+				adv->enabled = false;
+
 			/* If just one instance was disabled check if there are
 			 * any other instance enabled before clearing HCI_LE_ADV
 			 */
@@ -1557,7 +1571,9 @@
 	if (status)
 		return;
 
+	hci_dev_lock(hdev);
 	hci_bdaddr_list_clear(&hdev->le_accept_list);
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cc_le_add_to_accept_list(struct hci_dev *hdev,
@@ -1575,8 +1591,10 @@
 	if (!sent)
 		return;
 
+	hci_dev_lock(hdev);
 	hci_bdaddr_list_add(&hdev->le_accept_list, &sent->bdaddr,
 			    sent->bdaddr_type);
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cc_le_del_from_accept_list(struct hci_dev *hdev,
@@ -1594,8 +1612,10 @@
 	if (!sent)
 		return;
 
+	hci_dev_lock(hdev);
 	hci_bdaddr_list_del(&hdev->le_accept_list, &sent->bdaddr,
 			    sent->bdaddr_type);
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cc_le_read_supported_states(struct hci_dev *hdev,
@@ -1659,9 +1679,11 @@
 	if (!sent)
 		return;
 
+	hci_dev_lock(hdev);
 	hci_bdaddr_list_add_with_irk(&hdev->le_resolv_list, &sent->bdaddr,
 				sent->bdaddr_type, sent->peer_irk,
 				sent->local_irk);
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cc_le_del_from_resolv_list(struct hci_dev *hdev,
@@ -1679,8 +1701,10 @@
 	if (!sent)
 		return;
 
+	hci_dev_lock(hdev);
 	hci_bdaddr_list_del_with_irk(&hdev->le_resolv_list, &sent->bdaddr,
 			    sent->bdaddr_type);
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cc_le_clear_resolv_list(struct hci_dev *hdev,
@@ -1693,7 +1717,9 @@
 	if (status)
 		return;
 
+	hci_dev_lock(hdev);
 	hci_bdaddr_list_clear(&hdev->le_resolv_list);
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cc_le_read_resolv_list_size(struct hci_dev *hdev,
@@ -1910,7 +1936,8 @@
 		return;
 	}
 
-	set_bit(HCI_INQUIRY, &hdev->flags);
+	if (hci_sent_cmd_data(hdev, HCI_OP_INQUIRY))
+		set_bit(HCI_INQUIRY, &hdev->flags);
 }
 
 static void hci_cs_create_conn(struct hci_dev *hdev, __u8 status)
@@ -1943,8 +1970,8 @@
 		if (!conn) {
 			conn = hci_conn_add(hdev, ACL_LINK, &cp->bdaddr,
 					    HCI_ROLE_MASTER);
-			if (!conn)
-				bt_dev_err(hdev, "no memory for new connection");
+			if (IS_ERR(conn))
+				bt_dev_err(hdev, "connection err: %ld", PTR_ERR(conn));
 		}
 	}
 
@@ -2671,8 +2698,8 @@
 						      BDADDR_BREDR)) {
 			conn = hci_conn_add(hdev, ev->link_type, &ev->bdaddr,
 					    HCI_ROLE_SLAVE);
-			if (!conn) {
-				bt_dev_err(hdev, "no memory for new conn");
+			if (IS_ERR(conn)) {
+				bt_dev_err(hdev, "connection err: %ld", PTR_ERR(conn));
 				goto unlock;
 			}
 		} else {
@@ -2712,6 +2739,31 @@
 		if (test_bit(HCI_ENCRYPT, &hdev->flags))
 			set_bit(HCI_CONN_ENCRYPT, &conn->flags);
 
+		/* "Link key request" completed ahead of "connect request" completes */
+		if (ev->encr_mode == 1 && !test_bit(HCI_CONN_ENCRYPT, &conn->flags) &&
+		    ev->link_type == ACL_LINK) {
+			struct link_key *key;
+			struct hci_cp_read_enc_key_size cp;
+
+			key = hci_find_link_key(hdev, &ev->bdaddr);
+			if (key) {
+				set_bit(HCI_CONN_ENCRYPT, &conn->flags);
+
+				if (!(hdev->commands[20] & 0x10)) {
+					conn->enc_key_size = HCI_LINK_KEY_SIZE;
+				} else {
+					cp.handle = cpu_to_le16(conn->handle);
+					if (hci_send_cmd(hdev, HCI_OP_READ_ENC_KEY_SIZE,
+							 sizeof(cp), &cp)) {
+						bt_dev_err(hdev, "sending read key size failed");
+						conn->enc_key_size = HCI_LINK_KEY_SIZE;
+					}
+				}
+
+				hci_encrypt_cfm(conn, ev->status);
+			}
+		}
+
 		/* Get remote features */
 		if (conn->type == ACL_LINK) {
 			struct hci_cp_read_remote_features cp;
@@ -2780,6 +2832,16 @@
 	BT_DBG("%s bdaddr %pMR type 0x%x", hdev->name, &ev->bdaddr,
 	       ev->link_type);
 
+	/* Reject incoming connection from device with same BD ADDR against
+	 * CVE-2020-26555
+	 */
+	if (hdev && !bacmp(&hdev->bdaddr, &ev->bdaddr)) {
+		bt_dev_dbg(hdev, "Reject connection with same BD_ADDR %pMR\n",
+			   &ev->bdaddr);
+		hci_reject_conn(hdev, &ev->bdaddr);
+		return;
+	}
+
 	mask |= hci_proto_connect_ind(hdev, &ev->bdaddr, ev->link_type,
 				      &flags);
 
@@ -2788,10 +2850,12 @@
 		return;
 	}
 
+	hci_dev_lock(hdev);
+
 	if (hci_bdaddr_list_lookup(&hdev->reject_list, &ev->bdaddr,
 				   BDADDR_BREDR)) {
 		hci_reject_conn(hdev, &ev->bdaddr);
-		return;
+		goto unlock;
 	}
 
 	/* Require HCI_CONNECTABLE or an accept list entry to accept the
@@ -2803,13 +2867,11 @@
 	    !hci_bdaddr_list_lookup_with_flags(&hdev->accept_list, &ev->bdaddr,
 					       BDADDR_BREDR)) {
 		hci_reject_conn(hdev, &ev->bdaddr);
-		return;
+		goto unlock;
 	}
 
 	/* Connection accepted */
 
-	hci_dev_lock(hdev);
-
 	ie = hci_inquiry_cache_lookup(hdev, &ev->bdaddr);
 	if (ie)
 		memcpy(ie->data.dev_class, ev->dev_class, 3);
@@ -2819,10 +2881,9 @@
 	if (!conn) {
 		conn = hci_conn_add(hdev, ev->link_type, &ev->bdaddr,
 				    HCI_ROLE_SLAVE);
-		if (!conn) {
-			bt_dev_err(hdev, "no memory for new connection");
-			hci_dev_unlock(hdev);
-			return;
+		if (IS_ERR(conn)) {
+			bt_dev_err(hdev, "connection err: %ld", PTR_ERR(conn));
+			goto unlock;
 		}
 	}
 
@@ -2862,6 +2923,10 @@
 		conn->state = BT_CONNECT2;
 		hci_connect_cfm(conn, 0);
 	}
+
+	return;
+unlock:
+	hci_dev_unlock(hdev);
 }
 
 static u8 hci_to_mgmt_reason(u8 err)
@@ -2987,14 +3052,8 @@
 
 	if (!ev->status) {
 		clear_bit(HCI_CONN_AUTH_FAILURE, &conn->flags);
-
-		if (!hci_conn_ssp_enabled(conn) &&
-		    test_bit(HCI_CONN_REAUTH_PEND, &conn->flags)) {
-			bt_dev_info(hdev, "re-auth of legacy device is not possible.");
-		} else {
-			set_bit(HCI_CONN_AUTH, &conn->flags);
-			conn->sec_level = conn->pending_sec_level;
-		}
+		set_bit(HCI_CONN_AUTH, &conn->flags);
+		conn->sec_level = conn->pending_sec_level;
 	} else {
 		if (ev->status == HCI_ERROR_PIN_OR_KEY_MISSING)
 			set_bit(HCI_CONN_AUTH_FAILURE, &conn->flags);
@@ -3003,7 +3062,6 @@
 	}
 
 	clear_bit(HCI_CONN_AUTH_PEND, &conn->flags);
-	clear_bit(HCI_CONN_REAUTH_PEND, &conn->flags);
 
 	if (conn->state == BT_CONFIG) {
 		if (!ev->status && hci_conn_ssp_enabled(conn)) {
@@ -3049,8 +3107,6 @@
 
 	BT_DBG("%s", hdev->name);
 
-	hci_conn_check_pending(hdev);
-
 	hci_dev_lock(hdev);
 
 	conn = hci_conn_hash_lookup_ba(hdev, ACL_LINK, &ev->bdaddr);
@@ -3090,6 +3146,7 @@
 	const struct hci_rp_read_enc_key_size *rp;
 	struct hci_conn *conn;
 	u16 handle;
+	u8 rp_status;
 
 	BT_DBG("%s status 0x%02x", hdev->name, status);
 
@@ -3099,6 +3156,7 @@
 	}
 
 	rp = (void *)skb->data;
+	rp_status = rp->status;
 	handle = le16_to_cpu(rp->handle);
 
 	hci_dev_lock(hdev);
@@ -3111,15 +3169,30 @@
 	 * secure approach is to then assume the key size is 0 to force a
 	 * disconnection.
 	 */
-	if (rp->status) {
+	if (rp_status) {
 		bt_dev_err(hdev, "failed to read key size for handle %u",
 			   handle);
 		conn->enc_key_size = 0;
 	} else {
 		conn->enc_key_size = rp->key_size;
+		rp_status = 0;
+
+		if (conn->enc_key_size < hdev->min_enc_key_size) {
+			/* As slave role, the conn->state has been set to
+			 * BT_CONNECTED and l2cap conn req might not be received
+			 * yet, at this moment the l2cap layer almost does
+			 * nothing with the non-zero status.
+			 * So we also clear encrypt related bits, and then the
+			 * handler of l2cap conn req will get the right secure
+			 * state at a later time.
+			 */
+			rp_status = HCI_ERROR_AUTH_FAILURE;
+			clear_bit(HCI_CONN_ENCRYPT, &conn->flags);
+			clear_bit(HCI_CONN_AES_CCM, &conn->flags);
+		}
 	}
 
-	hci_encrypt_cfm(conn, 0);
+	hci_encrypt_cfm(conn, rp_status);
 
 unlock:
 	hci_dev_unlock(hdev);
@@ -3292,7 +3365,7 @@
 		goto unlock;
 	}
 
-	if (!ev->status && !test_bit(HCI_CONN_MGMT_CONNECTED, &conn->flags)) {
+	if (!ev->status) {
 		struct hci_cp_remote_name_req cp;
 		memset(&cp, 0, sizeof(cp));
 		bacpy(&cp.bdaddr, &conn->dst);
@@ -3464,7 +3537,7 @@
 		break;
 
 	case HCI_OP_READ_BUFFER_SIZE:
-		hci_cc_read_buffer_size(hdev, skb);
+		*status = hci_cc_read_buffer_size(hdev, skb);
 		break;
 
 	case HCI_OP_READ_BD_ADDR:
@@ -3536,7 +3609,7 @@
 		break;
 
 	case HCI_OP_LE_READ_BUFFER_SIZE:
-		hci_cc_le_read_buffer_size(hdev, skb);
+		*status = hci_cc_le_read_buffer_size(hdev, skb);
 		break;
 
 	case HCI_OP_LE_READ_LOCAL_FEATURES:
@@ -4156,6 +4229,15 @@
 	if (!conn)
 		goto unlock;
 
+	/* Ignore NULL link key against CVE-2020-26555 */
+	if (!crypto_memneq(ev->link_key, ZERO_KEY, HCI_LINK_KEY_SIZE)) {
+		bt_dev_dbg(hdev, "Ignore NULL link key (ZERO KEY) for %pMR",
+			   &ev->bdaddr);
+		hci_disconnect(conn, HCI_ERROR_AUTH_FAILURE);
+		hci_conn_drop(conn);
+		goto unlock;
+	}
+
 	hci_conn_hold(conn);
 	conn->disc_timeout = HCI_DISCONN_TIMEOUT;
 	hci_conn_drop(conn);
@@ -4398,6 +4480,19 @@
 	struct hci_ev_sync_conn_complete *ev = (void *) skb->data;
 	struct hci_conn *conn;
 
+	switch (ev->link_type) {
+	case SCO_LINK:
+	case ESCO_LINK:
+		break;
+	default:
+		/* As per Core 5.3 Vol 4 Part E 7.7.35 (p.2219), Link_Type
+		 * for HCI_Synchronous_Connection_Complete is limited to
+		 * either SCO or eSCO
+		 */
+		bt_dev_err(hdev, "Ignoring connect complete event for invalid link type");
+		return;
+	}
+
 	BT_DBG("%s status 0x%2.2x", hdev->name, ev->status);
 
 	hci_dev_lock(hdev);
@@ -4647,8 +4742,8 @@
 		 * available, then do not declare that OOB data is
 		 * present.
 		 */
-		if (!memcmp(data->rand256, ZERO_KEY, 16) ||
-		    !memcmp(data->hash256, ZERO_KEY, 16))
+		if (!crypto_memneq(data->rand256, ZERO_KEY, 16) ||
+		    !crypto_memneq(data->hash256, ZERO_KEY, 16))
 			return 0x00;
 
 		return 0x02;
@@ -4658,8 +4753,8 @@
 	 * not supported by the hardware, then check that if
 	 * P-192 data values are present.
 	 */
-	if (!memcmp(data->rand192, ZERO_KEY, 16) ||
-	    !memcmp(data->hash192, ZERO_KEY, 16))
+	if (!crypto_memneq(data->rand192, ZERO_KEY, 16) ||
+	    !crypto_memneq(data->hash192, ZERO_KEY, 16))
 		return 0x00;
 
 	return 0x01;
@@ -4675,9 +4770,12 @@
 	hci_dev_lock(hdev);
 
 	conn = hci_conn_hash_lookup_ba(hdev, ACL_LINK, &ev->bdaddr);
-	if (!conn)
+	if (!conn || !hci_dev_test_flag(hdev, HCI_SSP_ENABLED))
 		goto unlock;
 
+	/* Assume remote supports SSP since it has triggered this event */
+	set_bit(HCI_CONN_SSP_ENABLED, &conn->flags);
+
 	hci_conn_hold(conn);
 
 	if (!hci_dev_test_flag(hdev, HCI_MGMT))
@@ -4788,19 +4886,16 @@
 		goto unlock;
 	}
 
-	/* If no side requires MITM protection; auto-accept */
+	/* If no side requires MITM protection; use JUST_CFM method */
 	if ((!loc_mitm || conn->remote_cap == HCI_IO_NO_INPUT_OUTPUT) &&
 	    (!rem_mitm || conn->io_capability == HCI_IO_NO_INPUT_OUTPUT)) {
 
-		/* If we're not the initiators request authorization to
-		 * proceed from user space (mgmt_user_confirm with
-		 * confirm_hint set to 1). The exception is if neither
-		 * side had MITM or if the local IO capability is
-		 * NoInputNoOutput, in which case we do auto-accept
+		/* If we're not the initiator of request authorization and the
+		 * local IO capability is not NoInputNoOutput, use JUST_WORKS
+		 * method (mgmt_user_confirm with confirm_hint set to 1).
 		 */
 		if (!test_bit(HCI_CONN_AUTH_PEND, &conn->flags) &&
-		    conn->io_capability != HCI_IO_NO_INPUT_OUTPUT &&
-		    (loc_mitm || rem_mitm)) {
+		    conn->io_capability != HCI_IO_NO_INPUT_OUTPUT) {
 			BT_DBG("Confirming auto-accept as acceptor");
 			confirm_hint = 1;
 			goto confirm;
@@ -4920,7 +5015,7 @@
 	hci_dev_lock(hdev);
 
 	conn = hci_conn_hash_lookup_ba(hdev, ACL_LINK, &ev->bdaddr);
-	if (!conn)
+	if (!conn || !hci_conn_ssp_enabled(conn))
 		goto unlock;
 
 	/* Reset the authentication requirement to unknown */
@@ -5151,8 +5246,9 @@
 	hci_dev_lock(hdev);
 
 	hcon = hci_conn_hash_lookup_handle(hdev, ev->phy_handle);
-	if (hcon) {
+	if (hcon && hcon->type == AMP_LINK) {
 		hcon->state = BT_CLOSED;
+		hci_disconn_cfm(hcon, ev->reason);
 		hci_conn_del(hcon);
 	}
 
@@ -5234,8 +5330,8 @@
 	conn = hci_lookup_le_connect(hdev);
 	if (!conn) {
 		conn = hci_conn_add(hdev, LE_LINK, bdaddr, role);
-		if (!conn) {
-			bt_dev_err(hdev, "no memory for new connection");
+		if (IS_ERR(conn)) {
+			bt_dev_err(hdev, "connection err: %ld", PTR_ERR(conn));
 			goto unlock;
 		}
 
@@ -5780,7 +5876,13 @@
 		struct hci_ev_le_advertising_info *ev = ptr;
 		s8 rssi;
 
-		if (ev->length <= HCI_MAX_AD_LENGTH) {
+		if (ptr > (void *)skb_tail_pointer(skb) - sizeof(*ev)) {
+			bt_dev_err(hdev, "Malicious advertising data.");
+			break;
+		}
+
+		if (ev->length <= HCI_MAX_AD_LENGTH &&
+		    ev->data + ev->length <= skb_tail_pointer(skb)) {
 			rssi = ev->data[ev->length];
 			process_adv_report(hdev, ev->evt_type, &ev->bdaddr,
 					   ev->bdaddr_type, NULL, 0, rssi,
@@ -6003,6 +6105,10 @@
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_UNKNOWN_CONN_ID);
 
+	if (max > hcon->le_conn_max_interval)
+		return send_conn_param_neg_reply(hdev, handle,
+						 HCI_ERROR_INVALID_LL_PARAMS);
+
 	if (hci_check_conn_params(min, max, latency, timeout))
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_INVALID_LL_PARAMS);
@@ -6220,10 +6326,10 @@
 	 * keep track of the bdaddr of the connection event that woke us up.
 	 */
 	if (event == HCI_EV_CONN_REQUEST) {
-		bacpy(&hdev->wake_addr, &conn_complete->bdaddr);
+		bacpy(&hdev->wake_addr, &conn_request->bdaddr);
 		hdev->wake_addr_type = BDADDR_BREDR;
 	} else if (event == HCI_EV_CONN_COMPLETE) {
-		bacpy(&hdev->wake_addr, &conn_request->bdaddr);
+		bacpy(&hdev->wake_addr, &conn_complete->bdaddr);
 		hdev->wake_addr_type = BDADDR_BREDR;
 	} else if (event == HCI_EV_LE_META) {
 		struct hci_ev_le_meta *le_ev = (void *)skb->data;
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_request.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_request.c
@@ -108,8 +108,10 @@
 	if (hdev->req_status == HCI_REQ_PEND) {
 		hdev->req_result = result;
 		hdev->req_status = HCI_REQ_DONE;
-		if (skb)
+		if (skb) {
+			kfree_skb(hdev->req_skb);
 			hdev->req_skb = skb_get(skb);
+		}
 		wake_up_interruptible(&hdev->req_wait_q);
 	}
 }
@@ -2318,7 +2320,7 @@
 	/* Set duration per instance since controller is responsible for
 	 * scheduling it.
 	 */
-	if (adv_instance && adv_instance->duration) {
+	if (adv_instance && adv_instance->timeout) {
 		u16 duration = adv_instance->timeout * MSEC_PER_SEC;
 
 		/* Time = N * 10 ms */
@@ -3174,6 +3176,7 @@
 	if (err < 0)
 		own_addr_type = ADDR_LE_DEV_PUBLIC;
 
+	hci_dev_lock(hdev);
 	if (hci_is_adv_monitoring(hdev)) {
 		/* Duplicate filter should be disabled when some advertisement
 		 * monitor is activated, otherwise AdvMon can only receive one
@@ -3190,6 +3193,7 @@
 		 */
 		filter_dup = LE_SCAN_FILTER_DUP_DISABLE;
 	}
+	hci_dev_unlock(hdev);
 
 	hci_req_start_scan(req, LE_SCAN_ACTIVE, interval,
 			   hdev->le_scan_window_discovery, own_addr_type,
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_sock.c
@@ -438,7 +438,8 @@
 		ni->type = hdev->dev_type;
 		ni->bus = hdev->bus;
 		bacpy(&ni->bdaddr, &hdev->bdaddr);
-		memcpy(ni->name, hdev->name, 8);
+		memcpy_and_pad(ni->name, sizeof(ni->name), hdev->name,
+			       strnlen(hdev->name, sizeof(ni->name)), '\0');
 
 		opcode = cpu_to_le16(HCI_MON_NEW_INDEX);
 		break;
@@ -888,10 +889,6 @@
 	}
 
 	sock_orphan(sk);
-
-	skb_queue_purge(&sk->sk_receive_queue);
-	skb_queue_purge(&sk->sk_write_queue);
-
 	release_sock(sk);
 	sock_put(sk);
 	return 0;
@@ -984,6 +981,34 @@
 
 	BT_DBG("cmd %x arg %lx", cmd, arg);
 
+	/* Make sure the cmd is valid before doing anything */
+	switch (cmd) {
+	case HCIGETDEVLIST:
+	case HCIGETDEVINFO:
+	case HCIGETCONNLIST:
+	case HCIDEVUP:
+	case HCIDEVDOWN:
+	case HCIDEVRESET:
+	case HCIDEVRESTAT:
+	case HCISETSCAN:
+	case HCISETAUTH:
+	case HCISETENCRYPT:
+	case HCISETPTYPE:
+	case HCISETLINKPOL:
+	case HCISETLINKMODE:
+	case HCISETACLMTU:
+	case HCISETSCOMTU:
+	case HCIINQUIRY:
+	case HCISETRAW:
+	case HCIGETCONNINFO:
+	case HCIGETAUTHINFO:
+	case HCIBLOCKADDR:
+	case HCIUNBLOCKADDR:
+		break;
+	default:
+		return -ENOIOCTLCMD;
+	}
+
 	lock_sock(sk);
 
 	if (hci_pi(sk)->channel != HCI_CHANNEL_RAW) {
@@ -1000,7 +1025,14 @@
 	if (hci_sock_gen_cookie(sk)) {
 		struct sk_buff *skb;
 
-		if (capable(CAP_NET_ADMIN))
+		/* Perform careful checks before setting the HCI_SOCK_TRUSTED
+		 * flag. Make sure that not only the current task but also
+		 * the socket opener has the required capability, since
+		 * privileged programs can be tricked into making ioctl calls
+		 * on HCI sockets, and the socket should not be marked as
+		 * trusted simply because the ioctl caller is privileged.
+		 */
+		if (sk_capable(sk, CAP_NET_ADMIN))
 			hci_sock_set_flag(sk, HCI_SOCK_TRUSTED);
 
 		/* Send event to monitor */
@@ -1878,10 +1910,9 @@
 
 	switch (optname) {
 	case HCI_DATA_DIR:
-		if (copy_from_sockptr(&opt, optval, sizeof(opt))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, len);
+		if (err)
 			break;
-		}
 
 		if (opt)
 			hci_pi(sk)->cmsg_mask |= HCI_CMSG_DIR;
@@ -1890,10 +1921,9 @@
 		break;
 
 	case HCI_TIME_STAMP:
-		if (copy_from_sockptr(&opt, optval, sizeof(opt))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, len);
+		if (err)
 			break;
-		}
 
 		if (opt)
 			hci_pi(sk)->cmsg_mask |= HCI_CMSG_TSTAMP;
@@ -1911,11 +1941,9 @@
 			uf.event_mask[1] = *((u32 *) f->event_mask + 1);
 		}
 
-		len = min_t(unsigned int, len, sizeof(uf));
-		if (copy_from_sockptr(&uf, optval, len)) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&uf, sizeof(uf), optval, len);
+		if (err)
 			break;
-		}
 
 		if (!capable(CAP_NET_RAW)) {
 			uf.type_mask &= hci_sec_filter.type_mask;
@@ -2012,6 +2040,12 @@
 	return err;
 }
 
+static void hci_sock_destruct(struct sock *sk)
+{
+	skb_queue_purge(&sk->sk_receive_queue);
+	skb_queue_purge(&sk->sk_write_queue);
+}
+
 static const struct proto_ops hci_sock_ops = {
 	.family		= PF_BLUETOOTH,
 	.owner		= THIS_MODULE,
@@ -2065,6 +2099,7 @@
 
 	sock->state = SS_UNCONNECTED;
 	sk->sk_state = BT_OPEN;
+	sk->sk_destruct = hci_sock_destruct;
 
 	bt_sock_link(&hci_sk_list, sk);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hci_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hci_sysfs.c
@@ -19,21 +19,11 @@
 	.release = bt_link_release,
 };
 
-/*
- * The rfcomm tty device will possibly retain even when conn
- * is down, and sysfs doesn't support move zombie device,
- * so we should move the device before conn device is destroyed.
- */
-static int __match_tty(struct device *dev, void *data)
-{
-	return !strncmp(dev_name(dev), "rfcomm", 6);
-}
-
 void hci_conn_init_sysfs(struct hci_conn *conn)
 {
 	struct hci_dev *hdev = conn->hdev;
 
-	BT_DBG("conn %p", conn);
+	bt_dev_dbg(hdev, "conn %p", conn);
 
 	conn->dev.type = &bt_link;
 	conn->dev.class = bt_class;
@@ -46,38 +36,45 @@
 {
 	struct hci_dev *hdev = conn->hdev;
 
-	BT_DBG("conn %p", conn);
+	bt_dev_dbg(hdev, "conn %p", conn);
+
+	if (device_is_registered(&conn->dev))
+		return;
 
 	dev_set_name(&conn->dev, "%s:%d", hdev->name, conn->handle);
 
-	if (device_add(&conn->dev) < 0) {
+	if (device_add(&conn->dev) < 0)
 		bt_dev_err(hdev, "failed to register connection device");
-		return;
-	}
-
-	hci_dev_hold(hdev);
 }
 
 void hci_conn_del_sysfs(struct hci_conn *conn)
 {
 	struct hci_dev *hdev = conn->hdev;
 
-	if (!device_is_registered(&conn->dev))
+	bt_dev_dbg(hdev, "conn %p", conn);
+
+	if (!device_is_registered(&conn->dev)) {
+		/* If device_add() has *not* succeeded, use *only* put_device()
+		 * to drop the reference count.
+		 */
+		put_device(&conn->dev);
 		return;
+	}
 
+	/* If there are devices using the connection as parent reset it to NULL
+	 * before unregistering the device.
+	 */
 	while (1) {
 		struct device *dev;
 
-		dev = device_find_child(&conn->dev, NULL, __match_tty);
+		dev = device_find_any_child(&conn->dev);
 		if (!dev)
 			break;
 		device_move(dev, NULL, DPM_ORDER_DEV_LAST);
 		put_device(dev);
 	}
 
-	device_del(&conn->dev);
-
-	hci_dev_put(hdev);
+	device_unregister(&conn->dev);
 }
 
 static void bt_host_release(struct device *dev)
@@ -86,6 +83,8 @@
 
 	if (hci_dev_test_flag(hdev, HCI_UNREGISTER))
 		hci_release_dev(hdev);
+	else
+		kfree(hdev);
 	module_put(THIS_MODULE);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/hidp/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/hidp/core.c
@@ -433,7 +433,7 @@
 static void hidp_del_timer(struct hidp_session *session)
 {
 	if (session->idle_to > 0)
-		del_timer(&session->timer);
+		del_timer_sync(&session->timer);
 }
 
 static void hidp_process_report(struct hidp_session *session, int type,
@@ -1305,7 +1305,7 @@
 	l2cap_unregister_user(session->conn, &session->user);
 	hidp_session_put(session);
 
-	module_put_and_exit(0);
+	module_put_and_kthread_exit(0);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/l2cap_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/l2cap_core.c
@@ -61,6 +61,9 @@
 
 static void l2cap_tx(struct l2cap_chan *chan, struct l2cap_ctrl *control,
 		     struct sk_buff_head *skbs, u8 event);
+static void l2cap_retrans_timeout(struct work_struct *work);
+static void l2cap_monitor_timeout(struct work_struct *work);
+static void l2cap_ack_timeout(struct work_struct *work);
 
 static inline u8 bdaddr_type(u8 link_type, u8 bdaddr_type)
 {
@@ -111,7 +114,8 @@
 }
 
 /* Find channel with given SCID.
- * Returns locked channel. */
+ * Returns a reference locked channel.
+ */
 static struct l2cap_chan *l2cap_get_chan_by_scid(struct l2cap_conn *conn,
 						 u16 cid)
 {
@@ -119,15 +123,19 @@
 
 	mutex_lock(&conn->chan_lock);
 	c = __l2cap_get_chan_by_scid(conn, cid);
-	if (c)
-		l2cap_chan_lock(c);
+	if (c) {
+		/* Only lock if chan reference is not 0 */
+		c = l2cap_chan_hold_unless_zero(c);
+		if (c)
+			l2cap_chan_lock(c);
+	}
 	mutex_unlock(&conn->chan_lock);
 
 	return c;
 }
 
 /* Find channel with given DCID.
- * Returns locked channel.
+ * Returns a reference locked channel.
  */
 static struct l2cap_chan *l2cap_get_chan_by_dcid(struct l2cap_conn *conn,
 						 u16 cid)
@@ -136,8 +144,12 @@
 
 	mutex_lock(&conn->chan_lock);
 	c = __l2cap_get_chan_by_dcid(conn, cid);
-	if (c)
-		l2cap_chan_lock(c);
+	if (c) {
+		/* Only lock if chan reference is not 0 */
+		c = l2cap_chan_hold_unless_zero(c);
+		if (c)
+			l2cap_chan_lock(c);
+	}
 	mutex_unlock(&conn->chan_lock);
 
 	return c;
@@ -162,8 +174,12 @@
 
 	mutex_lock(&conn->chan_lock);
 	c = __l2cap_get_chan_by_ident(conn, ident);
-	if (c)
-		l2cap_chan_lock(c);
+	if (c) {
+		/* Only lock if chan reference is not 0 */
+		c = l2cap_chan_hold_unless_zero(c);
+		if (c)
+			l2cap_chan_lock(c);
+	}
 	mutex_unlock(&conn->chan_lock);
 
 	return c;
@@ -419,6 +435,9 @@
 
 	BT_DBG("chan %p state %s", chan, state_to_string(chan->state));
 
+	if (!conn)
+		return;
+
 	mutex_lock(&conn->chan_lock);
 	/* __set_chan_timer() calls l2cap_chan_hold(chan) while scheduling
 	 * this work. No need to call l2cap_chan_hold(chan) here again.
@@ -463,6 +482,9 @@
 	write_unlock(&chan_list_lock);
 
 	INIT_DELAYED_WORK(&chan->chan_timer, l2cap_chan_timeout);
+	INIT_DELAYED_WORK(&chan->retrans_timer, l2cap_retrans_timeout);
+	INIT_DELAYED_WORK(&chan->monitor_timer, l2cap_monitor_timeout);
+	INIT_DELAYED_WORK(&chan->ack_timer, l2cap_ack_timeout);
 
 	chan->state = BT_OPEN;
 
@@ -497,6 +519,16 @@
 	kref_get(&c->kref);
 }
 
+struct l2cap_chan *l2cap_chan_hold_unless_zero(struct l2cap_chan *c)
+{
+	BT_DBG("chan %p orig refcnt %u", c, kref_read(&c->kref));
+
+	if (!kref_get_unless_zero(&c->kref))
+		return NULL;
+
+	return c;
+}
+
 void l2cap_chan_put(struct l2cap_chan *c)
 {
 	BT_DBG("chan %p orig refcnt %u", c, kref_read(&c->kref));
@@ -600,7 +632,8 @@
 	    test_bit(FLAG_HOLD_HCI_CONN, &chan->flags))
 		hci_conn_hold(conn->hcon);
 
-	list_add(&chan->list, &conn->chan_l);
+	/* Append to the list since the order matters for ECRED */
+	list_add_tail(&chan->list, &conn->chan_l);
 }
 
 void l2cap_chan_add(struct l2cap_conn *conn, struct l2cap_chan *chan)
@@ -679,6 +712,17 @@
 }
 EXPORT_SYMBOL_GPL(l2cap_chan_del);
 
+static void __l2cap_chan_list_id(struct l2cap_conn *conn, u16 id,
+				 l2cap_chan_func_t func, void *data)
+{
+	struct l2cap_chan *chan, *l;
+
+	list_for_each_entry_safe(chan, l, &conn->chan_l, list) {
+		if (chan->ident == id)
+			func(chan, data);
+	}
+}
+
 static void __l2cap_chan_list(struct l2cap_conn *conn, l2cap_chan_func_t func,
 			      void *data)
 {
@@ -746,23 +790,9 @@
 
 static void l2cap_chan_ecred_connect_reject(struct l2cap_chan *chan)
 {
-	struct l2cap_conn *conn = chan->conn;
-	struct l2cap_ecred_conn_rsp rsp;
-	u16 result;
-
-	if (test_bit(FLAG_DEFER_SETUP, &chan->flags))
-		result = L2CAP_CR_LE_AUTHORIZATION;
-	else
-		result = L2CAP_CR_LE_BAD_PSM;
-
 	l2cap_state_change(chan, BT_DISCONN);
 
-	memset(&rsp, 0, sizeof(rsp));
-
-	rsp.result  = cpu_to_le16(result);
-
-	l2cap_send_cmd(conn, chan->ident, L2CAP_LE_CONN_RSP, sizeof(rsp),
-		       &rsp);
+	__l2cap_ecred_conn_rsp_defer(chan);
 }
 
 static void l2cap_chan_connect_reject(struct l2cap_chan *chan)
@@ -817,7 +847,7 @@
 					break;
 				case L2CAP_MODE_EXT_FLOWCTL:
 					l2cap_chan_ecred_connect_reject(chan);
-					break;
+					return;
 				}
 			}
 		}
@@ -1436,6 +1466,7 @@
 
 	l2cap_ecred_init(chan, 0);
 
+	memset(&data, 0, sizeof(data));
 	data.pdu.req.psm     = chan->psm;
 	data.pdu.req.mtu     = cpu_to_le16(chan->imtu);
 	data.pdu.req.mps     = cpu_to_le16(chan->mps);
@@ -1946,11 +1977,11 @@
 						   bdaddr_t *dst,
 						   u8 link_type)
 {
-	struct l2cap_chan *c, *c1 = NULL;
+	struct l2cap_chan *c, *tmp, *c1 = NULL;
 
 	read_lock(&chan_list_lock);
 
-	list_for_each_entry(c, &chan_list, global_l) {
+	list_for_each_entry_safe(c, tmp, &chan_list, global_l) {
 		if (state && c->state != state)
 			continue;
 
@@ -1960,7 +1991,7 @@
 		if (link_type == LE_LINK && c->src_type == BDADDR_BREDR)
 			continue;
 
-		if (c->psm == psm) {
+		if (c->chan_type != L2CAP_CHAN_FIXED && c->psm == psm) {
 			int src_match, dst_match;
 			int src_any, dst_any;
 
@@ -1968,7 +1999,9 @@
 			src_match = !bacmp(&c->src, src);
 			dst_match = !bacmp(&c->dst, dst);
 			if (src_match && dst_match) {
-				l2cap_chan_hold(c);
+				if (!l2cap_chan_hold_unless_zero(c))
+					continue;
+
 				read_unlock(&chan_list_lock);
 				return c;
 			}
@@ -1983,7 +2016,7 @@
 	}
 
 	if (c1)
-		l2cap_chan_hold(c1);
+		c1 = l2cap_chan_hold_unless_zero(c1);
 
 	read_unlock(&chan_list_lock);
 
@@ -2651,14 +2684,6 @@
 		if (IS_ERR(skb))
 			return PTR_ERR(skb);
 
-		/* Channel lock is released before requesting new skb and then
-		 * reacquired thus we need to recheck channel state.
-		 */
-		if (chan->state != BT_CONNECTED) {
-			kfree_skb(skb);
-			return -ENOTCONN;
-		}
-
 		l2cap_do_send(chan, skb);
 		return len;
 	}
@@ -2703,14 +2728,6 @@
 		if (IS_ERR(skb))
 			return PTR_ERR(skb);
 
-		/* Channel lock is released before requesting new skb and then
-		 * reacquired thus we need to recheck channel state.
-		 */
-		if (chan->state != BT_CONNECTED) {
-			kfree_skb(skb);
-			return -ENOTCONN;
-		}
-
 		l2cap_do_send(chan, skb);
 		err = len;
 		break;
@@ -2731,14 +2748,6 @@
 		 */
 		err = l2cap_segment_sdu(chan, &seg_queue, msg, len);
 
-		/* The channel could have been closed while segmenting,
-		 * check that it is still connected.
-		 */
-		if (chan->state != BT_CONNECTED) {
-			__skb_queue_purge(&seg_queue);
-			err = -ENOTCONN;
-		}
-
 		if (err)
 			break;
 
@@ -3294,10 +3303,6 @@
 	chan->rx_state = L2CAP_RX_STATE_RECV;
 	chan->tx_state = L2CAP_TX_STATE_XMIT;
 
-	INIT_DELAYED_WORK(&chan->retrans_timer, l2cap_retrans_timeout);
-	INIT_DELAYED_WORK(&chan->monitor_timer, l2cap_monitor_timeout);
-	INIT_DELAYED_WORK(&chan->ack_timer, l2cap_ack_timeout);
-
 	skb_queue_head_init(&chan->srej_q);
 
 	err = l2cap_seq_list_init(&chan->srej_list, chan->tx_win);
@@ -3736,7 +3741,8 @@
 			l2cap_add_conf_opt(&ptr, L2CAP_CONF_RFC,
 					   sizeof(rfc), (unsigned long) &rfc, endptr - ptr);
 
-			if (test_bit(FLAG_EFS_ENABLE, &chan->flags)) {
+			if (remote_efs &&
+			    test_bit(FLAG_EFS_ENABLE, &chan->flags)) {
 				chan->remote_id = efs.id;
 				chan->remote_stype = efs.stype;
 				chan->remote_msdu = le16_to_cpu(efs.msdu);
@@ -3933,43 +3939,90 @@
 		       &rsp);
 }
 
-void __l2cap_ecred_conn_rsp_defer(struct l2cap_chan *chan)
+static void l2cap_ecred_list_defer(struct l2cap_chan *chan, void *data)
 {
+	int *result = data;
+
+	if (*result || test_bit(FLAG_ECRED_CONN_REQ_SENT, &chan->flags))
+		return;
+
+	switch (chan->state) {
+	case BT_CONNECT2:
+		/* If channel still pending accept add to result */
+		(*result)++;
+		return;
+	case BT_CONNECTED:
+		return;
+	default:
+		/* If not connected or pending accept it has been refused */
+		*result = -ECONNREFUSED;
+		return;
+	}
+}
+
+struct l2cap_ecred_rsp_data {
 	struct {
 		struct l2cap_ecred_conn_rsp rsp;
-		__le16 dcid[5];
+		__le16 scid[L2CAP_ECRED_MAX_CID];
 	} __packed pdu;
+	int count;
+};
+
+static void l2cap_ecred_rsp_defer(struct l2cap_chan *chan, void *data)
+{
+	struct l2cap_ecred_rsp_data *rsp = data;
+
+	/* Check if channel for outgoing connection or if it wasn't deferred
+	 * since in those cases it must be skipped.
+	 */
+	if (test_bit(FLAG_ECRED_CONN_REQ_SENT, &chan->flags) ||
+	    !test_and_clear_bit(FLAG_DEFER_SETUP, &chan->flags))
+		return;
+
+	/* Reset ident so only one response is sent */
+	chan->ident = 0;
+
+	/* Include all channels pending with the same ident */
+	if (!rsp->pdu.rsp.result)
+		rsp->pdu.rsp.dcid[rsp->count++] = cpu_to_le16(chan->scid);
+	else
+		l2cap_chan_del(chan, ECONNRESET);
+}
+
+void __l2cap_ecred_conn_rsp_defer(struct l2cap_chan *chan)
+{
 	struct l2cap_conn *conn = chan->conn;
-	u16 ident = chan->ident;
-	int i = 0;
+	struct l2cap_ecred_rsp_data data;
+	u16 id = chan->ident;
+	int result = 0;
 
-	if (!ident)
+	if (!id)
 		return;
 
-	BT_DBG("chan %p ident %d", chan, ident);
+	BT_DBG("chan %p id %d", chan, id);
 
-	pdu.rsp.mtu     = cpu_to_le16(chan->imtu);
-	pdu.rsp.mps     = cpu_to_le16(chan->mps);
-	pdu.rsp.credits = cpu_to_le16(chan->rx_credits);
-	pdu.rsp.result  = cpu_to_le16(L2CAP_CR_LE_SUCCESS);
+	memset(&data, 0, sizeof(data));
 
-	mutex_lock(&conn->chan_lock);
+	data.pdu.rsp.mtu     = cpu_to_le16(chan->imtu);
+	data.pdu.rsp.mps     = cpu_to_le16(chan->mps);
+	data.pdu.rsp.credits = cpu_to_le16(chan->rx_credits);
+	data.pdu.rsp.result  = cpu_to_le16(L2CAP_CR_LE_SUCCESS);
 
-	list_for_each_entry(chan, &conn->chan_l, list) {
-		if (chan->ident != ident)
-			continue;
+	/* Verify that all channels are ready */
+	__l2cap_chan_list_id(conn, id, l2cap_ecred_list_defer, &result);
 
-		/* Reset ident so only one response is sent */
-		chan->ident = 0;
+	if (result > 0)
+		return;
 
-		/* Include all channels pending with the same ident */
-		pdu.dcid[i++] = cpu_to_le16(chan->scid);
-	}
+	if (result < 0)
+		data.pdu.rsp.result = cpu_to_le16(L2CAP_CR_LE_AUTHORIZATION);
 
-	mutex_unlock(&conn->chan_lock);
+	/* Build response */
+	__l2cap_chan_list_id(conn, id, l2cap_ecred_rsp_defer, &data);
 
-	l2cap_send_cmd(conn, ident, L2CAP_ECRED_CONN_RSP,
-			sizeof(pdu.rsp) + i * sizeof(__le16), &pdu);
+	l2cap_send_cmd(conn, id, L2CAP_ECRED_CONN_RSP,
+		       sizeof(data.pdu.rsp) + (data.count * sizeof(__le16)),
+		       &data.pdu);
 }
 
 void __l2cap_connect_rsp_defer(struct l2cap_chan *chan)
@@ -4228,18 +4281,9 @@
 static int l2cap_connect_req(struct l2cap_conn *conn,
 			     struct l2cap_cmd_hdr *cmd, u16 cmd_len, u8 *data)
 {
-	struct hci_dev *hdev = conn->hcon->hdev;
-	struct hci_conn *hcon = conn->hcon;
-
 	if (cmd_len < sizeof(struct l2cap_conn_req))
 		return -EPROTO;
 
-	hci_dev_lock(hdev);
-	if (hci_dev_test_flag(hdev, HCI_MGMT) &&
-	    !test_and_set_bit(HCI_CONN_MGMT_CONNECTED, &hcon->flags))
-		mgmt_device_connected(hdev, hcon, NULL, 0);
-	hci_dev_unlock(hdev);
-
 	l2cap_connect(conn, cmd, data, L2CAP_CONN_RSP, 0);
 	return 0;
 }
@@ -4262,6 +4306,10 @@
 	result = __le16_to_cpu(rsp->result);
 	status = __le16_to_cpu(rsp->status);
 
+	if (result == L2CAP_CR_SUCCESS && (dcid < L2CAP_CID_DYN_START ||
+					   dcid > L2CAP_CID_DYN_END))
+		return -EPROTO;
+
 	BT_DBG("dcid 0x%4.4x scid 0x%4.4x result 0x%2.2x status 0x%2.2x",
 	       dcid, scid, result, status);
 
@@ -4281,12 +4329,23 @@
 		}
 	}
 
+	chan = l2cap_chan_hold_unless_zero(chan);
+	if (!chan) {
+		err = -EBADSLT;
+		goto unlock;
+	}
+
 	err = 0;
 
 	l2cap_chan_lock(chan);
 
 	switch (result) {
 	case L2CAP_CR_SUCCESS:
+		if (__l2cap_get_chan_by_dcid(conn, dcid)) {
+			err = -EBADSLT;
+			break;
+		}
+
 		l2cap_state_change(chan, BT_CONFIG);
 		chan->ident = 0;
 		chan->dcid = dcid;
@@ -4310,6 +4369,7 @@
 	}
 
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 unlock:
 	mutex_unlock(&conn->chan_lock);
@@ -4417,7 +4477,8 @@
 
 	chan->ident = cmd->ident;
 	l2cap_send_cmd(conn, cmd->ident, L2CAP_CONF_RSP, len, rsp);
-	chan->num_conf_rsp++;
+	if (chan->num_conf_rsp < L2CAP_CONF_MAX_CONF_RSP)
+		chan->num_conf_rsp++;
 
 	/* Reset config buffer. */
 	chan->conf_len = 0;
@@ -4463,6 +4524,7 @@
 
 unlock:
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 	return err;
 }
 
@@ -4577,6 +4639,7 @@
 
 done:
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 	return err;
 }
 
@@ -4597,33 +4660,29 @@
 
 	BT_DBG("scid 0x%4.4x dcid 0x%4.4x", scid, dcid);
 
-	mutex_lock(&conn->chan_lock);
-
-	chan = __l2cap_get_chan_by_scid(conn, dcid);
+	chan = l2cap_get_chan_by_scid(conn, dcid);
 	if (!chan) {
-		mutex_unlock(&conn->chan_lock);
 		cmd_reject_invalid_cid(conn, cmd->ident, dcid, scid);
 		return 0;
 	}
 
-	l2cap_chan_hold(chan);
-	l2cap_chan_lock(chan);
-
 	rsp.dcid = cpu_to_le16(chan->scid);
 	rsp.scid = cpu_to_le16(chan->dcid);
 	l2cap_send_cmd(conn, cmd->ident, L2CAP_DISCONN_RSP, sizeof(rsp), &rsp);
 
 	chan->ops->set_shutdown(chan);
 
+	l2cap_chan_unlock(chan);
+	mutex_lock(&conn->chan_lock);
+	l2cap_chan_lock(chan);
 	l2cap_chan_del(chan, ECONNRESET);
+	mutex_unlock(&conn->chan_lock);
 
 	chan->ops->close(chan);
 
 	l2cap_chan_unlock(chan);
 	l2cap_chan_put(chan);
 
-	mutex_unlock(&conn->chan_lock);
-
 	return 0;
 }
 
@@ -4643,33 +4702,28 @@
 
 	BT_DBG("dcid 0x%4.4x scid 0x%4.4x", dcid, scid);
 
-	mutex_lock(&conn->chan_lock);
-
-	chan = __l2cap_get_chan_by_scid(conn, scid);
+	chan = l2cap_get_chan_by_scid(conn, scid);
 	if (!chan) {
-		mutex_unlock(&conn->chan_lock);
 		return 0;
 	}
 
-	l2cap_chan_hold(chan);
-	l2cap_chan_lock(chan);
-
 	if (chan->state != BT_DISCONN) {
 		l2cap_chan_unlock(chan);
 		l2cap_chan_put(chan);
-		mutex_unlock(&conn->chan_lock);
 		return 0;
 	}
 
+	l2cap_chan_unlock(chan);
+	mutex_lock(&conn->chan_lock);
+	l2cap_chan_lock(chan);
 	l2cap_chan_del(chan, 0);
+	mutex_unlock(&conn->chan_lock);
 
 	chan->ops->close(chan);
 
 	l2cap_chan_unlock(chan);
 	l2cap_chan_put(chan);
 
-	mutex_unlock(&conn->chan_lock);
-
 	return 0;
 }
 
@@ -5304,6 +5358,7 @@
 	l2cap_send_move_chan_rsp(chan, result);
 
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 	return 0;
 }
@@ -5396,6 +5451,7 @@
 	}
 
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 }
 
 static void l2cap_move_fail(struct l2cap_conn *conn, u8 ident, u16 icid,
@@ -5425,6 +5481,7 @@
 	l2cap_send_move_chan_cfm(chan, L2CAP_MC_UNCONFIRMED);
 
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 }
 
 static int l2cap_move_channel_rsp(struct l2cap_conn *conn,
@@ -5488,6 +5545,7 @@
 	l2cap_send_move_chan_cfm_rsp(conn, cmd->ident, icid);
 
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 	return 0;
 }
@@ -5523,6 +5581,7 @@
 	}
 
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 	return 0;
 }
@@ -5771,6 +5830,19 @@
 	BT_DBG("psm 0x%2.2x scid 0x%4.4x mtu %u mps %u", __le16_to_cpu(psm),
 	       scid, mtu, mps);
 
+	/* BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 3, Part A
+	 * page 1059:
+	 *
+	 * Valid range: 0x0001-0x00ff
+	 *
+	 * Table 4.15: L2CAP_LE_CREDIT_BASED_CONNECTION_REQ SPSM ranges
+	 */
+	if (!psm || __le16_to_cpu(psm) > L2CAP_PSM_LE_DYN_END) {
+		result = L2CAP_CR_LE_BAD_PSM;
+		chan = NULL;
+		goto response;
+	}
+
 	/* Check if we have socket listening on psm */
 	pchan = l2cap_global_chan_by_psm(BT_LISTEN, psm, &conn->hcon->src,
 					 &conn->hcon->dst, LE_LINK);
@@ -5895,12 +5967,11 @@
 	if (credits > max_credits) {
 		BT_ERR("LE credits overflow");
 		l2cap_send_disconn_req(chan, ECONNRESET);
-		l2cap_chan_unlock(chan);
 
 		/* Return 0 so that we don't trigger an unnecessary
 		 * command reject packet.
 		 */
-		return 0;
+		goto unlock;
 	}
 
 	chan->tx_credits += credits;
@@ -5911,7 +5982,9 @@
 	if (chan->tx_credits)
 		chan->ops->resume(chan);
 
+unlock:
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 	return 0;
 }
@@ -5958,6 +6031,18 @@
 
 	psm  = req->psm;
 
+	/* BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 3, Part A
+	 * page 1059:
+	 *
+	 * Valid range: 0x0001-0x00ff
+	 *
+	 * Table 4.15: L2CAP_LE_CREDIT_BASED_CONNECTION_REQ SPSM ranges
+	 */
+	if (!psm || __le16_to_cpu(psm) > L2CAP_PSM_LE_DYN_END) {
+		result = L2CAP_CR_LE_BAD_PSM;
+		goto response;
+	}
+
 	BT_DBG("psm 0x%2.2x mtu %u mps %u", __le16_to_cpu(psm), mtu, mps);
 
 	memset(&pdu, 0, sizeof(pdu));
@@ -6032,6 +6117,7 @@
 		__set_chan_timer(chan, chan->ops->get_sndtimeo(chan));
 
 		chan->ident = cmd->ident;
+		chan->mode = L2CAP_MODE_EXT_FLOWCTL;
 
 		if (test_bit(FLAG_DEFER_SETUP, &chan->flags)) {
 			l2cap_state_change(chan, BT_CONNECT2);
@@ -6288,9 +6374,14 @@
 	if (!chan)
 		goto done;
 
+	chan = l2cap_chan_hold_unless_zero(chan);
+	if (!chan)
+		goto done;
+
 	l2cap_chan_lock(chan);
 	l2cap_chan_del(chan, ECONNREFUSED);
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 done:
 	mutex_unlock(&conn->chan_lock);
@@ -6401,6 +6492,14 @@
 	kfree_skb(skb);
 }
 
+static inline void l2cap_sig_send_rej(struct l2cap_conn *conn, u16 ident)
+{
+	struct l2cap_cmd_rej_unk rej;
+
+	rej.reason = cpu_to_le16(L2CAP_REJ_NOT_UNDERSTOOD);
+	l2cap_send_cmd(conn, ident, L2CAP_COMMAND_REJ, sizeof(rej), &rej);
+}
+
 static inline void l2cap_sig_channel(struct l2cap_conn *conn,
 				     struct sk_buff *skb)
 {
@@ -6426,23 +6525,25 @@
 
 		if (len > skb->len || !cmd->ident) {
 			BT_DBG("corrupted command");
-			break;
+			l2cap_sig_send_rej(conn, cmd->ident);
+			skb_pull(skb, len > skb->len ? skb->len : len);
+			continue;
 		}
 
 		err = l2cap_bredr_sig_cmd(conn, cmd, len, skb->data);
 		if (err) {
-			struct l2cap_cmd_rej_unk rej;
-
 			BT_ERR("Wrong link type (%d)", err);
-
-			rej.reason = cpu_to_le16(L2CAP_REJ_NOT_UNDERSTOOD);
-			l2cap_send_cmd(conn, cmd->ident, L2CAP_COMMAND_REJ,
-				       sizeof(rej), &rej);
+			l2cap_sig_send_rej(conn, cmd->ident);
 		}
 
 		skb_pull(skb, len);
 	}
 
+	if (skb->len > 0) {
+		BT_DBG("corrupted command");
+		l2cap_sig_send_rej(conn, 0);
+	}
+
 drop:
 	kfree_skb(skb);
 }
@@ -6842,6 +6943,7 @@
 			       struct l2cap_ctrl *control,
 			       struct sk_buff *skb, u8 event)
 {
+	struct l2cap_ctrl local_control;
 	int err = 0;
 	bool skb_in_use = false;
 
@@ -6866,15 +6968,32 @@
 			chan->buffer_seq = chan->expected_tx_seq;
 			skb_in_use = true;
 
+			/* l2cap_reassemble_sdu may free skb, hence invalidate
+			 * control, so make a copy in advance to use it after
+			 * l2cap_reassemble_sdu returns and to avoid the race
+			 * condition, for example:
+			 *
+			 * The current thread calls:
+			 *   l2cap_reassemble_sdu
+			 *     chan->ops->recv == l2cap_sock_recv_cb
+			 *       __sock_queue_rcv_skb
+			 * Another thread calls:
+			 *   bt_sock_recvmsg
+			 *     skb_recv_datagram
+			 *     skb_free_datagram
+			 * Then the current thread tries to access control, but
+			 * it was freed by skb_free_datagram.
+			 */
+			local_control = *control;
 			err = l2cap_reassemble_sdu(chan, skb, control);
 			if (err)
 				break;
 
-			if (control->final) {
+			if (local_control.final) {
 				if (!test_and_clear_bit(CONN_REJ_ACT,
 							&chan->conn_state)) {
-					control->final = 0;
-					l2cap_retransmit_all(chan, control);
+					local_control.final = 0;
+					l2cap_retransmit_all(chan, &local_control);
 					l2cap_ertm_send(chan);
 				}
 			}
@@ -7124,7 +7243,7 @@
 	if (chan->hs_hcon)
 		chan->conn->mtu = chan->hs_hcon->hdev->block_mtu;
 	else
-		chan->conn->mtu = chan->conn->hcon->hdev->acl_mtu;
+		chan->conn->mtu = chan->conn->hcon->mtu;
 
 	return l2cap_resegment(chan);
 }
@@ -7195,7 +7314,7 @@
 	if (chan->hs_hcon)
 		chan->conn->mtu = chan->hs_hcon->hdev->block_mtu;
 	else
-		chan->conn->mtu = chan->conn->hcon->hdev->acl_mtu;
+		chan->conn->mtu = chan->conn->hcon->mtu;
 
 	err = l2cap_resegment(chan);
 
@@ -7254,11 +7373,27 @@
 static int l2cap_stream_rx(struct l2cap_chan *chan, struct l2cap_ctrl *control,
 			   struct sk_buff *skb)
 {
+	/* l2cap_reassemble_sdu may free skb, hence invalidate control, so store
+	 * the txseq field in advance to use it after l2cap_reassemble_sdu
+	 * returns and to avoid the race condition, for example:
+	 *
+	 * The current thread calls:
+	 *   l2cap_reassemble_sdu
+	 *     chan->ops->recv == l2cap_sock_recv_cb
+	 *       __sock_queue_rcv_skb
+	 * Another thread calls:
+	 *   bt_sock_recvmsg
+	 *     skb_recv_datagram
+	 *     skb_free_datagram
+	 * Then the current thread tries to access control, but it was freed by
+	 * skb_free_datagram.
+	 */
+	u16 txseq = control->txseq;
+
 	BT_DBG("chan %p, control %p, skb %p, state %d", chan, control, skb,
 	       chan->rx_state);
 
-	if (l2cap_classify_txseq(chan, control->txseq) ==
-	    L2CAP_TXSEQ_EXPECTED) {
+	if (l2cap_classify_txseq(chan, txseq) == L2CAP_TXSEQ_EXPECTED) {
 		l2cap_pass_to_tx(chan, control);
 
 		BT_DBG("buffer_seq %u->%u", chan->buffer_seq,
@@ -7281,8 +7416,8 @@
 		}
 	}
 
-	chan->last_acked_seq = control->txseq;
-	chan->expected_tx_seq = __next_seq(chan, control->txseq);
+	chan->last_acked_seq = txseq;
+	chan->expected_tx_seq = __next_seq(chan, txseq);
 
 	return 0;
 }
@@ -7538,6 +7673,7 @@
 				return;
 			}
 
+			l2cap_chan_hold(chan);
 			l2cap_chan_lock(chan);
 		} else {
 			BT_DBG("unknown cid 0x%4.4x", cid);
@@ -7597,6 +7733,7 @@
 
 done:
 	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 }
 
 static void l2cap_conless_channel(struct l2cap_conn *conn, __le16 psm,
@@ -7626,6 +7763,7 @@
 	bt_cb(skb)->l2cap.psm = psm;
 
 	if (!chan->ops->recv(chan, skb)) {
+		l2cap_chan_unlock(chan);
 		l2cap_chan_put(chan);
 		return;
 	}
@@ -7728,18 +7866,7 @@
 
 	BT_DBG("hcon %p conn %p hchan %p", hcon, conn, hchan);
 
-	switch (hcon->type) {
-	case LE_LINK:
-		if (hcon->hdev->le_mtu) {
-			conn->mtu = hcon->hdev->le_mtu;
-			break;
-		}
-		fallthrough;
-	default:
-		conn->mtu = hcon->hdev->acl_mtu;
-		break;
-	}
-
+	conn->mtu = hcon->mtu;
 	conn->feat_mask = 0;
 
 	conn->local_fixed_chan = L2CAP_FC_SIG_BREDR | L2CAP_FC_CONNLESS;
@@ -8085,7 +8212,7 @@
 		if (src_type != c->src_type)
 			continue;
 
-		l2cap_chan_hold(c);
+		c = l2cap_chan_hold_unless_zero(c);
 		read_unlock(&chan_list_lock);
 		return c;
 	}
@@ -8382,9 +8509,8 @@
 		 * expected length.
 		 */
 		if (skb->len < L2CAP_LEN_SIZE) {
-			if (l2cap_recv_frag(conn, skb, conn->mtu) < 0)
-				goto drop;
-			return;
+			l2cap_recv_frag(conn, skb, conn->mtu);
+			break;
 		}
 
 		len = get_unaligned_le16(skb->data) + L2CAP_HDR_SIZE;
@@ -8428,7 +8554,7 @@
 
 			/* Header still could not be read just continue */
 			if (conn->rx_skb->len < L2CAP_LEN_SIZE)
-				return;
+				break;
 		}
 
 		if (skb->len > conn->rx_len) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/l2cap_sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/l2cap_sock.c
@@ -45,6 +45,7 @@
 static void l2cap_sock_init(struct sock *sk, struct sock *parent);
 static struct sock *l2cap_sock_alloc(struct net *net, struct socket *sock,
 				     int proto, gfp_t prio, int kern);
+static void l2cap_sock_cleanup_listen(struct sock *parent);
 
 bool l2cap_is_socket(struct socket *sock)
 {
@@ -161,7 +162,11 @@
 		break;
 	}
 
-	if (chan->psm && bdaddr_type_is_le(chan->src_type))
+	/* Use L2CAP_MODE_LE_FLOWCTL (CoC) in case of LE address and
+	 * L2CAP_MODE_EXT_FLOWCTL (ECRED) has not been set.
+	 */
+	if (chan->psm && bdaddr_type_is_le(chan->src_type) &&
+	    chan->mode != L2CAP_MODE_EXT_FLOWCTL)
 		chan->mode = L2CAP_MODE_LE_FLOWCTL;
 
 	chan->state = BT_BOUND;
@@ -172,6 +177,21 @@
 	return err;
 }
 
+static void l2cap_sock_init_pid(struct sock *sk)
+{
+	struct l2cap_chan *chan = l2cap_pi(sk)->chan;
+
+	/* Only L2CAP_MODE_EXT_FLOWCTL ever need to access the PID in order to
+	 * group the channels being requested.
+	 */
+	if (chan->mode != L2CAP_MODE_EXT_FLOWCTL)
+		return;
+
+	spin_lock(&sk->sk_peer_lock);
+	sk->sk_peer_pid = get_pid(task_tgid(current));
+	spin_unlock(&sk->sk_peer_lock);
+}
+
 static int l2cap_sock_connect(struct socket *sock, struct sockaddr *addr,
 			      int alen, int flags)
 {
@@ -240,9 +260,15 @@
 			return -EINVAL;
 	}
 
-	if (chan->psm && bdaddr_type_is_le(chan->src_type) && !chan->mode)
+	/* Use L2CAP_MODE_LE_FLOWCTL (CoC) in case of LE address and
+	 * L2CAP_MODE_EXT_FLOWCTL (ECRED) has not been set.
+	 */
+	if (chan->psm && bdaddr_type_is_le(chan->src_type) &&
+	    chan->mode != L2CAP_MODE_EXT_FLOWCTL)
 		chan->mode = L2CAP_MODE_LE_FLOWCTL;
 
+	l2cap_sock_init_pid(sk);
+
 	err = l2cap_chan_connect(chan, la.l2_psm, __le16_to_cpu(la.l2_cid),
 				 &la.l2_bdaddr, la.l2_bdaddr_type);
 	if (err)
@@ -298,6 +324,8 @@
 		goto done;
 	}
 
+	l2cap_sock_init_pid(sk);
+
 	sk->sk_max_ack_backlog = backlog;
 	sk->sk_ack_backlog = 0;
 
@@ -428,7 +456,8 @@
 	struct l2cap_chan *chan = l2cap_pi(sk)->chan;
 	struct l2cap_options opts;
 	struct l2cap_conninfo cinfo;
-	int len, err = 0;
+	int err = 0;
+	size_t len;
 	u32 opt;
 
 	BT_DBG("sk %p", sk);
@@ -475,7 +504,7 @@
 
 		BT_DBG("mode 0x%2.2x", chan->mode);
 
-		len = min_t(unsigned int, len, sizeof(opts));
+		len = min(len, sizeof(opts));
 		if (copy_to_user(optval, (char *) &opts, len))
 			err = -EFAULT;
 
@@ -525,7 +554,7 @@
 		cinfo.hci_handle = chan->conn->hcon->handle;
 		memcpy(cinfo.dev_class, chan->conn->hcon->dev_class, 3);
 
-		len = min_t(unsigned int, len, sizeof(cinfo));
+		len = min(len, sizeof(cinfo));
 		if (copy_to_user(optval, (char *) &cinfo, len))
 			err = -EFAULT;
 
@@ -698,12 +727,12 @@
 {
 	switch (chan->scid) {
 	case L2CAP_CID_ATT:
-		if (mtu < L2CAP_LE_MIN_MTU)
+		if (mtu && mtu < L2CAP_LE_MIN_MTU)
 			return false;
 		break;
 
 	default:
-		if (mtu < L2CAP_DEFAULT_MIN_MTU)
+		if (mtu && mtu < L2CAP_DEFAULT_MIN_MTU)
 			return false;
 	}
 
@@ -716,7 +745,7 @@
 	struct sock *sk = sock->sk;
 	struct l2cap_chan *chan = l2cap_pi(sk)->chan;
 	struct l2cap_options opts;
-	int len, err = 0;
+	int err = 0;
 	u32 opt;
 
 	BT_DBG("sk %p", sk);
@@ -743,11 +772,9 @@
 		opts.max_tx   = chan->max_tx;
 		opts.txwin_size = chan->tx_win;
 
-		len = min_t(unsigned int, sizeof(opts), optlen);
-		if (copy_from_sockptr(&opts, optval, len)) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opts, sizeof(opts), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opts.txwin_size > L2CAP_DEFAULT_EXT_WINDOW) {
 			err = -EINVAL;
@@ -790,10 +817,9 @@
 		break;
 
 	case L2CAP_LM:
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt & L2CAP_LM_FIPS) {
 			err = -EINVAL;
@@ -874,8 +900,10 @@
 	struct bt_security sec;
 	struct bt_power pwr;
 	struct l2cap_conn *conn;
-	int len, err = 0;
+	int err = 0;
 	u32 opt;
+	u16 mtu;
+	u8 mode;
 
 	BT_DBG("sk %p", sk);
 
@@ -898,11 +926,9 @@
 
 		sec.level = BT_SECURITY_LOW;
 
-		len = min_t(unsigned int, sizeof(sec), optlen);
-		if (copy_from_sockptr(&sec, optval, len)) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&sec, sizeof(sec), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (sec.level < BT_SECURITY_LOW ||
 		    sec.level > BT_SECURITY_FIPS) {
@@ -947,10 +973,9 @@
 			break;
 		}
 
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt) {
 			set_bit(BT_SK_DEFER_SETUP, &bt_sk(sk)->flags);
@@ -962,10 +987,9 @@
 		break;
 
 	case BT_FLUSHABLE:
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt > BT_FLUSHABLE_ON) {
 			err = -EINVAL;
@@ -997,11 +1021,9 @@
 
 		pwr.force_active = BT_POWER_FORCE_ACTIVE_ON;
 
-		len = min_t(unsigned int, sizeof(pwr), optlen);
-		if (copy_from_sockptr(&pwr, optval, len)) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&pwr, sizeof(pwr), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (pwr.force_active)
 			set_bit(FLAG_FORCE_ACTIVE, &chan->flags);
@@ -1010,10 +1032,9 @@
 		break;
 
 	case BT_CHANNEL_POLICY:
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt > BT_CHANNEL_POLICY_AMP_PREFERRED) {
 			err = -EINVAL;
@@ -1058,16 +1079,15 @@
 			break;
 		}
 
-		if (copy_from_sockptr(&opt, optval, sizeof(u16))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&mtu, sizeof(mtu), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (chan->mode == L2CAP_MODE_EXT_FLOWCTL &&
 		    sk->sk_state == BT_CONNECTED)
-			err = l2cap_chan_reconfigure(chan, opt);
+			err = l2cap_chan_reconfigure(chan, mtu);
 		else
-			chan->imtu = opt;
+			chan->imtu = mtu;
 
 		break;
 
@@ -1089,14 +1109,13 @@
 			break;
 		}
 
-		if (copy_from_sockptr(&opt, optval, sizeof(u8))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&mode, sizeof(mode), optval, optlen);
+		if (err)
 			break;
-		}
 
-		BT_DBG("opt %u", opt);
+		BT_DBG("mode %u", mode);
 
-		err = l2cap_set_mode(chan, opt);
+		err = l2cap_set_mode(chan, mode);
 		if (err)
 			break;
 
@@ -1385,6 +1404,7 @@
 	if (!sk)
 		return 0;
 
+	l2cap_sock_cleanup_listen(sk);
 	bt_sock_unlink(&l2cap_sk_list, sk);
 
 	err = l2cap_sock_shutdown(sock, SHUT_RDWR);
@@ -1508,6 +1528,9 @@
 {
 	struct sock *sk = chan->data;
 
+	if (!sk)
+		return;
+
 	l2cap_sock_kill(sk);
 }
 
@@ -1516,6 +1539,9 @@
 	struct sock *sk = chan->data;
 	struct sock *parent;
 
+	if (!sk)
+		return;
+
 	BT_DBG("chan %p state %s", chan, state_to_string(chan->state));
 
 	/* This callback can be called both for server (BT_LISTEN)
@@ -1588,6 +1614,14 @@
 	if (!skb)
 		return ERR_PTR(err);
 
+	/* Channel lock is released before requesting new skb and then
+	 * reacquired thus we need to recheck channel state.
+	 */
+	if (chan->state != BT_CONNECTED) {
+		kfree_skb(skb);
+		return ERR_PTR(-ENOTCONN);
+	}
+
 	skb->priority = sk->sk_priority;
 
 	bt_cb(skb)->l2cap.chan = chan;
@@ -1707,8 +1741,10 @@
 {
 	BT_DBG("sk %p", sk);
 
-	if (l2cap_pi(sk)->chan)
+	if (l2cap_pi(sk)->chan) {
+		l2cap_pi(sk)->chan->data = NULL;
 		l2cap_chan_put(l2cap_pi(sk)->chan);
+	}
 
 	if (l2cap_pi(sk)->rx_busy_skb) {
 		kfree_skb(l2cap_pi(sk)->rx_busy_skb);
@@ -1828,6 +1864,8 @@
 	chan = l2cap_chan_create();
 	if (!chan) {
 		sk_free(sk);
+		if (sock)
+			sock->sk = NULL;
 		return NULL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/mgmt.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/mgmt.c
@@ -2375,15 +2375,6 @@
 	bt_dev_dbg(hdev, "debug_keys %u key_count %u", cp->debug_keys,
 		   key_count);
 
-	for (i = 0; i < key_count; i++) {
-		struct mgmt_link_key_info *key = &cp->keys[i];
-
-		if (key->addr.type != BDADDR_BREDR || key->type > 0x08)
-			return mgmt_cmd_status(sk, hdev->id,
-					       MGMT_OP_LOAD_LINK_KEYS,
-					       MGMT_STATUS_INVALID_PARAMS);
-	}
-
 	hci_dev_lock(hdev);
 
 	hci_link_keys_clear(hdev);
@@ -2408,6 +2399,19 @@
 			continue;
 		}
 
+		if (key->addr.type != BDADDR_BREDR) {
+			bt_dev_warn(hdev,
+				    "Invalid link address type %u for %pMR",
+				    key->addr.type, &key->addr.bdaddr);
+			continue;
+		}
+
+		if (key->type > 0x08) {
+			bt_dev_warn(hdev, "Invalid link key type %u for %pMR",
+				    key->type, &key->addr.bdaddr);
+			continue;
+		}
+
 		/* Always ignore debug keys and require a new pairing if
 		 * the user wants to use them.
 		 */
@@ -2966,6 +2970,10 @@
 		 * will be kept and this function does nothing.
 		 */
 		p = hci_conn_params_add(hdev, &cp->addr.bdaddr, addr_type);
+		if (!p) {
+			err = -EIO;
+			goto unlock;
+		}
 
 		if (p->auto_connect == HCI_AUTO_CONN_EXPLICIT)
 			p->auto_connect = HCI_AUTO_CONN_DISABLED;
@@ -3806,7 +3814,7 @@
 static int read_exp_features_info(struct sock *sk, struct hci_dev *hdev,
 				  void *data, u16 data_len)
 {
-	char buf[62];	/* Enough space for 3 features */
+	char buf[62];   /* Enough space for 3 features */
 	struct mgmt_rp_read_exp_features_info *rp = (void *)buf;
 	u16 idx = 0;
 	u32 flags;
@@ -3892,150 +3900,186 @@
 }
 #endif
 
-static int set_exp_feature(struct sock *sk, struct hci_dev *hdev,
-			   void *data, u16 data_len)
+#define EXP_FEAT(_uuid, _set_func)	\
+{					\
+	.uuid = _uuid,			\
+	.set_func = _set_func,		\
+}
+
+/* The zero key uuid is special. Multiple exp features are set through it. */
+static int set_zero_key_func(struct sock *sk, struct hci_dev *hdev,
+			     struct mgmt_cp_set_exp_feature *cp, u16 data_len)
 {
-	struct mgmt_cp_set_exp_feature *cp = data;
 	struct mgmt_rp_set_exp_feature rp;
 
-	bt_dev_dbg(hdev, "sock %p", sk);
-
-	if (!memcmp(cp->uuid, ZERO_KEY, 16)) {
-		memset(rp.uuid, 0, 16);
-		rp.flags = cpu_to_le32(0);
+	memset(rp.uuid, 0, 16);
+	rp.flags = cpu_to_le32(0);
 
 #ifdef CONFIG_BT_FEATURE_DEBUG
-		if (!hdev) {
-			bool changed = bt_dbg_get();
+	if (!hdev) {
+		bool changed = bt_dbg_get();
 
-			bt_dbg_set(false);
+		bt_dbg_set(false);
 
-			if (changed)
-				exp_debug_feature_changed(false, sk);
-		}
+		if (changed)
+			exp_debug_feature_changed(false, sk);
+	}
 #endif
 
-		if (hdev && use_ll_privacy(hdev) && !hdev_is_powered(hdev)) {
-			bool changed = hci_dev_test_flag(hdev,
-							 HCI_ENABLE_LL_PRIVACY);
-
-			hci_dev_clear_flag(hdev, HCI_ENABLE_LL_PRIVACY);
+	if (hdev && use_ll_privacy(hdev) && !hdev_is_powered(hdev)) {
+		bool changed;
 
-			if (changed)
-				exp_ll_privacy_feature_changed(false, hdev, sk);
-		}
+		changed = hci_dev_test_and_clear_flag(hdev,
+						      HCI_ENABLE_LL_PRIVACY);
+		if (changed)
+			exp_ll_privacy_feature_changed(false, hdev, sk);
+	}
 
-		hci_sock_set_flag(sk, HCI_MGMT_EXP_FEATURE_EVENTS);
+	hci_sock_set_flag(sk, HCI_MGMT_EXP_FEATURE_EVENTS);
 
-		return mgmt_cmd_complete(sk, hdev ? hdev->id : MGMT_INDEX_NONE,
-					 MGMT_OP_SET_EXP_FEATURE, 0,
-					 &rp, sizeof(rp));
-	}
+	return mgmt_cmd_complete(sk, hdev ? hdev->id : MGMT_INDEX_NONE,
+				 MGMT_OP_SET_EXP_FEATURE, 0,
+				 &rp, sizeof(rp));
+}
 
 #ifdef CONFIG_BT_FEATURE_DEBUG
-	if (!memcmp(cp->uuid, debug_uuid, 16)) {
-		bool val, changed;
-		int err;
+static int set_debug_func(struct sock *sk, struct hci_dev *hdev,
+			  struct mgmt_cp_set_exp_feature *cp, u16 data_len)
+{
+	struct mgmt_rp_set_exp_feature rp;
 
-		/* Command requires to use the non-controller index */
-		if (hdev)
-			return mgmt_cmd_status(sk, hdev->id,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_INVALID_INDEX);
+	bool val, changed;
+	int err;
 
-		/* Parameters are limited to a single octet */
-		if (data_len != MGMT_SET_EXP_FEATURE_SIZE + 1)
-			return mgmt_cmd_status(sk, MGMT_INDEX_NONE,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_INVALID_PARAMS);
+	/* Command requires to use the non-controller index */
+	if (hdev)
+		return mgmt_cmd_status(sk, hdev->id,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_INVALID_INDEX);
 
-		/* Only boolean on/off is supported */
-		if (cp->param[0] != 0x00 && cp->param[0] != 0x01)
-			return mgmt_cmd_status(sk, MGMT_INDEX_NONE,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_INVALID_PARAMS);
+	/* Parameters are limited to a single octet */
+	if (data_len != MGMT_SET_EXP_FEATURE_SIZE + 1)
+		return mgmt_cmd_status(sk, MGMT_INDEX_NONE,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_INVALID_PARAMS);
 
-		val = !!cp->param[0];
-		changed = val ? !bt_dbg_get() : bt_dbg_get();
-		bt_dbg_set(val);
+	/* Only boolean on/off is supported */
+	if (cp->param[0] != 0x00 && cp->param[0] != 0x01)
+		return mgmt_cmd_status(sk, MGMT_INDEX_NONE,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_INVALID_PARAMS);
 
-		memcpy(rp.uuid, debug_uuid, 16);
-		rp.flags = cpu_to_le32(val ? BIT(0) : 0);
+	val = !!cp->param[0];
+	changed = val ? !bt_dbg_get() : bt_dbg_get();
+	bt_dbg_set(val);
 
-		hci_sock_set_flag(sk, HCI_MGMT_EXP_FEATURE_EVENTS);
+	memcpy(rp.uuid, debug_uuid, 16);
+	rp.flags = cpu_to_le32(val ? BIT(0) : 0);
 
-		err = mgmt_cmd_complete(sk, MGMT_INDEX_NONE,
-					MGMT_OP_SET_EXP_FEATURE, 0,
-					&rp, sizeof(rp));
+	hci_sock_set_flag(sk, HCI_MGMT_EXP_FEATURE_EVENTS);
 
-		if (changed)
-			exp_debug_feature_changed(val, sk);
+	err = mgmt_cmd_complete(sk, MGMT_INDEX_NONE,
+				MGMT_OP_SET_EXP_FEATURE, 0,
+				&rp, sizeof(rp));
 
-		return err;
-	}
+	if (changed)
+		exp_debug_feature_changed(val, sk);
+
+	return err;
+}
 #endif
 
-	if (!memcmp(cp->uuid, rpa_resolution_uuid, 16)) {
-		bool val, changed;
-		int err;
-		u32 flags;
-
-		/* Command requires to use the controller index */
-		if (!hdev)
-			return mgmt_cmd_status(sk, MGMT_INDEX_NONE,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_INVALID_INDEX);
+static int set_rpa_resolution_func(struct sock *sk, struct hci_dev *hdev,
+				   struct mgmt_cp_set_exp_feature *cp,
+				   u16 data_len)
+{
+	struct mgmt_rp_set_exp_feature rp;
+	bool val, changed;
+	int err;
+	u32 flags;
+
+	/* Command requires to use the controller index */
+	if (!hdev)
+		return mgmt_cmd_status(sk, MGMT_INDEX_NONE,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_INVALID_INDEX);
 
-		/* Changes can only be made when controller is powered down */
-		if (hdev_is_powered(hdev))
-			return mgmt_cmd_status(sk, hdev->id,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_REJECTED);
+	/* Changes can only be made when controller is powered down */
+	if (hdev_is_powered(hdev))
+		return mgmt_cmd_status(sk, hdev->id,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_REJECTED);
 
-		/* Parameters are limited to a single octet */
-		if (data_len != MGMT_SET_EXP_FEATURE_SIZE + 1)
-			return mgmt_cmd_status(sk, hdev->id,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_INVALID_PARAMS);
+	/* Parameters are limited to a single octet */
+	if (data_len != MGMT_SET_EXP_FEATURE_SIZE + 1)
+		return mgmt_cmd_status(sk, hdev->id,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_INVALID_PARAMS);
 
-		/* Only boolean on/off is supported */
-		if (cp->param[0] != 0x00 && cp->param[0] != 0x01)
-			return mgmt_cmd_status(sk, hdev->id,
-					       MGMT_OP_SET_EXP_FEATURE,
-					       MGMT_STATUS_INVALID_PARAMS);
+	/* Only boolean on/off is supported */
+	if (cp->param[0] != 0x00 && cp->param[0] != 0x01)
+		return mgmt_cmd_status(sk, hdev->id,
+				       MGMT_OP_SET_EXP_FEATURE,
+				       MGMT_STATUS_INVALID_PARAMS);
 
-		val = !!cp->param[0];
+	val = !!cp->param[0];
 
-		if (val) {
-			changed = !hci_dev_test_flag(hdev,
+	if (val) {
+		changed = !hci_dev_test_and_set_flag(hdev,
 						     HCI_ENABLE_LL_PRIVACY);
-			hci_dev_set_flag(hdev, HCI_ENABLE_LL_PRIVACY);
-			hci_dev_clear_flag(hdev, HCI_ADVERTISING);
+		hci_dev_clear_flag(hdev, HCI_ADVERTISING);
 
-			/* Enable LL privacy + supported settings changed */
-			flags = BIT(0) | BIT(1);
-		} else {
-			changed = hci_dev_test_flag(hdev,
-						    HCI_ENABLE_LL_PRIVACY);
-			hci_dev_clear_flag(hdev, HCI_ENABLE_LL_PRIVACY);
+		/* Enable LL privacy + supported settings changed */
+		flags = BIT(0) | BIT(1);
+	} else {
+		changed = hci_dev_test_and_clear_flag(hdev,
+						      HCI_ENABLE_LL_PRIVACY);
 
-			/* Disable LL privacy + supported settings changed */
-			flags = BIT(1);
-		}
+		/* Disable LL privacy + supported settings changed */
+		flags = BIT(1);
+	}
 
-		memcpy(rp.uuid, rpa_resolution_uuid, 16);
-		rp.flags = cpu_to_le32(flags);
+	memcpy(rp.uuid, rpa_resolution_uuid, 16);
+	rp.flags = cpu_to_le32(flags);
 
-		hci_sock_set_flag(sk, HCI_MGMT_EXP_FEATURE_EVENTS);
+	hci_sock_set_flag(sk, HCI_MGMT_EXP_FEATURE_EVENTS);
 
-		err = mgmt_cmd_complete(sk, hdev->id,
-					MGMT_OP_SET_EXP_FEATURE, 0,
-					&rp, sizeof(rp));
+	err = mgmt_cmd_complete(sk, hdev->id,
+				MGMT_OP_SET_EXP_FEATURE, 0,
+				&rp, sizeof(rp));
 
-		if (changed)
-			exp_ll_privacy_feature_changed(val, hdev, sk);
+	if (changed)
+		exp_ll_privacy_feature_changed(val, hdev, sk);
 
-		return err;
+	return err;
+}
+
+static const struct mgmt_exp_feature {
+	const u8 *uuid;
+	int (*set_func)(struct sock *sk, struct hci_dev *hdev,
+			struct mgmt_cp_set_exp_feature *cp, u16 data_len);
+} exp_features[] = {
+	EXP_FEAT(ZERO_KEY, set_zero_key_func),
+#ifdef CONFIG_BT_FEATURE_DEBUG
+	EXP_FEAT(debug_uuid, set_debug_func),
+#endif
+	EXP_FEAT(rpa_resolution_uuid, set_rpa_resolution_func),
+
+	/* end with a null feature */
+	EXP_FEAT(NULL, NULL)
+};
+
+static int set_exp_feature(struct sock *sk, struct hci_dev *hdev,
+			   void *data, u16 data_len)
+{
+	struct mgmt_cp_set_exp_feature *cp = data;
+	size_t i = 0;
+
+	bt_dev_dbg(hdev, "sock %p", sk);
+
+	for (i = 0; exp_features[i].uuid; i++) {
+		if (!memcmp(cp->uuid, exp_features[i].uuid, 16))
+			return exp_features[i].set_func(sk, hdev, cp, data_len);
 	}
 
 	return mgmt_cmd_status(sk, hdev ? hdev->id : MGMT_INDEX_NONE,
@@ -6219,15 +6263,6 @@
 
 	bt_dev_dbg(hdev, "key_count %u", key_count);
 
-	for (i = 0; i < key_count; i++) {
-		struct mgmt_ltk_info *key = &cp->keys[i];
-
-		if (!ltk_is_valid(key))
-			return mgmt_cmd_status(sk, hdev->id,
-					       MGMT_OP_LOAD_LONG_TERM_KEYS,
-					       MGMT_STATUS_INVALID_PARAMS);
-	}
-
 	hci_dev_lock(hdev);
 
 	hci_smp_ltks_clear(hdev);
@@ -6244,6 +6279,12 @@
 			continue;
 		}
 
+		if (!ltk_is_valid(key)) {
+			bt_dev_warn(hdev, "Invalid LTK for %pMR",
+				    &key->addr.bdaddr);
+			continue;
+		}
+
 		switch (key->type) {
 		case MGMT_LTK_UNAUTHENTICATED:
 			authenticated = 0x00;
@@ -7935,7 +7976,7 @@
 	 * extra parameters we don't know about will be ignored in this request.
 	 */
 	if (data_len < MGMT_ADD_EXT_ADV_PARAMS_MIN_SIZE)
-		return mgmt_cmd_status(sk, hdev->id, MGMT_OP_ADD_ADVERTISING,
+		return mgmt_cmd_status(sk, hdev->id, MGMT_OP_ADD_EXT_ADV_PARAMS,
 				       MGMT_STATUS_INVALID_PARAMS);
 
 	flags = __le32_to_cpu(cp->flags);
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/rfcomm/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/rfcomm/core.c
@@ -549,22 +549,58 @@
 	return dlc;
 }
 
+static int rfcomm_dlc_send_frag(struct rfcomm_dlc *d, struct sk_buff *frag)
+{
+	int len = frag->len;
+
+	BT_DBG("dlc %p mtu %d len %d", d, d->mtu, len);
+
+	if (len > d->mtu)
+		return -EINVAL;
+
+	rfcomm_make_uih(frag, d->addr);
+	__skb_queue_tail(&d->tx_queue, frag);
+
+	return len;
+}
+
 int rfcomm_dlc_send(struct rfcomm_dlc *d, struct sk_buff *skb)
 {
-	int len = skb->len;
+	unsigned long flags;
+	struct sk_buff *frag, *next;
+	int len;
 
 	if (d->state != BT_CONNECTED)
 		return -ENOTCONN;
 
-	BT_DBG("dlc %p mtu %d len %d", d, d->mtu, len);
+	frag = skb_shinfo(skb)->frag_list;
+	skb_shinfo(skb)->frag_list = NULL;
 
-	if (len > d->mtu)
-		return -EINVAL;
+	/* Queue all fragments atomically. */
+	spin_lock_irqsave(&d->tx_queue.lock, flags);
 
-	rfcomm_make_uih(skb, d->addr);
-	skb_queue_tail(&d->tx_queue, skb);
+	len = rfcomm_dlc_send_frag(d, skb);
+	if (len < 0 || !frag)
+		goto unlock;
+
+	for (; frag; frag = next) {
+		int ret;
+
+		next = frag->next;
+
+		ret = rfcomm_dlc_send_frag(d, frag);
+		if (ret < 0) {
+			dev_kfree_skb_irq(frag);
+			goto unlock;
+		}
+
+		len += ret;
+	}
+
+unlock:
+	spin_unlock_irqrestore(&d->tx_queue.lock, flags);
 
-	if (!test_bit(RFCOMM_TX_THROTTLED, &d->flags))
+	if (len > 0 && !test_bit(RFCOMM_TX_THROTTLED, &d->flags))
 		rfcomm_schedule();
 	return len;
 }
@@ -1901,7 +1937,7 @@
 	/* Get data directly from socket receive queue without copying it. */
 	while ((skb = skb_dequeue(&sk->sk_receive_queue))) {
 		skb_orphan(skb);
-		if (!skb_linearize(skb)) {
+		if (!skb_linearize(skb) && sk->sk_state != BT_CLOSED) {
 			s = rfcomm_recv_frame(s, skb);
 			if (!s)
 				break;
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/rfcomm/sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/rfcomm/sock.c
@@ -391,6 +391,7 @@
 	    addr->sa_family != AF_BLUETOOTH)
 		return -EINVAL;
 
+	sock_hold(sk);
 	lock_sock(sk);
 
 	if (sk->sk_state != BT_OPEN && sk->sk_state != BT_BOUND) {
@@ -410,14 +411,18 @@
 	d->sec_level = rfcomm_pi(sk)->sec_level;
 	d->role_switch = rfcomm_pi(sk)->role_switch;
 
+	/* Drop sock lock to avoid potential deadlock with the RFCOMM lock */
+	release_sock(sk);
 	err = rfcomm_dlc_open(d, &rfcomm_pi(sk)->src, &sa->rc_bdaddr,
 			      sa->rc_channel);
-	if (!err)
+	lock_sock(sk);
+	if (!err && !sock_flag(sk, SOCK_ZAPPED))
 		err = bt_sock_wait_state(sk, BT_CONNECTED,
 				sock_sndtimeo(sk, flags & O_NONBLOCK));
 
 done:
 	release_sock(sk);
+	sock_put(sk);
 	return err;
 }
 
@@ -575,46 +580,20 @@
 	lock_sock(sk);
 
 	sent = bt_sock_wait_ready(sk, msg->msg_flags);
-	if (sent)
-		goto done;
-
-	while (len) {
-		size_t size = min_t(size_t, len, d->mtu);
-		int err;
 
-		skb = sock_alloc_send_skb(sk, size + RFCOMM_SKB_RESERVE,
-				msg->msg_flags & MSG_DONTWAIT, &err);
-		if (!skb) {
-			if (sent == 0)
-				sent = err;
-			break;
-		}
-		skb_reserve(skb, RFCOMM_SKB_HEAD_RESERVE);
-
-		err = memcpy_from_msg(skb_put(skb, size), msg, size);
-		if (err) {
-			kfree_skb(skb);
-			if (sent == 0)
-				sent = err;
-			break;
-		}
-
-		skb->priority = sk->sk_priority;
+	release_sock(sk);
 
-		err = rfcomm_dlc_send(d, skb);
-		if (err < 0) {
-			kfree_skb(skb);
-			if (sent == 0)
-				sent = err;
-			break;
-		}
+	if (sent)
+		return sent;
 
-		sent += size;
-		len  -= size;
-	}
-
-done:
-	release_sock(sk);
+	skb = bt_skb_sendmmsg(sk, msg, len, d->mtu, RFCOMM_SKB_HEAD_RESERVE,
+			      RFCOMM_SKB_TAIL_RESERVE);
+	if (IS_ERR(skb))
+		return PTR_ERR(skb);
+
+	sent = rfcomm_dlc_send(d, skb);
+	if (sent < 0)
+		kfree_skb(skb);
 
 	return sent;
 }
@@ -657,7 +636,7 @@
 
 	switch (optname) {
 	case RFCOMM_LM:
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
+		if (bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen)) {
 			err = -EFAULT;
 			break;
 		}
@@ -692,7 +671,6 @@
 	struct sock *sk = sock->sk;
 	struct bt_security sec;
 	int err = 0;
-	size_t len;
 	u32 opt;
 
 	BT_DBG("sk %p", sk);
@@ -714,11 +692,9 @@
 
 		sec.level = BT_SECURITY_LOW;
 
-		len = min_t(unsigned int, sizeof(sec), optlen);
-		if (copy_from_sockptr(&sec, optval, len)) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&sec, sizeof(sec), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (sec.level > BT_SECURITY_HIGH) {
 			err = -EINVAL;
@@ -734,10 +710,9 @@
 			break;
 		}
 
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt)
 			set_bit(BT_SK_DEFER_SETUP, &bt_sk(sk)->flags);
@@ -761,7 +736,8 @@
 	struct sock *l2cap_sk;
 	struct l2cap_conn *conn;
 	struct rfcomm_conninfo cinfo;
-	int len, err = 0;
+	int err = 0;
+	size_t len;
 	u32 opt;
 
 	BT_DBG("sk %p", sk);
@@ -815,7 +791,7 @@
 		cinfo.hci_handle = conn->hcon->handle;
 		memcpy(cinfo.dev_class, conn->hcon->dev_class, 3);
 
-		len = min_t(unsigned int, len, sizeof(cinfo));
+		len = min(len, sizeof(cinfo));
 		if (copy_to_user(optval, (char *) &cinfo, len))
 			err = -EFAULT;
 
@@ -834,7 +810,8 @@
 {
 	struct sock *sk = sock->sk;
 	struct bt_security sec;
-	int len, err = 0;
+	int err = 0;
+	size_t len;
 
 	BT_DBG("sk %p", sk);
 
@@ -859,7 +836,7 @@
 		sec.level = rfcomm_pi(sk)->sec_level;
 		sec.key_size = 0;
 
-		len = min_t(unsigned int, len, sizeof(sec));
+		len = min(len, sizeof(sec));
 		if (copy_to_user(optval, (char *) &sec, len))
 			err = -EFAULT;
 
@@ -897,9 +874,7 @@
 
 	if (err == -ENOIOCTLCMD) {
 #ifdef CONFIG_BT_RFCOMM_TTY
-		lock_sock(sk);
 		err = rfcomm_dev_ioctl(sk, cmd, (void __user *) arg);
-		release_sock(sk);
 #else
 		err = -EOPNOTSUPP;
 #endif
@@ -928,7 +903,10 @@
 	lock_sock(sk);
 	if (!sk->sk_shutdown) {
 		sk->sk_shutdown = SHUTDOWN_MASK;
+
+		release_sock(sk);
 		__rfcomm_sock_close(sk);
+		lock_sock(sk);
 
 		if (sock_flag(sk, SOCK_LINGER) && sk->sk_lingertime &&
 		    !(current->flags & PF_EXITING))
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/sco.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/sco.c
@@ -83,6 +83,10 @@
 	struct sock *sk;
 
 	sco_conn_lock(conn);
+	if (!conn->hcon) {
+		sco_conn_unlock(conn);
+		return;
+	}
 	sk = conn->sk;
 	if (sk)
 		sock_hold(sk);
@@ -122,7 +126,6 @@
 /* ---- SCO connections ---- */
 static struct sco_conn *sco_conn_add(struct hci_conn *hcon)
 {
-	struct hci_dev *hdev = hcon->hdev;
 	struct sco_conn *conn = hcon->sco_data;
 
 	if (conn)
@@ -133,12 +136,14 @@
 		return NULL;
 
 	spin_lock_init(&conn->lock);
+	INIT_DELAYED_WORK(&conn->timeout_work, sco_sock_timeout);
 
 	hcon->sco_data = conn;
 	conn->hcon = hcon;
+	conn->mtu = hcon->mtu;
 
-	if (hdev->sco_mtu > 0)
-		conn->mtu = hdev->sco_mtu;
+	if (hcon->mtu > 0)
+		conn->mtu = hcon->mtu;
 	else
 		conn->mtu = 60;
 
@@ -187,20 +192,21 @@
 	/* Kill socket */
 	sco_conn_lock(conn);
 	sk = conn->sk;
+	if (sk)
+		sock_hold(sk);
 	sco_conn_unlock(conn);
 
 	if (sk) {
-		sock_hold(sk);
 		lock_sock(sk);
 		sco_sock_clear_timer(sk);
 		sco_chan_del(sk, err);
 		release_sock(sk);
 		sock_put(sk);
-
-		/* Ensure no more work items will run before freeing conn. */
-		cancel_delayed_work_sync(&conn->timeout_work);
 	}
 
+	/* Ensure no more work items will run before freeing conn. */
+	cancel_delayed_work_sync(&conn->timeout_work);
+
 	hcon->sco_data = NULL;
 	kfree(conn);
 }
@@ -213,8 +219,6 @@
 	sco_pi(sk)->conn = conn;
 	conn->sk = sk;
 
-	INIT_DELAYED_WORK(&conn->timeout_work, sco_sock_timeout);
-
 	if (parent)
 		bt_accept_enqueue(parent, sk, true);
 }
@@ -280,11 +284,10 @@
 	return err;
 }
 
-static int sco_send_frame(struct sock *sk, struct msghdr *msg, int len)
+static int sco_send_frame(struct sock *sk, struct sk_buff *skb)
 {
 	struct sco_conn *conn = sco_pi(sk)->conn;
-	struct sk_buff *skb;
-	int err;
+	int len = skb->len;
 
 	/* Check outgoing MTU */
 	if (len > conn->mtu)
@@ -292,15 +295,6 @@
 
 	BT_DBG("sk %p len %d", sk, len);
 
-	skb = bt_skb_send_alloc(sk, len, msg->msg_flags & MSG_DONTWAIT, &err);
-	if (!skb)
-		return err;
-
-	if (memcpy_from_msg(skb_put(skb, len), msg, len)) {
-		kfree_skb(skb);
-		return -EFAULT;
-	}
-
 	hci_send_sco(conn->hcon, skb);
 
 	return len;
@@ -578,19 +572,24 @@
 	    addr->sa_family != AF_BLUETOOTH)
 		return -EINVAL;
 
-	if (sk->sk_state != BT_OPEN && sk->sk_state != BT_BOUND)
-		return -EBADFD;
+	lock_sock(sk);
+	if (sk->sk_state != BT_OPEN && sk->sk_state != BT_BOUND) {
+		err = -EBADFD;
+		goto done;
+	}
 
-	if (sk->sk_type != SOCK_SEQPACKET)
-		return -EINVAL;
+	if (sk->sk_type != SOCK_SEQPACKET) {
+		err = -EINVAL;
+		goto done;
+	}
 
 	hdev = hci_get_route(&sa->sco_bdaddr, &sco_pi(sk)->src, BDADDR_BREDR);
-	if (!hdev)
-		return -EHOSTUNREACH;
+	if (!hdev) {
+		err = -EHOSTUNREACH;
+		goto done;
+	}
 	hci_dev_lock(hdev);
 
-	lock_sock(sk);
-
 	/* Set destination address and psm */
 	bacpy(&sco_pi(sk)->dst, &sa->sco_bdaddr);
 
@@ -725,6 +724,7 @@
 			    size_t len)
 {
 	struct sock *sk = sock->sk;
+	struct sk_buff *skb;
 	int err;
 
 	BT_DBG("sock %p, sk %p", sock, sk);
@@ -736,14 +736,21 @@
 	if (msg->msg_flags & MSG_OOB)
 		return -EOPNOTSUPP;
 
+	skb = bt_skb_sendmsg(sk, msg, len, len, 0, 0);
+	if (IS_ERR(skb))
+		return PTR_ERR(skb);
+
 	lock_sock(sk);
 
 	if (sk->sk_state == BT_CONNECTED)
-		err = sco_send_frame(sk, msg, len);
+		err = sco_send_frame(sk, skb);
 	else
 		err = -ENOTCONN;
 
 	release_sock(sk);
+
+	if (err < 0)
+		kfree_skb(skb);
 	return err;
 }
 
@@ -822,7 +829,7 @@
 			       sockptr_t optval, unsigned int optlen)
 {
 	struct sock *sk = sock->sk;
-	int len, err = 0;
+	int err = 0;
 	struct bt_voice voice;
 	u32 opt;
 
@@ -838,10 +845,9 @@
 			break;
 		}
 
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt)
 			set_bit(BT_SK_DEFER_SETUP, &bt_sk(sk)->flags);
@@ -858,11 +864,10 @@
 
 		voice.setting = sco_pi(sk)->setting;
 
-		len = min_t(unsigned int, sizeof(voice), optlen);
-		if (copy_from_sockptr(&voice, optval, len)) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&voice, sizeof(voice), optval,
+					   optlen);
+		if (err)
 			break;
-		}
 
 		/* Explicitly check for these values */
 		if (voice.setting != BT_VOICE_TRANSPARENT &&
@@ -875,10 +880,9 @@
 		break;
 
 	case BT_PKT_STATUS:
-		if (copy_from_sockptr(&opt, optval, sizeof(u32))) {
-			err = -EFAULT;
+		err = bt_copy_from_sockptr(&opt, sizeof(opt), optval, optlen);
+		if (err)
 			break;
-		}
 
 		if (opt)
 			sco_pi(sk)->cmsg_mask |= SCO_CMSG_PKT_STATUS;
@@ -901,7 +905,8 @@
 	struct sock *sk = sock->sk;
 	struct sco_options opts;
 	struct sco_conninfo cinfo;
-	int len, err = 0;
+	int err = 0;
+	size_t len;
 
 	BT_DBG("sk %p", sk);
 
@@ -923,7 +928,7 @@
 
 		BT_DBG("mtu %u", opts.mtu);
 
-		len = min_t(unsigned int, len, sizeof(opts));
+		len = min(len, sizeof(opts));
 		if (copy_to_user(optval, (char *)&opts, len))
 			err = -EFAULT;
 
@@ -941,7 +946,7 @@
 		cinfo.hci_handle = sco_pi(sk)->conn->hcon->handle;
 		memcpy(cinfo.dev_class, sco_pi(sk)->conn->hcon->dev_class, 3);
 
-		len = min_t(unsigned int, len, sizeof(cinfo));
+		len = min(len, sizeof(cinfo));
 		if (copy_to_user(optval, (char *)&cinfo, len))
 			err = -EFAULT;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bluetooth/smp.c
+++ linux-xilinx-zynqmp-5.15.0/net/bluetooth/smp.c
@@ -913,7 +913,7 @@
 	 * Confirms and the responder Enters the passkey.
 	 */
 	if (smp->method == OVERLAP) {
-		if (hcon->role == HCI_ROLE_MASTER)
+		if (test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 			smp->method = CFM_PASSKEY;
 		else
 			smp->method = REQ_PASSKEY;
@@ -963,7 +963,7 @@
 
 	smp_send_cmd(smp->conn, SMP_CMD_PAIRING_CONFIRM, sizeof(cp), &cp);
 
-	if (conn->hcon->out)
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_CONFIRM);
 	else
 		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RANDOM);
@@ -979,7 +979,8 @@
 	int ret;
 
 	bt_dev_dbg(conn->hcon->hdev, "conn %p %s", conn,
-		   conn->hcon->out ? "initiator" : "responder");
+		   test_bit(SMP_FLAG_INITIATOR, &smp->flags) ? "initiator" :
+		   "responder");
 
 	ret = smp_c1(smp->tk, smp->rrnd, smp->preq, smp->prsp,
 		     hcon->init_addr_type, &hcon->init_addr,
@@ -993,7 +994,7 @@
 		return SMP_CONFIRM_FAILED;
 	}
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		u8 stk[16];
 		__le64 rand = 0;
 		__le16 ediv = 0;
@@ -1243,14 +1244,15 @@
 	rsp = (void *) &smp->prsp[1];
 
 	/* The responder sends its keys first */
-	if (hcon->out && (smp->remote_key_dist & KEY_DIST_MASK)) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags) &&
+	    (smp->remote_key_dist & KEY_DIST_MASK)) {
 		smp_allow_key_dist(smp);
 		return;
 	}
 
 	req = (void *) &smp->preq[1];
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		keydist = &rsp->init_key_dist;
 		*keydist &= req->init_key_dist;
 	} else {
@@ -1419,7 +1421,7 @@
 	struct hci_conn *hcon = smp->conn->hcon;
 	u8 *na, *nb, a[7], b[7];
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		na   = smp->prnd;
 		nb   = smp->rrnd;
 	} else {
@@ -1447,7 +1449,7 @@
 	a[6] = hcon->init_addr_type;
 	b[6] = hcon->resp_addr_type;
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		local_addr = a;
 		remote_addr = b;
 		memcpy(io_cap, &smp->preq[1], 3);
@@ -1526,7 +1528,7 @@
 		/* The round is only complete when the initiator
 		 * receives pairing random.
 		 */
-		if (!hcon->out) {
+		if (!test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 			smp_send_cmd(conn, SMP_CMD_PAIRING_RANDOM,
 				     sizeof(smp->prnd), smp->prnd);
 			if (smp->passkey_round == 20)
@@ -1554,7 +1556,7 @@
 
 		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RANDOM);
 
-		if (hcon->out) {
+		if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 			smp_send_cmd(conn, SMP_CMD_PAIRING_RANDOM,
 				     sizeof(smp->prnd), smp->prnd);
 			return 0;
@@ -1565,7 +1567,7 @@
 	case SMP_CMD_PUBLIC_KEY:
 	default:
 		/* Initiating device starts the round */
-		if (!hcon->out)
+		if (!test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 			return 0;
 
 		bt_dev_dbg(hdev, "Starting passkey round %u",
@@ -1610,7 +1612,7 @@
 	}
 
 	/* Initiator sends DHKey check first */
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		sc_dhkey_check(smp);
 		SMP_ALLOW_CMD(smp, SMP_CMD_DHKEY_CHECK);
 	} else if (test_and_clear_bit(SMP_FLAG_DHKEY_PENDING, &smp->flags)) {
@@ -1733,7 +1735,7 @@
 	struct smp_cmd_pairing rsp, *req = (void *) skb->data;
 	struct l2cap_chan *chan = conn->smp;
 	struct hci_dev *hdev = conn->hcon->hdev;
-	struct smp_chan *smp;
+	struct smp_chan *smp = chan->data;
 	u8 key_size, auth, sec_level;
 	int ret;
 
@@ -1742,16 +1744,14 @@
 	if (skb->len < sizeof(*req))
 		return SMP_INVALID_PARAMS;
 
-	if (conn->hcon->role != HCI_ROLE_SLAVE)
+	if (smp && test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 		return SMP_CMD_NOTSUPP;
 
-	if (!chan->data)
+	if (!smp) {
 		smp = smp_chan_create(conn);
-	else
-		smp = chan->data;
-
-	if (!smp)
-		return SMP_UNSPECIFIED;
+		if (!smp)
+			return SMP_UNSPECIFIED;
+	}
 
 	/* We didn't start the pairing, so match remote */
 	auth = req->auth_req & AUTH_REQ_MASK(hdev);
@@ -1933,7 +1933,7 @@
 	if (skb->len < sizeof(*rsp))
 		return SMP_INVALID_PARAMS;
 
-	if (conn->hcon->role != HCI_ROLE_MASTER)
+	if (!test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 		return SMP_CMD_NOTSUPP;
 
 	skb_pull(skb, sizeof(*rsp));
@@ -2028,7 +2028,7 @@
 	if (smp->method == REQ_PASSKEY || smp->method == DSP_PASSKEY)
 		return sc_passkey_round(smp, SMP_CMD_PAIRING_CONFIRM);
 
-	if (conn->hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		smp_send_cmd(conn, SMP_CMD_PAIRING_RANDOM, sizeof(smp->prnd),
 			     smp->prnd);
 		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RANDOM);
@@ -2050,7 +2050,7 @@
 	u8 auth;
 
 	/* The issue is only observed when we're in responder role */
-	if (hcon->out)
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 		return SMP_UNSPECIFIED;
 
 	if (hci_dev_test_flag(hdev, HCI_SC_ONLY)) {
@@ -2086,7 +2086,8 @@
 	struct hci_dev *hdev = hcon->hdev;
 
 	bt_dev_dbg(hdev, "conn %p %s", conn,
-		   hcon->out ? "initiator" : "responder");
+		   test_bit(SMP_FLAG_INITIATOR, &smp->flags) ? "initiator" :
+		   "responder");
 
 	if (skb->len < sizeof(smp->pcnf))
 		return SMP_INVALID_PARAMS;
@@ -2108,7 +2109,7 @@
 			return ret;
 	}
 
-	if (conn->hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		smp_send_cmd(conn, SMP_CMD_PAIRING_RANDOM, sizeof(smp->prnd),
 			     smp->prnd);
 		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RANDOM);
@@ -2143,7 +2144,7 @@
 	if (!test_bit(SMP_FLAG_SC, &smp->flags))
 		return smp_random(smp);
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		pkax = smp->local_pk;
 		pkbx = smp->remote_pk;
 		na   = smp->prnd;
@@ -2156,7 +2157,7 @@
 	}
 
 	if (smp->method == REQ_OOB) {
-		if (!hcon->out)
+		if (!test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 			smp_send_cmd(conn, SMP_CMD_PAIRING_RANDOM,
 				     sizeof(smp->prnd), smp->prnd);
 		SMP_ALLOW_CMD(smp, SMP_CMD_DHKEY_CHECK);
@@ -2167,7 +2168,7 @@
 	if (smp->method == REQ_PASSKEY || smp->method == DSP_PASSKEY)
 		return sc_passkey_round(smp, SMP_CMD_PAIRING_RANDOM);
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		u8 cfm[16];
 
 		err = smp_f4(smp->tfm_cmac, smp->remote_pk, smp->local_pk,
@@ -2208,7 +2209,7 @@
 		return SMP_UNSPECIFIED;
 
 	if (smp->method == REQ_OOB) {
-		if (hcon->out) {
+		if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 			sc_dhkey_check(smp);
 			SMP_ALLOW_CMD(smp, SMP_CMD_DHKEY_CHECK);
 		}
@@ -2282,10 +2283,27 @@
 	return false;
 }
 
+static void smp_send_pairing_req(struct smp_chan *smp, __u8 auth)
+{
+	struct smp_cmd_pairing cp;
+
+	if (smp->conn->hcon->type == ACL_LINK)
+		build_bredr_pairing_cmd(smp, &cp, NULL);
+	else
+		build_pairing_cmd(smp->conn, &cp, NULL, auth);
+
+	smp->preq[0] = SMP_CMD_PAIRING_REQ;
+	memcpy(&smp->preq[1], &cp, sizeof(cp));
+
+	smp_send_cmd(smp->conn, SMP_CMD_PAIRING_REQ, sizeof(cp), &cp);
+	SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RSP);
+
+	set_bit(SMP_FLAG_INITIATOR, &smp->flags);
+}
+
 static u8 smp_cmd_security_req(struct l2cap_conn *conn, struct sk_buff *skb)
 {
 	struct smp_cmd_security_req *rp = (void *) skb->data;
-	struct smp_cmd_pairing cp;
 	struct hci_conn *hcon = conn->hcon;
 	struct hci_dev *hdev = hcon->hdev;
 	struct smp_chan *smp;
@@ -2334,16 +2352,20 @@
 
 	skb_pull(skb, sizeof(*rp));
 
-	memset(&cp, 0, sizeof(cp));
-	build_pairing_cmd(conn, &cp, NULL, auth);
+	smp_send_pairing_req(smp, auth);
 
-	smp->preq[0] = SMP_CMD_PAIRING_REQ;
-	memcpy(&smp->preq[1], &cp, sizeof(cp));
+	return 0;
+}
 
-	smp_send_cmd(conn, SMP_CMD_PAIRING_REQ, sizeof(cp), &cp);
-	SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RSP);
+static void smp_send_security_req(struct smp_chan *smp, __u8 auth)
+{
+	struct smp_cmd_security_req cp;
 
-	return 0;
+	cp.auth_req = auth;
+	smp_send_cmd(smp->conn, SMP_CMD_SECURITY_REQ, sizeof(cp), &cp);
+	SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_REQ);
+
+	clear_bit(SMP_FLAG_INITIATOR, &smp->flags);
 }
 
 int smp_conn_security(struct hci_conn *hcon, __u8 sec_level)
@@ -2414,23 +2436,11 @@
 			authreq |= SMP_AUTH_MITM;
 	}
 
-	if (hcon->role == HCI_ROLE_MASTER) {
-		struct smp_cmd_pairing cp;
-
-		build_pairing_cmd(conn, &cp, NULL, authreq);
-		smp->preq[0] = SMP_CMD_PAIRING_REQ;
-		memcpy(&smp->preq[1], &cp, sizeof(cp));
-
-		smp_send_cmd(conn, SMP_CMD_PAIRING_REQ, sizeof(cp), &cp);
-		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RSP);
-	} else {
-		struct smp_cmd_security_req cp;
-		cp.auth_req = authreq;
-		smp_send_cmd(conn, SMP_CMD_SECURITY_REQ, sizeof(cp), &cp);
-		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_REQ);
-	}
+	if (hcon->role == HCI_ROLE_MASTER)
+		smp_send_pairing_req(smp, authreq);
+	else
+		smp_send_security_req(smp, authreq);
 
-	set_bit(SMP_FLAG_INITIATOR, &smp->flags);
 	ret = 0;
 
 unlock:
@@ -2681,8 +2691,6 @@
 
 static u8 sc_select_method(struct smp_chan *smp)
 {
-	struct l2cap_conn *conn = smp->conn;
-	struct hci_conn *hcon = conn->hcon;
 	struct smp_cmd_pairing *local, *remote;
 	u8 local_mitm, remote_mitm, local_io, remote_io, method;
 
@@ -2695,7 +2703,7 @@
 	 * the "struct smp_cmd_pairing" from them we need to skip the
 	 * first byte which contains the opcode.
 	 */
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		local = (void *) &smp->preq[1];
 		remote = (void *) &smp->prsp[1];
 	} else {
@@ -2764,7 +2772,7 @@
 	/* Non-initiating device sends its public key after receiving
 	 * the key from the initiating device.
 	 */
-	if (!hcon->out) {
+	if (!test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		err = sc_send_public_key(smp);
 		if (err)
 			return err;
@@ -2826,7 +2834,7 @@
 	}
 
 	if (smp->method == REQ_OOB) {
-		if (hcon->out)
+		if (test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 			smp_send_cmd(conn, SMP_CMD_PAIRING_RANDOM,
 				     sizeof(smp->prnd), smp->prnd);
 
@@ -2835,7 +2843,7 @@
 		return 0;
 	}
 
-	if (hcon->out)
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 		SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_CONFIRM);
 
 	if (smp->method == REQ_PASSKEY) {
@@ -2850,7 +2858,7 @@
 	/* The Initiating device waits for the non-initiating device to
 	 * send the confirm value.
 	 */
-	if (conn->hcon->out)
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags))
 		return 0;
 
 	err = smp_f4(smp->tfm_cmac, smp->local_pk, smp->remote_pk, smp->prnd,
@@ -2884,7 +2892,7 @@
 	a[6] = hcon->init_addr_type;
 	b[6] = hcon->resp_addr_type;
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		local_addr = a;
 		remote_addr = b;
 		memcpy(io_cap, &smp->prsp[1], 3);
@@ -2909,7 +2917,7 @@
 	if (crypto_memneq(check->e, e, 16))
 		return SMP_DHKEY_CHECK_FAILED;
 
-	if (!hcon->out) {
+	if (!test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		if (test_bit(SMP_FLAG_WAIT_USER, &smp->flags)) {
 			set_bit(SMP_FLAG_DHKEY_PENDING, &smp->flags);
 			return 0;
@@ -2921,7 +2929,7 @@
 
 	sc_add_ltk(smp);
 
-	if (hcon->out) {
+	if (test_bit(SMP_FLAG_INITIATOR, &smp->flags)) {
 		hci_le_start_enc(hcon, 0, 0, smp->tk, smp->enc_key_size);
 		hcon->enc_key_size = smp->enc_key_size;
 	}
@@ -3070,7 +3078,6 @@
 	struct l2cap_conn *conn = chan->conn;
 	struct hci_conn *hcon = conn->hcon;
 	struct hci_dev *hdev = hcon->hdev;
-	struct smp_cmd_pairing req;
 	struct smp_chan *smp;
 
 	bt_dev_dbg(hdev, "chan %p", chan);
@@ -3122,14 +3129,7 @@
 
 	bt_dev_dbg(hdev, "starting SMP over BR/EDR");
 
-	/* Prepare and send the BR/EDR SMP Pairing Request */
-	build_bredr_pairing_cmd(smp, &req, NULL);
-
-	smp->preq[0] = SMP_CMD_PAIRING_REQ;
-	memcpy(&smp->preq[1], &req, sizeof(req));
-
-	smp_send_cmd(conn, SMP_CMD_PAIRING_REQ, sizeof(req), &req);
-	SMP_ALLOW_CMD(smp, SMP_CMD_PAIRING_RSP);
+	smp_send_pairing_req(smp, 0x00);
 }
 
 static void smp_resume_cb(struct l2cap_chan *chan)
--- linux-xilinx-zynqmp-5.15.0.orig/net/bpf/test_run.c
+++ linux-xilinx-zynqmp-5.15.0/net/bpf/test_run.c
@@ -259,6 +259,7 @@
 	if (user_size > size)
 		return ERR_PTR(-EMSGSIZE);
 
+	size = SKB_DATA_ALIGN(size);
 	data = kzalloc(size + headroom + tailroom, GFP_USER);
 	if (!data)
 		return ERR_PTR(-ENOMEM);
@@ -325,10 +326,16 @@
 __bpf_prog_test_run_raw_tp(void *data)
 {
 	struct bpf_raw_tp_test_run_info *info = data;
+	struct bpf_trace_run_ctx run_ctx = {};
+	struct bpf_run_ctx *old_run_ctx;
+
+	old_run_ctx = bpf_set_run_ctx(&run_ctx.run_ctx);
 
 	rcu_read_lock();
 	info->retval = bpf_prog_run(info->prog, info->ctx);
 	rcu_read_unlock();
+
+	bpf_reset_run_ctx(old_run_ctx);
 }
 
 int bpf_prog_test_run_raw_tp(struct bpf_prog *prog,
@@ -954,7 +961,7 @@
 	if (!range_is_zero(user_ctx, offsetofend(typeof(*user_ctx), local_port), sizeof(*user_ctx)))
 		goto out;
 
-	if (user_ctx->local_port > U16_MAX || user_ctx->remote_port > U16_MAX) {
+	if (user_ctx->local_port > U16_MAX) {
 		ret = -ERANGE;
 		goto out;
 	}
@@ -962,7 +969,7 @@
 	ctx.family = (u16)user_ctx->family;
 	ctx.protocol = (u16)user_ctx->protocol;
 	ctx.dport = (u16)user_ctx->local_port;
-	ctx.sport = (__force __be16)user_ctx->remote_port;
+	ctx.sport = user_ctx->remote_port;
 
 	switch (ctx.family) {
 	case AF_INET:
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_cfm_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_cfm_netlink.c
@@ -362,7 +362,7 @@
 
 	memset(&tx_info, 0, sizeof(tx_info));
 
-	instance = nla_get_u32(tb[IFLA_BRIDGE_CFM_CC_RDI_INSTANCE]);
+	instance = nla_get_u32(tb[IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE]);
 	nla_memcpy(&tx_info.dmac.addr,
 		   tb[IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC],
 		   sizeof(tx_info.dmac.addr));
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_device.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_device.c
@@ -38,6 +38,11 @@
 	const unsigned char *dest;
 	u16 vid = 0;
 
+	if (unlikely(!pskb_may_pull(skb, ETH_HLEN))) {
+		kfree_skb(skb);
+		return NETDEV_TX_OK;
+	}
+
 	memset(skb->cb, 0, sizeof(struct br_input_skb_cb));
 
 	rcu_read_lock();
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_fdb.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_fdb.c
@@ -1299,12 +1299,10 @@
 			modified = true;
 		}
 
-		if (test_bit(BR_FDB_ADDED_BY_EXT_LEARN, &fdb->flags)) {
+		if (test_and_set_bit(BR_FDB_ADDED_BY_EXT_LEARN, &fdb->flags)) {
 			/* Refresh entry */
 			fdb->used = jiffies;
-		} else if (!test_bit(BR_FDB_ADDED_BY_USER, &fdb->flags)) {
-			/* Take over SW learned entry */
-			set_bit(BR_FDB_ADDED_BY_EXT_LEARN, &fdb->flags);
+		} else {
 			modified = true;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_forward.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_forward.c
@@ -42,7 +42,7 @@
 	    eth_type_vlan(skb->protocol)) {
 		int depth;
 
-		if (!__vlan_get_protocol(skb, skb->protocol, &depth))
+		if (!vlan_get_protocol_and_depth(skb, skb->protocol, &depth))
 			goto drop;
 
 		skb_set_network_header(skb, depth);
@@ -124,7 +124,7 @@
 
 	skb = skb_clone(skb, GFP_ATOMIC);
 	if (!skb) {
-		dev->stats.tx_dropped++;
+		DEV_STATS_INC(dev, tx_dropped);
 		return -ENOMEM;
 	}
 
@@ -253,6 +253,7 @@
 {
 	struct net_device *dev = BR_INPUT_SKB_CB(skb)->brdev;
 	const unsigned char *src = eth_hdr(skb)->h_source;
+	struct sk_buff *nskb;
 
 	if (!should_deliver(p, skb))
 		return;
@@ -261,12 +262,16 @@
 	if (skb->dev == p->dev && ether_addr_equal(src, addr))
 		return;
 
-	skb = skb_copy(skb, GFP_ATOMIC);
-	if (!skb) {
-		dev->stats.tx_dropped++;
+	__skb_push(skb, ETH_HLEN);
+	nskb = pskb_copy(skb, GFP_ATOMIC);
+	__skb_pull(skb, ETH_HLEN);
+	if (!nskb) {
+		DEV_STATS_INC(dev, tx_dropped);
 		return;
 	}
 
+	skb = nskb;
+	__skb_pull(skb, ETH_HLEN);
 	if (!is_broadcast_ether_addr(addr))
 		memcpy(eth_hdr(skb)->h_dest, addr, ETH_ALEN);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_if.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_if.c
@@ -157,8 +157,9 @@
 			 * This lets us disable promiscuous mode and write
 			 * this config to hw.
 			 */
-			if (br->auto_cnt == 0 ||
-			    (br->auto_cnt == 1 && br_auto_port(p)))
+			if ((p->dev->priv_flags & IFF_UNICAST_FLT) &&
+			    (br->auto_cnt == 0 ||
+			     (br->auto_cnt == 1 && br_auto_port(p))))
 				br_port_clear_promisc(p);
 			else
 				br_port_set_promisc(p);
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_input.c
@@ -30,7 +30,7 @@
 	return netif_receive_skb(skb);
 }
 
-static int br_pass_frame_up(struct sk_buff *skb)
+static int br_pass_frame_up(struct sk_buff *skb, bool promisc)
 {
 	struct net_device *indev, *brdev = BR_INPUT_SKB_CB(skb)->brdev;
 	struct net_bridge *br = netdev_priv(brdev);
@@ -39,6 +39,13 @@
 	dev_sw_netstats_rx_add(brdev, skb->len);
 
 	vg = br_vlan_group_rcu(br);
+
+	/* Reset the offload_fwd_mark because there could be a stacked
+	 * bridge above, and it should not think this bridge it doing
+	 * that bridge's work forwarding out its ports.
+	 */
+	br_switchdev_frame_unmark(skb);
+
 	/* Bridge is just like any other port.  Make sure the
 	 * packet is allowed except in promisc mode when someone
 	 * may be running packet capture.
@@ -58,6 +65,8 @@
 	br_multicast_count(br, NULL, skb, br_multicast_igmp_type(skb),
 			   BR_MCAST_DIR_TX);
 
+	BR_INPUT_SKB_CB(skb)->promisc = promisc;
+
 	return NF_HOOK(NFPROTO_BRIDGE, NF_BR_LOCAL_IN,
 		       dev_net(indev), NULL, skb, indev, NULL,
 		       br_netif_receive_skb);
@@ -75,6 +84,7 @@
 	struct net_bridge_mcast *brmctx;
 	struct net_bridge_vlan *vlan;
 	struct net_bridge *br;
+	bool promisc;
 	u16 vid = 0;
 	u8 state;
 
@@ -95,7 +105,9 @@
 	if (p->flags & BR_LEARNING)
 		br_fdb_update(br, p, eth_hdr(skb)->h_source, vid, 0);
 
-	local_rcv = !!(br->dev->flags & IFF_PROMISC);
+	promisc = !!(br->dev->flags & IFF_PROMISC);
+	local_rcv = promisc;
+
 	if (is_multicast_ether_addr(eth_hdr(skb)->h_dest)) {
 		/* by definition the broadcast is also a multicast address */
 		if (is_broadcast_ether_addr(eth_hdr(skb)->h_dest)) {
@@ -139,12 +151,12 @@
 			if ((mdst && mdst->host_joined) ||
 			    br_multicast_is_router(brmctx, skb)) {
 				local_rcv = true;
-				br->dev->stats.multicast++;
+				DEV_STATS_INC(br->dev, multicast);
 			}
 			mcast_hit = true;
 		} else {
 			local_rcv = true;
-			br->dev->stats.multicast++;
+			DEV_STATS_INC(br->dev, multicast);
 		}
 		break;
 	case BR_PKT_UNICAST:
@@ -158,7 +170,7 @@
 		unsigned long now = jiffies;
 
 		if (test_bit(BR_FDB_LOCAL, &dst->flags))
-			return br_pass_frame_up(skb);
+			return br_pass_frame_up(skb, false);
 
 		if (now != dst->used)
 			dst->used = now;
@@ -171,7 +183,7 @@
 	}
 
 	if (local_rcv)
-		return br_pass_frame_up(skb);
+		return br_pass_frame_up(skb, promisc);
 
 out:
 	return 0;
@@ -343,6 +355,8 @@
 				goto forward;
 		}
 
+		BR_INPUT_SKB_CB(skb)->promisc = false;
+
 		/* The else clause should be hit when nf_hook():
 		 *   - returns < 0 (drop/error)
 		 *   - returns = 0 (stolen/nf_queue)
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_ioctl.c
@@ -71,7 +71,8 @@
 
 	num = br_fdb_fillbuf(br, buf, maxnum, offset);
 	if (num > 0) {
-		if (copy_to_user(userbuf, buf, num*sizeof(struct __fdb_entry)))
+		if (copy_to_user(userbuf, buf,
+				 array_size(num, sizeof(struct __fdb_entry))))
 			num = -EFAULT;
 	}
 	kfree(buf);
@@ -188,7 +189,7 @@
 			return -ENOMEM;
 
 		get_port_ifindices(br, indices, num);
-		if (copy_to_user(argp, indices, num * sizeof(int)))
+		if (copy_to_user(argp, indices, array_size(num, sizeof(int))))
 			num =  -EFAULT;
 		kfree(indices);
 		return num;
@@ -336,7 +337,8 @@
 
 		args[2] = get_bridge_ifindices(net, indices, args[2]);
 
-		ret = copy_to_user(uarg, indices, args[2]*sizeof(int))
+		ret = copy_to_user((void __user *)args[1], indices,
+				   array_size(args[2], sizeof(int)))
 			? -EFAULT : args[2];
 
 		kfree(indices);
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_mdb.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_mdb.c
@@ -620,21 +620,40 @@
 }
 
 static int br_mdb_queue_one(struct list_head *mdb_list,
+			    struct net_device *dev,
+			    unsigned long action,
 			    enum switchdev_obj_id id,
 			    const struct net_bridge_mdb_entry *mp,
 			    struct net_device *orig_dev)
 {
-	struct switchdev_obj_port_mdb *mdb;
+	struct switchdev_obj_port_mdb mdb = {
+		.obj = {
+			.id = id,
+			.orig_dev = orig_dev,
+		},
+	};
+	struct switchdev_obj_port_mdb *pmdb;
+
+	br_switchdev_mdb_populate(&mdb, mp);
+
+	if (action == SWITCHDEV_PORT_OBJ_ADD &&
+	    switchdev_port_obj_act_is_deferred(dev, action, &mdb.obj)) {
+		/* This event is already in the deferred queue of
+		 * events, so this replay must be elided, lest the
+		 * driver receives duplicate events for it. This can
+		 * only happen when replaying additions, since
+		 * modifications are always immediately visible in
+		 * br->mdb_list, whereas actual event delivery may be
+		 * delayed.
+		 */
+		return 0;
+	}
 
-	mdb = kzalloc(sizeof(*mdb), GFP_ATOMIC);
-	if (!mdb)
+	pmdb = kmemdup(&mdb, sizeof(mdb), GFP_ATOMIC);
+	if (!pmdb)
 		return -ENOMEM;
 
-	mdb->obj.id = id;
-	mdb->obj.orig_dev = orig_dev;
-	br_switchdev_mdb_populate(mdb, mp);
-	list_add_tail(&mdb->obj.list, mdb_list);
-
+	list_add_tail(&pmdb->obj.list, mdb_list);
 	return 0;
 }
 
@@ -662,51 +681,50 @@
 	if (!br_opt_get(br, BROPT_MULTICAST_ENABLED))
 		return 0;
 
-	/* We cannot walk over br->mdb_list protected just by the rtnl_mutex,
-	 * because the write-side protection is br->multicast_lock. But we
-	 * need to emulate the [ blocking ] calling context of a regular
-	 * switchdev event, so since both br->multicast_lock and RCU read side
-	 * critical sections are atomic, we have no choice but to pick the RCU
-	 * read side lock, queue up all our events, leave the critical section
-	 * and notify switchdev from blocking context.
+	if (adding)
+		action = SWITCHDEV_PORT_OBJ_ADD;
+	else
+		action = SWITCHDEV_PORT_OBJ_DEL;
+
+	/* br_switchdev_mdb_queue_one() will take care to not queue a
+	 * replay of an event that is already pending in the switchdev
+	 * deferred queue. In order to safely determine that, there
+	 * must be no new deferred MDB notifications enqueued for the
+	 * duration of the MDB scan. Therefore, grab the write-side
+	 * lock to avoid racing with any concurrent IGMP/MLD snooping.
 	 */
-	rcu_read_lock();
+	spin_lock_bh(&br->multicast_lock);
 
-	hlist_for_each_entry_rcu(mp, &br->mdb_list, mdb_node) {
+	hlist_for_each_entry(mp, &br->mdb_list, mdb_node) {
 		struct net_bridge_port_group __rcu * const *pp;
 		const struct net_bridge_port_group *p;
 
 		if (mp->host_joined) {
-			err = br_mdb_queue_one(&mdb_list,
+			err = br_mdb_queue_one(&mdb_list, dev, action,
 					       SWITCHDEV_OBJ_ID_HOST_MDB,
 					       mp, br_dev);
 			if (err) {
-				rcu_read_unlock();
+				spin_unlock_bh(&br->multicast_lock);
 				goto out_free_mdb;
 			}
 		}
 
-		for (pp = &mp->ports; (p = rcu_dereference(*pp)) != NULL;
+		for (pp = &mp->ports; (p = mlock_dereference(*pp, br)) != NULL;
 		     pp = &p->next) {
 			if (p->key.port->dev != dev)
 				continue;
 
-			err = br_mdb_queue_one(&mdb_list,
-					       SWITCHDEV_OBJ_ID_PORT_MDB,
-					       mp, dev);
+			err = br_mdb_queue_one(&mdb_list, dev, action,
+							 SWITCHDEV_OBJ_ID_PORT_MDB,
+							 mp, dev);
 			if (err) {
-				rcu_read_unlock();
+				spin_unlock_bh(&br->multicast_lock);
 				goto out_free_mdb;
 			}
 		}
 	}
 
-	rcu_read_unlock();
-
-	if (adding)
-		action = SWITCHDEV_PORT_OBJ_ADD;
-	else
-		action = SWITCHDEV_PORT_OBJ_DEL;
+	spin_unlock_bh(&br->multicast_lock);
 
 	list_for_each_entry(obj, &mdb_list, list) {
 		err = br_mdb_replay_one(nb, dev, SWITCHDEV_OBJ_PORT_MDB(obj),
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_multicast.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_multicast.c
@@ -82,6 +82,9 @@
 				     struct net_bridge_port_group *pg);
 static void __br_multicast_stop(struct net_bridge_mcast *brmctx);
 
+static int br_mc_disabled_update(struct net_device *dev, bool value,
+				 struct netlink_ext_ack *extack);
+
 static struct net_bridge_port_group *
 br_sg_port_find(struct net_bridge *br,
 		struct net_bridge_port_group_sg_key *sg_p)
@@ -1156,6 +1159,7 @@
 		return mp;
 
 	if (atomic_read(&br->mdb_hash_tbl.nelems) >= br->hash_max) {
+		br_mc_disabled_update(br->dev, false, NULL);
 		br_opt_toggle(br, BROPT_MULTICAST_ENABLED, false);
 		return ERR_PTR(-E2BIG);
 	}
@@ -1603,6 +1607,10 @@
 }
 #endif
 
+static void br_multicast_query_delay_expired(struct timer_list *t)
+{
+}
+
 static void br_multicast_select_own_querier(struct net_bridge_mcast *brmctx,
 					    struct br_ip *ip,
 					    struct sk_buff *skb)
@@ -1882,16 +1890,14 @@
 {
 	struct net_bridge *br = port->br;
 	struct net_bridge_port_group *pg;
-	HLIST_HEAD(deleted_head);
 	struct hlist_node *n;
 
 	/* Take care of the remaining groups, only perm ones should be left */
 	spin_lock_bh(&br->multicast_lock);
 	hlist_for_each_entry_safe(pg, n, &port->mglist, mglist)
 		br_multicast_find_del_pg(br, pg);
-	hlist_move_list(&br->mcast_gc_list, &deleted_head);
 	spin_unlock_bh(&br->multicast_lock);
-	br_multicast_gc(&deleted_head);
+	flush_work(&br->mcast_gc_work);
 	br_multicast_port_ctx_deinit(&port->multicast_ctx);
 	free_percpu(port->mcast_stats);
 }
@@ -3020,7 +3026,7 @@
 				unsigned long max_delay)
 {
 	if (!timer_pending(&query->timer))
-		query->delay_time = jiffies + max_delay;
+		mod_timer(&query->delay_timer, jiffies + max_delay);
 
 	mod_timer(&query->timer, jiffies + brmctx->multicast_querier_interval);
 }
@@ -3863,13 +3869,11 @@
 	brmctx->multicast_querier_interval = 255 * HZ;
 	brmctx->multicast_membership_interval = 260 * HZ;
 
-	brmctx->ip4_other_query.delay_time = 0;
 	brmctx->ip4_querier.port_ifidx = 0;
 	seqcount_spinlock_init(&brmctx->ip4_querier.seq, &br->multicast_lock);
 	brmctx->multicast_igmp_version = 2;
 #if IS_ENABLED(CONFIG_IPV6)
 	brmctx->multicast_mld_version = 1;
-	brmctx->ip6_other_query.delay_time = 0;
 	brmctx->ip6_querier.port_ifidx = 0;
 	seqcount_spinlock_init(&brmctx->ip6_querier.seq, &br->multicast_lock);
 #endif
@@ -3878,6 +3882,8 @@
 		    br_ip4_multicast_local_router_expired, 0);
 	timer_setup(&brmctx->ip4_other_query.timer,
 		    br_ip4_multicast_querier_expired, 0);
+	timer_setup(&brmctx->ip4_other_query.delay_timer,
+		    br_multicast_query_delay_expired, 0);
 	timer_setup(&brmctx->ip4_own_query.timer,
 		    br_ip4_multicast_query_expired, 0);
 #if IS_ENABLED(CONFIG_IPV6)
@@ -3885,6 +3891,8 @@
 		    br_ip6_multicast_local_router_expired, 0);
 	timer_setup(&brmctx->ip6_other_query.timer,
 		    br_ip6_multicast_querier_expired, 0);
+	timer_setup(&brmctx->ip6_other_query.delay_timer,
+		    br_multicast_query_delay_expired, 0);
 	timer_setup(&brmctx->ip6_own_query.timer,
 		    br_ip6_multicast_query_expired, 0);
 #endif
@@ -4019,10 +4027,12 @@
 {
 	del_timer_sync(&brmctx->ip4_mc_router_timer);
 	del_timer_sync(&brmctx->ip4_other_query.timer);
+	del_timer_sync(&brmctx->ip4_other_query.delay_timer);
 	del_timer_sync(&brmctx->ip4_own_query.timer);
 #if IS_ENABLED(CONFIG_IPV6)
 	del_timer_sync(&brmctx->ip6_mc_router_timer);
 	del_timer_sync(&brmctx->ip6_other_query.timer);
+	del_timer_sync(&brmctx->ip6_other_query.delay_timer);
 	del_timer_sync(&brmctx->ip6_own_query.timer);
 #endif
 }
@@ -4465,13 +4475,15 @@
 	max_delay = brmctx->multicast_query_response_interval;
 
 	if (!timer_pending(&brmctx->ip4_other_query.timer))
-		brmctx->ip4_other_query.delay_time = jiffies + max_delay;
+		mod_timer(&brmctx->ip4_other_query.delay_timer,
+			  jiffies + max_delay);
 
 	br_multicast_start_querier(brmctx, &brmctx->ip4_own_query);
 
 #if IS_ENABLED(CONFIG_IPV6)
 	if (!timer_pending(&brmctx->ip6_other_query.timer))
-		brmctx->ip6_other_query.delay_time = jiffies + max_delay;
+		mod_timer(&brmctx->ip6_other_query.delay_timer,
+			  jiffies + max_delay);
 
 	br_multicast_start_querier(brmctx, &brmctx->ip6_own_query);
 #endif
@@ -4522,6 +4534,38 @@
 }
 #endif
 
+void br_multicast_set_query_intvl(struct net_bridge_mcast *brmctx,
+				  unsigned long val)
+{
+	unsigned long intvl_jiffies = clock_t_to_jiffies(val);
+
+	if (intvl_jiffies < BR_MULTICAST_QUERY_INTVL_MIN) {
+		br_info(brmctx->br,
+			"trying to set multicast query interval below minimum, setting to %lu (%ums)\n",
+			jiffies_to_clock_t(BR_MULTICAST_QUERY_INTVL_MIN),
+			jiffies_to_msecs(BR_MULTICAST_QUERY_INTVL_MIN));
+		intvl_jiffies = BR_MULTICAST_QUERY_INTVL_MIN;
+	}
+
+	brmctx->multicast_query_interval = intvl_jiffies;
+}
+
+void br_multicast_set_startup_query_intvl(struct net_bridge_mcast *brmctx,
+					  unsigned long val)
+{
+	unsigned long intvl_jiffies = clock_t_to_jiffies(val);
+
+	if (intvl_jiffies < BR_MULTICAST_STARTUP_QUERY_INTVL_MIN) {
+		br_info(brmctx->br,
+			"trying to set multicast startup query interval below minimum, setting to %lu (%ums)\n",
+			jiffies_to_clock_t(BR_MULTICAST_STARTUP_QUERY_INTVL_MIN),
+			jiffies_to_msecs(BR_MULTICAST_STARTUP_QUERY_INTVL_MIN));
+		intvl_jiffies = BR_MULTICAST_STARTUP_QUERY_INTVL_MIN;
+	}
+
+	brmctx->multicast_startup_query_interval = intvl_jiffies;
+}
+
 /**
  * br_multicast_list_adjacent - Returns snooped multicast addresses
  * @dev:	The bridge port adjacent to which to retrieve addresses
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_netfilter_hooks.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_netfilter_hooks.c
@@ -33,6 +33,7 @@
 #include <net/ip.h>
 #include <net/ipv6.h>
 #include <net/addrconf.h>
+#include <net/dst_metadata.h>
 #include <net/route.h>
 #include <net/netfilter/br_netfilter.h>
 #include <net/netns/generic.h>
@@ -43,6 +44,10 @@
 #include <linux/sysctl.h>
 #endif
 
+#if IS_ENABLED(CONFIG_NF_CONNTRACK)
+#include <net/netfilter/nf_conntrack_core.h>
+#endif
+
 static unsigned int brnf_net_id __read_mostly;
 
 struct brnf_net {
@@ -384,6 +389,7 @@
 				/* - Bridged-and-DNAT'ed traffic doesn't
 				 *   require ip_forwarding. */
 				if (rt->dst.dev == dev) {
+					skb_dst_drop(skb);
 					skb_dst_set(skb, &rt->dst);
 					goto bridged_dnat;
 				}
@@ -413,6 +419,7 @@
 			kfree_skb(skb);
 			return 0;
 		}
+		skb_dst_drop(skb);
 		skb_dst_set_noref(skb, &rt->dst);
 	}
 
@@ -535,6 +542,100 @@
 	return NF_STOLEN;
 }
 
+#if IS_ENABLED(CONFIG_NF_CONNTRACK)
+/* conntracks' nf_confirm logic cannot handle cloned skbs referencing
+ * the same nf_conn entry, which will happen for multicast (broadcast)
+ * Frames on bridges.
+ *
+ * Example:
+ *      macvlan0
+ *      br0
+ *  ethX  ethY
+ *
+ * ethX (or Y) receives multicast or broadcast packet containing
+ * an IP packet, not yet in conntrack table.
+ *
+ * 1. skb passes through bridge and fake-ip (br_netfilter)Prerouting.
+ *    -> skb->_nfct now references a unconfirmed entry
+ * 2. skb is broad/mcast packet. bridge now passes clones out on each bridge
+ *    interface.
+ * 3. skb gets passed up the stack.
+ * 4. In macvlan case, macvlan driver retains clone(s) of the mcast skb
+ *    and schedules a work queue to send them out on the lower devices.
+ *
+ *    The clone skb->_nfct is not a copy, it is the same entry as the
+ *    original skb.  The macvlan rx handler then returns RX_HANDLER_PASS.
+ * 5. Normal conntrack hooks (in NF_INET_LOCAL_IN) confirm the orig skb.
+ *
+ * The Macvlan broadcast worker and normal confirm path will race.
+ *
+ * This race will not happen if step 2 already confirmed a clone. In that
+ * case later steps perform skb_clone() with skb->_nfct already confirmed (in
+ * hash table).  This works fine.
+ *
+ * But such confirmation won't happen when eb/ip/nftables rules dropped the
+ * packets before they reached the nf_confirm step in postrouting.
+ *
+ * Work around this problem by explicit confirmation of the entry at
+ * LOCAL_IN time, before upper layer has a chance to clone the unconfirmed
+ * entry.
+ *
+ */
+static unsigned int br_nf_local_in(void *priv,
+				   struct sk_buff *skb,
+				   const struct nf_hook_state *state)
+{
+	bool promisc = BR_INPUT_SKB_CB(skb)->promisc;
+	struct nf_conntrack *nfct = skb_nfct(skb);
+	const struct nf_ct_hook *ct_hook;
+	struct nf_conn *ct;
+	int ret;
+
+	if (promisc) {
+		nf_reset_ct(skb);
+		return NF_ACCEPT;
+	}
+
+	if (!nfct || skb->pkt_type == PACKET_HOST)
+		return NF_ACCEPT;
+
+	ct = container_of(nfct, struct nf_conn, ct_general);
+	if (likely(nf_ct_is_confirmed(ct)))
+		return NF_ACCEPT;
+
+	if (WARN_ON_ONCE(refcount_read(&nfct->use) != 1)) {
+		nf_reset_ct(skb);
+		return NF_ACCEPT;
+	}
+
+	WARN_ON_ONCE(skb_shared(skb));
+
+	/* We can't call nf_confirm here, it would create a dependency
+	 * on nf_conntrack module.
+	 */
+	ct_hook = rcu_dereference(nf_ct_hook);
+	if (!ct_hook) {
+		skb->_nfct = 0ul;
+		nf_conntrack_put(nfct);
+		return NF_ACCEPT;
+	}
+
+	nf_bridge_pull_encap_header(skb);
+	ret = ct_hook->confirm(skb);
+	switch (ret & NF_VERDICT_MASK) {
+	case NF_STOLEN:
+		return NF_STOLEN;
+	default:
+		nf_bridge_push_encap_header(skb);
+		break;
+	}
+
+	ct = container_of(nfct, struct nf_conn, ct_general);
+	WARN_ON_ONCE(!nf_ct_is_confirmed(ct));
+
+	return ret;
+}
+#endif
 
 /* PF_BRIDGE/FORWARD *************************************************/
 static int br_nf_forward_finish(struct net *net, struct sock *sk, struct sk_buff *skb)
@@ -743,11 +844,18 @@
 	if (nf_bridge->frag_max_size && nf_bridge->frag_max_size < mtu)
 		mtu = nf_bridge->frag_max_size;
 
+	nf_bridge_update_protocol(skb);
+	nf_bridge_push_encap_header(skb);
+
 	if (skb_is_gso(skb) || skb->len + mtu_reserved <= mtu) {
 		nf_bridge_info_free(skb);
 		return br_dev_queue_push_xmit(net, sk, skb);
 	}
 
+	/* Fragmentation on metadata/template dst is not supported */
+	if (unlikely(!skb_valid_dst(skb)))
+		goto drop;
+
 	/* This is wrong! We should preserve the original fragment
 	 * boundaries by preserving frag_list rather than refragmenting.
 	 */
@@ -760,8 +868,6 @@
 
 		IPCB(skb)->frag_max_size = nf_bridge->frag_max_size;
 
-		nf_bridge_update_protocol(skb);
-
 		data = this_cpu_ptr(&brnf_frag_data_storage);
 
 		if (skb_vlan_tag_present(skb)) {
@@ -789,8 +895,6 @@
 
 		IP6CB(skb)->frag_max_size = nf_bridge->frag_max_size;
 
-		nf_bridge_update_protocol(skb);
-
 		data = this_cpu_ptr(&brnf_frag_data_storage);
 		data->encap_size = nf_bridge_encap_header_len(skb);
 		data->size = ETH_HLEN + data->encap_size;
@@ -867,11 +971,17 @@
 {
 	struct nf_bridge_info *nf_bridge = nf_bridge_info_get(skb);
 
-	if (nf_bridge && !nf_bridge->in_prerouting &&
-	    !netif_is_l3_master(skb->dev) &&
-	    !netif_is_l3_slave(skb->dev)) {
-		state->okfn(state->net, state->sk, skb);
-		return NF_STOLEN;
+	if (nf_bridge) {
+		if (nf_bridge->sabotage_in_done)
+			return NF_ACCEPT;
+
+		if (!nf_bridge->in_prerouting &&
+		    !netif_is_l3_master(skb->dev) &&
+		    !netif_is_l3_slave(skb->dev)) {
+			nf_bridge->sabotage_in_done = 1;
+			state->okfn(state->net, state->sk, skb);
+			return NF_STOLEN;
+		}
 	}
 
 	return NF_ACCEPT;
@@ -928,6 +1038,14 @@
 		.hooknum = NF_BR_PRE_ROUTING,
 		.priority = NF_BR_PRI_BRNF,
 	},
+#if IS_ENABLED(CONFIG_NF_CONNTRACK)
+	{
+		.hook = br_nf_local_in,
+		.pf = NFPROTO_BRIDGE,
+		.hooknum = NF_BR_LOCAL_IN,
+		.priority = NF_BR_PRI_LAST,
+	},
+#endif
 	{
 		.hook = br_nf_forward_ip,
 		.pf = NFPROTO_BRIDGE,
@@ -1013,9 +1131,24 @@
 		return okfn(net, sk, skb);
 
 	ops = nf_hook_entries_get_hook_ops(e);
-	for (i = 0; i < e->num_hook_entries &&
-	      ops[i]->priority <= NF_BR_PRI_BRNF; i++)
-		;
+	for (i = 0; i < e->num_hook_entries; i++) {
+		/* These hooks have already been called */
+		if (ops[i]->priority < NF_BR_PRI_BRNF)
+			continue;
+
+		/* These hooks have not been called yet, run them. */
+		if (ops[i]->priority > NF_BR_PRI_BRNF)
+			break;
+
+		/* take a closer look at NF_BR_PRI_BRNF. */
+		if (ops[i]->hook == br_nf_pre_routing) {
+			/* This hook diverted the skb to this function,
+			 * hooks after this have not been run yet.
+			 */
+			i++;
+			break;
+		}
+	}
 
 	nf_hook_state_init(&state, hook, NFPROTO_BRIDGE, indev, outdev,
 			   sk, net, okfn);
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_netfilter_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_netfilter_ipv6.c
@@ -197,6 +197,7 @@
 			kfree_skb(skb);
 			return 0;
 		}
+		skb_dst_drop(skb);
 		skb_dst_set_noref(skb, &rt->dst);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_netlink.c
@@ -619,7 +619,7 @@
 {
 	u32 filter = RTEXT_FILTER_BRVLAN_COMPRESSED;
 
-	return br_info_notify(event, br, port, filter);
+	br_info_notify(event, br, port, filter);
 }
 
 /*
@@ -1357,7 +1357,7 @@
 	if (data[IFLA_BR_MCAST_QUERY_INTVL]) {
 		u64 val = nla_get_u64(data[IFLA_BR_MCAST_QUERY_INTVL]);
 
-		br->multicast_ctx.multicast_query_interval = clock_t_to_jiffies(val);
+		br_multicast_set_query_intvl(&br->multicast_ctx, val);
 	}
 
 	if (data[IFLA_BR_MCAST_QUERY_RESPONSE_INTVL]) {
@@ -1369,7 +1369,7 @@
 	if (data[IFLA_BR_MCAST_STARTUP_QUERY_INTVL]) {
 		u64 val = nla_get_u64(data[IFLA_BR_MCAST_STARTUP_QUERY_INTVL]);
 
-		br->multicast_ctx.multicast_startup_query_interval = clock_t_to_jiffies(val);
+		br_multicast_set_startup_query_intvl(&br->multicast_ctx, val);
 	}
 
 	if (data[IFLA_BR_MCAST_STATS_ENABLED]) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_private.h
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_private.h
@@ -28,6 +28,8 @@
 #define BR_MAX_PORTS	(1<<BR_PORT_BITS)
 
 #define BR_MULTICAST_DEFAULT_HASH_MAX 4096
+#define BR_MULTICAST_QUERY_INTVL_MIN msecs_to_jiffies(1000)
+#define BR_MULTICAST_STARTUP_QUERY_INTVL_MIN BR_MULTICAST_QUERY_INTVL_MIN
 
 #define BR_HWDOM_MAX BITS_PER_LONG
 
@@ -75,7 +77,7 @@
 /* other querier */
 struct bridge_mcast_other_query {
 	struct timer_list		timer;
-	unsigned long			delay_time;
+	struct timer_list		delay_timer;
 };
 
 /* selected querier */
@@ -545,6 +547,7 @@
 #endif
 	u8 proxyarp_replied:1;
 	u8 src_port_isolated:1;
+	u8 promisc:1;
 #ifdef CONFIG_BRIDGE_VLAN_FILTERING
 	u8 vlan_filtered:1;
 #endif
@@ -968,6 +971,10 @@
 				    int nest_attr);
 size_t br_multicast_querier_state_size(void);
 size_t br_rports_size(const struct net_bridge_mcast *brmctx);
+void br_multicast_set_query_intvl(struct net_bridge_mcast *brmctx,
+				  unsigned long val);
+void br_multicast_set_startup_query_intvl(struct net_bridge_mcast *brmctx,
+					  unsigned long val);
 
 static inline bool br_group_is_l2(const struct br_ip *group)
 {
@@ -1060,7 +1067,7 @@
 		own_querier_enabled = false;
 	}
 
-	return time_is_before_jiffies(querier->delay_time) &&
+	return !timer_pending(&querier->delay_timer) &&
 	       (own_querier_enabled || timer_pending(&querier->timer));
 }
 
@@ -1152,9 +1159,9 @@
 static inline bool
 br_multicast_ctx_vlan_global_disabled(const struct net_bridge_mcast *brmctx)
 {
-	return br_opt_get(brmctx->br, BROPT_MCAST_VLAN_SNOOPING_ENABLED) &&
-	       br_multicast_ctx_is_vlan(brmctx) &&
-	       !(brmctx->vlan->priv_flags & BR_VLFLAG_GLOBAL_MCAST_ENABLED);
+	return br_multicast_ctx_is_vlan(brmctx) &&
+	       (!br_opt_get(brmctx->br, BROPT_MCAST_VLAN_SNOOPING_ENABLED) ||
+		!(brmctx->vlan->priv_flags & BR_VLFLAG_GLOBAL_MCAST_ENABLED));
 }
 
 static inline bool
@@ -1911,11 +1918,13 @@
 
 static inline int br_cfm_mep_count(struct net_bridge *br, u32 *count)
 {
+	*count = 0;
 	return -EOPNOTSUPP;
 }
 
 static inline int br_cfm_peer_mep_count(struct net_bridge *br, u32 *count)
 {
+	*count = 0;
 	return -EOPNOTSUPP;
 }
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_private_tunnel.h
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_private_tunnel.h
@@ -27,6 +27,10 @@
 int br_get_vlan_tunnel_info_size(struct net_bridge_vlan_group *vg);
 int br_fill_vlan_tunnel_info(struct sk_buff *skb,
 			     struct net_bridge_vlan_group *vg);
+bool vlan_tunid_inrange(const struct net_bridge_vlan *v_curr,
+			const struct net_bridge_vlan *v_last);
+int br_vlan_tunnel_info(const struct net_bridge_port *p, int cmd,
+			u16 vid, u32 tun_id, bool *changed);
 
 #ifdef CONFIG_BRIDGE_VLAN_FILTERING
 /* br_vlan_tunnel.c */
@@ -43,10 +47,6 @@
 				   struct net_bridge_vlan_group *vg);
 int br_handle_egress_vlan_tunnel(struct sk_buff *skb,
 				 struct net_bridge_vlan *vlan);
-bool vlan_tunid_inrange(const struct net_bridge_vlan *v_curr,
-			const struct net_bridge_vlan *v_last);
-int br_vlan_tunnel_info(const struct net_bridge_port *p, int cmd,
-			u16 vid, u32 tun_id, bool *changed);
 #else
 static inline int vlan_tunnel_init(struct net_bridge_vlan_group *vg)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_stp_if.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_stp_if.c
@@ -201,6 +201,9 @@
 {
 	ASSERT_RTNL();
 
+	if (!net_eq(dev_net(br->dev), &init_net))
+		NL_SET_ERR_MSG_MOD(extack, "STP does not work in non-root netns");
+
 	if (br_mrp_enabled(br)) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "STP can't be enabled if MRP is already enabled");
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_sysfs_br.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_sysfs_br.c
@@ -658,7 +658,7 @@
 static int set_query_interval(struct net_bridge *br, unsigned long val,
 			      struct netlink_ext_ack *extack)
 {
-	br->multicast_ctx.multicast_query_interval = clock_t_to_jiffies(val);
+	br_multicast_set_query_intvl(&br->multicast_ctx, val);
 	return 0;
 }
 
@@ -706,7 +706,7 @@
 static int set_startup_query_interval(struct net_bridge *br, unsigned long val,
 				      struct netlink_ext_ack *extack)
 {
-	br->multicast_ctx.multicast_startup_query_interval = clock_t_to_jiffies(val);
+	br_multicast_set_startup_query_intvl(&br->multicast_ctx, val);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_vlan.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_vlan.c
@@ -560,10 +560,10 @@
 		    !br_opt_get(br, BROPT_VLAN_STATS_ENABLED)) {
 			if (*state == BR_STATE_FORWARDING) {
 				*state = br_vlan_get_pvid_state(vg);
-				return br_vlan_state_allowed(*state, true);
-			} else {
-				return true;
+				if (!br_vlan_state_allowed(*state, true))
+					goto drop;
 			}
+			return true;
 		}
 	}
 	v = br_vlan_find(vg, *vid);
@@ -904,6 +904,8 @@
 	list_for_each_entry(p, &br->port_list, list) {
 		vg = nbp_vlan_group(p);
 		list_for_each_entry(vlan, &vg->vlan_list, vlist) {
+			if (vlan->priv_flags & BR_VLFLAG_ADDED_BY_SWITCHDEV)
+				continue;
 			err = vlan_vid_add(p->dev, proto, vlan->vid);
 			if (err)
 				goto err_filt;
@@ -918,8 +920,11 @@
 	/* Delete VLANs for the old proto from the device filter. */
 	list_for_each_entry(p, &br->port_list, list) {
 		vg = nbp_vlan_group(p);
-		list_for_each_entry(vlan, &vg->vlan_list, vlist)
+		list_for_each_entry(vlan, &vg->vlan_list, vlist) {
+			if (vlan->priv_flags & BR_VLFLAG_ADDED_BY_SWITCHDEV)
+				continue;
 			vlan_vid_del(p->dev, oldproto, vlan->vid);
+		}
 	}
 
 	return 0;
@@ -928,13 +933,19 @@
 	attr.u.vlan_protocol = ntohs(oldproto);
 	switchdev_port_attr_set(br->dev, &attr, NULL);
 
-	list_for_each_entry_continue_reverse(vlan, &vg->vlan_list, vlist)
+	list_for_each_entry_continue_reverse(vlan, &vg->vlan_list, vlist) {
+		if (vlan->priv_flags & BR_VLFLAG_ADDED_BY_SWITCHDEV)
+			continue;
 		vlan_vid_del(p->dev, proto, vlan->vid);
+	}
 
 	list_for_each_entry_continue_reverse(p, &br->port_list, list) {
 		vg = nbp_vlan_group(p);
-		list_for_each_entry(vlan, &vg->vlan_list, vlist)
+		list_for_each_entry(vlan, &vg->vlan_list, vlist) {
+			if (vlan->priv_flags & BR_VLFLAG_ADDED_BY_SWITCHDEV)
+				continue;
 			vlan_vid_del(p->dev, proto, vlan->vid);
+		}
 	}
 
 	return err;
@@ -2105,7 +2116,8 @@
 			goto out_err;
 		}
 		err = br_vlan_dump_dev(dev, skb, cb, dump_flags);
-		if (err && err != -EMSGSIZE)
+		/* if the dump completed without an error we return 0 here */
+		if (err != -EMSGSIZE)
 			goto out_err;
 	} else {
 		for_each_netdev_rcu(net, dev) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/br_vlan_options.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/br_vlan_options.c
@@ -521,7 +521,7 @@
 		u64 val;
 
 		val = nla_get_u64(tb[BRIDGE_VLANDB_GOPTS_MCAST_QUERY_INTVL]);
-		v->br_mcast_ctx.multicast_query_interval = clock_t_to_jiffies(val);
+		br_multicast_set_query_intvl(&v->br_mcast_ctx, val);
 		*changed = true;
 	}
 	if (tb[BRIDGE_VLANDB_GOPTS_MCAST_QUERY_RESPONSE_INTVL]) {
@@ -535,7 +535,7 @@
 		u64 val;
 
 		val = nla_get_u64(tb[BRIDGE_VLANDB_GOPTS_MCAST_STARTUP_QUERY_INTVL]);
-		v->br_mcast_ctx.multicast_startup_query_interval = clock_t_to_jiffies(val);
+		br_multicast_set_startup_query_intvl(&v->br_mcast_ctx, val);
 		*changed = true;
 	}
 	if (tb[BRIDGE_VLANDB_GOPTS_MCAST_QUERIER]) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/ebtable_broute.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/ebtable_broute.c
@@ -36,18 +36,10 @@
 	.entries	= (char *)&initial_chain,
 };
 
-static int check(const struct ebt_table_info *info, unsigned int valid_hooks)
-{
-	if (valid_hooks & ~(1 << NF_BR_BROUTING))
-		return -EINVAL;
-	return 0;
-}
-
 static const struct ebt_table broute_table = {
 	.name		= "broute",
 	.table		= &initial_table,
 	.valid_hooks	= 1 << NF_BR_BROUTING,
-	.check		= check,
 	.me		= THIS_MODULE,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/ebtable_filter.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/ebtable_filter.c
@@ -43,18 +43,10 @@
 	.entries	= (char *)initial_chains,
 };
 
-static int check(const struct ebt_table_info *info, unsigned int valid_hooks)
-{
-	if (valid_hooks & ~FILTER_VALID_HOOKS)
-		return -EINVAL;
-	return 0;
-}
-
 static const struct ebt_table frame_filter = {
 	.name		= "filter",
 	.table		= &initial_table,
 	.valid_hooks	= FILTER_VALID_HOOKS,
-	.check		= check,
 	.me		= THIS_MODULE,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/ebtable_nat.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/ebtable_nat.c
@@ -43,18 +43,10 @@
 	.entries	= (char *)initial_chains,
 };
 
-static int check(const struct ebt_table_info *info, unsigned int valid_hooks)
-{
-	if (valid_hooks & ~NAT_VALID_HOOKS)
-		return -EINVAL;
-	return 0;
-}
-
 static const struct ebt_table frame_nat = {
 	.name		= "nat",
 	.table		= &initial_table,
 	.valid_hooks	= NAT_VALID_HOOKS,
-	.check		= check,
 	.me		= THIS_MODULE,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/ebtables.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/ebtables.c
@@ -1040,9 +1040,10 @@
 		goto free_iterate;
 	}
 
-	/* the table doesn't like it */
-	if (t->check && (ret = t->check(newinfo, repl->valid_hooks)))
+	if (repl->valid_hooks != t->valid_hooks) {
+		ret = -EINVAL;
 		goto free_unlock;
+	}
 
 	if (repl->num_counters && repl->num_counters != t->private->nentries) {
 		ret = -EINVAL;
@@ -1089,7 +1090,7 @@
 
 	audit_log_nfcfg(repl->name, AF_BRIDGE, repl->nentries,
 			AUDIT_XT_OP_REPLACE, GFP_KERNEL);
-	return ret;
+	return 0;
 
 free_unlock:
 	mutex_unlock(&ebt_mutex);
@@ -1110,6 +1111,8 @@
 	struct ebt_table_info *newinfo;
 	struct ebt_replace tmp;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -1231,11 +1234,6 @@
 	if (ret != 0)
 		goto free_chainstack;
 
-	if (table->check && table->check(newinfo, table->valid_hooks)) {
-		ret = -EINVAL;
-		goto free_chainstack;
-	}
-
 	table->private = newinfo;
 	rwlock_init(&table->lock);
 	mutex_lock(&ebt_mutex);
@@ -1426,6 +1424,8 @@
 {
 	struct ebt_replace hlp;
 
+	if (len < sizeof(hlp))
+		return -EINVAL;
 	if (copy_from_sockptr(&hlp, arg, sizeof(hlp)))
 		return -EFAULT;
 
@@ -2118,8 +2118,7 @@
 		return ret;
 
 	offsets[0] = sizeof(struct ebt_entry); /* matches come first */
-	memcpy(&offsets[1], &entry->watchers_offset,
-			sizeof(offsets) - sizeof(offsets[0]));
+	memcpy(&offsets[1], &entry->offsets, sizeof(entry->offsets));
 
 	if (state->buf_kern_start) {
 		buf_start = state->buf_kern_start + state->buf_kern_offset;
@@ -2356,6 +2355,8 @@
 {
 	struct compat_ebt_replace hlp;
 
+	if (len < sizeof(hlp))
+		return -EINVAL;
 	if (copy_from_sockptr(&hlp, arg, sizeof(hlp)))
 		return -EFAULT;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/nf_conntrack_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/nf_conntrack_bridge.c
@@ -36,7 +36,7 @@
 	ktime_t tstamp = skb->tstamp;
 	struct ip_frag_state state;
 	struct iphdr *iph;
-	int err;
+	int err = 0;
 
 	/* for offloaded checksums cleanup checksum before fragmentation */
 	if (skb->ip_summed == CHECKSUM_PARTIAL &&
@@ -290,6 +290,36 @@
 	return nf_conntrack_in(skb, &bridge_state);
 }
 
+static unsigned int nf_ct_bridge_in(void *priv, struct sk_buff *skb,
+				    const struct nf_hook_state *state)
+{
+	bool promisc = BR_INPUT_SKB_CB(skb)->promisc;
+	struct nf_conntrack *nfct = skb_nfct(skb);
+	struct nf_conn *ct;
+
+	if (promisc) {
+		nf_reset_ct(skb);
+		return NF_ACCEPT;
+	}
+
+	if (!nfct || skb->pkt_type == PACKET_HOST)
+		return NF_ACCEPT;
+
+	/* nf_conntrack_confirm() cannot handle concurrent clones,
+	 * this happens for broad/multicast frames with e.g. macvlan on top
+	 * of the bridge device.
+	 */
+	ct = container_of(nfct, struct nf_conn, ct_general);
+	if (nf_ct_is_confirmed(ct) || nf_ct_is_template(ct))
+		return NF_ACCEPT;
+
+	/* let inet prerouting call conntrack again */
+	skb->_nfct = 0;
+	nf_ct_put(ct);
+
+	return NF_ACCEPT;
+}
+
 static void nf_ct_bridge_frag_save(struct sk_buff *skb,
 				   struct nf_bridge_frag_data *data)
 {
@@ -415,6 +445,12 @@
 		.priority	= NF_IP_PRI_CONNTRACK,
 	},
 	{
+		.hook		= nf_ct_bridge_in,
+		.pf		= NFPROTO_BRIDGE,
+		.hooknum	= NF_BR_LOCAL_IN,
+		.priority	= NF_IP_PRI_CONNTRACK_CONFIRM,
+	},
+	{
 		.hook		= nf_ct_bridge_post,
 		.pf		= NFPROTO_BRIDGE,
 		.hooknum	= NF_BR_POST_ROUTING,
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/nft_meta_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/nft_meta_bridge.c
@@ -53,7 +53,7 @@
 			goto err;
 
 		br_vlan_get_proto(br_dev, &p_proto);
-		nft_reg_store16(dest, htons(p_proto));
+		nft_reg_store_be16(dest, htons(p_proto));
 		return;
 	}
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/net/bridge/netfilter/nft_reject_bridge.c
+++ linux-xilinx-zynqmp-5.15.0/net/bridge/netfilter/nft_reject_bridge.c
@@ -49,7 +49,7 @@
 {
 	struct sk_buff *nskb;
 
-	nskb = nf_reject_skb_v4_tcp_reset(net, oldskb, dev, hook);
+	nskb = nf_reject_skb_v4_tcp_reset(net, oldskb, NULL, hook);
 	if (!nskb)
 		return;
 
@@ -65,7 +65,7 @@
 {
 	struct sk_buff *nskb;
 
-	nskb = nf_reject_skb_v4_unreach(net, oldskb, dev, hook, code);
+	nskb = nf_reject_skb_v4_unreach(net, oldskb, NULL, hook, code);
 	if (!nskb)
 		return;
 
@@ -81,7 +81,7 @@
 {
 	struct sk_buff *nskb;
 
-	nskb = nf_reject_skb_v6_tcp_reset(net, oldskb, dev, hook);
+	nskb = nf_reject_skb_v6_tcp_reset(net, oldskb, NULL, hook);
 	if (!nskb)
 		return;
 
@@ -98,7 +98,7 @@
 {
 	struct sk_buff *nskb;
 
-	nskb = nf_reject_skb_v6_unreach(net, oldskb, dev, hook, code);
+	nskb = nf_reject_skb_v6_unreach(net, oldskb, NULL, hook, code);
 	if (!nskb)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/caif/caif_socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/caif/caif_socket.c
@@ -1020,6 +1020,7 @@
 		return;
 	}
 	sk_stream_kill_queues(&cf_sk->sk);
+	WARN_ON(sk->sk_forward_alloc);
 	caif_free_client(&cf_sk->layer);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/caif/caif_usb.c
+++ linux-xilinx-zynqmp-5.15.0/net/caif/caif_usb.c
@@ -134,6 +134,9 @@
 	struct usb_device *usbdev;
 	int res;
 
+	if (what == NETDEV_UNREGISTER && dev->reg_state >= NETREG_UNREGISTERED)
+		return 0;
+
 	/* Check whether we have a NCM device, and find its VID/PID. */
 	if (!(dev->dev.parent && dev->dev.parent->driver &&
 	      strcmp(dev->dev.parent->driver->name, "cdc_ncm") == 0))
--- linux-xilinx-zynqmp-5.15.0.orig/net/caif/cfctrl.c
+++ linux-xilinx-zynqmp-5.15.0/net/caif/cfctrl.c
@@ -269,11 +269,15 @@
 	default:
 		pr_warn("Request setup of bad link type = %d\n",
 			param->linktype);
+		cfpkt_destroy(pkt);
 		return -EINVAL;
 	}
 	req = kzalloc(sizeof(*req), GFP_KERNEL);
-	if (!req)
+	if (!req) {
+		cfpkt_destroy(pkt);
 		return -ENOMEM;
+	}
+
 	req->client_layer = user_layer;
 	req->cmd = CFCTRL_CMD_LINK_SETUP;
 	req->param = *param;
--- linux-xilinx-zynqmp-5.15.0.orig/net/caif/chnl_net.c
+++ linux-xilinx-zynqmp-5.15.0/net/caif/chnl_net.c
@@ -310,9 +310,6 @@
 
 	if (result == 0) {
 		pr_debug("connect timeout\n");
-		caif_disconnect_client(dev_net(dev), &priv->chnl);
-		priv->state = CAIF_DISCONNECTED;
-		pr_debug("state disconnected\n");
 		result = -ETIMEDOUT;
 		goto error;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/af_can.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/af_can.c
@@ -171,6 +171,7 @@
 		/* release sk on errors */
 		sock_orphan(sk);
 		sock_put(sk);
+		sock->sk = NULL;
 	}
 
  errout:
@@ -287,8 +288,8 @@
 		netif_rx_ni(newskb);
 
 	/* update statistics */
-	pkg_stats->tx_frames++;
-	pkg_stats->tx_frames_delta++;
+	atomic_long_inc(&pkg_stats->tx_frames);
+	atomic_long_inc(&pkg_stats->tx_frames_delta);
 
 	return 0;
 
@@ -451,7 +452,7 @@
 
 	/* insert new receiver  (dev,canid,mask) -> (func,data) */
 
-	if (dev && dev->type != ARPHRD_CAN)
+	if (dev && (dev->type != ARPHRD_CAN || !can_get_ml_priv(dev)))
 		return -ENODEV;
 
 	if (dev && !net_eq(net, dev_net(dev)))
@@ -648,8 +649,8 @@
 	int matches;
 
 	/* update statistics */
-	pkg_stats->rx_frames++;
-	pkg_stats->rx_frames_delta++;
+	atomic_long_inc(&pkg_stats->rx_frames);
+	atomic_long_inc(&pkg_stats->rx_frames_delta);
 
 	/* create non-zero unique skb identifier together with *skb */
 	while (!(can_skb_prv(skb)->skbcnt))
@@ -670,8 +671,8 @@
 	consume_skb(skb);
 
 	if (matches > 0) {
-		pkg_stats->matches++;
-		pkg_stats->matches_delta++;
+		atomic_long_inc(&pkg_stats->matches);
+		atomic_long_inc(&pkg_stats->matches_delta);
 	}
 }
 
@@ -680,7 +681,7 @@
 {
 	struct canfd_frame *cfd = (struct canfd_frame *)skb->data;
 
-	if (unlikely(dev->type != ARPHRD_CAN || skb->len != CAN_MTU)) {
+	if (unlikely(dev->type != ARPHRD_CAN || !can_get_ml_priv(dev) || skb->len != CAN_MTU)) {
 		pr_warn_once("PF_CAN: dropped non conform CAN skbuff: dev type %d, len %d\n",
 			     dev->type, skb->len);
 		goto free_skb;
@@ -706,7 +707,7 @@
 {
 	struct canfd_frame *cfd = (struct canfd_frame *)skb->data;
 
-	if (unlikely(dev->type != ARPHRD_CAN || skb->len != CANFD_MTU)) {
+	if (unlikely(dev->type != ARPHRD_CAN || !can_get_ml_priv(dev) || skb->len != CANFD_MTU)) {
 		pr_warn_once("PF_CAN: dropped non conform CAN FD skbuff: dev type %d, len %d\n",
 			     dev->type, skb->len);
 		goto free_skb;
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/af_can.h
+++ linux-xilinx-zynqmp-5.15.0/net/can/af_can.h
@@ -66,9 +66,9 @@
 struct can_pkg_stats {
 	unsigned long jiffies_init;
 
-	unsigned long rx_frames;
-	unsigned long tx_frames;
-	unsigned long matches;
+	atomic_long_t rx_frames;
+	atomic_long_t tx_frames;
+	atomic_long_t matches;
 
 	unsigned long total_rx_rate;
 	unsigned long total_tx_rate;
@@ -82,9 +82,9 @@
 	unsigned long max_tx_rate;
 	unsigned long max_rx_match_ratio;
 
-	unsigned long rx_frames_delta;
-	unsigned long tx_frames_delta;
-	unsigned long matches_delta;
+	atomic_long_t rx_frames_delta;
+	atomic_long_t tx_frames_delta;
+	atomic_long_t matches_delta;
 };
 
 /* persistent statistics */
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/bcm.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/bcm.c
@@ -100,6 +100,7 @@
 
 struct bcm_op {
 	struct list_head list;
+	struct rcu_head rcu;
 	int ifindex;
 	canid_t can_id;
 	u32 flags;
@@ -273,6 +274,7 @@
 	struct sk_buff *skb;
 	struct net_device *dev;
 	struct canfd_frame *cf = op->frames + op->cfsiz * op->currframe;
+	int err;
 
 	/* no target device? => exit */
 	if (!op->ifindex)
@@ -297,11 +299,11 @@
 	/* send with loopback */
 	skb->dev = dev;
 	can_skb_set_owner(skb, op->sk);
-	can_send(skb, 1);
+	err = can_send(skb, 1);
+	if (!err)
+		op->frames_abs++;
 
-	/* update statistics */
 	op->currframe++;
-	op->frames_abs++;
 
 	/* reached last frame? */
 	if (op->currframe >= op->nframes)
@@ -718,10 +720,9 @@
 	return NULL;
 }
 
-static void bcm_remove_op(struct bcm_op *op)
+static void bcm_free_op_rcu(struct rcu_head *rcu_head)
 {
-	hrtimer_cancel(&op->timer);
-	hrtimer_cancel(&op->thrtimer);
+	struct bcm_op *op = container_of(rcu_head, struct bcm_op, rcu);
 
 	if ((op->frames) && (op->frames != &op->sframe))
 		kfree(op->frames);
@@ -732,6 +733,14 @@
 	kfree(op);
 }
 
+static void bcm_remove_op(struct bcm_op *op)
+{
+	hrtimer_cancel(&op->timer);
+	hrtimer_cancel(&op->thrtimer);
+
+	call_rcu(&op->rcu, bcm_free_op_rcu);
+}
+
 static void bcm_rx_unreg(struct net_device *dev, struct bcm_op *op)
 {
 	if (op->rx_reg_dev == dev) {
@@ -757,6 +766,9 @@
 		if ((op->can_id == mh->can_id) && (op->ifindex == ifindex) &&
 		    (op->flags & CAN_FD_FRAME) == (mh->flags & CAN_FD_FRAME)) {
 
+			/* disable automatic timer on frame reception */
+			op->flags |= RX_NO_AUTOTIMER;
+
 			/*
 			 * Don't care if we're bound or not (due to netdev
 			 * problems) can_rx_unregister() is always a save
@@ -785,7 +797,6 @@
 						  bcm_rx_handler, op);
 
 			list_del(&op->list);
-			synchronize_rcu();
 			bcm_remove_op(op);
 			return 1; /* done */
 		}
@@ -925,6 +936,8 @@
 
 			cf = op->frames + op->cfsiz * i;
 			err = memcpy_from_msg((u8 *)cf, msg, op->cfsiz);
+			if (err < 0)
+				goto free_op;
 
 			if (op->flags & CAN_FD_FRAME) {
 				if (cf->len > 64)
@@ -934,12 +947,8 @@
 					err = -EINVAL;
 			}
 
-			if (err < 0) {
-				if (op->frames != &op->sframe)
-					kfree(op->frames);
-				kfree(op);
-				return err;
-			}
+			if (err < 0)
+				goto free_op;
 
 			if (msg_head->flags & TX_CP_CAN_ID) {
 				/* copy can_id into frame */
@@ -1010,6 +1019,12 @@
 		bcm_tx_start_timer(op);
 
 	return msg_head->nframes * op->cfsiz + MHSIZ;
+
+free_op:
+	if (op->frames != &op->sframe)
+		kfree(op->frames);
+	kfree(op);
+	return err;
 }
 
 /*
@@ -1408,6 +1423,12 @@
 
 		/* remove device reference, if this is our bound device */
 		if (bo->bound && bo->ifindex == dev->ifindex) {
+#if IS_ENABLED(CONFIG_PROC_FS)
+			if (sock_net(sk)->can.bcmproc_dir && bo->bcm_proc_read) {
+				remove_proc_entry(bo->procname, sock_net(sk)->can.bcmproc_dir);
+				bo->bcm_proc_read = NULL;
+			}
+#endif
 			bo->bound   = 0;
 			bo->ifindex = 0;
 			notify_enodev = 1;
@@ -1506,6 +1527,12 @@
 
 	lock_sock(sk);
 
+#if IS_ENABLED(CONFIG_PROC_FS)
+	/* remove procfs entry */
+	if (net->can.bcmproc_dir && bo->bcm_proc_read)
+		remove_proc_entry(bo->procname, net->can.bcmproc_dir);
+#endif /* CONFIG_PROC_FS */
+
 	list_for_each_entry_safe(op, next, &bo->tx_ops, list)
 		bcm_remove_op(op);
 
@@ -1541,12 +1568,6 @@
 	list_for_each_entry_safe(op, next, &bo->rx_ops, list)
 		bcm_remove_op(op);
 
-#if IS_ENABLED(CONFIG_PROC_FS)
-	/* remove procfs entry */
-	if (net->can.bcmproc_dir && bo->bcm_proc_read)
-		remove_proc_entry(bo->procname, net->can.bcmproc_dir);
-#endif /* CONFIG_PROC_FS */
-
 	/* remove device reference */
 	if (bo->bound) {
 		bo->bound   = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/isotp.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/isotp.c
@@ -14,7 +14,6 @@
  * - use CAN_ISOTP_WAIT_TX_DONE flag to block the caller until the PDU is sent
  * - as we have static buffers the check whether the PDU fits into the buffer
  *   is done at FF reception time (no support for sending 'wait frames')
- * - take care of the tx-queue-len as traffic shaping is still on the TODO list
  *
  * Copyright (c) 2020 Volkswagen Group Electronic Research
  * All rights reserved.
@@ -56,6 +55,7 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
+#include <linux/spinlock.h>
 #include <linux/hrtimer.h>
 #include <linux/wait.h>
 #include <linux/uio.h>
@@ -86,9 +86,9 @@
 /* ISO 15765-2:2016 supports more than 4095 byte per ISO PDU as the FF_DL can
  * take full 32 bit values (4 Gbyte). We would need some good concept to handle
  * this between user space and kernel space. For now increase the static buffer
- * to something about 8 kbyte to be able to test this new functionality.
+ * to something about 64 kbyte to be able to test this new functionality.
  */
-#define MAX_MSG_LENGTH 8200
+#define MAX_MSG_LENGTH 66000
 
 /* N_PCI type values in bits 7-4 of N_PCI bytes */
 #define N_PCI_SF 0x00	/* single frame */
@@ -104,23 +104,28 @@
 #define FC_CONTENT_SZ 3	/* flow control content size in byte (FS/BS/STmin) */
 
 #define ISOTP_CHECK_PADDING (CAN_ISOTP_CHK_PAD_LEN | CAN_ISOTP_CHK_PAD_DATA)
+#define ISOTP_ALL_BC_FLAGS (CAN_ISOTP_SF_BROADCAST | CAN_ISOTP_CF_BROADCAST)
 
 /* Flow Status given in FC frame */
 #define ISOTP_FC_CTS 0		/* clear to send */
 #define ISOTP_FC_WT 1		/* wait */
 #define ISOTP_FC_OVFLW 2	/* overflow */
 
+#define ISOTP_FC_TIMEOUT 1	/* 1 sec */
+#define ISOTP_ECHO_TIMEOUT 2	/* 2 secs */
+
 enum {
 	ISOTP_IDLE = 0,
 	ISOTP_WAIT_FIRST_FC,
 	ISOTP_WAIT_FC,
 	ISOTP_WAIT_DATA,
-	ISOTP_SENDING
+	ISOTP_SENDING,
+	ISOTP_SHUTDOWN,
 };
 
 struct tpcon {
-	int idx;
-	int len;
+	unsigned int idx;
+	unsigned int len;
 	u32 state;
 	u8 bs;
 	u8 sn;
@@ -136,15 +141,18 @@
 	canid_t rxid;
 	ktime_t tx_gap;
 	ktime_t lastrxcf_tstamp;
-	struct hrtimer rxtimer, txtimer;
+	struct hrtimer rxtimer, txtimer, txfrtimer;
 	struct can_isotp_options opt;
 	struct can_isotp_fc_options rxfc, txfc;
 	struct can_isotp_ll_options ll;
+	u32 frame_txtime;
 	u32 force_tx_stmin;
 	u32 force_rx_stmin;
+	u32 cfecho; /* consecutive frame echo tag */
 	struct tpcon rx, tx;
 	struct list_head notifier;
 	wait_queue_head_t wait;
+	spinlock_t rx_lock; /* protect single thread state machine */
 };
 
 static LIST_HEAD(isotp_notifier_list);
@@ -156,6 +164,17 @@
 	return (struct isotp_sock *)sk;
 }
 
+static u32 isotp_bc_flags(struct isotp_sock *so)
+{
+	return so->opt.flags & ISOTP_ALL_BC_FLAGS;
+}
+
+static bool isotp_register_rxid(struct isotp_sock *so)
+{
+	/* no broadcast modes => register rx_id for FC frame reception */
+	return (isotp_bc_flags(so) == 0);
+}
+
 static enum hrtimer_restart isotp_rx_timer_handler(struct hrtimer *hrtimer)
 {
 	struct isotp_sock *so = container_of(hrtimer, struct isotp_sock,
@@ -237,7 +256,8 @@
 	so->lastrxcf_tstamp = ktime_set(0, 0);
 
 	/* start rx timeout watchdog */
-	hrtimer_start(&so->rxtimer, ktime_set(1, 0), HRTIMER_MODE_REL_SOFT);
+	hrtimer_start(&so->rxtimer, ktime_set(ISOTP_FC_TIMEOUT, 0),
+		      HRTIMER_MODE_REL_SOFT);
 	return 0;
 }
 
@@ -323,6 +343,8 @@
 	return 0;
 }
 
+static void isotp_send_cframe(struct isotp_sock *so);
+
 static int isotp_rcv_fc(struct isotp_sock *so, struct canfd_frame *cf, int ae)
 {
 	struct sock *sk = &so->sk;
@@ -358,7 +380,7 @@
 
 		so->tx_gap = ktime_set(0, 0);
 		/* add transmission time for CAN frame N_As */
-		so->tx_gap = ktime_add_ns(so->tx_gap, so->opt.frame_txtime);
+		so->tx_gap = ktime_add_ns(so->tx_gap, so->frame_txtime);
 		/* add waiting time for consecutive frames N_Cs */
 		if (so->opt.flags & CAN_ISOTP_FORCE_TXSTMIN)
 			so->tx_gap = ktime_add_ns(so->tx_gap,
@@ -377,14 +399,15 @@
 	case ISOTP_FC_CTS:
 		so->tx.bs = 0;
 		so->tx.state = ISOTP_SENDING;
-		/* start cyclic timer for sending CF frame */
-		hrtimer_start(&so->txtimer, so->tx_gap,
+		/* send CF frame and enable echo timeout handling */
+		hrtimer_start(&so->txtimer, ktime_set(ISOTP_ECHO_TIMEOUT, 0),
 			      HRTIMER_MODE_REL_SOFT);
+		isotp_send_cframe(so);
 		break;
 
 	case ISOTP_FC_WT:
 		/* start timer to wait for next FC frame */
-		hrtimer_start(&so->txtimer, ktime_set(1, 0),
+		hrtimer_start(&so->txtimer, ktime_set(ISOTP_FC_TIMEOUT, 0),
 			      HRTIMER_MODE_REL_SOFT);
 		break;
 
@@ -579,7 +602,7 @@
 	/* perform blocksize handling, if enabled */
 	if (!so->rxfc.bs || ++so->rx.bs < so->rxfc.bs) {
 		/* start rx timeout watchdog */
-		hrtimer_start(&so->rxtimer, ktime_set(1, 0),
+		hrtimer_start(&so->rxtimer, ktime_set(ISOTP_FC_TIMEOUT, 0),
 			      HRTIMER_MODE_REL_SOFT);
 		return 0;
 	}
@@ -615,11 +638,17 @@
 
 	n_pci_type = cf->data[ae] & 0xF0;
 
+	/* Make sure the state changes and data structures stay consistent at
+	 * CAN frame reception time. This locking is not needed in real world
+	 * use cases but the inconsistency can be triggered with syzkaller.
+	 */
+	spin_lock(&so->rx_lock);
+
 	if (so->opt.flags & CAN_ISOTP_HALF_DUPLEX) {
 		/* check rx/tx path half duplex expectations */
 		if ((so->tx.state != ISOTP_IDLE && n_pci_type != N_PCI_FC) ||
 		    (so->rx.state != ISOTP_IDLE && n_pci_type == N_PCI_FC))
-			return;
+			goto out_unlock;
 	}
 
 	switch (n_pci_type) {
@@ -668,6 +697,9 @@
 		isotp_rcv_cf(sk, cf, ae, skb);
 		break;
 	}
+
+out_unlock:
+	spin_unlock(&so->rx_lock);
 }
 
 static void isotp_fill_dataframe(struct canfd_frame *cf, struct isotp_sock *so,
@@ -701,6 +733,63 @@
 		cf->data[0] = so->opt.ext_address;
 }
 
+static void isotp_send_cframe(struct isotp_sock *so)
+{
+	struct sock *sk = &so->sk;
+	struct sk_buff *skb;
+	struct net_device *dev;
+	struct canfd_frame *cf;
+	int can_send_ret;
+	int ae = (so->opt.flags & CAN_ISOTP_EXTEND_ADDR) ? 1 : 0;
+
+	dev = dev_get_by_index(sock_net(sk), so->ifindex);
+	if (!dev)
+		return;
+
+	skb = alloc_skb(so->ll.mtu + sizeof(struct can_skb_priv), GFP_ATOMIC);
+	if (!skb) {
+		dev_put(dev);
+		return;
+	}
+
+	can_skb_reserve(skb);
+	can_skb_prv(skb)->ifindex = dev->ifindex;
+	can_skb_prv(skb)->skbcnt = 0;
+
+	cf = (struct canfd_frame *)skb->data;
+	skb_put_zero(skb, so->ll.mtu);
+
+	/* create consecutive frame */
+	isotp_fill_dataframe(cf, so, ae, 0);
+
+	/* place consecutive frame N_PCI in appropriate index */
+	cf->data[ae] = N_PCI_CF | so->tx.sn++;
+	so->tx.sn %= 16;
+	so->tx.bs++;
+
+	cf->flags = so->ll.tx_flags;
+
+	skb->dev = dev;
+	can_skb_set_owner(skb, sk);
+
+	/* cfecho should have been zero'ed by init/isotp_rcv_echo() */
+	if (so->cfecho)
+		pr_notice_once("can-isotp: cfecho is %08X != 0\n", so->cfecho);
+
+	/* set consecutive frame echo tag */
+	so->cfecho = *(u32 *)cf->data;
+
+	/* send frame with local echo enabled */
+	can_send_ret = can_send(skb, 1);
+	if (can_send_ret) {
+		pr_notice_once("can-isotp: %s: can_send_ret %pe\n",
+			       __func__, ERR_PTR(can_send_ret));
+		if (can_send_ret == -ENOBUFS)
+			pr_notice_once("can-isotp: tx queue is full\n");
+	}
+	dev_put(dev);
+}
+
 static void isotp_create_fframe(struct canfd_frame *cf, struct isotp_sock *so,
 				int ae)
 {
@@ -734,176 +823,152 @@
 		cf->data[i] = so->tx.buf[so->tx.idx++];
 
 	so->tx.sn = 1;
-	so->tx.state = ISOTP_WAIT_FIRST_FC;
 }
 
-static enum hrtimer_restart isotp_tx_timer_handler(struct hrtimer *hrtimer)
+static void isotp_rcv_echo(struct sk_buff *skb, void *data)
 {
-	struct isotp_sock *so = container_of(hrtimer, struct isotp_sock,
-					     txtimer);
-	struct sock *sk = &so->sk;
-	struct sk_buff *skb;
-	struct net_device *dev;
-	struct canfd_frame *cf;
-	enum hrtimer_restart restart = HRTIMER_NORESTART;
-	int can_send_ret;
-	int ae = (so->opt.flags & CAN_ISOTP_EXTEND_ADDR) ? 1 : 0;
+	struct sock *sk = (struct sock *)data;
+	struct isotp_sock *so = isotp_sk(sk);
+	struct canfd_frame *cf = (struct canfd_frame *)skb->data;
 
-	switch (so->tx.state) {
-	case ISOTP_WAIT_FC:
-	case ISOTP_WAIT_FIRST_FC:
+	/* only handle my own local echo CF/SF skb's (no FF!) */
+	if (skb->sk != sk || so->cfecho != *(u32 *)cf->data)
+		return;
 
-		/* we did not get any flow control frame in time */
+	/* cancel local echo timeout */
+	hrtimer_cancel(&so->txtimer);
 
-		/* report 'communication error on send' */
-		sk->sk_err = ECOMM;
-		if (!sock_flag(sk, SOCK_DEAD))
-			sk_error_report(sk);
+	/* local echo skb with consecutive frame has been consumed */
+	so->cfecho = 0;
 
-		/* reset tx state */
+	if (so->tx.idx >= so->tx.len) {
+		/* we are done */
 		so->tx.state = ISOTP_IDLE;
 		wake_up_interruptible(&so->wait);
-		break;
+		return;
+	}
 
-	case ISOTP_SENDING:
+	if (so->txfc.bs && so->tx.bs >= so->txfc.bs) {
+		/* stop and wait for FC with timeout */
+		so->tx.state = ISOTP_WAIT_FC;
+		hrtimer_start(&so->txtimer, ktime_set(ISOTP_FC_TIMEOUT, 0),
+			      HRTIMER_MODE_REL_SOFT);
+		return;
+	}
 
-		/* push out the next segmented pdu */
-		dev = dev_get_by_index(sock_net(sk), so->ifindex);
-		if (!dev)
-			break;
+	/* no gap between data frames needed => use burst mode */
+	if (!so->tx_gap) {
+		/* enable echo timeout handling */
+		hrtimer_start(&so->txtimer, ktime_set(ISOTP_ECHO_TIMEOUT, 0),
+			      HRTIMER_MODE_REL_SOFT);
+		isotp_send_cframe(so);
+		return;
+	}
 
-isotp_tx_burst:
-		skb = alloc_skb(so->ll.mtu + sizeof(struct can_skb_priv),
-				GFP_ATOMIC);
-		if (!skb) {
-			dev_put(dev);
-			break;
-		}
+	/* start timer to send next consecutive frame with correct delay */
+	hrtimer_start(&so->txfrtimer, so->tx_gap, HRTIMER_MODE_REL_SOFT);
+}
 
-		can_skb_reserve(skb);
-		can_skb_prv(skb)->ifindex = dev->ifindex;
-		can_skb_prv(skb)->skbcnt = 0;
-
-		cf = (struct canfd_frame *)skb->data;
-		skb_put_zero(skb, so->ll.mtu);
-
-		/* create consecutive frame */
-		isotp_fill_dataframe(cf, so, ae, 0);
-
-		/* place consecutive frame N_PCI in appropriate index */
-		cf->data[ae] = N_PCI_CF | so->tx.sn++;
-		so->tx.sn %= 16;
-		so->tx.bs++;
-
-		cf->flags = so->ll.tx_flags;
-
-		skb->dev = dev;
-		can_skb_set_owner(skb, sk);
-
-		can_send_ret = can_send(skb, 1);
-		if (can_send_ret) {
-			pr_notice_once("can-isotp: %s: can_send_ret %pe\n",
-				       __func__, ERR_PTR(can_send_ret));
-			if (can_send_ret == -ENOBUFS)
-				pr_notice_once("can-isotp: tx queue is full, increasing txqueuelen may prevent this error\n");
-		}
-		if (so->tx.idx >= so->tx.len) {
-			/* we are done */
-			so->tx.state = ISOTP_IDLE;
-			dev_put(dev);
-			wake_up_interruptible(&so->wait);
-			break;
-		}
+static enum hrtimer_restart isotp_tx_timer_handler(struct hrtimer *hrtimer)
+{
+	struct isotp_sock *so = container_of(hrtimer, struct isotp_sock,
+					     txtimer);
+	struct sock *sk = &so->sk;
 
-		if (so->txfc.bs && so->tx.bs >= so->txfc.bs) {
-			/* stop and wait for FC */
-			so->tx.state = ISOTP_WAIT_FC;
-			dev_put(dev);
-			hrtimer_set_expires(&so->txtimer,
-					    ktime_add(ktime_get(),
-						      ktime_set(1, 0)));
-			restart = HRTIMER_RESTART;
-			break;
-		}
+	/* don't handle timeouts in IDLE or SHUTDOWN state */
+	if (so->tx.state == ISOTP_IDLE || so->tx.state == ISOTP_SHUTDOWN)
+		return HRTIMER_NORESTART;
+
+	/* we did not get any flow control or echo frame in time */
+
+	/* report 'communication error on send' */
+	sk->sk_err = ECOMM;
+	if (!sock_flag(sk, SOCK_DEAD))
+		sk_error_report(sk);
 
-		/* no gap between data frames needed => use burst mode */
-		if (!so->tx_gap)
-			goto isotp_tx_burst;
+	/* reset tx state */
+	so->tx.state = ISOTP_IDLE;
+	wake_up_interruptible(&so->wait);
 
-		/* start timer to send next data frame with correct delay */
-		dev_put(dev);
-		hrtimer_set_expires(&so->txtimer,
-				    ktime_add(ktime_get(), so->tx_gap));
-		restart = HRTIMER_RESTART;
-		break;
+	return HRTIMER_NORESTART;
+}
 
-	default:
-		WARN_ON_ONCE(1);
-	}
+static enum hrtimer_restart isotp_txfr_timer_handler(struct hrtimer *hrtimer)
+{
+	struct isotp_sock *so = container_of(hrtimer, struct isotp_sock,
+					     txfrtimer);
 
-	return restart;
+	/* start echo timeout handling and cover below protocol error */
+	hrtimer_start(&so->txtimer, ktime_set(ISOTP_ECHO_TIMEOUT, 0),
+		      HRTIMER_MODE_REL_SOFT);
+
+	/* cfecho should be consumed by isotp_rcv_echo() here */
+	if (so->tx.state == ISOTP_SENDING && !so->cfecho)
+		isotp_send_cframe(so);
+
+	return HRTIMER_NORESTART;
 }
 
 static int isotp_sendmsg(struct socket *sock, struct msghdr *msg, size_t size)
 {
 	struct sock *sk = sock->sk;
 	struct isotp_sock *so = isotp_sk(sk);
-	u32 old_state = so->tx.state;
 	struct sk_buff *skb;
 	struct net_device *dev;
 	struct canfd_frame *cf;
 	int ae = (so->opt.flags & CAN_ISOTP_EXTEND_ADDR) ? 1 : 0;
 	int wait_tx_done = (so->opt.flags & CAN_ISOTP_WAIT_TX_DONE) ? 1 : 0;
+	s64 hrtimer_sec = ISOTP_ECHO_TIMEOUT;
 	int off;
 	int err;
 
-	if (!so->bound)
+	if (!so->bound || so->tx.state == ISOTP_SHUTDOWN)
 		return -EADDRNOTAVAIL;
 
-	/* we do not support multiple buffers - for now */
-	if (cmpxchg(&so->tx.state, ISOTP_IDLE, ISOTP_SENDING) != ISOTP_IDLE ||
-	    wq_has_sleeper(&so->wait)) {
-		if (msg->msg_flags & MSG_DONTWAIT) {
-			err = -EAGAIN;
-			goto err_out;
-		}
+	while (cmpxchg(&so->tx.state, ISOTP_IDLE, ISOTP_SENDING) != ISOTP_IDLE) {
+		/* we do not support multiple buffers - for now */
+		if (msg->msg_flags & MSG_DONTWAIT)
+			return -EAGAIN;
+
+		if (so->tx.state == ISOTP_SHUTDOWN)
+			return -EADDRNOTAVAIL;
 
 		/* wait for complete transmission of current pdu */
 		err = wait_event_interruptible(so->wait, so->tx.state == ISOTP_IDLE);
 		if (err)
-			goto err_out;
+			goto err_event_drop;
 	}
 
 	if (!size || size > MAX_MSG_LENGTH) {
 		err = -EINVAL;
-		goto err_out;
+		goto err_out_drop;
 	}
 
 	/* take care of a potential SF_DL ESC offset for TX_DL > 8 */
 	off = (so->tx.ll_dl > CAN_MAX_DLEN) ? 1 : 0;
 
 	/* does the given data fit into a single frame for SF_BROADCAST? */
-	if ((so->opt.flags & CAN_ISOTP_SF_BROADCAST) &&
+	if ((isotp_bc_flags(so) == CAN_ISOTP_SF_BROADCAST) &&
 	    (size > so->tx.ll_dl - SF_PCI_SZ4 - ae - off)) {
 		err = -EINVAL;
-		goto err_out;
+		goto err_out_drop;
 	}
 
 	err = memcpy_from_msg(so->tx.buf, msg, size);
 	if (err < 0)
-		goto err_out;
+		goto err_out_drop;
 
 	dev = dev_get_by_index(sock_net(sk), so->ifindex);
 	if (!dev) {
 		err = -ENXIO;
-		goto err_out;
+		goto err_out_drop;
 	}
 
 	skb = sock_alloc_send_skb(sk, so->ll.mtu + sizeof(struct can_skb_priv),
 				  msg->msg_flags & MSG_DONTWAIT, &err);
 	if (!skb) {
 		dev_put(dev);
-		goto err_out;
+		goto err_out_drop;
 	}
 
 	can_skb_reserve(skb);
@@ -916,6 +981,10 @@
 	cf = (struct canfd_frame *)skb->data;
 	skb_put_zero(skb, so->ll.mtu);
 
+	/* cfecho should have been zero'ed by init / former isotp_rcv_echo() */
+	if (so->cfecho)
+		pr_notice_once("can-isotp: uninit cfecho %08X\n", so->cfecho);
+
 	/* check for single frame transmission depending on TX_DL */
 	if (size <= so->tx.ll_dl - SF_PCI_SZ4 - ae - off) {
 		/* The message size generally fits into a SingleFrame - good.
@@ -941,20 +1010,40 @@
 		else
 			cf->data[ae] |= size;
 
-		so->tx.state = ISOTP_IDLE;
-		wake_up_interruptible(&so->wait);
-
-		/* don't enable wait queue for a single frame transmission */
-		wait_tx_done = 0;
+		/* set CF echo tag for isotp_rcv_echo() (SF-mode) */
+		so->cfecho = *(u32 *)cf->data;
 	} else {
-		/* send first frame and wait for FC */
+		/* send first frame */
 
 		isotp_create_fframe(cf, so, ae);
 
-		/* start timeout for FC */
-		hrtimer_start(&so->txtimer, ktime_set(1, 0), HRTIMER_MODE_REL_SOFT);
+		if (isotp_bc_flags(so) == CAN_ISOTP_CF_BROADCAST) {
+			/* set timer for FC-less operation (STmin = 0) */
+			if (so->opt.flags & CAN_ISOTP_FORCE_TXSTMIN)
+				so->tx_gap = ktime_set(0, so->force_tx_stmin);
+			else
+				so->tx_gap = ktime_set(0, so->frame_txtime);
+
+			/* disable wait for FCs due to activated block size */
+			so->txfc.bs = 0;
+
+			/* set CF echo tag for isotp_rcv_echo() (CF-mode) */
+			so->cfecho = *(u32 *)cf->data;
+		} else {
+			/* standard flow control check */
+			so->tx.state = ISOTP_WAIT_FIRST_FC;
+
+			/* start timeout for FC */
+			hrtimer_sec = ISOTP_FC_TIMEOUT;
+
+			/* no CF echo tag for isotp_rcv_echo() (FF-mode) */
+			so->cfecho = 0;
+		}
 	}
 
+	hrtimer_start(&so->txtimer, ktime_set(hrtimer_sec, 0),
+		      HRTIMER_MODE_REL_SOFT);
+
 	/* send the first or only CAN frame */
 	cf->flags = so->ll.tx_flags;
 
@@ -965,23 +1054,38 @@
 	if (err) {
 		pr_notice_once("can-isotp: %s: can_send_ret %pe\n",
 			       __func__, ERR_PTR(err));
-		goto err_out;
+
+		/* no transmission -> no timeout monitoring */
+		hrtimer_cancel(&so->txtimer);
+
+		/* reset consecutive frame echo tag */
+		so->cfecho = 0;
+
+		goto err_out_drop;
 	}
 
 	if (wait_tx_done) {
 		/* wait for complete transmission of current pdu */
-		wait_event_interruptible(so->wait, so->tx.state == ISOTP_IDLE);
+		err = wait_event_interruptible(so->wait, so->tx.state == ISOTP_IDLE);
+		if (err)
+			goto err_event_drop;
 
-		if (sk->sk_err)
-			return -sk->sk_err;
+		err = sock_error(sk);
+		if (err)
+			return err;
 	}
 
 	return size;
 
-err_out:
-	so->tx.state = old_state;
-	if (so->tx.state == ISOTP_IDLE)
-		wake_up_interruptible(&so->wait);
+err_event_drop:
+	/* got signal: force tx state machine to be idle */
+	so->tx.state = ISOTP_IDLE;
+	hrtimer_cancel(&so->txfrtimer);
+	hrtimer_cancel(&so->txtimer);
+err_out_drop:
+	/* drop this PDU and unlock a potential wait queue */
+	so->tx.state = ISOTP_IDLE;
+	wake_up_interruptible(&so->wait);
 
 	return err;
 }
@@ -991,26 +1095,29 @@
 {
 	struct sock *sk = sock->sk;
 	struct sk_buff *skb;
-	int err = 0;
-	int noblock;
+	struct isotp_sock *so = isotp_sk(sk);
+	int noblock = flags & MSG_DONTWAIT;
+	int ret = 0;
 
-	noblock = flags & MSG_DONTWAIT;
-	flags &= ~MSG_DONTWAIT;
+	if (flags & ~(MSG_DONTWAIT | MSG_TRUNC | MSG_PEEK | MSG_CMSG_COMPAT))
+		return -EINVAL;
 
-	skb = skb_recv_datagram(sk, flags, noblock, &err);
+	if (!so->bound)
+		return -EADDRNOTAVAIL;
+
+	flags &= ~MSG_DONTWAIT;
+	skb = skb_recv_datagram(sk, flags, noblock, &ret);
 	if (!skb)
-		return err;
+		return ret;
 
 	if (size < skb->len)
 		msg->msg_flags |= MSG_TRUNC;
 	else
 		size = skb->len;
 
-	err = memcpy_to_msg(msg, skb->data, size);
-	if (err < 0) {
-		skb_free_datagram(sk, skb);
-		return err;
-	}
+	ret = memcpy_to_msg(msg, skb->data, size);
+	if (ret < 0)
+		goto out_err;
 
 	sock_recv_timestamp(msg, sk, skb);
 
@@ -1020,9 +1127,13 @@
 		memcpy(msg->msg_name, skb->cb, msg->msg_namelen);
 	}
 
+	/* set length of return value */
+	ret = (flags & MSG_TRUNC) ? skb->len : size;
+
+out_err:
 	skb_free_datagram(sk, skb);
 
-	return size;
+	return ret;
 }
 
 static int isotp_release(struct socket *sock)
@@ -1038,7 +1149,13 @@
 	net = sock_net(sk);
 
 	/* wait for complete transmission of current pdu */
-	wait_event_interruptible(so->wait, so->tx.state == ISOTP_IDLE);
+	while (wait_event_interruptible(so->wait, so->tx.state == ISOTP_IDLE) == 0 &&
+	       cmpxchg(&so->tx.state, ISOTP_IDLE, ISOTP_SHUTDOWN) != ISOTP_IDLE)
+		;
+
+	/* force state machines to be idle also when a signal occurred */
+	so->tx.state = ISOTP_SHUTDOWN;
+	so->rx.state = ISOTP_IDLE;
 
 	spin_lock(&isotp_notifier_lock);
 	while (isotp_busy_notifier == so) {
@@ -1052,21 +1169,27 @@
 	lock_sock(sk);
 
 	/* remove current filters & unregister */
-	if (so->bound && (!(so->opt.flags & CAN_ISOTP_SF_BROADCAST))) {
+	if (so->bound) {
 		if (so->ifindex) {
 			struct net_device *dev;
 
 			dev = dev_get_by_index(net, so->ifindex);
 			if (dev) {
-				can_rx_unregister(net, dev, so->rxid,
-						  SINGLE_MASK(so->rxid),
-						  isotp_rcv, sk);
+				if (isotp_register_rxid(so))
+					can_rx_unregister(net, dev, so->rxid,
+							  SINGLE_MASK(so->rxid),
+							  isotp_rcv, sk);
+
+				can_rx_unregister(net, dev, so->txid,
+						  SINGLE_MASK(so->txid),
+						  isotp_rcv_echo, sk);
 				dev_put(dev);
 				synchronize_rcu();
 			}
 		}
 	}
 
+	hrtimer_cancel(&so->txfrtimer);
 	hrtimer_cancel(&so->txtimer);
 	hrtimer_cancel(&so->rxtimer);
 
@@ -1090,42 +1213,54 @@
 	struct net *net = sock_net(sk);
 	int ifindex;
 	struct net_device *dev;
+	canid_t tx_id = addr->can_addr.tp.tx_id;
+	canid_t rx_id = addr->can_addr.tp.rx_id;
 	int err = 0;
 	int notify_enetdown = 0;
-	int do_rx_reg = 1;
 
 	if (len < ISOTP_MIN_NAMELEN)
 		return -EINVAL;
 
-	if (addr->can_addr.tp.tx_id & (CAN_ERR_FLAG | CAN_RTR_FLAG))
-		return -EADDRNOTAVAIL;
+	if (addr->can_family != AF_CAN)
+		return -EINVAL;
+
+	/* sanitize tx CAN identifier */
+	if (tx_id & CAN_EFF_FLAG)
+		tx_id &= (CAN_EFF_FLAG | CAN_EFF_MASK);
+	else
+		tx_id &= CAN_SFF_MASK;
+
+	/* give feedback on wrong CAN-ID value */
+	if (tx_id != addr->can_addr.tp.tx_id)
+		return -EINVAL;
+
+	/* sanitize rx CAN identifier (if needed) */
+	if (isotp_register_rxid(so)) {
+		if (rx_id & CAN_EFF_FLAG)
+			rx_id &= (CAN_EFF_FLAG | CAN_EFF_MASK);
+		else
+			rx_id &= CAN_SFF_MASK;
+
+		/* give feedback on wrong CAN-ID value */
+		if (rx_id != addr->can_addr.tp.rx_id)
+			return -EINVAL;
+	}
 
 	if (!addr->can_ifindex)
 		return -ENODEV;
 
 	lock_sock(sk);
 
-	/* do not register frame reception for functional addressing */
-	if (so->opt.flags & CAN_ISOTP_SF_BROADCAST)
-		do_rx_reg = 0;
-
-	/* do not validate rx address for functional addressing */
-	if (do_rx_reg) {
-		if (addr->can_addr.tp.rx_id == addr->can_addr.tp.tx_id) {
-			err = -EADDRNOTAVAIL;
-			goto out;
-		}
-
-		if (addr->can_addr.tp.rx_id & (CAN_ERR_FLAG | CAN_RTR_FLAG)) {
-			err = -EADDRNOTAVAIL;
-			goto out;
-		}
+	if (so->bound) {
+		err = -EINVAL;
+		goto out;
 	}
 
-	if (so->bound && addr->can_ifindex == so->ifindex &&
-	    addr->can_addr.tp.rx_id == so->rxid &&
-	    addr->can_addr.tp.tx_id == so->txid)
+	/* ensure different CAN IDs when the rx_id is to be registered */
+	if (isotp_register_rxid(so) && rx_id == tx_id) {
+		err = -EADDRNOTAVAIL;
 		goto out;
+	}
 
 	dev = dev_get_by_index(net, addr->can_ifindex);
 	if (!dev) {
@@ -1147,30 +1282,23 @@
 
 	ifindex = dev->ifindex;
 
-	if (do_rx_reg)
-		can_rx_register(net, dev, addr->can_addr.tp.rx_id,
-				SINGLE_MASK(addr->can_addr.tp.rx_id),
+	if (isotp_register_rxid(so))
+		can_rx_register(net, dev, rx_id, SINGLE_MASK(rx_id),
 				isotp_rcv, sk, "isotp", sk);
 
-	dev_put(dev);
+	/* no consecutive frame echo skb in flight */
+	so->cfecho = 0;
 
-	if (so->bound && do_rx_reg) {
-		/* unregister old filter */
-		if (so->ifindex) {
-			dev = dev_get_by_index(net, so->ifindex);
-			if (dev) {
-				can_rx_unregister(net, dev, so->rxid,
-						  SINGLE_MASK(so->rxid),
-						  isotp_rcv, sk);
-				dev_put(dev);
-			}
-		}
-	}
+	/* register for echo skb's */
+	can_rx_register(net, dev, tx_id, SINGLE_MASK(tx_id),
+			isotp_rcv_echo, sk, "isotpe", sk);
+
+	dev_put(dev);
 
 	/* switch to new settings */
 	so->ifindex = ifindex;
-	so->rxid = addr->can_addr.tp.rx_id;
-	so->txid = addr->can_addr.tp.tx_id;
+	so->rxid = rx_id;
+	so->txid = tx_id;
 	so->bound = 1;
 
 out:
@@ -1224,6 +1352,23 @@
 		/* no separate rx_ext_address is given => use ext_address */
 		if (!(so->opt.flags & CAN_ISOTP_RX_EXT_ADDR))
 			so->opt.rx_ext_address = so->opt.ext_address;
+
+		/* these broadcast flags are not allowed together */
+		if (isotp_bc_flags(so) == ISOTP_ALL_BC_FLAGS) {
+			/* CAN_ISOTP_SF_BROADCAST is prioritized */
+			so->opt.flags &= ~CAN_ISOTP_CF_BROADCAST;
+
+			/* give user feedback on wrong config attempt */
+			ret = -EINVAL;
+		}
+
+		/* check for frame_txtime changes (0 => no changes) */
+		if (so->opt.frame_txtime) {
+			if (so->opt.frame_txtime == CAN_ISOTP_FRAME_TXTIME_ZERO)
+				so->frame_txtime = 0;
+			else
+				so->frame_txtime = so->opt.frame_txtime;
+		}
 		break;
 
 	case CAN_ISOTP_RECV_FC:
@@ -1367,10 +1512,16 @@
 	case NETDEV_UNREGISTER:
 		lock_sock(sk);
 		/* remove current filters & unregister */
-		if (so->bound && (!(so->opt.flags & CAN_ISOTP_SF_BROADCAST)))
-			can_rx_unregister(dev_net(dev), dev, so->rxid,
-					  SINGLE_MASK(so->rxid),
-					  isotp_rcv, sk);
+		if (so->bound) {
+			if (isotp_register_rxid(so))
+				can_rx_unregister(dev_net(dev), dev, so->rxid,
+						  SINGLE_MASK(so->rxid),
+						  isotp_rcv, sk);
+
+			can_rx_unregister(dev_net(dev), dev, so->txid,
+					  SINGLE_MASK(so->txid),
+					  isotp_rcv_echo, sk);
+		}
 
 		so->ifindex = 0;
 		so->bound  = 0;
@@ -1425,6 +1576,7 @@
 	so->opt.rxpad_content = CAN_ISOTP_DEFAULT_PAD_CONTENT;
 	so->opt.txpad_content = CAN_ISOTP_DEFAULT_PAD_CONTENT;
 	so->opt.frame_txtime = CAN_ISOTP_DEFAULT_FRAME_TXTIME;
+	so->frame_txtime = CAN_ISOTP_DEFAULT_FRAME_TXTIME;
 	so->rxfc.bs = CAN_ISOTP_DEFAULT_RECV_BS;
 	so->rxfc.stmin = CAN_ISOTP_DEFAULT_RECV_STMIN;
 	so->rxfc.wftmax = CAN_ISOTP_DEFAULT_RECV_WFTMAX;
@@ -1442,8 +1594,11 @@
 	so->rxtimer.function = isotp_rx_timer_handler;
 	hrtimer_init(&so->txtimer, CLOCK_MONOTONIC, HRTIMER_MODE_REL_SOFT);
 	so->txtimer.function = isotp_tx_timer_handler;
+	hrtimer_init(&so->txfrtimer, CLOCK_MONOTONIC, HRTIMER_MODE_REL_SOFT);
+	so->txfrtimer.function = isotp_txfr_timer_handler;
 
 	init_waitqueue_head(&so->wait);
+	spin_lock_init(&so->rx_lock);
 
 	spin_lock(&isotp_notifier_lock);
 	list_add_tail(&so->notifier, &isotp_notifier_list);
@@ -1452,6 +1607,21 @@
 	return 0;
 }
 
+static __poll_t isotp_poll(struct file *file, struct socket *sock, poll_table *wait)
+{
+	struct sock *sk = sock->sk;
+	struct isotp_sock *so = isotp_sk(sk);
+
+	__poll_t mask = datagram_poll(file, sock, wait);
+	poll_wait(file, &so->wait, wait);
+
+	/* Check for false positives due to TX state */
+	if ((mask & EPOLLWRNORM) && (so->tx.state != ISOTP_IDLE))
+		mask &= ~(EPOLLOUT | EPOLLWRNORM);
+
+	return mask;
+}
+
 static int isotp_sock_no_ioctlcmd(struct socket *sock, unsigned int cmd,
 				  unsigned long arg)
 {
@@ -1467,7 +1637,7 @@
 	.socketpair = sock_no_socketpair,
 	.accept = sock_no_accept,
 	.getname = isotp_getname,
-	.poll = datagram_poll,
+	.poll = isotp_poll,
 	.ioctl = isotp_sock_no_ioctlcmd,
 	.gettstamp = sock_gettstamp,
 	.listen = sock_no_listen,
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/j1939/address-claim.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/j1939/address-claim.c
@@ -165,6 +165,46 @@
 	 * leaving this function.
 	 */
 	ecu = j1939_ecu_get_by_name_locked(priv, name);
+
+	if (ecu && ecu->addr == skcb->addr.sa) {
+		/* The ISO 11783-5 standard, in "4.5.2 - Address claim
+		 * requirements", states:
+		 *   d) No CF shall begin, or resume, transmission on the
+		 *      network until 250 ms after it has successfully claimed
+		 *      an address except when responding to a request for
+		 *      address-claimed.
+		 *
+		 * But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
+		 * prioritization" show that the CF begins the transmission
+		 * after 250 ms from the first AC (address-claimed) message
+		 * even if it sends another AC message during that time window
+		 * to resolve the address contention with another CF.
+		 *
+		 * As stated in "4.4.2.3 - Address-claimed message":
+		 *   In order to successfully claim an address, the CF sending
+		 *   an address claimed message shall not receive a contending
+		 *   claim from another CF for at least 250 ms.
+		 *
+		 * As stated in "4.4.3.2 - NAME management (NM) message":
+		 *   1) A commanding CF can
+		 *      d) request that a CF with a specified NAME transmit
+		 *         the address-claimed message with its current NAME.
+		 *   2) A target CF shall
+		 *      d) send an address-claimed message in response to a
+		 *         request for a matching NAME
+		 *
+		 * Taking the above arguments into account, the 250 ms wait is
+		 * requested only during network initialization.
+		 *
+		 * Do not restart the timer on AC message if both the NAME and
+		 * the address match and so if the address has already been
+		 * claimed (timer has expired) or the AC message has been sent
+		 * to resolve the contention with another CF (timer is still
+		 * running).
+		 */
+		goto out_ecu_put;
+	}
+
 	if (!ecu && j1939_address_is_unicast(skcb->addr.sa))
 		ecu = j1939_ecu_create_locked(priv, name);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/j1939/j1939-priv.h
+++ linux-xilinx-zynqmp-5.15.0/net/can/j1939/j1939-priv.h
@@ -86,7 +86,7 @@
 	unsigned int tp_max_packet_size;
 
 	/* lock for j1939_socks list */
-	spinlock_t j1939_socks_lock;
+	rwlock_t j1939_socks_lock;
 	struct list_head j1939_socks;
 
 	struct kref rx_kref;
@@ -301,6 +301,7 @@
 
 	int ifindex;
 	struct j1939_addr addr;
+	spinlock_t filters_lock;
 	struct j1939_filter *filters;
 	int nfilters;
 	pgn_t pgn_rx_filter;
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/j1939/main.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/j1939/main.c
@@ -30,10 +30,6 @@
 /* CAN_HDR: #bytes before can_frame data part */
 #define J1939_CAN_HDR (offsetof(struct can_frame, data))
 
-/* CAN_FTR: #bytes beyond data part */
-#define J1939_CAN_FTR (sizeof(struct can_frame) - J1939_CAN_HDR - \
-		 sizeof(((struct can_frame *)0)->data))
-
 /* lowest layer */
 static void j1939_can_recv(struct sk_buff *iskb, void *data)
 {
@@ -75,6 +71,13 @@
 	skcb->addr.pgn = (cf->can_id >> 8) & J1939_PGN_MAX;
 	/* set default message type */
 	skcb->addr.type = J1939_TP;
+
+	if (!j1939_address_is_valid(skcb->addr.sa)) {
+		netdev_err_once(priv->ndev, "%s: sa is broadcast address, ignoring!\n",
+				__func__);
+		goto done;
+	}
+
 	if (j1939_pgn_is_pdu1(skcb->addr.pgn)) {
 		/* Type 1: with destination address */
 		skcb->addr.da = skcb->addr.pgn;
@@ -115,7 +118,7 @@
 #define J1939_CAN_ID CAN_EFF_FLAG
 #define J1939_CAN_MASK (CAN_EFF_FLAG | CAN_RTR_FLAG)
 
-static DEFINE_SPINLOCK(j1939_netdev_lock);
+static DEFINE_MUTEX(j1939_netdev_lock);
 
 static struct j1939_priv *j1939_priv_create(struct net_device *ndev)
 {
@@ -209,7 +212,7 @@
 	j1939_can_rx_unregister(priv);
 	j1939_ecu_unmap_all(priv);
 	j1939_priv_set(priv->ndev, NULL);
-	spin_unlock(&j1939_netdev_lock);
+	mutex_unlock(&j1939_netdev_lock);
 }
 
 /* get pointer to priv without increasing ref counter */
@@ -237,9 +240,9 @@
 {
 	struct j1939_priv *priv;
 
-	spin_lock(&j1939_netdev_lock);
+	mutex_lock(&j1939_netdev_lock);
 	priv = j1939_priv_get_by_ndev_locked(ndev);
-	spin_unlock(&j1939_netdev_lock);
+	mutex_unlock(&j1939_netdev_lock);
 
 	return priv;
 }
@@ -249,46 +252,48 @@
 	struct j1939_priv *priv, *priv_new;
 	int ret;
 
-	spin_lock(&j1939_netdev_lock);
+	mutex_lock(&j1939_netdev_lock);
 	priv = j1939_priv_get_by_ndev_locked(ndev);
 	if (priv) {
 		kref_get(&priv->rx_kref);
-		spin_unlock(&j1939_netdev_lock);
+		mutex_unlock(&j1939_netdev_lock);
 		return priv;
 	}
-	spin_unlock(&j1939_netdev_lock);
+	mutex_unlock(&j1939_netdev_lock);
 
 	priv = j1939_priv_create(ndev);
 	if (!priv)
 		return ERR_PTR(-ENOMEM);
 
 	j1939_tp_init(priv);
-	spin_lock_init(&priv->j1939_socks_lock);
+	rwlock_init(&priv->j1939_socks_lock);
 	INIT_LIST_HEAD(&priv->j1939_socks);
 
-	spin_lock(&j1939_netdev_lock);
+	mutex_lock(&j1939_netdev_lock);
 	priv_new = j1939_priv_get_by_ndev_locked(ndev);
 	if (priv_new) {
 		/* Someone was faster than us, use their priv and roll
 		 * back our's.
 		 */
 		kref_get(&priv_new->rx_kref);
-		spin_unlock(&j1939_netdev_lock);
+		mutex_unlock(&j1939_netdev_lock);
 		dev_put(ndev);
 		kfree(priv);
 		return priv_new;
 	}
 	j1939_priv_set(ndev, priv);
-	spin_unlock(&j1939_netdev_lock);
 
 	ret = j1939_can_rx_register(priv);
 	if (ret < 0)
 		goto out_priv_put;
 
+	mutex_unlock(&j1939_netdev_lock);
 	return priv;
 
  out_priv_put:
 	j1939_priv_set(ndev, NULL);
+	mutex_unlock(&j1939_netdev_lock);
+
 	dev_put(ndev);
 	kfree(priv);
 
@@ -297,7 +302,7 @@
 
 void j1939_netdev_stop(struct j1939_priv *priv)
 {
-	kref_put_lock(&priv->rx_kref, __j1939_rx_release, &j1939_netdev_lock);
+	kref_put_mutex(&priv->rx_kref, __j1939_rx_release, &j1939_netdev_lock);
 	j1939_priv_put(priv);
 }
 
@@ -325,8 +330,11 @@
 	/* re-claim the CAN_HDR from the SKB */
 	cf = skb_push(skb, J1939_CAN_HDR);
 
+	/* initialize header structure */
+	memset(cf, 0, J1939_CAN_HDR);
+
 	/* make it a full can frame again */
-	skb_put(skb, J1939_CAN_FTR + (8 - dlc));
+	skb_put_zero(skb, 8 - dlc);
 
 	canid = CAN_EFF_FLAG |
 		(skcb->priority << 26) |
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/j1939/socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/j1939/socket.c
@@ -80,16 +80,16 @@
 	jsk->state |= J1939_SOCK_BOUND;
 	j1939_priv_get(priv);
 
-	spin_lock_bh(&priv->j1939_socks_lock);
+	write_lock_bh(&priv->j1939_socks_lock);
 	list_add_tail(&jsk->list, &priv->j1939_socks);
-	spin_unlock_bh(&priv->j1939_socks_lock);
+	write_unlock_bh(&priv->j1939_socks_lock);
 }
 
 static void j1939_jsk_del(struct j1939_priv *priv, struct j1939_sock *jsk)
 {
-	spin_lock_bh(&priv->j1939_socks_lock);
+	write_lock_bh(&priv->j1939_socks_lock);
 	list_del_init(&jsk->list);
-	spin_unlock_bh(&priv->j1939_socks_lock);
+	write_unlock_bh(&priv->j1939_socks_lock);
 
 	j1939_priv_put(priv);
 	jsk->state &= ~J1939_SOCK_BOUND;
@@ -178,7 +178,10 @@
 	if (!first)
 		return;
 
-	if (WARN_ON_ONCE(j1939_session_activate(first))) {
+	if (j1939_session_activate(first)) {
+		netdev_warn_once(first->priv->ndev,
+				 "%s: 0x%p: Identical session is already activated.\n",
+				 __func__, first);
 		first->err = -EBUSY;
 		goto activate_next;
 	} else {
@@ -259,12 +262,17 @@
 static bool j1939_sk_match_filter(struct j1939_sock *jsk,
 				  const struct j1939_sk_buff_cb *skcb)
 {
-	const struct j1939_filter *f = jsk->filters;
-	int nfilter = jsk->nfilters;
+	const struct j1939_filter *f;
+	int nfilter;
+
+	spin_lock_bh(&jsk->filters_lock);
+
+	f = jsk->filters;
+	nfilter = jsk->nfilters;
 
 	if (!nfilter)
 		/* receive all when no filters are assigned */
-		return true;
+		goto filter_match_found;
 
 	for (; nfilter; ++f, --nfilter) {
 		if ((skcb->addr.pgn & f->pgn_mask) != f->pgn)
@@ -273,9 +281,15 @@
 			continue;
 		if ((skcb->addr.src_name & f->name_mask) != f->name)
 			continue;
-		return true;
+		goto filter_match_found;
 	}
+
+	spin_unlock_bh(&jsk->filters_lock);
 	return false;
+
+filter_match_found:
+	spin_unlock_bh(&jsk->filters_lock);
+	return true;
 }
 
 static bool j1939_sk_recv_match_one(struct j1939_sock *jsk,
@@ -326,13 +340,13 @@
 	struct j1939_sock *jsk;
 	bool match = false;
 
-	spin_lock_bh(&priv->j1939_socks_lock);
+	read_lock_bh(&priv->j1939_socks_lock);
 	list_for_each_entry(jsk, &priv->j1939_socks, list) {
 		match = j1939_sk_recv_match_one(jsk, skcb);
 		if (match)
 			break;
 	}
-	spin_unlock_bh(&priv->j1939_socks_lock);
+	read_unlock_bh(&priv->j1939_socks_lock);
 
 	return match;
 }
@@ -341,11 +355,11 @@
 {
 	struct j1939_sock *jsk;
 
-	spin_lock_bh(&priv->j1939_socks_lock);
+	read_lock_bh(&priv->j1939_socks_lock);
 	list_for_each_entry(jsk, &priv->j1939_socks, list) {
 		j1939_sk_recv_one(jsk, skb);
 	}
-	spin_unlock_bh(&priv->j1939_socks_lock);
+	read_unlock_bh(&priv->j1939_socks_lock);
 }
 
 static void j1939_sk_sock_destruct(struct sock *sk)
@@ -398,6 +412,7 @@
 	atomic_set(&jsk->skb_pending, 0);
 	spin_lock_init(&jsk->sk_session_queue_lock);
 	INIT_LIST_HEAD(&jsk->sk_session_queue);
+	spin_lock_init(&jsk->filters_lock);
 
 	/* j1939_sk_sock_destruct() depends on SOCK_RCU_FREE flag */
 	sock_set_flag(sk, SOCK_RCU_FREE);
@@ -700,9 +715,11 @@
 		}
 
 		lock_sock(&jsk->sk);
+		spin_lock_bh(&jsk->filters_lock);
 		ofilters = jsk->filters;
 		jsk->filters = filters;
 		jsk->nfilters = count;
+		spin_unlock_bh(&jsk->filters_lock);
 		release_sock(&jsk->sk);
 		kfree(ofilters);
 		return 0;
@@ -795,7 +812,7 @@
 	struct j1939_sk_buff_cb *skcb;
 	int ret = 0;
 
-	if (flags & ~(MSG_DONTWAIT | MSG_ERRQUEUE))
+	if (flags & ~(MSG_DONTWAIT | MSG_ERRQUEUE | MSG_CMSG_COMPAT))
 		return -EINVAL;
 
 	if (flags & MSG_ERRQUEUE)
@@ -1075,16 +1092,21 @@
 	}
 
 	/* spread RX notifications to all sockets subscribed to this session */
-	spin_lock_bh(&priv->j1939_socks_lock);
+	read_lock_bh(&priv->j1939_socks_lock);
 	list_for_each_entry(jsk, &priv->j1939_socks, list) {
 		if (j1939_sk_recv_match_one(jsk, &session->skcb))
 			__j1939_sk_errqueue(session, &jsk->sk, type);
 	}
-	spin_unlock_bh(&priv->j1939_socks_lock);
+	read_unlock_bh(&priv->j1939_socks_lock);
 };
 
 void j1939_sk_send_loop_abort(struct sock *sk, int err)
 {
+	struct j1939_sock *jsk = j1939_sk(sk);
+
+	if (jsk->state & J1939_SOCK_ERRQUEUE)
+		return;
+
 	sk->sk_err = err;
 
 	sk_error_report(sk);
@@ -1108,7 +1130,7 @@
 
 	todo_size = size;
 
-	while (todo_size) {
+	do {
 		struct j1939_sk_buff_cb *skcb;
 
 		segment_size = min_t(size_t, J1939_MAX_TP_PACKET_SIZE,
@@ -1153,7 +1175,7 @@
 
 		todo_size -= segment_size;
 		session->total_queued_size += segment_size;
-	}
+	} while (todo_size);
 
 	switch (ret) {
 	case 0: /* OK */
@@ -1263,7 +1285,7 @@
 	struct j1939_sock *jsk;
 	int error_code = ENETDOWN;
 
-	spin_lock_bh(&priv->j1939_socks_lock);
+	read_lock_bh(&priv->j1939_socks_lock);
 	list_for_each_entry(jsk, &priv->j1939_socks, list) {
 		jsk->sk.sk_err = error_code;
 		if (!sock_flag(&jsk->sk, SOCK_DEAD))
@@ -1271,7 +1293,7 @@
 
 		j1939_sk_queue_drop_all(priv, jsk, error_code);
 	}
-	spin_unlock_bh(&priv->j1939_socks_lock);
+	read_unlock_bh(&priv->j1939_socks_lock);
 }
 
 static int j1939_sk_no_ioctlcmd(struct socket *sock, unsigned int cmd,
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/j1939/transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/j1939/transport.c
@@ -260,6 +260,8 @@
 
 static void j1939_session_destroy(struct j1939_session *session)
 {
+	struct sk_buff *skb;
+
 	if (session->transmission) {
 		if (session->err)
 			j1939_sk_errqueue(session, J1939_ERRQUEUE_TX_ABORT);
@@ -274,7 +276,11 @@
 	WARN_ON_ONCE(!list_empty(&session->sk_session_queue_entry));
 	WARN_ON_ONCE(!list_empty(&session->active_session_list_entry));
 
-	skb_queue_purge(&session->skb_queue);
+	while ((skb = skb_dequeue(&session->skb_queue)) != NULL) {
+		/* drop ref taken in j1939_session_skb_queue() */
+		skb_unref(skb);
+		kfree_skb(skb);
+	}
 	__j1939_session_drop(session);
 	j1939_priv_put(session->priv);
 	kfree(session);
@@ -336,10 +342,12 @@
 		__skb_unlink(do_skb, &session->skb_queue);
 		/* drop ref taken in j1939_session_skb_queue() */
 		skb_unref(do_skb);
+		spin_unlock_irqrestore(&session->skb_queue.lock, flags);
 
 		kfree_skb(do_skb);
+	} else {
+		spin_unlock_irqrestore(&session->skb_queue.lock, flags);
 	}
-	spin_unlock_irqrestore(&session->skb_queue.lock, flags);
 }
 
 void j1939_session_skb_queue(struct j1939_session *session,
@@ -374,8 +382,9 @@
 	skb_queue_walk(&session->skb_queue, do_skb) {
 		do_skcb = j1939_skb_to_cb(do_skb);
 
-		if (offset_start >= do_skcb->offset &&
-		    offset_start < (do_skcb->offset + do_skb->len)) {
+		if ((offset_start >= do_skcb->offset &&
+		     offset_start < (do_skcb->offset + do_skb->len)) ||
+		     (offset_start == 0 && do_skcb->offset == 0 && do_skb->len == 0)) {
 			skb = do_skb;
 		}
 	}
@@ -596,7 +605,10 @@
 	/* reserve CAN header */
 	skb_reserve(skb, offsetof(struct can_frame, data));
 
-	memcpy(skb->cb, re_skcb, sizeof(skb->cb));
+	/* skb->cb must be large enough to hold a j1939_sk_buff_cb structure */
+	BUILD_BUG_ON(sizeof(skb->cb) < sizeof(*re_skcb));
+
+	memcpy(skb->cb, re_skcb, sizeof(*re_skcb));
 	skcb = j1939_skb_to_cb(skb);
 	if (swap_src_dst)
 		j1939_skbcb_swap(skcb);
@@ -1084,10 +1096,6 @@
 	bool active;
 
 	j1939_session_list_lock(priv);
-	/* This function should be called with a session ref-count of at
-	 * least 2.
-	 */
-	WARN_ON_ONCE(kref_read(&session->kref) < 2);
 	active = j1939_session_deactivate_locked(session);
 	j1939_session_list_unlock(priv);
 
@@ -1120,8 +1128,6 @@
 
 	if (session->sk)
 		j1939_sk_send_loop_abort(session->sk, session->err);
-	else
-		j1939_sk_errqueue(session, J1939_ERRQUEUE_RX_ABORT);
 }
 
 static void j1939_session_cancel(struct j1939_session *session,
@@ -1136,6 +1142,9 @@
 	}
 
 	j1939_session_list_unlock(session->priv);
+
+	if (!session->sk)
+		j1939_sk_errqueue(session, J1939_ERRQUEUE_RX_ABORT);
 }
 
 static enum hrtimer_restart j1939_tp_txtimer(struct hrtimer *hrtimer)
@@ -1171,10 +1180,10 @@
 		break;
 	case -ENETDOWN:
 		/* In this case we should get a netdev_event(), all active
-		 * sessions will be cleared by
-		 * j1939_cancel_all_active_sessions(). So handle this as an
-		 * error, but let j1939_cancel_all_active_sessions() do the
-		 * cleanup including propagation of the error to user space.
+		 * sessions will be cleared by j1939_cancel_active_session().
+		 * So handle this as an error, but let
+		 * j1939_cancel_active_session() do the cleanup including
+		 * propagation of the error to user space.
 		 */
 		break;
 	case -EOVERFLOW:
@@ -1249,6 +1258,9 @@
 			__j1939_session_cancel(session, J1939_XTP_ABORT_TIMEOUT);
 		}
 		j1939_session_list_unlock(session->priv);
+
+		if (!session->sk)
+			j1939_sk_errqueue(session, J1939_ERRQUEUE_RX_ABORT);
 	}
 
 	j1939_session_put(session);
@@ -1494,7 +1506,7 @@
 	session->state = J1939_SESSION_NEW;
 
 	skb_queue_head_init(&session->skb_queue);
-	skb_queue_tail(&session->skb_queue, skb);
+	skb_queue_tail(&session->skb_queue, skb_get(skb));
 
 	skcb = j1939_skb_to_cb(skb);
 	memcpy(&session->skcb, skcb, sizeof(session->skcb));
@@ -1582,8 +1594,8 @@
 	struct j1939_sk_buff_cb skcb = *j1939_skb_to_cb(skb);
 	struct j1939_session *session;
 	const u8 *dat;
+	int len, ret;
 	pgn_t pgn;
-	int len;
 
 	netdev_dbg(priv->ndev, "%s\n", __func__);
 
@@ -1642,7 +1654,22 @@
 	session->tskey = priv->rx_tskey++;
 	j1939_sk_errqueue(session, J1939_ERRQUEUE_RX_RTS);
 
-	WARN_ON_ONCE(j1939_session_activate(session));
+	ret = j1939_session_activate(session);
+	if (ret) {
+		/* Entering this scope indicates an issue with the J1939 bus.
+		 * Possible scenarios include:
+		 * - A time lapse occurred, and a new session was initiated
+		 *   due to another packet being sent correctly. This could
+		 *   have been caused by too long interrupt, debugger, or being
+		 *   out-scheduled by another task.
+		 * - The bus is receiving numerous erroneous packets, either
+		 *   from a malfunctioning device or during a test scenario.
+		 */
+		netdev_alert(priv->ndev, "%s: 0x%p: concurrent session with same addr (%02x %02x) is already active.\n",
+			     __func__, session, skcb.addr.sa, skcb.addr.da);
+		j1939_session_put(session);
+		return NULL;
+	}
 
 	return session;
 }
@@ -1670,6 +1697,8 @@
 
 		j1939_session_timers_cancel(session);
 		j1939_session_cancel(session, J1939_XTP_ABORT_BUSY);
+		if (session->transmission)
+			j1939_session_deactivate_activate_next(session);
 
 		return -EBUSY;
 	}
@@ -2006,7 +2035,7 @@
 		/* set the end-packet for broadcast */
 		session->pkt.last = session->pkt.total;
 
-	skcb->tskey = session->sk->sk_tskey++;
+	skcb->tskey = atomic_inc_return(&session->sk->sk_tskey) - 1;
 	session->tskey = skcb->tskey;
 
 	return session;
@@ -2023,6 +2052,11 @@
 		extd = J1939_ETP;
 		fallthrough;
 	case J1939_TP_CMD_BAM:
+		if (cmd == J1939_TP_CMD_BAM && !j1939_cb_is_broadcast(skcb)) {
+			netdev_err_once(priv->ndev, "%s: BAM to unicast (%02x), ignoring!\n",
+					__func__, skcb->addr.sa);
+			return;
+		}
 		fallthrough;
 	case J1939_TP_CMD_RTS:
 		if (skcb->addr.type != extd)
@@ -2085,6 +2119,12 @@
 		break;
 
 	case J1939_ETP_CMD_ABORT: /* && J1939_TP_CMD_ABORT */
+		if (j1939_cb_is_broadcast(skcb)) {
+			netdev_err_once(priv->ndev, "%s: abort to broadcast (%02x), ignoring!\n",
+					__func__, skcb->addr.sa);
+			return;
+		}
+
 		if (j1939_tp_im_transmitter(skcb))
 			j1939_xtp_rx_abort(priv, skb, true);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/proc.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/proc.c
@@ -118,6 +118,13 @@
 	struct can_pkg_stats *pkg_stats = net->can.pkg_stats;
 	unsigned long j = jiffies; /* snapshot */
 
+	long rx_frames = atomic_long_read(&pkg_stats->rx_frames);
+	long tx_frames = atomic_long_read(&pkg_stats->tx_frames);
+	long matches = atomic_long_read(&pkg_stats->matches);
+	long rx_frames_delta = atomic_long_read(&pkg_stats->rx_frames_delta);
+	long tx_frames_delta = atomic_long_read(&pkg_stats->tx_frames_delta);
+	long matches_delta = atomic_long_read(&pkg_stats->matches_delta);
+
 	/* restart counting in timer context on user request */
 	if (user_reset)
 		can_init_stats(net);
@@ -127,35 +134,33 @@
 		can_init_stats(net);
 
 	/* prevent overflow in calc_rate() */
-	if (pkg_stats->rx_frames > (ULONG_MAX / HZ))
+	if (rx_frames > (LONG_MAX / HZ))
 		can_init_stats(net);
 
 	/* prevent overflow in calc_rate() */
-	if (pkg_stats->tx_frames > (ULONG_MAX / HZ))
+	if (tx_frames > (LONG_MAX / HZ))
 		can_init_stats(net);
 
 	/* matches overflow - very improbable */
-	if (pkg_stats->matches > (ULONG_MAX / 100))
+	if (matches > (LONG_MAX / 100))
 		can_init_stats(net);
 
 	/* calc total values */
-	if (pkg_stats->rx_frames)
-		pkg_stats->total_rx_match_ratio = (pkg_stats->matches * 100) /
-			pkg_stats->rx_frames;
+	if (rx_frames)
+		pkg_stats->total_rx_match_ratio = (matches * 100) / rx_frames;
 
 	pkg_stats->total_tx_rate = calc_rate(pkg_stats->jiffies_init, j,
-					    pkg_stats->tx_frames);
+					    tx_frames);
 	pkg_stats->total_rx_rate = calc_rate(pkg_stats->jiffies_init, j,
-					    pkg_stats->rx_frames);
+					    rx_frames);
 
 	/* calc current values */
-	if (pkg_stats->rx_frames_delta)
+	if (rx_frames_delta)
 		pkg_stats->current_rx_match_ratio =
-			(pkg_stats->matches_delta * 100) /
-			pkg_stats->rx_frames_delta;
+			(matches_delta * 100) /	rx_frames_delta;
 
-	pkg_stats->current_tx_rate = calc_rate(0, HZ, pkg_stats->tx_frames_delta);
-	pkg_stats->current_rx_rate = calc_rate(0, HZ, pkg_stats->rx_frames_delta);
+	pkg_stats->current_tx_rate = calc_rate(0, HZ, tx_frames_delta);
+	pkg_stats->current_rx_rate = calc_rate(0, HZ, rx_frames_delta);
 
 	/* check / update maximum values */
 	if (pkg_stats->max_tx_rate < pkg_stats->current_tx_rate)
@@ -168,9 +173,9 @@
 		pkg_stats->max_rx_match_ratio = pkg_stats->current_rx_match_ratio;
 
 	/* clear values for 'current rate' calculation */
-	pkg_stats->tx_frames_delta = 0;
-	pkg_stats->rx_frames_delta = 0;
-	pkg_stats->matches_delta   = 0;
+	atomic_long_set(&pkg_stats->tx_frames_delta, 0);
+	atomic_long_set(&pkg_stats->rx_frames_delta, 0);
+	atomic_long_set(&pkg_stats->matches_delta, 0);
 
 	/* restart timer (one second) */
 	mod_timer(&net->can.stattimer, round_jiffies(jiffies + HZ));
@@ -214,9 +219,12 @@
 	struct can_rcv_lists_stats *rcv_lists_stats = net->can.rcv_lists_stats;
 
 	seq_putc(m, '\n');
-	seq_printf(m, " %8ld transmitted frames (TXF)\n", pkg_stats->tx_frames);
-	seq_printf(m, " %8ld received frames (RXF)\n", pkg_stats->rx_frames);
-	seq_printf(m, " %8ld matched frames (RXMF)\n", pkg_stats->matches);
+	seq_printf(m, " %8ld transmitted frames (TXF)\n",
+		   atomic_long_read(&pkg_stats->tx_frames));
+	seq_printf(m, " %8ld received frames (RXF)\n",
+		   atomic_long_read(&pkg_stats->rx_frames));
+	seq_printf(m, " %8ld matched frames (RXMF)\n",
+		   atomic_long_read(&pkg_stats->matches));
 
 	seq_putc(m, '\n');
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/can/raw.c
+++ linux-xilinx-zynqmp-5.15.0/net/can/raw.c
@@ -83,6 +83,7 @@
 	struct sock sk;
 	int bound;
 	int ifindex;
+	struct net_device *dev;
 	struct list_head notifier;
 	int loopback;
 	int recv_own_msgs;
@@ -275,21 +276,24 @@
 	if (!net_eq(dev_net(dev), sock_net(sk)))
 		return;
 
-	if (ro->ifindex != dev->ifindex)
+	if (ro->dev != dev)
 		return;
 
 	switch (msg) {
 	case NETDEV_UNREGISTER:
 		lock_sock(sk);
 		/* remove current filters & unregister */
-		if (ro->bound)
+		if (ro->bound) {
 			raw_disable_allfilters(dev_net(dev), dev, sk);
+			dev_put(dev);
+		}
 
 		if (ro->count > 1)
 			kfree(ro->filter);
 
 		ro->ifindex = 0;
 		ro->bound = 0;
+		ro->dev = NULL;
 		ro->count = 0;
 		release_sock(sk);
 
@@ -335,6 +339,7 @@
 
 	ro->bound            = 0;
 	ro->ifindex          = 0;
+	ro->dev              = NULL;
 
 	/* set default filter to single entry dfilter */
 	ro->dfilter.can_id   = 0;
@@ -380,18 +385,14 @@
 	list_del(&ro->notifier);
 	spin_unlock(&raw_notifier_lock);
 
+	rtnl_lock();
 	lock_sock(sk);
 
 	/* remove current filters & unregister */
 	if (ro->bound) {
-		if (ro->ifindex) {
-			struct net_device *dev;
-
-			dev = dev_get_by_index(sock_net(sk), ro->ifindex);
-			if (dev) {
-				raw_disable_allfilters(dev_net(dev), dev, sk);
-				dev_put(dev);
-			}
+		if (ro->dev) {
+			raw_disable_allfilters(dev_net(ro->dev), ro->dev, sk);
+			dev_put(ro->dev);
 		} else {
 			raw_disable_allfilters(sock_net(sk), NULL, sk);
 		}
@@ -402,6 +403,7 @@
 
 	ro->ifindex = 0;
 	ro->bound = 0;
+	ro->dev = NULL;
 	ro->count = 0;
 	free_percpu(ro->uniq);
 
@@ -409,6 +411,8 @@
 	sock->sk = NULL;
 
 	release_sock(sk);
+	rtnl_unlock();
+
 	sock_put(sk);
 
 	return 0;
@@ -419,6 +423,7 @@
 	struct sockaddr_can *addr = (struct sockaddr_can *)uaddr;
 	struct sock *sk = sock->sk;
 	struct raw_sock *ro = raw_sk(sk);
+	struct net_device *dev = NULL;
 	int ifindex;
 	int err = 0;
 	int notify_enetdown = 0;
@@ -428,24 +433,23 @@
 	if (addr->can_family != AF_CAN)
 		return -EINVAL;
 
+	rtnl_lock();
 	lock_sock(sk);
 
 	if (ro->bound && addr->can_ifindex == ro->ifindex)
 		goto out;
 
 	if (addr->can_ifindex) {
-		struct net_device *dev;
-
 		dev = dev_get_by_index(sock_net(sk), addr->can_ifindex);
 		if (!dev) {
 			err = -ENODEV;
 			goto out;
 		}
 		if (dev->type != ARPHRD_CAN) {
-			dev_put(dev);
 			err = -ENODEV;
-			goto out;
+			goto out_put_dev;
 		}
+
 		if (!(dev->flags & IFF_UP))
 			notify_enetdown = 1;
 
@@ -453,7 +457,9 @@
 
 		/* filters set by default/setsockopt */
 		err = raw_enable_allfilters(sock_net(sk), dev, sk);
-		dev_put(dev);
+		if (err)
+			goto out_put_dev;
+
 	} else {
 		ifindex = 0;
 
@@ -464,26 +470,30 @@
 	if (!err) {
 		if (ro->bound) {
 			/* unregister old filters */
-			if (ro->ifindex) {
-				struct net_device *dev;
-
-				dev = dev_get_by_index(sock_net(sk),
-						       ro->ifindex);
-				if (dev) {
-					raw_disable_allfilters(dev_net(dev),
-							       dev, sk);
-					dev_put(dev);
-				}
+			if (ro->dev) {
+				raw_disable_allfilters(dev_net(ro->dev),
+						       ro->dev, sk);
+				/* drop reference to old ro->dev */
+				dev_put(ro->dev);
 			} else {
 				raw_disable_allfilters(sock_net(sk), NULL, sk);
 			}
 		}
 		ro->ifindex = ifindex;
 		ro->bound = 1;
+		/* bind() ok -> hold a reference for new ro->dev */
+		ro->dev = dev;
+		if (ro->dev)
+			dev_hold(ro->dev);
 	}
 
- out:
+out_put_dev:
+	/* remove potential reference from dev_get_by_index() */
+	if (dev)
+		dev_put(dev);
+out:
 	release_sock(sk);
+	rtnl_unlock();
 
 	if (notify_enetdown) {
 		sk->sk_err = ENETDOWN;
@@ -549,9 +559,9 @@
 		rtnl_lock();
 		lock_sock(sk);
 
-		if (ro->bound && ro->ifindex) {
-			dev = dev_get_by_index(sock_net(sk), ro->ifindex);
-			if (!dev) {
+		dev = ro->dev;
+		if (ro->bound && dev) {
+			if (dev->reg_state != NETREG_REGISTERED) {
 				if (count > 1)
 					kfree(filter);
 				err = -ENODEV;
@@ -592,7 +602,6 @@
 		ro->count  = count;
 
  out_fil:
-		dev_put(dev);
 		release_sock(sk);
 		rtnl_unlock();
 
@@ -610,9 +619,9 @@
 		rtnl_lock();
 		lock_sock(sk);
 
-		if (ro->bound && ro->ifindex) {
-			dev = dev_get_by_index(sock_net(sk), ro->ifindex);
-			if (!dev) {
+		dev = ro->dev;
+		if (ro->bound && dev) {
+			if (dev->reg_state != NETREG_REGISTERED) {
 				err = -ENODEV;
 				goto out_err;
 			}
@@ -636,7 +645,6 @@
 		ro->err_mask = err_mask;
 
  out_err:
-		dev_put(dev);
 		release_sock(sk);
 		rtnl_unlock();
 
@@ -772,6 +780,7 @@
 {
 	struct sock *sk = sock->sk;
 	struct raw_sock *ro = raw_sk(sk);
+	struct sockcm_cookie sockc;
 	struct sk_buff *skb;
 	struct net_device *dev;
 	int ifindex;
@@ -817,11 +826,20 @@
 	if (err < 0)
 		goto free_skb;
 
-	skb_setup_tx_timestamp(skb, sk->sk_tsflags);
+	sockcm_init(&sockc, sk);
+	if (msg->msg_controllen) {
+		err = sock_cmsg_send(sk, msg, &sockc);
+		if (unlikely(err))
+			goto free_skb;
+	}
 
 	skb->dev = dev;
 	skb->sk = sk;
 	skb->priority = sk->sk_priority;
+	skb->mark = sk->sk_mark;
+	skb->tstamp = sockc.transmit_time;
+
+	skb_setup_tx_timestamp(skb, sockc.tsflags);
 
 	err = can_send(skb, ro->loopback);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ceph/messenger.c
+++ linux-xilinx-zynqmp-5.15.0/net/ceph/messenger.c
@@ -454,8 +454,8 @@
 	set_sock_callbacks(sock, con);
 
 	con_sock_state_connecting(con);
-	ret = sock->ops->connect(sock, (struct sockaddr *)&ss, sizeof(ss),
-				 O_NONBLOCK);
+	ret = kernel_connect(sock, (struct sockaddr *)&ss, sizeof(ss),
+			     O_NONBLOCK);
 	if (ret == -EINPROGRESS) {
 		dout("connect %s EINPROGRESS sk_state = %u\n",
 		     ceph_pr_addr(&con->peer_addr),
@@ -1144,6 +1144,7 @@
 		return true;
 	}
 }
+EXPORT_SYMBOL(ceph_addr_is_blank);
 
 int ceph_addr_port(const struct ceph_entity_addr *addr)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ceph/messenger_v2.c
+++ linux-xilinx-zynqmp-5.15.0/net/ceph/messenger_v2.c
@@ -391,6 +391,8 @@
 	int head_len;
 	int rem_len;
 
+	BUG_ON(ctrl_len < 0 || ctrl_len > CEPH_MSG_MAX_CONTROL_LEN);
+
 	if (secure) {
 		head_len = CEPH_PREAMBLE_SECURE_LEN;
 		if (ctrl_len > CEPH_PREAMBLE_INLINE_LEN) {
@@ -409,6 +411,10 @@
 static int __tail_onwire_len(int front_len, int middle_len, int data_len,
 			     bool secure)
 {
+	BUG_ON(front_len < 0 || front_len > CEPH_MSG_MAX_FRONT_LEN ||
+	       middle_len < 0 || middle_len > CEPH_MSG_MAX_MIDDLE_LEN ||
+	       data_len < 0 || data_len > CEPH_MSG_MAX_DATA_LEN);
+
 	if (!front_len && !middle_len && !data_len)
 		return 0;
 
@@ -521,29 +527,34 @@
 		desc->fd_aligns[i] = ceph_decode_16(&p);
 	}
 
-	/*
-	 * This would fire for FRAME_TAG_WAIT (it has one empty
-	 * segment), but we should never get it as client.
-	 */
-	if (!desc->fd_lens[desc->fd_seg_cnt - 1]) {
-		pr_err("last segment empty\n");
+	if (desc->fd_lens[0] < 0 ||
+	    desc->fd_lens[0] > CEPH_MSG_MAX_CONTROL_LEN) {
+		pr_err("bad control segment length %d\n", desc->fd_lens[0]);
 		return -EINVAL;
 	}
-
-	if (desc->fd_lens[0] > CEPH_MSG_MAX_CONTROL_LEN) {
-		pr_err("control segment too big %d\n", desc->fd_lens[0]);
+	if (desc->fd_lens[1] < 0 ||
+	    desc->fd_lens[1] > CEPH_MSG_MAX_FRONT_LEN) {
+		pr_err("bad front segment length %d\n", desc->fd_lens[1]);
 		return -EINVAL;
 	}
-	if (desc->fd_lens[1] > CEPH_MSG_MAX_FRONT_LEN) {
-		pr_err("front segment too big %d\n", desc->fd_lens[1]);
+	if (desc->fd_lens[2] < 0 ||
+	    desc->fd_lens[2] > CEPH_MSG_MAX_MIDDLE_LEN) {
+		pr_err("bad middle segment length %d\n", desc->fd_lens[2]);
 		return -EINVAL;
 	}
-	if (desc->fd_lens[2] > CEPH_MSG_MAX_MIDDLE_LEN) {
-		pr_err("middle segment too big %d\n", desc->fd_lens[2]);
+	if (desc->fd_lens[3] < 0 ||
+	    desc->fd_lens[3] > CEPH_MSG_MAX_DATA_LEN) {
+		pr_err("bad data segment length %d\n", desc->fd_lens[3]);
 		return -EINVAL;
 	}
-	if (desc->fd_lens[3] > CEPH_MSG_MAX_DATA_LEN) {
-		pr_err("data segment too big %d\n", desc->fd_lens[3]);
+
+	/*
+	 * This would fire for FRAME_TAG_WAIT (it has one empty
+	 * segment), but we should never get it as client.
+	 */
+	if (!desc->fd_lens[desc->fd_seg_cnt - 1]) {
+		pr_err("last segment empty, segment count %d\n",
+		       desc->fd_seg_cnt);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ceph/mon_client.c
+++ linux-xilinx-zynqmp-5.15.0/net/ceph/mon_client.c
@@ -1085,13 +1085,19 @@
 	struct ceph_mon_client *monc =
 		container_of(work, struct ceph_mon_client, delayed_work.work);
 
-	dout("monc delayed_work\n");
 	mutex_lock(&monc->mutex);
+	dout("%s mon%d\n", __func__, monc->cur_mon);
+	if (monc->cur_mon < 0) {
+		goto out;
+	}
+
 	if (monc->hunting) {
 		dout("%s continuing hunt\n", __func__);
 		reopen_session(monc);
 	} else {
 		int is_auth = ceph_auth_is_authenticated(monc->auth);
+
+		dout("%s is_authed %d\n", __func__, is_auth);
 		if (ceph_con_keepalive_expired(&monc->con,
 					       CEPH_MONC_PING_TIMEOUT)) {
 			dout("monc keepalive timeout\n");
@@ -1116,6 +1122,8 @@
 		}
 	}
 	__schedule_delayed(monc);
+
+out:
 	mutex_unlock(&monc->mutex);
 }
 
@@ -1233,13 +1241,15 @@
 void ceph_monc_stop(struct ceph_mon_client *monc)
 {
 	dout("stop\n");
-	cancel_delayed_work_sync(&monc->delayed_work);
 
 	mutex_lock(&monc->mutex);
 	__close_session(monc);
+	monc->hunting = false;
 	monc->cur_mon = -1;
 	mutex_unlock(&monc->mutex);
 
+	cancel_delayed_work_sync(&monc->delayed_work);
+
 	/*
 	 * flush msgr queue before we destroy ourselves to ensure that:
 	 *  - any work that references our embedded con is finished.
--- linux-xilinx-zynqmp-5.15.0.orig/net/ceph/osd_client.c
+++ linux-xilinx-zynqmp-5.15.0/net/ceph/osd_client.c
@@ -537,43 +537,6 @@
 	target_init(&req->r_t);
 }
 
-/*
- * This is ugly, but it allows us to reuse linger registration and ping
- * requests, keeping the structure of the code around send_linger{_ping}()
- * reasonable.  Setting up a min_nr=2 mempool for each linger request
- * and dealing with copying ops (this blasts req only, watch op remains
- * intact) isn't any better.
- */
-static void request_reinit(struct ceph_osd_request *req)
-{
-	struct ceph_osd_client *osdc = req->r_osdc;
-	bool mempool = req->r_mempool;
-	unsigned int num_ops = req->r_num_ops;
-	u64 snapid = req->r_snapid;
-	struct ceph_snap_context *snapc = req->r_snapc;
-	bool linger = req->r_linger;
-	struct ceph_msg *request_msg = req->r_request;
-	struct ceph_msg *reply_msg = req->r_reply;
-
-	dout("%s req %p\n", __func__, req);
-	WARN_ON(kref_read(&req->r_kref) != 1);
-	request_release_checks(req);
-
-	WARN_ON(kref_read(&request_msg->kref) != 1);
-	WARN_ON(kref_read(&reply_msg->kref) != 1);
-	target_destroy(&req->r_t);
-
-	request_init(req);
-	req->r_osdc = osdc;
-	req->r_mempool = mempool;
-	req->r_num_ops = num_ops;
-	req->r_snapid = snapid;
-	req->r_snapc = snapc;
-	req->r_linger = linger;
-	req->r_request = request_msg;
-	req->r_reply = reply_msg;
-}
-
 struct ceph_osd_request *ceph_osdc_alloc_request(struct ceph_osd_client *osdc,
 					       struct ceph_snap_context *snapc,
 					       unsigned int num_ops,
@@ -918,14 +881,30 @@
  * @watch_opcode: CEPH_OSD_WATCH_OP_*
  */
 static void osd_req_op_watch_init(struct ceph_osd_request *req, int which,
-				  u64 cookie, u8 watch_opcode)
+				  u8 watch_opcode, u64 cookie, u32 gen)
 {
 	struct ceph_osd_req_op *op;
 
 	op = osd_req_op_init(req, which, CEPH_OSD_OP_WATCH, 0);
 	op->watch.cookie = cookie;
 	op->watch.op = watch_opcode;
-	op->watch.gen = 0;
+	op->watch.gen = gen;
+}
+
+/*
+ * prot_ver, timeout and notify payload (may be empty) should already be
+ * encoded in @request_pl
+ */
+static void osd_req_op_notify_init(struct ceph_osd_request *req, int which,
+				   u64 cookie, struct ceph_pagelist *request_pl)
+{
+	struct ceph_osd_req_op *op;
+
+	op = osd_req_op_init(req, which, CEPH_OSD_OP_NOTIFY, 0);
+	op->notify.cookie = cookie;
+
+	ceph_osd_data_pagelist_init(&op->notify.request_data, request_pl);
+	op->indata_len = request_pl->length;
 }
 
 /*
@@ -2727,10 +2706,13 @@
 	WARN_ON(!list_empty(&lreq->pending_lworks));
 	WARN_ON(lreq->osd);
 
-	if (lreq->reg_req)
-		ceph_osdc_put_request(lreq->reg_req);
-	if (lreq->ping_req)
-		ceph_osdc_put_request(lreq->ping_req);
+	if (lreq->request_pl)
+		ceph_pagelist_release(lreq->request_pl);
+	if (lreq->notify_id_pages)
+		ceph_release_page_vector(lreq->notify_id_pages, 1);
+
+	ceph_osdc_put_request(lreq->reg_req);
+	ceph_osdc_put_request(lreq->ping_req);
 	target_destroy(&lreq->t);
 	kfree(lreq);
 }
@@ -2999,6 +2981,12 @@
 	struct ceph_osd_linger_request *lreq = req->r_priv;
 
 	mutex_lock(&lreq->lock);
+	if (req != lreq->reg_req) {
+		dout("%s lreq %p linger_id %llu unknown req (%p != %p)\n",
+		     __func__, lreq, lreq->linger_id, req, lreq->reg_req);
+		goto out;
+	}
+
 	dout("%s lreq %p linger_id %llu result %d\n", __func__, lreq,
 	     lreq->linger_id, req->r_result);
 	linger_reg_commit_complete(lreq, req->r_result);
@@ -3022,6 +3010,7 @@
 		}
 	}
 
+out:
 	mutex_unlock(&lreq->lock);
 	linger_put(lreq);
 }
@@ -3044,6 +3033,12 @@
 	struct ceph_osd_linger_request *lreq = req->r_priv;
 
 	mutex_lock(&lreq->lock);
+	if (req != lreq->reg_req) {
+		dout("%s lreq %p linger_id %llu unknown req (%p != %p)\n",
+		     __func__, lreq, lreq->linger_id, req, lreq->reg_req);
+		goto out;
+	}
+
 	dout("%s lreq %p linger_id %llu result %d last_error %d\n", __func__,
 	     lreq, lreq->linger_id, req->r_result, lreq->last_error);
 	if (req->r_result < 0) {
@@ -3053,46 +3048,64 @@
 		}
 	}
 
+out:
 	mutex_unlock(&lreq->lock);
 	linger_put(lreq);
 }
 
 static void send_linger(struct ceph_osd_linger_request *lreq)
 {
-	struct ceph_osd_request *req = lreq->reg_req;
-	struct ceph_osd_req_op *op = &req->r_ops[0];
+	struct ceph_osd_client *osdc = lreq->osdc;
+	struct ceph_osd_request *req;
+	int ret;
 
-	verify_osdc_wrlocked(req->r_osdc);
+	verify_osdc_wrlocked(osdc);
+	mutex_lock(&lreq->lock);
 	dout("%s lreq %p linger_id %llu\n", __func__, lreq, lreq->linger_id);
 
-	if (req->r_osd)
-		cancel_linger_request(req);
+	if (lreq->reg_req) {
+		if (lreq->reg_req->r_osd)
+			cancel_linger_request(lreq->reg_req);
+		ceph_osdc_put_request(lreq->reg_req);
+	}
+
+	req = ceph_osdc_alloc_request(osdc, NULL, 1, true, GFP_NOIO);
+	BUG_ON(!req);
 
-	request_reinit(req);
 	target_copy(&req->r_t, &lreq->t);
 	req->r_mtime = lreq->mtime;
 
-	mutex_lock(&lreq->lock);
 	if (lreq->is_watch && lreq->committed) {
-		WARN_ON(op->op != CEPH_OSD_OP_WATCH ||
-			op->watch.cookie != lreq->linger_id);
-		op->watch.op = CEPH_OSD_WATCH_OP_RECONNECT;
-		op->watch.gen = ++lreq->register_gen;
+		osd_req_op_watch_init(req, 0, CEPH_OSD_WATCH_OP_RECONNECT,
+				      lreq->linger_id, ++lreq->register_gen);
 		dout("lreq %p reconnect register_gen %u\n", lreq,
-		     op->watch.gen);
+		     req->r_ops[0].watch.gen);
 		req->r_callback = linger_reconnect_cb;
 	} else {
-		if (!lreq->is_watch)
+		if (lreq->is_watch) {
+			osd_req_op_watch_init(req, 0, CEPH_OSD_WATCH_OP_WATCH,
+					      lreq->linger_id, 0);
+		} else {
 			lreq->notify_id = 0;
-		else
-			WARN_ON(op->watch.op != CEPH_OSD_WATCH_OP_WATCH);
+
+			refcount_inc(&lreq->request_pl->refcnt);
+			osd_req_op_notify_init(req, 0, lreq->linger_id,
+					       lreq->request_pl);
+			ceph_osd_data_pages_init(
+			    osd_req_op_data(req, 0, notify, response_data),
+			    lreq->notify_id_pages, PAGE_SIZE, 0, false, false);
+		}
 		dout("lreq %p register\n", lreq);
 		req->r_callback = linger_commit_cb;
 	}
-	mutex_unlock(&lreq->lock);
+
+	ret = ceph_osdc_alloc_messages(req, GFP_NOIO);
+	BUG_ON(ret);
 
 	req->r_priv = linger_get(lreq);
 	req->r_linger = true;
+	lreq->reg_req = req;
+	mutex_unlock(&lreq->lock);
 
 	submit_request(req, true);
 }
@@ -3102,6 +3115,12 @@
 	struct ceph_osd_linger_request *lreq = req->r_priv;
 
 	mutex_lock(&lreq->lock);
+	if (req != lreq->ping_req) {
+		dout("%s lreq %p linger_id %llu unknown req (%p != %p)\n",
+		     __func__, lreq, lreq->linger_id, req, lreq->ping_req);
+		goto out;
+	}
+
 	dout("%s lreq %p linger_id %llu result %d ping_sent %lu last_error %d\n",
 	     __func__, lreq, lreq->linger_id, req->r_result, lreq->ping_sent,
 	     lreq->last_error);
@@ -3117,6 +3136,7 @@
 		     lreq->register_gen, req->r_ops[0].watch.gen);
 	}
 
+out:
 	mutex_unlock(&lreq->lock);
 	linger_put(lreq);
 }
@@ -3124,8 +3144,8 @@
 static void send_linger_ping(struct ceph_osd_linger_request *lreq)
 {
 	struct ceph_osd_client *osdc = lreq->osdc;
-	struct ceph_osd_request *req = lreq->ping_req;
-	struct ceph_osd_req_op *op = &req->r_ops[0];
+	struct ceph_osd_request *req;
+	int ret;
 
 	if (ceph_osdmap_flag(osdc, CEPH_OSDMAP_PAUSERD)) {
 		dout("%s PAUSERD\n", __func__);
@@ -3137,19 +3157,26 @@
 	     __func__, lreq, lreq->linger_id, lreq->ping_sent,
 	     lreq->register_gen);
 
-	if (req->r_osd)
-		cancel_linger_request(req);
+	if (lreq->ping_req) {
+		if (lreq->ping_req->r_osd)
+			cancel_linger_request(lreq->ping_req);
+		ceph_osdc_put_request(lreq->ping_req);
+	}
 
-	request_reinit(req);
-	target_copy(&req->r_t, &lreq->t);
+	req = ceph_osdc_alloc_request(osdc, NULL, 1, true, GFP_NOIO);
+	BUG_ON(!req);
 
-	WARN_ON(op->op != CEPH_OSD_OP_WATCH ||
-		op->watch.cookie != lreq->linger_id ||
-		op->watch.op != CEPH_OSD_WATCH_OP_PING);
-	op->watch.gen = lreq->register_gen;
+	target_copy(&req->r_t, &lreq->t);
+	osd_req_op_watch_init(req, 0, CEPH_OSD_WATCH_OP_PING, lreq->linger_id,
+			      lreq->register_gen);
 	req->r_callback = linger_ping_cb;
+
+	ret = ceph_osdc_alloc_messages(req, GFP_NOIO);
+	BUG_ON(ret);
+
 	req->r_priv = linger_get(lreq);
 	req->r_linger = true;
+	lreq->ping_req = req;
 
 	ceph_osdc_get_request(req);
 	account_request(req);
@@ -3165,12 +3192,6 @@
 
 	down_write(&osdc->lock);
 	linger_register(lreq);
-	if (lreq->is_watch) {
-		lreq->reg_req->r_ops[0].watch.cookie = lreq->linger_id;
-		lreq->ping_req->r_ops[0].watch.cookie = lreq->linger_id;
-	} else {
-		lreq->reg_req->r_ops[0].notify.cookie = lreq->linger_id;
-	}
 
 	calc_target(osdc, &lreq->t, false);
 	osd = lookup_create_osd(osdc, lreq->t.osd, true);
@@ -3202,9 +3223,9 @@
  */
 static void __linger_cancel(struct ceph_osd_linger_request *lreq)
 {
-	if (lreq->is_watch && lreq->ping_req->r_osd)
+	if (lreq->ping_req && lreq->ping_req->r_osd)
 		cancel_linger_request(lreq->ping_req);
-	if (lreq->reg_req->r_osd)
+	if (lreq->reg_req && lreq->reg_req->r_osd)
 		cancel_linger_request(lreq->reg_req);
 	cancel_linger_map_check(lreq);
 	unlink_linger(lreq->osd, lreq);
@@ -3309,17 +3330,24 @@
 	int ret;
 
 	dout("%s lreq %p linger_id %llu\n", __func__, lreq, lreq->linger_id);
-	ret = wait_for_completion_interruptible(&lreq->reg_commit_wait);
+	ret = wait_for_completion_killable(&lreq->reg_commit_wait);
 	return ret ?: lreq->reg_commit_error;
 }
 
-static int linger_notify_finish_wait(struct ceph_osd_linger_request *lreq)
+static int linger_notify_finish_wait(struct ceph_osd_linger_request *lreq,
+				     unsigned long timeout)
 {
-	int ret;
+	long left;
 
 	dout("%s lreq %p linger_id %llu\n", __func__, lreq, lreq->linger_id);
-	ret = wait_for_completion_interruptible(&lreq->notify_finish_wait);
-	return ret ?: lreq->notify_finish_error;
+	left = wait_for_completion_killable_timeout(&lreq->notify_finish_wait,
+						ceph_timeout_jiffies(timeout));
+	if (left <= 0)
+		left = left ?: -ETIMEDOUT;
+	else
+		left = lreq->notify_finish_error; /* completed */
+
+	return left;
 }
 
 /*
@@ -4653,43 +4681,6 @@
 }
 EXPORT_SYMBOL(ceph_osdc_sync);
 
-static struct ceph_osd_request *
-alloc_linger_request(struct ceph_osd_linger_request *lreq)
-{
-	struct ceph_osd_request *req;
-
-	req = ceph_osdc_alloc_request(lreq->osdc, NULL, 1, false, GFP_NOIO);
-	if (!req)
-		return NULL;
-
-	ceph_oid_copy(&req->r_base_oid, &lreq->t.base_oid);
-	ceph_oloc_copy(&req->r_base_oloc, &lreq->t.base_oloc);
-	return req;
-}
-
-static struct ceph_osd_request *
-alloc_watch_request(struct ceph_osd_linger_request *lreq, u8 watch_opcode)
-{
-	struct ceph_osd_request *req;
-
-	req = alloc_linger_request(lreq);
-	if (!req)
-		return NULL;
-
-	/*
-	 * Pass 0 for cookie because we don't know it yet, it will be
-	 * filled in by linger_submit().
-	 */
-	osd_req_op_watch_init(req, 0, 0, watch_opcode);
-
-	if (ceph_osdc_alloc_messages(req, GFP_NOIO)) {
-		ceph_osdc_put_request(req);
-		return NULL;
-	}
-
-	return req;
-}
-
 /*
  * Returns a handle, caller owns a ref.
  */
@@ -4719,18 +4710,6 @@
 	lreq->t.flags = CEPH_OSD_FLAG_WRITE;
 	ktime_get_real_ts64(&lreq->mtime);
 
-	lreq->reg_req = alloc_watch_request(lreq, CEPH_OSD_WATCH_OP_WATCH);
-	if (!lreq->reg_req) {
-		ret = -ENOMEM;
-		goto err_put_lreq;
-	}
-
-	lreq->ping_req = alloc_watch_request(lreq, CEPH_OSD_WATCH_OP_PING);
-	if (!lreq->ping_req) {
-		ret = -ENOMEM;
-		goto err_put_lreq;
-	}
-
 	linger_submit(lreq);
 	ret = linger_reg_commit_wait(lreq);
 	if (ret) {
@@ -4768,8 +4747,8 @@
 	ceph_oloc_copy(&req->r_base_oloc, &lreq->t.base_oloc);
 	req->r_flags = CEPH_OSD_FLAG_WRITE;
 	ktime_get_real_ts64(&req->r_mtime);
-	osd_req_op_watch_init(req, 0, lreq->linger_id,
-			      CEPH_OSD_WATCH_OP_UNWATCH);
+	osd_req_op_watch_init(req, 0, CEPH_OSD_WATCH_OP_UNWATCH,
+			      lreq->linger_id, 0);
 
 	ret = ceph_osdc_alloc_messages(req, GFP_NOIO);
 	if (ret)
@@ -4855,35 +4834,6 @@
 }
 EXPORT_SYMBOL(ceph_osdc_notify_ack);
 
-static int osd_req_op_notify_init(struct ceph_osd_request *req, int which,
-				  u64 cookie, u32 prot_ver, u32 timeout,
-				  void *payload, u32 payload_len)
-{
-	struct ceph_osd_req_op *op;
-	struct ceph_pagelist *pl;
-	int ret;
-
-	op = osd_req_op_init(req, which, CEPH_OSD_OP_NOTIFY, 0);
-	op->notify.cookie = cookie;
-
-	pl = ceph_pagelist_alloc(GFP_NOIO);
-	if (!pl)
-		return -ENOMEM;
-
-	ret = ceph_pagelist_encode_32(pl, 1); /* prot_ver */
-	ret |= ceph_pagelist_encode_32(pl, timeout);
-	ret |= ceph_pagelist_encode_32(pl, payload_len);
-	ret |= ceph_pagelist_append(pl, payload, payload_len);
-	if (ret) {
-		ceph_pagelist_release(pl);
-		return -ENOMEM;
-	}
-
-	ceph_osd_data_pagelist_init(&op->notify.request_data, pl);
-	op->indata_len = pl->length;
-	return 0;
-}
-
 /*
  * @timeout: in seconds
  *
@@ -4902,7 +4852,6 @@
 		     size_t *preply_len)
 {
 	struct ceph_osd_linger_request *lreq;
-	struct page **pages;
 	int ret;
 
 	WARN_ON(!timeout);
@@ -4915,46 +4864,41 @@
 	if (!lreq)
 		return -ENOMEM;
 
-	lreq->preply_pages = preply_pages;
-	lreq->preply_len = preply_len;
-
-	ceph_oid_copy(&lreq->t.base_oid, oid);
-	ceph_oloc_copy(&lreq->t.base_oloc, oloc);
-	lreq->t.flags = CEPH_OSD_FLAG_READ;
-
-	lreq->reg_req = alloc_linger_request(lreq);
-	if (!lreq->reg_req) {
+	lreq->request_pl = ceph_pagelist_alloc(GFP_NOIO);
+	if (!lreq->request_pl) {
 		ret = -ENOMEM;
 		goto out_put_lreq;
 	}
 
-	/*
-	 * Pass 0 for cookie because we don't know it yet, it will be
-	 * filled in by linger_submit().
-	 */
-	ret = osd_req_op_notify_init(lreq->reg_req, 0, 0, 1, timeout,
-				     payload, payload_len);
-	if (ret)
+	ret = ceph_pagelist_encode_32(lreq->request_pl, 1); /* prot_ver */
+	ret |= ceph_pagelist_encode_32(lreq->request_pl, timeout);
+	ret |= ceph_pagelist_encode_32(lreq->request_pl, payload_len);
+	ret |= ceph_pagelist_append(lreq->request_pl, payload, payload_len);
+	if (ret) {
+		ret = -ENOMEM;
 		goto out_put_lreq;
+	}
 
 	/* for notify_id */
-	pages = ceph_alloc_page_vector(1, GFP_NOIO);
-	if (IS_ERR(pages)) {
-		ret = PTR_ERR(pages);
+	lreq->notify_id_pages = ceph_alloc_page_vector(1, GFP_NOIO);
+	if (IS_ERR(lreq->notify_id_pages)) {
+		ret = PTR_ERR(lreq->notify_id_pages);
+		lreq->notify_id_pages = NULL;
 		goto out_put_lreq;
 	}
-	ceph_osd_data_pages_init(osd_req_op_data(lreq->reg_req, 0, notify,
-						 response_data),
-				 pages, PAGE_SIZE, 0, false, true);
 
-	ret = ceph_osdc_alloc_messages(lreq->reg_req, GFP_NOIO);
-	if (ret)
-		goto out_put_lreq;
+	lreq->preply_pages = preply_pages;
+	lreq->preply_len = preply_len;
+
+	ceph_oid_copy(&lreq->t.base_oid, oid);
+	ceph_oloc_copy(&lreq->t.base_oloc, oloc);
+	lreq->t.flags = CEPH_OSD_FLAG_READ;
 
 	linger_submit(lreq);
 	ret = linger_reg_commit_wait(lreq);
 	if (!ret)
-		ret = linger_notify_finish_wait(lreq);
+		ret = linger_notify_finish_wait(lreq,
+				 msecs_to_jiffies(2 * timeout * MSEC_PER_SEC));
 	else
 		dout("lreq %p failed to initiate notify %d\n", lreq, ret);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/core/Makefile
@@ -36,3 +36,4 @@
 obj-$(CONFIG_NET_SOCK_MSG) += skmsg.o
 obj-$(CONFIG_BPF_SYSCALL) += sock_map.o
 obj-$(CONFIG_BPF_SYSCALL) += bpf_sk_storage.o
+obj-$(CONFIG_OF)	+= of_net.o
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/bpf_sk_storage.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/bpf_sk_storage.c
@@ -305,11 +305,12 @@
 static int bpf_sk_storage_charge(struct bpf_local_storage_map *smap,
 				 void *owner, u32 size)
 {
+	int optmem_max = READ_ONCE(sysctl_optmem_max);
 	struct sock *sk = (struct sock *)owner;
 
 	/* same check as in sock_kmalloc() */
-	if (size <= sysctl_optmem_max &&
-	    atomic_read(&sk->sk_omem_alloc) + size < sysctl_optmem_max) {
+	if (size <= optmem_max &&
+	    atomic_read(&sk->sk_omem_alloc) + size < optmem_max) {
 		atomic_add(size, &sk->sk_omem_alloc);
 		return 0;
 	}
@@ -520,8 +521,11 @@
 		return ERR_PTR(-EPERM);
 
 	nla_for_each_nested(nla, nla_stgs, rem) {
-		if (nla_type(nla) == SK_DIAG_BPF_STORAGE_REQ_MAP_FD)
+		if (nla_type(nla) == SK_DIAG_BPF_STORAGE_REQ_MAP_FD) {
+			if (nla_len(nla) != sizeof(u32))
+				return ERR_PTR(-EINVAL);
 			nr_maps++;
+		}
 	}
 
 	diag = kzalloc(struct_size(diag, maps, nr_maps), GFP_KERNEL);
@@ -865,10 +869,18 @@
 {
 	struct bpf_iter_seq_sk_storage_map_info *seq_info = priv_data;
 
+	bpf_map_inc_with_uref(aux->map);
 	seq_info->map = aux->map;
 	return 0;
 }
 
+static void bpf_iter_fini_sk_storage_map(void *priv_data)
+{
+	struct bpf_iter_seq_sk_storage_map_info *seq_info = priv_data;
+
+	bpf_map_put_with_uref(seq_info->map);
+}
+
 static int bpf_iter_attach_map(struct bpf_prog *prog,
 			       union bpf_iter_link_info *linfo,
 			       struct bpf_iter_aux_info *aux)
@@ -886,7 +898,7 @@
 	if (map->map_type != BPF_MAP_TYPE_SK_STORAGE)
 		goto put_map;
 
-	if (prog->aux->max_rdonly_access > map->value_size) {
+	if (prog->aux->max_rdwr_access > map->value_size) {
 		err = -EACCES;
 		goto put_map;
 	}
@@ -914,7 +926,7 @@
 static const struct bpf_iter_seq_info iter_seq_info = {
 	.seq_ops		= &bpf_sk_storage_map_seq_ops,
 	.init_seq_private	= bpf_iter_init_sk_storage_map,
-	.fini_seq_private	= NULL,
+	.fini_seq_private	= bpf_iter_fini_sk_storage_map,
 	.seq_priv_size		= sizeof(struct bpf_iter_seq_sk_storage_map_info),
 };
 
@@ -929,7 +941,7 @@
 		{ offsetof(struct bpf_iter__bpf_sk_storage_map, sk),
 		  PTR_TO_BTF_ID_OR_NULL },
 		{ offsetof(struct bpf_iter__bpf_sk_storage_map, value),
-		  PTR_TO_RDWR_BUF_OR_NULL },
+		  PTR_TO_BUF | PTR_MAYBE_NULL },
 	},
 	.seq_info		= &iter_seq_info,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/datagram.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/datagram.c
@@ -440,15 +440,23 @@
 
 		end = start + skb_frag_size(frag);
 		if ((copy = end - offset) > 0) {
-			struct page *page = skb_frag_page(frag);
-			u8 *vaddr = kmap(page);
+			u32 p_off, p_len, copied;
+			struct page *p;
+			u8 *vaddr;
 
 			if (copy > len)
 				copy = len;
-			n = INDIRECT_CALL_1(cb, simple_copy_to_iter,
-					vaddr + skb_frag_off(frag) + offset - start,
-					copy, data, to);
-			kunmap(page);
+
+			n = 0;
+			skb_frag_foreach_page(frag,
+					      skb_frag_off(frag) + offset - start,
+					      copy, p, p_off, p_len, copied) {
+				vaddr = kmap_local_page(p);
+				n += INDIRECT_CALL_1(cb, simple_copy_to_iter,
+					vaddr + p_off, p_len, data, to);
+				kunmap_local(vaddr);
+			}
+
 			offset += n;
 			if (n != copy)
 				goto short_copy;
@@ -677,7 +685,7 @@
 				page_ref_sub(last_head, refs);
 				refs = 0;
 			}
-			skb_fill_page_desc(skb, frag++, head, start, size);
+			skb_fill_page_desc_noacc(skb, frag++, head, start, size);
 		}
 		if (refs)
 			page_ref_sub(last_head, refs);
@@ -799,18 +807,21 @@
 {
 	struct sock *sk = sock->sk;
 	__poll_t mask;
+	u8 shutdown;
 
 	sock_poll_wait(file, sock, wait);
 	mask = 0;
 
 	/* exceptional events? */
-	if (sk->sk_err || !skb_queue_empty_lockless(&sk->sk_error_queue))
+	if (READ_ONCE(sk->sk_err) ||
+	    !skb_queue_empty_lockless(&sk->sk_error_queue))
 		mask |= EPOLLERR |
 			(sock_flag(sk, SOCK_SELECT_ERR_QUEUE) ? EPOLLPRI : 0);
 
-	if (sk->sk_shutdown & RCV_SHUTDOWN)
+	shutdown = READ_ONCE(sk->sk_shutdown);
+	if (shutdown & RCV_SHUTDOWN)
 		mask |= EPOLLRDHUP | EPOLLIN | EPOLLRDNORM;
-	if (sk->sk_shutdown == SHUTDOWN_MASK)
+	if (shutdown == SHUTDOWN_MASK)
 		mask |= EPOLLHUP;
 
 	/* readable? */
@@ -819,10 +830,12 @@
 
 	/* Connection-based need to check for termination and startup */
 	if (connection_based(sk)) {
-		if (sk->sk_state == TCP_CLOSE)
+		int state = READ_ONCE(sk->sk_state);
+
+		if (state == TCP_CLOSE)
 			mask |= EPOLLHUP;
 		/* connection hasn't started yet? */
-		if (sk->sk_state == TCP_SYN_SENT)
+		if (state == TCP_SYN_SENT)
 			return mask;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/dev.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/dev.c
@@ -303,6 +303,12 @@
 	return NULL;
 }
 
+bool netdev_name_in_use(struct net *net, const char *name)
+{
+	return netdev_name_node_lookup(net, name);
+}
+EXPORT_SYMBOL(netdev_name_in_use);
+
 int netdev_name_node_alt_create(struct net_device *dev, const char *name)
 {
 	struct netdev_name_node *name_node;
@@ -365,12 +371,12 @@
 
 	ASSERT_RTNL();
 
-	write_lock_bh(&dev_base_lock);
+	write_lock(&dev_base_lock);
 	list_add_tail_rcu(&dev->dev_list, &net->dev_base_head);
 	netdev_name_node_add(net, dev->name_node);
 	hlist_add_head_rcu(&dev->index_hlist,
 			   dev_index_hash(net, dev->ifindex));
-	write_unlock_bh(&dev_base_lock);
+	write_unlock(&dev_base_lock);
 
 	dev_base_seq_inc(net);
 }
@@ -378,16 +384,18 @@
 /* Device list removal
  * caller must respect a RCU grace period before freeing/reusing dev
  */
-static void unlist_netdevice(struct net_device *dev)
+static void unlist_netdevice(struct net_device *dev, bool lock)
 {
 	ASSERT_RTNL();
 
 	/* Unlink dev from the device chain */
-	write_lock_bh(&dev_base_lock);
+	if (lock)
+		write_lock(&dev_base_lock);
 	list_del_rcu(&dev->dev_list);
 	netdev_name_node_del(dev->name_node);
 	hlist_del_rcu(&dev->index_hlist);
-	write_unlock_bh(&dev_base_lock);
+	if (lock)
+		write_unlock(&dev_base_lock);
 
 	dev_base_seq_inc(dev_net(dev));
 }
@@ -741,11 +749,11 @@
 	const struct net_device *last_dev;
 	struct net_device_path_ctx ctx = {
 		.dev	= dev,
-		.daddr	= daddr,
 	};
 	struct net_device_path *path;
 	int ret = 0;
 
+	memcpy(ctx.daddr, daddr, sizeof(ctx.daddr));
 	stack->num_paths = 0;
 	while (ctx.dev && ctx.dev->netdev_ops->ndo_fill_forward_path) {
 		last_dev = ctx.dev;
@@ -964,6 +972,12 @@
 	return ret;
 }
 
+static bool dev_addr_cmp(struct net_device *dev, unsigned short type,
+			 const char *ha)
+{
+	return dev->type == type && !memcmp(dev->dev_addr, ha, dev->addr_len);
+}
+
 /**
  *	dev_getbyhwaddr_rcu - find a device by its hardware address
  *	@net: the applicable net namespace
@@ -972,7 +986,7 @@
  *
  *	Search for an interface by MAC address. Returns NULL if the device
  *	is not found or a pointer to the device.
- *	The caller must hold RCU or RTNL.
+ *	The caller must hold RCU.
  *	The returned device has not had its ref count increased
  *	and the caller must therefore be careful about locking
  *
@@ -984,14 +998,39 @@
 	struct net_device *dev;
 
 	for_each_netdev_rcu(net, dev)
-		if (dev->type == type &&
-		    !memcmp(dev->dev_addr, ha, dev->addr_len))
+		if (dev_addr_cmp(dev, type, ha))
 			return dev;
 
 	return NULL;
 }
 EXPORT_SYMBOL(dev_getbyhwaddr_rcu);
 
+/**
+ * dev_getbyhwaddr() - find a device by its hardware address
+ * @net: the applicable net namespace
+ * @type: media type of device
+ * @ha: hardware address
+ *
+ * Similar to dev_getbyhwaddr_rcu(), but the owner needs to hold
+ * rtnl_lock.
+ *
+ * Context: rtnl_lock() must be held.
+ * Return: pointer to the net_device, or NULL if not found
+ */
+struct net_device *dev_getbyhwaddr(struct net *net, unsigned short type,
+				   const char *ha)
+{
+	struct net_device *dev;
+
+	ASSERT_RTNL();
+	for_each_netdev(net, dev)
+		if (dev_addr_cmp(dev, type, ha))
+			return dev;
+
+	return NULL;
+}
+EXPORT_SYMBOL(dev_getbyhwaddr);
+
 struct net_device *dev_getfirstbyhwtype(struct net *net, unsigned short type)
 {
 	struct net_device *dev, *ret = NULL;
@@ -1133,7 +1172,7 @@
 	}
 
 	snprintf(buf, IFNAMSIZ, name, i);
-	if (!__dev_get_by_name(net, buf))
+	if (!netdev_name_in_use(net, buf))
 		return i;
 
 	/* It is possible to run out of possible slots
@@ -1143,6 +1182,26 @@
 	return -ENFILE;
 }
 
+static int dev_prep_valid_name(struct net *net, struct net_device *dev,
+			       const char *want_name, char *out_name)
+{
+	int ret;
+
+	if (!dev_valid_name(want_name))
+		return -EINVAL;
+
+	if (strchr(want_name, '%')) {
+		ret = __dev_alloc_name(net, want_name, out_name);
+		return ret < 0 ? ret : 0;
+	} else if (netdev_name_in_use(net, want_name)) {
+		return -EEXIST;
+	} else if (out_name != want_name) {
+		strscpy(out_name, want_name, IFNAMSIZ);
+	}
+
+	return 0;
+}
+
 static int dev_alloc_name_ns(struct net *net,
 			     struct net_device *dev,
 			     const char *name)
@@ -1153,7 +1212,7 @@
 	BUG_ON(!net);
 	ret = __dev_alloc_name(net, name, buf);
 	if (ret >= 0)
-		strlcpy(dev->name, buf, IFNAMSIZ);
+		strscpy(dev->name, buf, IFNAMSIZ);
 	return ret;
 }
 
@@ -1180,19 +1239,13 @@
 static int dev_get_valid_name(struct net *net, struct net_device *dev,
 			      const char *name)
 {
-	BUG_ON(!net);
-
-	if (!dev_valid_name(name))
-		return -EINVAL;
-
-	if (strchr(name, '%'))
-		return dev_alloc_name_ns(net, dev, name);
-	else if (__dev_get_by_name(net, name))
-		return -EEXIST;
-	else if (dev->name != name)
-		strlcpy(dev->name, name, IFNAMSIZ);
+	char buf[IFNAMSIZ];
+	int ret;
 
-	return 0;
+	ret = dev_prep_valid_name(net, dev, name, buf);
+	if (ret >= 0)
+		strscpy(dev->name, buf, IFNAMSIZ);
+	return ret;
 }
 
 /**
@@ -1266,15 +1319,15 @@
 
 	netdev_adjacent_rename_links(dev, oldname);
 
-	write_lock_bh(&dev_base_lock);
+	write_lock(&dev_base_lock);
 	netdev_name_node_del(dev->name_node);
-	write_unlock_bh(&dev_base_lock);
+	write_unlock(&dev_base_lock);
 
 	synchronize_rcu();
 
-	write_lock_bh(&dev_base_lock);
+	write_lock(&dev_base_lock);
 	netdev_name_node_add(net, dev->name_node);
-	write_unlock_bh(&dev_base_lock);
+	write_unlock(&dev_base_lock);
 
 	ret = call_netdevice_notifiers(NETDEV_CHANGENAME, dev);
 	ret = notifier_to_errno(ret);
@@ -2269,7 +2322,7 @@
 	rcu_read_lock();
 again:
 	list_for_each_entry_rcu(ptype, ptype_list, list) {
-		if (ptype->ignore_outgoing)
+		if (READ_ONCE(ptype->ignore_outgoing))
 			continue;
 
 		/* Never send packets back to the socket
@@ -2572,6 +2625,8 @@
 	struct xps_map *map, *new_map;
 	unsigned int nr_ids;
 
+	WARN_ON_ONCE(index >= dev->num_tx_queues);
+
 	if (dev->num_tc) {
 		/* Do not allow XPS on subordinate device directly */
 		num_tc = dev->num_tc;
@@ -2921,6 +2976,8 @@
 		if (dev->num_tc)
 			netif_setup_tc(dev, txq);
 
+		dev_qdisc_change_real_num_tx(dev, txq);
+
 		dev->real_num_tx_queues = txq;
 
 		if (disabling) {
@@ -3109,8 +3166,10 @@
 {
 	if (in_hardirq() || irqs_disabled())
 		__dev_kfree_skb_irq(skb, reason);
+	else if (unlikely(reason == SKB_REASON_DROPPED))
+		kfree_skb(skb);
 	else
-		dev_kfree_skb(skb);
+		consume_skb(skb);
 }
 EXPORT_SYMBOL(__dev_kfree_skb_any);
 
@@ -3231,11 +3290,15 @@
 	}
 
 	offset = skb_checksum_start_offset(skb);
-	BUG_ON(offset >= skb_headlen(skb));
+	ret = -EINVAL;
+	if (WARN_ON_ONCE(offset >= skb_headlen(skb)))
+		goto out;
+
 	csum = skb_checksum(skb, offset, skb->len - offset, 0);
 
 	offset += skb->csum_offset;
-	BUG_ON(offset + sizeof(__sum16) > skb_headlen(skb));
+	if (WARN_ON_ONCE(offset + sizeof(__sum16) > skb_headlen(skb)))
+		goto out;
 
 	ret = skb_ensure_writable(skb, offset + sizeof(__sum16));
 	if (ret)
@@ -3304,7 +3367,7 @@
 		type = eth->h_proto;
 	}
 
-	return __vlan_get_protocol(skb, type, depth);
+	return vlan_get_protocol_and_depth(skb, type, depth);
 }
 
 /**
@@ -3508,6 +3571,9 @@
 	if (gso_segs > dev->gso_max_segs)
 		return features & ~NETIF_F_GSO_MASK;
 
+	if (unlikely(skb->len >= READ_ONCE(dev->gso_max_size)))
+		return features & ~NETIF_F_GSO_MASK;
+
 	if (!skb_shinfo(skb)->gso_type) {
 		skb_warn_bad_offload(skb);
 		return features & ~NETIF_F_GSO_MASK;
@@ -3633,6 +3699,9 @@
 		return 0;
 
 	if (features & (NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM)) {
+		if (vlan_get_protocol(skb) == htons(ETH_P_IPV6) &&
+		    skb_network_header_len(skb) != sizeof(struct ipv6hdr))
+			goto sw_checksum;
 		switch (skb->csum_offset) {
 		case offsetof(struct tcphdr, check):
 		case offsetof(struct udphdr, check):
@@ -3640,6 +3709,7 @@
 		}
 	}
 
+sw_checksum:
 	return skb_checksum_help(skb);
 }
 EXPORT_SYMBOL(skb_csum_hwoffload_help);
@@ -3752,7 +3822,7 @@
 						sizeof(_tcphdr), &_tcphdr);
 			if (likely(th))
 				hdr_len += __tcp_hdrlen(th);
-		} else {
+		} else if (shinfo->gso_type & SKB_GSO_UDP_L4) {
 			struct udphdr _udphdr;
 
 			if (skb_header_pointer(skb, skb_transport_offset(skb),
@@ -3760,10 +3830,14 @@
 				hdr_len += sizeof(struct udphdr);
 		}
 
-		if (shinfo->gso_type & SKB_GSO_DODGY)
-			gso_segs = DIV_ROUND_UP(skb->len - hdr_len,
-						shinfo->gso_size);
+		if (unlikely(shinfo->gso_type & SKB_GSO_DODGY)) {
+			int payload = skb->len - hdr_len;
 
+			/* Malicious packet. */
+			if (payload <= 0)
+				return;
+			gso_segs = DIV_ROUND_UP(payload, shinfo->gso_size);
+		}
 		qdisc_skb_cb(skb)->pkt_len += (gso_segs - 1) * hdr_len;
 	}
 }
@@ -3932,8 +4006,8 @@
 		return skb;
 
 	/* qdisc_skb_cb(skb)->pkt_len was already set by the caller. */
-	qdisc_skb_cb(skb)->mru = 0;
-	qdisc_skb_cb(skb)->post_ct = false;
+	tc_skb_cb(skb)->mru = 0;
+	tc_skb_cb(skb)->post_ct = false;
 	mini_qdisc_bstats_cpu_update(miniq, skb);
 
 	switch (tcf_classify(skb, miniq->block, miniq->filter_list, &cl_res, false)) {
@@ -4139,6 +4213,7 @@
 	bool again = false;
 
 	skb_reset_mac_header(skb);
+	skb_assert_len(skb);
 
 	if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_SCHED_TSTAMP))
 		__skb_tstamp_tx(skb, NULL, NULL, skb->sk, SCM_TSTAMP_SCHED);
@@ -4193,7 +4268,10 @@
 	if (dev->flags & IFF_UP) {
 		int cpu = smp_processor_id(); /* ok because BHs are off */
 
-		if (txq->xmit_lock_owner != cpu) {
+		/* Other cpus might concurrently change txq->xmit_lock_owner
+		 * to -1 or to their cpu id, but not to our id.
+		 */
+		if (READ_ONCE(txq->xmit_lock_owner) != cpu) {
 			if (dev_xmit_recursion())
 				goto recursion_alert;
 
@@ -4442,8 +4520,10 @@
 		u32 next_cpu;
 		u32 ident;
 
-		/* First check into global flow table if there is a match */
-		ident = sock_flow_table->ents[hash & sock_flow_table->mask];
+		/* First check into global flow table if there is a match.
+		 * This READ_ONCE() pairs with WRITE_ONCE() from rps_record_sock_flow().
+		 */
+		ident = READ_ONCE(sock_flow_table->ents[hash & sock_flow_table->mask]);
 		if ((ident ^ hash) & ~rps_cpu_mask)
 			goto try_rps;
 
@@ -4578,7 +4658,7 @@
 	struct softnet_data *sd;
 	unsigned int old_flow, new_flow;
 
-	if (qlen < (netdev_max_backlog >> 1))
+	if (qlen < (READ_ONCE(netdev_max_backlog) >> 1))
 		return false;
 
 	sd = this_cpu_ptr(&softnet_data);
@@ -4626,7 +4706,7 @@
 	if (!netif_running(skb->dev))
 		goto drop;
 	qlen = skb_queue_len(&sd->input_pkt_queue);
-	if (qlen <= netdev_max_backlog && !skb_flow_limit(skb, qlen)) {
+	if (qlen <= READ_ONCE(netdev_max_backlog) && !skb_flow_limit(skb, qlen)) {
 		if (qlen) {
 enqueue:
 			__skb_queue_tail(&sd->input_pkt_queue, skb);
@@ -4882,7 +4962,7 @@
 {
 	int ret;
 
-	net_timestamp_check(netdev_tstamp_prequeue, skb);
+	net_timestamp_check(READ_ONCE(netdev_tstamp_prequeue), skb);
 
 	trace_netif_rx(skb);
 
@@ -4994,7 +5074,8 @@
 			if (likely(get_kfree_skb_cb(skb)->reason == SKB_REASON_CONSUMED))
 				trace_consume_skb(skb);
 			else
-				trace_kfree_skb(skb, net_tx_action);
+				trace_kfree_skb(skb, net_tx_action,
+						SKB_DROP_REASON_NOT_SPECIFIED);
 
 			if (skb->fclone != SKB_FCLONE_UNAVAILABLE)
 				__kfree_skb(skb);
@@ -5083,8 +5164,8 @@
 	}
 
 	qdisc_skb_cb(skb)->pkt_len = skb->len;
-	qdisc_skb_cb(skb)->mru = 0;
-	qdisc_skb_cb(skb)->post_ct = false;
+	tc_skb_cb(skb)->mru = 0;
+	tc_skb_cb(skb)->post_ct = false;
 	skb->tc_at_ingress = 1;
 	mini_qdisc_bstats_cpu_update(miniq, skb);
 
@@ -5241,7 +5322,7 @@
 	int ret = NET_RX_DROP;
 	__be16 type;
 
-	net_timestamp_check(!netdev_tstamp_prequeue, skb);
+	net_timestamp_check(!READ_ONCE(netdev_tstamp_prequeue), skb);
 
 	trace_netif_receive_skb(skb);
 
@@ -5622,7 +5703,7 @@
 {
 	int ret;
 
-	net_timestamp_check(netdev_tstamp_prequeue, skb);
+	net_timestamp_check(READ_ONCE(netdev_tstamp_prequeue), skb);
 
 	if (skb_defer_rx_timestamp(skb))
 		return NET_RX_SUCCESS;
@@ -5652,7 +5733,7 @@
 
 	INIT_LIST_HEAD(&sublist);
 	list_for_each_entry_safe(skb, next, head, list) {
-		net_timestamp_check(netdev_tstamp_prequeue, skb);
+		net_timestamp_check(READ_ONCE(netdev_tstamp_prequeue), skb);
 		skb_list_del_init(skb);
 		if (!skb_defer_rx_timestamp(skb))
 			list_add_tail(&skb->list, &sublist);
@@ -6425,7 +6506,7 @@
 		net_rps_action_and_irq_enable(sd);
 	}
 
-	napi->weight = dev_rx_weight;
+	napi->weight = READ_ONCE(dev_rx_weight);
 	while (again) {
 		struct sk_buff *skb;
 
@@ -7101,6 +7182,8 @@
 	void *have;
 
 	while (!napi_thread_wait(napi)) {
+		unsigned long last_qs = jiffies;
+
 		for (;;) {
 			bool repoll = false;
 
@@ -7115,6 +7198,7 @@
 			if (!repoll)
 				break;
 
+			rcu_softirq_qs_periodic(last_qs);
 			cond_resched();
 		}
 	}
@@ -7125,8 +7209,8 @@
 {
 	struct softnet_data *sd = this_cpu_ptr(&softnet_data);
 	unsigned long time_limit = jiffies +
-		usecs_to_jiffies(netdev_budget_usecs);
-	int budget = netdev_budget;
+		usecs_to_jiffies(READ_ONCE(netdev_budget_usecs));
+	int budget = READ_ONCE(netdev_budget);
 	LIST_HEAD(list);
 	LIST_HEAD(repoll);
 
@@ -9048,7 +9132,7 @@
 
 int dev_get_mac_address(struct sockaddr *sa, struct net *net, char *dev_name)
 {
-	size_t size = sizeof(sa->sa_data);
+	size_t size = sizeof(sa->sa_data_min);
 	struct net_device *dev;
 	int ret = 0;
 
@@ -9631,6 +9715,12 @@
 		goto out_unlock;
 	}
 	old_prog = link->prog;
+	if (old_prog->type != new_prog->type ||
+	    old_prog->expected_attach_type != new_prog->expected_attach_type) {
+		err = -EINVAL;
+		goto out_unlock;
+	}
+
 	if (old_prog == new_prog) {
 		/* no-op, don't disturb drivers */
 		bpf_prog_put(new_prog);
@@ -10304,11 +10394,11 @@
 		goto err_uninit;
 
 	ret = netdev_register_kobject(dev);
-	if (ret) {
-		dev->reg_state = NETREG_UNREGISTERED;
+	write_lock(&dev_base_lock);
+	dev->reg_state = ret ? NETREG_UNREGISTERED : NETREG_REGISTERED;
+	write_unlock(&dev_base_lock);
+	if (ret)
 		goto err_uninit;
-	}
-	dev->reg_state = NETREG_REGISTERED;
 
 	__netdev_update_features(dev);
 
@@ -10468,8 +10558,6 @@
 	unsigned long rebroadcast_time, warning_time;
 	int wait = 0, refcnt;
 
-	linkwatch_forget_dev(dev);
-
 	rebroadcast_time = warning_time = jiffies;
 	refcnt = netdev_refcnt_read(dev);
 
@@ -10500,8 +10588,9 @@
 			rebroadcast_time = jiffies;
 		}
 
+		rcu_barrier();
+
 		if (!wait) {
-			rcu_barrier();
 			wait = WAIT_REFS_MIN_MSECS;
 		} else {
 			msleep(wait);
@@ -10515,6 +10604,7 @@
 			       netdev_unregister_timeout_secs * HZ)) {
 			pr_emerg("unregister_netdevice: waiting for %s to become free. Usage count = %d\n",
 				 dev->name, refcnt);
+			ref_tracker_dir_print(&dev->refcnt_tracker, 10);
 			warning_time = jiffies;
 		}
 	}
@@ -10583,7 +10673,10 @@
 			continue;
 		}
 
+		write_lock(&dev_base_lock);
 		dev->reg_state = NETREG_UNREGISTERED;
+		write_unlock(&dev_base_lock);
+		linkwatch_forget_dev(dev);
 
 		netdev_wait_allrefs(dev);
 
@@ -10593,9 +10686,7 @@
 		BUG_ON(!list_empty(&dev->ptype_specific));
 		WARN_ON(rcu_access_pointer(dev->ip_ptr));
 		WARN_ON(rcu_access_pointer(dev->ip6_ptr));
-#if IS_ENABLED(CONFIG_DECNET)
-		WARN_ON(dev->dn_ptr);
-#endif
+
 		if (dev->priv_destructor)
 			dev->priv_destructor(dev);
 		if (dev->needs_free_netdev)
@@ -10620,24 +10711,16 @@
 void netdev_stats_to_stats64(struct rtnl_link_stats64 *stats64,
 			     const struct net_device_stats *netdev_stats)
 {
-#if BITS_PER_LONG == 64
-	BUILD_BUG_ON(sizeof(*stats64) < sizeof(*netdev_stats));
-	memcpy(stats64, netdev_stats, sizeof(*netdev_stats));
-	/* zero out counters that only exist in rtnl_link_stats64 */
-	memset((char *)stats64 + sizeof(*netdev_stats), 0,
-	       sizeof(*stats64) - sizeof(*netdev_stats));
-#else
-	size_t i, n = sizeof(*netdev_stats) / sizeof(unsigned long);
-	const unsigned long *src = (const unsigned long *)netdev_stats;
+	size_t i, n = sizeof(*netdev_stats) / sizeof(atomic_long_t);
+	const atomic_long_t *src = (atomic_long_t *)netdev_stats;
 	u64 *dst = (u64 *)stats64;
 
 	BUILD_BUG_ON(n > sizeof(*stats64) / sizeof(u64));
 	for (i = 0; i < n; i++)
-		dst[i] = src[i];
+		dst[i] = (unsigned long)atomic_long_read(&src[i]);
 	/* zero out counters that only exist in rtnl_link_stats64 */
 	memset((char *)stats64 + n * sizeof(u64), 0,
 	       sizeof(*stats64) - n * sizeof(u64));
-#endif
 }
 EXPORT_SYMBOL(netdev_stats_to_stats64);
 
@@ -10805,6 +10888,7 @@
 	dev = PTR_ALIGN(p, NETDEV_ALIGN);
 	dev->padded = (char *)dev - (char *)p;
 
+	ref_tracker_dir_init(&dev->refcnt_tracker, 128);
 #ifdef CONFIG_PCPU_DEV_REFCNT
 	dev->pcpu_refcnt = alloc_percpu(int);
 	if (!dev->pcpu_refcnt)
@@ -10921,6 +11005,7 @@
 	list_for_each_entry_safe(p, n, &dev->napi_list, dev_list)
 		netif_napi_del(p);
 
+	ref_tracker_dir_exit(&dev->refcnt_tracker);
 #ifdef CONFIG_PCPU_DEV_REFCNT
 	free_percpu(dev->pcpu_refcnt);
 	dev->pcpu_refcnt = NULL;
@@ -11028,9 +11113,10 @@
 
 	list_for_each_entry(dev, head, unreg_list) {
 		/* And unlink it from device chain. */
-		unlist_netdevice(dev);
-
+		write_lock(&dev_base_lock);
+		unlist_netdevice(dev, false);
 		dev->reg_state = NETREG_UNREGISTERING;
+		write_unlock(&dev_base_lock);
 	}
 	flush_all_backlogs();
 
@@ -11131,6 +11217,7 @@
 			       const char *pat, int new_ifindex)
 {
 	struct net *net_old = dev_net(dev);
+	char new_name[IFNAMSIZ] = {};
 	int err, new_nsid;
 
 	ASSERT_RTNL();
@@ -11153,11 +11240,11 @@
 	 * we can use it in the destination network namespace.
 	 */
 	err = -EEXIST;
-	if (__dev_get_by_name(net, dev->name)) {
+	if (netdev_name_in_use(net, dev->name)) {
 		/* We get here if we can't use the current device name */
 		if (!pat)
 			goto out;
-		err = dev_get_valid_name(net, dev, pat);
+		err = dev_prep_valid_name(net, dev, pat, new_name);
 		if (err < 0)
 			goto out;
 	}
@@ -11175,7 +11262,7 @@
 	dev_close(dev);
 
 	/* And unlink it from device chain */
-	unlist_netdevice(dev);
+	unlist_netdevice(dev, true);
 
 	synchronize_net();
 
@@ -11225,6 +11312,9 @@
 	kobject_uevent(&dev->dev.kobj, KOBJ_ADD);
 	netdev_adjacent_add_links(dev);
 
+	if (new_name[0]) /* Rename the netdev to prepared name */
+		strscpy(dev->name, new_name, IFNAMSIZ);
+
 	/* Fixup kobjects */
 	err = device_rename(&dev->dev, dev->name);
 	WARN_ON(err);
@@ -11367,8 +11457,7 @@
 	BUILD_BUG_ON(GRO_HASH_BUCKETS >
 		     8 * sizeof_field(struct napi_struct, gro_bitmask));
 
-	if (net != &init_net)
-		INIT_LIST_HEAD(&net->dev_base_head);
+	INIT_LIST_HEAD(&net->dev_base_head);
 
 	net->dev_name_head = netdev_create_hash();
 	if (net->dev_name_head == NULL)
@@ -11506,7 +11595,7 @@
 
 		/* Push remaining network devices to init_net */
 		snprintf(fb_name, IFNAMSIZ, "dev%d", dev->ifindex);
-		if (__dev_get_by_name(&init_net, fb_name))
+		if (netdev_name_in_use(&init_net, fb_name))
 			snprintf(fb_name, IFNAMSIZ, "dev%%d");
 		err = dev_change_net_namespace(dev, &init_net, fb_name);
 		if (err) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/dev_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/dev_ioctl.c
@@ -339,7 +339,7 @@
 		if (ifr->ifr_hwaddr.sa_family != dev->type)
 			return -EINVAL;
 		memcpy(dev->broadcast, ifr->ifr_hwaddr.sa_data,
-		       min(sizeof(ifr->ifr_hwaddr.sa_data),
+		       min(sizeof(ifr->ifr_hwaddr.sa_data_min),
 			   (size_t)dev->addr_len));
 		call_netdevice_notifiers(NETDEV_CHANGEADDR, dev);
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/devlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/devlink.c
@@ -4031,14 +4031,6 @@
 		return err;
 	}
 
-	if (info->attrs[DEVLINK_ATTR_NETNS_PID] ||
-	    info->attrs[DEVLINK_ATTR_NETNS_FD] ||
-	    info->attrs[DEVLINK_ATTR_NETNS_ID]) {
-		dest_net = devlink_netns_get(skb, info);
-		if (IS_ERR(dest_net))
-			return PTR_ERR(dest_net);
-	}
-
 	if (info->attrs[DEVLINK_ATTR_RELOAD_ACTION])
 		action = nla_get_u8(info->attrs[DEVLINK_ATTR_RELOAD_ACTION]);
 	else
@@ -4081,6 +4073,14 @@
 			return -EINVAL;
 		}
 	}
+	if (info->attrs[DEVLINK_ATTR_NETNS_PID] ||
+	    info->attrs[DEVLINK_ATTR_NETNS_FD] ||
+	    info->attrs[DEVLINK_ATTR_NETNS_ID]) {
+		dest_net = devlink_netns_get(skb, info);
+		if (IS_ERR(dest_net))
+			return PTR_ERR(dest_net);
+	}
+
 	err = devlink_reload(devlink, dest_net, action, limit, &actions_performed, info->extack);
 
 	if (dest_net)
@@ -8795,8 +8795,6 @@
 			    GENL_DONT_VALIDATE_DUMP_STRICT,
 		.dumpit = devlink_nl_cmd_health_reporter_dump_get_dumpit,
 		.flags = GENL_ADMIN_PERM,
-		.internal_flags = DEVLINK_NL_FLAG_NEED_DEVLINK_OR_PORT |
-				  DEVLINK_NL_FLAG_NO_LOCK,
 	},
 	{
 		.cmd = DEVLINK_CMD_HEALTH_REPORTER_DUMP_CLEAR,
@@ -9057,7 +9055,10 @@
 
 static void devlink_port_type_warn(struct work_struct *work)
 {
-	WARN(true, "Type was not set for devlink port.");
+	struct devlink_port *port = container_of(to_delayed_work(work),
+						 struct devlink_port,
+						 type_warn_dw);
+	dev_warn(port->devlink->dev, "Type was not set for devlink port.");
 }
 
 static bool devlink_port_type_should_warn(struct devlink_port *devlink_port)
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/drop_monitor.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/drop_monitor.c
@@ -73,7 +73,7 @@
 };
 
 struct per_cpu_dm_data {
-	spinlock_t		lock;	/* Protects 'skb', 'hw_entries' and
+	raw_spinlock_t		lock;	/* Protects 'skb', 'hw_entries' and
 					 * 'send_timer'
 					 */
 	union {
@@ -110,7 +110,8 @@
 
 struct net_dm_alert_ops {
 	void (*kfree_skb_probe)(void *ignore, struct sk_buff *skb,
-				void *location);
+				void *location,
+				enum skb_drop_reason reason);
 	void (*napi_poll_probe)(void *ignore, struct napi_struct *napi,
 				int work, int budget);
 	void (*work_item_func)(struct work_struct *work);
@@ -168,9 +169,9 @@
 err:
 	mod_timer(&data->send_timer, jiffies + HZ / 10);
 out:
-	spin_lock_irqsave(&data->lock, flags);
+	raw_spin_lock_irqsave(&data->lock, flags);
 	swap(data->skb, skb);
-	spin_unlock_irqrestore(&data->lock, flags);
+	raw_spin_unlock_irqrestore(&data->lock, flags);
 
 	if (skb) {
 		struct nlmsghdr *nlh = (struct nlmsghdr *)skb->data;
@@ -183,7 +184,7 @@
 }
 
 static const struct genl_multicast_group dropmon_mcgrps[] = {
-	{ .name = "events", },
+	{ .name = "events", .cap_sys_admin = 1 },
 };
 
 static void send_dm_alert(struct work_struct *work)
@@ -225,7 +226,7 @@
 
 	local_irq_save(flags);
 	data = this_cpu_ptr(&dm_cpu_data);
-	spin_lock(&data->lock);
+	raw_spin_lock(&data->lock);
 	dskb = data->skb;
 
 	if (!dskb)
@@ -259,10 +260,12 @@
 	}
 
 out:
-	spin_unlock_irqrestore(&data->lock, flags);
+	raw_spin_unlock_irqrestore(&data->lock, flags);
 }
 
-static void trace_kfree_skb_hit(void *ignore, struct sk_buff *skb, void *location)
+static void trace_kfree_skb_hit(void *ignore, struct sk_buff *skb,
+				void *location,
+				enum skb_drop_reason reason)
 {
 	trace_drop_common(skb, location);
 }
@@ -280,13 +283,17 @@
 
 	rcu_read_lock();
 	list_for_each_entry_rcu(new_stat, &hw_stats_list, list) {
+		struct net_device *dev;
+
 		/*
 		 * only add a note to our monitor buffer if:
 		 * 1) this is the dev we received on
 		 * 2) its after the last_rx delta
 		 * 3) our rx_dropped count has gone up
 		 */
-		if ((new_stat->dev == napi->dev)  &&
+		/* Paired with WRITE_ONCE() in dropmon_net_event() */
+		dev = READ_ONCE(new_stat->dev);
+		if ((dev == napi->dev)  &&
 		    (time_after(jiffies, new_stat->last_rx + dm_hw_check_delta)) &&
 		    (napi->dev->stats.rx_dropped != new_stat->last_drop_val)) {
 			trace_drop_common(NULL, NULL);
@@ -314,9 +321,9 @@
 		mod_timer(&hw_data->send_timer, jiffies + HZ / 10);
 	}
 
-	spin_lock_irqsave(&hw_data->lock, flags);
+	raw_spin_lock_irqsave(&hw_data->lock, flags);
 	swap(hw_data->hw_entries, hw_entries);
-	spin_unlock_irqrestore(&hw_data->lock, flags);
+	raw_spin_unlock_irqrestore(&hw_data->lock, flags);
 
 	return hw_entries;
 }
@@ -448,7 +455,7 @@
 		return;
 
 	hw_data = this_cpu_ptr(&dm_hw_cpu_data);
-	spin_lock_irqsave(&hw_data->lock, flags);
+	raw_spin_lock_irqsave(&hw_data->lock, flags);
 	hw_entries = hw_data->hw_entries;
 
 	if (!hw_entries)
@@ -466,7 +473,7 @@
 		goto out;
 
 	hw_entry = &hw_entries->entries[hw_entries->num_entries];
-	strlcpy(hw_entry->trap_name, metadata->trap_name,
+	strscpy(hw_entry->trap_name, metadata->trap_name,
 		NET_DM_MAX_HW_TRAP_NAME_LEN - 1);
 	hw_entry->count = 1;
 	hw_entries->num_entries++;
@@ -477,7 +484,7 @@
 	}
 
 out:
-	spin_unlock_irqrestore(&hw_data->lock, flags);
+	raw_spin_unlock_irqrestore(&hw_data->lock, flags);
 }
 
 static const struct net_dm_alert_ops net_dm_alert_summary_ops = {
@@ -490,7 +497,8 @@
 
 static void net_dm_packet_trace_kfree_skb_hit(void *ignore,
 					      struct sk_buff *skb,
-					      void *location)
+					      void *location,
+					      enum skb_drop_reason reason)
 {
 	ktime_t tstamp = ktime_get_real();
 	struct per_cpu_dm_data *data;
@@ -1572,7 +1580,10 @@
 		mutex_lock(&net_dm_mutex);
 		list_for_each_entry_safe(new_stat, tmp, &hw_stats_list, list) {
 			if (new_stat->dev == dev) {
-				new_stat->dev = NULL;
+
+				/* Paired with READ_ONCE() in trace_napi_poll_hit() */
+				WRITE_ONCE(new_stat->dev, NULL);
+
 				if (trace_state == TRACE_OFF) {
 					list_del_rcu(&new_stat->list);
 					kfree_rcu(new_stat, rcu);
@@ -1607,11 +1618,13 @@
 		.cmd = NET_DM_CMD_START,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
 		.doit = net_dm_cmd_trace,
+		.flags = GENL_ADMIN_PERM,
 	},
 	{
 		.cmd = NET_DM_CMD_STOP,
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
 		.doit = net_dm_cmd_trace,
+		.flags = GENL_ADMIN_PERM,
 	},
 	{
 		.cmd = NET_DM_CMD_CONFIG_GET,
@@ -1658,7 +1671,7 @@
 
 static void __net_dm_cpu_data_init(struct per_cpu_dm_data *data)
 {
-	spin_lock_init(&data->lock);
+	raw_spin_lock_init(&data->lock);
 	skb_queue_head_init(&data->drop_queue);
 	u64_stats_init(&data->stats.syncp);
 }
@@ -1716,30 +1729,30 @@
 		return -ENOSPC;
 	}
 
-	rc = genl_register_family(&net_drop_monitor_family);
-	if (rc) {
-		pr_err("Could not create drop monitor netlink family\n");
-		return rc;
+	for_each_possible_cpu(cpu) {
+		net_dm_cpu_data_init(cpu);
+		net_dm_hw_cpu_data_init(cpu);
 	}
-	WARN_ON(net_drop_monitor_family.mcgrp_offset != NET_DM_GRP_ALERT);
 
 	rc = register_netdevice_notifier(&dropmon_net_notifier);
 	if (rc < 0) {
 		pr_crit("Failed to register netdevice notifier\n");
+		return rc;
+	}
+
+	rc = genl_register_family(&net_drop_monitor_family);
+	if (rc) {
+		pr_err("Could not create drop monitor netlink family\n");
 		goto out_unreg;
 	}
+	WARN_ON(net_drop_monitor_family.mcgrp_offset != NET_DM_GRP_ALERT);
 
 	rc = 0;
 
-	for_each_possible_cpu(cpu) {
-		net_dm_cpu_data_init(cpu);
-		net_dm_hw_cpu_data_init(cpu);
-	}
-
 	goto out;
 
 out_unreg:
-	genl_unregister_family(&net_drop_monitor_family);
+	WARN_ON(unregister_netdevice_notifier(&dropmon_net_notifier));
 out:
 	return rc;
 }
@@ -1748,19 +1761,18 @@
 {
 	int cpu;
 
-	BUG_ON(unregister_netdevice_notifier(&dropmon_net_notifier));
-
 	/*
 	 * Because of the module_get/put we do in the trace state change path
 	 * we are guaranteed not to have any current users when we get here
 	 */
+	BUG_ON(genl_unregister_family(&net_drop_monitor_family));
+
+	BUG_ON(unregister_netdevice_notifier(&dropmon_net_notifier));
 
 	for_each_possible_cpu(cpu) {
 		net_dm_hw_cpu_data_fini(cpu);
 		net_dm_cpu_data_fini(cpu);
 	}
-
-	BUG_ON(genl_unregister_family(&net_drop_monitor_family));
 }
 
 module_init(init_net_drop_monitor);
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/dst.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/dst.c
@@ -82,12 +82,8 @@
 
 	if (ops->gc &&
 	    !(flags & DST_NOCOUNT) &&
-	    dst_entries_get_fast(ops) > ops->gc_thresh) {
-		if (ops->gc(ops)) {
-			pr_notice_ratelimited("Route cache is full: consider increasing sysctl net.ipv6.route.max_size.\n");
-			return NULL;
-		}
-	}
+	    dst_entries_get_fast(ops) > ops->gc_thresh)
+		ops->gc(ops);
 
 	dst = kmem_cache_alloc(ops->kmem_cachep, GFP_ATOMIC);
 	if (!dst)
@@ -112,9 +108,6 @@
 		child = xdst->child;
 	}
 #endif
-	if (!(dst->flags & DST_NOCOUNT))
-		dst_entries_add(dst->ops, -1);
-
 	if (dst->ops->destroy)
 		dst->ops->destroy(dst);
 	dev_put(dst->dev);
@@ -164,6 +157,12 @@
 }
 EXPORT_SYMBOL(dst_dev_put);
 
+static void dst_count_dec(struct dst_entry *dst)
+{
+	if (!(dst->flags & DST_NOCOUNT))
+		dst_entries_add(dst->ops, -1);
+}
+
 void dst_release(struct dst_entry *dst)
 {
 	if (dst) {
@@ -173,8 +172,10 @@
 		if (WARN_ONCE(newrefcnt < 0, "dst_release underflow"))
 			net_warn_ratelimited("%s: dst:%p refcnt:%d\n",
 					     __func__, dst, newrefcnt);
-		if (!newrefcnt)
+		if (!newrefcnt){
+			dst_count_dec(dst);
 			call_rcu(&dst->rcu_head, dst_destroy_rcu);
+		}
 	}
 }
 EXPORT_SYMBOL(dst_release);
@@ -188,8 +189,10 @@
 		if (WARN_ONCE(newrefcnt < 0, "dst_release_immediate underflow"))
 			net_warn_ratelimited("%s: dst:%p refcnt:%d\n",
 					     __func__, dst, newrefcnt);
-		if (!newrefcnt)
+		if (!newrefcnt){
+			dst_count_dec(dst);
 			dst_destroy(dst);
+		}
 	}
 }
 EXPORT_SYMBOL(dst_release_immediate);
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/dst_cache.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/dst_cache.c
@@ -162,3 +162,22 @@
 	free_percpu(dst_cache->cache);
 }
 EXPORT_SYMBOL_GPL(dst_cache_destroy);
+
+void dst_cache_reset_now(struct dst_cache *dst_cache)
+{
+	int i;
+
+	if (!dst_cache->cache)
+		return;
+
+	dst_cache->reset_ts = jiffies;
+	for_each_possible_cpu(i) {
+		struct dst_cache_pcpu *idst = per_cpu_ptr(dst_cache->cache, i);
+		struct dst_entry *dst = idst->dst;
+
+		idst->cookie = 0;
+		idst->dst = NULL;
+		dst_release(dst);
+	}
+}
+EXPORT_SYMBOL_GPL(dst_cache_reset_now);
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/fib_rules.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/fib_rules.c
@@ -323,7 +323,7 @@
 		if (!err && ops->suppress && INDIRECT_CALL_MT(ops->suppress,
 							      fib6_rule_suppress,
 							      fib4_rule_suppress,
-							      rule, arg))
+							      rule, flags, arg))
 			continue;
 
 		if (err != -EAGAIN) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/filter.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/filter.c
@@ -79,6 +79,9 @@
 #include <net/tls.h>
 #include <net/xdp.h>
 
+/* Keep the struct bpf_fib_lookup small so that it fits into a cacheline */
+static_assert(sizeof(struct bpf_fib_lookup) == 64, "struct bpf_fib_lookup size check");
+
 static const struct bpf_func_proto *
 bpf_sk_base_func_proto(enum bpf_func_id func_id);
 
@@ -1213,10 +1216,11 @@
 static bool __sk_filter_charge(struct sock *sk, struct sk_filter *fp)
 {
 	u32 filter_size = bpf_prog_size(fp->prog->len);
+	int optmem_max = READ_ONCE(sysctl_optmem_max);
 
 	/* same check as in sock_kmalloc() */
-	if (filter_size <= sysctl_optmem_max &&
-	    atomic_read(&sk->sk_omem_alloc) + filter_size < sysctl_optmem_max) {
+	if (filter_size <= optmem_max &&
+	    atomic_read(&sk->sk_omem_alloc) + filter_size < optmem_max) {
 		atomic_add(filter_size, &sk->sk_omem_alloc);
 		return true;
 	}
@@ -1548,7 +1552,7 @@
 	if (IS_ERR(prog))
 		return PTR_ERR(prog);
 
-	if (bpf_prog_size(prog->len) > sysctl_optmem_max)
+	if (bpf_prog_size(prog->len) > READ_ONCE(sysctl_optmem_max))
 		err = -ENOMEM;
 	else
 		err = reuseport_attach_prog(sk, prog);
@@ -1615,7 +1619,7 @@
 		}
 	} else {
 		/* BPF_PROG_TYPE_SOCKET_FILTER */
-		if (bpf_prog_size(prog->len) > sysctl_optmem_max) {
+		if (bpf_prog_size(prog->len) > READ_ONCE(sysctl_optmem_max)) {
 			err = -ENOMEM;
 			goto err_prog_put;
 		}
@@ -1688,7 +1692,7 @@
 
 	if (unlikely(flags & ~(BPF_F_RECOMPUTE_CSUM | BPF_F_INVALIDATE_HASH)))
 		return -EINVAL;
-	if (unlikely(offset > 0xffff))
+	if (unlikely(offset > INT_MAX))
 		return -EFAULT;
 	if (unlikely(bpf_try_make_writable(skb, offset + len)))
 		return -EFAULT;
@@ -1713,7 +1717,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
-	.arg3_type	= ARG_PTR_TO_MEM,
+	.arg3_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE,
 	.arg5_type	= ARG_ANYTHING,
 };
@@ -1723,7 +1727,7 @@
 {
 	void *ptr;
 
-	if (unlikely(offset > 0xffff))
+	if (unlikely(offset > INT_MAX))
 		goto err_clear;
 
 	ptr = skb_header_pointer(skb, offset, len, to);
@@ -2018,9 +2022,9 @@
 	.gpl_only	= false,
 	.pkt_access	= true,
 	.ret_type	= RET_INTEGER,
-	.arg1_type	= ARG_PTR_TO_MEM_OR_NULL,
+	.arg1_type	= ARG_PTR_TO_MEM | PTR_MAYBE_NULL | MEM_RDONLY,
 	.arg2_type	= ARG_CONST_SIZE_OR_ZERO,
-	.arg3_type	= ARG_PTR_TO_MEM_OR_NULL,
+	.arg3_type	= ARG_PTR_TO_MEM | PTR_MAYBE_NULL | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE_OR_ZERO,
 	.arg5_type	= ARG_ANYTHING,
 };
@@ -2122,8 +2126,17 @@
 {
 	unsigned int mlen = skb_network_offset(skb);
 
+	if (unlikely(skb->len <= mlen)) {
+		kfree_skb(skb);
+		return -ERANGE;
+	}
+
 	if (mlen) {
 		__skb_pull(skb, mlen);
+		if (unlikely(!skb->len)) {
+			kfree_skb(skb);
+			return -ERANGE;
+		}
 
 		/* At ingress, the mac header has already been pulled once.
 		 * At egress, skb_pospull_rcsum has to be done in case that
@@ -2143,7 +2156,7 @@
 				 u32 flags)
 {
 	/* Verify that a link layer header is carried */
-	if (unlikely(skb->mac_header >= skb->network_header)) {
+	if (unlikely(skb->mac_header >= skb->network_header || skb->len == 0)) {
 		kfree_skb(skb);
 		return -ERANGE;
 	}
@@ -2392,9 +2405,9 @@
 
 /* Internal, non-exposed redirect flags. */
 enum {
-	BPF_F_NEIGH	= (1ULL << 1),
-	BPF_F_PEER	= (1ULL << 2),
-	BPF_F_NEXTHOP	= (1ULL << 3),
+	BPF_F_NEIGH	= (1ULL << 16),
+	BPF_F_PEER	= (1ULL << 17),
+	BPF_F_NEXTHOP	= (1ULL << 18),
 #define BPF_F_REDIRECT_INTERNAL	(BPF_F_NEIGH | BPF_F_PEER | BPF_F_NEXTHOP)
 };
 
@@ -2404,6 +2417,8 @@
 	struct sk_buff *clone;
 	int ret;
 
+	BUILD_BUG_ON(BPF_F_REDIRECT_INTERNAL & BPF_F_REDIRECT_FLAGS);
+
 	if (unlikely(flags & (~(BPF_F_INGRESS) | BPF_F_REDIRECT_INTERNAL)))
 		return -EINVAL;
 
@@ -2541,7 +2556,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_ANYTHING,
-	.arg2_type      = ARG_PTR_TO_MEM_OR_NULL,
+	.arg2_type      = ARG_PTR_TO_MEM | PTR_MAYBE_NULL | MEM_RDONLY,
 	.arg3_type      = ARG_CONST_SIZE_OR_ZERO,
 	.arg4_type	= ARG_ANYTHING,
 };
@@ -2566,6 +2581,20 @@
 	return 0;
 }
 
+static void sk_msg_reset_curr(struct sk_msg *msg)
+{
+	if (!msg->sg.size) {
+		msg->sg.curr = msg->sg.start;
+		msg->sg.copybreak = 0;
+	} else {
+		u32 i = msg->sg.end;
+
+		sk_msg_iter_var_prev(i);
+		msg->sg.curr = i;
+		msg->sg.copybreak = msg->sg.data[i].length;
+	}
+}
+
 static const struct bpf_func_proto bpf_msg_cork_bytes_proto = {
 	.func           = bpf_msg_cork_bytes,
 	.gpl_only       = false,
@@ -2685,6 +2714,7 @@
 		      msg->sg.end - shift + NR_MSG_FRAG_IDS :
 		      msg->sg.end - shift;
 out:
+	sk_msg_reset_curr(msg);
 	msg->data = sg_virt(&msg->sg.data[first_sge]) + start - offset;
 	msg->data_end = msg->data + bytes;
 	return 0;
@@ -2711,6 +2741,9 @@
 	if (unlikely(flags))
 		return -EINVAL;
 
+	if (unlikely(len == 0))
+		return 0;
+
 	/* First find the starting scatterlist element */
 	i = msg->sg.start;
 	do {
@@ -2722,7 +2755,7 @@
 		sk_msg_iter_var_next(i);
 	} while (i != msg->sg.end);
 
-	if (start >= offset + l)
+	if (start > offset + l)
 		return -EINVAL;
 
 	space = MAX_MSG_FRAGS - sk_msg_elem_used(msg);
@@ -2747,6 +2780,8 @@
 
 		raw = page_address(page);
 
+		if (i == msg->sg.end)
+			sk_msg_iter_var_prev(i);
 		psge = sk_msg_elem(msg, i);
 		front = start - offset;
 		back = psge->length - front;
@@ -2763,7 +2798,13 @@
 		}
 
 		put_page(sg_page(psge));
-	} else if (start - offset) {
+		new = i;
+		goto place_new;
+	}
+
+	if (start - offset) {
+		if (i == msg->sg.end)
+			sk_msg_iter_var_prev(i);
 		psge = sk_msg_elem(msg, i);
 		rsge = sk_msg_elem_cpy(msg, i);
 
@@ -2774,39 +2815,44 @@
 		sk_msg_iter_var_next(i);
 		sg_unmark_end(psge);
 		sg_unmark_end(&rsge);
-		sk_msg_iter_next(msg, end);
 	}
 
 	/* Slot(s) to place newly allocated data */
+	sk_msg_iter_next(msg, end);
 	new = i;
+	sk_msg_iter_var_next(i);
+
+	if (i == msg->sg.end) {
+		if (!rsge.length)
+			goto place_new;
+		sk_msg_iter_next(msg, end);
+		goto place_new;
+	}
 
 	/* Shift one or two slots as needed */
-	if (!copy) {
-		sge = sk_msg_elem_cpy(msg, i);
+	sge = sk_msg_elem_cpy(msg, new);
+	sg_unmark_end(&sge);
 
+	nsge = sk_msg_elem_cpy(msg, i);
+	if (rsge.length) {
 		sk_msg_iter_var_next(i);
-		sg_unmark_end(&sge);
+		nnsge = sk_msg_elem_cpy(msg, i);
 		sk_msg_iter_next(msg, end);
+	}
 
-		nsge = sk_msg_elem_cpy(msg, i);
+	while (i != msg->sg.end) {
+		msg->sg.data[i] = sge;
+		sge = nsge;
+		sk_msg_iter_var_next(i);
 		if (rsge.length) {
-			sk_msg_iter_var_next(i);
+			nsge = nnsge;
 			nnsge = sk_msg_elem_cpy(msg, i);
-		}
-
-		while (i != msg->sg.end) {
-			msg->sg.data[i] = sge;
-			sge = nsge;
-			sk_msg_iter_var_next(i);
-			if (rsge.length) {
-				nsge = nnsge;
-				nnsge = sk_msg_elem_cpy(msg, i);
-			} else {
-				nsge = sk_msg_elem_cpy(msg, i);
-			}
+		} else {
+			nsge = sk_msg_elem_cpy(msg, i);
 		}
 	}
 
+place_new:
 	/* Place newly allocated data buffer */
 	sk_mem_charge(msg->sk, len);
 	msg->sg.size += len;
@@ -2818,6 +2864,7 @@
 		msg->sg.data[new] = rsge;
 	}
 
+	sk_msg_reset_curr(msg);
 	sk_msg_compute_data_pointers(msg);
 	return 0;
 }
@@ -2834,8 +2881,10 @@
 
 static void sk_msg_shift_left(struct sk_msg *msg, int i)
 {
+	struct scatterlist *sge = sk_msg_elem(msg, i);
 	int prev;
 
+	put_page(sg_page(sge));
 	do {
 		prev = i;
 		sk_msg_iter_var_next(i);
@@ -2872,6 +2921,9 @@
 	if (unlikely(flags))
 		return -EINVAL;
 
+	if (unlikely(len == 0))
+		return 0;
+
 	/* First find the starting scatterlist element */
 	i = msg->sg.start;
 	do {
@@ -2884,7 +2936,7 @@
 	} while (i != msg->sg.end);
 
 	/* Bounds checks: start and pop must be inside message */
-	if (start >= offset + l || last >= msg->sg.size)
+	if (start >= offset + l || last > msg->sg.size)
 		return -EINVAL;
 
 	space = MAX_MSG_FRAGS - sk_msg_elem_used(msg);
@@ -2913,12 +2965,12 @@
 	 */
 	if (start != offset) {
 		struct scatterlist *nsge, *sge = sk_msg_elem(msg, i);
-		int a = start;
+		int a = start - offset;
 		int b = sge->length - pop - a;
 
 		sk_msg_iter_var_next(i);
 
-		if (pop < sge->length - a) {
+		if (b > 0) {
 			if (space) {
 				sge->length = a;
 				sk_msg_shift_right(msg, i);
@@ -2937,7 +2989,6 @@
 				if (unlikely(!page))
 					return -ENOMEM;
 
-				sge->length = a;
 				orig = sg_page(sge);
 				from = sg_virt(sge);
 				to = page_address(page);
@@ -2947,7 +2998,7 @@
 				put_page(orig);
 			}
 			pop = 0;
-		} else if (pop >= sge->length - a) {
+		} else {
 			pop -= (sge->length - a);
 			sge->length = a;
 		}
@@ -2981,11 +3032,11 @@
 			pop -= sge->length;
 			sk_msg_shift_left(msg, i);
 		}
-		sk_msg_iter_var_next(i);
 	}
 
 	sk_mem_uncharge(msg->sk, len - pop);
 	msg->sg.size -= (len - pop);
+	sk_msg_reset_curr(msg);
 	sk_msg_compute_data_pointers(msg);
 	return 0;
 }
@@ -3169,15 +3220,18 @@
 
 static int bpf_skb_generic_pop(struct sk_buff *skb, u32 off, u32 len)
 {
+	void *old_data;
+
 	/* skb_ensure_writable() is not needed here, as we're
 	 * already working on an uncloned skb.
 	 */
 	if (unlikely(!pskb_may_pull(skb, off + len)))
 		return -ENOMEM;
 
-	skb_postpull_rcsum(skb, skb->data + off, len);
-	memmove(skb->data + len, skb->data, off);
+	old_data = skb->data;
 	__skb_pull(skb, len);
+	skb_postpull_rcsum(skb, old_data + off, len);
+	memmove(skb->data, old_data, off);
 
 	return 0;
 }
@@ -3469,13 +3523,20 @@
 	if (skb_is_gso(skb)) {
 		struct skb_shared_info *shinfo = skb_shinfo(skb);
 
-		/* Due to header grow, MSS needs to be downgraded. */
-		if (!(flags & BPF_F_ADJ_ROOM_FIXED_GSO))
-			skb_decrease_gso_size(shinfo, len_diff);
-
 		/* Header must be checked, and gso_segs recomputed. */
 		shinfo->gso_type |= gso_type;
 		shinfo->gso_segs = 0;
+
+		/* Due to header growth, MSS needs to be downgraded.
+		 * There is a BUG_ON() when segmenting the frag_list with
+		 * head_frag true, so linearize the skb after downgrading
+		 * the MSS.
+		 */
+		if (!(flags & BPF_F_ADJ_ROOM_FIXED_GSO)) {
+			skb_decrease_gso_size(shinfo, len_diff);
+			if (shinfo->frag_list)
+				return skb_linearize(skb);
+		}
 	}
 
 	return 0;
@@ -3622,13 +3683,22 @@
 
 static u32 __bpf_skb_min_len(const struct sk_buff *skb)
 {
-	u32 min_len = skb_network_offset(skb);
+	int offset = skb_network_offset(skb);
+	u32 min_len = 0;
 
-	if (skb_transport_header_was_set(skb))
-		min_len = skb_transport_offset(skb);
-	if (skb->ip_summed == CHECKSUM_PARTIAL)
-		min_len = skb_checksum_start_offset(skb) +
-			  skb->csum_offset + sizeof(__sum16);
+	if (offset > 0)
+		min_len = offset;
+	if (skb_transport_header_was_set(skb)) {
+		offset = skb_transport_offset(skb);
+		if (offset > 0)
+			min_len = offset;
+	}
+	if (skb->ip_summed == CHECKSUM_PARTIAL) {
+		offset = skb_checksum_start_offset(skb) +
+			 skb->csum_offset + sizeof(__sum16);
+		if (offset > 0)
+			min_len = offset;
+	}
 	return min_len;
 }
 
@@ -3827,12 +3897,6 @@
 	if (unlikely(data_end > data_hard_end))
 		return -EINVAL;
 
-	/* ALL drivers MUST init xdp->frame_sz, chicken check below */
-	if (unlikely(xdp->frame_sz > PAGE_SIZE)) {
-		WARN_ONCE(1, "Too BIG xdp->frame_sz = %d\n", xdp->frame_sz);
-		return -EINVAL;
-	}
-
 	if (unlikely(data_end < xdp->data + ETH_HLEN))
 		return -EINVAL;
 
@@ -3958,37 +4022,75 @@
 }
 EXPORT_SYMBOL_GPL(xdp_master_redirect);
 
-int xdp_do_redirect(struct net_device *dev, struct xdp_buff *xdp,
-		    struct bpf_prog *xdp_prog)
+static inline int __xdp_do_redirect_xsk(struct bpf_redirect_info *ri,
+					struct net_device *dev,
+					struct xdp_buff *xdp,
+					struct bpf_prog *xdp_prog)
 {
-	struct bpf_redirect_info *ri = this_cpu_ptr(&bpf_redirect_info);
 	enum bpf_map_type map_type = ri->map_type;
 	void *fwd = ri->tgt_value;
 	u32 map_id = ri->map_id;
+	int err;
+
+	ri->map_id = 0; /* Valid map id idr range: [1,INT_MAX[ */
+	ri->map_type = BPF_MAP_TYPE_UNSPEC;
+
+	err = __xsk_map_redirect(fwd, xdp);
+	if (unlikely(err))
+		goto err;
+
+	_trace_xdp_redirect_map(dev, xdp_prog, fwd, map_type, map_id, ri->tgt_index);
+	return 0;
+err:
+	_trace_xdp_redirect_map_err(dev, xdp_prog, fwd, map_type, map_id, ri->tgt_index, err);
+	return err;
+}
+
+static __always_inline int __xdp_do_redirect_frame(struct bpf_redirect_info *ri,
+						   struct net_device *dev,
+						   struct xdp_frame *xdpf,
+						   struct bpf_prog *xdp_prog)
+{
+	enum bpf_map_type map_type = ri->map_type;
+	void *fwd = ri->tgt_value;
+	u32 map_id = ri->map_id;
+	u32 flags = ri->flags;
 	struct bpf_map *map;
 	int err;
 
 	ri->map_id = 0; /* Valid map id idr range: [1,INT_MAX[ */
+	ri->flags = 0;
 	ri->map_type = BPF_MAP_TYPE_UNSPEC;
 
+	if (unlikely(!xdpf)) {
+		err = -EOVERFLOW;
+		goto err;
+	}
+
 	switch (map_type) {
 	case BPF_MAP_TYPE_DEVMAP:
 		fallthrough;
 	case BPF_MAP_TYPE_DEVMAP_HASH:
-		map = READ_ONCE(ri->map);
-		if (unlikely(map)) {
+		if (unlikely(flags & BPF_F_BROADCAST)) {
+			map = READ_ONCE(ri->map);
+
+			/* The map pointer is cleared when the map is being torn
+			 * down by bpf_clear_redirect_map()
+			 */
+			if (unlikely(!map)) {
+				err = -ENOENT;
+				break;
+			}
+
 			WRITE_ONCE(ri->map, NULL);
-			err = dev_map_enqueue_multi(xdp, dev, map,
-						    ri->flags & BPF_F_EXCLUDE_INGRESS);
+			err = dev_map_enqueue_multi(xdpf, dev, map,
+						    flags & BPF_F_EXCLUDE_INGRESS);
 		} else {
-			err = dev_map_enqueue(fwd, xdp, dev);
+			err = dev_map_enqueue(fwd, xdpf, dev);
 		}
 		break;
 	case BPF_MAP_TYPE_CPUMAP:
-		err = cpu_map_enqueue(fwd, xdp, dev);
-		break;
-	case BPF_MAP_TYPE_XSKMAP:
-		err = __xsk_map_redirect(fwd, xdp);
+		err = cpu_map_enqueue(fwd, xdpf, dev);
 		break;
 	case BPF_MAP_TYPE_UNSPEC:
 		if (map_id == INT_MAX) {
@@ -3997,7 +4099,7 @@
 				err = -EINVAL;
 				break;
 			}
-			err = dev_xdp_enqueue(fwd, xdp, dev);
+			err = dev_xdp_enqueue(fwd, xdpf, dev);
 			break;
 		}
 		fallthrough;
@@ -4014,14 +4116,40 @@
 	_trace_xdp_redirect_map_err(dev, xdp_prog, fwd, map_type, map_id, ri->tgt_index, err);
 	return err;
 }
+
+int xdp_do_redirect(struct net_device *dev, struct xdp_buff *xdp,
+		    struct bpf_prog *xdp_prog)
+{
+	struct bpf_redirect_info *ri = this_cpu_ptr(&bpf_redirect_info);
+	enum bpf_map_type map_type = ri->map_type;
+
+	if (map_type == BPF_MAP_TYPE_XSKMAP)
+		return __xdp_do_redirect_xsk(ri, dev, xdp, xdp_prog);
+
+	return __xdp_do_redirect_frame(ri, dev, xdp_convert_buff_to_frame(xdp),
+				       xdp_prog);
+}
 EXPORT_SYMBOL_GPL(xdp_do_redirect);
 
+int xdp_do_redirect_frame(struct net_device *dev, struct xdp_buff *xdp,
+			  struct xdp_frame *xdpf, struct bpf_prog *xdp_prog)
+{
+	struct bpf_redirect_info *ri = this_cpu_ptr(&bpf_redirect_info);
+	enum bpf_map_type map_type = ri->map_type;
+
+	if (map_type == BPF_MAP_TYPE_XSKMAP)
+		return __xdp_do_redirect_xsk(ri, dev, xdp, xdp_prog);
+
+	return __xdp_do_redirect_frame(ri, dev, xdpf, xdp_prog);
+}
+EXPORT_SYMBOL_GPL(xdp_do_redirect_frame);
+
 static int xdp_do_generic_redirect_map(struct net_device *dev,
 				       struct sk_buff *skb,
 				       struct xdp_buff *xdp,
-				       struct bpf_prog *xdp_prog,
-				       void *fwd,
-				       enum bpf_map_type map_type, u32 map_id)
+				       struct bpf_prog *xdp_prog, void *fwd,
+				       enum bpf_map_type map_type, u32 map_id,
+				       u32 flags)
 {
 	struct bpf_redirect_info *ri = this_cpu_ptr(&bpf_redirect_info);
 	struct bpf_map *map;
@@ -4031,11 +4159,20 @@
 	case BPF_MAP_TYPE_DEVMAP:
 		fallthrough;
 	case BPF_MAP_TYPE_DEVMAP_HASH:
-		map = READ_ONCE(ri->map);
-		if (unlikely(map)) {
+		if (unlikely(flags & BPF_F_BROADCAST)) {
+			map = READ_ONCE(ri->map);
+
+			/* The map pointer is cleared when the map is being torn
+			 * down by bpf_clear_redirect_map()
+			 */
+			if (unlikely(!map)) {
+				err = -ENOENT;
+				break;
+			}
+
 			WRITE_ONCE(ri->map, NULL);
 			err = dev_map_redirect_multi(dev, skb, xdp_prog, map,
-						     ri->flags & BPF_F_EXCLUDE_INGRESS);
+						     flags & BPF_F_EXCLUDE_INGRESS);
 		} else {
 			err = dev_map_generic_redirect(fwd, skb, xdp_prog);
 		}
@@ -4072,9 +4209,11 @@
 	enum bpf_map_type map_type = ri->map_type;
 	void *fwd = ri->tgt_value;
 	u32 map_id = ri->map_id;
+	u32 flags = ri->flags;
 	int err;
 
 	ri->map_id = 0; /* Valid map id idr range: [1,INT_MAX[ */
+	ri->flags = 0;
 	ri->map_type = BPF_MAP_TYPE_UNSPEC;
 
 	if (map_type == BPF_MAP_TYPE_UNSPEC && map_id == INT_MAX) {
@@ -4094,7 +4233,7 @@
 		return 0;
 	}
 
-	return xdp_do_generic_redirect_map(dev, skb, xdp, xdp_prog, fwd, map_type, map_id);
+	return xdp_do_generic_redirect_map(dev, skb, xdp, xdp_prog, fwd, map_type, map_id, flags);
 err:
 	_trace_xdp_redirect_err(dev, xdp_prog, ri->tgt_index, err);
 	return err;
@@ -4174,7 +4313,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -4188,7 +4327,7 @@
 	.arg1_btf_id	= &bpf_skb_output_btf_ids[0],
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -4371,7 +4510,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 };
@@ -4397,7 +4536,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 };
 
@@ -4567,7 +4706,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -4581,7 +4720,7 @@
 	.arg1_btf_id	= &bpf_xdp_output_btf_ids[0],
 	.arg2_type	= ARG_CONST_MAP_PTR,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE_OR_ZERO,
 };
 
@@ -4741,13 +4880,15 @@
 		/* Only some socketops are supported */
 		switch (optname) {
 		case SO_RCVBUF:
-			val = min_t(u32, val, sysctl_rmem_max);
+			val = min_t(u32, val, READ_ONCE(sysctl_rmem_max));
+			val = min_t(int, val, INT_MAX / 2);
 			sk->sk_userlocks |= SOCK_RCVBUF_LOCK;
 			WRITE_ONCE(sk->sk_rcvbuf,
 				   max_t(int, val * 2, SOCK_MIN_RCVBUF));
 			break;
 		case SO_SNDBUF:
-			val = min_t(u32, val, sysctl_wmem_max);
+			val = min_t(u32, val, READ_ONCE(sysctl_wmem_max));
+			val = min_t(int, val, INT_MAX / 2);
 			sk->sk_userlocks |= SOCK_SNDBUF_LOCK;
 			WRITE_ONCE(sk->sk_sndbuf,
 				   max_t(int, val * 2, SOCK_MIN_SNDBUF));
@@ -4880,7 +5021,7 @@
 				if (val <= 0 || tp->data_segs_out > tp->syn_data)
 					ret = -EINVAL;
 				else
-					tp->snd_cwnd = val;
+					tcp_snd_cwnd_set(tp, val);
 				break;
 			case TCP_BPF_SNDCWND_CLAMP:
 				if (val <= 0) {
@@ -5067,7 +5208,7 @@
 	.arg1_type	= ARG_PTR_TO_BTF_ID_SOCK_COMMON,
 	.arg2_type	= ARG_ANYTHING,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE,
 };
 
@@ -5101,7 +5242,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE,
 };
 
@@ -5135,7 +5276,7 @@
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
 	.arg3_type	= ARG_ANYTHING,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE,
 };
 
@@ -5310,7 +5451,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 };
 
@@ -5361,12 +5502,8 @@
 #endif
 
 #if IS_ENABLED(CONFIG_INET) || IS_ENABLED(CONFIG_IPV6)
-static int bpf_fib_set_fwd_params(struct bpf_fib_lookup *params,
-				  const struct neighbour *neigh,
-				  const struct net_device *dev, u32 mtu)
+static int bpf_fib_set_fwd_params(struct bpf_fib_lookup *params, u32 mtu)
 {
-	memcpy(params->dmac, neigh->ha, ETH_ALEN);
-	memcpy(params->smac, dev->dev_addr, ETH_ALEN);
 	params->h_vlan_TCI = 0;
 	params->h_vlan_proto = 0;
 	if (mtu)
@@ -5420,6 +5557,12 @@
 		u32 tbid = l3mdev_fib_table_rcu(dev) ? : RT_TABLE_MAIN;
 		struct fib_table *tb;
 
+		if (flags & BPF_FIB_LOOKUP_TBID) {
+			tbid = params->tbid;
+			/* zero out for vlan output */
+			params->tbid = 0;
+		}
+
 		tb = fib_get_table(net, tbid);
 		if (unlikely(!tb))
 			return BPF_FIB_LKUP_RET_NOT_FWDED;
@@ -5471,27 +5614,38 @@
 	params->rt_metric = res.fi->fib_priority;
 	params->ifindex = dev->ifindex;
 
+	if (flags & BPF_FIB_LOOKUP_SRC)
+		params->ipv4_src = fib_result_prefsrc(net, &res);
+
 	/* xdp and cls_bpf programs are run in RCU-bh so
 	 * rcu_read_lock_bh is not needed here
 	 */
 	if (likely(nhc->nhc_gw_family != AF_INET6)) {
 		if (nhc->nhc_gw_family)
 			params->ipv4_dst = nhc->nhc_gw.ipv4;
-
-		neigh = __ipv4_neigh_lookup_noref(dev,
-						 (__force u32)params->ipv4_dst);
 	} else {
 		struct in6_addr *dst = (struct in6_addr *)params->ipv6_dst;
 
 		params->family = AF_INET6;
 		*dst = nhc->nhc_gw.ipv6;
-		neigh = __ipv6_neigh_lookup_noref_stub(dev, dst);
 	}
 
-	if (!neigh)
+	if (flags & BPF_FIB_LOOKUP_SKIP_NEIGH)
+		goto set_fwd_params;
+
+	if (likely(nhc->nhc_gw_family != AF_INET6))
+		neigh = __ipv4_neigh_lookup_noref(dev,
+						  (__force u32)params->ipv4_dst);
+	else
+		neigh = __ipv6_neigh_lookup_noref_stub(dev, params->ipv6_dst);
+
+	if (!neigh || !(neigh->nud_state & NUD_VALID))
 		return BPF_FIB_LKUP_RET_NO_NEIGH;
+	memcpy(params->dmac, neigh->ha, ETH_ALEN);
+	memcpy(params->smac, dev->dev_addr, ETH_ALEN);
 
-	return bpf_fib_set_fwd_params(params, neigh, dev, mtu);
+set_fwd_params:
+	return bpf_fib_set_fwd_params(params, mtu);
 }
 #endif
 
@@ -5545,6 +5699,12 @@
 		u32 tbid = l3mdev_fib_table_rcu(dev) ? : RT_TABLE_MAIN;
 		struct fib6_table *tb;
 
+		if (flags & BPF_FIB_LOOKUP_TBID) {
+			tbid = params->tbid;
+			/* zero out for vlan output */
+			params->tbid = 0;
+		}
+
 		tb = ipv6_stub->fib6_get_table(net, tbid);
 		if (unlikely(!tb))
 			return BPF_FIB_LKUP_RET_NOT_FWDED;
@@ -5599,24 +5759,46 @@
 	params->rt_metric = res.f6i->fib6_metric;
 	params->ifindex = dev->ifindex;
 
+	if (flags & BPF_FIB_LOOKUP_SRC) {
+		if (res.f6i->fib6_prefsrc.plen) {
+			*src = res.f6i->fib6_prefsrc.addr;
+		} else {
+			err = ipv6_bpf_stub->ipv6_dev_get_saddr(net, dev,
+								&fl6.daddr, 0,
+								src);
+			if (err)
+				return BPF_FIB_LKUP_RET_NO_SRC_ADDR;
+		}
+	}
+
+	if (flags & BPF_FIB_LOOKUP_SKIP_NEIGH)
+		goto set_fwd_params;
+
 	/* xdp and cls_bpf programs are run in RCU-bh so rcu_read_lock_bh is
 	 * not needed here.
 	 */
 	neigh = __ipv6_neigh_lookup_noref_stub(dev, dst);
-	if (!neigh)
+	if (!neigh || !(neigh->nud_state & NUD_VALID))
 		return BPF_FIB_LKUP_RET_NO_NEIGH;
+	memcpy(params->dmac, neigh->ha, ETH_ALEN);
+	memcpy(params->smac, dev->dev_addr, ETH_ALEN);
 
-	return bpf_fib_set_fwd_params(params, neigh, dev, mtu);
+set_fwd_params:
+	return bpf_fib_set_fwd_params(params, mtu);
 }
 #endif
 
+#define BPF_FIB_LOOKUP_MASK (BPF_FIB_LOOKUP_DIRECT | BPF_FIB_LOOKUP_OUTPUT | \
+			     BPF_FIB_LOOKUP_SKIP_NEIGH | BPF_FIB_LOOKUP_TBID | \
+			     BPF_FIB_LOOKUP_SRC)
+
 BPF_CALL_4(bpf_xdp_fib_lookup, struct xdp_buff *, ctx,
 	   struct bpf_fib_lookup *, params, int, plen, u32, flags)
 {
 	if (plen < sizeof(*params))
 		return -EINVAL;
 
-	if (flags & ~(BPF_FIB_LOOKUP_DIRECT | BPF_FIB_LOOKUP_OUTPUT))
+	if (flags & ~BPF_FIB_LOOKUP_MASK)
 		return -EINVAL;
 
 	switch (params->family) {
@@ -5654,7 +5836,7 @@
 	if (plen < sizeof(*params))
 		return -EINVAL;
 
-	if (flags & ~(BPF_FIB_LOOKUP_DIRECT | BPF_FIB_LOOKUP_OUTPUT))
+	if (flags & ~BPF_FIB_LOOKUP_MASK)
 		return -EINVAL;
 
 	if (params->tot_len)
@@ -5846,7 +6028,6 @@
 	if (err)
 		return err;
 
-	ipv6_hdr(skb)->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
 	skb_set_transport_header(skb, sizeof(struct ipv6hdr));
 
 	return seg6_lookup_nexthop(skb, NULL, 0);
@@ -5898,7 +6079,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
-	.arg3_type	= ARG_PTR_TO_MEM,
+	.arg3_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE
 };
 
@@ -5908,7 +6089,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
-	.arg3_type	= ARG_PTR_TO_MEM,
+	.arg3_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE
 };
 
@@ -5951,7 +6132,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
-	.arg3_type	= ARG_PTR_TO_MEM,
+	.arg3_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE
 };
 
@@ -6039,7 +6220,7 @@
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
 	.arg2_type	= ARG_ANYTHING,
-	.arg3_type	= ARG_PTR_TO_MEM,
+	.arg3_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg4_type	= ARG_CONST_SIZE
 };
 
@@ -6157,12 +6338,11 @@
 static struct sock *
 __bpf_skc_lookup(struct sk_buff *skb, struct bpf_sock_tuple *tuple, u32 len,
 		 struct net *caller_net, u32 ifindex, u8 proto, u64 netns_id,
-		 u64 flags)
+		 u64 flags, int sdif)
 {
 	struct sock *sk = NULL;
-	u8 family = AF_UNSPEC;
 	struct net *net;
-	int sdif;
+	u8 family;
 
 	if (len == sizeof(tuple->ipv4))
 		family = AF_INET;
@@ -6171,14 +6351,15 @@
 	else
 		return NULL;
 
-	if (unlikely(family == AF_UNSPEC || flags ||
-		     !((s32)netns_id < 0 || netns_id <= S32_MAX)))
+	if (unlikely(flags || !((s32)netns_id < 0 || netns_id <= S32_MAX)))
 		goto out;
 
-	if (family == AF_INET)
-		sdif = inet_sdif(skb);
-	else
-		sdif = inet6_sdif(skb);
+	if (sdif < 0) {
+		if (family == AF_INET)
+			sdif = inet_sdif(skb);
+		else
+			sdif = inet6_sdif(skb);
+	}
 
 	if ((s32)netns_id < 0) {
 		net = caller_net;
@@ -6198,16 +6379,28 @@
 static struct sock *
 __bpf_sk_lookup(struct sk_buff *skb, struct bpf_sock_tuple *tuple, u32 len,
 		struct net *caller_net, u32 ifindex, u8 proto, u64 netns_id,
-		u64 flags)
+		u64 flags, int sdif)
 {
 	struct sock *sk = __bpf_skc_lookup(skb, tuple, len, caller_net,
-					   ifindex, proto, netns_id, flags);
+					   ifindex, proto, netns_id, flags,
+					   sdif);
 
 	if (sk) {
-		sk = sk_to_full_sk(sk);
-		if (!sk_fullsock(sk)) {
+		struct sock *sk2 = sk_to_full_sk(sk);
+
+		/* sk_to_full_sk() may return (sk)->rsk_listener, so make sure the original sk
+		 * sock refcnt is decremented to prevent a request_sock leak.
+		 */
+		if (!sk_fullsock(sk2))
+			sk2 = NULL;
+		if (sk2 != sk) {
 			sock_gen_put(sk);
-			return NULL;
+			/* Ensure there is no need to bump sk2 refcnt */
+			if (unlikely(sk2 && !sock_flag(sk2, SOCK_RCU_FREE))) {
+				WARN_ONCE(1, "Found non-RCU, unreferenced socket!");
+				return NULL;
+			}
+			sk = sk2;
 		}
 	}
 
@@ -6230,7 +6423,7 @@
 	}
 
 	return __bpf_skc_lookup(skb, tuple, len, caller_net, ifindex, proto,
-				netns_id, flags);
+				netns_id, flags, -1);
 }
 
 static struct sock *
@@ -6241,10 +6434,21 @@
 					 flags);
 
 	if (sk) {
-		sk = sk_to_full_sk(sk);
-		if (!sk_fullsock(sk)) {
+		struct sock *sk2 = sk_to_full_sk(sk);
+
+		/* sk_to_full_sk() may return (sk)->rsk_listener, so make sure the original sk
+		 * sock refcnt is decremented to prevent a request_sock leak.
+		 */
+		if (!sk_fullsock(sk2))
+			sk2 = NULL;
+		if (sk2 != sk) {
 			sock_gen_put(sk);
-			return NULL;
+			/* Ensure there is no need to bump sk2 refcnt */
+			if (unlikely(sk2 && !sock_flag(sk2, SOCK_RCU_FREE))) {
+				WARN_ONCE(1, "Found non-RCU, unreferenced socket!");
+				return NULL;
+			}
+			sk = sk2;
 		}
 	}
 
@@ -6264,7 +6468,7 @@
 	.pkt_access	= true,
 	.ret_type	= RET_PTR_TO_SOCK_COMMON_OR_NULL,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 	.arg5_type	= ARG_ANYTHING,
@@ -6283,7 +6487,7 @@
 	.pkt_access	= true,
 	.ret_type	= RET_PTR_TO_SOCKET_OR_NULL,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 	.arg5_type	= ARG_ANYTHING,
@@ -6302,7 +6506,79 @@
 	.pkt_access	= true,
 	.ret_type	= RET_PTR_TO_SOCKET_OR_NULL,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
+	.arg3_type	= ARG_CONST_SIZE,
+	.arg4_type	= ARG_ANYTHING,
+	.arg5_type	= ARG_ANYTHING,
+};
+
+BPF_CALL_5(bpf_tc_skc_lookup_tcp, struct sk_buff *, skb,
+	   struct bpf_sock_tuple *, tuple, u32, len, u64, netns_id, u64, flags)
+{
+	struct net_device *dev = skb->dev;
+	int ifindex = dev->ifindex, sdif = dev_sdif(dev);
+	struct net *caller_net = dev_net(dev);
+
+	return (unsigned long)__bpf_skc_lookup(skb, tuple, len, caller_net,
+					       ifindex, IPPROTO_TCP, netns_id,
+					       flags, sdif);
+}
+
+static const struct bpf_func_proto bpf_tc_skc_lookup_tcp_proto = {
+	.func		= bpf_tc_skc_lookup_tcp,
+	.gpl_only	= false,
+	.pkt_access	= true,
+	.ret_type	= RET_PTR_TO_SOCK_COMMON_OR_NULL,
+	.arg1_type	= ARG_PTR_TO_CTX,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
+	.arg3_type	= ARG_CONST_SIZE,
+	.arg4_type	= ARG_ANYTHING,
+	.arg5_type	= ARG_ANYTHING,
+};
+
+BPF_CALL_5(bpf_tc_sk_lookup_tcp, struct sk_buff *, skb,
+	   struct bpf_sock_tuple *, tuple, u32, len, u64, netns_id, u64, flags)
+{
+	struct net_device *dev = skb->dev;
+	int ifindex = dev->ifindex, sdif = dev_sdif(dev);
+	struct net *caller_net = dev_net(dev);
+
+	return (unsigned long)__bpf_sk_lookup(skb, tuple, len, caller_net,
+					      ifindex, IPPROTO_TCP, netns_id,
+					      flags, sdif);
+}
+
+static const struct bpf_func_proto bpf_tc_sk_lookup_tcp_proto = {
+	.func		= bpf_tc_sk_lookup_tcp,
+	.gpl_only	= false,
+	.pkt_access	= true,
+	.ret_type	= RET_PTR_TO_SOCKET_OR_NULL,
+	.arg1_type	= ARG_PTR_TO_CTX,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
+	.arg3_type	= ARG_CONST_SIZE,
+	.arg4_type	= ARG_ANYTHING,
+	.arg5_type	= ARG_ANYTHING,
+};
+
+BPF_CALL_5(bpf_tc_sk_lookup_udp, struct sk_buff *, skb,
+	   struct bpf_sock_tuple *, tuple, u32, len, u64, netns_id, u64, flags)
+{
+	struct net_device *dev = skb->dev;
+	int ifindex = dev->ifindex, sdif = dev_sdif(dev);
+	struct net *caller_net = dev_net(dev);
+
+	return (unsigned long)__bpf_sk_lookup(skb, tuple, len, caller_net,
+					      ifindex, IPPROTO_UDP, netns_id,
+					      flags, sdif);
+}
+
+static const struct bpf_func_proto bpf_tc_sk_lookup_udp_proto = {
+	.func		= bpf_tc_sk_lookup_udp,
+	.gpl_only	= false,
+	.pkt_access	= true,
+	.ret_type	= RET_PTR_TO_SOCKET_OR_NULL,
+	.arg1_type	= ARG_PTR_TO_CTX,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 	.arg5_type	= ARG_ANYTHING,
@@ -6325,12 +6601,13 @@
 BPF_CALL_5(bpf_xdp_sk_lookup_udp, struct xdp_buff *, ctx,
 	   struct bpf_sock_tuple *, tuple, u32, len, u32, netns_id, u64, flags)
 {
-	struct net *caller_net = dev_net(ctx->rxq->dev);
-	int ifindex = ctx->rxq->dev->ifindex;
+	struct net_device *dev = ctx->rxq->dev;
+	int ifindex = dev->ifindex, sdif = dev_sdif(dev);
+	struct net *caller_net = dev_net(dev);
 
 	return (unsigned long)__bpf_sk_lookup(NULL, tuple, len, caller_net,
 					      ifindex, IPPROTO_UDP, netns_id,
-					      flags);
+					      flags, sdif);
 }
 
 static const struct bpf_func_proto bpf_xdp_sk_lookup_udp_proto = {
@@ -6339,7 +6616,7 @@
 	.pkt_access     = true,
 	.ret_type       = RET_PTR_TO_SOCKET_OR_NULL,
 	.arg1_type      = ARG_PTR_TO_CTX,
-	.arg2_type      = ARG_PTR_TO_MEM,
+	.arg2_type      = ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type      = ARG_CONST_SIZE,
 	.arg4_type      = ARG_ANYTHING,
 	.arg5_type      = ARG_ANYTHING,
@@ -6348,12 +6625,13 @@
 BPF_CALL_5(bpf_xdp_skc_lookup_tcp, struct xdp_buff *, ctx,
 	   struct bpf_sock_tuple *, tuple, u32, len, u32, netns_id, u64, flags)
 {
-	struct net *caller_net = dev_net(ctx->rxq->dev);
-	int ifindex = ctx->rxq->dev->ifindex;
+	struct net_device *dev = ctx->rxq->dev;
+	int ifindex = dev->ifindex, sdif = dev_sdif(dev);
+	struct net *caller_net = dev_net(dev);
 
 	return (unsigned long)__bpf_skc_lookup(NULL, tuple, len, caller_net,
 					       ifindex, IPPROTO_TCP, netns_id,
-					       flags);
+					       flags, sdif);
 }
 
 static const struct bpf_func_proto bpf_xdp_skc_lookup_tcp_proto = {
@@ -6362,7 +6640,7 @@
 	.pkt_access     = true,
 	.ret_type       = RET_PTR_TO_SOCK_COMMON_OR_NULL,
 	.arg1_type      = ARG_PTR_TO_CTX,
-	.arg2_type      = ARG_PTR_TO_MEM,
+	.arg2_type      = ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type      = ARG_CONST_SIZE,
 	.arg4_type      = ARG_ANYTHING,
 	.arg5_type      = ARG_ANYTHING,
@@ -6371,12 +6649,13 @@
 BPF_CALL_5(bpf_xdp_sk_lookup_tcp, struct xdp_buff *, ctx,
 	   struct bpf_sock_tuple *, tuple, u32, len, u32, netns_id, u64, flags)
 {
-	struct net *caller_net = dev_net(ctx->rxq->dev);
-	int ifindex = ctx->rxq->dev->ifindex;
+	struct net_device *dev = ctx->rxq->dev;
+	int ifindex = dev->ifindex, sdif = dev_sdif(dev);
+	struct net *caller_net = dev_net(dev);
 
 	return (unsigned long)__bpf_sk_lookup(NULL, tuple, len, caller_net,
 					      ifindex, IPPROTO_TCP, netns_id,
-					      flags);
+					      flags, sdif);
 }
 
 static const struct bpf_func_proto bpf_xdp_sk_lookup_tcp_proto = {
@@ -6385,7 +6664,7 @@
 	.pkt_access     = true,
 	.ret_type       = RET_PTR_TO_SOCKET_OR_NULL,
 	.arg1_type      = ARG_PTR_TO_CTX,
-	.arg2_type      = ARG_PTR_TO_MEM,
+	.arg2_type      = ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type      = ARG_CONST_SIZE,
 	.arg4_type      = ARG_ANYTHING,
 	.arg5_type      = ARG_ANYTHING,
@@ -6396,7 +6675,8 @@
 {
 	return (unsigned long)__bpf_skc_lookup(NULL, tuple, len,
 					       sock_net(ctx->sk), 0,
-					       IPPROTO_TCP, netns_id, flags);
+					       IPPROTO_TCP, netns_id, flags,
+					       -1);
 }
 
 static const struct bpf_func_proto bpf_sock_addr_skc_lookup_tcp_proto = {
@@ -6404,7 +6684,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_PTR_TO_SOCK_COMMON_OR_NULL,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 	.arg5_type	= ARG_ANYTHING,
@@ -6415,7 +6695,7 @@
 {
 	return (unsigned long)__bpf_sk_lookup(NULL, tuple, len,
 					      sock_net(ctx->sk), 0, IPPROTO_TCP,
-					      netns_id, flags);
+					      netns_id, flags, -1);
 }
 
 static const struct bpf_func_proto bpf_sock_addr_sk_lookup_tcp_proto = {
@@ -6423,7 +6703,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_PTR_TO_SOCKET_OR_NULL,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 	.arg5_type	= ARG_ANYTHING,
@@ -6434,7 +6714,7 @@
 {
 	return (unsigned long)__bpf_sk_lookup(NULL, tuple, len,
 					      sock_net(ctx->sk), 0, IPPROTO_UDP,
-					      netns_id, flags);
+					      netns_id, flags, -1);
 }
 
 static const struct bpf_func_proto bpf_sock_addr_sk_lookup_udp_proto = {
@@ -6442,7 +6722,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_PTR_TO_SOCKET_OR_NULL,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 	.arg5_type	= ARG_ANYTHING,
@@ -6708,30 +6988,39 @@
 	if (sk->sk_protocol != IPPROTO_TCP || sk->sk_state != TCP_LISTEN)
 		return -EINVAL;
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_syncookies)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_syncookies))
 		return -EINVAL;
 
 	if (!th->ack || th->rst || th->syn)
 		return -ENOENT;
 
+	if (unlikely(iph_len < sizeof(struct iphdr)))
+		return -EINVAL;
+
 	if (tcp_synq_no_recent_overflow(sk))
 		return -ENOENT;
 
 	cookie = ntohl(th->ack_seq) - 1;
 
-	switch (sk->sk_family) {
-	case AF_INET:
-		if (unlikely(iph_len < sizeof(struct iphdr)))
+	/* Both struct iphdr and struct ipv6hdr have the version field at the
+	 * same offset so we can cast to the shorter header (struct iphdr).
+	 */
+	switch (((struct iphdr *)iph)->version) {
+	case 4:
+		if (sk->sk_family == AF_INET6 && ipv6_only_sock(sk))
 			return -EINVAL;
 
 		ret = __cookie_v4_check((struct iphdr *)iph, th, cookie);
 		break;
 
 #if IS_BUILTIN(CONFIG_IPV6)
-	case AF_INET6:
+	case 6:
 		if (unlikely(iph_len < sizeof(struct ipv6hdr)))
 			return -EINVAL;
 
+		if (sk->sk_family != AF_INET6)
+			return -EINVAL;
+
 		ret = __cookie_v6_check((struct ipv6hdr *)iph, th, cookie);
 		break;
 #endif /* CONFIG_IPV6 */
@@ -6755,9 +7044,9 @@
 	.pkt_access	= true,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_BTF_ID_SOCK_COMMON,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE,
 };
 
@@ -6774,7 +7063,7 @@
 	if (sk->sk_protocol != IPPROTO_TCP || sk->sk_state != TCP_LISTEN)
 		return -EINVAL;
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_syncookies)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_syncookies))
 		return -ENOENT;
 
 	if (!th->syn || th->ack || th->fin || th->rst)
@@ -6824,9 +7113,9 @@
 	.pkt_access	= true,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_BTF_ID_SOCK_COMMON,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
-	.arg4_type	= ARG_PTR_TO_MEM,
+	.arg4_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg5_type	= ARG_CONST_SIZE,
 };
 
@@ -6840,6 +7129,8 @@
 		return -ENETUNREACH;
 	if (unlikely(sk_fullsock(sk) && sk->sk_reuseport))
 		return -ESOCKTNOSUPPORT;
+	if (sk_unhashed(sk))
+		return -EOPNOTSUPP;
 	if (sk_is_refcounted(sk) &&
 	    unlikely(!refcount_inc_not_zero(&sk->sk_refcnt)))
 		return -ENOENT;
@@ -7055,7 +7346,7 @@
 	.gpl_only	= false,
 	.ret_type	= RET_INTEGER,
 	.arg1_type	= ARG_PTR_TO_CTX,
-	.arg2_type	= ARG_PTR_TO_MEM,
+	.arg2_type	= ARG_PTR_TO_MEM | MEM_RDONLY,
 	.arg3_type	= ARG_CONST_SIZE,
 	.arg4_type	= ARG_ANYTHING,
 };
@@ -7162,6 +7453,8 @@
 #endif
 	case BPF_FUNC_sk_storage_get:
 		return &bpf_sk_storage_get_cg_sock_proto;
+	case BPF_FUNC_ktime_get_coarse_ns:
+		return &bpf_ktime_get_coarse_ns_proto;
 	default:
 		return bpf_base_func_proto(func_id);
 	}
@@ -7426,9 +7719,9 @@
 #endif
 #ifdef CONFIG_INET
 	case BPF_FUNC_sk_lookup_tcp:
-		return &bpf_sk_lookup_tcp_proto;
+		return &bpf_tc_sk_lookup_tcp_proto;
 	case BPF_FUNC_sk_lookup_udp:
-		return &bpf_sk_lookup_udp_proto;
+		return &bpf_tc_sk_lookup_udp_proto;
 	case BPF_FUNC_sk_release:
 		return &bpf_sk_release_proto;
 	case BPF_FUNC_tcp_sock:
@@ -7436,7 +7729,7 @@
 	case BPF_FUNC_get_listener_sock:
 		return &bpf_get_listener_sock_proto;
 	case BPF_FUNC_skc_lookup_tcp:
-		return &bpf_skc_lookup_tcp_proto;
+		return &bpf_tc_skc_lookup_tcp_proto;
 	case BPF_FUNC_tcp_check_syncookie:
 		return &bpf_tcp_check_syncookie_proto;
 	case BPF_FUNC_skb_ecn_set_ce:
@@ -7959,6 +8252,7 @@
 			      struct bpf_insn_access_aux *info)
 {
 	const int size_default = sizeof(__u32);
+	int field_size;
 
 	if (off < 0 || off >= sizeof(struct bpf_sock))
 		return false;
@@ -7970,7 +8264,6 @@
 	case offsetof(struct bpf_sock, family):
 	case offsetof(struct bpf_sock, type):
 	case offsetof(struct bpf_sock, protocol):
-	case offsetof(struct bpf_sock, dst_port):
 	case offsetof(struct bpf_sock, src_port):
 	case offsetof(struct bpf_sock, rx_queue_mapping):
 	case bpf_ctx_range(struct bpf_sock, src_ip4):
@@ -7979,6 +8272,14 @@
 	case bpf_ctx_range_till(struct bpf_sock, dst_ip6[0], dst_ip6[3]):
 		bpf_ctx_record_field_size(info, size_default);
 		return bpf_ctx_narrow_access_ok(off, size, size_default);
+	case bpf_ctx_range(struct bpf_sock, dst_port):
+		field_size = size == size_default ?
+			size_default : sizeof_field(struct bpf_sock, dst_port);
+		bpf_ctx_record_field_size(info, field_size);
+		return bpf_ctx_narrow_access_ok(off, size, field_size);
+	case offsetofend(struct bpf_sock, dst_port) ...
+	     offsetof(struct bpf_sock, dst_ip4) - 1:
+		return false;
 	}
 
 	return size == size_default;
@@ -8174,9 +8475,9 @@
 {
 	const u32 act_max = XDP_REDIRECT;
 
-	WARN_ONCE(1, "%s XDP return value %u, expect packet loss!\n",
-		  act > act_max ? "Illegal" : "Driver unsupported",
-		  act);
+	pr_warn_once("%s XDP return value %u, expect packet loss!\n",
+		     act > act_max ? "Illegal" : "Driver unsupported",
+		     act);
 }
 EXPORT_SYMBOL_GPL(bpf_warn_invalid_xdp_action);
 
@@ -9735,22 +10036,46 @@
 static struct bpf_insn *bpf_convert_data_end_access(const struct bpf_insn *si,
 						    struct bpf_insn *insn)
 {
-	/* si->dst_reg = skb->data */
+	int reg;
+	int temp_reg_off = offsetof(struct sk_buff, cb) +
+			   offsetof(struct sk_skb_cb, temp_reg);
+
+	if (si->src_reg == si->dst_reg) {
+		/* We need an extra register, choose and save a register. */
+		reg = BPF_REG_9;
+		if (si->src_reg == reg || si->dst_reg == reg)
+			reg--;
+		if (si->src_reg == reg || si->dst_reg == reg)
+			reg--;
+		*insn++ = BPF_STX_MEM(BPF_DW, si->src_reg, reg, temp_reg_off);
+	} else {
+		reg = si->dst_reg;
+	}
+
+	/* reg = skb->data */
 	*insn++ = BPF_LDX_MEM(BPF_FIELD_SIZEOF(struct sk_buff, data),
-			      si->dst_reg, si->src_reg,
+			      reg, si->src_reg,
 			      offsetof(struct sk_buff, data));
 	/* AX = skb->len */
 	*insn++ = BPF_LDX_MEM(BPF_FIELD_SIZEOF(struct sk_buff, len),
 			      BPF_REG_AX, si->src_reg,
 			      offsetof(struct sk_buff, len));
-	/* si->dst_reg = skb->data + skb->len */
-	*insn++ = BPF_ALU64_REG(BPF_ADD, si->dst_reg, BPF_REG_AX);
+	/* reg = skb->data + skb->len */
+	*insn++ = BPF_ALU64_REG(BPF_ADD, reg, BPF_REG_AX);
 	/* AX = skb->data_len */
 	*insn++ = BPF_LDX_MEM(BPF_FIELD_SIZEOF(struct sk_buff, data_len),
 			      BPF_REG_AX, si->src_reg,
 			      offsetof(struct sk_buff, data_len));
-	/* si->dst_reg = skb->data + skb->len - skb->data_len */
-	*insn++ = BPF_ALU64_REG(BPF_SUB, si->dst_reg, BPF_REG_AX);
+
+	/* reg = skb->data + skb->len - skb->data_len */
+	*insn++ = BPF_ALU64_REG(BPF_SUB, reg, BPF_REG_AX);
+
+	if (si->src_reg == si->dst_reg) {
+		/* Restore the saved register */
+		*insn++ = BPF_MOV64_REG(BPF_REG_AX, si->src_reg);
+		*insn++ = BPF_MOV64_REG(si->dst_reg, reg);
+		*insn++ = BPF_LDX_MEM(BPF_DW, reg, BPF_REG_AX, temp_reg_off);
+	}
 
 	return insn;
 }
@@ -9761,11 +10086,33 @@
 				     struct bpf_prog *prog, u32 *target_size)
 {
 	struct bpf_insn *insn = insn_buf;
+	int off;
 
 	switch (si->off) {
 	case offsetof(struct __sk_buff, data_end):
 		insn = bpf_convert_data_end_access(si, insn);
 		break;
+	case offsetof(struct __sk_buff, cb[0]) ...
+	     offsetofend(struct __sk_buff, cb[4]) - 1:
+		BUILD_BUG_ON(sizeof_field(struct sk_skb_cb, data) < 20);
+		BUILD_BUG_ON((offsetof(struct sk_buff, cb) +
+			      offsetof(struct sk_skb_cb, data)) %
+			     sizeof(__u64));
+
+		prog->cb_access = 1;
+		off  = si->off;
+		off -= offsetof(struct __sk_buff, cb[0]);
+		off += offsetof(struct sk_buff, cb);
+		off += offsetof(struct sk_skb_cb, data);
+		if (type == BPF_WRITE)
+			*insn++ = BPF_STX_MEM(BPF_SIZE(si->code), si->dst_reg,
+					      si->src_reg, off);
+		else
+			*insn++ = BPF_LDX_MEM(BPF_SIZE(si->code), si->dst_reg,
+					      si->src_reg, off);
+		break;
+
+
 	default:
 		return bpf_convert_ctx_access(type, si, insn_buf, prog,
 					      target_size);
@@ -10079,8 +10426,7 @@
 }
 EXPORT_SYMBOL_GPL(sk_detach_filter);
 
-int sk_get_filter(struct sock *sk, struct sock_filter __user *ubuf,
-		  unsigned int len)
+int sk_get_filter(struct sock *sk, sockptr_t optval, unsigned int len)
 {
 	struct sock_fprog_kern *fprog;
 	struct sk_filter *filter;
@@ -10111,7 +10457,7 @@
 		goto out;
 
 	ret = -EFAULT;
-	if (copy_to_user(ubuf, fprog->filter, bpf_classic_proglen(fprog)))
+	if (copy_to_sockptr(optval, fprog->filter, bpf_classic_proglen(fprog)))
 		goto out;
 
 	/* Instead of bytes, the API requests to return the number
@@ -10163,6 +10509,7 @@
 	bool is_sockarray = map->map_type == BPF_MAP_TYPE_REUSEPORT_SOCKARRAY;
 	struct sock_reuseport *reuse;
 	struct sock *selected_sk;
+	int err;
 
 	selected_sk = map->ops->map_lookup_elem(map, key);
 	if (!selected_sk)
@@ -10170,10 +10517,6 @@
 
 	reuse = rcu_dereference(selected_sk->sk_reuseport_cb);
 	if (!reuse) {
-		/* Lookup in sock_map can return TCP ESTABLISHED sockets. */
-		if (sk_is_refcounted(selected_sk))
-			sock_put(selected_sk);
-
 		/* reuseport_array has only sk with non NULL sk_reuseport_cb.
 		 * The only (!reuse) case here is - the sk has already been
 		 * unhashed (e.g. by close()), so treat it as -ENOENT.
@@ -10181,24 +10524,33 @@
 		 * Other maps (e.g. sock_map) do not provide this guarantee and
 		 * the sk may never be in the reuseport group to begin with.
 		 */
-		return is_sockarray ? -ENOENT : -EINVAL;
+		err = is_sockarray ? -ENOENT : -EINVAL;
+		goto error;
 	}
 
 	if (unlikely(reuse->reuseport_id != reuse_kern->reuseport_id)) {
 		struct sock *sk = reuse_kern->sk;
 
-		if (sk->sk_protocol != selected_sk->sk_protocol)
-			return -EPROTOTYPE;
-		else if (sk->sk_family != selected_sk->sk_family)
-			return -EAFNOSUPPORT;
-
-		/* Catch all. Likely bound to a different sockaddr. */
-		return -EBADFD;
+		if (sk->sk_protocol != selected_sk->sk_protocol) {
+			err = -EPROTOTYPE;
+		} else if (sk->sk_family != selected_sk->sk_family) {
+			err = -EAFNOSUPPORT;
+		} else {
+			/* Catch all. Likely bound to a different sockaddr. */
+			err = -EBADFD;
+		}
+		goto error;
 	}
 
 	reuse_kern->selected_sk = selected_sk;
 
 	return 0;
+error:
+	/* Lookup in sock_map can return TCP ESTABLISHED sockets. */
+	if (sk_is_refcounted(selected_sk))
+		sock_put(selected_sk);
+
+	return err;
 }
 
 static const struct bpf_func_proto sk_select_reuseport_proto = {
@@ -10260,6 +10612,8 @@
 		return &sk_reuseport_load_bytes_relative_proto;
 	case BPF_FUNC_get_socket_cookie:
 		return &bpf_get_socket_ptr_cookie_proto;
+	case BPF_FUNC_ktime_get_coarse_ns:
+		return &bpf_ktime_get_coarse_ns_proto;
 	default:
 		return bpf_base_func_proto(func_id);
 	}
@@ -10468,7 +10822,8 @@
 	case bpf_ctx_range(struct bpf_sk_lookup, local_ip4):
 	case bpf_ctx_range_till(struct bpf_sk_lookup, remote_ip6[0], remote_ip6[3]):
 	case bpf_ctx_range_till(struct bpf_sk_lookup, local_ip6[0], local_ip6[3]):
-	case bpf_ctx_range(struct bpf_sk_lookup, remote_port):
+	case offsetof(struct bpf_sk_lookup, remote_port) ...
+	     offsetof(struct bpf_sk_lookup, local_ip4) - 1:
 	case bpf_ctx_range(struct bpf_sk_lookup, local_port):
 		bpf_ctx_record_field_size(info, sizeof(__u32));
 		return bpf_ctx_narrow_access_ok(off, size, sizeof(__u32));
@@ -10741,6 +11096,8 @@
 	case BPF_FUNC_skc_to_udp6_sock:
 		func = &bpf_skc_to_udp6_sock_proto;
 		break;
+	case BPF_FUNC_ktime_get_coarse_ns:
+		return &bpf_ktime_get_coarse_ns_proto;
 	default:
 		return bpf_base_func_proto(func_id);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/flow_dissector.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/flow_dissector.c
@@ -238,7 +238,7 @@
 skb_flow_dissect_ct(const struct sk_buff *skb,
 		    struct flow_dissector *flow_dissector,
 		    void *target_container, u16 *ctinfo_map,
-		    size_t mapsize, bool post_ct)
+		    size_t mapsize, bool post_ct, u16 zone)
 {
 #if IS_ENABLED(CONFIG_NF_CONNTRACK)
 	struct flow_dissector_key_ct *key;
@@ -260,6 +260,7 @@
 	if (!ct) {
 		key->ct_state = TCA_FLOWER_KEY_CT_FLAGS_TRACKED |
 				TCA_FLOWER_KEY_CT_FLAGS_INVALID;
+		key->ct_zone = zone;
 		return;
 	}
 
@@ -269,7 +270,7 @@
 	key->ct_zone = ct->zone.id;
 #endif
 #if IS_ENABLED(CONFIG_NF_CONNTRACK_MARK)
-	key->ct_mark = ct->mark;
+	key->ct_mark = READ_ONCE(ct->mark);
 #endif
 
 	cl = nf_ct_labels_find(ct);
@@ -724,23 +725,30 @@
 			 void *target_container, const void *data,
 			 int nhoff, u8 ip_proto, int hlen)
 {
-	enum flow_dissector_key_id dissector_ports = FLOW_DISSECTOR_KEY_MAX;
-	struct flow_dissector_key_ports *key_ports;
+	struct flow_dissector_key_ports_range *key_ports_range = NULL;
+	struct flow_dissector_key_ports *key_ports = NULL;
+	__be32 ports;
 
 	if (dissector_uses_key(flow_dissector, FLOW_DISSECTOR_KEY_PORTS))
-		dissector_ports = FLOW_DISSECTOR_KEY_PORTS;
-	else if (dissector_uses_key(flow_dissector,
-				    FLOW_DISSECTOR_KEY_PORTS_RANGE))
-		dissector_ports = FLOW_DISSECTOR_KEY_PORTS_RANGE;
+		key_ports = skb_flow_dissector_target(flow_dissector,
+						      FLOW_DISSECTOR_KEY_PORTS,
+						      target_container);
 
-	if (dissector_ports == FLOW_DISSECTOR_KEY_MAX)
+	if (dissector_uses_key(flow_dissector, FLOW_DISSECTOR_KEY_PORTS_RANGE))
+		key_ports_range = skb_flow_dissector_target(flow_dissector,
+							    FLOW_DISSECTOR_KEY_PORTS_RANGE,
+							    target_container);
+
+	if (!key_ports && !key_ports_range)
 		return;
 
-	key_ports = skb_flow_dissector_target(flow_dissector,
-					      dissector_ports,
-					      target_container);
-	key_ports->ports = __skb_flow_get_ports(skb, nhoff, ip_proto,
-						data, hlen);
+	ports = __skb_flow_get_ports(skb, nhoff, ip_proto, data, hlen);
+
+	if (key_ports)
+		key_ports->ports = ports;
+
+	if (key_ports_range)
+		key_ports_range->tp.ports = ports;
 }
 
 static void
@@ -795,6 +803,7 @@
 				     struct flow_dissector *flow_dissector,
 				     void *target_container)
 {
+	struct flow_dissector_key_ports_range *key_ports_range = NULL;
 	struct flow_dissector_key_ports *key_ports = NULL;
 	struct flow_dissector_key_control *key_control;
 	struct flow_dissector_key_basic *key_basic;
@@ -839,20 +848,21 @@
 		key_control->addr_type = FLOW_DISSECTOR_KEY_IPV6_ADDRS;
 	}
 
-	if (dissector_uses_key(flow_dissector, FLOW_DISSECTOR_KEY_PORTS))
+	if (dissector_uses_key(flow_dissector, FLOW_DISSECTOR_KEY_PORTS)) {
 		key_ports = skb_flow_dissector_target(flow_dissector,
 						      FLOW_DISSECTOR_KEY_PORTS,
 						      target_container);
-	else if (dissector_uses_key(flow_dissector,
-				    FLOW_DISSECTOR_KEY_PORTS_RANGE))
-		key_ports = skb_flow_dissector_target(flow_dissector,
-						      FLOW_DISSECTOR_KEY_PORTS_RANGE,
-						      target_container);
-
-	if (key_ports) {
 		key_ports->src = flow_keys->sport;
 		key_ports->dst = flow_keys->dport;
 	}
+	if (dissector_uses_key(flow_dissector,
+			       FLOW_DISSECTOR_KEY_PORTS_RANGE)) {
+		key_ports_range = skb_flow_dissector_target(flow_dissector,
+							    FLOW_DISSECTOR_KEY_PORTS_RANGE,
+							    target_container);
+		key_ports_range->tp.src = flow_keys->sport;
+		key_ports_range->tp.dst = flow_keys->dport;
+	}
 
 	if (dissector_uses_key(flow_dissector,
 			       FLOW_DISSECTOR_KEY_FLOW_LABEL)) {
@@ -1180,6 +1190,7 @@
 					 VLAN_PRIO_MASK) >> VLAN_PRIO_SHIFT;
 			}
 			key_vlan->vlan_tpid = saved_vlan_tpid;
+			key_vlan->vlan_eth_type = proto;
 		}
 
 		fdret = FLOW_DISSECT_RET_PROTO_AGAIN;
@@ -1276,7 +1287,7 @@
 			break;
 		}
 
-		nhoff += ntohs(hdr->message_length);
+		nhoff += sizeof(struct ptp_header);
 		fdret = FLOW_DISSECT_RET_OUT_GOOD;
 		break;
 	}
@@ -1517,9 +1528,8 @@
 
 	switch (keys->control.addr_type) {
 	case FLOW_DISSECTOR_KEY_IPV4_ADDRS:
-		addr_diff = (__force u32)keys->addrs.v4addrs.dst -
-			    (__force u32)keys->addrs.v4addrs.src;
-		if (addr_diff < 0)
+		if ((__force u32)keys->addrs.v4addrs.dst <
+		    (__force u32)keys->addrs.v4addrs.src)
 			swap(keys->addrs.v4addrs.src, keys->addrs.v4addrs.dst);
 
 		if ((__force u16)keys->ports.dst <
@@ -1613,8 +1623,7 @@
 
 	memset(&keys, 0, sizeof(keys));
 	__skb_flow_dissect(NULL, skb, &flow_keys_dissector_symmetric,
-			   &keys, NULL, 0, 0, 0,
-			   FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL);
+			   &keys, NULL, 0, 0, 0, 0);
 
 	return __flow_hash_from_keys(&keys, &hashrnd);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/flow_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/flow_offload.c
@@ -104,6 +104,13 @@
 }
 EXPORT_SYMBOL(flow_rule_match_ports);
 
+void flow_rule_match_ports_range(const struct flow_rule *rule,
+				 struct flow_match_ports_range *out)
+{
+	FLOW_DISSECTOR_MATCH(rule, FLOW_DISSECTOR_KEY_PORTS_RANGE, out);
+}
+EXPORT_SYMBOL(flow_rule_match_ports_range);
+
 void flow_rule_match_tcp(const struct flow_rule *rule,
 			 struct flow_match_tcp *out)
 {
@@ -565,3 +572,9 @@
 	return list_empty(&bo->cb_list) ? -EOPNOTSUPP : 0;
 }
 EXPORT_SYMBOL(flow_indr_dev_setup_offload);
+
+bool flow_indr_dev_exists(void)
+{
+	return !list_empty(&flow_block_indr_dev_list);
+}
+EXPORT_SYMBOL(flow_indr_dev_exists);
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/gro_cells.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/gro_cells.c
@@ -26,7 +26,7 @@
 
 	cell = this_cpu_ptr(gcells->cells);
 
-	if (skb_queue_len(&cell->napi_skbs) > netdev_max_backlog) {
+	if (skb_queue_len(&cell->napi_skbs) > READ_ONCE(netdev_max_backlog)) {
 drop:
 		atomic_long_inc(&dev->rx_dropped);
 		kfree_skb(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/link_watch.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/link_watch.c
@@ -55,7 +55,7 @@
 	if (operstate == dev->operstate)
 		return;
 
-	write_lock_bh(&dev_base_lock);
+	write_lock(&dev_base_lock);
 
 	switch(dev->link_mode) {
 	case IF_LINK_MODE_TESTING:
@@ -74,7 +74,7 @@
 
 	dev->operstate = operstate;
 
-	write_unlock_bh(&dev_base_lock);
+	write_unlock(&dev_base_lock);
 }
 
 
@@ -138,9 +138,9 @@
 	 * override the existing timer.
 	 */
 	if (test_bit(LW_URGENT, &linkwatch_flags))
-		mod_delayed_work(system_wq, &linkwatch_work, 0);
+		mod_delayed_work(system_unbound_wq, &linkwatch_work, 0);
 	else
-		schedule_delayed_work(&linkwatch_work, delay);
+		queue_delayed_work(system_unbound_wq, &linkwatch_work, delay);
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/lwt_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/lwt_bpf.c
@@ -59,9 +59,8 @@
 			ret = BPF_OK;
 		} else {
 			skb_reset_mac_header(skb);
-			ret = skb_do_redirect(skb);
-			if (ret == 0)
-				ret = BPF_REDIRECT;
+			skb_do_redirect(skb);
+			ret = BPF_REDIRECT;
 		}
 		break;
 
@@ -158,10 +157,8 @@
 	return dst->lwtstate->orig_output(net, sk, skb);
 }
 
-static int xmit_check_hhlen(struct sk_buff *skb)
+static int xmit_check_hhlen(struct sk_buff *skb, int hh_len)
 {
-	int hh_len = skb_dst(skb)->dev->hard_header_len;
-
 	if (skb_headroom(skb) < hh_len) {
 		int nhead = HH_DATA_ALIGN(hh_len - skb_headroom(skb));
 
@@ -256,7 +253,7 @@
 
 	err = dst_output(dev_net(skb_dst(skb)->dev), skb->sk, skb);
 	if (unlikely(err))
-		return err;
+		return net_xmit_errno(err);
 
 	/* ip[6]_finish_output2 understand LWTUNNEL_XMIT_DONE */
 	return LWTUNNEL_XMIT_DONE;
@@ -273,6 +270,7 @@
 
 	bpf = bpf_lwt_lwtunnel(dst->lwtstate);
 	if (bpf->xmit.prog) {
+		int hh_len = dst->dev->hard_header_len;
 		__be16 proto = skb->protocol;
 		int ret;
 
@@ -290,7 +288,7 @@
 			/* If the header was expanded, headroom might be too
 			 * small for L2 header to come, expand as needed.
 			 */
-			ret = xmit_check_hhlen(skb);
+			ret = xmit_check_hhlen(skb, hh_len);
 			if (unlikely(ret))
 				return ret;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/lwtunnel.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/lwtunnel.c
@@ -197,6 +197,10 @@
 			nla_entype = nla_find(attrs, attrlen, RTA_ENCAP_TYPE);
 
 			if (nla_entype) {
+				if (nla_len(nla_entype) < sizeof(u16)) {
+					NL_SET_ERR_MSG(extack, "Invalid RTA_ENCAP_TYPE");
+					return -EINVAL;
+				}
 				encap_type = nla_get_u16(nla_entype);
 
 				if (lwtunnel_valid_encap_type(encap_type,
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/neighbour.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/neighbour.c
@@ -223,10 +223,13 @@
 
 static int neigh_forced_gc(struct neigh_table *tbl)
 {
-	int max_clean = atomic_read(&tbl->gc_entries) - tbl->gc_thresh2;
+	int max_clean = atomic_read(&tbl->gc_entries) -
+			READ_ONCE(tbl->gc_thresh2);
+	u64 tmax = ktime_get_ns() + NSEC_PER_MSEC;
 	unsigned long tref = jiffies - 5 * HZ;
 	struct neighbour *n, *tmp;
 	int shrunk = 0;
+	int loop = 0;
 
 	NEIGH_CACHE_STAT_INC(tbl, forced_gc_runs);
 
@@ -241,7 +244,7 @@
 			    (n->nud_state == NUD_NOARP) ||
 			    (tbl->is_multicast &&
 			     tbl->is_multicast(n->primary_key)) ||
-			    time_after(tref, n->updated))
+			    !time_in_range(n->updated, tref, jiffies))
 				remove = true;
 			write_unlock(&n->lock);
 
@@ -249,11 +252,16 @@
 				shrunk++;
 			if (shrunk >= max_clean)
 				break;
+			if (++loop == 16) {
+				if (ktime_get_ns() > tmax)
+					goto unlock;
+				loop = 0;
+			}
 		}
 	}
 
-	tbl->last_flush = jiffies;
-
+	WRITE_ONCE(tbl->last_flush, jiffies);
+unlock:
 	write_unlock_bh(&tbl->lock);
 
 	return shrunk;
@@ -261,7 +269,17 @@
 
 static void neigh_add_timer(struct neighbour *n, unsigned long when)
 {
+	/* Use safe distance from the jiffies - LONG_MAX point while timer
+	 * is running in DELAY/PROBE state but still show to user space
+	 * large times in the past.
+	 */
+	unsigned long mint = jiffies - (LONG_MAX - 86400 * HZ);
+
 	neigh_hold(n);
+	if (!time_in_range(n->confirmed, mint, jiffies))
+		n->confirmed = mint;
+	if (time_before(n->used, n->confirmed))
+		n->used = n->confirmed;
 	if (unlikely(mod_timer(&n->timer, when))) {
 		printk("NEIGH: BUG, double timer add, state is %x\n",
 		       n->nud_state);
@@ -279,11 +297,26 @@
 	return 0;
 }
 
-static void pneigh_queue_purge(struct sk_buff_head *list)
+static void pneigh_queue_purge(struct sk_buff_head *list, struct net *net)
 {
+	struct sk_buff_head tmp;
+	unsigned long flags;
 	struct sk_buff *skb;
 
-	while ((skb = skb_dequeue(list)) != NULL) {
+	skb_queue_head_init(&tmp);
+	spin_lock_irqsave(&list->lock, flags);
+	skb = skb_peek(list);
+	while (skb != NULL) {
+		struct sk_buff *skb_next = skb_peek_next(skb, list);
+		if (net == NULL || net_eq(dev_net(skb->dev), net)) {
+			__skb_unlink(skb, list);
+			__skb_queue_tail(&tmp, skb);
+		}
+		skb = skb_next;
+	}
+	spin_unlock_irqrestore(&list->lock, flags);
+
+	while ((skb = __skb_dequeue(&tmp))) {
 		dev_put(skb->dev);
 		kfree_skb(skb);
 	}
@@ -357,9 +390,9 @@
 	write_lock_bh(&tbl->lock);
 	neigh_flush_dev(tbl, dev, skip_perm);
 	pneigh_ifdown_and_unlock(tbl, dev);
-
-	del_timer_sync(&tbl->proxy_timer);
-	pneigh_queue_purge(&tbl->proxy_queue);
+	pneigh_queue_purge(&tbl->proxy_queue, dev ? dev_net(dev) : NULL);
+	if (skb_queue_empty_lockless(&tbl->proxy_queue))
+		del_timer_sync(&tbl->proxy_timer);
 	return 0;
 }
 
@@ -379,21 +412,21 @@
 
 static struct neighbour *neigh_alloc(struct neigh_table *tbl,
 				     struct net_device *dev,
-				     bool exempt_from_gc)
+				     u8 flags, bool exempt_from_gc)
 {
 	struct neighbour *n = NULL;
 	unsigned long now = jiffies;
-	int entries;
+	int entries, gc_thresh3;
 
 	if (exempt_from_gc)
 		goto do_alloc;
 
 	entries = atomic_inc_return(&tbl->gc_entries) - 1;
-	if (entries >= tbl->gc_thresh3 ||
-	    (entries >= tbl->gc_thresh2 &&
-	     time_after(now, tbl->last_flush + 5 * HZ))) {
-		if (!neigh_forced_gc(tbl) &&
-		    entries >= tbl->gc_thresh3) {
+	gc_thresh3 = READ_ONCE(tbl->gc_thresh3);
+	if (entries >= gc_thresh3 ||
+	    (entries >= READ_ONCE(tbl->gc_thresh2) &&
+	     time_after(now, READ_ONCE(tbl->last_flush) + 5 * HZ))) {
+		if (!neigh_forced_gc(tbl) && entries >= gc_thresh3) {
 			net_info_ratelimited("%s: neighbor table overflow!\n",
 					     tbl->id);
 			NEIGH_CACHE_STAT_INC(tbl, table_fulls);
@@ -412,6 +445,7 @@
 	n->updated	  = n->used = now;
 	n->nud_state	  = NUD_NONE;
 	n->output	  = neigh_blackhole;
+	n->flags	  = flags;
 	seqlock_init(&n->hh.hh_lock);
 	n->parms	  = neigh_parms_clone(&tbl->parms);
 	timer_setup(&n->timer, neigh_timer_handler, 0);
@@ -544,50 +578,18 @@
 }
 EXPORT_SYMBOL(neigh_lookup);
 
-struct neighbour *neigh_lookup_nodev(struct neigh_table *tbl, struct net *net,
-				     const void *pkey)
+static struct neighbour *
+___neigh_create(struct neigh_table *tbl, const void *pkey,
+		struct net_device *dev, u8 flags,
+		bool exempt_from_gc, bool want_ref)
 {
-	struct neighbour *n;
-	unsigned int key_len = tbl->key_len;
-	u32 hash_val;
+	u32 hash_val, key_len = tbl->key_len;
+	struct neighbour *n1, *rc, *n;
 	struct neigh_hash_table *nht;
-
-	NEIGH_CACHE_STAT_INC(tbl, lookups);
-
-	rcu_read_lock_bh();
-	nht = rcu_dereference_bh(tbl->nht);
-	hash_val = tbl->hash(pkey, NULL, nht->hash_rnd) >> (32 - nht->hash_shift);
-
-	for (n = rcu_dereference_bh(nht->hash_buckets[hash_val]);
-	     n != NULL;
-	     n = rcu_dereference_bh(n->next)) {
-		if (!memcmp(n->primary_key, pkey, key_len) &&
-		    net_eq(dev_net(n->dev), net)) {
-			if (!refcount_inc_not_zero(&n->refcnt))
-				n = NULL;
-			NEIGH_CACHE_STAT_INC(tbl, hits);
-			break;
-		}
-	}
-
-	rcu_read_unlock_bh();
-	return n;
-}
-EXPORT_SYMBOL(neigh_lookup_nodev);
-
-static struct neighbour *___neigh_create(struct neigh_table *tbl,
-					 const void *pkey,
-					 struct net_device *dev,
-					 bool exempt_from_gc, bool want_ref)
-{
-	struct neighbour *n1, *rc, *n = neigh_alloc(tbl, dev, exempt_from_gc);
-	u32 hash_val;
-	unsigned int key_len = tbl->key_len;
 	int error;
-	struct neigh_hash_table *nht;
 
+	n = neigh_alloc(tbl, dev, flags, exempt_from_gc);
 	trace_neigh_create(tbl, dev, pkey, n, exempt_from_gc);
-
 	if (!n) {
 		rc = ERR_PTR(-ENOBUFS);
 		goto out;
@@ -674,7 +676,7 @@
 struct neighbour *__neigh_create(struct neigh_table *tbl, const void *pkey,
 				 struct net_device *dev, bool want_ref)
 {
-	return ___neigh_create(tbl, pkey, dev, false, want_ref);
+	return ___neigh_create(tbl, pkey, dev, 0, false, want_ref);
 }
 EXPORT_SYMBOL(__neigh_create);
 
@@ -733,11 +735,10 @@
 
 	ASSERT_RTNL();
 
-	n = kmalloc(sizeof(*n) + key_len, GFP_KERNEL);
+	n = kzalloc(sizeof(*n) + key_len, GFP_KERNEL);
 	if (!n)
 		goto out;
 
-	n->protocol = 0;
 	write_pnet(&n->net, net);
 	memcpy(n->key, pkey, key_len);
 	n->dev = dev;
@@ -904,13 +905,14 @@
 
 	if (time_after(jiffies, tbl->last_rand + 300 * HZ)) {
 		struct neigh_parms *p;
-		tbl->last_rand = jiffies;
+
+		WRITE_ONCE(tbl->last_rand, jiffies);
 		list_for_each_entry(p, &tbl->parms_list, list)
 			p->reachable_time =
 				neigh_rand_reach_time(NEIGH_VAR(p, BASE_REACHABLE_TIME));
 	}
 
-	if (atomic_read(&tbl->entries) < tbl->gc_thresh1)
+	if (atomic_read(&tbl->entries) < READ_ONCE(tbl->gc_thresh1))
 		goto out;
 
 	for (i = 0 ; i < (1 << nht->hash_shift); i++) {
@@ -929,13 +931,17 @@
 				goto next_elt;
 			}
 
-			if (time_before(n->used, n->confirmed))
+			if (time_before(n->used, n->confirmed) &&
+			    time_is_before_eq_jiffies(n->confirmed))
 				n->used = n->confirmed;
 
 			if (refcount_read(&n->refcnt) == 1 &&
 			    (state == NUD_FAILED ||
-			     time_after(jiffies, n->used + NEIGH_VAR(n->parms, GC_STALETIME)))) {
-				*np = n->next;
+			     !time_in_range_open(jiffies, n->used,
+						 n->used + NEIGH_VAR(n->parms, GC_STALETIME)))) {
+				rcu_assign_pointer(*np,
+					rcu_dereference_protected(n->next,
+						lockdep_is_held(&tbl->lock)));
 				neigh_mark_dead(n);
 				write_unlock(&n->lock);
 				neigh_cleanup_and_release(n);
@@ -1217,7 +1223,7 @@
 				lladdr instead of overriding it
 				if it is different.
 	NEIGH_UPDATE_F_ADMIN	means that the change is administrative.
-
+	NEIGH_UPDATE_F_USE	means that the entry is user triggered.
 	NEIGH_UPDATE_F_OVERRIDE_ISROUTER allows to override existing
 				NTF_ROUTER flag.
 	NEIGH_UPDATE_F_ISROUTER	indicates if the neighbour is known as
@@ -1255,6 +1261,12 @@
 		goto out;
 
 	ext_learn_change = neigh_update_ext_learned(neigh, flags, &notify);
+	if (flags & NEIGH_UPDATE_F_USE) {
+		new = old & ~NUD_PERMANENT;
+		neigh->nud_state = new;
+		err = 0;
+		goto out;
+	}
 
 	if (!(new & NUD_VALID)) {
 		neigh_del_timer(neigh);
@@ -1730,7 +1742,7 @@
 	/* It is not clean... Fix it to unload IPv6 module safely */
 	cancel_delayed_work_sync(&tbl->gc_work);
 	del_timer_sync(&tbl->proxy_timer);
-	pneigh_queue_purge(&tbl->proxy_queue);
+	pneigh_queue_purge(&tbl->proxy_queue, NULL);
 	neigh_ifdown(tbl, NULL);
 	if (atomic_read(&tbl->entries))
 		pr_crit("neighbour leakage\n");
@@ -1762,9 +1774,6 @@
 	case AF_INET6:
 		tbl = neigh_tables[NEIGH_ND_TABLE];
 		break;
-	case AF_DECnet:
-		tbl = neigh_tables[NEIGH_DN_TABLE];
-		break;
 	}
 
 	return tbl;
@@ -1942,7 +1951,9 @@
 
 		exempt_from_gc = ndm->ndm_state & NUD_PERMANENT ||
 				 ndm->ndm_flags & NTF_EXT_LEARNED;
-		neigh = ___neigh_create(tbl, dst, dev, exempt_from_gc, true);
+		neigh = ___neigh_create(tbl, dst, dev,
+					ndm->ndm_flags & NTF_EXT_LEARNED,
+					exempt_from_gc, true);
 		if (IS_ERR(neigh)) {
 			err = PTR_ERR(neigh);
 			goto out;
@@ -1961,22 +1972,20 @@
 
 	if (protocol)
 		neigh->protocol = protocol;
-
 	if (ndm->ndm_flags & NTF_EXT_LEARNED)
 		flags |= NEIGH_UPDATE_F_EXT_LEARNED;
-
 	if (ndm->ndm_flags & NTF_ROUTER)
 		flags |= NEIGH_UPDATE_F_ISROUTER;
+	if (ndm->ndm_flags & NTF_USE)
+		flags |= NEIGH_UPDATE_F_USE;
 
-	if (ndm->ndm_flags & NTF_USE) {
+	err = __neigh_update(neigh, lladdr, ndm->ndm_state, flags,
+			     NETLINK_CB(skb).portid, extack);
+	if (!err && ndm->ndm_flags & NTF_USE) {
 		neigh_event_send(neigh, NULL);
 		err = 0;
-	} else
-		err = __neigh_update(neigh, lladdr, ndm->ndm_state, flags,
-				     NETLINK_CB(skb).portid, extack);
-
+	}
 	neigh_release(neigh);
-
 out:
 	return err;
 }
@@ -2047,15 +2056,16 @@
 	ndtmsg->ndtm_pad2   = 0;
 
 	if (nla_put_string(skb, NDTA_NAME, tbl->id) ||
-	    nla_put_msecs(skb, NDTA_GC_INTERVAL, tbl->gc_interval, NDTA_PAD) ||
-	    nla_put_u32(skb, NDTA_THRESH1, tbl->gc_thresh1) ||
-	    nla_put_u32(skb, NDTA_THRESH2, tbl->gc_thresh2) ||
-	    nla_put_u32(skb, NDTA_THRESH3, tbl->gc_thresh3))
+	    nla_put_msecs(skb, NDTA_GC_INTERVAL, READ_ONCE(tbl->gc_interval),
+			  NDTA_PAD) ||
+	    nla_put_u32(skb, NDTA_THRESH1, READ_ONCE(tbl->gc_thresh1)) ||
+	    nla_put_u32(skb, NDTA_THRESH2, READ_ONCE(tbl->gc_thresh2)) ||
+	    nla_put_u32(skb, NDTA_THRESH3, READ_ONCE(tbl->gc_thresh3)))
 		goto nla_put_failure;
 	{
 		unsigned long now = jiffies;
-		long flush_delta = now - tbl->last_flush;
-		long rand_delta = now - tbl->last_rand;
+		long flush_delta = now - READ_ONCE(tbl->last_flush);
+		long rand_delta = now - READ_ONCE(tbl->last_rand);
 		struct neigh_hash_table *nht;
 		struct ndt_config ndc = {
 			.ndtc_key_len		= tbl->key_len,
@@ -2063,7 +2073,7 @@
 			.ndtc_entries		= atomic_read(&tbl->entries),
 			.ndtc_last_flush	= jiffies_to_msecs(flush_delta),
 			.ndtc_last_rand		= jiffies_to_msecs(rand_delta),
-			.ndtc_proxy_qlen	= tbl->proxy_queue.qlen,
+			.ndtc_proxy_qlen	= READ_ONCE(tbl->proxy_queue.qlen),
 		};
 
 		rcu_read_lock_bh();
@@ -2086,17 +2096,17 @@
 			struct neigh_statistics	*st;
 
 			st = per_cpu_ptr(tbl->stats, cpu);
-			ndst.ndts_allocs		+= st->allocs;
-			ndst.ndts_destroys		+= st->destroys;
-			ndst.ndts_hash_grows		+= st->hash_grows;
-			ndst.ndts_res_failed		+= st->res_failed;
-			ndst.ndts_lookups		+= st->lookups;
-			ndst.ndts_hits			+= st->hits;
-			ndst.ndts_rcv_probes_mcast	+= st->rcv_probes_mcast;
-			ndst.ndts_rcv_probes_ucast	+= st->rcv_probes_ucast;
-			ndst.ndts_periodic_gc_runs	+= st->periodic_gc_runs;
-			ndst.ndts_forced_gc_runs	+= st->forced_gc_runs;
-			ndst.ndts_table_fulls		+= st->table_fulls;
+			ndst.ndts_allocs		+= READ_ONCE(st->allocs);
+			ndst.ndts_destroys		+= READ_ONCE(st->destroys);
+			ndst.ndts_hash_grows		+= READ_ONCE(st->hash_grows);
+			ndst.ndts_res_failed		+= READ_ONCE(st->res_failed);
+			ndst.ndts_lookups		+= READ_ONCE(st->lookups);
+			ndst.ndts_hits			+= READ_ONCE(st->hits);
+			ndst.ndts_rcv_probes_mcast	+= READ_ONCE(st->rcv_probes_mcast);
+			ndst.ndts_rcv_probes_ucast	+= READ_ONCE(st->rcv_probes_ucast);
+			ndst.ndts_periodic_gc_runs	+= READ_ONCE(st->periodic_gc_runs);
+			ndst.ndts_forced_gc_runs	+= READ_ONCE(st->forced_gc_runs);
+			ndst.ndts_table_fulls		+= READ_ONCE(st->table_fulls);
 		}
 
 		if (nla_put_64bit(skb, NDTA_STATS, sizeof(ndst), &ndst,
@@ -2163,6 +2173,7 @@
 static const struct nla_policy nl_ntbl_parm_policy[NDTPA_MAX+1] = {
 	[NDTPA_IFINDEX]			= { .type = NLA_U32 },
 	[NDTPA_QUEUE_LEN]		= { .type = NLA_U32 },
+	[NDTPA_QUEUE_LENBYTES]		= { .type = NLA_U32 },
 	[NDTPA_PROXY_QLEN]		= { .type = NLA_U32 },
 	[NDTPA_APP_PROBES]		= { .type = NLA_U32 },
 	[NDTPA_UCAST_PROBES]		= { .type = NLA_U32 },
@@ -2320,16 +2331,16 @@
 		goto errout_tbl_lock;
 
 	if (tb[NDTA_THRESH1])
-		tbl->gc_thresh1 = nla_get_u32(tb[NDTA_THRESH1]);
+		WRITE_ONCE(tbl->gc_thresh1, nla_get_u32(tb[NDTA_THRESH1]));
 
 	if (tb[NDTA_THRESH2])
-		tbl->gc_thresh2 = nla_get_u32(tb[NDTA_THRESH2]);
+		WRITE_ONCE(tbl->gc_thresh2, nla_get_u32(tb[NDTA_THRESH2]));
 
 	if (tb[NDTA_THRESH3])
-		tbl->gc_thresh3 = nla_get_u32(tb[NDTA_THRESH3]);
+		WRITE_ONCE(tbl->gc_thresh3, nla_get_u32(tb[NDTA_THRESH3]));
 
 	if (tb[NDTA_GC_INTERVAL])
-		tbl->gc_interval = nla_get_msecs(tb[NDTA_GC_INTERVAL]);
+		WRITE_ONCE(tbl->gc_interval, nla_get_msecs(tb[NDTA_GC_INTERVAL]));
 
 	err = 0;
 
@@ -2728,6 +2739,7 @@
 	err = neigh_valid_dump_req(nlh, cb->strict_check, &filter, cb->extack);
 	if (err < 0 && cb->strict_check)
 		return err;
+	err = 0;
 
 	s_t = cb->args[0];
 
@@ -3358,10 +3370,12 @@
 static void __neigh_notify(struct neighbour *n, int type, int flags,
 			   u32 pid)
 {
-	struct net *net = dev_net(n->dev);
 	struct sk_buff *skb;
 	int err = -ENOBUFS;
+	struct net *net;
 
+	rcu_read_lock();
+	net = dev_net_rcu(n->dev);
 	skb = nlmsg_new(neigh_nlmsg_size(), GFP_ATOMIC);
 	if (skb == NULL)
 		goto errout;
@@ -3374,10 +3388,11 @@
 		goto errout;
 	}
 	rtnl_notify(skb, net, 0, RTNLGRP_NEIGH, NULL, GFP_ATOMIC);
-	return;
+	goto out;
 errout:
-	if (err < 0)
-		rtnl_set_sk_err(net, RTNLGRP_NEIGH, err);
+	rtnl_set_sk_err(net, RTNLGRP_NEIGH, err);
+out:
+	rcu_read_unlock();
 }
 
 void neigh_app_ns(struct neighbour *n)
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/net-procfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/net-procfs.c
@@ -190,12 +190,23 @@
 	.show  = softnet_seq_show,
 };
 
-static void *ptype_get_idx(loff_t pos)
+static void *ptype_get_idx(struct seq_file *seq, loff_t pos)
 {
+	struct list_head *ptype_list = NULL;
 	struct packet_type *pt = NULL;
+	struct net_device *dev;
 	loff_t i = 0;
 	int t;
 
+	for_each_netdev_rcu(seq_file_net(seq), dev) {
+		ptype_list = &dev->ptype_all;
+		list_for_each_entry_rcu(pt, ptype_list, list) {
+			if (i == pos)
+				return pt;
+			++i;
+		}
+	}
+
 	list_for_each_entry_rcu(pt, &ptype_all, list) {
 		if (i == pos)
 			return pt;
@@ -216,22 +227,40 @@
 	__acquires(RCU)
 {
 	rcu_read_lock();
-	return *pos ? ptype_get_idx(*pos - 1) : SEQ_START_TOKEN;
+	return *pos ? ptype_get_idx(seq, *pos - 1) : SEQ_START_TOKEN;
 }
 
 static void *ptype_seq_next(struct seq_file *seq, void *v, loff_t *pos)
 {
+	struct net_device *dev;
 	struct packet_type *pt;
 	struct list_head *nxt;
 	int hash;
 
 	++*pos;
 	if (v == SEQ_START_TOKEN)
-		return ptype_get_idx(0);
+		return ptype_get_idx(seq, 0);
 
 	pt = v;
 	nxt = pt->list.next;
+	if (pt->dev) {
+		if (nxt != &pt->dev->ptype_all)
+			goto found;
+
+		dev = pt->dev;
+		for_each_netdev_continue_rcu(seq_file_net(seq), dev) {
+			if (!list_empty(&dev->ptype_all)) {
+				nxt = dev->ptype_all.next;
+				goto found;
+			}
+		}
+
+		nxt = ptype_all.next;
+		goto ptype_all;
+	}
+
 	if (pt->type == htons(ETH_P_ALL)) {
+ptype_all:
 		if (nxt != &ptype_all)
 			goto found;
 		hash = 0;
@@ -260,7 +289,8 @@
 
 	if (v == SEQ_START_TOKEN)
 		seq_puts(seq, "Type Device      Function\n");
-	else if (pt->dev == NULL || dev_net(pt->dev) == seq_file_net(seq)) {
+	else if ((!pt->af_packet_net || net_eq(pt->af_packet_net, seq_file_net(seq))) &&
+		 (!pt->dev || net_eq(dev_net(pt->dev), seq_file_net(seq)))) {
 		if (pt->type == htons(ETH_P_ALL))
 			seq_puts(seq, "ALL ");
 		else
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/net-sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/net-sysfs.c
@@ -32,6 +32,7 @@
 static const char fmt_ulong[] = "%lu\n";
 static const char fmt_u64[] = "%llu\n";
 
+/* Caller holds RTNL or dev_base_lock */
 static inline int dev_isalive(const struct net_device *dev)
 {
 	return dev->reg_state <= NETREG_REGISTERED;
@@ -175,6 +176,14 @@
 static ssize_t carrier_store(struct device *dev, struct device_attribute *attr,
 			     const char *buf, size_t len)
 {
+	struct net_device *netdev = to_net_dev(dev);
+
+	/* The check is also done in change_carrier; this helps returning early
+	 * without hitting the trylock/restart in netdev_store.
+	 */
+	if (!netdev->netdev_ops->ndo_change_carrier)
+		return -EOPNOTSUPP;
+
 	return netdev_store(dev, attr, buf, len, change_carrier);
 }
 
@@ -196,6 +205,12 @@
 	struct net_device *netdev = to_net_dev(dev);
 	int ret = -EINVAL;
 
+	/* The check is also done in __ethtool_get_link_ksettings; this helps
+	 * returning early without hitting the trylock/restart below.
+	 */
+	if (!netdev->ethtool_ops->get_link_ksettings)
+		return ret;
+
 	if (!rtnl_trylock())
 		return restart_syscall();
 
@@ -216,6 +231,12 @@
 	struct net_device *netdev = to_net_dev(dev);
 	int ret = -EINVAL;
 
+	/* The check is also done in __ethtool_get_link_ksettings; this helps
+	 * returning early without hitting the trylock/restart below.
+	 */
+	if (!netdev->ethtool_ops->get_link_ksettings)
+		return ret;
+
 	if (!rtnl_trylock())
 		return restart_syscall();
 
@@ -468,6 +489,14 @@
 				struct device_attribute *attr,
 				const char *buf, size_t len)
 {
+	struct net_device *netdev = to_net_dev(dev);
+
+	/* The check is also done in change_proto_down; this helps returning
+	 * early without hitting the trylock/restart in netdev_store.
+	 */
+	if (!netdev->netdev_ops->ndo_change_proto_down)
+		return -EOPNOTSUPP;
+
 	return netdev_store(dev, attr, buf, len, change_proto_down);
 }
 NETDEVICE_SHOW_RW(proto_down, fmt_dec);
@@ -478,6 +507,12 @@
 	struct net_device *netdev = to_net_dev(dev);
 	ssize_t ret = -EINVAL;
 
+	/* The check is also done in dev_get_phys_port_id; this helps returning
+	 * early without hitting the trylock/restart below.
+	 */
+	if (!netdev->netdev_ops->ndo_get_phys_port_id)
+		return -EOPNOTSUPP;
+
 	if (!rtnl_trylock())
 		return restart_syscall();
 
@@ -500,6 +535,13 @@
 	struct net_device *netdev = to_net_dev(dev);
 	ssize_t ret = -EINVAL;
 
+	/* The checks are also done in dev_get_phys_port_name; this helps
+	 * returning early without hitting the trylock/restart below.
+	 */
+	if (!netdev->netdev_ops->ndo_get_phys_port_name &&
+	    !netdev->netdev_ops->ndo_get_devlink_port)
+		return -EOPNOTSUPP;
+
 	if (!rtnl_trylock())
 		return restart_syscall();
 
@@ -522,6 +564,14 @@
 	struct net_device *netdev = to_net_dev(dev);
 	ssize_t ret = -EINVAL;
 
+	/* The checks are also done in dev_get_phys_port_name; this helps
+	 * returning early without hitting the trylock/restart below. This works
+	 * because recurse is false when calling dev_get_port_parent_id.
+	 */
+	if (!netdev->netdev_ops->ndo_get_port_parent_id &&
+	    !netdev->netdev_ops->ndo_get_devlink_port)
+		return -EOPNOTSUPP;
+
 	if (!rtnl_trylock())
 		return restart_syscall();
 
@@ -1226,6 +1276,12 @@
 	if (!capable(CAP_NET_ADMIN))
 		return -EPERM;
 
+	/* The check is also done later; this helps returning early without
+	 * hitting the trylock/restart below.
+	 */
+	if (!dev->netdev_ops->ndo_set_tx_maxrate)
+		return -EOPNOTSUPP;
+
 	err = kstrtou32(buf, 10, &rate);
 	if (err < 0)
 		return err;
@@ -1765,6 +1821,9 @@
 
 	net_rx_queue_update_kobjects(dev, real_rx, 0);
 	netdev_queue_update_kobjects(dev, real_tx, 0);
+
+	dev->real_num_rx_queues = 0;
+	dev->real_num_tx_queues = 0;
 #ifdef CONFIG_SYSFS
 	kset_unregister(dev->queues_kset);
 #endif
@@ -1869,7 +1928,7 @@
 	.get_ownership = net_get_ownership,
 };
 
-#ifdef CONFIG_OF_NET
+#ifdef CONFIG_OF
 static int of_dev_node_match(struct device *dev, const void *data)
 {
 	for (; dev; dev = dev->parent) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/net_namespace.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/net_namespace.c
@@ -44,13 +44,7 @@
 static struct key_tag init_net_key_domain = { .usage = REFCOUNT_INIT(1) };
 #endif
 
-struct net init_net = {
-	.ns.count	= REFCOUNT_INIT(1),
-	.dev_base_head	= LIST_HEAD_INIT(init_net.dev_base_head),
-#ifdef CONFIG_KEYS
-	.key_domain	= &init_net_key_domain,
-#endif
-};
+struct net init_net;
 EXPORT_SYMBOL(init_net);
 
 static bool init_net_initialized;
@@ -74,12 +68,15 @@
 
 static struct net_generic *net_alloc_generic(void)
 {
+	unsigned int gen_ptrs = READ_ONCE(max_gen_ptrs);
+	unsigned int generic_size;
 	struct net_generic *ng;
-	unsigned int generic_size = offsetof(struct net_generic, ptr[max_gen_ptrs]);
+
+	generic_size = offsetof(struct net_generic, ptr[gen_ptrs]);
 
 	ng = kzalloc(generic_size, GFP_KERNEL);
 	if (ng)
-		ng->s.len = max_gen_ptrs;
+		ng->s.len = gen_ptrs;
 
 	return ng;
 }
@@ -123,6 +120,7 @@
 
 static int ops_init(const struct pernet_operations *ops, struct net *net)
 {
+	struct net_generic *ng;
 	int err = -ENOMEM;
 	void *data = NULL;
 
@@ -141,6 +139,12 @@
 	if (!err)
 		return 0;
 
+	if (ops->id && ops->size) {
+		ng = rcu_dereference_protected(net->gen,
+					       lockdep_is_held(&pernet_ops_rwsem));
+		ng->ptr[*ops->id] = NULL;
+	}
+
 cleanup:
 	kfree(data);
 
@@ -164,8 +168,10 @@
 {
 	struct net *net;
 	if (ops->exit) {
-		list_for_each_entry(net, net_exit_list, exit_list)
+		list_for_each_entry(net, net_exit_list, exit_list) {
 			ops->exit(net);
+			cond_resched();
+		}
 	}
 	if (ops->exit_batch)
 		ops->exit_batch(net_exit_list);
@@ -307,8 +313,9 @@
 {
 	/* Must be called with pernet_ops_rwsem held */
 	const struct pernet_operations *ops, *saved_ops;
-	int error = 0;
 	LIST_HEAD(net_exit_list);
+	LIST_HEAD(dev_kill_list);
+	int error = 0;
 
 	refcount_set(&net->ns.count, 1);
 	refcount_set(&net->passive, 1);
@@ -345,6 +352,15 @@
 	synchronize_rcu();
 
 	ops = saved_ops;
+	rtnl_lock();
+	list_for_each_entry_continue_reverse(ops, &pernet_list, list) {
+		if (ops->exit_batch_rtnl)
+			ops->exit_batch_rtnl(&net_exit_list, &dev_kill_list);
+	}
+	unregister_netdevice_many(&dev_kill_list);
+	rtnl_unlock();
+
+	ops = saved_ops;
 	list_for_each_entry_continue_reverse(ops, &pernet_list, list)
 		ops_exit_list(ops, &net_exit_list);
 
@@ -424,11 +440,28 @@
 	goto out;
 }
 
+static LLIST_HEAD(defer_free_list);
+
+static void net_complete_free(void)
+{
+	struct llist_node *kill_list;
+	struct net *net, *next;
+
+	/* Get the list of namespaces to free from last round. */
+	kill_list = llist_del_all(&defer_free_list);
+
+	llist_for_each_entry_safe(net, next, kill_list, defer_free_list)
+		kmem_cache_free(net_cachep, net);
+
+}
+
 static void net_free(struct net *net)
 {
 	if (refcount_dec_and_test(&net->passive)) {
 		kfree(rcu_access_pointer(net->gen));
-		kmem_cache_free(net_cachep, net);
+
+		/* Wait for an extra rcu_barrier() before final free. */
+		llist_add(&net->defer_free_list, &defer_free_list);
 	}
 }
 
@@ -473,7 +506,9 @@
 
 	if (rv < 0) {
 put_userns:
+#ifdef CONFIG_KEYS
 		key_remove_domain(net->key_domain);
+#endif
 		put_user_ns(user_ns);
 		net_free(net);
 dec_ucounts:
@@ -546,6 +581,7 @@
 	struct net *net, *tmp, *last;
 	struct llist_node *net_kill_list;
 	LIST_HEAD(net_exit_list);
+	LIST_HEAD(dev_kill_list);
 
 	/* Atomically snapshot the list of namespaces to cleanup */
 	net_kill_list = llist_del_all(&cleanup_list);
@@ -586,6 +622,14 @@
 	 */
 	synchronize_rcu();
 
+	rtnl_lock();
+	list_for_each_entry_reverse(ops, &pernet_list, list) {
+		if (ops->exit_batch_rtnl)
+			ops->exit_batch_rtnl(&net_exit_list, &dev_kill_list);
+	}
+	unregister_netdevice_many(&dev_kill_list);
+	rtnl_unlock();
+
 	/* Run all of the network namespace exit methods */
 	list_for_each_entry_reverse(ops, &pernet_list, list)
 		ops_exit_list(ops, &net_exit_list);
@@ -601,11 +645,15 @@
 	 */
 	rcu_barrier();
 
+	net_complete_free();
+
 	/* Finally it is safe to free my network namespace structure */
 	list_for_each_entry_safe(net, tmp, &net_exit_list, exit_list) {
 		list_del_init(&net->exit_list);
 		dec_net_namespaces(net->ucounts);
+#ifdef CONFIG_KEYS
 		key_remove_domain(net->key_domain);
+#endif
 		put_user_ns(net->user_ns);
 		net_free(net);
 	}
@@ -641,11 +689,16 @@
  * get_net_ns - increment the refcount of the network namespace
  * @ns: common namespace (net)
  *
- * Returns the net's common namespace.
+ * Returns the net's common namespace or ERR_PTR() if ref is zero.
  */
 struct ns_common *get_net_ns(struct ns_common *ns)
 {
-	return &get_net(container_of(ns, struct net, ns))->ns;
+	struct net *net;
+
+	net = maybe_get_net(container_of(ns, struct net, ns));
+	if (net)
+		return &net->ns;
+	return ERR_PTR(-EINVAL);
 }
 EXPORT_SYMBOL_GPL(get_net_ns);
 
@@ -1075,7 +1128,7 @@
 	rtnl_set_sk_err(net, RTNLGRP_NSID, err);
 }
 
-static int __init net_ns_init(void)
+void __init net_ns_init(void)
 {
 	struct net_generic *ng;
 
@@ -1096,6 +1149,9 @@
 
 	rcu_assign_pointer(init_net.gen, ng);
 
+#ifdef CONFIG_KEYS
+	init_net.key_domain = &init_net_key_domain;
+#endif
 	down_write(&pernet_ops_rwsem);
 	if (setup_net(&init_net, &init_user_ns))
 		panic("Could not setup the initial network namespace");
@@ -1110,17 +1166,23 @@
 		      RTNL_FLAG_DOIT_UNLOCKED);
 	rtnl_register(PF_UNSPEC, RTM_GETNSID, rtnl_net_getid, rtnl_net_dumpid,
 		      RTNL_FLAG_DOIT_UNLOCKED);
-
-	return 0;
 }
 
-pure_initcall(net_ns_init);
-
 static void free_exit_list(struct pernet_operations *ops, struct list_head *net_exit_list)
 {
 	ops_pre_exit_list(ops, net_exit_list);
 	synchronize_rcu();
+
+	if (ops->exit_batch_rtnl) {
+		LIST_HEAD(dev_kill_list);
+
+		rtnl_lock();
+		ops->exit_batch_rtnl(net_exit_list, &dev_kill_list);
+		unregister_netdevice_many(&dev_kill_list);
+		rtnl_unlock();
+	}
 	ops_exit_list(ops, net_exit_list);
+
 	ops_free_list(ops, net_exit_list);
 }
 
@@ -1205,7 +1267,11 @@
 		if (error < 0)
 			return error;
 		*ops->id = error;
-		max_gen_ptrs = max(max_gen_ptrs, *ops->id + 1);
+		/* This does not require READ_ONCE as writers already hold
+		 * pernet_ops_rwsem. But WRITE_ONCE is needed to protect
+		 * net_alloc_generic.
+		 */
+		WRITE_ONCE(max_gen_ptrs, max(max_gen_ptrs, *ops->id + 1));
 	}
 	error = __register_pernet_operations(list, ops);
 	if (error) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/netpoll.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/netpoll.c
@@ -137,6 +137,20 @@
 	}
 }
 
+static int netif_local_xmit_active(struct net_device *dev)
+{
+	int i;
+
+	for (i = 0; i < dev->num_tx_queues; i++) {
+		struct netdev_queue *txq = netdev_get_tx_queue(dev, i);
+
+		if (READ_ONCE(txq->xmit_lock_owner) == smp_processor_id())
+			return 1;
+	}
+
+	return 0;
+}
+
 static void poll_one_napi(struct napi_struct *napi)
 {
 	int work;
@@ -183,7 +197,10 @@
 	if (!ni || down_trylock(&ni->dev_lock))
 		return;
 
-	if (!netif_running(dev)) {
+	/* Some drivers will take the same locks in poll and xmit,
+	 * we can't poll if local CPU is already in xmit.
+	 */
+	if (!netif_running(dev) || netif_local_xmit_active(dev)) {
 		up(&ni->dev_lock);
 		return;
 	}
@@ -299,7 +316,7 @@
 	struct napi_struct *napi;
 
 	list_for_each_entry_rcu(napi, &dev->napi_list, dev_list) {
-		if (napi->poll_owner == smp_processor_id())
+		if (READ_ONCE(napi->poll_owner) == smp_processor_id())
 			return 1;
 	}
 	return 0;
@@ -309,6 +326,7 @@
 static netdev_tx_t __netpoll_send_skb(struct netpoll *np, struct sk_buff *skb)
 {
 	netdev_tx_t status = NETDEV_TX_BUSY;
+	netdev_tx_t ret = NET_XMIT_DROP;
 	struct net_device *dev;
 	unsigned long tries;
 	/* It is up to the caller to keep npinfo alive. */
@@ -317,11 +335,12 @@
 	lockdep_assert_irqs_disabled();
 
 	dev = np->dev;
+	rcu_read_lock();
 	npinfo = rcu_dereference_bh(dev->npinfo);
 
 	if (!npinfo || !netif_running(dev) || !netif_device_present(dev)) {
 		dev_kfree_skb_irq(skb);
-		return NET_XMIT_DROP;
+		goto out;
 	}
 
 	/* don't get messages out of order, and no recursion */
@@ -360,7 +379,10 @@
 		skb_queue_tail(&npinfo->txq, skb);
 		schedule_delayed_work(&npinfo->tx_work,0);
 	}
-	return NETDEV_TX_OK;
+	ret = NETDEV_TX_OK;
+out:
+	rcu_read_unlock();
+	return ret;
 }
 
 netdev_tx_t netpoll_send_skb(struct netpoll *np, struct sk_buff *skb)
@@ -556,7 +578,7 @@
 		if ((delim = strchr(cur, ',')) == NULL)
 			goto parse_failed;
 		*delim = 0;
-		strlcpy(np->dev_name, cur, sizeof(np->dev_name));
+		strscpy(np->dev_name, cur, sizeof(np->dev_name));
 		cur = delim;
 	}
 	cur++;
@@ -610,7 +632,7 @@
 	int err;
 
 	np->dev = ndev;
-	strlcpy(np->dev_name, ndev->name, IFNAMSIZ);
+	strscpy(np->dev_name, ndev->name, IFNAMSIZ);
 
 	if (ndev->priv_flags & IFF_DISABLE_NETPOLL) {
 		np_err(np, "%s doesn't support polling, aborting\n",
@@ -619,7 +641,7 @@
 		goto out;
 	}
 
-	if (!ndev->npinfo) {
+	if (!rcu_access_pointer(ndev->npinfo)) {
 		npinfo = kmalloc(sizeof(*npinfo), GFP_KERNEL);
 		if (!npinfo) {
 			err = -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/of_net.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/of_net.c
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * OF helpers for network devices.
+ *
+ * Initially copied out of arch/powerpc/kernel/prom_parse.c
+ */
+#include <linux/etherdevice.h>
+#include <linux/kernel.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/export.h>
+#include <linux/device.h>
+#include <linux/nvmem-consumer.h>
+
+/**
+ * of_get_phy_mode - Get phy mode for given device_node
+ * @np:	Pointer to the given device_node
+ * @interface: Pointer to the result
+ *
+ * The function gets phy interface string from property 'phy-mode' or
+ * 'phy-connection-type'. The index in phy_modes table is set in
+ * interface and 0 returned. In case of error interface is set to
+ * PHY_INTERFACE_MODE_NA and an errno is returned, e.g. -ENODEV.
+ */
+int of_get_phy_mode(struct device_node *np, phy_interface_t *interface)
+{
+	const char *pm;
+	int err, i;
+
+	*interface = PHY_INTERFACE_MODE_NA;
+
+	err = of_property_read_string(np, "phy-mode", &pm);
+	if (err < 0)
+		err = of_property_read_string(np, "phy-connection-type", &pm);
+	if (err < 0)
+		return err;
+
+	for (i = 0; i < PHY_INTERFACE_MODE_MAX; i++)
+		if (!strcasecmp(pm, phy_modes(i))) {
+			*interface = i;
+			return 0;
+		}
+
+	return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(of_get_phy_mode);
+
+static int of_get_mac_addr(struct device_node *np, const char *name, u8 *addr)
+{
+	struct property *pp = of_find_property(np, name, NULL);
+
+	if (pp && pp->length == ETH_ALEN && is_valid_ether_addr(pp->value)) {
+		memcpy(addr, pp->value, ETH_ALEN);
+		return 0;
+	}
+	return -ENODEV;
+}
+
+static int of_get_mac_addr_nvmem(struct device_node *np, u8 *addr)
+{
+	struct platform_device *pdev = of_find_device_by_node(np);
+	struct nvmem_cell *cell;
+	const void *mac;
+	size_t len;
+	int ret;
+
+	/* Try lookup by device first, there might be a nvmem_cell_lookup
+	 * associated with a given device.
+	 */
+	if (pdev) {
+		ret = nvmem_get_mac_address(&pdev->dev, addr);
+		put_device(&pdev->dev);
+		return ret;
+	}
+
+	cell = of_nvmem_cell_get(np, "mac-address");
+	if (IS_ERR(cell))
+		return PTR_ERR(cell);
+
+	mac = nvmem_cell_read(cell, &len);
+	nvmem_cell_put(cell);
+
+	if (IS_ERR(mac))
+		return PTR_ERR(mac);
+
+	if (len != ETH_ALEN || !is_valid_ether_addr(mac)) {
+		kfree(mac);
+		return -EINVAL;
+	}
+
+	memcpy(addr, mac, ETH_ALEN);
+	kfree(mac);
+
+	return 0;
+}
+
+/**
+ * of_get_mac_address()
+ * @np:		Caller's Device Node
+ * @addr:	Pointer to a six-byte array for the result
+ *
+ * Search the device tree for the best MAC address to use.  'mac-address' is
+ * checked first, because that is supposed to contain to "most recent" MAC
+ * address. If that isn't set, then 'local-mac-address' is checked next,
+ * because that is the default address. If that isn't set, then the obsolete
+ * 'address' is checked, just in case we're using an old device tree. If any
+ * of the above isn't set, then try to get MAC address from nvmem cell named
+ * 'mac-address'.
+ *
+ * Note that the 'address' property is supposed to contain a virtual address of
+ * the register set, but some DTS files have redefined that property to be the
+ * MAC address.
+ *
+ * All-zero MAC addresses are rejected, because those could be properties that
+ * exist in the device tree, but were not set by U-Boot.  For example, the
+ * DTS could define 'mac-address' and 'local-mac-address', with zero MAC
+ * addresses.  Some older U-Boots only initialized 'local-mac-address'.  In
+ * this case, the real MAC is in 'local-mac-address', and 'mac-address' exists
+ * but is all zeros.
+ *
+ * Return: 0 on success and errno in case of error.
+*/
+int of_get_mac_address(struct device_node *np, u8 *addr)
+{
+	int ret;
+
+	if (!np)
+		return -ENODEV;
+
+	ret = of_get_mac_addr(np, "mac-address", addr);
+	if (!ret)
+		return 0;
+
+	ret = of_get_mac_addr(np, "local-mac-address", addr);
+	if (!ret)
+		return 0;
+
+	ret = of_get_mac_addr(np, "address", addr);
+	if (!ret)
+		return 0;
+
+	return of_get_mac_addr_nvmem(np, addr);
+}
+EXPORT_SYMBOL(of_get_mac_address);
+
+/**
+ * of_get_ethdev_address()
+ * @np:		Caller's Device Node
+ * @dev:	Pointer to netdevice which address will be updated
+ *
+ * Search the device tree for the best MAC address to use.
+ * If found set @dev->dev_addr to that address.
+ *
+ * See documentation of of_get_mac_address() for more information on how
+ * the best address is determined.
+ *
+ * Return: 0 on success and errno in case of error.
+ */
+int of_get_ethdev_address(struct device_node *np, struct net_device *dev)
+{
+	u8 addr[ETH_ALEN];
+	int ret;
+
+	ret = of_get_mac_address(np, addr);
+	if (!ret)
+		eth_hw_addr_set(dev, addr);
+	return ret;
+}
+EXPORT_SYMBOL(of_get_ethdev_address);
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/page_pool.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/page_pool.c
@@ -26,6 +26,29 @@
 
 #define BIAS_MAX	LONG_MAX
 
+static bool page_pool_producer_lock(struct page_pool *pool)
+	__acquires(&pool->ring.producer_lock)
+{
+	bool in_softirq = in_softirq();
+
+	if (in_softirq)
+		spin_lock(&pool->ring.producer_lock);
+	else
+		spin_lock_bh(&pool->ring.producer_lock);
+
+	return in_softirq;
+}
+
+static void page_pool_producer_unlock(struct page_pool *pool,
+				      bool in_softirq)
+	__releases(&pool->ring.producer_lock)
+{
+	if (in_softirq)
+		spin_unlock(&pool->ring.producer_lock);
+	else
+		spin_unlock_bh(&pool->ring.producer_lock);
+}
+
 static int page_pool_init(struct page_pool *pool,
 			  const struct page_pool_params *params)
 {
@@ -390,8 +413,8 @@
 static bool page_pool_recycle_in_ring(struct page_pool *pool, struct page *page)
 {
 	int ret;
-	/* BH protection not needed if current is serving softirq */
-	if (in_serving_softirq())
+	/* BH protection not needed if current is softirq */
+	if (in_softirq())
 		ret = ptr_ring_produce(&pool->ring, page);
 	else
 		ret = ptr_ring_produce_bh(&pool->ring, page);
@@ -446,7 +469,7 @@
 			page_pool_dma_sync_for_device(pool, page,
 						      dma_sync_size);
 
-		if (allow_direct && in_serving_softirq() &&
+		if (allow_direct && in_softirq() &&
 		    page_pool_recycle_in_cache(page, pool))
 			return NULL;
 
@@ -489,6 +512,7 @@
 			     int count)
 {
 	int i, bulk_len = 0;
+	bool in_softirq;
 
 	for (i = 0; i < count; i++) {
 		struct page *page = virt_to_head_page(data[i]);
@@ -503,12 +527,12 @@
 		return;
 
 	/* Bulk producer into ptr_ring page_pool cache */
-	page_pool_ring_lock(pool);
+	in_softirq = page_pool_producer_lock(pool);
 	for (i = 0; i < bulk_len; i++) {
 		if (__ptr_ring_produce(&pool->ring, data[i]))
 			break; /* ring full */
 	}
-	page_pool_ring_unlock(pool);
+	page_pool_producer_unlock(pool, in_softirq);
 
 	/* Hopefully all pages was return into ptr_ring */
 	if (likely(i == bulk_len))
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/pktgen.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/pktgen.c
@@ -668,19 +668,19 @@
 	seq_puts(seq, "     Flags: ");
 
 	for (i = 0; i < NR_PKT_FLAGS; i++) {
-		if (i == F_FLOW_SEQ)
+		if (i == FLOW_SEQ_SHIFT)
 			if (!pkt_dev->cflows)
 				continue;
 
-		if (pkt_dev->flags & (1 << i))
+		if (pkt_dev->flags & (1 << i)) {
 			seq_printf(seq, "%s  ", pkt_flag_names[i]);
-		else if (i == F_FLOW_SEQ)
-			seq_puts(seq, "FLOW_RND  ");
-
 #ifdef CONFIG_XFRM
-		if (i == F_IPSEC && pkt_dev->spi)
-			seq_printf(seq, "spi:%u", pkt_dev->spi);
+			if (i == IPSEC_SHIFT && pkt_dev->spi)
+				seq_printf(seq, "spi:%u  ", pkt_dev->spi);
 #endif
+		} else if (i == FLOW_SEQ_SHIFT) {
+			seq_puts(seq, "FLOW_RND  ");
+		}
 	}
 
 	seq_puts(seq, "\n");
@@ -849,6 +849,9 @@
 		unsigned long weight;
 		unsigned long size;
 
+		if (pkt_dev->n_imix_entries >= MAX_IMIX_ENTRIES)
+			return -E2BIG;
+
 		len = num_arg(&buffer[i], max_digits, &size);
 		if (len < 0)
 			return len;
@@ -878,9 +881,6 @@
 
 		i++;
 		pkt_dev->n_imix_entries++;
-
-		if (pkt_dev->n_imix_entries > MAX_IMIX_ENTRIES)
-			return -E2BIG;
 	} while (c == ' ');
 
 	return i;
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/request_sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/request_sock.c
@@ -33,9 +33,6 @@
 
 void reqsk_queue_alloc(struct request_sock_queue *queue)
 {
-	spin_lock_init(&queue->rskq_lock);
-
-	spin_lock_init(&queue->fastopenq.lock);
 	queue->fastopenq.rskq_rst_head = NULL;
 	queue->fastopenq.rskq_rst_tail = NULL;
 	queue->fastopenq.qlen = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/rtnetlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/rtnetlink.c
@@ -348,6 +348,35 @@
 }
 EXPORT_SYMBOL_GPL(rtnl_unregister_all);
 
+int __rtnl_register_many(const struct rtnl_msg_handler *handlers, int n)
+{
+	const struct rtnl_msg_handler *handler;
+	int i, err;
+
+	for (i = 0, handler = handlers; i < n; i++, handler++) {
+		err = rtnl_register_internal(handler->owner, handler->protocol,
+					     handler->msgtype, handler->doit,
+					     handler->dumpit, handler->flags);
+		if (err) {
+			__rtnl_unregister_many(handlers, i);
+			break;
+		}
+	}
+
+	return err;
+}
+EXPORT_SYMBOL_GPL(__rtnl_register_many);
+
+void __rtnl_unregister_many(const struct rtnl_msg_handler *handlers, int n)
+{
+	const struct rtnl_msg_handler *handler;
+	int i;
+
+	for (i = n - 1, handler = handlers + n - 1; i >= 0; i--, handler--)
+		rtnl_unregister(handler->protocol, handler->msgtype);
+}
+EXPORT_SYMBOL_GPL(__rtnl_unregister_many);
+
 static LIST_HEAD(link_ops);
 
 static const struct rtnl_link_ops *rtnl_link_ops_get(const char *kind)
@@ -842,9 +871,9 @@
 	}
 
 	if (dev->operstate != operstate) {
-		write_lock_bh(&dev_base_lock);
+		write_lock(&dev_base_lock);
 		dev->operstate = operstate;
-		write_unlock_bh(&dev_base_lock);
+		write_unlock(&dev_base_lock);
 		netdev_state_change(dev);
 	}
 }
@@ -922,24 +951,30 @@
 			 nla_total_size(sizeof(struct ifla_vf_rate)) +
 			 nla_total_size(sizeof(struct ifla_vf_link_state)) +
 			 nla_total_size(sizeof(struct ifla_vf_rss_query_en)) +
-			 nla_total_size(0) + /* nest IFLA_VF_STATS */
-			 /* IFLA_VF_STATS_RX_PACKETS */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_TX_PACKETS */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_RX_BYTES */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_TX_BYTES */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_BROADCAST */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_MULTICAST */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_RX_DROPPED */
-			 nla_total_size_64bit(sizeof(__u64)) +
-			 /* IFLA_VF_STATS_TX_DROPPED */
-			 nla_total_size_64bit(sizeof(__u64)) +
 			 nla_total_size(sizeof(struct ifla_vf_trust)));
+		if (~ext_filter_mask & RTEXT_FILTER_SKIP_STATS) {
+			size += num_vfs *
+				(nla_total_size(0) + /* nest IFLA_VF_STATS */
+				 /* IFLA_VF_STATS_RX_PACKETS */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_TX_PACKETS */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_RX_BYTES */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_TX_BYTES */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_BROADCAST */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_MULTICAST */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_RX_DROPPED */
+				 nla_total_size_64bit(sizeof(__u64)) +
+				 /* IFLA_VF_STATS_TX_DROPPED */
+				 nla_total_size_64bit(sizeof(__u64)));
+		}
+		if (dev->netdev_ops->ndo_get_vf_guid)
+			size += num_vfs * 2 *
+				nla_total_size(sizeof(struct ifla_vf_guid));
 		return size;
 	} else
 		return 0;
@@ -1214,7 +1249,8 @@
 static noinline_for_stack int rtnl_fill_vfinfo(struct sk_buff *skb,
 					       struct net_device *dev,
 					       int vfs_num,
-					       struct nlattr *vfinfo)
+					       struct nlattr *vfinfo,
+					       u32 ext_filter_mask)
 {
 	struct ifla_vf_rss_query_en vf_rss_query_en;
 	struct nlattr *vf, *vfstats, *vfvlanlist;
@@ -1320,33 +1356,35 @@
 		goto nla_put_vf_failure;
 	}
 	nla_nest_end(skb, vfvlanlist);
-	memset(&vf_stats, 0, sizeof(vf_stats));
-	if (dev->netdev_ops->ndo_get_vf_stats)
-		dev->netdev_ops->ndo_get_vf_stats(dev, vfs_num,
-						&vf_stats);
-	vfstats = nla_nest_start_noflag(skb, IFLA_VF_STATS);
-	if (!vfstats)
-		goto nla_put_vf_failure;
-	if (nla_put_u64_64bit(skb, IFLA_VF_STATS_RX_PACKETS,
-			      vf_stats.rx_packets, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_TX_PACKETS,
-			      vf_stats.tx_packets, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_RX_BYTES,
-			      vf_stats.rx_bytes, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_TX_BYTES,
-			      vf_stats.tx_bytes, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_BROADCAST,
-			      vf_stats.broadcast, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_MULTICAST,
-			      vf_stats.multicast, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_RX_DROPPED,
-			      vf_stats.rx_dropped, IFLA_VF_STATS_PAD) ||
-	    nla_put_u64_64bit(skb, IFLA_VF_STATS_TX_DROPPED,
-			      vf_stats.tx_dropped, IFLA_VF_STATS_PAD)) {
-		nla_nest_cancel(skb, vfstats);
-		goto nla_put_vf_failure;
+	if (~ext_filter_mask & RTEXT_FILTER_SKIP_STATS) {
+		memset(&vf_stats, 0, sizeof(vf_stats));
+		if (dev->netdev_ops->ndo_get_vf_stats)
+			dev->netdev_ops->ndo_get_vf_stats(dev, vfs_num,
+							  &vf_stats);
+		vfstats = nla_nest_start_noflag(skb, IFLA_VF_STATS);
+		if (!vfstats)
+			goto nla_put_vf_failure;
+		if (nla_put_u64_64bit(skb, IFLA_VF_STATS_RX_PACKETS,
+				      vf_stats.rx_packets, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_TX_PACKETS,
+				      vf_stats.tx_packets, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_RX_BYTES,
+				      vf_stats.rx_bytes, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_TX_BYTES,
+				      vf_stats.tx_bytes, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_BROADCAST,
+				      vf_stats.broadcast, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_MULTICAST,
+				      vf_stats.multicast, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_RX_DROPPED,
+				      vf_stats.rx_dropped, IFLA_VF_STATS_PAD) ||
+		    nla_put_u64_64bit(skb, IFLA_VF_STATS_TX_DROPPED,
+				      vf_stats.tx_dropped, IFLA_VF_STATS_PAD)) {
+			nla_nest_cancel(skb, vfstats);
+			goto nla_put_vf_failure;
+		}
+		nla_nest_end(skb, vfstats);
 	}
-	nla_nest_end(skb, vfstats);
 	nla_nest_end(skb, vf);
 	return 0;
 
@@ -1379,7 +1417,7 @@
 		return -EMSGSIZE;
 
 	for (i = 0; i < num_vfs; i++) {
-		if (rtnl_fill_vfinfo(skb, dev, i, vfinfo))
+		if (rtnl_fill_vfinfo(skb, dev, i, vfinfo, ext_filter_mask))
 			return -EMSGSIZE;
 	}
 
@@ -1698,6 +1736,7 @@
 {
 	struct ifinfomsg *ifm;
 	struct nlmsghdr *nlh;
+	struct Qdisc *qdisc;
 
 	ASSERT_RTNL();
 	nlh = nlmsg_put(skb, pid, seq, type, sizeof(*ifm), flags);
@@ -1715,6 +1754,7 @@
 	if (tgt_netnsid >= 0 && nla_put_s32(skb, IFLA_TARGET_NETNSID, tgt_netnsid))
 		goto nla_put_failure;
 
+	qdisc = rtnl_dereference(dev->qdisc);
 	if (nla_put_string(skb, IFLA_IFNAME, dev->name) ||
 	    nla_put_u32(skb, IFLA_TXQLEN, dev->tx_queue_len) ||
 	    nla_put_u8(skb, IFLA_OPERSTATE,
@@ -1733,8 +1773,8 @@
 #endif
 	    put_master_ifindex(skb, dev) ||
 	    nla_put_u8(skb, IFLA_CARRIER, netif_carrier_ok(dev)) ||
-	    (dev->qdisc &&
-	     nla_put_string(skb, IFLA_QDISC, dev->qdisc->ops->id)) ||
+	    (qdisc &&
+	     nla_put_string(skb, IFLA_QDISC, qdisc->ops->id)) ||
 	    nla_put_ifalias(skb, dev) ||
 	    nla_put_u32(skb, IFLA_CARRIER_CHANGES,
 			atomic_read(&dev->carrier_up_count) +
@@ -2165,13 +2205,27 @@
 	return err;
 }
 
-int rtnl_nla_parse_ifla(struct nlattr **tb, const struct nlattr *head, int len,
-			struct netlink_ext_ack *exterr)
+int rtnl_nla_parse_ifinfomsg(struct nlattr **tb, const struct nlattr *nla_peer,
+			     struct netlink_ext_ack *exterr)
 {
-	return nla_parse_deprecated(tb, IFLA_MAX, head, len, ifla_policy,
+	const struct ifinfomsg *ifmp;
+	const struct nlattr *attrs;
+	size_t len;
+
+	ifmp = nla_data(nla_peer);
+	attrs = nla_data(nla_peer) + sizeof(struct ifinfomsg);
+	len = nla_len(nla_peer) - sizeof(struct ifinfomsg);
+
+	if (ifmp->ifi_index < 0) {
+		NL_SET_ERR_MSG_ATTR(exterr, nla_peer,
+				    "ifindex can't be negative");
+		return -EINVAL;
+	}
+
+	return nla_parse_deprecated(tb, IFLA_MAX, attrs, len, ifla_policy,
 				    exterr);
 }
-EXPORT_SYMBOL(rtnl_nla_parse_ifla);
+EXPORT_SYMBOL(rtnl_nla_parse_ifinfomsg);
 
 struct net *rtnl_link_get_net(struct net *src_net, struct nlattr *tb[])
 {
@@ -2361,7 +2415,7 @@
 
 		nla_for_each_nested(attr, tb[IFLA_VF_VLAN_LIST], rem) {
 			if (nla_type(attr) != IFLA_VF_VLAN_INFO ||
-			    nla_len(attr) < NLA_HDRLEN) {
+			    nla_len(attr) < sizeof(struct ifla_vf_vlan_info)) {
 				return -EINVAL;
 			}
 			if (len >= MAX_VLAN_LIST_LEN)
@@ -2595,17 +2649,23 @@
 static int do_setlink(const struct sk_buff *skb,
 		      struct net_device *dev, struct ifinfomsg *ifm,
 		      struct netlink_ext_ack *extack,
-		      struct nlattr **tb, char *ifname, int status)
+		      struct nlattr **tb, int status)
 {
 	const struct net_device_ops *ops = dev->netdev_ops;
+	char ifname[IFNAMSIZ];
 	int err;
 
 	err = validate_linkmsg(dev, tb, extack);
 	if (err < 0)
 		return err;
 
+	if (tb[IFLA_IFNAME])
+		nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
+	else
+		ifname[0] = '\0';
+
 	if (tb[IFLA_NET_NS_PID] || tb[IFLA_NET_NS_FD] || tb[IFLA_TARGET_NETNSID]) {
-		const char *pat = ifname && ifname[0] ? ifname : NULL;
+		const char *pat = ifname[0] ? ifname : NULL;
 		struct net *net;
 		int new_ifindex;
 
@@ -2779,11 +2839,11 @@
 	if (tb[IFLA_LINKMODE]) {
 		unsigned char value = nla_get_u8(tb[IFLA_LINKMODE]);
 
-		write_lock_bh(&dev_base_lock);
+		write_lock(&dev_base_lock);
 		if (dev->link_mode ^ value)
 			status |= DO_SETLINK_NOTIFY;
 		dev->link_mode = value;
-		write_unlock_bh(&dev_base_lock);
+		write_unlock(&dev_base_lock);
 	}
 
 	if (tb[IFLA_VFINFO_LIST]) {
@@ -2952,21 +3012,16 @@
 }
 
 static struct net_device *rtnl_dev_get(struct net *net,
-				       struct nlattr *ifname_attr,
-				       struct nlattr *altifname_attr,
-				       char *ifname)
-{
-	char buffer[ALTIFNAMSIZ];
-
-	if (!ifname) {
-		ifname = buffer;
-		if (ifname_attr)
-			nla_strscpy(ifname, ifname_attr, IFNAMSIZ);
-		else if (altifname_attr)
-			nla_strscpy(ifname, altifname_attr, ALTIFNAMSIZ);
-		else
-			return NULL;
-	}
+				       struct nlattr *tb[])
+{
+	char ifname[ALTIFNAMSIZ];
+
+	if (tb[IFLA_IFNAME])
+		nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
+	else if (tb[IFLA_ALT_IFNAME])
+		nla_strscpy(ifname, tb[IFLA_ALT_IFNAME], ALTIFNAMSIZ);
+	else
+		return NULL;
 
 	return __dev_get_by_name(net, ifname);
 }
@@ -2979,7 +3034,6 @@
 	struct net_device *dev;
 	int err;
 	struct nlattr *tb[IFLA_MAX+1];
-	char ifname[IFNAMSIZ];
 
 	err = nlmsg_parse_deprecated(nlh, sizeof(*ifm), tb, IFLA_MAX,
 				     ifla_policy, extack);
@@ -2990,17 +3044,12 @@
 	if (err < 0)
 		goto errout;
 
-	if (tb[IFLA_IFNAME])
-		nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
-	else
-		ifname[0] = '\0';
-
 	err = -EINVAL;
 	ifm = nlmsg_data(nlh);
 	if (ifm->ifi_index > 0)
 		dev = __dev_get_by_index(net, ifm->ifi_index);
 	else if (tb[IFLA_IFNAME] || tb[IFLA_ALT_IFNAME])
-		dev = rtnl_dev_get(net, NULL, tb[IFLA_ALT_IFNAME], ifname);
+		dev = rtnl_dev_get(net, tb);
 	else
 		goto errout;
 
@@ -3009,7 +3058,7 @@
 		goto errout;
 	}
 
-	err = do_setlink(skb, dev, ifm, extack, tb, ifname, 0);
+	err = do_setlink(skb, dev, ifm, extack, tb, 0);
 errout:
 	return err;
 }
@@ -3098,8 +3147,7 @@
 	if (ifm->ifi_index > 0)
 		dev = __dev_get_by_index(tgt_net, ifm->ifi_index);
 	else if (tb[IFLA_IFNAME] || tb[IFLA_ALT_IFNAME])
-		dev = rtnl_dev_get(net, tb[IFLA_IFNAME],
-				   tb[IFLA_ALT_IFNAME], NULL);
+		dev = rtnl_dev_get(tgt_net, tb);
 	else if (tb[IFLA_GROUP])
 		err = rtnl_group_dellink(tgt_net, nla_get_u32(tb[IFLA_GROUP]));
 	else
@@ -3153,6 +3201,7 @@
 	struct net_device *dev;
 	unsigned int num_tx_queues = 1;
 	unsigned int num_rx_queues = 1;
+	int err;
 
 	if (tb[IFLA_NUM_TX_QUEUES])
 		num_tx_queues = nla_get_u32(tb[IFLA_NUM_TX_QUEUES]);
@@ -3188,13 +3237,18 @@
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
 
+	err = validate_linkmsg(dev, tb, extack);
+	if (err < 0) {
+		free_netdev(dev);
+		return ERR_PTR(err);
+	}
+
 	dev_net_set(dev, net);
 	dev->rtnl_link_ops = ops;
 	dev->rtnl_link_state = RTNL_LINK_INITIALIZING;
 
 	if (tb[IFLA_MTU]) {
 		u32 mtu = nla_get_u32(tb[IFLA_MTU]);
-		int err;
 
 		err = dev_validate_mtu(dev, mtu, extack);
 		if (err) {
@@ -3239,7 +3293,7 @@
 
 	for_each_netdev_safe(net, dev, aux) {
 		if (dev->group == group) {
-			err = do_setlink(skb, dev, ifm, extack, tb, NULL, 0);
+			err = do_setlink(skb, dev, ifm, extack, tb, 0);
 			if (err < 0)
 				return err;
 		}
@@ -3254,8 +3308,8 @@
 	struct nlattr *slave_attr[RTNL_SLAVE_MAX_TYPE + 1];
 	unsigned char name_assign_type = NET_NAME_USER;
 	struct nlattr *linkinfo[IFLA_INFO_MAX + 1];
-	const struct rtnl_link_ops *m_ops = NULL;
-	struct net_device *master_dev = NULL;
+	const struct rtnl_link_ops *m_ops;
+	struct net_device *master_dev;
 	struct net *net = sock_net(skb->sk);
 	const struct rtnl_link_ops *ops;
 	struct nlattr *tb[IFLA_MAX + 1];
@@ -3266,6 +3320,7 @@
 	struct ifinfomsg *ifm;
 	char ifname[IFNAMSIZ];
 	struct nlattr **data;
+	bool link_specified;
 	int err;
 
 #ifdef CONFIG_MODULES
@@ -3280,19 +3335,23 @@
 	if (err < 0)
 		return err;
 
-	if (tb[IFLA_IFNAME])
-		nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
-	else
-		ifname[0] = '\0';
-
 	ifm = nlmsg_data(nlh);
-	if (ifm->ifi_index > 0)
+	if (ifm->ifi_index > 0) {
+		link_specified = true;
 		dev = __dev_get_by_index(net, ifm->ifi_index);
-	else if (tb[IFLA_IFNAME] || tb[IFLA_ALT_IFNAME])
-		dev = rtnl_dev_get(net, NULL, tb[IFLA_ALT_IFNAME], ifname);
-	else
+	} else if (ifm->ifi_index < 0) {
+		NL_SET_ERR_MSG(extack, "ifindex can't be negative");
+		return -EINVAL;
+	} else if (tb[IFLA_IFNAME] || tb[IFLA_ALT_IFNAME]) {
+		link_specified = true;
+		dev = rtnl_dev_get(net, tb);
+	} else {
+		link_specified = false;
 		dev = NULL;
+	}
 
+	master_dev = NULL;
+	m_ops = NULL;
 	if (dev) {
 		master_dev = netdev_master_upper_dev_get(dev);
 		if (master_dev)
@@ -3388,11 +3447,16 @@
 			status |= DO_SETLINK_NOTIFY;
 		}
 
-		return do_setlink(skb, dev, ifm, extack, tb, ifname, status);
+		return do_setlink(skb, dev, ifm, extack, tb, status);
 	}
 
 	if (!(nlh->nlmsg_flags & NLM_F_CREATE)) {
-		if (ifm->ifi_index == 0 && tb[IFLA_GROUP])
+		/* No dev found and NLM_F_CREATE not set. Requested dev does not exist,
+		 * or it's for a group
+		*/
+		if (link_specified)
+			return -ENODEV;
+		if (tb[IFLA_GROUP])
 			return rtnl_group_changelink(skb, net,
 						nla_get_u32(tb[IFLA_GROUP]),
 						ifm, extack, tb);
@@ -3420,7 +3484,9 @@
 	if (!ops->alloc && !ops->setup)
 		return -EOPNOTSUPP;
 
-	if (!ifname[0]) {
+	if (tb[IFLA_IFNAME]) {
+		nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
+	} else {
 		snprintf(ifname, IFNAMSIZ, "%s%%d", ops->kind);
 		name_assign_type = NET_NAME_ENUM;
 	}
@@ -3592,8 +3658,7 @@
 	if (ifm->ifi_index > 0)
 		dev = __dev_get_by_index(tgt_net, ifm->ifi_index);
 	else if (tb[IFLA_IFNAME] || tb[IFLA_ALT_IFNAME])
-		dev = rtnl_dev_get(tgt_net, tb[IFLA_IFNAME],
-				   tb[IFLA_ALT_IFNAME], NULL);
+		dev = rtnl_dev_get(tgt_net, tb);
 	else
 		goto out;
 
@@ -3627,13 +3692,24 @@
 			   bool *changed, struct netlink_ext_ack *extack)
 {
 	char *alt_ifname;
+	size_t size;
 	int err;
 
 	err = nla_validate(attr, attr->nla_len, IFLA_MAX, ifla_policy, extack);
 	if (err)
 		return err;
 
-	alt_ifname = nla_strdup(attr, GFP_KERNEL);
+	if (cmd == RTM_NEWLINKPROP) {
+		size = rtnl_prop_list_size(dev);
+		size += nla_total_size(ALTIFNAMSIZ);
+		if (size >= U16_MAX) {
+			NL_SET_ERR_MSG(extack,
+				       "effective property list too long");
+			return -EINVAL;
+		}
+	}
+
+	alt_ifname = nla_strdup(attr, GFP_KERNEL_ACCOUNT);
 	if (!alt_ifname)
 		return -ENOMEM;
 
@@ -3677,8 +3753,7 @@
 	if (ifm->ifi_index > 0)
 		dev = __dev_get_by_index(net, ifm->ifi_index);
 	else if (tb[IFLA_IFNAME] || tb[IFLA_ALT_IFNAME])
-		dev = rtnl_dev_get(net, tb[IFLA_IFNAME],
-				   tb[IFLA_ALT_IFNAME], NULL);
+		dev = rtnl_dev_get(net, tb);
 	else
 		return -EINVAL;
 
@@ -3884,7 +3959,7 @@
 	ndm->ndm_ifindex = dev->ifindex;
 	ndm->ndm_state   = ndm_state;
 
-	if (nla_put(skb, NDA_LLADDR, ETH_ALEN, addr))
+	if (nla_put(skb, NDA_LLADDR, dev->addr_len, addr))
 		goto nla_put_failure;
 	if (vid)
 		if (nla_put(skb, NDA_VLAN, sizeof(u16), &vid))
@@ -3898,10 +3973,10 @@
 	return -EMSGSIZE;
 }
 
-static inline size_t rtnl_fdb_nlmsg_size(void)
+static inline size_t rtnl_fdb_nlmsg_size(const struct net_device *dev)
 {
 	return NLMSG_ALIGN(sizeof(struct ndmsg)) +
-	       nla_total_size(ETH_ALEN) +	/* NDA_LLADDR */
+	       nla_total_size(dev->addr_len) +	/* NDA_LLADDR */
 	       nla_total_size(sizeof(u16)) +	/* NDA_VLAN */
 	       0;
 }
@@ -3913,7 +3988,7 @@
 	struct sk_buff *skb;
 	int err = -ENOBUFS;
 
-	skb = nlmsg_new(rtnl_fdb_nlmsg_size(), GFP_ATOMIC);
+	skb = nlmsg_new(rtnl_fdb_nlmsg_size(dev), GFP_ATOMIC);
 	if (!skb)
 		goto errout;
 
@@ -4871,10 +4946,9 @@
 	struct net *net = sock_net(skb->sk);
 	struct ifinfomsg *ifm;
 	struct net_device *dev;
-	struct nlattr *br_spec, *attr = NULL;
+	struct nlattr *br_spec, *attr, *br_flags_attr = NULL;
 	int rem, err = -EOPNOTSUPP;
 	u16 flags = 0;
-	bool have_flags = false;
 
 	if (nlmsg_len(nlh) < sizeof(*ifm))
 		return -EINVAL;
@@ -4892,13 +4966,17 @@
 	br_spec = nlmsg_find_attr(nlh, sizeof(struct ifinfomsg), IFLA_AF_SPEC);
 	if (br_spec) {
 		nla_for_each_nested(attr, br_spec, rem) {
-			if (nla_type(attr) == IFLA_BRIDGE_FLAGS) {
+			if (nla_type(attr) == IFLA_BRIDGE_FLAGS && !br_flags_attr) {
 				if (nla_len(attr) < sizeof(flags))
 					return -EINVAL;
 
-				have_flags = true;
+				br_flags_attr = attr;
 				flags = nla_get_u16(attr);
-				break;
+			}
+
+			if (nla_type(attr) == IFLA_BRIDGE_MODE) {
+				if (nla_len(attr) < sizeof(u16))
+					return -EINVAL;
 			}
 		}
 	}
@@ -4936,8 +5014,8 @@
 		}
 	}
 
-	if (have_flags)
-		memcpy(nla_data(attr), &flags, sizeof(flags));
+	if (br_flags_attr)
+		memcpy(nla_data(br_flags_attr), &flags, sizeof(flags));
 out:
 	return err;
 }
@@ -5475,11 +5553,11 @@
 {
 	struct net *net = sock_net(skb->sk);
 	struct rtnl_link *link;
+	enum rtnl_kinds kind;
 	struct module *owner;
 	int err = -EOPNOTSUPP;
 	rtnl_doit_func doit;
 	unsigned int flags;
-	int kind;
 	int family;
 	int type;
 
@@ -5496,11 +5574,11 @@
 	family = ((struct rtgenmsg *)nlmsg_data(nlh))->rtgen_family;
 	kind = type&3;
 
-	if (kind != 2 && !netlink_net_capable(skb, CAP_NET_ADMIN))
+	if (kind != RTNL_KIND_GET && !netlink_net_capable(skb, CAP_NET_ADMIN))
 		return -EPERM;
 
 	rcu_read_lock();
-	if (kind == 2 && nlh->nlmsg_flags&NLM_F_DUMP) {
+	if (kind == RTNL_KIND_GET && (nlh->nlmsg_flags & NLM_F_DUMP)) {
 		struct sock *rtnl;
 		rtnl_dumpit_func dumpit;
 		u32 min_dump_alloc = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/scm.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/scm.c
@@ -26,6 +26,7 @@
 #include <linux/nsproxy.h>
 #include <linux/slab.h>
 #include <linux/errqueue.h>
+#include <linux/io_uring.h>
 
 #include <linux/uaccess.h>
 
@@ -103,6 +104,11 @@
 
 		if (fd < 0 || !(file = fget_raw(fd)))
 			return -EBADF;
+		/* don't allow io_uring files */
+		if (io_is_uring_fops(file)) {
+			fput(file);
+			return -EINVAL;
+		}
 		*fpp++ = file;
 		fpl->count++;
 	}
@@ -229,6 +235,8 @@
 	if (msg->msg_control_is_user) {
 		struct cmsghdr __user *cm = msg->msg_control_user;
 
+		check_object_size(data, cmlen - sizeof(*cm), true);
+
 		if (!user_write_access_begin(cm, cmlen))
 			goto efault;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/secure_seq.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/secure_seq.c
@@ -22,6 +22,8 @@
 static siphash_key_t net_secret __read_mostly;
 static siphash_key_t ts_secret __read_mostly;
 
+#define EPHEMERAL_PORT_SHUFFLE_PERIOD (10 * HZ)
+
 static __always_inline void net_secret_init(void)
 {
 	net_get_random_once(&net_secret, sizeof(net_secret));
@@ -62,7 +64,7 @@
 		.daddr = *(struct in6_addr *)daddr,
 	};
 
-	if (net->ipv4.sysctl_tcp_timestamps != 1)
+	if (READ_ONCE(net->ipv4.sysctl_tcp_timestamps) != 1)
 		return 0;
 
 	ts_secret_init();
@@ -94,17 +96,19 @@
 }
 EXPORT_SYMBOL(secure_tcpv6_seq);
 
-u32 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr,
+u64 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr,
 			       __be16 dport)
 {
 	const struct {
 		struct in6_addr saddr;
 		struct in6_addr daddr;
+		unsigned int timeseed;
 		__be16 dport;
 	} __aligned(SIPHASH_ALIGNMENT) combined = {
 		.saddr = *(struct in6_addr *)saddr,
 		.daddr = *(struct in6_addr *)daddr,
-		.dport = dport
+		.timeseed = jiffies / EPHEMERAL_PORT_SHUFFLE_PERIOD,
+		.dport = dport,
 	};
 	net_secret_init();
 	return siphash(&combined, offsetofend(typeof(combined), dport),
@@ -116,7 +120,7 @@
 #ifdef CONFIG_INET
 u32 secure_tcp_ts_off(const struct net *net, __be32 saddr, __be32 daddr)
 {
-	if (net->ipv4.sysctl_tcp_timestamps != 1)
+	if (READ_ONCE(net->ipv4.sysctl_tcp_timestamps) != 1)
 		return 0;
 
 	ts_secret_init();
@@ -142,11 +146,13 @@
 }
 EXPORT_SYMBOL_GPL(secure_tcp_seq);
 
-u32 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport)
+u64 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport)
 {
 	net_secret_init();
-	return siphash_3u32((__force u32)saddr, (__force u32)daddr,
-			    (__force u16)dport, &net_secret);
+	return siphash_4u32((__force u32)saddr, (__force u32)daddr,
+			    (__force u16)dport,
+			    jiffies / EPHEMERAL_PORT_SHUFFLE_PERIOD,
+			    &net_secret);
 }
 EXPORT_SYMBOL_GPL(secure_ipv4_port_ephemeral);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/skbuff.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/skbuff.c
@@ -203,7 +203,7 @@
 	skb->head = data;
 	skb->data = data;
 	skb_reset_tail_pointer(skb);
-	skb->end = skb->tail + size;
+	skb_set_end_offset(skb, size);
 	skb->mac_header = (typeof(skb->mac_header))~0U;
 	skb->transport_header = (typeof(skb->transport_header))~0U;
 
@@ -759,21 +759,23 @@
 EXPORT_SYMBOL(__kfree_skb);
 
 /**
- *	kfree_skb - free an sk_buff
+ *	kfree_skb_reason - free an sk_buff with special reason
  *	@skb: buffer to free
+ *	@reason: reason why this skb is dropped
  *
  *	Drop a reference to the buffer and free it if the usage count has
- *	hit zero.
+ *	hit zero. Meanwhile, pass the drop reason to 'kfree_skb'
+ *	tracepoint.
  */
-void kfree_skb(struct sk_buff *skb)
+void kfree_skb_reason(struct sk_buff *skb, enum skb_drop_reason reason)
 {
 	if (!skb_unref(skb))
 		return;
 
-	trace_kfree_skb(skb, __builtin_return_address(0));
+	trace_kfree_skb(skb, __builtin_return_address(0), reason);
 	__kfree_skb(skb);
 }
-EXPORT_SYMBOL(kfree_skb);
+EXPORT_SYMBOL(kfree_skb_reason);
 
 void kfree_skb_list(struct sk_buff *segs)
 {
@@ -832,7 +834,7 @@
 	       ntohs(skb->protocol), skb->pkt_type, skb->skb_iif);
 
 	if (dev)
-		printk("%sdev name=%s feat=0x%pNF\n",
+		printk("%sdev name=%s feat=%pNF\n",
 		       level, dev->name, &dev->features);
 	if (sk)
 		printk("%ssk family=%hu type=%u proto=%u\n",
@@ -1581,11 +1583,17 @@
 
 struct sk_buff *skb_copy(const struct sk_buff *skb, gfp_t gfp_mask)
 {
-	int headerlen = skb_headroom(skb);
-	unsigned int size = skb_end_offset(skb) + skb->data_len;
-	struct sk_buff *n = __alloc_skb(size, gfp_mask,
-					skb_alloc_rx_flag(skb), NUMA_NO_NODE);
+	struct sk_buff *n;
+	unsigned int size;
+	int headerlen;
+
+	if (WARN_ON_ONCE(skb_shinfo(skb)->gso_type & SKB_GSO_FRAGLIST))
+		return NULL;
 
+	headerlen = skb_headroom(skb);
+	size = skb_end_offset(skb) + skb->data_len;
+	n = __alloc_skb(size, gfp_mask,
+			skb_alloc_rx_flag(skb), NUMA_NO_NODE);
 	if (!n)
 		return NULL;
 
@@ -1738,11 +1746,10 @@
 	skb->head     = data;
 	skb->head_frag = 0;
 	skb->data    += off;
+
+	skb_set_end_offset(skb, size);
 #ifdef NET_SKBUFF_DATA_USES_OFFSET
-	skb->end      = size;
 	off           = nhead;
-#else
-	skb->end      = skb->head + size;
 #endif
 	skb->tail	      += off;
 	skb_headers_offset_update(skb, nhead);
@@ -1790,6 +1797,38 @@
 }
 EXPORT_SYMBOL(skb_realloc_headroom);
 
+int __skb_unclone_keeptruesize(struct sk_buff *skb, gfp_t pri)
+{
+	unsigned int saved_end_offset, saved_truesize;
+	struct skb_shared_info *shinfo;
+	int res;
+
+	saved_end_offset = skb_end_offset(skb);
+	saved_truesize = skb->truesize;
+
+	res = pskb_expand_head(skb, 0, 0, pri);
+	if (res)
+		return res;
+
+	skb->truesize = saved_truesize;
+
+	if (likely(skb_end_offset(skb) == saved_end_offset))
+		return 0;
+
+	shinfo = skb_shinfo(skb);
+
+	/* We are about to change back skb->end,
+	 * we need to move skb_shinfo() to its new location.
+	 */
+	memmove(skb->head + saved_end_offset,
+		shinfo,
+		offsetof(struct skb_shared_info, frags[shinfo->nr_frags]));
+
+	skb_set_end_offset(skb, saved_end_offset);
+
+	return 0;
+}
+
 /**
  *	skb_expand_head - reallocate header of &sk_buff
  *	@skb: buffer to reallocate
@@ -1866,12 +1905,17 @@
 	/*
 	 *	Allocate the copy buffer
 	 */
-	struct sk_buff *n = __alloc_skb(newheadroom + skb->len + newtailroom,
-					gfp_mask, skb_alloc_rx_flag(skb),
-					NUMA_NO_NODE);
-	int oldheadroom = skb_headroom(skb);
 	int head_copy_len, head_copy_off;
+	struct sk_buff *n;
+	int oldheadroom;
 
+	if (WARN_ON_ONCE(skb_shinfo(skb)->gso_type & SKB_GSO_FRAGLIST))
+		return NULL;
+
+	oldheadroom = skb_headroom(skb);
+	n = __alloc_skb(newheadroom + skb->len + newtailroom,
+			gfp_mask, skb_alloc_rx_flag(skb),
+			NUMA_NO_NODE);
 	if (!n)
 		return NULL;
 
@@ -2028,6 +2072,30 @@
 EXPORT_SYMBOL(skb_pull);
 
 /**
+ *	skb_pull_data - remove data from the start of a buffer returning its
+ *	original position.
+ *	@skb: buffer to use
+ *	@len: amount of data to remove
+ *
+ *	This function removes data from the start of a buffer, returning
+ *	the memory to the headroom. A pointer to the original data in the buffer
+ *	is returned after checking if there is enough data to pull. Once the
+ *	data has been pulled future pushes will overwrite the old data.
+ */
+void *skb_pull_data(struct sk_buff *skb, size_t len)
+{
+	void *data = skb->data;
+
+	if (skb->len < len)
+		return NULL;
+
+	skb_pull(skb, len);
+
+	return data;
+}
+EXPORT_SYMBOL(skb_pull_data);
+
+/**
  *	skb_trim - remove end from a buffer
  *	@skb: buffer to alter
  *	@len: new length
@@ -2230,6 +2298,9 @@
 				insp = list;
 			} else {
 				/* Eaten partially. */
+				if (skb_is_gso(skb) && !list->head_frag &&
+				    skb_headlen(list))
+					skb_shinfo(skb)->gso_type |= SKB_GSO_DODGY;
 
 				if (skb_shared(list)) {
 					/* Sucks! We need to fork list. :-( */
@@ -2254,7 +2325,7 @@
 		/* Free pulled out fragments. */
 		while ((list = skb_shinfo(skb)->frag_list) != insp) {
 			skb_shinfo(skb)->frag_list = list->next;
-			kfree_skb(list);
+			consume_skb(list);
 		}
 		/* And insert new clone at head. */
 		if (clone) {
@@ -3449,19 +3520,7 @@
  */
 static int skb_prepare_for_shift(struct sk_buff *skb)
 {
-	int ret = 0;
-
-	if (skb_cloned(skb)) {
-		/* Save and restore truesize: pskb_expand_head() may reallocate
-		 * memory where ksize(kmalloc(S)) != ksize(kmalloc(S)), but we
-		 * cannot change truesize at this point.
-		 */
-		unsigned int save_truesize = skb->truesize;
-
-		ret = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
-		skb->truesize = save_truesize;
-	}
-	return ret;
+	return skb_unclone_keeptruesize(skb, GFP_ATOMIC);
 }
 
 /**
@@ -3800,7 +3859,7 @@
 		skb_frag_size_add(&skb_shinfo(skb)->frags[i - 1], size);
 	} else if (i < MAX_SKB_FRAGS) {
 		get_page(page);
-		skb_fill_page_desc(skb, i, page, offset, size);
+		skb_fill_page_desc_noacc(skb, i, page, offset, size);
 	} else {
 		return -EMSGSIZE;
 	}
@@ -3854,17 +3913,23 @@
 	unsigned int delta_len = 0;
 	struct sk_buff *tail = NULL;
 	struct sk_buff *nskb, *tmp;
-	int err;
+	int len_diff, err;
 
 	skb_push(skb, -skb_network_offset(skb) + offset);
 
+	/* Ensure the head is writeable before touching the shared info */
+	err = skb_unclone(skb, GFP_ATOMIC);
+	if (err)
+		goto err_linearize;
+
 	skb_shinfo(skb)->frag_list = NULL;
 
-	do {
+	while (list_skb) {
 		nskb = list_skb;
 		list_skb = list_skb->next;
 
 		err = 0;
+		delta_truesize += nskb->truesize;
 		if (skb_shared(nskb)) {
 			tmp = skb_clone(nskb, GFP_ATOMIC);
 			if (tmp) {
@@ -3889,14 +3954,15 @@
 		tail = nskb;
 
 		delta_len += nskb->len;
-		delta_truesize += nskb->truesize;
 
 		skb_push(nskb, -skb_network_offset(nskb) + offset);
 
 		skb_release_head_state(nskb);
+		len_diff = skb_network_header_len(nskb) - skb_network_header_len(skb);
 		__copy_skb_header(nskb, skb);
 
 		skb_headers_offset_update(nskb, skb_headroom(nskb) - skb_headroom(skb));
+		nskb->transport_header += len_diff;
 		skb_copy_from_linear_data_offset(skb, -tnl_hlen,
 						 nskb->data - tnl_hlen,
 						 offset + tnl_hlen);
@@ -3904,8 +3970,7 @@
 		if (skb_needs_linearize(nskb, features) &&
 		    __skb_linearize(nskb))
 			goto err_linearize;
-
-	} while (list_skb);
+	}
 
 	skb->truesize = skb->truesize - delta_truesize;
 	skb->data_len = skb->data_len - delta_len;
@@ -3946,8 +4011,9 @@
 	NAPI_GRO_CB(p)->count++;
 	p->data_len += skb->len;
 
-	/* sk owenrship - if any - completely transferred to the aggregated packet */
+	/* sk ownership - if any - completely transferred to the aggregated packet */
 	skb->destructor = NULL;
+	skb->sk = NULL;
 	p->truesize += skb->truesize;
 	p->len += skb->len;
 
@@ -3971,39 +4037,40 @@
 	struct sk_buff *segs = NULL;
 	struct sk_buff *tail = NULL;
 	struct sk_buff *list_skb = skb_shinfo(head_skb)->frag_list;
-	skb_frag_t *frag = skb_shinfo(head_skb)->frags;
 	unsigned int mss = skb_shinfo(head_skb)->gso_size;
 	unsigned int doffset = head_skb->data - skb_mac_header(head_skb);
-	struct sk_buff *frag_skb = head_skb;
 	unsigned int offset = doffset;
 	unsigned int tnl_hlen = skb_tnl_header_len(head_skb);
 	unsigned int partial_segs = 0;
 	unsigned int headroom;
 	unsigned int len = head_skb->len;
+	struct sk_buff *frag_skb;
+	skb_frag_t *frag;
 	__be16 proto;
 	bool csum, sg;
-	int nfrags = skb_shinfo(head_skb)->nr_frags;
 	int err = -ENOMEM;
 	int i = 0;
-	int pos;
+	int nfrags, pos;
 
-	if (list_skb && !list_skb->head_frag && skb_headlen(list_skb) &&
-	    (skb_shinfo(head_skb)->gso_type & SKB_GSO_DODGY)) {
-		/* gso_size is untrusted, and we have a frag_list with a linear
-		 * non head_frag head.
-		 *
-		 * (we assume checking the first list_skb member suffices;
-		 * i.e if either of the list_skb members have non head_frag
-		 * head, then the first one has too).
-		 *
-		 * If head_skb's headlen does not fit requested gso_size, it
-		 * means that the frag_list members do NOT terminate on exact
-		 * gso_size boundaries. Hence we cannot perform skb_frag_t page
-		 * sharing. Therefore we must fallback to copying the frag_list
-		 * skbs; we do so by disabling SG.
-		 */
-		if (mss != GSO_BY_FRAGS && mss != skb_headlen(head_skb))
-			features &= ~NETIF_F_SG;
+	if ((skb_shinfo(head_skb)->gso_type & SKB_GSO_DODGY) &&
+	    mss != GSO_BY_FRAGS && mss != skb_headlen(head_skb)) {
+		struct sk_buff *check_skb;
+
+		for (check_skb = list_skb; check_skb; check_skb = check_skb->next) {
+			if (skb_headlen(check_skb) && !check_skb->head_frag) {
+				/* gso_size is untrusted, and we have a frag_list with
+				 * a linear non head_frag item.
+				 *
+				 * If head_skb's headlen does not fit requested gso_size,
+				 * it means that the frag_list members do NOT terminate
+				 * on exact gso_size boundaries. Hence we cannot perform
+				 * skb_frag_t page sharing. Therefore we must fallback to
+				 * copying the frag_list skbs; we do so by disabling SG.
+				 */
+				features &= ~NETIF_F_SG;
+				break;
+			}
+		}
 	}
 
 	__skb_push(head_skb, doffset);
@@ -4048,8 +4115,9 @@
 		/* GSO partial only requires that we trim off any excess that
 		 * doesn't fit into an MSS sized block, so take care of that
 		 * now.
+		 * Cap len to not accidentally hit GSO_BY_FRAGS.
 		 */
-		partial_segs = len / mss;
+		partial_segs = min(len, GSO_BY_FRAGS - 1U) / mss;
 		if (partial_segs > 1)
 			mss *= partial_segs;
 		else
@@ -4060,6 +4128,13 @@
 	headroom = skb_headroom(head_skb);
 	pos = skb_headlen(head_skb);
 
+	if (skb_orphan_frags(head_skb, GFP_ATOMIC))
+		return ERR_PTR(-ENOMEM);
+
+	nfrags = skb_shinfo(head_skb)->nr_frags;
+	frag = skb_shinfo(head_skb)->frags;
+	frag_skb = head_skb;
+
 	do {
 		struct sk_buff *nskb;
 		skb_frag_t *nskb_frag;
@@ -4080,6 +4155,10 @@
 		    (skb_headlen(list_skb) == len || sg)) {
 			BUG_ON(skb_headlen(list_skb) > len);
 
+			nskb = skb_clone(list_skb, GFP_ATOMIC);
+			if (unlikely(!nskb))
+				goto err;
+
 			i = 0;
 			nfrags = skb_shinfo(list_skb)->nr_frags;
 			frag = skb_shinfo(list_skb)->frags;
@@ -4098,12 +4177,8 @@
 				frag++;
 			}
 
-			nskb = skb_clone(list_skb, GFP_ATOMIC);
 			list_skb = list_skb->next;
 
-			if (unlikely(!nskb))
-				goto err;
-
 			if (unlikely(pskb_trim(nskb, len))) {
 				kfree_skb(nskb);
 				goto err;
@@ -4165,9 +4240,8 @@
 				SKB_GSO_CB(nskb)->csum_start =
 					skb_headroom(nskb) + doffset;
 			} else {
-				skb_copy_bits(head_skb, offset,
-					      skb_put(nskb, len),
-					      len);
+				if (skb_copy_bits(head_skb, offset, skb_put(nskb, len), len))
+					goto err;
 			}
 			continue;
 		}
@@ -4180,12 +4254,16 @@
 		skb_shinfo(nskb)->flags |= skb_shinfo(head_skb)->flags &
 					   SKBFL_SHARED_FRAG;
 
-		if (skb_orphan_frags(frag_skb, GFP_ATOMIC) ||
-		    skb_zerocopy_clone(nskb, frag_skb, GFP_ATOMIC))
+		if (skb_zerocopy_clone(nskb, frag_skb, GFP_ATOMIC))
 			goto err;
 
 		while (pos < offset + len) {
 			if (i >= nfrags) {
+				if (skb_orphan_frags(list_skb, GFP_ATOMIC) ||
+				    skb_zerocopy_clone(nskb, list_skb,
+						       GFP_ATOMIC))
+					goto err;
+
 				i = 0;
 				nfrags = skb_shinfo(list_skb)->nr_frags;
 				frag = skb_shinfo(list_skb)->frags;
@@ -4199,10 +4277,6 @@
 					i--;
 					frag--;
 				}
-				if (skb_orphan_frags(frag_skb, GFP_ATOMIC) ||
-				    skb_zerocopy_clone(nskb, frag_skb,
-						       GFP_ATOMIC))
-					goto err;
 
 				list_skb = list_skb->next;
 			}
@@ -4387,8 +4461,9 @@
 	}
 
 merge:
-	/* sk owenrship - if any - completely transferred to the aggregated packet */
+	/* sk ownership - if any - completely transferred to the aggregated packet */
 	skb->destructor = NULL;
+	skb->sk = NULL;
 	delta_truesize = skb->truesize;
 	if (offset > headlen) {
 		unsigned int eat = offset - headlen;
@@ -4856,7 +4931,7 @@
 		serr->ee.ee_data = skb_shinfo(skb)->tskey;
 		if (sk->sk_protocol == IPPROTO_TCP &&
 		    sk->sk_type == SOCK_STREAM)
-			serr->ee.ee_data -= sk->sk_tskey;
+			serr->ee.ee_data -= atomic_read(&sk->sk_tskey);
 	}
 
 	err = sock_queue_err_skb(sk, skb);
@@ -4869,7 +4944,7 @@
 {
 	bool ret;
 
-	if (likely(sysctl_tstamp_allow_data || tsonly))
+	if (likely(READ_ONCE(sysctl_tstamp_allow_data) || tsonly))
 		return true;
 
 	read_lock_bh(&sk->sk_callback_lock);
@@ -4934,6 +5009,11 @@
 			skb = alloc_skb(0, GFP_ATOMIC);
 	} else {
 		skb = skb_clone(orig_skb, GFP_ATOMIC);
+
+		if (skb_orphan_frags_rx(skb, GFP_ATOMIC)) {
+			kfree_skb(skb);
+			return;
+		}
 	}
 	if (!skb)
 		return;
@@ -5371,11 +5451,18 @@
 	if (skb_cloned(to))
 		return false;
 
-	/* The page pool signature of struct page will eventually figure out
-	 * which pages can be recycled or not but for now let's prohibit slab
-	 * allocated and page_pool allocated SKBs from being coalesced.
+	/* In general, avoid mixing page_pool and non-page_pool allocated
+	 * pages within the same SKB. Additionally avoid dealing with clones
+	 * with page_pool pages, in case the SKB is using page_pool fragment
+	 * references (PP_FLAG_PAGE_FRAG). Since we only take full page
+	 * references for cloned SKBs at the moment that would result in
+	 * inconsistent reference counts.
+	 * In theory we could take full references if @from is cloned and
+	 * !@to->pp_recycle but its tricky (due to potential race with
+	 * the clone disappearing) and rare, so not worth dealing with.
 	 */
-	if (to->pp_recycle != from->pp_recycle)
+	if (to->pp_recycle != from->pp_recycle ||
+	    (from->pp_recycle && skb_cloned(from)))
 		return false;
 
 	if (len <= skb_tailroom(to)) {
@@ -5471,11 +5558,11 @@
 	skb->offload_fwd_mark = 0;
 	skb->offload_l3_fwd_mark = 0;
 #endif
+	ipvs_reset(skb);
 
 	if (!xnet)
 		return;
 
-	ipvs_reset(skb);
 	skb->mark = 0;
 	skb->tstamp = 0;
 }
@@ -6171,11 +6258,7 @@
 	skb->head = data;
 	skb->data = data;
 	skb->head_frag = 0;
-#ifdef NET_SKBUFF_DATA_USES_OFFSET
-	skb->end = size;
-#else
-	skb->end = skb->head + size;
-#endif
+	skb_set_end_offset(skb, size);
 	skb_set_tail_pointer(skb, skb_headlen(skb));
 	skb_headers_offset_update(skb, 0);
 	skb->cloned = 0;
@@ -6232,7 +6315,7 @@
 	/* Free pulled out fragments. */
 	while ((list = shinfo->frag_list) != insp) {
 		shinfo->frag_list = list->next;
-		kfree_skb(list);
+		consume_skb(list);
 	}
 	/* And insert new clone at head. */
 	if (clone) {
@@ -6313,11 +6396,7 @@
 	skb->head = data;
 	skb->head_frag = 0;
 	skb->data = data;
-#ifdef NET_SKBUFF_DATA_USES_OFFSET
-	skb->end = size;
-#else
-	skb->end = skb->head + size;
-#endif
+	skb_set_end_offset(skb, size);
 	skb_reset_tail_pointer(skb);
 	skb_headers_offset_update(skb, 0);
 	skb->cloned   = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/skmsg.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/skmsg.c
@@ -27,6 +27,7 @@
 		 int elem_first_coalesce)
 {
 	struct page_frag *pfrag = sk_page_frag(sk);
+	u32 osize = msg->sg.size;
 	int ret = 0;
 
 	len -= msg->sg.size;
@@ -35,13 +36,17 @@
 		u32 orig_offset;
 		int use, i;
 
-		if (!sk_page_frag_refill(sk, pfrag))
-			return -ENOMEM;
+		if (!sk_page_frag_refill(sk, pfrag)) {
+			ret = -ENOMEM;
+			goto msg_trim;
+		}
 
 		orig_offset = pfrag->offset;
 		use = min_t(int, len, pfrag->size - orig_offset);
-		if (!sk_wmem_schedule(sk, use))
-			return -ENOMEM;
+		if (!sk_wmem_schedule(sk, use)) {
+			ret = -ENOMEM;
+			goto msg_trim;
+		}
 
 		i = msg->sg.end;
 		sk_msg_iter_var_prev(i);
@@ -71,6 +76,10 @@
 	}
 
 	return ret;
+
+msg_trim:
+	sk_msg_trim(sk, msg, osize);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(sk_msg_alloc);
 
@@ -425,16 +434,21 @@
 			page = sg_page(sge);
 			if (copied + copy > len)
 				copy = len - copied;
-			copy = copy_page_to_iter(page, sge->offset, copy, iter);
-			if (!copy)
-				return copied ? copied : -EFAULT;
+			if (copy)
+				copy = copy_page_to_iter(page, sge->offset, copy, iter);
+			if (!copy) {
+				copied = copied ? copied : -EFAULT;
+				goto out;
+			}
 
 			copied += copy;
 			if (likely(!peek)) {
 				sge->offset += copy;
 				sge->length -= copy;
-				if (!msg_rx->skb)
+				if (!msg_rx->skb) {
 					sk_mem_uncharge(sk, copy);
+					atomic_sub(copy, &sk->sk_rmem_alloc);
+				}
 				msg_rx->sg.size -= copy;
 
 				if (!sge->length) {
@@ -447,13 +461,13 @@
 				 * didn't copy the entire length lets just break.
 				 */
 				if (copy != sge->length)
-					return copied;
+					goto out;
 				sk_msg_iter_var_next(i);
 			}
 
 			if (copied == len)
 				break;
-		} while (i != msg_rx->sg.end);
+		} while ((i != msg_rx->sg.end) && !sg_is_last(sge));
 
 		if (unlikely(peek)) {
 			msg_rx = sk_psock_next_msg(psock, msg_rx);
@@ -463,13 +477,13 @@
 		}
 
 		msg_rx->sg.start = i;
-		if (!sge->length && msg_rx->sg.start == msg_rx->sg.end) {
+		if (!sge->length && (i == msg_rx->sg.end || sg_is_last(sge))) {
 			msg_rx = sk_psock_dequeue_msg(psock);
 			kfree_sk_msg(msg_rx);
 		}
 		msg_rx = sk_psock_peek_msg(psock);
 	}
-
+out:
 	return copied;
 }
 EXPORT_SYMBOL_GPL(sk_msg_recvmsg);
@@ -508,6 +522,7 @@
 }
 
 static int sk_psock_skb_ingress_enqueue(struct sk_buff *skb,
+					u32 off, u32 len,
 					struct sk_psock *psock,
 					struct sock *sk,
 					struct sk_msg *msg)
@@ -521,11 +536,11 @@
 	 */
 	if (skb_linearize(skb))
 		return -EAGAIN;
-	num_sge = skb_to_sgvec(skb, msg->sg.data, 0, skb->len);
+	num_sge = skb_to_sgvec(skb, msg->sg.data, off, len);
 	if (unlikely(num_sge < 0))
 		return num_sge;
 
-	copied = skb->len;
+	copied = len;
 	msg->sg.start = 0;
 	msg->sg.size = copied;
 	msg->sg.end = num_sge;
@@ -536,9 +551,11 @@
 	return copied;
 }
 
-static int sk_psock_skb_ingress_self(struct sk_psock *psock, struct sk_buff *skb);
+static int sk_psock_skb_ingress_self(struct sk_psock *psock, struct sk_buff *skb,
+				     u32 off, u32 len);
 
-static int sk_psock_skb_ingress(struct sk_psock *psock, struct sk_buff *skb)
+static int sk_psock_skb_ingress(struct sk_psock *psock, struct sk_buff *skb,
+				u32 off, u32 len)
 {
 	struct sock *sk = psock->sk;
 	struct sk_msg *msg;
@@ -549,7 +566,7 @@
 	 * correctly.
 	 */
 	if (unlikely(skb->sk == sk))
-		return sk_psock_skb_ingress_self(psock, skb);
+		return sk_psock_skb_ingress_self(psock, skb, off, len);
 	msg = sk_psock_create_ingress_msg(sk, skb);
 	if (!msg)
 		return -EAGAIN;
@@ -561,7 +578,7 @@
 	 * into user buffers.
 	 */
 	skb_set_owner_r(skb, sk);
-	err = sk_psock_skb_ingress_enqueue(skb, psock, sk, msg);
+	err = sk_psock_skb_ingress_enqueue(skb, off, len, psock, sk, msg);
 	if (err < 0)
 		kfree(msg);
 	return err;
@@ -571,7 +588,8 @@
  * skb. In this case we do not need to check memory limits or skb_set_owner_r
  * because the skb is already accounted for here.
  */
-static int sk_psock_skb_ingress_self(struct sk_psock *psock, struct sk_buff *skb)
+static int sk_psock_skb_ingress_self(struct sk_psock *psock, struct sk_buff *skb,
+				     u32 off, u32 len)
 {
 	struct sk_msg *msg = kzalloc(sizeof(*msg), __GFP_NOWARN | GFP_ATOMIC);
 	struct sock *sk = psock->sk;
@@ -581,7 +599,7 @@
 		return -EAGAIN;
 	sk_msg_init(msg);
 	skb_set_owner_r(skb, sk);
-	err = sk_psock_skb_ingress_enqueue(skb, psock, sk, msg);
+	err = sk_psock_skb_ingress_enqueue(skb, off, len, psock, sk, msg);
 	if (err < 0)
 		kfree(msg);
 	return err;
@@ -595,50 +613,46 @@
 			return -EAGAIN;
 		return skb_send_sock(psock->sk, skb, off, len);
 	}
-	return sk_psock_skb_ingress(psock, skb);
+	return sk_psock_skb_ingress(psock, skb, off, len);
 }
 
 static void sk_psock_skb_state(struct sk_psock *psock,
 			       struct sk_psock_work_state *state,
-			       struct sk_buff *skb,
 			       int len, int off)
 {
 	spin_lock_bh(&psock->ingress_lock);
 	if (sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED)) {
-		state->skb = skb;
 		state->len = len;
 		state->off = off;
-	} else {
-		sock_drop(psock->sk, skb);
 	}
 	spin_unlock_bh(&psock->ingress_lock);
 }
 
 static void sk_psock_backlog(struct work_struct *work)
 {
-	struct sk_psock *psock = container_of(work, struct sk_psock, work);
+	struct delayed_work *dwork = to_delayed_work(work);
+	struct sk_psock *psock = container_of(dwork, struct sk_psock, work);
 	struct sk_psock_work_state *state = &psock->work_state;
 	struct sk_buff *skb = NULL;
+	u32 len = 0, off = 0;
 	bool ingress;
-	u32 len, off;
 	int ret;
 
 	mutex_lock(&psock->work_mutex);
-	if (unlikely(state->skb)) {
-		spin_lock_bh(&psock->ingress_lock);
-		skb = state->skb;
+	if (unlikely(state->len)) {
 		len = state->len;
 		off = state->off;
-		state->skb = NULL;
-		spin_unlock_bh(&psock->ingress_lock);
 	}
-	if (skb)
-		goto start;
 
-	while ((skb = skb_dequeue(&psock->ingress_skb))) {
+	while ((skb = skb_peek(&psock->ingress_skb))) {
 		len = skb->len;
 		off = 0;
-start:
+		if (skb_bpf_strparser(skb)) {
+			struct strp_msg *stm = strp_msg(skb);
+
+			off = stm->offset;
+			len = stm->full_len;
+		}
 		ingress = skb_bpf_ingress(skb);
 		skb_bpf_redirect_clear(skb);
 		do {
@@ -648,22 +662,28 @@
 							  len, ingress);
 			if (ret <= 0) {
 				if (ret == -EAGAIN) {
-					sk_psock_skb_state(psock, state, skb,
-							   len, off);
+					sk_psock_skb_state(psock, state, len, off);
+
+					/* Delay slightly to prioritize any
+					 * other work that might be here.
+					 */
+					if (sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED))
+						schedule_delayed_work(&psock->work, 1);
 					goto end;
 				}
 				/* Hard errors break pipe and stop xmit. */
 				sk_psock_report_error(psock, ret ? -ret : EPIPE);
 				sk_psock_clear_state(psock, SK_PSOCK_TX_ENABLED);
-				sock_drop(psock->sk, skb);
 				goto end;
 			}
 			off += ret;
 			len -= ret;
 		} while (len);
 
-		if (!ingress)
+		skb = skb_dequeue(&psock->ingress_skb);
+		if (!ingress) {
 			kfree_skb(skb);
+		}
 	}
 end:
 	mutex_unlock(&psock->work_mutex);
@@ -676,6 +696,11 @@
 
 	write_lock_bh(&sk->sk_callback_lock);
 
+	if (sk_is_inet(sk) && inet_csk_has_ulp(sk)) {
+		psock = ERR_PTR(-EINVAL);
+		goto out;
+	}
+
 	if (sk->sk_user_data) {
 		psock = ERR_PTR(-EBUSY);
 		goto out;
@@ -692,13 +717,14 @@
 	psock->eval = __SK_NONE;
 	psock->sk_proto = prot;
 	psock->saved_unhash = prot->unhash;
+	psock->saved_destroy = prot->destroy;
 	psock->saved_close = prot->close;
 	psock->saved_write_space = sk->sk_write_space;
 
 	INIT_LIST_HEAD(&psock->link);
 	spin_lock_init(&psock->link_lock);
 
-	INIT_WORK(&psock->work, sk_psock_backlog);
+	INIT_DELAYED_WORK(&psock->work, sk_psock_backlog);
 	mutex_init(&psock->work_mutex);
 	INIT_LIST_HEAD(&psock->ingress_msg);
 	spin_lock_init(&psock->ingress_lock);
@@ -707,7 +733,9 @@
 	sk_psock_set_state(psock, SK_PSOCK_TX_ENABLED);
 	refcount_set(&psock->refcnt, 1);
 
-	rcu_assign_sk_user_data_nocopy(sk, psock);
+	__rcu_assign_sk_user_data_with_flags(sk, psock,
+					     SK_USER_DATA_NOCOPY |
+					     SK_USER_DATA_PSOCK);
 	sock_hold(sk);
 
 out:
@@ -735,6 +763,8 @@
 
 	list_for_each_entry_safe(msg, tmp, &psock->ingress_msg, list) {
 		list_del(&msg->list);
+		if (!msg->skb)
+			atomic_sub(msg->sg.size, &psock->sk->sk_rmem_alloc);
 		sk_msg_free(psock->sk, msg);
 		kfree(msg);
 	}
@@ -748,11 +778,6 @@
 		skb_bpf_redirect_clear(skb);
 		sock_drop(psock->sk, skb);
 	}
-	kfree_skb(psock->work_state.skb);
-	/* We null the skb here to ensure that calls to sk_psock_backlog
-	 * do not pick up the free'd skb.
-	 */
-	psock->work_state.skb = NULL;
 	__sk_psock_purge_ingress_msg(psock);
 }
 
@@ -766,16 +791,12 @@
 	}
 }
 
-void sk_psock_stop(struct sk_psock *psock, bool wait)
+void sk_psock_stop(struct sk_psock *psock)
 {
 	spin_lock_bh(&psock->ingress_lock);
 	sk_psock_clear_state(psock, SK_PSOCK_TX_ENABLED);
 	sk_psock_cork_free(psock);
-	__sk_psock_zap_ingress(psock);
 	spin_unlock_bh(&psock->ingress_lock);
-
-	if (wait)
-		cancel_work_sync(&psock->work);
 }
 
 static void sk_psock_done_strp(struct sk_psock *psock);
@@ -788,7 +809,8 @@
 
 	sk_psock_done_strp(psock);
 
-	cancel_work_sync(&psock->work);
+	cancel_delayed_work_sync(&psock->work);
+	__sk_psock_zap_ingress(psock);
 	mutex_destroy(&psock->work_mutex);
 
 	psock_progs_drop(&psock->progs);
@@ -813,7 +835,7 @@
 		sk_psock_stop_verdict(sk, psock);
 	write_unlock_bh(&sk->sk_callback_lock);
 
-	sk_psock_stop(psock, false);
+	sk_psock_stop(psock);
 
 	INIT_RCU_WORK(&psock->rwork, sk_psock_destroy);
 	queue_rcu_work(system_wq, &psock->rwork);
@@ -852,13 +874,16 @@
 	ret = sk_psock_map_verd(ret, msg->sk_redir);
 	psock->apply_bytes = msg->apply_bytes;
 	if (ret == __SK_REDIRECT) {
-		if (psock->sk_redir)
+		if (psock->sk_redir) {
 			sock_put(psock->sk_redir);
-		psock->sk_redir = msg->sk_redir;
-		if (!psock->sk_redir) {
+			psock->sk_redir = NULL;
+		}
+		if (!msg->sk_redir) {
 			ret = __SK_DROP;
 			goto out;
 		}
+		psock->redir_ingress = sk_msg_to_ingress(msg);
+		psock->sk_redir = msg->sk_redir;
 		sock_hold(psock->sk_redir);
 	}
 out:
@@ -877,6 +902,7 @@
 	 * return code, but then didn't set a redirect interface.
 	 */
 	if (unlikely(!sk_other)) {
+		skb_bpf_redirect_clear(skb);
 		sock_drop(from->sk, skb);
 		return -EIO;
 	}
@@ -899,7 +925,7 @@
 	}
 
 	skb_queue_tail(&psock_other->ingress_skb, skb);
-	schedule_work(&psock_other->work);
+	schedule_delayed_work(&psock_other->work, 0);
 	spin_unlock_bh(&psock_other->ingress_lock);
 	return 0;
 }
@@ -944,6 +970,7 @@
 {
 	struct sock *sk_other;
 	int err = 0;
+	u32 len, off;
 
 	switch (verdict) {
 	case __SK_PASS:
@@ -951,6 +978,7 @@
 		sk_other = psock->sk;
 		if (sock_flag(sk_other, SOCK_DEAD) ||
 		    !sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED)) {
+			skb_bpf_redirect_clear(skb);
 			goto out_free;
 		}
 
@@ -963,13 +991,21 @@
 		 * retrying later from workqueue.
 		 */
 		if (skb_queue_empty(&psock->ingress_skb)) {
-			err = sk_psock_skb_ingress_self(psock, skb);
+			len = skb->len;
+			off = 0;
+			if (skb_bpf_strparser(skb)) {
+				struct strp_msg *stm = strp_msg(skb);
+
+				off = stm->offset;
+				len = stm->full_len;
+			}
+			err = sk_psock_skb_ingress_self(psock, skb, off, len);
 		}
 		if (err < 0) {
 			spin_lock_bh(&psock->ingress_lock);
 			if (sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED)) {
 				skb_queue_tail(&psock->ingress_skb, skb);
-				schedule_work(&psock->work);
+				schedule_delayed_work(&psock->work, 0);
 				err = 0;
 			}
 			spin_unlock_bh(&psock->ingress_lock);
@@ -1000,7 +1036,7 @@
 	psock = sk_psock(sk);
 	if (likely(psock)) {
 		if (sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED))
-			schedule_work(&psock->work);
+			schedule_delayed_work(&psock->work, 0);
 		write_space = psock->saved_write_space;
 	}
 	rcu_read_unlock();
@@ -1029,6 +1065,8 @@
 		skb_dst_drop(skb);
 		skb_bpf_redirect_clear(skb);
 		ret = bpf_prog_run_pin_on_cpu(prog, skb);
+		if (ret == SK_PASS)
+			skb_bpf_set_strparser(skb);
 		ret = sk_psock_map_verd(ret, skb_bpf_redirect_fetch(skb));
 		skb->sk = NULL;
 	}
@@ -1070,9 +1108,9 @@
 		if (tls_sw_has_ctx_rx(sk)) {
 			psock->saved_data_ready(sk);
 		} else {
-			write_lock_bh(&sk->sk_callback_lock);
+			read_lock_bh(&sk->sk_callback_lock);
 			strp_data_ready(&psock->strp);
-			write_unlock_bh(&sk->sk_callback_lock);
+			read_unlock_bh(&sk->sk_callback_lock);
 		}
 	}
 	rcu_read_unlock();
@@ -1080,13 +1118,19 @@
 
 int sk_psock_init_strp(struct sock *sk, struct sk_psock *psock)
 {
+	int ret;
+
 	static const struct strp_callbacks cb = {
 		.rcv_msg	= sk_psock_strp_read,
 		.read_sock_done	= sk_psock_strp_read_done,
 		.parse_msg	= sk_psock_strp_parse,
 	};
 
-	return strp_init(&psock->strp, sk, &cb);
+	ret = strp_init(&psock->strp, sk, &cb);
+	if (!ret)
+		sk_psock_set_state(psock, SK_PSOCK_RX_STRP_ENABLED);
+
+	return ret;
 }
 
 void sk_psock_start_strp(struct sock *sk, struct sk_psock *psock)
@@ -1101,6 +1145,8 @@
 
 void sk_psock_stop_strp(struct sock *sk, struct sk_psock *psock)
 {
+	psock_set_prog(&psock->progs.stream_parser, NULL);
+
 	if (!psock->saved_data_ready)
 		return;
 
@@ -1112,7 +1158,7 @@
 static void sk_psock_done_strp(struct sk_psock *psock)
 {
 	/* Parser has been stopped */
-	if (psock->progs.stream_parser)
+	if (sk_psock_test_state(psock, SK_PSOCK_RX_STRP_ENABLED))
 		strp_done(&psock->strp);
 }
 #else
@@ -1128,7 +1174,7 @@
 	struct sk_psock *psock;
 	struct bpf_prog *prog;
 	int ret = __SK_DROP;
-	int len = skb->len;
+	int len = orig_len;
 
 	/* clone here so sk_eat_skb() in tcp_read_sock does not drop our data */
 	skb = skb_clone(skb, GFP_ATOMIC);
@@ -1189,6 +1235,9 @@
 
 void sk_psock_stop_verdict(struct sock *sk, struct sk_psock *psock)
 {
+	psock_set_prog(&psock->progs.stream_verdict, NULL);
+	psock_set_prog(&psock->progs.skb_verdict, NULL);
+
 	if (!psock->saved_data_ready)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/sock.c
@@ -144,8 +144,6 @@
 static DEFINE_MUTEX(proto_list_mutex);
 static LIST_HEAD(proto_list);
 
-static void sock_inuse_add(struct net *net, int val);
-
 /**
  * sk_ns_capable - General socket capability test
  * @sk: Socket to use a capability on or through
@@ -459,7 +457,7 @@
 	unsigned long flags;
 	struct sk_buff_head *list = &sk->sk_receive_queue;
 
-	if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf) {
+	if (atomic_read(&sk->sk_rmem_alloc) >= READ_ONCE(sk->sk_rcvbuf)) {
 		atomic_inc(&sk->sk_drops);
 		trace_sock_rcvqueue_full(sk, skb);
 		return -ENOMEM;
@@ -511,7 +509,7 @@
 
 	skb->dev = NULL;
 
-	if (sk_rcvqueues_full(sk, sk->sk_rcvbuf)) {
+	if (sk_rcvqueues_full(sk, READ_ONCE(sk->sk_rcvbuf))) {
 		atomic_inc(&sk->sk_drops);
 		goto discard_and_relse;
 	}
@@ -557,7 +555,7 @@
 	    INDIRECT_CALL_INET(dst->ops->check, ip6_dst_check, ipv4_dst_check,
 			       dst, cookie) == NULL) {
 		sk_tx_queue_clear(sk);
-		sk->sk_dst_pending_confirm = 0;
+		WRITE_ONCE(sk->sk_dst_pending_confirm, 0);
 		RCU_INIT_POINTER(sk->sk_dst_cache, NULL);
 		dst_release(dst);
 		return NULL;
@@ -671,8 +669,8 @@
 	return ret;
 }
 
-static int sock_getbindtodevice(struct sock *sk, char __user *optval,
-				int __user *optlen, int len)
+static int sock_getbindtodevice(struct sock *sk, sockptr_t optval,
+				sockptr_t optlen, int len)
 {
 	int ret = -ENOPROTOOPT;
 #ifdef CONFIG_NETDEVICES
@@ -695,12 +693,12 @@
 	len = strlen(devname) + 1;
 
 	ret = -EFAULT;
-	if (copy_to_user(optval, devname, len))
+	if (copy_to_sockptr(optval, devname, len))
 		goto out;
 
 zero:
 	ret = -EFAULT;
-	if (put_user(len, optlen))
+	if (copy_to_sockptr(optlen, &len, sizeof(int)))
 		goto out;
 
 	ret = 0;
@@ -717,7 +715,8 @@
 		return false;
 	if (!sk)
 		return true;
-	switch (sk->sk_family) {
+	/* IPV6_ADDRFORM can change sk->sk_family under us. */
+	switch (READ_ONCE(sk->sk_family)) {
 	case AF_INET:
 		return inet_sk(sk)->mc_loop;
 #if IS_ENABLED(CONFIG_IPV6)
@@ -830,6 +829,8 @@
 	}
 
 	num = ethtool_get_phc_vclocks(dev, &vclock_index);
+	dev_put(dev);
+
 	for (i = 0; i < num; i++) {
 		if (*(vclock_index + i) == phc_index) {
 			match = true;
@@ -864,9 +865,9 @@
 			if ((1 << sk->sk_state) &
 			    (TCPF_CLOSE | TCPF_LISTEN))
 				return -EINVAL;
-			sk->sk_tskey = tcp_sk(sk)->snd_una;
+			atomic_set(&sk->sk_tskey, tcp_sk(sk)->snd_una);
 		} else {
-			sk->sk_tskey = 0;
+			atomic_set(&sk->sk_tskey, 0);
 		}
 	}
 
@@ -991,7 +992,10 @@
 		sk->sk_reuse = (valbool ? SK_CAN_REUSE : SK_NO_REUSE);
 		break;
 	case SO_REUSEPORT:
-		sk->sk_reuseport = valbool;
+		if (valbool && !sk_is_inet(sk))
+			ret = -EOPNOTSUPP;
+		else
+			sk->sk_reuseport = valbool;
 		break;
 	case SO_TYPE:
 	case SO_PROTOCOL:
@@ -1012,7 +1016,7 @@
 		 * play 'guess the biggest size' games. RCVBUF/SNDBUF
 		 * are treated in BSD as hints
 		 */
-		val = min_t(u32, val, sysctl_wmem_max);
+		val = min_t(u32, val, READ_ONCE(sysctl_wmem_max));
 set_sndbuf:
 		/* Ensure val * 2 fits into an int, to prevent max_t()
 		 * from treating it as a negative value.
@@ -1044,7 +1048,7 @@
 		 * play 'guess the biggest size' games. RCVBUF/SNDBUF
 		 * are treated in BSD as hints
 		 */
-		__sock_set_rcvbuf(sk, min_t(u32, val, sysctl_rmem_max));
+		__sock_set_rcvbuf(sk, min_t(u32, val, READ_ONCE(sysctl_rmem_max)));
 		break;
 
 	case SO_RCVBUFFORCE:
@@ -1295,12 +1299,13 @@
 			cmpxchg(&sk->sk_pacing_status,
 				SK_PACING_NONE,
 				SK_PACING_NEEDED);
-		sk->sk_max_pacing_rate = ulval;
+		/* Pairs with READ_ONCE() from sk_getsockopt() */
+		WRITE_ONCE(sk->sk_max_pacing_rate, ulval);
 		sk->sk_pacing_rate = min(sk->sk_pacing_rate, ulval);
 		break;
 		}
 	case SO_INCOMING_CPU:
-		WRITE_ONCE(sk->sk_incoming_cpu, val);
+		reuseport_update_incoming_cpu(sk, val);
 		break;
 
 	case SO_CNX_ADVICE:
@@ -1400,22 +1405,25 @@
 	}
 }
 
-static int groups_to_user(gid_t __user *dst, const struct group_info *src)
+static int groups_to_user(sockptr_t dst, const struct group_info *src)
 {
 	struct user_namespace *user_ns = current_user_ns();
 	int i;
 
-	for (i = 0; i < src->ngroups; i++)
-		if (put_user(from_kgid_munged(user_ns, src->gid[i]), dst + i))
+	for (i = 0; i < src->ngroups; i++) {
+		gid_t gid = from_kgid_munged(user_ns, src->gid[i]);
+
+		if (copy_to_sockptr_offset(dst, i * sizeof(gid), &gid, sizeof(gid)))
 			return -EFAULT;
+	}
 
 	return 0;
 }
 
-int sock_getsockopt(struct socket *sock, int level, int optname,
-		    char __user *optval, int __user *optlen)
+static int sk_getsockopt(struct sock *sk, int level, int optname,
+			 sockptr_t optval, sockptr_t optlen)
 {
-	struct sock *sk = sock->sk;
+	struct socket *sock = sk->sk_socket;
 
 	union {
 		int val;
@@ -1432,7 +1440,7 @@
 	int lv = sizeof(int);
 	int len;
 
-	if (get_user(len, optlen))
+	if (copy_from_sockptr(&len, optlen, sizeof(int)))
 		return -EFAULT;
 	if (len < 0)
 		return -EINVAL;
@@ -1453,11 +1461,11 @@
 		break;
 
 	case SO_SNDBUF:
-		v.val = sk->sk_sndbuf;
+		v.val = READ_ONCE(sk->sk_sndbuf);
 		break;
 
 	case SO_RCVBUF:
-		v.val = sk->sk_rcvbuf;
+		v.val = READ_ONCE(sk->sk_rcvbuf);
 		break;
 
 	case SO_REUSEADDR:
@@ -1530,9 +1538,16 @@
 		break;
 
 	case SO_TIMESTAMPING_OLD:
+	case SO_TIMESTAMPING_NEW:
 		lv = sizeof(v.timestamping);
-		v.timestamping.flags = sk->sk_tsflags;
-		v.timestamping.bind_phc = sk->sk_bind_phc;
+		/* For the later-added case SO_TIMESTAMPING_NEW: Be strict about only
+		 * returning the flags when they were set through the same option.
+		 * Don't change the beviour for the old case SO_TIMESTAMPING_OLD.
+		 */
+		if (optname == SO_TIMESTAMPING_OLD || sock_flag(sk, SOCK_TSTAMP_NEW)) {
+			v.timestamping.flags = sk->sk_tsflags;
+			v.timestamping.bind_phc = sk->sk_bind_phc;
+		}
 		break;
 
 	case SO_RCVTIMEO_OLD:
@@ -1546,7 +1561,7 @@
 		break;
 
 	case SO_RCVLOWAT:
-		v.val = sk->sk_rcvlowat;
+		v.val = READ_ONCE(sk->sk_rcvlowat);
 		break;
 
 	case SO_SNDLOWAT:
@@ -1567,7 +1582,7 @@
 		cred_to_ucred(sk->sk_peer_pid, sk->sk_peer_cred, &peercred);
 		spin_unlock(&sk->sk_peer_lock);
 
-		if (copy_to_user(optval, &peercred, len))
+		if (copy_to_sockptr(optval, &peercred, len))
 			return -EFAULT;
 		goto lenout;
 	}
@@ -1585,11 +1600,11 @@
 		if (len < n * sizeof(gid_t)) {
 			len = n * sizeof(gid_t);
 			put_cred(cred);
-			return put_user(len, optlen) ? -EFAULT : -ERANGE;
+			return copy_to_sockptr(optlen, &len, sizeof(int)) ? -EFAULT : -ERANGE;
 		}
 		len = n * sizeof(gid_t);
 
-		ret = groups_to_user((gid_t __user *)optval, cred->group_info);
+		ret = groups_to_user(optval, cred->group_info);
 		put_cred(cred);
 		if (ret)
 			return ret;
@@ -1605,7 +1620,7 @@
 			return -ENOTCONN;
 		if (lv < len)
 			return -EINVAL;
-		if (copy_to_user(optval, address, len))
+		if (copy_to_sockptr(optval, address, len))
 			return -EFAULT;
 		goto lenout;
 	}
@@ -1622,7 +1637,7 @@
 		break;
 
 	case SO_PEERSEC:
-		return security_socket_getpeersec_stream(sock, optval, optlen, len);
+		return security_socket_getpeersec_stream(sock, optval.user, optlen.user, len);
 
 	case SO_MARK:
 		v.val = sk->sk_mark;
@@ -1640,7 +1655,7 @@
 		if (!sock->ops->set_peek_off)
 			return -EOPNOTSUPP;
 
-		v.val = sk->sk_peek_off;
+		v.val = READ_ONCE(sk->sk_peek_off);
 		break;
 	case SO_NOFCS:
 		v.val = sock_flag(sk, SOCK_NOFCS);
@@ -1650,7 +1665,7 @@
 		return sock_getbindtodevice(sk, optval, optlen, len);
 
 	case SO_GET_FILTER:
-		len = sk_get_filter(sk, (struct sock_filter __user *)optval, len);
+		len = sk_get_filter(sk, optval, len);
 		if (len < 0)
 			return len;
 
@@ -1670,7 +1685,7 @@
 
 #ifdef CONFIG_NET_RX_BUSY_POLL
 	case SO_BUSY_POLL:
-		v.val = sk->sk_ll_usec;
+		v.val = READ_ONCE(sk->sk_ll_usec);
 		break;
 	case SO_PREFER_BUSY_POLL:
 		v.val = READ_ONCE(sk->sk_prefer_busy_poll);
@@ -1678,12 +1693,14 @@
 #endif
 
 	case SO_MAX_PACING_RATE:
+		/* The READ_ONCE() pair with the WRITE_ONCE() in sk_setsockopt() */
 		if (sizeof(v.ulval) != sizeof(v.val) && len >= sizeof(v.ulval)) {
 			lv = sizeof(v.ulval);
-			v.ulval = sk->sk_max_pacing_rate;
+			v.ulval = READ_ONCE(sk->sk_max_pacing_rate);
 		} else {
 			/* 32bit version */
-			v.val = min_t(unsigned long, sk->sk_max_pacing_rate, ~0U);
+			v.val = min_t(unsigned long, ~0U,
+				      READ_ONCE(sk->sk_max_pacing_rate));
 		}
 		break;
 
@@ -1698,7 +1715,7 @@
 		sk_get_meminfo(sk, meminfo);
 
 		len = min_t(unsigned int, len, sizeof(meminfo));
-		if (copy_to_user(optval, &meminfo, len))
+		if (copy_to_sockptr(optval, &meminfo, len))
 			return -EFAULT;
 
 		goto lenout;
@@ -1759,14 +1776,22 @@
 
 	if (len > lv)
 		len = lv;
-	if (copy_to_user(optval, &v, len))
+	if (copy_to_sockptr(optval, &v, len))
 		return -EFAULT;
 lenout:
-	if (put_user(len, optlen))
+	if (copy_to_sockptr(optlen, &len, sizeof(int)))
 		return -EFAULT;
 	return 0;
 }
 
+int sock_getsockopt(struct socket *sock, int level, int optname,
+		    char __user *optval, int __user *optlen)
+{
+	return sk_getsockopt(sock->sk, level, optname,
+			     USER_SOCKPTR(optval),
+			     USER_SOCKPTR(optlen));
+}
+
 /*
  * Initialize an sk_lock.
  *
@@ -2043,8 +2068,10 @@
 	newsk->sk_prot_creator = prot;
 
 	/* SANITY */
-	if (likely(newsk->sk_net_refcnt))
+	if (likely(newsk->sk_net_refcnt)) {
 		get_net(sock_net(newsk));
+		sock_inuse_add(sock_net(newsk), 1);
+	}
 	sk_node_init(&newsk->sk_node);
 	sock_lock_init(newsk);
 	bh_lock_sock(newsk);
@@ -2115,8 +2142,6 @@
 	newsk->sk_err_soft = 0;
 	newsk->sk_priority = 0;
 	newsk->sk_incoming_cpu = raw_smp_processor_id();
-	if (likely(newsk->sk_net_refcnt))
-		sock_inuse_add(sock_net(newsk), 1);
 
 	/* Before updating sk_refcnt, we must commit prior changes to memory
 	 * (Documentation/RCU/rculist_nulls.rst for details)
@@ -2163,7 +2188,6 @@
 {
 	u32 max_segs = 1;
 
-	sk_dst_set(sk, dst);
 	sk->sk_route_caps = dst->dev->features | sk->sk_route_forced_caps;
 	if (sk->sk_route_caps & NETIF_F_GSO)
 		sk->sk_route_caps |= NETIF_F_GSO_SOFTWARE;
@@ -2178,6 +2202,7 @@
 		}
 	}
 	sk->sk_gso_max_segs = max_segs;
+	sk_dst_set(sk, dst);
 }
 EXPORT_SYMBOL_GPL(sk_setup_caps);
 
@@ -2322,13 +2347,24 @@
 }
 EXPORT_SYMBOL(sock_i_uid);
 
-unsigned long sock_i_ino(struct sock *sk)
+unsigned long __sock_i_ino(struct sock *sk)
 {
 	unsigned long ino;
 
-	read_lock_bh(&sk->sk_callback_lock);
+	read_lock(&sk->sk_callback_lock);
 	ino = sk->sk_socket ? SOCK_INODE(sk->sk_socket)->i_ino : 0;
-	read_unlock_bh(&sk->sk_callback_lock);
+	read_unlock(&sk->sk_callback_lock);
+	return ino;
+}
+EXPORT_SYMBOL(__sock_i_ino);
+
+unsigned long sock_i_ino(struct sock *sk)
+{
+	unsigned long ino;
+
+	local_bh_disable();
+	ino = __sock_i_ino(sk);
+	local_bh_enable();
 	return ino;
 }
 EXPORT_SYMBOL(sock_i_ino);
@@ -2366,7 +2402,7 @@
 
 	/* small safe race: SKB_TRUESIZE may differ from final skb->truesize */
 	if (atomic_read(&sk->sk_omem_alloc) + SKB_TRUESIZE(size) >
-	    sysctl_optmem_max)
+	    READ_ONCE(sysctl_optmem_max))
 		return NULL;
 
 	skb = alloc_skb(size, priority);
@@ -2384,8 +2420,10 @@
  */
 void *sock_kmalloc(struct sock *sk, int size, gfp_t priority)
 {
-	if ((unsigned int)size <= sysctl_optmem_max &&
-	    atomic_read(&sk->sk_omem_alloc) + size < sysctl_optmem_max) {
+	int optmem_max = READ_ONCE(sysctl_optmem_max);
+
+	if ((unsigned int)size <= optmem_max &&
+	    atomic_read(&sk->sk_omem_alloc) + size < optmem_max) {
 		void *mem;
 		/* First do the add, to avoid the race if kmalloc
 		 * might sleep.
@@ -2445,9 +2483,9 @@
 		prepare_to_wait(sk_sleep(sk), &wait, TASK_INTERRUPTIBLE);
 		if (refcount_read(&sk->sk_wmem_alloc) < READ_ONCE(sk->sk_sndbuf))
 			break;
-		if (sk->sk_shutdown & SEND_SHUTDOWN)
+		if (READ_ONCE(sk->sk_shutdown) & SEND_SHUTDOWN)
 			break;
-		if (sk->sk_err)
+		if (READ_ONCE(sk->sk_err))
 			break;
 		timeo = schedule_timeout(timeo);
 	}
@@ -2475,7 +2513,7 @@
 			goto failure;
 
 		err = -EPIPE;
-		if (sk->sk_shutdown & SEND_SHUTDOWN)
+		if (READ_ONCE(sk->sk_shutdown) & SEND_SHUTDOWN)
 			goto failure;
 
 		if (sk_wmem_alloc_get(sk) < READ_ONCE(sk->sk_sndbuf))
@@ -2525,6 +2563,7 @@
 		sockc->mark = *(u32 *)CMSG_DATA(cmsg);
 		break;
 	case SO_TIMESTAMPING_OLD:
+	case SO_TIMESTAMPING_NEW:
 		if (cmsg->cmsg_len != CMSG_LEN(sizeof(u32)))
 			return -EINVAL;
 
@@ -2862,7 +2901,7 @@
 	if (mem_cgroup_sockets_enabled && sk->sk_memcg)
 		mem_cgroup_uncharge_skmem(sk->sk_memcg, amount);
 
-	if (sk_under_memory_pressure(sk) &&
+	if (sk_under_global_memory_pressure(sk) &&
 	    (sk_memory_allocated(sk) < sk_prot_mem_limits(sk, 0)))
 		sk_leave_memory_pressure(sk);
 }
@@ -2883,7 +2922,7 @@
 
 int sk_set_peek_off(struct sock *sk, int val)
 {
-	sk->sk_peek_off = val;
+	WRITE_ONCE(sk->sk_peek_off, val);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(sk_set_peek_off);
@@ -3114,7 +3153,7 @@
 }
 EXPORT_SYMBOL(sk_stop_timer_sync);
 
-void sock_init_data(struct socket *sock, struct sock *sk)
+void sock_init_data_uid(struct socket *sock, struct sock *sk, kuid_t uid)
 {
 	sk_init_common(sk);
 	sk->sk_send_head	=	NULL;
@@ -3122,8 +3161,8 @@
 	timer_setup(&sk->sk_timer, NULL, 0);
 
 	sk->sk_allocation	=	GFP_KERNEL;
-	sk->sk_rcvbuf		=	sysctl_rmem_default;
-	sk->sk_sndbuf		=	sysctl_wmem_default;
+	sk->sk_rcvbuf		=	READ_ONCE(sysctl_rmem_default);
+	sk->sk_sndbuf		=	READ_ONCE(sysctl_wmem_default);
 	sk->sk_state		=	TCP_CLOSE;
 	sk_set_socket(sk, sock);
 
@@ -3133,11 +3172,10 @@
 		sk->sk_type	=	sock->type;
 		RCU_INIT_POINTER(sk->sk_wq, &sock->wq);
 		sock->sk	=	sk;
-		sk->sk_uid	=	SOCK_INODE(sock)->i_uid;
 	} else {
 		RCU_INIT_POINTER(sk->sk_wq, NULL);
-		sk->sk_uid	=	make_kuid(sock_net(sk)->user_ns, 0);
 	}
+	sk->sk_uid	=	uid;
 
 	rwlock_init(&sk->sk_callback_lock);
 	if (sk->sk_kern_sock)
@@ -3178,7 +3216,7 @@
 
 #ifdef CONFIG_NET_RX_BUSY_POLL
 	sk->sk_napi_id		=	0;
-	sk->sk_ll_usec		=	sysctl_net_busy_read;
+	sk->sk_ll_usec		=	READ_ONCE(sysctl_net_busy_read);
 #endif
 
 	sk->sk_max_pacing_rate = ~0UL;
@@ -3195,6 +3233,16 @@
 	refcount_set(&sk->sk_refcnt, 1);
 	atomic_set(&sk->sk_drops, 0);
 }
+EXPORT_SYMBOL(sock_init_data_uid);
+
+void sock_init_data(struct socket *sock, struct sock *sk)
+{
+	kuid_t uid = sock ?
+		SOCK_INODE(sock)->i_uid :
+		make_kuid(sock_net(sk)->user_ns, 0);
+
+	sock_init_data_uid(sock, sk, uid);
+}
 EXPORT_SYMBOL(sock_init_data);
 
 void lock_sock_nested(struct sock *sk, int subclass)
@@ -3366,7 +3414,8 @@
 {
 	struct sock *sk = sock->sk;
 
-	return sk->sk_prot->getsockopt(sk, level, optname, optval, optlen);
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	return READ_ONCE(sk->sk_prot)->getsockopt(sk, level, optname, optval, optlen);
 }
 EXPORT_SYMBOL(sock_common_getsockopt);
 
@@ -3393,7 +3442,8 @@
 {
 	struct sock *sk = sock->sk;
 
-	return sk->sk_prot->setsockopt(sk, level, optname, optval, optlen);
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	return READ_ONCE(sk->sk_prot)->setsockopt(sk, level, optname, optval, optlen);
 }
 EXPORT_SYMBOL(sock_common_setsockopt);
 
@@ -3412,6 +3462,9 @@
 
 	sk->sk_prot->unhash(sk);
 
+	if (sk->sk_socket)
+		sk->sk_socket->sk = NULL;
+
 	/*
 	 * In this point socket cannot receive new packets, but it is possible
 	 * that some packets are in flight because some CPU runs receiver and
@@ -3450,19 +3503,8 @@
 }
 
 #ifdef CONFIG_PROC_FS
-#define PROTO_INUSE_NR	64	/* should be enough for the first time */
-struct prot_inuse {
-	int val[PROTO_INUSE_NR];
-};
-
 static DECLARE_BITMAP(proto_inuse_idx, PROTO_INUSE_NR);
 
-void sock_prot_inuse_add(struct net *net, struct proto *prot, int val)
-{
-	__this_cpu_add(net->core.prot_inuse->val[prot->inuse_idx], val);
-}
-EXPORT_SYMBOL_GPL(sock_prot_inuse_add);
-
 int sock_prot_inuse_get(struct net *net, struct proto *prot)
 {
 	int cpu, idx = prot->inuse_idx;
@@ -3475,11 +3517,6 @@
 }
 EXPORT_SYMBOL_GPL(sock_prot_inuse_get);
 
-static void sock_inuse_add(struct net *net, int val)
-{
-	this_cpu_add(*net->core.sock_inuse, val);
-}
-
 int sock_inuse_get(struct net *net)
 {
 	int cpu, res = 0;
@@ -3558,9 +3595,6 @@
 {
 }
 
-static void sock_inuse_add(struct net *net, int val)
-{
-}
 #endif
 
 static void tw_prot_cleanup(struct timewait_sock_ops *twsk_prot)
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/sock_diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/sock_diag.c
@@ -189,7 +189,7 @@
 	if (sock_diag_handlers[hndl->family])
 		err = -EBUSY;
 	else
-		sock_diag_handlers[hndl->family] = hndl;
+		WRITE_ONCE(sock_diag_handlers[hndl->family], hndl);
 	mutex_unlock(&sock_diag_table_mutex);
 
 	return err;
@@ -205,7 +205,7 @@
 
 	mutex_lock(&sock_diag_table_mutex);
 	BUG_ON(sock_diag_handlers[family] != hnld);
-	sock_diag_handlers[family] = NULL;
+	WRITE_ONCE(sock_diag_handlers[family], NULL);
 	mutex_unlock(&sock_diag_table_mutex);
 }
 EXPORT_SYMBOL_GPL(sock_diag_unregister);
@@ -223,7 +223,7 @@
 		return -EINVAL;
 	req->sdiag_family = array_index_nospec(req->sdiag_family, AF_MAX);
 
-	if (sock_diag_handlers[req->sdiag_family] == NULL)
+	if (READ_ONCE(sock_diag_handlers[req->sdiag_family]) == NULL)
 		sock_load_diag_module(req->sdiag_family, 0);
 
 	mutex_lock(&sock_diag_table_mutex);
@@ -282,12 +282,12 @@
 	switch (group) {
 	case SKNLGRP_INET_TCP_DESTROY:
 	case SKNLGRP_INET_UDP_DESTROY:
-		if (!sock_diag_handlers[AF_INET])
+		if (!READ_ONCE(sock_diag_handlers[AF_INET]))
 			sock_load_diag_module(AF_INET, 0);
 		break;
 	case SKNLGRP_INET6_TCP_DESTROY:
 	case SKNLGRP_INET6_UDP_DESTROY:
-		if (!sock_diag_handlers[AF_INET6])
+		if (!READ_ONCE(sock_diag_handlers[AF_INET6]))
 			sock_load_diag_module(AF_INET6, 0);
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/sock_map.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/sock_map.c
@@ -117,7 +117,6 @@
 	__acquires(&sk->sk_lock.slock)
 {
 	lock_sock(sk);
-	preempt_disable();
 	rcu_read_lock();
 }
 
@@ -125,7 +124,6 @@
 	__releases(&sk->sk_lock.slock)
 {
 	rcu_read_unlock();
-	preempt_enable();
 	release_sock(sk);
 }
 
@@ -150,16 +148,17 @@
 	list_for_each_entry_safe(link, tmp, &psock->link, list) {
 		if (link->link_raw == link_raw) {
 			struct bpf_map *map = link->map;
-			struct bpf_stab *stab = container_of(map, struct bpf_stab,
-							     map);
-			if (psock->saved_data_ready && stab->progs.stream_parser)
+			struct sk_psock_progs *progs = sock_map_progs(map);
+
+			if (psock->saved_data_ready && progs->stream_parser)
 				strp_stop = true;
-			if (psock->saved_data_ready && stab->progs.stream_verdict)
+			if (psock->saved_data_ready && progs->stream_verdict)
 				verdict_stop = true;
-			if (psock->saved_data_ready && stab->progs.skb_verdict)
+			if (psock->saved_data_ready && progs->skb_verdict)
 				verdict_stop = true;
 			list_del(&link->list);
 			sk_psock_free_link(link);
+			break;
 		}
 	}
 	spin_unlock_bh(&psock->link_lock);
@@ -167,8 +166,11 @@
 		write_lock_bh(&sk->sk_callback_lock);
 		if (strp_stop)
 			sk_psock_stop_strp(sk, psock);
-		else
+		if (verdict_stop)
 			sk_psock_stop_verdict(sk, psock);
+
+		if (psock->psock_update_sk_prot)
+			psock->psock_update_sk_prot(sk, psock, false);
 		write_unlock_bh(&sk->sk_callback_lock);
 	}
 }
@@ -282,32 +284,38 @@
 
 	if (msg_parser)
 		psock_set_prog(&psock->progs.msg_parser, msg_parser);
+	if (stream_parser)
+		psock_set_prog(&psock->progs.stream_parser, stream_parser);
+	if (stream_verdict)
+		psock_set_prog(&psock->progs.stream_verdict, stream_verdict);
+	if (skb_verdict)
+		psock_set_prog(&psock->progs.skb_verdict, skb_verdict);
 
+	/* msg_* and stream_* programs references tracked in psock after this
+	 * point. Reference dec and cleanup will occur through psock destructor
+	 */
 	ret = sock_map_init_proto(sk, psock);
-	if (ret < 0)
-		goto out_drop;
+	if (ret < 0) {
+		sk_psock_put(sk, psock);
+		goto out;
+	}
 
 	write_lock_bh(&sk->sk_callback_lock);
 	if (stream_parser && stream_verdict && !psock->saved_data_ready) {
 		ret = sk_psock_init_strp(sk, psock);
-		if (ret)
-			goto out_unlock_drop;
-		psock_set_prog(&psock->progs.stream_verdict, stream_verdict);
-		psock_set_prog(&psock->progs.stream_parser, stream_parser);
+		if (ret) {
+			write_unlock_bh(&sk->sk_callback_lock);
+			sk_psock_put(sk, psock);
+			goto out;
+		}
 		sk_psock_start_strp(sk, psock);
 	} else if (!stream_parser && stream_verdict && !psock->saved_data_ready) {
-		psock_set_prog(&psock->progs.stream_verdict, stream_verdict);
 		sk_psock_start_verdict(sk,psock);
 	} else if (!stream_verdict && skb_verdict && !psock->saved_data_ready) {
-		psock_set_prog(&psock->progs.skb_verdict, skb_verdict);
 		sk_psock_start_verdict(sk, psock);
 	}
 	write_unlock_bh(&sk->sk_callback_lock);
 	return 0;
-out_unlock_drop:
-	write_unlock_bh(&sk->sk_callback_lock);
-out_drop:
-	sk_psock_put(sk, psock);
 out_progs:
 	if (skb_verdict)
 		bpf_prog_put(skb_verdict);
@@ -320,6 +328,7 @@
 out_put_stream_verdict:
 	if (stream_verdict)
 		bpf_prog_put(stream_verdict);
+out:
 	return ret;
 }
 
@@ -339,11 +348,13 @@
 
 		sk = xchg(psk, NULL);
 		if (sk) {
+			sock_hold(sk);
 			lock_sock(sk);
 			rcu_read_lock();
 			sock_map_unref(sk, psk);
 			rcu_read_unlock();
 			release_sock(sk);
+			sock_put(sk);
 		}
 	}
 
@@ -400,12 +411,14 @@
 static int __sock_map_delete(struct bpf_stab *stab, struct sock *sk_test,
 			     struct sock **psk)
 {
-	struct sock *sk;
+	struct sock *sk = NULL;
 	int err = 0;
 
+	if (irqs_disabled())
+		return -EOPNOTSUPP; /* locks here are hardirq-unsafe */
+
 	raw_spin_lock_bh(&stab->lock);
-	sk = *psk;
-	if (!sk_test || sk_test == sk)
+	if (!sk_test || sk_test == *psk)
 		sk = xchg(psk, NULL);
 
 	if (likely(sk))
@@ -666,6 +679,8 @@
 	sk = __sock_map_lookup_elem(map, key);
 	if (unlikely(!sk || !sock_map_redirect_allowed(sk)))
 		return SK_DROP;
+	if (!(flags & BPF_F_INGRESS) && !sk_is_tcp(sk))
+		return SK_DROP;
 
 	msg->flags = flags;
 	msg->sk_redir = sk;
@@ -779,13 +794,22 @@
 {
 	struct sock_map_seq_info *info = priv_data;
 
+	bpf_map_inc_with_uref(aux->map);
 	info->map = aux->map;
 	return 0;
 }
 
+static void sock_map_fini_seq_private(void *priv_data)
+{
+	struct sock_map_seq_info *info = priv_data;
+
+	bpf_map_put_with_uref(info->map);
+}
+
 static const struct bpf_iter_seq_info sock_map_iter_seq_info = {
 	.seq_ops		= &sock_map_seq_ops,
 	.init_seq_private	= sock_map_init_seq_private,
+	.fini_seq_private	= sock_map_fini_seq_private,
 	.seq_priv_size		= sizeof(struct sock_map_seq_info),
 };
 
@@ -910,6 +934,9 @@
 	struct bpf_shtab_elem *elem;
 	int ret = -ENOENT;
 
+	if (irqs_disabled())
+		return -EOPNOTSUPP; /* locks here are hardirq-unsafe */
+
 	hash = sock_hash_bucket_hash(key, key_size);
 	bucket = sock_hash_select_bucket(htab, hash);
 
@@ -1150,6 +1177,7 @@
 			sock_put(elem->sk);
 			sock_hash_free_elem(htab, elem);
 		}
+		cond_resched();
 	}
 
 	/* wait for psock readers accessing its map link */
@@ -1250,6 +1278,8 @@
 	sk = __sock_hash_lookup_elem(map, key);
 	if (unlikely(!sk || !sock_map_redirect_allowed(sk)))
 		return SK_DROP;
+	if (!(flags & BPF_F_INGRESS) && !sk_is_tcp(sk))
+		return SK_DROP;
 
 	msg->flags = flags;
 	msg->sk_redir = sk;
@@ -1366,18 +1396,27 @@
 };
 
 static int sock_hash_init_seq_private(void *priv_data,
-				     struct bpf_iter_aux_info *aux)
+				      struct bpf_iter_aux_info *aux)
 {
 	struct sock_hash_seq_info *info = priv_data;
 
+	bpf_map_inc_with_uref(aux->map);
 	info->map = aux->map;
 	info->htab = container_of(aux->map, struct bpf_shtab, map);
 	return 0;
 }
 
+static void sock_hash_fini_seq_private(void *priv_data)
+{
+	struct sock_hash_seq_info *info = priv_data;
+
+	bpf_map_put_with_uref(info->map);
+}
+
 static const struct bpf_iter_seq_info sock_hash_iter_seq_info = {
 	.seq_ops		= &sock_hash_seq_ops,
 	.init_seq_private	= sock_hash_init_seq_private,
+	.fini_seq_private	= sock_hash_fini_seq_private,
 	.seq_priv_size		= sizeof(struct sock_hash_seq_info),
 };
 
@@ -1484,18 +1523,43 @@
 	psock = sk_psock(sk);
 	if (unlikely(!psock)) {
 		rcu_read_unlock();
-		if (sk->sk_prot->unhash)
-			sk->sk_prot->unhash(sk);
-		return;
+		saved_unhash = READ_ONCE(sk->sk_prot)->unhash;
+	} else {
+		saved_unhash = psock->saved_unhash;
+		sock_map_remove_links(sk, psock);
+		rcu_read_unlock();
 	}
-
-	saved_unhash = psock->saved_unhash;
-	sock_map_remove_links(sk, psock);
-	rcu_read_unlock();
-	saved_unhash(sk);
+	if (WARN_ON_ONCE(saved_unhash == sock_map_unhash))
+		return;
+	if (saved_unhash)
+		saved_unhash(sk);
 }
 EXPORT_SYMBOL_GPL(sock_map_unhash);
 
+void sock_map_destroy(struct sock *sk)
+{
+	void (*saved_destroy)(struct sock *sk);
+	struct sk_psock *psock;
+
+	rcu_read_lock();
+	psock = sk_psock_get(sk);
+	if (unlikely(!psock)) {
+		rcu_read_unlock();
+		saved_destroy = READ_ONCE(sk->sk_prot)->destroy;
+	} else {
+		saved_destroy = psock->saved_destroy;
+		sock_map_remove_links(sk, psock);
+		rcu_read_unlock();
+		sk_psock_stop(psock);
+		sk_psock_put(sk, psock);
+	}
+	if (WARN_ON_ONCE(saved_destroy == sock_map_destroy))
+		return;
+	if (saved_destroy)
+		saved_destroy(sk);
+}
+EXPORT_SYMBOL_GPL(sock_map_destroy);
+
 void sock_map_close(struct sock *sk, long timeout)
 {
 	void (*saved_close)(struct sock *sk, long timeout);
@@ -1503,19 +1567,30 @@
 
 	lock_sock(sk);
 	rcu_read_lock();
-	psock = sk_psock_get(sk);
-	if (unlikely(!psock)) {
+	psock = sk_psock(sk);
+	if (likely(psock)) {
+		saved_close = psock->saved_close;
+		sock_map_remove_links(sk, psock);
+		psock = sk_psock_get(sk);
+		if (unlikely(!psock))
+			goto no_psock;
+		rcu_read_unlock();
+		sk_psock_stop(psock);
+		release_sock(sk);
+		cancel_delayed_work_sync(&psock->work);
+		sk_psock_put(sk, psock);
+	} else {
+		saved_close = READ_ONCE(sk->sk_prot)->close;
+no_psock:
 		rcu_read_unlock();
 		release_sock(sk);
-		return sk->sk_prot->close(sk, timeout);
 	}
 
-	saved_close = psock->saved_close;
-	sock_map_remove_links(sk, psock);
-	rcu_read_unlock();
-	sk_psock_stop(psock, true);
-	sk_psock_put(sk, psock);
-	release_sock(sk);
+	/* Make sure we do not recurse. This is a bug.
+	 * Leak the socket instead of crashing on a stack overflow.
+	 */
+	if (WARN_ON_ONCE(saved_close == sock_map_close))
+		return;
 	saved_close(sk, timeout);
 }
 EXPORT_SYMBOL_GPL(sock_map_close);
@@ -1565,7 +1640,7 @@
 	.ctx_arg_info_size	= 2,
 	.ctx_arg_info		= {
 		{ offsetof(struct bpf_iter__sockmap, key),
-		  PTR_TO_RDONLY_BUF_OR_NULL },
+		  PTR_TO_BUF | PTR_MAYBE_NULL | MEM_RDONLY },
 		{ offsetof(struct bpf_iter__sockmap, sk),
 		  PTR_TO_BTF_ID_OR_NULL },
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/sock_reuseport.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/sock_reuseport.c
@@ -21,6 +21,86 @@
 static int reuseport_resurrect(struct sock *sk, struct sock_reuseport *old_reuse,
 			       struct sock_reuseport *reuse, bool bind_inany);
 
+void reuseport_has_conns_set(struct sock *sk)
+{
+	struct sock_reuseport *reuse;
+
+	if (!rcu_access_pointer(sk->sk_reuseport_cb))
+		return;
+
+	spin_lock_bh(&reuseport_lock);
+	reuse = rcu_dereference_protected(sk->sk_reuseport_cb,
+					  lockdep_is_held(&reuseport_lock));
+	if (likely(reuse))
+		reuse->has_conns = 1;
+	spin_unlock_bh(&reuseport_lock);
+}
+EXPORT_SYMBOL(reuseport_has_conns_set);
+
+static void __reuseport_get_incoming_cpu(struct sock_reuseport *reuse)
+{
+	/* Paired with READ_ONCE() in reuseport_select_sock_by_hash(). */
+	WRITE_ONCE(reuse->incoming_cpu, reuse->incoming_cpu + 1);
+}
+
+static void __reuseport_put_incoming_cpu(struct sock_reuseport *reuse)
+{
+	/* Paired with READ_ONCE() in reuseport_select_sock_by_hash(). */
+	WRITE_ONCE(reuse->incoming_cpu, reuse->incoming_cpu - 1);
+}
+
+static void reuseport_get_incoming_cpu(struct sock *sk, struct sock_reuseport *reuse)
+{
+	if (sk->sk_incoming_cpu >= 0)
+		__reuseport_get_incoming_cpu(reuse);
+}
+
+static void reuseport_put_incoming_cpu(struct sock *sk, struct sock_reuseport *reuse)
+{
+	if (sk->sk_incoming_cpu >= 0)
+		__reuseport_put_incoming_cpu(reuse);
+}
+
+void reuseport_update_incoming_cpu(struct sock *sk, int val)
+{
+	struct sock_reuseport *reuse;
+	int old_sk_incoming_cpu;
+
+	if (unlikely(!rcu_access_pointer(sk->sk_reuseport_cb))) {
+		/* Paired with REAE_ONCE() in sk_incoming_cpu_update()
+		 * and compute_score().
+		 */
+		WRITE_ONCE(sk->sk_incoming_cpu, val);
+		return;
+	}
+
+	spin_lock_bh(&reuseport_lock);
+
+	/* This must be done under reuseport_lock to avoid a race with
+	 * reuseport_grow(), which accesses sk->sk_incoming_cpu without
+	 * lock_sock() when detaching a shutdown()ed sk.
+	 *
+	 * Paired with READ_ONCE() in reuseport_select_sock_by_hash().
+	 */
+	old_sk_incoming_cpu = sk->sk_incoming_cpu;
+	WRITE_ONCE(sk->sk_incoming_cpu, val);
+
+	reuse = rcu_dereference_protected(sk->sk_reuseport_cb,
+					  lockdep_is_held(&reuseport_lock));
+
+	/* reuseport_grow() has detached a closed sk. */
+	if (!reuse)
+		goto out;
+
+	if (old_sk_incoming_cpu < 0 && val >= 0)
+		__reuseport_get_incoming_cpu(reuse);
+	else if (old_sk_incoming_cpu >= 0 && val < 0)
+		__reuseport_put_incoming_cpu(reuse);
+
+out:
+	spin_unlock_bh(&reuseport_lock);
+}
+
 static int reuseport_sock_index(struct sock *sk,
 				const struct sock_reuseport *reuse,
 				bool closed)
@@ -48,6 +128,7 @@
 	/* paired with smp_rmb() in reuseport_(select|migrate)_sock() */
 	smp_wmb();
 	reuse->num_socks++;
+	reuseport_get_incoming_cpu(sk, reuse);
 }
 
 static bool __reuseport_detach_sock(struct sock *sk,
@@ -60,6 +141,7 @@
 
 	reuse->socks[i] = reuse->socks[reuse->num_socks - 1];
 	reuse->num_socks--;
+	reuseport_put_incoming_cpu(sk, reuse);
 
 	return true;
 }
@@ -70,6 +152,7 @@
 	reuse->socks[reuse->max_socks - reuse->num_closed_socks - 1] = sk;
 	/* paired with READ_ONCE() in inet_csk_bind_conflict() */
 	WRITE_ONCE(reuse->num_closed_socks, reuse->num_closed_socks + 1);
+	reuseport_get_incoming_cpu(sk, reuse);
 }
 
 static bool __reuseport_detach_closed_sock(struct sock *sk,
@@ -83,6 +166,7 @@
 	reuse->socks[i] = reuse->socks[reuse->max_socks - reuse->num_closed_socks];
 	/* paired with READ_ONCE() in inet_csk_bind_conflict() */
 	WRITE_ONCE(reuse->num_closed_socks, reuse->num_closed_socks - 1);
+	reuseport_put_incoming_cpu(sk, reuse);
 
 	return true;
 }
@@ -150,6 +234,7 @@
 	reuse->bind_inany = bind_inany;
 	reuse->socks[0] = sk;
 	reuse->num_socks = 1;
+	reuseport_get_incoming_cpu(sk, reuse);
 	rcu_assign_pointer(sk->sk_reuseport_cb, reuse);
 
 out:
@@ -193,6 +278,7 @@
 	more_reuse->reuseport_id = reuse->reuseport_id;
 	more_reuse->bind_inany = reuse->bind_inany;
 	more_reuse->has_conns = reuse->has_conns;
+	more_reuse->incoming_cpu = reuse->incoming_cpu;
 
 	memcpy(more_reuse->socks, reuse->socks,
 	       reuse->num_socks * sizeof(struct sock *));
@@ -387,7 +473,7 @@
 		prog = rcu_dereference_protected(reuse->prog,
 						 lockdep_is_held(&reuseport_lock));
 
-		if (sock_net(sk)->ipv4.sysctl_tcp_migrate_req ||
+		if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_migrate_req) ||
 		    (prog && prog->expected_attach_type == BPF_SK_REUSEPORT_SELECT_OR_MIGRATE)) {
 			/* Migration capable, move sk from the listening section
 			 * to the closed section.
@@ -442,18 +528,32 @@
 static struct sock *reuseport_select_sock_by_hash(struct sock_reuseport *reuse,
 						  u32 hash, u16 num_socks)
 {
+	struct sock *first_valid_sk = NULL;
 	int i, j;
 
 	i = j = reciprocal_scale(hash, num_socks);
-	while (reuse->socks[i]->sk_state == TCP_ESTABLISHED) {
+	do {
+		struct sock *sk = reuse->socks[i];
+
+		if (sk->sk_state != TCP_ESTABLISHED) {
+			/* Paired with WRITE_ONCE() in __reuseport_(get|put)_incoming_cpu(). */
+			if (!READ_ONCE(reuse->incoming_cpu))
+				return sk;
+
+			/* Paired with WRITE_ONCE() in reuseport_update_incoming_cpu(). */
+			if (READ_ONCE(sk->sk_incoming_cpu) == raw_smp_processor_id())
+				return sk;
+
+			if (!first_valid_sk)
+				first_valid_sk = sk;
+		}
+
 		i++;
 		if (i >= num_socks)
 			i = 0;
-		if (i == j)
-			return NULL;
-	}
+	} while (i != j);
 
-	return reuse->socks[i];
+	return first_valid_sk;
 }
 
 /**
@@ -545,7 +645,7 @@
 	hash = migrating_sk->sk_hash;
 	prog = rcu_dereference(reuse->prog);
 	if (!prog || prog->expected_attach_type != BPF_SK_REUSEPORT_SELECT_OR_MIGRATE) {
-		if (sock_net(sk)->ipv4.sysctl_tcp_migrate_req)
+		if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_migrate_req))
 			goto select_by_hash;
 		goto failure;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/stream.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/stream.c
@@ -73,8 +73,8 @@
 		add_wait_queue(sk_sleep(sk), &wait);
 		sk->sk_write_pending++;
 		done = sk_wait_event(sk, timeo_p,
-				     !sk->sk_err &&
-				     !((1 << sk->sk_state) &
+				     !READ_ONCE(sk->sk_err) &&
+				     !((1 << READ_ONCE(sk->sk_state)) &
 				       ~(TCPF_ESTABLISHED | TCPF_CLOSE_WAIT)), &wait);
 		remove_wait_queue(sk_sleep(sk), &wait);
 		sk->sk_write_pending--;
@@ -87,9 +87,9 @@
  * sk_stream_closing - Return 1 if we still have things to send in our buffers.
  * @sk: socket to verify
  */
-static inline int sk_stream_closing(struct sock *sk)
+static int sk_stream_closing(const struct sock *sk)
 {
-	return (1 << sk->sk_state) &
+	return (1 << READ_ONCE(sk->sk_state)) &
 	       (TCPF_FIN_WAIT1 | TCPF_CLOSING | TCPF_LAST_ACK);
 }
 
@@ -142,8 +142,8 @@
 
 		set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
 		sk->sk_write_pending++;
-		sk_wait_event(sk, &current_timeo, sk->sk_err ||
-						  (sk->sk_shutdown & SEND_SHUTDOWN) ||
+		sk_wait_event(sk, &current_timeo, READ_ONCE(sk->sk_err) ||
+						  (READ_ONCE(sk->sk_shutdown) & SEND_SHUTDOWN) ||
 						  (sk_stream_memory_free(sk) &&
 						  !vm_wait), &wait);
 		sk->sk_write_pending--;
@@ -159,7 +159,8 @@
 		*timeo_p = current_timeo;
 	}
 out:
-	remove_wait_queue(sk_sleep(sk), &wait);
+	if (!sock_flag(sk, SOCK_DEAD))
+		remove_wait_queue(sk_sleep(sk), &wait);
 	return err;
 
 do_error:
@@ -195,8 +196,11 @@
 	/* First the read buffer. */
 	__skb_queue_purge(&sk->sk_receive_queue);
 
-	/* Next, the error queue. */
-	__skb_queue_purge(&sk->sk_error_queue);
+	/* Next, the error queue.
+	 * We need to use queue lock, because other threads might
+	 * add packets to the queue without socket lock being held.
+	 */
+	skb_queue_purge(&sk->sk_error_queue);
 
 	/* Next, the write queue. */
 	WARN_ON(!skb_queue_empty(&sk->sk_write_queue));
@@ -205,7 +209,6 @@
 	sk_mem_reclaim(sk);
 
 	WARN_ON(sk->sk_wmem_queued);
-	WARN_ON(sk->sk_forward_alloc);
 
 	/* It is _impossible_ for the backlog to contain anything
 	 * when we get here.  All user references to this socket
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/sysctl_net_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/sysctl_net_core.c
@@ -236,14 +236,17 @@
 static int proc_do_dev_weight(struct ctl_table *table, int write,
 			   void *buffer, size_t *lenp, loff_t *ppos)
 {
-	int ret;
+	static DEFINE_MUTEX(dev_weight_mutex);
+	int ret, weight;
 
-	ret = proc_dointvec(table, write, buffer, lenp, ppos);
-	if (ret != 0)
-		return ret;
-
-	dev_rx_weight = weight_p * dev_weight_rx_bias;
-	dev_tx_weight = weight_p * dev_weight_tx_bias;
+	mutex_lock(&dev_weight_mutex);
+	ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
+	if (!ret && write) {
+		weight = READ_ONCE(weight_p);
+		WRITE_ONCE(dev_rx_weight, weight * dev_weight_rx_bias);
+		WRITE_ONCE(dev_tx_weight, weight * dev_weight_tx_bias);
+	}
+	mutex_unlock(&dev_weight_mutex);
 
 	return ret;
 }
@@ -348,6 +351,7 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_do_dev_weight,
+		.extra1         = SYSCTL_ONE,
 	},
 	{
 		.procname	= "dev_weight_rx_bias",
@@ -355,6 +359,7 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_do_dev_weight,
+		.extra1         = SYSCTL_ONE,
 	},
 	{
 		.procname	= "dev_weight_tx_bias",
@@ -362,6 +367,7 @@
 		.maxlen		= sizeof(int),
 		.mode		= 0644,
 		.proc_handler	= proc_do_dev_weight,
+		.extra1         = SYSCTL_ONE,
 	},
 	{
 		.procname	= "netdev_max_backlog",
--- linux-xilinx-zynqmp-5.15.0.orig/net/core/xdp.c
+++ linux-xilinx-zynqmp-5.15.0/net/core/xdp.c
@@ -110,31 +110,35 @@
 	mutex_unlock(&mem_id_lock);
 }
 
-void xdp_rxq_info_unreg_mem_model(struct xdp_rxq_info *xdp_rxq)
+void xdp_unreg_mem_model(struct xdp_mem_info *mem)
 {
 	struct xdp_mem_allocator *xa;
-	int type = xdp_rxq->mem.type;
-	int id = xdp_rxq->mem.id;
+	int type = mem->type;
+	int id = mem->id;
 
 	/* Reset mem info to defaults */
-	xdp_rxq->mem.id = 0;
-	xdp_rxq->mem.type = 0;
-
-	if (xdp_rxq->reg_state != REG_STATE_REGISTERED) {
-		WARN(1, "Missing register, driver bug");
-		return;
-	}
+	mem->id = 0;
+	mem->type = 0;
 
 	if (id == 0)
 		return;
 
 	if (type == MEM_TYPE_PAGE_POOL) {
-		rcu_read_lock();
-		xa = rhashtable_lookup(mem_id_ht, &id, mem_id_rht_params);
+		xa = rhashtable_lookup_fast(mem_id_ht, &id, mem_id_rht_params);
 		page_pool_destroy(xa->page_pool);
-		rcu_read_unlock();
 	}
 }
+EXPORT_SYMBOL_GPL(xdp_unreg_mem_model);
+
+void xdp_rxq_info_unreg_mem_model(struct xdp_rxq_info *xdp_rxq)
+{
+	if (xdp_rxq->reg_state != REG_STATE_REGISTERED) {
+		WARN(1, "Missing register, driver bug");
+		return;
+	}
+
+	xdp_unreg_mem_model(&xdp_rxq->mem);
+}
 EXPORT_SYMBOL_GPL(xdp_rxq_info_unreg_mem_model);
 
 void xdp_rxq_info_unreg(struct xdp_rxq_info *xdp_rxq)
@@ -261,28 +265,24 @@
 	return true;
 }
 
-int xdp_rxq_info_reg_mem_model(struct xdp_rxq_info *xdp_rxq,
-			       enum xdp_mem_type type, void *allocator)
+static struct xdp_mem_allocator *__xdp_reg_mem_model(struct xdp_mem_info *mem,
+						     enum xdp_mem_type type,
+						     void *allocator)
 {
 	struct xdp_mem_allocator *xdp_alloc;
 	gfp_t gfp = GFP_KERNEL;
 	int id, errno, ret;
 	void *ptr;
 
-	if (xdp_rxq->reg_state != REG_STATE_REGISTERED) {
-		WARN(1, "Missing register, driver bug");
-		return -EFAULT;
-	}
-
 	if (!__is_supported_mem_type(type))
-		return -EOPNOTSUPP;
+		return ERR_PTR(-EOPNOTSUPP);
 
-	xdp_rxq->mem.type = type;
+	mem->type = type;
 
 	if (!allocator) {
 		if (type == MEM_TYPE_PAGE_POOL)
-			return -EINVAL; /* Setup time check page_pool req */
-		return 0;
+			return ERR_PTR(-EINVAL); /* Setup time check page_pool req */
+		return NULL;
 	}
 
 	/* Delay init of rhashtable to save memory if feature isn't used */
@@ -290,15 +290,13 @@
 		mutex_lock(&mem_id_lock);
 		ret = __mem_id_init_hash_table();
 		mutex_unlock(&mem_id_lock);
-		if (ret < 0) {
-			WARN_ON(1);
-			return ret;
-		}
+		if (ret < 0)
+			return ERR_PTR(ret);
 	}
 
 	xdp_alloc = kzalloc(sizeof(*xdp_alloc), gfp);
 	if (!xdp_alloc)
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
 
 	mutex_lock(&mem_id_lock);
 	id = __mem_id_cyclic_get(gfp);
@@ -306,15 +304,15 @@
 		errno = id;
 		goto err;
 	}
-	xdp_rxq->mem.id = id;
-	xdp_alloc->mem  = xdp_rxq->mem;
+	mem->id = id;
+	xdp_alloc->mem = *mem;
 	xdp_alloc->allocator = allocator;
 
 	/* Insert allocator into ID lookup table */
 	ptr = rhashtable_insert_slow(mem_id_ht, &id, &xdp_alloc->node);
 	if (IS_ERR(ptr)) {
-		ida_simple_remove(&mem_id_pool, xdp_rxq->mem.id);
-		xdp_rxq->mem.id = 0;
+		ida_simple_remove(&mem_id_pool, mem->id);
+		mem->id = 0;
 		errno = PTR_ERR(ptr);
 		goto err;
 	}
@@ -324,13 +322,44 @@
 
 	mutex_unlock(&mem_id_lock);
 
-	trace_mem_connect(xdp_alloc, xdp_rxq);
-	return 0;
+	return xdp_alloc;
 err:
 	mutex_unlock(&mem_id_lock);
 	kfree(xdp_alloc);
-	return errno;
+	return ERR_PTR(errno);
+}
+
+int xdp_reg_mem_model(struct xdp_mem_info *mem,
+		      enum xdp_mem_type type, void *allocator)
+{
+	struct xdp_mem_allocator *xdp_alloc;
+
+	xdp_alloc = __xdp_reg_mem_model(mem, type, allocator);
+	if (IS_ERR(xdp_alloc))
+		return PTR_ERR(xdp_alloc);
+	return 0;
 }
+EXPORT_SYMBOL_GPL(xdp_reg_mem_model);
+
+int xdp_rxq_info_reg_mem_model(struct xdp_rxq_info *xdp_rxq,
+			       enum xdp_mem_type type, void *allocator)
+{
+	struct xdp_mem_allocator *xdp_alloc;
+
+	if (xdp_rxq->reg_state != REG_STATE_REGISTERED) {
+		WARN(1, "Missing register, driver bug");
+		return -EFAULT;
+	}
+
+	xdp_alloc = __xdp_reg_mem_model(&xdp_rxq->mem, type, allocator);
+	if (IS_ERR(xdp_alloc))
+		return PTR_ERR(xdp_alloc);
+
+	if (trace_mem_connect_enabled() && xdp_alloc)
+		trace_mem_connect(xdp_alloc, xdp_rxq);
+	return 0;
+}
+
 EXPORT_SYMBOL_GPL(xdp_rxq_info_reg_mem_model);
 
 /* XDP RX runs under NAPI protection, and in different delivery error
--- linux-xilinx-zynqmp-5.15.0.orig/net/dcb/dcbnl.c
+++ linux-xilinx-zynqmp-5.15.0/net/dcb/dcbnl.c
@@ -946,7 +946,7 @@
 		return -EOPNOTSUPP;
 
 	ret = nla_parse_nested_deprecated(data, DCB_BCN_ATTR_MAX,
-					  tb[DCB_ATTR_BCN], dcbnl_pfc_up_nest,
+					  tb[DCB_ATTR_BCN], dcbnl_bcn_nest,
 					  NULL);
 	if (ret)
 		return ret;
@@ -2073,8 +2073,52 @@
 }
 EXPORT_SYMBOL(dcb_ieee_getapp_default_prio_mask);
 
+static void dcbnl_flush_dev(struct net_device *dev)
+{
+	struct dcb_app_type *itr, *tmp;
+
+	spin_lock_bh(&dcb_lock);
+
+	list_for_each_entry_safe(itr, tmp, &dcb_app_list, list) {
+		if (itr->ifindex == dev->ifindex) {
+			list_del(&itr->list);
+			kfree(itr);
+		}
+	}
+
+	spin_unlock_bh(&dcb_lock);
+}
+
+static int dcbnl_netdevice_event(struct notifier_block *nb,
+				 unsigned long event, void *ptr)
+{
+	struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+
+	switch (event) {
+	case NETDEV_UNREGISTER:
+		if (!dev->dcbnl_ops)
+			return NOTIFY_DONE;
+
+		dcbnl_flush_dev(dev);
+
+		return NOTIFY_OK;
+	default:
+		return NOTIFY_DONE;
+	}
+}
+
+static struct notifier_block dcbnl_nb __read_mostly = {
+	.notifier_call  = dcbnl_netdevice_event,
+};
+
 static int __init dcbnl_init(void)
 {
+	int err;
+
+	err = register_netdevice_notifier(&dcbnl_nb);
+	if (err)
+		return err;
+
 	rtnl_register(PF_UNSPEC, RTM_GETDCB, dcb_doit, NULL, 0);
 	rtnl_register(PF_UNSPEC, RTM_SETDCB, dcb_doit, NULL, 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/dccp.h
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/dccp.h
@@ -48,7 +48,7 @@
 
 extern struct inet_hashinfo dccp_hashinfo;
 
-extern struct percpu_counter dccp_orphan_count;
+DECLARE_PER_CPU(unsigned int, dccp_orphan_count);
 
 void dccp_time_wait(struct sock *sk, int state, int timeo);
 
@@ -283,6 +283,7 @@
 int dccp_rcv_established(struct sock *sk, struct sk_buff *skb,
 			 const struct dccp_hdr *dh, const unsigned int len);
 
+void dccp_destruct_common(struct sock *sk);
 int dccp_init_sock(struct sock *sk, const __u8 ctl_sock_initialized);
 void dccp_destroy_sock(struct sock *sk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/feat.c
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/feat.c
@@ -1166,8 +1166,12 @@
 			goto not_valid_or_not_known;
 		}
 
-		return dccp_feat_push_confirm(fn, feat, local, &fval);
+		if (dccp_feat_push_confirm(fn, feat, local, &fval)) {
+			kfree(fval.sp.vec);
+			return DCCP_RESET_CODE_TOO_BUSY;
+		}
 
+		return 0;
 	} else if (entry->state == FEAT_UNSTABLE) {	/* 6.6.2 */
 		return 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/ipv4.c
@@ -137,6 +137,8 @@
 	 * This unhashes the socket and releases the local port, if necessary.
 	 */
 	dccp_set_state(sk, DCCP_CLOSED);
+	if (!(sk->sk_userlocks & SOCK_BINDADDR_LOCK))
+		inet_reset_saddr(sk);
 	ip_rt_put(rt);
 	sk->sk_route_caps = 0;
 	inet->inet_dport = 0;
@@ -248,12 +250,12 @@
 	int err;
 	struct net *net = dev_net(skb->dev);
 
-	/* Only need dccph_dport & dccph_sport which are the first
-	 * 4 bytes in dccp header.
-	 * Our caller (icmp_socket_deliver()) already pulled 8 bytes for us.
-	 */
-	BUILD_BUG_ON(offsetofend(struct dccp_hdr, dccph_sport) > 8);
-	BUILD_BUG_ON(offsetofend(struct dccp_hdr, dccph_dport) > 8);
+	if (!pskb_may_pull(skb, offset + sizeof(*dh)))
+		return -EINVAL;
+	dh = (struct dccp_hdr *)(skb->data + offset);
+	if (!pskb_may_pull(skb, offset + __dccp_basic_hdr_len(dh)))
+		return -EINVAL;
+	iph = (struct iphdr *)skb->data;
 	dh = (struct dccp_hdr *)(skb->data + offset);
 
 	sk = __inet_lookup_established(net, &dccp_hashinfo,
@@ -621,9 +623,6 @@
 	if (dccp_parse_options(sk, dreq, skb))
 		goto drop_and_free;
 
-	if (security_inet_conn_request(sk, skb, req))
-		goto drop_and_free;
-
 	ireq = inet_rsk(req);
 	sk_rcv_saddr_set(req_to_sk(req), ip_hdr(skb)->daddr);
 	sk_daddr_set(req_to_sk(req), ip_hdr(skb)->saddr);
@@ -631,6 +630,9 @@
 	ireq->ireq_family = AF_INET;
 	ireq->ir_iif = sk->sk_bound_dev_if;
 
+	if (security_inet_conn_request(sk, skb, req))
+		goto drop_and_free;
+
 	/*
 	 * Step 3: Process LISTEN state
 	 *
@@ -647,8 +649,11 @@
 	if (dccp_v4_send_response(sk, req))
 		goto drop_and_free;
 
-	inet_csk_reqsk_queue_hash_add(sk, req, DCCP_TIMEOUT_INIT);
-	reqsk_put(req);
+	if (unlikely(!inet_csk_reqsk_queue_hash_add(sk, req, DCCP_TIMEOUT_INIT)))
+		reqsk_free(req);
+	else
+		reqsk_put(req);
+
 	return 0;
 
 drop_and_free:
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/ipv6.c
@@ -74,7 +74,7 @@
 static int dccp_v6_err(struct sk_buff *skb, struct inet6_skb_parm *opt,
 			u8 type, u8 code, int offset, __be32 info)
 {
-	const struct ipv6hdr *hdr = (const struct ipv6hdr *)skb->data;
+	const struct ipv6hdr *hdr;
 	const struct dccp_hdr *dh;
 	struct dccp_sock *dp;
 	struct ipv6_pinfo *np;
@@ -83,12 +83,12 @@
 	__u64 seq;
 	struct net *net = dev_net(skb->dev);
 
-	/* Only need dccph_dport & dccph_sport which are the first
-	 * 4 bytes in dccp header.
-	 * Our caller (icmpv6_notify()) already pulled 8 bytes for us.
-	 */
-	BUILD_BUG_ON(offsetofend(struct dccp_hdr, dccph_sport) > 8);
-	BUILD_BUG_ON(offsetofend(struct dccp_hdr, dccph_dport) > 8);
+	if (!pskb_may_pull(skb, offset + sizeof(*dh)))
+		return -EINVAL;
+	dh = (struct dccp_hdr *)(skb->data + offset);
+	if (!pskb_may_pull(skb, offset + __dccp_basic_hdr_len(dh)))
+		return -EINVAL;
+	hdr = (const struct ipv6hdr *)skb->data;
 	dh = (struct dccp_hdr *)(skb->data + offset);
 
 	sk = __inet6_lookup_established(net, &dccp_hashinfo,
@@ -359,15 +359,15 @@
 	if (dccp_parse_options(sk, dreq, skb))
 		goto drop_and_free;
 
-	if (security_inet_conn_request(sk, skb, req))
-		goto drop_and_free;
-
 	ireq = inet_rsk(req);
 	ireq->ir_v6_rmt_addr = ipv6_hdr(skb)->saddr;
 	ireq->ir_v6_loc_addr = ipv6_hdr(skb)->daddr;
 	ireq->ireq_family = AF_INET6;
 	ireq->ir_mark = inet_request_mark(sk, skb);
 
+	if (security_inet_conn_request(sk, skb, req))
+		goto drop_and_free;
+
 	if (ipv6_opt_accepted(sk, skb, IP6CB(skb)) ||
 	    np->rxopt.bits.rxinfo || np->rxopt.bits.rxoinfo ||
 	    np->rxopt.bits.rxhlim || np->rxopt.bits.rxohlim) {
@@ -397,8 +397,11 @@
 	if (dccp_v6_send_response(sk, req))
 		goto drop_and_free;
 
-	inet_csk_reqsk_queue_hash_add(sk, req, DCCP_TIMEOUT_INIT);
-	reqsk_put(req);
+	if (unlikely(!inet_csk_reqsk_queue_hash_add(sk, req, DCCP_TIMEOUT_INIT)))
+		reqsk_free(req);
+	else
+		reqsk_put(req);
+
 	return 0;
 
 drop_and_free:
@@ -551,11 +554,9 @@
 	*own_req = inet_ehash_nolisten(newsk, req_to_sk(req_unhash), NULL);
 	/* Clone pktoptions received with SYN, if we own the req */
 	if (*own_req && ireq->pktopts) {
-		newnp->pktoptions = skb_clone(ireq->pktopts, GFP_ATOMIC);
+		newnp->pktoptions = skb_clone_and_charge_r(ireq->pktopts, newsk);
 		consume_skb(ireq->pktopts);
 		ireq->pktopts = NULL;
-		if (newnp->pktoptions)
-			skb_set_owner_r(newnp->pktoptions, newsk);
 	}
 
 	return newsk;
@@ -614,8 +615,8 @@
 	   by tcp. Feel free to propose better solution.
 					       --ANK (980728)
 	 */
-	if (np->rxopt.all)
-		opt_skb = skb_clone(skb, GFP_ATOMIC);
+	if (np->rxopt.all && sk->sk_state != DCCP_LISTEN)
+		opt_skb = skb_clone_and_charge_r(skb, sk);
 
 	if (sk->sk_state == DCCP_OPEN) { /* Fast path */
 		if (dccp_rcv_established(sk, skb, dccp_hdr(skb), skb->len))
@@ -679,7 +680,6 @@
 			np->flow_label = ip6_flowlabel(ipv6_hdr(opt_skb));
 		if (ipv6_opt_accepted(sk, opt_skb,
 				      &DCCP_SKB_CB(opt_skb)->header.h6)) {
-			skb_set_owner_r(opt_skb, sk);
 			memmove(IP6CB(opt_skb),
 				&DCCP_SKB_CB(opt_skb)->header.h6,
 				sizeof(struct inet6_skb_parm));
@@ -967,6 +967,8 @@
 
 late_failure:
 	dccp_set_state(sk, DCCP_CLOSED);
+	if (!(sk->sk_userlocks & SOCK_BINDADDR_LOCK))
+		inet_reset_saddr(sk);
 	__sk_dst_reset(sk);
 failure:
 	inet->inet_dport = 0;
@@ -1003,6 +1005,12 @@
 	.sockaddr_len	   = sizeof(struct sockaddr_in6),
 };
 
+static void dccp_v6_sk_destruct(struct sock *sk)
+{
+	dccp_destruct_common(sk);
+	inet6_sock_destruct(sk);
+}
+
 /* NOTE: A lot of things set to zero explicitly by call to
  *       sk_alloc() so need not be done here.
  */
@@ -1015,17 +1023,12 @@
 		if (unlikely(!dccp_v6_ctl_sock_initialized))
 			dccp_v6_ctl_sock_initialized = 1;
 		inet_csk(sk)->icsk_af_ops = &dccp_ipv6_af_ops;
+		sk->sk_destruct = dccp_v6_sk_destruct;
 	}
 
 	return err;
 }
 
-static void dccp_v6_destroy_sock(struct sock *sk)
-{
-	dccp_destroy_sock(sk);
-	inet6_destroy_sock(sk);
-}
-
 static struct timewait_sock_ops dccp6_timewait_sock_ops = {
 	.twsk_obj_size	= sizeof(struct dccp6_timewait_sock),
 };
@@ -1048,7 +1051,7 @@
 	.accept		   = inet_csk_accept,
 	.get_port	   = inet_csk_get_port,
 	.shutdown	   = dccp_shutdown,
-	.destroy	   = dccp_v6_destroy_sock,
+	.destroy	   = dccp_destroy_sock,
 	.orphan_count	   = &dccp_orphan_count,
 	.max_header	   = MAX_DCCP_HEADER,
 	.obj_size	   = sizeof(struct dccp6_sock),
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/minisocks.c
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/minisocks.c
@@ -93,6 +93,8 @@
 
 		newdp->dccps_role	    = DCCP_ROLE_SERVER;
 		newdp->dccps_hc_rx_ackvec   = NULL;
+		newdp->dccps_hc_rx_ccid = NULL;
+		newdp->dccps_hc_tx_ccid = NULL;
 		newdp->dccps_service_list   = NULL;
 		newdp->dccps_hc_rx_ccid     = NULL;
 		newdp->dccps_hc_tx_ccid     = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/output.c
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/output.c
@@ -187,7 +187,7 @@
 
 	/* And store cached results */
 	icsk->icsk_pmtu_cookie = pmtu;
-	dp->dccps_mss_cache = cur_mps;
+	WRITE_ONCE(dp->dccps_mss_cache, cur_mps);
 
 	return cur_mps;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/dccp/proto.c
+++ linux-xilinx-zynqmp-5.15.0/net/dccp/proto.c
@@ -42,8 +42,8 @@
 
 EXPORT_SYMBOL_GPL(dccp_statistics);
 
-struct percpu_counter dccp_orphan_count;
-EXPORT_SYMBOL_GPL(dccp_orphan_count);
+DEFINE_PER_CPU(unsigned int, dccp_orphan_count);
+EXPORT_PER_CPU_SYMBOL_GPL(dccp_orphan_count);
 
 struct inet_hashinfo dccp_hashinfo;
 EXPORT_SYMBOL_GPL(dccp_hashinfo);
@@ -171,12 +171,18 @@
 
 EXPORT_SYMBOL_GPL(dccp_packet_name);
 
-static void dccp_sk_destruct(struct sock *sk)
+void dccp_destruct_common(struct sock *sk)
 {
 	struct dccp_sock *dp = dccp_sk(sk);
 
 	ccid_hc_tx_delete(dp->dccps_hc_tx_ccid, sk);
 	dp->dccps_hc_tx_ccid = NULL;
+}
+EXPORT_SYMBOL_GPL(dccp_destruct_common);
+
+static void dccp_sk_destruct(struct sock *sk)
+{
+	dccp_destruct_common(sk);
 	inet_sock_destruct(sk);
 }
 
@@ -318,11 +324,15 @@
 __poll_t dccp_poll(struct file *file, struct socket *sock,
 		       poll_table *wait)
 {
-	__poll_t mask;
 	struct sock *sk = sock->sk;
+	__poll_t mask;
+	u8 shutdown;
+	int state;
 
 	sock_poll_wait(file, sock, wait);
-	if (sk->sk_state == DCCP_LISTEN)
+
+	state = inet_sk_state_load(sk);
+	if (state == DCCP_LISTEN)
 		return inet_csk_listen_poll(sk);
 
 	/* Socket is not locked. We are protected from async events
@@ -331,20 +341,21 @@
 	 */
 
 	mask = 0;
-	if (sk->sk_err)
+	if (READ_ONCE(sk->sk_err))
 		mask = EPOLLERR;
+	shutdown = READ_ONCE(sk->sk_shutdown);
 
-	if (sk->sk_shutdown == SHUTDOWN_MASK || sk->sk_state == DCCP_CLOSED)
+	if (shutdown == SHUTDOWN_MASK || state == DCCP_CLOSED)
 		mask |= EPOLLHUP;
-	if (sk->sk_shutdown & RCV_SHUTDOWN)
+	if (shutdown & RCV_SHUTDOWN)
 		mask |= EPOLLIN | EPOLLRDNORM | EPOLLRDHUP;
 
 	/* Connected? */
-	if ((1 << sk->sk_state) & ~(DCCPF_REQUESTING | DCCPF_RESPOND)) {
+	if ((1 << state) & ~(DCCPF_REQUESTING | DCCPF_RESPOND)) {
 		if (atomic_read(&sk->sk_rmem_alloc) > 0)
 			mask |= EPOLLIN | EPOLLRDNORM;
 
-		if (!(sk->sk_shutdown & SEND_SHUTDOWN)) {
+		if (!(shutdown & SEND_SHUTDOWN)) {
 			if (sk_stream_is_writeable(sk)) {
 				mask |= EPOLLOUT | EPOLLWRNORM;
 			} else {  /* send SIGIO later */
@@ -362,7 +373,6 @@
 	}
 	return mask;
 }
-
 EXPORT_SYMBOL_GPL(dccp_poll);
 
 int dccp_ioctl(struct sock *sk, int cmd, unsigned long arg)
@@ -633,7 +643,7 @@
 		return dccp_getsockopt_service(sk, len,
 					       (__be32 __user *)optval, optlen);
 	case DCCP_SOCKOPT_GET_CUR_MPS:
-		val = dp->dccps_mss_cache;
+		val = READ_ONCE(dp->dccps_mss_cache);
 		break;
 	case DCCP_SOCKOPT_AVAILABLE_CCIDS:
 		return ccid_getsockopt_builtin_ccids(sk, len, optval, optlen);
@@ -742,16 +752,11 @@
 
 	trace_dccp_probe(sk, len);
 
-	if (len > dp->dccps_mss_cache)
+	if (len > READ_ONCE(dp->dccps_mss_cache))
 		return -EMSGSIZE;
 
 	lock_sock(sk);
 
-	if (dccp_qpolicy_full(sk)) {
-		rc = -EAGAIN;
-		goto out_release;
-	}
-
 	timeo = sock_sndtimeo(sk, noblock);
 
 	/*
@@ -770,11 +775,22 @@
 	if (skb == NULL)
 		goto out_release;
 
+	if (dccp_qpolicy_full(sk)) {
+		rc = -EAGAIN;
+		goto out_discard;
+	}
+
 	if (sk->sk_state == DCCP_CLOSED) {
 		rc = -ENOTCONN;
 		goto out_discard;
 	}
 
+	/* We need to check dccps_mss_cache after socket is locked. */
+	if (len > dp->dccps_mss_cache) {
+		rc = -EMSGSIZE;
+		goto out_discard;
+	}
+
 	skb_reserve(skb, sk->sk_prot->max_header);
 	rc = memcpy_from_msg(skb_put(skb, len), msg, len);
 	if (rc != 0)
@@ -1055,7 +1071,7 @@
 	bh_lock_sock(sk);
 	WARN_ON(sock_owned_by_user(sk));
 
-	percpu_counter_inc(sk->sk_prot->orphan_count);
+	this_cpu_inc(dccp_orphan_count);
 
 	/* Have we already been destroyed by a softirq or backlog? */
 	if (state != DCCP_CLOSED && sk->sk_state == DCCP_CLOSED)
@@ -1115,13 +1131,9 @@
 
 	BUILD_BUG_ON(sizeof(struct dccp_skb_cb) >
 		     sizeof_field(struct sk_buff, cb));
-	rc = percpu_counter_init(&dccp_orphan_count, 0, GFP_KERNEL);
-	if (rc)
-		goto out_fail;
-	inet_hashinfo_init(&dccp_hashinfo);
 	rc = inet_hashinfo2_init_mod(&dccp_hashinfo);
 	if (rc)
-		goto out_free_percpu;
+		goto out_fail;
 	rc = -ENOBUFS;
 	dccp_hashinfo.bind_bucket_cachep =
 		kmem_cache_create("dccp_bind_bucket",
@@ -1226,8 +1238,6 @@
 	kmem_cache_destroy(dccp_hashinfo.bind_bucket_cachep);
 out_free_hashinfo2:
 	inet_hashinfo2_free_mod(&dccp_hashinfo);
-out_free_percpu:
-	percpu_counter_destroy(&dccp_orphan_count);
 out_fail:
 	dccp_hashinfo.bhash = NULL;
 	dccp_hashinfo.ehash = NULL;
@@ -1250,7 +1260,6 @@
 	dccp_ackvec_exit();
 	dccp_sysctl_exit();
 	inet_hashinfo2_free_mod(&dccp_hashinfo);
-	percpu_counter_destroy(&dccp_orphan_count);
 }
 
 module_init(dccp_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/dns_resolver/dns_key.c
+++ linux-xilinx-zynqmp-5.15.0/net/dns_resolver/dns_key.c
@@ -91,7 +91,6 @@
 static int
 dns_resolver_preparse(struct key_preparsed_payload *prep)
 {
-	const struct dns_payload_header *bin;
 	struct user_key_payload *upayload;
 	unsigned long derrno;
 	int ret;
@@ -102,26 +101,34 @@
 		return -EINVAL;
 
 	if (data[0] == 0) {
+		const struct dns_server_list_v1_header *v1;
+
 		/* It may be a server list. */
-		if (datalen <= sizeof(*bin))
+		if (datalen < sizeof(*v1))
 			return -EINVAL;
 
-		bin = (const struct dns_payload_header *)data;
-		kenter("[%u,%u],%u", bin->content, bin->version, datalen);
-		if (bin->content != DNS_PAYLOAD_IS_SERVER_LIST) {
+		v1 = (const struct dns_server_list_v1_header *)data;
+		kenter("[%u,%u],%u", v1->hdr.content, v1->hdr.version, datalen);
+		if (v1->hdr.content != DNS_PAYLOAD_IS_SERVER_LIST) {
 			pr_warn_ratelimited(
 				"dns_resolver: Unsupported content type (%u)\n",
-				bin->content);
+				v1->hdr.content);
 			return -EINVAL;
 		}
 
-		if (bin->version != 1) {
+		if (v1->hdr.version != 1) {
 			pr_warn_ratelimited(
 				"dns_resolver: Unsupported server list version (%u)\n",
-				bin->version);
+				v1->hdr.version);
 			return -EINVAL;
 		}
 
+		if ((v1->status != DNS_LOOKUP_GOOD &&
+		     v1->status != DNS_LOOKUP_GOOD_WITH_BAD)) {
+			if (prep->expiry == TIME64_MAX)
+				prep->expiry = ktime_get_real_seconds() + 1;
+		}
+
 		result_len = datalen;
 		goto store_result;
 	}
@@ -314,7 +321,7 @@
 
 struct key_type key_type_dns_resolver = {
 	.name		= "dns_resolver",
-	.flags		= KEY_TYPE_NET_DOMAIN,
+	.flags		= KEY_TYPE_NET_DOMAIN | KEY_TYPE_INSTANT_REAP,
 	.preparse	= dns_resolver_preparse,
 	.free_preparse	= dns_resolver_free_preparse,
 	.instantiate	= generic_key_instantiate,
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/dsa2.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/dsa2.c
@@ -386,6 +386,24 @@
 	return 0;
 }
 
+static struct dsa_port *
+dsa_switch_preferred_default_local_cpu_port(struct dsa_switch *ds)
+{
+	struct dsa_port *cpu_dp;
+
+	if (!ds->ops->preferred_default_local_cpu_port)
+		return NULL;
+
+	cpu_dp = ds->ops->preferred_default_local_cpu_port(ds);
+	if (!cpu_dp)
+		return NULL;
+
+	if (WARN_ON(!dsa_port_is_cpu(cpu_dp) || cpu_dp->ds != ds))
+		return NULL;
+
+	return cpu_dp;
+}
+
 /* Perform initial assignment of CPU ports to user ports and DSA links in the
  * fabric, giving preference to CPU ports local to each switch. Default to
  * using the first CPU port in the switch tree if the port does not have a CPU
@@ -393,12 +411,16 @@
  */
 static int dsa_tree_setup_cpu_ports(struct dsa_switch_tree *dst)
 {
-	struct dsa_port *cpu_dp, *dp;
+	struct dsa_port *preferred_cpu_dp, *cpu_dp, *dp;
 
 	list_for_each_entry(cpu_dp, &dst->ports, list) {
 		if (!dsa_port_is_cpu(cpu_dp))
 			continue;
 
+		preferred_cpu_dp = dsa_switch_preferred_default_local_cpu_port(cpu_dp->ds);
+		if (preferred_cpu_dp && preferred_cpu_dp != cpu_dp)
+			continue;
+
 		list_for_each_entry(dp, &dst->ports, list) {
 			/* Prefer a local CPU port */
 			if (dp->ds != cpu_dp->ds)
@@ -1253,9 +1275,9 @@
 static int dsa_port_parse_cpu(struct dsa_port *dp, struct net_device *master,
 			      const char *user_protocol)
 {
+	const struct dsa_device_ops *tag_ops = NULL;
 	struct dsa_switch *ds = dp->ds;
 	struct dsa_switch_tree *dst = ds->dst;
-	const struct dsa_device_ops *tag_ops;
 	enum dsa_tag_protocol default_proto;
 
 	/* Find out which protocol the switch would prefer. */
@@ -1278,10 +1300,17 @@
 		}
 
 		tag_ops = dsa_find_tagger_by_name(user_protocol);
-	} else {
-		tag_ops = dsa_tag_driver_get(default_proto);
+		if (IS_ERR(tag_ops)) {
+			dev_warn(ds->dev,
+				 "Failed to find a tagging driver for protocol %s, using default\n",
+				 user_protocol);
+			tag_ops = NULL;
+		}
 	}
 
+	if (!tag_ops)
+		tag_ops = dsa_tag_driver_get(default_proto);
+
 	if (IS_ERR(tag_ops)) {
 		if (PTR_ERR(tag_ops) == -ENOPROTOOPT)
 			return -EPROBE_DEFER;
@@ -1341,6 +1370,7 @@
 		const char *user_protocol;
 
 		master = of_find_net_device_by_node(ethernet);
+		of_node_put(ethernet);
 		if (!master)
 			return -EPROBE_DEFER;
 
@@ -1626,12 +1656,21 @@
 void dsa_switch_shutdown(struct dsa_switch *ds)
 {
 	struct net_device *master, *slave_dev;
-	LIST_HEAD(unregister_list);
+	LIST_HEAD(close_list);
 	struct dsa_port *dp;
 
 	mutex_lock(&dsa2_mutex);
+
+	if (!ds->setup)
+		goto out;
+
 	rtnl_lock();
 
+	dsa_switch_for_each_cpu_port(dp, ds)
+		list_add(&dp->master->close_list, &close_list);
+
+	dev_close_many(&close_list, true);
+
 	list_for_each_entry(dp, &ds->dst->ports, list) {
 		if (dp->ds != ds)
 			continue;
@@ -1642,28 +1681,18 @@
 		master = dp->cpu_dp->master;
 		slave_dev = dp->slave;
 
+		netif_device_detach(slave_dev);
 		netdev_upper_dev_unlink(master, slave_dev);
-		/* Just unlinking ourselves as uppers of the master is not
-		 * sufficient. When the master net device unregisters, that will
-		 * also call dev_close, which we will catch as NETDEV_GOING_DOWN
-		 * and trigger a dev_close on our own devices (dsa_slave_close).
-		 * In turn, that will call dev_mc_unsync on the master's net
-		 * device. If the master is also a DSA switch port, this will
-		 * trigger dsa_slave_set_rx_mode which will call dev_mc_sync on
-		 * its own master. Lockdep will complain about the fact that
-		 * all cascaded masters have the same dsa_master_addr_list_lock_key,
-		 * which it normally would not do if the cascaded masters would
-		 * be in a proper upper/lower relationship, which we've just
-		 * destroyed.
-		 * To suppress the lockdep warnings, let's actually unregister
-		 * the DSA slave interfaces too, to avoid the nonsensical
-		 * multicast address list synchronization on shutdown.
-		 */
-		unregister_netdevice_queue(slave_dev, &unregister_list);
 	}
-	unregister_netdevice_many(&unregister_list);
+
+	/* Disconnect from further netdevice notifiers on the master,
+	 * since netdev_uses_dsa() will now return false.
+	 */
+	dsa_switch_for_each_cpu_port(dp, ds)
+		dp->master->dsa_ptr = NULL;
 
 	rtnl_unlock();
+out:
 	mutex_unlock(&dsa2_mutex);
 }
 EXPORT_SYMBOL_GPL(dsa_switch_shutdown);
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/dsa_priv.h
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/dsa_priv.h
@@ -198,6 +198,7 @@
 }
 
 /* port.c */
+bool dsa_port_supports_hwtstamp(struct dsa_port *dp, struct ifreq *ifr);
 void dsa_port_set_tag_protocol(struct dsa_port *cpu_dp,
 			       const struct dsa_device_ops *tag_ops);
 int dsa_port_set_state(struct dsa_port *dp, u8 state, bool do_fast_age);
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/master.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/master.c
@@ -204,8 +204,7 @@
 		 * switch in the tree that is PTP capable.
 		 */
 		list_for_each_entry(dp, &dst->ports, list)
-			if (dp->ds->ops->port_hwtstamp_get ||
-			    dp->ds->ops->port_hwtstamp_set)
+			if (dsa_port_supports_hwtstamp(dp, ifr))
 				return -EBUSY;
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/port.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/port.c
@@ -75,6 +75,22 @@
 	return !err;
 }
 
+bool dsa_port_supports_hwtstamp(struct dsa_port *dp, struct ifreq *ifr)
+{
+	struct dsa_switch *ds = dp->ds;
+	int err;
+
+	if (!ds->ops->port_hwtstamp_get || !ds->ops->port_hwtstamp_set)
+		return false;
+
+	/* "See through" shim implementations of the "get" method.
+	 * This will clobber the ifreq structure, but we will either return an
+	 * error, or the master will overwrite it with proper values.
+	 */
+	err = ds->ops->port_hwtstamp_get(ds, dp->index, ifr);
+	return err != -EOPNOTSUPP;
+}
+
 int dsa_port_set_state(struct dsa_port *dp, u8 state, bool do_fast_age)
 {
 	struct dsa_switch *ds = dp->ds;
@@ -111,11 +127,14 @@
 static void dsa_port_set_state_now(struct dsa_port *dp, u8 state,
 				   bool do_fast_age)
 {
+	struct dsa_switch *ds = dp->ds;
 	int err;
 
 	err = dsa_port_set_state(dp, state, do_fast_age);
-	if (err)
-		pr_err("DSA: failed to set STP state %u (%d)\n", state, err);
+	if (err && err != -EOPNOTSUPP) {
+		dev_err(ds->dev, "port %d failed to set STP state %u: %pe\n",
+			dp->index, state, ERR_PTR(err));
+	}
 }
 
 int dsa_port_enable_rt(struct dsa_port *dp, struct phy_device *phy)
@@ -1201,8 +1220,10 @@
 			if (ds->ops->phylink_mac_link_down)
 				ds->ops->phylink_mac_link_down(ds, port,
 					MLO_AN_FIXED, PHY_INTERFACE_MODE_NA);
+			of_node_put(phy_np);
 			return dsa_port_phylink_register(dp);
 		}
+		of_node_put(phy_np);
 		return 0;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/slave.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/slave.c
@@ -174,7 +174,7 @@
 		dev_uc_del(master, dev->dev_addr);
 
 out:
-	ether_addr_copy(dev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(dev, addr->sa_data);
 
 	return 0;
 }
@@ -803,6 +803,40 @@
 	net_selftest(ndev, etest, buf);
 }
 
+static int dsa_slave_get_mm(struct net_device *dev,
+			    struct ethtool_mm_state *state)
+{
+	struct dsa_port *dp = dsa_slave_to_port(dev);
+	struct dsa_switch *ds = dp->ds;
+
+	if (!ds->ops->get_mm)
+		return -EOPNOTSUPP;
+
+	return ds->ops->get_mm(ds, dp->index, state);
+}
+
+static int dsa_slave_set_mm(struct net_device *dev, struct ethtool_mm_cfg *cfg,
+			    struct netlink_ext_ack *extack)
+{
+	struct dsa_port *dp = dsa_slave_to_port(dev);
+	struct dsa_switch *ds = dp->ds;
+
+	if (!ds->ops->set_mm)
+		return -EOPNOTSUPP;
+
+	return ds->ops->set_mm(ds, dp->index, cfg, extack);
+}
+
+static void dsa_slave_get_mm_stats(struct net_device *dev,
+				   struct ethtool_mm_stats *stats)
+{
+	struct dsa_port *dp = dsa_slave_to_port(dev);
+	struct dsa_switch *ds = dp->ds;
+
+	if (ds->ops->get_mm_stats)
+		ds->ops->get_mm_stats(ds, dp->index, stats);
+}
+
 static void dsa_slave_get_wol(struct net_device *dev, struct ethtool_wolinfo *w)
 {
 	struct dsa_port *dp = dsa_slave_to_port(dev);
@@ -1707,6 +1741,9 @@
 	.set_rxnfc		= dsa_slave_set_rxnfc,
 	.get_ts_info		= dsa_slave_get_ts_info,
 	.self_test		= dsa_slave_net_selftest,
+	.get_mm			= dsa_slave_get_mm,
+	.set_mm			= dsa_slave_set_mm,
+	.get_mm_stats		= dsa_slave_get_mm_stats,
 };
 
 static struct devlink_port *dsa_slave_get_devlink_port(struct net_device *dev)
@@ -1954,7 +1991,7 @@
 
 	slave_dev->ethtool_ops = &dsa_slave_ethtool_ops;
 	if (!is_zero_ether_addr(port->mac))
-		ether_addr_copy(slave_dev->dev_addr, port->mac);
+		eth_hw_addr_set(slave_dev, port->mac);
 	else
 		eth_hw_addr_inherit(slave_dev, master);
 	slave_dev->priv_flags |= IFF_NO_QUEUE;
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/switch.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/switch.c
@@ -264,7 +264,7 @@
 
 	err = ds->ops->port_mdb_del(ds, port, mdb);
 	if (err) {
-		refcount_inc(&a->refcount);
+		refcount_set(&a->refcount, 1);
 		return err;
 	}
 
@@ -329,7 +329,7 @@
 
 	err = ds->ops->port_fdb_del(ds, port, addr, vid);
 	if (err) {
-		refcount_inc(&a->refcount);
+		refcount_set(&a->refcount, 1);
 		return err;
 	}
 
@@ -644,7 +644,7 @@
 dsa_switch_mrp_add_ring_role(struct dsa_switch *ds,
 			     struct dsa_notifier_mrp_ring_role_info *info)
 {
-	if (!ds->ops->port_mrp_add)
+	if (!ds->ops->port_mrp_add_ring_role)
 		return -EOPNOTSUPP;
 
 	if (ds->index == info->sw_index)
@@ -658,7 +658,7 @@
 dsa_switch_mrp_del_ring_role(struct dsa_switch *ds,
 			     struct dsa_notifier_mrp_ring_role_info *info)
 {
-	if (!ds->ops->port_mrp_del)
+	if (!ds->ops->port_mrp_del_ring_role)
 		return -EOPNOTSUPP;
 
 	if (ds->index == info->sw_index)
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_8021q.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_8021q.c
@@ -529,6 +529,7 @@
 int dsa_tag_8021q_register(struct dsa_switch *ds, __be16 proto)
 {
 	struct dsa_8021q_context *ctx;
+	int err;
 
 	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
 	if (!ctx)
@@ -541,7 +542,15 @@
 
 	ds->tag_8021q_ctx = ctx;
 
-	return dsa_tag_8021q_setup(ds);
+	err = dsa_tag_8021q_setup(ds);
+	if (err)
+		goto err_free;
+
+	return 0;
+
+err_free:
+	kfree(ctx);
+	return err;
 }
 EXPORT_SYMBOL_GPL(dsa_tag_8021q_register);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_brcm.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_brcm.c
@@ -7,6 +7,7 @@
 
 #include <linux/dsa/brcm.h>
 #include <linux/etherdevice.h>
+#include <linux/if_vlan.h>
 #include <linux/list.h>
 #include <linux/slab.h>
 
@@ -248,6 +249,7 @@
 static struct sk_buff *brcm_leg_tag_rcv(struct sk_buff *skb,
 					struct net_device *dev)
 {
+	int len = BRCM_LEG_TAG_LEN;
 	int source_port;
 	u8 *brcm_tag;
 
@@ -262,12 +264,16 @@
 	if (!skb->dev)
 		return NULL;
 
+	/* VLAN tag is added by BCM63xx internal switch */
+	if (netdev_uses_dsa(skb->dev))
+		len += VLAN_HLEN;
+
 	/* Remove Broadcom tag and update checksum */
-	skb_pull_rcsum(skb, BRCM_LEG_TAG_LEN);
+	skb_pull_rcsum(skb, len);
 
 	dsa_default_offload_fwd_mark(skb);
 
-	dsa_strip_etype_header(skb, BRCM_LEG_TAG_LEN);
+	dsa_strip_etype_header(skb, len);
 
 	return skb;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_hellcreek.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_hellcreek.c
@@ -21,6 +21,14 @@
 	struct dsa_port *dp = dsa_slave_to_port(dev);
 	u8 *tag;
 
+	/* Calculate checksums (if required) before adding the trailer tag to
+	 * avoid including it in calculations. That would lead to wrong
+	 * checksums after the switch strips the tag.
+	 */
+	if (skb->ip_summed == CHECKSUM_PARTIAL &&
+	    skb_checksum_help(skb))
+		return NULL;
+
 	/* Tag encoding */
 	tag  = skb_put(skb, HELLCREEK_TAG_LEN);
 	*tag = BIT(dp->index);
@@ -37,11 +45,12 @@
 
 	skb->dev = dsa_master_find_slave(dev, 0, port);
 	if (!skb->dev) {
-		netdev_warn(dev, "Failed to get source port: %d\n", port);
+		netdev_warn_once(dev, "Failed to get source port: %d\n", port);
 		return NULL;
 	}
 
-	pskb_trim_rcsum(skb, skb->len - HELLCREEK_TAG_LEN);
+	if (pskb_trim_rcsum(skb, skb->len - HELLCREEK_TAG_LEN))
+		return NULL;
 
 	dsa_default_offload_fwd_mark(skb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_ksz.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_ksz.c
@@ -22,7 +22,8 @@
 	if (!skb->dev)
 		return NULL;
 
-	pskb_trim_rcsum(skb, skb->len - len);
+	if (pskb_trim_rcsum(skb, skb->len - len))
+		return NULL;
 
 	dsa_default_offload_fwd_mark(skb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_lan9303.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_lan9303.c
@@ -77,7 +77,6 @@
 
 static struct sk_buff *lan9303_rcv(struct sk_buff *skb, struct net_device *dev)
 {
-	__be16 *lan9303_tag;
 	u16 lan9303_tag1;
 	unsigned int source_port;
 
@@ -87,14 +86,15 @@
 		return NULL;
 	}
 
-	lan9303_tag = dsa_etype_header_pos_rx(skb);
-
-	if (lan9303_tag[0] != htons(ETH_P_8021Q)) {
-		dev_warn_ratelimited(&dev->dev, "Dropping packet due to invalid VLAN marker\n");
-		return NULL;
+	if (skb_vlan_tag_present(skb)) {
+		lan9303_tag1 = skb_vlan_tag_get(skb);
+		__vlan_hwaccel_clear_tag(skb);
+	} else {
+		skb_push_rcsum(skb, ETH_HLEN);
+		__skb_vlan_pop(skb, &lan9303_tag1);
+		skb_pull_rcsum(skb, ETH_HLEN);
 	}
 
-	lan9303_tag1 = ntohs(lan9303_tag[1]);
 	source_port = lan9303_tag1 & 0x3;
 
 	skb->dev = dsa_master_find_slave(dev, 0, source_port);
@@ -103,13 +103,6 @@
 		return NULL;
 	}
 
-	/* remove the special VLAN tag between the MAC addresses
-	 * and the current ethertype field.
-	 */
-	skb_pull_rcsum(skb, 2 + 2);
-
-	dsa_strip_etype_header(skb, LAN9303_TAG_LEN);
-
 	if (!(lan9303_tag1 & LAN9303_TAG_RX_TRAPPED_TO_CPU))
 		dsa_default_offload_fwd_mark(skb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_ocelot.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_ocelot.c
@@ -62,6 +62,7 @@
 	struct dsa_port *dp;
 	u8 *extraction;
 	u16 vlan_tpid;
+	u64 rew_val;
 
 	/* Revert skb->data by the amount consumed by the DSA master,
 	 * so it points to the beginning of the frame.
@@ -91,6 +92,7 @@
 	ocelot_xfh_get_qos_class(extraction, &qos_class);
 	ocelot_xfh_get_tag_type(extraction, &tag_type);
 	ocelot_xfh_get_vlan_tci(extraction, &vlan_tci);
+	ocelot_xfh_get_rew_val(extraction, &rew_val);
 
 	skb->dev = dsa_master_find_slave(netdev, 0, src_port);
 	if (!skb->dev)
@@ -104,6 +106,7 @@
 
 	dsa_default_offload_fwd_mark(skb);
 	skb->priority = qos_class;
+	OCELOT_SKB_CB(skb)->tstamp_lo = rew_val;
 
 	/* Ocelot switches copy frames unmodified to the CPU. However, it is
 	 * possible for the user to request a VLAN modification through
--- linux-xilinx-zynqmp-5.15.0.orig/net/dsa/tag_sja1105.c
+++ linux-xilinx-zynqmp-5.15.0/net/dsa/tag_sja1105.c
@@ -100,8 +100,8 @@
 	 * a unified unpacking command for both device series.
 	 */
 	packing(buf,     &meta->tstamp,     31, 0, 4, UNPACK, 0);
-	packing(buf + 4, &meta->dmac_byte_4, 7, 0, 1, UNPACK, 0);
-	packing(buf + 5, &meta->dmac_byte_3, 7, 0, 1, UNPACK, 0);
+	packing(buf + 4, &meta->dmac_byte_3, 7, 0, 1, UNPACK, 0);
+	packing(buf + 5, &meta->dmac_byte_4, 7, 0, 1, UNPACK, 0);
 	packing(buf + 6, &meta->source_port, 7, 0, 1, UNPACK, 0);
 	packing(buf + 7, &meta->switch_id,   7, 0, 1, UNPACK, 0);
 }
@@ -489,10 +489,7 @@
 	is_link_local = sja1105_is_link_local(skb);
 	is_meta = sja1105_is_meta_frame(skb);
 
-	if (sja1105_skb_has_tag_8021q(skb)) {
-		/* Normal traffic path. */
-		sja1105_vlan_rcv(skb, &source_port, &switch_id, &vid);
-	} else if (is_link_local) {
+	if (is_link_local) {
 		/* Management traffic path. Switch embeds the switch ID and
 		 * port ID into bytes of the destination MAC, courtesy of
 		 * the incl_srcpt options.
@@ -506,14 +503,35 @@
 		sja1105_meta_unpack(skb, &meta);
 		source_port = meta.source_port;
 		switch_id = meta.switch_id;
-	} else {
+	}
+
+	/* Normal data plane traffic and link-local frames are tagged with
+	 * a tag_8021q VLAN which we have to strip
+	 */
+	if (sja1105_skb_has_tag_8021q(skb)) {
+		int tmp_source_port = -1, tmp_switch_id = -1;
+
+		sja1105_vlan_rcv(skb, &tmp_source_port, &tmp_switch_id, &vid);
+		/* Preserve the source information from the INCL_SRCPT option,
+		 * if available. This allows us to not overwrite a valid source
+		 * port and switch ID with zeroes when receiving link-local
+		 * frames from a VLAN-aware bridged port (non-zero vid).
+		 */
+		if (source_port == -1)
+			source_port = tmp_source_port;
+		if (switch_id == -1)
+			switch_id = tmp_switch_id;
+	} else if (source_port == -1 && switch_id == -1) {
+		/* Packets with no source information have no chance of
+		 * getting accepted, drop them straight away.
+		 */
 		return NULL;
 	}
 
-	if (source_port == -1 || switch_id == -1)
-		skb->dev = dsa_find_designated_bridge_port_by_vid(netdev, vid);
-	else
+	if (source_port != -1 && switch_id != -1)
 		skb->dev = dsa_master_find_slave(netdev, switch_id, source_port);
+	else
+		skb->dev = dsa_find_designated_bridge_port_by_vid(netdev, vid);
 	if (!skb->dev) {
 		netdev_warn(netdev, "Couldn't decode source port\n");
 		return NULL;
@@ -644,7 +662,8 @@
 		 * padding and trailer we need to account for the fact that
 		 * skb->data points to skb_mac_header(skb) + ETH_HLEN.
 		 */
-		pskb_trim_rcsum(skb, start_of_padding - ETH_HLEN);
+		if (pskb_trim_rcsum(skb, start_of_padding - ETH_HLEN))
+			return NULL;
 	/* Trap-to-host frame, no timestamp trailer */
 	} else {
 		*source_port = SJA1110_RX_HEADER_SRC_PORT(rx_header);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethernet/eth.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethernet/eth.c
@@ -163,17 +163,7 @@
 	eth = (struct ethhdr *)skb->data;
 	skb_pull_inline(skb, ETH_HLEN);
 
-	if (unlikely(!ether_addr_equal_64bits(eth->h_dest,
-					      dev->dev_addr))) {
-		if (unlikely(is_multicast_ether_addr_64bits(eth->h_dest))) {
-			if (ether_addr_equal_64bits(eth->h_dest, dev->broadcast))
-				skb->pkt_type = PACKET_BROADCAST;
-			else
-				skb->pkt_type = PACKET_MULTICAST;
-		} else {
-			skb->pkt_type = PACKET_OTHERHOST;
-		}
-	}
+	eth_skb_pkt_type(skb, dev);
 
 	/*
 	 * Some variants of DSA tagging don't have an ethertype field
@@ -435,11 +425,10 @@
 
 	type = eh->h_proto;
 
-	rcu_read_lock();
 	ptype = gro_find_receive_by_type(type);
 	if (ptype == NULL) {
 		flush = 1;
-		goto out_unlock;
+		goto out;
 	}
 
 	skb_gro_pull(skb, sizeof(*eh));
@@ -449,8 +438,6 @@
 					    ipv6_gro_receive, inet_gro_receive,
 					    head, skb);
 
-out_unlock:
-	rcu_read_unlock();
 out:
 	skb_gro_flush_final(skb, pp, flush);
 
@@ -468,14 +455,12 @@
 	if (skb->encapsulation)
 		skb_set_inner_mac_header(skb, nhoff);
 
-	rcu_read_lock();
 	ptype = gro_find_complete_by_type(type);
 	if (ptype != NULL)
 		err = INDIRECT_CALL_INET(ptype->callbacks.gro_complete,
 					 ipv6_gro_complete, inet_gro_complete,
 					 skb, nhoff + sizeof(*eh));
 
-	rcu_read_unlock();
 	return err;
 }
 EXPORT_SYMBOL(eth_gro_complete);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/Makefile
@@ -7,4 +7,4 @@
 ethtool_nl-y	:= netlink.o bitset.o strset.o linkinfo.o linkmodes.o \
 		   linkstate.o debug.o wol.o features.o privflags.o rings.o \
 		   channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
-		   tunnels.o fec.o eeprom.o stats.o phc_vclocks.o
+		   tunnels.o fec.o eeprom.o stats.o phc_vclocks.o mm.o
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/bitset.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/bitset.c
@@ -425,12 +425,32 @@
 	return 0;
 }
 
+/**
+ * ethnl_bitmap32_equal() - Compare two bitmaps
+ * @map1:  first bitmap
+ * @map2:  second bitmap
+ * @nbits: bit size to compare
+ *
+ * Return: true if first @nbits are equal, false if not
+ */
+static bool ethnl_bitmap32_equal(const u32 *map1, const u32 *map2,
+				 unsigned int nbits)
+{
+	if (memcmp(map1, map2, nbits / 32 * sizeof(u32)))
+		return false;
+	if (nbits % 32 == 0)
+		return true;
+	return !((map1[nbits / 32] ^ map2[nbits / 32]) &
+		 ethnl_lower_bits(nbits % 32));
+}
+
 static int
 ethnl_update_bitset32_verbose(u32 *bitmap, unsigned int nbits,
 			      const struct nlattr *attr, struct nlattr **tb,
 			      ethnl_string_array_t names,
 			      struct netlink_ext_ack *extack, bool *mod)
 {
+	u32 *saved_bitmap = NULL;
 	struct nlattr *bit_attr;
 	bool no_mask;
 	int rem;
@@ -448,8 +468,20 @@
 	}
 
 	no_mask = tb[ETHTOOL_A_BITSET_NOMASK];
-	if (no_mask)
-		ethnl_bitmap32_clear(bitmap, 0, nbits, mod);
+	if (no_mask) {
+		unsigned int nwords = DIV_ROUND_UP(nbits, 32);
+		unsigned int nbytes = nwords * sizeof(u32);
+		bool dummy;
+
+		/* The bitmap size is only the size of the map part without
+		 * its mask part.
+		 */
+		saved_bitmap = kcalloc(nwords, sizeof(u32), GFP_KERNEL);
+		if (!saved_bitmap)
+			return -ENOMEM;
+		memcpy(saved_bitmap, bitmap, nbytes);
+		ethnl_bitmap32_clear(bitmap, 0, nbits, &dummy);
+	}
 
 	nla_for_each_nested(bit_attr, tb[ETHTOOL_A_BITSET_BITS], rem) {
 		bool old_val, new_val;
@@ -458,22 +490,30 @@
 		if (nla_type(bit_attr) != ETHTOOL_A_BITSET_BITS_BIT) {
 			NL_SET_ERR_MSG_ATTR(extack, bit_attr,
 					    "only ETHTOOL_A_BITSET_BITS_BIT allowed in ETHTOOL_A_BITSET_BITS");
+			kfree(saved_bitmap);
 			return -EINVAL;
 		}
 		ret = ethnl_parse_bit(&idx, &new_val, nbits, bit_attr, no_mask,
 				      names, extack);
-		if (ret < 0)
+		if (ret < 0) {
+			kfree(saved_bitmap);
 			return ret;
+		}
 		old_val = bitmap[idx / 32] & ((u32)1 << (idx % 32));
 		if (new_val != old_val) {
 			if (new_val)
 				bitmap[idx / 32] |= ((u32)1 << (idx % 32));
 			else
 				bitmap[idx / 32] &= ~((u32)1 << (idx % 32));
-			*mod = true;
+			if (!no_mask)
+				*mod = true;
 		}
 	}
 
+	if (no_mask && !ethnl_bitmap32_equal(saved_bitmap, bitmap, nbits))
+		*mod = true;
+
+	kfree(saved_bitmap);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/cabletest.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/cabletest.c
@@ -96,7 +96,7 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev_put:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
 
@@ -353,7 +353,7 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev_put:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
  
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/channels.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/channels.c
@@ -219,6 +219,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/coalesce.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/coalesce.c
@@ -336,6 +336,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/common.h
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/common.h
@@ -52,4 +52,6 @@
 int ethtool_get_module_eeprom_call(struct net_device *dev,
 				   struct ethtool_eeprom *ee, u8 *data);
 
+bool __ethtool_dev_mm_supported(struct net_device *dev);
+
 #endif /* _ETHTOOL_COMMON_H */
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/debug.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/debug.c
@@ -123,6 +123,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/eee.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/eee.c
@@ -185,6 +185,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/eeprom.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/eeprom.c
@@ -36,7 +36,7 @@
 	if (request->page)
 		offset = request->page * ETH_MODULE_EEPROM_PAGE_LEN + offset;
 
-	if (modinfo->type == ETH_MODULE_SFF_8079 &&
+	if (modinfo->type == ETH_MODULE_SFF_8472 &&
 	    request->i2c_address == 0x51)
 		offset += ETH_MODULE_EEPROM_PAGE_LEN * 2;
 
@@ -124,7 +124,7 @@
 	if (ret)
 		goto err_free;
 
-	ret = get_module_eeprom_by_page(dev, &page_data, info->extack);
+	ret = get_module_eeprom_by_page(dev, &page_data, info ? info->extack : NULL);
 	if (ret < 0)
 		goto err_ops;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/features.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/features.c
@@ -235,17 +235,20 @@
 	dev = req_info.dev;
 
 	rtnl_lock();
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		goto out_rtnl;
 	ethnl_features_to_bitmap(old_active, dev->features);
 	ethnl_features_to_bitmap(old_wanted, dev->wanted_features);
 	ret = ethnl_parse_bitset(req_wanted, req_mask, NETDEV_FEATURE_COUNT,
 				 tb[ETHTOOL_A_FEATURES_WANTED],
 				 netdev_features_strings, info->extack);
 	if (ret < 0)
-		goto out_rtnl;
+		goto out_ops;
 	if (ethnl_bitmap_to_features(req_mask) & ~NETIF_F_ETHTOOL_BITS) {
 		GENL_SET_ERR_MSG(info, "attempt to change non-ethtool features");
 		ret = -EINVAL;
-		goto out_rtnl;
+		goto out_ops;
 	}
 
 	/* set req_wanted bits not in req_mask from old_wanted */
@@ -282,8 +285,10 @@
 	if (mod)
 		netdev_features_change(dev);
 
+out_ops:
+	ethnl_ops_complete(dev);
 out_rtnl:
 	rtnl_unlock();
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/fec.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/fec.c
@@ -305,6 +305,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/ioctl.c
@@ -433,6 +433,9 @@
 	if (!dev->ethtool_ops->get_link_ksettings)
 		return -EOPNOTSUPP;
 
+	if (!netif_device_present(dev))
+		return -ENODEV;
+
 	memset(link_ksettings, 0, sizeof(*link_ksettings));
 	return dev->ethtool_ops->get_link_ksettings(dev, link_ksettings);
 }
@@ -568,8 +571,8 @@
 static int ethtool_set_link_ksettings(struct net_device *dev,
 				      void __user *useraddr)
 {
+	struct ethtool_link_ksettings link_ksettings = {};
 	int err;
-	struct ethtool_link_ksettings link_ksettings;
 
 	ASSERT_RTNL();
 
@@ -1697,7 +1700,7 @@
 	struct ethtool_coalesce coalesce;
 	int ret;
 
-	if (!dev->ethtool_ops->set_coalesce && !dev->ethtool_ops->get_coalesce)
+	if (!dev->ethtool_ops->set_coalesce || !dev->ethtool_ops->get_coalesce)
 		return -EOPNOTSUPP;
 
 	ret = dev->ethtool_ops->get_coalesce(dev, &coalesce, &kernel_coalesce,
@@ -1988,7 +1991,8 @@
 	} else {
 		/* Driver expects to be called at twice the frequency in rc */
 		int n = rc * 2, interval = HZ / n;
-		u64 count = n * id.data, i = 0;
+		u64 count = mul_u32_u32(n, id.data);
+		u64 i = 0;
 
 		do {
 			rtnl_lock();
@@ -2073,7 +2077,8 @@
 		return n_stats;
 	if (n_stats > S32_MAX / sizeof(u64))
 		return -ENOMEM;
-	WARN_ON_ONCE(!n_stats);
+	if (WARN_ON_ONCE(!n_stats))
+		return -EOPNOTSUPP;
 
 	if (copy_from_user(&stats, useraddr, sizeof(stats)))
 		return -EFAULT;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/linkinfo.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/linkinfo.c
@@ -149,6 +149,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/linkmodes.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/linkmodes.c
@@ -277,11 +277,12 @@
 					    "lanes configuration not supported by device");
 			return -EOPNOTSUPP;
 		}
-	} else if (!lsettings->autoneg) {
-		/* If autoneg is off and lanes parameter is not passed from user,
-		 * set the lanes parameter to 0.
+	} else if (!lsettings->autoneg && ksettings->lanes) {
+		/* If autoneg is off and lanes parameter is not passed from user but
+		 * it was defined previously then set the lanes parameter to 0.
 		 */
 		ksettings->lanes = 0;
+		*mod = true;
 	}
 
 	ret = ethnl_update_bitset(ksettings->link_modes.advertising,
@@ -358,6 +359,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/linkstate.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/linkstate.c
@@ -36,6 +36,8 @@
 	mutex_lock(&phydev->lock);
 	if (!phydev->drv || !phydev->drv->get_sqi)
 		ret = -EOPNOTSUPP;
+	else if (!phydev->link)
+		ret = -ENETDOWN;
 	else
 		ret = phydev->drv->get_sqi(phydev);
 	mutex_unlock(&phydev->lock);
@@ -54,6 +56,8 @@
 	mutex_lock(&phydev->lock);
 	if (!phydev->drv || !phydev->drv->get_sqi_max)
 		ret = -EOPNOTSUPP;
+	else if (!phydev->link)
+		ret = -ENETDOWN;
 	else
 		ret = phydev->drv->get_sqi_max(phydev);
 	mutex_unlock(&phydev->lock);
@@ -61,6 +65,17 @@
 	return ret;
 };
 
+static bool linkstate_sqi_critical_error(int sqi)
+{
+	return sqi < 0 && sqi != -EOPNOTSUPP && sqi != -ENETDOWN;
+}
+
+static bool linkstate_sqi_valid(struct linkstate_reply_data *data)
+{
+	return data->sqi >= 0 && data->sqi_max >= 0 &&
+	       data->sqi <= data->sqi_max;
+}
+
 static int linkstate_get_link_ext_state(struct net_device *dev,
 					struct linkstate_reply_data *data)
 {
@@ -92,12 +107,12 @@
 	data->link = __ethtool_get_link(dev);
 
 	ret = linkstate_get_sqi(dev);
-	if (ret < 0 && ret != -EOPNOTSUPP)
+	if (linkstate_sqi_critical_error(ret))
 		goto out;
 	data->sqi = ret;
 
 	ret = linkstate_get_sqi_max(dev);
-	if (ret < 0 && ret != -EOPNOTSUPP)
+	if (linkstate_sqi_critical_error(ret))
 		goto out;
 	data->sqi_max = ret;
 
@@ -122,11 +137,10 @@
 	len = nla_total_size(sizeof(u8)) /* LINKSTATE_LINK */
 		+ 0;
 
-	if (data->sqi != -EOPNOTSUPP)
-		len += nla_total_size(sizeof(u32));
-
-	if (data->sqi_max != -EOPNOTSUPP)
-		len += nla_total_size(sizeof(u32));
+	if (linkstate_sqi_valid(data)) {
+		len += nla_total_size(sizeof(u32)); /* LINKSTATE_SQI */
+		len += nla_total_size(sizeof(u32)); /* LINKSTATE_SQI_MAX */
+	}
 
 	if (data->link_ext_state_provided)
 		len += nla_total_size(sizeof(u8)); /* LINKSTATE_EXT_STATE */
@@ -147,13 +161,14 @@
 	    nla_put_u8(skb, ETHTOOL_A_LINKSTATE_LINK, !!data->link))
 		return -EMSGSIZE;
 
-	if (data->sqi != -EOPNOTSUPP &&
-	    nla_put_u32(skb, ETHTOOL_A_LINKSTATE_SQI, data->sqi))
-		return -EMSGSIZE;
-
-	if (data->sqi_max != -EOPNOTSUPP &&
-	    nla_put_u32(skb, ETHTOOL_A_LINKSTATE_SQI_MAX, data->sqi_max))
-		return -EMSGSIZE;
+	if (linkstate_sqi_valid(data)) {
+		if (nla_put_u32(skb, ETHTOOL_A_LINKSTATE_SQI, data->sqi))
+			return -EMSGSIZE;
+
+		if (nla_put_u32(skb, ETHTOOL_A_LINKSTATE_SQI_MAX,
+				data->sqi_max))
+			return -EMSGSIZE;
+	}
 
 	if (data->link_ext_state_provided) {
 		if (nla_put_u8(skb, ETHTOOL_A_LINKSTATE_EXT_STATE,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/mm.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/mm.c
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2022-2023 NXP
+ */
+#include "common.h"
+#include "netlink.h"
+
+struct mm_req_info {
+	struct ethnl_req_info		base;
+};
+
+struct mm_reply_data {
+	struct ethnl_reply_data		base;
+	struct ethtool_mm_state		state;
+	struct ethtool_mm_stats		stats;
+};
+
+#define MM_REPDATA(__reply_base) \
+	container_of(__reply_base, struct mm_reply_data, base)
+
+#define ETHTOOL_MM_STAT_CNT \
+	(__ETHTOOL_A_MM_STAT_CNT - (ETHTOOL_A_MM_STAT_PAD + 1))
+
+const struct nla_policy ethnl_mm_get_policy[ETHTOOL_A_MM_HEADER + 1] = {
+	[ETHTOOL_A_MM_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy_stats),
+};
+
+static int mm_prepare_data(const struct ethnl_req_info *req_base,
+			   struct ethnl_reply_data *reply_base,
+			   struct genl_info *info)
+{
+	struct mm_reply_data *data = MM_REPDATA(reply_base);
+	struct net_device *dev = reply_base->dev;
+	const struct ethtool_ops *ops;
+	int ret;
+
+	ops = dev->ethtool_ops;
+
+	if (!ops->get_mm)
+		return -EOPNOTSUPP;
+
+	ethtool_stats_init((u64 *)&data->stats,
+			   sizeof(data->stats) / sizeof(u64));
+
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		return ret;
+
+	ret = ops->get_mm(dev, &data->state);
+	if (ret)
+		goto out_complete;
+
+	if (ops->get_mm_stats && (req_base->flags & ETHTOOL_FLAG_STATS))
+		ops->get_mm_stats(dev, &data->stats);
+
+out_complete:
+	ethnl_ops_complete(dev);
+
+	return ret;
+}
+
+static int mm_reply_size(const struct ethnl_req_info *req_base,
+			 const struct ethnl_reply_data *reply_base)
+{
+	int len = 0;
+
+	len += nla_total_size(sizeof(u8)); /* _MM_PMAC_ENABLED */
+	len += nla_total_size(sizeof(u8)); /* _MM_TX_ENABLED */
+	len += nla_total_size(sizeof(u8)); /* _MM_TX_ACTIVE */
+	len += nla_total_size(sizeof(u8)); /* _MM_VERIFY_ENABLED */
+	len += nla_total_size(sizeof(u8)); /* _MM_VERIFY_STATUS */
+	len += nla_total_size(sizeof(u32)); /* _MM_VERIFY_TIME */
+	len += nla_total_size(sizeof(u32)); /* _MM_MAX_VERIFY_TIME */
+	len += nla_total_size(sizeof(u32)); /* _MM_TX_MIN_FRAG_SIZE */
+	len += nla_total_size(sizeof(u32)); /* _MM_RX_MIN_FRAG_SIZE */
+
+	if (req_base->flags & ETHTOOL_FLAG_STATS)
+		len += nla_total_size(0) + /* _MM_STATS */
+		       nla_total_size_64bit(sizeof(u64)) * ETHTOOL_MM_STAT_CNT;
+
+	return len;
+}
+
+static int mm_put_stat(struct sk_buff *skb, u64 val, u16 attrtype)
+{
+	if (val == ETHTOOL_STAT_NOT_SET)
+		return 0;
+	if (nla_put_u64_64bit(skb, attrtype, val, ETHTOOL_A_MM_STAT_PAD))
+		return -EMSGSIZE;
+	return 0;
+}
+
+static int mm_put_stats(struct sk_buff *skb,
+			const struct ethtool_mm_stats *stats)
+{
+	struct nlattr *nest;
+
+	nest = nla_nest_start(skb, ETHTOOL_A_MM_STATS);
+	if (!nest)
+		return -EMSGSIZE;
+
+	if (mm_put_stat(skb, stats->MACMergeFrameAssErrorCount,
+			ETHTOOL_A_MM_STAT_REASSEMBLY_ERRORS) ||
+	    mm_put_stat(skb, stats->MACMergeFrameSmdErrorCount,
+			ETHTOOL_A_MM_STAT_SMD_ERRORS) ||
+	    mm_put_stat(skb, stats->MACMergeFrameAssOkCount,
+			ETHTOOL_A_MM_STAT_REASSEMBLY_OK) ||
+	    mm_put_stat(skb, stats->MACMergeFragCountRx,
+			ETHTOOL_A_MM_STAT_RX_FRAG_COUNT) ||
+	    mm_put_stat(skb, stats->MACMergeFragCountTx,
+			ETHTOOL_A_MM_STAT_TX_FRAG_COUNT) ||
+	    mm_put_stat(skb, stats->MACMergeHoldCount,
+			ETHTOOL_A_MM_STAT_HOLD_COUNT))
+		goto err_cancel;
+
+	nla_nest_end(skb, nest);
+	return 0;
+
+err_cancel:
+	nla_nest_cancel(skb, nest);
+	return -EMSGSIZE;
+}
+
+static int mm_fill_reply(struct sk_buff *skb,
+			 const struct ethnl_req_info *req_base,
+			 const struct ethnl_reply_data *reply_base)
+{
+	const struct mm_reply_data *data = MM_REPDATA(reply_base);
+	const struct ethtool_mm_state *state = &data->state;
+
+	if (nla_put_u8(skb, ETHTOOL_A_MM_TX_ENABLED, state->tx_enabled) ||
+	    nla_put_u8(skb, ETHTOOL_A_MM_TX_ACTIVE, state->tx_active) ||
+	    nla_put_u8(skb, ETHTOOL_A_MM_PMAC_ENABLED, state->pmac_enabled) ||
+	    nla_put_u8(skb, ETHTOOL_A_MM_VERIFY_ENABLED, state->verify_enabled) ||
+	    nla_put_u8(skb, ETHTOOL_A_MM_VERIFY_STATUS, state->verify_status) ||
+	    nla_put_u32(skb, ETHTOOL_A_MM_VERIFY_TIME, state->verify_time) ||
+	    nla_put_u32(skb, ETHTOOL_A_MM_MAX_VERIFY_TIME, state->max_verify_time) ||
+	    nla_put_u32(skb, ETHTOOL_A_MM_TX_MIN_FRAG_SIZE, state->tx_min_frag_size) ||
+	    nla_put_u32(skb, ETHTOOL_A_MM_RX_MIN_FRAG_SIZE, state->rx_min_frag_size))
+		return -EMSGSIZE;
+
+	if (req_base->flags & ETHTOOL_FLAG_STATS &&
+	    mm_put_stats(skb, &data->stats))
+		return -EMSGSIZE;
+
+	return 0;
+}
+
+const struct ethnl_request_ops ethnl_mm_request_ops = {
+	.request_cmd		= ETHTOOL_MSG_MM_GET,
+	.reply_cmd		= ETHTOOL_MSG_MM_GET_REPLY,
+	.hdr_attr		= ETHTOOL_A_MM_HEADER,
+	.req_info_size		= sizeof(struct mm_req_info),
+	.reply_data_size	= sizeof(struct mm_reply_data),
+
+	.prepare_data		= mm_prepare_data,
+	.reply_size		= mm_reply_size,
+	.fill_reply		= mm_fill_reply,
+};
+
+const struct nla_policy ethnl_mm_set_policy[ETHTOOL_A_MM_MAX + 1] = {
+	[ETHTOOL_A_MM_HEADER]		= NLA_POLICY_NESTED(ethnl_header_policy),
+	[ETHTOOL_A_MM_VERIFY_ENABLED]	= NLA_POLICY_MAX(NLA_U8, 1),
+	[ETHTOOL_A_MM_VERIFY_TIME]	= NLA_POLICY_RANGE(NLA_U32, 1, 128),
+	[ETHTOOL_A_MM_TX_ENABLED]	= NLA_POLICY_MAX(NLA_U8, 1),
+	[ETHTOOL_A_MM_PMAC_ENABLED]	= NLA_POLICY_MAX(NLA_U8, 1),
+	[ETHTOOL_A_MM_TX_MIN_FRAG_SIZE]	= NLA_POLICY_RANGE(NLA_U32, 60, 252),
+};
+
+static void mm_state_to_cfg(const struct ethtool_mm_state *state,
+			    struct ethtool_mm_cfg *cfg)
+{
+	/* We could also compare state->verify_status against
+	 * ETHTOOL_MM_VERIFY_STATUS_DISABLED, but state->verify_enabled
+	 * is more like an administrative state which should be seen in
+	 * ETHTOOL_MSG_MM_GET replies. For example, a port with verification
+	 * disabled might be in the ETHTOOL_MM_VERIFY_STATUS_INITIAL
+	 * if it's down.
+	 */
+	cfg->verify_enabled = state->verify_enabled;
+	cfg->verify_time = state->verify_time;
+	cfg->tx_enabled = state->tx_enabled;
+	cfg->pmac_enabled = state->pmac_enabled;
+	cfg->tx_min_frag_size = state->tx_min_frag_size;
+}
+
+int ethnl_set_mm(struct sk_buff *skb, struct genl_info *info)
+{
+	struct netlink_ext_ack *extack = info->extack;
+	struct ethnl_req_info req_info = {};
+	struct ethtool_mm_state state = {};
+	struct nlattr **tb = info->attrs;
+	struct ethtool_mm_cfg cfg = {};
+	const struct ethtool_ops *ops;
+	struct net_device *dev;
+	bool mod = false;
+	int ret;
+
+	ret = ethnl_parse_header_dev_get(&req_info, tb[ETHTOOL_A_MM_HEADER],
+					 genl_info_net(info), extack, true);
+	if (ret)
+		return ret;
+
+	dev = req_info.dev;
+	ops = dev->ethtool_ops;
+
+	if (!ops->get_mm || !ops->set_mm) {
+		ret = -EOPNOTSUPP;
+		goto out_dev_put;
+	}
+
+	rtnl_lock();
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		goto out_rtnl_unlock;
+
+	ret = ops->get_mm(dev, &state);
+	if (ret)
+		goto out_complete;
+
+	mm_state_to_cfg(&state, &cfg);
+
+	ethnl_update_bool(&cfg.verify_enabled, tb[ETHTOOL_A_MM_VERIFY_ENABLED],
+			  &mod);
+	ethnl_update_u32(&cfg.verify_time, tb[ETHTOOL_A_MM_VERIFY_TIME], &mod);
+	ethnl_update_bool(&cfg.tx_enabled, tb[ETHTOOL_A_MM_TX_ENABLED], &mod);
+	ethnl_update_bool(&cfg.pmac_enabled, tb[ETHTOOL_A_MM_PMAC_ENABLED],
+			  &mod);
+	ethnl_update_u32(&cfg.tx_min_frag_size,
+			 tb[ETHTOOL_A_MM_TX_MIN_FRAG_SIZE], &mod);
+
+	if (!mod)
+		goto out_complete;
+
+	if (cfg.verify_time > state.max_verify_time) {
+		NL_SET_ERR_MSG_ATTR(extack, tb[ETHTOOL_A_MM_VERIFY_TIME],
+				    "verifyTime exceeds device maximum");
+		ret = -ERANGE;
+		goto out_complete;
+	}
+
+	ret = ops->set_mm(dev, &cfg, extack);
+	if (ret)
+		goto out_complete;
+
+	ethtool_notify(dev, ETHTOOL_MSG_MM_NTF, NULL);
+
+out_complete:
+	ethnl_ops_complete(dev);
+out_rtnl_unlock:
+	rtnl_unlock();
+out_dev_put:
+	ethnl_parse_header_dev_put(&req_info);
+	return ret;
+}
+
+/* Returns whether a given device supports the MAC merge layer
+ * (has an eMAC and a pMAC). Must be called under rtnl_lock() and
+ * ethnl_ops_begin().
+ */
+bool __ethtool_dev_mm_supported(struct net_device *dev)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	struct ethtool_mm_state state = {};
+	int ret = -EOPNOTSUPP;
+
+	if (ops && ops->get_mm)
+		ret = ops->get_mm(dev, &state);
+
+	return !ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/netlink.c
@@ -40,7 +40,8 @@
 	if (dev->dev.parent)
 		pm_runtime_get_sync(dev->dev.parent);
 
-	if (!netif_device_present(dev)) {
+	if (!netif_device_present(dev) ||
+	    dev->reg_state >= NETREG_UNREGISTERING) {
 		ret = -ENODEV;
 		goto err;
 	}
@@ -141,6 +142,7 @@
 	}
 
 	req_info->dev = dev;
+	netdev_tracker_alloc(dev, &req_info->dev_tracker, GFP_KERNEL);
 	req_info->flags = flags;
 	return 0;
 }
@@ -282,6 +284,7 @@
 	[ETHTOOL_MSG_MODULE_EEPROM_GET]	= &ethnl_module_eeprom_request_ops,
 	[ETHTOOL_MSG_STATS_GET]		= &ethnl_stats_request_ops,
 	[ETHTOOL_MSG_PHC_VCLOCKS_GET]	= &ethnl_phc_vclocks_request_ops,
+	[ETHTOOL_MSG_MM_GET]		= &ethnl_mm_request_ops,
 };
 
 static struct ethnl_dump_ctx *ethnl_dump_context(struct netlink_callback *cb)
@@ -398,7 +401,7 @@
 		ops->cleanup_data(reply_data);
 
 	genlmsg_end(rskb, reply_payload);
-	dev_put(req_info->dev);
+	dev_put_track(req_info->dev, &req_info->dev_tracker);
 	kfree(reply_data);
 	kfree(req_info);
 	return genlmsg_reply(rskb, info);
@@ -410,7 +413,7 @@
 	if (ops->cleanup_data)
 		ops->cleanup_data(reply_data);
 err_dev:
-	dev_put(req_info->dev);
+	dev_put_track(req_info->dev, &req_info->dev_tracker);
 	kfree(reply_data);
 	kfree(req_info);
 	return ret;
@@ -546,7 +549,7 @@
 		 * same parser as for non-dump (doit) requests is used, it
 		 * would take reference to the device if it finds one
 		 */
-		dev_put(req_info->dev);
+		dev_put_track(req_info->dev, &req_info->dev_tracker);
 		req_info->dev = NULL;
 	}
 	if (ret < 0)
@@ -593,6 +596,7 @@
 	[ETHTOOL_MSG_PAUSE_NTF]		= &ethnl_pause_request_ops,
 	[ETHTOOL_MSG_EEE_NTF]		= &ethnl_eee_request_ops,
 	[ETHTOOL_MSG_FEC_NTF]		= &ethnl_fec_request_ops,
+	[ETHTOOL_MSG_MM_NTF]		= &ethnl_mm_request_ops,
 };
 
 /* default notification handler */
@@ -622,6 +626,7 @@
 	}
 
 	req_info->dev = dev;
+	netdev_tracker_alloc(dev, &req_info->dev_tracker, GFP_KERNEL);
 	req_info->flags |= ETHTOOL_FLAG_COMPACT_BITSETS;
 
 	ethnl_init_reply_data(reply_data, ops, dev);
@@ -686,6 +691,7 @@
 	[ETHTOOL_MSG_PAUSE_NTF]		= ethnl_default_notify,
 	[ETHTOOL_MSG_EEE_NTF]		= ethnl_default_notify,
 	[ETHTOOL_MSG_FEC_NTF]		= ethnl_default_notify,
+	[ETHTOOL_MSG_MM_NTF]		= ethnl_default_notify,
 };
 
 void ethtool_notify(struct net_device *dev, unsigned int cmd, const void *data)
@@ -999,6 +1005,22 @@
 		.policy = ethnl_phc_vclocks_get_policy,
 		.maxattr = ARRAY_SIZE(ethnl_phc_vclocks_get_policy) - 1,
 	},
+	{
+		.cmd	= ETHTOOL_MSG_MM_GET,
+		.doit	= ethnl_default_doit,
+		.start	= ethnl_default_start,
+		.dumpit	= ethnl_default_dumpit,
+		.done	= ethnl_default_done,
+		.policy = ethnl_mm_get_policy,
+		.maxattr = ARRAY_SIZE(ethnl_mm_get_policy) - 1,
+	},
+	{
+		.cmd	= ETHTOOL_MSG_MM_SET,
+		.flags	= GENL_UNS_ADMIN_PERM,
+		.doit	= ethnl_set_mm,
+		.policy = ethnl_mm_set_policy,
+		.maxattr = ARRAY_SIZE(ethnl_mm_set_policy) - 1,
+	},
 };
 
 static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/netlink.h
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/netlink.h
@@ -112,6 +112,32 @@
 }
 
 /**
+ * ethnl_update_bool() - update bool from NLA_U8 attribute
+ * @dst:  value to update
+ * @attr: netlink attribute with new value or null
+ * @mod:  pointer to bool for modification tracking
+ *
+ * Use the u8 value from NLA_U8 netlink attribute @attr to set bool variable
+ * pointed to by @dst to false (if zero) or 1 (if not); do nothing if @attr is
+ * null. Bool pointed to by @mod is set to true if this function changed the
+ * logical value of *dst, otherwise it is left as is.
+ */
+static inline void ethnl_update_bool(bool *dst, const struct nlattr *attr,
+				     bool *mod)
+{
+	u8 val;
+
+	if (!attr)
+		return;
+	val = !!nla_get_u8(attr);
+	if (*dst == val)
+		return;
+
+	*dst = val;
+	*mod = true;
+}
+
+/**
  * ethnl_update_bool32() - update u32 used as bool from NLA_U8 attribute
  * @dst:  value to update
  * @attr: netlink attribute with new value or null
@@ -222,6 +248,7 @@
 /**
  * struct ethnl_req_info - base type of request information for GET requests
  * @dev:   network device the request is for (may be null)
+ * @dev_tracker: refcount tracker for @dev reference
  * @flags: request flags common for all request types
  *
  * This is a common base for request specific structures holding data from
@@ -230,9 +257,15 @@
  */
 struct ethnl_req_info {
 	struct net_device	*dev;
+	netdevice_tracker	dev_tracker;
 	u32			flags;
 };
 
+static inline void ethnl_parse_header_dev_put(struct ethnl_req_info *req_info)
+{
+	dev_put_track(req_info->dev, &req_info->dev_tracker);
+}
+
 /**
  * struct ethnl_reply_data - base type of reply data for GET requests
  * @dev:       device for current reply message; in single shot requests it is
@@ -337,6 +370,7 @@
 extern const struct ethnl_request_ops ethnl_module_eeprom_request_ops;
 extern const struct ethnl_request_ops ethnl_stats_request_ops;
 extern const struct ethnl_request_ops ethnl_phc_vclocks_request_ops;
+extern const struct ethnl_request_ops ethnl_mm_request_ops;
 
 extern const struct nla_policy ethnl_header_policy[ETHTOOL_A_HEADER_FLAGS + 1];
 extern const struct nla_policy ethnl_header_policy_stats[ETHTOOL_A_HEADER_FLAGS + 1];
@@ -360,7 +394,7 @@
 extern const struct nla_policy ethnl_channels_set_policy[ETHTOOL_A_CHANNELS_COMBINED_COUNT + 1];
 extern const struct nla_policy ethnl_coalesce_get_policy[ETHTOOL_A_COALESCE_HEADER + 1];
 extern const struct nla_policy ethnl_coalesce_set_policy[ETHTOOL_A_COALESCE_MAX + 1];
-extern const struct nla_policy ethnl_pause_get_policy[ETHTOOL_A_PAUSE_HEADER + 1];
+extern const struct nla_policy ethnl_pause_get_policy[ETHTOOL_A_PAUSE_STATS_SRC + 1];
 extern const struct nla_policy ethnl_pause_set_policy[ETHTOOL_A_PAUSE_TX + 1];
 extern const struct nla_policy ethnl_eee_get_policy[ETHTOOL_A_EEE_HEADER + 1];
 extern const struct nla_policy ethnl_eee_set_policy[ETHTOOL_A_EEE_TX_LPI_TIMER + 1];
@@ -371,8 +405,10 @@
 extern const struct nla_policy ethnl_fec_get_policy[ETHTOOL_A_FEC_HEADER + 1];
 extern const struct nla_policy ethnl_fec_set_policy[ETHTOOL_A_FEC_AUTO + 1];
 extern const struct nla_policy ethnl_module_eeprom_get_policy[ETHTOOL_A_MODULE_EEPROM_I2C_ADDRESS + 1];
-extern const struct nla_policy ethnl_stats_get_policy[ETHTOOL_A_STATS_GROUPS + 1];
+extern const struct nla_policy ethnl_stats_get_policy[ETHTOOL_A_STATS_SRC + 1];
 extern const struct nla_policy ethnl_phc_vclocks_get_policy[ETHTOOL_A_PHC_VCLOCKS_HEADER + 1];
+extern const struct nla_policy ethnl_mm_get_policy[ETHTOOL_A_MM_HEADER + 1];
+extern const struct nla_policy ethnl_mm_set_policy[ETHTOOL_A_MM_MAX + 1];
 
 int ethnl_set_linkinfo(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_linkmodes(struct sk_buff *skb, struct genl_info *info);
@@ -391,6 +427,7 @@
 int ethnl_tunnel_info_start(struct netlink_callback *cb);
 int ethnl_tunnel_info_dumpit(struct sk_buff *skb, struct netlink_callback *cb);
 int ethnl_set_fec(struct sk_buff *skb, struct genl_info *info);
+int ethnl_set_mm(struct sk_buff *skb, struct genl_info *info);
 
 extern const char stats_std_names[__ETHTOOL_STATS_CNT][ETH_GSTRING_LEN];
 extern const char stats_eth_phy_names[__ETHTOOL_A_STATS_ETH_PHY_CNT][ETH_GSTRING_LEN];
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/pause.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/pause.c
@@ -5,8 +5,12 @@
 
 struct pause_req_info {
 	struct ethnl_req_info		base;
+	enum ethtool_mac_stats_src	src;
 };
 
+#define PAUSE_REQINFO(__req_base) \
+	container_of(__req_base, struct pause_req_info, base)
+
 struct pause_reply_data {
 	struct ethnl_reply_data		base;
 	struct ethtool_pauseparam	pauseparam;
@@ -19,13 +23,40 @@
 const struct nla_policy ethnl_pause_get_policy[] = {
 	[ETHTOOL_A_PAUSE_HEADER]		=
 		NLA_POLICY_NESTED(ethnl_header_policy_stats),
+	[ETHTOOL_A_PAUSE_STATS_SRC]		=
+		NLA_POLICY_MAX(NLA_U32, ETHTOOL_MAC_STATS_SRC_PMAC),
 };
 
+static int pause_parse_request(struct ethnl_req_info *req_base,
+			       struct nlattr **tb,
+			       struct netlink_ext_ack *extack)
+{
+	enum ethtool_mac_stats_src src = ETHTOOL_MAC_STATS_SRC_AGGREGATE;
+	struct pause_req_info *req_info = PAUSE_REQINFO(req_base);
+
+	if (tb[ETHTOOL_A_PAUSE_STATS_SRC]) {
+		if (!(req_base->flags & ETHTOOL_FLAG_STATS)) {
+			NL_SET_ERR_MSG_MOD(extack,
+					   "ETHTOOL_FLAG_STATS must be set when requesting a source of stats");
+			return -EINVAL;
+		}
+
+		src = nla_get_u32(tb[ETHTOOL_A_PAUSE_STATS_SRC]);
+	}
+
+	req_info->src = src;
+
+	return 0;
+}
+
 static int pause_prepare_data(const struct ethnl_req_info *req_base,
 			      struct ethnl_reply_data *reply_base,
 			      struct genl_info *info)
 {
+	const struct pause_req_info *req_info = PAUSE_REQINFO(req_base);
+	struct netlink_ext_ack *extack = info ? info->extack : NULL;
 	struct pause_reply_data *data = PAUSE_REPDATA(reply_base);
+	enum ethtool_mac_stats_src src = req_info->src;
 	struct net_device *dev = reply_base->dev;
 	int ret;
 
@@ -34,14 +65,26 @@
 
 	ethtool_stats_init((u64 *)&data->pausestat,
 			   sizeof(data->pausestat) / 8);
+	data->pausestat.src = src;
 
 	ret = ethnl_ops_begin(dev);
 	if (ret < 0)
 		return ret;
+
+	if ((src == ETHTOOL_MAC_STATS_SRC_EMAC ||
+	     src == ETHTOOL_MAC_STATS_SRC_PMAC) &&
+	    !__ethtool_dev_mm_supported(dev)) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Device does not support MAC merge layer");
+		ethnl_ops_complete(dev);
+		return -EOPNOTSUPP;
+	}
+
 	dev->ethtool_ops->get_pauseparam(dev, &data->pauseparam);
 	if (req_base->flags & ETHTOOL_FLAG_STATS &&
 	    dev->ethtool_ops->get_pause_stats)
 		dev->ethtool_ops->get_pause_stats(dev, &data->pausestat);
+
 	ethnl_ops_complete(dev);
 
 	return 0;
@@ -56,8 +99,8 @@
 
 	if (req_base->flags & ETHTOOL_FLAG_STATS)
 		n += nla_total_size(0) +	/* _PAUSE_STATS */
-			nla_total_size_64bit(sizeof(u64)) *
-				(ETHTOOL_A_PAUSE_STAT_MAX - 2);
+		     nla_total_size(sizeof(u32)) + /* _PAUSE_STATS_SRC */
+		     nla_total_size_64bit(sizeof(u64)) * ETHTOOL_PAUSE_STAT_CNT;
 	return n;
 }
 
@@ -78,6 +121,9 @@
 	const u16 pad = ETHTOOL_A_PAUSE_STAT_PAD;
 	struct nlattr *nest;
 
+	if (nla_put_u32(skb, ETHTOOL_A_PAUSE_STATS_SRC, pause_stats->src))
+		return -EMSGSIZE;
+
 	nest = nla_nest_start(skb, ETHTOOL_A_PAUSE_STATS);
 	if (!nest)
 		return -EMSGSIZE;
@@ -122,6 +168,7 @@
 	.req_info_size		= sizeof(struct pause_req_info),
 	.reply_data_size	= sizeof(struct pause_reply_data),
 
+	.parse_request		= pause_parse_request,
 	.prepare_data		= pause_prepare_data,
 	.reply_size		= pause_reply_size,
 	.fill_reply		= pause_fill_reply,
@@ -182,6 +229,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/privflags.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/privflags.c
@@ -196,6 +196,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/rings.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/rings.c
@@ -174,6 +174,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/stats.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/stats.c
@@ -7,6 +7,7 @@
 struct stats_req_info {
 	struct ethnl_req_info		base;
 	DECLARE_BITMAP(stat_mask, __ETHTOOL_STATS_CNT);
+	enum ethtool_mac_stats_src	src;
 };
 
 #define STATS_REQINFO(__req_base) \
@@ -73,16 +74,19 @@
 	[ETHTOOL_A_STATS_RMON_JABBER]		= "etherStatsJabbers",
 };
 
-const struct nla_policy ethnl_stats_get_policy[ETHTOOL_A_STATS_GROUPS + 1] = {
+const struct nla_policy ethnl_stats_get_policy[ETHTOOL_A_STATS_SRC + 1] = {
 	[ETHTOOL_A_STATS_HEADER]	=
 		NLA_POLICY_NESTED(ethnl_header_policy),
 	[ETHTOOL_A_STATS_GROUPS]	= { .type = NLA_NESTED },
+	[ETHTOOL_A_STATS_SRC]		=
+		NLA_POLICY_MAX(NLA_U32, ETHTOOL_MAC_STATS_SRC_PMAC),
 };
 
 static int stats_parse_request(struct ethnl_req_info *req_base,
 			       struct nlattr **tb,
 			       struct netlink_ext_ack *extack)
 {
+	enum ethtool_mac_stats_src src = ETHTOOL_MAC_STATS_SRC_AGGREGATE;
 	struct stats_req_info *req_info = STATS_REQINFO(req_base);
 	bool mod = false;
 	int err;
@@ -98,6 +102,11 @@
 		return -EINVAL;
 	}
 
+	if (tb[ETHTOOL_A_STATS_SRC])
+		src = nla_get_u32(tb[ETHTOOL_A_STATS_SRC]);
+
+	req_info->src = src;
+
 	return 0;
 }
 
@@ -106,7 +115,9 @@
 			      struct genl_info *info)
 {
 	const struct stats_req_info *req_info = STATS_REQINFO(req_base);
+	struct netlink_ext_ack *extack = info ? info->extack : NULL;
 	struct stats_reply_data *data = STATS_REPDATA(reply_base);
+	enum ethtool_mac_stats_src src = req_info->src;
 	struct net_device *dev = reply_base->dev;
 	int ret;
 
@@ -114,6 +125,15 @@
 	if (ret < 0)
 		return ret;
 
+	if ((src == ETHTOOL_MAC_STATS_SRC_EMAC ||
+	     src == ETHTOOL_MAC_STATS_SRC_PMAC) &&
+	    !__ethtool_dev_mm_supported(dev)) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Device does not support MAC merge layer");
+		ethnl_ops_complete(dev);
+		return -EOPNOTSUPP;
+	}
+
 	/* Mark all stats as unset (see ETHTOOL_STAT_NOT_SET) to prevent them
 	 * from being reported to user space in case driver did not set them.
 	 */
@@ -122,6 +142,11 @@
 	memset(&data->ctrl_stats, 0xff, sizeof(data->ctrl_stats));
 	memset(&data->rmon_stats, 0xff, sizeof(data->rmon_stats));
 
+	data->phy_stats.src = src;
+	data->mac_stats.src = src;
+	data->ctrl_stats.src = src;
+	data->rmon_stats.src = src;
+
 	if (test_bit(ETHTOOL_STATS_ETH_PHY, req_info->stat_mask) &&
 	    dev->ethtool_ops->get_eth_phy_stats)
 		dev->ethtool_ops->get_eth_phy_stats(dev, &data->phy_stats);
@@ -147,6 +172,8 @@
 	unsigned int n_grps = 0, n_stats = 0;
 	int len = 0;
 
+	len += nla_total_size(sizeof(u32)); /* _STATS_SRC */
+
 	if (test_bit(ETHTOOL_STATS_ETH_PHY, req_info->stat_mask)) {
 		n_stats += sizeof(struct ethtool_eth_phy_stats) / sizeof(u64);
 		n_grps++;
@@ -380,6 +407,9 @@
 	const struct stats_reply_data *data = STATS_REPDATA(reply_base);
 	int ret = 0;
 
+	if (nla_put_u32(skb, ETHTOOL_A_STATS_SRC, req_info->src))
+		return -EMSGSIZE;
+
 	if (!ret && test_bit(ETHTOOL_STATS_ETH_PHY, req_info->stat_mask))
 		ret = stats_put_stats(skb, data, ETHTOOL_STATS_ETH_PHY,
 				      ETH_SS_STATS_ETH_PHY,
@@ -411,3 +441,130 @@
 	.reply_size		= stats_reply_size,
 	.fill_reply		= stats_fill_reply,
 };
+
+static u64 ethtool_stats_sum(u64 a, u64 b)
+{
+	if (a == ETHTOOL_STAT_NOT_SET)
+		return b;
+	if (b == ETHTOOL_STAT_NOT_SET)
+		return a;
+	return a + b;
+}
+
+/* Avoid modifying the aggregation procedure every time a new counter is added
+ * by treating the structures as an array of u64 statistics.
+ */
+static void ethtool_aggregate_stats(void *aggr_stats, const void *emac_stats,
+				    const void *pmac_stats, size_t stats_size,
+				    size_t stats_offset)
+{
+	size_t num_stats = stats_size / sizeof(u64);
+	const u64 *s1 = emac_stats + stats_offset;
+	const u64 *s2 = pmac_stats + stats_offset;
+	u64 *s = aggr_stats + stats_offset;
+	int i;
+
+	for (i = 0; i < num_stats; i++)
+		s[i] = ethtool_stats_sum(s1[i], s2[i]);
+}
+
+void ethtool_aggregate_mac_stats(struct net_device *dev,
+				 struct ethtool_eth_mac_stats *mac_stats)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	struct ethtool_eth_mac_stats pmac, emac;
+
+	memset(&emac, 0xff, sizeof(emac));
+	memset(&pmac, 0xff, sizeof(pmac));
+	emac.src = ETHTOOL_MAC_STATS_SRC_EMAC;
+	pmac.src = ETHTOOL_MAC_STATS_SRC_PMAC;
+
+	ops->get_eth_mac_stats(dev, &emac);
+	ops->get_eth_mac_stats(dev, &pmac);
+
+	ethtool_aggregate_stats(mac_stats, &emac, &pmac,
+				sizeof(mac_stats->stats),
+				offsetof(struct ethtool_eth_mac_stats, stats));
+}
+EXPORT_SYMBOL(ethtool_aggregate_mac_stats);
+
+void ethtool_aggregate_phy_stats(struct net_device *dev,
+				 struct ethtool_eth_phy_stats *phy_stats)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	struct ethtool_eth_phy_stats pmac, emac;
+
+	memset(&emac, 0xff, sizeof(emac));
+	memset(&pmac, 0xff, sizeof(pmac));
+	emac.src = ETHTOOL_MAC_STATS_SRC_EMAC;
+	pmac.src = ETHTOOL_MAC_STATS_SRC_PMAC;
+
+	ops->get_eth_phy_stats(dev, &emac);
+	ops->get_eth_phy_stats(dev, &pmac);
+
+	ethtool_aggregate_stats(phy_stats, &emac, &pmac,
+				sizeof(phy_stats->stats),
+				offsetof(struct ethtool_eth_phy_stats, stats));
+}
+EXPORT_SYMBOL(ethtool_aggregate_phy_stats);
+
+void ethtool_aggregate_ctrl_stats(struct net_device *dev,
+				  struct ethtool_eth_ctrl_stats *ctrl_stats)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	struct ethtool_eth_ctrl_stats pmac, emac;
+
+	memset(&emac, 0xff, sizeof(emac));
+	memset(&pmac, 0xff, sizeof(pmac));
+	emac.src = ETHTOOL_MAC_STATS_SRC_EMAC;
+	pmac.src = ETHTOOL_MAC_STATS_SRC_PMAC;
+
+	ops->get_eth_ctrl_stats(dev, &emac);
+	ops->get_eth_ctrl_stats(dev, &pmac);
+
+	ethtool_aggregate_stats(ctrl_stats, &emac, &pmac,
+				sizeof(ctrl_stats->stats),
+				offsetof(struct ethtool_eth_ctrl_stats, stats));
+}
+EXPORT_SYMBOL(ethtool_aggregate_ctrl_stats);
+
+void ethtool_aggregate_pause_stats(struct net_device *dev,
+				   struct ethtool_pause_stats *pause_stats)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	struct ethtool_pause_stats pmac, emac;
+
+	memset(&emac, 0xff, sizeof(emac));
+	memset(&pmac, 0xff, sizeof(pmac));
+	emac.src = ETHTOOL_MAC_STATS_SRC_EMAC;
+	pmac.src = ETHTOOL_MAC_STATS_SRC_PMAC;
+
+	ops->get_pause_stats(dev, &emac);
+	ops->get_pause_stats(dev, &pmac);
+
+	ethtool_aggregate_stats(pause_stats, &emac, &pmac,
+				sizeof(pause_stats->stats),
+				offsetof(struct ethtool_pause_stats, stats));
+}
+EXPORT_SYMBOL(ethtool_aggregate_pause_stats);
+
+void ethtool_aggregate_rmon_stats(struct net_device *dev,
+				  struct ethtool_rmon_stats *rmon_stats)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	const struct ethtool_rmon_hist_range *dummy;
+	struct ethtool_rmon_stats pmac, emac;
+
+	memset(&emac, 0xff, sizeof(emac));
+	memset(&pmac, 0xff, sizeof(pmac));
+	emac.src = ETHTOOL_MAC_STATS_SRC_EMAC;
+	pmac.src = ETHTOOL_MAC_STATS_SRC_PMAC;
+
+	ops->get_rmon_stats(dev, &emac, &dummy);
+	ops->get_rmon_stats(dev, &pmac, &dummy);
+
+	ethtool_aggregate_stats(rmon_stats, &emac, &pmac,
+				sizeof(rmon_stats->stats),
+				offsetof(struct ethtool_rmon_stats, stats));
+}
+EXPORT_SYMBOL(ethtool_aggregate_rmon_stats);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/tunnels.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/tunnels.c
@@ -195,7 +195,7 @@
 	if (ret)
 		goto err_free_msg;
 	rtnl_unlock();
-	dev_put(req_info.dev);
+	ethnl_parse_header_dev_put(&req_info);
 	genlmsg_end(rskb, reply_payload);
 
 	return genlmsg_reply(rskb, info);
@@ -204,7 +204,7 @@
 	nlmsg_free(rskb);
 err_unlock_rtnl:
 	rtnl_unlock();
-	dev_put(req_info.dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
 
@@ -230,7 +230,7 @@
 					 sock_net(cb->skb->sk), cb->extack,
 					 false);
 	if (ctx->req_info.dev) {
-		dev_put(ctx->req_info.dev);
+		ethnl_parse_header_dev_put(&ctx->req_info);
 		ctx->req_info.dev = NULL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ethtool/wol.c
+++ linux-xilinx-zynqmp-5.15.0/net/ethtool/wol.c
@@ -165,6 +165,6 @@
 out_rtnl:
 	rtnl_unlock();
 out_dev:
-	dev_put(dev);
+	ethnl_parse_header_dev_put(&req_info);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/hsr/hsr_device.c
+++ linux-xilinx-zynqmp-5.15.0/net/hsr/hsr_device.c
@@ -30,13 +30,13 @@
 
 static void __hsr_set_operstate(struct net_device *dev, int transition)
 {
-	write_lock_bh(&dev_base_lock);
+	write_lock(&dev_base_lock);
 	if (dev->operstate != transition) {
 		dev->operstate = transition;
-		write_unlock_bh(&dev_base_lock);
+		write_unlock(&dev_base_lock);
 		netdev_state_change(dev);
 	} else {
-		write_unlock_bh(&dev_base_lock);
+		write_unlock(&dev_base_lock);
 	}
 }
 
@@ -219,7 +219,9 @@
 		skb->dev = master->dev;
 		skb_reset_mac_header(skb);
 		skb_reset_mac_len(skb);
+		spin_lock_bh(&hsr->seqnr_lock);
 		hsr_forward_skb(skb, master);
+		spin_unlock_bh(&hsr->seqnr_lock);
 	} else {
 		atomic_long_inc(&dev->tx_dropped);
 		dev_kfree_skb_any(skb);
@@ -254,6 +256,8 @@
 	skb->dev = master->dev;
 	skb->priority = TC_PRIO_CONTROL;
 
+	skb_reset_network_header(skb);
+	skb_reset_transport_header(skb);
 	if (dev_hard_header(skb, skb->dev, ETH_P_PRP,
 			    hsr->sup_multicast_addr,
 			    skb->dev->dev_addr, skb->len) <= 0)
@@ -261,8 +265,6 @@
 
 	skb_reset_mac_header(skb);
 	skb_reset_mac_len(skb);
-	skb_reset_network_header(skb);
-	skb_reset_transport_header(skb);
 
 	return skb;
 out:
@@ -278,7 +280,6 @@
 	__u8 type = HSR_TLV_LIFE_CHECK;
 	struct hsr_sup_payload *hsr_sp;
 	struct hsr_sup_tag *hsr_stag;
-	unsigned long irqflags;
 	struct sk_buff *skb;
 
 	*interval = msecs_to_jiffies(HSR_LIFE_CHECK_INTERVAL);
@@ -290,7 +291,7 @@
 
 	skb = hsr_init_skb(master);
 	if (!skb) {
-		WARN_ONCE(1, "HSR: Could not send supervision frame\n");
+		netdev_warn_once(master->dev, "HSR: Could not send supervision frame\n");
 		return;
 	}
 
@@ -299,7 +300,7 @@
 	set_hsr_stag_HSR_ver(hsr_stag, hsr->prot_version);
 
 	/* From HSRv1 on we have separate supervision sequence numbers. */
-	spin_lock_irqsave(&master->hsr->seqnr_lock, irqflags);
+	spin_lock_bh(&hsr->seqnr_lock);
 	if (hsr->prot_version > 0) {
 		hsr_stag->sequence_nr = htons(hsr->sup_sequence_nr);
 		hsr->sup_sequence_nr++;
@@ -307,7 +308,6 @@
 		hsr_stag->sequence_nr = htons(hsr->sequence_nr);
 		hsr->sequence_nr++;
 	}
-	spin_unlock_irqrestore(&master->hsr->seqnr_lock, irqflags);
 
 	hsr_stag->HSR_TLV_type = type;
 	/* TODO: Why 12 in HSRv0? */
@@ -318,11 +318,13 @@
 	hsr_sp = skb_put(skb, sizeof(struct hsr_sup_payload));
 	ether_addr_copy(hsr_sp->macaddress_A, master->dev->dev_addr);
 
-	if (skb_put_padto(skb, ETH_ZLEN))
+	if (skb_put_padto(skb, ETH_ZLEN)) {
+		spin_unlock_bh(&hsr->seqnr_lock);
 		return;
+	}
 
 	hsr_forward_skb(skb, master);
-
+	spin_unlock_bh(&hsr->seqnr_lock);
 	return;
 }
 
@@ -332,12 +334,11 @@
 	struct hsr_priv *hsr = master->hsr;
 	struct hsr_sup_payload *hsr_sp;
 	struct hsr_sup_tag *hsr_stag;
-	unsigned long irqflags;
 	struct sk_buff *skb;
 
 	skb = hsr_init_skb(master);
 	if (!skb) {
-		WARN_ONCE(1, "PRP: Could not send supervision frame\n");
+		netdev_warn_once(master->dev, "PRP: Could not send supervision frame\n");
 		return;
 	}
 
@@ -347,7 +348,7 @@
 	set_hsr_stag_HSR_ver(hsr_stag, (hsr->prot_version ? 1 : 0));
 
 	/* From HSRv1 on we have separate supervision sequence numbers. */
-	spin_lock_irqsave(&master->hsr->seqnr_lock, irqflags);
+	spin_lock_bh(&hsr->seqnr_lock);
 	hsr_stag->sequence_nr = htons(hsr->sup_sequence_nr);
 	hsr->sup_sequence_nr++;
 	hsr_stag->HSR_TLV_type = PRP_TLV_LIFE_CHECK_DD;
@@ -358,13 +359,12 @@
 	ether_addr_copy(hsr_sp->macaddress_A, master->dev->dev_addr);
 
 	if (skb_put_padto(skb, ETH_ZLEN)) {
-		spin_unlock_irqrestore(&master->hsr->seqnr_lock, irqflags);
+		spin_unlock_bh(&hsr->seqnr_lock);
 		return;
 	}
 
-	spin_unlock_irqrestore(&master->hsr->seqnr_lock, irqflags);
-
 	hsr_forward_skb(skb, master);
+	spin_unlock_bh(&hsr->seqnr_lock);
 }
 
 /* Announce (supervision frame) timer function
@@ -444,7 +444,7 @@
 	dev->header_ops = &hsr_header_ops;
 	dev->netdev_ops = &hsr_device_ops;
 	SET_NETDEV_DEVTYPE(dev, &hsr_type);
-	dev->priv_flags |= IFF_NO_QUEUE;
+	dev->priv_flags |= IFF_NO_QUEUE | IFF_DISABLE_NETPOLL;
 
 	dev->needs_free_netdev = true;
 
@@ -493,7 +493,7 @@
 	INIT_LIST_HEAD(&hsr->self_node_db);
 	spin_lock_init(&hsr->list_lock);
 
-	ether_addr_copy(hsr_dev->dev_addr, slave[0]->dev_addr);
+	eth_hw_addr_set(hsr_dev, slave[0]->dev_addr);
 
 	/* initialize protocol specific functions */
 	if (protocol_version == PRP_V1) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/hsr/hsr_forward.c
+++ linux-xilinx-zynqmp-5.15.0/net/hsr/hsr_forward.c
@@ -108,15 +108,15 @@
 				       struct hsr_port *port)
 {
 	if (!frame->skb_std) {
-		if (frame->skb_hsr) {
+		if (frame->skb_hsr)
 			frame->skb_std =
 				create_stripped_skb_hsr(frame->skb_hsr, frame);
-		} else {
-			/* Unexpected */
-			WARN_ONCE(1, "%s:%d: Unexpected frame received (port_src %s)\n",
-				  __FILE__, __LINE__, port->dev->name);
+		else
+			netdev_warn_once(port->dev,
+					 "Unexpected frame received in hsr_get_untagged_frame()\n");
+
+		if (!frame->skb_std)
 			return NULL;
-		}
 	}
 
 	return skb_clone(frame->skb_std, GFP_ATOMIC);
@@ -300,26 +300,25 @@
 	skb = skb_copy_expand(frame->skb_std, 0,
 			      skb_tailroom(frame->skb_std) + HSR_HLEN,
 			      GFP_ATOMIC);
-	prp_fill_rct(skb, frame, port);
-
-	return skb;
+	return prp_fill_rct(skb, frame, port);
 }
 
 static void hsr_deliver_master(struct sk_buff *skb, struct net_device *dev,
 			       struct hsr_node *node_src)
 {
 	bool was_multicast_frame;
-	int res;
+	int res, recv_len;
 
 	was_multicast_frame = (skb->pkt_type == PACKET_MULTICAST);
 	hsr_addr_subst_source(node_src, skb);
 	skb_pull(skb, ETH_HLEN);
+	recv_len = skb->len;
 	res = netif_rx(skb);
 	if (res == NET_RX_DROP) {
 		dev->stats.rx_dropped++;
 	} else {
 		dev->stats.rx_packets++;
-		dev->stats.rx_bytes += skb->len;
+		dev->stats.rx_bytes += recv_len;
 		if (was_multicast_frame)
 			dev->stats.multicast++;
 	}
@@ -457,7 +456,6 @@
 {
 	struct hsr_port *port = frame->port_rcv;
 	struct hsr_priv *hsr = port->hsr;
-	unsigned long irqflags;
 
 	frame->skb_hsr = NULL;
 	frame->skb_prp = NULL;
@@ -467,10 +465,9 @@
 		frame->is_from_san = true;
 	} else {
 		/* Sequence nr for the master node */
-		spin_lock_irqsave(&hsr->seqnr_lock, irqflags);
+		lockdep_assert_held(&hsr->seqnr_lock);
 		frame->sequence_nr = hsr->sequence_nr;
 		hsr->sequence_nr++;
-		spin_unlock_irqrestore(&hsr->seqnr_lock, irqflags);
 	}
 }
 
@@ -549,10 +546,16 @@
 		frame->is_vlan = true;
 
 	if (frame->is_vlan) {
-		vlan_hdr = (struct hsr_vlan_ethhdr *)ethhdr;
+		/* Note: skb->mac_len might be wrong here. */
+		if (!pskb_may_pull(skb,
+				   skb_mac_offset(skb) +
+				   offsetofend(struct hsr_vlan_ethhdr, vlanhdr)))
+			return -EINVAL;
+		vlan_hdr = (struct hsr_vlan_ethhdr *)skb_mac_header(skb);
 		proto = vlan_hdr->vlanhdr.h_vlan_encapsulated_proto;
 		/* FIXME: */
 		netdev_warn_once(skb->dev, "VLAN not yet supported");
+		return -EINVAL;
 	}
 
 	frame->is_from_san = false;
@@ -571,11 +574,13 @@
 {
 	struct hsr_frame_info frame;
 
+	rcu_read_lock();
 	if (fill_frame_info(&frame, skb, port) < 0)
 		goto out_drop;
 
 	hsr_register_frame_in(frame.node_src, port, frame.sequence_nr);
 	hsr_forward_do(&frame);
+	rcu_read_unlock();
 	/* Gets called for ingress frames as well as egress from master port.
 	 * So check and increment stats for master port only here.
 	 */
@@ -590,6 +595,7 @@
 	return;
 
 out_drop:
+	rcu_read_unlock();
 	port->dev->stats.tx_dropped++;
 	kfree_skb(skb);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/hsr/hsr_framereg.c
+++ linux-xilinx-zynqmp-5.15.0/net/hsr/hsr_framereg.c
@@ -159,6 +159,7 @@
 		return NULL;
 
 	ether_addr_copy(new_node->macaddress_A, addr);
+	spin_lock_init(&new_node->seq_out_lock);
 
 	/* We are only interested in time diffs here, so use current jiffies
 	 * as initialization. (0 could trigger an spurious ring error warning).
@@ -236,6 +237,10 @@
 	 */
 	if (ethhdr->h_proto == htons(ETH_P_PRP) ||
 	    ethhdr->h_proto == htons(ETH_P_HSR)) {
+		/* Check if skb contains hsr_ethhdr */
+		if (skb->mac_len < sizeof(struct hsr_ethhdr))
+			return NULL;
+
 		/* Use the existing sequence_nr from the tag as starting point
 		 * for filtering duplicate frames.
 		 */
@@ -313,6 +318,7 @@
 		goto done;
 
 	ether_addr_copy(node_real->macaddress_B, ethhdr->h_source);
+	spin_lock_bh(&node_real->seq_out_lock);
 	for (i = 0; i < HSR_PT_PORTS; i++) {
 		if (!node_curr->time_in_stale[i] &&
 		    time_after(node_curr->time_in[i], node_real->time_in[i])) {
@@ -323,12 +329,16 @@
 		if (seq_nr_after(node_curr->seq_out[i], node_real->seq_out[i]))
 			node_real->seq_out[i] = node_curr->seq_out[i];
 	}
+	spin_unlock_bh(&node_real->seq_out_lock);
 	node_real->addr_B_port = port_rcv->type;
 
 	spin_lock_bh(&hsr->list_lock);
-	list_del_rcu(&node_curr->mac_list);
+	if (!node_curr->removed) {
+		list_del_rcu(&node_curr->mac_list);
+		node_curr->removed = true;
+		kfree_rcu(node_curr, rcu_head);
+	}
 	spin_unlock_bh(&hsr->list_lock);
-	kfree_rcu(node_curr, rcu_head);
 
 done:
 	/* PRP uses v0 header */
@@ -379,7 +389,7 @@
 	node_dst = find_node_by_addr_A(&port->hsr->node_db,
 				       eth_hdr(skb)->h_dest);
 	if (!node_dst) {
-		if (net_ratelimit())
+		if (port->hsr->prot_version != PRP_V1 && net_ratelimit())
 			netdev_err(skb->dev, "%s: Unknown node\n", __func__);
 		return;
 	}
@@ -416,13 +426,17 @@
 int hsr_register_frame_out(struct hsr_port *port, struct hsr_node *node,
 			   u16 sequence_nr)
 {
+	spin_lock_bh(&node->seq_out_lock);
 	if (seq_nr_before_or_eq(sequence_nr, node->seq_out[port->type]) &&
 	    time_is_after_jiffies(node->time_out[port->type] +
-	    msecs_to_jiffies(HSR_ENTRY_FORGET_TIME)))
+	    msecs_to_jiffies(HSR_ENTRY_FORGET_TIME))) {
+		spin_unlock_bh(&node->seq_out_lock);
 		return 1;
+	}
 
 	node->time_out[port->type] = jiffies;
 	node->seq_out[port->type] = sequence_nr;
+	spin_unlock_bh(&node->seq_out_lock);
 	return 0;
 }
 
@@ -502,9 +516,12 @@
 		if (time_is_before_jiffies(timestamp +
 				msecs_to_jiffies(HSR_NODE_FORGET_TIME))) {
 			hsr_nl_nodedown(hsr, node->macaddress_A);
-			list_del_rcu(&node->mac_list);
-			/* Note that we need to free this entry later: */
-			kfree_rcu(node, rcu_head);
+			if (!node->removed) {
+				list_del_rcu(&node->mac_list);
+				node->removed = true;
+				/* Note that we need to free this entry later: */
+				kfree_rcu(node, rcu_head);
+			}
 		}
 	}
 	spin_unlock_bh(&hsr->list_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/net/hsr/hsr_framereg.h
+++ linux-xilinx-zynqmp-5.15.0/net/hsr/hsr_framereg.h
@@ -69,6 +69,8 @@
 
 struct hsr_node {
 	struct list_head	mac_list;
+	/* Protect R/W access to seq_out */
+	spinlock_t		seq_out_lock;
 	unsigned char		macaddress_A[ETH_ALEN];
 	unsigned char		macaddress_B[ETH_ALEN];
 	/* Local slave through which AddrB frames are received from this node */
@@ -80,6 +82,7 @@
 	bool			san_a;
 	bool			san_b;
 	u16			seq_out[HSR_PT_PORTS];
+	bool			removed;
 	struct rcu_head		rcu_head;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/hsr/hsr_main.c
+++ linux-xilinx-zynqmp-5.15.0/net/hsr/hsr_main.c
@@ -75,7 +75,7 @@
 		master = hsr_port_get_hsr(hsr, HSR_PT_MASTER);
 
 		if (port->type == HSR_PT_SLAVE_A) {
-			ether_addr_copy(master->dev->dev_addr, dev->dev_addr);
+			eth_hw_addr_set(master->dev, dev->dev_addr);
 			call_netdevice_notifiers(NETDEV_CHANGEADDR,
 						 master->dev);
 		}
@@ -148,14 +148,21 @@
 
 static int __init hsr_init(void)
 {
-	int res;
+	int err;
 
 	BUILD_BUG_ON(sizeof(struct hsr_tag) != HSR_HLEN);
 
-	register_netdevice_notifier(&hsr_nb);
-	res = hsr_netlink_init();
+	err = register_netdevice_notifier(&hsr_nb);
+	if (err)
+		return err;
+
+	err = hsr_netlink_init();
+	if (err) {
+		unregister_netdevice_notifier(&hsr_nb);
+		return err;
+	}
 
-	return res;
+	return 0;
 }
 
 static void __exit hsr_exit(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ieee802154/nl802154.c
+++ linux-xilinx-zynqmp-5.15.0/net/ieee802154/nl802154.c
@@ -1441,7 +1441,7 @@
 
 	hdr = nl802154hdr_put(msg, portid, seq, flags, cmd);
 	if (!hdr)
-		return -1;
+		return -ENOBUFS;
 
 	if (nla_put_u32(msg, NL802154_ATTR_IFINDEX, dev->ifindex))
 		goto nla_put_failure;
@@ -1634,7 +1634,7 @@
 
 	hdr = nl802154hdr_put(msg, portid, seq, flags, cmd);
 	if (!hdr)
-		return -1;
+		return -ENOBUFS;
 
 	if (nla_put_u32(msg, NL802154_ATTR_IFINDEX, dev->ifindex))
 		goto nla_put_failure;
@@ -1812,7 +1812,7 @@
 
 	hdr = nl802154hdr_put(msg, portid, seq, flags, cmd);
 	if (!hdr)
-		return -1;
+		return -ENOBUFS;
 
 	if (nla_put_u32(msg, NL802154_ATTR_IFINDEX, dev->ifindex))
 		goto nla_put_failure;
@@ -1988,7 +1988,7 @@
 
 	hdr = nl802154hdr_put(msg, portid, seq, flags, cmd);
 	if (!hdr)
-		return -1;
+		return -ENOBUFS;
 
 	if (nla_put_u32(msg, NL802154_ATTR_IFINDEX, dev->ifindex))
 		goto nla_put_failure;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ieee802154/socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/ieee802154/socket.c
@@ -174,8 +174,8 @@
 {
 	write_lock_bh(&raw_lock);
 	sk_add_node(sk, &raw_head);
-	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 	write_unlock_bh(&raw_lock);
+	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 
 	return 0;
 }
@@ -200,8 +200,9 @@
 	int err = 0;
 	struct net_device *dev = NULL;
 
-	if (len < sizeof(*uaddr))
-		return -EINVAL;
+	err = ieee802154_sockaddr_check_size(uaddr, len);
+	if (err < 0)
+		return err;
 
 	uaddr = (struct sockaddr_ieee802154 *)_uaddr;
 	if (uaddr->family != AF_IEEE802154)
@@ -271,6 +272,10 @@
 		err = -EMSGSIZE;
 		goto out_dev;
 	}
+	if (!size) {
+		err = 0;
+		goto out_dev;
+	}
 
 	hlen = LL_RESERVED_SPACE(dev);
 	tlen = dev->needed_tailroom;
@@ -453,8 +458,8 @@
 {
 	write_lock_bh(&dgram_lock);
 	sk_add_node(sk, &dgram_head);
-	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 	write_unlock_bh(&dgram_lock);
+	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 
 	return 0;
 }
@@ -493,11 +498,14 @@
 
 	ro->bound = 0;
 
-	if (len < sizeof(*addr))
+	err = ieee802154_sockaddr_check_size(addr, len);
+	if (err < 0)
 		goto out;
 
-	if (addr->family != AF_IEEE802154)
+	if (addr->family != AF_IEEE802154) {
+		err = -EINVAL;
 		goto out;
+	}
 
 	ieee802154_addr_from_sa(&haddr, &addr->addr);
 	dev = ieee802154_get_dev(sock_net(sk), &haddr);
@@ -564,8 +572,9 @@
 	struct dgram_sock *ro = dgram_sk(sk);
 	int err = 0;
 
-	if (len < sizeof(*addr))
-		return -EINVAL;
+	err = ieee802154_sockaddr_check_size(addr, len);
+	if (err < 0)
+		return err;
 
 	if (addr->family != AF_IEEE802154)
 		return -EINVAL;
@@ -604,6 +613,7 @@
 	struct ieee802154_mac_cb *cb;
 	struct dgram_sock *ro = dgram_sk(sk);
 	struct ieee802154_addr dst_addr;
+	DECLARE_SOCKADDR(struct sockaddr_ieee802154*, daddr, msg->msg_name);
 	int hlen, tlen;
 	int err;
 
@@ -612,10 +622,20 @@
 		return -EOPNOTSUPP;
 	}
 
-	if (!ro->connected && !msg->msg_name)
-		return -EDESTADDRREQ;
-	else if (ro->connected && msg->msg_name)
-		return -EISCONN;
+	if (msg->msg_name) {
+		if (ro->connected)
+			return -EISCONN;
+		if (msg->msg_namelen < IEEE802154_MIN_NAMELEN)
+			return -EINVAL;
+		err = ieee802154_sockaddr_check_size(daddr, msg->msg_namelen);
+		if (err < 0)
+			return err;
+		ieee802154_addr_from_sa(&dst_addr, &daddr->addr);
+	} else {
+		if (!ro->connected)
+			return -EDESTADDRREQ;
+		dst_addr = ro->dst_addr;
+	}
 
 	if (!ro->bound)
 		dev = dev_getfirstbyhwtype(sock_net(sk), ARPHRD_IEEE802154);
@@ -651,16 +671,6 @@
 	cb = mac_cb_init(skb);
 	cb->type = IEEE802154_FC_TYPE_DATA;
 	cb->ackreq = ro->want_ack;
-
-	if (msg->msg_name) {
-		DECLARE_SOCKADDR(struct sockaddr_ieee802154*,
-				 daddr, msg->msg_name);
-
-		ieee802154_addr_from_sa(&dst_addr, &daddr->addr);
-	} else {
-		dst_addr = ro->dst_addr;
-	}
-
 	cb->secen = ro->secen;
 	cb->secen_override = ro->secen_override;
 	cb->seclevel = ro->seclevel;
@@ -1036,19 +1046,21 @@
 
 	if (sk->sk_prot->hash) {
 		rc = sk->sk_prot->hash(sk);
-		if (rc) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (rc)
+			goto out_sk_release;
 	}
 
 	if (sk->sk_prot->init) {
 		rc = sk->sk_prot->init(sk);
 		if (rc)
-			sk_common_release(sk);
+			goto out_sk_release;
 	}
 out:
 	return rc;
+out_sk_release:
+	sk_common_release(sk);
+	sock->sk = NULL;
+	goto out;
 }
 
 static const struct net_proto_family ieee802154_family_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ife/ife.c
+++ linux-xilinx-zynqmp-5.15.0/net/ife/ife.c
@@ -82,6 +82,7 @@
 	if (unlikely(!pskb_may_pull(skb, total_pull)))
 		return NULL;
 
+	ifehdr = (struct ifeheadr *)(skb->data + skb->dev->hard_header_len);
 	skb_set_mac_header(skb, total_pull);
 	__skb_pull(skb, total_pull);
 	*metalen = ifehdrln - IFE_METAHDRLEN;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/Kconfig
@@ -403,6 +403,16 @@
 
 	  If unsure, say Y.
 
+config INET_TABLE_PERTURB_ORDER
+	int "INET: Source port perturbation table size (as power of 2)" if EXPERT
+	default 16
+	help
+	  Source port perturbation table size (as power of 2) for
+	  RFC 6056 3.3.4.  Algorithm 4: Double-Hash Port Selection Algorithm.
+
+	  The default is almost always what you want.
+	  Only change this if you know what you are doing.
+
 config INET_XFRM_TUNNEL
 	tristate
 	select INET_TUNNEL
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/af_inet.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/af_inet.c
@@ -119,6 +119,7 @@
 #include <net/compat.h>
 
 #include <trace/events/sock.h>
+#include <xen/pvcalls.h>
 
 /* The inetsw table contains everything that inet_create needs to
  * build a new socket.
@@ -158,7 +159,7 @@
 
 	kfree(rcu_dereference_protected(inet->inet_opt, 1));
 	dst_release(rcu_dereference_protected(sk->sk_dst_cache, 1));
-	dst_release(sk->sk_rx_dst);
+	dst_release(rcu_dereference_protected(sk->sk_rx_dst, 1));
 	sk_refcnt_debug_dec(sk);
 }
 EXPORT_SYMBOL(inet_sock_destruct);
@@ -220,7 +221,7 @@
 		 * because the socket was in TCP_LISTEN state previously but
 		 * was shutdown() rather than close().
 		 */
-		tcp_fastopen = sock_net(sk)->ipv4.sysctl_tcp_fastopen;
+		tcp_fastopen = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fastopen);
 		if ((tcp_fastopen & TFO_SERVER_WO_SOCKOPT1) &&
 		    (tcp_fastopen & TFO_SERVER_ENABLE) &&
 		    !inet_csk(sk)->icsk_accept_queue.fastopenq.max_qlen) {
@@ -327,6 +328,9 @@
 	if (INET_PROTOSW_REUSE & answer_flags)
 		sk->sk_reuse = SK_CAN_REUSE;
 
+	if (INET_PROTOSW_ICSK & answer_flags)
+		inet_init_csk_locks(sk);
+
 	inet = inet_sk(sk);
 	inet->is_icsk = (INET_PROTOSW_ICSK & answer_flags) != 0;
 
@@ -338,7 +342,7 @@
 			inet->hdrincl = 1;
 	}
 
-	if (net->ipv4.sysctl_ip_no_pmtu_disc)
+	if (READ_ONCE(net->ipv4.sysctl_ip_no_pmtu_disc))
 		inet->pmtudisc = IP_PMTUDISC_DONT;
 	else
 		inet->pmtudisc = IP_PMTUDISC_WANT;
@@ -370,32 +374,30 @@
 		inet->inet_sport = htons(inet->inet_num);
 		/* Add to protocol hash chains. */
 		err = sk->sk_prot->hash(sk);
-		if (err) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (err)
+			goto out_sk_release;
 	}
 
 	if (sk->sk_prot->init) {
 		err = sk->sk_prot->init(sk);
-		if (err) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (err)
+			goto out_sk_release;
 	}
 
 	if (!kern) {
 		err = BPF_CGROUP_RUN_PROG_INET_SOCK(sk);
-		if (err) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (err)
+			goto out_sk_release;
 	}
 out:
 	return err;
 out_rcu_unlock:
 	rcu_read_unlock();
 	goto out;
+out_sk_release:
+	sk_common_release(sk);
+	sock->sk = NULL;
+	goto out;
 }
 
 
@@ -562,22 +564,27 @@
 		       int addr_len, int flags)
 {
 	struct sock *sk = sock->sk;
+	const struct proto *prot;
 	int err;
 
 	if (addr_len < sizeof(uaddr->sa_family))
 		return -EINVAL;
+
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	prot = READ_ONCE(sk->sk_prot);
+
 	if (uaddr->sa_family == AF_UNSPEC)
-		return sk->sk_prot->disconnect(sk, flags);
+		return prot->disconnect(sk, flags);
 
 	if (BPF_CGROUP_PRE_CONNECT_ENABLED(sk)) {
-		err = sk->sk_prot->pre_connect(sk, uaddr, addr_len);
+		err = prot->pre_connect(sk, uaddr, addr_len);
 		if (err)
 			return err;
 	}
 
 	if (data_race(!inet_sk(sk)->inet_num) && inet_autobind(sk))
 		return -EAGAIN;
-	return sk->sk_prot->connect(sk, uaddr, addr_len);
+	return prot->connect(sk, uaddr, addr_len);
 }
 EXPORT_SYMBOL(inet_dgram_connect);
 
@@ -587,6 +594,7 @@
 
 	add_wait_queue(sk_sleep(sk), &wait);
 	sk->sk_write_pending += writebias;
+	sk->sk_wait_pending++;
 
 	/* Basic assumption: if someone sets sk->sk_err, he _must_
 	 * change state of the socket from TCP_SYN_*.
@@ -602,6 +610,7 @@
 	}
 	remove_wait_queue(sk_sleep(sk), &wait);
 	sk->sk_write_pending -= writebias;
+	sk->sk_wait_pending--;
 	return timeo;
 }
 
@@ -738,10 +747,11 @@
 int inet_accept(struct socket *sock, struct socket *newsock, int flags,
 		bool kern)
 {
-	struct sock *sk1 = sock->sk;
+	struct sock *sk1 = sock->sk, *sk2;
 	int err = -EINVAL;
-	struct sock *sk2 = sk1->sk_prot->accept(sk1, flags, &err, kern);
 
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	sk2 = READ_ONCE(sk1->sk_prot)->accept(sk1, flags, &err, kern);
 	if (!sk2)
 		goto do_err;
 
@@ -750,7 +760,9 @@
 	sock_rps_record_flow(sk2);
 	WARN_ON(!((1 << sk2->sk_state) &
 		  (TCPF_ESTABLISHED | TCPF_SYN_RECV |
-		  TCPF_CLOSE_WAIT | TCPF_CLOSE)));
+		   TCPF_FIN_WAIT1 | TCPF_FIN_WAIT2 |
+		   TCPF_CLOSING | TCPF_CLOSE_WAIT |
+		   TCPF_CLOSE)));
 
 	sock_graft(sk2, newsock);
 
@@ -773,26 +785,28 @@
 	DECLARE_SOCKADDR(struct sockaddr_in *, sin, uaddr);
 
 	sin->sin_family = AF_INET;
+	lock_sock(sk);
 	if (peer) {
 		if (!inet->inet_dport ||
 		    (((1 << sk->sk_state) & (TCPF_CLOSE | TCPF_SYN_SENT)) &&
-		     peer == 1))
+		     peer == 1)) {
+			release_sock(sk);
 			return -ENOTCONN;
+		}
 		sin->sin_port = inet->inet_dport;
 		sin->sin_addr.s_addr = inet->inet_daddr;
-		BPF_CGROUP_RUN_SA_PROG_LOCK(sk, (struct sockaddr *)sin,
-					    CGROUP_INET4_GETPEERNAME,
-					    NULL);
+		BPF_CGROUP_RUN_SA_PROG(sk, (struct sockaddr *)sin,
+				       CGROUP_INET4_GETPEERNAME);
 	} else {
 		__be32 addr = inet->inet_rcv_saddr;
 		if (!addr)
 			addr = inet->inet_saddr;
 		sin->sin_port = inet->inet_sport;
 		sin->sin_addr.s_addr = addr;
-		BPF_CGROUP_RUN_SA_PROG_LOCK(sk, (struct sockaddr *)sin,
-					    CGROUP_INET4_GETSOCKNAME,
-					    NULL);
+		BPF_CGROUP_RUN_SA_PROG(sk, (struct sockaddr *)sin,
+				       CGROUP_INET4_GETSOCKNAME);
 	}
+	release_sock(sk);
 	memset(sin->sin_zero, 0, sizeof(sin->sin_zero));
 	return sizeof(*sin);
 }
@@ -827,12 +841,15 @@
 		      size_t size, int flags)
 {
 	struct sock *sk = sock->sk;
+	const struct proto *prot;
 
 	if (unlikely(inet_send_prepare(sk)))
 		return -EAGAIN;
 
-	if (sk->sk_prot->sendpage)
-		return sk->sk_prot->sendpage(sk, page, offset, size, flags);
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	prot = READ_ONCE(sk->sk_prot);
+	if (prot->sendpage)
+		return prot->sendpage(sk, page, offset, size, flags);
 	return sock_no_sendpage(sock, page, offset, size, flags);
 }
 EXPORT_SYMBOL(inet_sendpage);
@@ -888,7 +905,7 @@
 		   EPOLLHUP, even on eg. unconnected UDP sockets -- RR */
 		fallthrough;
 	default:
-		sk->sk_shutdown |= how;
+		WRITE_ONCE(sk->sk_shutdown, sk->sk_shutdown | how);
 		if (sk->sk_prot->shutdown)
 			sk->sk_prot->shutdown(sk, how);
 		break;
@@ -1249,7 +1266,7 @@
 	if (new_saddr == old_saddr)
 		return 0;
 
-	if (sock_net(sk)->ipv4.sysctl_ip_dynaddr > 1) {
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_ip_dynaddr) > 1) {
 		pr_info("%s(): shifting inet->saddr from %pI4 to %pI4\n",
 			__func__, &old_saddr, &new_saddr);
 	}
@@ -1304,7 +1321,7 @@
 		 * Other protocols have to map its equivalent state to TCP_SYN_SENT.
 		 * DCCP maps its DCCP_REQUESTING state to TCP_SYN_SENT. -acme
 		 */
-		if (!sock_net(sk)->ipv4.sysctl_ip_dynaddr ||
+		if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_ip_dynaddr) ||
 		    sk->sk_state != TCP_SYN_SENT ||
 		    (sk->sk_userlocks & SOCK_BINDADDR_LOCK) ||
 		    (err = inet_sk_reselect_saddr(sk)) != 0)
@@ -1378,8 +1395,11 @@
 	}
 
 	ops = rcu_dereference(inet_offloads[proto]);
-	if (likely(ops && ops->callbacks.gso_segment))
+	if (likely(ops && ops->callbacks.gso_segment)) {
 		segs = ops->callbacks.gso_segment(skb, features);
+		if (!segs)
+			skb->network_header = skb_mac_header(skb) + nhoff - skb->head;
+	}
 
 	if (IS_ERR_OR_NULL(segs))
 		goto out;
@@ -1456,19 +1476,18 @@
 
 	proto = iph->protocol;
 
-	rcu_read_lock();
 	ops = rcu_dereference(inet_offloads[proto]);
 	if (!ops || !ops->callbacks.gro_receive)
-		goto out_unlock;
+		goto out;
 
 	if (*(u8 *)iph != 0x45)
-		goto out_unlock;
+		goto out;
 
 	if (ip_is_fragment(iph))
-		goto out_unlock;
+		goto out;
 
 	if (unlikely(ip_fast_csum((u8 *)iph, 5)))
-		goto out_unlock;
+		goto out;
 
 	id = ntohl(*(__be32 *)&iph->id);
 	flush = (u16)((ntohl(*(__be32 *)iph) ^ skb_gro_len(skb)) | (id & ~IP_DF));
@@ -1545,9 +1564,6 @@
 	pp = indirect_call_gro_receive(tcp4_gro_receive, udp4_gro_receive,
 				       ops->callbacks.gro_receive, head, skb);
 
-out_unlock:
-	rcu_read_unlock();
-
 out:
 	skb_gro_flush_final(skb, pp, flush);
 
@@ -1595,10 +1611,12 @@
 
 int inet_recv_error(struct sock *sk, struct msghdr *msg, int len, int *addr_len)
 {
-	if (sk->sk_family == AF_INET)
+	unsigned int family = READ_ONCE(sk->sk_family);
+
+	if (family == AF_INET)
 		return ip_recv_error(sk, msg, len, addr_len);
 #if IS_ENABLED(CONFIG_IPV6)
-	if (sk->sk_family == AF_INET6)
+	if (family == AF_INET6)
 		return pingv6_ops.ipv6_recv_error(sk, msg, len, addr_len);
 #endif
 	return -EINVAL;
@@ -1620,10 +1638,9 @@
 	csum_replace2(&iph->check, iph->tot_len, newlen);
 	iph->tot_len = newlen;
 
-	rcu_read_lock();
 	ops = rcu_dereference(inet_offloads[proto]);
 	if (WARN_ON(!ops || !ops->callbacks.gro_complete))
-		goto out_unlock;
+		goto out;
 
 	/* Only need to add sizeof(*iph) to get to the next hdr below
 	 * because any hdr with option will have been flushed in
@@ -1633,9 +1650,7 @@
 			      tcp4_gro_complete, udp4_gro_complete,
 			      skb, nhoff + sizeof(*iph));
 
-out_unlock:
-	rcu_read_unlock();
-
+out:
 	return err;
 }
 
@@ -1723,24 +1738,14 @@
 };
 #endif
 
-/* thinking of making this const? Don't.
- * early_demux can change based on sysctl.
- */
-static struct net_protocol tcp_protocol = {
-	.early_demux	=	tcp_v4_early_demux,
-	.early_demux_handler =  tcp_v4_early_demux,
+static const struct net_protocol tcp_protocol = {
 	.handler	=	tcp_v4_rcv,
 	.err_handler	=	tcp_v4_err,
 	.no_policy	=	1,
 	.icmp_strict_tag_validation = 1,
 };
 
-/* thinking of making this const? Don't.
- * early_demux can change based on sysctl.
- */
-static struct net_protocol udp_protocol = {
-	.early_demux =	udp_v4_early_demux,
-	.early_demux_handler =	udp_v4_early_demux,
+static const struct net_protocol udp_protocol = {
 	.handler =	udp_rcv,
 	.err_handler =	udp_err,
 	.no_policy =	1,
@@ -1987,6 +1992,11 @@
 	for (r = &inetsw[0]; r < &inetsw[SOCK_MAX]; ++r)
 		INIT_LIST_HEAD(r);
 
+	if (pvcalls) {
+		pr_info("Enabling pvcalls for AF_INET SOCK_STREAM\n");
+		inetsw_array[0].ops = &pvcalls_stream_ops;
+	}
+
 	for (q = inetsw_array; q < &inetsw_array[INETSW_ARRAY_LEN]; ++q)
 		inet_register_protosw(q);
 
@@ -2002,6 +2012,10 @@
 
 	ip_init();
 
+	/* Initialise per-cpu ipv4 mibs */
+	if (init_ipv4_mibs())
+		panic("%s: Cannot init ipv4 mibs\n", __func__);
+
 	/* Setup TCP slab cache for open requests. */
 	tcp_init();
 
@@ -2032,12 +2046,6 @@
 
 	if (init_inet_pernet_ops())
 		pr_crit("%s: Cannot init ipv4 inet pernet ops\n", __func__);
-	/*
-	 *	Initialise per-cpu ipv4 mibs
-	 */
-
-	if (init_ipv4_mibs())
-		pr_crit("%s: Cannot init ipv4 mibs\n", __func__);
 
 	ipv4_proc_init();
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/arp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/arp.c
@@ -637,10 +637,12 @@
  */
 void arp_xmit(struct sk_buff *skb)
 {
+	rcu_read_lock();
 	/* Send it off, maybe filter it using firewalling first.  */
 	NF_HOOK(NFPROTO_ARP, NF_ARP_OUT,
-		dev_net(skb->dev), NULL, skb, NULL, skb->dev,
+		dev_net_rcu(skb->dev), NULL, skb, NULL, skb->dev,
 		arp_xmit_finish);
+	rcu_read_unlock();
 }
 EXPORT_SYMBOL(arp_xmit);
 
@@ -1007,7 +1009,7 @@
 	if (mask && mask != htonl(0xFFFFFFFF))
 		return -EINVAL;
 	if (!dev && (r->arp_flags & ATF_COM)) {
-		dev = dev_getbyhwaddr_rcu(net, r->arp_ha.sa_family,
+		dev = dev_getbyhwaddr(net, r->arp_ha.sa_family,
 				      r->arp_ha.sa_data);
 		if (!dev)
 			return -ENODEV;
@@ -1104,7 +1106,8 @@
 	if (neigh) {
 		if (!(neigh->nud_state & NUD_NOARP)) {
 			read_lock_bh(&neigh->lock);
-			memcpy(r->arp_ha.sa_data, neigh->ha, dev->addr_len);
+			memcpy(r->arp_ha.sa_data, neigh->ha,
+			       min(dev->addr_len, (unsigned char)sizeof(r->arp_ha.sa_data_min)));
 			r->arp_flags = arp_state_to_flags(neigh);
 			read_unlock_bh(&neigh->lock);
 			r->arp_ha.sa_family = dev->type;
@@ -1116,13 +1119,18 @@
 	return err;
 }
 
-static int arp_invalidate(struct net_device *dev, __be32 ip)
+int arp_invalidate(struct net_device *dev, __be32 ip, bool force)
 {
 	struct neighbour *neigh = neigh_lookup(&arp_tbl, &ip, dev);
 	int err = -ENXIO;
 	struct neigh_table *tbl = &arp_tbl;
 
 	if (neigh) {
+		if ((neigh->nud_state & NUD_VALID) && !force) {
+			neigh_release(neigh);
+			return 0;
+		}
+
 		if (neigh->nud_state & ~NUD_NOARP)
 			err = neigh_update(neigh, NULL, NUD_FAILED,
 					   NEIGH_UPDATE_F_OVERRIDE|
@@ -1169,7 +1177,7 @@
 		if (!dev)
 			return -EINVAL;
 	}
-	return arp_invalidate(dev, ip);
+	return arp_invalidate(dev, ip, true);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/bpf_tcp_ca.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/bpf_tcp_ca.c
@@ -212,6 +212,8 @@
 		    offsetof(struct tcp_congestion_ops, release))
 			return &bpf_sk_getsockopt_proto;
 		return NULL;
+	case BPF_FUNC_ktime_get_coarse_ns:
+		return &bpf_ktime_get_coarse_ns_proto;
 	default:
 		return bpf_base_func_proto(func_id);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/cipso_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/cipso_ipv4.c
@@ -106,15 +106,17 @@
 /* Base length of the local tag (non-standard tag).
  *  Tag definition (may change between kernel versions)
  *
- * 0          8          16         24         32
- * +----------+----------+----------+----------+
- * | 10000000 | 00000110 | 32-bit secid value  |
- * +----------+----------+----------+----------+
- * | in (host byte order)|
- * +----------+----------+
- *
+ * 0          8          16                    16 + sizeof(struct lsmblob)
+ * +----------+----------+---------------------+
+ * | 10000000 | 00000110 | LSM blob data       |
+ * +----------+----------+---------------------+
+ *
+ * All secid and flag fields are in host byte order.
+ * The lsmblob structure size varies depending on which
+ * Linux security modules are built in the kernel.
+ * The data is opaque.
  */
-#define CIPSO_V4_TAG_LOC_BLEN         6
+#define CIPSO_V4_TAG_LOC_BLEN         (2 + sizeof(struct lsmblob))
 
 /*
  * Helper Functions
@@ -239,7 +241,7 @@
 	struct cipso_v4_map_cache_entry *prev_entry = NULL;
 	u32 hash;
 
-	if (!cipso_v4_cache_enabled)
+	if (!READ_ONCE(cipso_v4_cache_enabled))
 		return -ENOENT;
 
 	hash = cipso_v4_map_cache_hash(key, key_len);
@@ -296,13 +298,14 @@
 int cipso_v4_cache_add(const unsigned char *cipso_ptr,
 		       const struct netlbl_lsm_secattr *secattr)
 {
+	int bkt_size = READ_ONCE(cipso_v4_cache_bucketsize);
 	int ret_val = -EPERM;
 	u32 bkt;
 	struct cipso_v4_map_cache_entry *entry = NULL;
 	struct cipso_v4_map_cache_entry *old_entry = NULL;
 	u32 cipso_ptr_len;
 
-	if (!cipso_v4_cache_enabled || cipso_v4_cache_bucketsize <= 0)
+	if (!READ_ONCE(cipso_v4_cache_enabled) || bkt_size <= 0)
 		return 0;
 
 	cipso_ptr_len = cipso_ptr[1];
@@ -322,7 +325,7 @@
 
 	bkt = entry->hash & (CIPSO_V4_CACHE_BUCKETS - 1);
 	spin_lock_bh(&cipso_v4_cache[bkt].lock);
-	if (cipso_v4_cache[bkt].size < cipso_v4_cache_bucketsize) {
+	if (cipso_v4_cache[bkt].size < bkt_size) {
 		list_add(&entry->list, &cipso_v4_cache[bkt].list);
 		cipso_v4_cache[bkt].size += 1;
 	} else {
@@ -1199,7 +1202,8 @@
 		/* This will send packets using the "optimized" format when
 		 * possible as specified in  section 3.4.2.6 of the
 		 * CIPSO draft. */
-		if (cipso_v4_rbm_optfmt && ret_val > 0 && ret_val <= 10)
+		if (READ_ONCE(cipso_v4_rbm_optfmt) && ret_val > 0 &&
+		    ret_val <= 10)
 			tag_len = 14;
 		else
 			tag_len = 4 + ret_val;
@@ -1460,7 +1464,12 @@
 
 	buffer[0] = CIPSO_V4_TAG_LOCAL;
 	buffer[1] = CIPSO_V4_TAG_LOC_BLEN;
-	*(u32 *)&buffer[2] = secattr->attr.secid;
+	/* Ensure that there is sufficient space in the CIPSO header
+	 * for the LSM data. This should never become an issue.
+	 * The check is made from an abundance of caution. */
+	BUILD_BUG_ON(CIPSO_V4_TAG_LOC_BLEN > CIPSO_V4_OPT_LEN_MAX);
+	memcpy(&buffer[2], &secattr->attr.lsmblob,
+	       sizeof(secattr->attr.lsmblob));
 
 	return CIPSO_V4_TAG_LOC_BLEN;
 }
@@ -1480,7 +1489,7 @@
 				 const unsigned char *tag,
 				 struct netlbl_lsm_secattr *secattr)
 {
-	secattr->attr.secid = *(u32 *)&tag[2];
+	memcpy(&secattr->attr.lsmblob, &tag[2], sizeof(secattr->attr.lsmblob));
 	secattr->flags |= NETLBL_SECATTR_SECID;
 
 	return 0;
@@ -1603,7 +1612,7 @@
 			 * all the CIPSO validations here but it doesn't
 			 * really specify _exactly_ what we need to validate
 			 * ... so, just make it a sysctl tunable. */
-			if (cipso_v4_rbm_strictvalid) {
+			if (READ_ONCE(cipso_v4_rbm_strictvalid)) {
 				if (cipso_v4_map_lvl_valid(doi_def,
 							   tag[3]) < 0) {
 					err_offset = opt_iter + 3;
@@ -2013,12 +2022,16 @@
 		 * from there we can determine the new total option length */
 		iter = 0;
 		optlen_new = 0;
-		while (iter < opt->opt.optlen)
-			if (opt->opt.__data[iter] != IPOPT_NOP) {
+		while (iter < opt->opt.optlen) {
+			if (opt->opt.__data[iter] == IPOPT_END) {
+				break;
+			} else if (opt->opt.__data[iter] == IPOPT_NOP) {
+				iter++;
+			} else {
 				iter += opt->opt.__data[iter + 1];
 				optlen_new = iter;
-			} else
-				iter++;
+			}
+		}
 		hdr_delta = opt->opt.optlen;
 		opt->opt.optlen = (optlen_new + 3) & ~3;
 		hdr_delta -= opt->opt.optlen;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/datagram.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/datagram.c
@@ -70,7 +70,7 @@
 	}
 	inet->inet_daddr = fl4->daddr;
 	inet->inet_dport = usin->sin_port;
-	reuseport_has_conns(sk, true);
+	reuseport_has_conns_set(sk);
 	sk->sk_state = TCP_ESTABLISHED;
 	sk_set_txhash(sk);
 	inet->inet_id = prandom_u32();
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/devinet.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/devinet.c
@@ -273,17 +273,19 @@
 	/* Account for reference dev->ip_ptr (below) */
 	refcount_set(&in_dev->refcnt, 1);
 
-	err = devinet_sysctl_register(in_dev);
-	if (err) {
-		in_dev->dead = 1;
-		neigh_parms_release(&arp_tbl, in_dev->arp_parms);
-		in_dev_put(in_dev);
-		in_dev = NULL;
-		goto out;
+	if (dev != blackhole_netdev) {
+		err = devinet_sysctl_register(in_dev);
+		if (err) {
+			in_dev->dead = 1;
+			neigh_parms_release(&arp_tbl, in_dev->arp_parms);
+			in_dev_put(in_dev);
+			in_dev = NULL;
+			goto out;
+		}
+		ip_mc_init_dev(in_dev);
+		if (dev->flags & IFF_UP)
+			ip_mc_up(in_dev);
 	}
-	ip_mc_init_dev(in_dev);
-	if (dev->flags & IFF_UP)
-		ip_mc_up(in_dev);
 
 	/* we can receive as soon as ip_ptr is set -- do this last */
 	rcu_assign_pointer(dev->ip_ptr, in_dev);
@@ -328,6 +330,19 @@
 	call_rcu(&in_dev->rcu_head, in_dev_rcu_put);
 }
 
+static int __init inet_blackhole_dev_init(void)
+{
+	int err = 0;
+
+	rtnl_lock();
+	if (!inetdev_init(blackhole_netdev))
+		err = -ENOMEM;
+	rtnl_unlock();
+
+	return err;
+}
+late_initcall(inet_blackhole_dev_init);
+
 int inet_addr_onlink(struct in_device *in_dev, __be32 a, __be32 b)
 {
 	const struct in_ifaddr *ifa;
@@ -351,14 +366,14 @@
 {
 	struct in_ifaddr *promote = NULL;
 	struct in_ifaddr *ifa, *ifa1;
-	struct in_ifaddr *last_prim;
+	struct in_ifaddr __rcu **last_prim;
 	struct in_ifaddr *prev_prom = NULL;
 	int do_promote = IN_DEV_PROMOTE_SECONDARIES(in_dev);
 
 	ASSERT_RTNL();
 
 	ifa1 = rtnl_dereference(*ifap);
-	last_prim = rtnl_dereference(in_dev->ifa_list);
+	last_prim = ifap;
 	if (in_dev->dead)
 		goto no_promotions;
 
@@ -372,7 +387,7 @@
 		while ((ifa = rtnl_dereference(*ifap1)) != NULL) {
 			if (!(ifa->ifa_flags & IFA_F_SECONDARY) &&
 			    ifa1->ifa_scope <= ifa->ifa_scope)
-				last_prim = ifa;
+				last_prim = &ifa->ifa_next;
 
 			if (!(ifa->ifa_flags & IFA_F_SECONDARY) ||
 			    ifa1->ifa_mask != ifa->ifa_mask ||
@@ -436,9 +451,9 @@
 
 			rcu_assign_pointer(prev_prom->ifa_next, next_sec);
 
-			last_sec = rtnl_dereference(last_prim->ifa_next);
+			last_sec = rtnl_dereference(*last_prim);
 			rcu_assign_pointer(promote->ifa_next, last_sec);
-			rcu_assign_pointer(last_prim->ifa_next, promote);
+			rcu_assign_pointer(*last_prim, promote);
 		}
 
 		promote->ifa_flags &= ~IFA_F_SECONDARY;
@@ -566,10 +581,6 @@
 
 	ASSERT_RTNL();
 
-	if (!in_dev) {
-		inet_free_ifa(ifa);
-		return -ENOBUFS;
-	}
 	ipv4_devconf_setall(in_dev);
 	neigh_parms_data_state_setall(in_dev->arp_parms);
 	if (ifa->ifa_dev != in_dev) {
@@ -1149,6 +1160,8 @@
 
 		if (!ifa) {
 			ret = -ENOBUFS;
+			if (!in_dev)
+				break;
 			ifa = inet_alloc_ifa();
 			if (!ifa)
 				break;
@@ -1303,10 +1316,11 @@
 	__be32 addr = 0;
 	unsigned char localnet_scope = RT_SCOPE_HOST;
 	struct in_device *in_dev;
-	struct net *net = dev_net(dev);
+	struct net *net;
 	int master_idx;
 
 	rcu_read_lock();
+	net = dev_net_rcu(dev);
 	in_dev = __in_dev_get_rcu(dev);
 	if (!in_dev)
 		goto no_in_dev;
@@ -1797,6 +1811,21 @@
 	return err;
 }
 
+/* Combine dev_addr_genid and dev_base_seq to detect changes.
+ */
+static u32 inet_base_seq(const struct net *net)
+{
+	u32 res = atomic_read(&net->ipv4.dev_addr_genid) +
+		  net->dev_base_seq;
+
+	/* Must not return 0 (see nl_dump_check_consistent()).
+	 * Chose a value far away from 0.
+	 */
+	if (!res)
+		res = 0x80000000;
+	return res;
+}
+
 static int inet_dump_ifaddr(struct sk_buff *skb, struct netlink_callback *cb)
 {
 	const struct nlmsghdr *nlh = cb->nlh;
@@ -1848,8 +1877,7 @@
 		idx = 0;
 		head = &tgt_net->dev_index_head[h];
 		rcu_read_lock();
-		cb->seq = atomic_read(&tgt_net->ipv4.dev_addr_genid) ^
-			  tgt_net->dev_base_seq;
+		cb->seq = inet_base_seq(tgt_net);
 		hlist_for_each_entry_rcu(dev, head, index_hlist) {
 			if (idx < s_idx)
 				goto cont;
@@ -2250,8 +2278,7 @@
 		idx = 0;
 		head = &net->dev_index_head[h];
 		rcu_read_lock();
-		cb->seq = atomic_read(&net->ipv4.dev_addr_genid) ^
-			  net->dev_base_seq;
+		cb->seq = inet_base_seq(net);
 		hlist_for_each_entry_rcu(dev, head, index_hlist) {
 			if (idx < s_idx)
 				goto cont;
@@ -2587,7 +2614,7 @@
 free:
 	kfree(t);
 out:
-	return -ENOBUFS;
+	return -ENOMEM;
 }
 
 static void __devinet_sysctl_unregister(struct net *net,
@@ -2673,23 +2700,27 @@
 #endif
 
 	if (!net_eq(net, &init_net)) {
-		if (IS_ENABLED(CONFIG_SYSCTL) &&
-		    sysctl_devconf_inherit_init_net == 3) {
+		switch (net_inherit_devconf()) {
+		case 3:
 			/* copy from the current netns */
 			memcpy(all, current->nsproxy->net_ns->ipv4.devconf_all,
 			       sizeof(ipv4_devconf));
 			memcpy(dflt,
 			       current->nsproxy->net_ns->ipv4.devconf_dflt,
 			       sizeof(ipv4_devconf_dflt));
-		} else if (!IS_ENABLED(CONFIG_SYSCTL) ||
-			   sysctl_devconf_inherit_init_net != 2) {
-			/* inherit == 0 or 1: copy from init_net */
+			break;
+		case 0:
+		case 1:
+			/* copy from init_net */
 			memcpy(all, init_net.ipv4.devconf_all,
 			       sizeof(ipv4_devconf));
 			memcpy(dflt, init_net.ipv4.devconf_dflt,
 			       sizeof(ipv4_devconf_dflt));
+			break;
+		case 2:
+			/* use compiled values */
+			break;
 		}
-		/* else inherit == 2: use compiled values */
 	}
 
 #ifdef CONFIG_SYSCTL
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/esp4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/esp4.c
@@ -237,8 +237,7 @@
 #else
 static int esp_output_tail_tcp(struct xfrm_state *x, struct sk_buff *skb)
 {
-	kfree_skb(skb);
-
+	WARN_ON(1);
 	return -EOPNOTSUPP;
 }
 #endif
@@ -455,6 +454,10 @@
 			return err;
 	}
 
+	if (ALIGN(tailen, L1_CACHE_BYTES) > PAGE_SIZE ||
+	    ALIGN(skb->data_len, L1_CACHE_BYTES) > PAGE_SIZE)
+		goto cow;
+
 	if (!skb_cloned(skb)) {
 		if (tailen <= skb_tailroom(skb)) {
 			nfrags = 1;
@@ -671,7 +674,7 @@
 		struct xfrm_dst *dst = (struct xfrm_dst *)skb_dst(skb);
 		u32 padto;
 
-		padto = min(x->tfcpad, __xfrm_state_mtu(x, dst->child_mtu_cached));
+		padto = min(x->tfcpad, xfrm_state_mtu(x, dst->child_mtu_cached));
 		if (skb->len < padto)
 			esp.tfclen = padto - skb->len;
 	}
@@ -735,7 +738,9 @@
 		skb->csum = csum_block_sub(skb->csum, csumdiff,
 					   skb->len - trimlen);
 	}
-	pskb_trim(skb, skb->len - trimlen);
+	ret = pskb_trim(skb, skb->len - trimlen);
+	if (unlikely(ret))
+		return ret;
 
 	ret = nexthdr[1];
 
@@ -1129,7 +1134,7 @@
 	err = crypto_aead_setkey(aead, key, keylen);
 
 free_key:
-	kfree(key);
+	kfree_sensitive(key);
 
 error:
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/esp4_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/esp4_offload.c
@@ -159,6 +159,9 @@
 			skb_shinfo(skb)->gso_type |= SKB_GSO_TCPV4;
 	}
 
+	if (proto == IPPROTO_IPV6)
+		skb_shinfo(skb)->gso_type |= SKB_GSO_IPXIP4;
+
 	__skb_pull(skb, skb_transport_offset(skb));
 	ops = rcu_dereference(inet_offloads[proto]);
 	if (likely(ops && ops->callbacks.gso_segment))
@@ -308,6 +311,9 @@
 			xo->seq.low += skb_shinfo(skb)->gso_segs;
 	}
 
+	if (xo->seq.low < seq)
+		xo->seq.hi++;
+
 	esp.seqno = cpu_to_be64(seq + ((u64)xo->seq.hi << 32));
 
 	ip_hdr(skb)->tot_len = htons(skb->len);
@@ -331,6 +337,9 @@
 
 	secpath_reset(skb);
 
+	if (skb_needs_linearize(skb, skb->dev->features) &&
+	    __skb_linearize(skb))
+		return -ENOMEM;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/fib_frontend.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/fib_frontend.c
@@ -290,7 +290,7 @@
 		bool vmark = in_dev && IN_DEV_SRC_VMARK(in_dev);
 		struct flowi4 fl4 = {
 			.flowi4_iif = LOOPBACK_IFINDEX,
-			.flowi4_oif = l3mdev_master_ifindex_rcu(dev),
+			.flowi4_l3mdev = l3mdev_master_ifindex_rcu(dev),
 			.daddr = ip_hdr(skb)->saddr,
 			.flowi4_tos = ip_hdr(skb)->tos & IPTOS_RT_MASK,
 			.flowi4_scope = scope,
@@ -352,9 +352,8 @@
 	bool dev_match;
 
 	fl4.flowi4_oif = 0;
-	fl4.flowi4_iif = l3mdev_master_ifindex_rcu(dev);
-	if (!fl4.flowi4_iif)
-		fl4.flowi4_iif = oif ? : LOOPBACK_IFINDEX;
+	fl4.flowi4_l3mdev = l3mdev_master_ifindex_rcu(dev);
+	fl4.flowi4_iif = oif ? : LOOPBACK_IFINDEX;
 	fl4.daddr = src;
 	fl4.saddr = dst;
 	fl4.flowi4_tos = tos;
@@ -389,7 +388,7 @@
 	dev_match = dev_match || (res.type == RTN_LOCAL &&
 				  dev == net->loopback_dev);
 	if (dev_match) {
-		ret = FIB_RES_NHC(res)->nhc_scope >= RT_SCOPE_HOST;
+		ret = FIB_RES_NHC(res)->nhc_scope >= RT_SCOPE_LINK;
 		return ret;
 	}
 	if (no_addr)
@@ -401,7 +400,7 @@
 	ret = 0;
 	if (fib_lookup(net, &fl4, &res, FIB_LOOKUP_IGNORE_LINKSTATE) == 0) {
 		if (res.type == RTN_UNICAST)
-			ret = FIB_RES_NHC(res)->nhc_scope >= RT_SCOPE_HOST;
+			ret = FIB_RES_NHC(res)->nhc_scope >= RT_SCOPE_LINK;
 	}
 	return ret;
 
@@ -573,6 +572,9 @@
 			cfg->fc_scope = RT_SCOPE_UNIVERSE;
 	}
 
+	if (!cfg->fc_table)
+		cfg->fc_table = RT_TABLE_MAIN;
+
 	if (cmd == SIOCDELRT)
 		return 0;
 
@@ -830,6 +832,9 @@
 		return -EINVAL;
 	}
 
+	if (!cfg->fc_table)
+		cfg->fc_table = RT_TABLE_MAIN;
+
 	return 0;
 errout:
 	return err;
@@ -1112,9 +1117,11 @@
 		return;
 
 	/* Add broadcast address, if it is explicitly assigned. */
-	if (ifa->ifa_broadcast && ifa->ifa_broadcast != htonl(0xFFFFFFFF))
+	if (ifa->ifa_broadcast && ifa->ifa_broadcast != htonl(0xFFFFFFFF)) {
 		fib_magic(RTM_NEWROUTE, RTN_BROADCAST, ifa->ifa_broadcast, 32,
 			  prim, 0);
+		arp_invalidate(dev, ifa->ifa_broadcast, false);
+	}
 
 	if (!ipv4_is_zeronet(prefix) && !(ifa->ifa_flags & IFA_F_SECONDARY) &&
 	    (prefix != addr || ifa->ifa_prefixlen < 32)) {
@@ -1128,6 +1135,7 @@
 		if (ifa->ifa_prefixlen < 31) {
 			fib_magic(RTM_NEWROUTE, RTN_BROADCAST, prefix | ~mask,
 				  32, prim, 0);
+			arp_invalidate(dev, prefix | ~mask, false);
 		}
 	}
 }
@@ -1323,7 +1331,7 @@
 	struct flowi4           fl4 = {
 		.flowi4_mark = frn->fl_mark,
 		.daddr = frn->fl_addr,
-		.flowi4_tos = frn->fl_tos,
+		.flowi4_tos = frn->fl_tos & IPTOS_RT_MASK,
 		.flowi4_scope = frn->fl_scope,
 	};
 	struct fib_table *tb;
@@ -1582,7 +1590,7 @@
 	int error;
 
 #ifdef CONFIG_IP_ROUTE_CLASSID
-	net->ipv4.fib_num_tclassid_users = 0;
+	atomic_set(&net->ipv4.fib_num_tclassid_users, 0);
 #endif
 	error = ip_fib_net_init(net);
 	if (error < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/fib_lookup.h
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/fib_lookup.h
@@ -16,10 +16,9 @@
 	u8			fa_slen;
 	u32			tb_id;
 	s16			fa_default;
-	u8			offload:1,
-				trap:1,
-				offload_failed:1,
-				unused:5;
+	u8			offload;
+	u8			trap;
+	u8			offload_failed;
 	struct rcu_head		rcu;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/fib_rules.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/fib_rules.c
@@ -141,6 +141,7 @@
 }
 
 INDIRECT_CALLABLE_SCOPE bool fib4_rule_suppress(struct fib_rule *rule,
+						int flags,
 						struct fib_lookup_arg *arg)
 {
 	struct fib_result *result = (struct fib_result *) arg->result;
@@ -263,7 +264,7 @@
 	if (tb[FRA_FLOW]) {
 		rule4->tclassid = nla_get_u32(tb[FRA_FLOW]);
 		if (rule4->tclassid)
-			net->ipv4.fib_num_tclassid_users++;
+			atomic_inc(&net->ipv4.fib_num_tclassid_users);
 	}
 #endif
 
@@ -295,7 +296,7 @@
 
 #ifdef CONFIG_IP_ROUTE_CLASSID
 	if (((struct fib4_rule *)rule)->tclassid)
-		net->ipv4.fib_num_tclassid_users--;
+		atomic_dec(&net->ipv4.fib_num_tclassid_users);
 #endif
 	net->ipv4.fib_has_custom_rules = true;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/fib_semantics.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/fib_semantics.c
@@ -29,6 +29,8 @@
 #include <linux/init.h>
 #include <linux/slab.h>
 #include <linux/netlink.h>
+#include <linux/hash.h>
+#include <linux/nospec.h>
 
 #include <net/arp.h>
 #include <net/ip.h>
@@ -220,7 +222,7 @@
 {
 #ifdef CONFIG_IP_ROUTE_CLASSID
 	if (fib_nh->nh_tclassid)
-		net->ipv4.fib_num_tclassid_users--;
+		atomic_dec(&net->ipv4.fib_num_tclassid_users);
 #endif
 	fib_nh_common_release(&fib_nh->nh_common);
 }
@@ -249,7 +251,6 @@
 		pr_warn("Freeing alive fib_info %p\n", fi);
 		return;
 	}
-	fib_info_cnt--;
 
 	call_rcu(&fi->rcu, free_fib_info_rcu);
 }
@@ -260,6 +261,10 @@
 	spin_lock_bh(&fib_info_lock);
 	if (fi && refcount_dec_and_test(&fi->fib_treeref)) {
 		hlist_del(&fi->fib_hash);
+
+		/* Paired with READ_ONCE() in fib_create_info(). */
+		WRITE_ONCE(fib_info_cnt, fib_info_cnt - 1);
+
 		if (fi->fib_prefsrc)
 			hlist_del(&fi->fib_lhash);
 		if (fi->nh) {
@@ -271,7 +276,8 @@
 				hlist_del(&nexthop_nh->nh_hash);
 			} endfor_nexthops(fi)
 		}
-		fi->fib_dead = 1;
+		/* Paired with READ_ONCE() from fib_table_lookup() */
+		WRITE_ONCE(fi->fib_dead, 1);
 		fib_info_put(fi);
 	}
 	spin_unlock_bh(&fib_info_lock);
@@ -316,11 +322,15 @@
 
 static inline unsigned int fib_devindex_hashfn(unsigned int val)
 {
-	unsigned int mask = DEVINDEX_HASHSIZE - 1;
+	return hash_32(val, DEVINDEX_HASHBITS);
+}
+
+static struct hlist_head *
+fib_info_devhash_bucket(const struct net_device *dev)
+{
+	u32 val = net_hash_mix(dev_net(dev)) ^ dev->ifindex;
 
-	return (val ^
-		(val >> DEVINDEX_HASHBITS) ^
-		(val >> (DEVINDEX_HASHBITS * 2))) & mask;
+	return &fib_info_devhash[fib_devindex_hashfn(val)];
 }
 
 static unsigned int fib_info_hashfn_1(int init_val, u8 protocol, u8 scope,
@@ -413,6 +423,7 @@
 		    nfi->fib_prefsrc == fi->fib_prefsrc &&
 		    nfi->fib_priority == fi->fib_priority &&
 		    nfi->fib_type == fi->fib_type &&
+		    nfi->fib_tb_id == fi->fib_tb_id &&
 		    memcmp(nfi->fib_metrics, fi->fib_metrics,
 			   sizeof(u32) * RTAX_MAX) == 0 &&
 		    !((nfi->fib_flags ^ fi->fib_flags) & ~RTNH_COMPARE_MASK) &&
@@ -430,12 +441,11 @@
 {
 	struct hlist_head *head;
 	struct fib_nh *nh;
-	unsigned int hash;
 
 	spin_lock(&fib_info_lock);
 
-	hash = fib_devindex_hashfn(dev->ifindex);
-	head = &fib_info_devhash[hash];
+	head = fib_info_devhash_bucket(dev);
+
 	hlist_for_each_entry(nh, head, nh_hash) {
 		if (nh->fib_nh_dev == dev &&
 		    nh->fib_nh_gw4 == gw &&
@@ -517,9 +527,9 @@
 	fri.dst_len = dst_len;
 	fri.tos = fa->fa_tos;
 	fri.type = fa->fa_type;
-	fri.offload = fa->offload;
-	fri.trap = fa->trap;
-	fri.offload_failed = fa->offload_failed;
+	fri.offload = READ_ONCE(fa->offload);
+	fri.trap = READ_ONCE(fa->trap);
+	fri.offload_failed = READ_ONCE(fa->offload_failed);
 	err = fib_dump_info(skb, info->portid, seq, event, &fri, nlm_flags);
 	if (err < 0) {
 		/* -EMSGSIZE implies BUG in fib_nlmsg_size() */
@@ -632,7 +642,7 @@
 #ifdef CONFIG_IP_ROUTE_CLASSID
 	nh->nh_tclassid = cfg->fc_flow;
 	if (nh->nh_tclassid)
-		net->ipv4.fib_num_tclassid_users++;
+		atomic_inc(&net->ipv4.fib_num_tclassid_users);
 #endif
 #ifdef CONFIG_IP_ROUTE_MULTIPATH
 	nh->fib_nh_weight = nh_weight;
@@ -662,6 +672,19 @@
 	return nhs;
 }
 
+static int fib_gw_from_attr(__be32 *gw, struct nlattr *nla,
+			    struct netlink_ext_ack *extack)
+{
+	if (nla_len(nla) < sizeof(*gw)) {
+		NL_SET_ERR_MSG(extack, "Invalid IPv4 address in RTA_GATEWAY");
+		return -EINVAL;
+	}
+
+	*gw = nla_get_in_addr(nla);
+
+	return 0;
+}
+
 /* only called when fib_nh is integrated into fib_info */
 static int fib_get_nhs(struct fib_info *fi, struct rtnexthop *rtnh,
 		       int remaining, struct fib_config *cfg,
@@ -704,7 +727,11 @@
 				return -EINVAL;
 			}
 			if (nla) {
-				fib_cfg.fc_gw4 = nla_get_in_addr(nla);
+				ret = fib_gw_from_attr(&fib_cfg.fc_gw4, nla,
+						       extack);
+				if (ret)
+					goto errout;
+
 				if (fib_cfg.fc_gw4)
 					fib_cfg.fc_gw_family = AF_INET;
 			} else if (nlav) {
@@ -714,10 +741,18 @@
 			}
 
 			nla = nla_find(attrs, attrlen, RTA_FLOW);
-			if (nla)
+			if (nla) {
+				if (nla_len(nla) < sizeof(u32)) {
+					NL_SET_ERR_MSG(extack, "Invalid RTA_FLOW");
+					return -EINVAL;
+				}
 				fib_cfg.fc_flow = nla_get_u32(nla);
+			}
 
 			fib_cfg.fc_encap = nla_find(attrs, attrlen, RTA_ENCAP);
+			/* RTA_ENCAP_TYPE length checked in
+			 * lwtunnel_valid_encap_type_attr
+			 */
 			nla = nla_find(attrs, attrlen, RTA_ENCAP_TYPE);
 			if (nla)
 				fib_cfg.fc_encap_type = nla_get_u16(nla);
@@ -854,9 +889,16 @@
 		return 1;
 	}
 
+	if (fi->nh) {
+		if (cfg->fc_oif || cfg->fc_gw_family || cfg->fc_mp)
+			return 1;
+		return 0;
+	}
+
 	if (cfg->fc_oif || cfg->fc_gw_family) {
-		struct fib_nh *nh = fib_info_nh(fi, 0);
+		struct fib_nh *nh;
 
+		nh = fib_info_nh(fi, 0);
 		if (cfg->fc_encap) {
 			if (fib_encap_match(net, cfg->fc_encap_type,
 					    cfg->fc_encap, nh, cfg, extack))
@@ -902,6 +944,7 @@
 		attrlen = rtnh_attrlen(rtnh);
 		if (attrlen > 0) {
 			struct nlattr *nla, *nlav, *attrs = rtnh_attrs(rtnh);
+			int err;
 
 			nla = nla_find(attrs, attrlen, RTA_GATEWAY);
 			nlav = nla_find(attrs, attrlen, RTA_VIA);
@@ -912,12 +955,17 @@
 			}
 
 			if (nla) {
+				__be32 gw;
+
+				err = fib_gw_from_attr(&gw, nla, extack);
+				if (err)
+					return err;
+
 				if (nh->fib_nh_gw_family != AF_INET ||
-				    nla_get_in_addr(nla) != nh->fib_nh_gw4)
+				    gw != nh->fib_nh_gw4)
 					return 1;
 			} else if (nlav) {
 				struct fib_config cfg2;
-				int err;
 
 				err = fib_gw_from_via(&cfg2, nlav, extack);
 				if (err)
@@ -940,8 +988,14 @@
 
 #ifdef CONFIG_IP_ROUTE_CLASSID
 			nla = nla_find(attrs, attrlen, RTA_FLOW);
-			if (nla && nla_get_u32(nla) != nh->nh_tclassid)
-				return 1;
+			if (nla) {
+				if (nla_len(nla) < sizeof(u32)) {
+					NL_SET_ERR_MSG(extack, "Invalid RTA_FLOW");
+					return -EINVAL;
+				}
+				if (nla_get_u32(nla) != nh->nh_tclassid)
+					return 1;
+			}
 #endif
 		}
 
@@ -968,6 +1022,7 @@
 		if (type > RTAX_MAX)
 			return false;
 
+		type = array_index_nospec(type, RTAX_MAX + 1);
 		if (type == RTAX_CC_ALGO) {
 			char tmp[TCP_CA_NAME_MAX];
 			bool ecn_ca = false;
@@ -1179,7 +1234,7 @@
 
 	nh->fib_nh_dev = in_dev->dev;
 	dev_hold(nh->fib_nh_dev);
-	nh->fib_nh_scope = RT_SCOPE_HOST;
+	nh->fib_nh_scope = RT_SCOPE_LINK;
 	if (!netif_carrier_ok(nh->fib_nh_dev))
 		nh->fib_nh_flags |= RTNH_F_LINKDOWN;
 	err = 0;
@@ -1289,15 +1344,18 @@
 				 unsigned char scope)
 {
 	struct fib_nh *nh;
+	__be32 saddr;
 
 	if (nhc->nhc_family != AF_INET)
 		return inet_select_addr(nhc->nhc_dev, 0, scope);
 
 	nh = container_of(nhc, struct fib_nh, nh_common);
-	nh->nh_saddr = inet_select_addr(nh->fib_nh_dev, nh->fib_nh_gw4, scope);
-	nh->nh_saddr_genid = atomic_read(&net->ipv4.dev_addr_genid);
+	saddr = inet_select_addr(nh->fib_nh_dev, nh->fib_nh_gw4, scope);
+
+	WRITE_ONCE(nh->nh_saddr, saddr);
+	WRITE_ONCE(nh->nh_saddr_genid, atomic_read(&net->ipv4.dev_addr_genid));
 
-	return nh->nh_saddr;
+	return saddr;
 }
 
 __be32 fib_result_prefsrc(struct net *net, struct fib_result *res)
@@ -1311,8 +1369,9 @@
 		struct fib_nh *nh;
 
 		nh = container_of(nhc, struct fib_nh, nh_common);
-		if (nh->nh_saddr_genid == atomic_read(&net->ipv4.dev_addr_genid))
-			return nh->nh_saddr;
+		if (READ_ONCE(nh->nh_saddr_genid) ==
+		    atomic_read(&net->ipv4.dev_addr_genid))
+			return READ_ONCE(nh->nh_saddr);
 	}
 
 	return fib_info_update_nhc_saddr(net, nhc, res->fi->fib_scope);
@@ -1393,7 +1452,9 @@
 #endif
 
 	err = -ENOBUFS;
-	if (fib_info_cnt >= fib_info_hash_size) {
+
+	/* Paired with WRITE_ONCE() in fib_release_info() */
+	if (READ_ONCE(fib_info_cnt) >= fib_info_hash_size) {
 		unsigned int new_size = fib_info_hash_size << 1;
 		struct hlist_head *new_info_hash;
 		struct hlist_head *new_laddrhash;
@@ -1425,7 +1486,6 @@
 		return ERR_PTR(err);
 	}
 
-	fib_info_cnt++;
 	fi->fib_net = net;
 	fi->fib_protocol = cfg->fc_protocol;
 	fi->fib_scope = cfg->fc_scope;
@@ -1543,6 +1603,7 @@
 link_it:
 	ofi = fib_find_info(fi);
 	if (ofi) {
+		/* fib_table_lookup() should not see @fi yet. */
 		fi->fib_dead = 1;
 		free_fib_info(fi);
 		refcount_inc(&ofi->fib_treeref);
@@ -1552,6 +1613,7 @@
 	refcount_set(&fi->fib_treeref, 1);
 	refcount_set(&fi->fib_clntref, 1);
 	spin_lock_bh(&fib_info_lock);
+	fib_info_cnt++;
 	hlist_add_head(&fi->fib_hash,
 		       &fib_info_hash[fib_info_hashfn(fi)]);
 	if (fi->fib_prefsrc) {
@@ -1565,12 +1627,10 @@
 	} else {
 		change_nexthops(fi) {
 			struct hlist_head *head;
-			unsigned int hash;
 
 			if (!nexthop_nh->fib_nh_dev)
 				continue;
-			hash = fib_devindex_hashfn(nexthop_nh->fib_nh_dev->ifindex);
-			head = &fib_info_devhash[hash];
+			head = fib_info_devhash_bucket(nexthop_nh->fib_nh_dev);
 			hlist_add_head(&nexthop_nh->nh_hash, head);
 		} endfor_nexthops(fi)
 	}
@@ -1582,6 +1642,7 @@
 
 failure:
 	if (fi) {
+		/* fib_table_lookup() should not see @fi yet. */
 		fi->fib_dead = 1;
 		free_fib_info(fi);
 	}
@@ -1780,7 +1841,7 @@
 			goto nla_put_failure;
 		if (nexthop_is_blackhole(fi->nh))
 			rtm->rtm_type = RTN_BLACKHOLE;
-		if (!fi->fib_net->ipv4.sysctl_nexthop_compat_mode)
+		if (!READ_ONCE(fi->fib_net->ipv4.sysctl_nexthop_compat_mode))
 			goto offload;
 	}
 
@@ -1847,6 +1908,7 @@
 			continue;
 		if (fi->fib_prefsrc == local) {
 			fi->fib_flags |= RTNH_F_DEAD;
+			fi->pfsrc_removed = true;
 			ret++;
 		}
 	}
@@ -1922,8 +1984,7 @@
 
 void fib_sync_mtu(struct net_device *dev, u32 orig_mtu)
 {
-	unsigned int hash = fib_devindex_hashfn(dev->ifindex);
-	struct hlist_head *head = &fib_info_devhash[hash];
+	struct hlist_head *head = fib_info_devhash_bucket(dev);
 	struct fib_nh *nh;
 
 	hlist_for_each_entry(nh, head, nh_hash) {
@@ -1942,12 +2003,11 @@
  */
 int fib_sync_down_dev(struct net_device *dev, unsigned long event, bool force)
 {
-	int ret = 0;
-	int scope = RT_SCOPE_NOWHERE;
+	struct hlist_head *head = fib_info_devhash_bucket(dev);
 	struct fib_info *prev_fi = NULL;
-	unsigned int hash = fib_devindex_hashfn(dev->ifindex);
-	struct hlist_head *head = &fib_info_devhash[hash];
+	int scope = RT_SCOPE_NOWHERE;
 	struct fib_nh *nh;
+	int ret = 0;
 
 	if (force)
 		scope = -1;
@@ -2092,7 +2152,6 @@
 int fib_sync_up(struct net_device *dev, unsigned char nh_flags)
 {
 	struct fib_info *prev_fi;
-	unsigned int hash;
 	struct hlist_head *head;
 	struct fib_nh *nh;
 	int ret;
@@ -2108,8 +2167,7 @@
 	}
 
 	prev_fi = NULL;
-	hash = fib_devindex_hashfn(dev->ifindex);
-	head = &fib_info_devhash[hash];
+	head = fib_info_devhash_bucket(dev);
 	ret = 0;
 
 	hlist_for_each_entry(nh, head, nh_hash) {
@@ -2188,7 +2246,7 @@
 	}
 
 	change_nexthops(fi) {
-		if (net->ipv4.sysctl_fib_multipath_use_neigh) {
+		if (READ_ONCE(net->ipv4.sysctl_fib_multipath_use_neigh)) {
 			if (!fib_good_nh(nexthop_nh))
 				continue;
 			if (!first) {
@@ -2211,7 +2269,7 @@
 void fib_select_path(struct net *net, struct fib_result *res,
 		     struct flowi4 *fl4, const struct sk_buff *skb)
 {
-	if (fl4->flowi4_oif && !(fl4->flowi4_flags & FLOWI_FLAG_SKIP_NH_OIF))
+	if (fl4->flowi4_oif)
 		goto check_saddr;
 
 #ifdef CONFIG_IP_ROUTE_MULTIPATH
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/fib_trie.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/fib_trie.c
@@ -497,7 +497,7 @@
 		tn = container_of(head, struct tnode, rcu)->kv;
 	}
 
-	if (tnode_free_size >= sysctl_fib_sync_mem) {
+	if (tnode_free_size >= READ_ONCE(sysctl_fib_sync_mem)) {
 		tnode_free_size = 0;
 		synchronize_rcu();
 	}
@@ -1037,6 +1037,7 @@
 
 void fib_alias_hw_flags_set(struct net *net, const struct fib_rt_info *fri)
 {
+	u8 fib_notify_on_flag_change;
 	struct fib_alias *fa_match;
 	struct sk_buff *skb;
 	int err;
@@ -1047,21 +1048,27 @@
 	if (!fa_match)
 		goto out;
 
-	if (fa_match->offload == fri->offload && fa_match->trap == fri->trap &&
-	    fa_match->offload_failed == fri->offload_failed)
+	/* These are paired with the WRITE_ONCE() happening in this function.
+	 * The reason is that we are only protected by RCU at this point.
+	 */
+	if (READ_ONCE(fa_match->offload) == fri->offload &&
+	    READ_ONCE(fa_match->trap) == fri->trap &&
+	    READ_ONCE(fa_match->offload_failed) == fri->offload_failed)
 		goto out;
 
-	fa_match->offload = fri->offload;
-	fa_match->trap = fri->trap;
+	WRITE_ONCE(fa_match->offload, fri->offload);
+	WRITE_ONCE(fa_match->trap, fri->trap);
+
+	fib_notify_on_flag_change = READ_ONCE(net->ipv4.sysctl_fib_notify_on_flag_change);
 
 	/* 2 means send notifications only if offload_failed was changed. */
-	if (net->ipv4.sysctl_fib_notify_on_flag_change == 2 &&
-	    fa_match->offload_failed == fri->offload_failed)
+	if (fib_notify_on_flag_change == 2 &&
+	    READ_ONCE(fa_match->offload_failed) == fri->offload_failed)
 		goto out;
 
-	fa_match->offload_failed = fri->offload_failed;
+	WRITE_ONCE(fa_match->offload_failed, fri->offload_failed);
 
-	if (!net->ipv4.sysctl_fib_notify_on_flag_change)
+	if (!fib_notify_on_flag_change)
 		goto out;
 
 	skb = nlmsg_new(fib_nlmsg_size(fa_match->fa_info), GFP_ATOMIC);
@@ -1368,8 +1375,10 @@
 
 	/* The alias was already inserted, so the node must exist. */
 	l = l ? l : fib_find_node(t, &tp, key);
-	if (WARN_ON_ONCE(!l))
+	if (WARN_ON_ONCE(!l)) {
+		err = -ENOENT;
 		goto out_free_new_fa;
+	}
 
 	if (fib_find_alias(&l->leaf, new_fa->fa_slen, 0, 0, tb->tb_id, true) ==
 	    new_fa) {
@@ -1419,11 +1428,8 @@
 	    !(fib_flags & FIB_LOOKUP_IGNORE_LINKSTATE))
 		return false;
 
-	if (!(flp->flowi4_flags & FLOWI_FLAG_SKIP_NH_OIF)) {
-		if (flp->flowi4_oif &&
-		    flp->flowi4_oif != nhc->nhc_oif)
-			return false;
-	}
+	if (flp->flowi4_oif && flp->flowi4_oif != nhc->nhc_oif)
+		return false;
 
 	return true;
 }
@@ -1569,7 +1575,8 @@
 		}
 		if (fa->fa_tos && fa->fa_tos != flp->flowi4_tos)
 			continue;
-		if (fi->fib_dead)
+		/* Paired with WRITE_ONCE() in fib_release_info() */
+		if (READ_ONCE(fi->fib_dead))
 			continue;
 		if (fa->fa_info->fib_scope < flp->flowi4_scope)
 			continue;
@@ -2011,6 +2018,7 @@
 int fib_table_flush(struct net *net, struct fib_table *tb, bool flush_all)
 {
 	struct trie *t = (struct trie *)tb->tb_data;
+	struct nl_info info = { .nl_net = net };
 	struct key_vector *pn = t->kv;
 	unsigned long cindex = 1;
 	struct hlist_node *tmp;
@@ -2073,6 +2081,9 @@
 
 			fib_notify_alias_delete(net, n->key, &n->leaf, fa,
 						NULL);
+			if (fi->pfsrc_removed)
+				rtmsg_fib(RTM_DELROUTE, htonl(n->key), fa,
+					  KEYLENGTH - fa->fa_slen, tb->tb_id, &info, 0);
 			hlist_del_rcu(&fa->fa_list);
 			fib_release_info(fa->fa_info);
 			alias_free_mem_rcu(fa);
@@ -2297,9 +2308,9 @@
 				fri.dst_len = KEYLENGTH - fa->fa_slen;
 				fri.tos = fa->fa_tos;
 				fri.type = fa->fa_type;
-				fri.offload = fa->offload;
-				fri.trap = fa->trap;
-				fri.offload_failed = fa->offload_failed;
+				fri.offload = READ_ONCE(fa->offload);
+				fri.trap = READ_ONCE(fa->trap);
+				fri.offload_failed = READ_ONCE(fa->offload_failed);
 				err = fib_dump_info(skb,
 						    NETLINK_CB(cb->skb).portid,
 						    cb->nlh->nlmsg_seq,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/fou.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/fou.c
@@ -48,7 +48,7 @@
 
 static inline struct fou *fou_from_sock(struct sock *sk)
 {
-	return sk->sk_user_data;
+	return rcu_dereference_sk_user_data(sk);
 }
 
 static int fou_recv_pull(struct sk_buff *skb, struct fou *fou, size_t len)
@@ -231,9 +231,15 @@
 				       struct sk_buff *skb)
 {
 	const struct net_offload __rcu **offloads;
-	u8 proto = fou_from_sock(sk)->protocol;
+	struct fou *fou = fou_from_sock(sk);
 	const struct net_offload *ops;
 	struct sk_buff *pp = NULL;
+	u8 proto;
+
+	if (!fou)
+		goto out;
+
+	proto = fou->protocol;
 
 	/* We can clear the encap_mark for FOU as we are essentially doing
 	 * one of two possible things.  We are either adding an L4 tunnel
@@ -246,17 +252,14 @@
 	/* Flag this frame as already having an outer encap header */
 	NAPI_GRO_CB(skb)->is_fou = 1;
 
-	rcu_read_lock();
 	offloads = NAPI_GRO_CB(skb)->is_ipv6 ? inet6_offloads : inet_offloads;
 	ops = rcu_dereference(offloads[proto]);
 	if (!ops || !ops->callbacks.gro_receive)
-		goto out_unlock;
+		goto out;
 
 	pp = call_gro_receive(ops->callbacks.gro_receive, head, skb);
 
-out_unlock:
-	rcu_read_unlock();
-
+out:
 	return pp;
 }
 
@@ -264,23 +267,30 @@
 			    int nhoff)
 {
 	const struct net_offload __rcu **offloads;
-	u8 proto = fou_from_sock(sk)->protocol;
+	struct fou *fou = fou_from_sock(sk);
 	const struct net_offload *ops;
-	int err = -ENOSYS;
+	u8 proto;
+	int err;
+
+	if (!fou) {
+		err = -ENOENT;
+		goto out;
+	}
+
+	proto = fou->protocol;
 
-	rcu_read_lock();
 	offloads = NAPI_GRO_CB(skb)->is_ipv6 ? inet6_offloads : inet_offloads;
 	ops = rcu_dereference(offloads[proto]);
-	if (WARN_ON(!ops || !ops->callbacks.gro_complete))
-		goto out_unlock;
+	if (WARN_ON(!ops || !ops->callbacks.gro_complete)) {
+		err = -ENOSYS;
+		goto out;
+	}
 
 	err = ops->callbacks.gro_complete(skb, nhoff);
 
 	skb_set_inner_mac_header(skb, nhoff);
 
-out_unlock:
-	rcu_read_unlock();
-
+out:
 	return err;
 }
 
@@ -326,6 +336,9 @@
 
 	skb_gro_remcsum_init(&grc);
 
+	if (!fou)
+		goto out;
+
 	off = skb_gro_offset(skb);
 	len = off + sizeof(*guehdr);
 
@@ -438,17 +451,14 @@
 	/* Flag this frame as already having an outer encap header */
 	NAPI_GRO_CB(skb)->is_fou = 1;
 
-	rcu_read_lock();
 	offloads = NAPI_GRO_CB(skb)->is_ipv6 ? inet6_offloads : inet_offloads;
 	ops = rcu_dereference(offloads[proto]);
-	if (WARN_ON_ONCE(!ops || !ops->callbacks.gro_receive))
-		goto out_unlock;
+	if (!ops || !ops->callbacks.gro_receive)
+		goto out;
 
 	pp = call_gro_receive(ops->callbacks.gro_receive, head, skb);
 	flush = 0;
 
-out_unlock:
-	rcu_read_unlock();
 out:
 	skb_gro_flush_final_remcsum(skb, pp, flush, &grc);
 
@@ -485,18 +495,16 @@
 		return err;
 	}
 
-	rcu_read_lock();
 	offloads = NAPI_GRO_CB(skb)->is_ipv6 ? inet6_offloads : inet_offloads;
 	ops = rcu_dereference(offloads[proto]);
 	if (WARN_ON(!ops || !ops->callbacks.gro_complete))
-		goto out_unlock;
+		goto out;
 
 	err = ops->callbacks.gro_complete(skb, nhoff + guehlen);
 
 	skb_set_inner_mac_header(skb, nhoff + guehlen);
 
-out_unlock:
-	rcu_read_unlock();
+out:
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/gre_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/gre_offload.c
@@ -162,10 +162,9 @@
 
 	type = greh->protocol;
 
-	rcu_read_lock();
 	ptype = gro_find_receive_by_type(type);
 	if (!ptype)
-		goto out_unlock;
+		goto out;
 
 	grehlen = GRE_HEADER_SECTION;
 
@@ -179,13 +178,13 @@
 	if (skb_gro_header_hard(skb, hlen)) {
 		greh = skb_gro_header_slow(skb, hlen, off);
 		if (unlikely(!greh))
-			goto out_unlock;
+			goto out;
 	}
 
 	/* Don't bother verifying checksum if we're going to flush anyway. */
 	if ((greh->flags & GRE_CSUM) && !NAPI_GRO_CB(skb)->flush) {
 		if (skb_gro_checksum_simple_validate(skb))
-			goto out_unlock;
+			goto out;
 
 		skb_gro_checksum_try_convert(skb, IPPROTO_GRE,
 					     null_compute_pseudo);
@@ -229,8 +228,6 @@
 	pp = call_gro_receive(ptype->callbacks.gro_receive, head, skb);
 	flush = 0;
 
-out_unlock:
-	rcu_read_unlock();
 out:
 	skb_gro_flush_final(skb, pp, flush);
 
@@ -255,13 +252,10 @@
 	if (greh->flags & GRE_CSUM)
 		grehlen += GRE_HEADER_SECTION;
 
-	rcu_read_lock();
 	ptype = gro_find_complete_by_type(type);
 	if (ptype)
 		err = ptype->callbacks.gro_complete(skb, nhoff + grehlen);
 
-	rcu_read_unlock();
-
 	skb_set_inner_mac_header(skb, nhoff + grehlen);
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/icmp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/icmp.c
@@ -92,6 +92,7 @@
 #include <net/inet_common.h>
 #include <net/ip_fib.h>
 #include <net/l3mdev.h>
+#include <net/addrconf.h>
 
 /*
  *	Build xmit assembly blocks
@@ -261,11 +262,12 @@
 	spin_lock(&icmp_global.lock);
 	delta = min_t(u32, now - icmp_global.stamp, HZ);
 	if (delta >= HZ / 50) {
-		incr = sysctl_icmp_msgs_per_sec * delta / HZ ;
+		incr = READ_ONCE(sysctl_icmp_msgs_per_sec) * delta / HZ;
 		if (incr)
 			WRITE_ONCE(icmp_global.stamp, now);
 	}
-	credit = min_t(u32, icmp_global.credit + incr, sysctl_icmp_msgs_burst);
+	credit = min_t(u32, icmp_global.credit + incr,
+		       READ_ONCE(sysctl_icmp_msgs_burst));
 	if (credit) {
 		/* We want to use a credit of one in average, but need to randomize
 		 * it for security reasons.
@@ -289,7 +291,7 @@
 		return true;
 
 	/* Limit if icmp type is enabled in ratemask. */
-	if (!((1 << type) & net->ipv4.sysctl_icmp_ratemask))
+	if (!((1 << type) & READ_ONCE(net->ipv4.sysctl_icmp_ratemask)))
 		return true;
 
 	return false;
@@ -327,7 +329,8 @@
 
 	vif = l3mdev_master_ifindex(dst->dev);
 	peer = inet_getpeer_v4(net->ipv4.peers, fl4->daddr, vif, 1);
-	rc = inet_peer_xrlim_allow(peer, net->ipv4.sysctl_icmp_ratelimit);
+	rc = inet_peer_xrlim_allow(peer,
+				   READ_ONCE(net->ipv4.sysctl_icmp_ratelimit));
 	if (peer)
 		inet_putpeer(peer);
 out:
@@ -701,7 +704,7 @@
 
 		rcu_read_lock();
 		if (rt_is_input_route(rt) &&
-		    net->ipv4.sysctl_icmp_errors_use_inbound_ifaddr)
+		    READ_ONCE(net->ipv4.sysctl_icmp_errors_use_inbound_ifaddr))
 			dev = dev_get_by_index_rcu(net, inet_iif(skb_in));
 
 		if (dev)
@@ -753,6 +756,11 @@
 		room = 576;
 	room -= sizeof(struct iphdr) + icmp_param.replyopts.opt.opt.optlen;
 	room -= sizeof(struct icmphdr);
+	/* Guard against tiny mtu. We need to include at least one
+	 * IP network header for this message to make any sense.
+	 */
+	if (room <= (int)sizeof(struct iphdr))
+		goto ende;
 
 	icmp_param.data_len = skb_in->len - icmp_param.offset;
 	if (icmp_param.data_len > room)
@@ -885,7 +893,7 @@
 			 * values please see
 			 * Documentation/networking/ip-sysctl.rst
 			 */
-			switch (net->ipv4.sysctl_ip_no_pmtu_disc) {
+			switch (READ_ONCE(net->ipv4.sysctl_ip_no_pmtu_disc)) {
 			default:
 				net_dbg_ratelimited("%pI4: fragmentation needed and DF set\n",
 						    &iph->daddr);
@@ -938,7 +946,7 @@
 	 *	get the other vendor to fix their kit.
 	 */
 
-	if (!net->ipv4.sysctl_icmp_ignore_bogus_error_responses &&
+	if (!READ_ONCE(net->ipv4.sysctl_icmp_ignore_bogus_error_responses) &&
 	    inet_addr_type_dev_table(net, skb->dev, iph->daddr) == RTN_BROADCAST) {
 		net_warn_ratelimited("%pI4 sent an invalid ICMP type %u, code %u error to a broadcast: %pI4 on %s\n",
 				     &ip_hdr(skb)->saddr,
@@ -1028,12 +1036,14 @@
 	struct icmp_ext_hdr *ext_hdr, _ext_hdr;
 	struct icmp_ext_echo_iio *iio, _iio;
 	struct net *net = dev_net(skb->dev);
+	struct inet6_dev *in6_dev;
+	struct in_device *in_dev;
 	struct net_device *dev;
 	char buff[IFNAMSIZ];
 	u16 ident_len;
 	u8 status;
 
-	if (!net->ipv4.sysctl_icmp_echo_enable_probe)
+	if (!READ_ONCE(net->ipv4.sysctl_icmp_echo_enable_probe))
 		return false;
 
 	/* We currently only support probing interfaces on the proxy node
@@ -1111,10 +1121,15 @@
 	/* Fill bits in reply message */
 	if (dev->flags & IFF_UP)
 		status |= ICMP_EXT_ECHOREPLY_ACTIVE;
-	if (__in_dev_get_rcu(dev) && __in_dev_get_rcu(dev)->ifa_list)
+
+	in_dev = __in_dev_get_rcu(dev);
+	if (in_dev && rcu_access_pointer(in_dev->ifa_list))
 		status |= ICMP_EXT_ECHOREPLY_IPV4;
-	if (!list_empty(&rcu_dereference(dev->ip6_ptr)->addr_list))
+
+	in6_dev = __in6_dev_get(dev);
+	if (in6_dev && !list_empty(&in6_dev->addr_list))
 		status |= ICMP_EXT_ECHOREPLY_IPV6;
+
 	dev_put(dev);
 	icmphdr->un.echo.sequence |= htons(status);
 	return true;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/igmp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/igmp.c
@@ -216,8 +216,10 @@
 	int tv = prandom_u32() % max_delay;
 
 	im->tm_running = 1;
-	if (!mod_timer(&im->timer, jiffies+tv+2))
-		refcount_inc(&im->refcnt);
+	if (refcount_inc_not_zero(&im->refcnt)) {
+		if (mod_timer(&im->timer, jiffies + tv + 2))
+			ip_ma_put(im);
+	}
 }
 
 static void igmp_gq_start_timer(struct in_device *in_dev)
@@ -353,8 +355,9 @@
 	struct flowi4 fl4;
 	int hlen = LL_RESERVED_SPACE(dev);
 	int tlen = dev->needed_tailroom;
-	unsigned int size = mtu;
+	unsigned int size;
 
+	size = min(mtu, IP_MAX_MTU);
 	while (1) {
 		skb = alloc_skb(size + hlen + tlen,
 				GFP_ATOMIC | __GFP_NOWARN);
@@ -467,7 +470,8 @@
 
 	if (pmc->multiaddr == IGMP_ALL_HOSTS)
 		return skb;
-	if (ipv4_is_local_multicast(pmc->multiaddr) && !net->ipv4.sysctl_igmp_llm_reports)
+	if (ipv4_is_local_multicast(pmc->multiaddr) &&
+	    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 		return skb;
 
 	mtu = READ_ONCE(dev->mtu);
@@ -593,7 +597,7 @@
 			if (pmc->multiaddr == IGMP_ALL_HOSTS)
 				continue;
 			if (ipv4_is_local_multicast(pmc->multiaddr) &&
-			     !net->ipv4.sysctl_igmp_llm_reports)
+			    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 				continue;
 			spin_lock_bh(&pmc->lock);
 			if (pmc->sfcount[MCAST_EXCLUDE])
@@ -736,7 +740,8 @@
 	if (type == IGMPV3_HOST_MEMBERSHIP_REPORT)
 		return igmpv3_send_report(in_dev, pmc);
 
-	if (ipv4_is_local_multicast(group) && !net->ipv4.sysctl_igmp_llm_reports)
+	if (ipv4_is_local_multicast(group) &&
+	    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 		return 0;
 
 	if (type == IGMP_HOST_LEAVE_MESSAGE)
@@ -825,7 +830,7 @@
 	struct net *net = dev_net(in_dev->dev);
 	if (IGMP_V1_SEEN(in_dev) || IGMP_V2_SEEN(in_dev))
 		return;
-	WRITE_ONCE(in_dev->mr_ifc_count, in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv);
+	WRITE_ONCE(in_dev->mr_ifc_count, in_dev->mr_qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv));
 	igmp_ifc_start_timer(in_dev, 1);
 }
 
@@ -920,7 +925,8 @@
 
 	if (group == IGMP_ALL_HOSTS)
 		return false;
-	if (ipv4_is_local_multicast(group) && !net->ipv4.sysctl_igmp_llm_reports)
+	if (ipv4_is_local_multicast(group) &&
+	    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 		return false;
 
 	rcu_read_lock();
@@ -1006,7 +1012,7 @@
 		 * received value was zero, use the default or statically
 		 * configured value.
 		 */
-		in_dev->mr_qrv = ih3->qrv ?: net->ipv4.sysctl_igmp_qrv;
+		in_dev->mr_qrv = ih3->qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 		in_dev->mr_qi = IGMPV3_QQIC(ih3->qqic)*HZ ?: IGMP_QUERY_INTERVAL;
 
 		/* RFC3376, 8.3. Query Response Interval:
@@ -1045,7 +1051,7 @@
 		if (im->multiaddr == IGMP_ALL_HOSTS)
 			continue;
 		if (ipv4_is_local_multicast(im->multiaddr) &&
-		    !net->ipv4.sysctl_igmp_llm_reports)
+		    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 			continue;
 		spin_lock_bh(&im->lock);
 		if (im->tm_running)
@@ -1186,7 +1192,7 @@
 	pmc->interface = im->interface;
 	in_dev_hold(in_dev);
 	pmc->multiaddr = im->multiaddr;
-	pmc->crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+	pmc->crcount = in_dev->mr_qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 	pmc->sfmode = im->sfmode;
 	if (pmc->sfmode == MCAST_INCLUDE) {
 		struct ip_sf_list *psf;
@@ -1237,9 +1243,11 @@
 			swap(im->tomb, pmc->tomb);
 			swap(im->sources, pmc->sources);
 			for (psf = im->sources; psf; psf = psf->sf_next)
-				psf->sf_crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+				psf->sf_crcount = in_dev->mr_qrv ?:
+					READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 		} else {
-			im->crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+			im->crcount = in_dev->mr_qrv ?:
+				READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 		}
 		in_dev_put(pmc->interface);
 		kfree_pmc(pmc);
@@ -1296,7 +1304,8 @@
 #ifdef CONFIG_IP_MULTICAST
 	if (im->multiaddr == IGMP_ALL_HOSTS)
 		return;
-	if (ipv4_is_local_multicast(im->multiaddr) && !net->ipv4.sysctl_igmp_llm_reports)
+	if (ipv4_is_local_multicast(im->multiaddr) &&
+	    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 		return;
 
 	reporter = im->reporter;
@@ -1338,13 +1347,14 @@
 #ifdef CONFIG_IP_MULTICAST
 	if (im->multiaddr == IGMP_ALL_HOSTS)
 		return;
-	if (ipv4_is_local_multicast(im->multiaddr) && !net->ipv4.sysctl_igmp_llm_reports)
+	if (ipv4_is_local_multicast(im->multiaddr) &&
+	    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 		return;
 
 	if (in_dev->dead)
 		return;
 
-	im->unsolicit_count = net->ipv4.sysctl_igmp_qrv;
+	im->unsolicit_count = READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 	if (IGMP_V1_SEEN(in_dev) || IGMP_V2_SEEN(in_dev)) {
 		spin_lock_bh(&im->lock);
 		igmp_start_timer(im, IGMP_INITIAL_REPORT_DELAY);
@@ -1358,7 +1368,7 @@
 	 * IN() to IN(A).
 	 */
 	if (im->sfmode == MCAST_EXCLUDE)
-		im->crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+		im->crcount = in_dev->mr_qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 
 	igmp_ifc_event(in_dev);
 #endif
@@ -1642,7 +1652,7 @@
 		if (im->multiaddr == IGMP_ALL_HOSTS)
 			continue;
 		if (ipv4_is_local_multicast(im->multiaddr) &&
-		    !net->ipv4.sysctl_igmp_llm_reports)
+		    !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
 			continue;
 
 		/* a failover is happening and switches
@@ -1749,7 +1759,7 @@
 
 	in_dev->mr_qi = IGMP_QUERY_INTERVAL;
 	in_dev->mr_qri = IGMP_QUERY_RESPONSE_INTERVAL;
-	in_dev->mr_qrv = net->ipv4.sysctl_igmp_qrv;
+	in_dev->mr_qrv = READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 }
 #else
 static void ip_mc_reset(struct in_device *in_dev)
@@ -1883,7 +1893,7 @@
 #ifdef CONFIG_IP_MULTICAST
 		if (psf->sf_oldin &&
 		    !IGMP_V1_SEEN(in_dev) && !IGMP_V2_SEEN(in_dev)) {
-			psf->sf_crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+			psf->sf_crcount = in_dev->mr_qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 			psf->sf_next = pmc->tomb;
 			pmc->tomb = psf;
 			rv = 1;
@@ -1947,7 +1957,7 @@
 		/* filter mode change */
 		pmc->sfmode = MCAST_INCLUDE;
 #ifdef CONFIG_IP_MULTICAST
-		pmc->crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+		pmc->crcount = in_dev->mr_qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 		WRITE_ONCE(in_dev->mr_ifc_count, pmc->crcount);
 		for (psf = pmc->sources; psf; psf = psf->sf_next)
 			psf->sf_crcount = 0;
@@ -2126,7 +2136,7 @@
 #ifdef CONFIG_IP_MULTICAST
 		/* else no filters; keep old mode for reports */
 
-		pmc->crcount = in_dev->mr_qrv ?: net->ipv4.sysctl_igmp_qrv;
+		pmc->crcount = in_dev->mr_qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
 		WRITE_ONCE(in_dev->mr_ifc_count, pmc->crcount);
 		for (psf = pmc->sources; psf; psf = psf->sf_next)
 			psf->sf_crcount = 0;
@@ -2192,7 +2202,7 @@
 		count++;
 	}
 	err = -ENOBUFS;
-	if (count >= net->ipv4.sysctl_igmp_max_memberships)
+	if (count >= READ_ONCE(net->ipv4.sysctl_igmp_max_memberships))
 		goto done;
 	iml = sock_kmalloc(sk, sizeof(*iml), GFP_KERNEL);
 	if (!iml)
@@ -2379,7 +2389,7 @@
 	}
 	/* else, add a new source to the filter */
 
-	if (psl && psl->sl_count >= net->ipv4.sysctl_igmp_max_msf) {
+	if (psl && psl->sl_count >= READ_ONCE(net->ipv4.sysctl_igmp_max_msf)) {
 		err = -ENOBUFS;
 		goto done;
 	}
@@ -2403,9 +2413,10 @@
 			/* decrease mem now to avoid the memleak warning */
 			atomic_sub(struct_size(psl, sl_addr, psl->sl_max),
 				   &sk->sk_omem_alloc);
-			kfree_rcu(psl, rcu);
 		}
 		rcu_assign_pointer(pmc->sflist, newpsl);
+		if (psl)
+			kfree_rcu(psl, rcu);
 		psl = newpsl;
 	}
 	rv = 1;	/* > 0 for insert logic below if sl_count is 0 */
@@ -2507,11 +2518,13 @@
 		/* decrease mem now to avoid the memleak warning */
 		atomic_sub(struct_size(psl, sl_addr, psl->sl_max),
 			   &sk->sk_omem_alloc);
-		kfree_rcu(psl, rcu);
-	} else
+	} else {
 		(void) ip_mc_del_src(in_dev, &msf->imsf_multiaddr, pmc->sfmode,
 			0, NULL, 0);
+	}
 	rcu_assign_pointer(pmc->sflist, newpsl);
+	if (psl)
+		kfree_rcu(psl, rcu);
 	pmc->sfmode = msf->imsf_fmode;
 	err = 0;
 done:
@@ -2519,11 +2532,10 @@
 		err = ip_mc_leave_group(sk, &imr);
 	return err;
 }
-
 int ip_mc_msfget(struct sock *sk, struct ip_msfilter *msf,
-	struct ip_msfilter __user *optval, int __user *optlen)
+		 sockptr_t optval, sockptr_t optlen)
 {
-	int err, len, count, copycount;
+	int err, len, count, copycount, msf_size;
 	struct ip_mreqn	imr;
 	__be32 addr = msf->imsf_multiaddr;
 	struct ip_mc_socklist *pmc;
@@ -2566,12 +2578,15 @@
 	copycount = count < msf->imsf_numsrc ? count : msf->imsf_numsrc;
 	len = flex_array_size(psl, sl_addr, copycount);
 	msf->imsf_numsrc = count;
-	if (put_user(IP_MSFILTER_SIZE(copycount), optlen) ||
-	    copy_to_user(optval, msf, IP_MSFILTER_SIZE(0))) {
+	msf_size = IP_MSFILTER_SIZE(copycount);
+	if (copy_to_sockptr(optlen, &msf_size, sizeof(int)) ||
+	    copy_to_sockptr(optval, msf, IP_MSFILTER_SIZE(0))) {
 		return -EFAULT;
 	}
 	if (len &&
-	    copy_to_user(&optval->imsf_slist_flex[0], psl->sl_addr, len))
+	    copy_to_sockptr_offset(optval,
+				   offsetof(struct ip_msfilter, imsf_slist_flex),
+				   psl->sl_addr, len))
 		return -EFAULT;
 	return 0;
 done:
@@ -2579,7 +2594,7 @@
 }
 
 int ip_mc_gsfget(struct sock *sk, struct group_filter *gsf,
-	struct sockaddr_storage __user *p)
+		 sockptr_t optval, size_t ss_offset)
 {
 	int i, count, copycount;
 	struct sockaddr_in *psin;
@@ -2609,15 +2624,17 @@
 	count = psl ? psl->sl_count : 0;
 	copycount = count < gsf->gf_numsrc ? count : gsf->gf_numsrc;
 	gsf->gf_numsrc = count;
-	for (i = 0; i < copycount; i++, p++) {
+	for (i = 0; i < copycount; i++) {
 		struct sockaddr_storage ss;
 
 		psin = (struct sockaddr_in *)&ss;
 		memset(&ss, 0, sizeof(ss));
 		psin->sin_family = AF_INET;
 		psin->sin_addr.s_addr = psl->sl_addr[i];
-		if (copy_to_user(p, &ss, sizeof(ss)))
+		if (copy_to_sockptr_offset(optval, ss_offset,
+					   &ss, sizeof(ss)))
 			return -EFAULT;
+		ss_offset += sizeof(ss);
 	}
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/inet_connection_sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/inet_connection_sock.c
@@ -155,10 +155,14 @@
 	 */
 
 	sk_for_each_bound(sk2, &tb->owners) {
-		if (sk != sk2 &&
-		    (!sk->sk_bound_dev_if ||
-		     !sk2->sk_bound_dev_if ||
-		     sk->sk_bound_dev_if == sk2->sk_bound_dev_if)) {
+		int bound_dev_if2;
+
+		if (sk == sk2)
+			continue;
+		bound_dev_if2 = READ_ONCE(sk2->sk_bound_dev_if);
+		if ((!sk->sk_bound_dev_if ||
+		     !bound_dev_if2 ||
+		     sk->sk_bound_dev_if == bound_dev_if2)) {
 			if (reuse && sk2->sk_reuse &&
 			    sk2->sk_state != TCP_LISTEN) {
 				if ((!relax ||
@@ -259,7 +263,7 @@
 		goto other_half_scan;
 	}
 
-	if (net->ipv4.sysctl_ip_autobind_reuse && !relax) {
+	if (READ_ONCE(net->ipv4.sysctl_ip_autobind_reuse) && !relax) {
 		/* We still have a chance to connect to different destinations */
 		relax = true;
 		goto ports_exhausted;
@@ -541,6 +545,10 @@
 	}
 	if (req)
 		reqsk_put(req);
+
+	if (newsk)
+		inet_init_csk_locks(newsk);
+
 	return newsk;
 out_err:
 	newsk = NULL;
@@ -581,6 +589,20 @@
 }
 EXPORT_SYMBOL(inet_csk_clear_xmit_timers);
 
+void inet_csk_clear_xmit_timers_sync(struct sock *sk)
+{
+	struct inet_connection_sock *icsk = inet_csk(sk);
+
+	/* ongoing timer handlers need to acquire socket lock. */
+	sock_not_owned_by_me(sk);
+
+	icsk->icsk_pending = icsk->icsk_ack.pending = 0;
+
+	sk_stop_timer_sync(sk, &icsk->icsk_retransmit_timer);
+	sk_stop_timer_sync(sk, &icsk->icsk_delack_timer);
+	sk_stop_timer_sync(sk, &sk->sk_timer);
+}
+
 void inet_csk_delete_keepalive_timer(struct sock *sk)
 {
 	sk_stop_timer(sk, &sk->sk_timer);
@@ -721,7 +743,7 @@
 
 	sk_node_init(&nreq_sk->sk_node);
 	nreq_sk->sk_tx_queue_mapping = req_sk->sk_tx_queue_mapping;
-#ifdef CONFIG_XPS
+#ifdef CONFIG_SOCK_RX_QUEUE_MAPPING
 	nreq_sk->sk_rx_queue_mapping = req_sk->sk_rx_queue_mapping;
 #endif
 	nreq_sk->sk_incoming_cpu = req_sk->sk_incoming_cpu;
@@ -769,21 +791,31 @@
 		found = __sk_nulls_del_node_init_rcu(req_to_sk(req));
 		spin_unlock(lock);
 	}
-	if (timer_pending(&req->rsk_timer) && del_timer_sync(&req->rsk_timer))
-		reqsk_put(req);
+
 	return found;
 }
 
-bool inet_csk_reqsk_queue_drop(struct sock *sk, struct request_sock *req)
+static bool __inet_csk_reqsk_queue_drop(struct sock *sk,
+					struct request_sock *req,
+					bool from_timer)
 {
 	bool unlinked = reqsk_queue_unlink(req);
 
+	if (!from_timer && timer_delete_sync(&req->rsk_timer))
+		reqsk_put(req);
+
 	if (unlinked) {
 		reqsk_queue_removed(&inet_csk(sk)->icsk_accept_queue, req);
 		reqsk_put(req);
 	}
+
 	return unlinked;
 }
+
+bool inet_csk_reqsk_queue_drop(struct sock *sk, struct request_sock *req)
+{
+	return __inet_csk_reqsk_queue_drop(sk, req, false);
+}
 EXPORT_SYMBOL(inet_csk_reqsk_queue_drop);
 
 void inet_csk_reqsk_queue_drop_and_put(struct sock *sk, struct request_sock *req)
@@ -829,7 +861,8 @@
 
 	icsk = inet_csk(sk_listener);
 	net = sock_net(sk_listener);
-	max_syn_ack_retries = icsk->icsk_syn_retries ? : net->ipv4.sysctl_tcp_synack_retries;
+	max_syn_ack_retries = READ_ONCE(icsk->icsk_syn_retries) ? :
+		READ_ONCE(net->ipv4.sysctl_tcp_synack_retries);
 	/* Normally all the openreqs are young and become mature
 	 * (i.e. converted to established socket) for first timeout.
 	 * If synack was not acknowledged for 1 second, it means
@@ -866,19 +899,16 @@
 	    (!resend ||
 	     !inet_rtx_syn_ack(sk_listener, req) ||
 	     inet_rsk(req)->acked)) {
-		unsigned long timeo;
-
 		if (req->num_timeout++ == 0)
 			atomic_dec(&queue->young);
-		timeo = min(TCP_TIMEOUT_INIT << req->num_timeout, TCP_RTO_MAX);
-		mod_timer(&req->rsk_timer, jiffies + timeo);
+		mod_timer(&req->rsk_timer, jiffies + reqsk_timeout(req, TCP_RTO_MAX));
 
 		if (!nreq)
 			return;
 
 		if (!inet_ehash_insert(req_to_sk(nreq), req_to_sk(oreq), NULL)) {
 			/* delete timer */
-			inet_csk_reqsk_queue_drop(sk_listener, nreq);
+			__inet_csk_reqsk_queue_drop(sk_listener, nreq, true);
 			goto no_ownership;
 		}
 
@@ -904,28 +934,38 @@
 	}
 
 drop:
-	inet_csk_reqsk_queue_drop_and_put(oreq->rsk_listener, oreq);
+	__inet_csk_reqsk_queue_drop(sk_listener, oreq, true);
+	reqsk_put(oreq);
 }
 
-static void reqsk_queue_hash_req(struct request_sock *req,
+static bool reqsk_queue_hash_req(struct request_sock *req,
 				 unsigned long timeout)
 {
+	bool found_dup_sk = false;
+
+	if (!inet_ehash_insert(req_to_sk(req), NULL, &found_dup_sk))
+		return false;
+
+	/* The timer needs to be setup after a successful insertion. */
 	timer_setup(&req->rsk_timer, reqsk_timer_handler, TIMER_PINNED);
 	mod_timer(&req->rsk_timer, jiffies + timeout);
 
-	inet_ehash_insert(req_to_sk(req), NULL, NULL);
 	/* before letting lookups find us, make sure all req fields
 	 * are committed to memory and refcnt initialized.
 	 */
 	smp_wmb();
 	refcount_set(&req->rsk_refcnt, 2 + 1);
+	return true;
 }
 
-void inet_csk_reqsk_queue_hash_add(struct sock *sk, struct request_sock *req,
+bool inet_csk_reqsk_queue_hash_add(struct sock *sk, struct request_sock *req,
 				   unsigned long timeout)
 {
-	reqsk_queue_hash_req(req, timeout);
+	if (!reqsk_queue_hash_req(req, timeout))
+		return false;
+
 	inet_csk_reqsk_queue_added(sk);
+	return true;
 }
 EXPORT_SYMBOL_GPL(inet_csk_reqsk_queue_hash_add);
 
@@ -958,6 +998,7 @@
 	if (newsk) {
 		struct inet_connection_sock *newicsk = inet_csk(newsk);
 
+		newsk->sk_wait_pending = 0;
 		inet_sk_set_state(newsk, TCP_SYN_RECV);
 		newicsk->icsk_bind_hash = NULL;
 
@@ -1015,7 +1056,7 @@
 
 	sk_refcnt_debug_release(sk);
 
-	percpu_counter_dec(sk->sk_prot->orphan_count);
+	this_cpu_dec(*sk->sk_prot->orphan_count);
 
 	sock_put(sk);
 }
@@ -1035,11 +1076,25 @@
 }
 EXPORT_SYMBOL(inet_csk_prepare_forced_close);
 
+static int inet_ulp_can_listen(const struct sock *sk)
+{
+	const struct inet_connection_sock *icsk = inet_csk(sk);
+
+	if (icsk->icsk_ulp_ops && !icsk->icsk_ulp_ops->clone)
+		return -EINVAL;
+
+	return 0;
+}
+
 int inet_csk_listen_start(struct sock *sk, int backlog)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct inet_sock *inet = inet_sk(sk);
-	int err = -EADDRINUSE;
+	int err;
+
+	err = inet_ulp_can_listen(sk);
+	if (unlikely(err))
+		return err;
 
 	reqsk_queue_alloc(&icsk->icsk_accept_queue);
 
@@ -1051,7 +1106,10 @@
 	 * It is OK, because this socket enters to hash table only
 	 * after validation is complete.
 	 */
+	err = -EADDRINUSE;
 	inet_sk_state_store(sk, TCP_LISTEN);
+	/* get_port does not return an error code, yet */
+	err = -EADDRINUSE;
 	if (!sk->sk_prot->get_port(sk, inet->inet_num)) {
 		inet->inet_sport = htons(inet->inet_num);
 
@@ -1074,7 +1132,7 @@
 
 	sock_orphan(child);
 
-	percpu_counter_inc(sk->sk_prot->orphan_count);
+	this_cpu_inc(*sk->sk_prot->orphan_count);
 
 	if (sk->sk_protocol == IPPROTO_TCP && tcp_rsk(req)->tfo_listener) {
 		BUG_ON(rcu_access_pointer(tcp_sk(child)->fastopen_rsk) != req);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/inet_diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/inet_diag.c
@@ -57,7 +57,7 @@
 		return ERR_PTR(-ENOENT);
 	}
 
-	if (!inet_diag_table[proto])
+	if (!READ_ONCE(inet_diag_table[proto]))
 		sock_load_diag_module(AF_INET, proto);
 
 	mutex_lock(&inet_diag_table_mutex);
@@ -261,6 +261,7 @@
 	r->idiag_state = sk->sk_state;
 	r->idiag_timer = 0;
 	r->idiag_retrans = 0;
+	r->idiag_expires = 0;
 
 	if (inet_diag_msg_attrs_fill(sk, skb, r, ext,
 				     sk_user_ns(NETLINK_CB(cb->skb).sk),
@@ -314,9 +315,6 @@
 		r->idiag_retrans = icsk->icsk_probes_out;
 		r->idiag_expires =
 			jiffies_delta_to_msecs(sk->sk_timer.expires - jiffies);
-	} else {
-		r->idiag_timer = 0;
-		r->idiag_expires = 0;
 	}
 
 	if ((ext & (1 << (INET_DIAG_INFO - 1))) && handler->idiag_info_size) {
@@ -1030,12 +1028,13 @@
 		if (!(idiag_states & TCPF_LISTEN) || r->id.idiag_dport)
 			goto skip_listen_ht;
 
-		for (i = s_i; i < INET_LHTABLE_SIZE; i++) {
+		for (i = s_i; i <= hashinfo->lhash2_mask; i++) {
 			struct inet_listen_hashbucket *ilb;
 			struct hlist_nulls_node *node;
 
 			num = 0;
-			ilb = &hashinfo->listening_hash[i];
+			ilb = &hashinfo->lhash2[i];
+
 			spin_lock(&ilb->lock);
 			sk_nulls_for_each(sk, node, &ilb->nulls_head) {
 				struct inet_sock *inet = inet_sk(sk);
@@ -1282,6 +1281,7 @@
 	req.sdiag_family = AF_UNSPEC; /* compatibility */
 	req.sdiag_protocol = inet_diag_type2proto(cb->nlh->nlmsg_type);
 	req.idiag_ext = rc->idiag_ext;
+	req.pad = 0;
 	req.idiag_states = rc->idiag_states;
 	req.id = rc->id;
 
@@ -1297,6 +1297,7 @@
 	req.sdiag_family = rc->idiag_family;
 	req.sdiag_protocol = inet_diag_type2proto(nlh->nlmsg_type);
 	req.idiag_ext = rc->idiag_ext;
+	req.pad = 0;
 	req.idiag_states = rc->idiag_states;
 	req.id = rc->id;
 
@@ -1420,7 +1421,7 @@
 	mutex_lock(&inet_diag_table_mutex);
 	err = -EEXIST;
 	if (!inet_diag_table[type]) {
-		inet_diag_table[type] = h;
+		WRITE_ONCE(inet_diag_table[type], h);
 		err = 0;
 	}
 	mutex_unlock(&inet_diag_table_mutex);
@@ -1437,7 +1438,7 @@
 		return;
 
 	mutex_lock(&inet_diag_table_mutex);
-	inet_diag_table[type] = NULL;
+	WRITE_ONCE(inet_diag_table[type], NULL);
 	mutex_unlock(&inet_diag_table_mutex);
 }
 EXPORT_SYMBOL_GPL(inet_diag_unregister);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/inet_fragment.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/inet_fragment.c
@@ -24,6 +24,8 @@
 #include <net/ip.h>
 #include <net/ipv6.h>
 
+#include "../core/sock_destructor.h"
+
 /* Use skb->cb to track consecutive/adjacent fragments coming at
  * the end of the queue. Nodes in the rb-tree queue will
  * contain "runs" of one or more adjacent fragments.
@@ -39,6 +41,7 @@
 	};
 	struct sk_buff		*next_frag;
 	int			frag_run_len;
+	int			ip_defrag_offset;
 };
 
 #define FRAG_CB(skb)		((struct ipfrag_skb_cb *)((skb)->cb))
@@ -235,9 +238,9 @@
 		/* The RCU read lock provides a memory barrier
 		 * guaranteeing that if fqdir->dead is false then
 		 * the hash table destruction will not start until
-		 * after we unlock.  Paired with inet_frags_exit_net().
+		 * after we unlock.  Paired with fqdir_pre_exit().
 		 */
-		if (!fqdir->dead) {
+		if (!READ_ONCE(fqdir->dead)) {
 			rhashtable_remove_fast(&fqdir->rhashtable, &fq->node,
 					       fqdir->f->rhash_params);
 			refcount_dec(&fq->refcnt);
@@ -352,9 +355,11 @@
 /* TODO : call from rcu_read_lock() and no longer use refcount_inc_not_zero() */
 struct inet_frag_queue *inet_frag_find(struct fqdir *fqdir, void *key)
 {
+	/* This pairs with WRITE_ONCE() in fqdir_pre_exit(). */
+	long high_thresh = READ_ONCE(fqdir->high_thresh);
 	struct inet_frag_queue *fq = NULL, *prev;
 
-	if (!fqdir->high_thresh || frag_mem_limit(fqdir) > fqdir->high_thresh)
+	if (!high_thresh || frag_mem_limit(fqdir) > high_thresh)
 		return NULL;
 
 	rcu_read_lock();
@@ -388,12 +393,12 @@
 	 */
 	if (!last)
 		fragrun_create(q, skb);  /* First fragment. */
-	else if (last->ip_defrag_offset + last->len < end) {
+	else if (FRAG_CB(last)->ip_defrag_offset + last->len < end) {
 		/* This is the common case: skb goes to the end. */
 		/* Detect and discard overlaps. */
-		if (offset < last->ip_defrag_offset + last->len)
+		if (offset < FRAG_CB(last)->ip_defrag_offset + last->len)
 			return IPFRAG_OVERLAP;
-		if (offset == last->ip_defrag_offset + last->len)
+		if (offset == FRAG_CB(last)->ip_defrag_offset + last->len)
 			fragrun_append_to_last(q, skb);
 		else
 			fragrun_create(q, skb);
@@ -410,13 +415,13 @@
 
 			parent = *rbn;
 			curr = rb_to_skb(parent);
-			curr_run_end = curr->ip_defrag_offset +
+			curr_run_end = FRAG_CB(curr)->ip_defrag_offset +
 					FRAG_CB(curr)->frag_run_len;
-			if (end <= curr->ip_defrag_offset)
+			if (end <= FRAG_CB(curr)->ip_defrag_offset)
 				rbn = &parent->rb_left;
 			else if (offset >= curr_run_end)
 				rbn = &parent->rb_right;
-			else if (offset >= curr->ip_defrag_offset &&
+			else if (offset >= FRAG_CB(curr)->ip_defrag_offset &&
 				 end <= curr_run_end)
 				return IPFRAG_DUP;
 			else
@@ -430,7 +435,7 @@
 		rb_insert_color(&skb->rbnode, &q->rb_fragments);
 	}
 
-	skb->ip_defrag_offset = offset;
+	FRAG_CB(skb)->ip_defrag_offset = offset;
 
 	return IPFRAG_OK;
 }
@@ -440,13 +445,28 @@
 			      struct sk_buff *parent)
 {
 	struct sk_buff *fp, *head = skb_rb_first(&q->rb_fragments);
-	struct sk_buff **nextp;
+	void (*destructor)(struct sk_buff *);
+	unsigned int orig_truesize = 0;
+	struct sk_buff **nextp = NULL;
+	struct sock *sk = skb->sk;
 	int delta;
 
+	if (sk && is_skb_wmem(skb)) {
+		/* TX: skb->sk might have been passed as argument to
+		 * dst->output and must remain valid until tx completes.
+		 *
+		 * Move sk to reassembled skb and fix up wmem accounting.
+		 */
+		orig_truesize = skb->truesize;
+		destructor = skb->destructor;
+	}
+
 	if (head != skb) {
 		fp = skb_clone(skb, GFP_ATOMIC);
-		if (!fp)
-			return NULL;
+		if (!fp) {
+			head = skb;
+			goto out_restore_sk;
+		}
 		FRAG_CB(fp)->next_frag = FRAG_CB(skb)->next_frag;
 		if (RB_EMPTY_NODE(&skb->rbnode))
 			FRAG_CB(parent)->next_frag = fp;
@@ -455,6 +475,12 @@
 					&q->rb_fragments);
 		if (q->fragments_tail == skb)
 			q->fragments_tail = fp;
+
+		if (orig_truesize) {
+			/* prevent skb_morph from releasing sk */
+			skb->sk = NULL;
+			skb->destructor = NULL;
+		}
 		skb_morph(skb, head);
 		FRAG_CB(skb)->next_frag = FRAG_CB(head)->next_frag;
 		rb_replace_node(&head->rbnode, &skb->rbnode,
@@ -462,13 +488,13 @@
 		consume_skb(head);
 		head = skb;
 	}
-	WARN_ON(head->ip_defrag_offset != 0);
+	WARN_ON(FRAG_CB(head)->ip_defrag_offset != 0);
 
 	delta = -head->truesize;
 
 	/* Head of list must not be cloned. */
 	if (skb_unclone(head, GFP_ATOMIC))
-		return NULL;
+		goto out_restore_sk;
 
 	delta += head->truesize;
 	if (delta)
@@ -484,7 +510,7 @@
 
 		clone = alloc_skb(0, GFP_ATOMIC);
 		if (!clone)
-			return NULL;
+			goto out_restore_sk;
 		skb_shinfo(clone)->frag_list = skb_shinfo(head)->frag_list;
 		skb_frag_list_init(head);
 		for (i = 0; i < skb_shinfo(head)->nr_frags; i++)
@@ -501,6 +527,21 @@
 		nextp = &skb_shinfo(head)->frag_list;
 	}
 
+out_restore_sk:
+	if (orig_truesize) {
+		int ts_delta = head->truesize - orig_truesize;
+
+		/* if this reassembled skb is fragmented later,
+		 * fraglist skbs will get skb->sk assigned from head->sk,
+		 * and each frag skb will be released via sock_wfree.
+		 *
+		 * Update sk_wmem_alloc.
+		 */
+		head->sk = sk;
+		head->destructor = destructor;
+		refcount_add(ts_delta, &sk->sk_wmem_alloc);
+	}
+
 	return nextp;
 }
 EXPORT_SYMBOL(inet_frag_reasm_prepare);
@@ -508,6 +549,8 @@
 void inet_frag_reasm_finish(struct inet_frag_queue *q, struct sk_buff *head,
 			    void *reasm_data, bool try_coalesce)
 {
+	struct sock *sk = is_skb_wmem(head) ? head->sk : NULL;
+	const unsigned int head_truesize = head->truesize;
 	struct sk_buff **nextp = (struct sk_buff **)reasm_data;
 	struct rb_node *rbn;
 	struct sk_buff *fp;
@@ -570,6 +613,9 @@
 	skb_mark_not_on_list(head);
 	head->prev = NULL;
 	head->tstamp = q->stamp;
+
+	if (sk)
+		refcount_add(sum_truesize - head_truesize, &sk->sk_wmem_alloc);
 }
 EXPORT_SYMBOL(inet_frag_reasm_finish);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/inet_hashtables.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/inet_hashtables.c
@@ -28,9 +28,9 @@
 #include <net/tcp.h>
 #include <net/sock_reuseport.h>
 
-static u32 inet_ehashfn(const struct net *net, const __be32 laddr,
-			const __u16 lport, const __be32 faddr,
-			const __be16 fport)
+u32 inet_ehashfn(const struct net *net, const __be32 laddr,
+		 const __u16 lport, const __be32 faddr,
+		 const __be16 fport)
 {
 	static u32 inet_ehash_secret __read_mostly;
 
@@ -39,6 +39,7 @@
 	return __inet_ehashfn(laddr, lport, faddr, fport,
 			      inet_ehash_secret + net_hash_mix(net));
 }
+EXPORT_SYMBOL_GPL(inet_ehashfn);
 
 /* This function handles inet_sock, but also timewait and request sockets
  * for IPv4/IPv6.
@@ -193,42 +194,6 @@
 	return inet_lhash2_bucket(h, hash);
 }
 
-static void inet_hash2(struct inet_hashinfo *h, struct sock *sk)
-{
-	struct inet_listen_hashbucket *ilb2;
-
-	if (!h->lhash2)
-		return;
-
-	ilb2 = inet_lhash2_bucket_sk(h, sk);
-
-	spin_lock(&ilb2->lock);
-	if (sk->sk_reuseport && sk->sk_family == AF_INET6)
-		hlist_add_tail_rcu(&inet_csk(sk)->icsk_listen_portaddr_node,
-				   &ilb2->head);
-	else
-		hlist_add_head_rcu(&inet_csk(sk)->icsk_listen_portaddr_node,
-				   &ilb2->head);
-	ilb2->count++;
-	spin_unlock(&ilb2->lock);
-}
-
-static void inet_unhash2(struct inet_hashinfo *h, struct sock *sk)
-{
-	struct inet_listen_hashbucket *ilb2;
-
-	if (!h->lhash2 ||
-	    WARN_ON_ONCE(hlist_unhashed(&inet_csk(sk)->icsk_listen_portaddr_node)))
-		return;
-
-	ilb2 = inet_lhash2_bucket_sk(h, sk);
-
-	spin_lock(&ilb2->lock);
-	hlist_del_init_rcu(&inet_csk(sk)->icsk_listen_portaddr_node);
-	ilb2->count--;
-	spin_unlock(&ilb2->lock);
-}
-
 static inline int compute_score(struct sock *sk, struct net *net,
 				const unsigned short hnum, const __be32 daddr,
 				const int dif, const int sdif)
@@ -252,20 +217,25 @@
 	return score;
 }
 
-static inline struct sock *lookup_reuseport(struct net *net, struct sock *sk,
-					    struct sk_buff *skb, int doff,
-					    __be32 saddr, __be16 sport,
-					    __be32 daddr, unsigned short hnum)
+INDIRECT_CALLABLE_DECLARE(inet_ehashfn_t udp_ehashfn);
+
+struct sock *inet_lookup_reuseport(struct net *net, struct sock *sk,
+				   struct sk_buff *skb, int doff,
+				   __be32 saddr, __be16 sport,
+				   __be32 daddr, unsigned short hnum,
+				   inet_ehashfn_t *ehashfn)
 {
 	struct sock *reuse_sk = NULL;
 	u32 phash;
 
 	if (sk->sk_reuseport) {
-		phash = inet_ehashfn(net, daddr, hnum, saddr, sport);
+		phash = INDIRECT_CALL_2(ehashfn, udp_ehashfn, inet_ehashfn,
+					net, daddr, hnum, saddr, sport);
 		reuse_sk = reuseport_select_sock(sk, phash, skb, doff);
 	}
 	return reuse_sk;
 }
+EXPORT_SYMBOL_GPL(inet_lookup_reuseport);
 
 /*
  * Here are some nice properties to exploit here. The BSD API
@@ -282,16 +252,15 @@
 				const __be32 daddr, const unsigned short hnum,
 				const int dif, const int sdif)
 {
-	struct inet_connection_sock *icsk;
 	struct sock *sk, *result = NULL;
+	struct hlist_nulls_node *node;
 	int score, hiscore = 0;
 
-	inet_lhash2_for_each_icsk_rcu(icsk, &ilb2->head) {
-		sk = (struct sock *)icsk;
+	sk_nulls_for_each_rcu(sk, node, &ilb2->nulls_head) {
 		score = compute_score(sk, net, hnum, daddr, dif, sdif);
 		if (score > hiscore) {
-			result = lookup_reuseport(net, sk, skb, doff,
-						  saddr, sport, daddr, hnum);
+			result = inet_lookup_reuseport(net, sk, skb, doff,
+						       saddr, sport, daddr, hnum, inet_ehashfn);
 			if (result)
 				return result;
 
@@ -320,7 +289,8 @@
 	if (no_reuseport || IS_ERR_OR_NULL(sk))
 		return sk;
 
-	reuse_sk = lookup_reuseport(net, sk, skb, doff, saddr, sport, daddr, hnum);
+	reuse_sk = inet_lookup_reuseport(net, sk, skb, doff, saddr, sport, daddr, hnum,
+					 inet_ehashfn);
 	if (reuse_sk)
 		sk = reuse_sk;
 	return sk;
@@ -410,13 +380,11 @@
 	sk_nulls_for_each_rcu(sk, node, &head->chain) {
 		if (sk->sk_hash != hash)
 			continue;
-		if (likely(INET_MATCH(sk, net, acookie,
-				      saddr, daddr, ports, dif, sdif))) {
+		if (likely(INET_MATCH(net, sk, acookie, ports, dif, sdif))) {
 			if (unlikely(!refcount_inc_not_zero(&sk->sk_refcnt)))
 				goto out;
-			if (unlikely(!INET_MATCH(sk, net, acookie,
-						 saddr, daddr, ports,
-						 dif, sdif))) {
+			if (unlikely(!INET_MATCH(net, sk, acookie,
+						 ports, dif, sdif))) {
 				sock_gen_put(sk);
 				goto begin;
 			}
@@ -465,8 +433,7 @@
 		if (sk2->sk_hash != hash)
 			continue;
 
-		if (likely(INET_MATCH(sk2, net, acookie,
-					 saddr, daddr, ports, dif, sdif))) {
+		if (likely(INET_MATCH(net, sk2, acookie, ports, dif, sdif))) {
 			if (sk2->sk_state == TCP_TIME_WAIT) {
 				tw = inet_twsk(sk2);
 				if (twsk_unique(sk, sk2, twp))
@@ -504,7 +471,7 @@
 	return -EADDRNOTAVAIL;
 }
 
-static u32 inet_sk_port_offset(const struct sock *sk)
+static u64 inet_sk_port_offset(const struct sock *sk)
 {
 	const struct inet_sock *inet = inet_sk(sk);
 
@@ -532,16 +499,14 @@
 		if (esk->sk_hash != sk->sk_hash)
 			continue;
 		if (sk->sk_family == AF_INET) {
-			if (unlikely(INET_MATCH(esk, net, acookie,
-						sk->sk_daddr,
-						sk->sk_rcv_saddr,
+			if (unlikely(INET_MATCH(net, esk, acookie,
 						ports, dif, sdif))) {
 				return true;
 			}
 		}
 #if IS_ENABLED(CONFIG_IPV6)
 		else if (sk->sk_family == AF_INET6) {
-			if (unlikely(INET6_MATCH(esk, net,
+			if (unlikely(inet6_match(net, esk,
 						 &sk->sk_v6_daddr,
 						 &sk->sk_v6_rcv_saddr,
 						 ports, dif, sdif))) {
@@ -598,7 +563,7 @@
 	if (ok) {
 		sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 	} else {
-		percpu_counter_inc(sk->sk_prot->orphan_count);
+		this_cpu_inc(*sk->sk_prot->orphan_count);
 		inet_sk_set_state(sk, TCP_CLOSE);
 		sock_set_flag(sk, SOCK_DEAD);
 		inet_csk_destroy_sock(sk);
@@ -633,33 +598,33 @@
 int __inet_hash(struct sock *sk, struct sock *osk)
 {
 	struct inet_hashinfo *hashinfo = sk->sk_prot->h.hashinfo;
-	struct inet_listen_hashbucket *ilb;
+	struct inet_listen_hashbucket *ilb2;
 	int err = 0;
 
 	if (sk->sk_state != TCP_LISTEN) {
+		local_bh_disable();
 		inet_ehash_nolisten(sk, osk, NULL);
+		local_bh_enable();
 		return 0;
 	}
 	WARN_ON(!sk_unhashed(sk));
-	ilb = &hashinfo->listening_hash[inet_sk_listen_hashfn(sk)];
+	ilb2 = inet_lhash2_bucket_sk(hashinfo, sk);
 
-	spin_lock(&ilb->lock);
+	spin_lock(&ilb2->lock);
 	if (sk->sk_reuseport) {
-		err = inet_reuseport_add_sock(sk, ilb);
+		err = inet_reuseport_add_sock(sk, ilb2);
 		if (err)
 			goto unlock;
 	}
+	sock_set_flag(sk, SOCK_RCU_FREE);
 	if (IS_ENABLED(CONFIG_IPV6) && sk->sk_reuseport &&
 		sk->sk_family == AF_INET6)
-		__sk_nulls_add_node_tail_rcu(sk, &ilb->nulls_head);
+		__sk_nulls_add_node_tail_rcu(sk, &ilb2->nulls_head);
 	else
-		__sk_nulls_add_node_rcu(sk, &ilb->nulls_head);
-	inet_hash2(hashinfo, sk);
-	ilb->count++;
-	sock_set_flag(sk, SOCK_RCU_FREE);
+		__sk_nulls_add_node_rcu(sk, &ilb2->nulls_head);
 	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 unlock:
-	spin_unlock(&ilb->lock);
+	spin_unlock(&ilb2->lock);
 
 	return err;
 }
@@ -669,11 +634,8 @@
 {
 	int err = 0;
 
-	if (sk->sk_state != TCP_CLOSE) {
-		local_bh_disable();
+	if (sk->sk_state != TCP_CLOSE)
 		err = __inet_hash(sk, NULL);
-		local_bh_enable();
-	}
 
 	return err;
 }
@@ -682,32 +644,41 @@
 void inet_unhash(struct sock *sk)
 {
 	struct inet_hashinfo *hashinfo = sk->sk_prot->h.hashinfo;
-	struct inet_listen_hashbucket *ilb = NULL;
-	spinlock_t *lock;
 
 	if (sk_unhashed(sk))
 		return;
 
 	if (sk->sk_state == TCP_LISTEN) {
-		ilb = &hashinfo->listening_hash[inet_sk_listen_hashfn(sk)];
-		lock = &ilb->lock;
+		struct inet_listen_hashbucket *ilb2;
+
+		ilb2 = inet_lhash2_bucket_sk(hashinfo, sk);
+		/* Don't disable bottom halves while acquiring the lock to
+		 * avoid circular locking dependency on PREEMPT_RT.
+		 */
+		spin_lock(&ilb2->lock);
+		if (sk_unhashed(sk)) {
+			spin_unlock(&ilb2->lock);
+			return;
+		}
+
+		if (rcu_access_pointer(sk->sk_reuseport_cb))
+			reuseport_stop_listen_sock(sk);
+
+		__sk_nulls_del_node_init_rcu(sk);
+		sock_prot_inuse_add(sock_net(sk), sk->sk_prot, -1);
+		spin_unlock(&ilb2->lock);
 	} else {
-		lock = inet_ehash_lockp(hashinfo, sk->sk_hash);
-	}
-	spin_lock_bh(lock);
-	if (sk_unhashed(sk))
-		goto unlock;
+		spinlock_t *lock = inet_ehash_lockp(hashinfo, sk->sk_hash);
 
-	if (rcu_access_pointer(sk->sk_reuseport_cb))
-		reuseport_stop_listen_sock(sk);
-	if (ilb) {
-		inet_unhash2(hashinfo, sk);
-		ilb->count--;
+		spin_lock_bh(lock);
+		if (sk_unhashed(sk)) {
+			spin_unlock_bh(lock);
+			return;
+		}
+		__sk_nulls_del_node_init_rcu(sk);
+		sock_prot_inuse_add(sock_net(sk), sk->sk_prot, -1);
+		spin_unlock_bh(lock);
 	}
-	__sk_nulls_del_node_init_rcu(sk);
-	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, -1);
-unlock:
-	spin_unlock_bh(lock);
 }
 EXPORT_SYMBOL_GPL(inet_unhash);
 
@@ -715,15 +686,17 @@
  * Note that we use 32bit integers (vs RFC 'short integers')
  * because 2^16 is not a multiple of num_ephemeral and this
  * property might be used by clever attacker.
- * RFC claims using TABLE_LENGTH=10 buckets gives an improvement,
- * we use 256 instead to really give more isolation and
- * privacy, this only consumes 1 KB of kernel memory.
+ *
+ * RFC claims using TABLE_LENGTH=10 buckets gives an improvement, though
+ * attacks were since demonstrated, thus we use 65536 by default instead
+ * to really give more isolation and privacy, at the expense of 256kB
+ * of kernel memory.
  */
-#define INET_TABLE_PERTURB_SHIFT 8
-static u32 table_perturb[1 << INET_TABLE_PERTURB_SHIFT];
+#define INET_TABLE_PERTURB_SIZE (1 << CONFIG_INET_TABLE_PERTURB_ORDER)
+static u32 *table_perturb;
 
 int __inet_hash_connect(struct inet_timewait_death_row *death_row,
-		struct sock *sk, u32 port_offset,
+		struct sock *sk, u64 port_offset,
 		int (*check_established)(struct inet_timewait_death_row *,
 			struct sock *, __u16, struct inet_timewait_sock **))
 {
@@ -739,17 +712,7 @@
 	u32 index;
 
 	if (port) {
-		head = &hinfo->bhash[inet_bhashfn(net, port,
-						  hinfo->bhash_size)];
-		tb = inet_csk(sk)->icsk_bind_hash;
-		spin_lock_bh(&head->lock);
-		if (sk_head(&tb->owners) == sk && !sk->sk_bind_node.next) {
-			inet_ehash_nolisten(sk, NULL, NULL);
-			spin_unlock_bh(&head->lock);
-			return 0;
-		}
-		spin_unlock(&head->lock);
-		/* No definite answer... Walk to established hash table */
+		local_bh_disable();
 		ret = check_established(death_row, sk, port, NULL);
 		local_bh_enable();
 		return ret;
@@ -763,10 +726,13 @@
 	if (likely(remaining > 1))
 		remaining &= ~1U;
 
-	net_get_random_once(table_perturb, sizeof(table_perturb));
-	index = hash_32(port_offset, INET_TABLE_PERTURB_SHIFT);
+	get_random_slow_once(table_perturb,
+			     INET_TABLE_PERTURB_SIZE * sizeof(*table_perturb));
+	index = port_offset & (INET_TABLE_PERTURB_SIZE - 1);
+
+	offset = READ_ONCE(table_perturb[index]) + (port_offset >> 32);
+	offset %= remaining;
 
-	offset = (READ_ONCE(table_perturb[index]) + port_offset) % remaining;
 	/* In first pass we try ports of @low parity.
 	 * inet_csk_get_port() does the opposite choice.
 	 */
@@ -820,11 +786,12 @@
 	return -EADDRNOTAVAIL;
 
 ok:
-	/* If our first attempt found a candidate, skip next candidate
-	 * in 1/16 of cases to add some noise.
+	/* Here we want to add a little bit of randomness to the next source
+	 * port that will be chosen. We use a max() with a random here so that
+	 * on low contention the randomness is maximal and on high contention
+	 * it may be inexistent.
 	 */
-	if (!i && !(prandom_u32() % 16))
-		i = 2;
+	i = max_t(int, i, (prandom_u32() & 7) * 2);
 	WRITE_ONCE(table_perturb[index], READ_ONCE(table_perturb[index]) + i + 2);
 
 	/* Head lock still held and bh's disabled */
@@ -848,7 +815,7 @@
 int inet_hash_connect(struct inet_timewait_death_row *death_row,
 		      struct sock *sk)
 {
-	u32 port_offset = 0;
+	u64 port_offset = 0;
 
 	if (!inet_sk(sk)->inet_num)
 		port_offset = inet_sk_port_offset(sk);
@@ -857,29 +824,14 @@
 }
 EXPORT_SYMBOL_GPL(inet_hash_connect);
 
-void inet_hashinfo_init(struct inet_hashinfo *h)
-{
-	int i;
-
-	for (i = 0; i < INET_LHTABLE_SIZE; i++) {
-		spin_lock_init(&h->listening_hash[i].lock);
-		INIT_HLIST_NULLS_HEAD(&h->listening_hash[i].nulls_head,
-				      i + LISTENING_NULLS_BASE);
-		h->listening_hash[i].count = 0;
-	}
-
-	h->lhash2 = NULL;
-}
-EXPORT_SYMBOL_GPL(inet_hashinfo_init);
-
 static void init_hashinfo_lhash2(struct inet_hashinfo *h)
 {
 	int i;
 
 	for (i = 0; i <= h->lhash2_mask; i++) {
 		spin_lock_init(&h->lhash2[i].lock);
-		INIT_HLIST_HEAD(&h->lhash2[i].head);
-		h->lhash2[i].count = 0;
+		INIT_HLIST_NULLS_HEAD(&h->lhash2[i].nulls_head,
+				      i + LISTENING_NULLS_BASE);
 	}
 }
 
@@ -898,6 +850,14 @@
 					    low_limit,
 					    high_limit);
 	init_hashinfo_lhash2(h);
+
+	/* this one is used for source ports of outgoing connections */
+	table_perturb = alloc_large_system_hash("Table-perturb",
+						sizeof(*table_perturb),
+						INET_TABLE_PERTURB_SIZE,
+						0, 0, NULL, NULL,
+						INET_TABLE_PERTURB_SIZE,
+						INET_TABLE_PERTURB_SIZE);
 }
 
 int inet_hashinfo2_init_mod(struct inet_hashinfo *h)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/inet_timewait_sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/inet_timewait_sock.c
@@ -254,12 +254,12 @@
 }
 EXPORT_SYMBOL_GPL(__inet_twsk_schedule);
 
+/* Remove all non full sockets (TIME_WAIT and NEW_SYN_RECV) for dead netns */
 void inet_twsk_purge(struct inet_hashinfo *hashinfo, int family)
 {
-	struct inet_timewait_sock *tw;
-	struct sock *sk;
 	struct hlist_nulls_node *node;
 	unsigned int slot;
+	struct sock *sk;
 
 	for (slot = 0; slot <= hashinfo->ehash_mask; slot++) {
 		struct inet_ehash_bucket *head = &hashinfo->ehash[slot];
@@ -268,25 +268,35 @@
 		rcu_read_lock();
 restart:
 		sk_nulls_for_each_rcu(sk, node, &head->chain) {
-			if (sk->sk_state != TCP_TIME_WAIT)
+			int state = inet_sk_state_load(sk);
+
+			if ((1 << state) & ~(TCPF_TIME_WAIT |
+					     TCPF_NEW_SYN_RECV))
 				continue;
-			tw = inet_twsk(sk);
-			if ((tw->tw_family != family) ||
-				refcount_read(&twsk_net(tw)->ns.count))
+
+			if (sk->sk_family != family ||
+			    refcount_read(&sock_net(sk)->ns.count))
 				continue;
 
-			if (unlikely(!refcount_inc_not_zero(&tw->tw_refcnt)))
+			if (unlikely(!refcount_inc_not_zero(&sk->sk_refcnt)))
 				continue;
 
-			if (unlikely((tw->tw_family != family) ||
-				     refcount_read(&twsk_net(tw)->ns.count))) {
-				inet_twsk_put(tw);
+			if (unlikely(sk->sk_family != family ||
+				     refcount_read(&sock_net(sk)->ns.count))) {
+				sock_gen_put(sk);
 				goto restart;
 			}
 
 			rcu_read_unlock();
 			local_bh_disable();
-			inet_twsk_deschedule_put(tw);
+			if (state == TCP_TIME_WAIT) {
+				inet_twsk_deschedule_put(inet_twsk(sk));
+			} else {
+				struct request_sock *req = inet_reqsk(sk);
+
+				inet_csk_reqsk_queue_drop_and_put(req->rsk_listener,
+								  req);
+			}
 			local_bh_enable();
 			goto restart_rcu;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/inetpeer.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/inetpeer.c
@@ -141,16 +141,20 @@
 			 struct inet_peer *gc_stack[],
 			 unsigned int gc_cnt)
 {
+	int peer_threshold, peer_maxttl, peer_minttl;
 	struct inet_peer *p;
 	__u32 delta, ttl;
 	int i;
 
-	if (base->total >= inet_peer_threshold)
+	peer_threshold = READ_ONCE(inet_peer_threshold);
+	peer_maxttl = READ_ONCE(inet_peer_maxttl);
+	peer_minttl = READ_ONCE(inet_peer_minttl);
+
+	if (base->total >= peer_threshold)
 		ttl = 0; /* be aggressive */
 	else
-		ttl = inet_peer_maxttl
-				- (inet_peer_maxttl - inet_peer_minttl) / HZ *
-					base->total / inet_peer_threshold * HZ;
+		ttl = peer_maxttl - (peer_maxttl - peer_minttl) / HZ *
+			base->total / peer_threshold * HZ;
 	for (i = 0; i < gc_cnt; i++) {
 		p = gc_stack[i];
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_forward.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_forward.c
@@ -151,7 +151,7 @@
 	    !skb_sec_path(skb))
 		ip_rt_send_redirect(skb);
 
-	if (net->ipv4.sysctl_ip_fwd_update_priority)
+	if (READ_ONCE(net->ipv4.sysctl_ip_fwd_update_priority))
 		skb->priority = rt_tos2priority(iph->tos);
 
 	return NF_HOOK(NFPROTO_IPV4, NF_INET_FORWARD,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_fragment.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_fragment.c
@@ -144,7 +144,8 @@
 
 	rcu_read_lock();
 
-	if (qp->q.fqdir->dead)
+	/* Paired with WRITE_ONCE() in fqdir_pre_exit(). */
+	if (READ_ONCE(qp->q.fqdir->dead))
 		goto out_rcu_unlock;
 
 	spin_lock(&qp->q.lock);
@@ -376,6 +377,7 @@
 	}
 
 	skb_dst_drop(skb);
+	skb_orphan(skb);
 	return -EINPROGRESS;
 
 insert_error:
@@ -478,7 +480,6 @@
 	struct ipq *qp;
 
 	__IP_INC_STATS(net, IPSTATS_MIB_REASMREQDS);
-	skb_orphan(skb);
 
 	/* Lookup (or create) queue header */
 	qp = ip_find(net, ip_hdr(skb), user, vif);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_gre.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_gre.c
@@ -280,8 +280,13 @@
 					  tpi->flags | TUNNEL_NO_KEY,
 					  iph->saddr, iph->daddr, 0);
 	} else {
+		if (unlikely(!pskb_may_pull(skb,
+					    gre_hdr_len + sizeof(*ershdr))))
+			return PACKET_REJECT;
+
 		ershdr = (struct erspan_base_hdr *)(skb->data + gre_hdr_len);
 		ver = ershdr->ver;
+		iph = ip_hdr(skb);
 		tunnel = ip_tunnel_lookup(itn, skb->dev->ifindex,
 					  tpi->flags | TUNNEL_KEY,
 					  iph->saddr, iph->daddr, tpi->key);
@@ -459,14 +464,12 @@
 		       __be16 proto)
 {
 	struct ip_tunnel *tunnel = netdev_priv(dev);
-
-	if (tunnel->parms.o_flags & TUNNEL_SEQ)
-		tunnel->o_seqno++;
+	__be16 flags = tunnel->parms.o_flags;
 
 	/* Push GRE header. */
 	gre_build_header(skb, tunnel->tun_hlen,
-			 tunnel->parms.o_flags, proto, tunnel->parms.o_key,
-			 htonl(tunnel->o_seqno));
+			 flags, proto, tunnel->parms.o_key,
+			 (flags & TUNNEL_SEQ) ? htonl(atomic_fetch_inc(&tunnel->o_seqno)) : 0);
 
 	ip_tunnel_xmit(skb, dev, tnl_params, tnl_params->protocol);
 }
@@ -504,7 +507,7 @@
 		(TUNNEL_CSUM | TUNNEL_KEY | TUNNEL_SEQ);
 	gre_build_header(skb, tunnel_hlen, flags, proto,
 			 tunnel_id_to_key32(tun_info->key.tun_id),
-			 (flags & TUNNEL_SEQ) ? htonl(tunnel->o_seqno++) : 0);
+			 (flags & TUNNEL_SEQ) ? htonl(atomic_fetch_inc(&tunnel->o_seqno)) : 0);
 
 	ip_md_tunnel_xmit(skb, dev, IPPROTO_GRE, tunnel_hlen);
 
@@ -526,7 +529,6 @@
 	int tunnel_hlen;
 	int version;
 	int nhoff;
-	int thoff;
 
 	tun_info = skb_tunnel_info(skb);
 	if (unlikely(!tun_info || !(tun_info->mode & IP_TUNNEL_INFO_TX) ||
@@ -555,15 +557,21 @@
 		truncate = true;
 	}
 
-	nhoff = skb_network_header(skb) - skb_mac_header(skb);
+	nhoff = skb_network_offset(skb);
 	if (skb->protocol == htons(ETH_P_IP) &&
 	    (ntohs(ip_hdr(skb)->tot_len) > skb->len - nhoff))
 		truncate = true;
 
-	thoff = skb_transport_header(skb) - skb_mac_header(skb);
-	if (skb->protocol == htons(ETH_P_IPV6) &&
-	    (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff))
-		truncate = true;
+	if (skb->protocol == htons(ETH_P_IPV6)) {
+		int thoff;
+
+		if (skb_transport_header_was_set(skb))
+			thoff = skb_transport_offset(skb);
+		else
+			thoff = nhoff + sizeof(struct ipv6hdr);
+		if (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff)
+			truncate = true;
+	}
 
 	if (version == 1) {
 		erspan_build_header(skb, ntohl(tunnel_id_to_key32(key->tun_id)),
@@ -581,7 +589,7 @@
 	}
 
 	gre_build_header(skb, 8, TUNNEL_SEQ,
-			 proto, 0, htonl(tunnel->o_seqno++));
+			 proto, 0, htonl(atomic_fetch_inc(&tunnel->o_seqno)));
 
 	ip_md_tunnel_xmit(skb, dev, IPPROTO_GRE, tunnel_hlen);
 
@@ -604,7 +612,8 @@
 
 	key = &info->key;
 	ip_tunnel_init_flow(&fl4, IPPROTO_GRE, key->u.ipv4.dst, key->u.ipv4.src,
-			    tunnel_id_to_key32(key->tun_id), key->tos, 0,
+			    tunnel_id_to_key32(key->tun_id),
+			    key->tos & ~INET_ECN_MASK, dev_net(dev), 0,
 			    skb->mark, skb_get_hash(skb));
 	rt = ip_route_output_key(dev_net(dev), &fl4);
 	if (IS_ERR(rt))
@@ -630,21 +639,23 @@
 	}
 
 	if (dev->header_ops) {
-		const int pull_len = tunnel->hlen + sizeof(struct iphdr);
+		int pull_len = tunnel->hlen + sizeof(struct iphdr);
 
 		if (skb_cow_head(skb, 0))
 			goto free_skb;
 
-		tnl_params = (const struct iphdr *)skb->data;
-
-		if (pull_len > skb_transport_offset(skb))
+		if (!pskb_may_pull(skb, pull_len))
 			goto free_skb;
 
-		/* Pull skb since ip_tunnel_xmit() needs skb->data pointing
-		 * to gre header.
-		 */
+		tnl_params = (const struct iphdr *)skb->data;
+
+		/* ip_tunnel_xmit() needs skb->data pointing to gre header. */
 		skb_pull(skb, pull_len);
 		skb_reset_mac_header(skb);
+
+		if (skb->ip_summed == CHECKSUM_PARTIAL &&
+		    skb_checksum_start(skb) < skb->data)
+			goto free_skb;
 	} else {
 		if (skb_cow_head(skb, dev->needed_headroom))
 			goto free_skb;
@@ -1495,24 +1506,6 @@
 	struct ip_tunnel_parm *p = &t->parms;
 	__be16 o_flags = p->o_flags;
 
-	if (t->erspan_ver <= 2) {
-		if (t->erspan_ver != 0 && !t->collect_md)
-			o_flags |= TUNNEL_KEY;
-
-		if (nla_put_u8(skb, IFLA_GRE_ERSPAN_VER, t->erspan_ver))
-			goto nla_put_failure;
-
-		if (t->erspan_ver == 1) {
-			if (nla_put_u32(skb, IFLA_GRE_ERSPAN_INDEX, t->index))
-				goto nla_put_failure;
-		} else if (t->erspan_ver == 2) {
-			if (nla_put_u8(skb, IFLA_GRE_ERSPAN_DIR, t->dir))
-				goto nla_put_failure;
-			if (nla_put_u16(skb, IFLA_GRE_ERSPAN_HWID, t->hwid))
-				goto nla_put_failure;
-		}
-	}
-
 	if (nla_put_u32(skb, IFLA_GRE_LINK, p->link) ||
 	    nla_put_be16(skb, IFLA_GRE_IFLAGS,
 			 gre_tnl_flags_to_gre_flags(p->i_flags)) ||
@@ -1553,6 +1546,34 @@
 	return -EMSGSIZE;
 }
 
+static int erspan_fill_info(struct sk_buff *skb, const struct net_device *dev)
+{
+	struct ip_tunnel *t = netdev_priv(dev);
+
+	if (t->erspan_ver <= 2) {
+		if (t->erspan_ver != 0 && !t->collect_md)
+			t->parms.o_flags |= TUNNEL_KEY;
+
+		if (nla_put_u8(skb, IFLA_GRE_ERSPAN_VER, t->erspan_ver))
+			goto nla_put_failure;
+
+		if (t->erspan_ver == 1) {
+			if (nla_put_u32(skb, IFLA_GRE_ERSPAN_INDEX, t->index))
+				goto nla_put_failure;
+		} else if (t->erspan_ver == 2) {
+			if (nla_put_u8(skb, IFLA_GRE_ERSPAN_DIR, t->dir))
+				goto nla_put_failure;
+			if (nla_put_u16(skb, IFLA_GRE_ERSPAN_HWID, t->hwid))
+				goto nla_put_failure;
+		}
+	}
+
+	return ipgre_fill_info(skb, dev);
+
+nla_put_failure:
+	return -EMSGSIZE;
+}
+
 static void erspan_setup(struct net_device *dev)
 {
 	struct ip_tunnel *t = netdev_priv(dev);
@@ -1631,7 +1652,7 @@
 	.changelink	= erspan_changelink,
 	.dellink	= ip_tunnel_dellink,
 	.get_size	= ipgre_get_size,
-	.fill_info	= ipgre_fill_info,
+	.fill_info	= erspan_fill_info,
 	.get_link_net	= ip_tunnel_get_link_net,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_input.c
@@ -310,16 +310,17 @@
 	       ip_hdr(hint)->tos == iph->tos;
 }
 
-INDIRECT_CALLABLE_DECLARE(int udp_v4_early_demux(struct sk_buff *));
-INDIRECT_CALLABLE_DECLARE(int tcp_v4_early_demux(struct sk_buff *));
+int tcp_v4_early_demux(struct sk_buff *skb);
+int udp_v4_early_demux(struct sk_buff *skb);
 static int ip_rcv_finish_core(struct net *net, struct sock *sk,
 			      struct sk_buff *skb, struct net_device *dev,
 			      const struct sk_buff *hint)
 {
 	const struct iphdr *iph = ip_hdr(skb);
-	int (*edemux)(struct sk_buff *skb);
+	int err, drop_reason;
 	struct rtable *rt;
-	int err;
+
+	drop_reason = SKB_DROP_REASON_NOT_SPECIFIED;
 
 	if (ip_can_use_hint(skb, iph, hint)) {
 		err = ip_route_use_hint(skb, iph->daddr, iph->saddr, iph->tos,
@@ -328,21 +329,29 @@
 			goto drop_error;
 	}
 
-	if (net->ipv4.sysctl_ip_early_demux &&
+	if (READ_ONCE(net->ipv4.sysctl_ip_early_demux) &&
 	    !skb_dst(skb) &&
 	    !skb->sk &&
 	    !ip_is_fragment(iph)) {
-		const struct net_protocol *ipprot;
-		int protocol = iph->protocol;
-
-		ipprot = rcu_dereference(inet_protos[protocol]);
-		if (ipprot && (edemux = READ_ONCE(ipprot->early_demux))) {
-			err = INDIRECT_CALL_2(edemux, tcp_v4_early_demux,
-					      udp_v4_early_demux, skb);
-			if (unlikely(err))
-				goto drop_error;
-			/* must reload iph, skb->head might have changed */
-			iph = ip_hdr(skb);
+		switch (iph->protocol) {
+		case IPPROTO_TCP:
+			if (READ_ONCE(net->ipv4.sysctl_tcp_early_demux)) {
+				tcp_v4_early_demux(skb);
+
+				/* must reload iph, skb->head might have changed */
+				iph = ip_hdr(skb);
+			}
+			break;
+		case IPPROTO_UDP:
+			if (READ_ONCE(net->ipv4.sysctl_udp_early_demux)) {
+				err = udp_v4_early_demux(skb);
+				if (unlikely(err))
+					goto drop_error;
+
+				/* must reload iph, skb->head might have changed */
+				iph = ip_hdr(skb);
+			}
+			break;
 		}
 	}
 
@@ -355,6 +364,11 @@
 					   iph->tos, dev);
 		if (unlikely(err))
 			goto drop_error;
+	} else {
+		struct in_device *in_dev = __in_dev_get_rcu(dev);
+
+		if (in_dev && IN_DEV_ORCONF(in_dev, NOPOLICY))
+			IPCB(skb)->flags |= IPSKB_NOPOLICY;
 	}
 
 #ifdef CONFIG_IP_ROUTE_CLASSID
@@ -396,19 +410,23 @@
 		 * so-called "hole-196" attack) so do it for both.
 		 */
 		if (in_dev &&
-		    IN_DEV_ORCONF(in_dev, DROP_UNICAST_IN_L2_MULTICAST))
+		    IN_DEV_ORCONF(in_dev, DROP_UNICAST_IN_L2_MULTICAST)) {
+			drop_reason = SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST;
 			goto drop;
+		}
 	}
 
 	return NET_RX_SUCCESS;
 
 drop:
-	kfree_skb(skb);
+	kfree_skb_reason(skb, drop_reason);
 	return NET_RX_DROP;
 
 drop_error:
-	if (err == -EXDEV)
+	if (err == -EXDEV) {
+		drop_reason = SKB_DROP_REASON_IP_RPFILTER;
 		__NET_INC_STATS(net, LINUX_MIB_IPRPFILTER);
+	}
 	goto drop;
 }
 
@@ -436,13 +454,16 @@
 static struct sk_buff *ip_rcv_core(struct sk_buff *skb, struct net *net)
 {
 	const struct iphdr *iph;
+	int drop_reason;
 	u32 len;
 
 	/* When the interface is in promisc. mode, drop all the crap
 	 * that it receives, do not try to analyse it.
 	 */
-	if (skb->pkt_type == PACKET_OTHERHOST)
+	if (skb->pkt_type == PACKET_OTHERHOST) {
+		drop_reason = SKB_DROP_REASON_OTHERHOST;
 		goto drop;
+	}
 
 	__IP_UPD_PO_STATS(net, IPSTATS_MIB_IN, skb->len);
 
@@ -452,6 +473,7 @@
 		goto out;
 	}
 
+	drop_reason = SKB_DROP_REASON_NOT_SPECIFIED;
 	if (!pskb_may_pull(skb, sizeof(struct iphdr)))
 		goto inhdr_error;
 
@@ -488,6 +510,7 @@
 
 	len = ntohs(iph->tot_len);
 	if (skb->len < len) {
+		drop_reason = SKB_DROP_REASON_PKT_TOO_SMALL;
 		__IP_INC_STATS(net, IPSTATS_MIB_INTRUNCATEDPKTS);
 		goto drop;
 	} else if (len < (iph->ihl*4))
@@ -516,11 +539,14 @@
 	return skb;
 
 csum_error:
+	drop_reason = SKB_DROP_REASON_IP_CSUM;
 	__IP_INC_STATS(net, IPSTATS_MIB_CSUMERRORS);
 inhdr_error:
+	if (drop_reason == SKB_DROP_REASON_NOT_SPECIFIED)
+		drop_reason = SKB_DROP_REASON_IP_INHDR;
 	__IP_INC_STATS(net, IPSTATS_MIB_INHDRERRORS);
 drop:
-	kfree_skb(skb);
+	kfree_skb_reason(skb, drop_reason);
 out:
 	return NULL;
 }
@@ -555,7 +581,8 @@
 static struct sk_buff *ip_extract_route_hint(const struct net *net,
 					     struct sk_buff *skb, int rt_type)
 {
-	if (fib4_has_custom_rules(net) || rt_type == RTN_BROADCAST)
+	if (fib4_has_custom_rules(net) || rt_type == RTN_BROADCAST ||
+	    IPCB(skb)->flags & IPSKB_MULTIPATH)
 		return NULL;
 
 	return skb;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_output.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_output.c
@@ -162,12 +162,19 @@
 	iph->daddr    = (opt && opt->opt.srr ? opt->opt.faddr : daddr);
 	iph->saddr    = saddr;
 	iph->protocol = sk->sk_protocol;
-	if (ip_dont_fragment(sk, &rt->dst)) {
+	/* Do not bother generating IPID for small packets (eg SYNACK) */
+	if (skb->len <= IPV4_MIN_MTU || ip_dont_fragment(sk, &rt->dst)) {
 		iph->frag_off = htons(IP_DF);
 		iph->id = 0;
 	} else {
 		iph->frag_off = 0;
-		__ip_select_ident(net, iph, 1);
+		/* TCP packets here are SYNACK with fat IPv4/TCP options.
+		 * Avoid using the hashed IP ident generator.
+		 */
+		if (sk->sk_protocol == IPPROTO_TCP)
+			iph->id = (__force __be16)prandom_u32();
+		else
+			__ip_select_ident(net, iph, 1);
 	}
 
 	if (opt && opt->opt.optlen) {
@@ -207,7 +214,7 @@
 	if (lwtunnel_xmit_redirect(dst->lwtstate)) {
 		int res = lwtunnel_xmit(skb);
 
-		if (res < 0 || res == LWTUNNEL_XMIT_DONE)
+		if (res != LWTUNNEL_XMIT_CONTINUE)
 			return res;
 	}
 
@@ -826,15 +833,24 @@
 		/* Everything is OK. Generate! */
 		ip_fraglist_init(skb, iph, hlen, &iter);
 
-		if (iter.frag)
-			ip_options_fragment(iter.frag);
-
 		for (;;) {
 			/* Prepare header of the next frame,
 			 * before previous one went down. */
 			if (iter.frag) {
+				bool first_frag = (iter.offset == 0);
+
 				IPCB(iter.frag)->flags = IPCB(skb)->flags;
 				ip_fraglist_prepare(skb, &iter);
+				if (first_frag && IPCB(skb)->opt.optlen) {
+					/* ipcb->opt is not populated for frags
+					 * coming from __ip_make_skb(),
+					 * ip_options_fragment() needs optlen
+					 */
+					IPCB(iter.frag)->opt.optlen =
+						IPCB(skb)->opt.optlen;
+					ip_options_fragment(iter.frag);
+					ip_send_check(iter.iph);
+				}
 			}
 
 			skb->tstamp = tstamp;
@@ -974,9 +990,9 @@
 	mtu = cork->gso_size ? IP_MAX_MTU : cork->fragsize;
 	paged = !!cork->gso_size;
 
-	if (cork->tx_flags & SKBTX_ANY_SW_TSTAMP &&
+	if (cork->tx_flags & SKBTX_ANY_TSTAMP &&
 	    sk->sk_tsflags & SOF_TIMESTAMPING_OPT_ID)
-		tskey = sk->sk_tskey++;
+		tskey = atomic_inc_return(&sk->sk_tskey) - 1;
 
 	hh_len = LL_RESERVED_SPACE(rt->dst.dev);
 
@@ -1235,6 +1251,12 @@
 	if (unlikely(!rt))
 		return -EFAULT;
 
+	cork->fragsize = ip_sk_use_pmtu(sk) ?
+			 dst_mtu(&rt->dst) : READ_ONCE(rt->dst.dev->mtu);
+
+	if (!inetdev_valid_mtu(cork->fragsize))
+		return -ENETUNREACH;
+
 	/*
 	 * setup for corking.
 	 */
@@ -1251,12 +1273,6 @@
 		cork->addr = ipc->addr;
 	}
 
-	cork->fragsize = ip_sk_use_pmtu(sk) ?
-			 dst_mtu(&rt->dst) : READ_ONCE(rt->dst.dev->mtu);
-
-	if (!inetdev_valid_mtu(cork->fragsize))
-		return -ENETUNREACH;
-
 	cork->gso_size = ipc->gso_size;
 
 	cork->dst = &rt->dst;
@@ -1539,9 +1555,19 @@
 	cork->dst = NULL;
 	skb_dst_set(skb, &rt->dst);
 
-	if (iph->protocol == IPPROTO_ICMP)
-		icmp_out_count(net, ((struct icmphdr *)
-			skb_transport_header(skb))->type);
+	if (iph->protocol == IPPROTO_ICMP) {
+		u8 icmp_type;
+
+		/* For such sockets, transhdrlen is zero when do ip_append_data(),
+		 * so icmphdr does not in skb linear region and can not get icmp_type
+		 * by icmp_hdr(skb)->type.
+		 */
+		if (sk->sk_type == SOCK_RAW && !inet_sk(sk)->hdrincl)
+			icmp_type = fl4->fl4_icmp_type;
+		else
+			icmp_type = icmp_hdr(skb)->type;
+		icmp_out_count(net, icmp_type);
+	}
 
 	ip_cork_release(cork);
 out:
@@ -1688,7 +1714,7 @@
 			   tcp_hdr(skb)->source, tcp_hdr(skb)->dest,
 			   arg->uid);
 	security_skb_classify_flow(skb, flowi4_to_flowi_common(&fl4));
-	rt = ip_route_output_key(net, &fl4);
+	rt = ip_route_output_flow(net, &fl4, sk);
 	if (IS_ERR(rt))
 		return;
 
@@ -1696,7 +1722,7 @@
 
 	sk->sk_protocol = ip_hdr(skb)->protocol;
 	sk->sk_bound_dev_if = arg->bound_dev_if;
-	sk->sk_sndbuf = sysctl_wmem_default;
+	sk->sk_sndbuf = READ_ONCE(sysctl_wmem_default);
 	ipc.sockc.mark = fl4.flowi4_mark;
 	err = ip_append_data(sk, &fl4, ip_reply_glue_bits, arg->iov->iov_base,
 			     len, 0, &ipc, &rt, MSG_DONTWAIT);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_sockglue.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_sockglue.c
@@ -130,20 +130,20 @@
 
 static void ip_cmsg_recv_security(struct msghdr *msg, struct sk_buff *skb)
 {
-	char *secdata;
-	u32 seclen, secid;
+	struct lsmcontext context;
+	struct lsmblob lb;
 	int err;
 
-	err = security_socket_getpeersec_dgram(NULL, skb, &secid);
+	err = security_socket_getpeersec_dgram(NULL, skb, &lb);
 	if (err)
 		return;
 
-	err = security_secid_to_secctx(secid, &secdata, &seclen);
+	err = security_secid_to_secctx(&lb, &context, LSMBLOB_DISPLAY);
 	if (err)
 		return;
 
-	put_cmsg(msg, SOL_IP, SCM_SECURITY, seclen, secdata);
-	security_release_secctx(secdata, seclen);
+	put_cmsg(msg, SOL_IP, SCM_SECURITY, context.len, context.context);
+	security_release_secctx(&context);
 }
 
 static void ip_cmsg_recv_dstaddr(struct msghdr *msg, struct sk_buff *skb)
@@ -317,7 +317,14 @@
 			ipc->tos = val;
 			ipc->priority = rt_tos2priority(ipc->tos);
 			break;
-
+		case IP_PROTOCOL:
+			if (cmsg->cmsg_len != CMSG_LEN(sizeof(int)))
+				return -EINVAL;
+			val = *(int *)CMSG_DATA(cmsg);
+			if (val < 1 || val > 255)
+				return -EINVAL;
+			ipc->protocol = val;
+			break;
 		default:
 			return -EINVAL;
 		}
@@ -772,7 +779,7 @@
 
 	if (optlen < GROUP_FILTER_SIZE(0))
 		return -EINVAL;
-	if (optlen > sysctl_optmem_max)
+	if (optlen > READ_ONCE(sysctl_optmem_max))
 		return -ENOBUFS;
 
 	gsf = memdup_sockptr(optval, optlen);
@@ -782,7 +789,7 @@
 	/* numsrc >= (4G-140)/128 overflow in 32 bits */
 	err = -ENOBUFS;
 	if (gsf->gf_numsrc >= 0x1ffffff ||
-	    gsf->gf_numsrc > sock_net(sk)->ipv4.sysctl_igmp_max_msf)
+	    gsf->gf_numsrc > READ_ONCE(sock_net(sk)->ipv4.sysctl_igmp_max_msf))
 		goto out_free_gsf;
 
 	err = -EINVAL;
@@ -808,7 +815,7 @@
 
 	if (optlen < size0)
 		return -EINVAL;
-	if (optlen > sysctl_optmem_max - 4)
+	if (optlen > READ_ONCE(sysctl_optmem_max) - 4)
 		return -ENOBUFS;
 
 	p = kmalloc(optlen + 4, GFP_KERNEL);
@@ -832,7 +839,7 @@
 
 	/* numsrc >= (4G-140)/128 overflow in 32 bits */
 	err = -ENOBUFS;
-	if (n > sock_net(sk)->ipv4.sysctl_igmp_max_msf)
+	if (n > READ_ONCE(sock_net(sk)->ipv4.sysctl_igmp_max_msf))
 		goto out_free_gsf;
 	err = set_mcast_msfilter(sk, gf32->gf_interface, n, gf32->gf_fmode,
 				 &gf32->gf_group, gf32->gf_slist_flex);
@@ -1231,7 +1238,7 @@
 
 		if (optlen < IP_MSFILTER_SIZE(0))
 			goto e_inval;
-		if (optlen > sysctl_optmem_max) {
+		if (optlen > READ_ONCE(sysctl_optmem_max)) {
 			err = -ENOBUFS;
 			break;
 		}
@@ -1242,7 +1249,7 @@
 		}
 		/* numsrc >= (1G-4) overflow in 32 bits */
 		if (msf->imsf_numsrc >= 0x3ffffffcU ||
-		    msf->imsf_numsrc > net->ipv4.sysctl_igmp_max_msf) {
+		    msf->imsf_numsrc > READ_ONCE(net->ipv4.sysctl_igmp_max_msf)) {
 			kfree(msf);
 			err = -ENOBUFS;
 			break;
@@ -1453,37 +1460,37 @@
 	return false;
 }
 
-static int ip_get_mcast_msfilter(struct sock *sk, void __user *optval,
-		int __user *optlen, int len)
+static int ip_get_mcast_msfilter(struct sock *sk, sockptr_t optval,
+				 sockptr_t optlen, int len)
 {
 	const int size0 = offsetof(struct group_filter, gf_slist_flex);
-	struct group_filter __user *p = optval;
 	struct group_filter gsf;
-	int num;
+	int num, gsf_size;
 	int err;
 
 	if (len < size0)
 		return -EINVAL;
-	if (copy_from_user(&gsf, p, size0))
+	if (copy_from_sockptr(&gsf, optval, size0))
 		return -EFAULT;
 
 	num = gsf.gf_numsrc;
-	err = ip_mc_gsfget(sk, &gsf, p->gf_slist_flex);
+	err = ip_mc_gsfget(sk, &gsf, optval,
+			   offsetof(struct group_filter, gf_slist_flex));
 	if (err)
 		return err;
 	if (gsf.gf_numsrc < num)
 		num = gsf.gf_numsrc;
-	if (put_user(GROUP_FILTER_SIZE(num), optlen) ||
-	    copy_to_user(p, &gsf, size0))
+	gsf_size = GROUP_FILTER_SIZE(num);
+	if (copy_to_sockptr(optlen, &gsf_size, sizeof(int)) ||
+	    copy_to_sockptr(optval, &gsf, size0))
 		return -EFAULT;
 	return 0;
 }
 
-static int compat_ip_get_mcast_msfilter(struct sock *sk, void __user *optval,
-		int __user *optlen, int len)
+static int compat_ip_get_mcast_msfilter(struct sock *sk, sockptr_t optval,
+					sockptr_t optlen, int len)
 {
 	const int size0 = offsetof(struct compat_group_filter, gf_slist_flex);
-	struct compat_group_filter __user *p = optval;
 	struct compat_group_filter gf32;
 	struct group_filter gf;
 	int num;
@@ -1491,7 +1498,7 @@
 
 	if (len < size0)
 		return -EINVAL;
-	if (copy_from_user(&gf32, p, size0))
+	if (copy_from_sockptr(&gf32, optval, size0))
 		return -EFAULT;
 
 	gf.gf_interface = gf32.gf_interface;
@@ -1499,21 +1506,24 @@
 	num = gf.gf_numsrc = gf32.gf_numsrc;
 	gf.gf_group = gf32.gf_group;
 
-	err = ip_mc_gsfget(sk, &gf, p->gf_slist_flex);
+	err = ip_mc_gsfget(sk, &gf, optval,
+			   offsetof(struct compat_group_filter, gf_slist_flex));
 	if (err)
 		return err;
 	if (gf.gf_numsrc < num)
 		num = gf.gf_numsrc;
 	len = GROUP_FILTER_SIZE(num) - (sizeof(gf) - sizeof(gf32));
-	if (put_user(len, optlen) ||
-	    put_user(gf.gf_fmode, &p->gf_fmode) ||
-	    put_user(gf.gf_numsrc, &p->gf_numsrc))
+	if (copy_to_sockptr(optlen, &len, sizeof(int)) ||
+	    copy_to_sockptr_offset(optval, offsetof(struct compat_group_filter, gf_fmode),
+				   &gf.gf_fmode, sizeof(gf.gf_fmode)) ||
+	    copy_to_sockptr_offset(optval, offsetof(struct compat_group_filter, gf_numsrc),
+				   &gf.gf_numsrc, sizeof(gf.gf_numsrc)))
 		return -EFAULT;
 	return 0;
 }
 
 static int do_ip_getsockopt(struct sock *sk, int level, int optname,
-			    char __user *optval, int __user *optlen)
+			    sockptr_t optval, sockptr_t optlen)
 {
 	struct inet_sock *inet = inet_sk(sk);
 	bool needs_rtnl = getsockopt_needs_rtnl(optname);
@@ -1526,7 +1536,7 @@
 	if (ip_mroute_opt(optname))
 		return ip_mroute_getsockopt(sk, optname, optval, optlen);
 
-	if (get_user(len, optlen))
+	if (copy_from_sockptr(&len, optlen, sizeof(int)))
 		return -EFAULT;
 	if (len < 0)
 		return -EINVAL;
@@ -1551,15 +1561,17 @@
 			       inet_opt->opt.optlen);
 		release_sock(sk);
 
-		if (opt->optlen == 0)
-			return put_user(0, optlen);
+		if (opt->optlen == 0) {
+			len = 0;
+			return copy_to_sockptr(optlen, &len, sizeof(int));
+		}
 
 		ip_options_undo(opt);
 
 		len = min_t(unsigned int, len, opt->optlen);
-		if (put_user(len, optlen))
+		if (copy_to_sockptr(optlen, &len, sizeof(int)))
 			return -EFAULT;
-		if (copy_to_user(optval, opt->__data, len))
+		if (copy_to_sockptr(optval, opt->__data, len))
 			return -EFAULT;
 		return 0;
 	}
@@ -1597,7 +1609,7 @@
 	{
 		struct net *net = sock_net(sk);
 		val = (inet->uc_ttl == -1 ?
-		       net->ipv4.sysctl_ip_default_ttl :
+		       READ_ONCE(net->ipv4.sysctl_ip_default_ttl) :
 		       inet->uc_ttl);
 		break;
 	}
@@ -1650,9 +1662,9 @@
 		addr.s_addr = inet->mc_addr;
 		release_sock(sk);
 
-		if (put_user(len, optlen))
+		if (copy_to_sockptr(optlen, &len, sizeof(int)))
 			return -EFAULT;
-		if (copy_to_user(optval, &addr, len))
+		if (copy_to_sockptr(optval, &addr, len))
 			return -EFAULT;
 		return 0;
 	}
@@ -1664,12 +1676,11 @@
 			err = -EINVAL;
 			goto out;
 		}
-		if (copy_from_user(&msf, optval, IP_MSFILTER_SIZE(0))) {
+		if (copy_from_sockptr(&msf, optval, IP_MSFILTER_SIZE(0))) {
 			err = -EFAULT;
 			goto out;
 		}
-		err = ip_mc_msfget(sk, &msf,
-				   (struct ip_msfilter __user *)optval, optlen);
+		err = ip_mc_msfget(sk, &msf, optval, optlen);
 		goto out;
 	}
 	case MCAST_MSFILTER:
@@ -1691,8 +1702,13 @@
 		if (sk->sk_type != SOCK_STREAM)
 			return -ENOPROTOOPT;
 
-		msg.msg_control_is_user = true;
-		msg.msg_control_user = optval;
+		if (optval.is_kernel) {
+			msg.msg_control_is_user = false;
+			msg.msg_control = optval.kernel;
+		} else {
+			msg.msg_control_is_user = true;
+			msg.msg_control_user = optval.user;
+		}
 		msg.msg_controllen = len;
 		msg.msg_flags = in_compat_syscall() ? MSG_CMSG_COMPAT : 0;
 
@@ -1713,7 +1729,7 @@
 			put_cmsg(&msg, SOL_IP, IP_TOS, sizeof(tos), &tos);
 		}
 		len -= msg.msg_controllen;
-		return put_user(len, optlen);
+		return copy_to_sockptr(optlen, &len, sizeof(int));
 	}
 	case IP_FREEBIND:
 		val = inet->freebind;
@@ -1724,6 +1740,9 @@
 	case IP_MINTTL:
 		val = inet->min_ttl;
 		break;
+	case IP_PROTOCOL:
+		val = inet_sk(sk)->inet_num;
+		break;
 	default:
 		release_sock(sk);
 		return -ENOPROTOOPT;
@@ -1733,15 +1752,15 @@
 	if (len < sizeof(int) && len > 0 && val >= 0 && val <= 255) {
 		unsigned char ucval = (unsigned char)val;
 		len = 1;
-		if (put_user(len, optlen))
+		if (copy_to_sockptr(optlen, &len, sizeof(int)))
 			return -EFAULT;
-		if (copy_to_user(optval, &ucval, 1))
+		if (copy_to_sockptr(optval, &ucval, 1))
 			return -EFAULT;
 	} else {
 		len = min_t(unsigned int, sizeof(int), len);
-		if (put_user(len, optlen))
+		if (copy_to_sockptr(optlen, &len, sizeof(int)))
 			return -EFAULT;
-		if (copy_to_user(optval, &val, len))
+		if (copy_to_sockptr(optval, &val, len))
 			return -EFAULT;
 	}
 	return 0;
@@ -1758,7 +1777,8 @@
 {
 	int err;
 
-	err = do_ip_getsockopt(sk, level, optname, optval, optlen);
+	err = do_ip_getsockopt(sk, level, optname,
+			       USER_SOCKPTR(optval), USER_SOCKPTR(optlen));
 
 #if IS_ENABLED(CONFIG_BPFILTER_UMH)
 	if (optname >= BPFILTER_IPT_SO_GET_INFO &&
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_tunnel.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_tunnel.c
@@ -218,7 +218,7 @@
 	struct ip_tunnel *t = NULL;
 	struct hlist_head *head = ip_bucket(itn, parms);
 
-	hlist_for_each_entry_rcu(t, head, hash_node) {
+	hlist_for_each_entry_rcu(t, head, hash_node, lockdep_rtnl_is_held()) {
 		if (local == t->parms.iph.saddr &&
 		    remote == t->parms.iph.daddr &&
 		    link == t->parms.link &&
@@ -294,8 +294,8 @@
 
 		ip_tunnel_init_flow(&fl4, iph->protocol, iph->daddr,
 				    iph->saddr, tunnel->parms.o_key,
-				    RT_TOS(iph->tos), tunnel->parms.link,
-				    tunnel->fwmark, 0);
+				    RT_TOS(iph->tos), dev_net(dev),
+				    tunnel->parms.link, tunnel->fwmark, 0);
 		rt = ip_route_output_key(tunnel->net, &fl4);
 
 		if (!IS_ERR(rt)) {
@@ -364,7 +364,7 @@
 		  bool log_ecn_error)
 {
 	const struct iphdr *iph = ip_hdr(skb);
-	int err;
+	int nh, err;
 
 #ifdef CONFIG_NET_IPGRE_BROADCAST
 	if (ipv4_is_multicast(iph->daddr)) {
@@ -390,8 +390,21 @@
 		tunnel->i_seqno = ntohl(tpi->seq) + 1;
 	}
 
+	/* Save offset of outer header relative to skb->head,
+	 * because we are going to reset the network header to the inner header
+	 * and might change skb->head.
+	 */
+	nh = skb_network_header(skb) - skb->head;
+
 	skb_set_network_header(skb, (tunnel->dev->type == ARPHRD_ETHER) ? ETH_HLEN : 0);
 
+	if (!pskb_inet_may_pull(skb)) {
+		DEV_STATS_INC(tunnel->dev, rx_length_errors);
+		DEV_STATS_INC(tunnel->dev, rx_errors);
+		goto drop;
+	}
+	iph = (struct iphdr *)(skb->head + nh);
+
 	err = IP_ECN_decapsulate(iph, skb);
 	if (unlikely(err)) {
 		if (log_ecn_error)
@@ -540,6 +553,20 @@
 	return 0;
 }
 
+static void ip_tunnel_adj_headroom(struct net_device *dev, unsigned int headroom)
+{
+	/* we must cap headroom to some upperlimit, else pskb_expand_head
+	 * will overflow header offsets in skb_headers_offset_update().
+	 */
+	static const unsigned int max_allowed = 512;
+
+	if (headroom > max_allowed)
+		headroom = max_allowed;
+
+	if (headroom > READ_ONCE(dev->needed_headroom))
+		WRITE_ONCE(dev->needed_headroom, headroom);
+}
+
 void ip_md_tunnel_xmit(struct sk_buff *skb, struct net_device *dev,
 		       u8 proto, int tunnel_hlen)
 {
@@ -570,7 +597,7 @@
 	}
 	ip_tunnel_init_flow(&fl4, proto, key->u.ipv4.dst, key->u.ipv4.src,
 			    tunnel_id_to_key32(key->tun_id), RT_TOS(tos),
-			    0, skb->mark, skb_get_hash(skb));
+			    dev_net(dev), 0, skb->mark, skb_get_hash(skb));
 	if (tunnel->encap.type != TUNNEL_ENCAP_NONE)
 		goto tx_error;
 
@@ -613,13 +640,13 @@
 	}
 
 	headroom += LL_RESERVED_SPACE(rt->dst.dev) + rt->dst.header_len;
-	if (headroom > dev->needed_headroom)
-		dev->needed_headroom = headroom;
-
-	if (skb_cow_head(skb, dev->needed_headroom)) {
+	if (skb_cow_head(skb, headroom)) {
 		ip_rt_put(rt);
 		goto tx_dropped;
 	}
+
+	ip_tunnel_adj_headroom(dev, headroom);
+
 	iptunnel_xmit(NULL, rt, skb, fl4.saddr, fl4.daddr, proto, tos, ttl,
 		      df, !net_eq(tunnel->net, dev_net(dev)));
 	return;
@@ -726,7 +753,8 @@
 	}
 
 	ip_tunnel_init_flow(&fl4, protocol, dst, tnl_params->saddr,
-			    tunnel->parms.o_key, RT_TOS(tos), tunnel->parms.link,
+			    tunnel->parms.o_key, RT_TOS(tos),
+			    dev_net(dev), tunnel->parms.link,
 			    tunnel->fwmark, skb_get_hash(skb));
 
 	if (ip_tunnel_encap(skb, tunnel, &protocol, &fl4) < 0)
@@ -797,16 +825,16 @@
 
 	max_headroom = LL_RESERVED_SPACE(rt->dst.dev) + sizeof(struct iphdr)
 			+ rt->dst.header_len + ip_encap_hlen(&tunnel->encap);
-	if (max_headroom > dev->needed_headroom)
-		dev->needed_headroom = max_headroom;
 
-	if (skb_cow_head(skb, dev->needed_headroom)) {
+	if (skb_cow_head(skb, max_headroom)) {
 		ip_rt_put(rt);
 		dev->stats.tx_dropped++;
 		kfree_skb(skb);
 		return;
 	}
 
+	ip_tunnel_adj_headroom(dev, max_headroom);
+
 	iptunnel_xmit(NULL, rt, skb, fl4.saddr, fl4.daddr, protocol, tos, ttl,
 		      df, !net_eq(tunnel->net, dev_net(dev)));
 	return;
@@ -1188,7 +1216,7 @@
 	struct ip_tunnel_net *itn = net_generic(net, tunnel->ip_tnl_net_id);
 
 	if (dev == itn->fb_tunnel_dev)
-		return -EINVAL;
+		return fan_has_map(&tunnel->fan) ? 0 : -EINVAL;
 
 	t = ip_tunnel_find(itn, p, dev->type);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_tunnel_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_tunnel_core.c
@@ -224,7 +224,7 @@
 		.un.frag.__unused	= 0,
 		.un.frag.mtu		= htons(mtu),
 	};
-	icmph->checksum = ip_compute_csum(icmph, len);
+	icmph->checksum = csum_fold(skb_checksum(skb, 0, len, 0));
 	skb_reset_transport_header(skb);
 
 	niph = skb_push(skb, sizeof(*niph));
@@ -332,7 +332,7 @@
 	};
 	skb_reset_network_header(skb);
 
-	csum = csum_partial(icmp6h, len, 0);
+	csum = skb_checksum(skb, skb_transport_offset(skb), len, 0);
 	icmp6h->icmp6_cksum = csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr, len,
 					      IPPROTO_ICMPV6, csum);
 
@@ -410,12 +410,12 @@
 	u32 mtu = dst_mtu(encap_dst) - headroom;
 
 	if ((skb_is_gso(skb) && skb_gso_validate_network_len(skb, mtu)) ||
-	    (!skb_is_gso(skb) && (skb->len - skb_mac_header_len(skb)) <= mtu))
+	    (!skb_is_gso(skb) && (skb->len - skb_network_offset(skb)) <= mtu))
 		return 0;
 
 	skb_dst_update_pmtu_no_confirm(skb, mtu);
 
-	if (!reply || skb->pkt_type == PACKET_HOST)
+	if (!reply)
 		return 0;
 
 	if (skb->protocol == htons(ETH_P_IP))
@@ -450,7 +450,7 @@
 geneve_opt_policy[LWTUNNEL_IP_OPT_GENEVE_MAX + 1] = {
 	[LWTUNNEL_IP_OPT_GENEVE_CLASS]	= { .type = NLA_U16 },
 	[LWTUNNEL_IP_OPT_GENEVE_TYPE]	= { .type = NLA_U8 },
-	[LWTUNNEL_IP_OPT_GENEVE_DATA]	= { .type = NLA_BINARY, .len = 128 },
+	[LWTUNNEL_IP_OPT_GENEVE_DATA]	= { .type = NLA_BINARY, .len = 127 },
 };
 
 static const struct nla_policy
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ip_vti.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ip_vti.c
@@ -287,12 +287,12 @@
 
 	switch (skb->protocol) {
 	case htons(ETH_P_IP):
-		xfrm_decode_session(skb, &fl, AF_INET);
 		memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
+		xfrm_decode_session(skb, &fl, AF_INET);
 		break;
 	case htons(ETH_P_IPV6):
-		xfrm_decode_session(skb, &fl, AF_INET6);
 		memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
+		xfrm_decode_session(skb, &fl, AF_INET6);
 		break;
 	default:
 		goto tx_err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ipip.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ipip.c
@@ -101,6 +101,8 @@
 #include <linux/init.h>
 #include <linux/netfilter_ipv4.h>
 #include <linux/if_ether.h>
+#include <linux/inetdevice.h>
+#include <linux/rculist.h>
 
 #include <net/sock.h>
 #include <net/ip.h>
@@ -266,6 +268,147 @@
 }
 #endif
 
+static struct ip_fan_map *ipip_fan_find_map(struct ip_tunnel *t, __be32 daddr)
+{
+	struct ip_fan_map *fan_map;
+
+	rcu_read_lock();
+	list_for_each_entry_rcu(fan_map, &t->fan.fan_maps, list) {
+		if (fan_map->overlay ==
+		    (daddr & inet_make_mask(fan_map->overlay_prefix))) {
+			rcu_read_unlock();
+			return fan_map;
+		}
+	}
+	rcu_read_unlock();
+
+	return NULL;
+}
+
+/* Determine fan tunnel endpoint to send packet to, based on the inner IP
+ * address.  
+ *
+ * Given a /8 overlay and /16 underlay, for an overlay (inner) address
+ * Y.A.B.C, the transformation is F.G.A.B, where "F" and "G" are the first
+ * two octets of the underlay network (the network portion of a /16), "A"
+ * and "B" are the low order two octets of the underlay network host (the
+ * host portion of a /16), and "Y" is a configured first octet of the
+ * overlay network.
+ *
+ * E.g., underlay host 10.88.3.4/16 with an overlay of 99.0.0.0/8 would
+ * host overlay subnet 99.3.4.0/24.  An overlay network datagram from
+ * 99.3.4.5 to 99.6.7.8, would be directed to underlay host 10.88.6.7,
+ * which hosts overlay network subnet 99.6.7.0/24.  This transformation is
+ * described in detail further below.
+ *
+ * Using netmasks for the overlay and underlay other than /8 and /16, as
+ * shown above, can yield larger (or smaller) overlay subnets, with the
+ * trade-off of allowing fewer (or more) underlay hosts to participate.
+ *
+ * The size of each overlay network subnet is defined by the total of the
+ * network mask of the overlay plus the size of host portion of the
+ * underlay network. In the above example, /8 + /16 = /24.
+ *
+ * E.g., consider underlay host 10.99.238.5/20 and overlay 99.0.0.0/8. In
+ * this case, the network portion of the underlay is 10.99.224.0/20, and
+ * the host portion is 0.0.14.5 (12 bits).  To determine the overlay
+ * network subnet, the 12 bits of host portion are left shifted 12 bits
+ * (/20 - /8) and ORed with the overlay subnet prefix.  This yields an
+ * overlay subnet of 99.224.80/20, composed of 8 bits overlay, followed by
+ * 12 bits underlay.  This yields 12 bits in the overlay network portion,
+ * allowing for 4094 addresses in each overlay network subnet.  The
+ * trade-off is that fewer hosts may participate in the underlay network,
+ * as its host address size has shrunk from 16 bits (65534 addresses) in
+ * the first example to 12 bits (4094 addresses) here.
+ *
+ * For fewer hosts per overlay subnet (permitting a larger number of
+ * underlay hosts to participate), the underlay netmask may be made
+ * smaller.
+ *
+ * E.g., underlay host 10.111.1.2/12 (network 10.96.0.0/12, host portion
+ * is 0.15.1.2, 20 bits) with an overlay of 33.0.0.0/8 would left shift
+ * the 20 bits of host by 4 (so that it's highest order bit is adjacent to
+ * the lowest order bit of the /8 overlay).  This yields an overlay subnet
+ * of 33.240.16.32/28 (8 bits overlay, 20 bits from the host portion of
+ * the underlay).  This provides more addresses for the underlay network
+ * (approximately 2^20), but each host's segment of the overlay provides
+ * only 4 bits of addresses (14 usable).
+ *
+ * It is also possible to adjust the overlay subnet.
+ *
+ * For an overlay of 240.0.0.0/5 and underlay of 10.88.0.0/20, consider
+ * underlay host 10.88.129.2; the 12 bits of host, 0.0.1.2, are left
+ * shifted 15 bits (/20 - /5), yielding an overlay network of
+ * 240.129.0.0/17.  An underlay host of 10.88.244.215 would yield an
+ * overlay network of 242.107.128.0/17.
+ *
+ * For an overlay of 100.64.0.0/10 and underlay of 10.224.220.0/24, for
+ * underlay host 10.224.220.10, the underlay host portion (.10) is left
+ * shifted 14 bits, yielding an overlay network subnet of 100.66.128.0/18.
+ * This would permit 254 addresses on the underlay, with each overlay
+ * segment providing approximately 2^14 - 2 addresses (16382).
+ *
+ * For packets being encapsulated, the overlay network destination IP
+ * address is deconstructed into its overlay and underlay-derived
+ * portions.  The underlay portion (determined by the overlay mask and
+ * overlay subnet mask) is right shifted according to the size of the
+ * underlay network mask.  This value is then ORed with the network
+ * portion of the underlay network to produce the underlay network
+ * destination for the encapsulated datagram.
+ *
+ * For example, using the initial example of underlay 10.88.3.4/16 and
+ * overlay 99.0.0.0/8, with underlay host 10.88.3.4/16 providing overlay
+ * subnet 99.3.4.0/24 with specfic host 99.3.4.5.  A datagram from
+ * 99.3.4.5 to 99.6.7.8 would first have the underlay host derived portion
+ * of the address extracted.  This is a number of bits equal to underlay
+ * network host portion.  In the destination address, the highest order of
+ * these bits is one bit lower than the lowest order bit from the overlay
+ * network mask.
+ *
+ * Using the sample value, 99.6.7.8, the overlay mask is /8, and the
+ * underlay mask is /16 (leaving 16 bits for the host portion).  The bits
+ * to be shifted are the middle two octets, 0.6.7.0, as this is 99.6.7.8
+ * ANDed with the mask 0x00ffff00 (which is 16 bits, the highest order of
+ * which is 1 bit lower than the lowest order overlay address bit).
+ *
+ * These octets, 0.6.7.0, are then right shifted 8 bits, yielding 0.0.6.7.
+ * This value is then ORed with the underlay network portion,
+ * 10.88.0.0/16, providing 10.88.6.7 as the final underlay destination for
+ * the encapuslated datagram.
+ *
+ * Another transform using the final example: overlay 100.64.0.0/10 and
+ * underlay 10.224.220.0/24.  Consider overlay address 100.66.128.1
+ * sending a datagram to 100.66.200.5.  In this case, 8 bits (the host
+ * portion size of 10.224.220.0/24) beginning after the 100.64/10 overlay
+ * prefix are masked off, yielding 0.2.192.0.  This is right shifted 14
+ * (32 - 10 - (32 - 24), i.e., the number of bits between the overlay
+ * network portion and the underlay host portion) bits, yielding 0.0.0.11.
+ * This is ORed with the underlay network portion, 10.224.220.0/24, giving
+ * the underlay destination of 10.224.220.11 for overlay destination
+ * 100.66.200.5.
+ */
+static int ipip_build_fan_iphdr(struct ip_tunnel *tunnel, struct sk_buff *skb, struct iphdr *iph)
+{
+	struct ip_fan_map *f_map;
+	u32 daddr, underlay;
+
+	f_map = ipip_fan_find_map(tunnel, ip_hdr(skb)->daddr);
+	if (!f_map)
+		return -ENOENT;
+
+	daddr = ntohl(ip_hdr(skb)->daddr);
+	underlay = ntohl(f_map->underlay);
+	if (!underlay)
+		return -EINVAL;
+
+	*iph = tunnel->parms.iph;
+	iph->daddr = htonl(underlay |
+			   ((daddr & ~f_map->overlay_mask) >>
+			    (32 - f_map->overlay_prefix -
+			     (32 - f_map->underlay_prefix))));
+	return 0;
+}
+
 /*
  *	This function assumes it is being called from dev_queue_xmit()
  *	and that skb is filled properly by that function.
@@ -276,6 +419,7 @@
 	struct ip_tunnel *tunnel = netdev_priv(dev);
 	const struct iphdr  *tiph = &tunnel->parms.iph;
 	u8 ipproto;
+	struct iphdr fiph;
 
 	if (!pskb_inet_may_pull(skb))
 		goto tx_error;
@@ -299,6 +443,14 @@
 	if (iptunnel_handle_offloads(skb, SKB_GSO_IPXIP4))
 		goto tx_error;
 
+	if (fan_has_map(&tunnel->fan)) {
+		if (ipip_build_fan_iphdr(tunnel, skb, &fiph))
+			goto tx_error;
+		tiph = &fiph;
+	} else {
+		tiph = &tunnel->parms.iph;
+	}
+
 	skb_set_inner_ipproto(skb, ipproto);
 
 	if (tunnel->collect_md)
@@ -362,6 +514,8 @@
 
 static void ipip_tunnel_setup(struct net_device *dev)
 {
+	struct ip_tunnel *t = netdev_priv(dev);
+
 	dev->netdev_ops		= &ipip_netdev_ops;
 	dev->header_ops		= &ip_tunnel_header_ops;
 
@@ -374,6 +528,7 @@
 	dev->features		|= IPIP_FEATURES;
 	dev->hw_features	|= IPIP_FEATURES;
 	ip_tunnel_setup(dev, ipip_net_id);
+	INIT_LIST_HEAD(&t->fan.fan_maps);
 }
 
 static int ipip_tunnel_init(struct net_device *dev)
@@ -482,6 +637,93 @@
 	return ret;
 }
 
+static void ipip_fan_flush_map(struct ip_tunnel *t)
+{
+	struct ip_fan_map *fan_map;
+
+	list_for_each_entry_rcu(fan_map, &t->fan.fan_maps, list) {
+		list_del_rcu(&fan_map->list);
+		kfree_rcu(fan_map, rcu);
+	}
+}
+
+static int ipip_fan_del_map(struct ip_tunnel *t, __be32 overlay)
+{
+	struct ip_fan_map *fan_map;
+
+	fan_map = ipip_fan_find_map(t, overlay);
+	if (!fan_map)
+		return -ENOENT;
+
+	list_del_rcu(&fan_map->list);
+	kfree_rcu(fan_map, rcu);
+
+	return 0;
+}
+
+static int ipip_fan_add_map(struct ip_tunnel *t, struct ifla_fan_map *map)
+{
+	__be32 overlay_mask, underlay_mask;
+	struct ip_fan_map *fan_map;
+
+	overlay_mask = inet_make_mask(map->overlay_prefix);
+	underlay_mask = inet_make_mask(map->underlay_prefix);
+
+	if ((map->overlay & ~overlay_mask) || (map->underlay & ~underlay_mask))
+		return -EINVAL;
+
+	if (!(map->overlay & overlay_mask) && (map->underlay & underlay_mask))
+		return -EINVAL;
+
+	/* Special case: overlay 0 and underlay 0: flush all mappings */
+	if (!map->overlay && !map->underlay) {
+		ipip_fan_flush_map(t);
+		return 0;
+	}
+	
+	/* Special case: overlay set and underlay 0: clear map for overlay */
+	if (!map->underlay)
+		return ipip_fan_del_map(t, map->overlay);
+
+	if (ipip_fan_find_map(t, map->overlay))
+		return -EEXIST;
+
+	fan_map = kmalloc(sizeof(*fan_map), GFP_KERNEL);
+	fan_map->underlay = map->underlay;
+	fan_map->overlay = map->overlay;
+	fan_map->underlay_prefix = map->underlay_prefix;
+	fan_map->overlay_mask = ntohl(overlay_mask);
+	fan_map->overlay_prefix = map->overlay_prefix;
+
+	list_add_tail_rcu(&fan_map->list, &t->fan.fan_maps);
+
+	return 0;
+}
+	
+
+static int ipip_netlink_fan(struct nlattr *data[], struct ip_tunnel *t,
+			    struct ip_tunnel_parm *parms)
+{
+	struct ifla_fan_map *map;
+	struct nlattr *attr;
+	int rem, rv;
+
+	if (data == NULL || !data[IFLA_IPTUN_FAN_MAP])
+		return 0;
+
+	if (parms->iph.daddr)
+		return -EINVAL;
+
+	nla_for_each_nested(attr, data[IFLA_IPTUN_FAN_MAP], rem) {
+		map = nla_data(attr);
+		rv = ipip_fan_add_map(t, map);
+		if (rv)
+			return rv;
+	}
+
+	return 0;
+}
+
 static int ipip_newlink(struct net *src_net, struct net_device *dev,
 			struct nlattr *tb[], struct nlattr *data[],
 			struct netlink_ext_ack *extack)
@@ -490,15 +732,19 @@
 	struct ip_tunnel_parm p;
 	struct ip_tunnel_encap ipencap;
 	__u32 fwmark = 0;
+	int err;
 
 	if (ipip_netlink_encap_parms(data, &ipencap)) {
-		int err = ip_tunnel_encap_setup(t, &ipencap);
+		err = ip_tunnel_encap_setup(t, &ipencap);
 
 		if (err < 0)
 			return err;
 	}
 
 	ipip_netlink_parms(data, &p, &t->collect_md, &fwmark);
+	err = ipip_netlink_fan(data, t, &p);
+	if (err < 0)
+		return err;
 	return ip_tunnel_newlink(dev, tb, &p, fwmark);
 }
 
@@ -511,9 +757,10 @@
 	struct ip_tunnel_encap ipencap;
 	bool collect_md;
 	__u32 fwmark = t->fwmark;
+	int err;
 
 	if (ipip_netlink_encap_parms(data, &ipencap)) {
-		int err = ip_tunnel_encap_setup(t, &ipencap);
+		err = ip_tunnel_encap_setup(t, &ipencap);
 
 		if (err < 0)
 			return err;
@@ -522,6 +769,9 @@
 	ipip_netlink_parms(data, &p, &collect_md, &fwmark);
 	if (collect_md)
 		return -EINVAL;
+	err = ipip_netlink_fan(data, t, &p);
+	if (err < 0)
+		return err;
 
 	if (((dev->flags & IFF_POINTOPOINT) && !p.iph.daddr) ||
 	    (!(dev->flags & IFF_POINTOPOINT) && p.iph.daddr))
@@ -559,6 +809,8 @@
 		nla_total_size(0) +
 		/* IFLA_IPTUN_FWMARK */
 		nla_total_size(4) +
+		/* IFLA_IPTUN_FAN_MAP */
+		nla_total_size(sizeof(struct ifla_fan_map)) * 256 +
 		0;
 }
 
@@ -591,6 +843,26 @@
 	if (tunnel->collect_md)
 		if (nla_put_flag(skb, IFLA_IPTUN_COLLECT_METADATA))
 			goto nla_put_failure;
+	if (fan_has_map(&tunnel->fan)) {
+		struct nlattr *fan_nest;
+		struct ip_fan_map *fan_map;
+
+		fan_nest = nla_nest_start(skb, IFLA_IPTUN_FAN_MAP);
+		if (!fan_nest)
+			goto nla_put_failure;
+		list_for_each_entry_rcu(fan_map, &tunnel->fan.fan_maps, list) {
+			struct ifla_fan_map map;
+
+			map.underlay = fan_map->underlay;
+			map.underlay_prefix = fan_map->underlay_prefix;
+			map.overlay = fan_map->overlay;
+			map.overlay_prefix = fan_map->overlay_prefix;
+			if (nla_put(skb, IFLA_FAN_MAPPING, sizeof(map), &map))
+				goto nla_put_failure;
+		}
+		nla_nest_end(skb, fan_nest);
+	}
+
 	return 0;
 
 nla_put_failure:
@@ -611,6 +883,9 @@
 	[IFLA_IPTUN_ENCAP_DPORT]	= { .type = NLA_U16 },
 	[IFLA_IPTUN_COLLECT_METADATA]	= { .type = NLA_FLAG },
 	[IFLA_IPTUN_FWMARK]		= { .type = NLA_U32 },
+
+	[__IFLA_IPTUN_VENDOR_BREAK ... IFLA_IPTUN_MAX]	= { .type = NLA_BINARY },
+	[IFLA_IPTUN_FAN_MAP]		= { .type = NLA_NESTED },
 };
 
 static struct rtnl_link_ops ipip_link_ops __read_mostly = {
@@ -659,6 +934,23 @@
 	.size = sizeof(struct ip_tunnel_net),
 };
 
+#ifdef CONFIG_SYSCTL
+static struct ctl_table_header *ipip_fan_header;
+static unsigned int ipip_fan_version = 3;
+
+static struct ctl_table ipip_fan_sysctls[] = {
+	{
+		.procname	= "version",
+		.data		= &ipip_fan_version,
+		.maxlen		= sizeof(ipip_fan_version),
+		.mode		= 0444,
+		.proc_handler	= proc_dointvec,
+	},
+	{},
+};
+
+#endif /* CONFIG_SYSCTL */
+
 static int __init ipip_init(void)
 {
 	int err;
@@ -684,9 +976,22 @@
 	if (err < 0)
 		goto rtnl_link_failed;
 
+#ifdef CONFIG_SYSCTL
+	ipip_fan_header = register_net_sysctl(&init_net, "net/fan",
+					      ipip_fan_sysctls);
+	if (!ipip_fan_header) {
+		err = -ENOMEM;
+		goto sysctl_failed;
+	}
+#endif /* CONFIG_SYSCTL */
+
 out:
 	return err;
 
+#ifdef CONFIG_SYSCTL
+sysctl_failed:
+	rtnl_link_unregister(&ipip_link_ops);
+#endif /* CONFIG_SYSCTL */
 rtnl_link_failed:
 #if IS_ENABLED(CONFIG_MPLS)
 	xfrm4_tunnel_deregister(&mplsip_handler, AF_MPLS);
@@ -701,6 +1006,9 @@
 
 static void __exit ipip_fini(void)
 {
+#ifdef CONFIG_SYSCTL
+	unregister_net_sysctl_table(ipip_fan_header);
+#endif /* CONFIG_SYSCTL */
 	rtnl_link_unregister(&ipip_link_ops);
 	if (xfrm4_tunnel_deregister(&ipip_handler, AF_INET))
 		pr_info("%s: can't deregister tunnel\n", __func__);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ipmr.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ipmr.c
@@ -261,7 +261,9 @@
 	return 0;
 
 err2:
+	rtnl_lock();
 	ipmr_free_table(mrt);
+	rtnl_unlock();
 err1:
 	fib_rules_unregister(ops);
 	return err;
@@ -1538,7 +1540,8 @@
 }
 
 /* Getsock opt support for the multicast routing system. */
-int ip_mroute_getsockopt(struct sock *sk, int optname, char __user *optval, int __user *optlen)
+int ip_mroute_getsockopt(struct sock *sk, int optname, sockptr_t optval,
+			 sockptr_t optlen)
 {
 	int olr;
 	int val;
@@ -1569,14 +1572,16 @@
 		return -ENOPROTOOPT;
 	}
 
-	if (get_user(olr, optlen))
+	if (copy_from_sockptr(&olr, optlen, sizeof(int)))
 		return -EFAULT;
-	olr = min_t(unsigned int, olr, sizeof(int));
 	if (olr < 0)
 		return -EINVAL;
-	if (put_user(olr, optlen))
+
+	olr = min_t(unsigned int, olr, sizeof(int));
+
+	if (copy_to_sockptr(optlen, &olr, sizeof(int)))
 		return -EFAULT;
-	if (copy_to_user(optval, &val, olr))
+	if (copy_to_sockptr(optval, &val, olr))
 		return -EFAULT;
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ipmr_base.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ipmr_base.c
@@ -301,7 +301,8 @@
 	if (filter->filter_set)
 		flags |= NLM_F_DUMP_FILTERED;
 
-	list_for_each_entry_rcu(mfc, &mrt->mfc_cache_list, list) {
+	list_for_each_entry_rcu(mfc, &mrt->mfc_cache_list, list,
+				lockdep_rtnl_is_held()) {
 		if (e < s_e)
 			goto next_entry;
 		if (filter->dev &&
@@ -320,9 +321,6 @@
 	list_for_each_entry(mfc, &mrt->mfc_unres_queue, list) {
 		if (e < s_e)
 			goto next_entry2;
-		if (filter->dev &&
-		    !mr_mfc_uses_dev(mrt, mfc, filter->dev))
-			goto next_entry2;
 
 		err = fill(mrt, skb, NETLINK_CB(cb->skb).portid,
 			   cb->nlh->nlmsg_seq, mfc, RTM_NEWROUTE, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/metrics.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/metrics.c
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 #include <linux/netlink.h>
+#include <linux/nospec.h>
 #include <linux/rtnetlink.h>
 #include <linux/types.h>
 #include <net/ip.h>
@@ -28,6 +29,7 @@
 			return -EINVAL;
 		}
 
+		type = array_index_nospec(type, RTAX_MAX + 1);
 		if (type == RTAX_CC_ALGO) {
 			char tmp[TCP_CA_NAME_MAX];
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/arp_tables.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/arp_tables.c
@@ -295,6 +295,17 @@
 	       memcmp(&e->arp, &uncond, sizeof(uncond)) == 0;
 }
 
+static bool next_offset_ok(const struct xt_table_info *t, unsigned int newpos)
+{
+	if (newpos > t->size - sizeof(struct arpt_entry))
+		return false;
+
+	if (newpos % __alignof__(struct arpt_entry) != 0)
+		return false;
+
+	return true;
+}
+
 /* Figures out from what hook each rule can be called: returns 0 if
  * there are loops.  Puts hook bitmask in comefrom.
  */
@@ -353,6 +364,8 @@
 
 				/* Move along one */
 				size = e->next_offset;
+				if (!next_offset_ok(newinfo, pos + size))
+					return 0;
 				e = entry0 + pos + size;
 				if (pos + size >= newinfo->size)
 					return 0;
@@ -374,6 +387,10 @@
 					if (newpos >= newinfo->size)
 						return 0;
 				}
+
+				if (!next_offset_ok(newinfo, newpos))
+					return 0;
+
 				e = entry0 + newpos;
 				e->counters.pcnt = pos;
 				pos = newpos;
@@ -955,6 +972,8 @@
 	void *loc_cpu_entry;
 	struct arpt_entry *iter;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -963,6 +982,8 @@
 		return -ENOMEM;
 	if (tmp.num_counters == 0)
 		return -EINVAL;
+	if ((u64)len < (u64)tmp.size + sizeof(tmp))
+		return -EINVAL;
 
 	tmp.name[sizeof(tmp.name)-1] = 0;
 
@@ -1253,6 +1274,8 @@
 	void *loc_cpu_entry;
 	struct arpt_entry *iter;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -1261,6 +1284,8 @@
 		return -ENOMEM;
 	if (tmp.num_counters == 0)
 		return -EINVAL;
+	if ((u64)len < (u64)tmp.size + sizeof(tmp))
+		return -EINVAL;
 
 	tmp.name[sizeof(tmp.name)-1] = 0;
 
@@ -1524,6 +1549,10 @@
 
 	new_table = xt_register_table(net, table, &bootstrap, newinfo);
 	if (IS_ERR(new_table)) {
+		struct arpt_entry *iter;
+
+		xt_entry_foreach(iter, loc_cpu_entry, newinfo->size)
+			cleanup_entry(iter, net);
 		xt_free_table_info(newinfo);
 		return PTR_ERR(new_table);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/ip_tables.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/ip_tables.c
@@ -362,6 +362,17 @@
 	else return verdict;
 }
 
+static bool next_offset_ok(const struct xt_table_info *t, unsigned int newpos)
+{
+	if (newpos > t->size - sizeof(struct ipt_entry))
+		return false;
+
+	if (newpos % __alignof__(struct ipt_entry) != 0)
+		return false;
+
+	return true;
+}
+
 /* Figures out from what hook each rule can be called: returns 0 if
    there are loops.  Puts hook bitmask in comefrom. */
 static int
@@ -417,6 +428,8 @@
 
 				/* Move along one */
 				size = e->next_offset;
+				if (!next_offset_ok(newinfo, pos + size))
+					return 0;
 				e = entry0 + pos + size;
 				if (pos + size >= newinfo->size)
 					return 0;
@@ -438,6 +451,10 @@
 					if (newpos >= newinfo->size)
 						return 0;
 				}
+
+				if (!next_offset_ok(newinfo, newpos))
+					return 0;
+
 				e = entry0 + newpos;
 				e->counters.pcnt = pos;
 				pos = newpos;
@@ -1044,7 +1061,6 @@
 	struct xt_counters *counters;
 	struct ipt_entry *iter;
 
-	ret = 0;
 	counters = xt_counters_alloc(num_counters);
 	if (!counters) {
 		ret = -ENOMEM;
@@ -1090,7 +1106,7 @@
 		net_warn_ratelimited("iptables: counters copy to user failed while replacing table\n");
 	}
 	vfree(counters);
-	return ret;
+	return 0;
 
  put_module:
 	module_put(t->me);
@@ -1110,6 +1126,8 @@
 	void *loc_cpu_entry;
 	struct ipt_entry *iter;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -1118,6 +1136,8 @@
 		return -ENOMEM;
 	if (tmp.num_counters == 0)
 		return -EINVAL;
+	if ((u64)len < (u64)tmp.size + sizeof(tmp))
+		return -EINVAL;
 
 	tmp.name[sizeof(tmp.name)-1] = 0;
 
@@ -1494,6 +1514,8 @@
 	void *loc_cpu_entry;
 	struct ipt_entry *iter;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -1502,6 +1524,8 @@
 		return -ENOMEM;
 	if (tmp.num_counters == 0)
 		return -EINVAL;
+	if ((u64)len < (u64)tmp.size + sizeof(tmp))
+		return -EINVAL;
 
 	tmp.name[sizeof(tmp.name)-1] = 0;
 
@@ -1741,6 +1765,10 @@
 
 	new_table = xt_register_table(net, table, &bootstrap, newinfo);
 	if (IS_ERR(new_table)) {
+		struct ipt_entry *iter;
+
+		xt_entry_foreach(iter, loc_cpu_entry, newinfo->size)
+			cleanup_entry(iter, net);
 		xt_free_table_info(newinfo);
 		return PTR_ERR(new_table);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/ipt_CLUSTERIP.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/ipt_CLUSTERIP.c
@@ -435,7 +435,7 @@
 
 	switch (ctinfo) {
 	case IP_CT_NEW:
-		ct->mark = hash;
+		WRITE_ONCE(ct->mark, hash);
 		break;
 	case IP_CT_RELATED:
 	case IP_CT_RELATED_REPLY:
@@ -452,7 +452,7 @@
 #ifdef DEBUG
 	nf_ct_dump_tuple_ip(&ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple);
 #endif
-	pr_debug("hash=%u ct_hash=%u ", hash, ct->mark);
+	pr_debug("hash=%u ct_hash=%u ", hash, READ_ONCE(ct->mark));
 	if (!clusterip_responsible(cipinfo->config, hash)) {
 		pr_debug("not responsible\n");
 		return NF_DROP;
@@ -520,8 +520,11 @@
 			if (IS_ERR(config))
 				return PTR_ERR(config);
 		}
-	} else if (memcmp(&config->clustermac, &cipinfo->clustermac, ETH_ALEN))
+	} else if (memcmp(&config->clustermac, &cipinfo->clustermac, ETH_ALEN)) {
+		clusterip_config_entry_put(config);
+		clusterip_config_put(config);
 		return -EINVAL;
+	}
 
 	ret = nf_ct_netns_get(par->net, par->family);
 	if (ret < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/ipt_rpfilter.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/ipt_rpfilter.c
@@ -78,7 +78,8 @@
 	flow.flowi4_mark = info->flags & XT_RPFILTER_VALID_MARK ? skb->mark : 0;
 	flow.flowi4_tos = iph->tos & IPTOS_RT_MASK;
 	flow.flowi4_scope = RT_SCOPE_UNIVERSE;
-	flow.flowi4_oif = l3mdev_master_ifindex_rcu(xt_in(par));
+	flow.flowi4_l3mdev = l3mdev_master_ifindex_rcu(xt_in(par));
+	flow.flowi4_uid = sock_net_uid(xt_net(par), NULL);
 
 	return rpfilter_lookup_reverse(xt_net(par), &flow, xt_in(par), info->flags) ^ invert;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/iptable_nat.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/iptable_nat.c
@@ -152,25 +152,27 @@
 
 static int __init iptable_nat_init(void)
 {
-	int ret = xt_register_template(&nf_nat_ipv4_table,
-				       iptable_nat_table_init);
+	int ret;
 
+	/* net->gen->ptr[iptable_nat_net_id] must be allocated
+	 * before calling iptable_nat_table_init().
+	 */
+	ret = register_pernet_subsys(&iptable_nat_net_ops);
 	if (ret < 0)
 		return ret;
 
-	ret = register_pernet_subsys(&iptable_nat_net_ops);
-	if (ret < 0) {
-		xt_unregister_template(&nf_nat_ipv4_table);
-		return ret;
-	}
+	ret = xt_register_template(&nf_nat_ipv4_table,
+				   iptable_nat_table_init);
+	if (ret < 0)
+		unregister_pernet_subsys(&iptable_nat_net_ops);
 
 	return ret;
 }
 
 static void __exit iptable_nat_exit(void)
 {
-	unregister_pernet_subsys(&iptable_nat_net_ops);
 	xt_unregister_template(&nf_nat_ipv4_table);
+	unregister_pernet_subsys(&iptable_nat_net_ops);
 }
 
 module_init(iptable_nat_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/nf_dup_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/nf_dup_ipv4.c
@@ -52,8 +52,9 @@
 {
 	struct iphdr *iph;
 
+	local_bh_disable();
 	if (this_cpu_read(nf_skb_duplicated))
-		return;
+		goto out;
 	/*
 	 * Copy the skb, and route the copy. Will later return %XT_CONTINUE for
 	 * the original skb, which should continue on its way as if nothing has
@@ -61,7 +62,7 @@
 	 */
 	skb = pskb_copy(skb, GFP_ATOMIC);
 	if (skb == NULL)
-		return;
+		goto out;
 
 #if IS_ENABLED(CONFIG_NF_CONNTRACK)
 	/* Avoid counting cloned packets towards the original connection. */
@@ -90,6 +91,8 @@
 	} else {
 		kfree_skb(skb);
 	}
+out:
+	local_bh_enable();
 }
 EXPORT_SYMBOL_GPL(nf_dup_ipv4);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/nf_reject_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/nf_reject_ipv4.c
@@ -62,7 +62,7 @@
 
 	skb_reserve(nskb, LL_MAX_HEADER);
 	niph = nf_reject_iphdr_put(nskb, oldskb, IPPROTO_TCP,
-				   net->ipv4.sysctl_ip_default_ttl);
+				   READ_ONCE(net->ipv4.sysctl_ip_default_ttl));
 	nf_reject_ip_tcphdr_put(nskb, oldskb, oth);
 	niph->tot_len = htons(nskb->len);
 	ip_send_check(niph);
@@ -115,7 +115,7 @@
 
 	skb_reserve(nskb, LL_MAX_HEADER);
 	niph = nf_reject_iphdr_put(nskb, oldskb, IPPROTO_ICMP,
-				   net->ipv4.sysctl_ip_default_ttl);
+				   READ_ONCE(net->ipv4.sysctl_ip_default_ttl));
 
 	skb_reset_transport_header(nskb);
 	icmph = skb_put_zero(nskb, sizeof(struct icmphdr));
@@ -278,6 +278,7 @@
 		goto free_nskb;
 
 	nf_ct_attach(nskb, oldskb);
+	nf_ct_set_closing(skb_nfct(oldskb));
 
 #if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
 	/* If we use ip_local_out for bridged traffic, the MAC source on
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/nf_tproxy_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/nf_tproxy_ipv4.c
@@ -38,7 +38,7 @@
 					    hp->source, lport ? lport : hp->dest,
 					    skb->dev, NF_TPROXY_LOOKUP_LISTENER);
 		if (sk2) {
-			inet_twsk_deschedule_put(inet_twsk(sk));
+			nf_tproxy_twsk_deschedule_put(inet_twsk(sk));
 			sk = sk2;
 		}
 	}
@@ -58,6 +58,8 @@
 
 	laddr = 0;
 	indev = __in_dev_get_rcu(skb->dev);
+	if (!indev)
+		return daddr;
 
 	in_dev_for_each_ifa_rcu(ifa, indev) {
 		if (ifa->ifa_flags & IFA_F_SECONDARY)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/netfilter/nft_fib_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/netfilter/nft_fib_ipv4.c
@@ -65,6 +65,8 @@
 	struct flowi4 fl4 = {
 		.flowi4_scope = RT_SCOPE_UNIVERSE,
 		.flowi4_iif = LOOPBACK_IFINDEX,
+		.flowi4_uid = sock_net_uid(nft_net(pkt), NULL),
+		.flowi4_l3mdev = l3mdev_master_ifindex_rcu(nft_in(pkt)),
 	};
 	const struct net_device *oif;
 	const struct net_device *found;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/nexthop.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/nexthop.c
@@ -675,9 +675,10 @@
 
 	p = nla_data(nla);
 	for (i = 0; i < nhg->num_nh; ++i) {
-		p->id = nhg->nh_entries[i].nh->id;
-		p->weight = nhg->nh_entries[i].weight - 1;
-		p += 1;
+		*p++ = (struct nexthop_grp) {
+			.id = nhg->nh_entries[i].nh->id,
+			.weight = nhg->nh_entries[i].weight - 1,
+		};
 	}
 
 	if (nhg->resilient && nla_put_nh_group_res(skb, nhg))
@@ -1857,7 +1858,7 @@
 		/* __ip6_del_rt does a release, so do a hold here */
 		fib6_info_hold(f6i);
 		ipv6_stub->ip6_del_rt(net, f6i,
-				      !net->ipv4.sysctl_nexthop_compat_mode);
+				      !READ_ONCE(net->ipv4.sysctl_nexthop_compat_mode));
 	}
 }
 
@@ -1899,15 +1900,36 @@
 /* if any FIB entries reference this nexthop, any dst entries
  * need to be regenerated
  */
-static void nh_rt_cache_flush(struct net *net, struct nexthop *nh)
+static void nh_rt_cache_flush(struct net *net, struct nexthop *nh,
+			      struct nexthop *replaced_nh)
 {
 	struct fib6_info *f6i;
+	struct nh_group *nhg;
+	int i;
 
 	if (!list_empty(&nh->fi_list))
 		rt_cache_flush(net);
 
 	list_for_each_entry(f6i, &nh->f6i_list, nh_list)
 		ipv6_stub->fib6_update_sernum(net, f6i);
+
+	/* if an IPv6 group was replaced, we have to release all old
+	 * dsts to make sure all refcounts are released
+	 */
+	if (!replaced_nh->is_group)
+		return;
+
+	/* new dsts must use only the new nexthop group */
+	synchronize_net();
+
+	nhg = rtnl_dereference(replaced_nh->nh_grp);
+	for (i = 0; i < nhg->num_nh; i++) {
+		struct nh_grp_entry *nhge = &nhg->nh_entries[i];
+		struct nh_info *nhi = rtnl_dereference(nhge->nh->nh_info);
+
+		if (nhi->family == AF_INET6)
+			ipv6_stub->fib6_nh_release_dsts(&nhi->fib6_nh);
+	}
 }
 
 static int replace_nexthop_grp(struct net *net, struct nexthop *old,
@@ -2247,7 +2269,7 @@
 		err = replace_nexthop_single(net, old, new, extack);
 
 	if (!err) {
-		nh_rt_cache_flush(net, old);
+		nh_rt_cache_flush(net, old, new);
 
 		__remove_nexthop(net, new, NULL);
 		nexthop_put(new);
@@ -2341,7 +2363,8 @@
 	if (!rc) {
 		nh_base_seq_inc(net);
 		nexthop_notify(RTM_NEWNEXTHOP, new_nh, &cfg->nlinfo);
-		if (replace_notify && net->ipv4.sysctl_nexthop_compat_mode)
+		if (replace_notify &&
+		    READ_ONCE(net->ipv4.sysctl_nexthop_compat_mode))
 			nexthop_replace_notify(net, new_nh, &cfg->nlinfo);
 	}
 
@@ -2513,7 +2536,7 @@
 	if (!err) {
 		nh->nh_flags = fib_nh->fib_nh_flags;
 		fib_info_update_nhc_saddr(net, &fib_nh->nh_common,
-					  fib_nh->fib_nh_scope);
+					  !fib_nh->fib_nh_scope ? 0 : fib_nh->fib_nh_scope - 1);
 	} else {
 		fib_nh_release(net, fib_nh);
 	}
@@ -2544,11 +2567,15 @@
 	/* sets nh_dev if successful */
 	err = ipv6_stub->fib6_nh_init(net, fib6_nh, &fib6_cfg, GFP_KERNEL,
 				      extack);
-	if (err)
+	if (err) {
+		/* IPv6 is not enabled, don't call fib6_nh_release */
+		if (err == -EAFNOSUPPORT)
+			goto out;
 		ipv6_stub->fib6_nh_release(fib6_nh);
-	else
+	} else {
 		nh->nh_flags = fib6_nh->fib_nh_flags;
-
+	}
+out:
 	return err;
 }
 
@@ -3196,13 +3223,9 @@
 				     &rtm_dump_nexthop_cb, &filter);
 	if (err < 0) {
 		if (likely(skb->len))
-			goto out;
-		goto out_err;
+			err = skb->len;
 	}
 
-out:
-	err = skb->len;
-out_err:
 	cb->seq = net->nexthop.seq;
 	nl_dump_check_consistent(cb, nlmsg_hdr(skb));
 	return err;
@@ -3342,25 +3365,19 @@
 		    dd->filter.res_bucket_nh_id != nhge->nh->id)
 			continue;
 
+		dd->ctx->bucket_index = bucket_index;
 		err = nh_fill_res_bucket(skb, nh, bucket, bucket_index,
 					 RTM_NEWNEXTHOPBUCKET, portid,
 					 cb->nlh->nlmsg_seq, NLM_F_MULTI,
 					 cb->extack);
-		if (err < 0) {
-			if (likely(skb->len))
-				goto out;
-			goto out_err;
-		}
+		if (err)
+			return err;
 	}
 
 	dd->ctx->done_nh_idx = dd->ctx->nh.idx + 1;
-	bucket_index = 0;
+	dd->ctx->bucket_index = 0;
 
-out:
-	err = skb->len;
-out_err:
-	dd->ctx->bucket_index = bucket_index;
-	return err;
+	return 0;
 }
 
 static int rtm_dump_nexthop_bucket_cb(struct sk_buff *skb,
@@ -3409,13 +3426,9 @@
 
 	if (err < 0) {
 		if (likely(skb->len))
-			goto out;
-		goto out_err;
+			err = skb->len;
 	}
 
-out:
-	err = skb->len;
-out_err:
 	cb->seq = net->nexthop.seq;
 	nl_dump_check_consistent(cb, nlmsg_hdr(skb));
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/ping.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/ping.c
@@ -172,16 +172,22 @@
 	struct sock *sk = NULL;
 	struct inet_sock *isk;
 	struct hlist_nulls_node *hnode;
-	int dif = skb->dev->ifindex;
+	int dif, sdif;
 
 	if (skb->protocol == htons(ETH_P_IP)) {
+		dif = inet_iif(skb);
+		sdif = inet_sdif(skb);
 		pr_debug("try to find: num = %d, daddr = %pI4, dif = %d\n",
 			 (int)ident, &ip_hdr(skb)->daddr, dif);
 #if IS_ENABLED(CONFIG_IPV6)
 	} else if (skb->protocol == htons(ETH_P_IPV6)) {
+		dif = inet6_iif(skb);
+		sdif = inet6_sdif(skb);
 		pr_debug("try to find: num = %d, daddr = %pI6c, dif = %d\n",
 			 (int)ident, &ipv6_hdr(skb)->daddr, dif);
 #endif
+	} else {
+		return NULL;
 	}
 
 	read_lock_bh(&ping_table.lock);
@@ -220,7 +226,8 @@
 			continue;
 		}
 
-		if (sk->sk_bound_dev_if && sk->sk_bound_dev_if != dif)
+		if (sk->sk_bound_dev_if && sk->sk_bound_dev_if != dif &&
+		    sk->sk_bound_dev_if != sdif)
 			continue;
 
 		sock_hold(sk);
@@ -298,6 +305,7 @@
 	struct net *net = sock_net(sk);
 	if (sk->sk_family == AF_INET) {
 		struct sockaddr_in *addr = (struct sockaddr_in *) uaddr;
+		u32 tb_id = RT_TABLE_LOCAL;
 		int chk_addr_ret;
 
 		if (addr_len < sizeof(*addr))
@@ -313,8 +321,10 @@
 
 		if (addr->sin_addr.s_addr == htonl(INADDR_ANY))
 			chk_addr_ret = RTN_LOCAL;
-		else
-			chk_addr_ret = inet_addr_type(net, addr->sin_addr.s_addr);
+		else {
+			tb_id = l3mdev_fib_table_by_index(net, sk->sk_bound_dev_if) ? : tb_id;
+			chk_addr_ret = inet_addr_type_table(net, addr->sin_addr.s_addr, tb_id);
+		}
 
 		if ((!inet_can_nonlocal_bind(net, isk) &&
 		     chk_addr_ret != RTN_LOCAL) ||
@@ -350,6 +360,14 @@
 			if (!dev) {
 				rcu_read_unlock();
 				return -ENODEV;
+			}
+		}
+
+		if (!dev && sk->sk_bound_dev_if) {
+			dev = dev_get_by_index_rcu(net, sk->sk_bound_dev_if);
+			if (!dev) {
+				rcu_read_unlock();
+				return -ENODEV;
 			}
 		}
 		has_addr = pingv6_ops.ipv6_chk_addr(net, &addr->sin6_addr, dev,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/proc.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/proc.c
@@ -53,7 +53,7 @@
 	struct net *net = seq->private;
 	int orphans, sockets;
 
-	orphans = percpu_counter_sum_positive(&tcp_orphan_count);
+	orphans = tcp_orphan_count_sum();
 	sockets = proto_sockets_allocated_sum_positive(&tcp_prot);
 
 	socket_seq_show(seq);
@@ -387,7 +387,7 @@
 
 	seq_printf(seq, "\nIp: %d %d",
 		   IPV4_DEVCONF_ALL(net, FORWARDING) ? 1 : 2,
-		   net->ipv4.sysctl_ip_default_ttl);
+		   READ_ONCE(net->ipv4.sysctl_ip_default_ttl));
 
 	BUILD_BUG_ON(offsetof(struct ipstats_mib, mibs) != 0);
 	snmp_get_cpu_field64_batch(buff64, snmp4_ipstats_list,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/raw.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/raw.c
@@ -99,8 +99,8 @@
 
 	write_lock_bh(&h->lock);
 	sk_add_node(sk, head);
-	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 	write_unlock_bh(&h->lock);
+	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 
 	return 0;
 }
@@ -559,6 +559,9 @@
 	}
 
 	ipcm_init_sk(&ipc, inet);
+	/* Keep backward compat */
+	if (hdrincl)
+		ipc.protocol = IPPROTO_RAW;
 
 	if (msg->msg_controllen) {
 		err = ip_cmsg_send(sk, msg, &ipc, false);
@@ -626,7 +629,7 @@
 
 	flowi4_init_output(&fl4, ipc.oif, ipc.sockc.mark, tos,
 			   RT_SCOPE_UNIVERSE,
-			   hdrincl ? IPPROTO_RAW : sk->sk_protocol,
+			   hdrincl ? ipc.protocol : sk->sk_protocol,
 			   inet_sk_flowi_flags(sk) |
 			    (hdrincl ? FLOWI_FLAG_KNOWN_NH : 0),
 			   daddr, saddr, 0, 0, sk->sk_uid);
@@ -721,6 +724,7 @@
 	int ret = -EINVAL;
 	int chk_addr_ret;
 
+	lock_sock(sk);
 	if (sk->sk_state != TCP_CLOSE || addr_len < sizeof(struct sockaddr_in))
 		goto out;
 
@@ -740,7 +744,9 @@
 		inet->inet_saddr = 0;  /* Use device */
 	sk_dst_reset(sk);
 	ret = 0;
-out:	return ret;
+out:
+	release_sock(sk);
+	return ret;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/route.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/route.c
@@ -118,14 +118,15 @@
 
 #define RT_GC_TIMEOUT (300*HZ)
 
+#define DEFAULT_MIN_PMTU (512 + 20 + 20)
+#define DEFAULT_MTU_EXPIRES (10 * 60 * HZ)
+
 static int ip_rt_max_size;
 static int ip_rt_redirect_number __read_mostly	= 9;
 static int ip_rt_redirect_load __read_mostly	= HZ / 50;
 static int ip_rt_redirect_silence __read_mostly	= ((HZ / 50) << (9 + 1));
 static int ip_rt_error_cost __read_mostly	= HZ;
 static int ip_rt_error_burst __read_mostly	= 5 * HZ;
-static int ip_rt_mtu_expires __read_mostly	= 10 * 60 * HZ;
-static u32 ip_rt_min_pmtu __read_mostly		= 512 + 20 + 20;
 static int ip_rt_min_advmss __read_mostly	= 256;
 
 static int ip_rt_gc_timeout __read_mostly	= RT_GC_TIMEOUT;
@@ -139,7 +140,8 @@
 static unsigned int	 ipv4_default_advmss(const struct dst_entry *dst);
 INDIRECT_CALLABLE_SCOPE
 unsigned int		ipv4_mtu(const struct dst_entry *dst);
-static struct dst_entry *ipv4_negative_advice(struct dst_entry *dst);
+static void		ipv4_negative_advice(struct sock *sk,
+					     struct dst_entry *dst);
 static void		 ipv4_link_failure(struct sk_buff *skb);
 static void		 ip_rt_update_pmtu(struct dst_entry *dst, struct sock *sk,
 					   struct sk_buff *skb, u32 mtu,
@@ -399,7 +401,13 @@
 
 static inline bool rt_is_expired(const struct rtable *rth)
 {
-	return rth->rt_genid != rt_genid_ipv4(dev_net(rth->dst.dev));
+	bool res;
+
+	rcu_read_lock();
+	res = rth->rt_genid != rt_genid_ipv4(dev_net_rcu(rth->dst.dev));
+	rcu_read_unlock();
+
+	return res;
 }
 
 void rt_cache_flush(struct net *net)
@@ -506,6 +514,15 @@
 }
 EXPORT_SYMBOL(__ip_select_ident);
 
+static void ip_rt_fix_tos(struct flowi4 *fl4)
+{
+	__u8 tos = RT_FL_TOS(fl4);
+
+	fl4->flowi4_tos = tos & IPTOS_RT_MASK;
+	fl4->flowi4_scope = tos & RTO_ONLINK ?
+			    RT_SCOPE_LINK : RT_SCOPE_UNIVERSE;
+}
+
 static void __build_flow_key(const struct net *net, struct flowi4 *fl4,
 			     const struct sock *sk,
 			     const struct iphdr *iph,
@@ -777,7 +794,7 @@
 			goto reject_redirect;
 	}
 
-	n = __ipv4_neigh_lookup(rt->dst.dev, new_gw);
+	n = __ipv4_neigh_lookup(rt->dst.dev, (__force u32)new_gw);
 	if (!n)
 		n = neigh_create(&arp_tbl, &new_gw, rt->dst.dev);
 	if (!IS_ERR(n)) {
@@ -831,25 +848,19 @@
 	rt = (struct rtable *) dst;
 
 	__build_flow_key(net, &fl4, sk, iph, oif, tos, prot, mark, 0);
+	ip_rt_fix_tos(&fl4);
 	__ip_do_redirect(rt, skb, &fl4, true);
 }
 
-static struct dst_entry *ipv4_negative_advice(struct dst_entry *dst)
+static void ipv4_negative_advice(struct sock *sk,
+				 struct dst_entry *dst)
 {
 	struct rtable *rt = (struct rtable *)dst;
-	struct dst_entry *ret = dst;
 
-	if (rt) {
-		if (dst->obsolete > 0) {
-			ip_rt_put(rt);
-			ret = NULL;
-		} else if ((rt->rt_flags & RTCF_REDIRECTED) ||
-			   rt->dst.expires) {
-			ip_rt_put(rt);
-			ret = NULL;
-		}
-	}
-	return ret;
+	if ((dst->obsolete > 0) ||
+	    (rt->rt_flags & RTCF_REDIRECTED) ||
+	    rt->dst.expires)
+		sk_dst_reset(sk);
 }
 
 /*
@@ -923,13 +934,11 @@
 		icmp_send(skb, ICMP_REDIRECT, ICMP_REDIR_HOST, gw);
 		peer->rate_last = jiffies;
 		++peer->n_redirects;
-#ifdef CONFIG_IP_ROUTE_VERBOSE
-		if (log_martians &&
+		if (IS_ENABLED(CONFIG_IP_ROUTE_VERBOSE) && log_martians &&
 		    peer->n_redirects == ip_rt_redirect_number)
 			net_warn_ratelimited("host %pI4/if%d ignores redirects for %pI4 to %pI4\n",
 					     &ip_hdr(skb)->saddr, inet_iif(skb),
 					     &ip_hdr(skb)->daddr, &gw);
-#endif
 	}
 out_put_peer:
 	inet_putpeer(peer);
@@ -1014,9 +1023,9 @@
 static void __ip_rt_update_pmtu(struct rtable *rt, struct flowi4 *fl4, u32 mtu)
 {
 	struct dst_entry *dst = &rt->dst;
-	struct net *net = dev_net(dst->dev);
 	struct fib_result res;
 	bool lock = false;
+	struct net *net;
 	u32 old_mtu;
 
 	if (ip_mtu_locked(dst))
@@ -1026,24 +1035,38 @@
 	if (old_mtu < mtu)
 		return;
 
-	if (mtu < ip_rt_min_pmtu) {
+	rcu_read_lock();
+	net = dev_net_rcu(dst->dev);
+	if (mtu < net->ipv4.ip_rt_min_pmtu) {
 		lock = true;
-		mtu = min(old_mtu, ip_rt_min_pmtu);
+		mtu = min(old_mtu, net->ipv4.ip_rt_min_pmtu);
 	}
 
 	if (rt->rt_pmtu == mtu && !lock &&
-	    time_before(jiffies, dst->expires - ip_rt_mtu_expires / 2))
-		return;
+	    time_before(jiffies, dst->expires - net->ipv4.ip_rt_mtu_expires / 2))
+		goto out;
 
-	rcu_read_lock();
 	if (fib_lookup(net, fl4, &res, 0) == 0) {
 		struct fib_nh_common *nhc;
 
 		fib_select_path(net, &res, fl4, NULL);
+#ifdef CONFIG_IP_ROUTE_MULTIPATH
+		if (fib_info_num_path(res.fi) > 1) {
+			int nhsel;
+
+			for (nhsel = 0; nhsel < fib_info_num_path(res.fi); nhsel++) {
+				nhc = fib_info_nhc(res.fi, nhsel);
+				update_or_create_fnhe(nhc, fl4->daddr, 0, mtu, lock,
+						      jiffies + net->ipv4.ip_rt_mtu_expires);
+			}
+			goto out;
+		}
+#endif /* CONFIG_IP_ROUTE_MULTIPATH */
 		nhc = FIB_RES_NHC(res);
 		update_or_create_fnhe(nhc, fl4->daddr, 0, mtu, lock,
-				      jiffies + ip_rt_mtu_expires);
+				      jiffies + net->ipv4.ip_rt_mtu_expires);
 	}
+out:
 	rcu_read_unlock();
 }
 
@@ -1055,6 +1078,7 @@
 	struct flowi4 fl4;
 
 	ip_rt_build_flow_key(&fl4, sk, skb);
+	ip_rt_fix_tos(&fl4);
 
 	/* Don't make lookup fail for bridged encapsulations */
 	if (skb && netif_is_any_bridge_port(skb->dev))
@@ -1129,6 +1153,8 @@
 			goto out;
 
 		new = true;
+	} else {
+		ip_rt_fix_tos(&fl4);
 	}
 
 	__ip_rt_update_pmtu((struct rtable *)xfrm_dst_path(&rt->dst), &fl4, mtu);
@@ -1207,6 +1233,7 @@
 
 static void ipv4_send_dest_unreach(struct sk_buff *skb)
 {
+	struct net_device *dev;
 	struct ip_options opt;
 	int res;
 
@@ -1224,7 +1251,8 @@
 		opt.optlen = ip_hdr(skb)->ihl * 4 - sizeof(struct iphdr);
 
 		rcu_read_lock();
-		res = __ip_options_compile(dev_net(skb->dev), &opt, skb, NULL);
+		dev = skb->dev ? skb->dev : skb_rtable(skb)->dst.dev;
+		res = __ip_options_compile(dev_net(dev), &opt, skb, NULL);
 		rcu_read_unlock();
 
 		if (res)
@@ -1275,7 +1303,7 @@
 		struct flowi4 fl4 = {
 			.daddr = iph->daddr,
 			.saddr = iph->saddr,
-			.flowi4_tos = RT_TOS(iph->tos),
+			.flowi4_tos = iph->tos & IPTOS_RT_MASK,
 			.flowi4_oif = rt->dst.dev->ifindex,
 			.flowi4_iif = skb->dev->ifindex,
 			.flowi4_mark = skb->mark,
@@ -1391,7 +1419,7 @@
 	struct fib_info *fi = res->fi;
 	u32 mtu = 0;
 
-	if (dev_net(dev)->ipv4.sysctl_ip_fwd_use_pmtu ||
+	if (READ_ONCE(dev_net(dev)->ipv4.sysctl_ip_fwd_use_pmtu) ||
 	    fi->fib_metrics->metrics[RTAX_LOCK - 1] & (1 << RTAX_MTU))
 		mtu = fi->fib_mtu;
 
@@ -1714,6 +1742,7 @@
 	struct in_device *in_dev = __in_dev_get_rcu(dev);
 	unsigned int flags = RTCF_MULTICAST;
 	struct rtable *rth;
+	bool no_policy;
 	u32 itag = 0;
 	int err;
 
@@ -1724,8 +1753,12 @@
 	if (our)
 		flags |= RTCF_LOCAL;
 
+	no_policy = IN_DEV_ORCONF(in_dev, NOPOLICY);
+	if (no_policy)
+		IPCB(skb)->flags |= IPSKB_NOPOLICY;
+
 	rth = rt_dst_alloc(dev_net(dev)->loopback_dev, flags, RTN_MULTICAST,
-			   IN_DEV_ORCONF(in_dev, NOPOLICY), false);
+			   no_policy, false);
 	if (!rth)
 		return -ENOBUFS;
 
@@ -1741,6 +1774,7 @@
 #endif
 	RT_CACHE_STAT_INC(in_slow_mc);
 
+	skb_dst_drop(skb);
 	skb_dst_set(skb, &rth->dst);
 	return 0;
 }
@@ -1783,7 +1817,7 @@
 	struct rtable *rth;
 	int err;
 	struct in_device *out_dev;
-	bool do_cache;
+	bool do_cache, no_policy;
 	u32 itag = 0;
 
 	/* get a working reference to the output device */
@@ -1828,6 +1862,10 @@
 		}
 	}
 
+	no_policy = IN_DEV_ORCONF(in_dev, NOPOLICY);
+	if (no_policy)
+		IPCB(skb)->flags |= IPSKB_NOPOLICY;
+
 	fnhe = find_exception(nhc, daddr);
 	if (do_cache) {
 		if (fnhe)
@@ -1840,8 +1878,7 @@
 		}
 	}
 
-	rth = rt_dst_alloc(out_dev->dev, 0, res->type,
-			   IN_DEV_ORCONF(in_dev, NOPOLICY),
+	rth = rt_dst_alloc(out_dev->dev, 0, res->type, no_policy,
 			   IN_DEV_ORCONF(out_dev, NOXFRM));
 	if (!rth) {
 		err = -ENOBUFS;
@@ -1907,7 +1944,7 @@
 					   const struct sk_buff *skb,
 					   bool *p_has_inner)
 {
-	u32 hash_fields = net->ipv4.sysctl_fib_multipath_hash_fields;
+	u32 hash_fields = READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_fields);
 	struct flow_keys keys, hash_keys;
 
 	if (!(hash_fields & FIB_MULTIPATH_HASH_FIELD_OUTER_MASK))
@@ -1936,7 +1973,7 @@
 					   const struct sk_buff *skb,
 					   bool has_inner)
 {
-	u32 hash_fields = net->ipv4.sysctl_fib_multipath_hash_fields;
+	u32 hash_fields = READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_fields);
 	struct flow_keys keys, hash_keys;
 
 	/* We assume the packet carries an encapsulation, but if none was
@@ -1996,7 +2033,7 @@
 static u32 fib_multipath_custom_hash_fl4(const struct net *net,
 					 const struct flowi4 *fl4)
 {
-	u32 hash_fields = net->ipv4.sysctl_fib_multipath_hash_fields;
+	u32 hash_fields = READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_fields);
 	struct flow_keys hash_keys;
 
 	if (!(hash_fields & FIB_MULTIPATH_HASH_FIELD_OUTER_MASK))
@@ -2026,7 +2063,7 @@
 	struct flow_keys hash_keys;
 	u32 mhash = 0;
 
-	switch (net->ipv4.sysctl_fib_multipath_hash_policy) {
+	switch (READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_policy)) {
 	case 0:
 		memset(&hash_keys, 0, sizeof(hash_keys));
 		hash_keys.control.addr_type = FLOW_DISSECTOR_KEY_IPV4_ADDRS;
@@ -2129,6 +2166,7 @@
 		int h = fib_multipath_hash(res->fi->fib_net, NULL, skb, hkeys);
 
 		fib_select_multipath(res, h);
+		IPCB(skb)->flags |= IPSKB_MULTIPATH;
 	}
 #endif
 
@@ -2150,6 +2188,9 @@
 	int err = -EINVAL;
 	u32 tag = 0;
 
+	if (!in_dev)
+		return -EINVAL;
+
 	if (ipv4_is_multicast(saddr) || ipv4_is_lbcast(saddr))
 		goto martian_source;
 
@@ -2216,6 +2257,7 @@
 	struct rtable	*rth;
 	struct flowi4	fl4;
 	bool do_cache = true;
+	bool no_policy;
 
 	/* IP on this device is disabled. */
 
@@ -2264,6 +2306,7 @@
 	/*
 	 *	Now we are ready to route packet.
 	 */
+	fl4.flowi4_l3mdev = 0;
 	fl4.flowi4_oif = 0;
 	fl4.flowi4_iif = dev->ifindex;
 	fl4.flowi4_mark = skb->mark;
@@ -2333,6 +2376,10 @@
 	RT_CACHE_STAT_INC(in_brd);
 
 local_input:
+	no_policy = IN_DEV_ORCONF(in_dev, NOPOLICY);
+	if (no_policy)
+		IPCB(skb)->flags |= IPSKB_NOPOLICY;
+
 	do_cache &= res->fi && !itag;
 	if (do_cache) {
 		struct fib_nh_common *nhc = FIB_RES_NHC(*res);
@@ -2347,7 +2394,7 @@
 
 	rth = rt_dst_alloc(ip_rt_get_dev(net, res),
 			   flags | RTCF_LOCAL, res->type,
-			   IN_DEV_ORCONF(in_dev, NOPOLICY), false);
+			   no_policy, false);
 	if (!rth)
 		goto e_nobufs;
 
@@ -2609,7 +2656,6 @@
 struct rtable *ip_route_output_key_hash(struct net *net, struct flowi4 *fl4,
 					const struct sk_buff *skb)
 {
-	__u8 tos = RT_FL_TOS(fl4);
 	struct fib_result res = {
 		.type		= RTN_UNSPEC,
 		.fi		= NULL,
@@ -2619,9 +2665,7 @@
 	struct rtable *rth;
 
 	fl4->flowi4_iif = LOOPBACK_IFINDEX;
-	fl4->flowi4_tos = tos & IPTOS_RT_MASK;
-	fl4->flowi4_scope = ((tos & RTO_ONLINK) ?
-			 RT_SCOPE_LINK : RT_SCOPE_UNIVERSE);
+	ip_rt_fix_tos(fl4);
 
 	rcu_read_lock();
 	rth = ip_route_output_key_hash_rcu(net, fl4, &res, skb);
@@ -2739,8 +2783,7 @@
 		res->fi = NULL;
 		res->table = NULL;
 		if (fl4->flowi4_oif &&
-		    (ipv4_is_multicast(fl4->daddr) ||
-		    !netif_index_is_l3_master(net, fl4->flowi4_oif))) {
+		    (ipv4_is_multicast(fl4->daddr) || !fl4->flowi4_l3mdev)) {
 			/* Apparently, routing tables are wrong. Assume,
 			 * that the destination is on link.
 			 *
@@ -3401,8 +3444,10 @@
 				    fa->fa_tos == fri.tos &&
 				    fa->fa_info == res.fi &&
 				    fa->fa_type == fri.type) {
-					fri.offload = fa->offload;
-					fri.trap = fa->trap;
+					fri.offload = READ_ONCE(fa->offload);
+					fri.trap = READ_ONCE(fa->trap);
+					fri.offload_failed =
+						READ_ONCE(fa->offload_failed);
 					break;
 				}
 			}
@@ -3542,21 +3587,6 @@
 		.proc_handler	= proc_dointvec,
 	},
 	{
-		.procname	= "mtu_expires",
-		.data		= &ip_rt_mtu_expires,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_jiffies,
-	},
-	{
-		.procname	= "min_pmtu",
-		.data		= &ip_rt_min_pmtu,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &ip_min_valid_pmtu,
-	},
-	{
 		.procname	= "min_adv_mss",
 		.data		= &ip_rt_min_advmss,
 		.maxlen		= sizeof(int),
@@ -3568,13 +3598,28 @@
 
 static const char ipv4_route_flush_procname[] = "flush";
 
-static struct ctl_table ipv4_route_flush_table[] = {
+static struct ctl_table ipv4_route_netns_table[] = {
 	{
 		.procname	= ipv4_route_flush_procname,
 		.maxlen		= sizeof(int),
 		.mode		= 0200,
 		.proc_handler	= ipv4_sysctl_rtcache_flush,
 	},
+	{
+		.procname       = "min_pmtu",
+		.data           = &init_net.ipv4.ip_rt_min_pmtu,
+		.maxlen         = sizeof(int),
+		.mode           = 0644,
+		.proc_handler   = proc_dointvec_minmax,
+		.extra1         = &ip_min_valid_pmtu,
+	},
+	{
+		.procname       = "mtu_expires",
+		.data           = &init_net.ipv4.ip_rt_mtu_expires,
+		.maxlen         = sizeof(int),
+		.mode           = 0644,
+		.proc_handler   = proc_dointvec_jiffies,
+	},
 	{ },
 };
 
@@ -3582,9 +3627,11 @@
 {
 	struct ctl_table *tbl;
 
-	tbl = ipv4_route_flush_table;
+	tbl = ipv4_route_netns_table;
 	if (!net_eq(net, &init_net)) {
-		tbl = kmemdup(tbl, sizeof(ipv4_route_flush_table), GFP_KERNEL);
+		int i;
+
+		tbl = kmemdup(tbl, sizeof(ipv4_route_netns_table), GFP_KERNEL);
 		if (!tbl)
 			goto err_dup;
 
@@ -3593,6 +3640,12 @@
 			if (tbl[0].procname != ipv4_route_flush_procname)
 				tbl[0].procname = NULL;
 		}
+
+		/* Update the variables to point into the current struct net
+		 * except for the first element flush
+		 */
+		for (i = 1; i < ARRAY_SIZE(ipv4_route_netns_table) - 1; i++)
+			tbl[i].data += (void *)net - (void *)&init_net;
 	}
 	tbl[0].extra1 = net;
 
@@ -3602,7 +3655,7 @@
 	return 0;
 
 err_reg:
-	if (tbl != ipv4_route_flush_table)
+	if (tbl != ipv4_route_netns_table)
 		kfree(tbl);
 err_dup:
 	return -ENOMEM;
@@ -3614,7 +3667,7 @@
 
 	tbl = net->ipv4.route_hdr->ctl_table_arg;
 	unregister_net_sysctl_table(net->ipv4.route_hdr);
-	BUG_ON(tbl == ipv4_route_flush_table);
+	BUG_ON(tbl == ipv4_route_netns_table);
 	kfree(tbl);
 }
 
@@ -3624,6 +3677,18 @@
 };
 #endif
 
+static __net_init int netns_ip_rt_init(struct net *net)
+{
+	/* Set default value for namespaceified sysctls */
+	net->ipv4.ip_rt_min_pmtu = DEFAULT_MIN_PMTU;
+	net->ipv4.ip_rt_mtu_expires = DEFAULT_MTU_EXPIRES;
+	return 0;
+}
+
+static struct pernet_operations __net_initdata ip_rt_ops = {
+	.init = netns_ip_rt_init,
+};
+
 static __net_init int rt_genid_init(struct net *net)
 {
 	atomic_set(&net->ipv4.rt_genid, 0);
@@ -3729,6 +3794,7 @@
 #ifdef CONFIG_SYSCTL
 	register_pernet_subsys(&sysctl_route_ops);
 #endif
+	register_pernet_subsys(&ip_rt_ops);
 	register_pernet_subsys(&rt_genid_ops);
 	register_pernet_subsys(&ipv4_inetpeer_ops);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/syncookies.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/syncookies.c
@@ -43,7 +43,6 @@
  * requested/supported by the syn/synack exchange.
  */
 #define TSBITS	6
-#define TSMASK	(((__u32)1 << TSBITS) - 1)
 
 static u32 cookie_hash(__be32 saddr, __be32 daddr, __be16 sport, __be16 dport,
 		       u32 count, int c)
@@ -64,27 +63,22 @@
  */
 u64 cookie_init_timestamp(struct request_sock *req, u64 now)
 {
-	struct inet_request_sock *ireq;
-	u32 ts, ts_now = tcp_ns_to_ts(now);
+	const struct inet_request_sock *ireq = inet_rsk(req);
+	u64 ts, ts_now = tcp_ns_to_ts(now);
 	u32 options = 0;
 
-	ireq = inet_rsk(req);
-
 	options = ireq->wscale_ok ? ireq->snd_wscale : TS_OPT_WSCALE_MASK;
 	if (ireq->sack_ok)
 		options |= TS_OPT_SACK;
 	if (ireq->ecn_ok)
 		options |= TS_OPT_ECN;
 
-	ts = ts_now & ~TSMASK;
+	ts = (ts_now >> TSBITS) << TSBITS;
 	ts |= options;
-	if (ts > ts_now) {
-		ts >>= TSBITS;
-		ts--;
-		ts <<= TSBITS;
-		ts |= options;
-	}
-	return (u64)ts * (NSEC_PER_SEC / TCP_TS_HZ);
+	if (ts > ts_now)
+		ts -= (1UL << TSBITS);
+
+	return ts * (NSEC_PER_SEC / TCP_TS_HZ);
 }
 
 
@@ -249,12 +243,12 @@
 		return true;
 	}
 
-	if (!net->ipv4.sysctl_tcp_timestamps)
+	if (!READ_ONCE(net->ipv4.sysctl_tcp_timestamps))
 		return false;
 
 	tcp_opt->sack_ok = (options & TS_OPT_SACK) ? TCP_SACK_SEEN : 0;
 
-	if (tcp_opt->sack_ok && !net->ipv4.sysctl_tcp_sack)
+	if (tcp_opt->sack_ok && !READ_ONCE(net->ipv4.sysctl_tcp_sack))
 		return false;
 
 	if ((options & TS_OPT_WSCALE_MASK) == TS_OPT_WSCALE_MASK)
@@ -263,7 +257,7 @@
 	tcp_opt->wscale_ok = 1;
 	tcp_opt->snd_wscale = options & TS_OPT_WSCALE_MASK;
 
-	return net->ipv4.sysctl_tcp_window_scaling != 0;
+	return READ_ONCE(net->ipv4.sysctl_tcp_window_scaling) != 0;
 }
 EXPORT_SYMBOL(cookie_timestamp_decode);
 
@@ -275,7 +269,7 @@
 	if (!ecn_ok)
 		return false;
 
-	if (net->ipv4.sysctl_tcp_ecn)
+	if (READ_ONCE(net->ipv4.sysctl_tcp_ecn))
 		return true;
 
 	return dst_feature(dst, RTAX_FEATURE_ECN);
@@ -283,22 +277,26 @@
 EXPORT_SYMBOL(cookie_ecn_ok);
 
 struct request_sock *cookie_tcp_reqsk_alloc(const struct request_sock_ops *ops,
+					    const struct tcp_request_sock_ops *af_ops,
 					    struct sock *sk,
 					    struct sk_buff *skb)
 {
 	struct tcp_request_sock *treq;
 	struct request_sock *req;
 
-#ifdef CONFIG_MPTCP
 	if (sk_is_mptcp(sk))
-		ops = &mptcp_subflow_request_sock_ops;
-#endif
+		req = mptcp_subflow_reqsk_alloc(ops, sk, false);
+	else
+		req = inet_reqsk_alloc(ops, sk, false);
 
-	req = inet_reqsk_alloc(ops, sk, false);
 	if (!req)
 		return NULL;
 
 	treq = tcp_rsk(req);
+
+	/* treq->af_specific might be used to perform TCP_MD5 lookup */
+	treq->af_specific = af_ops;
+
 	treq->syn_tos = TCP_SKB_CB(skb)->ip_dsfield;
 #if IS_ENABLED(CONFIG_MPTCP)
 	treq->is_mptcp = sk_is_mptcp(sk);
@@ -337,7 +335,8 @@
 	struct flowi4 fl4;
 	u32 tsoff = 0;
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_syncookies || !th->ack || th->rst)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_syncookies) ||
+	    !th->ack || th->rst)
 		goto out;
 
 	if (tcp_synq_no_recent_overflow(sk))
@@ -366,7 +365,8 @@
 		goto out;
 
 	ret = NULL;
-	req = cookie_tcp_reqsk_alloc(&tcp_request_sock_ops, sk, skb);
+	req = cookie_tcp_reqsk_alloc(&tcp_request_sock_ops,
+				     &tcp_request_sock_ipv4_ops, sk, skb);
 	if (!req)
 		goto out;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/sysctl_net_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/sysctl_net_ipv4.c
@@ -38,6 +38,7 @@
 static int ip_local_port_range_max[] = { 65535, 65535 };
 static int tcp_adv_win_scale_min = -31;
 static int tcp_adv_win_scale_max = 31;
+static int tcp_app_win_max = 31;
 static int tcp_min_snd_mss_min = TCP_MIN_SND_MSS;
 static int tcp_min_snd_mss_max = 65535;
 static int ip_privileged_port_min;
@@ -97,7 +98,7 @@
 		 * port limit.
 		 */
 		if ((range[1] < range[0]) ||
-		    (range[0] < net->ipv4.sysctl_ip_prot_sock))
+		    (range[0] < READ_ONCE(net->ipv4.sysctl_ip_prot_sock)))
 			ret = -EINVAL;
 		else
 			set_local_port_range(net, range);
@@ -123,7 +124,7 @@
 		.extra2 = &ip_privileged_port_max,
 	};
 
-	pports = net->ipv4.sysctl_ip_prot_sock;
+	pports = READ_ONCE(net->ipv4.sysctl_ip_prot_sock);
 
 	ret = proc_dointvec_minmax(&tmp, write, buffer, lenp, ppos);
 
@@ -135,7 +136,7 @@
 		if (range[0] < pports)
 			ret = -EINVAL;
 		else
-			net->ipv4.sysctl_ip_prot_sock = pports;
+			WRITE_ONCE(net->ipv4.sysctl_ip_prot_sock, pports);
 	}
 
 	return ret;
@@ -363,61 +364,6 @@
 	return ret;
 }
 
-static void proc_configure_early_demux(int enabled, int protocol)
-{
-	struct net_protocol *ipprot;
-#if IS_ENABLED(CONFIG_IPV6)
-	struct inet6_protocol *ip6prot;
-#endif
-
-	rcu_read_lock();
-
-	ipprot = rcu_dereference(inet_protos[protocol]);
-	if (ipprot)
-		ipprot->early_demux = enabled ? ipprot->early_demux_handler :
-						NULL;
-
-#if IS_ENABLED(CONFIG_IPV6)
-	ip6prot = rcu_dereference(inet6_protos[protocol]);
-	if (ip6prot)
-		ip6prot->early_demux = enabled ? ip6prot->early_demux_handler :
-						 NULL;
-#endif
-	rcu_read_unlock();
-}
-
-static int proc_tcp_early_demux(struct ctl_table *table, int write,
-				void *buffer, size_t *lenp, loff_t *ppos)
-{
-	int ret = 0;
-
-	ret = proc_dou8vec_minmax(table, write, buffer, lenp, ppos);
-
-	if (write && !ret) {
-		int enabled = init_net.ipv4.sysctl_tcp_early_demux;
-
-		proc_configure_early_demux(enabled, IPPROTO_TCP);
-	}
-
-	return ret;
-}
-
-static int proc_udp_early_demux(struct ctl_table *table, int write,
-				void *buffer, size_t *lenp, loff_t *ppos)
-{
-	int ret = 0;
-
-	ret = proc_dou8vec_minmax(table, write, buffer, lenp, ppos);
-
-	if (write && !ret) {
-		int enabled = init_net.ipv4.sysctl_udp_early_demux;
-
-		proc_configure_early_demux(enabled, IPPROTO_UDP);
-	}
-
-	return ret;
-}
-
 static int proc_tfo_blackhole_detect_timeout(struct ctl_table *table,
 					     int write, void *buffer,
 					     size_t *lenp, loff_t *ppos)
@@ -639,6 +585,8 @@
 		.maxlen		= sizeof(u8),
 		.mode		= 0644,
 		.proc_handler	= proc_dou8vec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE
 	},
 	{
 		.procname	= "icmp_errors_use_inbound_ifaddr",
@@ -646,6 +594,8 @@
 		.maxlen		= sizeof(u8),
 		.mode		= 0644,
 		.proc_handler	= proc_dou8vec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE
 	},
 	{
 		.procname	= "icmp_ratelimit",
@@ -685,6 +635,8 @@
 		.maxlen		= sizeof(u8),
 		.mode		= 0644,
 		.proc_handler	= proc_dou8vec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_TWO,
 	},
 	{
 		.procname	= "tcp_ecn_fallback",
@@ -692,6 +644,8 @@
 		.maxlen		= sizeof(u8),
 		.mode		= 0644,
 		.proc_handler	= proc_dou8vec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE,
 	},
 	{
 		.procname	= "ip_dynaddr",
@@ -712,14 +666,14 @@
 		.data           = &init_net.ipv4.sysctl_udp_early_demux,
 		.maxlen         = sizeof(u8),
 		.mode           = 0644,
-		.proc_handler   = proc_udp_early_demux
+		.proc_handler   = proc_dou8vec_minmax,
 	},
 	{
 		.procname       = "tcp_early_demux",
 		.data           = &init_net.ipv4.sysctl_tcp_early_demux,
 		.maxlen         = sizeof(u8),
 		.mode           = 0644,
-		.proc_handler   = proc_tcp_early_demux
+		.proc_handler   = proc_dou8vec_minmax,
 	},
 	{
 		.procname       = "nexthop_compat_mode",
@@ -1215,6 +1169,8 @@
 		.maxlen		= sizeof(u8),
 		.mode		= 0644,
 		.proc_handler	= proc_dou8vec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= &tcp_app_win_max,
 	},
 	{
 		.procname	= "tcp_adv_win_scale",
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp.c
@@ -287,8 +287,8 @@
 	TCP_CMSG_TS = 2
 };
 
-struct percpu_counter tcp_orphan_count;
-EXPORT_SYMBOL_GPL(tcp_orphan_count);
+DEFINE_PER_CPU(unsigned int, tcp_orphan_count);
+EXPORT_PER_CPU_SYMBOL_GPL(tcp_orphan_count);
 
 long sysctl_tcp_mem[3] __read_mostly;
 EXPORT_SYMBOL(sysctl_tcp_mem);
@@ -435,10 +435,11 @@
 	 * algorithms that we must have the following bandaid to talk
 	 * efficiently to them.  -DaveM
 	 */
-	tp->snd_cwnd = TCP_INIT_CWND;
+	tcp_snd_cwnd_set(tp, TCP_INIT_CWND);
 
 	/* There's a bubble in the pipe until at least the first ACK. */
 	tp->app_limited = ~0U;
+	tp->rate_app_limited = 1;
 
 	/* See draft-stevens-tcpca-spec-01 for discussion of the
 	 * initialization of these values.
@@ -447,7 +448,7 @@
 	tp->snd_cwnd_clamp = ~0;
 	tp->mss_cache = TCP_MSS_DEFAULT;
 
-	tp->reordering = sock_net(sk)->ipv4.sysctl_tcp_reordering;
+	tp->reordering = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_reordering);
 	tcp_assign_congestion_control(sk);
 
 	tp->tsoffset = 0;
@@ -458,8 +459,8 @@
 
 	icsk->icsk_sync_mss = tcp_sync_mss;
 
-	WRITE_ONCE(sk->sk_sndbuf, sock_net(sk)->ipv4.sysctl_tcp_wmem[1]);
-	WRITE_ONCE(sk->sk_rcvbuf, sock_net(sk)->ipv4.sysctl_tcp_rmem[1]);
+	WRITE_ONCE(sk->sk_sndbuf, READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_wmem[1]));
+	WRITE_ONCE(sk->sk_rcvbuf, READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[1]));
 
 	sk_sockets_allocated_inc(sk);
 	sk->sk_route_forced_caps = NETIF_F_GSO;
@@ -501,6 +502,7 @@
 	__poll_t mask;
 	struct sock *sk = sock->sk;
 	const struct tcp_sock *tp = tcp_sk(sk);
+	u8 shutdown;
 	int state;
 
 	sock_poll_wait(file, sock, wait);
@@ -543,9 +545,10 @@
 	 * NOTE. Check for TCP_CLOSE is added. The goal is to prevent
 	 * blocking on fresh not-connected or disconnected socket. --ANK
 	 */
-	if (sk->sk_shutdown == SHUTDOWN_MASK || state == TCP_CLOSE)
+	shutdown = READ_ONCE(sk->sk_shutdown);
+	if (shutdown == SHUTDOWN_MASK || state == TCP_CLOSE)
 		mask |= EPOLLHUP;
-	if (sk->sk_shutdown & RCV_SHUTDOWN)
+	if (shutdown & RCV_SHUTDOWN)
 		mask |= EPOLLIN | EPOLLRDNORM | EPOLLRDHUP;
 
 	/* Connected or passive Fast Open socket? */
@@ -561,7 +564,7 @@
 		if (tcp_stream_is_readable(sk, target))
 			mask |= EPOLLIN | EPOLLRDNORM;
 
-		if (!(sk->sk_shutdown & SEND_SHUTDOWN)) {
+		if (!(shutdown & SEND_SHUTDOWN)) {
 			if (__sk_stream_is_writeable(sk, 1)) {
 				mask |= EPOLLOUT | EPOLLWRNORM;
 			} else {  /* send SIGIO later */
@@ -589,9 +592,10 @@
 		 */
 		mask |= EPOLLOUT | EPOLLWRNORM;
 	}
-	/* This barrier is coupled with smp_wmb() in tcp_reset() */
+	/* This barrier is coupled with smp_wmb() in tcp_done_with_error() */
 	smp_rmb();
-	if (sk->sk_err || !skb_queue_empty_lockless(&sk->sk_error_queue))
+	if (READ_ONCE(sk->sk_err) ||
+	    !skb_queue_empty_lockless(&sk->sk_error_queue))
 		mask |= EPOLLERR;
 
 	return mask;
@@ -644,7 +648,7 @@
 }
 EXPORT_SYMBOL(tcp_ioctl);
 
-static inline void tcp_mark_push(struct tcp_sock *tp, struct sk_buff *skb)
+void tcp_mark_push(struct tcp_sock *tp, struct sk_buff *skb)
 {
 	TCP_SKB_CB(skb)->tcp_flags |= TCPHDR_PSH;
 	tp->pushed_seq = tp->write_seq;
@@ -655,7 +659,7 @@
 	return after(tp->write_seq, tp->pushed_seq + (tp->max_window >> 1));
 }
 
-static void skb_entail(struct sock *sk, struct sk_buff *skb)
+void tcp_skb_entail(struct sock *sk, struct sk_buff *skb)
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct tcp_skb_cb *tcb = TCP_SKB_CB(skb);
@@ -694,7 +698,7 @@
 				int size_goal)
 {
 	return skb->len < size_goal &&
-	       sock_net(sk)->ipv4.sysctl_tcp_autocorking &&
+	       READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_autocorking) &&
 	       !tcp_rtx_queue_empty(sk) &&
 	       refcount_read(&sk->sk_wmem_alloc) > skb->truesize;
 }
@@ -719,6 +723,7 @@
 		if (!test_bit(TSQ_THROTTLED, &sk->sk_tsq_flags)) {
 			NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPAUTOCORKING);
 			set_bit(TSQ_THROTTLED, &sk->sk_tsq_flags);
+			smp_mb__after_atomic();
 		}
 		/* It is possible TX completion already happened
 		 * before we set TSQ_THROTTLED.
@@ -950,9 +955,11 @@
  * importantly be able to generate EPOLLOUT for Edge Trigger epoll()
  * users.
  */
-void tcp_remove_empty_skb(struct sock *sk, struct sk_buff *skb)
+void tcp_remove_empty_skb(struct sock *sk)
 {
-	if (skb && !skb->len) {
+	struct sk_buff *skb = tcp_write_queue_tail(sk);
+
+	if (skb && TCP_SKB_CB(skb)->seq == TCP_SKB_CB(skb)->end_seq) {
 		tcp_unlink_write_queue(skb, sk);
 		if (tcp_write_queue_empty(sk))
 			tcp_chrono_stop(sk, TCP_CHRONO_BUSY);
@@ -982,7 +989,7 @@
 #ifdef CONFIG_TLS_DEVICE
 		skb->decrypted = !!(flags & MSG_SENDPAGE_DECRYPTED);
 #endif
-		skb_entail(sk, skb);
+		tcp_skb_entail(sk, skb);
 		copy = size_goal;
 	}
 
@@ -991,7 +998,7 @@
 
 	i = skb_shinfo(skb)->nr_frags;
 	can_coalesce = skb_can_coalesce(skb, i, page, offset);
-	if (!can_coalesce && i >= sysctl_max_skb_frags) {
+	if (!can_coalesce && i >= READ_ONCE(sysctl_max_skb_frags)) {
 		tcp_mark_push(tp, skb);
 		goto new_segment;
 	}
@@ -1002,7 +1009,7 @@
 		skb_frag_size_add(&skb_shinfo(skb)->frags[i - 1], copy);
 	} else {
 		get_page(page);
-		skb_fill_page_desc(skb, i, page, offset, copy);
+		skb_fill_page_desc_noacc(skb, i, page, offset, copy);
 	}
 
 	if (!(flags & MSG_NO_SHARED_FRAGS))
@@ -1104,7 +1111,7 @@
 	return copied;
 
 do_error:
-	tcp_remove_empty_skb(sk, tcp_write_queue_tail(sk));
+	tcp_remove_empty_skb(sk);
 	if (copied)
 		goto out;
 out_err:
@@ -1159,7 +1166,8 @@
 	struct sockaddr *uaddr = msg->msg_name;
 	int err, flags;
 
-	if (!(sock_net(sk)->ipv4.sysctl_tcp_fastopen & TFO_CLIENT_ENABLE) ||
+	if (!(READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fastopen) &
+	      TFO_CLIENT_ENABLE) ||
 	    (uaddr && msg->msg_namelen >= sizeof(uaddr->sa_family) &&
 	     uaddr->sa_family == AF_UNSPEC))
 		return -EOPNOTSUPP;
@@ -1311,7 +1319,7 @@
 			process_backlog++;
 			skb->ip_summed = CHECKSUM_PARTIAL;
 
-			skb_entail(sk, skb);
+			tcp_skb_entail(sk, skb);
 			copy = size_goal;
 
 			/* All packets are restored as if they have
@@ -1326,14 +1334,7 @@
 		if (copy > msg_data_left(msg))
 			copy = msg_data_left(msg);
 
-		/* Where to copy to? */
-		if (skb_availroom(skb) > 0 && !zc) {
-			/* We have some space in skb head. Superb! */
-			copy = min_t(int, copy, skb_availroom(skb));
-			err = skb_add_data_nocache(sk, skb, &msg->msg_iter, copy);
-			if (err)
-				goto do_fault;
-		} else if (!zc) {
+		if (!zc) {
 			bool merge = true;
 			int i = skb_shinfo(skb)->nr_frags;
 			struct page_frag *pfrag = sk_page_frag(sk);
@@ -1343,7 +1344,7 @@
 
 			if (!skb_can_coalesce(skb, i, pfrag->page,
 					      pfrag->offset)) {
-				if (i >= sysctl_max_skb_frags) {
+				if (i >= READ_ONCE(sysctl_max_skb_frags)) {
 					tcp_mark_push(tp, skb);
 					goto new_segment;
 				}
@@ -1432,9 +1433,7 @@
 	return copied + copied_syn;
 
 do_error:
-	skb = tcp_write_queue_tail(sk);
-do_fault:
-	tcp_remove_empty_skb(sk, skb);
+	tcp_remove_empty_skb(sk);
 
 	if (copied + copied_syn)
 		goto out;
@@ -1663,11 +1662,13 @@
 				if (!copied)
 					copied = used;
 				break;
-			} else if (used <= len) {
-				seq += used;
-				copied += used;
-				offset += used;
 			}
+			if (WARN_ON_ONCE(used > len))
+				used = len;
+			seq += used;
+			copied += used;
+			offset += used;
+
 			/* If recv_actor drops the lock (e.g. TCP splice
 			 * receive) the skb pointer might be invalid when
 			 * getting here: tcp_collapse might have deleted it
@@ -1719,7 +1720,7 @@
 	if (sk->sk_userlocks & SOCK_RCVBUF_LOCK)
 		cap = sk->sk_rcvbuf >> 1;
 	else
-		cap = sock_net(sk)->ipv4.sysctl_tcp_rmem[2] >> 1;
+		cap = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[2]) >> 1;
 	val = min(val, cap);
 	WRITE_ONCE(sk->sk_rcvlowat, val ? : 1);
 
@@ -1776,6 +1777,9 @@
 {
 	skb_frag_t *frag;
 
+	if (unlikely(offset_skb >= skb->len))
+		return NULL;
+
 	offset_skb -= skb_headlen(skb);
 	if ((int)offset_skb < 0 || skb_has_frag_list(skb))
 		return NULL;
@@ -1795,7 +1799,17 @@
 
 static bool can_map_frag(const skb_frag_t *frag)
 {
-	return skb_frag_size(frag) == PAGE_SIZE && !skb_frag_off(frag);
+	struct page *page;
+
+	if (skb_frag_size(frag) != PAGE_SIZE || skb_frag_off(frag))
+		return false;
+
+	page = skb_frag_page(frag);
+
+	if (PageCompound(page) || page->mapping)
+		return false;
+
+	return true;
 }
 
 static int find_next_mappable_frag(const skb_frag_t *frag,
@@ -2606,6 +2620,10 @@
 		if (oldstate != TCP_ESTABLISHED)
 			TCP_INC_STATS(sock_net(sk), TCP_MIB_CURRESTAB);
 		break;
+	case TCP_CLOSE_WAIT:
+		if (oldstate == TCP_SYN_RECV)
+			TCP_INC_STATS(sock_net(sk), TCP_MIB_CURRESTAB);
+		break;
 
 	case TCP_CLOSE:
 		if (oldstate == TCP_CLOSE_WAIT || oldstate == TCP_ESTABLISHED)
@@ -2617,7 +2635,7 @@
 			inet_put_port(sk);
 		fallthrough;
 	default:
-		if (oldstate == TCP_ESTABLISHED)
+		if (oldstate == TCP_ESTABLISHED || oldstate == TCP_CLOSE_WAIT)
 			TCP_DEC_STATS(sock_net(sk), TCP_MIB_CURRESTAB);
 	}
 
@@ -2679,7 +2697,7 @@
 	/* If we've already sent a FIN, or it's a closed state, skip this. */
 	if ((1 << sk->sk_state) &
 	    (TCPF_ESTABLISHED | TCPF_SYN_SENT |
-	     TCPF_SYN_RECV | TCPF_CLOSE_WAIT)) {
+	     TCPF_CLOSE_WAIT)) {
 		/* Clear out any half completed packets.  FIN if needed. */
 		if (tcp_close_state(sk))
 			tcp_send_fin(sk);
@@ -2687,11 +2705,37 @@
 }
 EXPORT_SYMBOL(tcp_shutdown);
 
+int tcp_orphan_count_sum(void)
+{
+	int i, total = 0;
+
+	for_each_possible_cpu(i)
+		total += per_cpu(tcp_orphan_count, i);
+
+	return max(total, 0);
+}
+
+static int tcp_orphan_cache;
+static struct timer_list tcp_orphan_timer;
+#define TCP_ORPHAN_TIMER_PERIOD msecs_to_jiffies(100)
+
+static void tcp_orphan_update(struct timer_list *unused)
+{
+	WRITE_ONCE(tcp_orphan_cache, tcp_orphan_count_sum());
+	mod_timer(&tcp_orphan_timer, jiffies + TCP_ORPHAN_TIMER_PERIOD);
+}
+
+static bool tcp_too_many_orphans(int shift)
+{
+	return READ_ONCE(tcp_orphan_cache) << shift >
+		READ_ONCE(sysctl_tcp_max_orphans);
+}
+
 bool tcp_check_oom(struct sock *sk, int shift)
 {
 	bool too_many_orphans, out_of_socket_memory;
 
-	too_many_orphans = tcp_too_many_orphans(sk, shift);
+	too_many_orphans = tcp_too_many_orphans(shift);
 	out_of_socket_memory = tcp_out_of_memory(sk);
 
 	if (too_many_orphans)
@@ -2707,7 +2751,7 @@
 	int data_was_unread = 0;
 	int state;
 
-	sk->sk_shutdown = SHUTDOWN_MASK;
+	WRITE_ONCE(sk->sk_shutdown, SHUTDOWN_MASK);
 
 	if (sk->sk_state == TCP_LISTEN) {
 		tcp_set_state(sk, TCP_CLOSE);
@@ -2764,7 +2808,7 @@
 		 * machine. State transitions:
 		 *
 		 * TCP_ESTABLISHED -> TCP_FIN_WAIT1
-		 * TCP_SYN_RECV	-> TCP_FIN_WAIT1 (forget it, it's impossible)
+		 * TCP_SYN_RECV	-> TCP_FIN_WAIT1 (it is difficult)
 		 * TCP_CLOSE_WAIT -> TCP_LAST_ACK
 		 *
 		 * are legal only when FIN has been sent (i.e. in window),
@@ -2800,7 +2844,7 @@
 	/* remove backlog if any, without releasing ownership. */
 	__release_sock(sk);
 
-	percpu_counter_inc(sk->sk_prot->orphan_count);
+	this_cpu_inc(tcp_orphan_count);
 
 	/* Have we already been destroyed by a softirq or backlog? */
 	if (state != TCP_CLOSE && sk->sk_state == TCP_CLOSE)
@@ -2877,6 +2921,8 @@
 	lock_sock(sk);
 	__tcp_close(sk, timeout);
 	release_sock(sk);
+	if (!sk->sk_net_refcnt)
+		inet_csk_clear_xmit_timers_sync(sk);
 	sock_put(sk);
 }
 EXPORT_SYMBOL(tcp_close);
@@ -2937,6 +2983,12 @@
 	int old_state = sk->sk_state;
 	u32 seq;
 
+	/* Deny disconnect if other threads are blocked in sk_wait_event()
+	 * or inet_wait_for_connect().
+	 */
+	if (sk->sk_wait_pending)
+		return -EBUSY;
+
 	if (old_state != TCP_CLOSE)
 		tcp_set_state(sk, TCP_CLOSE);
 
@@ -2944,7 +2996,7 @@
 	if (old_state == TCP_LISTEN) {
 		inet_csk_listen_stop(sk);
 	} else if (unlikely(tp->repair)) {
-		sk->sk_err = ECONNABORTED;
+		WRITE_ONCE(sk->sk_err, ECONNABORTED);
 	} else if (tcp_need_reset(old_state) ||
 		   (tp->snd_nxt != tp->write_seq &&
 		    (1 << old_state) & (TCPF_CLOSING | TCPF_LAST_ACK))) {
@@ -2952,9 +3004,9 @@
 		 * states
 		 */
 		tcp_send_active_reset(sk, gfp_any());
-		sk->sk_err = ECONNRESET;
+		WRITE_ONCE(sk->sk_err, ECONNRESET);
 	} else if (old_state == TCP_SYN_SENT)
-		sk->sk_err = ECONNRESET;
+		WRITE_ONCE(sk->sk_err, ECONNRESET);
 
 	tcp_clear_xmit_timers(sk);
 	__skb_queue_purge(&sk->sk_receive_queue);
@@ -2973,7 +3025,7 @@
 	if (!(sk->sk_userlocks & SOCK_BINDADDR_LOCK))
 		inet_reset_saddr(sk);
 
-	sk->sk_shutdown = 0;
+	WRITE_ONCE(sk->sk_shutdown, 0);
 	sock_reset_flag(sk, SOCK_DONE);
 	tp->srtt_us = 0;
 	tp->mdev_us = jiffies_to_usecs(TCP_TIMEOUT_INIT);
@@ -2991,8 +3043,10 @@
 	icsk->icsk_rto_min = TCP_RTO_MIN;
 	icsk->icsk_delack_max = TCP_DELACK_MAX;
 	tp->snd_ssthresh = TCP_INFINITE_SSTHRESH;
-	tp->snd_cwnd = TCP_INIT_CWND;
+	tcp_snd_cwnd_set(tp, TCP_INIT_CWND);
 	tp->snd_cwnd_cnt = 0;
+	tp->is_cwnd_limited = 0;
+	tp->max_packets_out = 0;
 	tp->window_clamp = 0;
 	tp->delivered = 0;
 	tp->delivered_ce = 0;
@@ -3011,8 +3065,7 @@
 	icsk->icsk_ack.rcv_mss = TCP_MIN_MSS;
 	memset(&tp->rx_opt, 0, sizeof(tp->rx_opt));
 	__sk_dst_reset(sk);
-	dst_release(sk->sk_rx_dst);
-	sk->sk_rx_dst = NULL;
+	dst_release(xchg((__force struct dst_entry **)&sk->sk_rx_dst, NULL));
 	tcp_saved_syn_free(tp);
 	tp->compressed_ack = 0;
 	tp->segs_in = 0;
@@ -3033,6 +3086,7 @@
 	tp->last_oow_ack_time = 0;
 	/* There's a bubble in the pipe until at least the first ACK. */
 	tp->app_limited = ~0U;
+	tp->rate_app_limited = 1;
 	tp->rack.mstamp = 0;
 	tp->rack.advanced = 0;
 	tp->rack.reo_wnd_steps = 1;
@@ -3253,7 +3307,7 @@
 		return -EINVAL;
 
 	lock_sock(sk);
-	inet_csk(sk)->icsk_syn_retries = val;
+	WRITE_ONCE(inet_csk(sk)->icsk_syn_retries, val);
 	release_sock(sk);
 	return 0;
 }
@@ -3262,7 +3316,7 @@
 void tcp_sock_set_user_timeout(struct sock *sk, u32 val)
 {
 	lock_sock(sk);
-	inet_csk(sk)->icsk_user_timeout = val;
+	WRITE_ONCE(inet_csk(sk)->icsk_user_timeout, val);
 	release_sock(sk);
 }
 EXPORT_SYMBOL(tcp_sock_set_user_timeout);
@@ -3274,7 +3328,8 @@
 	if (val < 1 || val > MAX_TCP_KEEPIDLE)
 		return -EINVAL;
 
-	tp->keepalive_time = val * HZ;
+	/* Paired with WRITE_ONCE() in keepalive_time_when() */
+	WRITE_ONCE(tp->keepalive_time, val * HZ);
 	if (sock_flag(sk, SOCK_KEEPOPEN) &&
 	    !((1 << sk->sk_state) & (TCPF_CLOSE | TCPF_LISTEN))) {
 		u32 elapsed = keepalive_time_elapsed(tp);
@@ -3306,7 +3361,7 @@
 		return -EINVAL;
 
 	lock_sock(sk);
-	tcp_sk(sk)->keepalive_intvl = val * HZ;
+	WRITE_ONCE(tcp_sk(sk)->keepalive_intvl, val * HZ);
 	release_sock(sk);
 	return 0;
 }
@@ -3318,7 +3373,8 @@
 		return -EINVAL;
 
 	lock_sock(sk);
-	tcp_sk(sk)->keepalive_probes = val;
+	/* Paired with READ_ONCE() in keepalive_probes() */
+	WRITE_ONCE(tcp_sk(sk)->keepalive_probes, val);
 	release_sock(sk);
 	return 0;
 }
@@ -3503,7 +3559,7 @@
 	case TCP_REPAIR_OPTIONS:
 		if (!tp->repair)
 			err = -EINVAL;
-		else if (sk->sk_state == TCP_ESTABLISHED)
+		else if (sk->sk_state == TCP_ESTABLISHED && !tp->bytes_sent)
 			err = tcp_repair_options_est(sk, optval, optlen);
 		else
 			err = -EPERM;
@@ -3520,19 +3576,19 @@
 		if (val < 1 || val > MAX_TCP_KEEPINTVL)
 			err = -EINVAL;
 		else
-			tp->keepalive_intvl = val * HZ;
+			WRITE_ONCE(tp->keepalive_intvl, val * HZ);
 		break;
 	case TCP_KEEPCNT:
 		if (val < 1 || val > MAX_TCP_KEEPCNT)
 			err = -EINVAL;
 		else
-			tp->keepalive_probes = val;
+			WRITE_ONCE(tp->keepalive_probes, val);
 		break;
 	case TCP_SYNCNT:
 		if (val < 1 || val > MAX_TCP_SYNCNT)
 			err = -EINVAL;
 		else
-			icsk->icsk_syn_retries = val;
+			WRITE_ONCE(icsk->icsk_syn_retries, val);
 		break;
 
 	case TCP_SAVE_SYN:
@@ -3545,18 +3601,18 @@
 
 	case TCP_LINGER2:
 		if (val < 0)
-			tp->linger2 = -1;
+			WRITE_ONCE(tp->linger2, -1);
 		else if (val > TCP_FIN_TIMEOUT_MAX / HZ)
-			tp->linger2 = TCP_FIN_TIMEOUT_MAX;
+			WRITE_ONCE(tp->linger2, TCP_FIN_TIMEOUT_MAX);
 		else
-			tp->linger2 = val * HZ;
+			WRITE_ONCE(tp->linger2, val * HZ);
 		break;
 
 	case TCP_DEFER_ACCEPT:
 		/* Translate value in seconds to number of retransmits */
-		icsk->icsk_accept_queue.rskq_defer_accept =
-			secs_to_retrans(val, TCP_TIMEOUT_INIT / HZ,
-					TCP_RTO_MAX / HZ);
+		WRITE_ONCE(icsk->icsk_accept_queue.rskq_defer_accept,
+			   secs_to_retrans(val, TCP_TIMEOUT_INIT / HZ,
+					   TCP_RTO_MAX / HZ));
 		break;
 
 	case TCP_WINDOW_CLAMP:
@@ -3580,7 +3636,7 @@
 		if (val < 0)
 			err = -EINVAL;
 		else
-			icsk->icsk_user_timeout = val;
+			WRITE_ONCE(icsk->icsk_user_timeout, val);
 		break;
 
 	case TCP_FASTOPEN:
@@ -3596,7 +3652,8 @@
 	case TCP_FASTOPEN_CONNECT:
 		if (val > 1 || val < 0) {
 			err = -EINVAL;
-		} else if (net->ipv4.sysctl_tcp_fastopen & TFO_CLIENT_ENABLE) {
+		} else if (READ_ONCE(net->ipv4.sysctl_tcp_fastopen) &
+			   TFO_CLIENT_ENABLE) {
 			if (sk->sk_state == TCP_CLOSE)
 				tp->fastopen_connect = val;
 			else
@@ -3623,7 +3680,7 @@
 		err = tcp_repair_set_window(tp, optval, optlen);
 		break;
 	case TCP_NOTSENT_LOWAT:
-		tp->notsent_lowat = val;
+		WRITE_ONCE(tp->notsent_lowat, val);
 		sk->sk_write_space(sk);
 		break;
 	case TCP_INQ:
@@ -3635,7 +3692,7 @@
 	case TCP_TX_DELAY:
 		if (val)
 			tcp_enable_tx_delay();
-		tp->tcp_tx_delay = val;
+		WRITE_ONCE(tp->tcp_tx_delay, val);
 		break;
 	default:
 		err = -ENOPROTOOPT;
@@ -3652,8 +3709,9 @@
 	const struct inet_connection_sock *icsk = inet_csk(sk);
 
 	if (level != SOL_TCP)
-		return icsk->icsk_af_ops->setsockopt(sk, level, optname,
-						     optval, optlen);
+		/* Paired with WRITE_ONCE() in do_ipv6_setsockopt() and tcp_v6_connect() */
+		return READ_ONCE(icsk->icsk_af_ops)->setsockopt(sk, level, optname,
+								optval, optlen);
 	return do_tcp_setsockopt(sk, level, optname, optval, optlen);
 }
 EXPORT_SYMBOL(tcp_setsockopt);
@@ -3703,7 +3761,7 @@
 	info->tcpi_max_pacing_rate = rate64;
 
 	info->tcpi_reordering = tp->reordering;
-	info->tcpi_snd_cwnd = tp->snd_cwnd;
+	info->tcpi_snd_cwnd = tcp_snd_cwnd(tp);
 
 	if (info->tcpi_state == TCP_LISTEN) {
 		/* listeners aliased fields :
@@ -3872,7 +3930,7 @@
 	rate64 = tcp_compute_delivery_rate(tp);
 	nla_put_u64_64bit(stats, TCP_NLA_DELIVERY_RATE, rate64, TCP_NLA_PAD);
 
-	nla_put_u32(stats, TCP_NLA_SND_CWND, tp->snd_cwnd);
+	nla_put_u32(stats, TCP_NLA_SND_CWND, tcp_snd_cwnd(tp));
 	nla_put_u32(stats, TCP_NLA_REORDERING, tp->reordering);
 	nla_put_u32(stats, TCP_NLA_MIN_RTT, tcp_min_rtt(tp));
 
@@ -3915,15 +3973,16 @@
 	if (get_user(len, optlen))
 		return -EFAULT;
 
-	len = min_t(unsigned int, len, sizeof(int));
-
 	if (len < 0)
 		return -EINVAL;
 
+	len = min_t(unsigned int, len, sizeof(int));
+
 	switch (optname) {
 	case TCP_MAXSEG:
 		val = tp->mss_cache;
-		if (!val && ((1 << sk->sk_state) & (TCPF_CLOSE | TCPF_LISTEN)))
+		if (tp->rx_opt.user_mss &&
+		    ((1 << sk->sk_state) & (TCPF_CLOSE | TCPF_LISTEN)))
 			val = tp->rx_opt.user_mss;
 		if (tp->repair)
 			val = tp->rx_opt.mss_clamp;
@@ -3944,16 +4003,18 @@
 		val = keepalive_probes(tp);
 		break;
 	case TCP_SYNCNT:
-		val = icsk->icsk_syn_retries ? : net->ipv4.sysctl_tcp_syn_retries;
+		val = READ_ONCE(icsk->icsk_syn_retries) ? :
+			READ_ONCE(net->ipv4.sysctl_tcp_syn_retries);
 		break;
 	case TCP_LINGER2:
-		val = tp->linger2;
+		val = READ_ONCE(tp->linger2);
 		if (val >= 0)
-			val = (val ? : net->ipv4.sysctl_tcp_fin_timeout) / HZ;
+			val = (val ? : READ_ONCE(net->ipv4.sysctl_tcp_fin_timeout)) / HZ;
 		break;
 	case TCP_DEFER_ACCEPT:
-		val = retrans_to_secs(icsk->icsk_accept_queue.rskq_defer_accept,
-				      TCP_TIMEOUT_INIT / HZ, TCP_RTO_MAX / HZ);
+		val = READ_ONCE(icsk->icsk_accept_queue.rskq_defer_accept);
+		val = retrans_to_secs(val, TCP_TIMEOUT_INIT / HZ,
+				      TCP_RTO_MAX / HZ);
 		break;
 	case TCP_WINDOW_CLAMP:
 		val = tp->window_clamp;
@@ -4089,11 +4150,11 @@
 		break;
 
 	case TCP_USER_TIMEOUT:
-		val = icsk->icsk_user_timeout;
+		val = READ_ONCE(icsk->icsk_user_timeout);
 		break;
 
 	case TCP_FASTOPEN:
-		val = icsk->icsk_accept_queue.fastopenq.max_qlen;
+		val = READ_ONCE(icsk->icsk_accept_queue.fastopenq.max_qlen);
 		break;
 
 	case TCP_FASTOPEN_CONNECT:
@@ -4105,14 +4166,14 @@
 		break;
 
 	case TCP_TX_DELAY:
-		val = tp->tcp_tx_delay;
+		val = READ_ONCE(tp->tcp_tx_delay);
 		break;
 
 	case TCP_TIMESTAMP:
 		val = tcp_time_stamp_raw() + tp->tsoffset;
 		break;
 	case TCP_NOTSENT_LOWAT:
-		val = tp->notsent_lowat;
+		val = READ_ONCE(tp->notsent_lowat);
 		break;
 	case TCP_INQ:
 		val = tp->recvmsg_inq;
@@ -4248,8 +4309,9 @@
 	struct inet_connection_sock *icsk = inet_csk(sk);
 
 	if (level != SOL_TCP)
-		return icsk->icsk_af_ops->getsockopt(sk, level, optname,
-						     optval, optlen);
+		/* Paired with WRITE_ONCE() in do_ipv6_setsockopt() and tcp_v6_connect() */
+		return READ_ONCE(icsk->icsk_af_ops)->getsockopt(sk, level, optname,
+								optval, optlen);
 	return do_tcp_getsockopt(sk, level, optname, optval, optlen);
 }
 EXPORT_SYMBOL(tcp_getsockopt);
@@ -4296,12 +4358,16 @@
 	 * to memory. See smp_rmb() in tcp_get_md5sig_pool()
 	 */
 	smp_wmb();
-	tcp_md5sig_pool_populated = true;
+	/* Paired with READ_ONCE() from tcp_alloc_md5sig_pool()
+	 * and tcp_get_md5sig_pool().
+	*/
+	WRITE_ONCE(tcp_md5sig_pool_populated, true);
 }
 
 bool tcp_alloc_md5sig_pool(void)
 {
-	if (unlikely(!tcp_md5sig_pool_populated)) {
+	/* Paired with WRITE_ONCE() from __tcp_alloc_md5sig_pool() */
+	if (unlikely(!READ_ONCE(tcp_md5sig_pool_populated))) {
 		mutex_lock(&tcp_md5sig_mutex);
 
 		if (!tcp_md5sig_pool_populated) {
@@ -4312,7 +4378,8 @@
 
 		mutex_unlock(&tcp_md5sig_mutex);
 	}
-	return tcp_md5sig_pool_populated;
+	/* Paired with WRITE_ONCE() from __tcp_alloc_md5sig_pool() */
+	return READ_ONCE(tcp_md5sig_pool_populated);
 }
 EXPORT_SYMBOL(tcp_alloc_md5sig_pool);
 
@@ -4328,7 +4395,8 @@
 {
 	local_bh_disable();
 
-	if (tcp_md5sig_pool_populated) {
+	/* Paired with WRITE_ONCE() from __tcp_alloc_md5sig_pool() */
+	if (READ_ONCE(tcp_md5sig_pool_populated)) {
 		/* coupled with smp_wmb() in __tcp_alloc_md5sig_pool() */
 		smp_rmb();
 		return this_cpu_ptr(&tcp_md5sig_pool);
@@ -4410,7 +4478,7 @@
 	if (req)
 		reqsk_fastopen_remove(sk, req, false);
 
-	sk->sk_shutdown = SHUTDOWN_MASK;
+	WRITE_ONCE(sk->sk_shutdown, SHUTDOWN_MASK);
 
 	if (!sock_flag(sk, SOCK_DEAD))
 		sk->sk_state_change(sk);
@@ -4446,13 +4514,9 @@
 	bh_lock_sock(sk);
 
 	if (!sock_flag(sk, SOCK_DEAD)) {
-		sk->sk_err = err;
-		/* This barrier is coupled with smp_rmb() in tcp_poll() */
-		smp_wmb();
-		sk_error_report(sk);
 		if (tcp_need_reset(sk->sk_state))
 			tcp_send_active_reset(sk, GFP_ATOMIC);
-		tcp_done(sk);
+		tcp_done_with_error(sk, err);
 	}
 
 	bh_unlock_sock(sk);
@@ -4502,8 +4566,10 @@
 		     sizeof_field(struct sk_buff, cb));
 
 	percpu_counter_init(&tcp_sockets_allocated, 0, GFP_KERNEL);
-	percpu_counter_init(&tcp_orphan_count, 0, GFP_KERNEL);
-	inet_hashinfo_init(&tcp_hashinfo);
+
+	timer_setup(&tcp_orphan_timer, tcp_orphan_update, TIMER_DEFERRABLE);
+	mod_timer(&tcp_orphan_timer, jiffies + TCP_ORPHAN_TIMER_PERIOD);
+
 	inet_hashinfo2_init(&tcp_hashinfo, "tcp_listen_portaddr_hash",
 			    thash_entries, 21,  /* one slot per 2 MB*/
 			    0, 64 * 1024);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_bbr.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_bbr.c
@@ -274,7 +274,7 @@
 	} else {			 /* no RTT sample yet */
 		rtt_us = USEC_PER_MSEC;	 /* use nominal default RTT */
 	}
-	bw = (u64)tp->snd_cwnd * BW_UNIT;
+	bw = (u64)tcp_snd_cwnd(tp) * BW_UNIT;
 	do_div(bw, rtt_us);
 	sk->sk_pacing_rate = bbr_bw_to_pacing_rate(sk, bw, bbr_high_gain);
 }
@@ -321,9 +321,9 @@
 	struct bbr *bbr = inet_csk_ca(sk);
 
 	if (bbr->prev_ca_state < TCP_CA_Recovery && bbr->mode != BBR_PROBE_RTT)
-		bbr->prior_cwnd = tp->snd_cwnd;  /* this cwnd is good enough */
+		bbr->prior_cwnd = tcp_snd_cwnd(tp);  /* this cwnd is good enough */
 	else  /* loss recovery or BBR_PROBE_RTT have temporarily cut cwnd */
-		bbr->prior_cwnd = max(bbr->prior_cwnd, tp->snd_cwnd);
+		bbr->prior_cwnd = max(bbr->prior_cwnd, tcp_snd_cwnd(tp));
 }
 
 static void bbr_cwnd_event(struct sock *sk, enum tcp_ca_event event)
@@ -480,7 +480,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct bbr *bbr = inet_csk_ca(sk);
 	u8 prev_state = bbr->prev_ca_state, state = inet_csk(sk)->icsk_ca_state;
-	u32 cwnd = tp->snd_cwnd;
+	u32 cwnd = tcp_snd_cwnd(tp);
 
 	/* An ACK for P pkts should release at most 2*P packets. We do this
 	 * in two steps. First, here we deduct the number of lost packets.
@@ -518,7 +518,7 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct bbr *bbr = inet_csk_ca(sk);
-	u32 cwnd = tp->snd_cwnd, target_cwnd = 0;
+	u32 cwnd = tcp_snd_cwnd(tp), target_cwnd = 0;
 
 	if (!acked)
 		goto done;  /* no packet fully ACKed; just apply caps */
@@ -542,9 +542,9 @@
 	cwnd = max(cwnd, bbr_cwnd_min_target);
 
 done:
-	tp->snd_cwnd = min(cwnd, tp->snd_cwnd_clamp);	/* apply global cap */
+	tcp_snd_cwnd_set(tp, min(cwnd, tp->snd_cwnd_clamp));	/* apply global cap */
 	if (bbr->mode == BBR_PROBE_RTT)  /* drain queue, refresh min_rtt */
-		tp->snd_cwnd = min(tp->snd_cwnd, bbr_cwnd_min_target);
+		tcp_snd_cwnd_set(tp, min(tcp_snd_cwnd(tp), bbr_cwnd_min_target));
 }
 
 /* End cycle phase if it's time and/or we hit the phase's in-flight target. */
@@ -854,7 +854,7 @@
 	bbr->ack_epoch_acked = min_t(u32, 0xFFFFF,
 				     bbr->ack_epoch_acked + rs->acked_sacked);
 	extra_acked = bbr->ack_epoch_acked - expected_acked;
-	extra_acked = min(extra_acked, tp->snd_cwnd);
+	extra_acked = min(extra_acked, tcp_snd_cwnd(tp));
 	if (extra_acked > bbr->extra_acked[bbr->extra_acked_win_idx])
 		bbr->extra_acked[bbr->extra_acked_win_idx] = extra_acked;
 }
@@ -912,7 +912,7 @@
 		return;
 
 	bbr->min_rtt_stamp = tcp_jiffies32;  /* wait a while until PROBE_RTT */
-	tp->snd_cwnd = max(tp->snd_cwnd, bbr->prior_cwnd);
+	tcp_snd_cwnd_set(tp, max(tcp_snd_cwnd(tp), bbr->prior_cwnd));
 	bbr_reset_mode(sk);
 }
 
@@ -1091,7 +1091,7 @@
 	bbr->full_bw = 0;   /* spurious slow-down; reset full pipe detection */
 	bbr->full_bw_cnt = 0;
 	bbr_reset_lt_bw_sampling(sk);
-	return tcp_sk(sk)->snd_cwnd;
+	return tcp_snd_cwnd(tcp_sk(sk));
 }
 
 /* Entering loss recovery, so save cwnd for when we exit or undo recovery. */
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_bic.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_bic.c
@@ -150,7 +150,7 @@
 		if (!acked)
 			return;
 	}
-	bictcp_update(ca, tp->snd_cwnd);
+	bictcp_update(ca, tcp_snd_cwnd(tp));
 	tcp_cong_avoid_ai(tp, ca->cnt, acked);
 }
 
@@ -166,16 +166,16 @@
 	ca->epoch_start = 0;	/* end of epoch */
 
 	/* Wmax and fast convergence */
-	if (tp->snd_cwnd < ca->last_max_cwnd && fast_convergence)
-		ca->last_max_cwnd = (tp->snd_cwnd * (BICTCP_BETA_SCALE + beta))
+	if (tcp_snd_cwnd(tp) < ca->last_max_cwnd && fast_convergence)
+		ca->last_max_cwnd = (tcp_snd_cwnd(tp) * (BICTCP_BETA_SCALE + beta))
 			/ (2 * BICTCP_BETA_SCALE);
 	else
-		ca->last_max_cwnd = tp->snd_cwnd;
+		ca->last_max_cwnd = tcp_snd_cwnd(tp);
 
-	if (tp->snd_cwnd <= low_window)
-		return max(tp->snd_cwnd >> 1U, 2U);
+	if (tcp_snd_cwnd(tp) <= low_window)
+		return max(tcp_snd_cwnd(tp) >> 1U, 2U);
 	else
-		return max((tp->snd_cwnd * beta) / BICTCP_BETA_SCALE, 2U);
+		return max((tcp_snd_cwnd(tp) * beta) / BICTCP_BETA_SCALE, 2U);
 }
 
 static void bictcp_state(struct sock *sk, u8 new_state)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_bpf.c
@@ -6,6 +6,7 @@
 #include <linux/bpf.h>
 #include <linux/init.h>
 #include <linux/wait.h>
+#include <linux/util_macros.h>
 
 #include <net/inet_common.h>
 #include <net/tls.h>
@@ -30,13 +31,14 @@
 		sge = sk_msg_elem(msg, i);
 		size = (apply && apply_bytes < sge->length) ?
 			apply_bytes : sge->length;
-		if (!sk_wmem_schedule(sk, size)) {
+		if (!__sk_rmem_schedule(sk, size, false)) {
 			if (!copied)
 				ret = -ENOMEM;
 			break;
 		}
 
 		sk_mem_charge(sk, size);
+		atomic_add(size, &sk->sk_rmem_alloc);
 		sk_msg_xfer(tmp, msg, i, size);
 		copied += size;
 		if (sge->length)
@@ -45,14 +47,18 @@
 		tmp->sg.end = i;
 		if (apply) {
 			apply_bytes -= size;
-			if (!apply_bytes)
+			if (!apply_bytes) {
+				if (sge->length)
+					sk_msg_iter_var_prev(i);
 				break;
+			}
 		}
 	} while (i != msg->sg.end);
 
 	if (!ret) {
 		msg->sg.start = i;
-		sk_psock_queue_msg(psock, tmp);
+		if (!sk_psock_queue_msg(psock, tmp))
+			atomic_sub(copied, &sk->sk_rmem_alloc);
 		sk_psock_data_ready(sk, psock);
 	} else {
 		sk_msg_free(sk, tmp);
@@ -131,17 +137,15 @@
 	return ret;
 }
 
-int tcp_bpf_sendmsg_redir(struct sock *sk, struct sk_msg *msg,
-			  u32 bytes, int flags)
+int tcp_bpf_sendmsg_redir(struct sock *sk, bool ingress,
+			  struct sk_msg *msg, u32 bytes, int flags)
 {
-	bool ingress = sk_msg_to_ingress(msg);
 	struct sk_psock *psock = sk_psock_get(sk);
 	int ret;
 
-	if (unlikely(!psock)) {
-		sk_msg_free(sk, msg);
-		return 0;
-	}
+	if (unlikely(!psock))
+		return -EPIPE;
+
 	ret = ingress ? bpf_tcp_ingress(sk, psock, msg, bytes, flags) :
 			tcp_bpf_push_locked(sk, msg, bytes, flags, false);
 	sk_psock_put(sk, psock);
@@ -166,12 +170,128 @@
 	sk_set_bit(SOCKWQ_ASYNC_WAITDATA, sk);
 	ret = sk_wait_event(sk, &timeo,
 			    !list_empty(&psock->ingress_msg) ||
-			    !skb_queue_empty(&sk->sk_receive_queue), &wait);
+			    !skb_queue_empty_lockless(&sk->sk_receive_queue), &wait);
 	sk_clear_bit(SOCKWQ_ASYNC_WAITDATA, sk);
 	remove_wait_queue(sk_sleep(sk), &wait);
 	return ret;
 }
 
+static bool is_next_msg_fin(struct sk_psock *psock)
+{
+	struct scatterlist *sge;
+	struct sk_msg *msg_rx;
+	int i;
+
+	msg_rx = sk_psock_peek_msg(psock);
+	i = msg_rx->sg.start;
+	sge = sk_msg_elem(msg_rx, i);
+	if (!sge->length) {
+		struct sk_buff *skb = msg_rx->skb;
+
+		if (skb && TCP_SKB_CB(skb)->tcp_flags & TCPHDR_FIN)
+			return true;
+	}
+	return false;
+}
+
+static int tcp_bpf_recvmsg_parser(struct sock *sk,
+				  struct msghdr *msg,
+				  size_t len,
+				  int nonblock,
+				  int flags,
+				  int *addr_len)
+{
+	struct sk_psock *psock;
+	int copied;
+
+	if (unlikely(flags & MSG_ERRQUEUE))
+		return inet_recv_error(sk, msg, len, addr_len);
+
+	if (!len)
+		return 0;
+
+	psock = sk_psock_get(sk);
+	if (unlikely(!psock))
+		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
+
+	lock_sock(sk);
+
+	/* We may have received data on the sk_receive_queue pre-accept and
+	 * then we can not use read_skb in this context because we haven't
+	 * assigned a sk_socket yet so have no link to the ops. The work-around
+	 * is to check the sk_receive_queue and in these cases read skbs off
+	 * queue again. The read_skb hook is not running at this point because
+	 * of lock_sock so we avoid having multiple runners in read_skb.
+	 */
+	if (unlikely(!skb_queue_empty(&sk->sk_receive_queue))) {
+		tcp_data_ready(sk);
+		/* This handles the ENOMEM errors if we both receive data
+		 * pre accept and are already under memory pressure. At least
+		 * let user know to retry.
+		 */
+		if (unlikely(!skb_queue_empty(&sk->sk_receive_queue))) {
+			copied = -EAGAIN;
+			goto out;
+		}
+	}
+
+msg_bytes_ready:
+	copied = sk_msg_recvmsg(sk, psock, msg, len, flags);
+	/* The typical case for EFAULT is the socket was gracefully
+	 * shutdown with a FIN pkt. So check here the other case is
+	 * some error on copy_page_to_iter which would be unexpected.
+	 * On fin return correct return code to zero.
+	 */
+	if (copied == -EFAULT) {
+		bool is_fin = is_next_msg_fin(psock);
+
+		if (is_fin) {
+			copied = 0;
+			goto out;
+		}
+	}
+	if (!copied) {
+		long timeo;
+		int data;
+
+		if (sock_flag(sk, SOCK_DONE))
+			goto out;
+
+		if (sk->sk_err) {
+			copied = sock_error(sk);
+			goto out;
+		}
+
+		if (sk->sk_shutdown & RCV_SHUTDOWN)
+			goto out;
+
+		if (sk->sk_state == TCP_CLOSE) {
+			copied = -ENOTCONN;
+			goto out;
+		}
+
+		timeo = sock_rcvtimeo(sk, nonblock);
+		if (!timeo) {
+			copied = -EAGAIN;
+			goto out;
+		}
+
+		if (signal_pending(current)) {
+			copied = sock_intr_errno(timeo);
+			goto out;
+		}
+
+		data = tcp_msg_wait_data(sk, psock, timeo);
+		if (data && !sk_psock_queue_empty(psock))
+			goto msg_bytes_ready;
+		copied = -EAGAIN;
+	}
+out:
+	release_sock(sk);
+	sk_psock_put(sk, psock);
+	return copied;
+}
+
 static int tcp_bpf_recvmsg(struct sock *sk, struct msghdr *msg, size_t len,
 		    int nonblock, int flags, int *addr_len)
 {
@@ -181,6 +301,9 @@
 	if (unlikely(flags & MSG_ERRQUEUE))
 		return inet_recv_error(sk, msg, len, addr_len);
 
+	if (!len)
+		return 0;
+
 	psock = sk_psock_get(sk);
 	if (unlikely(!psock))
 		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
@@ -216,10 +339,10 @@
 static int tcp_bpf_send_verdict(struct sock *sk, struct sk_psock *psock,
 				struct sk_msg *msg, int *copied, int flags)
 {
-	bool cork = false, enospc = sk_msg_full(msg);
+	bool cork = false, enospc = sk_msg_full(msg), redir_ingress;
 	struct sock *sk_redir;
-	u32 tosend, delta = 0;
-	u32 eval = __SK_NONE;
+	u32 tosend, origsize, sent, delta = 0;
+	u32 eval;
 	int ret;
 
 more_data:
@@ -250,6 +373,7 @@
 	tosend = msg->sg.size;
 	if (psock->apply_bytes && psock->apply_bytes < tosend)
 		tosend = psock->apply_bytes;
+	eval = __SK_NONE;
 
 	switch (psock->eval) {
 	case __SK_PASS:
@@ -261,6 +385,7 @@
 		sk_msg_apply_bytes(psock, tosend);
 		break;
 	case __SK_REDIRECT:
+		redir_ingress = psock->redir_ingress;
 		sk_redir = psock->sk_redir;
 		sk_msg_apply_bytes(psock, tosend);
 		if (!psock->apply_bytes) {
@@ -273,17 +398,20 @@
 			cork = true;
 			psock->cork = NULL;
 		}
-		sk_msg_return(sk, msg, tosend);
 		release_sock(sk);
 
-		ret = tcp_bpf_sendmsg_redir(sk_redir, msg, tosend, flags);
+		origsize = msg->sg.size;
+		ret = tcp_bpf_sendmsg_redir(sk_redir, redir_ingress,
+					    msg, tosend, flags);
+		sent = origsize - msg->sg.size;
 
 		if (eval == __SK_REDIRECT)
 			sock_put(sk_redir);
 
 		lock_sock(sk);
+		sk_mem_uncharge(sk, sent);
 		if (unlikely(ret < 0)) {
-			int free = sk_msg_free_nocharge(sk, msg);
+			int free = sk_msg_free(sk, msg);
 
 			if (!cork)
 				*copied -= free;
@@ -297,7 +425,7 @@
 		break;
 	case __SK_DROP:
 	default:
-		sk_msg_free_partial(sk, msg, tosend);
+		sk_msg_free(sk, msg);
 		sk_msg_apply_bytes(psock, tosend);
 		*copied -= (tosend + delta);
 		return -EACCES;
@@ -404,7 +532,7 @@
 		err = sk_stream_error(sk, msg->msg_flags, err);
 	release_sock(sk);
 	sk_psock_put(sk, psock);
-	return copied ? copied : err;
+	return copied > 0 ? copied : err;
 }
 
 static int tcp_bpf_sendpage(struct sock *sk, struct page *page, int offset,
@@ -464,6 +592,8 @@
 enum {
 	TCP_BPF_BASE,
 	TCP_BPF_TX,
+	TCP_BPF_RX,
+	TCP_BPF_TXRX,
 	TCP_BPF_NUM_CFGS,
 };
 
@@ -475,7 +605,7 @@
 				   struct proto *base)
 {
 	prot[TCP_BPF_BASE]			= *base;
-	prot[TCP_BPF_BASE].unhash		= sock_map_unhash;
+	prot[TCP_BPF_BASE].destroy		= sock_map_destroy;
 	prot[TCP_BPF_BASE].close		= sock_map_close;
 	prot[TCP_BPF_BASE].recvmsg		= tcp_bpf_recvmsg;
 	prot[TCP_BPF_BASE].sock_is_readable	= sk_msg_is_readable;
@@ -483,6 +613,12 @@
 	prot[TCP_BPF_TX]			= prot[TCP_BPF_BASE];
 	prot[TCP_BPF_TX].sendmsg		= tcp_bpf_sendmsg;
 	prot[TCP_BPF_TX].sendpage		= tcp_bpf_sendpage;
+
+	prot[TCP_BPF_RX]			= prot[TCP_BPF_BASE];
+	prot[TCP_BPF_RX].recvmsg		= tcp_bpf_recvmsg_parser;
+
+	prot[TCP_BPF_TXRX]			= prot[TCP_BPF_TX];
+	prot[TCP_BPF_TXRX].recvmsg		= tcp_bpf_recvmsg_parser;
 }
 
 static void tcp_bpf_check_v6_needs_rebuild(struct proto *ops)
@@ -520,6 +656,10 @@
 	int family = sk->sk_family == AF_INET6 ? TCP_BPF_IPV6 : TCP_BPF_IPV4;
 	int config = psock->progs.msg_parser   ? TCP_BPF_TX   : TCP_BPF_BASE;
 
+	if (psock->progs.stream_verdict || psock->progs.skb_verdict) {
+		config = (config == TCP_BPF_TX) ? TCP_BPF_TXRX : TCP_BPF_RX;
+	}
+
 	if (restore) {
 		if (inet_csk_has_ulp(sk)) {
 			/* TLS does not have an unhash proto in SW cases,
@@ -537,9 +677,6 @@
 		return 0;
 	}
 
-	if (inet_csk_has_ulp(sk))
-		return -EINVAL;
-
 	if (sk->sk_family == AF_INET6) {
 		if (tcp_bpf_assert_proto_ops(psock->sk_proto))
 			return -EINVAL;
@@ -560,10 +697,9 @@
  */
 void tcp_bpf_clone(const struct sock *sk, struct sock *newsk)
 {
-	int family = sk->sk_family == AF_INET6 ? TCP_BPF_IPV6 : TCP_BPF_IPV4;
 	struct proto *prot = newsk->sk_prot;
 
-	if (prot == &tcp_bpf_prots[family][TCP_BPF_BASE])
+	if (is_insidevar(prot, tcp_bpf_prots))
 		newsk->sk_prot = sk->sk_prot_creator;
 }
 #endif /* CONFIG_BPF_SYSCALL */
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_cdg.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_cdg.c
@@ -161,8 +161,8 @@
 					      LINUX_MIB_TCPHYSTARTTRAINDETECT);
 				NET_ADD_STATS(sock_net(sk),
 					      LINUX_MIB_TCPHYSTARTTRAINCWND,
-					      tp->snd_cwnd);
-				tp->snd_ssthresh = tp->snd_cwnd;
+					      tcp_snd_cwnd(tp));
+				tp->snd_ssthresh = tcp_snd_cwnd(tp);
 				return;
 			}
 		}
@@ -180,8 +180,8 @@
 					      LINUX_MIB_TCPHYSTARTDELAYDETECT);
 				NET_ADD_STATS(sock_net(sk),
 					      LINUX_MIB_TCPHYSTARTDELAYCWND,
-					      tp->snd_cwnd);
-				tp->snd_ssthresh = tp->snd_cwnd;
+					      tcp_snd_cwnd(tp));
+				tp->snd_ssthresh = tcp_snd_cwnd(tp);
 			}
 		}
 	}
@@ -252,7 +252,7 @@
 			return false;
 	}
 
-	ca->shadow_wnd = max(ca->shadow_wnd, tp->snd_cwnd);
+	ca->shadow_wnd = max(ca->shadow_wnd, tcp_snd_cwnd(tp));
 	ca->state = CDG_BACKOFF;
 	tcp_enter_cwr(sk);
 	return true;
@@ -285,14 +285,14 @@
 	}
 
 	if (!tcp_is_cwnd_limited(sk)) {
-		ca->shadow_wnd = min(ca->shadow_wnd, tp->snd_cwnd);
+		ca->shadow_wnd = min(ca->shadow_wnd, tcp_snd_cwnd(tp));
 		return;
 	}
 
-	prior_snd_cwnd = tp->snd_cwnd;
+	prior_snd_cwnd = tcp_snd_cwnd(tp);
 	tcp_reno_cong_avoid(sk, ack, acked);
 
-	incr = tp->snd_cwnd - prior_snd_cwnd;
+	incr = tcp_snd_cwnd(tp) - prior_snd_cwnd;
 	ca->shadow_wnd = max(ca->shadow_wnd, ca->shadow_wnd + incr);
 }
 
@@ -331,15 +331,15 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 
 	if (ca->state == CDG_BACKOFF)
-		return max(2U, (tp->snd_cwnd * min(1024U, backoff_beta)) >> 10);
+		return max(2U, (tcp_snd_cwnd(tp) * min(1024U, backoff_beta)) >> 10);
 
 	if (ca->state == CDG_NONFULL && use_tolerance)
-		return tp->snd_cwnd;
+		return tcp_snd_cwnd(tp);
 
-	ca->shadow_wnd = min(ca->shadow_wnd >> 1, tp->snd_cwnd);
+	ca->shadow_wnd = min(ca->shadow_wnd >> 1, tcp_snd_cwnd(tp));
 	if (use_shadow)
-		return max3(2U, ca->shadow_wnd, tp->snd_cwnd >> 1);
-	return max(2U, tp->snd_cwnd >> 1);
+		return max3(2U, ca->shadow_wnd, tcp_snd_cwnd(tp) >> 1);
+	return max(2U, tcp_snd_cwnd(tp) >> 1);
 }
 
 static void tcp_cdg_cwnd_event(struct sock *sk, const enum tcp_ca_event ev)
@@ -357,7 +357,7 @@
 
 		ca->gradients = gradients;
 		ca->rtt_seq = tp->snd_nxt;
-		ca->shadow_wnd = tp->snd_cwnd;
+		ca->shadow_wnd = tcp_snd_cwnd(tp);
 		break;
 	case CA_EVENT_COMPLETE_CWR:
 		ca->state = CDG_UNKNOWN;
@@ -375,12 +375,13 @@
 	struct cdg *ca = inet_csk_ca(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
 
+	ca->gradients = NULL;
 	/* We silently fall back to window = 1 if allocation fails. */
 	if (window > 1)
 		ca->gradients = kcalloc(window, sizeof(ca->gradients[0]),
 					GFP_NOWAIT | __GFP_NOWARN);
 	ca->rtt_seq = tp->snd_nxt;
-	ca->shadow_wnd = tp->snd_cwnd;
+	ca->shadow_wnd = tcp_snd_cwnd(tp);
 }
 
 static void tcp_cdg_release(struct sock *sk)
@@ -388,6 +389,7 @@
 	struct cdg *ca = inet_csk_ca(sk);
 
 	kfree(ca->gradients);
+	ca->gradients = NULL;
 }
 
 static struct tcp_congestion_ops tcp_cdg __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_cong.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_cong.c
@@ -395,10 +395,10 @@
  */
 u32 tcp_slow_start(struct tcp_sock *tp, u32 acked)
 {
-	u32 cwnd = min(tp->snd_cwnd + acked, tp->snd_ssthresh);
+	u32 cwnd = min(tcp_snd_cwnd(tp) + acked, tp->snd_ssthresh);
 
-	acked -= cwnd - tp->snd_cwnd;
-	tp->snd_cwnd = min(cwnd, tp->snd_cwnd_clamp);
+	acked -= cwnd - tcp_snd_cwnd(tp);
+	tcp_snd_cwnd_set(tp, min(cwnd, tp->snd_cwnd_clamp));
 
 	return acked;
 }
@@ -412,7 +412,7 @@
 	/* If credits accumulated at a higher w, apply them gently now. */
 	if (tp->snd_cwnd_cnt >= w) {
 		tp->snd_cwnd_cnt = 0;
-		tp->snd_cwnd++;
+		tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 	}
 
 	tp->snd_cwnd_cnt += acked;
@@ -420,9 +420,9 @@
 		u32 delta = tp->snd_cwnd_cnt / w;
 
 		tp->snd_cwnd_cnt -= delta * w;
-		tp->snd_cwnd += delta;
+		tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + delta);
 	}
-	tp->snd_cwnd = min(tp->snd_cwnd, tp->snd_cwnd_clamp);
+	tcp_snd_cwnd_set(tp, min(tcp_snd_cwnd(tp), tp->snd_cwnd_clamp));
 }
 EXPORT_SYMBOL_GPL(tcp_cong_avoid_ai);
 
@@ -447,7 +447,7 @@
 			return;
 	}
 	/* In dangerous area, increase slowly. */
-	tcp_cong_avoid_ai(tp, tp->snd_cwnd, acked);
+	tcp_cong_avoid_ai(tp, tcp_snd_cwnd(tp), acked);
 }
 EXPORT_SYMBOL_GPL(tcp_reno_cong_avoid);
 
@@ -456,7 +456,7 @@
 {
 	const struct tcp_sock *tp = tcp_sk(sk);
 
-	return max(tp->snd_cwnd >> 1U, 2U);
+	return max(tcp_snd_cwnd(tp) >> 1U, 2U);
 }
 EXPORT_SYMBOL_GPL(tcp_reno_ssthresh);
 
@@ -464,7 +464,7 @@
 {
 	const struct tcp_sock *tp = tcp_sk(sk);
 
-	return max(tp->snd_cwnd, tp->prior_cwnd);
+	return max(tcp_snd_cwnd(tp), tp->prior_cwnd);
 }
 EXPORT_SYMBOL_GPL(tcp_reno_undo_cwnd);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_cubic.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_cubic.c
@@ -328,13 +328,11 @@
 		return;
 
 	if (tcp_in_slow_start(tp)) {
-		if (hystart && after(ack, ca->end_seq))
-			bictcp_hystart_reset(sk);
 		acked = tcp_slow_start(tp, acked);
 		if (!acked)
 			return;
 	}
-	bictcp_update(ca, tp->snd_cwnd, acked);
+	bictcp_update(ca, tcp_snd_cwnd(tp), acked);
 	tcp_cong_avoid_ai(tp, ca->cnt, acked);
 }
 
@@ -346,13 +344,13 @@
 	ca->epoch_start = 0;	/* end of epoch */
 
 	/* Wmax and fast convergence */
-	if (tp->snd_cwnd < ca->last_max_cwnd && fast_convergence)
-		ca->last_max_cwnd = (tp->snd_cwnd * (BICTCP_BETA_SCALE + beta))
+	if (tcp_snd_cwnd(tp) < ca->last_max_cwnd && fast_convergence)
+		ca->last_max_cwnd = (tcp_snd_cwnd(tp) * (BICTCP_BETA_SCALE + beta))
 			/ (2 * BICTCP_BETA_SCALE);
 	else
-		ca->last_max_cwnd = tp->snd_cwnd;
+		ca->last_max_cwnd = tcp_snd_cwnd(tp);
 
-	return max((tp->snd_cwnd * beta) / BICTCP_BETA_SCALE, 2U);
+	return max((tcp_snd_cwnd(tp) * beta) / BICTCP_BETA_SCALE, 2U);
 }
 
 static void cubictcp_state(struct sock *sk, u8 new_state)
@@ -389,6 +387,13 @@
 	struct bictcp *ca = inet_csk_ca(sk);
 	u32 threshold;
 
+	if (after(tp->snd_una, ca->end_seq))
+		bictcp_hystart_reset(sk);
+
+	/* hystart triggers when cwnd is larger than some threshold */
+	if (tcp_snd_cwnd(tp) < hystart_low_window)
+		return;
+
 	if (hystart_detect & HYSTART_ACK_TRAIN) {
 		u32 now = bictcp_clock_us(sk);
 
@@ -410,13 +415,13 @@
 				ca->found = 1;
 				pr_debug("hystart_ack_train (%u > %u) delay_min %u (+ ack_delay %u) cwnd %u\n",
 					 now - ca->round_start, threshold,
-					 ca->delay_min, hystart_ack_delay(sk), tp->snd_cwnd);
+					 ca->delay_min, hystart_ack_delay(sk), tcp_snd_cwnd(tp));
 				NET_INC_STATS(sock_net(sk),
 					      LINUX_MIB_TCPHYSTARTTRAINDETECT);
 				NET_ADD_STATS(sock_net(sk),
 					      LINUX_MIB_TCPHYSTARTTRAINCWND,
-					      tp->snd_cwnd);
-				tp->snd_ssthresh = tp->snd_cwnd;
+					      tcp_snd_cwnd(tp));
+				tp->snd_ssthresh = tcp_snd_cwnd(tp);
 			}
 		}
 	}
@@ -435,8 +440,8 @@
 					      LINUX_MIB_TCPHYSTARTDELAYDETECT);
 				NET_ADD_STATS(sock_net(sk),
 					      LINUX_MIB_TCPHYSTARTDELAYCWND,
-					      tp->snd_cwnd);
-				tp->snd_ssthresh = tp->snd_cwnd;
+					      tcp_snd_cwnd(tp));
+				tp->snd_ssthresh = tcp_snd_cwnd(tp);
 			}
 		}
 	}
@@ -464,9 +469,7 @@
 	if (ca->delay_min == 0 || ca->delay_min > delay)
 		ca->delay_min = delay;
 
-	/* hystart triggers when cwnd is larger than some threshold */
-	if (!ca->found && tcp_in_slow_start(tp) && hystart &&
-	    tp->snd_cwnd >= hystart_low_window)
+	if (!ca->found && tcp_in_slow_start(tp) && hystart)
 		hystart_update(sk, delay);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_dctcp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_dctcp.c
@@ -55,7 +55,18 @@
 };
 
 static unsigned int dctcp_shift_g __read_mostly = 4; /* g = 1/2^4 */
-module_param(dctcp_shift_g, uint, 0644);
+
+static int dctcp_shift_g_set(const char *val, const struct kernel_param *kp)
+{
+	return param_set_uint_minmax(val, kp, 0, 10);
+}
+
+static const struct kernel_param_ops dctcp_shift_g_ops = {
+	.set = dctcp_shift_g_set,
+	.get = param_get_uint,
+};
+
+module_param_cb(dctcp_shift_g, &dctcp_shift_g_ops, &dctcp_shift_g, 0644);
 MODULE_PARM_DESC(dctcp_shift_g, "parameter g for updating dctcp_alpha");
 
 static unsigned int dctcp_alpha_on_init __read_mostly = DCTCP_MAX_ALPHA;
@@ -104,8 +115,8 @@
 	struct dctcp *ca = inet_csk_ca(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
 
-	ca->loss_cwnd = tp->snd_cwnd;
-	return max(tp->snd_cwnd - ((tp->snd_cwnd * ca->dctcp_alpha) >> 11U), 2U);
+	ca->loss_cwnd = tcp_snd_cwnd(tp);
+	return max(tcp_snd_cwnd(tp) - ((tcp_snd_cwnd(tp) * ca->dctcp_alpha) >> 11U), 2U);
 }
 
 static void dctcp_update_alpha(struct sock *sk, u32 flags)
@@ -146,8 +157,8 @@
 	struct dctcp *ca = inet_csk_ca(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
 
-	ca->loss_cwnd = tp->snd_cwnd;
-	tp->snd_ssthresh = max(tp->snd_cwnd >> 1U, 2U);
+	ca->loss_cwnd = tcp_snd_cwnd(tp);
+	tp->snd_ssthresh = max(tcp_snd_cwnd(tp) >> 1U, 2U);
 }
 
 static void dctcp_state(struct sock *sk, u8 new_state)
@@ -209,8 +220,9 @@
 static u32 dctcp_cwnd_undo(struct sock *sk)
 {
 	const struct dctcp *ca = inet_csk_ca(sk);
+	struct tcp_sock *tp = tcp_sk(sk);
 
-	return max(tcp_sk(sk)->snd_cwnd, ca->loss_cwnd);
+	return max(tcp_snd_cwnd(tp), ca->loss_cwnd);
 }
 
 static struct tcp_congestion_ops dctcp __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_fastopen.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_fastopen.c
@@ -301,6 +301,7 @@
 static bool tcp_fastopen_queue_check(struct sock *sk)
 {
 	struct fastopen_queue *fastopenq;
+	int max_qlen;
 
 	/* Make sure the listener has enabled fastopen, and we don't
 	 * exceed the max # of pending TFO requests allowed before trying
@@ -313,10 +314,11 @@
 	 * temporarily vs a server not supporting Fast Open at all.
 	 */
 	fastopenq = &inet_csk(sk)->icsk_accept_queue.fastopenq;
-	if (fastopenq->max_qlen == 0)
+	max_qlen = READ_ONCE(fastopenq->max_qlen);
+	if (max_qlen == 0)
 		return false;
 
-	if (fastopenq->qlen >= fastopenq->max_qlen) {
+	if (fastopenq->qlen >= max_qlen) {
 		struct request_sock *req1;
 		spin_lock(&fastopenq->lock);
 		req1 = fastopenq->rskq_rst_head;
@@ -338,7 +340,7 @@
 				   const struct dst_entry *dst,
 				   int flag)
 {
-	return (sock_net(sk)->ipv4.sysctl_tcp_fastopen & flag) ||
+	return (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fastopen) & flag) ||
 	       tcp_sk(sk)->fastopen_no_cookie ||
 	       (dst && dst_metric(dst, RTAX_FASTOPEN_NO_COOKIE));
 }
@@ -353,7 +355,7 @@
 			      const struct dst_entry *dst)
 {
 	bool syn_data = TCP_SKB_CB(skb)->end_seq != TCP_SKB_CB(skb)->seq + 1;
-	int tcp_fastopen = sock_net(sk)->ipv4.sysctl_tcp_fastopen;
+	int tcp_fastopen = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fastopen);
 	struct tcp_fastopen_cookie valid_foc = { .len = -1 };
 	struct sock *child;
 	int ret = 0;
@@ -495,7 +497,7 @@
 {
 	struct net *net = sock_net(sk);
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_fastopen_blackhole_timeout)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fastopen_blackhole_timeout))
 		return;
 
 	/* Paired with READ_ONCE() in tcp_fastopen_active_should_disable() */
@@ -516,7 +518,8 @@
  */
 bool tcp_fastopen_active_should_disable(struct sock *sk)
 {
-	unsigned int tfo_bh_timeout = sock_net(sk)->ipv4.sysctl_tcp_fastopen_blackhole_timeout;
+	unsigned int tfo_bh_timeout =
+		READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_fastopen_blackhole_timeout);
 	unsigned long timeout;
 	int tfo_da_times;
 	int multiplier;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_highspeed.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_highspeed.c
@@ -127,22 +127,22 @@
 		 *     snd_cwnd <=
 		 *     hstcp_aimd_vals[ca->ai].cwnd
 		 */
-		if (tp->snd_cwnd > hstcp_aimd_vals[ca->ai].cwnd) {
-			while (tp->snd_cwnd > hstcp_aimd_vals[ca->ai].cwnd &&
+		if (tcp_snd_cwnd(tp) > hstcp_aimd_vals[ca->ai].cwnd) {
+			while (tcp_snd_cwnd(tp) > hstcp_aimd_vals[ca->ai].cwnd &&
 			       ca->ai < HSTCP_AIMD_MAX - 1)
 				ca->ai++;
-		} else if (ca->ai && tp->snd_cwnd <= hstcp_aimd_vals[ca->ai-1].cwnd) {
-			while (ca->ai && tp->snd_cwnd <= hstcp_aimd_vals[ca->ai-1].cwnd)
+		} else if (ca->ai && tcp_snd_cwnd(tp) <= hstcp_aimd_vals[ca->ai-1].cwnd) {
+			while (ca->ai && tcp_snd_cwnd(tp) <= hstcp_aimd_vals[ca->ai-1].cwnd)
 				ca->ai--;
 		}
 
 		/* Do additive increase */
-		if (tp->snd_cwnd < tp->snd_cwnd_clamp) {
+		if (tcp_snd_cwnd(tp) < tp->snd_cwnd_clamp) {
 			/* cwnd = cwnd + a(w) / cwnd */
 			tp->snd_cwnd_cnt += ca->ai + 1;
-			if (tp->snd_cwnd_cnt >= tp->snd_cwnd) {
-				tp->snd_cwnd_cnt -= tp->snd_cwnd;
-				tp->snd_cwnd++;
+			if (tp->snd_cwnd_cnt >= tcp_snd_cwnd(tp)) {
+				tp->snd_cwnd_cnt -= tcp_snd_cwnd(tp);
+				tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 			}
 		}
 	}
@@ -154,7 +154,7 @@
 	struct hstcp *ca = inet_csk_ca(sk);
 
 	/* Do multiplicative decrease */
-	return max(tp->snd_cwnd - ((tp->snd_cwnd * hstcp_aimd_vals[ca->ai].md) >> 8), 2U);
+	return max(tcp_snd_cwnd(tp) - ((tcp_snd_cwnd(tp) * hstcp_aimd_vals[ca->ai].md) >> 8), 2U);
 }
 
 static struct tcp_congestion_ops tcp_highspeed __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_htcp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_htcp.c
@@ -124,7 +124,7 @@
 
 	ca->packetcount += sample->pkts_acked;
 
-	if (ca->packetcount >= tp->snd_cwnd - (ca->alpha >> 7 ? : 1) &&
+	if (ca->packetcount >= tcp_snd_cwnd(tp) - (ca->alpha >> 7 ? : 1) &&
 	    now - ca->lasttime >= ca->minRTT &&
 	    ca->minRTT > 0) {
 		__u32 cur_Bi = ca->packetcount * HZ / (now - ca->lasttime);
@@ -225,7 +225,7 @@
 	const struct htcp *ca = inet_csk_ca(sk);
 
 	htcp_param_update(sk);
-	return max((tp->snd_cwnd * ca->beta) >> 7, 2U);
+	return max((tcp_snd_cwnd(tp) * ca->beta) >> 7, 2U);
 }
 
 static void htcp_cong_avoid(struct sock *sk, u32 ack, u32 acked)
@@ -242,9 +242,9 @@
 		/* In dangerous area, increase slowly.
 		 * In theory this is tp->snd_cwnd += alpha / tp->snd_cwnd
 		 */
-		if ((tp->snd_cwnd_cnt * ca->alpha)>>7 >= tp->snd_cwnd) {
-			if (tp->snd_cwnd < tp->snd_cwnd_clamp)
-				tp->snd_cwnd++;
+		if ((tp->snd_cwnd_cnt * ca->alpha)>>7 >= tcp_snd_cwnd(tp)) {
+			if (tcp_snd_cwnd(tp) < tp->snd_cwnd_clamp)
+				tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 			tp->snd_cwnd_cnt = 0;
 			htcp_alpha_update(ca);
 		} else
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_hybla.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_hybla.c
@@ -54,7 +54,7 @@
 	ca->rho2_7ls = 0;
 	ca->snd_cwnd_cents = 0;
 	ca->hybla_en = true;
-	tp->snd_cwnd = 2;
+	tcp_snd_cwnd_set(tp, 2);
 	tp->snd_cwnd_clamp = 65535;
 
 	/* 1st Rho measurement based on initial srtt */
@@ -62,7 +62,7 @@
 
 	/* set minimum rtt as this is the 1st ever seen */
 	ca->minrtt_us = tp->srtt_us;
-	tp->snd_cwnd = ca->rho;
+	tcp_snd_cwnd_set(tp, ca->rho);
 }
 
 static void hybla_state(struct sock *sk, u8 ca_state)
@@ -137,31 +137,31 @@
 		 * as long as increment is estimated as (rho<<7)/window
 		 * it already is <<7 and we can easily count its fractions.
 		 */
-		increment = ca->rho2_7ls / tp->snd_cwnd;
+		increment = ca->rho2_7ls / tcp_snd_cwnd(tp);
 		if (increment < 128)
 			tp->snd_cwnd_cnt++;
 	}
 
 	odd = increment % 128;
-	tp->snd_cwnd += increment >> 7;
+	tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + (increment >> 7));
 	ca->snd_cwnd_cents += odd;
 
 	/* check when fractions goes >=128 and increase cwnd by 1. */
 	while (ca->snd_cwnd_cents >= 128) {
-		tp->snd_cwnd++;
+		tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 		ca->snd_cwnd_cents -= 128;
 		tp->snd_cwnd_cnt = 0;
 	}
 	/* check when cwnd has not been incremented for a while */
-	if (increment == 0 && odd == 0 && tp->snd_cwnd_cnt >= tp->snd_cwnd) {
-		tp->snd_cwnd++;
+	if (increment == 0 && odd == 0 && tp->snd_cwnd_cnt >= tcp_snd_cwnd(tp)) {
+		tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 		tp->snd_cwnd_cnt = 0;
 	}
 	/* clamp down slowstart cwnd to ssthresh value. */
 	if (is_slowstart)
-		tp->snd_cwnd = min(tp->snd_cwnd, tp->snd_ssthresh);
+		tcp_snd_cwnd_set(tp, min(tcp_snd_cwnd(tp), tp->snd_ssthresh));
 
-	tp->snd_cwnd = min_t(u32, tp->snd_cwnd, tp->snd_cwnd_clamp);
+	tcp_snd_cwnd_set(tp, min(tcp_snd_cwnd(tp), tp->snd_cwnd_clamp));
 }
 
 static struct tcp_congestion_ops tcp_hybla __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_illinois.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_illinois.c
@@ -224,7 +224,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct illinois *ca = inet_csk_ca(sk);
 
-	if (tp->snd_cwnd < win_thresh) {
+	if (tcp_snd_cwnd(tp) < win_thresh) {
 		ca->alpha = ALPHA_BASE;
 		ca->beta = BETA_BASE;
 	} else if (ca->cnt_rtt > 0) {
@@ -284,9 +284,9 @@
 		 * tp->snd_cwnd += alpha/tp->snd_cwnd
 		*/
 		delta = (tp->snd_cwnd_cnt * ca->alpha) >> ALPHA_SHIFT;
-		if (delta >= tp->snd_cwnd) {
-			tp->snd_cwnd = min(tp->snd_cwnd + delta / tp->snd_cwnd,
-					   (u32)tp->snd_cwnd_clamp);
+		if (delta >= tcp_snd_cwnd(tp)) {
+			tcp_snd_cwnd_set(tp, min(tcp_snd_cwnd(tp) + delta / tcp_snd_cwnd(tp),
+						 (u32)tp->snd_cwnd_clamp));
 			tp->snd_cwnd_cnt = 0;
 		}
 	}
@@ -296,9 +296,11 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct illinois *ca = inet_csk_ca(sk);
+	u32 decr;
 
 	/* Multiplicative decrease */
-	return max(tp->snd_cwnd - ((tp->snd_cwnd * ca->beta) >> BETA_SHIFT), 2U);
+	decr = (tcp_snd_cwnd(tp) * ca->beta) >> BETA_SHIFT;
+	return max(tcp_snd_cwnd(tp) - decr, 2U);
 }
 
 /* Extract info for Tcp socket info provided via netlink. */
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_input.c
@@ -243,6 +243,19 @@
 		if (unlikely(len > icsk->icsk_ack.rcv_mss +
 				   MAX_TCP_OPTION_SPACE))
 			tcp_gro_dev_warn(sk, skb, len);
+		/* If the skb has a len of exactly 1*MSS and has the PSH bit
+		 * set then it is likely the end of an application write. So
+		 * more data may not be arriving soon, and yet the data sender
+		 * may be waiting for an ACK if cwnd-bound or using TX zero
+		 * copy. So we set ICSK_ACK_PUSHED here so that
+		 * tcp_cleanup_rbuf() will send an ACK immediately if the app
+		 * reads all of the data and is not ping-pong. If len > MSS
+		 * then this logic does not matter (and does not hurt) because
+		 * tcp_cleanup_rbuf() will always ACK immediately if the app
+		 * reads data and there is more than an MSS of unACKed data.
+		 */
+		if (TCP_SKB_CB(skb)->tcp_flags & TCPHDR_PSH)
+			icsk->icsk_ack.pending |= ICSK_ACK_PUSHED;
 	} else {
 		/* Otherwise, we make more careful check taking into account,
 		 * that SACKs block is variable.
@@ -287,7 +300,7 @@
 		icsk->icsk_ack.quick = quickacks;
 }
 
-void tcp_enter_quickack_mode(struct sock *sk, unsigned int max_quickacks)
+static void tcp_enter_quickack_mode(struct sock *sk, unsigned int max_quickacks)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 
@@ -295,7 +308,6 @@
 	inet_csk_exit_pingpong_mode(sk);
 	icsk->icsk_ack.ato = TCP_ATO_MIN;
 }
-EXPORT_SYMBOL(tcp_enter_quickack_mode);
 
 /* Send ACKs quickly, if "quick" count is not exhausted
  * and the session is not interactive.
@@ -414,7 +426,7 @@
 	per_mss = roundup_pow_of_two(per_mss) +
 		  SKB_DATA_ALIGN(sizeof(struct sk_buff));
 
-	nr_segs = max_t(u32, TCP_INIT_CWND, tp->snd_cwnd);
+	nr_segs = max_t(u32, TCP_INIT_CWND, tcp_snd_cwnd(tp));
 	nr_segs = max_t(u32, nr_segs, tp->reordering + 1);
 
 	/* Fast Recovery (RFC 5681 3.2) :
@@ -426,7 +438,7 @@
 
 	if (sk->sk_sndbuf < sndmem)
 		WRITE_ONCE(sk->sk_sndbuf,
-			   min(sndmem, sock_net(sk)->ipv4.sysctl_tcp_wmem[2]));
+			   min(sndmem, READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_wmem[2])));
 }
 
 /* 2. Tuning advertised window (window_clamp, rcv_ssthresh)
@@ -461,7 +473,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	/* Optimize this! */
 	int truesize = tcp_win_from_space(sk, skbtruesize) >> 1;
-	int window = tcp_win_from_space(sk, sock_net(sk)->ipv4.sysctl_tcp_rmem[2]) >> 1;
+	int window = tcp_win_from_space(sk, READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[2])) >> 1;
 
 	while (tp->rcv_ssthresh <= window) {
 		if (truesize <= skb->len)
@@ -526,7 +538,7 @@
  */
 static void tcp_init_buffer_space(struct sock *sk)
 {
-	int tcp_app_win = sock_net(sk)->ipv4.sysctl_tcp_app_win;
+	int tcp_app_win = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_app_win);
 	struct tcp_sock *tp = tcp_sk(sk);
 	int maxwin;
 
@@ -566,16 +578,17 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct net *net = sock_net(sk);
+	int rmem2;
 
 	icsk->icsk_ack.quick = 0;
+	rmem2 = READ_ONCE(net->ipv4.sysctl_tcp_rmem[2]);
 
-	if (sk->sk_rcvbuf < net->ipv4.sysctl_tcp_rmem[2] &&
+	if (sk->sk_rcvbuf < rmem2 &&
 	    !(sk->sk_userlocks & SOCK_RCVBUF_LOCK) &&
 	    !tcp_under_memory_pressure(sk) &&
 	    sk_memory_allocated(sk) < sk_prot_mem_limits(sk, 0)) {
 		WRITE_ONCE(sk->sk_rcvbuf,
-			   min(atomic_read(&sk->sk_rmem_alloc),
-			       net->ipv4.sysctl_tcp_rmem[2]));
+			   min(atomic_read(&sk->sk_rmem_alloc), rmem2));
 	}
 	if (atomic_read(&sk->sk_rmem_alloc) > sk->sk_rcvbuf)
 		tp->rcv_ssthresh = min(tp->window_clamp, 2U * tp->advmss);
@@ -716,7 +729,7 @@
 	 * <prev RTT . ><current RTT .. ><next RTT .... >
 	 */
 
-	if (sock_net(sk)->ipv4.sysctl_tcp_moderate_rcvbuf &&
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_moderate_rcvbuf) &&
 	    !(sk->sk_userlocks & SOCK_RCVBUF_LOCK)) {
 		int rcvmem, rcvbuf;
 		u64 rcvwin, grow;
@@ -737,7 +750,7 @@
 
 		do_div(rcvwin, tp->advmss);
 		rcvbuf = min_t(u64, rcvwin * rcvmem,
-			       sock_net(sk)->ipv4.sysctl_tcp_rmem[2]);
+			       READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[2]));
 		if (rcvbuf > sk->sk_rcvbuf) {
 			WRITE_ONCE(sk->sk_rcvbuf, rcvbuf);
 
@@ -901,12 +914,12 @@
 	 *	 If snd_cwnd >= (tp->snd_ssthresh / 2), we are approaching
 	 *	 end of slow start and should slow down.
 	 */
-	if (tp->snd_cwnd < tp->snd_ssthresh / 2)
-		rate *= sock_net(sk)->ipv4.sysctl_tcp_pacing_ss_ratio;
+	if (tcp_snd_cwnd(tp) < tp->snd_ssthresh / 2)
+		rate *= READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_pacing_ss_ratio);
 	else
-		rate *= sock_net(sk)->ipv4.sysctl_tcp_pacing_ca_ratio;
+		rate *= READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_pacing_ca_ratio);
 
-	rate *= max(tp->snd_cwnd, tp->packets_out);
+	rate *= max(tcp_snd_cwnd(tp), tp->packets_out);
 
 	if (likely(tp->srtt_us))
 		do_div(rate, tp->srtt_us);
@@ -1043,7 +1056,7 @@
 			 tp->undo_marker ? tp->undo_retrans : 0);
 #endif
 		tp->reordering = min_t(u32, (metric + mss - 1) / mss,
-				       sock_net(sk)->ipv4.sysctl_tcp_max_reordering);
+				       READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_max_reordering));
 	}
 
 	/* This exciting event is worth to be remembered. 8) */
@@ -1652,6 +1665,8 @@
 	    (mss != tcp_skb_seglen(skb)))
 		goto out;
 
+	if (!tcp_skb_can_collapse(prev, skb))
+		goto out;
 	len = skb->len;
 	pcount = tcp_skb_pcount(skb);
 	if (tcp_skb_shift(prev, skb, pcount, len))
@@ -2020,7 +2035,7 @@
 		return;
 
 	tp->reordering = min_t(u32, tp->packets_out + addend,
-			       sock_net(sk)->ipv4.sysctl_tcp_max_reordering);
+			       READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_max_reordering));
 	tp->reord_seen++;
 	NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPRENOREORDER);
 }
@@ -2079,13 +2094,22 @@
 static inline void tcp_init_undo(struct tcp_sock *tp)
 {
 	tp->undo_marker = tp->snd_una;
+
 	/* Retransmission still in flight may cause DSACKs later. */
-	tp->undo_retrans = tp->retrans_out ? : -1;
+	/* First, account for regular retransmits in flight: */
+	tp->undo_retrans = tp->retrans_out;
+	/* Next, account for TLP retransmits in flight: */
+	if (tp->tlp_high_seq && tp->tlp_retrans)
+		tp->undo_retrans++;
+	/* Finally, avoid 0, because undo_retrans==0 means "can undo now": */
+	if (!tp->undo_retrans)
+		tp->undo_retrans = -1;
 }
 
 static bool tcp_is_rack(const struct sock *sk)
 {
-	return sock_net(sk)->ipv4.sysctl_tcp_recovery & TCP_RACK_LOSS_DETECTION;
+	return READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_recovery) &
+		TCP_RACK_LOSS_DETECTION;
 }
 
 /* If we detect SACK reneging, forget all SACK information
@@ -2129,6 +2153,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct net *net = sock_net(sk);
 	bool new_recovery = icsk->icsk_ca_state < TCP_CA_Recovery;
+	u8 reordering;
 
 	tcp_timeout_mark_lost(sk);
 
@@ -2137,31 +2162,34 @@
 	    !after(tp->high_seq, tp->snd_una) ||
 	    (icsk->icsk_ca_state == TCP_CA_Loss && !icsk->icsk_retransmits)) {
 		tp->prior_ssthresh = tcp_current_ssthresh(sk);
-		tp->prior_cwnd = tp->snd_cwnd;
+		tp->prior_cwnd = tcp_snd_cwnd(tp);
 		tp->snd_ssthresh = icsk->icsk_ca_ops->ssthresh(sk);
 		tcp_ca_event(sk, CA_EVENT_LOSS);
 		tcp_init_undo(tp);
 	}
-	tp->snd_cwnd	   = tcp_packets_in_flight(tp) + 1;
+	tcp_snd_cwnd_set(tp, tcp_packets_in_flight(tp) + 1);
 	tp->snd_cwnd_cnt   = 0;
 	tp->snd_cwnd_stamp = tcp_jiffies32;
 
 	/* Timeout in disordered state after receiving substantial DUPACKs
 	 * suggests that the degree of reordering is over-estimated.
 	 */
+	reordering = READ_ONCE(net->ipv4.sysctl_tcp_reordering);
 	if (icsk->icsk_ca_state <= TCP_CA_Disorder &&
-	    tp->sacked_out >= net->ipv4.sysctl_tcp_reordering)
+	    tp->sacked_out >= reordering)
 		tp->reordering = min_t(unsigned int, tp->reordering,
-				       net->ipv4.sysctl_tcp_reordering);
+				       reordering);
+
 	tcp_set_ca_state(sk, TCP_CA_Loss);
 	tp->high_seq = tp->snd_nxt;
+	tp->tlp_high_seq = 0;
 	tcp_ecn_queue_cwr(tp);
 
 	/* F-RTO RFC5682 sec 3.1 step 1: retransmit SND.UNA if no previous
 	 * loss recovery is underway except recurring timeout(s) on
 	 * the same SND.UNA (sec 3.2). Disable F-RTO on path MTU probing
 	 */
-	tp->frto = net->ipv4.sysctl_tcp_frto &&
+	tp->frto = READ_ONCE(net->ipv4.sysctl_tcp_frto) &&
 		   (new_recovery || icsk->icsk_retransmits) &&
 		   !inet_csk(sk)->icsk_mtup.probe_size;
 }
@@ -2176,15 +2204,17 @@
  * restore sanity to the SACK scoreboard. If the apparent reneging
  * persists until this RTO then we'll clear the SACK scoreboard.
  */
-static bool tcp_check_sack_reneging(struct sock *sk, int flag)
+static bool tcp_check_sack_reneging(struct sock *sk, int *ack_flag)
 {
-	if (flag & FLAG_SACK_RENEGING) {
+	if (*ack_flag & FLAG_SACK_RENEGING &&
+	    *ack_flag & FLAG_SND_UNA_ADVANCED) {
 		struct tcp_sock *tp = tcp_sk(sk);
 		unsigned long delay = max(usecs_to_jiffies(tp->srtt_us >> 4),
 					  msecs_to_jiffies(10));
 
 		inet_csk_reset_xmit_timer(sk, ICSK_TIME_RETRANS,
 					  delay, TCP_RTO_MAX);
+		*ack_flag &= ~FLAG_SET_XMIT_TIMER;
 		return true;
 	}
 	return false;
@@ -2403,8 +2433,22 @@
  */
 static inline bool tcp_packet_delayed(const struct tcp_sock *tp)
 {
-	return tp->retrans_stamp &&
-	       tcp_tsopt_ecr_before(tp, tp->retrans_stamp);
+	const struct sock *sk = (const struct sock *)tp;
+
+	if (tp->retrans_stamp &&
+	    tcp_tsopt_ecr_before(tp, tp->retrans_stamp))
+		return true;  /* got echoed TS before first retransmission */
+
+	/* Check if nothing was retransmitted (retrans_stamp==0), which may
+	 * happen in fast recovery due to TSQ. But we ignore zero retrans_stamp
+	 * in TCP_SYN_SENT, since when we set FLAG_SYN_ACKED we also clear
+	 * retrans_stamp even if we had retransmitted the SYN.
+	 */
+	if (!tp->retrans_stamp &&	   /* no record of a retransmit/SYN? */
+	    sk->sk_state != TCP_SYN_SENT)  /* not the FLAG_SYN_ACKED case? */
+		return true;  /* nothing was retransmitted */
+
+	return false;
 }
 
 /* Undo procedures. */
@@ -2438,6 +2482,16 @@
 	return false;
 }
 
+/* If loss recovery is finished and there are no retransmits out in the
+ * network, then we clear retrans_stamp so that upon the next loss recovery
+ * retransmits_timed_out() and timestamp-undo are using the correct value.
+ */
+static void tcp_retrans_stamp_cleanup(struct sock *sk)
+{
+	if (!tcp_any_retrans_done(sk))
+		tcp_sk(sk)->retrans_stamp = 0;
+}
+
 static void DBGUNDO(struct sock *sk, const char *msg)
 {
 #if FASTRETRANS_DEBUG > 1
@@ -2448,7 +2502,7 @@
 		pr_debug("Undo %s %pI4/%u c%u l%u ss%u/%u p%u\n",
 			 msg,
 			 &inet->inet_daddr, ntohs(inet->inet_dport),
-			 tp->snd_cwnd, tcp_left_out(tp),
+			 tcp_snd_cwnd(tp), tcp_left_out(tp),
 			 tp->snd_ssthresh, tp->prior_ssthresh,
 			 tp->packets_out);
 	}
@@ -2457,7 +2511,7 @@
 		pr_debug("Undo %s %pI6/%u c%u l%u ss%u/%u p%u\n",
 			 msg,
 			 &sk->sk_v6_daddr, ntohs(inet->inet_dport),
-			 tp->snd_cwnd, tcp_left_out(tp),
+			 tcp_snd_cwnd(tp), tcp_left_out(tp),
 			 tp->snd_ssthresh, tp->prior_ssthresh,
 			 tp->packets_out);
 	}
@@ -2482,7 +2536,7 @@
 	if (tp->prior_ssthresh) {
 		const struct inet_connection_sock *icsk = inet_csk(sk);
 
-		tp->snd_cwnd = icsk->icsk_ca_ops->undo_cwnd(sk);
+		tcp_snd_cwnd_set(tp, icsk->icsk_ca_ops->undo_cwnd(sk));
 
 		if (tp->prior_ssthresh > tp->snd_ssthresh) {
 			tp->snd_ssthresh = tp->prior_ssthresh;
@@ -2499,6 +2553,21 @@
 	return tp->undo_marker && (!tp->undo_retrans || tcp_packet_delayed(tp));
 }
 
+static bool tcp_is_non_sack_preventing_reopen(struct sock *sk)
+{
+	struct tcp_sock *tp = tcp_sk(sk);
+
+	if (tp->snd_una == tp->high_seq && tcp_is_reno(tp)) {
+		/* Hold old state until something *above* high_seq
+		 * is ACKed. For Reno it is MUST to prevent false
+		 * fast retransmits (RFC2582). SACK TCP is safe. */
+		if (!tcp_any_retrans_done(sk))
+			tp->retrans_stamp = 0;
+		return true;
+	}
+	return false;
+}
+
 /* People celebrate: "We love our President!" */
 static bool tcp_try_undo_recovery(struct sock *sk)
 {
@@ -2521,14 +2590,8 @@
 	} else if (tp->rack.reo_wnd_persist) {
 		tp->rack.reo_wnd_persist--;
 	}
-	if (tp->snd_una == tp->high_seq && tcp_is_reno(tp)) {
-		/* Hold old state until something *above* high_seq
-		 * is ACKed. For Reno it is MUST to prevent false
-		 * fast retransmits (RFC2582). SACK TCP is safe. */
-		if (!tcp_any_retrans_done(sk))
-			tp->retrans_stamp = 0;
+	if (tcp_is_non_sack_preventing_reopen(sk))
 		return true;
-	}
 	tcp_set_ca_state(sk, TCP_CA_Open);
 	tp->is_sack_reneg = 0;
 	return false;
@@ -2564,6 +2627,8 @@
 			NET_INC_STATS(sock_net(sk),
 					LINUX_MIB_TCPSPURIOUSRTOS);
 		inet_csk(sk)->icsk_retransmits = 0;
+		if (tcp_is_non_sack_preventing_reopen(sk))
+			return true;
 		if (frto_undo || tcp_is_sack(tp)) {
 			tcp_set_ca_state(sk, TCP_CA_Open);
 			tp->is_sack_reneg = 0;
@@ -2589,7 +2654,7 @@
 	tp->high_seq = tp->snd_nxt;
 	tp->tlp_high_seq = 0;
 	tp->snd_cwnd_cnt = 0;
-	tp->prior_cwnd = tp->snd_cwnd;
+	tp->prior_cwnd = tcp_snd_cwnd(tp);
 	tp->prr_delivered = 0;
 	tp->prr_out = 0;
 	tp->snd_ssthresh = inet_csk(sk)->icsk_ca_ops->ssthresh(sk);
@@ -2619,7 +2684,7 @@
 	}
 	/* Force a fast retransmit upon entering fast recovery */
 	sndcnt = max(sndcnt, (tp->prr_out ? 0 : 1));
-	tp->snd_cwnd = tcp_packets_in_flight(tp) + sndcnt;
+	tcp_snd_cwnd_set(tp, tcp_packets_in_flight(tp) + sndcnt);
 }
 
 static inline void tcp_end_cwnd_reduction(struct sock *sk)
@@ -2632,7 +2697,7 @@
 	/* Reset cwnd to ssthresh in CWR or Recovery (unless it's undone) */
 	if (tp->snd_ssthresh < TCP_INFINITE_SSTHRESH &&
 	    (inet_csk(sk)->icsk_ca_state == TCP_CA_CWR || tp->undo_marker)) {
-		tp->snd_cwnd = tp->snd_ssthresh;
+		tcp_snd_cwnd_set(tp, tp->snd_ssthresh);
 		tp->snd_cwnd_stamp = tcp_jiffies32;
 	}
 	tcp_ca_event(sk, CA_EVENT_COMPLETE_CWR);
@@ -2696,12 +2761,15 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct inet_connection_sock *icsk = inet_csk(sk);
+	u64 val;
 
-	/* FIXME: breaks with very large cwnd */
 	tp->prior_ssthresh = tcp_current_ssthresh(sk);
-	tp->snd_cwnd = tp->snd_cwnd *
-		       tcp_mss_to_mtu(sk, tp->mss_cache) /
-		       icsk->icsk_mtup.probe_size;
+
+	val = (u64)tcp_snd_cwnd(tp) * tcp_mss_to_mtu(sk, tp->mss_cache);
+	do_div(val, icsk->icsk_mtup.probe_size);
+	WARN_ON_ONCE((u32)val != val);
+	tcp_snd_cwnd_set(tp, max_t(u32, 1U, val));
+
 	tp->snd_cwnd_cnt = 0;
 	tp->snd_cwnd_stamp = tcp_jiffies32;
 	tp->snd_ssthresh = tcp_current_ssthresh(sk);
@@ -2712,13 +2780,37 @@
 	NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPMTUPSUCCESS);
 }
 
+/* Sometimes we deduce that packets have been dropped due to reasons other than
+ * congestion, like path MTU reductions or failed client TFO attempts. In these
+ * cases we call this function to retransmit as many packets as cwnd allows,
+ * without reducing cwnd. Given that retransmits will set retrans_stamp to a
+ * non-zero value (and may do so in a later calling context due to TSQ), we
+ * also enter CA_Loss so that we track when all retransmitted packets are ACKed
+ * and clear retrans_stamp when that happens (to ensure later recurring RTOs
+ * are using the correct retrans_stamp and don't declare ETIMEDOUT
+ * prematurely).
+ */
+static void tcp_non_congestion_loss_retransmit(struct sock *sk)
+{
+	const struct inet_connection_sock *icsk = inet_csk(sk);
+	struct tcp_sock *tp = tcp_sk(sk);
+
+	if (icsk->icsk_ca_state != TCP_CA_Loss) {
+		tp->high_seq = tp->snd_nxt;
+		tp->snd_ssthresh = tcp_current_ssthresh(sk);
+		tp->prior_ssthresh = 0;
+		tp->undo_marker = 0;
+		tcp_set_ca_state(sk, TCP_CA_Loss);
+	}
+	tcp_xmit_retransmit_queue(sk);
+}
+
 /* Do a simple retransmit without using the backoff mechanisms in
  * tcp_timer. This is used for path mtu discovery.
  * The socket is already locked here.
  */
 void tcp_simple_retransmit(struct sock *sk)
 {
-	const struct inet_connection_sock *icsk = inet_csk(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct sk_buff *skb;
 	int mss;
@@ -2758,14 +2850,7 @@
 	 * in network, but units changed and effective
 	 * cwnd/ssthresh really reduced now.
 	 */
-	if (icsk->icsk_ca_state != TCP_CA_Loss) {
-		tp->high_seq = tp->snd_nxt;
-		tp->snd_ssthresh = tcp_current_ssthresh(sk);
-		tp->prior_ssthresh = 0;
-		tp->undo_marker = 0;
-		tcp_set_ca_state(sk, TCP_CA_Loss);
-	}
-	tcp_xmit_retransmit_queue(sk);
+	tcp_non_congestion_loss_retransmit(sk);
 }
 EXPORT_SYMBOL(tcp_simple_retransmit);
 
@@ -2774,6 +2859,9 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	int mib_idx;
 
+	/* Start the clock with our fast retransmit, for undo and ETIMEDOUT. */
+	tcp_retrans_stamp_cleanup(sk);
+
 	if (tcp_is_reno(tp))
 		mib_idx = LINUX_MIB_TCPRENORECOVERY;
 	else
@@ -2940,7 +3028,7 @@
 		tp->prior_ssthresh = 0;
 
 	/* B. In all the states check for reneging SACKs. */
-	if (tcp_check_sack_reneging(sk, flag))
+	if (tcp_check_sack_reneging(sk, ack_flag))
 		return;
 
 	/* C. Check consistency of the current state. */
@@ -2982,7 +3070,7 @@
 			return;
 
 		if (tcp_try_undo_dsack(sk))
-			tcp_try_keep_open(sk);
+			tcp_try_to_open(sk, flag);
 
 		tcp_identify_packet_loss(sk, ack_flag);
 		if (icsk->icsk_ca_state != TCP_CA_Recovery) {
@@ -3024,7 +3112,7 @@
 		    tp->snd_una == tp->mtu_probe.probe_seq_start) {
 			tcp_mtup_probe_failed(sk);
 			/* Restores the reduction we did in tcp_mtup_probe() */
-			tp->snd_cwnd++;
+			tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 			tcp_simple_retransmit(sk);
 			return;
 		}
@@ -3041,7 +3129,7 @@
 
 static void tcp_update_rtt_min(struct sock *sk, u32 rtt_us, const int flag)
 {
-	u32 wlen = sock_net(sk)->ipv4.sysctl_tcp_min_rtt_wlen * HZ;
+	u32 wlen = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_min_rtt_wlen) * HZ;
 	struct tcp_sock *tp = tcp_sk(sk);
 
 	if ((flag & FLAG_ACK_MAYBE_DELAYED) && rtt_us > tcp_min_rtt(tp)) {
@@ -3452,7 +3540,8 @@
 	 * new SACK or ECE mark may first advance cwnd here and later reduce
 	 * cwnd in tcp_fastretrans_alert() based on more states.
 	 */
-	if (tcp_sk(sk)->reordering > sock_net(sk)->ipv4.sysctl_tcp_reordering)
+	if (tcp_sk(sk)->reordering >
+	    READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_reordering))
 		return flag & FLAG_FORWARD_PROGRESS;
 
 	return flag & FLAG_DATA_ACKED;
@@ -3561,16 +3650,23 @@
 static bool __tcp_oow_rate_limited(struct net *net, int mib_idx,
 				   u32 *last_oow_ack_time)
 {
-	if (*last_oow_ack_time) {
-		s32 elapsed = (s32)(tcp_jiffies32 - *last_oow_ack_time);
+	/* Paired with the WRITE_ONCE() in this function. */
+	u32 val = READ_ONCE(*last_oow_ack_time);
 
-		if (0 <= elapsed && elapsed < net->ipv4.sysctl_tcp_invalid_ratelimit) {
+	if (val) {
+		s32 elapsed = (s32)(tcp_jiffies32 - val);
+
+		if (0 <= elapsed &&
+		    elapsed < READ_ONCE(net->ipv4.sysctl_tcp_invalid_ratelimit)) {
 			NET_INC_STATS(net, mib_idx);
 			return true;	/* rate-limited: don't send yet! */
 		}
 	}
 
-	*last_oow_ack_time = tcp_jiffies32;
+	/* Paired with the prior READ_ONCE() and with itself,
+	 * as we might be lockless.
+	 */
+	WRITE_ONCE(*last_oow_ack_time, tcp_jiffies32);
 
 	return false;	/* not rate-limited: go ahead, send dupack now! */
 }
@@ -3611,11 +3707,11 @@
 
 	/* Then check host-wide RFC 5961 rate limit. */
 	now = jiffies / HZ;
-	if (now != challenge_timestamp) {
-		u32 ack_limit = net->ipv4.sysctl_tcp_challenge_ack_limit;
+	if (now != READ_ONCE(challenge_timestamp)) {
+		u32 ack_limit = READ_ONCE(net->ipv4.sysctl_tcp_challenge_ack_limit);
 		u32 half = (ack_limit + 1) >> 1;
 
-		challenge_timestamp = now;
+		WRITE_ONCE(challenge_timestamp, now);
 		WRITE_ONCE(challenge_count, half + prandom_u32_max(ack_limit));
 	}
 	count = READ_ONCE(challenge_count);
@@ -3753,8 +3849,12 @@
 	 * then we can probably ignore it.
 	 */
 	if (before(ack, prior_snd_una)) {
+		u32 max_window;
+
+		/* do not accept ACK for bytes we never sent. */
+		max_window = min_t(u64, tp->max_window, tp->bytes_acked);
 		/* RFC 5961 5.2 [Blind Data Injection Attack].[Mitigation] */
-		if (before(ack, prior_snd_una - tp->max_window)) {
+		if (before(ack, prior_snd_una - max_window)) {
 			if (!(flag & FLAG_NO_CHALLENGE_ACK))
 				tcp_send_challenge_ack(sk, skb);
 			return -1;
@@ -3842,7 +3942,7 @@
 	/* We passed data and got it acked, remove any soft error
 	 * log. Something worked...
 	 */
-	sk->sk_err_soft = 0;
+	WRITE_ONCE(sk->sk_err_soft, 0);
 	icsk->icsk_probes_out = 0;
 	tp->rcv_tstamp = tcp_jiffies32;
 	if (!prior_packets)
@@ -3858,7 +3958,8 @@
 		tcp_process_tlp_ack(sk, ack, flag);
 
 	if (tcp_ack_is_dubious(sk, flag)) {
-		if (!(flag & (FLAG_SND_UNA_ADVANCED | FLAG_NOT_DUP))) {
+		if (!(flag & (FLAG_SND_UNA_ADVANCED |
+			      FLAG_NOT_DUP | FLAG_DSACKING_ACK))) {
 			num_dupack = 1;
 			/* Consider if pure acks were aggregated in tcp_add_backlog() */
 			if (!(flag & FLAG_DATA))
@@ -4043,7 +4144,7 @@
 				break;
 			case TCPOPT_WINDOW:
 				if (opsize == TCPOLEN_WINDOW && th->syn &&
-				    !estab && net->ipv4.sysctl_tcp_window_scaling) {
+				    !estab && READ_ONCE(net->ipv4.sysctl_tcp_window_scaling)) {
 					__u8 snd_wscale = *(__u8 *)ptr;
 					opt_rx->wscale_ok = 1;
 					if (snd_wscale > TCP_MAX_WSCALE) {
@@ -4059,7 +4160,7 @@
 			case TCPOPT_TIMESTAMP:
 				if ((opsize == TCPOLEN_TIMESTAMP) &&
 				    ((estab && opt_rx->tstamp_ok) ||
-				     (!estab && net->ipv4.sysctl_tcp_timestamps))) {
+				     (!estab && READ_ONCE(net->ipv4.sysctl_tcp_timestamps)))) {
 					opt_rx->saw_tstamp = 1;
 					opt_rx->rcv_tsval = get_unaligned_be32(ptr);
 					opt_rx->rcv_tsecr = get_unaligned_be32(ptr + 4);
@@ -4067,7 +4168,7 @@
 				break;
 			case TCPOPT_SACK_PERM:
 				if (opsize == TCPOLEN_SACK_PERM && th->syn &&
-				    !estab && net->ipv4.sysctl_tcp_sack) {
+				    !estab && READ_ONCE(net->ipv4.sysctl_tcp_sack)) {
 					opt_rx->sack_ok = TCP_SACK_SEEN;
 					tcp_sack_reset(opt_rx);
 				}
@@ -4274,9 +4375,26 @@
 		!after(seq, tp->rcv_nxt + tcp_receive_window(tp));
 }
 
+
+void tcp_done_with_error(struct sock *sk, int err)
+{
+	/* This barrier is coupled with smp_rmb() in tcp_poll() */
+	WRITE_ONCE(sk->sk_err, err);
+	smp_wmb();
+
+	tcp_write_queue_purge(sk);
+	tcp_done(sk);
+
+	if (!sock_flag(sk, SOCK_DEAD))
+		sk_error_report(sk);
+}
+EXPORT_SYMBOL(tcp_done_with_error);
+
 /* When we get a reset we do this. */
 void tcp_reset(struct sock *sk, struct sk_buff *skb)
 {
+	int err;
+
 	trace_tcp_receive_reset(sk);
 
 	/* mptcp can't tell us to ignore reset pkts,
@@ -4288,24 +4406,17 @@
 	/* We want the right error as BSD sees it (and indeed as we do). */
 	switch (sk->sk_state) {
 	case TCP_SYN_SENT:
-		sk->sk_err = ECONNREFUSED;
+		err = ECONNREFUSED;
 		break;
 	case TCP_CLOSE_WAIT:
-		sk->sk_err = EPIPE;
+		err = EPIPE;
 		break;
 	case TCP_CLOSE:
 		return;
 	default:
-		sk->sk_err = ECONNRESET;
+		err = ECONNRESET;
 	}
-	/* This barrier is coupled with smp_rmb() in tcp_poll() */
-	smp_wmb();
-
-	tcp_write_queue_purge(sk);
-	tcp_done(sk);
-
-	if (!sock_flag(sk, SOCK_DEAD))
-		sk_error_report(sk);
+	tcp_done_with_error(sk, err);
 }
 
 /*
@@ -4328,7 +4439,7 @@
 
 	inet_csk_schedule_ack(sk);
 
-	sk->sk_shutdown |= RCV_SHUTDOWN;
+	WRITE_ONCE(sk->sk_shutdown, sk->sk_shutdown | RCV_SHUTDOWN);
 	sock_set_flag(sk, SOCK_DONE);
 
 	switch (sk->sk_state) {
@@ -4408,7 +4519,7 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 
-	if (tcp_is_sack(tp) && sock_net(sk)->ipv4.sysctl_tcp_dsack) {
+	if (tcp_is_sack(tp) && READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_dsack)) {
 		int mib_idx;
 
 		if (before(seq, tp->rcv_nxt))
@@ -4455,7 +4566,7 @@
 		NET_INC_STATS(sock_net(sk), LINUX_MIB_DELAYEDACKLOST);
 		tcp_enter_quickack_mode(sk, TCP_MAX_QUICKACKS);
 
-		if (tcp_is_sack(tp) && sock_net(sk)->ipv4.sysctl_tcp_dsack) {
+		if (tcp_is_sack(tp) && READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_dsack)) {
 			u32 end_seq = TCP_SKB_CB(skb)->end_seq;
 
 			tcp_rcv_spurious_retrans(sk, skb);
@@ -5400,7 +5511,7 @@
 		return false;
 
 	/* If we filled the congestion window, do not expand.  */
-	if (tcp_packets_in_flight(tp) >= tp->snd_cwnd)
+	if (tcp_packets_in_flight(tp) >= tcp_snd_cwnd(tp))
 		return false;
 
 	return true;
@@ -5418,7 +5529,17 @@
 	INDIRECT_CALL_1(sk->sk_write_space, sk_stream_write_space, sk);
 }
 
-static void tcp_check_space(struct sock *sk)
+/* Caller made space either from:
+ * 1) Freeing skbs in rtx queues (after tp->snd_una has advanced)
+ * 2) Sent skbs from output queue (and thus advancing tp->snd_nxt)
+ *
+ * We might be able to generate EPOLLOUT to the application if:
+ * 1) Space consumed in output/rtx queues is below sk->sk_sndbuf/2
+ * 2) notsent amount (tp->write_seq - tp->snd_nxt) became
+ *    small enough that tcp_stream_memory_free() decides it
+ *    is time to generate EPOLLOUT.
+ */
+void tcp_check_space(struct sock *sk)
 {
 	/* pairs with tcp_poll() */
 	smp_mb();
@@ -5468,7 +5589,7 @@
 	}
 
 	if (!tcp_is_sack(tp) ||
-	    tp->compressed_ack >= sock_net(sk)->ipv4.sysctl_tcp_comp_sack_nr)
+	    tp->compressed_ack >= READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_comp_sack_nr))
 		goto send_now;
 
 	if (tp->compressed_ack_rcv_nxt != tp->rcv_nxt) {
@@ -5489,11 +5610,12 @@
 	if (tp->srtt_us && tp->srtt_us < rtt)
 		rtt = tp->srtt_us;
 
-	delay = min_t(unsigned long, sock_net(sk)->ipv4.sysctl_tcp_comp_sack_delay_ns,
+	delay = min_t(unsigned long,
+		      READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_comp_sack_delay_ns),
 		      rtt * (NSEC_PER_USEC >> 3)/20);
 	sock_hold(sk);
 	hrtimer_start_range_ns(&tp->compressed_ack_timer, ns_to_ktime(delay),
-			       sock_net(sk)->ipv4.sysctl_tcp_comp_sack_slack_ns,
+			       READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_comp_sack_slack_ns),
 			       HRTIMER_MODE_REL_PINNED_SOFT);
 }
 
@@ -5521,7 +5643,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	u32 ptr = ntohs(th->urg_ptr);
 
-	if (ptr && !sock_net(sk)->ipv4.sysctl_tcp_stdurg)
+	if (ptr && !READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_stdurg))
 		ptr--;
 	ptr += ntohl(th->seq);
 
@@ -5770,7 +5892,7 @@
 	trace_tcp_probe(sk, skb);
 
 	tcp_mstamp_refresh(tp);
-	if (unlikely(!sk->sk_rx_dst))
+	if (unlikely(!rcu_access_pointer(sk->sk_rx_dst)))
 		inet_csk(sk)->icsk_af_ops->sk_rx_dst_set(sk, skb);
 	/*
 	 *	Header prediction.
@@ -5957,9 +6079,9 @@
 	 * retransmission has occurred.
 	 */
 	if (tp->total_retrans > 1 && tp->undo_marker)
-		tp->snd_cwnd = 1;
+		tcp_snd_cwnd_set(tp, 1);
 	else
-		tp->snd_cwnd = tcp_init_cwnd(tp, __sk_dst_get(sk));
+		tcp_snd_cwnd_set(tp, tcp_init_cwnd(tp, __sk_dst_get(sk)));
 	tp->snd_cwnd_stamp = tcp_jiffies32;
 
 	bpf_skops_established(sk, bpf_op, skb);
@@ -6044,7 +6166,7 @@
 			tp->fastopen_client_fail = TFO_DATA_NOT_ACKED;
 		skb_rbtree_walk_from(data)
 			 tcp_mark_skb_lost(sk, data);
-		tcp_xmit_retransmit_queue(sk);
+		tcp_non_congestion_loss_retransmit(sk);
 		NET_INC_STATS(sock_net(sk),
 				LINUX_MIB_TCPFASTOPENACTIVEFAIL);
 		return true;
@@ -6321,22 +6443,23 @@
 
 static void tcp_rcv_synrecv_state_fastopen(struct sock *sk)
 {
+	struct tcp_sock *tp = tcp_sk(sk);
 	struct request_sock *req;
 
 	/* If we are still handling the SYNACK RTO, see if timestamp ECR allows
 	 * undo. If peer SACKs triggered fast recovery, we can't undo here.
 	 */
-	if (inet_csk(sk)->icsk_ca_state == TCP_CA_Loss)
-		tcp_try_undo_loss(sk, false);
+	if (inet_csk(sk)->icsk_ca_state == TCP_CA_Loss && !tp->packets_out)
+		tcp_try_undo_recovery(sk);
 
 	/* Reset rtx states to prevent spurious retransmits_timed_out() */
-	tcp_sk(sk)->retrans_stamp = 0;
+	tp->retrans_stamp = 0;
 	inet_csk(sk)->icsk_retransmits = 0;
 
 	/* Once we leave TCP_SYN_RECV or TCP_FIN_WAIT_1,
 	 * we no longer need req so release it.
 	 */
-	req = rcu_dereference_protected(tcp_sk(sk)->fastopen_rsk,
+	req = rcu_dereference_protected(tp->fastopen_rsk,
 					lockdep_sock_is_held(sk));
 	reqsk_fastopen_remove(sk, req, false);
 
@@ -6483,6 +6606,8 @@
 
 		tcp_initialize_rcv_mss(sk);
 		tcp_fast_path_on(tp);
+		if (sk->sk_shutdown & SEND_SHUTDOWN)
+			tcp_shutdown(sk, SEND_SHUTDOWN);
 		break;
 
 	case TCP_FIN_WAIT1: {
@@ -6495,7 +6620,7 @@
 			break;
 
 		tcp_set_state(sk, TCP_FIN_WAIT2);
-		sk->sk_shutdown |= SEND_SHUTDOWN;
+		WRITE_ONCE(sk->sk_shutdown, sk->sk_shutdown | SEND_SHUTDOWN);
 
 		sk_dst_confirm(sk);
 
@@ -6653,7 +6778,7 @@
 
 	ect = !INET_ECN_is_not_ect(TCP_SKB_CB(skb)->ip_dsfield);
 	ecn_ok_dst = dst_feature(dst, DST_FEATURE_ECN_MASK);
-	ecn_ok = net->ipv4.sysctl_tcp_ecn || ecn_ok_dst;
+	ecn_ok = READ_ONCE(net->ipv4.sysctl_tcp_ecn) || ecn_ok_dst;
 
 	if (((!ect || th->res1) && ecn_ok) || tcp_ca_needs_ecn(listen_sk) ||
 	    (ecn_ok_dst & DST_FEATURE_ECN_CA) ||
@@ -6706,6 +6831,7 @@
 		ireq->ireq_state = TCP_NEW_SYN_RECV;
 		write_pnet(&ireq->ireq_net, sock_net(sk_listener));
 		ireq->ireq_family = sk_listener->sk_family;
+		req->timeout = TCP_TIMEOUT_INIT;
 	}
 
 	return req;
@@ -6719,11 +6845,14 @@
 {
 	struct request_sock_queue *queue = &inet_csk(sk)->icsk_accept_queue;
 	const char *msg = "Dropping request";
-	bool want_cookie = false;
 	struct net *net = sock_net(sk);
+	bool want_cookie = false;
+	u8 syncookies;
+
+	syncookies = READ_ONCE(net->ipv4.sysctl_tcp_syncookies);
 
 #ifdef CONFIG_SYN_COOKIES
-	if (net->ipv4.sysctl_tcp_syncookies) {
+	if (syncookies) {
 		msg = "Sending cookies";
 		want_cookie = true;
 		__NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPREQQFULLDOCOOKIES);
@@ -6731,8 +6860,7 @@
 #endif
 		__NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPREQQFULLDROP);
 
-	if (!queue->synflood_warned &&
-	    net->ipv4.sysctl_tcp_syncookies != 2 &&
+	if (!queue->synflood_warned && syncookies != 2 &&
 	    xchg(&queue->synflood_warned, 1) == 0)
 		net_info_ratelimited("%s: Possible SYN flooding on port %d. %s.  Check SNMP counters.\n",
 				     proto, sk->sk_num, msg);
@@ -6781,7 +6909,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	u16 mss;
 
-	if (sock_net(sk)->ipv4.sysctl_tcp_syncookies != 2 &&
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_syncookies) != 2 &&
 	    !inet_csk_reqsk_queue_is_full(sk))
 		return 0;
 
@@ -6815,13 +6943,15 @@
 	bool want_cookie = false;
 	struct dst_entry *dst;
 	struct flowi fl;
+	u8 syncookies;
+
+	syncookies = READ_ONCE(net->ipv4.sysctl_tcp_syncookies);
 
 	/* TW buckets are converted to open requests without
 	 * limitations, they conserve resources and peer is
 	 * evidently real one.
 	 */
-	if ((net->ipv4.sysctl_tcp_syncookies == 2 ||
-	     inet_csk_reqsk_queue_is_full(sk)) && !isn) {
+	if ((syncookies == 2 || inet_csk_reqsk_queue_is_full(sk)) && !isn) {
 		want_cookie = tcp_syn_flood_action(sk, rsk_ops->slab_name);
 		if (!want_cookie)
 			goto drop;
@@ -6870,10 +7000,12 @@
 		tcp_rsk(req)->ts_off = af_ops->init_ts_off(net, skb);
 
 	if (!want_cookie && !isn) {
+		int max_syn_backlog = READ_ONCE(net->ipv4.sysctl_max_syn_backlog);
+
 		/* Kill the following clause, if you dislike this way. */
-		if (!net->ipv4.sysctl_tcp_syncookies &&
-		    (net->ipv4.sysctl_max_syn_backlog - inet_csk_reqsk_queue_len(sk) <
-		     (net->ipv4.sysctl_max_syn_backlog >> 2)) &&
+		if (!syncookies &&
+		    (max_syn_backlog - inet_csk_reqsk_queue_len(sk) <
+		     (max_syn_backlog >> 2)) &&
 		    !tcp_peer_is_proven(req, dst)) {
 			/* Without syncookies last quarter of
 			 * backlog is filled with destinations,
@@ -6922,9 +7054,16 @@
 		sock_put(fastopen_sk);
 	} else {
 		tcp_rsk(req)->tfo_listener = false;
-		if (!want_cookie)
-			inet_csk_reqsk_queue_hash_add(sk, req,
-				tcp_timeout_init((struct sock *)req));
+		if (!want_cookie) {
+			req->timeout = tcp_timeout_init((struct sock *)req);
+			if (unlikely(!inet_csk_reqsk_queue_hash_add(sk, req,
+								    req->timeout))) {
+				reqsk_free(req);
+				dst_release(dst);
+				return 0;
+			}
+
+		}
 		af_ops->send_synack(sk, dst, &fl, req, &foc,
 				    !want_cookie ? TCP_SYNACK_NORMAL :
 						   TCP_SYNACK_COOKIE,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_ipv4.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_ipv4.c
@@ -91,6 +91,8 @@
 struct inet_hashinfo tcp_hashinfo;
 EXPORT_SYMBOL(tcp_hashinfo);
 
+static DEFINE_PER_CPU(struct sock *, ipv4_tcp_sk);
+
 static u32 tcp_v4_init_seq(const struct sk_buff *skb)
 {
 	return secure_tcp_seq(ip_hdr(skb)->daddr,
@@ -106,10 +108,13 @@
 
 int tcp_twsk_unique(struct sock *sk, struct sock *sktw, void *twp)
 {
+	int reuse = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_tw_reuse);
 	const struct inet_timewait_sock *tw = inet_twsk(sktw);
 	const struct tcp_timewait_sock *tcptw = tcp_twsk(sktw);
 	struct tcp_sock *tp = tcp_sk(sk);
-	int reuse = sock_net(sk)->ipv4.sysctl_tcp_tw_reuse;
+
+	if (tw->tw_substate == TCP_FIN_WAIT2)
+		reuse = 0;
 
 	if (reuse == 2) {
 		/* Still does not detect *everything* that goes through
@@ -151,6 +156,12 @@
 	if (tcptw->tw_ts_recent_stamp &&
 	    (!twp || (reuse && time_after32(ktime_get_seconds(),
 					    tcptw->tw_ts_recent_stamp)))) {
+		/* inet_twsk_hashdance() sets sk_refcnt after putting twsk
+		 * and releasing the bucket lock.
+		 */
+		if (unlikely(!refcount_inc_not_zero(&sktw->sk_refcnt)))
+			return 0;
+
 		/* In case of repair and re-using TIME-WAIT sockets we still
 		 * want to be sure that it is safe as above but honor the
 		 * sequence numbers and time stamps set as part of the repair
@@ -171,7 +182,7 @@
 			tp->rx_opt.ts_recent	   = tcptw->tw_ts_recent;
 			tp->rx_opt.ts_recent_stamp = tcptw->tw_ts_recent_stamp;
 		}
-		sock_hold(sktw);
+
 		return 1;
 	}
 
@@ -322,6 +333,8 @@
 	 * if necessary.
 	 */
 	tcp_set_state(sk, TCP_CLOSE);
+	if (!(sk->sk_userlocks & SOCK_BINDADDR_LOCK))
+		inet_reset_saddr(sk);
 	ip_rt_put(rt);
 	sk->sk_route_caps = 0;
 	inet->inet_dport = 0;
@@ -351,7 +364,7 @@
 	 * for the case, if this connection will not able to recover.
 	 */
 	if (mtu < dst_mtu(dst) && ip_dont_fragment(sk, dst))
-		sk->sk_err_soft = EMSGSIZE;
+		WRITE_ONCE(sk->sk_err_soft, EMSGSIZE);
 
 	mtu = dst_mtu(dst);
 
@@ -582,15 +595,10 @@
 
 		ip_icmp_error(sk, skb, err, th->dest, info, (u8 *)th);
 
-		if (!sock_owned_by_user(sk)) {
-			sk->sk_err = err;
-
-			sk_error_report(sk);
-
-			tcp_done(sk);
-		} else {
-			sk->sk_err_soft = err;
-		}
+		if (!sock_owned_by_user(sk))
+			tcp_done_with_error(sk, err);
+		else
+			WRITE_ONCE(sk->sk_err_soft, err);
 		goto out;
 	}
 
@@ -612,10 +620,10 @@
 
 	inet = inet_sk(sk);
 	if (!sock_owned_by_user(sk) && inet->recverr) {
-		sk->sk_err = err;
+		WRITE_ONCE(sk->sk_err, err);
 		sk_error_report(sk);
 	} else	{ /* Only an error on timeout */
-		sk->sk_err_soft = err;
+		WRITE_ONCE(sk->sk_err_soft, err);
 	}
 
 out:
@@ -807,13 +815,18 @@
 	arg.tos = ip_hdr(skb)->tos;
 	arg.uid = sock_net_uid(net, sk && sk_fullsock(sk) ? sk : NULL);
 	local_bh_disable();
-	ctl_sk = this_cpu_read(*net->ipv4.tcp_sk);
+	ctl_sk = this_cpu_read(ipv4_tcp_sk);
+	sock_net_set(ctl_sk, net);
 	if (sk) {
 		ctl_sk->sk_mark = (sk->sk_state == TCP_TIME_WAIT) ?
 				   inet_twsk(sk)->tw_mark : sk->sk_mark;
 		ctl_sk->sk_priority = (sk->sk_state == TCP_TIME_WAIT) ?
 				   inet_twsk(sk)->tw_priority : sk->sk_priority;
 		transmit_time = tcp_transmit_time(sk);
+		xfrm_sk_clone_policy(ctl_sk, sk);
+	} else {
+		ctl_sk->sk_mark = 0;
+		ctl_sk->sk_priority = 0;
 	}
 	ip_send_unicast_reply(ctl_sk,
 			      skb, &TCP_SKB_CB(skb)->header.h4.opt,
@@ -821,7 +834,8 @@
 			      &arg, arg.iov[0].iov_len,
 			      transmit_time);
 
-	ctl_sk->sk_mark = 0;
+	xfrm_sk_free_policy(ctl_sk);
+	sock_net_set(ctl_sk, &init_net);
 	__TCP_INC_STATS(net, TCP_MIB_OUTSEGS);
 	__TCP_INC_STATS(net, TCP_MIB_OUTRSTS);
 	local_bh_enable();
@@ -905,7 +919,8 @@
 	arg.tos = tos;
 	arg.uid = sock_net_uid(net, sk_fullsock(sk) ? sk : NULL);
 	local_bh_disable();
-	ctl_sk = this_cpu_read(*net->ipv4.tcp_sk);
+	ctl_sk = this_cpu_read(ipv4_tcp_sk);
+	sock_net_set(ctl_sk, net);
 	ctl_sk->sk_mark = (sk->sk_state == TCP_TIME_WAIT) ?
 			   inet_twsk(sk)->tw_mark : sk->sk_mark;
 	ctl_sk->sk_priority = (sk->sk_state == TCP_TIME_WAIT) ?
@@ -917,7 +932,7 @@
 			      &arg, arg.iov[0].iov_len,
 			      transmit_time);
 
-	ctl_sk->sk_mark = 0;
+	sock_net_set(ctl_sk, &init_net);
 	__TCP_INC_STATS(net, TCP_MIB_OUTSEGS);
 	local_bh_enable();
 }
@@ -964,7 +979,7 @@
 			tcp_rsk(req)->rcv_nxt,
 			req->rsk_rcv_wnd >> inet_rsk(req)->rcv_wscale,
 			tcp_time_stamp_raw() + tcp_rsk(req)->ts_off,
-			req->ts_recent,
+			READ_ONCE(req->ts_recent),
 			0,
 			tcp_md5_do_lookup(sk, l3index, addr, AF_INET),
 			inet_rsk(req)->no_srccheck ? IP_REPLY_ARG_NOSRCCHECK : 0,
@@ -998,7 +1013,7 @@
 	if (skb) {
 		__tcp_v4_send_check(skb, ireq->ir_loc_addr, ireq->ir_rmt_addr);
 
-		tos = sock_net(sk)->ipv4.sysctl_tcp_reflect_tos ?
+		tos = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_reflect_tos) ?
 				(tcp_rsk(req)->syn_tos & ~INET_ECN_MASK) |
 				(inet_sk(sk)->tos & INET_ECN_MASK) :
 				inet_sk(sk)->tos;
@@ -1584,7 +1599,7 @@
 	/* Set ToS of the new socket based upon the value of incoming SYN.
 	 * ECT bits are set later in tcp_init_transfer().
 	 */
-	if (sock_net(sk)->ipv4.sysctl_tcp_reflect_tos)
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_reflect_tos))
 		newinet->tos = tcp_rsk(req)->syn_tos & ~INET_ECN_MASK;
 
 	if (!dst) {
@@ -1698,16 +1713,19 @@
 	struct sock *rsk;
 
 	if (sk->sk_state == TCP_ESTABLISHED) { /* Fast path */
-		struct dst_entry *dst = sk->sk_rx_dst;
+		struct dst_entry *dst;
+
+		dst = rcu_dereference_protected(sk->sk_rx_dst,
+						lockdep_sock_is_held(sk));
 
 		sock_rps_save_rxhash(sk, skb);
 		sk_mark_napi_id(sk, skb);
 		if (dst) {
-			if (inet_sk(sk)->rx_dst_ifindex != skb->skb_iif ||
+			if (sk->sk_rx_dst_ifindex != skb->skb_iif ||
 			    !INDIRECT_CALL_1(dst->ops->check, ipv4_dst_check,
 					     dst, 0)) {
+				RCU_INIT_POINTER(sk->sk_rx_dst, NULL);
 				dst_release(dst);
-				sk->sk_rx_dst = NULL;
 			}
 		}
 		tcp_rcv_established(sk, skb);
@@ -1783,12 +1801,12 @@
 		skb->sk = sk;
 		skb->destructor = sock_edemux;
 		if (sk_fullsock(sk)) {
-			struct dst_entry *dst = READ_ONCE(sk->sk_rx_dst);
+			struct dst_entry *dst = rcu_dereference(sk->sk_rx_dst);
 
 			if (dst)
 				dst = dst_check(dst, 0);
 			if (dst &&
-			    inet_sk(sk)->rx_dst_ifindex == skb->skb_iif)
+			    sk->sk_rx_dst_ifindex == skb->skb_iif)
 				skb_dst_set_noref(skb, dst);
 		}
 	}
@@ -1797,7 +1815,6 @@
 
 bool tcp_add_backlog(struct sock *sk, struct sk_buff *skb)
 {
-	u32 limit = READ_ONCE(sk->sk_rcvbuf) + READ_ONCE(sk->sk_sndbuf);
 	u32 tail_gso_size, tail_gso_segs;
 	struct skb_shared_info *shinfo;
 	const struct tcphdr *th;
@@ -1807,6 +1824,7 @@
 	bool fragstolen;
 	u32 gso_segs;
 	u32 gso_size;
+	u64 limit;
 	int delta;
 
 	/* In case all data was pulled from skb frags (in __pskb_pull_tail()),
@@ -1850,6 +1868,7 @@
 #ifdef CONFIG_TLS_DEVICE
 	    tail->decrypted != skb->decrypted ||
 #endif
+	    !mptcp_skb_can_collapse(tail, skb) ||
 	    thtail->doff != th->doff ||
 	    memcmp(thtail + 1, th + 1, hdrlen - sizeof(*th)))
 		goto no_coalesce;
@@ -1902,11 +1921,21 @@
 	__skb_push(skb, hdrlen);
 
 no_coalesce:
+	/* sk->sk_backlog.len is reset only at the end of __release_sock().
+	 * Both sk->sk_backlog.len and sk->sk_rmem_alloc could reach
+	 * sk_rcvbuf in normal conditions.
+	 */
+	limit = ((u64)READ_ONCE(sk->sk_rcvbuf)) << 1;
+
+	limit += ((u32)READ_ONCE(sk->sk_sndbuf)) >> 1;
+
 	/* Only socket owner can try to collapse/prune rx queues
 	 * to reduce memory overhead, so add a little headroom here.
 	 * Few sockets backlog are possibly concurrently non empty.
 	 */
-	limit += 64*1024;
+	limit += 64 * 1024;
+
+	limit = min_t(u64, limit, UINT_MAX);
 
 	if (unlikely(sk_add_backlog(sk, skb, limit))) {
 		bh_unlock_sock(sk);
@@ -1967,8 +1996,10 @@
 	const struct tcphdr *th;
 	bool refcounted;
 	struct sock *sk;
+	int drop_reason;
 	int ret;
 
+	drop_reason = SKB_DROP_REASON_NOT_SPECIFIED;
 	if (skb->pkt_type != PACKET_HOST)
 		goto discard_it;
 
@@ -1980,8 +2011,10 @@
 
 	th = (const struct tcphdr *)skb->data;
 
-	if (unlikely(th->doff < sizeof(struct tcphdr) / 4))
+	if (unlikely(th->doff < sizeof(struct tcphdr) / 4)) {
+		drop_reason = SKB_DROP_REASON_PKT_TOO_SMALL;
 		goto bad_packet;
+	}
 	if (!pskb_may_pull(skb, th->doff * 4))
 		goto discard_it;
 
@@ -2011,7 +2044,8 @@
 		struct sock *nsk;
 
 		sk = req->rsk_listener;
-		if (unlikely(tcp_v4_inbound_md5_hash(sk, skb, dif, sdif))) {
+		if (unlikely(!xfrm4_policy_check(sk, XFRM_POLICY_IN, skb) ||
+			     tcp_v4_inbound_md5_hash(sk, skb, dif, sdif))) {
 			sk_drops_add(sk, skb);
 			reqsk_put(req);
 			goto discard_it;
@@ -2058,6 +2092,7 @@
 			}
 			goto discard_and_relse;
 		}
+		nf_reset_ct(skb);
 		if (nsk == sk) {
 			reqsk_put(req);
 			tcp_v4_restore_cb(skb);
@@ -2082,8 +2117,10 @@
 
 	nf_reset_ct(skb);
 
-	if (tcp_filter(sk, skb))
+	if (tcp_filter(sk, skb)) {
+		drop_reason = SKB_DROP_REASON_SOCKET_FILTER;
 		goto discard_and_relse;
+	}
 	th = (const struct tcphdr *)skb->data;
 	iph = ip_hdr(skb);
 	tcp_v4_fill_cb(skb, iph, th);
@@ -2120,6 +2157,7 @@
 	return ret;
 
 no_tcp_socket:
+	drop_reason = SKB_DROP_REASON_NO_SOCKET;
 	if (!xfrm4_policy_check(NULL, XFRM_POLICY_IN, skb))
 		goto discard_it;
 
@@ -2127,6 +2165,7 @@
 
 	if (tcp_checksum_complete(skb)) {
 csum_error:
+		drop_reason = SKB_DROP_REASON_TCP_CSUM;
 		trace_tcp_bad_csum(skb);
 		__TCP_INC_STATS(net, TCP_MIB_CSUMERRORS);
 bad_packet:
@@ -2137,7 +2176,7 @@
 
 discard_it:
 	/* Discard frame. */
-	kfree_skb(skb);
+	kfree_skb_reason(skb, drop_reason);
 	return 0;
 
 discard_and_relse:
@@ -2200,8 +2239,8 @@
 	struct dst_entry *dst = skb_dst(skb);
 
 	if (dst && dst_hold_safe(dst)) {
-		sk->sk_rx_dst = dst;
-		inet_sk(sk)->rx_dst_ifindex = skb->skb_iif;
+		rcu_assign_pointer(sk->sk_rx_dst, dst);
+		sk->sk_rx_dst_ifindex = skb->skb_iif;
 	}
 }
 EXPORT_SYMBOL(inet_sk_rx_dst_set);
@@ -2317,16 +2356,15 @@
 	st->offset = 0;
 	for (; st->bucket <= tcp_hashinfo.lhash2_mask; st->bucket++) {
 		struct inet_listen_hashbucket *ilb2;
-		struct inet_connection_sock *icsk;
+		struct hlist_nulls_node *node;
 		struct sock *sk;
 
 		ilb2 = &tcp_hashinfo.lhash2[st->bucket];
-		if (hlist_empty(&ilb2->head))
+		if (hlist_nulls_empty(&ilb2->nulls_head))
 			continue;
 
 		spin_lock(&ilb2->lock);
-		inet_lhash2_for_each_icsk(icsk, &ilb2->head) {
-			sk = (struct sock *)icsk;
+		sk_nulls_for_each(sk, node, &ilb2->nulls_head) {
 			if (seq_sk_match(seq, sk))
 				return sk;
 		}
@@ -2345,15 +2383,14 @@
 {
 	struct tcp_iter_state *st = seq->private;
 	struct inet_listen_hashbucket *ilb2;
-	struct inet_connection_sock *icsk;
+	struct hlist_nulls_node *node;
 	struct sock *sk = cur;
 
 	++st->num;
 	++st->offset;
 
-	icsk = inet_csk(sk);
-	inet_lhash2_for_each_icsk_continue(icsk) {
-		sk = (struct sock *)icsk;
+	sk = sk_nulls_next(sk);
+	sk_nulls_for_each_from(sk, node) {
 		if (seq_sk_match(seq, sk))
 			return sk;
 	}
@@ -2653,7 +2690,7 @@
 		jiffies_to_clock_t(icsk->icsk_rto),
 		jiffies_to_clock_t(icsk->icsk_ack.ato),
 		(icsk->icsk_ack.quick << 1) | inet_csk_in_pingpong_mode(sk),
-		tp->snd_cwnd,
+		tcp_snd_cwnd(tp),
 		state == TCP_LISTEN ?
 		    fastopenq->max_qlen :
 		    (tcp_in_initial_slowstart(tp) ? -1 : tp->snd_ssthresh));
@@ -2736,7 +2773,7 @@
 static void bpf_iter_tcp_put_batch(struct bpf_tcp_iter_state *iter)
 {
 	while (iter->cur_sk < iter->end_sk)
-		sock_put(iter->batch[iter->cur_sk++]);
+		sock_gen_put(iter->batch[iter->cur_sk++]);
 }
 
 static int bpf_iter_tcp_realloc_batch(struct bpf_tcp_iter_state *iter,
@@ -2762,16 +2799,15 @@
 {
 	struct bpf_tcp_iter_state *iter = seq->private;
 	struct tcp_iter_state *st = &iter->state;
-	struct inet_connection_sock *icsk;
+	struct hlist_nulls_node *node;
 	unsigned int expected = 1;
 	struct sock *sk;
 
 	sock_hold(start_sk);
 	iter->batch[iter->end_sk++] = start_sk;
 
-	icsk = inet_csk(start_sk);
-	inet_lhash2_for_each_icsk_continue(icsk) {
-		sk = (struct sock *)icsk;
+	sk = sk_nulls_next(start_sk);
+	sk_nulls_for_each_from(sk, node) {
 		if (seq_sk_match(seq, sk)) {
 			if (iter->end_sk < iter->max_sk) {
 				sock_hold(sk);
@@ -2895,7 +2931,7 @@
 		 * st->bucket.  See tcp_seek_last_pos().
 		 */
 		st->offset++;
-		sock_put(iter->batch[iter->cur_sk++]);
+		sock_gen_put(iter->batch[iter->cur_sk++]);
 	}
 
 	if (iter->cur_sk < iter->end_sk)
@@ -3098,41 +3134,14 @@
 
 static void __net_exit tcp_sk_exit(struct net *net)
 {
-	int cpu;
-
 	if (net->ipv4.tcp_congestion_control)
 		bpf_module_put(net->ipv4.tcp_congestion_control,
 			       net->ipv4.tcp_congestion_control->owner);
-
-	for_each_possible_cpu(cpu)
-		inet_ctl_sock_destroy(*per_cpu_ptr(net->ipv4.tcp_sk, cpu));
-	free_percpu(net->ipv4.tcp_sk);
 }
 
 static int __net_init tcp_sk_init(struct net *net)
 {
-	int res, cpu, cnt;
-
-	net->ipv4.tcp_sk = alloc_percpu(struct sock *);
-	if (!net->ipv4.tcp_sk)
-		return -ENOMEM;
-
-	for_each_possible_cpu(cpu) {
-		struct sock *sk;
-
-		res = inet_ctl_sock_create(&sk, PF_INET, SOCK_RAW,
-					   IPPROTO_TCP, net);
-		if (res)
-			goto fail;
-		sock_set_flag(sk, SOCK_USE_WRITE_QUEUE);
-
-		/* Please enforce IP_DF and IPID==0 for RST and
-		 * ACK sent in SYN-RECV and TIME-WAIT state.
-		 */
-		inet_sk(sk)->pmtudisc = IP_PMTUDISC_DO;
-
-		*per_cpu_ptr(net->ipv4.tcp_sk, cpu) = sk;
-	}
+	int cnt;
 
 	net->ipv4.sysctl_tcp_ecn = 2;
 	net->ipv4.sysctl_tcp_ecn_fallback = 1;
@@ -3216,10 +3225,6 @@
 		net->ipv4.tcp_congestion_control = &tcp_reno;
 
 	return 0;
-fail:
-	tcp_sk_exit(net);
-
-	return res;
 }
 
 static void __net_exit tcp_sk_exit_batch(struct list_head *net_exit_list)
@@ -3313,6 +3318,24 @@
 
 void __init tcp_v4_init(void)
 {
+	int cpu, res;
+
+	for_each_possible_cpu(cpu) {
+		struct sock *sk;
+
+		res = inet_ctl_sock_create(&sk, PF_INET, SOCK_RAW,
+					   IPPROTO_TCP, &init_net);
+		if (res)
+			panic("Failed to create the TCP control socket.\n");
+		sock_set_flag(sk, SOCK_USE_WRITE_QUEUE);
+
+		/* Please enforce IP_DF and IPID==0 for RST and
+		 * ACK sent in SYN-RECV and TIME-WAIT state.
+		 */
+		inet_sk(sk)->pmtudisc = IP_PMTUDISC_DO;
+
+		per_cpu(ipv4_tcp_sk, cpu) = sk;
+	}
 	if (register_pernet_subsys(&tcp_sk_ops))
 		panic("Failed to create the TCP control socket.\n");
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_lp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_lp.c
@@ -297,7 +297,7 @@
 		lp->flag &= ~LP_WITHIN_THR;
 
 	pr_debug("TCP-LP: %05o|%5u|%5u|%15u|%15u|%15u\n", lp->flag,
-		 tp->snd_cwnd, lp->remote_hz, lp->owd_min, lp->owd_max,
+		 tcp_snd_cwnd(tp), lp->remote_hz, lp->owd_min, lp->owd_max,
 		 lp->sowd >> 3);
 
 	if (lp->flag & LP_WITHIN_THR)
@@ -313,12 +313,12 @@
 	/* happened within inference
 	 * drop snd_cwnd into 1 */
 	if (lp->flag & LP_WITHIN_INF)
-		tp->snd_cwnd = 1U;
+		tcp_snd_cwnd_set(tp, 1U);
 
 	/* happened after inference
 	 * cut snd_cwnd into half */
 	else
-		tp->snd_cwnd = max(tp->snd_cwnd >> 1U, 1U);
+		tcp_snd_cwnd_set(tp, max(tcp_snd_cwnd(tp) >> 1U, 1U));
 
 	/* record this drop time */
 	lp->last_drop = now;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_metrics.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_metrics.c
@@ -40,7 +40,7 @@
 
 struct tcp_metrics_block {
 	struct tcp_metrics_block __rcu	*tcpm_next;
-	possible_net_t			tcpm_net;
+	struct net			*tcpm_net;
 	struct inetpeer_addr		tcpm_saddr;
 	struct inetpeer_addr		tcpm_daddr;
 	unsigned long			tcpm_stamp;
@@ -51,34 +51,38 @@
 	struct rcu_head			rcu_head;
 };
 
-static inline struct net *tm_net(struct tcp_metrics_block *tm)
+static inline struct net *tm_net(const struct tcp_metrics_block *tm)
 {
-	return read_pnet(&tm->tcpm_net);
+	/* Paired with the WRITE_ONCE() in tcpm_new() */
+	return READ_ONCE(tm->tcpm_net);
 }
 
 static bool tcp_metric_locked(struct tcp_metrics_block *tm,
 			      enum tcp_metric_index idx)
 {
-	return tm->tcpm_lock & (1 << idx);
+	/* Paired with WRITE_ONCE() in tcpm_suck_dst() */
+	return READ_ONCE(tm->tcpm_lock) & (1 << idx);
 }
 
-static u32 tcp_metric_get(struct tcp_metrics_block *tm,
+static u32 tcp_metric_get(const struct tcp_metrics_block *tm,
 			  enum tcp_metric_index idx)
 {
-	return tm->tcpm_vals[idx];
+	/* Paired with WRITE_ONCE() in tcp_metric_set() */
+	return READ_ONCE(tm->tcpm_vals[idx]);
 }
 
 static void tcp_metric_set(struct tcp_metrics_block *tm,
 			   enum tcp_metric_index idx,
 			   u32 val)
 {
-	tm->tcpm_vals[idx] = val;
+	/* Paired with READ_ONCE() in tcp_metric_get() */
+	WRITE_ONCE(tm->tcpm_vals[idx], val);
 }
 
 static bool addr_same(const struct inetpeer_addr *a,
 		      const struct inetpeer_addr *b)
 {
-	return inetpeer_addr_cmp(a, b) == 0;
+	return (a->family == b->family) && !inetpeer_addr_cmp(a, b);
 }
 
 struct tcpm_hash_bucket {
@@ -89,6 +93,7 @@
 static unsigned int		tcp_metrics_hash_log __read_mostly;
 
 static DEFINE_SPINLOCK(tcp_metrics_lock);
+static DEFINE_SEQLOCK(fastopen_seqlock);
 
 static void tcpm_suck_dst(struct tcp_metrics_block *tm,
 			  const struct dst_entry *dst,
@@ -97,7 +102,7 @@
 	u32 msval;
 	u32 val;
 
-	tm->tcpm_stamp = jiffies;
+	WRITE_ONCE(tm->tcpm_stamp, jiffies);
 
 	val = 0;
 	if (dst_metric_locked(dst, RTAX_RTT))
@@ -110,30 +115,42 @@
 		val |= 1 << TCP_METRIC_CWND;
 	if (dst_metric_locked(dst, RTAX_REORDERING))
 		val |= 1 << TCP_METRIC_REORDERING;
-	tm->tcpm_lock = val;
+	/* Paired with READ_ONCE() in tcp_metric_locked() */
+	WRITE_ONCE(tm->tcpm_lock, val);
 
 	msval = dst_metric_raw(dst, RTAX_RTT);
-	tm->tcpm_vals[TCP_METRIC_RTT] = msval * USEC_PER_MSEC;
+	tcp_metric_set(tm, TCP_METRIC_RTT, msval * USEC_PER_MSEC);
 
 	msval = dst_metric_raw(dst, RTAX_RTTVAR);
-	tm->tcpm_vals[TCP_METRIC_RTTVAR] = msval * USEC_PER_MSEC;
-	tm->tcpm_vals[TCP_METRIC_SSTHRESH] = dst_metric_raw(dst, RTAX_SSTHRESH);
-	tm->tcpm_vals[TCP_METRIC_CWND] = dst_metric_raw(dst, RTAX_CWND);
-	tm->tcpm_vals[TCP_METRIC_REORDERING] = dst_metric_raw(dst, RTAX_REORDERING);
+	tcp_metric_set(tm, TCP_METRIC_RTTVAR, msval * USEC_PER_MSEC);
+	tcp_metric_set(tm, TCP_METRIC_SSTHRESH,
+		       dst_metric_raw(dst, RTAX_SSTHRESH));
+	tcp_metric_set(tm, TCP_METRIC_CWND,
+		       dst_metric_raw(dst, RTAX_CWND));
+	tcp_metric_set(tm, TCP_METRIC_REORDERING,
+		       dst_metric_raw(dst, RTAX_REORDERING));
 	if (fastopen_clear) {
+		write_seqlock(&fastopen_seqlock);
 		tm->tcpm_fastopen.mss = 0;
 		tm->tcpm_fastopen.syn_loss = 0;
 		tm->tcpm_fastopen.try_exp = 0;
 		tm->tcpm_fastopen.cookie.exp = false;
 		tm->tcpm_fastopen.cookie.len = 0;
+		write_sequnlock(&fastopen_seqlock);
 	}
 }
 
 #define TCP_METRICS_TIMEOUT		(60 * 60 * HZ)
 
-static void tcpm_check_stamp(struct tcp_metrics_block *tm, struct dst_entry *dst)
+static void tcpm_check_stamp(struct tcp_metrics_block *tm,
+			     const struct dst_entry *dst)
 {
-	if (tm && unlikely(time_after(jiffies, tm->tcpm_stamp + TCP_METRICS_TIMEOUT)))
+	unsigned long limit;
+
+	if (!tm)
+		return;
+	limit = READ_ONCE(tm->tcpm_stamp) + TCP_METRICS_TIMEOUT;
+	if (unlikely(time_after(jiffies, limit)))
 		tcpm_suck_dst(tm, dst, false);
 }
 
@@ -174,20 +191,23 @@
 		oldest = deref_locked(tcp_metrics_hash[hash].chain);
 		for (tm = deref_locked(oldest->tcpm_next); tm;
 		     tm = deref_locked(tm->tcpm_next)) {
-			if (time_before(tm->tcpm_stamp, oldest->tcpm_stamp))
+			if (time_before(READ_ONCE(tm->tcpm_stamp),
+					READ_ONCE(oldest->tcpm_stamp)))
 				oldest = tm;
 		}
 		tm = oldest;
 	} else {
-		tm = kmalloc(sizeof(*tm), GFP_ATOMIC);
+		tm = kzalloc(sizeof(*tm), GFP_ATOMIC);
 		if (!tm)
 			goto out_unlock;
 	}
-	write_pnet(&tm->tcpm_net, net);
+	/* Paired with the READ_ONCE() in tm_net() */
+	WRITE_ONCE(tm->tcpm_net, net);
+
 	tm->tcpm_saddr = *saddr;
 	tm->tcpm_daddr = *daddr;
 
-	tcpm_suck_dst(tm, dst, true);
+	tcpm_suck_dst(tm, dst, reclaim);
 
 	if (likely(!reclaim)) {
 		tm->tcpm_next = tcp_metrics_hash[hash].chain;
@@ -329,7 +349,7 @@
 	int m;
 
 	sk_dst_confirm(sk);
-	if (net->ipv4.sysctl_tcp_nometrics_save || !dst)
+	if (READ_ONCE(net->ipv4.sysctl_tcp_nometrics_save) || !dst)
 		return;
 
 	rcu_read_lock();
@@ -385,29 +405,29 @@
 
 	if (tcp_in_initial_slowstart(tp)) {
 		/* Slow start still did not finish. */
-		if (!net->ipv4.sysctl_tcp_no_ssthresh_metrics_save &&
+		if (!READ_ONCE(net->ipv4.sysctl_tcp_no_ssthresh_metrics_save) &&
 		    !tcp_metric_locked(tm, TCP_METRIC_SSTHRESH)) {
 			val = tcp_metric_get(tm, TCP_METRIC_SSTHRESH);
-			if (val && (tp->snd_cwnd >> 1) > val)
+			if (val && (tcp_snd_cwnd(tp) >> 1) > val)
 				tcp_metric_set(tm, TCP_METRIC_SSTHRESH,
-					       tp->snd_cwnd >> 1);
+					       tcp_snd_cwnd(tp) >> 1);
 		}
 		if (!tcp_metric_locked(tm, TCP_METRIC_CWND)) {
 			val = tcp_metric_get(tm, TCP_METRIC_CWND);
-			if (tp->snd_cwnd > val)
+			if (tcp_snd_cwnd(tp) > val)
 				tcp_metric_set(tm, TCP_METRIC_CWND,
-					       tp->snd_cwnd);
+					       tcp_snd_cwnd(tp));
 		}
 	} else if (!tcp_in_slow_start(tp) &&
 		   icsk->icsk_ca_state == TCP_CA_Open) {
 		/* Cong. avoidance phase, cwnd is reliable. */
-		if (!net->ipv4.sysctl_tcp_no_ssthresh_metrics_save &&
+		if (!READ_ONCE(net->ipv4.sysctl_tcp_no_ssthresh_metrics_save) &&
 		    !tcp_metric_locked(tm, TCP_METRIC_SSTHRESH))
 			tcp_metric_set(tm, TCP_METRIC_SSTHRESH,
-				       max(tp->snd_cwnd >> 1, tp->snd_ssthresh));
+				       max(tcp_snd_cwnd(tp) >> 1, tp->snd_ssthresh));
 		if (!tcp_metric_locked(tm, TCP_METRIC_CWND)) {
 			val = tcp_metric_get(tm, TCP_METRIC_CWND);
-			tcp_metric_set(tm, TCP_METRIC_CWND, (val + tp->snd_cwnd) >> 1);
+			tcp_metric_set(tm, TCP_METRIC_CWND, (val + tcp_snd_cwnd(tp)) >> 1);
 		}
 	} else {
 		/* Else slow start did not finish, cwnd is non-sense,
@@ -418,7 +438,7 @@
 			tcp_metric_set(tm, TCP_METRIC_CWND,
 				       (val + tp->snd_ssthresh) >> 1);
 		}
-		if (!net->ipv4.sysctl_tcp_no_ssthresh_metrics_save &&
+		if (!READ_ONCE(net->ipv4.sysctl_tcp_no_ssthresh_metrics_save) &&
 		    !tcp_metric_locked(tm, TCP_METRIC_SSTHRESH)) {
 			val = tcp_metric_get(tm, TCP_METRIC_SSTHRESH);
 			if (val && tp->snd_ssthresh > val)
@@ -428,12 +448,13 @@
 		if (!tcp_metric_locked(tm, TCP_METRIC_REORDERING)) {
 			val = tcp_metric_get(tm, TCP_METRIC_REORDERING);
 			if (val < tp->reordering &&
-			    tp->reordering != net->ipv4.sysctl_tcp_reordering)
+			    tp->reordering !=
+			    READ_ONCE(net->ipv4.sysctl_tcp_reordering))
 				tcp_metric_set(tm, TCP_METRIC_REORDERING,
 					       tp->reordering);
 		}
 	}
-	tm->tcpm_stamp = jiffies;
+	WRITE_ONCE(tm->tcpm_stamp, jiffies);
 out_unlock:
 	rcu_read_unlock();
 }
@@ -449,11 +470,15 @@
 	u32 val, crtt = 0; /* cached RTT scaled by 8 */
 
 	sk_dst_confirm(sk);
+	/* ssthresh may have been reduced unnecessarily during.
+	 * 3WHS. Restore it back to its initial default.
+	 */
+	tp->snd_ssthresh = TCP_INFINITE_SSTHRESH;
 	if (!dst)
 		goto reset;
 
 	rcu_read_lock();
-	tm = tcp_get_metrics(sk, dst, true);
+	tm = tcp_get_metrics(sk, dst, false);
 	if (!tm) {
 		rcu_read_unlock();
 		goto reset;
@@ -462,17 +487,12 @@
 	if (tcp_metric_locked(tm, TCP_METRIC_CWND))
 		tp->snd_cwnd_clamp = tcp_metric_get(tm, TCP_METRIC_CWND);
 
-	val = net->ipv4.sysctl_tcp_no_ssthresh_metrics_save ?
+	val = READ_ONCE(net->ipv4.sysctl_tcp_no_ssthresh_metrics_save) ?
 	      0 : tcp_metric_get(tm, TCP_METRIC_SSTHRESH);
 	if (val) {
 		tp->snd_ssthresh = val;
 		if (tp->snd_ssthresh > tp->snd_cwnd_clamp)
 			tp->snd_ssthresh = tp->snd_cwnd_clamp;
-	} else {
-		/* ssthresh may have been reduced unnecessarily during.
-		 * 3WHS. Restore it back to its initial default.
-		 */
-		tp->snd_ssthresh = TCP_INFINITE_SSTHRESH;
 	}
 	val = tcp_metric_get(tm, TCP_METRIC_REORDERING);
 	if (val && tp->reordering != val)
@@ -538,8 +558,6 @@
 	return ret;
 }
 
-static DEFINE_SEQLOCK(fastopen_seqlock);
-
 void tcp_fastopen_cache_get(struct sock *sk, u16 *mss,
 			    struct tcp_fastopen_cookie *cookie)
 {
@@ -601,6 +619,7 @@
 	[TCP_METRICS_ATTR_ADDR_IPV4]	= { .type = NLA_U32, },
 	[TCP_METRICS_ATTR_ADDR_IPV6]	= { .type = NLA_BINARY,
 					    .len = sizeof(struct in6_addr), },
+	[TCP_METRICS_ATTR_SADDR_IPV4]	= { .type = NLA_U32, },
 	/* Following attributes are not received for GET/DEL,
 	 * we keep them for reference
 	 */
@@ -646,7 +665,7 @@
 	}
 
 	if (nla_put_msecs(msg, TCP_METRICS_ATTR_AGE,
-			  jiffies - tm->tcpm_stamp,
+			  jiffies - READ_ONCE(tm->tcpm_stamp),
 			  TCP_METRICS_ATTR_PAD) < 0)
 		goto nla_put_failure;
 
@@ -657,7 +676,7 @@
 		if (!nest)
 			goto nla_put_failure;
 		for (i = 0; i < TCP_METRIC_MAX_KERNEL + 1; i++) {
-			u32 val = tm->tcpm_vals[i];
+			u32 val = tcp_metric_get(tm, i);
 
 			if (!val)
 				continue;
@@ -889,7 +908,7 @@
 			match = net ? net_eq(tm_net(tm), net) :
 				!refcount_read(&tm_net(tm)->ns.count);
 			if (match) {
-				*pp = tm->tcpm_next;
+				rcu_assign_pointer(*pp, tm->tcpm_next);
 				kfree_rcu(tm, rcu_head);
 			} else {
 				pp = &tm->tcpm_next;
@@ -930,7 +949,7 @@
 		if (addr_same(&tm->tcpm_daddr, &daddr) &&
 		    (!src || addr_same(&tm->tcpm_saddr, &saddr)) &&
 		    net_eq(tm_net(tm), net)) {
-			*pp = tm->tcpm_next;
+			rcu_assign_pointer(*pp, tm->tcpm_next);
 			kfree_rcu(tm, rcu_head);
 			found = true;
 		} else {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_minisocks.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_minisocks.c
@@ -180,7 +180,7 @@
 			 * Oh well... nobody has a sufficient solution to this
 			 * protocol bug yet.
 			 */
-			if (twsk_net(tw)->ipv4.sysctl_tcp_rfc1337 == 0) {
+			if (!READ_ONCE(twsk_net(tw)->ipv4.sysctl_tcp_rfc1337)) {
 kill:
 				inet_twsk_deschedule_put(tw);
 				return TCP_TW_SUCCESS;
@@ -523,7 +523,7 @@
 	newtp->max_window = newtp->snd_wnd;
 
 	if (newtp->rx_opt.tstamp_ok) {
-		newtp->rx_opt.ts_recent = req->ts_recent;
+		newtp->rx_opt.ts_recent = READ_ONCE(req->ts_recent);
 		newtp->rx_opt.ts_recent_stamp = ktime_get_seconds();
 		newtp->tcp_header_len = sizeof(struct tcphdr) + TCPOLEN_TSTAMP_ALIGNED;
 	} else {
@@ -538,7 +538,7 @@
 	newtp->tsoffset = treq->ts_off;
 #ifdef CONFIG_TCP_MD5SIG
 	newtp->md5sig_info = NULL;	/*XXX*/
-	if (newtp->af_specific->md5_lookup(sk, newsk))
+	if (treq->af_specific->req_md5_lookup(sk, req_to_sk(req)))
 		newtp->tcp_header_len += TCPOLEN_MD5SIG_ALIGNED;
 #endif
 	if (skb->len >= TCP_MSS_DEFAULT + newtp->tcp_header_len)
@@ -565,6 +565,9 @@
  * validation and inside tcp_v4_reqsk_send_ack(). Can we do better?
  *
  * We don't need to initialize tmp_opt.sack_ok as we don't use the results
+ *
+ * Note: If @fastopen is true, this can be called from process context.
+ *       Otherwise, this is from BH context.
  */
 
 struct sock *tcp_check_req(struct sock *sk, struct sk_buff *skb,
@@ -583,14 +586,14 @@
 		tcp_parse_options(sock_net(sk), skb, &tmp_opt, 0, NULL);
 
 		if (tmp_opt.saw_tstamp) {
-			tmp_opt.ts_recent = req->ts_recent;
+			tmp_opt.ts_recent = READ_ONCE(req->ts_recent);
 			if (tmp_opt.rcv_tsecr)
 				tmp_opt.rcv_tsecr -= tcp_rsk(req)->ts_off;
 			/* We do not store true stamp, but it is not required,
 			 * it can be estimated (approximately)
 			 * from another data.
 			 */
-			tmp_opt.ts_recent_stamp = ktime_get_seconds() - ((TCP_TIMEOUT_INIT/HZ)<<req->num_timeout);
+			tmp_opt.ts_recent_stamp = ktime_get_seconds() - reqsk_timeout(req, TCP_RTO_MAX) / HZ;
 			paws_reject = tcp_paws_reject(&tmp_opt, th->rst);
 		}
 	}
@@ -629,8 +632,7 @@
 		    !inet_rtx_syn_ack(sk, req)) {
 			unsigned long expires = jiffies;
 
-			expires += min(TCP_TIMEOUT_INIT << req->num_timeout,
-				       TCP_RTO_MAX);
+			expires += reqsk_timeout(req, TCP_RTO_MAX);
 			if (!fastopen)
 				mod_timer_pending(&req->rsk_timer, expires);
 			else
@@ -717,15 +719,12 @@
 					  &tcp_rsk(req)->last_oow_ack_time))
 			req->rsk_ops->send_ack(sk, skb, req);
 		if (paws_reject)
-			__NET_INC_STATS(sock_net(sk), LINUX_MIB_PAWSESTABREJECTED);
+			NET_INC_STATS(sock_net(sk), LINUX_MIB_PAWSESTABREJECTED);
 		return NULL;
 	}
 
 	/* In sequence, PAWS is OK. */
 
-	if (tmp_opt.saw_tstamp && !after(TCP_SKB_CB(skb)->seq, tcp_rsk(req)->rcv_nxt))
-		req->ts_recent = tmp_opt.rcv_tsval;
-
 	if (TCP_SKB_CB(skb)->seq == tcp_rsk(req)->rcv_isn) {
 		/* Truncate SYN, it is out of window starting
 		   at tcp_rsk(req)->rcv_isn + 1. */
@@ -736,7 +735,7 @@
 	 *	   "fourth, check the SYN bit"
 	 */
 	if (flg & (TCP_FLAG_RST|TCP_FLAG_SYN)) {
-		__TCP_INC_STATS(sock_net(sk), TCP_MIB_ATTEMPTFAILS);
+		TCP_INC_STATS(sock_net(sk), TCP_MIB_ATTEMPTFAILS);
 		goto embryonic_reset;
 	}
 
@@ -774,6 +773,10 @@
 	if (!child)
 		goto listen_overflow;
 
+	if (own_req && tmp_opt.saw_tstamp &&
+	    !after(TCP_SKB_CB(skb)->seq, tcp_rsk(req)->rcv_nxt))
+		tcp_sk(child)->rx_opt.ts_recent = tmp_opt.rcv_tsval;
+
 	if (own_req && rsk_drop_req(req)) {
 		reqsk_queue_removed(&inet_csk(req->rsk_listener)->icsk_accept_queue, req);
 		inet_csk_reqsk_queue_drop_and_put(req->rsk_listener, req);
@@ -789,7 +792,7 @@
 	if (sk != req->rsk_listener)
 		__NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPMIGRATEREQFAILURE);
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_abort_on_overflow) {
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_abort_on_overflow)) {
 		inet_rsk(req)->acked = 1;
 		return NULL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_nv.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_nv.c
@@ -198,10 +198,10 @@
 	}
 
 	if (ca->cwnd_growth_factor < 0) {
-		cnt = tp->snd_cwnd << -ca->cwnd_growth_factor;
+		cnt = tcp_snd_cwnd(tp) << -ca->cwnd_growth_factor;
 		tcp_cong_avoid_ai(tp, cnt, acked);
 	} else {
-		cnt = max(4U, tp->snd_cwnd >> ca->cwnd_growth_factor);
+		cnt = max(4U, tcp_snd_cwnd(tp) >> ca->cwnd_growth_factor);
 		tcp_cong_avoid_ai(tp, cnt, acked);
 	}
 }
@@ -210,7 +210,7 @@
 {
 	const struct tcp_sock *tp = tcp_sk(sk);
 
-	return max((tp->snd_cwnd * nv_loss_dec_factor) >> 10, 2U);
+	return max((tcp_snd_cwnd(tp) * nv_loss_dec_factor) >> 10, 2U);
 }
 
 static void tcpnv_state(struct sock *sk, u8 new_state)
@@ -258,7 +258,7 @@
 		return;
 
 	/* Stop cwnd growth if we were in catch up mode */
-	if (ca->nv_catchup && tp->snd_cwnd >= nv_min_cwnd) {
+	if (ca->nv_catchup && tcp_snd_cwnd(tp) >= nv_min_cwnd) {
 		ca->nv_catchup = 0;
 		ca->nv_allow_cwnd_growth = 0;
 	}
@@ -372,7 +372,7 @@
 		 * if cwnd < max_win, grow cwnd
 		 * else leave the same
 		 */
-		if (tp->snd_cwnd > max_win) {
+		if (tcp_snd_cwnd(tp) > max_win) {
 			/* there is congestion, check that it is ok
 			 * to make a CA decision
 			 * 1. We should have at least nv_dec_eval_min_calls
@@ -399,20 +399,20 @@
 			ca->nv_allow_cwnd_growth = 0;
 			tp->snd_ssthresh =
 				(nv_ssthresh_factor * max_win) >> 3;
-			if (tp->snd_cwnd - max_win > 2) {
+			if (tcp_snd_cwnd(tp) - max_win > 2) {
 				/* gap > 2, we do exponential cwnd decrease */
 				int dec;
 
-				dec = max(2U, ((tp->snd_cwnd - max_win) *
+				dec = max(2U, ((tcp_snd_cwnd(tp) - max_win) *
 					       nv_cong_dec_mult) >> 7);
-				tp->snd_cwnd -= dec;
+				tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) - dec);
 			} else if (nv_cong_dec_mult > 0) {
-				tp->snd_cwnd = max_win;
+				tcp_snd_cwnd_set(tp, max_win);
 			}
 			if (ca->cwnd_growth_factor > 0)
 				ca->cwnd_growth_factor = 0;
 			ca->nv_no_cong_cnt = 0;
-		} else if (tp->snd_cwnd <= max_win - nv_pad_buffer) {
+		} else if (tcp_snd_cwnd(tp) <= max_win - nv_pad_buffer) {
 			/* There is no congestion, grow cwnd if allowed*/
 			if (ca->nv_eval_call_cnt < nv_inc_eval_min_calls)
 				return;
@@ -445,8 +445,8 @@
 		 * (it wasn't before, if it is now is because nv
 		 *  decreased it).
 		 */
-		if (tp->snd_cwnd < nv_min_cwnd)
-			tp->snd_cwnd = nv_min_cwnd;
+		if (tcp_snd_cwnd(tp) < nv_min_cwnd)
+			tcp_snd_cwnd_set(tp, nv_min_cwnd);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_offload.c
@@ -11,12 +11,15 @@
 #include <net/tcp.h>
 #include <net/protocol.h>
 
-static void tcp_gso_tstamp(struct sk_buff *skb, unsigned int ts_seq,
+static void tcp_gso_tstamp(struct sk_buff *skb, struct sk_buff *gso_skb,
 			   unsigned int seq, unsigned int mss)
 {
+	u32 flags = skb_shinfo(gso_skb)->tx_flags & SKBTX_ANY_TSTAMP;
+	u32 ts_seq = skb_shinfo(gso_skb)->tskey;
+
 	while (skb) {
 		if (before(ts_seq, seq + mss)) {
-			skb_shinfo(skb)->tx_flags |= SKBTX_SW_TSTAMP;
+			skb_shinfo(skb)->tx_flags |= flags;
 			skb_shinfo(skb)->tskey = ts_seq;
 			return;
 		}
@@ -71,6 +74,9 @@
 	if (thlen < sizeof(*th))
 		goto out;
 
+	if (unlikely(skb_checksum_start(skb) != skb_transport_header(skb)))
+		goto out;
+
 	if (!pskb_may_pull(skb, thlen))
 		goto out;
 
@@ -115,8 +121,8 @@
 	th = tcp_hdr(skb);
 	seq = ntohl(th->seq);
 
-	if (unlikely(skb_shinfo(gso_skb)->tx_flags & SKBTX_SW_TSTAMP))
-		tcp_gso_tstamp(segs, skb_shinfo(gso_skb)->tskey, seq, mss);
+	if (unlikely(skb_shinfo(gso_skb)->tx_flags & SKBTX_ANY_TSTAMP))
+		tcp_gso_tstamp(segs, gso_skb, seq, mss);
 
 	newcheck = ~csum_fold((__force __wsum)((__force u32)th->check +
 					       (__force u32)delta));
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_output.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_output.c
@@ -82,6 +82,7 @@
 
 	NET_ADD_STATS(sock_net(sk), LINUX_MIB_TCPORIGDATASENT,
 		      tcp_skb_pcount(skb));
+	tcp_check_space(sk);
 }
 
 /* SND.NXT, if window was not shrunk or the amount of shrunk was less than one
@@ -142,7 +143,7 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	u32 restart_cwnd = tcp_init_cwnd(tp, __sk_dst_get(sk));
-	u32 cwnd = tp->snd_cwnd;
+	u32 cwnd = tcp_snd_cwnd(tp);
 
 	tcp_ca_event(sk, CA_EVENT_CWND_RESTART);
 
@@ -151,7 +152,7 @@
 
 	while ((delta -= inet_csk(sk)->icsk_rto) > 0 && cwnd > restart_cwnd)
 		cwnd >>= 1;
-	tp->snd_cwnd = max(cwnd, restart_cwnd);
+	tcp_snd_cwnd_set(tp, max(cwnd, restart_cwnd));
 	tp->snd_cwnd_stamp = tcp_jiffies32;
 	tp->snd_cwnd_used = 0;
 }
@@ -166,21 +167,17 @@
 	if (tcp_packets_in_flight(tp) == 0)
 		tcp_ca_event(sk, CA_EVENT_TX_START);
 
-	/* If this is the first data packet sent in response to the
-	 * previous received data,
-	 * and it is a reply for ato after last received packet,
-	 * increase pingpong count.
-	 */
-	if (before(tp->lsndtime, icsk->icsk_ack.lrcvtime) &&
-	    (u32)(now - icsk->icsk_ack.lrcvtime) < icsk->icsk_ack.ato)
-		inet_csk_inc_pingpong_cnt(sk);
-
 	tp->lsndtime = now;
+
+	/* If it is a reply for ato after last received
+	 * packet, enter pingpong mode.
+	 */
+	if ((u32)(now - icsk->icsk_ack.lrcvtime) < icsk->icsk_ack.ato)
+		inet_csk_enter_pingpong_mode(sk);
 }
 
 /* Account for an ACK we sent. */
-static inline void tcp_event_ack_sent(struct sock *sk, unsigned int pkts,
-				      u32 rcv_nxt)
+static inline void tcp_event_ack_sent(struct sock *sk, u32 rcv_nxt)
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 
@@ -194,7 +191,7 @@
 
 	if (unlikely(rcv_nxt != tp->rcv_nxt))
 		return;  /* Special ACK sent by DCTCP to reflect ECN */
-	tcp_dec_quickack_mode(sk, pkts);
+	tcp_dec_quickack_mode(sk);
 	inet_csk_clear_xmit_timer(sk, ICSK_TIME_DACK);
 }
 
@@ -240,8 +237,8 @@
 	*rcv_wscale = 0;
 	if (wscale_ok) {
 		/* Set window scaling on max possible window */
-		space = max_t(u32, space, sock_net(sk)->ipv4.sysctl_tcp_rmem[2]);
-		space = max_t(u32, space, sysctl_rmem_max);
+		space = max_t(u32, space, READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[2]));
+		space = max_t(u32, space, READ_ONCE(sysctl_rmem_max));
 		space = min_t(u32, space, *window_clamp);
 		*rcv_wscale = clamp_t(int, ilog2(space) - 15,
 				      0, TCP_MAX_WSCALE);
@@ -323,7 +320,7 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	bool bpf_needs_ecn = tcp_bpf_ca_needs_ecn(sk);
-	bool use_ecn = sock_net(sk)->ipv4.sysctl_tcp_ecn == 1 ||
+	bool use_ecn = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_ecn) == 1 ||
 		tcp_ca_needs_ecn(sk) || bpf_needs_ecn;
 
 	if (!use_ecn) {
@@ -345,7 +342,7 @@
 
 static void tcp_ecn_clear_syn(struct sock *sk, struct sk_buff *skb)
 {
-	if (sock_net(sk)->ipv4.sysctl_tcp_ecn_fallback)
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_ecn_fallback))
 		/* tp->ecn_flags are cleared at a later point in time when
 		 * SYN ACK is ultimatively being received.
 		 */
@@ -789,18 +786,18 @@
 	opts->mss = tcp_advertise_mss(sk);
 	remaining -= TCPOLEN_MSS_ALIGNED;
 
-	if (likely(sock_net(sk)->ipv4.sysctl_tcp_timestamps && !*md5)) {
+	if (likely(READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_timestamps) && !*md5)) {
 		opts->options |= OPTION_TS;
 		opts->tsval = tcp_skb_timestamp(skb) + tp->tsoffset;
 		opts->tsecr = tp->rx_opt.ts_recent;
 		remaining -= TCPOLEN_TSTAMP_ALIGNED;
 	}
-	if (likely(sock_net(sk)->ipv4.sysctl_tcp_window_scaling)) {
+	if (likely(READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_window_scaling))) {
 		opts->ws = tp->rx_opt.rcv_wscale;
 		opts->options |= OPTION_WSCALE;
 		remaining -= TCPOLEN_WSCALE_ALIGNED;
 	}
-	if (likely(sock_net(sk)->ipv4.sysctl_tcp_sack)) {
+	if (likely(READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_sack))) {
 		opts->options |= OPTION_SACK_ADVERTISE;
 		if (unlikely(!(OPTION_TS & opts->options)))
 			remaining -= TCPOLEN_SACKPERM_ALIGNED;
@@ -827,8 +824,10 @@
 		unsigned int size;
 
 		if (mptcp_syn_options(sk, skb, &size, &opts->mptcp)) {
-			opts->options |= OPTION_MPTCP;
-			remaining -= size;
+			if (remaining >= size) {
+				opts->options |= OPTION_MPTCP;
+				remaining -= size;
+			}
 		}
 	}
 
@@ -877,7 +876,7 @@
 	if (likely(ireq->tstamp_ok)) {
 		opts->options |= OPTION_TS;
 		opts->tsval = tcp_skb_timestamp(skb) + tcp_rsk(req)->ts_off;
-		opts->tsecr = req->ts_recent;
+		opts->tsecr = READ_ONCE(req->ts_recent);
 		remaining -= TCPOLEN_TSTAMP_ALIGNED;
 	}
 	if (likely(ireq->sack_ok)) {
@@ -1014,7 +1013,7 @@
 		struct tcp_sock *tp = tcp_sk(sk);
 
 		if (tp->lost_out > tp->retrans_out &&
-		    tp->snd_cwnd > tcp_packets_in_flight(tp)) {
+		    tcp_snd_cwnd(tp) > tcp_packets_in_flight(tp)) {
 			tcp_mstamp_refresh(tp);
 			tcp_xmit_retransmit_queue(sk);
 		}
@@ -1321,7 +1320,7 @@
 	skb->destructor = skb_is_tcp_pure_ack(skb) ? __sock_wfree : tcp_wfree;
 	refcount_add(skb->truesize, &sk->sk_wmem_alloc);
 
-	skb_set_dst_pending_confirm(skb, sk->sk_dst_pending_confirm);
+	skb_set_dst_pending_confirm(skb, READ_ONCE(sk->sk_dst_pending_confirm));
 
 	/* Build TCP header and checksum it. */
 	th = (struct tcphdr *)skb->data;
@@ -1376,7 +1375,7 @@
 			   sk, skb);
 
 	if (likely(tcb->tcp_flags & TCPHDR_ACK))
-		tcp_event_ack_sent(sk, tcp_skb_pcount(skb), rcv_nxt);
+		tcp_event_ack_sent(sk, rcv_nxt);
 
 	if (skb->len != tcp_header_size) {
 		tcp_event_data_sent(tp, sk);
@@ -1562,7 +1561,7 @@
 		return -ENOMEM;
 	}
 
-	if (skb_unclone(skb, gfp))
+	if (skb_unclone_keeptruesize(skb, gfp))
 		return -ENOMEM;
 
 	/* Get a new skb... force flag on. */
@@ -1672,7 +1671,7 @@
 {
 	u32 delta_truesize;
 
-	if (skb_unclone(skb, GFP_ATOMIC))
+	if (skb_unclone_keeptruesize(skb, GFP_ATOMIC))
 		return -ENOMEM;
 
 	delta_truesize = __pskb_trim_head(skb, len);
@@ -1721,7 +1720,8 @@
 	mss_now -= icsk->icsk_ext_hdr_len;
 
 	/* Then reserve room for full set of TCP options and 8 bytes of data */
-	mss_now = max(mss_now, sock_net(sk)->ipv4.sysctl_tcp_min_snd_mss);
+	mss_now = max(mss_now,
+		      READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_min_snd_mss));
 	return mss_now;
 }
 
@@ -1764,10 +1764,10 @@
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct net *net = sock_net(sk);
 
-	icsk->icsk_mtup.enabled = net->ipv4.sysctl_tcp_mtu_probing > 1;
+	icsk->icsk_mtup.enabled = READ_ONCE(net->ipv4.sysctl_tcp_mtu_probing) > 1;
 	icsk->icsk_mtup.search_high = tp->rx_opt.mss_clamp + sizeof(struct tcphdr) +
 			       icsk->icsk_af_ops->net_header_len;
-	icsk->icsk_mtup.search_low = tcp_mss_to_mtu(sk, net->ipv4.sysctl_tcp_base_mss);
+	icsk->icsk_mtup.search_low = tcp_mss_to_mtu(sk, READ_ONCE(net->ipv4.sysctl_tcp_base_mss));
 	icsk->icsk_mtup.probe_size = 0;
 	if (icsk->icsk_mtup.enabled)
 		icsk->icsk_mtup.probe_timestamp = tcp_jiffies32;
@@ -1865,9 +1865,9 @@
 		/* Limited by application or receiver window. */
 		u32 init_win = tcp_init_cwnd(tp, __sk_dst_get(sk));
 		u32 win_used = max(tp->snd_cwnd_used, init_win);
-		if (win_used < tp->snd_cwnd) {
+		if (win_used < tcp_snd_cwnd(tp)) {
 			tp->snd_ssthresh = tcp_current_ssthresh(sk);
-			tp->snd_cwnd = (tp->snd_cwnd + win_used) >> 1;
+			tcp_snd_cwnd_set(tp, (tcp_snd_cwnd(tp) + win_used) >> 1);
 		}
 		tp->snd_cwnd_used = 0;
 	}
@@ -1879,15 +1879,20 @@
 	const struct tcp_congestion_ops *ca_ops = inet_csk(sk)->icsk_ca_ops;
 	struct tcp_sock *tp = tcp_sk(sk);
 
-	/* Track the maximum number of outstanding packets in each
-	 * window, and remember whether we were cwnd-limited then.
-	 */
-	if (!before(tp->snd_una, tp->max_packets_seq) ||
-	    tp->packets_out > tp->max_packets_out ||
-	    is_cwnd_limited) {
-		tp->max_packets_out = tp->packets_out;
-		tp->max_packets_seq = tp->snd_nxt;
+	/* Track the strongest available signal of the degree to which the cwnd
+	 * is fully utilized. If cwnd-limited then remember that fact for the
+	 * current window. If not cwnd-limited then track the maximum number of
+	 * outstanding packets in the current window. (If cwnd-limited then we
+	 * chose to not update tp->max_packets_out to avoid an extra else
+	 * clause with no functional impact.)
+	 */
+	if (!before(tp->snd_una, tp->cwnd_usage_seq) ||
+	    is_cwnd_limited ||
+	    (!tp->is_cwnd_limited &&
+	     tp->packets_out > tp->max_packets_out)) {
 		tp->is_cwnd_limited = is_cwnd_limited;
+		tp->max_packets_out = tp->packets_out;
+		tp->cwnd_usage_seq = tp->snd_nxt;
 	}
 
 	if (tcp_is_cwnd_limited(sk)) {
@@ -1899,7 +1904,7 @@
 		if (tp->packets_out > tp->snd_cwnd_used)
 			tp->snd_cwnd_used = tp->packets_out;
 
-		if (sock_net(sk)->ipv4.sysctl_tcp_slow_start_after_idle &&
+		if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_slow_start_after_idle) &&
 		    (s32)(tcp_jiffies32 - tp->snd_cwnd_stamp) >= inet_csk(sk)->icsk_rto &&
 		    !ca_ops->cong_control)
 			tcp_cwnd_application_limited(sk);
@@ -1987,7 +1992,7 @@
 
 	min_tso = ca_ops->min_tso_segs ?
 			ca_ops->min_tso_segs(sk) :
-			sock_net(sk)->ipv4.sysctl_tcp_min_tso_segs;
+			READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_min_tso_segs);
 
 	tso_segs = tcp_tso_autosize(sk, mss_now, min_tso);
 	return min_t(u32, tso_segs, sk->sk_gso_max_segs);
@@ -2039,7 +2044,7 @@
 		return 1;
 
 	in_flight = tcp_packets_in_flight(tp);
-	cwnd = tp->snd_cwnd;
+	cwnd = tcp_snd_cwnd(tp);
 	if (in_flight >= cwnd)
 		return 0;
 
@@ -2196,12 +2201,12 @@
 	in_flight = tcp_packets_in_flight(tp);
 
 	BUG_ON(tcp_skb_pcount(skb) <= 1);
-	BUG_ON(tp->snd_cwnd <= in_flight);
+	BUG_ON(tcp_snd_cwnd(tp) <= in_flight);
 
 	send_win = tcp_wnd_end(tp) - TCP_SKB_CB(skb)->seq;
 
 	/* From in_flight test above, we know that cwnd > in_flight.  */
-	cong_win = (tp->snd_cwnd - in_flight) * tp->mss_cache;
+	cong_win = (tcp_snd_cwnd(tp) - in_flight) * tp->mss_cache;
 
 	limit = min(send_win, cong_win);
 
@@ -2215,7 +2220,7 @@
 
 	win_divisor = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_tso_win_divisor);
 	if (win_divisor) {
-		u32 chunk = min(tp->snd_wnd, tp->snd_cwnd * tp->mss_cache);
+		u32 chunk = min(tp->snd_wnd, tcp_snd_cwnd(tp) * tp->mss_cache);
 
 		/* If at least some fraction of a window is available,
 		 * just use it.
@@ -2279,7 +2284,7 @@
 	u32 interval;
 	s32 delta;
 
-	interval = net->ipv4.sysctl_tcp_probe_interval;
+	interval = READ_ONCE(net->ipv4.sysctl_tcp_probe_interval);
 	delta = tcp_jiffies32 - icsk->icsk_mtup.probe_timestamp;
 	if (unlikely(delta >= interval * HZ)) {
 		int mss = tcp_current_mss(sk);
@@ -2305,7 +2310,7 @@
 		if (len <= skb->len)
 			break;
 
-		if (unlikely(TCP_SKB_CB(skb)->eor) || tcp_has_tx_tstamp(skb))
+		if (tcp_has_tx_tstamp(skb) || !tcp_skb_can_collapse(skb, next))
 			return false;
 
 		len -= skb->len;
@@ -2343,7 +2348,7 @@
 	if (likely(!icsk->icsk_mtup.enabled ||
 		   icsk->icsk_mtup.probe_size ||
 		   inet_csk(sk)->icsk_ca_state != TCP_CA_Open ||
-		   tp->snd_cwnd < 11 ||
+		   tcp_snd_cwnd(tp) < 11 ||
 		   tp->rx_opt.num_sacks || tp->rx_opt.dsack))
 		return -1;
 
@@ -2361,7 +2366,7 @@
 	 * probing process by not resetting search range to its orignal.
 	 */
 	if (probe_size > tcp_mtu_to_mss(sk, icsk->icsk_mtup.search_high) ||
-		interval < net->ipv4.sysctl_tcp_probe_threshold) {
+	    interval < READ_ONCE(net->ipv4.sysctl_tcp_probe_threshold)) {
 		/* Check whether enough time has elaplased for
 		 * another round of probing.
 		 */
@@ -2379,7 +2384,7 @@
 		return 0;
 
 	/* Do we need to wait to drain cwnd? With none in flight, don't stall */
-	if (tcp_packets_in_flight(tp) + 2 > tp->snd_cwnd) {
+	if (tcp_packets_in_flight(tp) + 2 > tcp_snd_cwnd(tp)) {
 		if (!tcp_packets_in_flight(tp))
 			return -1;
 		else
@@ -2451,7 +2456,7 @@
 	if (!tcp_transmit_skb(sk, nskb, 1, GFP_ATOMIC)) {
 		/* Decrement cwnd here because we are sending
 		 * effectively two packets. */
-		tp->snd_cwnd--;
+		tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) - 1);
 		tcp_event_new_data_sent(sk, nskb);
 
 		icsk->icsk_mtup.probe_size = tcp_mss_to_mtu(sk, nskb->len);
@@ -2483,6 +2488,18 @@
 	return true;
 }
 
+static bool tcp_rtx_queue_empty_or_single_skb(const struct sock *sk)
+{
+	const struct rb_node *node = sk->tcp_rtx_queue.rb_node;
+
+	/* No skb in the rtx queue. */
+	if (!node)
+		return true;
+
+	/* Only one skb in rtx queue. */
+	return !node->rb_left && !node->rb_right;
+}
+
 /* TCP Small Queues :
  * Control number of packets in qdisc/devices to two packets / or ~1 ms.
  * (These limits are doubled for retransmits)
@@ -2504,7 +2521,7 @@
 		      sk->sk_pacing_rate >> READ_ONCE(sk->sk_pacing_shift));
 	if (sk->sk_pacing_status == SK_PACING_NONE)
 		limit = min_t(unsigned long, limit,
-			      sock_net(sk)->ipv4.sysctl_tcp_limit_output_bytes);
+			      READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_limit_output_bytes));
 	limit <<= factor;
 
 	if (static_branch_unlikely(&tcp_tx_delay_enabled) &&
@@ -2520,12 +2537,12 @@
 		limit += extra_bytes;
 	}
 	if (refcount_read(&sk->sk_wmem_alloc) > limit) {
-		/* Always send skb if rtx queue is empty.
+		/* Always send skb if rtx queue is empty or has one skb.
 		 * No need to wait for TX completion to call us back,
 		 * after softirq/tasklet schedule.
 		 * This helps when TX completions are delayed too much.
 		 */
-		if (tcp_rtx_queue_empty(sk))
+		if (tcp_rtx_queue_empty_or_single_skb(sk))
 			return false;
 
 		set_bit(TSQ_THROTTLED, &sk->sk_tsq_flags);
@@ -2708,7 +2725,7 @@
 	else
 		tcp_chrono_stop(sk, TCP_CHRONO_RWND_LIMITED);
 
-	is_cwnd_limited |= (tcp_packets_in_flight(tp) >= tp->snd_cwnd);
+	is_cwnd_limited |= (tcp_packets_in_flight(tp) >= tcp_snd_cwnd(tp));
 	if (likely(sent_pkts || is_cwnd_limited))
 		tcp_cwnd_validate(sk, is_cwnd_limited);
 
@@ -2728,7 +2745,7 @@
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
-	u32 timeout, rto_delta_us;
+	u32 timeout, timeout_us, rto_delta_us;
 	int early_retrans;
 
 	/* Don't do any loss probe on a Fast Open connection before 3WHS
@@ -2737,7 +2754,7 @@
 	if (rcu_access_pointer(tp->fastopen_rsk))
 		return false;
 
-	early_retrans = sock_net(sk)->ipv4.sysctl_tcp_early_retrans;
+	early_retrans = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_early_retrans);
 	/* Schedule a loss probe in 2*RTT for SACK capable connections
 	 * not in loss recovery, that are either limited by cwnd or application.
 	 */
@@ -2752,11 +2769,12 @@
 	 * sample is available then probe after TCP_TIMEOUT_INIT.
 	 */
 	if (tp->srtt_us) {
-		timeout = usecs_to_jiffies(tp->srtt_us >> 2);
+		timeout_us = tp->srtt_us >> 2;
 		if (tp->packets_out == 1)
-			timeout += TCP_RTO_MIN;
+			timeout_us += tcp_rto_min_us(sk);
 		else
-			timeout += TCP_TIMEOUT_MIN;
+			timeout_us += TCP_TIMEOUT_MIN_US;
+		timeout = usecs_to_jiffies(timeout_us);
 	} else {
 		timeout = TCP_TIMEOUT_INIT;
 	}
@@ -2818,7 +2836,7 @@
 	if (unlikely(!skb)) {
 		WARN_ONCE(tp->packets_out,
 			  "invalid inflight: %u state %u cwnd %u mss %d\n",
-			  tp->packets_out, sk->sk_state, tp->snd_cwnd, mss);
+			  tp->packets_out, sk->sk_state, tcp_snd_cwnd(tp), mss);
 		inet_csk(sk)->icsk_pending = 0;
 		return;
 	}
@@ -3106,7 +3124,7 @@
 	struct sk_buff *skb = to, *tmp;
 	bool first = true;
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_retrans_collapse)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_retrans_collapse))
 		return;
 	if (TCP_SKB_CB(skb)->tcp_flags & TCPHDR_SYN)
 		return;
@@ -3146,7 +3164,7 @@
 	struct tcp_sock *tp = tcp_sk(sk);
 	unsigned int cur_mss;
 	int diff, len, err;
-
+	int avail_wnd;
 
 	/* Inconclusive MTU probe */
 	if (icsk->icsk_mtup.probe_size)
@@ -3155,7 +3173,13 @@
 	if (skb_still_in_host_queue(sk, skb))
 		return -EBUSY;
 
+start:
 	if (before(TCP_SKB_CB(skb)->seq, tp->snd_una)) {
+		if (unlikely(TCP_SKB_CB(skb)->tcp_flags & TCPHDR_SYN)) {
+			TCP_SKB_CB(skb)->tcp_flags &= ~TCPHDR_SYN;
+			TCP_SKB_CB(skb)->seq++;
+			goto start;
+		}
 		if (unlikely(before(TCP_SKB_CB(skb)->end_seq, tp->snd_una))) {
 			WARN_ON_ONCE(1);
 			return -EINVAL;
@@ -3168,23 +3192,31 @@
 		return -EHOSTUNREACH; /* Routing failure or similar. */
 
 	cur_mss = tcp_current_mss(sk);
+	avail_wnd = tcp_wnd_end(tp) - TCP_SKB_CB(skb)->seq;
 
 	/* If receiver has shrunk his window, and skb is out of
 	 * new window, do not retransmit it. The exception is the
 	 * case, when window is shrunk to zero. In this case
-	 * our retransmit serves as a zero window probe.
+	 * our retransmit of one segment serves as a zero window probe.
 	 */
-	if (!before(TCP_SKB_CB(skb)->seq, tcp_wnd_end(tp)) &&
-	    TCP_SKB_CB(skb)->seq != tp->snd_una)
-		return -EAGAIN;
+	if (avail_wnd <= 0) {
+		if (TCP_SKB_CB(skb)->seq != tp->snd_una)
+			return -EAGAIN;
+		avail_wnd = cur_mss;
+	}
 
 	len = cur_mss * segs;
+	if (len > avail_wnd) {
+		len = rounddown(avail_wnd, cur_mss);
+		if (!len)
+			len = avail_wnd;
+	}
 	if (skb->len > len) {
 		if (tcp_fragment(sk, TCP_FRAG_IN_RTX_QUEUE, skb, len,
 				 cur_mss, GFP_ATOMIC))
 			return -ENOMEM; /* We'll try again later. */
 	} else {
-		if (skb_unclone(skb, GFP_ATOMIC))
+		if (skb_unclone_keeptruesize(skb, GFP_ATOMIC))
 			return -ENOMEM;
 
 		diff = tcp_skb_pcount(skb);
@@ -3192,8 +3224,9 @@
 		diff -= tcp_skb_pcount(skb);
 		if (diff)
 			tcp_adjust_pcount(sk, skb, diff);
-		if (skb->len < cur_mss)
-			tcp_retrans_try_collapse(sk, skb, cur_mss);
+		avail_wnd = min_t(int, avail_wnd, cur_mss);
+		if (skb->len < avail_wnd)
+			tcp_retrans_try_collapse(sk, skb, avail_wnd);
 	}
 
 	/* RFC3168, section 6.1.1.1. ECN fallback */
@@ -3307,7 +3340,7 @@
 		if (!hole)
 			tp->retransmit_skb_hint = skb;
 
-		segs = tp->snd_cwnd - tcp_packets_in_flight(tp);
+		segs = tcp_snd_cwnd(tp) - tcp_packets_in_flight(tp);
 		if (segs <= 0)
 			break;
 		sacked = TCP_SKB_CB(skb)->sacked;
@@ -3364,11 +3397,12 @@
  */
 void sk_forced_mem_schedule(struct sock *sk, int size)
 {
-	int amt;
+	int delta, amt;
 
-	if (size <= sk->sk_forward_alloc)
+	delta = size - sk->sk_forward_alloc;
+	if (delta <= 0)
 		return;
-	amt = sk_mem_pages(size);
+	amt = sk_mem_pages(delta);
 	sk->sk_forward_alloc += amt * SK_MEM_QUANTUM;
 	sk_memory_allocated_add(sk, amt);
 
@@ -3409,7 +3443,9 @@
 			return;
 		}
 	} else {
-		skb = alloc_skb_fclone(MAX_TCP_HEADER, sk->sk_allocation);
+		skb = alloc_skb_fclone(MAX_TCP_HEADER,
+				       sk_gfp_mask(sk, GFP_ATOMIC |
+						       __GFP_NOWARN));
 		if (unlikely(!skb))
 			return;
 
@@ -3596,7 +3632,7 @@
 	th->window = htons(min(req->rsk_rcv_wnd, 65535U));
 	tcp_options_write((__be32 *)(th + 1), NULL, &opts);
 	th->doff = (tcp_header_size >> 2);
-	__TCP_INC_STATS(sock_net(sk), TCP_MIB_OUTSEGS);
+	TCP_INC_STATS(sock_net(sk), TCP_MIB_OUTSEGS);
 
 #ifdef CONFIG_TCP_MD5SIG
 	/* Okay, we have all we need - do the md5 hash if needed */
@@ -3647,7 +3683,7 @@
 	 * See tcp_input.c:tcp_rcv_state_process case TCP_SYN_SENT.
 	 */
 	tp->tcp_header_len = sizeof(struct tcphdr);
-	if (sock_net(sk)->ipv4.sysctl_tcp_timestamps)
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_timestamps))
 		tp->tcp_header_len += TCPOLEN_TSTAMP_ALIGNED;
 
 #ifdef CONFIG_TCP_MD5SIG
@@ -3683,14 +3719,14 @@
 				  tp->advmss - (tp->rx_opt.ts_recent_stamp ? tp->tcp_header_len - sizeof(struct tcphdr) : 0),
 				  &tp->rcv_wnd,
 				  &tp->window_clamp,
-				  sock_net(sk)->ipv4.sysctl_tcp_window_scaling,
+				  READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_window_scaling),
 				  &rcv_wscale,
 				  rcv_wnd);
 
 	tp->rx_opt.rcv_wscale = rcv_wscale;
 	tp->rcv_ssthresh = tp->rcv_wnd;
 
-	sk->sk_err = 0;
+	WRITE_ONCE(sk->sk_err, 0);
 	sock_reset_flag(sk, SOCK_DONE);
 	tp->snd_wnd = 0;
 	tcp_init_wl(tp, 0);
@@ -3734,6 +3770,7 @@
  */
 static int tcp_send_syn_data(struct sock *sk, struct sk_buff *syn)
 {
+	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct tcp_fastopen_request *fo = tp->fastopen_req;
 	int space, err = 0;
@@ -3748,8 +3785,10 @@
 	 * private TCP options. The cost is reduced data space in SYN :(
 	 */
 	tp->rx_opt.mss_clamp = tcp_mss_clamp(tp, tp->rx_opt.mss_clamp);
+	/* Sync mss_cache after updating the mss_clamp */
+	tcp_sync_mss(sk, icsk->icsk_pmtu_cookie);
 
-	space = __tcp_mtu_to_mss(sk, inet_csk(sk)->icsk_pmtu_cookie) -
+	space = __tcp_mtu_to_mss(sk, icsk->icsk_pmtu_cookie) -
 		MAX_TCP_OPTION_SPACE;
 
 	space = min_t(size_t, space, fo->size);
@@ -4088,7 +4127,7 @@
 
 	icsk->icsk_probes_out++;
 	if (err <= 0) {
-		if (icsk->icsk_backoff < net->ipv4.sysctl_tcp_retries2)
+		if (icsk->icsk_backoff < READ_ONCE(net->ipv4.sysctl_tcp_retries2))
 			icsk->icsk_backoff++;
 		timeout = tcp_probe0_when(sk, TCP_RTO_MAX);
 	} else {
@@ -4112,8 +4151,8 @@
 	res = af_ops->send_synack(sk, NULL, &fl, req, NULL, TCP_SYNACK_NORMAL,
 				  NULL);
 	if (!res) {
-		__TCP_INC_STATS(sock_net(sk), TCP_MIB_RETRANSSEGS);
-		__NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPSYNRETRANS);
+		TCP_INC_STATS(sock_net(sk), TCP_MIB_RETRANSSEGS);
+		NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPSYNRETRANS);
 		if (unlikely(tcp_passive_fastopen(sk)))
 			tcp_sk(sk)->total_retrans++;
 		trace_tcp_retransmit_synack(sk, req);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_rate.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_rate.c
@@ -73,26 +73,31 @@
  *
  * If an ACK (s)acks multiple skbs (e.g., stretched-acks), this function is
  * called multiple times. We favor the information from the most recently
- * sent skb, i.e., the skb with the highest prior_delivered count.
+ * sent skb, i.e., the skb with the most recently sent time and the highest
+ * sequence.
  */
 void tcp_rate_skb_delivered(struct sock *sk, struct sk_buff *skb,
 			    struct rate_sample *rs)
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct tcp_skb_cb *scb = TCP_SKB_CB(skb);
+	u64 tx_tstamp;
 
 	if (!scb->tx.delivered_mstamp)
 		return;
 
+	tx_tstamp = tcp_skb_timestamp_us(skb);
 	if (!rs->prior_delivered ||
-	    after(scb->tx.delivered, rs->prior_delivered)) {
+	    tcp_skb_sent_after(tx_tstamp, tp->first_tx_mstamp,
+			       scb->end_seq, rs->last_end_seq)) {
 		rs->prior_delivered  = scb->tx.delivered;
 		rs->prior_mstamp     = scb->tx.delivered_mstamp;
 		rs->is_app_limited   = scb->tx.is_app_limited;
 		rs->is_retrans	     = scb->sacked & TCPCB_RETRANS;
+		rs->last_end_seq     = scb->end_seq;
 
 		/* Record send time of most recently ACKed packet: */
-		tp->first_tx_mstamp  = tcp_skb_timestamp_us(skb);
+		tp->first_tx_mstamp  = tx_tstamp;
 		/* Find the duration of the "send phase" of this window: */
 		rs->interval_us = tcp_stamp_us_delta(tp->first_tx_mstamp,
 						     scb->tx.first_tx_mstamp);
@@ -189,7 +194,7 @@
 	    /* Nothing in sending host's qdisc queues or NIC tx queue. */
 	    sk_wmem_alloc_get(sk) < SKB_TRUESIZE(1) &&
 	    /* We are not limited by CWND. */
-	    tcp_packets_in_flight(tp) < tp->snd_cwnd &&
+	    tcp_packets_in_flight(tp) < tcp_snd_cwnd(tp) &&
 	    /* All lost packets have been retransmitted. */
 	    tp->lost_out <= tp->retrans_out)
 		tp->app_limited =
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_recovery.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_recovery.c
@@ -19,7 +19,8 @@
 			return 0;
 
 		if (tp->sacked_out >= tp->reordering &&
-		    !(sock_net(sk)->ipv4.sysctl_tcp_recovery & TCP_RACK_NO_DUPTHRESH))
+		    !(READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_recovery) &
+		      TCP_RACK_NO_DUPTHRESH))
 			return 0;
 	}
 
@@ -108,7 +109,7 @@
 	tp->rack.advanced = 0;
 	tcp_rack_detect_loss(sk, &timeout);
 	if (timeout) {
-		timeout = usecs_to_jiffies(timeout) + TCP_TIMEOUT_MIN;
+		timeout = usecs_to_jiffies(timeout + TCP_TIMEOUT_MIN_US);
 		inet_csk_reset_xmit_timer(sk, ICSK_TIME_REO_TIMEOUT,
 					  timeout, inet_csk(sk)->icsk_rto);
 	}
@@ -192,7 +193,8 @@
 {
 	struct tcp_sock *tp = tcp_sk(sk);
 
-	if (sock_net(sk)->ipv4.sysctl_tcp_recovery & TCP_RACK_STATIC_REO_WND ||
+	if ((READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_recovery) &
+	     TCP_RACK_STATIC_REO_WND) ||
 	    !rs->prior_delivered)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_scalable.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_scalable.c
@@ -27,7 +27,7 @@
 		if (!acked)
 			return;
 	}
-	tcp_cong_avoid_ai(tp, min(tp->snd_cwnd, TCP_SCALABLE_AI_CNT),
+	tcp_cong_avoid_ai(tp, min(tcp_snd_cwnd(tp), TCP_SCALABLE_AI_CNT),
 			  acked);
 }
 
@@ -35,7 +35,7 @@
 {
 	const struct tcp_sock *tp = tcp_sk(sk);
 
-	return max(tp->snd_cwnd - (tp->snd_cwnd>>TCP_SCALABLE_MD_SCALE), 2U);
+	return max(tcp_snd_cwnd(tp) - (tcp_snd_cwnd(tp)>>TCP_SCALABLE_MD_SCALE), 2U);
 }
 
 static struct tcp_congestion_ops tcp_scalable __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_timer.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_timer.c
@@ -67,11 +67,7 @@
 
 static void tcp_write_err(struct sock *sk)
 {
-	sk->sk_err = sk->sk_err_soft ? : ETIMEDOUT;
-	sk_error_report(sk);
-
-	tcp_write_queue_purge(sk);
-	tcp_done(sk);
+	tcp_done_with_error(sk, READ_ONCE(sk->sk_err_soft) ? : ETIMEDOUT);
 	__NET_INC_STATS(sock_net(sk), LINUX_MIB_TCPABORTONTIMEOUT);
 }
 
@@ -110,7 +106,7 @@
 		shift++;
 
 	/* If some dubious ICMP arrived, penalize even more. */
-	if (sk->sk_err_soft)
+	if (READ_ONCE(sk->sk_err_soft))
 		shift++;
 
 	if (tcp_check_oom(sk, shift)) {
@@ -143,10 +139,10 @@
  */
 static int tcp_orphan_retries(struct sock *sk, bool alive)
 {
-	int retries = sock_net(sk)->ipv4.sysctl_tcp_orphan_retries; /* May be zero. */
+	int retries = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_orphan_retries); /* May be zero. */
 
 	/* We know from an ICMP that something is wrong. */
-	if (sk->sk_err_soft && !alive)
+	if (READ_ONCE(sk->sk_err_soft) && !alive)
 		retries = 0;
 
 	/* However, if socket sent something recently, select some safe
@@ -163,7 +159,7 @@
 	int mss;
 
 	/* Black hole detection */
-	if (!net->ipv4.sysctl_tcp_mtu_probing)
+	if (!READ_ONCE(net->ipv4.sysctl_tcp_mtu_probing))
 		return;
 
 	if (!icsk->icsk_mtup.enabled) {
@@ -171,9 +167,9 @@
 		icsk->icsk_mtup.probe_timestamp = tcp_jiffies32;
 	} else {
 		mss = tcp_mtu_to_mss(sk, icsk->icsk_mtup.search_low) >> 1;
-		mss = min(net->ipv4.sysctl_tcp_base_mss, mss);
-		mss = max(mss, net->ipv4.sysctl_tcp_mtu_probe_floor);
-		mss = max(mss, net->ipv4.sysctl_tcp_min_snd_mss);
+		mss = min(READ_ONCE(net->ipv4.sysctl_tcp_base_mss), mss);
+		mss = max(mss, READ_ONCE(net->ipv4.sysctl_tcp_mtu_probe_floor));
+		mss = max(mss, READ_ONCE(net->ipv4.sysctl_tcp_min_snd_mss));
 		icsk->icsk_mtup.search_low = tcp_mss_to_mtu(sk, mss);
 	}
 	tcp_sync_mss(sk, icsk->icsk_pmtu_cookie);
@@ -239,17 +235,18 @@
 	if ((1 << sk->sk_state) & (TCPF_SYN_SENT | TCPF_SYN_RECV)) {
 		if (icsk->icsk_retransmits)
 			__dst_negative_advice(sk);
-		retry_until = icsk->icsk_syn_retries ? : net->ipv4.sysctl_tcp_syn_retries;
+		retry_until = icsk->icsk_syn_retries ? :
+			READ_ONCE(net->ipv4.sysctl_tcp_syn_retries);
 		expired = icsk->icsk_retransmits >= retry_until;
 	} else {
-		if (retransmits_timed_out(sk, net->ipv4.sysctl_tcp_retries1, 0)) {
+		if (retransmits_timed_out(sk, READ_ONCE(net->ipv4.sysctl_tcp_retries1), 0)) {
 			/* Black hole detection */
 			tcp_mtu_probing(icsk, sk);
 
 			__dst_negative_advice(sk);
 		}
 
-		retry_until = net->ipv4.sysctl_tcp_retries2;
+		retry_until = READ_ONCE(net->ipv4.sysctl_tcp_retries2);
 		if (sock_flag(sk, SOCK_DEAD)) {
 			const bool alive = icsk->icsk_rto < TCP_RTO_MAX;
 
@@ -380,7 +377,7 @@
 		 msecs_to_jiffies(icsk->icsk_user_timeout))
 		goto abort;
 
-	max_probes = sock_net(sk)->ipv4.sysctl_tcp_retries2;
+	max_probes = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_retries2);
 	if (sock_flag(sk, SOCK_DEAD)) {
 		const bool alive = inet_csk_rto_backoff(icsk, TCP_RTO_MAX) < TCP_RTO_MAX;
 
@@ -406,12 +403,15 @@
 static void tcp_fastopen_synack_timer(struct sock *sk, struct request_sock *req)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
-	int max_retries = icsk->icsk_syn_retries ? :
-	    sock_net(sk)->ipv4.sysctl_tcp_synack_retries + 1; /* add one more retry for fastopen */
 	struct tcp_sock *tp = tcp_sk(sk);
+	int max_retries;
 
 	req->rsk_ops->syn_ack_timeout(req);
 
+	/* add one more retry for fastopen */
+	max_retries = icsk->icsk_syn_retries ? :
+		READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_synack_retries) + 1;
+
 	if (req->num_timeout >= max_retries) {
 		tcp_write_err(sk);
 		return;
@@ -433,6 +433,39 @@
 			  TCP_TIMEOUT_INIT << req->num_timeout, TCP_RTO_MAX);
 }
 
+static bool tcp_rtx_probe0_timed_out(const struct sock *sk,
+				     const struct sk_buff *skb)
+{
+	const struct inet_connection_sock *icsk = inet_csk(sk);
+	u32 user_timeout = READ_ONCE(icsk->icsk_user_timeout);
+	const struct tcp_sock *tp = tcp_sk(sk);
+	int timeout = TCP_RTO_MAX * 2;
+	u32 rtx_delta;
+	s32 rcv_delta;
+
+	rtx_delta = (u32)msecs_to_jiffies(tcp_time_stamp(tp) -
+			(tp->retrans_stamp ?: tcp_skb_timestamp(skb)));
+
+	if (user_timeout) {
+		/* If user application specified a TCP_USER_TIMEOUT,
+		 * it does not want win 0 packets to 'reset the timer'
+		 * while retransmits are not making progress.
+		 */
+		if (rtx_delta > user_timeout)
+			return true;
+		timeout = min_t(u32, timeout, msecs_to_jiffies(user_timeout));
+	}
+
+	/* Note: timer interrupt might have been delayed by at least one jiffy,
+	 * and tp->rcv_tstamp might very well have been written recently.
+	 * rcv_delta can thus be negative.
+	 */
+	rcv_delta = icsk->icsk_timeout - tp->rcv_tstamp;
+	if (rcv_delta <= timeout)
+		return false;
+
+	return rtx_delta > timeout;
+}
 
 /**
  *  tcp_retransmit_timer() - The TCP retransmit timeout handler
@@ -472,8 +505,6 @@
 	if (WARN_ON_ONCE(!skb))
 		return;
 
-	tp->tlp_high_seq = 0;
-
 	if (!tp->snd_wnd && !sock_flag(sk, SOCK_DEAD) &&
 	    !((1 << sk->sk_state) & (TCPF_SYN_SENT | TCPF_SYN_RECV))) {
 		/* Receiver dastardly shrinks window. Our retransmits
@@ -498,7 +529,7 @@
 					    tp->snd_una, tp->snd_nxt);
 		}
 #endif
-		if (tcp_jiffies32 - tp->rcv_tstamp > TCP_RTO_MAX) {
+		if (tcp_rtx_probe0_timed_out(sk, skb)) {
 			tcp_write_err(sk);
 			goto out;
 		}
@@ -574,18 +605,20 @@
 	 * linear-timeout retransmissions into a black hole
 	 */
 	if (sk->sk_state == TCP_ESTABLISHED &&
-	    (tp->thin_lto || net->ipv4.sysctl_tcp_thin_linear_timeouts) &&
+	    (tp->thin_lto || READ_ONCE(net->ipv4.sysctl_tcp_thin_linear_timeouts)) &&
 	    tcp_stream_is_thin(tp) &&
 	    icsk->icsk_retransmits <= TCP_THIN_LINEAR_RETRIES) {
 		icsk->icsk_backoff = 0;
-		icsk->icsk_rto = min(__tcp_set_rto(tp), TCP_RTO_MAX);
+		icsk->icsk_rto = clamp(__tcp_set_rto(tp),
+				       tcp_rto_min(sk),
+				       TCP_RTO_MAX);
 	} else {
 		/* Use normal (exponential) backoff */
 		icsk->icsk_rto = min(icsk->icsk_rto << 1, TCP_RTO_MAX);
 	}
 	inet_csk_reset_xmit_timer(sk, ICSK_TIME_RETRANS,
 				  tcp_clamp_rto_to_user_timeout(sk), TCP_RTO_MAX);
-	if (retransmits_timed_out(sk, net->ipv4.sysctl_tcp_retries1 + 1, 0))
+	if (retransmits_timed_out(sk, READ_ONCE(net->ipv4.sysctl_tcp_retries1) + 1, 0))
 		__sk_dst_reset(sk);
 
 out:;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_ulp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_ulp.c
@@ -136,6 +136,10 @@
 	if (icsk->icsk_ulp_ops)
 		goto out_err;
 
+	err = -ENOTCONN;
+	if (!ulp_ops->clone && sk->sk_state == TCP_LISTEN)
+		goto out_err;
+
 	err = ulp_ops->init(sk);
 	if (err)
 		goto out_err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_vegas.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_vegas.c
@@ -159,7 +159,7 @@
 
 static inline u32 tcp_vegas_ssthresh(struct tcp_sock *tp)
 {
-	return  min(tp->snd_ssthresh, tp->snd_cwnd);
+	return  min(tp->snd_ssthresh, tcp_snd_cwnd(tp));
 }
 
 static void tcp_vegas_cong_avoid(struct sock *sk, u32 ack, u32 acked)
@@ -217,14 +217,14 @@
 			 * This is:
 			 *     (actual rate in segments) * baseRTT
 			 */
-			target_cwnd = (u64)tp->snd_cwnd * vegas->baseRTT;
+			target_cwnd = (u64)tcp_snd_cwnd(tp) * vegas->baseRTT;
 			do_div(target_cwnd, rtt);
 
 			/* Calculate the difference between the window we had,
 			 * and the window we would like to have. This quantity
 			 * is the "Diff" from the Arizona Vegas papers.
 			 */
-			diff = tp->snd_cwnd * (rtt-vegas->baseRTT) / vegas->baseRTT;
+			diff = tcp_snd_cwnd(tp) * (rtt-vegas->baseRTT) / vegas->baseRTT;
 
 			if (diff > gamma && tcp_in_slow_start(tp)) {
 				/* Going too fast. Time to slow down
@@ -238,7 +238,8 @@
 				 * truncation robs us of full link
 				 * utilization.
 				 */
-				tp->snd_cwnd = min(tp->snd_cwnd, (u32)target_cwnd+1);
+				tcp_snd_cwnd_set(tp, min(tcp_snd_cwnd(tp),
+							 (u32)target_cwnd + 1));
 				tp->snd_ssthresh = tcp_vegas_ssthresh(tp);
 
 			} else if (tcp_in_slow_start(tp)) {
@@ -254,14 +255,14 @@
 					/* The old window was too fast, so
 					 * we slow down.
 					 */
-					tp->snd_cwnd--;
+					tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) - 1);
 					tp->snd_ssthresh
 						= tcp_vegas_ssthresh(tp);
 				} else if (diff < alpha) {
 					/* We don't have enough extra packets
 					 * in the network, so speed up.
 					 */
-					tp->snd_cwnd++;
+					tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 				} else {
 					/* Sending just as fast as we
 					 * should be.
@@ -269,10 +270,10 @@
 				}
 			}
 
-			if (tp->snd_cwnd < 2)
-				tp->snd_cwnd = 2;
-			else if (tp->snd_cwnd > tp->snd_cwnd_clamp)
-				tp->snd_cwnd = tp->snd_cwnd_clamp;
+			if (tcp_snd_cwnd(tp) < 2)
+				tcp_snd_cwnd_set(tp, 2);
+			else if (tcp_snd_cwnd(tp) > tp->snd_cwnd_clamp)
+				tcp_snd_cwnd_set(tp, tp->snd_cwnd_clamp);
 
 			tp->snd_ssthresh = tcp_current_ssthresh(sk);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_veno.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_veno.c
@@ -146,11 +146,11 @@
 
 		rtt = veno->minrtt;
 
-		target_cwnd = (u64)tp->snd_cwnd * veno->basertt;
+		target_cwnd = (u64)tcp_snd_cwnd(tp) * veno->basertt;
 		target_cwnd <<= V_PARAM_SHIFT;
 		do_div(target_cwnd, rtt);
 
-		veno->diff = (tp->snd_cwnd << V_PARAM_SHIFT) - target_cwnd;
+		veno->diff = (tcp_snd_cwnd(tp) << V_PARAM_SHIFT) - target_cwnd;
 
 		if (tcp_in_slow_start(tp)) {
 			/* Slow start. */
@@ -164,15 +164,15 @@
 			/* In the "non-congestive state", increase cwnd
 			 * every rtt.
 			 */
-			tcp_cong_avoid_ai(tp, tp->snd_cwnd, acked);
+			tcp_cong_avoid_ai(tp, tcp_snd_cwnd(tp), acked);
 		} else {
 			/* In the "congestive state", increase cwnd
 			 * every other rtt.
 			 */
-			if (tp->snd_cwnd_cnt >= tp->snd_cwnd) {
+			if (tp->snd_cwnd_cnt >= tcp_snd_cwnd(tp)) {
 				if (veno->inc &&
-				    tp->snd_cwnd < tp->snd_cwnd_clamp) {
-					tp->snd_cwnd++;
+				    tcp_snd_cwnd(tp) < tp->snd_cwnd_clamp) {
+					tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) + 1);
 					veno->inc = 0;
 				} else
 					veno->inc = 1;
@@ -181,10 +181,10 @@
 				tp->snd_cwnd_cnt += acked;
 		}
 done:
-		if (tp->snd_cwnd < 2)
-			tp->snd_cwnd = 2;
-		else if (tp->snd_cwnd > tp->snd_cwnd_clamp)
-			tp->snd_cwnd = tp->snd_cwnd_clamp;
+		if (tcp_snd_cwnd(tp) < 2)
+			tcp_snd_cwnd_set(tp, 2);
+		else if (tcp_snd_cwnd(tp) > tp->snd_cwnd_clamp)
+			tcp_snd_cwnd_set(tp, tp->snd_cwnd_clamp);
 	}
 	/* Wipe the slate clean for the next rtt. */
 	/* veno->cntrtt = 0; */
@@ -199,10 +199,10 @@
 
 	if (veno->diff < beta)
 		/* in "non-congestive state", cut cwnd by 1/5 */
-		return max(tp->snd_cwnd * 4 / 5, 2U);
+		return max(tcp_snd_cwnd(tp) * 4 / 5, 2U);
 	else
 		/* in "congestive state", cut cwnd by 1/2 */
-		return max(tp->snd_cwnd >> 1U, 2U);
+		return max(tcp_snd_cwnd(tp) >> 1U, 2U);
 }
 
 static struct tcp_congestion_ops tcp_veno __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_westwood.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_westwood.c
@@ -244,7 +244,8 @@
 
 	switch (event) {
 	case CA_EVENT_COMPLETE_CWR:
-		tp->snd_cwnd = tp->snd_ssthresh = tcp_westwood_bw_rttmin(sk);
+		tp->snd_ssthresh = tcp_westwood_bw_rttmin(sk);
+		tcp_snd_cwnd_set(tp, tp->snd_ssthresh);
 		break;
 	case CA_EVENT_LOSS:
 		tp->snd_ssthresh = tcp_westwood_bw_rttmin(sk);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/tcp_yeah.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/tcp_yeah.c
@@ -71,11 +71,11 @@
 
 	if (!yeah->doing_reno_now) {
 		/* Scalable */
-		tcp_cong_avoid_ai(tp, min(tp->snd_cwnd, TCP_SCALABLE_AI_CNT),
+		tcp_cong_avoid_ai(tp, min(tcp_snd_cwnd(tp), TCP_SCALABLE_AI_CNT),
 				  acked);
 	} else {
 		/* Reno */
-		tcp_cong_avoid_ai(tp, tp->snd_cwnd, acked);
+		tcp_cong_avoid_ai(tp, tcp_snd_cwnd(tp), acked);
 	}
 
 	/* The key players are v_vegas.beg_snd_una and v_beg_snd_nxt.
@@ -130,7 +130,7 @@
 			/* Compute excess number of packets above bandwidth
 			 * Avoid doing full 64 bit divide.
 			 */
-			bw = tp->snd_cwnd;
+			bw = tcp_snd_cwnd(tp);
 			bw *= rtt - yeah->vegas.baseRTT;
 			do_div(bw, rtt);
 			queue = bw;
@@ -138,20 +138,20 @@
 			if (queue > TCP_YEAH_ALPHA ||
 			    rtt - yeah->vegas.baseRTT > (yeah->vegas.baseRTT / TCP_YEAH_PHY)) {
 				if (queue > TCP_YEAH_ALPHA &&
-				    tp->snd_cwnd > yeah->reno_count) {
+				    tcp_snd_cwnd(tp) > yeah->reno_count) {
 					u32 reduction = min(queue / TCP_YEAH_GAMMA ,
-							    tp->snd_cwnd >> TCP_YEAH_EPSILON);
+							    tcp_snd_cwnd(tp) >> TCP_YEAH_EPSILON);
 
-					tp->snd_cwnd -= reduction;
+					tcp_snd_cwnd_set(tp, tcp_snd_cwnd(tp) - reduction);
 
-					tp->snd_cwnd = max(tp->snd_cwnd,
-							   yeah->reno_count);
+					tcp_snd_cwnd_set(tp, max(tcp_snd_cwnd(tp),
+								 yeah->reno_count));
 
-					tp->snd_ssthresh = tp->snd_cwnd;
+					tp->snd_ssthresh = tcp_snd_cwnd(tp);
 				}
 
 				if (yeah->reno_count <= 2)
-					yeah->reno_count = max(tp->snd_cwnd>>1, 2U);
+					yeah->reno_count = max(tcp_snd_cwnd(tp)>>1, 2U);
 				else
 					yeah->reno_count++;
 
@@ -176,7 +176,7 @@
 		 */
 		yeah->vegas.beg_snd_una  = yeah->vegas.beg_snd_nxt;
 		yeah->vegas.beg_snd_nxt  = tp->snd_nxt;
-		yeah->vegas.beg_snd_cwnd = tp->snd_cwnd;
+		yeah->vegas.beg_snd_cwnd = tcp_snd_cwnd(tp);
 
 		/* Wipe the slate clean for the next RTT. */
 		yeah->vegas.cntRTT = 0;
@@ -193,16 +193,16 @@
 	if (yeah->doing_reno_now < TCP_YEAH_RHO) {
 		reduction = yeah->lastQ;
 
-		reduction = min(reduction, max(tp->snd_cwnd>>1, 2U));
+		reduction = min(reduction, max(tcp_snd_cwnd(tp)>>1, 2U));
 
-		reduction = max(reduction, tp->snd_cwnd >> TCP_YEAH_DELTA);
+		reduction = max(reduction, tcp_snd_cwnd(tp) >> TCP_YEAH_DELTA);
 	} else
-		reduction = max(tp->snd_cwnd>>1, 2U);
+		reduction = max(tcp_snd_cwnd(tp)>>1, 2U);
 
 	yeah->fast_count = 0;
 	yeah->reno_count = max(yeah->reno_count>>1, 2U);
 
-	return max_t(int, tp->snd_cwnd - reduction, 2);
+	return max_t(int, tcp_snd_cwnd(tp) - reduction, 2);
 }
 
 static struct tcp_congestion_ops tcp_yeah __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/udp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/udp.c
@@ -317,6 +317,8 @@
 			goto fail_unlock;
 		}
 
+		sock_set_flag(sk, SOCK_RCU_FREE);
+
 		sk_add_node_rcu(sk, &hslot->head);
 		hslot->count++;
 		sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
@@ -333,7 +335,7 @@
 		hslot2->count++;
 		spin_unlock(&hslot2->lock);
 	}
-	sock_set_flag(sk, SOCK_RCU_FREE);
+
 	error = 0;
 fail_unlock:
 	spin_unlock_bh(&hslot->lock);
@@ -398,9 +400,9 @@
 	return score;
 }
 
-static u32 udp_ehashfn(const struct net *net, const __be32 laddr,
-		       const __u16 lport, const __be32 faddr,
-		       const __be16 fport)
+INDIRECT_CALLABLE_SCOPE
+u32 udp_ehashfn(const struct net *net, const __be32 laddr, const __u16 lport,
+		const __be32 faddr, const __be16 fport)
 {
 	static u32 udp_ehash_secret __read_mostly;
 
@@ -410,22 +412,6 @@
 			      udp_ehash_secret + net_hash_mix(net));
 }
 
-static struct sock *lookup_reuseport(struct net *net, struct sock *sk,
-				     struct sk_buff *skb,
-				     __be32 saddr, __be16 sport,
-				     __be32 daddr, unsigned short hnum)
-{
-	struct sock *reuse_sk = NULL;
-	u32 hash;
-
-	if (sk->sk_reuseport && sk->sk_state != TCP_ESTABLISHED) {
-		hash = udp_ehashfn(net, daddr, hnum, saddr, sport);
-		reuse_sk = reuseport_select_sock(sk, hash, skb,
-						 sizeof(struct udphdr));
-	}
-	return reuse_sk;
-}
-
 /* called with rcu_read_lock() */
 static struct sock *udp4_lib_lookup2(struct net *net,
 				     __be32 saddr, __be16 sport,
@@ -436,21 +422,49 @@
 {
 	struct sock *sk, *result;
 	int score, badness;
+	bool need_rescore;
 
 	result = NULL;
 	badness = 0;
 	udp_portaddr_for_each_entry_rcu(sk, &hslot2->head) {
-		score = compute_score(sk, net, saddr, sport,
-				      daddr, hnum, dif, sdif);
+		need_rescore = false;
+rescore:
+		score = compute_score(need_rescore ? result : sk, net, saddr,
+				      sport, daddr, hnum, dif, sdif);
 		if (score > badness) {
-			result = lookup_reuseport(net, sk, skb,
-						  saddr, sport, daddr, hnum);
+			badness = score;
+
+			if (need_rescore)
+				continue;
+
+			if (sk->sk_state == TCP_ESTABLISHED) {
+				result = sk;
+				continue;
+			}
+
+			result = inet_lookup_reuseport(net, sk, skb, sizeof(struct udphdr),
+						       saddr, sport, daddr, hnum, udp_ehashfn);
+			if (!result) {
+				result = sk;
+				continue;
+			}
+
 			/* Fall back to scoring if group has connections */
-			if (result && !reuseport_has_conns(sk, false))
+			if (!reuseport_has_conns(sk))
 				return result;
 
-			result = result ? : sk;
-			badness = score;
+			/* Reuseport logic returned an error, keep original score. */
+			if (IS_ERR(result))
+				continue;
+
+			/* compute_score is too long of a function to be
+			 * inlined, and calling it again here yields
+			 * measureable overhead for some
+			 * workloads. Work around it by jumping
+			 * backwards to rescore 'result'.
+			 */
+			need_rescore = true;
+			goto rescore;
 		}
 	}
 	return result;
@@ -473,7 +487,8 @@
 	if (no_reuseport || IS_ERR_OR_NULL(sk))
 		return sk;
 
-	reuse_sk = lookup_reuseport(net, sk, skb, saddr, sport, daddr, hnum);
+	reuse_sk = inet_lookup_reuseport(net, sk, skb, sizeof(struct udphdr),
+					 saddr, sport, daddr, hnum, udp_ehashfn);
 	if (reuse_sk)
 		sk = reuse_sk;
 	return sk;
@@ -591,6 +606,13 @@
 }
 
 DEFINE_STATIC_KEY_FALSE(udp_encap_needed_key);
+EXPORT_SYMBOL(udp_encap_needed_key);
+
+#if IS_ENABLED(CONFIG_IPV6)
+DEFINE_STATIC_KEY_FALSE(udpv6_encap_needed_key);
+EXPORT_SYMBOL(udpv6_encap_needed_key);
+#endif
+
 void udp_encap_enable(void)
 {
 	static_branch_inc(&udp_encap_needed_key);
@@ -781,6 +803,8 @@
 	 */
 	if (tunnel) {
 		/* ...not for tunnels though: we don't have a sending socket */
+		if (udp_sk(sk)->encap_err_rcv)
+			udp_sk(sk)->encap_err_rcv(sk, skb, iph->ihl << 2);
 		goto out;
 	}
 	if (!inet->recverr) {
@@ -913,11 +937,11 @@
 		const int hlen = skb_network_header_len(skb) +
 				 sizeof(struct udphdr);
 
-		if (hlen + cork->gso_size > cork->fragsize) {
+		if (hlen + min(datalen, cork->gso_size) > cork->fragsize) {
 			kfree_skb(skb);
-			return -EINVAL;
+			return -EMSGSIZE;
 		}
-		if (skb->len > cork->gso_size * UDP_MAX_SEGMENTS) {
+		if (datalen > cork->gso_size * UDP_MAX_SEGMENTS) {
 			kfree_skb(skb);
 			return -EINVAL;
 		}
@@ -1120,16 +1144,17 @@
 
 	if (msg->msg_controllen) {
 		err = udp_cmsg_send(sk, msg, &ipc.gso_size);
-		if (err > 0)
+		if (err > 0) {
 			err = ip_cmsg_send(sk, msg, &ipc,
 					   sk->sk_family == AF_INET6);
+			connected = 0;
+		}
 		if (unlikely(err < 0)) {
 			kfree(ipc.opt);
 			return err;
 		}
 		if (ipc.opt)
 			free = 1;
-		connected = 0;
 	}
 	if (!ipc.opt) {
 		struct ip_options_rcu *inet_opt;
@@ -1594,7 +1619,7 @@
 }
 EXPORT_SYMBOL_GPL(__udp_enqueue_schedule_skb);
 
-void udp_destruct_sock(struct sock *sk)
+void udp_destruct_common(struct sock *sk)
 {
 	/* reclaim completely the forward allocated memory */
 	struct udp_sock *up = udp_sk(sk);
@@ -1607,10 +1632,14 @@
 		kfree_skb(skb);
 	}
 	udp_rmem_release(sk, total, 0, true);
+}
+EXPORT_SYMBOL_GPL(udp_destruct_common);
 
+static void udp_destruct_sock(struct sock *sk)
+{
+	udp_destruct_common(sk);
 	inet_sock_destruct(sk);
 }
-EXPORT_SYMBOL_GPL(udp_destruct_sock);
 
 int udp_init_sock(struct sock *sk)
 {
@@ -1618,7 +1647,6 @@
 	sk->sk_destruct = udp_destruct_sock;
 	return 0;
 }
-EXPORT_SYMBOL_GPL(udp_init_sock);
 
 void skb_consume_udp(struct sock *sk, struct sk_buff *skb, int len)
 {
@@ -1808,6 +1836,17 @@
 		skb = skb_recv_udp(sk, 0, 1, &err);
 		if (!skb)
 			return err;
+
+		if (udp_lib_checksum_complete(skb)) {
+			__UDP_INC_STATS(sock_net(sk), UDP_MIB_CSUMERRORS,
+					IS_UDPLITE(sk));
+			__UDP_INC_STATS(sock_net(sk), UDP_MIB_INERRORS,
+					IS_UDPLITE(sk));
+			atomic_inc(&sk->sk_drops);
+			kfree_skb(skb);
+			continue;
+		}
+
 		used = recv_actor(desc, skb, 0, skb->len);
 		if (used <= 0) {
 			if (!copied)
@@ -2240,7 +2279,7 @@
 	struct dst_entry *old;
 
 	if (dst_hold_safe(dst)) {
-		old = xchg(&sk->sk_rx_dst, dst);
+		old = xchg((__force struct dst_entry **)&sk->sk_rx_dst, dst);
 		dst_release(old);
 		return old != dst;
 	}
@@ -2400,6 +2439,9 @@
 	__be32 saddr, daddr;
 	struct net *net = dev_net(skb->dev);
 	bool refcounted;
+	int drop_reason;
+
+	drop_reason = SKB_DROP_REASON_NOT_SPECIFIED;
 
 	/*
 	 *  Validate the packet.
@@ -2430,7 +2472,7 @@
 		struct dst_entry *dst = skb_dst(skb);
 		int ret;
 
-		if (unlikely(sk->sk_rx_dst != dst))
+		if (unlikely(rcu_dereference(sk->sk_rx_dst) != dst))
 			udp_sk_rx_dst_set(sk, dst);
 
 		ret = udp_unicast_rcv_skb(sk, skb, uh);
@@ -2455,6 +2497,7 @@
 	if (udp_lib_checksum_complete(skb))
 		goto csum_error;
 
+	drop_reason = SKB_DROP_REASON_NO_SOCKET;
 	__UDP_INC_STATS(net, UDP_MIB_NOPORTS, proto == IPPROTO_UDPLITE);
 	icmp_send(skb, ICMP_DEST_UNREACH, ICMP_PORT_UNREACH, 0);
 
@@ -2462,10 +2505,11 @@
 	 * Hmm.  We got an UDP packet to a port to which we
 	 * don't wanna listen.  Ignore it.
 	 */
-	kfree_skb(skb);
+	kfree_skb_reason(skb, drop_reason);
 	return 0;
 
 short_packet:
+	drop_reason = SKB_DROP_REASON_PKT_TOO_SMALL;
 	net_dbg_ratelimited("UDP%s: short packet: From %pI4:%u %d/%d to %pI4:%u\n",
 			    proto == IPPROTO_UDPLITE ? "Lite" : "",
 			    &saddr, ntohs(uh->source),
@@ -2478,6 +2522,7 @@
 	 * RFC1122: OK.  Discards the bad packet silently (as far as
 	 * the network is concerned, anyway) as per 4.1.3.4 (MUST).
 	 */
+	drop_reason = SKB_DROP_REASON_UDP_CSUM;
 	net_dbg_ratelimited("UDP%s: bad checksum. From %pI4:%u to %pI4:%u ulen %d\n",
 			    proto == IPPROTO_UDPLITE ? "Lite" : "",
 			    &saddr, ntohs(uh->source), &daddr, ntohs(uh->dest),
@@ -2485,7 +2530,7 @@
 	__UDP_INC_STATS(net, UDP_MIB_CSUMERRORS, proto == IPPROTO_UDPLITE);
 drop:
 	__UDP_INC_STATS(net, UDP_MIB_INERRORS, proto == IPPROTO_UDPLITE);
-	kfree_skb(skb);
+	kfree_skb_reason(skb, drop_reason);
 	return 0;
 }
 
@@ -2537,8 +2582,7 @@
 	struct sock *sk;
 
 	udp_portaddr_for_each_entry_rcu(sk, &hslot2->head) {
-		if (INET_MATCH(sk, net, acookie, rmt_addr,
-			       loc_addr, ports, dif, sdif))
+		if (INET_MATCH(net, sk, acookie, ports, dif, sdif))
 			return sk;
 		/* Only check first socket in chain */
 		break;
@@ -2589,7 +2633,7 @@
 
 	skb->sk = sk;
 	skb->destructor = sock_efree;
-	dst = READ_ONCE(sk->sk_rx_dst);
+	dst = rcu_dereference(sk->sk_rx_dst);
 
 	if (dst)
 		dst = dst_check(dst, 0);
@@ -2680,10 +2724,12 @@
 		case UDP_ENCAP_ESPINUDP_NON_IKE:
 #if IS_ENABLED(CONFIG_IPV6)
 			if (sk->sk_family == AF_INET6)
-				up->encap_rcv = ipv6_stub->xfrm6_udp_encap_rcv;
+				WRITE_ONCE(up->encap_rcv,
+					   ipv6_stub->xfrm6_udp_encap_rcv);
 			else
 #endif
-				up->encap_rcv = xfrm4_udp_encap_rcv;
+				WRITE_ONCE(up->encap_rcv,
+					   xfrm4_udp_encap_rcv);
 #endif
 			fallthrough;
 		case UDP_ENCAP_L2TPINUDP:
@@ -2781,11 +2827,11 @@
 	if (get_user(len, optlen))
 		return -EFAULT;
 
-	len = min_t(unsigned int, len, sizeof(int));
-
 	if (len < 0)
 		return -EINVAL;
 
+	len = min_t(unsigned int, len, sizeof(int));
+
 	switch (optname) {
 	case UDP_CORK:
 		val = READ_ONCE(up->corkflag);
@@ -3065,7 +3111,7 @@
 {
 	seq_setwidth(seq, 127);
 	if (v == SEQ_START_TOKEN)
-		seq_puts(seq, "  sl  local_address rem_address   st tx_queue "
+		seq_puts(seq, "   sl  local_address rem_address   st tx_queue "
 			   "rx_queue tr tm->when retrnsmt   uid  timeout "
 			   "inode ref pointer drops");
 	else {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/udp_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/udp_bpf.c
@@ -69,6 +69,9 @@
 	if (unlikely(flags & MSG_ERRQUEUE))
 		return inet_recv_error(sk, msg, len, addr_len);
 
+	if (!len)
+		return 0;
+
 	psock = sk_psock_get(sk);
 	if (unlikely(!psock))
 		return sk_udp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/udp_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/udp_offload.c
@@ -272,24 +272,40 @@
 	__sum16 check;
 	__be16 newlen;
 
-	if (skb_shinfo(gso_skb)->gso_type & SKB_GSO_FRAGLIST)
-		return __udp_gso_segment_list(gso_skb, features, is_ipv6);
-
 	mss = skb_shinfo(gso_skb)->gso_size;
 	if (gso_skb->len <= sizeof(*uh) + mss)
 		return ERR_PTR(-EINVAL);
 
+	if (unlikely(skb_checksum_start(gso_skb) !=
+		     skb_transport_header(gso_skb) &&
+		     !(skb_shinfo(gso_skb)->gso_type & SKB_GSO_FRAGLIST)))
+		return ERR_PTR(-EINVAL);
+
+	if (skb_gso_ok(gso_skb, features | NETIF_F_GSO_ROBUST)) {
+		/* Packet is from an untrusted source, reset gso_segs. */
+		skb_shinfo(gso_skb)->gso_segs = DIV_ROUND_UP(gso_skb->len - sizeof(*uh),
+							     mss);
+		return NULL;
+	}
+
+	if (skb_shinfo(gso_skb)->gso_type & SKB_GSO_FRAGLIST)
+		return __udp_gso_segment_list(gso_skb, features, is_ipv6);
+
 	skb_pull(gso_skb, sizeof(*uh));
 
 	/* clear destructor to avoid skb_segment assigning it to tail */
 	copy_dtor = gso_skb->destructor == sock_wfree;
-	if (copy_dtor)
+	if (copy_dtor) {
 		gso_skb->destructor = NULL;
+		gso_skb->sk = NULL;
+	}
 
 	segs = skb_segment(gso_skb, features);
 	if (IS_ERR_OR_NULL(segs)) {
-		if (copy_dtor)
+		if (copy_dtor) {
 			gso_skb->destructor = sock_wfree;
+			gso_skb->sk = sk;
+		}
 		return segs;
 	}
 
@@ -434,6 +450,7 @@
 	struct sk_buff *p;
 	unsigned int ulen;
 	int ret = 0;
+	int flush;
 
 	/* requires non zero csum, for symmetry with GSO */
 	if (!uh->check) {
@@ -467,13 +484,22 @@
 			return p;
 		}
 
+		flush = NAPI_GRO_CB(p)->flush;
+
+		if (NAPI_GRO_CB(p)->flush_id != 1 ||
+		    NAPI_GRO_CB(p)->count != 1 ||
+		    !NAPI_GRO_CB(p)->is_atomic)
+			flush |= NAPI_GRO_CB(p)->flush_id;
+		else
+			NAPI_GRO_CB(p)->is_atomic = false;
+
 		/* Terminate the flow on len mismatch or if it grow "too much".
 		 * Under small packet flood GRO count could elsewhere grow a lot
 		 * leading to excessive truesize values.
 		 * On len mismatch merge the first packet shorter than gso_size,
 		 * otherwise complete the GRO packet.
 		 */
-		if (ulen > ntohs(uh2->len)) {
+		if (ulen > ntohs(uh2->len) || flush) {
 			pp = p;
 		} else {
 			if (NAPI_GRO_CB(skb)->is_flist) {
@@ -515,11 +541,19 @@
 	unsigned int off = skb_gro_offset(skb);
 	int flush = 1;
 
-	/* we can do L4 aggregation only if the packet can't land in a tunnel
-	 * otherwise we could corrupt the inner stream
+	/* We can do L4 aggregation only if the packet can't land in a tunnel
+	 * otherwise we could corrupt the inner stream. Detecting such packets
+	 * cannot be foolproof and the aggregation might still happen in some
+	 * cases. Such packets should be caught in udp_unexpected_gso later.
 	 */
 	NAPI_GRO_CB(skb)->is_flist = 0;
 	if (!sk || !udp_sk(sk)->gro_receive) {
+		/* If the packet was locally encapsulated in a UDP tunnel that
+		 * wasn't detected above, do not GRO.
+		 */
+		if (skb->encapsulation)
+			goto out;
+
 		if (skb->dev->features & NETIF_F_GRO_FRAGLIST)
 			NAPI_GRO_CB(skb)->is_flist = sk ? !udp_sk(sk)->gro_enabled : 1;
 
@@ -600,13 +634,11 @@
 					     inet_gro_compute_pseudo);
 skip:
 	NAPI_GRO_CB(skb)->is_ipv6 = 0;
-	rcu_read_lock();
 
 	if (static_branch_unlikely(&udp_encap_needed_key))
 		sk = udp4_gro_lookup_skb(skb, uh->source, uh->dest);
 
 	pp = udp_gro_receive(head, skb, uh, sk);
-	rcu_read_unlock();
 	return pp;
 
 flush:
@@ -641,7 +673,6 @@
 
 	uh->len = newlen;
 
-	rcu_read_lock();
 	sk = INDIRECT_CALL_INET(lookup, udp6_lib_lookup_skb,
 				udp4_lib_lookup_skb, skb, uh->source, uh->dest);
 	if (sk && udp_sk(sk)->gro_complete) {
@@ -662,7 +693,6 @@
 	} else {
 		err = udp_gro_complete_segment(skb);
 	}
-	rcu_read_unlock();
 
 	if (skb->remcsum_offload)
 		skb_shinfo(skb)->gso_type |= SKB_GSO_TUNNEL_REMCSUM;
@@ -683,13 +713,7 @@
 		skb_shinfo(skb)->gso_type |= (SKB_GSO_FRAGLIST|SKB_GSO_UDP_L4);
 		skb_shinfo(skb)->gso_segs = NAPI_GRO_CB(skb)->count;
 
-		if (skb->ip_summed == CHECKSUM_UNNECESSARY) {
-			if (skb->csum_level < SKB_MAX_CSUM_LEVEL)
-				skb->csum_level++;
-		} else {
-			skb->ip_summed = CHECKSUM_UNNECESSARY;
-			skb->csum_level = 0;
-		}
+		__skb_incr_checksum_unnecessary(skb);
 
 		return 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/udp_tunnel_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/udp_tunnel_core.c
@@ -75,6 +75,7 @@
 
 	udp_sk(sk)->encap_type = cfg->encap_type;
 	udp_sk(sk)->encap_rcv = cfg->encap_rcv;
+	udp_sk(sk)->encap_err_rcv = cfg->encap_err_rcv;
 	udp_sk(sk)->encap_err_lookup = cfg->encap_err_lookup;
 	udp_sk(sk)->encap_destroy = cfg->encap_destroy;
 	udp_sk(sk)->gro_receive = cfg->gro_receive;
@@ -178,6 +179,7 @@
 void udp_tunnel_sock_release(struct socket *sock)
 {
 	rcu_assign_sk_user_data(sock->sk, NULL);
+	synchronize_rcu();
 	kernel_sock_shutdown(sock, SHUT_RDWR);
 	sock_release(sock);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/udp_tunnel_nic.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/udp_tunnel_nic.c
@@ -846,7 +846,7 @@
 		list_for_each_entry(node, &info->shared->devices, list)
 			if (node->dev == dev)
 				break;
-		if (node->dev != dev)
+		if (list_entry_is_head(node, &info->shared->devices, list))
 			return;
 
 		list_del(&node->list);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/udplite.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/udplite.c
@@ -17,6 +17,14 @@
 struct udp_table 	udplite_table __read_mostly;
 EXPORT_SYMBOL(udplite_table);
 
+/* Designate sk as UDP-Lite socket */
+static int udplite_sk_init(struct sock *sk)
+{
+	udp_init_sock(sk);
+	udp_sk(sk)->pcflag = UDPLITE_BIT;
+	return 0;
+}
+
 static int udplite_rcv(struct sk_buff *skb)
 {
 	return __udp4_lib_rcv(skb, &udplite_table, IPPROTO_UDPLITE);
@@ -53,6 +61,8 @@
 	.get_port	   = udp_v4_get_port,
 	.memory_allocated  = &udp_memory_allocated,
 	.sysctl_mem	   = sysctl_udp_mem,
+	.sysctl_wmem_offset = offsetof(struct net, ipv4.sysctl_udp_wmem_min),
+	.sysctl_rmem_offset = offsetof(struct net, ipv4.sysctl_udp_rmem_min),
 	.obj_size	   = sizeof(struct udp_sock),
 	.h.udp_table	   = &udplite_table,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/xfrm4_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/xfrm4_input.c
@@ -61,7 +61,11 @@
 	ip_send_check(iph);
 
 	if (xo && (xo->flags & XFRM_GRO)) {
-		skb_mac_header_rebuild(skb);
+		/* The full l2 header needs to be preserved so that re-injecting the packet at l2
+		 * works correctly in the presence of vlan tags.
+		 */
+		skb_mac_header_rebuild_full(skb, xo->orig_mac_len);
+		skb_reset_network_header(skb);
 		skb_reset_transport_header(skb);
 		return 0;
 	}
@@ -164,6 +168,7 @@
 	kfree_skb(skb);
 	return 0;
 }
+EXPORT_SYMBOL(xfrm4_udp_encap_rcv);
 
 int xfrm4_rcv(struct sk_buff *skb)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/xfrm4_policy.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/xfrm4_policy.c
@@ -17,49 +17,43 @@
 #include <net/ip.h>
 #include <net/l3mdev.h>
 
-static struct dst_entry *__xfrm4_dst_lookup(struct net *net, struct flowi4 *fl4,
-					    int tos, int oif,
-					    const xfrm_address_t *saddr,
-					    const xfrm_address_t *daddr,
-					    u32 mark)
+static struct dst_entry *__xfrm4_dst_lookup(struct flowi4 *fl4,
+					    const struct xfrm_dst_lookup_params *params)
 {
 	struct rtable *rt;
 
 	memset(fl4, 0, sizeof(*fl4));
-	fl4->daddr = daddr->a4;
-	fl4->flowi4_tos = tos;
-	fl4->flowi4_oif = l3mdev_master_ifindex_by_index(net, oif);
-	fl4->flowi4_mark = mark;
-	if (saddr)
-		fl4->saddr = saddr->a4;
+	fl4->daddr = params->daddr->a4;
+	fl4->flowi4_tos = params->tos;
+	fl4->flowi4_l3mdev = l3mdev_master_ifindex_by_index(params->net,
+							    params->oif);
+	fl4->flowi4_mark = params->mark;
+	if (params->saddr)
+		fl4->saddr = params->saddr->a4;
+	fl4->flowi4_proto = params->ipproto;
+	fl4->uli = params->uli;
 
-	fl4->flowi4_flags = FLOWI_FLAG_SKIP_NH_OIF;
-
-	rt = __ip_route_output_key(net, fl4);
+	rt = __ip_route_output_key(params->net, fl4);
 	if (!IS_ERR(rt))
 		return &rt->dst;
 
 	return ERR_CAST(rt);
 }
 
-static struct dst_entry *xfrm4_dst_lookup(struct net *net, int tos, int oif,
-					  const xfrm_address_t *saddr,
-					  const xfrm_address_t *daddr,
-					  u32 mark)
+static struct dst_entry *xfrm4_dst_lookup(const struct xfrm_dst_lookup_params *params)
 {
 	struct flowi4 fl4;
 
-	return __xfrm4_dst_lookup(net, &fl4, tos, oif, saddr, daddr, mark);
+	return __xfrm4_dst_lookup(&fl4, params);
 }
 
-static int xfrm4_get_saddr(struct net *net, int oif,
-			   xfrm_address_t *saddr, xfrm_address_t *daddr,
-			   u32 mark)
+static int xfrm4_get_saddr(xfrm_address_t *saddr,
+			   const struct xfrm_dst_lookup_params *params)
 {
 	struct dst_entry *dst;
 	struct flowi4 fl4;
 
-	dst = __xfrm4_dst_lookup(net, &fl4, 0, oif, NULL, daddr, mark);
+	dst = __xfrm4_dst_lookup(&fl4, params);
 	if (IS_ERR(dst))
 		return -EHOSTUNREACH;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv4/xfrm4_protocol.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv4/xfrm4_protocol.c
@@ -304,4 +304,3 @@
 {
 	xfrm_input_register_afinfo(&xfrm4_input_afinfo);
 }
-EXPORT_SYMBOL(xfrm4_protocol_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/Kconfig
@@ -322,6 +322,7 @@
 	bool "IPv6: RPL Source Routing Header support"
 	depends on IPV6
 	select LWTUNNEL
+	select DST_CACHE
 	help
 	  Support for RFC6554 RPL Source Routing Header using the lightweight
 	  tunnels mechanism.
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/addrconf.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/addrconf.c
@@ -209,6 +209,7 @@
 	.ra_defrtr_metric	= IP6_RT_PRIO_USER,
 	.accept_ra_from_local	= 0,
 	.accept_ra_min_hop_limit= 1,
+	.accept_ra_min_lft	= 0,
 	.accept_ra_pinfo	= 1,
 #ifdef CONFIG_IPV6_ROUTER_PREF
 	.accept_ra_rtr_pref	= 1,
@@ -268,6 +269,7 @@
 	.ra_defrtr_metric	= IP6_RT_PRIO_USER,
 	.accept_ra_from_local	= 0,
 	.accept_ra_min_hop_limit= 1,
+	.accept_ra_min_lft	= 0,
 	.accept_ra_pinfo	= 1,
 #ifdef CONFIG_IPV6_ROUTER_PREF
 	.accept_ra_rtr_pref	= 1,
@@ -323,9 +325,8 @@
 static void addrconf_mod_rs_timer(struct inet6_dev *idev,
 				  unsigned long when)
 {
-	if (!timer_pending(&idev->rs_timer))
+	if (!mod_timer(&idev->rs_timer, jiffies + when))
 		in6_dev_hold(idev);
-	mod_timer(&idev->rs_timer, jiffies + when);
 }
 
 static void addrconf_mod_dad_work(struct inet6_ifaddr *ifp,
@@ -552,7 +553,7 @@
 #ifdef CONFIG_IPV6_MROUTE
 	if ((all || type == NETCONFA_MC_FORWARDING) &&
 	    nla_put_s32(skb, NETCONFA_MC_FORWARDING,
-			devconf->mc_forwarding) < 0)
+			atomic_read(&devconf->mc_forwarding)) < 0)
 		goto nla_put_failure;
 #endif
 	if ((all || type == NETCONFA_PROXY_NEIGH) &&
@@ -706,6 +707,22 @@
 	return err;
 }
 
+/* Combine dev_addr_genid and dev_base_seq to detect changes.
+ */
+static u32 inet6_base_seq(const struct net *net)
+{
+	u32 res = atomic_read(&net->ipv6.dev_addr_genid) +
+		  net->dev_base_seq;
+
+	/* Must not return 0 (see nl_dump_check_consistent()).
+	 * Chose a value far away from 0.
+	 */
+	if (!res)
+		res = 0x80000000;
+	return res;
+}
+
+
 static int inet6_netconf_dump_devconf(struct sk_buff *skb,
 				      struct netlink_callback *cb)
 {
@@ -739,8 +756,7 @@
 		idx = 0;
 		head = &net->dev_index_head[h];
 		rcu_read_lock();
-		cb->seq = atomic_read(&net->ipv6.dev_addr_genid) ^
-			  net->dev_base_seq;
+		cb->seq = inet6_base_seq(net);
 		hlist_for_each_entry_rcu(dev, head, index_hlist) {
 			if (idx < s_idx)
 				goto cont;
@@ -798,6 +814,7 @@
 {
 	struct net_device *dev;
 	struct inet6_ifaddr *ifa;
+	LIST_HEAD(tmp_addr_list);
 
 	if (!idev)
 		return;
@@ -816,14 +833,24 @@
 		}
 	}
 
+	read_lock_bh(&idev->lock);
 	list_for_each_entry(ifa, &idev->addr_list, if_list) {
 		if (ifa->flags&IFA_F_TENTATIVE)
 			continue;
+		list_add_tail(&ifa->if_list_aux, &tmp_addr_list);
+	}
+	read_unlock_bh(&idev->lock);
+
+	while (!list_empty(&tmp_addr_list)) {
+		ifa = list_first_entry(&tmp_addr_list,
+				       struct inet6_ifaddr, if_list_aux);
+		list_del(&ifa->if_list_aux);
 		if (idev->cnf.forwarding)
 			addrconf_join_anycast(ifa);
 		else
 			addrconf_leave_anycast(ifa);
 	}
+
 	inet6_netconf_notify_devconf(dev_net(dev), RTM_NEWNETCONF,
 				     NETCONFA_FORWARDING,
 				     dev->ifindex, &idev->cnf);
@@ -1100,10 +1127,6 @@
 		goto out;
 	}
 
-	if (net->ipv6.devconf_all->disable_policy ||
-	    idev->cnf.disable_policy)
-		f6i->dst_nopolicy = true;
-
 	neigh_parms_data_state_setall(idev->nd_parms);
 
 	ifa->addr = *cfg->pfx;
@@ -1362,7 +1385,7 @@
 	 * idev->desync_factor if it's larger
 	 */
 	cnf_temp_preferred_lft = READ_ONCE(idev->cnf.temp_prefered_lft);
-	max_desync_factor = min_t(__u32,
+	max_desync_factor = min_t(long,
 				  idev->cnf.max_desync_factor,
 				  cnf_temp_preferred_lft - regen_advance);
 
@@ -1808,7 +1831,8 @@
 							    master, &dst,
 							    scores, hiscore_idx);
 
-			if (scores[hiscore_idx].ifa)
+			if (scores[hiscore_idx].ifa &&
+			    scores[hiscore_idx].scopedist >= 0)
 				goto out;
 		}
 
@@ -1837,8 +1861,8 @@
 }
 EXPORT_SYMBOL(ipv6_dev_get_saddr);
 
-int __ipv6_get_lladdr(struct inet6_dev *idev, struct in6_addr *addr,
-		      u32 banned_flags)
+static int __ipv6_get_lladdr(struct inet6_dev *idev, struct in6_addr *addr,
+			      u32 banned_flags)
 {
 	struct inet6_ifaddr *ifp;
 	int err = -EADDRNOTAVAIL;
@@ -2031,9 +2055,10 @@
 		if (ipv6_addr_equal(&ifp->addr, addr)) {
 			if (!dev || ifp->idev->dev == dev ||
 			    !(ifp->scope&(IFA_LINK|IFA_HOST) || strict)) {
-				result = ifp;
-				in6_ifa_hold(ifp);
-				break;
+				if (in6_ifa_hold_safe(ifp)) {
+					result = ifp;
+					break;
+				}
 			}
 		}
 	}
@@ -2559,12 +2584,18 @@
 			ipv6_ifa_notify(0, ift);
 	}
 
-	if ((create || list_empty(&idev->tempaddr_list)) &&
-	    idev->cnf.use_tempaddr > 0) {
+	/* Also create a temporary address if it's enabled but no temporary
+	 * address currently exists.
+	 * However, we get called with valid_lft == 0, prefered_lft == 0, create == false
+	 * as part of cleanup (ie. deleting the mngtmpaddr).
+	 * We don't want that to result in creating a new temporary ip address.
+	 */
+	if (list_empty(&idev->tempaddr_list) && (valid_lft || prefered_lft))
+		create = true;
+
+	if (create && idev->cnf.use_tempaddr > 0) {
 		/* When a new public address is created as described
 		 * in [ADDRCONF], also create a new temporary address.
-		 * Also create a temporary address if it's enabled but
-		 * no temporary address currently exists.
 		 */
 		read_unlock_bh(&idev->lock);
 		ipv6_create_tempaddr(ifp, false);
@@ -2587,7 +2618,7 @@
 				 __u32 valid_lft, u32 prefered_lft)
 {
 	struct inet6_ifaddr *ifp = ipv6_get_ifaddr(net, addr, dev, 1);
-	int create = 0;
+	int create = 0, update_lft = 0;
 
 	if (!ifp && valid_lft) {
 		int max_addresses = in6_dev->cnf.max_addresses;
@@ -2631,19 +2662,32 @@
 		unsigned long now;
 		u32 stored_lft;
 
-		/* Update lifetime (RFC4862 5.5.3 e)
-		 * We deviate from RFC4862 by honoring all Valid Lifetimes to
-		 * improve the reaction of SLAAC to renumbering events
-		 * (draft-gont-6man-slaac-renum-06, Section 4.2)
-		 */
+		/* update lifetime (RFC2462 5.5.3 e) */
 		spin_lock_bh(&ifp->lock);
 		now = jiffies;
 		if (ifp->valid_lft > (now - ifp->tstamp) / HZ)
 			stored_lft = ifp->valid_lft - (now - ifp->tstamp) / HZ;
 		else
 			stored_lft = 0;
-
 		if (!create && stored_lft) {
+			const u32 minimum_lft = min_t(u32,
+				stored_lft, MIN_VALID_LIFETIME);
+			valid_lft = max(valid_lft, minimum_lft);
+
+			/* RFC4862 Section 5.5.3e:
+			 * "Note that the preferred lifetime of the
+			 *  corresponding address is always reset to
+			 *  the Preferred Lifetime in the received
+			 *  Prefix Information option, regardless of
+			 *  whether the valid lifetime is also reset or
+			 *  ignored."
+			 *
+			 * So we should always update prefered_lft here.
+			 */
+			update_lft = 1;
+		}
+
+		if (update_lft) {
 			ifp->valid_lft = valid_lft;
 			ifp->prefered_lft = prefered_lft;
 			ifp->tstamp = now;
@@ -2709,6 +2753,9 @@
 		return;
 	}
 
+	if (valid_lft != 0 && valid_lft < in6_dev->cnf.accept_ra_min_lft)
+		goto put;
+
 	/*
 	 *	Two things going on here:
 	 *	1) Add routes for on-link prefixes
@@ -3109,14 +3156,17 @@
 		offset = sizeof(struct in6_addr) - 4;
 	memcpy(&addr.s6_addr32[3], idev->dev->dev_addr + offset, 4);
 
-	if (idev->dev->flags&IFF_POINTOPOINT) {
-		addr.s6_addr32[0] = htonl(0xfe800000);
-		scope = IFA_LINK;
-		plen = 64;
-	} else {
+	if (!(idev->dev->flags & IFF_POINTOPOINT) && idev->dev->type == ARPHRD_SIT) {
 		scope = IPV6_ADDR_COMPATv4;
 		plen = 96;
 		pflags |= RTF_NONEXTHOP;
+	} else {
+		if (idev->cnf.addr_gen_mode == IN6_ADDR_GEN_MODE_NONE)
+			return;
+
+		addr.s6_addr32[0] = htonl(0xfe800000);
+		scope = IFA_LINK;
+		plen = 64;
 	}
 
 	if (addr.s6_addr32[3]) {
@@ -3424,6 +3474,30 @@
 }
 #endif
 
+static void addrconf_init_auto_addrs(struct net_device *dev)
+{
+	switch (dev->type) {
+#if IS_ENABLED(CONFIG_IPV6_SIT)
+	case ARPHRD_SIT:
+		addrconf_sit_config(dev);
+		break;
+#endif
+#if IS_ENABLED(CONFIG_NET_IPGRE) || IS_ENABLED(CONFIG_IPV6_GRE)
+	case ARPHRD_IP6GRE:
+	case ARPHRD_IPGRE:
+		addrconf_gre_config(dev);
+		break;
+#endif
+	case ARPHRD_LOOPBACK:
+		init_loopback(dev);
+		break;
+
+	default:
+		addrconf_dev_config(dev);
+		break;
+	}
+}
+
 static int fixup_permanent_addr(struct net *net,
 				struct inet6_dev *idev,
 				struct inet6_ifaddr *ifp)
@@ -3588,26 +3662,7 @@
 			run_pending = 1;
 		}
 
-		switch (dev->type) {
-#if IS_ENABLED(CONFIG_IPV6_SIT)
-		case ARPHRD_SIT:
-			addrconf_sit_config(dev);
-			break;
-#endif
-#if IS_ENABLED(CONFIG_NET_IPGRE) || IS_ENABLED(CONFIG_IPV6_GRE)
-		case ARPHRD_IP6GRE:
-		case ARPHRD_IPGRE:
-			addrconf_gre_config(dev);
-			break;
-#endif
-		case ARPHRD_LOOPBACK:
-			init_loopback(dev);
-			break;
-
-		default:
-			addrconf_dev_config(dev);
-			break;
-		}
+		addrconf_init_auto_addrs(dev);
 
 		if (!IS_ERR_OR_NULL(idev)) {
 			if (run_pending)
@@ -3712,8 +3767,10 @@
 	unsigned long event = unregister ? NETDEV_UNREGISTER : NETDEV_DOWN;
 	struct net *net = dev_net(dev);
 	struct inet6_dev *idev;
-	struct inet6_ifaddr *ifa, *tmp;
+	struct inet6_ifaddr *ifa;
+	LIST_HEAD(tmp_addr_list);
 	bool keep_addr = false;
+	bool was_ready;
 	int state, i;
 
 	ASSERT_RTNL();
@@ -3779,7 +3836,10 @@
 
 	addrconf_del_rs_timer(idev);
 
-	/* Step 2: clear flags for stateless addrconf */
+	/* Step 2: clear flags for stateless addrconf, repeated down
+	 *         detection
+	 */
+	was_ready = idev->if_flags & IF_READY;
 	if (!unregister)
 		idev->if_flags &= ~(IF_RS_SENT|IF_RA_RCVD|IF_READY);
 
@@ -3800,16 +3860,23 @@
 		write_lock_bh(&idev->lock);
 	}
 
-	list_for_each_entry_safe(ifa, tmp, &idev->addr_list, if_list) {
+	list_for_each_entry(ifa, &idev->addr_list, if_list)
+		list_add_tail(&ifa->if_list_aux, &tmp_addr_list);
+	write_unlock_bh(&idev->lock);
+
+	while (!list_empty(&tmp_addr_list)) {
 		struct fib6_info *rt = NULL;
 		bool keep;
 
+		ifa = list_first_entry(&tmp_addr_list,
+				       struct inet6_ifaddr, if_list_aux);
+		list_del(&ifa->if_list_aux);
+
 		addrconf_del_dad_work(ifa);
 
 		keep = keep_addr && (ifa->flags & IFA_F_PERMANENT) &&
 			!addr_is_local(&ifa->addr);
 
-		write_unlock_bh(&idev->lock);
 		spin_lock_bh(&ifa->lock);
 
 		if (keep) {
@@ -3840,20 +3907,19 @@
 			addrconf_leave_solict(ifa->idev, &ifa->addr);
 		}
 
-		write_lock_bh(&idev->lock);
 		if (!keep) {
+			write_lock_bh(&idev->lock);
 			list_del_rcu(&ifa->if_list);
+			write_unlock_bh(&idev->lock);
 			in6_ifa_put(ifa);
 		}
 	}
 
-	write_unlock_bh(&idev->lock);
-
 	/* Step 5: Discard anycast and multicast list */
 	if (unregister) {
 		ipv6_ac_destroy_dev(idev);
 		ipv6_mc_destroy_dev(idev);
-	} else {
+	} else if (was_ready) {
 		ipv6_mc_down(idev);
 	}
 
@@ -4066,7 +4132,7 @@
 			if (!ipv6_generate_eui64(addr.s6_addr + 8, idev->dev) &&
 			    ipv6_addr_equal(&ifp->addr, &addr)) {
 				/* DAD failed for link-local based on MAC */
-				idev->cnf.disable_ipv6 = 1;
+				WRITE_ONCE(idev->cnf.disable_ipv6, 1);
 
 				pr_info("%s: IPv6 being disabled!\n",
 					ifp->idev->dev->name);
@@ -4181,7 +4247,8 @@
 	send_rs = send_mld &&
 		  ipv6_accept_ra(ifp->idev) &&
 		  ifp->idev->cnf.rtr_solicits != 0 &&
-		  (dev->flags&IFF_LOOPBACK) == 0;
+		  (dev->flags & IFF_LOOPBACK) == 0 &&
+		  (dev->type != ARPHRD_TUNNEL);
 	read_unlock_bh(&ifp->idev->lock);
 
 	/* While dad is in progress mld report's source address is in6_addrany.
@@ -4980,6 +5047,7 @@
 	    nla_put_s32(skb, IFA_TARGET_NETNSID, args->netnsid))
 		goto error;
 
+	spin_lock_bh(&ifa->lock);
 	if (!((ifa->flags&IFA_F_PERMANENT) &&
 	      (ifa->prefered_lft == INFINITY_LIFE_TIME))) {
 		preferred = ifa->prefered_lft;
@@ -5001,6 +5069,7 @@
 		preferred = INFINITY_LIFE_TIME;
 		valid = INFINITY_LIFE_TIME;
 	}
+	spin_unlock_bh(&ifa->lock);
 
 	if (!ipv6_addr_any(&ifa->peer_addr)) {
 		if (nla_put_in6_addr(skb, IFA_LOCAL, &ifa->addr) < 0 ||
@@ -5129,9 +5198,9 @@
 		fillargs->event = RTM_GETMULTICAST;
 
 		/* multicast address */
-		for (ifmca = rcu_dereference(idev->mc_list);
+		for (ifmca = rtnl_dereference(idev->mc_list);
 		     ifmca;
-		     ifmca = rcu_dereference(ifmca->next), ip_idx++) {
+		     ifmca = rtnl_dereference(ifmca->next), ip_idx++) {
 			if (ip_idx < s_ip_idx)
 				continue;
 			err = inet6_fill_ifmcaddr(skb, ifmca, fillargs);
@@ -5264,7 +5333,7 @@
 	}
 
 	rcu_read_lock();
-	cb->seq = atomic_read(&tgt_net->ipv6.dev_addr_genid) ^ tgt_net->dev_base_seq;
+	cb->seq = inet6_base_seq(tgt_net);
 	for (h = s_h; h < NETDEV_HASHENTRIES; h++, s_idx = 0) {
 		idx = 0;
 		head = &tgt_net->dev_index_head[h];
@@ -5396,9 +5465,10 @@
 	}
 
 	addr = extract_addr(tb[IFA_ADDRESS], tb[IFA_LOCAL], &peer);
-	if (!addr)
-		return -EINVAL;
-
+	if (!addr) {
+		err = -EINVAL;
+		goto errout;
+	}
 	ifm = nlmsg_data(nlh);
 	if (ifm->ifa_index)
 		dev = dev_get_by_index(tgt_net, ifm->ifa_index);
@@ -5515,7 +5585,7 @@
 	array[DEVCONF_USE_OPTIMISTIC] = cnf->use_optimistic;
 #endif
 #ifdef CONFIG_IPV6_MROUTE
-	array[DEVCONF_MC_FORWARDING] = cnf->mc_forwarding;
+	array[DEVCONF_MC_FORWARDING] = atomic_read(&cnf->mc_forwarding);
 #endif
 	array[DEVCONF_DISABLE_IPV6] = cnf->disable_ipv6;
 	array[DEVCONF_ACCEPT_DAD] = cnf->accept_dad;
@@ -5542,6 +5612,7 @@
 	array[DEVCONF_IOAM6_ENABLED] = cnf->ioam6_enabled;
 	array[DEVCONF_IOAM6_ID] = cnf->ioam6_id;
 	array[DEVCONF_IOAM6_ID_WIDE] = cnf->ioam6_id_wide;
+	array[DEVCONF_ACCEPT_RA_MIN_LFT] = cnf->accept_ra_min_lft;
 }
 
 static inline size_t inet6_ifla6_size(void)
@@ -5618,6 +5689,27 @@
 	}
 }
 
+static int inet6_fill_ifla6_stats_attrs(struct sk_buff *skb,
+					struct inet6_dev *idev)
+{
+	struct nlattr *nla;
+
+	nla = nla_reserve(skb, IFLA_INET6_STATS, IPSTATS_MIB_MAX * sizeof(u64));
+	if (!nla)
+		goto nla_put_failure;
+	snmp6_fill_stats(nla_data(nla), idev, IFLA_INET6_STATS, nla_len(nla));
+
+	nla = nla_reserve(skb, IFLA_INET6_ICMP6STATS, ICMP6_MIB_MAX * sizeof(u64));
+	if (!nla)
+		goto nla_put_failure;
+	snmp6_fill_stats(nla_data(nla), idev, IFLA_INET6_ICMP6STATS, nla_len(nla));
+
+	return 0;
+
+nla_put_failure:
+	return -EMSGSIZE;
+}
+
 static int inet6_fill_ifla6_attrs(struct sk_buff *skb, struct inet6_dev *idev,
 				  u32 ext_filter_mask)
 {
@@ -5639,18 +5731,10 @@
 
 	/* XXX - MC not implemented */
 
-	if (ext_filter_mask & RTEXT_FILTER_SKIP_STATS)
-		return 0;
-
-	nla = nla_reserve(skb, IFLA_INET6_STATS, IPSTATS_MIB_MAX * sizeof(u64));
-	if (!nla)
-		goto nla_put_failure;
-	snmp6_fill_stats(nla_data(nla), idev, IFLA_INET6_STATS, nla_len(nla));
-
-	nla = nla_reserve(skb, IFLA_INET6_ICMP6STATS, ICMP6_MIB_MAX * sizeof(u64));
-	if (!nla)
-		goto nla_put_failure;
-	snmp6_fill_stats(nla_data(nla), idev, IFLA_INET6_ICMP6STATS, nla_len(nla));
+	if (!(ext_filter_mask & RTEXT_FILTER_SKIP_STATS)) {
+		if (inet6_fill_ifla6_stats_attrs(skb, idev) < 0)
+			goto nla_put_failure;
+	}
 
 	nla = nla_reserve(skb, IFLA_INET6_TOKEN, sizeof(struct in6_addr));
 	if (!nla)
@@ -6040,11 +6124,7 @@
 	pmsg->prefix_len = pinfo->prefix_len;
 	pmsg->prefix_type = pinfo->type;
 	pmsg->prefix_pad3 = 0;
-	pmsg->prefix_flags = 0;
-	if (pinfo->onlink)
-		pmsg->prefix_flags |= IF_PREFIX_ONLINK;
-	if (pinfo->autoconf)
-		pmsg->prefix_flags |= IF_PREFIX_AUTOCONF;
+	pmsg->prefix_flags = pinfo->flags;
 
 	if (nla_put(skb, PREFIX_ADDRESS, sizeof(pinfo->prefix), &pinfo->prefix))
 		goto nla_put_failure;
@@ -6211,7 +6291,8 @@
 		idev = __in6_dev_get(dev);
 		if (idev) {
 			int changed = (!idev->cnf.disable_ipv6) ^ (!newf);
-			idev->cnf.disable_ipv6 = newf;
+
+			WRITE_ONCE(idev->cnf.disable_ipv6, newf);
 			if (changed)
 				dev_disable_change(idev);
 		}
@@ -6228,7 +6309,7 @@
 
 	net = (struct net *)table->extra2;
 	old = *p;
-	*p = newf;
+	WRITE_ONCE(*p, newf);
 
 	if (p == &net->ipv6.devconf_dflt->disable_ipv6) {
 		rtnl_unlock();
@@ -6236,7 +6317,7 @@
 	}
 
 	if (p == &net->ipv6.devconf_all->disable_ipv6) {
-		net->ipv6.devconf_dflt->disable_ipv6 = newf;
+		WRITE_ONCE(net->ipv6.devconf_dflt->disable_ipv6, newf);
 		addrconf_disable_change(net, newf);
 	} else if ((!newf) ^ (!old))
 		dev_disable_change((struct inet6_dev *)table->extra1);
@@ -6348,7 +6429,7 @@
 
 			if (idev->cnf.addr_gen_mode != new_val) {
 				idev->cnf.addr_gen_mode = new_val;
-				addrconf_dev_config(idev->dev);
+				addrconf_init_auto_addrs(idev->dev);
 			}
 		} else if (&net->ipv6.devconf_all->addr_gen_mode == ctl->data) {
 			struct net_device *dev;
@@ -6359,7 +6440,7 @@
 				if (idev &&
 				    idev->cnf.addr_gen_mode != new_val) {
 					idev->cnf.addr_gen_mode = new_val;
-					addrconf_dev_config(idev->dev);
+					addrconf_init_auto_addrs(idev->dev);
 				}
 			}
 		}
@@ -6736,6 +6817,13 @@
 		.proc_handler	= proc_dointvec,
 	},
 	{
+		.procname	= "accept_ra_min_lft",
+		.data		= &ipv6_devconf.accept_ra_min_lft,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec,
+	},
+	{
 		.procname	= "accept_ra_pinfo",
 		.data		= &ipv6_devconf.accept_ra_pinfo,
 		.maxlen		= sizeof(int),
@@ -7091,9 +7179,8 @@
 	if (!dflt)
 		goto err_alloc_dflt;
 
-	if (IS_ENABLED(CONFIG_SYSCTL) &&
-	    !net_eq(net, &init_net)) {
-		switch (sysctl_devconf_inherit_init_net) {
+	if (!net_eq(net, &init_net)) {
+		switch (net_inherit_devconf()) {
 		case 1:  /* copy from init_net */
 			memcpy(all, init_net.ipv6.devconf_all,
 			       sizeof(ipv6_devconf));
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/addrconf_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/addrconf_core.c
@@ -220,19 +220,26 @@
 EXPORT_SYMBOL_GPL(ipv6_stub);
 
 /* IPv6 Wildcard Address and Loopback Address defined by RFC2553 */
-const struct in6_addr in6addr_loopback = IN6ADDR_LOOPBACK_INIT;
+const struct in6_addr in6addr_loopback __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_LOOPBACK_INIT;
 EXPORT_SYMBOL(in6addr_loopback);
-const struct in6_addr in6addr_any = IN6ADDR_ANY_INIT;
+const struct in6_addr in6addr_any __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_ANY_INIT;
 EXPORT_SYMBOL(in6addr_any);
-const struct in6_addr in6addr_linklocal_allnodes = IN6ADDR_LINKLOCAL_ALLNODES_INIT;
+const struct in6_addr in6addr_linklocal_allnodes __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_LINKLOCAL_ALLNODES_INIT;
 EXPORT_SYMBOL(in6addr_linklocal_allnodes);
-const struct in6_addr in6addr_linklocal_allrouters = IN6ADDR_LINKLOCAL_ALLROUTERS_INIT;
+const struct in6_addr in6addr_linklocal_allrouters __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_LINKLOCAL_ALLROUTERS_INIT;
 EXPORT_SYMBOL(in6addr_linklocal_allrouters);
-const struct in6_addr in6addr_interfacelocal_allnodes = IN6ADDR_INTERFACELOCAL_ALLNODES_INIT;
+const struct in6_addr in6addr_interfacelocal_allnodes __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_INTERFACELOCAL_ALLNODES_INIT;
 EXPORT_SYMBOL(in6addr_interfacelocal_allnodes);
-const struct in6_addr in6addr_interfacelocal_allrouters = IN6ADDR_INTERFACELOCAL_ALLROUTERS_INIT;
+const struct in6_addr in6addr_interfacelocal_allrouters __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_INTERFACELOCAL_ALLROUTERS_INIT;
 EXPORT_SYMBOL(in6addr_interfacelocal_allrouters);
-const struct in6_addr in6addr_sitelocal_allrouters = IN6ADDR_SITELOCAL_ALLROUTERS_INIT;
+const struct in6_addr in6addr_sitelocal_allrouters __aligned(BITS_PER_LONG/8)
+	= IN6ADDR_SITELOCAL_ALLROUTERS_INIT;
 EXPORT_SYMBOL(in6addr_sitelocal_allrouters);
 
 static void snmp6_free_dev(struct inet6_dev *idev)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/addrlabel.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/addrlabel.c
@@ -437,6 +437,7 @@
 {
 	struct ifaddrlblmsg *ifal = nlmsg_data(nlh);
 	ifal->ifal_family = AF_INET6;
+	ifal->__ifal_reserved = 0;
 	ifal->ifal_prefixlen = prefixlen;
 	ifal->ifal_flags = 0;
 	ifal->ifal_index = ifindex;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/af_inet6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/af_inet6.c
@@ -108,6 +108,13 @@
 	return (struct ipv6_pinfo *)(((u8 *)sk) + offset);
 }
 
+void inet6_sock_destruct(struct sock *sk)
+{
+	inet6_cleanup_sock(sk);
+	inet_sock_destruct(sk);
+}
+EXPORT_SYMBOL_GPL(inet6_sock_destruct);
+
 static int inet6_create(struct net *net, struct socket *sock, int protocol,
 			int kern)
 {
@@ -191,6 +198,9 @@
 	if (INET_PROTOSW_REUSE & answer_flags)
 		sk->sk_reuse = SK_CAN_REUSE;
 
+	if (INET_PROTOSW_ICSK & answer_flags)
+		inet_init_csk_locks(sk);
+
 	inet = inet_sk(sk);
 	inet->is_icsk = (INET_PROTOSW_ICSK & answer_flags) != 0;
 
@@ -200,7 +210,7 @@
 			inet->hdrincl = 1;
 	}
 
-	sk->sk_destruct		= inet_sock_destruct;
+	sk->sk_destruct		= inet6_sock_destruct;
 	sk->sk_family		= PF_INET6;
 	sk->sk_protocol		= protocol;
 
@@ -226,7 +236,7 @@
 	RCU_INIT_POINTER(inet->mc_list, NULL);
 	inet->rcv_tos	= 0;
 
-	if (net->ipv4.sysctl_ip_no_pmtu_disc)
+	if (READ_ONCE(net->ipv4.sysctl_ip_no_pmtu_disc))
 		inet->pmtudisc = IP_PMTUDISC_DONT;
 	else
 		inet->pmtudisc = IP_PMTUDISC_WANT;
@@ -248,31 +258,29 @@
 		 */
 		inet->inet_sport = htons(inet->inet_num);
 		err = sk->sk_prot->hash(sk);
-		if (err) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (err)
+			goto out_sk_release;
 	}
 	if (sk->sk_prot->init) {
 		err = sk->sk_prot->init(sk);
-		if (err) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (err)
+			goto out_sk_release;
 	}
 
 	if (!kern) {
 		err = BPF_CGROUP_RUN_PROG_INET_SOCK(sk);
-		if (err) {
-			sk_common_release(sk);
-			goto out;
-		}
+		if (err)
+			goto out_sk_release;
 	}
 out:
 	return err;
 out_rcu_unlock:
 	rcu_read_unlock();
 	goto out;
+out_sk_release:
+	sk_common_release(sk);
+	sock->sk = NULL;
+	goto out;
 }
 
 static int __inet6_bind(struct sock *sk, struct sockaddr *uaddr, int addr_len,
@@ -442,11 +450,14 @@
 {
 	struct sock *sk = sock->sk;
 	u32 flags = BIND_WITH_LOCK;
+	const struct proto *prot;
 	int err = 0;
 
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	prot = READ_ONCE(sk->sk_prot);
 	/* If the socket has its own bind function then use it. */
-	if (sk->sk_prot->bind)
-		return sk->sk_prot->bind(sk, uaddr, addr_len);
+	if (prot->bind)
+		return prot->bind(sk, uaddr, addr_len);
 
 	if (addr_len < SIN6_LEN_RFC2133)
 		return -EINVAL;
@@ -507,6 +518,12 @@
 }
 EXPORT_SYMBOL_GPL(inet6_destroy_sock);
 
+void inet6_cleanup_sock(struct sock *sk)
+{
+	inet6_destroy_sock(sk);
+}
+EXPORT_SYMBOL_GPL(inet6_cleanup_sock);
+
 /*
  *	This does both peername and sockname.
  */
@@ -521,31 +538,32 @@
 	sin->sin6_family = AF_INET6;
 	sin->sin6_flowinfo = 0;
 	sin->sin6_scope_id = 0;
+	lock_sock(sk);
 	if (peer) {
-		if (!inet->inet_dport)
-			return -ENOTCONN;
-		if (((1 << sk->sk_state) & (TCPF_CLOSE | TCPF_SYN_SENT)) &&
-		    peer == 1)
+		if (!inet->inet_dport ||
+		    (((1 << sk->sk_state) & (TCPF_CLOSE | TCPF_SYN_SENT)) &&
+		    peer == 1)) {
+			release_sock(sk);
 			return -ENOTCONN;
+		}
 		sin->sin6_port = inet->inet_dport;
 		sin->sin6_addr = sk->sk_v6_daddr;
 		if (np->sndflow)
 			sin->sin6_flowinfo = np->flow_label;
-		BPF_CGROUP_RUN_SA_PROG_LOCK(sk, (struct sockaddr *)sin,
-					    CGROUP_INET6_GETPEERNAME,
-					    NULL);
+		BPF_CGROUP_RUN_SA_PROG(sk, (struct sockaddr *)sin,
+				       CGROUP_INET6_GETPEERNAME);
 	} else {
 		if (ipv6_addr_any(&sk->sk_v6_rcv_saddr))
 			sin->sin6_addr = np->saddr;
 		else
 			sin->sin6_addr = sk->sk_v6_rcv_saddr;
 		sin->sin6_port = inet->inet_sport;
-		BPF_CGROUP_RUN_SA_PROG_LOCK(sk, (struct sockaddr *)sin,
-					    CGROUP_INET6_GETSOCKNAME,
-					    NULL);
+		BPF_CGROUP_RUN_SA_PROG(sk, (struct sockaddr *)sin,
+				       CGROUP_INET6_GETSOCKNAME);
 	}
 	sin->sin6_scope_id = ipv6_iface_scope_id(&sin->sin6_addr,
 						 sk->sk_bound_dev_if);
+	release_sock(sk);
 	return sizeof(*sin);
 }
 EXPORT_SYMBOL(inet6_getname);
@@ -555,6 +573,7 @@
 	void __user *argp = (void __user *)arg;
 	struct sock *sk = sock->sk;
 	struct net *net = sock_net(sk);
+	const struct proto *prot;
 
 	switch (cmd) {
 	case SIOCADDRT:
@@ -572,9 +591,11 @@
 	case SIOCSIFDSTADDR:
 		return addrconf_set_dstaddr(net, argp);
 	default:
-		if (!sk->sk_prot->ioctl)
+		/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+		prot = READ_ONCE(sk->sk_prot);
+		if (!prot->ioctl)
 			return -ENOIOCTLCMD;
-		return sk->sk_prot->ioctl(sk, cmd, arg);
+		return prot->ioctl(sk, cmd, arg);
 	}
 	/*NOTREACHED*/
 	return 0;
@@ -636,11 +657,14 @@
 int inet6_sendmsg(struct socket *sock, struct msghdr *msg, size_t size)
 {
 	struct sock *sk = sock->sk;
+	const struct proto *prot;
 
 	if (unlikely(inet_send_prepare(sk)))
 		return -EAGAIN;
 
-	return INDIRECT_CALL_2(sk->sk_prot->sendmsg, tcp_sendmsg, udpv6_sendmsg,
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	prot = READ_ONCE(sk->sk_prot);
+	return INDIRECT_CALL_2(prot->sendmsg, tcp_sendmsg, udpv6_sendmsg,
 			       sk, msg, size);
 }
 
@@ -650,13 +674,16 @@
 		  int flags)
 {
 	struct sock *sk = sock->sk;
+	const struct proto *prot;
 	int addr_len = 0;
 	int err;
 
 	if (likely(!(flags & MSG_ERRQUEUE)))
 		sock_rps_record_flow(sk);
 
-	err = INDIRECT_CALL_2(sk->sk_prot->recvmsg, tcp_recvmsg, udpv6_recvmsg,
+	/* IPV6_ADDRFORM can change sk->sk_prot under us. */
+	prot = READ_ONCE(sk->sk_prot);
+	err = INDIRECT_CALL_2(prot->recvmsg, tcp_recvmsg, udpv6_recvmsg,
 			      sk, msg, size, flags & MSG_DONTWAIT,
 			      flags & ~MSG_DONTWAIT, &addr_len);
 	if (err >= 0)
@@ -1025,6 +1052,7 @@
 	.ip6_mtu_from_fib6 = ip6_mtu_from_fib6,
 	.fib6_nh_init	   = fib6_nh_init,
 	.fib6_nh_release   = fib6_nh_release,
+	.fib6_nh_release_dsts = fib6_nh_release_dsts,
 	.fib6_update_sernum = fib6_update_sernum_stub,
 	.fib6_rt_update	   = fib6_rt_update,
 	.ip6_del_rt	   = ip6_del_rt,
@@ -1043,6 +1071,7 @@
 static const struct ipv6_bpf_stub ipv6_bpf_stub_impl = {
 	.inet6_bind = __inet6_bind,
 	.udp6_lib_lookup = __udp6_lib_lookup,
+	.ipv6_dev_get_saddr = ipv6_dev_get_saddr,
 };
 
 static int __init inet6_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/calipso.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/calipso.c
@@ -1075,8 +1075,13 @@
 	struct ipv6_opt_hdr *hop;
 	int opt_len, len, ret_val = -ENOMSG, offset;
 	unsigned char *opt;
-	struct ipv6_txoptions *txopts = txopt_get(inet6_sk(sk));
+	struct ipv6_pinfo *pinfo = inet6_sk(sk);
+	struct ipv6_txoptions *txopts;
 
+	if (!pinfo)
+		return -EAFNOSUPPORT;
+
+	txopts = txopt_get(pinfo);
 	if (!txopts || !txopts->hopopt)
 		goto done;
 
@@ -1128,8 +1133,13 @@
 {
 	int ret_val;
 	struct ipv6_opt_hdr *old, *new;
-	struct ipv6_txoptions *txopts = txopt_get(inet6_sk(sk));
+	struct ipv6_pinfo *pinfo = inet6_sk(sk);
+	struct ipv6_txoptions *txopts;
+
+	if (!pinfo)
+		return -EAFNOSUPPORT;
 
+	txopts = txopt_get(pinfo);
 	old = NULL;
 	if (txopts)
 		old = txopts->hopopt;
@@ -1156,8 +1166,13 @@
 static void calipso_sock_delattr(struct sock *sk)
 {
 	struct ipv6_opt_hdr *new_hop;
-	struct ipv6_txoptions *txopts = txopt_get(inet6_sk(sk));
+	struct ipv6_pinfo *pinfo = inet6_sk(sk);
+	struct ipv6_txoptions *txopts;
+
+	if (!pinfo)
+		return;
 
+	txopts = txopt_get(pinfo);
 	if (!txopts || !txopts->hopopt)
 		goto done;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/datagram.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/datagram.c
@@ -51,7 +51,7 @@
 	fl6->flowi6_mark = sk->sk_mark;
 	fl6->fl6_dport = inet->inet_dport;
 	fl6->fl6_sport = inet->inet_sport;
-	fl6->flowlabel = np->flow_label;
+	fl6->flowlabel = ip6_make_flowinfo(np->tclass, np->flow_label);
 	fl6->flowi6_uid = sk->sk_uid;
 
 	if (!fl6->flowi6_oif)
@@ -256,7 +256,7 @@
 		goto out;
 	}
 
-	reuseport_has_conns(sk, true);
+	reuseport_has_conns_set(sk);
 	sk->sk_state = TCP_ESTABLISHED;
 	sk_set_txhash(sk);
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/esp6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/esp6.c
@@ -255,8 +255,7 @@
 #else
 static int esp_output_tail_tcp(struct xfrm_state *x, struct sk_buff *skb)
 {
-	kfree_skb(skb);
-
+	WARN_ON(1);
 	return -EOPNOTSUPP;
 }
 #endif
@@ -491,6 +490,10 @@
 			return err;
 	}
 
+	if (ALIGN(tailen, L1_CACHE_BYTES) > PAGE_SIZE ||
+	    ALIGN(skb->data_len, L1_CACHE_BYTES) > PAGE_SIZE)
+		goto cow;
+
 	if (!skb_cloned(skb)) {
 		if (tailen <= skb_tailroom(skb)) {
 			nfrags = 1;
@@ -708,7 +711,7 @@
 		struct xfrm_dst *dst = (struct xfrm_dst *)skb_dst(skb);
 		u32 padto;
 
-		padto = min(x->tfcpad, __xfrm_state_mtu(x, dst->child_mtu_cached));
+		padto = min(x->tfcpad, xfrm_state_mtu(x, dst->child_mtu_cached));
 		if (skb->len < padto)
 			esp.tfclen = padto - skb->len;
 	}
@@ -772,7 +775,9 @@
 		skb->csum = csum_block_sub(skb->csum, csumdiff,
 					   skb->len - trimlen);
 	}
-	pskb_trim(skb, skb->len - trimlen);
+	ret = pskb_trim(skb, skb->len - trimlen);
+	if (unlikely(ret))
+		return ret;
 
 	ret = nexthdr[1];
 
@@ -808,6 +813,11 @@
 		struct tcphdr *th;
 
 		offset = ipv6_skip_exthdr(skb, offset, &nexthdr, &frag_off);
+		if (offset == -1) {
+			err = -EINVAL;
+			goto out;
+		}
+
 		uh = (void *)(skb->data + offset);
 		th = (void *)(skb->data + offset);
 		hdr_len += offset;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/esp6_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/esp6_offload.c
@@ -198,6 +198,9 @@
 			ipv6_skip_exthdr(skb, 0, &proto, &frag);
 	}
 
+	if (proto == IPPROTO_IPIP)
+		skb_shinfo(skb)->gso_type |= SKB_GSO_IPXIP6;
+
 	__skb_pull(skb, skb_transport_offset(skb));
 	ops = rcu_dereference(inet6_offloads[proto]);
 	if (likely(ops && ops->callbacks.gso_segment))
@@ -340,6 +343,9 @@
 			xo->seq.low += skb_shinfo(skb)->gso_segs;
 	}
 
+	if (xo->seq.low < seq)
+		xo->seq.hi++;
+
 	esp.seqno = cpu_to_be64(xo->seq.low + ((u64)xo->seq.hi << 32));
 
 	len = skb->len - sizeof(struct ipv6hdr);
@@ -366,6 +372,9 @@
 
 	secpath_reset(skb);
 
+	if (skb_needs_linearize(skb, skb->dev->features) &&
+	    __skb_linearize(skb))
+		return -ENOMEM;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/exthdrs.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/exthdrs.c
@@ -564,24 +564,6 @@
 		return -1;
 	}
 
-	if (skb_cloned(skb)) {
-		if (pskb_expand_head(skb, IPV6_RPL_SRH_WORST_SWAP_SIZE, 0,
-				     GFP_ATOMIC)) {
-			__IP6_INC_STATS(net, ip6_dst_idev(skb_dst(skb)),
-					IPSTATS_MIB_OUTDISCARDS);
-			kfree_skb(skb);
-			return -1;
-		}
-	} else {
-		err = skb_cow_head(skb, IPV6_RPL_SRH_WORST_SWAP_SIZE);
-		if (unlikely(err)) {
-			kfree_skb(skb);
-			return -1;
-		}
-	}
-
-	hdr = (struct ipv6_rpl_sr_hdr *)skb_transport_header(skb);
-
 	if (!pskb_may_pull(skb, ipv6_rpl_srh_size(n, hdr->cmpri,
 						  hdr->cmpre))) {
 		kfree_skb(skb);
@@ -627,6 +609,17 @@
 	skb_pull(skb, ((hdr->hdrlen + 1) << 3));
 	skb_postpull_rcsum(skb, oldhdr,
 			   sizeof(struct ipv6hdr) + ((hdr->hdrlen + 1) << 3));
+	if (unlikely(!hdr->segments_left)) {
+		if (pskb_expand_head(skb, sizeof(struct ipv6hdr) + ((chdr->hdrlen + 1) << 3), 0,
+				     GFP_ATOMIC)) {
+			__IP6_INC_STATS(net, ip6_dst_idev(skb_dst(skb)), IPSTATS_MIB_OUTDISCARDS);
+			kfree_skb(skb);
+			kfree(buf);
+			return -1;
+		}
+
+		oldhdr = ipv6_hdr(skb);
+	}
 	skb_push(skb, ((chdr->hdrlen + 1) << 3) + sizeof(struct ipv6hdr));
 	skb_reset_network_header(skb);
 	skb_mac_header_rebuild(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/exthdrs_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/exthdrs_core.c
@@ -143,6 +143,8 @@
 			optlen = 1;
 			break;
 		default:
+			if (len < 2)
+				goto bad;
 			optlen = nh[offset + 1] + 2;
 			if (optlen > len)
 				goto bad;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/fib6_rules.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/fib6_rules.c
@@ -232,8 +232,12 @@
 	rt = pol_lookup_func(lookup,
 			     net, table, flp6, arg->lookup_data, flags);
 	if (rt != net->ipv6.ip6_null_entry) {
+		struct inet6_dev *idev = ip6_dst_idev(&rt->dst);
+
+		if (!idev)
+			goto again;
 		err = fib6_rule_saddr(net, rule, flags, flp6,
-				      ip6_dst_idev(&rt->dst)->dev);
+				      idev->dev);
 
 		if (err == -EAGAIN)
 			goto again;
@@ -267,6 +271,7 @@
 }
 
 INDIRECT_CALLABLE_SCOPE bool fib6_rule_suppress(struct fib_rule *rule,
+						int flags,
 						struct fib_lookup_arg *arg)
 {
 	struct fib6_result *res = arg->result;
@@ -294,8 +299,7 @@
 	return false;
 
 suppress_route:
-	if (!(arg->flags & FIB_LOOKUP_NOREF))
-		ip6_rt_put(rt);
+	ip6_rt_put_flags(rt, flags);
 	return true;
 }
 
@@ -446,6 +450,11 @@
 	       + nla_total_size(16); /* src */
 }
 
+static void fib6_rule_flush_cache(struct fib_rules_ops *ops)
+{
+	rt_genid_bump_ipv6(ops->fro_net);
+}
+
 static const struct fib_rules_ops __net_initconst fib6_rules_ops_template = {
 	.family			= AF_INET6,
 	.rule_size		= sizeof(struct fib6_rule),
@@ -458,6 +467,7 @@
 	.compare		= fib6_rule_compare,
 	.fill			= fib6_rule_fill,
 	.nlmsg_payload		= fib6_rule_nlmsg_payload,
+	.flush_cache		= fib6_rule_flush_cache,
 	.nlgroup		= RTNLGRP_IPV6_RULE,
 	.policy			= fib6_rule_policy,
 	.owner			= THIS_MODULE,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/icmp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/icmp.c
@@ -57,6 +57,7 @@
 #include <net/protocol.h>
 #include <net/raw.h>
 #include <net/rawv6.h>
+#include <net/seg6.h>
 #include <net/transp_v6.h>
 #include <net/ip6_route.h>
 #include <net/addrconf.h>
@@ -429,7 +430,10 @@
 	if (unlikely(dev->ifindex == LOOPBACK_IFINDEX || netif_is_l3_master(skb->dev))) {
 		const struct rt6_info *rt6 = skb_rt6_info(skb);
 
-		if (rt6)
+		/* The destination could be an external IP in Ext Hdr (SRv6, RPL, etc.),
+		 * and ip6_null_entry could be set to skb if no route is found.
+		 */
+		if (rt6 && rt6->rt6i_idev)
 			dev = rt6->rt6i_idev->dev;
 	}
 
@@ -820,6 +824,7 @@
 
 void icmpv6_notify(struct sk_buff *skb, u8 type, u8 code, __be32 info)
 {
+	struct inet6_skb_parm *opt = IP6CB(skb);
 	const struct inet6_protocol *ipprot;
 	int inner_offset;
 	__be16 frag_off;
@@ -829,6 +834,8 @@
 	if (!pskb_may_pull(skb, sizeof(struct ipv6hdr)))
 		goto out;
 
+	seg6_icmp_srh(skb, opt);
+
 	nexthdr = ((struct ipv6hdr *)skb->data)->nexthdr;
 	if (ipv6_ext_hdr(nexthdr)) {
 		/* now skip over extension headers */
@@ -853,7 +860,7 @@
 
 	ipprot = rcu_dereference(inet6_protos[nexthdr]);
 	if (ipprot && ipprot->err_handler)
-		ipprot->err_handler(skb, NULL, type, code, inner_offset, info);
+		ipprot->err_handler(skb, opt, type, code, inner_offset, info);
 
 	raw6_icmp_error(skb, nexthdr, type, code, inner_offset, info);
 	return;
@@ -923,7 +930,7 @@
 		break;
 	case ICMPV6_EXT_ECHO_REQUEST:
 		if (!net->ipv6.sysctl.icmpv6_echo_ignore_all &&
-		    net->ipv4.sysctl_icmp_echo_enable_probe)
+		    READ_ONCE(net->ipv4.sysctl_icmp_echo_enable_probe))
 			icmpv6_echo_reply(skb);
 		break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ila/ila.h
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ila/ila.h
@@ -108,6 +108,7 @@
 void ila_lwt_fini(void);
 
 int ila_xlat_init_net(struct net *net);
+void ila_xlat_pre_exit_net(struct net *net);
 void ila_xlat_exit_net(struct net *net);
 
 int ila_xlat_nl_cmd_add_mapping(struct sk_buff *skb, struct genl_info *info);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ila/ila_lwt.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ila/ila_lwt.c
@@ -58,7 +58,9 @@
 		return orig_dst->lwtstate->orig_output(net, sk, skb);
 	}
 
+	local_bh_disable();
 	dst = dst_cache_get(&ilwt->dst_cache);
+	local_bh_enable();
 	if (unlikely(!dst)) {
 		struct ipv6hdr *ip6h = ipv6_hdr(skb);
 		struct flowi6 fl6;
@@ -86,10 +88,15 @@
 			goto drop;
 		}
 
-		if (ilwt->connected)
+		/* cache only if we don't create a dst reference loop */
+		if (ilwt->connected && orig_dst->lwtstate != dst->lwtstate) {
+			local_bh_disable();
 			dst_cache_set_ip6(&ilwt->dst_cache, dst, &fl6.saddr);
+			local_bh_enable();
+		}
 	}
 
+	skb_dst_drop(skb);
 	skb_dst_set(skb, dst);
 	return dst_output(net, sk, skb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ila/ila_main.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ila/ila_main.c
@@ -71,6 +71,11 @@
 	return err;
 }
 
+static __net_exit void ila_pre_exit_net(struct net *net)
+{
+	ila_xlat_pre_exit_net(net);
+}
+
 static __net_exit void ila_exit_net(struct net *net)
 {
 	ila_xlat_exit_net(net);
@@ -78,6 +83,7 @@
 
 static struct pernet_operations ila_net_ops = {
 	.init = ila_init_net,
+	.pre_exit = ila_pre_exit_net,
 	.exit = ila_exit_net,
 	.id   = &ila_net_id,
 	.size = sizeof(struct ila_net),
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ila/ila_xlat.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ila/ila_xlat.c
@@ -201,6 +201,8 @@
 	},
 };
 
+static DEFINE_MUTEX(ila_mutex);
+
 static int ila_add_mapping(struct net *net, struct ila_xlat_params *xp)
 {
 	struct ila_net *ilan = net_generic(net, ila_net_id);
@@ -208,16 +210,20 @@
 	spinlock_t *lock = ila_get_lock(ilan, xp->ip.locator_match);
 	int err = 0, order;
 
-	if (!ilan->xlat.hooks_registered) {
+	if (!READ_ONCE(ilan->xlat.hooks_registered)) {
 		/* We defer registering net hooks in the namespace until the
 		 * first mapping is added.
 		 */
-		err = nf_register_net_hooks(net, ila_nf_hook_ops,
-					    ARRAY_SIZE(ila_nf_hook_ops));
+		mutex_lock(&ila_mutex);
+		if (!ilan->xlat.hooks_registered) {
+			err = nf_register_net_hooks(net, ila_nf_hook_ops,
+						ARRAY_SIZE(ila_nf_hook_ops));
+			if (!err)
+				WRITE_ONCE(ilan->xlat.hooks_registered, true);
+		}
+		mutex_unlock(&ila_mutex);
 		if (err)
 			return err;
-
-		ilan->xlat.hooks_registered = true;
 	}
 
 	ila = kzalloc(sizeof(*ila), GFP_KERNEL);
@@ -477,6 +483,7 @@
 
 	rcu_read_lock();
 
+	ret = -ESRCH;
 	ila = ila_lookup_by_params(&xp, ilan);
 	if (ila) {
 		ret = ila_dump_info(ila,
@@ -615,6 +622,15 @@
 	return 0;
 }
 
+void ila_xlat_pre_exit_net(struct net *net)
+{
+	struct ila_net *ilan = net_generic(net, ila_net_id);
+
+	if (ilan->xlat.hooks_registered)
+		nf_unregister_net_hooks(net, ila_nf_hook_ops,
+					ARRAY_SIZE(ila_nf_hook_ops));
+}
+
 void ila_xlat_exit_net(struct net *net)
 {
 	struct ila_net *ilan = net_generic(net, ila_net_id);
@@ -622,10 +638,6 @@
 	rhashtable_free_and_destroy(&ilan->xlat.rhash_table, ila_free_cb, NULL);
 
 	free_bucket_spinlocks(ilan->xlat.locks);
-
-	if (ilan->xlat.hooks_registered)
-		nf_unregister_net_hooks(net, ila_nf_hook_ops,
-					ARRAY_SIZE(ila_nf_hook_ops));
 }
 
 static int ila_xlat_addr(struct sk_buff *skb, bool sir2ila)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/inet6_hashtables.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/inet6_hashtables.c
@@ -41,6 +41,7 @@
 	return __inet6_ehashfn(lhash, lport, fhash, fport,
 			       inet6_ehash_secret + net_hash_mix(net));
 }
+EXPORT_SYMBOL_GPL(inet6_ehashfn);
 
 /*
  * Sockets in TCP_CLOSE state are _always_ taken out of the hash, so
@@ -71,12 +72,12 @@
 	sk_nulls_for_each_rcu(sk, node, &head->chain) {
 		if (sk->sk_hash != hash)
 			continue;
-		if (!INET6_MATCH(sk, net, saddr, daddr, ports, dif, sdif))
+		if (!inet6_match(net, sk, saddr, daddr, ports, dif, sdif))
 			continue;
 		if (unlikely(!refcount_inc_not_zero(&sk->sk_refcnt)))
 			goto out;
 
-		if (unlikely(!INET6_MATCH(sk, net, saddr, daddr, ports, dif, sdif))) {
+		if (unlikely(!inet6_match(net, sk, saddr, daddr, ports, dif, sdif))) {
 			sock_gen_put(sk);
 			goto begin;
 		}
@@ -113,22 +114,27 @@
 	return score;
 }
 
-static inline struct sock *lookup_reuseport(struct net *net, struct sock *sk,
-					    struct sk_buff *skb, int doff,
-					    const struct in6_addr *saddr,
-					    __be16 sport,
-					    const struct in6_addr *daddr,
-					    unsigned short hnum)
+INDIRECT_CALLABLE_DECLARE(inet6_ehashfn_t udp6_ehashfn);
+
+struct sock *inet6_lookup_reuseport(struct net *net, struct sock *sk,
+				    struct sk_buff *skb, int doff,
+				    const struct in6_addr *saddr,
+				    __be16 sport,
+				    const struct in6_addr *daddr,
+				    unsigned short hnum,
+				    inet6_ehashfn_t *ehashfn)
 {
 	struct sock *reuse_sk = NULL;
 	u32 phash;
 
 	if (sk->sk_reuseport) {
-		phash = inet6_ehashfn(net, daddr, hnum, saddr, sport);
+		phash = INDIRECT_CALL_INET(ehashfn, udp6_ehashfn, inet6_ehashfn,
+					   net, daddr, hnum, saddr, sport);
 		reuse_sk = reuseport_select_sock(sk, phash, skb, doff);
 	}
 	return reuse_sk;
 }
+EXPORT_SYMBOL_GPL(inet6_lookup_reuseport);
 
 /* called with rcu_read_lock() */
 static struct sock *inet6_lhash2_lookup(struct net *net,
@@ -138,16 +144,15 @@
 		const __be16 sport, const struct in6_addr *daddr,
 		const unsigned short hnum, const int dif, const int sdif)
 {
-	struct inet_connection_sock *icsk;
 	struct sock *sk, *result = NULL;
+	struct hlist_nulls_node *node;
 	int score, hiscore = 0;
 
-	inet_lhash2_for_each_icsk_rcu(icsk, &ilb2->head) {
-		sk = (struct sock *)icsk;
+	sk_nulls_for_each_rcu(sk, node, &ilb2->nulls_head) {
 		score = compute_score(sk, net, hnum, daddr, dif, sdif);
 		if (score > hiscore) {
-			result = lookup_reuseport(net, sk, skb, doff,
-						  saddr, sport, daddr, hnum);
+			result = inet6_lookup_reuseport(net, sk, skb, doff,
+							saddr, sport, daddr, hnum, inet6_ehashfn);
 			if (result)
 				return result;
 
@@ -178,7 +183,8 @@
 	if (no_reuseport || IS_ERR_OR_NULL(sk))
 		return sk;
 
-	reuse_sk = lookup_reuseport(net, sk, skb, doff, saddr, sport, daddr, hnum);
+	reuse_sk = inet6_lookup_reuseport(net, sk, skb, doff,
+					  saddr, sport, daddr, hnum, inet6_ehashfn);
 	if (reuse_sk)
 		sk = reuse_sk;
 	return sk;
@@ -269,7 +275,7 @@
 		if (sk2->sk_hash != hash)
 			continue;
 
-		if (likely(INET6_MATCH(sk2, net, saddr, daddr, ports,
+		if (likely(inet6_match(net, sk2, saddr, daddr, ports,
 				       dif, sdif))) {
 			if (sk2->sk_state == TCP_TIME_WAIT) {
 				tw = inet_twsk(sk2);
@@ -308,7 +314,7 @@
 	return -EADDRNOTAVAIL;
 }
 
-static u32 inet6_sk_port_offset(const struct sock *sk)
+static u64 inet6_sk_port_offset(const struct sock *sk)
 {
 	const struct inet_sock *inet = inet_sk(sk);
 
@@ -320,7 +326,7 @@
 int inet6_hash_connect(struct inet_timewait_death_row *death_row,
 		       struct sock *sk)
 {
-	u32 port_offset = 0;
+	u64 port_offset = 0;
 
 	if (!inet_sk(sk)->inet_num)
 		port_offset = inet6_sk_port_offset(sk);
@@ -333,11 +339,8 @@
 {
 	int err = 0;
 
-	if (sk->sk_state != TCP_CLOSE) {
-		local_bh_disable();
+	if (sk->sk_state != TCP_CLOSE)
 		err = __inet_hash(sk, NULL);
-		local_bh_enable();
-	}
 
 	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_fib.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_fib.c
@@ -111,7 +111,7 @@
 	fn = rcu_dereference_protected(f6i->fib6_node,
 			lockdep_is_held(&f6i->fib6_table->tb6_lock));
 	if (fn)
-		fn->fn_sernum = fib6_new_sernum(net);
+		WRITE_ONCE(fn->fn_sernum, fib6_new_sernum(net));
 }
 
 /*
@@ -589,12 +589,13 @@
 		spin_unlock_bh(&table->tb6_lock);
 		if (res > 0) {
 			cb->args[4] = 1;
-			cb->args[5] = w->root->fn_sernum;
+			cb->args[5] = READ_ONCE(w->root->fn_sernum);
 		}
 	} else {
-		if (cb->args[5] != w->root->fn_sernum) {
+		int sernum = READ_ONCE(w->root->fn_sernum);
+		if (cb->args[5] != sernum) {
 			/* Begin at the root if the tree changed */
-			cb->args[5] = w->root->fn_sernum;
+			cb->args[5] = sernum;
 			w->state = FWS_INIT;
 			w->node = w->root;
 			w->skip = w->count;
@@ -644,19 +645,19 @@
 	if (!w) {
 		/* New dump:
 		 *
-		 * 1. hook callback destructor.
-		 */
-		cb->args[3] = (long)cb->done;
-		cb->done = fib6_dump_done;
-
-		/*
-		 * 2. allocate and initialize walker.
+		 * 1. allocate and initialize walker.
 		 */
 		w = kzalloc(sizeof(*w), GFP_ATOMIC);
 		if (!w)
 			return -ENOMEM;
 		w->func = fib6_dump_node;
 		cb->args[2] = (long)w;
+
+		/* 2. hook callback destructor.
+		 */
+		cb->args[3] = (long)cb->done;
+		cb->done = fib6_dump_done;
+
 	}
 
 	arg.skb = skb;
@@ -960,6 +961,7 @@
 	if (!fib6_nh->rt6i_pcpu)
 		return;
 
+	rcu_read_lock();
 	/* release the reference to this fib entry from
 	 * all of its cached pcpu routes
 	 */
@@ -968,7 +970,9 @@
 		struct rt6_info *pcpu_rt;
 
 		ppcpu_rt = per_cpu_ptr(fib6_nh->rt6i_pcpu, cpu);
-		pcpu_rt = *ppcpu_rt;
+
+		/* Paired with xchg() in rt6_get_pcpu_route() */
+		pcpu_rt = READ_ONCE(*ppcpu_rt);
 
 		/* only dropping the 'from' reference if the cached route
 		 * is using 'match'. The cached pcpu_rt->from only changes
@@ -982,6 +986,7 @@
 			fib6_info_release(from);
 		}
 	}
+	rcu_read_unlock();
 }
 
 struct fib6_nh_pcpu_arg {
@@ -1344,7 +1349,7 @@
 	/* paired with smp_rmb() in fib6_get_cookie_safe() */
 	smp_wmb();
 	while (fn) {
-		fn->fn_sernum = sernum;
+		WRITE_ONCE(fn->fn_sernum, sernum);
 		fn = rcu_dereference_protected(fn->parent,
 				lockdep_is_held(&rt->fib6_table->tb6_lock));
 	}
@@ -1374,7 +1379,10 @@
 	     struct nl_info *info, struct netlink_ext_ack *extack)
 {
 	struct fib6_table *table = rt->fib6_table;
-	struct fib6_node *fn, *pn = NULL;
+	struct fib6_node *fn;
+#ifdef CONFIG_IPV6_SUBTREES
+	struct fib6_node *pn = NULL;
+#endif
 	int err = -ENOMEM;
 	int allow_create = 1;
 	int replace_required = 0;
@@ -1398,9 +1406,9 @@
 		goto out;
 	}
 
+#ifdef CONFIG_IPV6_SUBTREES
 	pn = fn;
 
-#ifdef CONFIG_IPV6_SUBTREES
 	if (rt->fib6_src.plen) {
 		struct fib6_node *sn;
 
@@ -1500,13 +1508,9 @@
 			if (!pn_leaf && !(pn->fn_flags & RTN_RTINFO)) {
 				pn_leaf = fib6_find_prefix(info->nl_net, table,
 							   pn);
-#if RT6_DEBUG >= 2
-				if (!pn_leaf) {
-					WARN_ON(!pn_leaf);
+				if (!pn_leaf)
 					pn_leaf =
 					    info->nl_net->ipv6.fib6_null_entry;
-				}
-#endif
 				fib6_info_hold(pn_leaf);
 				rcu_assign_pointer(pn->leaf, pn_leaf);
 			}
@@ -2173,8 +2177,8 @@
 	};
 
 	if (c->sernum != FIB6_NO_SERNUM_CHANGE &&
-	    w->node->fn_sernum != c->sernum)
-		w->node->fn_sernum = c->sernum;
+	    READ_ONCE(w->node->fn_sernum) != c->sernum)
+		WRITE_ONCE(w->node->fn_sernum, c->sernum);
 
 	if (!c->func) {
 		WARN_ON_ONCE(c->sernum == FIB6_NO_SERNUM_CHANGE);
@@ -2542,7 +2546,7 @@
 	iter->w.state = FWS_INIT;
 	iter->w.node = iter->w.root;
 	iter->w.args = iter;
-	iter->sernum = iter->w.root->fn_sernum;
+	iter->sernum = READ_ONCE(iter->w.root->fn_sernum);
 	INIT_LIST_HEAD(&iter->w.lh);
 	fib6_walker_link(net, &iter->w);
 }
@@ -2570,8 +2574,10 @@
 
 static void ipv6_route_check_sernum(struct ipv6_route_iter *iter)
 {
-	if (iter->sernum != iter->w.root->fn_sernum) {
-		iter->sernum = iter->w.root->fn_sernum;
+	int sernum = READ_ONCE(iter->w.root->fn_sernum);
+
+	if (iter->sernum != sernum) {
+		iter->sernum = sernum;
 		iter->w.state = FWS_INIT;
 		iter->w.node = iter->w.root;
 		WARN_ON(iter->w.skip);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_flowlabel.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_flowlabel.c
@@ -450,8 +450,10 @@
 		err = -EINVAL;
 		goto done;
 	}
-	if (fl_shared_exclusive(fl) || fl->opt)
+	if (fl_shared_exclusive(fl) || fl->opt) {
+		WRITE_ONCE(sock_net(sk)->ipv6.flowlabel_has_excl, 1);
 		static_branch_deferred_inc(&ipv6_flowlabel_exclusive);
+	}
 	return fl;
 
 done:
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_gre.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_gre.c
@@ -533,6 +533,9 @@
 	struct ip6_tnl *tunnel;
 	u8 ver;
 
+	if (unlikely(!pskb_may_pull(skb, sizeof(*ershdr))))
+		return PACKET_REJECT;
+
 	ipv6h = ipv6_hdr(skb);
 	ershdr = (struct erspan_base_hdr *)skb->data;
 	ver = ershdr->ver;
@@ -724,6 +727,7 @@
 {
 	struct ip6_tnl *tunnel = netdev_priv(dev);
 	__be16 protocol;
+	__be16 flags;
 
 	if (dev->type == ARPHRD_ETHER)
 		IPCB(skb)->flags = 0;
@@ -733,16 +737,13 @@
 	else
 		fl6->daddr = tunnel->parms.raddr;
 
-	if (skb_cow_head(skb, dev->needed_headroom ?: tunnel->hlen))
-		return -ENOMEM;
-
 	/* Push GRE header. */
 	protocol = (dev->type == ARPHRD_ETHER) ? htons(ETH_P_TEB) : proto;
 
 	if (tunnel->parms.collect_md) {
 		struct ip_tunnel_info *tun_info;
 		const struct ip_tunnel_key *key;
-		__be16 flags;
+		int tun_hlen;
 
 		tun_info = skb_tunnel_info_txcheck(skb);
 		if (IS_ERR(tun_info) ||
@@ -755,25 +756,32 @@
 		fl6->daddr = key->u.ipv6.dst;
 		fl6->flowlabel = key->label;
 		fl6->flowi6_uid = sock_net_uid(dev_net(dev), NULL);
+		fl6->fl6_gre_key = tunnel_id_to_key32(key->tun_id);
 
 		dsfield = key->tos;
 		flags = key->tun_flags &
 			(TUNNEL_CSUM | TUNNEL_KEY | TUNNEL_SEQ);
-		tunnel->tun_hlen = gre_calc_hlen(flags);
+		tun_hlen = gre_calc_hlen(flags);
+
+		if (skb_cow_head(skb, dev->needed_headroom ?: tun_hlen + tunnel->encap_hlen))
+			return -ENOMEM;
 
-		gre_build_header(skb, tunnel->tun_hlen,
+		gre_build_header(skb, tun_hlen,
 				 flags, protocol,
 				 tunnel_id_to_key32(tun_info->key.tun_id),
-				 (flags & TUNNEL_SEQ) ? htonl(tunnel->o_seqno++)
+				 (flags & TUNNEL_SEQ) ? htonl(atomic_fetch_inc(&tunnel->o_seqno))
 						      : 0);
 
 	} else {
-		if (tunnel->parms.o_flags & TUNNEL_SEQ)
-			tunnel->o_seqno++;
+		if (skb_cow_head(skb, dev->needed_headroom ?: tunnel->hlen))
+			return -ENOMEM;
 
-		gre_build_header(skb, tunnel->tun_hlen, tunnel->parms.o_flags,
+		flags = tunnel->parms.o_flags;
+
+		gre_build_header(skb, tunnel->tun_hlen, flags,
 				 protocol, tunnel->parms.o_key,
-				 htonl(tunnel->o_seqno));
+				 (flags & TUNNEL_SEQ) ? htonl(atomic_fetch_inc(&tunnel->o_seqno))
+						      : 0);
 	}
 
 	return ip6_tnl_xmit(skb, dev, dsfield, fl6, encap_limit, pmtu,
@@ -939,7 +947,6 @@
 	__be16 proto;
 	__u32 mtu;
 	int nhoff;
-	int thoff;
 
 	if (!pskb_inet_may_pull(skb))
 		goto tx_err;
@@ -951,19 +958,26 @@
 		goto tx_err;
 
 	if (skb->len > dev->mtu + dev->hard_header_len) {
-		pskb_trim(skb, dev->mtu + dev->hard_header_len);
+		if (pskb_trim(skb, dev->mtu + dev->hard_header_len))
+			goto tx_err;
 		truncate = true;
 	}
 
-	nhoff = skb_network_header(skb) - skb_mac_header(skb);
+	nhoff = skb_network_offset(skb);
 	if (skb->protocol == htons(ETH_P_IP) &&
 	    (ntohs(ip_hdr(skb)->tot_len) > skb->len - nhoff))
 		truncate = true;
 
-	thoff = skb_transport_header(skb) - skb_mac_header(skb);
-	if (skb->protocol == htons(ETH_P_IPV6) &&
-	    (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff))
-		truncate = true;
+	if (skb->protocol == htons(ETH_P_IPV6)) {
+		int thoff;
+
+		if (skb_transport_header_was_set(skb))
+			thoff = skb_transport_offset(skb);
+		else
+			thoff = nhoff + sizeof(struct ipv6hdr);
+		if (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff)
+			truncate = true;
+	}
 
 	if (skb_cow_head(skb, dev->needed_headroom ?: t->hlen))
 		goto tx_err;
@@ -990,6 +1004,7 @@
 		fl6.daddr = key->u.ipv6.dst;
 		fl6.flowlabel = key->label;
 		fl6.flowi6_uid = sock_net_uid(dev_net(dev), NULL);
+		fl6.fl6_gre_key = tunnel_id_to_key32(key->tun_id);
 
 		dsfield = key->tos;
 		if (!(tun_info->key.tun_flags & TUNNEL_ERSPAN_OPT))
@@ -1004,12 +1019,14 @@
 					    ntohl(tun_id),
 					    ntohl(md->u.index), truncate,
 					    false);
+			proto = htons(ETH_P_ERSPAN);
 		} else if (md->version == 2) {
 			erspan_build_header_v2(skb,
 					       ntohl(tun_id),
 					       md->u.md2.dir,
 					       get_hwid(&md->u.md2),
 					       truncate, false);
+			proto = htons(ETH_P_ERSPAN2);
 		} else {
 			goto tx_err;
 		}
@@ -1032,25 +1049,26 @@
 			break;
 		}
 
-		if (t->parms.erspan_ver == 1)
+		if (t->parms.erspan_ver == 1) {
 			erspan_build_header(skb, ntohl(t->parms.o_key),
 					    t->parms.index,
 					    truncate, false);
-		else if (t->parms.erspan_ver == 2)
+			proto = htons(ETH_P_ERSPAN);
+		} else if (t->parms.erspan_ver == 2) {
 			erspan_build_header_v2(skb, ntohl(t->parms.o_key),
 					       t->parms.dir,
 					       t->parms.hwid,
 					       truncate, false);
-		else
+			proto = htons(ETH_P_ERSPAN2);
+		} else {
 			goto tx_err;
+		}
 
 		fl6.daddr = t->parms.raddr;
 	}
 
 	/* Push GRE header. */
-	proto = (t->parms.erspan_ver == 1) ? htons(ETH_P_ERSPAN)
-					   : htons(ETH_P_ERSPAN2);
-	gre_build_header(skb, 8, TUNNEL_SEQ, proto, 0, htonl(t->o_seqno++));
+	gre_build_header(skb, 8, TUNNEL_SEQ, proto, 0, htonl(atomic_fetch_inc(&t->o_seqno)));
 
 	/* TooBig packet may have updated dst->dev's mtu */
 	if (!t->parms.collect_md && dst && dst_mtu(dst) > dst->dev->mtu)
@@ -1098,6 +1116,7 @@
 	fl6->flowi6_oif = p->link;
 	fl6->flowlabel = 0;
 	fl6->flowi6_proto = IPPROTO_GRE;
+	fl6->fl6_gre_key = t->parms.o_key;
 
 	if (!(p->flags&IP6_TNL_F_USE_ORIG_TCLASS))
 		fl6->flowlabel |= IPV6_TCLASS_MASK & p->flowinfo;
@@ -1141,14 +1160,16 @@
 				dev->needed_headroom = dst_len;
 
 			if (set_mtu) {
-				dev->mtu = rt->dst.dev->mtu - t_hlen;
+				int mtu = rt->dst.dev->mtu - t_hlen;
+
 				if (!(t->parms.flags & IP6_TNL_F_IGN_ENCAP_LIMIT))
-					dev->mtu -= 8;
+					mtu -= 8;
 				if (dev->type == ARPHRD_ETHER)
-					dev->mtu -= ETH_HLEN;
+					mtu -= ETH_HLEN;
 
-				if (dev->mtu < IPV6_MIN_MTU)
-					dev->mtu = IPV6_MIN_MTU;
+				if (mtu < IPV6_MIN_MTU)
+					mtu = IPV6_MIN_MTU;
+				WRITE_ONCE(dev->mtu, mtu);
 			}
 		}
 		ip6_rt_put(rt);
@@ -1544,7 +1565,7 @@
 static struct inet6_protocol ip6gre_protocol __read_mostly = {
 	.handler     = gre_rcv,
 	.err_handler = ip6gre_err,
-	.flags       = INET6_PROTO_NOPOLICY|INET6_PROTO_FINAL,
+	.flags       = INET6_PROTO_FINAL,
 };
 
 static void ip6gre_destroy_tunnels(struct net *net, struct list_head *head)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_input.c
@@ -45,20 +45,23 @@
 #include <net/inet_ecn.h>
 #include <net/dst_metadata.h>
 
-INDIRECT_CALLABLE_DECLARE(void tcp_v6_early_demux(struct sk_buff *));
 static void ip6_rcv_finish_core(struct net *net, struct sock *sk,
 				struct sk_buff *skb)
 {
-	void (*edemux)(struct sk_buff *skb);
-
-	if (net->ipv4.sysctl_ip_early_demux && !skb_dst(skb) && skb->sk == NULL) {
-		const struct inet6_protocol *ipprot;
-
-		ipprot = rcu_dereference(inet6_protos[ipv6_hdr(skb)->nexthdr]);
-		if (ipprot && (edemux = READ_ONCE(ipprot->early_demux)))
-			INDIRECT_CALL_2(edemux, tcp_v6_early_demux,
-					udp_v6_early_demux, skb);
+	if (READ_ONCE(net->ipv4.sysctl_ip_early_demux) &&
+	    !skb_dst(skb) && !skb->sk) {
+		switch (ipv6_hdr(skb)->nexthdr) {
+		case IPPROTO_TCP:
+			if (READ_ONCE(net->ipv4.sysctl_tcp_early_demux))
+				tcp_v6_early_demux(skb);
+			break;
+		case IPPROTO_UDP:
+			if (READ_ONCE(net->ipv4.sysctl_udp_early_demux))
+				udp_v6_early_demux(skb);
+			break;
+		}
 	}
+
 	if (!skb_valid_dst(skb))
 		ip6_route_input(skb);
 }
@@ -161,7 +164,7 @@
 	__IP6_UPD_PO_STATS(net, idev, IPSTATS_MIB_IN, skb->len);
 
 	if ((skb = skb_share_check(skb, GFP_ATOMIC)) == NULL ||
-	    !idev || unlikely(idev->cnf.disable_ipv6)) {
+	    !idev || unlikely(READ_ONCE(idev->cnf.disable_ipv6))) {
 		__IP6_INC_STATS(net, idev, IPSTATS_MIB_INDISCARDS);
 		goto drop;
 	}
@@ -508,7 +511,7 @@
 	/*
 	 *      IPv6 multicast router mode is now supported ;)
 	 */
-	if (dev_net(skb->dev)->ipv6.devconf_all->mc_forwarding &&
+	if (atomic_read(&dev_net(skb->dev)->ipv6.devconf_all->mc_forwarding) &&
 	    !(ipv6_addr_type(&hdr->daddr) &
 	      (IPV6_ADDR_LOOPBACK|IPV6_ADDR_LINKLOCAL)) &&
 	    likely(!(IP6CB(skb)->flags & IP6SKB_FORWARDED))) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_offload.c
@@ -114,6 +114,8 @@
 	if (likely(ops && ops->callbacks.gso_segment)) {
 		skb_reset_transport_header(skb);
 		segs = ops->callbacks.gso_segment(skb, features);
+		if (!segs)
+			skb->network_header = skb_mac_header(skb) + nhoff - skb->head;
 	}
 
 	if (IS_ERR_OR_NULL(segs))
@@ -208,7 +210,6 @@
 
 	flush += ntohs(iph->payload_len) != skb_gro_len(skb);
 
-	rcu_read_lock();
 	proto = iph->nexthdr;
 	ops = rcu_dereference(inet6_offloads[proto]);
 	if (!ops || !ops->callbacks.gro_receive) {
@@ -221,7 +222,7 @@
 
 		ops = rcu_dereference(inet6_offloads[proto]);
 		if (!ops || !ops->callbacks.gro_receive)
-			goto out_unlock;
+			goto out;
 
 		iph = ipv6_hdr(skb);
 	}
@@ -279,9 +280,6 @@
 	pp = indirect_call_gro_receive_l4(tcp6_gro_receive, udp6_gro_receive,
 					 ops->callbacks.gro_receive, head, skb);
 
-out_unlock:
-	rcu_read_unlock();
-
 out:
 	skb_gro_flush_final(skb, pp, flush);
 
@@ -331,18 +329,14 @@
 
 	iph->payload_len = htons(skb->len - nhoff - sizeof(*iph));
 
-	rcu_read_lock();
-
 	nhoff += sizeof(*iph) + ipv6_exthdrs_len(iph, &ops);
 	if (WARN_ON(!ops || !ops->callbacks.gro_complete))
-		goto out_unlock;
+		goto out;
 
 	err = INDIRECT_CALL_L4(ops->callbacks.gro_complete, tcp6_gro_complete,
 			       udp6_gro_complete, skb, nhoff);
 
-out_unlock:
-	rcu_read_unlock();
-
+out:
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_output.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_output.c
@@ -69,11 +69,15 @@
 
 	/* Be paranoid, rather than too clever. */
 	if (unlikely(hh_len > skb_headroom(skb)) && dev->header_ops) {
+		/* Make sure idev stays alive */
+		rcu_read_lock();
 		skb = skb_expand_head(skb, hh_len);
 		if (!skb) {
 			IP6_INC_STATS(net, idev, IPSTATS_MIB_OUTDISCARDS);
+			rcu_read_unlock();
 			return -ENOMEM;
 		}
+		rcu_read_unlock();
 	}
 
 	hdr = ipv6_hdr(skb);
@@ -112,7 +116,7 @@
 	if (lwtunnel_xmit_redirect(dst->lwtstate)) {
 		int res = lwtunnel_xmit(skb);
 
-		if (res < 0 || res == LWTUNNEL_XMIT_DONE)
+		if (res != LWTUNNEL_XMIT_CONTINUE)
 			return res;
 	}
 
@@ -159,7 +163,13 @@
 		int err;
 
 		skb_mark_not_on_list(segs);
-		err = ip6_fragment(net, sk, segs, ip6_finish_output2);
+		/* Last GSO segment can be smaller than gso_size (and MTU).
+		 * Adding a fragment header would produce an "atomic fragment",
+		 * which is considered harmful (RFC-8021). Avoid that.
+		 */
+		err = segs->len > mtu ?
+			ip6_fragment(net, sk, segs, ip6_finish_output2) :
+			ip6_finish_output2(net, sk, segs);
 		if (err && ret == 0)
 			ret = err;
 	}
@@ -174,7 +184,7 @@
 #if defined(CONFIG_NETFILTER) && defined(CONFIG_XFRM)
 	/* Policy lookup after SNAT yielded a new policy */
 	if (skb_dst(skb)->xfrm) {
-		IPCB(skb)->flags |= IPSKB_REROUTED;
+		IP6CB(skb)->flags |= IP6SKB_REROUTED;
 		return dst_output(net, sk, skb);
 	}
 #endif
@@ -215,7 +225,7 @@
 	skb->protocol = htons(ETH_P_IPV6);
 	skb->dev = dev;
 
-	if (unlikely(idev->cnf.disable_ipv6)) {
+	if (unlikely(!idev || READ_ONCE(idev->cnf.disable_ipv6))) {
 		IP6_INC_STATS(net, idev, IPSTATS_MIB_OUTDISCARDS);
 		kfree_skb(skb);
 		return 0;
@@ -263,11 +273,15 @@
 		head_room += opt->opt_nflen + opt->opt_flen;
 
 	if (unlikely(head_room > skb_headroom(skb))) {
+		/* Make sure idev stays alive */
+		rcu_read_lock();
 		skb = skb_expand_head(skb, head_room);
 		if (!skb) {
 			IP6_INC_STATS(net, idev, IPSTATS_MIB_OUTDISCARDS);
+			rcu_read_unlock();
 			return -ENOBUFS;
 		}
+		rcu_read_unlock();
 	}
 
 	if (opt) {
@@ -472,6 +486,9 @@
 	u32 mtu;
 
 	idev = __in6_dev_get_safely(dev_get_by_index_rcu(net, IP6CB(skb)->iif));
+	if (unlikely(!idev))
+		idev = __in6_dev_get_safely(skb->dev);
+
 	if (net->ipv6.devconf_all->forwarding == 0)
 		goto error;
 
@@ -485,7 +502,7 @@
 		goto drop;
 
 	if (!net->ipv6.devconf_all->disable_policy &&
-	    !idev->cnf.disable_policy &&
+	    (!idev || !idev->cnf.disable_policy) &&
 	    !xfrm6_policy_check(NULL, XFRM_POLICY_FWD, skb)) {
 		__IP6_INC_STATS(net, idev, IPSTATS_MIB_INDISCARDS);
 		goto drop;
@@ -527,7 +544,20 @@
 	    pneigh_lookup(&nd_tbl, net, &hdr->daddr, skb->dev, 0)) {
 		int proxied = ip6_forward_proxy_check(skb);
 		if (proxied > 0) {
-			hdr->hop_limit--;
+			/* It's tempting to decrease the hop limit
+			 * here by 1, as we do at the end of the
+			 * function too.
+			 *
+			 * But that would be incorrect, as proxying is
+			 * not forwarding.  The ip6_input function
+			 * will handle this packet locally, and it
+			 * depends on the hop limit being unchanged.
+			 *
+			 * One example is the NDP hop limit, that
+			 * always has to stay 255, but other would be
+			 * similar checks around RA packets, where the
+			 * user can even change the desired limit.
+			 */
 			return ip6_input(skb);
 		} else if (proxied < 0) {
 			__IP6_INC_STATS(net, idev, IPSTATS_MIB_INDISCARDS);
@@ -897,6 +927,9 @@
 		if (err < 0)
 			goto fail;
 
+		/* We prevent @rt from being freed. */
+		rcu_read_lock();
+
 		for (;;) {
 			/* Prepare header of the next frame,
 			 * before previous one went down. */
@@ -920,6 +953,7 @@
 		if (err == 0) {
 			IP6_INC_STATS(net, ip6_dst_idev(&rt->dst),
 				      IPSTATS_MIB_FRAGOKS);
+			rcu_read_unlock();
 			return 0;
 		}
 
@@ -927,6 +961,7 @@
 
 		IP6_INC_STATS(net, ip6_dst_idev(&rt->dst),
 			      IPSTATS_MIB_FRAGFAILS);
+		rcu_read_unlock();
 		return err;
 
 slow_path_clean:
@@ -1034,8 +1069,7 @@
 #ifdef CONFIG_IPV6_SUBTREES
 	    ip6_rt_check(&rt->rt6i_src, &fl6->saddr, np->saddr_cache) ||
 #endif
-	   (!(fl6->flowi6_flags & FLOWI_FLAG_SKIP_NH_OIF) &&
-	      (fl6->flowi6_oif && fl6->flowi6_oif != dst->dev->ifindex))) {
+	   (fl6->flowi6_oif && fl6->flowi6_oif != dst->dev->ifindex)) {
 		dst_release(dst);
 		dst = NULL;
 	}
@@ -1289,8 +1323,7 @@
 	fl6.daddr = info->key.u.ipv6.dst;
 	fl6.saddr = info->key.u.ipv6.src;
 	prio = info->key.tos;
-	fl6.flowlabel = ip6_make_flowinfo(RT_TOS(prio),
-					  info->key.label);
+	fl6.flowlabel = ip6_make_flowinfo(prio, info->key.label);
 
 	dst = ipv6_stub->ipv6_dst_lookup_flow(net, sock->sk, &fl6,
 					      NULL);
@@ -1408,8 +1441,6 @@
 		if (np->frag_size)
 			mtu = np->frag_size;
 	}
-	if (mtu < IPV6_MIN_MTU)
-		return -EINVAL;
 	cork->base.fragsize = mtu;
 	cork->base.gso_size = ipc6->gso_size;
 	cork->base.tx_flags = 0;
@@ -1433,7 +1464,7 @@
 			     struct page_frag *pfrag,
 			     int getfrag(void *from, char *to, int offset,
 					 int len, int odd, struct sk_buff *skb),
-			     void *from, int length, int transhdrlen,
+			     void *from, size_t length, int transhdrlen,
 			     unsigned int flags, struct ipcm6_cookie *ipc6)
 {
 	struct sk_buff *skb, *skb_prev = NULL;
@@ -1463,16 +1494,14 @@
 	mtu = cork->gso_size ? IP6_MAX_MTU : cork->fragsize;
 	orig_mtu = mtu;
 
-	if (cork->tx_flags & SKBTX_ANY_SW_TSTAMP &&
+	if (cork->tx_flags & SKBTX_ANY_TSTAMP &&
 	    sk->sk_tsflags & SOF_TIMESTAMPING_OPT_ID)
-		tskey = sk->sk_tskey++;
+		tskey = atomic_inc_return(&sk->sk_tskey) - 1;
 
 	hh_len = LL_RESERVED_SPACE(rt->dst.dev);
 
 	fragheaderlen = sizeof(struct ipv6hdr) + rt->rt6i_nfheader_len +
 			(opt ? opt->opt_nflen : 0);
-	maxfraglen = ((mtu - fragheaderlen) & ~7) + fragheaderlen -
-		     sizeof(struct frag_hdr);
 
 	headersize = sizeof(struct ipv6hdr) +
 		     (opt ? opt->opt_flen + opt->opt_nflen : 0) +
@@ -1480,6 +1509,13 @@
 		      sizeof(struct frag_hdr) : 0) +
 		     rt->rt6i_nfheader_len;
 
+	if (mtu <= fragheaderlen ||
+	    ((mtu - fragheaderlen) & ~7) + fragheaderlen <= sizeof(struct frag_hdr))
+		goto emsgsize;
+
+	maxfraglen = ((mtu - fragheaderlen) & ~7) + fragheaderlen -
+		     sizeof(struct frag_hdr);
+
 	/* as per RFC 7112 section 5, the entire IPv6 Header Chain must fit
 	 * the first fragment
 	 */
@@ -1773,7 +1809,7 @@
 int ip6_append_data(struct sock *sk,
 		    int getfrag(void *from, char *to, int offset, int len,
 				int odd, struct sk_buff *skb),
-		    void *from, int length, int transhdrlen,
+		    void *from, size_t length, int transhdrlen,
 		    struct ipcm6_cookie *ipc6, struct flowi6 *fl6,
 		    struct rt6_info *rt, unsigned int flags)
 {
@@ -1893,8 +1929,13 @@
 	IP6_UPD_PO_STATS(net, rt->rt6i_idev, IPSTATS_MIB_OUT, skb->len);
 	if (proto == IPPROTO_ICMPV6) {
 		struct inet6_dev *idev = ip6_dst_idev(skb_dst(skb));
+		u8 icmp6_type;
 
-		ICMP6MSGOUT_INC_STATS(net, idev, icmp6_hdr(skb)->icmp6_type);
+		if (sk->sk_socket->type == SOCK_RAW && !inet_sk(sk)->hdrincl)
+			icmp6_type = fl6->fl6_icmp_type;
+		else
+			icmp6_type = icmp6_hdr(skb)->icmp6_type;
+		ICMP6MSGOUT_INC_STATS(net, idev, icmp6_type);
 		ICMP6_INC_STATS(net, idev, ICMP6_MIB_OUTMSGS);
 	}
 
@@ -1909,6 +1950,7 @@
 	struct rt6_info *rt = (struct rt6_info *)skb_dst(skb);
 	int err;
 
+	rcu_read_lock();
 	err = ip6_local_out(net, skb->sk, skb);
 	if (err) {
 		if (err > 0)
@@ -1918,6 +1960,7 @@
 				      IPSTATS_MIB_OUTDISCARDS);
 	}
 
+	rcu_read_unlock();
 	return err;
 }
 
@@ -1960,7 +2003,7 @@
 struct sk_buff *ip6_make_skb(struct sock *sk,
 			     int getfrag(void *from, char *to, int offset,
 					 int len, int odd, struct sk_buff *skb),
-			     void *from, int length, int transhdrlen,
+			     void *from, size_t length, int transhdrlen,
 			     struct ipcm6_cookie *ipc6, struct flowi6 *fl6,
 			     struct rt6_info *rt, unsigned int flags,
 			     struct inet_cork_full *cork)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_tunnel.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_tunnel.c
@@ -401,7 +401,7 @@
 	const struct ipv6hdr *ipv6h = (const struct ipv6hdr *)raw;
 	unsigned int nhoff = raw - skb->data;
 	unsigned int off = nhoff + sizeof(*ipv6h);
-	u8 next, nexthdr = ipv6h->nexthdr;
+	u8 nexthdr = ipv6h->nexthdr;
 
 	while (ipv6_ext_hdr(nexthdr) && nexthdr != NEXTHDR_NONE) {
 		struct ipv6_opt_hdr *hdr;
@@ -412,25 +412,25 @@
 
 		hdr = (struct ipv6_opt_hdr *)(skb->data + off);
 		if (nexthdr == NEXTHDR_FRAGMENT) {
-			struct frag_hdr *frag_hdr = (struct frag_hdr *) hdr;
-			if (frag_hdr->frag_off)
-				break;
 			optlen = 8;
 		} else if (nexthdr == NEXTHDR_AUTH) {
 			optlen = ipv6_authlen(hdr);
 		} else {
 			optlen = ipv6_optlen(hdr);
 		}
-		/* cache hdr->nexthdr, since pskb_may_pull() might
-		 * invalidate hdr
-		 */
-		next = hdr->nexthdr;
-		if (nexthdr == NEXTHDR_DEST) {
-			u16 i = 2;
 
-			/* Remember : hdr is no longer valid at this point. */
-			if (!pskb_may_pull(skb, off + optlen))
+		if (!pskb_may_pull(skb, off + optlen))
+			break;
+
+		hdr = (struct ipv6_opt_hdr *)(skb->data + off);
+		if (nexthdr == NEXTHDR_FRAGMENT) {
+			struct frag_hdr *frag_hdr = (struct frag_hdr *)hdr;
+
+			if (frag_hdr->frag_off)
 				break;
+		}
+		if (nexthdr == NEXTHDR_DEST) {
+			u16 i = 2;
 
 			while (1) {
 				struct ipv6_tlv_tnl_enc_lim *tel;
@@ -451,7 +451,7 @@
 					i++;
 			}
 		}
-		nexthdr = next;
+		nexthdr = hdr->nexthdr;
 		off += optlen;
 	}
 	return 0;
@@ -798,9 +798,8 @@
 						struct sk_buff *skb),
 			 bool log_ecn_err)
 {
-	struct pcpu_sw_netstats *tstats;
-	const struct ipv6hdr *ipv6h = ipv6_hdr(skb);
-	int err;
+	const struct ipv6hdr *ipv6h;
+	int nh, err;
 
 	if ((!(tpi->flags & TUNNEL_CSUM) &&
 	     (tunnel->parms.i_flags & TUNNEL_CSUM)) ||
@@ -832,7 +831,6 @@
 			goto drop;
 		}
 
-		ipv6h = ipv6_hdr(skb);
 		skb->protocol = eth_type_trans(skb, tunnel->dev);
 		skb_postpull_rcsum(skb, eth_hdr(skb), ETH_HLEN);
 	} else {
@@ -840,7 +838,23 @@
 		skb_reset_mac_header(skb);
 	}
 
+	/* Save offset of outer header relative to skb->head,
+	 * because we are going to reset the network header to the inner header
+	 * and might change skb->head.
+	 */
+	nh = skb_network_header(skb) - skb->head;
+
 	skb_reset_network_header(skb);
+
+	if (!pskb_inet_may_pull(skb)) {
+		DEV_STATS_INC(tunnel->dev, rx_length_errors);
+		DEV_STATS_INC(tunnel->dev, rx_errors);
+		goto drop;
+	}
+
+	/* Get the outer header. */
+	ipv6h = (struct ipv6hdr *)(skb->head + nh);
+
 	memset(skb->cb, 0, sizeof(struct inet6_skb_parm));
 
 	__skb_tunnel_rx(skb, tunnel->dev, tunnel->net);
@@ -858,11 +872,7 @@
 		}
 	}
 
-	tstats = this_cpu_ptr(tunnel->dev->tstats);
-	u64_stats_update_begin(&tstats->syncp);
-	tstats->rx_packets++;
-	tstats->rx_bytes += skb->len;
-	u64_stats_update_end(&tstats->syncp);
+	dev_sw_netstats_rx_add(tunnel->dev, skb->len);
 
 	skb_scrub_packet(skb, !net_eq(tunnel->net, dev_net(tunnel->dev)));
 
@@ -1036,14 +1046,14 @@
 
 		if (unlikely(!ipv6_chk_addr_and_flags(net, laddr, ldev, false,
 						      0, IFA_F_TENTATIVE)))
-			pr_warn("%s xmit: Local address not yet configured!\n",
-				p->name);
+			pr_warn_ratelimited("%s xmit: Local address not yet configured!\n",
+					    p->name);
 		else if (!(p->flags & IP6_TNL_F_ALLOW_LOCAL_REMOTE) &&
 			 !ipv6_addr_is_multicast(raddr) &&
 			 unlikely(ipv6_chk_addr_and_flags(net, raddr, ldev,
 							  true, 0, IFA_F_TENTATIVE)))
-			pr_warn("%s xmit: Routing loop! Remote address found on this node!\n",
-				p->name);
+			pr_warn_ratelimited("%s xmit: Routing loop! Remote address found on this node!\n",
+					    p->name);
 		else
 			ret = 1;
 		rcu_read_unlock();
@@ -1237,8 +1247,8 @@
 	 */
 	max_headroom = LL_RESERVED_SPACE(dst->dev) + sizeof(struct ipv6hdr)
 			+ dst->header_len + t->hlen;
-	if (max_headroom > dev->needed_headroom)
-		dev->needed_headroom = max_headroom;
+	if (max_headroom > READ_ONCE(dev->needed_headroom))
+		WRITE_ONCE(dev->needed_headroom, max_headroom);
 
 	err = ip6_tnl_encap(skb, t, &proto, fl6);
 	if (err)
@@ -1446,8 +1456,8 @@
 	struct net_device *tdev = NULL;
 	struct __ip6_tnl_parm *p = &t->parms;
 	struct flowi6 *fl6 = &t->fl.u.ip6;
-	unsigned int mtu;
 	int t_hlen;
+	int mtu;
 
 	memcpy(dev->dev_addr, &p->laddr, sizeof(struct in6_addr));
 	memcpy(dev->broadcast, &p->raddr, sizeof(struct in6_addr));
@@ -1491,15 +1501,17 @@
 			tdev = __dev_get_by_index(t->net, p->link);
 
 		if (tdev) {
-			dev->hard_header_len = tdev->hard_header_len + t_hlen;
+			dev->needed_headroom = tdev->hard_header_len +
+				tdev->needed_headroom + t_hlen;
 			mtu = min_t(unsigned int, tdev->mtu, IP6_MAX_MTU);
 
-			dev->mtu = mtu - t_hlen;
+			mtu = mtu - t_hlen;
 			if (!(t->parms.flags & IP6_TNL_F_IGN_ENCAP_LIMIT))
-				dev->mtu -= 8;
+				mtu -= 8;
 
-			if (dev->mtu < IPV6_MIN_MTU)
-				dev->mtu = IPV6_MIN_MTU;
+			if (mtu < IPV6_MIN_MTU)
+				mtu = IPV6_MIN_MTU;
+			WRITE_ONCE(dev->mtu, mtu);
 		}
 	}
 }
@@ -1718,7 +1730,9 @@
 int ip6_tnl_change_mtu(struct net_device *dev, int new_mtu)
 {
 	struct ip6_tnl *tnl = netdev_priv(dev);
+	int t_hlen;
 
+	t_hlen = tnl->hlen + sizeof(struct ipv6hdr);
 	if (tnl->parms.proto == IPPROTO_IPV6) {
 		if (new_mtu < IPV6_MIN_MTU)
 			return -EINVAL;
@@ -1727,10 +1741,10 @@
 			return -EINVAL;
 	}
 	if (tnl->parms.proto == IPPROTO_IPV6 || tnl->parms.proto == 0) {
-		if (new_mtu > IP6_MAX_MTU - dev->hard_header_len)
+		if (new_mtu > IP6_MAX_MTU - dev->hard_header_len - t_hlen)
 			return -EINVAL;
 	} else {
-		if (new_mtu > IP_MAX_MTU - dev->hard_header_len)
+		if (new_mtu > IP_MAX_MTU - dev->hard_header_len - t_hlen)
 			return -EINVAL;
 	}
 	dev->mtu = new_mtu;
@@ -1876,12 +1890,11 @@
 	t_hlen = t->hlen + sizeof(struct ipv6hdr);
 
 	dev->type = ARPHRD_TUNNEL6;
-	dev->hard_header_len = LL_MAX_HEADER + t_hlen;
 	dev->mtu = ETH_DATA_LEN - t_hlen;
 	if (!(t->parms.flags & IP6_TNL_F_IGN_ENCAP_LIMIT))
 		dev->mtu -= 8;
 	dev->min_mtu = ETH_MIN_MTU;
-	dev->max_mtu = IP6_MAX_MTU - dev->hard_header_len;
+	dev->max_mtu = IP6_MAX_MTU - dev->hard_header_len - t_hlen;
 
 	dev_hold(dev);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6_vti.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6_vti.c
@@ -570,12 +570,12 @@
 		    vti6_addr_conflict(t, ipv6_hdr(skb)))
 			goto tx_err;
 
-		xfrm_decode_session(skb, &fl, AF_INET6);
 		memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
+		xfrm_decode_session(skb, &fl, AF_INET6);
 		break;
 	case htons(ETH_P_IP):
-		xfrm_decode_session(skb, &fl, AF_INET);
 		memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
+		xfrm_decode_session(skb, &fl, AF_INET);
 		break;
 	default:
 		goto tx_err;
@@ -808,6 +808,8 @@
 	struct net *net = dev_net(dev);
 	struct vti6_net *ip6n = net_generic(net, vti6_net_id);
 
+	memset(&p1, 0, sizeof(p1));
+
 	switch (cmd) {
 	case SIOCGETTUNNEL:
 		if (dev == ip6n->fb_tnl_dev) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ip6mr.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ip6mr.c
@@ -248,7 +248,9 @@
 	return 0;
 
 err2:
+	rtnl_lock();
 	ip6mr_free_table(mrt);
+	rtnl_unlock();
 err1:
 	fib_rules_unregister(ops);
 	return err;
@@ -737,7 +739,7 @@
 
 	in6_dev = __in6_dev_get(dev);
 	if (in6_dev) {
-		in6_dev->cnf.mc_forwarding--;
+		atomic_dec(&in6_dev->cnf.mc_forwarding);
 		inet6_netconf_notify_devconf(dev_net(dev), RTM_NEWNETCONF,
 					     NETCONFA_MC_FORWARDING,
 					     dev->ifindex, &in6_dev->cnf);
@@ -905,7 +907,7 @@
 
 	in6_dev = __in6_dev_get(dev);
 	if (in6_dev) {
-		in6_dev->cnf.mc_forwarding++;
+		atomic_inc(&in6_dev->cnf.mc_forwarding);
 		inet6_netconf_notify_devconf(dev_net(dev), RTM_NEWNETCONF,
 					     NETCONFA_MC_FORWARDING,
 					     dev->ifindex, &in6_dev->cnf);
@@ -1066,7 +1068,7 @@
 		   And all this only to mangle msg->im6_msgtype and
 		   to set msg->im6_mbz to "mbz" :-)
 		 */
-		skb_push(skb, -skb_network_offset(pkt));
+		__skb_pull(skb, skb_network_offset(pkt));
 
 		skb_push(skb, sizeof(*msg));
 		skb_reset_transport_header(skb);
@@ -1555,7 +1557,7 @@
 	} else {
 		rcu_assign_pointer(mrt->mroute_sk, sk);
 		sock_set_flag(sk, SOCK_RCU_FREE);
-		net->ipv6.devconf_all->mc_forwarding++;
+		atomic_inc(&net->ipv6.devconf_all->mc_forwarding);
 	}
 	write_unlock_bh(&mrt_lock);
 
@@ -1588,7 +1590,7 @@
 			 * so the RCU grace period before sk freeing
 			 * is guaranteed by sk_destruct()
 			 */
-			net->ipv6.devconf_all->mc_forwarding--;
+			atomic_dec(&net->ipv6.devconf_all->mc_forwarding);
 			write_unlock_bh(&mrt_lock);
 			inet6_netconf_notify_devconf(net, RTM_NEWNETCONF,
 						     NETCONFA_MC_FORWARDING,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ipv6_sockglue.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ipv6_sockglue.c
@@ -208,7 +208,7 @@
 
 	if (optlen < GROUP_FILTER_SIZE(0))
 		return -EINVAL;
-	if (optlen > sysctl_optmem_max)
+	if (optlen > READ_ONCE(sysctl_optmem_max))
 		return -ENOBUFS;
 
 	gsf = memdup_sockptr(optval, optlen);
@@ -242,7 +242,7 @@
 
 	if (optlen < size0)
 		return -EINVAL;
-	if (optlen > sysctl_optmem_max - 4)
+	if (optlen > READ_ONCE(sysctl_optmem_max) - 4)
 		return -ENOBUFS;
 
 	p = kmalloc(optlen + 4, GFP_KERNEL);
@@ -417,15 +417,18 @@
 		rtnl_lock();
 	lock_sock(sk);
 
+	/* Another thread has converted the socket into IPv4 with
+	 * IPV6_ADDRFORM concurrently.
+	 */
+	if (unlikely(sk->sk_family != AF_INET6))
+		goto unlock;
+
 	switch (optname) {
 
 	case IPV6_ADDRFORM:
 		if (optlen < sizeof(int))
 			goto e_inval;
 		if (val == PF_INET) {
-			struct ipv6_txoptions *opt;
-			struct sk_buff *pktopt;
-
 			if (sk->sk_type == SOCK_RAW)
 				break;
 
@@ -456,7 +459,6 @@
 				break;
 			}
 
-			fl6_free_socklist(sk);
 			__ipv6_sock_mc_close(sk);
 			__ipv6_sock_ac_close(sk);
 
@@ -469,12 +471,14 @@
 
 			if (sk->sk_protocol == IPPROTO_TCP) {
 				struct inet_connection_sock *icsk = inet_csk(sk);
-				local_bh_disable();
+
 				sock_prot_inuse_add(net, sk->sk_prot, -1);
 				sock_prot_inuse_add(net, &tcp_prot, 1);
-				local_bh_enable();
-				sk->sk_prot = &tcp_prot;
-				icsk->icsk_af_ops = &ipv4_specific;
+
+				/* Paired with READ_ONCE(sk->sk_prot) in inet6_stream_ops */
+				WRITE_ONCE(sk->sk_prot, &tcp_prot);
+				/* Paired with READ_ONCE() in tcp_(get|set)sockopt() */
+				WRITE_ONCE(icsk->icsk_af_ops, &ipv4_specific);
 				sk->sk_socket->ops = &inet_stream_ops;
 				sk->sk_family = PF_INET;
 				tcp_sync_mss(sk, icsk->icsk_pmtu_cookie);
@@ -483,22 +487,23 @@
 
 				if (sk->sk_protocol == IPPROTO_UDPLITE)
 					prot = &udplite_prot;
-				local_bh_disable();
+
 				sock_prot_inuse_add(net, sk->sk_prot, -1);
 				sock_prot_inuse_add(net, prot, 1);
-				local_bh_enable();
-				sk->sk_prot = prot;
+
+				/* Paired with READ_ONCE(sk->sk_prot) in inet6_dgram_ops */
+				WRITE_ONCE(sk->sk_prot, prot);
 				sk->sk_socket->ops = &inet_dgram_ops;
 				sk->sk_family = PF_INET;
 			}
-			opt = xchg((__force struct ipv6_txoptions **)&np->opt,
-				   NULL);
-			if (opt) {
-				atomic_sub(opt->tot_len, &sk->sk_omem_alloc);
-				txopt_put(opt);
-			}
-			pktopt = xchg(&np->pktoptions, NULL);
-			kfree_skb(pktopt);
+
+			/* Disable all options not to allocate memory anymore,
+			 * but there is still a race.  See the lockless path
+			 * in udpv6_sendmsg() and ipv6_local_rxpmtu().
+			 */
+			np->rxopt.all = 0;
+
+			inet6_cleanup_sock(sk);
 
 			/*
 			 * ... and add it to the refcnt debug socks count
@@ -976,6 +981,7 @@
 		break;
 	}
 
+unlock:
 	release_sock(sk);
 	if (needs_rtnl)
 		rtnl_unlock();
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/mcast.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/mcast.c
@@ -460,10 +460,10 @@
 				newpsl->sl_addr[i] = psl->sl_addr[i];
 			atomic_sub(struct_size(psl, sl_addr, psl->sl_max),
 				   &sk->sk_omem_alloc);
-			kfree_rcu(psl, rcu);
 		}
+		rcu_assign_pointer(pmc->sflist, newpsl);
+		kfree_rcu(psl, rcu);
 		psl = newpsl;
-		rcu_assign_pointer(pmc->sflist, psl);
 	}
 	rv = 1;	/* > 0 for insert logic below if sl_count is 0 */
 	for (i = 0; i < psl->sl_count; i++) {
@@ -565,12 +565,12 @@
 			       psl->sl_count, psl->sl_addr, 0);
 		atomic_sub(struct_size(psl, sl_addr, psl->sl_max),
 			   &sk->sk_omem_alloc);
-		kfree_rcu(psl, rcu);
 	} else {
 		ip6_mc_del_src(idev, group, pmc->sfmode, 0, NULL, 0);
 	}
-	mutex_unlock(&idev->mc_lock);
 	rcu_assign_pointer(pmc->sflist, newpsl);
+	mutex_unlock(&idev->mc_lock);
+	kfree_rcu(psl, rcu);
 	pmc->sfmode = gsf->gf_fmode;
 	err = 0;
 done:
@@ -1371,27 +1371,23 @@
 }
 
 /* called with rcu_read_lock() */
-int igmp6_event_query(struct sk_buff *skb)
+void igmp6_event_query(struct sk_buff *skb)
 {
 	struct inet6_dev *idev = __in6_dev_get(skb->dev);
 
-	if (!idev)
-		return -EINVAL;
-
-	if (idev->dead) {
-		kfree_skb(skb);
-		return -ENODEV;
-	}
+	if (!idev || idev->dead)
+		goto out;
 
 	spin_lock_bh(&idev->mc_query_lock);
 	if (skb_queue_len(&idev->mc_query_queue) < MLD_MAX_SKBS) {
 		__skb_queue_tail(&idev->mc_query_queue, skb);
 		if (!mod_delayed_work(mld_wq, &idev->mc_query_work, 0))
 			in6_dev_hold(idev);
+		skb = NULL;
 	}
 	spin_unlock_bh(&idev->mc_query_lock);
-
-	return 0;
+out:
+	kfree_skb(skb);
 }
 
 static void __mld_query_work(struct sk_buff *skb)
@@ -1526,7 +1522,6 @@
 
 		if (++cnt >= MLD_MAX_QUEUE) {
 			rework = true;
-			schedule_delayed_work(&idev->mc_query_work, 0);
 			break;
 		}
 	}
@@ -1537,32 +1532,30 @@
 		__mld_query_work(skb);
 	mutex_unlock(&idev->mc_lock);
 
-	if (!rework)
-		in6_dev_put(idev);
+	if (rework && queue_delayed_work(mld_wq, &idev->mc_query_work, 0))
+		return;
+
+	in6_dev_put(idev);
 }
 
 /* called with rcu_read_lock() */
-int igmp6_event_report(struct sk_buff *skb)
+void igmp6_event_report(struct sk_buff *skb)
 {
 	struct inet6_dev *idev = __in6_dev_get(skb->dev);
 
-	if (!idev)
-		return -EINVAL;
-
-	if (idev->dead) {
-		kfree_skb(skb);
-		return -ENODEV;
-	}
+	if (!idev || idev->dead)
+		goto out;
 
 	spin_lock_bh(&idev->mc_report_lock);
 	if (skb_queue_len(&idev->mc_report_queue) < MLD_MAX_SKBS) {
 		__skb_queue_tail(&idev->mc_report_queue, skb);
 		if (!mod_delayed_work(mld_wq, &idev->mc_report_work, 0))
 			in6_dev_hold(idev);
+		skb = NULL;
 	}
 	spin_unlock_bh(&idev->mc_report_lock);
-
-	return 0;
+out:
+	kfree_skb(skb);
 }
 
 static void __mld_report_work(struct sk_buff *skb)
@@ -1632,7 +1625,6 @@
 
 		if (++cnt >= MLD_MAX_QUEUE) {
 			rework = true;
-			schedule_delayed_work(&idev->mc_report_work, 0);
 			break;
 		}
 	}
@@ -1643,8 +1635,10 @@
 		__mld_report_work(skb);
 	mutex_unlock(&idev->mc_lock);
 
-	if (!rework)
-		in6_dev_put(idev);
+	if (rework && queue_delayed_work(mld_wq, &idev->mc_report_work, 0))
+		return;
+
+	in6_dev_put(idev);
 }
 
 static bool is_in(struct ifmcaddr6 *pmc, struct ip6_sf_list *psf, int type,
@@ -1737,21 +1731,19 @@
 	struct net_device *dev = idev->dev;
 	int hlen = LL_RESERVED_SPACE(dev);
 	int tlen = dev->needed_tailroom;
-	struct net *net = dev_net(dev);
 	const struct in6_addr *saddr;
 	struct in6_addr addr_buf;
 	struct mld2_report *pmr;
 	struct sk_buff *skb;
 	unsigned int size;
 	struct sock *sk;
-	int err;
+	struct net *net;
 
-	sk = net->ipv6.igmp_sk;
 	/* we assume size > sizeof(ra) here
 	 * Also try to not allocate high-order pages for big MTU
 	 */
 	size = min_t(int, mtu, PAGE_SIZE / 2) + hlen + tlen;
-	skb = sock_alloc_send_skb(sk, size, 1, &err);
+	skb = alloc_skb(size, GFP_KERNEL);
 	if (!skb)
 		return NULL;
 
@@ -1759,7 +1751,13 @@
 	skb_reserve(skb, hlen);
 	skb_tailroom_reserve(skb, mtu, tlen);
 
-	if (__ipv6_get_lladdr(idev, &addr_buf, IFA_F_TENTATIVE)) {
+	rcu_read_lock();
+
+	net = dev_net_rcu(dev);
+	sk = net->ipv6.igmp_sk;
+	skb_set_owner_w(skb, sk);
+
+	if (ipv6_get_lladdr(dev, &addr_buf, IFA_F_TENTATIVE)) {
 		/* <draft-ietf-magma-mld-source-05.txt>:
 		 * use unspecified address as the source address
 		 * when a valid link-local address is not available.
@@ -1770,6 +1768,8 @@
 
 	ip6_mc_hdr(sk, skb, dev, saddr, &mld2_all_mcr, NEXTHDR_HOP, 0);
 
+	rcu_read_unlock();
+
 	skb_put_data(skb, ra, sizeof(ra));
 
 	skb_set_transport_header(skb, skb_tail_pointer(skb) - skb->data);
@@ -2728,11 +2728,14 @@
 	/* Should stop work after group drop. or we will
 	 * start work again in mld_ifc_event()
 	 */
-	synchronize_net();
 	mld_query_stop_work(idev);
 	mld_report_stop_work(idev);
+
+	mutex_lock(&idev->mc_lock);
 	mld_ifc_stop_work(idev);
 	mld_gq_stop_work(idev);
+	mutex_unlock(&idev->mc_lock);
+
 	mld_dad_stop_work(idev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ndisc.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ndisc.c
@@ -196,7 +196,8 @@
 static inline int ndisc_is_useropt(const struct net_device *dev,
 				   struct nd_opt_hdr *opt)
 {
-	return opt->nd_opt_type == ND_OPT_RDNSS ||
+	return opt->nd_opt_type == ND_OPT_PREFIX_INFO ||
+		opt->nd_opt_type == ND_OPT_RDNSS ||
 		opt->nd_opt_type == ND_OPT_DNSSL ||
 		opt->nd_opt_type == ND_OPT_CAPTIVE_PORTAL ||
 		opt->nd_opt_type == ND_OPT_PREF64 ||
@@ -225,6 +226,7 @@
 		return NULL;
 	memset(ndopts, 0, sizeof(*ndopts));
 	while (opt_len) {
+		bool unknown = false;
 		int l;
 		if (opt_len < sizeof(struct nd_opt_hdr))
 			return NULL;
@@ -260,22 +262,23 @@
 			break;
 #endif
 		default:
-			if (ndisc_is_useropt(dev, nd_opt)) {
-				ndopts->nd_useropts_end = nd_opt;
-				if (!ndopts->nd_useropts)
-					ndopts->nd_useropts = nd_opt;
-			} else {
-				/*
-				 * Unknown options must be silently ignored,
-				 * to accommodate future extension to the
-				 * protocol.
-				 */
-				ND_PRINTK(2, notice,
-					  "%s: ignored unsupported option; type=%d, len=%d\n",
-					  __func__,
-					  nd_opt->nd_opt_type,
-					  nd_opt->nd_opt_len);
-			}
+			unknown = true;
+		}
+		if (ndisc_is_useropt(dev, nd_opt)) {
+			ndopts->nd_useropts_end = nd_opt;
+			if (!ndopts->nd_useropts)
+				ndopts->nd_useropts = nd_opt;
+		} else if (unknown) {
+			/*
+			 * Unknown options must be silently ignored,
+			 * to accommodate future extension to the
+			 * protocol.
+			 */
+			ND_PRINTK(2, notice,
+				  "%s: ignored unsupported option; type=%d, len=%d\n",
+				  __func__,
+				  nd_opt->nd_opt_type,
+				  nd_opt->nd_opt_len);
 		}
 next_opt:
 		opt_len -= l;
@@ -414,15 +417,11 @@
 {
 	int hlen = LL_RESERVED_SPACE(dev);
 	int tlen = dev->needed_tailroom;
-	struct sock *sk = dev_net(dev)->ipv6.ndisc_sk;
 	struct sk_buff *skb;
 
 	skb = alloc_skb(hlen + sizeof(struct ipv6hdr) + len + tlen, GFP_ATOMIC);
-	if (!skb) {
-		ND_PRINTK(0, err, "ndisc: %s failed to allocate an skb\n",
-			  __func__);
+	if (!skb)
 		return NULL;
-	}
 
 	skb->protocol = htons(ETH_P_IPV6);
 	skb->dev = dev;
@@ -433,7 +432,9 @@
 	/* Manually assign socket ownership as we avoid calling
 	 * sock_alloc_send_pskb() to bypass wmem buffer limits
 	 */
-	skb_set_owner_w(skb, sk);
+	rcu_read_lock();
+	skb_set_owner_w(skb, dev_net_rcu(dev)->ipv6.ndisc_sk);
+	rcu_read_unlock();
 
 	return skb;
 }
@@ -470,16 +471,20 @@
 			   const struct in6_addr *daddr,
 			   const struct in6_addr *saddr)
 {
+	struct icmp6hdr *icmp6h = icmp6_hdr(skb);
 	struct dst_entry *dst = skb_dst(skb);
-	struct net *net = dev_net(skb->dev);
-	struct sock *sk = net->ipv6.ndisc_sk;
 	struct inet6_dev *idev;
+	struct net *net;
+	struct sock *sk;
 	int err;
-	struct icmp6hdr *icmp6h = icmp6_hdr(skb);
 	u8 type;
 
 	type = icmp6h->icmp6_type;
 
+	rcu_read_lock();
+
+	net = dev_net_rcu(skb->dev);
+	sk = net->ipv6.ndisc_sk;
 	if (!dst) {
 		struct flowi6 fl6;
 		int oif = skb->dev->ifindex;
@@ -487,6 +492,7 @@
 		icmpv6_flow_init(sk, &fl6, type, saddr, daddr, oif);
 		dst = icmp6_dst_alloc(skb->dev, &fl6);
 		if (IS_ERR(dst)) {
+			rcu_read_unlock();
 			kfree_skb(skb);
 			return;
 		}
@@ -501,7 +507,6 @@
 
 	ip6_nd_hdr(skb, saddr, daddr, inet6_sk(sk)->hop_limit, skb->len);
 
-	rcu_read_lock();
 	idev = __in6_dev_get(dst->dev);
 	IP6_UPD_PO_STATS(net, idev, IPSTATS_MIB_OUT, skb->len);
 
@@ -1269,6 +1274,14 @@
 		goto skip_defrtr;
 	}
 
+	lifetime = ntohs(ra_msg->icmph.icmp6_rt_lifetime);
+	if (lifetime != 0 && lifetime < in6_dev->cnf.accept_ra_min_lft) {
+		ND_PRINTK(2, info,
+			  "RA: router lifetime (%ds) is too short: %s\n",
+			  lifetime, skb->dev->name);
+		goto skip_defrtr;
+	}
+
 	/* Do not accept RA with source-addr found on local machine unless
 	 * accept_ra_from_local is set to true.
 	 */
@@ -1281,8 +1294,6 @@
 		goto skip_defrtr;
 	}
 
-	lifetime = ntohs(ra_msg->icmph.icmp6_rt_lifetime);
-
 #ifdef CONFIG_IPV6_ROUTER_PREF
 	pref = ra_msg->icmph.icmp6_router_pref;
 	/* 10b is handled as if it were 00b (medium) */
@@ -1317,6 +1328,9 @@
 	if (!rt && lifetime) {
 		ND_PRINTK(3, info, "RA: adding default router\n");
 
+		if (neigh)
+			neigh_release(neigh);
+
 		rt = rt6_add_dflt_router(net, &ipv6_hdr(skb)->saddr,
 					 skb->dev, pref, defrtr_usr_metric);
 		if (!rt) {
@@ -1450,6 +1464,9 @@
 			if (ri->prefix_len == 0 &&
 			    !in6_dev->cnf.accept_ra_defrtr)
 				continue;
+			if (ri->lifetime != 0 &&
+			    ntohl(ri->lifetime) < in6_dev->cnf.accept_ra_min_lft)
+				continue;
 			if (ri->prefix_len < in6_dev->cnf.accept_ra_rt_info_min_plen)
 				continue;
 			if (ri->prefix_len > in6_dev->cnf.accept_ra_rt_info_max_plen)
@@ -1604,7 +1621,7 @@
 	bool ret;
 
 	if (netif_is_l3_master(skb->dev)) {
-		dev = __dev_get_by_index(dev_net(skb->dev), IPCB(skb)->iif);
+		dev = dev_get_by_index_rcu(dev_net(skb->dev), IPCB(skb)->iif);
 		if (!dev)
 			return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter.c
@@ -24,14 +24,13 @@
 {
 	const struct ipv6hdr *iph = ipv6_hdr(skb);
 	struct sock *sk = sk_to_full_sk(sk_partial);
+	struct net_device *dev = skb_dst(skb)->dev;
 	struct flow_keys flkeys;
 	unsigned int hh_len;
 	struct dst_entry *dst;
 	int strict = (ipv6_addr_type(&iph->daddr) &
 		      (IPV6_ADDR_MULTICAST | IPV6_ADDR_LINKLOCAL));
 	struct flowi6 fl6 = {
-		.flowi6_oif = sk && sk->sk_bound_dev_if ? sk->sk_bound_dev_if :
-			strict ? skb_dst(skb)->dev->ifindex : 0,
 		.flowi6_mark = skb->mark,
 		.flowi6_uid = sock_net_uid(net, sk),
 		.daddr = iph->daddr,
@@ -39,6 +38,13 @@
 	};
 	int err;
 
+	if (sk && sk->sk_bound_dev_if)
+		fl6.flowi6_oif = sk->sk_bound_dev_if;
+	else if (strict)
+		fl6.flowi6_oif = dev->ifindex;
+	else
+		fl6.flowi6_oif = l3mdev_master_ifindex(dev);
+
 	fib6_rules_early_flow_dissect(net, skb, &fl6, &flkeys);
 	dst = ip6_route_output(net, sk, &fl6);
 	err = dst->error;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/ip6_tables.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/ip6_tables.c
@@ -381,6 +381,17 @@
 	else return verdict;
 }
 
+static bool next_offset_ok(const struct xt_table_info *t, unsigned int newpos)
+{
+	if (newpos > t->size - sizeof(struct ip6t_entry))
+		return false;
+
+	if (newpos % __alignof__(struct ip6t_entry) != 0)
+		return false;
+
+	return true;
+}
+
 /* Figures out from what hook each rule can be called: returns 0 if
    there are loops.  Puts hook bitmask in comefrom. */
 static int
@@ -436,6 +447,8 @@
 
 				/* Move along one */
 				size = e->next_offset;
+				if (!next_offset_ok(newinfo, pos + size))
+					return 0;
 				e = entry0 + pos + size;
 				if (pos + size >= newinfo->size)
 					return 0;
@@ -457,6 +470,10 @@
 					if (newpos >= newinfo->size)
 						return 0;
 				}
+
+				if (!next_offset_ok(newinfo, newpos))
+					return 0;
+
 				e = entry0 + newpos;
 				e->counters.pcnt = pos;
 				pos = newpos;
@@ -1062,7 +1079,6 @@
 	struct xt_counters *counters;
 	struct ip6t_entry *iter;
 
-	ret = 0;
 	counters = xt_counters_alloc(num_counters);
 	if (!counters) {
 		ret = -ENOMEM;
@@ -1108,7 +1124,7 @@
 		net_warn_ratelimited("ip6tables: counters copy to user failed while replacing table\n");
 	}
 	vfree(counters);
-	return ret;
+	return 0;
 
  put_module:
 	module_put(t->me);
@@ -1128,6 +1144,8 @@
 	void *loc_cpu_entry;
 	struct ip6t_entry *iter;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -1136,6 +1154,8 @@
 		return -ENOMEM;
 	if (tmp.num_counters == 0)
 		return -EINVAL;
+	if ((u64)len < (u64)tmp.size + sizeof(tmp))
+		return -EINVAL;
 
 	tmp.name[sizeof(tmp.name)-1] = 0;
 
@@ -1504,6 +1524,8 @@
 	void *loc_cpu_entry;
 	struct ip6t_entry *iter;
 
+	if (len < sizeof(tmp))
+		return -EINVAL;
 	if (copy_from_sockptr(&tmp, arg, sizeof(tmp)) != 0)
 		return -EFAULT;
 
@@ -1512,6 +1534,8 @@
 		return -ENOMEM;
 	if (tmp.num_counters == 0)
 		return -EINVAL;
+	if ((u64)len < (u64)tmp.size + sizeof(tmp))
+		return -EINVAL;
 
 	tmp.name[sizeof(tmp.name)-1] = 0;
 
@@ -1751,6 +1775,10 @@
 
 	new_table = xt_register_table(net, table, &bootstrap, newinfo);
 	if (IS_ERR(new_table)) {
+		struct ip6t_entry *iter;
+
+		xt_entry_foreach(iter, loc_cpu_entry, newinfo->size)
+			cleanup_entry(iter, net);
 		xt_free_table_info(newinfo);
 		return PTR_ERR(new_table);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/ip6t_rpfilter.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/ip6t_rpfilter.c
@@ -37,8 +37,10 @@
 	bool ret = false;
 	struct flowi6 fl6 = {
 		.flowi6_iif = LOOPBACK_IFINDEX,
+		.flowi6_l3mdev = l3mdev_master_ifindex_rcu(dev),
 		.flowlabel = (* (__be32 *) iph) & IPV6_FLOWINFO_MASK,
 		.flowi6_proto = iph->nexthdr,
+		.flowi6_uid = sock_net_uid(net, NULL),
 		.daddr = iph->saddr,
 	};
 	int lookup_flags;
@@ -55,9 +57,7 @@
 	if (rpfilter_addr_linklocal(&iph->saddr)) {
 		lookup_flags |= RT6_LOOKUP_F_IFACE;
 		fl6.flowi6_oif = dev->ifindex;
-	/* Set flowi6_oif for vrf devices to lookup route in l3mdev domain. */
-	} else if (netif_is_l3_master(dev) || netif_is_l3_slave(dev) ||
-		  (flags & XT_RPFILTER_LOOSE) == 0)
+	} else if ((flags & XT_RPFILTER_LOOSE) == 0)
 		fl6.flowi6_oif = dev->ifindex;
 
 	rt = (void *)ip6_route_lookup(net, &fl6, skb, lookup_flags);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/ip6table_nat.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/ip6table_nat.c
@@ -154,23 +154,27 @@
 
 static int __init ip6table_nat_init(void)
 {
-	int ret = xt_register_template(&nf_nat_ipv6_table,
-				       ip6table_nat_table_init);
+	int ret;
 
+	/* net->gen->ptr[ip6table_nat_net_id] must be allocated
+	 * before calling ip6t_nat_register_lookups().
+	 */
+	ret = register_pernet_subsys(&ip6table_nat_net_ops);
 	if (ret < 0)
 		return ret;
 
-	ret = register_pernet_subsys(&ip6table_nat_net_ops);
+	ret = xt_register_template(&nf_nat_ipv6_table,
+				   ip6table_nat_table_init);
 	if (ret)
-		xt_unregister_template(&nf_nat_ipv6_table);
+		unregister_pernet_subsys(&ip6table_nat_net_ops);
 
 	return ret;
 }
 
 static void __exit ip6table_nat_exit(void)
 {
-	unregister_pernet_subsys(&ip6table_nat_net_ops);
 	xt_unregister_template(&nf_nat_ipv6_table);
+	unregister_pernet_subsys(&ip6table_nat_net_ops);
 }
 
 module_init(ip6table_nat_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/nf_conntrack_reasm.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/nf_conntrack_reasm.c
@@ -155,6 +155,10 @@
 	};
 	struct inet_frag_queue *q;
 
+	if (!(ipv6_addr_type(&hdr->daddr) & (IPV6_ADDR_MULTICAST |
+					    IPV6_ADDR_LINKLOCAL)))
+		key.iif = 0;
+
 	q = inet_frag_find(nf_frag->fqdir, &key);
 	if (!q)
 		return NULL;
@@ -293,6 +297,7 @@
 	}
 
 	skb_dst_drop(skb);
+	skb_orphan(skb);
 	return -EINPROGRESS;
 
 insert_error:
@@ -468,7 +473,6 @@
 	hdr = ipv6_hdr(skb);
 	fhdr = (struct frag_hdr *)skb_transport_header(skb);
 
-	skb_orphan(skb);
 	fq = fq_find(net, fhdr->identification, user, hdr,
 		     skb->dev ? skb->dev->ifindex : 0);
 	if (fq == NULL) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/nf_dup_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/nf_dup_ipv6.c
@@ -47,11 +47,12 @@
 void nf_dup_ipv6(struct net *net, struct sk_buff *skb, unsigned int hooknum,
 		 const struct in6_addr *gw, int oif)
 {
+	local_bh_disable();
 	if (this_cpu_read(nf_skb_duplicated))
-		return;
+		goto out;
 	skb = pskb_copy(skb, GFP_ATOMIC);
 	if (skb == NULL)
-		return;
+		goto out;
 
 #if IS_ENABLED(CONFIG_NF_CONNTRACK)
 	nf_reset_ct(skb);
@@ -69,6 +70,8 @@
 	} else {
 		kfree_skb(skb);
 	}
+out:
+	local_bh_enable();
 }
 EXPORT_SYMBOL_GPL(nf_dup_ipv6);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/nf_reject_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/nf_reject_ipv6.c
@@ -223,33 +223,23 @@
 			      const struct tcphdr *oth, unsigned int otcplen)
 {
 	struct tcphdr *tcph;
-	int needs_ack;
 
 	skb_reset_transport_header(nskb);
-	tcph = skb_put(nskb, sizeof(struct tcphdr));
+	tcph = skb_put_zero(nskb, sizeof(struct tcphdr));
 	/* Truncate to length (no data) */
 	tcph->doff = sizeof(struct tcphdr)/4;
 	tcph->source = oth->dest;
 	tcph->dest = oth->source;
 
 	if (oth->ack) {
-		needs_ack = 0;
 		tcph->seq = oth->ack_seq;
-		tcph->ack_seq = 0;
 	} else {
-		needs_ack = 1;
 		tcph->ack_seq = htonl(ntohl(oth->seq) + oth->syn + oth->fin +
 				      otcplen - (oth->doff<<2));
-		tcph->seq = 0;
+		tcph->ack = 1;
 	}
 
-	/* Reset flags */
-	((u_int8_t *)tcph)[13] = 0;
 	tcph->rst = 1;
-	tcph->ack = needs_ack;
-	tcph->window = 0;
-	tcph->urg_ptr = 0;
-	tcph->check = 0;
 
 	/* Adjust TCP checksum */
 	tcph->check = csum_ipv6_magic(&ipv6_hdr(nskb)->saddr,
@@ -279,13 +269,13 @@
 		    int hook)
 {
 	struct net_device *br_indev __maybe_unused;
-	struct sk_buff *nskb;
-	struct tcphdr _otcph;
-	const struct tcphdr *otcph;
-	unsigned int otcplen, hh_len;
 	const struct ipv6hdr *oip6h = ipv6_hdr(oldskb);
 	struct ipv6hdr *ip6h;
 	struct dst_entry *dst = NULL;
+	const struct tcphdr *otcph;
+	struct sk_buff *nskb;
+	struct tcphdr _otcph;
+	unsigned int otcplen;
 	struct flowi6 fl6;
 
 	if ((!(ipv6_addr_type(&oip6h->saddr) & IPV6_ADDR_UNICAST)) ||
@@ -324,9 +314,8 @@
 	if (IS_ERR(dst))
 		return;
 
-	hh_len = (dst->dev->hard_header_len + 15)&~15;
-	nskb = alloc_skb(hh_len + 15 + dst->header_len + sizeof(struct ipv6hdr)
-			 + sizeof(struct tcphdr) + dst->trailer_len,
+	nskb = alloc_skb(LL_MAX_HEADER + sizeof(struct ipv6hdr) +
+			 sizeof(struct tcphdr) + dst->trailer_len,
 			 GFP_ATOMIC);
 
 	if (!nskb) {
@@ -339,12 +328,13 @@
 
 	nskb->mark = fl6.flowi6_mark;
 
-	skb_reserve(nskb, hh_len + dst->header_len);
+	skb_reserve(nskb, LL_MAX_HEADER);
 	ip6h = nf_reject_ip6hdr_put(nskb, oldskb, IPPROTO_TCP,
 				    ip6_dst_hoplimit(dst));
 	nf_reject_ip6_tcphdr_put(nskb, oldskb, otcph, otcplen);
 
 	nf_ct_attach(nskb, oldskb);
+	nf_ct_set_closing(skb_nfct(oldskb));
 
 #if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
 	/* If we use ip6_local_out for bridged traffic, the MAC source on
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/nf_socket_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/nf_socket_ipv6.c
@@ -103,6 +103,10 @@
 	struct sk_buff *data_skb = NULL;
 	int doff = 0;
 	int thoff = 0, tproto;
+#if IS_ENABLED(CONFIG_NF_CONNTRACK)
+	enum ip_conntrack_info ctinfo;
+	struct nf_conn const *ct;
+#endif
 
 	tproto = ipv6_find_hdr(skb, &thoff, -1, NULL, NULL);
 	if (tproto < 0) {
@@ -136,6 +140,25 @@
 		return NULL;
 	}
 
+#if IS_ENABLED(CONFIG_NF_CONNTRACK)
+	/* Do the lookup with the original socket address in
+	 * case this is a reply packet of an established
+	 * SNAT-ted connection.
+	 */
+	ct = nf_ct_get(skb, &ctinfo);
+	if (ct &&
+	    ((tproto != IPPROTO_ICMPV6 &&
+	      ctinfo == IP_CT_ESTABLISHED_REPLY) ||
+	     (tproto == IPPROTO_ICMPV6 &&
+	      ctinfo == IP_CT_RELATED_REPLY)) &&
+	    (ct->status & IPS_SRC_NAT_DONE)) {
+		daddr = &ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple.src.u3.in6;
+		dport = (tproto == IPPROTO_TCP) ?
+			ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple.src.u.tcp.port :
+			ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple.src.u.udp.port;
+	}
+#endif
+
 	return nf_socket_get_sock_v6(net, data_skb, doff, tproto, saddr, daddr,
 				     sport, dport, indev);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/nf_tproxy_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/nf_tproxy_ipv6.c
@@ -63,7 +63,7 @@
 					    lport ? lport : hp->dest,
 					    skb->dev, NF_TPROXY_LOOKUP_LISTENER);
 		if (sk2) {
-			inet_twsk_deschedule_put(inet_twsk(sk));
+			nf_tproxy_twsk_deschedule_put(inet_twsk(sk));
 			sk = sk2;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/netfilter/nft_fib_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/netfilter/nft_fib_ipv6.c
@@ -60,6 +60,7 @@
 	struct flowi6 fl6 = {
 		.flowi6_iif = LOOPBACK_IFINDEX,
 		.flowi6_proto = pkt->tprot,
+		.flowi6_uid = sock_net_uid(nft_net(pkt), NULL),
 	};
 	u32 ret = 0;
 
@@ -68,6 +69,8 @@
 	else if (priv->flags & NFTA_FIB_F_OIF)
 		dev = nft_out(pkt);
 
+	fl6.flowi6_l3mdev = l3mdev_master_ifindex_rcu(dev);
+
 	nft_fib6_flowi_init(&fl6, priv, pkt, dev, iph);
 
 	if (dev && nf_ipv6_chk_addr(nft_net(pkt), &fl6.daddr, dev, true))
@@ -157,6 +160,8 @@
 	struct flowi6 fl6 = {
 		.flowi6_iif = LOOPBACK_IFINDEX,
 		.flowi6_proto = pkt->tprot,
+		.flowi6_uid = sock_net_uid(nft_net(pkt), NULL),
+		.flowi6_l3mdev = l3mdev_master_ifindex_rcu(nft_in(pkt)),
 	};
 	struct rt6_info *rt;
 	int lookup_flags;
@@ -193,7 +198,8 @@
 	if (rt->rt6i_flags & (RTF_REJECT | RTF_ANYCAST | RTF_LOCAL))
 		goto put_rt_err;
 
-	if (oif && oif != rt->rt6i_idev->dev)
+	if (oif && oif != rt->rt6i_idev->dev &&
+	    l3mdev_master_ifindex_rcu(rt->rt6i_idev->dev) != oif->ifindex)
 		goto put_rt_err;
 
 	nft_fib_store_result(dest, priv, rt->rt6i_idev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/ping.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/ping.c
@@ -96,7 +96,8 @@
 	addr_type = ipv6_addr_type(daddr);
 	if ((__ipv6_addr_needs_scope_id(addr_type) && !oif) ||
 	    (addr_type & IPV6_ADDR_MAPPED) ||
-	    (oif && sk->sk_bound_dev_if && oif != sk->sk_bound_dev_if))
+	    (oif && sk->sk_bound_dev_if && oif != sk->sk_bound_dev_if &&
+	     l3mdev_master_ifindex_by_index(sock_net(sk), oif) != sk->sk_bound_dev_if))
 		return -EINVAL;
 
 	/* TODO: use ip6_datagram_send_ctl to get options from cmsg */
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/raw.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/raw.c
@@ -539,6 +539,7 @@
 static int rawv6_push_pending_frames(struct sock *sk, struct flowi6 *fl6,
 				     struct raw6_sock *rp)
 {
+	struct ipv6_txoptions *opt;
 	struct sk_buff *skb;
 	int err = 0;
 	int offset;
@@ -556,6 +557,9 @@
 
 	offset = rp->offset;
 	total_len = inet_sk(sk)->cork.base.length;
+	opt = inet6_sk(sk)->cork.opt;
+	total_len -= opt ? opt->opt_flen : 0;
+
 	if (offset >= total_len - 1) {
 		err = -EINVAL;
 		ip6_flush_pending_frames(sk);
@@ -824,7 +828,8 @@
 
 		if (!proto)
 			proto = inet->inet_num;
-		else if (proto != inet->inet_num)
+		else if (proto != inet->inet_num &&
+			 inet->inet_num != IPPROTO_RAW)
 			return -EINVAL;
 
 		if (proto > 255)
@@ -1020,6 +1025,9 @@
 	struct raw6_sock *rp = raw6_sk(sk);
 	int val;
 
+	if (optlen < sizeof(val))
+		return -EINVAL;
+
 	if (copy_from_sockptr(&val, optval, sizeof(val)))
 		return -EFAULT;
 
@@ -1204,8 +1212,6 @@
 	lock_sock(sk);
 	ip6_flush_pending_frames(sk);
 	release_sock(sk);
-
-	inet6_destroy_sock(sk);
 }
 
 static int rawv6_init_sk(struct sock *sk)
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/reassembly.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/reassembly.c
@@ -363,7 +363,7 @@
 	 * the source of the fragment, with the Pointer field set to zero.
 	 */
 	nexthdr = hdr->nexthdr;
-	if (ipv6frag_thdr_truncated(skb, skb_transport_offset(skb), &nexthdr)) {
+	if (ipv6frag_thdr_truncated(skb, skb_network_offset(skb) + sizeof(struct ipv6hdr), &nexthdr)) {
 		__IP6_INC_STATS(net, __in6_dev_get_safely(skb->dev),
 				IPSTATS_MIB_INHDRERRORS);
 		icmpv6_param_prob(skb, ICMPV6_HDR_INCOMP, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/route.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/route.c
@@ -87,11 +87,12 @@
 static unsigned int	 ip6_default_advmss(const struct dst_entry *dst);
 INDIRECT_CALLABLE_SCOPE
 unsigned int		ip6_mtu(const struct dst_entry *dst);
-static struct dst_entry *ip6_negative_advice(struct dst_entry *);
+static void		ip6_negative_advice(struct sock *sk,
+					    struct dst_entry *dst);
 static void		ip6_dst_destroy(struct dst_entry *);
 static void		ip6_dst_ifdown(struct dst_entry *,
 				       struct net_device *dev, int how);
-static int		 ip6_dst_gc(struct dst_ops *ops);
+static void		 ip6_dst_gc(struct dst_ops *ops);
 
 static int		ip6_pkt_discard(struct sk_buff *skb);
 static int		ip6_pkt_discard_out(struct net *net, struct sock *sk, struct sk_buff *skb);
@@ -175,7 +176,7 @@
 			struct inet6_dev *rt_idev = rt->rt6i_idev;
 			struct net_device *rt_dev = rt->dst.dev;
 
-			if (rt_idev->dev == dev) {
+			if (rt_idev && rt_idev->dev == dev) {
 				rt->rt6i_idev = in6_dev_get(loopback_dev);
 				in6_dev_put(rt_idev);
 			}
@@ -633,6 +634,8 @@
 	rcu_read_lock_bh();
 	last_probe = READ_ONCE(fib6_nh->last_probe);
 	idev = __in6_dev_get(dev);
+	if (!idev)
+		goto out;
 	neigh = __ipv6_neigh_lookup_noref(dev, nh_gw);
 	if (neigh) {
 		if (neigh->nud_state & NUD_VALID)
@@ -1206,9 +1209,6 @@
 	struct fib6_node *fn;
 	struct rt6_info *rt;
 
-	if (fl6->flowi6_flags & FLOWI_FLAG_SKIP_NH_OIF)
-		flags &= ~RT6_LOOKUP_F_IFACE;
-
 	rcu_read_lock();
 	fn = fib6_node_lookup(&table->tb6_root, &fl6->daddr, &fl6->saddr);
 restart:
@@ -1397,6 +1397,7 @@
 		struct rt6_info *prev, **p;
 
 		p = this_cpu_ptr(res->nh->rt6i_pcpu);
+		/* Paired with READ_ONCE() in __fib6_drop_pcpu_from() */
 		prev = xchg(p, NULL);
 		if (prev) {
 			dst_dev_put(&prev->dst);
@@ -2178,9 +2179,6 @@
 	fn = fib6_node_lookup(&table->tb6_root, &fl6->daddr, &fl6->saddr);
 	saved_fn = fn;
 
-	if (fl6->flowi6_flags & FLOWI_FLAG_SKIP_NH_OIF)
-		oif = 0;
-
 redo_rt6_select:
 	rt6_select(net, fn, oif, res, strict);
 	if (res->f6i == net->ipv6.fib6_null_entry) {
@@ -2763,24 +2761,24 @@
 }
 EXPORT_INDIRECT_CALLABLE(ip6_dst_check);
 
-static struct dst_entry *ip6_negative_advice(struct dst_entry *dst)
+static void ip6_negative_advice(struct sock *sk,
+				struct dst_entry *dst)
 {
 	struct rt6_info *rt = (struct rt6_info *) dst;
 
-	if (rt) {
-		if (rt->rt6i_flags & RTF_CACHE) {
-			rcu_read_lock();
-			if (rt6_check_expired(rt)) {
-				rt6_remove_exception_rt(rt);
-				dst = NULL;
-			}
-			rcu_read_unlock();
-		} else {
-			dst_release(dst);
-			dst = NULL;
+	if (rt->rt6i_flags & RTF_CACHE) {
+		rcu_read_lock();
+		if (rt6_check_expired(rt)) {
+			/* rt/dst can not be destroyed yet,
+			 * because of rcu_read_lock()
+			 */
+			sk_dst_reset(sk);
+			rt6_remove_exception_rt(rt);
 		}
+		rcu_read_unlock();
+		return;
 	}
-	return dst;
+	sk_dst_reset(sk);
 }
 
 static void ip6_link_failure(struct sk_buff *skb)
@@ -2802,7 +2800,7 @@
 			if (from) {
 				fn = rcu_dereference(from->fib6_node);
 				if (fn && (rt->rt6i_flags & RTF_DEFAULT))
-					fn->fn_sernum = -1;
+					WRITE_ONCE(fn->fn_sernum, -1);
 			}
 		}
 		rcu_read_unlock();
@@ -3056,12 +3054,6 @@
 	struct fib6_info *rt;
 	struct fib6_node *fn;
 
-	/* l3mdev_update_flow overrides oif if the device is enslaved; in
-	 * this case we must match on the real ingress device, so reset it
-	 */
-	if (fl6->flowi6_flags & FLOWI_FLAG_SKIP_NH_OIF)
-		fl6->flowi6_oif = skb->dev->ifindex;
-
 	/* Get the "current" route for this destination and
 	 * check if the redirect has come from appropriate router.
 	 *
@@ -3192,13 +3184,18 @@
 {
 	struct net_device *dev = dst->dev;
 	unsigned int mtu = dst_mtu(dst);
-	struct net *net = dev_net(dev);
+	struct net *net;
 
 	mtu -= sizeof(struct ipv6hdr) + sizeof(struct tcphdr);
 
+	rcu_read_lock();
+
+	net = dev_net_rcu(dev);
 	if (mtu < net->ipv6.sysctl.ip6_rt_min_advmss)
 		mtu = net->ipv6.sysctl.ip6_rt_min_advmss;
 
+	rcu_read_unlock();
+
 	/*
 	 * Maximal non-jumbo IPv6 payload is IPV6_MAXPLEN and
 	 * corresponding MSS is IPV6_MAXPLEN - tcp_header_size.
@@ -3295,32 +3292,30 @@
 	return dst;
 }
 
-static int ip6_dst_gc(struct dst_ops *ops)
+static void ip6_dst_gc(struct dst_ops *ops)
 {
 	struct net *net = container_of(ops, struct net, ipv6.ip6_dst_ops);
 	int rt_min_interval = net->ipv6.sysctl.ip6_rt_gc_min_interval;
-	int rt_max_size = net->ipv6.sysctl.ip6_rt_max_size;
 	int rt_elasticity = net->ipv6.sysctl.ip6_rt_gc_elasticity;
 	int rt_gc_timeout = net->ipv6.sysctl.ip6_rt_gc_timeout;
 	unsigned long rt_last_gc = net->ipv6.ip6_rt_last_gc;
+	unsigned int val;
 	int entries;
 
 	entries = dst_entries_get_fast(ops);
-	if (entries > rt_max_size)
+	if (entries > ops->gc_thresh)
 		entries = dst_entries_get_slow(ops);
 
-	if (time_after(rt_last_gc + rt_min_interval, jiffies) &&
-	    entries <= rt_max_size)
+	if (time_after(rt_last_gc + rt_min_interval, jiffies))
 		goto out;
 
-	net->ipv6.ip6_rt_gc_expire++;
-	fib6_run_gc(net->ipv6.ip6_rt_gc_expire, net, true);
+	fib6_run_gc(atomic_inc_return(&net->ipv6.ip6_rt_gc_expire), net, true);
 	entries = dst_entries_get_slow(ops);
 	if (entries < ops->gc_thresh)
-		net->ipv6.ip6_rt_gc_expire = rt_gc_timeout>>1;
+		atomic_set(&net->ipv6.ip6_rt_gc_expire, rt_gc_timeout >> 1);
 out:
-	net->ipv6.ip6_rt_gc_expire -= net->ipv6.ip6_rt_gc_expire>>rt_elasticity;
-	return entries > rt_max_size;
+	val = atomic_read(&net->ipv6.ip6_rt_gc_expire);
+	atomic_set(&net->ipv6.ip6_rt_gc_expire, val - (val >> rt_elasticity));
 }
 
 static int ip6_nh_lookup_table(struct net *net, struct fib6_config *cfg,
@@ -3599,7 +3594,7 @@
 	if (!dev)
 		goto out;
 
-	if (idev->cnf.disable_ipv6) {
+	if (!idev || idev->cnf.disable_ipv6) {
 		NL_SET_ERR_MSG(extack, "IPv6 is disabled on nexthop device");
 		err = -EACCES;
 		goto out;
@@ -3635,7 +3630,8 @@
 		in6_dev_put(idev);
 
 	if (err) {
-		lwtstate_put(fib6_nh->fib_nh_lws);
+		fib_nh_common_release(&fib6_nh->nh_common);
+		fib6_nh->nh_common.nhc_pcpu_rth_output = NULL;
 		fib6_nh->fib_nh_lws = NULL;
 		dev_put(dev);
 	}
@@ -3680,6 +3676,25 @@
 	fib_nh_common_release(&fib6_nh->nh_common);
 }
 
+void fib6_nh_release_dsts(struct fib6_nh *fib6_nh)
+{
+	int cpu;
+
+	if (!fib6_nh->rt6i_pcpu)
+		return;
+
+	for_each_possible_cpu(cpu) {
+		struct rt6_info *pcpu_rt, **ppcpu_rt;
+
+		ppcpu_rt = per_cpu_ptr(fib6_nh->rt6i_pcpu, cpu);
+		pcpu_rt = xchg(ppcpu_rt, NULL);
+		if (pcpu_rt) {
+			dst_dev_put(&pcpu_rt->dst);
+			dst_release(&pcpu_rt->dst);
+		}
+	}
+}
+
 static struct fib6_info *ip6_route_info_create(struct fib6_config *cfg,
 					      gfp_t gfp_flags,
 					      struct netlink_ext_ack *extack)
@@ -3792,10 +3807,12 @@
 	if (nh) {
 		if (rt->fib6_src.plen) {
 			NL_SET_ERR_MSG(extack, "Nexthops can not be used with source routing");
+			err = -EINVAL;
 			goto out_free;
 		}
 		if (!nexthop_get(nh)) {
 			NL_SET_ERR_MSG(extack, "Nexthop has been deleted");
+			err = -ENOENT;
 			goto out_free;
 		}
 		rt->nh = nh;
@@ -4439,7 +4456,7 @@
 		.fc_table = l3mdev_fib_table_by_index(net, rtmsg->rtmsg_ifindex) ?
 			 : RT6_TABLE_MAIN,
 		.fc_ifindex = rtmsg->rtmsg_ifindex,
-		.fc_metric = rtmsg->rtmsg_metric ? : IP6_RT_PRIO_USER,
+		.fc_metric = rtmsg->rtmsg_metric,
 		.fc_expires = rtmsg->rtmsg_info,
 		.fc_dst_len = rtmsg->rtmsg_dst_len,
 		.fc_src_len = rtmsg->rtmsg_src_len,
@@ -4469,6 +4486,9 @@
 	rtnl_lock();
 	switch (cmd) {
 	case SIOCADDRT:
+		/* Only do the default setting of fc_metric in route adding */
+		if (cfg.fc_metric == 0)
+			cfg.fc_metric = IP6_RT_PRIO_USER;
 		err = ip6_route_add(&cfg, GFP_KERNEL, NULL);
 		break;
 	case SIOCDELRT:
@@ -4490,7 +4510,7 @@
 	struct inet6_dev *idev;
 	int type;
 
-	if (netif_is_l3_master(skb->dev) &&
+	if (netif_is_l3_master(skb->dev) ||
 	    dst->dev == net->loopback_dev)
 		idev = __in6_dev_get_safely(dev_get_by_index_rcu(net, IP6CB(skb)->iif));
 	else
@@ -4570,8 +4590,15 @@
 	}
 
 	f6i = ip6_route_info_create(&cfg, gfp_flags, NULL);
-	if (!IS_ERR(f6i))
+	if (!IS_ERR(f6i)) {
 		f6i->dst_nocount = true;
+
+		if (!anycast &&
+		    (net->ipv6.devconf_all->disable_policy ||
+		     idev->cnf.disable_policy))
+			f6i->dst_nopolicy = true;
+	}
+
 	return f6i;
 }
 
@@ -5205,6 +5232,19 @@
 	return should_notify;
 }
 
+static int fib6_gw_from_attr(struct in6_addr *gw, struct nlattr *nla,
+			     struct netlink_ext_ack *extack)
+{
+	if (nla_len(nla) < sizeof(*gw)) {
+		NL_SET_ERR_MSG(extack, "Invalid IPv6 address in RTA_GATEWAY");
+		return -EINVAL;
+	}
+
+	*gw = nla_get_in6_addr(nla);
+
+	return 0;
+}
+
 static int ip6_route_multipath_add(struct fib6_config *cfg,
 				   struct netlink_ext_ack *extack)
 {
@@ -5245,10 +5285,18 @@
 
 			nla = nla_find(attrs, attrlen, RTA_GATEWAY);
 			if (nla) {
-				r_cfg.fc_gateway = nla_get_in6_addr(nla);
+				err = fib6_gw_from_attr(&r_cfg.fc_gateway, nla,
+							extack);
+				if (err)
+					goto cleanup;
+
 				r_cfg.fc_flags |= RTF_GATEWAY;
 			}
 			r_cfg.fc_encap = nla_find(attrs, attrlen, RTA_ENCAP);
+
+			/* RTA_ENCAP_TYPE length checked in
+			 * lwtunnel_valid_encap_type_attr
+			 */
 			nla = nla_find(attrs, attrlen, RTA_ENCAP_TYPE);
 			if (nla)
 				r_cfg.fc_encap_type = nla_get_u16(nla);
@@ -5301,19 +5349,7 @@
 	err_nh = NULL;
 	list_for_each_entry(nh, &rt6_nh_list, next) {
 		err = __ip6_ins_rt(nh->fib6_info, info, extack);
-		fib6_info_release(nh->fib6_info);
-
-		if (!err) {
-			/* save reference to last route successfully inserted */
-			rt_last = nh->fib6_info;
 
-			/* save reference to first route for notification */
-			if (!rt_notif)
-				rt_notif = nh->fib6_info;
-		}
-
-		/* nh->fib6_info is used or freed at this point, reset to NULL*/
-		nh->fib6_info = NULL;
 		if (err) {
 			if (replace && nhn)
 				NL_SET_ERR_MSG_MOD(extack,
@@ -5321,6 +5357,12 @@
 			err_nh = nh;
 			goto add_errout;
 		}
+		/* save reference to last route successfully inserted */
+		rt_last = nh->fib6_info;
+
+		/* save reference to first route for notification */
+		if (!rt_notif)
+			rt_notif = nh->fib6_info;
 
 		/* Because each route is added like a single route we remove
 		 * these flags after the first nexthop: if there is a collision,
@@ -5381,8 +5423,7 @@
 
 cleanup:
 	list_for_each_entry_safe(nh, nh_safe, &rt6_nh_list, next) {
-		if (nh->fib6_info)
-			fib6_info_release(nh->fib6_info);
+		fib6_info_release(nh->fib6_info);
 		list_del(&nh->next);
 		kfree(nh);
 	}
@@ -5415,7 +5456,13 @@
 
 			nla = nla_find(attrs, attrlen, RTA_GATEWAY);
 			if (nla) {
-				nla_memcpy(&r_cfg.fc_gateway, nla, 16);
+				err = fib6_gw_from_attr(&r_cfg.fc_gateway, nla,
+							extack);
+				if (err) {
+					last_err = err;
+					goto next_rtnh;
+				}
+
 				r_cfg.fc_flags |= RTF_GATEWAY;
 			}
 		}
@@ -5423,6 +5470,7 @@
 		if (err)
 			last_err = err;
 
+next_rtnh:
 		rtnh = rtnh_next(rtnh, &remaining);
 	}
 
@@ -5500,16 +5548,17 @@
 		nexthop_for_each_fib6_nh(f6i->nh, rt6_nh_nlmsg_size,
 					 &nexthop_len);
 	} else {
+		struct fib6_info *sibling, *next_sibling;
 		struct fib6_nh *nh = f6i->fib6_nh;
 
 		nexthop_len = 0;
 		if (f6i->fib6_nsiblings) {
-			nexthop_len = nla_total_size(0)	 /* RTA_MULTIPATH */
-				    + NLA_ALIGN(sizeof(struct rtnexthop))
-				    + nla_total_size(16) /* RTA_GATEWAY */
-				    + lwtunnel_get_encap_size(nh->fib_nh_lws);
+			rt6_nh_nlmsg_size(nh, &nexthop_len);
 
-			nexthop_len *= f6i->fib6_nsiblings;
+			list_for_each_entry_safe(sibling, next_sibling,
+						 &f6i->fib6_siblings, fib6_siblings) {
+				rt6_nh_nlmsg_size(sibling->fib6_nh, &nexthop_len);
+			}
 		}
 		nexthop_len += lwtunnel_get_encap_size(nh->fib_nh_lws);
 	}
@@ -5701,7 +5750,7 @@
 		if (nexthop_is_blackhole(rt->nh))
 			rtm->rtm_type = RTN_BLACKHOLE;
 
-		if (net->ipv4.sysctl_nexthop_compat_mode &&
+		if (READ_ONCE(net->ipv4.sysctl_nexthop_compat_mode) &&
 		    rt6_fill_node_nexthop(skb, rt->nh, &nh_flags) < 0)
 			goto nla_put_failure;
 
@@ -5720,11 +5769,11 @@
 	}
 
 	if (!dst) {
-		if (rt->offload)
+		if (READ_ONCE(rt->offload))
 			rtm->rtm_flags |= RTM_F_OFFLOAD;
-		if (rt->trap)
+		if (READ_ONCE(rt->trap))
 			rtm->rtm_flags |= RTM_F_TRAP;
-		if (rt->offload_failed)
+		if (READ_ONCE(rt->offload_failed))
 			rtm->rtm_flags |= RTM_F_OFFLOAD_FAILED;
 	}
 
@@ -6182,19 +6231,20 @@
 	struct sk_buff *skb;
 	int err;
 
-	if (f6i->offload == offload && f6i->trap == trap &&
-	    f6i->offload_failed == offload_failed)
+	if (READ_ONCE(f6i->offload) == offload &&
+	    READ_ONCE(f6i->trap) == trap &&
+	    READ_ONCE(f6i->offload_failed) == offload_failed)
 		return;
 
-	f6i->offload = offload;
-	f6i->trap = trap;
+	WRITE_ONCE(f6i->offload, offload);
+	WRITE_ONCE(f6i->trap, trap);
 
 	/* 2 means send notifications only if offload_failed was changed. */
 	if (net->ipv6.sysctl.fib_notify_on_flag_change == 2 &&
-	    f6i->offload_failed == offload_failed)
+	    READ_ONCE(f6i->offload_failed) == offload_failed)
 		return;
 
-	f6i->offload_failed = offload_failed;
+	WRITE_ONCE(f6i->offload_failed, offload_failed);
 
 	if (!rcu_access_pointer(f6i->fib6_node))
 		/* The route was removed from the tree, do not send
@@ -6294,12 +6344,12 @@
 	if (!write)
 		return -EINVAL;
 
-	net = (struct net *)ctl->extra1;
-	delay = net->ipv6.sysctl.flush_delay;
 	ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
 	if (ret)
 		return ret;
 
+	net = (struct net *)ctl->extra1;
+	delay = net->ipv6.sysctl.flush_delay;
 	fib6_run_gc(delay <= 0 ? 0 : (unsigned long)delay, net, delay > 0);
 	return 0;
 }
@@ -6471,7 +6521,7 @@
 #endif
 
 	net->ipv6.sysctl.flush_delay = 0;
-	net->ipv6.sysctl.ip6_rt_max_size = 4096;
+	net->ipv6.sysctl.ip6_rt_max_size = INT_MAX;
 	net->ipv6.sysctl.ip6_rt_gc_min_interval = HZ / 2;
 	net->ipv6.sysctl.ip6_rt_gc_timeout = 60*HZ;
 	net->ipv6.sysctl.ip6_rt_gc_interval = 30*HZ;
@@ -6480,7 +6530,7 @@
 	net->ipv6.sysctl.ip6_rt_min_advmss = IPV6_MIN_MTU - 20 - 40;
 	net->ipv6.sysctl.skip_notify_on_dev_down = 0;
 
-	net->ipv6.ip6_rt_gc_expire = 30*HZ;
+	atomic_set(&net->ipv6.ip6_rt_gc_expire, 30*HZ);
 
 	ret = 0;
 out:
@@ -6514,10 +6564,16 @@
 static int __net_init ip6_route_net_init_late(struct net *net)
 {
 #ifdef CONFIG_PROC_FS
-	proc_create_net("ipv6_route", 0, net->proc_net, &ipv6_route_seq_ops,
-			sizeof(struct ipv6_route_iter));
-	proc_create_net_single("rt6_stats", 0444, net->proc_net,
-			rt6_stats_seq_show, NULL);
+	if (!proc_create_net("ipv6_route", 0, net->proc_net,
+			     &ipv6_route_seq_ops,
+			     sizeof(struct ipv6_route_iter)))
+		return -ENOMEM;
+
+	if (!proc_create_net_single("rt6_stats", 0444, net->proc_net,
+				    rt6_stats_seq_show, NULL)) {
+		remove_proc_entry("ipv6_route", net->proc_net);
+		return -ENOMEM;
+	}
 #endif
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/rpl.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/rpl.c
@@ -32,7 +32,8 @@
 size_t ipv6_rpl_srh_size(unsigned char n, unsigned char cmpri,
 			 unsigned char cmpre)
 {
-	return (n * IPV6_PFXTAIL_LEN(cmpri)) + IPV6_PFXTAIL_LEN(cmpre);
+	return sizeof(struct ipv6_rpl_sr_hdr) + (n * IPV6_PFXTAIL_LEN(cmpri)) +
+		IPV6_PFXTAIL_LEN(cmpre);
 }
 
 void ipv6_rpl_srh_decompress(struct ipv6_rpl_sr_hdr *outhdr,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/rpl_iptunnel.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/rpl_iptunnel.c
@@ -125,7 +125,8 @@
 }
 
 static int rpl_do_srh_inline(struct sk_buff *skb, const struct rpl_lwt *rlwt,
-			     const struct ipv6_rpl_sr_hdr *srh)
+			     const struct ipv6_rpl_sr_hdr *srh,
+			     struct dst_entry *cache_dst)
 {
 	struct ipv6_rpl_sr_hdr *isrh, *csrh;
 	const struct ipv6hdr *oldhdr;
@@ -153,7 +154,7 @@
 
 	hdrlen = ((csrh->hdrlen + 1) << 3);
 
-	err = skb_cow_head(skb, hdrlen + skb->mac_len);
+	err = skb_cow_head(skb, hdrlen + dst_dev_overhead(cache_dst, skb));
 	if (unlikely(err)) {
 		kfree(buf);
 		return err;
@@ -186,7 +187,8 @@
 	return 0;
 }
 
-static int rpl_do_srh(struct sk_buff *skb, const struct rpl_lwt *rlwt)
+static int rpl_do_srh(struct sk_buff *skb, const struct rpl_lwt *rlwt,
+		      struct dst_entry *cache_dst)
 {
 	struct dst_entry *dst = skb_dst(skb);
 	struct rpl_iptunnel_encap *tinfo;
@@ -196,7 +198,7 @@
 
 	tinfo = rpl_encap_lwtunnel(dst->lwtstate);
 
-	return rpl_do_srh_inline(skb, rlwt, tinfo->srh);
+	return rpl_do_srh_inline(skb, rlwt, tinfo->srh, cache_dst);
 }
 
 static int rpl_output(struct net *net, struct sock *sk, struct sk_buff *skb)
@@ -208,14 +210,14 @@
 
 	rlwt = rpl_lwt_lwtunnel(orig_dst->lwtstate);
 
-	err = rpl_do_srh(skb, rlwt);
+	local_bh_disable();
+	dst = dst_cache_get(&rlwt->cache);
+	local_bh_enable();
+
+	err = rpl_do_srh(skb, rlwt, dst);
 	if (unlikely(err))
 		goto drop;
 
-	preempt_disable();
-	dst = dst_cache_get(&rlwt->cache);
-	preempt_enable();
-
 	if (unlikely(!dst)) {
 		struct ipv6hdr *hdr = ipv6_hdr(skb);
 		struct flowi6 fl6;
@@ -230,25 +232,25 @@
 		dst = ip6_route_output(net, NULL, &fl6);
 		if (dst->error) {
 			err = dst->error;
-			dst_release(dst);
 			goto drop;
 		}
 
-		preempt_disable();
+		local_bh_disable();
 		dst_cache_set_ip6(&rlwt->cache, dst, &fl6.saddr);
-		preempt_enable();
+		local_bh_enable();
+
+		err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
+		if (unlikely(err))
+			goto drop;
 	}
 
 	skb_dst_drop(skb);
 	skb_dst_set(skb, dst);
 
-	err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
-	if (unlikely(err))
-		goto drop;
-
 	return dst_output(net, sk, skb);
 
 drop:
+	dst_release(dst);
 	kfree_skb(skb);
 	return err;
 }
@@ -257,41 +259,55 @@
 {
 	struct dst_entry *orig_dst = skb_dst(skb);
 	struct dst_entry *dst = NULL;
+	struct lwtunnel_state *lwtst;
 	struct rpl_lwt *rlwt;
 	int err;
 
-	rlwt = rpl_lwt_lwtunnel(orig_dst->lwtstate);
+	/* We cannot dereference "orig_dst" once ip6_route_input() or
+	 * skb_dst_drop() is called. However, in order to detect a dst loop, we
+	 * need the address of its lwtstate. So, save the address of lwtstate
+	 * now and use it later as a comparison.
+	 */
+	lwtst = orig_dst->lwtstate;
 
-	err = rpl_do_srh(skb, rlwt);
-	if (unlikely(err)) {
-		kfree_skb(skb);
-		return err;
-	}
+	rlwt = rpl_lwt_lwtunnel(lwtst);
 
-	preempt_disable();
+	local_bh_disable();
 	dst = dst_cache_get(&rlwt->cache);
-	preempt_enable();
+	local_bh_enable();
+
+	err = rpl_do_srh(skb, rlwt, dst);
+	if (unlikely(err)) {
+		dst_release(dst);
+		goto drop;
+	}
 
 	skb_dst_drop(skb);
 
 	if (!dst) {
 		ip6_route_input(skb);
 		dst = skb_dst(skb);
-		if (!dst->error) {
-			preempt_disable();
+
+		/* cache only if we don't create a dst reference loop */
+		if (!dst->error && lwtst != dst->lwtstate) {
+			local_bh_disable();
 			dst_cache_set_ip6(&rlwt->cache, dst,
 					  &ipv6_hdr(skb)->saddr);
-			preempt_enable();
+			local_bh_enable();
 		}
+
+		err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
+		if (unlikely(err))
+			goto drop;
 	} else {
 		skb_dst_set(skb, dst);
 	}
 
-	err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
-	if (unlikely(err))
-		return err;
-
 	return dst_input(skb);
+
+drop:
+	kfree_skb(skb);
+	return err;
 }
 
 static int nla_put_rpl_srh(struct sk_buff *skb, int attrtype,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/seg6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/seg6.c
@@ -75,6 +75,65 @@
 	return true;
 }
 
+struct ipv6_sr_hdr *seg6_get_srh(struct sk_buff *skb, int flags)
+{
+	struct ipv6_sr_hdr *srh;
+	int len, srhoff = 0;
+
+	if (ipv6_find_hdr(skb, &srhoff, IPPROTO_ROUTING, NULL, &flags) < 0)
+		return NULL;
+
+	if (!pskb_may_pull(skb, srhoff + sizeof(*srh)))
+		return NULL;
+
+	srh = (struct ipv6_sr_hdr *)(skb->data + srhoff);
+
+	len = (srh->hdrlen + 1) << 3;
+
+	if (!pskb_may_pull(skb, srhoff + len))
+		return NULL;
+
+	/* note that pskb_may_pull may change pointers in header;
+	 * for this reason it is necessary to reload them when needed.
+	 */
+	srh = (struct ipv6_sr_hdr *)(skb->data + srhoff);
+
+	if (!seg6_validate_srh(srh, len, true))
+		return NULL;
+
+	return srh;
+}
+
+/* Determine if an ICMP invoking packet contains a segment routing
+ * header.  If it does, extract the offset to the true destination
+ * address, which is in the first segment address.
+ */
+void seg6_icmp_srh(struct sk_buff *skb, struct inet6_skb_parm *opt)
+{
+	__u16 network_header = skb->network_header;
+	struct ipv6_sr_hdr *srh;
+
+	/* Update network header to point to the invoking packet
+	 * inside the ICMP packet, so we can use the seg6_get_srh()
+	 * helper.
+	 */
+	skb_reset_network_header(skb);
+
+	srh = seg6_get_srh(skb, 0);
+	if (!srh)
+		goto out;
+
+	if (srh->type != IPV6_SRCRT_TYPE_4)
+		goto out;
+
+	opt->flags |= IP6SKB_SEG6;
+	opt->srhoff = (unsigned char *)srh - skb->data;
+
+out:
+	/* Restore the network header back to the ICMP packet */
+	skb->network_header = network_header;
+}
+
 static struct genl_family seg6_genl_family;
 
 static const struct nla_policy seg6_genl_policy[SEG6_ATTR_MAX + 1] = {
@@ -132,6 +191,11 @@
 		goto out_unlock;
 	}
 
+	if (slen > nla_len(info->attrs[SEG6_ATTR_SECRET])) {
+		err = -EINVAL;
+		goto out_unlock;
+	}
+
 	if (hinfo) {
 		err = seg6_hmac_info_del(net, hmackeyid);
 		if (err)
@@ -443,22 +507,24 @@
 {
 	int err;
 
-	err = genl_register_family(&seg6_genl_family);
+	err = register_pernet_subsys(&ip6_segments_ops);
 	if (err)
 		goto out;
 
-	err = register_pernet_subsys(&ip6_segments_ops);
+	err = genl_register_family(&seg6_genl_family);
 	if (err)
-		goto out_unregister_genl;
+		goto out_unregister_pernet;
 
 #ifdef CONFIG_IPV6_SEG6_LWTUNNEL
 	err = seg6_iptunnel_init();
 	if (err)
-		goto out_unregister_pernet;
+		goto out_unregister_genl;
 
 	err = seg6_local_init();
-	if (err)
-		goto out_unregister_pernet;
+	if (err) {
+		seg6_iptunnel_exit();
+		goto out_unregister_genl;
+	}
 #endif
 
 #ifdef CONFIG_IPV6_SEG6_HMAC
@@ -479,11 +545,13 @@
 #endif
 #endif
 #ifdef CONFIG_IPV6_SEG6_LWTUNNEL
-out_unregister_pernet:
-	unregister_pernet_subsys(&ip6_segments_ops);
-#endif
 out_unregister_genl:
+#endif
+#if IS_ENABLED(CONFIG_IPV6_SEG6_LWTUNNEL) || IS_ENABLED(CONFIG_IPV6_SEG6_HMAC)
 	genl_unregister_family(&seg6_genl_family);
+#endif
+out_unregister_pernet:
+	unregister_pernet_subsys(&ip6_segments_ops);
 	goto out;
 }
 
@@ -493,8 +561,9 @@
 	seg6_hmac_exit();
 #endif
 #ifdef CONFIG_IPV6_SEG6_LWTUNNEL
+	seg6_local_exit();
 	seg6_iptunnel_exit();
 #endif
-	unregister_pernet_subsys(&ip6_segments_ops);
 	genl_unregister_family(&seg6_genl_family);
+	unregister_pernet_subsys(&ip6_segments_ops);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/seg6_hmac.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/seg6_hmac.c
@@ -354,6 +354,7 @@
 	struct crypto_shash *tfm;
 	struct shash_desc *shash;
 	int i, alg_count, cpu;
+	int ret = -ENOMEM;
 
 	alg_count = ARRAY_SIZE(hmac_algos);
 
@@ -364,12 +365,14 @@
 		algo = &hmac_algos[i];
 		algo->tfms = alloc_percpu(struct crypto_shash *);
 		if (!algo->tfms)
-			return -ENOMEM;
+			goto error_out;
 
 		for_each_possible_cpu(cpu) {
 			tfm = crypto_alloc_shash(algo->name, 0, 0);
-			if (IS_ERR(tfm))
-				return PTR_ERR(tfm);
+			if (IS_ERR(tfm)) {
+				ret = PTR_ERR(tfm);
+				goto error_out;
+			}
 			p_tfm = per_cpu_ptr(algo->tfms, cpu);
 			*p_tfm = tfm;
 		}
@@ -381,25 +384,28 @@
 
 		algo->shashs = alloc_percpu(struct shash_desc *);
 		if (!algo->shashs)
-			return -ENOMEM;
+			goto error_out;
 
 		for_each_possible_cpu(cpu) {
 			shash = kzalloc_node(shsize, GFP_KERNEL,
 					     cpu_to_node(cpu));
 			if (!shash)
-				return -ENOMEM;
+				goto error_out;
 			*per_cpu_ptr(algo->shashs, cpu) = shash;
 		}
 	}
 
 	return 0;
+
+error_out:
+	seg6_hmac_exit();
+	return ret;
 }
 
 int __init seg6_hmac_init(void)
 {
 	return seg6_hmac_init_algo();
 }
-EXPORT_SYMBOL(seg6_hmac_init);
 
 int __net_init seg6_hmac_net_init(struct net *net)
 {
@@ -409,27 +415,33 @@
 
 	return 0;
 }
-EXPORT_SYMBOL(seg6_hmac_net_init);
 
 void seg6_hmac_exit(void)
 {
 	struct seg6_hmac_algo *algo = NULL;
+	struct crypto_shash *tfm;
+	struct shash_desc *shash;
 	int i, alg_count, cpu;
 
 	alg_count = ARRAY_SIZE(hmac_algos);
 	for (i = 0; i < alg_count; i++) {
 		algo = &hmac_algos[i];
-		for_each_possible_cpu(cpu) {
-			struct crypto_shash *tfm;
-			struct shash_desc *shash;
 
-			shash = *per_cpu_ptr(algo->shashs, cpu);
-			kfree(shash);
-			tfm = *per_cpu_ptr(algo->tfms, cpu);
-			crypto_free_shash(tfm);
+		if (algo->shashs) {
+			for_each_possible_cpu(cpu) {
+				shash = *per_cpu_ptr(algo->shashs, cpu);
+				kfree(shash);
+			}
+			free_percpu(algo->shashs);
+		}
+
+		if (algo->tfms) {
+			for_each_possible_cpu(cpu) {
+				tfm = *per_cpu_ptr(algo->tfms, cpu);
+				crypto_free_shash(tfm);
+			}
+			free_percpu(algo->tfms);
 		}
-		free_percpu(algo->tfms);
-		free_percpu(algo->shashs);
 	}
 }
 EXPORT_SYMBOL(seg6_hmac_exit);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/seg6_iptunnel.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/seg6_iptunnel.c
@@ -36,9 +36,11 @@
 	case SEG6_IPTUN_MODE_INLINE:
 		break;
 	case SEG6_IPTUN_MODE_ENCAP:
+	case SEG6_IPTUN_MODE_ENCAP_RED:
 		head = sizeof(struct ipv6hdr);
 		break;
 	case SEG6_IPTUN_MODE_L2ENCAP:
+	case SEG6_IPTUN_MODE_L2ENCAP_RED:
 		return 0;
 	}
 
@@ -122,8 +124,8 @@
 	return flowlabel;
 }
 
-/* encapsulate an IPv6 packet within an outer IPv6 header with a given SRH */
-int seg6_do_srh_encap(struct sk_buff *skb, struct ipv6_sr_hdr *osrh, int proto)
+static int __seg6_do_srh_encap(struct sk_buff *skb, struct ipv6_sr_hdr *osrh,
+			       int proto, struct dst_entry *cache_dst)
 {
 	struct dst_entry *dst = skb_dst(skb);
 	struct net *net = dev_net(dst->dev);
@@ -135,7 +137,7 @@
 	hdrlen = (osrh->hdrlen + 1) << 3;
 	tot_len = hdrlen + sizeof(*hdr);
 
-	err = skb_cow_head(skb, tot_len + skb->mac_len);
+	err = skb_cow_head(skb, tot_len + dst_dev_overhead(cache_dst, skb));
 	if (unlikely(err))
 		return err;
 
@@ -161,6 +163,14 @@
 		hdr->hop_limit = ip6_dst_hoplimit(skb_dst(skb));
 
 		memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
+
+		/* the control block has been erased, so we have to set the
+		 * iif once again.
+		 * We read the receiving interface index directly from the
+		 * skb->skb_iif as it is done in the IPv4 receiving path (i.e.:
+		 * ip_rcv_core(...)).
+		 */
+		IP6CB(skb)->iif = skb->skb_iif;
 	}
 
 	hdr->nexthdr = NEXTHDR_ROUTING;
@@ -181,14 +191,141 @@
 	}
 #endif
 
+	hdr->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
+
 	skb_postpush_rcsum(skb, hdr, tot_len);
 
 	return 0;
 }
+
+/* encapsulate an IPv6 packet within an outer IPv6 header with a given SRH */
+int seg6_do_srh_encap(struct sk_buff *skb, struct ipv6_sr_hdr *osrh, int proto)
+{
+	return __seg6_do_srh_encap(skb, osrh, proto, NULL);
+}
 EXPORT_SYMBOL_GPL(seg6_do_srh_encap);
 
-/* insert an SRH within an IPv6 packet, just after the IPv6 header */
-int seg6_do_srh_inline(struct sk_buff *skb, struct ipv6_sr_hdr *osrh)
+/* encapsulate an IPv6 packet within an outer IPv6 header with reduced SRH */
+static int seg6_do_srh_encap_red(struct sk_buff *skb,
+				 struct ipv6_sr_hdr *osrh, int proto,
+				 struct dst_entry *cache_dst)
+{
+	__u8 first_seg = osrh->first_segment;
+	struct dst_entry *dst = skb_dst(skb);
+	struct net *net = dev_net(dst->dev);
+	struct ipv6hdr *hdr, *inner_hdr;
+	int hdrlen = ipv6_optlen(osrh);
+	int red_tlv_offset, tlv_offset;
+	struct ipv6_sr_hdr *isrh;
+	bool skip_srh = false;
+	__be32 flowlabel;
+	int tot_len, err;
+	int red_hdrlen;
+	int tlvs_len;
+
+	if (first_seg > 0) {
+		red_hdrlen = hdrlen - sizeof(struct in6_addr);
+	} else {
+		/* NOTE: if tag/flags and/or other TLVs are introduced in the
+		 * seg6_iptunnel infrastructure, they should be considered when
+		 * deciding to skip the SRH.
+		 */
+		skip_srh = !sr_has_hmac(osrh);
+
+		red_hdrlen = skip_srh ? 0 : hdrlen;
+	}
+
+	tot_len = red_hdrlen + sizeof(struct ipv6hdr);
+
+	err = skb_cow_head(skb, tot_len + dst_dev_overhead(cache_dst, skb));
+	if (unlikely(err))
+		return err;
+
+	inner_hdr = ipv6_hdr(skb);
+	flowlabel = seg6_make_flowlabel(net, skb, inner_hdr);
+
+	skb_push(skb, tot_len);
+	skb_reset_network_header(skb);
+	skb_mac_header_rebuild(skb);
+	hdr = ipv6_hdr(skb);
+
+	/* based on seg6_do_srh_encap() */
+	if (skb->protocol == htons(ETH_P_IPV6)) {
+		ip6_flow_hdr(hdr, ip6_tclass(ip6_flowinfo(inner_hdr)),
+			     flowlabel);
+		hdr->hop_limit = inner_hdr->hop_limit;
+	} else {
+		ip6_flow_hdr(hdr, 0, flowlabel);
+		hdr->hop_limit = ip6_dst_hoplimit(skb_dst(skb));
+
+		memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
+		IP6CB(skb)->iif = skb->skb_iif;
+	}
+
+	/* no matter if we have to skip the SRH or not, the first segment
+	 * always comes in the pushed IPv6 header.
+	 */
+	hdr->daddr = osrh->segments[first_seg];
+
+	if (skip_srh) {
+		hdr->nexthdr = proto;
+
+		set_tun_src(net, dst->dev, &hdr->daddr, &hdr->saddr);
+		goto out;
+	}
+
+	/* we cannot skip the SRH, slow path */
+
+	hdr->nexthdr = NEXTHDR_ROUTING;
+	isrh = (void *)hdr + sizeof(struct ipv6hdr);
+
+	if (unlikely(!first_seg)) {
+		/* this is a very rare case; we have only one SID but
+		 * we cannot skip the SRH since we are carrying some
+		 * other info.
+		 */
+		memcpy(isrh, osrh, hdrlen);
+		goto srcaddr;
+	}
+
+	tlv_offset = sizeof(*osrh) + (first_seg + 1) * sizeof(struct in6_addr);
+	red_tlv_offset = tlv_offset - sizeof(struct in6_addr);
+
+	memcpy(isrh, osrh, red_tlv_offset);
+
+	tlvs_len = hdrlen - tlv_offset;
+	if (unlikely(tlvs_len > 0)) {
+		const void *s = (const void *)osrh + tlv_offset;
+		void *d = (void *)isrh + red_tlv_offset;
+
+		memcpy(d, s, tlvs_len);
+	}
+
+	--isrh->first_segment;
+	isrh->hdrlen -= 2;
+
+srcaddr:
+	isrh->nexthdr = proto;
+	set_tun_src(net, dst->dev, &hdr->daddr, &hdr->saddr);
+
+#ifdef CONFIG_IPV6_SEG6_HMAC
+	if (unlikely(!skip_srh && sr_has_hmac(isrh))) {
+		err = seg6_push_hmac(net, &hdr->saddr, isrh);
+		if (unlikely(err))
+			return err;
+	}
+#endif
+
+out:
+	hdr->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
+
+	skb_postpush_rcsum(skb, hdr, tot_len);
+
+	return 0;
+}
+
+static int __seg6_do_srh_inline(struct sk_buff *skb, struct ipv6_sr_hdr *osrh,
+				struct dst_entry *cache_dst)
 {
 	struct ipv6hdr *hdr, *oldhdr;
 	struct ipv6_sr_hdr *isrh;
@@ -196,7 +333,7 @@
 
 	hdrlen = (osrh->hdrlen + 1) << 3;
 
-	err = skb_cow_head(skb, hdrlen + skb->mac_len);
+	err = skb_cow_head(skb, hdrlen + dst_dev_overhead(cache_dst, skb));
 	if (unlikely(err))
 		return err;
 
@@ -233,13 +370,14 @@
 	}
 #endif
 
+	hdr->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
+
 	skb_postpush_rcsum(skb, hdr, sizeof(struct ipv6hdr) + hdrlen);
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(seg6_do_srh_inline);
 
-static int seg6_do_srh(struct sk_buff *skb)
+static int seg6_do_srh(struct sk_buff *skb, struct dst_entry *cache_dst)
 {
 	struct dst_entry *dst = skb_dst(skb);
 	struct seg6_iptunnel_encap *tinfo;
@@ -252,11 +390,12 @@
 		if (skb->protocol != htons(ETH_P_IPV6))
 			return -EINVAL;
 
-		err = seg6_do_srh_inline(skb, tinfo->srh);
+		err = __seg6_do_srh_inline(skb, tinfo->srh, cache_dst);
 		if (err)
 			return err;
 		break;
 	case SEG6_IPTUN_MODE_ENCAP:
+	case SEG6_IPTUN_MODE_ENCAP_RED:
 		err = iptunnel_handle_offloads(skb, SKB_GSO_IPXIP6);
 		if (err)
 			return err;
@@ -268,7 +407,13 @@
 		else
 			return -EINVAL;
 
-		err = seg6_do_srh_encap(skb, tinfo->srh, proto);
+		if (tinfo->mode == SEG6_IPTUN_MODE_ENCAP)
+			err = __seg6_do_srh_encap(skb, tinfo->srh,
+						  proto, cache_dst);
+		else
+			err = seg6_do_srh_encap_red(skb, tinfo->srh,
+						    proto, cache_dst);
+
 		if (err)
 			return err;
 
@@ -277,6 +422,7 @@
 		skb->protocol = htons(ETH_P_IPV6);
 		break;
 	case SEG6_IPTUN_MODE_L2ENCAP:
+	case SEG6_IPTUN_MODE_L2ENCAP_RED:
 		if (!skb_mac_header_was_set(skb))
 			return -EINVAL;
 
@@ -286,7 +432,15 @@
 		skb_mac_header_rebuild(skb);
 		skb_push(skb, skb->mac_len);
 
-		err = seg6_do_srh_encap(skb, tinfo->srh, IPPROTO_ETHERNET);
+		if (tinfo->mode == SEG6_IPTUN_MODE_L2ENCAP)
+			err = __seg6_do_srh_encap(skb, tinfo->srh,
+						  IPPROTO_ETHERNET,
+						  cache_dst);
+		else
+			err = seg6_do_srh_encap_red(skb, tinfo->srh,
+						    IPPROTO_ETHERNET,
+						    cache_dst);
+
 		if (err)
 			return err;
 
@@ -294,13 +448,19 @@
 		break;
 	}
 
-	ipv6_hdr(skb)->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
 	skb_set_transport_header(skb, sizeof(struct ipv6hdr));
 	nf_reset_ct(skb);
 
 	return 0;
 }
 
+/* insert an SRH within an IPv6 packet, just after the IPv6 header */
+int seg6_do_srh_inline(struct sk_buff *skb, struct ipv6_sr_hdr *osrh)
+{
+	return __seg6_do_srh_inline(skb, osrh, NULL);
+}
+EXPORT_SYMBOL_GPL(seg6_do_srh_inline);
+
 static int seg6_input_finish(struct net *net, struct sock *sk,
 			     struct sk_buff *skb)
 {
@@ -312,46 +472,59 @@
 {
 	struct dst_entry *orig_dst = skb_dst(skb);
 	struct dst_entry *dst = NULL;
+	struct lwtunnel_state *lwtst;
 	struct seg6_lwt *slwt;
 	int err;
 
-	err = seg6_do_srh(skb);
-	if (unlikely(err)) {
-		kfree_skb(skb);
-		return err;
-	}
+	/* We cannot dereference "orig_dst" once ip6_route_input() or
+	 * skb_dst_drop() is called. However, in order to detect a dst loop, we
+	 * need the address of its lwtstate. So, save the address of lwtstate
+	 * now and use it later as a comparison.
+	 */
+	lwtst = orig_dst->lwtstate;
 
-	slwt = seg6_lwt_lwtunnel(orig_dst->lwtstate);
+	slwt = seg6_lwt_lwtunnel(lwtst);
 
-	preempt_disable();
+	local_bh_disable();
 	dst = dst_cache_get(&slwt->cache);
-	preempt_enable();
+	local_bh_enable();
+
+	err = seg6_do_srh(skb, dst);
+	if (unlikely(err)) {
+		dst_release(dst);
+		goto drop;
+	}
 
 	skb_dst_drop(skb);
 
 	if (!dst) {
 		ip6_route_input(skb);
 		dst = skb_dst(skb);
-		if (!dst->error) {
-			preempt_disable();
+
+		/* cache only if we don't create a dst reference loop */
+		if (!dst->error && lwtst != dst->lwtstate) {
+			local_bh_disable();
 			dst_cache_set_ip6(&slwt->cache, dst,
 					  &ipv6_hdr(skb)->saddr);
-			preempt_enable();
+			local_bh_enable();
 		}
+
+		err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
+		if (unlikely(err))
+			goto drop;
 	} else {
 		skb_dst_set(skb, dst);
 	}
 
-	err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
-	if (unlikely(err))
-		return err;
-
 	if (static_branch_unlikely(&nf_hooks_lwtunnel_enabled))
 		return NF_HOOK(NFPROTO_IPV6, NF_INET_LOCAL_OUT,
 			       dev_net(skb->dev), NULL, skb, NULL,
 			       skb_dst(skb)->dev, seg6_input_finish);
 
 	return seg6_input_finish(dev_net(skb->dev), NULL, skb);
+drop:
+	kfree_skb(skb);
+	return err;
 }
 
 static int seg6_input_nf(struct sk_buff *skb)
@@ -387,15 +560,15 @@
 	struct seg6_lwt *slwt;
 	int err;
 
-	err = seg6_do_srh(skb);
-	if (unlikely(err))
-		goto drop;
-
 	slwt = seg6_lwt_lwtunnel(orig_dst->lwtstate);
 
-	preempt_disable();
+	local_bh_disable();
 	dst = dst_cache_get(&slwt->cache);
-	preempt_enable();
+	local_bh_enable();
+
+	err = seg6_do_srh(skb, dst);
+	if (unlikely(err))
+		goto drop;
 
 	if (unlikely(!dst)) {
 		struct ipv6hdr *hdr = ipv6_hdr(skb);
@@ -411,28 +584,28 @@
 		dst = ip6_route_output(net, NULL, &fl6);
 		if (dst->error) {
 			err = dst->error;
-			dst_release(dst);
 			goto drop;
 		}
 
-		preempt_disable();
+		local_bh_disable();
 		dst_cache_set_ip6(&slwt->cache, dst, &fl6.saddr);
-		preempt_enable();
+		local_bh_enable();
+
+		err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
+		if (unlikely(err))
+			goto drop;
 	}
 
 	skb_dst_drop(skb);
 	skb_dst_set(skb, dst);
 
-	err = skb_cow_head(skb, LL_RESERVED_SPACE(dst->dev));
-	if (unlikely(err))
-		goto drop;
-
 	if (static_branch_unlikely(&nf_hooks_lwtunnel_enabled))
 		return NF_HOOK(NFPROTO_IPV6, NF_INET_LOCAL_OUT, net, sk, skb,
 			       NULL, skb_dst(skb)->dev, dst_output);
 
 	return dst_output(net, sk, skb);
 drop:
+	dst_release(dst);
 	kfree_skb(skb);
 	return err;
 }
@@ -506,6 +679,10 @@
 		break;
 	case SEG6_IPTUN_MODE_L2ENCAP:
 		break;
+	case SEG6_IPTUN_MODE_ENCAP_RED:
+		break;
+	case SEG6_IPTUN_MODE_L2ENCAP_RED:
+		break;
 	default:
 		return -EINVAL;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/seg6_local.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/seg6_local.c
@@ -150,40 +150,11 @@
 	return (struct seg6_local_lwt *)lwt->data;
 }
 
-static struct ipv6_sr_hdr *get_srh(struct sk_buff *skb, int flags)
-{
-	struct ipv6_sr_hdr *srh;
-	int len, srhoff = 0;
-
-	if (ipv6_find_hdr(skb, &srhoff, IPPROTO_ROUTING, NULL, &flags) < 0)
-		return NULL;
-
-	if (!pskb_may_pull(skb, srhoff + sizeof(*srh)))
-		return NULL;
-
-	srh = (struct ipv6_sr_hdr *)(skb->data + srhoff);
-
-	len = (srh->hdrlen + 1) << 3;
-
-	if (!pskb_may_pull(skb, srhoff + len))
-		return NULL;
-
-	/* note that pskb_may_pull may change pointers in header;
-	 * for this reason it is necessary to reload them when needed.
-	 */
-	srh = (struct ipv6_sr_hdr *)(skb->data + srhoff);
-
-	if (!seg6_validate_srh(srh, len, true))
-		return NULL;
-
-	return srh;
-}
-
 static struct ipv6_sr_hdr *get_and_validate_srh(struct sk_buff *skb)
 {
 	struct ipv6_sr_hdr *srh;
 
-	srh = get_srh(skb, IP6_FH_F_SKIP_RH);
+	srh = seg6_get_srh(skb, IP6_FH_F_SKIP_RH);
 	if (!srh)
 		return NULL;
 
@@ -200,7 +171,7 @@
 	struct ipv6_sr_hdr *srh;
 	unsigned int off = 0;
 
-	srh = get_srh(skb, 0);
+	srh = seg6_get_srh(skb, 0);
 	if (srh && srh->segments_left > 0)
 		return false;
 
@@ -246,6 +217,7 @@
 	struct flowi6 fl6;
 	int dev_flags = 0;
 
+	memset(&fl6, 0, sizeof(fl6));
 	fl6.flowi6_iif = skb->dev->ifindex;
 	fl6.daddr = nhaddr ? *nhaddr : hdr->daddr;
 	fl6.saddr = hdr->saddr;
@@ -456,8 +428,8 @@
 
 	if (static_branch_unlikely(&nf_hooks_lwtunnel_enabled))
 		return NF_HOOK(NFPROTO_IPV6, NF_INET_PRE_ROUTING,
-			       dev_net(skb->dev), NULL, skb, NULL,
-			       skb_dst(skb)->dev, input_action_end_dx6_finish);
+			       dev_net(skb->dev), NULL, skb, skb->dev,
+			       NULL, input_action_end_dx6_finish);
 
 	return input_action_end_dx6_finish(dev_net(skb->dev), NULL, skb);
 drop:
@@ -506,8 +478,8 @@
 
 	if (static_branch_unlikely(&nf_hooks_lwtunnel_enabled))
 		return NF_HOOK(NFPROTO_IPV4, NF_INET_PRE_ROUTING,
-			       dev_net(skb->dev), NULL, skb, NULL,
-			       skb_dst(skb)->dev, input_action_end_dx4_finish);
+			       dev_net(skb->dev), NULL, skb, skb->dev,
+			       NULL, input_action_end_dx4_finish);
 
 	return input_action_end_dx4_finish(dev_net(skb->dev), NULL, skb);
 drop:
@@ -853,7 +825,6 @@
 	if (err)
 		goto drop;
 
-	ipv6_hdr(skb)->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
 	skb_set_transport_header(skb, sizeof(struct ipv6hdr));
 
 	seg6_lookup_nexthop(skb, NULL, 0);
@@ -885,7 +856,6 @@
 	if (err)
 		goto drop;
 
-	ipv6_hdr(skb)->payload_len = htons(skb->len - sizeof(struct ipv6hdr));
 	skb_set_transport_header(skb, sizeof(struct ipv6hdr));
 
 	seg6_lookup_nexthop(skb, NULL, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/sit.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/sit.c
@@ -323,8 +323,6 @@
 		kcalloc(cmax, sizeof(*kp), GFP_KERNEL_ACCOUNT | __GFP_NOWARN) :
 		NULL;
 
-	rcu_read_lock();
-
 	ca = min(t->prl_count, cmax);
 
 	if (!kp) {
@@ -341,7 +339,7 @@
 		}
 	}
 
-	c = 0;
+	rcu_read_lock();
 	for_each_prl_rcu(t->prl) {
 		if (c >= cmax)
 			break;
@@ -353,7 +351,7 @@
 		if (kprl.addr != htonl(INADDR_ANY))
 			break;
 	}
-out:
+
 	rcu_read_unlock();
 
 	len = sizeof(*kp) * c;
@@ -362,7 +360,7 @@
 		ret = -EFAULT;
 
 	kfree(kp);
-
+out:
 	return ret;
 }
 
@@ -698,7 +696,7 @@
 		skb->dev = tunnel->dev;
 
 		if (packet_is_spoofed(skb, iph, tunnel)) {
-			tunnel->dev->stats.rx_errors++;
+			DEV_STATS_INC(tunnel->dev, rx_errors);
 			goto out;
 		}
 
@@ -718,8 +716,8 @@
 				net_info_ratelimited("non-ECT from %pI4 with TOS=%#x\n",
 						     &iph->saddr, iph->tos);
 			if (err > 1) {
-				++tunnel->dev->stats.rx_frame_errors;
-				++tunnel->dev->stats.rx_errors;
+				DEV_STATS_INC(tunnel->dev, rx_frame_errors);
+				DEV_STATS_INC(tunnel->dev, rx_errors);
 				goto out;
 			}
 		}
@@ -950,7 +948,7 @@
 	if (!rt) {
 		rt = ip_route_output_flow(tunnel->net, &fl4, NULL);
 		if (IS_ERR(rt)) {
-			dev->stats.tx_carrier_errors++;
+			DEV_STATS_INC(dev, tx_carrier_errors);
 			goto tx_error_icmp;
 		}
 		dst_cache_set_ip4(&tunnel->dst_cache, &rt->dst, fl4.saddr);
@@ -958,14 +956,14 @@
 
 	if (rt->rt_type != RTN_UNICAST) {
 		ip_rt_put(rt);
-		dev->stats.tx_carrier_errors++;
+		DEV_STATS_INC(dev, tx_carrier_errors);
 		goto tx_error_icmp;
 	}
 	tdev = rt->dst.dev;
 
 	if (tdev == dev) {
 		ip_rt_put(rt);
-		dev->stats.collisions++;
+		DEV_STATS_INC(dev, collisions);
 		goto tx_error;
 	}
 
@@ -978,7 +976,7 @@
 		mtu = dst_mtu(&rt->dst) - t_hlen;
 
 		if (mtu < IPV4_MIN_MTU) {
-			dev->stats.collisions++;
+			DEV_STATS_INC(dev, collisions);
 			ip_rt_put(rt);
 			goto tx_error;
 		}
@@ -1017,7 +1015,7 @@
 		struct sk_buff *new_skb = skb_realloc_headroom(skb, max_headroom);
 		if (!new_skb) {
 			ip_rt_put(rt);
-			dev->stats.tx_dropped++;
+			DEV_STATS_INC(dev, tx_dropped);
 			kfree_skb(skb);
 			return NETDEV_TX_OK;
 		}
@@ -1047,7 +1045,7 @@
 	dst_link_failure(skb);
 tx_error:
 	kfree_skb(skb);
-	dev->stats.tx_errors++;
+	DEV_STATS_INC(dev, tx_errors);
 	return NETDEV_TX_OK;
 }
 
@@ -1066,7 +1064,7 @@
 	return NETDEV_TX_OK;
 tx_error:
 	kfree_skb(skb);
-	dev->stats.tx_errors++;
+	DEV_STATS_INC(dev, tx_errors);
 	return NETDEV_TX_OK;
 }
 
@@ -1095,7 +1093,7 @@
 	return NETDEV_TX_OK;
 
 tx_err:
-	dev->stats.tx_errors++;
+	DEV_STATS_INC(dev, tx_errors);
 	kfree_skb(skb);
 	return NETDEV_TX_OK;
 
@@ -1103,12 +1101,13 @@
 
 static void ipip6_tunnel_bind_dev(struct net_device *dev)
 {
+	struct ip_tunnel *tunnel = netdev_priv(dev);
+	int t_hlen = tunnel->hlen + sizeof(struct iphdr);
 	struct net_device *tdev = NULL;
-	struct ip_tunnel *tunnel;
+	int hlen = LL_MAX_HEADER;
 	const struct iphdr *iph;
 	struct flowi4 fl4;
 
-	tunnel = netdev_priv(dev);
 	iph = &tunnel->parms.iph;
 
 	if (iph->daddr) {
@@ -1131,12 +1130,15 @@
 		tdev = __dev_get_by_index(tunnel->net, tunnel->parms.link);
 
 	if (tdev && !netif_is_l3_master(tdev)) {
-		int t_hlen = tunnel->hlen + sizeof(struct iphdr);
+		int mtu;
 
-		dev->mtu = tdev->mtu - t_hlen;
-		if (dev->mtu < IPV6_MIN_MTU)
-			dev->mtu = IPV6_MIN_MTU;
+		mtu = tdev->mtu - t_hlen;
+		if (mtu < IPV6_MIN_MTU)
+			mtu = IPV6_MIN_MTU;
+		WRITE_ONCE(dev->mtu, mtu);
+		hlen = tdev->hard_header_len + tdev->needed_headroom;
 	}
+	dev->needed_headroom = t_hlen + hlen;
 }
 
 static void ipip6_tunnel_update(struct ip_tunnel *t, struct ip_tunnel_parm *p,
@@ -1933,7 +1935,6 @@
 	return 0;
 
 err_reg_dev:
-	ipip6_dev_free(sitn->fb_tunnel_dev);
 	free_netdev(sitn->fb_tunnel_dev);
 err_alloc_dev:
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/syncookies.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/syncookies.c
@@ -141,7 +141,8 @@
 	__u8 rcv_wscale;
 	u32 tsoff = 0;
 
-	if (!sock_net(sk)->ipv4.sysctl_tcp_syncookies || !th->ack || th->rst)
+	if (!READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_syncookies) ||
+	    !th->ack || th->rst)
 		goto out;
 
 	if (tcp_synq_no_recent_overflow(sk))
@@ -170,7 +171,8 @@
 		goto out;
 
 	ret = NULL;
-	req = cookie_tcp_reqsk_alloc(&tcp6_request_sock_ops, sk, skb);
+	req = cookie_tcp_reqsk_alloc(&tcp6_request_sock_ops,
+				     &tcp_request_sock_ipv6_ops, sk, skb);
 	if (!req)
 		goto out;
 
@@ -178,14 +180,15 @@
 	treq = tcp_rsk(req);
 	treq->tfo_listener = false;
 
-	if (security_inet_conn_request(sk, skb, req))
-		goto out_free;
-
 	req->mss = mss;
 	ireq->ir_rmt_port = th->source;
 	ireq->ir_num = ntohs(th->dest);
 	ireq->ir_v6_rmt_addr = ipv6_hdr(skb)->saddr;
 	ireq->ir_v6_loc_addr = ipv6_hdr(skb)->daddr;
+
+	if (security_inet_conn_request(sk, skb, req))
+		goto out_free;
+
 	if (ipv6_opt_accepted(sk, skb, &TCP_SKB_CB(skb)->header.h6) ||
 	    np->rxopt.bits.rxinfo || np->rxopt.bits.rxoinfo ||
 	    np->rxopt.bits.rxhlim || np->rxopt.bits.rxohlim) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/tcp_ipv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/tcp_ipv6.c
@@ -107,9 +107,9 @@
 	if (dst && dst_hold_safe(dst)) {
 		const struct rt6_info *rt = (const struct rt6_info *)dst;
 
-		sk->sk_rx_dst = dst;
-		inet_sk(sk)->rx_dst_ifindex = skb->skb_iif;
-		tcp_inet6_sk(sk)->rx_dst_cookie = rt6_get_cookie(rt);
+		rcu_assign_pointer(sk->sk_rx_dst, dst);
+		sk->sk_rx_dst_ifindex = skb->skb_iif;
+		sk->sk_rx_dst_cookie = rt6_get_cookie(rt);
 	}
 }
 
@@ -237,7 +237,8 @@
 		sin.sin_port = usin->sin6_port;
 		sin.sin_addr.s_addr = usin->sin6_addr.s6_addr32[3];
 
-		icsk->icsk_af_ops = &ipv6_mapped;
+		/* Paired with READ_ONCE() in tcp_(get|set)sockopt() */
+		WRITE_ONCE(icsk->icsk_af_ops, &ipv6_mapped);
 		if (sk_is_mptcp(sk))
 			mptcpv6_handle_mapped(sk, true);
 		sk->sk_backlog_rcv = tcp_v4_do_rcv;
@@ -249,7 +250,8 @@
 
 		if (err) {
 			icsk->icsk_ext_hdr_len = exthdrlen;
-			icsk->icsk_af_ops = &ipv6_specific;
+			/* Paired with READ_ONCE() in tcp_(get|set)sockopt() */
+			WRITE_ONCE(icsk->icsk_af_ops, &ipv6_specific);
 			if (sk_is_mptcp(sk))
 				mptcpv6_handle_mapped(sk, false);
 			sk->sk_backlog_rcv = tcp_v6_do_rcv;
@@ -269,6 +271,7 @@
 	fl6.flowi6_proto = IPPROTO_TCP;
 	fl6.daddr = sk->sk_v6_daddr;
 	fl6.saddr = saddr ? *saddr : np->saddr;
+	fl6.flowlabel = ip6_make_flowinfo(np->tclass, np->flow_label);
 	fl6.flowi6_oif = sk->sk_bound_dev_if;
 	fl6.flowi6_mark = sk->sk_mark;
 	fl6.fl6_dport = usin->sin6_port;
@@ -339,6 +342,8 @@
 
 late_failure:
 	tcp_set_state(sk, TCP_CLOSE);
+	if (!(sk->sk_userlocks & SOCK_BINDADDR_LOCK))
+		inet_reset_saddr(sk);
 failure:
 	inet->inet_dport = 0;
 	sk->sk_route_caps = 0;
@@ -480,13 +485,10 @@
 
 		ipv6_icmp_error(sk, skb, err, th->dest, ntohl(info), (u8 *)th);
 
-		if (!sock_owned_by_user(sk)) {
-			sk->sk_err = err;
-			sk_error_report(sk);		/* Wake people up to see the error (see connect in sock.c) */
-
-			tcp_done(sk);
-		} else
-			sk->sk_err_soft = err;
+		if (!sock_owned_by_user(sk))
+			tcp_done_with_error(sk, err);
+		else
+			WRITE_ONCE(sk->sk_err_soft, err);
 		goto out;
 	case TCP_LISTEN:
 		break;
@@ -500,11 +502,11 @@
 	}
 
 	if (!sock_owned_by_user(sk) && np->recverr) {
-		sk->sk_err = err;
+		WRITE_ONCE(sk->sk_err, err);
 		sk_error_report(sk);
-	} else
-		sk->sk_err_soft = err;
-
+	} else {
+		WRITE_ONCE(sk->sk_err_soft, err);
+	}
 out:
 	bh_unlock_sock(sk);
 	sock_put(sk);
@@ -542,7 +544,7 @@
 		if (np->repflow && ireq->pktopts)
 			fl6->flowlabel = ip6_flowlabel(ipv6_hdr(ireq->pktopts));
 
-		tclass = sock_net(sk)->ipv4.sysctl_tcp_reflect_tos ?
+		tclass = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_reflect_tos) ?
 				(tcp_rsk(req)->syn_tos & ~INET_ECN_MASK) |
 				(np->tclass & INET_ECN_MASK) :
 				np->tclass;
@@ -1001,7 +1003,10 @@
 	 * Underlying function will use this to retrieve the network
 	 * namespace
 	 */
-	dst = ip6_dst_lookup_flow(sock_net(ctl_sk), ctl_sk, &fl6, NULL);
+	if (sk && sk->sk_state != TCP_TIME_WAIT)
+		dst = ip6_dst_lookup_flow(net, sk, &fl6, NULL); /*sk's xfrm_policy can be referred*/
+	else
+		dst = ip6_dst_lookup_flow(net, ctl_sk, &fl6, NULL);
 	if (!IS_ERR(dst)) {
 		skb_dst_set(buff, dst);
 		ip6_xmit(ctl_sk, buff, &fl6, fl6.flowi6_mark, NULL,
@@ -1165,7 +1170,7 @@
 			tcp_rsk(req)->rcv_nxt,
 			req->rsk_rcv_wnd >> inet_rsk(req)->rcv_wscale,
 			tcp_time_stamp_raw() + tcp_rsk(req)->ts_off,
-			req->ts_recent, sk->sk_bound_dev_if,
+			READ_ONCE(req->ts_recent), sk->sk_bound_dev_if,
 			tcp_v6_md5_do_lookup(sk, &ipv6_hdr(skb)->saddr, l3index),
 			ipv6_get_dsfield(ipv6_hdr(skb)), 0, sk->sk_priority);
 }
@@ -1325,7 +1330,6 @@
 	 */
 
 	newsk->sk_gso_type = SKB_GSO_TCPV6;
-	ip6_dst_store(newsk, dst, NULL, NULL);
 	inet6_sk_rx_dst_set(newsk, skb);
 
 	inet_sk(newsk)->pinet6 = tcp_inet6_sk(newsk);
@@ -1336,6 +1340,8 @@
 
 	memcpy(newnp, np, sizeof(struct ipv6_pinfo));
 
+	ip6_dst_store(newsk, dst, NULL, NULL);
+
 	newsk->sk_v6_daddr = ireq->ir_v6_rmt_addr;
 	newnp->saddr = ireq->ir_v6_loc_addr;
 	newsk->sk_v6_rcv_saddr = ireq->ir_v6_loc_addr;
@@ -1364,7 +1370,7 @@
 	/* Set ToS of the new socket based upon the value of incoming SYN.
 	 * ECT bits are set later in tcp_init_transfer().
 	 */
-	if (sock_net(sk)->ipv4.sysctl_tcp_reflect_tos)
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_reflect_tos))
 		newnp->tclass = tcp_rsk(req)->syn_tos & ~INET_ECN_MASK;
 
 	/* Clone native IPv6 options from listening socket (if any)
@@ -1424,14 +1430,11 @@
 
 		/* Clone pktoptions received with SYN, if we own the req */
 		if (ireq->pktopts) {
-			newnp->pktoptions = skb_clone(ireq->pktopts,
-						      sk_gfp_mask(sk, GFP_ATOMIC));
+			newnp->pktoptions = skb_clone_and_charge_r(ireq->pktopts, newsk);
 			consume_skb(ireq->pktopts);
 			ireq->pktopts = NULL;
-			if (newnp->pktoptions) {
+			if (newnp->pktoptions)
 				tcp_v6_restore_cb(newnp->pktoptions);
-				skb_set_owner_r(newnp->pktoptions, newsk);
-			}
 		}
 	} else {
 		if (!req_unhash && found_dup_sk) {
@@ -1500,20 +1503,23 @@
 	   by tcp. Feel free to propose better solution.
 					       --ANK (980728)
 	 */
-	if (np->rxopt.all)
-		opt_skb = skb_clone(skb, sk_gfp_mask(sk, GFP_ATOMIC));
+	if (np->rxopt.all && sk->sk_state != TCP_LISTEN)
+		opt_skb = skb_clone_and_charge_r(skb, sk);
 
 	if (sk->sk_state == TCP_ESTABLISHED) { /* Fast path */
-		struct dst_entry *dst = sk->sk_rx_dst;
+		struct dst_entry *dst;
+
+		dst = rcu_dereference_protected(sk->sk_rx_dst,
+						lockdep_sock_is_held(sk));
 
 		sock_rps_save_rxhash(sk, skb);
 		sk_mark_napi_id(sk, skb);
 		if (dst) {
-			if (inet_sk(sk)->rx_dst_ifindex != skb->skb_iif ||
+			if (sk->sk_rx_dst_ifindex != skb->skb_iif ||
 			    INDIRECT_CALL_1(dst->ops->check, ip6_dst_check,
-					    dst, np->rx_dst_cookie) == NULL) {
+					    dst, sk->sk_rx_dst_cookie) == NULL) {
+				RCU_INIT_POINTER(sk->sk_rx_dst, NULL);
 				dst_release(dst);
-				sk->sk_rx_dst = NULL;
 			}
 		}
 
@@ -1535,8 +1541,6 @@
 		if (nsk != sk) {
 			if (tcp_child_process(sk, nsk, skb))
 				goto reset;
-			if (opt_skb)
-				__kfree_skb(opt_skb);
 			return 0;
 		}
 	} else
@@ -1582,7 +1586,6 @@
 		if (np->repflow)
 			np->flow_label = ip6_flowlabel(ipv6_hdr(opt_skb));
 		if (ipv6_opt_accepted(sk, opt_skb, &TCP_SKB_CB(opt_skb)->header.h6)) {
-			skb_set_owner_r(opt_skb, sk);
 			tcp_v6_restore_cb(opt_skb);
 			opt_skb = xchg(&np->pktoptions, opt_skb);
 		} else {
@@ -1848,7 +1851,7 @@
 	goto discard_it;
 }
 
-INDIRECT_CALLABLE_SCOPE void tcp_v6_early_demux(struct sk_buff *skb)
+void tcp_v6_early_demux(struct sk_buff *skb)
 {
 	const struct ipv6hdr *hdr;
 	const struct tcphdr *th;
@@ -1875,12 +1878,12 @@
 		skb->sk = sk;
 		skb->destructor = sock_edemux;
 		if (sk_fullsock(sk)) {
-			struct dst_entry *dst = READ_ONCE(sk->sk_rx_dst);
+			struct dst_entry *dst = rcu_dereference(sk->sk_rx_dst);
 
 			if (dst)
-				dst = dst_check(dst, tcp_inet6_sk(sk)->rx_dst_cookie);
+				dst = dst_check(dst, sk->sk_rx_dst_cookie);
 			if (dst &&
-			    inet_sk(sk)->rx_dst_ifindex == skb->skb_iif)
+			    sk->sk_rx_dst_ifindex == skb->skb_iif)
 				skb_dst_set_noref(skb, dst);
 		}
 	}
@@ -1967,12 +1970,6 @@
 	return 0;
 }
 
-static void tcp_v6_destroy_sock(struct sock *sk)
-{
-	tcp_v4_destroy_sock(sk);
-	inet6_destroy_sock(sk);
-}
-
 #ifdef CONFIG_PROC_FS
 /* Proc filesystem TCPv6 sock list dumping. */
 static void get_openreq6(struct seq_file *seq,
@@ -2072,7 +2069,7 @@
 		   jiffies_to_clock_t(icsk->icsk_rto),
 		   jiffies_to_clock_t(icsk->icsk_ack.ato),
 		   (icsk->icsk_ack.quick << 1) | inet_csk_in_pingpong_mode(sp),
-		   tp->snd_cwnd,
+		   tcp_snd_cwnd(tp),
 		   state == TCP_LISTEN ?
 			fastopenq->max_qlen :
 			(tcp_in_initial_slowstart(tp) ? -1 : tp->snd_ssthresh)
@@ -2165,7 +2162,7 @@
 	.accept			= inet_csk_accept,
 	.ioctl			= tcp_ioctl,
 	.init			= tcp_v6_init_sock,
-	.destroy		= tcp_v6_destroy_sock,
+	.destroy		= tcp_v4_destroy_sock,
 	.shutdown		= tcp_shutdown,
 	.setsockopt		= tcp_setsockopt,
 	.getsockopt		= tcp_getsockopt,
@@ -2203,12 +2200,7 @@
 };
 EXPORT_SYMBOL_GPL(tcpv6_prot);
 
-/* thinking of making this const? Don't.
- * early_demux can change based on sysctl.
- */
-static struct inet6_protocol tcpv6_protocol = {
-	.early_demux	=	tcp_v6_early_demux,
-	.early_demux_handler =  tcp_v6_early_demux,
+static const struct inet6_protocol tcpv6_protocol = {
 	.handler	=	tcp_v6_rcv,
 	.err_handler	=	tcp_v6_err,
 	.flags		=	INET6_PROTO_NOPOLICY|INET6_PROTO_FINAL,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/udp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/udp.c
@@ -40,6 +40,7 @@
 #include <net/transp_v6.h>
 #include <net/ip6_route.h>
 #include <net/raw.h>
+#include <net/seg6.h>
 #include <net/tcp_states.h>
 #include <net/ip6_checksum.h>
 #include <net/ip6_tunnel.h>
@@ -54,11 +55,25 @@
 #include <trace/events/skb.h>
 #include "udp_impl.h"
 
-static u32 udp6_ehashfn(const struct net *net,
-			const struct in6_addr *laddr,
-			const u16 lport,
-			const struct in6_addr *faddr,
-			const __be16 fport)
+static void udpv6_destruct_sock(struct sock *sk)
+{
+	udp_destruct_common(sk);
+	inet6_sock_destruct(sk);
+}
+
+int udpv6_init_sock(struct sock *sk)
+{
+	skb_queue_head_init(&udp_sk(sk)->reader_queue);
+	sk->sk_destruct = udpv6_destruct_sock;
+	return 0;
+}
+
+INDIRECT_CALLABLE_SCOPE
+u32 udp6_ehashfn(const struct net *net,
+		 const struct in6_addr *laddr,
+		 const u16 lport,
+		 const struct in6_addr *faddr,
+		 const __be16 fport)
 {
 	static u32 udp6_ehash_secret __read_mostly;
 	static u32 udp_ipv6_hash_secret __read_mostly;
@@ -74,7 +89,7 @@
 	fhash = __ipv6_addr_jhash(faddr, udp_ipv6_hash_secret);
 
 	return __inet6_ehashfn(lhash, lport, fhash, fport,
-			       udp_ipv6_hash_secret + net_hash_mix(net));
+			       udp6_ehash_secret + net_hash_mix(net));
 }
 
 int udp_v6_get_port(struct sock *sk, unsigned short snum)
@@ -142,24 +157,6 @@
 	return score;
 }
 
-static struct sock *lookup_reuseport(struct net *net, struct sock *sk,
-				     struct sk_buff *skb,
-				     const struct in6_addr *saddr,
-				     __be16 sport,
-				     const struct in6_addr *daddr,
-				     unsigned int hnum)
-{
-	struct sock *reuse_sk = NULL;
-	u32 hash;
-
-	if (sk->sk_reuseport && sk->sk_state != TCP_ESTABLISHED) {
-		hash = udp6_ehashfn(net, daddr, hnum, saddr, sport);
-		reuse_sk = reuseport_select_sock(sk, hash, skb,
-						 sizeof(struct udphdr));
-	}
-	return reuse_sk;
-}
-
 /* called with rcu_read_lock() */
 static struct sock *udp6_lib_lookup2(struct net *net,
 		const struct in6_addr *saddr, __be16 sport,
@@ -169,21 +166,49 @@
 {
 	struct sock *sk, *result;
 	int score, badness;
+	bool need_rescore;
 
 	result = NULL;
 	badness = -1;
 	udp_portaddr_for_each_entry_rcu(sk, &hslot2->head) {
-		score = compute_score(sk, net, saddr, sport,
-				      daddr, hnum, dif, sdif);
+		need_rescore = false;
+rescore:
+		score = compute_score(need_rescore ? result : sk, net, saddr,
+				      sport, daddr, hnum, dif, sdif);
 		if (score > badness) {
-			result = lookup_reuseport(net, sk, skb,
-						  saddr, sport, daddr, hnum);
+			badness = score;
+
+			if (need_rescore)
+				continue;
+
+			if (sk->sk_state == TCP_ESTABLISHED) {
+				result = sk;
+				continue;
+			}
+
+			result = inet6_lookup_reuseport(net, sk, skb, sizeof(struct udphdr),
+							saddr, sport, daddr, hnum, udp6_ehashfn);
+			if (!result) {
+				result = sk;
+				continue;
+			}
+
 			/* Fall back to scoring if group has connections */
-			if (result && !reuseport_has_conns(sk, false))
+			if (!reuseport_has_conns(sk))
 				return result;
 
-			result = result ? : sk;
-			badness = score;
+			/* Reuseport logic returned an error, keep original score. */
+			if (IS_ERR(result))
+				continue;
+
+			/* compute_score is too long of a function to be
+			 * inlined, and calling it again here yields
+			 * measureable overhead for some
+			 * workloads. Work around it by jumping
+			 * backwards to rescore 'result'.
+			 */
+			need_rescore = true;
+			goto rescore;
 		}
 	}
 	return result;
@@ -208,7 +233,8 @@
 	if (no_reuseport || IS_ERR_OR_NULL(sk))
 		return sk;
 
-	reuse_sk = lookup_reuseport(net, sk, skb, saddr, sport, daddr, hnum);
+	reuse_sk = inet6_lookup_reuseport(net, sk, skb, sizeof(struct udphdr),
+					  saddr, sport, daddr, hnum, udp6_ehashfn);
 	if (reuse_sk)
 		sk = reuse_sk;
 	return sk;
@@ -450,7 +476,7 @@
 	goto try_again;
 }
 
-DEFINE_STATIC_KEY_FALSE(udpv6_encap_needed_key);
+DECLARE_STATIC_KEY_FALSE(udpv6_encap_needed_key);
 void udpv6_encap_enable(void)
 {
 	static_branch_inc(&udpv6_encap_needed_key);
@@ -561,7 +587,7 @@
 	struct ipv6_pinfo *np;
 	const struct ipv6hdr *hdr = (const struct ipv6hdr *)skb->data;
 	const struct in6_addr *saddr = &hdr->saddr;
-	const struct in6_addr *daddr = &hdr->daddr;
+	const struct in6_addr *daddr = seg6_get_daddr(skb, opt) ? : &hdr->daddr;
 	struct udphdr *uh = (struct udphdr *)(skb->data+offset);
 	bool tunnel = false;
 	struct sock *sk;
@@ -613,8 +639,11 @@
 	}
 
 	/* Tunnels don't have an application socket: don't pass errors back */
-	if (tunnel)
+	if (tunnel) {
+		if (udp_sk(sk)->encap_err_rcv)
+			udp_sk(sk)->encap_err_rcv(sk, skb, offset);
 		goto out;
+	}
 
 	if (!np->recverr) {
 		if (!harderr || sk->sk_state != TCP_ESTABLISHED)
@@ -884,7 +913,7 @@
 	if (udp_sk_rx_dst_set(sk, dst)) {
 		const struct rt6_info *rt = (const struct rt6_info *)dst;
 
-		inet6_sk(sk)->rx_dst_cookie = rt6_get_cookie(rt);
+		sk->sk_rx_dst_cookie = rt6_get_cookie(rt);
 	}
 }
 
@@ -910,6 +939,7 @@
 int __udp6_lib_rcv(struct sk_buff *skb, struct udp_table *udptable,
 		   int proto)
 {
+	enum skb_drop_reason reason = SKB_DROP_REASON_NOT_SPECIFIED;
 	const struct in6_addr *saddr, *daddr;
 	struct net *net = dev_net(skb->dev);
 	struct udphdr *uh;
@@ -956,7 +986,7 @@
 		struct dst_entry *dst = skb_dst(skb);
 		int ret;
 
-		if (unlikely(sk->sk_rx_dst != dst))
+		if (unlikely(rcu_dereference(sk->sk_rx_dst) != dst))
 			udp6_sk_rx_dst_set(sk, dst);
 
 		if (!uh->check && !udp_sk(sk)->no_check6_rx) {
@@ -986,6 +1016,8 @@
 		return udp6_unicast_rcv_skb(sk, skb, uh);
 	}
 
+	reason = SKB_DROP_REASON_NO_SOCKET;
+
 	if (!uh->check)
 		goto report_csum_error;
 
@@ -998,10 +1030,12 @@
 	__UDP6_INC_STATS(net, UDP_MIB_NOPORTS, proto == IPPROTO_UDPLITE);
 	icmpv6_send(skb, ICMPV6_DEST_UNREACH, ICMPV6_PORT_UNREACH, 0);
 
-	kfree_skb(skb);
+	kfree_skb_reason(skb, reason);
 	return 0;
 
 short_packet:
+	if (reason == SKB_DROP_REASON_NOT_SPECIFIED)
+		reason = SKB_DROP_REASON_PKT_TOO_SMALL;
 	net_dbg_ratelimited("UDP%sv6: short packet: From [%pI6c]:%u %d/%d to [%pI6c]:%u\n",
 			    proto == IPPROTO_UDPLITE ? "-Lite" : "",
 			    saddr, ntohs(uh->source),
@@ -1012,10 +1046,12 @@
 report_csum_error:
 	udp6_csum_zero_error(skb);
 csum_error:
+	if (reason == SKB_DROP_REASON_NOT_SPECIFIED)
+		reason = SKB_DROP_REASON_UDP_CSUM;
 	__UDP6_INC_STATS(net, UDP_MIB_CSUMERRORS, proto == IPPROTO_UDPLITE);
 discard:
 	__UDP6_INC_STATS(net, UDP_MIB_INERRORS, proto == IPPROTO_UDPLITE);
-	kfree_skb(skb);
+	kfree_skb_reason(skb, reason);
 	return 0;
 }
 
@@ -1034,7 +1070,7 @@
 
 	udp_portaddr_for_each_entry_rcu(sk, &hslot2->head) {
 		if (sk->sk_state == TCP_ESTABLISHED &&
-		    INET6_MATCH(sk, net, rmt_addr, loc_addr, ports, dif, sdif))
+		    inet6_match(net, sk, rmt_addr, loc_addr, ports, dif, sdif))
 			return sk;
 		/* Only check first socket in chain */
 		break;
@@ -1042,7 +1078,7 @@
 	return NULL;
 }
 
-INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)
+void udp_v6_early_demux(struct sk_buff *skb)
 {
 	struct net *net = dev_net(skb->dev);
 	const struct udphdr *uh;
@@ -1070,10 +1106,10 @@
 
 	skb->sk = sk;
 	skb->destructor = sock_efree;
-	dst = READ_ONCE(sk->sk_rx_dst);
+	dst = rcu_dereference(sk->sk_rx_dst);
 
 	if (dst)
-		dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie);
+		dst = dst_check(dst, sk->sk_rx_dst_cookie);
 	if (dst) {
 		/* set noref for now.
 		 * any place which wants to hold dst has to call
@@ -1200,11 +1236,11 @@
 		const int hlen = skb_network_header_len(skb) +
 				 sizeof(struct udphdr);
 
-		if (hlen + cork->gso_size > cork->fragsize) {
+		if (hlen + min(datalen, cork->gso_size) > cork->fragsize) {
 			kfree_skb(skb);
-			return -EINVAL;
+			return -EMSGSIZE;
 		}
-		if (skb->len > cork->gso_size * UDP_MAX_SEGMENTS) {
+		if (datalen > cork->gso_size * UDP_MAX_SEGMENTS) {
 			kfree_skb(skb);
 			return -EINVAL;
 		}
@@ -1355,9 +1391,11 @@
 			msg->msg_name = &sin;
 			msg->msg_namelen = sizeof(sin);
 do_udp_sendmsg:
-			if (__ipv6_only_sock(sk))
-				return -ENETUNREACH;
-			return udp_sendmsg(sk, msg, len);
+			err = __ipv6_only_sock(sk) ?
+				-ENETUNREACH : udp_sendmsg(sk, msg, len);
+			msg->msg_name = sin6;
+			msg->msg_namelen = addr_len;
+			return err;
 		}
 	}
 
@@ -1435,7 +1473,6 @@
 	if (!fl6.flowi6_oif)
 		fl6.flowi6_oif = np->sticky_pktinfo.ipi6_ifindex;
 
-	fl6.flowi6_mark = ipc6.sockc.mark;
 	fl6.flowi6_uid = sk->sk_uid;
 
 	if (msg->msg_controllen) {
@@ -1445,9 +1482,11 @@
 		ipc6.opt = opt;
 
 		err = udp_cmsg_send(sk, msg, &ipc6.gso_size);
-		if (err > 0)
+		if (err > 0) {
 			err = ip6_datagram_send_ctl(sock_net(sk), sk, msg, &fl6,
 						    &ipc6);
+			connected = false;
+		}
 		if (err < 0) {
 			fl6_sock_release(flowlabel);
 			return err;
@@ -1459,7 +1498,6 @@
 		}
 		if (!(opt->opt_nflen|opt->opt_flen))
 			opt = NULL;
-		connected = false;
 	}
 	if (!opt) {
 		opt = txopt_get(np);
@@ -1471,6 +1509,7 @@
 	ipc6.opt = opt;
 
 	fl6.flowi6_proto = sk->sk_protocol;
+	fl6.flowi6_mark = ipc6.sockc.mark;
 	fl6.daddr = *daddr;
 	if (ipv6_addr_any(&fl6.saddr) && !ipv6_addr_any(&np->saddr))
 		fl6.saddr = np->saddr;
@@ -1630,8 +1669,6 @@
 			udp_encap_disable();
 		}
 	}
-
-	inet6_destroy_sock(sk);
 }
 
 /*
@@ -1655,12 +1692,7 @@
 	return ipv6_getsockopt(sk, level, optname, optval, optlen);
 }
 
-/* thinking of making this const? Don't.
- * early_demux can change based on sysctl.
- */
-static struct inet6_protocol udpv6_protocol = {
-	.early_demux	=	udp_v6_early_demux,
-	.early_demux_handler =  udp_v6_early_demux,
+static const struct inet6_protocol udpv6_protocol = {
 	.handler	=	udpv6_rcv,
 	.err_handler	=	udpv6_err,
 	.flags		=	INET6_PROTO_NOPOLICY|INET6_PROTO_FINAL,
@@ -1720,7 +1752,7 @@
 	.connect		= ip6_datagram_connect,
 	.disconnect		= udp_disconnect,
 	.ioctl			= udp_ioctl,
-	.init			= udp_init_sock,
+	.init			= udpv6_init_sock,
 	.destroy		= udpv6_destroy_sock,
 	.setsockopt		= udpv6_setsockopt,
 	.getsockopt		= udpv6_getsockopt,
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/udp_impl.h
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/udp_impl.h
@@ -12,6 +12,7 @@
 int __udp6_lib_err(struct sk_buff *, struct inet6_skb_parm *, u8, u8, int,
 		   __be32, struct udp_table *);
 
+int udpv6_init_sock(struct sock *sk);
 int udp_v6_get_port(struct sock *sk, unsigned short snum);
 void udp_v6_rehash(struct sock *sk);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/udp_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/udp_offload.c
@@ -144,13 +144,11 @@
 
 skip:
 	NAPI_GRO_CB(skb)->is_ipv6 = 1;
-	rcu_read_lock();
 
 	if (static_branch_unlikely(&udpv6_encap_needed_key))
 		sk = udp6_gro_lookup_skb(skb, uh->source, uh->dest);
 
 	pp = udp_gro_receive(head, skb, uh, sk);
-	rcu_read_unlock();
 	return pp;
 
 flush:
@@ -170,13 +168,7 @@
 		skb_shinfo(skb)->gso_type |= (SKB_GSO_FRAGLIST|SKB_GSO_UDP_L4);
 		skb_shinfo(skb)->gso_segs = NAPI_GRO_CB(skb)->count;
 
-		if (skb->ip_summed == CHECKSUM_UNNECESSARY) {
-			if (skb->csum_level < SKB_MAX_CSUM_LEVEL)
-				skb->csum_level++;
-		} else {
-			skb->ip_summed = CHECKSUM_UNNECESSARY;
-			skb->csum_level = 0;
-		}
+		__skb_incr_checksum_unnecessary(skb);
 
 		return 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/udplite.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/udplite.c
@@ -12,6 +12,13 @@
 #include <linux/proc_fs.h>
 #include "udp_impl.h"
 
+static int udplitev6_sk_init(struct sock *sk)
+{
+	udpv6_init_sock(sk);
+	udp_sk(sk)->pcflag = UDPLITE_BIT;
+	return 0;
+}
+
 static int udplitev6_rcv(struct sk_buff *skb)
 {
 	return __udp6_lib_rcv(skb, &udplite_table, IPPROTO_UDPLITE);
@@ -38,7 +45,7 @@
 	.connect	   = ip6_datagram_connect,
 	.disconnect	   = udp_disconnect,
 	.ioctl		   = udp_ioctl,
-	.init		   = udplite_sk_init,
+	.init		   = udplitev6_sk_init,
 	.destroy	   = udpv6_destroy_sock,
 	.setsockopt	   = udpv6_setsockopt,
 	.getsockopt	   = udpv6_getsockopt,
@@ -50,6 +57,8 @@
 	.get_port	   = udp_v6_get_port,
 	.memory_allocated  = &udp_memory_allocated,
 	.sysctl_mem	   = sysctl_udp_mem,
+	.sysctl_wmem_offset = offsetof(struct net, ipv4.sysctl_udp_wmem_min),
+	.sysctl_rmem_offset = offsetof(struct net, ipv4.sysctl_udp_rmem_min),
 	.obj_size	   = sizeof(struct udp6_sock),
 	.h.udp_table	   = &udplite_table,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/xfrm6_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/xfrm6_input.c
@@ -56,7 +56,11 @@
 	skb_postpush_rcsum(skb, skb_network_header(skb), nhlen);
 
 	if (xo && (xo->flags & XFRM_GRO)) {
-		skb_mac_header_rebuild(skb);
+		/* The full l2 header needs to be preserved so that re-injecting the packet at l2
+		 * works correctly in the presence of vlan tags.
+		 */
+		skb_mac_header_rebuild_full(skb, xo->orig_mac_len);
+		skb_reset_network_header(skb);
 		skb_reset_transport_header(skb);
 		return 0;
 	}
@@ -86,6 +90,9 @@
 	__be32 *udpdata32;
 	__u16 encap_type = up->encap_type;
 
+	if (skb->protocol == htons(ETH_P_IP))
+		return xfrm4_udp_encap_rcv(sk, skb);
+
 	/* if this is not encapsulated socket, then just return now */
 	if (!encap_type)
 		return 1;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/xfrm6_output.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/xfrm6_output.c
@@ -45,6 +45,19 @@
 	return xfrm_output(sk, skb);
 }
 
+static int xfrm6_noneed_fragment(struct sk_buff *skb)
+{
+	struct frag_hdr *fh;
+	u8 prevhdr = ipv6_hdr(skb)->nexthdr;
+
+	if (prevhdr != NEXTHDR_FRAGMENT)
+		return 0;
+	fh = (struct frag_hdr *)(skb->data + sizeof(struct ipv6hdr));
+	if (fh->nexthdr == NEXTHDR_ESP || fh->nexthdr == NEXTHDR_AUTH)
+		return 1;
+	return 0;
+}
+
 static int __xfrm6_output(struct net *net, struct sock *sk, struct sk_buff *skb)
 {
 	struct dst_entry *dst = skb_dst(skb);
@@ -73,6 +86,9 @@
 		xfrm6_local_rxpmtu(skb, mtu);
 		kfree_skb(skb);
 		return -EMSGSIZE;
+	} else if (toobig && xfrm6_noneed_fragment(skb)) {
+		skb->ignore_df = 1;
+		goto skip_frag;
 	} else if (!skb->ignore_df && toobig && skb->sk) {
 		xfrm_local_error(skb, mtu);
 		kfree_skb(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ipv6/xfrm6_policy.c
+++ linux-xilinx-zynqmp-5.15.0/net/ipv6/xfrm6_policy.c
@@ -23,24 +23,24 @@
 #include <net/ip6_route.h>
 #include <net/l3mdev.h>
 
-static struct dst_entry *xfrm6_dst_lookup(struct net *net, int tos, int oif,
-					  const xfrm_address_t *saddr,
-					  const xfrm_address_t *daddr,
-					  u32 mark)
+static struct dst_entry *xfrm6_dst_lookup(const struct xfrm_dst_lookup_params *params)
 {
 	struct flowi6 fl6;
 	struct dst_entry *dst;
 	int err;
 
 	memset(&fl6, 0, sizeof(fl6));
-	fl6.flowi6_oif = l3mdev_master_ifindex_by_index(net, oif);
-	fl6.flowi6_flags = FLOWI_FLAG_SKIP_NH_OIF;
-	fl6.flowi6_mark = mark;
-	memcpy(&fl6.daddr, daddr, sizeof(fl6.daddr));
-	if (saddr)
-		memcpy(&fl6.saddr, saddr, sizeof(fl6.saddr));
+	fl6.flowi6_l3mdev = l3mdev_master_ifindex_by_index(params->net,
+							   params->oif);
+	fl6.flowi6_mark = params->mark;
+	memcpy(&fl6.daddr, params->daddr, sizeof(fl6.daddr));
+	if (params->saddr)
+		memcpy(&fl6.saddr, params->saddr, sizeof(fl6.saddr));
 
-	dst = ip6_route_output(net, NULL, &fl6);
+	fl6.flowi4_proto = params->ipproto;
+	fl6.uli = params->uli;
+
+	dst = ip6_route_output(params->net, NULL, &fl6);
 
 	err = dst->error;
 	if (dst->error) {
@@ -51,19 +51,25 @@
 	return dst;
 }
 
-static int xfrm6_get_saddr(struct net *net, int oif,
-			   xfrm_address_t *saddr, xfrm_address_t *daddr,
-			   u32 mark)
+static int xfrm6_get_saddr(xfrm_address_t *saddr,
+			   const struct xfrm_dst_lookup_params *params)
 {
 	struct dst_entry *dst;
 	struct net_device *dev;
+	struct inet6_dev *idev;
 
-	dst = xfrm6_dst_lookup(net, 0, oif, NULL, daddr, mark);
+	dst = xfrm6_dst_lookup(params);
 	if (IS_ERR(dst))
 		return -EHOSTUNREACH;
 
-	dev = ip6_dst_idev(dst)->dev;
-	ipv6_dev_get_saddr(dev_net(dev), dev, &daddr->in6, 0, &saddr->in6);
+	idev = ip6_dst_idev(dst);
+	if (!idev) {
+		dst_release(dst);
+		return -EHOSTUNREACH;
+	}
+	dev = idev->dev;
+	ipv6_dev_get_saddr(dev_net(dev), dev, &params->daddr->in6, 0,
+			   &saddr->in6);
 	dst_release(dst);
 	return 0;
 }
@@ -120,11 +126,11 @@
 {
 	struct xfrm_dst *xdst = (struct xfrm_dst *)dst;
 
-	if (likely(xdst->u.rt6.rt6i_idev))
-		in6_dev_put(xdst->u.rt6.rt6i_idev);
 	dst_destroy_metrics_generic(dst);
 	if (xdst->u.rt6.rt6i_uncached_list)
 		rt6_uncached_list_del(&xdst->u.rt6);
+	if (likely(xdst->u.rt6.rt6i_idev))
+		in6_dev_put(xdst->u.rt6.rt6i_idev);
 	xfrm_dst_destroy(xdst);
 }
 
@@ -289,9 +295,13 @@
 	if (ret)
 		goto out_state;
 
-	register_pernet_subsys(&xfrm6_net_ops);
+	ret = register_pernet_subsys(&xfrm6_net_ops);
+	if (ret)
+		goto out_protocol;
 out:
 	return ret;
+out_protocol:
+	xfrm6_protocol_fini();
 out_state:
 	xfrm6_state_fini();
 out_policy:
--- linux-xilinx-zynqmp-5.15.0.orig/net/iucv/af_iucv.c
+++ linux-xilinx-zynqmp-5.15.0/net/iucv/af_iucv.c
@@ -336,8 +336,8 @@
 	struct iucv_sock *iucv = iucv_sk(sk);
 	struct iucv_path *path = iucv->path;
 
-	if (iucv->path) {
-		iucv->path = NULL;
+	/* Whoever resets the path pointer, must sever and free it. */
+	if (xchg(&iucv->path, NULL)) {
 		if (with_user_data) {
 			low_nmcpy(user_data, iucv->src_name);
 			high_nmcpy(user_data, iucv->dst_name);
--- linux-xilinx-zynqmp-5.15.0.orig/net/iucv/iucv.c
+++ linux-xilinx-zynqmp-5.15.0/net/iucv/iucv.c
@@ -83,7 +83,7 @@
 	u16 ippathid;
 	u8  ipflags1;
 	u8  iptype;
-	u32 res2[8];
+	u32 res2[9];
 };
 
 struct iucv_irq_list {
@@ -156,7 +156,7 @@
 static LIST_HEAD(iucv_handler_list);
 
 /*
- * iucv_path_table: an array of iucv_path structures.
+ * iucv_path_table: array of pointers to iucv_path structures.
  */
 static struct iucv_path **iucv_path_table;
 static unsigned long iucv_max_pathid;
@@ -519,7 +519,7 @@
  */
 static void iucv_setmask_up(void)
 {
-	cpumask_t cpumask;
+	static cpumask_t cpumask;
 	int cpu;
 
 	/* Disable all cpu but the first in cpu_irq_cpumask. */
@@ -544,7 +544,7 @@
 
 	cpus_read_lock();
 	rc = -ENOMEM;
-	alloc_size = iucv_max_pathid * sizeof(struct iucv_path);
+	alloc_size = iucv_max_pathid * sizeof(*iucv_path_table);
 	iucv_path_table = kzalloc(alloc_size, GFP_KERNEL);
 	if (!iucv_path_table)
 		goto out;
@@ -627,23 +627,33 @@
 
 static int iucv_cpu_down_prep(unsigned int cpu)
 {
-	cpumask_t cpumask;
+	cpumask_var_t cpumask;
+	int ret = 0;
 
 	if (!iucv_path_table)
 		return 0;
 
-	cpumask_copy(&cpumask, &iucv_buffer_cpumask);
-	cpumask_clear_cpu(cpu, &cpumask);
-	if (cpumask_empty(&cpumask))
+	if (!alloc_cpumask_var(&cpumask, GFP_KERNEL))
+		return -ENOMEM;
+
+	cpumask_copy(cpumask, &iucv_buffer_cpumask);
+	cpumask_clear_cpu(cpu, cpumask);
+	if (cpumask_empty(cpumask)) {
 		/* Can't offline last IUCV enabled cpu. */
-		return -EINVAL;
+		ret = -EINVAL;
+		goto __free_cpumask;
+	}
 
 	iucv_retrieve_cpu(NULL);
 	if (!cpumask_empty(&iucv_irq_cpumask))
-		return 0;
+		goto __free_cpumask;
+
 	smp_call_function_single(cpumask_first(&iucv_buffer_cpumask),
 				 iucv_allow_cpu, NULL, 1);
-	return 0;
+
+__free_cpumask:
+	free_cpumask_var(cpumask);
+	return ret;
 }
 
 /**
@@ -1080,8 +1090,7 @@
 		size = (size < 8) ? size : 8;
 		for (array = buffer; size > 0; array++) {
 			copy = min_t(size_t, size, array->length);
-			memcpy((u8 *)(addr_t) array->address,
-				rmmsg, copy);
+			memcpy(phys_to_virt(array->address), rmmsg, copy);
 			rmmsg += copy;
 			size -= copy;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/net/kcm/kcmsock.c
+++ linux-xilinx-zynqmp-5.15.0/net/kcm/kcmsock.c
@@ -161,7 +161,8 @@
 	/* Buffer limit is okay now, add to ready list */
 	list_add_tail(&kcm->wait_rx_list,
 		      &kcm->mux->kcm_rx_waiters);
-	kcm->rx_wait = true;
+	/* paired with lockless reads in kcm_rfree() */
+	WRITE_ONCE(kcm->rx_wait, true);
 }
 
 static void kcm_rfree(struct sk_buff *skb)
@@ -177,7 +178,7 @@
 	/* For reading rx_wait and rx_psock without holding lock */
 	smp_mb__after_atomic();
 
-	if (!kcm->rx_wait && !kcm->rx_psock &&
+	if (!READ_ONCE(kcm->rx_wait) && !READ_ONCE(kcm->rx_psock) &&
 	    sk_rmem_alloc_get(sk) < sk->sk_rcvlowat) {
 		spin_lock_bh(&mux->rx_lock);
 		kcm_rcv_ready(kcm);
@@ -220,7 +221,7 @@
 	struct sk_buff *skb;
 	struct kcm_sock *kcm;
 
-	while ((skb = __skb_dequeue(head))) {
+	while ((skb = skb_dequeue(head))) {
 		/* Reset destructor to avoid calling kcm_rcv_ready */
 		skb->destructor = sock_rfree;
 		skb_orphan(skb);
@@ -236,7 +237,8 @@
 		if (kcm_queue_rcv_skb(&kcm->sk, skb)) {
 			/* Should mean socket buffer full */
 			list_del(&kcm->wait_rx_list);
-			kcm->rx_wait = false;
+			/* paired with lockless reads in kcm_rfree() */
+			WRITE_ONCE(kcm->rx_wait, false);
 
 			/* Commit rx_wait to read in kcm_free */
 			smp_wmb();
@@ -279,10 +281,12 @@
 	kcm = list_first_entry(&mux->kcm_rx_waiters,
 			       struct kcm_sock, wait_rx_list);
 	list_del(&kcm->wait_rx_list);
-	kcm->rx_wait = false;
+	/* paired with lockless reads in kcm_rfree() */
+	WRITE_ONCE(kcm->rx_wait, false);
 
 	psock->rx_kcm = kcm;
-	kcm->rx_psock = psock;
+	/* paired with lockless reads in kcm_rfree() */
+	WRITE_ONCE(kcm->rx_psock, psock);
 
 	spin_unlock_bh(&mux->rx_lock);
 
@@ -309,7 +313,8 @@
 	spin_lock_bh(&mux->rx_lock);
 
 	psock->rx_kcm = NULL;
-	kcm->rx_psock = NULL;
+	/* paired with lockless reads in kcm_rfree() */
+	WRITE_ONCE(kcm->rx_psock, NULL);
 
 	/* Commit kcm->rx_psock before sk_rmem_alloc_get to sync with
 	 * kcm_rfree
@@ -833,7 +838,7 @@
 	}
 
 	get_page(page);
-	skb_fill_page_desc(skb, i, page, offset, size);
+	skb_fill_page_desc_noacc(skb, i, page, offset, size);
 	skb_shinfo(skb)->flags |= SKBFL_SHARED_FRAG;
 
 coalesced:
@@ -906,6 +911,7 @@
 		  !(msg->msg_flags & MSG_MORE) : !!(msg->msg_flags & MSG_EOR);
 	int err = -EPIPE;
 
+	mutex_lock(&kcm->tx_mutex);
 	lock_sock(sk);
 
 	/* Per tcp_sendmsg this should be in poll */
@@ -1054,20 +1060,24 @@
 	KCM_STATS_ADD(kcm->stats.tx_bytes, copied);
 
 	release_sock(sk);
+	mutex_unlock(&kcm->tx_mutex);
 	return copied;
 
 out_error:
 	kcm_push(kcm);
 
-	if (copied && sock->type == SOCK_SEQPACKET) {
+	if (sock->type == SOCK_SEQPACKET) {
 		/* Wrote some bytes before encountering an
 		 * error, return partial success.
 		 */
-		goto partial_message;
-	}
-
-	if (head != kcm->seq_skb)
+		if (copied)
+			goto partial_message;
+		if (head != kcm->seq_skb)
+			kfree_skb(head);
+	} else {
 		kfree_skb(head);
+		kcm->seq_skb = NULL;
+	}
 
 	err = sk_stream_error(sk, msg->msg_flags, err);
 
@@ -1076,56 +1086,22 @@
 		sk->sk_write_space(sk);
 
 	release_sock(sk);
+	mutex_unlock(&kcm->tx_mutex);
 	return err;
 }
 
-static struct sk_buff *kcm_wait_data(struct sock *sk, int flags,
-				     long timeo, int *err)
-{
-	struct sk_buff *skb;
-
-	while (!(skb = skb_peek(&sk->sk_receive_queue))) {
-		if (sk->sk_err) {
-			*err = sock_error(sk);
-			return NULL;
-		}
-
-		if (sock_flag(sk, SOCK_DONE))
-			return NULL;
-
-		if ((flags & MSG_DONTWAIT) || !timeo) {
-			*err = -EAGAIN;
-			return NULL;
-		}
-
-		sk_wait_data(sk, &timeo, NULL);
-
-		/* Handle signals */
-		if (signal_pending(current)) {
-			*err = sock_intr_errno(timeo);
-			return NULL;
-		}
-	}
-
-	return skb;
-}
-
 static int kcm_recvmsg(struct socket *sock, struct msghdr *msg,
 		       size_t len, int flags)
 {
+	int noblock = flags & MSG_DONTWAIT;
 	struct sock *sk = sock->sk;
 	struct kcm_sock *kcm = kcm_sk(sk);
 	int err = 0;
-	long timeo;
 	struct strp_msg *stm;
 	int copied = 0;
 	struct sk_buff *skb;
 
-	timeo = sock_rcvtimeo(sk, flags & MSG_DONTWAIT);
-
-	lock_sock(sk);
-
-	skb = kcm_wait_data(sk, flags, timeo, &err);
+	skb = skb_recv_datagram(sk, flags, noblock, &err);
 	if (!skb)
 		goto out;
 
@@ -1156,14 +1132,11 @@
 			/* Finished with message */
 			msg->msg_flags |= MSG_EOR;
 			KCM_STATS_INCR(kcm->stats.rx_msgs);
-			skb_unlink(skb, &sk->sk_receive_queue);
-			kfree_skb(skb);
 		}
 	}
 
 out:
-	release_sock(sk);
-
+	skb_free_datagram(sk, skb);
 	return copied ? : err;
 }
 
@@ -1171,9 +1144,9 @@
 			       struct pipe_inode_info *pipe, size_t len,
 			       unsigned int flags)
 {
+	int noblock = flags & MSG_DONTWAIT;
 	struct sock *sk = sock->sk;
 	struct kcm_sock *kcm = kcm_sk(sk);
-	long timeo;
 	struct strp_msg *stm;
 	int err = 0;
 	ssize_t copied;
@@ -1181,11 +1154,7 @@
 
 	/* Only support splice for SOCKSEQPACKET */
 
-	timeo = sock_rcvtimeo(sk, flags & MSG_DONTWAIT);
-
-	lock_sock(sk);
-
-	skb = kcm_wait_data(sk, flags, timeo, &err);
+	skb = skb_recv_datagram(sk, flags, noblock, &err);
 	if (!skb)
 		goto err_out;
 
@@ -1213,13 +1182,11 @@
 	 * finish reading the message.
 	 */
 
-	release_sock(sk);
-
+	skb_free_datagram(sk, skb);
 	return copied;
 
 err_out:
-	release_sock(sk);
-
+	skb_free_datagram(sk, skb);
 	return err;
 }
 
@@ -1239,7 +1206,8 @@
 	if (!kcm->rx_psock) {
 		if (kcm->rx_wait) {
 			list_del(&kcm->wait_rx_list);
-			kcm->rx_wait = false;
+			/* paired with lockless reads in kcm_rfree() */
+			WRITE_ONCE(kcm->rx_wait, false);
 		}
 
 		requeue_rx_msgs(mux, &kcm->sk.sk_receive_queue);
@@ -1310,10 +1278,11 @@
 	if (get_user(len, optlen))
 		return -EFAULT;
 
-	len = min_t(unsigned int, len, sizeof(int));
 	if (len < 0)
 		return -EINVAL;
 
+	len = min_t(unsigned int, len, sizeof(int));
+
 	switch (optname) {
 	case KCM_RECV_DISABLE:
 		val = kcm->rx_disabled;
@@ -1360,6 +1329,7 @@
 	spin_unlock_bh(&mux->lock);
 
 	INIT_WORK(&kcm->tx_work, kcm_tx_work);
+	mutex_init(&kcm->tx_mutex);
 
 	spin_lock_bh(&mux->rx_lock);
 	kcm_rcv_ready(kcm);
@@ -1411,12 +1381,6 @@
 	psock->sk = csk;
 	psock->bpf_prog = prog;
 
-	err = strp_init(&psock->strp, csk, &cb);
-	if (err) {
-		kmem_cache_free(kcm_psockp, psock);
-		goto out;
-	}
-
 	write_lock_bh(&csk->sk_callback_lock);
 
 	/* Check if sk_user_data is already by KCM or someone else.
@@ -1424,13 +1388,18 @@
 	 */
 	if (csk->sk_user_data) {
 		write_unlock_bh(&csk->sk_callback_lock);
-		strp_stop(&psock->strp);
-		strp_done(&psock->strp);
 		kmem_cache_free(kcm_psockp, psock);
 		err = -EALREADY;
 		goto out;
 	}
 
+	err = strp_init(&psock->strp, csk, &cb);
+	if (err) {
+		write_unlock_bh(&csk->sk_callback_lock);
+		kmem_cache_free(kcm_psockp, psock);
+		goto out;
+	}
+
 	psock->save_data_ready = csk->sk_data_ready;
 	psock->save_write_space = csk->sk_write_space;
 	psock->save_state_change = csk->sk_state_change;
@@ -1793,7 +1762,8 @@
 
 	if (kcm->rx_wait) {
 		list_del(&kcm->wait_rx_list);
-		kcm->rx_wait = false;
+		/* paired with lockless reads in kcm_rfree() */
+		WRITE_ONCE(kcm->rx_wait, false);
 	}
 	/* Move any pending receive messages to other kcm sockets */
 	requeue_rx_msgs(mux, &sk->sk_receive_queue);
@@ -1838,10 +1808,10 @@
 	kcm = kcm_sk(sk);
 	mux = kcm->mux;
 
+	lock_sock(sk);
 	sock_orphan(sk);
 	kfree_skb(kcm->seq_skb);
 
-	lock_sock(sk);
 	/* Purge queue under lock to avoid race condition with tx_work trying
 	 * to act when queue is nonempty. If tx_work runs after this point
 	 * it will just return.
@@ -2020,6 +1990,8 @@
 	 * that all multiplexors and psocks have been destroyed.
 	 */
 	WARN_ON(!list_empty(&knet->mux_list));
+
+	mutex_destroy(&knet->mutex);
 }
 
 static struct pernet_operations kcm_net_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/key/af_key.c
+++ linux-xilinx-zynqmp-5.15.0/net/key/af_key.c
@@ -1697,9 +1697,12 @@
 		pfk->registered |= (1<<hdr->sadb_msg_satype);
 	}
 
+	mutex_lock(&pfkey_mutex);
 	xfrm_probe_algs();
 
-	supp_skb = compose_sadb_supported(hdr, GFP_KERNEL);
+	supp_skb = compose_sadb_supported(hdr, GFP_KERNEL | __GFP_ZERO);
+	mutex_unlock(&pfkey_mutex);
+
 	if (!supp_skb) {
 		if (hdr->sadb_msg_satype != SADB_SATYPE_UNSPEC)
 			pfk->registered &= ~(1<<hdr->sadb_msg_satype);
@@ -1845,9 +1848,9 @@
 	if (ext_hdrs[SADB_X_EXT_FILTER - 1]) {
 		struct sadb_x_filter *xfilter = ext_hdrs[SADB_X_EXT_FILTER - 1];
 
-		if ((xfilter->sadb_x_filter_splen >=
+		if ((xfilter->sadb_x_filter_splen >
 			(sizeof(xfrm_address_t) << 3)) ||
-		    (xfilter->sadb_x_filter_dplen >=
+		    (xfilter->sadb_x_filter_dplen >
 			(sizeof(xfrm_address_t) << 3))) {
 			mutex_unlock(&pfk->dump_lock);
 			return -EINVAL;
@@ -1937,7 +1940,8 @@
 }
 
 static int
-parse_ipsecrequest(struct xfrm_policy *xp, struct sadb_x_ipsecrequest *rq)
+parse_ipsecrequest(struct xfrm_policy *xp, struct sadb_x_policy *pol,
+		   struct sadb_x_ipsecrequest *rq)
 {
 	struct net *net = xp_net(xp);
 	struct xfrm_tmpl *t = xp->xfrm_vec + xp->xfrm_nr;
@@ -1955,9 +1959,12 @@
 	if ((mode = pfkey_mode_to_xfrm(rq->sadb_x_ipsecrequest_mode)) < 0)
 		return -EINVAL;
 	t->mode = mode;
-	if (rq->sadb_x_ipsecrequest_level == IPSEC_LEVEL_USE)
+	if (rq->sadb_x_ipsecrequest_level == IPSEC_LEVEL_USE) {
+		if ((mode == XFRM_MODE_TUNNEL || mode == XFRM_MODE_BEET) &&
+		    pol->sadb_x_policy_dir == IPSEC_DIR_OUTBOUND)
+			return -EINVAL;
 		t->optional = 1;
-	else if (rq->sadb_x_ipsecrequest_level == IPSEC_LEVEL_UNIQUE) {
+	} else if (rq->sadb_x_ipsecrequest_level == IPSEC_LEVEL_UNIQUE) {
 		t->reqid = rq->sadb_x_ipsecrequest_reqid;
 		if (t->reqid > IPSEC_MANUAL_REQID_MAX)
 			t->reqid = 0;
@@ -1999,7 +2006,7 @@
 		    rq->sadb_x_ipsecrequest_len < sizeof(*rq))
 			return -EINVAL;
 
-		if ((err = parse_ipsecrequest(xp, rq)) < 0)
+		if ((err = parse_ipsecrequest(xp, pol, rq)) < 0)
 			return err;
 		len -= rq->sadb_x_ipsecrequest_len;
 		rq = (void*)((u8*)rq + rq->sadb_x_ipsecrequest_len);
@@ -2623,7 +2630,7 @@
 	}
 
 	return xfrm_migrate(&sel, dir, XFRM_POLICY_TYPE_MAIN, m, i,
-			    kma ? &k : NULL, net, NULL);
+			    kma ? &k : NULL, net, NULL, 0);
 
  out:
 	return err;
@@ -2934,9 +2941,10 @@
 	return sz + sizeof(struct sadb_prop);
 }
 
-static void dump_ah_combs(struct sk_buff *skb, const struct xfrm_tmpl *t)
+static int dump_ah_combs(struct sk_buff *skb, const struct xfrm_tmpl *t)
 {
 	struct sadb_prop *p;
+	int sz = 0;
 	int i;
 
 	p = skb_put(skb, sizeof(struct sadb_prop));
@@ -2964,13 +2972,17 @@
 			c->sadb_comb_soft_addtime = 20*60*60;
 			c->sadb_comb_hard_usetime = 8*60*60;
 			c->sadb_comb_soft_usetime = 7*60*60;
+			sz += sizeof(*c);
 		}
 	}
+
+	return sz + sizeof(*p);
 }
 
-static void dump_esp_combs(struct sk_buff *skb, const struct xfrm_tmpl *t)
+static int dump_esp_combs(struct sk_buff *skb, const struct xfrm_tmpl *t)
 {
 	struct sadb_prop *p;
+	int sz = 0;
 	int i, k;
 
 	p = skb_put(skb, sizeof(struct sadb_prop));
@@ -3012,8 +3024,11 @@
 			c->sadb_comb_soft_addtime = 20*60*60;
 			c->sadb_comb_hard_usetime = 8*60*60;
 			c->sadb_comb_soft_usetime = 7*60*60;
+			sz += sizeof(*c);
 		}
 	}
+
+	return sz + sizeof(*p);
 }
 
 static int key_notify_policy_expire(struct xfrm_policy *xp, const struct km_event *c)
@@ -3143,6 +3158,7 @@
 	struct sadb_x_sec_ctx *sec_ctx;
 	struct xfrm_sec_ctx *xfrm_ctx;
 	int ctx_size = 0;
+	int alg_size = 0;
 
 	sockaddr_size = pfkey_sockaddr_size(x->props.family);
 	if (!sockaddr_size)
@@ -3154,16 +3170,16 @@
 		sizeof(struct sadb_x_policy);
 
 	if (x->id.proto == IPPROTO_AH)
-		size += count_ah_combs(t);
+		alg_size = count_ah_combs(t);
 	else if (x->id.proto == IPPROTO_ESP)
-		size += count_esp_combs(t);
+		alg_size = count_esp_combs(t);
 
 	if ((xfrm_ctx = x->security)) {
 		ctx_size = PFKEY_ALIGN8(xfrm_ctx->ctx_len);
 		size +=  sizeof(struct sadb_x_sec_ctx) + ctx_size;
 	}
 
-	skb =  alloc_skb(size + 16, GFP_ATOMIC);
+	skb =  alloc_skb(size + alg_size + 16, GFP_ATOMIC);
 	if (skb == NULL)
 		return -ENOMEM;
 
@@ -3217,10 +3233,13 @@
 	pol->sadb_x_policy_priority = xp->priority;
 
 	/* Set sadb_comb's. */
+	alg_size = 0;
 	if (x->id.proto == IPPROTO_AH)
-		dump_ah_combs(skb, t);
+		alg_size = dump_ah_combs(skb, t);
 	else if (x->id.proto == IPPROTO_ESP)
-		dump_esp_combs(skb, t);
+		alg_size = dump_esp_combs(skb, t);
+
+	hdr->sadb_msg_len += alg_size / 8;
 
 	/* security context */
 	if (xfrm_ctx) {
@@ -3375,7 +3394,7 @@
 	hdr->sadb_msg_len = size / sizeof(uint64_t);
 	hdr->sadb_msg_errno = 0;
 	hdr->sadb_msg_reserved = 0;
-	hdr->sadb_msg_seq = x->km.seq = get_acqseq();
+	hdr->sadb_msg_seq = x->km.seq;
 	hdr->sadb_msg_pid = 0;
 
 	/* SA */
--- linux-xilinx-zynqmp-5.15.0.orig/net/l2tp/l2tp_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/l2tp/l2tp_core.c
@@ -88,6 +88,11 @@
 /* Default trace flags */
 #define L2TP_DEFAULT_DEBUG_FLAGS	0
 
+#define L2TP_DEPTH_NESTING		2
+#if L2TP_DEPTH_NESTING == SINGLE_DEPTH_NESTING
+#error "L2TP requires its own lockdep subclass"
+#endif
+
 /* Private data stored for received packets in the skb.
  */
 struct l2tp_skb_cb {
@@ -104,9 +109,9 @@
 /* per-net private data for this module */
 static unsigned int l2tp_net_id;
 struct l2tp_net {
-	struct list_head l2tp_tunnel_list;
-	/* Lock for write access to l2tp_tunnel_list */
-	spinlock_t l2tp_tunnel_list_lock;
+	/* Lock for write access to l2tp_tunnel_idr */
+	spinlock_t l2tp_tunnel_idr_lock;
+	struct idr l2tp_tunnel_idr;
 	struct hlist_head l2tp_session_hlist[L2TP_HASH_SIZE_2];
 	/* Lock for write access to l2tp_session_hlist */
 	spinlock_t l2tp_session_hlist_lock;
@@ -208,13 +213,10 @@
 	struct l2tp_tunnel *tunnel;
 
 	rcu_read_lock_bh();
-	list_for_each_entry_rcu(tunnel, &pn->l2tp_tunnel_list, list) {
-		if (tunnel->tunnel_id == tunnel_id &&
-		    refcount_inc_not_zero(&tunnel->ref_count)) {
-			rcu_read_unlock_bh();
-
-			return tunnel;
-		}
+	tunnel = idr_find(&pn->l2tp_tunnel_idr, tunnel_id);
+	if (tunnel && refcount_inc_not_zero(&tunnel->ref_count)) {
+		rcu_read_unlock_bh();
+		return tunnel;
 	}
 	rcu_read_unlock_bh();
 
@@ -224,13 +226,14 @@
 
 struct l2tp_tunnel *l2tp_tunnel_get_nth(const struct net *net, int nth)
 {
-	const struct l2tp_net *pn = l2tp_pernet(net);
+	struct l2tp_net *pn = l2tp_pernet(net);
+	unsigned long tunnel_id, tmp;
 	struct l2tp_tunnel *tunnel;
 	int count = 0;
 
 	rcu_read_lock_bh();
-	list_for_each_entry_rcu(tunnel, &pn->l2tp_tunnel_list, list) {
-		if (++count > nth &&
+	idr_for_each_entry_ul(&pn->l2tp_tunnel_idr, tunnel, tmp, tunnel_id) {
+		if (tunnel && ++count > nth &&
 		    refcount_inc_not_zero(&tunnel->ref_count)) {
 			rcu_read_unlock_bh();
 			return tunnel;
@@ -1043,7 +1046,13 @@
 	IPCB(skb)->flags &= ~(IPSKB_XFRM_TUNNEL_SIZE | IPSKB_XFRM_TRANSFORMED | IPSKB_REROUTED);
 	nf_reset_ct(skb);
 
-	bh_lock_sock(sk);
+	/* L2TP uses its own lockdep subclass to avoid lockdep splats caused by
+	 * nested socket calls on the same lockdep socket class. This can
+	 * happen when data from a user socket is routed over l2tp, which uses
+	 * another userspace socket.
+	 */
+	spin_lock_nested(&sk->sk_lock.slock, L2TP_DEPTH_NESTING);
+
 	if (sock_owned_by_user(sk)) {
 		kfree_skb(skb);
 		ret = NET_XMIT_DROP;
@@ -1095,7 +1104,7 @@
 	ret = l2tp_xmit_queue(tunnel, skb, &inet->cork.fl);
 
 out_unlock:
-	bh_unlock_sock(sk);
+	spin_unlock(&sk->sk_lock.slock);
 
 	return ret;
 }
@@ -1150,8 +1159,10 @@
 	}
 
 	/* Remove hooks into tunnel socket */
+	write_lock_bh(&sk->sk_callback_lock);
 	sk->sk_destruct = tunnel->old_sk_destruct;
 	sk->sk_user_data = NULL;
+	write_unlock_bh(&sk->sk_callback_lock);
 
 	/* Call the original destructor */
 	if (sk->sk_destruct)
@@ -1227,6 +1238,15 @@
 		l2tp_tunnel_delete(tunnel);
 }
 
+static void l2tp_tunnel_remove(struct net *net, struct l2tp_tunnel *tunnel)
+{
+	struct l2tp_net *pn = l2tp_pernet(net);
+
+	spin_lock_bh(&pn->l2tp_tunnel_idr_lock);
+	idr_remove(&pn->l2tp_tunnel_idr, tunnel->tunnel_id);
+	spin_unlock_bh(&pn->l2tp_tunnel_idr_lock);
+}
+
 /* Workqueue tunnel deletion function */
 static void l2tp_tunnel_del_work(struct work_struct *work)
 {
@@ -1234,7 +1254,6 @@
 						  del_work);
 	struct sock *sk = tunnel->sock;
 	struct socket *sock = sk->sk_socket;
-	struct l2tp_net *pn;
 
 	l2tp_tunnel_closeall(tunnel);
 
@@ -1248,12 +1267,7 @@
 		}
 	}
 
-	/* Remove the tunnel struct from the tunnel list */
-	pn = l2tp_pernet(tunnel->l2tp_net);
-	spin_lock_bh(&pn->l2tp_tunnel_list_lock);
-	list_del_rcu(&tunnel->list);
-	spin_unlock_bh(&pn->l2tp_tunnel_list_lock);
-
+	l2tp_tunnel_remove(tunnel->l2tp_net, tunnel);
 	/* drop initial ref */
 	l2tp_tunnel_dec_refcount(tunnel);
 
@@ -1384,8 +1398,6 @@
 	return err;
 }
 
-static struct lock_class_key l2tp_socket_class;
-
 int l2tp_tunnel_create(int fd, int version, u32 tunnel_id, u32 peer_tunnel_id,
 		       struct l2tp_tunnel_cfg *cfg, struct l2tp_tunnel **tunnelp)
 {
@@ -1455,12 +1467,19 @@
 int l2tp_tunnel_register(struct l2tp_tunnel *tunnel, struct net *net,
 			 struct l2tp_tunnel_cfg *cfg)
 {
-	struct l2tp_tunnel *tunnel_walk;
-	struct l2tp_net *pn;
+	struct l2tp_net *pn = l2tp_pernet(net);
+	u32 tunnel_id = tunnel->tunnel_id;
 	struct socket *sock;
 	struct sock *sk;
 	int ret;
 
+	spin_lock_bh(&pn->l2tp_tunnel_idr_lock);
+	ret = idr_alloc_u32(&pn->l2tp_tunnel_idr, NULL, &tunnel_id, tunnel_id,
+			    GFP_ATOMIC);
+	spin_unlock_bh(&pn->l2tp_tunnel_idr_lock);
+	if (ret)
+		return ret == -ENOSPC ? -EEXIST : ret;
+
 	if (tunnel->fd < 0) {
 		ret = l2tp_tunnel_sock_create(net, tunnel->tunnel_id,
 					      tunnel->peer_tunnel_id, cfg,
@@ -1471,30 +1490,16 @@
 		sock = sockfd_lookup(tunnel->fd, &ret);
 		if (!sock)
 			goto err;
-
-		ret = l2tp_validate_socket(sock->sk, net, tunnel->encap);
-		if (ret < 0)
-			goto err_sock;
 	}
 
-	tunnel->l2tp_net = net;
-	pn = l2tp_pernet(net);
-
 	sk = sock->sk;
-	sock_hold(sk);
-	tunnel->sock = sk;
-
-	spin_lock_bh(&pn->l2tp_tunnel_list_lock);
-	list_for_each_entry(tunnel_walk, &pn->l2tp_tunnel_list, list) {
-		if (tunnel_walk->tunnel_id == tunnel->tunnel_id) {
-			spin_unlock_bh(&pn->l2tp_tunnel_list_lock);
-			sock_put(sk);
-			ret = -EEXIST;
-			goto err_sock;
-		}
-	}
-	list_add_rcu(&tunnel->list, &pn->l2tp_tunnel_list);
-	spin_unlock_bh(&pn->l2tp_tunnel_list_lock);
+	lock_sock(sk);
+	write_lock_bh(&sk->sk_callback_lock);
+	ret = l2tp_validate_socket(sk, net, tunnel->encap);
+	if (ret < 0)
+		goto err_inval_sock;
+	rcu_assign_sk_user_data(sk, tunnel);
+	write_unlock_bh(&sk->sk_callback_lock);
 
 	if (tunnel->encap == L2TP_ENCAPTYPE_UDP) {
 		struct udp_tunnel_sock_cfg udp_cfg = {
@@ -1505,15 +1510,20 @@
 		};
 
 		setup_udp_tunnel_sock(net, sock, &udp_cfg);
-	} else {
-		sk->sk_user_data = tunnel;
 	}
 
 	tunnel->old_sk_destruct = sk->sk_destruct;
 	sk->sk_destruct = &l2tp_tunnel_destruct;
-	lockdep_set_class_and_name(&sk->sk_lock.slock, &l2tp_socket_class,
-				   "l2tp_sock");
 	sk->sk_allocation = GFP_ATOMIC;
+	release_sock(sk);
+
+	sock_hold(sk);
+	tunnel->sock = sk;
+	tunnel->l2tp_net = net;
+
+	spin_lock_bh(&pn->l2tp_tunnel_idr_lock);
+	idr_replace(&pn->l2tp_tunnel_idr, tunnel, tunnel->tunnel_id);
+	spin_unlock_bh(&pn->l2tp_tunnel_idr_lock);
 
 	trace_register_tunnel(tunnel);
 
@@ -1522,12 +1532,16 @@
 
 	return 0;
 
-err_sock:
+err_inval_sock:
+	write_unlock_bh(&sk->sk_callback_lock);
+	release_sock(sk);
+
 	if (tunnel->fd < 0)
 		sock_release(sock);
 	else
 		sockfd_put(sock);
 err:
+	l2tp_tunnel_remove(net, tunnel);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(l2tp_tunnel_register);
@@ -1641,8 +1655,8 @@
 	struct l2tp_net *pn = net_generic(net, l2tp_net_id);
 	int hash;
 
-	INIT_LIST_HEAD(&pn->l2tp_tunnel_list);
-	spin_lock_init(&pn->l2tp_tunnel_list_lock);
+	idr_init(&pn->l2tp_tunnel_idr);
+	spin_lock_init(&pn->l2tp_tunnel_idr_lock);
 
 	for (hash = 0; hash < L2TP_HASH_SIZE_2; hash++)
 		INIT_HLIST_HEAD(&pn->l2tp_session_hlist[hash]);
@@ -1656,11 +1670,13 @@
 {
 	struct l2tp_net *pn = l2tp_pernet(net);
 	struct l2tp_tunnel *tunnel = NULL;
+	unsigned long tunnel_id, tmp;
 	int hash;
 
 	rcu_read_lock_bh();
-	list_for_each_entry_rcu(tunnel, &pn->l2tp_tunnel_list, list) {
-		l2tp_tunnel_delete(tunnel);
+	idr_for_each_entry_ul(&pn->l2tp_tunnel_idr, tunnel, tmp, tunnel_id) {
+		if (tunnel)
+			l2tp_tunnel_delete(tunnel);
 	}
 	rcu_read_unlock_bh();
 
@@ -1670,6 +1686,7 @@
 
 	for (hash = 0; hash < L2TP_HASH_SIZE_2; hash++)
 		WARN_ON_ONCE(!hlist_empty(&pn->l2tp_session_hlist[hash]));
+	idr_destroy(&pn->l2tp_tunnel_idr);
 }
 
 static struct pernet_operations l2tp_net_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/l2tp/l2tp_eth.c
+++ linux-xilinx-zynqmp-5.15.0/net/l2tp/l2tp_eth.c
@@ -136,6 +136,9 @@
 	/* checksums verified by L2TP */
 	skb->ip_summed = CHECKSUM_NONE;
 
+	/* drop outer flow-hash */
+	skb_clear_hash(skb);
+
 	skb_dst_drop(skb);
 	nf_reset_ct(skb);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/l2tp/l2tp_ip6.c
+++ linux-xilinx-zynqmp-5.15.0/net/l2tp/l2tp_ip6.c
@@ -255,8 +255,6 @@
 
 	if (tunnel)
 		l2tp_tunnel_delete(tunnel);
-
-	inet6_destroy_sock(sk);
 }
 
 static int l2tp_ip6_bind(struct sock *sk, struct sockaddr *uaddr, int addr_len)
@@ -502,13 +500,13 @@
 	struct ipcm6_cookie ipc6;
 	int addr_len = msg->msg_namelen;
 	int transhdrlen = 4; /* zero session-id */
-	int ulen = len + transhdrlen;
+	int ulen;
 	int err;
 
 	/* Rough check on arithmetic overflow,
 	 * better check is made in ip6_append_data().
 	 */
-	if (len > INT_MAX)
+	if (len > INT_MAX - transhdrlen)
 		return -EMSGSIZE;
 
 	/* Mirror BSD error message compatibility */
@@ -630,6 +628,7 @@
 
 back_from_confirm:
 	lock_sock(sk);
+	ulen = len + (skb_queue_empty(&sk->sk_write_queue) ? transhdrlen : 0);
 	err = ip6_append_data(sk, ip_generic_getfrag, msg,
 			      ulen, transhdrlen, &ipc6,
 			      &fl6, (struct rt6_info *)dst,
--- linux-xilinx-zynqmp-5.15.0.orig/net/l2tp/l2tp_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/l2tp/l2tp_netlink.c
@@ -115,7 +115,7 @@
 				  NLM_F_ACK, tunnel, cmd);
 
 	if (ret >= 0) {
-		ret = genlmsg_multicast_allns(family, msg, 0, 0, GFP_ATOMIC);
+		ret = genlmsg_multicast_allns(family, msg, 0, 0);
 		/* We don't care if no one is listening */
 		if (ret == -ESRCH)
 			ret = 0;
@@ -143,7 +143,7 @@
 				   NLM_F_ACK, session, cmd);
 
 	if (ret >= 0) {
-		ret = genlmsg_multicast_allns(family, msg, 0, 0, GFP_ATOMIC);
+		ret = genlmsg_multicast_allns(family, msg, 0, 0);
 		/* We don't care if no one is listening */
 		if (ret == -ESRCH)
 			ret = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/l2tp/l2tp_ppp.c
+++ linux-xilinx-zynqmp-5.15.0/net/l2tp/l2tp_ppp.c
@@ -651,54 +651,22 @@
 	return mtu - PPPOL2TP_HEADER_OVERHEAD;
 }
 
-/* connect() handler. Attach a PPPoX socket to a tunnel UDP socket
- */
-static int pppol2tp_connect(struct socket *sock, struct sockaddr *uservaddr,
-			    int sockaddr_len, int flags)
+static struct l2tp_tunnel *pppol2tp_tunnel_get(struct net *net,
+					       const struct l2tp_connect_info *info,
+					       bool *new_tunnel)
 {
-	struct sock *sk = sock->sk;
-	struct pppox_sock *po = pppox_sk(sk);
-	struct l2tp_session *session = NULL;
-	struct l2tp_connect_info info;
 	struct l2tp_tunnel *tunnel;
-	struct pppol2tp_session *ps;
-	struct l2tp_session_cfg cfg = { 0, };
-	bool drop_refcnt = false;
-	bool drop_tunnel = false;
-	bool new_session = false;
-	bool new_tunnel = false;
 	int error;
 
-	error = pppol2tp_sockaddr_get_info(uservaddr, sockaddr_len, &info);
-	if (error < 0)
-		return error;
+	*new_tunnel = false;
 
-	lock_sock(sk);
-
-	/* Check for already bound sockets */
-	error = -EBUSY;
-	if (sk->sk_state & PPPOX_CONNECTED)
-		goto end;
-
-	/* We don't supporting rebinding anyway */
-	error = -EALREADY;
-	if (sk->sk_user_data)
-		goto end; /* socket is already attached */
-
-	/* Don't bind if tunnel_id is 0 */
-	error = -EINVAL;
-	if (!info.tunnel_id)
-		goto end;
-
-	tunnel = l2tp_tunnel_get(sock_net(sk), info.tunnel_id);
-	if (tunnel)
-		drop_tunnel = true;
+	tunnel = l2tp_tunnel_get(net, info->tunnel_id);
 
 	/* Special case: create tunnel context if session_id and
 	 * peer_session_id is 0. Otherwise look up tunnel using supplied
 	 * tunnel id.
 	 */
-	if (!info.session_id && !info.peer_session_id) {
+	if (!info->session_id && !info->peer_session_id) {
 		if (!tunnel) {
 			struct l2tp_tunnel_cfg tcfg = {
 				.encap = L2TP_ENCAPTYPE_UDP,
@@ -707,40 +675,82 @@
 			/* Prevent l2tp_tunnel_register() from trying to set up
 			 * a kernel socket.
 			 */
-			if (info.fd < 0) {
-				error = -EBADF;
-				goto end;
-			}
+			if (info->fd < 0)
+				return ERR_PTR(-EBADF);
 
-			error = l2tp_tunnel_create(info.fd,
-						   info.version,
-						   info.tunnel_id,
-						   info.peer_tunnel_id, &tcfg,
+			error = l2tp_tunnel_create(info->fd,
+						   info->version,
+						   info->tunnel_id,
+						   info->peer_tunnel_id, &tcfg,
 						   &tunnel);
 			if (error < 0)
-				goto end;
+				return ERR_PTR(error);
 
 			l2tp_tunnel_inc_refcount(tunnel);
-			error = l2tp_tunnel_register(tunnel, sock_net(sk),
-						     &tcfg);
+			error = l2tp_tunnel_register(tunnel, net, &tcfg);
 			if (error < 0) {
 				kfree(tunnel);
-				goto end;
+				return ERR_PTR(error);
 			}
-			drop_tunnel = true;
-			new_tunnel = true;
+
+			*new_tunnel = true;
 		}
 	} else {
 		/* Error if we can't find the tunnel */
-		error = -ENOENT;
 		if (!tunnel)
-			goto end;
+			return ERR_PTR(-ENOENT);
 
 		/* Error if socket is not prepped */
-		if (!tunnel->sock)
-			goto end;
+		if (!tunnel->sock) {
+			l2tp_tunnel_dec_refcount(tunnel);
+			return ERR_PTR(-ENOENT);
+		}
 	}
 
+	return tunnel;
+}
+
+/* connect() handler. Attach a PPPoX socket to a tunnel UDP socket
+ */
+static int pppol2tp_connect(struct socket *sock, struct sockaddr *uservaddr,
+			    int sockaddr_len, int flags)
+{
+	struct sock *sk = sock->sk;
+	struct pppox_sock *po = pppox_sk(sk);
+	struct l2tp_session *session = NULL;
+	struct l2tp_connect_info info;
+	struct l2tp_tunnel *tunnel;
+	struct pppol2tp_session *ps;
+	struct l2tp_session_cfg cfg = { 0, };
+	bool drop_refcnt = false;
+	bool new_session = false;
+	bool new_tunnel = false;
+	int error;
+
+	error = pppol2tp_sockaddr_get_info(uservaddr, sockaddr_len, &info);
+	if (error < 0)
+		return error;
+
+	/* Don't bind if tunnel_id is 0 */
+	if (!info.tunnel_id)
+		return -EINVAL;
+
+	tunnel = pppol2tp_tunnel_get(sock_net(sk), &info, &new_tunnel);
+	if (IS_ERR(tunnel))
+		return PTR_ERR(tunnel);
+
+	lock_sock(sk);
+
+	/* Check for already bound sockets */
+	error = -EBUSY;
+	if (sk->sk_state & PPPOX_CONNECTED)
+		goto end;
+
+	/* We don't supporting rebinding anyway */
+	error = -EALREADY;
+	if (sk->sk_user_data)
+		goto end; /* socket is already attached */
+
 	if (tunnel->peer_tunnel_id == 0)
 		tunnel->peer_tunnel_id = info.peer_tunnel_id;
 
@@ -841,8 +851,7 @@
 	}
 	if (drop_refcnt)
 		l2tp_session_dec_refcount(session);
-	if (drop_tunnel)
-		l2tp_tunnel_dec_refcount(tunnel);
+	l2tp_tunnel_dec_refcount(tunnel);
 	release_sock(sk);
 
 	return error;
@@ -1348,11 +1357,11 @@
 	if (get_user(len, optlen))
 		return -EFAULT;
 
-	len = min_t(unsigned int, len, sizeof(int));
-
 	if (len < 0)
 		return -EINVAL;
 
+	len = min_t(unsigned int, len, sizeof(int));
+
 	err = -ENOTCONN;
 	if (!sk->sk_user_data)
 		goto end;
--- linux-xilinx-zynqmp-5.15.0.orig/net/l3mdev/l3mdev.c
+++ linux-xilinx-zynqmp-5.15.0/net/l3mdev/l3mdev.c
@@ -147,7 +147,7 @@
 
 	dev = dev_get_by_index_rcu(net, ifindex);
 	while (dev && !netif_is_l3_master(dev))
-		dev = netdev_master_upper_dev_get(dev);
+		dev = netdev_master_upper_dev_get_rcu(dev);
 
 	return dev ? dev->ifindex : 0;
 }
@@ -250,25 +250,19 @@
 	struct net_device *dev;
 	int rc = 0;
 
-	rcu_read_lock();
+	/* update flow ensures flowi_l3mdev is set when relevant */
+	if (!fl->flowi_l3mdev)
+		return 0;
 
-	dev = dev_get_by_index_rcu(net, fl->flowi_oif);
-	if (dev && netif_is_l3_master(dev) &&
-	    dev->l3mdev_ops->l3mdev_fib_table) {
-		arg->table = dev->l3mdev_ops->l3mdev_fib_table(dev);
-		rc = 1;
-		goto out;
-	}
+	rcu_read_lock();
 
-	dev = dev_get_by_index_rcu(net, fl->flowi_iif);
+	dev = dev_get_by_index_rcu(net, fl->flowi_l3mdev);
 	if (dev && netif_is_l3_master(dev) &&
 	    dev->l3mdev_ops->l3mdev_fib_table) {
 		arg->table = dev->l3mdev_ops->l3mdev_fib_table(dev);
 		rc = 1;
-		goto out;
 	}
 
-out:
 	rcu_read_unlock();
 
 	return rc;
@@ -277,31 +271,28 @@
 void l3mdev_update_flow(struct net *net, struct flowi *fl)
 {
 	struct net_device *dev;
-	int ifindex;
 
 	rcu_read_lock();
 
 	if (fl->flowi_oif) {
 		dev = dev_get_by_index_rcu(net, fl->flowi_oif);
 		if (dev) {
-			ifindex = l3mdev_master_ifindex_rcu(dev);
-			if (ifindex) {
-				fl->flowi_oif = ifindex;
-				fl->flowi_flags |= FLOWI_FLAG_SKIP_NH_OIF;
-				goto out;
-			}
+			if (!fl->flowi_l3mdev)
+				fl->flowi_l3mdev = l3mdev_master_ifindex_rcu(dev);
+
+			/* oif set to L3mdev directs lookup to its table;
+			 * reset to avoid oif match in fib_lookup
+			 */
+			if (netif_is_l3_master(dev))
+				fl->flowi_oif = 0;
+			goto out;
 		}
 	}
 
-	if (fl->flowi_iif) {
+	if (fl->flowi_iif > LOOPBACK_IFINDEX && !fl->flowi_l3mdev) {
 		dev = dev_get_by_index_rcu(net, fl->flowi_iif);
-		if (dev) {
-			ifindex = l3mdev_master_ifindex_rcu(dev);
-			if (ifindex) {
-				fl->flowi_iif = ifindex;
-				fl->flowi_flags |= FLOWI_FLAG_SKIP_NH_OIF;
-			}
-		}
+		if (dev)
+			fl->flowi_l3mdev = l3mdev_master_ifindex_rcu(dev);
 	}
 
 out:
--- linux-xilinx-zynqmp-5.15.0.orig/net/llc/af_llc.c
+++ linux-xilinx-zynqmp-5.15.0/net/llc/af_llc.c
@@ -226,6 +226,8 @@
 	}
 	dev_put(llc->dev);
 	sock_put(sk);
+	sock_orphan(sk);
+	sock->sk = NULL;
 	llc_sk_free(sk);
 out:
 	return 0;
@@ -275,6 +277,7 @@
 {
 	struct sock *sk = sock->sk;
 	struct llc_sock *llc = llc_sk(sk);
+	struct net_device *dev = NULL;
 	struct llc_sap *sap;
 	int rc = -EINVAL;
 
@@ -286,14 +289,14 @@
 		goto out;
 	rc = -ENODEV;
 	if (sk->sk_bound_dev_if) {
-		llc->dev = dev_get_by_index(&init_net, sk->sk_bound_dev_if);
-		if (llc->dev && addr->sllc_arphrd != llc->dev->type) {
-			dev_put(llc->dev);
-			llc->dev = NULL;
+		dev = dev_get_by_index(&init_net, sk->sk_bound_dev_if);
+		if (dev && addr->sllc_arphrd != dev->type) {
+			dev_put(dev);
+			dev = NULL;
 		}
 	} else
-		llc->dev = dev_getfirstbyhwtype(&init_net, addr->sllc_arphrd);
-	if (!llc->dev)
+		dev = dev_getfirstbyhwtype(&init_net, addr->sllc_arphrd);
+	if (!dev)
 		goto out;
 	rc = -EUSERS;
 	llc->laddr.lsap = llc_ui_autoport();
@@ -303,6 +306,11 @@
 	sap = llc_sap_open(llc->laddr.lsap, NULL);
 	if (!sap)
 		goto out;
+
+	/* Note: We do not expect errors from this point. */
+	llc->dev = dev;
+	dev = NULL;
+
 	memcpy(llc->laddr.mac, llc->dev->dev_addr, IFHWADDRLEN);
 	memcpy(&llc->addr, addr, sizeof(llc->addr));
 	/* assign new connection to its SAP */
@@ -310,6 +318,7 @@
 	sock_reset_flag(sk, SOCK_ZAPPED);
 	rc = 0;
 out:
+	dev_put(dev);
 	return rc;
 }
 
@@ -332,6 +341,7 @@
 	struct sockaddr_llc *addr = (struct sockaddr_llc *)uaddr;
 	struct sock *sk = sock->sk;
 	struct llc_sock *llc = llc_sk(sk);
+	struct net_device *dev = NULL;
 	struct llc_sap *sap;
 	int rc = -EINVAL;
 
@@ -347,25 +357,27 @@
 	rc = -ENODEV;
 	rcu_read_lock();
 	if (sk->sk_bound_dev_if) {
-		llc->dev = dev_get_by_index_rcu(&init_net, sk->sk_bound_dev_if);
-		if (llc->dev) {
+		dev = dev_get_by_index_rcu(&init_net, sk->sk_bound_dev_if);
+		if (dev) {
 			if (is_zero_ether_addr(addr->sllc_mac))
-				memcpy(addr->sllc_mac, llc->dev->dev_addr,
+				memcpy(addr->sllc_mac, dev->dev_addr,
 				       IFHWADDRLEN);
-			if (addr->sllc_arphrd != llc->dev->type ||
+			if (addr->sllc_arphrd != dev->type ||
 			    !ether_addr_equal(addr->sllc_mac,
-					      llc->dev->dev_addr)) {
+					      dev->dev_addr)) {
 				rc = -EINVAL;
-				llc->dev = NULL;
+				dev = NULL;
 			}
 		}
-	} else
-		llc->dev = dev_getbyhwaddr_rcu(&init_net, addr->sllc_arphrd,
+	} else {
+		dev = dev_getbyhwaddr_rcu(&init_net, addr->sllc_arphrd,
 					   addr->sllc_mac);
-	dev_hold(llc->dev);
+	}
+	dev_hold(dev);
 	rcu_read_unlock();
-	if (!llc->dev)
+	if (!dev)
 		goto out;
+
 	if (!addr->sllc_sap) {
 		rc = -EUSERS;
 		addr->sllc_sap = llc_ui_autoport();
@@ -397,6 +409,11 @@
 			goto out_put;
 		}
 	}
+
+	/* Note: We do not expect errors from this point. */
+	llc->dev = dev;
+	dev = NULL;
+
 	llc->laddr.lsap = addr->sllc_sap;
 	memcpy(llc->laddr.mac, addr->sllc_mac, IFHWADDRLEN);
 	memcpy(&llc->addr, addr, sizeof(llc->addr));
@@ -407,6 +424,7 @@
 out_put:
 	llc_sap_put(sap);
 out:
+	dev_put(dev);
 	release_sock(sk);
 	return rc;
 }
@@ -565,7 +583,8 @@
 
 	add_wait_queue(sk_sleep(sk), &wait);
 	while (1) {
-		if (sk_wait_event(sk, &timeout, sk->sk_state == TCP_CLOSE, &wait))
+		if (sk_wait_event(sk, &timeout,
+				  READ_ONCE(sk->sk_state) == TCP_CLOSE, &wait))
 			break;
 		rc = -ERESTARTSYS;
 		if (signal_pending(current))
@@ -585,7 +604,8 @@
 
 	add_wait_queue(sk_sleep(sk), &wait);
 	while (1) {
-		if (sk_wait_event(sk, &timeout, sk->sk_state != TCP_SYN_SENT, &wait))
+		if (sk_wait_event(sk, &timeout,
+				  READ_ONCE(sk->sk_state) != TCP_SYN_SENT, &wait))
 			break;
 		if (signal_pending(current) || !timeout)
 			break;
@@ -604,7 +624,7 @@
 	while (1) {
 		rc = 0;
 		if (sk_wait_event(sk, &timeout,
-				  (sk->sk_shutdown & RCV_SHUTDOWN) ||
+				  (READ_ONCE(sk->sk_shutdown) & RCV_SHUTDOWN) ||
 				  (!llc_data_accept_state(llc->state) &&
 				   !llc->remote_busy_flag &&
 				   !llc->p_flag), &wait))
@@ -908,14 +928,15 @@
  */
 static int llc_ui_sendmsg(struct socket *sock, struct msghdr *msg, size_t len)
 {
+	DECLARE_SOCKADDR(struct sockaddr_llc *, addr, msg->msg_name);
 	struct sock *sk = sock->sk;
 	struct llc_sock *llc = llc_sk(sk);
-	DECLARE_SOCKADDR(struct sockaddr_llc *, addr, msg->msg_name);
 	int flags = msg->msg_flags;
 	int noblock = flags & MSG_DONTWAIT;
+	int rc = -EINVAL, copied = 0, hdrlen, hh_len;
 	struct sk_buff *skb = NULL;
+	struct net_device *dev;
 	size_t size = 0;
-	int rc = -EINVAL, copied = 0, hdrlen;
 
 	dprintk("%s: sending from %02X to %02X\n", __func__,
 		llc->laddr.lsap, llc->daddr.lsap);
@@ -935,22 +956,29 @@
 		if (rc)
 			goto out;
 	}
-	hdrlen = llc->dev->hard_header_len + llc_ui_header_len(sk, addr);
+	dev = llc->dev;
+	hh_len = LL_RESERVED_SPACE(dev);
+	hdrlen = llc_ui_header_len(sk, addr);
 	size = hdrlen + len;
-	if (size > llc->dev->mtu)
-		size = llc->dev->mtu;
+	size = min_t(size_t, size, READ_ONCE(dev->mtu));
 	copied = size - hdrlen;
 	rc = -EINVAL;
 	if (copied < 0)
 		goto out;
 	release_sock(sk);
-	skb = sock_alloc_send_skb(sk, size, noblock, &rc);
+	skb = sock_alloc_send_skb(sk, hh_len + size, noblock, &rc);
 	lock_sock(sk);
 	if (!skb)
 		goto out;
-	skb->dev      = llc->dev;
+	if (sock_flag(sk, SOCK_ZAPPED) ||
+	    llc->dev != dev ||
+	    hdrlen != llc_ui_header_len(sk, addr) ||
+	    hh_len != LL_RESERVED_SPACE(dev) ||
+	    size > READ_ONCE(dev->mtu))
+		goto out;
+	skb->dev      = dev;
 	skb->protocol = llc_proto_type(addr->sllc_arphrd);
-	skb_reserve(skb, hdrlen);
+	skb_reserve(skb, hh_len + hdrlen);
 	rc = memcpy_from_msg(skb_put(skb, copied), msg, copied);
 	if (rc)
 		goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/net/llc/llc_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/llc/llc_core.c
@@ -135,22 +135,15 @@
 	.func = llc_rcv,
 };
 
-static struct packet_type llc_tr_packet_type __read_mostly = {
-	.type = cpu_to_be16(ETH_P_TR_802_2),
-	.func = llc_rcv,
-};
-
 static int __init llc_init(void)
 {
 	dev_add_pack(&llc_packet_type);
-	dev_add_pack(&llc_tr_packet_type);
 	return 0;
 }
 
 static void __exit llc_exit(void)
 {
 	dev_remove_pack(&llc_packet_type);
-	dev_remove_pack(&llc_tr_packet_type);
 }
 
 module_init(llc_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/llc/llc_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/llc/llc_input.c
@@ -124,11 +124,17 @@
 	if (unlikely(!pskb_may_pull(skb, llc_len)))
 		return 0;
 
-	skb->transport_header += llc_len;
 	skb_pull(skb, llc_len);
+	skb_reset_transport_header(skb);
 	if (skb->protocol == htons(ETH_P_802_2)) {
-		__be16 pdulen = eth_hdr(skb)->h_proto;
-		s32 data_size = ntohs(pdulen) - llc_len;
+		__be16 pdulen;
+		s32 data_size;
+
+		if (skb->mac_len < ETH_HLEN)
+			return 0;
+
+		pdulen = eth_hdr(skb)->h_proto;
+		data_size = ntohs(pdulen) - llc_len;
 
 		if (data_size < 0 ||
 		    !pskb_may_pull(skb, data_size))
@@ -163,9 +169,6 @@
 	void (*sta_handler)(struct sk_buff *skb);
 	void (*sap_handler)(struct llc_sap *sap, struct sk_buff *skb);
 
-	if (!net_eq(dev_net(dev), &init_net))
-		goto drop;
-
 	/*
 	 * When the interface is in promisc. mode, drop all the crap that it
 	 * receives, do not try to analyse it.
--- linux-xilinx-zynqmp-5.15.0.orig/net/llc/llc_s_ac.c
+++ linux-xilinx-zynqmp-5.15.0/net/llc/llc_s_ac.c
@@ -24,7 +24,7 @@
 #include <net/llc_s_ac.h>
 #include <net/llc_s_ev.h>
 #include <net/llc_sap.h>
-
+#include <net/sock.h>
 
 /**
  *	llc_sap_action_unitdata_ind - forward UI PDU to network layer
@@ -40,6 +40,26 @@
 	return 0;
 }
 
+static int llc_prepare_and_xmit(struct sk_buff *skb)
+{
+	struct llc_sap_state_ev *ev = llc_sap_ev(skb);
+	struct sk_buff *nskb;
+	int rc;
+
+	rc = llc_mac_hdr_init(skb, ev->saddr.mac, ev->daddr.mac);
+	if (rc)
+		return rc;
+
+	nskb = skb_clone(skb, GFP_ATOMIC);
+	if (!nskb)
+		return -ENOMEM;
+
+	if (skb->sk)
+		skb_set_owner_w(nskb, skb->sk);
+
+	return dev_queue_xmit(nskb);
+}
+
 /**
  *	llc_sap_action_send_ui - sends UI PDU resp to UNITDATA REQ to MAC layer
  *	@sap: SAP
@@ -52,17 +72,12 @@
 int llc_sap_action_send_ui(struct llc_sap *sap, struct sk_buff *skb)
 {
 	struct llc_sap_state_ev *ev = llc_sap_ev(skb);
-	int rc;
 
 	llc_pdu_header_init(skb, LLC_PDU_TYPE_U, ev->saddr.lsap,
 			    ev->daddr.lsap, LLC_PDU_CMD);
 	llc_pdu_init_as_ui_cmd(skb);
-	rc = llc_mac_hdr_init(skb, ev->saddr.mac, ev->daddr.mac);
-	if (likely(!rc)) {
-		skb_get(skb);
-		rc = dev_queue_xmit(skb);
-	}
-	return rc;
+
+	return llc_prepare_and_xmit(skb);
 }
 
 /**
@@ -77,17 +92,12 @@
 int llc_sap_action_send_xid_c(struct llc_sap *sap, struct sk_buff *skb)
 {
 	struct llc_sap_state_ev *ev = llc_sap_ev(skb);
-	int rc;
 
 	llc_pdu_header_init(skb, LLC_PDU_TYPE_U_XID, ev->saddr.lsap,
 			    ev->daddr.lsap, LLC_PDU_CMD);
 	llc_pdu_init_as_xid_cmd(skb, LLC_XID_NULL_CLASS_2, 0);
-	rc = llc_mac_hdr_init(skb, ev->saddr.mac, ev->daddr.mac);
-	if (likely(!rc)) {
-		skb_get(skb);
-		rc = dev_queue_xmit(skb);
-	}
-	return rc;
+
+	return llc_prepare_and_xmit(skb);
 }
 
 /**
@@ -133,17 +143,12 @@
 int llc_sap_action_send_test_c(struct llc_sap *sap, struct sk_buff *skb)
 {
 	struct llc_sap_state_ev *ev = llc_sap_ev(skb);
-	int rc;
 
 	llc_pdu_header_init(skb, LLC_PDU_TYPE_U, ev->saddr.lsap,
 			    ev->daddr.lsap, LLC_PDU_CMD);
 	llc_pdu_init_as_test_cmd(skb);
-	rc = llc_mac_hdr_init(skb, ev->saddr.mac, ev->daddr.mac);
-	if (likely(!rc)) {
-		skb_get(skb);
-		rc = dev_queue_xmit(skb);
-	}
-	return rc;
+
+	return llc_prepare_and_xmit(skb);
 }
 
 int llc_sap_action_send_test_r(struct llc_sap *sap, struct sk_buff *skb)
@@ -153,6 +158,9 @@
 	int rc = 1;
 	u32 data_size;
 
+	if (skb->mac_len < ETH_HLEN)
+		return 1;
+
 	llc_pdu_decode_sa(skb, mac_da);
 	llc_pdu_decode_da(skb, mac_sa);
 	llc_pdu_decode_ssap(skb, &dsap);
--- linux-xilinx-zynqmp-5.15.0.orig/net/llc/llc_station.c
+++ linux-xilinx-zynqmp-5.15.0/net/llc/llc_station.c
@@ -76,6 +76,9 @@
 	u32 data_size;
 	struct sk_buff *nskb;
 
+	if (skb->mac_len < ETH_HLEN)
+		goto out;
+
 	/* The test request command is type U (llc_len = 3) */
 	data_size = ntohs(eth_hdr(skb)->h_proto) - 3;
 	nskb = llc_alloc_frame(NULL, skb->dev, LLC_PDU_TYPE_U, data_size);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/Kconfig
@@ -86,7 +86,7 @@
 
 config MAC80211_MESSAGE_TRACING
 	bool "Trace all mac80211 debug messages"
-	depends on MAC80211
+	depends on MAC80211 && TRACING
 	help
 	  Select this option to have mac80211 register the
 	  mac80211_msg trace subsystem with tracepoints to
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/agg-rx.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/agg-rx.c
@@ -9,7 +9,7 @@
  * Copyright 2007, Michael Wu <flamingice@sourmilk.net>
  * Copyright 2007-2010, Intel Corporation
  * Copyright(c) 2015-2017 Intel Deutschland GmbH
- * Copyright (C) 2018-2020 Intel Corporation
+ * Copyright (C) 2018-2021 Intel Corporation
  */
 
 /**
@@ -191,7 +191,8 @@
 	sband = ieee80211_get_sband(sdata);
 	if (!sband)
 		return;
-	he_cap = ieee80211_get_he_iftype_cap(sband, sdata->vif.type);
+	he_cap = ieee80211_get_he_iftype_cap(sband,
+					     ieee80211_vif_type_p2p(&sdata->vif));
 	if (!he_cap)
 		return;
 
@@ -309,7 +310,7 @@
 	}
 
 	if (sta->sta.he_cap.has_he)
-		max_buf_size = IEEE80211_MAX_AMPDU_BUF;
+		max_buf_size = IEEE80211_MAX_AMPDU_BUF_HE;
 	else
 		max_buf_size = IEEE80211_MAX_AMPDU_BUF_HT;
 
@@ -477,7 +478,7 @@
 				     size_t len)
 {
 	u16 capab, tid, timeout, ba_policy, buf_size, start_seq_num;
-	struct ieee802_11_elems elems = { };
+	struct ieee802_11_elems *elems = NULL;
 	u8 dialog_token;
 	int ies_len;
 
@@ -495,16 +496,18 @@
 	ies_len = len - offsetof(struct ieee80211_mgmt,
 				 u.action.u.addba_req.variable);
 	if (ies_len) {
-		ieee802_11_parse_elems(mgmt->u.action.u.addba_req.variable,
-                                ies_len, true, &elems, mgmt->bssid, NULL);
-		if (elems.parse_error)
-			return;
+		elems = ieee802_11_parse_elems(mgmt->u.action.u.addba_req.variable,
+					       ies_len, true, mgmt->bssid, NULL);
+		if (!elems || elems->parse_error)
+			goto free;
 	}
 
 	__ieee80211_start_rx_ba_session(sta, dialog_token, timeout,
 					start_seq_num, ba_policy, tid,
 					buf_size, true, false,
-					elems.addba_ext_ie);
+					elems ? elems->addba_ext_ie : NULL);
+free:
+	kfree(elems);
 }
 
 void ieee80211_manage_rx_ba_offl(struct ieee80211_vif *vif,
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/agg-tx.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/agg-tx.c
@@ -9,7 +9,7 @@
  * Copyright 2007, Michael Wu <flamingice@sourmilk.net>
  * Copyright 2007-2010, Intel Corporation
  * Copyright(c) 2015-2017 Intel Deutschland GmbH
- * Copyright (C) 2018 - 2020 Intel Corporation
+ * Copyright (C) 2018 - 2022 Intel Corporation
  */
 
 #include <linux/ieee80211.h>
@@ -106,7 +106,7 @@
 	mgmt->u.action.u.addba_req.start_seq_num =
 					cpu_to_le16(start_seq_num << 4);
 
-	ieee80211_tx_skb(sdata, skb);
+	ieee80211_tx_skb_tid(sdata, skb, tid);
 }
 
 void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn)
@@ -213,6 +213,8 @@
 	struct ieee80211_txq *txq = sta->sta.txq[tid];
 	struct txq_info *txqi;
 
+	lockdep_assert_held(&sta->ampdu_mlme.mtx);
+
 	if (!txq)
 		return;
 
@@ -290,7 +292,6 @@
 	ieee80211_assign_tid_tx(sta, tid, NULL);
 
 	ieee80211_agg_splice_finish(sta->sdata, tid);
-	ieee80211_agg_start_txq(sta, tid, false);
 
 	kfree_rcu(tid_tx, rcu_head);
 }
@@ -480,8 +481,7 @@
 
 	/* send AddBA request */
 	ieee80211_send_addba_request(sdata, sta->sta.addr, tid,
-				     tid_tx->dialog_token,
-				     sta->tid_seq[tid] >> 4,
+				     tid_tx->dialog_token, tid_tx->ssn,
 				     buf_size, tid_tx->timeout);
 
 	WARN_ON(test_and_set_bit(HT_AGG_STATE_SENT_ADDBA, &tid_tx->state));
@@ -523,6 +523,7 @@
 
 	params.ssn = sta->tid_seq[tid] >> 4;
 	ret = drv_ampdu_action(local, sdata, &params);
+	tid_tx->ssn = params.ssn;
 	if (ret == IEEE80211_AMPDU_TX_START_DELAY_ADDBA) {
 		return;
 	} else if (ret == IEEE80211_AMPDU_TX_START_IMMEDIATE) {
@@ -625,6 +626,14 @@
 		return -EINVAL;
 	}
 
+	if (test_sta_flag(sta, WLAN_STA_MFP) &&
+	    !test_sta_flag(sta, WLAN_STA_AUTHORIZED)) {
+		ht_dbg(sdata,
+		       "MFP STA not authorized - deny BA session request %pM tid %d\n",
+		       sta->sta.addr, tid);
+		return -EINVAL;
+	}
+
 	/*
 	 * 802.11n-2009 11.5.1.1: If the initiating STA is an HT STA, is a
 	 * member of an IBSS, and has no other existing Block Ack agreement
@@ -889,6 +898,7 @@
 {
 	struct ieee80211_sub_if_data *sdata = sta->sdata;
 	bool send_delba = false;
+	bool start_txq = false;
 
 	ht_dbg(sdata, "Stopping Tx BA session for %pM tid %d\n",
 	       sta->sta.addr, tid);
@@ -906,10 +916,14 @@
 		send_delba = true;
 
 	ieee80211_remove_tid_tx(sta, tid);
+	start_txq = true;
 
  unlock_sta:
 	spin_unlock_bh(&sta->lock);
 
+	if (start_txq)
+		ieee80211_agg_start_txq(sta, tid, false);
+
 	if (send_delba)
 		ieee80211_send_delba(sdata, sta->sta.addr, tid,
 			WLAN_BACK_INITIATOR, WLAN_REASON_QSTA_NOT_USE);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/airtime.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/airtime.c
@@ -457,6 +457,9 @@
 			 (status->encoding == RX_ENC_HE && streams > 8)))
 		return 0;
 
+	if (idx >= MCS_GROUP_RATES)
+		return 0;
+
 	duration = airtime_mcs_groups[group].duration[idx];
 	duration <<= airtime_mcs_groups[group].shift;
 	*overhead = 36 + (streams << 2);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/cfg.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/cfg.c
@@ -80,7 +80,8 @@
 	}
 
 	/* also validate MU-MIMO change */
-	monitor_sdata = rtnl_dereference(local->monitor_sdata);
+	monitor_sdata = wiphy_dereference(local->hw.wiphy,
+					  local->monitor_sdata);
 
 	if (!monitor_sdata &&
 	    (params->vht_mumimo_groups || params->vht_mumimo_follow_addr))
@@ -510,6 +511,9 @@
 		sta->cipher_scheme = cs;
 
 	err = ieee80211_key_link(key, sdata, sta);
+	/* KRACK protection, shouldn't happen but just silently accept key */
+	if (err == -EALREADY)
+		err = 0;
 
  out_unlock:
 	mutex_unlock(&local->sta_mtx);
@@ -810,7 +814,8 @@
 
 	mutex_lock(&local->mtx);
 	if (local->use_chanctx) {
-		sdata = rtnl_dereference(local->monitor_sdata);
+		sdata = wiphy_dereference(local->hw.wiphy,
+					  local->monitor_sdata);
 		if (sdata) {
 			ieee80211_vif_release_channel(sdata);
 			ret = ieee80211_vif_use_channel(sdata, chandef,
@@ -1224,7 +1229,10 @@
 	return 0;
 
 error:
+	mutex_lock(&local->mtx);
 	ieee80211_vif_release_channel(sdata);
+	mutex_unlock(&local->mtx);
+
 	return err;
 }
 
@@ -1840,15 +1848,14 @@
 		}
 
 		if (sta->sdata->vif.type == NL80211_IFTYPE_AP_VLAN &&
-		    sta->sdata->u.vlan.sta) {
-			ieee80211_clear_fast_rx(sta);
+		    sta->sdata->u.vlan.sta)
 			RCU_INIT_POINTER(sta->sdata->u.vlan.sta, NULL);
-		}
 
 		if (test_sta_flag(sta, WLAN_STA_AUTHORIZED))
 			ieee80211_vif_dec_num_mcast(sta->sdata);
 
 		sta->sdata = vlansdata;
+		ieee80211_check_fast_rx(sta);
 		ieee80211_check_fast_xmit(sta);
 
 		if (test_sta_flag(sta, WLAN_STA_AUTHORIZED)) {
@@ -2105,14 +2112,12 @@
 		const struct mesh_setup *setup)
 {
 	u8 *new_ie;
-	const u8 *old_ie;
 	struct ieee80211_sub_if_data *sdata = container_of(ifmsh,
 					struct ieee80211_sub_if_data, u.mesh);
 	int i;
 
 	/* allocate information elements */
 	new_ie = NULL;
-	old_ie = ifmsh->ie;
 
 	if (setup->ie_len) {
 		new_ie = kmemdup(setup->ie, setup->ie_len,
@@ -2122,7 +2127,6 @@
 	}
 	ifmsh->ie_len = setup->ie_len;
 	ifmsh->ie = new_ie;
-	kfree(old_ie);
 
 	/* now copy the rest of the setup parameters */
 	ifmsh->mesh_id_len = setup->mesh_id_len;
@@ -2338,6 +2342,17 @@
 	if (!sband)
 		return -EINVAL;
 
+	if (params->basic_rates) {
+		if (!ieee80211_parse_bitrates(&sdata->vif.bss_conf.chandef,
+					      wiphy->bands[sband->band],
+					      params->basic_rates,
+					      params->basic_rates_len,
+					      &sdata->vif.bss_conf.basic_rates))
+			return -EINVAL;
+		changed |= BSS_CHANGED_BASIC_RATES;
+		ieee80211_check_rate_mask(sdata);
+	}
+
 	if (params->use_cts_prot >= 0) {
 		sdata->vif.bss_conf.use_cts_prot = params->use_cts_prot;
 		changed |= BSS_CHANGED_ERP_CTS_PROT;
@@ -2361,16 +2376,6 @@
 		changed |= BSS_CHANGED_ERP_SLOT;
 	}
 
-	if (params->basic_rates) {
-		ieee80211_parse_bitrates(&sdata->vif.bss_conf.chandef,
-					 wiphy->bands[sband->band],
-					 params->basic_rates,
-					 params->basic_rates_len,
-					 &sdata->vif.bss_conf.basic_rates);
-		changed |= BSS_CHANGED_BASIC_RATES;
-		ieee80211_check_rate_mask(sdata);
-	}
-
 	if (params->ap_isolate >= 0) {
 		if (params->ap_isolate)
 			sdata->flags |= IEEE80211_SDATA_DONT_BRIDGE_PACKETS;
@@ -2669,7 +2674,8 @@
 		sdata = IEEE80211_WDEV_TO_SUB_IF(wdev);
 
 		if (sdata->vif.type == NL80211_IFTYPE_MONITOR) {
-			sdata = rtnl_dereference(local->monitor_sdata);
+			sdata = wiphy_dereference(local->hw.wiphy,
+						  local->monitor_sdata);
 			if (!sdata)
 				return -EOPNOTSUPP;
 		}
@@ -2729,7 +2735,8 @@
 	mutex_unlock(&local->iflist_mtx);
 
 	if (has_monitor) {
-		sdata = rtnl_dereference(local->monitor_sdata);
+		sdata = wiphy_dereference(local->hw.wiphy,
+					  local->monitor_sdata);
 		if (sdata) {
 			sdata->user_power_level = local->user_power_level;
 			if (txp_type != sdata->vif.bss_conf.txpower_type)
@@ -2750,7 +2757,8 @@
 	struct ieee80211_local *local = wiphy_priv(wiphy);
 	struct ieee80211_sub_if_data *sdata = IEEE80211_WDEV_TO_SUB_IF(wdev);
 
-	if (local->ops->get_txpower)
+	if (local->ops->get_txpower &&
+	    (sdata->flags & IEEE80211_SDATA_IN_DRIVER))
 		return drv_get_txpower(local, sdata, dbm);
 
 	if (!local->use_chanctx)
@@ -2758,6 +2766,10 @@
 	else
 		*dbm = sdata->vif.bss_conf.txpower;
 
+	/* INT_MIN indicates no power level was set yet */
+	if (*dbm == INT_MIN)
+		return -EINVAL;
+
 	return 0;
 }
 
@@ -3380,9 +3392,6 @@
 	case NL80211_IFTYPE_MESH_POINT: {
 		struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
 
-		if (params->chandef.width != sdata->vif.bss_conf.chandef.width)
-			return -EINVAL;
-
 		/* changes into another band are not supported */
 		if (sdata->vif.bss_conf.chandef.chan->band !=
 		    params->chandef.chan->band)
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/chan.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/chan.c
@@ -563,7 +563,7 @@
 	ctx->conf.rx_chains_dynamic = 1;
 	ctx->mode = mode;
 	ctx->conf.radar_enabled = false;
-	ieee80211_recalc_chanctx_min_def(local, ctx);
+	_ieee80211_recalc_chanctx_min_def(local, ctx);
 
 	return ctx;
 }
@@ -1746,12 +1746,9 @@
 
 	if (new_ctx->replace_state == IEEE80211_CHANCTX_REPLACE_NONE) {
 		if (old_ctx)
-			err = ieee80211_vif_use_reserved_reassign(sdata);
-		else
-			err = ieee80211_vif_use_reserved_assign(sdata);
+			return ieee80211_vif_use_reserved_reassign(sdata);
 
-		if (err)
-			return err;
+		return ieee80211_vif_use_reserved_assign(sdata);
 	}
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/driver-ops.h
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/driver-ops.h
@@ -1219,8 +1219,11 @@
 {
 	struct ieee80211_sub_if_data *sdata = vif_to_sdata(txq->txq.vif);
 
-	if (local->in_reconfig)
+	/* In reconfig don't transmit now, but mark for waking later */
+	if (local->in_reconfig) {
+		set_bit(IEEE80211_TXQ_STOP_NETIF_TX, &txq->flags);
 		return;
+	}
 
 	if (!check_sdata_in_driver(sdata))
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/he.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/he.c
@@ -223,15 +223,21 @@
 
 	if (!he_spr_ie_elem)
 		return;
+
+	he_obss_pd->sr_ctrl = he_spr_ie_elem->he_sr_control;
 	data = he_spr_ie_elem->optional;
 
 	if (he_spr_ie_elem->he_sr_control &
 	    IEEE80211_HE_SPR_NON_SRG_OFFSET_PRESENT)
-		data++;
+		he_obss_pd->non_srg_max_offset = *data++;
+
 	if (he_spr_ie_elem->he_sr_control &
 	    IEEE80211_HE_SPR_SRG_INFORMATION_PRESENT) {
-		he_obss_pd->max_offset = *data++;
 		he_obss_pd->min_offset = *data++;
+		he_obss_pd->max_offset = *data++;
+		memcpy(he_obss_pd->bss_color_bitmap, data, 8);
+		data += 8;
+		memcpy(he_obss_pd->partial_bssid_bitmap, data, 8);
 		he_obss_pd->enable = true;
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/ibss.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/ibss.c
@@ -9,7 +9,7 @@
  * Copyright 2009, Johannes Berg <johannes@sipsolutions.net>
  * Copyright 2013-2014  Intel Mobile Communications GmbH
  * Copyright(c) 2016 Intel Deutschland GmbH
- * Copyright(c) 2018-2020 Intel Corporation
+ * Copyright(c) 2018-2021 Intel Corporation
  */
 
 #include <linux/delay.h>
@@ -534,6 +534,10 @@
 
 	sdata_assert_lock(sdata);
 
+	/* When not connected/joined, sending CSA doesn't make sense. */
+	if (ifibss->state != IEEE80211_IBSS_MLME_JOINED)
+		return -ENOLINK;
+
 	/* update cfg80211 bss information with the new channel */
 	if (!is_zero_ether_addr(ifibss->bssid)) {
 		cbss = cfg80211_get_bss(sdata->local->hw.wiphy,
@@ -1589,7 +1593,7 @@
 				    struct ieee80211_rx_status *rx_status)
 {
 	size_t baselen;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 
 	BUILD_BUG_ON(offsetof(typeof(mgmt->u.probe_resp), variable) !=
 		     offsetof(typeof(mgmt->u.beacon), variable));
@@ -1602,10 +1606,14 @@
 	if (baselen > len)
 		return;
 
-	ieee802_11_parse_elems(mgmt->u.probe_resp.variable, len - baselen,
-			       false, &elems, mgmt->bssid, NULL);
-
-	ieee80211_rx_bss_info(sdata, mgmt, len, rx_status, &elems);
+	elems = ieee802_11_parse_elems(mgmt->u.probe_resp.variable,
+				       len - baselen, false,
+				       mgmt->bssid, NULL);
+
+	if (elems) {
+		ieee80211_rx_bss_info(sdata, mgmt, len, rx_status, elems);
+		kfree(elems);
+	}
 }
 
 void ieee80211_ibss_rx_queued_mgmt(struct ieee80211_sub_if_data *sdata,
@@ -1614,7 +1622,7 @@
 	struct ieee80211_rx_status *rx_status;
 	struct ieee80211_mgmt *mgmt;
 	u16 fc;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	int ies_len;
 
 	rx_status = IEEE80211_SKB_RXCB(skb);
@@ -1651,15 +1659,16 @@
 			if (ies_len < 0)
 				break;
 
-			ieee802_11_parse_elems(
+			elems = ieee802_11_parse_elems(
 				mgmt->u.action.u.chan_switch.variable,
-				ies_len, true, &elems, mgmt->bssid, NULL);
-
-			if (elems.parse_error)
-				break;
+				ies_len, true, mgmt->bssid, NULL);
 
-			ieee80211_rx_mgmt_spectrum_mgmt(sdata, mgmt, skb->len,
-							rx_status, &elems);
+			if (elems && !elems->parse_error)
+				ieee80211_rx_mgmt_spectrum_mgmt(sdata, mgmt,
+								skb->len,
+								rx_status,
+								elems);
+			kfree(elems);
 			break;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/ieee80211_i.h
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/ieee80211_i.h
@@ -113,7 +113,7 @@
 };
 
 /**
- * enum ieee80211_corrupt_data_flags - BSS data corruption flags
+ * enum ieee80211_bss_corrupt_data_flags - BSS data corruption flags
  * @IEEE80211_BSS_CORRUPT_BEACON: last beacon frame received was corrupted
  * @IEEE80211_BSS_CORRUPT_PROBE_RESP: last probe response received was corrupted
  *
@@ -126,7 +126,7 @@
 };
 
 /**
- * enum ieee80211_valid_data_flags - BSS valid data flags
+ * enum ieee80211_bss_valid_data_flags - BSS valid data flags
  * @IEEE80211_BSS_VALID_WMM: WMM/UAPSD data was gathered from non-corrupt IE
  * @IEEE80211_BSS_VALID_RATES: Supported rates were gathered from non-corrupt IE
  * @IEEE80211_BSS_VALID_ERP: ERP flag was gathered from non-corrupt IE
@@ -376,7 +376,7 @@
 
 	u8 key[WLAN_KEY_LEN_WEP104];
 	u8 key_len, key_idx;
-	bool done;
+	bool done, waiting;
 	bool peer_confirmed;
 	bool timeout_started;
 
@@ -631,10 +631,9 @@
  */
 struct ieee802_11_elems;
 struct ieee80211_mesh_sync_ops {
-	void (*rx_bcn_presp)(struct ieee80211_sub_if_data *sdata,
-			     u16 stype,
-			     struct ieee80211_mgmt *mgmt,
-			     struct ieee802_11_elems *elems,
+	void (*rx_bcn_presp)(struct ieee80211_sub_if_data *sdata, u16 stype,
+			     struct ieee80211_mgmt *mgmt, unsigned int len,
+			     const struct ieee80211_meshconf_ie *mesh_cfg,
 			     struct ieee80211_rx_status *rx_status);
 
 	/* should be called with beacon_data under RCU read lock */
@@ -648,6 +647,26 @@
 	struct cfg80211_csa_settings settings;
 };
 
+/**
+ * struct mesh_table
+ *
+ * @known_gates: list of known mesh gates and their mpaths by the station. The
+ * gate's mpath may or may not be resolved and active.
+ * @gates_lock: protects updates to known_gates
+ * @rhead: the rhashtable containing struct mesh_paths, keyed by dest addr
+ * @walk_head: linked list containing all mesh_path objects
+ * @walk_lock: lock protecting walk_head
+ * @entries: number of entries in the table
+ */
+struct mesh_table {
+	struct hlist_head known_gates;
+	spinlock_t gates_lock;
+	struct rhashtable rhead;
+	struct hlist_head walk_head;
+	spinlock_t walk_lock;
+	atomic_t entries;		/* Up to MAX_MESH_NEIGHBOURS */
+};
+
 struct ieee80211_if_mesh {
 	struct timer_list housekeeping_timer;
 	struct timer_list mesh_path_timer;
@@ -722,8 +741,8 @@
 	/* offset from skb->data while building IE */
 	int meshconf_offset;
 
-	struct mesh_table *mesh_paths;
-	struct mesh_table *mpp_paths; /* Store paths for MPP&MAP */
+	struct mesh_table mesh_paths;
+	struct mesh_table mpp_paths; /* Store paths for MPP&MAP */
 	int mesh_paths_generation;
 	int mpp_paths_generation;
 };
@@ -746,6 +765,8 @@
  *	back to wireless media and to the local net stack.
  * @IEEE80211_SDATA_DISCONNECT_RESUME: Disconnect after resume.
  * @IEEE80211_SDATA_IN_DRIVER: indicates interface was added to driver
+ * @IEEE80211_SDATA_DISCONNECT_HW_RESTART: Disconnect after hardware restart
+ *  recovery
  */
 enum ieee80211_sub_if_data_flags {
 	IEEE80211_SDATA_ALLMULTI		= BIT(0),
@@ -753,6 +774,7 @@
 	IEEE80211_SDATA_DONT_BRIDGE_PACKETS	= BIT(3),
 	IEEE80211_SDATA_DISCONNECT_RESUME	= BIT(4),
 	IEEE80211_SDATA_IN_DRIVER		= BIT(5),
+	IEEE80211_SDATA_DISCONNECT_HW_RESTART	= BIT(6),
 };
 
 /**
@@ -1109,6 +1131,9 @@
  *	a scan complete for an aborted scan.
  * @SCAN_HW_CANCELLED: Set for our scan work function when the scan is being
  *	cancelled.
+ * @SCAN_BEACON_WAIT: Set whenever we're passive scanning because of radar/no-IR
+ *	and could send a probe request after receiving a beacon.
+ * @SCAN_BEACON_DONE: Beacon received, we can now send a probe request
  */
 enum {
 	SCAN_SW_SCANNING,
@@ -1117,6 +1142,8 @@
 	SCAN_COMPLETED,
 	SCAN_ABORTED,
 	SCAN_HW_CANCELLED,
+	SCAN_BEACON_WAIT,
+	SCAN_BEACON_DONE,
 };
 
 /**
@@ -1508,6 +1535,7 @@
 struct ieee802_11_elems {
 	const u8 *ie_start;
 	size_t total_len;
+	u32 crc;
 
 	/* pointers to IEs */
 	const struct ieee80211_tdls_lnkie *lnk_id;
@@ -1517,7 +1545,6 @@
 	const u8 *supp_rates;
 	const u8 *ds_params;
 	const struct ieee80211_tim_ie *tim;
-	const u8 *challenge;
 	const u8 *rsn;
 	const u8 *rsnx;
 	const u8 *erp_info;
@@ -1571,7 +1598,6 @@
 	u8 ssid_len;
 	u8 supp_rates_len;
 	u8 tim_len;
-	u8 challenge_len;
 	u8 rsn_len;
 	u8 rsnx_len;
 	u8 ext_supp_rates_len;
@@ -1590,6 +1616,14 @@
 
 	/* whether a parse error occurred while retrieving these elements */
 	bool parse_error;
+
+	/*
+	 * scratch buffer that can be used for various element parsing related
+	 * tasks, e.g., element de-fragmentation etc.
+	 */
+	size_t scratch_len;
+	u8 *scratch_pos;
+	u8 scratch[];
 };
 
 static inline struct ieee80211_local *hw_to_local(
@@ -1772,6 +1806,8 @@
 void ieee80211_configure_filter(struct ieee80211_local *local);
 u32 ieee80211_reset_erp_info(struct ieee80211_sub_if_data *sdata);
 
+void ieee80211_handle_queued_frames(struct ieee80211_local *local);
+
 u64 ieee80211_mgmt_tx_cookie(struct ieee80211_local *local);
 int ieee80211_attach_ack_skb(struct ieee80211_local *local, struct sk_buff *skb,
 			     u64 *cookie, gfp_t gfp);
@@ -2194,18 +2230,18 @@
 	ieee80211_tx_skb_tid(sdata, skb, 7);
 }
 
-u32 ieee802_11_parse_elems_crc(const u8 *start, size_t len, bool action,
-			       struct ieee802_11_elems *elems,
-			       u64 filter, u32 crc, u8 *transmitter_bssid,
-			       u8 *bss_bssid);
-static inline void ieee802_11_parse_elems(const u8 *start, size_t len,
-					  bool action,
-					  struct ieee802_11_elems *elems,
-					  u8 *transmitter_bssid,
-					  u8 *bss_bssid)
+struct ieee802_11_elems *ieee802_11_parse_elems_crc(const u8 *start, size_t len,
+						    bool action,
+						    u64 filter, u32 crc,
+						    const u8 *transmitter_bssid,
+						    const u8 *bss_bssid);
+static inline struct ieee802_11_elems *
+ieee802_11_parse_elems(const u8 *start, size_t len, bool action,
+		       const u8 *transmitter_bssid,
+		       const u8 *bss_bssid)
 {
-	ieee802_11_parse_elems_crc(start, len, action, elems, 0, 0,
-				   transmitter_bssid, bss_bssid);
+	return ieee802_11_parse_elems_crc(start, len, action, 0, 0,
+					  transmitter_bssid, bss_bssid);
 }
 
 
@@ -2359,7 +2395,7 @@
 u8 *ieee80211_ie_build_vht_oper(u8 *pos, struct ieee80211_sta_vht_cap *vht_cap,
 				const struct cfg80211_chan_def *chandef);
 u8 ieee80211_ie_len_he_cap(struct ieee80211_sub_if_data *sdata, u8 iftype);
-u8 *ieee80211_ie_build_he_cap(u8 *pos,
+u8 *ieee80211_ie_build_he_cap(u32 disable_flags, u8 *pos,
 			      const struct ieee80211_sta_he_cap *he_cap,
 			      u8 *end);
 void ieee80211_ie_build_he_6ghz_cap(struct ieee80211_sub_if_data *sdata,
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/iface.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/iface.c
@@ -369,6 +369,7 @@
 {
 	struct ieee80211_local *local = sdata->local;
 	unsigned long flags;
+	struct sk_buff_head freeq;
 	struct sk_buff *skb, *tmp;
 	u32 hw_reconf_flags = 0;
 	int i, flushed;
@@ -555,18 +556,32 @@
 		skb_queue_purge(&sdata->status_queue);
 	}
 
+	/*
+	 * Since ieee80211_free_txskb() may issue __dev_queue_xmit()
+	 * which should be called with interrupts enabled, reclamation
+	 * is done in two phases:
+	 */
+	__skb_queue_head_init(&freeq);
+
+	/* unlink from local queues... */
 	spin_lock_irqsave(&local->queue_stop_reason_lock, flags);
 	for (i = 0; i < IEEE80211_MAX_QUEUES; i++) {
 		skb_queue_walk_safe(&local->pending[i], skb, tmp) {
 			struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 			if (info->control.vif == &sdata->vif) {
 				__skb_unlink(skb, &local->pending[i]);
-				ieee80211_free_txskb(&local->hw, skb);
+				__skb_queue_tail(&freeq, skb);
 			}
 		}
 	}
 	spin_unlock_irqrestore(&local->queue_stop_reason_lock, flags);
 
+	/* ... and perform actual reclamation with interrupts enabled. */
+	skb_queue_walk_safe(&freeq, skb, tmp) {
+		__skb_unlink(skb, &freeq);
+		ieee80211_free_txskb(&local->hw, skb);
+	}
+
 	if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
 		ieee80211_txq_remove_vlan(local, sdata);
 
@@ -588,7 +603,7 @@
 	 */
 	if (local->suspended) {
 		WARN_ON(local->wowlan);
-		WARN_ON(rtnl_dereference(local->monitor_sdata));
+		WARN_ON(rcu_access_pointer(local->monitor_sdata));
 		return;
 	}
 
@@ -932,6 +947,7 @@
 		return 0;
 
 	ASSERT_RTNL();
+	lockdep_assert_wiphy(local->hw.wiphy);
 
 	if (local->monitor_sdata)
 		return 0;
@@ -999,6 +1015,7 @@
 		return;
 
 	ASSERT_RTNL();
+	lockdep_assert_wiphy(local->hw.wiphy);
 
 	mutex_lock(&local->iflist_mtx);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/key.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/key.c
@@ -843,7 +843,7 @@
 	 */
 	if (ieee80211_key_identical(sdata, old_key, key)) {
 		ieee80211_key_free_unused(key);
-		ret = 0;
+		ret = -EALREADY;
 		goto out;
 	}
 
@@ -918,6 +918,26 @@
 	mutex_unlock(&sdata->local->key_mtx);
 }
 
+static void
+ieee80211_key_iter(struct ieee80211_hw *hw,
+		   struct ieee80211_vif *vif,
+		   struct ieee80211_key *key,
+		   void (*iter)(struct ieee80211_hw *hw,
+				struct ieee80211_vif *vif,
+				struct ieee80211_sta *sta,
+				struct ieee80211_key_conf *key,
+				void *data),
+		   void *iter_data)
+{
+	/* skip keys of station in removal process */
+	if (key->sta && key->sta->removed)
+		return;
+	if (!(key->flags & KEY_FLAG_UPLOADED_TO_HARDWARE))
+		return;
+	iter(hw, vif, key->sta ? &key->sta->sta : NULL,
+	     &key->conf, iter_data);
+}
+
 void ieee80211_iter_keys(struct ieee80211_hw *hw,
 			 struct ieee80211_vif *vif,
 			 void (*iter)(struct ieee80211_hw *hw,
@@ -937,16 +957,13 @@
 	if (vif) {
 		sdata = vif_to_sdata(vif);
 		list_for_each_entry_safe(key, tmp, &sdata->key_list, list)
-			iter(hw, &sdata->vif,
-			     key->sta ? &key->sta->sta : NULL,
-			     &key->conf, iter_data);
+			ieee80211_key_iter(hw, vif, key, iter, iter_data);
 	} else {
 		list_for_each_entry(sdata, &local->interfaces, list)
 			list_for_each_entry_safe(key, tmp,
 						 &sdata->key_list, list)
-				iter(hw, &sdata->vif,
-				     key->sta ? &key->sta->sta : NULL,
-				     &key->conf, iter_data);
+				ieee80211_key_iter(hw, &sdata->vif, key,
+						   iter, iter_data);
 	}
 	mutex_unlock(&local->key_mtx);
 }
@@ -964,17 +981,8 @@
 {
 	struct ieee80211_key *key;
 
-	list_for_each_entry_rcu(key, &sdata->key_list, list) {
-		/* skip keys of station in removal process */
-		if (key->sta && key->sta->removed)
-			continue;
-		if (!(key->flags & KEY_FLAG_UPLOADED_TO_HARDWARE))
-			continue;
-
-		iter(hw, &sdata->vif,
-		     key->sta ? &key->sta->sta : NULL,
-		     &key->conf, iter_data);
-	}
+	list_for_each_entry_rcu(key, &sdata->key_list, list)
+		ieee80211_key_iter(hw, &sdata->vif, key, iter, iter_data);
 }
 
 void ieee80211_iter_keys_rcu(struct ieee80211_hw *hw,
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/led.h
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/led.h
@@ -72,19 +72,19 @@
 #endif
 
 static inline void
-ieee80211_tpt_led_trig_tx(struct ieee80211_local *local, __le16 fc, int bytes)
+ieee80211_tpt_led_trig_tx(struct ieee80211_local *local, int bytes)
 {
 #ifdef CONFIG_MAC80211_LEDS
-	if (ieee80211_is_data(fc) && atomic_read(&local->tpt_led_active))
+	if (atomic_read(&local->tpt_led_active))
 		local->tpt_led_trigger->tx_bytes += bytes;
 #endif
 }
 
 static inline void
-ieee80211_tpt_led_trig_rx(struct ieee80211_local *local, __le16 fc, int bytes)
+ieee80211_tpt_led_trig_rx(struct ieee80211_local *local, int bytes)
 {
 #ifdef CONFIG_MAC80211_LEDS
-	if (ieee80211_is_data(fc) && atomic_read(&local->tpt_led_active))
+	if (atomic_read(&local->tpt_led_active))
 		local->tpt_led_trigger->rx_bytes += bytes;
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/main.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/main.c
@@ -144,6 +144,8 @@
 	}
 
 	power = ieee80211_chandef_max_power(&chandef);
+	if (local->user_power_level != IEEE80211_UNSET_POWER_LEVEL)
+		power = min(local->user_power_level, power);
 
 	rcu_read_lock();
 	list_for_each_entry_rcu(sdata, &local->interfaces, list) {
@@ -220,9 +222,9 @@
 	       BSS_CHANGED_ERP_SLOT;
 }
 
-static void ieee80211_tasklet_handler(struct tasklet_struct *t)
+/* context: requires softirqs disabled */
+void ieee80211_handle_queued_frames(struct ieee80211_local *local)
 {
-	struct ieee80211_local *local = from_tasklet(local, t, tasklet);
 	struct sk_buff *skb;
 
 	while ((skb = skb_dequeue(&local->skb_queue)) ||
@@ -247,6 +249,13 @@
 	}
 }
 
+static void ieee80211_tasklet_handler(struct tasklet_struct *t)
+{
+	struct ieee80211_local *local = from_tasklet(local, t, tasklet);
+
+	ieee80211_handle_queued_frames(local);
+}
+
 static void ieee80211_restart_work(struct work_struct *work)
 {
 	struct ieee80211_local *local =
@@ -1131,17 +1140,14 @@
 		local->scan_ies_len +=
 			2 + sizeof(struct ieee80211_vht_cap);
 
-	/* HE cap element is variable in size - set len to allow max size */
 	/*
-	 * TODO: 1 is added at the end of the calculation to accommodate for
-	 *	the temporary placing of the HE capabilities IE under EXT.
-	 *	Remove it once it is placed in the final place.
-	 */
-	if (supp_he)
+	 * HE cap element is variable in size - set len to allow max size */
+	if (supp_he) {
 		local->scan_ies_len +=
-			2 + sizeof(struct ieee80211_he_cap_elem) +
+			3 + sizeof(struct ieee80211_he_cap_elem) +
 			sizeof(struct ieee80211_he_mcs_nss_supp) +
-			IEEE80211_HE_PPE_THRES_MAX_LEN + 1;
+			IEEE80211_HE_PPE_THRES_MAX_LEN;
+	}
 
 	if (!local->ops->hw_scan) {
 		/* For hw_scan, driver needs to set these up. */
@@ -1360,8 +1366,10 @@
 	ieee80211_led_exit(local);
 	destroy_workqueue(local->workqueue);
  fail_workqueue:
-	if (local->wiphy_ciphers_allocated)
+	if (local->wiphy_ciphers_allocated) {
 		kfree(local->hw.wiphy->cipher_suites);
+		local->wiphy_ciphers_allocated = false;
+	}
 	kfree(local->int_scan_req);
 	return result;
 }
@@ -1429,8 +1437,10 @@
 	mutex_destroy(&local->iflist_mtx);
 	mutex_destroy(&local->mtx);
 
-	if (local->wiphy_ciphers_allocated)
+	if (local->wiphy_ciphers_allocated) {
 		kfree(local->hw.wiphy->cipher_suites);
+		local->wiphy_ciphers_allocated = false;
+	}
 
 	idr_for_each(&local->ack_status_frames,
 		     ieee80211_free_ack_frame, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mesh.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mesh.c
@@ -580,7 +580,7 @@
 		return -ENOMEM;
 
 	pos = skb_put(skb, ie_len);
-	ieee80211_ie_build_he_cap(pos, he_cap, pos + ie_len);
+	ieee80211_ie_build_he_cap(0, pos, he_cap, pos + ie_len);
 
 	return 0;
 }
@@ -1247,7 +1247,7 @@
 	struct sk_buff *presp;
 	struct beacon_data *bcn;
 	struct ieee80211_mgmt *hdr;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	size_t baselen;
 	u8 *pos;
 
@@ -1256,22 +1256,24 @@
 	if (baselen > len)
 		return;
 
-	ieee802_11_parse_elems(pos, len - baselen, false, &elems, mgmt->bssid,
-			       NULL);
-
-	if (!elems.mesh_id)
+	elems = ieee802_11_parse_elems(pos, len - baselen, false, mgmt->bssid,
+				       NULL);
+	if (!elems)
 		return;
 
+	if (!elems->mesh_id)
+		goto free;
+
 	/* 802.11-2012 10.1.4.3.2 */
 	if ((!ether_addr_equal(mgmt->da, sdata->vif.addr) &&
 	     !is_broadcast_ether_addr(mgmt->da)) ||
-	    elems.ssid_len != 0)
-		return;
+	    elems->ssid_len != 0)
+		goto free;
 
-	if (elems.mesh_id_len != 0 &&
-	    (elems.mesh_id_len != ifmsh->mesh_id_len ||
-	     memcmp(elems.mesh_id, ifmsh->mesh_id, ifmsh->mesh_id_len)))
-		return;
+	if (elems->mesh_id_len != 0 &&
+	    (elems->mesh_id_len != ifmsh->mesh_id_len ||
+	     memcmp(elems->mesh_id, ifmsh->mesh_id, ifmsh->mesh_id_len)))
+		goto free;
 
 	rcu_read_lock();
 	bcn = rcu_dereference(ifmsh->beacon);
@@ -1295,6 +1297,8 @@
 	ieee80211_tx_skb(sdata, presp);
 out:
 	rcu_read_unlock();
+free:
+	kfree(elems);
 }
 
 static void ieee80211_mesh_rx_bcn_presp(struct ieee80211_sub_if_data *sdata,
@@ -1305,7 +1309,7 @@
 {
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	struct ieee80211_channel *channel;
 	size_t baselen;
 	int freq;
@@ -1320,42 +1324,47 @@
 	if (baselen > len)
 		return;
 
-	ieee802_11_parse_elems(mgmt->u.probe_resp.variable, len - baselen,
-			       false, &elems, mgmt->bssid, NULL);
+	elems = ieee802_11_parse_elems(mgmt->u.probe_resp.variable,
+				       len - baselen,
+				       false, mgmt->bssid, NULL);
+	if (!elems)
+		return;
 
 	/* ignore non-mesh or secure / unsecure mismatch */
-	if ((!elems.mesh_id || !elems.mesh_config) ||
-	    (elems.rsn && sdata->u.mesh.security == IEEE80211_MESH_SEC_NONE) ||
-	    (!elems.rsn && sdata->u.mesh.security != IEEE80211_MESH_SEC_NONE))
-		return;
+	if ((!elems->mesh_id || !elems->mesh_config) ||
+	    (elems->rsn && sdata->u.mesh.security == IEEE80211_MESH_SEC_NONE) ||
+	    (!elems->rsn && sdata->u.mesh.security != IEEE80211_MESH_SEC_NONE))
+		goto free;
 
-	if (elems.ds_params)
-		freq = ieee80211_channel_to_frequency(elems.ds_params[0], band);
+	if (elems->ds_params)
+		freq = ieee80211_channel_to_frequency(elems->ds_params[0], band);
 	else
 		freq = rx_status->freq;
 
 	channel = ieee80211_get_channel(local->hw.wiphy, freq);
 
 	if (!channel || channel->flags & IEEE80211_CHAN_DISABLED)
-		return;
+		goto free;
 
-	if (mesh_matches_local(sdata, &elems)) {
+	if (mesh_matches_local(sdata, elems)) {
 		mpl_dbg(sdata, "rssi_threshold=%d,rx_status->signal=%d\n",
 			sdata->u.mesh.mshcfg.rssi_threshold, rx_status->signal);
 		if (!sdata->u.mesh.user_mpm ||
 		    sdata->u.mesh.mshcfg.rssi_threshold == 0 ||
 		    sdata->u.mesh.mshcfg.rssi_threshold < rx_status->signal)
-			mesh_neighbour_update(sdata, mgmt->sa, &elems,
+			mesh_neighbour_update(sdata, mgmt->sa, elems,
 					      rx_status);
 
 		if (ifmsh->csa_role != IEEE80211_MESH_CSA_ROLE_INIT &&
 		    !sdata->vif.csa_active)
-			ieee80211_mesh_process_chnswitch(sdata, &elems, true);
+			ieee80211_mesh_process_chnswitch(sdata, elems, true);
 	}
 
 	if (ifmsh->sync_ops)
-		ifmsh->sync_ops->rx_bcn_presp(sdata,
-			stype, mgmt, &elems, rx_status);
+		ifmsh->sync_ops->rx_bcn_presp(sdata, stype, mgmt, len,
+					      elems->mesh_config, rx_status);
+free:
+	kfree(elems);
 }
 
 int ieee80211_mesh_finish_csa(struct ieee80211_sub_if_data *sdata)
@@ -1447,7 +1456,7 @@
 			      struct ieee80211_mgmt *mgmt, size_t len)
 {
 	struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	u16 pre_value;
 	bool fwd_csa = true;
 	size_t baselen;
@@ -1460,33 +1469,37 @@
 	pos = mgmt->u.action.u.chan_switch.variable;
 	baselen = offsetof(struct ieee80211_mgmt,
 			   u.action.u.chan_switch.variable);
-	ieee802_11_parse_elems(pos, len - baselen, true, &elems,
-			       mgmt->bssid, NULL);
-
-	if (!mesh_matches_local(sdata, &elems))
+	elems = ieee802_11_parse_elems(pos, len - baselen, true,
+				       mgmt->bssid, NULL);
+	if (!elems)
 		return;
 
-	ifmsh->chsw_ttl = elems.mesh_chansw_params_ie->mesh_ttl;
+	if (!mesh_matches_local(sdata, elems))
+		goto free;
+
+	ifmsh->chsw_ttl = elems->mesh_chansw_params_ie->mesh_ttl;
 	if (!--ifmsh->chsw_ttl)
 		fwd_csa = false;
 
-	pre_value = le16_to_cpu(elems.mesh_chansw_params_ie->mesh_pre_value);
+	pre_value = le16_to_cpu(elems->mesh_chansw_params_ie->mesh_pre_value);
 	if (ifmsh->pre_value >= pre_value)
-		return;
+		goto free;
 
 	ifmsh->pre_value = pre_value;
 
 	if (!sdata->vif.csa_active &&
-	    !ieee80211_mesh_process_chnswitch(sdata, &elems, false)) {
+	    !ieee80211_mesh_process_chnswitch(sdata, elems, false)) {
 		mcsa_dbg(sdata, "Failed to process CSA action frame");
-		return;
+		goto free;
 	}
 
 	/* forward or re-broadcast the CSA frame */
 	if (fwd_csa) {
-		if (mesh_fwd_csa_frame(sdata, mgmt, len, &elems) < 0)
+		if (mesh_fwd_csa_frame(sdata, mgmt, len, elems) < 0)
 			mcsa_dbg(sdata, "Failed to forward the CSA frame");
 	}
+free:
+	kfree(elems);
 }
 
 static void ieee80211_mesh_rx_mgmt_action(struct ieee80211_sub_if_data *sdata,
@@ -1615,6 +1628,7 @@
 	ifmsh->last_preq = jiffies;
 	ifmsh->next_perr = jiffies;
 	ifmsh->csa_role = IEEE80211_MESH_CSA_ROLE_NONE;
+	ifmsh->nonpeer_pm = NL80211_MESH_POWER_ACTIVE;
 	/* Allocate all mesh structures when creating the first mesh interface. */
 	if (!mesh_allocated)
 		ieee80211s_init();
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mesh.h
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mesh.h
@@ -127,26 +127,6 @@
 	u32 path_change_count;
 };
 
-/**
- * struct mesh_table
- *
- * @known_gates: list of known mesh gates and their mpaths by the station. The
- * gate's mpath may or may not be resolved and active.
- * @gates_lock: protects updates to known_gates
- * @rhead: the rhashtable containing struct mesh_paths, keyed by dest addr
- * @walk_head: linked list containing all mesh_path objects
- * @walk_lock: lock protecting walk_head
- * @entries: number of entries in the table
- */
-struct mesh_table {
-	struct hlist_head known_gates;
-	spinlock_t gates_lock;
-	struct rhashtable rhead;
-	struct hlist_head walk_head;
-	spinlock_t walk_lock;
-	atomic_t entries;		/* Up to MAX_MESH_NEIGHBOURS */
-};
-
 /* Recent multicast cache */
 /* RMC_BUCKETS must be a power of 2, maximum 256 */
 #define RMC_BUCKETS		256
@@ -308,7 +288,7 @@
 void mesh_path_assign_nexthop(struct mesh_path *mpath, struct sta_info *sta);
 void mesh_path_flush_pending(struct mesh_path *mpath);
 void mesh_path_tx_pending(struct mesh_path *mpath);
-int mesh_pathtbl_init(struct ieee80211_sub_if_data *sdata);
+void mesh_pathtbl_init(struct ieee80211_sub_if_data *sdata);
 void mesh_pathtbl_unregister(struct ieee80211_sub_if_data *sdata);
 int mesh_path_del(struct ieee80211_sub_if_data *sdata, const u8 *addr);
 void mesh_path_timer(struct timer_list *t);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mesh_hwmp.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mesh_hwmp.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2008, 2009 open80211s Ltd.
- * Copyright (C) 2019 Intel Corporation
+ * Copyright (C) 2019, 2021 Intel Corporation
  * Author:     Luis Carlos Cobo <luisca@cozybit.com>
  */
 
@@ -908,7 +908,7 @@
 void mesh_rx_path_sel_frame(struct ieee80211_sub_if_data *sdata,
 			    struct ieee80211_mgmt *mgmt, size_t len)
 {
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	size_t baselen;
 	u32 path_metric;
 	struct sta_info *sta;
@@ -926,37 +926,41 @@
 	rcu_read_unlock();
 
 	baselen = (u8 *) mgmt->u.action.u.mesh_action.variable - (u8 *) mgmt;
-	ieee802_11_parse_elems(mgmt->u.action.u.mesh_action.variable,
-			       len - baselen, false, &elems, mgmt->bssid, NULL);
+	elems = ieee802_11_parse_elems(mgmt->u.action.u.mesh_action.variable,
+				       len - baselen, false, mgmt->bssid, NULL);
+	if (!elems)
+		return;
 
-	if (elems.preq) {
-		if (elems.preq_len != 37)
+	if (elems->preq) {
+		if (elems->preq_len != 37)
 			/* Right now we support just 1 destination and no AE */
-			return;
-		path_metric = hwmp_route_info_get(sdata, mgmt, elems.preq,
+			goto free;
+		path_metric = hwmp_route_info_get(sdata, mgmt, elems->preq,
 						  MPATH_PREQ);
 		if (path_metric)
-			hwmp_preq_frame_process(sdata, mgmt, elems.preq,
+			hwmp_preq_frame_process(sdata, mgmt, elems->preq,
 						path_metric);
 	}
-	if (elems.prep) {
-		if (elems.prep_len != 31)
+	if (elems->prep) {
+		if (elems->prep_len != 31)
 			/* Right now we support no AE */
-			return;
-		path_metric = hwmp_route_info_get(sdata, mgmt, elems.prep,
+			goto free;
+		path_metric = hwmp_route_info_get(sdata, mgmt, elems->prep,
 						  MPATH_PREP);
 		if (path_metric)
-			hwmp_prep_frame_process(sdata, mgmt, elems.prep,
+			hwmp_prep_frame_process(sdata, mgmt, elems->prep,
 						path_metric);
 	}
-	if (elems.perr) {
-		if (elems.perr_len != 15)
+	if (elems->perr) {
+		if (elems->perr_len != 15)
 			/* Right now we support only one destination per PERR */
-			return;
-		hwmp_perr_frame_process(sdata, mgmt, elems.perr);
+			goto free;
+		hwmp_perr_frame_process(sdata, mgmt, elems->perr);
 	}
-	if (elems.rann)
-		hwmp_rann_frame_process(sdata, mgmt, elems.rann);
+	if (elems->rann)
+		hwmp_rann_frame_process(sdata, mgmt, elems->rann);
+free:
+	kfree(elems);
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mesh_pathtbl.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mesh_pathtbl.c
@@ -47,32 +47,24 @@
 	mesh_path_free_rcu(tbl, mpath);
 }
 
-static struct mesh_table *mesh_table_alloc(void)
+static void mesh_table_init(struct mesh_table *tbl)
 {
-	struct mesh_table *newtbl;
-
-	newtbl = kmalloc(sizeof(struct mesh_table), GFP_ATOMIC);
-	if (!newtbl)
-		return NULL;
-
-	INIT_HLIST_HEAD(&newtbl->known_gates);
-	INIT_HLIST_HEAD(&newtbl->walk_head);
-	atomic_set(&newtbl->entries,  0);
-	spin_lock_init(&newtbl->gates_lock);
-	spin_lock_init(&newtbl->walk_lock);
-	if (rhashtable_init(&newtbl->rhead, &mesh_rht_params)) {
-		kfree(newtbl);
-		return NULL;
-	}
-
-	return newtbl;
+	INIT_HLIST_HEAD(&tbl->known_gates);
+	INIT_HLIST_HEAD(&tbl->walk_head);
+	atomic_set(&tbl->entries,  0);
+	spin_lock_init(&tbl->gates_lock);
+	spin_lock_init(&tbl->walk_lock);
+
+	/* rhashtable_init() may fail only in case of wrong
+	 * mesh_rht_params
+	 */
+	WARN_ON(rhashtable_init(&tbl->rhead, &mesh_rht_params));
 }
 
 static void mesh_table_free(struct mesh_table *tbl)
 {
 	rhashtable_free_and_destroy(&tbl->rhead,
 				    mesh_path_rht_free, tbl);
-	kfree(tbl);
 }
 
 /**
@@ -238,13 +230,13 @@
 struct mesh_path *
 mesh_path_lookup(struct ieee80211_sub_if_data *sdata, const u8 *dst)
 {
-	return mpath_lookup(sdata->u.mesh.mesh_paths, dst, sdata);
+	return mpath_lookup(&sdata->u.mesh.mesh_paths, dst, sdata);
 }
 
 struct mesh_path *
 mpp_path_lookup(struct ieee80211_sub_if_data *sdata, const u8 *dst)
 {
-	return mpath_lookup(sdata->u.mesh.mpp_paths, dst, sdata);
+	return mpath_lookup(&sdata->u.mesh.mpp_paths, dst, sdata);
 }
 
 static struct mesh_path *
@@ -281,7 +273,7 @@
 struct mesh_path *
 mesh_path_lookup_by_idx(struct ieee80211_sub_if_data *sdata, int idx)
 {
-	return __mesh_path_lookup_by_idx(sdata->u.mesh.mesh_paths, idx);
+	return __mesh_path_lookup_by_idx(&sdata->u.mesh.mesh_paths, idx);
 }
 
 /**
@@ -296,7 +288,7 @@
 struct mesh_path *
 mpp_path_lookup_by_idx(struct ieee80211_sub_if_data *sdata, int idx)
 {
-	return __mesh_path_lookup_by_idx(sdata->u.mesh.mpp_paths, idx);
+	return __mesh_path_lookup_by_idx(&sdata->u.mesh.mpp_paths, idx);
 }
 
 /**
@@ -309,7 +301,7 @@
 	int err;
 
 	rcu_read_lock();
-	tbl = mpath->sdata->u.mesh.mesh_paths;
+	tbl = &mpath->sdata->u.mesh.mesh_paths;
 
 	spin_lock_bh(&mpath->state_lock);
 	if (mpath->is_gate) {
@@ -418,7 +410,7 @@
 	if (!new_mpath)
 		return ERR_PTR(-ENOMEM);
 
-	tbl = sdata->u.mesh.mesh_paths;
+	tbl = &sdata->u.mesh.mesh_paths;
 	spin_lock_bh(&tbl->walk_lock);
 	mpath = rhashtable_lookup_get_insert_fast(&tbl->rhead,
 						  &new_mpath->rhash,
@@ -460,7 +452,7 @@
 		return -ENOMEM;
 
 	memcpy(new_mpath->mpp, mpp, ETH_ALEN);
-	tbl = sdata->u.mesh.mpp_paths;
+	tbl = &sdata->u.mesh.mpp_paths;
 
 	spin_lock_bh(&tbl->walk_lock);
 	ret = rhashtable_lookup_insert_fast(&tbl->rhead,
@@ -489,7 +481,7 @@
 void mesh_plink_broken(struct sta_info *sta)
 {
 	struct ieee80211_sub_if_data *sdata = sta->sdata;
-	struct mesh_table *tbl = sdata->u.mesh.mesh_paths;
+	struct mesh_table *tbl = &sdata->u.mesh.mesh_paths;
 	static const u8 bcast[ETH_ALEN] = {0xff, 0xff, 0xff, 0xff, 0xff, 0xff};
 	struct mesh_path *mpath;
 
@@ -548,7 +540,7 @@
 void mesh_path_flush_by_nexthop(struct sta_info *sta)
 {
 	struct ieee80211_sub_if_data *sdata = sta->sdata;
-	struct mesh_table *tbl = sdata->u.mesh.mesh_paths;
+	struct mesh_table *tbl = &sdata->u.mesh.mesh_paths;
 	struct mesh_path *mpath;
 	struct hlist_node *n;
 
@@ -563,7 +555,7 @@
 static void mpp_flush_by_proxy(struct ieee80211_sub_if_data *sdata,
 			       const u8 *proxy)
 {
-	struct mesh_table *tbl = sdata->u.mesh.mpp_paths;
+	struct mesh_table *tbl = &sdata->u.mesh.mpp_paths;
 	struct mesh_path *mpath;
 	struct hlist_node *n;
 
@@ -597,8 +589,8 @@
  */
 void mesh_path_flush_by_iface(struct ieee80211_sub_if_data *sdata)
 {
-	table_flush_by_iface(sdata->u.mesh.mesh_paths);
-	table_flush_by_iface(sdata->u.mesh.mpp_paths);
+	table_flush_by_iface(&sdata->u.mesh.mesh_paths);
+	table_flush_by_iface(&sdata->u.mesh.mpp_paths);
 }
 
 /**
@@ -644,7 +636,7 @@
 	/* flush relevant mpp entries first */
 	mpp_flush_by_proxy(sdata, addr);
 
-	err = table_path_del(sdata->u.mesh.mesh_paths, sdata, addr);
+	err = table_path_del(&sdata->u.mesh.mesh_paths, sdata, addr);
 	sdata->u.mesh.mesh_paths_generation++;
 	return err;
 }
@@ -682,7 +674,7 @@
 	struct mesh_path *gate;
 	bool copy = false;
 
-	tbl = sdata->u.mesh.mesh_paths;
+	tbl = &sdata->u.mesh.mesh_paths;
 
 	rcu_read_lock();
 	hlist_for_each_entry_rcu(gate, &tbl->known_gates, gate_list) {
@@ -718,7 +710,7 @@
 void mesh_path_discard_frame(struct ieee80211_sub_if_data *sdata,
 			     struct sk_buff *skb)
 {
-	kfree_skb(skb);
+	ieee80211_free_txskb(&sdata->local->hw, skb);
 	sdata->u.mesh.mshstats.dropped_frames_no_route++;
 }
 
@@ -731,10 +723,23 @@
  */
 void mesh_path_flush_pending(struct mesh_path *mpath)
 {
+	struct ieee80211_sub_if_data *sdata = mpath->sdata;
+	struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
+	struct mesh_preq_queue *preq, *tmp;
 	struct sk_buff *skb;
 
 	while ((skb = skb_dequeue(&mpath->frame_queue)) != NULL)
 		mesh_path_discard_frame(mpath->sdata, skb);
+
+	spin_lock_bh(&ifmsh->mesh_preq_queue_lock);
+	list_for_each_entry_safe(preq, tmp, &ifmsh->preq_queue.list, list) {
+		if (ether_addr_equal(mpath->dst, preq->dst)) {
+			list_del(&preq->list);
+			kfree(preq);
+			--ifmsh->preq_queue_len;
+		}
+	}
+	spin_unlock_bh(&ifmsh->mesh_preq_queue_lock);
 }
 
 /**
@@ -762,29 +767,10 @@
 	mesh_path_tx_pending(mpath);
 }
 
-int mesh_pathtbl_init(struct ieee80211_sub_if_data *sdata)
+void mesh_pathtbl_init(struct ieee80211_sub_if_data *sdata)
 {
-	struct mesh_table *tbl_path, *tbl_mpp;
-	int ret;
-
-	tbl_path = mesh_table_alloc();
-	if (!tbl_path)
-		return -ENOMEM;
-
-	tbl_mpp = mesh_table_alloc();
-	if (!tbl_mpp) {
-		ret = -ENOMEM;
-		goto free_path;
-	}
-
-	sdata->u.mesh.mesh_paths = tbl_path;
-	sdata->u.mesh.mpp_paths = tbl_mpp;
-
-	return 0;
-
-free_path:
-	mesh_table_free(tbl_path);
-	return ret;
+	mesh_table_init(&sdata->u.mesh.mesh_paths);
+	mesh_table_init(&sdata->u.mesh.mpp_paths);
 }
 
 static
@@ -806,12 +792,12 @@
 
 void mesh_path_expire(struct ieee80211_sub_if_data *sdata)
 {
-	mesh_path_tbl_expire(sdata, sdata->u.mesh.mesh_paths);
-	mesh_path_tbl_expire(sdata, sdata->u.mesh.mpp_paths);
+	mesh_path_tbl_expire(sdata, &sdata->u.mesh.mesh_paths);
+	mesh_path_tbl_expire(sdata, &sdata->u.mesh.mpp_paths);
 }
 
 void mesh_pathtbl_unregister(struct ieee80211_sub_if_data *sdata)
 {
-	mesh_table_free(sdata->u.mesh.mesh_paths);
-	mesh_table_free(sdata->u.mesh.mpp_paths);
+	mesh_table_free(&sdata->u.mesh.mesh_paths);
+	mesh_table_free(&sdata->u.mesh.mpp_paths);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mesh_plink.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mesh_plink.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2008, 2009 open80211s Ltd.
- * Copyright (C) 2019 Intel Corporation
+ * Copyright (C) 2019, 2021 Intel Corporation
  * Author:     Luis Carlos Cobo <luisca@cozybit.com>
  */
 #include <linux/gfp.h>
@@ -1050,8 +1050,8 @@
 	case WLAN_SP_MESH_PEERING_OPEN:
 		if (!matches_local)
 			event = OPN_RJCT;
-		if (!mesh_plink_free_count(sdata) ||
-		    (sta->mesh->plid && sta->mesh->plid != plid))
+		else if (!mesh_plink_free_count(sdata) ||
+			 (sta->mesh->plid && sta->mesh->plid != plid))
 			event = OPN_IGNR;
 		else
 			event = OPN_ACPT;
@@ -1059,9 +1059,9 @@
 	case WLAN_SP_MESH_PEERING_CONFIRM:
 		if (!matches_local)
 			event = CNF_RJCT;
-		if (!mesh_plink_free_count(sdata) ||
-		    sta->mesh->llid != llid ||
-		    (sta->mesh->plid && sta->mesh->plid != plid))
+		else if (!mesh_plink_free_count(sdata) ||
+			 sta->mesh->llid != llid ||
+			 (sta->mesh->plid && sta->mesh->plid != plid))
 			event = CNF_IGNR;
 		else
 			event = CNF_ACPT;
@@ -1200,7 +1200,7 @@
 			 struct ieee80211_mgmt *mgmt, size_t len,
 			 struct ieee80211_rx_status *rx_status)
 {
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	size_t baselen;
 	u8 *baseaddr;
 
@@ -1228,7 +1228,8 @@
 		if (baselen > len)
 			return;
 	}
-	ieee802_11_parse_elems(baseaddr, len - baselen, true, &elems,
-			       mgmt->bssid, NULL);
-	mesh_process_plink_frame(sdata, mgmt, &elems, rx_status);
+	elems = ieee802_11_parse_elems(baseaddr, len - baselen, true,
+				       mgmt->bssid, NULL);
+	mesh_process_plink_frame(sdata, mgmt, elems, rx_status);
+	kfree(elems);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mesh_sync.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mesh_sync.c
@@ -3,6 +3,7 @@
  * Copyright 2011-2012, Pavel Zubarev <pavel.zubarev@gmail.com>
  * Copyright 2011-2012, Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
  * Copyright 2011-2012, cozybit Inc.
+ * Copyright (C) 2021 Intel Corporation
  */
 
 #include "ieee80211_i.h"
@@ -35,12 +36,12 @@
 /**
  * mesh_peer_tbtt_adjusting - check if an mp is currently adjusting its TBTT
  *
- * @ie: information elements of a management frame from the mesh peer
+ * @cfg: mesh config element from the mesh peer (or %NULL)
  */
-static bool mesh_peer_tbtt_adjusting(struct ieee802_11_elems *ie)
+static bool mesh_peer_tbtt_adjusting(const struct ieee80211_meshconf_ie *cfg)
 {
-	return (ie->mesh_config->meshconf_cap &
-			IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING) != 0;
+	return cfg &&
+	       (cfg->meshconf_cap & IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING);
 }
 
 void mesh_sync_adjust_tsf(struct ieee80211_sub_if_data *sdata)
@@ -76,11 +77,11 @@
 	}
 }
 
-static void mesh_sync_offset_rx_bcn_presp(struct ieee80211_sub_if_data *sdata,
-				   u16 stype,
-				   struct ieee80211_mgmt *mgmt,
-				   struct ieee802_11_elems *elems,
-				   struct ieee80211_rx_status *rx_status)
+static void
+mesh_sync_offset_rx_bcn_presp(struct ieee80211_sub_if_data *sdata, u16 stype,
+			      struct ieee80211_mgmt *mgmt, unsigned int len,
+			      const struct ieee80211_meshconf_ie *mesh_cfg,
+			      struct ieee80211_rx_status *rx_status)
 {
 	struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
 	struct ieee80211_local *local = sdata->local;
@@ -101,10 +102,7 @@
 	 */
 	if (ieee80211_have_rx_timestamp(rx_status))
 		t_r = ieee80211_calculate_rx_timestamp(local, rx_status,
-						       24 + 12 +
-						       elems->total_len +
-						       FCS_LEN,
-						       24);
+						       len + FCS_LEN, 24);
 	else
 		t_r = drv_get_tsf(local, sdata);
 
@@ -119,7 +117,7 @@
 	 * dot11MeshNbrOffsetMaxNeighbor non-peer non-MBSS neighbors
 	 */
 
-	if (elems->mesh_config && mesh_peer_tbtt_adjusting(elems)) {
+	if (mesh_peer_tbtt_adjusting(mesh_cfg)) {
 		msync_dbg(sdata, "STA %pM : is adjusting TBTT\n",
 			  sta->sta.addr);
 		goto no_sync;
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/mlme.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/mlme.c
@@ -37,6 +37,7 @@
 #define IEEE80211_AUTH_TIMEOUT_SAE	(HZ * 2)
 #define IEEE80211_AUTH_MAX_TRIES	3
 #define IEEE80211_AUTH_WAIT_ASSOC	(HZ * 5)
+#define IEEE80211_AUTH_WAIT_SAE_RETRY	(HZ * 2)
 #define IEEE80211_ASSOC_TIMEOUT		(HZ / 5)
 #define IEEE80211_ASSOC_TIMEOUT_LONG	(HZ / 2)
 #define IEEE80211_ASSOC_TIMEOUT_SHORT	(HZ / 10)
@@ -629,7 +630,7 @@
 				struct sk_buff *skb,
 				struct ieee80211_supported_band *sband)
 {
-	u8 *pos;
+	u8 *pos, *pre_he_pos;
 	const struct ieee80211_sta_he_cap *he_cap = NULL;
 	struct ieee80211_chanctx_conf *chanctx_conf;
 	u8 he_cap_size;
@@ -646,25 +647,26 @@
 
 	he_cap = ieee80211_get_he_iftype_cap(sband,
 					     ieee80211_vif_type_p2p(&sdata->vif));
-	if (!he_cap || !reg_cap)
+	if (!he_cap || !chanctx_conf || !reg_cap)
 		return;
 
-	/*
-	 * TODO: the 1 added is because this temporarily is under the EXTENSION
-	 * IE. Get rid of it when it moves.
-	 */
+	/* get a max size estimate */
 	he_cap_size =
 		2 + 1 + sizeof(he_cap->he_cap_elem) +
 		ieee80211_he_mcs_nss_size(&he_cap->he_cap_elem) +
 		ieee80211_he_ppe_size(he_cap->ppe_thres[0],
 				      he_cap->he_cap_elem.phy_cap_info);
 	pos = skb_put(skb, he_cap_size);
-	ieee80211_ie_build_he_cap(pos, he_cap, pos + he_cap_size);
+	pre_he_pos = pos;
+	pos = ieee80211_ie_build_he_cap(sdata->u.mgd.flags,
+					pos, he_cap, pos + he_cap_size);
+	/* trim excess if any */
+	skb_trim(skb, skb->len - (pre_he_pos + he_cap_size - pos));
 
 	ieee80211_ie_build_he_6ghz_cap(sdata, skb);
 }
 
-static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
+static int ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
 {
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
@@ -684,6 +686,7 @@
 	enum nl80211_iftype iftype = ieee80211_vif_type_p2p(&sdata->vif);
 	const struct ieee80211_sband_iftype_data *iftd;
 	struct ieee80211_prep_tx_info info = {};
+	int ret;
 
 	/* we know it's writable, cast away the const */
 	if (assoc_data->ie_len)
@@ -697,7 +700,7 @@
 	chanctx_conf = rcu_dereference(sdata->vif.chanctx_conf);
 	if (WARN_ON(!chanctx_conf)) {
 		rcu_read_unlock();
-		return;
+		return -EINVAL;
 	}
 	chan = chanctx_conf->def.chan;
 	rcu_read_unlock();
@@ -748,7 +751,7 @@
 			(iftd ? iftd->vendor_elems.len : 0),
 			GFP_KERNEL);
 	if (!skb)
-		return;
+		return -ENOMEM;
 
 	skb_reserve(skb, local->hw.extra_tx_headroom);
 
@@ -1029,15 +1032,22 @@
 		skb_put_data(skb, assoc_data->ie + offset, noffset - offset);
 	}
 
-	if (assoc_data->fils_kek_len &&
-	    fils_encrypt_assoc_req(skb, assoc_data) < 0) {
-		dev_kfree_skb(skb);
-		return;
+	if (assoc_data->fils_kek_len) {
+		ret = fils_encrypt_assoc_req(skb, assoc_data);
+		if (ret < 0) {
+			dev_kfree_skb(skb);
+			return ret;
+		}
 	}
 
 	pos = skb_tail_pointer(skb);
 	kfree(ifmgd->assoc_req_ies);
 	ifmgd->assoc_req_ies = kmemdup(ie_start, pos - ie_start, GFP_ATOMIC);
+	if (!ifmgd->assoc_req_ies) {
+		dev_kfree_skb(skb);
+		return -ENOMEM;
+	}
+
 	ifmgd->assoc_req_ies_len = pos - ie_start;
 
 	drv_mgd_prepare_tx(local, sdata, &info);
@@ -1047,6 +1057,8 @@
 		IEEE80211_SKB_CB(skb)->flags |= IEEE80211_TX_CTL_REQ_TX_STATUS |
 						IEEE80211_TX_INTFL_MLME_CONN_TX;
 	ieee80211_tx_skb(sdata, skb);
+
+	return 0;
 }
 
 void ieee80211_send_pspoll(struct ieee80211_local *local,
@@ -2446,11 +2458,18 @@
 					   u16 tx_time)
 {
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
-	u16 tid = ieee80211_get_tid(hdr);
-	int ac = ieee80211_ac_from_tid(tid);
-	struct ieee80211_sta_tx_tspec *tx_tspec = &ifmgd->tx_tspec[ac];
+	u16 tid;
+	int ac;
+	struct ieee80211_sta_tx_tspec *tx_tspec;
 	unsigned long now = jiffies;
 
+	if (!ieee80211_is_data_qos(hdr->frame_control))
+		return;
+
+	tid = ieee80211_get_tid(hdr);
+	ac = ieee80211_ac_from_tid(tid);
+	tx_tspec = &ifmgd->tx_tspec[ac];
+
 	if (likely(!tx_tspec->admitted_time))
 		return;
 
@@ -2870,17 +2889,17 @@
 {
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_mgd_auth_data *auth_data = sdata->u.mgd.auth_data;
+	const struct element *challenge;
 	u8 *pos;
-	struct ieee802_11_elems elems;
 	u32 tx_flags = 0;
 	struct ieee80211_prep_tx_info info = {
 		.subtype = IEEE80211_STYPE_AUTH,
 	};
 
 	pos = mgmt->u.auth.variable;
-	ieee802_11_parse_elems(pos, len - (pos - (u8 *)mgmt), false, &elems,
-			       mgmt->bssid, auth_data->bss->bssid);
-	if (!elems.challenge)
+	challenge = cfg80211_find_elem(WLAN_EID_CHALLENGE, pos,
+				       len - (pos - (u8 *)mgmt));
+	if (!challenge)
 		return;
 	auth_data->expected_transaction = 4;
 	drv_mgd_prepare_tx(sdata->local, sdata, &info);
@@ -2888,7 +2907,8 @@
 		tx_flags = IEEE80211_TX_CTL_REQ_TX_STATUS |
 			   IEEE80211_TX_INTFL_MLME_CONN_TX;
 	ieee80211_send_auth(sdata, 3, auth_data->algorithm, 0,
-			    elems.challenge - 2, elems.challenge_len + 2,
+			    (void *)challenge,
+			    challenge->datalen + sizeof(*challenge),
 			    auth_data->bss->bssid, auth_data->bss->bssid,
 			    auth_data->key, auth_data->key_len,
 			    auth_data->key_idx, tx_flags);
@@ -2977,8 +2997,15 @@
 		    (status_code == WLAN_STATUS_ANTI_CLOG_REQUIRED ||
 		     (auth_transaction == 1 &&
 		      (status_code == WLAN_STATUS_SAE_HASH_TO_ELEMENT ||
-		       status_code == WLAN_STATUS_SAE_PK))))
+		       status_code == WLAN_STATUS_SAE_PK)))) {
+			/* waiting for userspace now */
+			ifmgd->auth_data->waiting = true;
+			ifmgd->auth_data->timeout =
+				jiffies + IEEE80211_AUTH_WAIT_SAE_RETRY;
+			ifmgd->auth_data->timeout_started = true;
+			run_again(sdata, ifmgd->auth_data->timeout);
 			goto notify_driver;
+		}
 
 		sdata_info(sdata, "%pM denied authentication (status %d)\n",
 			   mgmt->sa, status_code);
@@ -3290,8 +3317,11 @@
 		aid = 0; /* TODO */
 	}
 	capab_info = le16_to_cpu(mgmt->u.assoc_resp.capab_info);
-	ieee802_11_parse_elems(pos, len - (pos - (u8 *)mgmt), false, elems,
-			       mgmt->bssid, assoc_data->bss->bssid);
+	elems = ieee802_11_parse_elems(pos, len - (pos - (u8 *)mgmt), false,
+				       mgmt->bssid, assoc_data->bss->bssid);
+
+	if (!elems)
+		return false;
 
 	if (elems->aid_resp)
 		aid = le16_to_cpu(elems->aid_resp->aid);
@@ -3313,7 +3343,8 @@
 
 	if (!is_s1g && !elems->supp_rates) {
 		sdata_info(sdata, "no SuppRates element in AssocResp\n");
-		return false;
+		ret = false;
+		goto out;
 	}
 
 	sdata->vif.bss_conf.aid = aid;
@@ -3335,7 +3366,7 @@
 	     (!(ifmgd->flags & IEEE80211_STA_DISABLE_VHT) &&
 	      (!elems->vht_cap_elem || !elems->vht_operation)))) {
 		const struct cfg80211_bss_ies *ies;
-		struct ieee802_11_elems bss_elems;
+		struct ieee802_11_elems *bss_elems;
 
 		rcu_read_lock();
 		ies = rcu_dereference(cbss->ies);
@@ -3343,16 +3374,22 @@
 			bss_ies = kmemdup(ies, sizeof(*ies) + ies->len,
 					  GFP_ATOMIC);
 		rcu_read_unlock();
-		if (!bss_ies)
-			return false;
+		if (!bss_ies) {
+			ret = false;
+			goto out;
+		}
+
+		bss_elems = ieee802_11_parse_elems(bss_ies->data, bss_ies->len,
+						   false, mgmt->bssid,
+						   assoc_data->bss->bssid);
+		if (!bss_elems) {
+			ret = false;
+			goto out;
+		}
 
-		ieee802_11_parse_elems(bss_ies->data, bss_ies->len,
-				       false, &bss_elems,
-				       mgmt->bssid,
-				       assoc_data->bss->bssid);
 		if (assoc_data->wmm &&
-		    !elems->wmm_param && bss_elems.wmm_param) {
-			elems->wmm_param = bss_elems.wmm_param;
+		    !elems->wmm_param && bss_elems->wmm_param) {
+			elems->wmm_param = bss_elems->wmm_param;
 			sdata_info(sdata,
 				   "AP bug: WMM param missing from AssocResp\n");
 		}
@@ -3361,30 +3398,32 @@
 		 * Also check if we requested HT/VHT, otherwise the AP doesn't
 		 * have to include the IEs in the (re)association response.
 		 */
-		if (!elems->ht_cap_elem && bss_elems.ht_cap_elem &&
+		if (!elems->ht_cap_elem && bss_elems->ht_cap_elem &&
 		    !(ifmgd->flags & IEEE80211_STA_DISABLE_HT)) {
-			elems->ht_cap_elem = bss_elems.ht_cap_elem;
+			elems->ht_cap_elem = bss_elems->ht_cap_elem;
 			sdata_info(sdata,
 				   "AP bug: HT capability missing from AssocResp\n");
 		}
-		if (!elems->ht_operation && bss_elems.ht_operation &&
+		if (!elems->ht_operation && bss_elems->ht_operation &&
 		    !(ifmgd->flags & IEEE80211_STA_DISABLE_HT)) {
-			elems->ht_operation = bss_elems.ht_operation;
+			elems->ht_operation = bss_elems->ht_operation;
 			sdata_info(sdata,
 				   "AP bug: HT operation missing from AssocResp\n");
 		}
-		if (!elems->vht_cap_elem && bss_elems.vht_cap_elem &&
+		if (!elems->vht_cap_elem && bss_elems->vht_cap_elem &&
 		    !(ifmgd->flags & IEEE80211_STA_DISABLE_VHT)) {
-			elems->vht_cap_elem = bss_elems.vht_cap_elem;
+			elems->vht_cap_elem = bss_elems->vht_cap_elem;
 			sdata_info(sdata,
 				   "AP bug: VHT capa missing from AssocResp\n");
 		}
-		if (!elems->vht_operation && bss_elems.vht_operation &&
+		if (!elems->vht_operation && bss_elems->vht_operation &&
 		    !(ifmgd->flags & IEEE80211_STA_DISABLE_VHT)) {
-			elems->vht_operation = bss_elems.vht_operation;
+			elems->vht_operation = bss_elems->vht_operation;
 			sdata_info(sdata,
 				   "AP bug: VHT operation missing from AssocResp\n");
 		}
+
+		kfree(bss_elems);
 	}
 
 	/*
@@ -3515,6 +3554,12 @@
 				cbss->transmitted_bss->bssid);
 		bss_conf->bssid_indicator = cbss->max_bssid_indicator;
 		bss_conf->bssid_index = cbss->bssid_index;
+	} else {
+		bss_conf->nontransmitted = false;
+		memset(bss_conf->transmitter_bssid, 0,
+		       sizeof(bss_conf->transmitter_bssid));
+		bss_conf->bssid_indicator = 0;
+		bss_conf->bssid_index = 0;
 	}
 
 	/*
@@ -3629,6 +3674,7 @@
 
 	ret = true;
  out:
+	kfree(elems);
 	kfree(bss_ies);
 	return ret;
 }
@@ -3640,7 +3686,7 @@
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
 	struct ieee80211_mgd_assoc_data *assoc_data = ifmgd->assoc_data;
 	u16 capab_info, status_code, aid;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	int ac, uapsd_queues = -1;
 	u8 *pos;
 	bool reassoc;
@@ -3697,14 +3743,16 @@
 	    fils_decrypt_assoc_resp(sdata, (u8 *)mgmt, &len, assoc_data) < 0)
 		return;
 
-	ieee802_11_parse_elems(pos, len - (pos - (u8 *)mgmt), false, &elems,
-			       mgmt->bssid, assoc_data->bss->bssid);
+	elems = ieee802_11_parse_elems(pos, len - (pos - (u8 *)mgmt), false,
+				       mgmt->bssid, assoc_data->bss->bssid);
+	if (!elems)
+		goto notify_driver;
 
 	if (status_code == WLAN_STATUS_ASSOC_REJECTED_TEMPORARILY &&
-	    elems.timeout_int &&
-	    elems.timeout_int->type == WLAN_TIMEOUT_ASSOC_COMEBACK) {
+	    elems->timeout_int &&
+	    elems->timeout_int->type == WLAN_TIMEOUT_ASSOC_COMEBACK) {
 		u32 tu, ms;
-		tu = le32_to_cpu(elems.timeout_int->value);
+		tu = le32_to_cpu(elems->timeout_int->value);
 		ms = tu * 1024 / 1000;
 		sdata_info(sdata,
 			   "%pM rejected association temporarily; comeback duration %u TU (%u ms)\n",
@@ -3724,7 +3772,7 @@
 		event.u.mlme.reason = status_code;
 		drv_event_callback(sdata->local, sdata, &event);
 	} else {
-		if (!ieee80211_assoc_success(sdata, cbss, mgmt, len, &elems)) {
+		if (!ieee80211_assoc_success(sdata, cbss, mgmt, len, elems)) {
 			/* oops -- internal error -- send timeout for now */
 			ieee80211_destroy_assoc_data(sdata, false, false);
 			cfg80211_assoc_timeout(sdata->dev, cbss);
@@ -3754,6 +3802,7 @@
 			       ifmgd->assoc_req_ies, ifmgd->assoc_req_ies_len);
 notify_driver:
 	drv_mgd_complete_tx(sdata->local, sdata, &info);
+	kfree(elems);
 }
 
 static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
@@ -3958,7 +4007,7 @@
 	struct ieee80211_bss_conf *bss_conf = &sdata->vif.bss_conf;
 	struct ieee80211_mgmt *mgmt = (void *) hdr;
 	size_t baselen;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_chanctx_conf *chanctx_conf;
 	struct ieee80211_channel *chan;
@@ -4004,15 +4053,16 @@
 
 	if (ifmgd->assoc_data && ifmgd->assoc_data->need_beacon &&
 	    ieee80211_rx_our_beacon(bssid, ifmgd->assoc_data->bss)) {
-		ieee802_11_parse_elems(variable,
-				       len - baselen, false, &elems,
-				       bssid,
-				       ifmgd->assoc_data->bss->bssid);
+		elems = ieee802_11_parse_elems(variable, len - baselen, false,
+					       bssid,
+					       ifmgd->assoc_data->bss->bssid);
+		if (!elems)
+			return;
 
 		ieee80211_rx_bss_info(sdata, mgmt, len, rx_status);
 
-		if (elems.dtim_period)
-			ifmgd->dtim_period = elems.dtim_period;
+		if (elems->dtim_period)
+			ifmgd->dtim_period = elems->dtim_period;
 		ifmgd->have_beacon = true;
 		ifmgd->assoc_data->need_beacon = false;
 		if (ieee80211_hw_check(&local->hw, TIMING_BEACON_ONLY)) {
@@ -4020,17 +4070,17 @@
 				le64_to_cpu(mgmt->u.beacon.timestamp);
 			sdata->vif.bss_conf.sync_device_ts =
 				rx_status->device_timestamp;
-			sdata->vif.bss_conf.sync_dtim_count = elems.dtim_count;
+			sdata->vif.bss_conf.sync_dtim_count = elems->dtim_count;
 		}
 
-		if (elems.mbssid_config_ie)
+		if (elems->mbssid_config_ie)
 			bss_conf->profile_periodicity =
-				elems.mbssid_config_ie->profile_periodicity;
+				elems->mbssid_config_ie->profile_periodicity;
 		else
 			bss_conf->profile_periodicity = 0;
 
-		if (elems.ext_capab_len >= 11 &&
-		    (elems.ext_capab[10] & WLAN_EXT_CAPA11_EMA_SUPPORT))
+		if (elems->ext_capab_len >= 11 &&
+		    (elems->ext_capab[10] & WLAN_EXT_CAPA11_EMA_SUPPORT))
 			bss_conf->ema_ap = true;
 		else
 			bss_conf->ema_ap = false;
@@ -4039,6 +4089,7 @@
 		ifmgd->assoc_data->timeout = jiffies;
 		ifmgd->assoc_data->timeout_started = true;
 		run_again(sdata, ifmgd->assoc_data->timeout);
+		kfree(elems);
 		return;
 	}
 
@@ -4070,13 +4121,15 @@
 	 */
 	if (!ieee80211_is_s1g_beacon(hdr->frame_control))
 		ncrc = crc32_be(0, (void *)&mgmt->u.beacon.beacon_int, 4);
-	ncrc = ieee802_11_parse_elems_crc(variable,
-					  len - baselen, false, &elems,
-					  care_about_ies, ncrc,
-					  mgmt->bssid, bssid);
+	elems = ieee802_11_parse_elems_crc(variable, len - baselen,
+					   false, care_about_ies, ncrc,
+					   mgmt->bssid, bssid);
+	if (!elems)
+		return;
+	ncrc = elems->crc;
 
 	if (ieee80211_hw_check(&local->hw, PS_NULLFUNC_STACK) &&
-	    ieee80211_check_tim(elems.tim, elems.tim_len, bss_conf->aid)) {
+	    ieee80211_check_tim(elems->tim, elems->tim_len, bss_conf->aid)) {
 		if (local->hw.conf.dynamic_ps_timeout > 0) {
 			if (local->hw.conf.flags & IEEE80211_CONF_PS) {
 				local->hw.conf.flags &= ~IEEE80211_CONF_PS;
@@ -4146,12 +4199,12 @@
 			le64_to_cpu(mgmt->u.beacon.timestamp);
 		sdata->vif.bss_conf.sync_device_ts =
 			rx_status->device_timestamp;
-		sdata->vif.bss_conf.sync_dtim_count = elems.dtim_count;
+		sdata->vif.bss_conf.sync_dtim_count = elems->dtim_count;
 	}
 
 	if ((ncrc == ifmgd->beacon_crc && ifmgd->beacon_crc_valid) ||
 	    ieee80211_is_s1g_short_beacon(mgmt->frame_control))
-		return;
+		goto free;
 	ifmgd->beacon_crc = ncrc;
 	ifmgd->beacon_crc_valid = true;
 
@@ -4159,12 +4212,12 @@
 
 	ieee80211_sta_process_chanswitch(sdata, rx_status->mactime,
 					 rx_status->device_timestamp,
-					 &elems, true);
+					 elems, true);
 
 	if (!(ifmgd->flags & IEEE80211_STA_DISABLE_WMM) &&
-	    ieee80211_sta_wmm_params(local, sdata, elems.wmm_param,
-				     elems.wmm_param_len,
-				     elems.mu_edca_param_set))
+	    ieee80211_sta_wmm_params(local, sdata, elems->wmm_param,
+				     elems->wmm_param_len,
+				     elems->mu_edca_param_set))
 		changed |= BSS_CHANGED_QOS;
 
 	/*
@@ -4173,7 +4226,7 @@
 	 */
 	if (!ifmgd->have_beacon) {
 		/* a few bogus AP send dtim_period = 0 or no TIM IE */
-		bss_conf->dtim_period = elems.dtim_period ?: 1;
+		bss_conf->dtim_period = elems->dtim_period ?: 1;
 
 		changed |= BSS_CHANGED_BEACON_INFO;
 		ifmgd->have_beacon = true;
@@ -4185,9 +4238,9 @@
 		ieee80211_recalc_ps_vif(sdata);
 	}
 
-	if (elems.erp_info) {
+	if (elems->erp_info) {
 		erp_valid = true;
-		erp_value = elems.erp_info[0];
+		erp_value = elems->erp_info[0];
 	} else {
 		erp_valid = false;
 	}
@@ -4200,12 +4253,12 @@
 	mutex_lock(&local->sta_mtx);
 	sta = sta_info_get(sdata, bssid);
 
-	changed |= ieee80211_recalc_twt_req(sdata, sta, &elems);
+	changed |= ieee80211_recalc_twt_req(sdata, sta, elems);
 
-	if (ieee80211_config_bw(sdata, sta, elems.ht_cap_elem,
-				elems.vht_cap_elem, elems.ht_operation,
-				elems.vht_operation, elems.he_operation,
-				elems.s1g_oper, bssid, &changed)) {
+	if (ieee80211_config_bw(sdata, sta, elems->ht_cap_elem,
+				elems->vht_cap_elem, elems->ht_operation,
+				elems->vht_operation, elems->he_operation,
+				elems->s1g_oper, bssid, &changed)) {
 		mutex_unlock(&local->sta_mtx);
 		sdata_info(sdata,
 			   "failed to follow AP %pM bandwidth change, disconnect\n",
@@ -4217,21 +4270,23 @@
 					    sizeof(deauth_buf), true,
 					    WLAN_REASON_DEAUTH_LEAVING,
 					    false);
-		return;
+		goto free;
 	}
 
-	if (sta && elems.opmode_notif)
-		ieee80211_vht_handle_opmode(sdata, sta, *elems.opmode_notif,
+	if (sta && elems->opmode_notif)
+		ieee80211_vht_handle_opmode(sdata, sta, *elems->opmode_notif,
 					    rx_status->band);
 	mutex_unlock(&local->sta_mtx);
 
 	changed |= ieee80211_handle_pwr_constr(sdata, chan, mgmt,
-					       elems.country_elem,
-					       elems.country_elem_len,
-					       elems.pwr_constr_elem,
-					       elems.cisco_dtpc_elem);
+					       elems->country_elem,
+					       elems->country_elem_len,
+					       elems->pwr_constr_elem,
+					       elems->cisco_dtpc_elem);
 
 	ieee80211_bss_info_change_notify(sdata, changed);
+free:
+	kfree(elems);
 }
 
 void ieee80211_sta_rx_queued_ext(struct ieee80211_sub_if_data *sdata,
@@ -4260,7 +4315,6 @@
 	struct ieee80211_rx_status *rx_status;
 	struct ieee80211_mgmt *mgmt;
 	u16 fc;
-	struct ieee802_11_elems elems;
 	int ies_len;
 
 	rx_status = (struct ieee80211_rx_status *) skb->cb;
@@ -4292,6 +4346,8 @@
 		break;
 	case IEEE80211_STYPE_ACTION:
 		if (mgmt->u.action.category == WLAN_CATEGORY_SPECTRUM_MGMT) {
+			struct ieee802_11_elems *elems;
+
 			ies_len = skb->len -
 				  offsetof(struct ieee80211_mgmt,
 					   u.action.u.chan_switch.variable);
@@ -4300,18 +4356,19 @@
 				break;
 
 			/* CSA IE cannot be overridden, no need for BSSID */
-			ieee802_11_parse_elems(
-				mgmt->u.action.u.chan_switch.variable,
-				ies_len, true, &elems, mgmt->bssid, NULL);
-
-			if (elems.parse_error)
-				break;
-
-			ieee80211_sta_process_chanswitch(sdata,
-						 rx_status->mactime,
-						 rx_status->device_timestamp,
-						 &elems, false);
+			elems = ieee802_11_parse_elems(
+					mgmt->u.action.u.chan_switch.variable,
+					ies_len, true, mgmt->bssid, NULL);
+
+			if (elems && !elems->parse_error)
+				ieee80211_sta_process_chanswitch(sdata,
+								 rx_status->mactime,
+								 rx_status->device_timestamp,
+								 elems, false);
+			kfree(elems);
 		} else if (mgmt->u.action.category == WLAN_CATEGORY_PUBLIC) {
+			struct ieee802_11_elems *elems;
+
 			ies_len = skb->len -
 				  offsetof(struct ieee80211_mgmt,
 					   u.action.u.ext_chan_switch.variable);
@@ -4323,21 +4380,22 @@
 			 * extended CSA IE can't be overridden, no need for
 			 * BSSID
 			 */
-			ieee802_11_parse_elems(
-				mgmt->u.action.u.ext_chan_switch.variable,
-				ies_len, true, &elems, mgmt->bssid, NULL);
-
-			if (elems.parse_error)
-				break;
+			elems = ieee802_11_parse_elems(
+					mgmt->u.action.u.ext_chan_switch.variable,
+					ies_len, true, mgmt->bssid, NULL);
+
+			if (elems && !elems->parse_error) {
+				/* for the handling code pretend it was an IE */
+				elems->ext_chansw_ie =
+					&mgmt->u.action.u.ext_chan_switch.data;
+
+				ieee80211_sta_process_chanswitch(sdata,
+								 rx_status->mactime,
+								 rx_status->device_timestamp,
+								 elems, false);
+			}
 
-			/* for the handling code pretend this was also an IE */
-			elems.ext_chansw_ie =
-				&mgmt->u.action.u.ext_chan_switch.data;
-
-			ieee80211_sta_process_chanswitch(sdata,
-						 rx_status->mactime,
-						 rx_status->device_timestamp,
-						 &elems, false);
+			kfree(elems);
 		}
 		break;
 	}
@@ -4444,6 +4502,7 @@
 {
 	struct ieee80211_mgd_assoc_data *assoc_data = sdata->u.mgd.assoc_data;
 	struct ieee80211_local *local = sdata->local;
+	int ret;
 
 	sdata_assert_lock(sdata);
 
@@ -4464,7 +4523,9 @@
 	sdata_info(sdata, "associate with %pM (try %d/%d)\n",
 		   assoc_data->bss->bssid, assoc_data->tries,
 		   IEEE80211_ASSOC_MAX_TRIES);
-	ieee80211_send_assoc(sdata);
+	ret = ieee80211_send_assoc(sdata);
+	if (ret)
+		return ret;
 
 	if (!ieee80211_hw_check(&local->hw, REPORTS_TX_ACK_STATUS)) {
 		assoc_data->timeout = jiffies + IEEE80211_ASSOC_TIMEOUT;
@@ -4537,10 +4598,10 @@
 
 	if (ifmgd->auth_data && ifmgd->auth_data->timeout_started &&
 	    time_after(jiffies, ifmgd->auth_data->timeout)) {
-		if (ifmgd->auth_data->done) {
+		if (ifmgd->auth_data->done || ifmgd->auth_data->waiting) {
 			/*
-			 * ok ... we waited for assoc but userspace didn't,
-			 * so let's just kill the auth data
+			 * ok ... we waited for assoc or continuation but
+			 * userspace didn't do it, so kill the auth data
 			 */
 			ieee80211_destroy_auth_data(sdata, false);
 		} else if (ieee80211_auth(sdata)) {
@@ -4771,6 +4832,7 @@
 
 	sdata_unlock(sdata);
 }
+#endif
 
 void ieee80211_sta_restart(struct ieee80211_sub_if_data *sdata)
 {
@@ -4792,9 +4854,20 @@
 		sdata_unlock(sdata);
 		return;
 	}
+
+	if (sdata->flags & IEEE80211_SDATA_DISCONNECT_HW_RESTART) {
+		sdata->flags &= ~IEEE80211_SDATA_DISCONNECT_HW_RESTART;
+		mlme_dbg(sdata, "driver requested disconnect after hardware restart\n");
+		ieee80211_sta_connection_lost(sdata,
+					      ifmgd->associated->bssid,
+					      WLAN_REASON_UNSPECIFIED,
+					      true);
+		sdata_unlock(sdata);
+		return;
+	}
+
 	sdata_unlock(sdata);
 }
-#endif
 
 /* interface setup */
 void ieee80211_sta_setup_sdata(struct ieee80211_sub_if_data *sdata)
@@ -5209,7 +5282,7 @@
 	 */
 	if (new_sta) {
 		u32 rates = 0, basic_rates = 0;
-		bool have_higher_than_11mbit;
+		bool have_higher_than_11mbit = false;
 		int min_rate = INT_MAX, min_rate_index = -1;
 		const struct cfg80211_bss_ies *ies;
 		int shift = ieee80211_vif_get_shift(&sdata->vif);
@@ -5862,6 +5935,7 @@
 		ieee80211_report_disconnect(sdata, frame_buf,
 					    sizeof(frame_buf), true,
 					    req->reason_code, false);
+		drv_mgd_complete_tx(sdata->local, sdata, &info);
 		return 0;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/rc80211_minstrel_ht.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/rc80211_minstrel_ht.c
@@ -364,6 +364,9 @@
 
 	group = MINSTREL_CCK_GROUP;
 	for (idx = 0; idx < ARRAY_SIZE(mp->cck_rates); idx++) {
+		if (!(mi->supported[group] & BIT(idx)))
+			continue;
+
 		if (rate->idx != mp->cck_rates[idx])
 			continue;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/rx.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/rx.c
@@ -364,7 +364,7 @@
 	 * the compiler to think we have walked past the end of the
 	 * struct member.
 	 */
-	pos = (void *)&rthdr->it_optional[it_present - rthdr->it_optional];
+	pos = (void *)&rthdr->it_optional[it_present + 1 - rthdr->it_optional];
 
 	/* the order of the following fields is important */
 
@@ -1400,8 +1400,7 @@
 		goto dont_reorder;
 
 	/* not part of a BA session */
-	if (ack_policy != IEEE80211_QOS_CTL_ACK_POLICY_BLOCKACK &&
-	    ack_policy != IEEE80211_QOS_CTL_ACK_POLICY_NORMAL)
+	if (ack_policy == IEEE80211_QOS_CTL_ACK_POLICY_NOACK)
 		goto dont_reorder;
 
 	/* new, potentially un-ordered, ampdu frame - process it */
@@ -1952,7 +1951,8 @@
 		int keyid = rx->sta->ptk_idx;
 		sta_ptk = rcu_dereference(rx->sta->ptk[keyid]);
 
-		if (ieee80211_has_protected(fc)) {
+		if (ieee80211_has_protected(fc) &&
+		    !(status->flag & RX_FLAG_IV_STRIPPED)) {
 			cs = rx->sta->cipher_scheme;
 			keyid = ieee80211_get_keyid(rx->skb, cs);
 
@@ -1982,10 +1982,11 @@
 
 		if (mmie_keyidx < NUM_DEFAULT_KEYS + NUM_DEFAULT_MGMT_KEYS ||
 		    mmie_keyidx >= NUM_DEFAULT_KEYS + NUM_DEFAULT_MGMT_KEYS +
-		    NUM_DEFAULT_BEACON_KEYS) {
-			cfg80211_rx_unprot_mlme_mgmt(rx->sdata->dev,
-						     skb->data,
-						     skb->len);
+				   NUM_DEFAULT_BEACON_KEYS) {
+			if (rx->sdata->dev)
+				cfg80211_rx_unprot_mlme_mgmt(rx->sdata->dev,
+							     skb->data,
+							     skb->len);
 			return RX_DROP_MONITOR; /* unexpected BIP keyidx */
 		}
 
@@ -2133,7 +2134,8 @@
 	/* either the frame has been decrypted or will be dropped */
 	status->flag |= RX_FLAG_DECRYPTED;
 
-	if (unlikely(ieee80211_is_beacon(fc) && result == RX_DROP_UNUSABLE))
+	if (unlikely(ieee80211_is_beacon(fc) && result == RX_DROP_UNUSABLE &&
+		     rx->sdata->dev))
 		cfg80211_rx_unprot_mlme_mgmt(rx->sdata->dev,
 					     skb->data, skb->len);
 
@@ -2601,7 +2603,8 @@
 		 * address, so that the authenticator (e.g. hostapd) will see
 		 * the frame, but bridge won't forward it anywhere else. Note
 		 * that due to earlier filtering, the only other address can
-		 * be the PAE group address.
+		 * be the PAE group address, unless the hardware allowed them
+		 * through in 802.3 offloaded mode.
 		 */
 		if (unlikely(skb->protocol == sdata->control_port_protocol &&
 			     !ether_addr_equal(ehdr->h_dest, sdata->vif.addr)))
@@ -2916,13 +2919,13 @@
 	    ether_addr_equal(sdata->vif.addr, hdr->addr3))
 		return RX_CONTINUE;
 
-	ac = ieee80211_select_queue_80211(sdata, skb, hdr);
+	ac = ieee802_1d_to_ac[skb->priority];
 	q = sdata->vif.hw_queue[ac];
 	if (ieee80211_queue_stopped(&local->hw, q)) {
 		IEEE80211_IFSTA_MESH_CTR_INC(ifmsh, dropped_frames_congestion);
 		return RX_DROP_MONITOR;
 	}
-	skb_set_queue_mapping(skb, q);
+	skb_set_queue_mapping(skb, ac);
 
 	if (!--mesh_hdr->ttl) {
 		if (!is_multicast_ether_addr(hdr->addr1))
@@ -3554,6 +3557,10 @@
 			break;
 		goto queue;
 	case WLAN_CATEGORY_S1G:
+		if (len < offsetofend(typeof(*mgmt),
+				      u.action.u.s1g.action_code))
+			break;
+
 		switch (mgmt->u.action.u.s1g.action_code) {
 		case WLAN_S1G_TWT_SETUP:
 		case WLAN_S1G_TWT_TEARDOWN:
@@ -4517,12 +4524,7 @@
 
 	/* deliver to local stack */
 	skb->protocol = eth_type_trans(skb, fast_rx->dev);
-	memset(skb->cb, 0, sizeof(skb->cb));
-	if (rx->list)
-		list_add_tail(&skb->list, rx->list);
-	else
-		netif_receive_skb(skb);
-
+	ieee80211_deliver_skb_to_local_stack(skb, rx);
 }
 
 static bool ieee80211_invoke_fast_rx(struct ieee80211_rx_data *rx,
@@ -4873,6 +4875,7 @@
 	struct ieee80211_rate *rate = NULL;
 	struct ieee80211_supported_band *sband;
 	struct ieee80211_rx_status *status = IEEE80211_SKB_RXCB(skb);
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
 
 	WARN_ON_ONCE(softirq_count() == 0);
 
@@ -4931,7 +4934,7 @@
 				goto drop;
 			break;
 		case RX_ENC_VHT:
-			if (WARN_ONCE(status->rate_idx > 9 ||
+			if (WARN_ONCE(status->rate_idx > 11 ||
 				      !status->nss ||
 				      status->nss > 8,
 				      "Rate marked as a VHT rate but data is invalid: MCS: %d, NSS: %d\n",
@@ -4969,9 +4972,9 @@
 	if (!(status->flag & RX_FLAG_8023))
 		skb = ieee80211_rx_monitor(local, skb, rate);
 	if (skb) {
-		ieee80211_tpt_led_trig_rx(local,
-					  ((struct ieee80211_hdr *)skb->data)->frame_control,
-					  skb->len);
+		if ((status->flag & RX_FLAG_8023) ||
+			ieee80211_is_data_present(hdr->frame_control))
+			ieee80211_tpt_led_trig_rx(local, skb->len);
 
 		if (status->flag & RX_FLAG_8023)
 			__ieee80211_rx_handle_8023(hw, pubsta, skb, list);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/s1g.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/s1g.c
@@ -104,12 +104,17 @@
 
 	/* broadcast TWT not supported yet */
 	if (twt->control & IEEE80211_TWT_CONTROL_NEG_TYPE_BROADCAST) {
-		le16p_replace_bits(&twt_agrt->req_type,
-				   TWT_SETUP_CMD_REJECT,
-				   IEEE80211_TWT_REQTYPE_SETUP_CMD);
+		twt_agrt->req_type &=
+			~cpu_to_le16(IEEE80211_TWT_REQTYPE_SETUP_CMD);
+		twt_agrt->req_type |=
+			le16_encode_bits(TWT_SETUP_CMD_REJECT,
+					 IEEE80211_TWT_REQTYPE_SETUP_CMD);
 		goto out;
 	}
 
+	/* TWT Information not supported yet */
+	twt->control |= IEEE80211_TWT_CONTROL_RX_DISABLED;
+
 	drv_add_twt_setup(sdata->local, sdata, &sta->sta, twt);
 out:
 	ieee80211_s1g_send_twt_setup(sdata, mgmt->sa, sdata->vif.addr, twt);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/scan.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/scan.c
@@ -9,7 +9,7 @@
  * Copyright 2007, Michael Wu <flamingice@sourmilk.net>
  * Copyright 2013-2015  Intel Mobile Communications GmbH
  * Copyright 2016-2017  Intel Deutschland GmbH
- * Copyright (C) 2018-2020 Intel Corporation
+ * Copyright (C) 2018-2021 Intel Corporation
  */
 
 #include <linux/if_arp.h>
@@ -155,7 +155,7 @@
 	};
 	bool signal_valid;
 	struct ieee80211_sub_if_data *scan_sdata;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	size_t baselen;
 	u8 *elements;
 
@@ -209,8 +209,10 @@
 	if (baselen > len)
 		return NULL;
 
-	ieee802_11_parse_elems(elements, len - baselen, false, &elems,
-			       mgmt->bssid, cbss->bssid);
+	elems = ieee802_11_parse_elems(elements, len - baselen, false,
+				       mgmt->bssid, cbss->bssid);
+	if (!elems)
+		return NULL;
 
 	/* In case the signal is invalid update the status */
 	signal_valid = channel == cbss->channel;
@@ -218,15 +220,17 @@
 		rx_status->flag |= RX_FLAG_NO_SIGNAL_VAL;
 
 	bss = (void *)cbss->priv;
-	ieee80211_update_bss_from_elems(local, bss, &elems, rx_status, beacon);
+	ieee80211_update_bss_from_elems(local, bss, elems, rx_status, beacon);
 
 	list_for_each_entry(non_tx_cbss, &cbss->nontrans_list, nontrans_list) {
 		non_tx_bss = (void *)non_tx_cbss->priv;
 
-		ieee80211_update_bss_from_elems(local, non_tx_bss, &elems,
+		ieee80211_update_bss_from_elems(local, non_tx_bss, elems,
 						rx_status, beacon);
 	}
 
+	kfree(elems);
+
 	return bss;
 }
 
@@ -277,6 +281,16 @@
 	if (likely(!sdata1 && !sdata2))
 		return;
 
+	if (test_and_clear_bit(SCAN_BEACON_WAIT, &local->scanning)) {
+		/*
+		 * we were passive scanning because of radar/no-IR, but
+		 * the beacon/proberesp rx gives us an opportunity to upgrade
+		 * to active scan
+		 */
+		 set_bit(SCAN_BEACON_DONE, &local->scanning);
+		 ieee80211_queue_delayed_work(&local->hw, &local->scan_work, 0);
+	}
+
 	if (ieee80211_is_probe_resp(mgmt->frame_control)) {
 		struct cfg80211_scan_request *scan_req;
 		struct cfg80211_sched_scan_request *sched_scan_req;
@@ -339,7 +353,8 @@
 	struct cfg80211_scan_request *req;
 	struct cfg80211_chan_def chandef;
 	u8 bands_used = 0;
-	int i, ielen, n_chans;
+	int i, ielen;
+	u32 *n_chans;
 	u32 flags = 0;
 
 	req = rcu_dereference_protected(local->scan_req,
@@ -349,34 +364,34 @@
 		return false;
 
 	if (ieee80211_hw_check(&local->hw, SINGLE_SCAN_ON_ALL_BANDS)) {
+		local->hw_scan_req->req.n_channels = req->n_channels;
+
 		for (i = 0; i < req->n_channels; i++) {
 			local->hw_scan_req->req.channels[i] = req->channels[i];
 			bands_used |= BIT(req->channels[i]->band);
 		}
-
-		n_chans = req->n_channels;
 	} else {
 		do {
 			if (local->hw_scan_band == NUM_NL80211_BANDS)
 				return false;
 
-			n_chans = 0;
+			n_chans = &local->hw_scan_req->req.n_channels;
+			*n_chans = 0;
 
 			for (i = 0; i < req->n_channels; i++) {
 				if (req->channels[i]->band !=
 				    local->hw_scan_band)
 					continue;
-				local->hw_scan_req->req.channels[n_chans] =
+				local->hw_scan_req->req.channels[(*n_chans)++] =
 							req->channels[i];
-				n_chans++;
+
 				bands_used |= BIT(req->channels[i]->band);
 			}
 
 			local->hw_scan_band++;
-		} while (!n_chans);
+		} while (!*n_chans);
 	}
 
-	local->hw_scan_req->req.n_channels = n_chans;
 	ieee80211_prepare_scan_chandef(&chandef, req->scan_width);
 
 	if (req->flags & NL80211_SCAN_FLAG_MIN_PREQ_CONTENT)
@@ -451,16 +466,19 @@
 	scan_req = rcu_dereference_protected(local->scan_req,
 					     lockdep_is_held(&local->mtx));
 
-	if (scan_req != local->int_scan_req) {
-		local->scan_info.aborted = aborted;
-		cfg80211_scan_done(scan_req, &local->scan_info);
-	}
 	RCU_INIT_POINTER(local->scan_req, NULL);
 	RCU_INIT_POINTER(local->scan_sdata, NULL);
 
 	local->scanning = 0;
 	local->scan_chandef.chan = NULL;
 
+	synchronize_rcu();
+
+	if (scan_req != local->int_scan_req) {
+		local->scan_info.aborted = aborted;
+		cfg80211_scan_done(scan_req, &local->scan_info);
+	}
+
 	/* Set power back to normal operating levels. */
 	ieee80211_hw_config(local, 0);
 
@@ -712,15 +730,21 @@
 			local->hw_scan_ies_bufsize *= n_bands;
 		}
 
-		local->hw_scan_req = kmalloc(
-				sizeof(*local->hw_scan_req) +
-				req->n_channels * sizeof(req->channels[0]) +
-				local->hw_scan_ies_bufsize, GFP_KERNEL);
+		local->hw_scan_req = kmalloc(struct_size(local->hw_scan_req,
+							 req.channels,
+							 req->n_channels) +
+					     local->hw_scan_ies_bufsize,
+					     GFP_KERNEL);
 		if (!local->hw_scan_req)
 			return -ENOMEM;
 
 		local->hw_scan_req->req.ssids = req->ssids;
 		local->hw_scan_req->req.n_ssids = req->n_ssids;
+		/* None of the channels are actually set
+		 * up but let UBSAN know the boundaries.
+		 */
+		local->hw_scan_req->req.n_channels = req->n_channels;
+
 		ies = (u8 *)local->hw_scan_req +
 			sizeof(*local->hw_scan_req) +
 			req->n_channels * sizeof(req->channels[0]);
@@ -783,6 +807,8 @@
 						IEEE80211_CHAN_RADAR)) ||
 		    !req->n_ssids) {
 			next_delay = IEEE80211_PASSIVE_CHANNEL_TIME;
+			if (req->n_ssids)
+				set_bit(SCAN_BEACON_WAIT, &local->scanning);
 		} else {
 			ieee80211_scan_state_send_probe(local, &next_delay);
 			next_delay = IEEE80211_CHANNEL_TIME;
@@ -994,6 +1020,8 @@
 	    !scan_req->n_ssids) {
 		*next_delay = IEEE80211_PASSIVE_CHANNEL_TIME;
 		local->next_scan_state = SCAN_DECISION;
+		if (scan_req->n_ssids)
+			set_bit(SCAN_BEACON_WAIT, &local->scanning);
 		return;
 	}
 
@@ -1086,6 +1114,8 @@
 			goto out;
 	}
 
+	clear_bit(SCAN_BEACON_WAIT, &local->scanning);
+
 	/*
 	 * as long as no delay is required advance immediately
 	 * without scheduling a new work
@@ -1096,6 +1126,10 @@
 			goto out_complete;
 		}
 
+		if (test_and_clear_bit(SCAN_BEACON_DONE, &local->scanning) &&
+		    local->next_scan_state == SCAN_DECISION)
+			local->next_scan_state = SCAN_SEND_PROBE;
+
 		switch (local->next_scan_state) {
 		case SCAN_DECISION:
 			/* if no more bands/channels left, complete scan */
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/sta_info.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/sta_info.c
@@ -641,13 +641,13 @@
 	/* check if STA exists already */
 	if (sta_info_get_bss(sdata, sta->sta.addr)) {
 		err = -EEXIST;
-		goto out_err;
+		goto out_cleanup;
 	}
 
 	sinfo = kzalloc(sizeof(struct station_info), GFP_KERNEL);
 	if (!sinfo) {
 		err = -ENOMEM;
-		goto out_err;
+		goto out_cleanup;
 	}
 
 	local->num_sta++;
@@ -696,6 +696,8 @@
 	if (ieee80211_vif_is_mesh(&sdata->vif))
 		mesh_accept_plinks_update(sdata);
 
+	ieee80211_check_fast_xmit(sta);
+
 	return 0;
  out_remove:
 	sta_info_hash_del(local, sta);
@@ -703,8 +705,8 @@
  out_drop_sta:
 	local->num_sta--;
 	synchronize_net();
+ out_cleanup:
 	cleanup_single_sta(sta);
- out_err:
 	mutex_unlock(&local->sta_mtx);
 	kfree(sinfo);
 	rcu_read_lock();
@@ -1036,7 +1038,8 @@
 	list_del_rcu(&sta->list);
 	sta->removed = true;
 
-	drv_sta_pre_rcu_remove(local, sta->sdata, sta);
+	if (sta->uploaded)
+		drv_sta_pre_rcu_remove(local, sta->sdata, sta);
 
 	if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN &&
 	    rcu_access_pointer(sdata->u.vlan.sta) == sta)
@@ -1057,6 +1060,20 @@
 	 *	 after _part1 and before _part2!
 	 */
 
+	/*
+	 * There's a potential race in _part1 where we set WLAN_STA_BLOCK_BA
+	 * but someone might have just gotten past a check, and not yet into
+	 * queuing the work/creating the data/etc.
+	 *
+	 * Do another round of destruction so that the worker is certainly
+	 * canceled before we later free the station.
+	 *
+	 * Since this is after synchronize_rcu()/synchronize_net() we're now
+	 * certain that nobody can actually hold a reference to the STA and
+	 * be calling e.g. ieee80211_start_tx_ba_session().
+	 */
+	ieee80211_sta_tear_down_BA_sessions(sta, AGG_STOP_DESTROY_STA);
+
 	might_sleep();
 	lockdep_assert_held(&local->sta_mtx);
 
@@ -1336,7 +1353,7 @@
 	skb_queue_head_init(&pending);
 
 	/* sync with ieee80211_tx_h_unicast_ps_buf */
-	spin_lock(&sta->ps_lock);
+	spin_lock_bh(&sta->ps_lock);
 	/* Send all buffered frames to the station */
 	for (ac = 0; ac < IEEE80211_NUM_ACS; ac++) {
 		int count = skb_queue_len(&pending), tmp;
@@ -1365,7 +1382,7 @@
 	 */
 	clear_sta_flag(sta, WLAN_STA_PSPOLL);
 	clear_sta_flag(sta, WLAN_STA_UAPSD);
-	spin_unlock(&sta->ps_lock);
+	spin_unlock_bh(&sta->ps_lock);
 
 	atomic_dec(&ps->num_sta_ps);
 
@@ -2190,7 +2207,7 @@
 
 static int sta_set_rate_info_rx(struct sta_info *sta, struct rate_info *rinfo)
 {
-	u16 rate = READ_ONCE(sta_get_last_rx_stats(sta)->last_rate);
+	u32 rate = READ_ONCE(sta_get_last_rx_stats(sta)->last_rate);
 
 	if (rate == STA_STATS_RATE_INVALID)
 		return -EINVAL;
@@ -2206,9 +2223,9 @@
 	u64 value;
 
 	do {
-		start = u64_stats_fetch_begin(&rxstats->syncp);
+		start = u64_stats_fetch_begin_irq(&rxstats->syncp);
 		value = rxstats->msdu[tid];
-	} while (u64_stats_fetch_retry(&rxstats->syncp, start));
+	} while (u64_stats_fetch_retry_irq(&rxstats->syncp, start));
 
 	return value;
 }
@@ -2272,9 +2289,9 @@
 	u64 value;
 
 	do {
-		start = u64_stats_fetch_begin(&rxstats->syncp);
+		start = u64_stats_fetch_begin_irq(&rxstats->syncp);
 		value = rxstats->bytes;
-	} while (u64_stats_fetch_retry(&rxstats->syncp, start));
+	} while (u64_stats_fetch_retry_irq(&rxstats->syncp, start));
 
 	return value;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/sta_info.h
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/sta_info.h
@@ -199,6 +199,7 @@
 	u8 stop_initiator;
 	bool tx_stop;
 	u16 buf_size;
+	u16 ssn;
 
 	u16 failed_bar_ssn;
 	bool bar_pending;
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/status.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/status.c
@@ -5,6 +5,7 @@
  * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
  * Copyright 2008-2010	Johannes Berg <johannes@sipsolutions.net>
  * Copyright 2013-2014  Intel Mobile Communications GmbH
+ * Copyright 2021-2022  Intel Corporation
  */
 
 #include <linux/export.h>
@@ -628,6 +629,8 @@
 		u64 cookie = IEEE80211_SKB_CB(skb)->ack.cookie;
 		struct ieee80211_sub_if_data *sdata;
 		struct ieee80211_hdr *hdr = (void *)skb->data;
+		bool is_valid_ack_signal =
+			!!(info->status.flags & IEEE80211_TX_STATUS_ACK_SIGNAL_VALID);
 
 		rcu_read_lock();
 		sdata = ieee80211_sdata_from_skb(local, skb);
@@ -644,7 +647,7 @@
 				cfg80211_probe_status(sdata->dev, hdr->addr1,
 						      cookie, acked,
 						      info->status.ack_signal,
-						      info->status.is_valid_ack_signal,
+						      is_valid_ack_signal,
 						      GFP_ATOMIC);
 			else if (ieee80211_is_mgmt(hdr->frame_control))
 				cfg80211_mgmt_tx_status(&sdata->wdev, cookie,
@@ -1102,7 +1105,7 @@
 	struct ieee80211_supported_band *sband;
 	struct sta_info *sta = NULL;
 	int rates_idx, retry_count;
-	bool acked, noack_success;
+	bool acked, noack_success, ack_signal_valid;
 	u16 tx_time_est;
 
 	if (pubsta) {
@@ -1133,6 +1136,8 @@
 
 	acked = !!(info->flags & IEEE80211_TX_STAT_ACK);
 	noack_success = !!(info->flags & IEEE80211_TX_STAT_NOACK_TRANSMITTED);
+	ack_signal_valid =
+		!!(info->status.flags & IEEE80211_TX_STATUS_ACK_SIGNAL_VALID);
 
 	if (pubsta) {
 		struct ieee80211_sub_if_data *sdata = sta->sdata;
@@ -1161,7 +1166,7 @@
 				    unlikely(sdata->u.mgd.probe_send_count > 0))
 					sdata->u.mgd.probe_send_count = 0;
 
-				if (info->status.is_valid_ack_signal) {
+				if (ack_signal_valid) {
 					sta->status_stats.last_ack_signal =
 							 (s8)info->status.ack_signal;
 					sta->status_stats.ack_signal_filled = true;
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/tdls.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/tdls.c
@@ -6,7 +6,7 @@
  * Copyright 2014, Intel Corporation
  * Copyright 2014  Intel Mobile Communications GmbH
  * Copyright 2015 - 2016 Intel Deutschland GmbH
- * Copyright (C) 2019 Intel Corporation
+ * Copyright (C) 2019, 2021 Intel Corporation
  */
 
 #include <linux/ieee80211.h>
@@ -1684,7 +1684,7 @@
 					   struct sk_buff *skb)
 {
 	struct ieee80211_local *local = sdata->local;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems = NULL;
 	struct sta_info *sta;
 	struct ieee80211_tdls_data *tf = (void *)skb->data;
 	bool local_initiator;
@@ -1718,16 +1718,20 @@
 		goto call_drv;
 	}
 
-	ieee802_11_parse_elems(tf->u.chan_switch_resp.variable,
-			       skb->len - baselen, false, &elems,
-			       NULL, NULL);
-	if (elems.parse_error) {
+	elems = ieee802_11_parse_elems(tf->u.chan_switch_resp.variable,
+				       skb->len - baselen, false, NULL, NULL);
+	if (!elems) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	if (elems->parse_error) {
 		tdls_dbg(sdata, "Invalid IEs in TDLS channel switch resp\n");
 		ret = -EINVAL;
 		goto out;
 	}
 
-	if (!elems.ch_sw_timing || !elems.lnk_id) {
+	if (!elems->ch_sw_timing || !elems->lnk_id) {
 		tdls_dbg(sdata, "TDLS channel switch resp - missing IEs\n");
 		ret = -EINVAL;
 		goto out;
@@ -1735,15 +1739,15 @@
 
 	/* validate the initiator is set correctly */
 	local_initiator =
-		!memcmp(elems.lnk_id->init_sta, sdata->vif.addr, ETH_ALEN);
+		!memcmp(elems->lnk_id->init_sta, sdata->vif.addr, ETH_ALEN);
 	if (local_initiator == sta->sta.tdls_initiator) {
 		tdls_dbg(sdata, "TDLS chan switch invalid lnk-id initiator\n");
 		ret = -EINVAL;
 		goto out;
 	}
 
-	params.switch_time = le16_to_cpu(elems.ch_sw_timing->switch_time);
-	params.switch_timeout = le16_to_cpu(elems.ch_sw_timing->switch_timeout);
+	params.switch_time = le16_to_cpu(elems->ch_sw_timing->switch_time);
+	params.switch_timeout = le16_to_cpu(elems->ch_sw_timing->switch_timeout);
 
 	params.tmpl_skb =
 		ieee80211_tdls_ch_sw_resp_tmpl_get(sta, &params.ch_sw_tm_ie);
@@ -1763,6 +1767,7 @@
 out:
 	mutex_unlock(&local->sta_mtx);
 	dev_kfree_skb_any(params.tmpl_skb);
+	kfree(elems);
 	return ret;
 }
 
@@ -1771,7 +1776,7 @@
 					  struct sk_buff *skb)
 {
 	struct ieee80211_local *local = sdata->local;
-	struct ieee802_11_elems elems;
+	struct ieee802_11_elems *elems;
 	struct cfg80211_chan_def chandef;
 	struct ieee80211_channel *chan;
 	enum nl80211_channel_type chan_type;
@@ -1831,22 +1836,27 @@
 		return -EINVAL;
 	}
 
-	ieee802_11_parse_elems(tf->u.chan_switch_req.variable,
-			       skb->len - baselen, false, &elems, NULL, NULL);
-	if (elems.parse_error) {
+	elems = ieee802_11_parse_elems(tf->u.chan_switch_req.variable,
+				       skb->len - baselen, false, NULL, NULL);
+	if (!elems)
+		return -ENOMEM;
+
+	if (elems->parse_error) {
 		tdls_dbg(sdata, "Invalid IEs in TDLS channel switch req\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto free;
 	}
 
-	if (!elems.ch_sw_timing || !elems.lnk_id) {
+	if (!elems->ch_sw_timing || !elems->lnk_id) {
 		tdls_dbg(sdata, "TDLS channel switch req - missing IEs\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto free;
 	}
 
-	if (!elems.sec_chan_offs) {
+	if (!elems->sec_chan_offs) {
 		chan_type = NL80211_CHAN_HT20;
 	} else {
-		switch (elems.sec_chan_offs->sec_chan_offs) {
+		switch (elems->sec_chan_offs->sec_chan_offs) {
 		case IEEE80211_HT_PARAM_CHA_SEC_ABOVE:
 			chan_type = NL80211_CHAN_HT40PLUS;
 			break;
@@ -1865,7 +1875,8 @@
 	if (!cfg80211_reg_can_beacon_relax(sdata->local->hw.wiphy, &chandef,
 					   sdata->wdev.iftype)) {
 		tdls_dbg(sdata, "TDLS chan switch to forbidden channel\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto free;
 	}
 
 	mutex_lock(&local->sta_mtx);
@@ -1881,7 +1892,7 @@
 
 	/* validate the initiator is set correctly */
 	local_initiator =
-		!memcmp(elems.lnk_id->init_sta, sdata->vif.addr, ETH_ALEN);
+		!memcmp(elems->lnk_id->init_sta, sdata->vif.addr, ETH_ALEN);
 	if (local_initiator == sta->sta.tdls_initiator) {
 		tdls_dbg(sdata, "TDLS chan switch invalid lnk-id initiator\n");
 		ret = -EINVAL;
@@ -1889,16 +1900,16 @@
 	}
 
 	/* peer should have known better */
-	if (!sta->sta.ht_cap.ht_supported && elems.sec_chan_offs &&
-	    elems.sec_chan_offs->sec_chan_offs) {
+	if (!sta->sta.ht_cap.ht_supported && elems->sec_chan_offs &&
+	    elems->sec_chan_offs->sec_chan_offs) {
 		tdls_dbg(sdata, "TDLS chan switch - wide chan unsupported\n");
 		ret = -ENOTSUPP;
 		goto out;
 	}
 
 	params.chandef = &chandef;
-	params.switch_time = le16_to_cpu(elems.ch_sw_timing->switch_time);
-	params.switch_timeout = le16_to_cpu(elems.ch_sw_timing->switch_timeout);
+	params.switch_time = le16_to_cpu(elems->ch_sw_timing->switch_time);
+	params.switch_timeout = le16_to_cpu(elems->ch_sw_timing->switch_timeout);
 
 	params.tmpl_skb =
 		ieee80211_tdls_ch_sw_resp_tmpl_get(sta,
@@ -1917,6 +1928,8 @@
 out:
 	mutex_unlock(&local->sta_mtx);
 	dev_kfree_skb_any(params.tmpl_skb);
+free:
+	kfree(elems);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/trace.h
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/trace.h
@@ -67,7 +67,7 @@
 			__entry->min_freq_offset = (c)->chan ? (c)->chan->freq_offset : 0;	\
 			__entry->min_chan_width = (c)->width;				\
 			__entry->min_center_freq1 = (c)->center_freq1;			\
-			__entry->freq1_offset = (c)->freq1_offset;			\
+			__entry->min_freq1_offset = (c)->freq1_offset;			\
 			__entry->min_center_freq2 = (c)->center_freq2;
 #define MIN_CHANDEF_PR_FMT	" min_control:%d.%03d MHz min_width:%d min_center: %d.%03d/%d MHz"
 #define MIN_CHANDEF_PR_ARG	__entry->min_control_freq, __entry->min_freq_offset,	\
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/tx.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/tx.c
@@ -644,7 +644,8 @@
 		}
 
 		if (unlikely(tx->key && tx->key->flags & KEY_FLAG_TAINTED &&
-			     !ieee80211_is_deauth(hdr->frame_control)))
+			     !ieee80211_is_deauth(hdr->frame_control)) &&
+			     tx->skb->protocol != tx->sdata->control_port_protocol)
 			return TX_DROP;
 
 		if (!skip_hw && tx->key &&
@@ -1720,21 +1721,19 @@
  * Returns false if the frame couldn't be transmitted but was queued instead.
  */
 static bool __ieee80211_tx(struct ieee80211_local *local,
-			   struct sk_buff_head *skbs, int led_len,
-			   struct sta_info *sta, bool txpending)
+			   struct sk_buff_head *skbs, struct sta_info *sta,
+			   bool txpending)
 {
 	struct ieee80211_tx_info *info;
 	struct ieee80211_sub_if_data *sdata;
 	struct ieee80211_vif *vif;
 	struct sk_buff *skb;
 	bool result;
-	__le16 fc;
 
 	if (WARN_ON(skb_queue_empty(skbs)))
 		return true;
 
 	skb = skb_peek(skbs);
-	fc = ((struct ieee80211_hdr *)skb->data)->frame_control;
 	info = IEEE80211_SKB_CB(skb);
 	sdata = vif_to_sdata(info->control.vif);
 	if (sta && !sta->uploaded)
@@ -1768,8 +1767,6 @@
 
 	result = ieee80211_tx_frags(local, vif, sta, skbs, txpending);
 
-	ieee80211_tpt_led_trig_tx(local, fc, led_len);
-
 	WARN_ON_ONCE(!skb_queue_empty(skbs));
 
 	return result;
@@ -1825,15 +1822,15 @@
 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(tx->skb);
 	ieee80211_tx_result res = TX_CONTINUE;
 
+	if (!ieee80211_hw_check(&tx->local->hw, HAS_RATE_CONTROL))
+		CALL_TXH(ieee80211_tx_h_rate_ctrl);
+
 	if (unlikely(info->flags & IEEE80211_TX_INTFL_RETRANSMISSION)) {
 		__skb_queue_tail(&tx->skbs, tx->skb);
 		tx->skb = NULL;
 		goto txh_done;
 	}
 
-	if (!ieee80211_hw_check(&tx->local->hw, HAS_RATE_CONTROL))
-		CALL_TXH(ieee80211_tx_h_rate_ctrl);
-
 	CALL_TXH(ieee80211_tx_h_michael_mic_add);
 	CALL_TXH(ieee80211_tx_h_sequence);
 	CALL_TXH(ieee80211_tx_h_fragment);
@@ -1919,7 +1916,6 @@
 	ieee80211_tx_result res_prepare;
 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 	bool result = true;
-	int led_len;
 
 	if (unlikely(skb->len < 10)) {
 		dev_kfree_skb(skb);
@@ -1927,7 +1923,6 @@
 	}
 
 	/* initialises tx */
-	led_len = skb->len;
 	res_prepare = ieee80211_tx_prepare(sdata, &tx, sta, skb);
 
 	if (unlikely(res_prepare == TX_DROP)) {
@@ -1950,8 +1945,7 @@
 		return true;
 
 	if (!invoke_tx_handlers_late(&tx))
-		result = __ieee80211_tx(local, &tx.skbs, led_len,
-					tx.sta, txpending);
+		result = __ieee80211_tx(local, &tx.skbs, tx.sta, txpending);
 
 	return result;
 }
@@ -2971,7 +2965,7 @@
 	    sdata->vif.type == NL80211_IFTYPE_STATION)
 		goto out;
 
-	if (!test_sta_flag(sta, WLAN_STA_AUTHORIZED))
+	if (!test_sta_flag(sta, WLAN_STA_AUTHORIZED) || !sta->uploaded)
 		goto out;
 
 	if (test_sta_flag(sta, WLAN_STA_PS_STA) ||
@@ -3752,6 +3746,7 @@
 			goto begin;
 
 		skb = __skb_dequeue(&tx.skbs);
+		info = IEEE80211_SKB_CB(skb);
 
 		if (!skb_queue_empty(&tx.skbs)) {
 			spin_lock_bh(&fq->lock);
@@ -3796,7 +3791,7 @@
 	}
 
 encap_out:
-	IEEE80211_SKB_CB(skb)->control.vif = vif;
+	info->control.vif = vif;
 
 	if (vif &&
 	    wiphy_ext_feature_isset(local->hw.wiphy, NL80211_EXT_FEATURE_AQL)) {
@@ -4174,6 +4169,7 @@
 	struct ieee80211_local *local = sdata->local;
 	struct sta_info *sta;
 	struct sk_buff *next;
+	int len = skb->len;
 
 	if (unlikely(skb->len < ETH_HLEN)) {
 		kfree_skb(skb);
@@ -4220,10 +4216,8 @@
 		}
 	} else {
 		/* we cannot process non-linear frames on this path */
-		if (skb_linearize(skb)) {
-			kfree_skb(skb);
-			goto out;
-		}
+		if (skb_linearize(skb))
+			goto out_free;
 
 		/* the frame could be fragmented, software-encrypted, and other
 		 * things so we cannot really handle checksum offload with it -
@@ -4257,7 +4251,10 @@
 	goto out;
  out_free:
 	kfree_skb(skb);
+	len = 0;
  out:
+	if (len)
+		ieee80211_tpt_led_trig_tx(local, len);
 	rcu_read_unlock();
 }
 
@@ -4395,8 +4392,7 @@
 }
 
 static bool ieee80211_tx_8023(struct ieee80211_sub_if_data *sdata,
-			      struct sk_buff *skb, int led_len,
-			      struct sta_info *sta,
+			      struct sk_buff *skb, struct sta_info *sta,
 			      bool txpending)
 {
 	struct ieee80211_local *local = sdata->local;
@@ -4409,6 +4405,8 @@
 	if (sta)
 		sk_pacing_shift_update(skb->sk, local->hw.tx_sk_pacing_shift);
 
+	ieee80211_tpt_led_trig_tx(local, skb->len);
+
 	if (ieee80211_queue_skb(local, sdata, sta, skb))
 		return true;
 
@@ -4497,7 +4495,7 @@
 	if (key)
 		info->control.hw_key = &key->conf;
 
-	ieee80211_tx_8023(sdata, skb, skb->len, sta, false);
+	ieee80211_tx_8023(sdata, skb, sta, false);
 
 	return;
 
@@ -4636,7 +4634,7 @@
 		if (IS_ERR(sta) || (sta && !sta->uploaded))
 			sta = NULL;
 
-		result = ieee80211_tx_8023(sdata, skb, skb->len, sta, true);
+		result = ieee80211_tx_8023(sdata, skb, sta, true);
 	} else {
 		struct sk_buff_head skbs;
 
@@ -4646,7 +4644,7 @@
 		hdr = (struct ieee80211_hdr *)skb->data;
 		sta = sta_info_get(sdata, hdr->addr1);
 
-		result = __ieee80211_tx(local, &skbs, skb->len, sta, true);
+		result = __ieee80211_tx(local, &skbs, sta, true);
 	}
 
 	return result;
@@ -5723,6 +5721,9 @@
 	skb_reset_network_header(skb);
 	skb_reset_mac_header(skb);
 
+	if (local->hw.queues < IEEE80211_NUM_ACS)
+		goto start_xmit;
+
 	/* update QoS header to prioritize control port frames if possible,
 	 * priorization also happens for control port frames send over
 	 * AF_PACKET
@@ -5738,6 +5739,7 @@
 
 	rcu_read_unlock();
 
+start_xmit:
 	/* mutex lock is only needed for incrementing the cookie counter */
 	mutex_lock(&local->mtx);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/util.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/util.c
@@ -796,7 +796,7 @@
 
 	sdata = rcu_dereference_check(local->monitor_sdata,
 				      lockdep_is_held(&local->iflist_mtx) ||
-				      lockdep_rtnl_is_held());
+				      lockdep_is_held(&local->hw.wiphy->mtx));
 	if (sdata &&
 	    (iter_flags & IEEE80211_IFACE_ITER_RESUME_ALL || !active_only ||
 	     sdata->flags & IEEE80211_SDATA_IN_DRIVER))
@@ -943,7 +943,12 @@
 					      struct ieee802_11_elems *elems)
 {
 	const void *data = elem->data + 1;
-	u8 len = elem->datalen - 1;
+	u8 len;
+
+	if (!elem->datalen)
+		return;
+
+	len = elem->datalen - 1;
 
 	switch (elem->data[0]) {
 	case WLAN_EID_EXT_HE_MU_EDCA:
@@ -1112,10 +1117,6 @@
 			} else
 				elem_parse_failed = true;
 			break;
-		case WLAN_EID_CHALLENGE:
-			elems->challenge = pos;
-			elems->challenge_len = elen;
-			break;
 		case WLAN_EID_VENDOR_SPECIFIC:
 			if (elen >= 4 && pos[0] == 0x00 && pos[1] == 0x50 &&
 			    pos[2] == 0xf2) {
@@ -1395,8 +1396,8 @@
 
 static size_t ieee802_11_find_bssid_profile(const u8 *start, size_t len,
 					    struct ieee802_11_elems *elems,
-					    u8 *transmitter_bssid,
-					    u8 *bss_bssid,
+					    const u8 *transmitter_bssid,
+					    const u8 *bss_bssid,
 					    u8 *nontransmitted_profile)
 {
 	const struct element *elem, *sub;
@@ -1409,6 +1410,8 @@
 	for_each_element_id(elem, WLAN_EID_MULTIPLE_BSSID, start, len) {
 		if (elem->datalen < 2)
 			continue;
+		if (elem->data[0] < 1 || elem->data[0] > 8)
+			continue;
 
 		for_each_element(sub, elem->data + 1, elem->datalen - 1) {
 			u8 new_bssid[ETH_ALEN];
@@ -1461,31 +1464,38 @@
 	return found ? profile_len : 0;
 }
 
-u32 ieee802_11_parse_elems_crc(const u8 *start, size_t len, bool action,
-			       struct ieee802_11_elems *elems,
-			       u64 filter, u32 crc, u8 *transmitter_bssid,
-			       u8 *bss_bssid)
+struct ieee802_11_elems *ieee802_11_parse_elems_crc(const u8 *start, size_t len,
+						    bool action, u64 filter,
+						    u32 crc,
+						    const u8 *transmitter_bssid,
+						    const u8 *bss_bssid)
 {
+	struct ieee802_11_elems *elems;
 	const struct element *non_inherit = NULL;
 	u8 *nontransmitted_profile;
 	int nontransmitted_profile_len = 0;
+	size_t scratch_len = len;
 
-	memset(elems, 0, sizeof(*elems));
+	elems = kzalloc(sizeof(*elems) + scratch_len, GFP_ATOMIC);
+	if (!elems)
+		return NULL;
 	elems->ie_start = start;
 	elems->total_len = len;
+	elems->scratch_len = scratch_len;
+	elems->scratch_pos = elems->scratch;
 
-	nontransmitted_profile = kmalloc(len, GFP_ATOMIC);
-	if (nontransmitted_profile) {
-		nontransmitted_profile_len =
-			ieee802_11_find_bssid_profile(start, len, elems,
-						      transmitter_bssid,
-						      bss_bssid,
-						      nontransmitted_profile);
-		non_inherit =
-			cfg80211_find_ext_elem(WLAN_EID_EXT_NON_INHERITANCE,
-					       nontransmitted_profile,
-					       nontransmitted_profile_len);
-	}
+	nontransmitted_profile = elems->scratch_pos;
+	nontransmitted_profile_len =
+		ieee802_11_find_bssid_profile(start, len, elems,
+					      transmitter_bssid,
+					      bss_bssid,
+					      nontransmitted_profile);
+	elems->scratch_pos += nontransmitted_profile_len;
+	elems->scratch_len -= nontransmitted_profile_len;
+	non_inherit =
+		cfg80211_find_ext_elem(WLAN_EID_EXT_NON_INHERITANCE,
+				       nontransmitted_profile,
+				       nontransmitted_profile_len);
 
 	crc = _ieee802_11_parse_elems_crc(start, len, action, elems, filter,
 					  crc, non_inherit);
@@ -1514,9 +1524,9 @@
 	    offsetofend(struct ieee80211_bssid_index, dtim_count))
 		elems->dtim_count = elems->bssid_index->dtim_count;
 
-	kfree(nontransmitted_profile);
+	elems->crc = crc;
 
-	return crc;
+	return elems;
 }
 
 void ieee80211_regulatory_limit_wmm_params(struct ieee80211_sub_if_data *sdata,
@@ -1954,7 +1964,7 @@
 	if (he_cap &&
 	    cfg80211_any_usable_channels(local->hw.wiphy, BIT(sband->band),
 					 IEEE80211_CHAN_NO_HE)) {
-		pos = ieee80211_ie_build_he_cap(pos, he_cap, end);
+		pos = ieee80211_ie_build_he_cap(0, pos, he_cap, end);
 		if (!pos)
 			goto out_err;
 	}
@@ -2138,6 +2148,10 @@
 
 void ieee80211_stop_device(struct ieee80211_local *local)
 {
+	local_bh_disable();
+	ieee80211_handle_queued_frames(local);
+	local_bh_enable();
+
 	ieee80211_led_radio(local, false);
 	ieee80211_mod_tpt_led_trig(local, 0, IEEE80211_TPT_LEDTRIG_FL_RADIO);
 
@@ -2301,6 +2315,7 @@
 	struct cfg80211_sched_scan_request *sched_scan_req;
 	bool sched_scan_stopped = false;
 	bool suspended = local->suspended;
+	bool in_reconfig = false;
 
 	/* nothing to do if HW shouldn't run */
 	if (!local->open_count)
@@ -2361,6 +2376,9 @@
 			WARN(1, "Hardware became unavailable upon resume. This could be a software issue prior to suspend or a hardware issue.\n");
 		else
 			WARN(1, "Hardware became unavailable during restart.\n");
+		ieee80211_wake_queues_by_reason(hw, IEEE80211_MAX_QUEUE_MAP,
+						IEEE80211_QUEUE_STOP_REASON_SUSPEND,
+						false);
 		ieee80211_handle_reconfig_failure(local);
 		return res;
 	}
@@ -2379,7 +2397,7 @@
 				   IEEE80211_TPT_LEDTRIG_FL_RADIO, 0);
 
 	/* add interfaces */
-	sdata = rtnl_dereference(local->monitor_sdata);
+	sdata = wiphy_dereference(local->hw.wiphy, local->monitor_sdata);
 	if (sdata) {
 		/* in HW restart it exists already */
 		WARN_ON(local->resuming);
@@ -2424,7 +2442,8 @@
 				WARN_ON(drv_add_chanctx(local, ctx));
 		mutex_unlock(&local->chanctx_mtx);
 
-		sdata = rtnl_dereference(local->monitor_sdata);
+		sdata = wiphy_dereference(local->hw.wiphy,
+					  local->monitor_sdata);
 		if (sdata && ieee80211_sdata_running(sdata))
 			ieee80211_assign_chanctx(local, sdata);
 	}
@@ -2643,7 +2662,15 @@
 		mutex_unlock(&local->sta_mtx);
 	}
 
+	/*
+	 * If this is for hw restart things are still running.
+	 * We may want to change that later, however.
+	 */
+	if (local->open_count && (!suspended || reconfig_due_to_wowlan))
+		drv_reconfig_complete(local, IEEE80211_RECONFIG_TYPE_RESTART);
+
 	if (local->in_reconfig) {
+		in_reconfig = local->in_reconfig;
 		local->in_reconfig = false;
 		barrier();
 
@@ -2661,12 +2688,14 @@
 					IEEE80211_QUEUE_STOP_REASON_SUSPEND,
 					false);
 
-	/*
-	 * If this is for hw restart things are still running.
-	 * We may want to change that later, however.
-	 */
-	if (local->open_count && (!suspended || reconfig_due_to_wowlan))
-		drv_reconfig_complete(local, IEEE80211_RECONFIG_TYPE_RESTART);
+	if (in_reconfig) {
+		list_for_each_entry(sdata, &local->interfaces, list) {
+			if (!ieee80211_sdata_running(sdata))
+				continue;
+			if (sdata->vif.type == NL80211_IFTYPE_STATION)
+				ieee80211_sta_restart(sdata);
+		}
+	}
 
 	if (!suspended)
 		return 0;
@@ -2697,7 +2726,7 @@
 	return 0;
 }
 
-void ieee80211_resume_disconnect(struct ieee80211_vif *vif)
+static void ieee80211_reconfig_disconnect(struct ieee80211_vif *vif, u8 flag)
 {
 	struct ieee80211_sub_if_data *sdata;
 	struct ieee80211_local *local;
@@ -2709,19 +2738,35 @@
 	sdata = vif_to_sdata(vif);
 	local = sdata->local;
 
-	if (WARN_ON(!local->resuming))
+	if (WARN_ON(flag & IEEE80211_SDATA_DISCONNECT_RESUME &&
+		    !local->resuming))
+		return;
+
+	if (WARN_ON(flag & IEEE80211_SDATA_DISCONNECT_HW_RESTART &&
+		    !local->in_reconfig))
 		return;
 
 	if (WARN_ON(vif->type != NL80211_IFTYPE_STATION))
 		return;
 
-	sdata->flags |= IEEE80211_SDATA_DISCONNECT_RESUME;
+	sdata->flags |= flag;
 
 	mutex_lock(&local->key_mtx);
 	list_for_each_entry(key, &sdata->key_list, list)
 		key->flags |= KEY_FLAG_TAINTED;
 	mutex_unlock(&local->key_mtx);
 }
+
+void ieee80211_hw_restart_disconnect(struct ieee80211_vif *vif)
+{
+	ieee80211_reconfig_disconnect(vif, IEEE80211_SDATA_DISCONNECT_HW_RESTART);
+}
+EXPORT_SYMBOL_GPL(ieee80211_hw_restart_disconnect);
+
+void ieee80211_resume_disconnect(struct ieee80211_vif *vif)
+{
+	ieee80211_reconfig_disconnect(vif, IEEE80211_SDATA_DISCONNECT_RESUME);
+}
 EXPORT_SYMBOL_GPL(ieee80211_resume_disconnect);
 
 void ieee80211_recalc_smps(struct ieee80211_sub_if_data *sdata)
@@ -2897,10 +2942,11 @@
 				     he_cap->he_cap_elem.phy_cap_info);
 }
 
-u8 *ieee80211_ie_build_he_cap(u8 *pos,
+u8 *ieee80211_ie_build_he_cap(u32 disable_flags, u8 *pos,
 			      const struct ieee80211_sta_he_cap *he_cap,
 			      u8 *end)
 {
+	struct ieee80211_he_cap_elem elem;
 	u8 n;
 	u8 ie_len;
 	u8 *orig_pos = pos;
@@ -2913,7 +2959,23 @@
 	if (!he_cap)
 		return orig_pos;
 
-	n = ieee80211_he_mcs_nss_size(&he_cap->he_cap_elem);
+	/* modify on stack first to calculate 'n' and 'ie_len' correctly */
+	elem = he_cap->he_cap_elem;
+
+	if (disable_flags & IEEE80211_STA_DISABLE_40MHZ)
+		elem.phy_cap_info[0] &=
+			~(IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G |
+			  IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G);
+
+	if (disable_flags & IEEE80211_STA_DISABLE_160MHZ)
+		elem.phy_cap_info[0] &=
+			~IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G;
+
+	if (disable_flags & IEEE80211_STA_DISABLE_80P80MHZ)
+		elem.phy_cap_info[0] &=
+			~IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G;
+
+	n = ieee80211_he_mcs_nss_size(&elem);
 	ie_len = 2 + 1 +
 		 sizeof(he_cap->he_cap_elem) + n +
 		 ieee80211_he_ppe_size(he_cap->ppe_thres[0],
@@ -2927,8 +2989,8 @@
 	*pos++ = WLAN_EID_EXT_HE_CAPABILITY;
 
 	/* Fixed data */
-	memcpy(pos, &he_cap->he_cap_elem, sizeof(he_cap->he_cap_elem));
-	pos += sizeof(he_cap->he_cap_elem);
+	memcpy(pos, &elem, sizeof(elem));
+	pos += sizeof(elem);
 
 	memcpy(pos, &he_cap->he_mcs_nss_supp, n);
 	pos += n;
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac80211/wme.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac80211/wme.c
@@ -143,20 +143,21 @@
 u16 __ieee80211_select_queue(struct ieee80211_sub_if_data *sdata,
 			     struct sta_info *sta, struct sk_buff *skb)
 {
-	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+	const struct ethhdr *eth = (void *)skb->data;
 	struct mac80211_qos_map *qos_map;
 	bool qos;
 
 	/* all mesh/ocb stations are required to support WME */
-	if (sdata->vif.type == NL80211_IFTYPE_MESH_POINT ||
-	    sdata->vif.type == NL80211_IFTYPE_OCB)
+	if ((sdata->vif.type == NL80211_IFTYPE_MESH_POINT &&
+	    !is_multicast_ether_addr(eth->h_dest)) ||
+	    (sdata->vif.type == NL80211_IFTYPE_OCB && sta))
 		qos = true;
 	else if (sta)
 		qos = sta->sta.wme;
 	else
 		qos = false;
 
-	if (!qos || (info->control.flags & IEEE80211_TX_CTRL_DONT_REORDER)) {
+	if (!qos) {
 		skb->priority = 0; /* required for correct WPA/11i MIC */
 		return IEEE80211_AC_BE;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac802154/iface.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac802154/iface.c
@@ -661,6 +661,7 @@
 	sdata->dev = ndev;
 	sdata->wpan_dev.wpan_phy = local->hw.phy;
 	sdata->local = local;
+	INIT_LIST_HEAD(&sdata->wpan_dev.list);
 
 	/* setup type-dependent data */
 	ret = ieee802154_setup_sdata(sdata, type);
@@ -687,6 +688,10 @@
 	ASSERT_RTNL();
 
 	mutex_lock(&sdata->local->iflist_mtx);
+	if (list_empty(&sdata->local->interfaces)) {
+		mutex_unlock(&sdata->local->iflist_mtx);
+		return;
+	}
 	list_del_rcu(&sdata->list);
 	mutex_unlock(&sdata->local->iflist_mtx);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac802154/llsec.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac802154/llsec.c
@@ -265,19 +265,27 @@
 	return -ENOMEM;
 }
 
+static void mac802154_llsec_key_del_rcu(struct rcu_head *rcu)
+{
+	struct ieee802154_llsec_key_entry *pos;
+	struct mac802154_llsec_key *mkey;
+
+	pos = container_of(rcu, struct ieee802154_llsec_key_entry, rcu);
+	mkey = container_of(pos->key, struct mac802154_llsec_key, key);
+
+	llsec_key_put(mkey);
+	kfree_sensitive(pos);
+}
+
 int mac802154_llsec_key_del(struct mac802154_llsec *sec,
 			    const struct ieee802154_llsec_key_id *key)
 {
 	struct ieee802154_llsec_key_entry *pos;
 
 	list_for_each_entry(pos, &sec->table.keys, list) {
-		struct mac802154_llsec_key *mkey;
-
-		mkey = container_of(pos->key, struct mac802154_llsec_key, key);
-
 		if (llsec_key_id_equal(&pos->id, key)) {
 			list_del_rcu(&pos->list);
-			llsec_key_put(mkey);
+			call_rcu(&pos->rcu, mac802154_llsec_key_del_rcu);
 			return 0;
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac802154/rx.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac802154/rx.c
@@ -44,7 +44,7 @@
 
 	switch (mac_cb(skb)->dest.mode) {
 	case IEEE802154_ADDR_NONE:
-		if (mac_cb(skb)->dest.mode != IEEE802154_ADDR_NONE)
+		if (hdr->source.mode != IEEE802154_ADDR_NONE)
 			/* FIXME: check if we are PAN coordinator */
 			skb->pkt_type = PACKET_OTHERHOST;
 		else
@@ -132,7 +132,7 @@
 ieee802154_parse_frame_start(struct sk_buff *skb, struct ieee802154_hdr *hdr)
 {
 	int hlen;
-	struct ieee802154_mac_cb *cb = mac_cb_init(skb);
+	struct ieee802154_mac_cb *cb = mac_cb(skb);
 
 	skb_reset_mac_header(skb);
 
@@ -294,8 +294,9 @@
 ieee802154_rx_irqsafe(struct ieee802154_hw *hw, struct sk_buff *skb, u8 lqi)
 {
 	struct ieee802154_local *local = hw_to_local(hw);
+	struct ieee802154_mac_cb *cb = mac_cb_init(skb);
 
-	mac_cb(skb)->lqi = lqi;
+	cb->lqi = lqi;
 	skb->pkt_type = IEEE802154_RX_MSG;
 	skb_queue_tail(&local->skb_queue, skb);
 	tasklet_schedule(&local->tasklet);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mac802154/tx.c
+++ linux-xilinx-zynqmp-5.15.0/net/mac802154/tx.c
@@ -34,8 +34,8 @@
 	if (res)
 		goto err_tx;
 
-	dev->stats.tx_packets++;
-	dev->stats.tx_bytes += skb->len;
+	DEV_STATS_INC(dev, tx_packets);
+	DEV_STATS_ADD(dev, tx_bytes, skb->len);
 
 	ieee802154_xmit_complete(&local->hw, skb, false);
 
@@ -86,8 +86,8 @@
 			goto err_tx;
 		}
 
-		dev->stats.tx_packets++;
-		dev->stats.tx_bytes += len;
+		DEV_STATS_INC(dev, tx_packets);
+		DEV_STATS_ADD(dev, tx_bytes, len);
 	} else {
 		local->tx_skb = skb;
 		queue_work(local->workqueue, &local->tx_work);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mctp/af_mctp.c
+++ linux-xilinx-zynqmp-5.15.0/net/mctp/af_mctp.c
@@ -30,6 +30,12 @@
 	return 0;
 }
 
+/* Generic sockaddr checks, padding checks only so far */
+static bool mctp_sockaddr_is_ok(const struct sockaddr_mctp *addr)
+{
+	return !addr->__smctp_pad0 && !addr->__smctp_pad1;
+}
+
 static int mctp_bind(struct socket *sock, struct sockaddr *addr, int addrlen)
 {
 	struct sock *sk = sock->sk;
@@ -49,6 +55,9 @@
 	/* it's a valid sockaddr for MCTP, cast and do protocol checks */
 	smctp = (struct sockaddr_mctp *)addr;
 
+	if (!mctp_sockaddr_is_ok(smctp))
+		return -EINVAL;
+
 	lock_sock(sk);
 
 	/* TODO: allow rebind */
@@ -83,6 +92,8 @@
 			return -EINVAL;
 		if (addr->smctp_family != AF_MCTP)
 			return -EINVAL;
+		if (!mctp_sockaddr_is_ok(addr))
+			return -EINVAL;
 		if (addr->smctp_tag & ~(MCTP_TAG_MASK | MCTP_TAG_OWNER))
 			return -EINVAL;
 
@@ -172,11 +183,13 @@
 
 		addr = msg->msg_name;
 		addr->smctp_family = AF_MCTP;
+		addr->__smctp_pad0 = 0;
 		addr->smctp_network = cb->net;
 		addr->smctp_addr.s_addr = hdr->src;
 		addr->smctp_type = type;
 		addr->smctp_tag = hdr->flags_seq_tag &
 					(MCTP_HDR_TAG_MASK | MCTP_HDR_FLAG_TO);
+		addr->__smctp_pad1 = 0;
 		msg->msg_namelen = sizeof(*addr);
 	}
 
@@ -275,11 +288,17 @@
 
 		kfree_rcu(key, rcu);
 	}
+	sock_set_flag(sk, SOCK_DEAD);
 	spin_unlock_irqrestore(&net->mctp.keys_lock, flags);
 
 	synchronize_rcu();
 }
 
+static void mctp_sk_destruct(struct sock *sk)
+{
+	skb_queue_purge(&sk->sk_receive_queue);
+}
+
 static struct proto mctp_proto = {
 	.name		= "MCTP",
 	.owner		= THIS_MODULE,
@@ -316,6 +335,7 @@
 		return -ENOMEM;
 
 	sock_init_data(sock, sk);
+	sk->sk_destruct = mctp_sk_destruct;
 
 	rc = 0;
 	if (sk->sk_prot->init)
@@ -362,12 +382,18 @@
 
 	rc = mctp_neigh_init();
 	if (rc)
-		goto err_unreg_proto;
+		goto err_unreg_routes;
 
-	mctp_device_init();
+	rc = mctp_device_init();
+	if (rc)
+		goto err_unreg_neigh;
 
 	return 0;
 
+err_unreg_neigh:
+	mctp_neigh_exit();
+err_unreg_routes:
+	mctp_routes_exit();
 err_unreg_proto:
 	proto_unregister(&mctp_proto);
 err_unreg_sock:
--- linux-xilinx-zynqmp-5.15.0.orig/net/mctp/device.c
+++ linux-xilinx-zynqmp-5.15.0/net/mctp/device.c
@@ -24,25 +24,30 @@
 	size_t a_idx;
 };
 
-/* unlocked: caller must hold rcu_read_lock */
+/* unlocked: caller must hold rcu_read_lock.
+ * Returned mctp_dev has its refcount incremented, or NULL if unset.
+ */
 struct mctp_dev *__mctp_dev_get(const struct net_device *dev)
 {
-	return rcu_dereference(dev->mctp_ptr);
+	struct mctp_dev *mdev = rcu_dereference(dev->mctp_ptr);
+
+	/* RCU guarantees that any mdev is still live.
+	 * Zero refcount implies a pending free, return NULL.
+	 */
+	if (mdev)
+		if (!refcount_inc_not_zero(&mdev->refs))
+			return NULL;
+	return mdev;
 }
 
+/* Returned mctp_dev does not have refcount incremented. The returned pointer
+ * remains live while rtnl_lock is held, as that prevents mctp_unregister()
+ */
 struct mctp_dev *mctp_dev_get_rtnl(const struct net_device *dev)
 {
 	return rtnl_dereference(dev->mctp_ptr);
 }
 
-static void mctp_dev_destroy(struct mctp_dev *mdev)
-{
-	struct net_device *dev = mdev->dev;
-
-	dev_put(dev);
-	kfree_rcu(mdev, rcu);
-}
-
 static int mctp_fill_addrinfo(struct sk_buff *skb, struct netlink_callback *cb,
 			      struct mctp_dev *mdev, mctp_eid_t eid)
 {
@@ -117,6 +122,7 @@
 				if (mdev) {
 					rc = mctp_dump_dev_addrinfo(mdev,
 								    skb, cb);
+					mctp_dev_put(mdev);
 					// Error indicates full buffer, this
 					// callback will get retried.
 					if (rc < 0)
@@ -255,6 +261,20 @@
 	return 0;
 }
 
+void mctp_dev_hold(struct mctp_dev *mdev)
+{
+	refcount_inc(&mdev->refs);
+}
+
+void mctp_dev_put(struct mctp_dev *mdev)
+{
+	if (mdev && refcount_dec_and_test(&mdev->refs)) {
+		kfree(mdev->addrs);
+		dev_put(mdev->dev);
+		kfree_rcu(mdev, rcu);
+	}
+}
+
 static struct mctp_dev *mctp_add_dev(struct net_device *dev)
 {
 	struct mctp_dev *mdev;
@@ -270,7 +290,9 @@
 	mdev->net = mctp_default_net(dev_net(dev));
 
 	/* associate to net_device */
+	refcount_set(&mdev->refs, 1);
 	rcu_assign_pointer(dev->mctp_ptr, mdev);
+
 	dev_hold(dev);
 	mdev->dev = dev;
 
@@ -301,6 +323,7 @@
 	if (!mdev)
 		return 0;
 	ret = nla_total_size(4); /* IFLA_MCTP_NET */
+	mctp_dev_put(mdev);
 	return ret;
 }
 
@@ -343,9 +366,8 @@
 
 	mctp_route_remove_dev(mdev);
 	mctp_neigh_remove_dev(mdev);
-	kfree(mdev->addrs);
 
-	mctp_dev_destroy(mdev);
+	mctp_dev_put(mdev);
 }
 
 static int mctp_register(struct net_device *dev)
@@ -356,9 +378,12 @@
 	if (rtnl_dereference(dev->mctp_ptr))
 		return 0;
 
-	/* only register specific types; MCTP-specific and loopback for now */
-	if (dev->type != ARPHRD_MCTP && dev->type != ARPHRD_LOOPBACK)
+	/* only register specific types (inc. NONE for TUN devices) */
+	if (!(dev->type == ARPHRD_MCTP ||
+	      dev->type == ARPHRD_LOOPBACK ||
+	      dev->type == ARPHRD_NONE)) {
 		return 0;
+	}
 
 	mdev = mctp_add_dev(dev);
 	if (IS_ERR(mdev))
@@ -399,25 +424,31 @@
 	.priority = ADDRCONF_NOTIFY_PRIORITY,
 };
 
-void __init mctp_device_init(void)
+static const struct rtnl_msg_handler mctp_device_rtnl_msg_handlers[] = {
+	{THIS_MODULE, PF_MCTP, RTM_NEWADDR, mctp_rtm_newaddr, NULL, 0},
+	{THIS_MODULE, PF_MCTP, RTM_DELADDR, mctp_rtm_deladdr, NULL, 0},
+	{THIS_MODULE, PF_MCTP, RTM_GETADDR, NULL, mctp_dump_addrinfo, 0},
+};
+
+int __init mctp_device_init(void)
 {
-	register_netdevice_notifier(&mctp_dev_nb);
+	int err;
 
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_GETADDR,
-			     NULL, mctp_dump_addrinfo, 0);
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_NEWADDR,
-			     mctp_rtm_newaddr, NULL, 0);
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_DELADDR,
-			     mctp_rtm_deladdr, NULL, 0);
+	register_netdevice_notifier(&mctp_dev_nb);
 	rtnl_af_register(&mctp_af_ops);
+
+	err = rtnl_register_many(mctp_device_rtnl_msg_handlers);
+	if (err) {
+		rtnl_af_unregister(&mctp_af_ops);
+		unregister_netdevice_notifier(&mctp_dev_nb);
+	}
+
+	return err;
 }
 
 void __exit mctp_device_exit(void)
 {
+	rtnl_unregister_many(mctp_device_rtnl_msg_handlers);
 	rtnl_af_unregister(&mctp_af_ops);
-	rtnl_unregister(PF_MCTP, RTM_DELADDR);
-	rtnl_unregister(PF_MCTP, RTM_NEWADDR);
-	rtnl_unregister(PF_MCTP, RTM_GETADDR);
-
 	unregister_netdevice_notifier(&mctp_dev_nb);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mctp/neigh.c
+++ linux-xilinx-zynqmp-5.15.0/net/mctp/neigh.c
@@ -47,7 +47,7 @@
 	}
 	INIT_LIST_HEAD(&neigh->list);
 	neigh->dev = mdev;
-	dev_hold(neigh->dev->dev);
+	mctp_dev_hold(neigh->dev);
 	neigh->eid = eid;
 	neigh->source = source;
 	memcpy(neigh->ha, lladdr, lladdr_len);
@@ -63,7 +63,7 @@
 {
 	struct mctp_neigh *neigh = container_of(rcu, struct mctp_neigh, rcu);
 
-	dev_put(neigh->dev->dev);
+	mctp_dev_put(neigh->dev);
 	kfree(neigh);
 }
 
@@ -321,22 +321,29 @@
 	.exit = mctp_neigh_net_exit,
 };
 
+static const struct rtnl_msg_handler mctp_neigh_rtnl_msg_handlers[] = {
+	{THIS_MODULE, PF_MCTP, RTM_NEWNEIGH, mctp_rtm_newneigh, NULL, 0},
+	{THIS_MODULE, PF_MCTP, RTM_DELNEIGH, mctp_rtm_delneigh, NULL, 0},
+	{THIS_MODULE, PF_MCTP, RTM_GETNEIGH, NULL, mctp_rtm_getneigh, 0},
+};
+
 int __init mctp_neigh_init(void)
 {
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_NEWNEIGH,
-			     mctp_rtm_newneigh, NULL, 0);
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_DELNEIGH,
-			     mctp_rtm_delneigh, NULL, 0);
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_GETNEIGH,
-			     NULL, mctp_rtm_getneigh, 0);
+	int err;
+
+	err = register_pernet_subsys(&mctp_net_ops);
+	if (err)
+		return err;
+
+	err = rtnl_register_many(mctp_neigh_rtnl_msg_handlers);
+	if (err)
+		unregister_pernet_subsys(&mctp_net_ops);
 
-	return register_pernet_subsys(&mctp_net_ops);
+	return err;
 }
 
-void __exit mctp_neigh_exit(void)
+void mctp_neigh_exit(void)
 {
+	rtnl_unregister_many(mctp_neigh_rtnl_msg_handlers);
 	unregister_pernet_subsys(&mctp_net_ops);
-	rtnl_unregister(PF_MCTP, RTM_GETNEIGH);
-	rtnl_unregister(PF_MCTP, RTM_DELNEIGH);
-	rtnl_unregister(PF_MCTP, RTM_NEWNEIGH);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mctp/route.c
+++ linux-xilinx-zynqmp-5.15.0/net/mctp/route.c
@@ -135,6 +135,11 @@
 
 	spin_lock_irqsave(&net->mctp.keys_lock, flags);
 
+	if (sock_flag(&msk->sk, SOCK_DEAD)) {
+		rc = -EINVAL;
+		goto out_unlock;
+	}
+
 	hlist_for_each_entry(tmp, &net->mctp.keys, hlist) {
 		if (mctp_key_match(tmp, key->local_addr, key->peer_addr,
 				   key->tag)) {
@@ -148,6 +153,7 @@
 		hlist_add_head(&key->sklist, &msk->keys);
 	}
 
+out_unlock:
 	spin_unlock_irqrestore(&net->mctp.keys_lock, flags);
 
 	return rc;
@@ -396,7 +402,7 @@
 
 	rc = dev_hard_header(skb, skb->dev, ntohs(skb->protocol),
 			     daddr, skb->dev->dev_addr, skb->len);
-	if (rc) {
+	if (rc < 0) {
 		kfree_skb(skb);
 		return -EHOSTUNREACH;
 	}
@@ -412,7 +418,7 @@
 static void mctp_route_release(struct mctp_route *rt)
 {
 	if (refcount_dec_and_test(&rt->refs)) {
-		dev_put(rt->dev->dev);
+		mctp_dev_put(rt->dev);
 		kfree_rcu(rt, rcu);
 	}
 }
@@ -474,6 +480,10 @@
 	int rc = -EAGAIN;
 	u8 tagbits;
 
+	/* for NULL destination EIDs, we may get a response from any peer */
+	if (daddr == MCTP_ADDR_NULL)
+		daddr = MCTP_ADDR_ANY;
+
 	/* be optimistic, alloc now */
 	key = mctp_key_alloc(msk, saddr, daddr, 0, GFP_KERNEL);
 	if (!key)
@@ -539,6 +549,8 @@
 {
 	struct mctp_route *tmp, *rt = NULL;
 
+	rcu_read_lock();
+
 	list_for_each_entry_rcu(tmp, &net->mctp.routes, list) {
 		/* TODO: add metrics */
 		if (mctp_rt_match_eid(tmp, dnet, daddr)) {
@@ -549,6 +561,28 @@
 		}
 	}
 
+	rcu_read_unlock();
+
+	return rt;
+}
+
+static struct mctp_route *mctp_route_lookup_null(struct net *net,
+						 struct net_device *dev)
+{
+	struct mctp_route *tmp, *rt = NULL;
+
+	rcu_read_lock();
+
+	list_for_each_entry_rcu(tmp, &net->mctp.routes, list) {
+		if (tmp->dev->dev == dev && tmp->type == RTN_LOCAL &&
+		    refcount_inc_not_zero(&tmp->refs)) {
+			rt = tmp;
+			break;
+		}
+	}
+
+	rcu_read_unlock();
+
 	return rt;
 }
 
@@ -741,7 +775,7 @@
 	rt->max = daddr_start + daddr_extent;
 	rt->mtu = mtu;
 	rt->dev = mdev;
-	dev_hold(rt->dev->dev);
+	mctp_dev_hold(rt->dev);
 	rt->type = type;
 	rt->output = rtfn;
 
@@ -760,7 +794,7 @@
 }
 
 static int mctp_route_remove(struct mctp_dev *mdev, mctp_eid_t daddr_start,
-			     unsigned int daddr_extent)
+			     unsigned int daddr_extent, unsigned char type)
 {
 	struct net *net = dev_net(mdev->dev);
 	struct mctp_route *rt, *tmp;
@@ -777,7 +811,8 @@
 
 	list_for_each_entry_safe(rt, tmp, &net->mctp.routes, list) {
 		if (rt->dev == mdev &&
-		    rt->min == daddr_start && rt->max == daddr_end) {
+		    rt->min == daddr_start && rt->max == daddr_end &&
+		    rt->type == type) {
 			list_del_rcu(&rt->list);
 			/* TODO: immediate RTM_DELROUTE */
 			mctp_route_release(rt);
@@ -795,7 +830,7 @@
 
 int mctp_route_remove_local(struct mctp_dev *mdev, mctp_eid_t addr)
 {
-	return mctp_route_remove(mdev, addr, 0);
+	return mctp_route_remove(mdev, addr, 0, RTN_LOCAL);
 }
 
 /* removes all entries for a given device */
@@ -821,13 +856,18 @@
 				struct net_device *orig_dev)
 {
 	struct net *net = dev_net(dev);
+	struct mctp_dev *mdev;
 	struct mctp_skb_cb *cb;
 	struct mctp_route *rt;
 	struct mctp_hdr *mh;
 
-	/* basic non-data sanity checks */
-	if (dev->type != ARPHRD_MCTP)
+	rcu_read_lock();
+	mdev = __mctp_dev_get(dev);
+	rcu_read_unlock();
+	if (!mdev) {
+		/* basic non-data sanity checks */
 		goto err_drop;
+	}
 
 	if (!pskb_may_pull(skb, sizeof(struct mctp_hdr)))
 		goto err_drop;
@@ -841,20 +881,25 @@
 		goto err_drop;
 
 	cb = __mctp_cb(skb);
-	rcu_read_lock();
-	cb->net = READ_ONCE(__mctp_dev_get(dev)->net);
-	rcu_read_unlock();
+	cb->net = READ_ONCE(mdev->net);
 
 	rt = mctp_route_lookup(net, cb->net, mh->dest);
+
+	/* NULL EID, but addressed to our physical address */
+	if (!rt && mh->dest == MCTP_ADDR_NULL && skb->pkt_type == PACKET_HOST)
+		rt = mctp_route_lookup_null(net, dev);
+
 	if (!rt)
 		goto err_drop;
 
 	mctp_do_route(rt, skb);
+	mctp_dev_put(mdev);
 
 	return NET_RX_SUCCESS;
 
 err_drop:
 	kfree_skb(skb);
+	mctp_dev_put(mdev);
 	return NET_RX_DROP;
 }
 
@@ -975,7 +1020,7 @@
 	if (rtm->rtm_type != RTN_UNICAST)
 		return -EINVAL;
 
-	rc = mctp_route_remove(mdev, daddr_start, rtm->rtm_dst_len);
+	rc = mctp_route_remove(mdev, daddr_start, rtm->rtm_dst_len, RTN_UNICAST);
 	return rc;
 }
 
@@ -1094,25 +1139,38 @@
 	.exit = mctp_routes_net_exit,
 };
 
+static const struct rtnl_msg_handler mctp_route_rtnl_msg_handlers[] = {
+	{THIS_MODULE, PF_MCTP, RTM_NEWROUTE, mctp_newroute, NULL, 0},
+	{THIS_MODULE, PF_MCTP, RTM_DELROUTE, mctp_delroute, NULL, 0},
+	{THIS_MODULE, PF_MCTP, RTM_GETROUTE, NULL, mctp_dump_rtinfo, 0},
+};
+
 int __init mctp_routes_init(void)
 {
+	int err;
+
 	dev_add_pack(&mctp_packet_type);
 
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_GETROUTE,
-			     NULL, mctp_dump_rtinfo, 0);
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_NEWROUTE,
-			     mctp_newroute, NULL, 0);
-	rtnl_register_module(THIS_MODULE, PF_MCTP, RTM_DELROUTE,
-			     mctp_delroute, NULL, 0);
+	err = register_pernet_subsys(&mctp_net_ops);
+	if (err)
+		goto err_pernet;
+
+	err = rtnl_register_many(mctp_route_rtnl_msg_handlers);
+	if (err)
+		goto err_rtnl;
 
-	return register_pernet_subsys(&mctp_net_ops);
+	return 0;
+
+err_rtnl:
+	unregister_pernet_subsys(&mctp_net_ops);
+err_pernet:
+	dev_remove_pack(&mctp_packet_type);
+	return err;
 }
 
-void __exit mctp_routes_exit(void)
+void mctp_routes_exit(void)
 {
+	rtnl_unregister_many(mctp_route_rtnl_msg_handlers);
 	unregister_pernet_subsys(&mctp_net_ops);
-	rtnl_unregister(PF_MCTP, RTM_DELROUTE);
-	rtnl_unregister(PF_MCTP, RTM_NEWROUTE);
-	rtnl_unregister(PF_MCTP, RTM_GETROUTE);
 	dev_remove_pack(&mctp_packet_type);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/mpls/af_mpls.c
+++ linux-xilinx-zynqmp-5.15.0/net/mpls/af_mpls.c
@@ -1079,9 +1079,9 @@
 
 		p = per_cpu_ptr(mdev->stats, i);
 		do {
-			start = u64_stats_fetch_begin(&p->syncp);
+			start = u64_stats_fetch_begin_irq(&p->syncp);
 			local = p->stats;
-		} while (u64_stats_fetch_retry(&p->syncp, start));
+		} while (u64_stats_fetch_retry_irq(&p->syncp, start));
 
 		stats->rx_packets	+= local.rx_packets;
 		stats->rx_bytes		+= local.rx_bytes;
@@ -1428,6 +1428,7 @@
 free:
 	kfree(table);
 out:
+	mdev->sysctl = NULL;
 	return -ENOBUFS;
 }
 
@@ -1437,6 +1438,9 @@
 	struct net *net = dev_net(dev);
 	struct ctl_table *table;
 
+	if (!mdev->sysctl)
+		return;
+
 	table = mdev->sysctl->ctl_table_arg;
 	unregister_net_sysctl_table(mdev->sysctl);
 	kfree(table);
@@ -1491,22 +1495,52 @@
 	kfree(mdev);
 }
 
-static void mpls_ifdown(struct net_device *dev, int event)
+static int mpls_ifdown(struct net_device *dev, int event)
 {
 	struct mpls_route __rcu **platform_label;
 	struct net *net = dev_net(dev);
-	u8 alive, deleted;
 	unsigned index;
 
 	platform_label = rtnl_dereference(net->mpls.platform_label);
 	for (index = 0; index < net->mpls.platform_labels; index++) {
 		struct mpls_route *rt = rtnl_dereference(platform_label[index]);
+		bool nh_del = false;
+		u8 alive = 0;
 
 		if (!rt)
 			continue;
 
-		alive = 0;
-		deleted = 0;
+		if (event == NETDEV_UNREGISTER) {
+			u8 deleted = 0;
+
+			for_nexthops(rt) {
+				struct net_device *nh_dev =
+					rtnl_dereference(nh->nh_dev);
+
+				if (!nh_dev || nh_dev == dev)
+					deleted++;
+				if (nh_dev == dev)
+					nh_del = true;
+			} endfor_nexthops(rt);
+
+			/* if there are no more nexthops, delete the route */
+			if (deleted == rt->rt_nhn) {
+				mpls_route_update(net, index, NULL, NULL);
+				continue;
+			}
+
+			if (nh_del) {
+				size_t size = sizeof(*rt) + rt->rt_nhn *
+					rt->rt_nh_size;
+				struct mpls_route *orig = rt;
+
+				rt = kmalloc(size, GFP_KERNEL);
+				if (!rt)
+					return -ENOMEM;
+				memcpy(rt, orig, size);
+			}
+		}
+
 		change_nexthops(rt) {
 			unsigned int nh_flags = nh->nh_flags;
 
@@ -1530,16 +1564,15 @@
 next:
 			if (!(nh_flags & (RTNH_F_DEAD | RTNH_F_LINKDOWN)))
 				alive++;
-			if (!rtnl_dereference(nh->nh_dev))
-				deleted++;
 		} endfor_nexthops(rt);
 
 		WRITE_ONCE(rt->rt_nhn_alive, alive);
 
-		/* if there are no more nexthops, delete the route */
-		if (event == NETDEV_UNREGISTER && deleted == rt->rt_nhn)
-			mpls_route_update(net, index, NULL, NULL);
+		if (nh_del)
+			mpls_route_update(net, index, rt, NULL);
 	}
+
+	return 0;
 }
 
 static void mpls_ifup(struct net_device *dev, unsigned int flags)
@@ -1597,8 +1630,12 @@
 		return NOTIFY_OK;
 
 	switch (event) {
+		int err;
+
 	case NETDEV_DOWN:
-		mpls_ifdown(dev, event);
+		err = mpls_ifdown(dev, event);
+		if (err)
+			return notifier_from_errno(err);
 		break;
 	case NETDEV_UP:
 		flags = dev_get_flags(dev);
@@ -1609,13 +1646,18 @@
 		break;
 	case NETDEV_CHANGE:
 		flags = dev_get_flags(dev);
-		if (flags & (IFF_RUNNING | IFF_LOWER_UP))
+		if (flags & (IFF_RUNNING | IFF_LOWER_UP)) {
 			mpls_ifup(dev, RTNH_F_DEAD | RTNH_F_LINKDOWN);
-		else
-			mpls_ifdown(dev, event);
+		} else {
+			err = mpls_ifdown(dev, event);
+			if (err)
+				return notifier_from_errno(err);
+		}
 		break;
 	case NETDEV_UNREGISTER:
-		mpls_ifdown(dev, event);
+		err = mpls_ifdown(dev, event);
+		if (err)
+			return notifier_from_errno(err);
 		mdev = mpls_dev_get(dev);
 		if (mdev) {
 			mpls_dev_sysctl_unregister(dev, mdev);
@@ -1626,8 +1668,6 @@
 	case NETDEV_CHANGENAME:
 		mdev = mpls_dev_get(dev);
 		if (mdev) {
-			int err;
-
 			mpls_dev_sysctl_unregister(dev, mdev);
 			err = mpls_dev_sysctl_register(dev, mdev);
 			if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/diag.c
@@ -13,17 +13,22 @@
 #include <uapi/linux/mptcp.h>
 #include "protocol.h"
 
-static int subflow_get_info(const struct sock *sk, struct sk_buff *skb)
+static int subflow_get_info(struct sock *sk, struct sk_buff *skb)
 {
 	struct mptcp_subflow_context *sf;
 	struct nlattr *start;
 	u32 flags = 0;
+	bool slow;
 	int err;
 
+	if (inet_sk_state_load(sk) == TCP_LISTEN)
+		return 0;
+
 	start = nla_nest_start_noflag(skb, INET_ULP_INFO_MPTCP);
 	if (!start)
 		return -EMSGSIZE;
 
+	slow = lock_sock_fast(sk);
 	rcu_read_lock();
 	sf = rcu_dereference(inet_csk(sk)->icsk_ulp_data);
 	if (!sf) {
@@ -69,11 +74,13 @@
 	}
 
 	rcu_read_unlock();
+	unlock_sock_fast(sk, slow);
 	nla_nest_end(skb, start);
 	return 0;
 
 nla_failure:
 	rcu_read_unlock();
+	unlock_sock_fast(sk, slow);
 	nla_nest_cancel(skb, start);
 	return err;
 }
@@ -88,7 +95,7 @@
 		nla_total_size(4) +	/* MPTCP_SUBFLOW_ATTR_RELWRITE_SEQ */
 		nla_total_size_64bit(8) +	/* MPTCP_SUBFLOW_ATTR_MAP_SEQ */
 		nla_total_size(4) +	/* MPTCP_SUBFLOW_ATTR_MAP_SFSEQ */
-		nla_total_size(2) +	/* MPTCP_SUBFLOW_ATTR_SSN_OFFSET */
+		nla_total_size(4) +	/* MPTCP_SUBFLOW_ATTR_SSN_OFFSET */
 		nla_total_size(2) +	/* MPTCP_SUBFLOW_ATTR_MAP_DATALEN */
 		nla_total_size(4) +	/* MPTCP_SUBFLOW_ATTR_FLAGS */
 		nla_total_size(1) +	/* MPTCP_SUBFLOW_ATTR_ID_REM */
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/mib.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/mib.c
@@ -15,15 +15,20 @@
 	SNMP_MIB_ITEM("MPCapableACKRX", MPTCP_MIB_MPCAPABLEPASSIVEACK),
 	SNMP_MIB_ITEM("MPCapableFallbackACK", MPTCP_MIB_MPCAPABLEPASSIVEFALLBACK),
 	SNMP_MIB_ITEM("MPCapableFallbackSYNACK", MPTCP_MIB_MPCAPABLEACTIVEFALLBACK),
+	SNMP_MIB_ITEM("MPCapableEndpAttempt", MPTCP_MIB_MPCAPABLEENDPATTEMPT),
 	SNMP_MIB_ITEM("MPFallbackTokenInit", MPTCP_MIB_TOKENFALLBACKINIT),
 	SNMP_MIB_ITEM("MPTCPRetrans", MPTCP_MIB_RETRANSSEGS),
 	SNMP_MIB_ITEM("MPJoinNoTokenFound", MPTCP_MIB_JOINNOTOKEN),
 	SNMP_MIB_ITEM("MPJoinSynRx", MPTCP_MIB_JOINSYNRX),
+	SNMP_MIB_ITEM("MPJoinSynBackupRx", MPTCP_MIB_JOINSYNBACKUPRX),
 	SNMP_MIB_ITEM("MPJoinSynAckRx", MPTCP_MIB_JOINSYNACKRX),
+	SNMP_MIB_ITEM("MPJoinSynAckBackupRx", MPTCP_MIB_JOINSYNACKBACKUPRX),
 	SNMP_MIB_ITEM("MPJoinSynAckHMacFailure", MPTCP_MIB_JOINSYNACKMAC),
 	SNMP_MIB_ITEM("MPJoinAckRx", MPTCP_MIB_JOINACKRX),
 	SNMP_MIB_ITEM("MPJoinAckHMacFailure", MPTCP_MIB_JOINACKMAC),
 	SNMP_MIB_ITEM("DSSNotMatching", MPTCP_MIB_DSSNOMATCH),
+	SNMP_MIB_ITEM("DSSCorruptionFallback", MPTCP_MIB_DSSCORRUPTIONFALLBACK),
+	SNMP_MIB_ITEM("DSSCorruptionReset", MPTCP_MIB_DSSCORRUPTIONRESET),
 	SNMP_MIB_ITEM("InfiniteMapRx", MPTCP_MIB_INFINITEMAPRX),
 	SNMP_MIB_ITEM("DSSNoMatchTCP", MPTCP_MIB_DSSTCPMISMATCH),
 	SNMP_MIB_ITEM("DataCsumErr", MPTCP_MIB_DATACSUMERR),
@@ -35,12 +40,14 @@
 	SNMP_MIB_ITEM("AddAddr", MPTCP_MIB_ADDADDR),
 	SNMP_MIB_ITEM("EchoAdd", MPTCP_MIB_ECHOADD),
 	SNMP_MIB_ITEM("PortAdd", MPTCP_MIB_PORTADD),
+	SNMP_MIB_ITEM("AddAddrDrop", MPTCP_MIB_ADDADDRDROP),
 	SNMP_MIB_ITEM("MPJoinPortSynRx", MPTCP_MIB_JOINPORTSYNRX),
 	SNMP_MIB_ITEM("MPJoinPortSynAckRx", MPTCP_MIB_JOINPORTSYNACKRX),
 	SNMP_MIB_ITEM("MPJoinPortAckRx", MPTCP_MIB_JOINPORTACKRX),
 	SNMP_MIB_ITEM("MismatchPortSynRx", MPTCP_MIB_MISMATCHPORTSYNRX),
 	SNMP_MIB_ITEM("MismatchPortAckRx", MPTCP_MIB_MISMATCHPORTACKRX),
 	SNMP_MIB_ITEM("RmAddr", MPTCP_MIB_RMADDR),
+	SNMP_MIB_ITEM("RmAddrDrop", MPTCP_MIB_RMADDRDROP),
 	SNMP_MIB_ITEM("RmSubflow", MPTCP_MIB_RMSUBFLOW),
 	SNMP_MIB_ITEM("MPPrioTx", MPTCP_MIB_MPPRIOTX),
 	SNMP_MIB_ITEM("MPPrioRx", MPTCP_MIB_MPPRIORX),
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/mib.h
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/mib.h
@@ -8,15 +8,20 @@
 	MPTCP_MIB_MPCAPABLEPASSIVEACK,	/* Received third ACK with MP_CAPABLE */
 	MPTCP_MIB_MPCAPABLEPASSIVEFALLBACK,/* Server-side fallback during 3-way handshake */
 	MPTCP_MIB_MPCAPABLEACTIVEFALLBACK, /* Client-side fallback during 3-way handshake */
+	MPTCP_MIB_MPCAPABLEENDPATTEMPT,	/* Prohibited MPC to port-based endp */
 	MPTCP_MIB_TOKENFALLBACKINIT,	/* Could not init/allocate token */
 	MPTCP_MIB_RETRANSSEGS,		/* Segments retransmitted at the MPTCP-level */
 	MPTCP_MIB_JOINNOTOKEN,		/* Received MP_JOIN but the token was not found */
 	MPTCP_MIB_JOINSYNRX,		/* Received a SYN + MP_JOIN */
+	MPTCP_MIB_JOINSYNBACKUPRX,	/* Received a SYN + MP_JOIN + backup flag */
 	MPTCP_MIB_JOINSYNACKRX,		/* Received a SYN/ACK + MP_JOIN */
+	MPTCP_MIB_JOINSYNACKBACKUPRX,	/* Received a SYN/ACK + MP_JOIN + backup flag */
 	MPTCP_MIB_JOINSYNACKMAC,	/* HMAC was wrong on SYN/ACK + MP_JOIN */
 	MPTCP_MIB_JOINACKRX,		/* Received an ACK + MP_JOIN */
 	MPTCP_MIB_JOINACKMAC,		/* HMAC was wrong on ACK + MP_JOIN */
 	MPTCP_MIB_DSSNOMATCH,		/* Received a new mapping that did not match the previous one */
+	MPTCP_MIB_DSSCORRUPTIONFALLBACK,/* DSS corruption detected, fallback */
+	MPTCP_MIB_DSSCORRUPTIONRESET,	/* DSS corruption detected, MPJ subflow reset */
 	MPTCP_MIB_INFINITEMAPRX,	/* Received an infinite mapping */
 	MPTCP_MIB_DSSTCPMISMATCH,	/* DSS-mapping did not map with TCP's sequence numbers */
 	MPTCP_MIB_DATACSUMERR,		/* The data checksum fail */
@@ -28,12 +33,14 @@
 	MPTCP_MIB_ADDADDR,		/* Received ADD_ADDR with echo-flag=0 */
 	MPTCP_MIB_ECHOADD,		/* Received ADD_ADDR with echo-flag=1 */
 	MPTCP_MIB_PORTADD,		/* Received ADD_ADDR with a port-number */
+	MPTCP_MIB_ADDADDRDROP,		/* Dropped incoming ADD_ADDR */
 	MPTCP_MIB_JOINPORTSYNRX,	/* Received a SYN MP_JOIN with a different port-number */
 	MPTCP_MIB_JOINPORTSYNACKRX,	/* Received a SYNACK MP_JOIN with a different port-number */
 	MPTCP_MIB_JOINPORTACKRX,	/* Received an ACK MP_JOIN with a different port-number */
 	MPTCP_MIB_MISMATCHPORTSYNRX,	/* Received a SYN MP_JOIN with a mismatched port-number */
 	MPTCP_MIB_MISMATCHPORTACKRX,	/* Received an ACK MP_JOIN with a mismatched port-number */
 	MPTCP_MIB_RMADDR,		/* Received RM_ADDR */
+	MPTCP_MIB_RMADDRDROP,		/* Dropped incoming RM_ADDR */
 	MPTCP_MIB_RMSUBFLOW,		/* Remove a subflow */
 	MPTCP_MIB_MPPRIOTX,		/* Transmit a MP_PRIO */
 	MPTCP_MIB_MPPRIORX,		/* Received a MP_PRIO */
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/mptcp_diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/mptcp_diag.c
@@ -66,20 +66,103 @@
 	return err;
 }
 
+struct mptcp_diag_ctx {
+	long s_slot;
+	long s_num;
+	unsigned int l_slot;
+	unsigned int l_num;
+};
+
+static void mptcp_diag_dump_listeners(struct sk_buff *skb, struct netlink_callback *cb,
+				      const struct inet_diag_req_v2 *r,
+				      bool net_admin)
+{
+	struct inet_diag_dump_data *cb_data = cb->data;
+	struct mptcp_diag_ctx *diag_ctx = (void *)cb->ctx;
+	struct nlattr *bc = cb_data->inet_diag_nla_bc;
+	struct net *net = sock_net(skb->sk);
+	int i;
+
+	for (i = diag_ctx->l_slot; i <= tcp_hashinfo.lhash2_mask; i++) {
+		struct inet_listen_hashbucket *ilb;
+		struct hlist_nulls_node *node;
+		struct sock *sk;
+		int num = 0;
+
+		ilb = &tcp_hashinfo.lhash2[i];
+
+		rcu_read_lock();
+		spin_lock(&ilb->lock);
+		sk_nulls_for_each(sk, node, &ilb->nulls_head) {
+			const struct mptcp_subflow_context *ctx = mptcp_subflow_ctx(sk);
+			struct inet_sock *inet = inet_sk(sk);
+			int ret;
+
+			if (num < diag_ctx->l_num)
+				goto next_listen;
+
+			if (!ctx || strcmp(inet_csk(sk)->icsk_ulp_ops->name, "mptcp"))
+				goto next_listen;
+
+			sk = ctx->conn;
+			if (!sk || !net_eq(sock_net(sk), net))
+				goto next_listen;
+
+			if (r->sdiag_family != AF_UNSPEC &&
+			    sk->sk_family != r->sdiag_family)
+				goto next_listen;
+
+			if (r->id.idiag_sport != inet->inet_sport &&
+			    r->id.idiag_sport)
+				goto next_listen;
+
+			if (!refcount_inc_not_zero(&sk->sk_refcnt))
+				goto next_listen;
+
+			ret = sk_diag_dump(sk, skb, cb, r, bc, net_admin);
+
+			sock_put(sk);
+
+			if (ret < 0) {
+				spin_unlock(&ilb->lock);
+				rcu_read_unlock();
+				diag_ctx->l_slot = i;
+				diag_ctx->l_num = num;
+				return;
+			}
+			diag_ctx->l_num = num + 1;
+			num = 0;
+next_listen:
+			++num;
+		}
+		spin_unlock(&ilb->lock);
+		rcu_read_unlock();
+
+		cond_resched();
+		diag_ctx->l_num = 0;
+	}
+
+	diag_ctx->l_num = 0;
+	diag_ctx->l_slot = i;
+}
+
 static void mptcp_diag_dump(struct sk_buff *skb, struct netlink_callback *cb,
 			    const struct inet_diag_req_v2 *r)
 {
 	bool net_admin = netlink_net_capable(cb->skb, CAP_NET_ADMIN);
+	struct mptcp_diag_ctx *diag_ctx = (void *)cb->ctx;
 	struct net *net = sock_net(skb->sk);
 	struct inet_diag_dump_data *cb_data;
 	struct mptcp_sock *msk;
 	struct nlattr *bc;
 
+	BUILD_BUG_ON(sizeof(cb->ctx) < sizeof(*diag_ctx));
+
 	cb_data = cb->data;
 	bc = cb_data->inet_diag_nla_bc;
 
-	while ((msk = mptcp_token_iter_next(net, &cb->args[0], &cb->args[1])) !=
-	       NULL) {
+	while ((msk = mptcp_token_iter_next(net, &diag_ctx->s_slot,
+					    &diag_ctx->s_num)) != NULL) {
 		struct inet_sock *inet = (struct inet_sock *)msk;
 		struct sock *sk = (struct sock *)msk;
 		int ret = 0;
@@ -101,11 +184,14 @@
 		sock_put(sk);
 		if (ret < 0) {
 			/* will retry on the same position */
-			cb->args[1]--;
+			diag_ctx->s_num--;
 			break;
 		}
 		cond_resched();
 	}
+
+	if ((r->idiag_states & TCPF_LISTEN) && r->id.idiag_dport == 0)
+		mptcp_diag_dump_listeners(skb, cb, r, net_admin);
 }
 
 static void mptcp_diag_get_info(struct sock *sk, struct inet_diag_msg *r,
@@ -119,6 +205,19 @@
 
 	r->idiag_rqueue = sk_rmem_alloc_get(sk);
 	r->idiag_wqueue = sk_wmem_alloc_get(sk);
+
+	if (inet_sk_state_load(sk) == TCP_LISTEN) {
+		struct sock *lsk = READ_ONCE(msk->first);
+
+		if (lsk) {
+			/* override with settings from tcp listener,
+			 * so Send-Q will show accept queue.
+			 */
+			r->idiag_rqueue = READ_ONCE(lsk->sk_ack_backlog);
+			r->idiag_wqueue = READ_ONCE(lsk->sk_max_ack_backlog);
+		}
+	}
+
 	if (!info)
 		return;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/options.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/options.c
@@ -107,55 +107,50 @@
 			ptr += 2;
 		}
 		if (opsize == TCPOLEN_MPTCP_MPC_ACK_DATA_CSUM) {
-			mp_opt->csum = (__force __sum16)get_unaligned_be16(ptr);
+			mp_opt->csum = get_unaligned((__force __sum16 *)ptr);
 			mp_opt->suboptions |= OPTION_MPTCP_CSUMREQD;
 			ptr += 2;
 		}
-		pr_debug("MP_CAPABLE version=%x, flags=%x, optlen=%d sndr=%llu, rcvr=%llu len=%d csum=%u",
+		pr_debug("MP_CAPABLE version=%x, flags=%x, optlen=%d sndr=%llu, rcvr=%llu len=%d csum=%u\n",
 			 version, flags, opsize, mp_opt->sndr_key,
 			 mp_opt->rcvr_key, mp_opt->data_len, mp_opt->csum);
 		break;
 
 	case MPTCPOPT_MP_JOIN:
-		mp_opt->suboptions |= OPTIONS_MPTCP_MPJ;
 		if (opsize == TCPOLEN_MPTCP_MPJ_SYN) {
+			mp_opt->suboptions |= OPTION_MPTCP_MPJ_SYN;
 			mp_opt->backup = *ptr++ & MPTCPOPT_BACKUP;
 			mp_opt->join_id = *ptr++;
 			mp_opt->token = get_unaligned_be32(ptr);
 			ptr += 4;
 			mp_opt->nonce = get_unaligned_be32(ptr);
 			ptr += 4;
-			pr_debug("MP_JOIN bkup=%u, id=%u, token=%u, nonce=%u",
+			pr_debug("MP_JOIN bkup=%u, id=%u, token=%u, nonce=%u\n",
 				 mp_opt->backup, mp_opt->join_id,
 				 mp_opt->token, mp_opt->nonce);
 		} else if (opsize == TCPOLEN_MPTCP_MPJ_SYNACK) {
+			mp_opt->suboptions |= OPTION_MPTCP_MPJ_SYNACK;
 			mp_opt->backup = *ptr++ & MPTCPOPT_BACKUP;
 			mp_opt->join_id = *ptr++;
 			mp_opt->thmac = get_unaligned_be64(ptr);
 			ptr += 8;
 			mp_opt->nonce = get_unaligned_be32(ptr);
 			ptr += 4;
-			pr_debug("MP_JOIN bkup=%u, id=%u, thmac=%llu, nonce=%u",
+			pr_debug("MP_JOIN bkup=%u, id=%u, thmac=%llu, nonce=%u\n",
 				 mp_opt->backup, mp_opt->join_id,
 				 mp_opt->thmac, mp_opt->nonce);
 		} else if (opsize == TCPOLEN_MPTCP_MPJ_ACK) {
+			mp_opt->suboptions |= OPTION_MPTCP_MPJ_ACK;
 			ptr += 2;
 			memcpy(mp_opt->hmac, ptr, MPTCPOPT_HMAC_LEN);
-			pr_debug("MP_JOIN hmac");
-		} else {
-			mp_opt->suboptions &= ~OPTIONS_MPTCP_MPJ;
+			pr_debug("MP_JOIN hmac\n");
 		}
 		break;
 
 	case MPTCPOPT_DSS:
-		pr_debug("DSS");
+		pr_debug("DSS\n");
 		ptr++;
 
-		/* we must clear 'mpc_map' be able to detect MP_CAPABLE
-		 * map vs DSS map in mptcp_incoming_options(), and reconstruct
-		 * map info accordingly
-		 */
-		mp_opt->mpc_map = 0;
 		flags = (*ptr++) & MPTCP_DSS_FLAG_MASK;
 		mp_opt->data_fin = (flags & MPTCP_DSS_DATA_FIN) != 0;
 		mp_opt->dsn64 = (flags & MPTCP_DSS_DSN64) != 0;
@@ -163,7 +158,7 @@
 		mp_opt->ack64 = (flags & MPTCP_DSS_ACK64) != 0;
 		mp_opt->use_ack = (flags & MPTCP_DSS_HAS_ACK);
 
-		pr_debug("data_fin=%d dsn64=%d use_map=%d ack64=%d use_ack=%d",
+		pr_debug("data_fin=%d dsn64=%d use_map=%d ack64=%d use_ack=%d\n",
 			 mp_opt->data_fin, mp_opt->dsn64,
 			 mp_opt->use_map, mp_opt->ack64,
 			 mp_opt->use_ack);
@@ -201,7 +196,7 @@
 				ptr += 4;
 			}
 
-			pr_debug("data_ack=%llu", mp_opt->data_ack);
+			pr_debug("data_ack=%llu\n", mp_opt->data_ack);
 		}
 
 		if (mp_opt->use_map) {
@@ -221,11 +216,11 @@
 
 			if (opsize == expected_opsize + TCPOLEN_MPTCP_DSS_CHECKSUM) {
 				mp_opt->suboptions |= OPTION_MPTCP_CSUMREQD;
-				mp_opt->csum = (__force __sum16)get_unaligned_be16(ptr);
+				mp_opt->csum = get_unaligned((__force __sum16 *)ptr);
 				ptr += 2;
 			}
 
-			pr_debug("data_seq=%llu subflow_seq=%u data_len=%u csum=%d:%u",
+			pr_debug("data_seq=%llu subflow_seq=%u data_len=%u csum=%d:%u\n",
 				 mp_opt->data_seq, mp_opt->subflow_seq,
 				 mp_opt->data_len, !!(mp_opt->suboptions & OPTION_MPTCP_CSUMREQD),
 				 mp_opt->csum);
@@ -287,7 +282,7 @@
 			mp_opt->ahmac = get_unaligned_be64(ptr);
 			ptr += 8;
 		}
-		pr_debug("ADD_ADDR%s: id=%d, ahmac=%llu, echo=%d, port=%d",
+		pr_debug("ADD_ADDR%s: id=%d, ahmac=%llu, echo=%d, port=%d\n",
 			 (mp_opt->addr.family == AF_INET6) ? "6" : "",
 			 mp_opt->addr.id, mp_opt->ahmac, mp_opt->echo, ntohs(mp_opt->addr.port));
 		break;
@@ -303,7 +298,7 @@
 		mp_opt->rm_list.nr = opsize - TCPOLEN_MPTCP_RM_ADDR_BASE;
 		for (i = 0; i < mp_opt->rm_list.nr; i++)
 			mp_opt->rm_list.ids[i] = *ptr++;
-		pr_debug("RM_ADDR: rm_list_nr=%d", mp_opt->rm_list.nr);
+		pr_debug("RM_ADDR: rm_list_nr=%d\n", mp_opt->rm_list.nr);
 		break;
 
 	case MPTCPOPT_MP_PRIO:
@@ -312,7 +307,7 @@
 
 		mp_opt->suboptions |= OPTION_MPTCP_PRIO;
 		mp_opt->backup = *ptr++ & MPTCP_PRIO_BKUP;
-		pr_debug("MP_PRIO: prio=%d", mp_opt->backup);
+		pr_debug("MP_PRIO: prio=%d\n", mp_opt->backup);
 		break;
 
 	case MPTCPOPT_MP_FASTCLOSE:
@@ -345,7 +340,7 @@
 		ptr += 2;
 		mp_opt->suboptions |= OPTION_MPTCP_FAIL;
 		mp_opt->fail_seq = get_unaligned_be64(ptr);
-		pr_debug("MP_FAIL: data_seq=%llu", mp_opt->fail_seq);
+		pr_debug("MP_FAIL: data_seq=%llu\n", mp_opt->fail_seq);
 		break;
 
 	default:
@@ -353,16 +348,18 @@
 	}
 }
 
-void mptcp_get_options(const struct sock *sk,
-		       const struct sk_buff *skb,
+void mptcp_get_options(const struct sk_buff *skb,
 		       struct mptcp_options_received *mp_opt)
 {
 	const struct tcphdr *th = tcp_hdr(skb);
 	const unsigned char *ptr;
 	int length;
 
-	/* initialize option status */
-	mp_opt->suboptions = 0;
+	/* Ensure that casting the whole status to u32 is efficient and safe */
+	BUILD_BUG_ON(sizeof_field(struct mptcp_options_received, status) != sizeof(u32));
+	BUILD_BUG_ON(!IS_ALIGNED(offsetof(struct mptcp_options_received, status),
+				 sizeof(u32)));
+	*(u32 *)&mp_opt->status = 0;
 
 	length = (th->doff * 4) - sizeof(struct tcphdr);
 	ptr = (const unsigned char *)(th + 1);
@@ -409,7 +406,7 @@
 		*size = TCPOLEN_MPTCP_MPC_SYN;
 		return true;
 	} else if (subflow->request_join) {
-		pr_debug("remote_token=%u, nonce=%u", subflow->remote_token,
+		pr_debug("remote_token=%u, nonce=%u\n", subflow->remote_token,
 			 subflow->local_nonce);
 		opts->suboptions = OPTION_MPTCP_MPJ_SYN;
 		opts->join_id = subflow->local_id;
@@ -422,28 +419,6 @@
 	return false;
 }
 
-/* MP_JOIN client subflow must wait for 4th ack before sending any data:
- * TCP can't schedule delack timer before the subflow is fully established.
- * MPTCP uses the delack timer to do 3rd ack retransmissions
- */
-static void schedule_3rdack_retransmission(struct sock *sk)
-{
-	struct inet_connection_sock *icsk = inet_csk(sk);
-	struct tcp_sock *tp = tcp_sk(sk);
-	unsigned long timeout;
-
-	/* reschedule with a timeout above RTT, as we must look only for drop */
-	if (tp->srtt_us)
-		timeout = tp->srtt_us << 1;
-	else
-		timeout = TCP_TIMEOUT_INIT;
-
-	WARN_ON_ONCE(icsk->icsk_ack.pending & ICSK_ACK_TIMER);
-	icsk->icsk_ack.pending |= ICSK_ACK_SCHED | ICSK_ACK_TIMER;
-	icsk->icsk_ack.timeout = timeout;
-	sk_reset_timer(sk, &icsk->icsk_delack_timer, timeout);
-}
-
 static void clear_3rdack_retransmission(struct sock *sk)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
@@ -515,7 +490,7 @@
 			*size = TCPOLEN_MPTCP_MPC_ACK;
 		}
 
-		pr_debug("subflow=%p, local_key=%llu, remote_key=%llu map_len=%d",
+		pr_debug("subflow=%p, local_key=%llu, remote_key=%llu map_len=%d\n",
 			 subflow, subflow->local_key, subflow->remote_key,
 			 data_len);
 
@@ -524,9 +499,17 @@
 		opts->suboptions = OPTION_MPTCP_MPJ_ACK;
 		memcpy(opts->hmac, subflow->hmac, MPTCPOPT_HMAC_LEN);
 		*size = TCPOLEN_MPTCP_MPJ_ACK;
-		pr_debug("subflow=%p", subflow);
+		pr_debug("subflow=%p\n", subflow);
 
-		schedule_3rdack_retransmission(sk);
+		/* we can use the full delegate action helper only from BH context
+		 * If we are in process context - sk is flushing the backlog at
+		 * socket lock release time - just set the appropriate flag, will
+		 * be handled by the release callback
+		 */
+		if (sock_owned_by_user(sk))
+			set_bit(MPTCP_DELEGATE_ACK, &subflow->delegated_status);
+		else
+			mptcp_subflow_delegate(subflow, MPTCP_DELEGATE_ACK);
 		return true;
 	}
 	return false;
@@ -664,8 +647,8 @@
 	struct mptcp_sock *msk = mptcp_sk(subflow->conn);
 	bool drop_other_suboptions = false;
 	unsigned int opt_size = *size;
+	struct mptcp_addr_info addr;
 	bool echo;
-	bool port;
 	int len;
 
 	/* add addr will strip the existing options, be sure to avoid breaking
@@ -673,19 +656,26 @@
 	 */
 	if (!mptcp_pm_should_add_signal(msk) ||
 	    (opts->suboptions & (OPTION_MPTCP_MPJ_ACK | OPTION_MPTCP_MPC_ACK)) ||
-	    !mptcp_pm_add_addr_signal(msk, skb, opt_size, remaining, &opts->addr,
-		    &echo, &port, &drop_other_suboptions))
+	    !mptcp_pm_add_addr_signal(msk, skb, opt_size, remaining, &addr,
+		    &echo, &drop_other_suboptions))
 		return false;
 
+	/*
+	 * Later on, mptcp_write_options() will enforce mutually exclusion with
+	 * DSS, bail out if such option is set and we can't drop it.
+	 */
 	if (drop_other_suboptions)
 		remaining += opt_size;
-	len = mptcp_add_addr_len(opts->addr.family, echo, port);
+	else if (opts->suboptions & OPTION_MPTCP_DSS)
+		return false;
+
+	len = mptcp_add_addr_len(addr.family, echo, !!addr.port);
 	if (remaining < len)
 		return false;
 
 	*size = len;
 	if (drop_other_suboptions) {
-		pr_debug("drop other suboptions");
+		pr_debug("drop other suboptions\n");
 		opts->suboptions = 0;
 
 		/* note that e.g. DSS could have written into the memory
@@ -696,13 +686,14 @@
 		opts->ahmac = 0;
 		*size -= opt_size;
 	}
+	opts->addr = addr;
 	opts->suboptions |= OPTION_MPTCP_ADD_ADDR;
 	if (!echo) {
 		opts->ahmac = add_addr_generate_hmac(msk->local_key,
 						     msk->remote_key,
 						     &opts->addr);
 	}
-	pr_debug("addr_id=%d, ahmac=%llu, echo=%d, port=%d",
+	pr_debug("addr_id=%d, ahmac=%llu, echo=%d, port=%d\n",
 		 opts->addr.id, opts->ahmac, echo, ntohs(opts->addr.port));
 
 	return true;
@@ -733,7 +724,7 @@
 	opts->rm_list = rm_list;
 
 	for (i = 0; i < opts->rm_list.nr; i++)
-		pr_debug("rm_list_ids[%d]=%d", i, opts->rm_list.ids[i]);
+		pr_debug("rm_list_ids[%d]=%d\n", i, opts->rm_list.ids[i]);
 
 	return true;
 }
@@ -761,7 +752,7 @@
 	opts->suboptions |= OPTION_MPTCP_PRIO;
 	opts->backup = subflow->request_bkup;
 
-	pr_debug("prio=%d", opts->backup);
+	pr_debug("prio=%d\n", opts->backup);
 
 	return true;
 }
@@ -801,7 +792,7 @@
 	opts->suboptions |= OPTION_MPTCP_FAIL;
 	opts->fail_seq = subflow->map_seq;
 
-	pr_debug("MP_FAIL fail_seq=%llu", opts->fail_seq);
+	pr_debug("MP_FAIL fail_seq=%llu\n", opts->fail_seq);
 
 	return true;
 }
@@ -837,10 +828,13 @@
 	if (mptcp_established_options_mp(sk, skb, snd_data_fin, &opt_size, remaining, opts))
 		ret = true;
 	else if (mptcp_established_options_dss(sk, skb, snd_data_fin, &opt_size, remaining, opts)) {
+		unsigned int mp_fail_size;
+
 		ret = true;
-		if (mptcp_established_options_mp_fail(sk, &opt_size, remaining, opts)) {
-			*size += opt_size;
-			remaining -= opt_size;
+		if (mptcp_established_options_mp_fail(sk, &mp_fail_size,
+						      remaining - opt_size, opts)) {
+			*size += opt_size + mp_fail_size;
+			remaining -= opt_size - mp_fail_size;
 			return true;
 		}
 	}
@@ -883,16 +877,16 @@
 		opts->csum_reqd = subflow_req->csum_reqd;
 		opts->allow_join_id0 = subflow_req->allow_join_id0;
 		*size = TCPOLEN_MPTCP_MPC_SYNACK;
-		pr_debug("subflow_req=%p, local_key=%llu",
+		pr_debug("subflow_req=%p, local_key=%llu\n",
 			 subflow_req, subflow_req->local_key);
 		return true;
 	} else if (subflow_req->mp_join) {
 		opts->suboptions = OPTION_MPTCP_MPJ_SYNACK;
-		opts->backup = subflow_req->backup;
+		opts->backup = subflow_req->request_bkup;
 		opts->join_id = subflow_req->local_id;
 		opts->thmac = subflow_req->thmac;
 		opts->nonce = subflow_req->local_nonce;
-		pr_debug("req=%p, bkup=%u, id=%u, thmac=%llu, nonce=%u",
+		pr_debug("req=%p, bkup=%u, id=%u, thmac=%llu, nonce=%u\n",
 			 subflow_req, opts->backup, opts->join_id,
 			 opts->thmac, opts->nonce);
 		*size = TCPOLEN_MPTCP_MPJ_SYNACK;
@@ -934,7 +928,8 @@
 	}
 
 	if (((mp_opt->suboptions & OPTION_MPTCP_DSS) && mp_opt->use_ack) ||
-	    ((mp_opt->suboptions & OPTION_MPTCP_ADD_ADDR) && !mp_opt->echo)) {
+	    ((mp_opt->suboptions & OPTION_MPTCP_ADD_ADDR) &&
+	     (!mp_opt->echo || subflow->mp_join))) {
 		/* subflows are fully established as soon as we get any
 		 * additional ack, including ADD_ADDR.
 		 */
@@ -1019,11 +1014,9 @@
 	old_snd_una = msk->snd_una;
 	new_snd_una = mptcp_expand_seq(old_snd_una, mp_opt->data_ack, mp_opt->ack64);
 
-	/* ACK for data not even sent yet and even above recovery bound? Ignore.*/
-	if (unlikely(after64(new_snd_una, snd_nxt))) {
-		if (!msk->recovery || after64(new_snd_una, msk->recovery_snd_nxt))
-			new_snd_una = old_snd_una;
-	}
+	/* ACK for data not even sent yet? Ignore.*/
+	if (unlikely(after64(new_snd_una, snd_nxt)))
+		new_snd_una = old_snd_una;
 
 	new_wnd_end = new_snd_una + tcp_sk(ssk)->snd_wnd;
 
@@ -1103,7 +1096,7 @@
 		return true;
 	}
 
-	mptcp_get_options(sk, skb, &mp_opt);
+	mptcp_get_options(skb, &mp_opt);
 
 	/* The subflow can be in close state only if check_fully_established()
 	 * just sent a reset. If so, tell the caller to ignore the current packet.
@@ -1169,9 +1162,8 @@
 	 */
 	if (TCP_SKB_CB(skb)->seq == TCP_SKB_CB(skb)->end_seq) {
 		if (mp_opt.data_fin && mp_opt.data_len == 1 &&
-		    mptcp_update_rcv_data_fin(msk, mp_opt.data_seq, mp_opt.dsn64) &&
-		    schedule_work(&msk->work))
-			sock_hold(subflow->conn);
+		    mptcp_update_rcv_data_fin(msk, mp_opt.data_seq, mp_opt.dsn64))
+			mptcp_schedule_work((struct sock *)msk);
 
 		return true;
 	}
@@ -1227,7 +1219,7 @@
 		WRITE_ONCE(msk->rcv_wnd_sent, ack_seq);
 }
 
-static u16 __mptcp_make_csum(u64 data_seq, u32 subflow_seq, u16 data_len, __sum16 sum)
+__sum16 __mptcp_make_csum(u64 data_seq, u32 subflow_seq, u16 data_len, __wsum sum)
 {
 	struct csum_pseudo_header header;
 	__wsum csum;
@@ -1242,14 +1234,24 @@
 	header.data_len = htons(data_len);
 	header.csum = 0;
 
-	csum = csum_partial(&header, sizeof(header), ~csum_unfold(sum));
-	return (__force u16)csum_fold(csum);
+	csum = csum_partial(&header, sizeof(header), sum);
+	return csum_fold(csum);
 }
 
-static u16 mptcp_make_csum(const struct mptcp_ext *mpext)
+static __sum16 mptcp_make_csum(const struct mptcp_ext *mpext)
 {
 	return __mptcp_make_csum(mpext->data_seq, mpext->subflow_seq, mpext->data_len,
-				 mpext->csum);
+				 ~csum_unfold(mpext->csum));
+}
+
+static void put_len_csum(u16 len, __sum16 csum, void *data)
+{
+	__sum16 *sumptr = data + 2;
+	__be16 *ptr = data;
+
+	put_unaligned_be16(len, ptr);
+
+	put_unaligned(csum, sumptr);
 }
 
 void mptcp_write_options(__be32 *ptr, const struct tcp_sock *tp,
@@ -1328,12 +1330,14 @@
 			put_unaligned_be32(mpext->subflow_seq, ptr);
 			ptr += 1;
 			if (opts->csum_reqd) {
-				put_unaligned_be32(mpext->data_len << 16 |
-						   mptcp_make_csum(mpext), ptr);
+				put_len_csum(mpext->data_len,
+					     mptcp_make_csum(mpext),
+					     ptr);
 			} else {
 				put_unaligned_be32(mpext->data_len << 16 |
 						   TCPOPT_NOP << 8 | TCPOPT_NOP, ptr);
 			}
+			ptr += 1;
 		}
 	} else if ((OPTION_MPTCP_MPC_SYN | OPTION_MPTCP_MPC_SYNACK |
 		    OPTION_MPTCP_MPC_ACK) & opts->suboptions) {
@@ -1376,11 +1380,12 @@
 			goto mp_capable_done;
 
 		if (opts->csum_reqd) {
-			put_unaligned_be32(opts->data_len << 16 |
-					   __mptcp_make_csum(opts->data_seq,
-							     opts->subflow_seq,
-							     opts->data_len,
-							     opts->csum), ptr);
+			put_len_csum(opts->data_len,
+				     __mptcp_make_csum(opts->data_seq,
+						       opts->subflow_seq,
+						       opts->data_len,
+						       ~csum_unfold(opts->csum)),
+				     ptr);
 		} else {
 			put_unaligned_be32(opts->data_len << 16 |
 					   TCPOPT_NOP << 8 | TCPOPT_NOP, ptr);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/pm.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/pm.c
@@ -20,7 +20,7 @@
 {
 	u8 add_addr = READ_ONCE(msk->pm.addr_signal);
 
-	pr_debug("msk=%p, local_id=%d, echo=%d", msk, addr->id, echo);
+	pr_debug("msk=%p, local_id=%d, echo=%d\n", msk, addr->id, echo);
 
 	lockdep_assert_held(&msk->pm.lock);
 
@@ -45,7 +45,7 @@
 {
 	u8 rm_addr = READ_ONCE(msk->pm.addr_signal);
 
-	pr_debug("msk=%p, rm_list_nr=%d", msk, rm_list->nr);
+	pr_debug("msk=%p, rm_list_nr=%d\n", msk, rm_list->nr);
 
 	if (rm_addr) {
 		pr_warn("addr_signal error, rm_addr=%d", rm_addr);
@@ -61,7 +61,7 @@
 
 int mptcp_pm_remove_subflow(struct mptcp_sock *msk, const struct mptcp_rm_list *rm_list)
 {
-	pr_debug("msk=%p, rm_list_nr=%d", msk, rm_list->nr);
+	pr_debug("msk=%p, rm_list_nr=%d\n", msk, rm_list->nr);
 
 	spin_lock_bh(&msk->pm.lock);
 	mptcp_pm_nl_rm_subflow_received(msk, rm_list);
@@ -75,7 +75,7 @@
 {
 	struct mptcp_pm_data *pm = &msk->pm;
 
-	pr_debug("msk=%p, token=%u side=%d", msk, msk->token, server_side);
+	pr_debug("msk=%p, token=%u side=%d\n", msk, msk->token, server_side);
 
 	WRITE_ONCE(pm->server_side, server_side);
 	mptcp_event(MPTCP_EVENT_CREATED, msk, ssk, GFP_ATOMIC);
@@ -89,7 +89,7 @@
 
 	subflows_max = mptcp_pm_get_subflows_max(msk);
 
-	pr_debug("msk=%p subflows=%d max=%d allow=%d", msk, pm->subflows,
+	pr_debug("msk=%p subflows=%d max=%d allow=%d\n", msk, pm->subflows,
 		 subflows_max, READ_ONCE(pm->accept_subflow));
 
 	/* try to avoid acquiring the lock below */
@@ -113,7 +113,7 @@
 static bool mptcp_pm_schedule_work(struct mptcp_sock *msk,
 				   enum mptcp_pm_status new_status)
 {
-	pr_debug("msk=%p status=%x new=%lx", msk, msk->pm.status,
+	pr_debug("msk=%p status=%x new=%lx\n", msk, msk->pm.status,
 		 BIT(new_status));
 	if (msk->pm.status & BIT(new_status))
 		return false;
@@ -128,7 +128,7 @@
 	struct mptcp_pm_data *pm = &msk->pm;
 	bool announce = false;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	spin_lock_bh(&pm->lock);
 
@@ -152,14 +152,14 @@
 
 void mptcp_pm_connection_closed(struct mptcp_sock *msk)
 {
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 }
 
 void mptcp_pm_subflow_established(struct mptcp_sock *msk)
 {
 	struct mptcp_pm_data *pm = &msk->pm;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	if (!READ_ONCE(pm->work_pending))
 		return;
@@ -174,7 +174,7 @@
 
 void mptcp_pm_subflow_closed(struct mptcp_sock *msk, u8 id)
 {
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 }
 
 void mptcp_pm_add_addr_received(struct mptcp_sock *msk,
@@ -182,29 +182,33 @@
 {
 	struct mptcp_pm_data *pm = &msk->pm;
 
-	pr_debug("msk=%p remote_id=%d accept=%d", msk, addr->id,
+	pr_debug("msk=%p remote_id=%d accept=%d\n", msk, addr->id,
 		 READ_ONCE(pm->accept_addr));
 
 	mptcp_event_addr_announced(msk, addr);
 
 	spin_lock_bh(&pm->lock);
 
-	if (!READ_ONCE(pm->accept_addr)) {
+	/* id0 should not have a different address */
+	if ((addr->id == 0 && !mptcp_pm_nl_is_init_remote_addr(msk, addr)) ||
+	    (addr->id > 0 && !READ_ONCE(pm->accept_addr))) {
 		mptcp_pm_announce_addr(msk, addr, true);
 		mptcp_pm_add_addr_send_ack(msk);
 	} else if (mptcp_pm_schedule_work(msk, MPTCP_PM_ADD_ADDR_RECEIVED)) {
 		pm->remote = *addr;
+	} else {
+		__MPTCP_INC_STATS(sock_net((struct sock *)msk), MPTCP_MIB_ADDADDRDROP);
 	}
 
 	spin_unlock_bh(&pm->lock);
 }
 
 void mptcp_pm_add_addr_echoed(struct mptcp_sock *msk,
-			      struct mptcp_addr_info *addr)
+			      const struct mptcp_addr_info *addr)
 {
 	struct mptcp_pm_data *pm = &msk->pm;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	spin_lock_bh(&pm->lock);
 
@@ -228,14 +232,16 @@
 	struct mptcp_pm_data *pm = &msk->pm;
 	u8 i;
 
-	pr_debug("msk=%p remote_ids_nr=%d", msk, rm_list->nr);
+	pr_debug("msk=%p remote_ids_nr=%d\n", msk, rm_list->nr);
 
 	for (i = 0; i < rm_list->nr; i++)
 		mptcp_event_addr_removed(msk, rm_list->ids[i]);
 
 	spin_lock_bh(&pm->lock);
-	mptcp_pm_schedule_work(msk, MPTCP_PM_RM_ADDR_RECEIVED);
-	pm->rm_list_rx = *rm_list;
+	if (mptcp_pm_schedule_work(msk, MPTCP_PM_RM_ADDR_RECEIVED))
+		pm->rm_list_rx = *rm_list;
+	else
+		__MPTCP_INC_STATS(sock_net((struct sock *)msk), MPTCP_MIB_RMADDRDROP);
 	spin_unlock_bh(&pm->lock);
 }
 
@@ -251,19 +257,20 @@
 
 void mptcp_pm_mp_fail_received(struct sock *sk, u64 fail_seq)
 {
-	pr_debug("fail_seq=%llu", fail_seq);
+	pr_debug("fail_seq=%llu\n", fail_seq);
 }
 
 /* path manager helpers */
 
-bool mptcp_pm_add_addr_signal(struct mptcp_sock *msk, struct sk_buff *skb,
+bool mptcp_pm_add_addr_signal(struct mptcp_sock *msk, const struct sk_buff *skb,
 			      unsigned int opt_size, unsigned int remaining,
 			      struct mptcp_addr_info *addr, bool *echo,
-			      bool *port, bool *drop_other_suboptions)
+			      bool *drop_other_suboptions)
 {
 	int ret = false;
 	u8 add_addr;
 	u8 family;
+	bool port;
 
 	spin_lock_bh(&msk->pm.lock);
 
@@ -281,10 +288,10 @@
 	}
 
 	*echo = mptcp_pm_should_add_signal_echo(msk);
-	*port = !!(*echo ? msk->pm.remote.port : msk->pm.local.port);
+	port = !!(*echo ? msk->pm.remote.port : msk->pm.local.port);
 
 	family = *echo ? msk->pm.remote.family : msk->pm.local.family;
-	if (remaining < mptcp_add_addr_len(family, *echo, *port))
+	if (remaining < mptcp_add_addr_len(family, *echo, port))
 		goto out_unlock;
 
 	if (*echo) {
@@ -337,6 +344,15 @@
 	return mptcp_pm_nl_get_local_id(msk, skc);
 }
 
+bool mptcp_pm_is_backup(struct mptcp_sock *msk, struct sock_common *skc)
+{
+	struct mptcp_addr_info skc_local;
+
+	mptcp_local_address((struct sock_common *)skc, &skc_local);
+
+	return mptcp_pm_nl_is_backup(msk, &skc_local);
+}
+
 void mptcp_pm_subflow_chk_stale(const struct mptcp_sock *msk, struct sock *ssk)
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(ssk);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/pm_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/pm_netlink.c
@@ -38,7 +38,8 @@
 	u8			retrans_times;
 };
 
-#define MAX_ADDR_ID		255
+/* max value of mptcp_addr_info.id */
+#define MAX_ADDR_ID		U8_MAX
 #define BITMAP_SZ DIV_ROUND_UP(MAX_ADDR_ID + 1, BITS_PER_LONG)
 
 struct pm_nl_pernet {
@@ -59,7 +60,7 @@
 #define ADD_ADDR_RETRANS_MAX	3
 
 static bool addresses_equal(const struct mptcp_addr_info *a,
-			    struct mptcp_addr_info *b, bool use_port)
+			    const struct mptcp_addr_info *b, bool use_port)
 {
 	bool addr_equals = false;
 
@@ -96,8 +97,7 @@
 	return addresses_equal(addr, &zero, true);
 }
 
-static void local_address(const struct sock_common *skc,
-			  struct mptcp_addr_info *addr)
+void mptcp_local_address(const struct sock_common *skc, struct mptcp_addr_info *addr)
 {
 	addr->family = skc->skc_family;
 	addr->port = htons(skc->skc_num);
@@ -123,7 +123,7 @@
 }
 
 static bool lookup_subflow_by_saddr(const struct list_head *list,
-				    struct mptcp_addr_info *saddr)
+				    const struct mptcp_addr_info *saddr)
 {
 	struct mptcp_subflow_context *subflow;
 	struct mptcp_addr_info cur;
@@ -132,7 +132,7 @@
 	list_for_each_entry(subflow, list, node) {
 		skc = (struct sock_common *)mptcp_subflow_tcp_sock(subflow);
 
-		local_address(skc, &cur);
+		mptcp_local_address(skc, &cur);
 		if (addresses_equal(&cur, saddr, saddr->port))
 			return true;
 	}
@@ -141,16 +141,19 @@
 }
 
 static bool lookup_subflow_by_daddr(const struct list_head *list,
-				    struct mptcp_addr_info *daddr)
+				    const struct mptcp_addr_info *daddr)
 {
 	struct mptcp_subflow_context *subflow;
 	struct mptcp_addr_info cur;
-	struct sock_common *skc;
 
 	list_for_each_entry(subflow, list, node) {
-		skc = (struct sock_common *)mptcp_subflow_tcp_sock(subflow);
+		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
+
+		if (!((1 << inet_sk_state_load(ssk)) &
+		      (TCPF_ESTABLISHED | TCPF_SYN_SENT | TCPF_SYN_RECV)))
+			continue;
 
-		remote_address(skc, &cur);
+		remote_address((struct sock_common *)ssk, &cur);
 		if (addresses_equal(&cur, daddr, daddr->port))
 			return true;
 	}
@@ -158,12 +161,14 @@
 	return false;
 }
 
-static struct mptcp_pm_addr_entry *
+static bool
 select_local_address(const struct pm_nl_pernet *pernet,
-		     struct mptcp_sock *msk)
+		     struct mptcp_sock *msk,
+		     struct mptcp_pm_addr_entry *new_entry)
 {
-	struct mptcp_pm_addr_entry *entry, *ret = NULL;
-	struct sock *sk = (struct sock *)msk;
+	const struct sock *sk = (const struct sock *)msk;
+	struct mptcp_pm_addr_entry *entry;
+	bool found = false;
 
 	msk_owned_by_me(msk);
 
@@ -187,18 +192,22 @@
 		 * pending join
 		 */
 		if (!lookup_subflow_by_saddr(&msk->conn_list, &entry->addr)) {
-			ret = entry;
+			*new_entry = *entry;
+			found = true;
 			break;
 		}
 	}
 	rcu_read_unlock();
-	return ret;
+
+	return found;
 }
 
-static struct mptcp_pm_addr_entry *
-select_signal_address(struct pm_nl_pernet *pernet, unsigned int pos)
+static bool
+select_signal_address(struct pm_nl_pernet *pernet, unsigned int pos,
+		      struct mptcp_pm_addr_entry *new_entry)
 {
-	struct mptcp_pm_addr_entry *entry, *ret = NULL;
+	struct mptcp_pm_addr_entry *entry;
+	bool found = false;
 	int i = 0;
 
 	rcu_read_lock();
@@ -211,24 +220,26 @@
 		if (!(entry->flags & MPTCP_PM_ADDR_FLAG_SIGNAL))
 			continue;
 		if (i++ == pos) {
-			ret = entry;
+			*new_entry = *entry;
+			found = true;
 			break;
 		}
 	}
 	rcu_read_unlock();
-	return ret;
+
+	return found;
 }
 
-unsigned int mptcp_pm_get_add_addr_signal_max(struct mptcp_sock *msk)
+unsigned int mptcp_pm_get_add_addr_signal_max(const struct mptcp_sock *msk)
 {
-	struct pm_nl_pernet *pernet;
+	const struct pm_nl_pernet *pernet;
 
-	pernet = net_generic(sock_net((struct sock *)msk), pm_nl_pernet_id);
+	pernet = net_generic(sock_net((const struct sock *)msk), pm_nl_pernet_id);
 	return READ_ONCE(pernet->add_addr_signal_max);
 }
 EXPORT_SYMBOL_GPL(mptcp_pm_get_add_addr_signal_max);
 
-unsigned int mptcp_pm_get_add_addr_accept_max(struct mptcp_sock *msk)
+unsigned int mptcp_pm_get_add_addr_accept_max(const struct mptcp_sock *msk)
 {
 	struct pm_nl_pernet *pernet;
 
@@ -237,7 +248,7 @@
 }
 EXPORT_SYMBOL_GPL(mptcp_pm_get_add_addr_accept_max);
 
-unsigned int mptcp_pm_get_subflows_max(struct mptcp_sock *msk)
+unsigned int mptcp_pm_get_subflows_max(const struct mptcp_sock *msk)
 {
 	struct pm_nl_pernet *pernet;
 
@@ -246,7 +257,7 @@
 }
 EXPORT_SYMBOL_GPL(mptcp_pm_get_subflows_max);
 
-unsigned int mptcp_pm_get_local_addr_max(struct mptcp_sock *msk)
+unsigned int mptcp_pm_get_local_addr_max(const struct mptcp_sock *msk)
 {
 	struct pm_nl_pernet *pernet;
 
@@ -264,8 +275,8 @@
 }
 
 struct mptcp_pm_add_entry *
-mptcp_lookup_anno_list_by_saddr(struct mptcp_sock *msk,
-				struct mptcp_addr_info *addr)
+mptcp_lookup_anno_list_by_saddr(const struct mptcp_sock *msk,
+				const struct mptcp_addr_info *addr)
 {
 	struct mptcp_pm_add_entry *entry;
 
@@ -285,7 +296,7 @@
 	struct mptcp_addr_info saddr;
 	bool ret = false;
 
-	local_address((struct sock_common *)sk, &saddr);
+	mptcp_local_address((struct sock_common *)sk, &saddr);
 
 	spin_lock_bh(&msk->pm.lock);
 	list_for_each_entry(entry, &msk->pm.anno_list, list) {
@@ -306,7 +317,7 @@
 	struct mptcp_sock *msk = entry->sock;
 	struct sock *sk = (struct sock *)msk;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	if (!msk)
 		return;
@@ -325,7 +336,7 @@
 	spin_lock_bh(&msk->pm.lock);
 
 	if (!mptcp_pm_should_add_signal_addr(msk)) {
-		pr_debug("retransmit ADD_ADDR id=%d", entry->addr.id);
+		pr_debug("retransmit ADD_ADDR id=%d\n", entry->addr.id);
 		mptcp_pm_announce_addr(msk, &entry->addr, false);
 		mptcp_pm_add_addr_send_ack(msk);
 		entry->retrans_times++;
@@ -346,25 +357,31 @@
 
 struct mptcp_pm_add_entry *
 mptcp_pm_del_add_timer(struct mptcp_sock *msk,
-		       struct mptcp_addr_info *addr, bool check_id)
+		       const struct mptcp_addr_info *addr, bool check_id)
 {
 	struct mptcp_pm_add_entry *entry;
 	struct sock *sk = (struct sock *)msk;
+	struct timer_list *add_timer = NULL;
 
 	spin_lock_bh(&msk->pm.lock);
 	entry = mptcp_lookup_anno_list_by_saddr(msk, addr);
-	if (entry && (!check_id || entry->addr.id == addr->id))
+	if (entry && (!check_id || entry->addr.id == addr->id)) {
 		entry->retrans_times = ADD_ADDR_RETRANS_MAX;
+		add_timer = &entry->add_timer;
+	}
+	if (!check_id && entry)
+		list_del(&entry->list);
 	spin_unlock_bh(&msk->pm.lock);
 
-	if (entry && (!check_id || entry->addr.id == addr->id))
-		sk_stop_timer_sync(sk, &entry->add_timer);
+	/* no lock, because sk_stop_timer_sync() is calling del_timer_sync() */
+	if (add_timer)
+		sk_stop_timer_sync(sk, add_timer);
 
 	return entry;
 }
 
 static bool mptcp_pm_alloc_anno_list(struct mptcp_sock *msk,
-				     struct mptcp_pm_addr_entry *entry)
+				     const struct mptcp_pm_addr_entry *entry)
 {
 	struct mptcp_pm_add_entry *add_entry = NULL;
 	struct sock *sk = (struct sock *)msk;
@@ -398,7 +415,7 @@
 	struct sock *sk = (struct sock *)msk;
 	LIST_HEAD(free_list);
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	spin_lock_bh(&msk->pm.lock);
 	list_splice_init(&msk->pm.anno_list, &free_list);
@@ -410,8 +427,8 @@
 	}
 }
 
-static bool lookup_address_in_vec(struct mptcp_addr_info *addrs, unsigned int nr,
-				  struct mptcp_addr_info *addr)
+static bool lookup_address_in_vec(const struct mptcp_addr_info *addrs, unsigned int nr,
+				  const struct mptcp_addr_info *addr)
 {
 	int i;
 
@@ -459,10 +476,22 @@
 	return i;
 }
 
+static struct mptcp_pm_addr_entry *
+__lookup_addr(struct pm_nl_pernet *pernet, struct mptcp_addr_info *info)
+{
+	struct mptcp_pm_addr_entry *entry;
+
+	list_for_each_entry(entry, &pernet->local_addr_list, list) {
+		if (addresses_equal(&entry->addr, info, true))
+			return entry;
+	}
+	return NULL;
+}
+
 static void mptcp_pm_create_subflow_or_signal_addr(struct mptcp_sock *msk)
 {
 	struct sock *sk = (struct sock *)msk;
-	struct mptcp_pm_addr_entry *local;
+	struct mptcp_pm_addr_entry local;
 	unsigned int add_addr_signal_max;
 	unsigned int local_addr_max;
 	struct pm_nl_pernet *pernet;
@@ -481,13 +510,11 @@
 
 	/* check first for announce */
 	if (msk->pm.add_addr_signaled < add_addr_signal_max) {
-		local = select_signal_address(pernet,
-					      msk->pm.add_addr_signaled);
-
-		if (local) {
-			if (mptcp_pm_alloc_anno_list(msk, local)) {
+		if (select_signal_address(pernet, msk->pm.add_addr_signaled,
+					  &local)) {
+			if (mptcp_pm_alloc_anno_list(msk, &local)) {
 				msk->pm.add_addr_signaled++;
-				mptcp_pm_announce_addr(msk, &local->addr, false);
+				mptcp_pm_announce_addr(msk, &local.addr, false);
 				mptcp_pm_nl_addr_send_ack(msk);
 			}
 		} else {
@@ -502,9 +529,8 @@
 	if (msk->pm.local_addr_used < local_addr_max &&
 	    msk->pm.subflows < subflows_max &&
 	    !READ_ONCE(msk->pm.remote_deny_join_id0)) {
-		local = select_local_address(pernet, msk);
-		if (local) {
-			bool fullmesh = !!(local->flags & MPTCP_PM_ADDR_FLAG_FULLMESH);
+		if (select_local_address(pernet, msk, &local)) {
+			bool fullmesh = !!(local.flags & MPTCP_PM_ADDR_FLAG_FULLMESH);
 			struct mptcp_addr_info addrs[MPTCP_PM_ADDR_MAX];
 			int i, nr;
 
@@ -513,7 +539,7 @@
 			nr = fill_remote_addresses_vec(msk, fullmesh, addrs);
 			spin_unlock_bh(&msk->pm.lock);
 			for (i = 0; i < nr; i++)
-				__mptcp_subflow_connect(sk, &local->addr, &addrs[i]);
+				__mptcp_subflow_connect(sk, &local.addr, &addrs[i]);
 			spin_lock_bh(&msk->pm.lock);
 			return;
 		}
@@ -542,7 +568,7 @@
 {
 	struct sock *sk = (struct sock *)msk;
 	struct mptcp_pm_addr_entry *entry;
-	struct mptcp_addr_info local;
+	struct mptcp_addr_info mpc_addr;
 	struct pm_nl_pernet *pernet;
 	unsigned int subflows_max;
 	int i = 0;
@@ -550,6 +576,8 @@
 	pernet = net_generic(sock_net(sk), pm_nl_pernet_id);
 	subflows_max = mptcp_pm_get_subflows_max(msk);
 
+	mptcp_local_address((struct sock_common *)msk, &mpc_addr);
+
 	rcu_read_lock();
 	__mptcp_flush_join_list(msk);
 	list_for_each_entry_rcu(entry, &pernet->local_addr_list, list) {
@@ -568,7 +596,13 @@
 
 		if (msk->pm.subflows < subflows_max) {
 			msk->pm.subflows++;
-			addrs[i++] = entry->addr;
+			addrs[i] = entry->addr;
+
+			/* Special case for ID0: set the correct ID */
+			if (addresses_equal(&entry->addr, &mpc_addr, entry->addr.port))
+				addrs[i].id = 0;
+
+			i++;
 		}
 	}
 	rcu_read_unlock();
@@ -577,6 +611,8 @@
 	 * 'IPADDRANY' local address
 	 */
 	if (!i) {
+		struct mptcp_addr_info local;
+
 		memset(&local, 0, sizeof(local));
 		local.family = msk->pm.remote.family;
 
@@ -594,41 +630,63 @@
 	unsigned int add_addr_accept_max;
 	struct mptcp_addr_info remote;
 	unsigned int subflows_max;
+	bool reset_port = false;
+	bool sf_created = false;
 	int i, nr;
 
 	add_addr_accept_max = mptcp_pm_get_add_addr_accept_max(msk);
 	subflows_max = mptcp_pm_get_subflows_max(msk);
 
-	pr_debug("accepted %d:%d remote family %d",
+	pr_debug("accepted %d:%d remote family %d\n",
 		 msk->pm.add_addr_accepted, add_addr_accept_max,
 		 msk->pm.remote.family);
 
-	if (lookup_subflow_by_daddr(&msk->conn_list, &msk->pm.remote))
+	remote = msk->pm.remote;
+	if (lookup_subflow_by_daddr(&msk->conn_list, &remote))
 		goto add_addr_echo;
 
+	/* pick id 0 port, if none is provided the remote address */
+	if (!remote.port) {
+		reset_port = true;
+		remote.port = sk->sk_dport;
+	}
+
 	/* connect to the specified remote address, using whatever
 	 * local address the routing configuration will pick.
 	 */
-	remote = msk->pm.remote;
-	if (!remote.port)
-		remote.port = sk->sk_dport;
 	nr = fill_local_addresses_vec(msk, addrs);
 
-	msk->pm.add_addr_accepted++;
-	if (msk->pm.add_addr_accepted >= add_addr_accept_max ||
-	    msk->pm.subflows >= subflows_max)
-		WRITE_ONCE(msk->pm.accept_addr, false);
-
 	spin_unlock_bh(&msk->pm.lock);
 	for (i = 0; i < nr; i++)
-		__mptcp_subflow_connect(sk, &addrs[i], &remote);
+		if (__mptcp_subflow_connect(sk, &addrs[i], &remote) == 0)
+			sf_created = true;
 	spin_lock_bh(&msk->pm.lock);
 
+	if (sf_created) {
+		msk->pm.add_addr_accepted++;
+		if (msk->pm.add_addr_accepted >= add_addr_accept_max ||
+		    msk->pm.subflows >= subflows_max)
+			WRITE_ONCE(msk->pm.accept_addr, false);
+	}
+
+	/* be sure to echo exactly the received address */
+	if (reset_port)
+		remote.port = 0;
+
 add_addr_echo:
-	mptcp_pm_announce_addr(msk, &msk->pm.remote, true);
+	mptcp_pm_announce_addr(msk, &remote, true);
 	mptcp_pm_nl_addr_send_ack(msk);
 }
 
+bool mptcp_pm_nl_is_init_remote_addr(struct mptcp_sock *msk,
+				     const struct mptcp_addr_info *remote)
+{
+	struct mptcp_addr_info mpc_remote;
+
+	remote_address((struct sock_common *)msk, &mpc_remote);
+	return addresses_equal(&mpc_remote, remote, remote->port);
+}
+
 void mptcp_pm_nl_addr_send_ack(struct mptcp_sock *msk)
 {
 	struct mptcp_subflow_context *subflow;
@@ -641,16 +699,18 @@
 		return;
 
 	__mptcp_flush_join_list(msk);
-	subflow = list_first_entry_or_null(&msk->conn_list, typeof(*subflow), node);
-	if (subflow) {
-		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
+	mptcp_for_each_subflow(msk, subflow) {
+		if (__mptcp_subflow_active(subflow)) {
+			struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
 
-		spin_unlock_bh(&msk->pm.lock);
-		pr_debug("send ack for %s",
-			 mptcp_pm_should_add_signal(msk) ? "add_addr" : "rm_addr");
+			spin_unlock_bh(&msk->pm.lock);
+			pr_debug("send ack for %s\n",
+				 mptcp_pm_should_add_signal(msk) ? "add_addr" : "rm_addr");
 
-		mptcp_subflow_send_ack(ssk);
-		spin_lock_bh(&msk->pm.lock);
+			mptcp_subflow_send_ack(ssk);
+			spin_lock_bh(&msk->pm.lock);
+			break;
+		}
 	}
 }
 
@@ -660,24 +720,25 @@
 {
 	struct mptcp_subflow_context *subflow;
 
-	pr_debug("bkup=%d", bkup);
+	pr_debug("bkup=%d\n", bkup);
 
 	mptcp_for_each_subflow(msk, subflow) {
 		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
 		struct sock *sk = (struct sock *)msk;
 		struct mptcp_addr_info local;
 
-		local_address((struct sock_common *)ssk, &local);
+		mptcp_local_address((struct sock_common *)ssk, &local);
 		if (!addresses_equal(&local, addr, addr->port))
 			continue;
 
-		subflow->backup = bkup;
+		if (subflow->backup != bkup)
+			msk->last_snd = NULL;
 		subflow->send_mp_prio = 1;
 		subflow->request_bkup = bkup;
 		__MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_MPPRIOTX);
 
 		spin_unlock_bh(&msk->pm.lock);
-		pr_debug("send ack for mp_prio");
+		pr_debug("send ack for mp_prio\n");
 		mptcp_subflow_send_ack(ssk);
 		spin_lock_bh(&msk->pm.lock);
 
@@ -695,11 +756,14 @@
 	struct sock *sk = (struct sock *)msk;
 	u8 i;
 
-	pr_debug("%s rm_list_nr %d",
+	pr_debug("%s rm_list_nr %d\n",
 		 rm_type == MPTCP_MIB_RMADDR ? "address" : "subflow", rm_list->nr);
 
 	msk_owned_by_me(msk);
 
+	if (sk->sk_state == TCP_LISTEN)
+		return;
+
 	if (!rm_list->nr)
 		return;
 
@@ -707,33 +771,50 @@
 		return;
 
 	for (i = 0; i < rm_list->nr; i++) {
+		bool removed = false;
+
 		list_for_each_entry_safe(subflow, tmp, &msk->conn_list, node) {
 			struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
 			int how = RCV_SHUTDOWN | SEND_SHUTDOWN;
 			u8 id = subflow->local_id;
 
+			if ((1 << inet_sk_state_load(ssk)) &
+			    (TCPF_FIN_WAIT1 | TCPF_FIN_WAIT2 | TCPF_CLOSING | TCPF_CLOSE))
+				continue;
+
 			if (rm_type == MPTCP_MIB_RMADDR)
 				id = subflow->remote_id;
 
 			if (rm_list->ids[i] != id)
 				continue;
 
-			pr_debug(" -> %s rm_list_ids[%d]=%u local_id=%u remote_id=%u",
+			pr_debug(" -> %s rm_list_ids[%d]=%u local_id=%u remote_id=%u\n",
 				 rm_type == MPTCP_MIB_RMADDR ? "address" : "subflow",
 				 i, rm_list->ids[i], subflow->local_id, subflow->remote_id);
 			spin_unlock_bh(&msk->pm.lock);
 			mptcp_subflow_shutdown(sk, ssk, how);
+			removed |= subflow->request_join;
 			mptcp_close_ssk(sk, ssk, subflow);
 			spin_lock_bh(&msk->pm.lock);
 
-			if (rm_type == MPTCP_MIB_RMADDR) {
-				msk->pm.add_addr_accepted--;
-				WRITE_ONCE(msk->pm.accept_addr, true);
-			} else if (rm_type == MPTCP_MIB_RMSUBFLOW) {
-				msk->pm.local_addr_used--;
-			}
 			msk->pm.subflows--;
+			if (rm_type == MPTCP_MIB_RMSUBFLOW)
+				__MPTCP_INC_STATS(sock_net(sk), rm_type);
+		}
+		if (rm_type == MPTCP_MIB_RMADDR)
 			__MPTCP_INC_STATS(sock_net(sk), rm_type);
+		if (!removed)
+			continue;
+
+		if (rm_type == MPTCP_MIB_RMADDR && rm_list->ids[i] &&
+		    msk->pm.add_addr_accepted != 0) {
+			/* Note: if the subflow has been closed before, this
+			 * add_addr_accepted counter will not be decremented.
+			 */
+			if (--msk->pm.add_addr_accepted < mptcp_pm_get_add_addr_accept_max(msk))
+				WRITE_ONCE(msk->pm.accept_addr, true);
+		} else if (rm_type == MPTCP_MIB_RMSUBFLOW) {
+			msk->pm.local_addr_used--;
 		}
 	}
 }
@@ -757,7 +838,7 @@
 
 	spin_lock_bh(&msk->pm.lock);
 
-	pr_debug("msk=%p status=%x", msk, pm->status);
+	pr_debug("msk=%p status=%x\n", msk, pm->status);
 	if (pm->status & BIT(MPTCP_PM_ADD_ADDR_RECEIVED)) {
 		pm->status &= ~BIT(MPTCP_PM_ADD_ADDR_RECEIVED);
 		mptcp_pm_nl_add_addr_received(msk);
@@ -790,7 +871,8 @@
 }
 
 static int mptcp_pm_nl_append_new_local_addr(struct pm_nl_pernet *pernet,
-					     struct mptcp_pm_addr_entry *entry)
+					     struct mptcp_pm_addr_entry *entry,
+					     bool needs_id)
 {
 	struct mptcp_pm_addr_entry *cur;
 	unsigned int addr_max;
@@ -817,19 +899,18 @@
 			goto out;
 	}
 
-	if (!entry->addr.id) {
+	if (!entry->addr.id && needs_id) {
 find_next:
 		entry->addr.id = find_next_zero_bit(pernet->id_bitmap,
 						    MAX_ADDR_ID + 1,
 						    pernet->next_id);
-		if ((!entry->addr.id || entry->addr.id > MAX_ADDR_ID) &&
-		    pernet->next_id != 1) {
+		if (!entry->addr.id && pernet->next_id != 1) {
 			pernet->next_id = 1;
 			goto find_next;
 		}
 	}
 
-	if (!entry->addr.id || entry->addr.id > MAX_ADDR_ID)
+	if (!entry->addr.id && needs_id)
 		goto out;
 
 	__set_bit(entry->addr.id, pernet->id_bitmap);
@@ -854,12 +935,17 @@
 	return ret;
 }
 
+static struct lock_class_key mptcp_slock_keys[2];
+static struct lock_class_key mptcp_keys[2];
+
 static int mptcp_pm_nl_create_listen_socket(struct sock *sk,
 					    struct mptcp_pm_addr_entry *entry)
 {
+	bool is_ipv6 = sk->sk_family == AF_INET6;
+	int addrlen = sizeof(struct sockaddr_in);
 	struct sockaddr_storage addr;
-	struct mptcp_sock *msk;
 	struct socket *ssock;
+	struct sock *newsk;
 	int backlog = 1024;
 	int err;
 
@@ -868,26 +954,44 @@
 	if (err)
 		return err;
 
-	msk = mptcp_sk(entry->lsk->sk);
-	if (!msk) {
+	newsk = entry->lsk->sk;
+	if (!newsk) {
 		err = -EINVAL;
 		goto out;
 	}
 
-	ssock = __mptcp_nmpc_socket(msk);
+	/* The subflow socket lock is acquired in a nested to the msk one
+	 * in several places, even by the TCP stack, and this msk is a kernel
+	 * socket: lockdep complains. Instead of propagating the _nested
+	 * modifiers in several places, re-init the lock class for the msk
+	 * socket to an mptcp specific one.
+	 */
+	sock_lock_init_class_and_name(newsk,
+				      is_ipv6 ? "mlock-AF_INET6" : "mlock-AF_INET",
+				      &mptcp_slock_keys[is_ipv6],
+				      is_ipv6 ? "msk_lock-AF_INET6" : "msk_lock-AF_INET",
+				      &mptcp_keys[is_ipv6]);
+
+	lock_sock(newsk);
+	ssock = __mptcp_nmpc_socket(mptcp_sk(newsk));
+	release_sock(newsk);
 	if (!ssock) {
 		err = -EINVAL;
 		goto out;
 	}
 
 	mptcp_info2sockaddr(&entry->addr, &addr, entry->addr.family);
-	err = kernel_bind(ssock, (struct sockaddr *)&addr,
-			  sizeof(struct sockaddr_in));
+#if IS_ENABLED(CONFIG_MPTCP_IPV6)
+	if (entry->addr.family == AF_INET6)
+		addrlen = sizeof(struct sockaddr_in6);
+#endif
+	err = kernel_bind(ssock, (struct sockaddr *)&addr, addrlen);
 	if (err) {
 		pr_warn("kernel_bind error, err=%d", err);
 		goto out;
 	}
 
+	WRITE_ONCE(mptcp_subflow_ctx(ssock->sk)->pm_listener, true);
 	err = kernel_listen(ssock, backlog);
 	if (err) {
 		pr_warn("kernel_listen error, err=%d", err);
@@ -915,8 +1019,8 @@
 	/* The 0 ID mapping is defined by the first subflow, copied into the msk
 	 * addr
 	 */
-	local_address((struct sock_common *)msk, &msk_local);
-	local_address((struct sock_common *)skc, &skc_local);
+	mptcp_local_address((struct sock_common *)msk, &msk_local);
+	mptcp_local_address((struct sock_common *)skc, &skc_local);
 	if (addresses_equal(&msk_local, &skc_local, false))
 		return 0;
 
@@ -947,13 +1051,33 @@
 	entry->ifindex = 0;
 	entry->flags = 0;
 	entry->lsk = NULL;
-	ret = mptcp_pm_nl_append_new_local_addr(pernet, entry);
+	ret = mptcp_pm_nl_append_new_local_addr(pernet, entry, true);
 	if (ret < 0)
 		kfree(entry);
 
 	return ret;
 }
 
+bool mptcp_pm_nl_is_backup(struct mptcp_sock *msk, struct mptcp_addr_info *skc)
+{
+	struct mptcp_pm_addr_entry *entry;
+	struct pm_nl_pernet *pernet;
+	bool backup = false;
+
+	pernet = net_generic(sock_net((struct sock *)msk), pm_nl_pernet_id);
+
+	rcu_read_lock();
+	list_for_each_entry_rcu(entry, &pernet->local_addr_list, list) {
+		if (addresses_equal(&entry->addr, skc, entry->addr.port)) {
+			backup = !!(entry->flags & MPTCP_PM_ADDR_FLAG_BACKUP);
+			break;
+		}
+	}
+	rcu_read_unlock();
+
+	return backup;
+}
+
 void mptcp_pm_nl_data_init(struct mptcp_sock *msk)
 {
 	struct mptcp_pm_data *pm = &msk->pm;
@@ -1148,6 +1272,18 @@
 	return 0;
 }
 
+static bool mptcp_pm_has_addr_attr_id(const struct nlattr *attr,
+				      struct genl_info *info)
+{
+	struct nlattr *tb[MPTCP_PM_ADDR_ATTR_MAX + 1];
+
+	if (!nla_parse_nested_deprecated(tb, MPTCP_PM_ADDR_ATTR_MAX, attr,
+					 mptcp_pm_addr_policy, info->extack) &&
+	    tb[MPTCP_PM_ADDR_ATTR_ID])
+		return true;
+	return false;
+}
+
 static int mptcp_nl_cmd_add_addr(struct sk_buff *skb, struct genl_info *info)
 {
 	struct nlattr *attr = info->attrs[MPTCP_PM_ATTR_ADDR];
@@ -1174,7 +1310,8 @@
 			return ret;
 		}
 	}
-	ret = mptcp_pm_nl_append_new_local_addr(pernet, entry);
+	ret = mptcp_pm_nl_append_new_local_addr(pernet, entry,
+						!mptcp_pm_has_addr_attr_id(attr, info));
 	if (ret < 0) {
 		GENL_SET_ERR_MSG(info, "too many addresses or duplicate one");
 		if (entry->lsk)
@@ -1222,13 +1359,12 @@
 }
 
 static bool remove_anno_list_by_saddr(struct mptcp_sock *msk,
-				      struct mptcp_addr_info *addr)
+				      const struct mptcp_addr_info *addr)
 {
 	struct mptcp_pm_add_entry *entry;
 
 	entry = mptcp_pm_del_add_timer(msk, addr, false);
 	if (entry) {
-		list_del(&entry->list);
 		kfree(entry);
 		return true;
 	}
@@ -1237,7 +1373,7 @@
 }
 
 static bool mptcp_pm_remove_anno_addr(struct mptcp_sock *msk,
-				      struct mptcp_addr_info *addr,
+				      const struct mptcp_addr_info *addr,
 				      bool force)
 {
 	struct mptcp_rm_list list = { .nr = 0 };
@@ -1248,6 +1384,7 @@
 	ret = remove_anno_list_by_saddr(msk, addr);
 	if (ret || force) {
 		spin_lock_bh(&msk->pm.lock);
+		msk->pm.add_addr_signaled -= ret;
 		mptcp_pm_remove_addr(msk, &list);
 		spin_unlock_bh(&msk->pm.lock);
 	}
@@ -1261,7 +1398,7 @@
 	long s_slot = 0, s_num = 0;
 	struct mptcp_rm_list list = { .nr = 0 };
 
-	pr_debug("remove_id=%d", addr->id);
+	pr_debug("remove_id=%d\n", addr->id);
 
 	list.ids[list.nr++] = addr->id;
 
@@ -1269,11 +1406,6 @@
 		struct sock *sk = (struct sock *)msk;
 		bool remove_subflow;
 
-		if (list_empty(&msk->conn_list)) {
-			mptcp_pm_remove_anno_addr(msk, addr, false);
-			goto next;
-		}
-
 		lock_sock(sk);
 		remove_subflow = lookup_subflow_by_saddr(&msk->conn_list, addr);
 		mptcp_pm_remove_anno_addr(msk, addr, remove_subflow);
@@ -1281,7 +1413,6 @@
 			mptcp_pm_remove_subflow(msk, &list);
 		release_sock(sk);
 
-next:
 		sock_put(sk);
 		cond_resched();
 	}
@@ -1313,7 +1444,7 @@
 		if (list_empty(&msk->conn_list))
 			goto next;
 
-		local_address((struct sock_common *)msk, &msk_local);
+		mptcp_local_address((struct sock_common *)msk, &msk_local);
 		if (!addresses_equal(&msk_local, addr, addr->port))
 			goto next;
 
@@ -1387,24 +1518,31 @@
 	struct mptcp_pm_addr_entry *entry;
 
 	list_for_each_entry(entry, rm_list, list) {
-		if (lookup_subflow_by_saddr(&msk->conn_list, &entry->addr) &&
-		    alist.nr < MPTCP_RM_IDS_MAX &&
-		    slist.nr < MPTCP_RM_IDS_MAX) {
+		if (alist.nr < MPTCP_RM_IDS_MAX &&
+		    slist.nr < MPTCP_RM_IDS_MAX &&
+		    lookup_subflow_by_saddr(&msk->conn_list, &entry->addr)) {
 			alist.ids[alist.nr++] = entry->addr.id;
 			slist.ids[slist.nr++] = entry->addr.id;
-		} else if (remove_anno_list_by_saddr(msk, &entry->addr) &&
-			 alist.nr < MPTCP_RM_IDS_MAX) {
+		} else if (alist.nr < MPTCP_RM_IDS_MAX &&
+			   remove_anno_list_by_saddr(msk, &entry->addr)) {
 			alist.ids[alist.nr++] = entry->addr.id;
 		}
 	}
 
 	if (alist.nr) {
 		spin_lock_bh(&msk->pm.lock);
+		msk->pm.add_addr_signaled -= alist.nr;
 		mptcp_pm_remove_addr(msk, &alist);
 		spin_unlock_bh(&msk->pm.lock);
 	}
+
 	if (slist.nr)
 		mptcp_pm_remove_subflow(msk, &slist);
+
+	/* Reset counters: maybe some subflows have been removed before */
+	spin_lock_bh(&msk->pm.lock);
+	msk->pm.local_addr_used = 0;
+	spin_unlock_bh(&msk->pm.lock);
 }
 
 static void mptcp_nl_remove_addrs_list(struct net *net,
@@ -1716,17 +1854,21 @@
 	if (addr.flags & MPTCP_PM_ADDR_FLAG_BACKUP)
 		bkup = 1;
 
-	list_for_each_entry(entry, &pernet->local_addr_list, list) {
-		if (addresses_equal(&entry->addr, &addr.addr, true)) {
-			mptcp_nl_addr_backup(net, &entry->addr, bkup);
-
-			if (bkup)
-				entry->flags |= MPTCP_PM_ADDR_FLAG_BACKUP;
-			else
-				entry->flags &= ~MPTCP_PM_ADDR_FLAG_BACKUP;
-		}
+	spin_lock_bh(&pernet->lock);
+	entry = __lookup_addr(pernet, &addr.addr);
+	if (!entry) {
+		spin_unlock_bh(&pernet->lock);
+		return -EINVAL;
 	}
 
+	if (bkup)
+		entry->flags |= MPTCP_PM_ADDR_FLAG_BACKUP;
+	else
+		entry->flags &= ~MPTCP_PM_ADDR_FLAG_BACKUP;
+	addr = *entry;
+	spin_unlock_bh(&pernet->lock);
+
+	mptcp_nl_addr_backup(net, &addr.addr, bkup);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/protocol.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/protocol.c
@@ -51,7 +51,7 @@
 static struct percpu_counter mptcp_sockets_allocated;
 
 static void __mptcp_destroy_sock(struct sock *sk);
-static void __mptcp_check_send_data_fin(struct sock *sk);
+static void mptcp_check_send_data_fin(struct sock *sk);
 
 DEFINE_PER_CPU(struct mptcp_delegated_action, mptcp_delegated_actions);
 static struct net_device mptcp_napi_dev;
@@ -133,10 +133,11 @@
 	int delta;
 
 	if (MPTCP_SKB_CB(from)->offset ||
+	    ((to->len + from->len) > (sk->sk_rcvbuf >> 3)) ||
 	    !skb_try_coalesce(to, from, &fragstolen, &delta))
 		return false;
 
-	pr_debug("colesced seq %llx into %llx new len %d new end seq %llx",
+	pr_debug("colesced seq %llx into %llx new len %d new end seq %llx\n",
 		 MPTCP_SKB_CB(from)->map_seq, MPTCP_SKB_CB(to)->map_seq,
 		 to->len, MPTCP_SKB_CB(from)->end_seq);
 	MPTCP_SKB_CB(to)->end_seq = MPTCP_SKB_CB(from)->end_seq;
@@ -170,7 +171,7 @@
 	end_seq = MPTCP_SKB_CB(skb)->end_seq;
 	max_seq = READ_ONCE(msk->rcv_wnd_sent);
 
-	pr_debug("msk=%p seq=%llx limit=%llx empty=%d", msk, seq, max_seq,
+	pr_debug("msk=%p seq=%llx limit=%llx empty=%d\n", msk, seq, max_seq,
 		 RB_EMPTY_ROOT(&msk->out_of_order_queue));
 	if (after64(end_seq, max_seq)) {
 		/* out of window */
@@ -288,8 +289,10 @@
 	if (!sk_rmem_schedule(sk, skb, skb->truesize)) {
 		int amount = sk_mem_pages(skb->truesize) << SK_MEM_QUANTUM_SHIFT;
 
-		if (ssk->sk_forward_alloc < amount)
+		if (ssk->sk_forward_alloc < amount) {
+			MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_RCVPRUNED);
 			goto drop;
+		}
 
 		ssk->sk_forward_alloc -= amount;
 		sk->sk_forward_alloc += amount;
@@ -330,7 +333,7 @@
 	return false;
 }
 
-static void mptcp_stop_timer(struct sock *sk)
+static void mptcp_stop_rtx_timer(struct sock *sk)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 
@@ -355,8 +358,7 @@
 {
 	struct mptcp_sock *msk = mptcp_sk(sk);
 
-	return !__mptcp_check_fallback(msk) &&
-	       ((1 << sk->sk_state) &
+	return ((1 << sk->sk_state) &
 		(TCPF_FIN_WAIT1 | TCPF_CLOSING | TCPF_LAST_ACK)) &&
 	       msk->write_seq == READ_ONCE(msk->snd_una);
 }
@@ -406,9 +408,12 @@
 static void mptcp_set_datafin_timeout(const struct sock *sk)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
+	u32 retransmits;
+
+	retransmits = min_t(u32, icsk->icsk_retransmits,
+			    ilog2(TCP_RTO_MAX / TCP_RTO_MIN));
 
-	mptcp_sk(sk)->timer_ival = min(TCP_RTO_MAX,
-				       TCP_RTO_MIN << icsk->icsk_retransmits);
+	mptcp_sk(sk)->timer_ival = TCP_RTO_MIN << retransmits;
 }
 
 static void __mptcp_set_timeout(struct sock *sk, long tout)
@@ -458,13 +463,13 @@
 		mptcp_subflow_send_ack(mptcp_subflow_tcp_sock(subflow));
 }
 
-static void mptcp_subflow_cleanup_rbuf(struct sock *ssk)
+static void mptcp_subflow_cleanup_rbuf(struct sock *ssk, int copied)
 {
 	bool slow;
 
 	slow = lock_sock_fast(ssk);
 	if (tcp_can_send_ack(ssk))
-		tcp_cleanup_rbuf(ssk, 1);
+		tcp_cleanup_rbuf(ssk, copied);
 	unlock_sock_fast(ssk, slow);
 }
 
@@ -481,7 +486,7 @@
 			      (ICSK_ACK_PUSHED2 | ICSK_ACK_PUSHED)));
 }
 
-static void mptcp_cleanup_rbuf(struct mptcp_sock *msk)
+static void mptcp_cleanup_rbuf(struct mptcp_sock *msk, int copied)
 {
 	int old_space = READ_ONCE(msk->old_wspace);
 	struct mptcp_subflow_context *subflow;
@@ -489,14 +494,14 @@
 	int space =  __mptcp_space(sk);
 	bool cleanup, rx_empty;
 
-	cleanup = (space > 0) && (space >= (old_space << 1));
-	rx_empty = !__mptcp_rmem(sk);
+	cleanup = (space > 0) && (space >= (old_space << 1)) && copied;
+	rx_empty = !__mptcp_rmem(sk) && copied;
 
 	mptcp_for_each_subflow(msk, subflow) {
 		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
 
 		if (cleanup || mptcp_subflow_could_cleanup(ssk, rx_empty))
-			mptcp_subflow_cleanup_rbuf(ssk);
+			mptcp_subflow_cleanup_rbuf(ssk, copied);
 	}
 }
 
@@ -506,9 +511,6 @@
 	u64 rcv_data_fin_seq;
 	bool ret = false;
 
-	if (__mptcp_check_fallback(msk))
-		return ret;
-
 	/* Need to ack a DATA_FIN received from a peer while this side
 	 * of the connection is in ESTABLISHED, FIN_WAIT1, or FIN_WAIT2.
 	 * msk->rcv_data_fin was set when parsing the incoming options
@@ -546,12 +548,25 @@
 		}
 
 		ret = true;
-		mptcp_send_ack(msk);
+		if (!__mptcp_check_fallback(msk))
+			mptcp_send_ack(msk);
 		mptcp_close_wake_up(sk);
 	}
 	return ret;
 }
 
+static void mptcp_dss_corruption(struct mptcp_sock *msk, struct sock *ssk)
+{
+	if (READ_ONCE(msk->allow_infinite_fallback)) {
+		MPTCP_INC_STATS(sock_net(ssk),
+				MPTCP_MIB_DSSCORRUPTIONFALLBACK);
+		mptcp_do_fallback(ssk);
+	} else {
+		MPTCP_INC_STATS(sock_net(ssk), MPTCP_MIB_DSSCORRUPTIONRESET);
+		mptcp_subflow_reset(ssk);
+	}
+}
+
 static bool __mptcp_move_skbs_from_subflow(struct mptcp_sock *msk,
 					   struct sock *ssk,
 					   unsigned int *bytes)
@@ -575,7 +590,7 @@
 		}
 	}
 
-	pr_debug("msk=%p ssk=%p", msk, ssk);
+	pr_debug("msk=%p ssk=%p\n", msk, ssk);
 	tp = tcp_sk(ssk);
 	do {
 		u32 map_remaining, offset;
@@ -624,10 +639,12 @@
 				moved += len;
 			seq += len;
 
-			if (WARN_ON_ONCE(map_remaining < len))
-				break;
+			if (unlikely(map_remaining < len))
+				mptcp_dss_corruption(msk, ssk);
 		} else {
-			WARN_ON_ONCE(!fin);
+			if (unlikely(!fin))
+				mptcp_dss_corruption(msk, ssk);
+
 			sk_eat_skb(ssk, skb);
 			done = true;
 		}
@@ -654,7 +671,7 @@
 	u64 end_seq;
 
 	p = rb_first(&msk->out_of_order_queue);
-	pr_debug("msk=%p empty=%d", msk, RB_EMPTY_ROOT(&msk->out_of_order_queue));
+	pr_debug("msk=%p empty=%d\n", msk, RB_EMPTY_ROOT(&msk->out_of_order_queue));
 	while (p) {
 		skb = rb_to_skb(p);
 		if (after64(MPTCP_SKB_CB(skb)->map_seq, msk->ack_seq))
@@ -676,7 +693,7 @@
 			int delta = msk->ack_seq - MPTCP_SKB_CB(skb)->map_seq;
 
 			/* skip overlapping data, if any */
-			pr_debug("uncoalesced seq=%llx ack seq=%llx delta=%d",
+			pr_debug("uncoalesced seq=%llx ack seq=%llx delta=%d\n",
 				 MPTCP_SKB_CB(skb)->map_seq, msk->ack_seq,
 				 delta);
 			MPTCP_SKB_CB(skb)->offset += delta;
@@ -688,6 +705,46 @@
 	return moved;
 }
 
+static bool __mptcp_subflow_error_report(struct sock *sk, struct sock *ssk)
+{
+	int err = sock_error(ssk);
+	int ssk_state;
+
+	if (!err)
+		return false;
+
+	/* only propagate errors on fallen-back sockets or
+	 * on MPC connect
+	 */
+	if (sk->sk_state != TCP_SYN_SENT && !__mptcp_check_fallback(mptcp_sk(sk)))
+		return false;
+
+	/* We need to propagate only transition to CLOSE state.
+	 * Orphaned socket will see such state change via
+	 * subflow_sched_work_if_closed() and that path will properly
+	 * destroy the msk as needed.
+	 */
+	ssk_state = inet_sk_state_load(ssk);
+	if (ssk_state == TCP_CLOSE && !sock_flag(sk, SOCK_DEAD))
+		inet_sk_state_store(sk, ssk_state);
+	WRITE_ONCE(sk->sk_err, -err);
+
+	/* This barrier is coupled with smp_rmb() in mptcp_poll() */
+	smp_wmb();
+	sk_error_report(sk);
+	return true;
+}
+
+void __mptcp_error_report(struct sock *sk)
+{
+	struct mptcp_subflow_context *subflow;
+	struct mptcp_sock *msk = mptcp_sk(sk);
+
+	mptcp_for_each_subflow(msk, subflow)
+		if (__mptcp_subflow_error_report(sk, mptcp_subflow_tcp_sock(subflow)))
+			break;
+}
+
 /* In most cases we will be able to lock the mptcp socket.  If its already
  * owned, we need to defer to the work queue to avoid ABBA deadlock.
  */
@@ -734,10 +791,8 @@
 		sk_rbuf = ssk_rbuf;
 
 	/* over limit? can't append more skbs to msk, Also, no need to wake-up*/
-	if (__mptcp_rmem(sk) > sk_rbuf) {
-		MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_RCVPRUNED);
+	if (__mptcp_rmem(sk) > sk_rbuf)
 		return;
-	}
 
 	/* Wake-up the reader only for in-sequence data */
 	mptcp_data_lock(sk);
@@ -790,12 +845,12 @@
 	mptcp_sockopt_sync_all(msk);
 }
 
-static bool mptcp_timer_pending(struct sock *sk)
+static bool mptcp_rtx_timer_pending(struct sock *sk)
 {
 	return timer_pending(&inet_csk(sk)->icsk_retransmit_timer);
 }
 
-static void mptcp_reset_timer(struct sock *sk)
+static void mptcp_reset_rtx_timer(struct sock *sk)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	unsigned long tout;
@@ -1105,10 +1160,10 @@
 		__mptcp_mem_reclaim_partial(sk);
 
 	if (snd_una == READ_ONCE(msk->snd_nxt) && !msk->recovery) {
-		if (mptcp_timer_pending(sk) && !mptcp_data_fin_enabled(msk))
-			mptcp_stop_timer(sk);
+		if (mptcp_rtx_timer_pending(sk) && !mptcp_data_fin_enabled(msk))
+			mptcp_stop_rtx_timer(sk);
 	} else {
-		mptcp_reset_timer(sk);
+		mptcp_reset_rtx_timer(sk);
 	}
 }
 
@@ -1221,6 +1276,7 @@
 		if (likely(__mptcp_add_ext(skb, gfp))) {
 			skb_reserve(skb, MAX_TCP_HEADER);
 			skb->reserved_tailroom = skb->end - skb->tail;
+			INIT_LIST_HEAD(&skb->tcp_tsorted_anchor);
 			return skb;
 		}
 		__kfree_skb(skb);
@@ -1230,31 +1286,24 @@
 	return NULL;
 }
 
-static bool __mptcp_alloc_tx_skb(struct sock *sk, struct sock *ssk, gfp_t gfp)
+static struct sk_buff *__mptcp_alloc_tx_skb(struct sock *sk, struct sock *ssk, gfp_t gfp)
 {
 	struct sk_buff *skb;
 
-	if (ssk->sk_tx_skb_cache) {
-		skb = ssk->sk_tx_skb_cache;
-		if (unlikely(!skb_ext_find(skb, SKB_EXT_MPTCP) &&
-			     !__mptcp_add_ext(skb, gfp)))
-			return false;
-		return true;
-	}
-
 	skb = __mptcp_do_alloc_tx_skb(sk, gfp);
 	if (!skb)
-		return false;
+		return NULL;
 
 	if (likely(sk_wmem_schedule(ssk, skb->truesize))) {
-		ssk->sk_tx_skb_cache = skb;
-		return true;
+		tcp_skb_entail(ssk, skb);
+		return skb;
 	}
+	tcp_skb_tsorted_anchor_cleanup(skb);
 	kfree_skb(skb);
-	return false;
+	return NULL;
 }
 
-static bool mptcp_alloc_tx_skb(struct sock *sk, struct sock *ssk, bool data_lock_held)
+static struct sk_buff *mptcp_alloc_tx_skb(struct sock *sk, struct sock *ssk, bool data_lock_held)
 {
 	gfp_t gfp = data_lock_held ? GFP_ATOMIC : sk->sk_allocation;
 
@@ -1284,23 +1333,29 @@
 			      struct mptcp_sendmsg_info *info)
 {
 	u64 data_seq = dfrag->data_seq + info->sent;
+	int offset = dfrag->offset + info->sent;
 	struct mptcp_sock *msk = mptcp_sk(sk);
 	bool zero_window_probe = false;
 	struct mptcp_ext *mpext = NULL;
-	struct sk_buff *skb, *tail;
-	bool must_collapse = false;
-	int size_bias = 0;
-	int avail_size;
-	size_t ret = 0;
+	bool can_coalesce = false;
+	bool reuse_skb = true;
+	struct sk_buff *skb;
+	size_t copy;
+	int i;
 
-	pr_debug("msk=%p ssk=%p sending dfrag at seq=%llu len=%u already sent=%u",
+	pr_debug("msk=%p ssk=%p sending dfrag at seq=%llu len=%u already sent=%u\n",
 		 msk, ssk, dfrag->data_seq, dfrag->data_len, info->sent);
 
+	if (WARN_ON_ONCE(info->sent > info->limit ||
+			 info->limit > dfrag->data_len))
+		return 0;
+
 	/* compute send limit */
 	info->mss_now = tcp_send_mss(ssk, &info->size_goal, info->flags);
-	avail_size = info->size_goal;
+	copy = info->size_goal;
+
 	skb = tcp_write_queue_tail(ssk);
-	if (skb) {
+	if (skb && copy > skb->len) {
 		/* Limit the write to the size available in the
 		 * current skb, if any, so that we create at most a new skb.
 		 * Explicitly tells TCP internals to avoid collapsing on later
@@ -1310,85 +1365,98 @@
 		mpext = skb_ext_find(skb, SKB_EXT_MPTCP);
 		if (!mptcp_skb_can_collapse_to(data_seq, skb, mpext)) {
 			TCP_SKB_CB(skb)->eor = 1;
+			tcp_mark_push(tcp_sk(ssk), skb);
 			goto alloc_skb;
 		}
 
-		must_collapse = (info->size_goal > skb->len) &&
-				(skb_shinfo(skb)->nr_frags < sysctl_max_skb_frags);
-		if (must_collapse) {
-			size_bias = skb->len;
-			avail_size = info->size_goal - skb->len;
+		i = skb_shinfo(skb)->nr_frags;
+		can_coalesce = skb_can_coalesce(skb, i, dfrag->page, offset);
+		if (!can_coalesce && i >= READ_ONCE(sysctl_max_skb_frags)) {
+			tcp_mark_push(tcp_sk(ssk), skb);
+			goto alloc_skb;
 		}
-	}
 
+		copy -= skb->len;
+	} else {
 alloc_skb:
-	if (!must_collapse &&
-	    !mptcp_alloc_tx_skb(sk, ssk, info->data_lock_held))
-		return 0;
+		skb = mptcp_alloc_tx_skb(sk, ssk, info->data_lock_held);
+		if (!skb)
+			return -ENOMEM;
+
+		i = skb_shinfo(skb)->nr_frags;
+		reuse_skb = false;
+		mpext = skb_ext_find(skb, SKB_EXT_MPTCP);
+	}
 
 	/* Zero window and all data acked? Probe. */
-	avail_size = mptcp_check_allowed_size(msk, data_seq, avail_size);
-	if (avail_size == 0) {
+	copy = mptcp_check_allowed_size(msk, data_seq, copy);
+	if (copy == 0) {
 		u64 snd_una = READ_ONCE(msk->snd_una);
 
-		if (skb || snd_una != msk->snd_nxt)
+		if (snd_una != msk->snd_nxt || tcp_write_queue_tail(ssk)) {
+			tcp_remove_empty_skb(ssk);
 			return 0;
+		}
+
 		zero_window_probe = true;
 		data_seq = snd_una - 1;
-		avail_size = 1;
+		copy = 1;
 	}
 
-	if (WARN_ON_ONCE(info->sent > info->limit ||
-			 info->limit > dfrag->data_len))
-		return 0;
-
-	ret = info->limit - info->sent;
-	tail = tcp_build_frag(ssk, avail_size + size_bias, info->flags,
-			      dfrag->page, dfrag->offset + info->sent, &ret);
-	if (!tail) {
-		tcp_remove_empty_skb(sk, tcp_write_queue_tail(ssk));
+	copy = min_t(size_t, copy, info->limit - info->sent);
+	if (!sk_wmem_schedule(ssk, copy)) {
+		tcp_remove_empty_skb(ssk);
 		return -ENOMEM;
 	}
 
-	/* if the tail skb is still the cached one, collapsing really happened.
-	 */
-	if (skb == tail) {
-		TCP_SKB_CB(tail)->tcp_flags &= ~TCPHDR_PSH;
-		mpext->data_len += ret;
-		WARN_ON_ONCE(zero_window_probe);
-		goto out;
+	if (can_coalesce) {
+		skb_frag_size_add(&skb_shinfo(skb)->frags[i - 1], copy);
+	} else {
+		get_page(dfrag->page);
+		skb_fill_page_desc(skb, i, dfrag->page, offset, copy);
 	}
 
-	mpext = skb_ext_find(tail, SKB_EXT_MPTCP);
-	if (WARN_ON_ONCE(!mpext)) {
-		/* should never reach here, stream corrupted */
-		return -EINVAL;
+	skb->len += copy;
+	skb->data_len += copy;
+	skb->truesize += copy;
+	sk_wmem_queued_add(ssk, copy);
+	sk_mem_charge(ssk, copy);
+	skb->ip_summed = CHECKSUM_PARTIAL;
+	WRITE_ONCE(tcp_sk(ssk)->write_seq, tcp_sk(ssk)->write_seq + copy);
+	TCP_SKB_CB(skb)->end_seq += copy;
+	tcp_skb_pcount_set(skb, 0);
+
+	/* on skb reuse we just need to update the DSS len */
+	if (reuse_skb) {
+		TCP_SKB_CB(skb)->tcp_flags &= ~TCPHDR_PSH;
+		mpext->data_len += copy;
+		goto out;
 	}
 
 	memset(mpext, 0, sizeof(*mpext));
 	mpext->data_seq = data_seq;
 	mpext->subflow_seq = mptcp_subflow_ctx(ssk)->rel_write_seq;
-	mpext->data_len = ret;
+	mpext->data_len = copy;
 	mpext->use_map = 1;
 	mpext->dsn64 = 1;
 
-	pr_debug("data_seq=%llu subflow_seq=%u data_len=%u dsn64=%d",
+	pr_debug("data_seq=%llu subflow_seq=%u data_len=%u dsn64=%d\n",
 		 mpext->data_seq, mpext->subflow_seq, mpext->data_len,
 		 mpext->dsn64);
 
 	if (zero_window_probe) {
-		mptcp_subflow_ctx(ssk)->rel_write_seq += ret;
+		mptcp_subflow_ctx(ssk)->rel_write_seq += copy;
 		mpext->frozen = 1;
 		if (READ_ONCE(msk->csum_enabled))
-			mptcp_update_data_checksum(tail, ret);
+			mptcp_update_data_checksum(skb, copy);
 		tcp_push_pending_frames(ssk);
 		return 0;
 	}
 out:
 	if (READ_ONCE(msk->csum_enabled))
-		mptcp_update_data_checksum(tail, ret);
-	mptcp_subflow_ctx(ssk)->rel_write_seq += ret;
-	return ret;
+		mptcp_update_data_checksum(skb, copy);
+	mptcp_subflow_ctx(ssk)->rel_write_seq += copy;
+	return copy;
 }
 
 #define MPTCP_SEND_BURST_SIZE		((1 << 16) - \
@@ -1461,13 +1529,15 @@
 		send_info[i].ratio = -1;
 	}
 	mptcp_for_each_subflow(msk, subflow) {
+		bool backup = subflow->backup || subflow->request_bkup;
+
 		trace_mptcp_subflow_get_send(subflow);
 		ssk =  mptcp_subflow_tcp_sock(subflow);
 		if (!mptcp_subflow_active(subflow))
 			continue;
 
 		tout = max(tout, mptcp_timeout_from_subflow(subflow));
-		nr_active += !subflow->backup;
+		nr_active += !backup;
 		if (!sk_stream_memory_free(subflow->tcp_sock) || !tcp_sk(ssk)->snd_wnd)
 			continue;
 
@@ -1477,9 +1547,9 @@
 
 		ratio = div_u64((u64)READ_ONCE(ssk->sk_wmem_queued) << 32,
 				pace);
-		if (ratio < send_info[subflow->backup].ratio) {
-			send_info[subflow->backup].ssk = ssk;
-			send_info[subflow->backup].ratio = ratio;
+		if (ratio < send_info[backup].ratio) {
+			send_info[backup].ssk = ssk;
+			send_info[backup].ratio = ratio;
 		}
 	}
 	__mptcp_set_timeout(sk, tout);
@@ -1505,6 +1575,32 @@
 	release_sock(ssk);
 }
 
+static void mptcp_update_post_push(struct mptcp_sock *msk,
+				   struct mptcp_data_frag *dfrag,
+				   u32 sent)
+{
+	u64 snd_nxt_new = dfrag->data_seq;
+
+	dfrag->already_sent += sent;
+
+	msk->snd_burst -= sent;
+	msk->tx_pending_data -= sent;
+
+	snd_nxt_new += dfrag->already_sent;
+
+	/* snd_nxt_new can be smaller than snd_nxt in case mptcp
+	 * is recovering after a failover. In that event, this re-sends
+	 * old segments.
+	 *
+	 * Thus compute snd_nxt_new candidate based on
+	 * the dfrag->data_seq that was sent and the data
+	 * that has been handed to the subflow for transmission
+	 * and skip update in case it was old dfrag.
+	 */
+	if (likely(after64(snd_nxt_new, msk->snd_nxt)))
+		msk->snd_nxt = snd_nxt_new;
+}
+
 void __mptcp_push_pending(struct sock *sk, unsigned int flags)
 {
 	struct sock *prev_ssk = NULL, *ssk = NULL;
@@ -1523,7 +1619,7 @@
 			int ret = 0;
 
 			prev_ssk = ssk;
-			mptcp_flush_join_list(msk);
+			__mptcp_flush_join_list(msk);
 			ssk = mptcp_subflow_get_send(msk);
 
 			/* First check. If the ssk has changed since
@@ -1548,12 +1644,10 @@
 			}
 
 			info.sent += ret;
-			dfrag->already_sent += ret;
-			msk->snd_nxt += ret;
-			msk->snd_burst -= ret;
-			msk->tx_pending_data -= ret;
 			copied += ret;
 			len -= ret;
+
+			mptcp_update_post_push(msk, dfrag, ret);
 		}
 		WRITE_ONCE(msk->first_pending, mptcp_send_next(sk));
 	}
@@ -1564,10 +1658,10 @@
 
 out:
 	/* ensure the rtx timer is running */
-	if (!mptcp_timer_pending(sk))
-		mptcp_reset_timer(sk);
+	if (!mptcp_rtx_timer_pending(sk))
+		mptcp_reset_rtx_timer(sk);
 	if (copied)
-		__mptcp_check_send_data_fin(sk);
+		mptcp_check_send_data_fin(sk);
 }
 
 static void __mptcp_subflow_push_pending(struct sock *sk, struct sock *ssk)
@@ -1597,7 +1691,8 @@
 			if (!xmit_ssk)
 				goto out;
 			if (xmit_ssk != ssk) {
-				mptcp_subflow_delegate(mptcp_subflow_ctx(xmit_ssk));
+				mptcp_subflow_delegate(mptcp_subflow_ctx(xmit_ssk),
+						       MPTCP_DELEGATE_SEND);
 				goto out;
 			}
 
@@ -1606,13 +1701,11 @@
 				goto out;
 
 			info.sent += ret;
-			dfrag->already_sent += ret;
-			msk->snd_nxt += ret;
-			msk->snd_burst -= ret;
-			msk->tx_pending_data -= ret;
 			copied += ret;
 			len -= ret;
 			first = false;
+
+			mptcp_update_post_push(msk, dfrag, ret);
 		}
 		WRITE_ONCE(msk->first_pending, mptcp_send_next(sk));
 	}
@@ -1625,8 +1718,8 @@
 	if (copied) {
 		tcp_push(ssk, 0, info.mss_now, tcp_sk(ssk)->nonagle,
 			 info.size_goal);
-		if (!mptcp_timer_pending(sk))
-			mptcp_reset_timer(sk);
+		if (!mptcp_rtx_timer_pending(sk))
+			mptcp_reset_rtx_timer(sk);
 
 		if (msk->snd_data_fin_enable &&
 		    msk->snd_nxt + 1 == msk->write_seq)
@@ -1734,7 +1827,7 @@
 			if (!msk->first_pending)
 				WRITE_ONCE(msk->first_pending, dfrag);
 		}
-		pr_debug("msk=%p dfrag at seq=%llu len=%u sent=%u new=%d", msk,
+		pr_debug("msk=%p dfrag at seq=%llu len=%u sent=%u new=%d\n", msk,
 			 dfrag->data_seq, dfrag->data_len, dfrag->already_sent,
 			 !dfrag_collapsed);
 
@@ -1855,7 +1948,7 @@
 	if (msk->rcvq_space.copied <= msk->rcvq_space.space)
 		goto new_measure;
 
-	if (sock_net(sk)->ipv4.sysctl_tcp_moderate_rcvbuf &&
+	if (READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_moderate_rcvbuf) &&
 	    !(sk->sk_userlocks & SOCK_RCVBUF_LOCK)) {
 		int rcvmem, rcvbuf;
 		u64 rcvwin, grow;
@@ -1873,7 +1966,7 @@
 
 		do_div(rcvwin, advmss);
 		rcvbuf = min_t(u64, rcvwin * rcvmem,
-			       sock_net(sk)->ipv4.sysctl_tcp_rmem[2]);
+			       READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[2]));
 
 		if (rcvbuf > sk->sk_rcvbuf) {
 			u32 window_clamp;
@@ -1894,7 +1987,8 @@
 				slow = lock_sock_fast(ssk);
 				WRITE_ONCE(ssk->sk_rcvbuf, rcvbuf);
 				tcp_sk(ssk)->window_clamp = window_clamp;
-				tcp_cleanup_rbuf(ssk, 1);
+				if (tcp_can_send_ack(ssk))
+					tcp_cleanup_rbuf(ssk, 1);
 				unlock_sock_fast(ssk, slow);
 			}
 		}
@@ -2005,9 +2099,6 @@
 
 		copied += bytes_read;
 
-		/* be sure to advertise window change */
-		mptcp_cleanup_rbuf(msk);
-
 		if (skb_queue_empty(&msk->receive_queue) && __mptcp_move_skbs(msk))
 			continue;
 
@@ -2058,17 +2149,20 @@
 			}
 		}
 
-		pr_debug("block timeout %ld", timeo);
+		pr_debug("block timeout %ld\n", timeo);
+		mptcp_cleanup_rbuf(msk, copied);
 		sk_wait_data(sk, &timeo, NULL);
 	}
 
+	mptcp_cleanup_rbuf(msk, copied);
+
 out_err:
 	if (cmsg_flags && copied >= 0) {
 		if (cmsg_flags & MPTCP_CMSG_TS)
 			tcp_recv_timestamp(msg, sk, &tss);
 	}
 
-	pr_debug("msk=%p rx queue empty=%d:%d copied=%d",
+	pr_debug("msk=%p rx queue empty=%d:%d copied=%d\n",
 		 msk, skb_queue_empty_lockless(&sk->sk_receive_queue),
 		 skb_queue_empty(&msk->receive_queue), copied);
 	if (!(flags & MSG_PEEK))
@@ -2098,7 +2192,7 @@
 	sock_put(sk);
 }
 
-static void mptcp_timeout_timer(struct timer_list *t)
+static void mptcp_tout_timer(struct timer_list *t)
 {
 	struct sock *sk = from_timer(sk, t, sk_timer);
 
@@ -2135,7 +2229,7 @@
 			continue;
 		}
 
-		if (subflow->backup) {
+		if (subflow->backup || subflow->request_bkup) {
 			if (!backup)
 				backup = ssk;
 			continue;
@@ -2168,9 +2262,6 @@
 	if (__mptcp_check_fallback(mptcp_sk(sk)))
 		return false;
 
-	if (tcp_rtx_and_write_queues_empty(sk))
-		return false;
-
 	/* the closing socket has some data untransmitted and/or unacked:
 	 * some data in the mptcp rtx queue has not really xmitted yet.
 	 * keep it simple and re-inject the whole mptcp level rtx queue
@@ -2183,15 +2274,12 @@
 		return false;
 	}
 
-	/* will accept ack for reijected data before re-sending them */
-	if (!msk->recovery || after64(msk->snd_nxt, msk->recovery_snd_nxt))
-		msk->recovery_snd_nxt = msk->snd_nxt;
+	msk->recovery_snd_nxt = msk->snd_nxt;
 	msk->recovery = true;
 	mptcp_data_unlock(sk);
 
 	msk->first_pending = rtx_head;
 	msk->tx_pending_data += msk->snd_nxt - rtx_head->data_seq;
-	msk->snd_nxt = rtx_head->data_seq;
 	msk->snd_burst = 0;
 
 	/* be sure to clear the "sent status" on all re-injected fragments */
@@ -2244,6 +2332,7 @@
 		/* close acquired an extra ref */
 		__sock_put(ssk);
 	}
+	__mptcp_subflow_error_report(sk, ssk);
 	release_sock(ssk);
 
 	sock_put(ssk);
@@ -2264,6 +2353,12 @@
 void mptcp_close_ssk(struct sock *sk, struct sock *ssk,
 		     struct mptcp_subflow_context *subflow)
 {
+	/* The first subflow can already be closed and still in the list */
+	if (subflow->close_event_done)
+		return;
+
+	subflow->close_event_done = true;
+
 	if (sk->sk_state == TCP_ESTABLISHED)
 		mptcp_event(MPTCP_EVENT_SUB_CLOSED, mptcp_sk(sk), ssk, GFP_KERNEL);
 	__mptcp_close_ssk(sk, ssk, subflow);
@@ -2282,8 +2377,11 @@
 
 	list_for_each_entry_safe(subflow, tmp, &msk->conn_list, node) {
 		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
+		int ssk_state = inet_sk_state_load(ssk);
 
-		if (inet_sk_state_load(ssk) != TCP_CLOSE)
+		if (ssk_state != TCP_CLOSE &&
+		    (ssk_state != TCP_CLOSE_WAIT ||
+		     inet_sk_state_load((struct sock *)ssk) != TCP_ESTABLISHED))
 			continue;
 
 		/* 'subflow_data_ready' will re-sched once rx queue is empty */
@@ -2390,13 +2488,14 @@
 		dfrag->already_sent = max(dfrag->already_sent, info.sent);
 		tcp_push(ssk, 0, info.mss_now, tcp_sk(ssk)->nonagle,
 			 info.size_goal);
+		WRITE_ONCE(msk->allow_infinite_fallback, false);
 	}
 
 	release_sock(ssk);
 
 reset_timer:
-	if (!mptcp_timer_pending(sk))
-		mptcp_reset_timer(sk);
+	if (!mptcp_rtx_timer_pending(sk))
+		mptcp_reset_rtx_timer(sk);
 }
 
 static void mptcp_worker(struct work_struct *work)
@@ -2407,10 +2506,9 @@
 
 	lock_sock(sk);
 	state = sk->sk_state;
-	if (unlikely(state == TCP_CLOSE))
+	if (unlikely((1 << state) & (TCPF_CLOSE | TCPF_LISTEN)))
 		goto unlock;
 
-	mptcp_check_data_fin_ack(sk);
 	mptcp_flush_join_list(msk);
 
 	mptcp_check_fastclose(msk);
@@ -2421,7 +2519,8 @@
 	if (test_and_clear_bit(MPTCP_WORK_EOF, &msk->flags))
 		mptcp_check_for_eof(msk);
 
-	__mptcp_check_send_data_fin(sk);
+	mptcp_check_send_data_fin(sk);
+	mptcp_check_data_fin_ack(sk);
 	mptcp_check_data_fin(sk);
 
 	/* There is no point in keeping around an orphaned sk timedout or
@@ -2467,13 +2566,14 @@
 	msk->first = NULL;
 	inet_csk(sk)->icsk_sync_mss = mptcp_sync_mss;
 	WRITE_ONCE(msk->csum_enabled, mptcp_is_checksum_enabled(sock_net(sk)));
+	WRITE_ONCE(msk->allow_infinite_fallback, true);
 	msk->recovery = false;
 
 	mptcp_pm_data_init(msk);
 
 	/* re-use the csk retrans timer for MPTCP-level retrans */
 	timer_setup(&msk->sk.icsk_retransmit_timer, mptcp_retransmit_timer, 0);
-	timer_setup(&sk->sk_timer, mptcp_timeout_timer, 0);
+	timer_setup(&sk->sk_timer, mptcp_tout_timer, 0);
 
 	return 0;
 }
@@ -2509,8 +2609,8 @@
 	icsk->icsk_ca_ops = NULL;
 
 	sk_sockets_allocated_inc(sk);
-	sk->sk_rcvbuf = sock_net(sk)->ipv4.sysctl_tcp_rmem[1];
-	sk->sk_sndbuf = sock_net(sk)->ipv4.sysctl_tcp_wmem[1];
+	sk->sk_rcvbuf = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_rmem[1]);
+	sk->sk_sndbuf = READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_wmem[1]);
 
 	return 0;
 }
@@ -2547,14 +2647,20 @@
 		break;
 	default:
 		if (__mptcp_check_fallback(mptcp_sk(sk))) {
-			pr_debug("Fallback");
+			pr_debug("Fallback\n");
 			ssk->sk_shutdown |= how;
 			tcp_shutdown(ssk, how);
+
+			/* simulate the data_fin ack reception to let the state
+			 * machine move forward
+			 */
+			WRITE_ONCE(mptcp_sk(sk)->snd_una, mptcp_sk(sk)->snd_nxt);
+			mptcp_schedule_work(sk);
 		} else {
-			pr_debug("Sending DATA_FIN on subflow %p", ssk);
+			pr_debug("Sending DATA_FIN on subflow %p\n", ssk);
 			tcp_send_ack(ssk);
-			if (!mptcp_timer_pending(sk))
-				mptcp_reset_timer(sk);
+			if (!mptcp_rtx_timer_pending(sk))
+				mptcp_reset_rtx_timer(sk);
 		}
 		break;
 	}
@@ -2589,12 +2695,12 @@
 	return next & TCP_ACTION_FIN;
 }
 
-static void __mptcp_check_send_data_fin(struct sock *sk)
+static void mptcp_check_send_data_fin(struct sock *sk)
 {
 	struct mptcp_subflow_context *subflow;
 	struct mptcp_sock *msk = mptcp_sk(sk);
 
-	pr_debug("msk=%p snd_data_fin_enable=%d pending=%d snd_nxt=%llu write_seq=%llu",
+	pr_debug("msk=%p snd_data_fin_enable=%d pending=%d snd_nxt=%llu write_seq=%llu\n",
 		 msk, msk->snd_data_fin_enable, !!mptcp_send_head(sk),
 		 msk->snd_nxt, msk->write_seq);
 
@@ -2607,18 +2713,6 @@
 
 	WRITE_ONCE(msk->snd_nxt, msk->write_seq);
 
-	/* fallback socket will not get data_fin/ack, can move to the next
-	 * state now
-	 */
-	if (__mptcp_check_fallback(msk)) {
-		if ((1 << sk->sk_state) & (TCPF_CLOSING | TCPF_LAST_ACK)) {
-			inet_sk_state_store(sk, TCP_CLOSE);
-			mptcp_close_wake_up(sk);
-		} else if (sk->sk_state == TCP_FIN_WAIT1) {
-			inet_sk_state_store(sk, TCP_FIN_WAIT2);
-		}
-	}
-
 	mptcp_flush_join_list(msk);
 	mptcp_for_each_subflow(msk, subflow) {
 		struct sock *tcp_sk = mptcp_subflow_tcp_sock(subflow);
@@ -2631,7 +2725,7 @@
 {
 	struct mptcp_sock *msk = mptcp_sk(sk);
 
-	pr_debug("msk=%p snd_data_fin_enable=%d shutdown=%x state=%d pending=%d",
+	pr_debug("msk=%p snd_data_fin_enable=%d shutdown=%x state=%d pending=%d\n",
 		 msk, msk->snd_data_fin_enable, sk->sk_shutdown, sk->sk_state,
 		 !!mptcp_send_head(sk));
 
@@ -2639,7 +2733,7 @@
 	WRITE_ONCE(msk->write_seq, msk->write_seq + 1);
 	WRITE_ONCE(msk->snd_data_fin_enable, 1);
 
-	__mptcp_check_send_data_fin(sk);
+	mptcp_check_send_data_fin(sk);
 }
 
 static void __mptcp_destroy_sock(struct sock *sk)
@@ -2648,7 +2742,7 @@
 	struct mptcp_sock *msk = mptcp_sk(sk);
 	LIST_HEAD(conn_list);
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	might_sleep();
 
@@ -2685,6 +2779,7 @@
 {
 	struct mptcp_subflow_context *subflow;
 	bool do_cancel_work = false;
+	int subflows_alive = 0;
 
 	lock_sock(sk);
 	sk->sk_shutdown = SHUTDOWN_MASK;
@@ -2706,13 +2801,21 @@
 		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
 		bool slow = lock_sock_fast_nested(ssk);
 
+		subflows_alive += ssk->sk_state != TCP_CLOSE;
+
 		sock_orphan(ssk);
 		unlock_sock_fast(ssk, slow);
 	}
 	sock_orphan(sk);
 
+	/* all the subflows are closed, only timeout can change the msk
+	 * state, let's not keep resources busy for no reasons
+	 */
+	if (subflows_alive == 0)
+		inet_sk_state_store(sk, TCP_CLOSE);
+
 	sock_hold(sk);
-	pr_debug("msk=%p state=%d", sk, sk->sk_state);
+	pr_debug("msk=%p state=%d\n", sk, sk->sk_state);
 	if (sk->sk_state == TCP_CLOSE) {
 		__mptcp_destroy_sock(sk);
 		do_cancel_work = true;
@@ -2757,6 +2860,12 @@
 	struct mptcp_subflow_context *subflow;
 	struct mptcp_sock *msk = mptcp_sk(sk);
 
+	/* Deny disconnect if other threads are blocked in sk_wait_event()
+	 * or inet_wait_for_connect().
+	 */
+	if (sk->sk_wait_pending)
+		return -EBUSY;
+
 	mptcp_do_flush_join_list(msk);
 
 	mptcp_for_each_subflow(msk, subflow) {
@@ -2776,8 +2885,50 @@
 
 	return (struct ipv6_pinfo *)(((u8 *)sk) + offset);
 }
+
+static void mptcp_copy_ip6_options(struct sock *newsk, const struct sock *sk)
+{
+	const struct ipv6_pinfo *np = inet6_sk(sk);
+	struct ipv6_txoptions *opt;
+	struct ipv6_pinfo *newnp;
+
+	newnp = inet6_sk(newsk);
+
+	rcu_read_lock();
+	opt = rcu_dereference(np->opt);
+	if (opt) {
+		opt = ipv6_dup_options(newsk, opt);
+		if (!opt)
+			net_warn_ratelimited("%s: Failed to copy ip6 options\n", __func__);
+	}
+	RCU_INIT_POINTER(newnp->opt, opt);
+	rcu_read_unlock();
+}
 #endif
 
+static void mptcp_copy_ip_options(struct sock *newsk, const struct sock *sk)
+{
+	struct ip_options_rcu *inet_opt, *newopt = NULL;
+	const struct inet_sock *inet = inet_sk(sk);
+	struct inet_sock *newinet;
+
+	newinet = inet_sk(newsk);
+
+	rcu_read_lock();
+	inet_opt = rcu_dereference(inet->inet_opt);
+	if (inet_opt) {
+		newopt = sock_kmalloc(newsk, sizeof(*inet_opt) +
+				      inet_opt->opt.optlen, GFP_ATOMIC);
+		if (newopt)
+			memcpy(newopt, inet_opt, sizeof(*inet_opt) +
+			       inet_opt->opt.optlen);
+		else
+			net_warn_ratelimited("%s: Failed to copy ip options\n", __func__);
+	}
+	RCU_INIT_POINTER(newinet->inet_opt, newopt);
+	rcu_read_unlock();
+}
+
 struct sock *mptcp_sk_clone(const struct sock *sk,
 			    const struct mptcp_options_received *mp_opt,
 			    struct request_sock *req)
@@ -2795,8 +2946,16 @@
 		inet_sk(nsk)->pinet6 = mptcp_inet6_sk(nsk);
 #endif
 
+	nsk->sk_wait_pending = 0;
 	__mptcp_init_sock(nsk);
 
+#if IS_ENABLED(CONFIG_MPTCP_IPV6)
+	if (nsk->sk_family == AF_INET6)
+		mptcp_copy_ip6_options(nsk, sk);
+	else
+#endif
+		mptcp_copy_ip_options(nsk, sk);
+
 	msk = mptcp_sk(nsk);
 	msk->local_key = subflow_req->local_key;
 	msk->token = subflow_req->token;
@@ -2863,12 +3022,12 @@
 		return NULL;
 	}
 
-	pr_debug("msk=%p, listener=%p", msk, mptcp_subflow_ctx(listener->sk));
+	pr_debug("msk=%p, listener=%p\n", msk, mptcp_subflow_ctx(listener->sk));
 	newsk = inet_csk_accept(listener->sk, flags, err, kern);
 	if (!newsk)
 		return NULL;
 
-	pr_debug("msk=%p, subflow is mptcp=%d", msk, sk_is_mptcp(newsk));
+	pr_debug("msk=%p, subflow is mptcp=%d\n", msk, sk_is_mptcp(newsk));
 	if (sk_is_mptcp(newsk)) {
 		struct mptcp_subflow_context *subflow;
 		struct sock *new_mptcp_sock;
@@ -2881,18 +3040,17 @@
 		 */
 		if (WARN_ON_ONCE(!new_mptcp_sock)) {
 			tcp_sk(newsk)->is_mptcp = 0;
-			return newsk;
+			goto out;
 		}
 
 		/* acquire the 2nd reference for the owning socket */
 		sock_hold(new_mptcp_sock);
 		newsk = new_mptcp_sock;
 		MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_MPCAPABLEPASSIVEACK);
-	} else {
-		MPTCP_INC_STATS(sock_net(sk),
-				MPTCP_MIB_MPCAPABLEPASSIVEFALLBACK);
 	}
 
+out:
+	newsk->sk_kern_sock = kern;
 	return newsk;
 }
 
@@ -2940,7 +3098,7 @@
 		if (xmit_ssk == ssk)
 			__mptcp_subflow_push_pending(sk, ssk);
 		else if (xmit_ssk)
-			mptcp_subflow_delegate(mptcp_subflow_ctx(xmit_ssk));
+			mptcp_subflow_delegate(mptcp_subflow_ctx(xmit_ssk), MPTCP_DELEGATE_SEND);
 	} else {
 		set_bit(MPTCP_PUSH_PENDING, &mptcp_sk(sk)->flags);
 	}
@@ -2994,18 +3152,50 @@
 	__mptcp_update_rmem(sk);
 }
 
+/* MP_JOIN client subflow must wait for 4th ack before sending any data:
+ * TCP can't schedule delack timer before the subflow is fully established.
+ * MPTCP uses the delack timer to do 3rd ack retransmissions
+ */
+static void schedule_3rdack_retransmission(struct sock *ssk)
+{
+	struct inet_connection_sock *icsk = inet_csk(ssk);
+	struct tcp_sock *tp = tcp_sk(ssk);
+	unsigned long timeout;
+
+	if (mptcp_subflow_ctx(ssk)->fully_established)
+		return;
+
+	/* reschedule with a timeout above RTT, as we must look only for drop */
+	if (tp->srtt_us)
+		timeout = usecs_to_jiffies(tp->srtt_us >> (3 - 1));
+	else
+		timeout = TCP_TIMEOUT_INIT;
+	timeout += jiffies;
+
+	WARN_ON_ONCE(icsk->icsk_ack.pending & ICSK_ACK_TIMER);
+	icsk->icsk_ack.pending |= ICSK_ACK_SCHED | ICSK_ACK_TIMER;
+	icsk->icsk_ack.timeout = timeout;
+	sk_reset_timer(ssk, &icsk->icsk_delack_timer, timeout);
+}
+
 void mptcp_subflow_process_delegated(struct sock *ssk)
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(ssk);
 	struct sock *sk = subflow->conn;
 
-	mptcp_data_lock(sk);
-	if (!sock_owned_by_user(sk))
-		__mptcp_subflow_push_pending(sk, ssk);
-	else
-		set_bit(MPTCP_PUSH_PENDING, &mptcp_sk(sk)->flags);
-	mptcp_data_unlock(sk);
-	mptcp_subflow_delegated_done(subflow);
+	if (test_bit(MPTCP_DELEGATE_SEND, &subflow->delegated_status)) {
+		mptcp_data_lock(sk);
+		if (!sock_owned_by_user(sk))
+			__mptcp_subflow_push_pending(sk, ssk);
+		else
+			set_bit(MPTCP_PUSH_PENDING, &mptcp_sk(sk)->flags);
+		mptcp_data_unlock(sk);
+		mptcp_subflow_delegated_done(subflow, MPTCP_DELEGATE_SEND);
+	}
+	if (test_bit(MPTCP_DELEGATE_ACK, &subflow->delegated_status)) {
+		schedule_3rdack_retransmission(ssk);
+		mptcp_subflow_delegated_done(subflow, MPTCP_DELEGATE_ACK);
+	}
 }
 
 static int mptcp_hash(struct sock *sk)
@@ -3028,7 +3218,7 @@
 	struct socket *ssock;
 
 	ssock = __mptcp_nmpc_socket(msk);
-	pr_debug("msk=%p, subflow=%p", msk, ssock);
+	pr_debug("msk=%p, subflow=%p\n", msk, ssock);
 	if (WARN_ON_ONCE(!ssock))
 		return -EINVAL;
 
@@ -3046,7 +3236,7 @@
 	sk = subflow->conn;
 	msk = mptcp_sk(sk);
 
-	pr_debug("msk=%p, token=%u", sk, subflow->token);
+	pr_debug("msk=%p, token=%u\n", sk, subflow->token);
 
 	mptcp_crypto_key_sha(subflow->remote_key, NULL, &ack_seq);
 	ack_seq++;
@@ -3087,7 +3277,7 @@
 	struct socket *parent_sock;
 	bool ret;
 
-	pr_debug("msk=%p, subflow=%p", msk, subflow);
+	pr_debug("msk=%p, subflow=%p\n", msk, subflow);
 
 	/* mptcp socket already closing? */
 	if (!mptcp_is_fully_established(parent)) {
@@ -3127,6 +3317,7 @@
 	if (parent_sock && !ssk->sk_socket)
 		mptcp_sock_graft(ssk, parent_sock);
 	subflow->map_seq = READ_ONCE(msk->ack_seq);
+	WRITE_ONCE(msk->allow_infinite_fallback, false);
 out:
 	mptcp_event(MPTCP_EVENT_SUB_ESTABLISHED, msk, ssk, GFP_ATOMIC);
 	return true;
@@ -3134,7 +3325,7 @@
 
 static void mptcp_shutdown(struct sock *sk, int how)
 {
-	pr_debug("sk=%p, how=%d", sk, how);
+	pr_debug("sk=%p, how=%d\n", sk, how);
 
 	if ((how & SEND_SHUTDOWN) && mptcp_close_state(sk))
 		__mptcp_wr_shutdown(sk);
@@ -3234,6 +3425,10 @@
 		MPTCP_INC_STATS(sock_net(ssock->sk), MPTCP_MIB_TOKENFALLBACKINIT);
 		mptcp_subflow_early_fallback(msk, subflow);
 	}
+
+	WRITE_ONCE(msk->write_seq, subflow->idsn);
+	WRITE_ONCE(msk->snd_nxt, subflow->idsn);
+	WRITE_ONCE(msk->snd_una, subflow->idsn);
 	if (likely(!__mptcp_check_fallback(msk)))
 		MPTCP_INC_STATS(sock_net(sock->sk), MPTCP_MIB_MPCAPABLEACTIVE);
 
@@ -3260,7 +3455,7 @@
 	struct socket *ssock;
 	int err;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	lock_sock(sock->sk);
 	ssock = __mptcp_nmpc_socket(msk);
@@ -3290,7 +3485,7 @@
 	struct socket *ssock;
 	int err;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	lock_sock(sock->sk);
 	if (sock->sk->sk_state != TCP_LISTEN)
@@ -3394,7 +3589,7 @@
 	sock_poll_wait(file, sock, wait);
 
 	state = inet_sk_state_load(sk);
-	pr_debug("msk=%p state=%d flags=%lx", msk, state, msk->flags);
+	pr_debug("msk=%p state=%d flags=%lx\n", msk, state, msk->flags);
 	if (state == TCP_LISTEN)
 		return test_bit(MPTCP_DATA_READY, &msk->flags) ? EPOLLIN | EPOLLRDNORM : 0;
 
@@ -3537,12 +3732,6 @@
 
 static struct proto mptcp_v6_prot;
 
-static void mptcp_v6_destroy(struct sock *sk)
-{
-	mptcp_destroy(sk);
-	inet6_destroy_sock(sk);
-}
-
 static struct inet_protosw mptcp_v6_protosw = {
 	.type		= SOCK_STREAM,
 	.protocol	= IPPROTO_MPTCP,
@@ -3558,7 +3747,6 @@
 	mptcp_v6_prot = mptcp_prot;
 	strcpy(mptcp_v6_prot.name, "MPTCPv6");
 	mptcp_v6_prot.slab = NULL;
-	mptcp_v6_prot.destroy = mptcp_v6_destroy;
 	mptcp_v6_prot.obj_size = sizeof(struct mptcp6_sock);
 
 	err = proto_register(&mptcp_v6_prot, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/protocol.h
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/protocol.h
@@ -139,22 +139,24 @@
 	u32	subflow_seq;
 	u16	data_len;
 	__sum16	csum;
-	u16	suboptions;
+	struct_group(status,
+		u16 suboptions;
+		u16 use_map:1,
+		    dsn64:1,
+		    data_fin:1,
+		    use_ack:1,
+		    ack64:1,
+		    mpc_map:1,
+		    reset_reason:4,
+		    reset_transient:1,
+		    echo:1,
+		    backup:1,
+		    deny_join_id0:1,
+		    __unused:2;
+	);
+	u8	join_id;
 	u32	token;
 	u32	nonce;
-	u16	use_map:1,
-		dsn64:1,
-		data_fin:1,
-		use_ack:1,
-		ack64:1,
-		mpc_map:1,
-		reset_reason:4,
-		reset_transient:1,
-		echo:1,
-		backup:1,
-		deny_join_id0:1,
-		__unused:2;
-	u8	join_id;
 	u64	thmac;
 	u8	hmac[MPTCPOPT_HMAC_LEN];
 	struct mptcp_addr_info addr;
@@ -249,7 +251,11 @@
 	bool		rcv_fastclose;
 	bool		use_64bit_ack; /* Set when we received a 64-bit DSN */
 	bool		csum_enabled;
+	bool		allow_infinite_fallback;
 	spinlock_t	join_list_lock;
+	int		keepalive_cnt;
+	int		keepalive_idle;
+	int		keepalive_intvl;
 	struct work_struct work;
 	struct sk_buff  *ooo_last_skb;
 	struct rb_root  out_of_order_queue;
@@ -367,6 +373,7 @@
 	u16	mp_capable : 1,
 		mp_join : 1,
 		backup : 1,
+		request_bkup : 1,
 		csum_reqd : 1,
 		allow_join_id0 : 1;
 	u8	local_id;
@@ -401,6 +408,7 @@
 DECLARE_PER_CPU(struct mptcp_delegated_action, mptcp_delegated_actions);
 
 #define MPTCP_DELEGATE_SEND		0
+#define MPTCP_DELEGATE_ACK		1
 
 /* MPTCP subflow context */
 struct mptcp_subflow_context {
@@ -435,8 +443,12 @@
 		rx_eof : 1,
 		can_ack : 1,        /* only after processing the remote a key */
 		disposable : 1,	    /* ctx can be free at ulp release time */
-		stale : 1;	    /* unable to snd/rcv data, do not use for xmit */
+		stale : 1,	    /* unable to snd/rcv data, do not use for xmit */
+		valid_csum_seen : 1,        /* at least one csum validated */
+		close_event_done : 1,       /* has done the post-closed part */
+		__unused : 11;
 	enum mptcp_data_avail data_avail;
+	bool	pm_listener;	    /* a listener managed by the kernel PM? */
 	u32	remote_nonce;
 	u64	thmac;
 	u32	local_nonce;
@@ -506,23 +518,23 @@
 
 void mptcp_subflow_process_delegated(struct sock *ssk);
 
-static inline void mptcp_subflow_delegate(struct mptcp_subflow_context *subflow)
+static inline void mptcp_subflow_delegate(struct mptcp_subflow_context *subflow, int action)
 {
 	struct mptcp_delegated_action *delegated;
 	bool schedule;
 
+	/* the caller held the subflow bh socket lock */
+	lockdep_assert_in_softirq();
+
 	/* The implied barrier pairs with mptcp_subflow_delegated_done(), and
 	 * ensures the below list check sees list updates done prior to status
 	 * bit changes
 	 */
-	if (!test_and_set_bit(MPTCP_DELEGATE_SEND, &subflow->delegated_status)) {
+	if (!test_and_set_bit(action, &subflow->delegated_status)) {
 		/* still on delegated list from previous scheduling */
 		if (!list_empty(&subflow->delegated_node))
 			return;
 
-		/* the caller held the subflow bh socket lock */
-		lockdep_assert_in_softirq();
-
 		delegated = this_cpu_ptr(&mptcp_delegated_actions);
 		schedule = list_empty(&delegated->head);
 		list_add_tail(&subflow->delegated_node, &delegated->head);
@@ -547,16 +559,16 @@
 
 static inline bool mptcp_subflow_has_delegated_action(const struct mptcp_subflow_context *subflow)
 {
-	return test_bit(MPTCP_DELEGATE_SEND, &subflow->delegated_status);
+	return !!READ_ONCE(subflow->delegated_status);
 }
 
-static inline void mptcp_subflow_delegated_done(struct mptcp_subflow_context *subflow)
+static inline void mptcp_subflow_delegated_done(struct mptcp_subflow_context *subflow, int action)
 {
 	/* pairs with mptcp_subflow_delegate, ensures delegate_node is updated before
 	 * touching the status bit
 	 */
 	smp_wmb();
-	clear_bit(MPTCP_DELEGATE_SEND, &subflow->delegated_status);
+	clear_bit(action, &subflow->delegated_status);
 }
 
 int mptcp_is_enabled(const struct net *net);
@@ -577,6 +589,7 @@
 void mptcp_subflow_reset(struct sock *ssk);
 void mptcp_sock_graft(struct sock *sk, struct socket *parent);
 struct socket *__mptcp_nmpc_socket(const struct mptcp_sock *msk);
+void mptcp_local_address(const struct sock_common *skc, struct mptcp_addr_info *addr);
 
 /* called with sk socket lock held */
 int __mptcp_subflow_connect(struct sock *sk, const struct mptcp_addr_info *loc,
@@ -634,8 +647,7 @@
 struct sock *mptcp_sk_clone(const struct sock *sk,
 			    const struct mptcp_options_received *mp_opt,
 			    struct request_sock *req);
-void mptcp_get_options(const struct sock *sk,
-		       const struct sk_buff *skb,
+void mptcp_get_options(const struct sk_buff *skb,
 		       struct mptcp_options_received *mp_opt);
 
 void mptcp_finish_connect(struct sock *sk);
@@ -717,6 +729,7 @@
 void mptcp_crypto_key_sha(u64 key, u32 *token, u64 *idsn);
 
 void mptcp_crypto_hmac_sha(u64 key1, u64 key2, u8 *msg, int len, void *hmac);
+__sum16 __mptcp_make_csum(u64 data_seq, u32 subflow_seq, u16 data_len, __wsum sum);
 
 void __init mptcp_pm_init(void);
 void mptcp_pm_data_init(struct mptcp_sock *msk);
@@ -731,8 +744,10 @@
 void mptcp_pm_add_addr_received(struct mptcp_sock *msk,
 				const struct mptcp_addr_info *addr);
 void mptcp_pm_add_addr_echoed(struct mptcp_sock *msk,
-			      struct mptcp_addr_info *addr);
+			      const struct mptcp_addr_info *addr);
 void mptcp_pm_add_addr_send_ack(struct mptcp_sock *msk);
+bool mptcp_pm_nl_is_init_remote_addr(struct mptcp_sock *msk,
+				     const struct mptcp_addr_info *remote);
 void mptcp_pm_nl_addr_send_ack(struct mptcp_sock *msk);
 void mptcp_pm_rm_addr_received(struct mptcp_sock *msk,
 			       const struct mptcp_rm_list *rm_list);
@@ -745,10 +760,10 @@
 bool mptcp_pm_sport_in_anno_list(struct mptcp_sock *msk, const struct sock *sk);
 struct mptcp_pm_add_entry *
 mptcp_pm_del_add_timer(struct mptcp_sock *msk,
-		       struct mptcp_addr_info *addr, bool check_id);
+		       const struct mptcp_addr_info *addr, bool check_id);
 struct mptcp_pm_add_entry *
-mptcp_lookup_anno_list_by_saddr(struct mptcp_sock *msk,
-				struct mptcp_addr_info *addr);
+mptcp_lookup_anno_list_by_saddr(const struct mptcp_sock *msk,
+				const struct mptcp_addr_info *addr);
 int mptcp_pm_get_flags_and_ifindex_by_id(struct net *net, unsigned int id,
 					 u8 *flags, int *ifindex);
 
@@ -807,13 +822,14 @@
 	return TCPOLEN_MPTCP_RM_ADDR_BASE + roundup(rm_list->nr - 1, 4) + 1;
 }
 
-bool mptcp_pm_add_addr_signal(struct mptcp_sock *msk, struct sk_buff *skb,
+bool mptcp_pm_add_addr_signal(struct mptcp_sock *msk, const struct sk_buff *skb,
 			      unsigned int opt_size, unsigned int remaining,
 			      struct mptcp_addr_info *addr, bool *echo,
-			      bool *port, bool *drop_other_suboptions);
+			      bool *drop_other_suboptions);
 bool mptcp_pm_rm_addr_signal(struct mptcp_sock *msk, unsigned int remaining,
 			     struct mptcp_rm_list *rm_list);
 int mptcp_pm_get_local_id(struct mptcp_sock *msk, struct sock_common *skc);
+bool mptcp_pm_is_backup(struct mptcp_sock *msk, struct sock_common *skc);
 
 void __init mptcp_pm_nl_init(void);
 void mptcp_pm_nl_data_init(struct mptcp_sock *msk);
@@ -821,10 +837,11 @@
 void mptcp_pm_nl_rm_subflow_received(struct mptcp_sock *msk,
 				     const struct mptcp_rm_list *rm_list);
 int mptcp_pm_nl_get_local_id(struct mptcp_sock *msk, struct sock_common *skc);
-unsigned int mptcp_pm_get_add_addr_signal_max(struct mptcp_sock *msk);
-unsigned int mptcp_pm_get_add_addr_accept_max(struct mptcp_sock *msk);
-unsigned int mptcp_pm_get_subflows_max(struct mptcp_sock *msk);
-unsigned int mptcp_pm_get_local_addr_max(struct mptcp_sock *msk);
+bool mptcp_pm_nl_is_backup(struct mptcp_sock *msk, struct mptcp_addr_info *skc);
+unsigned int mptcp_pm_get_add_addr_signal_max(const struct mptcp_sock *msk);
+unsigned int mptcp_pm_get_add_addr_accept_max(const struct mptcp_sock *msk);
+unsigned int mptcp_pm_get_subflows_max(const struct mptcp_sock *msk);
+unsigned int mptcp_pm_get_local_addr_max(const struct mptcp_sock *msk);
 
 void mptcp_sockopt_sync(struct mptcp_sock *msk, struct sock *ssk);
 void mptcp_sockopt_sync_all(struct mptcp_sock *msk);
@@ -852,9 +869,11 @@
 static inline void __mptcp_do_fallback(struct mptcp_sock *msk)
 {
 	if (test_bit(MPTCP_FALLBACK_DONE, &msk->flags)) {
-		pr_debug("TCP fallback already done (msk=%p)", msk);
+		pr_debug("TCP fallback already done (msk=%p)\n", msk);
 		return;
 	}
+	if (WARN_ON_ONCE(!READ_ONCE(msk->allow_infinite_fallback)))
+		return;
 	set_bit(MPTCP_FALLBACK_DONE, &msk->flags);
 }
 
@@ -866,7 +885,7 @@
 	__mptcp_do_fallback(msk);
 }
 
-#define pr_fallback(a) pr_debug("%s:fallback to TCP (msk=%p)", __func__, a)
+#define pr_fallback(a) pr_debug("%s:fallback to TCP (msk=%p)\n", __func__, a)
 
 static inline bool subflow_simultaneous_connect(struct sock *sk)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/sockopt.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/sockopt.c
@@ -177,8 +177,6 @@
 
 	switch (optname) {
 	case SO_KEEPALIVE:
-		mptcp_sol_socket_sync_intval(msk, optname, val);
-		return 0;
 	case SO_DEBUG:
 	case SO_MARK:
 	case SO_PRIORITY:
@@ -523,7 +521,6 @@
 		case TCP_NODELAY:
 		case TCP_THIN_LINEAR_TIMEOUTS:
 		case TCP_CONGESTION:
-		case TCP_ULP:
 		case TCP_CORK:
 		case TCP_KEEPIDLE:
 		case TCP_KEEPINTVL:
@@ -596,6 +593,60 @@
 	return ret;
 }
 
+static int __tcp_sock_set_keepintvl(struct sock *sk, int val)
+{
+	if (val < 1 || val > MAX_TCP_KEEPINTVL)
+		return -EINVAL;
+
+	WRITE_ONCE(tcp_sk(sk)->keepalive_intvl, val * HZ);
+
+	return 0;
+}
+
+static int __tcp_sock_set_keepcnt(struct sock *sk, int val)
+{
+	if (val < 1 || val > MAX_TCP_KEEPCNT)
+		return -EINVAL;
+
+	/* Paired with READ_ONCE() in keepalive_probes() */
+	WRITE_ONCE(tcp_sk(sk)->keepalive_probes, val);
+
+	return 0;
+}
+
+static int mptcp_setsockopt_set_val(struct mptcp_sock *msk, int max,
+				    int (*set_val)(struct sock *, int),
+				    int *msk_val, sockptr_t optval,
+				    unsigned int optlen)
+{
+	struct mptcp_subflow_context *subflow;
+	struct sock *sk = (struct sock *)msk;
+	int val, err;
+
+	err = mptcp_get_int_option(msk, optval, optlen, &val);
+	if (err)
+		return err;
+
+	lock_sock(sk);
+	mptcp_for_each_subflow(msk, subflow) {
+		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
+		int ret;
+
+		lock_sock(ssk);
+		ret = set_val(ssk, val);
+		err = err ? : ret;
+		release_sock(ssk);
+	}
+
+	if (!err) {
+		*msk_val = val;
+		sockopt_seq_inc(msk);
+	}
+	release_sock(sk);
+
+	return err;
+}
+
 static int mptcp_setsockopt_sol_tcp(struct mptcp_sock *msk, int optname,
 				    sockptr_t optval, unsigned int optlen)
 {
@@ -604,6 +655,21 @@
 		return -EOPNOTSUPP;
 	case TCP_CONGESTION:
 		return mptcp_setsockopt_sol_tcp_congestion(msk, optval, optlen);
+	case TCP_KEEPIDLE:
+		return mptcp_setsockopt_set_val(msk, MAX_TCP_KEEPIDLE,
+						&tcp_sock_set_keepidle_locked,
+						&msk->keepalive_idle,
+						optval, optlen);
+	case TCP_KEEPINTVL:
+		return mptcp_setsockopt_set_val(msk, MAX_TCP_KEEPINTVL,
+						&__tcp_sock_set_keepintvl,
+						&msk->keepalive_intvl,
+						optval, optlen);
+	case TCP_KEEPCNT:
+		return mptcp_setsockopt_set_val(msk, MAX_TCP_KEEPCNT,
+						&__tcp_sock_set_keepcnt,
+						&msk->keepalive_cnt,
+						optval, optlen);
 	}
 
 	return -EOPNOTSUPP;
@@ -615,7 +681,7 @@
 	struct mptcp_sock *msk = mptcp_sk(sk);
 	struct sock *ssk;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	if (level == SOL_SOCKET)
 		return mptcp_setsockopt_sol_socket(msk, optname, optval, optlen);
@@ -670,9 +736,40 @@
 	return ret;
 }
 
+static int mptcp_put_int_option(struct mptcp_sock *msk, char __user *optval,
+				int __user *optlen, int val)
+{
+	int len;
+
+	if (get_user(len, optlen))
+		return -EFAULT;
+	if (len < 0)
+		return -EINVAL;
+
+	if (len < sizeof(int) && len > 0 && val >= 0 && val <= 255) {
+		unsigned char ucval = (unsigned char)val;
+
+		len = 1;
+		if (put_user(len, optlen))
+			return -EFAULT;
+		if (copy_to_user(optval, &ucval, 1))
+			return -EFAULT;
+	} else {
+		len = min_t(unsigned int, len, sizeof(int));
+		if (put_user(len, optlen))
+			return -EFAULT;
+		if (copy_to_user(optval, &val, len))
+			return -EFAULT;
+	}
+
+	return 0;
+}
+
 static int mptcp_getsockopt_sol_tcp(struct mptcp_sock *msk, int optname,
 				    char __user *optval, int __user *optlen)
 {
+	struct sock *sk = (void *)msk;
+
 	switch (optname) {
 	case TCP_ULP:
 	case TCP_CONGESTION:
@@ -680,6 +777,18 @@
 	case TCP_CC_INFO:
 		return mptcp_getsockopt_first_sf_only(msk, SOL_TCP, optname,
 						      optval, optlen);
+	case TCP_KEEPIDLE:
+		return mptcp_put_int_option(msk, optval, optlen,
+					    msk->keepalive_idle ? :
+					    READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_keepalive_time) / HZ);
+	case TCP_KEEPINTVL:
+		return mptcp_put_int_option(msk, optval, optlen,
+					    msk->keepalive_intvl ? :
+					    READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_keepalive_intvl) / HZ);
+	case TCP_KEEPCNT:
+		return mptcp_put_int_option(msk, optval, optlen,
+					    msk->keepalive_cnt ? :
+					    READ_ONCE(sock_net(sk)->ipv4.sysctl_tcp_keepalive_probes));
 	}
 	return -EOPNOTSUPP;
 }
@@ -690,7 +799,7 @@
 	struct mptcp_sock *msk = mptcp_sk(sk);
 	struct sock *ssk;
 
-	pr_debug("msk=%p", msk);
+	pr_debug("msk=%p\n", msk);
 
 	/* @@ the meaning of setsockopt() when the socket is connected and
 	 * there are multiple subflows is not yet defined. It is up to the
@@ -749,6 +858,9 @@
 
 	if (inet_csk(sk)->icsk_ca_ops != inet_csk(ssk)->icsk_ca_ops)
 		tcp_set_congestion_control(ssk, msk->ca_name, false, true);
+	tcp_sock_set_keepidle_locked(ssk, msk->keepalive_idle);
+	__tcp_sock_set_keepintvl(ssk, msk->keepalive_intvl);
+	__tcp_sock_set_keepcnt(ssk, msk->keepalive_cnt);
 }
 
 static void __mptcp_sockopt_sync(struct mptcp_sock *msk, struct sock *ssk)
--- linux-xilinx-zynqmp-5.15.0.orig/net/mptcp/subflow.c
+++ linux-xilinx-zynqmp-5.15.0/net/mptcp/subflow.c
@@ -39,13 +39,12 @@
 {
 	struct mptcp_subflow_request_sock *subflow_req = mptcp_subflow_rsk(req);
 
-	pr_debug("subflow_req=%p", subflow_req);
+	pr_debug("subflow_req=%p\n", subflow_req);
 
 	if (subflow_req->msk)
 		sock_put((struct sock *)subflow_req->msk);
 
 	mptcp_token_destroy_request(req);
-	tcp_request_sock_ops.destructor(req);
 }
 
 static void subflow_generate_hmac(u64 key1, u64 key2, u32 nonce1, u32 nonce2,
@@ -98,6 +97,7 @@
 		return NULL;
 	}
 	subflow_req->local_id = local_id;
+	subflow_req->request_bkup = mptcp_pm_is_backup(msk, (struct sock_common *)req);
 
 	return msk;
 }
@@ -129,6 +129,13 @@
 	}
 }
 
+static int subflow_reset_req_endp(struct request_sock *req, struct sk_buff *skb)
+{
+	SUBFLOW_REQ_INC_STATS(req, MPTCP_MIB_MPCAPABLEENDPATTEMPT);
+	subflow_add_reset_reason(skb, MPTCP_RST_EPROHIBIT);
+	return -EPERM;
+}
+
 /* Init mptcp request socket.
  *
  * Returns an error code if a JOIN has failed and a TCP reset
@@ -143,7 +150,7 @@
 	struct mptcp_options_received mp_opt;
 	bool opt_mp_capable, opt_mp_join;
 
-	pr_debug("subflow_req=%p, listener=%p", subflow_req, listener);
+	pr_debug("subflow_req=%p, listener=%p\n", subflow_req, listener);
 
 #ifdef CONFIG_TCP_MD5SIG
 	/* no MPTCP if MD5SIG is enabled on this socket or we may run out of
@@ -153,17 +160,24 @@
 		return -EINVAL;
 #endif
 
-	mptcp_get_options(sk_listener, skb, &mp_opt);
+	mptcp_get_options(skb, &mp_opt);
 
 	opt_mp_capable = !!(mp_opt.suboptions & OPTIONS_MPTCP_MPC);
-	opt_mp_join = !!(mp_opt.suboptions & OPTIONS_MPTCP_MPJ);
+	opt_mp_join = !!(mp_opt.suboptions & OPTION_MPTCP_MPJ_SYN);
 	if (opt_mp_capable) {
 		SUBFLOW_REQ_INC_STATS(req, MPTCP_MIB_MPCAPABLEPASSIVE);
 
+		if (unlikely(listener->pm_listener))
+			return subflow_reset_req_endp(req, skb);
 		if (opt_mp_join)
 			return 0;
 	} else if (opt_mp_join) {
 		SUBFLOW_REQ_INC_STATS(req, MPTCP_MIB_JOINSYNRX);
+
+		if (mp_opt.backup)
+			SUBFLOW_REQ_INC_STATS(req, MPTCP_MIB_JOINSYNBACKUPRX);
+	} else if (unlikely(listener->pm_listener)) {
+		return subflow_reset_req_endp(req, skb);
 	}
 
 	if (opt_mp_capable && listener->request_mptcp) {
@@ -213,7 +227,7 @@
 		}
 
 		if (subflow_use_different_sport(subflow_req->msk, sk_listener)) {
-			pr_debug("syn inet_sport=%d %d",
+			pr_debug("syn inet_sport=%d %d\n",
 				 ntohs(inet_sk(sk_listener)->inet_sport),
 				 ntohs(inet_sk((struct sock *)subflow_req->msk)->inet_sport));
 			if (!mptcp_pm_sport_in_anno_list(subflow_req->msk, sk_listener)) {
@@ -232,7 +246,7 @@
 				return -EPERM;
 		}
 
-		pr_debug("token=%u, remote_nonce=%u msk=%p", subflow_req->token,
+		pr_debug("token=%u, remote_nonce=%u msk=%p\n", subflow_req->token,
 			 subflow_req->remote_nonce, subflow_req->msk);
 	}
 
@@ -250,10 +264,10 @@
 	int err;
 
 	subflow_init_req(req, sk_listener);
-	mptcp_get_options(sk_listener, skb, &mp_opt);
+	mptcp_get_options(skb, &mp_opt);
 
 	opt_mp_capable = !!(mp_opt.suboptions & OPTIONS_MPTCP_MPC);
-	opt_mp_join = !!(mp_opt.suboptions & OPTIONS_MPTCP_MPJ);
+	opt_mp_join = !!(mp_opt.suboptions & OPTION_MPTCP_MPJ_ACK);
 	if (opt_mp_capable && opt_mp_join)
 		return -EINVAL;
 
@@ -359,12 +373,10 @@
 	/* must hold: tcp_done() could drop last reference on parent */
 	sock_hold(sk);
 
-	tcp_set_state(ssk, TCP_CLOSE);
 	tcp_send_active_reset(ssk, GFP_ATOMIC);
 	tcp_done(ssk);
-	if (!test_and_set_bit(MPTCP_WORK_CLOSE_SUBFLOW, &mptcp_sk(sk)->flags) &&
-	    schedule_work(&mptcp_sk(sk)->work))
-		return; /* worker will put sk for us */
+	if (!test_and_set_bit(MPTCP_WORK_CLOSE_SUBFLOW, &mptcp_sk(sk)->flags))
+		mptcp_schedule_work(sk);
 
 	sock_put(sk);
 }
@@ -408,9 +420,9 @@
 	subflow->rel_write_seq = 1;
 	subflow->conn_finished = 1;
 	subflow->ssn_offset = TCP_SKB_CB(skb)->seq;
-	pr_debug("subflow=%p synack seq=%x", subflow, subflow->ssn_offset);
+	pr_debug("subflow=%p synack seq=%x\n", subflow, subflow->ssn_offset);
 
-	mptcp_get_options(sk, skb, &mp_opt);
+	mptcp_get_options(skb, &mp_opt);
 	if (subflow->request_mptcp) {
 		if (!(mp_opt.suboptions & OPTIONS_MPTCP_MPC)) {
 			MPTCP_INC_STATS(sock_net(sk),
@@ -427,7 +439,7 @@
 		subflow->mp_capable = 1;
 		subflow->can_ack = 1;
 		subflow->remote_key = mp_opt.sndr_key;
-		pr_debug("subflow=%p, remote_key=%llu", subflow,
+		pr_debug("subflow=%p, remote_key=%llu\n", subflow,
 			 subflow->remote_key);
 		MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_MPCAPABLEACTIVEACK);
 		mptcp_finish_connect(sk);
@@ -435,7 +447,7 @@
 	} else if (subflow->request_join) {
 		u8 hmac[SHA256_DIGEST_SIZE];
 
-		if (!(mp_opt.suboptions & OPTIONS_MPTCP_MPJ)) {
+		if (!(mp_opt.suboptions & OPTION_MPTCP_MPJ_SYNACK)) {
 			subflow->reset_reason = MPTCP_RST_EMPTCP;
 			goto do_reset;
 		}
@@ -443,7 +455,7 @@
 		subflow->backup = mp_opt.backup;
 		subflow->thmac = mp_opt.thmac;
 		subflow->remote_nonce = mp_opt.nonce;
-		pr_debug("subflow=%p, thmac=%llu, remote_nonce=%u backup=%d",
+		pr_debug("subflow=%p, thmac=%llu, remote_nonce=%u backup=%d\n",
 			 subflow, subflow->thmac, subflow->remote_nonce,
 			 subflow->backup);
 
@@ -465,8 +477,11 @@
 		subflow->mp_join = 1;
 		MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_JOINSYNACKRX);
 
+		if (subflow->backup)
+			MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_JOINSYNACKBACKUPRX);
+
 		if (subflow_use_different_dport(mptcp_sk(parent), sk)) {
-			pr_debug("synack inet_dport=%d %d",
+			pr_debug("synack inet_dport=%d %d\n",
 				 ntohs(inet_sk(sk)->inet_dport),
 				 ntohs(inet_sk(parent)->inet_dport));
 			MPTCP_INC_STATS(sock_net(sk), MPTCP_MIB_JOINPORTSYNACKRX);
@@ -483,21 +498,20 @@
 	mptcp_subflow_reset(sk);
 }
 
-struct request_sock_ops mptcp_subflow_request_sock_ops;
-EXPORT_SYMBOL_GPL(mptcp_subflow_request_sock_ops);
-static struct tcp_request_sock_ops subflow_request_sock_ipv4_ops;
+static struct request_sock_ops mptcp_subflow_v4_request_sock_ops __ro_after_init;
+static struct tcp_request_sock_ops subflow_request_sock_ipv4_ops __ro_after_init;
 
 static int subflow_v4_conn_request(struct sock *sk, struct sk_buff *skb)
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(sk);
 
-	pr_debug("subflow=%p", subflow);
+	pr_debug("subflow=%p\n", subflow);
 
 	/* Never answer to SYNs sent to broadcast or multicast */
 	if (skb_rtable(skb)->rt_flags & (RTCF_BROADCAST | RTCF_MULTICAST))
 		goto drop;
 
-	return tcp_conn_request(&mptcp_subflow_request_sock_ops,
+	return tcp_conn_request(&mptcp_subflow_v4_request_sock_ops,
 				&subflow_request_sock_ipv4_ops,
 				sk, skb);
 drop:
@@ -505,17 +519,24 @@
 	return 0;
 }
 
+static void subflow_v4_req_destructor(struct request_sock *req)
+{
+	subflow_req_destructor(req);
+	tcp_request_sock_ops.destructor(req);
+}
+
 #if IS_ENABLED(CONFIG_MPTCP_IPV6)
-static struct tcp_request_sock_ops subflow_request_sock_ipv6_ops;
-static struct inet_connection_sock_af_ops subflow_v6_specific;
-static struct inet_connection_sock_af_ops subflow_v6m_specific;
-static struct proto tcpv6_prot_override;
+static struct request_sock_ops mptcp_subflow_v6_request_sock_ops __ro_after_init;
+static struct tcp_request_sock_ops subflow_request_sock_ipv6_ops __ro_after_init;
+static struct inet_connection_sock_af_ops subflow_v6_specific __ro_after_init;
+static struct inet_connection_sock_af_ops subflow_v6m_specific __ro_after_init;
+static struct proto tcpv6_prot_override __ro_after_init;
 
 static int subflow_v6_conn_request(struct sock *sk, struct sk_buff *skb)
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(sk);
 
-	pr_debug("subflow=%p", subflow);
+	pr_debug("subflow=%p\n", subflow);
 
 	if (skb->protocol == htons(ETH_P_IP))
 		return subflow_v4_conn_request(sk, skb);
@@ -528,15 +549,36 @@
 		return 0;
 	}
 
-	return tcp_conn_request(&mptcp_subflow_request_sock_ops,
+	return tcp_conn_request(&mptcp_subflow_v6_request_sock_ops,
 				&subflow_request_sock_ipv6_ops, sk, skb);
 
 drop:
 	tcp_listendrop(sk);
 	return 0; /* don't send reset */
 }
+
+static void subflow_v6_req_destructor(struct request_sock *req)
+{
+	subflow_req_destructor(req);
+	tcp6_request_sock_ops.destructor(req);
+}
+#endif
+
+struct request_sock *mptcp_subflow_reqsk_alloc(const struct request_sock_ops *ops,
+					       struct sock *sk_listener,
+					       bool attach_listener)
+{
+	if (ops->family == AF_INET)
+		ops = &mptcp_subflow_v4_request_sock_ops;
+#if IS_ENABLED(CONFIG_MPTCP_IPV6)
+	else if (ops->family == AF_INET6)
+		ops = &mptcp_subflow_v6_request_sock_ops;
 #endif
 
+	return inet_reqsk_alloc(ops, sk_listener, attach_listener);
+}
+EXPORT_SYMBOL(mptcp_subflow_reqsk_alloc);
+
 /* validate hmac received in third ACK */
 static bool subflow_hmac_valid(const struct request_sock *req,
 			       const struct mptcp_options_received *mp_opt)
@@ -639,7 +681,7 @@
 	struct sock *new_msk = NULL;
 	struct sock *child;
 
-	pr_debug("listener=%p, req=%p, conn=%p", listener, req, listener->conn);
+	pr_debug("listener=%p, req=%p, conn=%p\n", listener, req, listener->conn);
 
 	/* After child creation we must look for MPC even when options
 	 * are not parsed
@@ -663,7 +705,7 @@
 		 * reordered MPC will cause fallback, but we don't have other
 		 * options.
 		 */
-		mptcp_get_options(sk, skb, &mp_opt);
+		mptcp_get_options(skb, &mp_opt);
 		if (!(mp_opt.suboptions & OPTIONS_MPTCP_MPC)) {
 			fallback = true;
 			goto create_child;
@@ -673,8 +715,8 @@
 		if (!new_msk)
 			fallback = true;
 	} else if (subflow_req->mp_join) {
-		mptcp_get_options(sk, skb, &mp_opt);
-		if (!(mp_opt.suboptions & OPTIONS_MPTCP_MPJ) ||
+		mptcp_get_options(skb, &mp_opt);
+		if (!(mp_opt.suboptions & OPTION_MPTCP_MPJ_ACK) ||
 		    !subflow_hmac_valid(req, &mp_opt) ||
 		    !mptcp_can_accept_new_subflow(subflow_req->msk)) {
 			SUBFLOW_REQ_INC_STATS(req, MPTCP_MIB_JOINACKMAC);
@@ -701,6 +743,9 @@
 				goto dispose_child;
 			}
 
+			if (fallback)
+				SUBFLOW_REQ_INC_STATS(req, MPTCP_MIB_MPCAPABLEPASSIVEFALLBACK);
+
 			subflow_drop_ctx(child);
 			goto out;
 		}
@@ -748,7 +793,7 @@
 			ctx->conn = (struct sock *)owner;
 
 			if (subflow_use_different_sport(owner, sk)) {
-				pr_debug("ack inet_sport=%d %d",
+				pr_debug("ack inet_sport=%d %d\n",
 					 ntohs(inet_sk(sk)->inet_sport),
 					 ntohs(inet_sk((struct sock *)owner)->inet_sport));
 				if (!mptcp_pm_sport_in_anno_list(owner, sk)) {
@@ -790,8 +835,8 @@
 	return child;
 }
 
-static struct inet_connection_sock_af_ops subflow_specific;
-static struct proto tcp_prot_override;
+static struct inet_connection_sock_af_ops subflow_specific __ro_after_init;
+static struct proto tcp_prot_override __ro_after_init;
 
 enum mapping_status {
 	MAPPING_OK,
@@ -803,7 +848,7 @@
 
 static void dbg_bad_map(struct mptcp_subflow_context *subflow, u32 ssn)
 {
-	pr_debug("Bad mapping: ssn=%d map_seq=%d map_data_len=%d",
+	pr_debug("Bad mapping: ssn=%d map_seq=%d map_data_len=%d\n",
 		 ssn, subflow->map_subflow_seq, subflow->map_data_len);
 }
 
@@ -813,7 +858,7 @@
 	unsigned int skb_consumed;
 
 	skb_consumed = tcp_sk(ssk)->copied_seq - TCP_SKB_CB(skb)->seq;
-	if (WARN_ON_ONCE(skb_consumed >= skb->len))
+	if (unlikely(skb_consumed >= skb->len))
 		return true;
 
 	return skb->len - skb_consumed <= subflow->map_data_len -
@@ -845,9 +890,8 @@
 					      bool csum_reqd)
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(ssk);
-	struct csum_pseudo_header header;
 	u32 offset, seq, delta;
-	__wsum csum;
+	__sum16 csum;
 	int len;
 
 	if (!csum_reqd)
@@ -908,19 +952,20 @@
 	 * while the pseudo header requires the original DSS data len,
 	 * including that
 	 */
-	header.data_seq = cpu_to_be64(subflow->map_seq);
-	header.subflow_seq = htonl(subflow->map_subflow_seq);
-	header.data_len = htons(subflow->map_data_len + subflow->map_data_fin);
-	header.csum = 0;
-
-	csum = csum_partial(&header, sizeof(header), subflow->map_data_csum);
-	if (unlikely(csum_fold(csum))) {
+	csum = __mptcp_make_csum(subflow->map_seq,
+				 subflow->map_subflow_seq,
+				 subflow->map_data_len + subflow->map_data_fin,
+				 subflow->map_data_csum);
+	if (unlikely(csum)) {
 		MPTCP_INC_STATS(sock_net(ssk), MPTCP_MIB_DATACSUMERR);
-		subflow->send_mp_fail = 1;
-		MPTCP_INC_STATS(sock_net(ssk), MPTCP_MIB_MPFAILTX);
+		if (subflow->mp_join || subflow->valid_csum_seen) {
+			subflow->send_mp_fail = 1;
+			MPTCP_INC_STATS(sock_net(ssk), MPTCP_MIB_MPFAILTX);
+		}
 		return subflow->mp_join ? MAPPING_INVALID : MAPPING_DUMMY;
 	}
 
+	subflow->valid_csum_seen = 1;
 	return MAPPING_OK;
 }
 
@@ -975,7 +1020,7 @@
 		if (data_len == 1) {
 			bool updated = mptcp_update_rcv_data_fin(msk, mpext->data_seq,
 								 mpext->dsn64);
-			pr_debug("DATA_FIN with no payload seq=%llu", mpext->data_seq);
+			pr_debug("DATA_FIN with no payload seq=%llu\n", mpext->data_seq);
 			if (subflow->map_valid) {
 				/* A DATA_FIN might arrive in a DSS
 				 * option before the previous mapping
@@ -985,8 +1030,8 @@
 				skb_ext_del(skb, SKB_EXT_MPTCP);
 				return MAPPING_OK;
 			} else {
-				if (updated && schedule_work(&msk->work))
-					sock_hold((struct sock *)msk);
+				if (updated)
+					mptcp_schedule_work((struct sock *)msk);
 
 				return MAPPING_DATA_FIN;
 			}
@@ -1000,7 +1045,7 @@
 				data_fin_seq &= GENMASK_ULL(31, 0);
 
 			mptcp_update_rcv_data_fin(msk, data_fin_seq, mpext->dsn64);
-			pr_debug("DATA_FIN with mapping seq=%llu dsn64=%d",
+			pr_debug("DATA_FIN with mapping seq=%llu dsn64=%d\n",
 				 data_fin_seq, mpext->dsn64);
 		}
 
@@ -1047,7 +1092,7 @@
 	if (unlikely(subflow->map_csum_reqd != csum_reqd))
 		return MAPPING_INVALID;
 
-	pr_debug("new map seq=%llu subflow_seq=%u data_len=%u csum=%d:%u",
+	pr_debug("new map seq=%llu subflow_seq=%u data_len=%u csum=%d:%u\n",
 		 subflow->map_seq, subflow->map_subflow_seq,
 		 subflow->map_data_len, subflow->map_csum_reqd,
 		 subflow->map_data_csum);
@@ -1072,14 +1117,22 @@
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(ssk);
 	bool fin = TCP_SKB_CB(skb)->tcp_flags & TCPHDR_FIN;
-	u32 incr;
+	struct tcp_sock *tp = tcp_sk(ssk);
+	u32 offset, incr, avail_len;
+
+	offset = tp->copied_seq - TCP_SKB_CB(skb)->seq;
+	if (WARN_ON_ONCE(offset > skb->len))
+		goto out;
 
-	incr = limit >= skb->len ? skb->len + fin : limit;
+	avail_len = skb->len - offset;
+	incr = limit >= avail_len ? avail_len + fin : limit;
 
-	pr_debug("discarding=%d len=%d seq=%d", incr, skb->len,
-		 subflow->map_subflow_seq);
+	pr_debug("discarding=%d len=%d offset=%d seq=%d\n", incr, skb->len,
+		 offset, subflow->map_subflow_seq);
 	MPTCP_INC_STATS(sock_net(ssk), MPTCP_MIB_DUPDATA);
 	tcp_sk(ssk)->copied_seq += incr;
+
+out:
 	if (!before(tcp_sk(ssk)->copied_seq, TCP_SKB_CB(skb)->end_seq))
 		sk_eat_skb(ssk, skb);
 	if (mptcp_subflow_get_map_offset(subflow) >= subflow->map_data_len)
@@ -1091,15 +1144,26 @@
 {
 	struct sock *sk = (struct sock *)msk;
 
-	if (likely(ssk->sk_state != TCP_CLOSE))
+	if (likely(ssk->sk_state != TCP_CLOSE &&
+		   (ssk->sk_state != TCP_CLOSE_WAIT ||
+		    inet_sk_state_load(sk) != TCP_ESTABLISHED)))
 		return;
 
 	if (skb_queue_empty(&ssk->sk_receive_queue) &&
-	    !test_and_set_bit(MPTCP_WORK_CLOSE_SUBFLOW, &msk->flags)) {
-		sock_hold(sk);
-		if (!schedule_work(&msk->work))
-			sock_put(sk);
-	}
+	    !test_and_set_bit(MPTCP_WORK_CLOSE_SUBFLOW, &msk->flags))
+		mptcp_schedule_work(sk);
+}
+
+static bool subflow_can_fallback(struct mptcp_subflow_context *subflow)
+{
+	struct mptcp_sock *msk = mptcp_sk(subflow->conn);
+
+	if (subflow->mp_join)
+		return false;
+	else if (READ_ONCE(msk->csum_enabled))
+		return !subflow->valid_csum_seen;
+	else
+		return READ_ONCE(msk->allow_infinite_fallback);
 }
 
 static bool subflow_check_data_avail(struct sock *ssk)
@@ -1147,7 +1211,7 @@
 
 		old_ack = READ_ONCE(msk->ack_seq);
 		ack_seq = mptcp_subflow_get_mapped_dsn(subflow);
-		pr_debug("msk ack_seq=%llx subflow ack_seq=%llx", old_ack,
+		pr_debug("msk ack_seq=%llx subflow ack_seq=%llx\n", old_ack,
 			 ack_seq);
 		if (unlikely(before64(ack_seq, old_ack))) {
 			mptcp_subflow_discard_data(ssk, skb, old_ack - ack_seq);
@@ -1166,7 +1230,8 @@
 fallback:
 	/* RFC 8684 section 3.7. */
 	if (subflow->send_mp_fail) {
-		if (mptcp_has_another_subflow(ssk)) {
+		if (mptcp_has_another_subflow(ssk) ||
+		    !READ_ONCE(msk->allow_infinite_fallback)) {
 			while ((skb = skb_peek(&ssk->sk_receive_queue)))
 				sk_eat_skb(ssk, skb);
 		}
@@ -1179,7 +1244,7 @@
 		return true;
 	}
 
-	if (subflow->mp_join || subflow->fully_established) {
+	if (!subflow_can_fallback(subflow)) {
 		/* fatal protocol error, close the socket.
 		 * subflow_error_report() will introduce the appropriate barriers
 		 */
@@ -1212,7 +1277,7 @@
 		subflow->map_valid = 0;
 		WRITE_ONCE(subflow->data_avail, 0);
 
-		pr_debug("Done with mapping: seq=%u data_len=%u",
+		pr_debug("Done with mapping: seq=%u data_len=%u\n",
 			 subflow->map_subflow_seq,
 			 subflow->map_data_len);
 	}
@@ -1238,38 +1303,17 @@
 	*full_space = tcp_full_space(sk);
 }
 
-void __mptcp_error_report(struct sock *sk)
-{
-	struct mptcp_subflow_context *subflow;
-	struct mptcp_sock *msk = mptcp_sk(sk);
-
-	mptcp_for_each_subflow(msk, subflow) {
-		struct sock *ssk = mptcp_subflow_tcp_sock(subflow);
-		int err = sock_error(ssk);
-
-		if (!err)
-			continue;
-
-		/* only propagate errors on fallen-back sockets or
-		 * on MPC connect
-		 */
-		if (sk->sk_state != TCP_SYN_SENT && !__mptcp_check_fallback(msk))
-			continue;
-
-		inet_sk_state_store(sk, inet_sk_state_load(ssk));
-		sk->sk_err = -err;
-
-		/* This barrier is coupled with smp_rmb() in mptcp_poll() */
-		smp_wmb();
-		sk_error_report(sk);
-		break;
-	}
-}
-
 static void subflow_error_report(struct sock *ssk)
 {
 	struct sock *sk = mptcp_subflow_ctx(ssk)->conn;
 
+	/* bail early if this is a no-op, so that we avoid introducing a
+	 * problematic lockdep dependency between TCP accept queue lock
+	 * and msk socket spinlock
+	 */
+	if (!sk->sk_socket)
+		return;
+
 	mptcp_data_lock(sk);
 	if (!sock_owned_by_user(sk))
 		__mptcp_error_report(sk);
@@ -1315,7 +1359,7 @@
 	mptcp_write_space(sk);
 }
 
-static struct inet_connection_sock_af_ops *
+static const struct inet_connection_sock_af_ops *
 subflow_default_af_ops(struct sock *sk)
 {
 #if IS_ENABLED(CONFIG_MPTCP_IPV6)
@@ -1330,11 +1374,11 @@
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(sk);
 	struct inet_connection_sock *icsk = inet_csk(sk);
-	struct inet_connection_sock_af_ops *target;
+	const struct inet_connection_sock_af_ops *target;
 
 	target = mapped ? &subflow_v6m_specific : subflow_default_af_ops(sk);
 
-	pr_debug("subflow=%p family=%d ops=%p target=%p mapped=%d",
+	pr_debug("subflow=%p family=%d ops=%p target=%p mapped=%d\n",
 		 subflow, sk->sk_family, icsk->icsk_af_ops, target, mapped);
 
 	if (likely(icsk->icsk_af_ops == target))
@@ -1431,7 +1475,7 @@
 		goto failed;
 
 	mptcp_crypto_key_sha(subflow->remote_key, &remote_token, NULL);
-	pr_debug("msk=%p remote_token=%u local_id=%d remote_id=%d", msk,
+	pr_debug("msk=%p remote_token=%u local_id=%d remote_id=%d\n", msk,
 		 remote_token, local_id, remote_id);
 	subflow->remote_token = remote_token;
 	subflow->local_id = local_id;
@@ -1449,6 +1493,7 @@
 	/* discard the subflow socket */
 	mptcp_sock_graft(ssk, sk->sk_socket);
 	iput(SOCK_INODE(sf));
+	WRITE_ONCE(msk->allow_infinite_fallback, false);
 	return err;
 
 failed_unlink:
@@ -1524,7 +1569,7 @@
 	if (err)
 		return err;
 
-	lock_sock(sf->sk);
+	lock_sock_nested(sf->sk, SINGLE_DEPTH_NESTING);
 
 	/* the newly created socket has to be in the same cgroup as its parent */
 	mptcp_attach_cgroup(sk, sf->sk);
@@ -1534,9 +1579,7 @@
 	 */
 	sf->sk->sk_net_refcnt = 1;
 	get_net(net);
-#ifdef CONFIG_PROC_FS
-	this_cpu_add(*net->core.sock_inuse, 1);
-#endif
+	sock_inuse_add(net, 1);
 	err = tcp_set_ulp(sf->sk, "mptcp");
 	release_sock(sf->sk);
 
@@ -1556,7 +1599,7 @@
 	SOCK_INODE(sf)->i_gid = SOCK_INODE(sk->sk_socket)->i_gid;
 
 	subflow = mptcp_subflow_ctx(sf->sk);
-	pr_debug("subflow=%p", subflow);
+	pr_debug("subflow=%p\n", subflow);
 
 	*new_sock = sf;
 	sock_hold(sk);
@@ -1580,7 +1623,7 @@
 	INIT_LIST_HEAD(&ctx->node);
 	INIT_LIST_HEAD(&ctx->delegated_node);
 
-	pr_debug("subflow=%p", ctx);
+	pr_debug("subflow=%p\n", ctx);
 
 	ctx->tcp_sock = sk;
 
@@ -1607,14 +1650,16 @@
 {
 	struct mptcp_subflow_context *subflow = mptcp_subflow_ctx(sk);
 	struct sock *parent = subflow->conn;
+	struct mptcp_sock *msk;
 
 	__subflow_state_change(sk);
 
+	msk = mptcp_sk(parent);
 	if (subflow_simultaneous_connect(sk)) {
 		mptcp_propagate_sndbuf(parent, sk);
 		mptcp_do_fallback(sk);
-		mptcp_rcv_space_init(mptcp_sk(parent), sk);
-		pr_fallback(mptcp_sk(parent));
+		mptcp_rcv_space_init(msk, sk);
+		pr_fallback(msk);
 		subflow->conn_finished = 1;
 		mptcp_set_connected(parent);
 	}
@@ -1630,11 +1675,12 @@
 
 	subflow_sched_work_if_closed(mptcp_sk(parent), sk);
 
-	if (__mptcp_check_fallback(mptcp_sk(parent)) &&
-	    !subflow->rx_eof && subflow_is_done(sk)) {
-		subflow->rx_eof = 1;
-		mptcp_subflow_eof(parent);
-	}
+	/* when the fallback subflow closes the rx side, trigger a 'dummy'
+	 * ingress data fin, so that the msk state will follow along
+	 */
+	if (__mptcp_check_fallback(msk) && subflow_is_done(sk) && msk->first == sk &&
+	    mptcp_update_rcv_data_fin(msk, READ_ONCE(msk->ack_seq), true))
+		mptcp_schedule_work(parent);
 }
 
 static int subflow_ulp_init(struct sock *sk)
@@ -1658,7 +1704,7 @@
 		goto out;
 	}
 
-	pr_debug("subflow=%p, family=%d", ctx, sk->sk_family);
+	pr_debug("subflow=%p, family=%d\n", ctx, sk->sk_family);
 
 	tp->is_mptcp = 1;
 	ctx->icsk_af_ops = icsk->icsk_af_ops;
@@ -1742,6 +1788,7 @@
 		new_ctx->mp_join = 1;
 		new_ctx->fully_established = 1;
 		new_ctx->backup = subflow_req->backup;
+		new_ctx->request_bkup = subflow_req->request_bkup;
 		new_ctx->local_id = subflow_req->local_id;
 		new_ctx->remote_id = subflow_req->remote_id;
 		new_ctx->token = subflow_req->token;
@@ -1770,7 +1817,6 @@
 static int subflow_ops_init(struct request_sock_ops *subflow_ops)
 {
 	subflow_ops->obj_size = sizeof(struct mptcp_subflow_request_sock);
-	subflow_ops->slab_name = "request_sock_subflow";
 
 	subflow_ops->slab = kmem_cache_create(subflow_ops->slab_name,
 					      subflow_ops->obj_size, 0,
@@ -1780,16 +1826,17 @@
 	if (!subflow_ops->slab)
 		return -ENOMEM;
 
-	subflow_ops->destructor = subflow_req_destructor;
-
 	return 0;
 }
 
 void __init mptcp_subflow_init(void)
 {
-	mptcp_subflow_request_sock_ops = tcp_request_sock_ops;
-	if (subflow_ops_init(&mptcp_subflow_request_sock_ops) != 0)
-		panic("MPTCP: failed to init subflow request sock ops\n");
+	mptcp_subflow_v4_request_sock_ops = tcp_request_sock_ops;
+	mptcp_subflow_v4_request_sock_ops.slab_name = "request_sock_subflow_v4";
+	mptcp_subflow_v4_request_sock_ops.destructor = subflow_v4_req_destructor;
+
+	if (subflow_ops_init(&mptcp_subflow_v4_request_sock_ops) != 0)
+		panic("MPTCP: failed to init subflow v4 request sock ops\n");
 
 	subflow_request_sock_ipv4_ops = tcp_request_sock_ipv4_ops;
 	subflow_request_sock_ipv4_ops.route_req = subflow_v4_route_req;
@@ -1803,6 +1850,20 @@
 	tcp_prot_override.release_cb = tcp_release_cb_override;
 
 #if IS_ENABLED(CONFIG_MPTCP_IPV6)
+	/* In struct mptcp_subflow_request_sock, we assume the TCP request sock
+	 * structures for v4 and v6 have the same size. It should not changed in
+	 * the future but better to make sure to be warned if it is no longer
+	 * the case.
+	 */
+	BUILD_BUG_ON(sizeof(struct tcp_request_sock) != sizeof(struct tcp6_request_sock));
+
+	mptcp_subflow_v6_request_sock_ops = tcp6_request_sock_ops;
+	mptcp_subflow_v6_request_sock_ops.slab_name = "request_sock_subflow_v6";
+	mptcp_subflow_v6_request_sock_ops.destructor = subflow_v6_req_destructor;
+
+	if (subflow_ops_init(&mptcp_subflow_v6_request_sock_ops) != 0)
+		panic("MPTCP: failed to init subflow v6 request sock ops\n");
+
 	subflow_request_sock_ipv6_ops = tcp_request_sock_ipv6_ops;
 	subflow_request_sock_ipv6_ops.route_req = subflow_v6_route_req;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/internal.h
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/internal.h
@@ -105,8 +105,11 @@
 
 
 struct ncsi_channel_version {
-	u32 version;		/* Supported BCD encoded NCSI version */
-	u32 alpha2;		/* Supported BCD encoded NCSI version */
+	u8   major;		/* NCSI version major */
+	u8   minor;		/* NCSI version minor */
+	u8   update;		/* NCSI version update */
+	char alpha1;		/* NCSI version alpha1 */
+	char alpha2;		/* NCSI version alpha2 */
 	u8  fw_name[12];	/* Firmware name string                */
 	u32 fw_version;		/* Firmware version                   */
 	u16 pci_ids[4];		/* PCI identification                 */
@@ -286,6 +289,7 @@
 	ncsi_dev_state_config_sp	= 0x0301,
 	ncsi_dev_state_config_cis,
 	ncsi_dev_state_config_oem_gma,
+	ncsi_dev_state_config_apply_mac,
 	ncsi_dev_state_config_clear_vids,
 	ncsi_dev_state_config_svf,
 	ncsi_dev_state_config_ev,
@@ -319,9 +323,11 @@
 #define NCSI_DEV_RESHUFFLE	4
 #define NCSI_DEV_RESET		8            /* Reset state of NC          */
 	unsigned int        gma_flag;        /* OEM GMA flag               */
+	struct sockaddr     pending_mac;     /* MAC address received from GMA */
 	spinlock_t          lock;            /* Protect the NCSI device    */
 	unsigned int        package_probe_id;/* Current ID during probe    */
 	unsigned int        package_num;     /* Number of packages         */
+	unsigned int        channel_probe_id;/* Current cahnnel ID during probe */
 	struct list_head    packages;        /* List of packages           */
 	struct ncsi_channel *hot_channel;    /* Channel was ever active    */
 	struct ncsi_request requests[256];   /* Request table              */
@@ -340,6 +346,7 @@
 	bool                multi_package;   /* Enable multiple packages   */
 	bool                mlx_multi_host;  /* Enable multi host Mellanox */
 	u32                 package_whitelist; /* Packages to configure    */
+	unsigned char       channel_count;     /* Num of channels to probe   */
 };
 
 struct ncsi_cmd_arg {
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/ncsi-aen.c
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/ncsi-aen.c
@@ -165,6 +165,7 @@
 	nc->state = NCSI_CHANNEL_INACTIVE;
 	list_add_tail_rcu(&nc->link, &ndp->channel_queue);
 	spin_unlock_irqrestore(&ndp->lock, flags);
+	nc->modes[NCSI_MODE_TX_ENABLE].enable = 0;
 
 	return ncsi_process_next_channel(ndp);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/ncsi-cmd.c
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/ncsi-cmd.c
@@ -18,6 +18,8 @@
 #include "internal.h"
 #include "ncsi-pkt.h"
 
+static const int padding_bytes = 26;
+
 u32 ncsi_calculate_checksum(unsigned char *data, int len)
 {
 	u32 checksum = 0;
@@ -213,12 +215,17 @@
 {
 	struct ncsi_cmd_oem_pkt *cmd;
 	unsigned int len;
+	int payload;
+	/* NC-SI spec DSP_0222_1.2.0, section 8.2.2.2
+	 * requires payload to be padded with 0 to
+	 * 32-bit boundary before the checksum field.
+	 * Ensure the padding bytes are accounted for in
+	 * skb allocation
+	 */
 
+	payload = ALIGN(nca->payload, 4);
 	len = sizeof(struct ncsi_cmd_pkt_hdr) + 4;
-	if (nca->payload < 26)
-		len += 26;
-	else
-		len += nca->payload;
+	len += max(payload, padding_bytes);
 
 	cmd = skb_put_zero(skb, len);
 	memcpy(&cmd->mfr_id, nca->data, nca->payload);
@@ -262,7 +269,8 @@
 	{ NCSI_PKT_CMD_GPS,    0, ncsi_cmd_handler_default },
 	{ NCSI_PKT_CMD_OEM,   -1, ncsi_cmd_handler_oem     },
 	{ NCSI_PKT_CMD_PLDM,   0, NULL                     },
-	{ NCSI_PKT_CMD_GPUUID, 0, ncsi_cmd_handler_default }
+	{ NCSI_PKT_CMD_GPUUID, 0, ncsi_cmd_handler_default },
+	{ NCSI_PKT_CMD_GMCMA,  0, ncsi_cmd_handler_default }
 };
 
 static struct ncsi_request *ncsi_alloc_command(struct ncsi_cmd_arg *nca)
@@ -272,6 +280,7 @@
 	struct net_device *dev = nd->dev;
 	int hlen = LL_RESERVED_SPACE(dev);
 	int tlen = dev->needed_tailroom;
+	int payload;
 	int len = hlen + tlen;
 	struct sk_buff *skb;
 	struct ncsi_request *nr;
@@ -281,14 +290,14 @@
 		return NULL;
 
 	/* NCSI command packet has 16-bytes header, payload, 4 bytes checksum.
+	 * Payload needs padding so that the checksum field following payload is
+	 * aligned to 32-bit boundary.
 	 * The packet needs padding if its payload is less than 26 bytes to
 	 * meet 64 bytes minimal ethernet frame length.
 	 */
 	len += sizeof(struct ncsi_cmd_pkt_hdr) + 4;
-	if (nca->payload < 26)
-		len += 26;
-	else
-		len += nca->payload;
+	payload = ALIGN(nca->payload, 4);
+	len += max(payload, padding_bytes);
 
 	/* Allocate skb */
 	skb = alloc_skb(len, GFP_ATOMIC);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/ncsi-manage.c
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/ncsi-manage.c
@@ -510,17 +510,19 @@
 
 		break;
 	case ncsi_dev_state_suspend_gls:
-		ndp->pending_req_num = np->channel_num;
+		ndp->pending_req_num = 1;
 
 		nca.type = NCSI_PKT_CMD_GLS;
 		nca.package = np->id;
+		nca.channel = ndp->channel_probe_id;
+		ret = ncsi_xmit_cmd(&nca);
+		if (ret)
+			goto error;
+		ndp->channel_probe_id++;
 
-		nd->state = ncsi_dev_state_suspend_dcnt;
-		NCSI_FOR_EACH_CHANNEL(np, nc) {
-			nca.channel = nc->id;
-			ret = ncsi_xmit_cmd(&nca);
-			if (ret)
-				goto error;
+		if (ndp->channel_probe_id == ndp->channel_count) {
+			ndp->channel_probe_id = 0;
+			nd->state = ncsi_dev_state_suspend_dcnt;
 		}
 
 		break;
@@ -689,8 +691,6 @@
 	return 0;
 }
 
-#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY)
-
 static int ncsi_oem_keep_phy_intel(struct ncsi_cmd_arg *nca)
 {
 	unsigned char data[NCSI_OEM_INTEL_CMD_KEEP_PHY_LEN];
@@ -716,10 +716,6 @@
 	return ret;
 }
 
-#endif
-
-#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_GET_MAC)
-
 /* NCSI OEM Command APIs */
 static int ncsi_oem_gma_handler_bcm(struct ncsi_cmd_arg *nca)
 {
@@ -856,8 +852,6 @@
 	return nch->handler(nca);
 }
 
-#endif /* CONFIG_NCSI_OEM_CMD_GET_MAC */
-
 /* Determine if a given channel from the channel_queue should be used for Tx */
 static bool ncsi_channel_is_tx(struct ncsi_dev_priv *ndp,
 			       struct ncsi_channel *nc)
@@ -1039,24 +1033,39 @@
 			goto error;
 		}
 
-		nd->state = ncsi_dev_state_config_oem_gma;
+		nd->state = IS_ENABLED(CONFIG_NCSI_OEM_CMD_GET_MAC)
+			  ? ncsi_dev_state_config_oem_gma
+			  : ncsi_dev_state_config_clear_vids;
 		break;
 	case ncsi_dev_state_config_oem_gma:
-		nd->state = ncsi_dev_state_config_clear_vids;
-		ret = -1;
+		nd->state = ncsi_dev_state_config_apply_mac;
 
-#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_GET_MAC)
-		nca.type = NCSI_PKT_CMD_OEM;
 		nca.package = np->id;
 		nca.channel = nc->id;
 		ndp->pending_req_num = 1;
-		ret = ncsi_gma_handler(&nca, nc->version.mf_id);
-#endif /* CONFIG_NCSI_OEM_CMD_GET_MAC */
-
-		if (ret < 0)
+		if (nc->version.major >= 1 && nc->version.minor >= 2) {
+			nca.type = NCSI_PKT_CMD_GMCMA;
+			ret = ncsi_xmit_cmd(&nca);
+		} else {
+			nca.type = NCSI_PKT_CMD_OEM;
+			ret = ncsi_gma_handler(&nca, nc->version.mf_id);
+		}
+		if (ret < 0) {
+			nd->state = ncsi_dev_state_config_clear_vids;
 			schedule_work(&ndp->work);
+		}
 
 		break;
+	case ncsi_dev_state_config_apply_mac:
+		rtnl_lock();
+		ret = dev_set_mac_address(dev, &ndp->pending_mac, NULL);
+		rtnl_unlock();
+		if (ret < 0)
+			netdev_warn(dev, "NCSI: 'Writing MAC address to device failed\n");
+
+		nd->state = ncsi_dev_state_config_clear_vids;
+
+		fallthrough;
 	case ncsi_dev_state_config_clear_vids:
 	case ncsi_dev_state_config_svf:
 	case ncsi_dev_state_config_ev:
@@ -1350,7 +1359,6 @@
 {
 	struct ncsi_dev *nd = &ndp->ndev;
 	struct ncsi_package *np;
-	struct ncsi_channel *nc;
 	struct ncsi_cmd_arg nca;
 	unsigned char index;
 	int ret;
@@ -1377,6 +1385,12 @@
 		nd->state = ncsi_dev_state_probe_package;
 		break;
 	case ncsi_dev_state_probe_package:
+		if (ndp->package_probe_id >= 8) {
+			/* Last package probed, finishing */
+			ndp->flags |= NCSI_DEV_PROBED;
+			break;
+		}
+
 		ndp->pending_req_num = 1;
 
 		nca.type = NCSI_PKT_CMD_SP;
@@ -1404,7 +1418,6 @@
 
 		schedule_work(&ndp->work);
 		break;
-#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_GET_MAC)
 	case ncsi_dev_state_probe_mlx_gma:
 		ndp->pending_req_num = 1;
 
@@ -1429,25 +1442,6 @@
 
 		nd->state = ncsi_dev_state_probe_cis;
 		break;
-#endif /* CONFIG_NCSI_OEM_CMD_GET_MAC */
-	case ncsi_dev_state_probe_cis:
-		ndp->pending_req_num = NCSI_RESERVED_CHANNEL;
-
-		/* Clear initial state */
-		nca.type = NCSI_PKT_CMD_CIS;
-		nca.package = ndp->active_package->id;
-		for (index = 0; index < NCSI_RESERVED_CHANNEL; index++) {
-			nca.channel = index;
-			ret = ncsi_xmit_cmd(&nca);
-			if (ret)
-				goto error;
-		}
-
-		nd->state = ncsi_dev_state_probe_gvi;
-		if (IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY))
-			nd->state = ncsi_dev_state_probe_keep_phy;
-		break;
-#if IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY)
 	case ncsi_dev_state_probe_keep_phy:
 		ndp->pending_req_num = 1;
 
@@ -1460,15 +1454,17 @@
 
 		nd->state = ncsi_dev_state_probe_gvi;
 		break;
-#endif /* CONFIG_NCSI_OEM_CMD_KEEP_PHY */
+	case ncsi_dev_state_probe_cis:
 	case ncsi_dev_state_probe_gvi:
 	case ncsi_dev_state_probe_gc:
 	case ncsi_dev_state_probe_gls:
 		np = ndp->active_package;
-		ndp->pending_req_num = np->channel_num;
+		ndp->pending_req_num = 1;
 
-		/* Retrieve version, capability or link status */
-		if (nd->state == ncsi_dev_state_probe_gvi)
+		/* Clear initial state Retrieve version, capability or link status */
+		if (nd->state == ncsi_dev_state_probe_cis)
+			nca.type = NCSI_PKT_CMD_CIS;
+		else if (nd->state == ncsi_dev_state_probe_gvi)
 			nca.type = NCSI_PKT_CMD_GVI;
 		else if (nd->state == ncsi_dev_state_probe_gc)
 			nca.type = NCSI_PKT_CMD_GC;
@@ -1476,19 +1472,29 @@
 			nca.type = NCSI_PKT_CMD_GLS;
 
 		nca.package = np->id;
-		NCSI_FOR_EACH_CHANNEL(np, nc) {
-			nca.channel = nc->id;
-			ret = ncsi_xmit_cmd(&nca);
-			if (ret)
-				goto error;
-		}
+		nca.channel = ndp->channel_probe_id;
+
+		ret = ncsi_xmit_cmd(&nca);
+		if (ret)
+			goto error;
 
-		if (nd->state == ncsi_dev_state_probe_gvi)
+		if (nd->state == ncsi_dev_state_probe_cis) {
+			nd->state = ncsi_dev_state_probe_gvi;
+			if (IS_ENABLED(CONFIG_NCSI_OEM_CMD_KEEP_PHY) && ndp->channel_probe_id == 0)
+				nd->state = ncsi_dev_state_probe_keep_phy;
+		} else if (nd->state == ncsi_dev_state_probe_gvi) {
 			nd->state = ncsi_dev_state_probe_gc;
-		else if (nd->state == ncsi_dev_state_probe_gc)
+		} else if (nd->state == ncsi_dev_state_probe_gc) {
 			nd->state = ncsi_dev_state_probe_gls;
-		else
+		} else {
+			nd->state = ncsi_dev_state_probe_cis;
+			ndp->channel_probe_id++;
+		}
+
+		if (ndp->channel_probe_id == ndp->channel_count) {
+			ndp->channel_probe_id = 0;
 			nd->state = ncsi_dev_state_probe_dp;
+		}
 		break;
 	case ncsi_dev_state_probe_dp:
 		ndp->pending_req_num = 1;
@@ -1501,13 +1507,8 @@
 		if (ret)
 			goto error;
 
-		/* Probe next package */
+		/* Probe next package after receiving response */
 		ndp->package_probe_id++;
-		if (ndp->package_probe_id >= 8) {
-			/* Probe finished */
-			ndp->flags |= NCSI_DEV_PROBED;
-			break;
-		}
 		nd->state = ncsi_dev_state_probe_package;
 		ndp->active_package = NULL;
 		break;
@@ -1789,6 +1790,7 @@
 		ndp->requests[i].ndp = ndp;
 		timer_setup(&ndp->requests[i].timer, ncsi_request_timeout, 0);
 	}
+	ndp->channel_count = NCSI_RESERVED_CHANNEL;
 
 	spin_lock_irqsave(&ncsi_dev_lock, flags);
 	list_add_tail_rcu(&ndp->node, &ncsi_dev_list);
@@ -1821,6 +1823,7 @@
 
 	if (!(ndp->flags & NCSI_DEV_PROBED)) {
 		ndp->package_probe_id = 0;
+		ndp->channel_probe_id = 0;
 		nd->state = ncsi_dev_state_probe;
 		schedule_work(&ndp->work);
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/ncsi-netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/ncsi-netlink.c
@@ -71,8 +71,8 @@
 	if (nc == nc->package->preferred_channel)
 		nla_put_flag(skb, NCSI_CHANNEL_ATTR_FORCED);
 
-	nla_put_u32(skb, NCSI_CHANNEL_ATTR_VERSION_MAJOR, nc->version.version);
-	nla_put_u32(skb, NCSI_CHANNEL_ATTR_VERSION_MINOR, nc->version.alpha2);
+	nla_put_u32(skb, NCSI_CHANNEL_ATTR_VERSION_MAJOR, nc->version.major);
+	nla_put_u32(skb, NCSI_CHANNEL_ATTR_VERSION_MINOR, nc->version.minor);
 	nla_put_string(skb, NCSI_CHANNEL_ATTR_VERSION_STR, nc->version.fw_name);
 
 	vid_nest = nla_nest_start_noflag(skb, NCSI_CHANNEL_ATTR_VLAN_LIST);
@@ -112,7 +112,11 @@
 		pnest = nla_nest_start_noflag(skb, NCSI_PKG_ATTR);
 		if (!pnest)
 			return -ENOMEM;
-		nla_put_u32(skb, NCSI_PKG_ATTR_ID, np->id);
+		rc = nla_put_u32(skb, NCSI_PKG_ATTR_ID, np->id);
+		if (rc) {
+			nla_nest_cancel(skb, pnest);
+			return rc;
+		}
 		if ((0x1 << np->id) == ndp->package_whitelist)
 			nla_put_flag(skb, NCSI_PKG_ATTR_FORCED);
 		cnest = nla_nest_start_noflag(skb, NCSI_PKG_ATTR_CHANNEL_LIST);
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/ncsi-pkt.h
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/ncsi-pkt.h
@@ -197,9 +197,12 @@
 /* Get Version ID */
 struct ncsi_rsp_gvi_pkt {
 	struct ncsi_rsp_pkt_hdr rsp;          /* Response header */
-	__be32                  ncsi_version; /* NCSI version    */
+	unsigned char           major;        /* NCSI version major */
+	unsigned char           minor;        /* NCSI version minor */
+	unsigned char           update;       /* NCSI version update */
+	unsigned char           alpha1;       /* NCSI version alpha1 */
 	unsigned char           reserved[3];  /* Reserved        */
-	unsigned char           alpha2;       /* NCSI version    */
+	unsigned char           alpha2;       /* NCSI version alpha2 */
 	unsigned char           fw_name[12];  /* f/w name string */
 	__be32                  fw_version;   /* f/w version     */
 	__be16                  pci_ids[4];   /* PCI IDs         */
@@ -335,6 +338,14 @@
 	__be32                  checksum;
 };
 
+/* Get MC MAC Address */
+struct ncsi_rsp_gmcma_pkt {
+	struct ncsi_rsp_pkt_hdr rsp;
+	unsigned char           address_count;
+	unsigned char           reserved[3];
+	unsigned char           addresses[][ETH_ALEN];
+};
+
 /* AEN: Link State Change */
 struct ncsi_aen_lsc_pkt {
 	struct ncsi_aen_pkt_hdr aen;        /* AEN header      */
@@ -395,6 +406,7 @@
 #define NCSI_PKT_CMD_GPUUID	0x52 /* Get package UUID                 */
 #define NCSI_PKT_CMD_QPNPR	0x56 /* Query Pending NC PLDM request */
 #define NCSI_PKT_CMD_SNPR	0x57 /* Send NC PLDM Reply  */
+#define NCSI_PKT_CMD_GMCMA	0x58 /* Get MC MAC Address */
 
 
 /* NCSI packet responses */
@@ -430,6 +442,7 @@
 #define NCSI_PKT_RSP_GPUUID	(NCSI_PKT_CMD_GPUUID + 0x80)
 #define NCSI_PKT_RSP_QPNPR	(NCSI_PKT_CMD_QPNPR   + 0x80)
 #define NCSI_PKT_RSP_SNPR	(NCSI_PKT_CMD_SNPR   + 0x80)
+#define NCSI_PKT_RSP_GMCMA	(NCSI_PKT_CMD_GMCMA  + 0x80)
 
 /* NCSI response code/reason */
 #define NCSI_PKT_RSP_C_COMPLETED	0x0000 /* Command Completed        */
--- linux-xilinx-zynqmp-5.15.0.orig/net/ncsi/ncsi-rsp.c
+++ linux-xilinx-zynqmp-5.15.0/net/ncsi/ncsi-rsp.c
@@ -19,6 +19,19 @@
 #include "ncsi-pkt.h"
 #include "ncsi-netlink.h"
 
+/* Nibbles within [0xA, 0xF] add zero "0" to the returned value.
+ * Optional fields (encoded as 0xFF) will default to zero.
+ */
+static u8 decode_bcd_u8(u8 x)
+{
+	int lo = x & 0xF;
+	int hi = x >> 4;
+
+	lo = lo < 0xA ? lo : 0;
+	hi = hi < 0xA ? hi : 0;
+	return lo + hi * 10;
+}
+
 static int ncsi_validate_rsp_pkt(struct ncsi_request *nr,
 				 unsigned short payload)
 {
@@ -611,30 +624,37 @@
 	return 0;
 }
 
-/* Response handler for Mellanox command Get Mac Address */
-static int ncsi_rsp_handler_oem_mlx_gma(struct ncsi_request *nr)
+/* Response handler for Get Mac Address command */
+static int ncsi_rsp_handler_oem_gma(struct ncsi_request *nr, int mfr_id)
 {
 	struct ncsi_dev_priv *ndp = nr->ndp;
+	struct sockaddr *saddr = &ndp->pending_mac;
 	struct net_device *ndev = ndp->ndev.dev;
-	const struct net_device_ops *ops = ndev->netdev_ops;
 	struct ncsi_rsp_oem_pkt *rsp;
-	struct sockaddr saddr;
-	int ret = 0;
+	u32 mac_addr_off = 0;
 
 	/* Get the response header */
 	rsp = (struct ncsi_rsp_oem_pkt *)skb_network_header(nr->rsp);
 
-	saddr.sa_family = ndev->type;
 	ndev->priv_flags |= IFF_LIVE_ADDR_CHANGE;
-	memcpy(saddr.sa_data, &rsp->data[MLX_MAC_ADDR_OFFSET], ETH_ALEN);
+	if (mfr_id == NCSI_OEM_MFR_BCM_ID)
+		mac_addr_off = BCM_MAC_ADDR_OFFSET;
+	else if (mfr_id == NCSI_OEM_MFR_MLX_ID)
+		mac_addr_off = MLX_MAC_ADDR_OFFSET;
+	else if (mfr_id == NCSI_OEM_MFR_INTEL_ID)
+		mac_addr_off = INTEL_MAC_ADDR_OFFSET;
+
+	saddr->sa_family = ndev->type;
+	memcpy(saddr->sa_data, &rsp->data[mac_addr_off], ETH_ALEN);
+	if (mfr_id == NCSI_OEM_MFR_BCM_ID || mfr_id == NCSI_OEM_MFR_INTEL_ID)
+		eth_addr_inc((u8 *)saddr->sa_data);
+	if (!is_valid_ether_addr((const u8 *)saddr->sa_data))
+		return -ENXIO;
+
 	/* Set the flag for GMA command which should only be called once */
 	ndp->gma_flag = 1;
 
-	ret = ops->ndo_set_mac_address(ndev, &saddr);
-	if (ret < 0)
-		netdev_warn(ndev, "NCSI: 'Writing mac address to device failed\n");
-
-	return ret;
+	return 0;
 }
 
 /* Response handler for Mellanox card */
@@ -649,41 +669,10 @@
 
 	if (mlx->cmd == NCSI_OEM_MLX_CMD_GMA &&
 	    mlx->param == NCSI_OEM_MLX_CMD_GMA_PARAM)
-		return ncsi_rsp_handler_oem_mlx_gma(nr);
+		return ncsi_rsp_handler_oem_gma(nr, NCSI_OEM_MFR_MLX_ID);
 	return 0;
 }
 
-/* Response handler for Broadcom command Get Mac Address */
-static int ncsi_rsp_handler_oem_bcm_gma(struct ncsi_request *nr)
-{
-	struct ncsi_dev_priv *ndp = nr->ndp;
-	struct net_device *ndev = ndp->ndev.dev;
-	const struct net_device_ops *ops = ndev->netdev_ops;
-	struct ncsi_rsp_oem_pkt *rsp;
-	struct sockaddr saddr;
-	int ret = 0;
-
-	/* Get the response header */
-	rsp = (struct ncsi_rsp_oem_pkt *)skb_network_header(nr->rsp);
-
-	saddr.sa_family = ndev->type;
-	ndev->priv_flags |= IFF_LIVE_ADDR_CHANGE;
-	memcpy(saddr.sa_data, &rsp->data[BCM_MAC_ADDR_OFFSET], ETH_ALEN);
-	/* Increase mac address by 1 for BMC's address */
-	eth_addr_inc((u8 *)saddr.sa_data);
-	if (!is_valid_ether_addr((const u8 *)saddr.sa_data))
-		return -ENXIO;
-
-	/* Set the flag for GMA command which should only be called once */
-	ndp->gma_flag = 1;
-
-	ret = ops->ndo_set_mac_address(ndev, &saddr);
-	if (ret < 0)
-		netdev_warn(ndev, "NCSI: 'Writing mac address to device failed\n");
-
-	return ret;
-}
-
 /* Response handler for Broadcom card */
 static int ncsi_rsp_handler_oem_bcm(struct ncsi_request *nr)
 {
@@ -695,42 +684,10 @@
 	bcm = (struct ncsi_rsp_oem_bcm_pkt *)(rsp->data);
 
 	if (bcm->type == NCSI_OEM_BCM_CMD_GMA)
-		return ncsi_rsp_handler_oem_bcm_gma(nr);
+		return ncsi_rsp_handler_oem_gma(nr, NCSI_OEM_MFR_BCM_ID);
 	return 0;
 }
 
-/* Response handler for Intel command Get Mac Address */
-static int ncsi_rsp_handler_oem_intel_gma(struct ncsi_request *nr)
-{
-	struct ncsi_dev_priv *ndp = nr->ndp;
-	struct net_device *ndev = ndp->ndev.dev;
-	const struct net_device_ops *ops = ndev->netdev_ops;
-	struct ncsi_rsp_oem_pkt *rsp;
-	struct sockaddr saddr;
-	int ret = 0;
-
-	/* Get the response header */
-	rsp = (struct ncsi_rsp_oem_pkt *)skb_network_header(nr->rsp);
-
-	saddr.sa_family = ndev->type;
-	ndev->priv_flags |= IFF_LIVE_ADDR_CHANGE;
-	memcpy(saddr.sa_data, &rsp->data[INTEL_MAC_ADDR_OFFSET], ETH_ALEN);
-	/* Increase mac address by 1 for BMC's address */
-	eth_addr_inc((u8 *)saddr.sa_data);
-	if (!is_valid_ether_addr((const u8 *)saddr.sa_data))
-		return -ENXIO;
-
-	/* Set the flag for GMA command which should only be called once */
-	ndp->gma_flag = 1;
-
-	ret = ops->ndo_set_mac_address(ndev, &saddr);
-	if (ret < 0)
-		netdev_warn(ndev,
-			    "NCSI: 'Writing mac address to device failed\n");
-
-	return ret;
-}
-
 /* Response handler for Intel card */
 static int ncsi_rsp_handler_oem_intel(struct ncsi_request *nr)
 {
@@ -742,7 +699,7 @@
 	intel = (struct ncsi_rsp_oem_intel_pkt *)(rsp->data);
 
 	if (intel->cmd == NCSI_OEM_INTEL_CMD_GMA)
-		return ncsi_rsp_handler_oem_intel_gma(nr);
+		return ncsi_rsp_handler_oem_gma(nr, NCSI_OEM_MFR_INTEL_ID);
 
 	return 0;
 }
@@ -804,9 +761,18 @@
 	if (!nc)
 		return -ENODEV;
 
-	/* Update to channel's version info */
+	/* Update channel's version info
+	 *
+	 * Major, minor, and update fields are supposed to be
+	 * unsigned integers encoded as packed BCD.
+	 *
+	 * Alpha1 and alpha2 are ISO/IEC 8859-1 characters.
+	 */
 	ncv = &nc->version;
-	ncv->version = ntohl(rsp->ncsi_version);
+	ncv->major = decode_bcd_u8(rsp->major);
+	ncv->minor = decode_bcd_u8(rsp->minor);
+	ncv->update = decode_bcd_u8(rsp->update);
+	ncv->alpha1 = rsp->alpha1;
 	ncv->alpha2 = rsp->alpha2;
 	memcpy(ncv->fw_name, rsp->fw_name, 12);
 	ncv->fw_version = ntohl(rsp->fw_version);
@@ -822,12 +788,13 @@
 	struct ncsi_rsp_gc_pkt *rsp;
 	struct ncsi_dev_priv *ndp = nr->ndp;
 	struct ncsi_channel *nc;
+	struct ncsi_package *np;
 	size_t size;
 
 	/* Find the channel */
 	rsp = (struct ncsi_rsp_gc_pkt *)skb_network_header(nr->rsp);
 	ncsi_find_package_and_channel(ndp, rsp->rsp.common.channel,
-				      NULL, &nc);
+				      &np, &nc);
 	if (!nc)
 		return -ENODEV;
 
@@ -862,6 +829,7 @@
 	 */
 	nc->vlan_filter.bitmap = U64_MAX;
 	nc->vlan_filter.n_vids = rsp->vlan_cnt;
+	np->ndp->channel_count = rsp->channel_cnt;
 
 	return 0;
 }
@@ -1118,6 +1086,42 @@
 	return ret;
 }
 
+static int ncsi_rsp_handler_gmcma(struct ncsi_request *nr)
+{
+	struct ncsi_dev_priv *ndp = nr->ndp;
+	struct sockaddr *saddr = &ndp->pending_mac;
+	struct net_device *ndev = ndp->ndev.dev;
+	struct ncsi_rsp_gmcma_pkt *rsp;
+	int i;
+
+	rsp = (struct ncsi_rsp_gmcma_pkt *)skb_network_header(nr->rsp);
+	ndev->priv_flags |= IFF_LIVE_ADDR_CHANGE;
+
+	netdev_info(ndev, "NCSI: Received %d provisioned MAC addresses\n",
+		    rsp->address_count);
+	for (i = 0; i < rsp->address_count; i++) {
+		netdev_info(ndev, "NCSI: MAC address %d: %02x:%02x:%02x:%02x:%02x:%02x\n",
+			    i, rsp->addresses[i][0], rsp->addresses[i][1],
+			    rsp->addresses[i][2], rsp->addresses[i][3],
+			    rsp->addresses[i][4], rsp->addresses[i][5]);
+	}
+
+	saddr->sa_family = ndev->type;
+	for (i = 0; i < rsp->address_count; i++) {
+		if (!is_valid_ether_addr(rsp->addresses[i])) {
+			netdev_warn(ndev, "NCSI: Unable to assign %pM to device\n",
+				    rsp->addresses[i]);
+			continue;
+		}
+		memcpy(saddr->sa_data, rsp->addresses[i], ETH_ALEN);
+		netdev_warn(ndev, "NCSI: Will set MAC address to %pM\n", saddr->sa_data);
+		break;
+	}
+
+	ndp->gma_flag = 1;
+	return 0;
+}
+
 static struct ncsi_rsp_handler {
 	unsigned char	type;
 	int             payload;
@@ -1154,7 +1158,8 @@
 	{ NCSI_PKT_RSP_PLDM,   -1, ncsi_rsp_handler_pldm    },
 	{ NCSI_PKT_RSP_GPUUID, 20, ncsi_rsp_handler_gpuuid  },
 	{ NCSI_PKT_RSP_QPNPR,  -1, ncsi_rsp_handler_pldm    },
-	{ NCSI_PKT_RSP_SNPR,   -1, ncsi_rsp_handler_pldm    }
+	{ NCSI_PKT_RSP_SNPR,   -1, ncsi_rsp_handler_pldm    },
+	{ NCSI_PKT_RSP_GMCMA,  -1, ncsi_rsp_handler_gmcma   },
 };
 
 int ncsi_rcv_rsp(struct sk_buff *skb, struct net_device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/Kconfig
@@ -133,7 +133,6 @@
 
 config NF_CONNTRACK_PROCFS
 	bool "Supply CT list in procfs (OBSOLETE)"
-	default y
 	depends on PROC_FS
 	help
 	This option enables for the list of known conntrack entries
@@ -729,6 +728,15 @@
 
 	  To compile it as a module, choose M here.
 
+config NF_FLOW_TABLE_PROCFS
+	bool "Supply flow table statistics in procfs"
+	default y
+	depends on PROC_FS
+	depends on SYSCTL
+	help
+	  This option enables for the flow table offload statistics
+	  to be shown in procfs under net/netfilter/nf_flowtable.
+
 config NETFILTER_XTABLES
 	tristate "Netfilter Xtables support (required for ip_tables)"
 	default m if NETFILTER_ADVANCED=n
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/Makefile
@@ -124,6 +124,7 @@
 obj-$(CONFIG_NF_FLOW_TABLE)	+= nf_flow_table.o
 nf_flow_table-objs		:= nf_flow_table_core.o nf_flow_table_ip.o \
 				   nf_flow_table_offload.o
+nf_flow_table-$(CONFIG_NF_FLOW_TABLE_PROCFS) += nf_flow_table_procfs.o
 
 obj-$(CONFIG_NF_FLOW_TABLE_INET) += nf_flow_table_inet.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/core.c
@@ -300,12 +300,6 @@
 		if (WARN_ON_ONCE(ARRAY_SIZE(net->nf.hooks_ipv6) <= hooknum))
 			return NULL;
 		return net->nf.hooks_ipv6 + hooknum;
-#if IS_ENABLED(CONFIG_DECNET)
-	case NFPROTO_DECNET:
-		if (WARN_ON_ONCE(ARRAY_SIZE(net->nf.hooks_decnet) <= hooknum))
-			return NULL;
-		return net->nf.hooks_decnet + hooknum;
-#endif
 	default:
 		WARN_ON_ONCE(1);
 		return NULL;
@@ -406,14 +400,15 @@
 	p = nf_entry_dereference(*pp);
 	new_hooks = nf_hook_entries_grow(p, reg);
 
-	if (!IS_ERR(new_hooks))
+	if (!IS_ERR(new_hooks)) {
+		hooks_validate(new_hooks);
 		rcu_assign_pointer(*pp, new_hooks);
+	}
 
 	mutex_unlock(&nf_hook_mutex);
 	if (IS_ERR(new_hooks))
 		return PTR_ERR(new_hooks);
 
-	hooks_validate(new_hooks);
 #ifdef CONFIG_NETFILTER_INGRESS
 	if (nf_ingress_hook(reg, pf))
 		net_inc_ingress_queue();
@@ -591,7 +586,8 @@
 		case NF_ACCEPT:
 			break;
 		case NF_DROP:
-			kfree_skb(skb);
+			kfree_skb_reason(skb,
+					 SKB_DROP_REASON_NETFILTER_DROP);
 			ret = NF_DROP_GETERR(verdict);
 			if (ret == 0)
 				ret = -EPERM;
@@ -636,32 +632,29 @@
 /* This needs to be compiled in any case to avoid dependencies between the
  * nfnetlink_queue code and nf_conntrack.
  */
-struct nfnl_ct_hook __rcu *nfnl_ct_hook __read_mostly;
+const struct nfnl_ct_hook __rcu *nfnl_ct_hook __read_mostly;
 EXPORT_SYMBOL_GPL(nfnl_ct_hook);
 
-struct nf_ct_hook __rcu *nf_ct_hook __read_mostly;
+const struct nf_ct_hook __rcu *nf_ct_hook __read_mostly;
 EXPORT_SYMBOL_GPL(nf_ct_hook);
 
 #if IS_ENABLED(CONFIG_NF_CONNTRACK)
-/* This does not belong here, but locally generated errors need it if connection
-   tracking in use: without this, connection may not be in hash table, and hence
-   manufactured ICMP or RST packets will not be associated with it. */
-void (*ip_ct_attach)(struct sk_buff *, const struct sk_buff *)
-		__rcu __read_mostly;
-EXPORT_SYMBOL(ip_ct_attach);
-
-struct nf_nat_hook __rcu *nf_nat_hook __read_mostly;
+const struct nf_nat_hook __rcu *nf_nat_hook __read_mostly;
 EXPORT_SYMBOL_GPL(nf_nat_hook);
 
+/* This does not belong here, but locally generated errors need it if connection
+ * tracking in use: without this, connection may not be in hash table, and hence
+ * manufactured ICMP or RST packets will not be associated with it.
+ */
 void nf_ct_attach(struct sk_buff *new, const struct sk_buff *skb)
 {
-	void (*attach)(struct sk_buff *, const struct sk_buff *);
+	const struct nf_ct_hook *ct_hook;
 
 	if (skb->_nfct) {
 		rcu_read_lock();
-		attach = rcu_dereference(ip_ct_attach);
-		if (attach)
-			attach(new, skb);
+		ct_hook = rcu_dereference(nf_ct_hook);
+		if (ct_hook)
+			ct_hook->attach(new, skb);
 		rcu_read_unlock();
 	}
 }
@@ -669,20 +662,38 @@
 
 void nf_conntrack_destroy(struct nf_conntrack *nfct)
 {
-	struct nf_ct_hook *ct_hook;
+	const struct nf_ct_hook *ct_hook;
 
 	rcu_read_lock();
 	ct_hook = rcu_dereference(nf_ct_hook);
-	BUG_ON(ct_hook == NULL);
-	ct_hook->destroy(nfct);
+	if (ct_hook)
+		ct_hook->destroy(nfct);
 	rcu_read_unlock();
+
+	WARN_ON(!ct_hook);
 }
 EXPORT_SYMBOL(nf_conntrack_destroy);
 
+void nf_ct_set_closing(struct nf_conntrack *nfct)
+{
+	const struct nf_ct_hook *ct_hook;
+
+	if (!nfct)
+		return;
+
+	rcu_read_lock();
+	ct_hook = rcu_dereference(nf_ct_hook);
+	if (ct_hook)
+		ct_hook->set_closing(nfct);
+
+	rcu_read_unlock();
+}
+EXPORT_SYMBOL_GPL(nf_ct_set_closing);
+
 bool nf_ct_get_tuple_skb(struct nf_conntrack_tuple *dst_tuple,
 			 const struct sk_buff *skb)
 {
-	struct nf_ct_hook *ct_hook;
+	const struct nf_ct_hook *ct_hook;
 	bool ret = false;
 
 	rcu_read_lock();
@@ -721,10 +732,6 @@
 #ifdef CONFIG_NETFILTER_FAMILY_BRIDGE
 	__netfilter_net_init(net->nf.hooks_bridge, ARRAY_SIZE(net->nf.hooks_bridge));
 #endif
-#if IS_ENABLED(CONFIG_DECNET)
-	__netfilter_net_init(net->nf.hooks_decnet, ARRAY_SIZE(net->nf.hooks_decnet));
-#endif
-
 #ifdef CONFIG_PROC_FS
 	net->nf.proc_netfilter = proc_net_mkdir(net, "netfilter",
 						net->proc_net);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_bitmap_gen.h
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_bitmap_gen.h
@@ -28,6 +28,7 @@
 #define mtype_del		IPSET_TOKEN(MTYPE, _del)
 #define mtype_list		IPSET_TOKEN(MTYPE, _list)
 #define mtype_gc		IPSET_TOKEN(MTYPE, _gc)
+#define mtype_cancel_gc		IPSET_TOKEN(MTYPE, _cancel_gc)
 #define mtype			MTYPE
 
 #define get_ext(set, map, id)	((map)->extensions + ((set)->dsize * (id)))
@@ -57,9 +58,6 @@
 {
 	struct mtype *map = set->data;
 
-	if (SET_WITH_TIMEOUT(set))
-		del_timer_sync(&map->gc);
-
 	if (set->dsize && set->extensions & IPSET_EXT_DESTROY)
 		mtype_ext_cleanup(set);
 	ip_set_free(map->members);
@@ -288,6 +286,15 @@
 	add_timer(&map->gc);
 }
 
+static void
+mtype_cancel_gc(struct ip_set *set)
+{
+	struct mtype *map = set->data;
+
+	if (SET_WITH_TIMEOUT(set))
+		del_timer_sync(&map->gc);
+}
+
 static const struct ip_set_type_variant mtype = {
 	.kadt	= mtype_kadt,
 	.uadt	= mtype_uadt,
@@ -301,6 +308,7 @@
 	.head	= mtype_head,
 	.list	= mtype_list,
 	.same_set = mtype_same_set,
+	.cancel_gc = mtype_cancel_gc,
 };
 
 #endif /* __IP_SET_BITMAP_IP_GEN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_bitmap_ip.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_bitmap_ip.c
@@ -163,11 +163,8 @@
 		ret = ip_set_get_hostipaddr4(tb[IPSET_ATTR_IP_TO], &ip_to);
 		if (ret)
 			return ret;
-		if (ip > ip_to) {
+		if (ip > ip_to)
 			swap(ip, ip_to);
-			if (ip < map->first_ip)
-				return -IPSET_ERR_BITMAP_RANGE;
-		}
 	} else if (tb[IPSET_ATTR_CIDR]) {
 		u8 cidr = nla_get_u8(tb[IPSET_ATTR_CIDR]);
 
@@ -178,7 +175,7 @@
 		ip_to = ip;
 	}
 
-	if (ip_to > map->last_ip)
+	if (ip < map->first_ip || ip_to > map->last_ip)
 		return -IPSET_ERR_BITMAP_RANGE;
 
 	for (; !before(ip_to, ip); ip += map->hosts) {
@@ -308,8 +305,8 @@
 			return -IPSET_ERR_BITMAP_RANGE;
 
 		pr_debug("mask_bits %u, netmask %u\n", mask_bits, netmask);
-		hosts = 2 << (32 - netmask - 1);
-		elements = 2 << (netmask - mask_bits - 1);
+		hosts = 2U << (32 - netmask - 1);
+		elements = 2UL << (netmask - mask_bits - 1);
 	}
 	if (elements > IPSET_BITMAP_MAX_RANGE + 1)
 		return -IPSET_ERR_BITMAP_RANGE_SIZE;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_core.c
@@ -53,14 +53,17 @@
 MODULE_ALIAS_NFNL_SUBSYS(NFNL_SUBSYS_IPSET);
 
 /* When the nfnl mutex or ip_set_ref_lock is held: */
-#define ip_set_dereference(p)		\
-	rcu_dereference_protected(p,	\
+#define ip_set_dereference(inst)	\
+	rcu_dereference_protected((inst)->ip_set_list,	\
 		lockdep_nfnl_is_held(NFNL_SUBSYS_IPSET) || \
-		lockdep_is_held(&ip_set_ref_lock))
+		lockdep_is_held(&ip_set_ref_lock) || \
+		(inst)->is_deleted)
 #define ip_set(inst, id)		\
-	ip_set_dereference((inst)->ip_set_list)[id]
+	ip_set_dereference(inst)[id]
 #define ip_set_ref_netlink(inst,id)	\
 	rcu_dereference_raw((inst)->ip_set_list)[id]
+#define ip_set_dereference_nfnl(p)	\
+	rcu_dereference_check(p, lockdep_nfnl_is_held(NFNL_SUBSYS_IPSET))
 
 /* The set types are implemented in modules and registered set types
  * can be found in ip_set_type_list. Adding/deleting types is
@@ -101,14 +104,19 @@
 static bool
 load_settype(const char *name)
 {
+	if (!try_module_get(THIS_MODULE))
+		return false;
+
 	nfnl_unlock(NFNL_SUBSYS_IPSET);
 	pr_debug("try to load ip_set_%s\n", name);
 	if (request_module("ip_set_%s", name) < 0) {
 		pr_warn("Can't find ip_set type %s\n", name);
 		nfnl_lock(NFNL_SUBSYS_IPSET);
+		module_put(THIS_MODULE);
 		return false;
 	}
 	nfnl_lock(NFNL_SUBSYS_IPSET);
+	module_put(THIS_MODULE);
 	return true;
 }
 
@@ -683,6 +691,14 @@
  * a separate reference counter
  */
 static void
+__ip_set_get_netlink(struct ip_set *set)
+{
+	write_lock_bh(&ip_set_ref_lock);
+	set->ref_netlink++;
+	write_unlock_bh(&ip_set_ref_lock);
+}
+
+static void
 __ip_set_put_netlink(struct ip_set *set)
 {
 	write_lock_bh(&ip_set_ref_lock);
@@ -700,15 +716,10 @@
 static struct ip_set *
 ip_set_rcu_get(struct net *net, ip_set_id_t index)
 {
-	struct ip_set *set;
 	struct ip_set_net *inst = ip_set_pernet(net);
 
-	rcu_read_lock();
-	/* ip_set_list itself needs to be protected */
-	set = rcu_dereference(inst->ip_set_list)[index];
-	rcu_read_unlock();
-
-	return set;
+	/* ip_set_list and the set pointer need to be protected */
+	return ip_set_dereference_nfnl(inst->ip_set_list)[index];
 }
 
 static inline void
@@ -1130,7 +1141,7 @@
 		if (!list)
 			goto cleanup;
 		/* nfnl mutex is held, both lists are valid */
-		tmp = ip_set_dereference(inst->ip_set_list);
+		tmp = ip_set_dereference(inst);
 		memcpy(list, tmp, sizeof(struct ip_set *) * inst->ip_set_max);
 		rcu_assign_pointer(inst->ip_set_list, list);
 		/* Make sure all current packets have passed through */
@@ -1151,6 +1162,7 @@
 	return ret;
 
 cleanup:
+	set->variant->cancel_gc(set);
 	set->variant->destroy(set);
 put_out:
 	module_put(set->type->me);
@@ -1168,17 +1180,52 @@
 				    .len = IPSET_MAXNAMELEN - 1 },
 };
 
+/* In order to return quickly when destroying a single set, it is split
+ * into two stages:
+ * - Cancel garbage collector
+ * - Destroy the set itself via call_rcu()
+ */
+
 static void
-ip_set_destroy_set(struct ip_set *set)
+ip_set_destroy_set_rcu(struct rcu_head *head)
 {
-	pr_debug("set: %s\n",  set->name);
+	struct ip_set *set = container_of(head, struct ip_set, rcu);
 
-	/* Must call it without holding any lock */
 	set->variant->destroy(set);
 	module_put(set->type->me);
 	kfree(set);
 }
 
+static void
+_destroy_all_sets(struct ip_set_net *inst)
+{
+	struct ip_set *set;
+	ip_set_id_t i;
+	bool need_wait = false;
+
+	/* First cancel gc's: set:list sets are flushed as well */
+	for (i = 0; i < inst->ip_set_max; i++) {
+		set = ip_set(inst, i);
+		if (set) {
+			set->variant->cancel_gc(set);
+			if (set->type->features & IPSET_TYPE_NAME)
+				need_wait = true;
+		}
+	}
+	/* Must wait for flush to be really finished  */
+	if (need_wait)
+		rcu_barrier();
+	for (i = 0; i < inst->ip_set_max; i++) {
+		set = ip_set(inst, i);
+		if (set) {
+			ip_set(inst, i) = NULL;
+			set->variant->destroy(set);
+			module_put(set->type->me);
+			kfree(set);
+		}
+	}
+}
+
 static int ip_set_destroy(struct sk_buff *skb, const struct nfnl_info *info,
 			  const struct nlattr * const attr[])
 {
@@ -1190,21 +1237,18 @@
 	if (unlikely(protocol_min_failed(attr)))
 		return -IPSET_ERR_PROTOCOL;
 
-	/* Must wait for flush to be really finished in list:set */
-	rcu_barrier();
-
 	/* Commands are serialized and references are
 	 * protected by the ip_set_ref_lock.
 	 * External systems (i.e. xt_set) must call
-	 * ip_set_put|get_nfnl_* functions, that way we
+	 * ip_set_nfnl_get_* functions, that way we
 	 * can safely check references here.
 	 *
 	 * list:set timer can only decrement the reference
 	 * counter, so if it's already zero, we can proceed
 	 * without holding the lock.
 	 */
-	read_lock_bh(&ip_set_ref_lock);
 	if (!attr[IPSET_ATTR_SETNAME]) {
+		read_lock_bh(&ip_set_ref_lock);
 		for (i = 0; i < inst->ip_set_max; i++) {
 			s = ip_set(inst, i);
 			if (s && (s->ref || s->ref_netlink)) {
@@ -1214,17 +1258,14 @@
 		}
 		inst->is_destroyed = true;
 		read_unlock_bh(&ip_set_ref_lock);
-		for (i = 0; i < inst->ip_set_max; i++) {
-			s = ip_set(inst, i);
-			if (s) {
-				ip_set(inst, i) = NULL;
-				ip_set_destroy_set(s);
-			}
-		}
+		_destroy_all_sets(inst);
 		/* Modified by ip_set_destroy() only, which is serialized */
 		inst->is_destroyed = false;
 	} else {
 		u32 flags = flag_exist(info->nlh);
+		u16 features = 0;
+
+		read_lock_bh(&ip_set_ref_lock);
 		s = find_set_and_id(inst, nla_data(attr[IPSET_ATTR_SETNAME]),
 				    &i);
 		if (!s) {
@@ -1235,10 +1276,16 @@
 			ret = -IPSET_ERR_BUSY;
 			goto out;
 		}
+		features = s->type->features;
 		ip_set(inst, i) = NULL;
 		read_unlock_bh(&ip_set_ref_lock);
-
-		ip_set_destroy_set(s);
+		/* Must cancel garbage collectors */
+		s->variant->cancel_gc(s);
+		if (features & IPSET_TYPE_NAME) {
+			/* Must wait for flush to be really finished  */
+			rcu_barrier();
+		}
+		call_rcu(&s->rcu, ip_set_destroy_set_rcu);
 	}
 	return 0;
 out:
@@ -1694,13 +1741,22 @@
 	bool eexist = flags & IPSET_FLAG_EXIST, retried = false;
 
 	do {
+		if (retried) {
+			__ip_set_get_netlink(set);
+			nfnl_unlock(NFNL_SUBSYS_IPSET);
+			cond_resched();
+			nfnl_lock(NFNL_SUBSYS_IPSET);
+			__ip_set_put_netlink(set);
+		}
+
 		ip_set_lock(set);
 		ret = set->variant->uadt(set, tb, adt, &lineno, flags, retried);
 		ip_set_unlock(set);
 		retried = true;
-	} while (ret == -EAGAIN &&
-		 set->variant->resize &&
-		 (ret = set->variant->resize(set, retried)) == 0);
+	} while (ret == -ERANGE ||
+		 (ret == -EAGAIN &&
+		  set->variant->resize &&
+		  (ret = set->variant->resize(set, retried)) == 0));
 
 	if (!ret || (ret == -IPSET_ERR_EXIST && eexist))
 		return 0;
@@ -2331,29 +2387,25 @@
 }
 
 static void __net_exit
-ip_set_net_exit(struct net *net)
+ip_set_net_pre_exit(struct net *net)
 {
 	struct ip_set_net *inst = ip_set_pernet(net);
 
-	struct ip_set *set = NULL;
-	ip_set_id_t i;
-
 	inst->is_deleted = true; /* flag for ip_set_nfnl_put */
+}
 
-	nfnl_lock(NFNL_SUBSYS_IPSET);
-	for (i = 0; i < inst->ip_set_max; i++) {
-		set = ip_set(inst, i);
-		if (set) {
-			ip_set(inst, i) = NULL;
-			ip_set_destroy_set(set);
-		}
-	}
-	nfnl_unlock(NFNL_SUBSYS_IPSET);
+static void __net_exit
+ip_set_net_exit(struct net *net)
+{
+	struct ip_set_net *inst = ip_set_pernet(net);
+
+	_destroy_all_sets(inst);
 	kvfree(rcu_dereference_protected(inst->ip_set_list, 1));
 }
 
 static struct pernet_operations ip_set_net_ops = {
 	.init	= ip_set_net_init,
+	.pre_exit = ip_set_net_pre_exit,
 	.exit   = ip_set_net_exit,
 	.id	= &ip_set_net_id,
 	.size	= sizeof(struct ip_set_net),
@@ -2392,8 +2444,11 @@
 {
 	nf_unregister_sockopt(&so_set);
 	nfnetlink_subsys_unregister(&ip_set_netlink_subsys);
-
 	unregister_pernet_subsys(&ip_set_net_ops);
+
+	/* Wait for call_rcu() in destroy */
+	rcu_barrier();
+
 	pr_debug("these are the famous last words\n");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_gen.h
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_gen.h
@@ -42,31 +42,8 @@
 #define AHASH_MAX_SIZE			(6 * AHASH_INIT_SIZE)
 /* Max muber of elements in the array block when tuned */
 #define AHASH_MAX_TUNED			64
-
 #define AHASH_MAX(h)			((h)->bucketsize)
 
-/* Max number of elements can be tuned */
-#ifdef IP_SET_HASH_WITH_MULTI
-static u8
-tune_bucketsize(u8 curr, u32 multi)
-{
-	u32 n;
-
-	if (multi < curr)
-		return curr;
-
-	n = curr + AHASH_INIT_SIZE;
-	/* Currently, at listing one hash bucket must fit into a message.
-	 * Therefore we have a hard limit here.
-	 */
-	return n > curr && n <= AHASH_MAX_TUNED ? n : curr;
-}
-#define TUNE_BUCKETSIZE(h, multi)	\
-	((h)->bucketsize = tune_bucketsize((h)->bucketsize, multi))
-#else
-#define TUNE_BUCKETSIZE(h, multi)
-#endif
-
 /* A hash bucket */
 struct hbucket {
 	struct rcu_head rcu;	/* for call_rcu */
@@ -233,6 +210,7 @@
 #undef mtype_gc_do
 #undef mtype_gc
 #undef mtype_gc_init
+#undef mtype_cancel_gc
 #undef mtype_variant
 #undef mtype_data_match
 
@@ -277,6 +255,7 @@
 #define mtype_gc_do		IPSET_TOKEN(MTYPE, _gc_do)
 #define mtype_gc		IPSET_TOKEN(MTYPE, _gc)
 #define mtype_gc_init		IPSET_TOKEN(MTYPE, _gc_init)
+#define mtype_cancel_gc		IPSET_TOKEN(MTYPE, _cancel_gc)
 #define mtype_variant		IPSET_TOKEN(MTYPE, _variant)
 #define mtype_data_match	IPSET_TOKEN(MTYPE, _data_match)
 
@@ -440,7 +419,7 @@
 	u32 i;
 
 	for (i = 0; i < jhash_size(t->htable_bits); i++) {
-		n = __ipset_dereference(hbucket(t, i));
+		n = (__force struct hbucket *)hbucket(t, i);
 		if (!n)
 			continue;
 		if (set->extensions & IPSET_EXT_DESTROY && ext_destroy)
@@ -460,10 +439,7 @@
 	struct htype *h = set->data;
 	struct list_head *l, *lt;
 
-	if (SET_WITH_TIMEOUT(set))
-		cancel_delayed_work_sync(&h->gc.dwork);
-
-	mtype_ahash_destroy(set, ipset_dereference_nfnl(h->table), true);
+	mtype_ahash_destroy(set, (__force struct htable *)h->table, true);
 	list_for_each_safe(l, lt, &h->ad) {
 		list_del(l);
 		kfree(l);
@@ -609,6 +585,15 @@
 	queue_delayed_work(system_power_efficient_wq, &gc->dwork, HZ);
 }
 
+static void
+mtype_cancel_gc(struct ip_set *set)
+{
+	struct htype *h = set->data;
+
+	if (SET_WITH_TIMEOUT(set))
+		cancel_delayed_work_sync(&h->gc.dwork);
+}
+
 static int
 mtype_add(struct ip_set *set, void *value, const struct ip_set_ext *ext,
 	  struct ip_set_ext *mext, u32 flags);
@@ -936,7 +921,12 @@
 		goto set_full;
 	/* Create a new slot */
 	if (n->pos >= n->size) {
-		TUNE_BUCKETSIZE(h, multi);
+#ifdef IP_SET_HASH_WITH_MULTI
+		if (h->bucketsize >= AHASH_MAX_TUNED)
+			goto set_full;
+		else if (h->bucketsize <= multi)
+			h->bucketsize += AHASH_INIT_SIZE;
+#endif
 		if (n->size >= AHASH_MAX(h)) {
 			/* Trigger rehashing */
 			mtype_data_next(&h->next, d);
@@ -1434,6 +1424,7 @@
 	.uref	= mtype_uref,
 	.resize	= mtype_resize,
 	.same_set = mtype_same_set,
+	.cancel_gc = mtype_cancel_gc,
 	.region_lock = true,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_ip.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_ip.c
@@ -98,11 +98,11 @@
 hash_ip4_uadt(struct ip_set *set, struct nlattr *tb[],
 	      enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_ip4 *h = set->data;
+	struct hash_ip4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_ip4_elem e = { 0 };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 ip = 0, ip_to = 0, hosts;
+	u32 ip = 0, ip_to = 0, hosts, i = 0;
 	int ret = 0;
 
 	if (tb[IPSET_ATTR_LINENO])
@@ -147,22 +147,20 @@
 
 	hosts = h->netmask == 32 ? 1 : 2 << (32 - h->netmask - 1);
 
-	/* 64bit division is not allowed on 32bit */
-	if (((u64)ip_to - ip + 1) >> (32 - h->netmask) > IPSET_MAX_RANGE)
-		return -ERANGE;
-
-	if (retried) {
+	if (retried)
 		ip = ntohl(h->next.ip);
+	for (; ip <= ip_to; i++) {
 		e.ip = htonl(ip);
-	}
-	for (; ip <= ip_to;) {
+		if (i > IPSET_MAX_RANGE) {
+			hash_ip4_data_next(&h->next, &e);
+			return -ERANGE;
+		}
 		ret = adtfn(set, &e, &ext, &ext, flags);
 		if (ret && !ip_set_eexist(ret, flags))
 			return ret;
 
 		ip += hosts;
-		e.ip = htonl(ip);
-		if (e.ip == 0)
+		if (ip == 0)
 			return 0;
 
 		ret = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_ipmark.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_ipmark.c
@@ -97,11 +97,11 @@
 hash_ipmark4_uadt(struct ip_set *set, struct nlattr *tb[],
 		  enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_ipmark4 *h = set->data;
+	struct hash_ipmark4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_ipmark4_elem e = { };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 ip, ip_to = 0;
+	u32 ip, ip_to = 0, i = 0;
 	int ret;
 
 	if (tb[IPSET_ATTR_LINENO])
@@ -148,13 +148,14 @@
 		ip_set_mask_from_to(ip, ip_to, cidr);
 	}
 
-	if (((u64)ip_to - ip + 1) > IPSET_MAX_RANGE)
-		return -ERANGE;
-
 	if (retried)
 		ip = ntohl(h->next.ip);
-	for (; ip <= ip_to; ip++) {
+	for (; ip <= ip_to; ip++, i++) {
 		e.ip = htonl(ip);
+		if (i > IPSET_MAX_RANGE) {
+			hash_ipmark4_data_next(&h->next, &e);
+			return -ERANGE;
+		}
 		ret = adtfn(set, &e, &ext, &ext, flags);
 
 		if (ret && !ip_set_eexist(ret, flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_ipport.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_ipport.c
@@ -105,11 +105,11 @@
 hash_ipport4_uadt(struct ip_set *set, struct nlattr *tb[],
 		  enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_ipport4 *h = set->data;
+	struct hash_ipport4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_ipport4_elem e = { .ip = 0 };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 ip, ip_to = 0, p = 0, port, port_to;
+	u32 ip, ip_to = 0, p = 0, port, port_to, i = 0;
 	bool with_ports = false;
 	int ret;
 
@@ -173,17 +173,18 @@
 			swap(port, port_to);
 	}
 
-	if (((u64)ip_to - ip + 1)*(port_to - port + 1) > IPSET_MAX_RANGE)
-		return -ERANGE;
-
 	if (retried)
 		ip = ntohl(h->next.ip);
 	for (; ip <= ip_to; ip++) {
 		p = retried && ip == ntohl(h->next.ip) ? ntohs(h->next.port)
 						       : port;
-		for (; p <= port_to; p++) {
+		for (; p <= port_to; p++, i++) {
 			e.ip = htonl(ip);
 			e.port = htons(p);
+			if (i > IPSET_MAX_RANGE) {
+				hash_ipport4_data_next(&h->next, &e);
+				return -ERANGE;
+			}
 			ret = adtfn(set, &e, &ext, &ext, flags);
 
 			if (ret && !ip_set_eexist(ret, flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_ipportip.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_ipportip.c
@@ -108,11 +108,11 @@
 hash_ipportip4_uadt(struct ip_set *set, struct nlattr *tb[],
 		    enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_ipportip4 *h = set->data;
+	struct hash_ipportip4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_ipportip4_elem e = { .ip = 0 };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 ip, ip_to = 0, p = 0, port, port_to;
+	u32 ip, ip_to = 0, p = 0, port, port_to, i = 0;
 	bool with_ports = false;
 	int ret;
 
@@ -180,17 +180,18 @@
 			swap(port, port_to);
 	}
 
-	if (((u64)ip_to - ip + 1)*(port_to - port + 1) > IPSET_MAX_RANGE)
-		return -ERANGE;
-
 	if (retried)
 		ip = ntohl(h->next.ip);
 	for (; ip <= ip_to; ip++) {
 		p = retried && ip == ntohl(h->next.ip) ? ntohs(h->next.port)
 						       : port;
-		for (; p <= port_to; p++) {
+		for (; p <= port_to; p++, i++) {
 			e.ip = htonl(ip);
 			e.port = htons(p);
+			if (i > IPSET_MAX_RANGE) {
+				hash_ipportip4_data_next(&h->next, &e);
+				return -ERANGE;
+			}
 			ret = adtfn(set, &e, &ext, &ext, flags);
 
 			if (ret && !ip_set_eexist(ret, flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_ipportnet.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_ipportnet.c
@@ -160,12 +160,12 @@
 hash_ipportnet4_uadt(struct ip_set *set, struct nlattr *tb[],
 		     enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_ipportnet4 *h = set->data;
+	struct hash_ipportnet4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_ipportnet4_elem e = { .cidr = HOST_MASK - 1 };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
 	u32 ip = 0, ip_to = 0, p = 0, port, port_to;
-	u32 ip2_from = 0, ip2_to = 0, ip2;
+	u32 ip2_from = 0, ip2_to = 0, ip2, i = 0;
 	bool with_ports = false;
 	u8 cidr;
 	int ret;
@@ -253,9 +253,6 @@
 			swap(port, port_to);
 	}
 
-	if (((u64)ip_to - ip + 1)*(port_to - port + 1) > IPSET_MAX_RANGE)
-		return -ERANGE;
-
 	ip2_to = ip2_from;
 	if (tb[IPSET_ATTR_IP2_TO]) {
 		ret = ip_set_get_hostipaddr4(tb[IPSET_ATTR_IP2_TO], &ip2_to);
@@ -282,9 +279,15 @@
 		for (; p <= port_to; p++) {
 			e.port = htons(p);
 			do {
+				i++;
 				e.ip2 = htonl(ip2);
 				ip2 = ip_set_range_to_cidr(ip2, ip2_to, &cidr);
 				e.cidr = cidr - 1;
+				if (i > IPSET_MAX_RANGE) {
+					hash_ipportnet4_data_next(&h->next,
+								  &e);
+					return -ERANGE;
+				}
 				ret = adtfn(set, &e, &ext, &ext, flags);
 
 				if (ret && !ip_set_eexist(ret, flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_net.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_net.c
@@ -136,11 +136,11 @@
 hash_net4_uadt(struct ip_set *set, struct nlattr *tb[],
 	       enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_net4 *h = set->data;
+	struct hash_net4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_net4_elem e = { .cidr = HOST_MASK };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 ip = 0, ip_to = 0, ipn, n = 0;
+	u32 ip = 0, ip_to = 0, i = 0;
 	int ret;
 
 	if (tb[IPSET_ATTR_LINENO])
@@ -188,19 +188,16 @@
 		if (ip + UINT_MAX == ip_to)
 			return -IPSET_ERR_HASH_RANGE;
 	}
-	ipn = ip;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip_to, &e.cidr);
-		n++;
-	} while (ipn++ < ip_to);
-
-	if (n > IPSET_MAX_RANGE)
-		return -ERANGE;
 
 	if (retried)
 		ip = ntohl(h->next.ip);
 	do {
+		i++;
 		e.ip = htonl(ip);
+		if (i > IPSET_MAX_RANGE) {
+			hash_net4_data_next(&h->next, &e);
+			return -ERANGE;
+		}
 		ip = ip_set_range_to_cidr(ip, ip_to, &e.cidr);
 		ret = adtfn(set, &e, &ext, &ext, flags);
 		if (ret && !ip_set_eexist(ret, flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_netiface.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_netiface.c
@@ -202,7 +202,7 @@
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_netiface4_elem e = { .cidr = HOST_MASK, .elem = 1 };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 ip = 0, ip_to = 0, ipn, n = 0;
+	u32 ip = 0, ip_to = 0, i = 0;
 	int ret;
 
 	if (tb[IPSET_ATTR_LINENO])
@@ -256,19 +256,16 @@
 	} else {
 		ip_set_mask_from_to(ip, ip_to, e.cidr);
 	}
-	ipn = ip;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip_to, &e.cidr);
-		n++;
-	} while (ipn++ < ip_to);
-
-	if (n > IPSET_MAX_RANGE)
-		return -ERANGE;
 
 	if (retried)
 		ip = ntohl(h->next.ip);
 	do {
+		i++;
 		e.ip = htonl(ip);
+		if (i > IPSET_MAX_RANGE) {
+			hash_netiface4_data_next(&h->next, &e);
+			return -ERANGE;
+		}
 		ip = ip_set_range_to_cidr(ip, ip_to, &e.cidr);
 		ret = adtfn(set, &e, &ext, &ext, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_netnet.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_netnet.c
@@ -163,13 +163,12 @@
 hash_netnet4_uadt(struct ip_set *set, struct nlattr *tb[],
 		  enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_netnet4 *h = set->data;
+	struct hash_netnet4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_netnet4_elem e = { };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
 	u32 ip = 0, ip_to = 0;
-	u32 ip2 = 0, ip2_from = 0, ip2_to = 0, ipn;
-	u64 n = 0, m = 0;
+	u32 ip2 = 0, ip2_from = 0, ip2_to = 0, i = 0;
 	int ret;
 
 	if (tb[IPSET_ATTR_LINENO])
@@ -245,19 +244,6 @@
 	} else {
 		ip_set_mask_from_to(ip2_from, ip2_to, e.cidr[1]);
 	}
-	ipn = ip;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip_to, &e.cidr[0]);
-		n++;
-	} while (ipn++ < ip_to);
-	ipn = ip2_from;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip2_to, &e.cidr[1]);
-		m++;
-	} while (ipn++ < ip2_to);
-
-	if (n*m > IPSET_MAX_RANGE)
-		return -ERANGE;
 
 	if (retried) {
 		ip = ntohl(h->next.ip[0]);
@@ -270,7 +256,12 @@
 		e.ip[0] = htonl(ip);
 		ip = ip_set_range_to_cidr(ip, ip_to, &e.cidr[0]);
 		do {
+			i++;
 			e.ip[1] = htonl(ip2);
+			if (i > IPSET_MAX_RANGE) {
+				hash_netnet4_data_next(&h->next, &e);
+				return -ERANGE;
+			}
 			ip2 = ip_set_range_to_cidr(ip2, ip2_to, &e.cidr[1]);
 			ret = adtfn(set, &e, &ext, &ext, flags);
 			if (ret && !ip_set_eexist(ret, flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_netport.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_netport.c
@@ -154,12 +154,11 @@
 hash_netport4_uadt(struct ip_set *set, struct nlattr *tb[],
 		   enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_netport4 *h = set->data;
+	struct hash_netport4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_netport4_elem e = { .cidr = HOST_MASK - 1 };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
-	u32 port, port_to, p = 0, ip = 0, ip_to = 0, ipn;
-	u64 n = 0;
+	u32 port, port_to, p = 0, ip = 0, ip_to = 0, i = 0;
 	bool with_ports = false;
 	u8 cidr;
 	int ret;
@@ -236,14 +235,6 @@
 	} else {
 		ip_set_mask_from_to(ip, ip_to, e.cidr + 1);
 	}
-	ipn = ip;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip_to, &cidr);
-		n++;
-	} while (ipn++ < ip_to);
-
-	if (n*(port_to - port + 1) > IPSET_MAX_RANGE)
-		return -ERANGE;
 
 	if (retried) {
 		ip = ntohl(h->next.ip);
@@ -255,8 +246,12 @@
 		e.ip = htonl(ip);
 		ip = ip_set_range_to_cidr(ip, ip_to, &cidr);
 		e.cidr = cidr - 1;
-		for (; p <= port_to; p++) {
+		for (; p <= port_to; p++, i++) {
 			e.port = htons(p);
+			if (i > IPSET_MAX_RANGE) {
+				hash_netport4_data_next(&h->next, &e);
+				return -ERANGE;
+			}
 			ret = adtfn(set, &e, &ext, &ext, flags);
 			if (ret && !ip_set_eexist(ret, flags))
 				return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_hash_netportnet.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_hash_netportnet.c
@@ -36,6 +36,7 @@
 #define IP_SET_HASH_WITH_PROTO
 #define IP_SET_HASH_WITH_NETS
 #define IPSET_NET_COUNT 2
+#define IP_SET_HASH_WITH_NET0
 
 /* IPv4 variant */
 
@@ -173,17 +174,26 @@
 	return adtfn(set, &e, &ext, &opt->ext, opt->cmdflags);
 }
 
+static u32
+hash_netportnet4_range_to_cidr(u32 from, u32 to, u8 *cidr)
+{
+	if (from == 0 && to == UINT_MAX) {
+		*cidr = 0;
+		return to;
+	}
+	return ip_set_range_to_cidr(from, to, cidr);
+}
+
 static int
 hash_netportnet4_uadt(struct ip_set *set, struct nlattr *tb[],
 		      enum ipset_adt adt, u32 *lineno, u32 flags, bool retried)
 {
-	const struct hash_netportnet4 *h = set->data;
+	struct hash_netportnet4 *h = set->data;
 	ipset_adtfn adtfn = set->variant->adt[adt];
 	struct hash_netportnet4_elem e = { };
 	struct ip_set_ext ext = IP_SET_INIT_UEXT(set);
 	u32 ip = 0, ip_to = 0, p = 0, port, port_to;
-	u32 ip2_from = 0, ip2_to = 0, ip2, ipn;
-	u64 n = 0, m = 0;
+	u32 ip2_from = 0, ip2_to = 0, ip2, i = 0;
 	bool with_ports = false;
 	int ret;
 
@@ -285,19 +295,6 @@
 	} else {
 		ip_set_mask_from_to(ip2_from, ip2_to, e.cidr[1]);
 	}
-	ipn = ip;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip_to, &e.cidr[0]);
-		n++;
-	} while (ipn++ < ip_to);
-	ipn = ip2_from;
-	do {
-		ipn = ip_set_range_to_cidr(ipn, ip2_to, &e.cidr[1]);
-		m++;
-	} while (ipn++ < ip2_to);
-
-	if (n*m*(port_to - port + 1) > IPSET_MAX_RANGE)
-		return -ERANGE;
 
 	if (retried) {
 		ip = ntohl(h->next.ip[0]);
@@ -310,13 +307,19 @@
 
 	do {
 		e.ip[0] = htonl(ip);
-		ip = ip_set_range_to_cidr(ip, ip_to, &e.cidr[0]);
+		ip = hash_netportnet4_range_to_cidr(ip, ip_to, &e.cidr[0]);
 		for (; p <= port_to; p++) {
 			e.port = htons(p);
 			do {
+				i++;
 				e.ip[1] = htonl(ip2);
-				ip2 = ip_set_range_to_cidr(ip2, ip2_to,
-							   &e.cidr[1]);
+				if (i > IPSET_MAX_RANGE) {
+					hash_netportnet4_data_next(&h->next,
+								   &e);
+					return -ERANGE;
+				}
+				ip2 = hash_netportnet4_range_to_cidr(ip2,
+							ip2_to, &e.cidr[1]);
 				ret = adtfn(set, &e, &ext, &ext, flags);
 				if (ret && !ip_set_eexist(ret, flags))
 					return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipset/ip_set_list_set.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipset/ip_set_list_set.c
@@ -79,7 +79,7 @@
 	struct set_elem *e;
 	int ret;
 
-	list_for_each_entry(e, &map->members, list) {
+	list_for_each_entry_rcu(e, &map->members, list) {
 		if (SET_WITH_TIMEOUT(set) &&
 		    ip_set_timeout_expired(ext_timeout(e, set)))
 			continue;
@@ -99,7 +99,7 @@
 	struct set_elem *e;
 	int ret;
 
-	list_for_each_entry(e, &map->members, list) {
+	list_for_each_entry_rcu(e, &map->members, list) {
 		if (SET_WITH_TIMEOUT(set) &&
 		    ip_set_timeout_expired(ext_timeout(e, set)))
 			continue;
@@ -188,9 +188,10 @@
 	struct list_set *map = set->data;
 	struct set_adt_elem *d = value;
 	struct set_elem *e, *next, *prev = NULL;
-	int ret;
+	int ret = 0;
 
-	list_for_each_entry(e, &map->members, list) {
+	rcu_read_lock();
+	list_for_each_entry_rcu(e, &map->members, list) {
 		if (SET_WITH_TIMEOUT(set) &&
 		    ip_set_timeout_expired(ext_timeout(e, set)))
 			continue;
@@ -201,6 +202,7 @@
 
 		if (d->before == 0) {
 			ret = 1;
+			goto out;
 		} else if (d->before > 0) {
 			next = list_next_entry(e, list);
 			ret = !list_is_last(&e->list, &map->members) &&
@@ -208,9 +210,11 @@
 		} else {
 			ret = prev && prev->id == d->refid;
 		}
-		return ret;
+		goto out;
 	}
-	return 0;
+out:
+	rcu_read_unlock();
+	return ret;
 }
 
 static void
@@ -239,7 +243,7 @@
 
 	/* Find where to add the new entry */
 	n = prev = next = NULL;
-	list_for_each_entry(e, &map->members, list) {
+	list_for_each_entry_rcu(e, &map->members, list) {
 		if (SET_WITH_TIMEOUT(set) &&
 		    ip_set_timeout_expired(ext_timeout(e, set)))
 			continue;
@@ -316,9 +320,9 @@
 {
 	struct list_set *map = set->data;
 	struct set_adt_elem *d = value;
-	struct set_elem *e, *next, *prev = NULL;
+	struct set_elem *e, *n, *next, *prev = NULL;
 
-	list_for_each_entry(e, &map->members, list) {
+	list_for_each_entry_safe(e, n, &map->members, list) {
 		if (SET_WITH_TIMEOUT(set) &&
 		    ip_set_timeout_expired(ext_timeout(e, set)))
 			continue;
@@ -424,17 +428,8 @@
 list_set_destroy(struct ip_set *set)
 {
 	struct list_set *map = set->data;
-	struct set_elem *e, *n;
 
-	if (SET_WITH_TIMEOUT(set))
-		del_timer_sync(&map->gc);
-
-	list_for_each_entry_safe(e, n, &map->members, list) {
-		list_del(&e->list);
-		ip_set_put_byindex(map->net, e->id);
-		ip_set_ext_destroy(set, e);
-		kfree(e);
-	}
+	WARN_ON_ONCE(!list_empty(&map->members));
 	kfree(map);
 
 	set->data = NULL;
@@ -545,6 +540,18 @@
 	       a->extensions == b->extensions;
 }
 
+static void
+list_set_cancel_gc(struct ip_set *set)
+{
+	struct list_set *map = set->data;
+
+	if (SET_WITH_TIMEOUT(set))
+		del_timer_sync(&map->gc);
+
+	/* Flush list to drop references to other ipsets */
+	list_set_flush(set);
+}
+
 static const struct ip_set_type_variant set_variant = {
 	.kadt	= list_set_kadt,
 	.uadt	= list_set_uadt,
@@ -558,6 +565,7 @@
 	.head	= list_set_head,
 	.list	= list_set_list,
 	.same_set = list_set_same_set,
+	.cancel_gc = list_set_cancel_gc,
 };
 
 static void
@@ -603,6 +611,8 @@
 	return true;
 }
 
+static struct lock_class_key list_set_lockdep_key;
+
 static int
 list_set_create(struct net *net, struct ip_set *set, struct nlattr *tb[],
 		u32 flags)
@@ -619,6 +629,7 @@
 	if (size < IP_SET_LIST_MIN_SIZE)
 		size = IP_SET_LIST_MIN_SIZE;
 
+	lockdep_set_class(&set->lock, &list_set_lockdep_key);
 	set->variant = &set_variant;
 	set->dsize = ip_set_elem_len(set, tb, sizeof(struct set_elem),
 				     __alignof__(struct set_elem));
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/Kconfig
@@ -44,7 +44,8 @@
 
 config	IP_VS_TAB_BITS
 	int "IPVS connection table size (the Nth power of 2)"
-	range 8 20
+	range 8 20 if !64BIT
+	range 8 27 if 64BIT
 	default 12
 	help
 	  The IPVS connection hash table uses the chaining scheme to handle
@@ -54,24 +55,24 @@
 
 	  Note the table size must be power of 2. The table size will be the
 	  value of 2 to the your input number power. The number to choose is
-	  from 8 to 20, the default number is 12, which means the table size
-	  is 4096. Don't input the number too small, otherwise you will lose
-	  performance on it. You can adapt the table size yourself, according
-	  to your virtual server application. It is good to set the table size
-	  not far less than the number of connections per second multiplying
-	  average lasting time of connection in the table.  For example, your
-	  virtual server gets 200 connections per second, the connection lasts
-	  for 200 seconds in average in the connection table, the table size
-	  should be not far less than 200x200, it is good to set the table
-	  size 32768 (2**15).
+	  from 8 to 27 for 64BIT(20 otherwise), the default number is 12,
+	  which means the table size is 4096. Don't input the number too
+	  small, otherwise you will lose performance on it. You can adapt the
+	  table size yourself, according to your virtual server application.
+	  It is good to set the table size not far less than the number of
+	  connections per second multiplying average lasting time of
+	  connection in the table.  For example, your virtual server gets 200
+	  connections per second, the connection lasts for 200 seconds in
+	  average in the connection table, the table size should be not far
+	  less than 200x200, it is good to set the table size 32768 (2**15).
 
 	  Another note that each connection occupies 128 bytes effectively and
 	  each hash entry uses 8 bytes, so you can estimate how much memory is
 	  needed for your box.
 
 	  You can overwrite this number setting conn_tab_bits module parameter
-	  or by appending ip_vs.conn_tab_bits=? to the kernel command line
-	  if IP VS was compiled built-in.
+	  or by appending ip_vs.conn_tab_bits=? to the kernel command line if
+	  IP VS was compiled built-in.
 
 comment "IPVS transport protocol load balancing support"
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_app.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_app.c
@@ -599,13 +599,19 @@
 int __net_init ip_vs_app_net_init(struct netns_ipvs *ipvs)
 {
 	INIT_LIST_HEAD(&ipvs->app_list);
-	proc_create_net("ip_vs_app", 0, ipvs->net->proc_net, &ip_vs_app_seq_ops,
-			sizeof(struct seq_net_private));
+#ifdef CONFIG_PROC_FS
+	if (!proc_create_net("ip_vs_app", 0, ipvs->net->proc_net,
+			     &ip_vs_app_seq_ops,
+			     sizeof(struct seq_net_private)))
+		return -ENOMEM;
+#endif
 	return 0;
 }
 
 void __net_exit ip_vs_app_net_cleanup(struct netns_ipvs *ipvs)
 {
 	unregister_ip_vs_app(ipvs, NULL /* all */);
+#ifdef CONFIG_PROC_FS
 	remove_proc_entry("ip_vs_app", ipvs->net->proc_net);
+#endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_conn.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_conn.c
@@ -1265,8 +1265,8 @@
 	 * The drop rate array needs tuning for real environments.
 	 * Called from timer bh only => no locking
 	 */
-	static const char todrop_rate[9] = {0, 1, 2, 3, 4, 5, 6, 7, 8};
-	static char todrop_counter[9] = {0};
+	static const signed char todrop_rate[9] = {0, 1, 2, 3, 4, 5, 6, 7, 8};
+	static signed char todrop_counter[9] = {0};
 	int i;
 
 	/* if the conn entry hasn't lasted for 60 seconds, don't drop it.
@@ -1447,20 +1447,36 @@
 {
 	atomic_set(&ipvs->conn_count, 0);
 
-	proc_create_net("ip_vs_conn", 0, ipvs->net->proc_net,
-			&ip_vs_conn_seq_ops, sizeof(struct ip_vs_iter_state));
-	proc_create_net("ip_vs_conn_sync", 0, ipvs->net->proc_net,
-			&ip_vs_conn_sync_seq_ops,
-			sizeof(struct ip_vs_iter_state));
+#ifdef CONFIG_PROC_FS
+	if (!proc_create_net("ip_vs_conn", 0, ipvs->net->proc_net,
+			     &ip_vs_conn_seq_ops,
+			     sizeof(struct ip_vs_iter_state)))
+		goto err_conn;
+
+	if (!proc_create_net("ip_vs_conn_sync", 0, ipvs->net->proc_net,
+			     &ip_vs_conn_sync_seq_ops,
+			     sizeof(struct ip_vs_iter_state)))
+		goto err_conn_sync;
+#endif
+
 	return 0;
+
+#ifdef CONFIG_PROC_FS
+err_conn_sync:
+	remove_proc_entry("ip_vs_conn", ipvs->net->proc_net);
+err_conn:
+	return -ENOMEM;
+#endif
 }
 
 void __net_exit ip_vs_conn_net_cleanup(struct netns_ipvs *ipvs)
 {
 	/* flush all the connection entries first */
 	ip_vs_conn_flush(ipvs);
+#ifdef CONFIG_PROC_FS
 	remove_proc_entry("ip_vs_conn", ipvs->net->proc_net);
 	remove_proc_entry("ip_vs_conn_sync", ipvs->net->proc_net);
+#endif
 }
 
 int __init ip_vs_conn_init(void)
@@ -1468,8 +1484,8 @@
 	int idx;
 
 	/* Compute size and mask */
-	if (ip_vs_conn_tab_bits < 8 || ip_vs_conn_tab_bits > 20) {
-		pr_info("conn_tab_bits not in [8, 20]. Using default value\n");
+	if (ip_vs_conn_tab_bits < 8 || ip_vs_conn_tab_bits > 27) {
+		pr_info("conn_tab_bits not in [8, 27]. Using default value\n");
 		ip_vs_conn_tab_bits = CONFIG_IP_VS_TAB_BITS;
 	}
 	ip_vs_conn_tab_size = 1 << ip_vs_conn_tab_bits;
@@ -1495,7 +1511,7 @@
 	pr_info("Connection hash table configured "
 		"(size=%d, memory=%ldKbytes)\n",
 		ip_vs_conn_tab_size,
-		(long)(ip_vs_conn_tab_size*sizeof(struct list_head))/1024);
+		(long)(ip_vs_conn_tab_size*sizeof(*ip_vs_conn_tab))/1024);
 	IP_VS_DBG(0, "Each connection entry needs %zd bytes at least\n",
 		  sizeof(struct ip_vs_conn));
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_core.c
@@ -1964,7 +1964,6 @@
 	struct ip_vs_proto_data *pd;
 	struct ip_vs_conn *cp;
 	int ret, pkts;
-	int conn_reuse_mode;
 	struct sock *sk;
 
 	/* Already marked as IPVS request or reply? */
@@ -2041,15 +2040,16 @@
 	cp = INDIRECT_CALL_1(pp->conn_in_get, ip_vs_conn_in_get_proto,
 			     ipvs, af, skb, &iph);
 
-	conn_reuse_mode = sysctl_conn_reuse_mode(ipvs);
-	if (conn_reuse_mode && !iph.fragoffs && is_new_conn(skb, &iph) && cp) {
+	if (!iph.fragoffs && is_new_conn(skb, &iph) && cp) {
+		int conn_reuse_mode = sysctl_conn_reuse_mode(ipvs);
 		bool old_ct = false, resched = false;
 
 		if (unlikely(sysctl_expire_nodest_conn(ipvs)) && cp->dest &&
 		    unlikely(!atomic_read(&cp->dest->weight))) {
 			resched = true;
 			old_ct = ip_vs_conn_uses_old_conntrack(cp, skb);
-		} else if (is_new_conn_expected(cp, conn_reuse_mode)) {
+		} else if (conn_reuse_mode &&
+			   is_new_conn_expected(cp, conn_reuse_mode)) {
 			old_ct = ip_vs_conn_uses_old_conntrack(cp, skb);
 			if (!atomic_read(&cp->n_control)) {
 				resched = true;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_ctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_ctl.c
@@ -1802,6 +1802,7 @@
 proc_do_sync_threshold(struct ctl_table *table, int write,
 		       void *buffer, size_t *lenp, loff_t *ppos)
 {
+	struct netns_ipvs *ipvs = table->extra2;
 	int *valp = table->data;
 	int val[2];
 	int rc;
@@ -1811,6 +1812,7 @@
 		.mode = table->mode,
 	};
 
+	mutex_lock(&ipvs->sync_mutex);
 	memcpy(val, valp, sizeof(val));
 	rc = proc_dointvec(&tmp, write, buffer, lenp, ppos);
 	if (write) {
@@ -1820,6 +1822,7 @@
 		else
 			memcpy(valp, val, sizeof(val));
 	}
+	mutex_unlock(&ipvs->sync_mutex);
 	return rc;
 }
 
@@ -2849,12 +2852,12 @@
 	case IP_VS_SO_GET_SERVICES:
 	{
 		struct ip_vs_get_services *get;
-		int size;
+		size_t size;
 
 		get = (struct ip_vs_get_services *)arg;
 		size = struct_size(get, entrytable, get->num_services);
 		if (*len != size) {
-			pr_err("length: %u != %u\n", *len, size);
+			pr_err("length: %u != %zu\n", *len, size);
 			ret = -EINVAL;
 			goto out;
 		}
@@ -2890,12 +2893,12 @@
 	case IP_VS_SO_GET_DESTS:
 	{
 		struct ip_vs_get_dests *get;
-		int size;
+		size_t size;
 
 		get = (struct ip_vs_get_dests *)arg;
 		size = struct_size(get, entrytable, get->num_dests);
 		if (*len != size) {
-			pr_err("length: %u != %u\n", *len, size);
+			pr_err("length: %u != %zu\n", *len, size);
 			ret = -EINVAL;
 			goto out;
 		}
@@ -4077,6 +4080,7 @@
 	ipvs->sysctl_sync_threshold[0] = DEFAULT_SYNC_THRESHOLD;
 	ipvs->sysctl_sync_threshold[1] = DEFAULT_SYNC_PERIOD;
 	tbl[idx].data = &ipvs->sysctl_sync_threshold;
+	tbl[idx].extra2 = ipvs;
 	tbl[idx++].maxlen = sizeof(ipvs->sysctl_sync_threshold);
 	ipvs->sysctl_sync_refresh_period = DEFAULT_SYNC_REFRESH_PERIOD;
 	tbl[idx++].data = &ipvs->sysctl_sync_refresh_period;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_proto.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_proto.c
@@ -340,7 +340,7 @@
 
 int __init ip_vs_protocol_init(void)
 {
-	char protocols[64];
+	char protocols[64] = { 0 };
 #define REGISTER_PROTOCOL(p)			\
 	do {					\
 		register_ip_vs_protocol(p);	\
@@ -348,8 +348,6 @@
 		strcat(protocols, (p)->name);	\
 	} while (0)
 
-	protocols[0] = '\0';
-	protocols[2] = '\0';
 #ifdef CONFIG_IP_VS_PROTO_TCP
 	REGISTER_PROTOCOL(&ip_vs_protocol_tcp);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_proto_sctp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_proto_sctp.c
@@ -126,7 +126,8 @@
 	if (sctph->source != cp->vport || payload_csum ||
 	    skb->ip_summed == CHECKSUM_PARTIAL) {
 		sctph->source = cp->vport;
-		sctp_nat_csum(skb, sctph, sctphoff);
+		if (!skb_is_gso(skb))
+			sctp_nat_csum(skb, sctph, sctphoff);
 	} else {
 		skb->ip_summed = CHECKSUM_UNNECESSARY;
 	}
@@ -174,7 +175,8 @@
 	    (skb->ip_summed == CHECKSUM_PARTIAL &&
 	     !(skb_dst(skb)->dev->features & NETIF_F_SCTP_CRC))) {
 		sctph->dest = cp->dport;
-		sctp_nat_csum(skb, sctph, sctphoff);
+		if (!skb_is_gso(skb))
+			sctp_nat_csum(skb, sctph, sctphoff);
 	} else if (skb->ip_summed != CHECKSUM_PARTIAL) {
 		skb->ip_summed = CHECKSUM_UNNECESSARY;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_sync.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_sync.c
@@ -603,7 +603,7 @@
 	if (cp->flags & IP_VS_CONN_F_SEQ_MASK) {
 		struct ip_vs_sync_conn_options *opt =
 			(struct ip_vs_sync_conn_options *)&s[1];
-		memcpy(opt, &cp->in_seq, sizeof(*opt));
+		memcpy(opt, &cp->sync_conn_opt, sizeof(*opt));
 	}
 
 	m->nr_conns++;
@@ -1280,12 +1280,12 @@
 	lock_sock(sk);
 	if (mode) {
 		val = clamp_t(int, val, (SOCK_MIN_SNDBUF + 1) / 2,
-			      sysctl_wmem_max);
+			      READ_ONCE(sysctl_wmem_max));
 		sk->sk_sndbuf = val * 2;
 		sk->sk_userlocks |= SOCK_SNDBUF_LOCK;
 	} else {
 		val = clamp_t(int, val, (SOCK_MIN_RCVBUF + 1) / 2,
-			      sysctl_rmem_max);
+			      READ_ONCE(sysctl_rmem_max));
 		sk->sk_rcvbuf = val * 2;
 		sk->sk_userlocks |= SOCK_RCVBUF_LOCK;
 	}
@@ -1441,7 +1441,7 @@
 	sin.sin_addr.s_addr  = addr;
 	sin.sin_port         = 0;
 
-	return sock->ops->bind(sock, (struct sockaddr*)&sin, sizeof(sin));
+	return kernel_bind(sock, (struct sockaddr *)&sin, sizeof(sin));
 }
 
 static void get_mcast_sockaddr(union ipvs_sockaddr *sa, int *salen,
@@ -1507,8 +1507,8 @@
 	}
 
 	get_mcast_sockaddr(&mcast_addr, &salen, &ipvs->mcfg, id);
-	result = sock->ops->connect(sock, (struct sockaddr *) &mcast_addr,
-				    salen, 0);
+	result = kernel_connect(sock, (struct sockaddr *)&mcast_addr,
+				salen, 0);
 	if (result < 0) {
 		pr_err("Error connecting to the multicast addr\n");
 		goto error;
@@ -1548,7 +1548,7 @@
 
 	get_mcast_sockaddr(&mcast_addr, &salen, &ipvs->bcfg, id);
 	sock->sk->sk_bound_dev_if = dev->ifindex;
-	result = sock->ops->bind(sock, (struct sockaddr *)&mcast_addr, salen);
+	result = kernel_bind(sock, (struct sockaddr *)&mcast_addr, salen);
 	if (result < 0) {
 		pr_err("Error binding to the multicast addr\n");
 		goto error;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/ipvs/ip_vs_xmit.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/ipvs/ip_vs_xmit.c
@@ -271,7 +271,7 @@
 			skb->dev = dst->dev;
 			icmpv6_send(skb, ICMPV6_TIME_EXCEED,
 				    ICMPV6_EXC_HOPLIMIT, 0);
-			__IP6_INC_STATS(net, idev, IPSTATS_MIB_INHDRERRORS);
+			IP6_INC_STATS(net, idev, IPSTATS_MIB_INHDRERRORS);
 
 			return false;
 		}
@@ -286,7 +286,7 @@
 	{
 		if (ip_hdr(skb)->ttl <= 1) {
 			/* Tell the sender its packet died... */
-			__IP_INC_STATS(net, IPSTATS_MIB_INHDRERRORS);
+			IP_INC_STATS(net, IPSTATS_MIB_INHDRERRORS);
 			icmp_send(skb, ICMP_TIME_EXCEEDED, ICMP_EXC_TTL, 0);
 			return false;
 		}
@@ -1225,6 +1225,7 @@
 	skb->transport_header = skb->network_header;
 
 	skb_set_inner_ipproto(skb, next_protocol);
+	skb_set_inner_mac_header(skb, skb_inner_network_offset(skb));
 
 	if (tun_type == IP_VS_CONN_F_TUNNEL_TYPE_GUE) {
 		bool check = false;
@@ -1373,6 +1374,7 @@
 	skb->transport_header = skb->network_header;
 
 	skb_set_inner_ipproto(skb, next_protocol);
+	skb_set_inner_mac_header(skb, skb_inner_network_offset(skb));
 
 	if (tun_type == IP_VS_CONN_F_TUNNEL_TYPE_GUE) {
 		bool check = false;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conncount.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conncount.c
@@ -310,7 +310,6 @@
 	struct nf_conncount_rb *rbconn;
 	struct nf_conncount_tuple *conn;
 	unsigned int count = 0, gc_count = 0;
-	u8 keylen = data->keylen;
 	bool do_gc = true;
 
 	spin_lock_bh(&nf_conncount_locks[hash]);
@@ -322,7 +321,7 @@
 		rbconn = rb_entry(*rbnode, struct nf_conncount_rb, node);
 
 		parent = *rbnode;
-		diff = key_diff(key, rbconn->key, keylen);
+		diff = key_diff(key, rbconn->key, data->keylen);
 		if (diff < 0) {
 			rbnode = &((*rbnode)->rb_left);
 		} else if (diff > 0) {
@@ -367,7 +366,9 @@
 
 	conn->tuple = *tuple;
 	conn->zone = *zone;
-	memcpy(rbconn->key, key, sizeof(u32) * keylen);
+	conn->cpu = raw_smp_processor_id();
+	conn->jiffies32 = (u32)jiffies;
+	memcpy(rbconn->key, key, sizeof(u32) * data->keylen);
 
 	nf_conncount_list_init(&rbconn->list);
 	list_add(&conn->node, &rbconn->list.head);
@@ -392,7 +393,6 @@
 	struct rb_node *parent;
 	struct nf_conncount_rb *rbconn;
 	unsigned int hash;
-	u8 keylen = data->keylen;
 
 	hash = jhash2(key, data->keylen, conncount_rnd) % CONNCOUNT_SLOTS;
 	root = &data->root[hash];
@@ -403,7 +403,7 @@
 
 		rbconn = rb_entry(parent, struct nf_conncount_rb, node);
 
-		diff = key_diff(key, rbconn->key, keylen);
+		diff = key_diff(key, rbconn->key, data->keylen);
 		if (diff < 0) {
 			parent = rcu_dereference_raw(parent->rb_left);
 		} else if (diff > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_core.c
@@ -66,6 +66,9 @@
 struct conntrack_gc_work {
 	struct delayed_work	dwork;
 	u32			next_bucket;
+	u32			avg_timeout;
+	u32			count;
+	u32			start_time;
 	bool			exiting;
 	bool			early_drop;
 };
@@ -77,11 +80,24 @@
 /* serialize hash resizes and nf_ct_iterate_cleanup */
 static DEFINE_MUTEX(nf_conntrack_mutex);
 
-#define GC_SCAN_INTERVAL	(120u * HZ)
+#define GC_SCAN_INTERVAL_MAX	(60ul * HZ)
+#define GC_SCAN_INTERVAL_MIN	(1ul * HZ)
+
+/* clamp timeouts to this value (TCP unacked) */
+#define GC_SCAN_INTERVAL_CLAMP	(300ul * HZ)
+
+/* Initial bias pretending we have 100 entries at the upper bound so we don't
+ * wakeup often just because we have three entries with a 1s timeout while still
+ * allowing non-idle machines to wakeup more often when needed.
+ */
+#define GC_SCAN_INITIAL_COUNT	100
+#define GC_SCAN_INTERVAL_INIT	GC_SCAN_INTERVAL_MAX
+
 #define GC_SCAN_MAX_DURATION	msecs_to_jiffies(10)
+#define GC_SCAN_EXPIRED_MAX	(64000u / HZ)
 
-#define MIN_CHAINLEN	8u
-#define MAX_CHAINLEN	(32u - MIN_CHAINLEN)
+#define MIN_CHAINLEN	50u
+#define MAX_CHAINLEN	(80u - MIN_CHAINLEN)
 
 static struct conntrack_gc_work conntrack_gc_work;
 
@@ -558,7 +574,7 @@
 
 #define NFCT_ALIGN(len)	(((len) + NFCT_INFOMASK) & ~NFCT_INFOMASK)
 
-/* Released via destroy_conntrack() */
+/* Released via nf_ct_destroy() */
 struct nf_conn *nf_ct_tmpl_alloc(struct net *net,
 				 const struct nf_conntrack_zone *zone,
 				 gfp_t flags)
@@ -585,7 +601,7 @@
 	tmpl->status = IPS_TEMPLATE;
 	write_pnet(&tmpl->ct_net, net);
 	nf_ct_zone_add(tmpl, zone);
-	atomic_set(&tmpl->ct_general.use, 0);
+	refcount_set(&tmpl->ct_general.use, 1);
 
 	return tmpl;
 }
@@ -612,13 +628,12 @@
 #endif
 }
 
-static void
-destroy_conntrack(struct nf_conntrack *nfct)
+void nf_ct_destroy(struct nf_conntrack *nfct)
 {
 	struct nf_conn *ct = (struct nf_conn *)nfct;
 
-	pr_debug("destroy_conntrack(%p)\n", ct);
-	WARN_ON(atomic_read(&nfct->use) != 0);
+	pr_debug("%s(%p)\n", __func__, ct);
+	WARN_ON(refcount_read(&nfct->use) != 0);
 
 	if (unlikely(nf_ct_is_template(ct))) {
 		nf_ct_tmpl_free(ct);
@@ -643,9 +658,10 @@
 	if (ct->master)
 		nf_ct_put(ct->master);
 
-	pr_debug("destroy_conntrack: returning ct=%p to slab\n", ct);
+	pr_debug("%s: returning ct=%p to slab\n", __func__, ct);
 	nf_conntrack_free(ct);
 }
+EXPORT_SYMBOL(nf_ct_destroy);
 
 static void nf_ct_delete_from_lists(struct nf_conn *ct)
 {
@@ -684,7 +700,7 @@
 
 	tstamp = nf_conn_tstamp_find(ct);
 	if (tstamp) {
-		s32 timeout = ct->timeout - nfct_time_stamp;
+		s32 timeout = READ_ONCE(ct->timeout) - nfct_time_stamp;
 
 		tstamp->stop = ktime_get_real_ns();
 		if (timeout < 0)
@@ -742,7 +758,7 @@
 /* caller must hold rcu readlock and none of the nf_conntrack_locks */
 static void nf_ct_gc_expired(struct nf_conn *ct)
 {
-	if (!atomic_inc_not_zero(&ct->ct_general.use))
+	if (!refcount_inc_not_zero(&ct->ct_general.use))
 		return;
 
 	if (nf_ct_should_gc(ct))
@@ -810,7 +826,7 @@
 		 * in, try to obtain a reference and re-check tuple
 		 */
 		ct = nf_ct_tuplehash_to_ctrack(h);
-		if (likely(atomic_inc_not_zero(&ct->ct_general.use))) {
+		if (likely(refcount_inc_not_zero(&ct->ct_general.use))) {
 			if (likely(nf_ct_key_equal(h, tuple, zone, net)))
 				goto found;
 
@@ -907,7 +923,7 @@
 
 	smp_wmb();
 	/* The caller holds a reference to this object */
-	atomic_set(&ct->ct_general.use, 2);
+	refcount_set(&ct->ct_general.use, 2);
 	__nf_conntrack_hash_insert(ct, hash, reply_hash);
 	nf_conntrack_double_unlock(hash, reply_hash);
 	NF_CT_STAT_INC(net, insert);
@@ -958,7 +974,7 @@
 {
 	struct nf_conn_tstamp *tstamp;
 
-	atomic_inc(&ct->ct_general.use);
+	refcount_inc(&ct->ct_general.use);
 	ct->status |= IPS_CONFIRMED;
 
 	/* set conntrack timestamp, if enabled. */
@@ -989,7 +1005,7 @@
 
 		nf_ct_acct_merge(ct, ctinfo, loser_ct);
 		nf_ct_add_to_dying_list(loser_ct);
-		nf_conntrack_put(&loser_ct->ct_general);
+		nf_ct_put(loser_ct);
 		nf_ct_set(skb, ct, ctinfo);
 
 		NF_CT_STAT_INC(net, clash_resolve);
@@ -1036,7 +1052,7 @@
 	}
 
 	/* We want the clashing entry to go away real soon: 1 second timeout. */
-	loser_ct->timeout = nfct_time_stamp + HZ;
+	WRITE_ONCE(loser_ct->timeout, nfct_time_stamp + HZ);
 
 	/* IPS_NAT_CLASH removes the entry automatically on the first
 	 * reply.  Also prevents UDP tracker from moving the entry to
@@ -1351,7 +1367,7 @@
 		    nf_ct_is_dying(tmp))
 			continue;
 
-		if (!atomic_inc_not_zero(&tmp->ct_general.use))
+		if (!refcount_inc_not_zero(&tmp->ct_general.use))
 			continue;
 
 		/* kill only if still in same netns -- might have moved due to
@@ -1420,16 +1436,31 @@
 
 static void gc_worker(struct work_struct *work)
 {
-	unsigned long end_time = jiffies + GC_SCAN_MAX_DURATION;
 	unsigned int i, hashsz, nf_conntrack_max95 = 0;
-	unsigned long next_run = GC_SCAN_INTERVAL;
+	u32 end_time, start_time = nfct_time_stamp;
 	struct conntrack_gc_work *gc_work;
+	unsigned int expired_count = 0;
+	unsigned long next_run;
+	s32 delta_time;
+	long count;
+
 	gc_work = container_of(work, struct conntrack_gc_work, dwork.work);
 
 	i = gc_work->next_bucket;
 	if (gc_work->early_drop)
 		nf_conntrack_max95 = nf_conntrack_max / 100u * 95u;
 
+	if (i == 0) {
+		gc_work->avg_timeout = GC_SCAN_INTERVAL_INIT;
+		gc_work->count = GC_SCAN_INITIAL_COUNT;
+		gc_work->start_time = start_time;
+	}
+
+	next_run = gc_work->avg_timeout;
+	count = gc_work->count;
+
+	end_time = start_time + GC_SCAN_MAX_DURATION;
+
 	do {
 		struct nf_conntrack_tuple_hash *h;
 		struct hlist_nulls_head *ct_hash;
@@ -1447,6 +1478,7 @@
 		hlist_nulls_for_each_entry_rcu(h, n, &ct_hash[i], hnnode) {
 			struct nf_conntrack_net *cnet;
 			struct net *net;
+			long expires;
 
 			tmp = nf_ct_tuplehash_to_ctrack(h);
 
@@ -1455,11 +1487,30 @@
 				continue;
 			}
 
+			if (expired_count > GC_SCAN_EXPIRED_MAX) {
+				rcu_read_unlock();
+
+				gc_work->next_bucket = i;
+				gc_work->avg_timeout = next_run;
+				gc_work->count = count;
+
+				delta_time = nfct_time_stamp - gc_work->start_time;
+
+				/* re-sched immediately if total cycle time is exceeded */
+				next_run = delta_time < (s32)GC_SCAN_INTERVAL_MAX;
+				goto early_exit;
+			}
+
 			if (nf_ct_is_expired(tmp)) {
 				nf_ct_gc_expired(tmp);
+				expired_count++;
 				continue;
 			}
 
+			expires = clamp(nf_ct_expires(tmp), GC_SCAN_INTERVAL_MIN, GC_SCAN_INTERVAL_CLAMP);
+			expires = (expires - (long)next_run) / ++count;
+			next_run += expires;
+
 			if (nf_conntrack_max95 == 0 || gc_worker_skip_ct(tmp))
 				continue;
 
@@ -1469,7 +1520,7 @@
 				continue;
 
 			/* need to take reference to avoid possible races */
-			if (!atomic_inc_not_zero(&tmp->ct_general.use))
+			if (!refcount_inc_not_zero(&tmp->ct_general.use))
 				continue;
 
 			if (gc_worker_skip_ct(tmp)) {
@@ -1477,8 +1528,10 @@
 				continue;
 			}
 
-			if (gc_worker_can_early_drop(tmp))
+			if (gc_worker_can_early_drop(tmp)) {
 				nf_ct_kill(tmp);
+				expired_count++;
+			}
 
 			nf_ct_put(tmp);
 		}
@@ -1491,33 +1544,39 @@
 		cond_resched();
 		i++;
 
-		if (time_after(jiffies, end_time) && i < hashsz) {
+		delta_time = nfct_time_stamp - end_time;
+		if (delta_time > 0 && i < hashsz) {
+			gc_work->avg_timeout = next_run;
+			gc_work->count = count;
 			gc_work->next_bucket = i;
 			next_run = 0;
-			break;
+			goto early_exit;
 		}
 	} while (i < hashsz);
 
+	gc_work->next_bucket = 0;
+
+	next_run = clamp(next_run, GC_SCAN_INTERVAL_MIN, GC_SCAN_INTERVAL_MAX);
+
+	delta_time = max_t(s32, nfct_time_stamp - gc_work->start_time, 1);
+	if (next_run > (unsigned long)delta_time)
+		next_run -= delta_time;
+	else
+		next_run = 1;
+
+early_exit:
 	if (gc_work->exiting)
 		return;
 
-	/*
-	 * Eviction will normally happen from the packet path, and not
-	 * from this gc worker.
-	 *
-	 * This worker is only here to reap expired entries when system went
-	 * idle after a busy period.
-	 */
-	if (next_run) {
+	if (next_run)
 		gc_work->early_drop = false;
-		gc_work->next_bucket = 0;
-	}
+
 	queue_delayed_work(system_power_efficient_wq, &gc_work->dwork, next_run);
 }
 
 static void conntrack_gc_work_init(struct conntrack_gc_work *gc_work)
 {
-	INIT_DEFERRABLE_WORK(&gc_work->dwork, gc_worker);
+	INIT_DELAYED_WORK(&gc_work->dwork, gc_worker);
 	gc_work->exiting = false;
 }
 
@@ -1560,7 +1619,7 @@
 	/* save hash for reusing when confirming */
 	*(unsigned long *)(&ct->tuplehash[IP_CT_DIR_REPLY].hnnode.pprev) = hash;
 	ct->status = 0;
-	ct->timeout = 0;
+	WRITE_ONCE(ct->timeout, 0);
 	write_pnet(&ct->ct_net, net);
 	memset(&ct->__nfct_init_offset, 0,
 	       offsetof(struct nf_conn, proto) -
@@ -1571,7 +1630,7 @@
 	/* Because we use RCU lookups, we set ct_general.use to zero before
 	 * this is inserted in any list.
 	 */
-	atomic_set(&ct->ct_general.use, 0);
+	refcount_set(&ct->ct_general.use, 0);
 	return ct;
 out:
 	atomic_dec(&cnet->count);
@@ -1596,7 +1655,7 @@
 	/* A freed object has refcnt == 0, that's
 	 * the golden rule for SLAB_TYPESAFE_BY_RCU
 	 */
-	WARN_ON(atomic_read(&ct->ct_general.use) != 0);
+	WARN_ON(refcount_read(&ct->ct_general.use) != 0);
 
 	nf_ct_ext_destroy(ct);
 	kmem_cache_free(nf_conntrack_cachep, ct);
@@ -1661,7 +1720,7 @@
 	cnet = nf_ct_pernet(net);
 	if (cnet->expect_count) {
 		spin_lock(&nf_conntrack_expect_lock);
-		exp = nf_ct_find_expectation(net, zone, tuple);
+		exp = nf_ct_find_expectation(net, zone, tuple, !tmpl || nf_ct_is_confirmed(tmpl));
 		if (exp) {
 			pr_debug("expectation arrives ct=%p exp=%p\n",
 				 ct, exp);
@@ -1676,7 +1735,7 @@
 			}
 
 #ifdef CONFIG_NF_CONNTRACK_MARK
-			ct->mark = exp->master->mark;
+			ct->mark = READ_ONCE(exp->master->mark);
 #endif
 #ifdef CONFIG_NF_CONNTRACK_SECMARK
 			ct->secmark = exp->master->secmark;
@@ -1688,8 +1747,8 @@
 	if (!exp)
 		__nf_ct_try_assign_helper(ct, tmpl, GFP_ATOMIC);
 
-	/* Now it is inserted into the unconfirmed list, bump refcount */
-	nf_conntrack_get(&ct->ct_general);
+	/* Now it is inserted into the unconfirmed list, set refcount to 1. */
+	refcount_set(&ct->ct_general.use, 1);
 	nf_ct_add_to_unconfirmed_list(ct);
 
 	local_bh_enable();
@@ -1920,17 +1979,19 @@
 		/* Invalid: inverse of the return code tells
 		 * the netfilter core what to do */
 		pr_debug("nf_conntrack_in: Can't track with proto module\n");
-		nf_conntrack_put(&ct->ct_general);
+		nf_ct_put(ct);
 		skb->_nfct = 0;
-		NF_CT_STAT_INC_ATOMIC(state->net, invalid);
-		if (ret == -NF_DROP)
-			NF_CT_STAT_INC_ATOMIC(state->net, drop);
 		/* Special case: TCP tracker reports an attempt to reopen a
 		 * closed/aborted connection. We have to go back and create a
 		 * fresh conntrack.
 		 */
 		if (ret == -NF_REPEAT)
 			goto repeat;
+
+		NF_CT_STAT_INC_ATOMIC(state->net, invalid);
+		if (ret == -NF_DROP)
+			NF_CT_STAT_INC_ATOMIC(state->net, drop);
+
 		ret = -ret;
 		goto out;
 	}
@@ -2084,9 +2145,9 @@
 				 struct nf_conn *ct,
 				 enum ip_conntrack_info ctinfo)
 {
+	const struct nf_nat_hook *nat_hook;
 	struct nf_conntrack_tuple_hash *h;
 	struct nf_conntrack_tuple tuple;
-	struct nf_nat_hook *nat_hook;
 	unsigned int status;
 	int dataoff;
 	u16 l3num;
@@ -2163,6 +2224,9 @@
 		return 0;
 
 	helper = rcu_dereference(help->helper);
+	if (!helper)
+		return 0;
+
 	if (!(helper->flags & NF_CT_HELPER_F_USERSPACE))
 		return 0;
 
@@ -2299,7 +2363,7 @@
 
 	return NULL;
 found:
-	atomic_inc(&ct->ct_general.use);
+	refcount_inc(&ct->ct_general.use);
 	spin_unlock(lockp);
 	local_bh_enable();
 	return ct;
@@ -2454,7 +2518,6 @@
 void nf_conntrack_cleanup_start(void)
 {
 	conntrack_gc_work.exiting = true;
-	RCU_INIT_POINTER(ip_ct_attach, NULL);
 }
 
 void nf_conntrack_cleanup_end(void)
@@ -2526,12 +2589,15 @@
 	struct hlist_nulls_head *hash;
 	unsigned int nr_slots, i;
 
-	if (*sizep > (UINT_MAX / sizeof(struct hlist_nulls_head)))
+	if (*sizep > (INT_MAX / sizeof(struct hlist_nulls_head)))
 		return NULL;
 
 	BUILD_BUG_ON(sizeof(struct hlist_nulls_head) != sizeof(struct hlist_head));
 	nr_slots = *sizep = roundup(*sizep, PAGE_SIZE / sizeof(struct hlist_nulls_head));
 
+	if (nr_slots > (INT_MAX / sizeof(struct hlist_nulls_head)))
+		return NULL;
+
 	hash = kvcalloc(nr_slots, sizeof(struct hlist_nulls_head), GFP_KERNEL);
 
 	if (hash && nulls)
@@ -2770,16 +2836,28 @@
 	return ret;
 }
 
-static struct nf_ct_hook nf_conntrack_hook = {
+static void nf_conntrack_set_closing(struct nf_conntrack *nfct)
+{
+	struct nf_conn *ct = nf_ct_to_nf_conn(nfct);
+
+	switch (nf_ct_protonum(ct)) {
+	case IPPROTO_TCP:
+		nf_conntrack_tcp_set_closing(ct);
+		break;
+	}
+}
+
+static const struct nf_ct_hook nf_conntrack_hook = {
 	.update		= nf_conntrack_update,
-	.destroy	= destroy_conntrack,
+	.destroy	= nf_ct_destroy,
 	.get_tuple_skb  = nf_conntrack_get_tuple_skb,
+	.attach		= nf_conntrack_attach,
+	.set_closing	= nf_conntrack_set_closing,
+	.confirm	= __nf_conntrack_confirm,
 };
 
 void nf_conntrack_init_end(void)
 {
-	/* For use by REJECT target */
-	RCU_INIT_POINTER(ip_ct_attach, nf_conntrack_attach);
 	RCU_INIT_POINTER(nf_ct_hook, &nf_conntrack_hook);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_expect.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_expect.c
@@ -171,7 +171,7 @@
 struct nf_conntrack_expect *
 nf_ct_find_expectation(struct net *net,
 		       const struct nf_conntrack_zone *zone,
-		       const struct nf_conntrack_tuple *tuple)
+		       const struct nf_conntrack_tuple *tuple, bool unlink)
 {
 	struct nf_conntrack_net *cnet = nf_ct_pernet(net);
 	struct nf_conntrack_expect *i, *exp = NULL;
@@ -203,15 +203,15 @@
 	 * about to invoke ->destroy(), or nf_ct_delete() via timeout
 	 * or early_drop().
 	 *
-	 * The atomic_inc_not_zero() check tells:  If that fails, we
+	 * The refcount_inc_not_zero() check tells:  If that fails, we
 	 * know that the ct is being destroyed.  If it succeeds, we
 	 * can be sure the ct cannot disappear underneath.
 	 */
 	if (unlikely(nf_ct_is_dying(exp->master) ||
-		     !atomic_inc_not_zero(&exp->master->ct_general.use)))
+		     !refcount_inc_not_zero(&exp->master->ct_general.use)))
 		return NULL;
 
-	if (exp->flags & NF_CT_EXPECT_PERMANENT) {
+	if (exp->flags & NF_CT_EXPECT_PERMANENT || !unlink) {
 		refcount_inc(&exp->use);
 		return exp;
 	} else if (del_timer(&exp->timeout)) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_h323_asn1.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_h323_asn1.c
@@ -533,6 +533,8 @@
 	/* Get fields bitmap */
 	if (nf_h323_error_boundary(bs, 0, f->sz))
 		return H323_ERROR_BOUND;
+	if (f->sz > 32)
+		return H323_ERROR_RANGE;
 	bmp = get_bitmap(bs, f->sz);
 	if (base)
 		*(unsigned int *)base = bmp;
@@ -589,6 +591,8 @@
 	bmp2_len = get_bits(bs, 7) + 1;
 	if (nf_h323_error_boundary(bs, 0, bmp2_len))
 		return H323_ERROR_BOUND;
+	if (bmp2_len > 32)
+		return H323_ERROR_RANGE;
 	bmp2 = get_bitmap(bs, bmp2_len);
 	bmp |= bmp2 >> f->sz;
 	if (base)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_helper.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_helper.c
@@ -405,6 +405,9 @@
 	BUG_ON(me->expect_class_max >= NF_CT_MAX_EXPECT_CLASSES);
 	BUG_ON(strlen(me->name) > NF_CT_HELPER_NAME_LEN - 1);
 
+	if (!nf_ct_helper_hash)
+		return -ENOENT;
+
 	if (me->expect_policy->max_expected > NF_CT_EXPECT_MAX_CNT)
 		return -EINVAL;
 
@@ -556,6 +559,12 @@
 	.id	= NF_CT_EXT_HELPER,
 };
 
+void nf_ct_set_auto_assign_helper_warned(struct net *net)
+{
+	nf_ct_pernet(net)->auto_assign_helper_warned = true;
+}
+EXPORT_SYMBOL_GPL(nf_ct_set_auto_assign_helper_warned);
+
 void nf_conntrack_helper_pernet_init(struct net *net)
 {
 	struct nf_conntrack_net *cnet = nf_ct_pernet(net);
@@ -589,4 +598,5 @@
 {
 	nf_ct_extend_unregister(&helper_extend);
 	kvfree(nf_ct_helper_hash);
+	nf_ct_helper_hash = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_irc.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_irc.c
@@ -151,15 +151,37 @@
 	data = ib_ptr;
 	data_limit = ib_ptr + skb->len - dataoff;
 
-	/* strlen("\1DCC SENT t AAAAAAAA P\1\n")=24
-	 * 5+MINMATCHLEN+strlen("t AAAAAAAA P\1\n")=14 */
-	while (data < data_limit - (19 + MINMATCHLEN)) {
-		if (memcmp(data, "\1DCC ", 5)) {
+	/* Skip any whitespace */
+	while (data < data_limit - 10) {
+		if (*data == ' ' || *data == '\r' || *data == '\n')
+			data++;
+		else
+			break;
+	}
+
+	/* strlen("PRIVMSG x ")=10 */
+	if (data < data_limit - 10) {
+		if (strncasecmp("PRIVMSG ", data, 8))
+			goto out;
+		data += 8;
+	}
+
+	/* strlen(" :\1DCC SENT t AAAAAAAA P\1\n")=26
+	 * 7+MINMATCHLEN+strlen("t AAAAAAAA P\1\n")=26
+	 */
+	while (data < data_limit - (21 + MINMATCHLEN)) {
+		/* Find first " :", the start of message */
+		if (memcmp(data, " :", 2)) {
 			data++;
 			continue;
 		}
+		data += 2;
+
+		/* then check that place only for the DCC command */
+		if (memcmp(data, "\1DCC ", 5))
+			goto out;
 		data += 5;
-		/* we have at least (19+MINMATCHLEN)-5 bytes valid data left */
+		/* we have at least (21+MINMATCHLEN)-(2+5) bytes valid data left */
 
 		iph = ip_hdr(skb);
 		pr_debug("DCC found in master %pI4:%u %pI4:%u\n",
@@ -175,7 +197,7 @@
 			pr_debug("DCC %s detected\n", dccprotos[i]);
 
 			/* we have at least
-			 * (19+MINMATCHLEN)-5-dccprotos[i].matchlen bytes valid
+			 * (21+MINMATCHLEN)-7-dccprotos[i].matchlen bytes valid
 			 * data left (== 14/13 bytes) */
 			if (parse_dcc(data, data_limit, &dcc_ip,
 				       &dcc_port, &addr_beg_p, &addr_end_p)) {
@@ -188,8 +210,9 @@
 
 			/* dcc_ip can be the internal OR external (NAT'ed) IP */
 			tuple = &ct->tuplehash[dir].tuple;
-			if (tuple->src.u3.ip != dcc_ip &&
-			    tuple->dst.u3.ip != dcc_ip) {
+			if ((tuple->src.u3.ip != dcc_ip &&
+			     ct->tuplehash[!dir].tuple.dst.u3.ip != dcc_ip) ||
+			    dcc_port == 0) {
 				net_warn_ratelimited("Forged DCC command from %pI4: %pI4:%u\n",
 						     &tuple->src.u3.ip,
 						     &dcc_ip, dcc_port);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_netlink.c
@@ -322,9 +322,15 @@
 }
 
 #ifdef CONFIG_NF_CONNTRACK_MARK
-static int ctnetlink_dump_mark(struct sk_buff *skb, const struct nf_conn *ct)
+static int ctnetlink_dump_mark(struct sk_buff *skb, const struct nf_conn *ct,
+			       bool dump)
 {
-	if (nla_put_be32(skb, CTA_MARK, htonl(ct->mark)))
+	u32 mark = READ_ONCE(ct->mark);
+
+	if (!mark && !dump)
+		return 0;
+
+	if (nla_put_be32(skb, CTA_MARK, htonl(mark)))
 		goto nla_put_failure;
 	return 0;
 
@@ -332,17 +338,22 @@
 	return -1;
 }
 #else
-#define ctnetlink_dump_mark(a, b) (0)
+#define ctnetlink_dump_mark(a, b, c) (0)
 #endif
 
 #ifdef CONFIG_NF_CONNTRACK_SECMARK
 static int ctnetlink_dump_secctx(struct sk_buff *skb, const struct nf_conn *ct)
 {
 	struct nlattr *nest_secctx;
-	int len, ret;
-	char *secctx;
+	int ret;
+	struct lsmblob blob;
+	struct lsmcontext context;
 
-	ret = security_secid_to_secctx(ct->secmark, &secctx, &len);
+	/* lsmblob_init() puts ct->secmark into all of the secids in blob.
+	 * security_secid_to_secctx() will know which security module
+	 * to use to create the secctx.  */
+	lsmblob_init(&blob, ct->secmark);
+	ret = security_secid_to_secctx(&blob, &context, LSMBLOB_DISPLAY);
 	if (ret)
 		return 0;
 
@@ -351,20 +362,20 @@
 	if (!nest_secctx)
 		goto nla_put_failure;
 
-	if (nla_put_string(skb, CTA_SECCTX_NAME, secctx))
+	if (nla_put_string(skb, CTA_SECCTX_NAME, context.context))
 		goto nla_put_failure;
 	nla_nest_end(skb, nest_secctx);
 
 	ret = 0;
 nla_put_failure:
-	security_release_secctx(secctx, len);
+	security_release_secctx(&context);
 	return ret;
 }
 #else
 #define ctnetlink_dump_secctx(a, b) (0)
 #endif
 
-#ifdef CONFIG_NF_CONNTRACK_LABELS
+#ifdef CONFIG_NF_CONNTRACK_EVENTS
 static inline int ctnetlink_label_size(const struct nf_conn *ct)
 {
 	struct nf_conn_labels *labels = nf_ct_labels_find(ct);
@@ -373,6 +384,7 @@
 		return 0;
 	return nla_total_size(sizeof(labels->bits));
 }
+#endif
 
 static int
 ctnetlink_dump_labels(struct sk_buff *skb, const struct nf_conn *ct)
@@ -393,10 +405,6 @@
 
 	return 0;
 }
-#else
-#define ctnetlink_dump_labels(a, b) (0)
-#define ctnetlink_label_size(a)	(0)
-#endif
 
 #define master_tuple(ct) &(ct->master->tuplehash[IP_CT_DIR_ORIGINAL].tuple)
 
@@ -508,7 +516,7 @@
 
 static int ctnetlink_dump_use(struct sk_buff *skb, const struct nf_conn *ct)
 {
-	if (nla_put_be32(skb, CTA_USE, htonl(atomic_read(&ct->ct_general.use))))
+	if (nla_put_be32(skb, CTA_USE, htonl(refcount_read(&ct->ct_general.use))))
 		goto nla_put_failure;
 	return 0;
 
@@ -537,7 +545,7 @@
 static int ctnetlink_dump_info(struct sk_buff *skb, struct nf_conn *ct)
 {
 	if (ctnetlink_dump_status(skb, ct) < 0 ||
-	    ctnetlink_dump_mark(skb, ct) < 0 ||
+	    ctnetlink_dump_mark(skb, ct, true) < 0 ||
 	    ctnetlink_dump_secctx(skb, ct) < 0 ||
 	    ctnetlink_dump_id(skb, ct) < 0 ||
 	    ctnetlink_dump_use(skb, ct) < 0 ||
@@ -650,11 +658,16 @@
 {
 #ifdef CONFIG_NF_CONNTRACK_SECMARK
 	int len, ret;
+	struct lsmblob blob;
+	struct lsmcontext context;
 
-	ret = security_secid_to_secctx(ct->secmark, NULL, &len);
+	ret = security_secid_to_secctx(&blob, &context, LSMBLOB_DISPLAY);
 	if (ret)
 		return 0;
 
+	len = context.len;
+	security_release_secctx(&context);
+
 	return nla_total_size(0) /* CTA_SECCTX */
 	       + nla_total_size(sizeof(char) * len); /* CTA_SECCTX_NAME */
 #else
@@ -820,8 +833,7 @@
 	}
 
 #ifdef CONFIG_NF_CONNTRACK_MARK
-	if ((events & (1 << IPCT_MARK) || ct->mark)
-	    && ctnetlink_dump_mark(skb, ct) < 0)
+	if (ctnetlink_dump_mark(skb, ct, events & (1 << IPCT_MARK)))
 		goto nla_put_failure;
 #endif
 	nlmsg_end(skb, nlh);
@@ -1011,11 +1023,9 @@
 						   CTA_TUPLE_REPLY,
 						   filter->family,
 						   &filter->zone,
-						   filter->orig_flags);
-		if (err < 0) {
-			err = -EINVAL;
+						   filter->reply_flags);
+		if (err < 0)
 			goto err_filter;
-		}
 	}
 
 	return filter;
@@ -1150,7 +1160,7 @@
 	}
 
 #ifdef CONFIG_NF_CONNTRACK_MARK
-	if ((ct->mark & filter->mark.mask) != filter->mark.val)
+	if ((READ_ONCE(ct->mark) & filter->mark.mask) != filter->mark.val)
 		goto ignore_entry;
 #endif
 	status = (u32)READ_ONCE(ct->status);
@@ -1202,7 +1212,7 @@
 			ct = nf_ct_tuplehash_to_ctrack(h);
 			if (nf_ct_is_expired(ct)) {
 				if (i < ARRAY_SIZE(nf_ct_evict) &&
-				    atomic_inc_not_zero(&ct->ct_general.use))
+				    refcount_inc_not_zero(&ct->ct_general.use))
 					nf_ct_evict[i++] = ct;
 				continue;
 			}
@@ -1543,9 +1553,6 @@
 
 static int ctnetlink_flush_iterate(struct nf_conn *ct, void *data)
 {
-	if (test_bit(IPS_OFFLOAD_BIT, &ct->status))
-		return 0;
-
 	return ctnetlink_filter_match(ct, data);
 }
 
@@ -1609,11 +1616,6 @@
 
 	ct = nf_ct_tuplehash_to_ctrack(h);
 
-	if (test_bit(IPS_OFFLOAD_BIT, &ct->status)) {
-		nf_ct_put(ct);
-		return -EBUSY;
-	}
-
 	if (cda[CTA_ID]) {
 		__be32 id = nla_get_be32(cda[CTA_ID]);
 
@@ -1750,7 +1752,7 @@
 						  NFNL_MSG_TYPE(cb->nlh->nlmsg_type),
 						  ct, dying ? true : false, 0);
 			if (res < 0) {
-				if (!atomic_inc_not_zero(&ct->ct_general.use))
+				if (!refcount_inc_not_zero(&ct->ct_general.use))
 					continue;
 				cb->args[0] = cpu;
 				cb->args[1] = (unsigned long)ct;
@@ -1821,7 +1823,7 @@
 			  const struct nlattr *attr)
 	__must_hold(RCU)
 {
-	struct nf_nat_hook *nat_hook;
+	const struct nf_nat_hook *nat_hook;
 	int err;
 
 	nat_hook = rcu_dereference(nf_nat_hook);
@@ -2000,7 +2002,7 @@
 
 	if (timeout > INT_MAX)
 		timeout = INT_MAX;
-	ct->timeout = nfct_time_stamp + (u32)timeout;
+	WRITE_ONCE(ct->timeout, nfct_time_stamp + (u32)timeout);
 
 	if (test_bit(IPS_DYING_BIT, &ct->status))
 		return -ETIME;
@@ -2018,9 +2020,9 @@
 		mask = ~ntohl(nla_get_be32(cda[CTA_MARK_MASK]));
 
 	mark = ntohl(nla_get_be32(cda[CTA_MARK]));
-	newmark = (ct->mark & mask) ^ mark;
-	if (newmark != ct->mark)
-		ct->mark = newmark;
+	newmark = (READ_ONCE(ct->mark) & mask) ^ mark;
+	if (newmark != READ_ONCE(ct->mark))
+		WRITE_ONCE(ct->mark, newmark);
 }
 #endif
 
@@ -2312,7 +2314,8 @@
 			if (helper->from_nlattr)
 				helper->from_nlattr(helpinfo, ct);
 
-			/* not in hash table yet so not strictly necessary */
+			/* disable helper auto-assignment for this entry */
+			ct->status |= IPS_HELPER;
 			RCU_INIT_POINTER(help->helper, helper);
 		}
 	} else {
@@ -2392,12 +2395,15 @@
 
 	err = nf_conntrack_hash_check_insert(ct);
 	if (err < 0)
-		goto err2;
+		goto err3;
 
 	rcu_read_unlock();
 
 	return ct;
 
+err3:
+	if (ct->master)
+		nf_ct_put(ct->master);
 err2:
 	rcu_read_unlock();
 err1:
@@ -2752,7 +2758,7 @@
 		goto nla_put_failure;
 
 #ifdef CONFIG_NF_CONNTRACK_MARK
-	if (ct->mark && ctnetlink_dump_mark(skb, ct) < 0)
+	if (ctnetlink_dump_mark(skb, ct, true) < 0)
 		goto nla_put_failure;
 #endif
 	if (ctnetlink_dump_labels(skb, ct) < 0)
@@ -2923,7 +2929,7 @@
 	nf_ct_tcp_seqadj_set(skb, ct, ctinfo, diff);
 }
 
-static struct nfnl_ct_hook ctnetlink_glue_hook = {
+static const struct nfnl_ct_hook ctnetlink_glue_hook = {
 	.build_size	= ctnetlink_glue_build_size,
 	.build		= ctnetlink_glue_build,
 	.parse		= ctnetlink_glue_parse,
@@ -2993,7 +2999,9 @@
 	return -1;
 }
 
+#if IS_ENABLED(CONFIG_NF_NAT)
 static const union nf_inet_addr any_addr;
+#endif
 
 static __be32 nf_expect_get_id(const struct nf_conntrack_expect *exp)
 {
@@ -3425,7 +3433,8 @@
 
 		if (cda[CTA_EXPECT_ID]) {
 			__be32 id = nla_get_be32(cda[CTA_EXPECT_ID]);
-			if (ntohl(id) != (u32)(unsigned long)exp) {
+
+			if (id != nf_expect_get_id(exp)) {
 				nf_ct_expect_put(exp);
 				return -ENOENT;
 			}
@@ -3472,10 +3481,12 @@
 	return 0;
 }
 
+#if IS_ENABLED(CONFIG_NF_NAT)
 static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
 	[CTA_EXPECT_NAT_DIR]	= { .type = NLA_U32 },
 	[CTA_EXPECT_NAT_TUPLE]	= { .type = NLA_NESTED },
 };
+#endif
 
 static int
 ctnetlink_parse_expect_nat(const struct nlattr *attr,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_proto_dccp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_proto_dccp.c
@@ -432,9 +432,19 @@
 		       struct sk_buff *skb, unsigned int dataoff,
 		       const struct nf_hook_state *state)
 {
+	static const unsigned long require_seq48 = 1 << DCCP_PKT_REQUEST |
+						   1 << DCCP_PKT_RESPONSE |
+						   1 << DCCP_PKT_CLOSEREQ |
+						   1 << DCCP_PKT_CLOSE |
+						   1 << DCCP_PKT_RESET |
+						   1 << DCCP_PKT_SYNC |
+						   1 << DCCP_PKT_SYNCACK;
 	unsigned int dccp_len = skb->len - dataoff;
 	unsigned int cscov;
 	const char *msg;
+	u8 type;
+
+	BUILD_BUG_ON(DCCP_PKT_INVALID >= BITS_PER_LONG);
 
 	if (dh->dccph_doff * 4 < sizeof(struct dccp_hdr) ||
 	    dh->dccph_doff * 4 > dccp_len) {
@@ -459,34 +469,70 @@
 		goto out_invalid;
 	}
 
-	if (dh->dccph_type >= DCCP_PKT_INVALID) {
+	type = dh->dccph_type;
+	if (type >= DCCP_PKT_INVALID) {
 		msg = "nf_ct_dccp: reserved packet type ";
 		goto out_invalid;
 	}
+
+	if (test_bit(type, &require_seq48) && !dh->dccph_x) {
+		msg = "nf_ct_dccp: type lacks 48bit sequence numbers";
+		goto out_invalid;
+	}
+
 	return false;
 out_invalid:
 	nf_l4proto_log_invalid(skb, state, IPPROTO_DCCP, "%s", msg);
 	return true;
 }
 
+struct nf_conntrack_dccp_buf {
+	struct dccp_hdr dh;	 /* generic header part */
+	struct dccp_hdr_ext ext; /* optional depending dh->dccph_x */
+	union {			 /* depends on header type */
+		struct dccp_hdr_ack_bits ack;
+		struct dccp_hdr_request req;
+		struct dccp_hdr_response response;
+		struct dccp_hdr_reset rst;
+	} u;
+};
+
+static struct dccp_hdr *
+dccp_header_pointer(const struct sk_buff *skb, int offset, const struct dccp_hdr *dh,
+		    struct nf_conntrack_dccp_buf *buf)
+{
+	unsigned int hdrlen = __dccp_hdr_len(dh);
+
+	if (hdrlen > sizeof(*buf))
+		return NULL;
+
+	return skb_header_pointer(skb, offset, hdrlen, buf);
+}
+
 int nf_conntrack_dccp_packet(struct nf_conn *ct, struct sk_buff *skb,
 			     unsigned int dataoff,
 			     enum ip_conntrack_info ctinfo,
 			     const struct nf_hook_state *state)
 {
 	enum ip_conntrack_dir dir = CTINFO2DIR(ctinfo);
-	struct dccp_hdr _dh, *dh;
+	struct nf_conntrack_dccp_buf _dh;
 	u_int8_t type, old_state, new_state;
 	enum ct_dccp_roles role;
 	unsigned int *timeouts;
+	struct dccp_hdr *dh;
 
-	dh = skb_header_pointer(skb, dataoff, sizeof(_dh), &_dh);
+	dh = skb_header_pointer(skb, dataoff, sizeof(*dh), &_dh.dh);
 	if (!dh)
 		return NF_DROP;
 
 	if (dccp_error(dh, skb, dataoff, state))
 		return -NF_ACCEPT;
 
+	/* pull again, including possible 48 bit sequences and subtype header */
+	dh = dccp_header_pointer(skb, dataoff, dh, &_dh);
+	if (!dh)
+		return NF_DROP;
+
 	type = dh->dccph_type;
 	if (!nf_ct_is_confirmed(ct) && !dccp_new(ct, skb, dh, state))
 		return -NF_ACCEPT;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_proto_icmpv6.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_proto_icmpv6.c
@@ -129,6 +129,56 @@
 	nf_l4proto_log_invalid(skb, state, IPPROTO_ICMPV6, "%s", msg);
 }
 
+static noinline_for_stack int
+nf_conntrack_icmpv6_redirect(struct nf_conn *tmpl, struct sk_buff *skb,
+			     unsigned int dataoff,
+			     const struct nf_hook_state *state)
+{
+	u8 hl = ipv6_hdr(skb)->hop_limit;
+	union nf_inet_addr outer_daddr;
+	union {
+		struct nd_opt_hdr nd_opt;
+		struct rd_msg rd_msg;
+	} tmp;
+	const struct nd_opt_hdr *nd_opt;
+	const struct rd_msg *rd_msg;
+
+	rd_msg = skb_header_pointer(skb, dataoff, sizeof(*rd_msg), &tmp.rd_msg);
+	if (!rd_msg) {
+		icmpv6_error_log(skb, state, "short redirect");
+		return -NF_ACCEPT;
+	}
+
+	if (rd_msg->icmph.icmp6_code != 0)
+		return NF_ACCEPT;
+
+	if (hl != 255 || !(ipv6_addr_type(&ipv6_hdr(skb)->saddr) & IPV6_ADDR_LINKLOCAL)) {
+		icmpv6_error_log(skb, state, "invalid saddr or hoplimit for redirect");
+		return -NF_ACCEPT;
+	}
+
+	dataoff += sizeof(*rd_msg);
+
+	/* warning: rd_msg no longer usable after this call */
+	nd_opt = skb_header_pointer(skb, dataoff, sizeof(*nd_opt), &tmp.nd_opt);
+	if (!nd_opt || nd_opt->nd_opt_len == 0) {
+		icmpv6_error_log(skb, state, "redirect without options");
+		return -NF_ACCEPT;
+	}
+
+	/* We could call ndisc_parse_options(), but it would need
+	 * skb_linearize() and a bit more work.
+	 */
+	if (nd_opt->nd_opt_type != ND_OPT_REDIRECT_HDR)
+		return NF_ACCEPT;
+
+	memcpy(&outer_daddr.ip6, &ipv6_hdr(skb)->daddr,
+	       sizeof(outer_daddr.ip6));
+	dataoff += 8;
+	return nf_conntrack_inet_error(tmpl, skb, dataoff, state,
+				       IPPROTO_ICMPV6, &outer_daddr);
+}
+
 int nf_conntrack_icmpv6_error(struct nf_conn *tmpl,
 			      struct sk_buff *skb,
 			      unsigned int dataoff,
@@ -159,6 +209,9 @@
 		return NF_ACCEPT;
 	}
 
+	if (icmp6h->icmp6_type == NDISC_REDIRECT)
+		return nf_conntrack_icmpv6_redirect(tmpl, skb, dataoff, state);
+
 	/* is not error message ? */
 	if (icmp6h->icmp6_type >= 128)
 		return NF_ACCEPT;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_proto_sctp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_proto_sctp.c
@@ -27,22 +27,16 @@
 #include <net/netfilter/nf_conntrack_ecache.h>
 #include <net/netfilter/nf_conntrack_timeout.h>
 
-/* FIXME: Examine ipfilter's timeouts and conntrack transitions more
-   closely.  They're more complex. --RR
-
-   And so for me for SCTP :D -Kiran */
-
 static const char *const sctp_conntrack_names[] = {
-	"NONE",
-	"CLOSED",
-	"COOKIE_WAIT",
-	"COOKIE_ECHOED",
-	"ESTABLISHED",
-	"SHUTDOWN_SENT",
-	"SHUTDOWN_RECD",
-	"SHUTDOWN_ACK_SENT",
-	"HEARTBEAT_SENT",
-	"HEARTBEAT_ACKED",
+	[SCTP_CONNTRACK_NONE]			= "NONE",
+	[SCTP_CONNTRACK_CLOSED]			= "CLOSED",
+	[SCTP_CONNTRACK_COOKIE_WAIT]		= "COOKIE_WAIT",
+	[SCTP_CONNTRACK_COOKIE_ECHOED]		= "COOKIE_ECHOED",
+	[SCTP_CONNTRACK_ESTABLISHED]		= "ESTABLISHED",
+	[SCTP_CONNTRACK_SHUTDOWN_SENT]		= "SHUTDOWN_SENT",
+	[SCTP_CONNTRACK_SHUTDOWN_RECD]		= "SHUTDOWN_RECD",
+	[SCTP_CONNTRACK_SHUTDOWN_ACK_SENT]	= "SHUTDOWN_ACK_SENT",
+	[SCTP_CONNTRACK_HEARTBEAT_SENT]		= "HEARTBEAT_SENT",
 };
 
 #define SECS  * HZ
@@ -54,12 +48,11 @@
 	[SCTP_CONNTRACK_CLOSED]			= 10 SECS,
 	[SCTP_CONNTRACK_COOKIE_WAIT]		= 3 SECS,
 	[SCTP_CONNTRACK_COOKIE_ECHOED]		= 3 SECS,
-	[SCTP_CONNTRACK_ESTABLISHED]		= 5 DAYS,
-	[SCTP_CONNTRACK_SHUTDOWN_SENT]		= 300 SECS / 1000,
-	[SCTP_CONNTRACK_SHUTDOWN_RECD]		= 300 SECS / 1000,
+	[SCTP_CONNTRACK_ESTABLISHED]		= 210 SECS,
+	[SCTP_CONNTRACK_SHUTDOWN_SENT]		= 3 SECS,
+	[SCTP_CONNTRACK_SHUTDOWN_RECD]		= 3 SECS,
 	[SCTP_CONNTRACK_SHUTDOWN_ACK_SENT]	= 3 SECS,
 	[SCTP_CONNTRACK_HEARTBEAT_SENT]		= 30 SECS,
-	[SCTP_CONNTRACK_HEARTBEAT_ACKED]	= 210 SECS,
 };
 
 #define	SCTP_FLAG_HEARTBEAT_VTAG_FAILED	1
@@ -73,7 +66,6 @@
 #define	sSR SCTP_CONNTRACK_SHUTDOWN_RECD
 #define	sSA SCTP_CONNTRACK_SHUTDOWN_ACK_SENT
 #define	sHS SCTP_CONNTRACK_HEARTBEAT_SENT
-#define	sHA SCTP_CONNTRACK_HEARTBEAT_ACKED
 #define	sIV SCTP_CONNTRACK_MAX
 
 /*
@@ -96,9 +88,6 @@
 CLOSED            - We have seen a SHUTDOWN_COMPLETE chunk in the direction of
 		    the SHUTDOWN chunk. Connection is closed.
 HEARTBEAT_SENT    - We have seen a HEARTBEAT in a new flow.
-HEARTBEAT_ACKED   - We have seen a HEARTBEAT-ACK in the direction opposite to
-		    that of the HEARTBEAT chunk. Secondary connection is
-		    established.
 */
 
 /* TODO
@@ -115,33 +104,33 @@
 static const u8 sctp_conntracks[2][11][SCTP_CONNTRACK_MAX] = {
 	{
 /*	ORIGINAL	*/
-/*                  sNO, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS, sHA */
-/* init         */ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sCW, sHA},
-/* init_ack     */ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sCL, sHA},
-/* abort        */ {sCL, sCL, sCL, sCL, sCL, sCL, sCL, sCL, sCL, sCL},
-/* shutdown     */ {sCL, sCL, sCW, sCE, sSS, sSS, sSR, sSA, sCL, sSS},
-/* shutdown_ack */ {sSA, sCL, sCW, sCE, sES, sSA, sSA, sSA, sSA, sHA},
-/* error        */ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sCL, sHA},/* Can't have Stale cookie*/
-/* cookie_echo  */ {sCL, sCL, sCE, sCE, sES, sSS, sSR, sSA, sCL, sHA},/* 5.2.4 - Big TODO */
-/* cookie_ack   */ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sCL, sHA},/* Can't come in orig dir */
-/* shutdown_comp*/ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sCL, sCL, sHA},
-/* heartbeat    */ {sHS, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS, sHA},
-/* heartbeat_ack*/ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS, sHA}
+/*                  sNO, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS */
+/* init         */ {sCL, sCL, sCW, sCE, sES, sCL, sCL, sSA, sCW},
+/* init_ack     */ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sCL},
+/* abort        */ {sCL, sCL, sCL, sCL, sCL, sCL, sCL, sCL, sCL},
+/* shutdown     */ {sCL, sCL, sCW, sCE, sSS, sSS, sSR, sSA, sCL},
+/* shutdown_ack */ {sSA, sCL, sCW, sCE, sES, sSA, sSA, sSA, sSA},
+/* error        */ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sCL},/* Can't have Stale cookie*/
+/* cookie_echo  */ {sCL, sCL, sCE, sCE, sES, sSS, sSR, sSA, sCL},/* 5.2.4 - Big TODO */
+/* cookie_ack   */ {sCL, sCL, sCW, sES, sES, sSS, sSR, sSA, sCL},/* Can't come in orig dir */
+/* shutdown_comp*/ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sCL, sCL},
+/* heartbeat    */ {sHS, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS},
+/* heartbeat_ack*/ {sCL, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS},
 	},
 	{
 /*	REPLY	*/
-/*                  sNO, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS, sHA */
-/* init         */ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sIV, sHA},/* INIT in sCL Big TODO */
-/* init_ack     */ {sIV, sCW, sCW, sCE, sES, sSS, sSR, sSA, sIV, sHA},
-/* abort        */ {sIV, sCL, sCL, sCL, sCL, sCL, sCL, sCL, sIV, sCL},
-/* shutdown     */ {sIV, sCL, sCW, sCE, sSR, sSS, sSR, sSA, sIV, sSR},
-/* shutdown_ack */ {sIV, sCL, sCW, sCE, sES, sSA, sSA, sSA, sIV, sHA},
-/* error        */ {sIV, sCL, sCW, sCL, sES, sSS, sSR, sSA, sIV, sHA},
-/* cookie_echo  */ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sIV, sHA},/* Can't come in reply dir */
-/* cookie_ack   */ {sIV, sCL, sCW, sES, sES, sSS, sSR, sSA, sIV, sHA},
-/* shutdown_comp*/ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sCL, sIV, sHA},
-/* heartbeat    */ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS, sHA},
-/* heartbeat_ack*/ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHA, sHA}
+/*                  sNO, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS */
+/* init         */ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sIV},/* INIT in sCL Big TODO */
+/* init_ack     */ {sIV, sCW, sCW, sCE, sES, sSS, sSR, sSA, sIV},
+/* abort        */ {sIV, sCL, sCL, sCL, sCL, sCL, sCL, sCL, sIV},
+/* shutdown     */ {sIV, sCL, sCW, sCE, sSR, sSS, sSR, sSA, sIV},
+/* shutdown_ack */ {sIV, sCL, sCW, sCE, sES, sSA, sSA, sSA, sIV},
+/* error        */ {sIV, sCL, sCW, sCL, sES, sSS, sSR, sSA, sIV},
+/* cookie_echo  */ {sIV, sCL, sCE, sCE, sES, sSS, sSR, sSA, sIV},/* Can't come in reply dir */
+/* cookie_ack   */ {sIV, sCL, sCW, sES, sES, sSS, sSR, sSA, sIV},
+/* shutdown_comp*/ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sCL, sIV},
+/* heartbeat    */ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sHS},
+/* heartbeat_ack*/ {sIV, sCL, sCW, sCE, sES, sSS, sSR, sSA, sES},
 	}
 };
 
@@ -310,7 +299,7 @@
 			pr_debug("Setting vtag %x for secondary conntrack\n",
 				 sh->vtag);
 			ct->proto.sctp.vtag[IP_CT_DIR_ORIGINAL] = sh->vtag;
-		} else {
+		} else if (sch->type == SCTP_CID_SHUTDOWN_ACK) {
 		/* If it is a shutdown ack OOTB packet, we expect a return
 		   shutdown complete, otherwise an ABORT Sec 8.4 (5) and (8) */
 			pr_debug("Setting vtag %x for new conn OOTB\n",
@@ -412,24 +401,34 @@
 	for_each_sctp_chunk (skb, sch, _sch, offset, dataoff, count) {
 		/* Special cases of Verification tag check (Sec 8.5.1) */
 		if (sch->type == SCTP_CID_INIT) {
-			/* Sec 8.5.1 (A) */
+			/* (A) vtag MUST be zero */
 			if (sh->vtag != 0)
 				goto out_unlock;
 		} else if (sch->type == SCTP_CID_ABORT) {
-			/* Sec 8.5.1 (B) */
-			if (sh->vtag != ct->proto.sctp.vtag[dir] &&
-			    sh->vtag != ct->proto.sctp.vtag[!dir])
+			/* (B) vtag MUST match own vtag if T flag is unset OR
+			 * MUST match peer's vtag if T flag is set
+			 */
+			if ((!(sch->flags & SCTP_CHUNK_FLAG_T) &&
+			     sh->vtag != ct->proto.sctp.vtag[dir]) ||
+			    ((sch->flags & SCTP_CHUNK_FLAG_T) &&
+			     sh->vtag != ct->proto.sctp.vtag[!dir]))
 				goto out_unlock;
 		} else if (sch->type == SCTP_CID_SHUTDOWN_COMPLETE) {
-			/* Sec 8.5.1 (C) */
-			if (sh->vtag != ct->proto.sctp.vtag[dir] &&
-			    sh->vtag != ct->proto.sctp.vtag[!dir] &&
-			    sch->flags & SCTP_CHUNK_FLAG_T)
+			/* (C) vtag MUST match own vtag if T flag is unset OR
+			 * MUST match peer's vtag if T flag is set
+			 */
+			if ((!(sch->flags & SCTP_CHUNK_FLAG_T) &&
+			     sh->vtag != ct->proto.sctp.vtag[dir]) ||
+			    ((sch->flags & SCTP_CHUNK_FLAG_T) &&
+			     sh->vtag != ct->proto.sctp.vtag[!dir]))
 				goto out_unlock;
 		} else if (sch->type == SCTP_CID_COOKIE_ECHO) {
-			/* Sec 8.5.1 (D) */
+			/* (D) vtag must be same as init_vtag as found in INIT_ACK */
 			if (sh->vtag != ct->proto.sctp.vtag[dir])
 				goto out_unlock;
+		} else if (sch->type == SCTP_CID_COOKIE_ACK) {
+			ct->proto.sctp.init[dir] = 0;
+			ct->proto.sctp.init[!dir] = 0;
 		} else if (sch->type == SCTP_CID_HEARTBEAT) {
 			if (ct->proto.sctp.vtag[dir] == 0) {
 				pr_debug("Setting %d vtag %x for dir %d\n", sch->type, sh->vtag, dir);
@@ -478,22 +477,55 @@
 		}
 
 		/* If it is an INIT or an INIT ACK note down the vtag */
-		if (sch->type == SCTP_CID_INIT ||
-		    sch->type == SCTP_CID_INIT_ACK) {
-			struct sctp_inithdr _inithdr, *ih;
+		if (sch->type == SCTP_CID_INIT) {
+			struct sctp_inithdr _ih, *ih;
 
-			ih = skb_header_pointer(skb, offset + sizeof(_sch),
-						sizeof(_inithdr), &_inithdr);
-			if (ih == NULL)
+			ih = skb_header_pointer(skb, offset + sizeof(_sch), sizeof(*ih), &_ih);
+			if (!ih)
+				goto out_unlock;
+
+			if (ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir])
+				ct->proto.sctp.init[!dir] = 0;
+			ct->proto.sctp.init[dir] = 1;
+
+			pr_debug("Setting vtag %x for dir %d\n", ih->init_tag, !dir);
+			ct->proto.sctp.vtag[!dir] = ih->init_tag;
+
+			/* don't renew timeout on init retransmit so
+			 * port reuse by client or NAT middlebox cannot
+			 * keep entry alive indefinitely (incl. nat info).
+			 */
+			if (new_state == SCTP_CONNTRACK_CLOSED &&
+			    old_state == SCTP_CONNTRACK_CLOSED &&
+			    nf_ct_is_confirmed(ct))
+				ignore = true;
+		} else if (sch->type == SCTP_CID_INIT_ACK) {
+			struct sctp_inithdr _ih, *ih;
+			__be32 vtag;
+
+			ih = skb_header_pointer(skb, offset + sizeof(_sch), sizeof(*ih), &_ih);
+			if (!ih)
+				goto out_unlock;
+
+			vtag = ct->proto.sctp.vtag[!dir];
+			if (!ct->proto.sctp.init[!dir] && vtag && vtag != ih->init_tag)
+				goto out_unlock;
+			/* collision */
+			if (ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
+			    vtag != ih->init_tag)
 				goto out_unlock;
-			pr_debug("Setting vtag %x for dir %d\n",
-				 ih->init_tag, !dir);
+
+			pr_debug("Setting vtag %x for dir %d\n", ih->init_tag, !dir);
 			ct->proto.sctp.vtag[!dir] = ih->init_tag;
 		}
 
 		ct->proto.sctp.state = new_state;
-		if (old_state != new_state)
+		if (old_state != new_state) {
 			nf_conntrack_event_cache(IPCT_PROTOINFO, ct);
+			if (new_state == SCTP_CONNTRACK_ESTABLISHED &&
+			    !test_and_set_bit(IPS_ASSURED_BIT, &ct->status))
+				nf_conntrack_event_cache(IPCT_ASSURED, ct);
+		}
 	}
 	spin_unlock_bh(&ct->lock);
 
@@ -507,14 +539,6 @@
 
 	nf_ct_refresh_acct(ct, ctinfo, skb, timeouts[new_state]);
 
-	if (old_state == SCTP_CONNTRACK_COOKIE_ECHOED &&
-	    dir == IP_CT_DIR_REPLY &&
-	    new_state == SCTP_CONNTRACK_ESTABLISHED) {
-		pr_debug("Setting assured bit\n");
-		set_bit(IPS_ASSURED_BIT, &ct->status);
-		nf_conntrack_event_cache(IPCT_ASSURED, ct);
-	}
-
 	return NF_ACCEPT;
 
 out_unlock:
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_proto_tcp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_proto_tcp.c
@@ -341,8 +341,8 @@
 	if (!ptr)
 		return;
 
-	state->td_scale =
-	state->flags = 0;
+	state->td_scale = 0;
+	state->flags &= IP_CT_TCP_FLAG_BE_LIBERAL;
 
 	while (length > 0) {
 		int opcode=*ptr++;
@@ -671,6 +671,37 @@
 		    tn->tcp_be_liberal)
 			res = true;
 		if (!res) {
+			bool seq_ok = before(seq, sender->td_maxend + 1);
+
+			if (!seq_ok) {
+				u32 overshot = end - sender->td_maxend + 1;
+				bool ack_ok;
+
+				ack_ok = after(sack, receiver->td_end - MAXACKWINDOW(sender) - 1);
+
+				if (in_recv_win &&
+				    ack_ok &&
+				    overshot <= receiver->td_maxwin &&
+				    before(sack, receiver->td_end + 1)) {
+					/* Work around TCPs that send more bytes than allowed by
+					 * the receive window.
+					 *
+					 * If the (marked as invalid) packet is allowed to pass by
+					 * the ruleset and the peer acks this data, then its possible
+					 * all future packets will trigger 'ACK is over upper bound' check.
+					 *
+					 * Thus if only the sequence check fails then do update td_end so
+					 * possible ACK for this data can update internal state.
+					 */
+					sender->td_end = end;
+					sender->flags |= IP_CT_TCP_FLAG_DATA_UNACKNOWLEDGED;
+
+					nf_ct_l4proto_log_invalid(skb, ct, hook_state,
+								  "%u bytes more than expected", overshot);
+					return res;
+				}
+			}
+
 			nf_ct_l4proto_log_invalid(skb, ct, hook_state,
 			"%s",
 			before(seq, sender->td_maxend + 1) ?
@@ -839,6 +870,51 @@
 	return false;
 }
 
+void nf_conntrack_tcp_set_closing(struct nf_conn *ct)
+{
+	enum tcp_conntrack old_state;
+	const unsigned int *timeouts;
+	u32 timeout;
+
+	if (!nf_ct_is_confirmed(ct))
+		return;
+
+	spin_lock_bh(&ct->lock);
+	old_state = ct->proto.tcp.state;
+	ct->proto.tcp.state = TCP_CONNTRACK_CLOSE;
+
+	if (old_state == TCP_CONNTRACK_CLOSE ||
+	    test_bit(IPS_FIXED_TIMEOUT_BIT, &ct->status)) {
+		spin_unlock_bh(&ct->lock);
+		return;
+	}
+
+	timeouts = nf_ct_timeout_lookup(ct);
+	if (!timeouts) {
+		const struct nf_tcp_net *tn;
+
+		tn = nf_tcp_pernet(nf_ct_net(ct));
+		timeouts = tn->timeouts;
+	}
+
+	timeout = timeouts[TCP_CONNTRACK_CLOSE];
+	WRITE_ONCE(ct->timeout, timeout + nfct_time_stamp);
+
+	spin_unlock_bh(&ct->lock);
+
+	nf_conntrack_event_cache(IPCT_PROTOINFO, ct);
+}
+
+static void nf_ct_tcp_state_reset(struct ip_ct_tcp_state *state)
+{
+	state->td_end		= 0;
+	state->td_maxend	= 0;
+	state->td_maxwin	= 0;
+	state->td_maxack	= 0;
+	state->td_scale		= 0;
+	state->flags		&= IP_CT_TCP_FLAG_BE_LIBERAL;
+}
+
 /* Returns verdict for packet, or -1 for invalid. */
 int nf_conntrack_tcp_packet(struct nf_conn *ct,
 			    struct sk_buff *skb,
@@ -945,8 +1021,7 @@
 			ct->proto.tcp.last_flags &= ~IP_CT_EXP_CHALLENGE_ACK;
 			ct->proto.tcp.seen[ct->proto.tcp.last_dir].flags =
 				ct->proto.tcp.last_flags;
-			memset(&ct->proto.tcp.seen[dir], 0,
-			       sizeof(struct ip_ct_tcp_state));
+			nf_ct_tcp_state_reset(&ct->proto.tcp.seen[dir]);
 			break;
 		}
 		ct->proto.tcp.last_index = index;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_proto_udp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_proto_udp.c
@@ -104,10 +104,13 @@
 	 */
 	if (test_bit(IPS_SEEN_REPLY_BIT, &ct->status)) {
 		unsigned long extra = timeouts[UDP_CT_UNREPLIED];
+		bool stream = false;
 
 		/* Still active after two seconds? Extend timeout. */
-		if (time_after(jiffies, ct->proto.udp.stream_ts))
+		if (time_after(jiffies, ct->proto.udp.stream_ts)) {
 			extra = timeouts[UDP_CT_REPLIED];
+			stream = true;
+		}
 
 		nf_ct_refresh_acct(ct, ctinfo, skb, extra);
 
@@ -116,7 +119,7 @@
 			return NF_ACCEPT;
 
 		/* Also, more likely to be important, and not a probe */
-		if (!test_and_set_bit(IPS_ASSURED_BIT, &ct->status))
+		if (stream && !test_and_set_bit(IPS_ASSURED_BIT, &ct->status))
 			nf_conntrack_event_cache(IPCT_ASSURED, ct);
 	} else {
 		nf_ct_refresh_acct(ct, ctinfo, skb, timeouts[UDP_CT_UNREPLIED]);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_sip.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_sip.c
@@ -477,7 +477,7 @@
 				return ret;
 			if (ret == 0)
 				break;
-			dataoff += *matchoff;
+			dataoff = *matchoff;
 		}
 		*in_header = 0;
 	}
@@ -489,7 +489,7 @@
 			break;
 		if (ret == 0)
 			return ret;
-		dataoff += *matchoff;
+		dataoff = *matchoff;
 	}
 
 	if (in_header)
@@ -611,7 +611,7 @@
 	start += strlen(name);
 	*val = simple_strtoul(start, &end, 0);
 	if (start == end)
-		return 0;
+		return -1;
 	if (matchoff && matchlen) {
 		*matchoff = start - dptr;
 		*matchlen = end - start;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_conntrack_standalone.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_conntrack_standalone.c
@@ -176,16 +176,17 @@
 static void ct_show_secctx(struct seq_file *s, const struct nf_conn *ct)
 {
 	int ret;
-	u32 len;
-	char *secctx;
+	struct lsmblob blob;
+	struct lsmcontext context;
 
-	ret = security_secid_to_secctx(ct->secmark, &secctx, &len);
+	lsmblob_init(&blob, ct->secmark);
+	ret = security_secid_to_secctx(&blob, &context, LSMBLOB_DISPLAY);
 	if (ret)
 		return;
 
-	seq_printf(s, "secctx=%s ", secctx);
+	seq_printf(s, "secctx=%s ", context.context);
 
-	security_release_secctx(secctx, len);
+	security_release_secctx(&context);
 }
 #else
 static inline void ct_show_secctx(struct seq_file *s, const struct nf_conn *ct)
@@ -303,7 +304,7 @@
 	int ret = 0;
 
 	WARN_ON(!ct);
-	if (unlikely(!atomic_inc_not_zero(&ct->ct_general.use)))
+	if (unlikely(!refcount_inc_not_zero(&ct->ct_general.use)))
 		return 0;
 
 	if (nf_ct_should_gc(ct)) {
@@ -363,14 +364,14 @@
 		goto release;
 
 #if defined(CONFIG_NF_CONNTRACK_MARK)
-	seq_printf(s, "mark=%u ", ct->mark);
+	seq_printf(s, "mark=%u ", READ_ONCE(ct->mark));
 #endif
 
 	ct_show_secctx(s, ct);
 	ct_show_zone(s, ct, NF_CT_DEFAULT_ZONE_DIR);
 	ct_show_delta_time(s, ct);
 
-	seq_printf(s, "use=%u\n", atomic_read(&ct->ct_general.use));
+	seq_printf(s, "use=%u\n", refcount_read(&ct->ct_general.use));
 
 	if (seq_has_overflowed(s))
 		goto release;
@@ -599,7 +600,6 @@
 	NF_SYSCTL_CT_PROTO_TIMEOUT_SCTP_SHUTDOWN_RECD,
 	NF_SYSCTL_CT_PROTO_TIMEOUT_SCTP_SHUTDOWN_ACK_SENT,
 	NF_SYSCTL_CT_PROTO_TIMEOUT_SCTP_HEARTBEAT_SENT,
-	NF_SYSCTL_CT_PROTO_TIMEOUT_SCTP_HEARTBEAT_ACKED,
 #endif
 #ifdef CONFIG_NF_CT_PROTO_DCCP
 	NF_SYSCTL_CT_PROTO_TIMEOUT_DCCP_REQUEST,
@@ -823,7 +823,7 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_jiffies,
 	},
-#if IS_ENABLED(CONFIG_NFT_FLOW_OFFLOAD)
+#if IS_ENABLED(CONFIG_NF_FLOW_TABLE)
 	[NF_SYSCTL_CT_PROTO_TIMEOUT_UDP_OFFLOAD] = {
 		.procname	= "nf_flowtable_udp_timeout",
 		.maxlen		= sizeof(unsigned int),
@@ -892,12 +892,6 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_jiffies,
 	},
-	[NF_SYSCTL_CT_PROTO_TIMEOUT_SCTP_HEARTBEAT_ACKED] = {
-		.procname       = "nf_conntrack_sctp_timeout_heartbeat_acked",
-		.maxlen         = sizeof(unsigned int),
-		.mode           = 0644,
-		.proc_handler   = proc_dointvec_jiffies,
-	},
 #endif
 #ifdef CONFIG_NF_CT_PROTO_DCCP
 	[NF_SYSCTL_CT_PROTO_TIMEOUT_DCCP_REQUEST] = {
@@ -1041,7 +1035,6 @@
 	XASSIGN(SHUTDOWN_RECD, sn);
 	XASSIGN(SHUTDOWN_ACK_SENT, sn);
 	XASSIGN(HEARTBEAT_SENT, sn);
-	XASSIGN(HEARTBEAT_ACKED, sn);
 #undef XASSIGN
 #endif
 }
@@ -1237,11 +1230,12 @@
 	nf_conntrack_htable_size_user = nf_conntrack_htable_size;
 #endif
 
+	nf_conntrack_init_end();
+
 	ret = register_pernet_subsys(&nf_conntrack_net_ops);
 	if (ret < 0)
 		goto out_pernet;
 
-	nf_conntrack_init_end();
 	return 0;
 
 out_pernet:
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_flow_table_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_flow_table_core.c
@@ -48,7 +48,7 @@
 	struct flow_offload *flow;
 
 	if (unlikely(nf_ct_is_dying(ct) ||
-	    !atomic_inc_not_zero(&ct->ct_general.use)))
+	    !refcount_inc_not_zero(&ct->ct_general.use)))
 		return NULL;
 
 	flow = kzalloc(sizeof(*flow), GFP_ATOMIC);
@@ -86,12 +86,22 @@
 	return 0;
 }
 
+static struct dst_entry *nft_route_dst_fetch(struct nf_flow_route *route,
+					     enum flow_offload_tuple_dir dir)
+{
+	struct dst_entry *dst = route->tuple[dir].dst;
+
+	route->tuple[dir].dst = NULL;
+
+	return dst;
+}
+
 static int flow_offload_fill_route(struct flow_offload *flow,
-				   const struct nf_flow_route *route,
+				   struct nf_flow_route *route,
 				   enum flow_offload_tuple_dir dir)
 {
 	struct flow_offload_tuple *flow_tuple = &flow->tuplehash[dir].tuple;
-	struct dst_entry *dst = route->tuple[dir].dst;
+	struct dst_entry *dst = nft_route_dst_fetch(route, dir);
 	int i, j = 0;
 
 	switch (flow_tuple->l3proto) {
@@ -121,12 +131,10 @@
 		       ETH_ALEN);
 		flow_tuple->out.ifidx = route->tuple[dir].out.ifindex;
 		flow_tuple->out.hw_ifidx = route->tuple[dir].out.hw_ifindex;
+		dst_release(dst);
 		break;
 	case FLOW_OFFLOAD_XMIT_XFRM:
 	case FLOW_OFFLOAD_XMIT_NEIGH:
-		if (!dst_hold_safe(route->tuple[dir].dst))
-			return -1;
-
 		flow_tuple->dst_cache = dst;
 		flow_tuple->dst_cookie = flow_offload_dst_cookie(flow_tuple);
 		break;
@@ -147,38 +155,22 @@
 		dst_release(flow->tuplehash[dir].tuple.dst_cache);
 }
 
-int flow_offload_route_init(struct flow_offload *flow,
-			    const struct nf_flow_route *route)
+void flow_offload_route_init(struct flow_offload *flow,
+			     struct nf_flow_route *route)
 {
-	int err;
-
-	err = flow_offload_fill_route(flow, route, FLOW_OFFLOAD_DIR_ORIGINAL);
-	if (err < 0)
-		return err;
-
-	err = flow_offload_fill_route(flow, route, FLOW_OFFLOAD_DIR_REPLY);
-	if (err < 0)
-		goto err_route_reply;
-
+	flow_offload_fill_route(flow, route, FLOW_OFFLOAD_DIR_ORIGINAL);
+	flow_offload_fill_route(flow, route, FLOW_OFFLOAD_DIR_REPLY);
 	flow->type = NF_FLOW_OFFLOAD_ROUTE;
-
-	return 0;
-
-err_route_reply:
-	nft_flow_dst_release(flow, FLOW_OFFLOAD_DIR_ORIGINAL);
-
-	return err;
 }
 EXPORT_SYMBOL_GPL(flow_offload_route_init);
 
 static void flow_offload_fixup_tcp(struct ip_ct_tcp *tcp)
 {
-	tcp->state = TCP_CONNTRACK_ESTABLISHED;
 	tcp->seen[0].td_maxwin = 0;
 	tcp->seen[1].td_maxwin = 0;
 }
 
-static void flow_offload_fixup_ct_timeout(struct nf_conn *ct)
+static void flow_offload_fixup_ct(struct nf_conn *ct)
 {
 	struct net *net = nf_ct_net(ct);
 	int l4num = nf_ct_protonum(ct);
@@ -187,7 +179,9 @@
 	if (l4num == IPPROTO_TCP) {
 		struct nf_tcp_net *tn = nf_tcp_pernet(net);
 
-		timeout = tn->timeouts[TCP_CONNTRACK_ESTABLISHED];
+		flow_offload_fixup_tcp(&ct->proto.tcp);
+
+		timeout = tn->timeouts[ct->proto.tcp.state];
 		timeout -= tn->offload_timeout;
 	} else if (l4num == IPPROTO_UDP) {
 		struct nf_udp_net *tn = nf_udp_pernet(net);
@@ -201,20 +195,8 @@
 	if (timeout < 0)
 		timeout = 0;
 
-	if (nf_flow_timeout_delta(ct->timeout) > (__s32)timeout)
-		ct->timeout = nfct_time_stamp + timeout;
-}
-
-static void flow_offload_fixup_ct_state(struct nf_conn *ct)
-{
-	if (nf_ct_protonum(ct) == IPPROTO_TCP)
-		flow_offload_fixup_tcp(&ct->proto.tcp);
-}
-
-static void flow_offload_fixup_ct(struct nf_conn *ct)
-{
-	flow_offload_fixup_ct_state(ct);
-	flow_offload_fixup_ct_timeout(ct);
+	if (nf_flow_timeout_delta(READ_ONCE(ct->timeout)) > (__s32)timeout)
+		WRITE_ONCE(ct->timeout, nfct_time_stamp + timeout);
 }
 
 static void flow_offload_route_release(struct flow_offload *flow)
@@ -329,8 +311,10 @@
 	u32 timeout;
 
 	timeout = nf_flowtable_time_stamp + flow_offload_get_timeout(flow);
-	if (READ_ONCE(flow->timeout) != timeout)
+	if (timeout - READ_ONCE(flow->timeout) > HZ)
 		WRITE_ONCE(flow->timeout, timeout);
+	else
+		return;
 
 	if (likely(!nf_flowtable_hw_offload(flow_table)))
 		return;
@@ -353,22 +337,14 @@
 	rhashtable_remove_fast(&flow_table->rhashtable,
 			       &flow->tuplehash[FLOW_OFFLOAD_DIR_REPLY].node,
 			       nf_flow_offload_rhash_params);
-
-	clear_bit(IPS_OFFLOAD_BIT, &flow->ct->status);
-
-	if (nf_flow_has_expired(flow))
-		flow_offload_fixup_ct(flow->ct);
-	else
-		flow_offload_fixup_ct_timeout(flow->ct);
-
 	flow_offload_free(flow);
 }
 
 void flow_offload_teardown(struct flow_offload *flow)
 {
+	clear_bit(IPS_OFFLOAD_BIT, &flow->ct->status);
 	set_bit(NF_FLOW_TEARDOWN, &flow->flags);
-
-	flow_offload_fixup_ct_state(flow->ct);
+	flow_offload_fixup_ct(flow->ct);
 }
 EXPORT_SYMBOL_GPL(flow_offload_teardown);
 
@@ -399,7 +375,8 @@
 
 static int
 nf_flow_table_iterate(struct nf_flowtable *flow_table,
-		      void (*iter)(struct flow_offload *flow, void *data),
+		      void (*iter)(struct nf_flowtable *flowtable,
+				   struct flow_offload *flow, void *data),
 		      void *data)
 {
 	struct flow_offload_tuple_rhash *tuplehash;
@@ -423,7 +400,7 @@
 
 		flow = container_of(tuplehash, struct flow_offload, tuplehash[0]);
 
-		iter(flow, data);
+		iter(flow_table, flow, data);
 	}
 	rhashtable_walk_stop(&hti);
 	rhashtable_walk_exit(&hti);
@@ -431,34 +408,12 @@
 	return err;
 }
 
-static bool flow_offload_stale_dst(struct flow_offload_tuple *tuple)
+static void nf_flow_offload_gc_step(struct nf_flowtable *flow_table,
+				    struct flow_offload *flow, void *data)
 {
-	struct dst_entry *dst;
-
-	if (tuple->xmit_type == FLOW_OFFLOAD_XMIT_NEIGH ||
-	    tuple->xmit_type == FLOW_OFFLOAD_XMIT_XFRM) {
-		dst = tuple->dst_cache;
-		if (!dst_check(dst, tuple->dst_cookie))
-			return true;
-	}
-
-	return false;
-}
-
-static bool nf_flow_has_stale_dst(struct flow_offload *flow)
-{
-	return flow_offload_stale_dst(&flow->tuplehash[FLOW_OFFLOAD_DIR_ORIGINAL].tuple) ||
-	       flow_offload_stale_dst(&flow->tuplehash[FLOW_OFFLOAD_DIR_REPLY].tuple);
-}
-
-static void nf_flow_offload_gc_step(struct flow_offload *flow, void *data)
-{
-	struct nf_flowtable *flow_table = data;
-
 	if (nf_flow_has_expired(flow) ||
-	    nf_ct_is_dying(flow->ct) ||
-	    nf_flow_has_stale_dst(flow))
-		set_bit(NF_FLOW_TEARDOWN, &flow->flags);
+	    nf_ct_is_dying(flow->ct))
+		flow_offload_teardown(flow);
 
 	if (test_bit(NF_FLOW_TEARDOWN, &flow->flags)) {
 		if (test_bit(NF_FLOW_HW, &flow->flags)) {
@@ -474,12 +429,17 @@
 	}
 }
 
+void nf_flow_table_gc_run(struct nf_flowtable *flow_table)
+{
+	nf_flow_table_iterate(flow_table, nf_flow_offload_gc_step, NULL);
+}
+
 static void nf_flow_offload_work_gc(struct work_struct *work)
 {
 	struct nf_flowtable *flow_table;
 
 	flow_table = container_of(work, struct nf_flowtable, gc_work.work);
-	nf_flow_table_iterate(flow_table, nf_flow_offload_gc_step, flow_table);
+	nf_flow_table_gc_run(flow_table);
 	queue_delayed_work(system_power_efficient_wq, &flow_table->gc_work, HZ);
 }
 
@@ -595,7 +555,8 @@
 }
 EXPORT_SYMBOL_GPL(nf_flow_table_init);
 
-static void nf_flow_table_do_cleanup(struct flow_offload *flow, void *data)
+static void nf_flow_table_do_cleanup(struct nf_flowtable *flow_table,
+				     struct flow_offload *flow, void *data)
 {
 	struct net_device *dev = data;
 
@@ -636,24 +597,83 @@
 	mutex_unlock(&flowtable_lock);
 
 	cancel_delayed_work_sync(&flow_table->gc_work);
-	nf_flow_table_iterate(flow_table, nf_flow_table_do_cleanup, NULL);
-	nf_flow_table_iterate(flow_table, nf_flow_offload_gc_step, flow_table);
 	nf_flow_table_offload_flush(flow_table);
-	if (nf_flowtable_hw_offload(flow_table))
-		nf_flow_table_iterate(flow_table, nf_flow_offload_gc_step,
-				      flow_table);
+	/* ... no more pending work after this stage ... */
+	nf_flow_table_iterate(flow_table, nf_flow_table_do_cleanup, NULL);
+	nf_flow_table_gc_run(flow_table);
+	nf_flow_table_offload_flush_cleanup(flow_table);
 	rhashtable_destroy(&flow_table->rhashtable);
 }
 EXPORT_SYMBOL_GPL(nf_flow_table_free);
 
+static int nf_flow_table_init_net(struct net *net)
+{
+	net->ft.stat = alloc_percpu(struct nf_flow_table_stat);
+	return net->ft.stat ? 0 : -ENOMEM;
+}
+
+static void nf_flow_table_fini_net(struct net *net)
+{
+	free_percpu(net->ft.stat);
+}
+
+static int nf_flow_table_pernet_init(struct net *net)
+{
+	int ret;
+
+	ret = nf_flow_table_init_net(net);
+	if (ret < 0)
+		return ret;
+
+	ret = nf_flow_table_init_proc(net);
+	if (ret < 0)
+		goto out_proc;
+
+	return 0;
+
+out_proc:
+	nf_flow_table_fini_net(net);
+	return ret;
+}
+
+static void nf_flow_table_pernet_exit(struct list_head *net_exit_list)
+{
+	struct net *net;
+
+	list_for_each_entry(net, net_exit_list, exit_list) {
+		nf_flow_table_fini_proc(net);
+		nf_flow_table_fini_net(net);
+	}
+}
+
+static struct pernet_operations nf_flow_table_net_ops = {
+	.init = nf_flow_table_pernet_init,
+	.exit_batch = nf_flow_table_pernet_exit,
+};
+
 static int __init nf_flow_table_module_init(void)
 {
-	return nf_flow_table_offload_init();
+	int ret;
+
+	ret = register_pernet_subsys(&nf_flow_table_net_ops);
+	if (ret < 0)
+		return ret;
+
+	ret = nf_flow_table_offload_init();
+	if (ret)
+		goto out_offload;
+
+	return 0;
+
+out_offload:
+	unregister_pernet_subsys(&nf_flow_table_net_ops);
+	return ret;
 }
 
 static void __exit nf_flow_table_module_exit(void)
 {
 	nf_flow_table_offload_exit();
+	unregister_pernet_subsys(&nf_flow_table_net_ops);
 }
 
 module_init(nf_flow_table_module_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_flow_table_inet.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_flow_table_inet.c
@@ -6,12 +6,33 @@
 #include <linux/rhashtable.h>
 #include <net/netfilter/nf_flow_table.h>
 #include <net/netfilter/nf_tables.h>
+#include <linux/if_vlan.h>
 
 static unsigned int
 nf_flow_offload_inet_hook(void *priv, struct sk_buff *skb,
 			  const struct nf_hook_state *state)
 {
+	struct vlan_ethhdr *veth;
+	__be16 proto;
+
 	switch (skb->protocol) {
+	case htons(ETH_P_8021Q):
+		if (!pskb_may_pull(skb, skb_mac_offset(skb) + sizeof(*veth)))
+			return NF_ACCEPT;
+
+		veth = (struct vlan_ethhdr *)skb_mac_header(skb);
+		proto = veth->h_vlan_encapsulated_proto;
+		break;
+	case htons(ETH_P_PPP_SES):
+		if (!nf_flow_pppoe_proto(skb, &proto))
+			return NF_ACCEPT;
+		break;
+	default:
+		proto = skb->protocol;
+		break;
+	}
+
+	switch (proto) {
 	case htons(ETH_P_IP):
 		return nf_flow_offload_ip_hook(priv, skb, state);
 	case htons(ETH_P_IPV6):
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_flow_table_ip.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_flow_table_ip.c
@@ -8,8 +8,6 @@
 #include <linux/ipv6.h>
 #include <linux/netdevice.h>
 #include <linux/if_ether.h>
-#include <linux/if_pppox.h>
-#include <linux/ppp_defs.h>
 #include <net/ip.h>
 #include <net/ipv6.h>
 #include <net/ip6_route.h>
@@ -158,7 +156,7 @@
 		tuple->encap[i].proto = skb->protocol;
 		break;
 	case htons(ETH_P_PPP_SES):
-		phdr = (struct pppoe_hdr *)skb_mac_header(skb);
+		phdr = (struct pppoe_hdr *)skb_network_header(skb);
 		tuple->encap[i].id = ntohs(phdr->sid);
 		tuple->encap[i].proto = skb->protocol;
 		break;
@@ -229,6 +227,15 @@
 	return true;
 }
 
+static inline bool nf_flow_dst_check(struct flow_offload_tuple *tuple)
+{
+	if (tuple->xmit_type != FLOW_OFFLOAD_XMIT_NEIGH &&
+	    tuple->xmit_type != FLOW_OFFLOAD_XMIT_XFRM)
+		return true;
+
+	return dst_check(tuple->dst_cache, tuple->dst_cookie);
+}
+
 static unsigned int nf_flow_xmit_xfrm(struct sk_buff *skb,
 				      const struct nf_hook_state *state,
 				      struct dst_entry *dst)
@@ -239,29 +246,17 @@
 	return NF_STOLEN;
 }
 
-static inline __be16 nf_flow_pppoe_proto(const struct sk_buff *skb)
-{
-	__be16 proto;
-
-	proto = *((__be16 *)(skb_mac_header(skb) + ETH_HLEN +
-			     sizeof(struct pppoe_hdr)));
-	switch (proto) {
-	case htons(PPP_IP):
-		return htons(ETH_P_IP);
-	case htons(PPP_IPV6):
-		return htons(ETH_P_IPV6);
-	}
-
-	return 0;
-}
-
-static bool nf_flow_skb_encap_protocol(const struct sk_buff *skb, __be16 proto,
+static bool nf_flow_skb_encap_protocol(struct sk_buff *skb, __be16 proto,
 				       u32 *offset)
 {
 	struct vlan_ethhdr *veth;
+	__be16 inner_proto;
 
 	switch (skb->protocol) {
 	case htons(ETH_P_8021Q):
+		if (!pskb_may_pull(skb, skb_mac_offset(skb) + sizeof(*veth)))
+			return false;
+
 		veth = (struct vlan_ethhdr *)skb_mac_header(skb);
 		if (veth->h_vlan_encapsulated_proto == proto) {
 			*offset += VLAN_HLEN;
@@ -269,7 +264,8 @@
 		}
 		break;
 	case htons(ETH_P_PPP_SES):
-		if (nf_flow_pppoe_proto(skb) == proto) {
+		if (nf_flow_pppoe_proto(skb, &inner_proto) &&
+		    inner_proto == proto) {
 			*offset += PPPOE_SES_HLEN;
 			return true;
 		}
@@ -298,7 +294,7 @@
 			skb_reset_network_header(skb);
 			break;
 		case htons(ETH_P_PPP_SES):
-			skb->protocol = nf_flow_pppoe_proto(skb);
+			skb->protocol = __nf_flow_pppoe_proto(skb);
 			skb_pull(skb, PPPOE_SES_HLEN);
 			skb_reset_network_header(skb);
 			break;
@@ -364,6 +360,11 @@
 	if (nf_flow_state_check(flow, iph->protocol, skb, thoff))
 		return NF_ACCEPT;
 
+	if (!nf_flow_dst_check(&tuplehash->tuple)) {
+		flow_offload_teardown(flow);
+		return NF_ACCEPT;
+	}
+
 	if (skb_try_make_writable(skb, thoff + hdrsize))
 		return NF_DROP;
 
@@ -600,6 +601,11 @@
 	if (nf_flow_state_check(flow, ip6h->nexthdr, skb, thoff))
 		return NF_ACCEPT;
 
+	if (!nf_flow_dst_check(&tuplehash->tuple)) {
+		flow_offload_teardown(flow);
+		return NF_ACCEPT;
+	}
+
 	if (skb_try_make_writable(skb, thoff + hdrsize))
 		return NF_DROP;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_flow_table_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_flow_table_offload.c
@@ -65,11 +65,11 @@
 		       sizeof(struct in6_addr));
 		if (memcmp(&key->enc_ipv6.src, &in6addr_any,
 			   sizeof(struct in6_addr)))
-			memset(&key->enc_ipv6.src, 0xff,
+			memset(&mask->enc_ipv6.src, 0xff,
 			       sizeof(struct in6_addr));
 		if (memcmp(&key->enc_ipv6.dst, &in6addr_any,
 			   sizeof(struct in6_addr)))
-			memset(&key->enc_ipv6.dst, 0xff,
+			memset(&mask->enc_ipv6.dst, 0xff,
 			       sizeof(struct in6_addr));
 		enc_keys |= BIT(FLOW_DISSECTOR_KEY_ENC_IPV6_ADDRS);
 		key->enc_control.addr_type = FLOW_DISSECTOR_KEY_IPV6_ADDRS;
@@ -372,12 +372,12 @@
 				     const __be32 *addr, const __be32 *mask)
 {
 	struct flow_action_entry *entry;
-	int i, j;
+	int i;
 
-	for (i = 0, j = 0; i < sizeof(struct in6_addr) / sizeof(u32); i += sizeof(u32), j++) {
+	for (i = 0; i < sizeof(struct in6_addr) / sizeof(u32); i++) {
 		entry = flow_action_entry_next(flow_rule);
 		flow_offload_mangle(entry, FLOW_ACT_MANGLE_HDR_TYPE_IP6,
-				    offset + i, &addr[j], mask);
+				    offset + i * sizeof(u32), &addr[i], mask);
 	}
 }
 
@@ -830,8 +830,8 @@
 				 struct list_head *block_cb_list)
 {
 	struct flow_cls_offload cls_flow = {};
+	struct netlink_ext_ack extack = {};
 	struct flow_block_cb *block_cb;
-	struct netlink_ext_ack extack;
 	__be16 proto = ETH_P_ALL;
 	int err, i = 0;
 
@@ -953,17 +953,22 @@
 static void flow_offload_work_handler(struct work_struct *work)
 {
 	struct flow_offload_work *offload;
+	struct net *net;
 
 	offload = container_of(work, struct flow_offload_work, work);
+	net = read_pnet(&offload->flowtable->net);
 	switch (offload->cmd) {
 		case FLOW_CLS_REPLACE:
 			flow_offload_work_add(offload);
+			NF_FLOW_TABLE_STAT_DEC_ATOMIC(net, count_wq_add);
 			break;
 		case FLOW_CLS_DESTROY:
 			flow_offload_work_del(offload);
+			NF_FLOW_TABLE_STAT_DEC_ATOMIC(net, count_wq_del);
 			break;
 		case FLOW_CLS_STATS:
 			flow_offload_work_stats(offload);
+			NF_FLOW_TABLE_STAT_DEC_ATOMIC(net, count_wq_stats);
 			break;
 		default:
 			WARN_ON_ONCE(1);
@@ -975,12 +980,18 @@
 
 static void flow_offload_queue_work(struct flow_offload_work *offload)
 {
-	if (offload->cmd == FLOW_CLS_REPLACE)
+	struct net *net = read_pnet(&offload->flowtable->net);
+
+	if (offload->cmd == FLOW_CLS_REPLACE) {
+		NF_FLOW_TABLE_STAT_INC(net, count_wq_add);
 		queue_work(nf_flow_offload_add_wq, &offload->work);
-	else if (offload->cmd == FLOW_CLS_DESTROY)
+	} else if (offload->cmd == FLOW_CLS_DESTROY) {
+		NF_FLOW_TABLE_STAT_INC(net, count_wq_del);
 		queue_work(nf_flow_offload_del_wq, &offload->work);
-	else
+	} else {
+		NF_FLOW_TABLE_STAT_INC(net, count_wq_stats);
 		queue_work(nf_flow_offload_stats_wq, &offload->work);
+	}
 }
 
 static struct flow_offload_work *
@@ -1050,6 +1061,14 @@
 	flow_offload_queue_work(offload);
 }
 
+void nf_flow_table_offload_flush_cleanup(struct nf_flowtable *flowtable)
+{
+	if (nf_flowtable_hw_offload(flowtable)) {
+		flush_workqueue(nf_flow_offload_del_wq);
+		nf_flow_table_gc_run(flowtable);
+	}
+}
+
 void nf_flow_table_offload_flush(struct nf_flowtable *flowtable)
 {
 	if (nf_flowtable_hw_offload(flowtable)) {
@@ -1066,6 +1085,7 @@
 	struct flow_block_cb *block_cb, *next;
 	int err = 0;
 
+	down_write(&flowtable->flow_block_lock);
 	switch (cmd) {
 	case FLOW_BLOCK_BIND:
 		list_splice(&bo->cb_list, &flowtable->flow_block.cb_list);
@@ -1080,6 +1100,7 @@
 		WARN_ON_ONCE(1);
 		err = -EOPNOTSUPP;
 	}
+	up_write(&flowtable->flow_block_lock);
 
 	return err;
 }
@@ -1136,7 +1157,9 @@
 
 	nf_flow_table_block_offload_init(bo, dev_net(dev), cmd, flowtable,
 					 extack);
+	down_write(&flowtable->flow_block_lock);
 	err = dev->netdev_ops->ndo_setup_tc(dev, TC_SETUP_FT, bo);
+	up_write(&flowtable->flow_block_lock);
 	if (err < 0)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_flow_table_procfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_flow_table_procfs.c
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/kernel.h>
+#include <linux/proc_fs.h>
+#include <net/netfilter/nf_flow_table.h>
+
+static void *nf_flow_table_cpu_seq_start(struct seq_file *seq, loff_t *pos)
+{
+	struct net *net = seq_file_net(seq);
+	int cpu;
+
+	if (*pos == 0)
+		return SEQ_START_TOKEN;
+
+	for (cpu = *pos - 1; cpu < nr_cpu_ids; ++cpu) {
+		if (!cpu_possible(cpu))
+			continue;
+		*pos = cpu + 1;
+		return per_cpu_ptr(net->ft.stat, cpu);
+	}
+
+	return NULL;
+}
+
+static void *nf_flow_table_cpu_seq_next(struct seq_file *seq, void *v, loff_t *pos)
+{
+	struct net *net = seq_file_net(seq);
+	int cpu;
+
+	for (cpu = *pos; cpu < nr_cpu_ids; ++cpu) {
+		if (!cpu_possible(cpu))
+			continue;
+		*pos = cpu + 1;
+		return per_cpu_ptr(net->ft.stat, cpu);
+	}
+	(*pos)++;
+	return NULL;
+}
+
+static void nf_flow_table_cpu_seq_stop(struct seq_file *seq, void *v)
+{
+}
+
+static int nf_flow_table_cpu_seq_show(struct seq_file *seq, void *v)
+{
+	const struct nf_flow_table_stat *st = v;
+
+	if (v == SEQ_START_TOKEN) {
+		seq_puts(seq, "wq_add   wq_del   wq_stats\n");
+		return 0;
+	}
+
+	seq_printf(seq, "%8d %8d %8d\n",
+		   st->count_wq_add,
+		   st->count_wq_del,
+		   st->count_wq_stats
+		);
+	return 0;
+}
+
+static const struct seq_operations nf_flow_table_cpu_seq_ops = {
+	.start	= nf_flow_table_cpu_seq_start,
+	.next	= nf_flow_table_cpu_seq_next,
+	.stop	= nf_flow_table_cpu_seq_stop,
+	.show	= nf_flow_table_cpu_seq_show,
+};
+
+int nf_flow_table_init_proc(struct net *net)
+{
+	struct proc_dir_entry *pde;
+
+	pde = proc_create_net("nf_flowtable", 0444, net->proc_net_stat,
+			      &nf_flow_table_cpu_seq_ops,
+			      sizeof(struct seq_net_private));
+	return pde ? 0 : -ENOMEM;
+}
+
+void nf_flow_table_fini_proc(struct net *net)
+{
+	remove_proc_entry("nf_flowtable", net->proc_net_stat);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_log.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_log.c
@@ -193,11 +193,12 @@
 		return;
 	}
 
-	BUG_ON(loggers[pf][type] == NULL);
-
 	rcu_read_lock();
 	logger = rcu_dereference(loggers[pf][type]);
-	module_put(logger->me);
+	if (!logger)
+		WARN_ON_ONCE(1);
+	else
+		module_put(logger->me);
 	rcu_read_unlock();
 }
 EXPORT_SYMBOL_GPL(nf_logger_put);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_log_syslog.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_log_syslog.c
@@ -61,7 +61,7 @@
 	unsigned int logflags;
 	struct arphdr _arph;
 
-	ah = skb_header_pointer(skb, 0, sizeof(_arph), &_arph);
+	ah = skb_header_pointer(skb, nhoff, sizeof(_arph), &_arph);
 	if (!ah) {
 		nf_log_buf_add(m, "TRUNCATED");
 		return;
@@ -90,7 +90,7 @@
 	    ah->ar_pln != sizeof(__be32))
 		return;
 
-	ap = skb_header_pointer(skb, sizeof(_arph), sizeof(_arpp), &_arpp);
+	ap = skb_header_pointer(skb, nhoff + sizeof(_arph), sizeof(_arpp), &_arpp);
 	if (!ap) {
 		nf_log_buf_add(m, " INCOMPLETE [%zu bytes]",
 			       skb->len - sizeof(_arph));
@@ -144,7 +144,7 @@
 
 	nf_log_dump_packet_common(m, pf, hooknum, skb, in, out, loginfo,
 				  prefix);
-	dump_arp_packet(m, loginfo, skb, 0);
+	dump_arp_packet(m, loginfo, skb, skb_network_offset(skb));
 
 	nf_log_buf_close(m);
 }
@@ -829,7 +829,7 @@
 	if (in)
 		dump_ipv4_mac_header(m, loginfo, skb);
 
-	dump_ipv4_packet(net, m, loginfo, skb, 0);
+	dump_ipv4_packet(net, m, loginfo, skb, skb_network_offset(skb));
 
 	nf_log_buf_close(m);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_nat_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_nat_core.c
@@ -1120,7 +1120,7 @@
 	.size = sizeof(struct nat_net),
 };
 
-static struct nf_nat_hook nat_hook = {
+static const struct nf_nat_hook nat_hook = {
 	.parse_nat_setup	= nfnetlink_parse_nat_setup,
 #ifdef CONFIG_XFRM
 	.decode_session		= __nf_nat_decode_session,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_nat_redirect.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_nat_redirect.c
@@ -10,6 +10,7 @@
 
 #include <linux/if.h>
 #include <linux/inetdevice.h>
+#include <linux/in.h>
 #include <linux/ip.h>
 #include <linux/kernel.h>
 #include <linux/netdevice.h>
@@ -24,81 +25,104 @@
 #include <net/netfilter/nf_nat.h>
 #include <net/netfilter/nf_nat_redirect.h>
 
+static unsigned int
+nf_nat_redirect(struct sk_buff *skb, const struct nf_nat_range2 *range,
+		const union nf_inet_addr *newdst)
+{
+	struct nf_nat_range2 newrange;
+	enum ip_conntrack_info ctinfo;
+	struct nf_conn *ct;
+
+	ct = nf_ct_get(skb, &ctinfo);
+
+	memset(&newrange, 0, sizeof(newrange));
+
+	newrange.flags		= range->flags | NF_NAT_RANGE_MAP_IPS;
+	newrange.min_addr	= *newdst;
+	newrange.max_addr	= *newdst;
+	newrange.min_proto	= range->min_proto;
+	newrange.max_proto	= range->max_proto;
+
+	return nf_nat_setup_info(ct, &newrange, NF_NAT_MANIP_DST);
+}
+
 unsigned int
-nf_nat_redirect_ipv4(struct sk_buff *skb,
-		     const struct nf_nat_ipv4_multi_range_compat *mr,
+nf_nat_redirect_ipv4(struct sk_buff *skb, const struct nf_nat_range2 *range,
 		     unsigned int hooknum)
 {
-	struct nf_conn *ct;
-	enum ip_conntrack_info ctinfo;
-	__be32 newdst;
-	struct nf_nat_range2 newrange;
+	union nf_inet_addr newdst = {};
 
 	WARN_ON(hooknum != NF_INET_PRE_ROUTING &&
 		hooknum != NF_INET_LOCAL_OUT);
 
-	ct = nf_ct_get(skb, &ctinfo);
-	WARN_ON(!(ct && (ctinfo == IP_CT_NEW || ctinfo == IP_CT_RELATED)));
-
 	/* Local packets: make them go to loopback */
 	if (hooknum == NF_INET_LOCAL_OUT) {
-		newdst = htonl(0x7F000001);
+		newdst.ip = htonl(INADDR_LOOPBACK);
 	} else {
 		const struct in_device *indev;
 
-		newdst = 0;
-
 		indev = __in_dev_get_rcu(skb->dev);
 		if (indev) {
 			const struct in_ifaddr *ifa;
 
 			ifa = rcu_dereference(indev->ifa_list);
 			if (ifa)
-				newdst = ifa->ifa_local;
+				newdst.ip = ifa->ifa_local;
 		}
 
-		if (!newdst)
+		if (!newdst.ip)
 			return NF_DROP;
 	}
 
-	/* Transfer from original range. */
-	memset(&newrange.min_addr, 0, sizeof(newrange.min_addr));
-	memset(&newrange.max_addr, 0, sizeof(newrange.max_addr));
-	newrange.flags	     = mr->range[0].flags | NF_NAT_RANGE_MAP_IPS;
-	newrange.min_addr.ip = newdst;
-	newrange.max_addr.ip = newdst;
-	newrange.min_proto   = mr->range[0].min;
-	newrange.max_proto   = mr->range[0].max;
-
-	/* Hand modified range to generic setup. */
-	return nf_nat_setup_info(ct, &newrange, NF_NAT_MANIP_DST);
+	return nf_nat_redirect(skb, range, &newdst);
 }
 EXPORT_SYMBOL_GPL(nf_nat_redirect_ipv4);
 
 static const struct in6_addr loopback_addr = IN6ADDR_LOOPBACK_INIT;
 
+static bool nf_nat_redirect_ipv6_usable(const struct inet6_ifaddr *ifa, unsigned int scope)
+{
+	unsigned int ifa_addr_type = ipv6_addr_type(&ifa->addr);
+
+	if (ifa_addr_type & IPV6_ADDR_MAPPED)
+		return false;
+
+	if ((ifa->flags & IFA_F_TENTATIVE) && (!(ifa->flags & IFA_F_OPTIMISTIC)))
+		return false;
+
+	if (scope) {
+		unsigned int ifa_scope = ifa_addr_type & IPV6_ADDR_SCOPE_MASK;
+
+		if (!(scope & ifa_scope))
+			return false;
+	}
+
+	return true;
+}
+
 unsigned int
 nf_nat_redirect_ipv6(struct sk_buff *skb, const struct nf_nat_range2 *range,
 		     unsigned int hooknum)
 {
-	struct nf_nat_range2 newrange;
-	struct in6_addr newdst;
-	enum ip_conntrack_info ctinfo;
-	struct nf_conn *ct;
+	union nf_inet_addr newdst = {};
 
-	ct = nf_ct_get(skb, &ctinfo);
 	if (hooknum == NF_INET_LOCAL_OUT) {
-		newdst = loopback_addr;
+		newdst.in6 = loopback_addr;
 	} else {
+		unsigned int scope = ipv6_addr_scope(&ipv6_hdr(skb)->daddr);
 		struct inet6_dev *idev;
-		struct inet6_ifaddr *ifa;
 		bool addr = false;
 
 		idev = __in6_dev_get(skb->dev);
 		if (idev != NULL) {
+			const struct inet6_ifaddr *ifa;
+
 			read_lock_bh(&idev->lock);
 			list_for_each_entry(ifa, &idev->addr_list, if_list) {
-				newdst = ifa->addr;
+				if (!nf_nat_redirect_ipv6_usable(ifa, scope))
+					continue;
+
+				newdst.in6 = ifa->addr;
 				addr = true;
 				break;
 			}
@@ -109,12 +133,6 @@
 			return NF_DROP;
 	}
 
-	newrange.flags		= range->flags | NF_NAT_RANGE_MAP_IPS;
-	newrange.min_addr.in6	= newdst;
-	newrange.max_addr.in6	= newdst;
-	newrange.min_proto	= range->min_proto;
-	newrange.max_proto	= range->max_proto;
-
-	return nf_nat_setup_info(ct, &newrange, NF_NAT_MANIP_DST);
+	return nf_nat_redirect(skb, range, &newdst);
 }
 EXPORT_SYMBOL_GPL(nf_nat_redirect_ipv6);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_queue.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_queue.c
@@ -46,6 +46,15 @@
 }
 EXPORT_SYMBOL(nf_unregister_queue_handler);
 
+static void nf_queue_sock_put(struct sock *sk)
+{
+#ifdef CONFIG_INET
+	sock_gen_put(sk);
+#else
+	sock_put(sk);
+#endif
+}
+
 static void nf_queue_entry_release_refs(struct nf_queue_entry *entry)
 {
 	struct nf_hook_state *state = &entry->state;
@@ -54,7 +63,7 @@
 	dev_put(state->in);
 	dev_put(state->out);
 	if (state->sk)
-		sock_put(state->sk);
+		nf_queue_sock_put(state->sk);
 
 #if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
 	dev_put(entry->physin);
@@ -87,19 +96,21 @@
 }
 
 /* Bump dev refs so they don't vanish while packet is out */
-void nf_queue_entry_get_refs(struct nf_queue_entry *entry)
+bool nf_queue_entry_get_refs(struct nf_queue_entry *entry)
 {
 	struct nf_hook_state *state = &entry->state;
 
+	if (state->sk && !refcount_inc_not_zero(&state->sk->sk_refcnt))
+		return false;
+
 	dev_hold(state->in);
 	dev_hold(state->out);
-	if (state->sk)
-		sock_hold(state->sk);
 
 #if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
 	dev_hold(entry->physin);
 	dev_hold(entry->physout);
 #endif
+	return true;
 }
 EXPORT_SYMBOL_GPL(nf_queue_entry_get_refs);
 
@@ -169,6 +180,18 @@
 		break;
 	}
 
+	if (skb_sk_is_prefetched(skb)) {
+		struct sock *sk = skb->sk;
+
+		if (!sk_is_refcounted(sk)) {
+			if (!refcount_inc_not_zero(&sk->sk_refcnt))
+				return -ENOTCONN;
+
+			/* drop refcount on skb_orphan */
+			skb->destructor = sock_edemux;
+		}
+	}
+
 	entry = kmalloc(sizeof(*entry) + route_key_size, GFP_ATOMIC);
 	if (!entry)
 		return -ENOMEM;
@@ -187,7 +210,10 @@
 
 	__nf_queue_entry_init_physdevs(entry);
 
-	nf_queue_entry_get_refs(entry);
+	if (!nf_queue_entry_get_refs(entry)) {
+		kfree(entry);
+		return -ENOTCONN;
+	}
 
 	switch (entry->state.pf) {
 	case AF_INET:
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_synproxy_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_synproxy_core.c
@@ -349,7 +349,6 @@
 		goto err2;
 
 	__set_bit(IPS_CONFIRMED_BIT, &ct->status);
-	nf_conntrack_get(&ct->ct_general);
 	snet->tmpl = ct;
 
 	snet->stats = alloc_percpu(struct synproxy_stats);
@@ -428,7 +427,7 @@
 	iph->tos	= 0;
 	iph->id		= 0;
 	iph->frag_off	= htons(IP_DF);
-	iph->ttl	= net->ipv4.sysctl_ip_default_ttl;
+	iph->ttl	= READ_ONCE(net->ipv4.sysctl_ip_default_ttl);
 	iph->protocol	= IPPROTO_TCP;
 	iph->check	= 0;
 	iph->saddr	= saddr;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_tables_api.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_tables_api.c
@@ -24,6 +24,7 @@
 #include <net/sock.h>
 
 #define NFT_MODULE_AUTOLOAD_LIMIT (MODULE_NAME_LEN - sizeof("nft-expr-255-"))
+#define NFT_SET_MAX_ANONLEN 16
 
 unsigned int nf_tables_net_id __read_mostly;
 
@@ -31,8 +32,9 @@
 static LIST_HEAD(nf_tables_objects);
 static LIST_HEAD(nf_tables_flowtables);
 static LIST_HEAD(nf_tables_destroy_list);
+static LIST_HEAD(nf_tables_gc_list);
 static DEFINE_SPINLOCK(nf_tables_destroy_list_lock);
-static u64 table_handle;
+static DEFINE_SPINLOCK(nf_tables_gc_list_lock);
 
 enum {
 	NFT_VALIDATE_SKIP	= 0,
@@ -123,6 +125,9 @@
 static void nf_tables_trans_destroy_work(struct work_struct *w);
 static DECLARE_WORK(trans_destroy_work, nf_tables_trans_destroy_work);
 
+static void nft_trans_gc_work(struct work_struct *work);
+static DECLARE_WORK(trans_gc_work, nft_trans_gc_work);
+
 static void nft_ctx_init(struct nft_ctx *ctx,
 			 struct net *net,
 			 const struct sk_buff *skb,
@@ -153,6 +158,8 @@
 	if (trans == NULL)
 		return NULL;
 
+	INIT_LIST_HEAD(&trans->list);
+	INIT_LIST_HEAD(&trans->binding_list);
 	trans->msg_type = msg_type;
 	trans->ctx	= *ctx;
 
@@ -165,13 +172,20 @@
 	return nft_trans_alloc_gfp(ctx, msg_type, size, GFP_KERNEL);
 }
 
-static void nft_trans_destroy(struct nft_trans *trans)
+static void nft_trans_list_del(struct nft_trans *trans)
 {
 	list_del(&trans->list);
+	list_del(&trans->binding_list);
+}
+
+static void nft_trans_destroy(struct nft_trans *trans)
+{
+	nft_trans_list_del(trans);
 	kfree(trans);
 }
 
-static void nft_set_trans_bind(const struct nft_ctx *ctx, struct nft_set *set)
+static void __nft_set_trans_bind(const struct nft_ctx *ctx, struct nft_set *set,
+				 bool bind)
 {
 	struct nftables_pernet *nft_net;
 	struct net *net = ctx->net;
@@ -185,16 +199,82 @@
 		switch (trans->msg_type) {
 		case NFT_MSG_NEWSET:
 			if (nft_trans_set(trans) == set)
-				nft_trans_set_bound(trans) = true;
+				nft_trans_set_bound(trans) = bind;
 			break;
 		case NFT_MSG_NEWSETELEM:
 			if (nft_trans_elem_set(trans) == set)
-				nft_trans_elem_set_bound(trans) = true;
+				nft_trans_elem_set_bound(trans) = bind;
+			break;
+		}
+	}
+}
+
+static void nft_set_trans_bind(const struct nft_ctx *ctx, struct nft_set *set)
+{
+	return __nft_set_trans_bind(ctx, set, true);
+}
+
+static void nft_set_trans_unbind(const struct nft_ctx *ctx, struct nft_set *set)
+{
+	return __nft_set_trans_bind(ctx, set, false);
+}
+
+static void __nft_chain_trans_bind(const struct nft_ctx *ctx,
+				   struct nft_chain *chain, bool bind)
+{
+	struct nftables_pernet *nft_net;
+	struct net *net = ctx->net;
+	struct nft_trans *trans;
+
+	if (!nft_chain_binding(chain))
+		return;
+
+	nft_net = nft_pernet(net);
+	list_for_each_entry_reverse(trans, &nft_net->commit_list, list) {
+		switch (trans->msg_type) {
+		case NFT_MSG_NEWCHAIN:
+			if (nft_trans_chain(trans) == chain)
+				nft_trans_chain_bound(trans) = bind;
+			break;
+		case NFT_MSG_NEWRULE:
+			if (trans->ctx.chain == chain)
+				nft_trans_rule_bound(trans) = bind;
 			break;
 		}
 	}
 }
 
+static void nft_chain_trans_bind(const struct nft_ctx *ctx,
+				 struct nft_chain *chain)
+{
+	__nft_chain_trans_bind(ctx, chain, true);
+}
+
+int nf_tables_bind_chain(const struct nft_ctx *ctx, struct nft_chain *chain)
+{
+	if (!nft_chain_binding(chain))
+		return 0;
+
+	if (nft_chain_binding(ctx->chain))
+		return -EOPNOTSUPP;
+
+	if (chain->bound)
+		return -EBUSY;
+
+	if (!nft_use_inc(&chain->use))
+		return -EMFILE;
+
+	chain->bound = true;
+	nft_chain_trans_bind(ctx, chain);
+
+	return 0;
+}
+
+void nf_tables_unbind_chain(const struct nft_ctx *ctx, struct nft_chain *chain)
+{
+	__nft_chain_trans_bind(ctx, chain, false);
+}
+
 static int nft_netdev_register_hooks(struct net *net,
 				     struct list_head *hook_list)
 {
@@ -222,12 +302,18 @@
 }
 
 static void nft_netdev_unregister_hooks(struct net *net,
-					struct list_head *hook_list)
+					struct list_head *hook_list,
+					bool release_netdev)
 {
-	struct nft_hook *hook;
+	struct nft_hook *hook, *next;
 
-	list_for_each_entry(hook, hook_list, list)
+	list_for_each_entry_safe(hook, next, hook_list, list) {
 		nf_unregister_net_hook(net, &hook->ops);
+		if (release_netdev) {
+			list_del(&hook->list);
+			kfree_rcu(hook, rcu);
+		}
+	}
 }
 
 static int nf_tables_register_hook(struct net *net,
@@ -253,9 +339,10 @@
 	return nf_register_net_hook(net, &basechain->ops);
 }
 
-static void nf_tables_unregister_hook(struct net *net,
-				      const struct nft_table *table,
-				      struct nft_chain *chain)
+static void __nf_tables_unregister_hook(struct net *net,
+					const struct nft_table *table,
+					struct nft_chain *chain,
+					bool release_netdev)
 {
 	struct nft_base_chain *basechain;
 	const struct nf_hook_ops *ops;
@@ -270,15 +357,36 @@
 		return basechain->type->ops_unregister(net, ops);
 
 	if (nft_base_chain_netdev(table->family, basechain->ops.hooknum))
-		nft_netdev_unregister_hooks(net, &basechain->hook_list);
+		nft_netdev_unregister_hooks(net, &basechain->hook_list,
+					    release_netdev);
 	else
 		nf_unregister_net_hook(net, &basechain->ops);
 }
 
+static void nf_tables_unregister_hook(struct net *net,
+				      const struct nft_table *table,
+				      struct nft_chain *chain)
+{
+	return __nf_tables_unregister_hook(net, table, chain, false);
+}
+
 static void nft_trans_commit_list_add_tail(struct net *net, struct nft_trans *trans)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
 
+	switch (trans->msg_type) {
+	case NFT_MSG_NEWSET:
+		if (!nft_trans_set_update(trans) &&
+		    nft_set_is_anonymous(nft_trans_set(trans)))
+			list_add_tail(&trans->binding_list, &nft_net->binding_list);
+		break;
+	case NFT_MSG_NEWCHAIN:
+		if (!nft_trans_chain_update(trans) &&
+		    nft_chain_binding(nft_trans_chain(trans)))
+			list_add_tail(&trans->binding_list, &nft_net->binding_list);
+		break;
+	}
+
 	list_add_tail(&trans->list, &nft_net->commit_list);
 }
 
@@ -325,8 +433,9 @@
 				ntohl(nla_get_be32(ctx->nla[NFTA_CHAIN_ID]));
 		}
 	}
-
+	nft_trans_chain(trans) = ctx->chain;
 	nft_trans_commit_list_add_tail(ctx->net, trans);
+
 	return trans;
 }
 
@@ -338,14 +447,13 @@
 	if (IS_ERR(trans))
 		return PTR_ERR(trans);
 
-	ctx->table->use--;
+	nft_use_dec(&ctx->table->use);
 	nft_deactivate_next(ctx->net, ctx->chain);
 
 	return 0;
 }
 
-static void nft_rule_expr_activate(const struct nft_ctx *ctx,
-				   struct nft_rule *rule)
+void nft_rule_expr_activate(const struct nft_ctx *ctx, struct nft_rule *rule)
 {
 	struct nft_expr *expr;
 
@@ -358,9 +466,8 @@
 	}
 }
 
-static void nft_rule_expr_deactivate(const struct nft_ctx *ctx,
-				     struct nft_rule *rule,
-				     enum nft_trans_phase phase)
+void nft_rule_expr_deactivate(const struct nft_ctx *ctx, struct nft_rule *rule,
+			      enum nft_trans_phase phase)
 {
 	struct nft_expr *expr;
 
@@ -379,7 +486,7 @@
 	/* You cannot delete the same rule twice */
 	if (nft_is_active_next(ctx->net, rule)) {
 		nft_deactivate_next(ctx->net, rule);
-		ctx->chain->use--;
+		nft_use_dec(&ctx->chain->use);
 		return 0;
 	}
 	return -ENOENT;
@@ -450,8 +557,9 @@
 	return 0;
 }
 
-static int nft_trans_set_add(const struct nft_ctx *ctx, int msg_type,
-			     struct nft_set *set)
+static int __nft_trans_set_add(const struct nft_ctx *ctx, int msg_type,
+			       struct nft_set *set,
+			       const struct nft_set_desc *desc)
 {
 	struct nft_trans *trans;
 
@@ -459,17 +567,84 @@
 	if (trans == NULL)
 		return -ENOMEM;
 
-	if (msg_type == NFT_MSG_NEWSET && ctx->nla[NFTA_SET_ID] != NULL) {
+	if (msg_type == NFT_MSG_NEWSET && ctx->nla[NFTA_SET_ID] && !desc) {
 		nft_trans_set_id(trans) =
 			ntohl(nla_get_be32(ctx->nla[NFTA_SET_ID]));
 		nft_activate_next(ctx->net, set);
 	}
 	nft_trans_set(trans) = set;
+	if (desc) {
+		nft_trans_set_update(trans) = true;
+		nft_trans_set_gc_int(trans) = desc->gc_int;
+		nft_trans_set_timeout(trans) = desc->timeout;
+	}
 	nft_trans_commit_list_add_tail(ctx->net, trans);
 
 	return 0;
 }
 
+static int nft_trans_set_add(const struct nft_ctx *ctx, int msg_type,
+			     struct nft_set *set)
+{
+	return __nft_trans_set_add(ctx, msg_type, set, NULL);
+}
+
+static int nft_mapelem_deactivate(const struct nft_ctx *ctx,
+				  struct nft_set *set,
+				  const struct nft_set_iter *iter,
+				  struct nft_set_elem *elem)
+{
+	struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
+
+	if (!nft_set_elem_active(ext, iter->genmask))
+		return 0;
+
+	nft_set_elem_change_active(ctx->net, set, ext);
+	nft_setelem_data_deactivate(ctx->net, set, elem);
+
+	return 0;
+}
+
+struct nft_set_elem_catchall {
+	struct list_head	list;
+	struct rcu_head		rcu;
+	void			*elem;
+};
+
+static void nft_map_catchall_deactivate(const struct nft_ctx *ctx,
+					struct nft_set *set)
+{
+	u8 genmask = nft_genmask_next(ctx->net);
+	struct nft_set_elem_catchall *catchall;
+	struct nft_set_elem elem;
+	struct nft_set_ext *ext;
+
+	list_for_each_entry(catchall, &set->catchall_list, list) {
+		ext = nft_set_elem_ext(set, catchall->elem);
+		if (!nft_set_elem_active(ext, genmask))
+			continue;
+
+		elem.priv = catchall->elem;
+		nft_set_elem_change_active(ctx->net, set, ext);
+		nft_setelem_data_deactivate(ctx->net, set, &elem);
+		break;
+	}
+}
+
+static void nft_map_deactivate(const struct nft_ctx *ctx, struct nft_set *set)
+{
+	struct nft_set_iter iter = {
+		.genmask	= nft_genmask_next(ctx->net),
+		.type		= NFT_ITER_UPDATE,
+		.fn		= nft_mapelem_deactivate,
+	};
+
+	set->ops->walk(ctx, set, &iter);
+	WARN_ON_ONCE(iter.err);
+
+	nft_map_catchall_deactivate(ctx, set);
+}
+
 static int nft_delset(const struct nft_ctx *ctx, struct nft_set *set)
 {
 	int err;
@@ -478,8 +653,11 @@
 	if (err < 0)
 		return err;
 
+	if (set->flags & (NFT_SET_MAP | NFT_SET_OBJECT))
+		nft_map_deactivate(ctx, set);
+
 	nft_deactivate_next(ctx->net, set);
-	ctx->table->use--;
+	nft_use_dec(&ctx->table->use);
 
 	return err;
 }
@@ -511,7 +689,7 @@
 		return err;
 
 	nft_deactivate_next(ctx->net, obj);
-	ctx->table->use--;
+	nft_use_dec(&ctx->table->use);
 
 	return err;
 }
@@ -529,6 +707,7 @@
 	if (msg_type == NFT_MSG_NEWFLOWTABLE)
 		nft_activate_next(ctx->net, flowtable);
 
+	INIT_LIST_HEAD(&nft_trans_flowtable_hooks(trans));
 	nft_trans_flowtable(trans) = flowtable;
 	nft_trans_commit_list_add_tail(ctx->net, trans);
 
@@ -545,7 +724,7 @@
 		return err;
 
 	nft_deactivate_next(ctx->net, flowtable);
-	ctx->table->use--;
+	nft_use_dec(&ctx->table->use);
 
 	return err;
 }
@@ -583,7 +762,7 @@
 
 static struct nft_table *nft_table_lookup_byhandle(const struct net *net,
 						   const struct nlattr *nla,
-						   u8 genmask, u32 nlpid)
+						   int family, u8 genmask, u32 nlpid)
 {
 	struct nftables_pernet *nft_net;
 	struct nft_table *table;
@@ -591,6 +770,7 @@
 	nft_net = nft_pernet(net);
 	list_for_each_entry(table, &nft_net->tables, list) {
 		if (be64_to_cpu(nla_get_be64(nla)) == table->handle &&
+		    table->family == family &&
 		    nft_active_genmask(table, genmask)) {
 			if (nft_table_has_owner(table) &&
 			    nlpid && table->nlpid != nlpid)
@@ -820,7 +1000,7 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
-	cb->seq = nft_net->base_seq;
+	cb->seq = READ_ONCE(nft_net->base_seq);
 
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (family != NFPROTO_UNSPEC && family != table->family)
@@ -967,6 +1147,24 @@
 #define __NFT_TABLE_F_UPDATE		(__NFT_TABLE_F_WAS_DORMANT | \
 					 __NFT_TABLE_F_WAS_AWAKEN)
 
+static bool nft_table_pending_update(const struct nft_ctx *ctx)
+{
+	struct nftables_pernet *nft_net = nft_pernet(ctx->net);
+	struct nft_trans *trans;
+
+	if (ctx->table->flags & __NFT_TABLE_F_UPDATE)
+		return true;
+
+	list_for_each_entry(trans, &nft_net->commit_list, list) {
+		if (trans->ctx.table == ctx->table &&
+		    trans->msg_type == NFT_MSG_DELCHAIN &&
+		    nft_is_base_chain(trans->ctx.chain))
+			return true;
+	}
+
+	return false;
+}
+
 static int nf_tables_updtable(struct nft_ctx *ctx)
 {
 	struct nft_trans *trans;
@@ -980,7 +1178,7 @@
 	if (flags & ~NFT_TABLE_F_MASK)
 		return -EOPNOTSUPP;
 
-	if (flags == ctx->table->flags)
+	if (flags == (ctx->table->flags & NFT_TABLE_F_MASK))
 		return 0;
 
 	if ((nft_table_has_owner(ctx->table) &&
@@ -989,6 +1187,10 @@
 	     flags & NFT_TABLE_F_OWNER))
 		return -EOPNOTSUPP;
 
+	/* No dormant off/on/off/on games in single transaction */
+	if (nft_table_pending_update(ctx))
+		return -EINVAL;
+
 	trans = nft_trans_alloc(ctx, NFT_MSG_NEWTABLE,
 				sizeof(struct nft_trans_table));
 	if (trans == NULL)
@@ -1017,6 +1219,7 @@
 	return 0;
 
 err_register_hooks:
+	ctx->table->flags |= NFT_TABLE_F_DORMANT;
 	nft_trans_destroy(trans);
 	return ret;
 }
@@ -1072,6 +1275,30 @@
 	return strcmp(obj->key.name, k->name);
 }
 
+static bool nft_supported_family(u8 family)
+{
+	return false
+#ifdef CONFIG_NF_TABLES_INET
+		|| family == NFPROTO_INET
+#endif
+#ifdef CONFIG_NF_TABLES_IPV4
+		|| family == NFPROTO_IPV4
+#endif
+#ifdef CONFIG_NF_TABLES_ARP
+		|| family == NFPROTO_ARP
+#endif
+#ifdef CONFIG_NF_TABLES_NETDEV
+		|| family == NFPROTO_NETDEV
+#endif
+#if IS_ENABLED(CONFIG_NF_TABLES_BRIDGE)
+		|| family == NFPROTO_BRIDGE
+#endif
+#ifdef CONFIG_NF_TABLES_IPV6
+		|| family == NFPROTO_IPV6
+#endif
+		;
+}
+
 static int nf_tables_newtable(struct sk_buff *skb, const struct nfnl_info *info,
 			      const struct nlattr * const nla[])
 {
@@ -1086,6 +1313,9 @@
 	u32 flags = 0;
 	int err;
 
+	if (!nft_supported_family(family))
+		return -EOPNOTSUPP;
+
 	lockdep_assert_held(&nft_net->commit_mutex);
 	attr = nla[NFTA_TABLE_NAME];
 	table = nft_table_lookup(net, attr, family, genmask,
@@ -1139,7 +1369,7 @@
 	INIT_LIST_HEAD(&table->flowtables);
 	table->family = family;
 	table->flags = flags;
-	table->handle = ++table_handle;
+	table->handle = ++nft_net->table_handle;
 	if (table->flags & NFT_TABLE_F_OWNER)
 		table->nlpid = NETLINK_CB(skb).portid;
 
@@ -1174,7 +1404,7 @@
 		if (!nft_is_active_next(ctx->net, chain))
 			continue;
 
-		if (nft_chain_is_bound(chain))
+		if (nft_chain_binding(chain))
 			continue;
 
 		ctx->chain = chain;
@@ -1188,8 +1418,7 @@
 		if (!nft_is_active_next(ctx->net, set))
 			continue;
 
-		if (nft_set_is_anonymous(set) &&
-		    !list_empty(&set->bindings))
+		if (nft_set_is_anonymous(set))
 			continue;
 
 		err = nft_delset(ctx, set);
@@ -1219,7 +1448,7 @@
 		if (!nft_is_active_next(ctx->net, chain))
 			continue;
 
-		if (nft_chain_is_bound(chain))
+		if (nft_chain_binding(chain))
 			continue;
 
 		ctx->chain = chain;
@@ -1285,7 +1514,7 @@
 
 	if (nla[NFTA_TABLE_HANDLE]) {
 		attr = nla[NFTA_TABLE_HANDLE];
-		table = nft_table_lookup_byhandle(net, attr, genmask,
+		table = nft_table_lookup_byhandle(net, attr, family, genmask,
 						  NETLINK_CB(skb).portid);
 	} else {
 		attr = nla[NFTA_TABLE_NAME];
@@ -1609,7 +1838,7 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
-	cb->seq = nft_net->base_seq;
+	cb->seq = READ_ONCE(nft_net->base_seq);
 
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (family != NFPROTO_UNSPEC && family != table->family)
@@ -1820,7 +2049,6 @@
 		goto err_hook_dev;
 	}
 	hook->ops.dev = dev;
-	hook->inactive = false;
 
 	return hook;
 
@@ -2057,15 +2285,17 @@
 	chain->flags |= NFT_CHAIN_BASE | flags;
 	basechain->policy = NF_ACCEPT;
 	if (chain->flags & NFT_CHAIN_HW_OFFLOAD &&
-	    nft_chain_offload_priority(basechain) < 0)
+	    !nft_chain_offload_support(basechain)) {
+		list_splice_init(&basechain->hook_list, &hook->list);
 		return -EOPNOTSUPP;
+	}
 
 	flow_block_init(&basechain->flow_block);
 
 	return 0;
 }
 
-static int nft_chain_add(struct nft_table *table, struct nft_chain *chain)
+int nft_chain_add(struct nft_table *table, struct nft_chain *chain)
 {
 	int err;
 
@@ -2088,7 +2318,6 @@
 	const struct nlattr * const *nla = ctx->nla;
 	struct nft_table *table = ctx->table;
 	struct nft_base_chain *basechain;
-	struct nft_stats __percpu *stats;
 	struct net *net = ctx->net;
 	char name[NFT_NAME_MAXLEN];
 	struct nft_trans *trans;
@@ -2096,12 +2325,13 @@
 	struct nft_rule **rules;
 	int err;
 
-	if (table->use == UINT_MAX)
-		return -EOVERFLOW;
-
 	if (nla[NFTA_CHAIN_HOOK]) {
+		struct nft_stats __percpu *stats = NULL;
 		struct nft_chain_hook hook;
 
+		if (table->flags & __NFT_TABLE_F_UPDATE)
+			return -EINVAL;
+
 		if (flags & NFT_CHAIN_BINDING)
 			return -EOPNOTSUPP;
 
@@ -2125,15 +2355,17 @@
 				return PTR_ERR(stats);
 			}
 			rcu_assign_pointer(basechain->stats, stats);
-			static_branch_inc(&nft_counters_enabled);
 		}
 
 		err = nft_basechain_init(basechain, family, &hook, flags);
 		if (err < 0) {
 			nft_chain_release_hook(&hook);
 			kfree(basechain);
+			free_percpu(stats);
 			return err;
 		}
+		if (stats)
+			static_branch_inc(&nft_counters_enabled);
 	} else {
 		if (flags & NFT_CHAIN_BASE)
 			return -EINVAL;
@@ -2192,6 +2424,11 @@
 	if (err < 0)
 		goto err_destroy_chain;
 
+	if (!nft_use_inc(&table->use)) {
+		err = -EMFILE;
+		goto err_use;
+	}
+
 	trans = nft_trans_chain_add(ctx, NFT_MSG_NEWCHAIN);
 	if (IS_ERR(trans)) {
 		err = PTR_ERR(trans);
@@ -2208,10 +2445,11 @@
 		goto err_unregister_hook;
 	}
 
-	table->use++;
-
 	return 0;
+
 err_unregister_hook:
+	nft_use_dec_restore(&table->use);
+err_use:
 	nf_tables_unregister_hook(net, table, chain);
 err_destroy_chain:
 	nf_tables_chain_destroy(ctx);
@@ -2362,7 +2600,8 @@
 }
 
 static struct nft_chain *nft_chain_lookup_byid(const struct net *net,
-					       const struct nlattr *nla)
+					       const struct nft_table *table,
+					       const struct nlattr *nla, u8 genmask)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
 	u32 id = ntohl(nla_get_be32(nla));
@@ -2372,7 +2611,9 @@
 		struct nft_chain *chain = trans->ctx.chain;
 
 		if (trans->msg_type == NFT_MSG_NEWCHAIN &&
-		    id == nft_trans_chain_id(trans))
+		    chain->table == table &&
+		    id == nft_trans_chain_id(trans) &&
+		    nft_active_genmask(chain, genmask))
 			return chain;
 	}
 	return ERR_PTR(-ENOENT);
@@ -2461,6 +2702,9 @@
 	nft_ctx_init(&ctx, net, skb, info->nlh, family, table, chain, nla);
 
 	if (chain != NULL) {
+		if (chain->flags & NFT_CHAIN_BINDING)
+			return -EINVAL;
+
 		if (info->nlh->nlmsg_flags & NLM_F_EXCL) {
 			NL_SET_BAD_ATTR(extack, attr);
 			return -EEXIST;
@@ -2512,6 +2756,9 @@
 		return PTR_ERR(chain);
 	}
 
+	if (nft_chain_binding(chain))
+		return -EOPNOTSUPP;
+
 	if (info->nlh->nlmsg_flags & NLM_F_NONREC &&
 	    chain->use > 0)
 		return -EBUSY;
@@ -2582,7 +2829,7 @@
 {
 	const struct nft_expr_type *type, *candidate = NULL;
 
-	list_for_each_entry(type, &nf_tables_expressions, list) {
+	list_for_each_entry_rcu(type, &nf_tables_expressions, list) {
 		if (!nla_strcmp(nla, type->name)) {
 			if (!type->family && !candidate)
 				candidate = type;
@@ -2614,9 +2861,13 @@
 	if (nla == NULL)
 		return ERR_PTR(-EINVAL);
 
+	rcu_read_lock();
 	type = __nft_expr_type_get(family, nla);
-	if (type != NULL && try_module_get(type->owner))
+	if (type != NULL && try_module_get(type->owner)) {
+		rcu_read_unlock();
 		return type;
+	}
+	rcu_read_unlock();
 
 	lockdep_nfnl_nft_mutex_not_held();
 #ifdef CONFIG_MODULES
@@ -2778,42 +3029,45 @@
 
 	err = nf_tables_expr_parse(ctx, nla, &expr_info);
 	if (err < 0)
-		goto err1;
+		goto err_expr_parse;
+
+	err = -EOPNOTSUPP;
+	if (!(expr_info.ops->type->flags & NFT_EXPR_STATEFUL))
+		goto err_expr_stateful;
 
 	err = -ENOMEM;
 	expr = kzalloc(expr_info.ops->size, GFP_KERNEL);
 	if (expr == NULL)
-		goto err2;
+		goto err_expr_stateful;
 
 	err = nf_tables_newexpr(ctx, &expr_info, expr);
 	if (err < 0)
-		goto err3;
+		goto err_expr_new;
 
 	return expr;
-err3:
+err_expr_new:
 	kfree(expr);
-err2:
+err_expr_stateful:
 	owner = expr_info.ops->type->owner;
 	if (expr_info.ops->type->release_ops)
 		expr_info.ops->type->release_ops(expr_info.ops);
 
 	module_put(owner);
-err1:
+err_expr_parse:
 	return ERR_PTR(err);
 }
 
-int nft_expr_clone(struct nft_expr *dst, struct nft_expr *src)
+int nft_expr_clone(struct nft_expr *dst, struct nft_expr *src, gfp_t gfp)
 {
 	int err;
 
-	if (src->ops->clone) {
-		dst->ops = src->ops;
-		err = src->ops->clone(dst, src);
-		if (err < 0)
-			return err;
-	} else {
-		memcpy(dst, src, src->ops->size);
-	}
+	if (WARN_ON_ONCE(!src->ops->clone))
+		return -EINVAL;
+
+	dst->ops = src->ops;
+	err = src->ops->clone(dst, src, gfp);
+	if (err < 0)
+		return err;
 
 	__module_get(src->ops->type->owner);
 
@@ -2992,10 +3246,6 @@
 			goto cont_skip;
 		if (*idx < s_idx)
 			goto cont;
-		if (*idx > s_idx) {
-			memset(&cb->args[1], 0,
-					sizeof(cb->args) - sizeof(cb->args[0]));
-		}
 		if (prule)
 			handle = prule->handle;
 		else
@@ -3032,7 +3282,7 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
-	cb->seq = nft_net->base_seq;
+	cb->seq = READ_ONCE(nft_net->base_seq);
 
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (family != NFPROTO_UNSPEC && family != table->family)
@@ -3180,8 +3430,7 @@
 	return err;
 }
 
-static void nf_tables_rule_destroy(const struct nft_ctx *ctx,
-				   struct nft_rule *rule)
+void nf_tables_rule_destroy(const struct nft_ctx *ctx, struct nft_rule *rule)
 {
 	struct nft_expr *expr, *next;
 
@@ -3198,12 +3447,21 @@
 	kfree(rule);
 }
 
-void nf_tables_rule_release(const struct nft_ctx *ctx, struct nft_rule *rule)
+static void nf_tables_rule_release(const struct nft_ctx *ctx, struct nft_rule *rule)
 {
 	nft_rule_expr_deactivate(ctx, rule, NFT_TRANS_RELEASE);
 	nf_tables_rule_destroy(ctx, rule);
 }
 
+/** nft_chain_validate - loop detection and hook validation
+ *
+ * @ctx: context containing call depth and base chain
+ * @chain: chain to validate
+ *
+ * Walk through the rules of the given chain and chase all jumps/gotos
+ * and set lookups until either the jump limit is hit or all reachable
+ * chains have been validated.
+ */
 int nft_chain_validate(const struct nft_ctx *ctx, const struct nft_chain *chain)
 {
 	struct nft_expr *expr, *last;
@@ -3222,6 +3480,9 @@
 			if (!expr->ops->validate)
 				continue;
 
+			/* This may call nft_chain_validate() recursively,
+			 * callers that do so must increment ctx->level.
+			 */
 			err = expr->ops->validate(ctx, expr, &data);
 			if (err < 0)
 				return err;
@@ -3249,12 +3510,72 @@
 		err = nft_chain_validate(&ctx, chain);
 		if (err < 0)
 			return err;
+
+		cond_resched();
+	}
+
+	return 0;
+}
+
+int nft_setelem_validate(const struct nft_ctx *ctx, struct nft_set *set,
+			 const struct nft_set_iter *iter,
+			 struct nft_set_elem *elem)
+{
+	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
+	struct nft_ctx *pctx = (struct nft_ctx *)ctx;
+	const struct nft_data *data;
+	int err;
+
+	if (!nft_set_elem_active(ext, iter->genmask))
+		return 0;
+
+	if (nft_set_ext_exists(ext, NFT_SET_EXT_FLAGS) &&
+	    *nft_set_ext_flags(ext) & NFT_SET_ELEM_INTERVAL_END)
+		return 0;
+
+	data = nft_set_ext_data(ext);
+	switch (data->verdict.code) {
+	case NFT_JUMP:
+	case NFT_GOTO:
+		pctx->level++;
+		err = nft_chain_validate(ctx, data->verdict.chain);
+		if (err < 0)
+			return err;
+		pctx->level--;
+		break;
+	default:
+		break;
 	}
 
 	return 0;
 }
 
+int nft_set_catchall_validate(const struct nft_ctx *ctx, struct nft_set *set)
+{
+	struct nft_set_iter dummy_iter = {
+		.genmask	= nft_genmask_next(ctx->net),
+	};
+	struct nft_set_elem_catchall *catchall;
+	struct nft_set_elem elem;
+	struct nft_set_ext *ext;
+	int ret = 0;
+
+	list_for_each_entry_rcu(catchall, &set->catchall_list, list) {
+		ext = nft_set_elem_ext(set, catchall->elem);
+		if (!nft_set_elem_active(ext, dummy_iter.genmask))
+			continue;
+
+		elem.priv = catchall->elem;
+		ret = nft_setelem_validate(ctx, set, &dummy_iter, &elem);
+		if (ret < 0)
+			return ret;
+	}
+
+	return ret;
+}
+
 static struct nft_rule *nft_rule_lookup_byid(const struct net *net,
+					     const struct nft_chain *chain,
 					     const struct nlattr *nla);
 
 #define NFT_RULE_MAXEXPRS	128
@@ -3297,11 +3618,10 @@
 			NL_SET_BAD_ATTR(extack, nla[NFTA_RULE_CHAIN]);
 			return PTR_ERR(chain);
 		}
-		if (nft_chain_is_bound(chain))
-			return -EOPNOTSUPP;
 
 	} else if (nla[NFTA_RULE_CHAIN_ID]) {
-		chain = nft_chain_lookup_byid(net, nla[NFTA_RULE_CHAIN_ID]);
+		chain = nft_chain_lookup_byid(net, table, nla[NFTA_RULE_CHAIN_ID],
+					      genmask);
 		if (IS_ERR(chain)) {
 			NL_SET_BAD_ATTR(extack, nla[NFTA_RULE_CHAIN_ID]);
 			return PTR_ERR(chain);
@@ -3310,6 +3630,9 @@
 		return -EINVAL;
 	}
 
+	if (nft_chain_is_bound(chain))
+		return -EOPNOTSUPP;
+
 	if (nla[NFTA_RULE_HANDLE]) {
 		handle = be64_to_cpu(nla_get_be64(nla[NFTA_RULE_HANDLE]));
 		rule = __nft_rule_lookup(chain, handle);
@@ -3332,9 +3655,6 @@
 			return -EINVAL;
 		handle = nf_tables_alloc_handle(table);
 
-		if (chain->use == UINT_MAX)
-			return -EOVERFLOW;
-
 		if (nla[NFTA_RULE_POSITION]) {
 			pos_handle = be64_to_cpu(nla_get_be64(nla[NFTA_RULE_POSITION]));
 			old_rule = __nft_rule_lookup(chain, pos_handle);
@@ -3343,7 +3663,7 @@
 				return PTR_ERR(old_rule);
 			}
 		} else if (nla[NFTA_RULE_POSITION_ID]) {
-			old_rule = nft_rule_lookup_byid(net, nla[NFTA_RULE_POSITION_ID]);
+			old_rule = nft_rule_lookup_byid(net, chain, nla[NFTA_RULE_POSITION_ID]);
 			if (IS_ERR(old_rule)) {
 				NL_SET_BAD_ATTR(extack, nla[NFTA_RULE_POSITION_ID]);
 				return PTR_ERR(old_rule);
@@ -3428,7 +3748,17 @@
 		}
 	}
 
+	if (!nft_use_inc(&chain->use)) {
+		err = -EMFILE;
+		goto err_release_rule;
+	}
+
 	if (info->nlh->nlmsg_flags & NLM_F_REPLACE) {
+		if (nft_chain_binding(chain)) {
+			err = -EOPNOTSUPP;
+			goto err_destroy_flow_rule;
+		}
+
 		err = nft_delrule(&ctx, old_rule);
 		if (err < 0)
 			goto err_destroy_flow_rule;
@@ -3459,7 +3789,6 @@
 		}
 	}
 	kvfree(expr_info);
-	chain->use++;
 
 	if (flow)
 		nft_trans_flow_rule(trans) = flow;
@@ -3470,10 +3799,12 @@
 	return 0;
 
 err_destroy_flow_rule:
+	nft_use_dec_restore(&chain->use);
 	if (flow)
 		nft_flow_rule_destroy(flow);
 err_release_rule:
-	nf_tables_rule_release(&ctx, rule);
+	nft_rule_expr_deactivate(&ctx, rule, NFT_TRANS_PREPARE_ERROR);
+	nf_tables_rule_destroy(&ctx, rule);
 err_release_expr:
 	for (i = 0; i < n; i++) {
 		if (expr_info[i].ops) {
@@ -3488,6 +3819,7 @@
 }
 
 static struct nft_rule *nft_rule_lookup_byid(const struct net *net,
+					     const struct nft_chain *chain,
 					     const struct nlattr *nla)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
@@ -3495,11 +3827,10 @@
 	struct nft_trans *trans;
 
 	list_for_each_entry(trans, &nft_net->commit_list, list) {
-		struct nft_rule *rule = nft_trans_rule(trans);
-
 		if (trans->msg_type == NFT_MSG_NEWRULE &&
+		    trans->ctx.chain == chain &&
 		    id == nft_trans_rule_id(trans))
-			return rule;
+			return nft_trans_rule(trans);
 	}
 	return ERR_PTR(-ENOENT);
 }
@@ -3531,7 +3862,7 @@
 			NL_SET_BAD_ATTR(extack, nla[NFTA_RULE_CHAIN]);
 			return PTR_ERR(chain);
 		}
-		if (nft_chain_is_bound(chain))
+		if (nft_chain_binding(chain))
 			return -EOPNOTSUPP;
 	}
 
@@ -3547,7 +3878,7 @@
 
 			err = nft_delrule(&ctx, rule);
 		} else if (nla[NFTA_RULE_ID]) {
-			rule = nft_rule_lookup_byid(net, nla[NFTA_RULE_ID]);
+			rule = nft_rule_lookup_byid(net, chain, nla[NFTA_RULE_ID]);
 			if (IS_ERR(rule)) {
 				NL_SET_BAD_ATTR(extack, nla[NFTA_RULE_ID]);
 				return PTR_ERR(rule);
@@ -3561,6 +3892,8 @@
 		list_for_each_entry(chain, &table->chains, list) {
 			if (!nft_is_active_next(net, chain))
 				continue;
+			if (nft_chain_binding(chain))
+				continue;
 
 			ctx.chain = chain;
 			err = nft_delrule_by_chain(&ctx);
@@ -3604,8 +3937,7 @@
 static const struct nft_set_ops *
 nft_select_set_ops(const struct nft_ctx *ctx,
 		   const struct nlattr * const nla[],
-		   const struct nft_set_desc *desc,
-		   enum nft_set_policies policy)
+		   const struct nft_set_desc *desc)
 {
 	struct nftables_pernet *nft_net = nft_pernet(ctx->net);
 	const struct nft_set_ops *ops, *bops;
@@ -3634,7 +3966,7 @@
 		if (!ops->estimate(desc, flags, &est))
 			continue;
 
-		switch (policy) {
+		switch (desc->policy) {
 		case NFT_SET_POL_PERFORMANCE:
 			if (est.lookup < best.lookup)
 				break;
@@ -3726,6 +4058,7 @@
 }
 
 static struct nft_set *nft_set_lookup_byid(const struct net *net,
+					   const struct nft_table *table,
 					   const struct nlattr *nla, u8 genmask)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
@@ -3737,6 +4070,7 @@
 			struct nft_set *set = nft_trans_set(trans);
 
 			if (id == nft_trans_set_id(trans) &&
+			    set->table == table &&
 			    nft_active_genmask(set, genmask))
 				return set;
 		}
@@ -3757,7 +4091,7 @@
 		if (!nla_set_id)
 			return set;
 
-		set = nft_set_lookup_byid(net, nla_set_id, genmask);
+		set = nft_set_lookup_byid(net, table, nla_set_id, genmask);
 	}
 	return set;
 }
@@ -3776,6 +4110,9 @@
 		if (p[1] != 'd' || strchr(p + 2, '%'))
 			return -EINVAL;
 
+		if (strnlen(name, NFT_SET_MAX_ANONLEN) >= NFT_SET_MAX_ANONLEN)
+			return -EINVAL;
+
 		inuse = (unsigned long *)get_zeroed_page(GFP_KERNEL);
 		if (inuse == NULL)
 			return -ENOMEM;
@@ -3783,7 +4120,7 @@
 		list_for_each_entry(i, &ctx->table->sets, list) {
 			int tmp;
 
-			if (!nft_is_active_next(ctx->net, set))
+			if (!nft_is_active_next(ctx->net, i))
 				continue;
 			if (!sscanf(i->name, name, &tmp))
 				continue;
@@ -3828,7 +4165,7 @@
 		return -ERANGE;
 
 	ms *= NSEC_PER_MSEC;
-	*result = nsecs_to_jiffies64(ms);
+	*result = nsecs_to_jiffies64(ms) ? : !!ms;
 	return 0;
 }
 
@@ -3867,8 +4204,10 @@
 static int nf_tables_fill_set(struct sk_buff *skb, const struct nft_ctx *ctx,
 			      const struct nft_set *set, u16 event, u16 flags)
 {
-	struct nlmsghdr *nlh;
+	u64 timeout = READ_ONCE(set->timeout);
+	u32 gc_int = READ_ONCE(set->gc_int);
 	u32 portid = ctx->portid;
+	struct nlmsghdr *nlh;
 	struct nlattr *nest;
 	u32 seq = ctx->seq;
 	int i;
@@ -3904,13 +4243,13 @@
 	    nla_put_be32(skb, NFTA_SET_OBJ_TYPE, htonl(set->objtype)))
 		goto nla_put_failure;
 
-	if (set->timeout &&
+	if (timeout &&
 	    nla_put_be64(skb, NFTA_SET_TIMEOUT,
-			 nf_jiffies64_to_msecs(set->timeout),
+			 nf_jiffies64_to_msecs(timeout),
 			 NFTA_SET_PAD))
 		goto nla_put_failure;
-	if (set->gc_int &&
-	    nla_put_be32(skb, NFTA_SET_GC_INTERVAL, htonl(set->gc_int)))
+	if (gc_int &&
+	    nla_put_be32(skb, NFTA_SET_GC_INTERVAL, htonl(gc_int)))
 		goto nla_put_failure;
 
 	if (set->policy != NFT_SET_POL_PERFORMANCE) {
@@ -4009,7 +4348,7 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
-	cb->seq = nft_net->base_seq;
+	cb->seq = READ_ONCE(nft_net->base_seq);
 
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (ctx->family != NFPROTO_UNSPEC &&
@@ -4147,6 +4486,9 @@
 	u32 len;
 	int err;
 
+	if (desc->field_count >= ARRAY_SIZE(desc->field_len))
+		return -E2BIG;
+
 	err = nla_parse_nested_deprecated(tb, NFTA_SET_FIELD_MAX, attr,
 					  nft_concat_policy, NULL);
 	if (err < 0)
@@ -4156,9 +4498,8 @@
 		return -EINVAL;
 
 	len = ntohl(nla_get_be32(tb[NFTA_SET_FIELD_LEN]));
-
-	if (len * BITS_PER_BYTE / 32 > NFT_REG32_COUNT)
-		return -E2BIG;
+	if (!len || len > U8_MAX)
+		return -EINVAL;
 
 	desc->field_len[desc->field_count++] = len;
 
@@ -4168,8 +4509,9 @@
 static int nft_set_desc_concat(struct nft_set_desc *desc,
 			       const struct nlattr *nla)
 {
+	u32 len = 0, num_regs;
 	struct nlattr *attr;
-	int rem, err;
+	int rem, err, i;
 
 	nla_for_each_nested(attr, nla, rem) {
 		if (nla_type(attr) != NFTA_LIST_ELEM)
@@ -4180,6 +4522,16 @@
 			return err;
 	}
 
+	for (i = 0; i < desc->field_count; i++)
+		len += round_up(desc->field_len[i], sizeof(u32));
+
+	if (len != desc->klen)
+		return -EINVAL;
+
+	num_regs = DIV_ROUND_UP(desc->klen, sizeof(u32));
+	if (num_regs > NFT_REG32_COUNT)
+		return -E2BIG;
+
 	return 0;
 }
 
@@ -4202,15 +4554,94 @@
 	return err;
 }
 
+static int nft_set_expr_alloc(struct nft_ctx *ctx, struct nft_set *set,
+			      const struct nlattr * const *nla,
+			      struct nft_expr **exprs, int *num_exprs,
+			      u32 flags)
+{
+	struct nft_expr *expr;
+	int err, i;
+
+	if (nla[NFTA_SET_EXPR]) {
+		expr = nft_set_elem_expr_alloc(ctx, set, nla[NFTA_SET_EXPR]);
+		if (IS_ERR(expr)) {
+			err = PTR_ERR(expr);
+			goto err_set_expr_alloc;
+		}
+		exprs[0] = expr;
+		(*num_exprs)++;
+	} else if (nla[NFTA_SET_EXPRESSIONS]) {
+		struct nlattr *tmp;
+		int left;
+
+		if (!(flags & NFT_SET_EXPR)) {
+			err = -EINVAL;
+			goto err_set_expr_alloc;
+		}
+		i = 0;
+		nla_for_each_nested(tmp, nla[NFTA_SET_EXPRESSIONS], left) {
+			if (i == NFT_SET_EXPR_MAX) {
+				err = -E2BIG;
+				goto err_set_expr_alloc;
+			}
+			if (nla_type(tmp) != NFTA_LIST_ELEM) {
+				err = -EINVAL;
+				goto err_set_expr_alloc;
+			}
+			expr = nft_set_elem_expr_alloc(ctx, set, tmp);
+			if (IS_ERR(expr)) {
+				err = PTR_ERR(expr);
+				goto err_set_expr_alloc;
+			}
+			exprs[i++] = expr;
+			(*num_exprs)++;
+		}
+	}
+
+	return 0;
+
+err_set_expr_alloc:
+	for (i = 0; i < *num_exprs; i++)
+		nft_expr_destroy(ctx, exprs[i]);
+
+	return err;
+}
+
+static bool nft_set_is_same(const struct nft_set *set,
+			    const struct nft_set_desc *desc,
+			    struct nft_expr *exprs[], u32 num_exprs, u32 flags)
+{
+	int i;
+
+	if (set->ktype != desc->ktype ||
+	    set->dtype != desc->dtype ||
+	    set->flags != flags ||
+	    set->klen != desc->klen ||
+	    set->dlen != desc->dlen ||
+	    set->field_count != desc->field_count ||
+	    set->num_exprs != num_exprs)
+		return false;
+
+	for (i = 0; i < desc->field_count; i++) {
+		if (set->field_len[i] != desc->field_len[i])
+			return false;
+	}
+
+	for (i = 0; i < num_exprs; i++) {
+		if (set->exprs[i]->ops != exprs[i]->ops)
+			return false;
+	}
+
+	return true;
+}
+
 static int nf_tables_newset(struct sk_buff *skb, const struct nfnl_info *info,
 			    const struct nlattr * const nla[])
 {
-	u32 ktype, dtype, flags, policy, gc_int, objtype;
 	struct netlink_ext_ack *extack = info->extack;
 	u8 genmask = nft_genmask_next(info->net);
 	u8 family = info->nfmsg->nfgen_family;
 	const struct nft_set_ops *ops;
-	struct nft_expr *expr = NULL;
 	struct net *net = info->net;
 	struct nft_set_desc desc;
 	struct nft_table *table;
@@ -4218,10 +4649,11 @@
 	struct nft_set *set;
 	struct nft_ctx ctx;
 	size_t alloc_size;
-	u64 timeout;
+	int num_exprs = 0;
 	char *name;
 	int err, i;
 	u16 udlen;
+	u32 flags;
 	u64 size;
 
 	if (nla[NFTA_SET_TABLE] == NULL ||
@@ -4232,10 +4664,10 @@
 
 	memset(&desc, 0, sizeof(desc));
 
-	ktype = NFT_DATA_VALUE;
+	desc.ktype = NFT_DATA_VALUE;
 	if (nla[NFTA_SET_KEY_TYPE] != NULL) {
-		ktype = ntohl(nla_get_be32(nla[NFTA_SET_KEY_TYPE]));
-		if ((ktype & NFT_DATA_RESERVED_MASK) == NFT_DATA_RESERVED_MASK)
+		desc.ktype = ntohl(nla_get_be32(nla[NFTA_SET_KEY_TYPE]));
+		if ((desc.ktype & NFT_DATA_RESERVED_MASK) == NFT_DATA_RESERVED_MASK)
 			return -EINVAL;
 	}
 
@@ -4258,19 +4690,25 @@
 		if ((flags & (NFT_SET_EVAL | NFT_SET_OBJECT)) ==
 			     (NFT_SET_EVAL | NFT_SET_OBJECT))
 			return -EOPNOTSUPP;
+		if ((flags & (NFT_SET_ANONYMOUS | NFT_SET_TIMEOUT | NFT_SET_EVAL)) ==
+			     (NFT_SET_ANONYMOUS | NFT_SET_TIMEOUT))
+			return -EOPNOTSUPP;
+		if ((flags & (NFT_SET_CONSTANT | NFT_SET_TIMEOUT)) ==
+			     (NFT_SET_CONSTANT | NFT_SET_TIMEOUT))
+			return -EOPNOTSUPP;
 	}
 
-	dtype = 0;
+	desc.dtype = 0;
 	if (nla[NFTA_SET_DATA_TYPE] != NULL) {
 		if (!(flags & NFT_SET_MAP))
 			return -EINVAL;
 
-		dtype = ntohl(nla_get_be32(nla[NFTA_SET_DATA_TYPE]));
-		if ((dtype & NFT_DATA_RESERVED_MASK) == NFT_DATA_RESERVED_MASK &&
-		    dtype != NFT_DATA_VERDICT)
+		desc.dtype = ntohl(nla_get_be32(nla[NFTA_SET_DATA_TYPE]));
+		if ((desc.dtype & NFT_DATA_RESERVED_MASK) == NFT_DATA_RESERVED_MASK &&
+		    desc.dtype != NFT_DATA_VERDICT)
 			return -EINVAL;
 
-		if (dtype != NFT_DATA_VERDICT) {
+		if (desc.dtype != NFT_DATA_VERDICT) {
 			if (nla[NFTA_SET_DATA_LEN] == NULL)
 				return -EINVAL;
 			desc.dlen = ntohl(nla_get_be32(nla[NFTA_SET_DATA_LEN]));
@@ -4285,39 +4723,63 @@
 		if (!(flags & NFT_SET_OBJECT))
 			return -EINVAL;
 
-		objtype = ntohl(nla_get_be32(nla[NFTA_SET_OBJ_TYPE]));
-		if (objtype == NFT_OBJECT_UNSPEC ||
-		    objtype > NFT_OBJECT_MAX)
+		desc.objtype = ntohl(nla_get_be32(nla[NFTA_SET_OBJ_TYPE]));
+		if (desc.objtype == NFT_OBJECT_UNSPEC ||
+		    desc.objtype > NFT_OBJECT_MAX)
 			return -EOPNOTSUPP;
 	} else if (flags & NFT_SET_OBJECT)
 		return -EINVAL;
 	else
-		objtype = NFT_OBJECT_UNSPEC;
+		desc.objtype = NFT_OBJECT_UNSPEC;
 
-	timeout = 0;
+	desc.timeout = 0;
 	if (nla[NFTA_SET_TIMEOUT] != NULL) {
 		if (!(flags & NFT_SET_TIMEOUT))
 			return -EINVAL;
 
-		err = nf_msecs_to_jiffies64(nla[NFTA_SET_TIMEOUT], &timeout);
+		if (flags & NFT_SET_ANONYMOUS)
+			return -EOPNOTSUPP;
+
+		err = nf_msecs_to_jiffies64(nla[NFTA_SET_TIMEOUT], &desc.timeout);
 		if (err)
 			return err;
 	}
-	gc_int = 0;
+	desc.gc_int = 0;
 	if (nla[NFTA_SET_GC_INTERVAL] != NULL) {
 		if (!(flags & NFT_SET_TIMEOUT))
 			return -EINVAL;
-		gc_int = ntohl(nla_get_be32(nla[NFTA_SET_GC_INTERVAL]));
+
+		if (flags & NFT_SET_ANONYMOUS)
+			return -EOPNOTSUPP;
+
+		desc.gc_int = ntohl(nla_get_be32(nla[NFTA_SET_GC_INTERVAL]));
 	}
 
-	policy = NFT_SET_POL_PERFORMANCE;
-	if (nla[NFTA_SET_POLICY] != NULL)
-		policy = ntohl(nla_get_be32(nla[NFTA_SET_POLICY]));
+	desc.policy = NFT_SET_POL_PERFORMANCE;
+	if (nla[NFTA_SET_POLICY] != NULL) {
+		desc.policy = ntohl(nla_get_be32(nla[NFTA_SET_POLICY]));
+		switch (desc.policy) {
+		case NFT_SET_POL_PERFORMANCE:
+		case NFT_SET_POL_MEMORY:
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	}
 
 	if (nla[NFTA_SET_DESC] != NULL) {
 		err = nf_tables_set_desc_parse(&desc, nla[NFTA_SET_DESC]);
 		if (err < 0)
 			return err;
+
+		if (desc.field_count > 1) {
+			if (!(flags & NFT_SET_CONCAT))
+				return -EINVAL;
+		} else if (flags & NFT_SET_CONCAT) {
+			return -EINVAL;
+		}
+	} else if (flags & NFT_SET_CONCAT) {
+		return -EINVAL;
 	}
 
 	if (nla[NFTA_SET_EXPR] || nla[NFTA_SET_EXPRESSIONS])
@@ -4339,6 +4801,8 @@
 			return PTR_ERR(set);
 		}
 	} else {
+		struct nft_expr *exprs[NFT_SET_EXPR_MAX] = {};
+
 		if (info->nlh->nlmsg_flags & NLM_F_EXCL) {
 			NL_SET_BAD_ATTR(extack, nla[NFTA_SET_NAME]);
 			return -EEXIST;
@@ -4346,13 +4810,32 @@
 		if (info->nlh->nlmsg_flags & NLM_F_REPLACE)
 			return -EOPNOTSUPP;
 
-		return 0;
+		if (nft_set_is_anonymous(set))
+			return -EOPNOTSUPP;
+
+		err = nft_set_expr_alloc(&ctx, set, nla, exprs, &num_exprs, flags);
+		if (err < 0)
+			return err;
+
+		err = 0;
+		if (!nft_set_is_same(set, &desc, exprs, num_exprs, flags)) {
+			NL_SET_BAD_ATTR(extack, nla[NFTA_SET_NAME]);
+			err = -EEXIST;
+		}
+
+		for (i = 0; i < num_exprs; i++)
+			nft_expr_destroy(&ctx, exprs[i]);
+
+		if (err < 0)
+			return err;
+
+		return __nft_trans_set_add(&ctx, NFT_MSG_NEWSET, set, &desc);
 	}
 
 	if (!(info->nlh->nlmsg_flags & NLM_F_CREATE))
 		return -ENOENT;
 
-	ops = nft_select_set_ops(&ctx, nla, &desc, policy);
+	ops = nft_select_set_ops(&ctx, nla, &desc);
 	if (IS_ERR(ops))
 		return PTR_ERR(ops);
 
@@ -4366,9 +4849,15 @@
 	alloc_size = sizeof(*set) + size + udlen;
 	if (alloc_size < size || alloc_size > INT_MAX)
 		return -ENOMEM;
+
+	if (!nft_use_inc(&table->use))
+		return -EMFILE;
+
 	set = kvzalloc(alloc_size, GFP_KERNEL);
-	if (!set)
-		return -ENOMEM;
+	if (!set) {
+		err = -ENOMEM;
+		goto err_alloc;
+	}
 
 	name = nla_strdup(nla[NFTA_SET_NAME], GFP_KERNEL);
 	if (!name) {
@@ -4389,21 +4878,22 @@
 
 	INIT_LIST_HEAD(&set->bindings);
 	INIT_LIST_HEAD(&set->catchall_list);
+	refcount_set(&set->refs, 1);
 	set->table = table;
 	write_pnet(&set->net, net);
 	set->ops = ops;
-	set->ktype = ktype;
+	set->ktype = desc.ktype;
 	set->klen = desc.klen;
-	set->dtype = dtype;
-	set->objtype = objtype;
+	set->dtype = desc.dtype;
+	set->objtype = desc.objtype;
 	set->dlen = desc.dlen;
 	set->flags = flags;
 	set->size = desc.size;
-	set->policy = policy;
+	set->policy = desc.policy;
 	set->udlen = udlen;
 	set->udata = udata;
-	set->timeout = timeout;
-	set->gc_int = gc_int;
+	set->timeout = desc.timeout;
+	set->gc_int = desc.gc_int;
 
 	set->field_count = desc.field_count;
 	for (i = 0; i < desc.field_count; i++)
@@ -4413,80 +4903,54 @@
 	if (err < 0)
 		goto err_set_init;
 
-	if (nla[NFTA_SET_EXPR]) {
-		expr = nft_set_elem_expr_alloc(&ctx, set, nla[NFTA_SET_EXPR]);
-		if (IS_ERR(expr)) {
-			err = PTR_ERR(expr);
-			goto err_set_expr_alloc;
-		}
-		set->exprs[0] = expr;
-		set->num_exprs++;
-	} else if (nla[NFTA_SET_EXPRESSIONS]) {
-		struct nft_expr *expr;
-		struct nlattr *tmp;
-		int left;
-
-		if (!(flags & NFT_SET_EXPR)) {
-			err = -EINVAL;
-			goto err_set_expr_alloc;
-		}
-		i = 0;
-		nla_for_each_nested(tmp, nla[NFTA_SET_EXPRESSIONS], left) {
-			if (i == NFT_SET_EXPR_MAX) {
-				err = -E2BIG;
-				goto err_set_expr_alloc;
-			}
-			if (nla_type(tmp) != NFTA_LIST_ELEM) {
-				err = -EINVAL;
-				goto err_set_expr_alloc;
-			}
-			expr = nft_set_elem_expr_alloc(&ctx, set, tmp);
-			if (IS_ERR(expr)) {
-				err = PTR_ERR(expr);
-				goto err_set_expr_alloc;
-			}
-			set->exprs[i++] = expr;
-			set->num_exprs++;
-		}
-	}
+	err = nft_set_expr_alloc(&ctx, set, nla, set->exprs, &num_exprs, flags);
+	if (err < 0)
+		goto err_set_destroy;
 
+	set->num_exprs = num_exprs;
 	set->handle = nf_tables_alloc_handle(table);
+	INIT_LIST_HEAD(&set->pending_update);
 
 	err = nft_trans_set_add(&ctx, NFT_MSG_NEWSET, set);
 	if (err < 0)
 		goto err_set_expr_alloc;
 
 	list_add_tail_rcu(&set->list, &table->sets);
-	table->use++;
+
 	return 0;
 
 err_set_expr_alloc:
 	for (i = 0; i < set->num_exprs; i++)
 		nft_expr_destroy(&ctx, set->exprs[i]);
-
-	ops->destroy(set);
+err_set_destroy:
+	ops->destroy(&ctx, set);
 err_set_init:
 	kfree(set->name);
 err_set_name:
 	kvfree(set);
+err_alloc:
+	nft_use_dec_restore(&table->use);
+
 	return err;
 }
 
-struct nft_set_elem_catchall {
-	struct list_head	list;
-	struct rcu_head		rcu;
-	void			*elem;
-};
-
 static void nft_set_catchall_destroy(const struct nft_ctx *ctx,
 				     struct nft_set *set)
 {
-	struct nft_set_elem_catchall *catchall;
+	struct nft_set_elem_catchall *next, *catchall;
 
-	list_for_each_entry_rcu(catchall, &set->catchall_list, list) {
+	list_for_each_entry_safe(catchall, next, &set->catchall_list, list) {
 		list_del_rcu(&catchall->list);
-		nft_set_elem_destroy(set, catchall->elem, true);
-		kfree_rcu(catchall);
+		nf_tables_set_elem_destroy(ctx, set, catchall->elem);
+		kfree_rcu(catchall, rcu);
+	}
+}
+
+static void nft_set_put(struct nft_set *set)
+{
+	if (refcount_dec_and_test(&set->refs)) {
+		kfree(set->name);
+		kvfree(set);
 	}
 }
 
@@ -4500,10 +4964,9 @@
 	for (i = 0; i < set->num_exprs; i++)
 		nft_expr_destroy(ctx, set->exprs[i]);
 
-	set->ops->destroy(set);
+	set->ops->destroy(ctx, set);
 	nft_set_catchall_destroy(ctx, set);
-	kfree(set->name);
-	kvfree(set);
+	nft_set_put(set);
 }
 
 static int nf_tables_delset(struct sk_buff *skb, const struct nfnl_info *info,
@@ -4577,6 +5040,11 @@
 					const struct nft_set_iter *iter,
 					struct nft_set_elem *elem)
 {
+	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
+
+	if (!nft_set_elem_active(ext, iter->genmask))
+		return 0;
+
 	return nft_setelem_data_validate(ctx, set, elem);
 }
 
@@ -4609,9 +5077,6 @@
 	struct nft_set_binding *i;
 	struct nft_set_iter iter;
 
-	if (set->use == UINT_MAX)
-		return -EOVERFLOW;
-
 	if (!list_empty(&set->bindings) && nft_set_is_anonymous(set))
 		return -EBUSY;
 
@@ -4626,6 +5091,7 @@
 		}
 
 		iter.genmask	= nft_genmask_next(ctx->net);
+		iter.type	= NFT_ITER_UPDATE;
 		iter.skip 	= 0;
 		iter.count	= 0;
 		iter.err	= 0;
@@ -4639,10 +5105,12 @@
 			return iter.err;
 	}
 bind:
+	if (!nft_use_inc(&set->use))
+		return -EMFILE;
+
 	binding->chain = ctx->chain;
 	list_add_tail_rcu(&binding->list, &set->bindings);
 	nft_set_trans_bind(ctx, set);
-	set->use++;
 
 	return 0;
 }
@@ -4655,23 +5123,111 @@
 
 	if (list_empty(&set->bindings) && nft_set_is_anonymous(set)) {
 		list_del_rcu(&set->list);
+		set->dead = 1;
 		if (event)
 			nf_tables_set_notify(ctx, set, NFT_MSG_DELSET,
 					     GFP_KERNEL);
 	}
 }
 
+static void nft_setelem_data_activate(const struct net *net,
+				      const struct nft_set *set,
+				      struct nft_set_elem *elem);
+
+static int nft_mapelem_activate(const struct nft_ctx *ctx,
+				struct nft_set *set,
+				const struct nft_set_iter *iter,
+				struct nft_set_elem *elem)
+{
+	struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
+
+	/* called from abort path, reverse check to undo changes. */
+	if (nft_set_elem_active(ext, iter->genmask))
+		return 0;
+
+	nft_clear(ctx->net, ext);
+	nft_setelem_data_activate(ctx->net, set, elem);
+
+	return 0;
+}
+
+static void nft_map_catchall_activate(const struct nft_ctx *ctx,
+				      struct nft_set *set)
+{
+	u8 genmask = nft_genmask_next(ctx->net);
+	struct nft_set_elem_catchall *catchall;
+	struct nft_set_elem elem;
+	struct nft_set_ext *ext;
+
+	list_for_each_entry(catchall, &set->catchall_list, list) {
+		ext = nft_set_elem_ext(set, catchall->elem);
+		if (!nft_set_elem_active(ext, genmask))
+			continue;
+
+		nft_clear(ctx->net, ext);
+		elem.priv = catchall->elem;
+		nft_setelem_data_activate(ctx->net, set, &elem);
+		break;
+	}
+}
+
+static void nft_map_activate(const struct nft_ctx *ctx, struct nft_set *set)
+{
+	struct nft_set_iter iter = {
+		.genmask	= nft_genmask_next(ctx->net),
+		.type		= NFT_ITER_UPDATE,
+		.fn		= nft_mapelem_activate,
+	};
+
+	set->ops->walk(ctx, set, &iter);
+	WARN_ON_ONCE(iter.err);
+
+	nft_map_catchall_activate(ctx, set);
+}
+
+void nf_tables_activate_set(const struct nft_ctx *ctx, struct nft_set *set)
+{
+	if (nft_set_is_anonymous(set)) {
+		if (set->flags & (NFT_SET_MAP | NFT_SET_OBJECT))
+			nft_map_activate(ctx, set);
+
+		nft_clear(ctx->net, set);
+	}
+
+	nft_use_inc_restore(&set->use);
+}
+EXPORT_SYMBOL_GPL(nf_tables_activate_set);
+
 void nf_tables_deactivate_set(const struct nft_ctx *ctx, struct nft_set *set,
 			      struct nft_set_binding *binding,
 			      enum nft_trans_phase phase)
 {
 	switch (phase) {
+	case NFT_TRANS_PREPARE_ERROR:
+		nft_set_trans_unbind(ctx, set);
+		if (nft_set_is_anonymous(set))
+			nft_deactivate_next(ctx->net, set);
+		else
+			list_del_rcu(&binding->list);
+
+		nft_use_dec(&set->use);
+		break;
 	case NFT_TRANS_PREPARE:
-		set->use--;
+		if (nft_set_is_anonymous(set)) {
+			if (set->flags & (NFT_SET_MAP | NFT_SET_OBJECT))
+				nft_map_deactivate(ctx, set);
+
+			nft_deactivate_next(ctx->net, set);
+		}
+		nft_use_dec(&set->use);
 		return;
 	case NFT_TRANS_ABORT:
 	case NFT_TRANS_RELEASE:
-		set->use--;
+		if (nft_set_is_anonymous(set) &&
+		    set->flags & (NFT_SET_MAP | NFT_SET_OBJECT))
+			nft_map_deactivate(ctx, set);
+
+		nft_use_dec(&set->use);
 		fallthrough;
 	default:
 		nf_tables_unbind_set(ctx, set, binding,
@@ -4811,8 +5367,7 @@
 
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_DATA) &&
 	    nft_data_dump(skb, NFTA_SET_ELEM_DATA, nft_set_ext_data(ext),
-			  set->dtype == NFT_DATA_VERDICT ? NFT_DATA_VERDICT : NFT_DATA_VALUE,
-			  set->dlen) < 0)
+			  nft_set_datatype(set), set->dlen) < 0)
 		goto nla_put_failure;
 
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_EXPRESSIONS) &&
@@ -4878,8 +5433,15 @@
 				  const struct nft_set_iter *iter,
 				  struct nft_set_elem *elem)
 {
+	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
 	struct nft_set_dump_args *args;
 
+	if (!nft_set_elem_active(ext, iter->genmask))
+		return 0;
+
+	if (nft_set_elem_expired(ext) || nft_set_elem_is_dead(ext))
+		return 0;
+
 	args = container_of(iter, struct nft_set_dump_args, iter);
 	return nf_tables_fill_setelem(args->skb, set, elem);
 }
@@ -4928,6 +5490,8 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
+	cb->seq = READ_ONCE(nft_net->base_seq);
+
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (dump_ctx->ctx.family != NFPROTO_UNSPEC &&
 		    dump_ctx->ctx.family != table->family)
@@ -4971,6 +5535,7 @@
 	args.cb			= cb;
 	args.skb		= skb;
 	args.iter.genmask	= nft_genmask_cur(net);
+	args.iter.type		= NFT_ITER_READ;
 	args.iter.skip		= cb->args[0];
 	args.iter.count		= 0;
 	args.iter.err		= 0;
@@ -5063,6 +5628,9 @@
 	if (!(set->flags & NFT_SET_INTERVAL) &&
 	    *flags & NFT_SET_ELEM_INTERVAL_END)
 		return -EINVAL;
+	if ((*flags & (NFT_SET_ELEM_INTERVAL_END | NFT_SET_ELEM_CATCHALL)) ==
+	    (NFT_SET_ELEM_INTERVAL_END | NFT_SET_ELEM_CATCHALL))
+		return -EINVAL;
 
 	return 0;
 }
@@ -5070,19 +5638,13 @@
 static int nft_setelem_parse_key(struct nft_ctx *ctx, struct nft_set *set,
 				 struct nft_data *key, struct nlattr *attr)
 {
-	struct nft_data_desc desc;
-	int err;
-
-	err = nft_data_init(ctx, key, NFT_DATA_VALUE_MAXLEN, &desc, attr);
-	if (err < 0)
-		return err;
-
-	if (desc.type != NFT_DATA_VALUE || desc.len != set->klen) {
-		nft_data_release(key, desc.type);
-		return -EINVAL;
-	}
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= NFT_DATA_VALUE_MAXLEN,
+		.len	= set->klen,
+	};
 
-	return 0;
+	return nft_data_init(ctx, key, &desc, attr);
 }
 
 static int nft_setelem_parse_data(struct nft_ctx *ctx, struct nft_set *set,
@@ -5090,18 +5652,19 @@
 				  struct nft_data *data,
 				  struct nlattr *attr)
 {
-	int err;
+	u32 dtype;
 
-	err = nft_data_init(ctx, data, NFT_DATA_VALUE_MAXLEN, desc, attr);
-	if (err < 0)
-		return err;
+	if (set->dtype == NFT_DATA_VERDICT)
+		dtype = NFT_DATA_VERDICT;
+	else
+		dtype = NFT_DATA_VALUE;
 
-	if (desc->type != NFT_DATA_VERDICT && desc->len != set->dlen) {
-		nft_data_release(data, desc->type);
-		return -EINVAL;
-	}
+	desc->type = dtype;
+	desc->size = NFT_DATA_VALUE_MAXLEN;
+	desc->len = set->dlen;
+	desc->flags = NFT_DATA_DESC_SETELEM;
 
-	return 0;
+	return nft_data_init(ctx, data, desc, attr);
 }
 
 static void *nft_setelem_catchall_get(const struct net *net,
@@ -5216,7 +5779,7 @@
 	int rem, err = 0;
 
 	table = nft_table_lookup(net, nla[NFTA_SET_ELEM_LIST_TABLE], family,
-				 genmask, NETLINK_CB(skb).portid);
+				 genmask, 0);
 	if (IS_ERR(table)) {
 		NL_SET_BAD_ATTR(extack, nla[NFTA_SET_ELEM_LIST_TABLE]);
 		return PTR_ERR(table);
@@ -5249,8 +5812,10 @@
 
 	nla_for_each_nested(attr, nla[NFTA_SET_ELEM_LIST_ELEMENTS], rem) {
 		err = nft_get_set_elem(&ctx, set, attr);
-		if (err < 0)
+		if (err < 0) {
+			NL_SET_BAD_ATTR(extack, attr);
 			break;
+		}
 	}
 
 	return err;
@@ -5318,9 +5883,6 @@
 		return expr;
 
 	err = -EOPNOTSUPP;
-	if (!(expr->ops->type->flags & NFT_EXPR_STATEFUL))
-		goto err_set_elem_expr;
-
 	if (expr->ops->type->flags & NFT_EXPR_GC) {
 		if (set->flags & NFT_SET_TIMEOUT)
 			goto err_set_elem_expr;
@@ -5389,6 +5951,7 @@
 		__nft_set_elem_expr_destroy(ctx, expr);
 }
 
+/* Drop references and destroy. Called from gc, dynset and abort path. */
 void nft_set_elem_destroy(const struct nft_set *set, void *elem,
 			  bool destroy_expr)
 {
@@ -5405,16 +5968,16 @@
 		nft_set_elem_expr_destroy(&ctx, nft_set_ext_expr(ext));
 
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_OBJREF))
-		(*nft_set_ext_obj(ext))->use--;
+		nft_use_dec(&(*nft_set_ext_obj(ext))->use);
 	kfree(elem);
 }
 EXPORT_SYMBOL_GPL(nft_set_elem_destroy);
 
-/* Only called from commit path, nft_setelem_data_deactivate() already deals
- * with the refcounting from the preparation phase.
+/* Destroy element. References have been already dropped in the preparation
+ * path via nft_setelem_data_deactivate().
  */
-static void nf_tables_set_elem_destroy(const struct nft_ctx *ctx,
-				       const struct nft_set *set, void *elem)
+void nf_tables_set_elem_destroy(const struct nft_ctx *ctx,
+				const struct nft_set *set, void *elem)
 {
 	struct nft_set_ext *ext = nft_set_elem_ext(set, elem);
 
@@ -5431,13 +5994,13 @@
 	int err, i, k;
 
 	for (i = 0; i < set->num_exprs; i++) {
-		expr = kzalloc(set->exprs[i]->ops->size, GFP_KERNEL);
+		expr = kzalloc(set->exprs[i]->ops->size, GFP_KERNEL_ACCOUNT);
 		if (!expr)
 			goto err_expr;
 
-		err = nft_expr_clone(expr, set->exprs[i]);
+		err = nft_expr_clone(expr, set->exprs[i], GFP_KERNEL_ACCOUNT);
 		if (err < 0) {
-			nft_expr_destroy(ctx, expr);
+			kfree(expr);
 			goto err_expr;
 		}
 		expr_array[i] = expr;
@@ -5463,7 +6026,7 @@
 
 	for (i = 0; i < num_exprs; i++) {
 		expr = nft_setelem_expr_at(elem_expr, elem_expr->size);
-		err = nft_expr_clone(expr, expr_array[i]);
+		err = nft_expr_clone(expr, expr_array[i], GFP_KERNEL_ACCOUNT);
 		if (err < 0)
 			goto err_elem_expr_setup;
 
@@ -5493,7 +6056,8 @@
 	list_for_each_entry_rcu(catchall, &set->catchall_list, list) {
 		ext = nft_set_elem_ext(set, catchall->elem);
 		if (nft_set_elem_active(ext, genmask) &&
-		    !nft_set_elem_expired(ext))
+		    !nft_set_elem_expired(ext) &&
+		    !nft_set_elem_is_dead(ext))
 			return ext;
 	}
 
@@ -5501,29 +6065,6 @@
 }
 EXPORT_SYMBOL_GPL(nft_set_catchall_lookup);
 
-void *nft_set_catchall_gc(const struct nft_set *set)
-{
-	struct nft_set_elem_catchall *catchall, *next;
-	struct nft_set_ext *ext;
-	void *elem = NULL;
-
-	list_for_each_entry_safe(catchall, next, &set->catchall_list, list) {
-		ext = nft_set_elem_ext(set, catchall->elem);
-
-		if (!nft_set_elem_expired(ext) ||
-		    nft_set_elem_mark_busy(ext))
-			continue;
-
-		elem = catchall->elem;
-		list_del_rcu(&catchall->list);
-		kfree_rcu(catchall, rcu);
-		break;
-	}
-
-	return elem;
-}
-EXPORT_SYMBOL_GPL(nft_set_catchall_gc);
-
 static int nft_setelem_catchall_insert(const struct net *net,
 				       struct nft_set *set,
 				       const struct nft_set_elem *elem,
@@ -5584,8 +6125,7 @@
 	struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
 
 	if (nft_setelem_is_catchall(set, elem)) {
-		nft_set_elem_change_active(net, set, ext);
-		nft_set_elem_clear_busy(ext);
+		nft_clear(net, ext);
 	} else {
 		set->ops->activate(net, set, elem);
 	}
@@ -5600,8 +6140,7 @@
 
 	list_for_each_entry(catchall, &set->catchall_list, list) {
 		ext = nft_set_elem_ext(set, catchall->elem);
-		if (!nft_is_active(net, ext) ||
-		    nft_set_elem_mark_busy(ext))
+		if (!nft_is_active_next(net, ext))
 			continue;
 
 		kfree(elem->priv);
@@ -5644,6 +6183,12 @@
 	return ret;
 }
 
+static void nft_setelem_catchall_destroy(struct nft_set_elem_catchall *catchall)
+{
+	list_del_rcu(&catchall->list);
+	kfree_rcu(catchall, rcu);
+}
+
 static void nft_setelem_catchall_remove(const struct net *net,
 					const struct nft_set *set,
 					const struct nft_set_elem *elem)
@@ -5652,8 +6197,7 @@
 
 	list_for_each_entry_safe(catchall, next, &set->catchall_list, list) {
 		if (catchall->elem == elem->priv) {
-			list_del_rcu(&catchall->list);
-			kfree_rcu(catchall);
+			nft_setelem_catchall_destroy(catchall);
 			break;
 		}
 	}
@@ -5669,6 +6213,25 @@
 		set->ops->remove(net, set, elem);
 }
 
+static bool nft_setelem_valid_key_end(const struct nft_set *set,
+				      struct nlattr **nla, u32 flags)
+{
+	if ((set->flags & (NFT_SET_CONCAT | NFT_SET_INTERVAL)) ==
+			  (NFT_SET_CONCAT | NFT_SET_INTERVAL)) {
+		if (flags & NFT_SET_ELEM_INTERVAL_END)
+			return false;
+
+		if (nla[NFTA_SET_ELEM_KEY_END] &&
+		    flags & NFT_SET_ELEM_CATCHALL)
+			return false;
+	} else {
+		if (nla[NFTA_SET_ELEM_KEY_END])
+			return false;
+	}
+
+	return true;
+}
+
 static int nft_add_set_elem(struct nft_ctx *ctx, struct nft_set *set,
 			    const struct nlattr *attr, u32 nlmsg_flags)
 {
@@ -5701,11 +6264,15 @@
 	if (err < 0)
 		return err;
 
-	if (!nla[NFTA_SET_ELEM_KEY] && !(flags & NFT_SET_ELEM_CATCHALL))
+	if (((flags & NFT_SET_ELEM_CATCHALL) && nla[NFTA_SET_ELEM_KEY]) ||
+	    (!(flags & NFT_SET_ELEM_CATCHALL) && !nla[NFTA_SET_ELEM_KEY]))
 		return -EINVAL;
 
-	if (flags != 0)
-		nft_set_ext_add(&tmpl, NFT_SET_EXT_FLAGS);
+	if (flags != 0) {
+		err = nft_set_ext_add(&tmpl, NFT_SET_EXT_FLAGS);
+		if (err < 0)
+			return err;
+	}
 
 	if (set->flags & NFT_SET_MAP) {
 		if (nla[NFTA_SET_ELEM_DATA] == NULL &&
@@ -5716,6 +6283,18 @@
 			return -EINVAL;
 	}
 
+	if (set->flags & NFT_SET_OBJECT) {
+		if (!nla[NFTA_SET_ELEM_OBJREF] &&
+		    !(flags & NFT_SET_ELEM_INTERVAL_END))
+			return -EINVAL;
+	} else {
+		if (nla[NFTA_SET_ELEM_OBJREF])
+			return -EINVAL;
+	}
+
+	if (!nft_setelem_valid_key_end(set, nla, flags))
+		return -EINVAL;
+
 	if ((flags & NFT_SET_ELEM_INTERVAL_END) &&
 	     (nla[NFTA_SET_ELEM_DATA] ||
 	      nla[NFTA_SET_ELEM_OBJREF] ||
@@ -5723,6 +6302,7 @@
 	      nla[NFTA_SET_ELEM_EXPIRATION] ||
 	      nla[NFTA_SET_ELEM_USERDATA] ||
 	      nla[NFTA_SET_ELEM_EXPR] ||
+	      nla[NFTA_SET_ELEM_KEY_END] ||
 	      nla[NFTA_SET_ELEM_EXPRESSIONS]))
 		return -EINVAL;
 
@@ -5734,7 +6314,8 @@
 					    &timeout);
 		if (err)
 			return err;
-	} else if (set->flags & NFT_SET_TIMEOUT) {
+	} else if (set->flags & NFT_SET_TIMEOUT &&
+		   !(flags & NFT_SET_ELEM_INTERVAL_END)) {
 		timeout = set->timeout;
 	}
 
@@ -5742,10 +6323,16 @@
 	if (nla[NFTA_SET_ELEM_EXPIRATION] != NULL) {
 		if (!(set->flags & NFT_SET_TIMEOUT))
 			return -EINVAL;
+		if (timeout == 0)
+			return -EOPNOTSUPP;
+
 		err = nf_msecs_to_jiffies64(nla[NFTA_SET_ELEM_EXPIRATION],
 					    &expiration);
 		if (err)
 			return err;
+
+		if (expiration > timeout)
+			return -ERANGE;
 	}
 
 	if (nla[NFTA_SET_ELEM_EXPR]) {
@@ -5800,7 +6387,8 @@
 			err = -EOPNOTSUPP;
 			goto err_set_elem_expr;
 		}
-	} else if (set->num_exprs > 0) {
+	} else if (set->num_exprs > 0 &&
+		   !(flags & NFT_SET_ELEM_INTERVAL_END)) {
 		err = nft_set_elem_expr_clone(ctx, set, expr_array);
 		if (err < 0)
 			goto err_set_elem_expr_clone;
@@ -5814,7 +6402,9 @@
 		if (err < 0)
 			goto err_set_elem_expr;
 
-		nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY, set->klen);
+		err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY, set->klen);
+		if (err < 0)
+			goto err_parse_key;
 	}
 
 	if (nla[NFTA_SET_ELEM_KEY_END]) {
@@ -5823,37 +6413,52 @@
 		if (err < 0)
 			goto err_parse_key;
 
-		nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY_END, set->klen);
+		err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY_END, set->klen);
+		if (err < 0)
+			goto err_parse_key_end;
 	}
 
 	if (timeout > 0) {
-		nft_set_ext_add(&tmpl, NFT_SET_EXT_EXPIRATION);
-		if (timeout != set->timeout)
-			nft_set_ext_add(&tmpl, NFT_SET_EXT_TIMEOUT);
+		err = nft_set_ext_add(&tmpl, NFT_SET_EXT_EXPIRATION);
+		if (err < 0)
+			goto err_parse_key_end;
+
+		if (timeout != set->timeout) {
+			err = nft_set_ext_add(&tmpl, NFT_SET_EXT_TIMEOUT);
+			if (err < 0)
+				goto err_parse_key_end;
+		}
 	}
 
 	if (num_exprs) {
 		for (i = 0; i < num_exprs; i++)
 			size += expr_array[i]->ops->size;
 
-		nft_set_ext_add_length(&tmpl, NFT_SET_EXT_EXPRESSIONS,
-				       sizeof(struct nft_set_elem_expr) +
-				       size);
+		err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_EXPRESSIONS,
+					     sizeof(struct nft_set_elem_expr) + size);
+		if (err < 0)
+			goto err_parse_key_end;
 	}
 
 	if (nla[NFTA_SET_ELEM_OBJREF] != NULL) {
-		if (!(set->flags & NFT_SET_OBJECT)) {
-			err = -EINVAL;
-			goto err_parse_key_end;
-		}
 		obj = nft_obj_lookup(ctx->net, ctx->table,
 				     nla[NFTA_SET_ELEM_OBJREF],
 				     set->objtype, genmask);
 		if (IS_ERR(obj)) {
 			err = PTR_ERR(obj);
+			obj = NULL;
 			goto err_parse_key_end;
 		}
-		nft_set_ext_add(&tmpl, NFT_SET_EXT_OBJREF);
+
+		if (!nft_use_inc(&obj->use)) {
+			err = -EMFILE;
+			obj = NULL;
+			goto err_parse_key_end;
+		}
+
+		err = nft_set_ext_add(&tmpl, NFT_SET_EXT_OBJREF);
+		if (err < 0)
+			goto err_parse_key_end;
 	}
 
 	if (nla[NFTA_SET_ELEM_DATA] != NULL) {
@@ -5887,7 +6492,9 @@
 							  NFT_VALIDATE_NEED);
 		}
 
-		nft_set_ext_add_length(&tmpl, NFT_SET_EXT_DATA, desc.len);
+		err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_DATA, desc.len);
+		if (err < 0)
+			goto err_parse_data;
 	}
 
 	/* The full maximum length of userdata can exceed the maximum
@@ -5897,9 +6504,12 @@
 	ulen = 0;
 	if (nla[NFTA_SET_ELEM_USERDATA] != NULL) {
 		ulen = nla_len(nla[NFTA_SET_ELEM_USERDATA]);
-		if (ulen > 0)
-			nft_set_ext_add_length(&tmpl, NFT_SET_EXT_USERDATA,
-					       ulen);
+		if (ulen > 0) {
+			err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_USERDATA,
+						     ulen);
+			if (err < 0)
+				goto err_parse_data;
+		}
 	}
 
 	err = -ENOMEM;
@@ -5917,10 +6527,9 @@
 		udata->len = ulen - 1;
 		nla_memcpy(&udata->data, nla[NFTA_SET_ELEM_USERDATA], ulen);
 	}
-	if (obj) {
+	if (obj)
 		*nft_set_ext_obj(ext) = obj;
-		obj->use++;
-	}
+
 	err = nft_set_elem_expr_setup(ctx, ext, expr_array, num_exprs);
 	if (err < 0)
 		goto err_elem_expr;
@@ -5931,7 +6540,7 @@
 		goto err_elem_expr;
 	}
 
-	ext->genmask = nft_genmask_cur(ctx->net) | NFT_SET_ELEM_BUSY_MASK;
+	ext->genmask = nft_genmask_cur(ctx->net);
 
 	err = nft_setelem_insert(ctx->net, set, &elem, &ext2, flags);
 	if (err) {
@@ -5975,14 +6584,14 @@
 err_element_clash:
 	kfree(trans);
 err_elem_expr:
-	if (obj)
-		obj->use--;
-
 	nf_tables_set_elem_destroy(ctx, set, elem.priv);
 err_parse_data:
 	if (nla[NFTA_SET_ELEM_DATA] != NULL)
 		nft_data_release(&elem.data.val, desc.type);
 err_parse_key_end:
+	if (obj)
+		nft_use_dec_restore(&obj->use);
+
 	nft_data_release(&elem.key_end.val, NFT_DATA_VALUE);
 err_parse_key:
 	nft_data_release(&elem.key.val, NFT_DATA_VALUE);
@@ -6023,15 +6632,18 @@
 	if (IS_ERR(set))
 		return PTR_ERR(set);
 
-	if (!list_empty(&set->bindings) && set->flags & NFT_SET_CONSTANT)
+	if (!list_empty(&set->bindings) &&
+	    (set->flags & (NFT_SET_CONSTANT | NFT_SET_ANONYMOUS)))
 		return -EBUSY;
 
 	nft_ctx_init(&ctx, net, skb, info->nlh, family, table, NULL, nla);
 
 	nla_for_each_nested(attr, nla[NFTA_SET_ELEM_LIST_ELEMENTS], rem) {
 		err = nft_add_set_elem(&ctx, set, attr, info->nlh->nlmsg_flags);
-		if (err < 0)
+		if (err < 0) {
+			NL_SET_BAD_ATTR(extack, attr);
 			return err;
+		}
 	}
 
 	if (nft_net->validate_state == NFT_VALIDATE_DO)
@@ -6054,23 +6666,13 @@
 void nft_data_hold(const struct nft_data *data, enum nft_data_types type)
 {
 	struct nft_chain *chain;
-	struct nft_rule *rule;
 
 	if (type == NFT_DATA_VERDICT) {
 		switch (data->verdict.code) {
 		case NFT_JUMP:
 		case NFT_GOTO:
 			chain = data->verdict.chain;
-			chain->use++;
-
-			if (!nft_chain_is_bound(chain))
-				break;
-
-			chain->table->use++;
-			list_for_each_entry(rule, &chain->rules, list)
-				chain->use++;
-
-			nft_chain_add(chain->table, chain);
+			nft_use_inc_restore(&chain->use);
 			break;
 		}
 	}
@@ -6085,19 +6687,19 @@
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_DATA))
 		nft_data_hold(nft_set_ext_data(ext), set->dtype);
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_OBJREF))
-		(*nft_set_ext_obj(ext))->use++;
+		nft_use_inc_restore(&(*nft_set_ext_obj(ext))->use);
 }
 
-static void nft_setelem_data_deactivate(const struct net *net,
-					const struct nft_set *set,
-					struct nft_set_elem *elem)
+void nft_setelem_data_deactivate(const struct net *net,
+				 const struct nft_set *set,
+				 struct nft_set_elem *elem)
 {
 	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
 
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_DATA))
 		nft_data_release(nft_set_ext_data(ext), set->dtype);
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_OBJREF))
-		(*nft_set_ext_obj(ext))->use--;
+		nft_use_dec(&(*nft_set_ext_obj(ext))->use);
 }
 
 static int nft_del_setelem(struct nft_ctx *ctx, struct nft_set *set,
@@ -6123,10 +6725,16 @@
 	if (!nla[NFTA_SET_ELEM_KEY] && !(flags & NFT_SET_ELEM_CATCHALL))
 		return -EINVAL;
 
+	if (!nft_setelem_valid_key_end(set, nla, flags))
+		return -EINVAL;
+
 	nft_set_ext_prepare(&tmpl);
 
-	if (flags != 0)
-		nft_set_ext_add(&tmpl, NFT_SET_EXT_FLAGS);
+	if (flags != 0) {
+		err = nft_set_ext_add(&tmpl, NFT_SET_EXT_FLAGS);
+		if (err < 0)
+			return err;
+	}
 
 	if (nla[NFTA_SET_ELEM_KEY]) {
 		err = nft_setelem_parse_key(ctx, set, &elem.key.val,
@@ -6134,16 +6742,20 @@
 		if (err < 0)
 			return err;
 
-		nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY, set->klen);
+		err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY, set->klen);
+		if (err < 0)
+			goto fail_elem;
 	}
 
 	if (nla[NFTA_SET_ELEM_KEY_END]) {
 		err = nft_setelem_parse_key(ctx, set, &elem.key_end.val,
 					    nla[NFTA_SET_ELEM_KEY_END]);
 		if (err < 0)
-			return err;
+			goto fail_elem;
 
-		nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY_END, set->klen);
+		err = nft_set_ext_add_length(&tmpl, NFT_SET_EXT_KEY_END, set->klen);
+		if (err < 0)
+			goto fail_elem_key_end;
 	}
 
 	err = -ENOMEM;
@@ -6151,7 +6763,7 @@
 				      elem.key_end.val.data, NULL, 0, 0,
 				      GFP_KERNEL);
 	if (elem.priv == NULL)
-		goto fail_elem;
+		goto fail_elem_key_end;
 
 	ext = nft_set_elem_ext(set, elem.priv);
 	if (flags)
@@ -6175,6 +6787,8 @@
 	kfree(trans);
 fail_trans:
 	kfree(elem.priv);
+fail_elem_key_end:
+	nft_data_release(&elem.key_end.val, NFT_DATA_VALUE);
 fail_elem:
 	nft_data_release(&elem.key.val, NFT_DATA_VALUE);
 	return err;
@@ -6185,9 +6799,13 @@
 			     const struct nft_set_iter *iter,
 			     struct nft_set_elem *elem)
 {
+	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
 	struct nft_trans *trans;
 	int err;
 
+	if (!nft_set_elem_active(ext, iter->genmask))
+		return 0;
+
 	trans = nft_trans_alloc_gfp(ctx, NFT_MSG_DELSETELEM,
 				    sizeof(struct nft_trans_elem), GFP_ATOMIC);
 	if (!trans)
@@ -6240,14 +6858,14 @@
 
 	list_for_each_entry_rcu(catchall, &set->catchall_list, list) {
 		ext = nft_set_elem_ext(set, catchall->elem);
-		if (!nft_set_elem_active(ext, genmask) ||
-		    nft_set_elem_mark_busy(ext))
+		if (!nft_set_elem_active(ext, genmask))
 			continue;
 
 		elem.priv = catchall->elem;
 		ret = __nft_set_catchall_flush(ctx, set, &elem);
 		if (ret < 0)
 			break;
+		nft_set_elem_change_active(ctx->net, set, ext);
 	}
 
 	return ret;
@@ -6257,6 +6875,7 @@
 {
 	struct nft_set_iter iter = {
 		.genmask	= genmask,
+		.type		= NFT_ITER_UPDATE,
 		.fn		= nft_setelem_flush,
 	};
 
@@ -6291,7 +6910,11 @@
 	set = nft_set_lookup(table, nla[NFTA_SET_ELEM_LIST_SET], genmask);
 	if (IS_ERR(set))
 		return PTR_ERR(set);
-	if (!list_empty(&set->bindings) && set->flags & NFT_SET_CONSTANT)
+
+	if (nft_set_is_anonymous(set))
+		return -EOPNOTSUPP;
+
+	if (!list_empty(&set->bindings) && (set->flags & NFT_SET_CONSTANT))
 		return -EBUSY;
 
 	nft_ctx_init(&ctx, net, skb, info->nlh, family, table, NULL, nla);
@@ -6301,35 +6924,14 @@
 
 	nla_for_each_nested(attr, nla[NFTA_SET_ELEM_LIST_ELEMENTS], rem) {
 		err = nft_del_setelem(&ctx, set, attr);
-		if (err < 0)
+		if (err < 0) {
+			NL_SET_BAD_ATTR(extack, attr);
 			break;
+		}
 	}
 	return err;
 }
 
-void nft_set_gc_batch_release(struct rcu_head *rcu)
-{
-	struct nft_set_gc_batch *gcb;
-	unsigned int i;
-
-	gcb = container_of(rcu, struct nft_set_gc_batch, head.rcu);
-	for (i = 0; i < gcb->head.cnt; i++)
-		nft_set_elem_destroy(gcb->head.set, gcb->elems[i], true);
-	kfree(gcb);
-}
-
-struct nft_set_gc_batch *nft_set_gc_batch_alloc(const struct nft_set *set,
-						gfp_t gfp)
-{
-	struct nft_set_gc_batch *gcb;
-
-	gcb = kzalloc(sizeof(*gcb), gfp);
-	if (gcb == NULL)
-		return gcb;
-	gcb->head.set = set;
-	return gcb;
-}
-
 /*
  * Stateful objects
  */
@@ -6498,11 +7100,15 @@
 	return -1;
 }
 
-static const struct nft_object_type *__nft_obj_type_get(u32 objtype)
+static const struct nft_object_type *__nft_obj_type_get(u32 objtype, u8 family)
 {
 	const struct nft_object_type *type;
 
-	list_for_each_entry(type, &nf_tables_objects, list) {
+	list_for_each_entry_rcu(type, &nf_tables_objects, list) {
+		if (type->family != NFPROTO_UNSPEC &&
+		    type->family != family)
+			continue;
+
 		if (objtype == type->type)
 			return type;
 	}
@@ -6510,13 +7116,17 @@
 }
 
 static const struct nft_object_type *
-nft_obj_type_get(struct net *net, u32 objtype)
+nft_obj_type_get(struct net *net, u32 objtype, u8 family)
 {
 	const struct nft_object_type *type;
 
-	type = __nft_obj_type_get(objtype);
-	if (type != NULL && try_module_get(type->owner))
+	rcu_read_lock();
+	type = __nft_obj_type_get(objtype, family);
+	if (type != NULL && try_module_get(type->owner)) {
+		rcu_read_unlock();
 		return type;
+	}
+	rcu_read_unlock();
 
 	lockdep_nfnl_nft_mutex_not_held();
 #ifdef CONFIG_MODULES
@@ -6535,12 +7145,13 @@
 {
 	struct nft_object *newobj;
 	struct nft_trans *trans;
-	int err;
+	int err = -ENOMEM;
 
+	/* caller must have obtained type->owner reference. */
 	trans = nft_trans_alloc(ctx, NFT_MSG_NEWOBJ,
 				sizeof(struct nft_trans_obj));
 	if (!trans)
-		return -ENOMEM;
+		goto err_trans;
 
 	newobj = nft_obj_init(ctx, type, attr);
 	if (IS_ERR(newobj)) {
@@ -6557,6 +7168,8 @@
 
 err_free_trans:
 	kfree(trans);
+err_trans:
+	module_put(type->owner);
 	return err;
 }
 
@@ -6602,17 +7215,29 @@
 		if (info->nlh->nlmsg_flags & NLM_F_REPLACE)
 			return -EOPNOTSUPP;
 
-		type = __nft_obj_type_get(objtype);
+		if (!obj->ops->update)
+			return 0;
+
+		type = nft_obj_type_get(net, objtype, family);
+		if (WARN_ON_ONCE(IS_ERR(type)))
+			return PTR_ERR(type);
+
 		nft_ctx_init(&ctx, net, skb, info->nlh, family, table, NULL, nla);
 
+		/* type->owner reference is put when transaction object is released. */
 		return nf_tables_updobj(&ctx, type, nla[NFTA_OBJ_DATA], obj);
 	}
 
 	nft_ctx_init(&ctx, net, skb, info->nlh, family, table, NULL, nla);
 
-	type = nft_obj_type_get(net, objtype);
-	if (IS_ERR(type))
-		return PTR_ERR(type);
+	if (!nft_use_inc(&table->use))
+		return -EMFILE;
+
+	type = nft_obj_type_get(net, objtype, family);
+	if (IS_ERR(type)) {
+		err = PTR_ERR(type);
+		goto err_type;
+	}
 
 	obj = nft_obj_init(&ctx, type, nla[NFTA_OBJ_DATA]);
 	if (IS_ERR(obj)) {
@@ -6646,7 +7271,7 @@
 		goto err_obj_ht;
 
 	list_add_tail_rcu(&obj->list, &table->objects);
-	table->use++;
+
 	return 0;
 err_obj_ht:
 	/* queued in transaction log */
@@ -6662,6 +7287,9 @@
 	kfree(obj);
 err_init:
 	module_put(type->owner);
+err_type:
+	nft_use_dec_restore(&table->use);
+
 	return err;
 }
 
@@ -6721,7 +7349,7 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
-	cb->seq = nft_net->base_seq;
+	cb->seq = READ_ONCE(nft_net->base_seq);
 
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (family != NFPROTO_UNSPEC && family != table->family)
@@ -7048,10 +7676,11 @@
 				    enum nft_trans_phase phase)
 {
 	switch (phase) {
+	case NFT_TRANS_PREPARE_ERROR:
 	case NFT_TRANS_PREPARE:
 	case NFT_TRANS_ABORT:
 	case NFT_TRANS_RELEASE:
-		flowtable->use--;
+		nft_use_dec(&flowtable->use);
 		fallthrough;
 	default:
 		return;
@@ -7151,11 +7780,12 @@
 	return err;
 }
 
+/* call under rcu_read_lock */
 static const struct nf_flowtable_type *__nft_flowtable_type_get(u8 family)
 {
 	const struct nf_flowtable_type *type;
 
-	list_for_each_entry(type, &nf_tables_flowtables, list) {
+	list_for_each_entry_rcu(type, &nf_tables_flowtables, list) {
 		if (family == type->family)
 			return type;
 	}
@@ -7167,9 +7797,13 @@
 {
 	const struct nf_flowtable_type *type;
 
+	rcu_read_lock();
 	type = __nft_flowtable_type_get(family);
-	if (type != NULL && try_module_get(type->owner))
+	if (type != NULL && try_module_get(type->owner)) {
+		rcu_read_unlock();
 		return type;
+	}
+	rcu_read_unlock();
 
 	lockdep_nfnl_nft_mutex_not_held();
 #ifdef CONFIG_MODULES
@@ -7191,13 +7825,29 @@
 				    FLOW_BLOCK_UNBIND);
 }
 
-static void nft_unregister_flowtable_net_hooks(struct net *net,
-					       struct list_head *hook_list)
+static void __nft_unregister_flowtable_net_hooks(struct net *net,
+						 struct nft_flowtable *flowtable,
+						 struct list_head *hook_list,
+					         bool release_netdev)
 {
-	struct nft_hook *hook;
+	struct nft_hook *hook, *next;
 
-	list_for_each_entry(hook, hook_list, list)
+	list_for_each_entry_safe(hook, next, hook_list, list) {
 		nf_unregister_net_hook(net, &hook->ops);
+		flowtable->data.type->setup(&flowtable->data, hook->ops.dev,
+					    FLOW_BLOCK_UNBIND);
+		if (release_netdev) {
+			list_del(&hook->list);
+			kfree_rcu(hook, rcu);
+		}
+	}
+}
+
+static void nft_unregister_flowtable_net_hooks(struct net *net,
+					       struct nft_flowtable *flowtable,
+					       struct list_head *hook_list)
+{
+	__nft_unregister_flowtable_net_hooks(net, flowtable, hook_list, false);
 }
 
 static int nft_register_flowtable_net_hooks(struct net *net,
@@ -7290,11 +7940,15 @@
 
 	if (nla[NFTA_FLOWTABLE_FLAGS]) {
 		flags = ntohl(nla_get_be32(nla[NFTA_FLOWTABLE_FLAGS]));
-		if (flags & ~NFT_FLOWTABLE_MASK)
-			return -EOPNOTSUPP;
+		if (flags & ~NFT_FLOWTABLE_MASK) {
+			err = -EOPNOTSUPP;
+			goto err_flowtable_update_hook;
+		}
 		if ((flowtable->data.flags & NFT_FLOWTABLE_HW_OFFLOAD) ^
-		    (flags & NFT_FLOWTABLE_HW_OFFLOAD))
-			return -EOPNOTSUPP;
+		    (flags & NFT_FLOWTABLE_HW_OFFLOAD)) {
+			err = -EOPNOTSUPP;
+			goto err_flowtable_update_hook;
+		}
 	} else {
 		flags = flowtable->data.flags;
 	}
@@ -7383,9 +8037,14 @@
 
 	nft_ctx_init(&ctx, net, skb, info->nlh, family, table, NULL, nla);
 
+	if (!nft_use_inc(&table->use))
+		return -EMFILE;
+
 	flowtable = kzalloc(sizeof(*flowtable), GFP_KERNEL);
-	if (!flowtable)
-		return -ENOMEM;
+	if (!flowtable) {
+		err = -ENOMEM;
+		goto flowtable_alloc;
+	}
 
 	flowtable->table = table;
 	flowtable->handle = nf_tables_alloc_handle(table);
@@ -7440,7 +8099,6 @@
 		goto err5;
 
 	list_add_tail_rcu(&flowtable->list, &table->flowtables);
-	table->use++;
 
 	return 0;
 err5:
@@ -7457,6 +8115,9 @@
 	kfree(flowtable->name);
 err1:
 	kfree(flowtable);
+flowtable_alloc:
+	nft_use_dec_restore(&table->use);
+
 	return err;
 }
 
@@ -7475,6 +8136,7 @@
 {
 	const struct nlattr * const *nla = ctx->nla;
 	struct nft_flowtable_hook flowtable_hook;
+	LIST_HEAD(flowtable_del_list);
 	struct nft_hook *this, *hook;
 	struct nft_trans *trans;
 	int err;
@@ -7490,7 +8152,7 @@
 			err = -ENOENT;
 			goto err_flowtable_del_hook;
 		}
-		hook->inactive = true;
+		list_move(&hook->list, &flowtable_del_list);
 	}
 
 	trans = nft_trans_alloc(ctx, NFT_MSG_DELFLOWTABLE,
@@ -7503,6 +8165,7 @@
 	nft_trans_flowtable(trans) = flowtable;
 	nft_trans_flowtable_update(trans) = true;
 	INIT_LIST_HEAD(&nft_trans_flowtable_hooks(trans));
+	list_splice(&flowtable_del_list, &nft_trans_flowtable_hooks(trans));
 	nft_flowtable_hook_release(&flowtable_hook);
 
 	nft_trans_commit_list_add_tail(ctx->net, trans);
@@ -7510,13 +8173,7 @@
 	return 0;
 
 err_flowtable_del_hook:
-	list_for_each_entry(this, &flowtable_hook.list, list) {
-		hook = nft_hook_list_find(&flowtable->hook_list, this);
-		if (!hook)
-			break;
-
-		hook->inactive = false;
-	}
+	list_splice(&flowtable_del_list, &flowtable->hook_list);
 	nft_flowtable_hook_release(&flowtable_hook);
 
 	return err;
@@ -7641,7 +8298,7 @@
 
 	rcu_read_lock();
 	nft_net = nft_pernet(net);
-	cb->seq = nft_net->base_seq;
+	cb->seq = READ_ONCE(nft_net->base_seq);
 
 	list_for_each_entry_rcu(table, &nft_net->tables, list) {
 		if (family != NFPROTO_UNSPEC && family != table->family)
@@ -7812,10 +8469,8 @@
 
 	flowtable->data.type->free(&flowtable->data);
 	list_for_each_entry_safe(hook, next, &flowtable->hook_list, list) {
-		flowtable->data.type->setup(&flowtable->data, hook->ops.dev,
-					    FLOW_BLOCK_UNBIND);
 		list_del_rcu(&hook->list);
-		kfree(hook);
+		kfree_rcu(hook, rcu);
 	}
 	kfree(flowtable->name);
 	module_put(flowtable->data.type->owner);
@@ -8101,6 +8756,8 @@
 			if (nft_table_validate(net, table) < 0)
 				return -EAGAIN;
 		}
+
+		nft_validate_state_update(net, NFT_VALIDATE_SKIP);
 		break;
 	}
 
@@ -8166,10 +8823,11 @@
 	obj = nft_trans_obj(trans);
 	newobj = nft_trans_obj_newobj(trans);
 
-	if (obj->ops->update)
-		obj->ops->update(obj, newobj);
+	if (WARN_ON_ONCE(!obj->ops->update))
+		return;
 
-	kfree(newobj);
+	obj->ops->update(obj, newobj);
+	nft_obj_destroy(&trans->ctx, newobj);
 }
 
 static void nft_commit_release(struct nft_trans *trans)
@@ -8228,7 +8886,7 @@
 	synchronize_rcu();
 
 	list_for_each_entry_safe(trans, next, &head, list) {
-		list_del(&trans->list);
+		nft_trans_list_del(trans);
 		nft_commit_release(trans);
 	}
 }
@@ -8371,15 +9029,247 @@
 	list_del_rcu(&chain->list);
 }
 
-static void nft_flowtable_hooks_del(struct nft_flowtable *flowtable,
-				    struct list_head *hook_list)
+static void nft_trans_gc_setelem_remove(struct nft_ctx *ctx,
+					struct nft_trans_gc *trans)
 {
-	struct nft_hook *hook, *next;
+	void **priv = trans->priv;
+	unsigned int i;
 
-	list_for_each_entry_safe(hook, next, &flowtable->hook_list, list) {
-		if (hook->inactive)
-			list_move(&hook->list, hook_list);
+	for (i = 0; i < trans->count; i++) {
+		struct nft_set_elem elem = {
+			.priv = priv[i],
+		};
+
+		nft_setelem_data_deactivate(ctx->net, trans->set, &elem);
+		nft_setelem_remove(ctx->net, trans->set, &elem);
+	}
+}
+
+void nft_trans_gc_destroy(struct nft_trans_gc *trans)
+{
+	nft_set_put(trans->set);
+	put_net(trans->net);
+	kfree(trans);
+}
+
+static void nft_trans_gc_trans_free(struct rcu_head *rcu)
+{
+	struct nft_set_elem elem = {};
+	struct nft_trans_gc *trans;
+	struct nft_ctx ctx = {};
+	unsigned int i;
+
+	trans = container_of(rcu, struct nft_trans_gc, rcu);
+	ctx.net	= read_pnet(&trans->set->net);
+
+	for (i = 0; i < trans->count; i++) {
+		elem.priv = trans->priv[i];
+		if (!nft_setelem_is_catchall(trans->set, &elem))
+			atomic_dec(&trans->set->nelems);
+
+		nf_tables_set_elem_destroy(&ctx, trans->set, elem.priv);
+	}
+
+	nft_trans_gc_destroy(trans);
+}
+
+static bool nft_trans_gc_work_done(struct nft_trans_gc *trans)
+{
+	struct nftables_pernet *nft_net;
+	struct nft_ctx ctx = {};
+
+	nft_net = nft_pernet(trans->net);
+
+	mutex_lock(&nft_net->commit_mutex);
+
+	/* Check for race with transaction, otherwise this batch refers to
+	 * stale objects that might not be there anymore. Skip transaction if
+	 * set has been destroyed from control plane transaction in case gc
+	 * worker loses race.
+	 */
+	if (READ_ONCE(nft_net->gc_seq) != trans->seq || trans->set->dead) {
+		mutex_unlock(&nft_net->commit_mutex);
+		return false;
+	}
+
+	ctx.net = trans->net;
+	ctx.table = trans->set->table;
+
+	nft_trans_gc_setelem_remove(&ctx, trans);
+	mutex_unlock(&nft_net->commit_mutex);
+
+	return true;
+}
+
+static void nft_trans_gc_work(struct work_struct *work)
+{
+	struct nft_trans_gc *trans, *next;
+	LIST_HEAD(trans_gc_list);
+
+	spin_lock(&nf_tables_gc_list_lock);
+	list_splice_init(&nf_tables_gc_list, &trans_gc_list);
+	spin_unlock(&nf_tables_gc_list_lock);
+
+	list_for_each_entry_safe(trans, next, &trans_gc_list, list) {
+		list_del(&trans->list);
+		if (!nft_trans_gc_work_done(trans)) {
+			nft_trans_gc_destroy(trans);
+			continue;
+		}
+		call_rcu(&trans->rcu, nft_trans_gc_trans_free);
+	}
+}
+
+struct nft_trans_gc *nft_trans_gc_alloc(struct nft_set *set,
+					unsigned int gc_seq, gfp_t gfp)
+{
+	struct net *net = read_pnet(&set->net);
+	struct nft_trans_gc *trans;
+
+	trans = kzalloc(sizeof(*trans), gfp);
+	if (!trans)
+		return NULL;
+
+	trans->net = maybe_get_net(net);
+	if (!trans->net) {
+		kfree(trans);
+		return NULL;
+	}
+
+	refcount_inc(&set->refs);
+	trans->set = set;
+	trans->seq = gc_seq;
+
+	return trans;
+}
+
+void nft_trans_gc_elem_add(struct nft_trans_gc *trans, void *priv)
+{
+	trans->priv[trans->count++] = priv;
+}
+
+static void nft_trans_gc_queue_work(struct nft_trans_gc *trans)
+{
+	spin_lock(&nf_tables_gc_list_lock);
+	list_add_tail(&trans->list, &nf_tables_gc_list);
+	spin_unlock(&nf_tables_gc_list_lock);
+
+	schedule_work(&trans_gc_work);
+}
+
+static int nft_trans_gc_space(struct nft_trans_gc *trans)
+{
+	return NFT_TRANS_GC_BATCHCOUNT - trans->count;
+}
+
+struct nft_trans_gc *nft_trans_gc_queue_async(struct nft_trans_gc *gc,
+					      unsigned int gc_seq, gfp_t gfp)
+{
+	struct nft_set *set;
+
+	if (nft_trans_gc_space(gc))
+		return gc;
+
+	set = gc->set;
+	nft_trans_gc_queue_work(gc);
+
+	return nft_trans_gc_alloc(set, gc_seq, gfp);
+}
+
+void nft_trans_gc_queue_async_done(struct nft_trans_gc *trans)
+{
+	if (trans->count == 0) {
+		nft_trans_gc_destroy(trans);
+		return;
+	}
+
+	nft_trans_gc_queue_work(trans);
+}
+
+struct nft_trans_gc *nft_trans_gc_queue_sync(struct nft_trans_gc *gc, gfp_t gfp)
+{
+	struct nft_set *set;
+
+	if (WARN_ON_ONCE(!lockdep_commit_lock_is_held(gc->net)))
+		return NULL;
+
+	if (nft_trans_gc_space(gc))
+		return gc;
+
+	set = gc->set;
+	call_rcu(&gc->rcu, nft_trans_gc_trans_free);
+
+	return nft_trans_gc_alloc(set, 0, gfp);
+}
+
+void nft_trans_gc_queue_sync_done(struct nft_trans_gc *trans)
+{
+	WARN_ON_ONCE(!lockdep_commit_lock_is_held(trans->net));
+
+	if (trans->count == 0) {
+		nft_trans_gc_destroy(trans);
+		return;
+	}
+
+	call_rcu(&trans->rcu, nft_trans_gc_trans_free);
+}
+
+struct nft_trans_gc *nft_trans_gc_catchall_async(struct nft_trans_gc *gc,
+						 unsigned int gc_seq)
+{
+	struct nft_set_elem_catchall *catchall;
+	const struct nft_set *set = gc->set;
+	struct nft_set_ext *ext;
+
+	list_for_each_entry_rcu(catchall, &set->catchall_list, list) {
+		ext = nft_set_elem_ext(set, catchall->elem);
+
+		if (!nft_set_elem_expired(ext))
+			continue;
+		if (nft_set_elem_is_dead(ext))
+			goto dead_elem;
+
+		nft_set_elem_dead(ext);
+dead_elem:
+		gc = nft_trans_gc_queue_async(gc, gc_seq, GFP_ATOMIC);
+		if (!gc)
+			return NULL;
+
+		nft_trans_gc_elem_add(gc, catchall->elem);
+	}
+
+	return gc;
+}
+
+struct nft_trans_gc *nft_trans_gc_catchall_sync(struct nft_trans_gc *gc)
+{
+	struct nft_set_elem_catchall *catchall, *next;
+	u64 tstamp = nft_net_tstamp(gc->net);
+	const struct nft_set *set = gc->set;
+	struct nft_set_elem elem;
+	struct nft_set_ext *ext;
+
+	WARN_ON_ONCE(!lockdep_commit_lock_is_held(gc->net));
+
+	list_for_each_entry_safe(catchall, next, &set->catchall_list, list) {
+		ext = nft_set_elem_ext(set, catchall->elem);
+
+		if (!__nft_set_elem_expired(ext, tstamp))
+			continue;
+
+		gc = nft_trans_gc_queue_sync(gc, GFP_KERNEL);
+		if (!gc)
+			return NULL;
+
+		memset(&elem, 0, sizeof(elem));
+		elem.priv = catchall->elem;
+
+		nft_setelem_data_deactivate(gc->net, gc->set, &elem);
+		nft_setelem_catchall_destroy(catchall);
+		nft_trans_gc_elem_add(gc, elem.priv);
 	}
+
+	return gc;
 }
 
 static void nf_tables_module_autoload_cleanup(struct net *net)
@@ -8526,10 +9416,42 @@
 	}
 }
 
+static void nft_set_commit_update(struct list_head *set_update_list)
+{
+	struct nft_set *set, *next;
+
+	list_for_each_entry_safe(set, next, set_update_list, pending_update) {
+		list_del_init(&set->pending_update);
+
+		if (!set->ops->commit || set->dead)
+			continue;
+
+		set->ops->commit(set);
+	}
+}
+
+static unsigned int nft_gc_seq_begin(struct nftables_pernet *nft_net)
+{
+	unsigned int gc_seq;
+
+	/* Bump gc counter, it becomes odd, this is the busy mark. */
+	gc_seq = READ_ONCE(nft_net->gc_seq);
+	WRITE_ONCE(nft_net->gc_seq, ++gc_seq);
+
+	return gc_seq;
+}
+
+static void nft_gc_seq_end(struct nftables_pernet *nft_net, unsigned int gc_seq)
+{
+	WRITE_ONCE(nft_net->gc_seq, ++gc_seq);
+}
+
 static int nf_tables_commit(struct net *net, struct sk_buff *skb)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
 	struct nft_trans *trans, *next;
+	unsigned int base_seq, gc_seq;
+	LIST_HEAD(set_update_list);
 	struct nft_trans_elem *te;
 	struct nft_chain *chain;
 	struct nft_table *table;
@@ -8541,6 +9463,27 @@
 		return 0;
 	}
 
+	list_for_each_entry(trans, &nft_net->binding_list, binding_list) {
+		switch (trans->msg_type) {
+		case NFT_MSG_NEWSET:
+			if (!nft_trans_set_update(trans) &&
+			    nft_set_is_anonymous(nft_trans_set(trans)) &&
+			    !nft_trans_set_bound(trans)) {
+				pr_warn_once("nftables ruleset with unbound set\n");
+				return -EINVAL;
+			}
+			break;
+		case NFT_MSG_NEWCHAIN:
+			if (!nft_trans_chain_update(trans) &&
+			    nft_chain_binding(nft_trans_chain(trans)) &&
+			    !nft_trans_chain_bound(trans)) {
+				pr_warn_once("nftables ruleset with unbound chain\n");
+				return -EINVAL;
+			}
+			break;
+		}
+	}
+
 	/* 0. Validate ruleset, otherwise roll back for error reporting. */
 	if (nf_tables_validate(net) < 0)
 		return -EAGAIN;
@@ -8582,9 +9525,14 @@
 	 * Bump generation counter, invalidate any dump in progress.
 	 * Cannot fail after this point.
 	 */
-	while (++nft_net->base_seq == 0)
+	base_seq = READ_ONCE(nft_net->base_seq);
+	while (++base_seq == 0)
 		;
 
+	WRITE_ONCE(nft_net->base_seq, base_seq);
+
+	gc_seq = nft_gc_seq_begin(nft_net);
+
 	/* step 3. Start new generation, rules_gen_X now in use. */
 	net->nft.gencursor = nft_gencursor_next(net);
 
@@ -8636,6 +9584,9 @@
 			nf_tables_rule_notify(&trans->ctx,
 					      nft_trans_rule(trans),
 					      NFT_MSG_NEWRULE);
+			if (trans->ctx.chain->flags & NFT_CHAIN_HW_OFFLOAD)
+				nft_flow_rule_destroy(nft_trans_flow_rule(trans));
+
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_DELRULE:
@@ -8646,21 +9597,31 @@
 			nft_rule_expr_deactivate(&trans->ctx,
 						 nft_trans_rule(trans),
 						 NFT_TRANS_COMMIT);
+
+			if (trans->ctx.chain->flags & NFT_CHAIN_HW_OFFLOAD)
+				nft_flow_rule_destroy(nft_trans_flow_rule(trans));
 			break;
 		case NFT_MSG_NEWSET:
-			nft_clear(net, nft_trans_set(trans));
-			/* This avoids hitting -EBUSY when deleting the table
-			 * from the transaction.
-			 */
-			if (nft_set_is_anonymous(nft_trans_set(trans)) &&
-			    !list_empty(&nft_trans_set(trans)->bindings))
-				trans->ctx.table->use--;
+			if (nft_trans_set_update(trans)) {
+				struct nft_set *set = nft_trans_set(trans);
 
+				WRITE_ONCE(set->timeout, nft_trans_set_timeout(trans));
+				WRITE_ONCE(set->gc_int, nft_trans_set_gc_int(trans));
+			} else {
+				nft_clear(net, nft_trans_set(trans));
+				/* This avoids hitting -EBUSY when deleting the table
+				 * from the transaction.
+				 */
+				if (nft_set_is_anonymous(nft_trans_set(trans)) &&
+				    !list_empty(&nft_trans_set(trans)->bindings))
+					nft_use_dec(&trans->ctx.table->use);
+			}
 			nf_tables_set_notify(&trans->ctx, nft_trans_set(trans),
 					     NFT_MSG_NEWSET, GFP_KERNEL);
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_DELSET:
+			nft_trans_set(trans)->dead = 1;
 			list_del_rcu(&nft_trans_set(trans)->list);
 			nf_tables_set_notify(&trans->ctx, nft_trans_set(trans),
 					     NFT_MSG_DELSET, GFP_KERNEL);
@@ -8672,6 +9633,11 @@
 			nf_tables_setelem_notify(&trans->ctx, te->set,
 						 &te->elem,
 						 NFT_MSG_NEWSETELEM);
+			if (te->set->ops->commit &&
+			    list_empty(&te->set->pending_update)) {
+				list_add_tail(&te->set->pending_update,
+					      &set_update_list);
+			}
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_DELSETELEM:
@@ -8685,6 +9651,11 @@
 				atomic_dec(&te->set->nelems);
 				te->set->ndeact--;
 			}
+			if (te->set->ops->commit &&
+			    list_empty(&te->set->pending_update)) {
+				list_add_tail(&te->set->pending_update,
+					      &set_update_list);
+			}
 			break;
 		case NFT_MSG_NEWOBJ:
 			if (nft_trans_obj_update(trans)) {
@@ -8726,13 +9697,12 @@
 			break;
 		case NFT_MSG_DELFLOWTABLE:
 			if (nft_trans_flowtable_update(trans)) {
-				nft_flowtable_hooks_del(nft_trans_flowtable(trans),
-							&nft_trans_flowtable_hooks(trans));
 				nf_tables_flowtable_notify(&trans->ctx,
 							   nft_trans_flowtable(trans),
 							   &nft_trans_flowtable_hooks(trans),
 							   NFT_MSG_DELFLOWTABLE);
 				nft_unregister_flowtable_net_hooks(net,
+								   nft_trans_flowtable(trans),
 								   &nft_trans_flowtable_hooks(trans));
 			} else {
 				list_del_rcu(&nft_trans_flowtable(trans)->list);
@@ -8741,15 +9711,20 @@
 							   &nft_trans_flowtable(trans)->hook_list,
 							   NFT_MSG_DELFLOWTABLE);
 				nft_unregister_flowtable_net_hooks(net,
+						nft_trans_flowtable(trans),
 						&nft_trans_flowtable(trans)->hook_list);
 			}
 			break;
 		}
 	}
 
+	nft_set_commit_update(&set_update_list);
+
 	nft_commit_notify(net, NETLINK_CB(skb).portid);
 	nf_tables_gen_notify(net, skb, NFT_MSG_NEWGEN);
 	nf_tables_commit_audit_log(&adl, nft_net->base_seq);
+
+	nft_gc_seq_end(nft_net, gc_seq);
 	nf_tables_commit_release(net);
 
 	return 0;
@@ -8803,16 +9778,31 @@
 	kfree(trans);
 }
 
+static void nft_set_abort_update(struct list_head *set_update_list)
+{
+	struct nft_set *set, *next;
+
+	list_for_each_entry_safe(set, next, set_update_list, pending_update) {
+		list_del_init(&set->pending_update);
+
+		if (!set->ops->abort)
+			continue;
+
+		set->ops->abort(set);
+	}
+}
+
 static int __nf_tables_abort(struct net *net, enum nfnl_abort_action action)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
 	struct nft_trans *trans, *next;
+	LIST_HEAD(set_update_list);
 	struct nft_trans_elem *te;
-	struct nft_hook *hook;
+	int err = 0;
 
 	if (action == NFNL_ABORT_VALIDATE &&
 	    nf_tables_validate(net) < 0)
-		return -EAGAIN;
+		err = -EAGAIN;
 
 	list_for_each_entry_safe_reverse(trans, next, &nft_net->commit_list,
 					 list) {
@@ -8845,11 +9835,11 @@
 				kfree(nft_trans_chain_name(trans));
 				nft_trans_destroy(trans);
 			} else {
-				if (nft_chain_is_bound(trans->ctx.chain)) {
+				if (nft_trans_chain_bound(trans)) {
 					nft_trans_destroy(trans);
 					break;
 				}
-				trans->ctx.table->use--;
+				nft_use_dec_restore(&trans->ctx.table->use);
 				nft_chain_del(trans->ctx.chain);
 				nf_tables_unregister_hook(trans->ctx.net,
 							  trans->ctx.table,
@@ -8857,12 +9847,16 @@
 			}
 			break;
 		case NFT_MSG_DELCHAIN:
-			trans->ctx.table->use++;
+			nft_use_inc_restore(&trans->ctx.table->use);
 			nft_clear(trans->ctx.net, trans->ctx.chain);
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_NEWRULE:
-			trans->ctx.chain->use--;
+			if (nft_trans_rule_bound(trans)) {
+				nft_trans_destroy(trans);
+				break;
+			}
+			nft_use_dec_restore(&trans->ctx.chain->use);
 			list_del_rcu(&nft_trans_rule(trans)->list);
 			nft_rule_expr_deactivate(&trans->ctx,
 						 nft_trans_rule(trans),
@@ -8871,7 +9865,7 @@
 				nft_flow_rule_destroy(nft_trans_flow_rule(trans));
 			break;
 		case NFT_MSG_DELRULE:
-			trans->ctx.chain->use++;
+			nft_use_inc_restore(&trans->ctx.chain->use);
 			nft_clear(trans->ctx.net, nft_trans_rule(trans));
 			nft_rule_expr_activate(&trans->ctx, nft_trans_rule(trans));
 			if (trans->ctx.chain->flags & NFT_CHAIN_HW_OFFLOAD)
@@ -8880,16 +9874,24 @@
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_NEWSET:
-			trans->ctx.table->use--;
+			if (nft_trans_set_update(trans)) {
+				nft_trans_destroy(trans);
+				break;
+			}
+			nft_use_dec_restore(&trans->ctx.table->use);
 			if (nft_trans_set_bound(trans)) {
 				nft_trans_destroy(trans);
 				break;
 			}
+			nft_trans_set(trans)->dead = 1;
 			list_del_rcu(&nft_trans_set(trans)->list);
 			break;
 		case NFT_MSG_DELSET:
-			trans->ctx.table->use++;
+			nft_use_inc_restore(&trans->ctx.table->use);
 			nft_clear(trans->ctx.net, nft_trans_set(trans));
+			if (nft_trans_set(trans)->flags & (NFT_SET_MAP | NFT_SET_OBJECT))
+				nft_map_activate(&trans->ctx, nft_trans_set(trans));
+
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_NEWSETELEM:
@@ -8901,6 +9903,12 @@
 			nft_setelem_remove(net, te->set, &te->elem);
 			if (!nft_setelem_is_catchall(te->set, &te->elem))
 				atomic_dec(&te->set->nelems);
+
+			if (te->set->ops->abort &&
+			    list_empty(&te->set->pending_update)) {
+				list_add_tail(&te->set->pending_update,
+					      &set_update_list);
+			}
 			break;
 		case NFT_MSG_DELSETELEM:
 			te = (struct nft_trans_elem *)trans->data;
@@ -8910,39 +9918,46 @@
 			if (!nft_setelem_is_catchall(te->set, &te->elem))
 				te->set->ndeact--;
 
+			if (te->set->ops->abort &&
+			    list_empty(&te->set->pending_update)) {
+				list_add_tail(&te->set->pending_update,
+					      &set_update_list);
+			}
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_NEWOBJ:
 			if (nft_trans_obj_update(trans)) {
-				kfree(nft_trans_obj_newobj(trans));
+				nft_obj_destroy(&trans->ctx, nft_trans_obj_newobj(trans));
 				nft_trans_destroy(trans);
 			} else {
-				trans->ctx.table->use--;
+				nft_use_dec_restore(&trans->ctx.table->use);
 				nft_obj_del(nft_trans_obj(trans));
 			}
 			break;
 		case NFT_MSG_DELOBJ:
-			trans->ctx.table->use++;
+			nft_use_inc_restore(&trans->ctx.table->use);
 			nft_clear(trans->ctx.net, nft_trans_obj(trans));
 			nft_trans_destroy(trans);
 			break;
 		case NFT_MSG_NEWFLOWTABLE:
 			if (nft_trans_flowtable_update(trans)) {
 				nft_unregister_flowtable_net_hooks(net,
+						nft_trans_flowtable(trans),
 						&nft_trans_flowtable_hooks(trans));
 			} else {
-				trans->ctx.table->use--;
+				nft_use_dec_restore(&trans->ctx.table->use);
 				list_del_rcu(&nft_trans_flowtable(trans)->list);
 				nft_unregister_flowtable_net_hooks(net,
+						nft_trans_flowtable(trans),
 						&nft_trans_flowtable(trans)->hook_list);
 			}
 			break;
 		case NFT_MSG_DELFLOWTABLE:
 			if (nft_trans_flowtable_update(trans)) {
-				list_for_each_entry(hook, &nft_trans_flowtable(trans)->hook_list, list)
-					hook->inactive = false;
+				list_splice(&nft_trans_flowtable_hooks(trans),
+					    &nft_trans_flowtable(trans)->hook_list);
 			} else {
-				trans->ctx.table->use++;
+				nft_use_inc_restore(&trans->ctx.table->use);
 				nft_clear(trans->ctx.net, nft_trans_flowtable(trans));
 			}
 			nft_trans_destroy(trans);
@@ -8950,32 +9965,39 @@
 		}
 	}
 
+	nft_set_abort_update(&set_update_list);
+
 	synchronize_rcu();
 
 	list_for_each_entry_safe_reverse(trans, next,
 					 &nft_net->commit_list, list) {
-		list_del(&trans->list);
+		nft_trans_list_del(trans);
 		nf_tables_abort_release(trans);
 	}
 
-	if (action == NFNL_ABORT_AUTOLOAD)
-		nf_tables_module_autoload(net);
-	else
-		nf_tables_module_autoload_cleanup(net);
-
-	return 0;
-}
-
-static void nf_tables_cleanup(struct net *net)
-{
-	nft_validate_state_update(net, NFT_VALIDATE_SKIP);
+	return err;
 }
 
 static int nf_tables_abort(struct net *net, struct sk_buff *skb,
 			   enum nfnl_abort_action action)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
-	int ret = __nf_tables_abort(net, action);
+	unsigned int gc_seq;
+	int ret;
+
+	gc_seq = nft_gc_seq_begin(nft_net);
+	ret = __nf_tables_abort(net, action);
+	nft_gc_seq_end(nft_net, gc_seq);
+
+	WARN_ON_ONCE(!list_empty(&nft_net->commit_list));
+
+	/* module autoload needs to happen after GC sequence update because it
+	 * temporarily releases and grabs mutex again.
+	 */
+	if (action == NFNL_ABORT_AUTOLOAD)
+		nf_tables_module_autoload(net);
+	else
+		nf_tables_module_autoload_cleanup(net);
 
 	mutex_unlock(&nft_net->commit_mutex);
 
@@ -8988,6 +10010,7 @@
 	bool genid_ok;
 
 	mutex_lock(&nft_net->commit_mutex);
+	nft_net->tstamp = get_jiffies_64();
 
 	genid_ok = genid == 0 || nft_net->base_seq == genid;
 	if (!genid_ok)
@@ -9004,7 +10027,6 @@
 	.cb		= nf_tables_cb,
 	.commit		= nf_tables_commit,
 	.abort		= nf_tables_abort,
-	.cleanup	= nf_tables_cleanup,
 	.valid_genid	= nf_tables_valid_genid,
 	.owner		= THIS_MODULE,
 };
@@ -9041,143 +10063,6 @@
 }
 EXPORT_SYMBOL_GPL(nft_chain_validate_hooks);
 
-/*
- * Loop detection - walk through the ruleset beginning at the destination chain
- * of a new jump until either the source chain is reached (loop) or all
- * reachable chains have been traversed.
- *
- * The loop check is performed whenever a new jump verdict is added to an
- * expression or verdict map or a verdict map is bound to a new chain.
- */
-
-static int nf_tables_check_loops(const struct nft_ctx *ctx,
-				 const struct nft_chain *chain);
-
-static int nft_check_loops(const struct nft_ctx *ctx,
-			   const struct nft_set_ext *ext)
-{
-	const struct nft_data *data;
-	int ret;
-
-	data = nft_set_ext_data(ext);
-	switch (data->verdict.code) {
-	case NFT_JUMP:
-	case NFT_GOTO:
-		ret = nf_tables_check_loops(ctx, data->verdict.chain);
-		break;
-	default:
-		ret = 0;
-		break;
-	}
-
-	return ret;
-}
-
-static int nf_tables_loop_check_setelem(const struct nft_ctx *ctx,
-					struct nft_set *set,
-					const struct nft_set_iter *iter,
-					struct nft_set_elem *elem)
-{
-	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
-
-	if (nft_set_ext_exists(ext, NFT_SET_EXT_FLAGS) &&
-	    *nft_set_ext_flags(ext) & NFT_SET_ELEM_INTERVAL_END)
-		return 0;
-
-	return nft_check_loops(ctx, ext);
-}
-
-static int nft_set_catchall_loops(const struct nft_ctx *ctx,
-				  struct nft_set *set)
-{
-	u8 genmask = nft_genmask_next(ctx->net);
-	struct nft_set_elem_catchall *catchall;
-	struct nft_set_ext *ext;
-	int ret = 0;
-
-	list_for_each_entry_rcu(catchall, &set->catchall_list, list) {
-		ext = nft_set_elem_ext(set, catchall->elem);
-		if (!nft_set_elem_active(ext, genmask))
-			continue;
-
-		ret = nft_check_loops(ctx, ext);
-		if (ret < 0)
-			return ret;
-	}
-
-	return ret;
-}
-
-static int nf_tables_check_loops(const struct nft_ctx *ctx,
-				 const struct nft_chain *chain)
-{
-	const struct nft_rule *rule;
-	const struct nft_expr *expr, *last;
-	struct nft_set *set;
-	struct nft_set_binding *binding;
-	struct nft_set_iter iter;
-
-	if (ctx->chain == chain)
-		return -ELOOP;
-
-	list_for_each_entry(rule, &chain->rules, list) {
-		nft_rule_for_each_expr(expr, last, rule) {
-			struct nft_immediate_expr *priv;
-			const struct nft_data *data;
-			int err;
-
-			if (strcmp(expr->ops->type->name, "immediate"))
-				continue;
-
-			priv = nft_expr_priv(expr);
-			if (priv->dreg != NFT_REG_VERDICT)
-				continue;
-
-			data = &priv->data;
-			switch (data->verdict.code) {
-			case NFT_JUMP:
-			case NFT_GOTO:
-				err = nf_tables_check_loops(ctx,
-							data->verdict.chain);
-				if (err < 0)
-					return err;
-				break;
-			default:
-				break;
-			}
-		}
-	}
-
-	list_for_each_entry(set, &ctx->table->sets, list) {
-		if (!nft_is_active_next(ctx->net, set))
-			continue;
-		if (!(set->flags & NFT_SET_MAP) ||
-		    set->dtype != NFT_DATA_VERDICT)
-			continue;
-
-		list_for_each_entry(binding, &set->bindings, list) {
-			if (!(binding->flags & NFT_SET_MAP) ||
-			    binding->chain != chain)
-				continue;
-
-			iter.genmask	= nft_genmask_next(ctx->net);
-			iter.skip 	= 0;
-			iter.count	= 0;
-			iter.err	= 0;
-			iter.fn		= nf_tables_loop_check_setelem;
-
-			set->ops->walk(ctx, set, &iter);
-			if (!iter.err)
-				iter.err = nft_set_catchall_loops(ctx, set);
-
-			if (iter.err < 0)
-				return iter.err;
-		}
-	}
-
-	return 0;
-}
-
 /**
  *	nft_parse_u32_check - fetch u32 attribute and check for maximum value
  *
@@ -9203,17 +10088,23 @@
 }
 EXPORT_SYMBOL_GPL(nft_parse_u32_check);
 
-static unsigned int nft_parse_register(const struct nlattr *attr)
+static int nft_parse_register(const struct nlattr *attr, u32 *preg)
 {
 	unsigned int reg;
 
 	reg = ntohl(nla_get_be32(attr));
 	switch (reg) {
 	case NFT_REG_VERDICT...NFT_REG_4:
-		return reg * NFT_REG_SIZE / NFT_REG32_SIZE;
+		*preg = reg * NFT_REG_SIZE / NFT_REG32_SIZE;
+		break;
+	case NFT_REG32_00...NFT_REG32_15:
+		*preg = reg + NFT_REG_SIZE / NFT_REG32_SIZE - NFT_REG32_00;
+		break;
 	default:
-		return reg + NFT_REG_SIZE / NFT_REG32_SIZE - NFT_REG32_00;
+		return -ERANGE;
 	}
+
+	return 0;
 }
 
 /**
@@ -9255,7 +10146,10 @@
 	u32 reg;
 	int err;
 
-	reg = nft_parse_register(attr);
+	err = nft_parse_register(attr, &reg);
+	if (err < 0)
+		return err;
+
 	err = nft_validate_register_load(reg, len);
 	if (err < 0)
 		return err;
@@ -9281,13 +10175,16 @@
 		if (data != NULL &&
 		    (data->verdict.code == NFT_GOTO ||
 		     data->verdict.code == NFT_JUMP)) {
-			err = nf_tables_check_loops(ctx, data->verdict.chain);
+			err = nft_chain_validate(ctx, data->verdict.chain);
 			if (err < 0)
 				return err;
 		}
 
 		return 0;
 	default:
+		if (type != NFT_DATA_VALUE)
+			return -EINVAL;
+
 		if (reg < NFT_REG_1 * NFT_REG_SIZE / NFT_REG32_SIZE)
 			return -EINVAL;
 		if (len == 0)
@@ -9296,8 +10193,6 @@
 		    sizeof_field(struct nft_regs, data))
 			return -ERANGE;
 
-		if (data != NULL && type != NFT_DATA_VALUE)
-			return -EINVAL;
 		return 0;
 	}
 }
@@ -9310,7 +10205,10 @@
 	int err;
 	u32 reg;
 
-	reg = nft_parse_register(attr);
+	err = nft_parse_register(attr, &reg);
+	if (err < 0)
+		return err;
+
 	err = nft_validate_register_store(ctx, reg, data, type, len);
 	if (err < 0)
 		return err;
@@ -9342,19 +10240,16 @@
 
 	if (!tb[NFTA_VERDICT_CODE])
 		return -EINVAL;
+
+	/* zero padding hole for memcmp */
+	memset(data, 0, sizeof(*data));
 	data->verdict.code = ntohl(nla_get_be32(tb[NFTA_VERDICT_CODE]));
 
 	switch (data->verdict.code) {
-	default:
-		switch (data->verdict.code & NF_VERDICT_MASK) {
-		case NF_ACCEPT:
-		case NF_DROP:
-		case NF_QUEUE:
-			break;
-		default:
-			return -EINVAL;
-		}
-		fallthrough;
+	case NF_ACCEPT:
+	case NF_DROP:
+	case NF_QUEUE:
+		break;
 	case NFT_CONTINUE:
 	case NFT_BREAK:
 	case NFT_RETURN:
@@ -9366,8 +10261,9 @@
 						 tb[NFTA_VERDICT_CHAIN],
 						 genmask);
 		} else if (tb[NFTA_VERDICT_CHAIN_ID]) {
-			chain = nft_chain_lookup_byid(ctx->net,
-						      tb[NFTA_VERDICT_CHAIN_ID]);
+			chain = nft_chain_lookup_byid(ctx->net, ctx->table,
+						      tb[NFTA_VERDICT_CHAIN_ID],
+						      genmask);
 			if (IS_ERR(chain))
 				return PTR_ERR(chain);
 		} else {
@@ -9378,36 +10274,34 @@
 			return PTR_ERR(chain);
 		if (nft_is_base_chain(chain))
 			return -EOPNOTSUPP;
+		if (nft_chain_is_bound(chain))
+			return -EINVAL;
+		if (desc->flags & NFT_DATA_DESC_SETELEM &&
+		    chain->flags & NFT_CHAIN_BINDING)
+			return -EINVAL;
+		if (!nft_use_inc(&chain->use))
+			return -EMFILE;
 
-		chain->use++;
 		data->verdict.chain = chain;
 		break;
+	default:
+		return -EINVAL;
 	}
 
 	desc->len = sizeof(data->verdict);
-	desc->type = NFT_DATA_VERDICT;
+
 	return 0;
 }
 
 static void nft_verdict_uninit(const struct nft_data *data)
 {
 	struct nft_chain *chain;
-	struct nft_rule *rule;
 
 	switch (data->verdict.code) {
 	case NFT_JUMP:
 	case NFT_GOTO:
 		chain = data->verdict.chain;
-		chain->use--;
-
-		if (!nft_chain_is_bound(chain))
-			break;
-
-		chain->table->use--;
-		list_for_each_entry(rule, &chain->rules, list)
-			chain->use--;
-
-		nft_chain_del(chain);
+		nft_use_dec(&chain->use);
 		break;
 	}
 }
@@ -9438,20 +10332,25 @@
 }
 
 static int nft_value_init(const struct nft_ctx *ctx,
-			  struct nft_data *data, unsigned int size,
-			  struct nft_data_desc *desc, const struct nlattr *nla)
+			  struct nft_data *data, struct nft_data_desc *desc,
+			  const struct nlattr *nla)
 {
 	unsigned int len;
 
 	len = nla_len(nla);
 	if (len == 0)
 		return -EINVAL;
-	if (len > size)
+	if (len > desc->size)
 		return -EOVERFLOW;
+	if (desc->len) {
+		if (len != desc->len)
+			return -EINVAL;
+	} else {
+		desc->len = len;
+	}
 
 	nla_memcpy(data->data, nla, len);
-	desc->type = NFT_DATA_VALUE;
-	desc->len  = len;
+
 	return 0;
 }
 
@@ -9471,7 +10370,6 @@
  *
  *	@ctx: context of the expression using the data
  *	@data: destination struct nft_data
- *	@size: maximum data length
  *	@desc: data description
  *	@nla: netlink attribute containing data
  *
@@ -9481,24 +10379,35 @@
  *	The caller can indicate that it only wants to accept data of type
  *	NFT_DATA_VALUE by passing NULL for the ctx argument.
  */
-int nft_data_init(const struct nft_ctx *ctx,
-		  struct nft_data *data, unsigned int size,
+int nft_data_init(const struct nft_ctx *ctx, struct nft_data *data,
 		  struct nft_data_desc *desc, const struct nlattr *nla)
 {
 	struct nlattr *tb[NFTA_DATA_MAX + 1];
 	int err;
 
+	if (WARN_ON_ONCE(!desc->size))
+		return -EINVAL;
+
 	err = nla_parse_nested_deprecated(tb, NFTA_DATA_MAX, nla,
 					  nft_data_policy, NULL);
 	if (err < 0)
 		return err;
 
-	if (tb[NFTA_DATA_VALUE])
-		return nft_value_init(ctx, data, size, desc,
-				      tb[NFTA_DATA_VALUE]);
-	if (tb[NFTA_DATA_VERDICT] && ctx != NULL)
-		return nft_verdict_init(ctx, data, desc, tb[NFTA_DATA_VERDICT]);
-	return -EINVAL;
+	if (tb[NFTA_DATA_VALUE]) {
+		if (desc->type != NFT_DATA_VALUE)
+			return -EINVAL;
+
+		err = nft_value_init(ctx, data, desc, tb[NFTA_DATA_VALUE]);
+	} else if (tb[NFTA_DATA_VERDICT] && ctx != NULL) {
+		if (desc->type != NFT_DATA_VERDICT)
+			return -EINVAL;
+
+		err = nft_verdict_init(ctx, data, desc, tb[NFTA_DATA_VERDICT]);
+	} else {
+		err = -EINVAL;
+	}
+
+	return err;
 }
 EXPORT_SYMBOL_GPL(nft_data_init);
 
@@ -9561,11 +10470,11 @@
 	nf_tables_unregister_hook(ctx->net, ctx->chain->table, ctx->chain);
 	list_for_each_entry_safe(rule, nr, &ctx->chain->rules, list) {
 		list_del(&rule->list);
-		ctx->chain->use--;
+		nft_use_dec(&ctx->chain->use);
 		nf_tables_rule_release(ctx, rule);
 	}
 	nft_chain_del(ctx->chain);
-	ctx->table->use--;
+	nft_use_dec(&ctx->table->use);
 	nf_tables_chain_destroy(ctx);
 
 	return 0;
@@ -9574,10 +10483,15 @@
 
 static void __nft_release_hook(struct net *net, struct nft_table *table)
 {
+	struct nft_flowtable *flowtable;
 	struct nft_chain *chain;
 
 	list_for_each_entry(chain, &table->chains, list)
-		nf_tables_unregister_hook(net, table, chain);
+		__nf_tables_unregister_hook(net, table, chain, true);
+	list_for_each_entry(flowtable, &table->flowtables, list)
+		__nft_unregister_flowtable_net_hooks(net, flowtable,
+						     &flowtable->hook_list,
+						     true);
 }
 
 static void __nft_release_hooks(struct net *net)
@@ -9608,32 +10522,38 @@
 	ctx.family = table->family;
 	ctx.table = table;
 	list_for_each_entry(chain, &table->chains, list) {
+		if (nft_chain_binding(chain))
+			continue;
+
 		ctx.chain = chain;
 		list_for_each_entry_safe(rule, nr, &chain->rules, list) {
 			list_del(&rule->list);
-			chain->use--;
+			nft_use_dec(&chain->use);
 			nf_tables_rule_release(&ctx, rule);
 		}
 	}
 	list_for_each_entry_safe(flowtable, nf, &table->flowtables, list) {
 		list_del(&flowtable->list);
-		table->use--;
+		nft_use_dec(&table->use);
 		nf_tables_flowtable_destroy(flowtable);
 	}
 	list_for_each_entry_safe(set, ns, &table->sets, list) {
 		list_del(&set->list);
-		table->use--;
+		nft_use_dec(&table->use);
+		if (set->flags & (NFT_SET_MAP | NFT_SET_OBJECT))
+			nft_map_deactivate(&ctx, set);
+
 		nft_set_destroy(&ctx, set);
 	}
 	list_for_each_entry_safe(obj, ne, &table->objects, list) {
 		nft_obj_del(obj);
-		table->use--;
+		nft_use_dec(&table->use);
 		nft_obj_destroy(&ctx, obj);
 	}
 	list_for_each_entry_safe(chain, nc, &table->chains, list) {
 		ctx.chain = chain;
 		nft_chain_del(chain);
-		table->use--;
+		nft_use_dec(&table->use);
 		nf_tables_chain_destroy(&ctx);
 	}
 	nf_tables_table_destroy(&ctx);
@@ -9663,6 +10583,7 @@
 	struct net *net = n->net;
 	unsigned int deleted;
 	bool restart = false;
+	unsigned int gc_seq;
 
 	if (event != NETLINK_URELEASE || n->protocol != NETLINK_NETFILTER)
 		return NOTIFY_DONE;
@@ -9670,6 +10591,10 @@
 	nft_net = nft_pernet(net);
 	deleted = 0;
 	mutex_lock(&nft_net->commit_mutex);
+
+	gc_seq = nft_gc_seq_begin(nft_net);
+
+	nf_tables_trans_destroy_flush_work();
 again:
 	list_for_each_entry(table, &nft_net->tables, list) {
 		if (nft_table_has_owner(table) &&
@@ -9690,6 +10615,8 @@
 		if (restart)
 			goto again;
 	}
+	nft_gc_seq_end(nft_net, gc_seq);
+
 	mutex_unlock(&nft_net->commit_mutex);
 
 	return NOTIFY_DONE;
@@ -9705,10 +10632,12 @@
 
 	INIT_LIST_HEAD(&nft_net->tables);
 	INIT_LIST_HEAD(&nft_net->commit_list);
+	INIT_LIST_HEAD(&nft_net->binding_list);
 	INIT_LIST_HEAD(&nft_net->module_list);
 	INIT_LIST_HEAD(&nft_net->notify_list);
 	mutex_init(&nft_net->commit_mutex);
 	nft_net->base_seq = 1;
+	nft_net->gc_seq = 0;
 	nft_net->validate_state = NFT_VALIDATE_SKIP;
 
 	return 0;
@@ -9716,27 +10645,47 @@
 
 static void __net_exit nf_tables_pre_exit_net(struct net *net)
 {
+	struct nftables_pernet *nft_net = nft_pernet(net);
+
+	mutex_lock(&nft_net->commit_mutex);
 	__nft_release_hooks(net);
+	mutex_unlock(&nft_net->commit_mutex);
 }
 
 static void __net_exit nf_tables_exit_net(struct net *net)
 {
 	struct nftables_pernet *nft_net = nft_pernet(net);
+	unsigned int gc_seq;
 
 	mutex_lock(&nft_net->commit_mutex);
-	if (!list_empty(&nft_net->commit_list))
-		__nf_tables_abort(net, NFNL_ABORT_NONE);
+
+	gc_seq = nft_gc_seq_begin(nft_net);
+
+	WARN_ON_ONCE(!list_empty(&nft_net->commit_list));
+
+	if (!list_empty(&nft_net->module_list))
+		nf_tables_module_autoload_cleanup(net);
+
 	__nft_release_tables(net);
+
+	nft_gc_seq_end(nft_net, gc_seq);
+
 	mutex_unlock(&nft_net->commit_mutex);
 	WARN_ON_ONCE(!list_empty(&nft_net->tables));
 	WARN_ON_ONCE(!list_empty(&nft_net->module_list));
 	WARN_ON_ONCE(!list_empty(&nft_net->notify_list));
 }
 
+static void nf_tables_exit_batch(struct list_head *net_exit_list)
+{
+	flush_work(&trans_gc_work);
+}
+
 static struct pernet_operations nf_tables_net_ops = {
 	.init		= nf_tables_init_net,
 	.pre_exit	= nf_tables_pre_exit_net,
 	.exit		= nf_tables_exit_net,
+	.exit_batch	= nf_tables_exit_batch,
 	.id		= &nf_tables_net_id,
 	.size		= sizeof(struct nftables_pernet),
 };
@@ -9807,7 +10756,9 @@
 	unregister_netdevice_notifier(&nf_tables_flowtable_notifier);
 	nft_chain_filter_fini();
 	nft_chain_route_fini();
+	nf_tables_trans_destroy_flush_work();
 	unregister_pernet_subsys(&nf_tables_net_ops);
+	cancel_work_sync(&trans_gc_work);
 	cancel_work_sync(&trans_destroy_work);
 	rcu_barrier();
 	rhltable_destroy(&nft_objname_ht);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_tables_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_tables_core.c
@@ -67,6 +67,50 @@
 	regs->verdict.code = NFT_BREAK;
 }
 
+static void nft_cmp16_fast_eval(const struct nft_expr *expr,
+				struct nft_regs *regs)
+{
+	const struct nft_cmp16_fast_expr *priv = nft_expr_priv(expr);
+	const u64 *reg_data = (const u64 *)&regs->data[priv->sreg];
+	const u64 *mask = (const u64 *)&priv->mask;
+	const u64 *data = (const u64 *)&priv->data;
+
+	if (((reg_data[0] & mask[0]) == data[0] &&
+	    ((reg_data[1] & mask[1]) == data[1])) ^ priv->inv)
+		return;
+	regs->verdict.code = NFT_BREAK;
+}
+
+static noinline void __nft_trace_verdict(struct nft_traceinfo *info,
+					 const struct nft_chain *chain,
+					 const struct nft_regs *regs)
+{
+	enum nft_trace_types type;
+
+	switch (regs->verdict.code) {
+	case NFT_CONTINUE:
+	case NFT_RETURN:
+		type = NFT_TRACETYPE_RETURN;
+		break;
+	default:
+		type = NFT_TRACETYPE_RULE;
+		break;
+	}
+
+	__nft_trace_packet(info, chain, type);
+}
+
+static inline void nft_trace_verdict(struct nft_traceinfo *info,
+				     const struct nft_chain *chain,
+				     const struct nft_rule *rule,
+				     const struct nft_regs *regs)
+{
+	if (static_branch_unlikely(&nft_trace_enabled)) {
+		info->rule = rule;
+		__nft_trace_verdict(info, chain, regs);
+	}
+}
+
 static bool nft_payload_fast_eval(const struct nft_expr *expr,
 				  struct nft_regs *regs,
 				  const struct nft_pktinfo *pkt)
@@ -79,7 +123,7 @@
 	if (priv->base == NFT_PAYLOAD_NETWORK_HEADER)
 		ptr = skb_network_header(skb);
 	else {
-		if (!pkt->tprot_set)
+		if (!(pkt->flags & NFT_PKTINFO_L4PROTO))
 			return false;
 		ptr = skb_network_header(skb) + nft_thoff(pkt);
 	}
@@ -162,7 +206,7 @@
 	struct nft_rule *const *rules;
 	const struct nft_rule *rule;
 	const struct nft_expr *expr, *last;
-	struct nft_regs regs;
+	struct nft_regs regs = {};
 	unsigned int stackptr = 0;
 	struct nft_jumpstack jumpstack[NFT_JUMP_STACK_SIZE];
 	bool genbit = READ_ONCE(net->nft.gencursor);
@@ -185,6 +229,8 @@
 		nft_rule_for_each_expr(expr, last, rule) {
 			if (expr->ops == &nft_cmp_fast_ops)
 				nft_cmp_fast_eval(expr, &regs);
+			else if (expr->ops == &nft_cmp16_fast_ops)
+				nft_cmp16_fast_eval(expr, &regs);
 			else if (expr->ops == &nft_bitwise_fast_ops)
 				nft_bitwise_fast_eval(expr, &regs);
 			else if (expr->ops != &nft_payload_fast_ops ||
@@ -207,13 +253,13 @@
 		break;
 	}
 
+	nft_trace_verdict(&info, chain, rule, &regs);
+
 	switch (regs.verdict.code & NF_VERDICT_MASK) {
 	case NF_ACCEPT:
 	case NF_DROP:
 	case NF_QUEUE:
 	case NF_STOLEN:
-		nft_trace_packet(&info, chain, rule,
-				 NFT_TRACETYPE_RULE);
 		return regs.verdict.code;
 	}
 
@@ -226,15 +272,10 @@
 		stackptr++;
 		fallthrough;
 	case NFT_GOTO:
-		nft_trace_packet(&info, chain, rule,
-				 NFT_TRACETYPE_RULE);
-
 		chain = regs.verdict.chain;
 		goto do_chain;
 	case NFT_CONTINUE:
 	case NFT_RETURN:
-		nft_trace_packet(&info, chain, rule,
-				 NFT_TRACETYPE_RETURN);
 		break;
 	default:
 		WARN_ON(1);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_tables_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_tables_offload.c
@@ -94,7 +94,8 @@
 
 	expr = nft_expr_first(rule);
 	while (nft_expr_more(rule, expr)) {
-		if (expr->ops->offload_flags & NFT_OFFLOAD_F_ACTION)
+		if (expr->ops->offload_action &&
+		    expr->ops->offload_action(expr))
 			num_actions++;
 
 		expr = nft_expr_next(expr);
@@ -207,7 +208,7 @@
 	return 0;
 }
 
-int nft_chain_offload_priority(struct nft_base_chain *basechain)
+static int nft_chain_offload_priority(const struct nft_base_chain *basechain)
 {
 	if (basechain->ops.priority <= 0 ||
 	    basechain->ops.priority > USHRT_MAX)
@@ -216,6 +217,27 @@
 	return 0;
 }
 
+bool nft_chain_offload_support(const struct nft_base_chain *basechain)
+{
+	struct net_device *dev;
+	struct nft_hook *hook;
+
+	if (nft_chain_offload_priority(basechain) < 0)
+		return false;
+
+	list_for_each_entry(hook, &basechain->hook_list, list) {
+		if (hook->ops.pf != NFPROTO_NETDEV ||
+		    hook->ops.hooknum != NF_NETDEV_INGRESS)
+			return false;
+
+		dev = hook->ops.dev;
+		if (!dev->netdev_ops->ndo_setup_tc && !flow_indr_dev_exists())
+			return false;
+	}
+
+	return true;
+}
+
 static void nft_flow_cls_offload_setup(struct flow_cls_offload *cls_flow,
 				       const struct nft_base_chain *basechain,
 				       const struct nft_rule *rule,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nf_tables_trace.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nf_tables_trace.c
@@ -113,13 +113,13 @@
 	int off = skb_network_offset(skb);
 	unsigned int len, nh_end;
 
-	nh_end = pkt->tprot_set ? nft_thoff(pkt) : skb->len;
+	nh_end = pkt->flags & NFT_PKTINFO_L4PROTO ? nft_thoff(pkt) : skb->len;
 	len = min_t(unsigned int, nh_end - skb_network_offset(skb),
 		    NFT_TRACETYPE_NETWORK_HSIZE);
 	if (trace_fill_header(nlskb, NFTA_TRACE_NETWORK_HEADER, skb, off, len))
 		return -1;
 
-	if (pkt->tprot_set) {
+	if (pkt->flags & NFT_PKTINFO_L4PROTO) {
 		len = min_t(unsigned int, skb->len - nft_thoff(pkt),
 			    NFT_TRACETYPE_TRANSPORT_HSIZE);
 		if (trace_fill_header(nlskb, NFTA_TRACE_TRANSPORT_HEADER, skb,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nfnetlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nfnetlink.c
@@ -290,6 +290,7 @@
 			nfnl_lock(subsys_id);
 			if (nfnl_dereference_protected(subsys_id) != ss ||
 			    nfnetlink_find_client(type, ss) != nc) {
+				nfnl_unlock(subsys_id);
 				err = -EAGAIN;
 				break;
 			}
@@ -527,7 +528,8 @@
 			 * processed, this avoids that the same error is
 			 * reported several times when replaying the batch.
 			 */
-			if (nfnl_err_add(&err_list, nlh, err, &extack) < 0) {
+			if (err == -ENOMEM ||
+			    nfnl_err_add(&err_list, nlh, err, &extack) < 0) {
 				/* We failed to enqueue an error, reset the
 				 * list of errors and send OOM to userspace
 				 * pointing to the batch header.
@@ -584,8 +586,6 @@
 			goto replay_abort;
 		}
 	}
-	if (ss->cleanup)
-		ss->cleanup(net);
 
 	nfnl_err_deliver(&err_list, oskb);
 	kfree_skb(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nfnetlink_hook.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nfnetlink_hook.c
@@ -214,13 +214,6 @@
 		hook_head = rcu_dereference(net->nf.hooks_bridge[hook]);
 #endif
 		break;
-#if IS_ENABLED(CONFIG_DECNET)
-	case NFPROTO_DECNET:
-		if (hook >= ARRAY_SIZE(net->nf.hooks_decnet))
-			return ERR_PTR(-EINVAL);
-		hook_head = rcu_dereference(net->nf.hooks_decnet[hook]);
-		break;
-#endif
 #ifdef CONFIG_NETFILTER_INGRESS
 	case NFPROTO_NETDEV:
 		if (hook != NF_NETDEV_INGRESS)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nfnetlink_log.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nfnetlink_log.c
@@ -556,7 +556,8 @@
 		goto nla_put_failure;
 
 	if (indev && skb->dev &&
-	    skb->mac_header != skb->network_header) {
+	    skb_mac_header_was_set(skb) &&
+	    skb_mac_header_len(skb) != 0) {
 		struct nfulnl_msg_packet_hw phw;
 		int len;
 
@@ -686,8 +687,8 @@
 	unsigned int plen = 0;
 	struct nfnl_log_net *log = nfnl_log_pernet(net);
 	const struct nfnl_ct_hook *nfnl_ct = NULL;
+	enum ip_conntrack_info ctinfo = 0;
 	struct nf_conn *ct = NULL;
-	enum ip_conntrack_info ctinfo;
 
 	if (li_user && li_user->type == NF_LOG_TYPE_ULOG)
 		li = li_user;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nfnetlink_osf.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nfnetlink_osf.c
@@ -269,6 +269,7 @@
 	struct nf_osf_hdr_ctx ctx;
 	const struct tcphdr *tcp;
 	struct tcphdr _tcph;
+	bool found = false;
 
 	memset(&ctx, 0, sizeof(ctx));
 
@@ -283,10 +284,11 @@
 
 		data->genre = f->genre;
 		data->version = f->version;
+		found = true;
 		break;
 	}
 
-	return true;
+	return found;
 }
 EXPORT_SYMBOL_GPL(nf_osf_find);
 
@@ -313,6 +315,14 @@
 
 	f = nla_data(osf_attrs[OSF_ATTR_FINGER]);
 
+	if (f->opt_num > ARRAY_SIZE(f->opt))
+		return -EINVAL;
+
+	if (!memchr(f->genre, 0, MAXGENRELEN) ||
+	    !memchr(f->subtype, 0, MAXGENRELEN) ||
+	    !memchr(f->version, 0, MAXGENRELEN))
+		return -EINVAL;
+
 	kf = kmalloc(sizeof(struct nf_osf_finger), GFP_KERNEL);
 	if (!kf)
 		return -ENOMEM;
@@ -437,3 +447,4 @@
 module_exit(nfnl_osf_fini);
 
 MODULE_LICENSE("GPL");
+MODULE_ALIAS_NFNL_SUBSYS(NFNL_SUBSYS_OSF);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nfnetlink_queue.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nfnetlink_queue.c
@@ -167,7 +167,9 @@
 	struct nfqnl_instance *inst = container_of(head, struct nfqnl_instance,
 						   rcu);
 
+	rcu_read_lock();
 	nfqnl_flush(inst, NULL, 0);
+	rcu_read_unlock();
 	kfree(inst);
 	module_put(THIS_MODULE);
 }
@@ -225,7 +227,7 @@
 
 static void nfqnl_reinject(struct nf_queue_entry *entry, unsigned int verdict)
 {
-	struct nf_ct_hook *ct_hook;
+	const struct nf_ct_hook *ct_hook;
 	int err;
 
 	if (verdict == NF_ACCEPT ||
@@ -301,21 +303,29 @@
 	return -1;
 }
 
-static u32 nfqnl_get_sk_secctx(struct sk_buff *skb, char **secdata)
+static u32 nfqnl_get_sk_secctx(struct sk_buff *skb, struct lsmcontext *context)
 {
-	u32 seclen = 0;
 #if IS_ENABLED(CONFIG_NETWORK_SECMARK)
+	struct lsmblob blob;
+
 	if (!skb || !sk_fullsock(skb->sk))
 		return 0;
 
 	read_lock_bh(&skb->sk->sk_callback_lock);
 
-	if (skb->secmark)
-		security_secid_to_secctx(skb->secmark, secdata, &seclen);
+	if (skb->secmark) {
+		/* lsmblob_init() puts ct->secmark into all of the secids in
+		 * blob. security_secid_to_secctx() will know which security
+		 * module to use to create the secctx.  */
+		lsmblob_init(&blob, skb->secmark);
+		security_secid_to_secctx(&blob, context, LSMBLOB_DISPLAY);
+	}
 
 	read_unlock_bh(&skb->sk->sk_callback_lock);
+	return context->len;
+#else
+	return 0;
 #endif
-	return seclen;
 }
 
 static u32 nfqnl_get_bridge_size(struct nf_queue_entry *entry)
@@ -387,10 +397,10 @@
 	struct net_device *indev;
 	struct net_device *outdev;
 	struct nf_conn *ct = NULL;
-	enum ip_conntrack_info ctinfo;
-	struct nfnl_ct_hook *nfnl_ct;
+	enum ip_conntrack_info ctinfo = 0;
+	const struct nfnl_ct_hook *nfnl_ct;
 	bool csum_verify;
-	char *secdata = NULL;
+	struct lsmcontext context = { };
 	u32 seclen = 0;
 
 	size = nlmsg_total_size(sizeof(struct nfgenmsg))
@@ -459,7 +469,7 @@
 	}
 
 	if ((queue->flags & NFQA_CFG_F_SECCTX) && entskb->sk) {
-		seclen = nfqnl_get_sk_secctx(entskb, &secdata);
+		seclen = nfqnl_get_sk_secctx(entskb, &context);
 		if (seclen)
 			size += nla_total_size(seclen);
 	}
@@ -560,7 +570,8 @@
 		goto nla_put_failure;
 
 	if (indev && entskb->dev &&
-	    entskb->mac_header != entskb->network_header) {
+	    skb_mac_header_was_set(entskb) &&
+	    skb_mac_header_len(entskb) != 0) {
 		struct nfqnl_msg_packet_hw phw;
 		int len;
 
@@ -591,7 +602,7 @@
 	    nfqnl_put_sk_uidgid(skb, entskb->sk) < 0)
 		goto nla_put_failure;
 
-	if (seclen && nla_put(skb, NFQA_SECCTX, seclen, secdata))
+	if (seclen && nla_put(skb, NFQA_SECCTX, context.len, context.context))
 		goto nla_put_failure;
 
 	if (ct && nfnl_ct->build(skb, ct, ctinfo, NFQA_CT, NFQA_CT_INFO) < 0)
@@ -620,7 +631,7 @@
 
 	nlh->nlmsg_len = skb->len;
 	if (seclen)
-		security_release_secctx(secdata, seclen);
+		security_release_secctx(&context);
 	return skb;
 
 nla_put_failure:
@@ -629,7 +640,7 @@
 	net_err_ratelimited("nf_queue: error creating packet message\n");
 nlmsg_failure:
 	if (seclen)
-		security_release_secctx(secdata, seclen);
+		security_release_secctx(&context);
 	return NULL;
 }
 
@@ -637,10 +648,41 @@
 {
 #if IS_ENABLED(CONFIG_NF_CONNTRACK)
 	static const unsigned long flags = IPS_CONFIRMED | IPS_DYING;
-	const struct nf_conn *ct = (void *)skb_nfct(entry->skb);
+	struct nf_conn *ct = (void *)skb_nfct(entry->skb);
+	unsigned long status;
+	unsigned int use;
+
+	if (!ct)
+		return false;
 
-	if (ct && ((ct->status & flags) == IPS_DYING))
+	status = READ_ONCE(ct->status);
+	if ((status & flags) == IPS_DYING)
 		return true;
+
+	if (status & IPS_CONFIRMED)
+		return false;
+
+	/* in some cases skb_clone() can occur after initial conntrack
+	 * pickup, but conntrack assumes exclusive skb->_nfct ownership for
+	 * unconfirmed entries.
+	 *
+	 * This happens for br_netfilter and with ip multicast routing.
+	 * We can't be solved with serialization here because one clone could
+	 * have been queued for local delivery.
+	 */
+	use = refcount_read(&ct->ct_general.use);
+	if (likely(use == 1))
+		return false;
+
+	/* Can't decrement further? Exclusive ownership. */
+	if (!refcount_dec_not_one(&ct->ct_general.use))
+		return false;
+
+	skb_set_nfct(entry->skb, 0);
+	/* No nf_ct_put(): we already decremented .use and it cannot
+	 * drop down to 0.
+	 */
+	return true;
 #endif
 	return false;
 }
@@ -709,9 +751,15 @@
 nf_queue_entry_dup(struct nf_queue_entry *e)
 {
 	struct nf_queue_entry *entry = kmemdup(e, e->size, GFP_ATOMIC);
-	if (entry)
-		nf_queue_entry_get_refs(entry);
-	return entry;
+
+	if (!entry)
+		return NULL;
+
+	if (nf_queue_entry_get_refs(entry))
+		return entry;
+
+	kfree(entry);
+	return NULL;
 }
 
 #if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
@@ -829,11 +877,16 @@
 }
 
 static int
-nfqnl_mangle(void *data, int data_len, struct nf_queue_entry *e, int diff)
+nfqnl_mangle(void *data, unsigned int data_len, struct nf_queue_entry *e, int diff)
 {
 	struct sk_buff *nskb;
 
 	if (diff < 0) {
+		unsigned int min_len = skb_transport_offset(e->skb);
+
+		if (data_len < min_len)
+			return -EINVAL;
+
 		if (pskb_trim(e->skb, data_len))
 			return -ENOMEM;
 	} else if (diff > 0) {
@@ -1103,7 +1156,7 @@
 	return 0;
 }
 
-static struct nf_conn *nfqnl_ct_parse(struct nfnl_ct_hook *nfnl_ct,
+static struct nf_conn *nfqnl_ct_parse(const struct nfnl_ct_hook *nfnl_ct,
 				      const struct nlmsghdr *nlh,
 				      const struct nlattr * const nfqa[],
 				      struct nf_queue_entry *entry,
@@ -1170,11 +1223,11 @@
 {
 	struct nfnl_queue_net *q = nfnl_queue_pernet(info->net);
 	u_int16_t queue_num = ntohs(info->nfmsg->res_id);
+	const struct nfnl_ct_hook *nfnl_ct;
 	struct nfqnl_msg_verdict_hdr *vhdr;
 	enum ip_conntrack_info ctinfo;
 	struct nfqnl_instance *queue;
 	struct nf_queue_entry *entry;
-	struct nfnl_ct_hook *nfnl_ct;
 	struct nf_conn *ct = NULL;
 	unsigned int verdict;
 	int err;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_bitwise.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_bitwise.c
@@ -93,7 +93,16 @@
 static int nft_bitwise_init_bool(struct nft_bitwise *priv,
 				 const struct nlattr *const tb[])
 {
-	struct nft_data_desc mask, xor;
+	struct nft_data_desc mask = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->mask),
+		.len	= priv->len,
+	};
+	struct nft_data_desc xor = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->xor),
+		.len	= priv->len,
+	};
 	int err;
 
 	if (tb[NFTA_BITWISE_DATA])
@@ -103,36 +112,30 @@
 	    !tb[NFTA_BITWISE_XOR])
 		return -EINVAL;
 
-	err = nft_data_init(NULL, &priv->mask, sizeof(priv->mask), &mask,
-			    tb[NFTA_BITWISE_MASK]);
+	err = nft_data_init(NULL, &priv->mask, &mask, tb[NFTA_BITWISE_MASK]);
 	if (err < 0)
 		return err;
-	if (mask.type != NFT_DATA_VALUE || mask.len != priv->len) {
-		err = -EINVAL;
-		goto err1;
-	}
 
-	err = nft_data_init(NULL, &priv->xor, sizeof(priv->xor), &xor,
-			    tb[NFTA_BITWISE_XOR]);
+	err = nft_data_init(NULL, &priv->xor, &xor, tb[NFTA_BITWISE_XOR]);
 	if (err < 0)
-		goto err1;
-	if (xor.type != NFT_DATA_VALUE || xor.len != priv->len) {
-		err = -EINVAL;
-		goto err2;
-	}
+		goto err_xor_err;
 
 	return 0;
-err2:
-	nft_data_release(&priv->xor, xor.type);
-err1:
+
+err_xor_err:
 	nft_data_release(&priv->mask, mask.type);
+
 	return err;
 }
 
 static int nft_bitwise_init_shift(struct nft_bitwise *priv,
 				  const struct nlattr *const tb[])
 {
-	struct nft_data_desc d;
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->data),
+		.len	= sizeof(u32),
+	};
 	int err;
 
 	if (tb[NFTA_BITWISE_MASK] ||
@@ -142,13 +145,12 @@
 	if (!tb[NFTA_BITWISE_DATA])
 		return -EINVAL;
 
-	err = nft_data_init(NULL, &priv->data, sizeof(priv->data), &d,
-			    tb[NFTA_BITWISE_DATA]);
+	err = nft_data_init(NULL, &priv->data, &desc, tb[NFTA_BITWISE_DATA]);
 	if (err < 0)
 		return err;
-	if (d.type != NFT_DATA_VALUE || d.len != sizeof(u32) ||
-	    priv->data.data[0] >= BITS_PER_TYPE(u32)) {
-		nft_data_release(&priv->data, d.type);
+
+	if (priv->data.data[0] >= BITS_PER_TYPE(u32)) {
+		nft_data_release(&priv->data, desc.type);
 		return -EINVAL;
 	}
 
@@ -290,22 +292,21 @@
 static int
 nft_bitwise_extract_u32_data(const struct nlattr * const tb, u32 *out)
 {
-	struct nft_data_desc desc;
 	struct nft_data data;
-	int err = 0;
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(data),
+		.len	= sizeof(u32),
+	};
+	int err;
 
-	err = nft_data_init(NULL, &data, sizeof(data), &desc, tb);
+	err = nft_data_init(NULL, &data, &desc, tb);
 	if (err < 0)
 		return err;
 
-	if (desc.type != NFT_DATA_VALUE || desc.len != sizeof(u32)) {
-		err = -EINVAL;
-		goto err;
-	}
 	*out = data.data[0];
-err:
-	nft_data_release(&data, desc.type);
-	return err;
+
+	return 0;
 }
 
 static int nft_bitwise_fast_init(const struct nft_ctx *ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_byteorder.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_byteorder.c
@@ -30,28 +30,30 @@
 	const struct nft_byteorder *priv = nft_expr_priv(expr);
 	u32 *src = &regs->data[priv->sreg];
 	u32 *dst = &regs->data[priv->dreg];
-	union { u32 u32; u16 u16; } *s, *d;
+	u16 *s16, *d16;
 	unsigned int i;
 
-	s = (void *)src;
-	d = (void *)dst;
+	s16 = (void *)src;
+	d16 = (void *)dst;
 
 	switch (priv->size) {
 	case 8: {
+		u64 *dst64 = (void *)dst;
 		u64 src64;
 
 		switch (priv->op) {
 		case NFT_BYTEORDER_NTOH:
 			for (i = 0; i < priv->len / 8; i++) {
 				src64 = nft_reg_load64(&src[i]);
-				nft_reg_store64(&dst[i], be64_to_cpu(src64));
+				nft_reg_store64(&dst64[i],
+						be64_to_cpu((__force __be64)src64));
 			}
 			break;
 		case NFT_BYTEORDER_HTON:
 			for (i = 0; i < priv->len / 8; i++) {
 				src64 = (__force __u64)
 					cpu_to_be64(nft_reg_load64(&src[i]));
-				nft_reg_store64(&dst[i], src64);
+				nft_reg_store64(&dst64[i], src64);
 			}
 			break;
 		}
@@ -61,11 +63,11 @@
 		switch (priv->op) {
 		case NFT_BYTEORDER_NTOH:
 			for (i = 0; i < priv->len / 4; i++)
-				d[i].u32 = ntohl((__force __be32)s[i].u32);
+				dst[i] = ntohl((__force __be32)src[i]);
 			break;
 		case NFT_BYTEORDER_HTON:
 			for (i = 0; i < priv->len / 4; i++)
-				d[i].u32 = (__force __u32)htonl(s[i].u32);
+				dst[i] = (__force __u32)htonl(src[i]);
 			break;
 		}
 		break;
@@ -73,11 +75,11 @@
 		switch (priv->op) {
 		case NFT_BYTEORDER_NTOH:
 			for (i = 0; i < priv->len / 2; i++)
-				d[i].u16 = ntohs((__force __be16)s[i].u16);
+				d16[i] = ntohs((__force __be16)s16[i]);
 			break;
 		case NFT_BYTEORDER_HTON:
 			for (i = 0; i < priv->len / 2; i++)
-				d[i].u16 = (__force __u16)htons(s[i].u16);
+				d16[i] = (__force __u16)htons(s16[i]);
 			break;
 		}
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_chain_filter.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_chain_filter.c
@@ -336,12 +336,20 @@
 		return;
 
 	if (n > 1) {
-		nf_unregister_net_hook(ctx->net, &found->ops);
+		if (!(ctx->chain->table->flags & NFT_TABLE_F_DORMANT))
+			nf_unregister_net_hook(ctx->net, &found->ops);
+
 		list_del_rcu(&found->list);
 		kfree_rcu(found, rcu);
 		return;
 	}
 
+	/* UNREGISTER events are also happening on netns exit.
+	 *
+	 * Although nf_tables core releases all tables/chains, only this event
+	 * handler provides guarantee that hook->ops.dev is still accessible,
+	 * so we cannot skip exiting net namespaces.
+	 */
 	__nft_release_basechain(ctx);
 }
 
@@ -349,9 +357,10 @@
 				  unsigned long event, void *ptr)
 {
 	struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+	struct nft_base_chain *basechain;
 	struct nftables_pernet *nft_net;
-	struct nft_table *table;
 	struct nft_chain *chain, *nr;
+	struct nft_table *table;
 	struct nft_ctx ctx = {
 		.net	= dev_net(dev),
 	};
@@ -360,13 +369,11 @@
 	    event != NETDEV_CHANGENAME)
 		return NOTIFY_DONE;
 
-	if (!check_net(ctx.net))
-		return NOTIFY_DONE;
-
 	nft_net = nft_pernet(ctx.net);
 	mutex_lock(&nft_net->commit_mutex);
 	list_for_each_entry(table, &nft_net->tables, list) {
-		if (table->family != NFPROTO_NETDEV)
+		if (table->family != NFPROTO_NETDEV &&
+		    table->family != NFPROTO_INET)
 			continue;
 
 		ctx.family = table->family;
@@ -375,6 +382,11 @@
 			if (!nft_is_base_chain(chain))
 				continue;
 
+			basechain = nft_base_chain(chain);
+			if (table->family == NFPROTO_INET &&
+			    basechain->ops.hooknum != NF_INET_INGRESS)
+				continue;
+
 			ctx.chain = chain;
 			nft_netdev_event(event, dev, &ctx);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_cmp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_cmp.c
@@ -73,20 +73,16 @@
 			const struct nlattr * const tb[])
 {
 	struct nft_cmp_expr *priv = nft_expr_priv(expr);
-	struct nft_data_desc desc;
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->data),
+	};
 	int err;
 
-	err = nft_data_init(NULL, &priv->data, sizeof(priv->data), &desc,
-			    tb[NFTA_CMP_DATA]);
+	err = nft_data_init(NULL, &priv->data, &desc, tb[NFTA_CMP_DATA]);
 	if (err < 0)
 		return err;
 
-	if (desc.type != NFT_DATA_VALUE) {
-		err = -EINVAL;
-		nft_data_release(&priv->data, desc.type);
-		return err;
-	}
-
 	err = nft_parse_register_load(tb[NFTA_CMP_SREG], &priv->sreg, desc.len);
 	if (err < 0)
 		return err;
@@ -201,12 +197,14 @@
 			     const struct nlattr * const tb[])
 {
 	struct nft_cmp_fast_expr *priv = nft_expr_priv(expr);
-	struct nft_data_desc desc;
 	struct nft_data data;
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(data),
+	};
 	int err;
 
-	err = nft_data_init(NULL, &data, sizeof(data), &desc,
-			    tb[NFTA_CMP_DATA]);
+	err = nft_data_init(NULL, &data, &desc, tb[NFTA_CMP_DATA]);
 	if (err < 0)
 		return err;
 
@@ -272,12 +270,108 @@
 	.offload	= nft_cmp_fast_offload,
 };
 
+static u32 nft_cmp_mask(u32 bitlen)
+{
+	return (__force u32)cpu_to_le32(~0U >> (sizeof(u32) * BITS_PER_BYTE - bitlen));
+}
+
+static void nft_cmp16_fast_mask(struct nft_data *data, unsigned int bitlen)
+{
+	int len = bitlen / BITS_PER_BYTE;
+	int i, words = len / sizeof(u32);
+
+	for (i = 0; i < words; i++) {
+		data->data[i] = 0xffffffff;
+		bitlen -= sizeof(u32) * BITS_PER_BYTE;
+	}
+
+	if (len % sizeof(u32))
+		data->data[i++] = nft_cmp_mask(bitlen);
+
+	for (; i < 4; i++)
+		data->data[i] = 0;
+}
+
+static int nft_cmp16_fast_init(const struct nft_ctx *ctx,
+			       const struct nft_expr *expr,
+			       const struct nlattr * const tb[])
+{
+	struct nft_cmp16_fast_expr *priv = nft_expr_priv(expr);
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->data),
+	};
+	int err;
+
+	err = nft_data_init(NULL, &priv->data, &desc, tb[NFTA_CMP_DATA]);
+	if (err < 0)
+		return err;
+
+	err = nft_parse_register_load(tb[NFTA_CMP_SREG], &priv->sreg, desc.len);
+	if (err < 0)
+		return err;
+
+	nft_cmp16_fast_mask(&priv->mask, desc.len * BITS_PER_BYTE);
+	priv->inv = ntohl(nla_get_be32(tb[NFTA_CMP_OP])) != NFT_CMP_EQ;
+	priv->len = desc.len;
+
+	return 0;
+}
+
+static int nft_cmp16_fast_offload(struct nft_offload_ctx *ctx,
+				  struct nft_flow_rule *flow,
+				  const struct nft_expr *expr)
+{
+	const struct nft_cmp16_fast_expr *priv = nft_expr_priv(expr);
+	struct nft_cmp_expr cmp = {
+		.data	= priv->data,
+		.sreg	= priv->sreg,
+		.len	= priv->len,
+		.op	= priv->inv ? NFT_CMP_NEQ : NFT_CMP_EQ,
+	};
+
+	return __nft_cmp_offload(ctx, flow, &cmp);
+}
+
+static int nft_cmp16_fast_dump(struct sk_buff *skb, const struct nft_expr *expr)
+{
+	const struct nft_cmp16_fast_expr *priv = nft_expr_priv(expr);
+	enum nft_cmp_ops op = priv->inv ? NFT_CMP_NEQ : NFT_CMP_EQ;
+
+	if (nft_dump_register(skb, NFTA_CMP_SREG, priv->sreg))
+		goto nla_put_failure;
+	if (nla_put_be32(skb, NFTA_CMP_OP, htonl(op)))
+		goto nla_put_failure;
+
+	if (nft_data_dump(skb, NFTA_CMP_DATA, &priv->data,
+			  NFT_DATA_VALUE, priv->len) < 0)
+		goto nla_put_failure;
+	return 0;
+
+nla_put_failure:
+	return -1;
+}
+
+
+const struct nft_expr_ops nft_cmp16_fast_ops = {
+	.type		= &nft_cmp_type,
+	.size		= NFT_EXPR_SIZE(sizeof(struct nft_cmp16_fast_expr)),
+	.eval		= NULL,	/* inlined */
+	.init		= nft_cmp16_fast_init,
+	.dump		= nft_cmp16_fast_dump,
+	.offload	= nft_cmp16_fast_offload,
+};
+
 static const struct nft_expr_ops *
 nft_cmp_select_ops(const struct nft_ctx *ctx, const struct nlattr * const tb[])
 {
-	struct nft_data_desc desc;
 	struct nft_data data;
+	struct nft_data_desc desc = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(data),
+	};
 	enum nft_cmp_ops op;
+	u8 sreg;
 	int err;
 
 	if (tb[NFTA_CMP_SREG] == NULL ||
@@ -298,21 +392,21 @@
 		return ERR_PTR(-EINVAL);
 	}
 
-	err = nft_data_init(NULL, &data, sizeof(data), &desc,
-			    tb[NFTA_CMP_DATA]);
+	err = nft_data_init(NULL, &data, &desc, tb[NFTA_CMP_DATA]);
 	if (err < 0)
 		return ERR_PTR(err);
 
-	if (desc.type != NFT_DATA_VALUE)
-		goto err1;
-
-	if (desc.len <= sizeof(u32) && (op == NFT_CMP_EQ || op == NFT_CMP_NEQ))
-		return &nft_cmp_fast_ops;
+	sreg = ntohl(nla_get_be32(tb[NFTA_CMP_SREG]));
 
+	if (op == NFT_CMP_EQ || op == NFT_CMP_NEQ) {
+		if (desc.len <= sizeof(u32))
+			return &nft_cmp_fast_ops;
+		else if (desc.len <= sizeof(data) &&
+			 ((sreg >= NFT_REG_1 && sreg <= NFT_REG_4) ||
+			  (sreg >= NFT_REG32_00 && sreg <= NFT_REG32_12 && sreg % 2 == 0)))
+			return &nft_cmp16_fast_ops;
+	}
 	return &nft_cmp_ops;
-err1:
-	nft_data_release(&data, desc.type);
-	return ERR_PTR(-EINVAL);
 }
 
 struct nft_expr_type nft_cmp_type __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_compat.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_compat.c
@@ -200,6 +200,7 @@
 static int nft_parse_compat(const struct nlattr *attr, u16 *proto, bool *inv)
 {
 	struct nlattr *tb[NFTA_RULE_COMPAT_MAX+1];
+	u32 l4proto;
 	u32 flags;
 	int err;
 
@@ -212,12 +213,18 @@
 		return -EINVAL;
 
 	flags = ntohl(nla_get_be32(tb[NFTA_RULE_COMPAT_FLAGS]));
-	if (flags & ~NFT_RULE_COMPAT_F_MASK)
+	if (flags & NFT_RULE_COMPAT_F_UNUSED ||
+	    flags & ~NFT_RULE_COMPAT_F_MASK)
 		return -EINVAL;
 	if (flags & NFT_RULE_COMPAT_F_INV)
 		*inv = true;
 
-	*proto = ntohl(nla_get_be32(tb[NFTA_RULE_COMPAT_PROTO]));
+	l4proto = ntohl(nla_get_be32(tb[NFTA_RULE_COMPAT_PROTO]));
+	if (l4proto > U16_MAX)
+		return -EINVAL;
+
+	*proto = l4proto;
+
 	return 0;
 }
 
@@ -349,6 +356,22 @@
 	unsigned int hook_mask = 0;
 	int ret;
 
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET &&
+	    ctx->family != NFPROTO_BRIDGE &&
+	    ctx->family != NFPROTO_ARP)
+		return -EOPNOTSUPP;
+
+	ret = nft_chain_validate_hooks(ctx->chain,
+				       (1 << NF_INET_PRE_ROUTING) |
+				       (1 << NF_INET_LOCAL_IN) |
+				       (1 << NF_INET_FORWARD) |
+				       (1 << NF_INET_LOCAL_OUT) |
+				       (1 << NF_INET_POST_ROUTING));
+	if (ret)
+		return ret;
+
 	if (nft_is_base_chain(ctx->chain)) {
 		const struct nft_base_chain *basechain =
 						nft_base_chain(ctx->chain);
@@ -592,6 +615,22 @@
 	unsigned int hook_mask = 0;
 	int ret;
 
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET &&
+	    ctx->family != NFPROTO_BRIDGE &&
+	    ctx->family != NFPROTO_ARP)
+		return -EOPNOTSUPP;
+
+	ret = nft_chain_validate_hooks(ctx->chain,
+				       (1 << NF_INET_PRE_ROUTING) |
+				       (1 << NF_INET_LOCAL_IN) |
+				       (1 << NF_INET_FORWARD) |
+				       (1 << NF_INET_LOCAL_OUT) |
+				       (1 << NF_INET_POST_ROUTING));
+	if (ret)
+		return ret;
+
 	if (nft_is_base_chain(ctx->chain)) {
 		const struct nft_base_chain *basechain =
 						nft_base_chain(ctx->chain);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_connlimit.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_connlimit.c
@@ -14,7 +14,7 @@
 #include <net/netfilter/nf_conntrack_zones.h>
 
 struct nft_connlimit {
-	struct nf_conncount_list	list;
+	struct nf_conncount_list	*list;
 	u32				limit;
 	bool				invert;
 };
@@ -43,12 +43,12 @@
 		return;
 	}
 
-	if (nf_conncount_add(nft_net(pkt), &priv->list, tuple_ptr, zone)) {
+	if (nf_conncount_add(nft_net(pkt), priv->list, tuple_ptr, zone)) {
 		regs->verdict.code = NF_DROP;
 		return;
 	}
 
-	count = priv->list.count;
+	count = priv->list->count;
 
 	if ((count > priv->limit) ^ priv->invert) {
 		regs->verdict.code = NFT_BREAK;
@@ -62,6 +62,7 @@
 {
 	bool invert = false;
 	u32 flags, limit;
+	int err;
 
 	if (!tb[NFTA_CONNLIMIT_COUNT])
 		return -EINVAL;
@@ -76,18 +77,31 @@
 			invert = true;
 	}
 
-	nf_conncount_list_init(&priv->list);
+	priv->list = kmalloc(sizeof(*priv->list), GFP_KERNEL_ACCOUNT);
+	if (!priv->list)
+		return -ENOMEM;
+
+	nf_conncount_list_init(priv->list);
 	priv->limit	= limit;
 	priv->invert	= invert;
 
-	return nf_ct_netns_get(ctx->net, ctx->family);
+	err = nf_ct_netns_get(ctx->net, ctx->family);
+	if (err < 0)
+		goto err_netns;
+
+	return 0;
+err_netns:
+	kfree(priv->list);
+
+	return err;
 }
 
 static void nft_connlimit_do_destroy(const struct nft_ctx *ctx,
 				     struct nft_connlimit *priv)
 {
 	nf_ct_netns_put(ctx->net, ctx->family);
-	nf_conncount_cache_free(&priv->list);
+	nf_conncount_cache_free(priv->list);
+	kfree(priv->list);
 }
 
 static int nft_connlimit_do_dump(struct sk_buff *skb,
@@ -195,12 +209,16 @@
 	nft_connlimit_do_destroy(ctx, priv);
 }
 
-static int nft_connlimit_clone(struct nft_expr *dst, const struct nft_expr *src)
+static int nft_connlimit_clone(struct nft_expr *dst, const struct nft_expr *src, gfp_t gfp)
 {
 	struct nft_connlimit *priv_dst = nft_expr_priv(dst);
 	struct nft_connlimit *priv_src = nft_expr_priv(src);
 
-	nf_conncount_list_init(&priv_dst->list);
+	priv_dst->list = kmalloc(sizeof(*priv_dst->list), gfp);
+	if (!priv_dst->list)
+		return -ENOMEM;
+
+	nf_conncount_list_init(priv_dst->list);
 	priv_dst->limit	 = priv_src->limit;
 	priv_dst->invert = priv_src->invert;
 
@@ -212,7 +230,8 @@
 {
 	struct nft_connlimit *priv = nft_expr_priv(expr);
 
-	nf_conncount_cache_free(&priv->list);
+	nf_conncount_cache_free(priv->list);
+	kfree(priv->list);
 }
 
 static bool nft_connlimit_gc(struct net *net, const struct nft_expr *expr)
@@ -221,7 +240,7 @@
 	bool ret;
 
 	local_bh_disable();
-	ret = nf_conncount_gc_list(net, &priv->list);
+	ret = nf_conncount_gc_list(net, priv->list);
 	local_bh_enable();
 
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_counter.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_counter.c
@@ -61,7 +61,7 @@
 	struct nft_counter __percpu *cpu_stats;
 	struct nft_counter *this_cpu;
 
-	cpu_stats = alloc_percpu(struct nft_counter);
+	cpu_stats = alloc_percpu_gfp(struct nft_counter, GFP_KERNEL_ACCOUNT);
 	if (cpu_stats == NULL)
 		return -ENOMEM;
 
@@ -106,11 +106,16 @@
 			      struct nft_counter *total)
 {
 	struct nft_counter *this_cpu;
+	seqcount_t *myseq;
 
 	local_bh_disable();
 	this_cpu = this_cpu_ptr(priv->counter);
+	myseq = this_cpu_ptr(&nft_counter_seq);
+
+	write_seqcount_begin(myseq);
 	this_cpu->packets -= total->packets;
 	this_cpu->bytes -= total->bytes;
+	write_seqcount_end(myseq);
 	local_bh_enable();
 }
 
@@ -225,7 +230,7 @@
 	nft_counter_do_destroy(priv);
 }
 
-static int nft_counter_clone(struct nft_expr *dst, const struct nft_expr *src)
+static int nft_counter_clone(struct nft_expr *dst, const struct nft_expr *src, gfp_t gfp)
 {
 	struct nft_counter_percpu_priv *priv = nft_expr_priv(src);
 	struct nft_counter_percpu_priv *priv_clone = nft_expr_priv(dst);
@@ -235,7 +240,7 @@
 
 	nft_counter_fetch(priv, &total);
 
-	cpu_stats = alloc_percpu_gfp(struct nft_counter, GFP_ATOMIC);
+	cpu_stats = alloc_percpu_gfp(struct nft_counter, gfp);
 	if (cpu_stats == NULL)
 		return -ENOMEM;
 
@@ -264,7 +269,7 @@
 	struct nft_counter *this_cpu;
 	seqcount_t *myseq;
 
-	preempt_disable();
+	local_bh_disable();
 	this_cpu = this_cpu_ptr(priv->counter);
 	myseq = this_cpu_ptr(&nft_counter_seq);
 
@@ -272,7 +277,7 @@
 	this_cpu->packets += stats->pkts;
 	this_cpu->bytes += stats->bytes;
 	write_seqcount_end(myseq);
-	preempt_enable();
+	local_bh_enable();
 }
 
 static struct nft_expr_type nft_counter_type;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_ct.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_ct.c
@@ -97,7 +97,7 @@
 		return;
 #ifdef CONFIG_NF_CONNTRACK_MARK
 	case NFT_CT_MARK:
-		*dest = ct->mark;
+		*dest = READ_ONCE(ct->mark);
 		return;
 #endif
 #ifdef CONFIG_NF_CONNTRACK_SECMARK
@@ -239,6 +239,7 @@
 	enum ip_conntrack_info ctinfo;
 	u16 value = nft_reg_load16(&regs->data[priv->sreg]);
 	struct nf_conn *ct;
+	int oldcnt;
 
 	ct = nf_ct_get(skb, &ctinfo);
 	if (ct) /* already tracked */
@@ -259,18 +260,22 @@
 
 	ct = this_cpu_read(nft_ct_pcpu_template);
 
-	if (likely(atomic_read(&ct->ct_general.use) == 1)) {
+	__refcount_inc(&ct->ct_general.use, &oldcnt);
+	if (likely(oldcnt == 1)) {
 		nf_ct_zone_add(ct, &zone);
 	} else {
-		/* previous skb got queued to userspace */
+		refcount_dec(&ct->ct_general.use);
+		/* previous skb got queued to userspace, allocate temporary
+		 * one until percpu template can be reused.
+		 */
 		ct = nf_ct_tmpl_alloc(nft_net(pkt), &zone, GFP_ATOMIC);
 		if (!ct) {
 			regs->verdict.code = NF_DROP;
 			return;
 		}
+		__set_bit(IPS_CONFIRMED_BIT, &ct->status);
 	}
 
-	atomic_inc(&ct->ct_general.use);
 	nf_ct_set(skb, ct, IP_CT_NEW);
 }
 #endif
@@ -294,8 +299,8 @@
 	switch (priv->key) {
 #ifdef CONFIG_NF_CONNTRACK_MARK
 	case NFT_CT_MARK:
-		if (ct->mark != value) {
-			ct->mark = value;
+		if (READ_ONCE(ct->mark) != value) {
+			WRITE_ONCE(ct->mark, value);
 			nf_conntrack_event_cache(IPCT_MARK, ct);
 		}
 		break;
@@ -375,7 +380,7 @@
 			return false;
 		}
 
-		atomic_set(&tmp->ct_general.use, 1);
+		__set_bit(IPS_CONFIRMED_BIT, &tmp->status);
 		per_cpu(nft_ct_pcpu_template, cpu) = tmp;
 	}
 
@@ -482,6 +487,9 @@
 		break;
 #endif
 	case NFT_CT_ID:
+		if (tb[NFTA_CT_DIRECTION])
+			return -EINVAL;
+
 		len = sizeof(u32);
 		break;
 	default:
@@ -1040,6 +1048,9 @@
 	if (err < 0)
 		goto err_put_helper;
 
+	/* Avoid the bogus warning, helper will be assigned after CT init */
+	nf_ct_set_auto_assign_helper_warned(ctx->net);
+
 	return 0;
 
 err_put_helper:
@@ -1182,7 +1193,30 @@
 	if (tb[NFTA_CT_EXPECT_L3PROTO])
 		priv->l3num = ntohs(nla_get_be16(tb[NFTA_CT_EXPECT_L3PROTO]));
 
+	switch (priv->l3num) {
+	case NFPROTO_IPV4:
+	case NFPROTO_IPV6:
+		if (priv->l3num == ctx->family || ctx->family == NFPROTO_INET)
+			break;
+
+		return -EINVAL;
+	case NFPROTO_INET: /* tuple.src.l3num supports NFPROTO_IPV4/6 only */
+	default:
+		return -EAFNOSUPPORT;
+	}
+
 	priv->l4proto = nla_get_u8(tb[NFTA_CT_EXPECT_L4PROTO]);
+	switch (priv->l4proto) {
+	case IPPROTO_TCP:
+	case IPPROTO_UDP:
+	case IPPROTO_UDPLITE:
+	case IPPROTO_DCCP:
+	case IPPROTO_SCTP:
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
 	priv->dport = nla_get_be16(tb[NFTA_CT_EXPECT_DPORT]);
 	priv->timeout = nla_get_u32(tb[NFTA_CT_EXPECT_TIMEOUT]);
 	priv->size = nla_get_u8(tb[NFTA_CT_EXPECT_SIZE]);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_dup_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_dup_netdev.c
@@ -67,6 +67,11 @@
 	return nft_fwd_dup_netdev_offload(ctx, flow, FLOW_ACTION_MIRRED, oif);
 }
 
+static bool nft_dup_netdev_offload_action(const struct nft_expr *expr)
+{
+	return true;
+}
+
 static struct nft_expr_type nft_dup_netdev_type;
 static const struct nft_expr_ops nft_dup_netdev_ops = {
 	.type		= &nft_dup_netdev_type,
@@ -75,6 +80,7 @@
 	.init		= nft_dup_netdev_init,
 	.dump		= nft_dup_netdev_dump,
 	.offload	= nft_dup_netdev_offload,
+	.offload_action	= nft_dup_netdev_offload_action,
 };
 
 static struct nft_expr_type nft_dup_netdev_type __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_dynset.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_dynset.c
@@ -35,7 +35,7 @@
 
 	for (i = 0; i < priv->num_exprs; i++) {
 		expr = nft_setelem_expr_at(elem_expr, elem_expr->size);
-		if (nft_expr_clone(expr, priv->expr_array[i]) < 0)
+		if (nft_expr_clone(expr, priv->expr_array[i], GFP_ATOMIC) < 0)
 			return -1;
 
 		elem_expr->size += priv->expr_array[i]->ops->size;
@@ -191,6 +191,9 @@
 	if (IS_ERR(set))
 		return PTR_ERR(set);
 
+	if (set->flags & NFT_SET_OBJECT)
+		return -EOPNOTSUPP;
+
 	if (set->ops->update == NULL)
 		return -EOPNOTSUPP;
 
@@ -198,17 +201,8 @@
 		return -EBUSY;
 
 	priv->op = ntohl(nla_get_be32(tb[NFTA_DYNSET_OP]));
-	switch (priv->op) {
-	case NFT_DYNSET_OP_ADD:
-	case NFT_DYNSET_OP_DELETE:
-		break;
-	case NFT_DYNSET_OP_UPDATE:
-		if (!(set->flags & NFT_SET_TIMEOUT))
-			return -EOPNOTSUPP;
-		break;
-	default:
+	if (priv->op > NFT_DYNSET_OP_DELETE)
 		return -EOPNOTSUPP;
-	}
 
 	timeout = 0;
 	if (tb[NFTA_DYNSET_TIMEOUT] != NULL) {
@@ -285,10 +279,15 @@
 			priv->expr_array[i] = dynset_expr;
 			priv->num_exprs++;
 
-			if (set->num_exprs &&
-			    dynset_expr->ops != set->exprs[i]->ops) {
-				err = -EOPNOTSUPP;
-				goto err_expr_free;
+			if (set->num_exprs) {
+				if (i >= set->num_exprs) {
+					err = -EINVAL;
+					goto err_expr_free;
+				}
+				if (dynset_expr->ops != set->exprs[i]->ops) {
+					err = -EOPNOTSUPP;
+					goto err_expr_free;
+				}
 			}
 			i++;
 		}
@@ -351,7 +350,7 @@
 {
 	struct nft_dynset *priv = nft_expr_priv(expr);
 
-	priv->set->use++;
+	nf_tables_activate_set(ctx, priv->set);
 }
 
 static void nft_dynset_destroy(const struct nft_ctx *ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_exthdr.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_exthdr.c
@@ -35,6 +35,14 @@
 		return opt[offset + 1];
 }
 
+static int nft_skb_copy_to_reg(const struct sk_buff *skb, int offset, u32 *dest, unsigned int len)
+{
+	if (len % NFT_REG32_SIZE)
+		dest[len / NFT_REG32_SIZE] = 0;
+
+	return skb_copy_bits(skb, offset, dest, len);
+}
+
 static void nft_exthdr_ipv6_eval(const struct nft_expr *expr,
 				 struct nft_regs *regs,
 				 const struct nft_pktinfo *pkt)
@@ -56,8 +64,7 @@
 	}
 	offset += priv->offset;
 
-	dest[priv->len / NFT_REG32_SIZE] = 0;
-	if (skb_copy_bits(pkt->skb, offset, dest, priv->len) < 0)
+	if (nft_skb_copy_to_reg(pkt->skb, offset, dest, priv->len) < 0)
 		goto err;
 	return;
 err:
@@ -78,7 +85,6 @@
 	unsigned char optbuf[sizeof(struct ip_options) + 40];
 	struct ip_options *opt = (struct ip_options *)optbuf;
 	struct iphdr *iph, _iph;
-	unsigned int start;
 	bool found = false;
 	__be32 info;
 	int optlen;
@@ -86,7 +92,6 @@
 	iph = skb_header_pointer(skb, 0, sizeof(_iph), &_iph);
 	if (!iph)
 		return -EBADMSG;
-	start = sizeof(struct iphdr);
 
 	optlen = iph->ihl * 4 - (int)sizeof(struct iphdr);
 	if (optlen <= 0)
@@ -96,7 +101,7 @@
 	/* Copy the options since __ip_options_compile() modifies
 	 * the options.
 	 */
-	if (skb_copy_bits(skb, start, opt->__data, optlen))
+	if (skb_copy_bits(skb, sizeof(struct iphdr), opt->__data, optlen))
 		return -EBADMSG;
 	opt->optlen = optlen;
 
@@ -111,18 +116,18 @@
 		found = target == IPOPT_SSRR ? opt->is_strictroute :
 					       !opt->is_strictroute;
 		if (found)
-			*offset = opt->srr + start;
+			*offset = opt->srr;
 		break;
 	case IPOPT_RR:
 		if (!opt->rr)
 			break;
-		*offset = opt->rr + start;
+		*offset = opt->rr;
 		found = true;
 		break;
 	case IPOPT_RA:
 		if (!opt->router_alert)
 			break;
-		*offset = opt->router_alert + start;
+		*offset = opt->router_alert;
 		found = true;
 		break;
 	default:
@@ -153,8 +158,7 @@
 	}
 	offset += priv->offset;
 
-	dest[priv->len / NFT_REG32_SIZE] = 0;
-	if (skb_copy_bits(pkt->skb, offset, dest, priv->len) < 0)
+	if (nft_skb_copy_to_reg(pkt->skb, offset, dest, priv->len) < 0)
 		goto err;
 	return;
 err:
@@ -167,7 +171,7 @@
 {
 	struct tcphdr *tcph;
 
-	if (pkt->tprot != IPPROTO_TCP)
+	if (pkt->tprot != IPPROTO_TCP || pkt->fragoff)
 		return NULL;
 
 	tcph = skb_header_pointer(pkt->skb, nft_thoff(pkt), sizeof(*tcph), buffer);
@@ -208,9 +212,10 @@
 
 		offset = i + priv->offset;
 		if (priv->flags & NFT_EXTHDR_F_PRESENT) {
-			*dest = 1;
+			nft_reg_store8(dest, 1);
 		} else {
-			dest[priv->len / NFT_REG32_SIZE] = 0;
+			if (priv->len % NFT_REG32_SIZE)
+				dest[priv->len / NFT_REG32_SIZE] = 0;
 			memcpy(dest, opt + offset, priv->len);
 		}
 
@@ -236,9 +241,14 @@
 
 	tcph = nft_tcp_header_pointer(pkt, sizeof(buff), buff, &tcphdr_len);
 	if (!tcph)
-		return;
+		goto err;
+
+	if (skb_ensure_writable(pkt->skb, nft_thoff(pkt) + tcphdr_len))
+		goto err;
 
+	tcph = (struct tcphdr *)(pkt->skb->data + nft_thoff(pkt));
 	opt = (u8 *)tcph;
+
 	for (i = sizeof(*tcph); i < tcphdr_len - 1; i += optl) {
 		union {
 			__be16 v16;
@@ -251,16 +261,7 @@
 			continue;
 
 		if (i + optl > tcphdr_len || priv->len + priv->offset > optl)
-			return;
-
-		if (skb_ensure_writable(pkt->skb,
-					nft_thoff(pkt) + i + priv->len))
-			return;
-
-		tcph = nft_tcp_header_pointer(pkt, sizeof(buff), buff,
-					      &tcphdr_len);
-		if (!tcph)
-			return;
+			goto err;
 
 		offset = i + priv->offset;
 
@@ -303,6 +304,66 @@
 
 		return;
 	}
+	return;
+err:
+	regs->verdict.code = NFT_BREAK;
+}
+
+static void nft_exthdr_tcp_strip_eval(const struct nft_expr *expr,
+				      struct nft_regs *regs,
+				      const struct nft_pktinfo *pkt)
+{
+	u8 buff[sizeof(struct tcphdr) + MAX_TCP_OPTION_SPACE];
+	struct nft_exthdr *priv = nft_expr_priv(expr);
+	unsigned int i, tcphdr_len, optl;
+	struct tcphdr *tcph;
+	u8 *opt;
+
+	tcph = nft_tcp_header_pointer(pkt, sizeof(buff), buff, &tcphdr_len);
+	if (!tcph)
+		goto err;
+
+	if (skb_ensure_writable(pkt->skb, nft_thoff(pkt) + tcphdr_len))
+		goto drop;
+
+	tcph = (struct tcphdr *)(pkt->skb->data + nft_thoff(pkt));
+	opt = (u8 *)tcph;
+
+	for (i = sizeof(*tcph); i < tcphdr_len - 1; i += optl) {
+		unsigned int j;
+
+		optl = optlen(opt, i);
+		if (priv->type != opt[i])
+			continue;
+
+		if (i + optl > tcphdr_len)
+			goto drop;
+
+		for (j = 0; j < optl; ++j) {
+			u16 n = TCPOPT_NOP;
+			u16 o = opt[i+j];
+
+			if ((i + j) % 2 == 0) {
+				o <<= 8;
+				n <<= 8;
+			}
+			inet_proto_csum_replace2(&tcph->check, pkt->skb, htons(o),
+						 htons(n), false);
+		}
+		memset(opt + i, TCPOPT_NOP, optl);
+		return;
+	}
+
+	/* option not found, continue. This allows to do multiple
+	 * option removals per rule.
+	 */
+	return;
+err:
+	regs->verdict.code = NFT_BREAK;
+	return;
+drop:
+	/* can't remove, no choice but to drop */
+	regs->verdict.code = NF_DROP;
 }
 
 static void nft_exthdr_sctp_eval(const struct nft_expr *expr,
@@ -332,9 +393,8 @@
 			    offset + ntohs(sch->length) > pkt->skb->len)
 				break;
 
-			dest[priv->len / NFT_REG32_SIZE] = 0;
-			if (skb_copy_bits(pkt->skb, offset + priv->offset,
-					  dest, priv->len) < 0)
+			if (nft_skb_copy_to_reg(pkt->skb, offset + priv->offset,
+						dest, priv->len) < 0)
 				break;
 			return;
 		}
@@ -454,6 +514,28 @@
 				       priv->len);
 }
 
+static int nft_exthdr_tcp_strip_init(const struct nft_ctx *ctx,
+				     const struct nft_expr *expr,
+				     const struct nlattr * const tb[])
+{
+	struct nft_exthdr *priv = nft_expr_priv(expr);
+
+	if (tb[NFTA_EXTHDR_SREG] ||
+	    tb[NFTA_EXTHDR_DREG] ||
+	    tb[NFTA_EXTHDR_FLAGS] ||
+	    tb[NFTA_EXTHDR_OFFSET] ||
+	    tb[NFTA_EXTHDR_LEN])
+		return -EINVAL;
+
+	if (!tb[NFTA_EXTHDR_TYPE])
+		return -EINVAL;
+
+	priv->type = nla_get_u8(tb[NFTA_EXTHDR_TYPE]);
+	priv->op = NFT_EXTHDR_OP_TCPOPT;
+
+	return 0;
+}
+
 static int nft_exthdr_ipv4_init(const struct nft_ctx *ctx,
 				const struct nft_expr *expr,
 				const struct nlattr * const tb[])
@@ -514,6 +596,13 @@
 	return nft_exthdr_dump_common(skb, priv);
 }
 
+static int nft_exthdr_dump_strip(struct sk_buff *skb, const struct nft_expr *expr)
+{
+	const struct nft_exthdr *priv = nft_expr_priv(expr);
+
+	return nft_exthdr_dump_common(skb, priv);
+}
+
 static const struct nft_expr_ops nft_exthdr_ipv6_ops = {
 	.type		= &nft_exthdr_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_exthdr)),
@@ -546,6 +635,14 @@
 	.dump		= nft_exthdr_dump_set,
 };
 
+static const struct nft_expr_ops nft_exthdr_tcp_strip_ops = {
+	.type		= &nft_exthdr_type,
+	.size		= NFT_EXPR_SIZE(sizeof(struct nft_exthdr)),
+	.eval		= nft_exthdr_tcp_strip_eval,
+	.init		= nft_exthdr_tcp_strip_init,
+	.dump		= nft_exthdr_dump_strip,
+};
+
 static const struct nft_expr_ops nft_exthdr_sctp_ops = {
 	.type		= &nft_exthdr_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_exthdr)),
@@ -573,7 +670,7 @@
 			return &nft_exthdr_tcp_set_ops;
 		if (tb[NFTA_EXTHDR_DREG])
 			return &nft_exthdr_tcp_ops;
-		break;
+		return &nft_exthdr_tcp_strip_ops;
 	case NFT_EXTHDR_OP_IPV6:
 		if (tb[NFTA_EXTHDR_DREG])
 			return &nft_exthdr_ipv6_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_fib.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_fib.c
@@ -140,11 +140,15 @@
 	switch (priv->result) {
 	case NFT_FIB_RESULT_OIF:
 		index = dev ? dev->ifindex : 0;
-		*dreg = (priv->flags & NFTA_FIB_F_PRESENT) ? !!index : index;
+		if (priv->flags & NFTA_FIB_F_PRESENT)
+			nft_reg_store8(dreg, !!index);
+		else
+			*dreg = index;
+
 		break;
 	case NFT_FIB_RESULT_OIFNAME:
 		if (priv->flags & NFTA_FIB_F_PRESENT)
-			*dreg = !!dev;
+			nft_reg_store8(dreg, !!dev);
 		else
 			strncpy(reg, dev ? dev->name : "", IFNAMSIZ);
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_flow_offload.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_flow_offload.c
@@ -36,6 +36,15 @@
 	route->tuple[dir].xmit_type	= nft_xmit_type(dst_cache);
 }
 
+static bool nft_is_valid_ether_device(const struct net_device *dev)
+{
+	if (!dev || (dev->flags & IFF_LOOPBACK) || dev->type != ARPHRD_ETHER ||
+	    dev->addr_len != ETH_ALEN || !is_valid_ether_addr(dev->dev_addr))
+		return false;
+
+	return true;
+}
+
 static int nft_dev_fill_forward_path(const struct nf_flow_route *route,
 				     const struct dst_entry *dst_cache,
 				     const struct nf_conn *ct,
@@ -47,6 +56,9 @@
 	struct neighbour *n;
 	u8 nud_state;
 
+	if (!nft_is_valid_ether_device(dev))
+		goto out;
+
 	n = dst_neigh_lookup(dst_cache, daddr);
 	if (!n)
 		return -1;
@@ -60,6 +72,7 @@
 	if (!(nud_state & NUD_VALID))
 		return -1;
 
+out:
 	return dev_fill_forward_path(dev, ha, stack);
 }
 
@@ -78,15 +91,6 @@
 	enum flow_offload_xmit_type xmit_type;
 };
 
-static bool nft_is_valid_ether_device(const struct net_device *dev)
-{
-	if (!dev || (dev->flags & IFF_LOOPBACK) || dev->type != ARPHRD_ETHER ||
-	    dev->addr_len != ETH_ALEN || !is_valid_ether_addr(dev->dev_addr))
-		return false;
-
-	return true;
-}
-
 static void nft_dev_path_info(const struct net_device_path_stack *stack,
 			      struct nft_forward_info *info,
 			      unsigned char *ha, struct nf_flowtable *flowtable)
@@ -119,7 +123,8 @@
 				info->indev = NULL;
 				break;
 			}
-			info->outdev = path->dev;
+			if (!info->outdev)
+				info->outdev = path->dev;
 			info->encap[info->num_encaps].id = path->encap.id;
 			info->encap[info->num_encaps].proto = path->encap.proto;
 			info->num_encaps++;
@@ -235,9 +240,14 @@
 		break;
 	}
 
+	if (!dst_hold_safe(this_dst))
+		return -ENOENT;
+
 	nf_route(nft_net(pkt), &other_dst, &fl, false, nft_pf(pkt));
-	if (!other_dst)
+	if (!other_dst) {
+		dst_release(this_dst);
 		return -ENOENT;
+	}
 
 	nft_default_forward_path(route, this_dst, dir);
 	nft_default_forward_path(route, other_dst, !dir);
@@ -268,6 +278,15 @@
 	return false;
 }
 
+static void flow_offload_ct_tcp(struct nf_conn *ct)
+{
+	/* conntrack will not see all packets, disable tcp window validation. */
+	spin_lock_bh(&ct->lock);
+	ct->proto.tcp.seen[0].flags |= IP_CT_TCP_FLAG_BE_LIBERAL;
+	ct->proto.tcp.seen[1].flags |= IP_CT_TCP_FLAG_BE_LIBERAL;
+	spin_unlock_bh(&ct->lock);
+}
+
 static void nft_flow_offload_eval(const struct nft_expr *expr,
 				  struct nft_regs *regs,
 				  const struct nft_pktinfo *pkt)
@@ -293,7 +312,8 @@
 	case IPPROTO_TCP:
 		tcph = skb_header_pointer(pkt->skb, nft_thoff(pkt),
 					  sizeof(_tcph), &_tcph);
-		if (unlikely(!tcph || tcph->fin || tcph->rst))
+		if (unlikely(!tcph || tcph->fin || tcph->rst ||
+			     !nf_conntrack_tcp_established(ct)))
 			goto out;
 		break;
 	case IPPROTO_UDP:
@@ -320,24 +340,20 @@
 	if (!flow)
 		goto err_flow_alloc;
 
-	if (flow_offload_route_init(flow, &route) < 0)
-		goto err_flow_add;
-
-	if (tcph) {
-		ct->proto.tcp.seen[0].flags |= IP_CT_TCP_FLAG_BE_LIBERAL;
-		ct->proto.tcp.seen[1].flags |= IP_CT_TCP_FLAG_BE_LIBERAL;
-	}
+	flow_offload_route_init(flow, &route);
+	if (tcph)
+		flow_offload_ct_tcp(ct);
 
 	ret = flow_offload_add(flowtable, flow);
 	if (ret < 0)
 		goto err_flow_add;
 
-	dst_release(route.tuple[!dir].dst);
 	return;
 
 err_flow_add:
 	flow_offload_free(flow);
 err_flow_alloc:
+	dst_release(route.tuple[dir].dst);
 	dst_release(route.tuple[!dir].dst);
 err_flow_route:
 	clear_bit(IPS_OFFLOAD_BIT, &ct->status);
@@ -351,6 +367,11 @@
 {
 	unsigned int hook_mask = (1 << NF_INET_FORWARD);
 
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
 	return nft_chain_validate_hooks(ctx->chain, hook_mask);
 }
 
@@ -375,8 +396,10 @@
 	if (IS_ERR(flowtable))
 		return PTR_ERR(flowtable);
 
+	if (!nft_use_inc(&flowtable->use))
+		return -EMFILE;
+
 	priv->flowtable = flowtable;
-	flowtable->use++;
 
 	return nf_ct_netns_get(ctx->net, ctx->family);
 }
@@ -395,7 +418,7 @@
 {
 	struct nft_flow_offload *priv = nft_expr_priv(expr);
 
-	priv->flowtable->use++;
+	nft_use_inc_restore(&priv->flowtable->use);
 }
 
 static void nft_flow_offload_destroy(const struct nft_ctx *ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_fwd_netdev.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_fwd_netdev.c
@@ -77,6 +77,11 @@
 	return nft_fwd_dup_netdev_offload(ctx, flow, FLOW_ACTION_REDIRECT, oif);
 }
 
+static bool nft_fwd_netdev_offload_action(const struct nft_expr *expr)
+{
+	return true;
+}
+
 struct nft_fwd_neigh {
 	u8			sreg_dev;
 	u8			sreg_addr;
@@ -219,6 +224,7 @@
 	.dump		= nft_fwd_netdev_dump,
 	.validate	= nft_fwd_validate,
 	.offload	= nft_fwd_netdev_offload,
+	.offload_action	= nft_fwd_netdev_offload_action,
 };
 
 static const struct nft_expr_ops *
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_immediate.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_immediate.c
@@ -29,20 +29,36 @@
 	[NFTA_IMMEDIATE_DATA]	= { .type = NLA_NESTED },
 };
 
+static enum nft_data_types nft_reg_to_type(const struct nlattr *nla)
+{
+	enum nft_data_types type;
+	u8 reg;
+
+	reg = ntohl(nla_get_be32(nla));
+	if (reg == NFT_REG_VERDICT)
+		type = NFT_DATA_VERDICT;
+	else
+		type = NFT_DATA_VALUE;
+
+	return type;
+}
+
 static int nft_immediate_init(const struct nft_ctx *ctx,
 			      const struct nft_expr *expr,
 			      const struct nlattr * const tb[])
 {
 	struct nft_immediate_expr *priv = nft_expr_priv(expr);
-	struct nft_data_desc desc;
+	struct nft_data_desc desc = {
+		.size	= sizeof(priv->data),
+	};
 	int err;
 
 	if (tb[NFTA_IMMEDIATE_DREG] == NULL ||
 	    tb[NFTA_IMMEDIATE_DATA] == NULL)
 		return -EINVAL;
 
-	err = nft_data_init(ctx, &priv->data, sizeof(priv->data), &desc,
-			    tb[NFTA_IMMEDIATE_DATA]);
+	desc.type = nft_reg_to_type(tb[NFTA_IMMEDIATE_DREG]);
+	err = nft_data_init(ctx, &priv->data, &desc, tb[NFTA_IMMEDIATE_DATA]);
 	if (err < 0)
 		return err;
 
@@ -60,11 +76,9 @@
 		switch (priv->data.verdict.code) {
 		case NFT_JUMP:
 		case NFT_GOTO:
-			if (nft_chain_is_bound(chain)) {
-				err = -EBUSY;
+			err = nf_tables_bind_chain(ctx, chain);
+			if (err < 0)
 				goto err1;
-			}
-			chain->bound = true;
 			break;
 		default:
 			break;
@@ -82,15 +96,86 @@
 				   const struct nft_expr *expr)
 {
 	const struct nft_immediate_expr *priv = nft_expr_priv(expr);
+	const struct nft_data *data = &priv->data;
+	struct nft_ctx chain_ctx;
+	struct nft_chain *chain;
+	struct nft_rule *rule;
+
+	if (priv->dreg == NFT_REG_VERDICT) {
+		switch (data->verdict.code) {
+		case NFT_JUMP:
+		case NFT_GOTO:
+			chain = data->verdict.chain;
+			if (!nft_chain_binding(chain))
+				break;
+
+			chain_ctx = *ctx;
+			chain_ctx.chain = chain;
+
+			list_for_each_entry(rule, &chain->rules, list)
+				nft_rule_expr_activate(&chain_ctx, rule);
+
+			nft_clear(ctx->net, chain);
+			break;
+		default:
+			break;
+		}
+	}
 
 	return nft_data_hold(&priv->data, nft_dreg_to_type(priv->dreg));
 }
 
+static void nft_immediate_chain_deactivate(const struct nft_ctx *ctx,
+					   struct nft_chain *chain,
+					   enum nft_trans_phase phase)
+{
+	struct nft_ctx chain_ctx;
+	struct nft_rule *rule;
+
+	chain_ctx = *ctx;
+	chain_ctx.chain = chain;
+
+	list_for_each_entry(rule, &chain->rules, list)
+		nft_rule_expr_deactivate(&chain_ctx, rule, phase);
+}
+
 static void nft_immediate_deactivate(const struct nft_ctx *ctx,
 				     const struct nft_expr *expr,
 				     enum nft_trans_phase phase)
 {
 	const struct nft_immediate_expr *priv = nft_expr_priv(expr);
+	const struct nft_data *data = &priv->data;
+	struct nft_chain *chain;
+
+	if (priv->dreg == NFT_REG_VERDICT) {
+		switch (data->verdict.code) {
+		case NFT_JUMP:
+		case NFT_GOTO:
+			chain = data->verdict.chain;
+			if (!nft_chain_binding(chain))
+				break;
+
+			switch (phase) {
+			case NFT_TRANS_PREPARE_ERROR:
+				nf_tables_unbind_chain(ctx, chain);
+				nft_deactivate_next(ctx->net, chain);
+				break;
+			case NFT_TRANS_PREPARE:
+				nft_immediate_chain_deactivate(ctx, chain, phase);
+				nft_deactivate_next(ctx->net, chain);
+				break;
+			default:
+				nft_immediate_chain_deactivate(ctx, chain, phase);
+				nft_chain_del(chain);
+				chain->bound = false;
+				nft_use_dec(&chain->table->use);
+				break;
+			}
+			break;
+		default:
+			break;
+		}
+	}
 
 	if (phase == NFT_TRANS_COMMIT)
 		return;
@@ -115,15 +200,27 @@
 	case NFT_GOTO:
 		chain = data->verdict.chain;
 
-		if (!nft_chain_is_bound(chain))
+		if (!nft_chain_binding(chain))
 			break;
 
+		/* Rule construction failed, but chain is already bound:
+		 * let the transaction records release this chain and its rules.
+		 */
+		if (chain->bound) {
+			nft_use_dec(&chain->use);
+			break;
+		}
+
+		/* Rule has been deleted, release chain and its rules. */
 		chain_ctx = *ctx;
 		chain_ctx.chain = chain;
 
-		list_for_each_entry_safe(rule, n, &chain->rules, list)
-			nf_tables_rule_release(&chain_ctx, rule);
-
+		nft_use_dec(&chain->use);
+		list_for_each_entry_safe(rule, n, &chain->rules, list) {
+			nft_use_dec(&chain->use);
+			list_del(&rule->list);
+			nf_tables_rule_destroy(&chain_ctx, rule);
+		}
 		nf_tables_chain_destroy(&chain_ctx);
 		break;
 	default:
@@ -213,6 +310,16 @@
 	return 0;
 }
 
+static bool nft_immediate_offload_action(const struct nft_expr *expr)
+{
+	const struct nft_immediate_expr *priv = nft_expr_priv(expr);
+
+	if (priv->dreg == NFT_REG_VERDICT)
+		return true;
+
+	return false;
+}
+
 static const struct nft_expr_ops nft_imm_ops = {
 	.type		= &nft_imm_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_immediate_expr)),
@@ -224,7 +331,7 @@
 	.dump		= nft_immediate_dump,
 	.validate	= nft_immediate_validate,
 	.offload	= nft_immediate_offload,
-	.offload_flags	= NFT_OFFLOAD_F_ACTION,
+	.offload_action	= nft_immediate_offload_action,
 };
 
 struct nft_expr_type nft_imm_type __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_last.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_last.c
@@ -8,9 +8,13 @@
 #include <net/netfilter/nf_tables_core.h>
 #include <net/netfilter/nf_tables.h>
 
+struct nft_last {
+	unsigned long	jiffies;
+	unsigned int	set;
+};
+
 struct nft_last_priv {
-	unsigned long	last_jiffies;
-	unsigned int	last_set;
+	struct nft_last	*last;
 };
 
 static const struct nla_policy nft_last_policy[NFTA_LAST_MAX + 1] = {
@@ -22,47 +26,55 @@
 			 const struct nlattr * const tb[])
 {
 	struct nft_last_priv *priv = nft_expr_priv(expr);
+	struct nft_last *last;
 	u64 last_jiffies;
-	u32 last_set = 0;
 	int err;
 
-	if (tb[NFTA_LAST_SET]) {
-		last_set = ntohl(nla_get_be32(tb[NFTA_LAST_SET]));
-		if (last_set == 1)
-			priv->last_set = 1;
-	}
+	last = kzalloc(sizeof(*last), GFP_KERNEL_ACCOUNT);
+	if (!last)
+		return -ENOMEM;
 
-	if (last_set && tb[NFTA_LAST_MSECS]) {
+	if (tb[NFTA_LAST_SET])
+		last->set = ntohl(nla_get_be32(tb[NFTA_LAST_SET]));
+
+	if (last->set && tb[NFTA_LAST_MSECS]) {
 		err = nf_msecs_to_jiffies64(tb[NFTA_LAST_MSECS], &last_jiffies);
 		if (err < 0)
-			return err;
+			goto err;
 
-		priv->last_jiffies = jiffies - (unsigned long)last_jiffies;
+		last->jiffies = jiffies - (unsigned long)last_jiffies;
 	}
+	priv->last = last;
 
 	return 0;
+err:
+	kfree(last);
+
+	return err;
 }
 
 static void nft_last_eval(const struct nft_expr *expr,
 			  struct nft_regs *regs, const struct nft_pktinfo *pkt)
 {
 	struct nft_last_priv *priv = nft_expr_priv(expr);
+	struct nft_last *last = priv->last;
 
-	if (READ_ONCE(priv->last_jiffies) != jiffies)
-		WRITE_ONCE(priv->last_jiffies, jiffies);
-	if (READ_ONCE(priv->last_set) == 0)
-		WRITE_ONCE(priv->last_set, 1);
+	if (READ_ONCE(last->jiffies) != jiffies)
+		WRITE_ONCE(last->jiffies, jiffies);
+	if (READ_ONCE(last->set) == 0)
+		WRITE_ONCE(last->set, 1);
 }
 
 static int nft_last_dump(struct sk_buff *skb, const struct nft_expr *expr)
 {
 	struct nft_last_priv *priv = nft_expr_priv(expr);
-	unsigned long last_jiffies = READ_ONCE(priv->last_jiffies);
-	u32 last_set = READ_ONCE(priv->last_set);
+	struct nft_last *last = priv->last;
+	unsigned long last_jiffies = READ_ONCE(last->jiffies);
+	u32 last_set = READ_ONCE(last->set);
 	__be64 msecs;
 
 	if (time_before(jiffies, last_jiffies)) {
-		WRITE_ONCE(priv->last_set, 0);
+		WRITE_ONCE(last->set, 0);
 		last_set = 0;
 	}
 
@@ -81,11 +93,36 @@
 	return -1;
 }
 
+static void nft_last_destroy(const struct nft_ctx *ctx,
+			     const struct nft_expr *expr)
+{
+	struct nft_last_priv *priv = nft_expr_priv(expr);
+
+	kfree(priv->last);
+}
+
+static int nft_last_clone(struct nft_expr *dst, const struct nft_expr *src, gfp_t gfp)
+{
+	struct nft_last_priv *priv_dst = nft_expr_priv(dst);
+	struct nft_last_priv *priv_src = nft_expr_priv(src);
+
+	priv_dst->last = kzalloc(sizeof(*priv_dst->last), gfp);
+	if (!priv_dst->last)
+		return -ENOMEM;
+
+	priv_dst->last->set = priv_src->last->set;
+	priv_dst->last->jiffies = priv_src->last->jiffies;
+
+	return 0;
+}
+
 static const struct nft_expr_ops nft_last_ops = {
 	.type		= &nft_last_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_last_priv)),
 	.eval		= nft_last_eval,
 	.init		= nft_last_init,
+	.destroy	= nft_last_destroy,
+	.clone		= nft_last_clone,
 	.dump		= nft_last_dump,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_limit.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_limit.c
@@ -18,6 +18,10 @@
 	spinlock_t	lock;
 	u64		last;
 	u64		tokens;
+};
+
+struct nft_limit_priv {
+	struct nft_limit *limit;
 	u64		tokens_max;
 	u64		rate;
 	u64		nsecs;
@@ -25,93 +29,111 @@
 	bool		invert;
 };
 
-static inline bool nft_limit_eval(struct nft_limit *limit, u64 cost)
+static inline bool nft_limit_eval(struct nft_limit_priv *priv, u64 cost)
 {
 	u64 now, tokens;
 	s64 delta;
 
-	spin_lock_bh(&limit->lock);
+	spin_lock_bh(&priv->limit->lock);
 	now = ktime_get_ns();
-	tokens = limit->tokens + now - limit->last;
-	if (tokens > limit->tokens_max)
-		tokens = limit->tokens_max;
+	tokens = priv->limit->tokens + now - priv->limit->last;
+	if (tokens > priv->tokens_max)
+		tokens = priv->tokens_max;
 
-	limit->last = now;
+	priv->limit->last = now;
 	delta = tokens - cost;
 	if (delta >= 0) {
-		limit->tokens = delta;
-		spin_unlock_bh(&limit->lock);
-		return limit->invert;
+		priv->limit->tokens = delta;
+		spin_unlock_bh(&priv->limit->lock);
+		return priv->invert;
 	}
-	limit->tokens = tokens;
-	spin_unlock_bh(&limit->lock);
-	return !limit->invert;
+	priv->limit->tokens = tokens;
+	spin_unlock_bh(&priv->limit->lock);
+	return !priv->invert;
 }
 
 /* Use same default as in iptables. */
 #define NFT_LIMIT_PKT_BURST_DEFAULT	5
 
-static int nft_limit_init(struct nft_limit *limit,
+static int nft_limit_init(struct nft_limit_priv *priv,
 			  const struct nlattr * const tb[], bool pkts)
 {
-	u64 unit, tokens;
+	u64 unit, tokens, rate_with_burst;
+	bool invert = false;
 
 	if (tb[NFTA_LIMIT_RATE] == NULL ||
 	    tb[NFTA_LIMIT_UNIT] == NULL)
 		return -EINVAL;
 
-	limit->rate = be64_to_cpu(nla_get_be64(tb[NFTA_LIMIT_RATE]));
+	priv->rate = be64_to_cpu(nla_get_be64(tb[NFTA_LIMIT_RATE]));
+	if (priv->rate == 0)
+		return -EINVAL;
+
 	unit = be64_to_cpu(nla_get_be64(tb[NFTA_LIMIT_UNIT]));
-	limit->nsecs = unit * NSEC_PER_SEC;
-	if (limit->rate == 0 || limit->nsecs < unit)
+	if (check_mul_overflow(unit, NSEC_PER_SEC, &priv->nsecs))
 		return -EOVERFLOW;
 
 	if (tb[NFTA_LIMIT_BURST])
-		limit->burst = ntohl(nla_get_be32(tb[NFTA_LIMIT_BURST]));
+		priv->burst = ntohl(nla_get_be32(tb[NFTA_LIMIT_BURST]));
 
-	if (pkts && limit->burst == 0)
-		limit->burst = NFT_LIMIT_PKT_BURST_DEFAULT;
+	if (pkts && priv->burst == 0)
+		priv->burst = NFT_LIMIT_PKT_BURST_DEFAULT;
 
-	if (limit->rate + limit->burst < limit->rate)
+	if (check_add_overflow(priv->rate, priv->burst, &rate_with_burst))
 		return -EOVERFLOW;
 
 	if (pkts) {
-		tokens = div64_u64(limit->nsecs, limit->rate) * limit->burst;
+		u64 tmp = div64_u64(priv->nsecs, priv->rate);
+
+		if (check_mul_overflow(tmp, priv->burst, &tokens))
+			return -EOVERFLOW;
 	} else {
+		u64 tmp;
+
 		/* The token bucket size limits the number of tokens can be
 		 * accumulated. tokens_max specifies the bucket size.
 		 * tokens_max = unit * (rate + burst) / rate.
 		 */
-		tokens = div64_u64(limit->nsecs * (limit->rate + limit->burst),
-				 limit->rate);
-	}
+		if (check_mul_overflow(priv->nsecs, rate_with_burst, &tmp))
+			return -EOVERFLOW;
 
-	limit->tokens = tokens;
-	limit->tokens_max = limit->tokens;
+		tokens = div64_u64(tmp, priv->rate);
+	}
 
 	if (tb[NFTA_LIMIT_FLAGS]) {
 		u32 flags = ntohl(nla_get_be32(tb[NFTA_LIMIT_FLAGS]));
 
+		if (flags & ~NFT_LIMIT_F_INV)
+			return -EOPNOTSUPP;
+
 		if (flags & NFT_LIMIT_F_INV)
-			limit->invert = true;
+			invert = true;
 	}
-	limit->last = ktime_get_ns();
-	spin_lock_init(&limit->lock);
+
+	priv->limit = kmalloc(sizeof(*priv->limit), GFP_KERNEL_ACCOUNT);
+	if (!priv->limit)
+		return -ENOMEM;
+
+	priv->limit->tokens = tokens;
+	priv->tokens_max = priv->limit->tokens;
+	priv->invert = invert;
+	priv->limit->last = ktime_get_ns();
+	spin_lock_init(&priv->limit->lock);
 
 	return 0;
 }
 
-static int nft_limit_dump(struct sk_buff *skb, const struct nft_limit *limit,
+static int nft_limit_dump(struct sk_buff *skb, const struct nft_limit_priv *priv,
 			  enum nft_limit_type type)
 {
-	u32 flags = limit->invert ? NFT_LIMIT_F_INV : 0;
-	u64 secs = div_u64(limit->nsecs, NSEC_PER_SEC);
+	u32 flags = priv->invert ? NFT_LIMIT_F_INV : 0;
+	u64 secs = div_u64(priv->nsecs, NSEC_PER_SEC);
 
-	if (nla_put_be64(skb, NFTA_LIMIT_RATE, cpu_to_be64(limit->rate),
+	if (nla_put_be64(skb, NFTA_LIMIT_RATE, cpu_to_be64(priv->rate),
 			 NFTA_LIMIT_PAD) ||
 	    nla_put_be64(skb, NFTA_LIMIT_UNIT, cpu_to_be64(secs),
 			 NFTA_LIMIT_PAD) ||
-	    nla_put_be32(skb, NFTA_LIMIT_BURST, htonl(limit->burst)) ||
+	    nla_put_be32(skb, NFTA_LIMIT_BURST, htonl(priv->burst)) ||
 	    nla_put_be32(skb, NFTA_LIMIT_TYPE, htonl(type)) ||
 	    nla_put_be32(skb, NFTA_LIMIT_FLAGS, htonl(flags)))
 		goto nla_put_failure;
@@ -121,8 +143,34 @@
 	return -1;
 }
 
-struct nft_limit_pkts {
-	struct nft_limit	limit;
+static void nft_limit_destroy(const struct nft_ctx *ctx,
+			      const struct nft_limit_priv *priv)
+{
+	kfree(priv->limit);
+}
+
+static int nft_limit_clone(struct nft_limit_priv *priv_dst,
+			   const struct nft_limit_priv *priv_src, gfp_t gfp)
+{
+	priv_dst->tokens_max = priv_src->tokens_max;
+	priv_dst->rate = priv_src->rate;
+	priv_dst->nsecs = priv_src->nsecs;
+	priv_dst->burst = priv_src->burst;
+	priv_dst->invert = priv_src->invert;
+
+	priv_dst->limit = kmalloc(sizeof(*priv_dst->limit), gfp);
+	if (!priv_dst->limit)
+		return -ENOMEM;
+
+	spin_lock_init(&priv_dst->limit->lock);
+	priv_dst->limit->tokens = priv_src->tokens_max;
+	priv_dst->limit->last = ktime_get_ns();
+
+	return 0;
+}
+
+struct nft_limit_priv_pkts {
+	struct nft_limit_priv	limit;
 	u64			cost;
 };
 
@@ -130,7 +178,7 @@
 				struct nft_regs *regs,
 				const struct nft_pktinfo *pkt)
 {
-	struct nft_limit_pkts *priv = nft_expr_priv(expr);
+	struct nft_limit_priv_pkts *priv = nft_expr_priv(expr);
 
 	if (nft_limit_eval(&priv->limit, priv->cost))
 		regs->verdict.code = NFT_BREAK;
@@ -148,7 +196,7 @@
 			       const struct nft_expr *expr,
 			       const struct nlattr * const tb[])
 {
-	struct nft_limit_pkts *priv = nft_expr_priv(expr);
+	struct nft_limit_priv_pkts *priv = nft_expr_priv(expr);
 	int err;
 
 	err = nft_limit_init(&priv->limit, tb, true);
@@ -161,17 +209,38 @@
 
 static int nft_limit_pkts_dump(struct sk_buff *skb, const struct nft_expr *expr)
 {
-	const struct nft_limit_pkts *priv = nft_expr_priv(expr);
+	const struct nft_limit_priv_pkts *priv = nft_expr_priv(expr);
 
 	return nft_limit_dump(skb, &priv->limit, NFT_LIMIT_PKTS);
 }
 
+static void nft_limit_pkts_destroy(const struct nft_ctx *ctx,
+				   const struct nft_expr *expr)
+{
+	const struct nft_limit_priv_pkts *priv = nft_expr_priv(expr);
+
+	nft_limit_destroy(ctx, &priv->limit);
+}
+
+static int nft_limit_pkts_clone(struct nft_expr *dst, const struct nft_expr *src,
+				gfp_t gfp)
+{
+	struct nft_limit_priv_pkts *priv_dst = nft_expr_priv(dst);
+	struct nft_limit_priv_pkts *priv_src = nft_expr_priv(src);
+
+	priv_dst->cost = priv_src->cost;
+
+	return nft_limit_clone(&priv_dst->limit, &priv_src->limit, gfp);
+}
+
 static struct nft_expr_type nft_limit_type;
 static const struct nft_expr_ops nft_limit_pkts_ops = {
 	.type		= &nft_limit_type,
-	.size		= NFT_EXPR_SIZE(sizeof(struct nft_limit_pkts)),
+	.size		= NFT_EXPR_SIZE(sizeof(struct nft_limit_priv_pkts)),
 	.eval		= nft_limit_pkts_eval,
 	.init		= nft_limit_pkts_init,
+	.destroy	= nft_limit_pkts_destroy,
+	.clone		= nft_limit_pkts_clone,
 	.dump		= nft_limit_pkts_dump,
 };
 
@@ -179,7 +248,7 @@
 				 struct nft_regs *regs,
 				 const struct nft_pktinfo *pkt)
 {
-	struct nft_limit *priv = nft_expr_priv(expr);
+	struct nft_limit_priv *priv = nft_expr_priv(expr);
 	u64 cost = div64_u64(priv->nsecs * pkt->skb->len, priv->rate);
 
 	if (nft_limit_eval(priv, cost))
@@ -190,7 +259,7 @@
 				const struct nft_expr *expr,
 				const struct nlattr * const tb[])
 {
-	struct nft_limit *priv = nft_expr_priv(expr);
+	struct nft_limit_priv *priv = nft_expr_priv(expr);
 
 	return nft_limit_init(priv, tb, false);
 }
@@ -198,17 +267,36 @@
 static int nft_limit_bytes_dump(struct sk_buff *skb,
 				const struct nft_expr *expr)
 {
-	const struct nft_limit *priv = nft_expr_priv(expr);
+	const struct nft_limit_priv *priv = nft_expr_priv(expr);
 
 	return nft_limit_dump(skb, priv, NFT_LIMIT_PKT_BYTES);
 }
 
+static void nft_limit_bytes_destroy(const struct nft_ctx *ctx,
+				    const struct nft_expr *expr)
+{
+	const struct nft_limit_priv *priv = nft_expr_priv(expr);
+
+	nft_limit_destroy(ctx, priv);
+}
+
+static int nft_limit_bytes_clone(struct nft_expr *dst, const struct nft_expr *src,
+				 gfp_t gfp)
+{
+	struct nft_limit_priv *priv_dst = nft_expr_priv(dst);
+	struct nft_limit_priv *priv_src = nft_expr_priv(src);
+
+	return nft_limit_clone(priv_dst, priv_src, gfp);
+}
+
 static const struct nft_expr_ops nft_limit_bytes_ops = {
 	.type		= &nft_limit_type,
-	.size		= NFT_EXPR_SIZE(sizeof(struct nft_limit)),
+	.size		= NFT_EXPR_SIZE(sizeof(struct nft_limit_priv)),
 	.eval		= nft_limit_bytes_eval,
 	.init		= nft_limit_bytes_init,
 	.dump		= nft_limit_bytes_dump,
+	.clone		= nft_limit_bytes_clone,
+	.destroy	= nft_limit_bytes_destroy,
 };
 
 static const struct nft_expr_ops *
@@ -240,7 +328,7 @@
 				    struct nft_regs *regs,
 				    const struct nft_pktinfo *pkt)
 {
-	struct nft_limit_pkts *priv = nft_obj_data(obj);
+	struct nft_limit_priv_pkts *priv = nft_obj_data(obj);
 
 	if (nft_limit_eval(&priv->limit, priv->cost))
 		regs->verdict.code = NFT_BREAK;
@@ -250,7 +338,7 @@
 				   const struct nlattr * const tb[],
 				   struct nft_object *obj)
 {
-	struct nft_limit_pkts *priv = nft_obj_data(obj);
+	struct nft_limit_priv_pkts *priv = nft_obj_data(obj);
 	int err;
 
 	err = nft_limit_init(&priv->limit, tb, true);
@@ -265,16 +353,25 @@
 				   struct nft_object *obj,
 				   bool reset)
 {
-	const struct nft_limit_pkts *priv = nft_obj_data(obj);
+	const struct nft_limit_priv_pkts *priv = nft_obj_data(obj);
 
 	return nft_limit_dump(skb, &priv->limit, NFT_LIMIT_PKTS);
 }
 
+static void nft_limit_obj_pkts_destroy(const struct nft_ctx *ctx,
+				       struct nft_object *obj)
+{
+	struct nft_limit_priv_pkts *priv = nft_obj_data(obj);
+
+	nft_limit_destroy(ctx, &priv->limit);
+}
+
 static struct nft_object_type nft_limit_obj_type;
 static const struct nft_object_ops nft_limit_obj_pkts_ops = {
 	.type		= &nft_limit_obj_type,
-	.size		= NFT_EXPR_SIZE(sizeof(struct nft_limit_pkts)),
+	.size		= NFT_EXPR_SIZE(sizeof(struct nft_limit_priv_pkts)),
 	.init		= nft_limit_obj_pkts_init,
+	.destroy	= nft_limit_obj_pkts_destroy,
 	.eval		= nft_limit_obj_pkts_eval,
 	.dump		= nft_limit_obj_pkts_dump,
 };
@@ -283,7 +380,7 @@
 				     struct nft_regs *regs,
 				     const struct nft_pktinfo *pkt)
 {
-	struct nft_limit *priv = nft_obj_data(obj);
+	struct nft_limit_priv *priv = nft_obj_data(obj);
 	u64 cost = div64_u64(priv->nsecs * pkt->skb->len, priv->rate);
 
 	if (nft_limit_eval(priv, cost))
@@ -294,7 +391,7 @@
 				    const struct nlattr * const tb[],
 				    struct nft_object *obj)
 {
-	struct nft_limit *priv = nft_obj_data(obj);
+	struct nft_limit_priv *priv = nft_obj_data(obj);
 
 	return nft_limit_init(priv, tb, false);
 }
@@ -303,16 +400,25 @@
 				    struct nft_object *obj,
 				    bool reset)
 {
-	const struct nft_limit *priv = nft_obj_data(obj);
+	const struct nft_limit_priv *priv = nft_obj_data(obj);
 
 	return nft_limit_dump(skb, priv, NFT_LIMIT_PKT_BYTES);
 }
 
+static void nft_limit_obj_bytes_destroy(const struct nft_ctx *ctx,
+					struct nft_object *obj)
+{
+	struct nft_limit_priv *priv = nft_obj_data(obj);
+
+	nft_limit_destroy(ctx, priv);
+}
+
 static struct nft_object_type nft_limit_obj_type;
 static const struct nft_object_ops nft_limit_obj_bytes_ops = {
 	.type		= &nft_limit_obj_type,
-	.size		= sizeof(struct nft_limit),
+	.size		= sizeof(struct nft_limit_priv),
 	.init		= nft_limit_obj_bytes_init,
+	.destroy	= nft_limit_obj_bytes_destroy,
 	.eval		= nft_limit_obj_bytes_eval,
 	.dump		= nft_limit_obj_bytes_dump,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_lookup.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_lookup.c
@@ -136,7 +136,8 @@
 			return -EINVAL;
 
 		err = nft_parse_register_store(ctx, tb[NFTA_LOOKUP_DREG],
-					       &priv->dreg, NULL, set->dtype,
+					       &priv->dreg, NULL,
+					       nft_set_datatype(set),
 					       set->dlen);
 		if (err < 0)
 			return err;
@@ -167,7 +168,7 @@
 {
 	struct nft_lookup *priv = nft_expr_priv(expr);
 
-	priv->set->use++;
+	nf_tables_activate_set(ctx, priv->set);
 }
 
 static void nft_lookup_destroy(const struct nft_ctx *ctx,
@@ -198,37 +199,6 @@
 	return -1;
 }
 
-static int nft_lookup_validate_setelem(const struct nft_ctx *ctx,
-				       struct nft_set *set,
-				       const struct nft_set_iter *iter,
-				       struct nft_set_elem *elem)
-{
-	const struct nft_set_ext *ext = nft_set_elem_ext(set, elem->priv);
-	struct nft_ctx *pctx = (struct nft_ctx *)ctx;
-	const struct nft_data *data;
-	int err;
-
-	if (nft_set_ext_exists(ext, NFT_SET_EXT_FLAGS) &&
-	    *nft_set_ext_flags(ext) & NFT_SET_ELEM_INTERVAL_END)
-		return 0;
-
-	data = nft_set_ext_data(ext);
-	switch (data->verdict.code) {
-	case NFT_JUMP:
-	case NFT_GOTO:
-		pctx->level++;
-		err = nft_chain_validate(ctx, data->verdict.chain);
-		if (err < 0)
-			return err;
-		pctx->level--;
-		break;
-	default:
-		break;
-	}
-
-	return 0;
-}
-
 static int nft_lookup_validate(const struct nft_ctx *ctx,
 			       const struct nft_expr *expr,
 			       const struct nft_data **d)
@@ -241,12 +211,16 @@
 		return 0;
 
 	iter.genmask	= nft_genmask_next(ctx->net);
+	iter.type	= NFT_ITER_UPDATE;
 	iter.skip	= 0;
 	iter.count	= 0;
 	iter.err	= 0;
-	iter.fn		= nft_lookup_validate_setelem;
+	iter.fn		= nft_setelem_validate;
 
 	priv->set->ops->walk(ctx, priv->set, &iter);
+	if (!iter.err)
+		iter.err = nft_set_catchall_validate(ctx, priv->set);
+
 	if (iter.err < 0)
 		return iter.err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_masq.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_masq.c
@@ -43,7 +43,7 @@
 			 const struct nft_expr *expr,
 			 const struct nlattr * const tb[])
 {
-	u32 plen = sizeof_field(struct nf_nat_range, min_addr.all);
+	u32 plen = sizeof_field(struct nf_nat_range, min_proto.all);
 	struct nft_masq *priv = nft_expr_priv(expr);
 	int err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_meta.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_meta.c
@@ -14,6 +14,7 @@
 #include <linux/in.h>
 #include <linux/ip.h>
 #include <linux/ipv6.h>
+#include <linux/random.h>
 #include <linux/smp.h>
 #include <linux/static_key.h>
 #include <net/dst.h>
@@ -32,8 +33,6 @@
 #define NFT_META_SECS_PER_DAY		86400
 #define NFT_META_DAYS_PER_WEEK		7
 
-static DEFINE_PER_CPU(struct rnd_state, nft_prandom_state);
-
 static u8 nft_meta_weekday(void)
 {
 	time64_t secs = ktime_get_real_seconds();
@@ -64,7 +63,7 @@
 {
 	switch (key) {
 	case NFT_META_TIME_NS:
-		nft_reg_store64(dest, ktime_get_real_ns());
+		nft_reg_store64((u64 *)dest, ktime_get_real_ns());
 		break;
 	case NFT_META_TIME_DAY:
 		nft_reg_store8(dest, nft_meta_weekday());
@@ -267,13 +266,6 @@
 	return true;
 }
 
-static noinline u32 nft_prandom_u32(void)
-{
-	struct rnd_state *state = this_cpu_ptr(&nft_prandom_state);
-
-	return prandom_u32_state(state);
-}
-
 #ifdef CONFIG_IP_ROUTE_CLASSID
 static noinline bool
 nft_meta_get_eval_rtclassid(const struct sk_buff *skb, u32 *dest)
@@ -329,7 +321,7 @@
 		nft_reg_store8(dest, nft_pf(pkt));
 		break;
 	case NFT_META_L4PROTO:
-		if (!pkt->tprot_set)
+		if (!(pkt->flags & NFT_PKTINFO_L4PROTO))
 			goto err;
 		nft_reg_store8(dest, pkt->tprot);
 		break;
@@ -385,7 +377,7 @@
 		break;
 #endif
 	case NFT_META_PRANDOM:
-		*dest = nft_prandom_u32();
+		*dest = get_random_u32();
 		break;
 #ifdef CONFIG_XFRM
 	case NFT_META_SECPATH:
@@ -514,7 +506,6 @@
 		len = IFNAMSIZ;
 		break;
 	case NFT_META_PRANDOM:
-		prandom_init_once(&nft_prandom_state);
 		len = sizeof(u32);
 		break;
 #ifdef CONFIG_XFRM
@@ -799,7 +790,7 @@
 
 #ifdef CONFIG_NETWORK_SECMARK
 struct nft_secmark {
-	u32 secid;
+	struct lsmblob lsmdata;
 	char *ctx;
 };
 
@@ -809,21 +800,21 @@
 
 static int nft_secmark_compute_secid(struct nft_secmark *priv)
 {
-	u32 tmp_secid = 0;
+	struct lsmblob blob;
 	int err;
 
-	err = security_secctx_to_secid(priv->ctx, strlen(priv->ctx), &tmp_secid);
+	err = security_secctx_to_secid(priv->ctx, strlen(priv->ctx), &blob);
 	if (err)
 		return err;
 
-	if (!tmp_secid)
+	if (!lsmblob_is_set(&blob))
 		return -ENOENT;
 
-	err = security_secmark_relabel_packet(tmp_secid);
+	err = security_secmark_relabel_packet(&blob);
 	if (err)
 		return err;
 
-	priv->secid = tmp_secid;
+	priv->lsmdata = blob;
 	return 0;
 }
 
@@ -833,7 +824,11 @@
 	const struct nft_secmark *priv = nft_obj_data(obj);
 	struct sk_buff *skb = pkt->skb;
 
-	skb->secmark = priv->secid;
+	/* It is not possible for more than one secid to be set in
+	 * the lsmblob structure because it is set using
+	 * security_secctx_to_secid(). Any secid that is set must therefore
+	 * be the one that should go in the secmark. */
+	skb->secmark = lsmblob_value(&priv->lsmdata);
 }
 
 static int nft_secmark_obj_init(const struct nft_ctx *ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_nat.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_nat.c
@@ -142,6 +142,11 @@
 	struct nft_nat *priv = nft_expr_priv(expr);
 	int err;
 
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
 	err = nft_chain_validate_dependency(ctx->chain, NFT_CHAIN_T_NAT);
 	if (err < 0)
 		return err;
@@ -226,7 +231,7 @@
 		priv->flags |= NF_NAT_RANGE_MAP_IPS;
 	}
 
-	plen = sizeof_field(struct nf_nat_range, min_addr.all);
+	plen = sizeof_field(struct nf_nat_range, min_proto.all);
 	if (tb[NFTA_NAT_REG_PROTO_MIN]) {
 		err = nft_parse_register_load(tb[NFTA_NAT_REG_PROTO_MIN],
 					      &priv->sreg_proto_min, plen);
@@ -334,7 +339,8 @@
 {
 	const struct nft_nat *priv = nft_expr_priv(expr);
 
-	if (priv->family == nft_pf(pkt))
+	if (priv->family == nft_pf(pkt) ||
+	    priv->family == NFPROTO_INET)
 		nft_nat_eval(expr, regs, pkt);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_numgen.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_numgen.c
@@ -9,12 +9,11 @@
 #include <linux/netlink.h>
 #include <linux/netfilter.h>
 #include <linux/netfilter/nf_tables.h>
+#include <linux/random.h>
 #include <linux/static_key.h>
 #include <net/netfilter/nf_tables.h>
 #include <net/netfilter/nf_tables_core.h>
 
-static DEFINE_PER_CPU(struct rnd_state, nft_numgen_prandom_state);
-
 struct nft_ng_inc {
 	u8			dreg;
 	u32			modulus;
@@ -104,12 +103,9 @@
 	u32			offset;
 };
 
-static u32 nft_ng_random_gen(struct nft_ng_random *priv)
+static u32 nft_ng_random_gen(const struct nft_ng_random *priv)
 {
-	struct rnd_state *state = this_cpu_ptr(&nft_numgen_prandom_state);
-
-	return reciprocal_scale(prandom_u32_state(state), priv->modulus) +
-	       priv->offset;
+	return reciprocal_scale(get_random_u32(), priv->modulus) + priv->offset;
 }
 
 static void nft_ng_random_eval(const struct nft_expr *expr,
@@ -137,8 +133,6 @@
 	if (priv->offset + priv->modulus - 1 < priv->offset)
 		return -EOVERFLOW;
 
-	prandom_init_once(&nft_numgen_prandom_state);
-
 	return nft_parse_register_store(ctx, tb[NFTA_NG_DREG], &priv->dreg,
 					NULL, NFT_DATA_VALUE, sizeof(u32));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_objref.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_objref.c
@@ -41,8 +41,10 @@
 	if (IS_ERR(obj))
 		return -ENOENT;
 
+	if (!nft_use_inc(&obj->use))
+		return -EMFILE;
+
 	nft_objref_priv(expr) = obj;
-	obj->use++;
 
 	return 0;
 }
@@ -71,7 +73,7 @@
 	if (phase == NFT_TRANS_COMMIT)
 		return;
 
-	obj->use--;
+	nft_use_dec(&obj->use);
 }
 
 static void nft_objref_activate(const struct nft_ctx *ctx,
@@ -79,7 +81,7 @@
 {
 	struct nft_object *obj = nft_objref_priv(expr);
 
-	obj->use++;
+	nft_use_inc_restore(&obj->use);
 }
 
 static struct nft_expr_type nft_objref_type;
@@ -183,7 +185,7 @@
 {
 	struct nft_objref_map *priv = nft_expr_priv(expr);
 
-	priv->set->use++;
+	nf_tables_activate_set(ctx, priv->set);
 }
 
 static void nft_objref_map_destroy(const struct nft_ctx *ctx,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_osf.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_osf.c
@@ -99,7 +99,7 @@
 	if (nla_put_u8(skb, NFTA_OSF_TTL, priv->ttl))
 		goto nla_put_failure;
 
-	if (nla_put_be32(skb, NFTA_OSF_FLAGS, ntohl(priv->flags)))
+	if (nla_put_u32(skb, NFTA_OSF_FLAGS, ntohl((__force __be32)priv->flags)))
 		goto nla_put_failure;
 
 	if (nft_dump_register(skb, NFTA_OSF_DREG, priv->dreg))
@@ -115,9 +115,21 @@
 			    const struct nft_expr *expr,
 			    const struct nft_data **data)
 {
-	return nft_chain_validate_hooks(ctx->chain, (1 << NF_INET_LOCAL_IN) |
-						    (1 << NF_INET_PRE_ROUTING) |
-						    (1 << NF_INET_FORWARD));
+	unsigned int hooks;
+
+	switch (ctx->family) {
+	case NFPROTO_IPV4:
+	case NFPROTO_IPV6:
+	case NFPROTO_INET:
+		hooks = (1 << NF_INET_LOCAL_IN) |
+			(1 << NF_INET_PRE_ROUTING) |
+			(1 << NF_INET_FORWARD);
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	return nft_chain_validate_hooks(ctx->chain, hooks);
 }
 
 static struct nft_expr_type nft_osf_type;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_payload.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_payload.c
@@ -22,6 +22,7 @@
 #include <linux/icmpv6.h>
 #include <linux/ip.h>
 #include <linux/ipv6.h>
+#include <linux/ip.h>
 #include <net/sctp/checksum.h>
 
 static bool nft_payload_rebuild_vlan_hdr(const struct sk_buff *skb, int mac_off,
@@ -44,41 +45,82 @@
 	int mac_off = skb_mac_header(skb) - skb->data;
 	u8 *vlanh, *dst_u8 = (u8 *) d;
 	struct vlan_ethhdr veth;
-	u8 vlan_hlen = 0;
-
-	if ((skb->protocol == htons(ETH_P_8021AD) ||
-	     skb->protocol == htons(ETH_P_8021Q)) &&
-	    offset >= VLAN_ETH_HLEN && offset < VLAN_ETH_HLEN + VLAN_HLEN)
-		vlan_hlen += VLAN_HLEN;
 
 	vlanh = (u8 *) &veth;
-	if (offset < VLAN_ETH_HLEN + vlan_hlen) {
+	if (offset < VLAN_ETH_HLEN) {
 		u8 ethlen = len;
 
-		if (vlan_hlen &&
-		    skb_copy_bits(skb, mac_off, &veth, VLAN_ETH_HLEN) < 0)
-			return false;
-		else if (!nft_payload_rebuild_vlan_hdr(skb, mac_off, &veth))
+		if (!nft_payload_rebuild_vlan_hdr(skb, mac_off, &veth))
 			return false;
 
-		if (offset + len > VLAN_ETH_HLEN + vlan_hlen)
-			ethlen -= offset + len - VLAN_ETH_HLEN + vlan_hlen;
+		if (offset + len > VLAN_ETH_HLEN)
+			ethlen -= offset + len - VLAN_ETH_HLEN;
 
-		memcpy(dst_u8, vlanh + offset - vlan_hlen, ethlen);
+		memcpy(dst_u8, vlanh + offset, ethlen);
 
 		len -= ethlen;
 		if (len == 0)
 			return true;
 
 		dst_u8 += ethlen;
-		offset = ETH_HLEN + vlan_hlen;
+		offset = ETH_HLEN;
 	} else {
-		offset -= VLAN_HLEN + vlan_hlen;
+		offset -= VLAN_HLEN;
 	}
 
 	return skb_copy_bits(skb, offset + mac_off, dst_u8, len) == 0;
 }
 
+static int __nft_payload_inner_offset(struct nft_pktinfo *pkt)
+{
+	unsigned int thoff = nft_thoff(pkt);
+
+	if (!(pkt->flags & NFT_PKTINFO_L4PROTO) || pkt->fragoff)
+		return -1;
+
+	switch (pkt->tprot) {
+	case IPPROTO_UDP:
+		pkt->inneroff = thoff + sizeof(struct udphdr);
+		break;
+	case IPPROTO_TCP: {
+		struct tcphdr *th, _tcph;
+
+		th = skb_header_pointer(pkt->skb, thoff, sizeof(_tcph), &_tcph);
+		if (!th)
+			return -1;
+
+		pkt->inneroff = thoff + __tcp_hdrlen(th);
+		}
+		break;
+	default:
+		return -1;
+	}
+
+	pkt->flags |= NFT_PKTINFO_INNER;
+
+	return 0;
+}
+
+static int nft_payload_inner_offset(const struct nft_pktinfo *pkt)
+{
+	if (!(pkt->flags & NFT_PKTINFO_INNER) &&
+	    __nft_payload_inner_offset((struct nft_pktinfo *)pkt) < 0)
+		return -1;
+
+	return pkt->inneroff;
+}
+
+static bool nft_payload_need_vlan_adjust(u32 offset, u32 len)
+{
+	unsigned int boundary = offset + len;
+
+	/* data past ether src/dst requested, copy needed */
+	if (boundary > offsetof(struct ethhdr, h_proto))
+		return true;
+
+	return false;
+}
+
 void nft_payload_eval(const struct nft_expr *expr,
 		      struct nft_regs *regs,
 		      const struct nft_pktinfo *pkt)
@@ -93,10 +135,11 @@
 
 	switch (priv->base) {
 	case NFT_PAYLOAD_LL_HEADER:
-		if (!skb_mac_header_was_set(skb))
+		if (!skb_mac_header_was_set(skb) || skb_mac_header_len(skb) == 0)
 			goto err;
 
-		if (skb_vlan_tag_present(skb)) {
+		if (skb_vlan_tag_present(skb) &&
+		    nft_payload_need_vlan_adjust(priv->offset, priv->len)) {
 			if (!nft_payload_copy_vlan(dest, skb,
 						   priv->offset, priv->len))
 				goto err;
@@ -108,10 +151,15 @@
 		offset = skb_network_offset(skb);
 		break;
 	case NFT_PAYLOAD_TRANSPORT_HEADER:
-		if (!pkt->tprot_set)
+		if (!(pkt->flags & NFT_PKTINFO_L4PROTO) || pkt->fragoff)
 			goto err;
 		offset = nft_thoff(pkt);
 		break;
+	case NFT_PAYLOAD_INNER_HEADER:
+		offset = nft_payload_inner_offset(pkt);
+		if (offset < 0)
+			goto err;
+		break;
 	default:
 		BUG();
 	}
@@ -502,6 +550,9 @@
 				     struct sk_buff *skb,
 				     unsigned int *l4csum_offset)
 {
+	if (pkt->fragoff)
+		return -1;
+
 	switch (pkt->tprot) {
 	case IPPROTO_TCP:
 		*l4csum_offset = offsetof(struct tcphdr, check);
@@ -590,30 +641,103 @@
 	return 0;
 }
 
+struct nft_payload_set {
+	enum nft_payload_bases	base:8;
+	u8			offset;
+	u8			len;
+	u8			sreg;
+	u8			csum_type;
+	u8			csum_offset;
+	u8			csum_flags;
+};
+
+/* This is not struct vlan_hdr. */
+struct nft_payload_vlan_hdr {
+	__be16			h_vlan_proto;
+	__be16			h_vlan_TCI;
+};
+
+static bool
+nft_payload_set_vlan(const u32 *src, struct sk_buff *skb, u8 offset, u8 len,
+		     int *vlan_hlen)
+{
+	struct nft_payload_vlan_hdr *vlanh;
+	__be16 vlan_proto;
+	u16 vlan_tci;
+
+	if (offset >= offsetof(struct vlan_ethhdr, h_vlan_encapsulated_proto)) {
+		*vlan_hlen = VLAN_HLEN;
+		return true;
+	}
+
+	switch (offset) {
+	case offsetof(struct vlan_ethhdr, h_vlan_proto):
+		if (len == 2) {
+			vlan_proto = nft_reg_load_be16(src);
+			skb->vlan_proto = vlan_proto;
+		} else if (len == 4) {
+			vlanh = (struct nft_payload_vlan_hdr *)src;
+			__vlan_hwaccel_put_tag(skb, vlanh->h_vlan_proto,
+					       ntohs(vlanh->h_vlan_TCI));
+		} else {
+			return false;
+		}
+		break;
+	case offsetof(struct vlan_ethhdr, h_vlan_TCI):
+		if (len != 2)
+			return false;
+
+		vlan_tci = ntohs(nft_reg_load_be16(src));
+		skb->vlan_tci = vlan_tci;
+		break;
+	default:
+		return false;
+	}
+
+	return true;
+}
+
 static void nft_payload_set_eval(const struct nft_expr *expr,
 				 struct nft_regs *regs,
 				 const struct nft_pktinfo *pkt)
 {
 	const struct nft_payload_set *priv = nft_expr_priv(expr);
-	struct sk_buff *skb = pkt->skb;
 	const u32 *src = &regs->data[priv->sreg];
-	int offset, csum_offset;
+	int offset, csum_offset, vlan_hlen = 0;
+	struct sk_buff *skb = pkt->skb;
 	__wsum fsum, tsum;
 
 	switch (priv->base) {
 	case NFT_PAYLOAD_LL_HEADER:
 		if (!skb_mac_header_was_set(skb))
 			goto err;
-		offset = skb_mac_header(skb) - skb->data;
+
+		if (skb_vlan_tag_present(skb) &&
+		    nft_payload_need_vlan_adjust(priv->offset, priv->len)) {
+			if (!nft_payload_set_vlan(src, skb,
+						  priv->offset, priv->len,
+						  &vlan_hlen))
+				goto err;
+
+			if (!vlan_hlen)
+				return;
+		}
+
+		offset = skb_mac_header(skb) - skb->data - vlan_hlen;
 		break;
 	case NFT_PAYLOAD_NETWORK_HEADER:
 		offset = skb_network_offset(skb);
 		break;
 	case NFT_PAYLOAD_TRANSPORT_HEADER:
-		if (!pkt->tprot_set)
+		if (!(pkt->flags & NFT_PKTINFO_L4PROTO) || pkt->fragoff)
 			goto err;
 		offset = nft_thoff(pkt);
 		break;
+	case NFT_PAYLOAD_INNER_HEADER:
+		offset = nft_payload_inner_offset(pkt);
+		if (offset < 0)
+			goto err;
+		break;
 	default:
 		BUG();
 	}
@@ -622,8 +746,12 @@
 	offset += priv->offset;
 
 	if ((priv->csum_type == NFT_PAYLOAD_CSUM_INET || priv->csum_flags) &&
-	    (priv->base != NFT_PAYLOAD_TRANSPORT_HEADER ||
+	    ((priv->base != NFT_PAYLOAD_TRANSPORT_HEADER &&
+	      priv->base != NFT_PAYLOAD_INNER_HEADER) ||
 	     skb->ip_summed != CHECKSUM_PARTIAL)) {
+		if (offset + priv->len > skb->len)
+			goto err;
+
 		fsum = skb_checksum(skb, offset, priv->len, 0);
 		tsum = csum_partial(src, priv->len, 0);
 
@@ -643,7 +771,8 @@
 	if (priv->csum_type == NFT_PAYLOAD_CSUM_SCTP &&
 	    pkt->tprot == IPPROTO_SCTP &&
 	    skb->ip_summed != CHECKSUM_PARTIAL) {
-		if (nft_payload_csum_sctp(skb, nft_thoff(pkt)))
+		if (pkt->fragoff == 0 &&
+		    nft_payload_csum_sctp(skb, nft_thoff(pkt)))
 			goto err;
 	}
 
@@ -657,17 +786,23 @@
 				const struct nlattr * const tb[])
 {
 	struct nft_payload_set *priv = nft_expr_priv(expr);
+	u32 csum_offset, csum_type = NFT_PAYLOAD_CSUM_NONE;
+	int err;
 
 	priv->base        = ntohl(nla_get_be32(tb[NFTA_PAYLOAD_BASE]));
 	priv->offset      = ntohl(nla_get_be32(tb[NFTA_PAYLOAD_OFFSET]));
 	priv->len         = ntohl(nla_get_be32(tb[NFTA_PAYLOAD_LEN]));
 
 	if (tb[NFTA_PAYLOAD_CSUM_TYPE])
-		priv->csum_type =
-			ntohl(nla_get_be32(tb[NFTA_PAYLOAD_CSUM_TYPE]));
-	if (tb[NFTA_PAYLOAD_CSUM_OFFSET])
-		priv->csum_offset =
-			ntohl(nla_get_be32(tb[NFTA_PAYLOAD_CSUM_OFFSET]));
+		csum_type = ntohl(nla_get_be32(tb[NFTA_PAYLOAD_CSUM_TYPE]));
+	if (tb[NFTA_PAYLOAD_CSUM_OFFSET]) {
+		err = nft_parse_u32_check(tb[NFTA_PAYLOAD_CSUM_OFFSET], U8_MAX,
+					  &csum_offset);
+		if (err < 0)
+			return err;
+
+		priv->csum_offset = csum_offset;
+	}
 	if (tb[NFTA_PAYLOAD_CSUM_FLAGS]) {
 		u32 flags;
 
@@ -678,7 +813,7 @@
 		priv->csum_flags = flags;
 	}
 
-	switch (priv->csum_type) {
+	switch (csum_type) {
 	case NFT_PAYLOAD_CSUM_NONE:
 	case NFT_PAYLOAD_CSUM_INET:
 		break;
@@ -692,6 +827,7 @@
 	default:
 		return -EOPNOTSUPP;
 	}
+	priv->csum_type = csum_type;
 
 	return nft_parse_register_load(tb[NFTA_PAYLOAD_SREG], &priv->sreg,
 				       priv->len);
@@ -730,6 +866,7 @@
 {
 	enum nft_payload_bases base;
 	unsigned int offset, len;
+	int err;
 
 	if (tb[NFTA_PAYLOAD_BASE] == NULL ||
 	    tb[NFTA_PAYLOAD_OFFSET] == NULL ||
@@ -741,6 +878,7 @@
 	case NFT_PAYLOAD_LL_HEADER:
 	case NFT_PAYLOAD_NETWORK_HEADER:
 	case NFT_PAYLOAD_TRANSPORT_HEADER:
+	case NFT_PAYLOAD_INNER_HEADER:
 		break;
 	default:
 		return ERR_PTR(-EOPNOTSUPP);
@@ -755,11 +893,16 @@
 	if (tb[NFTA_PAYLOAD_DREG] == NULL)
 		return ERR_PTR(-EINVAL);
 
-	offset = ntohl(nla_get_be32(tb[NFTA_PAYLOAD_OFFSET]));
-	len    = ntohl(nla_get_be32(tb[NFTA_PAYLOAD_LEN]));
+	err = nft_parse_u32_check(tb[NFTA_PAYLOAD_OFFSET], U8_MAX, &offset);
+	if (err < 0)
+		return ERR_PTR(err);
+
+	err = nft_parse_u32_check(tb[NFTA_PAYLOAD_LEN], U8_MAX, &len);
+	if (err < 0)
+		return ERR_PTR(err);
 
 	if (len <= 4 && is_power_of_2(len) && IS_ALIGNED(offset, len) &&
-	    base != NFT_PAYLOAD_LL_HEADER)
+	    base != NFT_PAYLOAD_LL_HEADER && base != NFT_PAYLOAD_INNER_HEADER)
 		return &nft_payload_fast_ops;
 	else
 		return &nft_payload_ops;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_quota.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_quota.c
@@ -15,13 +15,13 @@
 struct nft_quota {
 	atomic64_t	quota;
 	unsigned long	flags;
-	atomic64_t	consumed;
+	atomic64_t	*consumed;
 };
 
 static inline bool nft_overquota(struct nft_quota *priv,
 				 const struct sk_buff *skb)
 {
-	return atomic64_add_return(skb->len, &priv->consumed) >=
+	return atomic64_add_return(skb->len, priv->consumed) >=
 	       atomic64_read(&priv->quota);
 }
 
@@ -90,13 +90,23 @@
 			return -EOPNOTSUPP;
 	}
 
+	priv->consumed = kmalloc(sizeof(*priv->consumed), GFP_KERNEL_ACCOUNT);
+	if (!priv->consumed)
+		return -ENOMEM;
+
 	atomic64_set(&priv->quota, quota);
 	priv->flags = flags;
-	atomic64_set(&priv->consumed, consumed);
+	atomic64_set(priv->consumed, consumed);
 
 	return 0;
 }
 
+static void nft_quota_do_destroy(const struct nft_ctx *ctx,
+				 struct nft_quota *priv)
+{
+	kfree(priv->consumed);
+}
+
 static int nft_quota_obj_init(const struct nft_ctx *ctx,
 			      const struct nlattr * const tb[],
 			      struct nft_object *obj)
@@ -128,7 +138,7 @@
 	 * that we see, don't go over the quota boundary in what we send to
 	 * userspace.
 	 */
-	consumed = atomic64_read(&priv->consumed);
+	consumed = atomic64_read(priv->consumed);
 	quota = atomic64_read(&priv->quota);
 	if (consumed >= quota) {
 		consumed_cap = quota;
@@ -145,7 +155,7 @@
 		goto nla_put_failure;
 
 	if (reset) {
-		atomic64_sub(consumed, &priv->consumed);
+		atomic64_sub(consumed, priv->consumed);
 		clear_bit(NFT_QUOTA_DEPLETED_BIT, &priv->flags);
 	}
 	return 0;
@@ -162,11 +172,20 @@
 	return nft_quota_do_dump(skb, priv, reset);
 }
 
+static void nft_quota_obj_destroy(const struct nft_ctx *ctx,
+				  struct nft_object *obj)
+{
+	struct nft_quota *priv = nft_obj_data(obj);
+
+	return nft_quota_do_destroy(ctx, priv);
+}
+
 static struct nft_object_type nft_quota_obj_type;
 static const struct nft_object_ops nft_quota_obj_ops = {
 	.type		= &nft_quota_obj_type,
 	.size		= sizeof(struct nft_quota),
 	.init		= nft_quota_obj_init,
+	.destroy	= nft_quota_obj_destroy,
 	.eval		= nft_quota_obj_eval,
 	.dump		= nft_quota_obj_dump,
 	.update		= nft_quota_obj_update,
@@ -205,12 +224,39 @@
 	return nft_quota_do_dump(skb, priv, false);
 }
 
+static void nft_quota_destroy(const struct nft_ctx *ctx,
+			      const struct nft_expr *expr)
+{
+	struct nft_quota *priv = nft_expr_priv(expr);
+
+	return nft_quota_do_destroy(ctx, priv);
+}
+
+static int nft_quota_clone(struct nft_expr *dst, const struct nft_expr *src, gfp_t gfp)
+{
+	struct nft_quota *priv_dst = nft_expr_priv(dst);
+	struct nft_quota *priv_src = nft_expr_priv(src);
+
+	priv_dst->quota = priv_src->quota;
+	priv_dst->flags = priv_src->flags;
+
+	priv_dst->consumed = kmalloc(sizeof(*priv_dst->consumed), gfp);
+	if (!priv_dst->consumed)
+		return -ENOMEM;
+
+	*priv_dst->consumed = *priv_src->consumed;
+
+	return 0;
+}
+
 static struct nft_expr_type nft_quota_type;
 static const struct nft_expr_ops nft_quota_ops = {
 	.type		= &nft_quota_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_quota)),
 	.eval		= nft_quota_eval,
 	.init		= nft_quota_init,
+	.destroy	= nft_quota_destroy,
+	.clone		= nft_quota_clone,
 	.dump		= nft_quota_dump,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_range.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_range.c
@@ -51,7 +51,14 @@
 			const struct nlattr * const tb[])
 {
 	struct nft_range_expr *priv = nft_expr_priv(expr);
-	struct nft_data_desc desc_from, desc_to;
+	struct nft_data_desc desc_from = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->data_from),
+	};
+	struct nft_data_desc desc_to = {
+		.type	= NFT_DATA_VALUE,
+		.size	= sizeof(priv->data_to),
+	};
 	int err;
 	u32 op;
 
@@ -61,26 +68,16 @@
 	    !tb[NFTA_RANGE_TO_DATA])
 		return -EINVAL;
 
-	err = nft_data_init(NULL, &priv->data_from, sizeof(priv->data_from),
-			    &desc_from, tb[NFTA_RANGE_FROM_DATA]);
+	err = nft_data_init(NULL, &priv->data_from, &desc_from,
+			    tb[NFTA_RANGE_FROM_DATA]);
 	if (err < 0)
 		return err;
 
-	if (desc_from.type != NFT_DATA_VALUE) {
-		err = -EINVAL;
-		goto err1;
-	}
-
-	err = nft_data_init(NULL, &priv->data_to, sizeof(priv->data_to),
-			    &desc_to, tb[NFTA_RANGE_TO_DATA]);
+	err = nft_data_init(NULL, &priv->data_to, &desc_to,
+			    tb[NFTA_RANGE_TO_DATA]);
 	if (err < 0)
 		goto err1;
 
-	if (desc_to.type != NFT_DATA_VALUE) {
-		err = -EINVAL;
-		goto err2;
-	}
-
 	if (desc_from.len != desc_to.len) {
 		err = -EINVAL;
 		goto err2;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_redir.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_redir.c
@@ -48,7 +48,7 @@
 	unsigned int plen;
 	int err;
 
-	plen = sizeof_field(struct nf_nat_range, min_addr.all);
+	plen = sizeof_field(struct nf_nat_range, min_proto.all);
 	if (tb[NFTA_REDIR_REG_PROTO_MIN]) {
 		err = nft_parse_register_load(tb[NFTA_REDIR_REG_PROTO_MIN],
 					      &priv->sreg_proto_min, plen);
@@ -64,6 +64,8 @@
 		} else {
 			priv->sreg_proto_max = priv->sreg_proto_min;
 		}
+
+		priv->flags |= NF_NAT_RANGE_PROTO_SPECIFIED;
 	}
 
 	if (tb[NFTA_REDIR_FLAGS]) {
@@ -98,25 +100,37 @@
 	return -1;
 }
 
-static void nft_redir_ipv4_eval(const struct nft_expr *expr,
-				struct nft_regs *regs,
-				const struct nft_pktinfo *pkt)
+static void nft_redir_eval(const struct nft_expr *expr,
+			   struct nft_regs *regs,
+			   const struct nft_pktinfo *pkt)
 {
-	struct nft_redir *priv = nft_expr_priv(expr);
-	struct nf_nat_ipv4_multi_range_compat mr;
+	const struct nft_redir *priv = nft_expr_priv(expr);
+	struct nf_nat_range2 range;
 
-	memset(&mr, 0, sizeof(mr));
+	memset(&range, 0, sizeof(range));
+	range.flags = priv->flags;
 	if (priv->sreg_proto_min) {
-		mr.range[0].min.all = (__force __be16)nft_reg_load16(
-			&regs->data[priv->sreg_proto_min]);
-		mr.range[0].max.all = (__force __be16)nft_reg_load16(
-			&regs->data[priv->sreg_proto_max]);
-		mr.range[0].flags |= NF_NAT_RANGE_PROTO_SPECIFIED;
+		range.min_proto.all = (__force __be16)
+			nft_reg_load16(&regs->data[priv->sreg_proto_min]);
+		range.max_proto.all = (__force __be16)
+			nft_reg_load16(&regs->data[priv->sreg_proto_max]);
 	}
 
-	mr.range[0].flags |= priv->flags;
-
-	regs->verdict.code = nf_nat_redirect_ipv4(pkt->skb, &mr, nft_hook(pkt));
+	switch (nft_pf(pkt)) {
+	case NFPROTO_IPV4:
+		regs->verdict.code = nf_nat_redirect_ipv4(pkt->skb, &range,
+							  nft_hook(pkt));
+		break;
+#ifdef CONFIG_NF_TABLES_IPV6
+	case NFPROTO_IPV6:
+		regs->verdict.code = nf_nat_redirect_ipv6(pkt->skb, &range,
+							  nft_hook(pkt));
+		break;
+#endif
+	default:
+		WARN_ON_ONCE(1);
+		break;
+	}
 }
 
 static void
@@ -129,7 +143,7 @@
 static const struct nft_expr_ops nft_redir_ipv4_ops = {
 	.type		= &nft_redir_ipv4_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_redir)),
-	.eval		= nft_redir_ipv4_eval,
+	.eval		= nft_redir_eval,
 	.init		= nft_redir_init,
 	.destroy	= nft_redir_ipv4_destroy,
 	.dump		= nft_redir_dump,
@@ -146,28 +160,6 @@
 };
 
 #ifdef CONFIG_NF_TABLES_IPV6
-static void nft_redir_ipv6_eval(const struct nft_expr *expr,
-				struct nft_regs *regs,
-				const struct nft_pktinfo *pkt)
-{
-	struct nft_redir *priv = nft_expr_priv(expr);
-	struct nf_nat_range2 range;
-
-	memset(&range, 0, sizeof(range));
-	if (priv->sreg_proto_min) {
-		range.min_proto.all = (__force __be16)nft_reg_load16(
-			&regs->data[priv->sreg_proto_min]);
-		range.max_proto.all = (__force __be16)nft_reg_load16(
-			&regs->data[priv->sreg_proto_max]);
-		range.flags |= NF_NAT_RANGE_PROTO_SPECIFIED;
-	}
-
-	range.flags |= priv->flags;
-
-	regs->verdict.code =
-		nf_nat_redirect_ipv6(pkt->skb, &range, nft_hook(pkt));
-}
-
 static void
 nft_redir_ipv6_destroy(const struct nft_ctx *ctx, const struct nft_expr *expr)
 {
@@ -178,7 +170,7 @@
 static const struct nft_expr_ops nft_redir_ipv6_ops = {
 	.type		= &nft_redir_ipv6_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_redir)),
-	.eval		= nft_redir_ipv6_eval,
+	.eval		= nft_redir_eval,
 	.init		= nft_redir_init,
 	.destroy	= nft_redir_ipv6_destroy,
 	.dump		= nft_redir_dump,
@@ -196,20 +188,6 @@
 #endif
 
 #ifdef CONFIG_NF_TABLES_INET
-static void nft_redir_inet_eval(const struct nft_expr *expr,
-				struct nft_regs *regs,
-				const struct nft_pktinfo *pkt)
-{
-	switch (nft_pf(pkt)) {
-	case NFPROTO_IPV4:
-		return nft_redir_ipv4_eval(expr, regs, pkt);
-	case NFPROTO_IPV6:
-		return nft_redir_ipv6_eval(expr, regs, pkt);
-	}
-
-	WARN_ON_ONCE(1);
-}
-
 static void
 nft_redir_inet_destroy(const struct nft_ctx *ctx, const struct nft_expr *expr)
 {
@@ -220,7 +198,7 @@
 static const struct nft_expr_ops nft_redir_inet_ops = {
 	.type		= &nft_redir_inet_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_redir)),
-	.eval		= nft_redir_inet_eval,
+	.eval		= nft_redir_eval,
 	.init		= nft_redir_init,
 	.destroy	= nft_redir_inet_destroy,
 	.dump		= nft_redir_dump,
@@ -232,7 +210,7 @@
 	.name		= "redir",
 	.ops		= &nft_redir_inet_ops,
 	.policy		= nft_redir_policy,
-	.maxattr	= NFTA_MASQ_MAX,
+	.maxattr	= NFTA_REDIR_MAX,
 	.owner		= THIS_MODULE,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_rt.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_rt.c
@@ -166,6 +166,11 @@
 	const struct nft_rt *priv = nft_expr_priv(expr);
 	unsigned int hooks;
 
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
 	switch (priv->key) {
 	case NFT_RT_NEXTHOP4:
 	case NFT_RT_NEXTHOP6:
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_set_bitmap.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_set_bitmap.c
@@ -171,7 +171,7 @@
 	nft_bitmap_location(set, nft_set_ext_key(&be->ext), &idx, &off);
 	/* Enter 11 state. */
 	priv->bitmap[idx] |= (genmask << off);
-	nft_set_elem_change_active(net, set, &be->ext);
+	nft_clear(net, &be->ext);
 }
 
 static bool nft_bitmap_flush(const struct net *net,
@@ -223,8 +223,6 @@
 	list_for_each_entry_rcu(be, &priv->list, head) {
 		if (iter->count < iter->skip)
 			goto cont;
-		if (!nft_set_elem_active(&be->ext, iter->genmask))
-			goto cont;
 
 		elem.priv = be;
 
@@ -271,13 +269,14 @@
 	return 0;
 }
 
-static void nft_bitmap_destroy(const struct nft_set *set)
+static void nft_bitmap_destroy(const struct nft_ctx *ctx,
+			       const struct nft_set *set)
 {
 	struct nft_bitmap *priv = nft_set_priv(set);
 	struct nft_bitmap_elem *be, *n;
 
 	list_for_each_entry_safe(be, n, &priv->list, head)
-		nft_set_elem_destroy(set, be, true);
+		nf_tables_set_elem_destroy(ctx, set, be);
 }
 
 static bool nft_bitmap_estimate(const struct nft_set_desc *desc, u32 features,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_set_hash.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_set_hash.c
@@ -24,10 +24,12 @@
 struct nft_rhash {
 	struct rhashtable		ht;
 	struct delayed_work		gc_work;
+	u32				wq_gc_seq;
 };
 
 struct nft_rhash_elem {
 	struct rhash_head		node;
+	u32				wq_gc_seq;
 	struct nft_set_ext		ext;
 };
 
@@ -35,6 +37,7 @@
 	const struct nft_set		*set;
 	const u32			*key;
 	u8				genmask;
+	u64				tstamp;
 };
 
 static inline u32 nft_rhash_key(const void *data, u32 len, u32 seed)
@@ -59,7 +62,9 @@
 
 	if (memcmp(nft_set_ext_key(&he->ext), x->key, x->set->klen))
 		return 1;
-	if (nft_set_elem_expired(&he->ext))
+	if (nft_set_elem_is_dead(&he->ext))
+		return 1;
+	if (__nft_set_elem_expired(&he->ext, x->tstamp))
 		return 1;
 	if (!nft_set_elem_active(&he->ext, x->genmask))
 		return 1;
@@ -84,6 +89,7 @@
 		.genmask = nft_genmask_cur(net),
 		.set	 = set,
 		.key	 = key,
+		.tstamp  = get_jiffies_64(),
 	};
 
 	he = rhashtable_lookup(&priv->ht, &arg, nft_rhash_params);
@@ -102,6 +108,7 @@
 		.genmask = nft_genmask_cur(net),
 		.set	 = set,
 		.key	 = elem->key.val.data,
+		.tstamp  = get_jiffies_64(),
 	};
 
 	he = rhashtable_lookup(&priv->ht, &arg, nft_rhash_params);
@@ -125,6 +132,7 @@
 		.genmask = NFT_GENMASK_ANY,
 		.set	 = set,
 		.key	 = key,
+		.tstamp  = get_jiffies_64(),
 	};
 
 	he = rhashtable_lookup(&priv->ht, &arg, nft_rhash_params);
@@ -143,6 +151,7 @@
 	/* Another cpu may race to insert the element with the same key */
 	if (prev) {
 		nft_set_elem_destroy(set, he, true);
+		atomic_dec(&set->nelems);
 		he = prev;
 	}
 
@@ -152,6 +161,7 @@
 
 err2:
 	nft_set_elem_destroy(set, he, true);
+	atomic_dec(&set->nelems);
 err1:
 	return false;
 }
@@ -166,6 +176,7 @@
 		.genmask = nft_genmask_next(net),
 		.set	 = set,
 		.key	 = elem->key.val.data,
+		.tstamp	 = nft_net_tstamp(net),
 	};
 	struct nft_rhash_elem *prev;
 
@@ -185,8 +196,7 @@
 {
 	struct nft_rhash_elem *he = elem->priv;
 
-	nft_set_elem_change_active(net, set, &he->ext);
-	nft_set_elem_clear_busy(&he->ext);
+	nft_clear(net, &he->ext);
 }
 
 static bool nft_rhash_flush(const struct net *net,
@@ -194,12 +204,9 @@
 {
 	struct nft_rhash_elem *he = priv;
 
-	if (!nft_set_elem_mark_busy(&he->ext) ||
-	    !nft_is_active(net, &he->ext)) {
-		nft_set_elem_change_active(net, set, &he->ext);
-		return true;
-	}
-	return false;
+	nft_set_elem_change_active(net, set, &he->ext);
+
+	return true;
 }
 
 static void *nft_rhash_deactivate(const struct net *net,
@@ -212,13 +219,13 @@
 		.genmask = nft_genmask_next(net),
 		.set	 = set,
 		.key	 = elem->key.val.data,
+		.tstamp	 = nft_net_tstamp(net),
 	};
 
 	rcu_read_lock();
 	he = rhashtable_lookup(&priv->ht, &arg, nft_rhash_params);
-	if (he != NULL &&
-	    !nft_rhash_flush(net, set, he))
-		he = NULL;
+	if (he)
+		nft_set_elem_change_active(net, set, &he->ext);
 
 	rcu_read_unlock();
 
@@ -250,7 +257,9 @@
 	if (he == NULL)
 		return false;
 
-	return rhashtable_remove_fast(&priv->ht, &he->node, nft_rhash_params) == 0;
+	nft_set_elem_dead(&he->ext);
+
+	return true;
 }
 
 static void nft_rhash_walk(const struct nft_ctx *ctx, struct nft_set *set,
@@ -276,10 +285,6 @@
 
 		if (iter->count < iter->skip)
 			goto cont;
-		if (nft_set_elem_expired(&he->ext))
-			goto cont;
-		if (!nft_set_elem_active(&he->ext, iter->genmask))
-			goto cont;
 
 		elem.priv = he;
 
@@ -303,7 +308,8 @@
 
 	nft_setelem_expr_foreach(expr, elem_expr, size) {
 		if (expr->ops->gc &&
-		    expr->ops->gc(read_pnet(&set->net), expr))
+		    expr->ops->gc(read_pnet(&set->net), expr) &&
+		    set->flags & NFT_SET_EVAL)
 			return true;
 	}
 
@@ -312,25 +318,60 @@
 
 static void nft_rhash_gc(struct work_struct *work)
 {
+	struct nftables_pernet *nft_net;
 	struct nft_set *set;
 	struct nft_rhash_elem *he;
 	struct nft_rhash *priv;
-	struct nft_set_gc_batch *gcb = NULL;
 	struct rhashtable_iter hti;
+	struct nft_trans_gc *gc;
+	struct net *net;
+	u32 gc_seq;
 
 	priv = container_of(work, struct nft_rhash, gc_work.work);
 	set  = nft_set_container_of(priv);
+	net  = read_pnet(&set->net);
+	nft_net = nft_pernet(net);
+	gc_seq = READ_ONCE(nft_net->gc_seq);
+
+	if (nft_set_gc_is_pending(set))
+		goto done;
+
+	gc = nft_trans_gc_alloc(set, gc_seq, GFP_KERNEL);
+	if (!gc)
+		goto done;
+
+	/* Elements never collected use a zero gc worker sequence number. */
+	if (unlikely(++priv->wq_gc_seq == 0))
+		priv->wq_gc_seq++;
 
 	rhashtable_walk_enter(&priv->ht, &hti);
 	rhashtable_walk_start(&hti);
 
 	while ((he = rhashtable_walk_next(&hti))) {
 		if (IS_ERR(he)) {
-			if (PTR_ERR(he) != -EAGAIN)
-				break;
-			continue;
+			nft_trans_gc_destroy(gc);
+			gc = NULL;
+			goto try_later;
+		}
+
+		/* Ruleset has been updated, try later. */
+		if (READ_ONCE(nft_net->gc_seq) != gc_seq) {
+			nft_trans_gc_destroy(gc);
+			gc = NULL;
+			goto try_later;
 		}
 
+		/* rhashtable walk is unstable, already seen in this gc run?
+		 * Then, skip this element. In case of (unlikely) sequence
+		 * wraparound and stale element wq_gc_seq, next gc run will
+		 * just find this expired element.
+		 */
+		if (he->wq_gc_seq == priv->wq_gc_seq)
+			continue;
+
+		if (nft_set_elem_is_dead(&he->ext))
+			goto dead_elem;
+
 		if (nft_set_ext_exists(&he->ext, NFT_SET_EXT_EXPRESSIONS) &&
 		    nft_rhash_expr_needs_gc_run(set, &he->ext))
 			goto needs_gc_run;
@@ -338,26 +379,28 @@
 		if (!nft_set_elem_expired(&he->ext))
 			continue;
 needs_gc_run:
-		if (nft_set_elem_mark_busy(&he->ext))
-			continue;
+		nft_set_elem_dead(&he->ext);
+dead_elem:
+		gc = nft_trans_gc_queue_async(gc, gc_seq, GFP_ATOMIC);
+		if (!gc)
+			goto try_later;
 
-		gcb = nft_set_gc_batch_check(set, gcb, GFP_ATOMIC);
-		if (gcb == NULL)
-			break;
-		rhashtable_remove_fast(&priv->ht, &he->node, nft_rhash_params);
-		atomic_dec(&set->nelems);
-		nft_set_gc_batch_add(gcb, he);
+		/* annotate gc sequence for this attempt. */
+		he->wq_gc_seq = priv->wq_gc_seq;
+		nft_trans_gc_elem_add(gc, he);
 	}
+
+	gc = nft_trans_gc_catchall_async(gc, gc_seq);
+
+try_later:
+	/* catchall list iteration requires rcu read side lock. */
 	rhashtable_walk_stop(&hti);
 	rhashtable_walk_exit(&hti);
 
-	he = nft_set_catchall_gc(set);
-	if (he) {
-		gcb = nft_set_gc_batch_check(set, gcb, GFP_ATOMIC);
-		if (gcb)
-			nft_set_gc_batch_add(gcb, he);
-	}
-	nft_set_gc_batch_complete(gcb);
+	if (gc)
+		nft_trans_gc_queue_async_done(gc);
+
+done:
 	queue_delayed_work(system_power_efficient_wq, &priv->gc_work,
 			   nft_set_gc_interval(set));
 }
@@ -392,25 +435,36 @@
 		return err;
 
 	INIT_DEFERRABLE_WORK(&priv->gc_work, nft_rhash_gc);
-	if (set->flags & NFT_SET_TIMEOUT)
+	if (set->flags & (NFT_SET_TIMEOUT | NFT_SET_EVAL))
 		nft_rhash_gc_init(set);
 
 	return 0;
 }
 
+struct nft_rhash_ctx {
+	const struct nft_ctx	ctx;
+	const struct nft_set	*set;
+};
+
 static void nft_rhash_elem_destroy(void *ptr, void *arg)
 {
-	nft_set_elem_destroy(arg, ptr, true);
+	struct nft_rhash_ctx *rhash_ctx = arg;
+
+	nf_tables_set_elem_destroy(&rhash_ctx->ctx, rhash_ctx->set, ptr);
 }
 
-static void nft_rhash_destroy(const struct nft_set *set)
+static void nft_rhash_destroy(const struct nft_ctx *ctx,
+			      const struct nft_set *set)
 {
 	struct nft_rhash *priv = nft_set_priv(set);
+	struct nft_rhash_ctx rhash_ctx = {
+		.ctx	= *ctx,
+		.set	= set,
+	};
 
 	cancel_delayed_work_sync(&priv->gc_work);
-	rcu_barrier();
 	rhashtable_free_and_destroy(&priv->ht, nft_rhash_elem_destroy,
-				    (void *)set);
+				    (void *)&rhash_ctx);
 }
 
 /* Number of buckets is stored in u32, so cap our result to 1U<<31 */
@@ -554,7 +608,7 @@
 {
 	struct nft_hash_elem *he = elem->priv;
 
-	nft_set_elem_change_active(net, set, &he->ext);
+	nft_clear(net, &he->ext);
 }
 
 static bool nft_hash_flush(const struct net *net,
@@ -608,8 +662,6 @@
 		hlist_for_each_entry_rcu(he, &priv->table[i], node) {
 			if (iter->count < iter->skip)
 				goto cont;
-			if (!nft_set_elem_active(&he->ext, iter->genmask))
-				goto cont;
 
 			elem.priv = he;
 
@@ -641,7 +693,8 @@
 	return 0;
 }
 
-static void nft_hash_destroy(const struct nft_set *set)
+static void nft_hash_destroy(const struct nft_ctx *ctx,
+			     const struct nft_set *set)
 {
 	struct nft_hash *priv = nft_set_priv(set);
 	struct nft_hash_elem *he;
@@ -651,7 +704,7 @@
 	for (i = 0; i < priv->buckets; i++) {
 		hlist_for_each_entry_safe(he, next, &priv->table[i], node) {
 			hlist_del_rcu(&he->node);
-			nft_set_elem_destroy(set, he, true);
+			nf_tables_set_elem_destroy(ctx, set, he);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_set_pipapo.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_set_pipapo.c
@@ -342,9 +342,6 @@
 #include "nft_set_pipapo_avx2.h"
 #include "nft_set_pipapo.h"
 
-/* Current working bitmap index, toggled between field matches */
-static DEFINE_PER_CPU(bool, nft_pipapo_scratch_index);
-
 /**
  * pipapo_refill() - For each set bit, set bits from selected mapping table item
  * @map:	Bitmap to be scanned for set bits
@@ -363,7 +360,7 @@
  * Return: -1 on no match, bit position on 'match_only', 0 otherwise.
  */
 int pipapo_refill(unsigned long *map, int len, int rules, unsigned long *dst,
-		  union nft_pipapo_map_bucket *mt, bool match_only)
+		  const union nft_pipapo_map_bucket *mt, bool match_only)
 {
 	unsigned long bitset;
 	int k, ret = -1;
@@ -412,27 +409,30 @@
 		       const u32 *key, const struct nft_set_ext **ext)
 {
 	struct nft_pipapo *priv = nft_set_priv(set);
+	struct nft_pipapo_scratch *scratch;
 	unsigned long *res_map, *fill_map;
 	u8 genmask = nft_genmask_cur(net);
+	const struct nft_pipapo_match *m;
+	const struct nft_pipapo_field *f;
 	const u8 *rp = (const u8 *)key;
-	struct nft_pipapo_match *m;
-	struct nft_pipapo_field *f;
 	bool map_index;
 	int i;
 
 	local_bh_disable();
 
-	map_index = raw_cpu_read(nft_pipapo_scratch_index);
-
 	m = rcu_dereference(priv->match);
 
 	if (unlikely(!m || !*raw_cpu_ptr(m->scratch)))
 		goto out;
 
-	res_map  = *raw_cpu_ptr(m->scratch) + (map_index ? m->bsize_max : 0);
-	fill_map = *raw_cpu_ptr(m->scratch) + (map_index ? 0 : m->bsize_max);
+	scratch = *raw_cpu_ptr(m->scratch);
+
+	map_index = scratch->map_index;
+
+	res_map  = scratch->map + (map_index ? m->bsize_max : 0);
+	fill_map = scratch->map + (map_index ? 0 : m->bsize_max);
 
-	memset(res_map, 0xff, m->bsize_max * sizeof(*res_map));
+	pipapo_resmap_init(m, res_map);
 
 	nft_pipapo_for_each_field(f, i, m) {
 		bool last = i == m->field_count - 1;
@@ -460,7 +460,7 @@
 		b = pipapo_refill(res_map, f->bsize, f->rules, fill_map, f->mt,
 				  last);
 		if (b < 0) {
-			raw_cpu_write(nft_pipapo_scratch_index, map_index);
+			scratch->map_index = map_index;
 			local_bh_enable();
 
 			return false;
@@ -477,7 +477,7 @@
 			 * current inactive bitmap is clean and can be reused as
 			 * *next* bitmap (not initial) for the next packet.
 			 */
-			raw_cpu_write(nft_pipapo_scratch_index, map_index);
+			scratch->map_index = map_index;
 			local_bh_enable();
 
 			return true;
@@ -504,6 +504,7 @@
  * @set:	nftables API set representation
  * @data:	Key data to be matched against existing elements
  * @genmask:	If set, check that element is active in given genmask
+ * @tstamp:	timestamp to check for expired elements
  *
  * This is essentially the same as the lookup function, except that it matches
  * key data against the uncommitted copy and doesn't use preallocated maps for
@@ -513,15 +514,18 @@
  */
 static struct nft_pipapo_elem *pipapo_get(const struct net *net,
 					  const struct nft_set *set,
-					  const u8 *data, u8 genmask)
+					  const u8 *data, u8 genmask,
+					  u64 tstamp)
 {
 	struct nft_pipapo_elem *ret = ERR_PTR(-ENOENT);
 	struct nft_pipapo *priv = nft_set_priv(set);
-	struct nft_pipapo_match *m = priv->clone;
 	unsigned long *res_map, *fill_map = NULL;
-	struct nft_pipapo_field *f;
+	const struct nft_pipapo_match *m;
+	const struct nft_pipapo_field *f;
 	int i;
 
+	m = priv->clone;
+
 	res_map = kmalloc_array(m->bsize_max, sizeof(*res_map), GFP_ATOMIC);
 	if (!res_map) {
 		ret = ERR_PTR(-ENOMEM);
@@ -534,7 +538,7 @@
 		goto out;
 	}
 
-	memset(res_map, 0xff, m->bsize_max * sizeof(*res_map));
+	pipapo_resmap_init(m, res_map);
 
 	nft_pipapo_for_each_field(f, i, m) {
 		bool last = i == m->field_count - 1;
@@ -566,8 +570,9 @@
 			goto out;
 
 		if (last) {
-			if (nft_set_elem_expired(&f->mt[b].e->ext) ||
-			    (genmask &&
+			if (__nft_set_elem_expired(&f->mt[b].e->ext, tstamp))
+				goto next_match;
+			if ((genmask &&
 			     !nft_set_elem_active(&f->mt[b].e->ext, genmask)))
 				goto next_match;
 
@@ -602,7 +607,7 @@
 			    const struct nft_set_elem *elem, unsigned int flags)
 {
 	return pipapo_get(net, set, (const u8 *)elem->key.val.data,
-			  nft_genmask_cur(net));
+			 nft_genmask_cur(net), get_jiffies_64());
 }
 
 /**
@@ -901,12 +906,14 @@
 static int pipapo_insert(struct nft_pipapo_field *f, const uint8_t *k,
 			 int mask_bits)
 {
-	int rule = f->rules++, group, ret, bit_offset = 0;
+	int rule = f->rules, group, ret, bit_offset = 0;
 
-	ret = pipapo_resize(f, f->rules - 1, f->rules);
+	ret = pipapo_resize(f, f->rules, f->rules + 1);
 	if (ret)
 		return ret;
 
+	f->rules++;
+
 	for (group = 0; group < f->groups; group++) {
 		int i, v;
 		u8 mask;
@@ -1051,7 +1058,9 @@
 			step++;
 			if (step >= len) {
 				if (!masks) {
-					pipapo_insert(f, base, 0);
+					err = pipapo_insert(f, base, 0);
+					if (err < 0)
+						return err;
 					masks = 1;
 				}
 				goto out;
@@ -1097,6 +1106,25 @@
 }
 
 /**
+ * pipapo_free_scratch() - Free per-CPU map at original (not aligned) address
+ * @m:		Matching data
+ * @cpu:	CPU number
+ */
+static void pipapo_free_scratch(const struct nft_pipapo_match *m, unsigned int cpu)
+{
+	struct nft_pipapo_scratch *s;
+	void *mem;
+
+	s = *per_cpu_ptr(m->scratch, cpu);
+	if (!s)
+		return;
+
+	mem = s;
+	mem -= s->align_off;
+	kfree(mem);
+}
+
+/**
  * pipapo_realloc_scratch() - Reallocate scratch maps for partial match results
  * @clone:	Copy of matching data with pending insertions and deletions
  * @bsize_max:	Maximum bucket size, scratch maps cover two buckets
@@ -1109,12 +1137,13 @@
 	int i;
 
 	for_each_possible_cpu(i) {
-		unsigned long *scratch;
+		struct nft_pipapo_scratch *scratch;
 #ifdef NFT_PIPAPO_ALIGN
-		unsigned long *scratch_aligned;
+		void *scratch_aligned;
+		u32 align_off;
 #endif
-
-		scratch = kzalloc_node(bsize_max * sizeof(*scratch) * 2 +
+		scratch = kzalloc_node(struct_size(scratch, map,
+						   bsize_max * 2) +
 				       NFT_PIPAPO_ALIGN_HEADROOM,
 				       GFP_KERNEL, cpu_to_node(i));
 		if (!scratch) {
@@ -1128,14 +1157,25 @@
 			return -ENOMEM;
 		}
 
-		kfree(*per_cpu_ptr(clone->scratch, i));
-
-		*per_cpu_ptr(clone->scratch, i) = scratch;
+		pipapo_free_scratch(clone, i);
 
 #ifdef NFT_PIPAPO_ALIGN
-		scratch_aligned = NFT_PIPAPO_LT_ALIGN(scratch);
-		*per_cpu_ptr(clone->scratch_aligned, i) = scratch_aligned;
+		/* Align &scratch->map (not the struct itself): the extra
+		 * %NFT_PIPAPO_ALIGN_HEADROOM bytes passed to kzalloc_node()
+		 * above guarantee we can waste up to those bytes in order
+		 * to align the map field regardless of its offset within
+		 * the struct.
+		 */
+		BUILD_BUG_ON(offsetof(struct nft_pipapo_scratch, map) > NFT_PIPAPO_ALIGN_HEADROOM);
+
+		scratch_aligned = NFT_PIPAPO_LT_ALIGN(&scratch->map);
+		scratch_aligned -= offsetof(struct nft_pipapo_scratch, map);
+		align_off = scratch_aligned - (void *)scratch;
+
+		scratch = scratch_aligned;
+		scratch->align_off = align_off;
 #endif
+		*per_cpu_ptr(clone->scratch, i) = scratch;
 	}
 
 	return 0;
@@ -1161,7 +1201,9 @@
 	struct nft_pipapo *priv = nft_set_priv(set);
 	struct nft_pipapo_match *m = priv->clone;
 	u8 genmask = nft_genmask_next(net);
+	u64 tstamp = nft_net_tstamp(net);
 	struct nft_pipapo_field *f;
+	const u8 *start_p, *end_p;
 	int i, bsize_max, err = 0;
 
 	if (nft_set_ext_exists(ext, NFT_SET_EXT_KEY_END))
@@ -1169,7 +1211,7 @@
 	else
 		end = start;
 
-	dup = pipapo_get(net, set, start, genmask);
+	dup = pipapo_get(net, set, start, genmask, tstamp);
 	if (!IS_ERR(dup)) {
 		/* Check if we already have the same exact entry */
 		const struct nft_data *dup_key, *dup_end;
@@ -1191,7 +1233,7 @@
 
 	if (PTR_ERR(dup) == -ENOENT) {
 		/* Look for partially overlapping entries */
-		dup = pipapo_get(net, set, end, nft_genmask_next(net));
+		dup = pipapo_get(net, set, end, nft_genmask_next(net), tstamp);
 	}
 
 	if (PTR_ERR(dup) != -ENOENT) {
@@ -1202,9 +1244,9 @@
 	}
 
 	/* Validate */
+	start_p = start;
+	end_p = end;
 	nft_pipapo_for_each_field(f, i, m) {
-		const u8 *start_p = start, *end_p = end;
-
 		if (f->rules >= (unsigned long)NFT_PIPAPO_RULE0_MAX)
 			return -ENOSPC;
 
@@ -1233,6 +1275,9 @@
 		else
 			ret = pipapo_expand(f, start, end, f->groups * f->bb);
 
+		if (ret < 0)
+			return ret;
+
 		if (f->bsize > bsize_max)
 			bsize_max = f->bsize;
 
@@ -1285,11 +1330,11 @@
 	if (!new->scratch)
 		goto out_scratch;
 
-#ifdef NFT_PIPAPO_ALIGN
-	new->scratch_aligned = alloc_percpu(*new->scratch_aligned);
-	if (!new->scratch_aligned)
-		goto out_scratch;
-#endif
+	for_each_possible_cpu(i)
+		*per_cpu_ptr(new->scratch, i) = NULL;
+
+	if (pipapo_realloc_scratch(new, old->bsize_max))
+		goto out_scratch_realloc;
 
 	rcu_head_init(&new->rcu);
 
@@ -1334,9 +1379,9 @@
 		kvfree(dst->lt);
 		dst--;
 	}
-#ifdef NFT_PIPAPO_ALIGN
-	free_percpu(new->scratch_aligned);
-#endif
+out_scratch_realloc:
+	for_each_possible_cpu(i)
+		pipapo_free_scratch(new, i);
 out_scratch:
 	free_percpu(new->scratch);
 	kfree(new);
@@ -1520,20 +1565,39 @@
 	}
 }
 
+static void nft_pipapo_gc_deactivate(struct net *net, struct nft_set *set,
+				     struct nft_pipapo_elem *e)
+
+{
+	struct nft_set_elem elem = {
+		.priv	= e,
+	};
+
+	nft_setelem_data_deactivate(net, set, &elem);
+}
+
 /**
  * pipapo_gc() - Drop expired entries from set, destroy start and end elements
- * @set:	nftables API set representation
+ * @_set:	nftables API set representation
  * @m:		Matching data
  */
-static void pipapo_gc(const struct nft_set *set, struct nft_pipapo_match *m)
+static void pipapo_gc(const struct nft_set *_set, struct nft_pipapo_match *m)
 {
+	struct nft_set *set = (struct nft_set *) _set;
 	struct nft_pipapo *priv = nft_set_priv(set);
+	struct net *net = read_pnet(&set->net);
+	u64 tstamp = nft_net_tstamp(net);
 	int rules_f0, first_rule = 0;
 	struct nft_pipapo_elem *e;
+	struct nft_trans_gc *gc;
+
+	gc = nft_trans_gc_alloc(set, 0, GFP_KERNEL);
+	if (!gc)
+		return;
 
 	while ((rules_f0 = pipapo_rules_same_key(m->f, first_rule))) {
 		union nft_pipapo_map_bucket rulemap[NFT_PIPAPO_MAX_FIELDS];
-		struct nft_pipapo_field *f;
+		const struct nft_pipapo_field *f;
 		int i, start, rules_fx;
 
 		start = first_rule;
@@ -1553,13 +1617,20 @@
 		f--;
 		i--;
 		e = f->mt[rulemap[i].to].e;
-		if (nft_set_elem_expired(&e->ext) &&
-		    !nft_set_elem_mark_busy(&e->ext)) {
+
+		/* synchronous gc never fails, there is no need to set on
+		 * NFT_SET_ELEM_DEAD_BIT.
+		 */
+		if (__nft_set_elem_expired(&e->ext, tstamp)) {
 			priv->dirty = true;
-			pipapo_drop(m, rulemap);
 
-			rcu_barrier();
-			nft_set_elem_destroy(set, e, true);
+			gc = nft_trans_gc_queue_sync(gc, GFP_ATOMIC);
+			if (!gc)
+				return;
+
+			nft_pipapo_gc_deactivate(net, set, e);
+			pipapo_drop(m, rulemap);
+			nft_trans_gc_elem_add(gc, e);
 
 			/* And check again current first rule, which is now the
 			 * first we haven't checked.
@@ -1569,11 +1640,11 @@
 		}
 	}
 
-	e = nft_set_catchall_gc(set);
-	if (e)
-		nft_set_elem_destroy(set, e, true);
-
-	priv->last_gc = jiffies;
+	gc = nft_trans_gc_catchall_sync(gc);
+	if (gc) {
+		nft_trans_gc_queue_sync_done(gc);
+		priv->last_gc = jiffies;
+	}
 }
 
 /**
@@ -1591,32 +1662,33 @@
 	}
 }
 
-/**
- * pipapo_reclaim_match - RCU callback to free fields from old matching data
- * @rcu:	RCU head
- */
-static void pipapo_reclaim_match(struct rcu_head *rcu)
+static void pipapo_free_match(struct nft_pipapo_match *m)
 {
-	struct nft_pipapo_match *m;
 	int i;
 
-	m = container_of(rcu, struct nft_pipapo_match, rcu);
-
 	for_each_possible_cpu(i)
-		kfree(*per_cpu_ptr(m->scratch, i));
+		pipapo_free_scratch(m, i);
 
-#ifdef NFT_PIPAPO_ALIGN
-	free_percpu(m->scratch_aligned);
-#endif
 	free_percpu(m->scratch);
-
 	pipapo_free_fields(m);
 
 	kfree(m);
 }
 
 /**
- * pipapo_commit() - Replace lookup data with current working copy
+ * pipapo_reclaim_match - RCU callback to free fields from old matching data
+ * @rcu:	RCU head
+ */
+static void pipapo_reclaim_match(struct rcu_head *rcu)
+{
+	struct nft_pipapo_match *m;
+
+	m = container_of(rcu, struct nft_pipapo_match, rcu);
+	pipapo_free_match(m);
+}
+
+/**
+ * nft_pipapo_commit() - Replace lookup data with current working copy
  * @set:	nftables API set representation
  *
  * While at it, check if we should perform garbage collection on the working
@@ -1626,7 +1698,7 @@
  * We also need to create a new working copy for subsequent insertions and
  * deletions.
  */
-static void pipapo_commit(const struct nft_set *set)
+static void nft_pipapo_commit(const struct nft_set *set)
 {
 	struct nft_pipapo *priv = nft_set_priv(set);
 	struct nft_pipapo_match *new_clone, *old;
@@ -1651,6 +1723,37 @@
 	priv->clone = new_clone;
 }
 
+static bool nft_pipapo_transaction_mutex_held(const struct nft_set *set)
+{
+#ifdef CONFIG_PROVE_LOCKING
+	const struct net *net = read_pnet(&set->net);
+
+	return lockdep_is_held(&nft_pernet(net)->commit_mutex);
+#else
+	return true;
+#endif
+}
+
+static void nft_pipapo_abort(const struct nft_set *set)
+{
+	struct nft_pipapo *priv = nft_set_priv(set);
+	struct nft_pipapo_match *new_clone, *m;
+
+	if (!priv->dirty)
+		return;
+
+	m = rcu_dereference_protected(priv->match, nft_pipapo_transaction_mutex_held(set));
+
+	new_clone = pipapo_clone(m);
+	if (IS_ERR(new_clone))
+		return;
+
+	priv->dirty = false;
+
+	pipapo_free_match(priv->clone);
+	priv->clone = new_clone;
+}
+
 /**
  * nft_pipapo_activate() - Mark element reference as active given key, commit
  * @net:	Network namespace
@@ -1658,8 +1761,7 @@
  * @elem:	nftables API element representation containing key data
  *
  * On insertion, elements are added to a copy of the matching data currently
- * in use for lookups, and not directly inserted into current lookup data, so
- * we'll take care of that by calling pipapo_commit() here. Both
+ * in use for lookups, and not directly inserted into current lookup data. Both
  * nft_pipapo_insert() and nft_pipapo_activate() are called once for each
  * element, hence we can't purpose either one as a real commit operation.
  */
@@ -1667,16 +1769,9 @@
 				const struct nft_set *set,
 				const struct nft_set_elem *elem)
 {
-	struct nft_pipapo_elem *e;
-
-	e = pipapo_get(net, set, (const u8 *)elem->key.val.data, 0);
-	if (IS_ERR(e))
-		return;
-
-	nft_set_elem_change_active(net, set, &e->ext);
-	nft_set_elem_clear_busy(&e->ext);
+	struct nft_pipapo_elem *e = elem->priv;
 
-	pipapo_commit(set);
+	nft_clear(net, &e->ext);
 }
 
 /**
@@ -1697,7 +1792,7 @@
 {
 	struct nft_pipapo_elem *e;
 
-	e = pipapo_get(net, set, data, nft_genmask_next(net));
+	e = pipapo_get(net, set, data, nft_genmask_next(net), nft_net_tstamp(net));
 	if (IS_ERR(e))
 		return NULL;
 
@@ -1888,10 +1983,6 @@
 
 	data = (const u8 *)nft_set_ext_key(&e->ext);
 
-	e = pipapo_get(net, set, data, 0);
-	if (IS_ERR(e))
-		return;
-
 	while ((rules_f0 = pipapo_rules_same_key(m->f, first_rule))) {
 		union nft_pipapo_map_bucket rulemap[NFT_PIPAPO_MAX_FIELDS];
 		const u8 *match_start, *match_end;
@@ -1899,12 +1990,18 @@
 		int i, start, rules_fx;
 
 		match_start = data;
-		match_end = (const u8 *)nft_set_ext_key_end(&e->ext)->data;
+
+		if (nft_set_ext_exists(&e->ext, NFT_SET_EXT_KEY_END))
+			match_end = (const u8 *)nft_set_ext_key_end(&e->ext)->data;
+		else
+			match_end = data;
 
 		start = first_rule;
 		rules_fx = rules_f0;
 
 		nft_pipapo_for_each_field(f, i, m) {
+			bool last = i == m->field_count - 1;
+
 			if (!pipapo_match_field(f, start, rules_fx,
 						match_start, match_end))
 				break;
@@ -1917,17 +2014,18 @@
 
 			match_start += NFT_PIPAPO_GROUPS_PADDED_SIZE(f);
 			match_end += NFT_PIPAPO_GROUPS_PADDED_SIZE(f);
-		}
 
-		if (i == m->field_count) {
-			priv->dirty = true;
-			pipapo_drop(m, rulemap);
-			pipapo_commit(set);
-			return;
+			if (last && f->mt[rulemap[i].to].e == e) {
+				priv->dirty = true;
+				pipapo_drop(m, rulemap);
+				return;
+			}
 		}
 
 		first_rule += rules_f0;
 	}
+
+	WARN_ON_ONCE(1); /* elem_priv not found */
 }
 
 /**
@@ -1944,12 +2042,18 @@
 			    struct nft_set_iter *iter)
 {
 	struct nft_pipapo *priv = nft_set_priv(set);
-	struct nft_pipapo_match *m;
-	struct nft_pipapo_field *f;
+	const struct nft_pipapo_match *m;
+	const struct nft_pipapo_field *f;
 	int i, r;
 
+	WARN_ON_ONCE(iter->type != NFT_ITER_READ &&
+		     iter->type != NFT_ITER_UPDATE);
+
 	rcu_read_lock();
-	m = rcu_dereference(priv->match);
+	if (iter->type == NFT_ITER_READ)
+		m = rcu_dereference(priv->match);
+	else
+		m = priv->clone;
 
 	if (unlikely(!m))
 		goto out;
@@ -1968,8 +2072,6 @@
 			goto cont;
 
 		e = f->mt[r].e;
-		if (nft_set_elem_expired(&e->ext))
-			goto cont;
 
 		elem.priv = e;
 
@@ -2058,7 +2160,7 @@
 	m->field_count = field_count;
 	m->bsize_max = 0;
 
-	m->scratch = alloc_percpu(unsigned long *);
+	m->scratch = alloc_percpu(struct nft_pipapo_scratch *);
 	if (!m->scratch) {
 		err = -ENOMEM;
 		goto out_scratch;
@@ -2066,16 +2168,6 @@
 	for_each_possible_cpu(i)
 		*per_cpu_ptr(m->scratch, i) = NULL;
 
-#ifdef NFT_PIPAPO_ALIGN
-	m->scratch_aligned = alloc_percpu(unsigned long *);
-	if (!m->scratch_aligned) {
-		err = -ENOMEM;
-		goto out_free;
-	}
-	for_each_possible_cpu(i)
-		*per_cpu_ptr(m->scratch_aligned, i) = NULL;
-#endif
-
 	rcu_head_init(&m->rcu);
 
 	nft_pipapo_for_each_field(f, i, m) {
@@ -2106,9 +2198,6 @@
 	return 0;
 
 out_free:
-#ifdef NFT_PIPAPO_ALIGN
-	free_percpu(m->scratch_aligned);
-#endif
 	free_percpu(m->scratch);
 out_scratch:
 	kfree(m);
@@ -2117,39 +2206,51 @@
 }
 
 /**
- * nft_pipapo_destroy() - Free private data for set and all committed elements
+ * nft_set_pipapo_match_destroy() - Destroy elements from key mapping array
+ * @ctx:	context
  * @set:	nftables API set representation
+ * @m:		matching data pointing to key mapping array
  */
-static void nft_pipapo_destroy(const struct nft_set *set)
+static void nft_set_pipapo_match_destroy(const struct nft_ctx *ctx,
+					 const struct nft_set *set,
+					 struct nft_pipapo_match *m)
 {
-	struct nft_pipapo *priv = nft_set_priv(set);
-	struct nft_pipapo_match *m;
 	struct nft_pipapo_field *f;
-	int i, r, cpu;
+	int i, r;
 
-	m = rcu_dereference_protected(priv->match, true);
-	if (m) {
-		rcu_barrier();
+	for (i = 0, f = m->f; i < m->field_count - 1; i++, f++)
+		;
 
-		for (i = 0, f = m->f; i < m->field_count - 1; i++, f++)
-			;
+	for (r = 0; r < f->rules; r++) {
+		struct nft_pipapo_elem *e;
 
-		for (r = 0; r < f->rules; r++) {
-			struct nft_pipapo_elem *e;
+		if (r < f->rules - 1 && f->mt[r + 1].e == f->mt[r].e)
+			continue;
 
-			if (r < f->rules - 1 && f->mt[r + 1].e == f->mt[r].e)
-				continue;
+		e = f->mt[r].e;
 
-			e = f->mt[r].e;
+		nf_tables_set_elem_destroy(ctx, set, e);
+	}
+}
 
-			nft_set_elem_destroy(set, e, true);
-		}
+/**
+ * nft_pipapo_destroy() - Free private data for set and all committed elements
+ * @ctx:	context
+ * @set:	nftables API set representation
+ */
+static void nft_pipapo_destroy(const struct nft_ctx *ctx,
+			       const struct nft_set *set)
+{
+	struct nft_pipapo *priv = nft_set_priv(set);
+	struct nft_pipapo_match *m;
+	int cpu;
+
+	m = rcu_dereference_protected(priv->match, true);
+	if (m) {
+		rcu_barrier();
 
-#ifdef NFT_PIPAPO_ALIGN
-		free_percpu(m->scratch_aligned);
-#endif
 		for_each_possible_cpu(cpu)
-			kfree(*per_cpu_ptr(m->scratch, cpu));
+			pipapo_free_scratch(m, cpu);
 		free_percpu(m->scratch);
 		pipapo_free_fields(m);
 		kfree(m);
@@ -2157,11 +2258,12 @@
 	}
 
 	if (priv->clone) {
-#ifdef NFT_PIPAPO_ALIGN
-		free_percpu(priv->clone->scratch_aligned);
-#endif
+		m = priv->clone;
+
+		nft_set_pipapo_match_destroy(ctx, set, m);
+
 		for_each_possible_cpu(cpu)
-			kfree(*per_cpu_ptr(priv->clone->scratch, cpu));
+			pipapo_free_scratch(priv->clone, cpu);
 		free_percpu(priv->clone->scratch);
 
 		pipapo_free_fields(priv->clone);
@@ -2203,6 +2305,8 @@
 		.init		= nft_pipapo_init,
 		.destroy	= nft_pipapo_destroy,
 		.gc_init	= nft_pipapo_gc_init,
+		.commit		= nft_pipapo_commit,
+		.abort		= nft_pipapo_abort,
 		.elemsize	= offsetof(struct nft_pipapo_elem, ext),
 	},
 };
@@ -2225,6 +2329,8 @@
 		.init		= nft_pipapo_init,
 		.destroy	= nft_pipapo_destroy,
 		.gc_init	= nft_pipapo_gc_init,
+		.commit		= nft_pipapo_commit,
+		.abort		= nft_pipapo_abort,
 		.elemsize	= offsetof(struct nft_pipapo_elem, ext),
 	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_set_pipapo.h
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_set_pipapo.h
@@ -131,20 +131,28 @@
 };
 
 /**
+ * struct nft_pipapo_scratch - percpu data used for lookup and matching
+ * @map_index:	Current working bitmap index, toggled between field matches
+ * @align_off:	Offset to get the originally allocated address
+ * @map:	store partial matching results during lookup
+ */
+struct nft_pipapo_scratch {
+	u8 map_index;
+	u32 align_off;
+	unsigned long map[];
+};
+
+/**
  * struct nft_pipapo_match - Data used for lookup and matching
  * @field_count		Amount of fields in set
  * @scratch:		Preallocated per-CPU maps for partial matching results
- * @scratch_aligned:	Version of @scratch aligned to NFT_PIPAPO_ALIGN bytes
  * @bsize_max:		Maximum lookup table bucket size of all fields, in longs
  * @rcu			Matching data is swapped on commits
  * @f:			Fields, with lookup and mapping tables
  */
 struct nft_pipapo_match {
 	int field_count;
-#ifdef NFT_PIPAPO_ALIGN
-	unsigned long * __percpu *scratch_aligned;
-#endif
-	unsigned long * __percpu *scratch;
+	struct nft_pipapo_scratch * __percpu *scratch;
 	size_t bsize_max;
 	struct rcu_head rcu;
 	struct nft_pipapo_field f[];
@@ -177,7 +185,7 @@
 };
 
 int pipapo_refill(unsigned long *map, int len, int rules, unsigned long *dst,
-		  union nft_pipapo_map_bucket *mt, bool match_only);
+		  const union nft_pipapo_map_bucket *mt, bool match_only);
 
 /**
  * pipapo_and_field_buckets_4bit() - Intersect 4-bit buckets
@@ -185,7 +193,7 @@
  * @dst:	Area to store result
  * @data:	Input data selecting table buckets
  */
-static inline void pipapo_and_field_buckets_4bit(struct nft_pipapo_field *f,
+static inline void pipapo_and_field_buckets_4bit(const struct nft_pipapo_field *f,
 						 unsigned long *dst,
 						 const u8 *data)
 {
@@ -213,7 +221,7 @@
  * @dst:	Area to store result
  * @data:	Input data selecting table buckets
  */
-static inline void pipapo_and_field_buckets_8bit(struct nft_pipapo_field *f,
+static inline void pipapo_and_field_buckets_8bit(const struct nft_pipapo_field *f,
 						 unsigned long *dst,
 						 const u8 *data)
 {
@@ -277,4 +285,25 @@
 	return size;
 }
 
+/**
+ * pipapo_resmap_init() - Initialise result map before first use
+ * @m:		Matching data, including mapping table
+ * @res_map:	Result map
+ *
+ * Initialize all bits covered by the first field to one, so that after
+ * the first step, only the matching bits of the first bit group remain.
+ *
+ * If other fields have a large bitmap, set remainder of res_map to 0.
+ */
+static inline void pipapo_resmap_init(const struct nft_pipapo_match *m, unsigned long *res_map)
+{
+	const struct nft_pipapo_field *f = m->f;
+	int i;
+
+	for (i = 0; i < f->bsize; i++)
+		res_map[i] = ULONG_MAX;
+
+	for (i = f->bsize; i < m->bsize_max; i++)
+		res_map[i] = 0ul;
+}
 #endif /* _NFT_SET_PIPAPO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_set_pipapo_avx2.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_set_pipapo_avx2.c
@@ -71,9 +71,6 @@
 #define NFT_PIPAPO_AVX2_ZERO(reg)					\
 	asm volatile("vpxor %ymm" #reg ", %ymm" #reg ", %ymm" #reg)
 
-/* Current working bitmap index, toggled between field matches */
-static DEFINE_PER_CPU(bool, nft_pipapo_avx2_scratch_index);
-
 /**
  * nft_pipapo_avx2_prepare() - Prepare before main algorithm body
  *
@@ -215,8 +212,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_4b_2(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	u8 pg[2] = { pkt[0] >> 4, pkt[0] & 0xf };
@@ -277,8 +275,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_4b_4(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	u8 pg[4] = { pkt[0] >> 4, pkt[0] & 0xf, pkt[1] >> 4, pkt[1] & 0xf };
@@ -353,8 +352,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_4b_8(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	u8 pg[8] = {  pkt[0] >> 4,  pkt[0] & 0xf,  pkt[1] >> 4,  pkt[1] & 0xf,
 		      pkt[2] >> 4,  pkt[2] & 0xf,  pkt[3] >> 4,  pkt[3] & 0xf,
@@ -448,8 +448,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_4b_12(unsigned long *map, unsigned long *fill,
-				        struct nft_pipapo_field *f, int offset,
-				        const u8 *pkt, bool first, bool last)
+					const struct nft_pipapo_field *f,
+					int offset, const u8 *pkt,
+					bool first, bool last)
 {
 	u8 pg[12] = {  pkt[0] >> 4,  pkt[0] & 0xf,  pkt[1] >> 4,  pkt[1] & 0xf,
 		       pkt[2] >> 4,  pkt[2] & 0xf,  pkt[3] >> 4,  pkt[3] & 0xf,
@@ -537,8 +538,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_4b_32(unsigned long *map, unsigned long *fill,
-					struct nft_pipapo_field *f, int offset,
-					const u8 *pkt, bool first, bool last)
+					const struct nft_pipapo_field *f,
+					int offset, const u8 *pkt,
+					bool first, bool last)
 {
 	u8 pg[32] = {  pkt[0] >> 4,  pkt[0] & 0xf,  pkt[1] >> 4,  pkt[1] & 0xf,
 		       pkt[2] >> 4,  pkt[2] & 0xf,  pkt[3] >> 4,  pkt[3] & 0xf,
@@ -672,8 +674,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_8b_1(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	unsigned long *lt = f->lt, bsize = f->bsize;
@@ -729,8 +732,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_8b_2(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	unsigned long *lt = f->lt, bsize = f->bsize;
@@ -793,8 +797,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_8b_4(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	unsigned long *lt = f->lt, bsize = f->bsize;
@@ -868,8 +873,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_8b_6(unsigned long *map, unsigned long *fill,
-				       struct nft_pipapo_field *f, int offset,
-				       const u8 *pkt, bool first, bool last)
+				       const struct nft_pipapo_field *f,
+				       int offset, const u8 *pkt,
+				       bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	unsigned long *lt = f->lt, bsize = f->bsize;
@@ -886,7 +892,7 @@
 			NFT_PIPAPO_AVX2_BUCKET_LOAD8(4,  lt, 4, pkt[4], bsize);
 
 			NFT_PIPAPO_AVX2_AND(5, 0, 1);
-			NFT_PIPAPO_AVX2_BUCKET_LOAD8(6,  lt, 6, pkt[5], bsize);
+			NFT_PIPAPO_AVX2_BUCKET_LOAD8(6,  lt, 5, pkt[5], bsize);
 			NFT_PIPAPO_AVX2_AND(7, 2, 3);
 
 			/* Stall */
@@ -953,8 +959,9 @@
  * word index to be checked next (i.e. first filled word).
  */
 static int nft_pipapo_avx2_lookup_8b_16(unsigned long *map, unsigned long *fill,
-					struct nft_pipapo_field *f, int offset,
-					const u8 *pkt, bool first, bool last)
+					const struct nft_pipapo_field *f,
+					int offset, const u8 *pkt,
+					bool first, bool last)
 {
 	int i, ret = -1, m256_size = f->bsize / NFT_PIPAPO_LONGS_PER_M256, b;
 	unsigned long *lt = f->lt, bsize = f->bsize;
@@ -1029,6 +1036,7 @@
 
 /**
  * nft_pipapo_avx2_lookup_slow() - Fallback function for uncommon field sizes
+ * @mdata:	Matching data, including mapping table
  * @map:	Previous match result, used as initial bitmap
  * @fill:	Destination bitmap to be filled with current match result
  * @f:		Field, containing lookup and mapping tables
@@ -1044,9 +1052,11 @@
  * Return: -1 on no match, rule index of match if @last, otherwise first long
  * word index to be checked next (i.e. first filled word).
  */
-static int nft_pipapo_avx2_lookup_slow(unsigned long *map, unsigned long *fill,
-					struct nft_pipapo_field *f, int offset,
-					const u8 *pkt, bool first, bool last)
+static int nft_pipapo_avx2_lookup_slow(const struct nft_pipapo_match *mdata,
+					unsigned long *map, unsigned long *fill,
+					const struct nft_pipapo_field *f,
+					int offset, const u8 *pkt,
+					bool first, bool last)
 {
 	unsigned long *lt = f->lt, bsize = f->bsize;
 	int i, ret = -1, b;
@@ -1054,7 +1064,7 @@
 	lt += offset * NFT_PIPAPO_LONGS_PER_M256;
 
 	if (first)
-		memset(map, 0xff, bsize * sizeof(*map));
+		pipapo_resmap_init(mdata, map);
 
 	for (i = offset; i < bsize; i++) {
 		if (f->bb == 8)
@@ -1122,16 +1132,23 @@
 			    const u32 *key, const struct nft_set_ext **ext)
 {
 	struct nft_pipapo *priv = nft_set_priv(set);
-	unsigned long *res, *fill, *scratch;
+	struct nft_pipapo_scratch *scratch;
 	u8 genmask = nft_genmask_cur(net);
+	const struct nft_pipapo_match *m;
+	const struct nft_pipapo_field *f;
 	const u8 *rp = (const u8 *)key;
-	struct nft_pipapo_match *m;
-	struct nft_pipapo_field *f;
+	unsigned long *res, *fill;
 	bool map_index;
 	int i, ret = 0;
 
-	if (unlikely(!irq_fpu_usable()))
-		return nft_pipapo_lookup(net, set, key, ext);
+	local_bh_disable();
+
+	if (unlikely(!irq_fpu_usable())) {
+		bool fallback_res = nft_pipapo_lookup(net, set, key, ext);
+
+		local_bh_enable();
+		return fallback_res;
+	}
 
 	m = rcu_dereference(priv->match);
 
@@ -1143,15 +1160,17 @@
 	 */
 	kernel_fpu_begin_mask(0);
 
-	scratch = *raw_cpu_ptr(m->scratch_aligned);
+	scratch = *raw_cpu_ptr(m->scratch);
 	if (unlikely(!scratch)) {
 		kernel_fpu_end();
+		local_bh_enable();
 		return false;
 	}
-	map_index = raw_cpu_read(nft_pipapo_avx2_scratch_index);
 
-	res  = scratch + (map_index ? m->bsize_max : 0);
-	fill = scratch + (map_index ? 0 : m->bsize_max);
+	map_index = scratch->map_index;
+
+	res  = scratch->map + (map_index ? m->bsize_max : 0);
+	fill = scratch->map + (map_index ? 0 : m->bsize_max);
 
 	/* Starting map doesn't need to be set for this implementation */
 
@@ -1178,7 +1197,7 @@
 			} else if (f->groups == 16) {
 				NFT_SET_PIPAPO_AVX2_LOOKUP(8, 16);
 			} else {
-				ret = nft_pipapo_avx2_lookup_slow(res, fill, f,
+				ret = nft_pipapo_avx2_lookup_slow(m, res, fill, f,
 								  ret, rp,
 								  first, last);
 			}
@@ -1194,7 +1213,7 @@
 			} else if (f->groups == 32) {
 				NFT_SET_PIPAPO_AVX2_LOOKUP(4, 32);
 			} else {
-				ret = nft_pipapo_avx2_lookup_slow(res, fill, f,
+				ret = nft_pipapo_avx2_lookup_slow(m, res, fill, f,
 								  ret, rp,
 								  first, last);
 			}
@@ -1223,8 +1242,9 @@
 
 out:
 	if (i % 2)
-		raw_cpu_write(nft_pipapo_avx2_scratch_index, !map_index);
+		scratch->map_index = !map_index;
 	kernel_fpu_end();
+	local_bh_enable();
 
 	return ret >= 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_set_rbtree.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_set_rbtree.c
@@ -38,10 +38,18 @@
 	return !nft_rbtree_interval_end(rbe);
 }
 
-static bool nft_rbtree_equal(const struct nft_set *set, const void *this,
-			     const struct nft_rbtree_elem *interval)
+static int nft_rbtree_cmp(const struct nft_set *set,
+			  const struct nft_rbtree_elem *e1,
+			  const struct nft_rbtree_elem *e2)
 {
-	return memcmp(this, nft_set_ext_key(&interval->ext), set->klen) == 0;
+	return memcmp(nft_set_ext_key(&e1->ext), nft_set_ext_key(&e2->ext),
+		      set->klen);
+}
+
+static bool nft_rbtree_elem_expired(const struct nft_rbtree_elem *rbe)
+{
+	return nft_set_elem_expired(&rbe->ext) ||
+	       nft_set_elem_is_dead(&rbe->ext);
 }
 
 static bool __nft_rbtree_lookup(const struct net *net, const struct nft_set *set,
@@ -52,7 +60,6 @@
 	const struct nft_rbtree_elem *rbe, *interval = NULL;
 	u8 genmask = nft_genmask_cur(net);
 	const struct rb_node *parent;
-	const void *this;
 	int d;
 
 	parent = rcu_dereference_raw(priv->root.rb_node);
@@ -62,12 +69,11 @@
 
 		rbe = rb_entry(parent, struct nft_rbtree_elem, node);
 
-		this = nft_set_ext_key(&rbe->ext);
-		d = memcmp(this, key, set->klen);
+		d = memcmp(nft_set_ext_key(&rbe->ext), key, set->klen);
 		if (d < 0) {
 			parent = rcu_dereference_raw(parent->rb_left);
 			if (interval &&
-			    nft_rbtree_equal(set, this, interval) &&
+			    !nft_rbtree_cmp(set, rbe, interval) &&
 			    nft_rbtree_interval_end(rbe) &&
 			    nft_rbtree_interval_start(interval))
 				continue;
@@ -80,7 +86,7 @@
 				continue;
 			}
 
-			if (nft_set_elem_expired(&rbe->ext))
+			if (nft_rbtree_elem_expired(rbe))
 				return false;
 
 			if (nft_rbtree_interval_end(rbe)) {
@@ -98,7 +104,7 @@
 
 	if (set->flags & NFT_SET_INTERVAL && interval != NULL &&
 	    nft_set_elem_active(&interval->ext, genmask) &&
-	    !nft_set_elem_expired(&interval->ext) &&
+	    !nft_rbtree_elem_expired(interval) &&
 	    nft_rbtree_interval_start(interval)) {
 		*ext = &interval->ext;
 		return true;
@@ -215,150 +221,264 @@
 	return rbe;
 }
 
+static void nft_rbtree_gc_remove(struct net *net, struct nft_set *set,
+				 struct nft_rbtree *priv,
+				 struct nft_rbtree_elem *rbe)
+{
+	struct nft_set_elem elem = {
+		.priv	= rbe,
+	};
+
+	nft_setelem_data_deactivate(net, set, &elem);
+	rb_erase(&rbe->node, &priv->root);
+}
+
+static const struct nft_rbtree_elem *
+nft_rbtree_gc_elem(const struct nft_set *__set, struct nft_rbtree *priv,
+		   struct nft_rbtree_elem *rbe)
+{
+	struct nft_set *set = (struct nft_set *)__set;
+	struct rb_node *prev = rb_prev(&rbe->node);
+	struct net *net = read_pnet(&set->net);
+	struct nft_rbtree_elem *rbe_prev;
+	struct nft_trans_gc *gc;
+
+	gc = nft_trans_gc_alloc(set, 0, GFP_ATOMIC);
+	if (!gc)
+		return ERR_PTR(-ENOMEM);
+
+	/* search for end interval coming before this element.
+	 * end intervals don't carry a timeout extension, they
+	 * are coupled with the interval start element.
+	 */
+	while (prev) {
+		rbe_prev = rb_entry(prev, struct nft_rbtree_elem, node);
+		if (nft_rbtree_interval_end(rbe_prev) &&
+		    nft_set_elem_active(&rbe_prev->ext, NFT_GENMASK_ANY))
+			break;
+
+		prev = rb_prev(prev);
+	}
+
+	rbe_prev = NULL;
+	if (prev) {
+		rbe_prev = rb_entry(prev, struct nft_rbtree_elem, node);
+		nft_rbtree_gc_remove(net, set, priv, rbe_prev);
+
+		/* There is always room in this trans gc for this element,
+		 * memory allocation never actually happens, hence, the warning
+		 * splat in such case. No need to set NFT_SET_ELEM_DEAD_BIT,
+		 * this is synchronous gc which never fails.
+		 */
+		gc = nft_trans_gc_queue_sync(gc, GFP_ATOMIC);
+		if (WARN_ON_ONCE(!gc))
+			return ERR_PTR(-ENOMEM);
+
+		nft_trans_gc_elem_add(gc, rbe_prev);
+	}
+
+	nft_rbtree_gc_remove(net, set, priv, rbe);
+	gc = nft_trans_gc_queue_sync(gc, GFP_ATOMIC);
+	if (WARN_ON_ONCE(!gc))
+		return ERR_PTR(-ENOMEM);
+
+	nft_trans_gc_elem_add(gc, rbe);
+
+	nft_trans_gc_queue_sync_done(gc);
+
+	return rbe_prev;
+}
+
+static bool nft_rbtree_update_first(const struct nft_set *set,
+				    struct nft_rbtree_elem *rbe,
+				    struct rb_node *first)
+{
+	struct nft_rbtree_elem *first_elem;
+
+	first_elem = rb_entry(first, struct nft_rbtree_elem, node);
+	/* this element is closest to where the new element is to be inserted:
+	 * update the first element for the node list path.
+	 */
+	if (nft_rbtree_cmp(set, rbe, first_elem) < 0)
+		return true;
+
+	return false;
+}
+
 static int __nft_rbtree_insert(const struct net *net, const struct nft_set *set,
 			       struct nft_rbtree_elem *new,
 			       struct nft_set_ext **ext)
 {
-	bool overlap = false, dup_end_left = false, dup_end_right = false;
+	struct nft_rbtree_elem *rbe, *rbe_le = NULL, *rbe_ge = NULL;
+	struct rb_node *node, *next, *parent, **p, *first = NULL;
 	struct nft_rbtree *priv = nft_set_priv(set);
+	u8 cur_genmask = nft_genmask_cur(net);
 	u8 genmask = nft_genmask_next(net);
-	struct nft_rbtree_elem *rbe;
-	struct rb_node *parent, **p;
+	u64 tstamp = nft_net_tstamp(net);
 	int d;
 
-	/* Detect overlaps as we descend the tree. Set the flag in these cases:
-	 *
-	 * a1. _ _ __>|  ?_ _ __|  (insert end before existing end)
-	 * a2. _ _ ___|  ?_ _ _>|  (insert end after existing end)
-	 * a3. _ _ ___? >|_ _ __|  (insert start before existing end)
-	 *
-	 * and clear it later on, as we eventually reach the points indicated by
-	 * '?' above, in the cases described below. We'll always meet these
-	 * later, locally, due to tree ordering, and overlaps for the intervals
-	 * that are the closest together are always evaluated last.
-	 *
-	 * b1. _ _ __>|  !_ _ __|  (insert end before existing start)
-	 * b2. _ _ ___|  !_ _ _>|  (insert end after existing start)
-	 * b3. _ _ ___! >|_ _ __|  (insert start after existing end, as a leaf)
-	 *            '--' no nodes falling in this range
-	 * b4.          >|_ _   !  (insert start before existing start)
-	 *
-	 * Case a3. resolves to b3.:
-	 * - if the inserted start element is the leftmost, because the '0'
-	 *   element in the tree serves as end element
-	 * - otherwise, if an existing end is found immediately to the left. If
-	 *   there are existing nodes in between, we need to further descend the
-	 *   tree before we can conclude the new start isn't causing an overlap
-	 *
-	 * or to b4., which, preceded by a3., means we already traversed one or
-	 * more existing intervals entirely, from the right.
-	 *
-	 * For a new, rightmost pair of elements, we'll hit cases b3. and b2.,
-	 * in that order.
-	 *
-	 * The flag is also cleared in two special cases:
-	 *
-	 * b5. |__ _ _!|<_ _ _   (insert start right before existing end)
-	 * b6. |__ _ >|!__ _ _   (insert end right after existing start)
-	 *
-	 * which always happen as last step and imply that no further
-	 * overlapping is possible.
-	 *
-	 * Another special case comes from the fact that start elements matching
-	 * an already existing start element are allowed: insertion is not
-	 * performed but we return -EEXIST in that case, and the error will be
-	 * cleared by the caller if NLM_F_EXCL is not present in the request.
-	 * This way, request for insertion of an exact overlap isn't reported as
-	 * error to userspace if not desired.
-	 *
-	 * However, if the existing start matches a pre-existing start, but the
-	 * end element doesn't match the corresponding pre-existing end element,
-	 * we need to report a partial overlap. This is a local condition that
-	 * can be noticed without need for a tracking flag, by checking for a
-	 * local duplicated end for a corresponding start, from left and right,
-	 * separately.
+	/* Descend the tree to search for an existing element greater than the
+	 * key value to insert that is greater than the new element. This is the
+	 * first element to walk the ordered elements to find possible overlap.
 	 */
-
 	parent = NULL;
 	p = &priv->root.rb_node;
 	while (*p != NULL) {
 		parent = *p;
 		rbe = rb_entry(parent, struct nft_rbtree_elem, node);
-		d = memcmp(nft_set_ext_key(&rbe->ext),
-			   nft_set_ext_key(&new->ext),
-			   set->klen);
+		d = nft_rbtree_cmp(set, rbe, new);
+
 		if (d < 0) {
 			p = &parent->rb_left;
-
-			if (nft_rbtree_interval_start(new)) {
-				if (nft_rbtree_interval_end(rbe) &&
-				    nft_set_elem_active(&rbe->ext, genmask) &&
-				    !nft_set_elem_expired(&rbe->ext) && !*p)
-					overlap = false;
-			} else {
-				if (dup_end_left && !*p)
-					return -ENOTEMPTY;
-
-				overlap = nft_rbtree_interval_end(rbe) &&
-					  nft_set_elem_active(&rbe->ext,
-							      genmask) &&
-					  !nft_set_elem_expired(&rbe->ext);
-
-				if (overlap) {
-					dup_end_right = true;
-					continue;
-				}
-			}
 		} else if (d > 0) {
-			p = &parent->rb_right;
+			if (!first ||
+			    nft_rbtree_update_first(set, rbe, first))
+				first = &rbe->node;
 
-			if (nft_rbtree_interval_end(new)) {
-				if (dup_end_right && !*p)
-					return -ENOTEMPTY;
-
-				overlap = nft_rbtree_interval_end(rbe) &&
-					  nft_set_elem_active(&rbe->ext,
-							      genmask) &&
-					  !nft_set_elem_expired(&rbe->ext);
-
-				if (overlap) {
-					dup_end_left = true;
-					continue;
-				}
-			} else if (nft_set_elem_active(&rbe->ext, genmask) &&
-				   !nft_set_elem_expired(&rbe->ext)) {
-				overlap = nft_rbtree_interval_end(rbe);
-			}
+			p = &parent->rb_right;
 		} else {
-			if (nft_rbtree_interval_end(rbe) &&
-			    nft_rbtree_interval_start(new)) {
+			if (nft_rbtree_interval_end(rbe))
 				p = &parent->rb_left;
-
-				if (nft_set_elem_active(&rbe->ext, genmask) &&
-				    !nft_set_elem_expired(&rbe->ext))
-					overlap = false;
-			} else if (nft_rbtree_interval_start(rbe) &&
-				   nft_rbtree_interval_end(new)) {
+			else
 				p = &parent->rb_right;
+		}
+	}
 
-				if (nft_set_elem_active(&rbe->ext, genmask) &&
-				    !nft_set_elem_expired(&rbe->ext))
-					overlap = false;
-			} else if (nft_set_elem_active(&rbe->ext, genmask) &&
-				   !nft_set_elem_expired(&rbe->ext)) {
-				*ext = &rbe->ext;
-				return -EEXIST;
-			} else {
-				p = &parent->rb_left;
+	if (!first)
+		first = rb_first(&priv->root);
+
+	/* Detect overlap by going through the list of valid tree nodes.
+	 * Values stored in the tree are in reversed order, starting from
+	 * highest to lowest value.
+	 */
+	for (node = first; node != NULL; node = next) {
+		next = rb_next(node);
+
+		rbe = rb_entry(node, struct nft_rbtree_elem, node);
+
+		if (!nft_set_elem_active(&rbe->ext, genmask))
+			continue;
+
+		/* perform garbage collection to avoid bogus overlap reports
+		 * but skip new elements in this transaction.
+		 */
+		if (__nft_set_elem_expired(&rbe->ext, tstamp) &&
+		    nft_set_elem_active(&rbe->ext, cur_genmask)) {
+			const struct nft_rbtree_elem *removed_end;
+
+			removed_end = nft_rbtree_gc_elem(set, priv, rbe);
+			if (IS_ERR(removed_end))
+				return PTR_ERR(removed_end);
+
+			if (removed_end == rbe_le || removed_end == rbe_ge)
+				return -EAGAIN;
+
+			continue;
+		}
+
+		d = nft_rbtree_cmp(set, rbe, new);
+		if (d == 0) {
+			/* Matching end element: no need to look for an
+			 * overlapping greater or equal element.
+			 */
+			if (nft_rbtree_interval_end(rbe)) {
+				rbe_le = rbe;
+				break;
+			}
+
+			/* first element that is greater or equal to key value. */
+			if (!rbe_ge) {
+				rbe_ge = rbe;
+				continue;
+			}
+
+			/* this is a closer more or equal element, update it. */
+			if (nft_rbtree_cmp(set, rbe_ge, new) != 0) {
+				rbe_ge = rbe;
+				continue;
+			}
+
+			/* element is equal to key value, make sure flags are
+			 * the same, an existing more or equal start element
+			 * must not be replaced by more or equal end element.
+			 */
+			if ((nft_rbtree_interval_start(new) &&
+			     nft_rbtree_interval_start(rbe_ge)) ||
+			    (nft_rbtree_interval_end(new) &&
+			     nft_rbtree_interval_end(rbe_ge))) {
+				rbe_ge = rbe;
+				continue;
 			}
+		} else if (d > 0) {
+			/* annotate element greater than the new element. */
+			rbe_ge = rbe;
+			continue;
+		} else if (d < 0) {
+			/* annotate element less than the new element. */
+			rbe_le = rbe;
+			break;
 		}
+	}
 
-		dup_end_left = dup_end_right = false;
+	/* - new start element matching existing start element: full overlap
+	 *   reported as -EEXIST, cleared by caller if NLM_F_EXCL is not given.
+	 */
+	if (rbe_ge && !nft_rbtree_cmp(set, new, rbe_ge) &&
+	    nft_rbtree_interval_start(rbe_ge) == nft_rbtree_interval_start(new)) {
+		*ext = &rbe_ge->ext;
+		return -EEXIST;
+	}
+
+	/* - new end element matching existing end element: full overlap
+	 *   reported as -EEXIST, cleared by caller if NLM_F_EXCL is not given.
+	 */
+	if (rbe_le && !nft_rbtree_cmp(set, new, rbe_le) &&
+	    nft_rbtree_interval_end(rbe_le) == nft_rbtree_interval_end(new)) {
+		*ext = &rbe_le->ext;
+		return -EEXIST;
 	}
 
-	if (overlap)
+	/* - new start element with existing closest, less or equal key value
+	 *   being a start element: partial overlap, reported as -ENOTEMPTY.
+	 *   Anonymous sets allow for two consecutive start element since they
+	 *   are constant, skip them to avoid bogus overlap reports.
+	 */
+	if (!nft_set_is_anonymous(set) && rbe_le &&
+	    nft_rbtree_interval_start(rbe_le) && nft_rbtree_interval_start(new))
+		return -ENOTEMPTY;
+
+	/* - new end element with existing closest, less or equal key value
+	 *   being a end element: partial overlap, reported as -ENOTEMPTY.
+	 */
+	if (rbe_le &&
+	    nft_rbtree_interval_end(rbe_le) && nft_rbtree_interval_end(new))
 		return -ENOTEMPTY;
 
+	/* - new end element with existing closest, greater or equal key value
+	 *   being an end element: partial overlap, reported as -ENOTEMPTY
+	 */
+	if (rbe_ge &&
+	    nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
+		return -ENOTEMPTY;
+
+	/* Accepted element: pick insertion point depending on key value */
+	parent = NULL;
+	p = &priv->root.rb_node;
+	while (*p != NULL) {
+		parent = *p;
+		rbe = rb_entry(parent, struct nft_rbtree_elem, node);
+		d = nft_rbtree_cmp(set, rbe, new);
+
+		if (d < 0)
+			p = &parent->rb_left;
+		else if (d > 0)
+			p = &parent->rb_right;
+		else if (nft_rbtree_interval_end(rbe))
+			p = &parent->rb_left;
+		else
+			p = &parent->rb_right;
+	}
+
 	rb_link_node_rcu(&new->node, parent, p);
 	rb_insert_color(&new->node, &priv->root);
 	return 0;
@@ -372,11 +492,18 @@
 	struct nft_rbtree_elem *rbe = elem->priv;
 	int err;
 
-	write_lock_bh(&priv->lock);
-	write_seqcount_begin(&priv->count);
-	err = __nft_rbtree_insert(net, set, rbe, ext);
-	write_seqcount_end(&priv->count);
-	write_unlock_bh(&priv->lock);
+	do {
+		if (fatal_signal_pending(current))
+			return -EINTR;
+
+		cond_resched();
+
+		write_lock_bh(&priv->lock);
+		write_seqcount_begin(&priv->count);
+		err = __nft_rbtree_insert(net, set, rbe, ext);
+		write_seqcount_end(&priv->count);
+		write_unlock_bh(&priv->lock);
+	} while (err == -EAGAIN);
 
 	return err;
 }
@@ -401,8 +528,7 @@
 {
 	struct nft_rbtree_elem *rbe = elem->priv;
 
-	nft_set_elem_change_active(net, set, &rbe->ext);
-	nft_set_elem_clear_busy(&rbe->ext);
+	nft_clear(net, &rbe->ext);
 }
 
 static bool nft_rbtree_flush(const struct net *net,
@@ -410,12 +536,9 @@
 {
 	struct nft_rbtree_elem *rbe = priv;
 
-	if (!nft_set_elem_mark_busy(&rbe->ext) ||
-	    !nft_is_active(net, &rbe->ext)) {
-		nft_set_elem_change_active(net, set, &rbe->ext);
-		return true;
-	}
-	return false;
+	nft_set_elem_change_active(net, set, &rbe->ext);
+
+	return true;
 }
 
 static void *nft_rbtree_deactivate(const struct net *net,
@@ -426,6 +549,7 @@
 	const struct rb_node *parent = priv->root.rb_node;
 	struct nft_rbtree_elem *rbe, *this = elem->priv;
 	u8 genmask = nft_genmask_next(net);
+	u64 tstamp = nft_net_tstamp(net);
 	int d;
 
 	while (parent != NULL) {
@@ -446,6 +570,8 @@
 				   nft_rbtree_interval_end(this)) {
 				parent = parent->rb_right;
 				continue;
+			} else if (__nft_set_elem_expired(&rbe->ext, tstamp)) {
+				break;
 			} else if (!nft_set_elem_active(&rbe->ext, genmask)) {
 				parent = parent->rb_left;
 				continue;
@@ -472,10 +598,6 @@
 
 		if (iter->count < iter->skip)
 			goto cont;
-		if (nft_set_elem_expired(&rbe->ext))
-			goto cont;
-		if (!nft_set_elem_active(&rbe->ext, iter->genmask))
-			goto cont;
 
 		elem.priv = rbe;
 
@@ -492,64 +614,83 @@
 
 static void nft_rbtree_gc(struct work_struct *work)
 {
-	struct nft_rbtree_elem *rbe, *rbe_end = NULL, *rbe_prev = NULL;
-	struct nft_set_gc_batch *gcb = NULL;
+	struct nft_rbtree_elem *rbe, *rbe_end = NULL;
+	struct nftables_pernet *nft_net;
 	struct nft_rbtree *priv;
+	struct nft_trans_gc *gc;
 	struct rb_node *node;
 	struct nft_set *set;
+	unsigned int gc_seq;
+	struct net *net;
 
 	priv = container_of(work, struct nft_rbtree, gc_work.work);
 	set  = nft_set_container_of(priv);
+	net  = read_pnet(&set->net);
+	nft_net = nft_pernet(net);
+	gc_seq  = READ_ONCE(nft_net->gc_seq);
+
+	if (nft_set_gc_is_pending(set))
+		goto done;
+
+	gc = nft_trans_gc_alloc(set, gc_seq, GFP_KERNEL);
+	if (!gc)
+		goto done;
 
-	write_lock_bh(&priv->lock);
-	write_seqcount_begin(&priv->count);
+	read_lock_bh(&priv->lock);
 	for (node = rb_first(&priv->root); node != NULL; node = rb_next(node)) {
+
+		/* Ruleset has been updated, try later. */
+		if (READ_ONCE(nft_net->gc_seq) != gc_seq) {
+			nft_trans_gc_destroy(gc);
+			gc = NULL;
+			goto try_later;
+		}
+
 		rbe = rb_entry(node, struct nft_rbtree_elem, node);
 
+		if (nft_set_elem_is_dead(&rbe->ext))
+			goto dead_elem;
+
+		/* elements are reversed in the rbtree for historical reasons,
+		 * from highest to lowest value, that is why end element is
+		 * always visited before the start element.
+		 */
 		if (nft_rbtree_interval_end(rbe)) {
 			rbe_end = rbe;
 			continue;
 		}
 		if (!nft_set_elem_expired(&rbe->ext))
 			continue;
-		if (nft_set_elem_mark_busy(&rbe->ext))
+
+		nft_set_elem_dead(&rbe->ext);
+
+		if (!rbe_end)
 			continue;
 
-		if (rbe_prev) {
-			rb_erase(&rbe_prev->node, &priv->root);
-			rbe_prev = NULL;
-		}
-		gcb = nft_set_gc_batch_check(set, gcb, GFP_ATOMIC);
-		if (!gcb)
-			break;
+		nft_set_elem_dead(&rbe_end->ext);
 
-		atomic_dec(&set->nelems);
-		nft_set_gc_batch_add(gcb, rbe);
-		rbe_prev = rbe;
-
-		if (rbe_end) {
-			atomic_dec(&set->nelems);
-			nft_set_gc_batch_add(gcb, rbe_end);
-			rb_erase(&rbe_end->node, &priv->root);
-			rbe_end = NULL;
-		}
-		node = rb_next(node);
-		if (!node)
-			break;
-	}
-	if (rbe_prev)
-		rb_erase(&rbe_prev->node, &priv->root);
-	write_seqcount_end(&priv->count);
-	write_unlock_bh(&priv->lock);
+		gc = nft_trans_gc_queue_async(gc, gc_seq, GFP_ATOMIC);
+		if (!gc)
+			goto try_later;
 
-	rbe = nft_set_catchall_gc(set);
-	if (rbe) {
-		gcb = nft_set_gc_batch_check(set, gcb, GFP_ATOMIC);
-		if (gcb)
-			nft_set_gc_batch_add(gcb, rbe);
+		nft_trans_gc_elem_add(gc, rbe_end);
+		rbe_end = NULL;
+dead_elem:
+		gc = nft_trans_gc_queue_async(gc, gc_seq, GFP_ATOMIC);
+		if (!gc)
+			goto try_later;
+
+		nft_trans_gc_elem_add(gc, rbe);
 	}
-	nft_set_gc_batch_complete(gcb);
 
+	gc = nft_trans_gc_catchall_async(gc, gc_seq);
+
+try_later:
+	read_unlock_bh(&priv->lock);
+
+	if (gc)
+		nft_trans_gc_queue_async_done(gc);
+done:
 	queue_delayed_work(system_power_efficient_wq, &priv->gc_work,
 			   nft_set_gc_interval(set));
 }
@@ -578,7 +719,8 @@
 	return 0;
 }
 
-static void nft_rbtree_destroy(const struct nft_set *set)
+static void nft_rbtree_destroy(const struct nft_ctx *ctx,
+			       const struct nft_set *set)
 {
 	struct nft_rbtree *priv = nft_set_priv(set);
 	struct nft_rbtree_elem *rbe;
@@ -589,7 +731,7 @@
 	while ((node = priv->root.rb_node) != NULL) {
 		rb_erase(node, &priv->root);
 		rbe = rb_entry(node, struct nft_rbtree_elem, node);
-		nft_set_elem_destroy(set, rbe, true);
+		nf_tables_set_elem_destroy(ctx, set, rbe);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_socket.c
@@ -36,12 +36,11 @@
 
 #ifdef CONFIG_SOCK_CGROUP_DATA
 static noinline bool
-nft_sock_get_eval_cgroupv2(u32 *dest, const struct nft_pktinfo *pkt, u32 level)
+nft_sock_get_eval_cgroupv2(u32 *dest, struct sock *sk, const struct nft_pktinfo *pkt, u32 level)
 {
-	struct sock *sk = skb_to_full_sk(pkt->skb);
 	struct cgroup *cgrp;
 
-	if (!sk || !sk_fullsock(sk) || !net_eq(nft_net(pkt), sock_net(sk)))
+	if (!sk_fullsock(sk))
 		return false;
 
 	cgrp = sock_cgroup_ptr(&sk->sk_cgrp_data);
@@ -54,6 +53,32 @@
 }
 #endif
 
+static struct sock *nft_socket_do_lookup(const struct nft_pktinfo *pkt)
+{
+	const struct net_device *indev = nft_in(pkt);
+	const struct sk_buff *skb = pkt->skb;
+	struct sock *sk = NULL;
+
+	if (!indev)
+		return NULL;
+
+	switch (nft_pf(pkt)) {
+	case NFPROTO_IPV4:
+		sk = nf_sk_lookup_slow_v4(nft_net(pkt), skb, indev);
+		break;
+#if IS_ENABLED(CONFIG_NF_TABLES_IPV6)
+	case NFPROTO_IPV6:
+		sk = nf_sk_lookup_slow_v6(nft_net(pkt), skb, indev);
+		break;
+#endif
+	default:
+		WARN_ON_ONCE(1);
+		break;
+	}
+
+	return sk;
+}
+
 static void nft_socket_eval(const struct nft_expr *expr,
 			    struct nft_regs *regs,
 			    const struct nft_pktinfo *pkt)
@@ -67,20 +92,7 @@
 		sk = NULL;
 
 	if (!sk)
-		switch(nft_pf(pkt)) {
-		case NFPROTO_IPV4:
-			sk = nf_sk_lookup_slow_v4(nft_net(pkt), skb, nft_in(pkt));
-			break;
-#if IS_ENABLED(CONFIG_NF_TABLES_IPV6)
-		case NFPROTO_IPV6:
-			sk = nf_sk_lookup_slow_v6(nft_net(pkt), skb, nft_in(pkt));
-			break;
-#endif
-		default:
-			WARN_ON_ONCE(1);
-			regs->verdict.code = NFT_BREAK;
-			return;
-		}
+		sk = nft_socket_do_lookup(pkt);
 
 	if (!sk) {
 		regs->verdict.code = NFT_BREAK;
@@ -96,21 +108,21 @@
 			*dest = sk->sk_mark;
 		} else {
 			regs->verdict.code = NFT_BREAK;
-			return;
+			goto out_put_sk;
 		}
 		break;
 	case NFT_SOCKET_WILDCARD:
 		if (!sk_fullsock(sk)) {
 			regs->verdict.code = NFT_BREAK;
-			return;
+			goto out_put_sk;
 		}
 		nft_socket_wildcard(pkt, regs, sk, dest);
 		break;
 #ifdef CONFIG_SOCK_CGROUP_DATA
 	case NFT_SOCKET_CGROUPV2:
-		if (!nft_sock_get_eval_cgroupv2(dest, pkt, priv->level)) {
+		if (!nft_sock_get_eval_cgroupv2(dest, sk, pkt, priv->level)) {
 			regs->verdict.code = NFT_BREAK;
-			return;
+			goto out_put_sk;
 		}
 		break;
 #endif
@@ -119,6 +131,7 @@
 		regs->verdict.code = NFT_BREAK;
 	}
 
+out_put_sk:
 	if (sk != skb->sk)
 		sock_gen_put(sk);
 }
@@ -150,7 +163,7 @@
 		return -EOPNOTSUPP;
 	}
 
-	priv->key = ntohl(nla_get_u32(tb[NFTA_SOCKET_KEY]));
+	priv->key = ntohl(nla_get_be32(tb[NFTA_SOCKET_KEY]));
 	switch(priv->key) {
 	case NFT_SOCKET_TRANSPARENT:
 	case NFT_SOCKET_WILDCARD:
@@ -166,7 +179,7 @@
 		if (!tb[NFTA_SOCKET_LEVEL])
 			return -EINVAL;
 
-		level = ntohl(nla_get_u32(tb[NFTA_SOCKET_LEVEL]));
+		level = ntohl(nla_get_be32(tb[NFTA_SOCKET_LEVEL]));
 		if (level > 255)
 			return -EOPNOTSUPP;
 
@@ -188,16 +201,31 @@
 {
 	const struct nft_socket *priv = nft_expr_priv(expr);
 
-	if (nla_put_u32(skb, NFTA_SOCKET_KEY, htonl(priv->key)))
+	if (nla_put_be32(skb, NFTA_SOCKET_KEY, htonl(priv->key)))
 		return -1;
 	if (nft_dump_register(skb, NFTA_SOCKET_DREG, priv->dreg))
 		return -1;
 	if (priv->key == NFT_SOCKET_CGROUPV2 &&
-	    nla_put_u32(skb, NFTA_SOCKET_LEVEL, htonl(priv->level)))
+	    nla_put_be32(skb, NFTA_SOCKET_LEVEL, htonl(priv->level)))
 		return -1;
 	return 0;
 }
 
+static int nft_socket_validate(const struct nft_ctx *ctx,
+			       const struct nft_expr *expr,
+			       const struct nft_data **data)
+{
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
+	return nft_chain_validate_hooks(ctx->chain,
+					(1 << NF_INET_PRE_ROUTING) |
+					(1 << NF_INET_LOCAL_IN) |
+					(1 << NF_INET_LOCAL_OUT));
+}
+
 static struct nft_expr_type nft_socket_type;
 static const struct nft_expr_ops nft_socket_ops = {
 	.type		= &nft_socket_type,
@@ -205,6 +233,7 @@
 	.eval		= nft_socket_eval,
 	.init		= nft_socket_init,
 	.dump		= nft_socket_dump,
+	.validate	= nft_socket_validate,
 };
 
 static struct nft_expr_type nft_socket_type __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_synproxy.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_synproxy.c
@@ -186,13 +186,14 @@
 		break;
 #endif
 	case NFPROTO_INET:
-	case NFPROTO_BRIDGE:
 		err = nf_synproxy_ipv4_init(snet, ctx->net);
 		if (err)
 			goto nf_ct_failure;
 		err = nf_synproxy_ipv6_init(snet, ctx->net);
-		if (err)
+		if (err) {
+			nf_synproxy_ipv4_fini(snet, ctx->net);
 			goto nf_ct_failure;
+		}
 		break;
 	}
 
@@ -217,7 +218,6 @@
 		break;
 #endif
 	case NFPROTO_INET:
-	case NFPROTO_BRIDGE:
 		nf_synproxy_ipv4_fini(snet, ctx->net);
 		nf_synproxy_ipv6_fini(snet, ctx->net);
 		break;
@@ -251,6 +251,11 @@
 				 const struct nft_expr *expr,
 				 const struct nft_data **data)
 {
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
 	return nft_chain_validate_hooks(ctx->chain, (1 << NF_INET_LOCAL_IN) |
 						    (1 << NF_INET_FORWARD));
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_tproxy.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_tproxy.c
@@ -52,11 +52,11 @@
 				   skb->dev, NF_TPROXY_LOOKUP_ESTABLISHED);
 
 	if (priv->sreg_addr)
-		taddr = regs->data[priv->sreg_addr];
+		taddr = nft_reg_load_be32(&regs->data[priv->sreg_addr]);
 	taddr = nf_tproxy_laddr4(skb, taddr, iph->daddr);
 
 	if (priv->sreg_port)
-		tport = nft_reg_load16(&regs->data[priv->sreg_port]);
+		tport = nft_reg_load_be16(&regs->data[priv->sreg_port]);
 	if (!tport)
 		tport = hp->dest;
 
@@ -124,7 +124,7 @@
 	taddr = *nf_tproxy_laddr6(skb, &taddr, &iph->daddr);
 
 	if (priv->sreg_port)
-		tport = nft_reg_load16(&regs->data[priv->sreg_port]);
+		tport = nft_reg_load_be16(&regs->data[priv->sreg_port]);
 	if (!tport)
 		tport = hp->dest;
 
@@ -312,6 +312,18 @@
 	return 0;
 }
 
+static int nft_tproxy_validate(const struct nft_ctx *ctx,
+			       const struct nft_expr *expr,
+			       const struct nft_data **data)
+{
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
+	return nft_chain_validate_hooks(ctx->chain, 1 << NF_INET_PRE_ROUTING);
+}
+
 static struct nft_expr_type nft_tproxy_type;
 static const struct nft_expr_ops nft_tproxy_ops = {
 	.type		= &nft_tproxy_type,
@@ -320,6 +332,7 @@
 	.init		= nft_tproxy_init,
 	.destroy	= nft_tproxy_destroy,
 	.dump		= nft_tproxy_dump,
+	.validate	= nft_tproxy_validate,
 };
 
 static struct nft_expr_type nft_tproxy_type __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_tunnel.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_tunnel.c
@@ -133,6 +133,7 @@
 
 static struct nft_expr_type nft_tunnel_type __read_mostly = {
 	.name		= "tunnel",
+	.family		= NFPROTO_NETDEV,
 	.ops		= &nft_tunnel_get_ops,
 	.policy		= nft_tunnel_policy,
 	.maxattr	= NFTA_TUNNEL_MAX,
@@ -304,13 +305,13 @@
 static const struct nla_policy nft_tunnel_opts_geneve_policy[NFTA_TUNNEL_KEY_GENEVE_MAX + 1] = {
 	[NFTA_TUNNEL_KEY_GENEVE_CLASS]	= { .type = NLA_U16 },
 	[NFTA_TUNNEL_KEY_GENEVE_TYPE]	= { .type = NLA_U8 },
-	[NFTA_TUNNEL_KEY_GENEVE_DATA]	= { .type = NLA_BINARY, .len = 128 },
+	[NFTA_TUNNEL_KEY_GENEVE_DATA]	= { .type = NLA_BINARY, .len = 127 },
 };
 
 static int nft_tunnel_obj_geneve_init(const struct nlattr *attr,
 				      struct nft_tunnel_opts *opts)
 {
-	struct geneve_opt *opt = (struct geneve_opt *)opts->u.data + opts->len;
+	struct geneve_opt *opt = (struct geneve_opt *)(opts->u.data + opts->len);
 	struct nlattr *tb[NFTA_TUNNEL_KEY_GENEVE_MAX + 1];
 	int err, data_len;
 
@@ -591,7 +592,7 @@
 		if (!inner)
 			goto failure;
 		while (opts->len > offset) {
-			opt = (struct geneve_opt *)opts->u.data + offset;
+			opt = (struct geneve_opt *)(opts->u.data + offset);
 			if (nla_put_be16(skb, NFTA_TUNNEL_KEY_GENEVE_CLASS,
 					 opt->opt_class) ||
 			    nla_put_u8(skb, NFTA_TUNNEL_KEY_GENEVE_TYPE,
@@ -683,6 +684,7 @@
 
 static struct nft_object_type nft_tunnel_obj_type __read_mostly = {
 	.type		= NFT_OBJECT_TUNNEL,
+	.family		= NFPROTO_NETDEV,
 	.ops		= &nft_tunnel_obj_ops,
 	.maxattr	= NFTA_TUNNEL_KEY_MAX,
 	.policy		= nft_tunnel_key_policy,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/nft_xfrm.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/nft_xfrm.c
@@ -50,7 +50,7 @@
 		return -EOPNOTSUPP;
 	}
 
-	priv->key = ntohl(nla_get_u32(tb[NFTA_XFRM_KEY]));
+	priv->key = ntohl(nla_get_be32(tb[NFTA_XFRM_KEY]));
 	switch (priv->key) {
 	case NFT_XFRM_KEY_REQID:
 	case NFT_XFRM_KEY_SPI:
@@ -132,13 +132,13 @@
 		WARN_ON_ONCE(1);
 		break;
 	case NFT_XFRM_KEY_DADDR_IP4:
-		*dest = state->id.daddr.a4;
+		*dest = (__force __u32)state->id.daddr.a4;
 		return;
 	case NFT_XFRM_KEY_DADDR_IP6:
 		memcpy(dest, &state->id.daddr.in6, sizeof(struct in6_addr));
 		return;
 	case NFT_XFRM_KEY_SADDR_IP4:
-		*dest = state->props.saddr.a4;
+		*dest = (__force __u32)state->props.saddr.a4;
 		return;
 	case NFT_XFRM_KEY_SADDR_IP6:
 		memcpy(dest, &state->props.saddr.in6, sizeof(struct in6_addr));
@@ -147,7 +147,7 @@
 		*dest = state->props.reqid;
 		return;
 	case NFT_XFRM_KEY_SPI:
-		*dest = state->id.spi;
+		*dest = (__force __u32)state->id.spi;
 		return;
 	}
 
@@ -233,6 +233,11 @@
 	const struct nft_xfrm *priv = nft_expr_priv(expr);
 	unsigned int hooks;
 
+	if (ctx->family != NFPROTO_IPV4 &&
+	    ctx->family != NFPROTO_IPV6 &&
+	    ctx->family != NFPROTO_INET)
+		return -EOPNOTSUPP;
+
 	switch (priv->dir) {
 	case XFRM_POLICY_IN:
 		hooks = (1 << NF_INET_FORWARD) |
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/x_tables.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/x_tables.c
@@ -1268,7 +1268,7 @@
 
 	/* and once again: */
 	list_for_each_entry(t, &xt_net->tables[af], list)
-		if (strcmp(t->name, name) == 0)
+		if (strcmp(t->name, name) == 0 && owner == t->me)
 			return t;
 
 	module_put(owner);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_CHECKSUM.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_CHECKSUM.c
@@ -63,24 +63,37 @@
 	return 0;
 }
 
-static struct xt_target checksum_tg_reg __read_mostly = {
-	.name		= "CHECKSUM",
-	.family		= NFPROTO_UNSPEC,
-	.target		= checksum_tg,
-	.targetsize	= sizeof(struct xt_CHECKSUM_info),
-	.table		= "mangle",
-	.checkentry	= checksum_tg_check,
-	.me		= THIS_MODULE,
+static struct xt_target checksum_tg_reg[] __read_mostly = {
+	{
+		.name		= "CHECKSUM",
+		.family		= NFPROTO_IPV4,
+		.target		= checksum_tg,
+		.targetsize	= sizeof(struct xt_CHECKSUM_info),
+		.table		= "mangle",
+		.checkentry	= checksum_tg_check,
+		.me		= THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "CHECKSUM",
+		.family		= NFPROTO_IPV6,
+		.target		= checksum_tg,
+		.targetsize	= sizeof(struct xt_CHECKSUM_info),
+		.table		= "mangle",
+		.checkentry	= checksum_tg_check,
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static int __init checksum_tg_init(void)
 {
-	return xt_register_target(&checksum_tg_reg);
+	return xt_register_targets(checksum_tg_reg, ARRAY_SIZE(checksum_tg_reg));
 }
 
 static void __exit checksum_tg_exit(void)
 {
-	xt_unregister_target(&checksum_tg_reg);
+	xt_unregister_targets(checksum_tg_reg, ARRAY_SIZE(checksum_tg_reg));
 }
 
 module_init(checksum_tg_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_CLASSIFY.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_CLASSIFY.c
@@ -38,9 +38,9 @@
 	{
 		.name       = "CLASSIFY",
 		.revision   = 0,
-		.family     = NFPROTO_UNSPEC,
+		.family     = NFPROTO_IPV4,
 		.hooks      = (1 << NF_INET_LOCAL_OUT) | (1 << NF_INET_FORWARD) |
-		              (1 << NF_INET_POST_ROUTING),
+			      (1 << NF_INET_POST_ROUTING),
 		.target     = classify_tg,
 		.targetsize = sizeof(struct xt_classify_target_info),
 		.me         = THIS_MODULE,
@@ -54,6 +54,18 @@
 		.targetsize = sizeof(struct xt_classify_target_info),
 		.me         = THIS_MODULE,
 	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name       = "CLASSIFY",
+		.revision   = 0,
+		.family     = NFPROTO_IPV6,
+		.hooks      = (1 << NF_INET_LOCAL_OUT) | (1 << NF_INET_FORWARD) |
+			      (1 << NF_INET_POST_ROUTING),
+		.target     = classify_tg,
+		.targetsize = sizeof(struct xt_classify_target_info),
+		.me         = THIS_MODULE,
+	},
+#endif
 };
 
 static int __init classify_tg_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_CONNSECMARK.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_CONNSECMARK.c
@@ -114,25 +114,39 @@
 	nf_ct_netns_put(par->net, par->family);
 }
 
-static struct xt_target connsecmark_tg_reg __read_mostly = {
-	.name       = "CONNSECMARK",
-	.revision   = 0,
-	.family     = NFPROTO_UNSPEC,
-	.checkentry = connsecmark_tg_check,
-	.destroy    = connsecmark_tg_destroy,
-	.target     = connsecmark_tg,
-	.targetsize = sizeof(struct xt_connsecmark_target_info),
-	.me         = THIS_MODULE,
+static struct xt_target connsecmark_tg_reg[] __read_mostly = {
+	{
+		.name       = "CONNSECMARK",
+		.revision   = 0,
+		.family     = NFPROTO_IPV4,
+		.checkentry = connsecmark_tg_check,
+		.destroy    = connsecmark_tg_destroy,
+		.target     = connsecmark_tg,
+		.targetsize = sizeof(struct xt_connsecmark_target_info),
+		.me         = THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name       = "CONNSECMARK",
+		.revision   = 0,
+		.family     = NFPROTO_IPV6,
+		.checkentry = connsecmark_tg_check,
+		.destroy    = connsecmark_tg_destroy,
+		.target     = connsecmark_tg,
+		.targetsize = sizeof(struct xt_connsecmark_target_info),
+		.me         = THIS_MODULE,
+	},
+#endif
 };
 
 static int __init connsecmark_tg_init(void)
 {
-	return xt_register_target(&connsecmark_tg_reg);
+	return xt_register_targets(connsecmark_tg_reg, ARRAY_SIZE(connsecmark_tg_reg));
 }
 
 static void __exit connsecmark_tg_exit(void)
 {
-	xt_unregister_target(&connsecmark_tg_reg);
+	xt_unregister_targets(connsecmark_tg_reg, ARRAY_SIZE(connsecmark_tg_reg));
 }
 
 module_init(connsecmark_tg_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_CT.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_CT.c
@@ -24,7 +24,7 @@
 		return XT_CONTINUE;
 
 	if (ct) {
-		atomic_inc(&ct->ct_general.use);
+		refcount_inc(&ct->ct_general.use);
 		nf_ct_set(skb, ct, IP_CT_NEW);
 	} else {
 		nf_ct_set(skb, ct, IP_CT_UNTRACKED);
@@ -201,7 +201,6 @@
 			goto err4;
 	}
 	__set_bit(IPS_CONFIRMED_BIT, &ct->status);
-	nf_conntrack_get(&ct->ct_general);
 out:
 	info->ct = ct;
 	return 0;
@@ -301,10 +300,30 @@
 	xt_ct_tg_destroy(par, par->targinfo);
 }
 
+static unsigned int
+notrack_tg(struct sk_buff *skb, const struct xt_action_param *par)
+{
+	/* Previously seen (loopback)? Ignore. */
+	if (skb->_nfct != 0)
+		return XT_CONTINUE;
+
+	nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
+
+	return XT_CONTINUE;
+}
+
 static struct xt_target xt_ct_tg_reg[] __read_mostly = {
 	{
+		.name		= "NOTRACK",
+		.revision	= 0,
+		.family		= NFPROTO_IPV4,
+		.target		= notrack_tg,
+		.table		= "raw",
+		.me		= THIS_MODULE,
+	},
+	{
 		.name		= "CT",
-		.family		= NFPROTO_UNSPEC,
+		.family		= NFPROTO_IPV4,
 		.targetsize	= sizeof(struct xt_ct_target_info),
 		.usersize	= offsetof(struct xt_ct_target_info, ct),
 		.checkentry	= xt_ct_tg_check_v0,
@@ -315,7 +334,7 @@
 	},
 	{
 		.name		= "CT",
-		.family		= NFPROTO_UNSPEC,
+		.family		= NFPROTO_IPV4,
 		.revision	= 1,
 		.targetsize	= sizeof(struct xt_ct_target_info_v1),
 		.usersize	= offsetof(struct xt_ct_target_info, ct),
@@ -327,7 +346,7 @@
 	},
 	{
 		.name		= "CT",
-		.family		= NFPROTO_UNSPEC,
+		.family		= NFPROTO_IPV4,
 		.revision	= 2,
 		.targetsize	= sizeof(struct xt_ct_target_info_v1),
 		.usersize	= offsetof(struct xt_ct_target_info, ct),
@@ -337,49 +356,61 @@
 		.table		= "raw",
 		.me		= THIS_MODULE,
 	},
-};
-
-static unsigned int
-notrack_tg(struct sk_buff *skb, const struct xt_action_param *par)
-{
-	/* Previously seen (loopback)? Ignore. */
-	if (skb->_nfct != 0)
-		return XT_CONTINUE;
-
-	nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
-
-	return XT_CONTINUE;
-}
-
-static struct xt_target notrack_tg_reg __read_mostly = {
-	.name		= "NOTRACK",
-	.revision	= 0,
-	.family		= NFPROTO_UNSPEC,
-	.target		= notrack_tg,
-	.table		= "raw",
-	.me		= THIS_MODULE,
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "NOTRACK",
+		.revision	= 0,
+		.family		= NFPROTO_IPV6,
+		.target		= notrack_tg,
+		.table		= "raw",
+		.me		= THIS_MODULE,
+	},
+	{
+		.name		= "CT",
+		.family		= NFPROTO_IPV6,
+		.targetsize	= sizeof(struct xt_ct_target_info),
+		.usersize	= offsetof(struct xt_ct_target_info, ct),
+		.checkentry	= xt_ct_tg_check_v0,
+		.destroy	= xt_ct_tg_destroy_v0,
+		.target		= xt_ct_target_v0,
+		.table		= "raw",
+		.me		= THIS_MODULE,
+	},
+	{
+		.name		= "CT",
+		.family		= NFPROTO_IPV6,
+		.revision	= 1,
+		.targetsize	= sizeof(struct xt_ct_target_info_v1),
+		.usersize	= offsetof(struct xt_ct_target_info, ct),
+		.checkentry	= xt_ct_tg_check_v1,
+		.destroy	= xt_ct_tg_destroy_v1,
+		.target		= xt_ct_target_v1,
+		.table		= "raw",
+		.me		= THIS_MODULE,
+	},
+	{
+		.name		= "CT",
+		.family		= NFPROTO_IPV6,
+		.revision	= 2,
+		.targetsize	= sizeof(struct xt_ct_target_info_v1),
+		.usersize	= offsetof(struct xt_ct_target_info, ct),
+		.checkentry	= xt_ct_tg_check_v2,
+		.destroy	= xt_ct_tg_destroy_v1,
+		.target		= xt_ct_target_v1,
+		.table		= "raw",
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static int __init xt_ct_tg_init(void)
 {
-	int ret;
-
-	ret = xt_register_target(&notrack_tg_reg);
-	if (ret < 0)
-		return ret;
-
-	ret = xt_register_targets(xt_ct_tg_reg, ARRAY_SIZE(xt_ct_tg_reg));
-	if (ret < 0) {
-		xt_unregister_target(&notrack_tg_reg);
-		return ret;
-	}
-	return 0;
+	return xt_register_targets(xt_ct_tg_reg, ARRAY_SIZE(xt_ct_tg_reg));
 }
 
 static void __exit xt_ct_tg_exit(void)
 {
 	xt_unregister_targets(xt_ct_tg_reg, ARRAY_SIZE(xt_ct_tg_reg));
-	xt_unregister_target(&notrack_tg_reg);
 }
 
 module_init(xt_ct_tg_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_IDLETIMER.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_IDLETIMER.c
@@ -458,28 +458,49 @@
 
 static struct xt_target idletimer_tg[] __read_mostly = {
 	{
-	.name		= "IDLETIMER",
-	.family		= NFPROTO_UNSPEC,
-	.target		= idletimer_tg_target,
-	.targetsize     = sizeof(struct idletimer_tg_info),
-	.usersize	= offsetof(struct idletimer_tg_info, timer),
-	.checkentry	= idletimer_tg_checkentry,
-	.destroy        = idletimer_tg_destroy,
-	.me		= THIS_MODULE,
+		.name		= "IDLETIMER",
+		.family		= NFPROTO_IPV4,
+		.target		= idletimer_tg_target,
+		.targetsize     = sizeof(struct idletimer_tg_info),
+		.usersize	= offsetof(struct idletimer_tg_info, timer),
+		.checkentry	= idletimer_tg_checkentry,
+		.destroy        = idletimer_tg_destroy,
+		.me		= THIS_MODULE,
 	},
 	{
-	.name		= "IDLETIMER",
-	.family		= NFPROTO_UNSPEC,
-	.revision	= 1,
-	.target		= idletimer_tg_target_v1,
-	.targetsize     = sizeof(struct idletimer_tg_info_v1),
-	.usersize	= offsetof(struct idletimer_tg_info_v1, timer),
-	.checkentry	= idletimer_tg_checkentry_v1,
-	.destroy        = idletimer_tg_destroy_v1,
-	.me		= THIS_MODULE,
+		.name		= "IDLETIMER",
+		.family		= NFPROTO_IPV4,
+		.revision	= 1,
+		.target		= idletimer_tg_target_v1,
+		.targetsize     = sizeof(struct idletimer_tg_info_v1),
+		.usersize	= offsetof(struct idletimer_tg_info_v1, timer),
+		.checkentry	= idletimer_tg_checkentry_v1,
+		.destroy        = idletimer_tg_destroy_v1,
+		.me		= THIS_MODULE,
 	},
-
-
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "IDLETIMER",
+		.family		= NFPROTO_IPV6,
+		.target		= idletimer_tg_target,
+		.targetsize     = sizeof(struct idletimer_tg_info),
+		.usersize	= offsetof(struct idletimer_tg_info, timer),
+		.checkentry	= idletimer_tg_checkentry,
+		.destroy        = idletimer_tg_destroy,
+		.me		= THIS_MODULE,
+	},
+	{
+		.name		= "IDLETIMER",
+		.family		= NFPROTO_IPV6,
+		.revision	= 1,
+		.target		= idletimer_tg_target_v1,
+		.targetsize     = sizeof(struct idletimer_tg_info_v1),
+		.usersize	= offsetof(struct idletimer_tg_info_v1, timer),
+		.checkentry	= idletimer_tg_checkentry_v1,
+		.destroy        = idletimer_tg_destroy_v1,
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static struct class *idletimer_tg_class;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_LED.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_LED.c
@@ -97,7 +97,9 @@
 	struct xt_led_info_internal *ledinternal;
 	int err;
 
-	if (ledinfo->id[0] == '\0')
+	/* Bail out if empty string or not a string at all. */
+	if (ledinfo->id[0] == '\0' ||
+	    !memchr(ledinfo->id, '\0', sizeof(ledinfo->id)))
 		return -EINVAL;
 
 	mutex_lock(&xt_led_mutex);
@@ -176,26 +178,41 @@
 	kfree(ledinternal);
 }
 
-static struct xt_target led_tg_reg __read_mostly = {
-	.name		= "LED",
-	.revision	= 0,
-	.family		= NFPROTO_UNSPEC,
-	.target		= led_tg,
-	.targetsize	= sizeof(struct xt_led_info),
-	.usersize	= offsetof(struct xt_led_info, internal_data),
-	.checkentry	= led_tg_check,
-	.destroy	= led_tg_destroy,
-	.me		= THIS_MODULE,
+static struct xt_target led_tg_reg[] __read_mostly = {
+	{
+		.name		= "LED",
+		.revision	= 0,
+		.family		= NFPROTO_IPV4,
+		.target		= led_tg,
+		.targetsize	= sizeof(struct xt_led_info),
+		.usersize	= offsetof(struct xt_led_info, internal_data),
+		.checkentry	= led_tg_check,
+		.destroy	= led_tg_destroy,
+		.me		= THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "LED",
+		.revision	= 0,
+		.family		= NFPROTO_IPV6,
+		.target		= led_tg,
+		.targetsize	= sizeof(struct xt_led_info),
+		.usersize	= offsetof(struct xt_led_info, internal_data),
+		.checkentry	= led_tg_check,
+		.destroy	= led_tg_destroy,
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static int __init led_tg_init(void)
 {
-	return xt_register_target(&led_tg_reg);
+	return xt_register_targets(led_tg_reg, ARRAY_SIZE(led_tg_reg));
 }
 
 static void __exit led_tg_exit(void)
 {
-	xt_unregister_target(&led_tg_reg);
+	xt_unregister_targets(led_tg_reg, ARRAY_SIZE(led_tg_reg));
 }
 
 module_init(led_tg_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_NFLOG.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_NFLOG.c
@@ -64,25 +64,39 @@
 	nf_logger_put(par->family, NF_LOG_TYPE_ULOG);
 }
 
-static struct xt_target nflog_tg_reg __read_mostly = {
-	.name       = "NFLOG",
-	.revision   = 0,
-	.family     = NFPROTO_UNSPEC,
-	.checkentry = nflog_tg_check,
-	.destroy    = nflog_tg_destroy,
-	.target     = nflog_tg,
-	.targetsize = sizeof(struct xt_nflog_info),
-	.me         = THIS_MODULE,
+static struct xt_target nflog_tg_reg[] __read_mostly = {
+	{
+		.name       = "NFLOG",
+		.revision   = 0,
+		.family     = NFPROTO_IPV4,
+		.checkentry = nflog_tg_check,
+		.destroy    = nflog_tg_destroy,
+		.target     = nflog_tg,
+		.targetsize = sizeof(struct xt_nflog_info),
+		.me         = THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name       = "NFLOG",
+		.revision   = 0,
+		.family     = NFPROTO_IPV6,
+		.checkentry = nflog_tg_check,
+		.destroy    = nflog_tg_destroy,
+		.target     = nflog_tg,
+		.targetsize = sizeof(struct xt_nflog_info),
+		.me         = THIS_MODULE,
+	},
+#endif
 };
 
 static int __init nflog_tg_init(void)
 {
-	return xt_register_target(&nflog_tg_reg);
+	return xt_register_targets(nflog_tg_reg, ARRAY_SIZE(nflog_tg_reg));
 }
 
 static void __exit nflog_tg_exit(void)
 {
-	xt_unregister_target(&nflog_tg_reg);
+	xt_unregister_targets(nflog_tg_reg, ARRAY_SIZE(nflog_tg_reg));
 }
 
 module_init(nflog_tg_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_RATEEST.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_RATEEST.c
@@ -178,16 +178,31 @@
 	xt_rateest_put(par->net, info->est);
 }
 
-static struct xt_target xt_rateest_tg_reg __read_mostly = {
-	.name       = "RATEEST",
-	.revision   = 0,
-	.family     = NFPROTO_UNSPEC,
-	.target     = xt_rateest_tg,
-	.checkentry = xt_rateest_tg_checkentry,
-	.destroy    = xt_rateest_tg_destroy,
-	.targetsize = sizeof(struct xt_rateest_target_info),
-	.usersize   = offsetof(struct xt_rateest_target_info, est),
-	.me         = THIS_MODULE,
+static struct xt_target xt_rateest_tg_reg[] __read_mostly = {
+	{
+		.name       = "RATEEST",
+		.revision   = 0,
+		.family     = NFPROTO_IPV4,
+		.target     = xt_rateest_tg,
+		.checkentry = xt_rateest_tg_checkentry,
+		.destroy    = xt_rateest_tg_destroy,
+		.targetsize = sizeof(struct xt_rateest_target_info),
+		.usersize   = offsetof(struct xt_rateest_target_info, est),
+		.me         = THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name       = "RATEEST",
+		.revision   = 0,
+		.family     = NFPROTO_IPV6,
+		.target     = xt_rateest_tg,
+		.checkentry = xt_rateest_tg_checkentry,
+		.destroy    = xt_rateest_tg_destroy,
+		.targetsize = sizeof(struct xt_rateest_target_info),
+		.usersize   = offsetof(struct xt_rateest_target_info, est),
+		.me         = THIS_MODULE,
+	},
+#endif
 };
 
 static __net_init int xt_rateest_net_init(struct net *net)
@@ -213,12 +228,12 @@
 
 	if (err)
 		return err;
-	return xt_register_target(&xt_rateest_tg_reg);
+	return xt_register_targets(xt_rateest_tg_reg, ARRAY_SIZE(xt_rateest_tg_reg));
 }
 
 static void __exit xt_rateest_tg_fini(void)
 {
-	xt_unregister_target(&xt_rateest_tg_reg);
+	xt_unregister_targets(xt_rateest_tg_reg, ARRAY_SIZE(xt_rateest_tg_reg));
 	unregister_pernet_subsys(&xt_rateest_net_ops);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_REDIRECT.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_REDIRECT.c
@@ -46,7 +46,6 @@
 	nf_ct_netns_put(par->net, par->family);
 }
 
-/* FIXME: Take multiple ranges --RR */
 static int redirect_tg4_check(const struct xt_tgchk_param *par)
 {
 	const struct nf_nat_ipv4_multi_range_compat *mr = par->targinfo;
@@ -65,7 +64,14 @@
 static unsigned int
 redirect_tg4(struct sk_buff *skb, const struct xt_action_param *par)
 {
-	return nf_nat_redirect_ipv4(skb, par->targinfo, xt_hooknum(par));
+	const struct nf_nat_ipv4_multi_range_compat *mr = par->targinfo;
+	struct nf_nat_range2 range = {
+		.flags       = mr->range[0].flags,
+		.min_proto   = mr->range[0].min,
+		.max_proto   = mr->range[0].max,
+	};
+
+	return nf_nat_redirect_ipv4(skb, &range, xt_hooknum(par));
 }
 
 static struct xt_target redirect_tg_reg[] __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_SECMARK.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_SECMARK.c
@@ -42,13 +42,14 @@
 
 static int checkentry_lsm(struct xt_secmark_target_info_v1 *info)
 {
+	struct lsmblob blob;
 	int err;
 
 	info->secctx[SECMARK_SECCTX_MAX - 1] = '\0';
 	info->secid = 0;
 
 	err = security_secctx_to_secid(info->secctx, strlen(info->secctx),
-				       &info->secid);
+				       &blob);
 	if (err) {
 		if (err == -EINVAL)
 			pr_info_ratelimited("invalid security context \'%s\'\n",
@@ -56,13 +57,17 @@
 		return err;
 	}
 
+	/* xt_secmark_target_info can't be changed to use lsmblobs because
+	 * it is exposed as an API. Use lsmblob_value() to get the one
+	 * value that got set by security_secctx_to_secid(). */
+	info->secid = lsmblob_value(&blob);
 	if (!info->secid) {
 		pr_info_ratelimited("unable to map security context \'%s\'\n",
 				    info->secctx);
 		return -ENOENT;
 	}
 
-	err = security_secmark_relabel_packet(info->secid);
+	err = security_secmark_relabel_packet(&blob);
 	if (err) {
 		pr_info_ratelimited("unable to obtain relabeling permission\n");
 		return err;
@@ -157,7 +162,7 @@
 	{
 		.name		= "SECMARK",
 		.revision	= 0,
-		.family		= NFPROTO_UNSPEC,
+		.family		= NFPROTO_IPV4,
 		.checkentry	= secmark_tg_check_v0,
 		.destroy	= secmark_tg_destroy,
 		.target		= secmark_tg_v0,
@@ -167,7 +172,7 @@
 	{
 		.name		= "SECMARK",
 		.revision	= 1,
-		.family		= NFPROTO_UNSPEC,
+		.family		= NFPROTO_IPV4,
 		.checkentry	= secmark_tg_check_v1,
 		.destroy	= secmark_tg_destroy,
 		.target		= secmark_tg_v1,
@@ -175,6 +180,29 @@
 		.usersize	= offsetof(struct xt_secmark_target_info_v1, secid),
 		.me		= THIS_MODULE,
 	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "SECMARK",
+		.revision	= 0,
+		.family		= NFPROTO_IPV6,
+		.checkentry	= secmark_tg_check_v0,
+		.destroy	= secmark_tg_destroy,
+		.target		= secmark_tg_v0,
+		.targetsize	= sizeof(struct xt_secmark_target_info),
+		.me		= THIS_MODULE,
+	},
+	{
+		.name		= "SECMARK",
+		.revision	= 1,
+		.family		= NFPROTO_IPV6,
+		.checkentry	= secmark_tg_check_v1,
+		.destroy	= secmark_tg_destroy,
+		.target		= secmark_tg_v1,
+		.targetsize	= sizeof(struct xt_secmark_target_info_v1),
+		.usersize	= offsetof(struct xt_secmark_target_info_v1, secid),
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static int __init secmark_tg_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_TRACE.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_TRACE.c
@@ -29,25 +29,39 @@
 	return XT_CONTINUE;
 }
 
-static struct xt_target trace_tg_reg __read_mostly = {
-	.name		= "TRACE",
-	.revision	= 0,
-	.family		= NFPROTO_UNSPEC,
-	.table		= "raw",
-	.target		= trace_tg,
-	.checkentry	= trace_tg_check,
-	.destroy	= trace_tg_destroy,
-	.me		= THIS_MODULE,
+static struct xt_target trace_tg_reg[] __read_mostly = {
+	{
+		.name		= "TRACE",
+		.revision	= 0,
+		.family		= NFPROTO_IPV4,
+		.table		= "raw",
+		.target		= trace_tg,
+		.checkentry	= trace_tg_check,
+		.destroy	= trace_tg_destroy,
+		.me		= THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "TRACE",
+		.revision	= 0,
+		.family		= NFPROTO_IPV6,
+		.table		= "raw",
+		.target		= trace_tg,
+		.checkentry	= trace_tg_check,
+		.destroy	= trace_tg_destroy,
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static int __init trace_tg_init(void)
 {
-	return xt_register_target(&trace_tg_reg);
+	return xt_register_targets(trace_tg_reg, ARRAY_SIZE(trace_tg_reg));
 }
 
 static void __exit trace_tg_exit(void)
 {
-	xt_unregister_target(&trace_tg_reg);
+	xt_unregister_targets(trace_tg_reg, ARRAY_SIZE(trace_tg_reg));
 }
 
 module_init(trace_tg_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_addrtype.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_addrtype.c
@@ -208,13 +208,24 @@
 	},
 	{
 		.name		= "addrtype",
-		.family		= NFPROTO_UNSPEC,
+		.family		= NFPROTO_IPV4,
 		.revision	= 1,
 		.match		= addrtype_mt_v1,
 		.checkentry	= addrtype_mt_checkentry_v1,
 		.matchsize	= sizeof(struct xt_addrtype_info_v1),
 		.me		= THIS_MODULE
-	}
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "addrtype",
+		.family		= NFPROTO_IPV6,
+		.revision	= 1,
+		.match		= addrtype_mt_v1,
+		.checkentry	= addrtype_mt_checkentry_v1,
+		.matchsize	= sizeof(struct xt_addrtype_info_v1),
+		.me		= THIS_MODULE
+	},
+#endif
 };
 
 static int __init addrtype_mt_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_cluster.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_cluster.c
@@ -146,24 +146,37 @@
 	nf_ct_netns_put(par->net, par->family);
 }
 
-static struct xt_match xt_cluster_match __read_mostly = {
-	.name		= "cluster",
-	.family		= NFPROTO_UNSPEC,
-	.match		= xt_cluster_mt,
-	.checkentry	= xt_cluster_mt_checkentry,
-	.matchsize	= sizeof(struct xt_cluster_match_info),
-	.destroy	= xt_cluster_mt_destroy,
-	.me		= THIS_MODULE,
+static struct xt_match xt_cluster_match[] __read_mostly = {
+	{
+		.name		= "cluster",
+		.family		= NFPROTO_IPV4,
+		.match		= xt_cluster_mt,
+		.checkentry	= xt_cluster_mt_checkentry,
+		.matchsize	= sizeof(struct xt_cluster_match_info),
+		.destroy	= xt_cluster_mt_destroy,
+		.me		= THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name		= "cluster",
+		.family		= NFPROTO_IPV6,
+		.match		= xt_cluster_mt,
+		.checkentry	= xt_cluster_mt_checkentry,
+		.matchsize	= sizeof(struct xt_cluster_match_info),
+		.destroy	= xt_cluster_mt_destroy,
+		.me		= THIS_MODULE,
+	},
+#endif
 };
 
 static int __init xt_cluster_mt_init(void)
 {
-	return xt_register_match(&xt_cluster_match);
+	return xt_register_matches(xt_cluster_match, ARRAY_SIZE(xt_cluster_match));
 }
 
 static void __exit xt_cluster_mt_fini(void)
 {
-	xt_unregister_match(&xt_cluster_match);
+	xt_unregister_matches(xt_cluster_match, ARRAY_SIZE(xt_cluster_match));
 }
 
 MODULE_AUTHOR("Pablo Neira Ayuso <pablo@netfilter.org>");
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_connbytes.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_connbytes.c
@@ -111,9 +111,11 @@
 		return -EINVAL;
 
 	ret = nf_ct_netns_get(par->net, par->family);
-	if (ret < 0)
+	if (ret < 0) {
 		pr_info_ratelimited("cannot load conntrack support for proto=%u\n",
 				    par->family);
+		return ret;
+	}
 
 	/*
 	 * This filter cannot function correctly unless connection tracking
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_connlimit.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_connlimit.c
@@ -106,26 +106,41 @@
 	nf_conncount_destroy(par->net, par->family, info->data);
 }
 
-static struct xt_match connlimit_mt_reg __read_mostly = {
-	.name       = "connlimit",
-	.revision   = 1,
-	.family     = NFPROTO_UNSPEC,
-	.checkentry = connlimit_mt_check,
-	.match      = connlimit_mt,
-	.matchsize  = sizeof(struct xt_connlimit_info),
-	.usersize   = offsetof(struct xt_connlimit_info, data),
-	.destroy    = connlimit_mt_destroy,
-	.me         = THIS_MODULE,
+static struct xt_match connlimit_mt_reg[] __read_mostly = {
+	{
+		.name       = "connlimit",
+		.revision   = 1,
+		.family     = NFPROTO_IPV4,
+		.checkentry = connlimit_mt_check,
+		.match      = connlimit_mt,
+		.matchsize  = sizeof(struct xt_connlimit_info),
+		.usersize   = offsetof(struct xt_connlimit_info, data),
+		.destroy    = connlimit_mt_destroy,
+		.me         = THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name       = "connlimit",
+		.revision   = 1,
+		.family     = NFPROTO_IPV6,
+		.checkentry = connlimit_mt_check,
+		.match      = connlimit_mt,
+		.matchsize  = sizeof(struct xt_connlimit_info),
+		.usersize   = offsetof(struct xt_connlimit_info, data),
+		.destroy    = connlimit_mt_destroy,
+		.me         = THIS_MODULE,
+	},
+#endif
 };
 
 static int __init connlimit_mt_init(void)
 {
-	return xt_register_match(&connlimit_mt_reg);
+	return xt_register_matches(connlimit_mt_reg, ARRAY_SIZE(connlimit_mt_reg));
 }
 
 static void __exit connlimit_mt_exit(void)
 {
-	xt_unregister_match(&connlimit_mt_reg);
+	xt_unregister_matches(connlimit_mt_reg, ARRAY_SIZE(connlimit_mt_reg));
 }
 
 module_init(connlimit_mt_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_connmark.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_connmark.c
@@ -30,6 +30,7 @@
 	u_int32_t new_targetmark;
 	struct nf_conn *ct;
 	u_int32_t newmark;
+	u_int32_t oldmark;
 
 	ct = nf_ct_get(skb, &ctinfo);
 	if (ct == NULL)
@@ -37,14 +38,15 @@
 
 	switch (info->mode) {
 	case XT_CONNMARK_SET:
-		newmark = (ct->mark & ~info->ctmask) ^ info->ctmark;
+		oldmark = READ_ONCE(ct->mark);
+		newmark = (oldmark & ~info->ctmask) ^ info->ctmark;
 		if (info->shift_dir == D_SHIFT_RIGHT)
 			newmark >>= info->shift_bits;
 		else
 			newmark <<= info->shift_bits;
 
-		if (ct->mark != newmark) {
-			ct->mark = newmark;
+		if (READ_ONCE(ct->mark) != newmark) {
+			WRITE_ONCE(ct->mark, newmark);
 			nf_conntrack_event_cache(IPCT_MARK, ct);
 		}
 		break;
@@ -55,15 +57,15 @@
 		else
 			new_targetmark <<= info->shift_bits;
 
-		newmark = (ct->mark & ~info->ctmask) ^
+		newmark = (READ_ONCE(ct->mark) & ~info->ctmask) ^
 			  new_targetmark;
-		if (ct->mark != newmark) {
-			ct->mark = newmark;
+		if (READ_ONCE(ct->mark) != newmark) {
+			WRITE_ONCE(ct->mark, newmark);
 			nf_conntrack_event_cache(IPCT_MARK, ct);
 		}
 		break;
 	case XT_CONNMARK_RESTORE:
-		new_targetmark = (ct->mark & info->ctmask);
+		new_targetmark = (READ_ONCE(ct->mark) & info->ctmask);
 		if (info->shift_dir == D_SHIFT_RIGHT)
 			new_targetmark >>= info->shift_bits;
 		else
@@ -126,7 +128,7 @@
 	if (ct == NULL)
 		return false;
 
-	return ((ct->mark & info->mask) == info->mark) ^ info->invert;
+	return ((READ_ONCE(ct->mark) & info->mask) == info->mark) ^ info->invert;
 }
 
 static int connmark_mt_check(const struct xt_mtchk_param *par)
@@ -149,7 +151,7 @@
 	{
 		.name           = "CONNMARK",
 		.revision       = 1,
-		.family         = NFPROTO_UNSPEC,
+		.family         = NFPROTO_IPV4,
 		.checkentry     = connmark_tg_check,
 		.target         = connmark_tg,
 		.targetsize     = sizeof(struct xt_connmark_tginfo1),
@@ -159,13 +161,35 @@
 	{
 		.name           = "CONNMARK",
 		.revision       = 2,
-		.family         = NFPROTO_UNSPEC,
+		.family         = NFPROTO_IPV4,
 		.checkentry     = connmark_tg_check,
 		.target         = connmark_tg_v2,
 		.targetsize     = sizeof(struct xt_connmark_tginfo2),
 		.destroy        = connmark_tg_destroy,
 		.me             = THIS_MODULE,
-	}
+	},
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name           = "CONNMARK",
+		.revision       = 1,
+		.family         = NFPROTO_IPV6,
+		.checkentry     = connmark_tg_check,
+		.target         = connmark_tg,
+		.targetsize     = sizeof(struct xt_connmark_tginfo1),
+		.destroy        = connmark_tg_destroy,
+		.me             = THIS_MODULE,
+	},
+	{
+		.name           = "CONNMARK",
+		.revision       = 2,
+		.family         = NFPROTO_IPV6,
+		.checkentry     = connmark_tg_check,
+		.target         = connmark_tg_v2,
+		.targetsize     = sizeof(struct xt_connmark_tginfo2),
+		.destroy        = connmark_tg_destroy,
+		.me             = THIS_MODULE,
+	},
+#endif
 };
 
 static struct xt_match connmark_mt_reg __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_mark.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_mark.c
@@ -39,13 +39,35 @@
 	return ((skb->mark & info->mask) == info->mark) ^ info->invert;
 }
 
-static struct xt_target mark_tg_reg __read_mostly = {
-	.name           = "MARK",
-	.revision       = 2,
-	.family         = NFPROTO_UNSPEC,
-	.target         = mark_tg,
-	.targetsize     = sizeof(struct xt_mark_tginfo2),
-	.me             = THIS_MODULE,
+static struct xt_target mark_tg_reg[] __read_mostly = {
+	{
+		.name           = "MARK",
+		.revision       = 2,
+		.family         = NFPROTO_IPV4,
+		.target         = mark_tg,
+		.targetsize     = sizeof(struct xt_mark_tginfo2),
+		.me             = THIS_MODULE,
+	},
+#if IS_ENABLED(CONFIG_IP_NF_ARPTABLES)
+	{
+		.name           = "MARK",
+		.revision       = 2,
+		.family         = NFPROTO_ARP,
+		.target         = mark_tg,
+		.targetsize     = sizeof(struct xt_mark_tginfo2),
+		.me             = THIS_MODULE,
+	},
+#endif
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
+	{
+		.name           = "MARK",
+		.revision       = 2,
+		.family         = NFPROTO_IPV6,
+		.target         = mark_tg,
+		.targetsize     = sizeof(struct xt_mark_tginfo2),
+		.me             = THIS_MODULE,
+	},
+#endif
 };
 
 static struct xt_match mark_mt_reg __read_mostly = {
@@ -61,12 +83,12 @@
 {
 	int ret;
 
-	ret = xt_register_target(&mark_tg_reg);
+	ret = xt_register_targets(mark_tg_reg, ARRAY_SIZE(mark_tg_reg));
 	if (ret < 0)
 		return ret;
 	ret = xt_register_match(&mark_mt_reg);
 	if (ret < 0) {
-		xt_unregister_target(&mark_tg_reg);
+		xt_unregister_targets(mark_tg_reg, ARRAY_SIZE(mark_tg_reg));
 		return ret;
 	}
 	return 0;
@@ -75,7 +97,7 @@
 static void __exit mark_mt_exit(void)
 {
 	xt_unregister_match(&mark_mt_reg);
-	xt_unregister_target(&mark_tg_reg);
+	xt_unregister_targets(mark_tg_reg, ARRAY_SIZE(mark_tg_reg));
 }
 
 module_init(mark_mt_init);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_osf.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_osf.c
@@ -71,4 +71,3 @@
 MODULE_DESCRIPTION("Passive OS fingerprint matching.");
 MODULE_ALIAS("ipt_osf");
 MODULE_ALIAS("ip6t_osf");
-MODULE_ALIAS_NFNL_SUBSYS(NFNL_SUBSYS_OSF);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_owner.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_owner.c
@@ -76,18 +76,23 @@
 		 */
 		return false;
 
-	filp = sk->sk_socket->file;
-	if (filp == NULL)
+	read_lock_bh(&sk->sk_callback_lock);
+	filp = sk->sk_socket ? sk->sk_socket->file : NULL;
+	if (filp == NULL) {
+		read_unlock_bh(&sk->sk_callback_lock);
 		return ((info->match ^ info->invert) &
 		       (XT_OWNER_UID | XT_OWNER_GID)) == 0;
+	}
 
 	if (info->match & XT_OWNER_UID) {
 		kuid_t uid_min = make_kuid(net->user_ns, info->uid_min);
 		kuid_t uid_max = make_kuid(net->user_ns, info->uid_max);
 		if ((uid_gte(filp->f_cred->fsuid, uid_min) &&
 		     uid_lte(filp->f_cred->fsuid, uid_max)) ^
-		    !(info->invert & XT_OWNER_UID))
+		    !(info->invert & XT_OWNER_UID)) {
+			read_unlock_bh(&sk->sk_callback_lock);
 			return false;
+		}
 	}
 
 	if (info->match & XT_OWNER_GID) {
@@ -112,10 +117,13 @@
 			}
 		}
 
-		if (match ^ !(info->invert & XT_OWNER_GID))
+		if (match ^ !(info->invert & XT_OWNER_GID)) {
+			read_unlock_bh(&sk->sk_callback_lock);
 			return false;
+		}
 	}
 
+	read_unlock_bh(&sk->sk_callback_lock);
 	return true;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_recent.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_recent.c
@@ -561,7 +561,7 @@
 {
 	struct recent_table *t = PDE_DATA(file_inode(file));
 	struct recent_entry *e;
-	char buf[sizeof("+b335:1d35:1e55:dead:c0de:1715:5afe:c0de")];
+	char buf[sizeof("+b335:1d35:1e55:dead:c0de:1715:255.255.255.255")];
 	const char *c = buf;
 	union nf_inet_addr addr = {};
 	u_int16_t family;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_sctp.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_sctp.c
@@ -150,6 +150,8 @@
 {
 	const struct xt_sctp_info *info = par->matchinfo;
 
+	if (info->flag_count > ARRAY_SIZE(info->flag_info))
+		return -EINVAL;
 	if (info->flags & ~XT_SCTP_VALID_FLAGS)
 		return -EINVAL;
 	if (info->invflags & ~XT_SCTP_VALID_FLAGS)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_socket.c
@@ -220,8 +220,10 @@
 {
 	if (par->family == NFPROTO_IPV4)
 		nf_defrag_ipv4_disable(par->net);
+#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
 	else if (par->family == NFPROTO_IPV6)
-		nf_defrag_ipv4_disable(par->net);
+		nf_defrag_ipv6_disable(par->net);
+#endif
 }
 
 static struct xt_match socket_mt_reg[] __read_mostly = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/netfilter/xt_u32.c
+++ linux-xilinx-zynqmp-5.15.0/net/netfilter/xt_u32.c
@@ -96,11 +96,32 @@
 	return ret ^ data->invert;
 }
 
+static int u32_mt_checkentry(const struct xt_mtchk_param *par)
+{
+	const struct xt_u32 *data = par->matchinfo;
+	const struct xt_u32_test *ct;
+	unsigned int i;
+
+	if (data->ntests > ARRAY_SIZE(data->tests))
+		return -EINVAL;
+
+	for (i = 0; i < data->ntests; ++i) {
+		ct = &data->tests[i];
+
+		if (ct->nnums > ARRAY_SIZE(ct->location) ||
+		    ct->nvalues > ARRAY_SIZE(ct->value))
+			return -EINVAL;
+	}
+
+	return 0;
+}
+
 static struct xt_match xt_u32_mt_reg __read_mostly = {
 	.name       = "u32",
 	.revision   = 0,
 	.family     = NFPROTO_UNSPEC,
 	.match      = u32_mt,
+	.checkentry = u32_mt_checkentry,
 	.matchsize  = sizeof(struct xt_u32),
 	.me         = THIS_MODULE,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlabel/netlabel_calipso.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlabel/netlabel_calipso.c
@@ -54,6 +54,28 @@
 	[NLBL_CALIPSO_A_MTYPE] = { .type = NLA_U32 },
 };
 
+static const struct netlbl_calipso_ops *calipso_ops;
+
+/**
+ * netlbl_calipso_ops_register - Register the CALIPSO operations
+ * @ops: ops to register
+ *
+ * Description:
+ * Register the CALIPSO packet engine operations.
+ *
+ */
+const struct netlbl_calipso_ops *
+netlbl_calipso_ops_register(const struct netlbl_calipso_ops *ops)
+{
+	return xchg(&calipso_ops, ops);
+}
+EXPORT_SYMBOL(netlbl_calipso_ops_register);
+
+static const struct netlbl_calipso_ops *netlbl_calipso_ops_get(void)
+{
+	return READ_ONCE(calipso_ops);
+}
+
 /* NetLabel Command Handlers
  */
 /**
@@ -96,15 +118,18 @@
  *
  */
 static int netlbl_calipso_add(struct sk_buff *skb, struct genl_info *info)
-
 {
 	int ret_val = -EINVAL;
 	struct netlbl_audit audit_info;
+	const struct netlbl_calipso_ops *ops = netlbl_calipso_ops_get();
 
 	if (!info->attrs[NLBL_CALIPSO_A_DOI] ||
 	    !info->attrs[NLBL_CALIPSO_A_MTYPE])
 		return -EINVAL;
 
+	if (!ops)
+		return -EOPNOTSUPP;
+
 	netlbl_netlink_auditinfo(&audit_info);
 	switch (nla_get_u32(info->attrs[NLBL_CALIPSO_A_MTYPE])) {
 	case CALIPSO_MAP_PASS:
@@ -362,28 +387,6 @@
 	return genl_register_family(&netlbl_calipso_gnl_family);
 }
 
-static const struct netlbl_calipso_ops *calipso_ops;
-
-/**
- * netlbl_calipso_ops_register - Register the CALIPSO operations
- * @ops: ops to register
- *
- * Description:
- * Register the CALIPSO packet engine operations.
- *
- */
-const struct netlbl_calipso_ops *
-netlbl_calipso_ops_register(const struct netlbl_calipso_ops *ops)
-{
-	return xchg(&calipso_ops, ops);
-}
-EXPORT_SYMBOL(netlbl_calipso_ops_register);
-
-static const struct netlbl_calipso_ops *netlbl_calipso_ops_get(void)
-{
-	return READ_ONCE(calipso_ops);
-}
-
 /**
  * calipso_doi_add - Add a new DOI to the CALIPSO protocol engine
  * @doi_def: the DOI structure
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlabel/netlabel_kapi.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlabel/netlabel_kapi.c
@@ -196,7 +196,7 @@
  * @addr: IP address in network byte order (struct in[6]_addr)
  * @mask: address mask in network byte order (struct in[6]_addr)
  * @family: address family
- * @secid: LSM secid value for the entry
+ * @lsmblob: LSM data value for the entry
  * @audit_info: NetLabel audit information
  *
  * Description:
@@ -210,7 +210,7 @@
 				const void *addr,
 				const void *mask,
 				u16 family,
-				u32 secid,
+				struct lsmblob *lsmblob,
 				struct netlbl_audit *audit_info)
 {
 	u32 addr_len;
@@ -230,7 +230,7 @@
 
 	return netlbl_unlhsh_add(net,
 				 dev_name, addr, mask, addr_len,
-				 secid, audit_info);
+				 lsmblob, audit_info);
 }
 
 /**
@@ -857,7 +857,8 @@
 
 	offset -= iter->startbit;
 	idx = offset / NETLBL_CATMAP_MAPSIZE;
-	iter->bitmap[idx] |= bitmap << (offset % NETLBL_CATMAP_MAPSIZE);
+	iter->bitmap[idx] |= (NETLBL_CATMAP_MAPTYPE)bitmap
+			     << (offset % NETLBL_CATMAP_MAPSIZE);
 
 	return 0;
 }
@@ -885,6 +886,8 @@
 	unsigned char bitmask;
 	unsigned char byte;
 
+	if (offset >= bitmap_len)
+		return -1;
 	byte_offset = offset / 8;
 	byte = bitmap[byte_offset];
 	bit_spot = offset;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlabel/netlabel_unlabeled.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlabel/netlabel_unlabeled.c
@@ -66,7 +66,7 @@
 #define netlbl_unlhsh_addr4_entry(iter) \
 	container_of(iter, struct netlbl_unlhsh_addr4, list)
 struct netlbl_unlhsh_addr4 {
-	u32 secid;
+	struct lsmblob lsmblob;
 
 	struct netlbl_af4list list;
 	struct rcu_head rcu;
@@ -74,7 +74,7 @@
 #define netlbl_unlhsh_addr6_entry(iter) \
 	container_of(iter, struct netlbl_unlhsh_addr6, list)
 struct netlbl_unlhsh_addr6 {
-	u32 secid;
+	struct lsmblob lsmblob;
 
 	struct netlbl_af6list list;
 	struct rcu_head rcu;
@@ -220,7 +220,7 @@
  * @iface: the associated interface entry
  * @addr: IPv4 address in network byte order
  * @mask: IPv4 address mask in network byte order
- * @secid: LSM secid value for entry
+ * @lsmblob: LSM data value for entry
  *
  * Description:
  * Add a new address entry into the unlabeled connection hash table using the
@@ -231,7 +231,7 @@
 static int netlbl_unlhsh_add_addr4(struct netlbl_unlhsh_iface *iface,
 				   const struct in_addr *addr,
 				   const struct in_addr *mask,
-				   u32 secid)
+				   struct lsmblob *lsmblob)
 {
 	int ret_val;
 	struct netlbl_unlhsh_addr4 *entry;
@@ -243,7 +243,7 @@
 	entry->list.addr = addr->s_addr & mask->s_addr;
 	entry->list.mask = mask->s_addr;
 	entry->list.valid = 1;
-	entry->secid = secid;
+	entry->lsmblob = *lsmblob;
 
 	spin_lock(&netlbl_unlhsh_lock);
 	ret_val = netlbl_af4list_add(&entry->list, &iface->addr4_list);
@@ -260,7 +260,7 @@
  * @iface: the associated interface entry
  * @addr: IPv6 address in network byte order
  * @mask: IPv6 address mask in network byte order
- * @secid: LSM secid value for entry
+ * @lsmblob: LSM data value for entry
  *
  * Description:
  * Add a new address entry into the unlabeled connection hash table using the
@@ -271,7 +271,7 @@
 static int netlbl_unlhsh_add_addr6(struct netlbl_unlhsh_iface *iface,
 				   const struct in6_addr *addr,
 				   const struct in6_addr *mask,
-				   u32 secid)
+				   struct lsmblob *lsmblob)
 {
 	int ret_val;
 	struct netlbl_unlhsh_addr6 *entry;
@@ -287,7 +287,7 @@
 	entry->list.addr.s6_addr32[3] &= mask->s6_addr32[3];
 	entry->list.mask = *mask;
 	entry->list.valid = 1;
-	entry->secid = secid;
+	entry->lsmblob = *lsmblob;
 
 	spin_lock(&netlbl_unlhsh_lock);
 	ret_val = netlbl_af6list_add(&entry->list, &iface->addr6_list);
@@ -366,7 +366,7 @@
 		      const void *addr,
 		      const void *mask,
 		      u32 addr_len,
-		      u32 secid,
+		      struct lsmblob *lsmblob,
 		      struct netlbl_audit *audit_info)
 {
 	int ret_val;
@@ -374,8 +374,7 @@
 	struct net_device *dev;
 	struct netlbl_unlhsh_iface *iface;
 	struct audit_buffer *audit_buf = NULL;
-	char *secctx = NULL;
-	u32 secctx_len;
+	struct lsmcontext context;
 
 	if (addr_len != sizeof(struct in_addr) &&
 	    addr_len != sizeof(struct in6_addr))
@@ -408,7 +407,7 @@
 		const struct in_addr *addr4 = addr;
 		const struct in_addr *mask4 = mask;
 
-		ret_val = netlbl_unlhsh_add_addr4(iface, addr4, mask4, secid);
+		ret_val = netlbl_unlhsh_add_addr4(iface, addr4, mask4, lsmblob);
 		if (audit_buf != NULL)
 			netlbl_af4list_audit_addr(audit_buf, 1,
 						  dev_name,
@@ -421,7 +420,7 @@
 		const struct in6_addr *addr6 = addr;
 		const struct in6_addr *mask6 = mask;
 
-		ret_val = netlbl_unlhsh_add_addr6(iface, addr6, mask6, secid);
+		ret_val = netlbl_unlhsh_add_addr6(iface, addr6, mask6, lsmblob);
 		if (audit_buf != NULL)
 			netlbl_af6list_audit_addr(audit_buf, 1,
 						  dev_name,
@@ -438,11 +437,11 @@
 unlhsh_add_return:
 	rcu_read_unlock();
 	if (audit_buf != NULL) {
-		if (security_secid_to_secctx(secid,
-					     &secctx,
-					     &secctx_len) == 0) {
-			audit_log_format(audit_buf, " sec_obj=%s", secctx);
-			security_release_secctx(secctx, secctx_len);
+		if (security_secid_to_secctx(lsmblob, &context,
+					     LSMBLOB_FIRST) == 0) {
+			audit_log_format(audit_buf, " sec_obj=%s",
+					 context.context);
+			security_release_secctx(&context);
 		}
 		audit_log_format(audit_buf, " res=%u", ret_val == 0 ? 1 : 0);
 		audit_log_end(audit_buf);
@@ -473,8 +472,7 @@
 	struct netlbl_unlhsh_addr4 *entry;
 	struct audit_buffer *audit_buf;
 	struct net_device *dev;
-	char *secctx;
-	u32 secctx_len;
+	struct lsmcontext context;
 
 	spin_lock(&netlbl_unlhsh_lock);
 	list_entry = netlbl_af4list_remove(addr->s_addr, mask->s_addr,
@@ -494,10 +492,11 @@
 					  addr->s_addr, mask->s_addr);
 		dev_put(dev);
 		if (entry != NULL &&
-		    security_secid_to_secctx(entry->secid,
-					     &secctx, &secctx_len) == 0) {
-			audit_log_format(audit_buf, " sec_obj=%s", secctx);
-			security_release_secctx(secctx, secctx_len);
+		    security_secid_to_secctx(&entry->lsmblob, &context,
+					     LSMBLOB_FIRST) == 0) {
+			audit_log_format(audit_buf, " sec_obj=%s",
+					 context.context);
+			security_release_secctx(&context);
 		}
 		audit_log_format(audit_buf, " res=%u", entry != NULL ? 1 : 0);
 		audit_log_end(audit_buf);
@@ -534,8 +533,7 @@
 	struct netlbl_unlhsh_addr6 *entry;
 	struct audit_buffer *audit_buf;
 	struct net_device *dev;
-	char *secctx;
-	u32 secctx_len;
+	struct lsmcontext context;
 
 	spin_lock(&netlbl_unlhsh_lock);
 	list_entry = netlbl_af6list_remove(addr, mask, &iface->addr6_list);
@@ -554,10 +552,11 @@
 					  addr, mask);
 		dev_put(dev);
 		if (entry != NULL &&
-		    security_secid_to_secctx(entry->secid,
-					     &secctx, &secctx_len) == 0) {
-			audit_log_format(audit_buf, " sec_obj=%s", secctx);
-			security_release_secctx(secctx, secctx_len);
+		    security_secid_to_secctx(&entry->lsmblob, &context,
+					     LSMBLOB_FIRST) == 0) {
+			audit_log_format(audit_buf, " sec_obj=%s",
+					 context.context);
+			security_release_secctx(&context);
 		}
 		audit_log_format(audit_buf, " res=%u", entry != NULL ? 1 : 0);
 		audit_log_end(audit_buf);
@@ -880,7 +879,7 @@
 	void *addr;
 	void *mask;
 	u32 addr_len;
-	u32 secid;
+	struct lsmblob blob;
 	struct netlbl_audit audit_info;
 
 	/* Don't allow users to add both IPv4 and IPv6 addresses for a
@@ -904,13 +903,12 @@
 	ret_val = security_secctx_to_secid(
 		                  nla_data(info->attrs[NLBL_UNLABEL_A_SECCTX]),
 				  nla_len(info->attrs[NLBL_UNLABEL_A_SECCTX]),
-				  &secid);
+				  &blob);
 	if (ret_val != 0)
 		return ret_val;
 
-	return netlbl_unlhsh_add(&init_net,
-				 dev_name, addr, mask, addr_len, secid,
-				 &audit_info);
+	return netlbl_unlhsh_add(&init_net, dev_name, addr, mask, addr_len,
+				 &blob, &audit_info);
 }
 
 /**
@@ -931,7 +929,7 @@
 	void *addr;
 	void *mask;
 	u32 addr_len;
-	u32 secid;
+	struct lsmblob blob;
 	struct netlbl_audit audit_info;
 
 	/* Don't allow users to add both IPv4 and IPv6 addresses for a
@@ -953,12 +951,11 @@
 	ret_val = security_secctx_to_secid(
 		                  nla_data(info->attrs[NLBL_UNLABEL_A_SECCTX]),
 				  nla_len(info->attrs[NLBL_UNLABEL_A_SECCTX]),
-				  &secid);
+				  &blob);
 	if (ret_val != 0)
 		return ret_val;
 
-	return netlbl_unlhsh_add(&init_net,
-				 NULL, addr, mask, addr_len, secid,
+	return netlbl_unlhsh_add(&init_net, NULL, addr, mask, addr_len, &blob,
 				 &audit_info);
 }
 
@@ -1069,10 +1066,9 @@
 	int ret_val = -ENOMEM;
 	struct netlbl_unlhsh_walk_arg *cb_arg = arg;
 	struct net_device *dev;
+	struct lsmcontext context;
 	void *data;
-	u32 secid;
-	char *secctx;
-	u32 secctx_len;
+	struct lsmblob *lsmb;
 
 	data = genlmsg_put(cb_arg->skb, NETLINK_CB(cb_arg->nl_cb->skb).portid,
 			   cb_arg->seq, &netlbl_unlabel_gnl_family,
@@ -1110,7 +1106,7 @@
 		if (ret_val != 0)
 			goto list_cb_failure;
 
-		secid = addr4->secid;
+		lsmb = (struct lsmblob *)&addr4->lsmblob;
 	} else {
 		ret_val = nla_put_in6_addr(cb_arg->skb,
 					   NLBL_UNLABEL_A_IPV6ADDR,
@@ -1124,17 +1120,17 @@
 		if (ret_val != 0)
 			goto list_cb_failure;
 
-		secid = addr6->secid;
+		lsmb = (struct lsmblob *)&addr6->lsmblob;
 	}
 
-	ret_val = security_secid_to_secctx(secid, &secctx, &secctx_len);
+	ret_val = security_secid_to_secctx(lsmb, &context, LSMBLOB_FIRST);
 	if (ret_val != 0)
 		goto list_cb_failure;
 	ret_val = nla_put(cb_arg->skb,
 			  NLBL_UNLABEL_A_SECCTX,
-			  secctx_len,
-			  secctx);
-	security_release_secctx(secctx, secctx_len);
+			  context.len,
+			  context.context);
+	security_release_secctx(&context);
 	if (ret_val != 0)
 		goto list_cb_failure;
 
@@ -1486,7 +1482,7 @@
 					      &iface->addr4_list);
 		if (addr4 == NULL)
 			goto unlabel_getattr_nolabel;
-		secattr->attr.secid = netlbl_unlhsh_addr4_entry(addr4)->secid;
+		secattr->attr.lsmblob = netlbl_unlhsh_addr4_entry(addr4)->lsmblob;
 		break;
 	}
 #if IS_ENABLED(CONFIG_IPV6)
@@ -1499,7 +1495,7 @@
 					      &iface->addr6_list);
 		if (addr6 == NULL)
 			goto unlabel_getattr_nolabel;
-		secattr->attr.secid = netlbl_unlhsh_addr6_entry(addr6)->secid;
+		secattr->attr.lsmblob = netlbl_unlhsh_addr6_entry(addr6)->lsmblob;
 		break;
 	}
 #endif /* IPv6 */
@@ -1537,7 +1533,7 @@
 	/* Only the kernel is allowed to call this function and the only time
 	 * it is called is at bootup before the audit subsystem is reporting
 	 * messages so don't worry to much about these values. */
-	security_task_getsecid_subj(current, &audit_info.secid);
+	security_task_getsecid_subj(current, &audit_info.lsmdata);
 	audit_info.loginuid = GLOBAL_ROOT_UID;
 	audit_info.sessionid = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlabel/netlabel_unlabeled.h
+++ linux-xilinx-zynqmp-5.15.0/net/netlabel/netlabel_unlabeled.h
@@ -211,7 +211,7 @@
 		      const void *addr,
 		      const void *mask,
 		      u32 addr_len,
-		      u32 secid,
+		      struct lsmblob *lsmblob,
 		      struct netlbl_audit *audit_info);
 int netlbl_unlhsh_remove(struct net *net,
 			 const char *dev_name,
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlabel/netlabel_user.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlabel/netlabel_user.c
@@ -84,12 +84,12 @@
 					       struct netlbl_audit *audit_info)
 {
 	struct audit_buffer *audit_buf;
-	char *secctx;
-	u32 secctx_len;
 
 	if (audit_enabled == AUDIT_OFF)
 		return NULL;
 
+	audit_stamp_context(audit_context());
+
 	audit_buf = audit_log_start(audit_context(), GFP_ATOMIC, type);
 	if (audit_buf == NULL)
 		return NULL;
@@ -98,13 +98,8 @@
 			 from_kuid(&init_user_ns, audit_info->loginuid),
 			 audit_info->sessionid);
 
-	if (audit_info->secid != 0 &&
-	    security_secid_to_secctx(audit_info->secid,
-				     &secctx,
-				     &secctx_len) == 0) {
-		audit_log_format(audit_buf, " subj=%s", secctx);
-		security_release_secctx(secctx, secctx_len);
-	}
+	audit_log_task_context(audit_buf, &audit_info->lsmdata);
+	audit_log_lsm(&audit_info->lsmdata, false);
 
 	return audit_buf;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlabel/netlabel_user.h
+++ linux-xilinx-zynqmp-5.15.0/net/netlabel/netlabel_user.h
@@ -32,7 +32,7 @@
  */
 static inline void netlbl_netlink_auditinfo(struct netlbl_audit *audit_info)
 {
-	security_task_getsecid_subj(current, &audit_info->secid);
+	security_task_getsecid_subj(current, &audit_info->lsmdata);
 	audit_info->loginuid = audit_get_loginuid(current);
 	audit_info->sessionid = audit_get_sessionid(current);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlink/af_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlink/af_netlink.c
@@ -128,7 +128,7 @@
 	"nlk_cb_mutex-MAX_LINKS"
 };
 
-static int netlink_dump(struct sock *sk);
+static int netlink_dump(struct sock *sk, bool lock_taken);
 
 /* nl_table locking explained:
  * Lookup and traversal are protected with an RCU read-side lock. Insertion
@@ -157,13 +157,15 @@
 
 static inline u32 netlink_group_mask(u32 group)
 {
+	if (group > 32)
+		return 0;
 	return group ? 1 << (group - 1) : 0;
 }
 
 static struct sk_buff *netlink_to_full_skb(const struct sk_buff *skb,
 					   gfp_t gfp_mask)
 {
-	unsigned int len = skb_end_offset(skb);
+	unsigned int len = skb->len;
 	struct sk_buff *new;
 
 	new = alloc_skb(len, gfp_mask);
@@ -350,7 +352,7 @@
 	if (!(nlk->flags & NETLINK_F_RECV_NO_ENOBUFS)) {
 		if (!test_and_set_bit(NETLINK_S_CONGESTED,
 				      &nlk_sk(sk)->state)) {
-			sk->sk_err = ENOBUFS;
+			WRITE_ONCE(sk->sk_err, ENOBUFS);
 			sk_error_report(sk);
 		}
 	}
@@ -372,7 +374,7 @@
 	if (is_vmalloc_addr(skb->head)) {
 		if (!skb->cloned ||
 		    !atomic_dec_return(&(skb_shinfo(skb)->dataref)))
-			vfree(skb->head);
+			vfree_atomic(skb->head);
 
 		skb->head = NULL;
 	}
@@ -391,15 +393,6 @@
 
 static void netlink_sock_destruct(struct sock *sk)
 {
-	struct netlink_sock *nlk = nlk_sk(sk);
-
-	if (nlk->cb_running) {
-		if (nlk->cb.done)
-			nlk->cb.done(&nlk->cb);
-		module_put(nlk->cb.module);
-		kfree_skb(nlk->cb.skb);
-	}
-
 	skb_queue_purge(&sk->sk_receive_queue);
 
 	if (!sock_flag(sk, SOCK_DEAD)) {
@@ -412,14 +405,6 @@
 	WARN_ON(nlk_sk(sk)->groups);
 }
 
-static void netlink_sock_destruct_work(struct work_struct *work)
-{
-	struct netlink_sock *nlk = container_of(work, struct netlink_sock,
-						work);
-
-	sk_free(&nlk->sk);
-}
-
 /* This lock without WQ_FLAG_EXCLUSIVE is good on UP and it is _very_ bad on
  * SMP. Look, when several writers sleep and reader wakes them up, all but one
  * immediately hit write lock and grab all the cpus. Exclusive sleep solves
@@ -576,7 +561,9 @@
 	if (nlk_sk(sk)->bound)
 		goto err;
 
-	nlk_sk(sk)->portid = portid;
+	/* portid can be read locklessly from netlink_getname(). */
+	WRITE_ONCE(nlk_sk(sk)->portid, portid);
+
 	sock_hold(sk);
 
 	err = __netlink_insert(table, sk);
@@ -707,9 +694,7 @@
 	if (err < 0)
 		goto out_module;
 
-	local_bh_disable();
 	sock_prot_inuse_add(net, &netlink_proto, 1);
-	local_bh_enable();
 
 	nlk = nlk_sk(sock->sk);
 	nlk->module = module;
@@ -734,12 +719,6 @@
 	if (!refcount_dec_and_test(&sk->sk_refcnt))
 		return;
 
-	if (nlk->cb_running && nlk->cb.done) {
-		INIT_WORK(&nlk->work, netlink_sock_destruct_work);
-		schedule_work(&nlk->work);
-		return;
-	}
-
 	sk_free(sk);
 }
 
@@ -789,6 +768,14 @@
 				NETLINK_URELEASE, &n);
 	}
 
+	/* Terminate any outstanding dump */
+	if (nlk->cb_running) {
+		if (nlk->cb.done)
+			nlk->cb.done(&nlk->cb);
+		module_put(nlk->cb.module);
+		kfree_skb(nlk->cb.skb);
+	}
+
 	module_put(nlk->module);
 
 	if (netlink_is_kernel(sk)) {
@@ -809,9 +796,7 @@
 		netlink_table_ungrab();
 	}
 
-	local_bh_disable();
 	sock_prot_inuse_add(sock_net(sk), &netlink_proto, -1);
-	local_bh_enable();
 	call_rcu(&nlk->rcu, deferred_put_nlk_sk);
 	return 0;
 }
@@ -1085,9 +1070,11 @@
 		return -EINVAL;
 
 	if (addr->sa_family == AF_UNSPEC) {
-		sk->sk_state	= NETLINK_UNCONNECTED;
-		nlk->dst_portid	= 0;
-		nlk->dst_group  = 0;
+		/* paired with READ_ONCE() in netlink_getsockbyportid() */
+		WRITE_ONCE(sk->sk_state, NETLINK_UNCONNECTED);
+		/* dst_portid and dst_group can be read locklessly */
+		WRITE_ONCE(nlk->dst_portid, 0);
+		WRITE_ONCE(nlk->dst_group, 0);
 		return 0;
 	}
 	if (addr->sa_family != AF_NETLINK)
@@ -1108,9 +1095,11 @@
 		err = netlink_autobind(sock);
 
 	if (err == 0) {
-		sk->sk_state	= NETLINK_CONNECTED;
-		nlk->dst_portid = nladdr->nl_pid;
-		nlk->dst_group  = ffs(nladdr->nl_groups);
+		/* paired with READ_ONCE() in netlink_getsockbyportid() */
+		WRITE_ONCE(sk->sk_state, NETLINK_CONNECTED);
+		/* dst_portid and dst_group can be read locklessly */
+		WRITE_ONCE(nlk->dst_portid, nladdr->nl_pid);
+		WRITE_ONCE(nlk->dst_group, ffs(nladdr->nl_groups));
 	}
 
 	return err;
@@ -1127,10 +1116,12 @@
 	nladdr->nl_pad = 0;
 
 	if (peer) {
-		nladdr->nl_pid = nlk->dst_portid;
-		nladdr->nl_groups = netlink_group_mask(nlk->dst_group);
+		/* Paired with WRITE_ONCE() in netlink_connect() */
+		nladdr->nl_pid = READ_ONCE(nlk->dst_portid);
+		nladdr->nl_groups = netlink_group_mask(READ_ONCE(nlk->dst_group));
 	} else {
-		nladdr->nl_pid = nlk->portid;
+		/* Paired with WRITE_ONCE() in netlink_insert() */
+		nladdr->nl_pid = READ_ONCE(nlk->portid);
 		netlink_lock_table();
 		nladdr->nl_groups = nlk->groups ? nlk->groups[0] : 0;
 		netlink_unlock_table();
@@ -1157,8 +1148,9 @@
 
 	/* Don't bother queuing skb if kernel socket has no input function */
 	nlk = nlk_sk(sock);
-	if (sock->sk_state == NETLINK_CONNECTED &&
-	    nlk->dst_portid != nlk_sk(ssk)->portid) {
+	/* dst_portid and sk_state can be changed in netlink_connect() */
+	if (READ_ONCE(sock->sk_state) == NETLINK_CONNECTED &&
+	    READ_ONCE(nlk->dst_portid) != nlk_sk(ssk)->portid) {
 		sock_put(sock);
 		return ERR_PTR(-ECONNREFUSED);
 	}
@@ -1580,7 +1572,7 @@
 		goto out;
 	}
 
-	sk->sk_err = p->code;
+	WRITE_ONCE(sk->sk_err, p->code);
 	sk_error_report(sk);
 out:
 	return ret;
@@ -1599,6 +1591,7 @@
 int netlink_set_err(struct sock *ssk, u32 portid, u32 group, int code)
 {
 	struct netlink_set_err_data info;
+	unsigned long flags;
 	struct sock *sk;
 	int ret = 0;
 
@@ -1608,12 +1601,12 @@
 	/* sk->sk_err wants a positive error value */
 	info.code = -code;
 
-	read_lock(&nl_table_lock);
+	read_lock_irqsave(&nl_table_lock, flags);
 
 	sk_for_each_bound(sk, &nl_table[ssk->sk_protocol].mc_list)
 		ret += do_one_set_err(sk, &info);
 
-	read_unlock(&nl_table_lock);
+	read_unlock_irqrestore(&nl_table_lock, flags);
 	return ret;
 }
 EXPORT_SYMBOL(netlink_set_err);
@@ -1741,7 +1734,8 @@
 {
 	struct sock *sk = sock->sk;
 	struct netlink_sock *nlk = nlk_sk(sk);
-	int len, val, err;
+	unsigned int flag;
+	int len, val;
 
 	if (level != SOL_NETLINK)
 		return -ENOPROTOOPT;
@@ -1753,39 +1747,17 @@
 
 	switch (optname) {
 	case NETLINK_PKTINFO:
-		if (len < sizeof(int))
-			return -EINVAL;
-		len = sizeof(int);
-		val = nlk->flags & NETLINK_F_RECV_PKTINFO ? 1 : 0;
-		if (put_user(len, optlen) ||
-		    put_user(val, optval))
-			return -EFAULT;
-		err = 0;
+		flag = NETLINK_F_RECV_PKTINFO;
 		break;
 	case NETLINK_BROADCAST_ERROR:
-		if (len < sizeof(int))
-			return -EINVAL;
-		len = sizeof(int);
-		val = nlk->flags & NETLINK_F_BROADCAST_SEND_ERROR ? 1 : 0;
-		if (put_user(len, optlen) ||
-		    put_user(val, optval))
-			return -EFAULT;
-		err = 0;
+		flag = NETLINK_F_BROADCAST_SEND_ERROR;
 		break;
 	case NETLINK_NO_ENOBUFS:
-		if (len < sizeof(int))
-			return -EINVAL;
-		len = sizeof(int);
-		val = nlk->flags & NETLINK_F_RECV_NO_ENOBUFS ? 1 : 0;
-		if (put_user(len, optlen) ||
-		    put_user(val, optval))
-			return -EFAULT;
-		err = 0;
+		flag = NETLINK_F_RECV_NO_ENOBUFS;
 		break;
 	case NETLINK_LIST_MEMBERSHIPS: {
-		int pos, idx, shift;
+		int pos, idx, shift, err = 0;
 
-		err = 0;
 		netlink_lock_table();
 		for (pos = 0; pos * 8 < nlk->ngroups; pos += sizeof(u32)) {
 			if (len - pos < sizeof(u32))
@@ -1799,43 +1771,35 @@
 				break;
 			}
 		}
-		if (put_user(ALIGN(nlk->ngroups / 8, sizeof(u32)), optlen))
+		if (put_user(ALIGN(BITS_TO_BYTES(nlk->ngroups), sizeof(u32)), optlen))
 			err = -EFAULT;
 		netlink_unlock_table();
-		break;
+		return err;
 	}
 	case NETLINK_CAP_ACK:
-		if (len < sizeof(int))
-			return -EINVAL;
-		len = sizeof(int);
-		val = nlk->flags & NETLINK_F_CAP_ACK ? 1 : 0;
-		if (put_user(len, optlen) ||
-		    put_user(val, optval))
-			return -EFAULT;
-		err = 0;
+		flag = NETLINK_F_CAP_ACK;
 		break;
 	case NETLINK_EXT_ACK:
-		if (len < sizeof(int))
-			return -EINVAL;
-		len = sizeof(int);
-		val = nlk->flags & NETLINK_F_EXT_ACK ? 1 : 0;
-		if (put_user(len, optlen) || put_user(val, optval))
-			return -EFAULT;
-		err = 0;
+		flag = NETLINK_F_EXT_ACK;
 		break;
 	case NETLINK_GET_STRICT_CHK:
-		if (len < sizeof(int))
-			return -EINVAL;
-		len = sizeof(int);
-		val = nlk->flags & NETLINK_F_STRICT_CHK ? 1 : 0;
-		if (put_user(len, optlen) || put_user(val, optval))
-			return -EFAULT;
-		err = 0;
+		flag = NETLINK_F_STRICT_CHK;
 		break;
 	default:
-		err = -ENOPROTOOPT;
+		return -ENOPROTOOPT;
 	}
-	return err;
+
+	if (len < sizeof(int))
+		return -EINVAL;
+
+	len = sizeof(int);
+	val = nlk->flags & flag ? 1 : 0;
+
+	if (put_user(len, optlen) ||
+	    copy_to_user(optval, &val, len))
+		return -EFAULT;
+
+	return 0;
 }
 
 static void netlink_cmsg_recv_pktinfo(struct msghdr *msg, struct sk_buff *skb)
@@ -1871,6 +1835,11 @@
 	if (msg->msg_flags & MSG_OOB)
 		return -EOPNOTSUPP;
 
+	if (len == 0) {
+		pr_warn_once("Zero length message leads to an empty skb\n");
+		return -ENODATA;
+	}
+
 	err = scm_send(sock, msg, &scm, true);
 	if (err < 0)
 		return err;
@@ -1889,8 +1858,9 @@
 			goto out;
 		netlink_skb_flags |= NETLINK_SKB_DST;
 	} else {
-		dst_portid = nlk->dst_portid;
-		dst_group = nlk->dst_group;
+		/* Paired with WRITE_ONCE() in netlink_connect() */
+		dst_portid = READ_ONCE(nlk->dst_portid);
+		dst_group = READ_ONCE(nlk->dst_group);
 	}
 
 	/* Paired with WRITE_ONCE() in netlink_insert() */
@@ -1946,7 +1916,7 @@
 	struct sock *sk = sock->sk;
 	struct netlink_sock *nlk = nlk_sk(sk);
 	int noblock = flags & MSG_DONTWAIT;
-	size_t copied;
+	size_t copied, max_recvmsg_len;
 	struct sk_buff *skb, *data_skb;
 	int err, ret;
 
@@ -1979,9 +1949,10 @@
 #endif
 
 	/* Record the max length of recvmsg() calls for future allocations */
-	nlk->max_recvmsg_len = max(nlk->max_recvmsg_len, len);
-	nlk->max_recvmsg_len = min_t(size_t, nlk->max_recvmsg_len,
-				     SKB_WITH_OVERHEAD(32768));
+	max_recvmsg_len = max(READ_ONCE(nlk->max_recvmsg_len), len);
+	max_recvmsg_len = min_t(size_t, max_recvmsg_len,
+				SKB_WITH_OVERHEAD(32768));
+	WRITE_ONCE(nlk->max_recvmsg_len, max_recvmsg_len);
 
 	copied = data_skb->len;
 	if (len < copied) {
@@ -1989,7 +1960,6 @@
 		copied = len;
 	}
 
-	skb_reset_transport_header(data_skb);
 	err = skb_copy_datagram_msg(data_skb, 0, msg, copied);
 
 	if (msg->msg_name) {
@@ -2013,11 +1983,11 @@
 
 	skb_free_datagram(sk, skb);
 
-	if (nlk->cb_running &&
+	if (READ_ONCE(nlk->cb_running) &&
 	    atomic_read(&sk->sk_rmem_alloc) <= sk->sk_rcvbuf / 2) {
-		ret = netlink_dump(sk);
+		ret = netlink_dump(sk, false);
 		if (ret) {
-			sk->sk_err = -ret;
+			WRITE_ONCE(sk->sk_err, -ret);
 			sk_error_report(sk);
 		}
 	}
@@ -2174,8 +2144,9 @@
 {
 	struct sock *sk;
 	struct netlink_table *tbl = &nl_table[ksk->sk_protocol];
+	struct hlist_node *tmp;
 
-	sk_for_each_bound(sk, &tbl->mc_list)
+	sk_for_each_bound_safe(sk, tmp, &tbl->mc_list)
 		netlink_update_socket_mc(nlk_sk(sk), group, 0);
 }
 
@@ -2225,18 +2196,20 @@
 	return 0;
 }
 
-static int netlink_dump(struct sock *sk)
+static int netlink_dump(struct sock *sk, bool lock_taken)
 {
 	struct netlink_sock *nlk = nlk_sk(sk);
 	struct netlink_ext_ack extack = {};
 	struct netlink_callback *cb;
 	struct sk_buff *skb = NULL;
+	size_t max_recvmsg_len;
 	struct module *module;
 	int err = -ENOBUFS;
 	int alloc_min_size;
 	int alloc_size;
 
-	mutex_lock(nlk->cb_mutex);
+	if (!lock_taken)
+		mutex_lock(nlk->cb_mutex);
 	if (!nlk->cb_running) {
 		err = -EINVAL;
 		goto errout_skb;
@@ -2253,8 +2226,9 @@
 	cb = &nlk->cb;
 	alloc_min_size = max_t(int, cb->min_dump_alloc, NLMSG_GOODSIZE);
 
-	if (alloc_min_size < nlk->max_recvmsg_len) {
-		alloc_size = nlk->max_recvmsg_len;
+	max_recvmsg_len = READ_ONCE(nlk->max_recvmsg_len);
+	if (alloc_min_size < max_recvmsg_len) {
+		alloc_size = max_recvmsg_len;
 		skb = alloc_skb(alloc_size,
 				(GFP_KERNEL & ~__GFP_DIRECT_RECLAIM) |
 				__GFP_NOWARN | __GFP_NORETRY);
@@ -2277,6 +2251,13 @@
 	 * single netdev. The outcome is MSG_TRUNC error.
 	 */
 	skb_reserve(skb, skb_tailroom(skb) - alloc_size);
+
+	/* Make sure malicious BPF programs can not read unitialized memory
+	 * from skb->head -> skb->data
+	 */
+	skb_reset_network_header(skb);
+	skb_reset_mac_header(skb);
+
 	netlink_skb_set_owner_r(skb, sk);
 
 	if (nlk->dump_done_errno > 0) {
@@ -2318,7 +2299,7 @@
 	if (cb->done)
 		cb->done(cb);
 
-	nlk->cb_running = false;
+	WRITE_ONCE(nlk->cb_running, false);
 	module = cb->module;
 	skb = cb->skb;
 	mutex_unlock(nlk->cb_mutex);
@@ -2381,12 +2362,10 @@
 			goto error_put;
 	}
 
-	nlk->cb_running = true;
+	WRITE_ONCE(nlk->cb_running, true);
 	nlk->dump_done_errno = INT_MAX;
 
-	mutex_unlock(nlk->cb_mutex);
-
-	ret = netlink_dump(sk);
+	ret = netlink_dump(sk, true);
 
 	sock_put(sk);
 
@@ -2444,7 +2423,7 @@
 
 	skb = nlmsg_new(payload + tlvlen, GFP_KERNEL);
 	if (!skb) {
-		NETLINK_CB(in_skb).sk->sk_err = ENOBUFS;
+		WRITE_ONCE(NETLINK_CB(in_skb).sk->sk_err, ENOBUFS);
 		sk_error_report(NETLINK_CB(in_skb).sk);
 		return;
 	}
@@ -2667,7 +2646,7 @@
 			   nlk->groups ? (u32)nlk->groups[0] : 0,
 			   sk_rmem_alloc_get(s),
 			   sk_wmem_alloc_get(s),
-			   nlk->cb_running,
+			   READ_ONCE(nlk->cb_running),
 			   refcount_read(&s->sk_refcnt),
 			   atomic_read(&s->sk_drops),
 			   sock_i_ino(s)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlink/af_netlink.h
+++ linux-xilinx-zynqmp-5.15.0/net/netlink/af_netlink.h
@@ -4,7 +4,6 @@
 
 #include <linux/rhashtable.h>
 #include <linux/atomic.h>
-#include <linux/workqueue.h>
 #include <net/sock.h>
 
 /* flags */
@@ -46,7 +45,6 @@
 
 	struct rhash_head	node;
 	struct rcu_head		rcu;
-	struct work_struct	work;
 };
 
 static inline struct netlink_sock *nlk_sk(struct sock *sk)
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlink/diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlink/diag.c
@@ -94,6 +94,7 @@
 	struct net *net = sock_net(skb->sk);
 	struct netlink_diag_req *req;
 	struct netlink_sock *nlsk;
+	unsigned long flags;
 	struct sock *sk;
 	int num = 2;
 	int ret = 0;
@@ -152,7 +153,7 @@
 	num++;
 
 mc_list:
-	read_lock(&nl_table_lock);
+	read_lock_irqsave(&nl_table_lock, flags);
 	sk_for_each_bound(sk, &tbl->mc_list) {
 		if (sk_hashed(sk))
 			continue;
@@ -167,13 +168,13 @@
 				 NETLINK_CB(cb->skb).portid,
 				 cb->nlh->nlmsg_seq,
 				 NLM_F_MULTI,
-				 sock_i_ino(sk)) < 0) {
+				 __sock_i_ino(sk)) < 0) {
 			ret = 1;
 			break;
 		}
 		num++;
 	}
-	read_unlock(&nl_table_lock);
+	read_unlock_irqrestore(&nl_table_lock, flags);
 
 done:
 	cb->args[0] = num;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlink/genetlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlink/genetlink.c
@@ -1089,15 +1089,11 @@
 	if (IS_ERR(msg))
 		return PTR_ERR(msg);
 
-	if (!family->netnsok) {
+	if (!family->netnsok)
 		genlmsg_multicast_netns(&genl_ctrl, &init_net, msg, 0,
 					0, GFP_KERNEL);
-	} else {
-		rcu_read_lock();
-		genlmsg_multicast_allns(&genl_ctrl, msg, 0,
-					0, GFP_ATOMIC);
-		rcu_read_unlock();
-	}
+	else
+		genlmsg_multicast_allns(&genl_ctrl, msg, 0, 0);
 
 	return 0;
 }
@@ -1174,13 +1170,17 @@
 							     op.policy,
 							     op.maxattr);
 			if (err)
-				return err;
+				goto err_free_state;
 		}
 	}
 
 	if (!ctx->state)
 		return -ENODATA;
 	return 0;
+
+err_free_state:
+	netlink_policy_dump_free(ctx->state);
+	return err;
 }
 
 static void *ctrl_dumppolicy_prep(struct sk_buff *skb,
@@ -1375,6 +1375,9 @@
 		if ((grp->flags & GENL_UNS_ADMIN_PERM) &&
 		    !ns_capable(net->user_ns, CAP_NET_ADMIN))
 			ret = -EPERM;
+		if (grp->cap_sys_admin &&
+		    !ns_capable(net->user_ns, CAP_SYS_ADMIN))
+			ret = -EPERM;
 
 		break;
 	}
@@ -1434,23 +1437,23 @@
 
 core_initcall(genl_init);
 
-static int genlmsg_mcast(struct sk_buff *skb, u32 portid, unsigned long group,
-			 gfp_t flags)
+static int genlmsg_mcast(struct sk_buff *skb, u32 portid, unsigned long group)
 {
 	struct sk_buff *tmp;
 	struct net *net, *prev = NULL;
 	bool delivered = false;
 	int err;
 
+	rcu_read_lock();
 	for_each_net_rcu(net) {
 		if (prev) {
-			tmp = skb_clone(skb, flags);
+			tmp = skb_clone(skb, GFP_ATOMIC);
 			if (!tmp) {
 				err = -ENOMEM;
 				goto error;
 			}
 			err = nlmsg_multicast(prev->genl_sock, tmp,
-					      portid, group, flags);
+					      portid, group, GFP_ATOMIC);
 			if (!err)
 				delivered = true;
 			else if (err != -ESRCH)
@@ -1459,27 +1462,31 @@
 
 		prev = net;
 	}
+	err = nlmsg_multicast(prev->genl_sock, skb, portid, group, GFP_ATOMIC);
+
+	rcu_read_unlock();
 
-	err = nlmsg_multicast(prev->genl_sock, skb, portid, group, flags);
 	if (!err)
 		delivered = true;
 	else if (err != -ESRCH)
 		return err;
 	return delivered ? 0 : -ESRCH;
  error:
+	rcu_read_unlock();
+
 	kfree_skb(skb);
 	return err;
 }
 
 int genlmsg_multicast_allns(const struct genl_family *family,
 			    struct sk_buff *skb, u32 portid,
-			    unsigned int group, gfp_t flags)
+			    unsigned int group)
 {
 	if (WARN_ON_ONCE(group >= family->n_mcgrps))
 		return -EINVAL;
 
 	group = family->mcgrp_offset + group;
-	return genlmsg_mcast(skb, portid, group, flags);
+	return genlmsg_mcast(skb, portid, group);
 }
 EXPORT_SYMBOL(genlmsg_multicast_allns);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netlink/policy.c
+++ linux-xilinx-zynqmp-5.15.0/net/netlink/policy.c
@@ -144,7 +144,7 @@
 
 	err = add_policy(&state, policy, maxtype);
 	if (err)
-		return err;
+		goto err_try_undo;
 
 	for (policy_idx = 0;
 	     policy_idx < state->n_alloc && state->policies[policy_idx].policy;
@@ -164,7 +164,7 @@
 						 policy[type].nested_policy,
 						 policy[type].len);
 				if (err)
-					return err;
+					goto err_try_undo;
 				break;
 			default:
 				break;
@@ -174,6 +174,16 @@
 
 	*pstate = state;
 	return 0;
+
+err_try_undo:
+	/* Try to preserve reasonable unwind semantics - if we're starting from
+	 * scratch clean up fully, otherwise record what we got and caller will.
+	 */
+	if (!*pstate)
+		netlink_policy_dump_free(state);
+	else
+		*pstate = state;
+	return err;
 }
 
 static bool
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/af_netrom.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/af_netrom.c
@@ -298,7 +298,7 @@
 {
 	struct sock *sk = sock->sk;
 	struct nr_sock *nr = nr_sk(sk);
-	unsigned long opt;
+	unsigned int opt;
 
 	if (level != SOL_NETROM)
 		return -ENOPROTOOPT;
@@ -306,18 +306,18 @@
 	if (optlen < sizeof(unsigned int))
 		return -EINVAL;
 
-	if (copy_from_sockptr(&opt, optval, sizeof(unsigned int)))
+	if (copy_from_sockptr(&opt, optval, sizeof(opt)))
 		return -EFAULT;
 
 	switch (optname) {
 	case NETROM_T1:
-		if (opt < 1 || opt > ULONG_MAX / HZ)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		nr->t1 = opt * HZ;
 		return 0;
 
 	case NETROM_T2:
-		if (opt < 1 || opt > ULONG_MAX / HZ)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		nr->t2 = opt * HZ;
 		return 0;
@@ -329,13 +329,13 @@
 		return 0;
 
 	case NETROM_T4:
-		if (opt < 1 || opt > ULONG_MAX / HZ)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		nr->t4 = opt * HZ;
 		return 0;
 
 	case NETROM_IDLE:
-		if (opt > ULONG_MAX / (60 * HZ))
+		if (opt > UINT_MAX / (60 * HZ))
 			return -EINVAL;
 		nr->idle = opt * 60 * HZ;
 		return 0;
@@ -400,6 +400,11 @@
 	struct sock *sk = sock->sk;
 
 	lock_sock(sk);
+	if (sock->state != SS_UNCONNECTED) {
+		release_sock(sk);
+		return -EINVAL;
+	}
+
 	if (sk->sk_state != TCP_LISTEN) {
 		memset(&nr_sk(sk)->user_addr, 0, AX25_ADDR_LEN);
 		sk->sk_max_ack_backlog = backlog;
@@ -448,16 +453,16 @@
 	nr_init_timers(sk);
 
 	nr->t1     =
-		msecs_to_jiffies(sysctl_netrom_transport_timeout);
+		msecs_to_jiffies(READ_ONCE(sysctl_netrom_transport_timeout));
 	nr->t2     =
-		msecs_to_jiffies(sysctl_netrom_transport_acknowledge_delay);
+		msecs_to_jiffies(READ_ONCE(sysctl_netrom_transport_acknowledge_delay));
 	nr->n2     =
-		msecs_to_jiffies(sysctl_netrom_transport_maximum_tries);
+		msecs_to_jiffies(READ_ONCE(sysctl_netrom_transport_maximum_tries));
 	nr->t4     =
-		msecs_to_jiffies(sysctl_netrom_transport_busy_delay);
+		msecs_to_jiffies(READ_ONCE(sysctl_netrom_transport_busy_delay));
 	nr->idle   =
-		msecs_to_jiffies(sysctl_netrom_transport_no_activity_timeout);
-	nr->window = sysctl_netrom_transport_requested_window_size;
+		msecs_to_jiffies(READ_ONCE(sysctl_netrom_transport_no_activity_timeout));
+	nr->window = READ_ONCE(sysctl_netrom_transport_requested_window_size);
 
 	nr->bpqext = 1;
 	nr->state  = NR_STATE_0;
@@ -655,6 +660,11 @@
 		goto out_release;
 	}
 
+	if (sock->state == SS_CONNECTING) {
+		err = -EALREADY;
+		goto out_release;
+	}
+
 	sk->sk_state   = TCP_CLOSE;
 	sock->state = SS_UNCONNECTED;
 
@@ -944,7 +954,7 @@
 		 * G8PZT's Xrouter which is sending packets with command type 7
 		 * as an extension of the protocol.
 		 */
-		if (sysctl_netrom_reset_circuit &&
+		if (READ_ONCE(sysctl_netrom_reset_circuit) &&
 		    (frametype != NR_RESET || flags != 0))
 			nr_transmit_reset(skb, 1);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/nr_dev.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/nr_dev.c
@@ -81,7 +81,7 @@
 	buff[6] |= AX25_SSSID_SPARE;
 	buff    += AX25_ADDR_LEN;
 
-	*buff++ = sysctl_netrom_network_ttl_initialiser;
+	*buff++ = READ_ONCE(sysctl_netrom_network_ttl_initialiser);
 
 	*buff++ = NR_PROTO_IP;
 	*buff++ = NR_PROTO_IP;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/nr_in.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/nr_in.c
@@ -97,7 +97,7 @@
 		break;
 
 	case NR_RESET:
-		if (sysctl_netrom_reset_circuit)
+		if (READ_ONCE(sysctl_netrom_reset_circuit))
 			nr_disconnect(sk, ECONNRESET);
 		break;
 
@@ -128,7 +128,7 @@
 		break;
 
 	case NR_RESET:
-		if (sysctl_netrom_reset_circuit)
+		if (READ_ONCE(sysctl_netrom_reset_circuit))
 			nr_disconnect(sk, ECONNRESET);
 		break;
 
@@ -262,7 +262,7 @@
 		break;
 
 	case NR_RESET:
-		if (sysctl_netrom_reset_circuit)
+		if (READ_ONCE(sysctl_netrom_reset_circuit))
 			nr_disconnect(sk, ECONNRESET);
 		break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/nr_out.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/nr_out.c
@@ -204,7 +204,7 @@
 	dptr[6] |= AX25_SSSID_SPARE;
 	dptr += AX25_ADDR_LEN;
 
-	*dptr++ = sysctl_netrom_network_ttl_initialiser;
+	*dptr++ = READ_ONCE(sysctl_netrom_network_ttl_initialiser);
 
 	if (!nr_route_frame(skb, NULL)) {
 		kfree_skb(skb);
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/nr_route.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/nr_route.c
@@ -153,7 +153,7 @@
 		nr_neigh->digipeat = NULL;
 		nr_neigh->ax25     = NULL;
 		nr_neigh->dev      = dev;
-		nr_neigh->quality  = sysctl_netrom_default_path_quality;
+		nr_neigh->quality  = READ_ONCE(sysctl_netrom_default_path_quality);
 		nr_neigh->locked   = 0;
 		nr_neigh->count    = 0;
 		nr_neigh->number   = nr_neigh_no++;
@@ -285,22 +285,14 @@
 	return 0;
 }
 
-static inline void __nr_remove_node(struct nr_node *nr_node)
+static void nr_remove_node_locked(struct nr_node *nr_node)
 {
+	lockdep_assert_held(&nr_node_list_lock);
+
 	hlist_del_init(&nr_node->node_node);
 	nr_node_put(nr_node);
 }
 
-#define nr_remove_node_locked(__node) \
-	__nr_remove_node(__node)
-
-static void nr_remove_node(struct nr_node *nr_node)
-{
-	spin_lock_bh(&nr_node_list_lock);
-	__nr_remove_node(nr_node);
-	spin_unlock_bh(&nr_node_list_lock);
-}
-
 static inline void __nr_remove_neigh(struct nr_neigh *nr_neigh)
 {
 	hlist_del_init(&nr_neigh->neigh_node);
@@ -339,6 +331,7 @@
 		return -EINVAL;
 	}
 
+	spin_lock_bh(&nr_node_list_lock);
 	nr_node_lock(nr_node);
 	for (i = 0; i < nr_node->count; i++) {
 		if (nr_node->routes[i].neighbour == nr_neigh) {
@@ -352,7 +345,7 @@
 			nr_node->count--;
 
 			if (nr_node->count == 0) {
-				nr_remove_node(nr_node);
+				nr_remove_node_locked(nr_node);
 			} else {
 				switch (i) {
 				case 0:
@@ -367,12 +360,14 @@
 				nr_node_put(nr_node);
 			}
 			nr_node_unlock(nr_node);
+			spin_unlock_bh(&nr_node_list_lock);
 
 			return 0;
 		}
 	}
 	nr_neigh_put(nr_neigh);
 	nr_node_unlock(nr_node);
+	spin_unlock_bh(&nr_node_list_lock);
 	nr_node_put(nr_node);
 
 	return -EINVAL;
@@ -728,7 +723,7 @@
 	nr_neigh->ax25 = NULL;
 	ax25_cb_put(ax25);
 
-	if (++nr_neigh->failed < sysctl_netrom_link_fails_count) {
+	if (++nr_neigh->failed < READ_ONCE(sysctl_netrom_link_fails_count)) {
 		nr_neigh_put(nr_neigh);
 		return;
 	}
@@ -759,6 +754,12 @@
 	int ret;
 	struct sk_buff *skbn;
 
+	/*
+	 * Reject malformed packets early. Check that it contains at least 2
+	 * addresses and 1 byte more for Time-To-Live
+	 */
+	if (skb->len < 2 * sizeof(ax25_address) + 1)
+		return 0;
 
 	nr_src  = (ax25_address *)(skb->data + 0);
 	nr_dest = (ax25_address *)(skb->data + 7);
@@ -766,7 +767,7 @@
 	if (ax25 != NULL) {
 		ret = nr_add_node(nr_src, "", &ax25->dest_addr, ax25->digipeat,
 				  ax25->ax25_dev->dev, 0,
-				  sysctl_netrom_obsolescence_count_initialiser);
+				  READ_ONCE(sysctl_netrom_obsolescence_count_initialiser));
 		if (ret)
 			return ret;
 	}
@@ -780,7 +781,7 @@
 		return ret;
 	}
 
-	if (!sysctl_netrom_routing_control && ax25 != NULL)
+	if (!READ_ONCE(sysctl_netrom_routing_control) && ax25 != NULL)
 		return 0;
 
 	/* Its Time-To-Live has expired */
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/nr_subr.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/nr_subr.c
@@ -123,7 +123,7 @@
 	unsigned char  *dptr;
 	int len, timeout;
 
-	len = NR_NETWORK_LEN + NR_TRANSPORT_LEN;
+	len = NR_TRANSPORT_LEN;
 
 	switch (frametype & 0x0F) {
 	case NR_CONNREQ:
@@ -141,7 +141,8 @@
 		return;
 	}
 
-	if ((skb = alloc_skb(len, GFP_ATOMIC)) == NULL)
+	skb = alloc_skb(NR_NETWORK_LEN + len, GFP_ATOMIC);
+	if (!skb)
 		return;
 
 	/*
@@ -149,7 +150,7 @@
 	 */
 	skb_reserve(skb, NR_NETWORK_LEN);
 
-	dptr = skb_put(skb, skb_tailroom(skb));
+	dptr = skb_put(skb, len);
 
 	switch (frametype & 0x0F) {
 	case NR_CONNREQ:
@@ -181,7 +182,8 @@
 		*dptr++ = nr->my_id;
 		*dptr++ = frametype;
 		*dptr++ = nr->window;
-		if (nr->bpqext) *dptr++ = sysctl_netrom_network_ttl_initialiser;
+		if (nr->bpqext)
+			*dptr++ = READ_ONCE(sysctl_netrom_network_ttl_initialiser);
 		break;
 
 	case NR_DISCREQ:
@@ -235,7 +237,7 @@
 	dptr[6] |= AX25_SSSID_SPARE;
 	dptr += AX25_ADDR_LEN;
 
-	*dptr++ = sysctl_netrom_network_ttl_initialiser;
+	*dptr++ = READ_ONCE(sysctl_netrom_network_ttl_initialiser);
 
 	if (mine) {
 		*dptr++ = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/netrom/nr_timer.c
+++ linux-xilinx-zynqmp-5.15.0/net/netrom/nr_timer.c
@@ -121,6 +121,8 @@
 		   is accepted() it isn't 'dead' so doesn't get removed. */
 		if (sock_flag(sk, SOCK_DESTROY) ||
 		    (sk->sk_state == TCP_LISTEN && sock_flag(sk, SOCK_DEAD))) {
+			if (sk->sk_state == TCP_LISTEN)
+				sock_hold(sk);
 			bh_unlock_sock(sk);
 			nr_destroy_socket(sk);
 			goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/core.c
@@ -38,7 +38,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -94,13 +94,13 @@
 
 	device_lock(&dev->dev);
 
-	if (dev->rfkill && rfkill_blocked(dev->rfkill)) {
-		rc = -ERFKILL;
+	if (dev->shutting_down) {
+		rc = -ENODEV;
 		goto error;
 	}
 
-	if (!device_is_registered(&dev->dev)) {
-		rc = -ENODEV;
+	if (dev->rfkill && rfkill_blocked(dev->rfkill)) {
+		rc = -ERFKILL;
 		goto error;
 	}
 
@@ -142,7 +142,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -207,7 +207,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -246,7 +246,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -291,7 +291,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -335,7 +335,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -401,7 +401,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -448,7 +448,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -495,7 +495,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		kfree_skb(skb);
 		goto error;
@@ -552,7 +552,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -601,7 +601,7 @@
 
 	device_lock(&dev->dev);
 
-	if (!device_is_registered(&dev->dev)) {
+	if (dev->shutting_down) {
 		rc = -ENODEV;
 		goto error;
 	}
@@ -1125,11 +1125,7 @@
 	if (rc)
 		pr_err("Could not register llcp device\n");
 
-	rc = nfc_genl_device_added(dev);
-	if (rc)
-		pr_debug("The userspace won't be notified that the device %s was added\n",
-			 dev_name(&dev->dev));
-
+	device_lock(&dev->dev);
 	dev->rfkill = rfkill_alloc(dev_name(&dev->dev), &dev->dev,
 				   RFKILL_TYPE_NFC, &nfc_rfkill_ops, dev);
 	if (dev->rfkill) {
@@ -1138,6 +1134,13 @@
 			dev->rfkill = NULL;
 		}
 	}
+	dev->shutting_down = false;
+	device_unlock(&dev->dev);
+
+	rc = nfc_genl_device_added(dev);
+	if (rc)
+		pr_debug("The userspace won't be notified that the device %s was added\n",
+			 dev_name(&dev->dev));
 
 	return 0;
 }
@@ -1154,24 +1157,25 @@
 
 	pr_debug("dev_name=%s\n", dev_name(&dev->dev));
 
+	rc = nfc_genl_device_removed(dev);
+	if (rc)
+		pr_debug("The userspace won't be notified that the device %s "
+			 "was removed\n", dev_name(&dev->dev));
+
+	device_lock(&dev->dev);
 	if (dev->rfkill) {
 		rfkill_unregister(dev->rfkill);
 		rfkill_destroy(dev->rfkill);
+		dev->rfkill = NULL;
 	}
+	dev->shutting_down = true;
+	device_unlock(&dev->dev);
 
 	if (dev->ops->check_presence) {
-		device_lock(&dev->dev);
-		dev->shutting_down = true;
-		device_unlock(&dev->dev);
 		del_timer_sync(&dev->check_pres_timer);
 		cancel_work_sync(&dev->check_pres_work);
 	}
 
-	rc = nfc_genl_device_removed(dev);
-	if (rc)
-		pr_debug("The userspace won't be notified that the device %s "
-			 "was removed\n", dev_name(&dev->dev));
-
 	nfc_llcp_unregister_device(dev);
 
 	mutex_lock(&nfc_devlist_mutex);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/llcp.h
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/llcp.h
@@ -202,7 +202,6 @@
 void nfc_llcp_sock_unlink(struct llcp_sock_list *l, struct sock *s);
 void nfc_llcp_socket_remote_param_init(struct nfc_llcp_sock *sock);
 struct nfc_llcp_local *nfc_llcp_find_local(struct nfc_dev *dev);
-struct nfc_llcp_local *nfc_llcp_local_get(struct nfc_llcp_local *local);
 int nfc_llcp_local_put(struct nfc_llcp_local *local);
 u8 nfc_llcp_get_sdp_ssap(struct nfc_llcp_local *local,
 			 struct nfc_llcp_sock *sock);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/llcp_commands.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/llcp_commands.c
@@ -361,6 +361,7 @@
 	struct sk_buff *skb;
 	struct nfc_llcp_local *local;
 	u16 size = 0;
+	int err;
 
 	pr_debug("Sending SYMM\n");
 
@@ -372,8 +373,10 @@
 	size += dev->tx_headroom + dev->tx_tailroom + NFC_HEADER_SIZE;
 
 	skb = alloc_skb(size, GFP_KERNEL);
-	if (skb == NULL)
-		return -ENOMEM;
+	if (skb == NULL) {
+		err = -ENOMEM;
+		goto out;
+	}
 
 	skb_reserve(skb, dev->tx_headroom + NFC_HEADER_SIZE);
 
@@ -383,8 +386,11 @@
 
 	nfc_llcp_send_to_raw_sock(local, skb, NFC_DIRECTION_TX);
 
-	return nfc_data_exchange(dev, local->target_idx, skb,
+	err = nfc_data_exchange(dev, local->target_idx, skb,
 				 nfc_llcp_recv, local);
+out:
+	nfc_llcp_local_put(local);
+	return err;
 }
 
 int nfc_llcp_send_connect(struct nfc_llcp_sock *sock)
@@ -394,7 +400,8 @@
 	const u8 *service_name_tlv = NULL;
 	const u8 *miux_tlv = NULL;
 	const u8 *rw_tlv = NULL;
-	u8 service_name_tlv_length, miux_tlv_length,  rw_tlv_length, rw;
+	u8 service_name_tlv_length = 0;
+	u8 miux_tlv_length,  rw_tlv_length, rw;
 	int err;
 	u16 size = 0;
 	__be16 miux;
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/llcp_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/llcp_core.c
@@ -17,6 +17,8 @@
 static u8 llcp_magic[3] = {0x46, 0x66, 0x6d};
 
 static LIST_HEAD(llcp_devices);
+/* Protects llcp_devices list */
+static DEFINE_SPINLOCK(llcp_devices_lock);
 
 static void nfc_llcp_rx_skb(struct nfc_llcp_local *local, struct sk_buff *skb);
 
@@ -143,8 +145,15 @@
 	write_unlock(&local->raw_sockets.lock);
 }
 
-struct nfc_llcp_local *nfc_llcp_local_get(struct nfc_llcp_local *local)
+static struct nfc_llcp_local *nfc_llcp_local_get(struct nfc_llcp_local *local)
 {
+	/* Since using nfc_llcp_local may result in usage of nfc_dev, whenever
+	 * we hold a reference to local, we also need to hold a reference to
+	 * the device to avoid UAF.
+	 */
+	if (!nfc_get_device(local->dev->idx))
+		return NULL;
+
 	kref_get(&local->ref);
 
 	return local;
@@ -159,6 +168,7 @@
 	cancel_work_sync(&local->rx_work);
 	cancel_work_sync(&local->timeout_work);
 	kfree_skb(local->rx_pending);
+	local->rx_pending = NULL;
 	del_timer_sync(&local->sdreq_timer);
 	cancel_work_sync(&local->sdreq_timeout_work);
 	nfc_llcp_free_sdp_tlv_list(&local->pending_sdreqs);
@@ -170,17 +180,24 @@
 
 	local = container_of(ref, struct nfc_llcp_local, ref);
 
-	list_del(&local->list);
 	local_cleanup(local);
 	kfree(local);
 }
 
 int nfc_llcp_local_put(struct nfc_llcp_local *local)
 {
+	struct nfc_dev *dev;
+	int ret;
+
 	if (local == NULL)
 		return 0;
 
-	return kref_put(&local->ref, local_release);
+	dev = local->dev;
+
+	ret = kref_put(&local->ref, local_release);
+	nfc_put_device(dev);
+
+	return ret;
 }
 
 static struct nfc_llcp_sock *nfc_llcp_sock_get(struct nfc_llcp_local *local,
@@ -203,17 +220,13 @@
 
 		if (tmp_sock->ssap == ssap && tmp_sock->dsap == dsap) {
 			llcp_sock = tmp_sock;
+			sock_hold(&llcp_sock->sk);
 			break;
 		}
 	}
 
 	read_unlock(&local->sockets.lock);
 
-	if (llcp_sock == NULL)
-		return NULL;
-
-	sock_hold(&llcp_sock->sk);
-
 	return llcp_sock;
 }
 
@@ -283,12 +296,33 @@
 struct nfc_llcp_local *nfc_llcp_find_local(struct nfc_dev *dev)
 {
 	struct nfc_llcp_local *local;
+	struct nfc_llcp_local *res = NULL;
 
+	spin_lock(&llcp_devices_lock);
 	list_for_each_entry(local, &llcp_devices, list)
-		if (local->dev == dev)
+		if (local->dev == dev) {
+			res = nfc_llcp_local_get(local);
+			break;
+		}
+	spin_unlock(&llcp_devices_lock);
+
+	return res;
+}
+
+static struct nfc_llcp_local *nfc_llcp_remove_local(struct nfc_dev *dev)
+{
+	struct nfc_llcp_local *local, *tmp;
+
+	spin_lock(&llcp_devices_lock);
+	list_for_each_entry_safe(local, tmp, &llcp_devices, list)
+		if (local->dev == dev) {
+			list_del(&local->list);
+			spin_unlock(&llcp_devices_lock);
 			return local;
+		}
+	spin_unlock(&llcp_devices_lock);
 
-	pr_debug("No device found\n");
+	pr_warn("Shutting down device not found\n");
 
 	return NULL;
 }
@@ -325,7 +359,8 @@
 
 static
 struct nfc_llcp_sock *nfc_llcp_sock_from_sn(struct nfc_llcp_local *local,
-					    const u8 *sn, size_t sn_len)
+					    const u8 *sn, size_t sn_len,
+					    bool needref)
 {
 	struct sock *sk;
 	struct nfc_llcp_sock *llcp_sock, *tmp_sock;
@@ -361,6 +396,8 @@
 
 		if (memcmp(sn, tmp_sock->service_name, sn_len) == 0) {
 			llcp_sock = tmp_sock;
+			if (needref)
+				sock_hold(&llcp_sock->sk);
 			break;
 		}
 	}
@@ -402,7 +439,8 @@
 		 * to this service name.
 		 */
 		if (nfc_llcp_sock_from_sn(local, sock->service_name,
-					  sock->service_name_len) != NULL) {
+					  sock->service_name_len,
+					  false) != NULL) {
 			mutex_unlock(&local->sdp_lock);
 
 			return LLCP_SAP_MAX;
@@ -609,12 +647,15 @@
 
 	*general_bytes_len = local->gb_len;
 
+	nfc_llcp_local_put(local);
+
 	return local->gb;
 }
 
 int nfc_llcp_set_remote_gb(struct nfc_dev *dev, const u8 *gb, u8 gb_len)
 {
 	struct nfc_llcp_local *local;
+	int err;
 
 	if (gb_len < 3 || gb_len > NFC_MAX_GT_LEN)
 		return -EINVAL;
@@ -631,12 +672,16 @@
 
 	if (memcmp(local->remote_gb, llcp_magic, 3)) {
 		pr_err("MAC does not support LLCP\n");
-		return -EINVAL;
+		err = -EINVAL;
+		goto out;
 	}
 
-	return nfc_llcp_parse_gb_tlv(local,
+	err = nfc_llcp_parse_gb_tlv(local,
 				     &local->remote_gb[3],
 				     local->remote_gb_len - 3);
+out:
+	nfc_llcp_local_put(local);
+	return err;
 }
 
 static u8 nfc_llcp_dsap(const struct sk_buff *pdu)
@@ -803,16 +848,7 @@
 static struct nfc_llcp_sock *nfc_llcp_sock_get_sn(struct nfc_llcp_local *local,
 						  const u8 *sn, size_t sn_len)
 {
-	struct nfc_llcp_sock *llcp_sock;
-
-	llcp_sock = nfc_llcp_sock_from_sn(local, sn, sn_len);
-
-	if (llcp_sock == NULL)
-		return NULL;
-
-	sock_hold(&llcp_sock->sk);
-
-	return llcp_sock;
+	return nfc_llcp_sock_from_sn(local, sn, sn_len, true);
 }
 
 static const u8 *nfc_llcp_connect_sn(const struct sk_buff *skb, size_t *sn_len)
@@ -947,8 +983,17 @@
 	}
 
 	new_sock = nfc_llcp_sock(new_sk);
-	new_sock->dev = local->dev;
+
 	new_sock->local = nfc_llcp_local_get(local);
+	if (!new_sock->local) {
+		reason = LLCP_DM_REJ;
+		sock_put(&new_sock->sk);
+		release_sock(&sock->sk);
+		sock_put(&sock->sk);
+		goto fail;
+	}
+
+	new_sock->dev = local->dev;
 	new_sock->rw = sock->rw;
 	new_sock->miux = sock->miux;
 	new_sock->nfc_protocol = sock->nfc_protocol;
@@ -1277,7 +1322,8 @@
 			}
 
 			llcp_sock = nfc_llcp_sock_from_sn(local, service_name,
-							  service_name_len);
+							  service_name_len,
+							  true);
 			if (!llcp_sock) {
 				sap = 0;
 				goto add_snl;
@@ -1297,6 +1343,7 @@
 
 				if (sap == LLCP_SAP_MAX) {
 					sap = 0;
+					nfc_llcp_sock_put(llcp_sock);
 					goto add_snl;
 				}
 
@@ -1314,6 +1361,7 @@
 
 			pr_debug("%p %d\n", llcp_sock, sap);
 
+			nfc_llcp_sock_put(llcp_sock);
 add_snl:
 			sdp = nfc_llcp_build_sdres_tlv(tid, sap);
 			if (sdp == NULL)
@@ -1526,6 +1574,8 @@
 
 	__nfc_llcp_recv(local, skb);
 
+	nfc_llcp_local_put(local);
+
 	return 0;
 }
 
@@ -1542,6 +1592,8 @@
 
 	/* Close and purge all existing sockets */
 	nfc_llcp_socket_release(local, true, 0);
+
+	nfc_llcp_local_put(local);
 }
 
 void nfc_llcp_mac_is_up(struct nfc_dev *dev, u32 target_idx,
@@ -1567,6 +1619,8 @@
 		mod_timer(&local->link_timer,
 			  jiffies + msecs_to_jiffies(local->remote_lto));
 	}
+
+	nfc_llcp_local_put(local);
 }
 
 int nfc_llcp_register_device(struct nfc_dev *ndev)
@@ -1577,7 +1631,16 @@
 	if (local == NULL)
 		return -ENOMEM;
 
-	local->dev = ndev;
+	/* As we are going to initialize local's refcount, we need to get the
+	 * nfc_dev to avoid UAF, otherwise there is no point in continuing.
+	 * See nfc_llcp_local_get().
+	 */
+	local->dev = nfc_get_device(ndev->idx);
+	if (!local->dev) {
+		kfree(local);
+		return -ENODEV;
+	}
+
 	INIT_LIST_HEAD(&local->list);
 	kref_init(&local->ref);
 	mutex_init(&local->sdp_lock);
@@ -1610,14 +1673,16 @@
 	timer_setup(&local->sdreq_timer, nfc_llcp_sdreq_timer, 0);
 	INIT_WORK(&local->sdreq_timeout_work, nfc_llcp_sdreq_timeout_work);
 
+	spin_lock(&llcp_devices_lock);
 	list_add(&local->list, &llcp_devices);
+	spin_unlock(&llcp_devices_lock);
 
 	return 0;
 }
 
 void nfc_llcp_unregister_device(struct nfc_dev *dev)
 {
-	struct nfc_llcp_local *local = nfc_llcp_find_local(dev);
+	struct nfc_llcp_local *local = nfc_llcp_remove_local(dev);
 
 	if (local == NULL) {
 		pr_debug("No such device\n");
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/llcp_sock.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/llcp_sock.c
@@ -99,7 +99,7 @@
 	}
 
 	llcp_sock->dev = dev;
-	llcp_sock->local = nfc_llcp_local_get(local);
+	llcp_sock->local = local;
 	llcp_sock->nfc_protocol = llcp_addr.nfc_protocol;
 	llcp_sock->service_name_len = min_t(unsigned int,
 					    llcp_addr.service_name_len,
@@ -181,7 +181,7 @@
 	}
 
 	llcp_sock->dev = dev;
-	llcp_sock->local = nfc_llcp_local_get(local);
+	llcp_sock->local = local;
 	llcp_sock->nfc_protocol = llcp_addr.nfc_protocol;
 
 	nfc_llcp_sock_link(&local->raw_sockets, sk);
@@ -698,24 +698,22 @@
 	if (dev->dep_link_up == false) {
 		ret = -ENOLINK;
 		device_unlock(&dev->dev);
-		goto put_dev;
+		goto sock_llcp_put_local;
 	}
 	device_unlock(&dev->dev);
 
 	if (local->rf_mode == NFC_RF_INITIATOR &&
 	    addr->target_idx != local->target_idx) {
 		ret = -ENOLINK;
-		goto put_dev;
+		goto sock_llcp_put_local;
 	}
 
 	llcp_sock->dev = dev;
-	llcp_sock->local = nfc_llcp_local_get(local);
+	llcp_sock->local = local;
 	llcp_sock->ssap = nfc_llcp_get_local_ssap(local);
 	if (llcp_sock->ssap == LLCP_SAP_MAX) {
-		nfc_llcp_local_put(llcp_sock->local);
-		llcp_sock->local = NULL;
 		ret = -ENOMEM;
-		goto put_dev;
+		goto sock_llcp_nullify;
 	}
 
 	llcp_sock->reserved_ssap = llcp_sock->ssap;
@@ -760,8 +758,13 @@
 
 sock_llcp_release:
 	nfc_llcp_put_ssap(local, llcp_sock->ssap);
-	nfc_llcp_local_put(llcp_sock->local);
+
+sock_llcp_nullify:
 	llcp_sock->local = NULL;
+	llcp_sock->dev = NULL;
+
+sock_llcp_put_local:
+	nfc_llcp_local_put(local);
 
 put_dev:
 	nfc_put_device(dev);
@@ -789,6 +792,11 @@
 
 	lock_sock(sk);
 
+	if (!llcp_sock->local) {
+		release_sock(sk);
+		return -ENODEV;
+	}
+
 	if (sk->sk_type == SOCK_DGRAM) {
 		DECLARE_SOCKADDR(struct sockaddr_nfc_llcp *, addr,
 				 msg->msg_name);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/nci/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/nci/core.c
@@ -144,12 +144,15 @@
 {
 	int rc;
 
-	if (!test_bit(NCI_UP, &ndev->flags))
-		return -ENETDOWN;
-
 	/* Serialize all requests */
 	mutex_lock(&ndev->req_lock);
-	rc = __nci_request(ndev, req, opt, timeout);
+	/* check the state after obtaing the lock against any races
+	 * from nci_close_device when the device gets removed.
+	 */
+	if (test_bit(NCI_UP, &ndev->flags))
+		rc = __nci_request(ndev, req, opt, timeout);
+	else
+		rc = -ENETDOWN;
 	mutex_unlock(&ndev->req_lock);
 
 	return rc;
@@ -473,6 +476,11 @@
 
 	mutex_lock(&ndev->req_lock);
 
+	if (test_bit(NCI_UNREG, &ndev->flags)) {
+		rc = -ENODEV;
+		goto done;
+	}
+
 	if (test_bit(NCI_UP, &ndev->flags)) {
 		rc = -EALREADY;
 		goto done;
@@ -534,7 +542,7 @@
 		skb_queue_purge(&ndev->tx_q);
 
 		ndev->ops->close(ndev);
-		ndev->flags = 0;
+		ndev->flags &= BIT(NCI_UNREG);
 	}
 
 done:
@@ -545,9 +553,17 @@
 static int nci_close_device(struct nci_dev *ndev)
 {
 	nci_req_cancel(ndev, ENODEV);
+
+	/* This mutex needs to be held as a barrier for
+	 * caller nci_unregister_device
+	 */
 	mutex_lock(&ndev->req_lock);
 
 	if (!test_and_clear_bit(NCI_UP, &ndev->flags)) {
+		/* Need to flush the cmd wq in case
+		 * there is a queued/running cmd_work
+		 */
+		flush_workqueue(ndev->cmd_wq);
 		del_timer_sync(&ndev->cmd_timer);
 		del_timer_sync(&ndev->data_timer);
 		mutex_unlock(&ndev->req_lock);
@@ -582,8 +598,8 @@
 
 	del_timer_sync(&ndev->cmd_timer);
 
-	/* Clear flags */
-	ndev->flags = 0;
+	/* Clear flags except NCI_UNREG */
+	ndev->flags &= BIT(NCI_UNREG);
 
 	mutex_unlock(&ndev->req_lock);
 
@@ -892,6 +908,11 @@
 		return -EINVAL;
 	}
 
+	if (protocol >= NFC_PROTO_MAX) {
+		pr_err("the requested nfc protocol is invalid\n");
+		return -EINVAL;
+	}
+
 	if (!(nci_target->supported_protocols & (1 << protocol))) {
 		pr_err("target does not support the requested protocol 0x%x\n",
 		       protocol);
@@ -1190,6 +1211,10 @@
 {
 	nfc_free_device(ndev->nfc_dev);
 	nci_hci_deallocate(ndev);
+
+	/* drop partial rx data packet if present */
+	if (ndev->rx_data_reassembly)
+		kfree_skb(ndev->rx_data_reassembly);
 	kfree(ndev);
 }
 EXPORT_SYMBOL(nci_free_device);
@@ -1270,6 +1295,12 @@
 {
 	struct nci_conn_info *conn_info, *n;
 
+	/* This set_bit is not protected with specialized barrier,
+	 * However, it is fine because the mutex_lock(&ndev->req_lock);
+	 * in nci_close_device() will help to emit one.
+	 */
+	set_bit(NCI_UNREG, &ndev->flags);
+
 	nci_close_device(ndev);
 
 	destroy_workqueue(ndev->cmd_wq);
@@ -1435,6 +1466,19 @@
 				 ndev->ops->n_core_ops);
 }
 
+static bool nci_valid_size(struct sk_buff *skb)
+{
+	unsigned int hdr_size = NCI_CTRL_HDR_SIZE;
+	BUILD_BUG_ON(NCI_CTRL_HDR_SIZE != NCI_DATA_HDR_SIZE);
+
+	if (skb->len < hdr_size ||
+	    !nci_plen(skb->data) ||
+	    skb->len < hdr_size + nci_plen(skb->data)) {
+		return false;
+	}
+	return true;
+}
+
 /* ---- NCI TX Data worker thread ---- */
 
 static void nci_tx_work(struct work_struct *work)
@@ -1485,6 +1529,11 @@
 		nfc_send_to_raw_sock(ndev->nfc_dev, skb,
 				     RAW_PAYLOAD_NCI, NFC_DIRECTION_RX);
 
+		if (!nci_valid_size(skb)) {
+			kfree_skb(skb);
+			continue;
+		}
+
 		/* Process frame */
 		switch (nci_mt(skb->data)) {
 		case NCI_MT_RSP_PKT:
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/nci/data.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/nci/data.c
@@ -118,7 +118,7 @@
 
 		skb_frag = nci_skb_alloc(ndev,
 					 (NCI_DATA_HDR_SIZE + frag_len),
-					 GFP_KERNEL);
+					 GFP_ATOMIC);
 		if (skb_frag == NULL) {
 			rc = -ENOMEM;
 			goto free_exit;
@@ -279,8 +279,10 @@
 		 nci_plen(skb->data));
 
 	conn_info = nci_get_conn_info_by_conn_id(ndev, nci_conn_id(skb->data));
-	if (!conn_info)
+	if (!conn_info) {
+		kfree_skb(skb);
 		return;
+	}
 
 	/* strip the nci data header */
 	skb_pull(skb, NCI_DATA_HDR_SIZE);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/nci/hci.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/nci/hci.c
@@ -153,7 +153,7 @@
 
 	i = 0;
 	skb = nci_skb_alloc(ndev, conn_info->max_pkt_payload_len +
-			    NCI_DATA_HDR_SIZE, GFP_KERNEL);
+			    NCI_DATA_HDR_SIZE, GFP_ATOMIC);
 	if (!skb)
 		return -ENOMEM;
 
@@ -184,7 +184,7 @@
 		if (i < data_len) {
 			skb = nci_skb_alloc(ndev,
 					    conn_info->max_pkt_payload_len +
-					    NCI_DATA_HDR_SIZE, GFP_KERNEL);
+					    NCI_DATA_HDR_SIZE, GFP_ATOMIC);
 			if (!skb)
 				return -ENOMEM;
 
@@ -542,6 +542,8 @@
 
 	pr_debug("pipe created=%d\n", pipe);
 
+	if (pipe >= NCI_HCI_MAX_PIPES)
+		pipe = NCI_HCI_INVALID_PIPE;
 	return pipe;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/nci/ntf.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/nci/ntf.c
@@ -240,6 +240,8 @@
 		target->sens_res = nfca_poll->sens_res;
 		target->sel_res = nfca_poll->sel_res;
 		target->nfcid1_len = nfca_poll->nfcid1_len;
+		if (target->nfcid1_len > ARRAY_SIZE(target->nfcid1))
+			return -EPROTO;
 		if (target->nfcid1_len > 0) {
 			memcpy(target->nfcid1, nfca_poll->nfcid1,
 			       target->nfcid1_len);
@@ -248,6 +250,8 @@
 		nfcb_poll = (struct rf_tech_specific_params_nfcb_poll *)params;
 
 		target->sensb_res_len = nfcb_poll->sensb_res_len;
+		if (target->sensb_res_len > ARRAY_SIZE(target->sensb_res))
+			return -EPROTO;
 		if (target->sensb_res_len > 0) {
 			memcpy(target->sensb_res, nfcb_poll->sensb_res,
 			       target->sensb_res_len);
@@ -256,6 +260,8 @@
 		nfcf_poll = (struct rf_tech_specific_params_nfcf_poll *)params;
 
 		target->sensf_res_len = nfcf_poll->sensf_res_len;
+		if (target->sensf_res_len > ARRAY_SIZE(target->sensf_res))
+			return -EPROTO;
 		if (target->sensf_res_len > 0) {
 			memcpy(target->sensf_res, nfcf_poll->sensf_res,
 			       target->sensf_res_len);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/nci/spi.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/nci/spi.c
@@ -151,6 +151,8 @@
 	int ret;
 
 	skb = nci_skb_alloc(nspi->ndev, 0, GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
 
 	/* add the NCI SPI header to the start of the buffer */
 	hdr = skb_push(skb, NCI_SPI_HDR_LEN);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/netlink.c
@@ -636,8 +636,10 @@
 {
 	struct class_dev_iter *iter = (struct class_dev_iter *) cb->args[0];
 
-	nfc_device_iter_exit(iter);
-	kfree(iter);
+	if (iter) {
+		nfc_device_iter_exit(iter);
+		kfree(iter);
+	}
 
 	return 0;
 }
@@ -1037,11 +1039,14 @@
 	msg = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_KERNEL);
 	if (!msg) {
 		rc = -ENOMEM;
-		goto exit;
+		goto put_local;
 	}
 
 	rc = nfc_genl_send_params(msg, local, info->snd_portid, info->snd_seq);
 
+put_local:
+	nfc_llcp_local_put(local);
+
 exit:
 	device_unlock(&dev->dev);
 
@@ -1103,7 +1108,7 @@
 	if (info->attrs[NFC_ATTR_LLC_PARAM_LTO]) {
 		if (dev->dep_link_up) {
 			rc = -EINPROGRESS;
-			goto exit;
+			goto put_local;
 		}
 
 		local->lto = nla_get_u8(info->attrs[NFC_ATTR_LLC_PARAM_LTO]);
@@ -1115,6 +1120,9 @@
 	if (info->attrs[NFC_ATTR_LLC_PARAM_MIUX])
 		local->miux = cpu_to_be16(miux);
 
+put_local:
+	nfc_llcp_local_put(local);
+
 exit:
 	device_unlock(&dev->dev);
 
@@ -1170,7 +1178,7 @@
 
 		if (rc != 0) {
 			rc = -EINVAL;
-			goto exit;
+			goto put_local;
 		}
 
 		if (!sdp_attrs[NFC_SDP_ATTR_URI])
@@ -1189,7 +1197,7 @@
 		sdreq = nfc_llcp_build_sdreq_tlv(tid, uri, uri_len);
 		if (sdreq == NULL) {
 			rc = -ENOMEM;
-			goto exit;
+			goto put_local;
 		}
 
 		tlvs_len += sdreq->tlv_len;
@@ -1199,10 +1207,14 @@
 
 	if (hlist_empty(&sdreq_list)) {
 		rc = -EINVAL;
-		goto exit;
+		goto put_local;
 	}
 
 	rc = nfc_llcp_send_snl_sdreq(local, &sdreq_list, tlvs_len);
+
+put_local:
+	nfc_llcp_local_put(local);
+
 exit:
 	device_unlock(&dev->dev);
 
@@ -1242,7 +1254,7 @@
 	struct sk_buff *msg;
 	void *hdr;
 
-	msg = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_KERNEL);
+	msg = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_ATOMIC);
 	if (!msg)
 		return -ENOMEM;
 
@@ -1258,7 +1270,7 @@
 
 	genlmsg_end(msg, hdr);
 
-	genlmsg_multicast(&nfc_genl_family, msg, 0, 0, GFP_KERNEL);
+	genlmsg_multicast(&nfc_genl_family, msg, 0, 0, GFP_ATOMIC);
 
 	return 0;
 
@@ -1392,8 +1404,10 @@
 {
 	struct class_dev_iter *iter = (struct class_dev_iter *) cb->args[0];
 
-	nfc_device_iter_exit(iter);
-	kfree(iter);
+	if (iter) {
+		nfc_device_iter_exit(iter);
+		kfree(iter);
+	}
 
 	return 0;
 }
@@ -1438,8 +1452,12 @@
 	rc = dev->ops->se_io(dev, se_idx, apdu,
 			apdu_length, cb, cb_context);
 
+	device_unlock(&dev->dev);
+	return rc;
+
 error:
 	device_unlock(&dev->dev);
+	kfree(cb_context);
 	return rc;
 }
 
@@ -1493,6 +1511,7 @@
 	u32 dev_idx, se_idx;
 	u8 *apdu;
 	size_t apdu_len;
+	int rc;
 
 	if (!info->attrs[NFC_ATTR_DEVICE_INDEX] ||
 	    !info->attrs[NFC_ATTR_SE_INDEX] ||
@@ -1506,25 +1525,37 @@
 	if (!dev)
 		return -ENODEV;
 
-	if (!dev->ops || !dev->ops->se_io)
-		return -ENOTSUPP;
+	if (!dev->ops || !dev->ops->se_io) {
+		rc = -EOPNOTSUPP;
+		goto put_dev;
+	}
 
 	apdu_len = nla_len(info->attrs[NFC_ATTR_SE_APDU]);
-	if (apdu_len == 0)
-		return -EINVAL;
+	if (apdu_len == 0) {
+		rc = -EINVAL;
+		goto put_dev;
+	}
 
 	apdu = nla_data(info->attrs[NFC_ATTR_SE_APDU]);
-	if (!apdu)
-		return -EINVAL;
+	if (!apdu) {
+		rc = -EINVAL;
+		goto put_dev;
+	}
 
 	ctx = kzalloc(sizeof(struct se_io_ctx), GFP_KERNEL);
-	if (!ctx)
-		return -ENOMEM;
+	if (!ctx) {
+		rc = -ENOMEM;
+		goto put_dev;
+	}
 
 	ctx->dev_idx = dev_idx;
 	ctx->se_idx = se_idx;
 
-	return nfc_se_io(dev, se_idx, apdu, apdu_len, se_io_cb, ctx);
+	rc = nfc_se_io(dev, se_idx, apdu, apdu_len, se_io_cb, ctx);
+
+put_dev:
+	nfc_put_device(dev);
+	return rc;
 }
 
 static int nfc_genl_vendor_cmd(struct sk_buff *skb,
@@ -1547,14 +1578,21 @@
 	subcmd = nla_get_u32(info->attrs[NFC_ATTR_VENDOR_SUBCMD]);
 
 	dev = nfc_get_device(dev_idx);
-	if (!dev || !dev->vendor_cmds || !dev->n_vendor_cmds)
+	if (!dev)
 		return -ENODEV;
 
+	if (!dev->vendor_cmds || !dev->n_vendor_cmds) {
+		err = -ENODEV;
+		goto put_dev;
+	}
+
 	if (info->attrs[NFC_ATTR_VENDOR_DATA]) {
 		data = nla_data(info->attrs[NFC_ATTR_VENDOR_DATA]);
 		data_len = nla_len(info->attrs[NFC_ATTR_VENDOR_DATA]);
-		if (data_len == 0)
-			return -EINVAL;
+		if (data_len == 0) {
+			err = -EINVAL;
+			goto put_dev;
+		}
 	} else {
 		data = NULL;
 		data_len = 0;
@@ -1569,10 +1607,14 @@
 		dev->cur_cmd_info = info;
 		err = cmd->doit(dev, data, data_len);
 		dev->cur_cmd_info = NULL;
-		return err;
+		goto put_dev;
 	}
 
-	return -EOPNOTSUPP;
+	err = -EOPNOTSUPP;
+
+put_dev:
+	nfc_put_device(dev);
+	return err;
 }
 
 /* message building helper */
--- linux-xilinx-zynqmp-5.15.0.orig/net/nfc/nfc.h
+++ linux-xilinx-zynqmp-5.15.0/net/nfc/nfc.h
@@ -52,6 +52,7 @@
 u8 *nfc_llcp_general_bytes(struct nfc_dev *dev, size_t *general_bytes_len);
 int nfc_llcp_data_received(struct nfc_dev *dev, struct sk_buff *skb);
 struct nfc_llcp_local *nfc_llcp_find_local(struct nfc_dev *dev);
+int nfc_llcp_local_put(struct nfc_llcp_local *local);
 int __init nfc_llcp_init(void);
 void nfc_llcp_exit(void);
 void nfc_llcp_free_sdp_tlv(struct nfc_llcp_sdp_tlv *sdp);
--- linux-xilinx-zynqmp-5.15.0.orig/net/nsh/nsh.c
+++ linux-xilinx-zynqmp-5.15.0/net/nsh/nsh.c
@@ -76,14 +76,15 @@
 static struct sk_buff *nsh_gso_segment(struct sk_buff *skb,
 				       netdev_features_t features)
 {
+	unsigned int outer_hlen, mac_len, nsh_len;
 	struct sk_buff *segs = ERR_PTR(-EINVAL);
-	unsigned int nsh_len, mac_len;
-	__be16 proto;
-	int nhoff;
+	u16 mac_offset = skb->mac_header;
+	__be16 outer_proto, proto;
 
 	skb_reset_network_header(skb);
 
-	nhoff = skb->network_header - skb->mac_header;
+	outer_proto = skb->protocol;
+	outer_hlen = skb_mac_header_len(skb);
 	mac_len = skb->mac_len;
 
 	if (unlikely(!pskb_may_pull(skb, NSH_BASE_HDR_LEN)))
@@ -108,16 +109,15 @@
 	segs = skb_mac_gso_segment(skb, features);
 	if (IS_ERR_OR_NULL(segs)) {
 		skb_gso_error_unwind(skb, htons(ETH_P_NSH), nsh_len,
-				     skb->network_header - nhoff,
-				     mac_len);
+				     mac_offset, mac_len);
 		goto out;
 	}
 
 	for (skb = segs; skb; skb = skb->next) {
-		skb->protocol = htons(ETH_P_NSH);
-		__skb_push(skb, nsh_len);
-		skb_set_mac_header(skb, -nhoff);
-		skb->network_header = skb->mac_header + mac_len;
+		skb->protocol = outer_proto;
+		__skb_push(skb, nsh_len + outer_hlen);
+		skb_reset_mac_header(skb);
+		skb_set_network_header(skb, outer_hlen);
 		skb->mac_len = mac_len;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/openvswitch/actions.c
+++ linux-xilinx-zynqmp-5.15.0/net/openvswitch/actions.c
@@ -373,6 +373,7 @@
 	update_ip_l4_checksum(skb, nh, *addr, new_addr);
 	csum_replace4(&nh->check, *addr, new_addr);
 	skb_clear_hash(skb);
+	ovs_ct_clear(skb, NULL);
 	*addr = new_addr;
 }
 
@@ -420,15 +421,47 @@
 		update_ipv6_checksum(skb, l4_proto, addr, new_addr);
 
 	skb_clear_hash(skb);
+	ovs_ct_clear(skb, NULL);
 	memcpy(addr, new_addr, sizeof(__be32[4]));
 }
 
-static void set_ipv6_fl(struct ipv6hdr *nh, u32 fl, u32 mask)
+static void set_ipv6_dsfield(struct sk_buff *skb, struct ipv6hdr *nh, u8 ipv6_tclass, u8 mask)
 {
+	u8 old_ipv6_tclass = ipv6_get_dsfield(nh);
+
+	ipv6_tclass = OVS_MASKED(old_ipv6_tclass, ipv6_tclass, mask);
+
+	if (skb->ip_summed == CHECKSUM_COMPLETE)
+		csum_replace(&skb->csum, (__force __wsum)(old_ipv6_tclass << 12),
+			     (__force __wsum)(ipv6_tclass << 12));
+
+	ipv6_change_dsfield(nh, ~mask, ipv6_tclass);
+}
+
+static void set_ipv6_fl(struct sk_buff *skb, struct ipv6hdr *nh, u32 fl, u32 mask)
+{
+	u32 ofl;
+
+	ofl = nh->flow_lbl[0] << 16 |  nh->flow_lbl[1] << 8 |  nh->flow_lbl[2];
+	fl = OVS_MASKED(ofl, fl, mask);
+
 	/* Bits 21-24 are always unmasked, so this retains their values. */
-	OVS_SET_MASKED(nh->flow_lbl[0], (u8)(fl >> 16), (u8)(mask >> 16));
-	OVS_SET_MASKED(nh->flow_lbl[1], (u8)(fl >> 8), (u8)(mask >> 8));
-	OVS_SET_MASKED(nh->flow_lbl[2], (u8)fl, (u8)mask);
+	nh->flow_lbl[0] = (u8)(fl >> 16);
+	nh->flow_lbl[1] = (u8)(fl >> 8);
+	nh->flow_lbl[2] = (u8)fl;
+
+	if (skb->ip_summed == CHECKSUM_COMPLETE)
+		csum_replace(&skb->csum, (__force __wsum)htonl(ofl), (__force __wsum)htonl(fl));
+}
+
+static void set_ipv6_ttl(struct sk_buff *skb, struct ipv6hdr *nh, u8 new_ttl, u8 mask)
+{
+	new_ttl = OVS_MASKED(nh->hop_limit, new_ttl, mask);
+
+	if (skb->ip_summed == CHECKSUM_COMPLETE)
+		csum_replace(&skb->csum, (__force __wsum)(nh->hop_limit << 8),
+			     (__force __wsum)(new_ttl << 8));
+	nh->hop_limit = new_ttl;
 }
 
 static void set_ip_ttl(struct sk_buff *skb, struct iphdr *nh, u8 new_ttl,
@@ -546,18 +579,17 @@
 		}
 	}
 	if (mask->ipv6_tclass) {
-		ipv6_change_dsfield(nh, ~mask->ipv6_tclass, key->ipv6_tclass);
+		set_ipv6_dsfield(skb, nh, key->ipv6_tclass, mask->ipv6_tclass);
 		flow_key->ip.tos = ipv6_get_dsfield(nh);
 	}
 	if (mask->ipv6_label) {
-		set_ipv6_fl(nh, ntohl(key->ipv6_label),
+		set_ipv6_fl(skb, nh, ntohl(key->ipv6_label),
 			    ntohl(mask->ipv6_label));
 		flow_key->ipv6.label =
 		    *(__be32 *)nh & htonl(IPV6_FLOWINFO_FLOWLABEL);
 	}
 	if (mask->ipv6_hlimit) {
-		OVS_SET_MASKED(nh->hop_limit, key->ipv6_hlimit,
-			       mask->ipv6_hlimit);
+		set_ipv6_ttl(skb, nh, key->ipv6_hlimit, mask->ipv6_hlimit);
 		flow_key->ip.ttl = nh->hop_limit;
 	}
 	return 0;
@@ -630,6 +662,7 @@
 static void set_tp_port(struct sk_buff *skb, __be16 *port,
 			__be16 new_port, __sum16 *check)
 {
+	ovs_ct_clear(skb, NULL);
 	inet_proto_csum_replace2(check, skb, *port, new_port, false);
 	*port = new_port;
 }
@@ -669,6 +702,7 @@
 		uh->dest = dst;
 		flow_key->tp.src = src;
 		flow_key->tp.dst = dst;
+		ovs_ct_clear(skb, NULL);
 	}
 
 	skb_clear_hash(skb);
@@ -731,6 +765,8 @@
 	sh->checksum = old_csum ^ old_correct_csum ^ new_csum;
 
 	skb_clear_hash(skb);
+	ovs_ct_clear(skb, NULL);
+
 	flow_key->tp.src = sh->source;
 	flow_key->tp.dst = sh->dest;
 
@@ -1021,7 +1057,7 @@
 	int rem = nla_len(attr);
 	bool dont_clone_flow_key;
 
-	/* The first action is always 'OVS_CLONE_ATTR_ARG'. */
+	/* The first action is always 'OVS_CLONE_ATTR_EXEC'. */
 	clone_arg = nla_data(attr);
 	dont_clone_flow_key = nla_get_u32(clone_arg);
 	actions = nla_next(clone_arg, &rem);
--- linux-xilinx-zynqmp-5.15.0.orig/net/openvswitch/conntrack.c
+++ linux-xilinx-zynqmp-5.15.0/net/openvswitch/conntrack.c
@@ -150,7 +150,7 @@
 static u32 ovs_ct_get_mark(const struct nf_conn *ct)
 {
 #if IS_ENABLED(CONFIG_NF_CONNTRACK_MARK)
-	return ct ? ct->mark : 0;
+	return ct ? READ_ONCE(ct->mark) : 0;
 #else
 	return 0;
 #endif
@@ -338,9 +338,9 @@
 #if IS_ENABLED(CONFIG_NF_CONNTRACK_MARK)
 	u32 new_mark;
 
-	new_mark = ct_mark | (ct->mark & ~(mask));
-	if (ct->mark != new_mark) {
-		ct->mark = new_mark;
+	new_mark = ct_mark | (READ_ONCE(ct->mark) & ~(mask));
+	if (READ_ONCE(ct->mark) != new_mark) {
+		WRITE_ONCE(ct->mark, new_mark);
 		if (nf_ct_is_confirmed(ct))
 			nf_conntrack_event_cache(IPCT_MARK, ct);
 		key->ct.mark = new_mark;
@@ -574,7 +574,7 @@
 			struct nf_conn *ct = nf_ct_tuplehash_to_ctrack(h);
 
 			nf_ct_delete(ct, 0, 0);
-			nf_conntrack_put(&ct->ct_general);
+			nf_ct_put(ct);
 		}
 	}
 
@@ -723,7 +723,7 @@
 		if (nf_ct_is_confirmed(ct))
 			nf_ct_delete(ct, 0, 0);
 
-		nf_conntrack_put(&ct->ct_general);
+		nf_ct_put(ct);
 		nf_ct_set(skb, NULL, 0);
 		return false;
 	}
@@ -732,6 +732,57 @@
 }
 
 #if IS_ENABLED(CONFIG_NF_NAT)
+static void ovs_nat_update_key(struct sw_flow_key *key,
+			       const struct sk_buff *skb,
+			       enum nf_nat_manip_type maniptype)
+{
+	if (maniptype == NF_NAT_MANIP_SRC) {
+		__be16 src;
+
+		key->ct_state |= OVS_CS_F_SRC_NAT;
+		if (key->eth.type == htons(ETH_P_IP))
+			key->ipv4.addr.src = ip_hdr(skb)->saddr;
+		else if (key->eth.type == htons(ETH_P_IPV6))
+			memcpy(&key->ipv6.addr.src, &ipv6_hdr(skb)->saddr,
+			       sizeof(key->ipv6.addr.src));
+		else
+			return;
+
+		if (key->ip.proto == IPPROTO_UDP)
+			src = udp_hdr(skb)->source;
+		else if (key->ip.proto == IPPROTO_TCP)
+			src = tcp_hdr(skb)->source;
+		else if (key->ip.proto == IPPROTO_SCTP)
+			src = sctp_hdr(skb)->source;
+		else
+			return;
+
+		key->tp.src = src;
+	} else {
+		__be16 dst;
+
+		key->ct_state |= OVS_CS_F_DST_NAT;
+		if (key->eth.type == htons(ETH_P_IP))
+			key->ipv4.addr.dst = ip_hdr(skb)->daddr;
+		else if (key->eth.type == htons(ETH_P_IPV6))
+			memcpy(&key->ipv6.addr.dst, &ipv6_hdr(skb)->daddr,
+			       sizeof(key->ipv6.addr.dst));
+		else
+			return;
+
+		if (key->ip.proto == IPPROTO_UDP)
+			dst = udp_hdr(skb)->dest;
+		else if (key->ip.proto == IPPROTO_TCP)
+			dst = tcp_hdr(skb)->dest;
+		else if (key->ip.proto == IPPROTO_SCTP)
+			dst = sctp_hdr(skb)->dest;
+		else
+			return;
+
+		key->tp.dst = dst;
+	}
+}
+
 /* Modelled after nf_nat_ipv[46]_fn().
  * range is only used for new, uninitialized NAT state.
  * Returns either NF_ACCEPT or NF_DROP.
@@ -739,7 +790,7 @@
 static int ovs_ct_nat_execute(struct sk_buff *skb, struct nf_conn *ct,
 			      enum ip_conntrack_info ctinfo,
 			      const struct nf_nat_range2 *range,
-			      enum nf_nat_manip_type maniptype)
+			      enum nf_nat_manip_type maniptype, struct sw_flow_key *key)
 {
 	int hooknum, nh_off, err = NF_ACCEPT;
 
@@ -811,58 +862,11 @@
 push:
 	skb_push_rcsum(skb, nh_off);
 
-	return err;
-}
-
-static void ovs_nat_update_key(struct sw_flow_key *key,
-			       const struct sk_buff *skb,
-			       enum nf_nat_manip_type maniptype)
-{
-	if (maniptype == NF_NAT_MANIP_SRC) {
-		__be16 src;
-
-		key->ct_state |= OVS_CS_F_SRC_NAT;
-		if (key->eth.type == htons(ETH_P_IP))
-			key->ipv4.addr.src = ip_hdr(skb)->saddr;
-		else if (key->eth.type == htons(ETH_P_IPV6))
-			memcpy(&key->ipv6.addr.src, &ipv6_hdr(skb)->saddr,
-			       sizeof(key->ipv6.addr.src));
-		else
-			return;
-
-		if (key->ip.proto == IPPROTO_UDP)
-			src = udp_hdr(skb)->source;
-		else if (key->ip.proto == IPPROTO_TCP)
-			src = tcp_hdr(skb)->source;
-		else if (key->ip.proto == IPPROTO_SCTP)
-			src = sctp_hdr(skb)->source;
-		else
-			return;
-
-		key->tp.src = src;
-	} else {
-		__be16 dst;
-
-		key->ct_state |= OVS_CS_F_DST_NAT;
-		if (key->eth.type == htons(ETH_P_IP))
-			key->ipv4.addr.dst = ip_hdr(skb)->daddr;
-		else if (key->eth.type == htons(ETH_P_IPV6))
-			memcpy(&key->ipv6.addr.dst, &ipv6_hdr(skb)->daddr,
-			       sizeof(key->ipv6.addr.dst));
-		else
-			return;
-
-		if (key->ip.proto == IPPROTO_UDP)
-			dst = udp_hdr(skb)->dest;
-		else if (key->ip.proto == IPPROTO_TCP)
-			dst = tcp_hdr(skb)->dest;
-		else if (key->ip.proto == IPPROTO_SCTP)
-			dst = sctp_hdr(skb)->dest;
-		else
-			return;
+	/* Update the flow key if NAT successful. */
+	if (err == NF_ACCEPT)
+		ovs_nat_update_key(key, skb, maniptype);
 
-		key->tp.dst = dst;
-	}
+	return err;
 }
 
 /* Returns NF_DROP if the packet should be dropped, NF_ACCEPT otherwise. */
@@ -904,7 +908,7 @@
 	} else {
 		return NF_ACCEPT; /* Connection is not NATed. */
 	}
-	err = ovs_ct_nat_execute(skb, ct, ctinfo, &info->range, maniptype);
+	err = ovs_ct_nat_execute(skb, ct, ctinfo, &info->range, maniptype, key);
 
 	if (err == NF_ACCEPT && ct->status & IPS_DST_NAT) {
 		if (ct->status & IPS_SRC_NAT) {
@@ -914,17 +918,13 @@
 				maniptype = NF_NAT_MANIP_SRC;
 
 			err = ovs_ct_nat_execute(skb, ct, ctinfo, &info->range,
-						 maniptype);
+						 maniptype, key);
 		} else if (CTINFO2DIR(ctinfo) == IP_CT_DIR_ORIGINAL) {
 			err = ovs_ct_nat_execute(skb, ct, ctinfo, NULL,
-						 NF_NAT_MANIP_SRC);
+						 NF_NAT_MANIP_SRC, key);
 		}
 	}
 
-	/* Mark NAT done if successful and update the flow key. */
-	if (err == NF_ACCEPT)
-		ovs_nat_update_key(key, skb, maniptype);
-
 	return err;
 }
 #else /* !CONFIG_NF_NAT */
@@ -967,7 +967,8 @@
 
 		/* Associate skb with specified zone. */
 		if (tmpl) {
-			nf_conntrack_put(skb_nfct(skb));
+			ct = nf_ct_get(skb, &ctinfo);
+			nf_ct_put(ct);
 			nf_conntrack_get(&tmpl->ct_general);
 			nf_ct_set(skb, tmpl, IP_CT_NEW);
 		}
@@ -1328,9 +1329,16 @@
 
 int ovs_ct_clear(struct sk_buff *skb, struct sw_flow_key *key)
 {
-	nf_conntrack_put(skb_nfct(skb));
+	enum ip_conntrack_info ctinfo;
+	struct nf_conn *ct;
+
+	ct = nf_ct_get(skb, &ctinfo);
+
+	nf_ct_put(ct);
 	nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
-	ovs_ct_fill_key(skb, key, false);
+
+	if (key)
+		ovs_ct_fill_key(skb, key, false);
 
 	return 0;
 }
@@ -1696,8 +1704,9 @@
 	if (ct_info.timeout[0]) {
 		if (nf_ct_set_timeout(net, ct_info.ct, family, key->ip.proto,
 				      ct_info.timeout))
-			pr_info_ratelimited("Failed to associated timeout "
-					    "policy `%s'\n", ct_info.timeout);
+			OVS_NLERR(log,
+				  "Failed to associated timeout policy '%s'",
+				  ct_info.timeout);
 		else
 			ct_info.nf_ct_timeout = rcu_dereference(
 				nf_ct_timeout_find(ct_info.ct)->timeout);
@@ -1716,7 +1725,6 @@
 		goto err_free_ct;
 
 	__set_bit(IPS_CONFIRMED_BIT, &ct_info.ct->status);
-	nf_conntrack_get(&ct_info.ct->ct_general);
 	return 0;
 err_free_ct:
 	__ovs_ct_free_action(&ct_info);
@@ -1905,9 +1913,9 @@
 	for (i = 0; i < CT_LIMIT_HASH_BUCKETS; ++i) {
 		struct hlist_head *head = &info->limits[i];
 		struct ovs_ct_limit *ct_limit;
+		struct hlist_node *next;
 
-		hlist_for_each_entry_rcu(ct_limit, head, hlist_node,
-					 lockdep_ovsl_is_held())
+		hlist_for_each_entry_safe(ct_limit, next, head, hlist_node)
 			kfree_rcu(ct_limit, rcu);
 	}
 	kfree(info->limits);
--- linux-xilinx-zynqmp-5.15.0.orig/net/openvswitch/datapath.c
+++ linux-xilinx-zynqmp-5.15.0/net/openvswitch/datapath.c
@@ -251,10 +251,17 @@
 
 		upcall.mru = OVS_CB(skb)->mru;
 		error = ovs_dp_upcall(dp, skb, key, &upcall, 0);
-		if (unlikely(error))
-			kfree_skb(skb);
-		else
+		switch (error) {
+		case 0:
+		case -EAGAIN:
+		case -ERESTARTSYS:
+		case -EINTR:
 			consume_skb(skb);
+			break;
+		default:
+			kfree_skb(skb);
+			break;
+		}
 		stats_counter = &stats->n_missed;
 		goto out;
 	}
@@ -550,8 +557,9 @@
 out:
 	if (err)
 		skb_tx_error(skb);
-	kfree_skb(user_skb);
-	kfree_skb(nskb);
+	consume_skb(user_skb);
+	consume_skb(nskb);
+
 	return err;
 }
 
@@ -938,6 +946,7 @@
 	struct sw_flow_mask mask;
 	struct sk_buff *reply;
 	struct datapath *dp;
+	struct sw_flow_key *key;
 	struct sw_flow_actions *acts;
 	struct sw_flow_match match;
 	u32 ufid_flags = ovs_nla_get_ufid_flags(a[OVS_FLOW_ATTR_UFID_FLAGS]);
@@ -965,30 +974,32 @@
 	}
 
 	/* Extract key. */
-	ovs_match_init(&match, &new_flow->key, false, &mask);
+	key = kzalloc(sizeof(*key), GFP_KERNEL);
+	if (!key) {
+		error = -ENOMEM;
+		goto err_kfree_flow;
+	}
+
+	ovs_match_init(&match, key, false, &mask);
 	error = ovs_nla_get_match(net, &match, a[OVS_FLOW_ATTR_KEY],
 				  a[OVS_FLOW_ATTR_MASK], log);
 	if (error)
-		goto err_kfree_flow;
+		goto err_kfree_key;
+
+	ovs_flow_mask_key(&new_flow->key, key, true, &mask);
 
 	/* Extract flow identifier. */
 	error = ovs_nla_get_identifier(&new_flow->id, a[OVS_FLOW_ATTR_UFID],
-				       &new_flow->key, log);
+				       key, log);
 	if (error)
-		goto err_kfree_flow;
-
-	/* unmasked key is needed to match when ufid is not used. */
-	if (ovs_identifier_is_key(&new_flow->id))
-		match.key = new_flow->id.unmasked_key;
-
-	ovs_flow_mask_key(&new_flow->key, &new_flow->key, true, &mask);
+		goto err_kfree_key;
 
 	/* Validate actions. */
 	error = ovs_nla_copy_actions(net, a[OVS_FLOW_ATTR_ACTIONS],
 				     &new_flow->key, &acts, log);
 	if (error) {
 		OVS_NLERR(log, "Flow actions may not be safe on all matching packets.");
-		goto err_kfree_flow;
+		goto err_kfree_key;
 	}
 
 	reply = ovs_flow_cmd_alloc_info(acts, &new_flow->id, info, false,
@@ -1009,7 +1020,7 @@
 	if (ovs_identifier_is_ufid(&new_flow->id))
 		flow = ovs_flow_tbl_lookup_ufid(&dp->table, &new_flow->id);
 	if (!flow)
-		flow = ovs_flow_tbl_lookup(&dp->table, &new_flow->key);
+		flow = ovs_flow_tbl_lookup(&dp->table, key);
 	if (likely(!flow)) {
 		rcu_assign_pointer(new_flow->sf_acts, acts);
 
@@ -1079,6 +1090,8 @@
 
 	if (reply)
 		ovs_notify(&dp_flow_genl_family, reply, info);
+
+	kfree(key);
 	return 0;
 
 err_unlock_ovs:
@@ -1086,6 +1099,8 @@
 	kfree_skb(reply);
 err_kfree_acts:
 	ovs_nla_free_flow_actions(acts);
+err_kfree_key:
+	kfree(key);
 err_kfree_flow:
 	ovs_flow_free(new_flow, false);
 error:
@@ -1597,7 +1612,8 @@
 	if (IS_ERR(dp))
 		return;
 
-	WARN(dp->user_features, "Dropping previously announced user features\n");
+	pr_warn("%s: Dropping previously announced user features\n",
+		ovs_dp_name(dp));
 	dp->user_features = 0;
 }
 
@@ -1801,7 +1817,7 @@
 				ovs_dp_reset_user_features(skb, info);
 		}
 
-		goto err_unlock_and_destroy_meters;
+		goto err_destroy_portids;
 	}
 
 	err = ovs_dp_cmd_fill_info(dp, reply, info->snd_portid,
@@ -1816,6 +1832,8 @@
 	ovs_notify(&dp_datapath_genl_family, reply, info);
 	return 0;
 
+err_destroy_portids:
+	kfree(rcu_dereference_raw(dp->upcall_portids));
 err_unlock_and_destroy_meters:
 	ovs_unlock();
 	ovs_meters_exit(dp);
@@ -2040,6 +2058,7 @@
 {
 	struct ovs_header *ovs_header;
 	struct ovs_vport_stats vport_stats;
+	struct net *net_vport;
 	int err;
 
 	ovs_header = genlmsg_put(skb, portid, seq, &dp_vport_genl_family,
@@ -2056,12 +2075,15 @@
 	    nla_put_u32(skb, OVS_VPORT_ATTR_IFINDEX, vport->dev->ifindex))
 		goto nla_put_failure;
 
-	if (!net_eq(net, dev_net(vport->dev))) {
-		int id = peernet2id_alloc(net, dev_net(vport->dev), gfp);
+	rcu_read_lock();
+	net_vport = dev_net_rcu(vport->dev);
+	if (!net_eq(net, net_vport)) {
+		int id = peernet2id_alloc(net, net_vport, GFP_ATOMIC);
 
 		if (nla_put_s32(skb, OVS_VPORT_ATTR_NETNSID, id))
-			goto nla_put_failure;
+			goto nla_put_failure_unlock;
 	}
+	rcu_read_unlock();
 
 	ovs_vport_get_stats(vport, &vport_stats);
 	if (nla_put_64bit(skb, OVS_VPORT_ATTR_STATS,
@@ -2079,6 +2101,8 @@
 	genlmsg_end(skb, ovs_header);
 	return 0;
 
+nla_put_failure_unlock:
+	rcu_read_unlock();
 nla_put_failure:
 	err = -EMSGSIZE;
 error:
--- linux-xilinx-zynqmp-5.15.0.orig/net/openvswitch/flow.c
+++ linux-xilinx-zynqmp-5.15.0/net/openvswitch/flow.c
@@ -34,6 +34,7 @@
 #include <net/mpls.h>
 #include <net/ndisc.h>
 #include <net/nsh.h>
+#include <net/netfilter/nf_conntrack_zones.h>
 
 #include "conntrack.h"
 #include "datapath.h"
@@ -265,7 +266,7 @@
 	if (flags & IP6_FH_F_FRAG) {
 		if (frag_off) {
 			key->ip.frag = OVS_FRAG_TYPE_LATER;
-			key->ip.proto = nexthdr;
+			key->ip.proto = NEXTHDR_FRAGMENT;
 			return 0;
 		}
 		key->ip.frag = OVS_FRAG_TYPE_FIRST;
@@ -416,7 +417,6 @@
 	 */
 	key->tp.src = htons(icmp->icmp6_type);
 	key->tp.dst = htons(icmp->icmp6_code);
-	memset(&key->ipv6.nd, 0, sizeof(key->ipv6.nd));
 
 	if (icmp->icmp6_code == 0 &&
 	    (icmp->icmp6_type == NDISC_NEIGHBOUR_SOLICITATION ||
@@ -425,6 +425,8 @@
 		struct nd_msg *nd;
 		int offset;
 
+		memset(&key->ipv6.nd, 0, sizeof(key->ipv6.nd));
+
 		/* In order to process neighbor discovery options, we need the
 		 * entire packet.
 		 */
@@ -858,8 +860,9 @@
 #if IS_ENABLED(CONFIG_NET_TC_SKB_EXT)
 	struct tc_skb_ext *tc_ext;
 #endif
-	bool post_ct = false;
+	bool post_ct = false, post_ct_snat = false, post_ct_dnat = false;
 	int res, err;
+	u16 zone = 0;
 
 	/* Extract metadata from packet. */
 	if (tun_info) {
@@ -898,6 +901,9 @@
 		key->recirc_id = tc_ext ? tc_ext->chain : 0;
 		OVS_CB(skb)->mru = tc_ext ? tc_ext->mru : 0;
 		post_ct = tc_ext ? tc_ext->post_ct : false;
+		post_ct_snat = post_ct ? tc_ext->post_ct_snat : false;
+		post_ct_dnat = post_ct ? tc_ext->post_ct_dnat : false;
+		zone = post_ct ? tc_ext->zone : 0;
 	} else {
 		key->recirc_id = 0;
 	}
@@ -906,8 +912,19 @@
 #endif
 
 	err = key_extract(skb, key);
-	if (!err)
+	if (!err) {
 		ovs_ct_fill_key(skb, key, post_ct);   /* Must be after key_extract(). */
+		if (post_ct) {
+			if (!skb_get_nfct(skb)) {
+				key->ct_zone = zone;
+			} else {
+				if (!post_ct_dnat)
+					key->ct_state &= ~OVS_CS_F_DST_NAT;
+				if (!post_ct_snat)
+					key->ct_state &= ~OVS_CS_F_SRC_NAT;
+			}
+		}
+	}
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/openvswitch/flow_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/openvswitch/flow_netlink.c
@@ -47,6 +47,7 @@
 
 #define OVS_ATTR_NESTED -1
 #define OVS_ATTR_VARIABLE -2
+#define OVS_COPY_ACTIONS_MAX_DEPTH 16
 
 static bool actions_may_change_flow(const struct nlattr *actions)
 {
@@ -2201,8 +2202,8 @@
 			icmpv6_key->icmpv6_type = ntohs(output->tp.src);
 			icmpv6_key->icmpv6_code = ntohs(output->tp.dst);
 
-			if (icmpv6_key->icmpv6_type == NDISC_NEIGHBOUR_SOLICITATION ||
-			    icmpv6_key->icmpv6_type == NDISC_NEIGHBOUR_ADVERTISEMENT) {
+			if (swkey->tp.src == htons(NDISC_NEIGHBOUR_SOLICITATION) ||
+			    swkey->tp.src == htons(NDISC_NEIGHBOUR_ADVERTISEMENT)) {
 				struct ovs_key_nd *nd_key;
 
 				nla = nla_reserve(skb, OVS_KEY_ATTR_ND, sizeof(*nd_key));
@@ -2272,15 +2273,11 @@
 				OVS_FLOW_ATTR_MASK, true, skb);
 }
 
-#define MAX_ACTIONS_BUFSIZE	(32 * 1024)
-
 static struct sw_flow_actions *nla_alloc_flow_actions(int size)
 {
 	struct sw_flow_actions *sfa;
 
-	WARN_ON_ONCE(size > MAX_ACTIONS_BUFSIZE);
-
-	sfa = kmalloc(sizeof(*sfa) + size, GFP_KERNEL);
+	sfa = kmalloc(kmalloc_size_roundup(sizeof(*sfa) + size), GFP_KERNEL);
 	if (!sfa)
 		return ERR_PTR(-ENOMEM);
 
@@ -2288,6 +2285,62 @@
 	return sfa;
 }
 
+static void ovs_nla_free_nested_actions(const struct nlattr *actions, int len);
+
+static void ovs_nla_free_check_pkt_len_action(const struct nlattr *action)
+{
+	const struct nlattr *a;
+	int rem;
+
+	nla_for_each_nested(a, action, rem) {
+		switch (nla_type(a)) {
+		case OVS_CHECK_PKT_LEN_ATTR_ACTIONS_IF_LESS_EQUAL:
+		case OVS_CHECK_PKT_LEN_ATTR_ACTIONS_IF_GREATER:
+			ovs_nla_free_nested_actions(nla_data(a), nla_len(a));
+			break;
+		}
+	}
+}
+
+static void ovs_nla_free_clone_action(const struct nlattr *action)
+{
+	const struct nlattr *a = nla_data(action);
+	int rem = nla_len(action);
+
+	switch (nla_type(a)) {
+	case OVS_CLONE_ATTR_EXEC:
+		/* The real list of actions follows this attribute. */
+		a = nla_next(a, &rem);
+		ovs_nla_free_nested_actions(a, rem);
+		break;
+	}
+}
+
+static void ovs_nla_free_dec_ttl_action(const struct nlattr *action)
+{
+	const struct nlattr *a = nla_data(action);
+
+	switch (nla_type(a)) {
+	case OVS_DEC_TTL_ATTR_ACTION:
+		ovs_nla_free_nested_actions(nla_data(a), nla_len(a));
+		break;
+	}
+}
+
+static void ovs_nla_free_sample_action(const struct nlattr *action)
+{
+	const struct nlattr *a = nla_data(action);
+	int rem = nla_len(action);
+
+	switch (nla_type(a)) {
+	case OVS_SAMPLE_ATTR_ARG:
+		/* The real list of actions follows this attribute. */
+		a = nla_next(a, &rem);
+		ovs_nla_free_nested_actions(a, rem);
+		break;
+	}
+}
+
 static void ovs_nla_free_set_action(const struct nlattr *a)
 {
 	const struct nlattr *ovs_key = nla_data(a);
@@ -2301,25 +2354,54 @@
 	}
 }
 
-void ovs_nla_free_flow_actions(struct sw_flow_actions *sf_acts)
+static void ovs_nla_free_nested_actions(const struct nlattr *actions, int len)
 {
 	const struct nlattr *a;
 	int rem;
 
-	if (!sf_acts)
+	/* Whenever new actions are added, the need to update this
+	 * function should be considered.
+	 */
+	BUILD_BUG_ON(OVS_ACTION_ATTR_MAX != 23);
+
+	if (!actions)
 		return;
 
-	nla_for_each_attr(a, sf_acts->actions, sf_acts->actions_len, rem) {
+	nla_for_each_attr(a, actions, len, rem) {
 		switch (nla_type(a)) {
-		case OVS_ACTION_ATTR_SET:
-			ovs_nla_free_set_action(a);
+		case OVS_ACTION_ATTR_CHECK_PKT_LEN:
+			ovs_nla_free_check_pkt_len_action(a);
 			break;
+
+		case OVS_ACTION_ATTR_CLONE:
+			ovs_nla_free_clone_action(a);
+			break;
+
 		case OVS_ACTION_ATTR_CT:
 			ovs_ct_free_action(a);
 			break;
+
+		case OVS_ACTION_ATTR_DEC_TTL:
+			ovs_nla_free_dec_ttl_action(a);
+			break;
+
+		case OVS_ACTION_ATTR_SAMPLE:
+			ovs_nla_free_sample_action(a);
+			break;
+
+		case OVS_ACTION_ATTR_SET:
+			ovs_nla_free_set_action(a);
+			break;
 		}
 	}
+}
 
+void ovs_nla_free_flow_actions(struct sw_flow_actions *sf_acts)
+{
+	if (!sf_acts)
+		return;
+
+	ovs_nla_free_nested_actions(sf_acts->actions, sf_acts->actions_len);
 	kfree(sf_acts);
 }
 
@@ -2350,15 +2432,6 @@
 
 	new_acts_size = max(next_offset + req_size, ksize(*sfa) * 2);
 
-	if (new_acts_size > MAX_ACTIONS_BUFSIZE) {
-		if ((MAX_ACTIONS_BUFSIZE - next_offset) < req_size) {
-			OVS_NLERR(log, "Flow action size exceeds max %u",
-				  MAX_ACTIONS_BUFSIZE);
-			return ERR_PTR(-EMSGSIZE);
-		}
-		new_acts_size = MAX_ACTIONS_BUFSIZE;
-	}
-
 	acts = nla_alloc_flow_actions(new_acts_size);
 	if (IS_ERR(acts))
 		return (void *)acts;
@@ -2429,13 +2502,15 @@
 				  const struct sw_flow_key *key,
 				  struct sw_flow_actions **sfa,
 				  __be16 eth_type, __be16 vlan_tci,
-				  u32 mpls_label_count, bool log);
+				  u32 mpls_label_count, bool log,
+				  u32 depth);
 
 static int validate_and_copy_sample(struct net *net, const struct nlattr *attr,
 				    const struct sw_flow_key *key,
 				    struct sw_flow_actions **sfa,
 				    __be16 eth_type, __be16 vlan_tci,
-				    u32 mpls_label_count, bool log, bool last)
+				    u32 mpls_label_count, bool log, bool last,
+				    u32 depth)
 {
 	const struct nlattr *attrs[OVS_SAMPLE_ATTR_MAX + 1];
 	const struct nlattr *probability, *actions;
@@ -2486,7 +2561,8 @@
 		return err;
 
 	err = __ovs_nla_copy_actions(net, actions, key, sfa,
-				     eth_type, vlan_tci, mpls_label_count, log);
+				     eth_type, vlan_tci, mpls_label_count, log,
+				     depth + 1);
 
 	if (err)
 		return err;
@@ -2501,7 +2577,8 @@
 				     const struct sw_flow_key *key,
 				     struct sw_flow_actions **sfa,
 				     __be16 eth_type, __be16 vlan_tci,
-				     u32 mpls_label_count, bool log)
+				     u32 mpls_label_count, bool log,
+				     u32 depth)
 {
 	const struct nlattr *attrs[OVS_DEC_TTL_ATTR_MAX + 1];
 	int start, action_start, err, rem;
@@ -2544,7 +2621,8 @@
 		return action_start;
 
 	err = __ovs_nla_copy_actions(net, actions, key, sfa, eth_type,
-				     vlan_tci, mpls_label_count, log);
+				     vlan_tci, mpls_label_count, log,
+				     depth + 1);
 	if (err)
 		return err;
 
@@ -2558,7 +2636,8 @@
 				   const struct sw_flow_key *key,
 				   struct sw_flow_actions **sfa,
 				   __be16 eth_type, __be16 vlan_tci,
-				   u32 mpls_label_count, bool log, bool last)
+				   u32 mpls_label_count, bool log, bool last,
+				   u32 depth)
 {
 	int start, err;
 	u32 exec;
@@ -2578,7 +2657,8 @@
 		return err;
 
 	err = __ovs_nla_copy_actions(net, attr, key, sfa,
-				     eth_type, vlan_tci, mpls_label_count, log);
+				     eth_type, vlan_tci, mpls_label_count, log,
+				     depth + 1);
 	if (err)
 		return err;
 
@@ -2947,7 +3027,7 @@
 					   struct sw_flow_actions **sfa,
 					   __be16 eth_type, __be16 vlan_tci,
 					   u32 mpls_label_count,
-					   bool log, bool last)
+					   bool log, bool last, u32 depth)
 {
 	const struct nlattr *acts_if_greater, *acts_if_lesser_eq;
 	struct nlattr *a[OVS_CHECK_PKT_LEN_ATTR_MAX + 1];
@@ -2995,7 +3075,8 @@
 		return nested_acts_start;
 
 	err = __ovs_nla_copy_actions(net, acts_if_lesser_eq, key, sfa,
-				     eth_type, vlan_tci, mpls_label_count, log);
+				     eth_type, vlan_tci, mpls_label_count, log,
+				     depth + 1);
 
 	if (err)
 		return err;
@@ -3008,7 +3089,8 @@
 		return nested_acts_start;
 
 	err = __ovs_nla_copy_actions(net, acts_if_greater, key, sfa,
-				     eth_type, vlan_tci, mpls_label_count, log);
+				     eth_type, vlan_tci, mpls_label_count, log,
+				     depth + 1);
 
 	if (err)
 		return err;
@@ -3036,12 +3118,16 @@
 				  const struct sw_flow_key *key,
 				  struct sw_flow_actions **sfa,
 				  __be16 eth_type, __be16 vlan_tci,
-				  u32 mpls_label_count, bool log)
+				  u32 mpls_label_count, bool log,
+				  u32 depth)
 {
 	u8 mac_proto = ovs_key_mac_proto(key);
 	const struct nlattr *a;
 	int rem, err;
 
+	if (depth > OVS_COPY_ACTIONS_MAX_DEPTH)
+		return -EOVERFLOW;
+
 	nla_for_each_nested(a, attr, rem) {
 		/* Expected argument lengths, (u32)-1 for variable length. */
 		static const u32 action_lens[OVS_ACTION_ATTR_MAX + 1] = {
@@ -3236,7 +3322,7 @@
 			err = validate_and_copy_sample(net, a, key, sfa,
 						       eth_type, vlan_tci,
 						       mpls_label_count,
-						       log, last);
+						       log, last, depth);
 			if (err)
 				return err;
 			skip_copy = true;
@@ -3307,7 +3393,7 @@
 			err = validate_and_copy_clone(net, a, key, sfa,
 						      eth_type, vlan_tci,
 						      mpls_label_count,
-						      log, last);
+						      log, last, depth);
 			if (err)
 				return err;
 			skip_copy = true;
@@ -3321,7 +3407,8 @@
 							      eth_type,
 							      vlan_tci,
 							      mpls_label_count,
-							      log, last);
+							      log, last,
+							      depth);
 			if (err)
 				return err;
 			skip_copy = true;
@@ -3331,7 +3418,8 @@
 		case OVS_ACTION_ATTR_DEC_TTL:
 			err = validate_and_copy_dec_ttl(net, a, key, sfa,
 							eth_type, vlan_tci,
-							mpls_label_count, log);
+							mpls_label_count, log,
+							depth);
 			if (err)
 				return err;
 			skip_copy = true;
@@ -3362,7 +3450,7 @@
 	int err;
 	u32 mpls_label_count = 0;
 
-	*sfa = nla_alloc_flow_actions(min(nla_len(attr), MAX_ACTIONS_BUFSIZE));
+	*sfa = nla_alloc_flow_actions(nla_len(attr));
 	if (IS_ERR(*sfa))
 		return PTR_ERR(*sfa);
 
@@ -3371,7 +3459,8 @@
 
 	(*sfa)->orig_len = nla_len(attr);
 	err = __ovs_nla_copy_actions(net, attr, key, sfa, key->eth.type,
-				     key->eth.vlan.tci, mpls_label_count, log);
+				     key->eth.vlan.tci, mpls_label_count, log,
+				     0);
 	if (err)
 		ovs_nla_free_flow_actions(*sfa);
 
@@ -3429,7 +3518,9 @@
 	if (!start)
 		return -EMSGSIZE;
 
-	err = ovs_nla_put_actions(nla_data(attr), rem, skb);
+	/* Skipping the OVS_CLONE_ATTR_EXEC that is always the first attribute. */
+	attr = nla_next(nla_data(attr), &rem);
+	err = ovs_nla_put_actions(attr, rem, skb);
 
 	if (err)
 		nla_nest_cancel(skb, start);
--- linux-xilinx-zynqmp-5.15.0.orig/net/openvswitch/meter.c
+++ linux-xilinx-zynqmp-5.15.0/net/openvswitch/meter.c
@@ -450,7 +450,7 @@
 
 	err = attach_meter(meter_tbl, meter);
 	if (err)
-		goto exit_unlock;
+		goto exit_free_old_meter;
 
 	ovs_unlock();
 
@@ -473,6 +473,8 @@
 	genlmsg_end(reply, ovs_reply_header);
 	return genlmsg_reply(reply, info);
 
+exit_free_old_meter:
+	ovs_meter_free(old_meter);
 exit_unlock:
 	ovs_unlock();
 	nlmsg_free(reply);
--- linux-xilinx-zynqmp-5.15.0.orig/net/packet/af_packet.c
+++ linux-xilinx-zynqmp-5.15.0/net/packet/af_packet.c
@@ -271,7 +271,8 @@
 
 static bool packet_use_direct_xmit(const struct packet_sock *po)
 {
-	return po->xmit == packet_direct_xmit;
+	/* Paired with WRITE_ONCE() in packet_setsockopt() */
+	return READ_ONCE(po->xmit) == packet_direct_xmit;
 }
 
 static u16 packet_pick_tx_queue(struct sk_buff *skb)
@@ -367,18 +368,20 @@
 {
 	union tpacket_uhdr h;
 
+	/* WRITE_ONCE() are paired with READ_ONCE() in __packet_get_status */
+
 	h.raw = frame;
 	switch (po->tp_version) {
 	case TPACKET_V1:
-		h.h1->tp_status = status;
+		WRITE_ONCE(h.h1->tp_status, status);
 		flush_dcache_page(pgv_to_page(&h.h1->tp_status));
 		break;
 	case TPACKET_V2:
-		h.h2->tp_status = status;
+		WRITE_ONCE(h.h2->tp_status, status);
 		flush_dcache_page(pgv_to_page(&h.h2->tp_status));
 		break;
 	case TPACKET_V3:
-		h.h3->tp_status = status;
+		WRITE_ONCE(h.h3->tp_status, status);
 		flush_dcache_page(pgv_to_page(&h.h3->tp_status));
 		break;
 	default:
@@ -395,17 +398,19 @@
 
 	smp_rmb();
 
+	/* READ_ONCE() are paired with WRITE_ONCE() in __packet_set_status */
+
 	h.raw = frame;
 	switch (po->tp_version) {
 	case TPACKET_V1:
 		flush_dcache_page(pgv_to_page(&h.h1->tp_status));
-		return h.h1->tp_status;
+		return READ_ONCE(h.h1->tp_status);
 	case TPACKET_V2:
 		flush_dcache_page(pgv_to_page(&h.h2->tp_status));
-		return h.h2->tp_status;
+		return READ_ONCE(h.h2->tp_status);
 	case TPACKET_V3:
 		flush_dcache_page(pgv_to_page(&h.h3->tp_status));
-		return h.h3->tp_status;
+		return READ_ONCE(h.h3->tp_status);
 	default:
 		WARN(1, "TPACKET version not supported.\n");
 		BUG();
@@ -500,6 +505,47 @@
 	return packet_lookup_frame(po, rb, rb->head, status);
 }
 
+static u16 vlan_get_tci(const struct sk_buff *skb, struct net_device *dev)
+{
+	struct vlan_hdr vhdr, *vh;
+	unsigned int header_len;
+
+	if (!dev)
+		return 0;
+
+	/* In the SOCK_DGRAM scenario, skb data starts at the network
+	 * protocol, which is after the VLAN headers. The outer VLAN
+	 * header is at the hard_header_len offset in non-variable
+	 * length link layer headers. If it's a VLAN device, the
+	 * min_header_len should be used to exclude the VLAN header
+	 * size.
+	 */
+	if (dev->min_header_len == dev->hard_header_len)
+		header_len = dev->hard_header_len;
+	else if (is_vlan_dev(dev))
+		header_len = dev->min_header_len;
+	else
+		return 0;
+
+	vh = skb_header_pointer(skb, skb_mac_offset(skb) + header_len,
+				sizeof(vhdr), &vhdr);
+	if (unlikely(!vh))
+		return 0;
+
+	return ntohs(vh->h_vlan_TCI);
+}
+
+static __be16 vlan_get_protocol_dgram(const struct sk_buff *skb)
+{
+	__be16 proto = skb->protocol;
+
+	if (unlikely(eth_type_vlan(proto)))
+		proto = __vlan_get_protocol_offset(skb, proto,
+						   skb_mac_offset(skb), NULL);
+
+	return proto;
+}
+
 static void prb_del_retire_blk_timer(struct tpacket_kbdq_core *pkc)
 {
 	del_timer_sync(&pkc->retire_blk_timer);
@@ -969,10 +1015,16 @@
 static void prb_fill_vlan_info(struct tpacket_kbdq_core *pkc,
 			struct tpacket3_hdr *ppd)
 {
+	struct packet_sock *po = container_of(pkc, struct packet_sock, rx_ring.prb_bdqc);
+
 	if (skb_vlan_tag_present(pkc->skb)) {
 		ppd->hv1.tp_vlan_tci = skb_vlan_tag_get(pkc->skb);
 		ppd->hv1.tp_vlan_tpid = ntohs(pkc->skb->vlan_proto);
 		ppd->tp_status = TP_STATUS_VLAN_VALID | TP_STATUS_VLAN_TPID_VALID;
+	} else if (unlikely(po->sk.sk_type == SOCK_DGRAM && eth_type_vlan(pkc->skb->protocol))) {
+		ppd->hv1.tp_vlan_tci = vlan_get_tci(pkc->skb, pkc->skb->dev);
+		ppd->hv1.tp_vlan_tpid = ntohs(pkc->skb->protocol);
+		ppd->tp_status = TP_STATUS_VLAN_VALID | TP_STATUS_VLAN_TPID_VALID;
 	} else {
 		ppd->hv1.tp_vlan_tci = 0;
 		ppd->hv1.tp_vlan_tpid = 0;
@@ -1738,6 +1790,7 @@
 		match->prot_hook.dev = po->prot_hook.dev;
 		match->prot_hook.func = packet_rcv_fanout;
 		match->prot_hook.af_packet_priv = match;
+		match->prot_hook.af_packet_net = read_pnet(&match->net);
 		match->prot_hook.id_match = match_fanout_group;
 		match->max_num_members = args->max_num_members;
 		list_add(&match->list, &fanout_list);
@@ -1752,7 +1805,10 @@
 		err = -ENOSPC;
 		if (refcount_read(&match->sk_ref) < match->max_num_members) {
 			__dev_remove_pack(&po->prot_hook);
-			po->fanout = match;
+
+			/* Paired with packet_setsockopt(PACKET_FANOUT_DATA) */
+			WRITE_ONCE(po->fanout, match);
+
 			po->rollover = rollover;
 			rollover = NULL;
 			refcount_set(&match->sk_ref, refcount_read(&match->sk_ref) + 1);
@@ -1865,7 +1921,7 @@
 	 */
 
 	spkt->spkt_family = dev->type;
-	strlcpy(spkt->spkt_device, dev->name, sizeof(spkt->spkt_device));
+	strscpy(spkt->spkt_device, dev->name, sizeof(spkt->spkt_device));
 	spkt->spkt_protocol = skb->protocol;
 
 	/*
@@ -1884,12 +1940,20 @@
 
 static void packet_parse_headers(struct sk_buff *skb, struct socket *sock)
 {
+	int depth;
+
 	if ((!skb->protocol || skb->protocol == htons(ETH_P_ALL)) &&
 	    sock->type == SOCK_RAW) {
 		skb_reset_mac_header(skb);
 		skb->protocol = dev_parse_header_protocol(skb);
 	}
 
+	/* Move network header to the right position for VLAN tagged packets */
+	if (likely(skb->dev->type == ARPHRD_ETHER) &&
+	    eth_type_vlan(skb->protocol) &&
+	    vlan_get_protocol_and_depth(skb, skb->protocol, &depth) != 0)
+		skb_set_network_header(skb, depth);
+
 	skb_probe_transport_header(skb);
 }
 
@@ -1984,7 +2048,7 @@
 		goto retry;
 	}
 
-	if (!dev_validate_header(dev, skb->data, len)) {
+	if (!dev_validate_header(dev, skb->data, len) || !skb->len) {
 		err = -EINVAL;
 		goto out_unlock;
 	}
@@ -2134,7 +2198,7 @@
 	sll = &PACKET_SKB_CB(skb)->sa.ll;
 	sll->sll_hatype = dev->type;
 	sll->sll_pkttype = skb->pkt_type;
-	if (unlikely(po->origdev))
+	if (unlikely(packet_sock_flag(po, PACKET_SOCK_ORIGDEV)))
 		sll->sll_ifindex = orig_dev->ifindex;
 	else
 		sll->sll_ifindex = dev->ifindex;
@@ -2242,8 +2306,7 @@
 	if (skb->ip_summed == CHECKSUM_PARTIAL)
 		status |= TP_STATUS_CSUMNOTREADY;
 	else if (skb->pkt_type != PACKET_OUTGOING &&
-		 (skb->ip_summed == CHECKSUM_COMPLETE ||
-		  skb_csum_unnecessary(skb)))
+		 skb_csum_unnecessary(skb))
 		status |= TP_STATUS_CSUM_VALID;
 
 	if (snaplen > res)
@@ -2277,8 +2340,11 @@
 					copy_skb = skb_get(skb);
 					skb_head = skb->data;
 				}
-				if (copy_skb)
+				if (copy_skb) {
+					memset(&PACKET_SKB_CB(copy_skb)->sa.ll, 0,
+					       sizeof(PACKET_SKB_CB(copy_skb)->sa.ll));
 					skb_set_owner_r(copy_skb, sk);
+				}
 			}
 			snaplen = po->rx_ring.frame_size - macoff;
 			if ((int)snaplen < 0) {
@@ -2374,6 +2440,10 @@
 			h.h2->tp_vlan_tci = skb_vlan_tag_get(skb);
 			h.h2->tp_vlan_tpid = ntohs(skb->vlan_proto);
 			status |= TP_STATUS_VLAN_VALID | TP_STATUS_VLAN_TPID_VALID;
+		} else if (unlikely(sk->sk_type == SOCK_DGRAM && eth_type_vlan(skb->protocol))) {
+			h.h2->tp_vlan_tci = vlan_get_tci(skb, skb->dev);
+			h.h2->tp_vlan_tpid = ntohs(skb->protocol);
+			status |= TP_STATUS_VLAN_VALID | TP_STATUS_VLAN_TPID_VALID;
 		} else {
 			h.h2->tp_vlan_tci = 0;
 			h.h2->tp_vlan_tpid = 0;
@@ -2403,9 +2473,10 @@
 	sll->sll_halen = dev_parse_header(skb, sll->sll_addr);
 	sll->sll_family = AF_PACKET;
 	sll->sll_hatype = dev->type;
-	sll->sll_protocol = skb->protocol;
+	sll->sll_protocol = (sk->sk_type == SOCK_DGRAM) ?
+		vlan_get_protocol_dgram(skb) : skb->protocol;
 	sll->sll_pkttype = skb->pkt_type;
-	if (unlikely(po->origdev))
+	if (unlikely(packet_sock_flag(po, PACKET_SOCK_ORIGDEV)))
 		sll->sll_ifindex = orig_dev->ifindex;
 	else
 		sll->sll_ifindex = dev->ifindex;
@@ -2471,8 +2542,7 @@
 		ts = __packet_set_timestamp(po, ph, skb);
 		__packet_set_status(po, ph, TP_STATUS_AVAILABLE | ts);
 
-		if (!packet_read_pending(&po->tx_ring))
-			complete(&po->skb_completion);
+		complete(&po->skb_completion);
 	}
 
 	sock_wfree(skb);
@@ -2812,9 +2882,11 @@
 		packet_inc_pending(&po->tx_ring);
 
 		status = TP_STATUS_SEND_REQUEST;
-		err = po->xmit(skb);
-		if (unlikely(err > 0)) {
-			err = net_xmit_errno(err);
+		/* Paired with WRITE_ONCE() in packet_setsockopt() */
+		err = READ_ONCE(po->xmit)(skb);
+		if (unlikely(err != 0)) {
+			if (err > 0)
+				err = net_xmit_errno(err);
 			if (err && __packet_get_status(po, ph) ==
 				   TP_STATUS_AVAILABLE) {
 				/* skb was destructed already */
@@ -2981,8 +3053,8 @@
 	if (err)
 		goto out_free;
 
-	if (sock->type == SOCK_RAW &&
-	    !dev_validate_header(dev, skb->data, len)) {
+	if ((sock->type == SOCK_RAW &&
+	     !dev_validate_header(dev, skb->data, len)) || !skb->len) {
 		err = -EINVAL;
 		goto out_free;
 	}
@@ -3001,6 +3073,11 @@
 	skb->mark = sockc.mark;
 	skb->tstamp = sockc.transmit_time;
 
+	if (unlikely(extra_len == 4))
+		skb->no_fcs = 1;
+
+	packet_parse_headers(skb, sock);
+
 	if (has_vnet_hdr) {
 		err = virtio_net_hdr_to_skb(skb, &vnet_hdr, vio_le());
 		if (err)
@@ -3009,14 +3086,14 @@
 		virtio_net_hdr_set_proto(skb, &vnet_hdr);
 	}
 
-	packet_parse_headers(skb, sock);
-
-	if (unlikely(extra_len == 4))
-		skb->no_fcs = 1;
-
-	err = po->xmit(skb);
-	if (err > 0 && (err = net_xmit_errno(err)) != 0)
-		goto out_unlock;
+	/* Paired with WRITE_ONCE() in packet_setsockopt() */
+	err = READ_ONCE(po->xmit)(skb);
+	if (unlikely(err != 0)) {
+		if (err > 0)
+			err = net_xmit_errno(err);
+		if (err)
+			goto out_unlock;
+	}
 
 	dev_put(dev);
 
@@ -3067,9 +3144,7 @@
 	sk_del_node_init_rcu(sk);
 	mutex_unlock(&net->packet.sklist_lock);
 
-	preempt_disable();
 	sock_prot_inuse_add(net, sk->sk_prot, -1);
-	preempt_enable();
 
 	spin_lock(&po->bind_lock);
 	unregister_prot_hook(sk, false);
@@ -3137,6 +3212,9 @@
 
 	lock_sock(sk);
 	spin_lock(&po->bind_lock);
+	if (!proto)
+		proto = po->num;
+
 	rcu_read_lock();
 
 	if (po->fanout) {
@@ -3223,7 +3301,7 @@
 			    int addr_len)
 {
 	struct sock *sk = sock->sk;
-	char name[sizeof(uaddr->sa_data) + 1];
+	char name[sizeof(uaddr->sa_data_min) + 1];
 
 	/*
 	 *	Check legality
@@ -3234,10 +3312,10 @@
 	/* uaddr->sa_data comes from the userspace, it's not guaranteed to be
 	 * zero-terminated.
 	 */
-	memcpy(name, uaddr->sa_data, sizeof(uaddr->sa_data));
-	name[sizeof(uaddr->sa_data)] = 0;
+	memcpy(name, uaddr->sa_data, sizeof(uaddr->sa_data_min));
+	name[sizeof(uaddr->sa_data_min)] = 0;
 
-	return packet_do_bind(sk, name, 0, pkt_sk(sk)->num);
+	return packet_do_bind(sk, name, 0, 0);
 }
 
 static int packet_bind(struct socket *sock, struct sockaddr *uaddr, int addr_len)
@@ -3254,8 +3332,7 @@
 	if (sll->sll_family != AF_PACKET)
 		return -EINVAL;
 
-	return packet_do_bind(sk, NULL, sll->sll_ifindex,
-			      sll->sll_protocol ? : pkt_sk(sk)->num);
+	return packet_do_bind(sk, NULL, sll->sll_ifindex, sll->sll_protocol);
 }
 
 static struct proto packet_proto = {
@@ -3293,18 +3370,18 @@
 	if (sock->type == SOCK_PACKET)
 		sock->ops = &packet_ops_spkt;
 
+	po = pkt_sk(sk);
+	err = packet_alloc_pending(po);
+	if (err)
+		goto out_sk_free;
+
 	sock_init_data(sock, sk);
 
-	po = pkt_sk(sk);
 	init_completion(&po->skb_completion);
 	sk->sk_family = PF_PACKET;
 	po->num = proto;
 	po->xmit = dev_queue_xmit;
 
-	err = packet_alloc_pending(po);
-	if (err)
-		goto out2;
-
 	packet_cached_dev_reset(po);
 
 	sk->sk_destruct = packet_sock_destruct;
@@ -3323,6 +3400,7 @@
 		po->prot_hook.func = packet_rcv_spkt;
 
 	po->prot_hook.af_packet_priv = sk;
+	po->prot_hook.af_packet_net = sock_net(sk);
 
 	if (proto) {
 		po->prot_hook.type = proto;
@@ -3333,12 +3411,10 @@
 	sk_add_node_tail_rcu(sk, &net->packet.sklist);
 	mutex_unlock(&net->packet.sklist_lock);
 
-	preempt_disable();
 	sock_prot_inuse_add(net, &packet_proto, 1);
-	preempt_enable();
 
 	return 0;
-out2:
+out_sk_free:
 	sk_free(sk);
 out:
 	return err;
@@ -3423,12 +3499,15 @@
 		/* Original length was stored in sockaddr_ll fields */
 		origlen = PACKET_SKB_CB(skb)->sa.origlen;
 		sll->sll_family = AF_PACKET;
-		sll->sll_protocol = skb->protocol;
+		sll->sll_protocol = (sock->type == SOCK_DGRAM) ?
+			vlan_get_protocol_dgram(skb) : skb->protocol;
 	}
 
 	sock_recv_ts_and_drops(msg, sk, skb);
 
 	if (msg->msg_name) {
+		const size_t max_len = min(sizeof(skb->cb),
+					   sizeof(struct sockaddr_storage));
 		int copy_len;
 
 		/* If the address length field is there to be filled
@@ -3451,18 +3530,21 @@
 				msg->msg_namelen = sizeof(struct sockaddr_ll);
 			}
 		}
+		if (WARN_ON_ONCE(copy_len > max_len)) {
+			copy_len = max_len;
+			msg->msg_namelen = copy_len;
+		}
 		memcpy(msg->msg_name, &PACKET_SKB_CB(skb)->sa, copy_len);
 	}
 
-	if (pkt_sk(sk)->auxdata) {
+	if (packet_sock_flag(pkt_sk(sk), PACKET_SOCK_AUXDATA)) {
 		struct tpacket_auxdata aux;
 
 		aux.tp_status = TP_STATUS_USER;
 		if (skb->ip_summed == CHECKSUM_PARTIAL)
 			aux.tp_status |= TP_STATUS_CSUMNOTREADY;
 		else if (skb->pkt_type != PACKET_OUTGOING &&
-			 (skb->ip_summed == CHECKSUM_COMPLETE ||
-			  skb_csum_unnecessary(skb)))
+			 skb_csum_unnecessary(skb))
 			aux.tp_status |= TP_STATUS_CSUM_VALID;
 
 		aux.tp_len = origlen;
@@ -3473,6 +3555,21 @@
 			aux.tp_vlan_tci = skb_vlan_tag_get(skb);
 			aux.tp_vlan_tpid = ntohs(skb->vlan_proto);
 			aux.tp_status |= TP_STATUS_VLAN_VALID | TP_STATUS_VLAN_TPID_VALID;
+		} else if (unlikely(sock->type == SOCK_DGRAM && eth_type_vlan(skb->protocol))) {
+			struct sockaddr_ll *sll = &PACKET_SKB_CB(skb)->sa.ll;
+			struct net_device *dev;
+
+			rcu_read_lock();
+			dev = dev_get_by_index_rcu(sock_net(sk), sll->sll_ifindex);
+			if (dev) {
+				aux.tp_vlan_tci = vlan_get_tci(skb, dev);
+				aux.tp_vlan_tpid = ntohs(skb->protocol);
+				aux.tp_status |= TP_STATUS_VLAN_VALID | TP_STATUS_VLAN_TPID_VALID;
+			} else {
+				aux.tp_vlan_tci = 0;
+				aux.tp_vlan_tpid = 0;
+			}
+			rcu_read_unlock();
 		} else {
 			aux.tp_vlan_tci = 0;
 			aux.tp_vlan_tpid = 0;
@@ -3502,11 +3599,11 @@
 		return -EOPNOTSUPP;
 
 	uaddr->sa_family = AF_PACKET;
-	memset(uaddr->sa_data, 0, sizeof(uaddr->sa_data));
+	memset(uaddr->sa_data, 0, sizeof(uaddr->sa_data_min));
 	rcu_read_lock();
 	dev = dev_get_by_index_rcu(sock_net(sk), READ_ONCE(pkt_sk(sk)->ifindex));
 	if (dev)
-		strlcpy(uaddr->sa_data, dev->name, sizeof(uaddr->sa_data));
+		strscpy(uaddr->sa_data, dev->name, sizeof(uaddr->sa_data_min));
 	rcu_read_unlock();
 
 	return sizeof(*uaddr);
@@ -3728,28 +3825,30 @@
 	case PACKET_TX_RING:
 	{
 		union tpacket_req_u req_u;
-		int len;
 
+		ret = -EINVAL;
 		lock_sock(sk);
 		switch (po->tp_version) {
 		case TPACKET_V1:
 		case TPACKET_V2:
-			len = sizeof(req_u.req);
+			if (optlen < sizeof(req_u.req))
+				break;
+			ret = copy_from_sockptr(&req_u.req, optval,
+						sizeof(req_u.req)) ?
+						-EINVAL : 0;
 			break;
 		case TPACKET_V3:
 		default:
-			len = sizeof(req_u.req3);
+			if (optlen < sizeof(req_u.req3))
+				break;
+			ret = copy_from_sockptr(&req_u.req3, optval,
+						sizeof(req_u.req3)) ?
+						-EINVAL : 0;
 			break;
 		}
-		if (optlen < len) {
-			ret = -EINVAL;
-		} else {
-			if (copy_from_sockptr(&req_u.req, optval, len))
-				ret = -EFAULT;
-			else
-				ret = packet_set_ring(sk, &req_u, 0,
-						    optname == PACKET_TX_RING);
-		}
+		if (!ret)
+			ret = packet_set_ring(sk, &req_u, 0,
+					      optname == PACKET_TX_RING);
 		release_sock(sk);
 		return ret;
 	}
@@ -3839,9 +3938,7 @@
 		if (copy_from_sockptr(&val, optval, sizeof(val)))
 			return -EFAULT;
 
-		lock_sock(sk);
-		po->auxdata = !!val;
-		release_sock(sk);
+		packet_sock_flag_set(po, PACKET_SOCK_AUXDATA, val);
 		return 0;
 	}
 	case PACKET_ORIGDEV:
@@ -3853,9 +3950,7 @@
 		if (copy_from_sockptr(&val, optval, sizeof(val)))
 			return -EFAULT;
 
-		lock_sock(sk);
-		po->origdev = !!val;
-		release_sock(sk);
+		packet_sock_flag_set(po, PACKET_SOCK_ORIGDEV, val);
 		return 0;
 	}
 	case PACKET_VNET_HDR:
@@ -3904,7 +3999,8 @@
 	}
 	case PACKET_FANOUT_DATA:
 	{
-		if (!po->fanout)
+		/* Paired with the WRITE_ONCE() in fanout_add() */
+		if (!READ_ONCE(po->fanout))
 			return -EINVAL;
 
 		return fanout_set_data(po, optval, optlen);
@@ -3920,7 +4016,7 @@
 		if (val < 0 || val > 1)
 			return -EINVAL;
 
-		po->prot_hook.ignore_outgoing = !!val;
+		WRITE_ONCE(po->prot_hook.ignore_outgoing, !!val);
 		return 0;
 	}
 	case PACKET_TX_HAS_OFF:
@@ -3948,7 +4044,8 @@
 		if (copy_from_sockptr(&val, optval, sizeof(val)))
 			return -EFAULT;
 
-		po->xmit = val ? packet_direct_xmit : dev_queue_xmit;
+		/* Paired with all lockless reads of po->xmit */
+		WRITE_ONCE(po->xmit, val ? packet_direct_xmit : dev_queue_xmit);
 		return 0;
 	}
 	default:
@@ -3999,10 +4096,10 @@
 
 		break;
 	case PACKET_AUXDATA:
-		val = po->auxdata;
+		val = packet_sock_flag(po, PACKET_SOCK_AUXDATA);
 		break;
 	case PACKET_ORIGDEV:
-		val = po->origdev;
+		val = packet_sock_flag(po, PACKET_SOCK_ORIGDEV);
 		break;
 	case PACKET_VNET_HDR:
 		val = po->has_vnet_hdr;
@@ -4048,7 +4145,7 @@
 		       0);
 		break;
 	case PACKET_IGNORE_OUTGOING:
-		val = po->prot_hook.ignore_outgoing;
+		val = READ_ONCE(po->prot_hook.ignore_outgoing);
 		break;
 	case PACKET_ROLLOVER_STATS:
 		if (!po->rollover)
@@ -4212,7 +4309,7 @@
 	struct sock *sk = sock->sk;
 
 	if (sk)
-		atomic_inc(&pkt_sk(sk)->mapped);
+		atomic_long_inc(&pkt_sk(sk)->mapped);
 }
 
 static void packet_mm_close(struct vm_area_struct *vma)
@@ -4222,7 +4319,7 @@
 	struct sock *sk = sock->sk;
 
 	if (sk)
-		atomic_dec(&pkt_sk(sk)->mapped);
+		atomic_long_dec(&pkt_sk(sk)->mapped);
 }
 
 static const struct vm_operations_struct packet_mmap_ops = {
@@ -4317,7 +4414,7 @@
 
 	err = -EBUSY;
 	if (!closing) {
-		if (atomic_read(&po->mapped))
+		if (atomic_long_read(&po->mapped))
 			goto out;
 		if (packet_read_pending(rb))
 			goto out;
@@ -4420,7 +4517,7 @@
 
 	err = -EBUSY;
 	mutex_lock(&po->pg_vec_lock);
-	if (closing || atomic_read(&po->mapped) == 0) {
+	if (closing || atomic_long_read(&po->mapped) == 0) {
 		err = 0;
 		spin_lock_bh(&rb_queue->lock);
 		swap(rb->pg_vec, pg_vec);
@@ -4438,9 +4535,9 @@
 		po->prot_hook.func = (po->rx_ring.pg_vec) ?
 						tpacket_rcv : packet_rcv;
 		skb_queue_purge(rb_queue);
-		if (atomic_read(&po->mapped))
-			pr_err("packet_mmap: vma is busy: %d\n",
-			       atomic_read(&po->mapped));
+		if (atomic_long_read(&po->mapped))
+			pr_err("packet_mmap: vma is busy: %ld\n",
+			       atomic_long_read(&po->mapped));
 	}
 	mutex_unlock(&po->pg_vec_lock);
 
@@ -4457,9 +4554,10 @@
 	}
 
 out_free_pg_vec:
-	bitmap_free(rx_owner_map);
-	if (pg_vec)
+	if (pg_vec) {
+		bitmap_free(rx_owner_map);
 		free_pg_vec(pg_vec, order, req->tp_block_nr);
+	}
 out:
 	return err;
 }
@@ -4517,7 +4615,7 @@
 		}
 	}
 
-	atomic_inc(&po->mapped);
+	atomic_long_inc(&po->mapped);
 	vma->vm_ops = &packet_mmap_ops;
 	err = 0;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/packet/diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/packet/diag.c
@@ -23,9 +23,9 @@
 	pinfo.pdi_flags = 0;
 	if (po->running)
 		pinfo.pdi_flags |= PDI_RUNNING;
-	if (po->auxdata)
+	if (packet_sock_flag(po, PACKET_SOCK_AUXDATA))
 		pinfo.pdi_flags |= PDI_AUXDATA;
-	if (po->origdev)
+	if (packet_sock_flag(po, PACKET_SOCK_ORIGDEV))
 		pinfo.pdi_flags |= PDI_ORIGDEV;
 	if (po->has_vnet_hdr)
 		pinfo.pdi_flags |= PDI_VNETHDR;
@@ -143,7 +143,7 @@
 	rp = nlmsg_data(nlh);
 	rp->pdiag_family = AF_PACKET;
 	rp->pdiag_type = sk->sk_type;
-	rp->pdiag_num = ntohs(po->num);
+	rp->pdiag_num = ntohs(READ_ONCE(po->num));
 	rp->pdiag_ino = sk_ino;
 	sock_diag_save_cookie(sk, rp->pdiag_cookie);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/packet/internal.h
+++ linux-xilinx-zynqmp-5.15.0/net/packet/internal.h
@@ -116,10 +116,9 @@
 	int			copy_thresh;
 	spinlock_t		bind_lock;
 	struct mutex		pg_vec_lock;
+	unsigned long		flags;
 	unsigned int		running;	/* bind_lock must be held */
-	unsigned int		auxdata:1,	/* writer must hold sock lock */
-				origdev:1,
-				has_vnet_hdr:1,
+	unsigned int		has_vnet_hdr:1, /* writer must hold sock lock */
 				tp_loss:1,
 				tp_tx_has_off:1;
 	int			pressure;
@@ -127,7 +126,7 @@
 	__be16			num;
 	struct packet_rollover	*rollover;
 	struct packet_mclist	*mclist;
-	atomic_t		mapped;
+	atomic_long_t		mapped;
 	enum tpacket_versions	tp_version;
 	unsigned int		tp_hdrlen;
 	unsigned int		tp_reserve;
@@ -144,4 +143,25 @@
 	return (struct packet_sock *)sk;
 }
 
+enum packet_sock_flags {
+	PACKET_SOCK_ORIGDEV,
+	PACKET_SOCK_AUXDATA,
+};
+
+static inline void packet_sock_flag_set(struct packet_sock *po,
+					enum packet_sock_flags flag,
+					bool val)
+{
+	if (val)
+		set_bit(flag, &po->flags);
+	else
+		clear_bit(flag, &po->flags);
+}
+
+static inline bool packet_sock_flag(const struct packet_sock *po,
+				    enum packet_sock_flags flag)
+{
+	return test_bit(flag, &po->flags);
+}
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/phonet/pep.c
+++ linux-xilinx-zynqmp-5.15.0/net/phonet/pep.c
@@ -868,6 +868,7 @@
 
 	err = pep_accept_conn(newsk, skb);
 	if (err) {
+		__sock_put(sk);
 		sock_put(newsk);
 		newsk = NULL;
 		goto drop;
@@ -946,6 +947,8 @@
 			ret =  -EBUSY;
 		else if (sk->sk_state == TCP_ESTABLISHED)
 			ret = -EISCONN;
+		else if (!pn->pn_sk.sobject)
+			ret = -EADDRNOTAVAIL;
 		else
 			ret = pep_sock_enable(sk, NULL, 0);
 		release_sock(sk);
--- linux-xilinx-zynqmp-5.15.0.orig/net/phonet/pn_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/phonet/pn_netlink.c
@@ -193,7 +193,7 @@
 	struct sk_buff *skb;
 	int err = -ENOBUFS;
 
-	skb = nlmsg_new(NLMSG_ALIGN(sizeof(struct ifaddrmsg)) +
+	skb = nlmsg_new(NLMSG_ALIGN(sizeof(struct rtmsg)) +
 			nla_total_size(1) + nla_total_size(4), GFP_KERNEL);
 	if (skb == NULL)
 		goto errout;
--- linux-xilinx-zynqmp-5.15.0.orig/net/psample/psample.c
+++ linux-xilinx-zynqmp-5.15.0/net/psample/psample.c
@@ -31,7 +31,8 @@
 
 static const struct genl_multicast_group psample_nl_mcgrps[] = {
 	[PSAMPLE_NL_MCGRP_CONFIG] = { .name = PSAMPLE_NL_MCGRP_CONFIG_NAME },
-	[PSAMPLE_NL_MCGRP_SAMPLE] = { .name = PSAMPLE_NL_MCGRP_SAMPLE_NAME },
+	[PSAMPLE_NL_MCGRP_SAMPLE] = { .name = PSAMPLE_NL_MCGRP_SAMPLE_NAME,
+				      .flags = GENL_UNS_ADMIN_PERM },
 };
 
 static struct genl_family psample_nl_family __ro_after_init;
--- linux-xilinx-zynqmp-5.15.0.orig/net/qrtr/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/qrtr/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_QRTR) := qrtr.o ns.o
+obj-$(CONFIG_QRTR) += qrtr.o
+qrtr-y	:= af_qrtr.o ns.o
 
 obj-$(CONFIG_QRTR_SMD) += qrtr-smd.o
 qrtr-smd-y	:= smd.o
--- linux-xilinx-zynqmp-5.15.0.orig/net/qrtr/af_qrtr.c
+++ linux-xilinx-zynqmp-5.15.0/net/qrtr/af_qrtr.c
@@ -0,0 +1,1325 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, Sony Mobile Communications Inc.
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ */
+#include <linux/module.h>
+#include <linux/netlink.h>
+#include <linux/qrtr.h>
+#include <linux/termios.h>	/* For TIOCINQ/OUTQ */
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+
+#include <net/sock.h>
+
+#include "qrtr.h"
+
+#define QRTR_PROTO_VER_1 1
+#define QRTR_PROTO_VER_2 3
+
+/* auto-bind range */
+#define QRTR_MIN_EPH_SOCKET 0x4000
+#define QRTR_MAX_EPH_SOCKET 0x7fff
+#define QRTR_EPH_PORT_RANGE \
+		XA_LIMIT(QRTR_MIN_EPH_SOCKET, QRTR_MAX_EPH_SOCKET)
+
+/**
+ * struct qrtr_hdr_v1 - (I|R)PCrouter packet header version 1
+ * @version: protocol version
+ * @type: packet type; one of QRTR_TYPE_*
+ * @src_node_id: source node
+ * @src_port_id: source port
+ * @confirm_rx: boolean; whether a resume-tx packet should be send in reply
+ * @size: length of packet, excluding this header
+ * @dst_node_id: destination node
+ * @dst_port_id: destination port
+ */
+struct qrtr_hdr_v1 {
+	__le32 version;
+	__le32 type;
+	__le32 src_node_id;
+	__le32 src_port_id;
+	__le32 confirm_rx;
+	__le32 size;
+	__le32 dst_node_id;
+	__le32 dst_port_id;
+} __packed;
+
+/**
+ * struct qrtr_hdr_v2 - (I|R)PCrouter packet header later versions
+ * @version: protocol version
+ * @type: packet type; one of QRTR_TYPE_*
+ * @flags: bitmask of QRTR_FLAGS_*
+ * @optlen: length of optional header data
+ * @size: length of packet, excluding this header and optlen
+ * @src_node_id: source node
+ * @src_port_id: source port
+ * @dst_node_id: destination node
+ * @dst_port_id: destination port
+ */
+struct qrtr_hdr_v2 {
+	u8 version;
+	u8 type;
+	u8 flags;
+	u8 optlen;
+	__le32 size;
+	__le16 src_node_id;
+	__le16 src_port_id;
+	__le16 dst_node_id;
+	__le16 dst_port_id;
+};
+
+#define QRTR_FLAGS_CONFIRM_RX	BIT(0)
+
+struct qrtr_cb {
+	u32 src_node;
+	u32 src_port;
+	u32 dst_node;
+	u32 dst_port;
+
+	u8 type;
+	u8 confirm_rx;
+};
+
+#define QRTR_HDR_MAX_SIZE max_t(size_t, sizeof(struct qrtr_hdr_v1), \
+					sizeof(struct qrtr_hdr_v2))
+
+struct qrtr_sock {
+	/* WARNING: sk must be the first member */
+	struct sock sk;
+	struct sockaddr_qrtr us;
+	struct sockaddr_qrtr peer;
+};
+
+static inline struct qrtr_sock *qrtr_sk(struct sock *sk)
+{
+	BUILD_BUG_ON(offsetof(struct qrtr_sock, sk) != 0);
+	return container_of(sk, struct qrtr_sock, sk);
+}
+
+static unsigned int qrtr_local_nid = 1;
+
+/* for node ids */
+static RADIX_TREE(qrtr_nodes, GFP_ATOMIC);
+static DEFINE_SPINLOCK(qrtr_nodes_lock);
+/* broadcast list */
+static LIST_HEAD(qrtr_all_nodes);
+/* lock for qrtr_all_nodes and node reference */
+static DEFINE_MUTEX(qrtr_node_lock);
+
+/* local port allocation management */
+static DEFINE_XARRAY_ALLOC(qrtr_ports);
+
+/**
+ * struct qrtr_node - endpoint node
+ * @ep_lock: lock for endpoint management and callbacks
+ * @ep: endpoint
+ * @ref: reference count for node
+ * @nid: node id
+ * @qrtr_tx_flow: tree of qrtr_tx_flow, keyed by node << 32 | port
+ * @qrtr_tx_lock: lock for qrtr_tx_flow inserts
+ * @rx_queue: receive queue
+ * @item: list item for broadcast list
+ */
+struct qrtr_node {
+	struct mutex ep_lock;
+	struct qrtr_endpoint *ep;
+	struct kref ref;
+	unsigned int nid;
+
+	struct radix_tree_root qrtr_tx_flow;
+	struct mutex qrtr_tx_lock; /* for qrtr_tx_flow */
+
+	struct sk_buff_head rx_queue;
+	struct list_head item;
+};
+
+/**
+ * struct qrtr_tx_flow - tx flow control
+ * @resume_tx: waiters for a resume tx from the remote
+ * @pending: number of waiting senders
+ * @tx_failed: indicates that a message with confirm_rx flag was lost
+ */
+struct qrtr_tx_flow {
+	struct wait_queue_head resume_tx;
+	int pending;
+	int tx_failed;
+};
+
+#define QRTR_TX_FLOW_HIGH	10
+#define QRTR_TX_FLOW_LOW	5
+
+static int qrtr_local_enqueue(struct qrtr_node *node, struct sk_buff *skb,
+			      int type, struct sockaddr_qrtr *from,
+			      struct sockaddr_qrtr *to);
+static int qrtr_bcast_enqueue(struct qrtr_node *node, struct sk_buff *skb,
+			      int type, struct sockaddr_qrtr *from,
+			      struct sockaddr_qrtr *to);
+static struct qrtr_sock *qrtr_port_lookup(int port);
+static void qrtr_port_put(struct qrtr_sock *ipc);
+
+/* Release node resources and free the node.
+ *
+ * Do not call directly, use qrtr_node_release.  To be used with
+ * kref_put_mutex.  As such, the node mutex is expected to be locked on call.
+ */
+static void __qrtr_node_release(struct kref *kref)
+{
+	struct qrtr_node *node = container_of(kref, struct qrtr_node, ref);
+	struct radix_tree_iter iter;
+	struct qrtr_tx_flow *flow;
+	unsigned long flags;
+	void __rcu **slot;
+
+	spin_lock_irqsave(&qrtr_nodes_lock, flags);
+	/* If the node is a bridge for other nodes, there are possibly
+	 * multiple entries pointing to our released node, delete them all.
+	 */
+	radix_tree_for_each_slot(slot, &qrtr_nodes, &iter, 0) {
+		if (*slot == node)
+			radix_tree_iter_delete(&qrtr_nodes, &iter, slot);
+	}
+	spin_unlock_irqrestore(&qrtr_nodes_lock, flags);
+
+	list_del(&node->item);
+	mutex_unlock(&qrtr_node_lock);
+
+	skb_queue_purge(&node->rx_queue);
+
+	/* Free tx flow counters */
+	radix_tree_for_each_slot(slot, &node->qrtr_tx_flow, &iter, 0) {
+		flow = *slot;
+		radix_tree_iter_delete(&node->qrtr_tx_flow, &iter, slot);
+		kfree(flow);
+	}
+	kfree(node);
+}
+
+/* Increment reference to node. */
+static struct qrtr_node *qrtr_node_acquire(struct qrtr_node *node)
+{
+	if (node)
+		kref_get(&node->ref);
+	return node;
+}
+
+/* Decrement reference to node and release as necessary. */
+static void qrtr_node_release(struct qrtr_node *node)
+{
+	if (!node)
+		return;
+	kref_put_mutex(&node->ref, __qrtr_node_release, &qrtr_node_lock);
+}
+
+/**
+ * qrtr_tx_resume() - reset flow control counter
+ * @node:	qrtr_node that the QRTR_TYPE_RESUME_TX packet arrived on
+ * @skb:	resume_tx packet
+ */
+static void qrtr_tx_resume(struct qrtr_node *node, struct sk_buff *skb)
+{
+	struct qrtr_ctrl_pkt *pkt = (struct qrtr_ctrl_pkt *)skb->data;
+	u64 remote_node = le32_to_cpu(pkt->client.node);
+	u32 remote_port = le32_to_cpu(pkt->client.port);
+	struct qrtr_tx_flow *flow;
+	unsigned long key;
+
+	key = remote_node << 32 | remote_port;
+
+	rcu_read_lock();
+	flow = radix_tree_lookup(&node->qrtr_tx_flow, key);
+	rcu_read_unlock();
+	if (flow) {
+		spin_lock(&flow->resume_tx.lock);
+		flow->pending = 0;
+		spin_unlock(&flow->resume_tx.lock);
+		wake_up_interruptible_all(&flow->resume_tx);
+	}
+
+	consume_skb(skb);
+}
+
+/**
+ * qrtr_tx_wait() - flow control for outgoing packets
+ * @node:	qrtr_node that the packet is to be send to
+ * @dest_node:	node id of the destination
+ * @dest_port:	port number of the destination
+ * @type:	type of message
+ *
+ * The flow control scheme is based around the low and high "watermarks". When
+ * the low watermark is passed the confirm_rx flag is set on the outgoing
+ * message, which will trigger the remote to send a control message of the type
+ * QRTR_TYPE_RESUME_TX to reset the counter. If the high watermark is hit
+ * further transmision should be paused.
+ *
+ * Return: 1 if confirm_rx should be set, 0 otherwise or errno failure
+ */
+static int qrtr_tx_wait(struct qrtr_node *node, int dest_node, int dest_port,
+			int type)
+{
+	unsigned long key = (u64)dest_node << 32 | dest_port;
+	struct qrtr_tx_flow *flow;
+	int confirm_rx = 0;
+	int ret;
+
+	/* Never set confirm_rx on non-data packets */
+	if (type != QRTR_TYPE_DATA)
+		return 0;
+
+	mutex_lock(&node->qrtr_tx_lock);
+	flow = radix_tree_lookup(&node->qrtr_tx_flow, key);
+	if (!flow) {
+		flow = kzalloc(sizeof(*flow), GFP_KERNEL);
+		if (flow) {
+			init_waitqueue_head(&flow->resume_tx);
+			if (radix_tree_insert(&node->qrtr_tx_flow, key, flow)) {
+				kfree(flow);
+				flow = NULL;
+			}
+		}
+	}
+	mutex_unlock(&node->qrtr_tx_lock);
+
+	/* Set confirm_rx if we where unable to find and allocate a flow */
+	if (!flow)
+		return 1;
+
+	spin_lock_irq(&flow->resume_tx.lock);
+	ret = wait_event_interruptible_locked_irq(flow->resume_tx,
+						  flow->pending < QRTR_TX_FLOW_HIGH ||
+						  flow->tx_failed ||
+						  !node->ep);
+	if (ret < 0) {
+		confirm_rx = ret;
+	} else if (!node->ep) {
+		confirm_rx = -EPIPE;
+	} else if (flow->tx_failed) {
+		flow->tx_failed = 0;
+		confirm_rx = 1;
+	} else {
+		flow->pending++;
+		confirm_rx = flow->pending == QRTR_TX_FLOW_LOW;
+	}
+	spin_unlock_irq(&flow->resume_tx.lock);
+
+	return confirm_rx;
+}
+
+/**
+ * qrtr_tx_flow_failed() - flag that tx of confirm_rx flagged messages failed
+ * @node:	qrtr_node that the packet is to be send to
+ * @dest_node:	node id of the destination
+ * @dest_port:	port number of the destination
+ *
+ * Signal that the transmission of a message with confirm_rx flag failed. The
+ * flow's "pending" counter will keep incrementing towards QRTR_TX_FLOW_HIGH,
+ * at which point transmission would stall forever waiting for the resume TX
+ * message associated with the dropped confirm_rx message.
+ * Work around this by marking the flow as having a failed transmission and
+ * cause the next transmission attempt to be sent with the confirm_rx.
+ */
+static void qrtr_tx_flow_failed(struct qrtr_node *node, int dest_node,
+				int dest_port)
+{
+	unsigned long key = (u64)dest_node << 32 | dest_port;
+	struct qrtr_tx_flow *flow;
+
+	rcu_read_lock();
+	flow = radix_tree_lookup(&node->qrtr_tx_flow, key);
+	rcu_read_unlock();
+	if (flow) {
+		spin_lock_irq(&flow->resume_tx.lock);
+		flow->tx_failed = 1;
+		spin_unlock_irq(&flow->resume_tx.lock);
+	}
+}
+
+/* Pass an outgoing packet socket buffer to the endpoint driver. */
+static int qrtr_node_enqueue(struct qrtr_node *node, struct sk_buff *skb,
+			     int type, struct sockaddr_qrtr *from,
+			     struct sockaddr_qrtr *to)
+{
+	struct qrtr_hdr_v1 *hdr;
+	size_t len = skb->len;
+	int rc, confirm_rx;
+
+	confirm_rx = qrtr_tx_wait(node, to->sq_node, to->sq_port, type);
+	if (confirm_rx < 0) {
+		kfree_skb(skb);
+		return confirm_rx;
+	}
+
+	hdr = skb_push(skb, sizeof(*hdr));
+	hdr->version = cpu_to_le32(QRTR_PROTO_VER_1);
+	hdr->type = cpu_to_le32(type);
+	hdr->src_node_id = cpu_to_le32(from->sq_node);
+	hdr->src_port_id = cpu_to_le32(from->sq_port);
+	if (to->sq_port == QRTR_PORT_CTRL) {
+		hdr->dst_node_id = cpu_to_le32(node->nid);
+		hdr->dst_port_id = cpu_to_le32(QRTR_PORT_CTRL);
+	} else {
+		hdr->dst_node_id = cpu_to_le32(to->sq_node);
+		hdr->dst_port_id = cpu_to_le32(to->sq_port);
+	}
+
+	hdr->size = cpu_to_le32(len);
+	hdr->confirm_rx = !!confirm_rx;
+
+	rc = skb_put_padto(skb, ALIGN(len, 4) + sizeof(*hdr));
+
+	if (!rc) {
+		mutex_lock(&node->ep_lock);
+		rc = -ENODEV;
+		if (node->ep)
+			rc = node->ep->xmit(node->ep, skb);
+		else
+			kfree_skb(skb);
+		mutex_unlock(&node->ep_lock);
+	}
+	/* Need to ensure that a subsequent message carries the otherwise lost
+	 * confirm_rx flag if we dropped this one */
+	if (rc && confirm_rx)
+		qrtr_tx_flow_failed(node, to->sq_node, to->sq_port);
+
+	return rc;
+}
+
+/* Lookup node by id.
+ *
+ * callers must release with qrtr_node_release()
+ */
+static struct qrtr_node *qrtr_node_lookup(unsigned int nid)
+{
+	struct qrtr_node *node;
+	unsigned long flags;
+
+	mutex_lock(&qrtr_node_lock);
+	spin_lock_irqsave(&qrtr_nodes_lock, flags);
+	node = radix_tree_lookup(&qrtr_nodes, nid);
+	node = qrtr_node_acquire(node);
+	spin_unlock_irqrestore(&qrtr_nodes_lock, flags);
+	mutex_unlock(&qrtr_node_lock);
+
+	return node;
+}
+
+/* Assign node id to node.
+ *
+ * This is mostly useful for automatic node id assignment, based on
+ * the source id in the incoming packet.
+ */
+static void qrtr_node_assign(struct qrtr_node *node, unsigned int nid)
+{
+	unsigned long flags;
+
+	if (nid == QRTR_EP_NID_AUTO)
+		return;
+
+	spin_lock_irqsave(&qrtr_nodes_lock, flags);
+	radix_tree_insert(&qrtr_nodes, nid, node);
+	if (node->nid == QRTR_EP_NID_AUTO)
+		node->nid = nid;
+	spin_unlock_irqrestore(&qrtr_nodes_lock, flags);
+}
+
+/**
+ * qrtr_endpoint_post() - post incoming data
+ * @ep: endpoint handle
+ * @data: data pointer
+ * @len: size of data in bytes
+ *
+ * Return: 0 on success; negative error code on failure
+ */
+int qrtr_endpoint_post(struct qrtr_endpoint *ep, const void *data, size_t len)
+{
+	struct qrtr_node *node = ep->node;
+	const struct qrtr_hdr_v1 *v1;
+	const struct qrtr_hdr_v2 *v2;
+	struct qrtr_sock *ipc;
+	struct sk_buff *skb;
+	struct qrtr_cb *cb;
+	size_t size;
+	unsigned int ver;
+	size_t hdrlen;
+
+	if (len == 0 || len & 3)
+		return -EINVAL;
+
+	skb = __netdev_alloc_skb(NULL, len, GFP_ATOMIC | __GFP_NOWARN);
+	if (!skb)
+		return -ENOMEM;
+
+	cb = (struct qrtr_cb *)skb->cb;
+
+	/* Version field in v1 is little endian, so this works for both cases */
+	ver = *(u8*)data;
+
+	switch (ver) {
+	case QRTR_PROTO_VER_1:
+		if (len < sizeof(*v1))
+			goto err;
+		v1 = data;
+		hdrlen = sizeof(*v1);
+
+		cb->type = le32_to_cpu(v1->type);
+		cb->src_node = le32_to_cpu(v1->src_node_id);
+		cb->src_port = le32_to_cpu(v1->src_port_id);
+		cb->confirm_rx = !!v1->confirm_rx;
+		cb->dst_node = le32_to_cpu(v1->dst_node_id);
+		cb->dst_port = le32_to_cpu(v1->dst_port_id);
+
+		size = le32_to_cpu(v1->size);
+		break;
+	case QRTR_PROTO_VER_2:
+		if (len < sizeof(*v2))
+			goto err;
+		v2 = data;
+		hdrlen = sizeof(*v2) + v2->optlen;
+
+		cb->type = v2->type;
+		cb->confirm_rx = !!(v2->flags & QRTR_FLAGS_CONFIRM_RX);
+		cb->src_node = le16_to_cpu(v2->src_node_id);
+		cb->src_port = le16_to_cpu(v2->src_port_id);
+		cb->dst_node = le16_to_cpu(v2->dst_node_id);
+		cb->dst_port = le16_to_cpu(v2->dst_port_id);
+
+		if (cb->src_port == (u16)QRTR_PORT_CTRL)
+			cb->src_port = QRTR_PORT_CTRL;
+		if (cb->dst_port == (u16)QRTR_PORT_CTRL)
+			cb->dst_port = QRTR_PORT_CTRL;
+
+		size = le32_to_cpu(v2->size);
+		break;
+	default:
+		pr_err("qrtr: Invalid version %d\n", ver);
+		goto err;
+	}
+
+	if (!size || len != ALIGN(size, 4) + hdrlen)
+		goto err;
+
+	if ((cb->type == QRTR_TYPE_NEW_SERVER ||
+	     cb->type == QRTR_TYPE_RESUME_TX) &&
+	    size < sizeof(struct qrtr_ctrl_pkt))
+		goto err;
+
+	if (cb->dst_port != QRTR_PORT_CTRL && cb->type != QRTR_TYPE_DATA &&
+	    cb->type != QRTR_TYPE_RESUME_TX)
+		goto err;
+
+	skb_put_data(skb, data + hdrlen, size);
+
+	qrtr_node_assign(node, cb->src_node);
+
+	if (cb->type == QRTR_TYPE_NEW_SERVER) {
+		/* Remote node endpoint can bridge other distant nodes */
+		const struct qrtr_ctrl_pkt *pkt;
+
+		pkt = data + hdrlen;
+		qrtr_node_assign(node, le32_to_cpu(pkt->server.node));
+	}
+
+	if (cb->type == QRTR_TYPE_RESUME_TX) {
+		qrtr_tx_resume(node, skb);
+	} else {
+		ipc = qrtr_port_lookup(cb->dst_port);
+		if (!ipc)
+			goto err;
+
+		if (sock_queue_rcv_skb(&ipc->sk, skb)) {
+			qrtr_port_put(ipc);
+			goto err;
+		}
+
+		qrtr_port_put(ipc);
+	}
+
+	return 0;
+
+err:
+	kfree_skb(skb);
+	return -EINVAL;
+
+}
+EXPORT_SYMBOL_GPL(qrtr_endpoint_post);
+
+/**
+ * qrtr_alloc_ctrl_packet() - allocate control packet skb
+ * @pkt: reference to qrtr_ctrl_pkt pointer
+ * @flags: the type of memory to allocate
+ *
+ * Returns newly allocated sk_buff, or NULL on failure
+ *
+ * This function allocates a sk_buff large enough to carry a qrtr_ctrl_pkt and
+ * on success returns a reference to the control packet in @pkt.
+ */
+static struct sk_buff *qrtr_alloc_ctrl_packet(struct qrtr_ctrl_pkt **pkt,
+					      gfp_t flags)
+{
+	const int pkt_len = sizeof(struct qrtr_ctrl_pkt);
+	struct sk_buff *skb;
+
+	skb = alloc_skb(QRTR_HDR_MAX_SIZE + pkt_len, flags);
+	if (!skb)
+		return NULL;
+
+	skb_reserve(skb, QRTR_HDR_MAX_SIZE);
+	*pkt = skb_put_zero(skb, pkt_len);
+
+	return skb;
+}
+
+/**
+ * qrtr_endpoint_register() - register a new endpoint
+ * @ep: endpoint to register
+ * @nid: desired node id; may be QRTR_EP_NID_AUTO for auto-assignment
+ * Return: 0 on success; negative error code on failure
+ *
+ * The specified endpoint must have the xmit function pointer set on call.
+ */
+int qrtr_endpoint_register(struct qrtr_endpoint *ep, unsigned int nid)
+{
+	struct qrtr_node *node;
+
+	if (!ep || !ep->xmit)
+		return -EINVAL;
+
+	node = kzalloc(sizeof(*node), GFP_KERNEL);
+	if (!node)
+		return -ENOMEM;
+
+	kref_init(&node->ref);
+	mutex_init(&node->ep_lock);
+	skb_queue_head_init(&node->rx_queue);
+	node->nid = QRTR_EP_NID_AUTO;
+	node->ep = ep;
+
+	INIT_RADIX_TREE(&node->qrtr_tx_flow, GFP_KERNEL);
+	mutex_init(&node->qrtr_tx_lock);
+
+	qrtr_node_assign(node, nid);
+
+	mutex_lock(&qrtr_node_lock);
+	list_add(&node->item, &qrtr_all_nodes);
+	mutex_unlock(&qrtr_node_lock);
+	ep->node = node;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(qrtr_endpoint_register);
+
+/**
+ * qrtr_endpoint_unregister - unregister endpoint
+ * @ep: endpoint to unregister
+ */
+void qrtr_endpoint_unregister(struct qrtr_endpoint *ep)
+{
+	struct qrtr_node *node = ep->node;
+	struct sockaddr_qrtr src = {AF_QIPCRTR, node->nid, QRTR_PORT_CTRL};
+	struct sockaddr_qrtr dst = {AF_QIPCRTR, qrtr_local_nid, QRTR_PORT_CTRL};
+	struct radix_tree_iter iter;
+	struct qrtr_ctrl_pkt *pkt;
+	struct qrtr_tx_flow *flow;
+	struct sk_buff *skb;
+	unsigned long flags;
+	void __rcu **slot;
+
+	mutex_lock(&node->ep_lock);
+	node->ep = NULL;
+	mutex_unlock(&node->ep_lock);
+
+	/* Notify the local controller about the event */
+	spin_lock_irqsave(&qrtr_nodes_lock, flags);
+	radix_tree_for_each_slot(slot, &qrtr_nodes, &iter, 0) {
+		if (*slot != node)
+			continue;
+		src.sq_node = iter.index;
+		skb = qrtr_alloc_ctrl_packet(&pkt, GFP_ATOMIC);
+		if (skb) {
+			pkt->cmd = cpu_to_le32(QRTR_TYPE_BYE);
+			qrtr_local_enqueue(NULL, skb, QRTR_TYPE_BYE, &src, &dst);
+		}
+	}
+	spin_unlock_irqrestore(&qrtr_nodes_lock, flags);
+
+	/* Wake up any transmitters waiting for resume-tx from the node */
+	mutex_lock(&node->qrtr_tx_lock);
+	radix_tree_for_each_slot(slot, &node->qrtr_tx_flow, &iter, 0) {
+		flow = *slot;
+		wake_up_interruptible_all(&flow->resume_tx);
+	}
+	mutex_unlock(&node->qrtr_tx_lock);
+
+	qrtr_node_release(node);
+	ep->node = NULL;
+}
+EXPORT_SYMBOL_GPL(qrtr_endpoint_unregister);
+
+/* Lookup socket by port.
+ *
+ * Callers must release with qrtr_port_put()
+ */
+static struct qrtr_sock *qrtr_port_lookup(int port)
+{
+	struct qrtr_sock *ipc;
+
+	if (port == QRTR_PORT_CTRL)
+		port = 0;
+
+	rcu_read_lock();
+	ipc = xa_load(&qrtr_ports, port);
+	if (ipc)
+		sock_hold(&ipc->sk);
+	rcu_read_unlock();
+
+	return ipc;
+}
+
+/* Release acquired socket. */
+static void qrtr_port_put(struct qrtr_sock *ipc)
+{
+	sock_put(&ipc->sk);
+}
+
+/* Remove port assignment. */
+static void qrtr_port_remove(struct qrtr_sock *ipc)
+{
+	struct qrtr_ctrl_pkt *pkt;
+	struct sk_buff *skb;
+	int port = ipc->us.sq_port;
+	struct sockaddr_qrtr to;
+
+	to.sq_family = AF_QIPCRTR;
+	to.sq_node = QRTR_NODE_BCAST;
+	to.sq_port = QRTR_PORT_CTRL;
+
+	skb = qrtr_alloc_ctrl_packet(&pkt, GFP_KERNEL);
+	if (skb) {
+		pkt->cmd = cpu_to_le32(QRTR_TYPE_DEL_CLIENT);
+		pkt->client.node = cpu_to_le32(ipc->us.sq_node);
+		pkt->client.port = cpu_to_le32(ipc->us.sq_port);
+
+		skb_set_owner_w(skb, &ipc->sk);
+		qrtr_bcast_enqueue(NULL, skb, QRTR_TYPE_DEL_CLIENT, &ipc->us,
+				   &to);
+	}
+
+	if (port == QRTR_PORT_CTRL)
+		port = 0;
+
+	__sock_put(&ipc->sk);
+
+	xa_erase(&qrtr_ports, port);
+
+	/* Ensure that if qrtr_port_lookup() did enter the RCU read section we
+	 * wait for it to up increment the refcount */
+	synchronize_rcu();
+}
+
+/* Assign port number to socket.
+ *
+ * Specify port in the integer pointed to by port, and it will be adjusted
+ * on return as necesssary.
+ *
+ * Port may be:
+ *   0: Assign ephemeral port in [QRTR_MIN_EPH_SOCKET, QRTR_MAX_EPH_SOCKET]
+ *   <QRTR_MIN_EPH_SOCKET: Specified; requires CAP_NET_ADMIN
+ *   >QRTR_MIN_EPH_SOCKET: Specified; available to all
+ */
+static int qrtr_port_assign(struct qrtr_sock *ipc, int *port)
+{
+	int rc;
+
+	if (!*port) {
+		rc = xa_alloc(&qrtr_ports, port, ipc, QRTR_EPH_PORT_RANGE,
+				GFP_KERNEL);
+	} else if (*port < QRTR_MIN_EPH_SOCKET && !capable(CAP_NET_ADMIN)) {
+		rc = -EACCES;
+	} else if (*port == QRTR_PORT_CTRL) {
+		rc = xa_insert(&qrtr_ports, 0, ipc, GFP_KERNEL);
+	} else {
+		rc = xa_insert(&qrtr_ports, *port, ipc, GFP_KERNEL);
+	}
+
+	if (rc == -EBUSY)
+		return -EADDRINUSE;
+	else if (rc < 0)
+		return rc;
+
+	sock_hold(&ipc->sk);
+
+	return 0;
+}
+
+/* Reset all non-control ports */
+static void qrtr_reset_ports(void)
+{
+	struct qrtr_sock *ipc;
+	unsigned long index;
+
+	rcu_read_lock();
+	xa_for_each_start(&qrtr_ports, index, ipc, 1) {
+		sock_hold(&ipc->sk);
+		ipc->sk.sk_err = ENETRESET;
+		sk_error_report(&ipc->sk);
+		sock_put(&ipc->sk);
+	}
+	rcu_read_unlock();
+}
+
+/* Bind socket to address.
+ *
+ * Socket should be locked upon call.
+ */
+static int __qrtr_bind(struct socket *sock,
+		       const struct sockaddr_qrtr *addr, int zapped)
+{
+	struct qrtr_sock *ipc = qrtr_sk(sock->sk);
+	struct sock *sk = sock->sk;
+	int port;
+	int rc;
+
+	/* rebinding ok */
+	if (!zapped && addr->sq_port == ipc->us.sq_port)
+		return 0;
+
+	port = addr->sq_port;
+	rc = qrtr_port_assign(ipc, &port);
+	if (rc)
+		return rc;
+
+	/* unbind previous, if any */
+	if (!zapped)
+		qrtr_port_remove(ipc);
+	ipc->us.sq_port = port;
+
+	sock_reset_flag(sk, SOCK_ZAPPED);
+
+	/* Notify all open ports about the new controller */
+	if (port == QRTR_PORT_CTRL)
+		qrtr_reset_ports();
+
+	return 0;
+}
+
+/* Auto bind to an ephemeral port. */
+static int qrtr_autobind(struct socket *sock)
+{
+	struct sock *sk = sock->sk;
+	struct sockaddr_qrtr addr;
+
+	if (!sock_flag(sk, SOCK_ZAPPED))
+		return 0;
+
+	addr.sq_family = AF_QIPCRTR;
+	addr.sq_node = qrtr_local_nid;
+	addr.sq_port = 0;
+
+	return __qrtr_bind(sock, &addr, 1);
+}
+
+/* Bind socket to specified sockaddr. */
+static int qrtr_bind(struct socket *sock, struct sockaddr *saddr, int len)
+{
+	DECLARE_SOCKADDR(struct sockaddr_qrtr *, addr, saddr);
+	struct qrtr_sock *ipc = qrtr_sk(sock->sk);
+	struct sock *sk = sock->sk;
+	int rc;
+
+	if (len < sizeof(*addr) || addr->sq_family != AF_QIPCRTR)
+		return -EINVAL;
+
+	if (addr->sq_node != ipc->us.sq_node)
+		return -EINVAL;
+
+	lock_sock(sk);
+	rc = __qrtr_bind(sock, addr, sock_flag(sk, SOCK_ZAPPED));
+	release_sock(sk);
+
+	return rc;
+}
+
+/* Queue packet to local peer socket. */
+static int qrtr_local_enqueue(struct qrtr_node *node, struct sk_buff *skb,
+			      int type, struct sockaddr_qrtr *from,
+			      struct sockaddr_qrtr *to)
+{
+	struct qrtr_sock *ipc;
+	struct qrtr_cb *cb;
+
+	ipc = qrtr_port_lookup(to->sq_port);
+	if (!ipc || &ipc->sk == skb->sk) { /* do not send to self */
+		if (ipc)
+			qrtr_port_put(ipc);
+		kfree_skb(skb);
+		return -ENODEV;
+	}
+
+	cb = (struct qrtr_cb *)skb->cb;
+	cb->src_node = from->sq_node;
+	cb->src_port = from->sq_port;
+
+	if (sock_queue_rcv_skb(&ipc->sk, skb)) {
+		qrtr_port_put(ipc);
+		kfree_skb(skb);
+		return -ENOSPC;
+	}
+
+	qrtr_port_put(ipc);
+
+	return 0;
+}
+
+/* Queue packet for broadcast. */
+static int qrtr_bcast_enqueue(struct qrtr_node *node, struct sk_buff *skb,
+			      int type, struct sockaddr_qrtr *from,
+			      struct sockaddr_qrtr *to)
+{
+	struct sk_buff *skbn;
+
+	mutex_lock(&qrtr_node_lock);
+	list_for_each_entry(node, &qrtr_all_nodes, item) {
+		skbn = pskb_copy(skb, GFP_KERNEL);
+		if (!skbn)
+			break;
+		skb_set_owner_w(skbn, skb->sk);
+		qrtr_node_enqueue(node, skbn, type, from, to);
+	}
+	mutex_unlock(&qrtr_node_lock);
+
+	qrtr_local_enqueue(NULL, skb, type, from, to);
+
+	return 0;
+}
+
+static int qrtr_sendmsg(struct socket *sock, struct msghdr *msg, size_t len)
+{
+	DECLARE_SOCKADDR(struct sockaddr_qrtr *, addr, msg->msg_name);
+	int (*enqueue_fn)(struct qrtr_node *, struct sk_buff *, int,
+			  struct sockaddr_qrtr *, struct sockaddr_qrtr *);
+	__le32 qrtr_type = cpu_to_le32(QRTR_TYPE_DATA);
+	struct qrtr_sock *ipc = qrtr_sk(sock->sk);
+	struct sock *sk = sock->sk;
+	struct qrtr_node *node;
+	struct sk_buff *skb;
+	size_t plen;
+	u32 type;
+	int rc;
+
+	if (msg->msg_flags & ~(MSG_DONTWAIT))
+		return -EINVAL;
+
+	if (len > 65535)
+		return -EMSGSIZE;
+
+	lock_sock(sk);
+
+	if (addr) {
+		if (msg->msg_namelen < sizeof(*addr)) {
+			release_sock(sk);
+			return -EINVAL;
+		}
+
+		if (addr->sq_family != AF_QIPCRTR) {
+			release_sock(sk);
+			return -EINVAL;
+		}
+
+		rc = qrtr_autobind(sock);
+		if (rc) {
+			release_sock(sk);
+			return rc;
+		}
+	} else if (sk->sk_state == TCP_ESTABLISHED) {
+		addr = &ipc->peer;
+	} else {
+		release_sock(sk);
+		return -ENOTCONN;
+	}
+
+	node = NULL;
+	if (addr->sq_node == QRTR_NODE_BCAST) {
+		if (addr->sq_port != QRTR_PORT_CTRL &&
+		    qrtr_local_nid != QRTR_NODE_BCAST) {
+			release_sock(sk);
+			return -ENOTCONN;
+		}
+		enqueue_fn = qrtr_bcast_enqueue;
+	} else if (addr->sq_node == ipc->us.sq_node) {
+		enqueue_fn = qrtr_local_enqueue;
+	} else {
+		node = qrtr_node_lookup(addr->sq_node);
+		if (!node) {
+			release_sock(sk);
+			return -ECONNRESET;
+		}
+		enqueue_fn = qrtr_node_enqueue;
+	}
+
+	plen = (len + 3) & ~3;
+	skb = sock_alloc_send_skb(sk, plen + QRTR_HDR_MAX_SIZE,
+				  msg->msg_flags & MSG_DONTWAIT, &rc);
+	if (!skb) {
+		rc = -ENOMEM;
+		goto out_node;
+	}
+
+	skb_reserve(skb, QRTR_HDR_MAX_SIZE);
+
+	rc = memcpy_from_msg(skb_put(skb, len), msg, len);
+	if (rc) {
+		kfree_skb(skb);
+		goto out_node;
+	}
+
+	if (ipc->us.sq_port == QRTR_PORT_CTRL) {
+		if (len < 4) {
+			rc = -EINVAL;
+			kfree_skb(skb);
+			goto out_node;
+		}
+
+		/* control messages already require the type as 'command' */
+		skb_copy_bits(skb, 0, &qrtr_type, 4);
+	}
+
+	type = le32_to_cpu(qrtr_type);
+	rc = enqueue_fn(node, skb, type, &ipc->us, addr);
+	if (rc >= 0)
+		rc = len;
+
+out_node:
+	qrtr_node_release(node);
+	release_sock(sk);
+
+	return rc;
+}
+
+static int qrtr_send_resume_tx(struct qrtr_cb *cb)
+{
+	struct sockaddr_qrtr remote = { AF_QIPCRTR, cb->src_node, cb->src_port };
+	struct sockaddr_qrtr local = { AF_QIPCRTR, cb->dst_node, cb->dst_port };
+	struct qrtr_ctrl_pkt *pkt;
+	struct qrtr_node *node;
+	struct sk_buff *skb;
+	int ret;
+
+	node = qrtr_node_lookup(remote.sq_node);
+	if (!node)
+		return -EINVAL;
+
+	skb = qrtr_alloc_ctrl_packet(&pkt, GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
+
+	pkt->cmd = cpu_to_le32(QRTR_TYPE_RESUME_TX);
+	pkt->client.node = cpu_to_le32(cb->dst_node);
+	pkt->client.port = cpu_to_le32(cb->dst_port);
+
+	ret = qrtr_node_enqueue(node, skb, QRTR_TYPE_RESUME_TX, &local, &remote);
+
+	qrtr_node_release(node);
+
+	return ret;
+}
+
+static int qrtr_recvmsg(struct socket *sock, struct msghdr *msg,
+			size_t size, int flags)
+{
+	DECLARE_SOCKADDR(struct sockaddr_qrtr *, addr, msg->msg_name);
+	struct sock *sk = sock->sk;
+	struct sk_buff *skb;
+	struct qrtr_cb *cb;
+	int copied, rc;
+
+	lock_sock(sk);
+
+	if (sock_flag(sk, SOCK_ZAPPED)) {
+		release_sock(sk);
+		return -EADDRNOTAVAIL;
+	}
+
+	skb = skb_recv_datagram(sk, flags & ~MSG_DONTWAIT,
+				flags & MSG_DONTWAIT, &rc);
+	if (!skb) {
+		release_sock(sk);
+		return rc;
+	}
+	cb = (struct qrtr_cb *)skb->cb;
+
+	copied = skb->len;
+	if (copied > size) {
+		copied = size;
+		msg->msg_flags |= MSG_TRUNC;
+	}
+
+	rc = skb_copy_datagram_msg(skb, 0, msg, copied);
+	if (rc < 0)
+		goto out;
+	rc = copied;
+
+	if (addr) {
+		/* There is an anonymous 2-byte hole after sq_family,
+		 * make sure to clear it.
+		 */
+		memset(addr, 0, sizeof(*addr));
+
+		addr->sq_family = AF_QIPCRTR;
+		addr->sq_node = cb->src_node;
+		addr->sq_port = cb->src_port;
+		msg->msg_namelen = sizeof(*addr);
+	}
+
+out:
+	if (cb->confirm_rx)
+		qrtr_send_resume_tx(cb);
+
+	skb_free_datagram(sk, skb);
+	release_sock(sk);
+
+	return rc;
+}
+
+static int qrtr_connect(struct socket *sock, struct sockaddr *saddr,
+			int len, int flags)
+{
+	DECLARE_SOCKADDR(struct sockaddr_qrtr *, addr, saddr);
+	struct qrtr_sock *ipc = qrtr_sk(sock->sk);
+	struct sock *sk = sock->sk;
+	int rc;
+
+	if (len < sizeof(*addr) || addr->sq_family != AF_QIPCRTR)
+		return -EINVAL;
+
+	lock_sock(sk);
+
+	sk->sk_state = TCP_CLOSE;
+	sock->state = SS_UNCONNECTED;
+
+	rc = qrtr_autobind(sock);
+	if (rc) {
+		release_sock(sk);
+		return rc;
+	}
+
+	ipc->peer = *addr;
+	sock->state = SS_CONNECTED;
+	sk->sk_state = TCP_ESTABLISHED;
+
+	release_sock(sk);
+
+	return 0;
+}
+
+static int qrtr_getname(struct socket *sock, struct sockaddr *saddr,
+			int peer)
+{
+	struct qrtr_sock *ipc = qrtr_sk(sock->sk);
+	struct sockaddr_qrtr qaddr;
+	struct sock *sk = sock->sk;
+
+	lock_sock(sk);
+	if (peer) {
+		if (sk->sk_state != TCP_ESTABLISHED) {
+			release_sock(sk);
+			return -ENOTCONN;
+		}
+
+		qaddr = ipc->peer;
+	} else {
+		qaddr = ipc->us;
+	}
+	release_sock(sk);
+
+	qaddr.sq_family = AF_QIPCRTR;
+
+	memcpy(saddr, &qaddr, sizeof(qaddr));
+
+	return sizeof(qaddr);
+}
+
+static int qrtr_ioctl(struct socket *sock, unsigned int cmd, unsigned long arg)
+{
+	void __user *argp = (void __user *)arg;
+	struct qrtr_sock *ipc = qrtr_sk(sock->sk);
+	struct sock *sk = sock->sk;
+	struct sockaddr_qrtr *sq;
+	struct sk_buff *skb;
+	struct ifreq ifr;
+	long len = 0;
+	int rc = 0;
+
+	lock_sock(sk);
+
+	switch (cmd) {
+	case TIOCOUTQ:
+		len = sk->sk_sndbuf - sk_wmem_alloc_get(sk);
+		if (len < 0)
+			len = 0;
+		rc = put_user(len, (int __user *)argp);
+		break;
+	case TIOCINQ:
+		skb = skb_peek(&sk->sk_receive_queue);
+		if (skb)
+			len = skb->len;
+		rc = put_user(len, (int __user *)argp);
+		break;
+	case SIOCGIFADDR:
+		if (get_user_ifreq(&ifr, NULL, argp)) {
+			rc = -EFAULT;
+			break;
+		}
+
+		sq = (struct sockaddr_qrtr *)&ifr.ifr_addr;
+		*sq = ipc->us;
+		if (put_user_ifreq(&ifr, argp)) {
+			rc = -EFAULT;
+			break;
+		}
+		break;
+	case SIOCADDRT:
+	case SIOCDELRT:
+	case SIOCSIFADDR:
+	case SIOCGIFDSTADDR:
+	case SIOCSIFDSTADDR:
+	case SIOCGIFBRDADDR:
+	case SIOCSIFBRDADDR:
+	case SIOCGIFNETMASK:
+	case SIOCSIFNETMASK:
+		rc = -EINVAL;
+		break;
+	default:
+		rc = -ENOIOCTLCMD;
+		break;
+	}
+
+	release_sock(sk);
+
+	return rc;
+}
+
+static int qrtr_release(struct socket *sock)
+{
+	struct sock *sk = sock->sk;
+	struct qrtr_sock *ipc;
+
+	if (!sk)
+		return 0;
+
+	lock_sock(sk);
+
+	ipc = qrtr_sk(sk);
+	sk->sk_shutdown = SHUTDOWN_MASK;
+	if (!sock_flag(sk, SOCK_DEAD))
+		sk->sk_state_change(sk);
+
+	sock_set_flag(sk, SOCK_DEAD);
+	sock_orphan(sk);
+	sock->sk = NULL;
+
+	if (!sock_flag(sk, SOCK_ZAPPED))
+		qrtr_port_remove(ipc);
+
+	skb_queue_purge(&sk->sk_receive_queue);
+
+	release_sock(sk);
+	sock_put(sk);
+
+	return 0;
+}
+
+static const struct proto_ops qrtr_proto_ops = {
+	.owner		= THIS_MODULE,
+	.family		= AF_QIPCRTR,
+	.bind		= qrtr_bind,
+	.connect	= qrtr_connect,
+	.socketpair	= sock_no_socketpair,
+	.accept		= sock_no_accept,
+	.listen		= sock_no_listen,
+	.sendmsg	= qrtr_sendmsg,
+	.recvmsg	= qrtr_recvmsg,
+	.getname	= qrtr_getname,
+	.ioctl		= qrtr_ioctl,
+	.gettstamp	= sock_gettstamp,
+	.poll		= datagram_poll,
+	.shutdown	= sock_no_shutdown,
+	.release	= qrtr_release,
+	.mmap		= sock_no_mmap,
+	.sendpage	= sock_no_sendpage,
+};
+
+static struct proto qrtr_proto = {
+	.name		= "QIPCRTR",
+	.owner		= THIS_MODULE,
+	.obj_size	= sizeof(struct qrtr_sock),
+};
+
+static int qrtr_create(struct net *net, struct socket *sock,
+		       int protocol, int kern)
+{
+	struct qrtr_sock *ipc;
+	struct sock *sk;
+
+	if (sock->type != SOCK_DGRAM)
+		return -EPROTOTYPE;
+
+	sk = sk_alloc(net, AF_QIPCRTR, GFP_KERNEL, &qrtr_proto, kern);
+	if (!sk)
+		return -ENOMEM;
+
+	sock_set_flag(sk, SOCK_ZAPPED);
+
+	sock_init_data(sock, sk);
+	sock->ops = &qrtr_proto_ops;
+
+	ipc = qrtr_sk(sk);
+	ipc->us.sq_family = AF_QIPCRTR;
+	ipc->us.sq_node = qrtr_local_nid;
+	ipc->us.sq_port = 0;
+
+	return 0;
+}
+
+static const struct net_proto_family qrtr_family = {
+	.owner	= THIS_MODULE,
+	.family	= AF_QIPCRTR,
+	.create	= qrtr_create,
+};
+
+static int __init qrtr_proto_init(void)
+{
+	int rc;
+
+	rc = proto_register(&qrtr_proto, 1);
+	if (rc)
+		return rc;
+
+	rc = sock_register(&qrtr_family);
+	if (rc)
+		goto err_proto;
+
+	rc = qrtr_ns_init();
+	if (rc)
+		goto err_sock;
+
+	return 0;
+
+err_sock:
+	sock_unregister(qrtr_family.family);
+err_proto:
+	proto_unregister(&qrtr_proto);
+	return rc;
+}
+postcore_initcall(qrtr_proto_init);
+
+static void __exit qrtr_proto_fini(void)
+{
+	qrtr_ns_remove();
+	sock_unregister(qrtr_family.family);
+	proto_unregister(&qrtr_proto);
+}
+module_exit(qrtr_proto_fini);
+
+MODULE_DESCRIPTION("Qualcomm IPC-router driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS_NETPROTO(PF_QIPCRTR);
--- linux-xilinx-zynqmp-5.15.0.orig/net/qrtr/mhi.c
+++ linux-xilinx-zynqmp-5.15.0/net/qrtr/mhi.c
@@ -78,11 +78,6 @@
 	struct qrtr_mhi_dev *qdev;
 	int rc;
 
-	/* start channels */
-	rc = mhi_prepare_for_transfer(mhi_dev);
-	if (rc)
-		return rc;
-
 	qdev = devm_kzalloc(&mhi_dev->dev, sizeof(*qdev), GFP_KERNEL);
 	if (!qdev)
 		return -ENOMEM;
@@ -96,6 +91,13 @@
 	if (rc)
 		return rc;
 
+	/* start channels */
+	rc = mhi_prepare_for_transfer(mhi_dev);
+	if (rc) {
+		qrtr_endpoint_unregister(&qdev->ep);
+		return rc;
+	}
+
 	dev_dbg(qdev->dev, "Qualcomm MHI QRTR driver probed\n");
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/qrtr/ns.c
+++ linux-xilinx-zynqmp-5.15.0/net/qrtr/ns.c
@@ -83,7 +83,10 @@
 
 	node->id = node_id;
 
-	radix_tree_insert(&nodes, node_id, node);
+	if (radix_tree_insert(&nodes, node_id, node)) {
+		kfree(node);
+		return NULL;
+	}
 
 	return node;
 }
@@ -270,7 +273,7 @@
 	return NULL;
 }
 
-static int server_del(struct qrtr_node *node, unsigned int port)
+static int server_del(struct qrtr_node *node, unsigned int port, bool bcast)
 {
 	struct qrtr_lookup *lookup;
 	struct qrtr_server *srv;
@@ -283,7 +286,7 @@
 	radix_tree_delete(&node->servers, port);
 
 	/* Broadcast the removal of local servers */
-	if (srv->node == qrtr_ns.local_node)
+	if (srv->node == qrtr_ns.local_node && bcast)
 		service_announce_del(&qrtr_ns.bcast_sq, srv);
 
 	/* Announce the service's disappearance to observers */
@@ -369,7 +372,7 @@
 		}
 		slot = radix_tree_iter_resume(slot, &iter);
 		rcu_read_unlock();
-		server_del(node, srv->port);
+		server_del(node, srv->port, true);
 		rcu_read_lock();
 	}
 	rcu_read_unlock();
@@ -455,10 +458,13 @@
 		kfree(lookup);
 	}
 
-	/* Remove the server belonging to this port */
+	/* Remove the server belonging to this port but don't broadcast
+	 * DEL_SERVER. Neighbours would've already removed the server belonging
+	 * to this port due to the DEL_CLIENT broadcast from qrtr_port_remove().
+	 */
 	node = node_get(node_id);
 	if (node)
-		server_del(node, port);
+		server_del(node, port, false);
 
 	/* Advertise the removal of this client to all local servers */
 	local_node = node_get(qrtr_ns.local_node);
@@ -563,7 +569,9 @@
 	if (!node)
 		return -ENOENT;
 
-	return server_del(node, port);
+	server_del(node, port, true);
+
+	return 0;
 }
 
 static int ctrl_cmd_new_lookup(struct sockaddr_qrtr *from,
@@ -799,6 +807,24 @@
 	if (ret < 0)
 		goto err_wq;
 
+	/* As the qrtr ns socket owner and creator is the same module, we have
+	 * to decrease the qrtr module reference count to guarantee that it
+	 * remains zero after the ns socket is created, otherwise, executing
+	 * "rmmod" command is unable to make the qrtr module deleted after the
+	 *  qrtr module is inserted successfully.
+	 *
+	 * However, the reference count is increased twice in
+	 * sock_create_kern(): one is to increase the reference count of owner
+	 * of qrtr socket's proto_ops struct; another is to increment the
+	 * reference count of owner of qrtr proto struct. Therefore, we must
+	 * decrement the module reference count twice to ensure that it keeps
+	 * zero after server's listening socket is created. Of course, we
+	 * must bump the module reference count twice as well before the socket
+	 * is closed.
+	 */
+	module_put(qrtr_ns.sock->ops->owner);
+	module_put(qrtr_ns.sock->sk->sk_prot_creator->owner);
+
 	return 0;
 
 err_wq:
@@ -813,6 +839,15 @@
 {
 	cancel_work_sync(&qrtr_ns.work);
 	destroy_workqueue(qrtr_ns.workqueue);
+
+	/* sock_release() expects the two references that were put during
+	 * qrtr_ns_init(). This function is only called during module remove,
+	 * so try_stop_module() has already set the refcnt to 0. Use
+	 * __module_get() instead of try_module_get() to successfully take two
+	 * references.
+	 */
+	__module_get(qrtr_ns.sock->ops->owner);
+	__module_get(qrtr_ns.sock->sk->sk_prot_creator->owner);
 	sock_release(qrtr_ns.sock);
 }
 EXPORT_SYMBOL_GPL(qrtr_ns_remove);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/af_rds.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/af_rds.c
@@ -419,7 +419,7 @@
 
 	rs->rs_rx_traces = trace.rx_traces;
 	for (i = 0; i < rs->rs_rx_traces; i++) {
-		if (trace.rx_trace_pos[i] > RDS_MSG_RX_DGRAM_TRACE_MAX) {
+		if (trace.rx_trace_pos[i] >= RDS_MSG_RX_DGRAM_TRACE_MAX) {
 			rs->rs_rx_traces = 0;
 			return -EFAULT;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/connection.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/connection.c
@@ -253,6 +253,7 @@
 				 * should end up here, but if it
 				 * does, reset/destroy the connection.
 				 */
+				kfree(conn->c_path);
 				kmem_cache_free(rds_conn_slab, conn);
 				conn = ERR_PTR(-EOPNOTSUPP);
 				goto out;
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/ib_recv.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/ib_recv.c
@@ -363,6 +363,7 @@
 static void release_refill(struct rds_connection *conn)
 {
 	clear_bit(RDS_RECV_REFILL, &conn->c_flags);
+	smp_mb__after_atomic();
 
 	/* We don't use wait_on_bit()/wake_up_bit() because our waking is in a
 	 * hot path and finding waiters is very rare.  We don't want to walk
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/ib_send.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/ib_send.c
@@ -503,7 +503,7 @@
 	int flow_controlled = 0;
 	int nr_sig = 0;
 
-	BUG_ON(off % RDS_FRAG_SIZE);
+	BUG_ON(!conn->c_loopback && off % RDS_FRAG_SIZE);
 	BUG_ON(hdr_off != 0 && hdr_off != sizeof(struct rds_header));
 
 	/* Do not send cong updates to IB loopback */
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/message.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/message.c
@@ -104,9 +104,9 @@
 	spin_lock_irqsave(&q->lock, flags);
 	head = &q->zcookie_head;
 	if (!list_empty(head)) {
-		info = list_entry(head, struct rds_msg_zcopy_info,
-				  rs_zcookie_next);
-		if (info && rds_zcookie_add(info, cookie)) {
+		info = list_first_entry(head, struct rds_msg_zcopy_info,
+					rs_zcookie_next);
+		if (rds_zcookie_add(info, cookie)) {
 			spin_unlock_irqrestore(&q->lock, flags);
 			kfree(rds_info_from_znotifier(znotif));
 			/* caller invokes rds_wake_sk_sleep() */
@@ -118,7 +118,7 @@
 	ck = &info->zcookies;
 	memset(ck, 0, sizeof(*ck));
 	WARN_ON(!rds_zcookie_add(info, cookie));
-	list_add_tail(&q->zcookie_head, &info->rs_zcookie_next);
+	list_add_tail(&info->rs_zcookie_next, &q->zcookie_head);
 
 	spin_unlock_irqrestore(&q->lock, flags);
 	/* caller invokes rds_wake_sk_sleep() */
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/rdma.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/rdma.c
@@ -301,6 +301,9 @@
 			kfree(sg);
 		}
 		ret = PTR_ERR(trans_private);
+		/* Trigger connection so that its ready for the next retry */
+		if (ret == -ENODEV && cp)
+			rds_conn_connect_if_down(cp->cp_conn);
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/rdma_transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/rdma_transport.c
@@ -86,11 +86,13 @@
 		break;
 
 	case RDMA_CM_EVENT_ADDR_RESOLVED:
-		rdma_set_service_type(cm_id, conn->c_tos);
-		rdma_set_min_rnr_timer(cm_id, IB_RNR_TIMER_000_32);
-		/* XXX do we need to clean up if this fails? */
-		ret = rdma_resolve_route(cm_id,
-					 RDS_RDMA_RESOLVE_TIMEOUT_MS);
+		if (conn) {
+			rdma_set_service_type(cm_id, conn->c_tos);
+			rdma_set_min_rnr_timer(cm_id, IB_RNR_TIMER_000_32);
+			/* XXX do we need to clean up if this fails? */
+			ret = rdma_resolve_route(cm_id,
+						 RDS_RDMA_RESOLVE_TIMEOUT_MS);
+		}
 		break;
 
 	case RDMA_CM_EVENT_ROUTE_RESOLVED:
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/recv.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/recv.c
@@ -424,6 +424,7 @@
 	struct sock *sk = rds_rs_to_sk(rs);
 	int ret = 0;
 	unsigned long flags;
+	struct rds_incoming *to_drop = NULL;
 
 	write_lock_irqsave(&rs->rs_recv_lock, flags);
 	if (!list_empty(&inc->i_item)) {
@@ -434,11 +435,14 @@
 					      -be32_to_cpu(inc->i_hdr.h_len),
 					      inc->i_hdr.h_dport);
 			list_del_init(&inc->i_item);
-			rds_inc_put(inc);
+			to_drop = inc;
 		}
 	}
 	write_unlock_irqrestore(&rs->rs_recv_lock, flags);
 
+	if (to_drop)
+		rds_inc_put(to_drop);
+
 	rdsdebug("inc %p rs %p still %d dropped %d\n", inc, rs, ret, drop);
 	return ret;
 }
@@ -757,16 +761,21 @@
 	struct sock *sk = rds_rs_to_sk(rs);
 	struct rds_incoming *inc, *tmp;
 	unsigned long flags;
+	LIST_HEAD(to_drop);
 
 	write_lock_irqsave(&rs->rs_recv_lock, flags);
 	list_for_each_entry_safe(inc, tmp, &rs->rs_recv_queue, i_item) {
 		rds_recv_rcvbuf_delta(rs, sk, inc->i_conn->c_lcong,
 				      -be32_to_cpu(inc->i_hdr.h_len),
 				      inc->i_hdr.h_dport);
+		list_move(&inc->i_item, &to_drop);
+	}
+	write_unlock_irqrestore(&rs->rs_recv_lock, flags);
+
+	list_for_each_entry_safe(inc, tmp, &to_drop, i_item) {
 		list_del_init(&inc->i_item);
 		rds_inc_put(inc);
 	}
-	write_unlock_irqrestore(&rs->rs_recv_lock, flags);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/send.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/send.c
@@ -103,13 +103,12 @@
 
 static int acquire_in_xmit(struct rds_conn_path *cp)
 {
-	return test_and_set_bit(RDS_IN_XMIT, &cp->cp_flags) == 0;
+	return test_and_set_bit_lock(RDS_IN_XMIT, &cp->cp_flags) == 0;
 }
 
 static void release_in_xmit(struct rds_conn_path *cp)
 {
-	clear_bit(RDS_IN_XMIT, &cp->cp_flags);
-	smp_mb__after_atomic();
+	clear_bit_unlock(RDS_IN_XMIT, &cp->cp_flags);
 	/*
 	 * We don't use wait_on_bit()/wake_up_bit() because our waking is in a
 	 * hot path and finding waiters is very rare.  We don't want to walk
@@ -1314,12 +1313,8 @@
 
 	/* Parse any control messages the user may have included. */
 	ret = rds_cmsg_send(rs, rm, msg, &allocated_mr, &vct);
-	if (ret) {
-		/* Trigger connection so that its ready for the next retry */
-		if (ret ==  -EAGAIN)
-			rds_conn_connect_if_down(conn);
+	if (ret)
 		goto out;
-	}
 
 	if (rm->rdma.op_active && !conn->c_trans->xmit_rdma) {
 		printk_ratelimited(KERN_NOTICE "rdma_op %p conn xmit_rdma %p\n",
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/tcp.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/tcp.c
@@ -166,10 +166,10 @@
 	 */
 	atomic_set(&cp->cp_state, RDS_CONN_RESETTING);
 	wait_event(cp->cp_waitq, !test_bit(RDS_IN_XMIT, &cp->cp_flags));
-	lock_sock(osock->sk);
 	/* reset receive side state for rds_tcp_data_recv() for osock  */
 	cancel_delayed_work_sync(&cp->cp_send_w);
 	cancel_delayed_work_sync(&cp->cp_recv_w);
+	lock_sock(osock->sk);
 	if (tc->t_tinc) {
 		rds_inc_put(&tc->t_tinc->ti_inc);
 		tc->t_tinc = NULL;
@@ -500,7 +500,7 @@
 		sk->sk_userlocks |= SOCK_SNDBUF_LOCK;
 	}
 	if (rtn->rcvbuf_size > 0) {
-		sk->sk_sndbuf = rtn->rcvbuf_size;
+		sk->sk_rcvbuf = rtn->rcvbuf_size;
 		sk->sk_userlocks |= SOCK_RCVBUF_LOCK;
 	}
 	release_sock(sk);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/tcp_connect.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/tcp_connect.c
@@ -142,7 +142,7 @@
 		addrlen = sizeof(sin);
 	}
 
-	ret = sock->ops->bind(sock, addr, addrlen);
+	ret = kernel_bind(sock, addr, addrlen);
 	if (ret) {
 		rdsdebug("bind failed with %d at address %pI6c\n",
 			 ret, &conn->c_laddr);
@@ -170,7 +170,7 @@
 	 * own the socket
 	 */
 	rds_tcp_set_callbacks(sock, cp);
-	ret = sock->ops->connect(sock, addr, addrlen, O_NONBLOCK);
+	ret = kernel_connect(sock, addr, addrlen, O_NONBLOCK);
 
 	rdsdebug("connect to address %pI6c returned %d\n", &conn->c_faddr, ret);
 	if (ret == -EINPROGRESS)
--- linux-xilinx-zynqmp-5.15.0.orig/net/rds/tcp_listen.c
+++ linux-xilinx-zynqmp-5.15.0/net/rds/tcp_listen.c
@@ -301,7 +301,7 @@
 		addr_len = sizeof(*sin);
 	}
 
-	ret = sock->ops->bind(sock, (struct sockaddr *)&ss, addr_len);
+	ret = kernel_bind(sock, (struct sockaddr *)&ss, addr_len);
 	if (ret < 0) {
 		rdsdebug("could not bind %s listener socket: %d\n",
 			 isv6 ? "IPv6" : "IPv4", ret);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rfkill/rfkill-gpio.c
+++ linux-xilinx-zynqmp-5.15.0/net/rfkill/rfkill-gpio.c
@@ -30,8 +30,12 @@
 {
 	struct rfkill_gpio_data *rfkill = data;
 
-	if (!blocked && !IS_ERR(rfkill->clk) && !rfkill->clk_enabled)
-		clk_enable(rfkill->clk);
+	if (!blocked && !IS_ERR(rfkill->clk) && !rfkill->clk_enabled) {
+		int ret = clk_enable(rfkill->clk);
+
+		if (ret)
+			return ret;
+	}
 
 	gpiod_set_value_cansleep(rfkill->shutdown_gpio, !blocked);
 	gpiod_set_value_cansleep(rfkill->reset_gpio, !blocked);
@@ -98,13 +102,13 @@
 
 	rfkill->clk = devm_clk_get(&pdev->dev, NULL);
 
-	gpio = devm_gpiod_get_optional(&pdev->dev, "reset", GPIOD_OUT_LOW);
+	gpio = devm_gpiod_get_optional(&pdev->dev, "reset", GPIOD_ASIS);
 	if (IS_ERR(gpio))
 		return PTR_ERR(gpio);
 
 	rfkill->reset_gpio = gpio;
 
-	gpio = devm_gpiod_get_optional(&pdev->dev, "shutdown", GPIOD_OUT_LOW);
+	gpio = devm_gpiod_get_optional(&pdev->dev, "shutdown", GPIOD_ASIS);
 	if (IS_ERR(gpio))
 		return PTR_ERR(gpio);
 
@@ -116,6 +120,14 @@
 		return -EINVAL;
 	}
 
+	ret = gpiod_direction_output(rfkill->reset_gpio, true);
+	if (ret)
+		return ret;
+
+	ret = gpiod_direction_output(rfkill->shutdown_gpio, true);
+	if (ret)
+		return ret;
+
 	rfkill->rfkill_dev = rfkill_alloc(rfkill->name, &pdev->dev,
 					  rfkill->type, &rfkill_gpio_ops,
 					  rfkill);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rose/af_rose.c
+++ linux-xilinx-zynqmp-5.15.0/net/rose/af_rose.c
@@ -181,20 +181,47 @@
  */
 static void rose_kill_by_device(struct net_device *dev)
 {
-	struct sock *s;
+	struct sock *sk, *array[16];
+	struct rose_sock *rose;
+	bool rescan;
+	int i, cnt;
 
+start:
+	rescan = false;
+	cnt = 0;
 	spin_lock_bh(&rose_list_lock);
-	sk_for_each(s, &rose_list) {
-		struct rose_sock *rose = rose_sk(s);
+	sk_for_each(sk, &rose_list) {
+		rose = rose_sk(sk);
+		if (rose->device == dev) {
+			if (cnt == ARRAY_SIZE(array)) {
+				rescan = true;
+				break;
+			}
+			sock_hold(sk);
+			array[cnt++] = sk;
+		}
+	}
+	spin_unlock_bh(&rose_list_lock);
 
+	for (i = 0; i < cnt; i++) {
+		sk = array[cnt];
+		rose = rose_sk(sk);
+		lock_sock(sk);
+		spin_lock_bh(&rose_list_lock);
 		if (rose->device == dev) {
-			rose_disconnect(s, ENETUNREACH, ROSE_OUT_OF_ORDER, 0);
+			rose_disconnect(sk, ENETUNREACH, ROSE_OUT_OF_ORDER, 0);
 			if (rose->neighbour)
 				rose->neighbour->use--;
+			dev_put(rose->device);
 			rose->device = NULL;
 		}
+		spin_unlock_bh(&rose_list_lock);
+		release_sock(sk);
+		sock_put(sk);
+		cond_resched();
 	}
-	spin_unlock_bh(&rose_list_lock);
+	if (rescan)
+		goto start;
 }
 
 /*
@@ -369,15 +396,15 @@
 {
 	struct sock *sk = sock->sk;
 	struct rose_sock *rose = rose_sk(sk);
-	int opt;
+	unsigned int opt;
 
 	if (level != SOL_ROSE)
 		return -ENOPROTOOPT;
 
-	if (optlen < sizeof(int))
+	if (optlen < sizeof(unsigned int))
 		return -EINVAL;
 
-	if (copy_from_sockptr(&opt, optval, sizeof(int)))
+	if (copy_from_sockptr(&opt, optval, sizeof(unsigned int)))
 		return -EFAULT;
 
 	switch (optname) {
@@ -386,31 +413,31 @@
 		return 0;
 
 	case ROSE_T1:
-		if (opt < 1)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		rose->t1 = opt * HZ;
 		return 0;
 
 	case ROSE_T2:
-		if (opt < 1)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		rose->t2 = opt * HZ;
 		return 0;
 
 	case ROSE_T3:
-		if (opt < 1)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		rose->t3 = opt * HZ;
 		return 0;
 
 	case ROSE_HOLDBACK:
-		if (opt < 1)
+		if (opt < 1 || opt > UINT_MAX / HZ)
 			return -EINVAL;
 		rose->hb = opt * HZ;
 		return 0;
 
 	case ROSE_IDLE:
-		if (opt < 0)
+		if (opt > UINT_MAX / (60 * HZ))
 			return -EINVAL;
 		rose->idle = opt * 60 * HZ;
 		return 0;
@@ -486,6 +513,12 @@
 {
 	struct sock *sk = sock->sk;
 
+	lock_sock(sk);
+	if (sock->state != SS_UNCONNECTED) {
+		release_sock(sk);
+		return -EINVAL;
+	}
+
 	if (sk->sk_state != TCP_LISTEN) {
 		struct rose_sock *rose = rose_sk(sk);
 
@@ -495,8 +528,10 @@
 		memset(rose->dest_digis, 0, AX25_ADDR_LEN * ROSE_MAX_DIGIS);
 		sk->sk_max_ack_backlog = backlog;
 		sk->sk_state           = TCP_LISTEN;
+		release_sock(sk);
 		return 0;
 	}
+	release_sock(sk);
 
 	return -EOPNOTSUPP;
 }
@@ -591,6 +626,8 @@
 	rose->idle	= orose->idle;
 	rose->defer	= orose->defer;
 	rose->device	= orose->device;
+	if (rose->device)
+		dev_hold(rose->device);
 	rose->qbitincl	= orose->qbitincl;
 
 	return sk;
@@ -644,6 +681,10 @@
 		break;
 	}
 
+	spin_lock_bh(&rose_list_lock);
+	dev_put(rose->device);
+	rose->device = NULL;
+	spin_unlock_bh(&rose_list_lock);
 	sock->sk = NULL;
 	release_sock(sk);
 	sock_put(sk);
@@ -659,11 +700,9 @@
 	struct net_device *dev;
 	ax25_address *source;
 	ax25_uid_assoc *user;
+	int err = -EINVAL;
 	int n;
 
-	if (!sock_flag(sk, SOCK_ZAPPED))
-		return -EINVAL;
-
 	if (addr_len != sizeof(struct sockaddr_rose) && addr_len != sizeof(struct full_sockaddr_rose))
 		return -EINVAL;
 
@@ -676,8 +715,15 @@
 	if ((unsigned int) addr->srose_ndigis > ROSE_MAX_DIGIS)
 		return -EINVAL;
 
-	if ((dev = rose_dev_get(&addr->srose_addr)) == NULL)
-		return -EADDRNOTAVAIL;
+	lock_sock(sk);
+
+	if (!sock_flag(sk, SOCK_ZAPPED))
+		goto out_release;
+
+	err = -EADDRNOTAVAIL;
+	dev = rose_dev_get(&addr->srose_addr);
+	if (!dev)
+		goto out_release;
 
 	source = &addr->srose_call;
 
@@ -688,7 +734,8 @@
 	} else {
 		if (ax25_uid_policy && !capable(CAP_NET_BIND_SERVICE)) {
 			dev_put(dev);
-			return -EACCES;
+			err = -EACCES;
+			goto out_release;
 		}
 		rose->source_call   = *source;
 	}
@@ -710,8 +757,10 @@
 	rose_insert_socket(sk);
 
 	sock_reset_flag(sk, SOCK_ZAPPED);
-
-	return 0;
+	err = 0;
+out_release:
+	release_sock(sk);
+	return err;
 }
 
 static int rose_connect(struct socket *sock, struct sockaddr *uaddr, int addr_len, int flags)
@@ -720,7 +769,6 @@
 	struct rose_sock *rose = rose_sk(sk);
 	struct sockaddr_rose *addr = (struct sockaddr_rose *)uaddr;
 	unsigned char cause, diagnostic;
-	struct net_device *dev;
 	ax25_uid_assoc *user;
 	int n, err = 0;
 
@@ -777,9 +825,12 @@
 	}
 
 	if (sock_flag(sk, SOCK_ZAPPED)) {	/* Must bind first - autobinding in this may or may not work */
+		struct net_device *dev;
+
 		sock_reset_flag(sk, SOCK_ZAPPED);
 
-		if ((dev = rose_dev_first()) == NULL) {
+		dev = rose_dev_first();
+		if (!dev) {
 			err = -ENETUNREACH;
 			goto out_release;
 		}
@@ -787,6 +838,7 @@
 		user = ax25_findbyuid(current_euid());
 		if (!user) {
 			err = -EINVAL;
+			dev_put(dev);
 			goto out_release;
 		}
 
@@ -1292,9 +1344,11 @@
 	case TIOCINQ: {
 		struct sk_buff *skb;
 		long amount = 0L;
-		/* These two are safe on a single CPU system as only user tasks fiddle here */
+
+		spin_lock_irq(&sk->sk_receive_queue.lock);
 		if ((skb = skb_peek(&sk->sk_receive_queue)) != NULL)
 			amount = skb->len;
+		spin_unlock_irq(&sk->sk_receive_queue.lock);
 		return put_user(amount, (unsigned int __user *) argp);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/rose/rose_link.c
+++ linux-xilinx-zynqmp-5.15.0/net/rose/rose_link.c
@@ -236,6 +236,9 @@
 	unsigned char *dptr;
 	int len;
 
+	if (!neigh->dev)
+		return;
+
 	len = AX25_BPQ_HEADER_LEN + AX25_MAX_HEADER_LEN + ROSE_MIN_LEN + 3;
 
 	if ((skb = alloc_skb(len, GFP_ATOMIC)) == NULL)
--- linux-xilinx-zynqmp-5.15.0.orig/net/rose/rose_loopback.c
+++ linux-xilinx-zynqmp-5.15.0/net/rose/rose_loopback.c
@@ -96,7 +96,8 @@
 		}
 
 		if (frametype == ROSE_CALL_REQUEST) {
-			if (!rose_loopback_neigh->dev) {
+			if (!rose_loopback_neigh->dev &&
+			    !rose_loopback_neigh->loopback) {
 				kfree_skb(skb);
 				continue;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/net/rose/rose_route.c
+++ linux-xilinx-zynqmp-5.15.0/net/rose/rose_route.c
@@ -227,8 +227,8 @@
 {
 	struct rose_neigh *s;
 
-	rose_stop_ftimer(rose_neigh);
-	rose_stop_t0timer(rose_neigh);
+	del_timer_sync(&rose_neigh->ftimer);
+	del_timer_sync(&rose_neigh->t0timer);
 
 	skb_queue_purge(&rose_neigh->queue);
 
@@ -615,6 +615,8 @@
 			if (first == NULL || strncmp(dev->name, first->name, 3) < 0)
 				first = dev;
 	}
+	if (first)
+		dev_hold(first);
 	rcu_read_unlock();
 
 	return first;
--- linux-xilinx-zynqmp-5.15.0.orig/net/rose/rose_timer.c
+++ linux-xilinx-zynqmp-5.15.0/net/rose/rose_timer.c
@@ -31,89 +31,89 @@
 
 void rose_start_heartbeat(struct sock *sk)
 {
-	del_timer(&sk->sk_timer);
+	sk_stop_timer(sk, &sk->sk_timer);
 
 	sk->sk_timer.function = rose_heartbeat_expiry;
 	sk->sk_timer.expires  = jiffies + 5 * HZ;
 
-	add_timer(&sk->sk_timer);
+	sk_reset_timer(sk, &sk->sk_timer, sk->sk_timer.expires);
 }
 
 void rose_start_t1timer(struct sock *sk)
 {
 	struct rose_sock *rose = rose_sk(sk);
 
-	del_timer(&rose->timer);
+	sk_stop_timer(sk, &rose->timer);
 
 	rose->timer.function = rose_timer_expiry;
 	rose->timer.expires  = jiffies + rose->t1;
 
-	add_timer(&rose->timer);
+	sk_reset_timer(sk, &rose->timer, rose->timer.expires);
 }
 
 void rose_start_t2timer(struct sock *sk)
 {
 	struct rose_sock *rose = rose_sk(sk);
 
-	del_timer(&rose->timer);
+	sk_stop_timer(sk, &rose->timer);
 
 	rose->timer.function = rose_timer_expiry;
 	rose->timer.expires  = jiffies + rose->t2;
 
-	add_timer(&rose->timer);
+	sk_reset_timer(sk, &rose->timer, rose->timer.expires);
 }
 
 void rose_start_t3timer(struct sock *sk)
 {
 	struct rose_sock *rose = rose_sk(sk);
 
-	del_timer(&rose->timer);
+	sk_stop_timer(sk, &rose->timer);
 
 	rose->timer.function = rose_timer_expiry;
 	rose->timer.expires  = jiffies + rose->t3;
 
-	add_timer(&rose->timer);
+	sk_reset_timer(sk, &rose->timer, rose->timer.expires);
 }
 
 void rose_start_hbtimer(struct sock *sk)
 {
 	struct rose_sock *rose = rose_sk(sk);
 
-	del_timer(&rose->timer);
+	sk_stop_timer(sk, &rose->timer);
 
 	rose->timer.function = rose_timer_expiry;
 	rose->timer.expires  = jiffies + rose->hb;
 
-	add_timer(&rose->timer);
+	sk_reset_timer(sk, &rose->timer, rose->timer.expires);
 }
 
 void rose_start_idletimer(struct sock *sk)
 {
 	struct rose_sock *rose = rose_sk(sk);
 
-	del_timer(&rose->idletimer);
+	sk_stop_timer(sk, &rose->idletimer);
 
 	if (rose->idle > 0) {
 		rose->idletimer.function = rose_idletimer_expiry;
 		rose->idletimer.expires  = jiffies + rose->idle;
 
-		add_timer(&rose->idletimer);
+		sk_reset_timer(sk, &rose->idletimer, rose->idletimer.expires);
 	}
 }
 
 void rose_stop_heartbeat(struct sock *sk)
 {
-	del_timer(&sk->sk_timer);
+	sk_stop_timer(sk, &sk->sk_timer);
 }
 
 void rose_stop_timer(struct sock *sk)
 {
-	del_timer(&rose_sk(sk)->timer);
+	sk_stop_timer(sk, &rose_sk(sk)->timer);
 }
 
 void rose_stop_idletimer(struct sock *sk)
 {
-	del_timer(&rose_sk(sk)->idletimer);
+	sk_stop_timer(sk, &rose_sk(sk)->idletimer);
 }
 
 static void rose_heartbeat_expiry(struct timer_list *t)
@@ -122,6 +122,10 @@
 	struct rose_sock *rose = rose_sk(sk);
 
 	bh_lock_sock(sk);
+	if (sock_owned_by_user(sk)) {
+		sk_reset_timer(sk, &sk->sk_timer, jiffies + HZ/20);
+		goto out;
+	}
 	switch (rose->state) {
 	case ROSE_STATE_0:
 		/* Magic here: If we listen() and a new link dies before it
@@ -130,6 +134,7 @@
 		    (sk->sk_state == TCP_LISTEN && sock_flag(sk, SOCK_DEAD))) {
 			bh_unlock_sock(sk);
 			rose_destroy_socket(sk);
+			sock_put(sk);
 			return;
 		}
 		break;
@@ -151,7 +156,9 @@
 	}
 
 	rose_start_heartbeat(sk);
+out:
 	bh_unlock_sock(sk);
+	sock_put(sk);
 }
 
 static void rose_timer_expiry(struct timer_list *t)
@@ -160,6 +167,10 @@
 	struct sock *sk = &rose->sock;
 
 	bh_lock_sock(sk);
+	if (sock_owned_by_user(sk)) {
+		sk_reset_timer(sk, &rose->timer, jiffies + HZ/20);
+		goto out;
+	}
 	switch (rose->state) {
 	case ROSE_STATE_1:	/* T1 */
 	case ROSE_STATE_4:	/* T2 */
@@ -180,7 +191,9 @@
 		}
 		break;
 	}
+out:
 	bh_unlock_sock(sk);
+	sock_put(sk);
 }
 
 static void rose_idletimer_expiry(struct timer_list *t)
@@ -189,6 +202,10 @@
 	struct sock *sk = &rose->sock;
 
 	bh_lock_sock(sk);
+	if (sock_owned_by_user(sk)) {
+		sk_reset_timer(sk, &rose->idletimer, jiffies + HZ/20);
+		goto out;
+	}
 	rose_clear_queues(sk);
 
 	rose_write_internal(sk, ROSE_CLEAR_REQUEST);
@@ -204,5 +221,7 @@
 		sk->sk_state_change(sk);
 		sock_set_flag(sk, SOCK_DEAD);
 	}
+out:
 	bh_unlock_sock(sk);
+	sock_put(sk);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/af_rxrpc.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/af_rxrpc.c
@@ -351,7 +351,7 @@
  */
 void rxrpc_kernel_end_call(struct socket *sock, struct rxrpc_call *call)
 {
-	_enter("%d{%d}", call->debug_id, atomic_read(&call->usage));
+	_enter("%d{%d}", call->debug_id, refcount_read(&call->ref));
 
 	mutex_lock(&call->user_mutex);
 	rxrpc_release_call(rxrpc_sk(sock->sk), call);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/ar-internal.h
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/ar-internal.h
@@ -15,14 +15,6 @@
 #include <keys/rxrpc-type.h>
 #include "protocol.h"
 
-#if 0
-#define CHECK_SLAB_OKAY(X)				     \
-	BUG_ON(atomic_read((X)) >> (sizeof(atomic_t) - 2) == \
-	       (POISON_FREE << 8 | POISON_FREE))
-#else
-#define CHECK_SLAB_OKAY(X) do {} while (0)
-#endif
-
 #define FCRYPT_BSIZE 8
 struct rxrpc_crypt {
 	union {
@@ -68,7 +60,7 @@
 	struct proc_dir_entry	*proc_net;	/* Subdir in /proc/net */
 	u32			epoch;		/* Local epoch for detecting local-end reset */
 	struct list_head	calls;		/* List of calls active in this namespace */
-	rwlock_t		call_lock;	/* Lock for ->calls */
+	spinlock_t		call_lock;	/* Lock for ->calls */
 	atomic_t		nr_calls;	/* Count of allocated calls */
 
 	atomic_t		nr_conns;
@@ -88,7 +80,7 @@
 	struct work_struct	client_conn_reaper;
 	struct timer_list	client_conn_reap_timer;
 
-	struct list_head	local_endpoints;
+	struct hlist_head	local_endpoints;
 	struct mutex		local_mutex;	/* Lock for ->local_endpoints */
 
 	DECLARE_HASHTABLE	(peer_hash, 10);
@@ -279,9 +271,9 @@
 struct rxrpc_local {
 	struct rcu_head		rcu;
 	atomic_t		active_users;	/* Number of users of the local endpoint */
-	atomic_t		usage;		/* Number of references to the structure */
+	refcount_t		ref;		/* Number of references to the structure */
 	struct rxrpc_net	*rxnet;		/* The network ns in which this resides */
-	struct list_head	link;
+	struct hlist_node	link;
 	struct socket		*socket;	/* my UDP socket */
 	struct work_struct	processor;
 	struct rxrpc_sock __rcu	*service;	/* Service(s) listening on this endpoint */
@@ -304,7 +296,7 @@
  */
 struct rxrpc_peer {
 	struct rcu_head		rcu;		/* This must be first */
-	atomic_t		usage;
+	refcount_t		ref;
 	unsigned long		hash_key;
 	struct hlist_node	hash_link;
 	struct rxrpc_local	*local;
@@ -406,7 +398,8 @@
  */
 struct rxrpc_bundle {
 	struct rxrpc_conn_parameters params;
-	atomic_t		usage;
+	refcount_t		ref;
+	atomic_t		active;		/* Number of active users */
 	unsigned int		debug_id;
 	bool			try_upgrade;	/* True if the bundle is attempting upgrade */
 	bool			alloc_conn;	/* True if someone's getting a conn */
@@ -427,7 +420,7 @@
 	struct rxrpc_conn_proto	proto;
 	struct rxrpc_conn_parameters params;
 
-	atomic_t		usage;
+	refcount_t		ref;
 	struct rcu_head		rcu;
 	struct list_head	cache_link;
 
@@ -609,7 +602,7 @@
 	int			error;		/* Local error incurred */
 	enum rxrpc_call_state	state;		/* current state of call */
 	enum rxrpc_call_completion completion;	/* Call completion condition */
-	atomic_t		usage;
+	refcount_t		ref;
 	u16			service_id;	/* service ID */
 	u8			security_ix;	/* Security type */
 	enum rxrpc_interruptibility interruptibility; /* At what point call may be interrupted */
@@ -676,13 +669,11 @@
 
 	spinlock_t		input_lock;	/* Lock for packet input to this call */
 
-	/* receive-phase ACK management */
+	/* Receive-phase ACK management (ACKs we send). */
 	u8			ackr_reason;	/* reason to ACK */
-	rxrpc_serial_t		ackr_serial;	/* serial of packet being ACK'd */
-	rxrpc_serial_t		ackr_first_seq;	/* first sequence number received */
-	rxrpc_seq_t		ackr_prev_seq;	/* previous sequence number received */
-	rxrpc_seq_t		ackr_consumed;	/* Highest packet shown consumed */
-	rxrpc_seq_t		ackr_seen;	/* Highest packet shown seen */
+	rxrpc_seq_t		ackr_highest_seq; /* Higest sequence number received */
+	atomic_t		ackr_nr_unacked; /* Number of unacked packets */
+	atomic_t		ackr_nr_consumed; /* Number of packets needing hard ACK */
 
 	/* RTT management */
 	rxrpc_serial_t		rtt_serial[4];	/* Serial number of DATA or PING sent */
@@ -692,8 +683,10 @@
 #define RXRPC_CALL_RTT_AVAIL_MASK	0xf
 #define RXRPC_CALL_RTT_PEND_SHIFT	8
 
-	/* transmission-phase ACK management */
+	/* Transmission-phase ACK management (ACKs we've received). */
 	ktime_t			acks_latest_ts;	/* Timestamp of latest ACK received */
+	rxrpc_seq_t		acks_first_seq;	/* first sequence number received */
+	rxrpc_seq_t		acks_prev_seq;	/* Highest previousPacket received */
 	rxrpc_seq_t		acks_lowest_nak; /* Lowest NACK in the buffer (or ==tx_hard_ack) */
 	rxrpc_seq_t		acks_lost_top;	/* tx_top at the time lost-ack ping sent */
 	rxrpc_serial_t		acks_lost_ping;	/* Serial number of probe ACK */
@@ -777,14 +770,12 @@
 		       enum rxrpc_propose_ack_trace);
 void rxrpc_process_call(struct work_struct *);
 
-static inline void rxrpc_reduce_call_timer(struct rxrpc_call *call,
-					   unsigned long expire_at,
-					   unsigned long now,
-					   enum rxrpc_timer_trace why)
-{
-	trace_rxrpc_timer(call, why, now);
-	timer_reduce(&call->timer, expire_at);
-}
+void rxrpc_reduce_call_timer(struct rxrpc_call *call,
+			     unsigned long expire_at,
+			     unsigned long now,
+			     enum rxrpc_timer_trace why);
+
+void rxrpc_delete_call_timer(struct rxrpc_call *call);
 
 /*
  * call_object.c
@@ -808,6 +799,7 @@
 bool __rxrpc_queue_call(struct rxrpc_call *);
 bool rxrpc_queue_call(struct rxrpc_call *);
 void rxrpc_see_call(struct rxrpc_call *);
+bool rxrpc_try_get_call(struct rxrpc_call *call, enum rxrpc_call_trace op);
 void rxrpc_get_call(struct rxrpc_call *, enum rxrpc_call_trace);
 void rxrpc_put_call(struct rxrpc_call *, enum rxrpc_call_trace);
 void rxrpc_cleanup_call(struct rxrpc_call *);
@@ -990,6 +982,7 @@
 /*
  * peer_event.c
  */
+void rxrpc_encap_err_rcv(struct sock *sk, struct sk_buff *skb, unsigned int udp_offset);
 void rxrpc_error_report(struct sock *);
 void rxrpc_peer_keepalive_worker(struct work_struct *);
 
@@ -1015,6 +1008,7 @@
 extern const struct seq_operations rxrpc_call_seq_ops;
 extern const struct seq_operations rxrpc_connection_seq_ops;
 extern const struct seq_operations rxrpc_peer_seq_ops;
+extern const struct seq_operations rxrpc_local_seq_ops;
 
 /*
  * recvmsg.c
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/call_accept.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/call_accept.c
@@ -91,7 +91,7 @@
 				  (head + 1) & (size - 1));
 
 		trace_rxrpc_conn(conn->debug_id, rxrpc_conn_new_service,
-				 atomic_read(&conn->usage), here);
+				 refcount_read(&conn->ref), here);
 	}
 
 	/* Now it gets complicated, because calls get registered with the
@@ -104,7 +104,7 @@
 	call->state = RXRPC_CALL_SERVER_PREALLOC;
 
 	trace_rxrpc_call(call->debug_id, rxrpc_call_new_service,
-			 atomic_read(&call->usage),
+			 refcount_read(&call->ref),
 			 here, (const void *)user_call_ID);
 
 	write_lock(&rx->call_lock);
@@ -140,9 +140,9 @@
 	write_unlock(&rx->call_lock);
 
 	rxnet = call->rxnet;
-	write_lock(&rxnet->call_lock);
-	list_add_tail(&call->link, &rxnet->calls);
-	write_unlock(&rxnet->call_lock);
+	spin_lock_bh(&rxnet->call_lock);
+	list_add_tail_rcu(&call->link, &rxnet->calls);
+	spin_unlock_bh(&rxnet->call_lock);
 
 	b->call_backlog[call_head] = call;
 	smp_store_release(&b->call_backlog_head, (call_head + 1) & (size - 1));
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/call_event.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/call_event.c
@@ -67,13 +67,11 @@
 	if (ack_reason == call->ackr_reason) {
 		if (RXRPC_ACK_UPDATEABLE & (1 << ack_reason)) {
 			outcome = rxrpc_propose_ack_update;
-			call->ackr_serial = serial;
 		}
 		if (!immediate)
 			goto trace;
 	} else if (prior > rxrpc_ack_priority[call->ackr_reason]) {
 		call->ackr_reason = ack_reason;
-		call->ackr_serial = serial;
 	} else {
 		outcome = rxrpc_propose_ack_subsume;
 	}
@@ -157,7 +155,7 @@
 static void rxrpc_resend(struct rxrpc_call *call, unsigned long now_j)
 {
 	struct sk_buff *skb;
-	unsigned long resend_at, rto_j;
+	unsigned long resend_at;
 	rxrpc_seq_t cursor, seq, top;
 	ktime_t now, max_age, oldest, ack_ts;
 	int ix;
@@ -165,10 +163,8 @@
 
 	_enter("{%d,%d}", call->tx_hard_ack, call->tx_top);
 
-	rto_j = call->peer->rto_j;
-
 	now = ktime_get_real();
-	max_age = ktime_sub(now, jiffies_to_usecs(rto_j));
+	max_age = ktime_sub_us(now, jiffies_to_usecs(call->peer->rto_j));
 
 	spin_lock_bh(&call->lock);
 
@@ -213,7 +209,7 @@
 	}
 
 	resend_at = nsecs_to_jiffies(ktime_to_ns(ktime_sub(now, oldest)));
-	resend_at += jiffies + rto_j;
+	resend_at += jiffies + rxrpc_get_rto_backoff(call->peer, retrans);
 	WRITE_ONCE(call->resend_at, resend_at);
 
 	if (unacked)
@@ -312,7 +308,7 @@
 	}
 
 	if (call->state == RXRPC_CALL_COMPLETE) {
-		del_timer_sync(&call->timer);
+		rxrpc_delete_call_timer(call);
 		goto out_put;
 	}
 
@@ -379,9 +375,9 @@
 		if (test_bit(RXRPC_CALL_RX_HEARD, &call->flags) &&
 		    (int)call->conn->hi_serial - (int)call->rx_serial > 0) {
 			trace_rxrpc_call_reset(call);
-			rxrpc_abort_call("EXP", call, 0, RX_USER_ABORT, -ECONNRESET);
+			rxrpc_abort_call("EXP", call, 0, RX_CALL_DEAD, -ECONNRESET);
 		} else {
-			rxrpc_abort_call("EXP", call, 0, RX_USER_ABORT, -ETIME);
+			rxrpc_abort_call("EXP", call, 0, RX_CALL_TIMEOUT, -ETIME);
 		}
 		set_bit(RXRPC_CALL_EV_ABORT, &call->events);
 		goto recheck_state;
@@ -408,7 +404,8 @@
 		goto recheck_state;
 	}
 
-	if (test_and_clear_bit(RXRPC_CALL_EV_RESEND, &call->events)) {
+	if (test_and_clear_bit(RXRPC_CALL_EV_RESEND, &call->events) &&
+	    call->state != RXRPC_CALL_CLIENT_RECV_REPLY) {
 		rxrpc_resend(call, now);
 		goto recheck_state;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/call_object.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/call_object.c
@@ -53,10 +53,30 @@
 
 	if (call->state < RXRPC_CALL_COMPLETE) {
 		trace_rxrpc_timer(call, rxrpc_timer_expired, jiffies);
-		rxrpc_queue_call(call);
+		__rxrpc_queue_call(call);
+	} else {
+		rxrpc_put_call(call, rxrpc_call_put);
 	}
 }
 
+void rxrpc_reduce_call_timer(struct rxrpc_call *call,
+			     unsigned long expire_at,
+			     unsigned long now,
+			     enum rxrpc_timer_trace why)
+{
+	if (rxrpc_try_get_call(call, rxrpc_call_got_timer)) {
+		trace_rxrpc_timer(call, why, now);
+		if (timer_reduce(&call->timer, expire_at))
+			rxrpc_put_call(call, rxrpc_call_put_notimer);
+	}
+}
+
+void rxrpc_delete_call_timer(struct rxrpc_call *call)
+{
+	if (del_timer_sync(&call->timer))
+		rxrpc_put_call(call, rxrpc_call_put_timer);
+}
+
 static struct lock_class_key rxrpc_call_user_mutex_lock_class_key;
 
 /*
@@ -92,7 +112,7 @@
 found_extant_call:
 	rxrpc_get_call(call, rxrpc_call_got);
 	read_unlock(&rx->call_lock);
-	_leave(" = %p [%d]", call, atomic_read(&call->usage));
+	_leave(" = %p [%d]", call, refcount_read(&call->ref));
 	return call;
 }
 
@@ -140,7 +160,7 @@
 	spin_lock_init(&call->notify_lock);
 	spin_lock_init(&call->input_lock);
 	rwlock_init(&call->state_lock);
-	atomic_set(&call->usage, 1);
+	refcount_set(&call->ref, 1);
 	call->debug_id = debug_id;
 	call->tx_total_len = -1;
 	call->next_rx_timo = 20 * HZ;
@@ -265,8 +285,10 @@
 	_enter("%p,%lx", rx, p->user_call_ID);
 
 	limiter = rxrpc_get_call_slot(p, gfp);
-	if (!limiter)
+	if (!limiter) {
+		release_sock(&rx->sk);
 		return ERR_PTR(-ERESTARTSYS);
+	}
 
 	call = rxrpc_alloc_client_call(rx, srx, gfp, debug_id);
 	if (IS_ERR(call)) {
@@ -279,7 +301,7 @@
 	call->interruptibility = p->interruptibility;
 	call->tx_total_len = p->tx_total_len;
 	trace_rxrpc_call(call->debug_id, rxrpc_call_new_client,
-			 atomic_read(&call->usage),
+			 refcount_read(&call->ref),
 			 here, (const void *)p->user_call_ID);
 	if (p->kernel)
 		__set_bit(RXRPC_CALL_KERNEL, &call->flags);
@@ -317,9 +339,9 @@
 	write_unlock(&rx->call_lock);
 
 	rxnet = call->rxnet;
-	write_lock(&rxnet->call_lock);
-	list_add_tail(&call->link, &rxnet->calls);
-	write_unlock(&rxnet->call_lock);
+	spin_lock_bh(&rxnet->call_lock);
+	list_add_tail_rcu(&call->link, &rxnet->calls);
+	spin_unlock_bh(&rxnet->call_lock);
 
 	/* From this point on, the call is protected by its own lock. */
 	release_sock(&rx->sk);
@@ -332,7 +354,7 @@
 		goto error_attached_to_socket;
 
 	trace_rxrpc_call(call->debug_id, rxrpc_call_connected,
-			 atomic_read(&call->usage), here, NULL);
+			 refcount_read(&call->ref), here, NULL);
 
 	rxrpc_start_call_timer(call);
 
@@ -352,7 +374,7 @@
 	__rxrpc_set_call_completion(call, RXRPC_CALL_LOCAL_ERROR,
 				    RX_CALL_DEAD, -EEXIST);
 	trace_rxrpc_call(call->debug_id, rxrpc_call_error,
-			 atomic_read(&call->usage), here, ERR_PTR(-EEXIST));
+			 refcount_read(&call->ref), here, ERR_PTR(-EEXIST));
 	rxrpc_release_call(rx, call);
 	mutex_unlock(&call->user_mutex);
 	rxrpc_put_call(call, rxrpc_call_put);
@@ -366,7 +388,7 @@
 	 */
 error_attached_to_socket:
 	trace_rxrpc_call(call->debug_id, rxrpc_call_error,
-			 atomic_read(&call->usage), here, ERR_PTR(ret));
+			 refcount_read(&call->ref), here, ERR_PTR(ret));
 	set_bit(RXRPC_CALL_DISCONNECTED, &call->flags);
 	__rxrpc_set_call_completion(call, RXRPC_CALL_LOCAL_ERROR,
 				    RX_CALL_DEAD, ret);
@@ -422,8 +444,9 @@
 bool rxrpc_queue_call(struct rxrpc_call *call)
 {
 	const void *here = __builtin_return_address(0);
-	int n = atomic_fetch_add_unless(&call->usage, 1, 0);
-	if (n == 0)
+	int n;
+
+	if (!__refcount_inc_not_zero(&call->ref, &n))
 		return false;
 	if (rxrpc_queue_work(&call->processor))
 		trace_rxrpc_call(call->debug_id, rxrpc_call_queued, n + 1,
@@ -439,7 +462,7 @@
 bool __rxrpc_queue_call(struct rxrpc_call *call)
 {
 	const void *here = __builtin_return_address(0);
-	int n = atomic_read(&call->usage);
+	int n = refcount_read(&call->ref);
 	ASSERTCMP(n, >=, 1);
 	if (rxrpc_queue_work(&call->processor))
 		trace_rxrpc_call(call->debug_id, rxrpc_call_queued_ref, n,
@@ -456,22 +479,34 @@
 {
 	const void *here = __builtin_return_address(0);
 	if (call) {
-		int n = atomic_read(&call->usage);
+		int n = refcount_read(&call->ref);
 
 		trace_rxrpc_call(call->debug_id, rxrpc_call_seen, n,
 				 here, NULL);
 	}
 }
 
+bool rxrpc_try_get_call(struct rxrpc_call *call, enum rxrpc_call_trace op)
+{
+	const void *here = __builtin_return_address(0);
+	int n;
+
+	if (!__refcount_inc_not_zero(&call->ref, &n))
+		return false;
+	trace_rxrpc_call(call->debug_id, op, n + 1, here, NULL);
+	return true;
+}
+
 /*
  * Note the addition of a ref on a call.
  */
 void rxrpc_get_call(struct rxrpc_call *call, enum rxrpc_call_trace op)
 {
 	const void *here = __builtin_return_address(0);
-	int n = atomic_inc_return(&call->usage);
+	int n;
 
-	trace_rxrpc_call(call->debug_id, op, n, here, NULL);
+	__refcount_inc(&call->ref, &n);
+	trace_rxrpc_call(call->debug_id, op, n + 1, here, NULL);
 }
 
 /*
@@ -496,10 +531,10 @@
 	struct rxrpc_connection *conn = call->conn;
 	bool put = false;
 
-	_enter("{%d,%d}", call->debug_id, atomic_read(&call->usage));
+	_enter("{%d,%d}", call->debug_id, refcount_read(&call->ref));
 
 	trace_rxrpc_call(call->debug_id, rxrpc_call_release,
-			 atomic_read(&call->usage),
+			 refcount_read(&call->ref),
 			 here, (const void *)call->flags);
 
 	ASSERTCMP(call->state, ==, RXRPC_CALL_COMPLETE);
@@ -510,8 +545,7 @@
 	spin_unlock_bh(&call->lock);
 
 	rxrpc_put_call_slot(call);
-
-	del_timer_sync(&call->timer);
+	rxrpc_delete_call_timer(call);
 
 	/* Make sure we don't get any more notifications */
 	write_lock_bh(&rx->recvmsg_lock);
@@ -589,21 +623,21 @@
 	struct rxrpc_net *rxnet = call->rxnet;
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id = call->debug_id;
+	bool dead;
 	int n;
 
 	ASSERT(call != NULL);
 
-	n = atomic_dec_return(&call->usage);
+	dead = __refcount_dec_and_test(&call->ref, &n);
 	trace_rxrpc_call(debug_id, op, n, here, NULL);
-	ASSERTCMP(n, >=, 0);
-	if (n == 0) {
+	if (dead) {
 		_debug("call %d dead", call->debug_id);
 		ASSERTCMP(call->state, ==, RXRPC_CALL_COMPLETE);
 
 		if (!list_empty(&call->link)) {
-			write_lock(&rxnet->call_lock);
+			spin_lock_bh(&rxnet->call_lock);
 			list_del_init(&call->link);
-			write_unlock(&rxnet->call_lock);
+			spin_unlock_bh(&rxnet->call_lock);
 		}
 
 		rxrpc_cleanup_call(call);
@@ -618,6 +652,8 @@
 	struct rxrpc_call *call = container_of(work, struct rxrpc_call, processor);
 	struct rxrpc_net *rxnet = call->rxnet;
 
+	rxrpc_delete_call_timer(call);
+
 	rxrpc_put_connection(call->conn);
 	rxrpc_put_peer(call->peer);
 	kfree(call->rxtx_buffer);
@@ -652,8 +688,6 @@
 
 	memset(&call->sock_node, 0xcd, sizeof(call->sock_node));
 
-	del_timer_sync(&call->timer);
-
 	ASSERTCMP(call->state, ==, RXRPC_CALL_COMPLETE);
 	ASSERT(test_bit(RXRPC_CALL_RELEASED, &call->flags));
 
@@ -675,7 +709,7 @@
 	_enter("");
 
 	if (!list_empty(&rxnet->calls)) {
-		write_lock(&rxnet->call_lock);
+		spin_lock_bh(&rxnet->call_lock);
 
 		while (!list_empty(&rxnet->calls)) {
 			call = list_entry(rxnet->calls.next,
@@ -686,16 +720,16 @@
 			list_del_init(&call->link);
 
 			pr_err("Call %p still in use (%d,%s,%lx,%lx)!\n",
-			       call, atomic_read(&call->usage),
+			       call, refcount_read(&call->ref),
 			       rxrpc_call_states[call->state],
 			       call->flags, call->events);
 
-			write_unlock(&rxnet->call_lock);
+			spin_unlock_bh(&rxnet->call_lock);
 			cond_resched();
-			write_lock(&rxnet->call_lock);
+			spin_lock_bh(&rxnet->call_lock);
 		}
 
-		write_unlock(&rxnet->call_lock);
+		spin_unlock_bh(&rxnet->call_lock);
 	}
 
 	atomic_dec(&rxnet->nr_calls);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/conn_client.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/conn_client.c
@@ -40,6 +40,8 @@
 DEFINE_IDR(rxrpc_client_conn_ids);
 static DEFINE_SPINLOCK(rxrpc_conn_id_lock);
 
+static void rxrpc_deactivate_bundle(struct rxrpc_bundle *bundle);
+
 /*
  * Get a connection ID and epoch for a client connection from the global pool.
  * The connection struct pointer is then recorded in the idr radix tree.  The
@@ -102,7 +104,7 @@
 	if (!idr_is_empty(&rxrpc_client_conn_ids)) {
 		idr_for_each_entry(&rxrpc_client_conn_ids, conn, id) {
 			pr_err("AF_RXRPC: Leaked client conn %p {%d}\n",
-			       conn, atomic_read(&conn->usage));
+			       conn, refcount_read(&conn->ref));
 		}
 		BUG();
 	}
@@ -122,7 +124,8 @@
 	if (bundle) {
 		bundle->params = *cp;
 		rxrpc_get_peer(bundle->params.peer);
-		atomic_set(&bundle->usage, 1);
+		refcount_set(&bundle->ref, 1);
+		atomic_set(&bundle->active, 1);
 		spin_lock_init(&bundle->channel_lock);
 		INIT_LIST_HEAD(&bundle->waiting_calls);
 	}
@@ -131,20 +134,27 @@
 
 struct rxrpc_bundle *rxrpc_get_bundle(struct rxrpc_bundle *bundle)
 {
-	atomic_inc(&bundle->usage);
+	refcount_inc(&bundle->ref);
 	return bundle;
 }
 
+static void rxrpc_free_bundle(struct rxrpc_bundle *bundle)
+{
+	rxrpc_put_peer(bundle->params.peer);
+	kfree(bundle);
+}
+
 void rxrpc_put_bundle(struct rxrpc_bundle *bundle)
 {
 	unsigned int d = bundle->debug_id;
-	unsigned int u = atomic_dec_return(&bundle->usage);
+	bool dead;
+	int r;
 
-	_debug("PUT B=%x %u", d, u);
-	if (u == 0) {
-		rxrpc_put_peer(bundle->params.peer);
-		kfree(bundle);
-	}
+	dead = __refcount_dec_and_test(&bundle->ref, &r);
+
+	_debug("PUT B=%x %d", d, r - 1);
+	if (dead)
+		rxrpc_free_bundle(bundle);
 }
 
 /*
@@ -165,7 +175,7 @@
 		return ERR_PTR(-ENOMEM);
 	}
 
-	atomic_set(&conn->usage, 1);
+	refcount_set(&conn->ref, 1);
 	conn->bundle		= bundle;
 	conn->params		= bundle->params;
 	conn->out_clientflag	= RXRPC_CLIENT_INITIATED;
@@ -191,7 +201,7 @@
 	key_get(conn->params.key);
 
 	trace_rxrpc_conn(conn->debug_id, rxrpc_conn_new_client,
-			 atomic_read(&conn->usage),
+			 refcount_read(&conn->ref),
 			 __builtin_return_address(0));
 
 	atomic_inc(&rxnet->nr_client_conns);
@@ -328,9 +338,10 @@
 	return candidate;
 
 found_bundle_free:
-	kfree(candidate);
+	rxrpc_free_bundle(candidate);
 found_bundle:
 	rxrpc_get_bundle(bundle);
+	atomic_inc(&bundle->active);
 	spin_unlock(&local->client_bundles_lock);
 	_leave(" = %u [found]", bundle->debug_id);
 	return bundle;
@@ -428,6 +439,7 @@
 			if (old)
 				trace_rxrpc_client(old, -1, rxrpc_client_replace);
 			candidate->bundle_shift = shift;
+			atomic_inc(&bundle->active);
 			bundle->conns[i] = candidate;
 			for (j = 0; j < RXRPC_MAXCALLS; j++)
 				set_bit(shift + j, &bundle->avail_chans);
@@ -718,6 +730,7 @@
 	smp_rmb();
 
 out_put_bundle:
+	rxrpc_deactivate_bundle(bundle);
 	rxrpc_put_bundle(bundle);
 out:
 	_leave(" = %d", ret);
@@ -893,9 +906,8 @@
 static void rxrpc_unbundle_conn(struct rxrpc_connection *conn)
 {
 	struct rxrpc_bundle *bundle = conn->bundle;
-	struct rxrpc_local *local = bundle->params.local;
 	unsigned int bindex;
-	bool need_drop = false, need_put = false;
+	bool need_drop = false;
 	int i;
 
 	_enter("C=%x", conn->debug_id);
@@ -914,15 +926,22 @@
 	}
 	spin_unlock(&bundle->channel_lock);
 
-	/* If there are no more connections, remove the bundle */
-	if (!bundle->avail_chans) {
-		_debug("maybe unbundle");
-		spin_lock(&local->client_bundles_lock);
-
-		for (i = 0; i < ARRAY_SIZE(bundle->conns); i++)
-			if (bundle->conns[i])
-				break;
-		if (i == ARRAY_SIZE(bundle->conns) && !bundle->params.exclusive) {
+	if (need_drop) {
+		rxrpc_deactivate_bundle(bundle);
+		rxrpc_put_connection(conn);
+	}
+}
+
+/*
+ * Drop the active count on a bundle.
+ */
+static void rxrpc_deactivate_bundle(struct rxrpc_bundle *bundle)
+{
+	struct rxrpc_local *local = bundle->params.local;
+	bool need_put = false;
+
+	if (atomic_dec_and_lock(&bundle->active, &local->client_bundles_lock)) {
+		if (!bundle->params.exclusive) {
 			_debug("erase bundle");
 			rb_erase(&bundle->local_node, &local->client_bundles);
 			need_put = true;
@@ -932,10 +951,6 @@
 		if (need_put)
 			rxrpc_put_bundle(bundle);
 	}
-
-	if (need_drop)
-		rxrpc_put_connection(conn);
-	_leave("");
 }
 
 /*
@@ -962,14 +977,13 @@
 {
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id = conn->debug_id;
-	int n;
+	bool dead;
+	int r;
 
-	n = atomic_dec_return(&conn->usage);
-	trace_rxrpc_conn(debug_id, rxrpc_conn_put_client, n, here);
-	if (n <= 0) {
-		ASSERTCMP(n, >=, 0);
+	dead = __refcount_dec_and_test(&conn->ref, &r);
+	trace_rxrpc_conn(debug_id, rxrpc_conn_put_client, r - 1, here);
+	if (dead)
 		rxrpc_kill_client_conn(conn);
-	}
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/conn_event.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/conn_event.c
@@ -41,6 +41,14 @@
 
 	_enter("%d", conn->debug_id);
 
+	if (sp && sp->hdr.type == RXRPC_PACKET_TYPE_ACK) {
+		if (skb_copy_bits(skb, sizeof(struct rxrpc_wire_header),
+				  &pkt.ack, sizeof(pkt.ack)) < 0)
+			return;
+		if (pkt.ack.reason == RXRPC_ACK_PING_RESPONSE)
+			return;
+	}
+
 	chan = &conn->channels[channel];
 
 	/* If the last call got moved on whilst we were waiting to run, just
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/conn_object.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/conn_object.c
@@ -104,7 +104,7 @@
 			goto not_found;
 		*_peer = peer;
 		conn = rxrpc_find_service_conn_rcu(peer, skb);
-		if (!conn || atomic_read(&conn->usage) == 0)
+		if (!conn || refcount_read(&conn->ref) == 0)
 			goto not_found;
 		_leave(" = %p", conn);
 		return conn;
@@ -114,7 +114,7 @@
 		 */
 		conn = idr_find(&rxrpc_client_conn_ids,
 				sp->hdr.cid >> RXRPC_CIDSHIFT);
-		if (!conn || atomic_read(&conn->usage) == 0) {
+		if (!conn || refcount_read(&conn->ref) == 0) {
 			_debug("no conn");
 			goto not_found;
 		}
@@ -183,7 +183,7 @@
 			chan->last_type = RXRPC_PACKET_TYPE_ABORT;
 			break;
 		default:
-			chan->last_abort = RX_USER_ABORT;
+			chan->last_abort = RX_CALL_DEAD;
 			chan->last_type = RXRPC_PACKET_TYPE_ABORT;
 			break;
 		}
@@ -263,11 +263,12 @@
 bool rxrpc_queue_conn(struct rxrpc_connection *conn)
 {
 	const void *here = __builtin_return_address(0);
-	int n = atomic_fetch_add_unless(&conn->usage, 1, 0);
-	if (n == 0)
+	int r;
+
+	if (!__refcount_inc_not_zero(&conn->ref, &r))
 		return false;
 	if (rxrpc_queue_work(&conn->processor))
-		trace_rxrpc_conn(conn->debug_id, rxrpc_conn_queued, n + 1, here);
+		trace_rxrpc_conn(conn->debug_id, rxrpc_conn_queued, r + 1, here);
 	else
 		rxrpc_put_connection(conn);
 	return true;
@@ -280,7 +281,7 @@
 {
 	const void *here = __builtin_return_address(0);
 	if (conn) {
-		int n = atomic_read(&conn->usage);
+		int n = refcount_read(&conn->ref);
 
 		trace_rxrpc_conn(conn->debug_id, rxrpc_conn_seen, n, here);
 	}
@@ -292,9 +293,10 @@
 struct rxrpc_connection *rxrpc_get_connection(struct rxrpc_connection *conn)
 {
 	const void *here = __builtin_return_address(0);
-	int n = atomic_inc_return(&conn->usage);
+	int r;
 
-	trace_rxrpc_conn(conn->debug_id, rxrpc_conn_got, n, here);
+	__refcount_inc(&conn->ref, &r);
+	trace_rxrpc_conn(conn->debug_id, rxrpc_conn_got, r, here);
 	return conn;
 }
 
@@ -305,11 +307,11 @@
 rxrpc_get_connection_maybe(struct rxrpc_connection *conn)
 {
 	const void *here = __builtin_return_address(0);
+	int r;
 
 	if (conn) {
-		int n = atomic_fetch_add_unless(&conn->usage, 1, 0);
-		if (n > 0)
-			trace_rxrpc_conn(conn->debug_id, rxrpc_conn_got, n + 1, here);
+		if (__refcount_inc_not_zero(&conn->ref, &r))
+			trace_rxrpc_conn(conn->debug_id, rxrpc_conn_got, r + 1, here);
 		else
 			conn = NULL;
 	}
@@ -333,12 +335,11 @@
 {
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id = conn->debug_id;
-	int n;
+	int r;
 
-	n = atomic_dec_return(&conn->usage);
-	trace_rxrpc_conn(debug_id, rxrpc_conn_put_service, n, here);
-	ASSERTCMP(n, >=, 0);
-	if (n == 1)
+	__refcount_dec(&conn->ref, &r);
+	trace_rxrpc_conn(debug_id, rxrpc_conn_put_service, r - 1, here);
+	if (r - 1 == 1)
 		rxrpc_set_service_reap_timer(conn->params.local->rxnet,
 					     jiffies + rxrpc_connection_expiry);
 }
@@ -351,9 +352,9 @@
 	struct rxrpc_connection *conn =
 		container_of(rcu, struct rxrpc_connection, rcu);
 
-	_enter("{%d,u=%d}", conn->debug_id, atomic_read(&conn->usage));
+	_enter("{%d,u=%d}", conn->debug_id, refcount_read(&conn->ref));
 
-	ASSERTCMP(atomic_read(&conn->usage), ==, 0);
+	ASSERTCMP(refcount_read(&conn->ref), ==, 0);
 
 	_net("DESTROY CONN %d", conn->debug_id);
 
@@ -392,8 +393,8 @@
 
 	write_lock(&rxnet->conn_lock);
 	list_for_each_entry_safe(conn, _p, &rxnet->service_conns, link) {
-		ASSERTCMP(atomic_read(&conn->usage), >, 0);
-		if (likely(atomic_read(&conn->usage) > 1))
+		ASSERTCMP(refcount_read(&conn->ref), >, 0);
+		if (likely(refcount_read(&conn->ref) > 1))
 			continue;
 		if (conn->state == RXRPC_CONN_SERVICE_PREALLOC)
 			continue;
@@ -405,7 +406,7 @@
 				expire_at = idle_timestamp + rxrpc_closed_conn_expiry * HZ;
 
 			_debug("reap CONN %d { u=%d,t=%ld }",
-			       conn->debug_id, atomic_read(&conn->usage),
+			       conn->debug_id, refcount_read(&conn->ref),
 			       (long)expire_at - (long)now);
 
 			if (time_before(now, expire_at)) {
@@ -418,7 +419,7 @@
 		/* The usage count sits at 1 whilst the object is unused on the
 		 * list; we reduce that to 0 to make the object unavailable.
 		 */
-		if (atomic_cmpxchg(&conn->usage, 1, 0) != 1)
+		if (!refcount_dec_if_one(&conn->ref))
 			continue;
 		trace_rxrpc_conn(conn->debug_id, rxrpc_conn_reap_service, 0, NULL);
 
@@ -442,7 +443,7 @@
 				  link);
 		list_del_init(&conn->link);
 
-		ASSERTCMP(atomic_read(&conn->usage), ==, 0);
+		ASSERTCMP(refcount_read(&conn->ref), ==, 0);
 		rxrpc_kill_connection(conn);
 	}
 
@@ -470,7 +471,7 @@
 	write_lock(&rxnet->conn_lock);
 	list_for_each_entry_safe(conn, _p, &rxnet->service_conns, link) {
 		pr_err("AF_RXRPC: Leaked conn %p {%d}\n",
-		       conn, atomic_read(&conn->usage));
+		       conn, refcount_read(&conn->ref));
 		leak = true;
 	}
 	write_unlock(&rxnet->conn_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/conn_service.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/conn_service.c
@@ -9,7 +9,7 @@
 #include "ar-internal.h"
 
 static struct rxrpc_bundle rxrpc_service_dummy_bundle = {
-	.usage		= ATOMIC_INIT(1),
+	.ref		= REFCOUNT_INIT(1),
 	.debug_id	= UINT_MAX,
 	.channel_lock	= __SPIN_LOCK_UNLOCKED(&rxrpc_service_dummy_bundle.channel_lock),
 };
@@ -31,7 +31,7 @@
 	struct rxrpc_conn_proto k;
 	struct rxrpc_skb_priv *sp = rxrpc_skb(skb);
 	struct rb_node *p;
-	unsigned int seq = 0;
+	unsigned int seq = 1;
 
 	k.epoch	= sp->hdr.epoch;
 	k.cid	= sp->hdr.cid & RXRPC_CIDMASK;
@@ -41,6 +41,7 @@
 		 * under just the RCU read lock, so we have to check for
 		 * changes.
 		 */
+		seq++; /* 2 on the 1st/lockless path, otherwise odd */
 		read_seqbegin_or_lock(&peer->service_conn_lock, &seq);
 
 		p = rcu_dereference_raw(peer->service_conns.rb_node);
@@ -99,7 +100,7 @@
 	return;
 
 found_extant_conn:
-	if (atomic_read(&cursor->usage) == 0)
+	if (refcount_read(&cursor->ref) == 0)
 		goto replace_old_connection;
 	write_sequnlock_bh(&peer->service_conn_lock);
 	/* We should not be able to get here.  rxrpc_incoming_connection() is
@@ -132,7 +133,7 @@
 		 * the rxrpc_connections list.
 		 */
 		conn->state = RXRPC_CONN_SERVICE_PREALLOC;
-		atomic_set(&conn->usage, 2);
+		refcount_set(&conn->ref, 2);
 		conn->bundle = rxrpc_get_bundle(&rxrpc_service_dummy_bundle);
 
 		atomic_inc(&rxnet->nr_conns);
@@ -142,7 +143,7 @@
 		write_unlock(&rxnet->conn_lock);
 
 		trace_rxrpc_conn(conn->debug_id, rxrpc_conn_new_service,
-				 atomic_read(&conn->usage),
+				 refcount_read(&conn->ref),
 				 __builtin_return_address(0));
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/input.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/input.c
@@ -412,8 +412,8 @@
 {
 	struct rxrpc_skb_priv *sp = rxrpc_skb(skb);
 	enum rxrpc_call_state state;
-	unsigned int j, nr_subpackets;
-	rxrpc_serial_t serial = sp->hdr.serial, ack_serial = 0;
+	unsigned int j, nr_subpackets, nr_unacked = 0;
+	rxrpc_serial_t serial = sp->hdr.serial, ack_serial = serial;
 	rxrpc_seq_t seq0 = sp->hdr.seq, hard_ack;
 	bool immediate_ack = false, jumbo_bad = false;
 	u8 ack = 0;
@@ -453,7 +453,6 @@
 	    !rxrpc_receiving_reply(call))
 		goto unlock;
 
-	call->ackr_prev_seq = seq0;
 	hard_ack = READ_ONCE(call->rx_hard_ack);
 
 	nr_subpackets = sp->nr_subpackets;
@@ -534,6 +533,9 @@
 			ack_serial = serial;
 		}
 
+		if (after(seq0, call->ackr_highest_seq))
+			call->ackr_highest_seq = seq0;
+
 		/* Queue the packet.  We use a couple of memory barriers here as need
 		 * to make sure that rx_top is perceived to be set after the buffer
 		 * pointer and that the buffer pointer is set after the annotation and
@@ -567,6 +569,8 @@
 			sp = NULL;
 		}
 
+		nr_unacked++;
+
 		if (last) {
 			set_bit(RXRPC_CALL_RX_LAST, &call->flags);
 			if (!ack) {
@@ -586,9 +590,14 @@
 			}
 			call->rx_expect_next = seq + 1;
 		}
+		if (!ack)
+			ack_serial = serial;
 	}
 
 ack:
+	if (atomic_add_return(nr_unacked, &call->ackr_nr_unacked) > 2 && !ack)
+		ack = RXRPC_ACK_IDLE;
+
 	if (ack)
 		rxrpc_propose_ACK(call, ack, ack_serial,
 				  immediate_ack, true,
@@ -812,7 +821,7 @@
 static bool rxrpc_is_ack_valid(struct rxrpc_call *call,
 			       rxrpc_seq_t first_pkt, rxrpc_seq_t prev_pkt)
 {
-	rxrpc_seq_t base = READ_ONCE(call->ackr_first_seq);
+	rxrpc_seq_t base = READ_ONCE(call->acks_first_seq);
 
 	if (after(first_pkt, base))
 		return true; /* The window advanced */
@@ -820,7 +829,7 @@
 	if (before(first_pkt, base))
 		return false; /* firstPacket regressed */
 
-	if (after_eq(prev_pkt, call->ackr_prev_seq))
+	if (after_eq(prev_pkt, call->acks_prev_seq))
 		return true; /* previousPacket hasn't regressed. */
 
 	/* Some rx implementations put a serial number in previousPacket. */
@@ -903,11 +912,38 @@
 				  rxrpc_propose_ack_respond_to_ack);
 	}
 
+	/* If we get an EXCEEDS_WINDOW ACK from the server, it probably
+	 * indicates that the client address changed due to NAT.  The server
+	 * lost the call because it switched to a different peer.
+	 */
+	if (unlikely(buf.ack.reason == RXRPC_ACK_EXCEEDS_WINDOW) &&
+	    first_soft_ack == 1 &&
+	    prev_pkt == 0 &&
+	    rxrpc_is_client_call(call)) {
+		rxrpc_set_call_completion(call, RXRPC_CALL_REMOTELY_ABORTED,
+					  0, -ENETRESET);
+		return;
+	}
+
+	/* If we get an OUT_OF_SEQUENCE ACK from the server, that can also
+	 * indicate a change of address.  However, we can retransmit the call
+	 * if we still have it buffered to the beginning.
+	 */
+	if (unlikely(buf.ack.reason == RXRPC_ACK_OUT_OF_SEQUENCE) &&
+	    first_soft_ack == 1 &&
+	    prev_pkt == 0 &&
+	    call->tx_hard_ack == 0 &&
+	    rxrpc_is_client_call(call)) {
+		rxrpc_set_call_completion(call, RXRPC_CALL_REMOTELY_ABORTED,
+					  0, -ENETRESET);
+		return;
+	}
+
 	/* Discard any out-of-order or duplicate ACKs (outside lock). */
 	if (!rxrpc_is_ack_valid(call, first_soft_ack, prev_pkt)) {
 		trace_rxrpc_rx_discard_ack(call->debug_id, ack_serial,
-					   first_soft_ack, call->ackr_first_seq,
-					   prev_pkt, call->ackr_prev_seq);
+					   first_soft_ack, call->acks_first_seq,
+					   prev_pkt, call->acks_prev_seq);
 		return;
 	}
 
@@ -922,14 +958,14 @@
 	/* Discard any out-of-order or duplicate ACKs (inside lock). */
 	if (!rxrpc_is_ack_valid(call, first_soft_ack, prev_pkt)) {
 		trace_rxrpc_rx_discard_ack(call->debug_id, ack_serial,
-					   first_soft_ack, call->ackr_first_seq,
-					   prev_pkt, call->ackr_prev_seq);
+					   first_soft_ack, call->acks_first_seq,
+					   prev_pkt, call->acks_prev_seq);
 		goto out;
 	}
 	call->acks_latest_ts = skb->tstamp;
 
-	call->ackr_first_seq = first_soft_ack;
-	call->ackr_prev_seq = prev_pkt;
+	call->acks_first_seq = first_soft_ack;
+	call->acks_prev_seq = prev_pkt;
 
 	/* Parse rwind and mtu sizes if provided. */
 	if (buf.info.rxMTU)
@@ -1154,8 +1190,6 @@
  */
 static void rxrpc_reject_packet(struct rxrpc_local *local, struct sk_buff *skb)
 {
-	CHECK_SLAB_OKAY(&local->usage);
-
 	if (rxrpc_get_local_maybe(local)) {
 		skb_queue_tail(&local->reject_queue, skb);
 		rxrpc_queue_local(local);
@@ -1413,7 +1447,7 @@
 		}
 	}
 
-	if (!call || atomic_read(&call->usage) == 0) {
+	if (!call || refcount_read(&call->ref) == 0) {
 		if (rxrpc_to_client(sp) ||
 		    sp->hdr.type != RXRPC_PACKET_TYPE_DATA)
 			goto bad_message;
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/local_object.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/local_object.c
@@ -79,10 +79,10 @@
 
 	local = kzalloc(sizeof(struct rxrpc_local), GFP_KERNEL);
 	if (local) {
-		atomic_set(&local->usage, 1);
+		refcount_set(&local->ref, 1);
 		atomic_set(&local->active_users, 1);
 		local->rxnet = rxnet;
-		INIT_LIST_HEAD(&local->link);
+		INIT_HLIST_NODE(&local->link);
 		INIT_WORK(&local->processor, rxrpc_local_processor);
 		init_rwsem(&local->defrag_sem);
 		skb_queue_head_init(&local->reject_queue);
@@ -117,6 +117,7 @@
 	       local, srx->transport_type, srx->transport.family);
 
 	udp_conf.family = srx->transport.family;
+	udp_conf.use_udp_checksums = true;
 	if (udp_conf.family == AF_INET) {
 		udp_conf.local_ip = srx->transport.sin.sin_addr;
 		udp_conf.local_udp_port = srx->transport.sin.sin_port;
@@ -124,6 +125,8 @@
 	} else {
 		udp_conf.local_ip6 = srx->transport.sin6.sin6_addr;
 		udp_conf.local_udp_port = srx->transport.sin6.sin6_port;
+		udp_conf.use_udp6_tx_checksums = true;
+		udp_conf.use_udp6_rx_checksums = true;
 #endif
 	}
 	ret = udp_sock_create(net, &udp_conf, &local->socket);
@@ -134,6 +137,7 @@
 
 	tuncfg.encap_type = UDP_ENCAP_RXRPC;
 	tuncfg.encap_rcv = rxrpc_input_packet;
+	tuncfg.encap_err_rcv = rxrpc_encap_err_rcv;
 	tuncfg.sk_user_data = local;
 	setup_udp_tunnel_sock(net, local->socket, &tuncfg);
 
@@ -177,7 +181,7 @@
 {
 	struct rxrpc_local *local;
 	struct rxrpc_net *rxnet = rxrpc_net(net);
-	struct list_head *cursor;
+	struct hlist_node *cursor;
 	const char *age;
 	long diff;
 	int ret;
@@ -187,16 +191,12 @@
 
 	mutex_lock(&rxnet->local_mutex);
 
-	for (cursor = rxnet->local_endpoints.next;
-	     cursor != &rxnet->local_endpoints;
-	     cursor = cursor->next) {
-		local = list_entry(cursor, struct rxrpc_local, link);
+	hlist_for_each(cursor, &rxnet->local_endpoints) {
+		local = hlist_entry(cursor, struct rxrpc_local, link);
 
 		diff = rxrpc_local_cmp_key(local, srx);
-		if (diff < 0)
+		if (diff != 0)
 			continue;
-		if (diff > 0)
-			break;
 
 		/* Services aren't allowed to share transport sockets, so
 		 * reject that here.  It is possible that the object is dying -
@@ -208,9 +208,10 @@
 			goto addr_in_use;
 		}
 
-		/* Found a match.  We replace a dying object.  Attempting to
-		 * bind the transport socket may still fail if we're attempting
-		 * to use a local address that the dying object is still using.
+		/* Found a match.  We want to replace a dying object.
+		 * Attempting to bind the transport socket may still fail if
+		 * we're attempting to use a local address that the dying
+		 * object is still using.
 		 */
 		if (!rxrpc_use_local(local))
 			break;
@@ -227,10 +228,12 @@
 	if (ret < 0)
 		goto sock_error;
 
-	if (cursor != &rxnet->local_endpoints)
-		list_replace_init(cursor, &local->link);
-	else
-		list_add_tail(&local->link, cursor);
+	if (cursor) {
+		hlist_replace_rcu(cursor, &local->link);
+		cursor->pprev = NULL;
+	} else {
+		hlist_add_head_rcu(&local->link, &rxnet->local_endpoints);
+	}
 	age = "new";
 
 found:
@@ -263,10 +266,10 @@
 struct rxrpc_local *rxrpc_get_local(struct rxrpc_local *local)
 {
 	const void *here = __builtin_return_address(0);
-	int n;
+	int r;
 
-	n = atomic_inc_return(&local->usage);
-	trace_rxrpc_local(local->debug_id, rxrpc_local_got, n, here);
+	__refcount_inc(&local->ref, &r);
+	trace_rxrpc_local(local->debug_id, rxrpc_local_got, r + 1, here);
 	return local;
 }
 
@@ -276,12 +279,12 @@
 struct rxrpc_local *rxrpc_get_local_maybe(struct rxrpc_local *local)
 {
 	const void *here = __builtin_return_address(0);
+	int r;
 
 	if (local) {
-		int n = atomic_fetch_add_unless(&local->usage, 1, 0);
-		if (n > 0)
+		if (__refcount_inc_not_zero(&local->ref, &r))
 			trace_rxrpc_local(local->debug_id, rxrpc_local_got,
-					  n + 1, here);
+					  r + 1, here);
 		else
 			local = NULL;
 	}
@@ -295,10 +298,10 @@
 {
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id = local->debug_id;
-	int n = atomic_read(&local->usage);
+	int r = refcount_read(&local->ref);
 
 	if (rxrpc_queue_work(&local->processor))
-		trace_rxrpc_local(debug_id, rxrpc_local_queued, n, here);
+		trace_rxrpc_local(debug_id, rxrpc_local_queued, r + 1, here);
 	else
 		rxrpc_put_local(local);
 }
@@ -310,15 +313,16 @@
 {
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id;
-	int n;
+	bool dead;
+	int r;
 
 	if (local) {
 		debug_id = local->debug_id;
 
-		n = atomic_dec_return(&local->usage);
-		trace_rxrpc_local(debug_id, rxrpc_local_put, n, here);
+		dead = __refcount_dec_and_test(&local->ref, &r);
+		trace_rxrpc_local(debug_id, rxrpc_local_put, r, here);
 
-		if (n == 0)
+		if (dead)
 			call_rcu(&local->rcu, rxrpc_local_rcu);
 	}
 }
@@ -371,7 +375,7 @@
 	local->dead = true;
 
 	mutex_lock(&rxnet->local_mutex);
-	list_del_init(&local->link);
+	hlist_del_init_rcu(&local->link);
 	mutex_unlock(&rxnet->local_mutex);
 
 	rxrpc_clean_up_local_conns(local);
@@ -402,8 +406,11 @@
 		container_of(work, struct rxrpc_local, processor);
 	bool again;
 
+	if (local->dead)
+		return;
+
 	trace_rxrpc_local(local->debug_id, rxrpc_local_processing,
-			  atomic_read(&local->usage), NULL);
+			  refcount_read(&local->ref), NULL);
 
 	do {
 		again = false;
@@ -455,11 +462,11 @@
 
 	flush_workqueue(rxrpc_workqueue);
 
-	if (!list_empty(&rxnet->local_endpoints)) {
+	if (!hlist_empty(&rxnet->local_endpoints)) {
 		mutex_lock(&rxnet->local_mutex);
-		list_for_each_entry(local, &rxnet->local_endpoints, link) {
+		hlist_for_each_entry(local, &rxnet->local_endpoints, link) {
 			pr_err("AF_RXRPC: Leaked local %p {%d}\n",
-			       local, atomic_read(&local->usage));
+			       local, refcount_read(&local->ref));
 		}
 		mutex_unlock(&rxnet->local_mutex);
 		BUG();
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/net_ns.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/net_ns.c
@@ -50,7 +50,7 @@
 	rxnet->epoch |= RXRPC_RANDOM_EPOCH;
 
 	INIT_LIST_HEAD(&rxnet->calls);
-	rwlock_init(&rxnet->call_lock);
+	spin_lock_init(&rxnet->call_lock);
 	atomic_set(&rxnet->nr_calls, 1);
 
 	atomic_set(&rxnet->nr_conns, 1);
@@ -72,7 +72,7 @@
 	timer_setup(&rxnet->client_conn_reap_timer,
 		    rxrpc_client_conn_reap_timeout, 0);
 
-	INIT_LIST_HEAD(&rxnet->local_endpoints);
+	INIT_HLIST_HEAD(&rxnet->local_endpoints);
 	mutex_init(&rxnet->local_mutex);
 
 	hash_init(rxnet->peer_hash);
@@ -98,6 +98,9 @@
 	proc_create_net("peers", 0444, rxnet->proc_net,
 			&rxrpc_peer_seq_ops,
 			sizeof(struct seq_net_private));
+	proc_create_net("locals", 0444, rxnet->proc_net,
+			&rxrpc_local_seq_ops,
+			sizeof(struct seq_net_private));
 	return 0;
 
 err_proc:
@@ -115,6 +118,8 @@
 	rxnet->live = false;
 	del_timer_sync(&rxnet->peer_keepalive_timer);
 	cancel_work_sync(&rxnet->peer_keepalive_work);
+	/* Remove the timer again as the worker may have restarted it. */
+	del_timer_sync(&rxnet->peer_keepalive_timer);
 	rxrpc_destroy_all_calls(rxnet);
 	rxrpc_destroy_all_connections(rxnet);
 	rxrpc_destroy_all_peers(rxnet);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/output.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/output.c
@@ -74,22 +74,29 @@
 				 u8 reason)
 {
 	rxrpc_serial_t serial;
+	unsigned int tmp;
 	rxrpc_seq_t hard_ack, top, seq;
 	int ix;
 	u32 mtu, jmax;
 	u8 *ackp = pkt->acks;
 
+	tmp = atomic_xchg(&call->ackr_nr_unacked, 0);
+	tmp |= atomic_xchg(&call->ackr_nr_consumed, 0);
+	if (!tmp && (reason == RXRPC_ACK_DELAY ||
+		     reason == RXRPC_ACK_IDLE))
+		return 0;
+
 	/* Barrier against rxrpc_input_data(). */
-	serial = call->ackr_serial;
+	serial = 0;
 	hard_ack = READ_ONCE(call->rx_hard_ack);
 	top = smp_load_acquire(&call->rx_top);
 	*_hard_ack = hard_ack;
 	*_top = top;
 
-	pkt->ack.bufferSpace	= htons(8);
+	pkt->ack.bufferSpace	= htons(0);
 	pkt->ack.maxSkew	= htons(0);
 	pkt->ack.firstPacket	= htonl(hard_ack + 1);
-	pkt->ack.previousPacket	= htonl(call->ackr_prev_seq);
+	pkt->ack.previousPacket	= htonl(call->ackr_highest_seq);
 	pkt->ack.serial		= htonl(serial);
 	pkt->ack.reason		= reason;
 	pkt->ack.nAcks		= top - hard_ack;
@@ -223,6 +230,10 @@
 	n = rxrpc_fill_out_ack(conn, call, pkt, &hard_ack, &top, reason);
 
 	spin_unlock_bh(&call->lock);
+	if (n == 0) {
+		kfree(pkt);
+		return 0;
+	}
 
 	iov[0].iov_base	= pkt;
 	iov[0].iov_len	= sizeof(pkt->whdr) + sizeof(pkt->ack) + n;
@@ -259,13 +270,6 @@
 					  ntohl(pkt->ack.serial),
 					  false, true,
 					  rxrpc_propose_ack_retry_tx);
-		} else {
-			spin_lock_bh(&call->lock);
-			if (after(hard_ack, call->ackr_consumed))
-				call->ackr_consumed = hard_ack;
-			if (after(top, call->ackr_seen))
-				call->ackr_seen = top;
-			spin_unlock_bh(&call->lock);
 		}
 
 		rxrpc_set_keepalive(call);
@@ -468,7 +472,7 @@
 			if (call->peer->rtt_count > 1) {
 				unsigned long nowj = jiffies, ack_lost_at;
 
-				ack_lost_at = rxrpc_get_rto_backoff(call->peer, retrans);
+				ack_lost_at = rxrpc_get_rto_backoff(call->peer, false);
 				ack_lost_at += nowj;
 				WRITE_ONCE(call->ack_lost_at, ack_lost_at);
 				rxrpc_reduce_call_timer(call, ack_lost_at, nowj,
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/peer_event.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/peer_event.c
@@ -16,22 +16,105 @@
 #include <net/sock.h>
 #include <net/af_rxrpc.h>
 #include <net/ip.h>
+#include <net/icmp.h>
 #include "ar-internal.h"
 
+static void rxrpc_adjust_mtu(struct rxrpc_peer *, unsigned int);
 static void rxrpc_store_error(struct rxrpc_peer *, struct sock_exterr_skb *);
 static void rxrpc_distribute_error(struct rxrpc_peer *, int,
 				   enum rxrpc_call_completion);
 
 /*
- * Find the peer associated with an ICMP packet.
+ * Find the peer associated with an ICMPv4 packet.
  */
 static struct rxrpc_peer *rxrpc_lookup_peer_icmp_rcu(struct rxrpc_local *local,
-						     const struct sk_buff *skb,
+						     struct sk_buff *skb,
+						     unsigned int udp_offset,
+						     unsigned int *info,
 						     struct sockaddr_rxrpc *srx)
 {
-	struct sock_exterr_skb *serr = SKB_EXT_ERR(skb);
+	struct iphdr *ip, *ip0 = ip_hdr(skb);
+	struct icmphdr *icmp = icmp_hdr(skb);
+	struct udphdr *udp = (struct udphdr *)(skb->data + udp_offset);
+
+	_enter("%u,%u,%u", ip0->protocol, icmp->type, icmp->code);
+
+	switch (icmp->type) {
+	case ICMP_DEST_UNREACH:
+		*info = ntohs(icmp->un.frag.mtu);
+		fallthrough;
+	case ICMP_TIME_EXCEEDED:
+	case ICMP_PARAMETERPROB:
+		ip = (struct iphdr *)((void *)icmp + 8);
+		break;
+	default:
+		return NULL;
+	}
 
-	_enter("");
+	memset(srx, 0, sizeof(*srx));
+	srx->transport_type = local->srx.transport_type;
+	srx->transport_len = local->srx.transport_len;
+	srx->transport.family = local->srx.transport.family;
+
+	/* Can we see an ICMP4 packet on an ICMP6 listening socket?  and vice
+	 * versa?
+	 */
+	switch (srx->transport.family) {
+	case AF_INET:
+		srx->transport_len = sizeof(srx->transport.sin);
+		srx->transport.family = AF_INET;
+		srx->transport.sin.sin_port = udp->dest;
+		memcpy(&srx->transport.sin.sin_addr, &ip->daddr,
+		       sizeof(struct in_addr));
+		break;
+
+#ifdef CONFIG_AF_RXRPC_IPV6
+	case AF_INET6:
+		srx->transport_len = sizeof(srx->transport.sin);
+		srx->transport.family = AF_INET;
+		srx->transport.sin.sin_port = udp->dest;
+		memcpy(&srx->transport.sin.sin_addr, &ip->daddr,
+		       sizeof(struct in_addr));
+		break;
+#endif
+
+	default:
+		WARN_ON_ONCE(1);
+		return NULL;
+	}
+
+	_net("ICMP {%pISp}", &srx->transport);
+	return rxrpc_lookup_peer_rcu(local, srx);
+}
+
+#ifdef CONFIG_AF_RXRPC_IPV6
+/*
+ * Find the peer associated with an ICMPv6 packet.
+ */
+static struct rxrpc_peer *rxrpc_lookup_peer_icmp6_rcu(struct rxrpc_local *local,
+						      struct sk_buff *skb,
+						      unsigned int udp_offset,
+						      unsigned int *info,
+						      struct sockaddr_rxrpc *srx)
+{
+	struct icmp6hdr *icmp = icmp6_hdr(skb);
+	struct ipv6hdr *ip, *ip0 = ipv6_hdr(skb);
+	struct udphdr *udp = (struct udphdr *)(skb->data + udp_offset);
+
+	_enter("%u,%u,%u", ip0->nexthdr, icmp->icmp6_type, icmp->icmp6_code);
+
+	switch (icmp->icmp6_type) {
+	case ICMPV6_DEST_UNREACH:
+		*info = ntohl(icmp->icmp6_mtu);
+		fallthrough;
+	case ICMPV6_PKT_TOOBIG:
+	case ICMPV6_TIME_EXCEED:
+	case ICMPV6_PARAMPROB:
+		ip = (struct ipv6hdr *)((void *)icmp + 8);
+		break;
+	default:
+		return NULL;
+	}
 
 	memset(srx, 0, sizeof(*srx));
 	srx->transport_type = local->srx.transport_type;
@@ -43,6 +126,165 @@
 	 */
 	switch (srx->transport.family) {
 	case AF_INET:
+		_net("Rx ICMP6 on v4 sock");
+		srx->transport_len = sizeof(srx->transport.sin);
+		srx->transport.family = AF_INET;
+		srx->transport.sin.sin_port = udp->dest;
+		memcpy(&srx->transport.sin.sin_addr,
+		       &ip->daddr.s6_addr32[3], sizeof(struct in_addr));
+		break;
+	case AF_INET6:
+		_net("Rx ICMP6");
+		srx->transport.sin.sin_port = udp->dest;
+		memcpy(&srx->transport.sin6.sin6_addr, &ip->daddr,
+		       sizeof(struct in6_addr));
+		break;
+	default:
+		WARN_ON_ONCE(1);
+		return NULL;
+	}
+
+	_net("ICMP {%pISp}", &srx->transport);
+	return rxrpc_lookup_peer_rcu(local, srx);
+}
+#endif /* CONFIG_AF_RXRPC_IPV6 */
+
+/*
+ * Handle an error received on the local endpoint as a tunnel.
+ */
+void rxrpc_encap_err_rcv(struct sock *sk, struct sk_buff *skb,
+			 unsigned int udp_offset)
+{
+	struct sock_extended_err ee;
+	struct sockaddr_rxrpc srx;
+	struct rxrpc_local *local;
+	struct rxrpc_peer *peer;
+	unsigned int info = 0;
+	int err;
+	u8 version = ip_hdr(skb)->version;
+	u8 type = icmp_hdr(skb)->type;
+	u8 code = icmp_hdr(skb)->code;
+
+	rcu_read_lock();
+	local = rcu_dereference_sk_user_data(sk);
+	if (unlikely(!local)) {
+		rcu_read_unlock();
+		return;
+	}
+
+	rxrpc_new_skb(skb, rxrpc_skb_received);
+
+	switch (ip_hdr(skb)->version) {
+	case IPVERSION:
+		peer = rxrpc_lookup_peer_icmp_rcu(local, skb, udp_offset,
+						  &info, &srx);
+		break;
+#ifdef CONFIG_AF_RXRPC_IPV6
+	case 6:
+		peer = rxrpc_lookup_peer_icmp6_rcu(local, skb, udp_offset,
+						   &info, &srx);
+		break;
+#endif
+	default:
+		rcu_read_unlock();
+		return;
+	}
+
+	if (peer && !rxrpc_get_peer_maybe(peer))
+		peer = NULL;
+	if (!peer) {
+		rcu_read_unlock();
+		return;
+	}
+
+	memset(&ee, 0, sizeof(ee));
+
+	switch (version) {
+	case IPVERSION:
+		switch (type) {
+		case ICMP_DEST_UNREACH:
+			switch (code) {
+			case ICMP_FRAG_NEEDED:
+				rxrpc_adjust_mtu(peer, info);
+				rcu_read_unlock();
+				rxrpc_put_peer(peer);
+				return;
+			default:
+				break;
+			}
+
+			err = EHOSTUNREACH;
+			if (code <= NR_ICMP_UNREACH) {
+				/* Might want to do something different with
+				 * non-fatal errors
+				 */
+				//harderr = icmp_err_convert[code].fatal;
+				err = icmp_err_convert[code].errno;
+			}
+			break;
+
+		case ICMP_TIME_EXCEEDED:
+			err = EHOSTUNREACH;
+			break;
+		default:
+			err = EPROTO;
+			break;
+		}
+
+		ee.ee_origin = SO_EE_ORIGIN_ICMP;
+		ee.ee_type = type;
+		ee.ee_code = code;
+		ee.ee_errno = err;
+		break;
+
+#ifdef CONFIG_AF_RXRPC_IPV6
+	case 6:
+		switch (type) {
+		case ICMPV6_PKT_TOOBIG:
+			rxrpc_adjust_mtu(peer, info);
+			rcu_read_unlock();
+			rxrpc_put_peer(peer);
+			return;
+		}
+
+		icmpv6_err_convert(type, code, &err);
+
+		if (err == EACCES)
+			err = EHOSTUNREACH;
+
+		ee.ee_origin = SO_EE_ORIGIN_ICMP6;
+		ee.ee_type = type;
+		ee.ee_code = code;
+		ee.ee_errno = err;
+		break;
+#endif
+	}
+
+	trace_rxrpc_rx_icmp(peer, &ee, &srx);
+
+	rxrpc_distribute_error(peer, err, RXRPC_CALL_NETWORK_ERROR);
+	rcu_read_unlock();
+	rxrpc_put_peer(peer);
+}
+
+/*
+ * Find the peer associated with a local error.
+ */
+static struct rxrpc_peer *rxrpc_lookup_peer_local_rcu(struct rxrpc_local *local,
+						      const struct sk_buff *skb,
+						      struct sockaddr_rxrpc *srx)
+{
+	struct sock_exterr_skb *serr = SKB_EXT_ERR(skb);
+
+	_enter("");
+
+	memset(srx, 0, sizeof(*srx));
+	srx->transport_type = local->srx.transport_type;
+	srx->transport_len = local->srx.transport_len;
+	srx->transport.family = local->srx.transport.family;
+
+	switch (srx->transport.family) {
+	case AF_INET:
 		srx->transport_len = sizeof(srx->transport.sin);
 		srx->transport.family = AF_INET;
 		srx->transport.sin.sin_port = serr->port;
@@ -104,10 +346,8 @@
 /*
  * Handle an MTU/fragmentation problem.
  */
-static void rxrpc_adjust_mtu(struct rxrpc_peer *peer, struct sock_exterr_skb *serr)
+static void rxrpc_adjust_mtu(struct rxrpc_peer *peer, unsigned int mtu)
 {
-	u32 mtu = serr->ee.ee_info;
-
 	_net("Rx ICMP Fragmentation Needed (%d)", mtu);
 
 	/* wind down the local interface MTU */
@@ -148,7 +388,7 @@
 	struct sock_exterr_skb *serr;
 	struct sockaddr_rxrpc srx;
 	struct rxrpc_local *local;
-	struct rxrpc_peer *peer;
+	struct rxrpc_peer *peer = NULL;
 	struct sk_buff *skb;
 
 	rcu_read_lock();
@@ -172,41 +412,20 @@
 	}
 	rxrpc_new_skb(skb, rxrpc_skb_received);
 	serr = SKB_EXT_ERR(skb);
-	if (!skb->len && serr->ee.ee_origin == SO_EE_ORIGIN_TIMESTAMPING) {
-		_leave("UDP empty message");
-		rcu_read_unlock();
-		rxrpc_free_skb(skb, rxrpc_skb_freed);
-		return;
-	}
 
-	peer = rxrpc_lookup_peer_icmp_rcu(local, skb, &srx);
-	if (peer && !rxrpc_get_peer_maybe(peer))
-		peer = NULL;
-	if (!peer) {
-		rcu_read_unlock();
-		rxrpc_free_skb(skb, rxrpc_skb_freed);
-		_leave(" [no peer]");
-		return;
-	}
-
-	trace_rxrpc_rx_icmp(peer, &serr->ee, &srx);
-
-	if ((serr->ee.ee_origin == SO_EE_ORIGIN_ICMP &&
-	     serr->ee.ee_type == ICMP_DEST_UNREACH &&
-	     serr->ee.ee_code == ICMP_FRAG_NEEDED)) {
-		rxrpc_adjust_mtu(peer, serr);
-		rcu_read_unlock();
-		rxrpc_free_skb(skb, rxrpc_skb_freed);
-		rxrpc_put_peer(peer);
-		_leave(" [MTU update]");
-		return;
+	if (serr->ee.ee_origin == SO_EE_ORIGIN_LOCAL) {
+		peer = rxrpc_lookup_peer_local_rcu(local, skb, &srx);
+		if (peer && !rxrpc_get_peer_maybe(peer))
+			peer = NULL;
+		if (peer) {
+			trace_rxrpc_rx_icmp(peer, &serr->ee, &srx);
+			rxrpc_store_error(peer, serr);
+		}
 	}
 
-	rxrpc_store_error(peer, serr);
 	rcu_read_unlock();
 	rxrpc_free_skb(skb, rxrpc_skb_freed);
 	rxrpc_put_peer(peer);
-
 	_leave("");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/peer_object.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/peer_object.c
@@ -121,7 +121,7 @@
 
 	hash_for_each_possible_rcu(rxnet->peer_hash, peer, hash_link, hash_key) {
 		if (rxrpc_peer_cmp_key(peer, local, srx, hash_key) == 0 &&
-		    atomic_read(&peer->usage) > 0)
+		    refcount_read(&peer->ref) > 0)
 			return peer;
 	}
 
@@ -140,7 +140,7 @@
 	peer = __rxrpc_lookup_peer_rcu(local, srx, hash_key);
 	if (peer) {
 		_net("PEER %d {%pISp}", peer->debug_id, &peer->srx.transport);
-		_leave(" = %p {u=%d}", peer, atomic_read(&peer->usage));
+		_leave(" = %p {u=%d}", peer, refcount_read(&peer->ref));
 	}
 	return peer;
 }
@@ -216,7 +216,7 @@
 
 	peer = kzalloc(sizeof(struct rxrpc_peer), gfp);
 	if (peer) {
-		atomic_set(&peer->usage, 1);
+		refcount_set(&peer->ref, 1);
 		peer->local = rxrpc_get_local(local);
 		INIT_HLIST_HEAD(&peer->error_targets);
 		peer->service_conns = RB_ROOT;
@@ -299,6 +299,12 @@
 	return peer;
 }
 
+static void rxrpc_free_peer(struct rxrpc_peer *peer)
+{
+	rxrpc_put_local(peer->local);
+	kfree_rcu(peer, rcu);
+}
+
 /*
  * Set up a new incoming peer.  There shouldn't be any other matching peers
  * since we've already done a search in the list from the non-reentrant context
@@ -365,14 +371,14 @@
 		spin_unlock_bh(&rxnet->peer_hash_lock);
 
 		if (peer)
-			kfree(candidate);
+			rxrpc_free_peer(candidate);
 		else
 			peer = candidate;
 	}
 
 	_net("PEER %d {%pISp}", peer->debug_id, &peer->srx.transport);
 
-	_leave(" = %p {u=%d}", peer, atomic_read(&peer->usage));
+	_leave(" = %p {u=%d}", peer, refcount_read(&peer->ref));
 	return peer;
 }
 
@@ -382,10 +388,10 @@
 struct rxrpc_peer *rxrpc_get_peer(struct rxrpc_peer *peer)
 {
 	const void *here = __builtin_return_address(0);
-	int n;
+	int r;
 
-	n = atomic_inc_return(&peer->usage);
-	trace_rxrpc_peer(peer->debug_id, rxrpc_peer_got, n, here);
+	__refcount_inc(&peer->ref, &r);
+	trace_rxrpc_peer(peer->debug_id, rxrpc_peer_got, r + 1, here);
 	return peer;
 }
 
@@ -395,11 +401,11 @@
 struct rxrpc_peer *rxrpc_get_peer_maybe(struct rxrpc_peer *peer)
 {
 	const void *here = __builtin_return_address(0);
+	int r;
 
 	if (peer) {
-		int n = atomic_fetch_add_unless(&peer->usage, 1, 0);
-		if (n > 0)
-			trace_rxrpc_peer(peer->debug_id, rxrpc_peer_got, n + 1, here);
+		if (__refcount_inc_not_zero(&peer->ref, &r))
+			trace_rxrpc_peer(peer->debug_id, rxrpc_peer_got, r + 1, here);
 		else
 			peer = NULL;
 	}
@@ -420,8 +426,7 @@
 	list_del_init(&peer->keepalive_link);
 	spin_unlock_bh(&rxnet->peer_hash_lock);
 
-	rxrpc_put_local(peer->local);
-	kfree_rcu(peer, rcu);
+	rxrpc_free_peer(peer);
 }
 
 /*
@@ -431,13 +436,14 @@
 {
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id;
-	int n;
+	bool dead;
+	int r;
 
 	if (peer) {
 		debug_id = peer->debug_id;
-		n = atomic_dec_return(&peer->usage);
-		trace_rxrpc_peer(debug_id, rxrpc_peer_put, n, here);
-		if (n == 0)
+		dead = __refcount_dec_and_test(&peer->ref, &r);
+		trace_rxrpc_peer(debug_id, rxrpc_peer_put, r - 1, here);
+		if (dead)
 			__rxrpc_put_peer(peer);
 	}
 }
@@ -450,15 +456,15 @@
 {
 	const void *here = __builtin_return_address(0);
 	unsigned int debug_id = peer->debug_id;
-	int n;
+	bool dead;
+	int r;
 
-	n = atomic_dec_return(&peer->usage);
-	trace_rxrpc_peer(debug_id, rxrpc_peer_put, n, here);
-	if (n == 0) {
+	dead = __refcount_dec_and_test(&peer->ref, &r);
+	trace_rxrpc_peer(debug_id, rxrpc_peer_put, r - 1, here);
+	if (dead) {
 		hash_del_rcu(&peer->hash_link);
 		list_del_init(&peer->keepalive_link);
-		rxrpc_put_local(peer->local);
-		kfree_rcu(peer, rcu);
+		rxrpc_free_peer(peer);
 	}
 }
 
@@ -477,7 +483,7 @@
 		hlist_for_each_entry(peer, &rxnet->peer_hash[i], hash_link) {
 			pr_err("Leaked peer %u {%u} %pISp\n",
 			       peer->debug_id,
-			       atomic_read(&peer->usage),
+			       refcount_read(&peer->ref),
 			       &peer->srx.transport);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/proc.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/proc.c
@@ -26,29 +26,23 @@
  */
 static void *rxrpc_call_seq_start(struct seq_file *seq, loff_t *_pos)
 	__acquires(rcu)
-	__acquires(rxnet->call_lock)
 {
 	struct rxrpc_net *rxnet = rxrpc_net(seq_file_net(seq));
 
 	rcu_read_lock();
-	read_lock(&rxnet->call_lock);
-	return seq_list_start_head(&rxnet->calls, *_pos);
+	return seq_list_start_head_rcu(&rxnet->calls, *_pos);
 }
 
 static void *rxrpc_call_seq_next(struct seq_file *seq, void *v, loff_t *pos)
 {
 	struct rxrpc_net *rxnet = rxrpc_net(seq_file_net(seq));
 
-	return seq_list_next(v, &rxnet->calls, pos);
+	return seq_list_next_rcu(v, &rxnet->calls, pos);
 }
 
 static void rxrpc_call_seq_stop(struct seq_file *seq, void *v)
-	__releases(rxnet->call_lock)
 	__releases(rcu)
 {
-	struct rxrpc_net *rxnet = rxrpc_net(seq_file_net(seq));
-
-	read_unlock(&rxnet->call_lock);
 	rcu_read_unlock();
 }
 
@@ -107,7 +101,7 @@
 		   call->cid,
 		   call->call_id,
 		   rxrpc_is_service_call(call) ? "Svc" : "Clt",
-		   atomic_read(&call->usage),
+		   refcount_read(&call->ref),
 		   rxrpc_call_states[call->state],
 		   call->abort_code,
 		   call->debug_id,
@@ -189,7 +183,7 @@
 		   conn->service_id,
 		   conn->proto.cid,
 		   rxrpc_conn_is_service(conn) ? "Svc" : "Clt",
-		   atomic_read(&conn->usage),
+		   refcount_read(&conn->ref),
 		   rxrpc_conn_states[conn->state],
 		   key_serial(conn->params.key),
 		   atomic_read(&conn->serial),
@@ -239,7 +233,7 @@
 		   " %3u %5u %6llus %8u %8u\n",
 		   lbuff,
 		   rbuff,
-		   atomic_read(&peer->usage),
+		   refcount_read(&peer->ref),
 		   peer->cong_cwnd,
 		   peer->mtu,
 		   now - peer->last_tx_at,
@@ -334,3 +328,72 @@
 	.stop   = rxrpc_peer_seq_stop,
 	.show   = rxrpc_peer_seq_show,
 };
+
+/*
+ * Generate a list of extant virtual local endpoints in /proc/net/rxrpc/locals
+ */
+static int rxrpc_local_seq_show(struct seq_file *seq, void *v)
+{
+	struct rxrpc_local *local;
+	char lbuff[50];
+
+	if (v == SEQ_START_TOKEN) {
+		seq_puts(seq,
+			 "Proto Local                                          "
+			 " Use Act\n");
+		return 0;
+	}
+
+	local = hlist_entry(v, struct rxrpc_local, link);
+
+	sprintf(lbuff, "%pISpc", &local->srx.transport);
+
+	seq_printf(seq,
+		   "UDP   %-47.47s %3u %3u\n",
+		   lbuff,
+		   refcount_read(&local->ref),
+		   atomic_read(&local->active_users));
+
+	return 0;
+}
+
+static void *rxrpc_local_seq_start(struct seq_file *seq, loff_t *_pos)
+	__acquires(rcu)
+{
+	struct rxrpc_net *rxnet = rxrpc_net(seq_file_net(seq));
+	unsigned int n;
+
+	rcu_read_lock();
+
+	if (*_pos >= UINT_MAX)
+		return NULL;
+
+	n = *_pos;
+	if (n == 0)
+		return SEQ_START_TOKEN;
+
+	return seq_hlist_start_rcu(&rxnet->local_endpoints, n - 1);
+}
+
+static void *rxrpc_local_seq_next(struct seq_file *seq, void *v, loff_t *_pos)
+{
+	struct rxrpc_net *rxnet = rxrpc_net(seq_file_net(seq));
+
+	if (*_pos >= UINT_MAX)
+		return NULL;
+
+	return seq_hlist_next_rcu(v, &rxnet->local_endpoints, _pos);
+}
+
+static void rxrpc_local_seq_stop(struct seq_file *seq, void *v)
+	__releases(rcu)
+{
+	rcu_read_unlock();
+}
+
+const struct seq_operations rxrpc_local_seq_ops = {
+	.start  = rxrpc_local_seq_start,
+	.next   = rxrpc_local_seq_next,
+	.stop   = rxrpc_local_seq_stop,
+	.show   = rxrpc_local_seq_show,
+};
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/recvmsg.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/recvmsg.c
@@ -260,11 +260,9 @@
 		rxrpc_end_rx_phase(call, serial);
 	} else {
 		/* Check to see if there's an ACK that needs sending. */
-		if (after_eq(hard_ack, call->ackr_consumed + 2) ||
-		    after_eq(top, call->ackr_seen + 2) ||
-		    (hard_ack == top && after(hard_ack, call->ackr_consumed)))
-			rxrpc_propose_ACK(call, RXRPC_ACK_DELAY, serial,
-					  true, true,
+		if (atomic_inc_return(&call->ackr_nr_consumed) > 2)
+			rxrpc_propose_ACK(call, RXRPC_ACK_IDLE, serial,
+					  true, false,
 					  rxrpc_propose_ack_rotate_rx);
 		if (call->ackr_reason && call->ackr_reason != RXRPC_ACK_DELAY)
 			rxrpc_send_ack_packet(call, false, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/rtt.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/rtt.c
@@ -22,7 +22,7 @@
 
 static u32 __rxrpc_set_rto(const struct rxrpc_peer *peer)
 {
-	return _usecs_to_jiffies((peer->srtt_us >> 3) + peer->rttvar_us);
+	return usecs_to_jiffies((peer->srtt_us >> 3) + peer->rttvar_us);
 }
 
 static u32 rxrpc_bound_rto(u32 rto)
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/rxkad.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/rxkad.c
@@ -540,7 +540,7 @@
 	 * directly into the target buffer.
 	 */
 	sg = _sg;
-	nsg = skb_shinfo(skb)->nr_frags;
+	nsg = skb_shinfo(skb)->nr_frags + 1;
 	if (nsg <= 4) {
 		nsg = 4;
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/sendmsg.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/sendmsg.c
@@ -51,10 +51,7 @@
 			return sock_intr_errno(*timeo);
 
 		trace_rxrpc_transmit(call, rxrpc_transmit_wait);
-		mutex_unlock(&call->user_mutex);
 		*timeo = schedule_timeout(*timeo);
-		if (mutex_lock_interruptible(&call->user_mutex) < 0)
-			return sock_intr_errno(*timeo);
 	}
 }
 
@@ -290,37 +287,48 @@
 static int rxrpc_send_data(struct rxrpc_sock *rx,
 			   struct rxrpc_call *call,
 			   struct msghdr *msg, size_t len,
-			   rxrpc_notify_end_tx_t notify_end_tx)
+			   rxrpc_notify_end_tx_t notify_end_tx,
+			   bool *_dropped_lock)
 {
 	struct rxrpc_skb_priv *sp;
 	struct sk_buff *skb;
 	struct sock *sk = &rx->sk;
+	enum rxrpc_call_state state;
 	long timeo;
-	bool more;
-	int ret, copied;
+	bool more = msg->msg_flags & MSG_MORE;
+	int ret, copied = 0;
 
 	timeo = sock_sndtimeo(sk, msg->msg_flags & MSG_DONTWAIT);
 
 	/* this should be in poll */
 	sk_clear_bit(SOCKWQ_ASYNC_NOSPACE, sk);
 
+reload:
+	ret = -EPIPE;
 	if (sk->sk_shutdown & SEND_SHUTDOWN)
-		return -EPIPE;
-
-	more = msg->msg_flags & MSG_MORE;
+		goto maybe_error;
+	state = READ_ONCE(call->state);
+	ret = -ESHUTDOWN;
+	if (state >= RXRPC_CALL_COMPLETE)
+		goto maybe_error;
+	ret = -EPROTO;
+	if (state != RXRPC_CALL_CLIENT_SEND_REQUEST &&
+	    state != RXRPC_CALL_SERVER_ACK_REQUEST &&
+	    state != RXRPC_CALL_SERVER_SEND_REPLY)
+		goto maybe_error;
 
+	ret = -EMSGSIZE;
 	if (call->tx_total_len != -1) {
-		if (len > call->tx_total_len)
-			return -EMSGSIZE;
-		if (!more && len != call->tx_total_len)
-			return -EMSGSIZE;
+		if (len - copied > call->tx_total_len)
+			goto maybe_error;
+		if (!more && len - copied != call->tx_total_len)
+			goto maybe_error;
 	}
 
 	skb = call->tx_pending;
 	call->tx_pending = NULL;
 	rxrpc_see_skb(skb, rxrpc_skb_seen);
 
-	copied = 0;
 	do {
 		/* Check to see if there's a ping ACK to reply to. */
 		if (call->ackr_reason == RXRPC_ACK_PING_RESPONSE)
@@ -331,16 +339,8 @@
 
 			_debug("alloc");
 
-			if (!rxrpc_check_tx_space(call, NULL)) {
-				ret = -EAGAIN;
-				if (msg->msg_flags & MSG_DONTWAIT)
-					goto maybe_error;
-				ret = rxrpc_wait_for_tx_window(rx, call,
-							       &timeo,
-							       msg->msg_flags & MSG_WAITALL);
-				if (ret < 0)
-					goto maybe_error;
-			}
+			if (!rxrpc_check_tx_space(call, NULL))
+				goto wait_for_space;
 
 			/* Work out the maximum size of a packet.  Assume that
 			 * the security header is going to be in the padded
@@ -444,6 +444,12 @@
 
 success:
 	ret = copied;
+	if (READ_ONCE(call->state) == RXRPC_CALL_COMPLETE) {
+		read_lock_bh(&call->state_lock);
+		if (call->error < 0)
+			ret = call->error;
+		read_unlock_bh(&call->state_lock);
+	}
 out:
 	call->tx_pending = skb;
 	_leave(" = %d", ret);
@@ -462,6 +468,27 @@
 efault:
 	ret = -EFAULT;
 	goto out;
+
+wait_for_space:
+	ret = -EAGAIN;
+	if (msg->msg_flags & MSG_DONTWAIT)
+		goto maybe_error;
+	mutex_unlock(&call->user_mutex);
+	*_dropped_lock = true;
+	ret = rxrpc_wait_for_tx_window(rx, call, &timeo,
+				       msg->msg_flags & MSG_WAITALL);
+	if (ret < 0)
+		goto maybe_error;
+	if (call->interruptibility == RXRPC_INTERRUPTIBLE) {
+		if (mutex_lock_interruptible(&call->user_mutex) < 0) {
+			ret = sock_intr_errno(timeo);
+			goto maybe_error;
+		}
+	} else {
+		mutex_lock(&call->user_mutex);
+	}
+	*_dropped_lock = false;
+	goto reload;
 }
 
 /*
@@ -623,6 +650,7 @@
 	enum rxrpc_call_state state;
 	struct rxrpc_call *call;
 	unsigned long now, j;
+	bool dropped_lock = false;
 	int ret;
 
 	struct rxrpc_send_params p = {
@@ -688,7 +716,7 @@
 			if (call->tx_total_len != -1 ||
 			    call->tx_pending ||
 			    call->tx_top != 0)
-				goto error_put;
+				goto out_put_unlock;
 			call->tx_total_len = p.call.tx_total_len;
 		}
 	}
@@ -708,7 +736,7 @@
 		fallthrough;
 	case 1:
 		if (p.call.timeouts.hard > 0) {
-			j = msecs_to_jiffies(p.call.timeouts.hard);
+			j = p.call.timeouts.hard * HZ;
 			now = jiffies;
 			j += now;
 			WRITE_ONCE(call->expect_term_by, j);
@@ -731,21 +759,13 @@
 			ret = rxrpc_send_abort_packet(call);
 	} else if (p.command != RXRPC_CMD_SEND_DATA) {
 		ret = -EINVAL;
-	} else if (rxrpc_is_client_call(call) &&
-		   state != RXRPC_CALL_CLIENT_SEND_REQUEST) {
-		/* request phase complete for this client call */
-		ret = -EPROTO;
-	} else if (rxrpc_is_service_call(call) &&
-		   state != RXRPC_CALL_SERVER_ACK_REQUEST &&
-		   state != RXRPC_CALL_SERVER_SEND_REPLY) {
-		/* Reply phase not begun or not complete for service call. */
-		ret = -EPROTO;
 	} else {
-		ret = rxrpc_send_data(rx, call, msg, len, NULL);
+		ret = rxrpc_send_data(rx, call, msg, len, NULL, &dropped_lock);
 	}
 
 out_put_unlock:
-	mutex_unlock(&call->user_mutex);
+	if (!dropped_lock)
+		mutex_unlock(&call->user_mutex);
 error_put:
 	rxrpc_put_call(call, rxrpc_call_put);
 	_leave(" = %d", ret);
@@ -773,6 +793,7 @@
 			   struct msghdr *msg, size_t len,
 			   rxrpc_notify_end_tx_t notify_end_tx)
 {
+	bool dropped_lock = false;
 	int ret;
 
 	_enter("{%d,%s},", call->debug_id, rxrpc_call_states[call->state]);
@@ -790,7 +811,7 @@
 	case RXRPC_CALL_SERVER_ACK_REQUEST:
 	case RXRPC_CALL_SERVER_SEND_REPLY:
 		ret = rxrpc_send_data(rxrpc_sk(sock->sk), call, msg, len,
-				      notify_end_tx);
+				      notify_end_tx, &dropped_lock);
 		break;
 	case RXRPC_CALL_COMPLETE:
 		read_lock_bh(&call->state_lock);
@@ -804,7 +825,8 @@
 		break;
 	}
 
-	mutex_unlock(&call->user_mutex);
+	if (!dropped_lock)
+		mutex_unlock(&call->user_mutex);
 	_leave(" = %d", ret);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/server_key.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/server_key.c
@@ -84,6 +84,9 @@
 
 	prep->payload.data[1] = (struct rxrpc_security *)sec;
 
+	if (!sec->preparse_server_key)
+		return -EINVAL;
+
 	return sec->preparse_server_key(prep);
 }
 
@@ -91,7 +94,7 @@
 {
 	const struct rxrpc_security *sec = prep->payload.data[1];
 
-	if (sec)
+	if (sec && sec->free_preparse_server_key)
 		sec->free_preparse_server_key(prep);
 }
 
@@ -99,7 +102,7 @@
 {
 	const struct rxrpc_security *sec = key->payload.data[1];
 
-	if (sec)
+	if (sec && sec->destroy_server_key)
 		sec->destroy_server_key(key);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/skbuff.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/skbuff.c
@@ -71,7 +71,6 @@
 	const void *here = __builtin_return_address(0);
 	if (skb) {
 		int n;
-		CHECK_SLAB_OKAY(&skb->users);
 		n = atomic_dec_return(select_skb_count(skb));
 		trace_rxrpc_skb(skb, op, refcount_read(&skb->users), n,
 				rxrpc_skb(skb)->rx_flags, here);
--- linux-xilinx-zynqmp-5.15.0.orig/net/rxrpc/sysctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/rxrpc/sysctl.c
@@ -12,7 +12,7 @@
 
 static struct ctl_table_header *rxrpc_sysctl_reg_table;
 static const unsigned int four = 4;
-static const unsigned int thirtytwo = 32;
+static const unsigned int max_backlog = RXRPC_BACKLOG_MAX - 1;
 static const unsigned int n_65535 = 65535;
 static const unsigned int n_max_acks = RXRPC_RXTX_BUFF_SIZE - 1;
 static const unsigned long one_jiffy = 1;
@@ -89,7 +89,7 @@
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= (void *)&four,
-		.extra2		= (void *)&thirtytwo,
+		.extra2		= (void *)&max_backlog,
 	},
 	{
 		.procname	= "rx_window_size",
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/net/sched/Kconfig
@@ -45,23 +45,6 @@
 
 comment "Queueing/Scheduling"
 
-config NET_SCH_CBQ
-	tristate "Class Based Queueing (CBQ)"
-	help
-	  Say Y here if you want to use the Class-Based Queueing (CBQ) packet
-	  scheduling algorithm. This algorithm classifies the waiting packets
-	  into a tree-like hierarchy of classes; the leaves of this tree are
-	  in turn scheduled by separate algorithms.
-
-	  See the top of <file:net/sched/sch_cbq.c> for more details.
-
-	  CBQ is a commonly used scheduler, so if you're unsure, you should
-	  say Y here. Then say Y to all the queueing algorithms below that you
-	  want to use as leaf disciplines.
-
-	  To compile this code as a module, choose M here: the
-	  module will be called sch_cbq.
-
 config NET_SCH_HTB
 	tristate "Hierarchical Token Bucket (HTB)"
 	help
@@ -85,20 +68,6 @@
 	  To compile this code as a module, choose M here: the
 	  module will be called sch_hfsc.
 
-config NET_SCH_ATM
-	tristate "ATM Virtual Circuits (ATM)"
-	depends on ATM
-	help
-	  Say Y here if you want to use the ATM pseudo-scheduler.  This
-	  provides a framework for invoking classifiers, which in turn
-	  select classes of this queuing discipline.  Each class maps
-	  the flow(s) it is handling to a given virtual circuit.
-
-	  See the top of <file:net/sched/sch_atm.c> for more details.
-
-	  To compile this code as a module, choose M here: the
-	  module will be called sch_atm.
-
 config NET_SCH_PRIO
 	tristate "Multi Band Priority Queueing (PRIO)"
 	help
@@ -217,17 +186,6 @@
 	  To compile this code as a module, choose M here: the
 	  module will be called sch_gred.
 
-config NET_SCH_DSMARK
-	tristate "Differentiated Services marker (DSMARK)"
-	help
-	  Say Y if you want to schedule packets according to the
-	  Differentiated Services architecture proposed in RFC 2475.
-	  Technical information on this method, with pointers to associated
-	  RFCs, is available at <http://www.gta.ufrj.br/diffserv/>.
-
-	  To compile this code as a module, choose M here: the
-	  module will be called sch_dsmark.
-
 config NET_SCH_NETEM
 	tristate "Network emulator (NETEM)"
 	help
@@ -503,17 +461,6 @@
 	  To compile this code as a module, choose M here: the
 	  module will be called cls_basic.
 
-config NET_CLS_TCINDEX
-	tristate "Traffic-Control Index (TCINDEX)"
-	select NET_CLS
-	help
-	  Say Y here if you want to be able to classify packets based on
-	  traffic control indices. You will want this feature if you want
-	  to implement Differentiated Services together with DSMARK.
-
-	  To compile this code as a module, choose M here: the
-	  module will be called cls_tcindex.
-
 config NET_CLS_ROUTE4
 	tristate "Routing decision (ROUTE)"
 	depends on INET
@@ -559,34 +506,6 @@
 	help
 	  Say Y here to be able to use netfilter marks as u32 key.
 
-config NET_CLS_RSVP
-	tristate "IPv4 Resource Reservation Protocol (RSVP)"
-	select NET_CLS
-	help
-	  The Resource Reservation Protocol (RSVP) permits end systems to
-	  request a minimum and maximum data flow rate for a connection; this
-	  is important for real time data such as streaming sound or video.
-
-	  Say Y here if you want to be able to classify outgoing packets based
-	  on their RSVP requests.
-
-	  To compile this code as a module, choose M here: the
-	  module will be called cls_rsvp.
-
-config NET_CLS_RSVP6
-	tristate "IPv6 Resource Reservation Protocol (RSVP6)"
-	select NET_CLS
-	help
-	  The Resource Reservation Protocol (RSVP) permits end systems to
-	  request a minimum and maximum data flow rate for a connection; this
-	  is important for real time data such as streaming sound or video.
-
-	  Say Y here if you want to be able to classify outgoing packets based
-	  on their RSVP requests and you are using the IPv6 protocol.
-
-	  To compile this code as a module, choose M here: the
-	  module will be called cls_rsvp6.
-
 config NET_CLS_FLOW
 	tristate "Flow classifier"
 	select NET_CLS
@@ -976,7 +895,7 @@
 
 config NET_ACT_CT
 	tristate "connection tracking tc action"
-	depends on NET_CLS_ACT && NF_CONNTRACK && NF_NAT && NF_FLOW_TABLE
+	depends on NET_CLS_ACT && NF_CONNTRACK && (!NF_NAT || NF_NAT) && NF_FLOW_TABLE
 	help
 	  Say Y here to allow sending the packets to conntrack module.
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/sched/Makefile
@@ -33,20 +33,17 @@
 obj-$(CONFIG_NET_ACT_CT)	+= act_ct.o
 obj-$(CONFIG_NET_ACT_GATE)	+= act_gate.o
 obj-$(CONFIG_NET_SCH_FIFO)	+= sch_fifo.o
-obj-$(CONFIG_NET_SCH_CBQ)	+= sch_cbq.o
 obj-$(CONFIG_NET_SCH_HTB)	+= sch_htb.o
 obj-$(CONFIG_NET_SCH_HFSC)	+= sch_hfsc.o
 obj-$(CONFIG_NET_SCH_RED)	+= sch_red.o
 obj-$(CONFIG_NET_SCH_GRED)	+= sch_gred.o
 obj-$(CONFIG_NET_SCH_INGRESS)	+= sch_ingress.o
-obj-$(CONFIG_NET_SCH_DSMARK)	+= sch_dsmark.o
 obj-$(CONFIG_NET_SCH_SFB)	+= sch_sfb.o
 obj-$(CONFIG_NET_SCH_SFQ)	+= sch_sfq.o
 obj-$(CONFIG_NET_SCH_TBF)	+= sch_tbf.o
 obj-$(CONFIG_NET_SCH_TEQL)	+= sch_teql.o
 obj-$(CONFIG_NET_SCH_PRIO)	+= sch_prio.o
 obj-$(CONFIG_NET_SCH_MULTIQ)	+= sch_multiq.o
-obj-$(CONFIG_NET_SCH_ATM)	+= sch_atm.o
 obj-$(CONFIG_NET_SCH_NETEM)	+= sch_netem.o
 obj-$(CONFIG_NET_SCH_DRR)	+= sch_drr.o
 obj-$(CONFIG_NET_SCH_PLUG)	+= sch_plug.o
@@ -69,9 +66,6 @@
 obj-$(CONFIG_NET_CLS_U32)	+= cls_u32.o
 obj-$(CONFIG_NET_CLS_ROUTE4)	+= cls_route.o
 obj-$(CONFIG_NET_CLS_FW)	+= cls_fw.o
-obj-$(CONFIG_NET_CLS_RSVP)	+= cls_rsvp.o
-obj-$(CONFIG_NET_CLS_TCINDEX)	+= cls_tcindex.o
-obj-$(CONFIG_NET_CLS_RSVP6)	+= cls_rsvp6.o
 obj-$(CONFIG_NET_CLS_BASIC)	+= cls_basic.o
 obj-$(CONFIG_NET_CLS_FLOW)	+= cls_flow.o
 obj-$(CONFIG_NET_CLS_CGROUP)	+= cls_cgroup.o
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_api.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_api.c
@@ -350,7 +350,8 @@
 }
 
 static int tcf_del_walker(struct tcf_idrinfo *idrinfo, struct sk_buff *skb,
-			  const struct tc_action_ops *ops)
+			  const struct tc_action_ops *ops,
+			  struct netlink_ext_ack *extack)
 {
 	struct nlattr *nest;
 	int n_i = 0;
@@ -366,20 +367,25 @@
 	if (nla_put_string(skb, TCA_KIND, ops->kind))
 		goto nla_put_failure;
 
+	ret = 0;
 	mutex_lock(&idrinfo->lock);
 	idr_for_each_entry_ul(idr, p, tmp, id) {
 		if (IS_ERR(p))
 			continue;
 		ret = tcf_idr_release_unsafe(p);
-		if (ret == ACT_P_DELETED) {
+		if (ret == ACT_P_DELETED)
 			module_put(ops->owner);
-			n_i++;
-		} else if (ret < 0) {
-			mutex_unlock(&idrinfo->lock);
-			goto nla_put_failure;
-		}
+		else if (ret < 0)
+			break;
+		n_i++;
 	}
 	mutex_unlock(&idrinfo->lock);
+	if (ret < 0) {
+		if (n_i)
+			NL_SET_ERR_MSG(extack, "Unable to flush all TC actions");
+		else
+			goto nla_put_failure;
+	}
 
 	ret = nla_put_u32(skb, TCA_FCNT, n_i);
 	if (ret)
@@ -400,7 +406,7 @@
 	struct tcf_idrinfo *idrinfo = tn->idrinfo;
 
 	if (type == RTM_DELACTION) {
-		return tcf_del_walker(idrinfo, skb, ops);
+		return tcf_del_walker(idrinfo, skb, ops, extack);
 	} else if (type == RTM_GETACTION) {
 		return tcf_dump_walker(idrinfo, skb, cb);
 	} else {
@@ -549,6 +555,9 @@
  * its reference and bind counters, and return 1. Otherwise insert temporary
  * error pointer (to prevent concurrent users from inserting actions with same
  * index) and return 0.
+ *
+ * May return -EAGAIN for binding actions in case of a parallel add/delete on
+ * the requested index.
  */
 
 int tcf_idr_check_alloc(struct tc_action_net *tn, u32 *index,
@@ -557,43 +566,60 @@
 	struct tcf_idrinfo *idrinfo = tn->idrinfo;
 	struct tc_action *p;
 	int ret;
+	u32 max;
 
-again:
-	mutex_lock(&idrinfo->lock);
 	if (*index) {
+		rcu_read_lock();
 		p = idr_find(&idrinfo->action_idr, *index);
+
 		if (IS_ERR(p)) {
 			/* This means that another process allocated
 			 * index but did not assign the pointer yet.
 			 */
-			mutex_unlock(&idrinfo->lock);
-			goto again;
+			rcu_read_unlock();
+			return -EAGAIN;
+		}
+
+		if (!p) {
+			/* Empty slot, try to allocate it */
+			max = *index;
+			rcu_read_unlock();
+			goto new;
 		}
 
-		if (p) {
-			refcount_inc(&p->tcfa_refcnt);
-			if (bind)
-				atomic_inc(&p->tcfa_bindcnt);
-			*a = p;
-			ret = 1;
-		} else {
-			*a = NULL;
-			ret = idr_alloc_u32(&idrinfo->action_idr, NULL, index,
-					    *index, GFP_KERNEL);
-			if (!ret)
-				idr_replace(&idrinfo->action_idr,
-					    ERR_PTR(-EBUSY), *index);
+		if (!refcount_inc_not_zero(&p->tcfa_refcnt)) {
+			/* Action was deleted in parallel */
+			rcu_read_unlock();
+			return -EAGAIN;
 		}
+
+		if (bind)
+			atomic_inc(&p->tcfa_bindcnt);
+		*a = p;
+
+		rcu_read_unlock();
+
+		return 1;
 	} else {
+		/* Find a slot */
 		*index = 1;
-		*a = NULL;
-		ret = idr_alloc_u32(&idrinfo->action_idr, NULL, index,
-				    UINT_MAX, GFP_KERNEL);
-		if (!ret)
-			idr_replace(&idrinfo->action_idr, ERR_PTR(-EBUSY),
-				    *index);
+		max = UINT_MAX;
 	}
+
+new:
+	*a = NULL;
+
+	mutex_lock(&idrinfo->lock);
+	ret = idr_alloc_u32(&idrinfo->action_idr, ERR_PTR(-EBUSY), index, max,
+			    GFP_KERNEL);
 	mutex_unlock(&idrinfo->lock);
+
+	/* N binds raced for action allocation,
+	 * retry for all the ones that failed.
+	 */
+	if (ret == -ENOSPC && *index == max)
+		ret = -EAGAIN;
+
 	return ret;
 }
 EXPORT_SYMBOL(tcf_idr_check_alloc);
@@ -728,15 +754,24 @@
 restart_act_graph:
 	for (i = 0; i < nr_actions; i++) {
 		const struct tc_action *a = actions[i];
+		int repeat_ttl;
 
 		if (jmp_prgcnt > 0) {
 			jmp_prgcnt -= 1;
 			continue;
 		}
+
+		repeat_ttl = 32;
 repeat:
 		ret = a->ops->act(skb, a, res);
-		if (ret == TC_ACT_REPEAT)
-			goto repeat;	/* we need a ttl - JHS */
+
+		if (unlikely(ret == TC_ACT_REPEAT)) {
+			if (--repeat_ttl != 0)
+				goto repeat;
+			/* suspicious opcode, stop pipeline */
+			net_warn_ratelimited("TC_ACT_REPEAT abuse ?\n");
+			return TC_ACT_OK;
+		}
 
 		if (TC_ACT_EXT_CMP(ret, TC_ACT_JUMP)) {
 			jmp_prgcnt = ret & TCA_ACT_MAX_PRIO_MASK;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_bpf.c
@@ -305,7 +305,7 @@
 	ret = tcf_idr_check_alloc(tn, &index, act, bind);
 	if (!ret) {
 		ret = tcf_idr_create(tn, index, est, act,
-				     &act_bpf_ops, bind, true, 0);
+				     &act_bpf_ops, bind, true, flags);
 		if (ret < 0) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_connmark.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_connmark.c
@@ -62,7 +62,7 @@
 
 	c = nf_ct_get(skb, &ctinfo);
 	if (c) {
-		skb->mark = c->mark;
+		skb->mark = READ_ONCE(c->mark);
 		/* using overlimits stats to count how many packets marked */
 		ca->tcf_qstats.overlimits++;
 		goto out;
@@ -82,7 +82,7 @@
 	c = nf_ct_tuplehash_to_ctrack(thash);
 	/* using overlimits stats to count how many packets marked */
 	ca->tcf_qstats.overlimits++;
-	skb->mark = c->mark;
+	skb->mark = READ_ONCE(c->mark);
 	nf_ct_put(c);
 
 out:
@@ -124,7 +124,7 @@
 	ret = tcf_idr_check_alloc(tn, &index, a, bind);
 	if (!ret) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_connmark_ops, bind, false, 0);
+				     &act_connmark_ops, bind, false, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_ct.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_ct.c
@@ -38,21 +38,28 @@
 static struct rhashtable zones_ht;
 static DEFINE_MUTEX(zones_mutex);
 
+struct zones_ht_key {
+	struct net *net;
+	u16 zone;
+	/* Note : pad[] must be the last field. */
+	u8  pad[];
+};
+
 struct tcf_ct_flow_table {
 	struct rhash_head node; /* In zones tables */
 
 	struct rcu_work rwork;
 	struct nf_flowtable nf_ft;
 	refcount_t ref;
-	u16 zone;
+	struct zones_ht_key key;
 
 	bool dying;
 };
 
 static const struct rhashtable_params zones_params = {
 	.head_offset = offsetof(struct tcf_ct_flow_table, node),
-	.key_offset = offsetof(struct tcf_ct_flow_table, zone),
-	.key_len = sizeof_field(struct tcf_ct_flow_table, zone),
+	.key_offset = offsetof(struct tcf_ct_flow_table, key),
+	.key_len = offsetof(struct zones_ht_key, pad),
 	.automatic_shrinking = true,
 };
 
@@ -177,7 +184,7 @@
 	entry = tcf_ct_flow_table_flow_action_get_next(action);
 	entry->id = FLOW_ACTION_CT_METADATA;
 #if IS_ENABLED(CONFIG_NF_CONNTRACK_MARK)
-	entry->ct_metadata.mark = ct->mark;
+	entry->ct_metadata.mark = READ_ONCE(ct->mark);
 #endif
 	ctinfo = dir == IP_CT_DIR_ORIGINAL ? IP_CT_ESTABLISHED :
 					     IP_CT_ESTABLISHED_REPLY;
@@ -276,13 +283,14 @@
 	.owner		= THIS_MODULE,
 };
 
-static int tcf_ct_flow_table_get(struct tcf_ct_params *params)
+static int tcf_ct_flow_table_get(struct net *net, struct tcf_ct_params *params)
 {
+	struct zones_ht_key key = { .net = net, .zone = params->zone };
 	struct tcf_ct_flow_table *ct_ft;
 	int err = -ENOMEM;
 
 	mutex_lock(&zones_mutex);
-	ct_ft = rhashtable_lookup_fast(&zones_ht, &params->zone, zones_params);
+	ct_ft = rhashtable_lookup_fast(&zones_ht, &key, zones_params);
 	if (ct_ft && refcount_inc_not_zero(&ct_ft->ref))
 		goto out_unlock;
 
@@ -291,7 +299,7 @@
 		goto err_alloc;
 	refcount_set(&ct_ft->ref, 1);
 
-	ct_ft->zone = params->zone;
+	ct_ft->key = key;
 	err = rhashtable_insert_fast(&zones_ht, &ct_ft->node, zones_params);
 	if (err)
 		goto err_insert;
@@ -302,6 +310,7 @@
 	err = nf_flow_table_init(&ct_ft->nf_ft);
 	if (err)
 		goto err_init;
+	write_pnet(&ct_ft->nf_ft.net, net);
 
 	__module_get(THIS_MODULE);
 out_unlock:
@@ -516,11 +525,6 @@
 	struct nf_conn *ct;
 	u8 dir;
 
-	/* Previously seen or loopback */
-	ct = nf_ct_get(skb, &ctinfo);
-	if ((ct && !nf_ct_is_template(ct)) || ctinfo == IP_CT_UNTRACKED)
-		return false;
-
 	switch (family) {
 	case NFPROTO_IPV4:
 		if (!tcf_ct_flow_table_fill_tuple_ipv4(skb, &tuple, &tcph))
@@ -588,22 +592,25 @@
 	if (!ct)
 		return false;
 	if (!net_eq(net, read_pnet(&ct->ct_net)))
-		return false;
+		goto drop_ct;
 	if (nf_ct_zone(ct)->id != zone_id)
-		return false;
+		goto drop_ct;
 
 	/* Force conntrack entry direction. */
 	if (force && CTINFO2DIR(ctinfo) != IP_CT_DIR_ORIGINAL) {
 		if (nf_ct_is_confirmed(ct))
 			nf_ct_kill(ct);
 
-		nf_conntrack_put(&ct->ct_general);
-		nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
-
-		return false;
+		goto drop_ct;
 	}
 
 	return true;
+
+drop_ct:
+	nf_ct_put(ct);
+	nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
+
+	return false;
 }
 
 /* Trim the skb to the length specified by the IP/IPv6 header,
@@ -690,10 +697,10 @@
 				   u8 family, u16 zone, bool *defrag)
 {
 	enum ip_conntrack_info ctinfo;
-	struct qdisc_skb_cb cb;
 	struct nf_conn *ct;
 	int err = 0;
 	bool frag;
+	u16 mru;
 
 	/* Previously seen (loopback)? Ignore. */
 	ct = nf_ct_get(skb, &ctinfo);
@@ -707,8 +714,7 @@
 	if (err || !frag)
 		return err;
 
-	skb_get(skb);
-	cb = *qdisc_skb_cb(skb);
+	mru = tc_skb_cb(skb)->mru;
 
 	if (family == NFPROTO_IPV4) {
 		enum ip_defrag_users user = IP_DEFRAG_CONNTRACK_IN + zone;
@@ -722,7 +728,7 @@
 
 		if (!err) {
 			*defrag = true;
-			cb.mru = IPCB(skb)->frag_max_size;
+			mru = IPCB(skb)->frag_max_size;
 		}
 	} else { /* NFPROTO_IPV6 */
 #if IS_ENABLED(CONFIG_NF_DEFRAG_IPV6)
@@ -735,7 +741,7 @@
 
 		if (!err) {
 			*defrag = true;
-			cb.mru = IP6CB(skb)->frag_max_size;
+			mru = IP6CB(skb)->frag_max_size;
 		}
 #else
 		err = -EOPNOTSUPP;
@@ -744,7 +750,7 @@
 	}
 
 	if (err != -EINPROGRESS)
-		*qdisc_skb_cb(skb) = cb;
+		tc_skb_cb(skb)->mru = mru;
 	skb_clear_hash(skb);
 	skb->ignore_df = 1;
 	return err;
@@ -762,7 +768,7 @@
 	tcf_ct_flow_table_put(params);
 
 	if (params->tmpl)
-		nf_conntrack_put(&params->tmpl->ct_general);
+		nf_ct_put(params->tmpl);
 	kfree(params);
 }
 
@@ -839,6 +845,12 @@
 	}
 
 	err = nf_nat_packet(ct, ctinfo, hooknum, skb);
+	if (err == NF_ACCEPT) {
+		if (maniptype == NF_NAT_MANIP_SRC)
+			tc_skb_cb(skb)->post_ct_snat = 1;
+		if (maniptype == NF_NAT_MANIP_DST)
+			tc_skb_cb(skb)->post_ct_dnat = 1;
+	}
 out:
 	return err;
 }
@@ -852,9 +864,9 @@
 	if (!mask)
 		return;
 
-	new_mark = mark | (ct->mark & ~(mask));
-	if (ct->mark != new_mark) {
-		ct->mark = new_mark;
+	new_mark = mark | (READ_ONCE(ct->mark) & ~(mask));
+	if (READ_ONCE(ct->mark) != new_mark) {
+		WRITE_ONCE(ct->mark, new_mark);
 		if (nf_ct_is_confirmed(ct))
 			nf_conntrack_event_cache(IPCT_MARK, ct);
 	}
@@ -963,10 +975,10 @@
 	tcf_action_update_bstats(&c->common, skb);
 
 	if (clear) {
-		qdisc_skb_cb(skb)->post_ct = false;
+		tc_skb_cb(skb)->post_ct = false;
 		ct = nf_ct_get(skb, &ctinfo);
 		if (ct) {
-			nf_conntrack_put(&ct->ct_general);
+			nf_ct_put(ct);
 			nf_ct_set(skb, NULL, IP_CT_UNTRACKED);
 		}
 
@@ -983,12 +995,8 @@
 	nh_ofs = skb_network_offset(skb);
 	skb_pull_rcsum(skb, nh_ofs);
 	err = tcf_ct_handle_fragments(net, skb, family, p->zone, &defrag);
-	if (err == -EINPROGRESS) {
-		retval = TC_ACT_STOLEN;
-		goto out_clear;
-	}
 	if (err)
-		goto drop;
+		goto out_frag;
 
 	err = tcf_ct_skb_network_trim(skb, family);
 	if (err)
@@ -1040,6 +1048,14 @@
 		 */
 		if (nf_conntrack_confirm(skb) != NF_ACCEPT)
 			goto drop;
+
+		/* The ct may be dropped if a clash has been resolved,
+		 * so it's necessary to retrieve it from skb again to
+		 * prevent UAF.
+		 */
+		ct = nf_ct_get(skb, &ctinfo);
+		if (!ct)
+			skip_add = true;
 	}
 
 	if (!skip_add)
@@ -1048,12 +1064,18 @@
 out_push:
 	skb_push_rcsum(skb, nh_ofs);
 
-	qdisc_skb_cb(skb)->post_ct = true;
+	tc_skb_cb(skb)->post_ct = true;
+	tc_skb_cb(skb)->zone = p->zone;
 out_clear:
 	if (defrag)
 		qdisc_skb_cb(skb)->pkt_len = skb->len;
 	return retval;
 
+out_frag:
+	if (err != -EINPROGRESS)
+		tcf_action_inc_drop_qstats(&c->common);
+	return TC_ACT_CONSUMED;
+
 drop:
 	tcf_action_inc_drop_qstats(&c->common);
 	return TC_ACT_SHOT;
@@ -1227,7 +1249,6 @@
 		return -ENOMEM;
 	}
 	__set_bit(IPS_CONFIRMED_BIT, &tmpl->status);
-	nf_conntrack_get(&tmpl->ct_general);
 	p->tmpl = tmpl;
 
 	return 0;
@@ -1300,9 +1321,9 @@
 	if (err)
 		goto cleanup;
 
-	err = tcf_ct_flow_table_get(params);
+	err = tcf_ct_flow_table_get(net, params);
 	if (err)
-		goto cleanup;
+		goto cleanup_params;
 
 	spin_lock_bh(&c->tcf_lock);
 	goto_ch = tcf_action_set_ctrlact(*a, parm->action, goto_ch);
@@ -1317,6 +1338,9 @@
 
 	return res;
 
+cleanup_params:
+	if (params->tmpl)
+		nf_ct_put(params->tmpl);
 cleanup:
 	if (goto_ch)
 		tcf_chain_put_by_act(goto_ch);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_ctinfo.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_ctinfo.c
@@ -33,7 +33,7 @@
 {
 	u8 dscp, newdscp;
 
-	newdscp = (((ct->mark & cp->dscpmask) >> cp->dscpmaskshift) << 2) &
+	newdscp = (((READ_ONCE(ct->mark) & cp->dscpmask) >> cp->dscpmaskshift) << 2) &
 		     ~INET_ECN_MASK;
 
 	switch (proto) {
@@ -73,7 +73,7 @@
 				  struct sk_buff *skb)
 {
 	ca->stats_cpmark_set++;
-	skb->mark = ct->mark & cp->cpmarkmask;
+	skb->mark = READ_ONCE(ct->mark) & cp->cpmarkmask;
 }
 
 static int tcf_ctinfo_act(struct sk_buff *skb, const struct tc_action *a,
@@ -92,7 +92,7 @@
 	cp = rcu_dereference_bh(ca->params);
 
 	tcf_lastuse_update(&ca->tcf_tm);
-	bstats_update(&ca->tcf_bstats, skb);
+	tcf_action_update_bstats(&ca->common, skb);
 	action = READ_ONCE(ca->tcf_action);
 
 	wlen = skb_network_offset(skb);
@@ -131,7 +131,7 @@
 	}
 
 	if (cp->mode & CTINFO_MODE_DSCP)
-		if (!cp->dscpstatemask || (ct->mark & cp->dscpstatemask))
+		if (!cp->dscpstatemask || (READ_ONCE(ct->mark) & cp->dscpstatemask))
 			tcf_ctinfo_dscp_set(ct, ca, cp, skb, wlen, proto);
 
 	if (cp->mode & CTINFO_MODE_CPMARK)
@@ -211,8 +211,8 @@
 	index = actparm->index;
 	err = tcf_idr_check_alloc(tn, &index, a, bind);
 	if (!err) {
-		ret = tcf_idr_create(tn, index, est, a,
-				     &act_ctinfo_ops, bind, false, 0);
+		ret = tcf_idr_create_from_flags(tn, index, est, a,
+						&act_ctinfo_ops, bind, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_gate.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_gate.c
@@ -357,7 +357,7 @@
 
 	if (!err) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_gate_ops, bind, false, 0);
+				     &act_gate_ops, bind, false, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_ife.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_ife.c
@@ -553,7 +553,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, est, a, &act_ife_ops,
-				     bind, true, 0);
+				     bind, true, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			kfree(p);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_ipt.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_ipt.c
@@ -50,7 +50,7 @@
 	par.entryinfo = &e;
 	par.target    = target;
 	par.targinfo  = t->data;
-	par.hook_mask = hook;
+	par.hook_mask = 1 << hook;
 	par.family    = NFPROTO_IPV4;
 
 	ret = xt_check_target(&par, t->u.target_size - sizeof(*t), 0, false);
@@ -87,7 +87,8 @@
 
 static const struct nla_policy ipt_policy[TCA_IPT_MAX + 1] = {
 	[TCA_IPT_TABLE]	= { .type = NLA_STRING, .len = IFNAMSIZ },
-	[TCA_IPT_HOOK]	= { .type = NLA_U32 },
+	[TCA_IPT_HOOK]	= NLA_POLICY_RANGE(NLA_U32, NF_INET_PRE_ROUTING,
+					   NF_INET_NUMHOOKS),
 	[TCA_IPT_INDEX]	= { .type = NLA_U32 },
 	[TCA_IPT_TARG]	= { .len = sizeof(struct xt_entry_target) },
 };
@@ -145,7 +146,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, est, a, ops, bind,
-				     false, 0);
+				     false, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
@@ -160,15 +161,27 @@
 			return -EEXIST;
 		}
 	}
+
+	err = -EINVAL;
 	hook = nla_get_u32(tb[TCA_IPT_HOOK]);
+	switch (hook) {
+	case NF_INET_PRE_ROUTING:
+		break;
+	case NF_INET_POST_ROUTING:
+		break;
+	default:
+		goto err1;
+	}
+
+	if (tb[TCA_IPT_TABLE]) {
+		/* mangle only for now */
+		if (nla_strcmp(tb[TCA_IPT_TABLE], "mangle"))
+			goto err1;
+	}
 
-	err = -ENOMEM;
-	tname = kmalloc(IFNAMSIZ, GFP_KERNEL);
+	tname = kstrdup("mangle", GFP_KERNEL);
 	if (unlikely(!tname))
 		goto err1;
-	if (tb[TCA_IPT_TABLE] == NULL ||
-	    nla_strscpy(tname, tb[TCA_IPT_TABLE], IFNAMSIZ) >= IFNAMSIZ)
-		strcpy(tname, "mangle");
 
 	t = kmemdup(td, td->u.target_size, GFP_KERNEL);
 	if (unlikely(!t))
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_mirred.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_mirred.c
@@ -19,6 +19,7 @@
 #include <linux/if_arp.h>
 #include <net/net_namespace.h>
 #include <net/netlink.h>
+#include <net/dst.h>
 #include <net/pkt_sched.h>
 #include <net/pkt_cls.h>
 #include <linux/tc_act/tc_mirred.h>
@@ -27,8 +28,8 @@
 static LIST_HEAD(mirred_list);
 static DEFINE_SPINLOCK(mirred_list_lock);
 
-#define MIRRED_RECURSION_LIMIT    4
-static DEFINE_PER_CPU(unsigned int, mirred_rec_level);
+#define MIRRED_NEST_LIMIT    4
+static DEFINE_PER_CPU(unsigned int, mirred_nest_level);
 
 static bool tcf_mirred_is_act_redirect(int action)
 {
@@ -203,12 +204,19 @@
 	return err;
 }
 
+static bool is_mirred_nested(void)
+{
+	return unlikely(__this_cpu_read(mirred_nest_level) > 1);
+}
+
 static int tcf_mirred_forward(bool want_ingress, struct sk_buff *skb)
 {
 	int err;
 
 	if (!want_ingress)
 		err = tcf_dev_queue_xmit(skb, dev_queue_xmit);
+	else if (is_mirred_nested())
+		err = netif_rx(skb);
 	else
 		err = netif_receive_skb(skb);
 
@@ -222,21 +230,22 @@
 	struct sk_buff *skb2 = skb;
 	bool m_mac_header_xmit;
 	struct net_device *dev;
-	unsigned int rec_level;
+	unsigned int nest_level;
 	int retval, err = 0;
 	bool use_reinsert;
 	bool want_ingress;
 	bool is_redirect;
 	bool expects_nh;
+	bool at_ingress;
 	int m_eaction;
 	int mac_len;
 	bool at_nh;
 
-	rec_level = __this_cpu_inc_return(mirred_rec_level);
-	if (unlikely(rec_level > MIRRED_RECURSION_LIMIT)) {
+	nest_level = __this_cpu_inc_return(mirred_nest_level);
+	if (unlikely(nest_level > MIRRED_NEST_LIMIT)) {
 		net_warn_ratelimited("Packet exceeded mirred recursion limit on dev %s\n",
 				     netdev_name(skb->dev));
-		__this_cpu_dec(mirred_rec_level);
+		__this_cpu_dec(mirred_nest_level);
 		return TC_ACT_SHOT;
 	}
 
@@ -252,7 +261,7 @@
 		goto out;
 	}
 
-	if (unlikely(!(dev->flags & IFF_UP))) {
+	if (unlikely(!(dev->flags & IFF_UP)) || !netif_carrier_ok(dev)) {
 		net_notice_ratelimited("tc mirred to Houston: device %s is down\n",
 				       dev->name);
 		goto out;
@@ -263,7 +272,8 @@
 	 * ingress - that covers the TC S/W datapath.
 	 */
 	is_redirect = tcf_mirred_is_act_redirect(m_eaction);
-	use_reinsert = skb_at_tc_ingress(skb) && is_redirect &&
+	at_ingress = skb_at_tc_ingress(skb);
+	use_reinsert = at_ingress && is_redirect &&
 		       tcf_mirred_can_reinsert(retval);
 	if (!use_reinsert) {
 		skb2 = skb_clone(skb, GFP_ATOMIC);
@@ -271,10 +281,12 @@
 			goto out;
 	}
 
+	want_ingress = tcf_mirred_act_wants_ingress(m_eaction);
+
 	/* All mirred/redirected skbs should clear previous ct info */
 	nf_reset_ct(skb2);
-
-	want_ingress = tcf_mirred_act_wants_ingress(m_eaction);
+	if (want_ingress && !at_ingress) /* drop dst for egress -> ingress */
+		skb_dst_drop(skb2);
 
 	expects_nh = want_ingress || !m_mac_header_xmit;
 	at_nh = skb->data == skb_network_header(skb);
@@ -303,7 +315,7 @@
 			err = tcf_mirred_forward(res->ingress, skb);
 			if (err)
 				tcf_action_inc_overlimit_qstats(&m->common);
-			__this_cpu_dec(mirred_rec_level);
+			__this_cpu_dec(mirred_nest_level);
 			return TC_ACT_CONSUMED;
 		}
 	}
@@ -315,7 +327,7 @@
 		if (tcf_mirred_is_act_redirect(m_eaction))
 			retval = TC_ACT_SHOT;
 	}
-	__this_cpu_dec(mirred_rec_level);
+	__this_cpu_dec(mirred_nest_level);
 
 	return retval;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_mpls.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_mpls.c
@@ -133,6 +133,11 @@
 {
 	const u32 *label = nla_data(attr);
 
+	if (nla_len(attr) != sizeof(*label)) {
+		NL_SET_ERR_MSG_MOD(extack, "Invalid MPLS label length");
+		return -EINVAL;
+	}
+
 	if (*label & ~MPLS_LABEL_MASK || *label == MPLS_LABEL_IMPLNULL) {
 		NL_SET_ERR_MSG_MOD(extack, "MPLS label out of range");
 		return -EINVAL;
@@ -144,7 +149,8 @@
 static const struct nla_policy mpls_policy[TCA_MPLS_MAX + 1] = {
 	[TCA_MPLS_PARMS]	= NLA_POLICY_EXACT_LEN(sizeof(struct tc_mpls)),
 	[TCA_MPLS_PROTO]	= { .type = NLA_U16 },
-	[TCA_MPLS_LABEL]	= NLA_POLICY_VALIDATE_FN(NLA_U32, valid_label),
+	[TCA_MPLS_LABEL]	= NLA_POLICY_VALIDATE_FN(NLA_BINARY,
+							 valid_label),
 	[TCA_MPLS_TC]		= NLA_POLICY_RANGE(NLA_U8, 0, 7),
 	[TCA_MPLS_TTL]		= NLA_POLICY_MIN(NLA_U8, 1),
 	[TCA_MPLS_BOS]		= NLA_POLICY_RANGE(NLA_U8, 0, 1),
@@ -183,40 +189,67 @@
 	parm = nla_data(tb[TCA_MPLS_PARMS]);
 	index = parm->index;
 
+	err = tcf_idr_check_alloc(tn, &index, a, bind);
+	if (err < 0)
+		return err;
+	exists = err;
+	if (exists && bind)
+		return 0;
+
+	if (!exists) {
+		ret = tcf_idr_create(tn, index, est, a, &act_mpls_ops, bind,
+				     true, flags);
+		if (ret) {
+			tcf_idr_cleanup(tn, index);
+			return ret;
+		}
+
+		ret = ACT_P_CREATED;
+	} else if (!(flags & TCA_ACT_FLAGS_REPLACE)) {
+		tcf_idr_release(*a, bind);
+		return -EEXIST;
+	}
+
 	/* Verify parameters against action type. */
 	switch (parm->m_action) {
 	case TCA_MPLS_ACT_POP:
 		if (!tb[TCA_MPLS_PROTO]) {
 			NL_SET_ERR_MSG_MOD(extack, "Protocol must be set for MPLS pop");
-			return -EINVAL;
+			err = -EINVAL;
+			goto release_idr;
 		}
 		if (!eth_proto_is_802_3(nla_get_be16(tb[TCA_MPLS_PROTO]))) {
 			NL_SET_ERR_MSG_MOD(extack, "Invalid protocol type for MPLS pop");
-			return -EINVAL;
+			err = -EINVAL;
+			goto release_idr;
 		}
 		if (tb[TCA_MPLS_LABEL] || tb[TCA_MPLS_TTL] || tb[TCA_MPLS_TC] ||
 		    tb[TCA_MPLS_BOS]) {
 			NL_SET_ERR_MSG_MOD(extack, "Label, TTL, TC or BOS cannot be used with MPLS pop");
-			return -EINVAL;
+			err = -EINVAL;
+			goto release_idr;
 		}
 		break;
 	case TCA_MPLS_ACT_DEC_TTL:
 		if (tb[TCA_MPLS_PROTO] || tb[TCA_MPLS_LABEL] ||
 		    tb[TCA_MPLS_TTL] || tb[TCA_MPLS_TC] || tb[TCA_MPLS_BOS]) {
 			NL_SET_ERR_MSG_MOD(extack, "Label, TTL, TC, BOS or protocol cannot be used with MPLS dec_ttl");
-			return -EINVAL;
+			err = -EINVAL;
+			goto release_idr;
 		}
 		break;
 	case TCA_MPLS_ACT_PUSH:
 	case TCA_MPLS_ACT_MAC_PUSH:
 		if (!tb[TCA_MPLS_LABEL]) {
 			NL_SET_ERR_MSG_MOD(extack, "Label is required for MPLS push");
-			return -EINVAL;
+			err = -EINVAL;
+			goto release_idr;
 		}
 		if (tb[TCA_MPLS_PROTO] &&
 		    !eth_p_mpls(nla_get_be16(tb[TCA_MPLS_PROTO]))) {
 			NL_SET_ERR_MSG_MOD(extack, "Protocol must be an MPLS type for MPLS push");
-			return -EPROTONOSUPPORT;
+			err = -EPROTONOSUPPORT;
+			goto release_idr;
 		}
 		/* Push needs a TTL - if not specified, set a default value. */
 		if (!tb[TCA_MPLS_TTL]) {
@@ -231,33 +264,14 @@
 	case TCA_MPLS_ACT_MODIFY:
 		if (tb[TCA_MPLS_PROTO]) {
 			NL_SET_ERR_MSG_MOD(extack, "Protocol cannot be used with MPLS modify");
-			return -EINVAL;
+			err = -EINVAL;
+			goto release_idr;
 		}
 		break;
 	default:
 		NL_SET_ERR_MSG_MOD(extack, "Unknown MPLS action");
-		return -EINVAL;
-	}
-
-	err = tcf_idr_check_alloc(tn, &index, a, bind);
-	if (err < 0)
-		return err;
-	exists = err;
-	if (exists && bind)
-		return 0;
-
-	if (!exists) {
-		ret = tcf_idr_create(tn, index, est, a,
-				     &act_mpls_ops, bind, true, 0);
-		if (ret) {
-			tcf_idr_cleanup(tn, index);
-			return ret;
-		}
-
-		ret = ACT_P_CREATED;
-	} else if (!(flags & TCA_ACT_FLAGS_REPLACE)) {
-		tcf_idr_release(*a, bind);
-		return -EEXIST;
+		err = -EINVAL;
+		goto release_idr;
 	}
 
 	err = tcf_action_check_ctrlact(parm->action, tp, &goto_ch, extack);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_nat.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_nat.c
@@ -61,7 +61,7 @@
 	err = tcf_idr_check_alloc(tn, &index, a, bind);
 	if (!err) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_nat_ops, bind, false, 0);
+				     &act_nat_ops, bind, false, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_pedit.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_pedit.c
@@ -13,7 +13,10 @@
 #include <linux/rtnetlink.h>
 #include <linux/module.h>
 #include <linux/init.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
 #include <linux/slab.h>
+#include <net/ipv6.h>
 #include <net/netlink.h>
 #include <net/pkt_sched.h>
 #include <linux/tc_act/tc_pedit.h>
@@ -26,6 +29,7 @@
 
 static const struct nla_policy pedit_policy[TCA_PEDIT_MAX + 1] = {
 	[TCA_PEDIT_PARMS]	= { .len = sizeof(struct tc_pedit) },
+	[TCA_PEDIT_PARMS_EX]	= { .len = sizeof(struct tc_pedit) },
 	[TCA_PEDIT_KEYS_EX]   = { .type = NLA_NESTED },
 };
 
@@ -134,6 +138,17 @@
 	return -EINVAL;
 }
 
+static void tcf_pedit_cleanup_rcu(struct rcu_head *head)
+{
+	struct tcf_pedit_parms *parms =
+		container_of(head, struct tcf_pedit_parms, rcu);
+
+	kfree(parms->tcfp_keys_ex);
+	kfree(parms->tcfp_keys);
+
+	kfree(parms);
+}
+
 static int tcf_pedit_init(struct net *net, struct nlattr *nla,
 			  struct nlattr *est, struct tc_action **a,
 			  struct tcf_proto *tp, u32 flags,
@@ -141,15 +156,14 @@
 {
 	struct tc_action_net *tn = net_generic(net, pedit_net_id);
 	bool bind = flags & TCA_ACT_FLAGS_BIND;
-	struct nlattr *tb[TCA_PEDIT_MAX + 1];
 	struct tcf_chain *goto_ch = NULL;
-	struct tc_pedit_key *keys = NULL;
-	struct tcf_pedit_key_ex *keys_ex;
+	struct tcf_pedit_parms *oparms, *nparms;
+	struct nlattr *tb[TCA_PEDIT_MAX + 1];
 	struct tc_pedit *parm;
 	struct nlattr *pattr;
 	struct tcf_pedit *p;
 	int ret = 0, err;
-	int ksize;
+	int i, ksize;
 	u32 index;
 
 	if (!nla) {
@@ -171,93 +185,125 @@
 	}
 
 	parm = nla_data(pattr);
-	if (!parm->nkeys) {
-		NL_SET_ERR_MSG_MOD(extack, "Pedit requires keys to be passed");
-		return -EINVAL;
-	}
-	ksize = parm->nkeys * sizeof(struct tc_pedit_key);
-	if (nla_len(pattr) < sizeof(*parm) + ksize) {
-		NL_SET_ERR_MSG_ATTR(extack, pattr, "Length of TCA_PEDIT_PARMS or TCA_PEDIT_PARMS_EX pedit attribute is invalid");
-		return -EINVAL;
-	}
-
-	keys_ex = tcf_pedit_keys_ex_parse(tb[TCA_PEDIT_KEYS_EX], parm->nkeys);
-	if (IS_ERR(keys_ex))
-		return PTR_ERR(keys_ex);
 
 	index = parm->index;
 	err = tcf_idr_check_alloc(tn, &index, a, bind);
 	if (!err) {
-		ret = tcf_idr_create(tn, index, est, a,
-				     &act_pedit_ops, bind, false, 0);
+		ret = tcf_idr_create_from_flags(tn, index, est, a,
+						&act_pedit_ops, bind, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
-			goto out_free;
+			return ret;
 		}
 		ret = ACT_P_CREATED;
 	} else if (err > 0) {
 		if (bind)
-			goto out_free;
+			return 0;
 		if (!(flags & TCA_ACT_FLAGS_REPLACE)) {
 			ret = -EEXIST;
 			goto out_release;
 		}
 	} else {
-		ret = err;
+		return err;
+	}
+
+	if (!parm->nkeys) {
+		NL_SET_ERR_MSG_MOD(extack, "Pedit requires keys to be passed");
+		ret = -EINVAL;
+		goto out_release;
+	}
+	ksize = parm->nkeys * sizeof(struct tc_pedit_key);
+	if (nla_len(pattr) < sizeof(*parm) + ksize) {
+		NL_SET_ERR_MSG_ATTR(extack, pattr, "Length of TCA_PEDIT_PARMS or TCA_PEDIT_PARMS_EX pedit attribute is invalid");
+		ret = -EINVAL;
+		goto out_release;
+	}
+
+	nparms = kzalloc(sizeof(*nparms), GFP_KERNEL);
+	if (!nparms) {
+		ret = -ENOMEM;
+		goto out_release;
+	}
+
+	nparms->tcfp_keys_ex =
+		tcf_pedit_keys_ex_parse(tb[TCA_PEDIT_KEYS_EX], parm->nkeys);
+	if (IS_ERR(nparms->tcfp_keys_ex)) {
+		ret = PTR_ERR(nparms->tcfp_keys_ex);
 		goto out_free;
 	}
 
 	err = tcf_action_check_ctrlact(parm->action, tp, &goto_ch, extack);
 	if (err < 0) {
 		ret = err;
-		goto out_release;
+		goto out_free_ex;
 	}
-	p = to_pedit(*a);
-	spin_lock_bh(&p->tcf_lock);
 
-	if (ret == ACT_P_CREATED ||
-	    (p->tcfp_nkeys && p->tcfp_nkeys != parm->nkeys)) {
-		keys = kmalloc(ksize, GFP_ATOMIC);
-		if (!keys) {
-			spin_unlock_bh(&p->tcf_lock);
-			ret = -ENOMEM;
-			goto put_chain;
-		}
-		kfree(p->tcfp_keys);
-		p->tcfp_keys = keys;
-		p->tcfp_nkeys = parm->nkeys;
+	nparms->tcfp_off_max_hint = 0;
+	nparms->tcfp_flags = parm->flags;
+	nparms->tcfp_nkeys = parm->nkeys;
+
+	nparms->tcfp_keys = kmalloc(ksize, GFP_KERNEL);
+	if (!nparms->tcfp_keys) {
+		ret = -ENOMEM;
+		goto put_chain;
 	}
-	memcpy(p->tcfp_keys, parm->keys, ksize);
 
-	p->tcfp_flags = parm->flags;
-	goto_ch = tcf_action_set_ctrlact(*a, parm->action, goto_ch);
+	memcpy(nparms->tcfp_keys, parm->keys, ksize);
+
+	for (i = 0; i < nparms->tcfp_nkeys; ++i) {
+		u32 cur = nparms->tcfp_keys[i].off;
+
+		/* sanitize the shift value for any later use */
+		nparms->tcfp_keys[i].shift = min_t(size_t,
+						   BITS_PER_TYPE(int) - 1,
+						   nparms->tcfp_keys[i].shift);
+
+		/* The AT option can read a single byte, we can bound the actual
+		 * value with uchar max.
+		 */
+		cur += (0xff & nparms->tcfp_keys[i].offmask) >> nparms->tcfp_keys[i].shift;
 
-	kfree(p->tcfp_keys_ex);
-	p->tcfp_keys_ex = keys_ex;
+		/* Each key touches 4 bytes starting from the computed offset */
+		nparms->tcfp_off_max_hint =
+			max(nparms->tcfp_off_max_hint, cur + 4);
+	}
+
+	p = to_pedit(*a);
 
+	spin_lock_bh(&p->tcf_lock);
+	goto_ch = tcf_action_set_ctrlact(*a, parm->action, goto_ch);
+	oparms = rcu_replace_pointer(p->parms, nparms, 1);
 	spin_unlock_bh(&p->tcf_lock);
+
+	if (oparms)
+		call_rcu(&oparms->rcu, tcf_pedit_cleanup_rcu);
+
 	if (goto_ch)
 		tcf_chain_put_by_act(goto_ch);
+
 	return ret;
 
 put_chain:
 	if (goto_ch)
 		tcf_chain_put_by_act(goto_ch);
+out_free_ex:
+	kfree(nparms->tcfp_keys_ex);
+out_free:
+	kfree(nparms);
 out_release:
 	tcf_idr_release(*a, bind);
-out_free:
-	kfree(keys_ex);
 	return ret;
-
 }
 
 static void tcf_pedit_cleanup(struct tc_action *a)
 {
 	struct tcf_pedit *p = to_pedit(a);
-	struct tc_pedit_key *keys = p->tcfp_keys;
+	struct tcf_pedit_parms *parms;
+
+	parms = rcu_dereference_protected(p->parms, 1);
 
-	kfree(keys);
-	kfree(p->tcfp_keys_ex);
+	if (parms)
+		call_rcu(&parms->rcu, tcf_pedit_cleanup_rcu);
 }
 
 static bool offset_valid(struct sk_buff *skb, int offset)
@@ -271,11 +317,35 @@
 	return true;
 }
 
-static int pedit_skb_hdr_offset(struct sk_buff *skb,
-				enum pedit_header_type htype, int *hoffset)
+static int pedit_l4_skb_offset(struct sk_buff *skb, int *hoffset, const int header_type)
 {
+	const int noff = skb_network_offset(skb);
 	int ret = -EINVAL;
+	struct iphdr _iph;
 
+	switch (skb->protocol) {
+	case htons(ETH_P_IP): {
+		const struct iphdr *iph = skb_header_pointer(skb, noff, sizeof(_iph), &_iph);
+
+		if (!iph)
+			goto out;
+		*hoffset = noff + iph->ihl * 4;
+		ret = 0;
+		break;
+	}
+	case htons(ETH_P_IPV6):
+		ret = ipv6_find_hdr(skb, hoffset, header_type, NULL, NULL) == header_type ? 0 : -EINVAL;
+		break;
+	}
+out:
+	return ret;
+}
+
+static int pedit_skb_hdr_offset(struct sk_buff *skb,
+				 enum pedit_header_type htype, int *hoffset)
+{
+	int ret = -EINVAL;
+	/* 'htype' is validated in the netlink parsing */
 	switch (htype) {
 	case TCA_PEDIT_KEY_EX_HDR_TYPE_ETH:
 		if (skb_mac_header_was_set(skb)) {
@@ -290,120 +360,120 @@
 		ret = 0;
 		break;
 	case TCA_PEDIT_KEY_EX_HDR_TYPE_TCP:
+		ret = pedit_l4_skb_offset(skb, hoffset, IPPROTO_TCP);
+		break;
 	case TCA_PEDIT_KEY_EX_HDR_TYPE_UDP:
-		if (skb_transport_header_was_set(skb)) {
-			*hoffset = skb_transport_offset(skb);
-			ret = 0;
-		}
+		ret = pedit_l4_skb_offset(skb, hoffset, IPPROTO_UDP);
 		break;
 	default:
-		ret = -EINVAL;
 		break;
 	}
-
 	return ret;
 }
 
 static int tcf_pedit_act(struct sk_buff *skb, const struct tc_action *a,
 			 struct tcf_result *res)
 {
+	enum pedit_header_type htype = TCA_PEDIT_KEY_EX_HDR_TYPE_NETWORK;
+	enum pedit_cmd cmd = TCA_PEDIT_KEY_EX_CMD_SET;
 	struct tcf_pedit *p = to_pedit(a);
+	struct tcf_pedit_key_ex *tkey_ex;
+	struct tcf_pedit_parms *parms;
+	struct tc_pedit_key *tkey;
+	u32 max_offset;
 	int i;
 
-	if (skb_unclone(skb, GFP_ATOMIC))
-		return p->tcf_action;
+	parms = rcu_dereference_bh(p->parms);
 
-	spin_lock(&p->tcf_lock);
+	max_offset = (skb_transport_header_was_set(skb) ?
+		      skb_transport_offset(skb) :
+		      skb_network_offset(skb)) +
+		     parms->tcfp_off_max_hint;
+	if (skb_ensure_writable(skb, min(skb->len, max_offset)))
+		goto done;
 
 	tcf_lastuse_update(&p->tcf_tm);
+	tcf_action_update_bstats(&p->common, skb);
 
-	if (p->tcfp_nkeys > 0) {
-		struct tc_pedit_key *tkey = p->tcfp_keys;
-		struct tcf_pedit_key_ex *tkey_ex = p->tcfp_keys_ex;
-		enum pedit_header_type htype =
-			TCA_PEDIT_KEY_EX_HDR_TYPE_NETWORK;
-		enum pedit_cmd cmd = TCA_PEDIT_KEY_EX_CMD_SET;
-
-		for (i = p->tcfp_nkeys; i > 0; i--, tkey++) {
-			u32 *ptr, hdata;
-			int offset = tkey->off;
-			int hoffset;
-			u32 val;
-			int rc;
-
-			if (tkey_ex) {
-				htype = tkey_ex->htype;
-				cmd = tkey_ex->cmd;
+	tkey = parms->tcfp_keys;
+	tkey_ex = parms->tcfp_keys_ex;
 
-				tkey_ex++;
-			}
+	for (i = parms->tcfp_nkeys; i > 0; i--, tkey++) {
+		int offset = tkey->off;
+		int hoffset = 0;
+		u32 *ptr, hdata;
+		u32 val;
+		int rc;
+
+		if (tkey_ex) {
+			htype = tkey_ex->htype;
+			cmd = tkey_ex->cmd;
 
-			rc = pedit_skb_hdr_offset(skb, htype, &hoffset);
-			if (rc) {
-				pr_info("tc action pedit bad header type specified (0x%x)\n",
-					htype);
-				goto bad;
-			}
+			tkey_ex++;
+		}
 
-			if (tkey->offmask) {
-				u8 *d, _d;
+		rc = pedit_skb_hdr_offset(skb, htype, &hoffset);
+		if (rc) {
+			pr_info_ratelimited("tc action pedit unable to extract header offset for header type (0x%x)\n", htype);
+			goto bad;
+		}
 
-				if (!offset_valid(skb, hoffset + tkey->at)) {
-					pr_info("tc action pedit 'at' offset %d out of bounds\n",
-						hoffset + tkey->at);
-					goto bad;
-				}
-				d = skb_header_pointer(skb, hoffset + tkey->at,
-						       sizeof(_d), &_d);
-				if (!d)
-					goto bad;
-				offset += (*d & tkey->offmask) >> tkey->shift;
-			}
+		if (tkey->offmask) {
+			u8 *d, _d;
 
-			if (offset % 4) {
-				pr_info("tc action pedit offset must be on 32 bit boundaries\n");
+			if (!offset_valid(skb, hoffset + tkey->at)) {
+				pr_info("tc action pedit 'at' offset %d out of bounds\n",
+					hoffset + tkey->at);
 				goto bad;
 			}
-
-			if (!offset_valid(skb, hoffset + offset)) {
-				pr_info("tc action pedit offset %d out of bounds\n",
-					hoffset + offset);
+			d = skb_header_pointer(skb, hoffset + tkey->at,
+					       sizeof(_d), &_d);
+			if (!d)
 				goto bad;
-			}
+			offset += (*d & tkey->offmask) >> tkey->shift;
+		}
 
-			ptr = skb_header_pointer(skb, hoffset + offset,
-						 sizeof(hdata), &hdata);
-			if (!ptr)
-				goto bad;
-			/* just do it, baby */
-			switch (cmd) {
-			case TCA_PEDIT_KEY_EX_CMD_SET:
-				val = tkey->val;
-				break;
-			case TCA_PEDIT_KEY_EX_CMD_ADD:
-				val = (*ptr + tkey->val) & ~tkey->mask;
-				break;
-			default:
-				pr_info("tc action pedit bad command (%d)\n",
-					cmd);
-				goto bad;
-			}
+		if (offset % 4) {
+			pr_info("tc action pedit offset must be on 32 bit boundaries\n");
+			goto bad;
+		}
 
-			*ptr = ((*ptr & tkey->mask) ^ val);
-			if (ptr == &hdata)
-				skb_store_bits(skb, hoffset + offset, ptr, 4);
+		if (!offset_valid(skb, hoffset + offset)) {
+			pr_info("tc action pedit offset %d out of bounds\n",
+				hoffset + offset);
+			goto bad;
 		}
 
-		goto done;
-	} else {
-		WARN(1, "pedit BUG: index %d\n", p->tcf_index);
+		ptr = skb_header_pointer(skb, hoffset + offset,
+					 sizeof(hdata), &hdata);
+		if (!ptr)
+			goto bad;
+		/* just do it, baby */
+		switch (cmd) {
+		case TCA_PEDIT_KEY_EX_CMD_SET:
+			val = tkey->val;
+			break;
+		case TCA_PEDIT_KEY_EX_CMD_ADD:
+			val = (*ptr + tkey->val) & ~tkey->mask;
+			break;
+		default:
+			pr_info("tc action pedit bad command (%d)\n",
+				cmd);
+			goto bad;
+		}
+
+		*ptr = ((*ptr & tkey->mask) ^ val);
+		if (ptr == &hdata)
+			skb_store_bits(skb, hoffset + offset, ptr, 4);
 	}
 
+	goto done;
+
 bad:
+	spin_lock(&p->tcf_lock);
 	p->tcf_qstats.overlimits++;
-done:
-	bstats_update(&p->tcf_bstats, skb);
 	spin_unlock(&p->tcf_lock);
+done:
 	return p->tcf_action;
 }
 
@@ -422,30 +492,33 @@
 {
 	unsigned char *b = skb_tail_pointer(skb);
 	struct tcf_pedit *p = to_pedit(a);
+	struct tcf_pedit_parms *parms;
 	struct tc_pedit *opt;
 	struct tcf_t t;
 	int s;
 
-	s = struct_size(opt, keys, p->tcfp_nkeys);
+	spin_lock_bh(&p->tcf_lock);
+	parms = rcu_dereference_protected(p->parms, 1);
+	s = struct_size(opt, keys, parms->tcfp_nkeys);
 
-	/* netlink spinlocks held above us - must use ATOMIC */
 	opt = kzalloc(s, GFP_ATOMIC);
-	if (unlikely(!opt))
+	if (unlikely(!opt)) {
+		spin_unlock_bh(&p->tcf_lock);
 		return -ENOBUFS;
+	}
 
-	spin_lock_bh(&p->tcf_lock);
-	memcpy(opt->keys, p->tcfp_keys, flex_array_size(opt, keys, p->tcfp_nkeys));
+	memcpy(opt->keys, parms->tcfp_keys,
+	       flex_array_size(opt, keys, parms->tcfp_nkeys));
 	opt->index = p->tcf_index;
-	opt->nkeys = p->tcfp_nkeys;
-	opt->flags = p->tcfp_flags;
+	opt->nkeys = parms->tcfp_nkeys;
+	opt->flags = parms->tcfp_flags;
 	opt->action = p->tcf_action;
 	opt->refcnt = refcount_read(&p->tcf_refcnt) - ref;
 	opt->bindcnt = atomic_read(&p->tcf_bindcnt) - bind;
 
-	if (p->tcfp_keys_ex) {
-		if (tcf_pedit_key_ex_dump(skb,
-					  p->tcfp_keys_ex,
-					  p->tcfp_nkeys))
+	if (parms->tcfp_keys_ex) {
+		if (tcf_pedit_key_ex_dump(skb, parms->tcfp_keys_ex,
+					  parms->tcfp_nkeys))
 			goto nla_put_failure;
 
 		if (nla_put(skb, TCA_PEDIT_PARMS_EX, s, opt))
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_police.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_police.c
@@ -90,7 +90,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, NULL, a,
-				     &act_police_ops, bind, true, 0);
+				     &act_police_ops, bind, true, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
@@ -239,6 +239,20 @@
 	return err;
 }
 
+static bool tcf_police_mtu_check(struct sk_buff *skb, u32 limit)
+{
+	u32 len;
+
+	if (skb_is_gso(skb))
+		return skb_gso_validate_mac_len(skb, limit);
+
+	len = qdisc_pkt_len(skb);
+	if (skb_at_tc_ingress(skb))
+		len += skb->mac_len;
+
+	return len <= limit;
+}
+
 static int tcf_police_act(struct sk_buff *skb, const struct tc_action *a,
 			  struct tcf_result *res)
 {
@@ -261,7 +275,7 @@
 			goto inc_overlimits;
 	}
 
-	if (qdisc_pkt_len(skb) <= p->tcfp_mtu) {
+	if (tcf_police_mtu_check(skb, p->tcfp_mtu)) {
 		if (!p->rate_present && !p->pps_present) {
 			ret = p->tcfp_result;
 			goto end;
@@ -352,23 +366,23 @@
 	opt.burst = PSCHED_NS2TICKS(p->tcfp_burst);
 	if (p->rate_present) {
 		psched_ratecfg_getrate(&opt.rate, &p->rate);
-		if ((police->params->rate.rate_bytes_ps >= (1ULL << 32)) &&
+		if ((p->rate.rate_bytes_ps >= (1ULL << 32)) &&
 		    nla_put_u64_64bit(skb, TCA_POLICE_RATE64,
-				      police->params->rate.rate_bytes_ps,
+				      p->rate.rate_bytes_ps,
 				      TCA_POLICE_PAD))
 			goto nla_put_failure;
 	}
 	if (p->peak_present) {
 		psched_ratecfg_getrate(&opt.peakrate, &p->peak);
-		if ((police->params->peak.rate_bytes_ps >= (1ULL << 32)) &&
+		if ((p->peak.rate_bytes_ps >= (1ULL << 32)) &&
 		    nla_put_u64_64bit(skb, TCA_POLICE_PEAKRATE64,
-				      police->params->peak.rate_bytes_ps,
+				      p->peak.rate_bytes_ps,
 				      TCA_POLICE_PAD))
 			goto nla_put_failure;
 	}
 	if (p->pps_present) {
 		if (nla_put_u64_64bit(skb, TCA_POLICE_PKTRATE64,
-				      police->params->ppsrate.rate_pkts_ps,
+				      p->ppsrate.rate_pkts_ps,
 				      TCA_POLICE_PAD))
 			goto nla_put_failure;
 		if (nla_put_u64_64bit(skb, TCA_POLICE_PKTBURST64,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_sample.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_sample.c
@@ -55,8 +55,8 @@
 					  sample_policy, NULL);
 	if (ret < 0)
 		return ret;
-	if (!tb[TCA_SAMPLE_PARMS] || !tb[TCA_SAMPLE_RATE] ||
-	    !tb[TCA_SAMPLE_PSAMPLE_GROUP])
+
+	if (!tb[TCA_SAMPLE_PARMS])
 		return -EINVAL;
 
 	parm = nla_data(tb[TCA_SAMPLE_PARMS]);
@@ -70,7 +70,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_sample_ops, bind, true, 0);
+				     &act_sample_ops, bind, true, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
@@ -80,6 +80,13 @@
 		tcf_idr_release(*a, bind);
 		return -EEXIST;
 	}
+
+	if (!tb[TCA_SAMPLE_RATE] || !tb[TCA_SAMPLE_PSAMPLE_GROUP]) {
+		NL_SET_ERR_MSG(extack, "sample rate and group are required");
+		err = -EINVAL;
+		goto release_idr;
+	}
+
 	err = tcf_action_check_ctrlact(parm->action, tp, &goto_ch, extack);
 	if (err < 0)
 		goto release_idr;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_simple.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_simple.c
@@ -128,7 +128,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_simp_ops, bind, false, 0);
+				     &act_simp_ops, bind, false, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_skbedit.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_skbedit.c
@@ -176,7 +176,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_skbedit_ops, bind, true, 0);
+				     &act_skbedit_ops, bind, true, act_flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_skbmod.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_skbmod.c
@@ -168,7 +168,7 @@
 
 	if (!exists) {
 		ret = tcf_idr_create(tn, index, est, a,
-				     &act_skbmod_ops, bind, true, 0);
+				     &act_skbmod_ops, bind, true, flags);
 		if (ret) {
 			tcf_idr_cleanup(tn, index);
 			return ret;
@@ -240,13 +240,13 @@
 	struct tcf_skbmod *d = to_skbmod(a);
 	unsigned char *b = skb_tail_pointer(skb);
 	struct tcf_skbmod_params  *p;
-	struct tc_skbmod opt = {
-		.index   = d->tcf_index,
-		.refcnt  = refcount_read(&d->tcf_refcnt) - ref,
-		.bindcnt = atomic_read(&d->tcf_bindcnt) - bind,
-	};
+	struct tc_skbmod opt;
 	struct tcf_t t;
 
+	memset(&opt, 0, sizeof(opt));
+	opt.index   = d->tcf_index;
+	opt.refcnt  = refcount_read(&d->tcf_refcnt) - ref,
+	opt.bindcnt = atomic_read(&d->tcf_bindcnt) - bind;
 	spin_lock_bh(&d->tcf_lock);
 	opt.action = d->tcf_action;
 	p = rcu_dereference_protected(d->skbmod_p,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/act_tunnel_key.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/act_tunnel_key.c
@@ -67,7 +67,7 @@
 	[TCA_TUNNEL_KEY_ENC_OPT_GENEVE_CLASS]	   = { .type = NLA_U16 },
 	[TCA_TUNNEL_KEY_ENC_OPT_GENEVE_TYPE]	   = { .type = NLA_U8 },
 	[TCA_TUNNEL_KEY_ENC_OPT_GENEVE_DATA]	   = { .type = NLA_BINARY,
-						       .len = 128 },
+						       .len = 127 },
 };
 
 static const struct nla_policy
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_api.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_api.c
@@ -41,8 +41,6 @@
 #include <net/tc_act/tc_gate.h>
 #include <net/flow_offload.h>
 
-extern const struct nla_policy rtm_tca_policy[TCA_MAX + 1];
-
 /* The list of all installed classifier types */
 static LIST_HEAD(tcf_proto_base);
 
@@ -535,8 +533,8 @@
 {
 	struct tcf_block *block = chain->block;
 	const struct tcf_proto_ops *tmplt_ops;
+	unsigned int refcnt, non_act_refcnt;
 	bool free_block = false;
-	unsigned int refcnt;
 	void *tmplt_priv;
 
 	mutex_lock(&block->lock);
@@ -556,13 +554,15 @@
 	 * save these to temporary variables.
 	 */
 	refcnt = --chain->refcnt;
+	non_act_refcnt = refcnt - chain->action_refcnt;
 	tmplt_ops = chain->tmplt_ops;
 	tmplt_priv = chain->tmplt_priv;
 
-	/* The last dropped non-action reference will trigger notification. */
-	if (refcnt - chain->action_refcnt == 0 && !by_act) {
-		tc_chain_notify_delete(tmplt_ops, tmplt_priv, chain->index,
-				       block, NULL, 0, 0, false);
+	if (non_act_refcnt == chain->explicitly_created && !by_act) {
+		if (non_act_refcnt == 0)
+			tc_chain_notify_delete(tmplt_ops, tmplt_priv,
+					       chain->index, block, NULL, 0, 0,
+					       false);
 		/* Last reference to chain, no need to lock. */
 		chain->flushing = false;
 	}
@@ -1044,7 +1044,7 @@
 
 	/* Find qdisc */
 	if (!*parent) {
-		*q = dev->qdisc;
+		*q = rcu_dereference(dev->qdisc);
 		*parent = (*q)->handle;
 	} else {
 		*q = qdisc_lookup_rcu(dev, TC_H_MAJ(*parent));
@@ -1412,6 +1412,9 @@
 	     chain_prev = chain,
 		     chain = __tcf_get_next_chain(block, chain),
 		     tcf_chain_put(chain_prev)) {
+		if (chain->tmplt_ops && add)
+			chain->tmplt_ops->tmplt_reoffload(chain, true, cb,
+							  cb_priv);
 		for (tp = __tcf_get_next_proto(chain, NULL); tp;
 		     tp_prev = tp,
 			     tp = __tcf_get_next_proto(chain, tp),
@@ -1427,6 +1430,9 @@
 				goto err_playback_remove;
 			}
 		}
+		if (chain->tmplt_ops && !add)
+			chain->tmplt_ops->tmplt_reoffload(chain, false, cb,
+							  cb_priv);
 	}
 
 	return 0;
@@ -1465,6 +1471,7 @@
 
 err_unroll:
 	list_for_each_entry_safe(block_cb, next, &bo->cb_list, list) {
+		list_del(&block_cb->driver_list);
 		if (i-- > 0) {
 			list_del(&block_cb->list);
 			tcf_block_playback_offloads(block, block_cb->cb,
@@ -1617,12 +1624,17 @@
 
 	/* If we missed on some chain */
 	if (ret == TC_ACT_UNSPEC && last_executed_chain) {
+		struct tc_skb_cb *cb = tc_skb_cb(skb);
+
 		ext = tc_skb_ext_alloc(skb);
 		if (WARN_ON_ONCE(!ext))
 			return TC_ACT_SHOT;
 		ext->chain = last_executed_chain;
-		ext->mru = qdisc_skb_cb(skb)->mru;
-		ext->post_ct = qdisc_skb_cb(skb)->post_ct;
+		ext->mru = cb->mru;
+		ext->post_ct = cb->post_ct;
+		ext->post_ct_snat = cb->post_ct_snat;
+		ext->post_ct_dnat = cb->post_ct_dnat;
+		ext->zone = cb->zone;
 	}
 
 	return ret;
@@ -1648,10 +1660,10 @@
 	if (chain->flushing)
 		return -EAGAIN;
 
+	RCU_INIT_POINTER(tp->next, tcf_chain_tp_prev(chain, chain_info));
 	if (*chain_info->pprev == chain->filter_chain)
 		tcf_chain0_head_change(chain, tp);
 	tcf_proto_get(tp);
-	RCU_INIT_POINTER(tp->next, tcf_chain_tp_prev(chain, chain_info));
 	rcu_assign_pointer(*chain_info->pprev, tp);
 
 	return 0;
@@ -1940,9 +1952,9 @@
 	bool prio_allocate;
 	u32 parent;
 	u32 chain_index;
-	struct Qdisc *q = NULL;
+	struct Qdisc *q;
 	struct tcf_chain_info chain_info;
-	struct tcf_chain *chain = NULL;
+	struct tcf_chain *chain;
 	struct tcf_block *block;
 	struct tcf_proto *tp;
 	unsigned long cl;
@@ -1971,6 +1983,8 @@
 	tp = NULL;
 	cl = 0;
 	block = NULL;
+	q = NULL;
+	chain = NULL;
 	flags = 0;
 
 	if (prio == 0) {
@@ -2110,6 +2124,7 @@
 	}
 
 	if (chain->tmplt_ops && chain->tmplt_ops != tp->ops) {
+		tfilter_put(tp, fh);
 		NL_SET_ERR_MSG(extack, "Chain template is set to a different filter kind");
 		err = -EINVAL;
 		goto errout;
@@ -2580,7 +2595,7 @@
 
 		parent = tcm->tcm_parent;
 		if (!parent)
-			q = dev->qdisc;
+			q = rtnl_dereference(dev->qdisc);
 		else
 			q = qdisc_lookup(dev, TC_H_MAJ(tcm->tcm_parent));
 		if (!q)
@@ -2757,8 +2772,10 @@
 	ops = tcf_proto_lookup_ops(name, true, extack);
 	if (IS_ERR(ops))
 		return PTR_ERR(ops);
-	if (!ops->tmplt_create || !ops->tmplt_destroy || !ops->tmplt_dump) {
+	if (!ops->tmplt_create || !ops->tmplt_destroy || !ops->tmplt_dump ||
+	    !ops->tmplt_reoffload) {
 		NL_SET_ERR_MSG(extack, "Chain templates are not supported with specified classifier");
+		module_put(ops->owner);
 		return -EOPNOTSUPP;
 	}
 
@@ -2793,8 +2810,8 @@
 	struct tcmsg *t;
 	u32 parent;
 	u32 chain_index;
-	struct Qdisc *q = NULL;
-	struct tcf_chain *chain = NULL;
+	struct Qdisc *q;
+	struct tcf_chain *chain;
 	struct tcf_block *block;
 	unsigned long cl;
 	int err;
@@ -2804,6 +2821,7 @@
 		return -EPERM;
 
 replay:
+	q = NULL;
 	err = nlmsg_parse_deprecated(n, sizeof(*t), tca, TCA_MAX,
 				     rtm_tca_policy, extack);
 	if (err < 0)
@@ -2954,7 +2972,7 @@
 			return skb->len;
 
 		if (!tcm->tcm_parent)
-			q = dev->qdisc;
+			q = rtnl_dereference(dev->qdisc);
 		else
 			q = qdisc_lookup(dev, TC_H_MAJ(tcm->tcm_parent));
 
@@ -3687,6 +3705,7 @@
 				entry->mpls_mangle.ttl = tcf_mpls_ttl(act);
 				break;
 			default:
+				err = -EOPNOTSUPP;
 				goto err_out_locked;
 			}
 		} else if (is_tcf_skbedit_ptype(act)) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_bpf.c
@@ -402,56 +402,6 @@
 	return 0;
 }
 
-static int cls_bpf_set_parms(struct net *net, struct tcf_proto *tp,
-			     struct cls_bpf_prog *prog, unsigned long base,
-			     struct nlattr **tb, struct nlattr *est, u32 flags,
-			     struct netlink_ext_ack *extack)
-{
-	bool is_bpf, is_ebpf, have_exts = false;
-	u32 gen_flags = 0;
-	int ret;
-
-	is_bpf = tb[TCA_BPF_OPS_LEN] && tb[TCA_BPF_OPS];
-	is_ebpf = tb[TCA_BPF_FD];
-	if ((!is_bpf && !is_ebpf) || (is_bpf && is_ebpf))
-		return -EINVAL;
-
-	ret = tcf_exts_validate(net, tp, tb, est, &prog->exts, flags,
-				extack);
-	if (ret < 0)
-		return ret;
-
-	if (tb[TCA_BPF_FLAGS]) {
-		u32 bpf_flags = nla_get_u32(tb[TCA_BPF_FLAGS]);
-
-		if (bpf_flags & ~TCA_BPF_FLAG_ACT_DIRECT)
-			return -EINVAL;
-
-		have_exts = bpf_flags & TCA_BPF_FLAG_ACT_DIRECT;
-	}
-	if (tb[TCA_BPF_FLAGS_GEN]) {
-		gen_flags = nla_get_u32(tb[TCA_BPF_FLAGS_GEN]);
-		if (gen_flags & ~CLS_BPF_SUPPORTED_GEN_FLAGS ||
-		    !tc_flags_valid(gen_flags))
-			return -EINVAL;
-	}
-
-	prog->exts_integrated = have_exts;
-	prog->gen_flags = gen_flags;
-
-	ret = is_bpf ? cls_bpf_prog_from_ops(tb, prog) :
-		       cls_bpf_prog_from_efd(tb, prog, gen_flags, tp);
-	if (ret < 0)
-		return ret;
-
-	if (tb[TCA_BPF_CLASSID]) {
-		prog->res.classid = nla_get_u32(tb[TCA_BPF_CLASSID]);
-		tcf_bind_filter(tp, &prog->res, base);
-	}
-
-	return 0;
-}
-
 static int cls_bpf_change(struct net *net, struct sk_buff *in_skb,
 			  struct tcf_proto *tp, unsigned long base,
 			  u32 handle, struct nlattr **tca,
@@ -459,9 +409,12 @@
 			  struct netlink_ext_ack *extack)
 {
 	struct cls_bpf_head *head = rtnl_dereference(tp->root);
+	bool is_bpf, is_ebpf, have_exts = false;
 	struct cls_bpf_prog *oldprog = *arg;
 	struct nlattr *tb[TCA_BPF_MAX + 1];
+	bool bound_to_filter = false;
 	struct cls_bpf_prog *prog;
+	u32 gen_flags = 0;
 	int ret;
 
 	if (tca[TCA_OPTIONS] == NULL)
@@ -500,11 +453,51 @@
 		goto errout;
 	prog->handle = handle;
 
-	ret = cls_bpf_set_parms(net, tp, prog, base, tb, tca[TCA_RATE], flags,
-				extack);
+	is_bpf = tb[TCA_BPF_OPS_LEN] && tb[TCA_BPF_OPS];
+	is_ebpf = tb[TCA_BPF_FD];
+	if ((!is_bpf && !is_ebpf) || (is_bpf && is_ebpf)) {
+		ret = -EINVAL;
+		goto errout_idr;
+	}
+
+	ret = tcf_exts_validate(net, tp, tb, tca[TCA_RATE], &prog->exts,
+				flags, extack);
+	if (ret < 0)
+		goto errout_idr;
+
+	if (tb[TCA_BPF_FLAGS]) {
+		u32 bpf_flags = nla_get_u32(tb[TCA_BPF_FLAGS]);
+
+		if (bpf_flags & ~TCA_BPF_FLAG_ACT_DIRECT) {
+			ret = -EINVAL;
+			goto errout_idr;
+		}
+
+		have_exts = bpf_flags & TCA_BPF_FLAG_ACT_DIRECT;
+	}
+	if (tb[TCA_BPF_FLAGS_GEN]) {
+		gen_flags = nla_get_u32(tb[TCA_BPF_FLAGS_GEN]);
+		if (gen_flags & ~CLS_BPF_SUPPORTED_GEN_FLAGS ||
+		    !tc_flags_valid(gen_flags)) {
+			ret = -EINVAL;
+			goto errout_idr;
+		}
+	}
+
+	prog->exts_integrated = have_exts;
+	prog->gen_flags = gen_flags;
+
+	ret = is_bpf ? cls_bpf_prog_from_ops(tb, prog) :
+		cls_bpf_prog_from_efd(tb, prog, gen_flags, tp);
 	if (ret < 0)
 		goto errout_idr;
 
+	if (tb[TCA_BPF_CLASSID]) {
+		prog->res.classid = nla_get_u32(tb[TCA_BPF_CLASSID]);
+		tcf_bind_filter(tp, &prog->res, base);
+		bound_to_filter = true;
+	}
+
 	ret = cls_bpf_offload(tp, prog, oldprog, extack);
 	if (ret)
 		goto errout_parms;
@@ -526,6 +519,8 @@
 	return 0;
 
 errout_parms:
+	if (bound_to_filter)
+		tcf_unbind_filter(tp, &prog->res);
 	cls_bpf_free_parms(prog);
 errout_idr:
 	if (!oldprog)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_flow.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_flow.c
@@ -354,7 +354,8 @@
 	[TCA_FLOW_KEYS]		= { .type = NLA_U32 },
 	[TCA_FLOW_MODE]		= { .type = NLA_U32 },
 	[TCA_FLOW_BASECLASS]	= { .type = NLA_U32 },
-	[TCA_FLOW_RSHIFT]	= { .type = NLA_U32 },
+	[TCA_FLOW_RSHIFT]	= NLA_POLICY_MAX(NLA_U32,
+						 31 /* BITS_PER_U32 - 1 */),
 	[TCA_FLOW_ADDEND]	= { .type = NLA_U32 },
 	[TCA_FLOW_MASK]		= { .type = NLA_U32 },
 	[TCA_FLOW_XOR]		= { .type = NLA_U32 },
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_flower.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_flower.c
@@ -19,6 +19,7 @@
 
 #include <net/sch_generic.h>
 #include <net/pkt_cls.h>
+#include <net/pkt_sched.h>
 #include <net/ip.h>
 #include <net/flow_dissector.h>
 #include <net/geneve.h>
@@ -61,13 +62,7 @@
 	struct flow_dissector_key_ip ip;
 	struct flow_dissector_key_ip enc_ip;
 	struct flow_dissector_key_enc_opts enc_opts;
-	union {
-		struct flow_dissector_key_ports tp;
-		struct {
-			struct flow_dissector_key_ports tp_min;
-			struct flow_dissector_key_ports tp_max;
-		};
-	} tp_range;
+	struct flow_dissector_key_ports_range tp_range;
 	struct flow_dissector_key_ct ct;
 	struct flow_dissector_key_hash hash;
 } __aligned(BITS_PER_LONG / 8); /* Ensure that we can do comparisons as longs. */
@@ -309,7 +304,8 @@
 		       struct tcf_result *res)
 {
 	struct cls_fl_head *head = rcu_dereference_bh(tp->root);
-	bool post_ct = qdisc_skb_cb(skb)->post_ct;
+	bool post_ct = tc_skb_cb(skb)->post_ct;
+	u16 zone = tc_skb_cb(skb)->zone;
 	struct fl_flow_key skb_key;
 	struct fl_flow_mask *mask;
 	struct cls_fl_filter *f;
@@ -327,7 +323,7 @@
 		skb_flow_dissect_ct(skb, &mask->dissector, &skb_key,
 				    fl_ct_info_to_flower_map,
 				    ARRAY_SIZE(fl_ct_info_to_flower_map),
-				    post_ct);
+				    post_ct, zone);
 		skb_flow_dissect_hash(skb, &mask->dissector, &skb_key);
 		skb_flow_dissect(skb, &mask->dissector, &skb_key, 0);
 
@@ -727,7 +723,7 @@
 	[TCA_FLOWER_KEY_ENC_OPT_GENEVE_CLASS]      = { .type = NLA_U16 },
 	[TCA_FLOWER_KEY_ENC_OPT_GENEVE_TYPE]       = { .type = NLA_U8 },
 	[TCA_FLOWER_KEY_ENC_OPT_GENEVE_DATA]       = { .type = NLA_BINARY,
-						       .len = 128 },
+						       .len = 127 },
 };
 
 static const struct nla_policy
@@ -782,6 +778,16 @@
 		       TCA_FLOWER_KEY_PORT_SRC_MAX, &mask->tp_range.tp_max.src,
 		       TCA_FLOWER_UNSPEC, sizeof(key->tp_range.tp_max.src));
 
+	if (mask->tp_range.tp_min.dst != mask->tp_range.tp_max.dst) {
+		NL_SET_ERR_MSG(extack,
+			       "Both min and max destination ports must be specified");
+		return -EINVAL;
+	}
+	if (mask->tp_range.tp_min.src != mask->tp_range.tp_max.src) {
+		NL_SET_ERR_MSG(extack,
+			       "Both min and max source ports must be specified");
+		return -EINVAL;
+	}
 	if (mask->tp_range.tp_min.dst && mask->tp_range.tp_max.dst &&
 	    ntohs(key->tp_range.tp_max.dst) <=
 	    ntohs(key->tp_range.tp_min.dst)) {
@@ -1002,6 +1008,7 @@
 static void fl_set_key_vlan(struct nlattr **tb,
 			    __be16 ethertype,
 			    int vlan_id_key, int vlan_prio_key,
+			    int vlan_next_eth_type_key,
 			    struct flow_dissector_key_vlan *key_val,
 			    struct flow_dissector_key_vlan *key_mask)
 {
@@ -1020,6 +1027,11 @@
 	}
 	key_val->vlan_tpid = ethertype;
 	key_mask->vlan_tpid = cpu_to_be16(~0);
+	if (tb[vlan_next_eth_type_key]) {
+		key_val->vlan_eth_type =
+			nla_get_be16(tb[vlan_next_eth_type_key]);
+		key_mask->vlan_eth_type = cpu_to_be16(~0);
+	}
 }
 
 static void fl_set_key_flag(u32 flower_key, u32 flower_mask,
@@ -1084,6 +1096,9 @@
 	if (option_len > sizeof(struct geneve_opt))
 		data_len = option_len - sizeof(struct geneve_opt);
 
+	if (key->enc_opts.len > FLOW_DIS_TUN_OPTS_MAX - 4)
+		return -ERANGE;
+
 	opt = (struct geneve_opt *)&key->enc_opts.data[key->enc_opts.len];
 	memset(opt, 0xff, option_len);
 	opt->length = data_len / 4;
@@ -1203,7 +1218,6 @@
 	int err;
 
 	md = (struct erspan_metadata *)&key->enc_opts.data[key->enc_opts.len];
-	memset(md, 0xff, sizeof(*md));
 	md->version = 1;
 
 	if (!depth)
@@ -1232,9 +1246,9 @@
 			NL_SET_ERR_MSG(extack, "Missing tunnel key erspan option index");
 			return -EINVAL;
 		}
+		memset(&md->u.index, 0xff, sizeof(md->u.index));
 		if (tb[TCA_FLOWER_KEY_ENC_OPT_ERSPAN_INDEX]) {
 			nla = tb[TCA_FLOWER_KEY_ENC_OPT_ERSPAN_INDEX];
-			memset(&md->u, 0x00, sizeof(md->u));
 			md->u.index = nla_get_be32(nla);
 		}
 	} else if (md->version == 2) {
@@ -1243,10 +1257,12 @@
 			NL_SET_ERR_MSG(extack, "Missing tunnel key erspan option dir or hwid");
 			return -EINVAL;
 		}
+		md->u.md2.dir = 1;
 		if (tb[TCA_FLOWER_KEY_ENC_OPT_ERSPAN_DIR]) {
 			nla = tb[TCA_FLOWER_KEY_ENC_OPT_ERSPAN_DIR];
 			md->u.md2.dir = nla_get_u8(nla);
 		}
+		set_hwid(&md->u.md2, 0xff);
 		if (tb[TCA_FLOWER_KEY_ENC_OPT_ERSPAN_HWID]) {
 			nla = tb[TCA_FLOWER_KEY_ENC_OPT_ERSPAN_HWID];
 			set_hwid(&md->u.md2, nla_get_u8(nla));
@@ -1516,8 +1532,9 @@
 
 		if (eth_type_vlan(ethertype)) {
 			fl_set_key_vlan(tb, ethertype, TCA_FLOWER_KEY_VLAN_ID,
-					TCA_FLOWER_KEY_VLAN_PRIO, &key->vlan,
-					&mask->vlan);
+					TCA_FLOWER_KEY_VLAN_PRIO,
+					TCA_FLOWER_KEY_VLAN_ETH_TYPE,
+					&key->vlan, &mask->vlan);
 
 			if (tb[TCA_FLOWER_KEY_VLAN_ETH_TYPE]) {
 				ethertype = nla_get_be16(tb[TCA_FLOWER_KEY_VLAN_ETH_TYPE]);
@@ -1525,6 +1542,7 @@
 					fl_set_key_vlan(tb, ethertype,
 							TCA_FLOWER_KEY_CVLAN_ID,
 							TCA_FLOWER_KEY_CVLAN_PRIO,
+							TCA_FLOWER_KEY_CVLAN_ETH_TYPE,
 							&key->cvlan, &mask->cvlan);
 					fl_set_key_val(tb, &key->basic.n_proto,
 						       TCA_FLOWER_KEY_CVLAN_ETH_TYPE,
@@ -2412,6 +2430,28 @@
 	kfree(tmplt);
 }
 
+static void fl_tmplt_reoffload(struct tcf_chain *chain, bool add,
+			       flow_setup_cb_t *cb, void *cb_priv)
+{
+	struct fl_flow_tmplt *tmplt = chain->tmplt_priv;
+	struct flow_cls_offload cls_flower = {};
+
+	cls_flower.rule = flow_rule_alloc(0);
+	if (!cls_flower.rule)
+		return;
+
+	cls_flower.common.chain_index = chain->index;
+	cls_flower.command = add ? FLOW_CLS_TMPLT_CREATE :
+				   FLOW_CLS_TMPLT_DESTROY;
+	cls_flower.cookie = (unsigned long) tmplt;
+	cls_flower.rule->match.dissector = &tmplt->dissector;
+	cls_flower.rule->match.mask = &tmplt->mask;
+	cls_flower.rule->match.key = &tmplt->dummy_key;
+
+	cb(TC_SETUP_CLSFLOWER, &cls_flower, cb_priv);
+	kfree(cls_flower.rule);
+}
+
 static int fl_dump_key_val(struct sk_buff *skb,
 			   void *val, int val_type,
 			   void *mask, int mask_type, int len)
@@ -2880,13 +2920,13 @@
 		goto nla_put_failure;
 
 	if (mask->basic.n_proto) {
-		if (mask->cvlan.vlan_tpid) {
+		if (mask->cvlan.vlan_eth_type) {
 			if (nla_put_be16(skb, TCA_FLOWER_KEY_CVLAN_ETH_TYPE,
 					 key->basic.n_proto))
 				goto nla_put_failure;
-		} else if (mask->vlan.vlan_tpid) {
+		} else if (mask->vlan.vlan_eth_type) {
 			if (nla_put_be16(skb, TCA_FLOWER_KEY_VLAN_ETH_TYPE,
-					 key->basic.n_proto))
+					 key->vlan.vlan_eth_type))
 				goto nla_put_failure;
 		}
 	}
@@ -3217,6 +3257,7 @@
 	.bind_class	= fl_bind_class,
 	.tmplt_create	= fl_tmplt_create,
 	.tmplt_destroy	= fl_tmplt_destroy,
+	.tmplt_reoffload = fl_tmplt_reoffload,
 	.tmplt_dump	= fl_tmplt_dump,
 	.owner		= THIS_MODULE,
 	.flags		= TCF_PROTO_OPS_DOIT_UNLOCKED,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_fw.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_fw.c
@@ -210,11 +210,6 @@
 	if (err < 0)
 		return err;
 
-	if (tb[TCA_FW_CLASSID]) {
-		f->res.classid = nla_get_u32(tb[TCA_FW_CLASSID]);
-		tcf_bind_filter(tp, &f->res, base);
-	}
-
 	if (tb[TCA_FW_INDEV]) {
 		int ret;
 		ret = tcf_change_indev(net, tb[TCA_FW_INDEV], extack);
@@ -231,6 +226,11 @@
 	} else if (head->mask != 0xFFFFFFFF)
 		return err;
 
+	if (tb[TCA_FW_CLASSID]) {
+		f->res.classid = nla_get_u32(tb[TCA_FW_CLASSID]);
+		tcf_bind_filter(tp, &f->res, base);
+	}
+
 	return 0;
 }
 
@@ -265,7 +265,6 @@
 			return -ENOBUFS;
 
 		fnew->id = f->id;
-		fnew->res = f->res;
 		fnew->ifindex = f->ifindex;
 		fnew->tp = f->tp;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_route.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_route.c
@@ -424,6 +424,11 @@
 			return -EINVAL;
 	}
 
+	if (!nhandle) {
+		NL_SET_ERR_MSG(extack, "Replacing with handle of 0 is invalid");
+		return -EINVAL;
+	}
+
 	h1 = to_hash(nhandle);
 	b = rtnl_dereference(head->table[h1]);
 	if (!b) {
@@ -477,6 +482,11 @@
 	int err;
 	bool new = true;
 
+	if (!handle) {
+		NL_SET_ERR_MSG(extack, "Creating with handle of 0 is invalid");
+		return -EINVAL;
+	}
+
 	if (opt == NULL)
 		return handle ? -EINVAL : 0;
 
@@ -501,7 +511,6 @@
 	if (fold) {
 		f->id = fold->id;
 		f->iif = fold->iif;
-		f->res = fold->res;
 		f->handle = fold->handle;
 
 		f->tp = fold->tp;
@@ -526,7 +535,7 @@
 	rcu_assign_pointer(f->next, f1);
 	rcu_assign_pointer(*fp, f);
 
-	if (fold && fold->handle && f->handle != fold->handle) {
+	if (fold) {
 		th = to_hash(fold->handle);
 		h = from_hash(fold->handle >> 16);
 		b = rtnl_dereference(head->table[th]);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/cls_u32.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/cls_u32.c
@@ -364,7 +364,7 @@
 	idr_init(&root_ht->handle_idr);
 
 	if (tp_c == NULL) {
-		tp_c = kzalloc(struct_size(tp_c, hlist->ht, 1), GFP_KERNEL);
+		tp_c = kzalloc(sizeof(*tp_c), GFP_KERNEL);
 		if (tp_c == NULL) {
 			kfree(root_ht);
 			return -ENOBUFS;
@@ -386,14 +386,19 @@
 	return 0;
 }
 
-static int u32_destroy_key(struct tc_u_knode *n, bool free_pf)
+static void __u32_destroy_key(struct tc_u_knode *n)
 {
 	struct tc_u_hnode *ht = rtnl_dereference(n->ht_down);
 
 	tcf_exts_destroy(&n->exts);
-	tcf_exts_put_net(&n->exts);
 	if (ht && --ht->refcnt == 0)
 		kfree(ht);
+	kfree(n);
+}
+
+static void u32_destroy_key(struct tc_u_knode *n, bool free_pf)
+{
+	tcf_exts_put_net(&n->exts);
 #ifdef CONFIG_CLS_U32_PERF
 	if (free_pf)
 		free_percpu(n->pf);
@@ -402,8 +407,7 @@
 	if (free_pf)
 		free_percpu(n->pcpu_success);
 #endif
-	kfree(n);
-	return 0;
+	__u32_destroy_key(n);
 }
 
 /* u32_delete_key_rcu should be called when free'ing a copied
@@ -712,12 +716,18 @@
 			 struct nlattr *est, u32 flags,
 			 struct netlink_ext_ack *extack)
 {
-	int err;
+	int err, ifindex = -1;
 
 	err = tcf_exts_validate(net, tp, tb, est, &n->exts, flags, extack);
 	if (err < 0)
 		return err;
 
+	if (tb[TCA_U32_INDEV]) {
+		ifindex = tcf_change_indev(net, tb[TCA_U32_INDEV], extack);
+		if (ifindex < 0)
+			return -EINVAL;
+	}
+
 	if (tb[TCA_U32_LINK]) {
 		u32 handle = nla_get_u32(tb[TCA_U32_LINK]);
 		struct tc_u_hnode *ht_down = NULL, *ht_old;
@@ -752,13 +762,9 @@
 		tcf_bind_filter(tp, &n->res, base);
 	}
 
-	if (tb[TCA_U32_INDEV]) {
-		int ret;
-		ret = tcf_change_indev(net, tb[TCA_U32_INDEV], extack);
-		if (ret < 0)
-			return -EINVAL;
-		n->ifindex = ret;
-	}
+	if (ifindex >= 0)
+		n->ifindex = ifindex;
+
 	return 0;
 }
 
@@ -806,14 +812,9 @@
 
 	new->ifindex = n->ifindex;
 	new->fshift = n->fshift;
-	new->res = n->res;
 	new->flags = n->flags;
 	RCU_INIT_POINTER(new->ht_down, ht);
 
-	/* bump reference count as long as we hold pointer to structure */
-	if (ht)
-		ht->refcnt++;
-
 #ifdef CONFIG_CLS_U32_PERF
 	/* Statistics may be incremented by readers during update
 	 * so we must keep them in tact. When the node is later destroyed
@@ -835,6 +836,10 @@
 		return NULL;
 	}
 
+	/* bump reference count as long as we hold pointer to structure */
+	if (ht)
+		ht->refcnt++;
+
 	return new;
 }
 
@@ -898,13 +903,13 @@
 				    tca[TCA_RATE], flags, extack);
 
 		if (err) {
-			u32_destroy_key(new, false);
+			__u32_destroy_key(new);
 			return err;
 		}
 
 		err = u32_replace_hw_knode(tp, new, flags, extack);
 		if (err) {
-			u32_destroy_key(new, false);
+			__u32_destroy_key(new);
 			return err;
 		}
 
@@ -993,18 +998,62 @@
 		return -EINVAL;
 	}
 
+	/* At this point, we need to derive the new handle that will be used to
+	 * uniquely map the identity of this table match entry. The
+	 * identity of the entry that we need to construct is 32 bits made of:
+	 *     htid(12b):bucketid(8b):node/entryid(12b)
+	 *
+	 * At this point _we have the table(ht)_ in which we will insert this
+	 * entry. We carry the table's id in variable "htid".
+	 * Note that earlier code picked the ht selection either by a) the user
+	 * providing the htid specified via TCA_U32_HASH attribute or b) when
+	 * no such attribute is passed then the root ht, is default to at ID
+	 * 0x[800][00][000]. Rule: the root table has a single bucket with ID 0.
+	 * If OTOH the user passed us the htid, they may also pass a bucketid of
+	 * choice. 0 is fine. For example a user htid is 0x[600][01][000] it is
+	 * indicating hash bucketid of 1. Rule: the entry/node ID _cannot_ be
+	 * passed via the htid, so even if it was non-zero it will be ignored.
+	 *
+	 * We may also have a handle, if the user passed one. The handle also
+	 * carries the same addressing of htid(12b):bucketid(8b):node/entryid(12b).
+	 * Rule: the bucketid on the handle is ignored even if one was passed;
+	 * rather the value on "htid" is always assumed to be the bucketid.
+	 */
 	if (handle) {
+		/* Rule: The htid from handle and tableid from htid must match */
 		if (TC_U32_HTID(handle) && TC_U32_HTID(handle ^ htid)) {
 			NL_SET_ERR_MSG_MOD(extack, "Handle specified hash table address mismatch");
 			return -EINVAL;
 		}
-		handle = htid | TC_U32_NODE(handle);
-		err = idr_alloc_u32(&ht->handle_idr, NULL, &handle, handle,
-				    GFP_KERNEL);
-		if (err)
-			return err;
-	} else
+		/* Ok, so far we have a valid htid(12b):bucketid(8b) but we
+		 * need to finalize the table entry identification with the last
+		 * part - the node/entryid(12b)). Rule: Nodeid _cannot be 0_ for
+		 * entries. Rule: nodeid of 0 is reserved only for tables(see
+		 * earlier code which processes TC_U32_DIVISOR attribute).
+		 * Rule: The nodeid can only be derived from the handle (and not
+		 * htid).
+		 * Rule: if the handle specified zero for the node id example
+		 * 0x60000000, then pick a new nodeid from the pool of IDs
+		 * this hash table has been allocating from.
+		 * If OTOH it is specified (i.e for example the user passed a
+		 * handle such as 0x60000123), then we use it generate our final
+		 * handle which is used to uniquely identify the match entry.
+		 */
+		if (!TC_U32_NODE(handle)) {
+			handle = gen_new_kid(ht, htid);
+		} else {
+			handle = htid | TC_U32_NODE(handle);
+			err = idr_alloc_u32(&ht->handle_idr, NULL, &handle,
+					    handle, GFP_KERNEL);
+			if (err)
+				return err;
+		}
+	} else {
+		/* The user did not give us a handle; lets just generate one
+		 * from the table's pool of nodeids.
+		 */
 		handle = gen_new_kid(ht, htid);
+	}
 
 	if (tb[TCA_U32_SEL] == NULL) {
 		NL_SET_ERR_MSG_MOD(extack, "Selector not specified");
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/em_text.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/em_text.c
@@ -97,8 +97,10 @@
 
 static void em_text_destroy(struct tcf_ematch *m)
 {
-	if (EM_TEXT_PRIV(m) && EM_TEXT_PRIV(m)->config)
+	if (EM_TEXT_PRIV(m) && EM_TEXT_PRIV(m)->config) {
 		textsearch_destroy(EM_TEXT_PRIV(m)->config);
+		kfree(EM_TEXT_PRIV(m));
+	}
 }
 
 static int em_text_dump(struct sk_buff *skb, struct tcf_ematch *m)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/ematch.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/ematch.c
@@ -255,6 +255,8 @@
 			 * the value carried.
 			 */
 			if (em_hdr->flags & TCF_EM_SIMPLE) {
+				if (em->ops->datalen > 0)
+					goto errout;
 				if (data_len < sizeof(u32))
 					goto errout;
 				em->data = *(u32 *) data;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_api.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_api.c
@@ -301,7 +301,7 @@
 
 	if (!handle)
 		return NULL;
-	q = qdisc_match_from_root(dev->qdisc, handle);
+	q = qdisc_match_from_root(rtnl_dereference(dev->qdisc), handle);
 	if (q)
 		goto out;
 
@@ -320,7 +320,7 @@
 
 	if (!handle)
 		return NULL;
-	q = qdisc_match_from_root(dev->qdisc, handle);
+	q = qdisc_match_from_root(rcu_dereference(dev->qdisc), handle);
 	if (q)
 		goto out;
 
@@ -589,7 +589,6 @@
 		pkt_len = 1;
 	qdisc_skb_cb(skb)->pkt_len = pkt_len;
 }
-EXPORT_SYMBOL(__qdisc_calculate_pkt_len);
 
 void qdisc_warn_nonwc(const char *txt, struct Qdisc *qdisc)
 {
@@ -781,7 +780,7 @@
 	drops = max_t(int, n, 0);
 	rcu_read_lock();
 	while ((parentid = sch->parent)) {
-		if (TC_H_MAJ(parentid) == TC_H_MAJ(TC_H_INGRESS))
+		if (parentid == TC_H_ROOT)
 			break;
 
 		if (sch->flags & TCQ_F_NOPARENT)
@@ -1044,12 +1043,12 @@
 
 	if (parent == NULL) {
 		unsigned int i, num_q, ingress;
+		struct netdev_queue *dev_queue;
 
 		ingress = 0;
 		num_q = dev->num_tx_queues;
 		if ((q && q->flags & TCQ_F_INGRESS) ||
 		    (new && new->flags & TCQ_F_INGRESS)) {
-			num_q = 1;
 			ingress = 1;
 			if (!dev_ingress_queue(dev)) {
 				NL_SET_ERR_MSG(extack, "Device does not have an ingress queue");
@@ -1062,30 +1061,31 @@
 
 		qdisc_offload_graft_root(dev, new, old, extack);
 
-		if (new && new->ops->attach)
+		if (new && new->ops->attach && !ingress)
 			goto skip;
 
-		for (i = 0; i < num_q; i++) {
-			struct netdev_queue *dev_queue = dev_ingress_queue(dev);
-
-			if (!ingress)
+		if (!ingress) {
+			for (i = 0; i < num_q; i++) {
 				dev_queue = netdev_get_tx_queue(dev, i);
+				old = dev_graft_qdisc(dev_queue, new);
 
-			old = dev_graft_qdisc(dev_queue, new);
-			if (new && i > 0)
-				qdisc_refcount_inc(new);
-
-			if (!ingress)
+				if (new && i > 0)
+					qdisc_refcount_inc(new);
 				qdisc_put(old);
+			}
+		} else {
+			dev_queue = dev_ingress_queue(dev);
+			old = dev_graft_qdisc(dev_queue, new);
 		}
 
 skip:
 		if (!ingress) {
-			notify_and_destroy(net, skb, n, classid,
-					   dev->qdisc, new);
+			old = rtnl_dereference(dev->qdisc);
 			if (new && !new->ops->attach)
 				qdisc_refcount_inc(new);
-			dev->qdisc = new ? : &noop_qdisc;
+			rcu_assign_pointer(dev->qdisc, new ? : &noop_qdisc);
+
+			notify_and_destroy(net, skb, n, classid, old, new);
 
 			if (new && new->ops->attach)
 				new->ops->attach(new);
@@ -1113,6 +1113,17 @@
 			return -ENOENT;
 		}
 
+		if (new && new->ops == &noqueue_qdisc_ops) {
+			NL_SET_ERR_MSG(extack, "Cannot assign noqueue to a class");
+			return -EINVAL;
+		}
+
+		if (new &&
+		    !(parent->flags & TCQ_F_MQROOT) &&
+		    rcu_access_pointer(new->stab)) {
+			NL_SET_ERR_MSG(extack, "STAB not supported on a non root");
+			return -EINVAL;
+		}
 		err = cops->graft(parent, cl, new, &old, extack);
 		if (err)
 			return err;
@@ -1204,7 +1215,7 @@
 
 	err = -ENOENT;
 	if (!ops) {
-		NL_SET_ERR_MSG(extack, "Specified qdisc not found");
+		NL_SET_ERR_MSG(extack, "Specified qdisc kind is unknown");
 		goto err_out;
 	}
 
@@ -1217,7 +1228,12 @@
 	sch->parent = parent;
 
 	if (handle == TC_H_INGRESS) {
-		sch->flags |= TCQ_F_INGRESS;
+		if (!(sch->flags & TCQ_F_INGRESS)) {
+			NL_SET_ERR_MSG(extack,
+				       "Specified parent ID is reserved for ingress and clsact Qdiscs");
+			err = -EINVAL;
+			goto err_out3;
+		}
 		handle = TC_H_MAKE(TC_H_INGRESS, 0);
 	} else {
 		if (handle == 0) {
@@ -1460,7 +1476,7 @@
 				q = dev_ingress_queue(dev)->qdisc_sleeping;
 			}
 		} else {
-			q = dev->qdisc;
+			q = rtnl_dereference(dev->qdisc);
 		}
 		if (!q) {
 			NL_SET_ERR_MSG(extack, "Cannot find specified qdisc on specified device");
@@ -1502,10 +1518,28 @@
 	return 0;
 }
 
+static bool req_create_or_replace(struct nlmsghdr *n)
+{
+	return (n->nlmsg_flags & NLM_F_CREATE &&
+		n->nlmsg_flags & NLM_F_REPLACE);
+}
+
+static bool req_create_exclusive(struct nlmsghdr *n)
+{
+	return (n->nlmsg_flags & NLM_F_CREATE &&
+		n->nlmsg_flags & NLM_F_EXCL);
+}
+
+static bool req_change(struct nlmsghdr *n)
+{
+	return (!(n->nlmsg_flags & NLM_F_CREATE) &&
+		!(n->nlmsg_flags & NLM_F_REPLACE) &&
+		!(n->nlmsg_flags & NLM_F_EXCL));
+}
+
 /*
  * Create/change qdisc.
  */
-
 static int tc_modify_qdisc(struct sk_buff *skb, struct nlmsghdr *n,
 			   struct netlink_ext_ack *extack)
 {
@@ -1549,7 +1583,7 @@
 				q = dev_ingress_queue(dev)->qdisc_sleeping;
 			}
 		} else {
-			q = dev->qdisc;
+			q = rtnl_dereference(dev->qdisc);
 		}
 
 		/* It may be default qdisc, ignore it */
@@ -1569,6 +1603,10 @@
 				q = qdisc_lookup(dev, tcm->tcm_handle);
 				if (!q)
 					goto create_n_graft;
+				if (q->parent != tcm->tcm_parent) {
+					NL_SET_ERR_MSG(extack, "Cannot move an existing qdisc to a different parent");
+					return -EINVAL;
+				}
 				if (n->nlmsg_flags & NLM_F_EXCL) {
 					NL_SET_ERR_MSG(extack, "Exclusivity flag on, cannot override");
 					return -EEXIST;
@@ -1578,11 +1616,20 @@
 					NL_SET_ERR_MSG(extack, "Invalid qdisc name");
 					return -EINVAL;
 				}
+				if (q->flags & TCQ_F_INGRESS) {
+					NL_SET_ERR_MSG(extack,
+						       "Cannot regraft ingress or clsact Qdiscs");
+					return -EINVAL;
+				}
 				if (q == p ||
 				    (p && check_loop(q, p, 0))) {
 					NL_SET_ERR_MSG(extack, "Qdisc parent/child loop detected");
 					return -ELOOP;
 				}
+				if (clid == TC_H_INGRESS) {
+					NL_SET_ERR_MSG(extack, "Ingress cannot graft directly");
+					return -EINVAL;
+				}
 				qdisc_refcount_inc(q);
 				goto graft;
 			} else {
@@ -1593,27 +1640,35 @@
 				 *
 				 *   We know, that some child q is already
 				 *   attached to this parent and have choice:
-				 *   either to change it or to create/graft new one.
+				 *   1) change it or 2) create/graft new one.
+				 *   If the requested qdisc kind is different
+				 *   than the existing one, then we choose graft.
+				 *   If they are the same then this is "change"
+				 *   operation - just let it fallthrough..
 				 *
 				 *   1. We are allowed to create/graft only
-				 *   if CREATE and REPLACE flags are set.
+				 *   if the request is explicitly stating
+				 *   "please create if it doesn't exist".
 				 *
-				 *   2. If EXCL is set, requestor wanted to say,
-				 *   that qdisc tcm_handle is not expected
+				 *   2. If the request is to exclusive create
+				 *   then the qdisc tcm_handle is not expected
 				 *   to exist, so that we choose create/graft too.
 				 *
 				 *   3. The last case is when no flags are set.
+				 *   This will happen when for example tc
+				 *   utility issues a "change" command.
 				 *   Alas, it is sort of hole in API, we
 				 *   cannot decide what to do unambiguously.
-				 *   For now we select create/graft, if
-				 *   user gave KIND, which does not match existing.
+				 *   For now we select create/graft.
 				 */
-				if ((n->nlmsg_flags & NLM_F_CREATE) &&
-				    (n->nlmsg_flags & NLM_F_REPLACE) &&
-				    ((n->nlmsg_flags & NLM_F_EXCL) ||
-				     (tca[TCA_KIND] &&
-				      nla_strcmp(tca[TCA_KIND], q->ops->id))))
-					goto create_n_graft;
+				if (tca[TCA_KIND] &&
+				    nla_strcmp(tca[TCA_KIND], q->ops->id)) {
+					if (req_create_or_replace(n) ||
+					    req_create_exclusive(n))
+						goto create_n_graft;
+					else if (req_change(n))
+						goto create_n_graft2;
+				}
 			}
 		}
 	} else {
@@ -1647,6 +1702,7 @@
 		NL_SET_ERR_MSG(extack, "Qdisc not found. To create specify NLM_F_CREATE flag");
 		return -ENOENT;
 	}
+create_n_graft2:
 	if (clid == TC_H_INGRESS) {
 		if (dev_ingress_queue(dev)) {
 			q = qdisc_create(dev, dev_ingress_queue(dev), p,
@@ -1771,7 +1827,8 @@
 			s_q_idx = 0;
 		q_idx = 0;
 
-		if (tc_dump_qdisc_root(dev->qdisc, skb, cb, &q_idx, s_q_idx,
+		if (tc_dump_qdisc_root(rtnl_dereference(dev->qdisc),
+				       skb, cb, &q_idx, s_q_idx,
 				       true, tca[TCA_DUMP_INVISIBLE]) < 0)
 			goto done;
 
@@ -2042,7 +2099,7 @@
 		} else if (qid1) {
 			qid = qid1;
 		} else if (qid == 0)
-			qid = dev->qdisc->handle;
+			qid = rtnl_dereference(dev->qdisc)->handle;
 
 		/* Now qid is genuine qdisc handle consistent
 		 * both with parent and child.
@@ -2053,7 +2110,7 @@
 			portid = TC_H_MAKE(qid, portid);
 	} else {
 		if (qid == 0)
-			qid = dev->qdisc->handle;
+			qid = rtnl_dereference(dev->qdisc)->handle;
 	}
 
 	/* OK. Locate qdisc */
@@ -2107,6 +2164,12 @@
 		return -EOPNOTSUPP;
 	}
 
+	/* Prevent creation of traffic classes with classid TC_H_ROOT */
+	if (clid == TC_H_ROOT) {
+		NL_SET_ERR_MSG(extack, "Cannot create traffic class with classid TC_H_ROOT");
+		return -EINVAL;
+	}
+
 	new_cl = cl;
 	err = -EOPNOTSUPP;
 	if (cops->change)
@@ -2214,7 +2277,8 @@
 	s_t = cb->args[0];
 	t = 0;
 
-	if (tc_dump_tclass_root(dev->qdisc, skb, tcm, cb, &t, s_t, true) < 0)
+	if (tc_dump_tclass_root(rtnl_dereference(dev->qdisc),
+				skb, tcm, cb, &t, s_t, true) < 0)
 		goto done;
 
 	dev_queue = dev_ingress_queue(dev);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_cake.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_cake.c
@@ -643,6 +643,63 @@
 	return (flow_mode & CAKE_FLOW_DUAL_DST) == CAKE_FLOW_DUAL_DST;
 }
 
+static void cake_dec_srchost_bulk_flow_count(struct cake_tin_data *q,
+					     struct cake_flow *flow,
+					     int flow_mode)
+{
+	if (likely(cake_dsrc(flow_mode) &&
+		   q->hosts[flow->srchost].srchost_bulk_flow_count))
+		q->hosts[flow->srchost].srchost_bulk_flow_count--;
+}
+
+static void cake_inc_srchost_bulk_flow_count(struct cake_tin_data *q,
+					     struct cake_flow *flow,
+					     int flow_mode)
+{
+	if (likely(cake_dsrc(flow_mode) &&
+		   q->hosts[flow->srchost].srchost_bulk_flow_count < CAKE_QUEUES))
+		q->hosts[flow->srchost].srchost_bulk_flow_count++;
+}
+
+static void cake_dec_dsthost_bulk_flow_count(struct cake_tin_data *q,
+					     struct cake_flow *flow,
+					     int flow_mode)
+{
+	if (likely(cake_ddst(flow_mode) &&
+		   q->hosts[flow->dsthost].dsthost_bulk_flow_count))
+		q->hosts[flow->dsthost].dsthost_bulk_flow_count--;
+}
+
+static void cake_inc_dsthost_bulk_flow_count(struct cake_tin_data *q,
+					     struct cake_flow *flow,
+					     int flow_mode)
+{
+	if (likely(cake_ddst(flow_mode) &&
+		   q->hosts[flow->dsthost].dsthost_bulk_flow_count < CAKE_QUEUES))
+		q->hosts[flow->dsthost].dsthost_bulk_flow_count++;
+}
+
+static u16 cake_get_flow_quantum(struct cake_tin_data *q,
+				 struct cake_flow *flow,
+				 int flow_mode)
+{
+	u16 host_load = 1;
+
+	if (cake_dsrc(flow_mode))
+		host_load = max(host_load,
+				q->hosts[flow->srchost].srchost_bulk_flow_count);
+
+	if (cake_ddst(flow_mode))
+		host_load = max(host_load,
+				q->hosts[flow->dsthost].dsthost_bulk_flow_count);
+
+	/* The shifted prandom_u32() is a way to apply dithering to avoid
+	 * accumulating roundoff errors
+	 */
+	return (q->flow_quantum * quantum_div[host_load] +
+		(prandom_u32() >> 16)) >> 16;
+}
+
 static u32 cake_hash(struct cake_tin_data *q, const struct sk_buff *skb,
 		     int flow_mode, u16 flow_override, u16 host_override)
 {
@@ -785,12 +842,13 @@
 		 * queue, accept the collision, update the host tags.
 		 */
 		q->way_collisions++;
-		if (q->flows[outer_hash + k].set == CAKE_SET_BULK) {
-			q->hosts[q->flows[reduced_hash].srchost].srchost_bulk_flow_count--;
-			q->hosts[q->flows[reduced_hash].dsthost].dsthost_bulk_flow_count--;
-		}
 		allocate_src = cake_dsrc(flow_mode);
 		allocate_dst = cake_ddst(flow_mode);
+
+		if (q->flows[outer_hash + k].set == CAKE_SET_BULK) {
+			cake_dec_srchost_bulk_flow_count(q, &q->flows[outer_hash + k], flow_mode);
+			cake_dec_dsthost_bulk_flow_count(q, &q->flows[outer_hash + k], flow_mode);
+		}
 found:
 		/* reserve queue for future packets in same flow */
 		reduced_hash = outer_hash + k;
@@ -814,9 +872,10 @@
 			q->hosts[outer_hash + k].srchost_tag = srchost_hash;
 found_src:
 			srchost_idx = outer_hash + k;
-			if (q->flows[reduced_hash].set == CAKE_SET_BULK)
-				q->hosts[srchost_idx].srchost_bulk_flow_count++;
 			q->flows[reduced_hash].srchost = srchost_idx;
+
+			if (q->flows[reduced_hash].set == CAKE_SET_BULK)
+				cake_inc_srchost_bulk_flow_count(q, &q->flows[reduced_hash], flow_mode);
 		}
 
 		if (allocate_dst) {
@@ -837,9 +896,10 @@
 			q->hosts[outer_hash + k].dsthost_tag = dsthost_hash;
 found_dst:
 			dsthost_idx = outer_hash + k;
-			if (q->flows[reduced_hash].set == CAKE_SET_BULK)
-				q->hosts[dsthost_idx].dsthost_bulk_flow_count++;
 			q->flows[reduced_hash].dsthost = dsthost_idx;
+
+			if (q->flows[reduced_hash].set == CAKE_SET_BULK)
+				cake_inc_dsthost_bulk_flow_count(q, &q->flows[reduced_hash], flow_mode);
 		}
 	}
 
@@ -1538,7 +1598,6 @@
 	b->backlogs[idx]    -= len;
 	b->tin_backlog      -= len;
 	sch->qstats.backlog -= len;
-	qdisc_tree_reduce_backlog(sch, 1, len);
 
 	flow->dropped++;
 	b->tin_dropped++;
@@ -1549,6 +1608,7 @@
 
 	__qdisc_drop(skb, to_free);
 	sch->q.qlen--;
+	qdisc_tree_reduce_backlog(sch, 1, len);
 
 	cake_heapify(q, 0);
 
@@ -1852,10 +1912,6 @@
 
 	/* flowchain */
 	if (!flow->set || flow->set == CAKE_SET_DECAYING) {
-		struct cake_host *srchost = &b->hosts[flow->srchost];
-		struct cake_host *dsthost = &b->hosts[flow->dsthost];
-		u16 host_load = 1;
-
 		if (!flow->set) {
 			list_add_tail(&flow->flowchain, &b->new_flows);
 		} else {
@@ -1865,18 +1921,8 @@
 		flow->set = CAKE_SET_SPARSE;
 		b->sparse_flow_count++;
 
-		if (cake_dsrc(q->flow_mode))
-			host_load = max(host_load, srchost->srchost_bulk_flow_count);
-
-		if (cake_ddst(q->flow_mode))
-			host_load = max(host_load, dsthost->dsthost_bulk_flow_count);
-
-		flow->deficit = (b->flow_quantum *
-				 quantum_div[host_load]) >> 16;
+		flow->deficit = cake_get_flow_quantum(b, flow, q->flow_mode);
 	} else if (flow->set == CAKE_SET_SPARSE_WAIT) {
-		struct cake_host *srchost = &b->hosts[flow->srchost];
-		struct cake_host *dsthost = &b->hosts[flow->dsthost];
-
 		/* this flow was empty, accounted as a sparse flow, but actually
 		 * in the bulk rotation.
 		 */
@@ -1884,12 +1930,8 @@
 		b->sparse_flow_count--;
 		b->bulk_flow_count++;
 
-		if (cake_dsrc(q->flow_mode))
-			srchost->srchost_bulk_flow_count++;
-
-		if (cake_ddst(q->flow_mode))
-			dsthost->dsthost_bulk_flow_count++;
-
+		cake_inc_srchost_bulk_flow_count(b, flow, q->flow_mode);
+		cake_inc_dsthost_bulk_flow_count(b, flow, q->flow_mode);
 	}
 
 	if (q->buffer_used > q->buffer_max_used)
@@ -1946,13 +1988,11 @@
 {
 	struct cake_sched_data *q = qdisc_priv(sch);
 	struct cake_tin_data *b = &q->tins[q->cur_tin];
-	struct cake_host *srchost, *dsthost;
 	ktime_t now = ktime_get();
 	struct cake_flow *flow;
 	struct list_head *head;
 	bool first_flow = true;
 	struct sk_buff *skb;
-	u16 host_load;
 	u64 delay;
 	u32 len;
 
@@ -2052,11 +2092,6 @@
 	q->cur_flow = flow - b->flows;
 	first_flow = false;
 
-	/* triple isolation (modified DRR++) */
-	srchost = &b->hosts[flow->srchost];
-	dsthost = &b->hosts[flow->dsthost];
-	host_load = 1;
-
 	/* flow isolation (DRR++) */
 	if (flow->deficit <= 0) {
 		/* Keep all flows with deficits out of the sparse and decaying
@@ -2068,11 +2103,8 @@
 				b->sparse_flow_count--;
 				b->bulk_flow_count++;
 
-				if (cake_dsrc(q->flow_mode))
-					srchost->srchost_bulk_flow_count++;
-
-				if (cake_ddst(q->flow_mode))
-					dsthost->dsthost_bulk_flow_count++;
+				cake_inc_srchost_bulk_flow_count(b, flow, q->flow_mode);
+				cake_inc_dsthost_bulk_flow_count(b, flow, q->flow_mode);
 
 				flow->set = CAKE_SET_BULK;
 			} else {
@@ -2084,19 +2116,7 @@
 			}
 		}
 
-		if (cake_dsrc(q->flow_mode))
-			host_load = max(host_load, srchost->srchost_bulk_flow_count);
-
-		if (cake_ddst(q->flow_mode))
-			host_load = max(host_load, dsthost->dsthost_bulk_flow_count);
-
-		WARN_ON(host_load > CAKE_QUEUES);
-
-		/* The shifted prandom_u32() is a way to apply dithering to
-		 * avoid accumulating roundoff errors
-		 */
-		flow->deficit += (b->flow_quantum * quantum_div[host_load] +
-				  (prandom_u32() >> 16)) >> 16;
+		flow->deficit += cake_get_flow_quantum(b, flow, q->flow_mode);
 		list_move_tail(&flow->flowchain, &b->old_flows);
 
 		goto retry;
@@ -2120,11 +2140,8 @@
 				if (flow->set == CAKE_SET_BULK) {
 					b->bulk_flow_count--;
 
-					if (cake_dsrc(q->flow_mode))
-						srchost->srchost_bulk_flow_count--;
-
-					if (cake_ddst(q->flow_mode))
-						dsthost->dsthost_bulk_flow_count--;
+					cake_dec_srchost_bulk_flow_count(b, flow, q->flow_mode);
+					cake_dec_dsthost_bulk_flow_count(b, flow, q->flow_mode);
 
 					b->decaying_flow_count++;
 				} else if (flow->set == CAKE_SET_SPARSE ||
@@ -2142,12 +2159,8 @@
 				else if (flow->set == CAKE_SET_BULK) {
 					b->bulk_flow_count--;
 
-					if (cake_dsrc(q->flow_mode))
-						srchost->srchost_bulk_flow_count--;
-
-					if (cake_ddst(q->flow_mode))
-						dsthost->dsthost_bulk_flow_count--;
-
+					cake_dec_srchost_bulk_flow_count(b, flow, q->flow_mode);
+					cake_dec_dsthost_bulk_flow_count(b, flow, q->flow_mode);
 				} else
 					b->decaying_flow_count--;
 
@@ -2224,8 +2237,12 @@
 
 static void cake_reset(struct Qdisc *sch)
 {
+	struct cake_sched_data *q = qdisc_priv(sch);
 	u32 c;
 
+	if (!q->tins)
+		return;
+
 	for (c = 0; c < CAKE_MAX_TINS; c++)
 		cake_clear_tin(sch, c);
 }
@@ -2736,7 +2753,7 @@
 	q->tins = kvcalloc(CAKE_MAX_TINS, sizeof(struct cake_tin_data),
 			   GFP_KERNEL);
 	if (!q->tins)
-		goto nomem;
+		return -ENOMEM;
 
 	for (i = 0; i < CAKE_MAX_TINS; i++) {
 		struct cake_tin_data *b = q->tins + i;
@@ -2766,10 +2783,6 @@
 	q->min_netlen = ~0;
 	q->min_adjlen = ~0;
 	return 0;
-
-nomem:
-	cake_destroy(sch);
-	return -ENOMEM;
 }
 
 static int cake_dump(struct Qdisc *sch, struct sk_buff *skb)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_cbs.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_cbs.c
@@ -310,7 +310,7 @@
 {
 	struct ethtool_link_ksettings ecmd;
 	int speed = SPEED_10;
-	int port_rate;
+	s64 port_rate;
 	int err;
 
 	err = __ethtool_get_link_ksettings(dev, &ecmd);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_choke.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_choke.c
@@ -124,10 +124,10 @@
 	if (idx == q->tail)
 		choke_zap_tail_holes(q);
 
+	--sch->q.qlen;
 	qdisc_qstats_backlog_dec(sch, skb);
 	qdisc_tree_reduce_backlog(sch, 1, qdisc_pkt_len(skb));
 	qdisc_drop(skb, sch, to_free);
-	--sch->q.qlen;
 }
 
 struct choke_skb_cb {
@@ -315,8 +315,6 @@
 		rtnl_qdisc_drop(skb, sch);
 	}
 
-	sch->q.qlen = 0;
-	sch->qstats.backlog = 0;
 	if (q->tab)
 		memset(q->tab, 0, (q->tab_mask + 1) * sizeof(struct sk_buff *));
 	q->head = q->tail = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_drr.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_drr.c
@@ -444,8 +444,6 @@
 			qdisc_reset(cl->qdisc);
 		}
 	}
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 }
 
 static void drr_destroy_qdisc(struct Qdisc *sch)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_etf.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_etf.c
@@ -445,9 +445,6 @@
 	timesortedlist_clear(sch);
 	__qdisc_reset_queue(&sch->q);
 
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
-
 	q->last = 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_ets.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_ets.c
@@ -91,6 +91,8 @@
 {
 	struct ets_sched *q = qdisc_priv(sch);
 
+	if (arg == 0 || arg > q->nbands)
+		return NULL;
 	return &q->classes[arg - 1];
 }
 
@@ -667,12 +669,14 @@
 			q->classes[i].deficit = quanta[i];
 		}
 	}
+	for (i = q->nbands; i < oldbands; i++) {
+		if (i >= q->nstrict && q->classes[i].qdisc->q.qlen)
+			list_del(&q->classes[i].alist);
+		qdisc_tree_flush_backlog(q->classes[i].qdisc);
+	}
 	q->nstrict = nstrict;
 	memcpy(q->prio2band, priomap, sizeof(priomap));
 
-	for (i = q->nbands; i < oldbands; i++)
-		qdisc_tree_flush_backlog(q->classes[i].qdisc);
-
 	for (i = 0; i < q->nbands; i++)
 		q->classes[i].quantum = quanta[i];
 
@@ -720,8 +724,6 @@
 	}
 	for (band = 0; band < q->nbands; band++)
 		qdisc_reset(q->classes[band].qdisc);
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 }
 
 static void ets_qdisc_destroy(struct Qdisc *sch)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_fifo.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_fifo.c
@@ -39,6 +39,9 @@
 {
 	unsigned int prev_backlog;
 
+	if (unlikely(READ_ONCE(sch->limit) == 0))
+		return qdisc_drop(skb, sch, to_free);
+
 	if (likely(sch->q.qlen < sch->limit))
 		return qdisc_enqueue_tail(skb, sch);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_fq.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_fq.c
@@ -779,13 +779,17 @@
 	return 0;
 }
 
+static struct netlink_range_validation iq_range = {
+	.max = INT_MAX,
+};
+
 static const struct nla_policy fq_policy[TCA_FQ_MAX + 1] = {
 	[TCA_FQ_UNSPEC]			= { .strict_start_type = TCA_FQ_TIMER_SLACK },
 
 	[TCA_FQ_PLIMIT]			= { .type = NLA_U32 },
 	[TCA_FQ_FLOW_PLIMIT]		= { .type = NLA_U32 },
 	[TCA_FQ_QUANTUM]		= { .type = NLA_U32 },
-	[TCA_FQ_INITIAL_QUANTUM]	= { .type = NLA_U32 },
+	[TCA_FQ_INITIAL_QUANTUM]	= NLA_POLICY_FULL_RANGE(NLA_U32, &iq_range),
 	[TCA_FQ_RATE_ENABLE]		= { .type = NLA_U32 },
 	[TCA_FQ_FLOW_DEFAULT_RATE]	= { .type = NLA_U32 },
 	[TCA_FQ_FLOW_MAX_RATE]		= { .type = NLA_U32 },
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_fq_codel.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_fq_codel.c
@@ -347,8 +347,6 @@
 		codel_vars_init(&flow->cvars);
 	}
 	memset(q->backlogs, 0, q->flows_cnt * sizeof(u32));
-	sch->q.qlen = 0;
-	sch->qstats.backlog = 0;
 	q->memory_usage = 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_fq_pie.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_fq_pie.c
@@ -61,6 +61,7 @@
 	struct pie_params p_params;
 	u32 ecn_prob;
 	u32 flows_cnt;
+	u32 flows_cursor;
 	u32 quantum;
 	u32 memory_limit;
 	u32 new_flow_count;
@@ -201,6 +202,11 @@
 	return NET_XMIT_CN;
 }
 
+static struct netlink_range_validation fq_pie_q_range = {
+	.min = 1,
+	.max = 1 << 20,
+};
+
 static const struct nla_policy fq_pie_policy[TCA_FQ_PIE_MAX + 1] = {
 	[TCA_FQ_PIE_LIMIT]		= {.type = NLA_U32},
 	[TCA_FQ_PIE_FLOWS]		= {.type = NLA_U32},
@@ -208,7 +214,8 @@
 	[TCA_FQ_PIE_TUPDATE]		= {.type = NLA_U32},
 	[TCA_FQ_PIE_ALPHA]		= {.type = NLA_U32},
 	[TCA_FQ_PIE_BETA]		= {.type = NLA_U32},
-	[TCA_FQ_PIE_QUANTUM]		= {.type = NLA_U32},
+	[TCA_FQ_PIE_QUANTUM]		=
+			NLA_POLICY_FULL_RANGE(NLA_U32, &fq_pie_q_range),
 	[TCA_FQ_PIE_MEMORY_LIMIT]	= {.type = NLA_U32},
 	[TCA_FQ_PIE_ECN_PROB]		= {.type = NLA_U32},
 	[TCA_FQ_PIE_ECN]		= {.type = NLA_U32},
@@ -372,21 +379,31 @@
 static void fq_pie_timer(struct timer_list *t)
 {
 	struct fq_pie_sched_data *q = from_timer(q, t, adapt_timer);
+	unsigned long next, tupdate;
 	struct Qdisc *sch = q->sch;
 	spinlock_t *root_lock; /* to lock qdisc for probability calculations */
-	u32 idx;
+	int max_cnt, i;
 
 	root_lock = qdisc_lock(qdisc_root_sleeping(sch));
 	spin_lock(root_lock);
 
-	for (idx = 0; idx < q->flows_cnt; idx++)
-		pie_calculate_probability(&q->p_params, &q->flows[idx].vars,
-					  q->flows[idx].backlog);
-
-	/* reset the timer to fire after 'tupdate' jiffies. */
-	if (q->p_params.tupdate)
-		mod_timer(&q->adapt_timer, jiffies + q->p_params.tupdate);
-
+	/* Limit this expensive loop to 2048 flows per round. */
+	max_cnt = min_t(int, q->flows_cnt - q->flows_cursor, 2048);
+	for (i = 0; i < max_cnt; i++) {
+		pie_calculate_probability(&q->p_params,
+					  &q->flows[q->flows_cursor].vars,
+					  q->flows[q->flows_cursor].backlog);
+		q->flows_cursor++;
+	}
+
+	tupdate = q->p_params.tupdate;
+	next = 0;
+	if (q->flows_cursor >= q->flows_cnt) {
+		q->flows_cursor = 0;
+		next = tupdate;
+	}
+	if (tupdate)
+		mod_timer(&q->adapt_timer, jiffies + next);
 	spin_unlock(root_lock);
 }
 
@@ -521,9 +538,6 @@
 		INIT_LIST_HEAD(&flow->flowchain);
 		pie_vars_init(&flow->vars);
 	}
-
-	sch->q.qlen = 0;
-	sch->qstats.backlog = 0;
 }
 
 static void fq_pie_destroy(struct Qdisc *sch)
@@ -531,6 +545,7 @@
 	struct fq_pie_sched_data *q = qdisc_priv(sch);
 
 	tcf_block_put(q->block);
+	q->p_params.tupdate = 0;
 	del_timer_sync(&q->adapt_timer);
 	kvfree(q->flows);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_frag.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_frag.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB
 #include <net/netlink.h>
 #include <net/sch_generic.h>
+#include <net/pkt_sched.h>
 #include <net/dst.h>
 #include <net/ip.h>
 #include <net/ip6_fib.h>
@@ -137,7 +138,7 @@
 
 int sch_frag_xmit_hook(struct sk_buff *skb, int (*xmit)(struct sk_buff *skb))
 {
-	u16 mru = qdisc_skb_cb(skb)->mru;
+	u16 mru = tc_skb_cb(skb)->mru;
 	int err;
 
 	if (mru && skb->len > mru + skb->dev->hard_header_len)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_generic.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_generic.c
@@ -409,7 +409,7 @@
 
 void __qdisc_run(struct Qdisc *q)
 {
-	int quota = dev_tx_weight;
+	int quota = READ_ONCE(dev_tx_weight);
 	int packets;
 
 	while (qdisc_restart(q, &packets)) {
@@ -1083,6 +1083,21 @@
 }
 EXPORT_SYMBOL(dev_graft_qdisc);
 
+static void shutdown_scheduler_queue(struct net_device *dev,
+				     struct netdev_queue *dev_queue,
+				     void *_qdisc_default)
+{
+	struct Qdisc *qdisc = dev_queue->qdisc_sleeping;
+	struct Qdisc *qdisc_default = _qdisc_default;
+
+	if (qdisc) {
+		rcu_assign_pointer(dev_queue->qdisc, qdisc_default);
+		dev_queue->qdisc_sleeping = qdisc_default;
+
+		qdisc_put(qdisc);
+	}
+}
+
 static void attach_one_default_qdisc(struct net_device *dev,
 				     struct netdev_queue *dev_queue,
 				     void *_unused)
@@ -1114,30 +1129,34 @@
 	if (!netif_is_multiqueue(dev) ||
 	    dev->priv_flags & IFF_NO_QUEUE) {
 		netdev_for_each_tx_queue(dev, attach_one_default_qdisc, NULL);
-		dev->qdisc = txq->qdisc_sleeping;
-		qdisc_refcount_inc(dev->qdisc);
+		qdisc = txq->qdisc_sleeping;
+		rcu_assign_pointer(dev->qdisc, qdisc);
+		qdisc_refcount_inc(qdisc);
 	} else {
 		qdisc = qdisc_create_dflt(txq, &mq_qdisc_ops, TC_H_ROOT, NULL);
 		if (qdisc) {
-			dev->qdisc = qdisc;
+			rcu_assign_pointer(dev->qdisc, qdisc);
 			qdisc->ops->attach(qdisc);
 		}
 	}
+	qdisc = rtnl_dereference(dev->qdisc);
 
 	/* Detect default qdisc setup/init failed and fallback to "noqueue" */
-	if (dev->qdisc == &noop_qdisc) {
+	if (qdisc == &noop_qdisc) {
 		netdev_warn(dev, "default qdisc (%s) fail, fallback to %s\n",
 			    default_qdisc_ops->id, noqueue_qdisc_ops.id);
+		netdev_for_each_tx_queue(dev, shutdown_scheduler_queue, &noop_qdisc);
 		dev->priv_flags |= IFF_NO_QUEUE;
 		netdev_for_each_tx_queue(dev, attach_one_default_qdisc, NULL);
-		dev->qdisc = txq->qdisc_sleeping;
-		qdisc_refcount_inc(dev->qdisc);
+		qdisc = txq->qdisc_sleeping;
+		rcu_assign_pointer(dev->qdisc, qdisc);
+		qdisc_refcount_inc(qdisc);
 		dev->priv_flags ^= IFF_NO_QUEUE;
 	}
 
 #ifdef CONFIG_NET_SCHED
-	if (dev->qdisc != &noop_qdisc)
-		qdisc_hash_add(dev->qdisc, false);
+	if (qdisc != &noop_qdisc)
+		qdisc_hash_add(qdisc, false);
 #endif
 }
 
@@ -1167,7 +1186,7 @@
 	 * and noqueue_qdisc for virtual interfaces
 	 */
 
-	if (dev->qdisc == &noop_qdisc)
+	if (rtnl_dereference(dev->qdisc) == &noop_qdisc)
 		attach_default_qdiscs(dev);
 
 	if (!netif_carrier_ok(dev))
@@ -1330,6 +1349,15 @@
 	return 0;
 }
 
+void dev_qdisc_change_real_num_tx(struct net_device *dev,
+				  unsigned int new_real_tx)
+{
+	struct Qdisc *qdisc = rtnl_dereference(dev->qdisc);
+
+	if (qdisc->ops->change_real_num_tx)
+		qdisc->ops->change_real_num_tx(qdisc, new_real_tx);
+}
+
 int dev_qdisc_change_tx_queue_len(struct net_device *dev)
 {
 	bool up = dev->flags & IFF_UP;
@@ -1364,7 +1392,7 @@
 
 void dev_init_scheduler(struct net_device *dev)
 {
-	dev->qdisc = &noop_qdisc;
+	rcu_assign_pointer(dev->qdisc, &noop_qdisc);
 	netdev_for_each_tx_queue(dev, dev_init_scheduler_queue, &noop_qdisc);
 	if (dev_ingress_queue(dev))
 		dev_init_scheduler_queue(dev, dev_ingress_queue(dev), &noop_qdisc);
@@ -1372,28 +1400,13 @@
 	timer_setup(&dev->watchdog_timer, dev_watchdog, 0);
 }
 
-static void shutdown_scheduler_queue(struct net_device *dev,
-				     struct netdev_queue *dev_queue,
-				     void *_qdisc_default)
-{
-	struct Qdisc *qdisc = dev_queue->qdisc_sleeping;
-	struct Qdisc *qdisc_default = _qdisc_default;
-
-	if (qdisc) {
-		rcu_assign_pointer(dev_queue->qdisc, qdisc_default);
-		dev_queue->qdisc_sleeping = qdisc_default;
-
-		qdisc_put(qdisc);
-	}
-}
-
 void dev_shutdown(struct net_device *dev)
 {
 	netdev_for_each_tx_queue(dev, shutdown_scheduler_queue, &noop_qdisc);
 	if (dev_ingress_queue(dev))
 		shutdown_scheduler_queue(dev, dev_ingress_queue(dev), &noop_qdisc);
-	qdisc_put(dev->qdisc);
-	dev->qdisc = &noop_qdisc;
+	qdisc_put(rtnl_dereference(dev->qdisc));
+	rcu_assign_pointer(dev->qdisc, &noop_qdisc);
 
 	WARN_ON(timer_pending(&dev->watchdog_timer));
 }
@@ -1446,6 +1459,7 @@
 {
 	memset(r, 0, sizeof(*r));
 	r->overhead = conf->overhead;
+	r->mpu = conf->mpu;
 	r->rate_bytes_ps = max_t(u64, conf->rate, rate64);
 	r->linklayer = (conf->linklayer & TC_LINKLAYER_MASK);
 	psched_ratecfg_precompute__(r->rate_bytes_ps, &r->mult, &r->shift);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_hfsc.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_hfsc.c
@@ -903,6 +903,14 @@
 	cl->cl_flags |= HFSC_USC;
 }
 
+static void
+hfsc_upgrade_rt(struct hfsc_class *cl)
+{
+	cl->cl_fsc = cl->cl_rsc;
+	rtsc_init(&cl->cl_virtual, &cl->cl_fsc, cl->cl_vt, cl->cl_total);
+	cl->cl_flags |= HFSC_FSC;
+}
+
 static const struct nla_policy hfsc_policy[TCA_HFSC_MAX + 1] = {
 	[TCA_HFSC_RSC]	= { .len = sizeof(struct tc_service_curve) },
 	[TCA_HFSC_FSC]	= { .len = sizeof(struct tc_service_curve) },
@@ -1064,6 +1072,12 @@
 	cl->cf_tree = RB_ROOT;
 
 	sch_tree_lock(sch);
+	/* Check if the inner class is a misconfigured 'rt' */
+	if (!(parent->cl_flags & HFSC_FSC) && parent != &q->root) {
+		NL_SET_ERR_MSG(extack,
+			       "Forced curve change on parent 'rt' to 'sc'");
+		hfsc_upgrade_rt(parent);
+	}
 	qdisc_class_hash_insert(&q->clhash, &cl->cl_common);
 	list_add_tail(&cl->siblings, &parent->children);
 	if (parent->level == 0)
@@ -1485,8 +1499,6 @@
 	}
 	q->eligible = RB_ROOT;
 	qdisc_watchdog_cancel(&q->watchdog);
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_htb.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_htb.c
@@ -427,7 +427,10 @@
 	while (cl->cmode == HTB_MAY_BORROW && p && mask) {
 		m = mask;
 		while (m) {
-			int prio = ffz(~m);
+			unsigned int prio = ffz(~m);
+
+			if (WARN_ON_ONCE(prio >= ARRAY_SIZE(p->inner.clprio)))
+				break;
 			m &= ~(1 << prio);
 
 			if (p->inner.clprio[prio].feed.rb_node)
@@ -1008,8 +1011,6 @@
 	}
 	qdisc_watchdog_cancel(&q->watchdog);
 	__qdisc_reset_queue(&q->direct_queue);
-	sch->q.qlen = 0;
-	sch->qstats.backlog = 0;
 	memset(q->hlevel, 0, sizeof(q->hlevel));
 	memset(q->row_mask, 0, sizeof(q->row_mask));
 }
@@ -1560,7 +1561,7 @@
 	struct tc_htb_qopt_offload offload_opt;
 	struct netdev_queue *dev_queue;
 	struct Qdisc *q = cl->leaf.q;
-	struct Qdisc *old = NULL;
+	struct Qdisc *old;
 	int err;
 
 	if (cl->level)
@@ -1568,14 +1569,17 @@
 
 	WARN_ON(!q);
 	dev_queue = htb_offload_get_queue(cl);
-	old = htb_graft_helper(dev_queue, NULL);
-	if (destroying)
-		/* Before HTB is destroyed, the kernel grafts noop_qdisc to
-		 * all queues.
+	/* When destroying, caller qdisc_graft grafts the new qdisc and invokes
+	 * qdisc_put for the qdisc being destroyed. htb_destroy_class_offload
+	 * does not need to graft or qdisc_put the qdisc being destroyed.
+	 */
+	if (!destroying) {
+		old = htb_graft_helper(dev_queue, NULL);
+		/* Last qdisc grafted should be the same as cl->leaf.q when
+		 * calling htb_delete.
 		 */
-		WARN_ON(!(old->flags & TCQ_F_BUILTIN));
-	else
 		WARN_ON(old != q);
+	}
 
 	if (cl->parent) {
 		cl->parent->bstats_bias.bytes += q->bstats.bytes;
@@ -1591,10 +1595,12 @@
 	};
 	err = htb_offload(qdisc_dev(sch), &offload_opt);
 
-	if (!err || destroying)
-		qdisc_put(old);
-	else
-		htb_graft_helper(dev_queue, old);
+	if (!destroying) {
+		if (!err)
+			qdisc_put(old);
+		else
+			htb_graft_helper(dev_queue, old);
+	}
 
 	if (last_child)
 		return err;
@@ -1803,6 +1809,26 @@
 	if (!hopt->rate.rate || !hopt->ceil.rate)
 		goto failure;
 
+	if (q->offload) {
+		/* Options not supported by the offload. */
+		if (hopt->rate.overhead || hopt->ceil.overhead) {
+			NL_SET_ERR_MSG(extack, "HTB offload doesn't support the overhead parameter");
+			goto failure;
+		}
+		if (hopt->rate.mpu || hopt->ceil.mpu) {
+			NL_SET_ERR_MSG(extack, "HTB offload doesn't support the mpu parameter");
+			goto failure;
+		}
+		if (hopt->quantum) {
+			NL_SET_ERR_MSG(extack, "HTB offload doesn't support the quantum parameter");
+			goto failure;
+		}
+		if (hopt->prio) {
+			NL_SET_ERR_MSG(extack, "HTB offload doesn't support the prio parameter");
+			goto failure;
+		}
+	}
+
 	/* Keeping backward compatible with rate_table based iproute2 tc */
 	if (hopt->rate.linklayer == TC_LINKLAYER_UNAWARE)
 		qdisc_put_rtab(qdisc_get_rtab(&hopt->rate, tb[TCA_HTB_RTAB],
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_ingress.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_ingress.c
@@ -80,6 +80,9 @@
 	struct net_device *dev = qdisc_dev(sch);
 	int err;
 
+	if (sch->parent != TC_H_INGRESS)
+		return -EOPNOTSUPP;
+
 	net_inc_ingress_queue();
 
 	mini_qdisc_pair_init(&q->miniqp, sch, &dev->miniq_ingress);
@@ -101,6 +104,9 @@
 {
 	struct ingress_sched_data *q = qdisc_priv(sch);
 
+	if (sch->parent != TC_H_INGRESS)
+		return;
+
 	tcf_block_put_ext(q->block, sch, &q->block_info);
 	net_dec_ingress_queue();
 }
@@ -134,7 +140,7 @@
 	.cl_ops			=	&ingress_class_ops,
 	.id			=	"ingress",
 	.priv_size		=	sizeof(struct ingress_sched_data),
-	.static_flags		=	TCQ_F_CPUSTATS,
+	.static_flags		=	TCQ_F_INGRESS | TCQ_F_CPUSTATS,
 	.init			=	ingress_init,
 	.destroy		=	ingress_destroy,
 	.dump			=	ingress_dump,
@@ -219,6 +225,9 @@
 	struct net_device *dev = qdisc_dev(sch);
 	int err;
 
+	if (sch->parent != TC_H_CLSACT)
+		return -EOPNOTSUPP;
+
 	net_inc_ingress_queue();
 	net_inc_egress_queue();
 
@@ -248,6 +257,9 @@
 {
 	struct clsact_sched_data *q = qdisc_priv(sch);
 
+	if (sch->parent != TC_H_CLSACT)
+		return;
+
 	tcf_block_put_ext(q->egress_block, sch, &q->egress_block_info);
 	tcf_block_put_ext(q->ingress_block, sch, &q->ingress_block_info);
 
@@ -269,7 +281,7 @@
 	.cl_ops			=	&clsact_class_ops,
 	.id			=	"clsact",
 	.priv_size		=	sizeof(struct clsact_sched_data),
-	.static_flags		=	TCQ_F_CPUSTATS,
+	.static_flags		=	TCQ_F_INGRESS | TCQ_F_CPUSTATS,
 	.init			=	clsact_init,
 	.destroy		=	clsact_destroy,
 	.dump			=	ingress_dump,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_mq.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_mq.c
@@ -125,6 +125,29 @@
 	priv->qdiscs = NULL;
 }
 
+static void mq_change_real_num_tx(struct Qdisc *sch, unsigned int new_real_tx)
+{
+#ifdef CONFIG_NET_SCHED
+	struct net_device *dev = qdisc_dev(sch);
+	struct Qdisc *qdisc;
+	unsigned int i;
+
+	for (i = new_real_tx; i < dev->real_num_tx_queues; i++) {
+		qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping;
+		/* Only update the default qdiscs we created,
+		 * qdiscs with handles are always hashed.
+		 */
+		if (qdisc != &noop_qdisc && !qdisc->handle)
+			qdisc_hash_del(qdisc);
+	}
+	for (i = dev->real_num_tx_queues; i < new_real_tx; i++) {
+		qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping;
+		if (qdisc != &noop_qdisc && !qdisc->handle)
+			qdisc_hash_add(qdisc, false);
+	}
+#endif
+}
+
 static int mq_dump(struct Qdisc *sch, struct sk_buff *skb)
 {
 	struct net_device *dev = qdisc_dev(sch);
@@ -288,6 +311,7 @@
 	.init		= mq_init,
 	.destroy	= mq_destroy,
 	.attach		= mq_attach,
+	.change_real_num_tx = mq_change_real_num_tx,
 	.dump		= mq_dump,
 	.owner		= THIS_MODULE,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_mqprio.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_mqprio.c
@@ -130,6 +130,97 @@
 	return 0;
 }
 
+static int mqprio_parse_nlattr(struct Qdisc *sch, struct tc_mqprio_qopt *qopt,
+			       struct nlattr *opt,
+			       struct netlink_ext_ack *extack)
+{
+	struct mqprio_sched *priv = qdisc_priv(sch);
+	struct nlattr *tb[TCA_MQPRIO_MAX + 1];
+	struct nlattr *attr;
+	int i, rem, err;
+
+	err = parse_attr(tb, TCA_MQPRIO_MAX, opt, mqprio_policy,
+			 sizeof(*qopt));
+	if (err < 0)
+		return err;
+
+	if (!qopt->hw) {
+		NL_SET_ERR_MSG(extack,
+			       "mqprio TCA_OPTIONS can only contain netlink attributes in hardware mode");
+		return -EINVAL;
+	}
+
+	if (tb[TCA_MQPRIO_MODE]) {
+		priv->flags |= TC_MQPRIO_F_MODE;
+		priv->mode = *(u16 *)nla_data(tb[TCA_MQPRIO_MODE]);
+	}
+
+	if (tb[TCA_MQPRIO_SHAPER]) {
+		priv->flags |= TC_MQPRIO_F_SHAPER;
+		priv->shaper = *(u16 *)nla_data(tb[TCA_MQPRIO_SHAPER]);
+	}
+
+	if (tb[TCA_MQPRIO_MIN_RATE64]) {
+		if (priv->shaper != TC_MQPRIO_SHAPER_BW_RATE) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[TCA_MQPRIO_MIN_RATE64],
+					    "min_rate accepted only when shaper is in bw_rlimit mode");
+			return -EINVAL;
+		}
+		i = 0;
+		nla_for_each_nested(attr, tb[TCA_MQPRIO_MIN_RATE64],
+				    rem) {
+			if (nla_type(attr) != TCA_MQPRIO_MIN_RATE64) {
+				NL_SET_ERR_MSG_ATTR(extack, attr,
+						    "Attribute type expected to be TCA_MQPRIO_MIN_RATE64");
+				return -EINVAL;
+			}
+
+			if (nla_len(attr) != sizeof(u64)) {
+				NL_SET_ERR_MSG_ATTR(extack, attr,
+						    "Attribute TCA_MQPRIO_MIN_RATE64 expected to have 8 bytes length");
+				return -EINVAL;
+			}
+
+			if (i >= qopt->num_tc)
+				break;
+			priv->min_rate[i] = *(u64 *)nla_data(attr);
+			i++;
+		}
+		priv->flags |= TC_MQPRIO_F_MIN_RATE;
+	}
+
+	if (tb[TCA_MQPRIO_MAX_RATE64]) {
+		if (priv->shaper != TC_MQPRIO_SHAPER_BW_RATE) {
+			NL_SET_ERR_MSG_ATTR(extack, tb[TCA_MQPRIO_MAX_RATE64],
+					    "max_rate accepted only when shaper is in bw_rlimit mode");
+			return -EINVAL;
+		}
+		i = 0;
+		nla_for_each_nested(attr, tb[TCA_MQPRIO_MAX_RATE64],
+				    rem) {
+			if (nla_type(attr) != TCA_MQPRIO_MAX_RATE64) {
+				NL_SET_ERR_MSG_ATTR(extack, attr,
+						    "Attribute type expected to be TCA_MQPRIO_MAX_RATE64");
+				return -EINVAL;
+			}
+
+			if (nla_len(attr) != sizeof(u64)) {
+				NL_SET_ERR_MSG_ATTR(extack, attr,
+						    "Attribute TCA_MQPRIO_MAX_RATE64 expected to have 8 bytes length");
+				return -EINVAL;
+			}
+
+			if (i >= qopt->num_tc)
+				break;
+			priv->max_rate[i] = *(u64 *)nla_data(attr);
+			i++;
+		}
+		priv->flags |= TC_MQPRIO_F_MAX_RATE;
+	}
+
+	return 0;
+}
+
 static int mqprio_init(struct Qdisc *sch, struct nlattr *opt,
 		       struct netlink_ext_ack *extack)
 {
@@ -139,9 +230,6 @@
 	struct Qdisc *qdisc;
 	int i, err = -EOPNOTSUPP;
 	struct tc_mqprio_qopt *qopt = NULL;
-	struct nlattr *tb[TCA_MQPRIO_MAX + 1];
-	struct nlattr *attr;
-	int rem;
 	int len;
 
 	BUILD_BUG_ON(TC_MAX_QUEUE != TC_QOPT_MAX_QUEUE);
@@ -166,55 +254,9 @@
 
 	len = nla_len(opt) - NLA_ALIGN(sizeof(*qopt));
 	if (len > 0) {
-		err = parse_attr(tb, TCA_MQPRIO_MAX, opt, mqprio_policy,
-				 sizeof(*qopt));
-		if (err < 0)
+		err = mqprio_parse_nlattr(sch, qopt, opt, extack);
+		if (err)
 			return err;
-
-		if (!qopt->hw)
-			return -EINVAL;
-
-		if (tb[TCA_MQPRIO_MODE]) {
-			priv->flags |= TC_MQPRIO_F_MODE;
-			priv->mode = *(u16 *)nla_data(tb[TCA_MQPRIO_MODE]);
-		}
-
-		if (tb[TCA_MQPRIO_SHAPER]) {
-			priv->flags |= TC_MQPRIO_F_SHAPER;
-			priv->shaper = *(u16 *)nla_data(tb[TCA_MQPRIO_SHAPER]);
-		}
-
-		if (tb[TCA_MQPRIO_MIN_RATE64]) {
-			if (priv->shaper != TC_MQPRIO_SHAPER_BW_RATE)
-				return -EINVAL;
-			i = 0;
-			nla_for_each_nested(attr, tb[TCA_MQPRIO_MIN_RATE64],
-					    rem) {
-				if (nla_type(attr) != TCA_MQPRIO_MIN_RATE64)
-					return -EINVAL;
-				if (i >= qopt->num_tc)
-					break;
-				priv->min_rate[i] = *(u64 *)nla_data(attr);
-				i++;
-			}
-			priv->flags |= TC_MQPRIO_F_MIN_RATE;
-		}
-
-		if (tb[TCA_MQPRIO_MAX_RATE64]) {
-			if (priv->shaper != TC_MQPRIO_SHAPER_BW_RATE)
-				return -EINVAL;
-			i = 0;
-			nla_for_each_nested(attr, tb[TCA_MQPRIO_MAX_RATE64],
-					    rem) {
-				if (nla_type(attr) != TCA_MQPRIO_MAX_RATE64)
-					return -EINVAL;
-				if (i >= qopt->num_tc)
-					break;
-				priv->max_rate[i] = *(u64 *)nla_data(attr);
-				i++;
-			}
-			priv->flags |= TC_MQPRIO_F_MAX_RATE;
-		}
 	}
 
 	/* pre-allocate qdisc, attachment can't fail */
@@ -306,6 +348,28 @@
 	priv->qdiscs = NULL;
 }
 
+static void mqprio_change_real_num_tx(struct Qdisc *sch,
+				      unsigned int new_real_tx)
+{
+	struct net_device *dev = qdisc_dev(sch);
+	struct Qdisc *qdisc;
+	unsigned int i;
+
+	for (i = new_real_tx; i < dev->real_num_tx_queues; i++) {
+		qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping;
+		/* Only update the default qdiscs we created,
+		 * qdiscs with handles are always hashed.
+		 */
+		if (qdisc != &noop_qdisc && !qdisc->handle)
+			qdisc_hash_del(qdisc);
+	}
+	for (i = dev->real_num_tx_queues; i < new_real_tx; i++) {
+		qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping;
+		if (qdisc != &noop_qdisc && !qdisc->handle)
+			qdisc_hash_add(qdisc, false);
+	}
+}
+
 static struct netdev_queue *mqprio_queue_get(struct Qdisc *sch,
 					     unsigned long cl)
 {
@@ -629,6 +693,7 @@
 	.init		= mqprio_init,
 	.destroy	= mqprio_destroy,
 	.attach		= mqprio_attach,
+	.change_real_num_tx = mqprio_change_real_num_tx,
 	.dump		= mqprio_dump,
 	.owner		= THIS_MODULE,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_multiq.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_multiq.c
@@ -152,7 +152,6 @@
 
 	for (band = 0; band < q->bands; band++)
 		qdisc_reset(q->queues[band]);
-	sch->q.qlen = 0;
 	q->curband = 0;
 }
 
@@ -186,7 +185,7 @@
 
 	qopt->bands = qdisc_dev(sch)->real_num_tx_queues;
 
-	removed = kmalloc(sizeof(*removed) * (q->max_bands - q->bands),
+	removed = kmalloc(sizeof(*removed) * (q->max_bands - qopt->bands),
 			  GFP_KERNEL);
 	if (!removed)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_netem.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_netem.c
@@ -77,6 +77,8 @@
 	struct sk_buff	*t_head;
 	struct sk_buff	*t_tail;
 
+	u32 t_len;
+
 	/* optional qdisc for classful handling (NULL at netem init) */
 	struct Qdisc	*qdisc;
 
@@ -373,6 +375,7 @@
 	rtnl_kfree_skbs(q->t_head, q->t_tail);
 	q->t_head = NULL;
 	q->t_tail = NULL;
+	q->t_len = 0;
 }
 
 static void tfifo_enqueue(struct sk_buff *nskb, struct Qdisc *sch)
@@ -402,6 +405,7 @@
 		rb_link_node(&nskb->rbnode, parent, p);
 		rb_insert_color(&nskb->rbnode, &q->t_root);
 	}
+	q->t_len++;
 	sch->q.qlen++;
 }
 
@@ -437,12 +441,10 @@
 	struct netem_sched_data *q = qdisc_priv(sch);
 	/* We don't fill cb now as skb_unshare() may invalidate it */
 	struct netem_skb_cb *cb;
-	struct sk_buff *skb2;
+	struct sk_buff *skb2 = NULL;
 	struct sk_buff *segs = NULL;
 	unsigned int prev_len = qdisc_pkt_len(skb);
 	int count = 1;
-	int rc = NET_XMIT_SUCCESS;
-	int rc_drop = NET_XMIT_DROP;
 
 	/* Do not fool qdisc_drop_all() */
 	skb->prev = NULL;
@@ -471,19 +473,11 @@
 		skb_orphan_partial(skb);
 
 	/*
-	 * If we need to duplicate packet, then re-insert at top of the
-	 * qdisc tree, since parent queuer expects that only one
-	 * skb will be queued.
+	 * If we need to duplicate packet, then clone it before
+	 * original is modified.
 	 */
-	if (count > 1 && (skb2 = skb_clone(skb, GFP_ATOMIC)) != NULL) {
-		struct Qdisc *rootq = qdisc_root_bh(sch);
-		u32 dupsave = q->duplicate; /* prevent duplicating a dup... */
-
-		q->duplicate = 0;
-		rootq->enqueue(skb2, rootq, to_free);
-		q->duplicate = dupsave;
-		rc_drop = NET_XMIT_SUCCESS;
-	}
+	if (count > 1)
+		skb2 = skb_clone(skb, GFP_ATOMIC);
 
 	/*
 	 * Randomized packet corruption.
@@ -495,7 +489,8 @@
 		if (skb_is_gso(skb)) {
 			skb = netem_segment(skb, sch, to_free);
 			if (!skb)
-				return rc_drop;
+				goto finish_segs;
+
 			segs = skb->next;
 			skb_mark_not_on_list(skb);
 			qdisc_skb_cb(skb)->pkt_len = skb->len;
@@ -517,11 +512,28 @@
 			1<<(prandom_u32() % 8);
 	}
 
-	if (unlikely(sch->q.qlen >= sch->limit)) {
+	if (unlikely(q->t_len >= sch->limit)) {
 		/* re-link segs, so that qdisc_drop_all() frees them all */
 		skb->next = segs;
 		qdisc_drop_all(skb, sch, to_free);
-		return rc_drop;
+		if (skb2)
+			__qdisc_drop(skb2, to_free);
+		return NET_XMIT_DROP;
+	}
+
+	/*
+	 * If doing duplication then re-insert at top of the
+	 * qdisc tree, since parent queuer expects that only one
+	 * skb will be queued.
+	 */
+	if (skb2) {
+		struct Qdisc *rootq = qdisc_root_bh(sch);
+		u32 dupsave = q->duplicate; /* prevent duplicating a dup... */
+
+		q->duplicate = 0;
+		rootq->enqueue(skb2, rootq, to_free);
+		q->duplicate = dupsave;
+		skb2 = NULL;
 	}
 
 	qdisc_qstats_backlog_inc(sch, skb);
@@ -592,9 +604,12 @@
 	}
 
 finish_segs:
+	if (skb2)
+		__qdisc_drop(skb2, to_free);
+
 	if (segs) {
 		unsigned int len, last_len;
-		int nb;
+		int rc, nb;
 
 		len = skb ? skb->len : 0;
 		nb = skb ? 1 : 0;
@@ -681,8 +696,8 @@
 tfifo_dequeue:
 	skb = __qdisc_dequeue_head(&sch->q);
 	if (skb) {
-		qdisc_qstats_backlog_dec(sch, skb);
 deliver:
+		qdisc_qstats_backlog_dec(sch, skb);
 		qdisc_bstats_update(sch, skb);
 		return skb;
 	}
@@ -698,8 +713,7 @@
 
 		if (time_to_send <= now && q->slot.slot_next <= now) {
 			netem_erase_head(q, skb);
-			sch->q.qlen--;
-			qdisc_qstats_backlog_dec(sch, skb);
+			q->t_len--;
 			skb->next = NULL;
 			skb->prev = NULL;
 			/* skb->dev shares skb->rbnode area,
@@ -722,21 +736,25 @@
 
 				err = qdisc_enqueue(skb, q->qdisc, &to_free);
 				kfree_skb_list(to_free);
-				if (err != NET_XMIT_SUCCESS &&
-				    net_xmit_drop_count(err)) {
-					qdisc_qstats_drop(sch);
-					qdisc_tree_reduce_backlog(sch, 1,
-								  pkt_len);
+				if (err != NET_XMIT_SUCCESS) {
+					if (net_xmit_drop_count(err))
+						qdisc_qstats_drop(sch);
+					sch->qstats.backlog -= pkt_len;
+					sch->q.qlen--;
+					qdisc_tree_reduce_backlog(sch, 1, pkt_len);
 				}
 				goto tfifo_dequeue;
 			}
+			sch->q.qlen--;
 			goto deliver;
 		}
 
 		if (q->qdisc) {
 			skb = q->qdisc->ops->dequeue(q->qdisc);
-			if (skb)
+			if (skb) {
+				sch->q.qlen--;
 				goto deliver;
+			}
 		}
 
 		qdisc_watchdog_schedule_ns(&q->watchdog,
@@ -746,8 +764,10 @@
 
 	if (q->qdisc) {
 		skb = q->qdisc->ops->dequeue(q->qdisc);
-		if (skb)
+		if (skb) {
+			sch->q.qlen--;
 			goto deliver;
+		}
 	}
 	return NULL;
 }
@@ -773,12 +793,10 @@
  * signed 16 bit values.
  */
 
-static int get_dist_table(struct Qdisc *sch, struct disttable **tbl,
-			  const struct nlattr *attr)
+static int get_dist_table(struct disttable **tbl, const struct nlattr *attr)
 {
 	size_t n = nla_len(attr)/sizeof(__s16);
 	const __s16 *data = nla_data(attr);
-	spinlock_t *root_lock;
 	struct disttable *d;
 	int i;
 
@@ -793,13 +811,7 @@
 	for (i = 0; i < n; i++)
 		d->table[i] = data[i];
 
-	root_lock = qdisc_root_sleeping_lock(sch);
-
-	spin_lock_bh(root_lock);
-	swap(*tbl, d);
-	spin_unlock_bh(root_lock);
-
-	dist_free(d);
+	*tbl = d;
 	return 0;
 }
 
@@ -956,6 +968,8 @@
 {
 	struct netem_sched_data *q = qdisc_priv(sch);
 	struct nlattr *tb[TCA_NETEM_MAX + 1];
+	struct disttable *delay_dist = NULL;
+	struct disttable *slot_dist = NULL;
 	struct tc_netem_qopt *qopt;
 	struct clgstate old_clg;
 	int old_loss_model = CLG_RANDOM;
@@ -969,6 +983,19 @@
 	if (ret < 0)
 		return ret;
 
+	if (tb[TCA_NETEM_DELAY_DIST]) {
+		ret = get_dist_table(&delay_dist, tb[TCA_NETEM_DELAY_DIST]);
+		if (ret)
+			goto table_free;
+	}
+
+	if (tb[TCA_NETEM_SLOT_DIST]) {
+		ret = get_dist_table(&slot_dist, tb[TCA_NETEM_SLOT_DIST]);
+		if (ret)
+			goto table_free;
+	}
+
+	sch_tree_lock(sch);
 	/* backup q->clg and q->loss_model */
 	old_clg = q->clg;
 	old_loss_model = q->loss_model;
@@ -977,26 +1004,17 @@
 		ret = get_loss_clg(q, tb[TCA_NETEM_LOSS]);
 		if (ret) {
 			q->loss_model = old_loss_model;
-			return ret;
+			q->clg = old_clg;
+			goto unlock;
 		}
 	} else {
 		q->loss_model = CLG_RANDOM;
 	}
 
-	if (tb[TCA_NETEM_DELAY_DIST]) {
-		ret = get_dist_table(sch, &q->delay_dist,
-				     tb[TCA_NETEM_DELAY_DIST]);
-		if (ret)
-			goto get_table_failure;
-	}
-
-	if (tb[TCA_NETEM_SLOT_DIST]) {
-		ret = get_dist_table(sch, &q->slot_dist,
-				     tb[TCA_NETEM_SLOT_DIST]);
-		if (ret)
-			goto get_table_failure;
-	}
-
+	if (delay_dist)
+		swap(q->delay_dist, delay_dist);
+	if (slot_dist)
+		swap(q->slot_dist, slot_dist);
 	sch->limit = qopt->limit;
 
 	q->latency = PSCHED_TICKS2NS(qopt->latency);
@@ -1044,15 +1062,12 @@
 	/* capping jitter to the range acceptable by tabledist() */
 	q->jitter = min_t(s64, abs(q->jitter), INT_MAX);
 
-	return ret;
+unlock:
+	sch_tree_unlock(sch);
 
-get_table_failure:
-	/* recover clg and loss_model, in case of
-	 * q->clg and q->loss_model were modified
-	 * in get_loss_clg()
-	 */
-	q->clg = old_clg;
-	q->loss_model = old_loss_model;
+table_free:
+	dist_free(delay_dist);
+	dist_free(slot_dist);
 	return ret;
 }
 
@@ -1146,9 +1161,9 @@
 	struct tc_netem_rate rate;
 	struct tc_netem_slot slot;
 
-	qopt.latency = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->latency),
+	qopt.latency = min_t(psched_time_t, PSCHED_NS2TICKS(q->latency),
 			     UINT_MAX);
-	qopt.jitter = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->jitter),
+	qopt.jitter = min_t(psched_time_t, PSCHED_NS2TICKS(q->jitter),
 			    UINT_MAX);
 	qopt.limit = q->limit;
 	qopt.loss = q->loss;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_plug.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_plug.c
@@ -210,7 +210,7 @@
 	.priv_size   =       sizeof(struct plug_sched_data),
 	.enqueue     =       plug_enqueue,
 	.dequeue     =       plug_dequeue,
-	.peek        =       qdisc_peek_head,
+	.peek        =       qdisc_peek_dequeued,
 	.init        =       plug_init,
 	.change      =       plug_change,
 	.reset       =	     qdisc_reset_queue,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_prio.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_prio.c
@@ -135,8 +135,6 @@
 
 	for (prio = 0; prio < q->bands; prio++)
 		qdisc_reset(q->queues[prio]);
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 }
 
 static int prio_offload(struct Qdisc *sch, struct tc_prio_qopt *qopt)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_qfq.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_qfq.c
@@ -113,6 +113,7 @@
 
 #define QFQ_MTU_SHIFT		16	/* to support TSO/GSO */
 #define QFQ_MIN_LMAX		512	/* see qfq_slot_insert */
+#define QFQ_MAX_LMAX		(1UL << QFQ_MTU_SHIFT)
 
 #define QFQ_MAX_AGG_CLASSES	8 /* max num classes per aggregate allowed */
 
@@ -214,9 +215,14 @@
 	return container_of(clc, struct qfq_class, common);
 }
 
+static struct netlink_range_validation lmax_range = {
+	.min = QFQ_MIN_LMAX,
+	.max = QFQ_MAX_LMAX,
+};
+
 static const struct nla_policy qfq_policy[TCA_QFQ_MAX + 1] = {
-	[TCA_QFQ_WEIGHT] = { .type = NLA_U32 },
-	[TCA_QFQ_LMAX] = { .type = NLA_U32 },
+	[TCA_QFQ_WEIGHT] = NLA_POLICY_RANGE(NLA_U32, 1, QFQ_MAX_WEIGHT),
+	[TCA_QFQ_LMAX] = NLA_POLICY_FULL_RANGE(NLA_U32, &lmax_range),
 };
 
 /*
@@ -375,8 +381,13 @@
 			   u32 lmax)
 {
 	struct qfq_sched *q = qdisc_priv(sch);
-	struct qfq_aggregate *new_agg = qfq_find_agg(q, lmax, weight);
+	struct qfq_aggregate *new_agg;
+
+	/* 'lmax' can range from [QFQ_MIN_LMAX, pktlen + stab overhead] */
+	if (lmax > QFQ_MAX_LMAX)
+		return -EINVAL;
 
+	new_agg = qfq_find_agg(q, lmax, weight);
 	if (new_agg == NULL) { /* create new aggregate */
 		new_agg = kzalloc(sizeof(*new_agg), GFP_ATOMIC);
 		if (new_agg == NULL)
@@ -408,27 +419,26 @@
 	}
 
 	err = nla_parse_nested_deprecated(tb, TCA_QFQ_MAX, tca[TCA_OPTIONS],
-					  qfq_policy, NULL);
+					  qfq_policy, extack);
 	if (err < 0)
 		return err;
 
-	if (tb[TCA_QFQ_WEIGHT]) {
+	if (tb[TCA_QFQ_WEIGHT])
 		weight = nla_get_u32(tb[TCA_QFQ_WEIGHT]);
-		if (!weight || weight > (1UL << QFQ_MAX_WSHIFT)) {
-			pr_notice("qfq: invalid weight %u\n", weight);
-			return -EINVAL;
-		}
-	} else
+	else
 		weight = 1;
 
 	if (tb[TCA_QFQ_LMAX]) {
 		lmax = nla_get_u32(tb[TCA_QFQ_LMAX]);
-		if (lmax < QFQ_MIN_LMAX || lmax > (1UL << QFQ_MTU_SHIFT)) {
-			pr_notice("qfq: invalid max length %u\n", lmax);
+	} else {
+		/* MTU size is user controlled */
+		lmax = psched_mtu(qdisc_dev(sch));
+		if (lmax < QFQ_MIN_LMAX || lmax > QFQ_MAX_LMAX) {
+			NL_SET_ERR_MSG_MOD(extack,
+					   "MTU size out of bounds for qfq");
 			return -EINVAL;
 		}
-	} else
-		lmax = psched_mtu(qdisc_dev(sch));
+	}
 
 	inv_w = ONE_FP / weight;
 	weight = ONE_FP / inv_w;
@@ -970,10 +980,13 @@
 }
 
 /* Dequeue head packet of the head class in the DRR queue of the aggregate. */
-static void agg_dequeue(struct qfq_aggregate *agg,
-			struct qfq_class *cl, unsigned int len)
+static struct sk_buff *agg_dequeue(struct qfq_aggregate *agg,
+				   struct qfq_class *cl, unsigned int len)
 {
-	qdisc_dequeue_peeked(cl->qdisc);
+	struct sk_buff *skb = qdisc_dequeue_peeked(cl->qdisc);
+
+	if (!skb)
+		return NULL;
 
 	cl->deficit -= (int) len;
 
@@ -983,6 +996,8 @@
 		cl->deficit += agg->lmax;
 		list_move_tail(&cl->alist, &agg->active);
 	}
+
+	return skb;
 }
 
 static inline struct sk_buff *qfq_peek_skb(struct qfq_aggregate *agg,
@@ -1128,11 +1143,18 @@
 	if (!skb)
 		return NULL;
 
-	qdisc_qstats_backlog_dec(sch, skb);
 	sch->q.qlen--;
+
+	skb = agg_dequeue(in_serv_agg, cl, len);
+
+	if (!skb) {
+		sch->q.qlen++;
+		return NULL;
+	}
+
+	qdisc_qstats_backlog_dec(sch, skb);
 	qdisc_bstats_update(sch, skb);
 
-	agg_dequeue(in_serv_agg, cl, len);
 	/* If lmax is lowered, through qfq_change_class, for a class
 	 * owning pending packets with larger size than the new value
 	 * of lmax, then the following condition may hold.
@@ -1422,10 +1444,8 @@
 	if (err < 0)
 		return err;
 
-	if (qdisc_dev(sch)->tx_queue_len + 1 > QFQ_MAX_AGG_CLASSES)
-		max_classes = QFQ_MAX_AGG_CLASSES;
-	else
-		max_classes = qdisc_dev(sch)->tx_queue_len + 1;
+	max_classes = min_t(u64, (u64)qdisc_dev(sch)->tx_queue_len + 1,
+			    QFQ_MAX_AGG_CLASSES);
 	/* max_cl_shift = floor(log_2(max_classes)) */
 	max_cl_shift = __fls(max_classes);
 	q->max_agg_classes = 1<<max_cl_shift;
@@ -1461,8 +1481,6 @@
 			qdisc_reset(cl->qdisc);
 		}
 	}
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 }
 
 static void qfq_destroy_qdisc(struct Qdisc *sch)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_red.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_red.c
@@ -72,6 +72,7 @@
 {
 	struct red_sched_data *q = qdisc_priv(sch);
 	struct Qdisc *child = q->qdisc;
+	unsigned int len;
 	int ret;
 
 	q->vars.qavg = red_calc_qavg(&q->parms,
@@ -126,9 +127,10 @@
 		break;
 	}
 
+	len = qdisc_pkt_len(skb);
 	ret = qdisc_enqueue(skb, child, to_free);
 	if (likely(ret == NET_XMIT_SUCCESS)) {
-		qdisc_qstats_backlog_inc(sch, skb);
+		sch->qstats.backlog += len;
 		sch->q.qlen++;
 	} else if (net_xmit_drop_count(ret)) {
 		q->stats.pdrop++;
@@ -176,8 +178,6 @@
 	struct red_sched_data *q = qdisc_priv(sch);
 
 	qdisc_reset(q->qdisc);
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 	red_restart(&q->vars);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_sfb.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_sfb.c
@@ -135,15 +135,15 @@
 	}
 }
 
-static void increment_qlen(const struct sk_buff *skb, struct sfb_sched_data *q)
+static void increment_qlen(const struct sfb_skb_cb *cb, struct sfb_sched_data *q)
 {
 	u32 sfbhash;
 
-	sfbhash = sfb_hash(skb, 0);
+	sfbhash = cb->hashes[0];
 	if (sfbhash)
 		increment_one_qlen(sfbhash, 0, q);
 
-	sfbhash = sfb_hash(skb, 1);
+	sfbhash = cb->hashes[1];
 	if (sfbhash)
 		increment_one_qlen(sfbhash, 1, q);
 }
@@ -281,8 +281,10 @@
 {
 
 	struct sfb_sched_data *q = qdisc_priv(sch);
+	unsigned int len = qdisc_pkt_len(skb);
 	struct Qdisc *child = q->qdisc;
 	struct tcf_proto *fl;
+	struct sfb_skb_cb cb;
 	int i;
 	u32 p_min = ~0;
 	u32 minqlen = ~0;
@@ -399,11 +401,12 @@
 	}
 
 enqueue:
+	memcpy(&cb, sfb_skb_cb(skb), sizeof(cb));
 	ret = qdisc_enqueue(skb, child, to_free);
 	if (likely(ret == NET_XMIT_SUCCESS)) {
-		qdisc_qstats_backlog_inc(sch, skb);
+		sch->qstats.backlog += len;
 		sch->q.qlen++;
-		increment_qlen(skb, q);
+		increment_qlen(&cb, q);
 	} else if (net_xmit_drop_count(ret)) {
 		q->stats.childdrop++;
 		qdisc_qstats_drop(sch);
@@ -452,9 +455,8 @@
 {
 	struct sfb_sched_data *q = qdisc_priv(sch);
 
-	qdisc_reset(q->qdisc);
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
+	if (likely(q->qdisc))
+		qdisc_reset(q->qdisc);
 	q->slot = 0;
 	q->double_buffering = false;
 	sfb_zero_all_buckets(q);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_skbprio.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_skbprio.c
@@ -121,8 +121,6 @@
 	/* Check to update highest and lowest priorities. */
 	if (skb_queue_empty(lp_qdisc)) {
 		if (q->lowest_prio == q->highest_prio) {
-			/* The incoming packet is the only packet in queue. */
-			BUG_ON(sch->q.qlen != 1);
 			q->lowest_prio = prio;
 			q->highest_prio = prio;
 		} else {
@@ -154,7 +152,6 @@
 	/* Update highest priority field. */
 	if (skb_queue_empty(hpq)) {
 		if (q->lowest_prio == q->highest_prio) {
-			BUG_ON(sch->q.qlen);
 			q->highest_prio = 0;
 			q->lowest_prio = SKBPRIO_MAX_PRIORITY - 1;
 		} else {
@@ -213,9 +210,6 @@
 	struct skbprio_sched_data *q = qdisc_priv(sch);
 	int prio;
 
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
-
 	for (prio = 0; prio < SKBPRIO_MAX_PRIORITY; prio++)
 		__skb_queue_purge(&q->qdiscs[prio]);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_taprio.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_taprio.c
@@ -66,6 +66,7 @@
 	u32 flags;
 	enum tk_offsets tk_offset;
 	int clockid;
+	bool offloaded;
 	atomic64_t picos_per_byte; /* Using picoseconds because for 10Gbps+
 				    * speeds it's sub-nanoseconds per byte
 				    */
@@ -95,18 +96,22 @@
 	return ns_to_ktime(sched->base_time);
 }
 
-static ktime_t taprio_get_time(struct taprio_sched *q)
+static ktime_t taprio_mono_to_any(const struct taprio_sched *q, ktime_t mono)
 {
-	ktime_t mono = ktime_get();
+	/* This pairs with WRITE_ONCE() in taprio_parse_clockid() */
+	enum tk_offsets tk_offset = READ_ONCE(q->tk_offset);
 
-	switch (q->tk_offset) {
+	switch (tk_offset) {
 	case TK_OFFS_MAX:
 		return mono;
 	default:
-		return ktime_mono_to_any(mono, q->tk_offset);
+		return ktime_mono_to_any(mono, tk_offset);
 	}
+}
 
-	return KTIME_MAX;
+static ktime_t taprio_get_time(const struct taprio_sched *q)
+{
+	return taprio_mono_to_any(q, ktime_get());
 }
 
 static void taprio_free_sched_cb(struct rcu_head *head)
@@ -319,7 +324,7 @@
 		return 0;
 	}
 
-	return ktime_mono_to_any(skb->skb_mstamp_ns, q->tk_offset);
+	return taprio_mono_to_any(q, skb->skb_mstamp_ns);
 }
 
 /* There are a few scenarios where we will have to modify the txtime from
@@ -413,7 +418,8 @@
 {
 	struct taprio_sched *q = qdisc_priv(sch);
 
-	if (skb->sk && sock_flag(skb->sk, SOCK_TXTIME)) {
+	/* sk_flags are only safe to use on full sockets. */
+	if (skb->sk && sk_fullsock(skb->sk) && sock_flag(skb->sk, SOCK_TXTIME)) {
 		if (!is_valid_interval(skb, sch))
 			return qdisc_drop(skb, sch, to_free);
 	} else if (TXTIME_ASSIST_IS_ENABLED(q->flags)) {
@@ -774,6 +780,11 @@
 	[TCA_TAPRIO_SCHED_ENTRY_INTERVAL]  = { .type = NLA_U32 },
 };
 
+static struct netlink_range_validation_signed taprio_cycle_time_range = {
+	.min = 0,
+	.max = INT_MAX,
+};
+
 static const struct nla_policy taprio_policy[TCA_TAPRIO_ATTR_MAX + 1] = {
 	[TCA_TAPRIO_ATTR_PRIOMAP]	       = {
 		.len = sizeof(struct tc_mqprio_qopt)
@@ -782,7 +793,8 @@
 	[TCA_TAPRIO_ATTR_SCHED_BASE_TIME]            = { .type = NLA_S64 },
 	[TCA_TAPRIO_ATTR_SCHED_SINGLE_ENTRY]         = { .type = NLA_NESTED },
 	[TCA_TAPRIO_ATTR_SCHED_CLOCKID]              = { .type = NLA_S32 },
-	[TCA_TAPRIO_ATTR_SCHED_CYCLE_TIME]           = { .type = NLA_S64 },
+	[TCA_TAPRIO_ATTR_SCHED_CYCLE_TIME]           =
+		NLA_POLICY_FULL_RANGE_SIGNED(NLA_S64, &taprio_cycle_time_range),
 	[TCA_TAPRIO_ATTR_SCHED_CYCLE_TIME_EXTENSION] = { .type = NLA_S64 },
 	[TCA_TAPRIO_ATTR_FLAGS]                      = { .type = NLA_U32 },
 	[TCA_TAPRIO_ATTR_TXTIME_DELAY]		     = { .type = NLA_U32 },
@@ -917,6 +929,11 @@
 			return -EINVAL;
 		}
 
+		if (cycle < 0 || cycle > INT_MAX) {
+			NL_SET_ERR_MSG(extack, "'cycle_time' is too big");
+			return -EINVAL;
+		}
+
 		new->cycle_time = cycle;
 	}
 
@@ -930,16 +947,13 @@
 {
 	int i, j;
 
-	if (!qopt && !dev->num_tc) {
-		NL_SET_ERR_MSG(extack, "'mqprio' configuration is necessary");
-		return -EINVAL;
-	}
-
-	/* If num_tc is already set, it means that the user already
-	 * configured the mqprio part
-	 */
-	if (dev->num_tc)
+	if (!qopt) {
+		if (!dev->num_tc) {
+			NL_SET_ERR_MSG(extack, "'mqprio' configuration is necessary");
+			return -EINVAL;
+		}
 		return 0;
+	}
 
 	/* Verify num_tc is not out of max range */
 	if (qopt->num_tc > TC_MAX_QUEUE) {
@@ -1121,7 +1135,7 @@
 			 struct sched_gate_list *sched, ktime_t base)
 {
 	struct sched_entry *entry;
-	u32 interval = 0;
+	u64 interval = 0;
 
 	list_for_each_entry(entry, &sched->entries, list) {
 		entry->next_txtime = ktime_add_ns(base, interval);
@@ -1273,6 +1287,8 @@
 		goto done;
 	}
 
+	q->offloaded = true;
+
 done:
 	taprio_offload_free(offload);
 
@@ -1287,12 +1303,9 @@
 	struct tc_taprio_qopt_offload *offload;
 	int err;
 
-	if (!FULL_OFFLOAD_IS_ENABLED(q->flags))
+	if (!q->offloaded)
 		return 0;
 
-	if (!ops->ndo_setup_tc)
-		return -EOPNOTSUPP;
-
 	offload = taprio_offload_alloc(0);
 	if (!offload) {
 		NL_SET_ERR_MSG(extack,
@@ -1308,6 +1321,8 @@
 		goto out;
 	}
 
+	q->offloaded = false;
+
 out:
 	taprio_offload_free(offload);
 
@@ -1352,6 +1367,7 @@
 		}
 	} else if (tb[TCA_TAPRIO_ATTR_SCHED_CLOCKID]) {
 		int clockid = nla_get_s32(tb[TCA_TAPRIO_ATTR_SCHED_CLOCKID]);
+		enum tk_offsets tk_offset;
 
 		/* We only support static clockids and we don't allow
 		 * for it to be modified after the first init.
@@ -1366,22 +1382,24 @@
 
 		switch (clockid) {
 		case CLOCK_REALTIME:
-			q->tk_offset = TK_OFFS_REAL;
+			tk_offset = TK_OFFS_REAL;
 			break;
 		case CLOCK_MONOTONIC:
-			q->tk_offset = TK_OFFS_MAX;
+			tk_offset = TK_OFFS_MAX;
 			break;
 		case CLOCK_BOOTTIME:
-			q->tk_offset = TK_OFFS_BOOT;
+			tk_offset = TK_OFFS_BOOT;
 			break;
 		case CLOCK_TAI:
-			q->tk_offset = TK_OFFS_TAI;
+			tk_offset = TK_OFFS_TAI;
 			break;
 		default:
 			NL_SET_ERR_MSG(extack, "Invalid 'clockid'");
 			err = -EINVAL;
 			goto out;
 		}
+		/* This pairs with READ_ONCE() in taprio_mono_to_any */
+		WRITE_ONCE(q->tk_offset, tk_offset);
 
 		q->clockid = clockid;
 	} else {
@@ -1581,7 +1599,9 @@
 			goto unlock;
 		}
 
-		rcu_assign_pointer(q->admin_sched, new_admin);
+		/* Not going to race against advance_sched(), but still */
+		admin = rcu_replace_pointer(q->admin_sched, new_admin,
+					    lockdep_rtnl_is_held());
 		if (admin)
 			call_rcu(&admin->rcu, taprio_free_sched_cb);
 	} else {
@@ -1592,7 +1612,8 @@
 
 		taprio_start_sched(sch, start, new_admin);
 
-		rcu_assign_pointer(q->admin_sched, new_admin);
+		admin = rcu_replace_pointer(q->admin_sched, new_admin,
+					    lockdep_rtnl_is_held());
 		if (admin)
 			call_rcu(&admin->rcu, taprio_free_sched_cb);
 
@@ -1622,13 +1643,12 @@
 	int i;
 
 	hrtimer_cancel(&q->advance_timer);
+
 	if (q->qdiscs) {
 		for (i = 0; i < dev->num_tx_queues; i++)
 			if (q->qdiscs[i])
 				qdisc_reset(q->qdiscs[i]);
 	}
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 }
 
 static void taprio_destroy(struct Qdisc *sch)
@@ -1645,6 +1665,7 @@
 	 * happens in qdisc_create(), after taprio_init() has been called.
 	 */
 	hrtimer_cancel(&q->advance_timer);
+	qdisc_synchronize(sch);
 
 	taprio_disable_offload(dev, q, NULL);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_tbf.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_tbf.c
@@ -193,7 +193,7 @@
 	struct tbf_sched_data *q = qdisc_priv(sch);
 	struct sk_buff *segs, *nskb;
 	netdev_features_t features = netif_skb_features(skb);
-	unsigned int len = 0, prev_len = qdisc_pkt_len(skb);
+	unsigned int len = 0, prev_len = qdisc_pkt_len(skb), seg_len;
 	int ret, nb;
 
 	segs = skb_gso_segment(skb, features & ~NETIF_F_GSO_MASK);
@@ -204,21 +204,27 @@
 	nb = 0;
 	skb_list_walk_safe(segs, segs, nskb) {
 		skb_mark_not_on_list(segs);
-		qdisc_skb_cb(segs)->pkt_len = segs->len;
-		len += segs->len;
+		seg_len = segs->len;
+		qdisc_skb_cb(segs)->pkt_len = seg_len;
 		ret = qdisc_enqueue(segs, q->qdisc, to_free);
 		if (ret != NET_XMIT_SUCCESS) {
 			if (net_xmit_drop_count(ret))
 				qdisc_qstats_drop(sch);
 		} else {
 			nb++;
+			len += seg_len;
 		}
 	}
 	sch->q.qlen += nb;
-	if (nb > 1)
+	sch->qstats.backlog += len;
+	if (nb > 0) {
 		qdisc_tree_reduce_backlog(sch, 1 - nb, prev_len - len);
-	consume_skb(skb);
-	return nb > 0 ? NET_XMIT_SUCCESS : NET_XMIT_DROP;
+		consume_skb(skb);
+		return NET_XMIT_SUCCESS;
+	}
+
+	kfree_skb(skb);
+	return NET_XMIT_DROP;
 }
 
 static int tbf_enqueue(struct sk_buff *skb, struct Qdisc *sch,
@@ -316,8 +322,6 @@
 	struct tbf_sched_data *q = qdisc_priv(sch);
 
 	qdisc_reset(q->qdisc);
-	sch->qstats.backlog = 0;
-	sch->q.qlen = 0;
 	q->t_c = ktime_get_ns();
 	q->tokens = q->buffer;
 	q->ptokens = q->mtu;
@@ -342,6 +346,7 @@
 	struct nlattr *tb[TCA_TBF_MAX + 1];
 	struct tc_tbf_qopt *qopt;
 	struct Qdisc *child = NULL;
+	struct Qdisc *old = NULL;
 	struct psched_ratecfg rate;
 	struct psched_ratecfg peak;
 	u64 max_size;
@@ -433,7 +438,7 @@
 	sch_tree_lock(sch);
 	if (child) {
 		qdisc_tree_flush_backlog(q->qdisc);
-		qdisc_put(q->qdisc);
+		old = q->qdisc;
 		q->qdisc = child;
 	}
 	q->limit = qopt->limit;
@@ -453,6 +458,7 @@
 	memcpy(&q->peak, &peak, sizeof(struct psched_ratecfg));
 
 	sch_tree_unlock(sch);
+	qdisc_put(old);
 	err = 0;
 
 	tbf_offload_change(sch);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sched/sch_teql.c
+++ linux-xilinx-zynqmp-5.15.0/net/sched/sch_teql.c
@@ -124,7 +124,6 @@
 	struct teql_sched_data *dat = qdisc_priv(sch);
 
 	skb_queue_purge(&dat->q);
-	sch->q.qlen = 0;
 }
 
 static void
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/associola.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/associola.c
@@ -137,7 +137,8 @@
 		= 5 * asoc->rto_max;
 
 	asoc->timeouts[SCTP_EVENT_TIMEOUT_SACK] = asoc->sackdelay;
-	asoc->timeouts[SCTP_EVENT_TIMEOUT_AUTOCLOSE] = sp->autoclose * HZ;
+	asoc->timeouts[SCTP_EVENT_TIMEOUT_AUTOCLOSE] =
+		(unsigned long)sp->autoclose * HZ;
 
 	/* Initializes the timers */
 	for (i = SCTP_EVENT_TIMEOUT_NONE; i < SCTP_NUM_TIMEOUT_TYPES; ++i)
@@ -229,9 +230,8 @@
 	if (!sctp_ulpq_init(&asoc->ulpq, asoc))
 		goto fail_init;
 
-	if (sctp_stream_init(&asoc->stream, asoc->c.sinit_num_ostreams,
-			     0, gfp))
-		goto fail_init;
+	if (sctp_stream_init(&asoc->stream, asoc->c.sinit_num_ostreams, 0, gfp))
+		goto stream_free;
 
 	/* Initialize default path MTU. */
 	asoc->pathmtu = sp->pathmtu;
@@ -1162,8 +1162,7 @@
 		/* Add any peer addresses from the new association. */
 		list_for_each_entry(trans, &new->peer.transport_addr_list,
 				    transports)
-			if (!sctp_assoc_lookup_paddr(asoc, &trans->ipaddr) &&
-			    !sctp_assoc_add_peer(asoc, &trans->ipaddr,
+			if (!sctp_assoc_add_peer(asoc, &trans->ipaddr,
 						 GFP_ATOMIC, trans->state))
 				return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/auth.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/auth.c
@@ -863,12 +863,17 @@
 	}
 
 	list_del_init(&shkey->key_list);
-	sctp_auth_shkey_release(shkey);
 	list_add(&cur_key->key_list, sh_keys);
 
-	if (asoc && asoc->active_key_id == auth_key->sca_keynumber)
-		sctp_auth_asoc_init_active_key(asoc, GFP_KERNEL);
+	if (asoc && asoc->active_key_id == auth_key->sca_keynumber &&
+	    sctp_auth_asoc_init_active_key(asoc, GFP_KERNEL)) {
+		list_del_init(&cur_key->key_list);
+		sctp_auth_shkey_release(cur_key);
+		list_add(&shkey->key_list, sh_keys);
+		return -ENOMEM;
+	}
 
+	sctp_auth_shkey_release(shkey);
 	return 0;
 }
 
@@ -902,8 +907,13 @@
 		return -EINVAL;
 
 	if (asoc) {
+		__u16  active_key_id = asoc->active_key_id;
+
 		asoc->active_key_id = key_id;
-		sctp_auth_asoc_init_active_key(asoc, GFP_KERNEL);
+		if (sctp_auth_asoc_init_active_key(asoc, GFP_KERNEL)) {
+			asoc->active_key_id = active_key_id;
+			return -ENOMEM;
+		}
 	} else
 		ep->active_key_id = key_id;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/bind_addr.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/bind_addr.c
@@ -73,6 +73,12 @@
 		}
 	}
 
+	/* If somehow no addresses were found that can be used with this
+	 * scope, it's an error.
+	 */
+	if (list_empty(&dest->address_list))
+		error = -ENETUNREACH;
+
 out:
 	if (error)
 		sctp_bind_addr_clean(dest);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/diag.c
@@ -61,10 +61,6 @@
 		r->idiag_timer = SCTP_EVENT_TIMEOUT_T3_RTX;
 		r->idiag_retrans = asoc->rtx_data_chunks;
 		r->idiag_expires = jiffies_to_msecs(t3_rtx->expires - jiffies);
-	} else {
-		r->idiag_timer = 0;
-		r->idiag_retrans = 0;
-		r->idiag_expires = 0;
 	}
 }
 
@@ -144,13 +140,14 @@
 	r = nlmsg_data(nlh);
 	BUG_ON(!sk_fullsock(sk));
 
+	r->idiag_timer = 0;
+	r->idiag_retrans = 0;
+	r->idiag_expires = 0;
 	if (asoc) {
 		inet_diag_msg_sctpasoc_fill(r, sk, asoc);
 	} else {
 		inet_diag_msg_common_fill(r, sk);
 		r->idiag_state = sk->sk_state;
-		r->idiag_timer = 0;
-		r->idiag_retrans = 0;
 	}
 
 	if (inet_diag_msg_attrs_fill(sk, skb, r, ext, user_ns, net_admin))
@@ -245,54 +242,49 @@
 		+ 64;
 }
 
-static int sctp_tsp_dump_one(struct sctp_transport *tsp, void *p)
+static int sctp_sock_dump_one(struct sctp_endpoint *ep, struct sctp_transport *tsp, void *p)
 {
 	struct sctp_association *assoc = tsp->asoc;
-	struct sock *sk = tsp->asoc->base.sk;
 	struct sctp_comm_param *commp = p;
-	struct sk_buff *in_skb = commp->skb;
+	struct sock *sk = ep->base.sk;
 	const struct inet_diag_req_v2 *req = commp->r;
-	const struct nlmsghdr *nlh = commp->nlh;
-	struct net *net = sock_net(in_skb->sk);
+	struct sk_buff *skb = commp->skb;
 	struct sk_buff *rep;
 	int err;
 
 	err = sock_diag_check_cookie(sk, req->id.idiag_cookie);
 	if (err)
-		goto out;
+		return err;
 
-	err = -ENOMEM;
 	rep = nlmsg_new(inet_assoc_attr_size(assoc), GFP_KERNEL);
 	if (!rep)
-		goto out;
+		return -ENOMEM;
 
 	lock_sock(sk);
-	if (sk != assoc->base.sk) {
-		release_sock(sk);
-		sk = assoc->base.sk;
-		lock_sock(sk);
-	}
-	err = inet_sctp_diag_fill(sk, assoc, rep, req,
-				  sk_user_ns(NETLINK_CB(in_skb).sk),
-				  NETLINK_CB(in_skb).portid,
-				  nlh->nlmsg_seq, 0, nlh,
-				  commp->net_admin);
-	release_sock(sk);
+	if (ep != assoc->ep) {
+		err = -EAGAIN;
+		goto out;
+	}
+
+	err = inet_sctp_diag_fill(sk, assoc, rep, req, sk_user_ns(NETLINK_CB(skb).sk),
+				  NETLINK_CB(skb).portid, commp->nlh->nlmsg_seq, 0,
+				  commp->nlh, commp->net_admin);
 	if (err < 0) {
 		WARN_ON(err == -EMSGSIZE);
-		kfree_skb(rep);
 		goto out;
 	}
+	release_sock(sk);
 
-	err = nlmsg_unicast(net->diag_nlsk, rep, NETLINK_CB(in_skb).portid);
+	return nlmsg_unicast(sock_net(skb->sk)->diag_nlsk, rep, NETLINK_CB(skb).portid);
 
 out:
+	release_sock(sk);
+	kfree_skb(rep);
 	return err;
 }
 
-static int sctp_sock_dump(struct sctp_transport *tsp, void *p)
+static int sctp_sock_dump(struct sctp_endpoint *ep, struct sctp_transport *tsp, void *p)
 {
-	struct sctp_endpoint *ep = tsp->asoc->ep;
 	struct sctp_comm_param *commp = p;
 	struct sock *sk = ep->base.sk;
 	struct sk_buff *skb = commp->skb;
@@ -302,6 +294,8 @@
 	int err = 0;
 
 	lock_sock(sk);
+	if (ep != tsp->asoc->ep)
+		goto release;
 	list_for_each_entry(assoc, &ep->asocs, asocs) {
 		if (cb->args[4] < cb->args[1])
 			goto next;
@@ -344,17 +338,14 @@
 	return err;
 }
 
-static int sctp_sock_filter(struct sctp_transport *tsp, void *p)
+static int sctp_sock_filter(struct sctp_endpoint *ep, struct sctp_transport *tsp, void *p)
 {
-	struct sctp_endpoint *ep = tsp->asoc->ep;
 	struct sctp_comm_param *commp = p;
 	struct sock *sk = ep->base.sk;
 	const struct inet_diag_req_v2 *r = commp->r;
-	struct sctp_association *assoc =
-		list_entry(ep->asocs.next, struct sctp_association, asocs);
 
 	/* find the ep only once through the transports by this condition */
-	if (tsp->asoc != assoc)
+	if (!list_is_first(&tsp->asoc->asocs, &ep->asocs))
 		return 0;
 
 	if (r->sdiag_family != AF_UNSPEC && sk->sk_family != r->sdiag_family)
@@ -429,15 +420,15 @@
 static int sctp_diag_dump_one(struct netlink_callback *cb,
 			      const struct inet_diag_req_v2 *req)
 {
-	struct sk_buff *in_skb = cb->skb;
-	struct net *net = sock_net(in_skb->sk);
+	struct sk_buff *skb = cb->skb;
+	struct net *net = sock_net(skb->sk);
 	const struct nlmsghdr *nlh = cb->nlh;
 	union sctp_addr laddr, paddr;
 	struct sctp_comm_param commp = {
-		.skb = in_skb,
+		.skb = skb,
 		.r = req,
 		.nlh = nlh,
-		.net_admin = netlink_net_capable(in_skb, CAP_NET_ADMIN),
+		.net_admin = netlink_net_capable(skb, CAP_NET_ADMIN),
 	};
 
 	if (req->sdiag_family == AF_INET) {
@@ -460,7 +451,7 @@
 		paddr.v6.sin6_family = AF_INET6;
 	}
 
-	return sctp_transport_lookup_process(sctp_tsp_dump_one,
+	return sctp_transport_lookup_process(sctp_sock_dump_one,
 					     net, &laddr, &paddr, &commp);
 }
 
@@ -505,8 +496,8 @@
 	if (!(idiag_states & ~(TCPF_LISTEN | TCPF_CLOSE)))
 		goto done;
 
-	sctp_for_each_transport(sctp_sock_filter, sctp_sock_dump,
-				net, &pos, &commp);
+	sctp_transport_traverse_process(sctp_sock_filter, sctp_sock_dump,
+					net, &pos, &commp);
 	cb->args[2] = pos;
 
 done:
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/endpointola.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/endpointola.c
@@ -184,6 +184,18 @@
 }
 
 /* Final destructor for endpoint.  */
+static void sctp_endpoint_destroy_rcu(struct rcu_head *head)
+{
+	struct sctp_endpoint *ep = container_of(head, struct sctp_endpoint, rcu);
+	struct sock *sk = ep->base.sk;
+
+	sctp_sk(sk)->ep = NULL;
+	sock_put(sk);
+
+	kfree(ep);
+	SCTP_DBG_OBJCNT_DEC(ep);
+}
+
 static void sctp_endpoint_destroy(struct sctp_endpoint *ep)
 {
 	struct sock *sk;
@@ -213,18 +225,13 @@
 	if (sctp_sk(sk)->bind_hash)
 		sctp_put_port(sk);
 
-	sctp_sk(sk)->ep = NULL;
-	/* Give up our hold on the sock */
-	sock_put(sk);
-
-	kfree(ep);
-	SCTP_DBG_OBJCNT_DEC(ep);
+	call_rcu(&ep->rcu, sctp_endpoint_destroy_rcu);
 }
 
 /* Hold a reference to an endpoint. */
-void sctp_endpoint_hold(struct sctp_endpoint *ep)
+int sctp_endpoint_hold(struct sctp_endpoint *ep)
 {
-	refcount_inc(&ep->base.refcnt);
+	return refcount_inc_not_zero(&ep->base.refcnt);
 }
 
 /* Release a reference to an endpoint and clean up if there are
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/input.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/input.c
@@ -92,6 +92,7 @@
 	struct sctp_chunk *chunk;
 	union sctp_addr src;
 	union sctp_addr dest;
+	int bound_dev_if;
 	int family;
 	struct sctp_af *af;
 	struct net *net = dev_net(skb->dev);
@@ -169,7 +170,8 @@
 	 * If a frame arrives on an interface and the receiving socket is
 	 * bound to another interface, via SO_BINDTODEVICE, treat it as OOTB
 	 */
-	if (sk->sk_bound_dev_if && (sk->sk_bound_dev_if != af->skb_iif(skb))) {
+	bound_dev_if = READ_ONCE(sk->sk_bound_dev_if);
+	if (bound_dev_if && (bound_dev_if != af->skb_iif(skb))) {
 		if (transport) {
 			sctp_transport_put(transport);
 			asoc = NULL;
@@ -746,23 +748,25 @@
 	struct sock *sk = ep->base.sk;
 	struct net *net = sock_net(sk);
 	struct sctp_hashbucket *head;
-	struct sctp_ep_common *epb;
+	int err = 0;
 
-	epb = &ep->base;
-	epb->hashent = sctp_ep_hashfn(net, epb->bind_addr.port);
-	head = &sctp_ep_hashtable[epb->hashent];
+	ep->hashent = sctp_ep_hashfn(net, ep->base.bind_addr.port);
+	head = &sctp_ep_hashtable[ep->hashent];
 
+	write_lock(&head->lock);
 	if (sk->sk_reuseport) {
 		bool any = sctp_is_ep_boundall(sk);
-		struct sctp_ep_common *epb2;
+		struct sctp_endpoint *ep2;
 		struct list_head *list;
-		int cnt = 0, err = 1;
+		int cnt = 0;
+
+		err = 1;
 
 		list_for_each(list, &ep->base.bind_addr.address_list)
 			cnt++;
 
-		sctp_for_each_hentry(epb2, &head->chain) {
-			struct sock *sk2 = epb2->sk;
+		sctp_for_each_hentry(ep2, &head->chain) {
+			struct sock *sk2 = ep2->base.sk;
 
 			if (!net_eq(sock_net(sk2), net) || sk2 == sk ||
 			    !uid_eq(sock_i_uid(sk2), sock_i_uid(sk)) ||
@@ -774,24 +778,24 @@
 			if (!err) {
 				err = reuseport_add_sock(sk, sk2, any);
 				if (err)
-					return err;
+					goto out;
 				break;
 			} else if (err < 0) {
-				return err;
+				goto out;
 			}
 		}
 
 		if (err) {
 			err = reuseport_alloc(sk, any);
 			if (err)
-				return err;
+				goto out;
 		}
 	}
 
-	write_lock(&head->lock);
-	hlist_add_head(&epb->node, &head->chain);
+	hlist_add_head(&ep->node, &head->chain);
+out:
 	write_unlock(&head->lock);
-	return 0;
+	return err;
 }
 
 /* Add an endpoint to the hash. Local BH-safe. */
@@ -811,19 +815,15 @@
 {
 	struct sock *sk = ep->base.sk;
 	struct sctp_hashbucket *head;
-	struct sctp_ep_common *epb;
-
-	epb = &ep->base;
 
-	epb->hashent = sctp_ep_hashfn(sock_net(sk), epb->bind_addr.port);
+	ep->hashent = sctp_ep_hashfn(sock_net(sk), ep->base.bind_addr.port);
 
-	head = &sctp_ep_hashtable[epb->hashent];
+	head = &sctp_ep_hashtable[ep->hashent];
 
+	write_lock(&head->lock);
 	if (rcu_access_pointer(sk->sk_reuseport_cb))
 		reuseport_detach_sock(sk);
-
-	write_lock(&head->lock);
-	hlist_del_init(&epb->node);
+	hlist_del_init(&ep->node);
 	write_unlock(&head->lock);
 }
 
@@ -856,7 +856,6 @@
 					const union sctp_addr *paddr)
 {
 	struct sctp_hashbucket *head;
-	struct sctp_ep_common *epb;
 	struct sctp_endpoint *ep;
 	struct sock *sk;
 	__be16 lport;
@@ -866,8 +865,7 @@
 	hash = sctp_ep_hashfn(net, ntohs(lport));
 	head = &sctp_ep_hashtable[hash];
 	read_lock(&head->lock);
-	sctp_for_each_hentry(epb, &head->chain) {
-		ep = sctp_ep(epb);
+	sctp_for_each_hentry(ep, &head->chain) {
 		if (sctp_endpoint_is_match(ep, net, laddr))
 			goto hit;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/output.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/output.c
@@ -581,13 +581,16 @@
 	chunk = list_entry(packet->chunk_list.next, struct sctp_chunk, list);
 	sk = chunk->skb->sk;
 
-	/* check gso */
 	if (packet->size > tp->pathmtu && !packet->ipfragok && !chunk->pmtu_probe) {
-		if (!sk_can_gso(sk)) {
-			pr_err_once("Trying to GSO but underlying device doesn't support it.");
-			goto out;
+		if (tp->pl.state == SCTP_PL_ERROR) { /* do IP fragmentation if in Error state */
+			packet->ipfragok = 1;
+		} else {
+			if (!sk_can_gso(sk)) { /* check gso */
+				pr_err_once("Trying to GSO but underlying device doesn't support it.");
+				goto out;
+			}
+			gso = 1;
 		}
-		gso = 1;
 	}
 
 	/* alloc head skb */
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/outqueue.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/outqueue.c
@@ -384,6 +384,7 @@
 {
 	struct sctp_outq *q = &asoc->outqueue;
 	struct sctp_chunk *chk, *temp;
+	struct sctp_stream_out *sout;
 
 	q->sched->unsched_all(&asoc->stream);
 
@@ -398,12 +399,14 @@
 		sctp_sched_dequeue_common(q, chk);
 		asoc->sent_cnt_removable--;
 		asoc->abandoned_unsent[SCTP_PR_INDEX(PRIO)]++;
-		if (chk->sinfo.sinfo_stream < asoc->stream.outcnt) {
-			struct sctp_stream_out *streamout =
-				SCTP_SO(&asoc->stream, chk->sinfo.sinfo_stream);
 
-			streamout->ext->abandoned_unsent[SCTP_PR_INDEX(PRIO)]++;
-		}
+		sout = SCTP_SO(&asoc->stream, chk->sinfo.sinfo_stream);
+		sout->ext->abandoned_unsent[SCTP_PR_INDEX(PRIO)]++;
+
+		/* clear out_curr if all frag chunks are pruned */
+		if (asoc->stream.out_curr == sout &&
+		    list_is_last(&chk->frag_list, &chk->msg->chunks))
+			asoc->stream.out_curr = NULL;
 
 		msg_len -= chk->skb->truesize + sizeof(struct sctp_chunk);
 		sctp_chunk_free(chk);
@@ -911,6 +914,7 @@
 				ctx->asoc->base.sk->sk_err = -error;
 				return;
 			}
+			ctx->asoc->stats.octrlchunks++;
 			break;
 
 		case SCTP_CID_ABORT:
@@ -935,7 +939,10 @@
 
 		case SCTP_CID_HEARTBEAT:
 			if (chunk->pmtu_probe) {
-				sctp_packet_singleton(ctx->transport, chunk, ctx->gfp);
+				error = sctp_packet_singleton(ctx->transport,
+							      chunk, ctx->gfp);
+				if (!error)
+					ctx->asoc->stats.octrlchunks++;
 				break;
 			}
 			fallthrough;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/proc.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/proc.c
@@ -161,7 +161,6 @@
 static int sctp_eps_seq_show(struct seq_file *seq, void *v)
 {
 	struct sctp_hashbucket *head;
-	struct sctp_ep_common *epb;
 	struct sctp_endpoint *ep;
 	struct sock *sk;
 	int    hash = *(loff_t *)v;
@@ -171,18 +170,17 @@
 
 	head = &sctp_ep_hashtable[hash];
 	read_lock_bh(&head->lock);
-	sctp_for_each_hentry(epb, &head->chain) {
-		ep = sctp_ep(epb);
-		sk = epb->sk;
+	sctp_for_each_hentry(ep, &head->chain) {
+		sk = ep->base.sk;
 		if (!net_eq(sock_net(sk), seq_file_net(seq)))
 			continue;
 		seq_printf(seq, "%8pK %8pK %-3d %-3d %-4d %-5d %5u %5lu ", ep, sk,
 			   sctp_sk(sk)->type, sk->sk_state, hash,
-			   epb->bind_addr.port,
+			   ep->base.bind_addr.port,
 			   from_kuid_munged(seq_user_ns(seq), sock_i_uid(sk)),
 			   sock_i_ino(sk));
 
-		sctp_seq_dump_local_addrs(seq, epb);
+		sctp_seq_dump_local_addrs(seq, &ep->base);
 		seq_printf(seq, "\n");
 	}
 	read_unlock_bh(&head->lock);
@@ -284,7 +282,7 @@
 		assoc->init_retries, assoc->shutdown_retries,
 		assoc->rtx_data_chunks,
 		refcount_read(&sk->sk_wmem_alloc),
-		sk->sk_wmem_queued,
+		READ_ONCE(sk->sk_wmem_queued),
 		sk->sk_sndbuf,
 		sk->sk_rcvbuf);
 	seq_printf(seq, "\n");
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/protocol.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/protocol.c
@@ -359,7 +359,7 @@
 	if (addr->v4.sin_addr.s_addr != htonl(INADDR_ANY) &&
 	   ret != RTN_LOCAL &&
 	   !sp->inet.freebind &&
-	   !net->ipv4.sysctl_ip_nonlocal_bind)
+	    !READ_ONCE(net->ipv4.sysctl_ip_nonlocal_bind))
 		return 0;
 
 	if (ipv6_only_sock(sctp_opt2sk(sp)))
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/sm_sideeffect.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/sm_sideeffect.c
@@ -458,6 +458,10 @@
 		goto out_unlock;
 	}
 
+	/* This happens when the response arrives after the timer is triggered. */
+	if (!asoc->strreset_chunk)
+		goto out_unlock;
+
 	error = sctp_do_sm(net, SCTP_EVENT_T_TIMEOUT,
 			   SCTP_ST_TIMEOUT(SCTP_EVENT_TIMEOUT_RECONF),
 			   asoc->state, asoc->ep, asoc,
@@ -1247,7 +1251,10 @@
 	default:
 		pr_err("impossible disposition %d in state %d, event_type %d, event_id %d\n",
 		       status, state, event_type, subtype.chunk);
-		BUG();
+		error = status;
+		if (error >= 0)
+			error = -EINVAL;
+		WARN_ON_ONCE(1);
 		break;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/sm_statefuns.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/sm_statefuns.c
@@ -3736,7 +3736,7 @@
 		}
 
 		ch = (struct sctp_chunkhdr *)ch_end;
-	} while (ch_end < skb_tail_pointer(skb));
+	} while (ch_end + sizeof(*ch) < skb_tail_pointer(skb));
 
 	if (ootb_shut_ack)
 		return sctp_sf_shut_8_4_5(net, ep, asoc, type, arg, commands);
@@ -4478,7 +4478,7 @@
 				    SCTP_AUTH_NEW_KEY, GFP_ATOMIC);
 
 		if (!ev)
-			return -ENOMEM;
+			return SCTP_DISPOSITION_NOMEM;
 
 		sctp_add_cmd_sf(commands, SCTP_CMD_EVENT_ULP,
 				SCTP_ULPEVENT(ev));
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/socket.c
@@ -68,7 +68,7 @@
 #include <net/sctp/stream_sched.h>
 
 /* Forward declarations for internal helper functions. */
-static bool sctp_writeable(struct sock *sk);
+static bool sctp_writeable(const struct sock *sk);
 static void sctp_wfree(struct sk_buff *skb);
 static int sctp_wait_for_sndbuf(struct sctp_association *asoc, long *timeo_p,
 				size_t msg_len);
@@ -97,7 +97,7 @@
 
 static void sctp_enter_memory_pressure(struct sock *sk)
 {
-	sctp_memory_pressure = 1;
+	WRITE_ONCE(sctp_memory_pressure, 1);
 }
 
 
@@ -138,7 +138,7 @@
 
 	refcount_add(sizeof(struct sctp_chunk), &sk->sk_wmem_alloc);
 	asoc->sndbuf_used += chunk->skb->truesize + sizeof(struct sctp_chunk);
-	sk->sk_wmem_queued += chunk->skb->truesize + sizeof(struct sctp_chunk);
+	sk_wmem_queued_add(sk, chunk->skb->truesize + sizeof(struct sctp_chunk));
 	sk_mem_charge(sk, chunk->skb->truesize);
 }
 
@@ -362,9 +362,9 @@
 	struct net *net = sock_net(&sp->inet.sk);
 
 	if (net->sctp.default_auto_asconf) {
-		spin_lock(&net->sctp.addr_wq_lock);
+		spin_lock_bh(&net->sctp.addr_wq_lock);
 		list_add_tail(&sp->auto_asconf_list, &net->sctp.auto_asconf_splist);
-		spin_unlock(&net->sctp.addr_wq_lock);
+		spin_unlock_bh(&net->sctp.addr_wq_lock);
 		sp->do_auto_asconf = 1;
 	}
 }
@@ -1831,6 +1831,10 @@
 		err = sctp_wait_for_sndbuf(asoc, &timeo, msg_len);
 		if (err)
 			goto err;
+		if (unlikely(sinfo->sinfo_stream >= asoc->stream.outcnt)) {
+			err = -EINVAL;
+			goto err;
+		}
 	}
 
 	if (sctp_state(asoc, CLOSED)) {
@@ -2448,6 +2452,7 @@
 			if (trans) {
 				trans->hbinterval =
 				    msecs_to_jiffies(params->spp_hbinterval);
+				sctp_transport_reset_hb_timer(trans);
 			} else if (asoc) {
 				asoc->hbinterval =
 				    msecs_to_jiffies(params->spp_hbinterval);
@@ -5068,12 +5073,9 @@
 
 	SCTP_DBG_OBJCNT_INC(sock);
 
-	local_bh_disable();
 	sk_sockets_allocated_inc(sk);
 	sock_prot_inuse_add(net, sk->sk_prot, 1);
 
-	local_bh_enable();
-
 	return 0;
 }
 
@@ -5099,20 +5101,22 @@
 		list_del(&sp->auto_asconf_list);
 	}
 	sctp_endpoint_free(sp->ep);
-	local_bh_disable();
 	sk_sockets_allocated_dec(sk);
 	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, -1);
-	local_bh_enable();
 }
 
 /* Triggered when there are no references on the socket anymore */
-static void sctp_destruct_sock(struct sock *sk)
+static void sctp_destruct_common(struct sock *sk)
 {
 	struct sctp_sock *sp = sctp_sk(sk);
 
 	/* Free up the HMAC transform. */
 	crypto_free_shash(sp->hmac);
+}
 
+static void sctp_destruct_sock(struct sock *sk)
+{
+	sctp_destruct_common(sk);
 	inet_sock_destruct(sk);
 }
 
@@ -5299,14 +5303,14 @@
 			   void *p) {
 	int err = 0;
 	int hash = 0;
-	struct sctp_ep_common *epb;
+	struct sctp_endpoint *ep;
 	struct sctp_hashbucket *head;
 
 	for (head = sctp_ep_hashtable; hash < sctp_ep_hashsize;
 	     hash++, head++) {
 		read_lock_bh(&head->lock);
-		sctp_for_each_hentry(epb, &head->chain) {
-			err = cb(sctp_ep(epb), p);
+		sctp_for_each_hentry(ep, &head->chain) {
+			err = cb(ep, p);
 			if (err)
 				break;
 		}
@@ -5317,32 +5321,41 @@
 }
 EXPORT_SYMBOL_GPL(sctp_for_each_endpoint);
 
-int sctp_transport_lookup_process(int (*cb)(struct sctp_transport *, void *),
-				  struct net *net,
+int sctp_transport_lookup_process(sctp_callback_t cb, struct net *net,
 				  const union sctp_addr *laddr,
 				  const union sctp_addr *paddr, void *p)
 {
 	struct sctp_transport *transport;
-	int err;
+	struct sctp_endpoint *ep;
+	int err = -ENOENT;
 
 	rcu_read_lock();
 	transport = sctp_addrs_lookup_transport(net, laddr, paddr);
+	if (!transport) {
+		rcu_read_unlock();
+		return err;
+	}
+	ep = transport->asoc->ep;
+	if (!sctp_endpoint_hold(ep)) { /* asoc can be peeled off */
+		sctp_transport_put(transport);
+		rcu_read_unlock();
+		return err;
+	}
 	rcu_read_unlock();
-	if (!transport)
-		return -ENOENT;
 
-	err = cb(transport, p);
+	err = cb(ep, transport, p);
+	sctp_endpoint_put(ep);
 	sctp_transport_put(transport);
-
 	return err;
 }
 EXPORT_SYMBOL_GPL(sctp_transport_lookup_process);
 
-int sctp_for_each_transport(int (*cb)(struct sctp_transport *, void *),
-			    int (*cb_done)(struct sctp_transport *, void *),
-			    struct net *net, int *pos, void *p) {
+int sctp_transport_traverse_process(sctp_callback_t cb, sctp_callback_t cb_done,
+				    struct net *net, int *pos, void *p)
+{
 	struct rhashtable_iter hti;
 	struct sctp_transport *tsp;
+	struct sctp_endpoint *ep;
 	int ret;
 
 again:
@@ -5351,26 +5364,32 @@
 
 	tsp = sctp_transport_get_idx(net, &hti, *pos + 1);
 	for (; !IS_ERR_OR_NULL(tsp); tsp = sctp_transport_get_next(net, &hti)) {
-		ret = cb(tsp, p);
-		if (ret)
-			break;
+		ep = tsp->asoc->ep;
+		if (sctp_endpoint_hold(ep)) { /* asoc can be peeled off */
+			ret = cb(ep, tsp, p);
+			if (ret)
+				break;
+			sctp_endpoint_put(ep);
+		}
 		(*pos)++;
 		sctp_transport_put(tsp);
 	}
 	sctp_transport_walk_stop(&hti);
 
 	if (ret) {
-		if (cb_done && !cb_done(tsp, p)) {
+		if (cb_done && !cb_done(ep, tsp, p)) {
 			(*pos)++;
+			sctp_endpoint_put(ep);
 			sctp_transport_put(tsp);
 			goto again;
 		}
+		sctp_endpoint_put(ep);
 		sctp_transport_put(tsp);
 	}
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(sctp_for_each_transport);
+EXPORT_SYMBOL_GPL(sctp_transport_traverse_process);
 
 /* 7.2.1 Association Status (SCTP_STATUS)
 
@@ -5626,7 +5645,7 @@
 	 * Set the daddr and initialize id to something more random and also
 	 * copy over any ip options.
 	 */
-	sp->pf->to_sk_daddr(&asoc->peer.primary_addr, sk);
+	sp->pf->to_sk_daddr(&asoc->peer.primary_addr, sock->sk);
 	sp->pf->copy_ip_options(sk, sock->sk);
 
 	/* Populate the fields of the newsk from the oldsk and migrate the
@@ -7093,6 +7112,7 @@
 	struct sctp_sock *sp = sctp_sk(sk);
 	struct sctp_association *asoc;
 	struct sctp_assoc_ids *ids;
+	size_t ids_size;
 	u32 num = 0;
 
 	if (sctp_style(sk, TCP))
@@ -7105,11 +7125,11 @@
 		num++;
 	}
 
-	if (len < sizeof(struct sctp_assoc_ids) + sizeof(sctp_assoc_t) * num)
+	ids_size = struct_size(ids, gaids_assoc_id, num);
+	if (len < ids_size)
 		return -EINVAL;
 
-	len = sizeof(struct sctp_assoc_ids) + sizeof(sctp_assoc_t) * num;
-
+	len = ids_size;
 	ids = kmalloc(len, GFP_USER | __GFP_NOWARN);
 	if (unlikely(!ids))
 		return -ENOMEM;
@@ -8264,6 +8284,22 @@
 	return retval;
 }
 
+static bool sctp_bpf_bypass_getsockopt(int level, int optname)
+{
+	if (level == SOL_SCTP) {
+		switch (optname) {
+		case SCTP_SOCKOPT_PEELOFF:
+		case SCTP_SOCKOPT_PEELOFF_FLAGS:
+		case SCTP_SOCKOPT_CONNECTX3:
+			return true;
+		default:
+			return false;
+		}
+	}
+
+	return false;
+}
+
 static int sctp_hash(struct sock *sk)
 {
 	/* STUB */
@@ -8480,6 +8516,7 @@
 	struct sctp_endpoint *ep = sp->ep;
 	struct crypto_shash *tfm = NULL;
 	char alg[32];
+	int err;
 
 	/* Allocate HMAC for generating cookie. */
 	if (!sp->hmac && sp->sctp_hmac_alg) {
@@ -8506,17 +8543,26 @@
 	 */
 	inet_sk_set_state(sk, SCTP_SS_LISTENING);
 	if (!ep->base.bind_addr.port) {
-		if (sctp_autobind(sk))
-			return -EAGAIN;
+		if (sctp_autobind(sk)) {
+			err = -EAGAIN;
+			goto err;
+		}
 	} else {
 		if (sctp_get_port(sk, inet_sk(sk)->inet_num)) {
-			inet_sk_set_state(sk, SCTP_SS_CLOSED);
-			return -EADDRINUSE;
+			err = -EADDRINUSE;
+			goto err;
 		}
 	}
 
 	WRITE_ONCE(sk->sk_max_ack_backlog, backlog);
-	return sctp_hash_endpoint(ep);
+	err = sctp_hash_endpoint(ep);
+	if (err)
+		goto err;
+
+	return 0;
+err:
+	inet_sk_set_state(sk, SCTP_SS_CLOSED);
+	return err;
 }
 
 /*
@@ -9109,7 +9155,7 @@
 	struct sock *sk = asoc->base.sk;
 
 	sk_mem_uncharge(sk, skb->truesize);
-	sk->sk_wmem_queued -= skb->truesize + sizeof(struct sctp_chunk);
+	sk_wmem_queued_add(sk, -(skb->truesize + sizeof(struct sctp_chunk)));
 	asoc->sndbuf_used -= skb->truesize + sizeof(struct sctp_chunk);
 	WARN_ON(refcount_sub_and_test(sizeof(struct sctp_chunk),
 				      &sk->sk_wmem_alloc));
@@ -9264,9 +9310,9 @@
  * UDP-style sockets or TCP-style sockets, this code should work.
  *  - Daisy
  */
-static bool sctp_writeable(struct sock *sk)
+static bool sctp_writeable(const struct sock *sk)
 {
-	return sk->sk_sndbuf > sk->sk_wmem_queued;
+	return READ_ONCE(sk->sk_sndbuf) > READ_ONCE(sk->sk_wmem_queued);
 }
 
 /* Wait for an association to go into ESTABLISHED state. If timeout is 0,
@@ -9424,7 +9470,7 @@
 	sctp_sk(newsk)->reuse = sp->reuse;
 
 	newsk->sk_shutdown = sk->sk_shutdown;
-	newsk->sk_destruct = sctp_destruct_sock;
+	newsk->sk_destruct = sk->sk_destruct;
 	newsk->sk_family = sk->sk_family;
 	newsk->sk_protocol = IPPROTO_SCTP;
 	newsk->sk_backlog_rcv = sk->sk_prot->backlog_rcv;
@@ -9632,6 +9678,7 @@
 	.shutdown    =	sctp_shutdown,
 	.setsockopt  =	sctp_setsockopt,
 	.getsockopt  =	sctp_getsockopt,
+	.bpf_bypass_getsockopt	= sctp_bpf_bypass_getsockopt,
 	.sendmsg     =	sctp_sendmsg,
 	.recvmsg     =	sctp_recvmsg,
 	.bind        =	sctp_bind,
@@ -9656,11 +9703,20 @@
 
 #if IS_ENABLED(CONFIG_IPV6)
 
-#include <net/transp_v6.h>
-static void sctp_v6_destroy_sock(struct sock *sk)
+static void sctp_v6_destruct_sock(struct sock *sk)
 {
-	sctp_destroy_sock(sk);
-	inet6_destroy_sock(sk);
+	sctp_destruct_common(sk);
+	inet6_sock_destruct(sk);
+}
+
+static int sctp_v6_init_sock(struct sock *sk)
+{
+	int ret = sctp_init_sock(sk);
+
+	if (!ret)
+		sk->sk_destruct = sctp_v6_destruct_sock;
+
+	return ret;
 }
 
 struct proto sctpv6_prot = {
@@ -9670,11 +9726,12 @@
 	.disconnect	= sctp_disconnect,
 	.accept		= sctp_accept,
 	.ioctl		= sctp_ioctl,
-	.init		= sctp_init_sock,
-	.destroy	= sctp_v6_destroy_sock,
+	.init		= sctp_v6_init_sock,
+	.destroy	= sctp_destroy_sock,
 	.shutdown	= sctp_shutdown,
 	.setsockopt	= sctp_setsockopt,
 	.getsockopt	= sctp_getsockopt,
+	.bpf_bypass_getsockopt	= sctp_bpf_bypass_getsockopt,
 	.sendmsg	= sctp_sendmsg,
 	.recvmsg	= sctp_recvmsg,
 	.bind		= sctp_bind,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/stream.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/stream.c
@@ -52,6 +52,19 @@
 	}
 }
 
+static void sctp_stream_free_ext(struct sctp_stream *stream, __u16 sid)
+{
+	struct sctp_sched_ops *sched;
+
+	if (!SCTP_SO(stream, sid)->ext)
+		return;
+
+	sched = sctp_sched_ops_from_stream(stream);
+	sched->free_sid(stream, sid);
+	kfree(SCTP_SO(stream, sid)->ext);
+	SCTP_SO(stream, sid)->ext = NULL;
+}
+
 /* Migrates chunks from stream queues to new stream queues if needed,
  * but not across associations. Also, removes those chunks to streams
  * higher than the new max.
@@ -70,16 +83,14 @@
 		 * sctp_stream_update will swap ->out pointers.
 		 */
 		for (i = 0; i < outcnt; i++) {
-			kfree(SCTP_SO(new, i)->ext);
+			sctp_stream_free_ext(new, i);
 			SCTP_SO(new, i)->ext = SCTP_SO(stream, i)->ext;
 			SCTP_SO(stream, i)->ext = NULL;
 		}
 	}
 
-	for (i = outcnt; i < stream->outcnt; i++) {
-		kfree(SCTP_SO(stream, i)->ext);
-		SCTP_SO(stream, i)->ext = NULL;
-	}
+	for (i = outcnt; i < stream->outcnt; i++)
+		sctp_stream_free_ext(stream, i);
 }
 
 static int sctp_stream_alloc_out(struct sctp_stream *stream, __u16 outcnt,
@@ -137,7 +148,7 @@
 
 	ret = sctp_stream_alloc_out(stream, outcnt, gfp);
 	if (ret)
-		goto out_err;
+		return ret;
 
 	for (i = 0; i < stream->outcnt; i++)
 		SCTP_SO(stream, i)->state = SCTP_STREAM_OPEN;
@@ -145,22 +156,9 @@
 handle_in:
 	sctp_stream_interleave_init(stream);
 	if (!incnt)
-		goto out;
+		return 0;
 
-	ret = sctp_stream_alloc_in(stream, incnt, gfp);
-	if (ret)
-		goto in_err;
-
-	goto out;
-
-in_err:
-	sched->free(stream);
-	genradix_free(&stream->in);
-out_err:
-	genradix_free(&stream->out);
-	stream->outcnt = 0;
-out:
-	return ret;
+	return sctp_stream_alloc_in(stream, incnt, gfp);
 }
 
 int sctp_stream_init_ext(struct sctp_stream *stream, __u16 sid)
@@ -187,9 +185,9 @@
 	struct sctp_sched_ops *sched = sctp_sched_ops_from_stream(stream);
 	int i;
 
-	sched->free(stream);
+	sched->unsched_all(stream);
 	for (i = 0; i < stream->outcnt; i++)
-		kfree(SCTP_SO(stream, i)->ext);
+		sctp_stream_free_ext(stream, i);
 	genradix_free(&stream->out);
 	genradix_free(&stream->in);
 }
@@ -737,7 +735,7 @@
 	 *     value SHOULD be the smallest TSN not acknowledged by the
 	 *     receiver of the request plus 2^31.
 	 */
-	init_tsn = sctp_tsnmap_get_ctsn(&asoc->peer.tsn_map) + (1 << 31);
+	init_tsn = sctp_tsnmap_get_ctsn(&asoc->peer.tsn_map) + (1U << 31);
 	sctp_tsnmap_init(&asoc->peer.tsn_map, SCTP_TSN_MAP_INITIAL,
 			 init_tsn, GFP_ATOMIC);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/stream_interleave.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/stream_interleave.c
@@ -1162,7 +1162,8 @@
 
 #define _sctp_walk_ifwdtsn(pos, chunk, end) \
 	for (pos = chunk->subh.ifwdtsn_hdr->skip; \
-	     (void *)pos < (void *)chunk->subh.ifwdtsn_hdr->skip + (end); pos++)
+	     (void *)pos <= (void *)chunk->subh.ifwdtsn_hdr->skip + (end) - \
+			    sizeof(struct sctp_ifwdtsn_skip); pos++)
 
 #define sctp_walk_ifwdtsn(pos, ch) \
 	_sctp_walk_ifwdtsn((pos), (ch), ntohs((ch)->chunk_hdr->length) - \
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/stream_sched.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/stream_sched.c
@@ -46,6 +46,10 @@
 	return 0;
 }
 
+static void sctp_sched_fcfs_free_sid(struct sctp_stream *stream, __u16 sid)
+{
+}
+
 static void sctp_sched_fcfs_free(struct sctp_stream *stream)
 {
 }
@@ -96,6 +100,7 @@
 	.get = sctp_sched_fcfs_get,
 	.init = sctp_sched_fcfs_init,
 	.init_sid = sctp_sched_fcfs_init_sid,
+	.free_sid = sctp_sched_fcfs_free_sid,
 	.free = sctp_sched_fcfs_free,
 	.enqueue = sctp_sched_fcfs_enqueue,
 	.dequeue = sctp_sched_fcfs_dequeue,
@@ -163,7 +168,7 @@
 		if (!SCTP_SO(&asoc->stream, i)->ext)
 			continue;
 
-		ret = n->init_sid(&asoc->stream, i, GFP_KERNEL);
+		ret = n->init_sid(&asoc->stream, i, GFP_ATOMIC);
 		if (ret)
 			goto err;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/stream_sched_prio.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/stream_sched_prio.c
@@ -25,6 +25,18 @@
 
 static void sctp_sched_prio_unsched_all(struct sctp_stream *stream);
 
+static struct sctp_stream_priorities *sctp_sched_prio_head_get(struct sctp_stream_priorities *p)
+{
+	p->users++;
+	return p;
+}
+
+static void sctp_sched_prio_head_put(struct sctp_stream_priorities *p)
+{
+	if (p && --p->users == 0)
+		kfree(p);
+}
+
 static struct sctp_stream_priorities *sctp_sched_prio_new_head(
 			struct sctp_stream *stream, int prio, gfp_t gfp)
 {
@@ -38,6 +50,7 @@
 	INIT_LIST_HEAD(&p->active);
 	p->next = NULL;
 	p->prio = prio;
+	p->users = 1;
 
 	return p;
 }
@@ -53,7 +66,7 @@
 	 */
 	list_for_each_entry(p, &stream->prio_list, prio_sched) {
 		if (p->prio == prio)
-			return p;
+			return sctp_sched_prio_head_get(p);
 		if (p->prio > prio)
 			break;
 	}
@@ -70,7 +83,7 @@
 			 */
 			break;
 		if (p->prio == prio)
-			return p;
+			return sctp_sched_prio_head_get(p);
 	}
 
 	/* If not even there, allocate a new one. */
@@ -154,32 +167,21 @@
 	struct sctp_stream_out_ext *soute = sout->ext;
 	struct sctp_stream_priorities *prio_head, *old;
 	bool reschedule = false;
-	int i;
+
+	old = soute->prio_head;
+	if (old && old->prio == prio)
+		return 0;
 
 	prio_head = sctp_sched_prio_get_head(stream, prio, gfp);
 	if (!prio_head)
 		return -ENOMEM;
 
 	reschedule = sctp_sched_prio_unsched(soute);
-	old = soute->prio_head;
 	soute->prio_head = prio_head;
 	if (reschedule)
 		sctp_sched_prio_sched(stream, soute);
 
-	if (!old)
-		/* Happens when we set the priority for the first time */
-		return 0;
-
-	for (i = 0; i < stream->outcnt; i++) {
-		soute = SCTP_SO(stream, i)->ext;
-		if (soute && soute->prio_head == old)
-			/* It's still in use, nothing else to do here. */
-			return 0;
-	}
-
-	/* No hits, we are good to free it. */
-	kfree(old);
-
+	sctp_sched_prio_head_put(old);
 	return 0;
 }
 
@@ -204,6 +206,12 @@
 	return sctp_sched_prio_set(stream, sid, 0, gfp);
 }
 
+static void sctp_sched_prio_free_sid(struct sctp_stream *stream, __u16 sid)
+{
+	sctp_sched_prio_head_put(SCTP_SO(stream, sid)->ext->prio_head);
+	SCTP_SO(stream, sid)->ext->prio_head = NULL;
+}
+
 static void sctp_sched_prio_free(struct sctp_stream *stream)
 {
 	struct sctp_stream_priorities *prio, *n;
@@ -323,6 +331,7 @@
 	.get = sctp_sched_prio_get,
 	.init = sctp_sched_prio_init,
 	.init_sid = sctp_sched_prio_init_sid,
+	.free_sid = sctp_sched_prio_free_sid,
 	.free = sctp_sched_prio_free,
 	.enqueue = sctp_sched_prio_enqueue,
 	.dequeue = sctp_sched_prio_dequeue,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/stream_sched_rr.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/stream_sched_rr.c
@@ -90,6 +90,10 @@
 	return 0;
 }
 
+static void sctp_sched_rr_free_sid(struct sctp_stream *stream, __u16 sid)
+{
+}
+
 static void sctp_sched_rr_free(struct sctp_stream *stream)
 {
 	sctp_sched_rr_unsched_all(stream);
@@ -177,6 +181,7 @@
 	.get = sctp_sched_rr_get,
 	.init = sctp_sched_rr_init,
 	.init_sid = sctp_sched_rr_init_sid,
+	.free_sid = sctp_sched_rr_free_sid,
 	.free = sctp_sched_rr_free,
 	.enqueue = sctp_sched_rr_enqueue,
 	.dequeue = sctp_sched_rr_dequeue,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/sysctl.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/sysctl.c
@@ -84,17 +84,18 @@
 	{ /* sentinel */ }
 };
 
+/* The following index defines are used in sctp_sysctl_net_register().
+ * If you add new items to the sctp_net_table, please ensure that
+ * the index values of these defines hold the same meaning indicated by
+ * their macro names when they appear in sctp_net_table.
+ */
+#define SCTP_RTO_MIN_IDX       0
+#define SCTP_RTO_MAX_IDX       1
+#define SCTP_PF_RETRANS_IDX    2
+#define SCTP_PS_RETRANS_IDX    3
+
 static struct ctl_table sctp_net_table[] = {
-	{
-		.procname	= "rto_initial",
-		.data		= &init_net.sctp.rto_initial,
-		.maxlen		= sizeof(unsigned int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1         = SYSCTL_ONE,
-		.extra2         = &timer_max
-	},
-	{
+	[SCTP_RTO_MIN_IDX] = {
 		.procname	= "rto_min",
 		.data		= &init_net.sctp.rto_min,
 		.maxlen		= sizeof(unsigned int),
@@ -103,7 +104,7 @@
 		.extra1         = SYSCTL_ONE,
 		.extra2         = &init_net.sctp.rto_max
 	},
-	{
+	[SCTP_RTO_MAX_IDX] =  {
 		.procname	= "rto_max",
 		.data		= &init_net.sctp.rto_max,
 		.maxlen		= sizeof(unsigned int),
@@ -112,6 +113,33 @@
 		.extra1         = &init_net.sctp.rto_min,
 		.extra2         = &timer_max
 	},
+	[SCTP_PF_RETRANS_IDX] = {
+		.procname	= "pf_retrans",
+		.data		= &init_net.sctp.pf_retrans,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= &init_net.sctp.ps_retrans,
+	},
+	[SCTP_PS_RETRANS_IDX] = {
+		.procname	= "ps_retrans",
+		.data		= &init_net.sctp.ps_retrans,
+		.maxlen		= sizeof(int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1		= &init_net.sctp.pf_retrans,
+		.extra2		= &ps_retrans_max,
+	},
+	{
+		.procname	= "rto_initial",
+		.data		= &init_net.sctp.rto_initial,
+		.maxlen		= sizeof(unsigned int),
+		.mode		= 0644,
+		.proc_handler	= proc_dointvec_minmax,
+		.extra1         = SYSCTL_ONE,
+		.extra2         = &timer_max
+	},
 	{
 		.procname	= "rto_alpha_exp_divisor",
 		.data		= &init_net.sctp.rto_alpha,
@@ -208,24 +236,6 @@
 		.extra2		= SYSCTL_INT_MAX,
 	},
 	{
-		.procname	= "pf_retrans",
-		.data		= &init_net.sctp.pf_retrans,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= SYSCTL_ZERO,
-		.extra2		= &init_net.sctp.ps_retrans,
-	},
-	{
-		.procname	= "ps_retrans",
-		.data		= &init_net.sctp.ps_retrans,
-		.maxlen		= sizeof(int),
-		.mode		= 0644,
-		.proc_handler	= proc_dointvec_minmax,
-		.extra1		= &init_net.sctp.pf_retrans,
-		.extra2		= &ps_retrans_max,
-	},
-	{
 		.procname	= "sndbuf_policy",
 		.data		= &init_net.sctp.sndbuf_policy,
 		.maxlen		= sizeof(int),
@@ -370,7 +380,8 @@
 static int proc_sctp_do_hmac_alg(struct ctl_table *ctl, int write,
 				 void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct net *net = current->nsproxy->net_ns;
+	struct net *net = container_of(ctl->data, struct net,
+				       sctp.sctp_hmac_alg);
 	struct ctl_table tbl;
 	bool changed = false;
 	char *none = "none";
@@ -415,7 +426,7 @@
 static int proc_sctp_do_rto_min(struct ctl_table *ctl, int write,
 				void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct net *net = current->nsproxy->net_ns;
+	struct net *net = container_of(ctl->data, struct net, sctp.rto_min);
 	unsigned int min = *(unsigned int *) ctl->extra1;
 	unsigned int max = *(unsigned int *) ctl->extra2;
 	struct ctl_table tbl;
@@ -443,7 +454,7 @@
 static int proc_sctp_do_rto_max(struct ctl_table *ctl, int write,
 				void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct net *net = current->nsproxy->net_ns;
+	struct net *net = container_of(ctl->data, struct net, sctp.rto_max);
 	unsigned int min = *(unsigned int *) ctl->extra1;
 	unsigned int max = *(unsigned int *) ctl->extra2;
 	struct ctl_table tbl;
@@ -481,7 +492,7 @@
 static int proc_sctp_do_auth(struct ctl_table *ctl, int write,
 			     void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct net *net = current->nsproxy->net_ns;
+	struct net *net = container_of(ctl->data, struct net, sctp.auth_enable);
 	struct ctl_table tbl;
 	int new_value, ret;
 
@@ -510,7 +521,7 @@
 static int proc_sctp_do_udp_port(struct ctl_table *ctl, int write,
 				 void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct net *net = current->nsproxy->net_ns;
+	struct net *net = container_of(ctl->data, struct net, sctp.udp_port);
 	unsigned int min = *(unsigned int *)ctl->extra1;
 	unsigned int max = *(unsigned int *)ctl->extra2;
 	struct ctl_table tbl;
@@ -551,7 +562,8 @@
 static int proc_sctp_do_probe_interval(struct ctl_table *ctl, int write,
 				       void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct net *net = current->nsproxy->net_ns;
+	struct net *net = container_of(ctl->data, struct net,
+				       sctp.probe_interval);
 	struct ctl_table tbl;
 	int ret, new_value;
 
@@ -586,6 +598,11 @@
 	for (i = 0; table[i].data; i++)
 		table[i].data += (char *)(&net->sctp) - (char *)&init_net.sctp;
 
+	table[SCTP_RTO_MIN_IDX].extra2 = &net->sctp.rto_max;
+	table[SCTP_RTO_MAX_IDX].extra1 = &net->sctp.rto_min;
+	table[SCTP_PF_RETRANS_IDX].extra2 = &net->sctp.ps_retrans;
+	table[SCTP_PS_RETRANS_IDX].extra1 = &net->sctp.pf_retrans;
+
 	net->sctp.sysctl_header = register_net_sysctl(net, "net/sctp", table);
 	if (net->sctp.sysctl_header == NULL) {
 		kfree(table);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sctp/transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/sctp/transport.c
@@ -269,7 +269,7 @@
 		if (t->pl.probe_size == SCTP_BASE_PLPMTU) { /* BASE_PLPMTU Confirmation Failed */
 			t->pl.state = SCTP_PL_ERROR; /* Base -> Error */
 
-			t->pl.pmtu = SCTP_MIN_PLPMTU;
+			t->pl.pmtu = SCTP_BASE_PLPMTU;
 			t->pathmtu = t->pl.pmtu + sctp_transport_pl_hlen(t);
 			sctp_assoc_sync_pmtu(t->asoc);
 		}
@@ -331,9 +331,12 @@
 		t->pl.probe_size += SCTP_PL_BIG_STEP;
 	} else if (t->pl.state == SCTP_PL_SEARCH) {
 		if (!t->pl.probe_high) {
-			t->pl.probe_size = min(t->pl.probe_size + SCTP_PL_BIG_STEP,
-					       SCTP_MAX_PLPMTU);
-			return false;
+			if (t->pl.probe_size < SCTP_MAX_PLPMTU) {
+				t->pl.probe_size = min(t->pl.probe_size + SCTP_PL_BIG_STEP,
+						       SCTP_MAX_PLPMTU);
+				return false;
+			}
+			t->pl.probe_high = SCTP_MAX_PLPMTU;
 		}
 		t->pl.probe_size += SCTP_PL_MIN_STEP;
 		if (t->pl.probe_size >= t->pl.probe_high) {
@@ -348,7 +351,7 @@
 	} else if (t->pl.state == SCTP_PL_COMPLETE && t->pl.raise_count == 30) {
 		/* Raise probe_size again after 30 * interval in Search Complete */
 		t->pl.state = SCTP_PL_SEARCH; /* Search Complete -> Search */
-		t->pl.probe_size += SCTP_PL_MIN_STEP;
+		t->pl.probe_size = min(t->pl.probe_size + SCTP_PL_MIN_STEP, SCTP_MAX_PLPMTU);
 	}
 
 	return t->pl.state == SCTP_PL_COMPLETE;
@@ -366,8 +369,9 @@
 		if (pmtu >= SCTP_MIN_PLPMTU && pmtu < SCTP_BASE_PLPMTU) {
 			t->pl.state = SCTP_PL_ERROR; /* Base -> Error */
 
-			t->pl.pmtu = SCTP_MIN_PLPMTU;
+			t->pl.pmtu = SCTP_BASE_PLPMTU;
 			t->pathmtu = t->pl.pmtu + sctp_transport_pl_hlen(t);
+			return true;
 		}
 	} else if (t->pl.state == SCTP_PL_SEARCH) {
 		if (pmtu >= SCTP_BASE_PLPMTU && pmtu < t->pl.pmtu) {
@@ -378,11 +382,10 @@
 			t->pl.probe_high = 0;
 			t->pl.pmtu = SCTP_BASE_PLPMTU;
 			t->pathmtu = t->pl.pmtu + sctp_transport_pl_hlen(t);
+			return true;
 		} else if (pmtu > t->pl.pmtu && pmtu < t->pl.probe_size) {
 			t->pl.probe_size = pmtu;
 			t->pl.probe_count = 0;
-
-			return false;
 		}
 	} else if (t->pl.state == SCTP_PL_COMPLETE) {
 		if (pmtu >= SCTP_BASE_PLPMTU && pmtu < t->pl.pmtu) {
@@ -393,10 +396,11 @@
 			t->pl.probe_high = 0;
 			t->pl.pmtu = SCTP_BASE_PLPMTU;
 			t->pathmtu = t->pl.pmtu + sctp_transport_pl_hlen(t);
+			return true;
 		}
 	}
 
-	return true;
+	return false;
 }
 
 bool sctp_transport_update_pmtu(struct sctp_transport *t, u32 pmtu)
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/af_smc.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/af_smc.c
@@ -71,6 +71,46 @@
 	smc->clcsock->sk->sk_prot->keepalive(smc->clcsock->sk, val);
 }
 
+static struct sock *smc_tcp_syn_recv_sock(const struct sock *sk,
+					  struct sk_buff *skb,
+					  struct request_sock *req,
+					  struct dst_entry *dst,
+					  struct request_sock *req_unhash,
+					  bool *own_req)
+{
+	struct smc_sock *smc;
+	struct sock *child;
+
+	smc = smc_clcsock_user_data(sk);
+
+	if (READ_ONCE(sk->sk_ack_backlog) + atomic_read(&smc->queued_smc_hs) >
+				sk->sk_max_ack_backlog)
+		goto drop;
+
+	if (sk_acceptq_is_full(&smc->sk)) {
+		NET_INC_STATS(sock_net(sk), LINUX_MIB_LISTENOVERFLOWS);
+		goto drop;
+	}
+
+	/* passthrough to original syn recv sock fct */
+	child = smc->ori_af_ops->syn_recv_sock(sk, skb, req, dst, req_unhash,
+					       own_req);
+	/* child must not inherit smc or its ops */
+	if (child) {
+		rcu_assign_sk_user_data(child, NULL);
+
+		/* v4-mapped sockets don't inherit parent ops. Don't restore. */
+		if (inet_csk(child)->icsk_af_ops == inet_csk(sk)->icsk_af_ops)
+			inet_csk(child)->icsk_af_ops = smc->ori_af_ops;
+	}
+	return child;
+
+drop:
+	dst_release(dst);
+	tcp_listendrop(sk);
+	return NULL;
+}
+
 static struct smc_hashinfo smc_v4_hashinfo = {
 	.lock = __RW_LOCK_UNLOCKED(smc_v4_hashinfo.lock),
 };
@@ -88,8 +128,8 @@
 
 	write_lock_bh(&h->lock);
 	sk_add_node(sk, head);
-	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 	write_unlock_bh(&h->lock);
+	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
 
 	return 0;
 }
@@ -145,17 +185,21 @@
 
 	if (!smc->use_fallback) {
 		rc = smc_close_active(smc);
-		sock_set_flag(sk, SOCK_DEAD);
+		smc_sock_set_flag(sk, SOCK_DEAD);
 		sk->sk_shutdown |= SHUTDOWN_MASK;
 	} else {
-		if (sk->sk_state != SMC_LISTEN && sk->sk_state != SMC_INIT)
-			sock_put(sk); /* passive closing */
-		if (sk->sk_state == SMC_LISTEN) {
-			/* wake up clcsock accept */
-			rc = kernel_sock_shutdown(smc->clcsock, SHUT_RDWR);
+		if (sk->sk_state != SMC_CLOSED) {
+			if (sk->sk_state != SMC_LISTEN &&
+			    sk->sk_state != SMC_INIT)
+				sock_put(sk); /* passive closing */
+			if (sk->sk_state == SMC_LISTEN) {
+				/* wake up clcsock accept */
+				rc = kernel_sock_shutdown(smc->clcsock,
+							  SHUT_RDWR);
+			}
+			sk->sk_state = SMC_CLOSED;
+			sk->sk_state_change(sk);
 		}
-		sk->sk_state = SMC_CLOSED;
-		sk->sk_state_change(sk);
 		smc_restore_fallback_changes(smc);
 	}
 
@@ -178,7 +222,7 @@
 {
 	struct sock *sk = sock->sk;
 	struct smc_sock *smc;
-	int rc = 0;
+	int old_state, rc = 0;
 
 	if (!sk)
 		goto out;
@@ -186,10 +230,14 @@
 	sock_hold(sk); /* sock_put below */
 	smc = smc_sk(sk);
 
+	old_state = sk->sk_state;
+
 	/* cleanup for a dangling non-blocking connect */
-	if (smc->connect_nonblock && sk->sk_state == SMC_INIT)
+	if (smc->connect_nonblock && old_state == SMC_INIT)
 		tcp_abort(smc->clcsock->sk, ECONNABORTED);
-	flush_work(&smc->connect_work);
+
+	if (cancel_work_sync(&smc->connect_work))
+		sock_put(&smc->sk); /* sock_hold in smc_connect for passive closing */
 
 	if (sk->sk_state == SMC_LISTEN)
 		/* smc_close_non_accepted() is called and acquires
@@ -199,6 +247,10 @@
 	else
 		lock_sock(sk);
 
+	if (old_state == SMC_INIT && sk->sk_state == SMC_ACTIVE &&
+	    !smc->use_fallback)
+		smc_close_active_abort(smc);
+
 	rc = __smc_release(smc);
 
 	/* detach socket */
@@ -386,8 +438,12 @@
 	struct smc_llc_qentry *qentry;
 	int rc;
 
-	/* receive CONFIRM LINK request from server over RoCE fabric */
-	qentry = smc_llc_wait(link->lgr, NULL, SMC_LLC_WAIT_TIME,
+	/* Receive CONFIRM LINK request from server over RoCE fabric.
+	 * Increasing the client's timeout by twice as much as the server's
+	 * timeout by default can temporarily avoid decline messages of
+	 * both sides crossing or colliding
+	 */
+	qentry = smc_llc_wait(link->lgr, NULL, 2 * SMC_LLC_WAIT_TIME,
 			      SMC_LLC_CONFIRM_LINK);
 	if (!qentry) {
 		struct smc_clc_msg_decline dclc;
@@ -439,6 +495,47 @@
 	return 0;
 }
 
+static bool smc_isascii(char *hostname)
+{
+	int i;
+
+	for (i = 0; i < SMC_MAX_HOSTNAME_LEN; i++)
+		if (!isascii(hostname[i]))
+			return false;
+	return true;
+}
+
+static void smc_conn_save_peer_info_fce(struct smc_sock *smc,
+					struct smc_clc_msg_accept_confirm *clc)
+{
+	struct smc_clc_msg_accept_confirm_v2 *clc_v2 =
+		(struct smc_clc_msg_accept_confirm_v2 *)clc;
+	struct smc_clc_first_contact_ext *fce;
+	int clc_v2_len;
+
+	if (clc->hdr.version == SMC_V1 ||
+	    !(clc->hdr.typev2 & SMC_FIRST_CONTACT_MASK))
+		return;
+
+	if (smc->conn.lgr->is_smcd) {
+		memcpy(smc->conn.lgr->negotiated_eid, clc_v2->d1.eid,
+		       SMC_MAX_EID_LEN);
+		clc_v2_len = offsetofend(struct smc_clc_msg_accept_confirm_v2,
+					 d1);
+	} else {
+		memcpy(smc->conn.lgr->negotiated_eid, clc_v2->r1.eid,
+		       SMC_MAX_EID_LEN);
+		clc_v2_len = offsetofend(struct smc_clc_msg_accept_confirm_v2,
+					 r1);
+	}
+	fce = (struct smc_clc_first_contact_ext *)(((u8 *)clc_v2) + clc_v2_len);
+	smc->conn.lgr->peer_os = fce->os_type;
+	smc->conn.lgr->peer_smc_release = fce->release;
+	if (smc_isascii(fce->hostname))
+		memcpy(smc->conn.lgr->peer_hostname, fce->hostname,
+		       SMC_MAX_HOSTNAME_LEN);
+}
+
 static void smcr_conn_save_peer_info(struct smc_sock *smc,
 				     struct smc_clc_msg_accept_confirm *clc)
 {
@@ -451,16 +548,6 @@
 	smc->conn.tx_off = bufsize * (smc->conn.peer_rmbe_idx - 1);
 }
 
-static bool smc_isascii(char *hostname)
-{
-	int i;
-
-	for (i = 0; i < SMC_MAX_HOSTNAME_LEN; i++)
-		if (!isascii(hostname[i]))
-			return false;
-	return true;
-}
-
 static void smcd_conn_save_peer_info(struct smc_sock *smc,
 				     struct smc_clc_msg_accept_confirm *clc)
 {
@@ -472,22 +559,6 @@
 	smc->conn.peer_rmbe_size = bufsize - sizeof(struct smcd_cdc_msg);
 	atomic_set(&smc->conn.peer_rmbe_space, smc->conn.peer_rmbe_size);
 	smc->conn.tx_off = bufsize * smc->conn.peer_rmbe_idx;
-	if (clc->hdr.version > SMC_V1 &&
-	    (clc->hdr.typev2 & SMC_FIRST_CONTACT_MASK)) {
-		struct smc_clc_msg_accept_confirm_v2 *clc_v2 =
-			(struct smc_clc_msg_accept_confirm_v2 *)clc;
-		struct smc_clc_first_contact_ext *fce =
-			(struct smc_clc_first_contact_ext *)
-				(((u8 *)clc_v2) + sizeof(*clc_v2));
-
-		memcpy(smc->conn.lgr->negotiated_eid, clc_v2->eid,
-		       SMC_MAX_EID_LEN);
-		smc->conn.lgr->peer_os = fce->os_type;
-		smc->conn.lgr->peer_smc_release = fce->release;
-		if (smc_isascii(fce->hostname))
-			memcpy(smc->conn.lgr->peer_hostname, fce->hostname,
-			       SMC_MAX_HOSTNAME_LEN);
-	}
 }
 
 static void smc_conn_save_peer_info(struct smc_sock *smc,
@@ -497,14 +568,16 @@
 		smcd_conn_save_peer_info(smc, clc);
 	else
 		smcr_conn_save_peer_info(smc, clc);
+	smc_conn_save_peer_info_fce(smc, clc);
 }
 
 static void smc_link_save_peer_info(struct smc_link *link,
-				    struct smc_clc_msg_accept_confirm *clc)
+				    struct smc_clc_msg_accept_confirm *clc,
+				    struct smc_init_info *ini)
 {
 	link->peer_qpn = ntoh24(clc->r0.qpn);
-	memcpy(link->peer_gid, clc->r0.lcl.gid, SMC_GID_SIZE);
-	memcpy(link->peer_mac, clc->r0.lcl.mac, sizeof(link->peer_mac));
+	memcpy(link->peer_gid, ini->peer_gid, SMC_GID_SIZE);
+	memcpy(link->peer_mac, ini->peer_mac, sizeof(link->peer_mac));
 	link->peer_psn = ntoh24(clc->r0.psn);
 	link->peer_mtu = clc->r0.qp_mtu;
 }
@@ -542,8 +615,118 @@
 	mutex_unlock(&net->smc.mutex_fback_rsn);
 }
 
-static void smc_switch_to_fallback(struct smc_sock *smc, int reason_code)
+/* must be called under rcu read lock */
+static void smc_fback_wakeup_waitqueue(struct smc_sock *smc, void *key)
 {
+	struct socket_wq *wq;
+	__poll_t flags;
+
+	wq = rcu_dereference(smc->sk.sk_wq);
+	if (!skwq_has_sleeper(wq))
+		return;
+
+	/* wake up smc sk->sk_wq */
+	if (!key) {
+		/* sk_state_change */
+		wake_up_interruptible_all(&wq->wait);
+	} else {
+		flags = key_to_poll(key);
+		if (flags & (EPOLLIN | EPOLLOUT))
+			/* sk_data_ready or sk_write_space */
+			wake_up_interruptible_sync_poll(&wq->wait, flags);
+		else if (flags & EPOLLERR)
+			/* sk_error_report */
+			wake_up_interruptible_poll(&wq->wait, flags);
+	}
+}
+
+static int smc_fback_mark_woken(wait_queue_entry_t *wait,
+				unsigned int mode, int sync, void *key)
+{
+	struct smc_mark_woken *mark =
+		container_of(wait, struct smc_mark_woken, wait_entry);
+
+	mark->woken = true;
+	mark->key = key;
+	return 0;
+}
+
+static void smc_fback_forward_wakeup(struct smc_sock *smc, struct sock *clcsk,
+				     void (*clcsock_callback)(struct sock *sk))
+{
+	struct smc_mark_woken mark = { .woken = false };
+	struct socket_wq *wq;
+
+	init_waitqueue_func_entry(&mark.wait_entry,
+				  smc_fback_mark_woken);
+	rcu_read_lock();
+	wq = rcu_dereference(clcsk->sk_wq);
+	if (!wq)
+		goto out;
+	add_wait_queue(sk_sleep(clcsk), &mark.wait_entry);
+	clcsock_callback(clcsk);
+	remove_wait_queue(sk_sleep(clcsk), &mark.wait_entry);
+
+	if (mark.woken)
+		smc_fback_wakeup_waitqueue(smc, mark.key);
+out:
+	rcu_read_unlock();
+}
+
+static void smc_fback_state_change(struct sock *clcsk)
+{
+	struct smc_sock *smc =
+		smc_clcsock_user_data(clcsk);
+
+	if (!smc)
+		return;
+	smc_fback_forward_wakeup(smc, clcsk, smc->clcsk_state_change);
+}
+
+static void smc_fback_data_ready(struct sock *clcsk)
+{
+	struct smc_sock *smc =
+		smc_clcsock_user_data(clcsk);
+
+	if (!smc)
+		return;
+	smc_fback_forward_wakeup(smc, clcsk, smc->clcsk_data_ready);
+}
+
+static void smc_fback_write_space(struct sock *clcsk)
+{
+	struct smc_sock *smc =
+		smc_clcsock_user_data(clcsk);
+
+	if (!smc)
+		return;
+	smc_fback_forward_wakeup(smc, clcsk, smc->clcsk_write_space);
+}
+
+static void smc_fback_error_report(struct sock *clcsk)
+{
+	struct smc_sock *smc =
+		smc_clcsock_user_data(clcsk);
+
+	if (!smc)
+		return;
+	smc_fback_forward_wakeup(smc, clcsk, smc->clcsk_error_report);
+}
+
+static int smc_switch_to_fallback(struct smc_sock *smc, int reason_code)
+{
+	struct sock *clcsk;
+	int rc = 0;
+
+	mutex_lock(&smc->clcsock_release_lock);
+	if (!smc->clcsock) {
+		rc = -EBADF;
+		goto out;
+	}
+	clcsk = smc->clcsock->sk;
+
+	if (smc->use_fallback)
+		goto out;
 	smc->use_fallback = true;
 	smc->fallback_rsn = reason_code;
 	smc_stat_fallback(smc);
@@ -552,13 +735,42 @@
 		smc->clcsock->file->private_data = smc->clcsock;
 		smc->clcsock->wq.fasync_list =
 			smc->sk.sk_socket->wq.fasync_list;
+
+		/* There might be some wait entries remaining
+		 * in smc sk->sk_wq and they should be woken up
+		 * as clcsock's wait queue is woken up.
+		 */
+		smc->clcsk_state_change = clcsk->sk_state_change;
+		smc->clcsk_data_ready = clcsk->sk_data_ready;
+		smc->clcsk_write_space = clcsk->sk_write_space;
+		smc->clcsk_error_report = clcsk->sk_error_report;
+
+		clcsk->sk_state_change = smc_fback_state_change;
+		clcsk->sk_data_ready = smc_fback_data_ready;
+		clcsk->sk_write_space = smc_fback_write_space;
+		clcsk->sk_error_report = smc_fback_error_report;
+
+		smc->clcsock->sk->sk_user_data =
+			(void *)((uintptr_t)smc | SK_USER_DATA_NOCOPY);
 	}
+out:
+	mutex_unlock(&smc->clcsock_release_lock);
+	return rc;
 }
 
 /* fall back during connect */
 static int smc_connect_fallback(struct smc_sock *smc, int reason_code)
 {
-	smc_switch_to_fallback(smc, reason_code);
+	struct net *net = sock_net(&smc->sk);
+	int rc = 0;
+
+	rc = smc_switch_to_fallback(smc, reason_code);
+	if (rc) { /* fallback fails */
+		this_cpu_inc(net->smc.smc_stats->clnt_hshake_err_cnt);
+		if (smc->sk.sk_state == SMC_INIT)
+			sock_put(&smc->sk); /* passive closing */
+		return rc;
+	}
 	smc_copy_sock_settings_to_clc(smc);
 	smc->connect_nonblock = 0;
 	if (smc->sk.sk_state == SMC_INIT)
@@ -593,10 +805,12 @@
 
 static void smc_conn_abort(struct smc_sock *smc, int local_first)
 {
+	struct smc_connection *conn = &smc->conn;
+	struct smc_link_group *lgr = conn->lgr;
+
+	smc_conn_free(conn);
 	if (local_first)
-		smc_lgr_cleanup_early(&smc->conn);
-	else
-		smc_conn_free(&smc->conn);
+		smc_lgr_cleanup_early(lgr);
 }
 
 /* check if there is a rdma device available for this connection. */
@@ -608,7 +822,9 @@
 	 * used for the internal TCP socket
 	 */
 	smc_pnet_find_roce_resource(smc->clcsock->sk, ini);
-	if (!ini->ib_dev)
+	if (!ini->check_smcrv2 && !ini->ib_dev)
+		return SMC_CLC_DECL_NOSMCRDEV;
+	if (ini->check_smcrv2 && !ini->smcrv2.ib_dev_v2)
 		return SMC_CLC_DECL_NOSMCRDEV;
 	return 0;
 }
@@ -692,27 +908,42 @@
 	int rc = 0;
 
 	/* check if there is an ism device available */
-	if (ini->smcd_version & SMC_V1) {
-		if (smc_find_ism_device(smc, ini) ||
-		    smc_connect_ism_vlan_setup(smc, ini)) {
-			if (ini->smc_type_v1 == SMC_TYPE_B)
-				ini->smc_type_v1 = SMC_TYPE_R;
-			else
-				ini->smc_type_v1 = SMC_TYPE_N;
-		} /* else ISM V1 is supported for this connection */
-		if (smc_find_rdma_device(smc, ini)) {
-			if (ini->smc_type_v1 == SMC_TYPE_B)
-				ini->smc_type_v1 = SMC_TYPE_D;
-			else
-				ini->smc_type_v1 = SMC_TYPE_N;
-		} /* else RDMA is supported for this connection */
-	}
-	if (smc_ism_is_v2_capable() && smc_find_ism_v2_device_clnt(smc, ini))
-		ini->smc_type_v2 = SMC_TYPE_N;
+	if (!(ini->smcd_version & SMC_V1) ||
+	    smc_find_ism_device(smc, ini) ||
+	    smc_connect_ism_vlan_setup(smc, ini))
+		ini->smcd_version &= ~SMC_V1;
+	/* else ISM V1 is supported for this connection */
+
+	/* check if there is an rdma device available */
+	if (!(ini->smcr_version & SMC_V1) ||
+	    smc_find_rdma_device(smc, ini))
+		ini->smcr_version &= ~SMC_V1;
+	/* else RDMA is supported for this connection */
+
+	ini->smc_type_v1 = smc_indicated_type(ini->smcd_version & SMC_V1,
+					      ini->smcr_version & SMC_V1);
+
+	/* check if there is an ism v2 device available */
+	if (!(ini->smcd_version & SMC_V2) ||
+	    !smc_ism_is_v2_capable() ||
+	    smc_find_ism_v2_device_clnt(smc, ini))
+		ini->smcd_version &= ~SMC_V2;
+
+	/* check if there is an rdma v2 device available */
+	ini->check_smcrv2 = true;
+	ini->smcrv2.saddr = smc->clcsock->sk->sk_rcv_saddr;
+	if (!(ini->smcr_version & SMC_V2) ||
+	    smc->clcsock->sk->sk_family != AF_INET ||
+	    !smc_clc_ueid_count() ||
+	    smc_find_rdma_device(smc, ini))
+		ini->smcr_version &= ~SMC_V2;
+	ini->check_smcrv2 = false;
+
+	ini->smc_type_v2 = smc_indicated_type(ini->smcd_version & SMC_V2,
+					      ini->smcr_version & SMC_V2);
 
 	/* if neither ISM nor RDMA are supported, fallback */
-	if (!smcr_indicated(ini->smc_type_v1) &&
-	    ini->smc_type_v1 == SMC_TYPE_N && ini->smc_type_v2 == SMC_TYPE_N)
+	if (ini->smc_type_v1 == SMC_TYPE_N && ini->smc_type_v2 == SMC_TYPE_N)
 		rc = SMC_CLC_DECL_NOSMCDEV;
 
 	return rc;
@@ -752,6 +983,64 @@
 				SMC_CLC_ACCEPT, CLC_WAIT_TIME);
 }
 
+void smc_fill_gid_list(struct smc_link_group *lgr,
+		       struct smc_gidlist *gidlist,
+		       struct smc_ib_device *known_dev, u8 *known_gid)
+{
+	struct smc_init_info *alt_ini = NULL;
+
+	memset(gidlist, 0, sizeof(*gidlist));
+	memcpy(gidlist->list[gidlist->len++], known_gid, SMC_GID_SIZE);
+
+	alt_ini = kzalloc(sizeof(*alt_ini), GFP_KERNEL);
+	if (!alt_ini)
+		goto out;
+
+	alt_ini->vlan_id = lgr->vlan_id;
+	alt_ini->check_smcrv2 = true;
+	alt_ini->smcrv2.saddr = lgr->saddr;
+	smc_pnet_find_alt_roce(lgr, alt_ini, known_dev);
+
+	if (!alt_ini->smcrv2.ib_dev_v2)
+		goto out;
+
+	memcpy(gidlist->list[gidlist->len++], alt_ini->smcrv2.ib_gid_v2,
+	       SMC_GID_SIZE);
+
+out:
+	kfree(alt_ini);
+}
+
+static int smc_connect_rdma_v2_prepare(struct smc_sock *smc,
+				       struct smc_clc_msg_accept_confirm *aclc,
+				       struct smc_init_info *ini)
+{
+	struct smc_clc_msg_accept_confirm_v2 *clc_v2 =
+		(struct smc_clc_msg_accept_confirm_v2 *)aclc;
+	struct smc_clc_first_contact_ext *fce =
+		(struct smc_clc_first_contact_ext *)
+			(((u8 *)clc_v2) + sizeof(*clc_v2));
+
+	if (!ini->first_contact_peer || aclc->hdr.version == SMC_V1)
+		return 0;
+
+	if (fce->v2_direct) {
+		memcpy(ini->smcrv2.nexthop_mac, &aclc->r0.lcl.mac, ETH_ALEN);
+		ini->smcrv2.uses_gateway = false;
+	} else {
+		if (smc_ib_find_route(smc->clcsock->sk->sk_rcv_saddr,
+				      smc_ib_gid_to_ipv4(aclc->r0.lcl.gid),
+				      ini->smcrv2.nexthop_mac,
+				      &ini->smcrv2.uses_gateway))
+			return SMC_CLC_DECL_NOROUTE;
+		if (!ini->smcrv2.uses_gateway) {
+			/* mismatch: peer claims indirect, but its direct */
+			return SMC_CLC_DECL_NOINDIRECT;
+		}
+	}
+	return 0;
+}
+
 /* setup for RDMA connection of client */
 static int smc_connect_rdma(struct smc_sock *smc,
 			    struct smc_clc_msg_accept_confirm *aclc,
@@ -759,11 +1048,18 @@
 {
 	int i, reason_code = 0;
 	struct smc_link *link;
+	u8 *eid = NULL;
 
 	ini->is_smcd = false;
-	ini->ib_lcl = &aclc->r0.lcl;
 	ini->ib_clcqpn = ntoh24(aclc->r0.qpn);
 	ini->first_contact_peer = aclc->hdr.typev2 & SMC_FIRST_CONTACT_MASK;
+	memcpy(ini->peer_systemid, aclc->r0.lcl.id_for_peer, SMC_SYSTEMID_LEN);
+	memcpy(ini->peer_gid, aclc->r0.lcl.gid, SMC_GID_SIZE);
+	memcpy(ini->peer_mac, aclc->r0.lcl.mac, ETH_ALEN);
+
+	reason_code = smc_connect_rdma_v2_prepare(smc, aclc, ini);
+	if (reason_code)
+		return reason_code;
 
 	mutex_lock(&smc_client_lgr_pending);
 	reason_code = smc_conn_create(smc, ini);
@@ -785,8 +1081,9 @@
 			if (l->peer_qpn == ntoh24(aclc->r0.qpn) &&
 			    !memcmp(l->peer_gid, &aclc->r0.lcl.gid,
 				    SMC_GID_SIZE) &&
-			    !memcmp(l->peer_mac, &aclc->r0.lcl.mac,
-				    sizeof(l->peer_mac))) {
+			    (aclc->hdr.version > SMC_V1 ||
+			     !memcmp(l->peer_mac, &aclc->r0.lcl.mac,
+				     sizeof(l->peer_mac)))) {
 				link = l;
 				break;
 			}
@@ -805,7 +1102,7 @@
 	}
 
 	if (ini->first_contact_local)
-		smc_link_save_peer_info(link, aclc);
+		smc_link_save_peer_info(link, aclc, ini);
 
 	if (smc_rmb_rtoken_handling(&smc->conn, link, aclc)) {
 		reason_code = SMC_CLC_DECL_ERR_RTOK;
@@ -828,8 +1125,18 @@
 	}
 	smc_rmb_sync_sg_for_device(&smc->conn);
 
+	if (aclc->hdr.version > SMC_V1) {
+		struct smc_clc_msg_accept_confirm_v2 *clc_v2 =
+			(struct smc_clc_msg_accept_confirm_v2 *)aclc;
+
+		eid = clc_v2->r1.eid;
+		if (ini->first_contact_local)
+			smc_fill_gid_list(link->lgr, &ini->smcrv2.gidlist,
+					  link->smcibdev, link->gid);
+	}
+
 	reason_code = smc_clc_send_confirm(smc, ini->first_contact_local,
-					   SMC_V1);
+					   aclc->hdr.version, eid, ini);
 	if (reason_code)
 		goto connect_abort;
 
@@ -869,7 +1176,7 @@
 	int i;
 
 	for (i = 0; i < ini->ism_offered_cnt + 1; i++) {
-		if (ini->ism_chid[i] == ntohs(aclc->chid)) {
+		if (ini->ism_chid[i] == ntohs(aclc->d1.chid)) {
 			ini->ism_selected = i;
 			return 0;
 		}
@@ -883,6 +1190,7 @@
 			   struct smc_clc_msg_accept_confirm *aclc,
 			   struct smc_init_info *ini)
 {
+	u8 *eid = NULL;
 	int rc = 0;
 
 	ini->is_smcd = true;
@@ -918,8 +1226,15 @@
 	smc_rx_init(smc);
 	smc_tx_init(smc);
 
+	if (aclc->hdr.version > SMC_V1) {
+		struct smc_clc_msg_accept_confirm_v2 *clc_v2 =
+			(struct smc_clc_msg_accept_confirm_v2 *)aclc;
+
+		eid = clc_v2->d1.eid;
+	}
+
 	rc = smc_clc_send_confirm(smc, ini->first_contact_local,
-				  aclc->hdr.version);
+				  aclc->hdr.version, eid, NULL);
 	if (rc)
 		goto connect_abort;
 	mutex_unlock(&smc_server_lgr_pending);
@@ -942,17 +1257,24 @@
 static int smc_connect_check_aclc(struct smc_init_info *ini,
 				  struct smc_clc_msg_accept_confirm *aclc)
 {
-	if ((aclc->hdr.typev1 == SMC_TYPE_R &&
-	     !smcr_indicated(ini->smc_type_v1)) ||
-	    (aclc->hdr.typev1 == SMC_TYPE_D &&
-	     ((!smcd_indicated(ini->smc_type_v1) &&
-	       !smcd_indicated(ini->smc_type_v2)) ||
-	      (aclc->hdr.version == SMC_V1 &&
-	       !smcd_indicated(ini->smc_type_v1)) ||
-	      (aclc->hdr.version == SMC_V2 &&
-	       !smcd_indicated(ini->smc_type_v2)))))
+	if (aclc->hdr.typev1 != SMC_TYPE_R &&
+	    aclc->hdr.typev1 != SMC_TYPE_D)
 		return SMC_CLC_DECL_MODEUNSUPP;
 
+	if (aclc->hdr.version >= SMC_V2) {
+		if ((aclc->hdr.typev1 == SMC_TYPE_R &&
+		     !smcr_indicated(ini->smc_type_v2)) ||
+		    (aclc->hdr.typev1 == SMC_TYPE_D &&
+		     !smcd_indicated(ini->smc_type_v2)))
+			return SMC_CLC_DECL_MODEUNSUPP;
+	} else {
+		if ((aclc->hdr.typev1 == SMC_TYPE_R &&
+		     !smcr_indicated(ini->smc_type_v1)) ||
+		    (aclc->hdr.typev1 == SMC_TYPE_D &&
+		     !smcd_indicated(ini->smc_type_v1)))
+			return SMC_CLC_DECL_MODEUNSUPP;
+	}
+
 	return 0;
 }
 
@@ -983,14 +1305,15 @@
 		return smc_connect_decline_fallback(smc, SMC_CLC_DECL_MEM,
 						    version);
 
-	ini->smcd_version = SMC_V1;
-	ini->smcd_version |= smc_ism_is_v2_capable() ? SMC_V2 : 0;
+	ini->smcd_version = SMC_V1 | SMC_V2;
+	ini->smcr_version = SMC_V1 | SMC_V2;
 	ini->smc_type_v1 = SMC_TYPE_B;
-	ini->smc_type_v2 = smc_ism_is_v2_capable() ? SMC_TYPE_D : SMC_TYPE_N;
+	ini->smc_type_v2 = SMC_TYPE_B;
 
 	/* get vlan id from IP device */
 	if (smc_vlan_by_tcpsk(smc->clcsock, ini)) {
 		ini->smcd_version &= ~SMC_V1;
+		ini->smcr_version = 0;
 		ini->smc_type_v1 = SMC_TYPE_N;
 		if (!ini->smcd_version) {
 			rc = SMC_CLC_DECL_GETVLANERR;
@@ -1018,15 +1341,17 @@
 	/* check if smc modes and versions of CLC proposal and accept match */
 	rc = smc_connect_check_aclc(ini, aclc);
 	version = aclc->hdr.version == SMC_V1 ? SMC_V1 : SMC_V2;
-	ini->smcd_version = version;
 	if (rc)
 		goto vlan_cleanup;
 
 	/* depending on previous steps, connect using rdma or ism */
-	if (aclc->hdr.typev1 == SMC_TYPE_R)
+	if (aclc->hdr.typev1 == SMC_TYPE_R) {
+		ini->smcr_version = version;
 		rc = smc_connect_rdma(smc, aclc, ini);
-	else if (aclc->hdr.typev1 == SMC_TYPE_D)
+	} else if (aclc->hdr.typev1 == SMC_TYPE_D) {
+		ini->smcd_version = version;
 		rc = smc_connect_ism(smc, aclc, ini);
+	}
 	if (rc)
 		goto vlan_cleanup;
 
@@ -1070,6 +1395,8 @@
 		smc->sk.sk_state = SMC_CLOSED;
 		if (rc == -EPIPE || rc == -EAGAIN)
 			smc->sk.sk_err = EPIPE;
+		else if (rc == -ECONNREFUSED)
+			smc->sk.sk_err = ECONNREFUSED;
 		else if (signal_pending(current))
 			smc->sk.sk_err = -sock_intr_errno(timeo);
 		sock_put(&smc->sk); /* passive closing */
@@ -1128,9 +1455,9 @@
 	if (rc && rc != -EINPROGRESS)
 		goto out;
 
-	sock_hold(&smc->sk); /* sock put in passive closing */
 	if (smc->use_fallback)
 		goto out;
+	sock_hold(&smc->sk); /* sock put in passive closing */
 	if (flags & O_NONBLOCK) {
 		if (queue_work(smc_hs_wq, &smc->connect_work))
 			smc->connect_nonblock = 1;
@@ -1179,7 +1506,7 @@
 		if (new_clcsock)
 			sock_release(new_clcsock);
 		new_sk->sk_state = SMC_CLOSED;
-		sock_set_flag(new_sk, SOCK_DEAD);
+		smc_sock_set_flag(new_sk, SOCK_DEAD);
 		sock_put(new_sk); /* final */
 		*new_smc = NULL;
 		goto out;
@@ -1307,7 +1634,7 @@
 	smcr_lgr_set_type(link->lgr, SMC_LGR_SINGLE);
 
 	/* initial contact - try to establish second link */
-	smc_llc_srv_add_link(link);
+	smc_llc_srv_add_link(link, NULL);
 	return 0;
 }
 
@@ -1317,6 +1644,10 @@
 	struct smc_sock *lsmc = new_smc->listen_smc;
 	struct sock *newsmcsk = &new_smc->sk;
 
+	if (tcp_sk(new_smc->clcsock->sk)->syn_smc)
+		atomic_dec(&lsmc->queued_smc_hs);
+
+	release_sock(newsmcsk); /* lock in smc_listen_work() */
 	if (lsmc->sk.sk_state == SMC_LISTEN) {
 		lock_sock_nested(&lsmc->sk, SINGLE_DEPTH_NESTING);
 		smc_accept_enqueue(&lsmc->sk, newsmcsk);
@@ -1335,7 +1666,6 @@
 {
 	struct sock *newsmcsk = &new_smc->sk;
 
-	sk_refcnt_debug_inc(newsmcsk);
 	if (newsmcsk->sk_state == SMC_INIT)
 		newsmcsk->sk_state = SMC_ACTIVE;
 
@@ -1362,11 +1692,12 @@
 {
 	/* RDMA setup failed, switch back to TCP */
 	smc_conn_abort(new_smc, local_first);
-	if (reason_code < 0) { /* error, no fallback possible */
+	if (reason_code < 0 ||
+	    smc_switch_to_fallback(new_smc, reason_code)) {
+		/* error, no fallback possible */
 		smc_listen_out_err(new_smc);
 		return;
 	}
-	smc_switch_to_fallback(new_smc, reason_code);
 	if (reason_code && reason_code != SMC_CLC_DECL_PEERDECL) {
 		if (smc_clc_send_decline(new_smc, reason_code, version) < 0) {
 			smc_listen_out_err(new_smc);
@@ -1387,33 +1718,48 @@
 
 	ini->smc_type_v1 = pclc->hdr.typev1;
 	ini->smc_type_v2 = pclc->hdr.typev2;
-	ini->smcd_version = ini->smc_type_v1 != SMC_TYPE_N ? SMC_V1 : 0;
-	if (pclc->hdr.version > SMC_V1)
-		ini->smcd_version |=
-				ini->smc_type_v2 != SMC_TYPE_N ? SMC_V2 : 0;
-	if (!(ini->smcd_version & SMC_V2)) {
-		rc = SMC_CLC_DECL_PEERNOSMC;
-		goto out;
+	ini->smcd_version = smcd_indicated(ini->smc_type_v1) ? SMC_V1 : 0;
+	ini->smcr_version = smcr_indicated(ini->smc_type_v1) ? SMC_V1 : 0;
+	if (pclc->hdr.version > SMC_V1) {
+		if (smcd_indicated(ini->smc_type_v2))
+			ini->smcd_version |= SMC_V2;
+		if (smcr_indicated(ini->smc_type_v2))
+			ini->smcr_version |= SMC_V2;
 	}
-	if (!smc_ism_is_v2_capable()) {
-		ini->smcd_version &= ~SMC_V2;
-		rc = SMC_CLC_DECL_NOISM2SUPP;
+	if (!(ini->smcd_version & SMC_V2) && !(ini->smcr_version & SMC_V2)) {
+		rc = SMC_CLC_DECL_PEERNOSMC;
 		goto out;
 	}
 	pclc_v2_ext = smc_get_clc_v2_ext(pclc);
 	if (!pclc_v2_ext) {
 		ini->smcd_version &= ~SMC_V2;
+		ini->smcr_version &= ~SMC_V2;
 		rc = SMC_CLC_DECL_NOV2EXT;
 		goto out;
 	}
 	pclc_smcd_v2_ext = smc_get_clc_smcd_v2_ext(pclc_v2_ext);
-	if (!pclc_smcd_v2_ext) {
-		ini->smcd_version &= ~SMC_V2;
-		rc = SMC_CLC_DECL_NOV2DEXT;
+	if (ini->smcd_version & SMC_V2) {
+		if (!smc_ism_is_v2_capable()) {
+			ini->smcd_version &= ~SMC_V2;
+			rc = SMC_CLC_DECL_NOISM2SUPP;
+		} else if (!pclc_smcd_v2_ext) {
+			ini->smcd_version &= ~SMC_V2;
+			rc = SMC_CLC_DECL_NOV2DEXT;
+		} else if (!pclc_v2_ext->hdr.eid_cnt &&
+			   !pclc_v2_ext->hdr.flag.seid) {
+			ini->smcd_version &= ~SMC_V2;
+			rc = SMC_CLC_DECL_NOUEID;
+		}
+	}
+	if (ini->smcr_version & SMC_V2) {
+		if (!pclc_v2_ext->hdr.eid_cnt) {
+			ini->smcr_version &= ~SMC_V2;
+			rc = SMC_CLC_DECL_NOUEID;
+		}
 	}
 
 out:
-	if (!ini->smcd_version)
+	if (!ini->smcd_version && !ini->smcr_version)
 		return rc;
 
 	return 0;
@@ -1429,6 +1775,8 @@
 	if (pclc->hdr.typev1 == SMC_TYPE_N)
 		return 0;
 	pclc_prfx = smc_clc_proposal_get_prefix(pclc);
+	if (!pclc_prfx)
+		return -EPROTO;
 	if (smc_clc_prfx_match(newclcsock, pclc_prfx))
 		return SMC_CLC_DECL_DIFFPREFIX;
 
@@ -1533,11 +1881,6 @@
 	pclc_smcd = smc_get_clc_msg_smcd(pclc);
 	smc_v2_ext = smc_get_clc_v2_ext(pclc);
 	smcd_v2_ext = smc_get_clc_smcd_v2_ext(smc_v2_ext);
-	if (!smcd_v2_ext ||
-	    !smc_v2_ext->hdr.flag.seid) { /* no system EID support for SMCD */
-		smc_find_ism_store_rc(SMC_CLC_DECL_NOSEID, ini);
-		goto not_found;
-	}
 
 	mutex_lock(&smcd_dev_list.mutex);
 	if (pclc_smcd->ism.chid)
@@ -1555,14 +1898,16 @@
 	}
 	mutex_unlock(&smcd_dev_list.mutex);
 
-	if (ini->ism_dev[0]) {
-		smc_ism_get_system_eid(ini->ism_dev[0], &eid);
-		if (memcmp(eid, smcd_v2_ext->system_eid, SMC_MAX_EID_LEN))
-			goto not_found;
-	} else {
+	if (!ini->ism_dev[0]) {
+		smc_find_ism_store_rc(SMC_CLC_DECL_NOSMCD2DEV, ini);
 		goto not_found;
 	}
 
+	smc_ism_get_system_eid(&eid);
+	if (!smc_clc_match_eid(ini->negotiated_eid, smc_v2_ext,
+			       smcd_v2_ext->system_eid, eid))
+		goto not_found;
+
 	/* separate - outside the smcd_dev_list.lock */
 	smcd_version = ini->smcd_version;
 	for (i = 0; i < matches; i++) {
@@ -1579,6 +1924,7 @@
 	}
 	/* no V2 ISM device could be initialized */
 	ini->smcd_version = smcd_version;	/* restore original value */
+	ini->negotiated_eid[0] = 0;
 
 not_found:
 	ini->smcd_version &= ~SMC_V2;
@@ -1594,7 +1940,9 @@
 	int rc = 0;
 
 	/* check if ISM V1 is available */
-	if (!(ini->smcd_version & SMC_V1) || !smcd_indicated(ini->smc_type_v1))
+	if (!(ini->smcd_version & SMC_V1) ||
+	    !smcd_indicated(ini->smc_type_v1) ||
+	    !pclc_smcd)
 		goto not_found;
 	ini->is_smcd = true; /* prepare ISM check */
 	ini->ism_peer_gid[0] = ntohll(pclc_smcd->ism.gid);
@@ -1608,6 +1956,7 @@
 
 not_found:
 	smc_find_ism_store_rc(rc, ini);
+	ini->smcd_version &= ~SMC_V1;
 	ini->ism_dev[0] = NULL;
 	ini->is_smcd = false;
 }
@@ -1626,24 +1975,69 @@
 	return 0;
 }
 
+static void smc_find_rdma_v2_device_serv(struct smc_sock *new_smc,
+					 struct smc_clc_msg_proposal *pclc,
+					 struct smc_init_info *ini)
+{
+	struct smc_clc_v2_extension *smc_v2_ext;
+	u8 smcr_version;
+	int rc;
+
+	if (!(ini->smcr_version & SMC_V2) || !smcr_indicated(ini->smc_type_v2))
+		goto not_found;
+
+	smc_v2_ext = smc_get_clc_v2_ext(pclc);
+	if (!smc_clc_match_eid(ini->negotiated_eid, smc_v2_ext, NULL, NULL))
+		goto not_found;
+
+	/* prepare RDMA check */
+	memcpy(ini->peer_systemid, pclc->lcl.id_for_peer, SMC_SYSTEMID_LEN);
+	memcpy(ini->peer_gid, smc_v2_ext->roce, SMC_GID_SIZE);
+	memcpy(ini->peer_mac, pclc->lcl.mac, ETH_ALEN);
+	ini->check_smcrv2 = true;
+	ini->smcrv2.clc_sk = new_smc->clcsock->sk;
+	ini->smcrv2.saddr = new_smc->clcsock->sk->sk_rcv_saddr;
+	ini->smcrv2.daddr = smc_ib_gid_to_ipv4(smc_v2_ext->roce);
+	rc = smc_find_rdma_device(new_smc, ini);
+	if (rc) {
+		smc_find_ism_store_rc(rc, ini);
+		goto not_found;
+	}
+	if (!ini->smcrv2.uses_gateway)
+		memcpy(ini->smcrv2.nexthop_mac, pclc->lcl.mac, ETH_ALEN);
+
+	smcr_version = ini->smcr_version;
+	ini->smcr_version = SMC_V2;
+	rc = smc_listen_rdma_init(new_smc, ini);
+	if (!rc)
+		rc = smc_listen_rdma_reg(new_smc, ini->first_contact_local);
+	if (!rc)
+		return;
+	ini->smcr_version = smcr_version;
+	smc_find_ism_store_rc(rc, ini);
+
+not_found:
+	ini->smcr_version &= ~SMC_V2;
+	ini->check_smcrv2 = false;
+}
+
 static int smc_find_rdma_v1_device_serv(struct smc_sock *new_smc,
 					struct smc_clc_msg_proposal *pclc,
 					struct smc_init_info *ini)
 {
 	int rc;
 
-	if (!smcr_indicated(ini->smc_type_v1))
+	if (!(ini->smcr_version & SMC_V1) || !smcr_indicated(ini->smc_type_v1))
 		return SMC_CLC_DECL_NOSMCDEV;
 
 	/* prepare RDMA check */
-	ini->ib_lcl = &pclc->lcl;
+	memcpy(ini->peer_systemid, pclc->lcl.id_for_peer, SMC_SYSTEMID_LEN);
+	memcpy(ini->peer_gid, pclc->lcl.gid, SMC_GID_SIZE);
+	memcpy(ini->peer_mac, pclc->lcl.mac, ETH_ALEN);
 	rc = smc_find_rdma_device(new_smc, ini);
 	if (rc) {
 		/* no RDMA device found */
-		if (ini->smc_type_v1 == SMC_TYPE_B)
-			/* neither ISM nor RDMA device found */
-			rc = SMC_CLC_DECL_NOSMCDEV;
-		return rc;
+		return SMC_CLC_DECL_NOSMCDEV;
 	}
 	rc = smc_listen_rdma_init(new_smc, ini);
 	if (rc)
@@ -1656,51 +2050,60 @@
 				  struct smc_clc_msg_proposal *pclc,
 				  struct smc_init_info *ini)
 {
-	int rc;
+	int prfx_rc;
 
 	/* check for ISM device matching V2 proposed device */
 	smc_find_ism_v2_device_serv(new_smc, pclc, ini);
 	if (ini->ism_dev[0])
 		return 0;
 
-	if (!(ini->smcd_version & SMC_V1))
-		return ini->rc ?: SMC_CLC_DECL_NOSMCD2DEV;
-
-	/* check for matching IP prefix and subnet length */
-	rc = smc_listen_prfx_check(new_smc, pclc);
-	if (rc)
-		return ini->rc ?: rc;
+	/* check for matching IP prefix and subnet length (V1) */
+	prfx_rc = smc_listen_prfx_check(new_smc, pclc);
+	if (prfx_rc)
+		smc_find_ism_store_rc(prfx_rc, ini);
 
 	/* get vlan id from IP device */
 	if (smc_vlan_by_tcpsk(new_smc->clcsock, ini))
 		return ini->rc ?: SMC_CLC_DECL_GETVLANERR;
 
 	/* check for ISM device matching V1 proposed device */
-	smc_find_ism_v1_device_serv(new_smc, pclc, ini);
+	if (!prfx_rc)
+		smc_find_ism_v1_device_serv(new_smc, pclc, ini);
 	if (ini->ism_dev[0])
 		return 0;
 
-	if (pclc->hdr.typev1 == SMC_TYPE_D)
+	if (!smcr_indicated(pclc->hdr.typev1) &&
+	    !smcr_indicated(pclc->hdr.typev2))
 		/* skip RDMA and decline */
 		return ini->rc ?: SMC_CLC_DECL_NOSMCDDEV;
 
-	/* check if RDMA is available */
-	rc = smc_find_rdma_v1_device_serv(new_smc, pclc, ini);
-	smc_find_ism_store_rc(rc, ini);
+	/* check if RDMA V2 is available */
+	smc_find_rdma_v2_device_serv(new_smc, pclc, ini);
+	if (ini->smcrv2.ib_dev_v2)
+		return 0;
 
-	return (!rc) ? 0 : ini->rc;
+	/* check if RDMA V1 is available */
+	if (!prfx_rc) {
+		int rc;
+
+		rc = smc_find_rdma_v1_device_serv(new_smc, pclc, ini);
+		smc_find_ism_store_rc(rc, ini);
+		return (!rc) ? 0 : ini->rc;
+	}
+	return SMC_CLC_DECL_NOSMCDEV;
 }
 
 /* listen worker: finish RDMA setup */
 static int smc_listen_rdma_finish(struct smc_sock *new_smc,
 				  struct smc_clc_msg_accept_confirm *cclc,
-				  bool local_first)
+				  bool local_first,
+				  struct smc_init_info *ini)
 {
 	struct smc_link *link = new_smc->conn.lnk;
 	int reason_code = 0;
 
 	if (local_first)
-		smc_link_save_peer_info(link, cclc);
+		smc_link_save_peer_info(link, cclc, ini);
 
 	if (smc_rmb_rtoken_handling(&new_smc->conn, link, cclc))
 		return SMC_CLC_DECL_ERR_RTOK;
@@ -1721,14 +2124,16 @@
 {
 	struct smc_sock *new_smc = container_of(work, struct smc_sock,
 						smc_listen_work);
-	u8 version = smc_ism_is_v2_capable() ? SMC_V2 : SMC_V1;
 	struct socket *newclcsock = new_smc->clcsock;
 	struct smc_clc_msg_accept_confirm *cclc;
 	struct smc_clc_msg_proposal_area *buf;
 	struct smc_clc_msg_proposal *pclc;
 	struct smc_init_info *ini = NULL;
+	u8 proposal_version = SMC_V1;
+	u8 accept_version;
 	int rc = 0;
 
+	lock_sock(&new_smc->sk); /* release in smc_listen_out() */
 	if (new_smc->listen_smc->sk.sk_state != SMC_LISTEN)
 		return smc_listen_out_err(new_smc);
 
@@ -1739,8 +2144,11 @@
 
 	/* check if peer is smc capable */
 	if (!tcp_sk(newclcsock->sk)->syn_smc) {
-		smc_switch_to_fallback(new_smc, SMC_CLC_DECL_PEERNOSMC);
-		smc_listen_out_connected(new_smc);
+		rc = smc_switch_to_fallback(new_smc, SMC_CLC_DECL_PEERNOSMC);
+		if (rc)
+			smc_listen_out_err(new_smc);
+		else
+			smc_listen_out_connected(new_smc);
 		return;
 	}
 
@@ -1757,7 +2165,9 @@
 			      SMC_CLC_PROPOSAL, CLC_WAIT_TIME);
 	if (rc)
 		goto out_decl;
-	version = pclc->hdr.version == SMC_V1 ? SMC_V1 : version;
+
+	if (pclc->hdr.version > SMC_V1)
+		proposal_version = SMC_V2;
 
 	/* IPSec connections opt out of SMC optimizations */
 	if (using_ipsec(new_smc)) {
@@ -1787,8 +2197,9 @@
 		goto out_unlock;
 
 	/* send SMC Accept CLC message */
+	accept_version = ini->is_smcd ? ini->smcd_version : ini->smcr_version;
 	rc = smc_clc_send_accept(new_smc, ini->first_contact_local,
-				 ini->smcd_version == SMC_V2 ? SMC_V2 : SMC_V1);
+				 accept_version, ini->negotiated_eid);
 	if (rc)
 		goto out_unlock;
 
@@ -1810,7 +2221,7 @@
 	/* finish worker */
 	if (!ini->is_smcd) {
 		rc = smc_listen_rdma_finish(new_smc, cclc,
-					    ini->first_contact_local);
+					    ini->first_contact_local, ini);
 		if (rc)
 			goto out_unlock;
 		mutex_unlock(&smc_server_lgr_pending);
@@ -1824,7 +2235,7 @@
 	mutex_unlock(&smc_server_lgr_pending);
 out_decl:
 	smc_listen_decline(new_smc, rc, ini ? ini->first_contact_local : 0,
-			   version);
+			   proposal_version);
 out_free:
 	kfree(ini);
 	kfree(buf);
@@ -1846,6 +2257,9 @@
 		if (!new_smc)
 			continue;
 
+		if (tcp_sk(new_smc->clcsock->sk)->syn_smc)
+			atomic_inc(&lsmc->queued_smc_hs);
+
 		new_smc->listen_smc = lsmc;
 		new_smc->use_fallback = lsmc->use_fallback;
 		new_smc->fallback_rsn = lsmc->fallback_rsn;
@@ -1866,10 +2280,9 @@
 
 static void smc_clcsock_data_ready(struct sock *listen_clcsock)
 {
-	struct smc_sock *lsmc;
+	struct smc_sock *lsmc =
+		smc_clcsock_user_data(listen_clcsock);
 
-	lsmc = (struct smc_sock *)
-	       ((uintptr_t)listen_clcsock->sk_user_data & ~SK_USER_DATA_NOCOPY);
 	if (!lsmc)
 		return;
 	lsmc->clcsk_data_ready(listen_clcsock);
@@ -1913,9 +2326,20 @@
 	smc->clcsock->sk->sk_data_ready = smc_clcsock_data_ready;
 	smc->clcsock->sk->sk_user_data =
 		(void *)((uintptr_t)smc | SK_USER_DATA_NOCOPY);
+
+	/* save original ops */
+	smc->ori_af_ops = inet_csk(smc->clcsock->sk)->icsk_af_ops;
+
+	smc->af_ops = *smc->ori_af_ops;
+	smc->af_ops.syn_recv_sock = smc_tcp_syn_recv_sock;
+
+	inet_csk(smc->clcsock->sk)->icsk_af_ops = &smc->af_ops;
+
 	rc = kernel_listen(smc->clcsock, backlog);
-	if (rc)
+	if (rc) {
+		smc->clcsock->sk->sk_data_ready = smc->clcsk_data_ready;
 		goto out;
+	}
 	sk->sk_max_ack_backlog = backlog;
 	sk->sk_ack_backlog = 0;
 	sk->sk_state = SMC_LISTEN;
@@ -1985,7 +2409,7 @@
 			release_sock(clcsk);
 		} else if (!atomic_read(&smc_sk(nsk)->conn.bytes_to_rcv)) {
 			lock_sock(nsk);
-			smc_rx_wait(smc_sk(nsk), &timeo, smc_rx_data_available);
+			smc_rx_wait(smc_sk(nsk), &timeo, 0, smc_rx_data_available);
 			release_sock(nsk);
 		}
 	}
@@ -2013,22 +2437,27 @@
 {
 	struct sock *sk = sock->sk;
 	struct smc_sock *smc;
-	int rc = -EPIPE;
+	int rc;
 
 	smc = smc_sk(sk);
 	lock_sock(sk);
-	if ((sk->sk_state != SMC_ACTIVE) &&
-	    (sk->sk_state != SMC_APPCLOSEWAIT1) &&
-	    (sk->sk_state != SMC_INIT))
-		goto out;
 
+	/* SMC does not support connect with fastopen */
 	if (msg->msg_flags & MSG_FASTOPEN) {
+		/* not connected yet, fallback */
 		if (sk->sk_state == SMC_INIT && !smc->connect_nonblock) {
-			smc_switch_to_fallback(smc, SMC_CLC_DECL_OPTUNSUPP);
+			rc = smc_switch_to_fallback(smc, SMC_CLC_DECL_OPTUNSUPP);
+			if (rc)
+				goto out;
 		} else {
 			rc = -EINVAL;
 			goto out;
 		}
+	} else if ((sk->sk_state != SMC_ACTIVE) &&
+		   (sk->sk_state != SMC_APPCLOSEWAIT1) &&
+		   (sk->sk_state != SMC_INIT)) {
+		rc = -EPIPE;
+		goto out;
 	}
 
 	if (smc->use_fallback) {
@@ -2130,6 +2559,13 @@
 			} else {
 				sk_set_bit(SOCKWQ_ASYNC_NOSPACE, sk);
 				set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
+
+				if (sk->sk_state != SMC_INIT) {
+					/* Race breaker the same way as tcp_poll(). */
+					smp_mb__after_atomic();
+					if (atomic_read(&smc->conn.sndbuf_space))
+						mask |= EPOLLOUT | EPOLLWRNORM;
+				}
 			}
 			if (atomic_read(&smc->conn.bytes_to_rcv))
 				mask |= EPOLLIN | EPOLLRDNORM;
@@ -2148,8 +2584,10 @@
 static int smc_shutdown(struct socket *sock, int how)
 {
 	struct sock *sk = sock->sk;
+	bool do_shutdown = true;
 	struct smc_sock *smc;
 	int rc = -EINVAL;
+	int old_state;
 	int rc1 = 0;
 
 	smc = smc_sk(sk);
@@ -2170,13 +2608,19 @@
 	if (smc->use_fallback) {
 		rc = kernel_sock_shutdown(smc->clcsock, how);
 		sk->sk_shutdown = smc->clcsock->sk->sk_shutdown;
-		if (sk->sk_shutdown == SHUTDOWN_MASK)
+		if (sk->sk_shutdown == SHUTDOWN_MASK) {
 			sk->sk_state = SMC_CLOSED;
+			sock_put(sk);
+		}
 		goto out;
 	}
 	switch (how) {
 	case SHUT_RDWR:		/* shutdown in both directions */
+		old_state = sk->sk_state;
 		rc = smc_close_active(smc);
+		if (old_state == SMC_ACTIVE &&
+		    sk->sk_state == SMC_PEERCLOSEWAIT1)
+			do_shutdown = false;
 		break;
 	case SHUT_WR:
 		rc = smc_close_shutdown_write(smc);
@@ -2186,7 +2630,7 @@
 		/* nothing more to do because peer is not involved */
 		break;
 	}
-	if (smc->clcsock)
+	if (do_shutdown && smc->clcsock)
 		rc1 = kernel_sock_shutdown(smc->clcsock, how);
 	/* map sock_shutdown_cmd constants to sk_shutdown value range */
 	sk->sk_shutdown |= how + 1;
@@ -2211,6 +2655,11 @@
 	/* generic setsockopts reaching us here always apply to the
 	 * CLC socket
 	 */
+	mutex_lock(&smc->clcsock_release_lock);
+	if (!smc->clcsock) {
+		mutex_unlock(&smc->clcsock_release_lock);
+		return -EBADF;
+	}
 	if (unlikely(!smc->clcsock->ops->setsockopt))
 		rc = -EOPNOTSUPP;
 	else
@@ -2220,6 +2669,7 @@
 		sk->sk_err = smc->clcsock->sk->sk_err;
 		sk_error_report(sk);
 	}
+	mutex_unlock(&smc->clcsock_release_lock);
 
 	if (optlen < sizeof(int))
 		return -EINVAL;
@@ -2236,7 +2686,7 @@
 	case TCP_FASTOPEN_NO_COOKIE:
 		/* option not supported by SMC */
 		if (sk->sk_state == SMC_INIT && !smc->connect_nonblock) {
-			smc_switch_to_fallback(smc, SMC_CLC_DECL_OPTUNSUPP);
+			rc = smc_switch_to_fallback(smc, SMC_CLC_DECL_OPTUNSUPP);
 		} else {
 			rc = -EINVAL;
 		}
@@ -2247,8 +2697,8 @@
 		    sk->sk_state != SMC_CLOSED) {
 			if (val) {
 				SMC_STAT_INC(smc, ndly_cnt);
-				mod_delayed_work(smc->conn.lgr->tx_wq,
-						 &smc->conn.tx_work, 0);
+				smc_tx_pending(&smc->conn);
+				cancel_delayed_work(&smc->conn.tx_work);
 			}
 		}
 		break;
@@ -2258,8 +2708,8 @@
 		    sk->sk_state != SMC_CLOSED) {
 			if (!val) {
 				SMC_STAT_INC(smc, cork_cnt);
-				mod_delayed_work(smc->conn.lgr->tx_wq,
-						 &smc->conn.tx_work, 0);
+				smc_tx_pending(&smc->conn);
+				cancel_delayed_work(&smc->conn.tx_work);
 			}
 		}
 		break;
@@ -2279,13 +2729,23 @@
 			  char __user *optval, int __user *optlen)
 {
 	struct smc_sock *smc;
+	int rc;
 
 	smc = smc_sk(sock->sk);
+	mutex_lock(&smc->clcsock_release_lock);
+	if (!smc->clcsock) {
+		mutex_unlock(&smc->clcsock_release_lock);
+		return -EBADF;
+	}
 	/* socket options apply to the CLC socket */
-	if (unlikely(!smc->clcsock->ops->getsockopt))
+	if (unlikely(!smc->clcsock->ops->getsockopt)) {
+		mutex_unlock(&smc->clcsock_release_lock);
 		return -EOPNOTSUPP;
-	return smc->clcsock->ops->getsockopt(smc->clcsock, level, optname,
-					     optval, optlen);
+	}
+	rc = smc->clcsock->ops->getsockopt(smc->clcsock, level, optname,
+					   optval, optlen);
+	mutex_unlock(&smc->clcsock_release_lock);
+	return rc;
 }
 
 static int smc_ioctl(struct socket *sock, unsigned int cmd,
@@ -2559,14 +3019,14 @@
 
 	rc = register_pernet_subsys(&smc_net_stat_ops);
 	if (rc)
-		return rc;
+		goto out_pernet_subsys;
 
 	smc_ism_init();
 	smc_clc_init();
 
 	rc = smc_nl_init();
 	if (rc)
-		goto out_pernet_subsys;
+		goto out_pernet_subsys_stat;
 
 	rc = smc_pnet_init();
 	if (rc)
@@ -2644,6 +3104,8 @@
 	smc_pnet_exit();
 out_nl:
 	smc_nl_exit();
+out_pernet_subsys_stat:
+	unregister_pernet_subsys(&smc_net_stat_ops);
 out_pernet_subsys:
 	unregister_pernet_subsys(&smc_net_ops);
 
@@ -2662,6 +3124,7 @@
 	proto_unregister(&smc_proto);
 	smc_pnet_exit();
 	smc_nl_exit();
+	smc_clc_exit();
 	unregister_pernet_subsys(&smc_net_stat_ops);
 	unregister_pernet_subsys(&smc_net_ops);
 	rcu_barrier();
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc.h
@@ -29,9 +29,6 @@
 					 * devices
 					 */
 
-#define SMC_MAX_HOSTNAME_LEN	32
-#define SMC_MAX_EID_LEN		32
-
 extern struct proto smc_proto;
 extern struct proto smc_proto6;
 
@@ -59,7 +56,20 @@
 struct smc_link_group;
 
 struct smc_wr_rx_hdr {	/* common prefix part of LLC and CDC to demultiplex */
-	u8			type;
+	union {
+		u8 type;
+#if defined(__BIG_ENDIAN_BITFIELD)
+		struct {
+			u8 llc_version:4,
+			   llc_type:4;
+		};
+#elif defined(__LITTLE_ENDIAN_BITFIELD)
+		struct {
+			u8 llc_type:4,
+			   llc_version:4;
+		};
+#endif
+	};
 } __aligned(1);
 
 struct smc_cdc_conn_state_flags {
@@ -129,6 +139,12 @@
 	SMC_URG_READ	= 3,			/* data was already read */
 };
 
+struct smc_mark_woken {
+	bool woken;
+	void *key;
+	wait_queue_entry_t wait_entry;
+};
+
 struct smc_connection {
 	struct rb_node		alert_node;
 	struct smc_link_group	*lgr;		/* link group of connection */
@@ -170,6 +186,11 @@
 	u16			tx_cdc_seq;	/* sequence # for CDC send */
 	u16			tx_cdc_seq_fin;	/* sequence # - tx completed */
 	spinlock_t		send_lock;	/* protect wr_sends */
+	atomic_t		cdc_pend_tx_wr; /* number of pending tx CDC wqe
+						 * - inc when post wqe,
+						 * - dec on polled tx cqe
+						 */
+	wait_queue_head_t	cdc_pend_tx_wq; /* wakeup on no cdc_pend_tx_wr*/
 	struct delayed_work	tx_work;	/* retry of smc_cdc_msg_send */
 	u32			tx_off;		/* base offset in peer rmb */
 
@@ -212,8 +233,14 @@
 struct smc_sock {				/* smc sock container */
 	struct sock		sk;
 	struct socket		*clcsock;	/* internal tcp socket */
+	void			(*clcsk_state_change)(struct sock *sk);
+						/* original stat_change fct. */
 	void			(*clcsk_data_ready)(struct sock *sk);
-						/* original data_ready fct. **/
+						/* original data_ready fct. */
+	void			(*clcsk_write_space)(struct sock *sk);
+						/* original write_space fct. */
+	void			(*clcsk_error_report)(struct sock *sk);
+						/* original error_report fct. */
 	struct smc_connection	conn;		/* smc connection */
 	struct smc_sock		*listen_smc;	/* listen parent */
 	struct work_struct	connect_work;	/* handle non-blocking connect*/
@@ -224,6 +251,10 @@
 	bool			use_fallback;	/* fallback to tcp */
 	int			fallback_rsn;	/* reason for fallback */
 	u32			peer_diagnosis; /* decline reason from peer */
+	atomic_t                queued_smc_hs;  /* queued smc handshakes */
+	struct inet_connection_sock_af_ops		af_ops;
+	const struct inet_connection_sock_af_ops	*ori_af_ops;
+						/* original af ops */
 	int			sockopt_defer_accept;
 						/* sockopt TCP_DEFER_ACCEPT
 						 * value
@@ -248,6 +279,12 @@
 	return (struct smc_sock *)sk;
 }
 
+static inline struct smc_sock *smc_clcsock_user_data(const struct sock *clcsk)
+{
+	return (struct smc_sock *)
+	       ((uintptr_t)clcsk->sk_user_data & ~SK_USER_DATA_NOCOPY);
+}
+
 extern struct workqueue_struct	*smc_hs_wq;	/* wq for handshake work */
 extern struct workqueue_struct	*smc_close_wq;	/* wq for close work */
 
@@ -289,7 +326,17 @@
 }
 #endif
 
+struct smc_gidlist;
+
 struct sock *smc_accept_dequeue(struct sock *parent, struct socket *new_sock);
 void smc_close_non_accepted(struct sock *sk);
+void smc_fill_gid_list(struct smc_link_group *lgr,
+		       struct smc_gidlist *gidlist,
+		       struct smc_ib_device *known_dev, u8 *known_gid);
+
+static inline void smc_sock_set_flag(struct sock *sk, enum sock_flags flag)
+{
+	set_bit(flag, &sk->sk_flags);
+}
 
 #endif	/* __SMC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_cdc.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_cdc.c
@@ -28,17 +28,15 @@
 {
 	struct smc_cdc_tx_pend *cdcpend = (struct smc_cdc_tx_pend *)pnd_snd;
 	struct smc_connection *conn = cdcpend->conn;
+	struct smc_buf_desc *sndbuf_desc;
 	struct smc_sock *smc;
 	int diff;
 
-	if (!conn)
-		/* already dismissed */
-		return;
-
+	sndbuf_desc = conn->sndbuf_desc;
 	smc = container_of(conn, struct smc_sock, conn);
 	bh_lock_sock(&smc->sk);
-	if (!wc_status) {
-		diff = smc_curs_diff(cdcpend->conn->sndbuf_desc->len,
+	if (!wc_status && sndbuf_desc) {
+		diff = smc_curs_diff(sndbuf_desc->len,
 				     &cdcpend->conn->tx_curs_fin,
 				     &cdcpend->cursor);
 		/* sndbuf_space is decreased in smc_sendmsg */
@@ -51,6 +49,12 @@
 			      conn);
 		conn->tx_cdc_seq_fin = cdcpend->ctrl_seq;
 	}
+
+	if (atomic_dec_and_test(&conn->cdc_pend_tx_wr) &&
+	    unlikely(wq_has_sleeper(&conn->cdc_pend_tx_wq)))
+		wake_up(&conn->cdc_pend_tx_wq);
+	WARN_ON(atomic_read(&conn->cdc_pend_tx_wr) < 0);
+
 	smc_tx_sndbuf_nonfull(smc);
 	bh_unlock_sock(&smc->sk);
 }
@@ -70,7 +74,7 @@
 		/* abnormal termination */
 		if (!rc)
 			smc_wr_tx_put_slot(link,
-					   (struct smc_wr_tx_pend_priv *)pend);
+					   (struct smc_wr_tx_pend_priv *)(*pend));
 		rc = -EPIPE;
 	}
 	return rc;
@@ -107,6 +111,10 @@
 	conn->tx_cdc_seq++;
 	conn->local_tx_ctrl.seqno = conn->tx_cdc_seq;
 	smc_host_msg_to_cdc((struct smc_cdc_msg *)wr_buf, conn, &cfed);
+
+	atomic_inc(&conn->cdc_pend_tx_wr);
+	smp_mb__after_atomic(); /* Make sure cdc_pend_tx_wr added before post */
+
 	rc = smc_wr_tx_send(link, (struct smc_wr_tx_pend_priv *)pend);
 	if (!rc) {
 		smc_curs_copy(&conn->rx_curs_confirmed, &cfed, conn);
@@ -114,6 +122,7 @@
 	} else {
 		conn->tx_cdc_seq--;
 		conn->local_tx_ctrl.seqno = conn->tx_cdc_seq;
+		atomic_dec(&conn->cdc_pend_tx_wr);
 	}
 
 	return rc;
@@ -136,7 +145,18 @@
 	peer->token = htonl(local->token);
 	peer->prod_flags.failover_validation = 1;
 
+	/* We need to set pend->conn here to make sure smc_cdc_tx_handler()
+	 * can handle properly
+	 */
+	smc_cdc_add_pending_send(conn, pend);
+
+	atomic_inc(&conn->cdc_pend_tx_wr);
+	smp_mb__after_atomic(); /* Make sure cdc_pend_tx_wr added before post */
+
 	rc = smc_wr_tx_send(link, (struct smc_wr_tx_pend_priv *)pend);
+	if (unlikely(rc))
+		atomic_dec(&conn->cdc_pend_tx_wr);
+
 	return rc;
 }
 
@@ -193,31 +213,9 @@
 	return rc;
 }
 
-static bool smc_cdc_tx_filter(struct smc_wr_tx_pend_priv *tx_pend,
-			      unsigned long data)
+void smc_cdc_wait_pend_tx_wr(struct smc_connection *conn)
 {
-	struct smc_connection *conn = (struct smc_connection *)data;
-	struct smc_cdc_tx_pend *cdc_pend =
-		(struct smc_cdc_tx_pend *)tx_pend;
-
-	return cdc_pend->conn == conn;
-}
-
-static void smc_cdc_tx_dismisser(struct smc_wr_tx_pend_priv *tx_pend)
-{
-	struct smc_cdc_tx_pend *cdc_pend =
-		(struct smc_cdc_tx_pend *)tx_pend;
-
-	cdc_pend->conn = NULL;
-}
-
-void smc_cdc_tx_dismiss_slots(struct smc_connection *conn)
-{
-	struct smc_link *link = conn->lnk;
-
-	smc_wr_tx_dismiss_slots(link, SMC_CDC_MSG_TYPE,
-				smc_cdc_tx_filter, smc_cdc_tx_dismisser,
-				(unsigned long)conn);
+	wait_event(conn->cdc_pend_tx_wq, !atomic_read(&conn->cdc_pend_tx_wr));
 }
 
 /* Send a SMC-D CDC header.
@@ -371,7 +369,7 @@
 		smc->sk.sk_shutdown |= RCV_SHUTDOWN;
 		if (smc->clcsock && smc->clcsock->sk)
 			smc->clcsock->sk->sk_shutdown |= RCV_SHUTDOWN;
-		sock_set_flag(&smc->sk, SOCK_DONE);
+		smc_sock_set_flag(&smc->sk, SOCK_DONE);
 		sock_hold(&smc->sk); /* sock_put in close_work */
 		if (!queue_work(smc_close_wq, &conn->close_work))
 			sock_put(&smc->sk);
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_cdc.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_cdc.h
@@ -291,7 +291,7 @@
 			  struct smc_wr_buf **wr_buf,
 			  struct smc_rdma_wr **wr_rdma_buf,
 			  struct smc_cdc_tx_pend **pend);
-void smc_cdc_tx_dismiss_slots(struct smc_connection *conn);
+void smc_cdc_wait_pend_tx_wr(struct smc_connection *conn);
 int smc_cdc_msg_send(struct smc_connection *conn, struct smc_wr_buf *wr_buf,
 		     struct smc_cdc_tx_pend *pend);
 int smc_cdc_get_slot_and_msg_send(struct smc_connection *conn);
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_clc.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_clc.c
@@ -26,10 +26,12 @@
 #include "smc_clc.h"
 #include "smc_ib.h"
 #include "smc_ism.h"
+#include "smc_netlink.h"
 
 #define SMCR_CLC_ACCEPT_CONFIRM_LEN 68
 #define SMCD_CLC_ACCEPT_CONFIRM_LEN 48
 #define SMCD_CLC_ACCEPT_CONFIRM_LEN_V2 78
+#define SMCR_CLC_ACCEPT_CONFIRM_LEN_V2 108
 #define SMC_CLC_RECV_BUF_LEN	100
 
 /* eye catcher "SMCR" EBCDIC for CLC messages */
@@ -39,6 +41,297 @@
 
 static u8 smc_hostname[SMC_MAX_HOSTNAME_LEN];
 
+struct smc_clc_eid_table {
+	rwlock_t lock;
+	struct list_head list;
+	u8 ueid_cnt;
+	u8 seid_enabled;
+};
+
+static struct smc_clc_eid_table smc_clc_eid_table;
+
+struct smc_clc_eid_entry {
+	struct list_head list;
+	u8 eid[SMC_MAX_EID_LEN];
+};
+
+/* The size of a user EID is 32 characters.
+ * Valid characters should be (single-byte character set) A-Z, 0-9, '.' and '-'.
+ * Blanks should only be used to pad to the expected size.
+ * First character must be alphanumeric.
+ */
+static bool smc_clc_ueid_valid(char *ueid)
+{
+	char *end = ueid + SMC_MAX_EID_LEN;
+
+	while (--end >= ueid && isspace(*end))
+		;
+	if (end < ueid)
+		return false;
+	if (!isalnum(*ueid) || islower(*ueid))
+		return false;
+	while (ueid <= end) {
+		if ((!isalnum(*ueid) || islower(*ueid)) && *ueid != '.' &&
+		    *ueid != '-')
+			return false;
+		ueid++;
+	}
+	return true;
+}
+
+static int smc_clc_ueid_add(char *ueid)
+{
+	struct smc_clc_eid_entry *new_ueid, *tmp_ueid;
+	int rc;
+
+	if (!smc_clc_ueid_valid(ueid))
+		return -EINVAL;
+
+	/* add a new ueid entry to the ueid table if there isn't one */
+	new_ueid = kzalloc(sizeof(*new_ueid), GFP_KERNEL);
+	if (!new_ueid)
+		return -ENOMEM;
+	memcpy(new_ueid->eid, ueid, SMC_MAX_EID_LEN);
+
+	write_lock(&smc_clc_eid_table.lock);
+	if (smc_clc_eid_table.ueid_cnt >= SMC_MAX_UEID) {
+		rc = -ERANGE;
+		goto err_out;
+	}
+	list_for_each_entry(tmp_ueid, &smc_clc_eid_table.list, list) {
+		if (!memcmp(tmp_ueid->eid, ueid, SMC_MAX_EID_LEN)) {
+			rc = -EEXIST;
+			goto err_out;
+		}
+	}
+	list_add_tail(&new_ueid->list, &smc_clc_eid_table.list);
+	smc_clc_eid_table.ueid_cnt++;
+	write_unlock(&smc_clc_eid_table.lock);
+	return 0;
+
+err_out:
+	write_unlock(&smc_clc_eid_table.lock);
+	kfree(new_ueid);
+	return rc;
+}
+
+int smc_clc_ueid_count(void)
+{
+	int count;
+
+	read_lock(&smc_clc_eid_table.lock);
+	count = smc_clc_eid_table.ueid_cnt;
+	read_unlock(&smc_clc_eid_table.lock);
+
+	return count;
+}
+
+int smc_nl_add_ueid(struct sk_buff *skb, struct genl_info *info)
+{
+	struct nlattr *nla_ueid = info->attrs[SMC_NLA_EID_TABLE_ENTRY];
+	char *ueid;
+
+	if (!nla_ueid || nla_len(nla_ueid) != SMC_MAX_EID_LEN + 1)
+		return -EINVAL;
+	ueid = (char *)nla_data(nla_ueid);
+
+	return smc_clc_ueid_add(ueid);
+}
+
+/* remove one or all ueid entries from the table */
+static int smc_clc_ueid_remove(char *ueid)
+{
+	struct smc_clc_eid_entry *lst_ueid, *tmp_ueid;
+	int rc = -ENOENT;
+
+	/* remove table entry */
+	write_lock(&smc_clc_eid_table.lock);
+	list_for_each_entry_safe(lst_ueid, tmp_ueid, &smc_clc_eid_table.list,
+				 list) {
+		if (!ueid || !memcmp(lst_ueid->eid, ueid, SMC_MAX_EID_LEN)) {
+			list_del(&lst_ueid->list);
+			smc_clc_eid_table.ueid_cnt--;
+			kfree(lst_ueid);
+			rc = 0;
+		}
+	}
+	if (!rc && !smc_clc_eid_table.ueid_cnt) {
+		smc_clc_eid_table.seid_enabled = 1;
+		rc = -EAGAIN;	/* indicate success and enabling of seid */
+	}
+	write_unlock(&smc_clc_eid_table.lock);
+	return rc;
+}
+
+int smc_nl_remove_ueid(struct sk_buff *skb, struct genl_info *info)
+{
+	struct nlattr *nla_ueid = info->attrs[SMC_NLA_EID_TABLE_ENTRY];
+	char *ueid;
+
+	if (!nla_ueid || nla_len(nla_ueid) != SMC_MAX_EID_LEN + 1)
+		return -EINVAL;
+	ueid = (char *)nla_data(nla_ueid);
+
+	return smc_clc_ueid_remove(ueid);
+}
+
+int smc_nl_flush_ueid(struct sk_buff *skb, struct genl_info *info)
+{
+	smc_clc_ueid_remove(NULL);
+	return 0;
+}
+
+static int smc_nl_ueid_dumpinfo(struct sk_buff *skb, u32 portid, u32 seq,
+				u32 flags, char *ueid)
+{
+	char ueid_str[SMC_MAX_EID_LEN + 1];
+	void *hdr;
+
+	hdr = genlmsg_put(skb, portid, seq, &smc_gen_nl_family,
+			  flags, SMC_NETLINK_DUMP_UEID);
+	if (!hdr)
+		return -ENOMEM;
+	snprintf(ueid_str, sizeof(ueid_str), "%s", ueid);
+	if (nla_put_string(skb, SMC_NLA_EID_TABLE_ENTRY, ueid_str)) {
+		genlmsg_cancel(skb, hdr);
+		return -EMSGSIZE;
+	}
+	genlmsg_end(skb, hdr);
+	return 0;
+}
+
+static int _smc_nl_ueid_dump(struct sk_buff *skb, u32 portid, u32 seq,
+			     int start_idx)
+{
+	struct smc_clc_eid_entry *lst_ueid;
+	int idx = 0;
+
+	read_lock(&smc_clc_eid_table.lock);
+	list_for_each_entry(lst_ueid, &smc_clc_eid_table.list, list) {
+		if (idx++ < start_idx)
+			continue;
+		if (smc_nl_ueid_dumpinfo(skb, portid, seq, NLM_F_MULTI,
+					 lst_ueid->eid)) {
+			--idx;
+			break;
+		}
+	}
+	read_unlock(&smc_clc_eid_table.lock);
+	return idx;
+}
+
+int smc_nl_dump_ueid(struct sk_buff *skb, struct netlink_callback *cb)
+{
+	struct smc_nl_dmp_ctx *cb_ctx = smc_nl_dmp_ctx(cb);
+	int idx;
+
+	idx = _smc_nl_ueid_dump(skb, NETLINK_CB(cb->skb).portid,
+				cb->nlh->nlmsg_seq, cb_ctx->pos[0]);
+
+	cb_ctx->pos[0] = idx;
+	return skb->len;
+}
+
+int smc_nl_dump_seid(struct sk_buff *skb, struct netlink_callback *cb)
+{
+	struct smc_nl_dmp_ctx *cb_ctx = smc_nl_dmp_ctx(cb);
+	char seid_str[SMC_MAX_EID_LEN + 1];
+	u8 seid_enabled;
+	void *hdr;
+	u8 *seid;
+
+	if (cb_ctx->pos[0])
+		return skb->len;
+
+	hdr = genlmsg_put(skb, NETLINK_CB(cb->skb).portid, cb->nlh->nlmsg_seq,
+			  &smc_gen_nl_family, NLM_F_MULTI,
+			  SMC_NETLINK_DUMP_SEID);
+	if (!hdr)
+		return -ENOMEM;
+	if (!smc_ism_is_v2_capable())
+		goto end;
+
+	smc_ism_get_system_eid(&seid);
+	snprintf(seid_str, sizeof(seid_str), "%s", seid);
+	if (nla_put_string(skb, SMC_NLA_SEID_ENTRY, seid_str))
+		goto err;
+	read_lock(&smc_clc_eid_table.lock);
+	seid_enabled = smc_clc_eid_table.seid_enabled;
+	read_unlock(&smc_clc_eid_table.lock);
+	if (nla_put_u8(skb, SMC_NLA_SEID_ENABLED, seid_enabled))
+		goto err;
+end:
+	genlmsg_end(skb, hdr);
+	cb_ctx->pos[0]++;
+	return skb->len;
+err:
+	genlmsg_cancel(skb, hdr);
+	return -EMSGSIZE;
+}
+
+int smc_nl_enable_seid(struct sk_buff *skb, struct genl_info *info)
+{
+	write_lock(&smc_clc_eid_table.lock);
+	smc_clc_eid_table.seid_enabled = 1;
+	write_unlock(&smc_clc_eid_table.lock);
+	return 0;
+}
+
+int smc_nl_disable_seid(struct sk_buff *skb, struct genl_info *info)
+{
+	int rc = 0;
+
+	write_lock(&smc_clc_eid_table.lock);
+	if (!smc_clc_eid_table.ueid_cnt)
+		rc = -ENOENT;
+	else
+		smc_clc_eid_table.seid_enabled = 0;
+	write_unlock(&smc_clc_eid_table.lock);
+	return rc;
+}
+
+static bool _smc_clc_match_ueid(u8 *peer_ueid)
+{
+	struct smc_clc_eid_entry *tmp_ueid;
+
+	list_for_each_entry(tmp_ueid, &smc_clc_eid_table.list, list) {
+		if (!memcmp(tmp_ueid->eid, peer_ueid, SMC_MAX_EID_LEN))
+			return true;
+	}
+	return false;
+}
+
+bool smc_clc_match_eid(u8 *negotiated_eid,
+		       struct smc_clc_v2_extension *smc_v2_ext,
+		       u8 *peer_eid, u8 *local_eid)
+{
+	bool match = false;
+	int i;
+
+	negotiated_eid[0] = 0;
+	read_lock(&smc_clc_eid_table.lock);
+	if (peer_eid && local_eid &&
+	    smc_clc_eid_table.seid_enabled &&
+	    smc_v2_ext->hdr.flag.seid &&
+	    !memcmp(peer_eid, local_eid, SMC_MAX_EID_LEN)) {
+		memcpy(negotiated_eid, peer_eid, SMC_MAX_EID_LEN);
+		match = true;
+		goto out;
+	}
+
+	for (i = 0; i < smc_v2_ext->hdr.eid_cnt; i++) {
+		if (_smc_clc_match_ueid(smc_v2_ext->user_eids[i])) {
+			memcpy(negotiated_eid, smc_v2_ext->user_eids[i],
+			       SMC_MAX_EID_LEN);
+			match = true;
+			goto out;
+		}
+	}
+out:
+	read_unlock(&smc_clc_eid_table.lock);
+	return match;
+}
+
 /* check arriving CLC proposal */
 static bool smc_clc_msg_prop_valid(struct smc_clc_msg_proposal *pclc)
 {
@@ -49,6 +342,10 @@
 
 	v2_ext = smc_get_clc_v2_ext(pclc);
 	pclc_prfx = smc_clc_proposal_get_prefix(pclc);
+	if (!pclc_prfx ||
+	    pclc_prfx->ipv6_prefixes_cnt > SMC_CLC_MAX_V6_PREFIX)
+		return false;
+
 	if (hdr->version == SMC_V1) {
 		if (hdr->typev1 == SMC_TYPE_N)
 			return false;
@@ -100,6 +397,27 @@
 		    (ntohs(hdr->length) != SMCD_CLC_ACCEPT_CONFIRM_LEN_V2 +
 				sizeof(struct smc_clc_first_contact_ext)))
 			return false;
+		if (hdr->typev1 == SMC_TYPE_R &&
+		    ntohs(hdr->length) < SMCR_CLC_ACCEPT_CONFIRM_LEN_V2)
+			return false;
+	}
+	return true;
+}
+
+/* check arriving CLC decline */
+static bool
+smc_clc_msg_decl_valid(struct smc_clc_msg_decline *dclc)
+{
+	struct smc_clc_msg_hdr *hdr = &dclc->hdr;
+
+	if (hdr->typev1 != SMC_TYPE_R && hdr->typev1 != SMC_TYPE_D)
+		return false;
+	if (hdr->version == SMC_V1) {
+		if (ntohs(hdr->length) != sizeof(struct smc_clc_msg_decline))
+			return false;
+	} else {
+		if (ntohs(hdr->length) != sizeof(struct smc_clc_msg_decline_v2))
+			return false;
 	}
 	return true;
 }
@@ -145,9 +463,9 @@
 		break;
 	case SMC_CLC_DECLINE:
 		dclc = (struct smc_clc_msg_decline *)clcm;
-		if (ntohs(dclc->hdr.length) != sizeof(*dclc))
+		if (!smc_clc_msg_decl_valid(dclc))
 			return false;
-		trl = &dclc->trl;
+		check_trl = false;
 		break;
 	default:
 		return false;
@@ -423,6 +741,11 @@
 						SMC_CLC_RECV_BUF_LEN : datlen;
 		iov_iter_kvec(&msg.msg_iter, READ, &vec, 1, recvlen);
 		len = sock_recvmsg(smc->clcsock, &msg, krflags);
+		if (len < recvlen) {
+			smc->sk.sk_err = EPROTO;
+			reason_code = -EPROTO;
+			goto out;
+		}
 		datlen -= len;
 	}
 	if (clcm->type == SMC_CLC_DECLINE) {
@@ -446,15 +769,16 @@
 /* send CLC DECLINE message across internal TCP socket */
 int smc_clc_send_decline(struct smc_sock *smc, u32 peer_diag_info, u8 version)
 {
-	struct smc_clc_msg_decline dclc;
+	struct smc_clc_msg_decline *dclc_v1;
+	struct smc_clc_msg_decline_v2 dclc;
 	struct msghdr msg;
+	int len, send_len;
 	struct kvec vec;
-	int len;
 
+	dclc_v1 = (struct smc_clc_msg_decline *)&dclc;
 	memset(&dclc, 0, sizeof(dclc));
 	memcpy(dclc.hdr.eyecatcher, SMC_EYECATCHER, sizeof(SMC_EYECATCHER));
 	dclc.hdr.type = SMC_CLC_DECLINE;
-	dclc.hdr.length = htons(sizeof(struct smc_clc_msg_decline));
 	dclc.hdr.version = version;
 	dclc.os_type = version == SMC_V1 ? 0 : SMC_CLC_OS_LINUX;
 	dclc.hdr.typev2 = (peer_diag_info == SMC_CLC_DECL_SYNCERR) ?
@@ -464,14 +788,22 @@
 		memcpy(dclc.id_for_peer, local_systemid,
 		       sizeof(local_systemid));
 	dclc.peer_diagnosis = htonl(peer_diag_info);
-	memcpy(dclc.trl.eyecatcher, SMC_EYECATCHER, sizeof(SMC_EYECATCHER));
+	if (version == SMC_V1) {
+		memcpy(dclc_v1->trl.eyecatcher, SMC_EYECATCHER,
+		       sizeof(SMC_EYECATCHER));
+		send_len = sizeof(*dclc_v1);
+	} else {
+		memcpy(dclc.trl.eyecatcher, SMC_EYECATCHER,
+		       sizeof(SMC_EYECATCHER));
+		send_len = sizeof(dclc);
+	}
+	dclc.hdr.length = htons(send_len);
 
 	memset(&msg, 0, sizeof(msg));
 	vec.iov_base = &dclc;
-	vec.iov_len = sizeof(struct smc_clc_msg_decline);
-	len = kernel_sendmsg(smc->clcsock, &msg, &vec, 1,
-			     sizeof(struct smc_clc_msg_decline));
-	if (len < 0 || len < sizeof(struct smc_clc_msg_decline))
+	vec.iov_len = send_len;
+	len = kernel_sendmsg(smc->clcsock, &msg, &vec, 1, send_len);
+	if (len < 0 || len < send_len)
 		len = -EPROTO;
 	return len > 0 ? 0 : len;
 }
@@ -551,9 +883,10 @@
 	if (ini->smc_type_v2 == SMC_TYPE_N) {
 		pclc_smcd->v2_ext_offset = 0;
 	} else {
+		struct smc_clc_eid_entry *ueident;
 		u16 v2_ext_offset;
-		u8 *eid = NULL;
 
+		v2_ext->hdr.flag.release = SMC_RELEASE;
 		v2_ext_offset = sizeof(*pclc_smcd) -
 			offsetofend(struct smc_clc_msg_smcd, v2_ext_offset);
 		if (ini->smc_type_v1 != SMC_TYPE_N)
@@ -561,21 +894,31 @@
 						pclc_prfx->ipv6_prefixes_cnt *
 						sizeof(ipv6_prfx[0]);
 		pclc_smcd->v2_ext_offset = htons(v2_ext_offset);
-		v2_ext->hdr.eid_cnt = 0;
+		plen += sizeof(*v2_ext);
+
+		read_lock(&smc_clc_eid_table.lock);
+		v2_ext->hdr.eid_cnt = smc_clc_eid_table.ueid_cnt;
+		plen += smc_clc_eid_table.ueid_cnt * SMC_MAX_EID_LEN;
+		i = 0;
+		list_for_each_entry(ueident, &smc_clc_eid_table.list, list) {
+			memcpy(v2_ext->user_eids[i++], ueident->eid,
+			       sizeof(ueident->eid));
+		}
+		read_unlock(&smc_clc_eid_table.lock);
+	}
+	if (smcd_indicated(ini->smc_type_v2)) {
+		u8 *eid = NULL;
+
+		v2_ext->hdr.flag.seid = smc_clc_eid_table.seid_enabled;
 		v2_ext->hdr.ism_gid_cnt = ini->ism_offered_cnt;
-		v2_ext->hdr.flag.release = SMC_RELEASE;
-		v2_ext->hdr.flag.seid = 1;
 		v2_ext->hdr.smcd_v2_ext_offset = htons(sizeof(*v2_ext) -
 				offsetofend(struct smc_clnt_opts_area_hdr,
 					    smcd_v2_ext_offset) +
 				v2_ext->hdr.eid_cnt * SMC_MAX_EID_LEN);
-		if (ini->ism_dev[0])
-			smc_ism_get_system_eid(ini->ism_dev[0], &eid);
-		else
-			smc_ism_get_system_eid(ini->ism_dev[1], &eid);
-		if (eid)
+		smc_ism_get_system_eid(&eid);
+		if (eid && v2_ext->hdr.flag.seid)
 			memcpy(smcd_v2_ext->system_eid, eid, SMC_MAX_EID_LEN);
-		plen += sizeof(*v2_ext) + sizeof(*smcd_v2_ext);
+		plen += sizeof(*smcd_v2_ext);
 		if (ini->ism_offered_cnt) {
 			for (i = 1; i <= ini->ism_offered_cnt; i++) {
 				gidchids[i - 1].gid =
@@ -587,6 +930,9 @@
 				sizeof(struct smc_clc_smcd_gid_chid);
 		}
 	}
+	if (smcr_indicated(ini->smc_type_v2))
+		memcpy(v2_ext->roce, ini->smcrv2.ib_gid_v2, SMC_GID_SIZE);
+
 	pclc_base->hdr.length = htons(plen);
 	memcpy(trl->eyecatcher, SMC_EYECATCHER, sizeof(SMC_EYECATCHER));
 
@@ -608,13 +954,16 @@
 	}
 	if (ini->smc_type_v2 != SMC_TYPE_N) {
 		vec[i].iov_base = v2_ext;
-		vec[i++].iov_len = sizeof(*v2_ext);
-		vec[i].iov_base = smcd_v2_ext;
-		vec[i++].iov_len = sizeof(*smcd_v2_ext);
-		if (ini->ism_offered_cnt) {
-			vec[i].iov_base = gidchids;
-			vec[i++].iov_len = ini->ism_offered_cnt *
+		vec[i++].iov_len = sizeof(*v2_ext) +
+				   (v2_ext->hdr.eid_cnt * SMC_MAX_EID_LEN);
+		if (smcd_indicated(ini->smc_type_v2)) {
+			vec[i].iov_base = smcd_v2_ext;
+			vec[i++].iov_len = sizeof(*smcd_v2_ext);
+			if (ini->ism_offered_cnt) {
+				vec[i].iov_base = gidchids;
+				vec[i++].iov_len = ini->ism_offered_cnt *
 					sizeof(struct smc_clc_smcd_gid_chid);
+			}
 		}
 	}
 	vec[i].iov_base = trl;
@@ -636,13 +985,15 @@
 /* build and send CLC CONFIRM / ACCEPT message */
 static int smc_clc_send_confirm_accept(struct smc_sock *smc,
 				       struct smc_clc_msg_accept_confirm_v2 *clc_v2,
-				       int first_contact, u8 version)
+				       int first_contact, u8 version,
+				       u8 *eid, struct smc_init_info *ini)
 {
 	struct smc_connection *conn = &smc->conn;
 	struct smc_clc_msg_accept_confirm *clc;
 	struct smc_clc_first_contact_ext fce;
+	struct smc_clc_fce_gid_ext gle;
 	struct smc_clc_msg_trail trl;
-	struct kvec vec[3];
+	struct kvec vec[5];
 	struct msghdr msg;
 	int i, len;
 
@@ -664,12 +1015,10 @@
 		if (version == SMC_V1) {
 			clc->hdr.length = htons(SMCD_CLC_ACCEPT_CONFIRM_LEN);
 		} else {
-			u8 *eid = NULL;
-
-			clc_v2->chid = htons(smc_ism_get_chid(conn->lgr->smcd));
-			smc_ism_get_system_eid(conn->lgr->smcd, &eid);
-			if (eid)
-				memcpy(clc_v2->eid, eid, SMC_MAX_EID_LEN);
+			clc_v2->d1.chid =
+				htons(smc_ism_get_chid(conn->lgr->smcd));
+			if (eid && eid[0])
+				memcpy(clc_v2->d1.eid, eid, SMC_MAX_EID_LEN);
 			len = SMCD_CLC_ACCEPT_CONFIRM_LEN_V2;
 			if (first_contact)
 				smc_clc_fill_fce(&fce, &len);
@@ -708,6 +1057,26 @@
 		clc->r0.rmb_dma_addr = cpu_to_be64((u64)sg_dma_address
 				(conn->rmb_desc->sgt[link->link_idx].sgl));
 		hton24(clc->r0.psn, link->psn_initial);
+		if (version == SMC_V1) {
+			clc->hdr.length = htons(SMCR_CLC_ACCEPT_CONFIRM_LEN);
+		} else {
+			if (eid && eid[0])
+				memcpy(clc_v2->r1.eid, eid, SMC_MAX_EID_LEN);
+			len = SMCR_CLC_ACCEPT_CONFIRM_LEN_V2;
+			if (first_contact) {
+				smc_clc_fill_fce(&fce, &len);
+				fce.v2_direct = !link->lgr->uses_gateway;
+				memset(&gle, 0, sizeof(gle));
+				if (ini && clc->hdr.type == SMC_CLC_CONFIRM) {
+					gle.gid_cnt = ini->smcrv2.gidlist.len;
+					len += sizeof(gle);
+					len += gle.gid_cnt * sizeof(gle.gid[0]);
+				} else {
+					len += sizeof(gle.reserved);
+				}
+			}
+			clc_v2->hdr.length = htons(len);
+		}
 		memcpy(trl.eyecatcher, SMC_EYECATCHER, sizeof(SMC_EYECATCHER));
 	}
 
@@ -715,7 +1084,10 @@
 	i = 0;
 	vec[i].iov_base = clc_v2;
 	if (version > SMC_V1)
-		vec[i++].iov_len = SMCD_CLC_ACCEPT_CONFIRM_LEN_V2 - sizeof(trl);
+		vec[i++].iov_len = (clc->hdr.typev1 == SMC_TYPE_D ?
+					SMCD_CLC_ACCEPT_CONFIRM_LEN_V2 :
+					SMCR_CLC_ACCEPT_CONFIRM_LEN_V2) -
+				   sizeof(trl);
 	else
 		vec[i++].iov_len = (clc->hdr.typev1 == SMC_TYPE_D ?
 						SMCD_CLC_ACCEPT_CONFIRM_LEN :
@@ -724,6 +1096,18 @@
 	if (version > SMC_V1 && first_contact) {
 		vec[i].iov_base = &fce;
 		vec[i++].iov_len = sizeof(fce);
+		if (!conn->lgr->is_smcd) {
+			if (clc->hdr.type == SMC_CLC_CONFIRM) {
+				vec[i].iov_base = &gle;
+				vec[i++].iov_len = sizeof(gle);
+				vec[i].iov_base = &ini->smcrv2.gidlist.list;
+				vec[i++].iov_len = gle.gid_cnt *
+						   sizeof(gle.gid[0]);
+			} else {
+				vec[i].iov_base = &gle.reserved;
+				vec[i++].iov_len = sizeof(gle.reserved);
+			}
+		}
 	}
 	vec[i].iov_base = &trl;
 	vec[i++].iov_len = sizeof(trl);
@@ -733,7 +1117,7 @@
 
 /* send CLC CONFIRM message across internal TCP socket */
 int smc_clc_send_confirm(struct smc_sock *smc, bool clnt_first_contact,
-			 u8 version)
+			 u8 version, u8 *eid, struct smc_init_info *ini)
 {
 	struct smc_clc_msg_accept_confirm_v2 cclc_v2;
 	int reason_code = 0;
@@ -743,7 +1127,7 @@
 	memset(&cclc_v2, 0, sizeof(cclc_v2));
 	cclc_v2.hdr.type = SMC_CLC_CONFIRM;
 	len = smc_clc_send_confirm_accept(smc, &cclc_v2, clnt_first_contact,
-					  version);
+					  version, eid, ini);
 	if (len < ntohs(cclc_v2.hdr.length)) {
 		if (len >= 0) {
 			reason_code = -ENETUNREACH;
@@ -758,7 +1142,7 @@
 
 /* send CLC ACCEPT message across internal TCP socket */
 int smc_clc_send_accept(struct smc_sock *new_smc, bool srv_first_contact,
-			u8 version)
+			u8 version, u8 *negotiated_eid)
 {
 	struct smc_clc_msg_accept_confirm_v2 aclc_v2;
 	int len;
@@ -766,7 +1150,7 @@
 	memset(&aclc_v2, 0, sizeof(aclc_v2));
 	aclc_v2.hdr.type = SMC_CLC_ACCEPT;
 	len = smc_clc_send_confirm_accept(new_smc, &aclc_v2, srv_first_contact,
-					  version);
+					  version, negotiated_eid, NULL);
 	if (len < ntohs(aclc_v2.hdr.length))
 		len = len >= 0 ? -EPROTO : -new_smc->clcsock->sk->sk_err;
 
@@ -786,4 +1170,14 @@
 	u = utsname();
 	memcpy(smc_hostname, u->nodename,
 	       min_t(size_t, strlen(u->nodename), sizeof(smc_hostname)));
+
+	INIT_LIST_HEAD(&smc_clc_eid_table.list);
+	rwlock_init(&smc_clc_eid_table.lock);
+	smc_clc_eid_table.ueid_cnt = 0;
+	smc_clc_eid_table.seid_enabled = 1;
+}
+
+void smc_clc_exit(void)
+{
+	smc_clc_ueid_remove(NULL);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_clc.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_clc.h
@@ -14,8 +14,10 @@
 #define _SMC_CLC_H
 
 #include <rdma/ib_verbs.h>
+#include <linux/smc.h>
 
 #include "smc.h"
+#include "smc_netlink.h"
 
 #define SMC_CLC_PROPOSAL	0x01
 #define SMC_CLC_ACCEPT		0x02
@@ -42,6 +44,7 @@
 #define SMC_CLC_DECL_NOV2DEXT	0x03030005  /* peer sent no clc SMC-Dv2 ext.  */
 #define SMC_CLC_DECL_NOSEID	0x03030006  /* peer sent no SEID	      */
 #define SMC_CLC_DECL_NOSMCD2DEV	0x03030007  /* no SMC-Dv2 device found	      */
+#define SMC_CLC_DECL_NOUEID	0x03030008  /* peer sent no UEID	      */
 #define SMC_CLC_DECL_MODEUNSUPP	0x03040000  /* smc modes do not match (R or D)*/
 #define SMC_CLC_DECL_RMBE_EC	0x03050000  /* peer has eyecatcher in RMBE    */
 #define SMC_CLC_DECL_OPTUNSUPP	0x03060000  /* fastopen sockopt not supported */
@@ -52,6 +55,8 @@
 #define SMC_CLC_DECL_NOSRVLINK	0x030b0000  /* SMC-R link from srv not found  */
 #define SMC_CLC_DECL_VERSMISMAT	0x030c0000  /* SMC version mismatch	      */
 #define SMC_CLC_DECL_MAX_DMB	0x030d0000  /* SMC-D DMB limit exceeded       */
+#define SMC_CLC_DECL_NOROUTE	0x030e0000  /* SMC-Rv2 conn. no route to peer */
+#define SMC_CLC_DECL_NOINDIRECT	0x030f0000  /* SMC-Rv2 conn. indirect mismatch*/
 #define SMC_CLC_DECL_SYNCERR	0x04000000  /* synchronization error          */
 #define SMC_CLC_DECL_PEERDECL	0x05000000  /* peer declined during handshake */
 #define SMC_CLC_DECL_INTERR	0x09990000  /* internal error		      */
@@ -158,6 +163,7 @@
 } __aligned(4);
 
 #define SMC_CLC_MAX_V6_PREFIX		8
+#define SMC_CLC_MAX_UEID		8
 
 struct smc_clc_msg_proposal_area {
 	struct smc_clc_msg_proposal		pclc_base;
@@ -165,6 +171,7 @@
 	struct smc_clc_msg_proposal_prefix	pclc_prfx;
 	struct smc_clc_ipv6_prefix	pclc_prfx_ipv6[SMC_CLC_MAX_V6_PREFIX];
 	struct smc_clc_v2_extension		pclc_v2_ext;
+	u8			user_eids[SMC_CLC_MAX_UEID][SMC_MAX_EID_LEN];
 	struct smc_clc_smcd_v2_extension	pclc_smcd_v2_ext;
 	struct smc_clc_smcd_gid_chid		pclc_gidchids[SMC_MAX_ISM_DEVS];
 	struct smc_clc_msg_trail		pclc_trl;
@@ -209,11 +216,14 @@
 #define SMC_CLC_OS_AIX		3
 
 struct smc_clc_first_contact_ext {
-	u8 reserved1;
 #if defined(__BIG_ENDIAN_BITFIELD)
+	u8 v2_direct : 1,
+	   reserved  : 7;
 	u8 os_type : 4,
 	   release : 4;
 #elif defined(__LITTLE_ENDIAN_BITFIELD)
+	u8 reserved  : 7,
+	   v2_direct : 1;
 	u8 release : 4,
 	   os_type : 4;
 #endif
@@ -221,6 +231,13 @@
 	u8 hostname[SMC_MAX_HOSTNAME_LEN];
 };
 
+struct smc_clc_fce_gid_ext {
+	u8 reserved[16];
+	u8 gid_cnt;
+	u8 reserved2[3];
+	u8 gid[][SMC_GID_SIZE];
+};
+
 struct smc_clc_msg_accept_confirm {	/* clc accept / confirm message */
 	struct smc_clc_msg_hdr hdr;
 	union {
@@ -235,13 +252,17 @@
 struct smc_clc_msg_accept_confirm_v2 {	/* clc accept / confirm message */
 	struct smc_clc_msg_hdr hdr;
 	union {
-		struct smcr_clc_msg_accept_confirm r0; /* SMC-R */
+		struct { /* SMC-R */
+			struct smcr_clc_msg_accept_confirm r0;
+			u8 eid[SMC_MAX_EID_LEN];
+			u8 reserved6[8];
+		} r1;
 		struct { /* SMC-D */
 			struct smcd_clc_msg_accept_confirm_common d0;
 			__be16 chid;
 			u8 eid[SMC_MAX_EID_LEN];
 			u8 reserved5[8];
-		};
+		} d1;
 	};
 };
 
@@ -260,12 +281,34 @@
 	struct smc_clc_msg_trail trl; /* eye catcher "SMCD" or "SMCR" EBCDIC */
 } __aligned(4);
 
+#define SMC_DECL_DIAG_COUNT_V2	4 /* no. of additional peer diagnosis codes */
+
+struct smc_clc_msg_decline_v2 {	/* clc decline message */
+	struct smc_clc_msg_hdr hdr;
+	u8 id_for_peer[SMC_SYSTEMID_LEN]; /* sender peer_id */
+	__be32 peer_diagnosis;	/* diagnosis information */
+#if defined(__BIG_ENDIAN_BITFIELD)
+	u8 os_type  : 4,
+	   reserved : 4;
+#elif defined(__LITTLE_ENDIAN_BITFIELD)
+	u8 reserved : 4,
+	   os_type  : 4;
+#endif
+	u8 reserved2[3];
+	__be32 peer_diagnosis_v2[SMC_DECL_DIAG_COUNT_V2];
+	struct smc_clc_msg_trail trl; /* eye catcher "SMCD" or "SMCR" EBCDIC */
+} __aligned(4);
+
 /* determine start of the prefix area within the proposal message */
 static inline struct smc_clc_msg_proposal_prefix *
 smc_clc_proposal_get_prefix(struct smc_clc_msg_proposal *pclc)
 {
+	u16 offset = ntohs(pclc->iparea_offset);
+
+	if (offset > sizeof(struct smc_clc_msg_smcd))
+		return NULL;
 	return (struct smc_clc_msg_proposal_prefix *)
-	       ((u8 *)pclc + sizeof(*pclc) + ntohs(pclc->iparea_offset));
+	       ((u8 *)pclc + sizeof(*pclc) + offset);
 }
 
 static inline bool smcr_indicated(int smc_type)
@@ -278,6 +321,17 @@
 	return smc_type == SMC_TYPE_D || smc_type == SMC_TYPE_B;
 }
 
+static inline u8 smc_indicated_type(int is_smcd, int is_smcr)
+{
+	if (is_smcd && is_smcr)
+		return SMC_TYPE_B;
+	if (is_smcd)
+		return SMC_TYPE_D;
+	if (is_smcr)
+		return SMC_TYPE_R;
+	return SMC_TYPE_N;
+}
+
 /* get SMC-D info from proposal message */
 static inline struct smc_clc_msg_smcd *
 smc_get_clc_msg_smcd(struct smc_clc_msg_proposal *prop)
@@ -307,9 +361,15 @@
 static inline struct smc_clc_smcd_v2_extension *
 smc_get_clc_smcd_v2_ext(struct smc_clc_v2_extension *prop_v2ext)
 {
+	u16 max_offset = offsetof(struct smc_clc_msg_proposal_area, pclc_smcd_v2_ext) -
+		offsetof(struct smc_clc_msg_proposal_area, pclc_v2_ext) -
+		offsetof(struct smc_clc_v2_extension, hdr) -
+		offsetofend(struct smc_clnt_opts_area_hdr, smcd_v2_ext_offset);
+
 	if (!prop_v2ext)
 		return NULL;
-	if (!ntohs(prop_v2ext->hdr.smcd_v2_ext_offset))
+	if (!ntohs(prop_v2ext->hdr.smcd_v2_ext_offset) ||
+	    ntohs(prop_v2ext->hdr.smcd_v2_ext_offset) > max_offset)
 		return NULL;
 
 	return (struct smc_clc_smcd_v2_extension *)
@@ -330,10 +390,22 @@
 int smc_clc_send_decline(struct smc_sock *smc, u32 peer_diag_info, u8 version);
 int smc_clc_send_proposal(struct smc_sock *smc, struct smc_init_info *ini);
 int smc_clc_send_confirm(struct smc_sock *smc, bool clnt_first_contact,
-			 u8 version);
+			 u8 version, u8 *eid, struct smc_init_info *ini);
 int smc_clc_send_accept(struct smc_sock *smc, bool srv_first_contact,
-			u8 version);
+			u8 version, u8 *negotiated_eid);
 void smc_clc_init(void) __init;
+void smc_clc_exit(void);
 void smc_clc_get_hostname(u8 **host);
+bool smc_clc_match_eid(u8 *negotiated_eid,
+		       struct smc_clc_v2_extension *smc_v2_ext,
+		       u8 *peer_eid, u8 *local_eid);
+int smc_clc_ueid_count(void);
+int smc_nl_dump_ueid(struct sk_buff *skb, struct netlink_callback *cb);
+int smc_nl_add_ueid(struct sk_buff *skb, struct genl_info *info);
+int smc_nl_remove_ueid(struct sk_buff *skb, struct genl_info *info);
+int smc_nl_flush_ueid(struct sk_buff *skb, struct genl_info *info);
+int smc_nl_dump_seid(struct sk_buff *skb, struct netlink_callback *cb);
+int smc_nl_enable_seid(struct sk_buff *skb, struct genl_info *info);
+int smc_nl_disable_seid(struct sk_buff *skb, struct genl_info *info);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_close.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_close.c
@@ -64,8 +64,8 @@
 
 		rc = sk_wait_event(sk, &timeout,
 				   !smc_tx_prepared_sends(&smc->conn) ||
-				   sk->sk_err == ECONNABORTED ||
-				   sk->sk_err == ECONNRESET ||
+				   READ_ONCE(sk->sk_err) == ECONNABORTED ||
+				   READ_ONCE(sk->sk_err) == ECONNRESET ||
 				   smc->conn.killed,
 				   &wait);
 		if (rc)
@@ -113,7 +113,8 @@
 	struct sock *sk = &smc->sk;
 
 	release_sock(sk);
-	cancel_work_sync(&smc->conn.close_work);
+	if (cancel_work_sync(&smc->conn.close_work))
+		sock_put(sk);
 	cancel_delayed_work_sync(&smc->conn.tx_work);
 	lock_sock(sk);
 }
@@ -170,7 +171,7 @@
 		break;
 	}
 
-	sock_set_flag(sk, SOCK_DEAD);
+	smc_sock_set_flag(sk, SOCK_DEAD);
 	sk->sk_state_change(sk);
 
 	if (release_clcsock) {
@@ -195,6 +196,7 @@
 	int old_state;
 	long timeout;
 	int rc = 0;
+	int rc1 = 0;
 
 	timeout = current->flags & PF_EXITING ?
 		  0 : sock_flag(sk, SOCK_LINGER) ?
@@ -228,6 +230,15 @@
 			/* send close request */
 			rc = smc_close_final(conn);
 			sk->sk_state = SMC_PEERCLOSEWAIT1;
+
+			/* actively shutdown clcsock before peer close it,
+			 * prevent peer from entering TIME_WAIT state.
+			 */
+			if (smc->clcsock && smc->clcsock->sk) {
+				rc1 = kernel_sock_shutdown(smc->clcsock,
+							   SHUT_RDWR);
+				rc = rc ? rc : rc1;
+			}
 		} else {
 			/* peer event has changed the state */
 			goto again;
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_core.c
@@ -170,8 +170,10 @@
 
 	if (!conn->lgr->is_smcd) {
 		rc = smcr_lgr_conn_assign_link(conn, first);
-		if (rc)
+		if (rc) {
+			conn->lgr = NULL;
 			return rc;
+		}
 	}
 	/* find a new alert_token_local value not yet used by some connection
 	 * in this link group
@@ -223,7 +225,6 @@
 	struct smc_nl_dmp_ctx *cb_ctx = smc_nl_dmp_ctx(cb);
 	char hostname[SMC_MAX_HOSTNAME_LEN + 1];
 	char smc_seid[SMC_MAX_EID_LEN + 1];
-	struct smcd_dev *smcd_dev;
 	struct nlattr *attrs;
 	u8 *seid = NULL;
 	u8 *host = NULL;
@@ -245,6 +246,8 @@
 		goto errattr;
 	if (nla_put_u8(skb, SMC_NLA_SYS_IS_ISM_V2, smc_ism_is_v2_capable()))
 		goto errattr;
+	if (nla_put_u8(skb, SMC_NLA_SYS_IS_SMCR_V2, true))
+		goto errattr;
 	smc_clc_get_hostname(&host);
 	if (host) {
 		memcpy(hostname, host, SMC_MAX_HOSTNAME_LEN);
@@ -252,13 +255,8 @@
 		if (nla_put_string(skb, SMC_NLA_SYS_LOCAL_HOST, hostname))
 			goto errattr;
 	}
-	mutex_lock(&smcd_dev_list.mutex);
-	smcd_dev = list_first_entry_or_null(&smcd_dev_list.list,
-					    struct smcd_dev, list);
-	if (smcd_dev)
-		smc_ism_get_system_eid(smcd_dev, &seid);
-	mutex_unlock(&smcd_dev_list.mutex);
-	if (seid && smc_ism_is_v2_capable()) {
+	if (smc_ism_is_v2_capable()) {
+		smc_ism_get_system_eid(&seid);
 		memcpy(smc_seid, seid, SMC_MAX_EID_LEN);
 		smc_seid[SMC_MAX_EID_LEN] = 0;
 		if (nla_put_string(skb, SMC_NLA_SYS_SEID, smc_seid))
@@ -277,12 +275,65 @@
 	return skb->len;
 }
 
+/* Fill SMC_NLA_LGR_D_V2_COMMON/SMC_NLA_LGR_R_V2_COMMON nested attributes */
+static int smc_nl_fill_lgr_v2_common(struct smc_link_group *lgr,
+				     struct sk_buff *skb,
+				     struct netlink_callback *cb,
+				     struct nlattr *v2_attrs)
+{
+	char smc_host[SMC_MAX_HOSTNAME_LEN + 1];
+	char smc_eid[SMC_MAX_EID_LEN + 1];
+
+	if (nla_put_u8(skb, SMC_NLA_LGR_V2_VER, lgr->smc_version))
+		goto errv2attr;
+	if (nla_put_u8(skb, SMC_NLA_LGR_V2_REL, lgr->peer_smc_release))
+		goto errv2attr;
+	if (nla_put_u8(skb, SMC_NLA_LGR_V2_OS, lgr->peer_os))
+		goto errv2attr;
+	memcpy(smc_host, lgr->peer_hostname, SMC_MAX_HOSTNAME_LEN);
+	smc_host[SMC_MAX_HOSTNAME_LEN] = 0;
+	if (nla_put_string(skb, SMC_NLA_LGR_V2_PEER_HOST, smc_host))
+		goto errv2attr;
+	memcpy(smc_eid, lgr->negotiated_eid, SMC_MAX_EID_LEN);
+	smc_eid[SMC_MAX_EID_LEN] = 0;
+	if (nla_put_string(skb, SMC_NLA_LGR_V2_NEG_EID, smc_eid))
+		goto errv2attr;
+
+	nla_nest_end(skb, v2_attrs);
+	return 0;
+
+errv2attr:
+	nla_nest_cancel(skb, v2_attrs);
+	return -EMSGSIZE;
+}
+
+static int smc_nl_fill_smcr_lgr_v2(struct smc_link_group *lgr,
+				   struct sk_buff *skb,
+				   struct netlink_callback *cb)
+{
+	struct nlattr *v2_attrs;
+
+	v2_attrs = nla_nest_start(skb, SMC_NLA_LGR_R_V2);
+	if (!v2_attrs)
+		goto errattr;
+	if (nla_put_u8(skb, SMC_NLA_LGR_R_V2_DIRECT, !lgr->uses_gateway))
+		goto errv2attr;
+
+	nla_nest_end(skb, v2_attrs);
+	return 0;
+
+errv2attr:
+	nla_nest_cancel(skb, v2_attrs);
+errattr:
+	return -EMSGSIZE;
+}
+
 static int smc_nl_fill_lgr(struct smc_link_group *lgr,
 			   struct sk_buff *skb,
 			   struct netlink_callback *cb)
 {
 	char smc_target[SMC_MAX_PNETID_LEN + 1];
-	struct nlattr *attrs;
+	struct nlattr *attrs, *v2_attrs;
 
 	attrs = nla_nest_start(skb, SMC_GEN_LGR_SMCR);
 	if (!attrs)
@@ -302,6 +353,15 @@
 	smc_target[SMC_MAX_PNETID_LEN] = 0;
 	if (nla_put_string(skb, SMC_NLA_LGR_R_PNETID, smc_target))
 		goto errattr;
+	if (lgr->smc_version > SMC_V1) {
+		v2_attrs = nla_nest_start(skb, SMC_NLA_LGR_R_V2_COMMON);
+		if (!v2_attrs)
+			goto errattr;
+		if (smc_nl_fill_lgr_v2_common(lgr, skb, cb, v2_attrs))
+			goto errattr;
+		if (smc_nl_fill_smcr_lgr_v2(lgr, skb, cb))
+			goto errattr;
+	}
 
 	nla_nest_end(skb, attrs);
 	return 0;
@@ -434,10 +494,7 @@
 				struct sk_buff *skb,
 				struct netlink_callback *cb)
 {
-	char smc_host[SMC_MAX_HOSTNAME_LEN + 1];
 	char smc_pnet[SMC_MAX_PNETID_LEN + 1];
-	char smc_eid[SMC_MAX_EID_LEN + 1];
-	struct nlattr *v2_attrs;
 	struct nlattr *attrs;
 	void *nlh;
 
@@ -469,32 +526,19 @@
 	smc_pnet[SMC_MAX_PNETID_LEN] = 0;
 	if (nla_put_string(skb, SMC_NLA_LGR_D_PNETID, smc_pnet))
 		goto errattr;
+	if (lgr->smc_version > SMC_V1) {
+		struct nlattr *v2_attrs;
 
-	v2_attrs = nla_nest_start(skb, SMC_NLA_LGR_V2);
-	if (!v2_attrs)
-		goto errattr;
-	if (nla_put_u8(skb, SMC_NLA_LGR_V2_VER, lgr->smc_version))
-		goto errv2attr;
-	if (nla_put_u8(skb, SMC_NLA_LGR_V2_REL, lgr->peer_smc_release))
-		goto errv2attr;
-	if (nla_put_u8(skb, SMC_NLA_LGR_V2_OS, lgr->peer_os))
-		goto errv2attr;
-	memcpy(smc_host, lgr->peer_hostname, SMC_MAX_HOSTNAME_LEN);
-	smc_host[SMC_MAX_HOSTNAME_LEN] = 0;
-	if (nla_put_string(skb, SMC_NLA_LGR_V2_PEER_HOST, smc_host))
-		goto errv2attr;
-	memcpy(smc_eid, lgr->negotiated_eid, SMC_MAX_EID_LEN);
-	smc_eid[SMC_MAX_EID_LEN] = 0;
-	if (nla_put_string(skb, SMC_NLA_LGR_V2_NEG_EID, smc_eid))
-		goto errv2attr;
-
-	nla_nest_end(skb, v2_attrs);
+		v2_attrs = nla_nest_start(skb, SMC_NLA_LGR_D_V2_COMMON);
+		if (!v2_attrs)
+			goto errattr;
+		if (smc_nl_fill_lgr_v2_common(lgr, skb, cb, v2_attrs))
+			goto errattr;
+	}
 	nla_nest_end(skb, attrs);
 	genlmsg_end(skb, nlh);
 	return 0;
 
-errv2attr:
-	nla_nest_cancel(skb, v2_attrs);
 errattr:
 	nla_nest_cancel(skb, attrs);
 errout:
@@ -579,21 +623,18 @@
 	return skb->len;
 }
 
-void smc_lgr_cleanup_early(struct smc_connection *conn)
+void smc_lgr_cleanup_early(struct smc_link_group *lgr)
 {
-	struct smc_link_group *lgr = conn->lgr;
-	struct list_head *lgr_list;
 	spinlock_t *lgr_lock;
 
 	if (!lgr)
 		return;
 
-	smc_conn_free(conn);
-	lgr_list = smc_lgr_list_head(lgr, &lgr_lock);
+	smc_lgr_list_head(lgr, &lgr_lock);
 	spin_lock_bh(lgr_lock);
 	/* do not use this link group for new connections */
-	if (!list_empty(lgr_list))
-		list_del_init(lgr_list);
+	if (!list_empty(&lgr->list))
+		list_del_init(&lgr->list);
 	spin_unlock_bh(lgr_lock);
 	__smc_lgr_terminate(lgr, true);
 }
@@ -605,7 +646,7 @@
 	for (i = 0; i < SMC_LINKS_PER_LGR_MAX; i++) {
 		struct smc_link *lnk = &lgr->lnk[i];
 
-		if (smc_link_usable(lnk))
+		if (smc_link_sendable(lnk))
 			lnk->state = SMC_LNK_INACTIVE;
 	}
 	wake_up_all(&lgr->llc_msg_waiter);
@@ -665,13 +706,14 @@
 	int i;
 
 	while (1) {
+again:
 		link_id = ++lgr->next_link_id;
 		if (!link_id)	/* skip zero as link_id */
 			link_id = ++lgr->next_link_id;
 		for (i = 0; i < SMC_LINKS_PER_LGR_MAX; i++) {
 			if (smc_link_usable(&lgr->lnk[i]) &&
 			    lgr->lnk[i].link_id == link_id)
-				continue;
+				goto again;
 		}
 		break;
 	}
@@ -690,24 +732,30 @@
 int smcr_link_init(struct smc_link_group *lgr, struct smc_link *lnk,
 		   u8 link_idx, struct smc_init_info *ini)
 {
+	struct smc_ib_device *smcibdev;
 	u8 rndvec[3];
 	int rc;
 
-	get_device(&ini->ib_dev->ibdev->dev);
-	atomic_inc(&ini->ib_dev->lnk_cnt);
+	if (lgr->smc_version == SMC_V2) {
+		lnk->smcibdev = ini->smcrv2.ib_dev_v2;
+		lnk->ibport = ini->smcrv2.ib_port_v2;
+	} else {
+		lnk->smcibdev = ini->ib_dev;
+		lnk->ibport = ini->ib_port;
+	}
+	get_device(&lnk->smcibdev->ibdev->dev);
+	atomic_inc(&lnk->smcibdev->lnk_cnt);
+	lnk->path_mtu = lnk->smcibdev->pattr[lnk->ibport - 1].active_mtu;
 	lnk->link_id = smcr_next_link_id(lgr);
 	lnk->lgr = lgr;
 	lnk->link_idx = link_idx;
-	lnk->smcibdev = ini->ib_dev;
-	lnk->ibport = ini->ib_port;
 	smc_ibdev_cnt_inc(lnk);
 	smcr_copy_dev_info_to_link(lnk);
-	lnk->path_mtu = ini->ib_dev->pattr[ini->ib_port - 1].active_mtu;
 	atomic_set(&lnk->conn_cnt, 0);
 	smc_llc_link_set_uid(lnk);
 	INIT_WORK(&lnk->link_down_wrk, smc_link_down_work);
-	if (!ini->ib_dev->initialized) {
-		rc = (int)smc_ib_setup_per_ibdev(ini->ib_dev);
+	if (!lnk->smcibdev->initialized) {
+		rc = (int)smc_ib_setup_per_ibdev(lnk->smcibdev);
 		if (rc)
 			goto out;
 	}
@@ -715,7 +763,9 @@
 	lnk->psn_initial = rndvec[0] + (rndvec[1] << 8) +
 		(rndvec[2] << 16);
 	rc = smc_ib_determine_gid(lnk->smcibdev, lnk->ibport,
-				  ini->vlan_id, lnk->gid, &lnk->sgid_index);
+				  ini->vlan_id, lnk->gid, &lnk->sgid_index,
+				  lgr->smc_version == SMC_V2 ?
+						  &ini->smcrv2 : NULL);
 	if (rc)
 		goto out;
 	rc = smc_llc_link_init(lnk);
@@ -746,11 +796,12 @@
 	smc_llc_link_clear(lnk, false);
 out:
 	smc_ibdev_cnt_dec(lnk);
-	put_device(&ini->ib_dev->ibdev->dev);
+	put_device(&lnk->smcibdev->ibdev->dev);
+	smcibdev = lnk->smcibdev;
 	memset(lnk, 0, sizeof(struct smc_link));
 	lnk->state = SMC_LNK_UNUSED;
-	if (!atomic_dec_return(&ini->ib_dev->lnk_cnt))
-		wake_up(&ini->ib_dev->lnks_deleted);
+	if (!atomic_dec_return(&smcibdev->lnk_cnt))
+		wake_up(&smcibdev->lnks_deleted);
 	return rc;
 }
 
@@ -814,18 +865,37 @@
 		atomic_inc(&ini->ism_dev[ini->ism_selected]->lgr_cnt);
 	} else {
 		/* SMC-R specific settings */
+		struct smc_ib_device *ibdev;
+		int ibport;
+
 		lgr->role = smc->listen_smc ? SMC_SERV : SMC_CLNT;
-		memcpy(lgr->peer_systemid, ini->ib_lcl->id_for_peer,
+		lgr->smc_version = ini->smcr_version;
+		memcpy(lgr->peer_systemid, ini->peer_systemid,
 		       SMC_SYSTEMID_LEN);
-		memcpy(lgr->pnet_id, ini->ib_dev->pnetid[ini->ib_port - 1],
+		if (lgr->smc_version == SMC_V2) {
+			ibdev = ini->smcrv2.ib_dev_v2;
+			ibport = ini->smcrv2.ib_port_v2;
+			lgr->saddr = ini->smcrv2.saddr;
+			lgr->uses_gateway = ini->smcrv2.uses_gateway;
+			memcpy(lgr->nexthop_mac, ini->smcrv2.nexthop_mac,
+			       ETH_ALEN);
+		} else {
+			ibdev = ini->ib_dev;
+			ibport = ini->ib_port;
+		}
+		memcpy(lgr->pnet_id, ibdev->pnetid[ibport - 1],
 		       SMC_MAX_PNETID_LEN);
+		if (smc_wr_alloc_lgr_mem(lgr))
+			goto free_wq;
 		smc_llc_lgr_init(lgr, smc);
 
 		link_idx = SMC_SINGLE_LINK;
 		lnk = &lgr->lnk[link_idx];
 		rc = smcr_link_init(lgr, lnk, link_idx, ini);
-		if (rc)
+		if (rc) {
+			smc_wr_free_lgr_mem(lgr);
 			goto free_wq;
+		}
 		lgr_list = &smc_lgr_list.list;
 		lgr_lock = &smc_lgr_list.lock;
 		atomic_inc(&lgr_cnt);
@@ -1056,13 +1126,13 @@
 			smc_ism_unset_conn(conn);
 		tasklet_kill(&conn->rx_tsklet);
 	} else {
-		smc_cdc_tx_dismiss_slots(conn);
+		smc_cdc_wait_pend_tx_wr(conn);
 		if (current_work() != &conn->abort_work)
 			cancel_work_sync(&conn->abort_work);
 	}
 	if (!list_empty(&lgr->list)) {
-		smc_lgr_unregister_conn(conn);
 		smc_buf_unuse(conn, lgr); /* allow buffer reuse */
+		smc_lgr_unregister_conn(conn);
 	}
 
 	if (!lgr->conns_num)
@@ -1133,7 +1203,7 @@
 	smc_llc_link_clear(lnk, log);
 	smcr_buf_unmap_lgr(lnk);
 	smcr_rtoken_clear_link(lnk);
-	smc_ib_modify_qp_reset(lnk);
+	smc_ib_modify_qp_error(lnk);
 	smc_wr_free_link(lnk);
 	smc_ib_destroy_queue_pair(lnk);
 	smc_ib_dealloc_protection_domain(lnk);
@@ -1232,6 +1302,7 @@
 		if (!atomic_dec_return(&lgr->smcd->lgr_cnt))
 			wake_up(&lgr->smcd->lgrs_deleted);
 	} else {
+		smc_wr_free_lgr_mem(lgr);
 		if (!atomic_dec_return(&lgr_cnt))
 			wake_up(&lgrs_deleted);
 	}
@@ -1264,7 +1335,7 @@
 		else
 			tasklet_unlock_wait(&conn->rx_tsklet);
 	} else {
-		smc_cdc_tx_dismiss_slots(conn);
+		smc_cdc_wait_pend_tx_wr(conn);
 	}
 	smc_lgr_unregister_conn(conn);
 	smc_close_active_abort(smc);
@@ -1297,7 +1368,7 @@
 	if (lgr->terminating)
 		return;	/* lgr already terminating */
 	/* cancel free_work sync, will terminate when lgr->freeing is set */
-	cancel_delayed_work_sync(&lgr->free_work);
+	cancel_delayed_work(&lgr->free_work);
 	lgr->terminating = 1;
 
 	/* kill remaining link group connections */
@@ -1486,6 +1557,7 @@
 {
 	struct smc_link_group *lgr, *n;
 
+	spin_lock_bh(&smc_lgr_list.lock);
 	list_for_each_entry_safe(lgr, n, &smc_lgr_list.list, list) {
 		struct smc_link *link;
 
@@ -1500,6 +1572,7 @@
 		if (link)
 			smc_llc_add_link_local(link);
 	}
+	spin_unlock_bh(&smc_lgr_list.lock);
 }
 
 /* link is down - switch connections to alternate link,
@@ -1514,7 +1587,6 @@
 	if (!lgr || lnk->state == SMC_LNK_UNUSED || list_empty(&lgr->list))
 		return;
 
-	smc_ib_modify_qp_reset(lnk);
 	to_lnk = smc_switch_conns(lgr, lnk, true);
 	if (!to_lnk) { /* no backup link available */
 		smcr_link_clear(lnk, true);
@@ -1595,14 +1667,26 @@
 	mutex_unlock(&lgr->llc_conf_mutex);
 }
 
-/* Determine vlan of internal TCP socket.
- * @vlan_id: address to store the determined vlan id into
- */
+static int smc_vlan_by_tcpsk_walk(struct net_device *lower_dev,
+				  struct netdev_nested_priv *priv)
+{
+	unsigned short *vlan_id = (unsigned short *)priv->data;
+
+	if (is_vlan_dev(lower_dev)) {
+		*vlan_id = vlan_dev_vlan_id(lower_dev);
+		return 1;
+	}
+
+	return 0;
+}
+
+/* Determine vlan of internal TCP socket. */
 int smc_vlan_by_tcpsk(struct socket *clcsock, struct smc_init_info *ini)
 {
 	struct dst_entry *dst = sk_dst_get(clcsock->sk);
+	struct netdev_nested_priv priv;
 	struct net_device *ndev;
-	int i, nest_lvl, rc = 0;
+	int rc = 0;
 
 	ini->vlan_id = 0;
 	if (!dst) {
@@ -1620,20 +1704,9 @@
 		goto out_rel;
 	}
 
+	priv.data = (void *)&ini->vlan_id;
 	rtnl_lock();
-	nest_lvl = ndev->lower_level;
-	for (i = 0; i < nest_lvl; i++) {
-		struct list_head *lower = &ndev->adj_list.lower;
-
-		if (list_empty(lower))
-			break;
-		lower = lower->next;
-		ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
-		if (is_vlan_dev(ndev)) {
-			ini->vlan_id = vlan_dev_vlan_id(ndev);
-			break;
-		}
-	}
+	netdev_walk_all_lower_dev(ndev, smc_vlan_by_tcpsk_walk, &priv);
 	rtnl_unlock();
 
 out_rel:
@@ -1642,13 +1715,15 @@
 	return rc;
 }
 
-static bool smcr_lgr_match(struct smc_link_group *lgr,
-			   struct smc_clc_msg_local *lcl,
+static bool smcr_lgr_match(struct smc_link_group *lgr, u8 smcr_version,
+			   u8 peer_systemid[],
+			   u8 peer_gid[],
+			   u8 peer_mac_v1[],
 			   enum smc_lgr_role role, u32 clcqpn)
 {
 	int i;
 
-	if (memcmp(lgr->peer_systemid, lcl->id_for_peer, SMC_SYSTEMID_LEN) ||
+	if (memcmp(lgr->peer_systemid, peer_systemid, SMC_SYSTEMID_LEN) ||
 	    lgr->role != role)
 		return false;
 
@@ -1656,8 +1731,9 @@
 		if (!smc_link_active(&lgr->lnk[i]))
 			continue;
 		if ((lgr->role == SMC_SERV || lgr->lnk[i].peer_qpn == clcqpn) &&
-		    !memcmp(lgr->lnk[i].peer_gid, &lcl->gid, SMC_GID_SIZE) &&
-		    !memcmp(lgr->lnk[i].peer_mac, lcl->mac, sizeof(lcl->mac)))
+		    !memcmp(lgr->lnk[i].peer_gid, peer_gid, SMC_GID_SIZE) &&
+		    (smcr_version == SMC_V2 ||
+		     !memcmp(lgr->lnk[i].peer_mac, peer_mac_v1, ETH_ALEN)))
 			return true;
 	}
 	return false;
@@ -1696,12 +1772,16 @@
 		if ((ini->is_smcd ?
 		     smcd_lgr_match(lgr, ini->ism_dev[ini->ism_selected],
 				    ini->ism_peer_gid[ini->ism_selected]) :
-		     smcr_lgr_match(lgr, ini->ib_lcl, role, ini->ib_clcqpn)) &&
+		     smcr_lgr_match(lgr, ini->smcr_version,
+				    ini->peer_systemid,
+				    ini->peer_gid, ini->peer_mac, role,
+				    ini->ib_clcqpn)) &&
 		    !lgr->sync_err &&
 		    (ini->smcd_version == SMC_V2 ||
 		     lgr->vlan_id == ini->vlan_id) &&
 		    (role == SMC_CLNT || ini->is_smcd ||
-		     lgr->conns_num < SMC_RMBS_PER_LGR_MAX)) {
+		    (lgr->conns_num < SMC_RMBS_PER_LGR_MAX &&
+		      !bitmap_full(lgr->rtokens_used_mask, SMC_RMBS_PER_LGR_MAX)))) {
 			/* link group found */
 			ini->first_contact_local = 0;
 			conn->lgr = lgr;
@@ -1735,12 +1815,15 @@
 		write_lock_bh(&lgr->conns_lock);
 		rc = smc_lgr_register_conn(conn, true);
 		write_unlock_bh(&lgr->conns_lock);
-		if (rc)
+		if (rc) {
+			smc_lgr_cleanup_early(lgr);
 			goto out;
+		}
 	}
 	conn->local_tx_ctrl.common.type = SMC_CDC_MSG_TYPE;
 	conn->local_tx_ctrl.len = SMC_WR_TX_SIZE;
 	conn->urg_state = SMC_URG_READ;
+	init_waitqueue_head(&conn->cdc_pend_tx_wq);
 	INIT_WORK(&smc->conn.abort_work, smc_conn_abort_work);
 	if (ini->is_smcd) {
 		conn->rx_off = sizeof(struct smcd_cdc_msg);
@@ -1766,7 +1849,6 @@
  */
 static u8 smc_compress_bufsize(int size, bool is_smcd, bool is_rmb)
 {
-	const unsigned int max_scat = SG_MAX_SINGLE_ALLOC * PAGE_SIZE;
 	u8 compressed;
 
 	if (size <= SMC_BUF_MIN_SIZE)
@@ -1776,9 +1858,11 @@
 	compressed = min_t(u8, ilog2(size) + 1,
 			   is_smcd ? SMCD_DMBE_SIZES : SMCR_RMBE_SIZES);
 
+#ifdef CONFIG_ARCH_NO_SG_CHAIN
 	if (!is_smcd && is_rmb)
 		/* RMBs are backed by & limited to max size of scatterlists */
-		compressed = min_t(u8, compressed, ilog2(max_scat >> 14));
+		compressed = min_t(u8, compressed, ilog2((SG_MAX_SINGLE_ALLOC * PAGE_SIZE) >> 14));
+#endif
 
 	return compressed;
 }
@@ -1818,7 +1902,7 @@
  */
 static inline int smc_rmb_wnd_update_limit(int rmbe_size)
 {
-	return min_t(int, rmbe_size / 10, SOCK_MIN_SNDBUF / 2);
+	return max_t(int, rmbe_size / 10, SOCK_MIN_SNDBUF / 2);
 }
 
 /* map an rmb buf to a link */
@@ -1976,7 +2060,7 @@
 static int smcr_buf_map_usable_links(struct smc_link_group *lgr,
 				     struct smc_buf_desc *buf_desc, bool is_rmb)
 {
-	int i, rc = 0;
+	int i, rc = 0, cnt = 0;
 
 	/* protect against parallel link reconfiguration */
 	mutex_lock(&lgr->llc_conf_mutex);
@@ -1989,9 +2073,12 @@
 			rc = -ENOMEM;
 			goto out;
 		}
+		cnt++;
 	}
 out:
 	mutex_unlock(&lgr->llc_conf_mutex);
+	if (!rc && !cnt)
+		rc = -EINVAL;
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_core.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_core.h
@@ -42,11 +42,16 @@
 };
 
 #define SMC_WR_BUF_SIZE		48	/* size of work request buffer */
+#define SMC_WR_BUF_V2_SIZE	8192	/* size of v2 work request buffer */
 
 struct smc_wr_buf {
 	u8	raw[SMC_WR_BUF_SIZE];
 };
 
+struct smc_wr_v2_buf {
+	u8	raw[SMC_WR_BUF_V2_SIZE];
+};
+
 #define SMC_WR_REG_MR_WAIT_TIME	(5 * HZ)/* wait time for ib_wr_reg_mr result */
 
 enum smc_wr_reg_state {
@@ -92,7 +97,11 @@
 	struct smc_wr_tx_pend	*wr_tx_pends;	/* WR send waiting for CQE */
 	struct completion	*wr_tx_compl;	/* WR send CQE completion */
 	/* above four vectors have wr_tx_cnt elements and use the same index */
+	struct ib_send_wr	*wr_tx_v2_ib;	/* WR send v2 meta data */
+	struct ib_sge		*wr_tx_v2_sge;	/* WR send v2 gather meta data*/
+	struct smc_wr_tx_pend	*wr_tx_v2_pend;	/* WR send v2 waiting for CQE */
 	dma_addr_t		wr_tx_dma_addr;	/* DMA address of wr_tx_bufs */
+	dma_addr_t		wr_tx_v2_dma_addr; /* DMA address of v2 tx buf*/
 	atomic_long_t		wr_tx_id;	/* seq # of last sent WR */
 	unsigned long		*wr_tx_mask;	/* bit mask of used indexes */
 	u32			wr_tx_cnt;	/* number of WR send buffers */
@@ -104,6 +113,7 @@
 	struct ib_sge		*wr_rx_sges;	/* WR recv scatter meta data */
 	/* above three vectors have wr_rx_cnt elements and use the same index */
 	dma_addr_t		wr_rx_dma_addr;	/* DMA address of wr_rx_bufs */
+	dma_addr_t		wr_rx_v2_dma_addr; /* DMA address of v2 rx buf*/
 	u64			wr_rx_id;	/* seq # of last recv WR */
 	u32			wr_rx_cnt;	/* number of WR recv buffers */
 	unsigned long		wr_rx_tstamp;	/* jiffies when last buf rx */
@@ -208,6 +218,7 @@
 	SMC_LLC_FLOW_NONE	= 0,
 	SMC_LLC_FLOW_ADD_LINK	= 2,
 	SMC_LLC_FLOW_DEL_LINK	= 4,
+	SMC_LLC_FLOW_REQ_ADD_LINK = 5,
 	SMC_LLC_FLOW_RKEY	= 6,
 };
 
@@ -250,6 +261,10 @@
 						/* client or server */
 			struct smc_link		lnk[SMC_LINKS_PER_LGR_MAX];
 						/* smc link */
+			struct smc_wr_v2_buf	*wr_rx_buf_v2;
+						/* WR v2 recv payload buffer */
+			struct smc_wr_v2_buf	*wr_tx_buf_v2;
+						/* WR v2 send payload buffer */
 			char			peer_systemid[SMC_SYSTEMID_LEN];
 						/* unique system_id of peer */
 			struct smc_rtoken	rtokens[SMC_RMBS_PER_LGR_MAX]
@@ -288,6 +303,9 @@
 						/* link keep alive time */
 			u32			llc_termination_rsn;
 						/* rsn code for termination */
+			u8			nexthop_mac[ETH_ALEN];
+			u8			uses_gateway;
+			__be32			saddr;
 		};
 		struct { /* SMC-D */
 			u64			peer_gid;
@@ -302,6 +320,31 @@
 
 struct smc_clc_msg_local;
 
+#define GID_LIST_SIZE	2
+
+struct smc_gidlist {
+	u8			len;
+	u8			list[GID_LIST_SIZE][SMC_GID_SIZE];
+};
+
+struct smc_init_info_smcrv2 {
+	/* Input fields */
+	__be32			saddr;
+	struct sock		*clc_sk;
+	__be32			daddr;
+
+	/* Output fields when saddr is set */
+	struct smc_ib_device	*ib_dev_v2;
+	u8			ib_port_v2;
+	u8			ib_gid_v2[SMC_GID_SIZE];
+
+	/* Additional output fields when clc_sk and daddr is set as well */
+	u8			uses_gateway;
+	u8			nexthop_mac[ETH_ALEN];
+
+	struct smc_gidlist	gidlist;
+};
+
 struct smc_init_info {
 	u8			is_smcd;
 	u8			smc_type_v1;
@@ -310,12 +353,18 @@
 	u8			first_contact_local;
 	unsigned short		vlan_id;
 	u32			rc;
+	u8			negotiated_eid[SMC_MAX_EID_LEN];
 	/* SMC-R */
-	struct smc_clc_msg_local *ib_lcl;
+	u8			smcr_version;
+	u8			check_smcrv2;
+	u8			peer_gid[SMC_GID_SIZE];
+	u8			peer_mac[ETH_ALEN];
+	u8			peer_systemid[SMC_SYSTEMID_LEN];
 	struct smc_ib_device	*ib_dev;
 	u8			ib_gid[SMC_GID_SIZE];
 	u8			ib_port;
 	u32			ib_clcqpn;
+	struct smc_init_info_smcrv2 smcrv2;
 	/* SMC-D */
 	u64			ism_peer_gid[SMC_MAX_ISM_DEVS + 1];
 	struct smcd_dev		*ism_dev[SMC_MAX_ISM_DEVS + 1];
@@ -366,6 +415,12 @@
 	return true;
 }
 
+static inline bool smc_link_sendable(struct smc_link *lnk)
+{
+	return smc_link_usable(lnk) &&
+		lnk->qp_attr.cur_qp_state == IB_QPS_RTS;
+}
+
 static inline bool smc_link_active(struct smc_link *lnk)
 {
 	return lnk->state == SMC_LNK_ACTIVE;
@@ -413,7 +468,7 @@
 struct smc_sock;
 struct smc_clc_msg_accept_confirm;
 
-void smc_lgr_cleanup_early(struct smc_connection *conn);
+void smc_lgr_cleanup_early(struct smc_link_group *lgr);
 void smc_lgr_terminate_sched(struct smc_link_group *lgr);
 void smcr_port_add(struct smc_ib_device *smcibdev, u8 ibport);
 void smcr_port_err(struct smc_ib_device *smcibdev, u8 ibport);
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_diag.c
@@ -164,7 +164,7 @@
 	}
 	if (smc->conn.lgr && smc->conn.lgr->is_smcd &&
 	    (req->diag_ext & (1 << (SMC_DIAG_DMBINFO - 1))) &&
-	    !list_empty(&smc->conn.lgr->list)) {
+	    !list_empty(&smc->conn.lgr->list) && smc->conn.rmb_desc) {
 		struct smc_connection *conn = &smc->conn;
 		struct smcd_diag_dmbinfo dinfo;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_ib.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_ib.c
@@ -17,6 +17,7 @@
 #include <linux/scatterlist.h>
 #include <linux/wait.h>
 #include <linux/mutex.h>
+#include <linux/inetdevice.h>
 #include <rdma/ib_verbs.h>
 #include <rdma/ib_cache.h>
 
@@ -62,16 +63,23 @@
 		IB_QP_STATE | IB_QP_AV | IB_QP_PATH_MTU | IB_QP_DEST_QPN |
 		IB_QP_RQ_PSN | IB_QP_MAX_DEST_RD_ATOMIC | IB_QP_MIN_RNR_TIMER;
 	struct ib_qp_attr qp_attr;
+	u8 hop_lim = 1;
 
 	memset(&qp_attr, 0, sizeof(qp_attr));
 	qp_attr.qp_state = IB_QPS_RTR;
 	qp_attr.path_mtu = min(lnk->path_mtu, lnk->peer_mtu);
 	qp_attr.ah_attr.type = RDMA_AH_ATTR_TYPE_ROCE;
 	rdma_ah_set_port_num(&qp_attr.ah_attr, lnk->ibport);
-	rdma_ah_set_grh(&qp_attr.ah_attr, NULL, 0, lnk->sgid_index, 1, 0);
+	if (lnk->lgr->smc_version == SMC_V2 && lnk->lgr->uses_gateway)
+		hop_lim = IPV6_DEFAULT_HOPLIMIT;
+	rdma_ah_set_grh(&qp_attr.ah_attr, NULL, 0, lnk->sgid_index, hop_lim, 0);
 	rdma_ah_set_dgid_raw(&qp_attr.ah_attr, lnk->peer_gid);
-	memcpy(&qp_attr.ah_attr.roce.dmac, lnk->peer_mac,
-	       sizeof(lnk->peer_mac));
+	if (lnk->lgr->smc_version == SMC_V2 && lnk->lgr->uses_gateway)
+		memcpy(&qp_attr.ah_attr.roce.dmac, lnk->lgr->nexthop_mac,
+		       sizeof(lnk->lgr->nexthop_mac));
+	else
+		memcpy(&qp_attr.ah_attr.roce.dmac, lnk->peer_mac,
+		       sizeof(lnk->peer_mac));
 	qp_attr.dest_qp_num = lnk->peer_qpn;
 	qp_attr.rq_psn = lnk->peer_psn; /* starting receive packet seq # */
 	qp_attr.max_dest_rd_atomic = 1; /* max # of resources for incoming
@@ -101,12 +109,12 @@
 			    IB_QP_MAX_QP_RD_ATOMIC);
 }
 
-int smc_ib_modify_qp_reset(struct smc_link *lnk)
+int smc_ib_modify_qp_error(struct smc_link *lnk)
 {
 	struct ib_qp_attr qp_attr;
 
 	memset(&qp_attr, 0, sizeof(qp_attr));
-	qp_attr.qp_state = IB_QPS_RESET;
+	qp_attr.qp_state = IB_QPS_ERR;
 	return ib_modify_qp(lnk->roce_qp, &qp_attr, IB_QP_STATE);
 }
 
@@ -183,9 +191,86 @@
 	return smcibdev->pattr[ibport - 1].state == IB_PORT_ACTIVE;
 }
 
+int smc_ib_find_route(__be32 saddr, __be32 daddr,
+		      u8 nexthop_mac[], u8 *uses_gateway)
+{
+	struct neighbour *neigh = NULL;
+	struct rtable *rt = NULL;
+	struct flowi4 fl4 = {
+		.saddr = saddr,
+		.daddr = daddr
+	};
+
+	if (daddr == cpu_to_be32(INADDR_NONE))
+		goto out;
+	rt = ip_route_output_flow(&init_net, &fl4, NULL);
+	if (IS_ERR(rt))
+		goto out;
+	if (rt->rt_uses_gateway && rt->rt_gw_family != AF_INET)
+		goto out_rt;
+	neigh = dst_neigh_lookup(&rt->dst, &fl4.daddr);
+	if (!neigh)
+		goto out_rt;
+	memcpy(nexthop_mac, neigh->ha, ETH_ALEN);
+	*uses_gateway = rt->rt_uses_gateway;
+	neigh_release(neigh);
+	ip_rt_put(rt);
+	return 0;
+
+out_rt:
+	ip_rt_put(rt);
+out:
+	return -ENOENT;
+}
+
+static int smc_ib_determine_gid_rcu(const struct net_device *ndev,
+				    const struct ib_gid_attr *attr,
+				    u8 gid[], u8 *sgid_index,
+				    struct smc_init_info_smcrv2 *smcrv2)
+{
+	if (!smcrv2 && attr->gid_type == IB_GID_TYPE_ROCE) {
+		if (gid)
+			memcpy(gid, &attr->gid, SMC_GID_SIZE);
+		if (sgid_index)
+			*sgid_index = attr->index;
+		return 0;
+	}
+	if (smcrv2 && attr->gid_type == IB_GID_TYPE_ROCE_UDP_ENCAP &&
+	    smc_ib_gid_to_ipv4((u8 *)&attr->gid) != cpu_to_be32(INADDR_NONE)) {
+		struct in_device *in_dev = __in_dev_get_rcu(ndev);
+		const struct in_ifaddr *ifa;
+		bool subnet_match = false;
+
+		if (!in_dev)
+			goto out;
+		in_dev_for_each_ifa_rcu(ifa, in_dev) {
+			if (!inet_ifa_match(smcrv2->saddr, ifa))
+				continue;
+			subnet_match = true;
+			break;
+		}
+		if (!subnet_match)
+			goto out;
+		if (smcrv2->daddr && smc_ib_find_route(smcrv2->saddr,
+						       smcrv2->daddr,
+						       smcrv2->nexthop_mac,
+						       &smcrv2->uses_gateway))
+			goto out;
+
+		if (gid)
+			memcpy(gid, &attr->gid, SMC_GID_SIZE);
+		if (sgid_index)
+			*sgid_index = attr->index;
+		return 0;
+	}
+out:
+	return -ENODEV;
+}
+
 /* determine the gid for an ib-device port and vlan id */
 int smc_ib_determine_gid(struct smc_ib_device *smcibdev, u8 ibport,
-			 unsigned short vlan_id, u8 gid[], u8 *sgid_index)
+			 unsigned short vlan_id, u8 gid[], u8 *sgid_index,
+			 struct smc_init_info_smcrv2 *smcrv2)
 {
 	const struct ib_gid_attr *attr;
 	const struct net_device *ndev;
@@ -201,15 +286,13 @@
 		if (!IS_ERR(ndev) &&
 		    ((!vlan_id && !is_vlan_dev(ndev)) ||
 		     (vlan_id && is_vlan_dev(ndev) &&
-		      vlan_dev_vlan_id(ndev) == vlan_id)) &&
-		    attr->gid_type == IB_GID_TYPE_ROCE) {
-			rcu_read_unlock();
-			if (gid)
-				memcpy(gid, &attr->gid, SMC_GID_SIZE);
-			if (sgid_index)
-				*sgid_index = attr->index;
-			rdma_put_gid_attr(attr);
-			return 0;
+		      vlan_dev_vlan_id(ndev) == vlan_id))) {
+			if (!smc_ib_determine_gid_rcu(ndev, attr, gid,
+						      sgid_index, smcrv2)) {
+				rcu_read_unlock();
+				rdma_put_gid_attr(attr);
+				return 0;
+			}
 		}
 		rcu_read_unlock();
 		rdma_put_gid_attr(attr);
@@ -217,6 +300,58 @@
 	return -ENODEV;
 }
 
+/* check if gid is still defined on smcibdev */
+static bool smc_ib_check_link_gid(u8 gid[SMC_GID_SIZE], bool smcrv2,
+				  struct smc_ib_device *smcibdev, u8 ibport)
+{
+	const struct ib_gid_attr *attr;
+	bool rc = false;
+	int i;
+
+	for (i = 0; !rc && i < smcibdev->pattr[ibport - 1].gid_tbl_len; i++) {
+		attr = rdma_get_gid_attr(smcibdev->ibdev, ibport, i);
+		if (IS_ERR(attr))
+			continue;
+
+		rcu_read_lock();
+		if ((!smcrv2 && attr->gid_type == IB_GID_TYPE_ROCE) ||
+		    (smcrv2 && attr->gid_type == IB_GID_TYPE_ROCE_UDP_ENCAP &&
+		     !(ipv6_addr_type((const struct in6_addr *)&attr->gid)
+				     & IPV6_ADDR_LINKLOCAL)))
+			if (!memcmp(gid, &attr->gid, SMC_GID_SIZE))
+				rc = true;
+		rcu_read_unlock();
+		rdma_put_gid_attr(attr);
+	}
+	return rc;
+}
+
+/* check all links if the gid is still defined on smcibdev */
+static void smc_ib_gid_check(struct smc_ib_device *smcibdev, u8 ibport)
+{
+	struct smc_link_group *lgr;
+	int i;
+
+	spin_lock_bh(&smc_lgr_list.lock);
+	list_for_each_entry(lgr, &smc_lgr_list.list, list) {
+		if (strncmp(smcibdev->pnetid[ibport - 1], lgr->pnet_id,
+			    SMC_MAX_PNETID_LEN))
+			continue; /* lgr is not affected */
+		if (list_empty(&lgr->list))
+			continue;
+		for (i = 0; i < SMC_LINKS_PER_LGR_MAX; i++) {
+			if (lgr->lnk[i].state == SMC_LNK_UNUSED ||
+			    lgr->lnk[i].smcibdev != smcibdev)
+				continue;
+			if (!smc_ib_check_link_gid(lgr->lnk[i].gid,
+						   lgr->smc_version == SMC_V2,
+						   smcibdev, ibport))
+				smcr_port_err(smcibdev, ibport);
+		}
+	}
+	spin_unlock_bh(&smc_lgr_list.lock);
+}
+
 static int smc_ib_remember_port_attr(struct smc_ib_device *smcibdev, u8 ibport)
 {
 	int rc;
@@ -255,6 +390,7 @@
 		} else {
 			clear_bit(port_idx, smcibdev->ports_going_away);
 			smcr_port_add(smcibdev, port_idx + 1);
+			smc_ib_gid_check(smcibdev, port_idx + 1);
 		}
 	}
 }
@@ -523,6 +659,7 @@
 /* create a queue pair within the protection domain for a link */
 int smc_ib_create_queue_pair(struct smc_link *lnk)
 {
+	int sges_per_buf = (lnk->lgr->smc_version == SMC_V2) ? 2 : 1;
 	struct ib_qp_init_attr qp_attr = {
 		.event_handler = smc_ib_qp_event_handler,
 		.qp_context = lnk,
@@ -536,7 +673,7 @@
 			.max_send_wr = SMC_WR_BUF_CNT * 3,
 			.max_recv_wr = SMC_WR_BUF_CNT * 3,
 			.max_send_sge = SMC_IB_MAX_SEND_SGE,
-			.max_recv_sge = 1,
+			.max_recv_sge = sges_per_buf,
 		},
 		.sq_sig_type = IB_SIGNAL_REQ_WR,
 		.qp_type = IB_QPT_RC,
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_ib.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_ib.h
@@ -59,6 +59,17 @@
 	int			ndev_ifidx[SMC_MAX_PORTS]; /* ndev if indexes */
 };
 
+static inline __be32 smc_ib_gid_to_ipv4(u8 gid[SMC_GID_SIZE])
+{
+	struct in6_addr *addr6 = (struct in6_addr *)gid;
+
+	if (ipv6_addr_v4mapped(addr6) ||
+	    !(addr6->s6_addr32[0] | addr6->s6_addr32[1] | addr6->s6_addr32[2]))
+		return addr6->s6_addr32[3];
+	return cpu_to_be32(INADDR_NONE);
+}
+
+struct smc_init_info_smcrv2;
 struct smc_buf_desc;
 struct smc_link;
 
@@ -79,6 +90,7 @@
 int smc_ib_ready_link(struct smc_link *lnk);
 int smc_ib_modify_qp_rts(struct smc_link *lnk);
 int smc_ib_modify_qp_reset(struct smc_link *lnk);
+int smc_ib_modify_qp_error(struct smc_link *lnk);
 long smc_ib_setup_per_ibdev(struct smc_ib_device *smcibdev);
 int smc_ib_get_memory_region(struct ib_pd *pd, int access_flags,
 			     struct smc_buf_desc *buf_slot, u8 link_idx);
@@ -90,7 +102,10 @@
 			       struct smc_buf_desc *buf_slot,
 			       enum dma_data_direction data_direction);
 int smc_ib_determine_gid(struct smc_ib_device *smcibdev, u8 ibport,
-			 unsigned short vlan_id, u8 gid[], u8 *sgid_index);
+			 unsigned short vlan_id, u8 gid[], u8 *sgid_index,
+			 struct smc_init_info_smcrv2 *smcrv2);
+int smc_ib_find_route(__be32 saddr, __be32 daddr,
+		      u8 nexthop_mac[], u8 *uses_gateway);
 bool smc_ib_is_valid_local_systemid(void);
 int smcr_nl_get_device(struct sk_buff *skb, struct netlink_callback *cb);
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_ism.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_ism.c
@@ -23,6 +23,7 @@
 };
 
 static bool smc_ism_v2_capable;
+static u8 smc_ism_v2_system_eid[SMC_MAX_EID_LEN];
 
 /* Test if an ISM communication is possible - same CPC */
 int smc_ism_cantalk(u64 peer_gid, unsigned short vlan_id, struct smcd_dev *smcd)
@@ -42,9 +43,12 @@
 	return rc < 0 ? rc : 0;
 }
 
-void smc_ism_get_system_eid(struct smcd_dev *smcd, u8 **eid)
+void smc_ism_get_system_eid(u8 **eid)
 {
-	smcd->ops->get_system_eid(smcd, eid);
+	if (!smc_ism_v2_capable)
+		*eid = NULL;
+	else
+		*eid = smc_ism_v2_system_eid;
 }
 
 u16 smc_ism_get_chid(struct smcd_dev *smcd)
@@ -435,9 +439,12 @@
 	if (list_empty(&smcd_dev_list.list)) {
 		u8 *system_eid = NULL;
 
-		smc_ism_get_system_eid(smcd, &system_eid);
-		if (system_eid[24] != '0' || system_eid[28] != '0')
+		smcd->ops->get_system_eid(smcd, &system_eid);
+		if (system_eid[24] != '0' || system_eid[28] != '0') {
 			smc_ism_v2_capable = true;
+			memcpy(smc_ism_v2_system_eid, system_eid,
+			       SMC_MAX_EID_LEN);
+		}
 	}
 	/* sort list: devices without pnetid before devices with pnetid */
 	if (smcd->pnetid[0])
@@ -533,4 +540,5 @@
 void __init smc_ism_init(void)
 {
 	smc_ism_v2_capable = false;
+	memset(smc_ism_v2_system_eid, 0, SMC_MAX_EID_LEN);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_ism.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_ism.h
@@ -48,7 +48,7 @@
 int smc_ism_write(struct smcd_dev *dev, const struct smc_ism_position *pos,
 		  void *data, size_t len);
 int smc_ism_signal_shutdown(struct smc_link_group *lgr);
-void smc_ism_get_system_eid(struct smcd_dev *dev, u8 **eid);
+void smc_ism_get_system_eid(u8 **eid);
 u16 smc_ism_get_chid(struct smcd_dev *dev);
 bool smc_ism_is_v2_capable(void);
 void smc_ism_init(void);
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_llc.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_llc.c
@@ -23,16 +23,24 @@
 
 struct smc_llc_hdr {
 	struct smc_wr_rx_hdr common;
-	u8 length;	/* 44 */
-#if defined(__BIG_ENDIAN_BITFIELD)
-	u8 reserved:4,
-	   add_link_rej_rsn:4;
+	union {
+		struct {
+			u8 length;	/* 44 */
+	#if defined(__BIG_ENDIAN_BITFIELD)
+			u8 reserved:4,
+			   add_link_rej_rsn:4;
 #elif defined(__LITTLE_ENDIAN_BITFIELD)
-	u8 add_link_rej_rsn:4,
-	   reserved:4;
+			u8 add_link_rej_rsn:4,
+			   reserved:4;
 #endif
+		};
+		u16 length_v2;	/* 44 - 8192*/
+	};
 	u8 flags;
-};
+} __packed;		/* format defined in
+			 * IBM Shared Memory Communications Version 2
+			 * (https://www.ibm.com/support/pages/node/6326337)
+			 */
 
 #define SMC_LLC_FLAG_NO_RMBE_EYEC	0x03
 
@@ -76,6 +84,32 @@
 	__be64 rmb_vaddr_new;
 };
 
+struct smc_llc_msg_add_link_v2_ext {
+#if defined(__BIG_ENDIAN_BITFIELD)
+	u8 v2_direct : 1,
+	   reserved  : 7;
+#elif defined(__LITTLE_ENDIAN_BITFIELD)
+	u8 reserved  : 7,
+	   v2_direct : 1;
+#endif
+	u8 reserved2;
+	u8 client_target_gid[SMC_GID_SIZE];
+	u8 reserved3[8];
+	u16 num_rkeys;
+	struct smc_llc_msg_add_link_cont_rt rt[];
+} __packed;		/* format defined in
+			 * IBM Shared Memory Communications Version 2
+			 * (https://www.ibm.com/support/pages/node/6326337)
+			 */
+
+struct smc_llc_msg_req_add_link_v2 {
+	struct smc_llc_hdr hd;
+	u8 reserved[20];
+	u8 gid_cnt;
+	u8 reserved2[3];
+	u8 gid[][SMC_GID_SIZE];
+};
+
 #define SMC_LLC_RKEYS_PER_CONT_MSG	2
 
 struct smc_llc_msg_add_link_cont {	/* type 0x03 */
@@ -114,7 +148,8 @@
 	__be64 rmb_vaddr;
 } __packed;			/* format defined in RFC7609 */
 
-#define SMC_LLC_RKEYS_PER_MSG	3
+#define SMC_LLC_RKEYS_PER_MSG		3
+#define SMC_LLC_RKEYS_PER_MSG_V2	255
 
 struct smc_llc_msg_confirm_rkey {	/* type 0x06 */
 	struct smc_llc_hdr hd;
@@ -135,9 +170,18 @@
 	u8 reserved2[4];
 };
 
+struct smc_llc_msg_delete_rkey_v2 {	/* type 0x29 */
+	struct smc_llc_hdr hd;
+	u8 num_rkeys;
+	u8 num_inval_rkeys;
+	u8 reserved[2];
+	__be32 rkey[];
+};
+
 union smc_llc_msg {
 	struct smc_llc_msg_confirm_link confirm_link;
 	struct smc_llc_msg_add_link add_link;
+	struct smc_llc_msg_req_add_link_v2 req_add_link;
 	struct smc_llc_msg_add_link_cont add_link_cont;
 	struct smc_llc_msg_del_link delete_link;
 
@@ -189,7 +233,7 @@
 static void smc_llc_flow_parallel(struct smc_link_group *lgr, u8 flow_type,
 				  struct smc_llc_qentry *qentry)
 {
-	u8 msg_type = qentry->msg.raw.hdr.common.type;
+	u8 msg_type = qentry->msg.raw.hdr.common.llc_type;
 
 	if ((msg_type == SMC_LLC_ADD_LINK || msg_type == SMC_LLC_DELETE_LINK) &&
 	    flow_type != msg_type && !lgr->delayed_event) {
@@ -219,7 +263,7 @@
 		spin_unlock_bh(&lgr->llc_flow_lock);
 		return false;
 	}
-	switch (qentry->msg.raw.hdr.common.type) {
+	switch (qentry->msg.raw.hdr.common.llc_type) {
 	case SMC_LLC_ADD_LINK:
 		flow->type = SMC_LLC_FLOW_ADD_LINK;
 		break;
@@ -306,7 +350,7 @@
 		smc_llc_flow_qentry_del(flow);
 		goto out;
 	}
-	rcv_msg = flow->qentry->msg.raw.hdr.common.type;
+	rcv_msg = flow->qentry->msg.raw.hdr.common.llc_type;
 	if (exp_msg && rcv_msg != exp_msg) {
 		if (exp_msg == SMC_LLC_ADD_LINK &&
 		    rcv_msg == SMC_LLC_DELETE_LINK) {
@@ -374,6 +418,30 @@
 	return 0;
 }
 
+static int smc_llc_add_pending_send_v2(struct smc_link *link,
+				       struct smc_wr_v2_buf **wr_buf,
+				       struct smc_wr_tx_pend_priv **pend)
+{
+	int rc;
+
+	rc = smc_wr_tx_get_v2_slot(link, smc_llc_tx_handler, wr_buf, pend);
+	if (rc < 0)
+		return rc;
+	return 0;
+}
+
+static void smc_llc_init_msg_hdr(struct smc_llc_hdr *hdr,
+				 struct smc_link_group *lgr, size_t len)
+{
+	if (lgr->smc_version == SMC_V2) {
+		hdr->common.llc_version = SMC_V2;
+		hdr->length_v2 = len;
+	} else {
+		hdr->common.llc_version = 0;
+		hdr->length = len;
+	}
+}
+
 /* high-level API to send LLC confirm link */
 int smc_llc_send_confirm_link(struct smc_link *link,
 			      enum smc_llc_reqresp reqresp)
@@ -390,8 +458,8 @@
 		goto put_out;
 	confllc = (struct smc_llc_msg_confirm_link *)wr_buf;
 	memset(confllc, 0, sizeof(*confllc));
-	confllc->hd.common.type = SMC_LLC_CONFIRM_LINK;
-	confllc->hd.length = sizeof(struct smc_llc_msg_confirm_link);
+	confllc->hd.common.llc_type = SMC_LLC_CONFIRM_LINK;
+	smc_llc_init_msg_hdr(&confllc->hd, link->lgr, sizeof(*confllc));
 	confllc->hd.flags |= SMC_LLC_FLAG_NO_RMBE_EYEC;
 	if (reqresp == SMC_LLC_RESP)
 		confllc->hd.flags |= SMC_LLC_FLAG_RESP;
@@ -426,8 +494,8 @@
 		goto put_out;
 	rkeyllc = (struct smc_llc_msg_confirm_rkey *)wr_buf;
 	memset(rkeyllc, 0, sizeof(*rkeyllc));
-	rkeyllc->hd.common.type = SMC_LLC_CONFIRM_RKEY;
-	rkeyllc->hd.length = sizeof(struct smc_llc_msg_confirm_rkey);
+	rkeyllc->hd.common.llc_type = SMC_LLC_CONFIRM_RKEY;
+	smc_llc_init_msg_hdr(&rkeyllc->hd, send_link->lgr, sizeof(*rkeyllc));
 
 	rtok_ix = 1;
 	for (i = 0; i < SMC_LINKS_PER_LGR_MAX; i++) {
@@ -471,8 +539,8 @@
 		goto put_out;
 	rkeyllc = (struct smc_llc_msg_delete_rkey *)wr_buf;
 	memset(rkeyllc, 0, sizeof(*rkeyllc));
-	rkeyllc->hd.common.type = SMC_LLC_DELETE_RKEY;
-	rkeyllc->hd.length = sizeof(struct smc_llc_msg_delete_rkey);
+	rkeyllc->hd.common.llc_type = SMC_LLC_DELETE_RKEY;
+	smc_llc_init_msg_hdr(&rkeyllc->hd, link->lgr, sizeof(*rkeyllc));
 	rkeyllc->num_rkeys = 1;
 	rkeyllc->rkey[0] = htonl(rmb_desc->mr_rx[link->link_idx]->rkey);
 	/* send llc message */
@@ -482,26 +550,116 @@
 	return rc;
 }
 
+/* return first buffer from any of the next buf lists */
+static struct smc_buf_desc *_smc_llc_get_next_rmb(struct smc_link_group *lgr,
+						  int *buf_lst)
+{
+	struct smc_buf_desc *buf_pos;
+
+	while (*buf_lst < SMC_RMBE_SIZES) {
+		buf_pos = list_first_entry_or_null(&lgr->rmbs[*buf_lst],
+						   struct smc_buf_desc, list);
+		if (buf_pos)
+			return buf_pos;
+		(*buf_lst)++;
+	}
+	return NULL;
+}
+
+/* return next rmb from buffer lists */
+static struct smc_buf_desc *smc_llc_get_next_rmb(struct smc_link_group *lgr,
+						 int *buf_lst,
+						 struct smc_buf_desc *buf_pos)
+{
+	struct smc_buf_desc *buf_next;
+
+	if (!buf_pos || list_is_last(&buf_pos->list, &lgr->rmbs[*buf_lst])) {
+		(*buf_lst)++;
+		return _smc_llc_get_next_rmb(lgr, buf_lst);
+	}
+	buf_next = list_next_entry(buf_pos, list);
+	return buf_next;
+}
+
+static struct smc_buf_desc *smc_llc_get_first_rmb(struct smc_link_group *lgr,
+						  int *buf_lst)
+{
+	*buf_lst = 0;
+	return smc_llc_get_next_rmb(lgr, buf_lst, NULL);
+}
+
+static int smc_llc_fill_ext_v2(struct smc_llc_msg_add_link_v2_ext *ext,
+			       struct smc_link *link, struct smc_link *link_new)
+{
+	struct smc_link_group *lgr = link->lgr;
+	struct smc_buf_desc *buf_pos;
+	int prim_lnk_idx, lnk_idx, i;
+	struct smc_buf_desc *rmb;
+	int len = sizeof(*ext);
+	int buf_lst;
+
+	ext->v2_direct = !lgr->uses_gateway;
+	memcpy(ext->client_target_gid, link_new->gid, SMC_GID_SIZE);
+
+	prim_lnk_idx = link->link_idx;
+	lnk_idx = link_new->link_idx;
+	mutex_lock(&lgr->rmbs_lock);
+	ext->num_rkeys = lgr->conns_num;
+	if (!ext->num_rkeys)
+		goto out;
+	buf_pos = smc_llc_get_first_rmb(lgr, &buf_lst);
+	for (i = 0; i < ext->num_rkeys; i++) {
+		if (!buf_pos)
+			break;
+		rmb = buf_pos;
+		ext->rt[i].rmb_key = htonl(rmb->mr_rx[prim_lnk_idx]->rkey);
+		ext->rt[i].rmb_key_new = htonl(rmb->mr_rx[lnk_idx]->rkey);
+		ext->rt[i].rmb_vaddr_new =
+			cpu_to_be64((u64)sg_dma_address(rmb->sgt[lnk_idx].sgl));
+		buf_pos = smc_llc_get_next_rmb(lgr, &buf_lst, buf_pos);
+		while (buf_pos && !(buf_pos)->used)
+			buf_pos = smc_llc_get_next_rmb(lgr, &buf_lst, buf_pos);
+	}
+	len += i * sizeof(ext->rt[0]);
+out:
+	mutex_unlock(&lgr->rmbs_lock);
+	return len;
+}
+
 /* send ADD LINK request or response */
 int smc_llc_send_add_link(struct smc_link *link, u8 mac[], u8 gid[],
 			  struct smc_link *link_new,
 			  enum smc_llc_reqresp reqresp)
 {
+	struct smc_llc_msg_add_link_v2_ext *ext = NULL;
 	struct smc_llc_msg_add_link *addllc;
 	struct smc_wr_tx_pend_priv *pend;
-	struct smc_wr_buf *wr_buf;
+	int len = sizeof(*addllc);
 	int rc;
 
 	if (!smc_wr_tx_link_hold(link))
 		return -ENOLINK;
-	rc = smc_llc_add_pending_send(link, &wr_buf, &pend);
-	if (rc)
-		goto put_out;
-	addllc = (struct smc_llc_msg_add_link *)wr_buf;
+	if (link->lgr->smc_version == SMC_V2) {
+		struct smc_wr_v2_buf *wr_buf;
+
+		rc = smc_llc_add_pending_send_v2(link, &wr_buf, &pend);
+		if (rc)
+			goto put_out;
+		addllc = (struct smc_llc_msg_add_link *)wr_buf;
+		ext = (struct smc_llc_msg_add_link_v2_ext *)
+						&wr_buf->raw[sizeof(*addllc)];
+		memset(ext, 0, SMC_WR_TX_SIZE);
+	} else {
+		struct smc_wr_buf *wr_buf;
+
+		rc = smc_llc_add_pending_send(link, &wr_buf, &pend);
+		if (rc)
+			goto put_out;
+		addllc = (struct smc_llc_msg_add_link *)wr_buf;
+	}
 
 	memset(addllc, 0, sizeof(*addllc));
-	addllc->hd.common.type = SMC_LLC_ADD_LINK;
-	addllc->hd.length = sizeof(struct smc_llc_msg_add_link);
+	addllc->hd.common.llc_type = SMC_LLC_ADD_LINK;
 	if (reqresp == SMC_LLC_RESP)
 		addllc->hd.flags |= SMC_LLC_FLAG_RESP;
 	memcpy(addllc->sender_mac, mac, ETH_ALEN);
@@ -516,8 +674,14 @@
 			addllc->qp_mtu = min(link_new->path_mtu,
 					     link_new->peer_mtu);
 	}
+	if (ext && link_new)
+		len += smc_llc_fill_ext_v2(ext, link, link_new);
+	smc_llc_init_msg_hdr(&addllc->hd, link->lgr, len);
 	/* send llc message */
-	rc = smc_wr_tx_send(link, pend);
+	if (link->lgr->smc_version == SMC_V2)
+		rc = smc_wr_tx_v2_send(link, pend, len);
+	else
+		rc = smc_wr_tx_send(link, pend);
 put_out:
 	smc_wr_tx_link_put(link);
 	return rc;
@@ -541,8 +705,8 @@
 	delllc = (struct smc_llc_msg_del_link *)wr_buf;
 
 	memset(delllc, 0, sizeof(*delllc));
-	delllc->hd.common.type = SMC_LLC_DELETE_LINK;
-	delllc->hd.length = sizeof(struct smc_llc_msg_del_link);
+	delllc->hd.common.llc_type = SMC_LLC_DELETE_LINK;
+	smc_llc_init_msg_hdr(&delllc->hd, link->lgr, sizeof(*delllc));
 	if (reqresp == SMC_LLC_RESP)
 		delllc->hd.flags |= SMC_LLC_FLAG_RESP;
 	if (orderly)
@@ -574,8 +738,8 @@
 		goto put_out;
 	testllc = (struct smc_llc_msg_test_link *)wr_buf;
 	memset(testllc, 0, sizeof(*testllc));
-	testllc->hd.common.type = SMC_LLC_TEST_LINK;
-	testllc->hd.length = sizeof(struct smc_llc_msg_test_link);
+	testllc->hd.common.llc_type = SMC_LLC_TEST_LINK;
+	smc_llc_init_msg_hdr(&testllc->hd, link->lgr, sizeof(*testllc));
 	memcpy(testllc->user_data, user_data, sizeof(testllc->user_data));
 	/* send llc message */
 	rc = smc_wr_tx_send(link, pend);
@@ -651,44 +815,6 @@
 	return -EMLINK;
 }
 
-/* return first buffer from any of the next buf lists */
-static struct smc_buf_desc *_smc_llc_get_next_rmb(struct smc_link_group *lgr,
-						  int *buf_lst)
-{
-	struct smc_buf_desc *buf_pos;
-
-	while (*buf_lst < SMC_RMBE_SIZES) {
-		buf_pos = list_first_entry_or_null(&lgr->rmbs[*buf_lst],
-						   struct smc_buf_desc, list);
-		if (buf_pos)
-			return buf_pos;
-		(*buf_lst)++;
-	}
-	return NULL;
-}
-
-/* return next rmb from buffer lists */
-static struct smc_buf_desc *smc_llc_get_next_rmb(struct smc_link_group *lgr,
-						 int *buf_lst,
-						 struct smc_buf_desc *buf_pos)
-{
-	struct smc_buf_desc *buf_next;
-
-	if (!buf_pos || list_is_last(&buf_pos->list, &lgr->rmbs[*buf_lst])) {
-		(*buf_lst)++;
-		return _smc_llc_get_next_rmb(lgr, buf_lst);
-	}
-	buf_next = list_next_entry(buf_pos, list);
-	return buf_next;
-}
-
-static struct smc_buf_desc *smc_llc_get_first_rmb(struct smc_link_group *lgr,
-						  int *buf_lst)
-{
-	*buf_lst = 0;
-	return smc_llc_get_next_rmb(lgr, buf_lst, NULL);
-}
-
 /* send one add_link_continue msg */
 static int smc_llc_add_link_cont(struct smc_link *link,
 				 struct smc_link *link_new, u8 *num_rkeys_todo,
@@ -716,6 +842,8 @@
 	addc_llc->num_rkeys = *num_rkeys_todo;
 	n = *num_rkeys_todo;
 	for (i = 0; i < min_t(u8, n, SMC_LLC_RKEYS_PER_CONT_MSG); i++) {
+		while (*buf_pos && !(*buf_pos)->used)
+			*buf_pos = smc_llc_get_next_rmb(lgr, buf_lst, *buf_pos);
 		if (!*buf_pos) {
 			addc_llc->num_rkeys = addc_llc->num_rkeys -
 					      *num_rkeys_todo;
@@ -731,10 +859,8 @@
 
 		(*num_rkeys_todo)--;
 		*buf_pos = smc_llc_get_next_rmb(lgr, buf_lst, *buf_pos);
-		while (*buf_pos && !(*buf_pos)->used)
-			*buf_pos = smc_llc_get_next_rmb(lgr, buf_lst, *buf_pos);
 	}
-	addc_llc->hd.common.type = SMC_LLC_ADD_LINK_CONT;
+	addc_llc->hd.common.llc_type = SMC_LLC_ADD_LINK_CONT;
 	addc_llc->hd.length = sizeof(struct smc_llc_msg_add_link_cont);
 	if (lgr->role == SMC_CLNT)
 		addc_llc->hd.flags |= SMC_LLC_FLAG_RESP;
@@ -793,6 +919,8 @@
 	qentry->msg.raw.hdr.flags |= SMC_LLC_FLAG_RESP;
 	qentry->msg.raw.hdr.flags |= SMC_LLC_FLAG_ADD_LNK_REJ;
 	qentry->msg.raw.hdr.add_link_rej_rsn = SMC_LLC_REJ_RSN_NO_ALT_PATH;
+	smc_llc_init_msg_hdr(&qentry->msg.raw.hdr, qentry->link->lgr,
+			     sizeof(qentry->msg));
 	return smc_llc_send_message(qentry->link, &qentry->msg);
 }
 
@@ -813,7 +941,7 @@
 					      SMC_LLC_DEL_LOST_PATH);
 		return -ENOLINK;
 	}
-	if (qentry->msg.raw.hdr.common.type != SMC_LLC_CONFIRM_LINK) {
+	if (qentry->msg.raw.hdr.common.llc_type != SMC_LLC_CONFIRM_LINK) {
 		/* received DELETE_LINK instead */
 		qentry->msg.raw.hdr.flags |= SMC_LLC_FLAG_RESP;
 		smc_llc_send_message(link, &qentry->msg);
@@ -854,6 +982,26 @@
 	return 0;
 }
 
+static void smc_llc_save_add_link_rkeys(struct smc_link *link,
+					struct smc_link *link_new)
+{
+	struct smc_llc_msg_add_link_v2_ext *ext;
+	struct smc_link_group *lgr = link->lgr;
+	int max, i;
+
+	ext = (struct smc_llc_msg_add_link_v2_ext *)((u8 *)lgr->wr_rx_buf_v2 +
+						     SMC_WR_TX_SIZE);
+	max = min_t(u8, ext->num_rkeys, SMC_LLC_RKEYS_PER_MSG_V2);
+	mutex_lock(&lgr->rmbs_lock);
+	for (i = 0; i < max; i++) {
+		smc_rtoken_set(lgr, link->link_idx, link_new->link_idx,
+			       ext->rt[i].rmb_key,
+			       ext->rt[i].rmb_vaddr_new,
+			       ext->rt[i].rmb_key_new);
+	}
+	mutex_unlock(&lgr->rmbs_lock);
+}
+
 static void smc_llc_save_add_link_info(struct smc_link *link,
 				       struct smc_llc_msg_add_link *add_llc)
 {
@@ -870,31 +1018,47 @@
 	struct smc_llc_msg_add_link *llc = &qentry->msg.add_link;
 	enum smc_lgr_type lgr_new_t = SMC_LGR_SYMMETRIC;
 	struct smc_link_group *lgr = smc_get_lgr(link);
+	struct smc_init_info *ini = NULL;
 	struct smc_link *lnk_new = NULL;
-	struct smc_init_info ini;
 	int lnk_idx, rc = 0;
 
 	if (!llc->qp_mtu)
 		goto out_reject;
 
-	ini.vlan_id = lgr->vlan_id;
-	smc_pnet_find_alt_roce(lgr, &ini, link->smcibdev);
+	ini = kzalloc(sizeof(*ini), GFP_KERNEL);
+	if (!ini) {
+		rc = -ENOMEM;
+		goto out_reject;
+	}
+
+	ini->vlan_id = lgr->vlan_id;
+	if (lgr->smc_version == SMC_V2) {
+		ini->check_smcrv2 = true;
+		ini->smcrv2.saddr = lgr->saddr;
+		ini->smcrv2.daddr = smc_ib_gid_to_ipv4(llc->sender_gid);
+	}
+	smc_pnet_find_alt_roce(lgr, ini, link->smcibdev);
 	if (!memcmp(llc->sender_gid, link->peer_gid, SMC_GID_SIZE) &&
-	    !memcmp(llc->sender_mac, link->peer_mac, ETH_ALEN)) {
-		if (!ini.ib_dev)
+	    (lgr->smc_version == SMC_V2 ||
+	     !memcmp(llc->sender_mac, link->peer_mac, ETH_ALEN))) {
+		if (!ini->ib_dev && !ini->smcrv2.ib_dev_v2)
 			goto out_reject;
 		lgr_new_t = SMC_LGR_ASYMMETRIC_PEER;
 	}
-	if (!ini.ib_dev) {
+	if (lgr->smc_version == SMC_V2 && !ini->smcrv2.ib_dev_v2) {
 		lgr_new_t = SMC_LGR_ASYMMETRIC_LOCAL;
-		ini.ib_dev = link->smcibdev;
-		ini.ib_port = link->ibport;
+		ini->smcrv2.ib_dev_v2 = link->smcibdev;
+		ini->smcrv2.ib_port_v2 = link->ibport;
+	} else if (lgr->smc_version < SMC_V2 && !ini->ib_dev) {
+		lgr_new_t = SMC_LGR_ASYMMETRIC_LOCAL;
+		ini->ib_dev = link->smcibdev;
+		ini->ib_port = link->ibport;
 	}
 	lnk_idx = smc_llc_alloc_alt_link(lgr, lgr_new_t);
 	if (lnk_idx < 0)
 		goto out_reject;
 	lnk_new = &lgr->lnk[lnk_idx];
-	rc = smcr_link_init(lgr, lnk_new, lnk_idx, &ini);
+	rc = smcr_link_init(lgr, lnk_new, lnk_idx, ini);
 	if (rc)
 		goto out_reject;
 	smc_llc_save_add_link_info(lnk_new, llc);
@@ -910,16 +1074,20 @@
 		goto out_clear_lnk;
 
 	rc = smc_llc_send_add_link(link,
-				   lnk_new->smcibdev->mac[ini.ib_port - 1],
+				   lnk_new->smcibdev->mac[lnk_new->ibport - 1],
 				   lnk_new->gid, lnk_new, SMC_LLC_RESP);
 	if (rc)
 		goto out_clear_lnk;
-	rc = smc_llc_cli_rkey_exchange(link, lnk_new);
-	if (rc) {
-		rc = 0;
-		goto out_clear_lnk;
+	if (lgr->smc_version == SMC_V2) {
+		smc_llc_save_add_link_rkeys(link, lnk_new);
+	} else {
+		rc = smc_llc_cli_rkey_exchange(link, lnk_new);
+		if (rc) {
+			rc = 0;
+			goto out_clear_lnk;
+		}
 	}
-	rc = smc_llc_cli_conf_link(link, &ini, lnk_new, lgr_new_t);
+	rc = smc_llc_cli_conf_link(link, ini, lnk_new, lgr_new_t);
 	if (!rc)
 		goto out;
 out_clear_lnk:
@@ -928,29 +1096,78 @@
 out_reject:
 	smc_llc_cli_add_link_reject(qentry);
 out:
+	kfree(ini);
 	kfree(qentry);
 	return rc;
 }
 
+static void smc_llc_send_request_add_link(struct smc_link *link)
+{
+	struct smc_llc_msg_req_add_link_v2 *llc;
+	struct smc_wr_tx_pend_priv *pend;
+	struct smc_wr_v2_buf *wr_buf;
+	struct smc_gidlist gidlist;
+	int rc, len, i;
+
+	if (!smc_wr_tx_link_hold(link))
+		return;
+	if (link->lgr->type == SMC_LGR_SYMMETRIC ||
+	    link->lgr->type == SMC_LGR_ASYMMETRIC_PEER)
+		goto put_out;
+
+	smc_fill_gid_list(link->lgr, &gidlist, link->smcibdev, link->gid);
+	if (gidlist.len <= 1)
+		goto put_out;
+
+	rc = smc_llc_add_pending_send_v2(link, &wr_buf, &pend);
+	if (rc)
+		goto put_out;
+	llc = (struct smc_llc_msg_req_add_link_v2 *)wr_buf;
+	memset(llc, 0, SMC_WR_TX_SIZE);
+
+	llc->hd.common.llc_type = SMC_LLC_REQ_ADD_LINK;
+	for (i = 0; i < gidlist.len; i++)
+		memcpy(llc->gid[i], gidlist.list[i], sizeof(gidlist.list[0]));
+	llc->gid_cnt = gidlist.len;
+	len = sizeof(*llc) + (gidlist.len * sizeof(gidlist.list[0]));
+	smc_llc_init_msg_hdr(&llc->hd, link->lgr, len);
+	rc = smc_wr_tx_v2_send(link, pend, len);
+	if (!rc)
+		/* set REQ_ADD_LINK flow and wait for response from peer */
+		link->lgr->llc_flow_lcl.type = SMC_LLC_FLOW_REQ_ADD_LINK;
+put_out:
+	smc_wr_tx_link_put(link);
+}
+
 /* as an SMC client, invite server to start the add_link processing */
 static void smc_llc_cli_add_link_invite(struct smc_link *link,
 					struct smc_llc_qentry *qentry)
 {
 	struct smc_link_group *lgr = smc_get_lgr(link);
-	struct smc_init_info ini;
+	struct smc_init_info *ini = NULL;
+
+	if (lgr->smc_version == SMC_V2) {
+		smc_llc_send_request_add_link(link);
+		goto out;
+	}
 
 	if (lgr->type == SMC_LGR_SYMMETRIC ||
 	    lgr->type == SMC_LGR_ASYMMETRIC_PEER)
 		goto out;
 
-	ini.vlan_id = lgr->vlan_id;
-	smc_pnet_find_alt_roce(lgr, &ini, link->smcibdev);
-	if (!ini.ib_dev)
+	ini = kzalloc(sizeof(*ini), GFP_KERNEL);
+	if (!ini)
+		goto out;
+
+	ini->vlan_id = lgr->vlan_id;
+	smc_pnet_find_alt_roce(lgr, ini, link->smcibdev);
+	if (!ini->ib_dev)
 		goto out;
 
-	smc_llc_send_add_link(link, ini.ib_dev->mac[ini.ib_port - 1],
-			      ini.ib_gid, NULL, SMC_LLC_REQ);
+	smc_llc_send_add_link(link, ini->ib_dev->mac[ini->ib_port - 1],
+			      ini->ib_gid, NULL, SMC_LLC_REQ);
 out:
+	kfree(ini);
 	kfree(qentry);
 }
 
@@ -966,7 +1183,7 @@
 
 static bool smc_llc_is_local_add_link(union smc_llc_msg *llc)
 {
-	if (llc->raw.hdr.common.type == SMC_LLC_ADD_LINK &&
+	if (llc->raw.hdr.common.llc_type == SMC_LLC_ADD_LINK &&
 	    smc_llc_is_empty_llc_message(llc))
 		return true;
 	return false;
@@ -1133,7 +1350,7 @@
 	/* receive CONFIRM LINK response over the RoCE fabric */
 	qentry = smc_llc_wait(lgr, link, SMC_LLC_WAIT_FIRST_TIME, 0);
 	if (!qentry ||
-	    qentry->msg.raw.hdr.common.type != SMC_LLC_CONFIRM_LINK) {
+	    qentry->msg.raw.hdr.common.llc_type != SMC_LLC_CONFIRM_LINK) {
 		/* send DELETE LINK */
 		smc_llc_send_delete_link(link, link_new->link_id, SMC_LLC_REQ,
 					 false, SMC_LLC_DEL_LOST_PATH);
@@ -1152,37 +1369,80 @@
 	return 0;
 }
 
-int smc_llc_srv_add_link(struct smc_link *link)
+static void smc_llc_send_req_add_link_response(struct smc_llc_qentry *qentry)
+{
+	qentry->msg.raw.hdr.flags |= SMC_LLC_FLAG_RESP;
+	smc_llc_init_msg_hdr(&qentry->msg.raw.hdr, qentry->link->lgr,
+			     sizeof(qentry->msg));
+	memset(&qentry->msg.raw.data, 0, sizeof(qentry->msg.raw.data));
+	smc_llc_send_message(qentry->link, &qentry->msg);
+}
+
+int smc_llc_srv_add_link(struct smc_link *link,
+			 struct smc_llc_qentry *req_qentry)
 {
 	enum smc_lgr_type lgr_new_t = SMC_LGR_SYMMETRIC;
 	struct smc_link_group *lgr = link->lgr;
 	struct smc_llc_msg_add_link *add_llc;
 	struct smc_llc_qentry *qentry = NULL;
-	struct smc_link *link_new;
-	struct smc_init_info ini;
+	bool send_req_add_link_resp = false;
+	struct smc_link *link_new = NULL;
+	struct smc_init_info *ini = NULL;
 	int lnk_idx, rc = 0;
 
+	if (req_qentry &&
+	    req_qentry->msg.raw.hdr.common.llc_type == SMC_LLC_REQ_ADD_LINK)
+		send_req_add_link_resp = true;
+
+	ini = kzalloc(sizeof(*ini), GFP_KERNEL);
+	if (!ini) {
+		rc = -ENOMEM;
+		goto out;
+	}
+
 	/* ignore client add link recommendation, start new flow */
-	ini.vlan_id = lgr->vlan_id;
-	smc_pnet_find_alt_roce(lgr, &ini, link->smcibdev);
-	if (!ini.ib_dev) {
+	ini->vlan_id = lgr->vlan_id;
+	if (lgr->smc_version == SMC_V2) {
+		ini->check_smcrv2 = true;
+		ini->smcrv2.saddr = lgr->saddr;
+		if (send_req_add_link_resp) {
+			struct smc_llc_msg_req_add_link_v2 *req_add =
+				&req_qentry->msg.req_add_link;
+
+			ini->smcrv2.daddr = smc_ib_gid_to_ipv4(req_add->gid[0]);
+		}
+	}
+	smc_pnet_find_alt_roce(lgr, ini, link->smcibdev);
+	if (lgr->smc_version == SMC_V2 && !ini->smcrv2.ib_dev_v2) {
+		lgr_new_t = SMC_LGR_ASYMMETRIC_LOCAL;
+		ini->smcrv2.ib_dev_v2 = link->smcibdev;
+		ini->smcrv2.ib_port_v2 = link->ibport;
+	} else if (lgr->smc_version < SMC_V2 && !ini->ib_dev) {
 		lgr_new_t = SMC_LGR_ASYMMETRIC_LOCAL;
-		ini.ib_dev = link->smcibdev;
-		ini.ib_port = link->ibport;
+		ini->ib_dev = link->smcibdev;
+		ini->ib_port = link->ibport;
 	}
 	lnk_idx = smc_llc_alloc_alt_link(lgr, lgr_new_t);
-	if (lnk_idx < 0)
-		return 0;
+	if (lnk_idx < 0) {
+		rc = 0;
+		goto out;
+	}
 
-	rc = smcr_link_init(lgr, &lgr->lnk[lnk_idx], lnk_idx, &ini);
+	rc = smcr_link_init(lgr, &lgr->lnk[lnk_idx], lnk_idx, ini);
 	if (rc)
-		return rc;
+		goto out;
 	link_new = &lgr->lnk[lnk_idx];
+
+	rc = smcr_buf_map_lgr(link_new);
+	if (rc)
+		goto out_err;
+
 	rc = smc_llc_send_add_link(link,
-				   link_new->smcibdev->mac[ini.ib_port - 1],
+				   link_new->smcibdev->mac[link_new->ibport-1],
 				   link_new->gid, link_new, SMC_LLC_REQ);
 	if (rc)
 		goto out_err;
+	send_req_add_link_resp = false;
 	/* receive ADD LINK response over the RoCE fabric */
 	qentry = smc_llc_wait(lgr, link, SMC_LLC_WAIT_TIME, SMC_LLC_ADD_LINK);
 	if (!qentry) {
@@ -1197,7 +1457,8 @@
 	}
 	if (lgr->type == SMC_LGR_SINGLE &&
 	    (!memcmp(add_llc->sender_gid, link->peer_gid, SMC_GID_SIZE) &&
-	     !memcmp(add_llc->sender_mac, link->peer_mac, ETH_ALEN))) {
+	     (lgr->smc_version == SMC_V2 ||
+	      !memcmp(add_llc->sender_mac, link->peer_mac, ETH_ALEN)))) {
 		lgr_new_t = SMC_LGR_ASYMMETRIC_PEER;
 	}
 	smc_llc_save_add_link_info(link_new, add_llc);
@@ -1206,39 +1467,49 @@
 	rc = smc_ib_ready_link(link_new);
 	if (rc)
 		goto out_err;
-	rc = smcr_buf_map_lgr(link_new);
-	if (rc)
-		goto out_err;
 	rc = smcr_buf_reg_lgr(link_new);
 	if (rc)
 		goto out_err;
-	rc = smc_llc_srv_rkey_exchange(link, link_new);
-	if (rc)
-		goto out_err;
+	if (lgr->smc_version == SMC_V2) {
+		smc_llc_save_add_link_rkeys(link, link_new);
+	} else {
+		rc = smc_llc_srv_rkey_exchange(link, link_new);
+		if (rc)
+			goto out_err;
+	}
 	rc = smc_llc_srv_conf_link(link, link_new, lgr_new_t);
 	if (rc)
 		goto out_err;
+	kfree(ini);
 	return 0;
 out_err:
-	link_new->state = SMC_LNK_INACTIVE;
-	smcr_link_clear(link_new, false);
+	if (link_new) {
+		link_new->state = SMC_LNK_INACTIVE;
+		smcr_link_clear(link_new, false);
+	}
+out:
+	kfree(ini);
+	if (send_req_add_link_resp)
+		smc_llc_send_req_add_link_response(req_qentry);
 	return rc;
 }
 
 static void smc_llc_process_srv_add_link(struct smc_link_group *lgr)
 {
 	struct smc_link *link = lgr->llc_flow_lcl.qentry->link;
+	struct smc_llc_qentry *qentry;
 	int rc;
 
-	smc_llc_flow_qentry_del(&lgr->llc_flow_lcl);
+	qentry = smc_llc_flow_qentry_clr(&lgr->llc_flow_lcl);
 
 	mutex_lock(&lgr->llc_conf_mutex);
-	rc = smc_llc_srv_add_link(link);
+	rc = smc_llc_srv_add_link(link, qentry);
 	if (!rc && lgr->type == SMC_LGR_SYMMETRIC) {
 		/* delete any asymmetric link */
 		smc_llc_delete_asym_link(lgr);
 	}
 	mutex_unlock(&lgr->llc_conf_mutex);
+	kfree(qentry);
 }
 
 /* enqueue a local add_link req to trigger a new add_link flow */
@@ -1246,8 +1517,8 @@
 {
 	struct smc_llc_msg_add_link add_llc = {};
 
-	add_llc.hd.length = sizeof(add_llc);
-	add_llc.hd.common.type = SMC_LLC_ADD_LINK;
+	add_llc.hd.common.llc_type = SMC_LLC_ADD_LINK;
+	smc_llc_init_msg_hdr(&add_llc.hd, link->lgr, sizeof(add_llc));
 	/* no dev and port needed */
 	smc_llc_enqueue(link, (union smc_llc_msg *)&add_llc);
 }
@@ -1269,7 +1540,8 @@
 	else
 		smc_llc_process_srv_add_link(lgr);
 out:
-	smc_llc_flow_stop(lgr, &lgr->llc_flow_lcl);
+	if (lgr->llc_flow_lcl.type != SMC_LLC_FLOW_REQ_ADD_LINK)
+		smc_llc_flow_stop(lgr, &lgr->llc_flow_lcl);
 }
 
 /* enqueue a local del_link msg to trigger a new del_link flow,
@@ -1279,8 +1551,8 @@
 {
 	struct smc_llc_msg_del_link del_llc = {};
 
-	del_llc.hd.length = sizeof(del_llc);
-	del_llc.hd.common.type = SMC_LLC_DELETE_LINK;
+	del_llc.hd.common.llc_type = SMC_LLC_DELETE_LINK;
+	smc_llc_init_msg_hdr(&del_llc.hd, link->lgr, sizeof(del_llc));
 	del_llc.link_num = del_link_id;
 	del_llc.reason = htonl(SMC_LLC_DEL_LOST_PATH);
 	del_llc.hd.flags |= SMC_LLC_FLAG_DEL_LINK_ORDERLY;
@@ -1350,15 +1622,15 @@
 	struct smc_llc_msg_del_link delllc = {};
 	int i;
 
-	delllc.hd.common.type = SMC_LLC_DELETE_LINK;
-	delllc.hd.length = sizeof(delllc);
+	delllc.hd.common.llc_type = SMC_LLC_DELETE_LINK;
+	smc_llc_init_msg_hdr(&delllc.hd, lgr, sizeof(delllc));
 	if (ord)
 		delllc.hd.flags |= SMC_LLC_FLAG_DEL_LINK_ORDERLY;
 	delllc.hd.flags |= SMC_LLC_FLAG_DEL_LINK_ALL;
 	delllc.reason = htonl(rsn);
 
 	for (i = 0; i < SMC_LINKS_PER_LGR_MAX; i++) {
-		if (!smc_link_usable(&lgr->lnk[i]))
+		if (!smc_link_sendable(&lgr->lnk[i]))
 			continue;
 		if (!smc_llc_send_message_wait(&lgr->lnk[i], &delllc))
 			break;
@@ -1467,6 +1739,8 @@
 	link = qentry->link;
 
 	num_entries = llc->rtoken[0].num_rkeys;
+	if (num_entries > SMC_LLC_RKEYS_PER_MSG)
+		goto out_err;
 	/* first rkey entry is for receiving link */
 	rk_idx = smc_rtoken_add(link,
 				llc->rtoken[0].rmb_vaddr,
@@ -1485,6 +1759,7 @@
 	llc->hd.flags |= SMC_LLC_FLAG_RKEY_RETRY;
 out:
 	llc->hd.flags |= SMC_LLC_FLAG_RESP;
+	smc_llc_init_msg_hdr(&llc->hd, link->lgr, sizeof(*llc));
 	smc_llc_send_message(link, &qentry->msg);
 	smc_llc_flow_qentry_del(&lgr->llc_flow_rmt);
 }
@@ -1502,6 +1777,28 @@
 	llc = &qentry->msg.delete_rkey;
 	link = qentry->link;
 
+	if (lgr->smc_version == SMC_V2) {
+		struct smc_llc_msg_delete_rkey_v2 *llcv2;
+
+		memcpy(lgr->wr_rx_buf_v2, llc, sizeof(*llc));
+		llcv2 = (struct smc_llc_msg_delete_rkey_v2 *)lgr->wr_rx_buf_v2;
+		llcv2->num_inval_rkeys = 0;
+
+		max = min_t(u8, llcv2->num_rkeys, SMC_LLC_RKEYS_PER_MSG_V2);
+		for (i = 0; i < max; i++) {
+			if (smc_rtoken_delete(link, llcv2->rkey[i]))
+				llcv2->num_inval_rkeys++;
+		}
+		memset(&llc->rkey[0], 0, sizeof(llc->rkey));
+		memset(&llc->reserved2, 0, sizeof(llc->reserved2));
+		smc_llc_init_msg_hdr(&llc->hd, link->lgr, sizeof(*llc));
+		if (llcv2->num_inval_rkeys) {
+			llc->hd.flags |= SMC_LLC_FLAG_RKEY_NEG;
+			llc->err_mask = llcv2->num_inval_rkeys;
+		}
+		goto finish;
+	}
+
 	max = min_t(u8, llc->num_rkeys, SMC_LLC_DEL_RKEY_MAX);
 	for (i = 0; i < max; i++) {
 		if (smc_rtoken_delete(link, llc->rkey[i]))
@@ -1511,6 +1808,7 @@
 		llc->hd.flags |= SMC_LLC_FLAG_RKEY_NEG;
 		llc->err_mask = err_mask;
 	}
+finish:
 	llc->hd.flags |= SMC_LLC_FLAG_RESP;
 	smc_llc_send_message(link, &qentry->msg);
 	smc_llc_flow_qentry_del(&lgr->llc_flow_rmt);
@@ -1546,7 +1844,7 @@
 	if (!smc_link_usable(link))
 		goto out;
 
-	switch (llc->raw.hdr.common.type) {
+	switch (llc->raw.hdr.common.llc_type) {
 	case SMC_LLC_TEST_LINK:
 		llc->test_link.hd.flags |= SMC_LLC_FLAG_RESP;
 		smc_llc_send_message(link, llc);
@@ -1571,8 +1869,18 @@
 				smc_llc_flow_qentry_set(&lgr->llc_flow_lcl,
 							qentry);
 				wake_up(&lgr->llc_msg_waiter);
-			} else if (smc_llc_flow_start(&lgr->llc_flow_lcl,
-						      qentry)) {
+				return;
+			}
+			if (lgr->llc_flow_lcl.type ==
+					SMC_LLC_FLOW_REQ_ADD_LINK) {
+				/* server started add_link processing */
+				lgr->llc_flow_lcl.type = SMC_LLC_FLOW_ADD_LINK;
+				smc_llc_flow_qentry_set(&lgr->llc_flow_lcl,
+							qentry);
+				schedule_work(&lgr->llc_add_link_work);
+				return;
+			}
+			if (smc_llc_flow_start(&lgr->llc_flow_lcl, qentry)) {
 				schedule_work(&lgr->llc_add_link_work);
 			}
 		} else if (smc_llc_flow_start(&lgr->llc_flow_lcl, qentry)) {
@@ -1620,6 +1928,23 @@
 			smc_llc_flow_stop(lgr, &lgr->llc_flow_rmt);
 		}
 		return;
+	case SMC_LLC_REQ_ADD_LINK:
+		/* handle response here, smc_llc_flow_stop() cannot be called
+		 * in tasklet context
+		 */
+		if (lgr->role == SMC_CLNT &&
+		    lgr->llc_flow_lcl.type == SMC_LLC_FLOW_REQ_ADD_LINK &&
+		    (llc->raw.hdr.flags & SMC_LLC_FLAG_RESP)) {
+			smc_llc_flow_stop(link->lgr, &lgr->llc_flow_lcl);
+		} else if (lgr->role == SMC_SERV) {
+			if (smc_llc_flow_start(&lgr->llc_flow_lcl, qentry)) {
+				/* as smc server, handle client suggestion */
+				lgr->llc_flow_lcl.type = SMC_LLC_FLOW_ADD_LINK;
+				schedule_work(&lgr->llc_add_link_work);
+			}
+			return;
+		}
+		break;
 	default:
 		smc_llc_protocol_violation(lgr, llc->raw.hdr.common.type);
 		break;
@@ -1663,7 +1988,7 @@
 {
 	enum smc_llc_flowtype flowtype = link->lgr->llc_flow_lcl.type;
 	struct smc_llc_flow *flow = &link->lgr->llc_flow_lcl;
-	u8 llc_type = qentry->msg.raw.hdr.common.type;
+	u8 llc_type = qentry->msg.raw.hdr.common.llc_type;
 
 	switch (llc_type) {
 	case SMC_LLC_TEST_LINK:
@@ -1689,7 +2014,8 @@
 		/* not used because max links is 3 */
 		break;
 	default:
-		smc_llc_protocol_violation(link->lgr, llc_type);
+		smc_llc_protocol_violation(link->lgr,
+					   qentry->msg.raw.hdr.common.type);
 		break;
 	}
 	kfree(qentry);
@@ -1714,7 +2040,8 @@
 	memcpy(&qentry->msg, llc, sizeof(union smc_llc_msg));
 
 	/* process responses immediately */
-	if (llc->raw.hdr.flags & SMC_LLC_FLAG_RESP) {
+	if ((llc->raw.hdr.flags & SMC_LLC_FLAG_RESP) &&
+	    llc->raw.hdr.common.llc_type != SMC_LLC_REQ_ADD_LINK) {
 		smc_llc_rx_response(link, qentry);
 		return;
 	}
@@ -1734,8 +2061,13 @@
 
 	if (wc->byte_len < sizeof(*llc))
 		return; /* short message */
-	if (llc->raw.hdr.length != sizeof(*llc))
-		return; /* invalid message */
+	if (!llc->raw.hdr.common.llc_version) {
+		if (llc->raw.hdr.length != sizeof(*llc))
+			return; /* invalid message */
+	} else {
+		if (llc->raw.hdr.length_v2 < sizeof(*llc))
+			return; /* invalid message */
+	}
 
 	smc_llc_enqueue(link, llc);
 }
@@ -1787,7 +2119,7 @@
 	init_waitqueue_head(&lgr->llc_flow_waiter);
 	init_waitqueue_head(&lgr->llc_msg_waiter);
 	mutex_init(&lgr->llc_conf_mutex);
-	lgr->llc_testlink_time = net->ipv4.sysctl_tcp_keepalive_time;
+	lgr->llc_testlink_time = READ_ONCE(net->ipv4.sysctl_tcp_keepalive_time);
 }
 
 /* called after lgr was removed from lgr_list */
@@ -1954,6 +2286,35 @@
 		.handler	= smc_llc_rx_handler,
 		.type		= SMC_LLC_DELETE_RKEY
 	},
+	/* V2 types */
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_CONFIRM_LINK_V2
+	},
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_TEST_LINK_V2
+	},
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_ADD_LINK_V2
+	},
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_DELETE_LINK_V2
+	},
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_REQ_ADD_LINK_V2
+	},
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_CONFIRM_RKEY_V2
+	},
+	{
+		.handler	= smc_llc_rx_handler,
+		.type		= SMC_LLC_DELETE_RKEY_V2
+	},
 	{
 		.handler	= NULL,
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_llc.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_llc.h
@@ -30,10 +30,19 @@
 	SMC_LLC_ADD_LINK		= 0x02,
 	SMC_LLC_ADD_LINK_CONT		= 0x03,
 	SMC_LLC_DELETE_LINK		= 0x04,
+	SMC_LLC_REQ_ADD_LINK		= 0x05,
 	SMC_LLC_CONFIRM_RKEY		= 0x06,
 	SMC_LLC_TEST_LINK		= 0x07,
 	SMC_LLC_CONFIRM_RKEY_CONT	= 0x08,
 	SMC_LLC_DELETE_RKEY		= 0x09,
+	/* V2 types */
+	SMC_LLC_CONFIRM_LINK_V2		= 0x21,
+	SMC_LLC_ADD_LINK_V2		= 0x22,
+	SMC_LLC_DELETE_LINK_V2		= 0x24,
+	SMC_LLC_REQ_ADD_LINK_V2		= 0x25,
+	SMC_LLC_CONFIRM_RKEY_V2		= 0x26,
+	SMC_LLC_TEST_LINK_V2		= 0x27,
+	SMC_LLC_DELETE_RKEY_V2		= 0x29,
 };
 
 #define smc_link_downing(state) \
@@ -102,7 +111,8 @@
 void smc_llc_send_link_delete_all(struct smc_link_group *lgr, bool ord,
 				  u32 rsn);
 int smc_llc_cli_add_link(struct smc_link *link, struct smc_llc_qentry *qentry);
-int smc_llc_srv_add_link(struct smc_link *link);
+int smc_llc_srv_add_link(struct smc_link *link,
+			 struct smc_llc_qentry *req_qentry);
 void smc_llc_add_link_local(struct smc_link *link);
 int smc_llc_init(void) __init;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_netlink.c
@@ -19,11 +19,19 @@
 #include "smc_core.h"
 #include "smc_ism.h"
 #include "smc_ib.h"
+#include "smc_clc.h"
 #include "smc_stats.h"
 #include "smc_netlink.h"
 
-#define SMC_CMD_MAX_ATTR 1
+const struct nla_policy
+smc_gen_ueid_policy[SMC_NLA_EID_TABLE_MAX + 1] = {
+	[SMC_NLA_EID_TABLE_UNSPEC]	= { .type = NLA_UNSPEC },
+	[SMC_NLA_EID_TABLE_ENTRY]	= { .type = NLA_STRING,
+					    .len = SMC_MAX_EID_LEN,
+					  },
+};
 
+#define SMC_CMD_MAX_ATTR 1
 /* SMC_GENL generic netlink operation definition */
 static const struct genl_ops smc_gen_nl_ops[] = {
 	{
@@ -66,6 +74,43 @@
 		/* can be retrieved by unprivileged users */
 		.dumpit = smc_nl_get_fback_stats,
 	},
+	{
+		.cmd = SMC_NETLINK_DUMP_UEID,
+		/* can be retrieved by unprivileged users */
+		.dumpit = smc_nl_dump_ueid,
+	},
+	{
+		.cmd = SMC_NETLINK_ADD_UEID,
+		.flags = GENL_ADMIN_PERM,
+		.doit = smc_nl_add_ueid,
+		.policy = smc_gen_ueid_policy,
+	},
+	{
+		.cmd = SMC_NETLINK_REMOVE_UEID,
+		.flags = GENL_ADMIN_PERM,
+		.doit = smc_nl_remove_ueid,
+		.policy = smc_gen_ueid_policy,
+	},
+	{
+		.cmd = SMC_NETLINK_FLUSH_UEID,
+		.flags = GENL_ADMIN_PERM,
+		.doit = smc_nl_flush_ueid,
+	},
+	{
+		.cmd = SMC_NETLINK_DUMP_SEID,
+		/* can be retrieved by unprivileged users */
+		.dumpit = smc_nl_dump_seid,
+	},
+	{
+		.cmd = SMC_NETLINK_ENABLE_SEID,
+		.flags = GENL_ADMIN_PERM,
+		.doit = smc_nl_enable_seid,
+	},
+	{
+		.cmd = SMC_NETLINK_DISABLE_SEID,
+		.flags = GENL_ADMIN_PERM,
+		.doit = smc_nl_disable_seid,
+	},
 };
 
 static const struct nla_policy smc_gen_nl_policy[2] = {
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_netlink.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_netlink.h
@@ -17,6 +17,8 @@
 
 extern struct genl_family smc_gen_nl_family;
 
+extern const struct nla_policy smc_gen_ueid_policy[];
+
 struct smc_nl_dmp_ctx {
 	int pos[3];
 };
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_pnet.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_pnet.c
@@ -112,7 +112,7 @@
 	pnettable = &sn->pnettable;
 
 	/* remove table entry */
-	write_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry_safe(pnetelem, tmp_pe, &pnettable->pnetlist,
 				 list) {
 		if (!pnet_name ||
@@ -130,7 +130,7 @@
 			rc = 0;
 		}
 	}
-	write_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 
 	/* if this is not the initial namespace, stop here */
 	if (net != &init_net)
@@ -191,7 +191,7 @@
 	sn = net_generic(net, smc_net_id);
 	pnettable = &sn->pnettable;
 
-	write_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry_safe(pnetelem, tmp_pe, &pnettable->pnetlist, list) {
 		if (pnetelem->type == SMC_PNET_ETH && !pnetelem->ndev &&
 		    !strncmp(pnetelem->eth_name, ndev->name, IFNAMSIZ)) {
@@ -205,7 +205,7 @@
 			break;
 		}
 	}
-	write_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 	return rc;
 }
 
@@ -223,7 +223,7 @@
 	sn = net_generic(net, smc_net_id);
 	pnettable = &sn->pnettable;
 
-	write_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry_safe(pnetelem, tmp_pe, &pnettable->pnetlist, list) {
 		if (pnetelem->type == SMC_PNET_ETH && pnetelem->ndev == ndev) {
 			dev_put(pnetelem->ndev);
@@ -236,7 +236,7 @@
 			break;
 		}
 	}
-	write_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 	return rc;
 }
 
@@ -310,8 +310,9 @@
 	list_for_each_entry(ibdev, &smc_ib_devices.list, list) {
 		if (!strncmp(ibdev->ibdev->name, ib_name,
 			     sizeof(ibdev->ibdev->name)) ||
-		    !strncmp(dev_name(ibdev->ibdev->dev.parent), ib_name,
-			     IB_DEVICE_NAME_MAX - 1)) {
+		    (ibdev->ibdev->dev.parent &&
+		     !strncmp(dev_name(ibdev->ibdev->dev.parent), ib_name,
+			     IB_DEVICE_NAME_MAX - 1))) {
 			goto out;
 		}
 	}
@@ -371,7 +372,7 @@
 
 	rc = -EEXIST;
 	new_netdev = true;
-	write_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry(tmp_pe, &pnettable->pnetlist, list) {
 		if (tmp_pe->type == SMC_PNET_ETH &&
 		    !strncmp(tmp_pe->eth_name, eth_name, IFNAMSIZ)) {
@@ -381,9 +382,9 @@
 	}
 	if (new_netdev) {
 		list_add_tail(&new_pe->list, &pnettable->pnetlist);
-		write_unlock(&pnettable->lock);
+		mutex_unlock(&pnettable->lock);
 	} else {
-		write_unlock(&pnettable->lock);
+		mutex_unlock(&pnettable->lock);
 		kfree(new_pe);
 		goto out_put;
 	}
@@ -444,7 +445,7 @@
 	new_pe->ib_port = ib_port;
 
 	new_ibdev = true;
-	write_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry(tmp_pe, &pnettable->pnetlist, list) {
 		if (tmp_pe->type == SMC_PNET_IB &&
 		    !strncmp(tmp_pe->ib_name, ib_name, IB_DEVICE_NAME_MAX)) {
@@ -454,9 +455,9 @@
 	}
 	if (new_ibdev) {
 		list_add_tail(&new_pe->list, &pnettable->pnetlist);
-		write_unlock(&pnettable->lock);
+		mutex_unlock(&pnettable->lock);
 	} else {
-		write_unlock(&pnettable->lock);
+		mutex_unlock(&pnettable->lock);
 		kfree(new_pe);
 	}
 	return (new_ibdev) ? 0 : -EEXIST;
@@ -601,7 +602,7 @@
 	pnettable = &sn->pnettable;
 
 	/* dump pnettable entries */
-	read_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry(pnetelem, &pnettable->pnetlist, list) {
 		if (pnetid && !smc_pnet_match(pnetelem->pnet_name, pnetid))
 			continue;
@@ -616,7 +617,7 @@
 			break;
 		}
 	}
-	read_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 	return idx;
 }
 
@@ -742,7 +743,7 @@
 
 	write_lock(&sn->pnetids_ndev.lock);
 	list_for_each_entry(pi, &sn->pnetids_ndev.list, list) {
-		if (smc_pnet_match(pnetid, pe->pnetid)) {
+		if (smc_pnet_match(pnetid, pi->pnetid)) {
 			refcount_inc(&pi->refcnt);
 			kfree(pe);
 			goto unlock;
@@ -795,6 +796,16 @@
 	u8 ndev_pnetid[SMC_MAX_PNETID_LEN];
 	struct net_device *dev;
 
+	/* Newly created netns do not have devices.
+	 * Do not even acquire rtnl.
+	 */
+	if (list_empty(&net->dev_base_head))
+		return;
+
+	/* Note: This might not be needed, because smc_pnet_netdev_event()
+	 * is also calling smc_pnet_add_base_pnetid() when handling
+	 * NETDEV_UP event.
+	 */
 	rtnl_lock();
 	for_each_netdev(net, dev)
 		smc_pnet_add_base_pnetid(net, dev, ndev_pnetid);
@@ -860,7 +871,7 @@
 	struct smc_pnetids_ndev *pnetids_ndev = &sn->pnetids_ndev;
 
 	INIT_LIST_HEAD(&pnettable->pnetlist);
-	rwlock_init(&pnettable->lock);
+	mutex_init(&pnettable->lock);
 	INIT_LIST_HEAD(&pnetids_ndev->list);
 	rwlock_init(&pnetids_ndev->lock);
 
@@ -940,7 +951,7 @@
 	sn = net_generic(net, smc_net_id);
 	pnettable = &sn->pnettable;
 
-	read_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry(pnetelem, &pnettable->pnetlist, list) {
 		if (pnetelem->type == SMC_PNET_ETH && ndev == pnetelem->ndev) {
 			/* get pnetid of netdev device */
@@ -949,10 +960,30 @@
 			break;
 		}
 	}
-	read_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 	return rc;
 }
 
+static int smc_pnet_determine_gid(struct smc_ib_device *ibdev, int i,
+				  struct smc_init_info *ini)
+{
+	if (!ini->check_smcrv2 &&
+	    !smc_ib_determine_gid(ibdev, i, ini->vlan_id, ini->ib_gid, NULL,
+				  NULL)) {
+		ini->ib_dev = ibdev;
+		ini->ib_port = i;
+		return 0;
+	}
+	if (ini->check_smcrv2 &&
+	    !smc_ib_determine_gid(ibdev, i, ini->vlan_id, ini->smcrv2.ib_gid_v2,
+				  NULL, &ini->smcrv2)) {
+		ini->smcrv2.ib_dev_v2 = ibdev;
+		ini->smcrv2.ib_port_v2 = i;
+		return 0;
+	}
+	return -ENODEV;
+}
+
 /* find a roce device for the given pnetid */
 static void _smc_pnet_find_roce_by_pnetid(u8 *pnet_id,
 					  struct smc_init_info *ini,
@@ -961,7 +992,6 @@
 	struct smc_ib_device *ibdev;
 	int i;
 
-	ini->ib_dev = NULL;
 	mutex_lock(&smc_ib_devices.mutex);
 	list_for_each_entry(ibdev, &smc_ib_devices.list, list) {
 		if (ibdev == known_dev)
@@ -971,12 +1001,9 @@
 				continue;
 			if (smc_pnet_match(ibdev->pnetid[i - 1], pnet_id) &&
 			    smc_ib_port_active(ibdev, i) &&
-			    !test_bit(i - 1, ibdev->ports_going_away) &&
-			    !smc_ib_determine_gid(ibdev, i, ini->vlan_id,
-						  ini->ib_gid, NULL)) {
-				ini->ib_dev = ibdev;
-				ini->ib_port = i;
-				goto out;
+			    !test_bit(i - 1, ibdev->ports_going_away)) {
+				if (!smc_pnet_determine_gid(ibdev, i, ini))
+					goto out;
 			}
 		}
 	}
@@ -1016,12 +1043,9 @@
 			dev_put(ndev);
 			if (netdev == ndev &&
 			    smc_ib_port_active(ibdev, i) &&
-			    !test_bit(i - 1, ibdev->ports_going_away) &&
-			    !smc_ib_determine_gid(ibdev, i, ini->vlan_id,
-						  ini->ib_gid, NULL)) {
-				ini->ib_dev = ibdev;
-				ini->ib_port = i;
-				break;
+			    !test_bit(i - 1, ibdev->ports_going_away)) {
+				if (!smc_pnet_determine_gid(ibdev, i, ini))
+					break;
 			}
 		}
 	}
@@ -1083,8 +1107,6 @@
 {
 	struct dst_entry *dst = sk_dst_get(sk);
 
-	ini->ib_dev = NULL;
-	ini->ib_port = 0;
 	if (!dst)
 		goto out;
 	if (!dst->dev)
@@ -1130,7 +1152,7 @@
 	sn = net_generic(&init_net, smc_net_id);
 	pnettable = &sn->pnettable;
 
-	read_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry(tmp_pe, &pnettable->pnetlist, list) {
 		if (tmp_pe->type == SMC_PNET_IB &&
 		    !strncmp(tmp_pe->ib_name, ib_name, IB_DEVICE_NAME_MAX) &&
@@ -1140,7 +1162,7 @@
 			break;
 		}
 	}
-	read_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 
 	return rc;
 }
@@ -1159,7 +1181,7 @@
 	sn = net_generic(&init_net, smc_net_id);
 	pnettable = &sn->pnettable;
 
-	read_lock(&pnettable->lock);
+	mutex_lock(&pnettable->lock);
 	list_for_each_entry(tmp_pe, &pnettable->pnetlist, list) {
 		if (tmp_pe->type == SMC_PNET_IB &&
 		    !strncmp(tmp_pe->ib_name, ib_name, IB_DEVICE_NAME_MAX)) {
@@ -1168,7 +1190,7 @@
 			break;
 		}
 	}
-	read_unlock(&pnettable->lock);
+	mutex_unlock(&pnettable->lock);
 
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_pnet.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_pnet.h
@@ -29,7 +29,7 @@
  * @pnetlist: List of PNETIDs
  */
 struct smc_pnettable {
-	rwlock_t lock;
+	struct mutex lock;
 	struct list_head pnetlist;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_rx.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_rx.c
@@ -175,22 +175,23 @@
 	return bytes;
 }
 
-static int smc_rx_data_available_and_no_splice_pend(struct smc_connection *conn)
+static int smc_rx_data_available_and_no_splice_pend(struct smc_connection *conn, size_t peeked)
 {
-	return atomic_read(&conn->bytes_to_rcv) &&
+	return smc_rx_data_available(conn, peeked) &&
 	       !atomic_read(&conn->splice_pending);
 }
 
 /* blocks rcvbuf consumer until >=len bytes available or timeout or interrupted
  *   @smc    smc socket
  *   @timeo  pointer to max seconds to wait, pointer to value 0 for no timeout
+ *   @peeked  number of bytes already peeked
  *   @fcrit  add'l criterion to evaluate as function pointer
  * Returns:
  * 1 if at least 1 byte available in rcvbuf or if socket error/shutdown.
  * 0 otherwise (nothing in rcvbuf nor timeout, e.g. interrupted).
  */
-int smc_rx_wait(struct smc_sock *smc, long *timeo,
-		int (*fcrit)(struct smc_connection *conn))
+int smc_rx_wait(struct smc_sock *smc, long *timeo, size_t peeked,
+		int (*fcrit)(struct smc_connection *conn, size_t baseline))
 {
 	DEFINE_WAIT_FUNC(wait, woken_wake_function);
 	struct smc_connection *conn = &smc->conn;
@@ -199,16 +200,16 @@
 	struct sock *sk = &smc->sk;
 	int rc;
 
-	if (fcrit(conn))
+	if (fcrit(conn, peeked))
 		return 1;
 	sk_set_bit(SOCKWQ_ASYNC_WAITDATA, sk);
 	add_wait_queue(sk_sleep(sk), &wait);
 	rc = sk_wait_event(sk, timeo,
-			   sk->sk_err ||
+			   READ_ONCE(sk->sk_err) ||
 			   cflags->peer_conn_abort ||
-			   sk->sk_shutdown & RCV_SHUTDOWN ||
+			   READ_ONCE(sk->sk_shutdown) & RCV_SHUTDOWN ||
 			   conn->killed ||
-			   fcrit(conn),
+			   fcrit(conn, peeked),
 			   &wait);
 	remove_wait_queue(sk_sleep(sk), &wait);
 	sk_clear_bit(SOCKWQ_ASYNC_WAITDATA, sk);
@@ -259,11 +260,11 @@
 	return -EAGAIN;
 }
 
-static bool smc_rx_recvmsg_data_available(struct smc_sock *smc)
+static bool smc_rx_recvmsg_data_available(struct smc_sock *smc, size_t peeked)
 {
 	struct smc_connection *conn = &smc->conn;
 
-	if (smc_rx_data_available(conn))
+	if (smc_rx_data_available(conn, peeked))
 		return true;
 	else if (conn->urg_state == SMC_URG_VALID)
 		/* we received a single urgent Byte - skip */
@@ -281,10 +282,10 @@
 int smc_rx_recvmsg(struct smc_sock *smc, struct msghdr *msg,
 		   struct pipe_inode_info *pipe, size_t len, int flags)
 {
-	size_t copylen, read_done = 0, read_remaining = len;
+	size_t copylen, read_done = 0, read_remaining = len, peeked_bytes = 0;
 	size_t chunk_len, chunk_off, chunk_len_sum;
 	struct smc_connection *conn = &smc->conn;
-	int (*func)(struct smc_connection *conn);
+	int (*func)(struct smc_connection *conn, size_t baseline);
 	union smc_host_cursor cons;
 	int readable, chunk;
 	char *rcvbuf_base;
@@ -321,14 +322,14 @@
 		if (conn->killed)
 			break;
 
-		if (smc_rx_recvmsg_data_available(smc))
+		if (smc_rx_recvmsg_data_available(smc, peeked_bytes))
 			goto copy;
 
 		if (sk->sk_shutdown & RCV_SHUTDOWN) {
 			/* smc_cdc_msg_recv_action() could have run after
 			 * above smc_rx_recvmsg_data_available()
 			 */
-			if (smc_rx_recvmsg_data_available(smc))
+			if (smc_rx_recvmsg_data_available(smc, peeked_bytes))
 				goto copy;
 			break;
 		}
@@ -354,34 +355,36 @@
 				}
 				break;
 			}
+			if (!timeo)
+				return -EAGAIN;
 			if (signal_pending(current)) {
 				read_done = sock_intr_errno(timeo);
 				break;
 			}
-			if (!timeo)
-				return -EAGAIN;
 		}
 
-		if (!smc_rx_data_available(conn)) {
-			smc_rx_wait(smc, &timeo, smc_rx_data_available);
+		if (!smc_rx_data_available(conn, peeked_bytes)) {
+			smc_rx_wait(smc, &timeo, peeked_bytes, smc_rx_data_available);
 			continue;
 		}
 
 copy:
 		/* initialize variables for 1st iteration of subsequent loop */
 		/* could be just 1 byte, even after waiting on data above */
-		readable = atomic_read(&conn->bytes_to_rcv);
+		readable = smc_rx_data_available(conn, peeked_bytes);
 		splbytes = atomic_read(&conn->splice_pending);
 		if (!readable || (msg && splbytes)) {
 			if (splbytes)
 				func = smc_rx_data_available_and_no_splice_pend;
 			else
 				func = smc_rx_data_available;
-			smc_rx_wait(smc, &timeo, func);
+			smc_rx_wait(smc, &timeo, peeked_bytes, func);
 			continue;
 		}
 
 		smc_curs_copy(&cons, &conn->local_tx_ctrl.cons, conn);
+		if ((flags & MSG_PEEK) && peeked_bytes)
+			smc_curs_add(conn->rmb_desc->len, &cons, peeked_bytes);
 		/* subsequent splice() calls pick up where previous left */
 		if (splbytes)
 			smc_curs_add(conn->rmb_desc->len, &cons, splbytes);
@@ -418,6 +421,8 @@
 			}
 			read_remaining -= chunk_len;
 			read_done += chunk_len;
+			if (flags & MSG_PEEK)
+				peeked_bytes += chunk_len;
 
 			if (chunk_len_sum == copylen)
 				break; /* either on 1st or 2nd iteration */
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_rx.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_rx.h
@@ -21,11 +21,11 @@
 
 int smc_rx_recvmsg(struct smc_sock *smc, struct msghdr *msg,
 		   struct pipe_inode_info *pipe, size_t len, int flags);
-int smc_rx_wait(struct smc_sock *smc, long *timeo,
-		int (*fcrit)(struct smc_connection *conn));
-static inline int smc_rx_data_available(struct smc_connection *conn)
+int smc_rx_wait(struct smc_sock *smc, long *timeo, size_t peeked,
+		int (*fcrit)(struct smc_connection *conn, size_t baseline));
+static inline int smc_rx_data_available(struct smc_connection *conn, size_t peeked)
 {
-	return atomic_read(&conn->bytes_to_rcv);
+	return atomic_read(&conn->bytes_to_rcv) - peeked;
 }
 
 #endif /* SMC_RX_H */
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_stats.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_stats.h
@@ -93,13 +93,14 @@
 	typeof(_smc_stats) stats = (_smc_stats); \
 	typeof(_tech) t = (_tech); \
 	typeof(_len) l = (_len); \
-	int _pos = fls64((l) >> 13); \
+	int _pos; \
 	typeof(_rc) r = (_rc); \
 	int m = SMC_BUF_MAX - 1; \
 	this_cpu_inc((*stats).smc[t].key ## _cnt); \
-	if (r <= 0) \
+	if (r <= 0 || l <= 0) \
 		break; \
-	_pos = (_pos < m) ? ((l == 1 << (_pos + 12)) ? _pos - 1 : _pos) : m; \
+	_pos = fls64((l - 1) >> 13); \
+	_pos = (_pos <= m) ? _pos : m; \
 	this_cpu_inc((*stats).smc[t].key ## _pd.buf[_pos]); \
 	this_cpu_add((*stats).smc[t].key ## _bytes, r); \
 } \
@@ -139,9 +140,12 @@
 do { \
 	typeof(_len) _l = (_len); \
 	typeof(_tech) t = (_tech); \
-	int _pos = fls((_l) >> 13); \
+	int _pos; \
 	int m = SMC_BUF_MAX - 1; \
-	_pos = (_pos < m) ? ((_l == 1 << (_pos + 12)) ? _pos - 1 : _pos) : m; \
+	if (_l <= 0) \
+		break; \
+	_pos = fls((_l - 1) >> 13); \
+	_pos = (_pos <= m) ? _pos : m; \
 	this_cpu_inc((*(_smc_stats)).smc[t].k ## _rmbsize.buf[_pos]); \
 } \
 while (0)
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_tx.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_tx.c
@@ -113,8 +113,8 @@
 			break; /* at least 1 byte of free & no urgent data */
 		set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
 		sk_wait_event(sk, &timeo,
-			      sk->sk_err ||
-			      (sk->sk_shutdown & SEND_SHUTDOWN) ||
+			      READ_ONCE(sk->sk_err) ||
+			      (READ_ONCE(sk->sk_shutdown) & SEND_SHUTDOWN) ||
 			      smc_cdc_rxed_any_close(conn) ||
 			      (atomic_read(&conn->sndbuf_space) &&
 			       !conn->urg_tx_pend),
@@ -594,27 +594,32 @@
 	return rc;
 }
 
-/* Wakeup sndbuf consumers from process context
- * since there is more data to transmit
- */
-void smc_tx_work(struct work_struct *work)
+void smc_tx_pending(struct smc_connection *conn)
 {
-	struct smc_connection *conn = container_of(to_delayed_work(work),
-						   struct smc_connection,
-						   tx_work);
 	struct smc_sock *smc = container_of(conn, struct smc_sock, conn);
 	int rc;
 
-	lock_sock(&smc->sk);
 	if (smc->sk.sk_err)
-		goto out;
+		return;
 
 	rc = smc_tx_sndbuf_nonempty(conn);
 	if (!rc && conn->local_rx_ctrl.prod_flags.write_blocked &&
 	    !atomic_read(&conn->bytes_to_rcv))
 		conn->local_rx_ctrl.prod_flags.write_blocked = 0;
+}
+
+/* Wakeup sndbuf consumers from process context
+ * since there is more data to transmit
+ */
+void smc_tx_work(struct work_struct *work)
+{
+	struct smc_connection *conn = container_of(to_delayed_work(work),
+						   struct smc_connection,
+						   tx_work);
+	struct smc_sock *smc = container_of(conn, struct smc_sock, conn);
 
-out:
+	lock_sock(&smc->sk);
+	smc_tx_pending(conn);
 	release_sock(&smc->sk);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_tx.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_tx.h
@@ -27,6 +27,7 @@
 	return smc_curs_diff(conn->sndbuf_desc->len, &sent, &prep);
 }
 
+void smc_tx_pending(struct smc_connection *conn);
 void smc_tx_work(struct work_struct *work);
 void smc_tx_init(struct smc_sock *smc);
 int smc_tx_sendmsg(struct smc_sock *smc, struct msghdr *msg, size_t len);
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_wr.c
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_wr.c
@@ -62,13 +62,9 @@
 }
 
 /* wait till all pending tx work requests on the given link are completed */
-int smc_wr_tx_wait_no_pending_sends(struct smc_link *link)
+void smc_wr_tx_wait_no_pending_sends(struct smc_link *link)
 {
-	if (wait_event_timeout(link->wr_tx_wait, !smc_wr_is_tx_pend(link),
-			       SMC_WR_TX_WAIT_PENDING_TIME))
-		return 0;
-	else /* timeout */
-		return -EPIPE;
+	wait_event(link->wr_tx_wait, !smc_wr_is_tx_pend(link));
 }
 
 static inline int smc_wr_tx_find_pending_index(struct smc_link *link, u64 wr_id)
@@ -87,7 +83,6 @@
 	struct smc_wr_tx_pend pnd_snd;
 	struct smc_link *link;
 	u32 pnd_snd_idx;
-	int i;
 
 	link = wc->qp->qp_context;
 
@@ -101,27 +96,38 @@
 	}
 
 	pnd_snd_idx = smc_wr_tx_find_pending_index(link, wc->wr_id);
-	if (pnd_snd_idx == link->wr_tx_cnt)
-		return;
-	link->wr_tx_pends[pnd_snd_idx].wc_status = wc->status;
-	if (link->wr_tx_pends[pnd_snd_idx].compl_requested)
-		complete(&link->wr_tx_compl[pnd_snd_idx]);
-	memcpy(&pnd_snd, &link->wr_tx_pends[pnd_snd_idx], sizeof(pnd_snd));
-	/* clear the full struct smc_wr_tx_pend including .priv */
-	memset(&link->wr_tx_pends[pnd_snd_idx], 0,
-	       sizeof(link->wr_tx_pends[pnd_snd_idx]));
-	memset(&link->wr_tx_bufs[pnd_snd_idx], 0,
-	       sizeof(link->wr_tx_bufs[pnd_snd_idx]));
-	if (!test_and_clear_bit(pnd_snd_idx, link->wr_tx_mask))
-		return;
+	if (pnd_snd_idx == link->wr_tx_cnt) {
+		if (link->lgr->smc_version != SMC_V2 ||
+		    link->wr_tx_v2_pend->wr_id != wc->wr_id)
+			return;
+		link->wr_tx_v2_pend->wc_status = wc->status;
+		memcpy(&pnd_snd, link->wr_tx_v2_pend, sizeof(pnd_snd));
+		/* clear the full struct smc_wr_tx_pend including .priv */
+		memset(link->wr_tx_v2_pend, 0,
+		       sizeof(*link->wr_tx_v2_pend));
+		memset(link->lgr->wr_tx_buf_v2, 0,
+		       sizeof(*link->lgr->wr_tx_buf_v2));
+	} else {
+		link->wr_tx_pends[pnd_snd_idx].wc_status = wc->status;
+		if (link->wr_tx_pends[pnd_snd_idx].compl_requested)
+			complete(&link->wr_tx_compl[pnd_snd_idx]);
+		memcpy(&pnd_snd, &link->wr_tx_pends[pnd_snd_idx],
+		       sizeof(pnd_snd));
+		/* clear the full struct smc_wr_tx_pend including .priv */
+		memset(&link->wr_tx_pends[pnd_snd_idx], 0,
+		       sizeof(link->wr_tx_pends[pnd_snd_idx]));
+		memset(&link->wr_tx_bufs[pnd_snd_idx], 0,
+		       sizeof(link->wr_tx_bufs[pnd_snd_idx]));
+		if (!test_and_clear_bit(pnd_snd_idx, link->wr_tx_mask))
+			return;
+	}
+
 	if (wc->status) {
-		for_each_set_bit(i, link->wr_tx_mask, link->wr_tx_cnt) {
-			/* clear full struct smc_wr_tx_pend including .priv */
-			memset(&link->wr_tx_pends[i], 0,
-			       sizeof(link->wr_tx_pends[i]));
-			memset(&link->wr_tx_bufs[i], 0,
-			       sizeof(link->wr_tx_bufs[i]));
-			clear_bit(i, link->wr_tx_mask);
+		if (link->lgr->smc_version == SMC_V2) {
+			memset(link->wr_tx_v2_pend, 0,
+			       sizeof(*link->wr_tx_v2_pend));
+			memset(link->lgr->wr_tx_buf_v2, 0,
+			       sizeof(*link->lgr->wr_tx_buf_v2));
 		}
 		/* terminate link */
 		smcr_link_down_cond_sched(link);
@@ -169,7 +175,7 @@
 static inline int smc_wr_tx_get_free_slot_index(struct smc_link *link, u32 *idx)
 {
 	*idx = link->wr_tx_cnt;
-	if (!smc_link_usable(link))
+	if (!smc_link_sendable(link))
 		return -ENOLINK;
 	for_each_clear_bit(*idx, link->wr_tx_mask, link->wr_tx_cnt) {
 		if (!test_and_set_bit(*idx, link->wr_tx_mask))
@@ -212,7 +218,7 @@
 	} else {
 		rc = wait_event_interruptible_timeout(
 			link->wr_tx_wait,
-			!smc_link_usable(link) ||
+			!smc_link_sendable(link) ||
 			lgr->terminating ||
 			(smc_wr_tx_get_free_slot_index(link, &idx) != -EBUSY),
 			SMC_WR_TX_WAIT_FREE_SLOT_TIME);
@@ -239,6 +245,33 @@
 	return 0;
 }
 
+int smc_wr_tx_get_v2_slot(struct smc_link *link,
+			  smc_wr_tx_handler handler,
+			  struct smc_wr_v2_buf **wr_buf,
+			  struct smc_wr_tx_pend_priv **wr_pend_priv)
+{
+	struct smc_wr_tx_pend *wr_pend;
+	struct ib_send_wr *wr_ib;
+	u64 wr_id;
+
+	if (link->wr_tx_v2_pend->idx == link->wr_tx_cnt)
+		return -EBUSY;
+
+	*wr_buf = NULL;
+	*wr_pend_priv = NULL;
+	wr_id = smc_wr_tx_get_next_wr_id(link);
+	wr_pend = link->wr_tx_v2_pend;
+	wr_pend->wr_id = wr_id;
+	wr_pend->handler = handler;
+	wr_pend->link = link;
+	wr_pend->idx = link->wr_tx_cnt;
+	wr_ib = link->wr_tx_v2_ib;
+	wr_ib->wr_id = wr_id;
+	*wr_buf = link->lgr->wr_tx_buf_v2;
+	*wr_pend_priv = &wr_pend->priv;
+	return 0;
+}
+
 int smc_wr_tx_put_slot(struct smc_link *link,
 		       struct smc_wr_tx_pend_priv *wr_pend_priv)
 {
@@ -256,6 +289,14 @@
 		test_and_clear_bit(idx, link->wr_tx_mask);
 		wake_up(&link->wr_tx_wait);
 		return 1;
+	} else if (link->lgr->smc_version == SMC_V2 &&
+		   pend->idx == link->wr_tx_cnt) {
+		/* Large v2 buffer */
+		memset(&link->wr_tx_v2_pend, 0,
+		       sizeof(link->wr_tx_v2_pend));
+		memset(&link->lgr->wr_tx_buf_v2, 0,
+		       sizeof(link->lgr->wr_tx_buf_v2));
+		return 1;
 	}
 
 	return 0;
@@ -280,6 +321,22 @@
 	return rc;
 }
 
+int smc_wr_tx_v2_send(struct smc_link *link, struct smc_wr_tx_pend_priv *priv,
+		      int len)
+{
+	int rc;
+
+	link->wr_tx_v2_ib->sg_list[0].length = len;
+	ib_req_notify_cq(link->smcibdev->roce_cq_send,
+			 IB_CQ_NEXT_COMP | IB_CQ_REPORT_MISSED_EVENTS);
+	rc = ib_post_send(link->roce_qp, link->wr_tx_v2_ib, NULL);
+	if (rc) {
+		smc_wr_tx_put_slot(link, priv);
+		smcr_link_down_cond_sched(link);
+	}
+	return rc;
+}
+
 /* Send prepared WR slot via ib_post_send and wait for send completion
  * notification.
  * @priv: pointer to smc_wr_tx_pend_priv identifying prepared message buffer
@@ -288,18 +345,20 @@
 			unsigned long timeout)
 {
 	struct smc_wr_tx_pend *pend;
+	u32 pnd_idx;
 	int rc;
 
 	pend = container_of(priv, struct smc_wr_tx_pend, priv);
 	pend->compl_requested = 1;
-	init_completion(&link->wr_tx_compl[pend->idx]);
+	pnd_idx = pend->idx;
+	init_completion(&link->wr_tx_compl[pnd_idx]);
 
 	rc = smc_wr_tx_send(link, priv);
 	if (rc)
 		return rc;
 	/* wait for completion by smc_wr_tx_process_cqe() */
 	rc = wait_for_completion_interruptible_timeout(
-					&link->wr_tx_compl[pend->idx], timeout);
+					&link->wr_tx_compl[pnd_idx], timeout);
 	if (rc <= 0)
 		rc = -ENODATA;
 	if (rc > 0)
@@ -349,25 +408,6 @@
 	return rc;
 }
 
-void smc_wr_tx_dismiss_slots(struct smc_link *link, u8 wr_tx_hdr_type,
-			     smc_wr_tx_filter filter,
-			     smc_wr_tx_dismisser dismisser,
-			     unsigned long data)
-{
-	struct smc_wr_tx_pend_priv *tx_pend;
-	struct smc_wr_rx_hdr *wr_tx;
-	int i;
-
-	for_each_set_bit(i, link->wr_tx_mask, link->wr_tx_cnt) {
-		wr_tx = (struct smc_wr_rx_hdr *)&link->wr_tx_bufs[i];
-		if (wr_tx->type != wr_tx_hdr_type)
-			continue;
-		tx_pend = &link->wr_tx_pends[i].priv;
-		if (filter(tx_pend, data))
-			dismisser(tx_pend);
-	}
-}
-
 /****************************** receive queue ********************************/
 
 int smc_wr_rx_register_handler(struct smc_wr_rx_handler *handler)
@@ -517,6 +557,7 @@
 
 static void smc_wr_init_sge(struct smc_link *lnk)
 {
+	int sges_per_buf = (lnk->lgr->smc_version == SMC_V2) ? 2 : 1;
 	u32 i;
 
 	for (i = 0; i < lnk->wr_tx_cnt; i++) {
@@ -545,14 +586,44 @@
 		lnk->wr_tx_rdmas[i].wr_tx_rdma[1].wr.sg_list =
 			lnk->wr_tx_rdma_sges[i].tx_rdma_sge[1].wr_tx_rdma_sge;
 	}
+
+	if (lnk->lgr->smc_version == SMC_V2) {
+		lnk->wr_tx_v2_sge->addr = lnk->wr_tx_v2_dma_addr;
+		lnk->wr_tx_v2_sge->length = SMC_WR_BUF_V2_SIZE;
+		lnk->wr_tx_v2_sge->lkey = lnk->roce_pd->local_dma_lkey;
+
+		lnk->wr_tx_v2_ib->next = NULL;
+		lnk->wr_tx_v2_ib->sg_list = lnk->wr_tx_v2_sge;
+		lnk->wr_tx_v2_ib->num_sge = 1;
+		lnk->wr_tx_v2_ib->opcode = IB_WR_SEND;
+		lnk->wr_tx_v2_ib->send_flags =
+			IB_SEND_SIGNALED | IB_SEND_SOLICITED;
+	}
+
+	/* With SMC-Rv2 there can be messages larger than SMC_WR_TX_SIZE.
+	 * Each ib_recv_wr gets 2 sges, the second one is a spillover buffer
+	 * and the same buffer for all sges. When a larger message arrived then
+	 * the content of the first small sge is copied to the beginning of
+	 * the larger spillover buffer, allowing easy data mapping.
+	 */
 	for (i = 0; i < lnk->wr_rx_cnt; i++) {
-		lnk->wr_rx_sges[i].addr =
+		int x = i * sges_per_buf;
+
+		lnk->wr_rx_sges[x].addr =
 			lnk->wr_rx_dma_addr + i * SMC_WR_BUF_SIZE;
-		lnk->wr_rx_sges[i].length = SMC_WR_BUF_SIZE;
-		lnk->wr_rx_sges[i].lkey = lnk->roce_pd->local_dma_lkey;
+		lnk->wr_rx_sges[x].length = SMC_WR_TX_SIZE;
+		lnk->wr_rx_sges[x].lkey = lnk->roce_pd->local_dma_lkey;
+		if (lnk->lgr->smc_version == SMC_V2) {
+			lnk->wr_rx_sges[x + 1].addr =
+					lnk->wr_rx_v2_dma_addr + SMC_WR_TX_SIZE;
+			lnk->wr_rx_sges[x + 1].length =
+					SMC_WR_BUF_V2_SIZE - SMC_WR_TX_SIZE;
+			lnk->wr_rx_sges[x + 1].lkey =
+					lnk->roce_pd->local_dma_lkey;
+		}
 		lnk->wr_rx_ibs[i].next = NULL;
-		lnk->wr_rx_ibs[i].sg_list = &lnk->wr_rx_sges[i];
-		lnk->wr_rx_ibs[i].num_sge = 1;
+		lnk->wr_rx_ibs[i].sg_list = &lnk->wr_rx_sges[x];
+		lnk->wr_rx_ibs[i].num_sge = sges_per_buf;
 	}
 	lnk->wr_reg.wr.next = NULL;
 	lnk->wr_reg.wr.num_sge = 0;
@@ -572,10 +643,7 @@
 	smc_wr_wakeup_reg_wait(lnk);
 	smc_wr_wakeup_tx_wait(lnk);
 
-	if (smc_wr_tx_wait_no_pending_sends(lnk))
-		memset(lnk->wr_tx_mask, 0,
-		       BITS_TO_LONGS(SMC_WR_BUF_CNT) *
-						sizeof(*lnk->wr_tx_mask));
+	smc_wr_tx_wait_no_pending_sends(lnk);
 	wait_event(lnk->wr_reg_wait, (!atomic_read(&lnk->wr_reg_refcnt)));
 	wait_event(lnk->wr_tx_wait, (!atomic_read(&lnk->wr_tx_refcnt)));
 
@@ -585,16 +653,45 @@
 				    DMA_FROM_DEVICE);
 		lnk->wr_rx_dma_addr = 0;
 	}
+	if (lnk->wr_rx_v2_dma_addr) {
+		ib_dma_unmap_single(ibdev, lnk->wr_rx_v2_dma_addr,
+				    SMC_WR_BUF_V2_SIZE,
+				    DMA_FROM_DEVICE);
+		lnk->wr_rx_v2_dma_addr = 0;
+	}
 	if (lnk->wr_tx_dma_addr) {
 		ib_dma_unmap_single(ibdev, lnk->wr_tx_dma_addr,
 				    SMC_WR_BUF_SIZE * lnk->wr_tx_cnt,
 				    DMA_TO_DEVICE);
 		lnk->wr_tx_dma_addr = 0;
 	}
+	if (lnk->wr_tx_v2_dma_addr) {
+		ib_dma_unmap_single(ibdev, lnk->wr_tx_v2_dma_addr,
+				    SMC_WR_BUF_V2_SIZE,
+				    DMA_TO_DEVICE);
+		lnk->wr_tx_v2_dma_addr = 0;
+	}
+}
+
+void smc_wr_free_lgr_mem(struct smc_link_group *lgr)
+{
+	if (lgr->smc_version < SMC_V2)
+		return;
+
+	kfree(lgr->wr_rx_buf_v2);
+	lgr->wr_rx_buf_v2 = NULL;
+	kfree(lgr->wr_tx_buf_v2);
+	lgr->wr_tx_buf_v2 = NULL;
 }
 
 void smc_wr_free_link_mem(struct smc_link *lnk)
 {
+	kfree(lnk->wr_tx_v2_ib);
+	lnk->wr_tx_v2_ib = NULL;
+	kfree(lnk->wr_tx_v2_sge);
+	lnk->wr_tx_v2_sge = NULL;
+	kfree(lnk->wr_tx_v2_pend);
+	lnk->wr_tx_v2_pend = NULL;
 	kfree(lnk->wr_tx_compl);
 	lnk->wr_tx_compl = NULL;
 	kfree(lnk->wr_tx_pends);
@@ -619,8 +716,26 @@
 	lnk->wr_rx_bufs = NULL;
 }
 
+int smc_wr_alloc_lgr_mem(struct smc_link_group *lgr)
+{
+	if (lgr->smc_version < SMC_V2)
+		return 0;
+
+	lgr->wr_rx_buf_v2 = kzalloc(SMC_WR_BUF_V2_SIZE, GFP_KERNEL);
+	if (!lgr->wr_rx_buf_v2)
+		return -ENOMEM;
+	lgr->wr_tx_buf_v2 = kzalloc(SMC_WR_BUF_V2_SIZE, GFP_KERNEL);
+	if (!lgr->wr_tx_buf_v2) {
+		kfree(lgr->wr_rx_buf_v2);
+		return -ENOMEM;
+	}
+	return 0;
+}
+
 int smc_wr_alloc_link_mem(struct smc_link *link)
 {
+	int sges_per_buf = link->lgr->smc_version == SMC_V2 ? 2 : 1;
+
 	/* allocate link related memory */
 	link->wr_tx_bufs = kcalloc(SMC_WR_BUF_CNT, SMC_WR_BUF_SIZE, GFP_KERNEL);
 	if (!link->wr_tx_bufs)
@@ -653,7 +768,7 @@
 	if (!link->wr_tx_sges)
 		goto no_mem_wr_tx_rdma_sges;
 	link->wr_rx_sges = kcalloc(SMC_WR_BUF_CNT * 3,
-				   sizeof(link->wr_rx_sges[0]),
+				   sizeof(link->wr_rx_sges[0]) * sges_per_buf,
 				   GFP_KERNEL);
 	if (!link->wr_rx_sges)
 		goto no_mem_wr_tx_sges;
@@ -672,8 +787,29 @@
 				    GFP_KERNEL);
 	if (!link->wr_tx_compl)
 		goto no_mem_wr_tx_pends;
+
+	if (link->lgr->smc_version == SMC_V2) {
+		link->wr_tx_v2_ib = kzalloc(sizeof(*link->wr_tx_v2_ib),
+					    GFP_KERNEL);
+		if (!link->wr_tx_v2_ib)
+			goto no_mem_tx_compl;
+		link->wr_tx_v2_sge = kzalloc(sizeof(*link->wr_tx_v2_sge),
+					     GFP_KERNEL);
+		if (!link->wr_tx_v2_sge)
+			goto no_mem_v2_ib;
+		link->wr_tx_v2_pend = kzalloc(sizeof(*link->wr_tx_v2_pend),
+					      GFP_KERNEL);
+		if (!link->wr_tx_v2_pend)
+			goto no_mem_v2_sge;
+	}
 	return 0;
 
+no_mem_v2_sge:
+	kfree(link->wr_tx_v2_sge);
+no_mem_v2_ib:
+	kfree(link->wr_tx_v2_ib);
+no_mem_tx_compl:
+	kfree(link->wr_tx_compl);
 no_mem_wr_tx_pends:
 	kfree(link->wr_tx_pends);
 no_mem_wr_tx_mask:
@@ -725,6 +861,24 @@
 		rc = -EIO;
 		goto out;
 	}
+	if (lnk->lgr->smc_version == SMC_V2) {
+		lnk->wr_rx_v2_dma_addr = ib_dma_map_single(ibdev,
+			lnk->lgr->wr_rx_buf_v2, SMC_WR_BUF_V2_SIZE,
+			DMA_FROM_DEVICE);
+		if (ib_dma_mapping_error(ibdev, lnk->wr_rx_v2_dma_addr)) {
+			lnk->wr_rx_v2_dma_addr = 0;
+			rc = -EIO;
+			goto dma_unmap;
+		}
+		lnk->wr_tx_v2_dma_addr = ib_dma_map_single(ibdev,
+			lnk->lgr->wr_tx_buf_v2, SMC_WR_BUF_V2_SIZE,
+			DMA_TO_DEVICE);
+		if (ib_dma_mapping_error(ibdev, lnk->wr_tx_v2_dma_addr)) {
+			lnk->wr_tx_v2_dma_addr = 0;
+			rc = -EIO;
+			goto dma_unmap;
+		}
+	}
 	lnk->wr_tx_dma_addr = ib_dma_map_single(
 		ibdev, lnk->wr_tx_bufs,	SMC_WR_BUF_SIZE * lnk->wr_tx_cnt,
 		DMA_TO_DEVICE);
@@ -742,6 +896,18 @@
 	return rc;
 
 dma_unmap:
+	if (lnk->wr_rx_v2_dma_addr) {
+		ib_dma_unmap_single(ibdev, lnk->wr_rx_v2_dma_addr,
+				    SMC_WR_BUF_V2_SIZE,
+				    DMA_FROM_DEVICE);
+		lnk->wr_rx_v2_dma_addr = 0;
+	}
+	if (lnk->wr_tx_v2_dma_addr) {
+		ib_dma_unmap_single(ibdev, lnk->wr_tx_v2_dma_addr,
+				    SMC_WR_BUF_V2_SIZE,
+				    DMA_TO_DEVICE);
+		lnk->wr_tx_v2_dma_addr = 0;
+	}
 	ib_dma_unmap_single(ibdev, lnk->wr_rx_dma_addr,
 			    SMC_WR_BUF_SIZE * lnk->wr_rx_cnt,
 			    DMA_FROM_DEVICE);
--- linux-xilinx-zynqmp-5.15.0.orig/net/smc/smc_wr.h
+++ linux-xilinx-zynqmp-5.15.0/net/smc/smc_wr.h
@@ -22,7 +22,6 @@
 #define SMC_WR_BUF_CNT 16	/* # of ctrl buffers per link */
 
 #define SMC_WR_TX_WAIT_FREE_SLOT_TIME	(10 * HZ)
-#define SMC_WR_TX_WAIT_PENDING_TIME	(5 * HZ)
 
 #define SMC_WR_TX_SIZE 44 /* actual size of wr_send data (<=SMC_WR_BUF_SIZE) */
 
@@ -62,7 +61,7 @@
 
 static inline bool smc_wr_tx_link_hold(struct smc_link *link)
 {
-	if (!smc_link_usable(link))
+	if (!smc_link_sendable(link))
 		return false;
 	atomic_inc(&link->wr_tx_refcnt);
 	return true;
@@ -101,8 +100,10 @@
 
 int smc_wr_create_link(struct smc_link *lnk);
 int smc_wr_alloc_link_mem(struct smc_link *lnk);
+int smc_wr_alloc_lgr_mem(struct smc_link_group *lgr);
 void smc_wr_free_link(struct smc_link *lnk);
 void smc_wr_free_link_mem(struct smc_link *lnk);
+void smc_wr_free_lgr_mem(struct smc_link_group *lgr);
 void smc_wr_remember_qp_attr(struct smc_link *lnk);
 void smc_wr_remove_dev(struct smc_ib_device *smcibdev);
 void smc_wr_add_dev(struct smc_ib_device *smcibdev);
@@ -111,10 +112,16 @@
 			    struct smc_wr_buf **wr_buf,
 			    struct smc_rdma_wr **wrs,
 			    struct smc_wr_tx_pend_priv **wr_pend_priv);
+int smc_wr_tx_get_v2_slot(struct smc_link *link,
+			  smc_wr_tx_handler handler,
+			  struct smc_wr_v2_buf **wr_buf,
+			  struct smc_wr_tx_pend_priv **wr_pend_priv);
 int smc_wr_tx_put_slot(struct smc_link *link,
 		       struct smc_wr_tx_pend_priv *wr_pend_priv);
 int smc_wr_tx_send(struct smc_link *link,
 		   struct smc_wr_tx_pend_priv *wr_pend_priv);
+int smc_wr_tx_v2_send(struct smc_link *link,
+		      struct smc_wr_tx_pend_priv *priv, int len);
 int smc_wr_tx_send_wait(struct smc_link *link, struct smc_wr_tx_pend_priv *priv,
 			unsigned long timeout);
 void smc_wr_tx_cq_handler(struct ib_cq *ib_cq, void *cq_context);
@@ -122,7 +129,7 @@
 			     smc_wr_tx_filter filter,
 			     smc_wr_tx_dismisser dismisser,
 			     unsigned long data);
-int smc_wr_tx_wait_no_pending_sends(struct smc_link *link);
+void smc_wr_tx_wait_no_pending_sends(struct smc_link *link);
 
 int smc_wr_rx_register_handler(struct smc_wr_rx_handler *handler);
 int smc_wr_rx_post_init(struct smc_link *link);
--- linux-xilinx-zynqmp-5.15.0.orig/net/socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/socket.c
@@ -708,6 +708,14 @@
 	return ret;
 }
 
+static int __sock_sendmsg(struct socket *sock, struct msghdr *msg)
+{
+	int err = security_socket_sendmsg(sock, msg,
+					  msg_data_left(msg));
+
+	return err ?: sock_sendmsg_nosec(sock, msg);
+}
+
 /**
  *	sock_sendmsg - send a message through @sock
  *	@sock: socket
@@ -718,10 +726,21 @@
  */
 int sock_sendmsg(struct socket *sock, struct msghdr *msg)
 {
-	int err = security_socket_sendmsg(sock, msg,
-					  msg_data_left(msg));
+	struct sockaddr_storage *save_addr = (struct sockaddr_storage *)msg->msg_name;
+	struct sockaddr_storage address;
+	int save_len = msg->msg_namelen;
+	int ret;
 
-	return err ?: sock_sendmsg_nosec(sock, msg);
+	if (msg->msg_name) {
+		memcpy(&address, msg->msg_name, msg->msg_namelen);
+		msg->msg_name = &address;
+	}
+
+	ret = __sock_sendmsg(sock, msg);
+	msg->msg_name = save_addr;
+	msg->msg_namelen = save_len;
+
+	return ret;
 }
 EXPORT_SYMBOL(sock_sendmsg);
 
@@ -829,6 +848,7 @@
 	int empty = 1, false_tstamp = 0;
 	struct skb_shared_hwtstamps *shhwtstamps =
 		skb_hwtstamps(skb);
+	ktime_t hwtstamp;
 
 	/* Race occurred between timestamp enabling and packet
 	   receiving.  Fill in the current time for now. */
@@ -877,10 +897,12 @@
 	    (sk->sk_tsflags & SOF_TIMESTAMPING_RAW_HARDWARE) &&
 	    !skb_is_swtx_tstamp(skb, false_tstamp)) {
 		if (sk->sk_tsflags & SOF_TIMESTAMPING_BIND_PHC)
-			ptp_convert_timestamp(shhwtstamps, sk->sk_bind_phc);
+			hwtstamp = ptp_convert_timestamp(shhwtstamps,
+							 sk->sk_bind_phc);
+		else
+			hwtstamp = shhwtstamps->hwtstamp;
 
-		if (ktime_to_timespec64_cond(shhwtstamps->hwtstamp,
-					     tss.ts + 2)) {
+		if (ktime_to_timespec64_cond(hwtstamp, tss.ts + 2)) {
 			empty = 0;
 
 			if ((sk->sk_tsflags & SOF_TIMESTAMPING_OPT_PKTINFO) &&
@@ -1054,7 +1076,7 @@
 	if (sock->type == SOCK_SEQPACKET)
 		msg.msg_flags |= MSG_EOR;
 
-	res = sock_sendmsg(sock, &msg);
+	res = __sock_sendmsg(sock, &msg);
 	*from = msg.msg_iter;
 	return res;
 }
@@ -1462,8 +1484,13 @@
 	rcu_read_unlock();
 
 	err = pf->create(net, sock, protocol, kern);
-	if (err < 0)
+	if (err < 0) {
+		/* ->create should release the allocated sock->sk object on error
+		 * but it may leave the dangling pointer
+		 */
+		sock->sk = NULL;
 		goto out_module_put;
+	}
 
 	/*
 	 * Now to bump the refcnt of the [loadable] module that owns this
@@ -1718,7 +1745,7 @@
 
 	sock = sockfd_lookup_light(fd, &err, &fput_needed);
 	if (sock) {
-		somaxconn = sock_net(sock->sk)->core.sysctl_somaxconn;
+		somaxconn = READ_ONCE(sock_net(sock->sk)->core.sysctl_somaxconn);
 		if ((unsigned int)backlog > somaxconn)
 			backlog = somaxconn;
 
@@ -2033,7 +2060,7 @@
 	if (sock->file->f_flags & O_NONBLOCK)
 		flags |= MSG_DONTWAIT;
 	msg.msg_flags = flags;
-	err = sock_sendmsg(sock, &msg);
+	err = __sock_sendmsg(sock, &msg);
 
 out_put:
 	fput_light(sock->file, fput_needed);
@@ -2406,7 +2433,7 @@
 		err = sock_sendmsg_nosec(sock, msg_sys);
 		goto out_freectl;
 	}
-	err = sock_sendmsg(sock, msg_sys);
+	err = __sock_sendmsg(sock, msg_sys);
 	/*
 	 * If this is sendmmsg() and sending to current destination address was
 	 * successful, remember it.
@@ -2817,7 +2844,7 @@
 		 * error to return on the next call or if the
 		 * app asks about it using getsockopt(SO_ERROR).
 		 */
-		sock->sk->sk_err = -err;
+		WRITE_ONCE(sock->sk->sk_err, -err);
 	}
 out_put:
 	fput_light(sock->file, fput_needed);
@@ -3380,7 +3407,11 @@
 
 int kernel_bind(struct socket *sock, struct sockaddr *addr, int addrlen)
 {
-	return sock->ops->bind(sock, addr, addrlen);
+	struct sockaddr_storage address;
+
+	memcpy(&address, addr, addrlen);
+
+	return sock->ops->bind(sock, (struct sockaddr *)&address, addrlen);
 }
 EXPORT_SYMBOL(kernel_bind);
 
@@ -3450,7 +3481,12 @@
 int kernel_connect(struct socket *sock, struct sockaddr *addr, int addrlen,
 		   int flags)
 {
-	return sock->ops->connect(sock, addr, addrlen, flags);
+	struct sockaddr_storage address;
+
+	memcpy(&address, addr, addrlen);
+
+	return sock->ops->connect(sock, (struct sockaddr *)&address,
+					     addrlen, flags);
 }
 EXPORT_SYMBOL(kernel_connect);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/strparser/strparser.c
+++ linux-xilinx-zynqmp-5.15.0/net/strparser/strparser.c
@@ -27,18 +27,10 @@
 
 static struct workqueue_struct *strp_wq;
 
-struct _strp_msg {
-	/* Internal cb structure. struct strp_msg must be first for passing
-	 * to upper layer.
-	 */
-	struct strp_msg strp;
-	int accum_len;
-};
-
 static inline struct _strp_msg *_strp_msg(struct sk_buff *skb)
 {
 	return (struct _strp_msg *)((void *)skb->cb +
-		offsetof(struct qdisc_skb_cb, data));
+		offsetof(struct sk_skb_cb, strp));
 }
 
 /* Lower lock held */
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/addr.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/addr.c
@@ -162,8 +162,10 @@
 			      const size_t buflen, const char *delim,
 			      struct sockaddr_in6 *sin6)
 {
-	char *p;
+	char p[IPV6_SCOPE_ID_LEN + 1];
 	size_t len;
+	u32 scope_id = 0;
+	struct net_device *dev;
 
 	if ((buf + buflen) == delim)
 		return 1;
@@ -175,29 +177,23 @@
 		return 0;
 
 	len = (buf + buflen) - delim - 1;
-	p = kmemdup_nul(delim + 1, len, GFP_KERNEL);
-	if (p) {
-		u32 scope_id = 0;
-		struct net_device *dev;
-
-		dev = dev_get_by_name(net, p);
-		if (dev != NULL) {
-			scope_id = dev->ifindex;
-			dev_put(dev);
-		} else {
-			if (kstrtou32(p, 10, &scope_id) != 0) {
-				kfree(p);
-				return 0;
-			}
-		}
+	if (len > IPV6_SCOPE_ID_LEN)
+		return 0;
 
-		kfree(p);
+	memcpy(p, delim + 1, len);
+	p[len] = 0;
 
-		sin6->sin6_scope_id = scope_id;
-		return 1;
+	dev = dev_get_by_name(net, p);
+	if (dev != NULL) {
+		scope_id = dev->ifindex;
+		dev_put(dev);
+	} else {
+		if (kstrtou32(p, 10, &scope_id) != 0)
+			return 0;
 	}
 
-	return 0;
+	sin6->sin6_scope_id = scope_id;
+	return 1;
 }
 
 static size_t rpc_pton6(struct net *net, const char *buf, const size_t buflen,
@@ -288,10 +284,10 @@
 	}
 
 	if (snprintf(portbuf, sizeof(portbuf),
-		     ".%u.%u", port >> 8, port & 0xff) > (int)sizeof(portbuf))
+		     ".%u.%u", port >> 8, port & 0xff) >= (int)sizeof(portbuf))
 		return NULL;
 
-	if (strlcat(addrbuf, portbuf, sizeof(addrbuf)) > sizeof(addrbuf))
+	if (strlcat(addrbuf, portbuf, sizeof(addrbuf)) >= sizeof(addrbuf))
 		return NULL;
 
 	return kstrdup(addrbuf, gfp_flags);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/auth.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/auth.c
@@ -445,7 +445,7 @@
 		 * Enforce a 60 second garbage collection moratorium
 		 * Note that the cred_unused list must be time-ordered.
 		 */
-		if (!time_in_range(cred->cr_expire, expired, jiffies))
+		if (time_in_range(cred->cr_expire, expired, jiffies))
 			continue;
 		if (!rpcauth_unhash_cred(cred))
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/auth_gss/auth_gss.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/auth_gss/auth_gss.c
@@ -301,7 +301,7 @@
 	list_for_each_entry(pos, &pipe->in_downcall, list) {
 		if (!uid_eq(pos->uid, uid))
 			continue;
-		if (auth && pos->auth->service != auth->service)
+		if (pos->auth->service != auth->service)
 			continue;
 		refcount_inc(&pos->count);
 		return pos;
@@ -685,6 +685,21 @@
 	return err;
 }
 
+static struct gss_upcall_msg *
+gss_find_downcall(struct rpc_pipe *pipe, kuid_t uid)
+{
+	struct gss_upcall_msg *pos;
+	list_for_each_entry(pos, &pipe->in_downcall, list) {
+		if (!uid_eq(pos->uid, uid))
+			continue;
+		if (!rpc_msg_is_inflight(&pos->msg))
+			continue;
+		refcount_inc(&pos->count);
+		return pos;
+	}
+	return NULL;
+}
+
 #define MSG_BUF_MAXSIZE 1024
 
 static ssize_t
@@ -731,7 +746,7 @@
 	err = -ENOENT;
 	/* Find a matching upcall */
 	spin_lock(&pipe->lock);
-	gss_msg = __gss_find_upcall(pipe, uid, NULL);
+	gss_msg = gss_find_downcall(pipe, uid);
 	if (gss_msg == NULL) {
 		spin_unlock(&pipe->lock);
 		goto err_put_ctx;
@@ -1840,8 +1855,10 @@
 	offset = (u8 *)p - (u8 *)snd_buf->head[0].iov_base;
 	maj_stat = gss_wrap(ctx->gc_gss_ctx, offset, snd_buf, inpages);
 	/* slack space should prevent this ever happening: */
-	if (unlikely(snd_buf->len > snd_buf->buflen))
+	if (unlikely(snd_buf->len > snd_buf->buflen)) {
+		status = -EIO;
 		goto wrap_failed;
+	}
 	/* We're assuming that when GSS_S_CONTEXT_EXPIRED, the encryption was
 	 * done anyway, so it's safe to put the request on the wire: */
 	if (maj_stat == GSS_S_CONTEXT_EXPIRED)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/auth_gss/gss_krb5_keys.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/auth_gss/gss_krb5_keys.c
@@ -161,7 +161,7 @@
 	if (IS_ERR(cipher))
 		goto err_return;
 	if (crypto_sync_skcipher_setkey(cipher, inkey->data, inkey->len))
-		goto err_return;
+		goto err_free_cipher;
 
 	/* allocate and set up buffers */
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/auth_gss/gss_rpc_upcall.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/auth_gss/gss_rpc_upcall.c
@@ -98,6 +98,7 @@
 		 * done without the correct namespace:
 		 */
 		.flags		= RPC_CLNT_CREATE_NOPING |
+				  RPC_CLNT_CREATE_CONNECTED |
 				  RPC_CLNT_CREATE_NO_IDLE_TIMEOUT
 	};
 	struct rpc_clnt *clnt;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/auth_gss/gss_rpc_xdr.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/auth_gss/gss_rpc_xdr.c
@@ -250,8 +250,8 @@
 
 	creds = kzalloc(sizeof(struct svc_cred), GFP_KERNEL);
 	if (!creds) {
-		kfree(oa->data);
-		return -ENOMEM;
+		err = -ENOMEM;
+		goto free_oa;
 	}
 
 	oa->data[0].option.data = CREDS_VALUE;
@@ -265,29 +265,40 @@
 
 		/* option buffer */
 		p = xdr_inline_decode(xdr, 4);
-		if (unlikely(p == NULL))
-			return -ENOSPC;
+		if (unlikely(p == NULL)) {
+			err = -ENOSPC;
+			goto free_creds;
+		}
 
 		length = be32_to_cpup(p);
 		p = xdr_inline_decode(xdr, length);
-		if (unlikely(p == NULL))
-			return -ENOSPC;
+		if (unlikely(p == NULL)) {
+			err = -ENOSPC;
+			goto free_creds;
+		}
 
 		if (length == sizeof(CREDS_VALUE) &&
 		    memcmp(p, CREDS_VALUE, sizeof(CREDS_VALUE)) == 0) {
 			/* We have creds here. parse them */
 			err = gssx_dec_linux_creds(xdr, creds);
 			if (err)
-				return err;
+				goto free_creds;
 			oa->data[0].value.len = 1; /* presence */
 		} else {
 			/* consume uninteresting buffer */
 			err = gssx_dec_buffer(xdr, &dummy);
 			if (err)
-				return err;
+				goto free_creds;
 		}
 	}
 	return 0;
+
+free_creds:
+	kfree(creds);
+free_oa:
+	kfree(oa->data);
+	oa->data = NULL;
+	return err;
 }
 
 static int gssx_dec_status(struct xdr_stream *xdr,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/auth_gss/svcauth_gss.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/auth_gss/svcauth_gss.c
@@ -1132,17 +1132,11 @@
 
 static void gss_free_in_token_pages(struct gssp_in_token *in_token)
 {
-	u32 inlen;
 	int i;
 
 	i = 0;
-	inlen = in_token->page_len;
-	while (inlen) {
-		if (in_token->pages[i])
-			put_page(in_token->pages[i]);
-		inlen -= inlen > PAGE_SIZE ? PAGE_SIZE : inlen;
-	}
-
+	while (in_token->pages[i])
+		put_page(in_token->pages[i++]);
 	kfree(in_token->pages);
 	in_token->pages = NULL;
 }
@@ -1162,18 +1156,23 @@
 		return res;
 
 	inlen = svc_getnl(argv);
-	if (inlen > (argv->iov_len + rqstp->rq_arg.page_len))
+	if (inlen > (argv->iov_len + rqstp->rq_arg.page_len)) {
+		kfree(in_handle->data);
 		return SVC_DENIED;
+	}
 
 	pages = DIV_ROUND_UP(inlen, PAGE_SIZE);
-	in_token->pages = kcalloc(pages, sizeof(struct page *), GFP_KERNEL);
-	if (!in_token->pages)
+	in_token->pages = kcalloc(pages + 1, sizeof(struct page *), GFP_KERNEL);
+	if (!in_token->pages) {
+		kfree(in_handle->data);
 		return SVC_DENIED;
+	}
 	in_token->page_base = 0;
 	in_token->page_len = inlen;
 	for (i = 0; i < pages; i++) {
 		in_token->pages[i] = alloc_page(GFP_KERNEL);
 		if (!in_token->pages[i]) {
+			kfree(in_handle->data);
 			gss_free_in_token_pages(in_token);
 			return SVC_DENIED;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/backchannel_rqst.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/backchannel_rqst.c
@@ -64,6 +64,17 @@
 	kfree(req);
 }
 
+static void xprt_bc_reinit_xdr_buf(struct xdr_buf *buf)
+{
+	buf->head[0].iov_len = PAGE_SIZE;
+	buf->tail[0].iov_len = 0;
+	buf->pages = NULL;
+	buf->page_len = 0;
+	buf->flags = 0;
+	buf->len = 0;
+	buf->buflen = PAGE_SIZE;
+}
+
 static int xprt_alloc_xdr_buf(struct xdr_buf *buf, gfp_t gfp_flags)
 {
 	struct page *page;
@@ -292,6 +303,9 @@
 	 */
 	spin_lock_bh(&xprt->bc_pa_lock);
 	if (xprt_need_to_requeue(xprt)) {
+		xprt_bc_reinit_xdr_buf(&req->rq_snd_buf);
+		xprt_bc_reinit_xdr_buf(&req->rq_rcv_buf);
+		req->rq_rcv_buf.len = PAGE_SIZE;
 		list_add_tail(&req->rq_bc_pa_list, &xprt->bc_pa_list);
 		xprt->bc_alloc_count++;
 		atomic_inc(&xprt->bc_slot_count);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/cache.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/cache.c
@@ -1415,7 +1415,9 @@
 		seq_printf(m, "# expiry=%lld refcnt=%d flags=%lx\n",
 			   convert_to_wallclock(cp->expiry_time),
 			   kref_read(&cp->ref), cp->flags);
-	cache_get(cp);
+	if (!cache_get_rcu(cp))
+		return 0;
+
 	if (cache_check(cd, cp, NULL))
 		/* cache_check does a cache_put on failure */
 		seq_puts(m, "# ");
@@ -1657,12 +1659,14 @@
 	}
 }
 
-#ifdef CONFIG_PROC_FS
 static int create_cache_proc_entries(struct cache_detail *cd, struct net *net)
 {
 	struct proc_dir_entry *p;
 	struct sunrpc_net *sn;
 
+	if (!IS_ENABLED(CONFIG_PROC_FS))
+		return 0;
+
 	sn = net_generic(net, sunrpc_net_id);
 	cd->procfs = proc_mkdir(cd->name, sn->proc_net_rpc);
 	if (cd->procfs == NULL)
@@ -1690,12 +1694,6 @@
 	remove_cache_proc_entries(cd);
 	return -ENOMEM;
 }
-#else /* CONFIG_PROC_FS */
-static int create_cache_proc_entries(struct cache_detail *cd, struct net *net)
-{
-	return 0;
-}
-#endif
 
 void __init cache_initialize(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/clnt.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/clnt.c
@@ -76,6 +76,7 @@
 static int	rpc_decode_header(struct rpc_task *task,
 				  struct xdr_stream *xdr);
 static int	rpc_ping(struct rpc_clnt *clnt);
+static int	rpc_ping_noreply(struct rpc_clnt *clnt);
 static void	rpc_check_timeout(struct rpc_task *task);
 
 static void rpc_register_client(struct rpc_clnt *clnt)
@@ -110,7 +111,8 @@
 
 	pipefs_sb = rpc_get_sb_net(net);
 	if (pipefs_sb) {
-		__rpc_clnt_remove_pipedir(clnt);
+		if (pipefs_sb == clnt->pipefs_sb)
+			__rpc_clnt_remove_pipedir(clnt);
 		rpc_put_sb_net(net);
 	}
 }
@@ -150,6 +152,8 @@
 {
 	struct dentry *dentry;
 
+	clnt->pipefs_sb = pipefs_sb;
+
 	if (clnt->cl_program->pipe_dir_name != NULL) {
 		dentry = rpc_setup_pipedir_sb(pipefs_sb, clnt);
 		if (IS_ERR(dentry))
@@ -394,7 +398,7 @@
 	clnt->cl_maxproc  = version->nrprocs;
 	clnt->cl_prog     = args->prognumber ? : program->number;
 	clnt->cl_vers     = version->number;
-	clnt->cl_stats    = program->stats;
+	clnt->cl_stats    = args->stats ? : program->stats;
 	clnt->cl_metrics  = rpc_alloc_iostats(clnt);
 	rpc_init_pipe_dir_head(&clnt->cl_pipedir_objects);
 	err = -ENOMEM;
@@ -483,6 +487,12 @@
 			rpc_shutdown_client(clnt);
 			return ERR_PTR(err);
 		}
+	} else if (args->flags & RPC_CLNT_CREATE_CONNECTED) {
+		int err = rpc_ping_noreply(clnt);
+		if (err != 0) {
+			rpc_shutdown_client(clnt);
+			return ERR_PTR(err);
+		}
 	}
 
 	clnt->cl_softrtry = 1;
@@ -644,6 +654,7 @@
 	new->cl_discrtry = clnt->cl_discrtry;
 	new->cl_chatty = clnt->cl_chatty;
 	new->cl_principal = clnt->cl_principal;
+	new->cl_max_connect = clnt->cl_max_connect;
 	return new;
 
 out_err:
@@ -666,6 +677,7 @@
 		.version	= clnt->cl_vers,
 		.authflavor	= clnt->cl_auth->au_flavor,
 		.cred		= clnt->cl_cred,
+		.stats		= clnt->cl_stats,
 	};
 	return __rpc_clone_client(&args, clnt);
 }
@@ -688,6 +700,7 @@
 		.version	= clnt->cl_vers,
 		.authflavor	= flavor,
 		.cred		= clnt->cl_cred,
+		.stats		= clnt->cl_stats,
 	};
 	return __rpc_clone_client(&args, clnt);
 }
@@ -968,6 +981,8 @@
 		.version	= vers,
 		.authflavor	= old->cl_auth->au_flavor,
 		.cred		= old->cl_cred,
+		.stats		= old->cl_stats,
+		.timeout	= old->cl_timeout,
 	};
 	struct rpc_clnt *clnt;
 	int err;
@@ -1065,8 +1080,13 @@
 static
 void rpc_task_set_transport(struct rpc_task *task, struct rpc_clnt *clnt)
 {
-	if (task->tk_xprt)
-		return;
+	if (task->tk_xprt) {
+		if (!(test_bit(XPRT_OFFLINE, &task->tk_xprt->state) &&
+		      (task->tk_flags & RPC_TASK_MOVEABLE)))
+			return;
+		xprt_release(task);
+		xprt_put(task->tk_xprt);
+	}
 	if (task->tk_flags & RPC_TASK_NO_ROUND_ROBIN)
 		task->tk_xprt = rpc_task_get_first_xprt(clnt);
 	else
@@ -1076,24 +1096,21 @@
 static
 void rpc_task_set_client(struct rpc_task *task, struct rpc_clnt *clnt)
 {
-
-	if (clnt != NULL) {
-		rpc_task_set_transport(task, clnt);
-		task->tk_client = clnt;
-		refcount_inc(&clnt->cl_count);
-		if (clnt->cl_softrtry)
-			task->tk_flags |= RPC_TASK_SOFT;
-		if (clnt->cl_softerr)
-			task->tk_flags |= RPC_TASK_TIMEOUT;
-		if (clnt->cl_noretranstimeo)
-			task->tk_flags |= RPC_TASK_NO_RETRANS_TIMEOUT;
-		if (atomic_read(&clnt->cl_swapper))
-			task->tk_flags |= RPC_TASK_SWAPPER;
-		/* Add to the client's list of all tasks */
-		spin_lock(&clnt->cl_lock);
-		list_add_tail(&task->tk_task, &clnt->cl_tasks);
-		spin_unlock(&clnt->cl_lock);
-	}
+	rpc_task_set_transport(task, clnt);
+	task->tk_client = clnt;
+	refcount_inc(&clnt->cl_count);
+	if (clnt->cl_softrtry)
+		task->tk_flags |= RPC_TASK_SOFT;
+	if (clnt->cl_softerr)
+		task->tk_flags |= RPC_TASK_TIMEOUT;
+	if (clnt->cl_noretranstimeo)
+		task->tk_flags |= RPC_TASK_NO_RETRANS_TIMEOUT;
+	if (atomic_read(&clnt->cl_swapper))
+		task->tk_flags |= RPC_TASK_SWAPPER;
+	/* Add to the client's list of all tasks */
+	spin_lock(&clnt->cl_lock);
+	list_add_tail(&task->tk_task, &clnt->cl_tasks);
+	spin_unlock(&clnt->cl_lock);
 }
 
 static void
@@ -1362,7 +1379,7 @@
 		break;
 	default:
 		err = -EAFNOSUPPORT;
-		goto out;
+		goto out_release;
 	}
 	if (err < 0) {
 		dprintk("RPC:       can't bind UDP socket (%d)\n", err);
@@ -1868,7 +1885,7 @@
 			break;
 		case -EKEYEXPIRED:
 			if (!task->tk_cred_retry) {
-				rpc_exit(task, task->tk_status);
+				rpc_call_rpcerror(task, task->tk_status);
 			} else {
 				task->tk_action = call_refresh;
 				task->tk_cred_retry--;
@@ -1968,9 +1985,6 @@
 			status = -EOPNOTSUPP;
 			break;
 		}
-		if (task->tk_rebind_retry == 0)
-			break;
-		task->tk_rebind_retry--;
 		rpc_delay(task, 3*HZ);
 		goto retry_timeout;
 	case -ENOBUFS:
@@ -2078,6 +2092,7 @@
 	task->tk_status = 0;
 	switch (status) {
 	case -ECONNREFUSED:
+	case -ECONNRESET:
 		/* A positive refusal suggests a rebind is needed. */
 		if (RPC_IS_SOFTCONN(task))
 			break;
@@ -2086,7 +2101,6 @@
 			goto out_retry;
 		}
 		fallthrough;
-	case -ECONNRESET:
 	case -ECONNABORTED:
 	case -ENETDOWN:
 	case -ENETUNREACH:
@@ -2200,6 +2214,7 @@
 		 * socket just returned a connection error,
 		 * then hold onto the transport lock.
 		 */
+	case -ENOMEM:
 	case -ENOBUFS:
 		rpc_delay(task, HZ>>2);
 		fallthrough;
@@ -2208,12 +2223,13 @@
 		task->tk_action = call_transmit;
 		task->tk_status = 0;
 		break;
-	case -ECONNREFUSED:
 	case -EHOSTDOWN:
 	case -ENETDOWN:
 	case -EHOSTUNREACH:
 	case -ENETUNREACH:
 	case -EPERM:
+		break;
+	case -ECONNREFUSED:
 		if (RPC_IS_SOFTCONN(task)) {
 			if (!task->tk_msg.rpc_proc->p_proc)
 				trace_xprt_ping(task->tk_xprt,
@@ -2283,6 +2299,7 @@
 	case -ENOTCONN:
 	case -EPIPE:
 		break;
+	case -ENOMEM:
 	case -ENOBUFS:
 		rpc_delay(task, HZ>>2);
 		fallthrough;
@@ -2365,6 +2382,11 @@
 	case -EPIPE:
 	case -EAGAIN:
 		break;
+	case -ENFILE:
+	case -ENOBUFS:
+	case -ENOMEM:
+		rpc_delay(task, HZ>>2);
+		break;
 	case -EIO:
 		/* shutdown or soft timeout */
 		goto out_exit;
@@ -2375,8 +2397,7 @@
 		goto out_exit;
 	}
 	task->tk_action = call_encode;
-	if (status != -ECONNRESET && status != -ECONNABORTED)
-		rpc_check_timeout(task);
+	rpc_check_timeout(task);
 	return;
 out_exit:
 	rpc_call_rpcerror(task, status);
@@ -2651,6 +2672,7 @@
 	case rpc_autherr_rejectedverf:
 	case rpcsec_gsserr_credproblem:
 	case rpcsec_gsserr_ctxproblem:
+		rpcauth_invalcred(task);
 		if (!task->tk_cred_retry)
 			break;
 		task->tk_cred_retry--;
@@ -2692,6 +2714,10 @@
 	.p_decode = rpcproc_decode_null,
 };
 
+static const struct rpc_procinfo rpcproc_null_noreply = {
+	.p_encode = rpcproc_encode_null,
+};
+
 static void
 rpc_null_call_prepare(struct rpc_task *task, void *data)
 {
@@ -2745,6 +2771,28 @@
 	return status;
 }
 
+static int rpc_ping_noreply(struct rpc_clnt *clnt)
+{
+	struct rpc_message msg = {
+		.rpc_proc = &rpcproc_null_noreply,
+	};
+	struct rpc_task_setup task_setup_data = {
+		.rpc_client = clnt,
+		.rpc_message = &msg,
+		.callback_ops = &rpc_null_ops,
+		.flags = RPC_TASK_SOFT | RPC_TASK_SOFTCONN | RPC_TASK_NULLCREDS,
+	};
+	struct rpc_task	*task;
+	int status;
+
+	task = rpc_run_task(&task_setup_data);
+	if (IS_ERR(task))
+		return PTR_ERR(task);
+	status = task->tk_status;
+	rpc_put_task(task);
+	return status;
+}
+
 struct rpc_cb_add_xprt_calldata {
 	struct rpc_xprt_switch *xps;
 	struct rpc_xprt *xprt;
@@ -2778,19 +2826,22 @@
  * @clnt: pointer to struct rpc_clnt
  * @xps: pointer to struct rpc_xprt_switch,
  * @xprt: pointer struct rpc_xprt
- * @dummy: unused
+ * @in_max_connect: pointer to the max_connect value for the passed in xprt transport
  */
 int rpc_clnt_test_and_add_xprt(struct rpc_clnt *clnt,
 		struct rpc_xprt_switch *xps, struct rpc_xprt *xprt,
-		void *dummy)
+		void *in_max_connect)
 {
 	struct rpc_cb_add_xprt_calldata *data;
 	struct rpc_task *task;
+	int max_connect = clnt->cl_max_connect;
 
-	if (xps->xps_nunique_destaddr_xprts + 1 > clnt->cl_max_connect) {
+	if (in_max_connect)
+		max_connect = *(int *)in_max_connect;
+	if (xps->xps_nunique_destaddr_xprts + 1 > max_connect) {
 		rcu_read_lock();
 		pr_warn("SUNRPC: reached max allowed number (%d) did not add "
-			"transport to server: %s\n", clnt->cl_max_connect,
+			"transport to server: %s\n", max_connect,
 			rpc_peeraddr2str(clnt, RPC_DISPLAY_ADDR));
 		rcu_read_unlock();
 		return -EINVAL;
@@ -2903,7 +2954,7 @@
 	unsigned long connect_timeout;
 	unsigned long reconnect_timeout;
 	unsigned char resvport, reuseport;
-	int ret = 0;
+	int ret = 0, ident;
 
 	rcu_read_lock();
 	xps = xprt_switch_get(rcu_dereference(clnt->cl_xpi.xpi_xpswitch));
@@ -2917,8 +2968,11 @@
 	reuseport = xprt->reuseport;
 	connect_timeout = xprt->connect_timeout;
 	reconnect_timeout = xprt->max_reconnect_timeout;
+	ident = xprt->xprt_class->ident;
 	rcu_read_unlock();
 
+	if (!xprtargs->ident)
+		xprtargs->ident = ident;
 	xprt = xprt_create_transport(xprtargs);
 	if (IS_ERR(xprt)) {
 		ret = PTR_ERR(xprt);
@@ -3068,6 +3122,8 @@
 int
 rpc_clnt_swap_activate(struct rpc_clnt *clnt)
 {
+	while (clnt != clnt->cl_parent)
+		clnt = clnt->cl_parent;
 	if (atomic_inc_return(&clnt->cl_swapper) == 1)
 		return rpc_clnt_iterate_for_each_xprt(clnt,
 				rpc_clnt_swap_activate_callback, NULL);
@@ -3087,6 +3143,8 @@
 void
 rpc_clnt_swap_deactivate(struct rpc_clnt *clnt)
 {
+	while (clnt != clnt->cl_parent)
+		clnt = clnt->cl_parent;
 	if (atomic_dec_if_positive(&clnt->cl_swapper) == 0)
 		rpc_clnt_iterate_for_each_xprt(clnt,
 				rpc_clnt_swap_deactivate_callback, NULL);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/rpc_pipe.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/rpc_pipe.c
@@ -600,9 +600,9 @@
 
 	dget(dentry);
 	ret = simple_rmdir(dir, dentry);
+	d_drop(dentry);
 	if (!ret)
 		fsnotify_rmdir(dir, dentry);
-	d_delete(dentry);
 	dput(dentry);
 	return ret;
 }
@@ -613,9 +613,9 @@
 
 	dget(dentry);
 	ret = simple_unlink(dir, dentry);
+	d_drop(dentry);
 	if (!ret)
 		fsnotify_unlink(dir, dentry);
-	d_delete(dentry);
 	dput(dentry);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/rpcb_clnt.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/rpcb_clnt.c
@@ -746,6 +746,10 @@
 
 	child = rpcb_call_async(rpcb_clnt, map, proc);
 	rpc_release_client(rpcb_clnt);
+	if (IS_ERR(child)) {
+		/* rpcb_map_release() has freed the arguments */
+		return;
+	}
 
 	xprt->stat.bind_count++;
 	rpc_put_task(child);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/sched.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/sched.c
@@ -186,11 +186,6 @@
 
 /*
  * Add new request to wait queue.
- *
- * Swapper tasks always get inserted at the head of the queue.
- * This should avoid many nasty memory deadlocks and hopefully
- * improve overall performance.
- * Everyone else gets appended to the queue to ensure proper FIFO behavior.
  */
 static void __rpc_add_wait_queue(struct rpc_wait_queue *queue,
 		struct rpc_task *task,
@@ -199,8 +194,6 @@
 	INIT_LIST_HEAD(&task->u.tk_wait.timer_list);
 	if (RPC_IS_PRIORITY(queue))
 		__rpc_add_wait_queue_priority(queue, task, queue_priority);
-	else if (RPC_IS_SWAPPER(task))
-		list_add(&task->u.tk_wait.list, &queue->tasks[0]);
 	else
 		list_add_tail(&task->u.tk_wait.list, &queue->tasks[0]);
 	task->tk_waitqueue = queue;
@@ -355,8 +348,10 @@
 	if (RPC_IS_ASYNC(task)) {
 		INIT_WORK(&task->u.tk_work, rpc_async_schedule);
 		queue_work(wq, &task->u.tk_work);
-	} else
+	} else {
+		smp_mb__after_atomic();
 		wake_up_bit(&task->tk_runstate, RPC_TASK_QUEUED);
+	}
 }
 
 /*
@@ -803,7 +798,6 @@
 	/* Initialize retry counters */
 	task->tk_garb_retry = 2;
 	task->tk_cred_retry = 2;
-	task->tk_rebind_retry = 2;
 
 	/* starting timestamp */
 	task->tk_start = ktime_get();
@@ -1012,8 +1006,10 @@
 	struct rpc_buffer *buf;
 	gfp_t gfp = GFP_NOFS;
 
+	if (RPC_IS_ASYNC(task))
+		gfp = GFP_NOWAIT | __GFP_NOWARN;
 	if (RPC_IS_SWAPPER(task))
-		gfp = __GFP_MEMALLOC | GFP_NOWAIT | __GFP_NOWARN;
+		gfp |= __GFP_MEMALLOC;
 
 	size += sizeof(struct rpc_buffer);
 	if (size <= RPC_BUFFER_MAXSIZE)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/stats.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/stats.c
@@ -309,7 +309,7 @@
 struct proc_dir_entry *
 svc_proc_register(struct net *net, struct svc_stat *statp, const struct proc_ops *proc_ops)
 {
-	return do_register(net, statp->program->pg_name, statp, proc_ops);
+	return do_register(net, statp->program->pg_name, net, proc_ops);
 }
 EXPORT_SYMBOL_GPL(svc_proc_register);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/svc.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/svc.c
@@ -37,18 +37,37 @@
 
 static void svc_unregister(const struct svc_serv *serv, struct net *net);
 
-#define svc_serv_is_pooled(serv)    ((serv)->sv_ops->svo_function)
-
 #define SVC_POOL_DEFAULT	SVC_POOL_GLOBAL
 
 /*
+ * Mode for mapping cpus to pools.
+ */
+enum {
+	SVC_POOL_AUTO = -1,	/* choose one of the others */
+	SVC_POOL_GLOBAL,	/* no mapping, just a single global pool
+				 * (legacy & UP mode) */
+	SVC_POOL_PERCPU,	/* one pool per cpu */
+	SVC_POOL_PERNODE	/* one pool per numa node */
+};
+
+/*
  * Structure for mapping cpus to pools and vice versa.
  * Setup once during sunrpc initialisation.
  */
-struct svc_pool_map svc_pool_map = {
+
+struct svc_pool_map {
+	int count;			/* How many svc_servs use us */
+	int mode;			/* Note: int not enum to avoid
+					 * warnings about "enumeration value
+					 * not handled in switch" */
+	unsigned int npools;
+	unsigned int *pool_to;		/* maps pool id to cpu or node */
+	unsigned int *to_pool;		/* maps cpu or node to pool id */
+};
+
+static struct svc_pool_map svc_pool_map = {
 	.mode = SVC_POOL_DEFAULT
 };
-EXPORT_SYMBOL_GPL(svc_pool_map);
 
 static DEFINE_MUTEX(svc_pool_map_mutex);/* protects svc_pool_map.count only */
 
@@ -219,10 +238,12 @@
 
 /*
  * Add a reference to the global map of cpus to pools (and
- * vice versa).  Initialise the map if we're the first user.
- * Returns the number of pools.
+ * vice versa) if pools are in use.
+ * Initialise the map if we're the first user.
+ * Returns the number of pools. If this is '1', no reference
+ * was taken.
  */
-unsigned int
+static unsigned int
 svc_pool_map_get(void)
 {
 	struct svc_pool_map *m = &svc_pool_map;
@@ -232,6 +253,7 @@
 
 	if (m->count++) {
 		mutex_unlock(&svc_pool_map_mutex);
+		WARN_ON_ONCE(m->npools <= 1);
 		return m->npools;
 	}
 
@@ -247,30 +269,36 @@
 		break;
 	}
 
-	if (npools < 0) {
+	if (npools <= 0) {
 		/* default, or memory allocation failure */
 		npools = 1;
 		m->mode = SVC_POOL_GLOBAL;
 	}
 	m->npools = npools;
 
+	if (npools == 1)
+		/* service is unpooled, so doesn't hold a reference */
+		m->count--;
+
 	mutex_unlock(&svc_pool_map_mutex);
-	return m->npools;
+	return npools;
 }
-EXPORT_SYMBOL_GPL(svc_pool_map_get);
 
 /*
- * Drop a reference to the global map of cpus to pools.
+ * Drop a reference to the global map of cpus to pools, if
+ * pools were in use, i.e. if npools > 1.
  * When the last reference is dropped, the map data is
  * freed; this allows the sysadmin to change the pool
  * mode using the pool_mode module option without
  * rebooting or re-loading sunrpc.ko.
  */
-void
-svc_pool_map_put(void)
+static void
+svc_pool_map_put(int npools)
 {
 	struct svc_pool_map *m = &svc_pool_map;
 
+	if (npools <= 1)
+		return;
 	mutex_lock(&svc_pool_map_mutex);
 
 	if (!--m->count) {
@@ -283,7 +311,6 @@
 
 	mutex_unlock(&svc_pool_map_mutex);
 }
-EXPORT_SYMBOL_GPL(svc_pool_map_put);
 
 static int svc_pool_map_get_node(unsigned int pidx)
 {
@@ -340,21 +367,18 @@
 	struct svc_pool_map *m = &svc_pool_map;
 	unsigned int pidx = 0;
 
-	/*
-	 * An uninitialised map happens in a pure client when
-	 * lockd is brought up, so silently treat it the
-	 * same as SVC_POOL_GLOBAL.
-	 */
-	if (svc_serv_is_pooled(serv)) {
-		switch (m->mode) {
-		case SVC_POOL_PERCPU:
-			pidx = m->to_pool[cpu];
-			break;
-		case SVC_POOL_PERNODE:
-			pidx = m->to_pool[cpu_to_node(cpu)];
-			break;
-		}
+	if (serv->sv_nrpools <= 1)
+		return serv->sv_pools;
+
+	switch (m->mode) {
+	case SVC_POOL_PERCPU:
+		pidx = m->to_pool[cpu];
+		break;
+	case SVC_POOL_PERNODE:
+		pidx = m->to_pool[cpu_to_node(cpu)];
+		break;
 	}
+
 	return &serv->sv_pools[pidx % serv->sv_nrpools];
 }
 
@@ -423,8 +447,8 @@
  * Create an RPC service
  */
 static struct svc_serv *
-__svc_create(struct svc_program *prog, unsigned int bufsize, int npools,
-	     const struct svc_serv_ops *ops)
+__svc_create(struct svc_program *prog, struct svc_stat *stats,
+	     unsigned int bufsize, int npools, int (*threadfn)(void *data))
 {
 	struct svc_serv	*serv;
 	unsigned int vers;
@@ -435,13 +459,13 @@
 		return NULL;
 	serv->sv_name      = prog->pg_name;
 	serv->sv_program   = prog;
-	serv->sv_nrthreads = 1;
-	serv->sv_stats     = prog->pg_stats;
+	kref_init(&serv->sv_refcnt);
+	serv->sv_stats     = stats;
 	if (bufsize > RPCSVC_MAXPAYLOAD)
 		bufsize = RPCSVC_MAXPAYLOAD;
 	serv->sv_max_payload = bufsize? bufsize : 4096;
 	serv->sv_max_mesg  = roundup(serv->sv_max_payload + PAGE_SIZE, PAGE_SIZE);
-	serv->sv_ops = ops;
+	serv->sv_threadfn = threadfn;
 	xdrsize = 0;
 	while (prog) {
 		prog->pg_lovers = prog->pg_nvers-1;
@@ -487,59 +511,58 @@
 	return serv;
 }
 
-struct svc_serv *
-svc_create(struct svc_program *prog, unsigned int bufsize,
-	   const struct svc_serv_ops *ops)
+/**
+ * svc_create - Create an RPC service
+ * @prog: the RPC program the new service will handle
+ * @bufsize: maximum message size for @prog
+ * @threadfn: a function to service RPC requests for @prog
+ *
+ * Returns an instantiated struct svc_serv object or NULL.
+ */
+struct svc_serv *svc_create(struct svc_program *prog, unsigned int bufsize,
+			    int (*threadfn)(void *data))
 {
-	return __svc_create(prog, bufsize, /*npools*/1, ops);
+	return __svc_create(prog, NULL, bufsize, 1, threadfn);
 }
 EXPORT_SYMBOL_GPL(svc_create);
 
-struct svc_serv *
-svc_create_pooled(struct svc_program *prog, unsigned int bufsize,
-		  const struct svc_serv_ops *ops)
+/**
+ * svc_create_pooled - Create an RPC service with pooled threads
+ * @prog: the RPC program the new service will handle
+ * @stats: the stats struct if desired
+ * @bufsize: maximum message size for @prog
+ * @threadfn: a function to service RPC requests for @prog
+ *
+ * Returns an instantiated struct svc_serv object or NULL.
+ */
+struct svc_serv *svc_create_pooled(struct svc_program *prog,
+				   struct svc_stat *stats,
+				   unsigned int bufsize,
+				   int (*threadfn)(void *data))
 {
 	struct svc_serv *serv;
 	unsigned int npools = svc_pool_map_get();
 
-	serv = __svc_create(prog, bufsize, npools, ops);
+	serv = __svc_create(prog, stats, bufsize, npools, threadfn);
 	if (!serv)
 		goto out_err;
 	return serv;
 out_err:
-	svc_pool_map_put();
+	svc_pool_map_put(npools);
 	return NULL;
 }
 EXPORT_SYMBOL_GPL(svc_create_pooled);
 
-void svc_shutdown_net(struct svc_serv *serv, struct net *net)
-{
-	svc_close_net(serv, net);
-
-	if (serv->sv_ops->svo_shutdown)
-		serv->sv_ops->svo_shutdown(serv, net);
-}
-EXPORT_SYMBOL_GPL(svc_shutdown_net);
-
 /*
  * Destroy an RPC service. Should be called with appropriate locking to
- * protect the sv_nrthreads, sv_permsocks and sv_tempsocks.
+ * protect sv_permsocks and sv_tempsocks.
  */
 void
-svc_destroy(struct svc_serv *serv)
+svc_destroy(struct kref *ref)
 {
-	dprintk("svc: svc_destroy(%s, %d)\n",
-				serv->sv_program->pg_name,
-				serv->sv_nrthreads);
-
-	if (serv->sv_nrthreads) {
-		if (--(serv->sv_nrthreads) != 0) {
-			svc_sock_update_bufs(serv);
-			return;
-		}
-	} else
-		printk("svc_destroy: no threads for serv=%p!\n", serv);
+	struct svc_serv *serv = container_of(ref, struct svc_serv, sv_refcnt);
 
+	dprintk("svc: svc_destroy(%s)\n", serv->sv_program->pg_name);
 	del_timer_sync(&serv->sv_temptimer);
 
 	/*
@@ -551,8 +574,7 @@
 
 	cache_clean_deferred(serv);
 
-	if (svc_serv_is_pooled(serv))
-		svc_pool_map_put();
+	svc_pool_map_put(serv->sv_nrpools);
 
 	kfree(serv->sv_pools);
 	kfree(serv);
@@ -638,7 +660,7 @@
 }
 EXPORT_SYMBOL_GPL(svc_rqst_alloc);
 
-struct svc_rqst *
+static struct svc_rqst *
 svc_prepare_thread(struct svc_serv *serv, struct svc_pool *pool, int node)
 {
 	struct svc_rqst	*rqstp;
@@ -647,14 +669,17 @@
 	if (!rqstp)
 		return ERR_PTR(-ENOMEM);
 
-	serv->sv_nrthreads++;
+	svc_get(serv);
+	spin_lock_bh(&serv->sv_lock);
+	serv->sv_nrthreads += 1;
+	spin_unlock_bh(&serv->sv_lock);
+
 	spin_lock_bh(&pool->sp_lock);
 	pool->sp_nrthreads++;
 	list_add_rcu(&rqstp->rq_all, &pool->sp_all_threads);
 	spin_unlock_bh(&pool->sp_lock);
 	return rqstp;
 }
-EXPORT_SYMBOL_GPL(svc_prepare_thread);
 
 /*
  * Choose a pool in which to create a new thread, for svc_set_num_threads
@@ -728,11 +753,9 @@
 		if (IS_ERR(rqstp))
 			return PTR_ERR(rqstp);
 
-		__module_get(serv->sv_ops->svo_module);
-		task = kthread_create_on_node(serv->sv_ops->svo_function, rqstp,
+		task = kthread_create_on_node(serv->sv_threadfn, rqstp,
 					      node, "%s", serv->sv_name);
 		if (IS_ERR(task)) {
-			module_put(serv->sv_ops->svo_module);
 			svc_exit_thread(rqstp);
 			return PTR_ERR(task);
 		}
@@ -748,64 +771,19 @@
 	return 0;
 }
 
-
-/* destroy old threads */
-static int
-svc_signal_kthreads(struct svc_serv *serv, struct svc_pool *pool, int nrservs)
-{
-	struct task_struct *task;
-	unsigned int state = serv->sv_nrthreads-1;
-
-	/* destroy old threads */
-	do {
-		task = choose_victim(serv, pool, &state);
-		if (task == NULL)
-			break;
-		send_sig(SIGINT, task, 1);
-		nrservs++;
-	} while (nrservs < 0);
-
-	return 0;
-}
-
 /*
  * Create or destroy enough new threads to make the number
  * of threads the given number.  If `pool' is non-NULL, applies
  * only to threads in that pool, otherwise round-robins between
  * all pools.  Caller must ensure that mutual exclusion between this and
  * server startup or shutdown.
- *
- * Destroying threads relies on the service threads filling in
- * rqstp->rq_task, which only the nfs ones do.  Assumes the serv
- * has been created using svc_create_pooled().
- *
- * Based on code that used to be in nfsd_svc() but tweaked
- * to be pool-aware.
  */
-int
-svc_set_num_threads(struct svc_serv *serv, struct svc_pool *pool, int nrservs)
-{
-	if (pool == NULL) {
-		/* The -1 assumes caller has done a svc_get() */
-		nrservs -= (serv->sv_nrthreads-1);
-	} else {
-		spin_lock_bh(&pool->sp_lock);
-		nrservs -= pool->sp_nrthreads;
-		spin_unlock_bh(&pool->sp_lock);
-	}
-
-	if (nrservs > 0)
-		return svc_start_kthreads(serv, pool, nrservs);
-	if (nrservs < 0)
-		return svc_signal_kthreads(serv, pool, nrservs);
-	return 0;
-}
-EXPORT_SYMBOL_GPL(svc_set_num_threads);
 
 /* destroy old threads */
 static int
 svc_stop_kthreads(struct svc_serv *serv, struct svc_pool *pool, int nrservs)
 {
+	struct svc_rqst	*rqstp;
 	struct task_struct *task;
 	unsigned int state = serv->sv_nrthreads-1;
 
@@ -814,18 +792,20 @@
 		task = choose_victim(serv, pool, &state);
 		if (task == NULL)
 			break;
-		kthread_stop(task);
+		rqstp = kthread_data(task);
+		/* Did we lose a race to svo_function threadfn? */
+		if (kthread_stop(task) == -EINTR)
+			svc_exit_thread(rqstp);
 		nrservs++;
 	} while (nrservs < 0);
 	return 0;
 }
 
 int
-svc_set_num_threads_sync(struct svc_serv *serv, struct svc_pool *pool, int nrservs)
+svc_set_num_threads(struct svc_serv *serv, struct svc_pool *pool, int nrservs)
 {
 	if (pool == NULL) {
-		/* The -1 assumes caller has done a svc_get() */
-		nrservs -= (serv->sv_nrthreads-1);
+		nrservs -= serv->sv_nrthreads;
 	} else {
 		spin_lock_bh(&pool->sp_lock);
 		nrservs -= pool->sp_nrthreads;
@@ -838,7 +818,7 @@
 		return svc_stop_kthreads(serv, pool, nrservs);
 	return 0;
 }
-EXPORT_SYMBOL_GPL(svc_set_num_threads_sync);
+EXPORT_SYMBOL_GPL(svc_set_num_threads);
 
 /**
  * svc_rqst_replace_page - Replace one page in rq_pages[]
@@ -890,11 +870,14 @@
 		list_del_rcu(&rqstp->rq_all);
 	spin_unlock_bh(&pool->sp_lock);
 
+	spin_lock_bh(&serv->sv_lock);
+	serv->sv_nrthreads -= 1;
+	spin_unlock_bh(&serv->sv_lock);
+	svc_sock_update_bufs(serv);
+
 	svc_rqst_free(rqstp);
 
-	/* Release the server */
-	if (serv)
-		svc_destroy(serv);
+	svc_put(serv);
 }
 EXPORT_SYMBOL_GPL(svc_exit_thread);
 
@@ -1020,7 +1003,7 @@
 #endif
 	}
 
-	trace_svc_register(progname, version, protocol, port, family, error);
+	trace_svc_register(progname, version, family, protocol, port, error);
 	return error;
 }
 
@@ -1257,11 +1240,9 @@
 	if (rqstp->rq_proc >= versp->vs_nproc)
 		goto err_bad_proc;
 	rqstp->rq_procinfo = procp = &versp->vs_proc[rqstp->rq_proc];
-	if (!procp)
-		goto err_bad_proc;
 
 	/* Initialize storage for argp and resp */
-	memset(rqstp->rq_argp, 0, procp->pc_argsize);
+	memset(rqstp->rq_argp, 0, procp->pc_argzero);
 	memset(rqstp->rq_resp, 0, procp->pc_ressize);
 
 	/* Bump per-procedure stats counter */
@@ -1378,7 +1359,8 @@
 		goto err_bad_proc;
 
 	/* Syntactic check complete */
-	serv->sv_stats->rpccnt++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpccnt++;
 	trace_svc_process(rqstp, progp->pg_name);
 
 	/* Build the reply header. */
@@ -1434,7 +1416,7 @@
 	svc_authorise(rqstp);
 close_xprt:
 	if (rqstp->rq_xprt && test_bit(XPT_TEMP, &rqstp->rq_xprt->xpt_flags))
-		svc_close_xprt(rqstp->rq_xprt);
+		svc_xprt_close(rqstp->rq_xprt);
 	dprintk("svc: svc_process close\n");
 	return 0;
 
@@ -1444,7 +1426,8 @@
 	goto close_xprt;
 
 err_bad_rpc:
-	serv->sv_stats->rpcbadfmt++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpcbadfmt++;
 	svc_putnl(resv, 1);	/* REJECT */
 	svc_putnl(resv, 0);	/* RPC_MISMATCH */
 	svc_putnl(resv, 2);	/* Only RPCv2 supported */
@@ -1457,7 +1440,8 @@
 err_bad_auth:
 	dprintk("svc: authentication failed (%d)\n",
 		be32_to_cpu(rqstp->rq_auth_stat));
-	serv->sv_stats->rpcbadauth++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpcbadauth++;
 	/* Restore write pointer to location of accept status: */
 	xdr_ressize_check(rqstp, reply_statp);
 	svc_putnl(resv, 1);	/* REJECT */
@@ -1467,7 +1451,8 @@
 
 err_bad_prog:
 	dprintk("svc: unknown program %d\n", prog);
-	serv->sv_stats->rpcbadfmt++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpcbadfmt++;
 	svc_putnl(resv, RPC_PROG_UNAVAIL);
 	goto sendit;
 
@@ -1475,7 +1460,8 @@
 	svc_printk(rqstp, "unknown version (%d for prog %d, %s)\n",
 		       rqstp->rq_vers, rqstp->rq_prog, progp->pg_name);
 
-	serv->sv_stats->rpcbadfmt++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpcbadfmt++;
 	svc_putnl(resv, RPC_PROG_MISMATCH);
 	svc_putnl(resv, process.mismatch.lovers);
 	svc_putnl(resv, process.mismatch.hivers);
@@ -1484,7 +1470,8 @@
 err_bad_proc:
 	svc_printk(rqstp, "unknown procedure (%d)\n", rqstp->rq_proc);
 
-	serv->sv_stats->rpcbadfmt++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpcbadfmt++;
 	svc_putnl(resv, RPC_PROC_UNAVAIL);
 	goto sendit;
 
@@ -1493,7 +1480,8 @@
 
 	rpc_stat = rpc_garbage_args;
 err_bad:
-	serv->sv_stats->rpcbadfmt++;
+	if (serv->sv_stats)
+		serv->sv_stats->rpcbadfmt++;
 	svc_putnl(resv, ntohl(rpc_stat));
 	goto sendit;
 }
@@ -1534,7 +1522,8 @@
 	if (dir != 0) {
 		/* direction != CALL */
 		svc_printk(rqstp, "bad direction %d, dropping request\n", dir);
-		serv->sv_stats->rpcbadfmt++;
+		if (serv->sv_stats)
+			serv->sv_stats->rpcbadfmt++;
 		goto out_drop;
 	}
 
@@ -1676,16 +1665,17 @@
 /**
  * svc_fill_write_vector - Construct data argument for VFS write call
  * @rqstp: svc_rqst to operate on
- * @pages: list of pages containing data payload
- * @first: buffer containing first section of write payload
- * @total: total number of bytes of write payload
+ * @payload: xdr_buf containing only the write data payload
  *
  * Fills in rqstp::rq_vec, and returns the number of elements.
  */
-unsigned int svc_fill_write_vector(struct svc_rqst *rqstp, struct page **pages,
-				   struct kvec *first, size_t total)
+unsigned int svc_fill_write_vector(struct svc_rqst *rqstp,
+				   struct xdr_buf *payload)
 {
+	struct page **pages = payload->pages;
+	struct kvec *first = payload->head;
 	struct kvec *vec = rqstp->rq_vec;
+	size_t total = payload->len;
 	unsigned int i;
 
 	/* Some types of transport can present the write payload
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/svc_xprt.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/svc_xprt.c
@@ -243,7 +243,7 @@
 	xprt = xcl->xcl_ops->xpo_create(serv, net, sap, len, flags);
 	if (IS_ERR(xprt))
 		trace_svc_xprt_create_err(serv->sv_program->pg_name,
-					  xcl->xcl_name, sap, xprt);
+					  xcl->xcl_name, sap, len, xprt);
 	return xprt;
 }
 
@@ -267,12 +267,12 @@
 	trace_svc_xprt_received(xprt);
 
 	/* As soon as we clear busy, the xprt could be closed and
-	 * 'put', so we need a reference to call svc_enqueue_xprt with:
+	 * 'put', so we need a reference to call svc_xprt_enqueue with:
 	 */
 	svc_xprt_get(xprt);
 	smp_mb__before_atomic();
 	clear_bit(XPT_BUSY, &xprt->xpt_flags);
-	xprt->xpt_server->sv_ops->svo_enqueue_xprt(xprt);
+	svc_xprt_enqueue(xprt);
 	svc_xprt_put(xprt);
 }
 EXPORT_SYMBOL_GPL(svc_xprt_received);
@@ -286,7 +286,7 @@
 	svc_xprt_received(new);
 }
 
-static int _svc_create_xprt(struct svc_serv *serv, const char *xprt_name,
+static int _svc_xprt_create(struct svc_serv *serv, const char *xprt_name,
 			    struct net *net, const int family,
 			    const unsigned short port, int flags,
 			    const struct cred *cred)
@@ -322,21 +322,35 @@
 	return -EPROTONOSUPPORT;
 }
 
-int svc_create_xprt(struct svc_serv *serv, const char *xprt_name,
+/**
+ * svc_xprt_create - Add a new listener to @serv
+ * @serv: target RPC service
+ * @xprt_name: transport class name
+ * @net: network namespace
+ * @family: network address family
+ * @port: listener port
+ * @flags: SVC_SOCK flags
+ * @cred: credential to bind to this transport
+ *
+ * Return values:
+ *   %0: New listener added successfully
+ *   %-EPROTONOSUPPORT: Requested transport type not supported
+ */
+int svc_xprt_create(struct svc_serv *serv, const char *xprt_name,
 		    struct net *net, const int family,
 		    const unsigned short port, int flags,
 		    const struct cred *cred)
 {
 	int err;
 
-	err = _svc_create_xprt(serv, xprt_name, net, family, port, flags, cred);
+	err = _svc_xprt_create(serv, xprt_name, net, family, port, flags, cred);
 	if (err == -EPROTONOSUPPORT) {
 		request_module("svc%s", xprt_name);
-		err = _svc_create_xprt(serv, xprt_name, net, family, port, flags, cred);
+		err = _svc_xprt_create(serv, xprt_name, net, family, port, flags, cred);
 	}
 	return err;
 }
-EXPORT_SYMBOL_GPL(svc_create_xprt);
+EXPORT_SYMBOL_GPL(svc_xprt_create);
 
 /*
  * Copy the local and remote xprt addresses to the rqstp structure
@@ -412,6 +426,8 @@
 	smp_rmb();
 	xpt_flags = READ_ONCE(xprt->xpt_flags);
 
+	if (xpt_flags & BIT(XPT_BUSY))
+		return false;
 	if (xpt_flags & (BIT(XPT_CONN) | BIT(XPT_CLOSE)))
 		return true;
 	if (xpt_flags & (BIT(XPT_DATA) | BIT(XPT_DEFERRED))) {
@@ -424,7 +440,12 @@
 	return false;
 }
 
-void svc_xprt_do_enqueue(struct svc_xprt *xprt)
+/**
+ * svc_xprt_enqueue - Queue a transport on an idle nfsd thread
+ * @xprt: transport with data pending
+ *
+ */
+void svc_xprt_enqueue(struct svc_xprt *xprt)
 {
 	struct svc_pool *pool;
 	struct svc_rqst	*rqstp = NULL;
@@ -468,19 +489,6 @@
 	put_cpu();
 	trace_svc_xprt_do_enqueue(xprt, rqstp);
 }
-EXPORT_SYMBOL_GPL(svc_xprt_do_enqueue);
-
-/*
- * Queue up a transport with data pending. If there are idle nfsd
- * processes, wake 'em up.
- *
- */
-void svc_xprt_enqueue(struct svc_xprt *xprt)
-{
-	if (test_bit(XPT_BUSY, &xprt->xpt_flags))
-		return;
-	xprt->xpt_server->sv_ops->svo_enqueue_xprt(xprt);
-}
 EXPORT_SYMBOL_GPL(svc_xprt_enqueue);
 
 /*
@@ -530,13 +538,23 @@
 }
 EXPORT_SYMBOL_GPL(svc_reserve);
 
+static void free_deferred(struct svc_xprt *xprt, struct svc_deferred_req *dr)
+{
+	if (!dr)
+		return;
+
+	xprt->xpt_ops->xpo_release_ctxt(xprt, dr->xprt_ctxt);
+	kfree(dr);
+}
+
 static void svc_xprt_release(struct svc_rqst *rqstp)
 {
 	struct svc_xprt	*xprt = rqstp->rq_xprt;
 
-	xprt->xpt_ops->xpo_release_rqst(rqstp);
+	xprt->xpt_ops->xpo_release_ctxt(xprt, rqstp->rq_xprt_ctxt);
+	rqstp->rq_xprt_ctxt = NULL;
 
-	kfree(rqstp->rq_deferred);
+	free_deferred(xprt, rqstp->rq_deferred);
 	rqstp->rq_deferred = NULL;
 
 	pagevec_release(&rqstp->rq_pvec);
@@ -682,12 +700,12 @@
 			/* Made progress, don't sleep yet */
 			continue;
 
-		set_current_state(TASK_INTERRUPTIBLE);
-		if (signalled() || kthread_should_stop()) {
+		set_current_state(TASK_IDLE);
+		if (kthread_should_stop()) {
 			set_current_state(TASK_RUNNING);
 			return -EINTR;
 		}
-		schedule_timeout(msecs_to_jiffies(500));
+		freezable_schedule_timeout(msecs_to_jiffies(500));
 	}
 	rqstp->rq_page_end = &rqstp->rq_pages[pages];
 	rqstp->rq_pages[pages] = NULL; /* this might be seen in nfsd_splice_actor() */
@@ -718,7 +736,7 @@
 		return false;
 
 	/* are we shutting down? */
-	if (signalled() || kthread_should_stop())
+	if (kthread_should_stop())
 		return false;
 
 	/* are we freezing? */
@@ -740,18 +758,14 @@
 	if (rqstp->rq_xprt)
 		goto out_found;
 
-	/*
-	 * We have to be able to interrupt this wait
-	 * to bring down the daemons ...
-	 */
-	set_current_state(TASK_INTERRUPTIBLE);
+	set_current_state(TASK_IDLE);
 	smp_mb__before_atomic();
 	clear_bit(SP_CONGESTED, &pool->sp_flags);
 	clear_bit(RQ_BUSY, &rqstp->rq_flags);
 	smp_mb__after_atomic();
 
 	if (likely(rqst_should_sleep(rqstp)))
-		time_left = schedule_timeout(timeout);
+		time_left = freezable_schedule_timeout(timeout);
 	else
 		__set_current_state(TASK_RUNNING);
 
@@ -766,7 +780,7 @@
 	if (!time_left)
 		atomic_long_inc(&pool->sp_stats.threads_timedout);
 
-	if (signalled() || kthread_should_stop())
+	if (kthread_should_stop())
 		return ERR_PTR(-EINTR);
 	return ERR_PTR(-EAGAIN);
 out_found:
@@ -864,7 +878,7 @@
 	try_to_freeze();
 	cond_resched();
 	err = -EINTR;
-	if (signalled() || kthread_should_stop())
+	if (kthread_should_stop())
 		goto out;
 
 	xprt = svc_get_next_xprt(rqstp, timeout);
@@ -1054,13 +1068,18 @@
 	spin_unlock_bh(&serv->sv_lock);
 
 	while ((dr = svc_deferred_dequeue(xprt)) != NULL)
-		kfree(dr);
+		free_deferred(xprt, dr);
 
 	call_xpt_users(xprt);
 	svc_xprt_put(xprt);
 }
 
-void svc_close_xprt(struct svc_xprt *xprt)
+/**
+ * svc_xprt_close - Close a client connection
+ * @xprt: transport to disconnect
+ *
+ */
+void svc_xprt_close(struct svc_xprt *xprt)
 {
 	trace_svc_xprt_close(xprt);
 	set_bit(XPT_CLOSE, &xprt->xpt_flags);
@@ -1075,7 +1094,7 @@
 	 */
 	svc_delete_xprt(xprt);
 }
-EXPORT_SYMBOL_GPL(svc_close_xprt);
+EXPORT_SYMBOL_GPL(svc_xprt_close);
 
 static int svc_close_list(struct svc_serv *serv, struct list_head *xprt_list, struct net *net)
 {
@@ -1127,7 +1146,11 @@
 	}
 }
 
-/*
+/**
+ * svc_xprt_destroy_all - Destroy transports associated with @serv
+ * @serv: RPC service to be shut down
+ * @net: target network namespace
+ *
  * Server threads may still be running (especially in the case where the
  * service is still running in other network namespaces).
  *
@@ -1139,7 +1162,7 @@
  * threads, we may need to wait a little while and then check again to
  * see if they're done.
  */
-void svc_close_net(struct svc_serv *serv, struct net *net)
+void svc_xprt_destroy_all(struct svc_serv *serv, struct net *net)
 {
 	int delay = 0;
 
@@ -1150,6 +1173,7 @@
 		msleep(delay++);
 	}
 }
+EXPORT_SYMBOL_GPL(svc_xprt_destroy_all);
 
 /*
  * Handle defer and revisit of requests
@@ -1166,8 +1190,8 @@
 	if (too_many || test_bit(XPT_DEAD, &xprt->xpt_flags)) {
 		spin_unlock(&xprt->xpt_lock);
 		trace_svc_defer_drop(dr);
+		free_deferred(xprt, dr);
 		svc_xprt_put(xprt);
-		kfree(dr);
 		return;
 	}
 	dr->xprt = NULL;
@@ -1212,13 +1236,14 @@
 		dr->addrlen = rqstp->rq_addrlen;
 		dr->daddr = rqstp->rq_daddr;
 		dr->argslen = rqstp->rq_arg.len >> 2;
-		dr->xprt_hlen = rqstp->rq_xprt_hlen;
 
 		/* back up head to the start of the buffer and copy */
 		skip = rqstp->rq_arg.len - rqstp->rq_arg.head[0].iov_len;
 		memcpy(dr->args, rqstp->rq_arg.head[0].iov_base - skip,
 		       dr->argslen << 2);
 	}
+	dr->xprt_ctxt = rqstp->rq_xprt_ctxt;
+	rqstp->rq_xprt_ctxt = NULL;
 	trace_svc_defer(rqstp);
 	svc_xprt_get(rqstp->rq_xprt);
 	dr->xprt = rqstp->rq_xprt;
@@ -1238,21 +1263,23 @@
 	trace_svc_defer_recv(dr);
 
 	/* setup iov_base past transport header */
-	rqstp->rq_arg.head[0].iov_base = dr->args + (dr->xprt_hlen>>2);
+	rqstp->rq_arg.head[0].iov_base = dr->args;
 	/* The iov_len does not include the transport header bytes */
-	rqstp->rq_arg.head[0].iov_len = (dr->argslen<<2) - dr->xprt_hlen;
+	rqstp->rq_arg.head[0].iov_len = dr->argslen << 2;
 	rqstp->rq_arg.page_len = 0;
 	/* The rq_arg.len includes the transport header bytes */
-	rqstp->rq_arg.len     = dr->argslen<<2;
+	rqstp->rq_arg.len     = dr->argslen << 2;
 	rqstp->rq_prot        = dr->prot;
 	memcpy(&rqstp->rq_addr, &dr->addr, dr->addrlen);
 	rqstp->rq_addrlen     = dr->addrlen;
 	/* Save off transport header len in case we get deferred again */
-	rqstp->rq_xprt_hlen   = dr->xprt_hlen;
 	rqstp->rq_daddr       = dr->daddr;
 	rqstp->rq_respages    = rqstp->rq_pages;
+	rqstp->rq_xprt_ctxt   = dr->xprt_ctxt;
+
+	dr->xprt_ctxt = NULL;
 	svc_xprt_received(rqstp->rq_xprt);
-	return (dr->argslen<<2) - dr->xprt_hlen;
+	return dr->argslen << 2;
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/svcauth_unix.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/svcauth_unix.c
@@ -415,14 +415,23 @@
 	return hash_long(from_kuid(&init_user_ns, uid), GID_HASHBITS);
 }
 
-static void unix_gid_put(struct kref *kref)
+static void unix_gid_free(struct rcu_head *rcu)
 {
-	struct cache_head *item = container_of(kref, struct cache_head, ref);
-	struct unix_gid *ug = container_of(item, struct unix_gid, h);
+	struct unix_gid *ug = container_of(rcu, struct unix_gid, rcu);
+	struct cache_head *item = &ug->h;
+
 	if (test_bit(CACHE_VALID, &item->flags) &&
 	    !test_bit(CACHE_NEGATIVE, &item->flags))
 		put_group_info(ug->gi);
-	kfree_rcu(ug, rcu);
+	kfree(ug);
+}
+
+static void unix_gid_put(struct kref *kref)
+{
+	struct cache_head *item = container_of(kref, struct cache_head, ref);
+	struct unix_gid *ug = container_of(item, struct unix_gid, h);
+
+	call_rcu(&ug->rcu, unix_gid_free);
 }
 
 static int unix_gid_match(struct cache_head *corig, struct cache_head *cnew)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/svcsock.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/svcsock.c
@@ -111,36 +111,27 @@
 #endif
 
 /**
- * svc_tcp_release_rqst - Release transport-related resources
- * @rqstp: request structure with resources to be released
+ * svc_tcp_release_ctxt - Release transport-related resources
+ * @xprt: the transport which owned the context
+ * @ctxt: the context from rqstp->rq_xprt_ctxt or dr->xprt_ctxt
  *
  */
-static void svc_tcp_release_rqst(struct svc_rqst *rqstp)
+static void svc_tcp_release_ctxt(struct svc_xprt *xprt, void *ctxt)
 {
-	struct sk_buff *skb = rqstp->rq_xprt_ctxt;
-
-	if (skb) {
-		struct svc_sock *svsk =
-			container_of(rqstp->rq_xprt, struct svc_sock, sk_xprt);
-
-		rqstp->rq_xprt_ctxt = NULL;
-		skb_free_datagram_locked(svsk->sk_sk, skb);
-	}
 }
 
 /**
- * svc_udp_release_rqst - Release transport-related resources
- * @rqstp: request structure with resources to be released
+ * svc_udp_release_ctxt - Release transport-related resources
+ * @xprt: the transport which owned the context
+ * @ctxt: the context from rqstp->rq_xprt_ctxt or dr->xprt_ctxt
  *
  */
-static void svc_udp_release_rqst(struct svc_rqst *rqstp)
+static void svc_udp_release_ctxt(struct svc_xprt *xprt, void *ctxt)
 {
-	struct sk_buff *skb = rqstp->rq_xprt_ctxt;
+	struct sk_buff *skb = ctxt;
 
-	if (skb) {
-		rqstp->rq_xprt_ctxt = NULL;
+	if (skb)
 		consume_skb(skb);
-	}
 }
 
 union svc_pktinfo_u {
@@ -259,8 +250,6 @@
 	ssize_t len;
 	size_t t;
 
-	rqstp->rq_xprt_hlen = 0;
-
 	clear_bit(XPT_DATA, &svsk->sk_xprt.xpt_flags);
 
 	for (i = 0, t = 0; t < buflen; i++, t += PAGE_SIZE) {
@@ -570,7 +559,8 @@
 	unsigned int sent;
 	int err;
 
-	svc_udp_release_rqst(rqstp);
+	svc_udp_release_ctxt(xprt, rqstp->rq_xprt_ctxt);
+	rqstp->rq_xprt_ctxt = NULL;
 
 	svc_set_cmsg_data(rqstp, cmh);
 
@@ -639,7 +629,7 @@
 	.xpo_recvfrom = svc_udp_recvfrom,
 	.xpo_sendto = svc_udp_sendto,
 	.xpo_result_payload = svc_sock_result_payload,
-	.xpo_release_rqst = svc_udp_release_rqst,
+	.xpo_release_ctxt = svc_udp_release_ctxt,
 	.xpo_detach = svc_sock_detach,
 	.xpo_free = svc_sock_free,
 	.xpo_has_wspace = svc_udp_has_wspace,
@@ -695,12 +685,6 @@
 {
 	struct svc_sock	*svsk = (struct svc_sock *)sk->sk_user_data;
 
-	if (svsk) {
-		/* Refer to svc_setup_socket() for details. */
-		rmb();
-		svsk->sk_odata(sk);
-	}
-
 	/*
 	 * This callback may called twice when a new connection
 	 * is established as a child socket inherits everything
@@ -709,13 +693,18 @@
 	 *    when one of child sockets become ESTABLISHED.
 	 * 2) data_ready method of the child socket may be called
 	 *    when it receives data before the socket is accepted.
-	 * In case of 2, we should ignore it silently.
+	 * In case of 2, we should ignore it silently and DO NOT
+	 * dereference svsk.
 	 */
-	if (sk->sk_state == TCP_LISTEN) {
-		if (svsk) {
-			set_bit(XPT_CONN, &svsk->sk_xprt.xpt_flags);
-			svc_xprt_enqueue(&svsk->sk_xprt);
-		}
+	if (sk->sk_state != TCP_LISTEN)
+		return;
+
+	if (svsk) {
+		/* Refer to svc_setup_socket() for details. */
+		rmb();
+		svsk->sk_odata(sk);
+		set_bit(XPT_CONN, &svsk->sk_xprt.xpt_flags);
+		svc_xprt_enqueue(&svsk->sk_xprt);
 	}
 }
 
@@ -1096,7 +1085,9 @@
 	int ret;
 
 	*sentp = 0;
-	xdr_alloc_bvec(xdr, GFP_KERNEL);
+	ret = xdr_alloc_bvec(xdr, GFP_KERNEL);
+	if (ret < 0)
+		return ret;
 
 	ret = kernel_sendmsg(sock, &msg, &rm, 1, rm.iov_len);
 	if (ret < 0)
@@ -1165,7 +1156,8 @@
 	unsigned int sent;
 	int err;
 
-	svc_tcp_release_rqst(rqstp);
+	svc_tcp_release_ctxt(xprt, rqstp->rq_xprt_ctxt);
+	rqstp->rq_xprt_ctxt = NULL;
 
 	atomic_inc(&svsk->sk_sendqlen);
 	mutex_lock(&xprt->xpt_mutex);
@@ -1210,7 +1202,7 @@
 	.xpo_recvfrom = svc_tcp_recvfrom,
 	.xpo_sendto = svc_tcp_sendto,
 	.xpo_result_payload = svc_sock_result_payload,
-	.xpo_release_rqst = svc_tcp_release_rqst,
+	.xpo_release_ctxt = svc_tcp_release_ctxt,
 	.xpo_detach = svc_tcp_sock_detach,
 	.xpo_free = svc_sock_free,
 	.xpo_has_wspace = svc_tcp_has_wspace,
@@ -1342,25 +1334,10 @@
 	return svsk;
 }
 
-bool svc_alien_sock(struct net *net, int fd)
-{
-	int err;
-	struct socket *sock = sockfd_lookup(fd, &err);
-	bool ret = false;
-
-	if (!sock)
-		goto out;
-	if (sock_net(sock->sk) != net)
-		ret = true;
-	sockfd_put(sock);
-out:
-	return ret;
-}
-EXPORT_SYMBOL_GPL(svc_alien_sock);
-
 /**
  * svc_addsock - add a listener socket to an RPC service
  * @serv: pointer to RPC service to which to add a new listener
+ * @net: caller's network namespace
  * @fd: file descriptor of the new listener
  * @name_return: pointer to buffer to fill in with name of listener
  * @len: size of the buffer
@@ -1370,8 +1347,8 @@
  * Name is terminated with '\n'.  On error, returns a negative errno
  * value.
  */
-int svc_addsock(struct svc_serv *serv, const int fd, char *name_return,
-		const size_t len, const struct cred *cred)
+int svc_addsock(struct svc_serv *serv, struct net *net, const int fd,
+		char *name_return, const size_t len, const struct cred *cred)
 {
 	int err = 0;
 	struct socket *so = sockfd_lookup(fd, &err);
@@ -1382,6 +1359,9 @@
 
 	if (!so)
 		return err;
+	err = -EINVAL;
+	if (sock_net(so->sk) != net)
+		goto out;
 	err = -EAFNOSUPPORT;
 	if ((so->sk->sk_family != PF_INET) && (so->sk->sk_family != PF_INET6))
 		goto out;
@@ -1474,6 +1454,9 @@
 	newlen = error;
 
 	if (protocol == IPPROTO_TCP) {
+		sock->sk->sk_net_refcnt = 1;
+		get_net(net);
+		sock_inuse_add(net, 1);
 		if ((error = kernel_listen(sock, 64)) < 0)
 			goto bummer;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/sysfs.c
@@ -282,8 +282,10 @@
 	int offline = 0, online = 0, remove = 0;
 	struct rpc_xprt_switch *xps = rpc_sysfs_xprt_kobj_get_xprt_switch(kobj);
 
-	if (!xprt)
-		return 0;
+	if (!xprt || !xps) {
+		count = 0;
+		goto out_put;
+	}
 
 	if (!strncmp(buf, "offline", 7))
 		offline = 1;
@@ -291,8 +293,10 @@
 		online = 1;
 	else if (!strncmp(buf, "remove", 6))
 		remove = 1;
-	else
-		return -EINVAL;
+	else {
+		count = -EINVAL;
+		goto out_put;
+	}
 
 	if (wait_on_bit_lock(&xprt->state, XPRT_LOCKED, TASK_KILLABLE)) {
 		count = -EINTR;
@@ -303,25 +307,28 @@
 		goto release_tasks;
 	}
 	if (offline) {
-		set_bit(XPRT_OFFLINE, &xprt->state);
-		spin_lock(&xps->xps_lock);
-		xps->xps_nactive--;
-		spin_unlock(&xps->xps_lock);
+		if (!test_and_set_bit(XPRT_OFFLINE, &xprt->state)) {
+			spin_lock(&xps->xps_lock);
+			xps->xps_nactive--;
+			spin_unlock(&xps->xps_lock);
+		}
 	} else if (online) {
-		clear_bit(XPRT_OFFLINE, &xprt->state);
-		spin_lock(&xps->xps_lock);
-		xps->xps_nactive++;
-		spin_unlock(&xps->xps_lock);
+		if (test_and_clear_bit(XPRT_OFFLINE, &xprt->state)) {
+			spin_lock(&xps->xps_lock);
+			xps->xps_nactive++;
+			spin_unlock(&xps->xps_lock);
+		}
 	} else if (remove) {
 		if (test_bit(XPRT_OFFLINE, &xprt->state)) {
-			set_bit(XPRT_REMOVE, &xprt->state);
-			xprt_force_disconnect(xprt);
-			if (test_bit(XPRT_CONNECTED, &xprt->state)) {
-				if (!xprt->sending.qlen &&
-				    !xprt->pending.qlen &&
-				    !xprt->backlog.qlen &&
-				    !atomic_long_read(&xprt->queuelen))
-					rpc_xprt_switch_remove_xprt(xps, xprt);
+			if (!test_and_set_bit(XPRT_REMOVE, &xprt->state)) {
+				xprt_force_disconnect(xprt);
+				if (test_bit(XPRT_CONNECTED, &xprt->state)) {
+					if (!xprt->sending.qlen &&
+					    !xprt->pending.qlen &&
+					    !xprt->backlog.qlen &&
+					    !atomic_long_read(&xprt->queuelen))
+						rpc_xprt_switch_remove_xprt(xps, xprt);
+				}
 			}
 		} else {
 			count = -EINVAL;
@@ -518,13 +525,16 @@
 			    struct net *net)
 {
 	struct rpc_sysfs_client *rpc_client;
+	struct rpc_sysfs_xprt_switch *xswitch =
+		(struct rpc_sysfs_xprt_switch *)xprt_switch->xps_sysfs;
+
+	if (!xswitch)
+		return;
 
 	rpc_client = rpc_sysfs_client_alloc(rpc_sunrpc_client_kobj,
 					    net, clnt->cl_clid);
 	if (rpc_client) {
 		char name[] = "switch";
-		struct rpc_sysfs_xprt_switch *xswitch =
-			(struct rpc_sysfs_xprt_switch *)xprt_switch->xps_sysfs;
 		int ret;
 
 		clnt->cl_sysfs = rpc_client;
@@ -558,6 +568,8 @@
 		rpc_xprt_switch->xprt_switch = xprt_switch;
 		rpc_xprt_switch->xprt = xprt;
 		kobject_uevent(&rpc_xprt_switch->kobject, KOBJ_ADD);
+	} else {
+		xprt_switch->xps_sysfs = NULL;
 	}
 }
 
@@ -569,6 +581,9 @@
 	struct rpc_sysfs_xprt_switch *switch_obj =
 		(struct rpc_sysfs_xprt_switch *)xprt_switch->xps_sysfs;
 
+	if (!switch_obj)
+		return;
+
 	rpc_xprt = rpc_sysfs_xprt_alloc(&switch_obj->kobject, xprt, gfp_flags);
 	if (rpc_xprt) {
 		xprt->xprt_sysfs = rpc_xprt;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xdr.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xdr.c
@@ -919,6 +919,28 @@
 EXPORT_SYMBOL_GPL(xdr_init_encode);
 
 /**
+ * xdr_init_encode_pages - Initialize an xdr_stream for encoding into pages
+ * @xdr: pointer to xdr_stream struct
+ * @buf: pointer to XDR buffer into which to encode data
+ * @pages: list of pages to decode into
+ * @rqst: pointer to controlling rpc_rqst, for debugging
+ *
+ */
+void xdr_init_encode_pages(struct xdr_stream *xdr, struct xdr_buf *buf,
+			   struct page **pages, struct rpc_rqst *rqst)
+{
+	xdr_reset_scratch_buffer(xdr);
+
+	xdr->buf = buf;
+	xdr->page_ptr = pages;
+	xdr->iov = NULL;
+	xdr->p = page_address(*pages);
+	xdr->end = (void *)xdr->p + min_t(u32, buf->buflen, PAGE_SIZE);
+	xdr->rqst = rqst;
+}
+EXPORT_SYMBOL_GPL(xdr_init_encode_pages);
+
+/**
  * xdr_commit_encode - Ensure all data is written to buffer
  * @xdr: pointer to xdr_stream
  *
@@ -979,7 +1001,11 @@
 	 */
 	xdr->p = (void *)p + frag2bytes;
 	space_left = xdr->buf->buflen - xdr->buf->len;
-	xdr->end = (void *)p + min_t(int, space_left, PAGE_SIZE);
+	if (space_left - frag1bytes >= PAGE_SIZE)
+		xdr->end = (void *)p + PAGE_SIZE;
+	else
+		xdr->end = (void *)p + space_left - frag1bytes;
+
 	xdr->buf->page_len += frag2bytes;
 	xdr->buf->len += nbytes;
 	return p;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprt.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprt.c
@@ -767,7 +767,8 @@
  */
 static void xprt_schedule_autoclose_locked(struct rpc_xprt *xprt)
 {
-	set_bit(XPRT_CLOSE_WAIT, &xprt->state);
+	if (test_and_set_bit(XPRT_CLOSE_WAIT, &xprt->state))
+		return;
 	if (test_and_set_bit(XPRT_LOCKED, &xprt->state) == 0)
 		queue_work(xprtiod_workqueue, &xprt->task_cleanup);
 	else if (xprt->snd_task && !test_bit(XPRT_SND_IS_COOKIE, &xprt->state))
@@ -928,12 +929,7 @@
 	if (!xprt_lock_write(xprt, task))
 		return;
 
-	if (test_and_clear_bit(XPRT_CLOSE_WAIT, &xprt->state)) {
-		trace_xprt_disconnect_cleanup(xprt);
-		xprt->ops->close(xprt);
-	}
-
-	if (!xprt_connected(xprt)) {
+	if (!xprt_connected(xprt) && !test_bit(XPRT_CLOSE_WAIT, &xprt->state)) {
 		task->tk_rqstp->rq_connect_cookie = xprt->connect_cookie;
 		rpc_sleep_on_timeout(&xprt->pending, task, NULL,
 				xprt_request_timeout(task->tk_rqstp));
@@ -1353,17 +1349,6 @@
 				INIT_LIST_HEAD(&req->rq_xmit2);
 				goto out;
 			}
-		} else if (RPC_IS_SWAPPER(task)) {
-			list_for_each_entry(pos, &xprt->xmit_queue, rq_xmit) {
-				if (pos->rq_cong || pos->rq_bytes_sent)
-					continue;
-				if (RPC_IS_SWAPPER(pos->rq_task))
-					continue;
-				/* Note: req is added _before_ pos */
-				list_add_tail(&req->rq_xmit, &pos->rq_xmit);
-				INIT_LIST_HEAD(&req->rq_xmit2);
-				goto out;
-			}
 		} else if (!req->rq_seqno) {
 			list_for_each_entry(pos, &xprt->xmit_queue, rq_xmit) {
 				if (pos->rq_task->tk_owner != task->tk_owner)
@@ -1603,15 +1588,14 @@
 {
 	struct rpc_rqst *next, *req = task->tk_rqstp;
 	struct rpc_xprt	*xprt = req->rq_xprt;
-	int counter, status;
+	int status;
 
 	spin_lock(&xprt->queue_lock);
-	counter = 0;
-	while (!list_empty(&xprt->xmit_queue)) {
-		if (++counter == 20)
+	for (;;) {
+		next = list_first_entry_or_null(&xprt->xmit_queue,
+						struct rpc_rqst, rq_xmit);
+		if (!next)
 			break;
-		next = list_first_entry(&xprt->xmit_queue,
-				struct rpc_rqst, rq_xmit);
 		xprt_pin_rqst(next);
 		spin_unlock(&xprt->queue_lock);
 		status = xprt_request_transmit(next, task);
@@ -1619,13 +1603,16 @@
 			status = 0;
 		spin_lock(&xprt->queue_lock);
 		xprt_unpin_rqst(next);
-		if (status == 0) {
-			if (!xprt_request_data_received(task) ||
-			    test_bit(RPC_TASK_NEED_XMIT, &task->tk_runstate))
-				continue;
-		} else if (test_bit(RPC_TASK_NEED_XMIT, &task->tk_runstate))
-			task->tk_status = status;
-		break;
+		if (status < 0) {
+			if (test_bit(RPC_TASK_NEED_XMIT, &task->tk_runstate))
+				task->tk_status = status;
+			break;
+		}
+		/* Was @task transmitted, and has it received a reply? */
+		if (xprt_request_data_received(task) &&
+		    !test_bit(RPC_TASK_NEED_XMIT, &task->tk_runstate))
+			break;
+		cond_resched_lock(&xprt->queue_lock);
 	}
 	spin_unlock(&xprt->queue_lock);
 }
@@ -1684,12 +1671,15 @@
 static struct rpc_rqst *xprt_dynamic_alloc_slot(struct rpc_xprt *xprt)
 {
 	struct rpc_rqst *req = ERR_PTR(-EAGAIN);
+	gfp_t gfp_mask = GFP_KERNEL;
 
 	if (xprt->num_reqs >= xprt->max_reqs)
 		goto out;
 	++xprt->num_reqs;
 	spin_unlock(&xprt->reserve_lock);
-	req = kzalloc(sizeof(struct rpc_rqst), GFP_NOFS);
+	if (current->flags & PF_WQ_WORKER)
+		gfp_mask |= __GFP_NORETRY | __GFP_NOWARN;
+	req = kzalloc(sizeof(*req), gfp_mask);
 	spin_lock(&xprt->reserve_lock);
 	if (req != NULL)
 		goto out;
@@ -2109,7 +2099,14 @@
 	 */
 	wait_on_bit_lock(&xprt->state, XPRT_LOCKED, TASK_UNINTERRUPTIBLE);
 
+	/*
+	 * xprt_schedule_autodisconnect() can run after XPRT_LOCKED
+	 * is cleared.  We use ->transport_lock to ensure the mod_timer()
+	 * can only run *before* del_time_sync(), never after.
+	 */
+	spin_lock(&xprt->transport_lock);
 	del_timer_sync(&xprt->timer);
+	spin_unlock(&xprt->transport_lock);
 
 	/*
 	 * Destroy sockets etc from the system workqueue so they can
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtmultipath.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtmultipath.c
@@ -288,8 +288,9 @@
 	return xprt_switch_find_current_entry(head, xpi->xpi_cursor);
 }
 
-bool rpc_xprt_switch_has_addr(struct rpc_xprt_switch *xps,
-			      const struct sockaddr *sap)
+static
+bool __rpc_xprt_switch_has_addr(struct rpc_xprt_switch *xps,
+				const struct sockaddr *sap)
 {
 	struct list_head *head;
 	struct rpc_xprt *pos;
@@ -308,6 +309,18 @@
 	return false;
 }
 
+bool rpc_xprt_switch_has_addr(struct rpc_xprt_switch *xps,
+			      const struct sockaddr *sap)
+{
+	bool res;
+
+	rcu_read_lock();
+	res = __rpc_xprt_switch_has_addr(xps, sap);
+	rcu_read_unlock();
+
+	return res;
+}
+
 static
 struct rpc_xprt *xprt_switch_find_next_entry(struct list_head *head,
 		const struct rpc_xprt *cur)
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/frwr_ops.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/frwr_ops.c
@@ -96,7 +96,8 @@
 	rpcrdma_mr_push(mr, &mr->mr_req->rl_free_mrs);
 }
 
-/* frwr_reset - Place MRs back on the free list
+/**
+ * frwr_reset - Place MRs back on @req's free list
  * @req: request to reset
  *
  * Used after a failed marshal. For FRWR, this means the MRs
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/rpc_rdma.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/rpc_rdma.c
@@ -1120,6 +1120,7 @@
 rpcrdma_is_bcall(struct rpcrdma_xprt *r_xprt, struct rpcrdma_rep *rep)
 #if defined(CONFIG_SUNRPC_BACKCHANNEL)
 {
+	struct rpc_xprt *xprt = &r_xprt->rx_xprt;
 	struct xdr_stream *xdr = &rep->rr_stream;
 	__be32 *p;
 
@@ -1143,6 +1144,10 @@
 	if (*p != cpu_to_be32(RPC_CALL))
 		return false;
 
+	/* No bc service. */
+	if (xprt->bc_serv == NULL)
+		return false;
+
 	/* Now that we are sure this is a backchannel call,
 	 * advance to the RPC header.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/svc_rdma.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/svc_rdma.c
@@ -212,24 +212,6 @@
 	{ },
 };
 
-static struct ctl_table svcrdma_table[] = {
-	{
-		.procname	= "svc_rdma",
-		.mode		= 0555,
-		.child		= svcrdma_parm_table
-	},
-	{ },
-};
-
-static struct ctl_table svcrdma_root_table[] = {
-	{
-		.procname	= "sunrpc",
-		.mode		= 0555,
-		.child		= svcrdma_table
-	},
-	{ },
-};
-
 static void svc_rdma_proc_cleanup(void)
 {
 	if (!svcrdma_table_header)
@@ -252,24 +234,34 @@
 
 	rc = percpu_counter_init(&svcrdma_stat_read, 0, GFP_KERNEL);
 	if (rc)
-		goto out_err;
+		goto err;
 	rc = percpu_counter_init(&svcrdma_stat_recv, 0, GFP_KERNEL);
 	if (rc)
-		goto out_err;
+		goto err_read;
 	rc = percpu_counter_init(&svcrdma_stat_sq_starve, 0, GFP_KERNEL);
 	if (rc)
-		goto out_err;
+		goto err_recv;
 	rc = percpu_counter_init(&svcrdma_stat_write, 0, GFP_KERNEL);
 	if (rc)
-		goto out_err;
+		goto err_sq;
+
+	svcrdma_table_header = register_sysctl("sunrpc/svc_rdma",
+					       svcrdma_parm_table);
+	if (!svcrdma_table_header)
+		goto err_write;
 
-	svcrdma_table_header = register_sysctl_table(svcrdma_root_table);
 	return 0;
 
-out_err:
+err_write:
+	rc = -ENOMEM;
+	percpu_counter_destroy(&svcrdma_stat_write);
+err_sq:
 	percpu_counter_destroy(&svcrdma_stat_sq_starve);
+err_recv:
 	percpu_counter_destroy(&svcrdma_stat_recv);
+err_read:
 	percpu_counter_destroy(&svcrdma_stat_read);
+err:
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
@@ -198,7 +198,7 @@
 
 	ret = rpcrdma_bc_send_request(rdma, rqst);
 	if (ret == -ENOTCONN)
-		svc_close_xprt(sxprt);
+		svc_xprt_close(sxprt);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/svc_rdma_recvfrom.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/svc_rdma_recvfrom.c
@@ -239,21 +239,20 @@
 }
 
 /**
- * svc_rdma_release_rqst - Release transport-specific per-rqst resources
- * @rqstp: svc_rqst being released
+ * svc_rdma_release_ctxt - Release transport-specific per-rqst resources
+ * @xprt: the transport which owned the context
+ * @vctxt: the context from rqstp->rq_xprt_ctxt or dr->xprt_ctxt
  *
  * Ensure that the recv_ctxt is released whether or not a Reply
  * was sent. For example, the client could close the connection,
  * or svc_process could drop an RPC, before the Reply is sent.
  */
-void svc_rdma_release_rqst(struct svc_rqst *rqstp)
+void svc_rdma_release_ctxt(struct svc_xprt *xprt, void *vctxt)
 {
-	struct svc_rdma_recv_ctxt *ctxt = rqstp->rq_xprt_ctxt;
-	struct svc_xprt *xprt = rqstp->rq_xprt;
+	struct svc_rdma_recv_ctxt *ctxt = vctxt;
 	struct svcxprt_rdma *rdma =
 		container_of(xprt, struct svcxprt_rdma, sc_xprt);
 
-	rqstp->rq_xprt_ctxt = NULL;
 	if (ctxt)
 		svc_rdma_recv_ctxt_put(rdma, ctxt);
 }
@@ -478,7 +477,13 @@
 	if (xdr_stream_decode_u32(&rctxt->rc_stream, &segcount))
 		return false;
 
-	/* A bogus segcount causes this buffer overflow check to fail. */
+	/* Before trusting the segcount value enough to use it in
+	 * a computation, perform a simple range check. This is an
+	 * arbitrary but sensible limit (ie, not architectural).
+	 */
+	if (unlikely(segcount > RPCSVC_MAXPAGES))
+		return false;
+
 	p = xdr_inline_decode(&rctxt->rc_stream,
 			      segcount * rpcrdma_segment_maxsz * sizeof(*p));
 	return p != NULL;
@@ -792,6 +797,12 @@
 	struct svc_rdma_recv_ctxt *ctxt;
 	int ret;
 
+	/* Prevent svc_xprt_release() from releasing pages in rq_pages
+	 * when returning 0 or an error.
+	 */
+	rqstp->rq_respages = rqstp->rq_pages;
+	rqstp->rq_next_page = rqstp->rq_respages;
+
 	rqstp->rq_xprt_ctxt = NULL;
 
 	ctxt = NULL;
@@ -815,18 +826,11 @@
 				   DMA_FROM_DEVICE);
 	svc_rdma_build_arg_xdr(rqstp, ctxt);
 
-	/* Prevent svc_xprt_release from releasing pages in rq_pages
-	 * if we return 0 or an error.
-	 */
-	rqstp->rq_respages = rqstp->rq_pages;
-	rqstp->rq_next_page = rqstp->rq_respages;
-
 	ret = svc_rdma_xdr_decode_req(&rqstp->rq_arg, ctxt);
 	if (ret < 0)
 		goto out_err;
 	if (ret == 0)
 		goto out_drop;
-	rqstp->rq_xprt_hlen = ret;
 
 	if (svc_rdma_is_reverse_direction_reply(xprt, ctxt))
 		goto out_backchannel;
@@ -854,7 +858,8 @@
 	if (ret == -EINVAL)
 		svc_rdma_send_error(rdma_xprt, ctxt, ret);
 	svc_rdma_recv_ctxt_put(rdma_xprt, ctxt);
-	return ret;
+	svc_xprt_deferred_close(xprt);
+	return -ENOTCONN;
 
 out_backchannel:
 	svc_rdma_handle_bc_reply(rqstp, ctxt);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/svc_rdma_rw.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/svc_rdma_rw.c
@@ -456,10 +456,10 @@
 		unsigned int write_len;
 		u64 offset;
 
-		seg = &info->wi_chunk->ch_segments[info->wi_seg_no];
-		if (!seg)
+		if (info->wi_seg_no >= info->wi_chunk->ch_segcount)
 			goto out_overflow;
 
+		seg = &info->wi_chunk->ch_segments[info->wi_seg_no];
 		write_len = min(remaining, seg->rs_length - info->wi_seg_off);
 		if (!write_len)
 			goto out_overflow;
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/svc_rdma_transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/svc_rdma_transport.c
@@ -81,7 +81,7 @@
 	.xpo_recvfrom = svc_rdma_recvfrom,
 	.xpo_sendto = svc_rdma_sendto,
 	.xpo_result_payload = svc_rdma_result_payload,
-	.xpo_release_rqst = svc_rdma_release_rqst,
+	.xpo_release_ctxt = svc_rdma_release_ctxt,
 	.xpo_detach = svc_rdma_detach,
 	.xpo_free = svc_rdma_free,
 	.xpo_has_wspace = svc_rdma_has_wspace,
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/transport.c
@@ -521,7 +521,7 @@
 	return;
 
 out_sleep:
-	task->tk_status = -EAGAIN;
+	task->tk_status = -ENOMEM;
 	xprt_add_backlog(xprt, task);
 }
 
@@ -574,8 +574,10 @@
 	gfp_t flags;
 
 	flags = RPCRDMA_DEF_GFP;
+	if (RPC_IS_ASYNC(task))
+		flags = GFP_NOWAIT | __GFP_NOWARN;
 	if (RPC_IS_SWAPPER(task))
-		flags = __GFP_MEMALLOC | GFP_NOWAIT | __GFP_NOWARN;
+		flags |= __GFP_MEMALLOC;
 
 	if (!rpcrdma_check_regbuf(r_xprt, req->rl_sendbuf, rqst->rq_callsize,
 				  flags))
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtrdma/verbs.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtrdma/verbs.c
@@ -258,7 +258,11 @@
 	case RDMA_CM_EVENT_DEVICE_REMOVAL:
 		pr_info("rpcrdma: removing device %s for %pISpc\n",
 			ep->re_id->device->name, sap);
-		fallthrough;
+		switch (xchg(&ep->re_connect_status, -ENODEV)) {
+		case 0: goto wake_connect_worker;
+		case 1: goto disconnected;
+		}
+		return 0;
 	case RDMA_CM_EVENT_ADDR_CHANGE:
 		ep->re_connect_status = -ENODEV;
 		goto disconnected;
@@ -438,6 +442,7 @@
 					      IB_POLL_WORKQUEUE);
 	if (IS_ERR(ep->re_attr.send_cq)) {
 		rc = PTR_ERR(ep->re_attr.send_cq);
+		ep->re_attr.send_cq = NULL;
 		goto out_destroy;
 	}
 
@@ -446,6 +451,7 @@
 					      IB_POLL_WORKQUEUE);
 	if (IS_ERR(ep->re_attr.recv_cq)) {
 		rc = PTR_ERR(ep->re_attr.recv_cq);
+		ep->re_attr.recv_cq = NULL;
 		goto out_destroy;
 	}
 	ep->re_receive_count = 0;
@@ -484,6 +490,7 @@
 	ep->re_pd = ib_alloc_pd(device, 0);
 	if (IS_ERR(ep->re_pd)) {
 		rc = PTR_ERR(ep->re_pd);
+		ep->re_pd = NULL;
 		goto out_destroy;
 	}
 
@@ -855,7 +862,7 @@
 	return req;
 
 out3:
-	kfree(req->rl_sendbuf);
+	rpcrdma_regbuf_free(req->rl_sendbuf);
 out2:
 	kfree(req);
 out1:
@@ -917,6 +924,8 @@
 
 static void rpcrdma_req_reset(struct rpcrdma_req *req)
 {
+	struct rpcrdma_mr *mr;
+
 	/* Credits are valid for only one connection */
 	req->rl_slot.rq_cong = 0;
 
@@ -926,7 +935,19 @@
 	rpcrdma_regbuf_dma_unmap(req->rl_sendbuf);
 	rpcrdma_regbuf_dma_unmap(req->rl_recvbuf);
 
-	frwr_reset(req);
+	/* The verbs consumer can't know the state of an MR on the
+	 * req->rl_registered list unless a successful completion
+	 * has occurred, so they cannot be re-used.
+	 */
+	while ((mr = rpcrdma_mr_pop(&req->rl_registered))) {
+		struct rpcrdma_buffer *buf = &mr->mr_xprt->rx_buf;
+
+		spin_lock(&buf->rb_lock);
+		list_del(&mr->mr_all);
+		spin_unlock(&buf->rb_lock);
+
+		frwr_mr_release(mr);
+	}
 }
 
 /* ASSUMPTION: the rb_allreqs list is stable for the duration,
@@ -959,9 +980,6 @@
 	if (!rep->rr_rdmabuf)
 		goto out_free;
 
-	if (!rpcrdma_regbuf_dma_map(r_xprt, rep->rr_rdmabuf))
-		goto out_free_regbuf;
-
 	rep->rr_cid.ci_completion_id =
 		atomic_inc_return(&r_xprt->rx_ep->re_completion_ids);
 
@@ -980,8 +998,6 @@
 	spin_unlock(&buf->rb_lock);
 	return rep;
 
-out_free_regbuf:
-	rpcrdma_regbuf_free(rep->rr_rdmabuf);
 out_free:
 	kfree(rep);
 out:
@@ -1388,6 +1404,10 @@
 			rep = rpcrdma_rep_create(r_xprt, temp);
 		if (!rep)
 			break;
+		if (!rpcrdma_regbuf_dma_map(r_xprt, rep->rr_rdmabuf)) {
+			rpcrdma_rep_put(buf, rep);
+			break;
+		}
 
 		rep->rr_cid.ci_queue_id = ep->re_attr.recv_cq->res.id;
 		trace_xprtrdma_post_recv(rep);
--- linux-xilinx-zynqmp-5.15.0.orig/net/sunrpc/xprtsock.c
+++ linux-xilinx-zynqmp-5.15.0/net/sunrpc/xprtsock.c
@@ -763,12 +763,12 @@
 /**
  * xs_nospace - handle transmit was incomplete
  * @req: pointer to RPC request
+ * @transport: pointer to struct sock_xprt
  *
  */
-static int xs_nospace(struct rpc_rqst *req)
+static int xs_nospace(struct rpc_rqst *req, struct sock_xprt *transport)
 {
-	struct rpc_xprt *xprt = req->rq_xprt;
-	struct sock_xprt *transport = container_of(xprt, struct sock_xprt, xprt);
+	struct rpc_xprt *xprt = &transport->xprt;
 	struct sock *sk = transport->inet;
 	int ret = -EAGAIN;
 
@@ -780,24 +780,42 @@
 	/* Don't race with disconnect */
 	if (xprt_connected(xprt)) {
 		/* wait for more buffer space */
+		set_bit(XPRT_SOCK_NOSPACE, &transport->sock_state);
+		set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
 		sk->sk_write_pending++;
 		xprt_wait_for_buffer_space(xprt);
 	} else
 		ret = -ENOTCONN;
 
 	spin_unlock(&xprt->transport_lock);
+	return ret;
+}
 
-	/* Race breaker in case memory is freed before above code is called */
-	if (ret == -EAGAIN) {
-		struct socket_wq *wq;
-
-		rcu_read_lock();
-		wq = rcu_dereference(sk->sk_wq);
-		set_bit(SOCKWQ_ASYNC_NOSPACE, &wq->flags);
-		rcu_read_unlock();
+static int xs_sock_nospace(struct rpc_rqst *req)
+{
+	struct sock_xprt *transport =
+		container_of(req->rq_xprt, struct sock_xprt, xprt);
+	struct sock *sk = transport->inet;
+	int ret = -EAGAIN;
 
-		sk->sk_write_space(sk);
-	}
+	lock_sock(sk);
+	if (!sock_writeable(sk))
+		ret = xs_nospace(req, transport);
+	release_sock(sk);
+	return ret;
+}
+
+static int xs_stream_nospace(struct rpc_rqst *req)
+{
+	struct sock_xprt *transport =
+		container_of(req->rq_xprt, struct sock_xprt, xprt);
+	struct sock *sk = transport->inet;
+	int ret = -EAGAIN;
+
+	lock_sock(sk);
+	if (!sk_stream_memory_free(sk))
+		ret = xs_nospace(req, transport);
+	release_sock(sk);
 	return ret;
 }
 
@@ -856,7 +874,7 @@
 
 	/* Close the stream if the previous transmission was incomplete */
 	if (xs_send_request_was_aborted(transport, req)) {
-		xs_close(xprt);
+		xprt_force_disconnect(xprt);
 		return -ENOTCONN;
 	}
 
@@ -887,14 +905,14 @@
 	case -ENOBUFS:
 		break;
 	case -EAGAIN:
-		status = xs_nospace(req);
+		status = xs_stream_nospace(req);
 		break;
 	default:
 		dprintk("RPC:       sendmsg returned unrecognized error %d\n",
 			-status);
 		fallthrough;
 	case -EPIPE:
-		xs_close(xprt);
+		xprt_force_disconnect(xprt);
 		status = -ENOTCONN;
 	}
 
@@ -963,7 +981,7 @@
 		/* Should we call xs_close() here? */
 		break;
 	case -EAGAIN:
-		status = xs_nospace(req);
+		status = xs_sock_nospace(req);
 		break;
 	case -ENETUNREACH:
 	case -ENOBUFS:
@@ -1083,7 +1101,7 @@
 		/* Should we call xs_close() here? */
 		break;
 	case -EAGAIN:
-		status = xs_nospace(req);
+		status = xs_stream_nospace(req);
 		break;
 	case -ECONNRESET:
 	case -ECONNREFUSED:
@@ -1124,6 +1142,8 @@
 	clear_bit(XPRT_SOCK_WAKE_ERROR, &transport->sock_state);
 	clear_bit(XPRT_SOCK_WAKE_WRITE, &transport->sock_state);
 	clear_bit(XPRT_SOCK_WAKE_DISCONNECT, &transport->sock_state);
+	clear_bit(XPRT_SOCK_NOSPACE, &transport->sock_state);
+	clear_bit(XPRT_SOCK_UPD_TIMEOUT, &transport->sock_state);
 }
 
 static void xs_run_error_worker(struct sock_xprt *transport, unsigned int nr)
@@ -1181,6 +1201,16 @@
 
 	if (sk == NULL)
 		return;
+	/*
+	 * Make sure we're calling this in a context from which it is safe
+	 * to call __fput_sync(). In practice that means rpciod and the
+	 * system workqueue.
+	 */
+	if (!(current->flags & PF_WQ_WORKER)) {
+		WARN_ON_ONCE(1);
+		set_bit(XPRT_CLOSE_WAIT, &xprt->state);
+		return;
+	}
 
 	if (atomic_read(&transport->xprt.swapper))
 		sk_clear_memalloc(sk);
@@ -1204,7 +1234,7 @@
 	mutex_unlock(&transport->recv_mutex);
 
 	trace_rpc_socket_close(xprt, sock);
-	fput(filp);
+	__fput_sync(filp);
 
 	xprt_disconnect_done(xprt);
 }
@@ -1477,7 +1507,6 @@
 
 static void xs_write_space(struct sock *sk)
 {
-	struct socket_wq *wq;
 	struct sock_xprt *transport;
 	struct rpc_xprt *xprt;
 
@@ -1488,15 +1517,10 @@
 	if (unlikely(!(xprt = xprt_from_sock(sk))))
 		return;
 	transport = container_of(xprt, struct sock_xprt, xprt);
-	rcu_read_lock();
-	wq = rcu_dereference(sk->sk_wq);
-	if (!wq || test_and_clear_bit(SOCKWQ_ASYNC_NOSPACE, &wq->flags) == 0)
-		goto out;
-
+	if (!test_and_clear_bit(XPRT_SOCK_NOSPACE, &transport->sock_state))
+		return;
 	xs_run_error_worker(transport, XPRT_SOCK_WAKE_WRITE);
 	sk->sk_write_pending--;
-out:
-	rcu_read_unlock();
 }
 
 /**
@@ -1814,6 +1838,12 @@
 		goto out;
 	}
 
+	if (protocol == IPPROTO_TCP) {
+		sock->sk->sk_net_refcnt = 1;
+		get_net(xprt->xprt_net);
+		sock_inuse_add(xprt->xprt_net, 1);
+	}
+
 	filp = sock_alloc_file(sock, O_NONBLOCK, NULL);
 	if (IS_ERR(filp))
 		return ERR_CAST(filp);
@@ -1840,7 +1870,6 @@
 		sk->sk_user_data = xprt;
 		sk->sk_data_ready = xs_data_ready;
 		sk->sk_write_space = xs_udp_write_space;
-		sock_set_flag(sk, SOCK_FASYNC);
 		sk->sk_error_report = xs_error_report;
 
 		xprt_clear_connected(xprt);
@@ -1925,6 +1954,9 @@
 	struct sock_xprt *transport = container_of(xprt, struct sock_xprt, xprt);
 	int ret;
 
+	if (transport->file)
+		goto force_disconnect;
+
 	 if (RPC_IS_ASYNC(task)) {
 		/*
 		 * We want the AF_LOCAL connect to be resolved in the
@@ -1937,11 +1969,17 @@
 		 */
 		task->tk_rpc_status = -ENOTCONN;
 		rpc_exit(task, -ENOTCONN);
-		return;
+		goto out_wake;
 	}
 	ret = xs_local_setup_socket(transport);
 	if (ret && !RPC_IS_SOFTCONN(task))
 		msleep_interruptible(15000);
+	return;
+force_disconnect:
+	xprt_force_disconnect(xprt);
+out_wake:
+	xprt_clear_connecting(xprt);
+	xprt_wake_pending_tasks(xprt, -ENOTCONN);
 }
 
 #if IS_ENABLED(CONFIG_SUNRPC_SWAP)
@@ -2038,7 +2076,6 @@
 		sk->sk_user_data = xprt;
 		sk->sk_data_ready = xs_data_ready;
 		sk->sk_write_space = xs_udp_write_space;
-		sock_set_flag(sk, SOCK_FASYNC);
 
 		xprt_set_connected(xprt);
 
@@ -2106,6 +2143,7 @@
 	switch (skst) {
 	case TCP_FIN_WAIT1:
 	case TCP_FIN_WAIT2:
+	case TCP_LAST_ACK:
 		break;
 	case TCP_ESTABLISHED:
 	case TCP_CLOSE_WAIT:
@@ -2202,7 +2240,6 @@
 		sk->sk_data_ready = xs_data_ready;
 		sk->sk_state_change = xs_tcp_state_change;
 		sk->sk_write_space = xs_tcp_write_space;
-		sock_set_flag(sk, SOCK_FASYNC);
 		sk->sk_error_report = xs_error_report;
 
 		/* socket options */
@@ -2233,6 +2270,7 @@
 		fallthrough;
 	case -EINPROGRESS:
 		/* SYN_SENT! */
+		set_bit(XPRT_SOCK_CONNECT_SENT, &transport->sock_state);
 		if (xprt->reestablish_timeout < XS_TCP_INIT_REEST_TO)
 			xprt->reestablish_timeout = XS_TCP_INIT_REEST_TO;
 		break;
@@ -2258,10 +2296,14 @@
 	struct rpc_xprt *xprt = &transport->xprt;
 	int status = -EIO;
 
-	if (!sock) {
-		sock = xs_create_sock(xprt, transport,
-				xs_addr(xprt)->sa_family, SOCK_STREAM,
-				IPPROTO_TCP, true);
+	if (xprt_connected(xprt))
+		goto out;
+	if (test_and_clear_bit(XPRT_SOCK_CONNECT_SENT,
+			       &transport->sock_state) ||
+	    !sock) {
+		xs_reset_transport(transport);
+		sock = xs_create_sock(xprt, transport, xs_addr(xprt)->sa_family,
+				      SOCK_STREAM, IPPROTO_TCP, true);
 		if (IS_ERR(sock)) {
 			status = PTR_ERR(sock);
 			goto out;
@@ -2295,6 +2337,13 @@
 	case -EALREADY:
 		xprt_unlock_connect(xprt, transport);
 		return;
+	case -EPERM:
+		/* Happens, for instance, if a BPF program is preventing
+		 * the connect. Remap the error so upper layers can better
+		 * deal with it.
+		 */
+		status = -ECONNREFUSED;
+		fallthrough;
 	case -EINVAL:
 		/* Happens, for instance, if the user specified a link
 		 * local IPv6 address without a scope-id.
@@ -2343,11 +2392,7 @@
 
 	if (transport->sock != NULL) {
 		dprintk("RPC:       xs_connect delayed xprt %p for %lu "
-				"seconds\n",
-				xprt, xprt->reestablish_timeout / HZ);
-
-		/* Start by resetting any existing state */
-		xs_reset_transport(transport);
+			"seconds\n", xprt, xprt->reestablish_timeout / HZ);
 
 		delay = xprt_reconnect_delay(xprt);
 		xprt_reconnect_backoff(xprt, XS_TCP_INIT_REEST_TO);
@@ -2823,9 +2868,6 @@
 		}
 		xprt_set_bound(xprt);
 		xs_format_peer_addresses(xprt, "local", RPCBIND_NETID_LOCAL);
-		ret = ERR_PTR(xs_local_setup_socket(transport));
-		if (ret)
-			goto out_err;
 		break;
 	default:
 		ret = ERR_PTR(-EAFNOSUPPORT);
--- linux-xilinx-zynqmp-5.15.0.orig/net/switchdev/switchdev.c
+++ linux-xilinx-zynqmp-5.15.0/net/switchdev/switchdev.c
@@ -19,6 +19,34 @@
 #include <linux/rtnetlink.h>
 #include <net/switchdev.h>
 
+static bool switchdev_obj_eq(const struct switchdev_obj *a,
+			     const struct switchdev_obj *b)
+{
+	const struct switchdev_obj_port_vlan *va, *vb;
+	const struct switchdev_obj_port_mdb *ma, *mb;
+
+	if (a->id != b->id || a->orig_dev != b->orig_dev)
+		return false;
+
+	switch (a->id) {
+	case SWITCHDEV_OBJ_ID_PORT_VLAN:
+		va = SWITCHDEV_OBJ_PORT_VLAN(a);
+		vb = SWITCHDEV_OBJ_PORT_VLAN(b);
+		return va->flags == vb->flags &&
+			va->vid == vb->vid;
+	case SWITCHDEV_OBJ_ID_PORT_MDB:
+	case SWITCHDEV_OBJ_ID_HOST_MDB:
+		ma = SWITCHDEV_OBJ_PORT_MDB(a);
+		mb = SWITCHDEV_OBJ_PORT_MDB(b);
+		return ma->vid == mb->vid &&
+			ether_addr_equal(ma->addr, mb->addr);
+	default:
+		break;
+	}
+
+	BUG();
+}
+
 static LIST_HEAD(deferred);
 static DEFINE_SPINLOCK(deferred_lock);
 
@@ -306,6 +334,50 @@
 }
 EXPORT_SYMBOL_GPL(switchdev_port_obj_del);
 
+/**
+ *	switchdev_port_obj_act_is_deferred - Is object action pending?
+ *
+ *	@dev: port device
+ *	@nt: type of action; add or delete
+ *	@obj: object to test
+ *
+ *	Returns true if a deferred item is pending, which is
+ *	equivalent to the action @nt on an object @obj.
+ *
+ *	rtnl_lock must be held.
+ */
+bool switchdev_port_obj_act_is_deferred(struct net_device *dev,
+					enum switchdev_notifier_type nt,
+					const struct switchdev_obj *obj)
+{
+	struct switchdev_deferred_item *dfitem;
+	bool found = false;
+
+	ASSERT_RTNL();
+
+	spin_lock_bh(&deferred_lock);
+
+	list_for_each_entry(dfitem, &deferred, list) {
+		if (dfitem->dev != dev)
+			continue;
+
+		if ((dfitem->func == switchdev_port_obj_add_deferred &&
+		     nt == SWITCHDEV_PORT_OBJ_ADD) ||
+		    (dfitem->func == switchdev_port_obj_del_deferred &&
+		     nt == SWITCHDEV_PORT_OBJ_DEL)) {
+			if (switchdev_obj_eq((const void *)dfitem->data, obj)) {
+				found = true;
+				break;
+			}
+		}
+	}
+
+	spin_unlock_bh(&deferred_lock);
+
+	return found;
+}
+EXPORT_SYMBOL_GPL(switchdev_port_obj_act_is_deferred);
+
 static ATOMIC_NOTIFIER_HEAD(switchdev_notif_chain);
 static BLOCKING_NOTIFIER_HEAD(switchdev_blocking_notif_chain);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/bcast.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/bcast.c
@@ -320,8 +320,8 @@
 {
 	struct tipc_msg *hdr, *_hdr;
 	struct sk_buff_head tmpq;
+	u16 cong_link_cnt = 0;
 	struct sk_buff *_skb;
-	u16 cong_link_cnt;
 	int rc = 0;
 
 	/* Is a cluster supporting with new capabilities ? */
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/bearer.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/bearer.c
@@ -163,8 +163,12 @@
 
 	/* return bearer name components, if necessary */
 	if (name_parts) {
-		strcpy(name_parts->media_name, media_name);
-		strcpy(name_parts->if_name, if_name);
+		if (strscpy(name_parts->media_name, media_name,
+			    TIPC_MAX_MEDIA_NAME) < 0)
+			return 0;
+		if (strscpy(name_parts->if_name, if_name,
+			    TIPC_MAX_IF_NAME) < 0)
+			return 0;
 	}
 	return 1;
 }
@@ -259,9 +263,8 @@
 	u32 i;
 
 	if (!bearer_name_validate(name, &b_names)) {
-		errstr = "illegal name";
 		NL_SET_ERR_MSG(extack, "Illegal name");
-		goto rejected;
+		return res;
 	}
 
 	if (prio > TIPC_MAX_LINK_PRI && prio != TIPC_MEDIA_LINK_PRI) {
@@ -352,16 +355,18 @@
 		goto rejected;
 	}
 
-	test_and_set_bit_lock(0, &b->up);
-	rcu_assign_pointer(tn->bearer_list[bearer_id], b);
-	if (skb)
-		tipc_bearer_xmit_skb(net, bearer_id, skb, &b->bcast_addr);
-
+	/* Create monitoring data before accepting activate messages */
 	if (tipc_mon_create(net, bearer_id)) {
 		bearer_disable(net, b);
+		kfree_skb(skb);
 		return -ENOMEM;
 	}
 
+	test_and_set_bit_lock(0, &b->up);
+	rcu_assign_pointer(tn->bearer_list[bearer_id], b);
+	if (skb)
+		tipc_bearer_xmit_skb(net, bearer_id, skb, &b->bcast_addr);
+
 	pr_info("Enabled bearer <%s>, priority %u\n", name, prio);
 
 	return res;
@@ -540,6 +545,19 @@
 	return mtu;
 }
 
+int tipc_bearer_min_mtu(struct net *net, u32 bearer_id)
+{
+	int mtu = TIPC_MIN_BEARER_MTU;
+	struct tipc_bearer *b;
+
+	rcu_read_lock();
+	b = bearer_get(net, bearer_id);
+	if (b)
+		mtu += b->encap_hlen;
+	rcu_read_unlock();
+	return mtu;
+}
+
 /* tipc_bearer_xmit_skb - sends buffer to destination over bearer
  */
 void tipc_bearer_xmit_skb(struct net *net, u32 bearer_id,
@@ -1074,6 +1092,12 @@
 
 #ifdef CONFIG_TIPC_MEDIA_UDP
 	if (attrs[TIPC_NLA_BEARER_UDP_OPTS]) {
+		if (b->media->type_id != TIPC_MEDIA_TYPE_UDP) {
+			rtnl_unlock();
+			NL_SET_ERR_MSG(info->extack, "UDP option is unsupported");
+			return -EINVAL;
+		}
+
 		err = tipc_udp_nl_bearer_add(b,
 					     attrs[TIPC_NLA_BEARER_UDP_OPTS]);
 		if (err) {
@@ -1137,8 +1161,8 @@
 				return -EINVAL;
 			}
 #ifdef CONFIG_TIPC_MEDIA_UDP
-			if (tipc_udp_mtu_bad(nla_get_u32
-					     (props[TIPC_NLA_PROP_MTU]))) {
+			if (nla_get_u32(props[TIPC_NLA_PROP_MTU]) <
+			    b->encap_hlen + TIPC_MIN_BEARER_MTU) {
 				NL_SET_ERR_MSG(info->extack,
 					       "MTU value is out-of-range");
 				return -EINVAL;
@@ -1244,7 +1268,7 @@
 	struct tipc_nl_msg msg;
 	struct tipc_media *media;
 	struct sk_buff *rep;
-	struct nlattr *attrs[TIPC_NLA_BEARER_MAX + 1];
+	struct nlattr *attrs[TIPC_NLA_MEDIA_MAX + 1];
 
 	if (!info->attrs[TIPC_NLA_MEDIA])
 		return -EINVAL;
@@ -1293,7 +1317,7 @@
 	int err;
 	char *name;
 	struct tipc_media *m;
-	struct nlattr *attrs[TIPC_NLA_BEARER_MAX + 1];
+	struct nlattr *attrs[TIPC_NLA_MEDIA_MAX + 1];
 
 	if (!info->attrs[TIPC_NLA_MEDIA])
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/bearer.h
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/bearer.h
@@ -146,6 +146,7 @@
  * @identity: array index of this bearer within TIPC bearer array
  * @disc: ptr to link setup request
  * @net_plane: network plane ('A' through 'H') currently associated with bearer
+ * @encap_hlen: encap headers length
  * @up: bearer up flag (bit 0)
  * @refcnt: tipc_bearer reference counter
  *
@@ -170,6 +171,7 @@
 	u32 identity;
 	struct tipc_discoverer *disc;
 	char net_plane;
+	u16 encap_hlen;
 	unsigned long up;
 	refcount_t refcnt;
 };
@@ -232,6 +234,7 @@
 void tipc_bearer_cleanup(void);
 void tipc_bearer_stop(struct net *net);
 int tipc_bearer_mtu(struct net *net, u32 bearer_id);
+int tipc_bearer_min_mtu(struct net *net, u32 bearer_id);
 bool tipc_bearer_bcast_support(struct net *net, u32 bearer_id);
 void tipc_bearer_xmit_skb(struct net *net, u32 bearer_id,
 			  struct sk_buff *skb,
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/core.c
@@ -109,10 +109,9 @@
 	struct tipc_net *tn = tipc_net(net);
 
 	tipc_detach_loopback(net);
+	tipc_net_stop(net);
 	/* Make sure the tipc_net_finalize_work() finished */
 	cancel_work_sync(&tn->work);
-	tipc_net_stop(net);
-
 	tipc_bcast_stop(net);
 	tipc_nametbl_stop(net);
 	tipc_sk_rht_destroy(net);
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/crypto.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/crypto.c
@@ -597,6 +597,10 @@
 	tmp->cloned = NULL;
 	tmp->authsize = TIPC_AES_GCM_TAG_SIZE;
 	tmp->key = kmemdup(ukey, tipc_aead_key_size(ukey), GFP_KERNEL);
+	if (!tmp->key) {
+		tipc_aead_free(&tmp->rcu);
+		return -ENOMEM;
+	}
 	memcpy(&tmp->salt, ukey->key + keylen, TIPC_AES_GCM_SALT_SIZE);
 	atomic_set(&tmp->users, 0);
 	atomic64_set(&tmp->seqno, 0);
@@ -1448,14 +1452,14 @@
 	struct tipc_crypto *tx = tipc_net(net)->crypto_tx;
 	struct tipc_key key;
 
-	spin_lock(&tx->lock);
+	spin_lock_bh(&tx->lock);
 	key = tx->key;
 	WARN_ON(!key.active || tx_key != key.active);
 
 	/* Free the active key */
 	tipc_crypto_key_set_state(tx, key.passive, 0, key.pending);
 	tipc_crypto_key_detach(tx->aead[key.active], &tx->lock);
-	spin_unlock(&tx->lock);
+	spin_unlock_bh(&tx->lock);
 
 	pr_warn("%s: key is revoked\n", tx->name);
 	return -EKEYREVOKED;
@@ -1967,7 +1971,8 @@
 
 	skb_reset_network_header(*skb);
 	skb_pull(*skb, tipc_ehdr_size(ehdr));
-	pskb_trim(*skb, (*skb)->len - aead->authsize);
+	if (pskb_trim(*skb, (*skb)->len - aead->authsize))
+		goto free_skb;
 
 	/* Validate TIPCv2 message */
 	if (unlikely(!tipc_msg_validate(skb))) {
@@ -1978,6 +1983,9 @@
 	/* Ok, everything's fine, try to synch own keys according to peers' */
 	tipc_crypto_key_synch(rx, *skb);
 
+	/* Re-fetch skb cb as skb might be changed in tipc_msg_validate */
+	skb_cb = TIPC_SKB_CB(*skb);
+
 	/* Mark skb decrypted */
 	skb_cb->decrypted = 1;
 
@@ -2283,7 +2291,7 @@
 	struct tipc_crypto *tx = tipc_net(rx->net)->crypto_tx;
 	struct tipc_aead_key *skey = NULL;
 	u16 key_gen = msg_key_gen(hdr);
-	u16 size = msg_data_sz(hdr);
+	u32 size = msg_data_sz(hdr);
 	u8 *data = msg_data(hdr);
 	unsigned int keylen;
 
@@ -2296,8 +2304,8 @@
 	keylen = ntohl(*((__be32 *)(data + TIPC_AEAD_ALG_NAME)));
 
 	/* Verify the supplied size values */
-	if (unlikely(size != keylen + sizeof(struct tipc_aead_key) ||
-		     keylen > TIPC_AEAD_KEY_SIZE_MAX)) {
+	if (unlikely(keylen > TIPC_AEAD_KEY_SIZE_MAX ||
+		     size != keylen + sizeof(struct tipc_aead_key))) {
 		pr_debug("%s: invalid MSG_CRYPTO key size\n", rx->name);
 		goto exit;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/discover.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/discover.c
@@ -148,8 +148,8 @@
 {
 	struct net *net = d->net;
 	struct tipc_net *tn = tipc_net(net);
-	bool trial = time_before(jiffies, tn->addr_trial_end);
 	u32 self = tipc_own_addr(net);
+	bool trial = time_before(jiffies, tn->addr_trial_end) && !self;
 
 	if (mtyp == DSC_TRIAL_FAIL_MSG) {
 		if (!trial)
@@ -211,7 +211,10 @@
 	u32 self;
 	int err;
 
-	skb_linearize(skb);
+	if (skb_linearize(skb)) {
+		kfree_skb(skb);
+		return;
+	}
 	hdr = buf_msg(skb);
 
 	if (caps & TIPC_NODE_ID128)
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/link.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/link.c
@@ -1298,8 +1298,11 @@
 		return false;
 #ifdef CONFIG_TIPC_CRYPTO
 	case MSG_CRYPTO:
-		tipc_crypto_msg_rcv(l->net, skb);
-		return true;
+		if (TIPC_SKB_CB(skb)->decrypted) {
+			tipc_crypto_msg_rcv(l->net, skb);
+			return true;
+		}
+		fallthrough;
 #endif
 	default:
 		pr_warn("Dropping received illegal msg type\n");
@@ -1442,7 +1445,7 @@
 		p = (struct tipc_gap_ack_blks *)msg_data(hdr);
 		sz = ntohs(p->len);
 		/* Sanity check */
-		if (sz == struct_size(p, gacks, p->ugack_cnt + p->bgack_cnt)) {
+		if (sz == struct_size(p, gacks, size_add(p->ugack_cnt, p->bgack_cnt))) {
 			/* Good, check if the desired type exists */
 			if ((uc && p->ugack_cnt) || (!uc && p->bgack_cnt))
 				goto ok;
@@ -1529,7 +1532,7 @@
 			__tipc_build_gap_ack_blks(ga, l, ga->bgack_cnt) : 0;
 
 	/* Total len */
-	len = struct_size(ga, gacks, ga->bgack_cnt + ga->ugack_cnt);
+	len = struct_size(ga, gacks, size_add(ga->bgack_cnt, ga->ugack_cnt));
 	ga->len = htons(len);
 	return len;
 }
@@ -2196,7 +2199,7 @@
 	struct tipc_msg *hdr = buf_msg(skb);
 	struct tipc_gap_ack_blks *ga = NULL;
 	bool reply = msg_probe(hdr), retransmitted = false;
-	u16 dlen = msg_data_sz(hdr), glen = 0;
+	u32 dlen = msg_data_sz(hdr), glen = 0, msg_max;
 	u16 peers_snd_nxt =  msg_next_sent(hdr);
 	u16 peers_tol = msg_link_tolerance(hdr);
 	u16 peers_prio = msg_linkprio(hdr);
@@ -2210,13 +2213,19 @@
 	void *data;
 
 	trace_tipc_proto_rcv(skb, false, l->name);
+
+	if (dlen > U16_MAX)
+		goto exit;
+
 	if (tipc_link_is_blocked(l) || !xmitq)
 		goto exit;
 
 	if (tipc_own_addr(l->net) > msg_prevnode(hdr))
 		l->net_plane = msg_net_plane(hdr);
 
-	skb_linearize(skb);
+	if (skb_linearize(skb))
+		goto exit;
+
 	hdr = buf_msg(skb);
 	data = msg_data(hdr);
 
@@ -2229,6 +2238,9 @@
 	switch (mtyp) {
 	case RESET_MSG:
 	case ACTIVATE_MSG:
+		msg_max = msg_max_pkt(hdr);
+		if (msg_max < tipc_bearer_min_mtu(l->net, l->bearer_id))
+			break;
 		/* Complete own link name with peer's interface name */
 		if_name =  strrchr(l->name, ':') + 1;
 		if (sizeof(l->name) - (if_name - l->name) <= TIPC_MAX_IF_NAME)
@@ -2273,11 +2285,16 @@
 		l->peer_session = msg_session(hdr);
 		l->in_session = true;
 		l->peer_bearer_id = msg_bearer_id(hdr);
-		if (l->mtu > msg_max_pkt(hdr))
-			l->mtu = msg_max_pkt(hdr);
+		if (l->mtu > msg_max)
+			l->mtu = msg_max;
 		break;
 
 	case STATE_MSG:
+		/* Validate Gap ACK blocks, drop if invalid */
+		glen = tipc_get_gap_ack_blks(&ga, l, hdr, true);
+		if (glen > dlen)
+			break;
+
 		l->rcv_nxt_state = msg_seqno(hdr) + 1;
 
 		/* Update own tolerance if peer indicates a non-zero value */
@@ -2305,7 +2322,8 @@
 
 		/* Receive Gap ACK blocks from peer if any */
 		glen = tipc_get_gap_ack_blks(&ga, l, hdr, true);
-
+		if(glen > dlen)
+			break;
 		tipc_mon_rcv(l->net, data + glen, dlen - glen, l->addr,
 			     &l->mon_state, l->bearer_id);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/monitor.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/monitor.c
@@ -160,7 +160,7 @@
 
 static int map_get(u64 up_map, int i)
 {
-	return (up_map & (1 << i)) >> i;
+	return (up_map & (1ULL << i)) >> i;
 }
 
 static struct tipc_peer *peer_prev(struct tipc_peer *peer)
@@ -496,6 +496,8 @@
 	state->probing = false;
 
 	/* Sanity check received domain record */
+	if (new_member_cnt > MAX_MON_DOMAIN)
+		return;
 	if (dlen < dom_rec_len(arrv_dom, 0))
 		return;
 	if (dlen != dom_rec_len(arrv_dom, new_member_cnt))
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/msg.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/msg.c
@@ -142,9 +142,9 @@
 	if (fragid == FIRST_FRAGMENT) {
 		if (unlikely(head))
 			goto err;
-		*buf = NULL;
 		if (skb_has_frag_list(frag) && __skb_linearize(frag))
 			goto err;
+		*buf = NULL;
 		frag = skb_unshare(frag, GFP_ATOMIC);
 		if (unlikely(!frag))
 			goto err;
@@ -156,6 +156,11 @@
 	if (!head)
 		goto err;
 
+	/* Either the input skb ownership is transferred to headskb
+	 * or the input skb is freed, clear the reference to avoid
+	 * bad access on error path.
+	 */
+	*buf = NULL;
 	if (skb_try_coalesce(head, frag, &headstolen, &delta)) {
 		kfree_skb_partial(frag, headstolen);
 	} else {
@@ -179,7 +184,6 @@
 		*headbuf = NULL;
 		return 1;
 	}
-	*buf = NULL;
 	return 0;
 err:
 	kfree_skb(*buf);
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/name_distr.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/name_distr.c
@@ -313,7 +313,7 @@
 		pr_warn_ratelimited("Failed to remove binding %u,%u from %u\n",
 				    ua.sr.type, ua.sr.lower, node);
 	} else {
-		pr_warn("Unrecognized name table message received\n");
+		pr_warn_ratelimited("Unknown name table message received\n");
 	}
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/name_table.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/name_table.c
@@ -967,7 +967,7 @@
 		list_for_each_entry(p, &sr->all_publ, all_publ)
 			if (p->key == *last_key)
 				break;
-		if (p->key != *last_key)
+		if (list_entry_is_head(p, &sr->all_publ, all_publ))
 			return -EPIPE;
 	} else {
 		p = list_first_entry(&sr->all_publ,
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/netlink.c
@@ -88,7 +88,7 @@
 
 const struct nla_policy tipc_nl_link_policy[TIPC_NLA_LINK_MAX + 1] = {
 	[TIPC_NLA_LINK_UNSPEC]		= { .type = NLA_UNSPEC },
-	[TIPC_NLA_LINK_NAME]		= { .type = NLA_STRING,
+	[TIPC_NLA_LINK_NAME]		= { .type = NLA_NUL_STRING,
 					    .len = TIPC_MAX_LINK_NAME },
 	[TIPC_NLA_LINK_MTU]		= { .type = NLA_U32 },
 	[TIPC_NLA_LINK_BROADCAST]	= { .type = NLA_FLAG },
@@ -125,7 +125,7 @@
 
 const struct nla_policy tipc_nl_bearer_policy[TIPC_NLA_BEARER_MAX + 1]	= {
 	[TIPC_NLA_BEARER_UNSPEC]	= { .type = NLA_UNSPEC },
-	[TIPC_NLA_BEARER_NAME]		= { .type = NLA_STRING,
+	[TIPC_NLA_BEARER_NAME]		= { .type = NLA_NUL_STRING,
 					    .len = TIPC_MAX_BEARER_NAME },
 	[TIPC_NLA_BEARER_PROP]		= { .type = NLA_NESTED },
 	[TIPC_NLA_BEARER_DOMAIN]	= { .type = NLA_U32 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/netlink_compat.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/netlink_compat.c
@@ -101,6 +101,7 @@
 		return -EMSGSIZE;
 
 	skb_put(skb, TLV_SPACE(len));
+	memset(tlv, 0, TLV_SPACE(len));
 	tlv->tlv_type = htons(type);
 	tlv->tlv_len = htons(TLV_LENGTH(len));
 	if (len && data)
@@ -880,7 +881,7 @@
 	};
 
 	ntq = (struct tipc_name_table_query *)TLV_DATA(msg->req);
-	if (TLV_GET_DATA_LEN(msg->req) < sizeof(struct tipc_name_table_query))
+	if (TLV_GET_DATA_LEN(msg->req) < (int)sizeof(struct tipc_name_table_query))
 		return -EINVAL;
 
 	depth = ntohl(ntq->depth);
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/node.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/node.c
@@ -403,7 +403,7 @@
 	u32 flags = n->action_flags;
 	struct list_head *publ_list;
 	struct tipc_uaddr ua;
-	u32 bearer_id;
+	u32 bearer_id, node;
 
 	if (likely(!flags)) {
 		write_unlock_bh(&n->lock);
@@ -413,7 +413,8 @@
 	tipc_uaddr(&ua, TIPC_SERVICE_RANGE, TIPC_NODE_SCOPE,
 		   TIPC_LINK_STATE, n->addr, n->addr);
 	sk.ref = n->link_id;
-	sk.node = n->addr;
+	sk.node = tipc_own_addr(net);
+	node = n->addr;
 	bearer_id = n->link_id & 0xffff;
 	publ_list = &n->publ_list;
 
@@ -423,17 +424,17 @@
 	write_unlock_bh(&n->lock);
 
 	if (flags & TIPC_NOTIFY_NODE_DOWN)
-		tipc_publ_notify(net, publ_list, sk.node, n->capabilities);
+		tipc_publ_notify(net, publ_list, node, n->capabilities);
 
 	if (flags & TIPC_NOTIFY_NODE_UP)
-		tipc_named_node_up(net, sk.node, n->capabilities);
+		tipc_named_node_up(net, node, n->capabilities);
 
 	if (flags & TIPC_NOTIFY_LINK_UP) {
-		tipc_mon_peer_up(net, sk.node, bearer_id);
+		tipc_mon_peer_up(net, node, bearer_id);
 		tipc_nametbl_publish(net, &ua, &sk, sk.ref);
 	}
 	if (flags & TIPC_NOTIFY_LINK_DOWN) {
-		tipc_mon_peer_down(net, sk.node, bearer_id);
+		tipc_mon_peer_down(net, node, bearer_id);
 		tipc_nametbl_withdraw(net, &ua, &sk, sk.ref);
 	}
 }
@@ -471,8 +472,8 @@
 				   bool preliminary)
 {
 	struct tipc_net *tn = net_generic(net, tipc_net_id);
+	struct tipc_link *l, *snd_l = tipc_bc_sndlink(net);
 	struct tipc_node *n, *temp_node;
-	struct tipc_link *l;
 	unsigned long intv;
 	int bearer_id;
 	int i;
@@ -487,6 +488,16 @@
 			goto exit;
 		/* A preliminary node becomes "real" now, refresh its data */
 		tipc_node_write_lock(n);
+		if (!tipc_link_bc_create(net, tipc_own_addr(net), addr, peer_id, U16_MAX,
+					 tipc_link_min_win(snd_l), tipc_link_max_win(snd_l),
+					 n->capabilities, &n->bc_entry.inputq1,
+					 &n->bc_entry.namedq, snd_l, &n->bc_entry.link)) {
+			pr_warn("Broadcast rcv link refresh failed, no memory\n");
+			tipc_node_write_unlock_fast(n);
+			tipc_node_put(n);
+			n = NULL;
+			goto exit;
+		}
 		n->preliminary = false;
 		n->addr = addr;
 		hlist_del_rcu(&n->hash);
@@ -566,7 +577,16 @@
 	n->signature = INVALID_NODE_SIG;
 	n->active_links[0] = INVALID_BEARER_ID;
 	n->active_links[1] = INVALID_BEARER_ID;
-	n->bc_entry.link = NULL;
+	if (!preliminary &&
+	    !tipc_link_bc_create(net, tipc_own_addr(net), addr, peer_id, U16_MAX,
+				 tipc_link_min_win(snd_l), tipc_link_max_win(snd_l),
+				 n->capabilities, &n->bc_entry.inputq1,
+				 &n->bc_entry.namedq, snd_l, &n->bc_entry.link)) {
+		pr_warn("Broadcast rcv link creation failed, no memory\n");
+		tipc_node_put(n);
+		n = NULL;
+		goto exit;
+	}
 	tipc_node_get(n);
 	timer_setup(&n->timer, tipc_node_timeout, 0);
 	/* Start a slow timer anyway, crypto needs it */
@@ -1154,13 +1174,14 @@
 			  bool *respond, bool *dupl_addr)
 {
 	struct tipc_node *n;
-	struct tipc_link *l, *snd_l;
+	struct tipc_link *l;
 	struct tipc_link_entry *le;
 	bool addr_match = false;
 	bool sign_match = false;
 	bool link_up = false;
+	bool link_is_reset = false;
 	bool accept_addr = false;
-	bool reset = true;
+	bool reset = false;
 	char *if_name;
 	unsigned long intv;
 	u16 session;
@@ -1174,36 +1195,20 @@
 		return;
 
 	tipc_node_write_lock(n);
-	if (unlikely(!n->bc_entry.link)) {
-		snd_l = tipc_bc_sndlink(net);
-		if (!tipc_link_bc_create(net, tipc_own_addr(net),
-					 addr, peer_id, U16_MAX,
-					 tipc_link_min_win(snd_l),
-					 tipc_link_max_win(snd_l),
-					 n->capabilities,
-					 &n->bc_entry.inputq1,
-					 &n->bc_entry.namedq, snd_l,
-					 &n->bc_entry.link)) {
-			pr_warn("Broadcast rcv link creation failed, no mem\n");
-			tipc_node_write_unlock_fast(n);
-			tipc_node_put(n);
-			return;
-		}
-	}
 
 	le = &n->links[b->identity];
 
 	/* Prepare to validate requesting node's signature and media address */
 	l = le->link;
 	link_up = l && tipc_link_is_up(l);
+	link_is_reset = l && tipc_link_is_reset(l);
 	addr_match = l && !memcmp(&le->maddr, maddr, sizeof(*maddr));
 	sign_match = (signature == n->signature);
 
 	/* These three flags give us eight permutations: */
 
 	if (sign_match && addr_match && link_up) {
-		/* All is fine. Do nothing. */
-		reset = false;
+		/* All is fine. Ignore requests. */
 		/* Peer node is not a container/local namespace */
 		if (!n->peer_hash_mix)
 			n->peer_hash_mix = hash_mixes;
@@ -1228,6 +1233,7 @@
 		 */
 		accept_addr = true;
 		*respond = true;
+		reset = true;
 	} else if (!sign_match && addr_match && link_up) {
 		/* Peer node rebooted. Two possibilities:
 		 *  - Delayed re-discovery; this link endpoint has already
@@ -1259,6 +1265,7 @@
 		n->signature = signature;
 		accept_addr = true;
 		*respond = true;
+		reset = true;
 	}
 
 	if (!accept_addr)
@@ -1287,6 +1294,7 @@
 		tipc_link_fsm_evt(l, LINK_RESET_EVT);
 		if (n->state == NODE_FAILINGOVER)
 			tipc_link_fsm_evt(l, LINK_FAILOVER_BEGIN_EVT);
+		link_is_reset = tipc_link_is_reset(l);
 		le->link = l;
 		n->link_cnt++;
 		tipc_node_calculate_timer(n, l);
@@ -1299,7 +1307,7 @@
 	memcpy(&le->maddr, maddr, sizeof(*maddr));
 exit:
 	tipc_node_write_unlock(n);
-	if (reset && l && !tipc_link_is_reset(l))
+	if (reset && !link_is_reset)
 		tipc_node_link_down(n, b->identity, false);
 	tipc_node_put(n);
 }
@@ -1685,6 +1693,7 @@
 	struct tipc_node *n;
 	struct sk_buff_head xmitq;
 	bool node_up = false;
+	struct net *peer_net;
 	int bearer_id;
 	int rc;
 
@@ -1701,18 +1710,23 @@
 		return -EHOSTUNREACH;
 	}
 
+	rcu_read_lock();
 	tipc_node_read_lock(n);
 	node_up = node_is_up(n);
-	if (node_up && n->peer_net && check_net(n->peer_net)) {
+	peer_net = n->peer_net;
+	tipc_node_read_unlock(n);
+	if (node_up && peer_net && check_net(peer_net)) {
 		/* xmit inner linux container */
-		tipc_lxc_xmit(n->peer_net, list);
+		tipc_lxc_xmit(peer_net, list);
 		if (likely(skb_queue_empty(list))) {
-			tipc_node_read_unlock(n);
+			rcu_read_unlock();
 			tipc_node_put(n);
 			return 0;
 		}
 	}
+	rcu_read_unlock();
 
+	tipc_node_read_lock(n);
 	bearer_id = n->active_links[selector & 1];
 	if (unlikely(bearer_id == INVALID_BEARER_ID)) {
 		tipc_node_read_unlock(n);
@@ -2093,6 +2107,7 @@
 	} else {
 		n = tipc_node_find_by_id(net, ehdr->id);
 	}
+	skb_dst_force(skb);
 	tipc_crypto_rcv(net, (n) ? n->crypto_rx : NULL, &skb, b);
 	if (!skb)
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/socket.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/socket.c
@@ -313,9 +313,9 @@
 		tipc_sk_respond(sk, skb, error);
 }
 
-static bool tipc_sk_connected(struct sock *sk)
+static bool tipc_sk_connected(const struct sock *sk)
 {
-	return sk->sk_state == TIPC_ESTABLISHED;
+	return READ_ONCE(sk->sk_state) == TIPC_ESTABLISHED;
 }
 
 /* tipc_sk_type_connectionless - check if the socket is datagram socket
@@ -502,6 +502,7 @@
 	sock_init_data(sock, sk);
 	tipc_set_sk_state(sk, TIPC_OPEN);
 	if (tipc_sk_insert(tsk)) {
+		sk_free(sk);
 		pr_warn("Socket create failed; port number exhausted\n");
 		return -EINVAL;
 	}
@@ -516,7 +517,7 @@
 	timer_setup(&sk->sk_timer, tipc_sk_timeout, 0);
 	sk->sk_shutdown = 0;
 	sk->sk_backlog_rcv = tipc_sk_backlog_rcv;
-	sk->sk_rcvbuf = sysctl_tipc_rmem[1];
+	sk->sk_rcvbuf = READ_ONCE(sysctl_tipc_rmem[1]);
 	sk->sk_data_ready = tipc_data_ready;
 	sk->sk_write_space = tipc_write_space;
 	sk->sk_destruct = tipc_sock_destruct;
@@ -1461,6 +1462,8 @@
 		msg_set_syn(hdr, 1);
 	}
 
+	memset(&skaddr, 0, sizeof(skaddr));
+
 	/* Determine destination */
 	if (atype == TIPC_SERVICE_RANGE) {
 		return tipc_sendmcast(sock, ua, m, dlen, timeout);
@@ -2850,7 +2853,8 @@
 
 	/* Try again later if dest link is congested */
 	if (tsk->cong_link_cnt) {
-		sk_reset_timer(sk, &sk->sk_timer, msecs_to_jiffies(100));
+		sk_reset_timer(sk, &sk->sk_timer,
+			       jiffies + msecs_to_jiffies(100));
 		return;
 	}
 	/* Prepare SYN for retransmit */
@@ -3747,7 +3751,7 @@
 			if (p->key == *last_publ)
 				break;
 		}
-		if (p->key != *last_publ) {
+		if (list_entry_is_head(p, &tsk->publications, binding_sock)) {
 			/* We never set seq or call nl_dump_check_consistent()
 			 * this means that setting prev_seq here will cause the
 			 * consistence check to fail in the netlink callback
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/topsrv.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/topsrv.c
@@ -176,7 +176,7 @@
 	conn_put(con);
 }
 
-static struct tipc_conn *tipc_conn_alloc(struct tipc_topsrv *s)
+static struct tipc_conn *tipc_conn_alloc(struct tipc_topsrv *s, struct socket *sock)
 {
 	struct tipc_conn *con;
 	int ret;
@@ -202,10 +202,12 @@
 	}
 	con->conid = ret;
 	s->idr_in_use++;
-	spin_unlock_bh(&s->idr_lock);
 
 	set_bit(CF_CONNECTED, &con->flags);
 	con->server = s;
+	con->sock = sock;
+	conn_get(con);
+	spin_unlock_bh(&s->idr_lock);
 
 	return con;
 }
@@ -450,17 +452,24 @@
 static void tipc_topsrv_accept(struct work_struct *work)
 {
 	struct tipc_topsrv *srv = container_of(work, struct tipc_topsrv, awork);
-	struct socket *lsock = srv->listener;
-	struct socket *newsock;
+	struct socket *newsock, *lsock;
 	struct tipc_conn *con;
 	struct sock *newsk;
 	int ret;
 
+	spin_lock_bh(&srv->idr_lock);
+	if (!srv->listener) {
+		spin_unlock_bh(&srv->idr_lock);
+		return;
+	}
+	lsock = srv->listener;
+	spin_unlock_bh(&srv->idr_lock);
+
 	while (1) {
 		ret = kernel_accept(lsock, &newsock, O_NONBLOCK);
 		if (ret < 0)
 			return;
-		con = tipc_conn_alloc(srv);
+		con = tipc_conn_alloc(srv, newsock);
 		if (IS_ERR(con)) {
 			ret = PTR_ERR(con);
 			sock_release(newsock);
@@ -472,11 +481,11 @@
 		newsk->sk_data_ready = tipc_conn_data_ready;
 		newsk->sk_write_space = tipc_conn_write_space;
 		newsk->sk_user_data = con;
-		con->sock = newsock;
 		write_unlock_bh(&newsk->sk_callback_lock);
 
 		/* Wake up receive process in case of 'SYN+' message */
 		newsk->sk_data_ready(newsk);
+		conn_put(con);
 	}
 }
 
@@ -489,7 +498,7 @@
 
 	read_lock_bh(&sk->sk_callback_lock);
 	srv = sk->sk_user_data;
-	if (srv->listener)
+	if (srv)
 		queue_work(srv->rcv_wq, &srv->awork);
 	read_unlock_bh(&sk->sk_callback_lock);
 }
@@ -568,19 +577,19 @@
 	sub.seq.upper = upper;
 	sub.timeout = TIPC_WAIT_FOREVER;
 	sub.filter = filter;
-	*(u32 *)&sub.usr_handle = port;
+	*(u64 *)&sub.usr_handle = (u64)port;
 
-	con = tipc_conn_alloc(tipc_topsrv(net));
+	con = tipc_conn_alloc(tipc_topsrv(net), NULL);
 	if (IS_ERR(con))
 		return false;
 
 	*conid = con->conid;
-	con->sock = NULL;
 	rc = tipc_conn_rcv_sub(tipc_topsrv(net), con, &sub);
-	if (rc >= 0)
-		return true;
+	if (rc)
+		conn_put(con);
+
 	conn_put(con);
-	return false;
+	return !rc;
 }
 
 void tipc_topsrv_kern_unsubscr(struct net *net, int conid)
@@ -699,8 +708,9 @@
 	__module_get(lsock->sk->sk_prot_creator->owner);
 	srv->listener = NULL;
 	spin_unlock_bh(&srv->idr_lock);
-	sock_release(lsock);
+
 	tipc_topsrv_work_stop(srv);
+	sock_release(lsock);
 	idr_destroy(&srv->conn_idr);
 	kfree(srv);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/tipc/udp_media.c
+++ linux-xilinx-zynqmp-5.15.0/net/tipc/udp_media.c
@@ -135,8 +135,11 @@
 		snprintf(buf, size, "%pI4:%u", &ua->ipv4, ntohs(ua->port));
 	else if (ntohs(ua->proto) == ETH_P_IPV6)
 		snprintf(buf, size, "%pI6:%u", &ua->ipv6, ntohs(ua->port));
-	else
+	else {
 		pr_err("Invalid UDP media address\n");
+		return 1;
+	}
+
 	return 0;
 }
 
@@ -738,8 +741,8 @@
 			udp_conf.local_ip.s_addr = local.ipv4.s_addr;
 		udp_conf.use_udp_checksums = false;
 		ub->ifindex = dev->ifindex;
-		if (tipc_mtu_bad(dev, sizeof(struct iphdr) +
-				      sizeof(struct udphdr))) {
+		b->encap_hlen = sizeof(struct iphdr) + sizeof(struct udphdr);
+		if (tipc_mtu_bad(dev, b->encap_hlen)) {
 			err = -EINVAL;
 			goto err;
 		}
@@ -760,6 +763,7 @@
 		else
 			udp_conf.local_ip6 = local.ipv6;
 		ub->ifindex = dev->ifindex;
+		b->encap_hlen = sizeof(struct ipv6hdr) + sizeof(struct udphdr);
 		b->mtu = 1280;
 #endif
 	} else {
@@ -807,6 +811,7 @@
 {
 	struct udp_bearer *ub = container_of(work, struct udp_bearer, work);
 	struct udp_replicast *rcast, *tmp;
+	struct tipc_net *tn;
 
 	list_for_each_entry_safe(rcast, tmp, &ub->rcast.list, list) {
 		dst_cache_destroy(&rcast->dst_cache);
@@ -814,10 +819,14 @@
 		kfree_rcu(rcast, rcu);
 	}
 
-	atomic_dec(&tipc_net(sock_net(ub->ubsock->sk))->wq_count);
+	tn = tipc_net(sock_net(ub->ubsock->sk));
+
 	dst_cache_destroy(&ub->rcast.dst_cache);
 	udp_tunnel_sock_release(ub->ubsock);
+
+	/* Note: could use a call_rcu() to avoid another synchronize_net() */
 	synchronize_net();
+	atomic_dec(&tn->wq_count);
 	kfree(ub);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/tls/tls_device.c
+++ linux-xilinx-zynqmp-5.15.0/net/tls/tls_device.c
@@ -45,14 +45,14 @@
  */
 static DECLARE_RWSEM(device_offload_lock);
 
-static void tls_device_gc_task(struct work_struct *work);
+static struct workqueue_struct *destruct_wq __read_mostly;
 
-static DECLARE_WORK(tls_device_gc_work, tls_device_gc_task);
-static LIST_HEAD(tls_device_gc_list);
 static LIST_HEAD(tls_device_list);
 static LIST_HEAD(tls_device_down_list);
 static DEFINE_SPINLOCK(tls_device_lock);
 
+static struct page *dummy_page;
+
 static void tls_device_free_ctx(struct tls_context *ctx)
 {
 	if (ctx->tx_conf == TLS_HW) {
@@ -67,44 +67,44 @@
 	tls_ctx_free(NULL, ctx);
 }
 
-static void tls_device_gc_task(struct work_struct *work)
+static void tls_device_tx_del_task(struct work_struct *work)
 {
-	struct tls_context *ctx, *tmp;
-	unsigned long flags;
-	LIST_HEAD(gc_list);
-
-	spin_lock_irqsave(&tls_device_lock, flags);
-	list_splice_init(&tls_device_gc_list, &gc_list);
-	spin_unlock_irqrestore(&tls_device_lock, flags);
-
-	list_for_each_entry_safe(ctx, tmp, &gc_list, list) {
-		struct net_device *netdev = ctx->netdev;
-
-		if (netdev && ctx->tx_conf == TLS_HW) {
-			netdev->tlsdev_ops->tls_dev_del(netdev, ctx,
-							TLS_OFFLOAD_CTX_DIR_TX);
-			dev_put(netdev);
-			ctx->netdev = NULL;
-		}
+	struct tls_offload_context_tx *offload_ctx =
+		container_of(work, struct tls_offload_context_tx, destruct_work);
+	struct tls_context *ctx = offload_ctx->ctx;
+	struct net_device *netdev = ctx->netdev;
 
-		list_del(&ctx->list);
-		tls_device_free_ctx(ctx);
-	}
+	netdev->tlsdev_ops->tls_dev_del(netdev, ctx, TLS_OFFLOAD_CTX_DIR_TX);
+	dev_put(netdev);
+	ctx->netdev = NULL;
+	tls_device_free_ctx(ctx);
 }
 
 static void tls_device_queue_ctx_destruction(struct tls_context *ctx)
 {
 	unsigned long flags;
+	bool async_cleanup;
 
 	spin_lock_irqsave(&tls_device_lock, flags);
-	list_move_tail(&ctx->list, &tls_device_gc_list);
+	if (unlikely(!refcount_dec_and_test(&ctx->refcount))) {
+		spin_unlock_irqrestore(&tls_device_lock, flags);
+		return;
+	}
 
-	/* schedule_work inside the spinlock
-	 * to make sure tls_device_down waits for that work.
-	 */
-	schedule_work(&tls_device_gc_work);
+	list_del(&ctx->list); /* Remove from tls_device_list / tls_device_down_list */
+	async_cleanup = ctx->netdev && ctx->tx_conf == TLS_HW;
+	if (async_cleanup) {
+		struct tls_offload_context_tx *offload_ctx = tls_offload_ctx_tx(ctx);
 
+		/* queue_work inside the spinlock
+		 * to make sure tls_device_down waits for that work.
+		 */
+		queue_work(destruct_wq, &offload_ctx->destruct_work);
+	}
 	spin_unlock_irqrestore(&tls_device_lock, flags);
+
+	if (!async_cleanup)
+		tls_device_free_ctx(ctx);
 }
 
 /* We assume that the socket is already connected */
@@ -194,8 +194,7 @@
 		clean_acked_data_disable(inet_csk(sk));
 	}
 
-	if (refcount_dec_and_test(&tls_ctx->refcount))
-		tls_device_queue_ctx_destruction(tls_ctx);
+	tls_device_queue_ctx_destruction(tls_ctx);
 }
 EXPORT_SYMBOL_GPL(tls_device_sk_destruct);
 
@@ -300,36 +299,33 @@
 	return tls_push_sg(sk, ctx, offload_ctx->sg_tx_data, 0, flags);
 }
 
-static int tls_device_record_close(struct sock *sk,
-				   struct tls_context *ctx,
-				   struct tls_record_info *record,
-				   struct page_frag *pfrag,
-				   unsigned char record_type)
+static void tls_device_record_close(struct sock *sk,
+				    struct tls_context *ctx,
+				    struct tls_record_info *record,
+				    struct page_frag *pfrag,
+				    unsigned char record_type)
 {
 	struct tls_prot_info *prot = &ctx->prot_info;
-	int ret;
+	struct page_frag dummy_tag_frag;
 
 	/* append tag
 	 * device will fill in the tag, we just need to append a placeholder
 	 * use socket memory to improve coalescing (re-using a single buffer
 	 * increases frag count)
-	 * if we can't allocate memory now, steal some back from data
+	 * if we can't allocate memory now use the dummy page
 	 */
-	if (likely(skb_page_frag_refill(prot->tag_size, pfrag,
-					sk->sk_allocation))) {
-		ret = 0;
-		tls_append_frag(record, pfrag, prot->tag_size);
-	} else {
-		ret = prot->tag_size;
-		if (record->len <= prot->overhead_size)
-			return -ENOMEM;
+	if (unlikely(pfrag->size - pfrag->offset < prot->tag_size) &&
+	    !skb_page_frag_refill(prot->tag_size, pfrag, sk->sk_allocation)) {
+		dummy_tag_frag.page = dummy_page;
+		dummy_tag_frag.offset = 0;
+		pfrag = &dummy_tag_frag;
 	}
+	tls_append_frag(record, pfrag, prot->tag_size);
 
 	/* fill prepend */
 	tls_fill_prepend(ctx, skb_frag_address(&record->frags[0]),
 			 record->len - prot->overhead_size,
 			 record_type);
-	return ret;
 }
 
 static int tls_create_new_record(struct tls_offload_context_tx *offload_ctx,
@@ -483,11 +479,13 @@
 		copy = min_t(size_t, size, (pfrag->size - pfrag->offset));
 		copy = min_t(size_t, copy, (max_open_record_len - record->len));
 
-		rc = tls_device_copy_data(page_address(pfrag->page) +
-					  pfrag->offset, copy, msg_iter);
-		if (rc)
-			goto handle_error;
-		tls_append_frag(record, pfrag, copy);
+		if (copy) {
+			rc = tls_device_copy_data(page_address(pfrag->page) +
+						  pfrag->offset, copy, msg_iter);
+			if (rc)
+				goto handle_error;
+			tls_append_frag(record, pfrag, copy);
+		}
 
 		size -= copy;
 		if (!size) {
@@ -503,18 +501,8 @@
 
 		if (done || record->len >= max_open_record_len ||
 		    (record->num_frags >= MAX_SKB_FRAGS - 1)) {
-			rc = tls_device_record_close(sk, tls_ctx, record,
-						     pfrag, record_type);
-			if (rc) {
-				if (rc > 0) {
-					size += rc;
-				} else {
-					size = orig_size;
-					destroy_record(record);
-					ctx->open_record = NULL;
-					break;
-				}
-			}
+			tls_device_record_close(sk, tls_ctx, record,
+						pfrag, record_type);
 
 			rc = tls_push_record(sk,
 					     tls_ctx,
@@ -962,11 +950,9 @@
 				   tls_ctx->rx.rec_seq, rxm->full_len,
 				   is_encrypted, is_decrypted);
 
-	ctx->sw.decrypted |= is_decrypted;
-
 	if (unlikely(test_bit(TLS_RX_DEV_DEGRADED, &tls_ctx->flags))) {
 		if (likely(is_encrypted || is_decrypted))
-			return 0;
+			return is_decrypted;
 
 		/* After tls_device_down disables the offload, the next SKB will
 		 * likely have initial fragments decrypted, and final ones not
@@ -981,7 +967,7 @@
 	 */
 	if (is_decrypted) {
 		ctx->resync_nh_reset = 1;
-		return 0;
+		return is_decrypted;
 	}
 	if (is_encrypted) {
 		tls_device_core_ctrl_rx_resync(tls_ctx, ctx, sk, skb);
@@ -1101,6 +1087,9 @@
 	start_marker_record->len = 0;
 	start_marker_record->num_frags = 0;
 
+	INIT_WORK(&offload_ctx->destruct_work, tls_device_tx_del_task);
+	offload_ctx->ctx = ctx;
+
 	INIT_LIST_HEAD(&offload_ctx->records_list);
 	list_add_tail(&start_marker_record->list, &offload_ctx->records_list);
 	spin_lock_init(&offload_ctx->lock);
@@ -1345,12 +1334,20 @@
 
 		/* Device contexts for RX and TX will be freed in on sk_destruct
 		 * by tls_device_free_ctx. rx_conf and tx_conf stay in TLS_HW.
+		 * Now release the ref taken above.
 		 */
+		if (refcount_dec_and_test(&ctx->refcount)) {
+			/* sk_destruct ran after tls_device_down took a ref, and
+			 * it returned early. Complete the destruction here.
+			 */
+			list_del(&ctx->list);
+			tls_device_free_ctx(ctx);
+		}
 	}
 
 	up_write(&device_offload_lock);
 
-	flush_work(&tls_device_gc_work);
+	flush_workqueue(destruct_wq);
 
 	return NOTIFY_DONE;
 }
@@ -1389,14 +1386,38 @@
 	.notifier_call	= tls_dev_event,
 };
 
-void __init tls_device_init(void)
+int __init tls_device_init(void)
 {
-	register_netdevice_notifier(&tls_dev_notifier);
+	int err;
+
+	dummy_page = alloc_page(GFP_KERNEL);
+	if (!dummy_page)
+		return -ENOMEM;
+
+	destruct_wq = alloc_workqueue("ktls_device_destruct", 0, 0);
+	if (!destruct_wq) {
+		err = -ENOMEM;
+		goto err_free_dummy;
+	}
+
+	err = register_netdevice_notifier(&tls_dev_notifier);
+	if (err)
+		goto err_destroy_wq;
+
+	return 0;
+
+err_destroy_wq:
+	destroy_workqueue(destruct_wq);
+err_free_dummy:
+	put_page(dummy_page);
+	return err;
 }
 
 void __exit tls_device_cleanup(void)
 {
 	unregister_netdevice_notifier(&tls_dev_notifier);
-	flush_work(&tls_device_gc_work);
+	flush_workqueue(destruct_wq);
+	destroy_workqueue(destruct_wq);
 	clean_acked_data_flush();
+	put_page(dummy_page);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/tls/tls_main.c
+++ linux-xilinx-zynqmp-5.15.0/net/tls/tls_main.c
@@ -61,7 +61,7 @@
 static const struct proto *saved_tcpv4_prot;
 static DEFINE_MUTEX(tcpv4_prot_mutex);
 static struct proto tls_prots[TLS_NUM_PROTS][TLS_NUM_CONFIG][TLS_NUM_CONFIG];
-static struct proto_ops tls_sw_proto_ops;
+static struct proto_ops tls_proto_ops[TLS_NUM_PROTS][TLS_NUM_CONFIG][TLS_NUM_CONFIG];
 static void build_protos(struct proto prot[TLS_NUM_CONFIG][TLS_NUM_CONFIG],
 			 const struct proto *base);
 
@@ -71,6 +71,8 @@
 
 	WRITE_ONCE(sk->sk_prot,
 		   &tls_prots[ip_ver][ctx->tx_conf][ctx->rx_conf]);
+	WRITE_ONCE(sk->sk_socket->ops,
+		   &tls_proto_ops[ip_ver][ctx->tx_conf][ctx->rx_conf]);
 }
 
 int wait_on_pending_writer(struct sock *sk, long *timeo)
@@ -90,7 +92,8 @@
 			break;
 		}
 
-		if (sk_wait_event(sk, timeo, !sk->sk_write_pending, &wait))
+		if (sk_wait_event(sk, timeo,
+				  !READ_ONCE(sk->sk_write_pending), &wait))
 			break;
 	}
 	remove_wait_queue(sk_sleep(sk), &wait);
@@ -384,13 +387,11 @@
 			rc = -EINVAL;
 			goto out;
 		}
-		lock_sock(sk);
 		memcpy(crypto_info_aes_gcm_128->iv,
 		       cctx->iv + TLS_CIPHER_AES_GCM_128_SALT_SIZE,
 		       TLS_CIPHER_AES_GCM_128_IV_SIZE);
 		memcpy(crypto_info_aes_gcm_128->rec_seq, cctx->rec_seq,
 		       TLS_CIPHER_AES_GCM_128_REC_SEQ_SIZE);
-		release_sock(sk);
 		if (copy_to_user(optval,
 				 crypto_info_aes_gcm_128,
 				 sizeof(*crypto_info_aes_gcm_128)))
@@ -408,13 +409,11 @@
 			rc = -EINVAL;
 			goto out;
 		}
-		lock_sock(sk);
 		memcpy(crypto_info_aes_gcm_256->iv,
 		       cctx->iv + TLS_CIPHER_AES_GCM_256_SALT_SIZE,
 		       TLS_CIPHER_AES_GCM_256_IV_SIZE);
 		memcpy(crypto_info_aes_gcm_256->rec_seq, cctx->rec_seq,
 		       TLS_CIPHER_AES_GCM_256_REC_SEQ_SIZE);
-		release_sock(sk);
 		if (copy_to_user(optval,
 				 crypto_info_aes_gcm_256,
 				 sizeof(*crypto_info_aes_gcm_256)))
@@ -434,6 +433,8 @@
 {
 	int rc = 0;
 
+	lock_sock(sk);
+
 	switch (optname) {
 	case TLS_TX:
 	case TLS_RX:
@@ -444,6 +445,9 @@
 		rc = -ENOPROTOOPT;
 		break;
 	}
+
+	release_sock(sk);
+
 	return rc;
 }
 
@@ -581,8 +585,6 @@
 	if (tx) {
 		ctx->sk_write_space = sk->sk_write_space;
 		sk->sk_write_space = tls_write_space;
-	} else {
-		sk->sk_socket->ops = &tls_sw_proto_ops;
 	}
 	goto out;
 
@@ -634,12 +636,53 @@
 		return NULL;
 
 	mutex_init(&ctx->tx_lock);
-	rcu_assign_pointer(icsk->icsk_ulp_data, ctx);
 	ctx->sk_proto = READ_ONCE(sk->sk_prot);
 	ctx->sk = sk;
+	/* Release semantic of rcu_assign_pointer() ensures that
+	 * ctx->sk_proto is visible before changing sk->sk_prot in
+	 * update_sk_prot(), and prevents reading uninitialized value in
+	 * tls_{getsockopt, setsockopt}. Note that we do not need a
+	 * read barrier in tls_{getsockopt,setsockopt} as there is an
+	 * address dependency between sk->sk_proto->{getsockopt,setsockopt}
+	 * and ctx->sk_proto.
+	 */
+	rcu_assign_pointer(icsk->icsk_ulp_data, ctx);
 	return ctx;
 }
 
+static void build_proto_ops(struct proto_ops ops[TLS_NUM_CONFIG][TLS_NUM_CONFIG],
+			    const struct proto_ops *base)
+{
+	ops[TLS_BASE][TLS_BASE] = *base;
+
+	ops[TLS_SW  ][TLS_BASE] = ops[TLS_BASE][TLS_BASE];
+	ops[TLS_SW  ][TLS_BASE].sendpage_locked	= tls_sw_sendpage_locked;
+
+	ops[TLS_BASE][TLS_SW  ] = ops[TLS_BASE][TLS_BASE];
+	ops[TLS_BASE][TLS_SW  ].splice_read	= tls_sw_splice_read;
+
+	ops[TLS_SW  ][TLS_SW  ] = ops[TLS_SW  ][TLS_BASE];
+	ops[TLS_SW  ][TLS_SW  ].splice_read	= tls_sw_splice_read;
+
+#ifdef CONFIG_TLS_DEVICE
+	ops[TLS_HW  ][TLS_BASE] = ops[TLS_BASE][TLS_BASE];
+	ops[TLS_HW  ][TLS_BASE].sendpage_locked	= NULL;
+
+	ops[TLS_HW  ][TLS_SW  ] = ops[TLS_BASE][TLS_SW  ];
+	ops[TLS_HW  ][TLS_SW  ].sendpage_locked	= NULL;
+
+	ops[TLS_BASE][TLS_HW  ] = ops[TLS_BASE][TLS_SW  ];
+
+	ops[TLS_SW  ][TLS_HW  ] = ops[TLS_SW  ][TLS_SW  ];
+
+	ops[TLS_HW  ][TLS_HW  ] = ops[TLS_HW  ][TLS_SW  ];
+	ops[TLS_HW  ][TLS_HW  ].sendpage_locked	= NULL;
+#endif
+#ifdef CONFIG_TLS_TOE
+	ops[TLS_HW_RECORD][TLS_HW_RECORD] = *base;
+#endif
+}
+
 static void tls_build_proto(struct sock *sk)
 {
 	int ip_ver = sk->sk_family == AF_INET6 ? TLSV6 : TLSV4;
@@ -651,6 +694,8 @@
 		mutex_lock(&tcpv6_prot_mutex);
 		if (likely(prot != saved_tcpv6_prot)) {
 			build_protos(tls_prots[TLSV6], prot);
+			build_proto_ops(tls_proto_ops[TLSV6],
+					sk->sk_socket->ops);
 			smp_store_release(&saved_tcpv6_prot, prot);
 		}
 		mutex_unlock(&tcpv6_prot_mutex);
@@ -661,6 +706,8 @@
 		mutex_lock(&tcpv4_prot_mutex);
 		if (likely(prot != saved_tcpv4_prot)) {
 			build_protos(tls_prots[TLSV4], prot);
+			build_proto_ops(tls_proto_ops[TLSV4],
+					sk->sk_socket->ops);
 			smp_store_release(&saved_tcpv4_prot, prot);
 		}
 		mutex_unlock(&tcpv4_prot_mutex);
@@ -753,6 +800,8 @@
 {
 	struct tls_context *ctx;
 
+	WARN_ON_ONCE(sk->sk_prot == p);
+
 	ctx = tls_get_ctx(sk);
 	if (likely(ctx)) {
 		ctx->sk_write_space = write_space;
@@ -764,7 +813,7 @@
 	}
 }
 
-static int tls_get_info(const struct sock *sk, struct sk_buff *skb)
+static int tls_get_info(struct sock *sk, struct sk_buff *skb)
 {
 	u16 version, cipher_type;
 	struct tls_context *ctx;
@@ -871,11 +920,12 @@
 	if (err)
 		return err;
 
-	tls_sw_proto_ops = inet_stream_ops;
-	tls_sw_proto_ops.splice_read = tls_sw_splice_read;
-	tls_sw_proto_ops.sendpage_locked   = tls_sw_sendpage_locked;
+	err = tls_device_init();
+	if (err) {
+		unregister_pernet_subsys(&tls_proc_ops);
+		return err;
+	}
 
-	tls_device_init();
 	tcp_register_ulp(&tcp_tls_ulp_ops);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/tls/tls_sw.c
+++ linux-xilinx-zynqmp-5.15.0/net/tls/tls_sw.c
@@ -44,6 +44,12 @@
 #include <net/strparser.h>
 #include <net/tls.h>
 
+struct tls_decrypt_arg {
+	bool zc;
+	bool async;
+	bool async_done;
+};
+
 noinline void tls_err_abort(struct sock *sk, int err)
 {
 	WARN_ON_ONCE(err >= 0);
@@ -128,10 +134,10 @@
         return __skb_nsg(skb, offset, len, 0);
 }
 
-static int padding_length(struct tls_sw_context_rx *ctx,
-			  struct tls_prot_info *prot, struct sk_buff *skb)
+static int padding_length(struct tls_prot_info *prot, struct sk_buff *skb)
 {
 	struct strp_msg *rxm = strp_msg(skb);
+	struct tls_msg *tlm = tls_msg(skb);
 	int sub = 0;
 
 	/* Determine zero-padding length */
@@ -153,7 +159,7 @@
 			sub++;
 			back++;
 		}
-		ctx->control = content_type;
+		tlm->control = content_type;
 	}
 	return sub;
 }
@@ -169,7 +175,17 @@
 	struct scatterlist *sg;
 	struct sk_buff *skb;
 	unsigned int pages;
-	int pending;
+
+	/* If requests get too backlogged crypto API returns -EBUSY and calls
+	 * ->complete(-EINPROGRESS) immediately followed by ->complete(0)
+	 * to make waiting for backlog to flush with crypto_wait_req() easier.
+	 * First wait converts -EBUSY -> -EINPROGRESS, and the second one
+	 * -EINPROGRESS -> 0.
+	 * We have a single struct crypto_async_request per direction, this
+	 * scheme doesn't help us, so just ignore the first ->complete().
+	 */
+	if (err == -EINPROGRESS)
+		return;
 
 	skb = (struct sk_buff *)req->data;
 	tls_ctx = tls_get_ctx(skb->sk);
@@ -187,7 +203,7 @@
 		struct strp_msg *rxm = strp_msg(skb);
 		int pad;
 
-		pad = padding_length(ctx, prot, skb);
+		pad = padding_length(prot, skb);
 		if (pad < 0) {
 			ctx->async_wait.err = pad;
 			tls_err_abort(skb->sk, pad);
@@ -216,12 +232,17 @@
 
 	kfree(aead_req);
 
-	spin_lock_bh(&ctx->decrypt_compl_lock);
-	pending = atomic_dec_return(&ctx->decrypt_pending);
-
-	if (!pending && ctx->async_notify)
+	if (atomic_dec_and_test(&ctx->decrypt_pending))
 		complete(&ctx->async_wait.completion);
-	spin_unlock_bh(&ctx->decrypt_compl_lock);
+}
+
+static int tls_decrypt_async_wait(struct tls_sw_context_rx *ctx)
+{
+	if (!atomic_dec_and_test(&ctx->decrypt_pending))
+		crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
+	atomic_inc(&ctx->decrypt_pending);
+
+	return ctx->async_wait.err;
 }
 
 static int tls_do_decryption(struct sock *sk,
@@ -231,7 +252,7 @@
 			     char *iv_recv,
 			     size_t data_len,
 			     struct aead_request *aead_req,
-			     bool async)
+			     struct tls_decrypt_arg *darg)
 {
 	struct tls_context *tls_ctx = tls_get_ctx(sk);
 	struct tls_prot_info *prot = &tls_ctx->prot_info;
@@ -244,7 +265,7 @@
 			       data_len + prot->tag_size,
 			       (u8 *)iv_recv);
 
-	if (async) {
+	if (darg->async) {
 		/* Using skb->sk to push sk through to crypto async callback
 		 * handler. This allows propagating errors up to the socket
 		 * if needed. It _must_ be cleared in the async handler
@@ -257,21 +278,31 @@
 					  tls_decrypt_done, skb);
 		atomic_inc(&ctx->decrypt_pending);
 	} else {
+		DECLARE_CRYPTO_WAIT(wait);
+
 		aead_request_set_callback(aead_req,
 					  CRYPTO_TFM_REQ_MAY_BACKLOG,
-					  crypto_req_done, &ctx->async_wait);
+					  crypto_req_done, &wait);
+		ret = crypto_aead_decrypt(aead_req);
+		if (ret == -EINPROGRESS || ret == -EBUSY)
+			ret = crypto_wait_req(ret, &wait);
+		return ret;
 	}
 
 	ret = crypto_aead_decrypt(aead_req);
-	if (ret == -EINPROGRESS) {
-		if (async)
-			return ret;
+	if (ret == -EINPROGRESS)
+		return 0;
 
-		ret = crypto_wait_req(ret, &ctx->async_wait);
+	if (ret == -EBUSY) {
+		ret = tls_decrypt_async_wait(ctx);
+		darg->async_done = true;
+		/* all completions have run, we're not doing async anymore */
+		darg->async = false;
+		return ret;
 	}
 
-	if (async)
-		atomic_dec(&ctx->decrypt_pending);
+	atomic_dec(&ctx->decrypt_pending);
+	darg->async = false;
 
 	return ret;
 }
@@ -428,7 +459,7 @@
 
 tx_err:
 	if (rc < 0 && rc != -EAGAIN)
-		tls_err_abort(sk, -EBADMSG);
+		tls_err_abort(sk, rc);
 
 	return rc;
 }
@@ -443,8 +474,9 @@
 	struct scatterlist *sge;
 	struct sk_msg *msg_en;
 	struct tls_rec *rec;
-	bool ready = false;
-	int pending;
+
+	if (err == -EINPROGRESS) /* see the comment in tls_decrypt_done() */
+		return;
 
 	rec = container_of(aead_req, struct tls_rec, aead_req);
 	msg_en = &rec->msg_encrypted;
@@ -475,23 +507,25 @@
 		/* If received record is at head of tx_list, schedule tx */
 		first_rec = list_first_entry(&ctx->tx_list,
 					     struct tls_rec, list);
-		if (rec == first_rec)
-			ready = true;
+		if (rec == first_rec) {
+			/* Schedule the transmission */
+			if (!test_and_set_bit(BIT_TX_SCHEDULED,
+					      &ctx->tx_bitmask))
+				schedule_delayed_work(&ctx->tx_work.work, 1);
+		}
 	}
 
-	spin_lock_bh(&ctx->encrypt_compl_lock);
-	pending = atomic_dec_return(&ctx->encrypt_pending);
-
-	if (!pending && ctx->async_notify)
+	if (atomic_dec_and_test(&ctx->encrypt_pending))
 		complete(&ctx->async_wait.completion);
-	spin_unlock_bh(&ctx->encrypt_compl_lock);
+}
 
-	if (!ready)
-		return;
+static int tls_encrypt_async_wait(struct tls_sw_context_tx *ctx)
+{
+	if (!atomic_dec_and_test(&ctx->encrypt_pending))
+		crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
+	atomic_inc(&ctx->encrypt_pending);
 
-	/* Schedule the transmission */
-	if (!test_and_set_bit(BIT_TX_SCHEDULED, &ctx->tx_bitmask))
-		schedule_delayed_work(&ctx->tx_work.work, 1);
+	return ctx->async_wait.err;
 }
 
 static int tls_do_encryption(struct sock *sk,
@@ -515,7 +549,7 @@
 	memcpy(&rec->iv_data[iv_offset], tls_ctx->tx.iv,
 	       prot->iv_size + prot->salt_size);
 
-	xor_iv_with_seq(prot, rec->iv_data, tls_ctx->tx.rec_seq);
+	xor_iv_with_seq(prot, rec->iv_data + iv_offset, tls_ctx->tx.rec_seq);
 
 	sge->offset += prot->prepend_size;
 	sge->length -= prot->prepend_size;
@@ -536,6 +570,10 @@
 	atomic_inc(&ctx->encrypt_pending);
 
 	rc = crypto_aead_encrypt(aead_req);
+	if (rc == -EBUSY) {
+		rc = tls_encrypt_async_wait(ctx);
+		rc = rc ?: -EINPROGRESS;
+	}
 	if (!rc || rc != -EINPROGRESS) {
 		atomic_dec(&ctx->encrypt_pending);
 		sge->offset -= prot->prepend_size;
@@ -801,7 +839,7 @@
 	struct sk_psock *psock;
 	struct sock *sk_redir;
 	struct tls_rec *rec;
-	bool enospc, policy;
+	bool enospc, policy, redir_ingress;
 	int err = 0, send;
 	u32 delta = 0;
 
@@ -809,7 +847,7 @@
 	psock = sk_psock_get(sk);
 	if (!psock || !policy) {
 		err = tls_push_record(sk, flags, record_type);
-		if (err && sk->sk_err == EBADMSG) {
+		if (err && err != -EINPROGRESS && sk->sk_err == EBADMSG) {
 			*copied -= sk_msg_free(sk, msg);
 			tls_free_open_rec(sk);
 			err = -sk->sk_err;
@@ -838,7 +876,7 @@
 	switch (psock->eval) {
 	case __SK_PASS:
 		err = tls_push_record(sk, flags, record_type);
-		if (err && sk->sk_err == EBADMSG) {
+		if (err && err != -EINPROGRESS && sk->sk_err == EBADMSG) {
 			*copied -= sk_msg_free(sk, msg);
 			tls_free_open_rec(sk);
 			err = -sk->sk_err;
@@ -846,6 +884,7 @@
 		}
 		break;
 	case __SK_REDIRECT:
+		redir_ingress = psock->redir_ingress;
 		sk_redir = psock->sk_redir;
 		memcpy(&msg_redir, msg, sizeof(*msg));
 		if (msg->apply_bytes < send)
@@ -855,7 +894,8 @@
 		sk_msg_return_zero(sk, msg, send);
 		msg->sg.size -= send;
 		release_sock(sk);
-		err = tcp_bpf_sendmsg_redir(sk_redir, &msg_redir, send, flags);
+		err = tcp_bpf_sendmsg_redir(sk_redir, redir_ingress,
+					    &msg_redir, send, flags);
 		lock_sock(sk);
 		if (err < 0) {
 			*copied -= sk_msg_free_nocharge(sk, &msg_redir);
@@ -942,13 +982,14 @@
 	int num_zc = 0;
 	int orig_size;
 	int ret = 0;
-	int pending;
 
 	if (msg->msg_flags & ~(MSG_MORE | MSG_DONTWAIT | MSG_NOSIGNAL |
 			       MSG_CMSG_COMPAT))
 		return -EOPNOTSUPP;
 
-	mutex_lock(&tls_ctx->tx_lock);
+	ret = mutex_lock_interruptible(&tls_ctx->tx_lock);
+	if (ret)
+		return ret;
 	lock_sock(sk);
 
 	if (unlikely(msg->msg_controllen)) {
@@ -1109,24 +1150,12 @@
 	if (!num_async) {
 		goto send_end;
 	} else if (num_zc) {
-		/* Wait for pending encryptions to get completed */
-		spin_lock_bh(&ctx->encrypt_compl_lock);
-		ctx->async_notify = true;
-
-		pending = atomic_read(&ctx->encrypt_pending);
-		spin_unlock_bh(&ctx->encrypt_compl_lock);
-		if (pending)
-			crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
-		else
-			reinit_completion(&ctx->async_wait.completion);
-
-		/* There can be no concurrent accesses, since we have no
-		 * pending encrypt operations
-		 */
-		WRITE_ONCE(ctx->async_notify, false);
+		int err;
 
-		if (ctx->async_wait.err) {
-			ret = ctx->async_wait.err;
+		/* Wait for pending encryptions to get completed */
+		err = tls_encrypt_async_wait(ctx);
+		if (err) {
+			ret = err;
 			copied = 0;
 		}
 	}
@@ -1212,6 +1241,8 @@
 		}
 
 		sk_msg_page_add(msg_pl, page, copy, offset);
+		msg_pl->sg.copybreak = 0;
+		msg_pl->sg.curr = msg_pl->sg.end;
 		sk_mem_charge(sk, copy);
 
 		offset += copy;
@@ -1282,7 +1313,9 @@
 		      MSG_SENDPAGE_NOTLAST | MSG_SENDPAGE_NOPOLICY))
 		return -EOPNOTSUPP;
 
-	mutex_lock(&tls_ctx->tx_lock);
+	ret = mutex_lock_interruptible(&tls_ctx->tx_lock);
+	if (ret)
+		return ret;
 	lock_sock(sk);
 	ret = tls_sw_do_sendpage(sk, page, offset, size, flags);
 	release_sock(sk);
@@ -1340,15 +1373,14 @@
 	return skb;
 }
 
-static int tls_setup_from_iter(struct sock *sk, struct iov_iter *from,
+static int tls_setup_from_iter(struct iov_iter *from,
 			       int length, int *pages_used,
-			       unsigned int *size_used,
 			       struct scatterlist *to,
 			       int to_max_pages)
 {
 	int rc = 0, i = 0, num_elem = *pages_used, maxpages;
 	struct page *pages[MAX_SKB_FRAGS];
-	unsigned int size = *size_used;
+	unsigned int size = 0;
 	ssize_t copied, use;
 	size_t offset;
 
@@ -1391,8 +1423,7 @@
 		sg_mark_end(&to[num_elem - 1]);
 out:
 	if (rc)
-		iov_iter_revert(from, size - *size_used);
-	*size_used = size;
+		iov_iter_revert(from, size);
 	*pages_used = num_elem;
 
 	return rc;
@@ -1409,12 +1440,13 @@
 static int decrypt_internal(struct sock *sk, struct sk_buff *skb,
 			    struct iov_iter *out_iov,
 			    struct scatterlist *out_sg,
-			    int *chunk, bool *zc, bool async)
+			    struct tls_decrypt_arg *darg)
 {
 	struct tls_context *tls_ctx = tls_get_ctx(sk);
 	struct tls_sw_context_rx *ctx = tls_sw_ctx_rx(tls_ctx);
 	struct tls_prot_info *prot = &tls_ctx->prot_info;
 	struct strp_msg *rxm = strp_msg(skb);
+	struct tls_msg *tlm = tls_msg(skb);
 	int n_sgin, n_sgout, nsg, mem_size, aead_size, err, pages = 0;
 	struct aead_request *aead_req;
 	struct sk_buff *unused;
@@ -1425,7 +1457,7 @@
 			     prot->tail_size;
 	int iv_offset = 0;
 
-	if (*zc && (out_iov || out_sg)) {
+	if (darg->zc && (out_iov || out_sg)) {
 		if (out_iov)
 			n_sgout = iov_iter_npages(out_iov, INT_MAX) + 1;
 		else
@@ -1434,7 +1466,7 @@
 				 rxm->full_len - prot->prepend_size);
 	} else {
 		n_sgout = 0;
-		*zc = false;
+		darg->zc = false;
 		n_sgin = skb_cow_data(skb, 0, &unused);
 	}
 
@@ -1476,23 +1508,21 @@
 	err = skb_copy_bits(skb, rxm->offset + TLS_HEADER_SIZE,
 			    iv + iv_offset + prot->salt_size,
 			    prot->iv_size);
-	if (err < 0) {
-		kfree(mem);
-		return err;
-	}
+	if (err < 0)
+		goto exit_free;
 	if (prot->version == TLS_1_3_VERSION ||
 	    prot->cipher_type == TLS_CIPHER_CHACHA20_POLY1305)
 		memcpy(iv + iv_offset, tls_ctx->rx.iv,
-		       crypto_aead_ivsize(ctx->aead_recv));
+		       prot->iv_size + prot->salt_size);
 	else
 		memcpy(iv + iv_offset, tls_ctx->rx.iv, prot->salt_size);
 
-	xor_iv_with_seq(prot, iv, tls_ctx->rx.rec_seq);
+	xor_iv_with_seq(prot, iv + iv_offset, tls_ctx->rx.rec_seq);
 
 	/* Prepare AAD */
 	tls_make_aad(aad, rxm->full_len - prot->overhead_size +
 		     prot->tail_size,
-		     tls_ctx->rx.rec_seq, ctx->control, prot);
+		     tls_ctx->rx.rec_seq, tlm->control, prot);
 
 	/* Prepare sgin */
 	sg_init_table(sgin, n_sgin);
@@ -1500,19 +1530,16 @@
 	err = skb_to_sgvec(skb, &sgin[1],
 			   rxm->offset + prot->prepend_size,
 			   rxm->full_len - prot->prepend_size);
-	if (err < 0) {
-		kfree(mem);
-		return err;
-	}
+	if (err < 0)
+		goto exit_free;
 
 	if (n_sgout) {
 		if (out_iov) {
 			sg_init_table(sgout, n_sgout);
 			sg_set_buf(&sgout[0], aad, prot->aad_size);
 
-			*chunk = 0;
-			err = tls_setup_from_iter(sk, out_iov, data_len,
-						  &pages, chunk, &sgout[1],
+			err = tls_setup_from_iter(out_iov, data_len,
+						  &pages, &sgout[1],
 						  (n_sgout - 1));
 			if (err < 0)
 				goto fallback_to_reg_recv;
@@ -1525,82 +1552,89 @@
 fallback_to_reg_recv:
 		sgout = sgin;
 		pages = 0;
-		*chunk = data_len;
-		*zc = false;
+		darg->zc = false;
 	}
 
 	/* Prepare and submit AEAD request */
 	err = tls_do_decryption(sk, skb, sgin, sgout, iv,
-				data_len, aead_req, async);
-	if (err == -EINPROGRESS)
-		return err;
+				data_len, aead_req, darg);
+	if (err) {
+		if (darg->async_done)
+			return err;
+	}
+
+	if (darg->async)
+		return 0;
+
+	if (unlikely(darg->async_done))
+		return 0;
 
 	/* Release the pages in case iov was mapped to pages */
 	for (; pages > 0; pages--)
 		put_page(sg_page(&sgout[pages]));
-
+exit_free:
 	kfree(mem);
 	return err;
 }
 
 static int decrypt_skb_update(struct sock *sk, struct sk_buff *skb,
-			      struct iov_iter *dest, int *chunk, bool *zc,
-			      bool async)
+			      struct iov_iter *dest,
+			      struct tls_decrypt_arg *darg)
 {
 	struct tls_context *tls_ctx = tls_get_ctx(sk);
-	struct tls_sw_context_rx *ctx = tls_sw_ctx_rx(tls_ctx);
 	struct tls_prot_info *prot = &tls_ctx->prot_info;
 	struct strp_msg *rxm = strp_msg(skb);
-	int pad, err = 0;
+	struct tls_msg *tlm = tls_msg(skb);
+	int pad, err;
 
-	if (!ctx->decrypted) {
-		if (tls_ctx->rx_conf == TLS_HW) {
-			err = tls_device_decrypted(sk, tls_ctx, skb, rxm);
-			if (err < 0)
-				return err;
-		}
+	if (tlm->decrypted) {
+		darg->zc = false;
+		darg->async = false;
+		return 0;
+	}
 
-		/* Still not decrypted after tls_device */
-		if (!ctx->decrypted) {
-			err = decrypt_internal(sk, skb, dest, NULL, chunk, zc,
-					       async);
-			if (err < 0) {
-				if (err == -EINPROGRESS)
-					tls_advance_record_sn(sk, prot,
-							      &tls_ctx->rx);
-				else if (err == -EBADMSG)
-					TLS_INC_STATS(sock_net(sk),
-						      LINUX_MIB_TLSDECRYPTERROR);
-				return err;
-			}
-		} else {
-			*zc = false;
+	if (tls_ctx->rx_conf == TLS_HW) {
+		err = tls_device_decrypted(sk, tls_ctx, skb, rxm);
+		if (err < 0)
+			return err;
+		if (err > 0) {
+			tlm->decrypted = 1;
+			darg->zc = false;
+			darg->async = false;
+			goto decrypt_done;
 		}
+	}
 
-		pad = padding_length(ctx, prot, skb);
-		if (pad < 0)
-			return pad;
-
-		rxm->full_len -= pad;
-		rxm->offset += prot->prepend_size;
-		rxm->full_len -= prot->overhead_size;
-		tls_advance_record_sn(sk, prot, &tls_ctx->rx);
-		ctx->decrypted = 1;
-		ctx->saved_data_ready(sk);
-	} else {
-		*zc = false;
+	err = decrypt_internal(sk, skb, dest, NULL, darg);
+	if (err < 0) {
+		if (err == -EBADMSG)
+			TLS_INC_STATS(sock_net(sk), LINUX_MIB_TLSDECRYPTERROR);
+		return err;
 	}
+	if (darg->async)
+		goto decrypt_next;
 
-	return err;
+decrypt_done:
+	pad = padding_length(prot, skb);
+	if (pad < 0)
+		return pad;
+
+	rxm->full_len -= pad;
+	rxm->offset += prot->prepend_size;
+	rxm->full_len -= prot->overhead_size;
+	tlm->decrypted = 1;
+decrypt_next:
+	tls_advance_record_sn(sk, prot, &tls_ctx->rx);
+
+	return 0;
 }
 
 int decrypt_skb(struct sock *sk, struct sk_buff *skb,
 		struct scatterlist *sgout)
 {
-	bool zc = true;
-	int chunk;
+	struct tls_decrypt_arg darg = { .zc = true, };
 
-	return decrypt_internal(sk, skb, NULL, sgout, &chunk, &zc, false);
+	return decrypt_internal(sk, skb, NULL, sgout, &darg);
 }
 
 static bool tls_sw_advance_skb(struct sock *sk, struct sk_buff *skb,
@@ -1627,6 +1661,29 @@
 	return true;
 }
 
+static int tls_record_content_type(struct msghdr *msg, struct tls_msg *tlm,
+				   u8 *control)
+{
+	int err;
+
+	if (!*control) {
+		*control = tlm->control;
+		if (!*control)
+			return -EBADMSG;
+
+		err = put_cmsg(msg, SOL_TLS, TLS_GET_RECORD_TYPE,
+			       sizeof(*control), control);
+		if (*control != TLS_RECORD_TYPE_DATA) {
+			if (err || msg->msg_flags & MSG_CTRUNC)
+				return -EIO;
+		}
+	} else if (*control != tlm->control) {
+		return 0;
+	}
+
+	return 1;
+}
+
 /* This function traverses the rx_list in tls receive context to copies the
  * decrypted records into the buffer provided by caller zero copy is not
  * true. Further, the records are removed from the rx_list if it is not a peek
@@ -1635,31 +1692,23 @@
 static int process_rx_list(struct tls_sw_context_rx *ctx,
 			   struct msghdr *msg,
 			   u8 *control,
-			   bool *cmsg,
 			   size_t skip,
 			   size_t len,
 			   bool zc,
 			   bool is_peek)
 {
 	struct sk_buff *skb = skb_peek(&ctx->rx_list);
-	u8 ctrl = *control;
-	u8 msgc = *cmsg;
 	struct tls_msg *tlm;
 	ssize_t copied = 0;
-
-	/* Set the record type in 'control' if caller didn't pass it */
-	if (!ctrl && skb) {
-		tlm = tls_msg(skb);
-		ctrl = tlm->control;
-	}
+	int err;
 
 	while (skip && skb) {
 		struct strp_msg *rxm = strp_msg(skb);
 		tlm = tls_msg(skb);
 
-		/* Cannot process a record of different type */
-		if (ctrl != tlm->control)
-			return 0;
+		err = tls_record_content_type(msg, tlm, control);
+		if (err <= 0)
+			return err;
 
 		if (skip < rxm->full_len)
 			break;
@@ -1675,27 +1724,12 @@
 
 		tlm = tls_msg(skb);
 
-		/* Cannot process a record of different type */
-		if (ctrl != tlm->control)
-			return 0;
-
-		/* Set record type if not already done. For a non-data record,
-		 * do not proceed if record type could not be copied.
-		 */
-		if (!msgc) {
-			int cerr = put_cmsg(msg, SOL_TLS, TLS_GET_RECORD_TYPE,
-					    sizeof(ctrl), &ctrl);
-			msgc = true;
-			if (ctrl != TLS_RECORD_TYPE_DATA) {
-				if (cerr || msg->msg_flags & MSG_CTRUNC)
-					return -EIO;
-
-				*cmsg = msgc;
-			}
-		}
+		err = tls_record_content_type(msg, tlm, control);
+		if (err <= 0)
+			return err;
 
 		if (!zc || (rxm->full_len - skip) > len) {
-			int err = skb_copy_datagram_msg(skb, rxm->offset + skip,
+			err = skb_copy_datagram_msg(skb, rxm->offset + skip,
 						    msg, chunk);
 			if (err < 0)
 				return err;
@@ -1732,10 +1766,63 @@
 		skb = next_skb;
 	}
 
-	*control = ctrl;
 	return copied;
 }
 
+static long tls_rx_reader_lock(struct sock *sk, struct tls_sw_context_rx *ctx,
+			       bool nonblock)
+{
+	long timeo;
+	int err;
+
+	lock_sock(sk);
+
+	timeo = sock_rcvtimeo(sk, nonblock);
+
+	while (unlikely(ctx->reader_present)) {
+		DEFINE_WAIT_FUNC(wait, woken_wake_function);
+
+		ctx->reader_contended = 1;
+
+		add_wait_queue(&ctx->wq, &wait);
+		sk_wait_event(sk, &timeo,
+			      !READ_ONCE(ctx->reader_present), &wait);
+		remove_wait_queue(&ctx->wq, &wait);
+
+		if (timeo <= 0) {
+			err = -EAGAIN;
+			goto err_unlock;
+		}
+		if (signal_pending(current)) {
+			err = sock_intr_errno(timeo);
+			goto err_unlock;
+		}
+	}
+
+	WRITE_ONCE(ctx->reader_present, 1);
+
+	return timeo;
+
+err_unlock:
+	release_sock(sk);
+	return err;
+}
+
+static void tls_rx_reader_unlock(struct sock *sk, struct tls_sw_context_rx *ctx)
+{
+	if (unlikely(ctx->reader_contended)) {
+		if (wq_has_sleeper(&ctx->wq))
+			wake_up(&ctx->wq);
+		else
+			ctx->reader_contended = 0;
+
+		WARN_ON_ONCE(!ctx->reader_present);
+	}
+
+	WRITE_ONCE(ctx->reader_present, 0);
+	release_sock(sk);
+}
+
 int tls_sw_recvmsg(struct sock *sk,
 		   struct msghdr *msg,
 		   size_t len,
@@ -1753,14 +1840,12 @@
 	struct tls_msg *tlm;
 	struct sk_buff *skb;
 	ssize_t copied = 0;
-	bool cmsg = false;
+	bool async = false;
 	int target, err = 0;
 	long timeo;
 	bool is_kvec = iov_iter_is_kvec(&msg->msg_iter);
 	bool is_peek = flags & MSG_PEEK;
 	bool bpf_strp_enabled;
-	int num_async = 0;
-	int pending;
 
 	flags |= nonblock;
 
@@ -1768,33 +1853,35 @@
 		return sock_recv_errqueue(sk, msg, len, SOL_IP, IP_RECVERR);
 
 	psock = sk_psock_get(sk);
-	lock_sock(sk);
+	timeo = tls_rx_reader_lock(sk, ctx, flags & MSG_DONTWAIT);
+	if (timeo < 0)
+		return timeo;
 	bpf_strp_enabled = sk_psock_strp_enabled(psock);
 
+	/* If crypto failed the connection is broken */
+	err = ctx->async_wait.err;
+	if (err)
+		goto end;
+
 	/* Process pending decrypted records. It must be non-zero-copy */
-	err = process_rx_list(ctx, msg, &control, &cmsg, 0, len, false,
-			      is_peek);
+	err = process_rx_list(ctx, msg, &control, 0, len, false, is_peek);
 	if (err < 0) {
 		tls_err_abort(sk, err);
 		goto end;
-	} else {
-		copied = err;
 	}
 
-	if (len <= copied)
-		goto recv_end;
+	copied = err;
+	if (len <= copied || (copied && control != TLS_RECORD_TYPE_DATA))
+		goto end;
 
 	target = sock_rcvlowat(sk, flags & MSG_WAITALL, len);
 	len = len - copied;
-	timeo = sock_rcvtimeo(sk, flags & MSG_DONTWAIT);
 
+	decrypted = 0;
 	while (len && (decrypted + copied < target || ctx->recv_pkt)) {
+		struct tls_decrypt_arg darg = {};
 		bool retain_skb = false;
-		bool zc = false;
-		int to_decrypt;
-		int chunk = 0;
-		bool async_capable;
-		bool async = false;
+		int to_decrypt, chunk;
 
 		skb = tls_wait_data(sk, psock, flags & MSG_DONTWAIT, timeo, &err);
 		if (!skb) {
@@ -1809,43 +1896,32 @@
 				}
 			}
 			goto recv_end;
-		} else {
-			tlm = tls_msg(skb);
-			if (prot->version == TLS_1_3_VERSION)
-				tlm->control = 0;
-			else
-				tlm->control = ctx->control;
 		}
 
 		rxm = strp_msg(skb);
+		tlm = tls_msg(skb);
 
 		to_decrypt = rxm->full_len - prot->overhead_size;
 
 		if (to_decrypt <= len && !is_kvec && !is_peek &&
-		    ctx->control == TLS_RECORD_TYPE_DATA &&
+		    tlm->control == TLS_RECORD_TYPE_DATA &&
 		    prot->version != TLS_1_3_VERSION &&
 		    !bpf_strp_enabled)
-			zc = true;
+			darg.zc = true;
 
 		/* Do not use async mode if record is non-data */
-		if (ctx->control == TLS_RECORD_TYPE_DATA && !bpf_strp_enabled)
-			async_capable = ctx->async_capable;
+		if (tlm->control == TLS_RECORD_TYPE_DATA && !bpf_strp_enabled)
+			darg.async = ctx->async_capable;
 		else
-			async_capable = false;
+			darg.async = false;
 
-		err = decrypt_skb_update(sk, skb, &msg->msg_iter,
-					 &chunk, &zc, async_capable);
-		if (err < 0 && err != -EINPROGRESS) {
+		err = decrypt_skb_update(sk, skb, &msg->msg_iter, &darg);
+		if (err < 0) {
 			tls_err_abort(sk, -EBADMSG);
 			goto recv_end;
 		}
 
-		if (err == -EINPROGRESS) {
-			async = true;
-			num_async++;
-		} else if (prot->version == TLS_1_3_VERSION) {
-			tlm->control = ctx->control;
-		}
+		async |= darg.async;
 
 		/* If the type of records being processed is not known yet,
 		 * set it to record type just dequeued. If it is already known,
@@ -1854,30 +1930,19 @@
 		 * is known just after record is dequeued from stream parser.
 		 * For tls1.3, we disable async.
 		 */
-
-		if (!control)
-			control = tlm->control;
-		else if (control != tlm->control)
+		err = tls_record_content_type(msg, tlm, &control);
+		if (err <= 0)
 			goto recv_end;
 
-		if (!cmsg) {
-			int cerr;
-
-			cerr = put_cmsg(msg, SOL_TLS, TLS_GET_RECORD_TYPE,
-					sizeof(control), &control);
-			cmsg = true;
-			if (control != TLS_RECORD_TYPE_DATA) {
-				if (cerr || msg->msg_flags & MSG_CTRUNC) {
-					err = -EIO;
-					goto recv_end;
-				}
-			}
-		}
-
-		if (async)
+		if (async) {
+			/* TLS 1.2-only, to_decrypt must be text length */
+			chunk = min_t(int, to_decrypt, len);
 			goto pick_next_record;
+		}
+		/* TLS 1.3 may have updated the length by more than overhead */
+		chunk = rxm->full_len;
 
-		if (!zc) {
+		if (!darg.zc) {
 			if (bpf_strp_enabled) {
 				err = sk_psock_tls_strp_read(psock, skb);
 				if (err != __SK_PASS) {
@@ -1891,11 +1956,9 @@
 				}
 			}
 
-			if (rxm->full_len > len) {
+			if (chunk > len) {
 				retain_skb = true;
 				chunk = len;
-			} else {
-				chunk = rxm->full_len;
 			}
 
 			err = skb_copy_datagram_msg(skb, rxm->offset,
@@ -1910,9 +1973,6 @@
 		}
 
 pick_next_record:
-		if (chunk > len)
-			chunk = len;
-
 		decrypted += chunk;
 		len -= chunk;
 
@@ -1936,36 +1996,25 @@
 	}
 
 recv_end:
-	if (num_async) {
+	if (async) {
+		int ret;
+
 		/* Wait for all previously submitted records to be decrypted */
-		spin_lock_bh(&ctx->decrypt_compl_lock);
-		ctx->async_notify = true;
-		pending = atomic_read(&ctx->decrypt_pending);
-		spin_unlock_bh(&ctx->decrypt_compl_lock);
-		if (pending) {
-			err = crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
-			if (err) {
-				/* one of async decrypt failed */
-				tls_err_abort(sk, err);
-				copied = 0;
-				decrypted = 0;
-				goto end;
-			}
-		} else {
-			reinit_completion(&ctx->async_wait.completion);
-		}
+		ret = tls_decrypt_async_wait(ctx);
 
-		/* There can be no concurrent accesses, since we have no
-		 * pending decrypt operations
-		 */
-		WRITE_ONCE(ctx->async_notify, false);
+		if (ret) {
+			if (err >= 0 || err == -EINPROGRESS)
+				err = ret;
+			decrypted = 0;
+			goto end;
+		}
 
 		/* Drain records from the rx_list & copy if required */
 		if (is_peek || is_kvec)
-			err = process_rx_list(ctx, msg, &control, &cmsg, copied,
+			err = process_rx_list(ctx, msg, &control, copied,
 					      decrypted, false, is_peek);
 		else
-			err = process_rx_list(ctx, msg, &control, &cmsg, 0,
+			err = process_rx_list(ctx, msg, &control, 0,
 					      decrypted, true, is_peek);
 		if (err < 0) {
 			tls_err_abort(sk, err);
@@ -1977,7 +2026,7 @@
 	copied += decrypted;
 
 end:
-	release_sock(sk);
+	tls_rx_reader_unlock(sk, ctx);
 	if (psock)
 		sk_psock_put(sk, psock);
 	return copied ? : err;
@@ -1991,47 +2040,64 @@
 	struct tls_sw_context_rx *ctx = tls_sw_ctx_rx(tls_ctx);
 	struct strp_msg *rxm = NULL;
 	struct sock *sk = sock->sk;
+	struct tls_msg *tlm;
 	struct sk_buff *skb;
 	ssize_t copied = 0;
+	bool from_queue;
 	int err = 0;
 	long timeo;
 	int chunk;
-	bool zc = false;
-
-	lock_sock(sk);
-
-	timeo = sock_rcvtimeo(sk, flags & SPLICE_F_NONBLOCK);
-
-	skb = tls_wait_data(sk, NULL, flags & SPLICE_F_NONBLOCK, timeo, &err);
-	if (!skb)
-		goto splice_read_end;
 
-	if (!ctx->decrypted) {
-		err = decrypt_skb_update(sk, skb, NULL, &chunk, &zc, false);
+	timeo = tls_rx_reader_lock(sk, ctx, flags & SPLICE_F_NONBLOCK);
+	if (timeo < 0)
+		return timeo;
+
+	from_queue = !skb_queue_empty(&ctx->rx_list);
+	if (from_queue) {
+		skb = __skb_dequeue(&ctx->rx_list);
+	} else {
+		struct tls_decrypt_arg darg = {};
 
-		/* splice does not support reading control messages */
-		if (ctx->control != TLS_RECORD_TYPE_DATA) {
-			err = -EINVAL;
+		skb = tls_wait_data(sk, NULL, flags & SPLICE_F_NONBLOCK, timeo,
+				    &err);
+		if (!skb)
 			goto splice_read_end;
-		}
 
+		err = decrypt_skb_update(sk, skb, NULL, &darg);
 		if (err < 0) {
 			tls_err_abort(sk, -EBADMSG);
 			goto splice_read_end;
 		}
-		ctx->decrypted = 1;
 	}
+
 	rxm = strp_msg(skb);
+	tlm = tls_msg(skb);
+
+	/* splice does not support reading control messages */
+	if (tlm->control != TLS_RECORD_TYPE_DATA) {
+		err = -EINVAL;
+		goto splice_read_end;
+	}
 
 	chunk = min_t(unsigned int, rxm->full_len, len);
 	copied = skb_splice_bits(skb, sk, rxm->offset, pipe, chunk, flags);
 	if (copied < 0)
 		goto splice_read_end;
 
-	tls_sw_advance_skb(sk, skb, copied);
+	if (!from_queue) {
+		ctx->recv_pkt = NULL;
+		__strp_unpause(&ctx->strp);
+	}
+	if (chunk < rxm->full_len) {
+		__skb_queue_head(&ctx->rx_list, skb);
+		rxm->offset += len;
+		rxm->full_len -= len;
+	} else {
+		consume_skb(skb);
+	}
 
 splice_read_end:
-	release_sock(sk);
+	tls_rx_reader_unlock(sk, ctx);
 	return copied ? : err;
 }
 
@@ -2055,10 +2121,10 @@
 static int tls_read_size(struct strparser *strp, struct sk_buff *skb)
 {
 	struct tls_context *tls_ctx = tls_get_ctx(strp->sk);
-	struct tls_sw_context_rx *ctx = tls_sw_ctx_rx(tls_ctx);
 	struct tls_prot_info *prot = &tls_ctx->prot_info;
 	char header[TLS_HEADER_SIZE + MAX_IV_SIZE];
 	struct strp_msg *rxm = strp_msg(skb);
+	struct tls_msg *tlm = tls_msg(skb);
 	size_t cipher_overhead;
 	size_t data_len = 0;
 	int ret;
@@ -2079,7 +2145,7 @@
 	if (ret < 0)
 		goto read_failure;
 
-	ctx->control = header[0];
+	tlm->control = header[0];
 
 	data_len = ((header[4] & 0xFF) | (header[3] << 8));
 
@@ -2119,8 +2185,9 @@
 {
 	struct tls_context *tls_ctx = tls_get_ctx(strp->sk);
 	struct tls_sw_context_rx *ctx = tls_sw_ctx_rx(tls_ctx);
+	struct tls_msg *tlm = tls_msg(skb);
 
-	ctx->decrypted = 0;
+	tlm->decrypted = 0;
 
 	ctx->recv_pkt = skb;
 	strp_pause(strp);
@@ -2158,16 +2225,9 @@
 	struct tls_context *tls_ctx = tls_get_ctx(sk);
 	struct tls_sw_context_tx *ctx = tls_sw_ctx_tx(tls_ctx);
 	struct tls_rec *rec, *tmp;
-	int pending;
 
 	/* Wait for any pending async encryptions to complete */
-	spin_lock_bh(&ctx->encrypt_compl_lock);
-	ctx->async_notify = true;
-	pending = atomic_read(&ctx->encrypt_pending);
-	spin_unlock_bh(&ctx->encrypt_compl_lock);
-
-	if (pending)
-		crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
+	tls_encrypt_async_wait(ctx);
 
 	tls_tx_records(sk, -1);
 
@@ -2268,11 +2328,19 @@
 
 	if (!test_and_clear_bit(BIT_TX_SCHEDULED, &ctx->tx_bitmask))
 		return;
-	mutex_lock(&tls_ctx->tx_lock);
-	lock_sock(sk);
-	tls_tx_records(sk, -1);
-	release_sock(sk);
-	mutex_unlock(&tls_ctx->tx_lock);
+
+	if (mutex_trylock(&tls_ctx->tx_lock)) {
+		lock_sock(sk);
+		tls_tx_records(sk, -1);
+		release_sock(sk);
+		mutex_unlock(&tls_ctx->tx_lock);
+	} else if (!test_and_set_bit(BIT_TX_SCHEDULED, &ctx->tx_bitmask)) {
+		/* Someone is holding the tx_lock, they will likely run Tx
+		 * and cancel the work on their way out of the lock section.
+		 * Schedule a long delay just in case.
+		 */
+		schedule_delayed_work(&ctx->tx_work.work, msecs_to_jiffies(10));
+	}
 }
 
 void tls_sw_write_space(struct sock *sk, struct tls_context *ctx)
@@ -2297,6 +2365,47 @@
 	strp_check_rcv(&rx_ctx->strp);
 }
 
+static struct tls_sw_context_tx *init_ctx_tx(struct tls_context *ctx, struct sock *sk)
+{
+	struct tls_sw_context_tx *sw_ctx_tx;
+
+	if (!ctx->priv_ctx_tx) {
+		sw_ctx_tx = kzalloc(sizeof(*sw_ctx_tx), GFP_KERNEL);
+		if (!sw_ctx_tx)
+			return NULL;
+	} else {
+		sw_ctx_tx = ctx->priv_ctx_tx;
+	}
+
+	crypto_init_wait(&sw_ctx_tx->async_wait);
+	atomic_set(&sw_ctx_tx->encrypt_pending, 1);
+	INIT_LIST_HEAD(&sw_ctx_tx->tx_list);
+	INIT_DELAYED_WORK(&sw_ctx_tx->tx_work.work, tx_work_handler);
+	sw_ctx_tx->tx_work.sk = sk;
+
+	return sw_ctx_tx;
+}
+
+static struct tls_sw_context_rx *init_ctx_rx(struct tls_context *ctx)
+{
+	struct tls_sw_context_rx *sw_ctx_rx;
+
+	if (!ctx->priv_ctx_rx) {
+		sw_ctx_rx = kzalloc(sizeof(*sw_ctx_rx), GFP_KERNEL);
+		if (!sw_ctx_rx)
+			return NULL;
+	} else {
+		sw_ctx_rx = ctx->priv_ctx_rx;
+	}
+
+	crypto_init_wait(&sw_ctx_rx->async_wait);
+	atomic_set(&sw_ctx_rx->decrypt_pending, 1);
+	init_waitqueue_head(&sw_ctx_rx->wq);
+	skb_queue_head_init(&sw_ctx_rx->rx_list);
+
+	return sw_ctx_rx;
+}
+
 int tls_set_sw_offload(struct sock *sk, struct tls_context *ctx, int tx)
 {
 	struct tls_context *tls_ctx = tls_get_ctx(sk);
@@ -2323,46 +2432,22 @@
 	}
 
 	if (tx) {
-		if (!ctx->priv_ctx_tx) {
-			sw_ctx_tx = kzalloc(sizeof(*sw_ctx_tx), GFP_KERNEL);
-			if (!sw_ctx_tx) {
-				rc = -ENOMEM;
-				goto out;
-			}
-			ctx->priv_ctx_tx = sw_ctx_tx;
-		} else {
-			sw_ctx_tx =
-				(struct tls_sw_context_tx *)ctx->priv_ctx_tx;
-		}
-	} else {
-		if (!ctx->priv_ctx_rx) {
-			sw_ctx_rx = kzalloc(sizeof(*sw_ctx_rx), GFP_KERNEL);
-			if (!sw_ctx_rx) {
-				rc = -ENOMEM;
-				goto out;
-			}
-			ctx->priv_ctx_rx = sw_ctx_rx;
-		} else {
-			sw_ctx_rx =
-				(struct tls_sw_context_rx *)ctx->priv_ctx_rx;
-		}
-	}
+		ctx->priv_ctx_tx = init_ctx_tx(ctx, sk);
+		if (!ctx->priv_ctx_tx)
+			return -ENOMEM;
 
-	if (tx) {
-		crypto_init_wait(&sw_ctx_tx->async_wait);
-		spin_lock_init(&sw_ctx_tx->encrypt_compl_lock);
+		sw_ctx_tx = ctx->priv_ctx_tx;
 		crypto_info = &ctx->crypto_send.info;
 		cctx = &ctx->tx;
 		aead = &sw_ctx_tx->aead_send;
-		INIT_LIST_HEAD(&sw_ctx_tx->tx_list);
-		INIT_DELAYED_WORK(&sw_ctx_tx->tx_work.work, tx_work_handler);
-		sw_ctx_tx->tx_work.sk = sk;
 	} else {
-		crypto_init_wait(&sw_ctx_rx->async_wait);
-		spin_lock_init(&sw_ctx_rx->decrypt_compl_lock);
+		ctx->priv_ctx_rx = init_ctx_rx(ctx);
+		if (!ctx->priv_ctx_rx)
+			return -ENOMEM;
+
+		sw_ctx_rx = ctx->priv_ctx_rx;
 		crypto_info = &ctx->crypto_recv.info;
 		cctx = &ctx->rx;
-		skb_queue_head_init(&sw_ctx_rx->rx_list);
 		aead = &sw_ctx_rx->aead_recv;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/unix/af_unix.c
+++ linux-xilinx-zynqmp-5.15.0/net/unix/af_unix.c
@@ -139,17 +139,17 @@
 #ifdef CONFIG_SECURITY_NETWORK
 static void unix_get_secdata(struct scm_cookie *scm, struct sk_buff *skb)
 {
-	UNIXCB(skb).secid = scm->secid;
+	UNIXCB(skb).lsmblob = scm->lsmblob;
 }
 
 static inline void unix_set_secdata(struct scm_cookie *scm, struct sk_buff *skb)
 {
-	scm->secid = UNIXCB(skb).secid;
+	scm->lsmblob = UNIXCB(skb).lsmblob;
 }
 
 static inline bool unix_secdata_eq(struct scm_cookie *scm, struct sk_buff *skb)
 {
-	return (scm->secid == UNIXCB(skb).secid);
+	return lsmblob_equal(&scm->lsmblob, &(UNIXCB(skb).lsmblob));
 }
 #else
 static inline void unix_get_secdata(struct scm_cookie *scm, struct sk_buff *skb)
@@ -190,15 +190,9 @@
 	return unix_peer(osk) == NULL || unix_our_peer(sk, osk);
 }
 
-static inline int unix_recvq_full(const struct sock *sk)
-{
-	return skb_queue_len(&sk->sk_receive_queue) > sk->sk_max_ack_backlog;
-}
-
 static inline int unix_recvq_full_lockless(const struct sock *sk)
 {
-	return skb_queue_len_lockless(&sk->sk_receive_queue) >
-		READ_ONCE(sk->sk_max_ack_backlog);
+	return skb_queue_len_lockless(&sk->sk_receive_queue) > sk->sk_max_ack_backlog;
 }
 
 struct sock *unix_peer_get(struct sock *s)
@@ -446,7 +440,7 @@
 	 * -ECONNREFUSED. Otherwise, if we haven't queued any skbs
 	 * to other and its full, we will hang waiting for POLLOUT.
 	 */
-	if (unix_recvq_full(other) && !sock_flag(other, SOCK_DEAD))
+	if (unix_recvq_full_lockless(other) && !sock_flag(other, SOCK_DEAD))
 		return 1;
 
 	if (connected)
@@ -455,9 +449,9 @@
 	return 0;
 }
 
-static int unix_writable(const struct sock *sk)
+static int unix_writable(const struct sock *sk, unsigned char state)
 {
-	return sk->sk_state != TCP_LISTEN &&
+	return state != TCP_LISTEN &&
 	       (refcount_read(&sk->sk_wmem_alloc) << 2) <= sk->sk_sndbuf;
 }
 
@@ -466,7 +460,7 @@
 	struct socket_wq *wq;
 
 	rcu_read_lock();
-	if (unix_writable(sk)) {
+	if (unix_writable(sk, READ_ONCE(sk->sk_state))) {
 		wq = rcu_dereference(sk->sk_wq);
 		if (skwq_has_sleeper(wq))
 			wake_up_interruptible_sync_poll(&wq->wait,
@@ -491,11 +485,10 @@
 		 * when peer was not connected to us.
 		 */
 		if (!sock_flag(other, SOCK_DEAD) && unix_peer(other) == sk) {
-			other->sk_err = ECONNRESET;
+			WRITE_ONCE(other->sk_err, ECONNRESET);
 			sk_error_report(other);
 		}
 	}
-	other->sk_state = TCP_CLOSE;
 }
 
 static void unix_sock_destructor(struct sock *sk)
@@ -504,12 +497,6 @@
 
 	skb_queue_purge(&sk->sk_receive_queue);
 
-#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
-	if (u->oob_skb) {
-		kfree_skb(u->oob_skb);
-		u->oob_skb = NULL;
-	}
-#endif
 	WARN_ON(refcount_read(&sk->sk_wmem_alloc));
 	WARN_ON(!sk_unhashed(sk));
 	WARN_ON(sk->sk_socket);
@@ -522,9 +509,7 @@
 		unix_release_addr(u->addr);
 
 	atomic_long_dec(&unix_nr_socks);
-	local_bh_disable();
 	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, -1);
-	local_bh_enable();
 #ifdef UNIX_REFCNT_DEBUG
 	pr_debug("UNIX %p is destroyed, %ld are still alive.\n", sk,
 		atomic_long_read(&unix_nr_socks));
@@ -544,27 +529,34 @@
 	/* Clear state */
 	unix_state_lock(sk);
 	sock_orphan(sk);
-	sk->sk_shutdown = SHUTDOWN_MASK;
+	WRITE_ONCE(sk->sk_shutdown, SHUTDOWN_MASK);
 	path	     = u->path;
 	u->path.dentry = NULL;
 	u->path.mnt = NULL;
 	state = sk->sk_state;
-	sk->sk_state = TCP_CLOSE;
+	WRITE_ONCE(sk->sk_state, TCP_CLOSE);
 
 	skpair = unix_peer(sk);
 	unix_peer(sk) = NULL;
 
 	unix_state_unlock(sk);
 
+#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
+	if (u->oob_skb) {
+		kfree_skb(u->oob_skb);
+		u->oob_skb = NULL;
+	}
+#endif
+
 	wake_up_interruptible_all(&u->peer_wait);
 
 	if (skpair != NULL) {
 		if (sk->sk_type == SOCK_STREAM || sk->sk_type == SOCK_SEQPACKET) {
 			unix_state_lock(skpair);
 			/* No more writes */
-			skpair->sk_shutdown = SHUTDOWN_MASK;
-			if (!skb_queue_empty(&sk->sk_receive_queue) || embrion)
-				skpair->sk_err = ECONNRESET;
+			WRITE_ONCE(skpair->sk_shutdown, SHUTDOWN_MASK);
+			if (!skb_queue_empty_lockless(&sk->sk_receive_queue) || embrion)
+				WRITE_ONCE(skpair->sk_err, ECONNRESET);
 			unix_state_unlock(skpair);
 			skpair->sk_state_change(skpair);
 			sk_wake_async(skpair, SOCK_WAKE_WAITD, POLL_HUP);
@@ -602,7 +594,7 @@
 	 *	  What the above comment does talk about? --ANK(980817)
 	 */
 
-	if (unix_tot_inflight)
+	if (READ_ONCE(unix_tot_inflight))
 		unix_gc();		/* Garbage collect fds */
 }
 
@@ -624,9 +616,6 @@
 
 static void copy_peercred(struct sock *sk, struct sock *peersk)
 {
-	const struct cred *old_cred;
-	struct pid *old_pid;
-
 	if (sk < peersk) {
 		spin_lock(&sk->sk_peer_lock);
 		spin_lock_nested(&peersk->sk_peer_lock, SINGLE_DEPTH_NESTING);
@@ -634,16 +623,12 @@
 		spin_lock(&peersk->sk_peer_lock);
 		spin_lock_nested(&sk->sk_peer_lock, SINGLE_DEPTH_NESTING);
 	}
-	old_pid = sk->sk_peer_pid;
-	old_cred = sk->sk_peer_cred;
+
 	sk->sk_peer_pid  = get_pid(peersk->sk_peer_pid);
 	sk->sk_peer_cred = get_cred(peersk->sk_peer_cred);
 
 	spin_unlock(&sk->sk_peer_lock);
 	spin_unlock(&peersk->sk_peer_lock);
-
-	put_pid(old_pid);
-	put_cred(old_cred);
 }
 
 static int unix_listen(struct socket *sock, int backlog)
@@ -664,7 +649,8 @@
 	if (backlog > sk->sk_max_ack_backlog)
 		wake_up_interruptible_all(&u->peer_wait);
 	sk->sk_max_ack_backlog	= backlog;
-	sk->sk_state		= TCP_LISTEN;
+	WRITE_ONCE(sk->sk_state, TCP_LISTEN);
+
 	/* set credentials so connect can copy them */
 	init_peercred(sk);
 	err = 0;
@@ -716,7 +702,7 @@
 	if (mutex_lock_interruptible(&u->iolock))
 		return -EINTR;
 
-	sk->sk_peek_off = val;
+	WRITE_ONCE(sk->sk_peek_off, val);
 	mutex_unlock(&u->iolock);
 
 	return 0;
@@ -874,13 +860,13 @@
 
 	sk->sk_allocation	= GFP_KERNEL_ACCOUNT;
 	sk->sk_write_space	= unix_write_space;
-	sk->sk_max_ack_backlog	= net->unx.sysctl_max_dgram_qlen;
+	sk->sk_max_ack_backlog	= READ_ONCE(net->unx.sysctl_max_dgram_qlen);
 	sk->sk_destruct		= unix_sock_destructor;
-	u	  = unix_sk(sk);
+	u = unix_sk(sk);
+	u->inflight = 0;
 	u->path.dentry = NULL;
 	u->path.mnt = NULL;
 	spin_lock_init(&u->lock);
-	atomic_long_set(&u->inflight, 0);
 	INIT_LIST_HEAD(&u->link);
 	mutex_init(&u->iolock); /* single task reading lock */
 	mutex_init(&u->bindlock); /* single task binding lock */
@@ -889,9 +875,7 @@
 	memset(&u->scm_stat, 0, sizeof(struct scm_stat));
 	unix_insert_socket(unix_sockets_unbound(sk), sk);
 
-	local_bh_disable();
 	sock_prot_inuse_add(sock_net(sk), sk->sk_prot, 1);
-	local_bh_enable();
 
 	return sk;
 
@@ -1191,13 +1175,11 @@
 		unix_state_lock(sk1);
 		return;
 	}
-	if (sk1 < sk2) {
-		unix_state_lock(sk1);
-		unix_state_lock_nested(sk2);
-	} else {
-		unix_state_lock(sk2);
-		unix_state_lock_nested(sk1);
-	}
+	if (sk1 > sk2)
+		swap(sk1, sk2);
+
+	unix_state_lock(sk1);
+	unix_state_lock_nested(sk2, U_LOCK_SECOND);
 }
 
 static void unix_state_double_unlock(struct sock *sk1, struct sock *sk2)
@@ -1256,7 +1238,8 @@
 		if (err)
 			goto out_unlock;
 
-		sk->sk_state = other->sk_state = TCP_ESTABLISHED;
+		WRITE_ONCE(sk->sk_state, TCP_ESTABLISHED);
+		WRITE_ONCE(other->sk_state, TCP_ESTABLISHED);
 	} else {
 		/*
 		 *	1003.1g breaking connected state with AF_UNSPEC
@@ -1273,13 +1256,20 @@
 
 		unix_peer(sk) = other;
 		if (!other)
-			sk->sk_state = TCP_CLOSE;
+			WRITE_ONCE(sk->sk_state, TCP_CLOSE);
 		unix_dgram_peer_wake_disconnect_wakeup(sk, old_peer);
 
 		unix_state_double_unlock(sk, other);
 
-		if (other != old_peer)
+		if (other != old_peer) {
 			unix_dgram_disconnected(sk, old_peer);
+
+			unix_state_lock(old_peer);
+			if (!unix_peer(old_peer))
+				WRITE_ONCE(old_peer->sk_state, TCP_CLOSE);
+			unix_state_unlock(old_peer);
+		}
+
 		sock_put(old_peer);
 	} else {
 		unix_peer(sk) = other;
@@ -1306,7 +1296,7 @@
 
 	sched = !sock_flag(other, SOCK_DEAD) &&
 		!(other->sk_shutdown & RCV_SHUTDOWN) &&
-		unix_recvq_full(other);
+		unix_recvq_full_lockless(other);
 
 	unix_state_unlock(other);
 
@@ -1328,7 +1318,6 @@
 	struct sock *other = NULL;
 	struct sk_buff *skb = NULL;
 	unsigned int hash;
-	int st;
 	int err;
 	long timeo;
 
@@ -1385,7 +1374,7 @@
 	if (other->sk_shutdown & RCV_SHUTDOWN)
 		goto out_unlock;
 
-	if (unix_recvq_full(other)) {
+	if (unix_recvq_full_lockless(other)) {
 		err = -EAGAIN;
 		if (!timeo)
 			goto out_unlock;
@@ -1410,9 +1399,7 @@
 
 	   Well, and we have to recheck the state after socket locked.
 	 */
-	st = sk->sk_state;
-
-	switch (st) {
+	switch (READ_ONCE(sk->sk_state)) {
 	case TCP_CLOSE:
 		/* This is ok... continue with connect */
 		break;
@@ -1425,9 +1412,9 @@
 		goto out_unlock;
 	}
 
-	unix_state_lock_nested(sk);
+	unix_state_lock_nested(sk, U_LOCK_SECOND);
 
-	if (sk->sk_state != st) {
+	if (sk->sk_state != TCP_CLOSE) {
 		unix_state_unlock(sk);
 		unix_state_unlock(other);
 		sock_put(other);
@@ -1479,7 +1466,7 @@
 	copy_peercred(sk, other);
 
 	sock->state	= SS_CONNECTED;
-	sk->sk_state	= TCP_ESTABLISHED;
+	WRITE_ONCE(sk->sk_state, TCP_ESTABLISHED);
 	sock_hold(newsk);
 
 	smp_mb__after_atomic();	/* sock_hold() does an atomic_inc() */
@@ -1864,13 +1851,20 @@
 			unix_state_lock(sk);
 
 		err = 0;
-		if (unix_peer(sk) == other) {
+		if (sk->sk_type == SOCK_SEQPACKET) {
+			/* We are here only when racing with unix_release_sock()
+			 * is clearing @other. Never change state to TCP_CLOSE
+			 * unlike SOCK_DGRAM wants.
+			 */
+			unix_state_unlock(sk);
+			err = -EPIPE;
+		} else if (unix_peer(sk) == other) {
 			unix_peer(sk) = NULL;
 			unix_dgram_peer_wake_disconnect_wakeup(sk, other);
 
+			WRITE_ONCE(sk->sk_state, TCP_CLOSE);
 			unix_state_unlock(sk);
 
-			sk->sk_state = TCP_CLOSE;
 			unix_dgram_disconnected(sk, other);
 			sock_put(other);
 			err = -ECONNREFUSED;
@@ -1961,8 +1955,9 @@
  */
 #define UNIX_SKB_FRAGS_SZ (PAGE_SIZE << get_order(32768))
 
-#if (IS_ENABLED(CONFIG_AF_UNIX_OOB))
-static int queue_oob(struct socket *sock, struct msghdr *msg, struct sock *other)
+#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
+static int queue_oob(struct socket *sock, struct msghdr *msg, struct sock *other,
+		     struct scm_cookie *scm, bool fds_sent)
 {
 	struct unix_sock *ousk = unix_sk(other);
 	struct sk_buff *skb;
@@ -1973,6 +1968,11 @@
 	if (!skb)
 		return err;
 
+	err = unix_scm_to_skb(scm, skb, !fds_sent);
+	if (err < 0) {
+		kfree_skb(skb);
+		return err;
+	}
 	skb_put(skb, 1);
 	err = skb_copy_datagram_from_iter(skb, 0, &msg->msg_iter, 1);
 
@@ -1993,13 +1993,15 @@
 	maybe_add_creds(skb, sock, other);
 	skb_get(skb);
 
+	scm_stat_add(other, skb);
+
+	spin_lock(&other->sk_receive_queue.lock);
 	if (ousk->oob_skb)
 		consume_skb(ousk->oob_skb);
+	WRITE_ONCE(ousk->oob_skb, skb);
+	__skb_queue_tail(&other->sk_receive_queue, skb);
+	spin_unlock(&other->sk_receive_queue.lock);
 
-	ousk->oob_skb = skb;
-
-	scm_stat_add(other, skb);
-	skb_queue_tail(&other->sk_receive_queue, skb);
 	sk_send_sigurg(other);
 	unix_state_unlock(other);
 	other->sk_data_ready(other);
@@ -2027,7 +2029,7 @@
 
 	err = -EOPNOTSUPP;
 	if (msg->msg_flags & MSG_OOB) {
-#if (IS_ENABLED(CONFIG_AF_UNIX_OOB))
+#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
 		if (len)
 			len--;
 		else
@@ -2036,7 +2038,7 @@
 	}
 
 	if (msg->msg_namelen) {
-		err = sk->sk_state == TCP_ESTABLISHED ? -EISCONN : -EOPNOTSUPP;
+		err = READ_ONCE(sk->sk_state) == TCP_ESTABLISHED ? -EISCONN : -EOPNOTSUPP;
 		goto out_err;
 	} else {
 		err = -ENOTCONN;
@@ -2045,7 +2047,7 @@
 			goto out_err;
 	}
 
-	if (sk->sk_shutdown & SEND_SHUTDOWN)
+	if (READ_ONCE(sk->sk_shutdown) & SEND_SHUTDOWN)
 		goto pipe_err;
 
 	while (sent < len) {
@@ -2098,9 +2100,9 @@
 		sent += size;
 	}
 
-#if (IS_ENABLED(CONFIG_AF_UNIX_OOB))
+#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
 	if (msg->msg_flags & MSG_OOB) {
-		err = queue_oob(sock, msg, other);
+		err = queue_oob(sock, msg, other, &scm, fds_sent);
 		if (err)
 			goto out_err;
 		sent++;
@@ -2142,6 +2144,7 @@
 
 	if (false) {
 alloc_skb:
+		spin_unlock(&other->sk_receive_queue.lock);
 		unix_state_unlock(other);
 		mutex_unlock(&unix_sk(other)->iolock);
 		newskb = sock_alloc_send_pskb(sk, 0, 0, flags & MSG_DONTWAIT,
@@ -2181,6 +2184,7 @@
 		init_scm = false;
 	}
 
+	spin_lock(&other->sk_receive_queue.lock);
 	skb = skb_peek_tail(&other->sk_receive_queue);
 	if (tail && tail == skb) {
 		skb = newskb;
@@ -2211,14 +2215,11 @@
 	refcount_add(size, &sk->sk_wmem_alloc);
 
 	if (newskb) {
-		err = unix_scm_to_skb(&scm, skb, false);
-		if (err)
-			goto err_state_unlock;
-		spin_lock(&other->sk_receive_queue.lock);
+		unix_scm_to_skb(&scm, skb, false);
 		__skb_queue_tail(&other->sk_receive_queue, newskb);
-		spin_unlock(&other->sk_receive_queue.lock);
 	}
 
+	spin_unlock(&other->sk_receive_queue.lock);
 	unix_state_unlock(other);
 	mutex_unlock(&unix_sk(other)->iolock);
 
@@ -2249,7 +2250,7 @@
 	if (err)
 		return err;
 
-	if (sk->sk_state != TCP_ESTABLISHED)
+	if (READ_ONCE(sk->sk_state) != TCP_ESTABLISHED)
 		return -ENOTCONN;
 
 	if (msg->msg_namelen)
@@ -2263,7 +2264,7 @@
 {
 	struct sock *sk = sock->sk;
 
-	if (sk->sk_state != TCP_ESTABLISHED)
+	if (READ_ONCE(sk->sk_state) != TCP_ESTABLISHED)
 		return -ENOTCONN;
 
 	return unix_dgram_recvmsg(sock, msg, size, flags);
@@ -2505,8 +2506,10 @@
 
 	mutex_lock(&u->iolock);
 	unix_state_lock(sk);
+	spin_lock(&sk->sk_receive_queue.lock);
 
 	if (sock_flag(sk, SOCK_URGINLINE) || !u->oob_skb) {
+		spin_unlock(&sk->sk_receive_queue.lock);
 		unix_state_unlock(sk);
 		mutex_unlock(&u->iolock);
 		return -EINVAL;
@@ -2514,18 +2517,20 @@
 
 	oob_skb = u->oob_skb;
 
-	if (!(state->flags & MSG_PEEK)) {
-		u->oob_skb = NULL;
-	}
+	if (!(state->flags & MSG_PEEK))
+		WRITE_ONCE(u->oob_skb, NULL);
+	else
+		skb_get(oob_skb);
 
+	spin_unlock(&sk->sk_receive_queue.lock);
 	unix_state_unlock(sk);
 
 	chunk = state->recv_actor(oob_skb, 0, chunk, state);
 
-	if (!(state->flags & MSG_PEEK)) {
+	if (!(state->flags & MSG_PEEK))
 		UNIXCB(oob_skb).consumed += 1;
-		kfree_skb(oob_skb);
-	}
+
+	consume_skb(oob_skb);
 
 	mutex_unlock(&u->iolock);
 
@@ -2546,20 +2551,34 @@
 		consume_skb(skb);
 		skb = NULL;
 	} else {
+		struct sk_buff *unlinked_skb = NULL;
+
+		spin_lock(&sk->sk_receive_queue.lock);
+
 		if (skb == u->oob_skb) {
 			if (copied) {
 				skb = NULL;
-			} else if (sock_flag(sk, SOCK_URGINLINE)) {
-				if (!(flags & MSG_PEEK)) {
-					u->oob_skb = NULL;
+			} else if (!(flags & MSG_PEEK)) {
+				if (sock_flag(sk, SOCK_URGINLINE)) {
+					WRITE_ONCE(u->oob_skb, NULL);
 					consume_skb(skb);
+				} else {
+					__skb_unlink(skb, &sk->sk_receive_queue);
+					WRITE_ONCE(u->oob_skb, NULL);
+					unlinked_skb = skb;
+					skb = skb_peek(&sk->sk_receive_queue);
 				}
-			} else if (!(flags & MSG_PEEK)) {
-				skb_unlink(skb, &sk->sk_receive_queue);
-				consume_skb(skb);
-				skb = skb_peek(&sk->sk_receive_queue);
+			} else if (!sock_flag(sk, SOCK_URGINLINE)) {
+				skb = skb_peek_next(skb, &sk->sk_receive_queue);
 			}
 		}
+
+		spin_unlock(&sk->sk_receive_queue.lock);
+
+		if (unlinked_skb) {
+			WARN_ON_ONCE(skb_unref(unlinked_skb));
+			kfree_skb(unlinked_skb);
+		}
 	}
 	return skb;
 }
@@ -2568,7 +2587,7 @@
 static int unix_stream_read_sock(struct sock *sk, read_descriptor_t *desc,
 				 sk_read_actor_t recv_actor)
 {
-	if (unlikely(sk->sk_state != TCP_ESTABLISHED))
+	if (unlikely(READ_ONCE(sk->sk_state) != TCP_ESTABLISHED))
 		return -ENOTCONN;
 
 	return unix_read_sock(sk, desc, recv_actor);
@@ -2592,7 +2611,7 @@
 	size_t size = state->size;
 	unsigned int last_len;
 
-	if (unlikely(sk->sk_state != TCP_ESTABLISHED)) {
+	if (unlikely(READ_ONCE(sk->sk_state) != TCP_ESTABLISHED)) {
 		err = -EINVAL;
 		goto out;
 	}
@@ -2631,18 +2650,16 @@
 		last = skb = skb_peek(&sk->sk_receive_queue);
 		last_len = last ? last->len : 0;
 
+again:
 #if IS_ENABLED(CONFIG_AF_UNIX_OOB)
 		if (skb) {
 			skb = manage_oob(skb, sk, flags, copied);
-			if (!skb) {
+			if (!skb && copied) {
 				unix_state_unlock(sk);
-				if (copied)
-					break;
-				goto redo;
+				break;
 			}
 		}
 #endif
-again:
 		if (skb == NULL) {
 			if (copied >= target)
 				goto unlock;
@@ -2881,10 +2898,7 @@
 	++mode;
 
 	unix_state_lock(sk);
-	sk->sk_shutdown |= mode;
-	if ((sk->sk_type == SOCK_STREAM || sk->sk_type == SOCK_SEQPACKET) &&
-	    mode == SHUTDOWN_MASK)
-		sk->sk_state = TCP_CLOSE;
+	WRITE_ONCE(sk->sk_shutdown, sk->sk_shutdown | mode);
 	other = unix_peer(sk);
 	if (other)
 		sock_hold(other);
@@ -2904,7 +2918,7 @@
 		if (mode&SEND_SHUTDOWN)
 			peer_mode |= RCV_SHUTDOWN;
 		unix_state_lock(other);
-		other->sk_shutdown |= peer_mode;
+		WRITE_ONCE(other->sk_shutdown, other->sk_shutdown | peer_mode);
 		unix_state_unlock(other);
 		other->sk_state_change(other);
 		if (peer_mode == SHUTDOWN_MASK)
@@ -2923,7 +2937,7 @@
 	struct sk_buff *skb;
 	long amount = 0;
 
-	if (sk->sk_state == TCP_LISTEN)
+	if (READ_ONCE(sk->sk_state) == TCP_LISTEN)
 		return -EINVAL;
 
 	spin_lock(&sk->sk_receive_queue.lock);
@@ -3009,11 +3023,10 @@
 	case SIOCATMARK:
 		{
 			struct sk_buff *skb;
-			struct unix_sock *u = unix_sk(sk);
 			int answ = 0;
 
 			skb = skb_peek(&sk->sk_receive_queue);
-			if (skb && skb == u->oob_skb)
+			if (skb && skb == READ_ONCE(unix_sk(sk)->oob_skb))
 				answ = 1;
 			err = put_user(answ, (int __user *)arg);
 		}
@@ -3036,17 +3049,21 @@
 static __poll_t unix_poll(struct file *file, struct socket *sock, poll_table *wait)
 {
 	struct sock *sk = sock->sk;
+	unsigned char state;
 	__poll_t mask;
+	u8 shutdown;
 
 	sock_poll_wait(file, sock, wait);
 	mask = 0;
+	shutdown = READ_ONCE(sk->sk_shutdown);
+	state = READ_ONCE(sk->sk_state);
 
 	/* exceptional events? */
-	if (sk->sk_err)
+	if (READ_ONCE(sk->sk_err))
 		mask |= EPOLLERR;
-	if (sk->sk_shutdown == SHUTDOWN_MASK)
+	if (shutdown == SHUTDOWN_MASK)
 		mask |= EPOLLHUP;
-	if (sk->sk_shutdown & RCV_SHUTDOWN)
+	if (shutdown & RCV_SHUTDOWN)
 		mask |= EPOLLRDHUP | EPOLLIN | EPOLLRDNORM;
 
 	/* readable? */
@@ -3054,17 +3071,21 @@
 		mask |= EPOLLIN | EPOLLRDNORM;
 	if (sk_is_readable(sk))
 		mask |= EPOLLIN | EPOLLRDNORM;
+#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
+	if (READ_ONCE(unix_sk(sk)->oob_skb))
+		mask |= EPOLLPRI;
+#endif
 
 	/* Connection-based need to check for termination and startup */
 	if ((sk->sk_type == SOCK_STREAM || sk->sk_type == SOCK_SEQPACKET) &&
-	    sk->sk_state == TCP_CLOSE)
+	    state == TCP_CLOSE)
 		mask |= EPOLLHUP;
 
 	/*
 	 * we set writable also when the other side has shut down the
 	 * connection. This prevents stuck sockets.
 	 */
-	if (unix_writable(sk))
+	if (unix_writable(sk, state))
 		mask |= EPOLLOUT | EPOLLWRNORM | EPOLLWRBAND;
 
 	return mask;
@@ -3075,19 +3096,24 @@
 {
 	struct sock *sk = sock->sk, *other;
 	unsigned int writable;
+	unsigned char state;
 	__poll_t mask;
+	u8 shutdown;
 
 	sock_poll_wait(file, sock, wait);
 	mask = 0;
+	shutdown = READ_ONCE(sk->sk_shutdown);
+	state = READ_ONCE(sk->sk_state);
 
 	/* exceptional events? */
-	if (sk->sk_err || !skb_queue_empty_lockless(&sk->sk_error_queue))
+	if (READ_ONCE(sk->sk_err) ||
+	    !skb_queue_empty_lockless(&sk->sk_error_queue))
 		mask |= EPOLLERR |
 			(sock_flag(sk, SOCK_SELECT_ERR_QUEUE) ? EPOLLPRI : 0);
 
-	if (sk->sk_shutdown & RCV_SHUTDOWN)
+	if (shutdown & RCV_SHUTDOWN)
 		mask |= EPOLLRDHUP | EPOLLIN | EPOLLRDNORM;
-	if (sk->sk_shutdown == SHUTDOWN_MASK)
+	if (shutdown == SHUTDOWN_MASK)
 		mask |= EPOLLHUP;
 
 	/* readable? */
@@ -3097,19 +3123,14 @@
 		mask |= EPOLLIN | EPOLLRDNORM;
 
 	/* Connection-based need to check for termination and startup */
-	if (sk->sk_type == SOCK_SEQPACKET) {
-		if (sk->sk_state == TCP_CLOSE)
-			mask |= EPOLLHUP;
-		/* connection hasn't started yet? */
-		if (sk->sk_state == TCP_SYN_SENT)
-			return mask;
-	}
+	if (sk->sk_type == SOCK_SEQPACKET && state == TCP_CLOSE)
+		mask |= EPOLLHUP;
 
 	/* No write status requested, avoid expensive OUT tests. */
 	if (!(poll_requested_events(wait) & (EPOLLWRBAND|EPOLLWRNORM|EPOLLOUT)))
 		return mask;
 
-	writable = unix_writable(sk);
+	writable = unix_writable(sk, state);
 	if (writable) {
 		unix_state_lock(sk);
 
@@ -3401,6 +3422,7 @@
 	rc = proto_register(&unix_stream_proto, 1);
 	if (rc != 0) {
 		pr_crit("%s: Cannot create unix_sock SLAB cache!\n", __func__);
+		proto_unregister(&unix_dgram_proto);
 		goto out;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/unix/diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/unix/diag.c
@@ -64,7 +64,7 @@
 	u32 *buf;
 	int i;
 
-	if (sk->sk_state == TCP_LISTEN) {
+	if (READ_ONCE(sk->sk_state) == TCP_LISTEN) {
 		spin_lock(&sk->sk_receive_queue.lock);
 
 		attr = nla_reserve(nlskb, UNIX_DIAG_ICONS,
@@ -83,7 +83,7 @@
 			 * queue lock. With the other's queue locked it's
 			 * OK to lock the state.
 			 */
-			unix_state_lock_nested(req);
+			unix_state_lock_nested(req, U_LOCK_DIAG);
 			peer = unix_sk(req)->peer;
 			buf[i++] = (peer ? sock_i_ino(peer) : 0);
 			unix_state_unlock(req);
@@ -102,8 +102,8 @@
 {
 	struct unix_diag_rqlen rql;
 
-	if (sk->sk_state == TCP_LISTEN) {
-		rql.udiag_rqueue = sk->sk_receive_queue.qlen;
+	if (READ_ONCE(sk->sk_state) == TCP_LISTEN) {
+		rql.udiag_rqueue = skb_queue_len_lockless(&sk->sk_receive_queue);
 		rql.udiag_wqueue = sk->sk_max_ack_backlog;
 	} else {
 		rql.udiag_rqueue = (u32) unix_inq_len(sk);
@@ -113,14 +113,16 @@
 	return nla_put(nlskb, UNIX_DIAG_RQLEN, sizeof(rql), &rql);
 }
 
-static int sk_diag_dump_uid(struct sock *sk, struct sk_buff *nlskb)
+static int sk_diag_dump_uid(struct sock *sk, struct sk_buff *nlskb,
+			    struct user_namespace *user_ns)
 {
-	uid_t uid = from_kuid_munged(sk_user_ns(nlskb->sk), sock_i_uid(sk));
+	uid_t uid = from_kuid_munged(user_ns, sock_i_uid(sk));
 	return nla_put(nlskb, UNIX_DIAG_UID, sizeof(uid_t), &uid);
 }
 
 static int sk_diag_fill(struct sock *sk, struct sk_buff *skb, struct unix_diag_req *req,
-		u32 portid, u32 seq, u32 flags, int sk_ino)
+			struct user_namespace *user_ns,
+			u32 portid, u32 seq, u32 flags, int sk_ino)
 {
 	struct nlmsghdr *nlh;
 	struct unix_diag_msg *rep;
@@ -133,7 +135,7 @@
 	rep = nlmsg_data(nlh);
 	rep->udiag_family = AF_UNIX;
 	rep->udiag_type = sk->sk_type;
-	rep->udiag_state = sk->sk_state;
+	rep->udiag_state = READ_ONCE(sk->sk_state);
 	rep->pad = 0;
 	rep->udiag_ino = sk_ino;
 	sock_diag_save_cookie(sk, rep->udiag_cookie);
@@ -162,11 +164,11 @@
 	    sock_diag_put_meminfo(sk, skb, UNIX_DIAG_MEMINFO))
 		goto out_nlmsg_trim;
 
-	if (nla_put_u8(skb, UNIX_DIAG_SHUTDOWN, sk->sk_shutdown))
+	if (nla_put_u8(skb, UNIX_DIAG_SHUTDOWN, READ_ONCE(sk->sk_shutdown)))
 		goto out_nlmsg_trim;
 
 	if ((req->udiag_show & UDIAG_SHOW_UID) &&
-	    sk_diag_dump_uid(sk, skb))
+	    sk_diag_dump_uid(sk, skb, user_ns))
 		goto out_nlmsg_trim;
 
 	nlmsg_end(skb, nlh);
@@ -178,7 +180,8 @@
 }
 
 static int sk_diag_dump(struct sock *sk, struct sk_buff *skb, struct unix_diag_req *req,
-		u32 portid, u32 seq, u32 flags)
+			struct user_namespace *user_ns,
+			u32 portid, u32 seq, u32 flags)
 {
 	int sk_ino;
 
@@ -189,7 +192,7 @@
 	if (!sk_ino)
 		return 0;
 
-	return sk_diag_fill(sk, skb, req, portid, seq, flags, sk_ino);
+	return sk_diag_fill(sk, skb, req, user_ns, portid, seq, flags, sk_ino);
 }
 
 static int unix_diag_dump(struct sk_buff *skb, struct netlink_callback *cb)
@@ -215,9 +218,9 @@
 				continue;
 			if (num < s_num)
 				goto next;
-			if (!(req->udiag_states & (1 << sk->sk_state)))
+			if (!(req->udiag_states & (1 << READ_ONCE(sk->sk_state))))
 				goto next;
-			if (sk_diag_dump(sk, skb, req,
+			if (sk_diag_dump(sk, skb, req, sk_user_ns(skb->sk),
 					 NETLINK_CB(cb->skb).portid,
 					 cb->nlh->nlmsg_seq,
 					 NLM_F_MULTI) < 0)
@@ -285,7 +288,8 @@
 	if (!rep)
 		goto out;
 
-	err = sk_diag_fill(sk, rep, req, NETLINK_CB(in_skb).portid,
+	err = sk_diag_fill(sk, rep, req, sk_user_ns(NETLINK_CB(in_skb).sk),
+			   NETLINK_CB(in_skb).portid,
 			   nlh->nlmsg_seq, 0, req->udiag_ino);
 	if (err < 0) {
 		nlmsg_free(rep);
--- linux-xilinx-zynqmp-5.15.0.orig/net/unix/garbage.c
+++ linux-xilinx-zynqmp-5.15.0/net/unix/garbage.c
@@ -166,17 +166,18 @@
 
 static void dec_inflight(struct unix_sock *usk)
 {
-	atomic_long_dec(&usk->inflight);
+	usk->inflight--;
 }
 
 static void inc_inflight(struct unix_sock *usk)
 {
-	atomic_long_inc(&usk->inflight);
+	usk->inflight++;
 }
 
 static void inc_inflight_move_tail(struct unix_sock *u)
 {
-	atomic_long_inc(&u->inflight);
+	u->inflight++;
+
 	/* If this still might be part of a cycle, move it to the end
 	 * of the list, so that it's checked even if it was already
 	 * passed over
@@ -192,15 +193,19 @@
 {
 	/* If number of inflight sockets is insane,
 	 * force a garbage collect right now.
+	 * Paired with the WRITE_ONCE() in unix_inflight(),
+	 * unix_notinflight() and gc_in_progress().
 	 */
-	if (unix_tot_inflight > UNIX_INFLIGHT_TRIGGER_GC && !gc_in_progress)
+	if (READ_ONCE(unix_tot_inflight) > UNIX_INFLIGHT_TRIGGER_GC &&
+	    !READ_ONCE(gc_in_progress))
 		unix_gc();
-	wait_event(unix_gc_wait, gc_in_progress == false);
+	wait_event(unix_gc_wait, !READ_ONCE(gc_in_progress));
 }
 
 /* The external entry point: unix_gc() */
 void unix_gc(void)
 {
+	struct sk_buff *next_skb, *skb;
 	struct unix_sock *u;
 	struct unix_sock *next;
 	struct sk_buff_head hitlist;
@@ -213,7 +218,9 @@
 	if (gc_in_progress)
 		goto out;
 
-	gc_in_progress = true;
+	/* Paired with READ_ONCE() in wait_for_unix_gc(). */
+	WRITE_ONCE(gc_in_progress, true);
+
 	/* First, select candidates for garbage collection.  Only
 	 * in-flight sockets are considered, and from those only ones
 	 * which don't have any external reference.
@@ -228,20 +235,34 @@
 	 * receive queues.  Other, non candidate sockets _can_ be
 	 * added to queue, so we must make sure only to touch
 	 * candidates.
+	 *
+	 * Embryos, though never candidates themselves, affect which
+	 * candidates are reachable by the garbage collector.  Before
+	 * being added to a listener's queue, an embryo may already
+	 * receive data carrying SCM_RIGHTS, potentially making the
+	 * passed socket a candidate that is not yet reachable by the
+	 * collector.  It becomes reachable once the embryo is
+	 * enqueued.  Therefore, we must ensure that no SCM-laden
+	 * embryo appears in a (candidate) listener's queue between
+	 * consecutive scan_children() calls.
 	 */
 	list_for_each_entry_safe(u, next, &gc_inflight_list, link) {
+		struct sock *sk = &u->sk;
 		long total_refs;
-		long inflight_refs;
 
-		total_refs = file_count(u->sk.sk_socket->file);
-		inflight_refs = atomic_long_read(&u->inflight);
+		total_refs = file_count(sk->sk_socket->file);
 
-		BUG_ON(inflight_refs < 1);
-		BUG_ON(total_refs < inflight_refs);
-		if (total_refs == inflight_refs) {
+		BUG_ON(!u->inflight);
+		BUG_ON(total_refs < u->inflight);
+		if (total_refs == u->inflight) {
 			list_move_tail(&u->link, &gc_candidates);
 			__set_bit(UNIX_GC_CANDIDATE, &u->gc_flags);
 			__set_bit(UNIX_GC_MAYBE_CYCLE, &u->gc_flags);
+
+			if (sk->sk_state == TCP_LISTEN) {
+				unix_state_lock_nested(sk, U_LOCK_GC_LISTENER);
+				unix_state_unlock(sk);
+			}
 		}
 	}
 
@@ -265,7 +286,7 @@
 		/* Move cursor to after the current position. */
 		list_move(&cursor, &u->link);
 
-		if (atomic_long_read(&u->inflight) > 0) {
+		if (u->inflight) {
 			list_move_tail(&u->link, &not_cycle_list);
 			__clear_bit(UNIX_GC_MAYBE_CYCLE, &u->gc_flags);
 			scan_children(&u->sk, inc_inflight_move_tail, NULL);
@@ -278,9 +299,17 @@
 	 * which are creating the cycle(s).
 	 */
 	skb_queue_head_init(&hitlist);
-	list_for_each_entry(u, &gc_candidates, link)
+	list_for_each_entry(u, &gc_candidates, link) {
 		scan_children(&u->sk, inc_inflight, &hitlist);
 
+#if IS_ENABLED(CONFIG_AF_UNIX_OOB)
+		if (u->oob_skb) {
+			kfree_skb(u->oob_skb);
+			u->oob_skb = NULL;
+		}
+#endif
+	}
+
 	/* not_cycle_list contains those sockets which do not make up a
 	 * cycle.  Restore these to the inflight list.
 	 */
@@ -292,14 +321,36 @@
 
 	spin_unlock(&unix_gc_lock);
 
+	/* We need io_uring to clean its registered files, ignore all io_uring
+	 * originated skbs. It's fine as io_uring doesn't keep references to
+	 * other io_uring instances and so killing all other files in the cycle
+	 * will put all io_uring references forcing it to go through normal
+	 * release.path eventually putting registered files.
+	 */
+	skb_queue_walk_safe(&hitlist, skb, next_skb) {
+		if (skb->scm_io_uring) {
+			__skb_unlink(skb, &hitlist);
+			skb_queue_tail(&skb->sk->sk_receive_queue, skb);
+		}
+	}
+
 	/* Here we are. Hitlist is filled. Die. */
 	__skb_queue_purge(&hitlist);
 
 	spin_lock(&unix_gc_lock);
 
+	/* There could be io_uring registered files, just push them back to
+	 * the inflight list
+	 */
+	list_for_each_entry_safe(u, next, &gc_candidates, link)
+		list_move_tail(&u->link, &gc_inflight_list);
+
 	/* All candidates should have been detached by now. */
 	BUG_ON(!list_empty(&gc_candidates));
-	gc_in_progress = false;
+
+	/* Paired with READ_ONCE() in wait_for_unix_gc(). */
+	WRITE_ONCE(gc_in_progress, false);
+
 	wake_up(&unix_gc_wait);
 
  out:
--- linux-xilinx-zynqmp-5.15.0.orig/net/unix/scm.c
+++ linux-xilinx-zynqmp-5.15.0/net/unix/scm.c
@@ -34,10 +34,8 @@
 		/* PF_UNIX ? */
 		if (s && sock->ops && sock->ops->family == PF_UNIX)
 			u_sock = s;
-	} else {
-		/* Could be an io_uring instance */
-		u_sock = io_uring_get_socket(filp);
 	}
+
 	return u_sock;
 }
 EXPORT_SYMBOL(unix_get_socket);
@@ -54,15 +52,17 @@
 	if (s) {
 		struct unix_sock *u = unix_sk(s);
 
-		if (atomic_long_inc_return(&u->inflight) == 1) {
+		if (!u->inflight) {
 			BUG_ON(!list_empty(&u->link));
 			list_add_tail(&u->link, &gc_inflight_list);
 		} else {
 			BUG_ON(list_empty(&u->link));
 		}
-		unix_tot_inflight++;
+		u->inflight++;
+		/* Paired with READ_ONCE() in wait_for_unix_gc() */
+		WRITE_ONCE(unix_tot_inflight, unix_tot_inflight + 1);
 	}
-	user->unix_inflight++;
+	WRITE_ONCE(user->unix_inflight, user->unix_inflight + 1);
 	spin_unlock(&unix_gc_lock);
 }
 
@@ -75,14 +75,16 @@
 	if (s) {
 		struct unix_sock *u = unix_sk(s);
 
-		BUG_ON(!atomic_long_read(&u->inflight));
+		BUG_ON(!u->inflight);
 		BUG_ON(list_empty(&u->link));
 
-		if (atomic_long_dec_and_test(&u->inflight))
+		u->inflight--;
+		if (!u->inflight)
 			list_del_init(&u->link);
-		unix_tot_inflight--;
+		/* Paired with READ_ONCE() in wait_for_unix_gc() */
+		WRITE_ONCE(unix_tot_inflight, unix_tot_inflight - 1);
 	}
-	user->unix_inflight--;
+	WRITE_ONCE(user->unix_inflight, user->unix_inflight - 1);
 	spin_unlock(&unix_gc_lock);
 }
 
@@ -96,7 +98,7 @@
 {
 	struct user_struct *user = current_user();
 
-	if (unlikely(user->unix_inflight > task_rlimit(p, RLIMIT_NOFILE)))
+	if (unlikely(READ_ONCE(user->unix_inflight) > task_rlimit(p, RLIMIT_NOFILE)))
 		return !capable(CAP_SYS_RESOURCE) && !capable(CAP_SYS_ADMIN);
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/unix/unix_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/net/unix/unix_bpf.c
@@ -55,6 +55,9 @@
 	struct sk_psock *psock;
 	int copied;
 
+	if (!len)
+		return 0;
+
 	psock = sk_psock_get(sk);
 	if (unlikely(!psock))
 		return __unix_recvmsg(sk, msg, len, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/net/vmw_vsock/af_vsock.c
+++ linux-xilinx-zynqmp-5.15.0/net/vmw_vsock/af_vsock.c
@@ -113,12 +113,14 @@
 static int __vsock_bind(struct sock *sk, struct sockaddr_vm *addr);
 static void vsock_sk_destruct(struct sock *sk);
 static int vsock_queue_rcv_skb(struct sock *sk, struct sk_buff *skb);
+static void vsock_close(struct sock *sk, long timeout);
 
 /* Protocol family. */
 static struct proto vsock_proto = {
 	.name = "AF_VSOCK",
 	.owner = THIS_MODULE,
 	.obj_size = sizeof(struct vsock_sock),
+	.close = vsock_close,
 };
 
 /* The default peer timeout indicates how long we will wait for a peer response
@@ -328,12 +330,16 @@
 
 void vsock_remove_sock(struct vsock_sock *vsk)
 {
-	vsock_remove_bound(vsk);
+	/* Transport reassignment must not remove the binding. */
+	if (sock_flag(sk_vsock(vsk), SOCK_DEAD))
+		vsock_remove_bound(vsk);
+
 	vsock_remove_connected(vsk);
 }
 EXPORT_SYMBOL_GPL(vsock_remove_sock);
 
-void vsock_for_each_connected_socket(void (*fn)(struct sock *sk))
+void vsock_for_each_connected_socket(struct vsock_transport *transport,
+				     void (*fn)(struct sock *sk))
 {
 	int i;
 
@@ -342,8 +348,12 @@
 	for (i = 0; i < ARRAY_SIZE(vsock_connected_table); i++) {
 		struct vsock_sock *vsk;
 		list_for_each_entry(vsk, &vsock_connected_table[i],
-				    connected_table)
+				    connected_table) {
+			if (vsk->transport != transport)
+				continue;
+
 			fn(sk_vsock(vsk));
+		}
 	}
 
 	spin_unlock_bh(&vsock_table_lock);
@@ -477,6 +487,15 @@
 		 */
 		vsk->transport->release(vsk);
 		vsock_deassign_transport(vsk);
+
+		/* transport's release() and destruct() can touch some socket
+		 * state, since we are reassigning the socket to a new transport
+		 * during vsock_connect(), let's reset these fields to have a
+		 * clean state.
+		 */
+		sock_reset_flag(sk, SOCK_DONE);
+		sk->sk_state = TCP_CLOSE;
+		vsk->peer_shutdown = 0;
 	}
 
 	/* We increase the module refcnt to prevent the transport unloading
@@ -786,39 +805,44 @@
 
 static void __vsock_release(struct sock *sk, int level)
 {
-	if (sk) {
-		struct sock *pending;
-		struct vsock_sock *vsk;
+	struct vsock_sock *vsk;
+	struct sock *pending;
 
-		vsk = vsock_sk(sk);
-		pending = NULL;	/* Compiler warning. */
+	vsk = vsock_sk(sk);
+	pending = NULL;	/* Compiler warning. */
 
-		/* When "level" is SINGLE_DEPTH_NESTING, use the nested
-		 * version to avoid the warning "possible recursive locking
-		 * detected". When "level" is 0, lock_sock_nested(sk, level)
-		 * is the same as lock_sock(sk).
-		 */
-		lock_sock_nested(sk, level);
+	/* When "level" is SINGLE_DEPTH_NESTING, use the nested
+	 * version to avoid the warning "possible recursive locking
+	 * detected". When "level" is 0, lock_sock_nested(sk, level)
+	 * is the same as lock_sock(sk).
+	 */
+	lock_sock_nested(sk, level);
 
-		if (vsk->transport)
-			vsk->transport->release(vsk);
-		else if (sock_type_connectible(sk->sk_type))
-			vsock_remove_sock(vsk);
-
-		sock_orphan(sk);
-		sk->sk_shutdown = SHUTDOWN_MASK;
-
-		skb_queue_purge(&sk->sk_receive_queue);
-
-		/* Clean up any sockets that never were accepted. */
-		while ((pending = vsock_dequeue_accept(sk)) != NULL) {
-			__vsock_release(pending, SINGLE_DEPTH_NESTING);
-			sock_put(pending);
-		}
+	/* Indicate to vsock_remove_sock() that the socket is being released and
+	 * can be removed from the bound_table. Unlike transport reassignment
+	 * case, where the socket must remain bound despite vsock_remove_sock()
+	 * being called from the transport release() callback.
+	 */
+	sock_set_flag(sk, SOCK_DEAD);
 
-		release_sock(sk);
-		sock_put(sk);
+	if (vsk->transport)
+		vsk->transport->release(vsk);
+	else if (sock_type_connectible(sk->sk_type))
+		vsock_remove_sock(vsk);
+
+	sock_orphan(sk);
+	sk->sk_shutdown = SHUTDOWN_MASK;
+
+	skb_queue_purge(&sk->sk_receive_queue);
+
+	/* Clean up any sockets that never were accepted. */
+	while ((pending = vsock_dequeue_accept(sk)) != NULL) {
+		__vsock_release(pending, SINGLE_DEPTH_NESTING);
+		sock_put(pending);
 	}
+
+	release_sock(sk);
+	sock_put(sk);
 }
 
 static void vsock_sk_destruct(struct sock *sk)
@@ -856,6 +880,9 @@
 
 s64 vsock_stream_has_data(struct vsock_sock *vsk)
 {
+	if (WARN_ON(!vsk->transport))
+		return 0;
+
 	return vsk->transport->stream_has_data(vsk);
 }
 EXPORT_SYMBOL_GPL(vsock_stream_has_data);
@@ -864,6 +891,9 @@
 {
 	struct sock *sk = sk_vsock(vsk);
 
+	if (WARN_ON(!vsk->transport))
+		return 0;
+
 	if (sk->sk_type == SOCK_SEQPACKET)
 		return vsk->transport->seqpacket_has_data(vsk);
 	else
@@ -872,13 +902,29 @@
 
 s64 vsock_stream_has_space(struct vsock_sock *vsk)
 {
+	if (WARN_ON(!vsk->transport))
+		return 0;
+
 	return vsk->transport->stream_has_space(vsk);
 }
 EXPORT_SYMBOL_GPL(vsock_stream_has_space);
 
+/* Dummy callback required by sockmap.
+ * See unconditional call of saved_close() in sock_map_close().
+ */
+static void vsock_close(struct sock *sk, long timeout)
+{
+}
+
 static int vsock_release(struct socket *sock)
 {
-	__vsock_release(sock->sk, 0);
+	struct sock *sk = sock->sk;
+
+	if (!sk)
+		return 0;
+
+	sk->sk_prot->close(sk, 0);
+	__vsock_release(sk, 0);
 	sock->sk = NULL;
 	sock->state = SS_FREE;
 
@@ -1280,6 +1326,7 @@
 	if (sk->sk_state == TCP_SYN_SENT &&
 	    (sk->sk_shutdown != SHUTDOWN_MASK)) {
 		sk->sk_state = TCP_CLOSE;
+		sk->sk_socket->state = SS_UNCONNECTED;
 		sk->sk_err = ETIMEDOUT;
 		sk_error_report(sk);
 		vsock_transport_cancel_pkt(vsk);
@@ -1322,6 +1369,8 @@
 		 * non-blocking call.
 		 */
 		err = -EALREADY;
+		if (flags & O_NONBLOCK)
+			goto out;
 		break;
 	default:
 		if ((sk->sk_state == TCP_LISTEN) ||
@@ -1360,6 +1409,11 @@
 		if (err < 0)
 			goto out;
 
+		/* sk_err might have been set as a result of an earlier
+		 * (failed) connect attempt.
+		 */
+		sk->sk_err = 0;
+
 		/* Mark sock as connecting and set the error code to in
 		 * progress in case this is a non-blocking connect.
 		 */
@@ -1374,7 +1428,11 @@
 	timeout = vsk->connect_timeout;
 	prepare_to_wait(sk_sleep(sk), &wait, TASK_INTERRUPTIBLE);
 
-	while (sk->sk_state != TCP_ESTABLISHED && sk->sk_err == 0) {
+	/* If the socket is already closing or it is in an error state, there
+	 * is no point in waiting.
+	 */
+	while (sk->sk_state != TCP_ESTABLISHED &&
+	       sk->sk_state != TCP_CLOSING && sk->sk_err == 0) {
 		if (flags & O_NONBLOCK) {
 			/* If we're not going to block, we schedule a timeout
 			 * function to generate a timeout on the connection
@@ -1383,7 +1441,14 @@
 			 * timeout fires.
 			 */
 			sock_hold(sk);
-			schedule_delayed_work(&vsk->connect_work, timeout);
+
+			/* If the timeout function is already scheduled,
+			 * reschedule it, then ungrab the socket refcount to
+			 * keep it balanced.
+			 */
+			if (mod_delayed_work(system_wq, &vsk->connect_work,
+					     timeout))
+				sock_put(sk);
 
 			/* Skip ahead to preserve error code set above. */
 			goto out_wait;
@@ -1398,8 +1463,9 @@
 			sk->sk_state = sk->sk_state == TCP_ESTABLISHED ? TCP_CLOSING : TCP_CLOSE;
 			sock->state = SS_UNCONNECTED;
 			vsock_transport_cancel_pkt(vsk);
+			vsock_remove_connected(vsk);
 			goto out_wait;
-		} else if (timeout == 0) {
+		} else if ((sk->sk_state != TCP_ESTABLISHED) && (timeout == 0)) {
 			err = -ETIMEDOUT;
 			sk->sk_state = TCP_CLOSE;
 			sock->state = SS_UNCONNECTED;
@@ -1881,8 +1947,11 @@
 	err = 0;
 	transport = vsk->transport;
 
-	while ((data = vsock_connectible_has_data(vsk)) == 0) {
+	while (1) {
 		prepare_to_wait(sk_sleep(sk), wait, TASK_INTERRUPTIBLE);
+		data = vsock_connectible_has_data(vsk);
+		if (data != 0)
+			break;
 
 		if (sk->sk_err != 0 ||
 		    (sk->sk_shutdown & RCV_SHUTDOWN) ||
--- linux-xilinx-zynqmp-5.15.0.orig/net/vmw_vsock/hyperv_transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/vmw_vsock/hyperv_transport.c
@@ -538,6 +538,7 @@
 		vmbus_hvsock_device_unregister(chan);
 
 	kfree(hvs);
+	vsk->trans = NULL;
 }
 
 static int hvs_dgram_bind(struct vsock_sock *vsk, struct sockaddr_vm *addr)
--- linux-xilinx-zynqmp-5.15.0.orig/net/vmw_vsock/virtio_transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/vmw_vsock/virtio_transport.c
@@ -24,6 +24,7 @@
 static struct workqueue_struct *virtio_vsock_workqueue;
 static struct virtio_vsock __rcu *the_virtio_vsock;
 static DEFINE_MUTEX(the_virtio_vsock_mutex); /* protects the_virtio_vsock */
+static struct virtio_transport virtio_transport; /* forward declaration */
 
 struct virtio_vsock {
 	struct virtio_device *vdev;
@@ -384,7 +385,8 @@
 	switch (le32_to_cpu(event->id)) {
 	case VIRTIO_VSOCK_EVENT_TRANSPORT_RESET:
 		virtio_vsock_update_guest_cid(vsock);
-		vsock_for_each_connected_socket(virtio_vsock_reset_sock);
+		vsock_for_each_connected_socket(&virtio_transport.transport,
+						virtio_vsock_reset_sock);
 		break;
 	}
 }
@@ -564,62 +566,35 @@
 	mutex_unlock(&vsock->rx_lock);
 }
 
-static int virtio_vsock_probe(struct virtio_device *vdev)
+static int virtio_vsock_vqs_init(struct virtio_vsock *vsock)
 {
-	vq_callback_t *callbacks[] = {
-		virtio_vsock_rx_done,
-		virtio_vsock_tx_done,
-		virtio_vsock_event_done,
-	};
+	struct virtio_device *vdev = vsock->vdev;
 	static const char * const names[] = {
 		"rx",
 		"tx",
 		"event",
 	};
-	struct virtio_vsock *vsock = NULL;
+	vq_callback_t *callbacks[] = {
+		virtio_vsock_rx_done,
+		virtio_vsock_tx_done,
+		virtio_vsock_event_done,
+	};
 	int ret;
 
-	ret = mutex_lock_interruptible(&the_virtio_vsock_mutex);
-	if (ret)
-		return ret;
-
-	/* Only one virtio-vsock device per guest is supported */
-	if (rcu_dereference_protected(the_virtio_vsock,
-				lockdep_is_held(&the_virtio_vsock_mutex))) {
-		ret = -EBUSY;
-		goto out;
-	}
-
-	vsock = kzalloc(sizeof(*vsock), GFP_KERNEL);
-	if (!vsock) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	vsock->vdev = vdev;
-
-	ret = virtio_find_vqs(vsock->vdev, VSOCK_VQ_MAX,
-			      vsock->vqs, callbacks, names,
+	ret = virtio_find_vqs(vdev, VSOCK_VQ_MAX, vsock->vqs, callbacks, names,
 			      NULL);
 	if (ret < 0)
-		goto out;
+		return ret;
 
 	virtio_vsock_update_guest_cid(vsock);
 
-	vsock->rx_buf_nr = 0;
-	vsock->rx_buf_max_nr = 0;
-	atomic_set(&vsock->queued_replies, 0);
+	virtio_device_ready(vdev);
 
-	mutex_init(&vsock->tx_lock);
-	mutex_init(&vsock->rx_lock);
-	mutex_init(&vsock->event_lock);
-	spin_lock_init(&vsock->send_pkt_list_lock);
-	INIT_LIST_HEAD(&vsock->send_pkt_list);
-	INIT_WORK(&vsock->rx_work, virtio_transport_rx_work);
-	INIT_WORK(&vsock->tx_work, virtio_transport_tx_work);
-	INIT_WORK(&vsock->event_work, virtio_transport_event_work);
-	INIT_WORK(&vsock->send_pkt_work, virtio_transport_send_pkt_work);
+	return 0;
+}
 
+static void virtio_vsock_vqs_start(struct virtio_vsock *vsock)
+{
 	mutex_lock(&vsock->tx_lock);
 	vsock->tx_run = true;
 	mutex_unlock(&vsock->tx_lock);
@@ -634,35 +609,26 @@
 	vsock->event_run = true;
 	mutex_unlock(&vsock->event_lock);
 
-	if (virtio_has_feature(vdev, VIRTIO_VSOCK_F_SEQPACKET))
-		vsock->seqpacket_allow = true;
-
-	vdev->priv = vsock;
-	rcu_assign_pointer(the_virtio_vsock, vsock);
-
-	mutex_unlock(&the_virtio_vsock_mutex);
-
-	return 0;
-
-out:
-	kfree(vsock);
-	mutex_unlock(&the_virtio_vsock_mutex);
-	return ret;
+	/* virtio_transport_send_pkt() can queue packets once
+	 * the_virtio_vsock is set, but they won't be processed until
+	 * vsock->tx_run is set to true. We queue vsock->send_pkt_work
+	 * when initialization finishes to send those packets queued
+	 * earlier.
+	 * We don't need to queue the other workers (rx, event) because
+	 * as long as we don't fill the queues with empty buffers, the
+	 * host can't send us any notification.
+	 */
+	queue_work(virtio_vsock_workqueue, &vsock->send_pkt_work);
 }
 
-static void virtio_vsock_remove(struct virtio_device *vdev)
+static void virtio_vsock_vqs_del(struct virtio_vsock *vsock)
 {
-	struct virtio_vsock *vsock = vdev->priv;
+	struct virtio_device *vdev = vsock->vdev;
 	struct virtio_vsock_pkt *pkt;
 
-	mutex_lock(&the_virtio_vsock_mutex);
-
-	vdev->priv = NULL;
-	rcu_assign_pointer(the_virtio_vsock, NULL);
-	synchronize_rcu();
-
-	/* Reset all connected sockets when the device disappear */
-	vsock_for_each_connected_socket(virtio_vsock_reset_sock);
+	/* Reset all connected sockets when the VQs disappear */
+	vsock_for_each_connected_socket(&virtio_transport.transport,
+					virtio_vsock_reset_sock);
 
 	/* Stop all work handlers to make sure no one is accessing the device,
 	 * so we can safely call vdev->config->reset().
@@ -705,6 +671,79 @@
 
 	/* Delete virtqueues and flush outstanding callbacks if any */
 	vdev->config->del_vqs(vdev);
+}
+
+static int virtio_vsock_probe(struct virtio_device *vdev)
+{
+	struct virtio_vsock *vsock = NULL;
+	int ret;
+
+	ret = mutex_lock_interruptible(&the_virtio_vsock_mutex);
+	if (ret)
+		return ret;
+
+	/* Only one virtio-vsock device per guest is supported */
+	if (rcu_dereference_protected(the_virtio_vsock,
+				lockdep_is_held(&the_virtio_vsock_mutex))) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	vsock = kzalloc(sizeof(*vsock), GFP_KERNEL);
+	if (!vsock) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	vsock->vdev = vdev;
+
+	vsock->rx_buf_nr = 0;
+	vsock->rx_buf_max_nr = 0;
+	atomic_set(&vsock->queued_replies, 0);
+
+	mutex_init(&vsock->tx_lock);
+	mutex_init(&vsock->rx_lock);
+	mutex_init(&vsock->event_lock);
+	spin_lock_init(&vsock->send_pkt_list_lock);
+	INIT_LIST_HEAD(&vsock->send_pkt_list);
+	INIT_WORK(&vsock->rx_work, virtio_transport_rx_work);
+	INIT_WORK(&vsock->tx_work, virtio_transport_tx_work);
+	INIT_WORK(&vsock->event_work, virtio_transport_event_work);
+	INIT_WORK(&vsock->send_pkt_work, virtio_transport_send_pkt_work);
+
+	if (virtio_has_feature(vdev, VIRTIO_VSOCK_F_SEQPACKET))
+		vsock->seqpacket_allow = true;
+
+	vdev->priv = vsock;
+
+	ret = virtio_vsock_vqs_init(vsock);
+	if (ret < 0)
+		goto out;
+
+	rcu_assign_pointer(the_virtio_vsock, vsock);
+	virtio_vsock_vqs_start(vsock);
+
+	mutex_unlock(&the_virtio_vsock_mutex);
+
+	return 0;
+
+out:
+	kfree(vsock);
+	mutex_unlock(&the_virtio_vsock_mutex);
+	return ret;
+}
+
+static void virtio_vsock_remove(struct virtio_device *vdev)
+{
+	struct virtio_vsock *vsock = vdev->priv;
+
+	mutex_lock(&the_virtio_vsock_mutex);
+
+	vdev->priv = NULL;
+	rcu_assign_pointer(the_virtio_vsock, NULL);
+	synchronize_rcu();
+
+	virtio_vsock_vqs_del(vsock);
 
 	/* Other works can be queued before 'config->del_vqs()', so we flush
 	 * all works before to free the vsock object to avoid use after free.
@@ -719,6 +758,50 @@
 	kfree(vsock);
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int virtio_vsock_freeze(struct virtio_device *vdev)
+{
+	struct virtio_vsock *vsock = vdev->priv;
+
+	mutex_lock(&the_virtio_vsock_mutex);
+
+	rcu_assign_pointer(the_virtio_vsock, NULL);
+	synchronize_rcu();
+
+	virtio_vsock_vqs_del(vsock);
+
+	mutex_unlock(&the_virtio_vsock_mutex);
+
+	return 0;
+}
+
+static int virtio_vsock_restore(struct virtio_device *vdev)
+{
+	struct virtio_vsock *vsock = vdev->priv;
+	int ret;
+
+	mutex_lock(&the_virtio_vsock_mutex);
+
+	/* Only one virtio-vsock device per guest is supported */
+	if (rcu_dereference_protected(the_virtio_vsock,
+				lockdep_is_held(&the_virtio_vsock_mutex))) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	ret = virtio_vsock_vqs_init(vsock);
+	if (ret < 0)
+		goto out;
+
+	rcu_assign_pointer(the_virtio_vsock, vsock);
+	virtio_vsock_vqs_start(vsock);
+
+out:
+	mutex_unlock(&the_virtio_vsock_mutex);
+	return ret;
+}
+#endif /* CONFIG_PM_SLEEP */
+
 static struct virtio_device_id id_table[] = {
 	{ VIRTIO_ID_VSOCK, VIRTIO_DEV_ANY_ID },
 	{ 0 },
@@ -736,6 +819,10 @@
 	.id_table = id_table,
 	.probe = virtio_vsock_probe,
 	.remove = virtio_vsock_remove,
+#ifdef CONFIG_PM_SLEEP
+	.freeze = virtio_vsock_freeze,
+	.restore = virtio_vsock_restore,
+#endif
 };
 
 static int __init virtio_vsock_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/vmw_vsock/virtio_transport_common.c
+++ linux-xilinx-zynqmp-5.15.0/net/vmw_vsock/virtio_transport_common.c
@@ -26,6 +26,9 @@
 /* Threshold for detecting small packets to copy */
 #define GOOD_COPY_LEN  128
 
+static void virtio_transport_cancel_close_work(struct vsock_sock *vsk,
+					       bool cancel_timeout);
+
 static const struct virtio_transport *
 virtio_transport_get_ops(struct vsock_sock *vsk)
 {
@@ -355,6 +358,8 @@
 	struct virtio_vsock_pkt *pkt;
 	size_t bytes, total = 0;
 	u32 free_space;
+	u32 fwd_cnt_delta;
+	bool low_rx_bytes;
 	int err = -EFAULT;
 
 	spin_lock_bh(&vvs->rx_lock);
@@ -386,7 +391,10 @@
 		}
 	}
 
-	free_space = vvs->buf_alloc - (vvs->fwd_cnt - vvs->last_fwd_cnt);
+	fwd_cnt_delta = vvs->fwd_cnt - vvs->last_fwd_cnt;
+	free_space = vvs->buf_alloc - fwd_cnt_delta;
+	low_rx_bytes = (vvs->rx_bytes <
+			sock_rcvlowat(sk_vsock(vsk), 0, INT_MAX));
 
 	spin_unlock_bh(&vvs->rx_lock);
 
@@ -396,9 +404,11 @@
 	 * too high causes extra messages. Too low causes transmitter
 	 * stalls. As stalls are in theory more expensive than extra
 	 * messages, we set the limit to a high value. TODO: experiment
-	 * with different values.
+	 * with different values. Also send credit update message when
+	 * number of bytes in rx queue is not enough to wake up reader.
 	 */
-	if (free_space < VIRTIO_VSOCK_MAX_PKT_BUF_SIZE)
+	if (fwd_cnt_delta &&
+	    (free_space < VIRTIO_VSOCK_MAX_PKT_BUF_SIZE || low_rx_bytes))
 		virtio_transport_send_credit_update(vsk);
 
 	return total;
@@ -565,7 +575,7 @@
 	struct virtio_vsock_sock *vvs = vsk->trans;
 	s64 bytes;
 
-	bytes = vvs->peer_buf_alloc - (vvs->tx_cnt - vvs->peer_fwd_cnt);
+	bytes = (s64)vvs->peer_buf_alloc - (vvs->tx_cnt - vvs->peer_fwd_cnt);
 	if (bytes < 0)
 		bytes = 0;
 
@@ -804,7 +814,10 @@
 {
 	struct virtio_vsock_sock *vvs = vsk->trans;
 
+	virtio_transport_cancel_close_work(vsk, true);
+
 	kfree(vvs);
+	vsk->trans = NULL;
 }
 EXPORT_SYMBOL_GPL(virtio_transport_destruct);
 
@@ -891,17 +904,11 @@
 	}
 }
 
-static void virtio_transport_do_close(struct vsock_sock *vsk,
-				      bool cancel_timeout)
+static void virtio_transport_cancel_close_work(struct vsock_sock *vsk,
+					       bool cancel_timeout)
 {
 	struct sock *sk = sk_vsock(vsk);
 
-	sock_set_flag(sk, SOCK_DONE);
-	vsk->peer_shutdown = SHUTDOWN_MASK;
-	if (vsock_stream_has_data(vsk) <= 0)
-		sk->sk_state = TCP_CLOSING;
-	sk->sk_state_change(sk);
-
 	if (vsk->close_work_scheduled &&
 	    (!cancel_timeout || cancel_delayed_work(&vsk->close_work))) {
 		vsk->close_work_scheduled = false;
@@ -913,6 +920,20 @@
 	}
 }
 
+static void virtio_transport_do_close(struct vsock_sock *vsk,
+				      bool cancel_timeout)
+{
+	struct sock *sk = sk_vsock(vsk);
+
+	sock_set_flag(sk, SOCK_DONE);
+	vsk->peer_shutdown = SHUTDOWN_MASK;
+	if (vsock_stream_has_data(vsk) <= 0)
+		sk->sk_state = TCP_CLOSING;
+	sk->sk_state_change(sk);
+
+	virtio_transport_cancel_close_work(vsk, cancel_timeout);
+}
+
 static void virtio_transport_close_timeout(struct work_struct *work)
 {
 	struct vsock_sock *vsk =
@@ -1188,6 +1209,14 @@
 		return -ENOMEM;
 	}
 
+	/* __vsock_release() might have already flushed accept_queue.
+	 * Subsequent enqueues would lead to a memory leak.
+	 */
+	if (sk->sk_shutdown == SHUTDOWN_MASK) {
+		virtio_transport_reset_no_sock(t, pkt);
+		return -ESHUTDOWN;
+	}
+
 	child = vsock_create_connected(sk);
 	if (!child) {
 		virtio_transport_reset_no_sock(t, pkt);
@@ -1288,8 +1317,11 @@
 
 	lock_sock(sk);
 
-	/* Check if sk has been closed before lock_sock */
-	if (sock_flag(sk, SOCK_DONE)) {
+	/* Check if sk has been closed or assigned to another transport before
+	 * lock_sock (note: listener sockets are not assigned to any transport)
+	 */
+	if (sock_flag(sk, SOCK_DONE) ||
+	    (sk->sk_state != TCP_LISTEN && vsk->transport != &t->transport)) {
 		(void)virtio_transport_reset_no_sock(t, pkt);
 		release_sock(sk);
 		sock_put(sk);
@@ -1299,7 +1331,8 @@
 	space_available = virtio_transport_space_update(sk, pkt);
 
 	/* Update CID in case it has changed after a transport reset event */
-	vsk->local_addr.svm_cid = dst.svm_cid;
+	if (vsk->local_addr.svm_cid != VMADDR_CID_ANY)
+		vsk->local_addr.svm_cid = dst.svm_cid;
 
 	if (space_available)
 		sk->sk_write_space(sk);
@@ -1341,7 +1374,7 @@
 
 void virtio_transport_free_pkt(struct virtio_vsock_pkt *pkt)
 {
-	kfree(pkt->buf);
+	kvfree(pkt->buf);
 	kfree(pkt);
 }
 EXPORT_SYMBOL_GPL(virtio_transport_free_pkt);
--- linux-xilinx-zynqmp-5.15.0.orig/net/vmw_vsock/vmci_transport.c
+++ linux-xilinx-zynqmp-5.15.0/net/vmw_vsock/vmci_transport.c
@@ -75,6 +75,8 @@
 
 static int PROTOCOL_OVERRIDE = -1;
 
+static struct vsock_transport vmci_transport; /* forward declaration */
+
 /* Helper function to convert from a VMCI error code to a VSock error code. */
 
 static s32 vmci_transport_error_to_vsock_error(s32 vmci_error)
@@ -882,7 +884,8 @@
 					 const struct vmci_event_data *e_data,
 					 void *client_data)
 {
-	vsock_for_each_connected_socket(vmci_transport_handle_detach);
+	vsock_for_each_connected_socket(&vmci_transport,
+					vmci_transport_handle_detach);
 }
 
 static void vmci_transport_recv_pkt_work(struct work_struct *work)
@@ -1708,7 +1711,11 @@
 	if (!dg)
 		return -ENOMEM;
 
-	memcpy_from_msg(VMCI_DG_PAYLOAD(dg), msg, len);
+	err = memcpy_from_msg(VMCI_DG_PAYLOAD(dg), msg, len);
+	if (err) {
+		kfree(dg);
+		return err;
+	}
 
 	dg->dst = vmci_make_handle(remote_addr->svm_cid,
 				   remote_addr->svm_port);
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/certs/wens.hex
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/certs/wens.hex
@@ -0,0 +1,87 @@
+/* Chen-Yu Tsai's regdb certificate */
+0x30, 0x82, 0x02, 0xa7, 0x30, 0x82, 0x01, 0x8f,
+0x02, 0x14, 0x61, 0xc0, 0x38, 0x65, 0x1a, 0xab,
+0xdc, 0xf9, 0x4b, 0xd0, 0xac, 0x7f, 0xf0, 0x6c,
+0x72, 0x48, 0xdb, 0x18, 0xc6, 0x00, 0x30, 0x0d,
+0x06, 0x09, 0x2a, 0x86, 0x48, 0x86, 0xf7, 0x0d,
+0x01, 0x01, 0x0b, 0x05, 0x00, 0x30, 0x0f, 0x31,
+0x0d, 0x30, 0x0b, 0x06, 0x03, 0x55, 0x04, 0x03,
+0x0c, 0x04, 0x77, 0x65, 0x6e, 0x73, 0x30, 0x20,
+0x17, 0x0d, 0x32, 0x33, 0x31, 0x32, 0x30, 0x31,
+0x30, 0x37, 0x34, 0x31, 0x31, 0x34, 0x5a, 0x18,
+0x0f, 0x32, 0x31, 0x32, 0x33, 0x31, 0x31, 0x30,
+0x37, 0x30, 0x37, 0x34, 0x31, 0x31, 0x34, 0x5a,
+0x30, 0x0f, 0x31, 0x0d, 0x30, 0x0b, 0x06, 0x03,
+0x55, 0x04, 0x03, 0x0c, 0x04, 0x77, 0x65, 0x6e,
+0x73, 0x30, 0x82, 0x01, 0x22, 0x30, 0x0d, 0x06,
+0x09, 0x2a, 0x86, 0x48, 0x86, 0xf7, 0x0d, 0x01,
+0x01, 0x01, 0x05, 0x00, 0x03, 0x82, 0x01, 0x0f,
+0x00, 0x30, 0x82, 0x01, 0x0a, 0x02, 0x82, 0x01,
+0x01, 0x00, 0xa9, 0x7a, 0x2c, 0x78, 0x4d, 0xa7,
+0x19, 0x2d, 0x32, 0x52, 0xa0, 0x2e, 0x6c, 0xef,
+0x88, 0x7f, 0x15, 0xc5, 0xb6, 0x69, 0x54, 0x16,
+0x43, 0x14, 0x79, 0x53, 0xb7, 0xae, 0x88, 0xfe,
+0xc0, 0xb7, 0x5d, 0x47, 0x8e, 0x1a, 0xe1, 0xef,
+0xb3, 0x90, 0x86, 0xda, 0xd3, 0x64, 0x81, 0x1f,
+0xce, 0x5d, 0x9e, 0x4b, 0x6e, 0x58, 0x02, 0x3e,
+0xb2, 0x6f, 0x5e, 0x42, 0x47, 0x41, 0xf4, 0x2c,
+0xb8, 0xa8, 0xd4, 0xaa, 0xc0, 0x0e, 0xe6, 0x48,
+0xf0, 0xa8, 0xce, 0xcb, 0x08, 0xae, 0x37, 0xaf,
+0xf6, 0x40, 0x39, 0xcb, 0x55, 0x6f, 0x5b, 0x4f,
+0x85, 0x34, 0xe6, 0x69, 0x10, 0x50, 0x72, 0x5e,
+0x4e, 0x9d, 0x4c, 0xba, 0x38, 0x36, 0x0d, 0xce,
+0x73, 0x38, 0xd7, 0x27, 0x02, 0x2a, 0x79, 0x03,
+0xe1, 0xac, 0xcf, 0xb0, 0x27, 0x85, 0x86, 0x93,
+0x17, 0xab, 0xec, 0x42, 0x77, 0x37, 0x65, 0x8a,
+0x44, 0xcb, 0xd6, 0x42, 0x93, 0x92, 0x13, 0xe3,
+0x39, 0x45, 0xc5, 0x6e, 0x00, 0x4a, 0x7f, 0xcb,
+0x42, 0x17, 0x2b, 0x25, 0x8c, 0xb8, 0x17, 0x3b,
+0x15, 0x36, 0x59, 0xde, 0x42, 0xce, 0x21, 0xe6,
+0xb6, 0xc7, 0x6e, 0x5e, 0x26, 0x1f, 0xf7, 0x8a,
+0x57, 0x9e, 0xa5, 0x96, 0x72, 0xb7, 0x02, 0x32,
+0xeb, 0x07, 0x2b, 0x73, 0xe2, 0x4f, 0x66, 0x58,
+0x9a, 0xeb, 0x0f, 0x07, 0xb6, 0xab, 0x50, 0x8b,
+0xc3, 0x8f, 0x17, 0xfa, 0x0a, 0x99, 0xc2, 0x16,
+0x25, 0xbf, 0x2d, 0x6b, 0x1a, 0xaa, 0xe6, 0x3e,
+0x5f, 0xeb, 0x6d, 0x9b, 0x5d, 0x4d, 0x42, 0x83,
+0x2d, 0x39, 0xb8, 0xc9, 0xac, 0xdb, 0x3a, 0x91,
+0x50, 0xdf, 0xbb, 0xb1, 0x76, 0x6d, 0x15, 0x73,
+0xfd, 0xc6, 0xe6, 0x6b, 0x71, 0x9e, 0x67, 0x36,
+0x22, 0x83, 0x79, 0xb1, 0xd6, 0xb8, 0x84, 0x52,
+0xaf, 0x96, 0x5b, 0xc3, 0x63, 0x02, 0x4e, 0x78,
+0x70, 0x57, 0x02, 0x03, 0x01, 0x00, 0x01, 0x30,
+0x0d, 0x06, 0x09, 0x2a, 0x86, 0x48, 0x86, 0xf7,
+0x0d, 0x01, 0x01, 0x0b, 0x05, 0x00, 0x03, 0x82,
+0x01, 0x01, 0x00, 0x24, 0x28, 0xee, 0x22, 0x74,
+0x7f, 0x7c, 0xfa, 0x6c, 0x1f, 0xb3, 0x18, 0xd1,
+0xc2, 0x3d, 0x7d, 0x29, 0x42, 0x88, 0xad, 0x82,
+0xa5, 0xb1, 0x8a, 0x05, 0xd0, 0xec, 0x5c, 0x91,
+0x20, 0xf6, 0x82, 0xfd, 0xd5, 0x67, 0x60, 0x5f,
+0x31, 0xf5, 0xbd, 0x88, 0x91, 0x70, 0xbd, 0xb8,
+0xb9, 0x8c, 0x88, 0xfe, 0x53, 0xc9, 0x54, 0x9b,
+0x43, 0xc4, 0x7a, 0x43, 0x74, 0x6b, 0xdd, 0xb0,
+0xb1, 0x3b, 0x33, 0x45, 0x46, 0x78, 0xa3, 0x1c,
+0xef, 0x54, 0x68, 0xf7, 0x85, 0x9c, 0xe4, 0x51,
+0x6f, 0x06, 0xaf, 0x81, 0xdb, 0x2a, 0x7b, 0x7b,
+0x6f, 0xa8, 0x9c, 0x67, 0xd8, 0xcb, 0xc9, 0x91,
+0x40, 0x00, 0xae, 0xd9, 0xa1, 0x9f, 0xdd, 0xa6,
+0x43, 0x0e, 0x28, 0x7b, 0xaa, 0x1b, 0xe9, 0x84,
+0xdb, 0x76, 0x64, 0x42, 0x70, 0xc9, 0xc0, 0xeb,
+0xae, 0x84, 0x11, 0x16, 0x68, 0x4e, 0x84, 0x9e,
+0x7e, 0x92, 0x36, 0xee, 0x1c, 0x3b, 0x08, 0x63,
+0xeb, 0x79, 0x84, 0x15, 0x08, 0x9d, 0xaf, 0xc8,
+0x9a, 0xc7, 0x34, 0xd3, 0x94, 0x4b, 0xd1, 0x28,
+0x97, 0xbe, 0xd1, 0x45, 0x75, 0xdc, 0x35, 0x62,
+0xac, 0x1d, 0x1f, 0xb7, 0xb7, 0x15, 0x87, 0xc8,
+0x98, 0xc0, 0x24, 0x31, 0x56, 0x8d, 0xed, 0xdb,
+0x06, 0xc6, 0x46, 0xbf, 0x4b, 0x6d, 0xa6, 0xd5,
+0xab, 0xcc, 0x60, 0xfc, 0xe5, 0x37, 0xb6, 0x53,
+0x7d, 0x58, 0x95, 0xa9, 0x56, 0xc7, 0xf7, 0xee,
+0xc3, 0xa0, 0x76, 0xf7, 0x65, 0x4d, 0x53, 0xfa,
+0xff, 0x5f, 0x76, 0x33, 0x5a, 0x08, 0xfa, 0x86,
+0x92, 0x5a, 0x13, 0xfa, 0x1a, 0xfc, 0xf2, 0x1b,
+0x8c, 0x7f, 0x42, 0x6d, 0xb7, 0x7e, 0xb7, 0xb4,
+0xf0, 0xc7, 0x83, 0xbb, 0xa2, 0x81, 0x03, 0x2d,
+0xd4, 0x2a, 0x63, 0x3f, 0xf7, 0x31, 0x2e, 0x40,
+0x33, 0x5c, 0x46, 0xbc, 0x9b, 0xc1, 0x05, 0xa5,
+0x45, 0x4e, 0xc3,
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/core.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/core.c
@@ -5,7 +5,7 @@
  * Copyright 2006-2010		Johannes Berg <johannes@sipsolutions.net>
  * Copyright 2013-2014  Intel Mobile Communications GmbH
  * Copyright 2015-2017	Intel Deutschland GmbH
- * Copyright (C) 2018-2021 Intel Corporation
+ * Copyright (C) 2018-2022 Intel Corporation
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
@@ -216,7 +216,9 @@
 {
 	struct cfg80211_registered_device *rdev = data;
 
+	wiphy_lock(&rdev->wiphy);
 	rdev_rfkill_poll(rdev);
+	wiphy_unlock(&rdev->wiphy);
 }
 
 void cfg80211_stop_p2p_device(struct cfg80211_registered_device *rdev,
@@ -332,29 +334,20 @@
 void cfg80211_destroy_ifaces(struct cfg80211_registered_device *rdev)
 {
 	struct wireless_dev *wdev, *tmp;
-	bool found = false;
 
 	ASSERT_RTNL();
 
-	list_for_each_entry(wdev, &rdev->wiphy.wdev_list, list) {
+	list_for_each_entry_safe(wdev, tmp, &rdev->wiphy.wdev_list, list) {
 		if (wdev->nl_owner_dead) {
 			if (wdev->netdev)
 				dev_close(wdev->netdev);
-			found = true;
-		}
-	}
-
-	if (!found)
-		return;
 
-	wiphy_lock(&rdev->wiphy);
-	list_for_each_entry_safe(wdev, tmp, &rdev->wiphy.wdev_list, list) {
-		if (wdev->nl_owner_dead) {
+			wiphy_lock(&rdev->wiphy);
 			cfg80211_leave(rdev, wdev);
 			rdev_del_virtual_intf(rdev, wdev);
+			wiphy_unlock(&rdev->wiphy);
 		}
 	}
-	wiphy_unlock(&rdev->wiphy);
 }
 
 static void cfg80211_destroy_iface_wk(struct work_struct *work)
@@ -377,12 +370,12 @@
 	rdev = container_of(work, struct cfg80211_registered_device,
 			   sched_scan_stop_wk);
 
-	rtnl_lock();
+	wiphy_lock(&rdev->wiphy);
 	list_for_each_entry_safe(req, tmp, &rdev->sched_scan_req_list, list) {
 		if (req->nl_owner_dead)
 			cfg80211_stop_sched_scan_req(rdev, req, false);
 	}
-	rtnl_unlock();
+	wiphy_unlock(&rdev->wiphy);
 }
 
 static void cfg80211_propagate_radar_detect_wk(struct work_struct *work)
@@ -1081,6 +1074,16 @@
 	list_for_each_entry_safe(scan, tmp, &rdev->bss_list, list)
 		cfg80211_put_bss(&rdev->wiphy, &scan->pub);
 	mutex_destroy(&rdev->wiphy.mtx);
+
+	/*
+	 * The 'regd' can only be non-NULL if we never finished
+	 * initializing the wiphy and thus never went through the
+	 * unregister path - e.g. in failure scenarios. Thus, it
+	 * cannot have been visible to anyone if non-NULL, so we
+	 * can just free it here.
+	 */
+	kfree(rcu_dereference_raw(rdev->wiphy.regd));
+
 	kfree(rdev);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/debugfs.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/debugfs.c
@@ -65,9 +65,10 @@
 {
 	struct wiphy *wiphy = file->private_data;
 	char *buf;
-	unsigned int offset = 0, buf_size = PAGE_SIZE, i, r;
+	unsigned int offset = 0, buf_size = PAGE_SIZE, i;
 	enum nl80211_band band;
 	struct ieee80211_supported_band *sband;
+	ssize_t r;
 
 	buf = kzalloc(buf_size, GFP_KERNEL);
 	if (!buf)
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/nl80211.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/nl80211.c
@@ -314,6 +314,7 @@
 	[NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED] = { .type = NLA_FLAG },
 	[NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED] = { .type = NLA_FLAG },
 	[NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK] = { .type = NLA_FLAG },
+	[NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR] = { .type = NLA_U8 },
 };
 
 static const struct nla_policy
@@ -437,6 +438,10 @@
 	[NL80211_SAR_ATTR_SPECS] = NLA_POLICY_NESTED_ARRAY(sar_specs_policy),
 };
 
+static struct netlink_range_validation q_range = {
+	.max = INT_MAX,
+};
+
 static const struct nla_policy nl80211_policy[NUM_NL80211_ATTR] = {
 	[0] = { .strict_start_type = NL80211_ATTR_HE_OBSS_PD },
 	[NL80211_ATTR_WIPHY] = { .type = NLA_U32 },
@@ -509,7 +514,8 @@
 				   .len = IEEE80211_MAX_MESH_ID_LEN },
 	[NL80211_ATTR_MPATH_NEXT_HOP] = NLA_POLICY_ETH_ADDR_COMPAT,
 
-	[NL80211_ATTR_REG_ALPHA2] = { .type = NLA_STRING, .len = 2 },
+	/* allow 3 for NUL-termination, we used to declare this NLA_STRING */
+	[NL80211_ATTR_REG_ALPHA2] = NLA_POLICY_RANGE(NLA_BINARY, 2, 3),
 	[NL80211_ATTR_REG_RULES] = { .type = NLA_NESTED },
 
 	[NL80211_ATTR_BSS_CTS_PROT] = { .type = NLA_U8 },
@@ -718,7 +724,7 @@
 
 	[NL80211_ATTR_TXQ_LIMIT] = { .type = NLA_U32 },
 	[NL80211_ATTR_TXQ_MEMORY_LIMIT] = { .type = NLA_U32 },
-	[NL80211_ATTR_TXQ_QUANTUM] = { .type = NLA_U32 },
+	[NL80211_ATTR_TXQ_QUANTUM] = NLA_POLICY_FULL_RANGE(NLA_U32, &q_range),
 	[NL80211_ATTR_HE_CAPABILITY] =
 		NLA_POLICY_RANGE(NLA_BINARY,
 				 NL80211_HE_MIN_CAPABILITY_LEN,
@@ -922,33 +928,37 @@
 	[NL80211_PKTPAT_OFFSET] = { .type = NLA_U32 },
 };
 
-int nl80211_prepare_wdev_dump(struct netlink_callback *cb,
-			      struct cfg80211_registered_device **rdev,
-			      struct wireless_dev **wdev)
+static int nl80211_prepare_wdev_dump(struct netlink_callback *cb,
+				     struct cfg80211_registered_device **rdev,
+				     struct wireless_dev **wdev,
+				     struct nlattr **attrbuf)
 {
 	int err;
 
 	if (!cb->args[0]) {
-		struct nlattr **attrbuf;
+		struct nlattr **attrbuf_free = NULL;
 
-		attrbuf = kcalloc(NUM_NL80211_ATTR, sizeof(*attrbuf),
-				  GFP_KERNEL);
-		if (!attrbuf)
-			return -ENOMEM;
+		if (!attrbuf) {
+			attrbuf = kcalloc(NUM_NL80211_ATTR, sizeof(*attrbuf),
+					  GFP_KERNEL);
+			if (!attrbuf)
+				return -ENOMEM;
+			attrbuf_free = attrbuf;
+		}
 
 		err = nlmsg_parse_deprecated(cb->nlh,
 					     GENL_HDRLEN + nl80211_fam.hdrsize,
 					     attrbuf, nl80211_fam.maxattr,
 					     nl80211_policy, NULL);
 		if (err) {
-			kfree(attrbuf);
+			kfree(attrbuf_free);
 			return err;
 		}
 
 		rtnl_lock();
 		*wdev = __cfg80211_wdev_from_attrs(NULL, sock_net(cb->skb->sk),
 						   attrbuf);
-		kfree(attrbuf);
+		kfree(attrbuf_free);
 		if (IS_ERR(*wdev)) {
 			rtnl_unlock();
 			return PTR_ERR(*wdev);
@@ -3075,6 +3085,15 @@
 	} else if (attrs[NL80211_ATTR_CHANNEL_WIDTH]) {
 		chandef->width =
 			nla_get_u32(attrs[NL80211_ATTR_CHANNEL_WIDTH]);
+		if (chandef->chan->band == NL80211_BAND_S1GHZ) {
+			/* User input error for channel width doesn't match channel  */
+			if (chandef->width != ieee80211_s1g_channel_width(chandef->chan)) {
+				NL_SET_ERR_MSG_ATTR(extack,
+						    attrs[NL80211_ATTR_CHANNEL_WIDTH],
+						    "bad channel width");
+				return -EINVAL;
+			}
+		}
 		if (attrs[NL80211_ATTR_CENTER_FREQ1]) {
 			chandef->center_freq1 =
 				nla_get_u32(attrs[NL80211_ATTR_CENTER_FREQ1]);
@@ -3612,6 +3631,7 @@
 	wdev_lock(wdev);
 	switch (wdev->iftype) {
 	case NL80211_IFTYPE_AP:
+	case NL80211_IFTYPE_P2P_GO:
 		if (wdev->ssid_len &&
 		    nla_put(msg, NL80211_ATTR_SSID, wdev->ssid_len, wdev->ssid))
 			goto nla_put_failure_locked;
@@ -3721,6 +3741,7 @@
 			if_idx++;
 		}
 
+		if_start = 0;
 		wp_idx++;
 	}
  out:
@@ -3779,6 +3800,11 @@
 		if (flags[flag])
 			*mntrflags |= (1<<flag);
 
+	/* cooked monitor mode is incompatible with other modes */
+	if (*mntrflags & MONITOR_FLAG_COOK_FRAMES &&
+	    *mntrflags != MONITOR_FLAG_COOK_FRAMES)
+		return -EOPNOTSUPP;
+
 	*mntrflags |= MONITOR_FLAG_CHANGED;
 
 	return 0;
@@ -3897,6 +3923,8 @@
 
 		if (ntype != NL80211_IFTYPE_MESH_POINT)
 			return -EINVAL;
+		if (otype != NL80211_IFTYPE_MESH_POINT)
+			return -EINVAL;
 		if (netif_running(dev))
 			return -EBUSY;
 
@@ -4118,10 +4146,7 @@
 	struct nlattr *key;
 	struct get_key_cookie *cookie = c;
 
-	if ((params->key &&
-	     nla_put(cookie->msg, NL80211_ATTR_KEY_DATA,
-		     params->key_len, params->key)) ||
-	    (params->seq &&
+	if ((params->seq &&
 	     nla_put(cookie->msg, NL80211_ATTR_KEY_SEQ,
 		     params->seq_len, params->seq)) ||
 	    (params->cipher &&
@@ -4133,10 +4158,7 @@
 	if (!key)
 		goto nla_put_failure;
 
-	if ((params->key &&
-	     nla_put(cookie->msg, NL80211_KEY_DATA,
-		     params->key_len, params->key)) ||
-	    (params->seq &&
+	if ((params->seq &&
 	     nla_put(cookie->msg, NL80211_KEY_SEQ,
 		     params->seq_len, params->seq)) ||
 	    (params->cipher &&
@@ -6001,7 +6023,7 @@
 	int sta_idx = cb->args[2];
 	int err;
 
-	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev);
+	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev, NULL);
 	if (err)
 		return err;
 	/* nl80211_prepare_wdev_dump acquired it in the successful case */
@@ -6896,7 +6918,7 @@
 	int path_idx = cb->args[2];
 	int err;
 
-	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev);
+	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev, NULL);
 	if (err)
 		return err;
 	/* nl80211_prepare_wdev_dump acquired it in the successful case */
@@ -7096,7 +7118,7 @@
 	int path_idx = cb->args[2];
 	int err;
 
-	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev);
+	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev, NULL);
 	if (err)
 		return err;
 	/* nl80211_prepare_wdev_dump acquired it in the successful case */
@@ -7648,7 +7670,7 @@
 	struct cfg80211_registered_device *rdev = info->user_ptr[0];
 	struct net_device *dev = info->user_ptr[1];
 	struct wireless_dev *wdev = dev->ieee80211_ptr;
-	struct mesh_config cfg;
+	struct mesh_config cfg = {};
 	u32 mask;
 	int err;
 
@@ -8767,7 +8789,8 @@
 		return ERR_PTR(-ENOMEM);
 
 	if (n_ssids)
-		request->ssids = (void *)&request->channels[n_channels];
+		request->ssids = (void *)request +
+			struct_size(request, channels, n_channels);
 	request->n_ssids = n_ssids;
 	if (ie_len) {
 		if (n_ssids)
@@ -9518,7 +9541,7 @@
 	int start = cb->args[2], idx = 0;
 	int err;
 
-	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev);
+	err = nl80211_prepare_wdev_dump(cb, &rdev, &wdev, NULL);
 	if (err)
 		return err;
 	/* nl80211_prepare_wdev_dump acquired it in the successful case */
@@ -9651,7 +9674,7 @@
 	if (!attrbuf)
 		return -ENOMEM;
 
-	res = nl80211_prepare_wdev_dump(cb, &rdev, &wdev);
+	res = nl80211_prepare_wdev_dump(cb, &rdev, &wdev, attrbuf);
 	if (res) {
 		kfree(attrbuf);
 		return res;
@@ -11327,18 +11350,23 @@
 	struct cfg80211_bitrate_mask mask;
 	struct cfg80211_registered_device *rdev = info->user_ptr[0];
 	struct net_device *dev = info->user_ptr[1];
+	struct wireless_dev *wdev = dev->ieee80211_ptr;
 	int err;
 
 	if (!rdev->ops->set_bitrate_mask)
 		return -EOPNOTSUPP;
 
+	wdev_lock(wdev);
 	err = nl80211_parse_tx_bitrate_mask(info, info->attrs,
 					    NL80211_ATTR_TX_RATES, &mask,
 					    dev, true);
 	if (err)
-		return err;
+		goto out;
 
-	return rdev_set_bitrate_mask(rdev, dev, NULL, &mask);
+	err = rdev_set_bitrate_mask(rdev, dev, NULL, &mask);
+out:
+	wdev_unlock(wdev);
+	return err;
 }
 
 static int nl80211_register_mgmt(struct sk_buff *skb, struct genl_info *info)
@@ -12866,6 +12894,8 @@
 error:
 	for (i = 0; i < new_coalesce.n_rules; i++) {
 		tmp_rule = &new_coalesce.rules[i];
+		if (!tmp_rule)
+			continue;
 		for (j = 0; j < tmp_rule->n_patterns; j++)
 			kfree(tmp_rule->patterns[j].mask);
 		kfree(tmp_rule->patterns);
@@ -12902,7 +12932,7 @@
 		return -ERANGE;
 	if (nla_len(tb[NL80211_REKEY_DATA_KCK]) != NL80211_KCK_LEN &&
 	    !(rdev->wiphy.flags & WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK &&
-	      nla_len(tb[NL80211_REKEY_DATA_KEK]) == NL80211_KCK_EXT_LEN))
+	      nla_len(tb[NL80211_REKEY_DATA_KCK]) == NL80211_KCK_EXT_LEN))
 		return -ERANGE;
 
 	rekey_data.kek = nla_data(tb[NL80211_REKEY_DATA_KEK]);
@@ -13173,6 +13203,9 @@
 	i = 0;
 	nla_for_each_nested(attr, attr_filter, rem) {
 		filter[i].filter = nla_memdup(attr, GFP_KERNEL);
+		if (!filter[i].filter)
+			goto err;
+
 		filter[i].len = nla_len(attr);
 		i++;
 	}
@@ -13185,6 +13218,15 @@
 	}
 
 	return 0;
+
+err:
+	i = 0;
+	nla_for_each_nested(attr, attr_filter, rem) {
+		kfree(filter[i].filter);
+		i++;
+	}
+	kfree(filter);
+	return -ENOMEM;
 }
 
 static int nl80211_nan_add_func(struct sk_buff *skb,
@@ -15904,8 +15946,7 @@
 		.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
 		.doit = nl80211_color_change,
 		.flags = GENL_UNS_ADMIN_PERM,
-		.internal_flags = NL80211_FLAG_NEED_NETDEV_UP |
-				  NL80211_FLAG_NEED_RTNL,
+		.internal_flags = NL80211_FLAG_NEED_NETDEV_UP,
 	},
 };
 
@@ -16226,10 +16267,8 @@
 
 	genlmsg_end(msg, hdr);
 
-	rcu_read_lock();
 	genlmsg_multicast_allns(&nl80211_fam, msg, 0,
-				NL80211_MCGRP_REGULATORY, GFP_ATOMIC);
-	rcu_read_unlock();
+				NL80211_MCGRP_REGULATORY);
 
 	return;
 
@@ -16743,10 +16782,8 @@
 
 	genlmsg_end(msg, hdr);
 
-	rcu_read_lock();
 	genlmsg_multicast_allns(&nl80211_fam, msg, 0,
-				NL80211_MCGRP_REGULATORY, GFP_ATOMIC);
-	rcu_read_unlock();
+				NL80211_MCGRP_REGULATORY);
 
 	return;
 
@@ -17509,7 +17546,8 @@
 	wdev->chandef = *chandef;
 	wdev->preset_chandef = *chandef;
 
-	if (wdev->iftype == NL80211_IFTYPE_STATION &&
+	if ((wdev->iftype == NL80211_IFTYPE_STATION ||
+	     wdev->iftype == NL80211_IFTYPE_P2P_CLIENT) &&
 	    !WARN_ON(!wdev->current_bss))
 		cfg80211_update_assoc_bss_entry(wdev, chandef->chan);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/nl80211.h
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/nl80211.h
@@ -1,7 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
  * Portions of this file
- * Copyright (C) 2018, 2020 Intel Corporation
+ * Copyright (C) 2018, 2020-2021 Intel Corporation
  */
 #ifndef __NET_WIRELESS_NL80211_H
 #define __NET_WIRELESS_NL80211_H
@@ -22,10 +22,6 @@
 	       ((u64)wiphy_to_rdev(wdev->wiphy)->wiphy_idx << 32);
 }
 
-int nl80211_prepare_wdev_dump(struct netlink_callback *cb,
-			      struct cfg80211_registered_device **rdev,
-			      struct wireless_dev **wdev);
-
 int nl80211_parse_chandef(struct cfg80211_registered_device *rdev,
 			  struct genl_info *info,
 			  struct cfg80211_chan_def *chandef);
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/pmsr.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/pmsr.c
@@ -58,7 +58,7 @@
 	out->ftm.burst_period = 0;
 	if (tb[NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD])
 		out->ftm.burst_period =
-			nla_get_u32(tb[NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD]);
+			nla_get_u16(tb[NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD]);
 
 	out->ftm.asap = !!tb[NL80211_PMSR_FTM_REQ_ATTR_ASAP];
 	if (out->ftm.asap && !capa->ftm.asap) {
@@ -77,7 +77,7 @@
 	out->ftm.num_bursts_exp = 0;
 	if (tb[NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP])
 		out->ftm.num_bursts_exp =
-			nla_get_u32(tb[NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP]);
+			nla_get_u8(tb[NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP]);
 
 	if (capa->ftm.max_bursts_exponent >= 0 &&
 	    out->ftm.num_bursts_exp > capa->ftm.max_bursts_exponent) {
@@ -90,7 +90,7 @@
 	out->ftm.burst_duration = 15;
 	if (tb[NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION])
 		out->ftm.burst_duration =
-			nla_get_u32(tb[NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION]);
+			nla_get_u8(tb[NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION]);
 
 	out->ftm.ftms_per_burst = 0;
 	if (tb[NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST])
@@ -109,7 +109,7 @@
 	out->ftm.ftmr_retries = 3;
 	if (tb[NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES])
 		out->ftm.ftmr_retries =
-			nla_get_u32(tb[NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES]);
+			nla_get_u8(tb[NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES]);
 
 	out->ftm.request_lci = !!tb[NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI];
 	if (out->ftm.request_lci && !capa->ftm.request_lci) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/reg.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/reg.c
@@ -404,7 +404,8 @@
 {
 	if (!alpha2)
 		return false;
-	return isalpha(alpha2[0]) && isalpha(alpha2[1]);
+	return isascii(alpha2[0]) && isalpha(alpha2[0]) &&
+	       isascii(alpha2[1]) && isalpha(alpha2[1]);
 }
 
 static bool alpha2_equal(const char *alpha2_x, const char *alpha2_y)
@@ -806,6 +807,8 @@
 	return 0;
 }
 
+MODULE_FIRMWARE("regulatory.db.p7s");
+
 static bool regdb_has_valid_signature(const u8 *data, unsigned int size)
 {
 	const struct firmware *sig;
@@ -1077,8 +1080,12 @@
 	release_firmware(fw);
 }
 
+MODULE_FIRMWARE("regulatory.db");
+
 static int query_regdb_file(const char *alpha2)
 {
+	int err;
+
 	ASSERT_RTNL();
 
 	if (regdb)
@@ -1088,9 +1095,13 @@
 	if (!alpha2)
 		return -ENOMEM;
 
-	return request_firmware_nowait(THIS_MODULE, true, "regulatory.db",
-				       &reg_pdev->dev, GFP_KERNEL,
-				       (void *)alpha2, regdb_fw_cb);
+	err = request_firmware_nowait(THIS_MODULE, true, "regulatory.db",
+				      &reg_pdev->dev, GFP_KERNEL,
+				      (void *)alpha2, regdb_fw_cb);
+	if (err)
+		kfree(alpha2);
+
+	return err;
 }
 
 int reg_reload_regdb(void)
@@ -2338,6 +2349,7 @@
 	struct cfg80211_chan_def chandef = {};
 	struct cfg80211_registered_device *rdev = wiphy_to_rdev(wiphy);
 	enum nl80211_iftype iftype;
+	bool ret;
 
 	wdev_lock(wdev);
 	iftype = wdev->iftype;
@@ -2387,7 +2399,9 @@
 	case NL80211_IFTYPE_AP:
 	case NL80211_IFTYPE_P2P_GO:
 	case NL80211_IFTYPE_ADHOC:
-		return cfg80211_reg_can_beacon_relax(wiphy, &chandef, iftype);
+		ret = cfg80211_reg_can_beacon_relax(wiphy, &chandef, iftype);
+
+		return ret;
 	case NL80211_IFTYPE_STATION:
 	case NL80211_IFTYPE_P2P_CLIENT:
 		return cfg80211_chandef_usable(wiphy, &chandef,
@@ -2408,11 +2422,11 @@
 	struct wireless_dev *wdev;
 	struct cfg80211_registered_device *rdev = wiphy_to_rdev(wiphy);
 
-	ASSERT_RTNL();
-
+	wiphy_lock(wiphy);
 	list_for_each_entry(wdev, &rdev->wiphy.wdev_list, list)
 		if (!reg_wdev_chan_valid(wiphy, wdev))
 			cfg80211_leave(rdev, wdev);
+	wiphy_unlock(wiphy);
 }
 
 static void reg_check_chans_work(struct work_struct *work)
@@ -4232,8 +4246,10 @@
 		return -EINVAL;
 
 	err = load_builtin_regdb_keys();
-	if (err)
+	if (err) {
+		platform_device_unregister(reg_pdev);
 		return err;
+	}
 
 	/* We always try to get an update for the static regdomain */
 	err = regulatory_hint_core(cfg80211_world_regdom->alpha2);
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/scan.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/scan.c
@@ -143,18 +143,12 @@
 	lockdep_assert_held(&rdev->bss_lock);
 
 	bss->refcount++;
-	if (bss->pub.hidden_beacon_bss) {
-		bss = container_of(bss->pub.hidden_beacon_bss,
-				   struct cfg80211_internal_bss,
-				   pub);
-		bss->refcount++;
-	}
-	if (bss->pub.transmitted_bss) {
-		bss = container_of(bss->pub.transmitted_bss,
-				   struct cfg80211_internal_bss,
-				   pub);
-		bss->refcount++;
-	}
+
+	if (bss->pub.hidden_beacon_bss)
+		bss_from_pub(bss->pub.hidden_beacon_bss)->refcount++;
+
+	if (bss->pub.transmitted_bss)
+		bss_from_pub(bss->pub.transmitted_bss)->refcount++;
 }
 
 static inline void bss_ref_put(struct cfg80211_registered_device *rdev,
@@ -268,114 +262,152 @@
 }
 EXPORT_SYMBOL(cfg80211_is_element_inherited);
 
-static size_t cfg80211_gen_new_ie(const u8 *ie, size_t ielen,
-				  const u8 *subelement, size_t subie_len,
-				  u8 *new_ie, gfp_t gfp)
+static size_t cfg80211_copy_elem_with_frags(const struct element *elem,
+					    const u8 *ie, size_t ie_len,
+					    u8 **pos, u8 *buf, size_t buf_len)
 {
-	u8 *pos, *tmp;
-	const u8 *tmp_old, *tmp_new;
-	const struct element *non_inherit_elem;
-	u8 *sub_copy;
+	if (WARN_ON((u8 *)elem < ie || elem->data > ie + ie_len ||
+		    elem->data + elem->datalen > ie + ie_len))
+		return 0;
 
-	/* copy subelement as we need to change its content to
-	 * mark an ie after it is processed.
-	 */
-	sub_copy = kmemdup(subelement, subie_len, gfp);
-	if (!sub_copy)
+	if (elem->datalen + 2 > buf + buf_len - *pos)
 		return 0;
 
-	pos = &new_ie[0];
+	memcpy(*pos, elem, elem->datalen + 2);
+	*pos += elem->datalen + 2;
 
-	/* set new ssid */
-	tmp_new = cfg80211_find_ie(WLAN_EID_SSID, sub_copy, subie_len);
-	if (tmp_new) {
-		memcpy(pos, tmp_new, tmp_new[1] + 2);
-		pos += (tmp_new[1] + 2);
-	}
-
-	/* get non inheritance list if exists */
-	non_inherit_elem =
-		cfg80211_find_ext_elem(WLAN_EID_EXT_NON_INHERITANCE,
-				       sub_copy, subie_len);
+	/* Finish if it is not fragmented  */
+	if (elem->datalen != 255)
+		return *pos - buf;
 
-	/* go through IEs in ie (skip SSID) and subelement,
-	 * merge them into new_ie
-	 */
-	tmp_old = cfg80211_find_ie(WLAN_EID_SSID, ie, ielen);
-	tmp_old = (tmp_old) ? tmp_old + tmp_old[1] + 2 : ie;
+	ie_len = ie + ie_len - elem->data - elem->datalen;
+	ie = (const u8 *)elem->data + elem->datalen;
+
+	for_each_element(elem, ie, ie_len) {
+		if (elem->id != WLAN_EID_FRAGMENT)
+			break;
 
-	while (tmp_old + tmp_old[1] + 2 - ie <= ielen) {
-		if (tmp_old[0] == 0) {
-			tmp_old++;
+		if (elem->datalen + 2 > buf + buf_len - *pos)
+			return 0;
+
+		memcpy(*pos, elem, elem->datalen + 2);
+		*pos += elem->datalen + 2;
+
+		if (elem->datalen != 255)
+			break;
+	}
+
+	return *pos - buf;
+}
+
+static size_t cfg80211_gen_new_ie(const u8 *ie, size_t ielen,
+				  const u8 *subie, size_t subie_len,
+				  u8 *new_ie, size_t new_ie_len)
+{
+	const struct element *non_inherit_elem, *parent, *sub;
+	u8 *pos = new_ie;
+	u8 id, ext_id;
+	unsigned int match_len;
+
+	non_inherit_elem = cfg80211_find_ext_elem(WLAN_EID_EXT_NON_INHERITANCE,
+						  subie, subie_len);
+
+	/* We copy the elements one by one from the parent to the generated
+	 * elements.
+	 * If they are not inherited (included in subie or in the non
+	 * inheritance element), then we copy all occurrences the first time
+	 * we see this element type.
+	 */
+	for_each_element(parent, ie, ielen) {
+		if (parent->id == WLAN_EID_FRAGMENT)
 			continue;
+
+		if (parent->id == WLAN_EID_EXTENSION) {
+			if (parent->datalen < 1)
+				continue;
+
+			id = WLAN_EID_EXTENSION;
+			ext_id = parent->data[0];
+			match_len = 1;
+		} else {
+			id = parent->id;
+			match_len = 0;
 		}
 
-		if (tmp_old[0] == WLAN_EID_EXTENSION)
-			tmp = (u8 *)cfg80211_find_ext_ie(tmp_old[2], sub_copy,
-							 subie_len);
-		else
-			tmp = (u8 *)cfg80211_find_ie(tmp_old[0], sub_copy,
-						     subie_len);
+		/* Find first occurrence in subie */
+		sub = cfg80211_find_elem_match(id, subie, subie_len,
+					       &ext_id, match_len, 0);
 
-		if (!tmp) {
-			const struct element *old_elem = (void *)tmp_old;
+		/* Copy from parent if not in subie and inherited */
+		if (!sub &&
+		    cfg80211_is_element_inherited(parent, non_inherit_elem)) {
+			if (!cfg80211_copy_elem_with_frags(parent,
+							   ie, ielen,
+							   &pos, new_ie,
+							   new_ie_len))
+				return 0;
 
-			/* ie in old ie but not in subelement */
-			if (cfg80211_is_element_inherited(old_elem,
-							  non_inherit_elem)) {
-				memcpy(pos, tmp_old, tmp_old[1] + 2);
-				pos += tmp_old[1] + 2;
-			}
-		} else {
-			/* ie in transmitting ie also in subelement,
-			 * copy from subelement and flag the ie in subelement
-			 * as copied (by setting eid field to WLAN_EID_SSID,
-			 * which is skipped anyway).
-			 * For vendor ie, compare OUI + type + subType to
-			 * determine if they are the same ie.
-			 */
-			if (tmp_old[0] == WLAN_EID_VENDOR_SPECIFIC) {
-				if (!memcmp(tmp_old + 2, tmp + 2, 5)) {
-					/* same vendor ie, copy from
-					 * subelement
-					 */
-					memcpy(pos, tmp, tmp[1] + 2);
-					pos += tmp[1] + 2;
-					tmp[0] = WLAN_EID_SSID;
-				} else {
-					memcpy(pos, tmp_old, tmp_old[1] + 2);
-					pos += tmp_old[1] + 2;
-				}
-			} else {
-				/* copy ie from subelement into new ie */
-				memcpy(pos, tmp, tmp[1] + 2);
-				pos += tmp[1] + 2;
-				tmp[0] = WLAN_EID_SSID;
-			}
+			continue;
 		}
 
-		if (tmp_old + tmp_old[1] + 2 - ie == ielen)
-			break;
+		/* Already copied if an earlier element had the same type */
+		if (cfg80211_find_elem_match(id, ie, (u8 *)parent - ie,
+					     &ext_id, match_len, 0))
+			continue;
+
+		/* Not inheriting, copy all similar elements from subie */
+		while (sub) {
+			if (!cfg80211_copy_elem_with_frags(sub,
+							   subie, subie_len,
+							   &pos, new_ie,
+							   new_ie_len))
+				return 0;
 
-		tmp_old += tmp_old[1] + 2;
+			sub = cfg80211_find_elem_match(id,
+						       sub->data + sub->datalen,
+						       subie_len + subie -
+						       (sub->data +
+							sub->datalen),
+						       &ext_id, match_len, 0);
+		}
 	}
 
-	/* go through subelement again to check if there is any ie not
-	 * copied to new ie, skip ssid, capability, bssid-index ie
+	/* The above misses elements that are included in subie but not in the
+	 * parent, so do a pass over subie and append those.
+	 * Skip the non-tx BSSID caps and non-inheritance element.
 	 */
-	tmp_new = sub_copy;
-	while (tmp_new + tmp_new[1] + 2 - sub_copy <= subie_len) {
-		if (!(tmp_new[0] == WLAN_EID_NON_TX_BSSID_CAP ||
-		      tmp_new[0] == WLAN_EID_SSID)) {
-			memcpy(pos, tmp_new, tmp_new[1] + 2);
-			pos += tmp_new[1] + 2;
+	for_each_element(sub, subie, subie_len) {
+		if (sub->id == WLAN_EID_NON_TX_BSSID_CAP)
+			continue;
+
+		if (sub->id == WLAN_EID_FRAGMENT)
+			continue;
+
+		if (sub->id == WLAN_EID_EXTENSION) {
+			if (sub->datalen < 1)
+				continue;
+
+			id = WLAN_EID_EXTENSION;
+			ext_id = sub->data[0];
+			match_len = 1;
+
+			if (ext_id == WLAN_EID_EXT_NON_INHERITANCE)
+				continue;
+		} else {
+			id = sub->id;
+			match_len = 0;
 		}
-		if (tmp_new + tmp_new[1] + 2 - sub_copy == subie_len)
-			break;
-		tmp_new += tmp_new[1] + 2;
+
+		/* Processed if one was included in the parent */
+		if (cfg80211_find_elem_match(id, ie, ielen,
+					     &ext_id, match_len, 0))
+			continue;
+
+		if (!cfg80211_copy_elem_with_frags(sub, subie, subie_len,
+						   &pos, new_ie, new_ie_len))
+			return 0;
 	}
 
-	kfree(sub_copy);
 	return pos - new_ie;
 }
 
@@ -429,6 +461,15 @@
 
 	rcu_read_unlock();
 
+	/*
+	 * This is a bit weird - it's not on the list, but already on another
+	 * one! The only way that could happen is if there's some BSSID/SSID
+	 * shared by multiple APs in their multi-BSSID profiles, potentially
+	 * with hidden SSID mixed in ... ignore it.
+	 */
+	if (!list_empty(&nontrans_bss->nontrans_list))
+		return -EINVAL;
+
 	/* add to the list */
 	list_add_tail(&nontrans_bss->nontrans_list, &trans_bss->nontrans_list);
 	return 0;
@@ -600,7 +641,7 @@
 
 	ret = cfg80211_calc_short_ssid(ies, &ssid_elem, &s_ssid_tmp);
 	if (ret)
-		return ret;
+		return 0;
 
 	/* RNR IE may contain more than one NEIGHBOR_AP_INFO */
 	while (pos + sizeof(*ap_info) <= end) {
@@ -702,8 +743,12 @@
 
 	for (i = 0; i < request->n_ssids; i++) {
 		/* wildcard ssid in the scan request */
-		if (!request->ssids[i].ssid_len)
+		if (!request->ssids[i].ssid_len) {
+			if (ap->multi_bss && !ap->transmitted_bssid)
+				continue;
+
 			return true;
+		}
 
 		if (ap->ssid_len &&
 		    ap->ssid_len == request->ssids[i].ssid_len) {
@@ -751,10 +796,45 @@
 		list_for_each_entry(intbss, &rdev->bss_list, list) {
 			struct cfg80211_bss *res = &intbss->pub;
 			const struct cfg80211_bss_ies *ies;
+			const struct element *ssid_elem;
+			struct cfg80211_colocated_ap *entry;
+			u32 s_ssid_tmp;
+			int ret;
 
 			ies = rcu_access_pointer(res->ies);
 			count += cfg80211_parse_colocated_ap(ies,
 							     &coloc_ap_list);
+
+			/* In case the scan request specified a specific BSSID
+			 * and the BSS is found and operating on 6GHz band then
+			 * add this AP to the collocated APs list.
+			 * This is relevant for ML probe requests when the lower
+			 * band APs have not been discovered.
+			 */
+			if (is_broadcast_ether_addr(rdev_req->bssid) ||
+			    !ether_addr_equal(rdev_req->bssid, res->bssid) ||
+			    res->channel->band != NL80211_BAND_6GHZ)
+				continue;
+
+			ret = cfg80211_calc_short_ssid(ies, &ssid_elem,
+						       &s_ssid_tmp);
+			if (ret)
+				continue;
+
+			entry = kzalloc(sizeof(*entry), GFP_ATOMIC);
+			if (!entry)
+				continue;
+
+			memcpy(entry->bssid, res->bssid, ETH_ALEN);
+			entry->short_ssid = s_ssid_tmp;
+			memcpy(entry->ssid, ssid_elem->data,
+			       ssid_elem->datalen);
+			entry->ssid_len = ssid_elem->datalen;
+			entry->short_ssid_valid = true;
+			entry->center_freq = res->channel->center_freq;
+
+			list_add_tail(&entry->list, &coloc_ap_list);
+			count++;
 		}
 		spin_unlock_bh(&rdev->bss_lock);
 	}
@@ -829,6 +909,13 @@
 		    !cfg80211_find_ssid_match(ap, request))
 			continue;
 
+		if (!is_broadcast_ether_addr(request->bssid) &&
+		    !ether_addr_equal(request->bssid, ap->bssid))
+			continue;
+
+		if (!request->n_ssids && ap->multi_bss && !ap->transmitted_bssid)
+			continue;
+
 		cfg80211_scan_req_add_chan(request, chan, true);
 		memcpy(scan_6ghz_params->bssid, ap->bssid, ETH_ALEN);
 		scan_6ghz_params->short_ssid = ap->short_ssid;
@@ -1465,7 +1552,7 @@
 }
 EXPORT_SYMBOL(cfg80211_get_bss);
 
-static void rb_insert_bss(struct cfg80211_registered_device *rdev,
+static bool rb_insert_bss(struct cfg80211_registered_device *rdev,
 			  struct cfg80211_internal_bss *bss)
 {
 	struct rb_node **p = &rdev->bss_tree.rb_node;
@@ -1481,7 +1568,7 @@
 
 		if (WARN_ON(!cmp)) {
 			/* will sort of leak this BSS */
-			return;
+			return false;
 		}
 
 		if (cmp < 0)
@@ -1492,6 +1579,7 @@
 
 	rb_link_node(&bss->rbn, parent, p);
 	rb_insert_color(&bss->rbn, &rdev->bss_tree);
+	return true;
 }
 
 static struct cfg80211_internal_bss *
@@ -1518,6 +1606,34 @@
 	return NULL;
 }
 
+static void cfg80211_insert_bss(struct cfg80211_registered_device *rdev,
+				struct cfg80211_internal_bss *bss)
+{
+	lockdep_assert_held(&rdev->bss_lock);
+
+	if (!rb_insert_bss(rdev, bss))
+		return;
+	list_add_tail(&bss->list, &rdev->bss_list);
+	rdev->bss_entries++;
+}
+
+static void cfg80211_rehash_bss(struct cfg80211_registered_device *rdev,
+                                struct cfg80211_internal_bss *bss)
+{
+	lockdep_assert_held(&rdev->bss_lock);
+
+	rb_erase(&bss->rbn, &rdev->bss_tree);
+	if (!rb_insert_bss(rdev, bss)) {
+		list_del(&bss->list);
+		if (!list_empty(&bss->hidden_list))
+			list_del_init(&bss->hidden_list);
+		if (!list_empty(&bss->pub.nontrans_list))
+			list_del_init(&bss->pub.nontrans_list);
+		rdev->bss_entries--;
+	}
+	rdev->bss_generation++;
+}
+
 static bool cfg80211_combine_bsses(struct cfg80211_registered_device *rdev,
 				   struct cfg80211_internal_bss *new)
 {
@@ -1597,6 +1713,23 @@
 	u8 bssid_index;
 };
 
+static void cfg80211_update_hidden_bsses(struct cfg80211_internal_bss *known,
+					 const struct cfg80211_bss_ies *new_ies,
+					 const struct cfg80211_bss_ies *old_ies)
+{
+	struct cfg80211_internal_bss *bss;
+
+	/* Assign beacon IEs to all sub entries */
+	list_for_each_entry(bss, &known->hidden_list, hidden_list) {
+		const struct cfg80211_bss_ies *ies;
+
+		ies = rcu_access_pointer(bss->pub.beacon_ies);
+		WARN_ON(ies != old_ies);
+
+		rcu_assign_pointer(bss->pub.beacon_ies, new_ies);
+	}
+}
+
 static bool
 cfg80211_update_known_bss(struct cfg80211_registered_device *rdev,
 			  struct cfg80211_internal_bss *known,
@@ -1620,7 +1753,6 @@
 			kfree_rcu((struct cfg80211_bss_ies *)old, rcu_head);
 	} else if (rcu_access_pointer(new->pub.beacon_ies)) {
 		const struct cfg80211_bss_ies *old;
-		struct cfg80211_internal_bss *bss;
 
 		if (known->pub.hidden_beacon_bss &&
 		    !list_empty(&known->hidden_list)) {
@@ -1648,16 +1780,9 @@
 		if (old == rcu_access_pointer(known->pub.ies))
 			rcu_assign_pointer(known->pub.ies, new->pub.beacon_ies);
 
-		/* Assign beacon IEs to all sub entries */
-		list_for_each_entry(bss, &known->hidden_list, hidden_list) {
-			const struct cfg80211_bss_ies *ies;
-
-			ies = rcu_access_pointer(bss->pub.beacon_ies);
-			WARN_ON(ies != old);
-
-			rcu_assign_pointer(bss->pub.beacon_ies,
-					   new->pub.beacon_ies);
-		}
+		cfg80211_update_hidden_bsses(known,
+					     rcu_access_pointer(new->pub.beacon_ies),
+					     old);
 
 		if (old)
 			kfree_rcu((struct cfg80211_bss_ies *)old, rcu_head);
@@ -1734,6 +1859,8 @@
 		new->refcount = 1;
 		INIT_LIST_HEAD(&new->hidden_list);
 		INIT_LIST_HEAD(&new->pub.nontrans_list);
+		/* we'll set this later if it was non-NULL */
+		new->pub.transmitted_bss = NULL;
 
 		if (rcu_access_pointer(tmp->pub.proberesp_ies)) {
 			hidden = rb_find_bss(rdev, tmp, BSS_CMP_HIDE_ZLEN);
@@ -1745,8 +1872,12 @@
 				list_add(&new->hidden_list,
 					 &hidden->hidden_list);
 				hidden->refcount++;
+
+				ies = (void *)rcu_access_pointer(new->pub.beacon_ies);
 				rcu_assign_pointer(new->pub.beacon_ies,
 						   hidden->pub.beacon_ies);
+				if (ies)
+					kfree_rcu(ies, rcu_head);
 			}
 		} else {
 			/*
@@ -1778,9 +1909,7 @@
 			bss_ref_get(rdev, pbss);
 		}
 
-		list_add_tail(&new->list, &rdev->bss_list);
-		rdev->bss_entries++;
-		rb_insert_bss(rdev, new);
+		cfg80211_insert_bss(rdev, new);
 		found = new;
 	}
 
@@ -1971,11 +2100,18 @@
 		/* this is a nontransmitting bss, we need to add it to
 		 * transmitting bss' list if it is not there
 		 */
+		spin_lock_bh(&rdev->bss_lock);
 		if (cfg80211_add_nontrans_list(non_tx_data->tx_bss,
 					       &res->pub)) {
-			if (__cfg80211_unlink_bss(rdev, res))
+			if (__cfg80211_unlink_bss(rdev, res)) {
 				rdev->bss_generation++;
+				res = NULL;
+			}
 		}
+		spin_unlock_bh(&rdev->bss_lock);
+
+		if (!res)
+			return NULL;
 	}
 
 	trace_cfg80211_return_bss(&res->pub);
@@ -2094,6 +2230,8 @@
 	for_each_element_id(elem, WLAN_EID_MULTIPLE_BSSID, ie, ielen) {
 		if (elem->datalen < 4)
 			continue;
+		if (elem->data[0] < 1 || (int)elem->data[0] > 8)
+			continue;
 		for_each_element(sub, elem->data + 1, elem->datalen - 1) {
 			u8 profile_len;
 
@@ -2147,7 +2285,7 @@
 			new_ie_len = cfg80211_gen_new_ie(ie, ielen,
 							 profile,
 							 profile_len, new_ie,
-							 gfp);
+							 IEEE80211_MAX_DATA_LEN);
 			if (!new_ie_len)
 				continue;
 
@@ -2229,7 +2367,7 @@
 	size_t new_ie_len;
 	struct cfg80211_bss_ies *new_ies;
 	const struct cfg80211_bss_ies *old;
-	u8 cpy_len;
+	size_t cpy_len;
 
 	lockdep_assert_held(&wiphy_to_rdev(wiphy)->bss_lock);
 
@@ -2296,6 +2434,8 @@
 	} else {
 		old = rcu_access_pointer(nontrans_bss->beacon_ies);
 		rcu_assign_pointer(nontrans_bss->beacon_ies, new_ies);
+		cfg80211_update_hidden_bsses(bss_from_pub(nontrans_bss),
+					     new_ies, old);
 		rcu_assign_pointer(nontrans_bss->ies, new_ies);
 		if (old)
 			kfree_rcu((struct cfg80211_bss_ies *)old, rcu_head);
@@ -2442,10 +2582,15 @@
 	const struct cfg80211_bss_ies *ies1, *ies2;
 	size_t ielen = len - offsetof(struct ieee80211_mgmt,
 				      u.probe_resp.variable);
-	struct cfg80211_non_tx_bss non_tx_data;
+	struct cfg80211_non_tx_bss non_tx_data = {};
 
 	res = cfg80211_inform_single_bss_frame_data(wiphy, data, mgmt,
 						    len, gfp);
+
+	/* don't do any further MBSSID handling for S1G */
+	if (ieee80211_is_s1g_beacon(mgmt->frame_control))
+		return res;
+
 	if (!res || !wiphy->support_mbssid ||
 	    !cfg80211_find_ie(WLAN_EID_MULTIPLE_BSSID, ie, ielen))
 		return res;
@@ -2629,10 +2774,7 @@
 		if (!WARN_ON(!__cfg80211_unlink_bss(rdev, new)))
 			rdev->bss_generation++;
 	}
-
-	rb_erase(&cbss->rbn, &rdev->bss_tree);
-	rb_insert_bss(rdev, cbss);
-	rdev->bss_generation++;
+	cfg80211_rehash_bss(rdev, cbss);
 
 	list_for_each_entry_safe(nontrans_bss, tmp,
 				 &cbss->pub.nontrans_list,
@@ -2640,9 +2782,7 @@
 		bss = container_of(nontrans_bss,
 				   struct cfg80211_internal_bss, pub);
 		bss->pub.channel = chan;
-		rb_erase(&bss->rbn, &rdev->bss_tree);
-		rb_insert_bss(rdev, bss);
-		rdev->bss_generation++;
+		cfg80211_rehash_bss(rdev, bss);
 	}
 
 done:
@@ -2699,13 +2839,17 @@
 	wiphy = &rdev->wiphy;
 
 	/* Determine number of channels, needed to allocate creq */
-	if (wreq && wreq->num_channels)
+	if (wreq && wreq->num_channels) {
+		/* Passed from userspace so should be checked */
+		if (unlikely(wreq->num_channels > IW_MAX_FREQUENCIES))
+			return -EINVAL;
 		n_channels = wreq->num_channels;
-	else
+	} else {
 		n_channels = ieee80211_get_num_supported_channels(wiphy);
+	}
 
-	creq = kzalloc(sizeof(*creq) + sizeof(struct cfg80211_ssid) +
-		       n_channels * sizeof(void *),
+	creq = kzalloc(struct_size(creq, channels, n_channels) +
+		       sizeof(struct cfg80211_ssid),
 		       GFP_ATOMIC);
 	if (!creq) {
 		err = -ENOMEM;
@@ -2715,7 +2859,7 @@
 	creq->wiphy = wiphy;
 	creq->wdev = dev->ieee80211_ptr;
 	/* SSIDs come after channels */
-	creq->ssids = (void *)&creq->channels[n_channels];
+	creq->ssids = (void *)creq + struct_size(creq, channels, n_channels);
 	creq->n_channels = n_channels;
 	creq->n_ssids = 1;
 	creq->scan_start = jiffies;
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/sme.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/sme.c
@@ -115,7 +115,8 @@
 		n_channels = i;
 	}
 	request->n_channels = n_channels;
-	request->ssids = (void *)&request->channels[n_channels];
+	request->ssids = (void *)request +
+		struct_size(request, channels, n_channels);
 	request->n_ssids = 1;
 
 	memcpy(request->ssids[0].ssid, wdev->conn->params.ssid,
@@ -268,6 +269,15 @@
 	wiphy_unlock(&rdev->wiphy);
 }
 
+static void cfg80211_step_auth_next(struct cfg80211_conn *conn,
+				    struct cfg80211_bss *bss)
+{
+	memcpy(conn->bssid, bss->bssid, ETH_ALEN);
+	conn->params.bssid = conn->bssid;
+	conn->params.channel = bss->channel;
+	conn->state = CFG80211_CONN_AUTHENTICATE_NEXT;
+}
+
 /* Returned bss is reference counted and must be cleaned up appropriately. */
 static struct cfg80211_bss *cfg80211_get_conn_bss(struct wireless_dev *wdev)
 {
@@ -285,10 +295,7 @@
 	if (!bss)
 		return NULL;
 
-	memcpy(wdev->conn->bssid, bss->bssid, ETH_ALEN);
-	wdev->conn->params.bssid = wdev->conn->bssid;
-	wdev->conn->params.channel = bss->channel;
-	wdev->conn->state = CFG80211_CONN_AUTHENTICATE_NEXT;
+	cfg80211_step_auth_next(wdev->conn, bss);
 	schedule_work(&rdev->conn_work);
 
 	return bss;
@@ -567,7 +574,12 @@
 	wdev->conn->params.ssid_len = wdev->ssid_len;
 
 	/* see if we have the bss already */
-	bss = cfg80211_get_conn_bss(wdev);
+	bss = cfg80211_get_bss(wdev->wiphy, wdev->conn->params.channel,
+			       wdev->conn->params.bssid,
+			       wdev->conn->params.ssid,
+			       wdev->conn->params.ssid_len,
+			       wdev->conn_bss_type,
+			       IEEE80211_PRIVACY(wdev->conn->params.privacy));
 
 	if (prev_bssid) {
 		memcpy(wdev->conn->prev_bssid, prev_bssid, ETH_ALEN);
@@ -578,6 +590,7 @@
 	if (bss) {
 		enum nl80211_timeout_reason treason;
 
+		cfg80211_step_auth_next(wdev->conn, bss);
 		err = cfg80211_conn_do_work(wdev, &treason);
 		cfg80211_put_bss(wdev->wiphy, bss);
 	} else {
@@ -1244,6 +1257,13 @@
 	} else {
 		if (WARN_ON(connkeys))
 			return -EINVAL;
+
+		/* connect can point to wdev->wext.connect which
+		 * can hold key data from a previous connection
+		 */
+		connect->key = NULL;
+		connect->key_len = 0;
+		connect->key_idx = 0;
 	}
 
 	wdev->connect_keys = connkeys;
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/trace.h
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/trace.h
@@ -963,7 +963,7 @@
 TRACE_EVENT(rdev_dump_mpp,
 	TP_PROTO(struct wiphy *wiphy, struct net_device *netdev, int _idx,
 		 u8 *dst, u8 *mpp),
-	TP_ARGS(wiphy, netdev, _idx, mpp, dst),
+	TP_ARGS(wiphy, netdev, _idx, dst, mpp),
 	TP_STRUCT__entry(
 		WIPHY_ENTRY
 		NETDEV_ENTRY
@@ -1687,7 +1687,7 @@
 
 DECLARE_EVENT_CLASS(tx_rx_evt,
 	TP_PROTO(struct wiphy *wiphy, u32 tx, u32 rx),
-	TP_ARGS(wiphy, rx, tx),
+	TP_ARGS(wiphy, tx, rx),
 	TP_STRUCT__entry(
 		WIPHY_ENTRY
 		__field(u32, tx)
@@ -1704,7 +1704,7 @@
 
 DEFINE_EVENT(tx_rx_evt, rdev_set_antenna,
 	TP_PROTO(struct wiphy *wiphy, u32 tx, u32 rx),
-	TP_ARGS(wiphy, rx, tx)
+	TP_ARGS(wiphy, tx, rx)
 );
 
 DECLARE_EVENT_CLASS(wiphy_netdev_id_evt,
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/util.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/util.c
@@ -1044,6 +1044,7 @@
 
 		switch (otype) {
 		case NL80211_IFTYPE_AP:
+		case NL80211_IFTYPE_P2P_GO:
 			cfg80211_stop_ap(rdev, dev, true);
 			break;
 		case NL80211_IFTYPE_ADHOC:
@@ -1352,7 +1353,7 @@
 		 25599, /*  4.166666... */
 		 17067, /*  2.777777... */
 		 12801, /*  2.083333... */
-		 11769, /*  1.851851... */
+		 11377, /*  1.851725... */
 		 10239, /*  1.666666... */
 		  8532, /*  1.388888... */
 		  7680, /*  1.250000... */
@@ -1362,7 +1363,7 @@
 		  5120, /*  0.833333... */
 	};
 	u32 rates_160M[3] = { 960777777, 907400000, 816666666 };
-	u32 rates_969[3] =  { 480388888, 453700000, 408333333 };
+	u32 rates_996[3] =  { 480388888, 453700000, 408333333 };
 	u32 rates_484[3] =  { 229411111, 216666666, 195000000 };
 	u32 rates_242[3] =  { 114711111, 108333333,  97500000 };
 	u32 rates_106[3] =  {  40000000,  37777777,  34000000 };
@@ -1382,12 +1383,14 @@
 	if (WARN_ON_ONCE(rate->nss < 1 || rate->nss > 8))
 		return 0;
 
-	if (rate->bw == RATE_INFO_BW_160)
+	if (rate->bw == RATE_INFO_BW_160 ||
+	    (rate->bw == RATE_INFO_BW_HE_RU &&
+	     rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_2x996))
 		result = rates_160M[rate->he_gi];
 	else if (rate->bw == RATE_INFO_BW_80 ||
 		 (rate->bw == RATE_INFO_BW_HE_RU &&
 		  rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_996))
-		result = rates_969[rate->he_gi];
+		result = rates_996[rate->he_gi];
 	else if (rate->bw == RATE_INFO_BW_40 ||
 		 (rate->bw == RATE_INFO_BW_HE_RU &&
 		  rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_484))
@@ -2032,6 +2035,7 @@
 {
 	struct cfg80211_registered_device *rdev;
 	struct wireless_dev *wdev;
+	int ret;
 
 	wdev = dev->ieee80211_ptr;
 	if (!wdev)
@@ -2043,7 +2047,11 @@
 
 	memset(sinfo, 0, sizeof(*sinfo));
 
-	return rdev_get_station(rdev, dev, mac_addr, sinfo);
+	wiphy_lock(&rdev->wiphy);
+	ret = rdev_get_station(rdev, dev, mac_addr, sinfo);
+	wiphy_unlock(&rdev->wiphy);
+
+	return ret;
 }
 EXPORT_SYMBOL(cfg80211_get_station);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/wireless/wext-core.c
+++ linux-xilinx-zynqmp-5.15.0/net/wireless/wext-core.c
@@ -468,6 +468,7 @@
 	struct __compat_iw_event *compat_event;
 	struct compat_iw_point compat_wrqu;
 	struct sk_buff *compskb;
+	int ptr_len;
 #endif
 
 	/*
@@ -582,6 +583,9 @@
 	nlmsg_end(skb, nlh);
 #ifdef CONFIG_COMPAT
 	hdr_len = compat_event_type_size[descr->header_type];
+
+	/* ptr_len is remaining size in event header apart from LCP */
+	ptr_len = hdr_len - IW_EV_COMPAT_LCP_LEN;
 	event_len = hdr_len + extra_len;
 
 	compskb = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_ATOMIC);
@@ -612,16 +616,15 @@
 	if (descr->header_type == IW_HEADER_TYPE_POINT) {
 		compat_wrqu.length = wrqu->data.length;
 		compat_wrqu.flags = wrqu->data.flags;
-		memcpy(&compat_event->pointer,
-			((char *) &compat_wrqu) + IW_EV_COMPAT_POINT_OFF,
-			hdr_len - IW_EV_COMPAT_LCP_LEN);
+		memcpy(compat_event->ptr_bytes,
+		       ((char *)&compat_wrqu) + IW_EV_COMPAT_POINT_OFF,
+			ptr_len);
 		if (extra_len)
-			memcpy(((char *) compat_event) + hdr_len,
-				extra, extra_len);
+			memcpy(&compat_event->ptr_bytes[ptr_len],
+			       extra, extra_len);
 	} else {
 		/* extra_len must be zero, so no if (extra) needed */
-		memcpy(&compat_event->pointer, wrqu,
-			hdr_len - IW_EV_COMPAT_LCP_LEN);
+		memcpy(compat_event->ptr_bytes, wrqu, ptr_len);
 	}
 
 	nlmsg_end(compskb, nlh);
@@ -796,6 +799,12 @@
 		}
 	}
 
+	/* Sanity-check to ensure we never end up _allocating_ zero
+	 * bytes of data for extra.
+	 */
+	if (extra_size <= 0)
+		return -EFAULT;
+
 	/* kzalloc() ensures NULL-termination for essid_compat. */
 	extra = kzalloc(extra_size, GFP_KERNEL);
 	if (!extra)
--- linux-xilinx-zynqmp-5.15.0.orig/net/x25/af_x25.c
+++ linux-xilinx-zynqmp-5.15.0/net/x25/af_x25.c
@@ -460,12 +460,12 @@
 	if (get_user(len, optlen))
 		goto out;
 
-	len = min_t(unsigned int, len, sizeof(int));
-
 	rc = -EINVAL;
 	if (len < 0)
 		goto out;
 
+	len = min_t(unsigned int, len, sizeof(int));
+
 	rc = -EFAULT;
 	if (put_user(len, optlen))
 		goto out;
@@ -482,6 +482,12 @@
 	int rc = -EOPNOTSUPP;
 
 	lock_sock(sk);
+	if (sock->state != SS_UNCONNECTED) {
+		rc = -EINVAL;
+		release_sock(sk);
+		return rc;
+	}
+
 	if (sk->sk_state != TCP_LISTEN) {
 		memset(&x25_sk(sk)->dest_addr, 0, X25_ADDR_LEN);
 		sk->sk_max_ack_backlog = backlog;
@@ -1765,10 +1771,15 @@
 
 	write_lock_bh(&x25_list_lock);
 
-	sk_for_each(s, &x25_list)
-		if (x25_sk(s)->neighbour == nb)
+	sk_for_each(s, &x25_list) {
+		if (x25_sk(s)->neighbour == nb) {
+			write_unlock_bh(&x25_list_lock);
+			lock_sock(s);
 			x25_disconnect(s, ENETUNREACH, 0, 0);
-
+			release_sock(s);
+			write_lock_bh(&x25_list_lock);
+		}
+	}
 	write_unlock_bh(&x25_list_lock);
 
 	/* Remove any related forwards */
--- linux-xilinx-zynqmp-5.15.0.orig/net/x25/x25_dev.c
+++ linux-xilinx-zynqmp-5.15.0/net/x25/x25_dev.c
@@ -117,7 +117,7 @@
 
 	if (!pskb_may_pull(skb, 1)) {
 		x25_neigh_put(nb);
-		return 0;
+		goto drop;
 	}
 
 	switch (skb->data[0]) {
--- linux-xilinx-zynqmp-5.15.0.orig/net/xdp/xdp_umem.c
+++ linux-xilinx-zynqmp-5.15.0/net/xdp/xdp_umem.c
@@ -152,10 +152,11 @@
 
 static int xdp_umem_reg(struct xdp_umem *umem, struct xdp_umem_reg *mr)
 {
-	u32 npgs_rem, chunk_size = mr->chunk_size, headroom = mr->headroom;
 	bool unaligned_chunks = mr->flags & XDP_UMEM_UNALIGNED_CHUNK_FLAG;
-	u64 npgs, addr = mr->addr, size = mr->len;
-	unsigned int chunks, chunks_rem;
+	u32 chunk_size = mr->chunk_size, headroom = mr->headroom;
+	u64 addr = mr->addr, size = mr->len;
+	u32 chunks_rem, npgs_rem;
+	u64 chunks, npgs;
 	int err;
 
 	if (chunk_size < XDP_UMEM_MIN_CHUNK_SIZE || chunk_size > PAGE_SIZE) {
@@ -190,8 +191,8 @@
 	if (npgs > U32_MAX)
 		return -EINVAL;
 
-	chunks = (unsigned int)div_u64_rem(size, chunk_size, &chunks_rem);
-	if (chunks == 0)
+	chunks = div_u64_rem(size, chunk_size, &chunks_rem);
+	if (!chunks || chunks > U32_MAX)
 		return -EINVAL;
 
 	if (!unaligned_chunks && chunks_rem)
@@ -204,7 +205,7 @@
 	umem->headroom = headroom;
 	umem->chunk_size = chunk_size;
 	umem->chunks = chunks;
-	umem->npgs = (u32)npgs;
+	umem->npgs = npgs;
 	umem->pgs = NULL;
 	umem->user = NULL;
 	umem->flags = mr->flags;
--- linux-xilinx-zynqmp-5.15.0.orig/net/xdp/xsk.c
+++ linux-xilinx-zynqmp-5.15.0/net/xdp/xsk.c
@@ -358,9 +358,9 @@
 }
 EXPORT_SYMBOL(xsk_tx_peek_desc);
 
-static u32 xsk_tx_peek_release_fallback(struct xsk_buff_pool *pool, struct xdp_desc *descs,
-					u32 max_entries)
+static u32 xsk_tx_peek_release_fallback(struct xsk_buff_pool *pool, u32 max_entries)
 {
+	struct xdp_desc *descs = pool->tx_descs;
 	u32 nb_pkts = 0;
 
 	while (nb_pkts < max_entries && xsk_tx_peek_desc(pool, &descs[nb_pkts]))
@@ -370,17 +370,15 @@
 	return nb_pkts;
 }
 
-u32 xsk_tx_peek_release_desc_batch(struct xsk_buff_pool *pool, struct xdp_desc *descs,
-				   u32 max_entries)
+u32 xsk_tx_peek_release_desc_batch(struct xsk_buff_pool *pool, u32 nb_pkts)
 {
 	struct xdp_sock *xs;
-	u32 nb_pkts;
 
 	rcu_read_lock();
 	if (!list_is_singular(&pool->xsk_tx_list)) {
 		/* Fallback to the non-batched version */
 		rcu_read_unlock();
-		return xsk_tx_peek_release_fallback(pool, descs, max_entries);
+		return xsk_tx_peek_release_fallback(pool, nb_pkts);
 	}
 
 	xs = list_first_or_null_rcu(&pool->xsk_tx_list, struct xdp_sock, tx_list);
@@ -389,11 +387,7 @@
 		goto out;
 	}
 
-	nb_pkts = xskq_cons_peek_desc_batch(xs->tx, descs, pool, max_entries);
-	if (!nb_pkts) {
-		xs->tx->queue_empty_descs++;
-		goto out;
-	}
+	nb_pkts = xskq_cons_nb_entries(xs->tx, nb_pkts);
 
 	/* This is the backpressure mechanism for the Tx path. Try to
 	 * reserve space in the completion queue for all packets, but
@@ -401,12 +395,18 @@
 	 * packets. This avoids having to implement any buffering in
 	 * the Tx path.
 	 */
-	nb_pkts = xskq_prod_reserve_addr_batch(pool->cq, descs, nb_pkts);
+	nb_pkts = xskq_prod_nb_free(pool->cq, nb_pkts);
 	if (!nb_pkts)
 		goto out;
 
-	xskq_cons_release_n(xs->tx, nb_pkts);
+	nb_pkts = xskq_cons_read_desc_batch(xs->tx, pool, nb_pkts);
+	if (!nb_pkts) {
+		xs->tx->queue_empty_descs++;
+		goto out;
+	}
+
 	__xskq_cons_release(xs->tx);
+	xskq_prod_write_addr_batch(pool->cq, pool->tx_descs, nb_pkts);
 	xs->sk.sk_write_space(&xs->sk);
 
 out:
@@ -418,18 +418,8 @@
 static int xsk_wakeup(struct xdp_sock *xs, u8 flags)
 {
 	struct net_device *dev = xs->dev;
-	int err;
 
-	rcu_read_lock();
-	err = dev->netdev_ops->ndo_xsk_wakeup(dev, xs->queue_id, flags);
-	rcu_read_unlock();
-
-	return err;
-}
-
-static int xsk_zc_xmit(struct xdp_sock *xs)
-{
-	return xsk_wakeup(xs, XDP_WAKEUP_TX);
+	return dev->netdev_ops->ndo_xsk_wakeup(dev, xs->queue_id, flags);
 }
 
 static void xsk_destruct_skb(struct sk_buff *skb)
@@ -548,6 +538,12 @@
 
 	mutex_lock(&xs->mutex);
 
+	/* Since we dropped the RCU read lock, the socket state might have changed. */
+	if (unlikely(!xsk_is_bound(xs))) {
+		err = -ENXIO;
+		goto out;
+	}
+
 	if (xs->queue_id >= xs->dev->real_num_tx_queues)
 		goto out;
 
@@ -557,12 +553,6 @@
 			goto out;
 		}
 
-		skb = xsk_build_skb(xs, &desc);
-		if (IS_ERR(skb)) {
-			err = PTR_ERR(skb);
-			goto out;
-		}
-
 		/* This is the backpressure mechanism for the Tx path.
 		 * Reserve space in the completion queue and only proceed
 		 * if there is space in it. This avoids having to implement
@@ -571,11 +561,19 @@
 		spin_lock_irqsave(&xs->pool->cq_lock, flags);
 		if (xskq_prod_reserve(xs->pool->cq)) {
 			spin_unlock_irqrestore(&xs->pool->cq_lock, flags);
-			kfree_skb(skb);
 			goto out;
 		}
 		spin_unlock_irqrestore(&xs->pool->cq_lock, flags);
 
+		skb = xsk_build_skb(xs, &desc);
+		if (IS_ERR(skb)) {
+			err = PTR_ERR(skb);
+			spin_lock_irqsave(&xs->pool->cq_lock, flags);
+			xskq_prod_cancel(xs->pool->cq);
+			spin_unlock_irqrestore(&xs->pool->cq_lock, flags);
+			goto out;
+		}
+
 		err = __dev_direct_xmit(skb, xs->queue_id);
 		if  (err == NETDEV_TX_BUSY) {
 			/* Tell user-space to retry the send */
@@ -611,16 +609,26 @@
 	return err;
 }
 
-static int __xsk_sendmsg(struct sock *sk)
+static int xsk_xmit(struct sock *sk)
 {
 	struct xdp_sock *xs = xdp_sk(sk);
+	int ret;
 
 	if (unlikely(!(xs->dev->flags & IFF_UP)))
 		return -ENETDOWN;
 	if (unlikely(!xs->tx))
 		return -ENOBUFS;
 
-	return xs->zc ? xsk_zc_xmit(xs) : xsk_generic_xmit(sk);
+	if (xs->zc)
+		return xsk_wakeup(xs, XDP_WAKEUP_TX);
+
+	/* Drop the RCU lock since the SKB path might sleep. */
+	rcu_read_unlock();
+	ret = xsk_generic_xmit(sk);
+	/* Reaquire RCU lock before going into common code. */
+	rcu_read_lock();
+
+	return ret;
 }
 
 static bool xsk_no_wakeup(struct sock *sk)
@@ -634,7 +642,7 @@
 #endif
 }
 
-static int xsk_sendmsg(struct socket *sock, struct msghdr *m, size_t total_len)
+static int __xsk_sendmsg(struct socket *sock, struct msghdr *m, size_t total_len)
 {
 	bool need_wait = !(m->msg_flags & MSG_DONTWAIT);
 	struct sock *sk = sock->sk;
@@ -649,16 +657,27 @@
 	if (sk_can_busy_loop(sk))
 		sk_busy_loop(sk, 1); /* only support non-blocking sockets */
 
-	if (xsk_no_wakeup(sk))
+	if (xs->zc && xsk_no_wakeup(sk))
 		return 0;
 
 	pool = xs->pool;
 	if (pool->cached_need_wakeup & XDP_WAKEUP_TX)
-		return __xsk_sendmsg(sk);
+		return xsk_xmit(sk);
 	return 0;
 }
 
-static int xsk_recvmsg(struct socket *sock, struct msghdr *m, size_t len, int flags)
+static int xsk_sendmsg(struct socket *sock, struct msghdr *m, size_t total_len)
+{
+	int ret;
+
+	rcu_read_lock();
+	ret = __xsk_sendmsg(sock, m, total_len);
+	rcu_read_unlock();
+
+	return ret;
+}
+
+static int __xsk_recvmsg(struct socket *sock, struct msghdr *m, size_t len, int flags)
 {
 	bool need_wait = !(flags & MSG_DONTWAIT);
 	struct sock *sk = sock->sk;
@@ -684,6 +703,17 @@
 	return 0;
 }
 
+static int xsk_recvmsg(struct socket *sock, struct msghdr *m, size_t len, int flags)
+{
+	int ret;
+
+	rcu_read_lock();
+	ret = __xsk_recvmsg(sock, m, len, flags);
+	rcu_read_unlock();
+
+	return ret;
+}
+
 static __poll_t xsk_poll(struct file *file, struct socket *sock,
 			     struct poll_table_struct *wait)
 {
@@ -694,8 +724,11 @@
 
 	sock_poll_wait(file, sock, wait);
 
-	if (unlikely(!xsk_is_bound(xs)))
+	rcu_read_lock();
+	if (unlikely(!xsk_is_bound(xs))) {
+		rcu_read_unlock();
 		return mask;
+	}
 
 	pool = xs->pool;
 
@@ -704,7 +737,7 @@
 			xsk_wakeup(xs, pool->cached_need_wakeup);
 		else
 			/* Poll needs to drive Tx also in copy mode */
-			__xsk_sendmsg(sk);
+			xsk_xmit(sk);
 	}
 
 	if (xs->rx && !xskq_prod_is_empty(xs->rx))
@@ -712,6 +745,7 @@
 	if (xs->tx && xsk_tx_writeable(xs))
 		mask |= EPOLLOUT | EPOLLWRNORM;
 
+	rcu_read_unlock();
 	return mask;
 }
 
@@ -743,7 +777,6 @@
 
 	/* Wait for driver to stop using the xdp socket. */
 	xp_del_xsk(xs->pool, xs);
-	xs->dev = NULL;
 	synchronize_net();
 	dev_put(dev);
 }
@@ -809,9 +842,7 @@
 	sk_del_node_init_rcu(sk);
 	mutex_unlock(&net->xdp.lock);
 
-	local_bh_disable();
 	sock_prot_inuse_add(net, sk->sk_prot, -1);
-	local_bh_enable();
 
 	xsk_delete_from_maps(xs);
 	mutex_lock(&xs->mutex);
@@ -860,6 +891,7 @@
 	struct sock *sk = sock->sk;
 	struct xdp_sock *xs = xdp_sk(sk);
 	struct net_device *dev;
+	int bound_dev_if;
 	u32 flags, qid;
 	int err = 0;
 
@@ -873,6 +905,10 @@
 		      XDP_USE_NEED_WAKEUP))
 		return -EINVAL;
 
+	bound_dev_if = READ_ONCE(sk->sk_bound_dev_if);
+	if (bound_dev_if && bound_dev_if != sxdp->sxdp_ifindex)
+		return -EINVAL;
+
 	rtnl_lock();
 	mutex_lock(&xs->mutex);
 	if (xs->state != XSK_READY) {
@@ -935,8 +971,8 @@
 				goto out_unlock;
 			}
 
-			err = xp_assign_dev_shared(xs->pool, umem_xs->umem,
-						   dev, qid);
+			err = xp_assign_dev_shared(xs->pool, umem_xs, dev,
+						   qid);
 			if (err) {
 				xp_destroy(xs->pool);
 				xs->pool = NULL;
@@ -954,6 +990,20 @@
 
 			xp_get_pool(umem_xs->pool);
 			xs->pool = umem_xs->pool;
+
+			/* If underlying shared umem was created without Tx
+			 * ring, allocate Tx descs array that Tx batching API
+			 * utilizes
+			 */
+			if (xs->tx && !xs->pool->tx_descs) {
+				err = xp_alloc_tx_descs(xs->pool, xs);
+				if (err) {
+					xp_put_pool(xs->pool);
+					xs->pool = NULL;
+					sockfd_put(sock);
+					goto out_unlock;
+				}
+			}
 		}
 
 		xdp_get_umem(umem_xs->umem);
@@ -1083,6 +1133,8 @@
 		struct xsk_queue **q;
 		int entries;
 
+		if (optlen < sizeof(entries))
+			return -EINVAL;
 		if (copy_from_sockptr(&entries, optval, sizeof(entries)))
 			return -EFAULT;
 
@@ -1411,9 +1463,7 @@
 	sk_add_node_rcu(sk, &net->xdp.list);
 	mutex_unlock(&net->xdp.lock);
 
-	local_bh_disable();
 	sock_prot_inuse_add(net, &xsk_proto, 1);
-	local_bh_enable();
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/xdp/xsk_buff_pool.c
+++ linux-xilinx-zynqmp-5.15.0/net/xdp/xsk_buff_pool.c
@@ -37,10 +37,21 @@
 	if (!pool)
 		return;
 
+	kvfree(pool->tx_descs);
 	kvfree(pool->heads);
 	kvfree(pool);
 }
 
+int xp_alloc_tx_descs(struct xsk_buff_pool *pool, struct xdp_sock *xs)
+{
+	pool->tx_descs = kvcalloc(xs->tx->nentries, sizeof(*pool->tx_descs),
+				  GFP_KERNEL);
+	if (!pool->tx_descs)
+		return -ENOMEM;
+
+	return 0;
+}
+
 struct xsk_buff_pool *xp_create_and_assign_umem(struct xdp_sock *xs,
 						struct xdp_umem *umem)
 {
@@ -57,6 +68,10 @@
 	if (!pool->heads)
 		goto out;
 
+	if (xs->tx)
+		if (xp_alloc_tx_descs(pool, xs))
+			goto out;
+
 	pool->chunk_mask = ~((u64)umem->chunk_size - 1);
 	pool->addrs_cnt = umem->size;
 	pool->heads_cnt = umem->chunks;
@@ -191,17 +206,18 @@
 	return err;
 }
 
-int xp_assign_dev_shared(struct xsk_buff_pool *pool, struct xdp_umem *umem,
+int xp_assign_dev_shared(struct xsk_buff_pool *pool, struct xdp_sock *umem_xs,
 			 struct net_device *dev, u16 queue_id)
 {
 	u16 flags;
+	struct xdp_umem *umem = umem_xs->umem;
 
 	/* One fill and completion ring required for each queue id. */
 	if (!pool->fq || !pool->cq)
 		return -EINVAL;
 
 	flags = umem->zc ? XDP_ZEROCOPY : XDP_COPY;
-	if (pool->uses_need_wakeup)
+	if (umem_xs->pool->uses_need_wakeup)
 		flags |= XDP_USE_NEED_WAKEUP;
 
 	return xp_assign_dev(pool, dev, queue_id, flags);
@@ -311,6 +327,7 @@
 	for (i = 0; i < dma_map->dma_pages_cnt; i++) {
 		dma = &dma_map->dma_pages[i];
 		if (*dma) {
+			*dma &= ~XSK_NEXT_PG_CONTIG_MASK;
 			dma_unmap_page_attrs(dma_map->dev, *dma, PAGE_SIZE,
 					     DMA_BIDIRECTIONAL, attrs);
 			*dma = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/net/xdp/xsk_diag.c
+++ linux-xilinx-zynqmp-5.15.0/net/xdp/xsk_diag.c
@@ -111,6 +111,9 @@
 	sock_diag_save_cookie(sk, msg->xdiag_cookie);
 
 	mutex_lock(&xs->mutex);
+	if (READ_ONCE(xs->state) == XSK_UNBOUND)
+		goto out_nlmsg_trim;
+
 	if ((req->xdiag_show & XDP_SHOW_INFO) && xsk_diag_put_info(xs, nlskb))
 		goto out_nlmsg_trim;
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/xdp/xsk_queue.h
+++ linux-xilinx-zynqmp-5.15.0/net/xdp/xsk_queue.h
@@ -157,6 +157,7 @@
 		return false;
 
 	if (base_addr >= pool->addrs_cnt || addr >= pool->addrs_cnt ||
+	    addr + desc->len > pool->addrs_cnt ||
 	    xp_desc_crosses_non_contig_pg(pool, addr, desc->len))
 		return false;
 
@@ -201,11 +202,16 @@
 	return false;
 }
 
-static inline u32 xskq_cons_read_desc_batch(struct xsk_queue *q,
-					    struct xdp_desc *descs,
-					    struct xsk_buff_pool *pool, u32 max)
+static inline void xskq_cons_release_n(struct xsk_queue *q, u32 cnt)
+{
+	q->cached_cons += cnt;
+}
+
+static inline u32 xskq_cons_read_desc_batch(struct xsk_queue *q, struct xsk_buff_pool *pool,
+					    u32 max)
 {
 	u32 cached_cons = q->cached_cons, nb_entries = 0;
+	struct xdp_desc *descs = pool->tx_descs;
 
 	while (cached_cons != q->cached_prod && nb_entries < max) {
 		struct xdp_rxtx_ring *ring = (struct xdp_rxtx_ring *)q->ring;
@@ -222,6 +228,8 @@
 		cached_cons++;
 	}
 
+	/* Release valid plus any invalid entries */
+	xskq_cons_release_n(q, cached_cons - q->cached_cons);
 	return nb_entries;
 }
 
@@ -278,14 +286,6 @@
 	return xskq_cons_read_desc(q, desc, pool);
 }
 
-static inline u32 xskq_cons_peek_desc_batch(struct xsk_queue *q, struct xdp_desc *descs,
-					    struct xsk_buff_pool *pool, u32 max)
-{
-	u32 entries = xskq_cons_nb_entries(q, max);
-
-	return xskq_cons_read_desc_batch(q, descs, pool, entries);
-}
-
 /* To improve performance in the xskq_cons_release functions, only update local state here.
  * Reflect this to global state when we get new entries from the ring in
  * xskq_cons_get_entries() and whenever Rx or Tx processing are completed in the NAPI loop.
@@ -295,11 +295,6 @@
 	q->cached_cons++;
 }
 
-static inline void xskq_cons_release_n(struct xsk_queue *q, u32 cnt)
-{
-	q->cached_cons += cnt;
-}
-
 static inline bool xskq_cons_is_full(struct xsk_queue *q)
 {
 	/* No barriers needed since data is not accessed */
@@ -361,21 +356,17 @@
 	return 0;
 }
 
-static inline u32 xskq_prod_reserve_addr_batch(struct xsk_queue *q, struct xdp_desc *descs,
-					       u32 max)
+static inline void xskq_prod_write_addr_batch(struct xsk_queue *q, struct xdp_desc *descs,
+					      u32 nb_entries)
 {
 	struct xdp_umem_ring *ring = (struct xdp_umem_ring *)q->ring;
-	u32 nb_entries, i, cached_prod;
-
-	nb_entries = xskq_prod_nb_free(q, max);
+	u32 i, cached_prod;
 
 	/* A, matches D */
 	cached_prod = q->cached_prod;
 	for (i = 0; i < nb_entries; i++)
 		ring->desc[cached_prod++ & q->ring_mask] = descs[i].addr;
 	q->cached_prod = cached_prod;
-
-	return nb_entries;
 }
 
 static inline int xskq_prod_reserve_desc(struct xsk_queue *q,
--- linux-xilinx-zynqmp-5.15.0.orig/net/xdp/xskmap.c
+++ linux-xilinx-zynqmp-5.15.0/net/xdp/xskmap.c
@@ -214,7 +214,7 @@
 	struct xsk_map *m = container_of(map, struct xsk_map, map);
 	struct xdp_sock __rcu **map_entry;
 	struct xdp_sock *old_xs;
-	int k = *(u32 *)key;
+	u32 k = *(u32 *)key;
 
 	if (k >= map->max_entries)
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/Makefile
@@ -3,6 +3,8 @@
 # Makefile for the XFRM subsystem.
 #
 
+xfrm_interface-$(CONFIG_XFRM_INTERFACE) += xfrm_interface_core.o
+
 obj-$(CONFIG_XFRM) := xfrm_policy.o xfrm_state.o xfrm_hash.o \
 		      xfrm_input.o xfrm_output.o \
 		      xfrm_sysctl.o xfrm_replay.o xfrm_device.o
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/espintcp.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/espintcp.c
@@ -170,7 +170,7 @@
 {
 	struct espintcp_ctx *ctx = espintcp_getctx(sk);
 
-	if (skb_queue_len(&ctx->out_queue) >= netdev_max_backlog)
+	if (skb_queue_len(&ctx->out_queue) >= READ_ONCE(netdev_max_backlog))
 		return -ENOBUFS;
 
 	__skb_queue_tail(&ctx->out_queue, skb);
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_compat.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_compat.c
@@ -5,6 +5,7 @@
  * Based on code and translator idea by: Florian Westphal <fw@strlen.de>
  */
 #include <linux/compat.h>
+#include <linux/nospec.h>
 #include <linux/xfrm.h>
 #include <net/xfrm.h>
 
@@ -107,7 +108,7 @@
 	[XFRMA_ALG_COMP]	= { .len = sizeof(struct xfrm_algo) },
 	[XFRMA_ENCAP]		= { .len = sizeof(struct xfrm_encap_tmpl) },
 	[XFRMA_TMPL]		= { .len = sizeof(struct xfrm_user_tmpl) },
-	[XFRMA_SEC_CTX]		= { .len = sizeof(struct xfrm_sec_ctx) },
+	[XFRMA_SEC_CTX]		= { .len = sizeof(struct xfrm_user_sec_ctx) },
 	[XFRMA_LTIME_VAL]	= { .len = sizeof(struct xfrm_lifetime_cur) },
 	[XFRMA_REPLAY_VAL]	= { .len = sizeof(struct xfrm_replay_state) },
 	[XFRMA_REPLAY_THRESH]	= { .type = NLA_U32 },
@@ -127,6 +128,7 @@
 	[XFRMA_SET_MARK]	= { .type = NLA_U32 },
 	[XFRMA_SET_MARK_MASK]	= { .type = NLA_U32 },
 	[XFRMA_IF_ID]		= { .type = NLA_U32 },
+	[XFRMA_MTIMER_THRESH]	= { .type = NLA_U32 },
 };
 
 static struct nlmsghdr *xfrm_nlmsg_put_compat(struct sk_buff *skb,
@@ -274,9 +276,10 @@
 	case XFRMA_SET_MARK:
 	case XFRMA_SET_MARK_MASK:
 	case XFRMA_IF_ID:
+	case XFRMA_MTIMER_THRESH:
 		return xfrm_nla_cpy(dst, src, nla_len(src));
 	default:
-		BUILD_BUG_ON(XFRMA_MAX != XFRMA_IF_ID);
+		BUILD_BUG_ON(XFRMA_MAX != XFRMA_MTIMER_THRESH);
 		pr_warn_once("unsupported nla_type %d\n", src->nla_type);
 		return -EOPNOTSUPP;
 	}
@@ -300,7 +303,7 @@
 	nla_for_each_attr(nla, attrs, len, remaining) {
 		int err;
 
-		switch (type) {
+		switch (nlh_src->nlmsg_type) {
 		case XFRM_MSG_NEWSPDINFO:
 			err = xfrm_nla_cpy(dst, nla, nla_len(nla));
 			break;
@@ -431,10 +434,11 @@
 	int err;
 
 	if (type > XFRMA_MAX) {
-		BUILD_BUG_ON(XFRMA_MAX != XFRMA_IF_ID);
+		BUILD_BUG_ON(XFRMA_MAX != XFRMA_MTIMER_THRESH);
 		NL_SET_ERR_MSG(extack, "Bad attribute");
 		return -EOPNOTSUPP;
 	}
+	type = array_index_nospec(type, XFRMA_MAX + 1);
 	if (nla_len(nla) < compat_policy[type].len) {
 		NL_SET_ERR_MSG(extack, "Attribute bad length");
 		return -EOPNOTSUPP;
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_device.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_device.c
@@ -97,6 +97,18 @@
 	}
 }
 
+static inline bool xmit_xfrm_check_overflow(struct sk_buff *skb)
+{
+	struct xfrm_offload *xo = xfrm_offload(skb);
+	__u32 seq = xo->seq.low;
+
+	seq += skb_shinfo(skb)->gso_segs;
+	if (unlikely(seq < xo->seq.low))
+		return true;
+
+	return false;
+}
+
 struct sk_buff *validate_xmit_xfrm(struct sk_buff *skb, netdev_features_t features, bool *again)
 {
 	int err;
@@ -117,7 +129,7 @@
 
 	sp = skb_sec_path(skb);
 	x = sp->xvec[sp->len - 1];
-	if (xo->flags & XFRM_GRO || x->xso.flags & XFRM_OFFLOAD_INBOUND)
+	if (xo->flags & XFRM_GRO || x->xso.dir == XFRM_DEV_OFFLOAD_IN)
 		return skb;
 
 	/* This skb was already validated on the upper/virtual dev */
@@ -134,7 +146,8 @@
 		return skb;
 	}
 
-	if (skb_is_gso(skb) && unlikely(x->xso.dev != dev)) {
+	if (skb_is_gso(skb) && (unlikely(x->xso.dev != dev) ||
+				unlikely(xmit_xfrm_check_overflow(skb)))) {
 		struct sk_buff *segs;
 
 		/* Packet got rerouted, fixup features and segment it. */
@@ -212,7 +225,7 @@
 	int err;
 	struct dst_entry *dst;
 	struct net_device *dev;
-	struct xfrm_state_offload *xso = &x->xso;
+	struct xfrm_dev_offload *xso = &x->xso;
 	xfrm_address_t *saddr;
 	xfrm_address_t *daddr;
 
@@ -223,8 +236,13 @@
 	if (x->encap || x->tfcpad)
 		return -EINVAL;
 
+	if (xuo->flags & ~(XFRM_OFFLOAD_IPV6 | XFRM_OFFLOAD_INBOUND))
+		return -EINVAL;
+
 	dev = dev_get_by_index(net, xuo->ifindex);
 	if (!dev) {
+		struct xfrm_dst_lookup_params params;
+
 		if (!(xuo->flags & XFRM_OFFLOAD_INBOUND)) {
 			saddr = &x->props.saddr;
 			daddr = &x->id.daddr;
@@ -233,9 +251,12 @@
 			daddr = &x->props.saddr;
 		}
 
-		dst = __xfrm_dst_lookup(net, 0, 0, saddr, daddr,
-					x->props.family,
-					xfrm_smark_get(0, x));
+		memset(&params, 0, sizeof(params));
+		params.net = net;
+		params.saddr = saddr;
+		params.daddr = daddr;
+		params.mark = xfrm_smark_get(0, x);
+		dst = __xfrm_dst_lookup(x->props.family, &params);
 		if (IS_ERR(dst))
 			return 0;
 
@@ -261,13 +282,20 @@
 	xso->dev = dev;
 	xso->real_dev = dev;
 	xso->num_exthdrs = 1;
-	xso->flags = xuo->flags;
+	/* Don't forward bit that is not implemented */
+	xso->flags = xuo->flags & ~XFRM_OFFLOAD_IPV6;
+
+	if (xuo->flags & XFRM_OFFLOAD_INBOUND)
+		xso->dir = XFRM_DEV_OFFLOAD_IN;
+	else
+		xso->dir = XFRM_DEV_OFFLOAD_OUT;
 
 	err = dev->xfrmdev_ops->xdo_dev_state_add(x);
 	if (err) {
 		xso->num_exthdrs = 0;
 		xso->flags = 0;
 		xso->dev = NULL;
+		xso->dir = 0;
 		xso->real_dev = NULL;
 		dev_put(dev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_input.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_input.c
@@ -24,7 +24,8 @@
 #include "xfrm_inout.h"
 
 struct xfrm_trans_tasklet {
-	struct tasklet_struct tasklet;
+	struct work_struct work;
+	spinlock_t queue_lock;
 	struct sk_buff_head queue;
 };
 
@@ -129,6 +130,7 @@
 	memset(sp->ovec, 0, sizeof(sp->ovec));
 	sp->olen = 0;
 	sp->len = 0;
+	sp->verified_cnt = 0;
 
 	return sp;
 }
@@ -277,8 +279,7 @@
 		goto out;
 
 	if (x->props.flags & XFRM_STATE_DECAP_DSCP)
-		ipv6_copy_dscp(ipv6_get_dsfield(ipv6_hdr(skb)),
-			       ipipv6_hdr(skb));
+		ipv6_copy_dscp(XFRM_MODE_SKB_CB(skb)->tos, ipipv6_hdr(skb));
 	if (!(x->props.flags & XFRM_STATE_NOECN))
 		ipip6_ecn_decapsulate(skb);
 
@@ -399,11 +400,15 @@
  */
 static int xfrm4_transport_input(struct xfrm_state *x, struct sk_buff *skb)
 {
+	struct xfrm_offload *xo = xfrm_offload(skb);
 	int ihl = skb->data - skb_transport_header(skb);
 
 	if (skb->transport_header != skb->network_header) {
 		memmove(skb_transport_header(skb),
 			skb_network_header(skb), ihl);
+		if (xo)
+			xo->orig_mac_len =
+				skb_mac_header_was_set(skb) ? skb_mac_header_len(skb) : 0;
 		skb->network_header = skb->transport_header;
 	}
 	ip_hdr(skb)->tot_len = htons(skb->len + ihl);
@@ -414,11 +419,15 @@
 static int xfrm6_transport_input(struct xfrm_state *x, struct sk_buff *skb)
 {
 #if IS_ENABLED(CONFIG_IPV6)
+	struct xfrm_offload *xo = xfrm_offload(skb);
 	int ihl = skb->data - skb_transport_header(skb);
 
 	if (skb->transport_header != skb->network_header) {
 		memmove(skb_transport_header(skb),
 			skb_network_header(skb), ihl);
+		if (xo)
+			xo->orig_mac_len =
+				skb_mac_header_was_set(skb) ? skb_mac_header_len(skb) : 0;
 		skb->network_header = skb->transport_header;
 	}
 	ipv6_hdr(skb)->payload_len = htons(skb->len + ihl -
@@ -760,18 +769,22 @@
 }
 EXPORT_SYMBOL(xfrm_input_resume);
 
-static void xfrm_trans_reinject(struct tasklet_struct *t)
+static void xfrm_trans_reinject(struct work_struct *work)
 {
-	struct xfrm_trans_tasklet *trans = from_tasklet(trans, t, tasklet);
+	struct xfrm_trans_tasklet *trans = container_of(work, struct xfrm_trans_tasklet, work);
 	struct sk_buff_head queue;
 	struct sk_buff *skb;
 
 	__skb_queue_head_init(&queue);
+	spin_lock_bh(&trans->queue_lock);
 	skb_queue_splice_init(&trans->queue, &queue);
+	spin_unlock_bh(&trans->queue_lock);
 
+	local_bh_disable();
 	while ((skb = __skb_dequeue(&queue)))
 		XFRM_TRANS_SKB_CB(skb)->finish(XFRM_TRANS_SKB_CB(skb)->net,
 					       NULL, skb);
+	local_bh_enable();
 }
 
 int xfrm_trans_queue_net(struct net *net, struct sk_buff *skb,
@@ -782,15 +795,17 @@
 
 	trans = this_cpu_ptr(&xfrm_trans_tasklet);
 
-	if (skb_queue_len(&trans->queue) >= netdev_max_backlog)
+	if (skb_queue_len(&trans->queue) >= READ_ONCE(netdev_max_backlog))
 		return -ENOBUFS;
 
 	BUILD_BUG_ON(sizeof(struct xfrm_trans_cb) > sizeof(skb->cb));
 
 	XFRM_TRANS_SKB_CB(skb)->finish = finish;
 	XFRM_TRANS_SKB_CB(skb)->net = net;
+	spin_lock_bh(&trans->queue_lock);
 	__skb_queue_tail(&trans->queue, skb);
-	tasklet_schedule(&trans->tasklet);
+	spin_unlock_bh(&trans->queue_lock);
+	schedule_work(&trans->work);
 	return 0;
 }
 EXPORT_SYMBOL(xfrm_trans_queue_net);
@@ -817,7 +832,8 @@
 		struct xfrm_trans_tasklet *trans;
 
 		trans = &per_cpu(xfrm_trans_tasklet, i);
+		spin_lock_init(&trans->queue_lock);
 		__skb_queue_head_init(&trans->queue);
-		tasklet_setup(&trans->tasklet, xfrm_trans_reinject);
+		INIT_WORK(&trans->work, xfrm_trans_reinject);
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_interface_core.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_interface_core.c
@@ -0,0 +1,1076 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *	XFRM virtual interface
+ *
+ *	Copyright (C) 2018 secunet Security Networks AG
+ *
+ *	Author:
+ *	Steffen Klassert <steffen.klassert@secunet.com>
+ */
+
+#include <linux/module.h>
+#include <linux/capability.h>
+#include <linux/errno.h>
+#include <linux/types.h>
+#include <linux/sockios.h>
+#include <linux/icmp.h>
+#include <linux/if.h>
+#include <linux/in.h>
+#include <linux/ip.h>
+#include <linux/net.h>
+#include <linux/in6.h>
+#include <linux/netdevice.h>
+#include <linux/if_link.h>
+#include <linux/if_arp.h>
+#include <linux/icmpv6.h>
+#include <linux/init.h>
+#include <linux/route.h>
+#include <linux/rtnetlink.h>
+#include <linux/netfilter_ipv6.h>
+#include <linux/slab.h>
+#include <linux/hash.h>
+
+#include <linux/uaccess.h>
+#include <linux/atomic.h>
+
+#include <net/icmp.h>
+#include <net/ip.h>
+#include <net/ipv6.h>
+#include <net/ip6_route.h>
+#include <net/ip_tunnels.h>
+#include <net/addrconf.h>
+#include <net/xfrm.h>
+#include <net/net_namespace.h>
+#include <net/netns/generic.h>
+#include <linux/etherdevice.h>
+
+static int xfrmi_dev_init(struct net_device *dev);
+static void xfrmi_dev_setup(struct net_device *dev);
+static struct rtnl_link_ops xfrmi_link_ops __read_mostly;
+static unsigned int xfrmi_net_id __read_mostly;
+static const struct net_device_ops xfrmi_netdev_ops;
+
+#define XFRMI_HASH_BITS	8
+#define XFRMI_HASH_SIZE	BIT(XFRMI_HASH_BITS)
+
+struct xfrmi_net {
+	/* lists for storing interfaces in use */
+	struct xfrm_if __rcu *xfrmi[XFRMI_HASH_SIZE];
+};
+
+#define for_each_xfrmi_rcu(start, xi) \
+	for (xi = rcu_dereference(start); xi; xi = rcu_dereference(xi->next))
+
+static u32 xfrmi_hash(u32 if_id)
+{
+	return hash_32(if_id, XFRMI_HASH_BITS);
+}
+
+static struct xfrm_if *xfrmi_lookup(struct net *net, struct xfrm_state *x)
+{
+	struct xfrmi_net *xfrmn = net_generic(net, xfrmi_net_id);
+	struct xfrm_if *xi;
+
+	for_each_xfrmi_rcu(xfrmn->xfrmi[xfrmi_hash(x->if_id)], xi) {
+		if (x->if_id == xi->p.if_id &&
+		    (xi->dev->flags & IFF_UP))
+			return xi;
+	}
+
+	return NULL;
+}
+
+static struct xfrm_if *xfrmi_decode_session(struct sk_buff *skb,
+					    unsigned short family)
+{
+	struct net_device *dev;
+	int ifindex = 0;
+
+	if (!secpath_exists(skb) || !skb->dev)
+		return NULL;
+
+	switch (family) {
+	case AF_INET6:
+		ifindex = inet6_sdif(skb);
+		break;
+	case AF_INET:
+		ifindex = inet_sdif(skb);
+		break;
+	}
+
+	if (ifindex) {
+		struct net *net = xs_net(xfrm_input_state(skb));
+
+		dev = dev_get_by_index_rcu(net, ifindex);
+	} else {
+		dev = skb->dev;
+	}
+
+	if (!dev || !(dev->flags & IFF_UP))
+		return NULL;
+	if (dev->netdev_ops != &xfrmi_netdev_ops)
+		return NULL;
+
+	return netdev_priv(dev);
+}
+
+static void xfrmi_link(struct xfrmi_net *xfrmn, struct xfrm_if *xi)
+{
+	struct xfrm_if __rcu **xip = &xfrmn->xfrmi[xfrmi_hash(xi->p.if_id)];
+
+	rcu_assign_pointer(xi->next , rtnl_dereference(*xip));
+	rcu_assign_pointer(*xip, xi);
+}
+
+static void xfrmi_unlink(struct xfrmi_net *xfrmn, struct xfrm_if *xi)
+{
+	struct xfrm_if __rcu **xip;
+	struct xfrm_if *iter;
+
+	for (xip = &xfrmn->xfrmi[xfrmi_hash(xi->p.if_id)];
+	     (iter = rtnl_dereference(*xip)) != NULL;
+	     xip = &iter->next) {
+		if (xi == iter) {
+			rcu_assign_pointer(*xip, xi->next);
+			break;
+		}
+	}
+}
+
+static void xfrmi_dev_free(struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+
+	gro_cells_destroy(&xi->gro_cells);
+	free_percpu(dev->tstats);
+}
+
+static int xfrmi_create(struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct net *net = dev_net(dev);
+	struct xfrmi_net *xfrmn = net_generic(net, xfrmi_net_id);
+	int err;
+
+	dev->rtnl_link_ops = &xfrmi_link_ops;
+	err = register_netdevice(dev);
+	if (err < 0)
+		goto out;
+
+	xfrmi_link(xfrmn, xi);
+
+	return 0;
+
+out:
+	return err;
+}
+
+static struct xfrm_if *xfrmi_locate(struct net *net, struct xfrm_if_parms *p)
+{
+	struct xfrm_if __rcu **xip;
+	struct xfrm_if *xi;
+	struct xfrmi_net *xfrmn = net_generic(net, xfrmi_net_id);
+
+	for (xip = &xfrmn->xfrmi[xfrmi_hash(p->if_id)];
+	     (xi = rtnl_dereference(*xip)) != NULL;
+	     xip = &xi->next)
+		if (xi->p.if_id == p->if_id)
+			return xi;
+
+	return NULL;
+}
+
+static void xfrmi_dev_uninit(struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct xfrmi_net *xfrmn = net_generic(xi->net, xfrmi_net_id);
+
+	xfrmi_unlink(xfrmn, xi);
+}
+
+static void xfrmi_scrub_packet(struct sk_buff *skb, bool xnet)
+{
+	skb->tstamp = 0;
+	skb->pkt_type = PACKET_HOST;
+	skb->skb_iif = 0;
+	skb->ignore_df = 0;
+	skb_dst_drop(skb);
+	nf_reset_ct(skb);
+	nf_reset_trace(skb);
+
+	if (!xnet)
+		return;
+
+	ipvs_reset(skb);
+	secpath_reset(skb);
+	skb_orphan(skb);
+	skb->mark = 0;
+}
+
+static int xfrmi_input(struct sk_buff *skb, int nexthdr, __be32 spi,
+		       int encap_type, unsigned short family)
+{
+	struct sec_path *sp;
+
+	sp = skb_sec_path(skb);
+	if (sp && (sp->len || sp->olen) &&
+	    !xfrm_policy_check(NULL, XFRM_POLICY_IN, skb, family))
+		goto discard;
+
+	XFRM_SPI_SKB_CB(skb)->family = family;
+	if (family == AF_INET) {
+		XFRM_SPI_SKB_CB(skb)->daddroff = offsetof(struct iphdr, daddr);
+		XFRM_TUNNEL_SKB_CB(skb)->tunnel.ip4 = NULL;
+	} else {
+		XFRM_SPI_SKB_CB(skb)->daddroff = offsetof(struct ipv6hdr, daddr);
+		XFRM_TUNNEL_SKB_CB(skb)->tunnel.ip6 = NULL;
+	}
+
+	return xfrm_input(skb, nexthdr, spi, encap_type);
+discard:
+	kfree_skb(skb);
+	return 0;
+}
+
+static int xfrmi4_rcv(struct sk_buff *skb)
+{
+	return xfrmi_input(skb, ip_hdr(skb)->protocol, 0, 0, AF_INET);
+}
+
+static int xfrmi6_rcv(struct sk_buff *skb)
+{
+	return xfrmi_input(skb, skb_network_header(skb)[IP6CB(skb)->nhoff],
+			   0, 0, AF_INET6);
+}
+
+static int xfrmi4_input(struct sk_buff *skb, int nexthdr, __be32 spi, int encap_type)
+{
+	return xfrmi_input(skb, nexthdr, spi, encap_type, AF_INET);
+}
+
+static int xfrmi6_input(struct sk_buff *skb, int nexthdr, __be32 spi, int encap_type)
+{
+	return xfrmi_input(skb, nexthdr, spi, encap_type, AF_INET6);
+}
+
+static int xfrmi_rcv_cb(struct sk_buff *skb, int err)
+{
+	const struct xfrm_mode *inner_mode;
+	struct net_device *dev;
+	struct xfrm_state *x;
+	struct xfrm_if *xi;
+	bool xnet;
+
+	if (err && !secpath_exists(skb))
+		return 0;
+
+	x = xfrm_input_state(skb);
+
+	xi = xfrmi_lookup(xs_net(x), x);
+	if (!xi)
+		return 1;
+
+	dev = xi->dev;
+	skb->dev = dev;
+
+	if (err) {
+		DEV_STATS_INC(dev, rx_errors);
+		DEV_STATS_INC(dev, rx_dropped);
+
+		return 0;
+	}
+
+	xnet = !net_eq(xi->net, dev_net(skb->dev));
+
+	if (xnet) {
+		inner_mode = &x->inner_mode;
+
+		if (x->sel.family == AF_UNSPEC) {
+			inner_mode = xfrm_ip2inner_mode(x, XFRM_MODE_SKB_CB(skb)->protocol);
+			if (inner_mode == NULL) {
+				XFRM_INC_STATS(dev_net(skb->dev),
+					       LINUX_MIB_XFRMINSTATEMODEERROR);
+				return -EINVAL;
+			}
+		}
+
+		if (!xfrm_policy_check(NULL, XFRM_POLICY_IN, skb,
+				       inner_mode->family))
+			return -EPERM;
+	}
+
+	xfrmi_scrub_packet(skb, xnet);
+	dev_sw_netstats_rx_add(dev, skb->len);
+
+	return 0;
+}
+
+static int
+xfrmi_xmit2(struct sk_buff *skb, struct net_device *dev, struct flowi *fl)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct dst_entry *dst = skb_dst(skb);
+	unsigned int length = skb->len;
+	struct net_device *tdev;
+	struct xfrm_state *x;
+	int err = -1;
+	int mtu;
+
+	dst_hold(dst);
+	dst = xfrm_lookup_with_ifid(xi->net, dst, fl, NULL, 0, xi->p.if_id);
+	if (IS_ERR(dst)) {
+		err = PTR_ERR(dst);
+		dst = NULL;
+		goto tx_err_link_failure;
+	}
+
+	x = dst->xfrm;
+	if (!x)
+		goto tx_err_link_failure;
+
+	if (x->if_id != xi->p.if_id)
+		goto tx_err_link_failure;
+
+	tdev = dst->dev;
+
+	if (tdev == dev) {
+		DEV_STATS_INC(dev, collisions);
+		net_warn_ratelimited("%s: Local routing loop detected!\n",
+				     dev->name);
+		goto tx_err_dst_release;
+	}
+
+	mtu = dst_mtu(dst);
+	if ((!skb_is_gso(skb) && skb->len > mtu) ||
+	    (skb_is_gso(skb) && !skb_gso_validate_network_len(skb, mtu))) {
+		skb_dst_update_pmtu_no_confirm(skb, mtu);
+
+		if (skb->protocol == htons(ETH_P_IPV6)) {
+			if (mtu < IPV6_MIN_MTU)
+				mtu = IPV6_MIN_MTU;
+
+			if (skb->len > 1280)
+				icmpv6_ndo_send(skb, ICMPV6_PKT_TOOBIG, 0, mtu);
+			else
+				goto xmit;
+		} else {
+			if (!(ip_hdr(skb)->frag_off & htons(IP_DF)))
+				goto xmit;
+			icmp_ndo_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED,
+				      htonl(mtu));
+		}
+
+		dst_release(dst);
+		return -EMSGSIZE;
+	}
+
+xmit:
+	xfrmi_scrub_packet(skb, !net_eq(xi->net, dev_net(dev)));
+	skb_dst_set(skb, dst);
+	skb->dev = tdev;
+
+	err = dst_output(xi->net, skb->sk, skb);
+	if (net_xmit_eval(err) == 0) {
+		dev_sw_netstats_tx_add(dev, 1, length);
+	} else {
+		DEV_STATS_INC(dev, tx_errors);
+		DEV_STATS_INC(dev, tx_aborted_errors);
+	}
+
+	return 0;
+tx_err_link_failure:
+	DEV_STATS_INC(dev, tx_carrier_errors);
+	dst_link_failure(skb);
+tx_err_dst_release:
+	dst_release(dst);
+	return err;
+}
+
+static netdev_tx_t xfrmi_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct dst_entry *dst = skb_dst(skb);
+	struct flowi fl;
+	int ret;
+
+	memset(&fl, 0, sizeof(fl));
+
+	switch (skb->protocol) {
+	case htons(ETH_P_IPV6):
+		memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
+		xfrm_decode_session(skb, &fl, AF_INET6);
+		if (!dst) {
+			fl.u.ip6.flowi6_oif = dev->ifindex;
+			fl.u.ip6.flowi6_flags |= FLOWI_FLAG_ANYSRC;
+			dst = ip6_route_output(dev_net(dev), NULL, &fl.u.ip6);
+			if (dst->error) {
+				dst_release(dst);
+				DEV_STATS_INC(dev, tx_carrier_errors);
+				goto tx_err;
+			}
+			skb_dst_set(skb, dst);
+		}
+		break;
+	case htons(ETH_P_IP):
+		memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
+		xfrm_decode_session(skb, &fl, AF_INET);
+		if (!dst) {
+			struct rtable *rt;
+
+			fl.u.ip4.flowi4_oif = dev->ifindex;
+			fl.u.ip4.flowi4_flags |= FLOWI_FLAG_ANYSRC;
+			rt = __ip_route_output_key(dev_net(dev), &fl.u.ip4);
+			if (IS_ERR(rt)) {
+				DEV_STATS_INC(dev, tx_carrier_errors);
+				goto tx_err;
+			}
+			skb_dst_set(skb, &rt->dst);
+		}
+		break;
+	default:
+		goto tx_err;
+	}
+
+	fl.flowi_oif = xi->p.link;
+
+	ret = xfrmi_xmit2(skb, dev, &fl);
+	if (ret < 0)
+		goto tx_err;
+
+	return NETDEV_TX_OK;
+
+tx_err:
+	DEV_STATS_INC(dev, tx_errors);
+	DEV_STATS_INC(dev, tx_dropped);
+	kfree_skb(skb);
+	return NETDEV_TX_OK;
+}
+
+static int xfrmi4_err(struct sk_buff *skb, u32 info)
+{
+	const struct iphdr *iph = (const struct iphdr *)skb->data;
+	struct net *net = dev_net(skb->dev);
+	int protocol = iph->protocol;
+	struct ip_comp_hdr *ipch;
+	struct ip_esp_hdr *esph;
+	struct ip_auth_hdr *ah ;
+	struct xfrm_state *x;
+	struct xfrm_if *xi;
+	__be32 spi;
+
+	switch (protocol) {
+	case IPPROTO_ESP:
+		esph = (struct ip_esp_hdr *)(skb->data+(iph->ihl<<2));
+		spi = esph->spi;
+		break;
+	case IPPROTO_AH:
+		ah = (struct ip_auth_hdr *)(skb->data+(iph->ihl<<2));
+		spi = ah->spi;
+		break;
+	case IPPROTO_COMP:
+		ipch = (struct ip_comp_hdr *)(skb->data+(iph->ihl<<2));
+		spi = htonl(ntohs(ipch->cpi));
+		break;
+	default:
+		return 0;
+	}
+
+	switch (icmp_hdr(skb)->type) {
+	case ICMP_DEST_UNREACH:
+		if (icmp_hdr(skb)->code != ICMP_FRAG_NEEDED)
+			return 0;
+		break;
+	case ICMP_REDIRECT:
+		break;
+	default:
+		return 0;
+	}
+
+	x = xfrm_state_lookup(net, skb->mark, (const xfrm_address_t *)&iph->daddr,
+			      spi, protocol, AF_INET);
+	if (!x)
+		return 0;
+
+	xi = xfrmi_lookup(net, x);
+	if (!xi) {
+		xfrm_state_put(x);
+		return -1;
+	}
+
+	if (icmp_hdr(skb)->type == ICMP_DEST_UNREACH)
+		ipv4_update_pmtu(skb, net, info, 0, protocol);
+	else
+		ipv4_redirect(skb, net, 0, protocol);
+	xfrm_state_put(x);
+
+	return 0;
+}
+
+static int xfrmi6_err(struct sk_buff *skb, struct inet6_skb_parm *opt,
+		    u8 type, u8 code, int offset, __be32 info)
+{
+	const struct ipv6hdr *iph = (const struct ipv6hdr *)skb->data;
+	struct net *net = dev_net(skb->dev);
+	int protocol = iph->nexthdr;
+	struct ip_comp_hdr *ipch;
+	struct ip_esp_hdr *esph;
+	struct ip_auth_hdr *ah;
+	struct xfrm_state *x;
+	struct xfrm_if *xi;
+	__be32 spi;
+
+	switch (protocol) {
+	case IPPROTO_ESP:
+		esph = (struct ip_esp_hdr *)(skb->data + offset);
+		spi = esph->spi;
+		break;
+	case IPPROTO_AH:
+		ah = (struct ip_auth_hdr *)(skb->data + offset);
+		spi = ah->spi;
+		break;
+	case IPPROTO_COMP:
+		ipch = (struct ip_comp_hdr *)(skb->data + offset);
+		spi = htonl(ntohs(ipch->cpi));
+		break;
+	default:
+		return 0;
+	}
+
+	if (type != ICMPV6_PKT_TOOBIG &&
+	    type != NDISC_REDIRECT)
+		return 0;
+
+	x = xfrm_state_lookup(net, skb->mark, (const xfrm_address_t *)&iph->daddr,
+			      spi, protocol, AF_INET6);
+	if (!x)
+		return 0;
+
+	xi = xfrmi_lookup(net, x);
+	if (!xi) {
+		xfrm_state_put(x);
+		return -1;
+	}
+
+	if (type == NDISC_REDIRECT)
+		ip6_redirect(skb, net, skb->dev->ifindex, 0,
+			     sock_net_uid(net, NULL));
+	else
+		ip6_update_pmtu(skb, net, info, 0, 0, sock_net_uid(net, NULL));
+	xfrm_state_put(x);
+
+	return 0;
+}
+
+static int xfrmi_change(struct xfrm_if *xi, const struct xfrm_if_parms *p)
+{
+	if (xi->p.link != p->link)
+		return -EINVAL;
+
+	xi->p.if_id = p->if_id;
+
+	return 0;
+}
+
+static int xfrmi_update(struct xfrm_if *xi, struct xfrm_if_parms *p)
+{
+	struct net *net = xi->net;
+	struct xfrmi_net *xfrmn = net_generic(net, xfrmi_net_id);
+	int err;
+
+	xfrmi_unlink(xfrmn, xi);
+	synchronize_net();
+	err = xfrmi_change(xi, p);
+	xfrmi_link(xfrmn, xi);
+	netdev_state_change(xi->dev);
+	return err;
+}
+
+static int xfrmi_get_iflink(const struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+
+	return xi->p.link;
+}
+
+static const struct net_device_ops xfrmi_netdev_ops = {
+	.ndo_init	= xfrmi_dev_init,
+	.ndo_uninit	= xfrmi_dev_uninit,
+	.ndo_start_xmit = xfrmi_xmit,
+	.ndo_get_stats64 = dev_get_tstats64,
+	.ndo_get_iflink = xfrmi_get_iflink,
+};
+
+static void xfrmi_dev_setup(struct net_device *dev)
+{
+	dev->netdev_ops 	= &xfrmi_netdev_ops;
+	dev->header_ops		= &ip_tunnel_header_ops;
+	dev->type		= ARPHRD_NONE;
+	dev->mtu		= ETH_DATA_LEN;
+	dev->min_mtu		= ETH_MIN_MTU;
+	dev->max_mtu		= IP_MAX_MTU;
+	dev->flags 		= IFF_NOARP;
+	dev->needs_free_netdev	= true;
+	dev->priv_destructor	= xfrmi_dev_free;
+	netif_keep_dst(dev);
+
+	eth_broadcast_addr(dev->broadcast);
+}
+
+#define XFRMI_FEATURES (NETIF_F_SG |		\
+			NETIF_F_FRAGLIST |	\
+			NETIF_F_GSO_SOFTWARE |	\
+			NETIF_F_HW_CSUM)
+
+static int xfrmi_dev_init(struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct net_device *phydev = __dev_get_by_index(xi->net, xi->p.link);
+	int err;
+
+	dev->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
+	if (!dev->tstats)
+		return -ENOMEM;
+
+	err = gro_cells_init(&xi->gro_cells, dev);
+	if (err) {
+		free_percpu(dev->tstats);
+		return err;
+	}
+
+	dev->features |= NETIF_F_LLTX;
+	dev->features |= XFRMI_FEATURES;
+	dev->hw_features |= XFRMI_FEATURES;
+
+	if (phydev) {
+		dev->needed_headroom = phydev->needed_headroom;
+		dev->needed_tailroom = phydev->needed_tailroom;
+
+		if (is_zero_ether_addr(dev->dev_addr))
+			eth_hw_addr_inherit(dev, phydev);
+		if (is_zero_ether_addr(dev->broadcast))
+			memcpy(dev->broadcast, phydev->broadcast,
+			       dev->addr_len);
+	} else {
+		eth_hw_addr_random(dev);
+		eth_broadcast_addr(dev->broadcast);
+	}
+
+	return 0;
+}
+
+static int xfrmi_validate(struct nlattr *tb[], struct nlattr *data[],
+			 struct netlink_ext_ack *extack)
+{
+	return 0;
+}
+
+static void xfrmi_netlink_parms(struct nlattr *data[],
+			       struct xfrm_if_parms *parms)
+{
+	memset(parms, 0, sizeof(*parms));
+
+	if (!data)
+		return;
+
+	if (data[IFLA_XFRM_LINK])
+		parms->link = nla_get_u32(data[IFLA_XFRM_LINK]);
+
+	if (data[IFLA_XFRM_IF_ID])
+		parms->if_id = nla_get_u32(data[IFLA_XFRM_IF_ID]);
+}
+
+static int xfrmi_newlink(struct net *src_net, struct net_device *dev,
+			struct nlattr *tb[], struct nlattr *data[],
+			struct netlink_ext_ack *extack)
+{
+	struct net *net = dev_net(dev);
+	struct xfrm_if_parms p = {};
+	struct xfrm_if *xi;
+	int err;
+
+	xfrmi_netlink_parms(data, &p);
+	if (!p.if_id) {
+		NL_SET_ERR_MSG(extack, "if_id must be non zero");
+		return -EINVAL;
+	}
+
+	xi = xfrmi_locate(net, &p);
+	if (xi)
+		return -EEXIST;
+
+	xi = netdev_priv(dev);
+	xi->p = p;
+	xi->net = net;
+	xi->dev = dev;
+
+	err = xfrmi_create(dev);
+	return err;
+}
+
+static void xfrmi_dellink(struct net_device *dev, struct list_head *head)
+{
+	unregister_netdevice_queue(dev, head);
+}
+
+static int xfrmi_changelink(struct net_device *dev, struct nlattr *tb[],
+			   struct nlattr *data[],
+			   struct netlink_ext_ack *extack)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct net *net = xi->net;
+	struct xfrm_if_parms p = {};
+
+	xfrmi_netlink_parms(data, &p);
+	if (!p.if_id) {
+		NL_SET_ERR_MSG(extack, "if_id must be non zero");
+		return -EINVAL;
+	}
+
+	xi = xfrmi_locate(net, &p);
+	if (!xi) {
+		xi = netdev_priv(dev);
+	} else {
+		if (xi->dev != dev)
+			return -EEXIST;
+	}
+
+	return xfrmi_update(xi, &p);
+}
+
+static size_t xfrmi_get_size(const struct net_device *dev)
+{
+	return
+		/* IFLA_XFRM_LINK */
+		nla_total_size(4) +
+		/* IFLA_XFRM_IF_ID */
+		nla_total_size(4) +
+		0;
+}
+
+static int xfrmi_fill_info(struct sk_buff *skb, const struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+	struct xfrm_if_parms *parm = &xi->p;
+
+	if (nla_put_u32(skb, IFLA_XFRM_LINK, parm->link) ||
+	    nla_put_u32(skb, IFLA_XFRM_IF_ID, parm->if_id))
+		goto nla_put_failure;
+	return 0;
+
+nla_put_failure:
+	return -EMSGSIZE;
+}
+
+static struct net *xfrmi_get_link_net(const struct net_device *dev)
+{
+	struct xfrm_if *xi = netdev_priv(dev);
+
+	return xi->net;
+}
+
+static const struct nla_policy xfrmi_policy[IFLA_XFRM_MAX + 1] = {
+	[IFLA_XFRM_LINK]	= { .type = NLA_U32 },
+	[IFLA_XFRM_IF_ID]	= { .type = NLA_U32 },
+};
+
+static struct rtnl_link_ops xfrmi_link_ops __read_mostly = {
+	.kind		= "xfrm",
+	.maxtype	= IFLA_XFRM_MAX,
+	.policy		= xfrmi_policy,
+	.priv_size	= sizeof(struct xfrm_if),
+	.setup		= xfrmi_dev_setup,
+	.validate	= xfrmi_validate,
+	.newlink	= xfrmi_newlink,
+	.dellink	= xfrmi_dellink,
+	.changelink	= xfrmi_changelink,
+	.get_size	= xfrmi_get_size,
+	.fill_info	= xfrmi_fill_info,
+	.get_link_net	= xfrmi_get_link_net,
+};
+
+static void __net_exit xfrmi_exit_batch_net(struct list_head *net_exit_list)
+{
+	struct net *net;
+	LIST_HEAD(list);
+
+	rtnl_lock();
+	list_for_each_entry(net, net_exit_list, exit_list) {
+		struct xfrmi_net *xfrmn = net_generic(net, xfrmi_net_id);
+		struct xfrm_if __rcu **xip;
+		struct xfrm_if *xi;
+		int i;
+
+		for (i = 0; i < XFRMI_HASH_SIZE; i++) {
+			for (xip = &xfrmn->xfrmi[i];
+			     (xi = rtnl_dereference(*xip)) != NULL;
+			     xip = &xi->next)
+				unregister_netdevice_queue(xi->dev, &list);
+		}
+	}
+	unregister_netdevice_many(&list);
+	rtnl_unlock();
+}
+
+static struct pernet_operations xfrmi_net_ops = {
+	.exit_batch = xfrmi_exit_batch_net,
+	.id   = &xfrmi_net_id,
+	.size = sizeof(struct xfrmi_net),
+};
+
+static struct xfrm6_protocol xfrmi_esp6_protocol __read_mostly = {
+	.handler	=	xfrmi6_rcv,
+	.input_handler	=	xfrmi6_input,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi6_err,
+	.priority	=	10,
+};
+
+static struct xfrm6_protocol xfrmi_ah6_protocol __read_mostly = {
+	.handler	=	xfrm6_rcv,
+	.input_handler	=	xfrm_input,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi6_err,
+	.priority	=	10,
+};
+
+static struct xfrm6_protocol xfrmi_ipcomp6_protocol __read_mostly = {
+	.handler	=	xfrm6_rcv,
+	.input_handler	=	xfrm_input,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi6_err,
+	.priority	=	10,
+};
+
+#if IS_REACHABLE(CONFIG_INET6_XFRM_TUNNEL)
+static int xfrmi6_rcv_tunnel(struct sk_buff *skb)
+{
+	const xfrm_address_t *saddr;
+	__be32 spi;
+
+	saddr = (const xfrm_address_t *)&ipv6_hdr(skb)->saddr;
+	spi = xfrm6_tunnel_spi_lookup(dev_net(skb->dev), saddr);
+
+	return xfrm6_rcv_spi(skb, IPPROTO_IPV6, spi, NULL);
+}
+
+static struct xfrm6_tunnel xfrmi_ipv6_handler __read_mostly = {
+	.handler	=	xfrmi6_rcv_tunnel,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi6_err,
+	.priority	=	2,
+};
+
+static struct xfrm6_tunnel xfrmi_ip6ip_handler __read_mostly = {
+	.handler	=	xfrmi6_rcv_tunnel,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi6_err,
+	.priority	=	2,
+};
+#endif
+
+static struct xfrm4_protocol xfrmi_esp4_protocol __read_mostly = {
+	.handler	=	xfrmi4_rcv,
+	.input_handler	=	xfrmi4_input,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi4_err,
+	.priority	=	10,
+};
+
+static struct xfrm4_protocol xfrmi_ah4_protocol __read_mostly = {
+	.handler	=	xfrm4_rcv,
+	.input_handler	=	xfrm_input,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi4_err,
+	.priority	=	10,
+};
+
+static struct xfrm4_protocol xfrmi_ipcomp4_protocol __read_mostly = {
+	.handler	=	xfrm4_rcv,
+	.input_handler	=	xfrm_input,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi4_err,
+	.priority	=	10,
+};
+
+#if IS_REACHABLE(CONFIG_INET_XFRM_TUNNEL)
+static int xfrmi4_rcv_tunnel(struct sk_buff *skb)
+{
+	return xfrm4_rcv_spi(skb, IPPROTO_IPIP, ip_hdr(skb)->saddr);
+}
+
+static struct xfrm_tunnel xfrmi_ipip_handler __read_mostly = {
+	.handler	=	xfrmi4_rcv_tunnel,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi4_err,
+	.priority	=	3,
+};
+
+static struct xfrm_tunnel xfrmi_ipip6_handler __read_mostly = {
+	.handler	=	xfrmi4_rcv_tunnel,
+	.cb_handler	=	xfrmi_rcv_cb,
+	.err_handler	=	xfrmi4_err,
+	.priority	=	2,
+};
+#endif
+
+static int __init xfrmi4_init(void)
+{
+	int err;
+
+	err = xfrm4_protocol_register(&xfrmi_esp4_protocol, IPPROTO_ESP);
+	if (err < 0)
+		goto xfrm_proto_esp_failed;
+	err = xfrm4_protocol_register(&xfrmi_ah4_protocol, IPPROTO_AH);
+	if (err < 0)
+		goto xfrm_proto_ah_failed;
+	err = xfrm4_protocol_register(&xfrmi_ipcomp4_protocol, IPPROTO_COMP);
+	if (err < 0)
+		goto xfrm_proto_comp_failed;
+#if IS_REACHABLE(CONFIG_INET_XFRM_TUNNEL)
+	err = xfrm4_tunnel_register(&xfrmi_ipip_handler, AF_INET);
+	if (err < 0)
+		goto xfrm_tunnel_ipip_failed;
+	err = xfrm4_tunnel_register(&xfrmi_ipip6_handler, AF_INET6);
+	if (err < 0)
+		goto xfrm_tunnel_ipip6_failed;
+#endif
+
+	return 0;
+
+#if IS_REACHABLE(CONFIG_INET_XFRM_TUNNEL)
+xfrm_tunnel_ipip6_failed:
+	xfrm4_tunnel_deregister(&xfrmi_ipip_handler, AF_INET);
+xfrm_tunnel_ipip_failed:
+	xfrm4_protocol_deregister(&xfrmi_ipcomp4_protocol, IPPROTO_COMP);
+#endif
+xfrm_proto_comp_failed:
+	xfrm4_protocol_deregister(&xfrmi_ah4_protocol, IPPROTO_AH);
+xfrm_proto_ah_failed:
+	xfrm4_protocol_deregister(&xfrmi_esp4_protocol, IPPROTO_ESP);
+xfrm_proto_esp_failed:
+	return err;
+}
+
+static void xfrmi4_fini(void)
+{
+#if IS_REACHABLE(CONFIG_INET_XFRM_TUNNEL)
+	xfrm4_tunnel_deregister(&xfrmi_ipip6_handler, AF_INET6);
+	xfrm4_tunnel_deregister(&xfrmi_ipip_handler, AF_INET);
+#endif
+	xfrm4_protocol_deregister(&xfrmi_ipcomp4_protocol, IPPROTO_COMP);
+	xfrm4_protocol_deregister(&xfrmi_ah4_protocol, IPPROTO_AH);
+	xfrm4_protocol_deregister(&xfrmi_esp4_protocol, IPPROTO_ESP);
+}
+
+static int __init xfrmi6_init(void)
+{
+	int err;
+
+	err = xfrm6_protocol_register(&xfrmi_esp6_protocol, IPPROTO_ESP);
+	if (err < 0)
+		goto xfrm_proto_esp_failed;
+	err = xfrm6_protocol_register(&xfrmi_ah6_protocol, IPPROTO_AH);
+	if (err < 0)
+		goto xfrm_proto_ah_failed;
+	err = xfrm6_protocol_register(&xfrmi_ipcomp6_protocol, IPPROTO_COMP);
+	if (err < 0)
+		goto xfrm_proto_comp_failed;
+#if IS_REACHABLE(CONFIG_INET6_XFRM_TUNNEL)
+	err = xfrm6_tunnel_register(&xfrmi_ipv6_handler, AF_INET6);
+	if (err < 0)
+		goto xfrm_tunnel_ipv6_failed;
+	err = xfrm6_tunnel_register(&xfrmi_ip6ip_handler, AF_INET);
+	if (err < 0)
+		goto xfrm_tunnel_ip6ip_failed;
+#endif
+
+	return 0;
+
+#if IS_REACHABLE(CONFIG_INET6_XFRM_TUNNEL)
+xfrm_tunnel_ip6ip_failed:
+	xfrm6_tunnel_deregister(&xfrmi_ipv6_handler, AF_INET6);
+xfrm_tunnel_ipv6_failed:
+	xfrm6_protocol_deregister(&xfrmi_ipcomp6_protocol, IPPROTO_COMP);
+#endif
+xfrm_proto_comp_failed:
+	xfrm6_protocol_deregister(&xfrmi_ah6_protocol, IPPROTO_AH);
+xfrm_proto_ah_failed:
+	xfrm6_protocol_deregister(&xfrmi_esp6_protocol, IPPROTO_ESP);
+xfrm_proto_esp_failed:
+	return err;
+}
+
+static void xfrmi6_fini(void)
+{
+#if IS_REACHABLE(CONFIG_INET6_XFRM_TUNNEL)
+	xfrm6_tunnel_deregister(&xfrmi_ip6ip_handler, AF_INET);
+	xfrm6_tunnel_deregister(&xfrmi_ipv6_handler, AF_INET6);
+#endif
+	xfrm6_protocol_deregister(&xfrmi_ipcomp6_protocol, IPPROTO_COMP);
+	xfrm6_protocol_deregister(&xfrmi_ah6_protocol, IPPROTO_AH);
+	xfrm6_protocol_deregister(&xfrmi_esp6_protocol, IPPROTO_ESP);
+}
+
+static const struct xfrm_if_cb xfrm_if_cb = {
+	.decode_session =	xfrmi_decode_session,
+};
+
+static int __init xfrmi_init(void)
+{
+	const char *msg;
+	int err;
+
+	pr_info("IPsec XFRM device driver\n");
+
+	msg = "tunnel device";
+	err = register_pernet_device(&xfrmi_net_ops);
+	if (err < 0)
+		goto pernet_dev_failed;
+
+	msg = "xfrm4 protocols";
+	err = xfrmi4_init();
+	if (err < 0)
+		goto xfrmi4_failed;
+
+	msg = "xfrm6 protocols";
+	err = xfrmi6_init();
+	if (err < 0)
+		goto xfrmi6_failed;
+
+
+	msg = "netlink interface";
+	err = rtnl_link_register(&xfrmi_link_ops);
+	if (err < 0)
+		goto rtnl_link_failed;
+
+	xfrm_if_register_cb(&xfrm_if_cb);
+
+	return err;
+
+rtnl_link_failed:
+	xfrmi6_fini();
+xfrmi6_failed:
+	xfrmi4_fini();
+xfrmi4_failed:
+	unregister_pernet_device(&xfrmi_net_ops);
+pernet_dev_failed:
+	pr_err("xfrmi init: failed to register %s\n", msg);
+	return err;
+}
+
+static void __exit xfrmi_fini(void)
+{
+	xfrm_if_unregister_cb();
+	rtnl_link_unregister(&xfrmi_link_ops);
+	xfrmi4_fini();
+	xfrmi6_fini();
+	unregister_pernet_device(&xfrmi_net_ops);
+}
+
+module_init(xfrmi_init);
+module_exit(xfrmi_fini);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_RTNL_LINK("xfrm");
+MODULE_ALIAS_NETDEV("xfrm0");
+MODULE_AUTHOR("Steffen Klassert");
+MODULE_DESCRIPTION("XFRM virtual interface");
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_ipcomp.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_ipcomp.c
@@ -203,6 +203,7 @@
 		vfree(*per_cpu_ptr(scratches, i));
 
 	free_percpu(scratches);
+	ipcomp_scratches = NULL;
 }
 
 static void * __percpu *ipcomp_alloc_scratches(void)
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_output.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_output.c
@@ -647,10 +647,12 @@
  * This requires hardware to know the inner packet type to calculate
  * the inner header checksum. Save inner ip protocol here to avoid
  * traversing the packet in the vendor's xmit code.
- * If the encap type is IPIP, just save skb->inner_ipproto. Otherwise,
- * get the ip protocol from the IP header.
+ * For IPsec tunnel mode save the ip protocol from the IP header of the
+ * plain text packet. Otherwise If the encap type is IPIP, just save
+ * skb->inner_ipproto in any other case get the ip protocol from the IP
+ * header.
  */
-static void xfrm_get_inner_ipproto(struct sk_buff *skb)
+static void xfrm_get_inner_ipproto(struct sk_buff *skb, struct xfrm_state *x)
 {
 	struct xfrm_offload *xo = xfrm_offload(skb);
 	const struct ethhdr *eth;
@@ -658,6 +660,25 @@
 	if (!xo)
 		return;
 
+	if (x->outer_mode.encap == XFRM_MODE_TUNNEL) {
+		switch (x->outer_mode.family) {
+		case AF_INET:
+			xo->inner_ipproto = ip_hdr(skb)->protocol;
+			break;
+		case AF_INET6:
+			xo->inner_ipproto = ipv6_hdr(skb)->nexthdr;
+			break;
+		default:
+			break;
+		}
+
+		return;
+	}
+
+	/* non-Tunnel Mode */
+	if (!skb->encapsulation)
+		return;
+
 	if (skb->inner_protocol_type == ENCAP_TYPE_IPPROTO) {
 		xo->inner_ipproto = skb->inner_ipproto;
 		return;
@@ -712,12 +733,11 @@
 		sp->xvec[sp->len++] = x;
 		xfrm_state_hold(x);
 
-		if (skb->encapsulation)
-			xfrm_get_inner_ipproto(skb);
+		xfrm_get_inner_ipproto(skb, x);
 		skb->encapsulation = 1;
 
 		if (skb_is_gso(skb)) {
-			if (skb->inner_protocol)
+			if (skb->inner_protocol && x->props.mode == XFRM_MODE_TUNNEL)
 				return xfrm_output_gso(net, sk, skb);
 
 			skb_shinfo(skb)->gso_type |= SKB_GSO_ESP;
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_policy.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_policy.c
@@ -31,8 +31,10 @@
 #include <linux/if_tunnel.h>
 #include <net/dst.h>
 #include <net/flow.h>
+#include <net/inet_ecn.h>
 #include <net/xfrm.h>
 #include <net/ip.h>
+#include <net/gre.h>
 #if IS_ENABLED(CONFIG_IPV6_MIP6)
 #include <net/mip6.h>
 #endif
@@ -249,10 +251,8 @@
 	return rcu_dereference(xfrm_if_cb);
 }
 
-struct dst_entry *__xfrm_dst_lookup(struct net *net, int tos, int oif,
-				    const xfrm_address_t *saddr,
-				    const xfrm_address_t *daddr,
-				    int family, u32 mark)
+struct dst_entry *__xfrm_dst_lookup(int family,
+				    const struct xfrm_dst_lookup_params *params)
 {
 	const struct xfrm_policy_afinfo *afinfo;
 	struct dst_entry *dst;
@@ -261,7 +261,7 @@
 	if (unlikely(afinfo == NULL))
 		return ERR_PTR(-EAFNOSUPPORT);
 
-	dst = afinfo->dst_lookup(net, tos, oif, saddr, daddr, mark);
+	dst = afinfo->dst_lookup(params);
 
 	rcu_read_unlock();
 
@@ -275,6 +275,7 @@
 						xfrm_address_t *prev_daddr,
 						int family, u32 mark)
 {
+	struct xfrm_dst_lookup_params params;
 	struct net *net = xs_net(x);
 	xfrm_address_t *saddr = &x->props.saddr;
 	xfrm_address_t *daddr = &x->id.daddr;
@@ -289,7 +290,29 @@
 		daddr = x->coaddr;
 	}
 
-	dst = __xfrm_dst_lookup(net, tos, oif, saddr, daddr, family, mark);
+	params.net = net;
+	params.saddr = saddr;
+	params.daddr = daddr;
+	params.tos = tos;
+	params.oif = oif;
+	params.mark = mark;
+	params.ipproto = x->id.proto;
+	if (x->encap) {
+		switch (x->encap->encap_type) {
+		case UDP_ENCAP_ESPINUDP:
+			params.ipproto = IPPROTO_UDP;
+			params.uli.ports.sport = x->encap->encap_sport;
+			params.uli.ports.dport = x->encap->encap_dport;
+			break;
+		case TCP_ENCAP_ESPINTCP:
+			params.ipproto = IPPROTO_TCP;
+			params.uli.ports.sport = x->encap->encap_sport;
+			params.uli.ports.dport = x->encap->encap_dport;
+			break;
+		}
+	}
+
+	dst = __xfrm_dst_lookup(family, &params);
 
 	if (!IS_ERR(dst)) {
 		if (prev_saddr != saddr)
@@ -1369,8 +1392,6 @@
  * of an absolute inpredictability of ordering of rules. This will not pass. */
 static u32 xfrm_gen_index(struct net *net, int dir, u32 index)
 {
-	static u32 idx_generator;
-
 	for (;;) {
 		struct hlist_head *list;
 		struct xfrm_policy *p;
@@ -1378,8 +1399,8 @@
 		int found;
 
 		if (!index) {
-			idx = (idx_generator | dir);
-			idx_generator += 8;
+			idx = (net->xfrm.idx_generator | dir);
+			net->xfrm.idx_generator += 8;
 		} else {
 			idx = index;
 			index = 0;
@@ -2342,15 +2363,15 @@
 }
 
 static int
-xfrm_get_saddr(struct net *net, int oif, xfrm_address_t *local,
-	       xfrm_address_t *remote, unsigned short family, u32 mark)
+xfrm_get_saddr(unsigned short family, xfrm_address_t *saddr,
+	       const struct xfrm_dst_lookup_params *params)
 {
 	int err;
 	const struct xfrm_policy_afinfo *afinfo = xfrm_policy_get_afinfo(family);
 
 	if (unlikely(afinfo == NULL))
 		return -EINVAL;
-	err = afinfo->get_saddr(net, oif, local, remote, mark);
+	err = afinfo->get_saddr(saddr, params);
 	rcu_read_unlock();
 	return err;
 }
@@ -2379,9 +2400,14 @@
 			remote = &tmpl->id.daddr;
 			local = &tmpl->saddr;
 			if (xfrm_addr_any(local, tmpl->encap_family)) {
-				error = xfrm_get_saddr(net, fl->flowi_oif,
-						       &tmp, remote,
-						       tmpl->encap_family, 0);
+				struct xfrm_dst_lookup_params params;
+
+				memset(&params, 0, sizeof(params));
+				params.net = net;
+				params.oif = fl->flowi_oif;
+				params.daddr = remote;
+				error = xfrm_get_saddr(tmpl->encap_family, &tmp,
+						       &params);
 				if (error)
 					goto fail;
 				local = &tmp;
@@ -2593,12 +2619,14 @@
 
 		if (xfrm[i]->props.mode != XFRM_MODE_TRANSPORT) {
 			__u32 mark = 0;
+			int oif;
 
 			if (xfrm[i]->props.smark.v || xfrm[i]->props.smark.m)
 				mark = xfrm_smark_get(fl->flowi_mark, xfrm[i]);
 
 			family = xfrm[i]->props.family;
-			dst = xfrm_dst_lookup(xfrm[i], tos, fl->flowi_oif,
+			oif = fl->flowi_oif ? : fl->flowi_l3mdev;
+			dst = xfrm_dst_lookup(xfrm[i], tos, oif,
 					      &saddr, &daddr, family, mark);
 			err = PTR_ERR(dst);
 			if (IS_ERR(dst))
@@ -2676,8 +2704,10 @@
 		*num_xfrms = 0;
 		return 0;
 	}
-	if (IS_ERR(pols[0]))
+	if (IS_ERR(pols[0])) {
+		*num_pols = 0;
 		return PTR_ERR(pols[0]);
+	}
 
 	*num_xfrms = pols[0]->xfrm_nr;
 
@@ -2692,6 +2722,7 @@
 		if (pols[1]) {
 			if (IS_ERR(pols[1])) {
 				xfrm_pols_put(pols, *num_pols);
+				*num_pols = 0;
 				return PTR_ERR(pols[1]);
 			}
 			(*num_pols)++;
@@ -3157,8 +3188,8 @@
 	return dst;
 
 nopol:
-	if (!(dst_orig->dev->flags & IFF_LOOPBACK) &&
-	    !xfrm_default_allow(net, dir)) {
+	if ((!dst_orig->dev || !(dst_orig->dev->flags & IFF_LOOPBACK)) &&
+	    net->xfrm.policy_default[dir] == XFRM_USERPOLICY_BLOCK) {
 		err = -EPERM;
 		goto error;
 	}
@@ -3233,7 +3264,7 @@
 
 static inline int
 xfrm_state_ok(const struct xfrm_tmpl *tmpl, const struct xfrm_state *x,
-	      unsigned short family)
+	      unsigned short family, u32 if_id)
 {
 	if (xfrm_state_kern(x))
 		return tmpl->optional && !xfrm_state_addr_cmp(tmpl, x, tmpl->encap_family);
@@ -3244,7 +3275,8 @@
 		(tmpl->allalgs || (tmpl->aalgos & (1<<x->props.aalgo)) ||
 		 !(xfrm_id_proto_match(tmpl->id.proto, IPSEC_PROTO_ANY))) &&
 		!(x->props.mode != XFRM_MODE_TRANSPORT &&
-		  xfrm_state_addr_cmp(tmpl, x, family));
+		  xfrm_state_addr_cmp(tmpl, x, family)) &&
+		(if_id == 0 || if_id == x->if_id);
 }
 
 /*
@@ -3256,7 +3288,7 @@
  */
 static inline int
 xfrm_policy_ok(const struct xfrm_tmpl *tmpl, const struct sec_path *sp, int start,
-	       unsigned short family)
+	       unsigned short family, u32 if_id)
 {
 	int idx = start;
 
@@ -3266,9 +3298,16 @@
 	} else
 		start = -1;
 	for (; idx < sp->len; idx++) {
-		if (xfrm_state_ok(tmpl, sp->xvec[idx], family))
+		if (xfrm_state_ok(tmpl, sp->xvec[idx], family, if_id))
 			return ++idx;
 		if (sp->xvec[idx]->props.mode != XFRM_MODE_TRANSPORT) {
+			if (idx < sp->verified_cnt) {
+				/* Secpath entry previously verified, consider optional and
+				 * continue searching
+				 */
+				continue;
+			}
+
 			if (start == -1)
 				start = -2-idx;
 			break;
@@ -3296,7 +3335,7 @@
 	fl4->flowi4_proto = iph->protocol;
 	fl4->daddr = reverse ? iph->saddr : iph->daddr;
 	fl4->saddr = reverse ? iph->daddr : iph->saddr;
-	fl4->flowi4_tos = iph->tos;
+	fl4->flowi4_tos = iph->tos & ~INET_ECN_MASK;
 
 	if (!ip_is_fragment(iph)) {
 		switch (iph->protocol) {
@@ -3424,6 +3463,26 @@
 			}
 			fl6->flowi6_proto = nexthdr;
 			return;
+		case IPPROTO_GRE:
+			if (!onlyproto &&
+			    (nh + offset + 12 < skb->data ||
+			     pskb_may_pull(skb, nh + offset + 12 - skb->data))) {
+				struct gre_base_hdr *gre_hdr;
+				__be32 *gre_key;
+
+				nh = skb_network_header(skb);
+				gre_hdr = (struct gre_base_hdr *)(nh + offset);
+				gre_key = (__be32 *)(gre_hdr + 1);
+
+				if (gre_hdr->flags & GRE_KEY) {
+					if (gre_hdr->flags & GRE_CSUM)
+						gre_key++;
+					fl6->fl6_gre_key = *gre_key;
+				}
+			}
+			fl6->flowi6_proto = nexthdr;
+			return;
+
 #if IS_ENABLED(CONFIG_IPV6_MIP6)
 		case IPPROTO_MH:
 			offset += ipv6_optlen(exthdr);
@@ -3550,7 +3609,7 @@
 	}
 
 	if (!pol) {
-		if (!xfrm_default_allow(net, dir)) {
+		if (net->xfrm.policy_default[dir] == XFRM_USERPOLICY_BLOCK) {
 			XFRM_INC_STATS(net, LINUX_MIB_XFRMINNOPOLS);
 			return 0;
 		}
@@ -3575,6 +3634,7 @@
 		if (pols[1]) {
 			if (IS_ERR(pols[1])) {
 				XFRM_INC_STATS(net, LINUX_MIB_XFRMINPOLERROR);
+				xfrm_pol_put(pols[0]);
 				return 0;
 			}
 			pols[1]->curlft.use_time = ktime_get_real_seconds();
@@ -3610,11 +3670,6 @@
 		}
 		xfrm_nr = ti;
 
-		if (!xfrm_default_allow(net, dir) && !xfrm_nr) {
-			XFRM_INC_STATS(net, LINUX_MIB_XFRMINNOSTATES);
-			goto reject;
-		}
-
 		if (npols > 1) {
 			xfrm_tmpl_sort(stp, tpp, xfrm_nr, family);
 			tpp = stp;
@@ -3625,9 +3680,12 @@
 		 * Order is _important_. Later we will implement
 		 * some barriers, but at the moment barriers
 		 * are implied between each two transformations.
+		 * Upon success, marks secpath entries as having been
+		 * verified to allow them to be skipped in future policy
+		 * checks (e.g. nested tunnels).
 		 */
 		for (i = xfrm_nr-1, k = 0; i >= 0; i--) {
-			k = xfrm_policy_ok(tpp[i], sp, k, family);
+			k = xfrm_policy_ok(tpp[i], sp, k, family, if_id);
 			if (k < 0) {
 				if (k < -1)
 					/* "-2 - errored_index" returned */
@@ -3643,6 +3701,8 @@
 		}
 
 		xfrm_pols_put(pols, npols);
+		sp->verified_cnt = k;
+
 		return 1;
 	}
 	XFRM_INC_STATS(net, LINUX_MIB_XFRMINPOLBLOCK);
@@ -3734,15 +3794,10 @@
 	/* Impossible. Such dst must be popped before reaches point of failure. */
 }
 
-static struct dst_entry *xfrm_negative_advice(struct dst_entry *dst)
+static void xfrm_negative_advice(struct sock *sk, struct dst_entry *dst)
 {
-	if (dst) {
-		if (dst->obsolete) {
-			dst_release(dst);
-			dst = NULL;
-		}
-	}
-	return dst;
+	if (dst->obsolete)
+		sk_dst_reset(sk);
 }
 
 static void xfrm_init_pmtu(struct xfrm_dst **bundle, int nr)
@@ -4099,6 +4154,9 @@
 	spin_lock_init(&net->xfrm.xfrm_policy_lock);
 	seqcount_spinlock_init(&net->xfrm.xfrm_policy_hash_generation, &net->xfrm.xfrm_policy_lock);
 	mutex_init(&net->xfrm.xfrm_cfg_mutex);
+	net->xfrm.policy_default[XFRM_POLICY_IN] = XFRM_USERPOLICY_ACCEPT;
+	net->xfrm.policy_default[XFRM_POLICY_FWD] = XFRM_USERPOLICY_ACCEPT;
+	net->xfrm.policy_default[XFRM_POLICY_OUT] = XFRM_USERPOLICY_ACCEPT;
 
 	rv = xfrm_statistics_init(net);
 	if (rv < 0)
@@ -4237,7 +4295,7 @@
 }
 
 static struct xfrm_policy *xfrm_migrate_policy_find(const struct xfrm_selector *sel,
-						    u8 dir, u8 type, struct net *net)
+						    u8 dir, u8 type, struct net *net, u32 if_id)
 {
 	struct xfrm_policy *pol, *ret = NULL;
 	struct hlist_head *chain;
@@ -4246,7 +4304,8 @@
 	spin_lock_bh(&net->xfrm.xfrm_policy_lock);
 	chain = policy_hash_direct(net, &sel->daddr, &sel->saddr, sel->family, dir);
 	hlist_for_each_entry(pol, chain, bydst) {
-		if (xfrm_migrate_selector_match(sel, &pol->selector) &&
+		if ((if_id == 0 || pol->if_id == if_id) &&
+		    xfrm_migrate_selector_match(sel, &pol->selector) &&
 		    pol->type == type) {
 			ret = pol;
 			priority = ret->priority;
@@ -4258,7 +4317,8 @@
 		if ((pol->priority >= priority) && ret)
 			break;
 
-		if (xfrm_migrate_selector_match(sel, &pol->selector) &&
+		if ((if_id == 0 || pol->if_id == if_id) &&
+		    xfrm_migrate_selector_match(sel, &pol->selector) &&
 		    pol->type == type) {
 			ret = pol;
 			break;
@@ -4374,7 +4434,7 @@
 int xfrm_migrate(const struct xfrm_selector *sel, u8 dir, u8 type,
 		 struct xfrm_migrate *m, int num_migrate,
 		 struct xfrm_kmaddress *k, struct net *net,
-		 struct xfrm_encap_tmpl *encap)
+		 struct xfrm_encap_tmpl *encap, u32 if_id)
 {
 	int i, err, nx_cur = 0, nx_new = 0;
 	struct xfrm_policy *pol = NULL;
@@ -4393,14 +4453,14 @@
 	}
 
 	/* Stage 1 - find policy */
-	if ((pol = xfrm_migrate_policy_find(sel, dir, type, net)) == NULL) {
+	if ((pol = xfrm_migrate_policy_find(sel, dir, type, net, if_id)) == NULL) {
 		err = -ENOENT;
 		goto out;
 	}
 
 	/* Stage 2 - find and update state(s) */
 	for (i = 0, mp = m; i < num_migrate; i++, mp++) {
-		if ((x = xfrm_migrate_state_find(mp, net))) {
+		if ((x = xfrm_migrate_state_find(mp, net, if_id))) {
 			x_cur[nx_cur] = x;
 			nx_cur++;
 			xc = xfrm_state_migrate(x, mp, encap);
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_replay.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_replay.c
@@ -715,9 +715,11 @@
 		}
 
 		if (unlikely(oseq < replay_esn->oseq)) {
-			XFRM_SKB_CB(skb)->seq.output.hi = ++oseq_hi;
-			xo->seq.hi = oseq_hi;
-			replay_esn->oseq_hi = oseq_hi;
+			replay_esn->oseq_hi = ++oseq_hi;
+			if (xo->seq.low < replay_esn->oseq) {
+				XFRM_SKB_CB(skb)->seq.output.hi = oseq_hi;
+				xo->seq.hi = oseq_hi;
+			}
 			if (replay_esn->oseq_hi == 0) {
 				replay_esn->oseq--;
 				replay_esn->oseq_hi--;
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_state.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_state.c
@@ -750,7 +750,7 @@
 
 	for (i = 0; i <= net->xfrm.state_hmask; i++) {
 		struct xfrm_state *x;
-		struct xfrm_state_offload *xso;
+		struct xfrm_dev_offload *xso;
 
 		hlist_for_each_entry(x, net->xfrm.state_bydst+i, bydst) {
 			xso = &x->xso;
@@ -834,7 +834,7 @@
 	err = -ESRCH;
 	for (i = 0; i <= net->xfrm.state_hmask; i++) {
 		struct xfrm_state *x;
-		struct xfrm_state_offload *xso;
+		struct xfrm_dev_offload *xso;
 restart:
 		hlist_for_each_entry(x, net->xfrm.state_bydst+i, bydst) {
 			xso = &x->xso;
@@ -1578,9 +1578,6 @@
 	memcpy(&x->mark, &orig->mark, sizeof(x->mark));
 	memcpy(&x->props.smark, &orig->props.smark, sizeof(x->props.smark));
 
-	if (xfrm_init_state(x) < 0)
-		goto error;
-
 	x->props.flags = orig->props.flags;
 	x->props.extra_flags = orig->props.extra_flags;
 
@@ -1593,6 +1590,10 @@
 	x->km.seq = orig->km.seq;
 	x->replay = orig->replay;
 	x->preplay = orig->preplay;
+	x->mapping_maxage = orig->mapping_maxage;
+	x->lastused = orig->lastused;
+	x->new_mapping = 0;
+	x->new_mapping_sport = 0;
 
 	return x;
 
@@ -1602,7 +1603,8 @@
 	return NULL;
 }
 
-struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net)
+struct xfrm_state *xfrm_migrate_state_find(struct xfrm_migrate *m, struct net *net,
+						u32 if_id)
 {
 	unsigned int h;
 	struct xfrm_state *x = NULL;
@@ -1618,6 +1620,8 @@
 				continue;
 			if (m->reqid && x->props.reqid != m->reqid)
 				continue;
+			if (if_id != 0 && x->if_id != if_id)
+				continue;
 			if (!xfrm_addr_equal(&x->id.daddr, &m->old_daddr,
 					     m->old_family) ||
 			    !xfrm_addr_equal(&x->props.saddr, &m->old_saddr,
@@ -1633,6 +1637,8 @@
 			if (x->props.mode != m->mode ||
 			    x->id.proto != m->proto)
 				continue;
+			if (if_id != 0 && x->if_id != if_id)
+				continue;
 			if (!xfrm_addr_equal(&x->id.daddr, &m->old_daddr,
 					     m->old_family) ||
 			    !xfrm_addr_equal(&x->props.saddr, &m->old_saddr,
@@ -1659,6 +1665,11 @@
 	if (!xc)
 		return NULL;
 
+	xc->props.family = m->new_family;
+
+	if (xfrm_init_state(xc) < 0)
+		goto error;
+
 	memcpy(&xc->id.daddr, &m->new_daddr, sizeof(xc->id.daddr));
 	memcpy(&xc->props.saddr, &m->new_saddr, sizeof(xc->props.saddr));
 
@@ -2242,7 +2253,7 @@
 }
 EXPORT_SYMBOL(km_query);
 
-int km_new_mapping(struct xfrm_state *x, xfrm_address_t *ipaddr, __be16 sport)
+static int __km_new_mapping(struct xfrm_state *x, xfrm_address_t *ipaddr, __be16 sport)
 {
 	int err = -EINVAL;
 	struct xfrm_mgr *km;
@@ -2257,6 +2268,24 @@
 	rcu_read_unlock();
 	return err;
 }
+
+int km_new_mapping(struct xfrm_state *x, xfrm_address_t *ipaddr, __be16 sport)
+{
+	int ret = 0;
+
+	if (x->mapping_maxage) {
+		if ((jiffies / HZ - x->new_mapping) > x->mapping_maxage ||
+		    x->new_mapping_sport != sport) {
+			x->new_mapping_sport = sport;
+			x->new_mapping = jiffies / HZ;
+			ret = __km_new_mapping(x, ipaddr, sport);
+		}
+	} else {
+		ret = __km_new_mapping(x, ipaddr, sport);
+	}
+
+	return ret;
+}
 EXPORT_SYMBOL(km_new_mapping);
 
 void km_policy_expired(struct xfrm_policy *pol, int dir, int hard, u32 portid)
@@ -2550,7 +2579,7 @@
 }
 EXPORT_SYMBOL(xfrm_state_delete_tunnel);
 
-u32 __xfrm_state_mtu(struct xfrm_state *x, int mtu)
+u32 xfrm_state_mtu(struct xfrm_state *x, int mtu)
 {
 	const struct xfrm_type *type = READ_ONCE(x->type);
 	struct crypto_aead *aead;
@@ -2581,17 +2610,7 @@
 	return ((mtu - x->props.header_len - crypto_aead_authsize(aead) -
 		 net_adj) & ~(blksize - 1)) + net_adj - 2;
 }
-EXPORT_SYMBOL_GPL(__xfrm_state_mtu);
-
-u32 xfrm_state_mtu(struct xfrm_state *x, int mtu)
-{
-	mtu = __xfrm_state_mtu(x, mtu);
-
-	if (x->props.family == AF_INET6 && mtu < IPV6_MIN_MTU)
-		return IPV6_MIN_MTU;
-
-	return mtu;
-}
+EXPORT_SYMBOL_GPL(xfrm_state_mtu);
 
 int __xfrm_init_state(struct xfrm_state *x, bool init_replay, bool offload)
 {
@@ -2601,7 +2620,7 @@
 	int err;
 
 	if (family == AF_INET &&
-	    xs_net(x)->ipv4.sysctl_ip_no_pmtu_disc)
+	    READ_ONCE(xs_net(x)->ipv4.sysctl_ip_no_pmtu_disc))
 		x->props.flags |= XFRM_STATE_NOPMTUDISC;
 
 	err = -EPROTONOSUPPORT;
@@ -2624,9 +2643,6 @@
 		if (inner_mode == NULL)
 			goto error;
 
-		if (!(inner_mode->flags & XFRM_MODE_FLAG_TUNNEL))
-			goto error;
-
 		x->inner_mode = *inner_mode;
 
 		if (x->props.family == AF_INET)
--- linux-xilinx-zynqmp-5.15.0.orig/net/xfrm/xfrm_user.c
+++ linux-xilinx-zynqmp-5.15.0/net/xfrm/xfrm_user.c
@@ -149,6 +149,7 @@
 			     struct nlattr **attrs)
 {
 	int err;
+	u16 family = p->sel.family;
 
 	err = -EINVAL;
 	switch (p->family) {
@@ -167,7 +168,10 @@
 		goto out;
 	}
 
-	switch (p->sel.family) {
+	if (!family && !(p->flags & XFRM_STATE_AF_UNSPEC))
+		family = p->family;
+
+	switch (family) {
 	case AF_UNSPEC:
 		break;
 
@@ -282,6 +286,10 @@
 
 	err = 0;
 
+	if (attrs[XFRMA_MTIMER_THRESH])
+		if (!attrs[XFRMA_ENCAP])
+			err = -EINVAL;
+
 out:
 	return err;
 }
@@ -521,8 +529,9 @@
 	struct nlattr *lt = attrs[XFRMA_LTIME_VAL];
 	struct nlattr *et = attrs[XFRMA_ETIMER_THRESH];
 	struct nlattr *rt = attrs[XFRMA_REPLAY_THRESH];
+	struct nlattr *mt = attrs[XFRMA_MTIMER_THRESH];
 
-	if (re) {
+	if (re && x->replay_esn && x->preplay_esn) {
 		struct xfrm_replay_state_esn *replay_esn;
 		replay_esn = nla_data(re);
 		memcpy(x->replay_esn, replay_esn,
@@ -552,6 +561,9 @@
 
 	if (rt)
 		x->replay_maxdiff = nla_get_u32(rt);
+
+	if (mt)
+		x->mapping_maxage = nla_get_u32(mt);
 }
 
 static void xfrm_smark_init(struct nlattr **attrs, struct xfrm_mark *m)
@@ -831,7 +843,7 @@
 	return 0;
 }
 
-static int copy_user_offload(struct xfrm_state_offload *xso, struct sk_buff *skb)
+static int copy_user_offload(struct xfrm_dev_offload *xso, struct sk_buff *skb)
 {
 	struct xfrm_user_offload *xuo;
 	struct nlattr *attr;
@@ -843,7 +855,8 @@
 	xuo = nla_data(attr);
 	memset(xuo, 0, sizeof(*xuo));
 	xuo->ifindex = xso->dev->ifindex;
-	xuo->flags = xso->flags;
+	if (xso->dir == XFRM_DEV_OFFLOAD_IN)
+		xuo->flags = XFRM_OFFLOAD_INBOUND;
 
 	return 0;
 }
@@ -879,7 +892,9 @@
 	if (!nla)
 		return -EMSGSIZE;
 	ap = nla_data(nla);
-	memcpy(ap, auth, sizeof(struct xfrm_algo_auth));
+	strscpy_pad(ap->alg_name, auth->alg_name, sizeof(ap->alg_name));
+	ap->alg_key_len = auth->alg_key_len;
+	ap->alg_trunc_len = auth->alg_trunc_len;
 	if (redact_secret && auth->alg_key_len)
 		memset(ap->alg_key, 0, (auth->alg_key_len + 7) / 8);
 	else
@@ -898,7 +913,9 @@
 		return -EMSGSIZE;
 
 	ap = nla_data(nla);
-	memcpy(ap, aead, sizeof(*aead));
+	strscpy_pad(ap->alg_name, aead->alg_name, sizeof(ap->alg_name));
+	ap->alg_key_len = aead->alg_key_len;
+	ap->alg_icv_len = aead->alg_icv_len;
 
 	if (redact_secret && aead->alg_key_len)
 		memset(ap->alg_key, 0, (aead->alg_key_len + 7) / 8);
@@ -918,7 +935,8 @@
 		return -EMSGSIZE;
 
 	ap = nla_data(nla);
-	memcpy(ap, ealg, sizeof(*ealg));
+	strscpy_pad(ap->alg_name, ealg->alg_name, sizeof(ap->alg_name));
+	ap->alg_key_len = ealg->alg_key_len;
 
 	if (redact_secret && ealg->alg_key_len)
 		memset(ap->alg_key, 0, (ealg->alg_key_len + 7) / 8);
@@ -929,6 +947,40 @@
 	return 0;
 }
 
+static int copy_to_user_calg(struct xfrm_algo *calg, struct sk_buff *skb)
+{
+	struct nlattr *nla = nla_reserve(skb, XFRMA_ALG_COMP, sizeof(*calg));
+	struct xfrm_algo *ap;
+
+	if (!nla)
+		return -EMSGSIZE;
+
+	ap = nla_data(nla);
+	strscpy_pad(ap->alg_name, calg->alg_name, sizeof(ap->alg_name));
+	ap->alg_key_len = 0;
+
+	return 0;
+}
+
+static int copy_to_user_encap(struct xfrm_encap_tmpl *ep, struct sk_buff *skb)
+{
+	struct nlattr *nla = nla_reserve(skb, XFRMA_ENCAP, sizeof(*ep));
+	struct xfrm_encap_tmpl *uep;
+
+	if (!nla)
+		return -EMSGSIZE;
+
+	uep = nla_data(nla);
+	memset(uep, 0, sizeof(*uep));
+
+	uep->encap_type = ep->encap_type;
+	uep->encap_sport = ep->encap_sport;
+	uep->encap_dport = ep->encap_dport;
+	uep->encap_oa = ep->encap_oa;
+
+	return 0;
+}
+
 static int xfrm_smark_put(struct sk_buff *skb, struct xfrm_mark *m)
 {
 	int ret = 0;
@@ -984,12 +1036,12 @@
 			goto out;
 	}
 	if (x->calg) {
-		ret = nla_put(skb, XFRMA_ALG_COMP, sizeof(*(x->calg)), x->calg);
+		ret = copy_to_user_calg(x->calg, skb);
 		if (ret)
 			goto out;
 	}
 	if (x->encap) {
-		ret = nla_put(skb, XFRMA_ENCAP, sizeof(*x->encap), x->encap);
+		ret = copy_to_user_encap(x->encap, skb);
 		if (ret)
 			goto out;
 	}
@@ -1024,8 +1076,13 @@
 		if (ret)
 			goto out;
 	}
-	if (x->security)
+	if (x->security) {
 		ret = copy_sec_ctx(x->security, skb);
+		if (ret)
+			goto out;
+	}
+	if (x->mapping_maxage)
+		ret = nla_put_u32(skb, XFRMA_MTIMER_THRESH, x->mapping_maxage);
 out:
 	return ret;
 }
@@ -1109,6 +1166,15 @@
 					 sizeof(*filter), GFP_KERNEL);
 			if (filter == NULL)
 				return -ENOMEM;
+
+			/* see addr_match(), (prefix length >> 5) << 2
+			 * will be used to compare xfrm_address_t
+			 */
+			if (filter->splen > (sizeof(xfrm_address_t) << 3) ||
+			    filter->dplen > (sizeof(xfrm_address_t) << 3)) {
+				kfree(filter);
+				return -EINVAL;
+			}
 		}
 
 		if (attrs[XFRMA_PROTO])
@@ -1791,6 +1857,9 @@
 	if (xp->xfrm_nr == 0)
 		return 0;
 
+	if (xp->xfrm_nr > XFRM_MAX_DEPTH)
+		return -ENOBUFS;
+
 	for (i = 0; i < xp->xfrm_nr; i++) {
 		struct xfrm_user_tmpl *up = &vec[i];
 		struct xfrm_tmpl *kp = &xp->xfrm_vec[i];
@@ -1980,12 +2049,9 @@
 	}
 
 	up = nlmsg_data(nlh);
-	up->in = net->xfrm.policy_default & XFRM_POL_DEFAULT_IN ?
-			XFRM_USERPOLICY_BLOCK : XFRM_USERPOLICY_ACCEPT;
-	up->fwd = net->xfrm.policy_default & XFRM_POL_DEFAULT_FWD ?
-			XFRM_USERPOLICY_BLOCK : XFRM_USERPOLICY_ACCEPT;
-	up->out = net->xfrm.policy_default & XFRM_POL_DEFAULT_OUT ?
-			XFRM_USERPOLICY_BLOCK : XFRM_USERPOLICY_ACCEPT;
+	up->in = net->xfrm.policy_default[XFRM_POLICY_IN];
+	up->fwd = net->xfrm.policy_default[XFRM_POLICY_FWD];
+	up->out = net->xfrm.policy_default[XFRM_POLICY_OUT];
 
 	nlmsg_end(skb, nlh);
 
@@ -1996,26 +2062,26 @@
 	return err;
 }
 
+static bool xfrm_userpolicy_is_valid(__u8 policy)
+{
+	return policy == XFRM_USERPOLICY_BLOCK ||
+	       policy == XFRM_USERPOLICY_ACCEPT;
+}
+
 static int xfrm_set_default(struct sk_buff *skb, struct nlmsghdr *nlh,
 			    struct nlattr **attrs)
 {
 	struct net *net = sock_net(skb->sk);
 	struct xfrm_userpolicy_default *up = nlmsg_data(nlh);
 
-	if (up->in == XFRM_USERPOLICY_BLOCK)
-		net->xfrm.policy_default |= XFRM_POL_DEFAULT_IN;
-	else if (up->in == XFRM_USERPOLICY_ACCEPT)
-		net->xfrm.policy_default &= ~XFRM_POL_DEFAULT_IN;
-
-	if (up->fwd == XFRM_USERPOLICY_BLOCK)
-		net->xfrm.policy_default |= XFRM_POL_DEFAULT_FWD;
-	else if (up->fwd == XFRM_USERPOLICY_ACCEPT)
-		net->xfrm.policy_default &= ~XFRM_POL_DEFAULT_FWD;
-
-	if (up->out == XFRM_USERPOLICY_BLOCK)
-		net->xfrm.policy_default |= XFRM_POL_DEFAULT_OUT;
-	else if (up->out == XFRM_USERPOLICY_ACCEPT)
-		net->xfrm.policy_default &= ~XFRM_POL_DEFAULT_OUT;
+	if (xfrm_userpolicy_is_valid(up->in))
+		net->xfrm.policy_default[XFRM_POLICY_IN] = up->in;
+
+	if (xfrm_userpolicy_is_valid(up->fwd))
+		net->xfrm.policy_default[XFRM_POLICY_FWD] = up->fwd;
+
+	if (xfrm_userpolicy_is_valid(up->out))
+		net->xfrm.policy_default[XFRM_POLICY_OUT] = up->out;
 
 	rt_genid_bump_all(net);
 
@@ -2045,13 +2111,9 @@
 	}
 
 	r_up = nlmsg_data(r_nlh);
-
-	r_up->in = net->xfrm.policy_default & XFRM_POL_DEFAULT_IN ?
-			XFRM_USERPOLICY_BLOCK : XFRM_USERPOLICY_ACCEPT;
-	r_up->fwd = net->xfrm.policy_default & XFRM_POL_DEFAULT_FWD ?
-			XFRM_USERPOLICY_BLOCK : XFRM_USERPOLICY_ACCEPT;
-	r_up->out = net->xfrm.policy_default & XFRM_POL_DEFAULT_OUT ?
-			XFRM_USERPOLICY_BLOCK : XFRM_USERPOLICY_ACCEPT;
+	r_up->in = net->xfrm.policy_default[XFRM_POLICY_IN];
+	r_up->fwd = net->xfrm.policy_default[XFRM_POLICY_FWD];
+	r_up->out = net->xfrm.policy_default[XFRM_POLICY_OUT];
 	nlmsg_end(r_skb, r_nlh);
 
 	return nlmsg_unicast(net->xfrm.nlsk, r_skb, portid);
@@ -2579,6 +2641,7 @@
 	int n = 0;
 	struct net *net = sock_net(skb->sk);
 	struct xfrm_encap_tmpl  *encap = NULL;
+	u32 if_id = 0;
 
 	if (attrs[XFRMA_MIGRATE] == NULL)
 		return -EINVAL;
@@ -2603,7 +2666,10 @@
 			return -ENOMEM;
 	}
 
-	err = xfrm_migrate(&pi->sel, pi->dir, type, m, n, kmp, net, encap);
+	if (attrs[XFRMA_IF_ID])
+		if_id = nla_get_u32(attrs[XFRMA_IF_ID]);
+
+	err = xfrm_migrate(&pi->sel, pi->dir, type, m, n, kmp, net, encap, if_id);
 
 	kfree(encap);
 
@@ -2778,7 +2844,7 @@
 	[XFRMA_ALG_COMP]	= { .len = sizeof(struct xfrm_algo) },
 	[XFRMA_ENCAP]		= { .len = sizeof(struct xfrm_encap_tmpl) },
 	[XFRMA_TMPL]		= { .len = sizeof(struct xfrm_user_tmpl) },
-	[XFRMA_SEC_CTX]		= { .len = sizeof(struct xfrm_sec_ctx) },
+	[XFRMA_SEC_CTX]		= { .len = sizeof(struct xfrm_user_sec_ctx) },
 	[XFRMA_LTIME_VAL]	= { .len = sizeof(struct xfrm_lifetime_cur) },
 	[XFRMA_REPLAY_VAL]	= { .len = sizeof(struct xfrm_replay_state) },
 	[XFRMA_REPLAY_THRESH]	= { .type = NLA_U32 },
@@ -2798,6 +2864,7 @@
 	[XFRMA_SET_MARK]	= { .type = NLA_U32 },
 	[XFRMA_SET_MARK_MASK]	= { .type = NLA_U32 },
 	[XFRMA_IF_ID]		= { .type = NLA_U32 },
+	[XFRMA_MTIMER_THRESH]   = { .type = NLA_U32 },
 };
 EXPORT_SYMBOL_GPL(xfrma_policy);
 
@@ -3058,7 +3125,7 @@
 	if (x->props.extra_flags)
 		l += nla_total_size(sizeof(x->props.extra_flags));
 	if (x->xso.dev)
-		 l += nla_total_size(sizeof(x->xso));
+		 l += nla_total_size(sizeof(struct xfrm_user_offload));
 	if (x->props.smark.v | x->props.smark.m) {
 		l += nla_total_size(sizeof(x->props.smark.v));
 		l += nla_total_size(sizeof(x->props.smark.m));
@@ -3069,6 +3136,9 @@
 	/* Must count x->lastused as it may become non-zero behind our back. */
 	l += nla_total_size_64bit(sizeof(u64));
 
+	if (x->mapping_maxage)
+		l += nla_total_size(sizeof(x->mapping_maxage));
+
 	return l;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/samples/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/samples/Kconfig
@@ -120,6 +120,15 @@
 	  with it.
 	  See also Documentation/driver-api/connector.rst
 
+config SAMPLE_FANOTIFY_ERROR
+	bool "Build fanotify error monitoring sample"
+	depends on FANOTIFY && CC_CAN_LINK && HEADERS_INSTALL
+	help
+	  When enabled, this builds an example code that uses the
+	  FAN_FS_ERROR fanotify mechanism to monitor filesystem
+	  errors.
+	  See also Documentation/admin-guide/filesystem-monitoring.rst.
+
 config SAMPLE_HIDRAW
 	bool "hidraw sample"
 	depends on CC_CAN_LINK && HEADERS_INSTALL
--- linux-xilinx-zynqmp-5.15.0.orig/samples/Makefile
+++ linux-xilinx-zynqmp-5.15.0/samples/Makefile
@@ -5,6 +5,7 @@
 subdir-$(CONFIG_SAMPLE_ANDROID_BINDERFS) += binderfs
 obj-$(CONFIG_SAMPLE_CONFIGFS)		+= configfs/
 obj-$(CONFIG_SAMPLE_CONNECTOR)		+= connector/
+obj-$(CONFIG_SAMPLE_FANOTIFY_ERROR)	+= fanotify/
 subdir-$(CONFIG_SAMPLE_HIDRAW)		+= hidraw
 obj-$(CONFIG_SAMPLE_HW_BREAKPOINT)	+= hw_breakpoint/
 obj-$(CONFIG_SAMPLE_KDB)		+= kdb/
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/Makefile
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/Makefile
@@ -59,7 +59,11 @@
 tprogs-y += xdp_monitor
 
 # Libbpf dependencies
-LIBBPF = $(TOOLS_PATH)/lib/bpf/libbpf.a
+LIBBPF_SRC = $(TOOLS_PATH)/lib/bpf
+LIBBPF_OUTPUT = $(abspath $(BPF_SAMPLES_PATH))/libbpf
+LIBBPF_DESTDIR = $(LIBBPF_OUTPUT)
+LIBBPF_INCLUDE = $(LIBBPF_DESTDIR)/include
+LIBBPF = $(LIBBPF_OUTPUT)/libbpf.a
 
 CGROUP_HELPERS := ../../tools/testing/selftests/bpf/cgroup_helpers.o
 TRACE_HELPERS := ../../tools/testing/selftests/bpf/trace_helpers.o
@@ -198,7 +202,7 @@
 
 TPROGS_CFLAGS += -I$(objtree)/usr/include
 TPROGS_CFLAGS += -I$(srctree)/tools/testing/selftests/bpf/
-TPROGS_CFLAGS += -I$(srctree)/tools/lib/
+TPROGS_CFLAGS += -I$(LIBBPF_INCLUDE)
 TPROGS_CFLAGS += -I$(srctree)/tools/include
 TPROGS_CFLAGS += -I$(srctree)/tools/perf
 TPROGS_CFLAGS += -DHAVE_ATTR_TEST=0
@@ -209,6 +213,11 @@
 endif
 
 TPROGS_LDLIBS			+= $(LIBBPF) -lelf -lz
+TPROGLDLIBS_xdp_monitor		+= -lm
+TPROGLDLIBS_xdp_redirect	+= -lm
+TPROGLDLIBS_xdp_redirect_cpu	+= -lm
+TPROGLDLIBS_xdp_redirect_map	+= -lm
+TPROGLDLIBS_xdp_redirect_map_multi += -lm
 TPROGLDLIBS_tracex4		+= -lrt
 TPROGLDLIBS_trace_output	+= -lrt
 TPROGLDLIBS_map_perf_test	+= -lrt
@@ -268,16 +277,27 @@
 clean:
 	$(MAKE) -C ../../ M=$(CURDIR) clean
 	@find $(CURDIR) -type f -name '*~' -delete
+	@$(RM) -r $(CURDIR)/libbpf $(CURDIR)/bpftool
 
-$(LIBBPF): FORCE
+$(LIBBPF): FORCE | $(LIBBPF_OUTPUT)
 # Fix up variables inherited from Kbuild that tools/ build system won't like
-	$(MAKE) -C $(dir $@) RM='rm -rf' EXTRA_CFLAGS="$(TPROGS_CFLAGS)" \
-		LDFLAGS=$(TPROGS_LDFLAGS) srctree=$(BPF_SAMPLES_PATH)/../../ O=
+	$(MAKE) -C $(LIBBPF_SRC) RM='rm -rf' EXTRA_CFLAGS="$(TPROGS_CFLAGS)" \
+		LDFLAGS=$(TPROGS_LDFLAGS) srctree=$(BPF_SAMPLES_PATH)/../../ \
+		O= OUTPUT=$(LIBBPF_OUTPUT)/ DESTDIR=$(LIBBPF_DESTDIR) prefix= \
+		$@ install_headers
 
 BPFTOOLDIR := $(TOOLS_PATH)/bpf/bpftool
-BPFTOOL := $(BPFTOOLDIR)/bpftool
-$(BPFTOOL): $(wildcard $(BPFTOOLDIR)/*.[ch] $(BPFTOOLDIR)/Makefile)
-	    $(MAKE) -C $(BPFTOOLDIR) srctree=$(BPF_SAMPLES_PATH)/../../
+BPFTOOL_OUTPUT := $(abspath $(BPF_SAMPLES_PATH))/bpftool
+BPFTOOL := $(BPFTOOL_OUTPUT)/bpftool
+$(BPFTOOL): $(LIBBPF) $(wildcard $(BPFTOOLDIR)/*.[ch] $(BPFTOOLDIR)/Makefile) | $(BPFTOOL_OUTPUT)
+	    $(MAKE) -C $(BPFTOOLDIR) srctree=$(BPF_SAMPLES_PATH)/../../ \
+		OUTPUT=$(BPFTOOL_OUTPUT)/ \
+		LIBBPF_OUTPUT=$(LIBBPF_OUTPUT)/ \
+		LIBBPF_DESTDIR=$(LIBBPF_DESTDIR)/
+
+$(LIBBPF_OUTPUT) $(BPFTOOL_OUTPUT):
+	$(call msg,MKDIR,$@)
+	$(Q)mkdir -p $@
 
 $(obj)/syscall_nrs.h:	$(obj)/syscall_nrs.s FORCE
 	$(call filechk,offsets,__SYSCALL_NRS_H__)
@@ -309,6 +329,11 @@
 $(BPF_SAMPLES_PATH)/*.c: verify_target_bpf $(LIBBPF)
 $(src)/*.c: verify_target_bpf $(LIBBPF)
 
+libbpf_hdrs: $(LIBBPF)
+$(obj)/$(TRACE_HELPERS) $(obj)/$(CGROUP_HELPERS) $(obj)/$(XDP_SAMPLE): | libbpf_hdrs
+
+.PHONY: libbpf_hdrs
+
 $(obj)/xdp_redirect_cpu_user.o: $(obj)/xdp_redirect_cpu.skel.h
 $(obj)/xdp_redirect_map_multi_user.o: $(obj)/xdp_redirect_map_multi.skel.h
 $(obj)/xdp_redirect_map_user.o: $(obj)/xdp_redirect_map.skel.h
@@ -320,6 +345,17 @@
 $(obj)/hbm.o: $(src)/hbm.h
 $(obj)/hbm_edt_kern.o: $(src)/hbm.h $(src)/hbm_kern.h
 
+# Override includes for xdp_sample_user.o because $(srctree)/usr/include in
+# TPROGS_CFLAGS causes conflicts
+XDP_SAMPLE_CFLAGS += -Wall -O2 \
+		     -I$(src)/../../tools/include \
+		     -I$(src)/../../tools/include/uapi \
+		     -I$(LIBBPF_INCLUDE) \
+		     -I$(src)/../../tools/testing/selftests/bpf
+
+$(obj)/$(XDP_SAMPLE): TPROGS_CFLAGS = $(XDP_SAMPLE_CFLAGS)
+$(obj)/$(XDP_SAMPLE): $(src)/xdp_sample_user.h $(src)/xdp_sample_shared.h
+
 -include $(BPF_SAMPLES_PATH)/Makefile.target
 
 VMLINUX_BTF_PATHS ?= $(abspath $(if $(O),$(O)/vmlinux))				\
@@ -329,16 +365,15 @@
 
 $(obj)/vmlinux.h: $(VMLINUX_BTF) $(BPFTOOL)
 ifeq ($(VMLINUX_H),)
+ifeq ($(VMLINUX_BTF),)
+	$(error Cannot find a vmlinux for VMLINUX_BTF at any of "$(VMLINUX_BTF_PATHS)",\
+		build the kernel or set VMLINUX_BTF or VMLINUX_H variable)
+endif
 	$(Q)$(BPFTOOL) btf dump file $(VMLINUX_BTF) format c > $@
 else
 	$(Q)cp "$(VMLINUX_H)" $@
 endif
 
-ifeq ($(VMLINUX_BTF),)
-	$(error Cannot find a vmlinux for VMLINUX_BTF at any of "$(VMLINUX_BTF_PATHS)",\
-		build the kernel or set VMLINUX_BTF variable)
-endif
-
 clean-files += vmlinux.h
 
 # Get Clang's default includes on this system, as opposed to those seen by
@@ -366,7 +401,7 @@
 	$(Q)$(CLANG) -g -O2 -target bpf -D__TARGET_ARCH_$(SRCARCH) \
 		-Wno-compare-distinct-pointer-types -I$(srctree)/include \
 		-I$(srctree)/samples/bpf -I$(srctree)/tools/include \
-		-I$(srctree)/tools/lib $(CLANG_SYS_INCLUDES) \
+		-I$(LIBBPF_INCLUDE) $(CLANG_SYS_INCLUDES) \
 		-c $(filter %.bpf.c,$^) -o $@
 
 LINKED_SKELS := xdp_redirect_cpu.skel.h xdp_redirect_map_multi.skel.h \
@@ -403,7 +438,7 @@
 	@echo "  CLANG-bpf " $@
 	$(Q)$(CLANG) $(NOSTDINC_FLAGS) $(LINUXINCLUDE) $(BPF_EXTRA_CFLAGS) \
 		-I$(obj) -I$(srctree)/tools/testing/selftests/bpf/ \
-		-I$(srctree)/tools/lib/ \
+		-I$(LIBBPF_INCLUDE) \
 		-D__KERNEL__ -D__BPF_TRACING__ -Wno-unused-value -Wno-pointer-sign \
 		-D__TARGET_ARCH_$(SRCARCH) -Wno-compare-distinct-pointer-types \
 		-Wno-gnu-variable-sized-type-not-at-end \
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/Makefile.target
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/Makefile.target
@@ -73,14 +73,3 @@
       cmd_tprog-cobjs	= $(CC) $(tprogc_flags) -c -o $@ $<
 $(tprog-cobjs): $(obj)/%.o: $(src)/%.c FORCE
 	$(call if_changed_dep,tprog-cobjs)
-
-# Override includes for xdp_sample_user.o because $(srctree)/usr/include in
-# TPROGS_CFLAGS causes conflicts
-XDP_SAMPLE_CFLAGS += -Wall -O2 -lm \
-		     -I./tools/include \
-		     -I./tools/include/uapi \
-		     -I./tools/lib \
-		     -I./tools/testing/selftests/bpf
-$(obj)/xdp_sample_user.o: $(src)/xdp_sample_user.c \
-	$(src)/xdp_sample_user.h $(src)/xdp_sample_shared.h
-	$(CC) $(XDP_SAMPLE_CFLAGS) -c -o $@ $<
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/hbm.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/hbm.c
@@ -308,6 +308,7 @@
 		fout = fopen(fname, "w");
 		fprintf(fout, "id:%d\n", cg_id);
 		fprintf(fout, "ERROR: Could not lookup queue_stats\n");
+		fclose(fout);
 	} else if (stats_flag && qstats.lastPacketTime >
 		   qstats.firstPacketTime) {
 		long long delta_us = (qstats.lastPacketTime -
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/hbm_kern.h
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/hbm_kern.h
@@ -9,8 +9,6 @@
  * Include file for sample Host Bandwidth Manager (HBM) BPF programs
  */
 #define KBUILD_MODNAME "foo"
-#include <stddef.h>
-#include <stdbool.h>
 #include <uapi/linux/bpf.h>
 #include <uapi/linux/if_ether.h>
 #include <uapi/linux/if_packet.h>
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/lwt_len_hist_kern.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/lwt_len_hist_kern.c
@@ -16,13 +16,6 @@
 #include <uapi/linux/in.h>
 #include <bpf/bpf_helpers.h>
 
-# define printk(fmt, ...)						\
-		({							\
-			char ____fmt[] = fmt;				\
-			bpf_trace_printk(____fmt, sizeof(____fmt),	\
-				     ##__VA_ARGS__);			\
-		})
-
 struct bpf_elf_map {
 	__u32 type;
 	__u32 size_key;
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/tcp_basertt_kern.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/tcp_basertt_kern.c
@@ -47,7 +47,7 @@
 		case BPF_SOCK_OPS_BASE_RTT:
 			n = bpf_getsockopt(skops, SOL_TCP, TCP_CONGESTION,
 					   cong, sizeof(cong));
-			if (!n && !__builtin_memcmp(cong, nv, sizeof(nv)+1)) {
+			if (!n && !__builtin_memcmp(cong, nv, sizeof(nv))) {
 				/* Set base_rtt to 80us */
 				rv = 80;
 			} else if (n) {
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/test_cgrp2_sock.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/test_cgrp2_sock.c
@@ -174,8 +174,10 @@
 		return 1;
 	}
 
-	if (get_bind_to_device(sd, name, sizeof(name)) < 0)
+	if (get_bind_to_device(sd, name, sizeof(name)) < 0) {
+		close(sd);
 		return 1;
+	}
 
 	mark = get_somark(sd);
 	prio = get_priority(sd);
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/tracex6_kern.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/tracex6_kern.c
@@ -2,6 +2,8 @@
 #include <linux/version.h>
 #include <uapi/linux/bpf.h>
 #include <bpf/bpf_helpers.h>
+#include <bpf/bpf_tracing.h>
+#include <bpf/bpf_core_read.h>
 
 struct {
 	__uint(type, BPF_MAP_TYPE_PERF_EVENT_ARRAY);
@@ -45,13 +47,24 @@
 	return 0;
 }
 
-SEC("kprobe/htab_map_lookup_elem")
-int bpf_prog2(struct pt_regs *ctx)
+/*
+ * Since *_map_lookup_elem can't be expected to trigger bpf programs
+ * due to potential deadlocks (bpf_disable_instrumentation), this bpf
+ * program will be attached to bpf_map_copy_value (which is called
+ * from map_lookup_elem) and will only filter the hashtable type.
+ */
+SEC("kprobe/bpf_map_copy_value")
+int BPF_KPROBE(bpf_prog2, struct bpf_map *map)
 {
 	u32 key = bpf_get_smp_processor_id();
 	struct bpf_perf_event_value *val, buf;
+	enum bpf_map_type type;
 	int error;
 
+	type = BPF_CORE_READ(map, map_type);
+	if (type != BPF_MAP_TYPE_HASH)
+		return 0;
+
 	error = bpf_perf_event_read_value(&counters, key, &buf, sizeof(buf));
 	if (error)
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/xdp_adjust_tail_kern.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/xdp_adjust_tail_kern.c
@@ -57,6 +57,7 @@
 
 static __always_inline __u16 csum_fold_helper(__u32 csum)
 {
+	csum = (csum & 0xffff) + (csum >> 16);
 	return ~((csum & 0xffff) + (csum >> 16));
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/xdp_redirect_cpu_user.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/xdp_redirect_cpu_user.c
@@ -309,7 +309,6 @@
 	const char *mprog_filename = NULL, *mprog_name = NULL;
 	struct xdp_redirect_cpu *skel;
 	struct bpf_map_info info = {};
-	char ifname_buf[IF_NAMESIZE];
 	struct bpf_cpumap_val value;
 	__u32 infosz = sizeof(info);
 	int ret = EXIT_FAIL_OPTION;
@@ -325,7 +324,6 @@
 	int add_cpu = -1;
 	int ifindex = -1;
 	int *cpu, i, opt;
-	char *ifname;
 	__u32 qsize;
 	int n_cpus;
 
@@ -391,11 +389,10 @@
 		case 'd':
 			if (strlen(optarg) >= IF_NAMESIZE) {
 				fprintf(stderr, "-d/--dev name too long\n");
+				usage(argv, long_options, __doc__, mask, true, skel->obj);
 				goto end_cpu;
 			}
-			ifname = (char *)&ifname_buf;
-			safe_strncpy(ifname, optarg, sizeof(ifname));
-			ifindex = if_nametoindex(ifname);
+			ifindex = if_nametoindex(optarg);
 			if (!ifindex)
 				ifindex = strtoul(optarg, NULL, 0);
 			if (!ifindex) {
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/xdp_sample_user.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/xdp_sample_user.c
@@ -120,7 +120,10 @@
 		__u64 xmit;
 	} totals;
 	struct {
-		__u64 pps;
+		union {
+			__u64 pps;
+			__u64 num;
+		};
 		__u64 drop;
 		__u64 err;
 	} rx_cnt;
@@ -1322,7 +1325,7 @@
 
 static void sample_summary_print(void)
 {
-	double period = sample_out.rx_cnt.pps;
+	double num = sample_out.rx_cnt.num;
 
 	if (sample_out.totals.rx) {
 		double pkts = sample_out.totals.rx;
@@ -1330,7 +1333,7 @@
 		print_always("  Packets received    : %'-10llu\n",
 			     sample_out.totals.rx);
 		print_always("  Average packets/s   : %'-10.0f\n",
-			     sample_round(pkts / period));
+			     sample_round(pkts / num));
 	}
 	if (sample_out.totals.redir) {
 		double pkts = sample_out.totals.redir;
@@ -1338,7 +1341,7 @@
 		print_always("  Packets redirected  : %'-10llu\n",
 			     sample_out.totals.redir);
 		print_always("  Average redir/s     : %'-10.0f\n",
-			     sample_round(pkts / period));
+			     sample_round(pkts / num));
 	}
 	if (sample_out.totals.drop)
 		print_always("  Rx dropped          : %'-10llu\n",
@@ -1355,7 +1358,7 @@
 		print_always("  Packets transmitted : %'-10llu\n",
 			     sample_out.totals.xmit);
 		print_always("  Average transmit/s  : %'-10.0f\n",
-			     sample_round(pkts / period));
+			     sample_round(pkts / num));
 	}
 }
 
@@ -1422,7 +1425,7 @@
 	return 0;
 }
 
-static void sample_summary_update(struct sample_output *out, int interval)
+static void sample_summary_update(struct sample_output *out)
 {
 	sample_out.totals.rx += out->totals.rx;
 	sample_out.totals.redir += out->totals.redir;
@@ -1430,12 +1433,11 @@
 	sample_out.totals.drop_xmit += out->totals.drop_xmit;
 	sample_out.totals.err += out->totals.err;
 	sample_out.totals.xmit += out->totals.xmit;
-	sample_out.rx_cnt.pps += interval;
+	sample_out.rx_cnt.num++;
 }
 
 static void sample_stats_print(int mask, struct stats_record *cur,
-			       struct stats_record *prev, char *prog_name,
-			       int interval)
+			       struct stats_record *prev, char *prog_name)
 {
 	struct sample_output out = {};
 
@@ -1452,7 +1454,7 @@
 	else if (mask & SAMPLE_DEVMAP_XMIT_CNT_MULTI)
 		stats_get_devmap_xmit_multi(cur, prev, 0, &out,
 					    mask & SAMPLE_DEVMAP_XMIT_CNT);
-	sample_summary_update(&out, interval);
+	sample_summary_update(&out);
 
 	stats_print(prog_name, mask, cur, prev, &out);
 }
@@ -1495,7 +1497,7 @@
 }
 
 static int sample_timer_cb(int timerfd, struct stats_record **rec,
-			   struct stats_record **prev, int interval)
+			   struct stats_record **prev)
 {
 	char line[64] = "Summary";
 	int ret;
@@ -1524,7 +1526,7 @@
 		snprintf(line, sizeof(line), "%s->%s", f ?: "?", t ?: "?");
 	}
 
-	sample_stats_print(sample_mask, *rec, *prev, line, interval);
+	sample_stats_print(sample_mask, *rec, *prev, line);
 	return 0;
 }
 
@@ -1579,7 +1581,7 @@
 		if (pfd[0].revents & POLLIN)
 			ret = sample_signal_cb();
 		else if (pfd[1].revents & POLLIN)
-			ret = sample_timer_cb(timerfd, &rec, &prev, interval);
+			ret = sample_timer_cb(timerfd, &rec, &prev);
 
 		if (ret)
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/xdp_sample_user.h
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/xdp_sample_user.h
@@ -45,7 +45,9 @@
 int get_mac_addr(int ifindex, void *mac_addr);
 
 #pragma GCC diagnostic push
+#ifndef __clang__
 #pragma GCC diagnostic ignored "-Wstringop-truncation"
+#endif
 __attribute__((unused))
 static inline char *safe_strncpy(char *dst, const char *src, size_t size)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/samples/bpf/xdpsock_user.c
+++ linux-xilinx-zynqmp-5.15.0/samples/bpf/xdpsock_user.c
@@ -1673,14 +1673,15 @@
 
 	setlocale(LC_ALL, "");
 
+	prev_time = get_nsecs();
+	start_time = prev_time;
+
 	if (!opt_quiet) {
 		ret = pthread_create(&pt, NULL, poller, NULL);
 		if (ret)
 			exit_with_error(ret);
 	}
 
-	prev_time = get_nsecs();
-	start_time = prev_time;
 
 	if (opt_bench == BENCH_RXDROP)
 		rx_drop_all();
--- linux-xilinx-zynqmp-5.15.0.orig/samples/fanotify/Makefile
+++ linux-xilinx-zynqmp-5.15.0/samples/fanotify/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-only
+userprogs-always-y += fs-monitor
+
+userccflags += -I usr/include -Wall
+
--- linux-xilinx-zynqmp-5.15.0.orig/samples/fanotify/fs-monitor.c
+++ linux-xilinx-zynqmp-5.15.0/samples/fanotify/fs-monitor.c
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021, Collabora Ltd.
+ */
+
+#define _GNU_SOURCE
+#include <errno.h>
+#include <err.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <fcntl.h>
+#include <sys/fanotify.h>
+#include <sys/types.h>
+#include <unistd.h>
+#include <sys/types.h>
+
+#ifndef FAN_FS_ERROR
+#define FAN_FS_ERROR		0x00008000
+#define FAN_EVENT_INFO_TYPE_ERROR	5
+
+struct fanotify_event_info_error {
+	struct fanotify_event_info_header hdr;
+	__s32 error;
+	__u32 error_count;
+};
+#endif
+
+#ifndef FILEID_INO32_GEN
+#define FILEID_INO32_GEN	1
+#endif
+
+#ifndef FILEID_INVALID
+#define	FILEID_INVALID		0xff
+#endif
+
+static void print_fh(struct file_handle *fh)
+{
+	int i;
+	uint32_t *h = (uint32_t *) fh->f_handle;
+
+	printf("\tfh: ");
+	for (i = 0; i < fh->handle_bytes; i++)
+		printf("%hhx", fh->f_handle[i]);
+	printf("\n");
+
+	printf("\tdecoded fh: ");
+	if (fh->handle_type == FILEID_INO32_GEN)
+		printf("inode=%u gen=%u\n", h[0], h[1]);
+	else if (fh->handle_type == FILEID_INVALID && !fh->handle_bytes)
+		printf("Type %d (Superblock error)\n", fh->handle_type);
+	else
+		printf("Type %d (Unknown)\n", fh->handle_type);
+
+}
+
+static void handle_notifications(char *buffer, int len)
+{
+	struct fanotify_event_metadata *event =
+		(struct fanotify_event_metadata *) buffer;
+	struct fanotify_event_info_header *info;
+	struct fanotify_event_info_error *err;
+	struct fanotify_event_info_fid *fid;
+	int off;
+
+	for (; FAN_EVENT_OK(event, len); event = FAN_EVENT_NEXT(event, len)) {
+
+		if (event->mask != FAN_FS_ERROR) {
+			printf("unexpected FAN MARK: %llx\n", event->mask);
+			goto next_event;
+		}
+
+		if (event->fd != FAN_NOFD) {
+			printf("Unexpected fd (!= FAN_NOFD)\n");
+			goto next_event;
+		}
+
+		printf("FAN_FS_ERROR (len=%d)\n", event->event_len);
+
+		for (off = sizeof(*event) ; off < event->event_len;
+		     off += info->len) {
+			info = (struct fanotify_event_info_header *)
+				((char *) event + off);
+
+			switch (info->info_type) {
+			case FAN_EVENT_INFO_TYPE_ERROR:
+				err = (struct fanotify_event_info_error *) info;
+
+				printf("\tGeneric Error Record: len=%d\n",
+				       err->hdr.len);
+				printf("\terror: %d\n", err->error);
+				printf("\terror_count: %d\n", err->error_count);
+				break;
+
+			case FAN_EVENT_INFO_TYPE_FID:
+				fid = (struct fanotify_event_info_fid *) info;
+
+				printf("\tfsid: %x%x\n",
+				       fid->fsid.val[0], fid->fsid.val[1]);
+				print_fh((struct file_handle *) &fid->handle);
+				break;
+
+			default:
+				printf("\tUnknown info type=%d len=%d:\n",
+				       info->info_type, info->len);
+			}
+		}
+next_event:
+		printf("---\n\n");
+	}
+}
+
+int main(int argc, char **argv)
+{
+	int fd;
+
+	char buffer[BUFSIZ];
+
+	if (argc < 2) {
+		printf("Missing path argument\n");
+		return 1;
+	}
+
+	fd = fanotify_init(FAN_CLASS_NOTIF|FAN_REPORT_FID, O_RDONLY);
+	if (fd < 0)
+		errx(1, "fanotify_init");
+
+	if (fanotify_mark(fd, FAN_MARK_ADD|FAN_MARK_FILESYSTEM,
+			  FAN_FS_ERROR, AT_FDCWD, argv[1])) {
+		errx(1, "fanotify_mark");
+	}
+
+	while (1) {
+		int n = read(fd, buffer, BUFSIZ);
+
+		if (n < 0)
+			errx(1, "read");
+
+		handle_notifications(buffer, n);
+	}
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/samples/ftrace/ftrace-direct-modify.c
+++ linux-xilinx-zynqmp-5.15.0/samples/ftrace/ftrace-direct-modify.c
@@ -3,6 +3,9 @@
 #include <linux/kthread.h>
 #include <linux/ftrace.h>
 
+extern void my_direct_func1(void);
+extern void my_direct_func2(void);
+
 void my_direct_func1(void)
 {
 	trace_printk("my direct func1\n");
@@ -28,7 +31,7 @@
 "	call my_direct_func1\n"
 "	leave\n"
 "	.size		my_tramp1, .-my_tramp1\n"
-"	ret\n"
+	ASM_RET
 "	.type		my_tramp2, @function\n"
 "	.globl		my_tramp2\n"
 "   my_tramp2:"
@@ -36,7 +39,7 @@
 "	movq %rsp, %rbp\n"
 "	call my_direct_func2\n"
 "	leave\n"
-"	ret\n"
+	ASM_RET
 "	.size		my_tramp2, .-my_tramp2\n"
 "	.popsection\n"
 );
--- linux-xilinx-zynqmp-5.15.0.orig/samples/ftrace/ftrace-direct-too.c
+++ linux-xilinx-zynqmp-5.15.0/samples/ftrace/ftrace-direct-too.c
@@ -4,11 +4,14 @@
 #include <linux/mm.h> /* for handle_mm_fault() */
 #include <linux/ftrace.h>
 
-void my_direct_func(struct vm_area_struct *vma,
-			unsigned long address, unsigned int flags)
+extern void my_direct_func(struct vm_area_struct *vma, unsigned long address,
+			   unsigned int flags, struct pt_regs *regs);
+
+void my_direct_func(struct vm_area_struct *vma, unsigned long address,
+		    unsigned int flags, struct pt_regs *regs)
 {
-	trace_printk("handle mm fault vma=%p address=%lx flags=%x\n",
-		     vma, address, flags);
+	trace_printk("handle mm fault vma=%p address=%lx flags=%x regs=%p\n",
+		     vma, address, flags, regs);
 }
 
 extern void my_tramp(void *);
@@ -23,12 +26,14 @@
 "	pushq %rdi\n"
 "	pushq %rsi\n"
 "	pushq %rdx\n"
+"	pushq %rcx\n"
 "	call my_direct_func\n"
+"	popq %rcx\n"
 "	popq %rdx\n"
 "	popq %rsi\n"
 "	popq %rdi\n"
 "	leave\n"
-"	ret\n"
+	ASM_RET
 "	.size		my_tramp, .-my_tramp\n"
 "	.popsection\n"
 );
--- linux-xilinx-zynqmp-5.15.0.orig/samples/ftrace/ftrace-direct.c
+++ linux-xilinx-zynqmp-5.15.0/samples/ftrace/ftrace-direct.c
@@ -4,6 +4,8 @@
 #include <linux/sched.h> /* for wake_up_process() */
 #include <linux/ftrace.h>
 
+extern void my_direct_func(struct task_struct *p);
+
 void my_direct_func(struct task_struct *p)
 {
 	trace_printk("waking up %s-%d\n", p->comm, p->pid);
@@ -22,7 +24,7 @@
 "	call my_direct_func\n"
 "	popq %rdi\n"
 "	leave\n"
-"	ret\n"
+	ASM_RET
 "	.size		my_tramp, .-my_tramp\n"
 "	.popsection\n"
 );
--- linux-xilinx-zynqmp-5.15.0.orig/samples/hw_breakpoint/data_breakpoint.c
+++ linux-xilinx-zynqmp-5.15.0/samples/hw_breakpoint/data_breakpoint.c
@@ -70,7 +70,9 @@
 static void __exit hw_break_module_exit(void)
 {
 	unregister_wide_hw_breakpoint(sample_hbp);
-	symbol_put(ksym_name);
+#ifdef CONFIG_MODULE_UNLOAD
+	__symbol_put(ksym_name);
+#endif
 	printk(KERN_INFO "HW Breakpoint for %s write uninstalled\n", ksym_name);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/samples/kprobes/kretprobe_example.c
+++ linux-xilinx-zynqmp-5.15.0/samples/kprobes/kretprobe_example.c
@@ -86,7 +86,7 @@
 	ret = register_kretprobe(&my_kretprobe);
 	if (ret < 0) {
 		pr_err("register_kretprobe failed, returned %d\n", ret);
-		return -1;
+		return ret;
 	}
 	pr_info("Planted return probe at %s: %p\n",
 			my_kretprobe.kp.symbol_name, my_kretprobe.kp.addr);
--- linux-xilinx-zynqmp-5.15.0.orig/samples/landlock/sandboxer.c
+++ linux-xilinx-zynqmp-5.15.0/samples/landlock/sandboxer.c
@@ -22,9 +22,9 @@
 #include <unistd.h>
 
 #ifndef landlock_create_ruleset
-static inline int landlock_create_ruleset(
-		const struct landlock_ruleset_attr *const attr,
-		const size_t size, const __u32 flags)
+static inline int
+landlock_create_ruleset(const struct landlock_ruleset_attr *const attr,
+			const size_t size, const __u32 flags)
 {
 	return syscall(__NR_landlock_create_ruleset, attr, size, flags);
 }
@@ -32,17 +32,18 @@
 
 #ifndef landlock_add_rule
 static inline int landlock_add_rule(const int ruleset_fd,
-		const enum landlock_rule_type rule_type,
-		const void *const rule_attr, const __u32 flags)
+				    const enum landlock_rule_type rule_type,
+				    const void *const rule_attr,
+				    const __u32 flags)
 {
-	return syscall(__NR_landlock_add_rule, ruleset_fd, rule_type,
-			rule_attr, flags);
+	return syscall(__NR_landlock_add_rule, ruleset_fd, rule_type, rule_attr,
+		       flags);
 }
 #endif
 
 #ifndef landlock_restrict_self
 static inline int landlock_restrict_self(const int ruleset_fd,
-		const __u32 flags)
+					 const __u32 flags)
 {
 	return syscall(__NR_landlock_restrict_self, ruleset_fd, flags);
 }
@@ -64,20 +65,26 @@
 		}
 	}
 	*path_list = malloc(num_paths * sizeof(**path_list));
+	if (!*path_list)
+		return -1;
+
 	for (i = 0; i < num_paths; i++)
 		(*path_list)[i] = strsep(&env_path, ENV_PATH_TOKEN);
 
 	return num_paths;
 }
 
+/* clang-format off */
+
 #define ACCESS_FILE ( \
 	LANDLOCK_ACCESS_FS_EXECUTE | \
 	LANDLOCK_ACCESS_FS_WRITE_FILE | \
 	LANDLOCK_ACCESS_FS_READ_FILE)
 
-static int populate_ruleset(
-		const char *const env_var, const int ruleset_fd,
-		const __u64 allowed_access)
+/* clang-format on */
+
+static int populate_ruleset(const char *const env_var, const int ruleset_fd,
+			    const __u64 allowed_access)
 {
 	int num_paths, i, ret = 1;
 	char *env_path_name;
@@ -95,6 +102,10 @@
 	env_path_name = strdup(env_path_name);
 	unsetenv(env_var);
 	num_paths = parse_path(env_path_name, &path_list);
+	if (num_paths < 0) {
+		fprintf(stderr, "Failed to allocate memory\n");
+		goto out_free_name;
+	}
 	if (num_paths == 1 && path_list[0][0] == '\0') {
 		/*
 		 * Allows to not use all possible restrictions (e.g. use
@@ -107,12 +118,10 @@
 	for (i = 0; i < num_paths; i++) {
 		struct stat statbuf;
 
-		path_beneath.parent_fd = open(path_list[i], O_PATH |
-				O_CLOEXEC);
+		path_beneath.parent_fd = open(path_list[i], O_PATH | O_CLOEXEC);
 		if (path_beneath.parent_fd < 0) {
 			fprintf(stderr, "Failed to open \"%s\": %s\n",
-					path_list[i],
-					strerror(errno));
+				path_list[i], strerror(errno));
 			goto out_free_name;
 		}
 		if (fstat(path_beneath.parent_fd, &statbuf)) {
@@ -123,9 +132,10 @@
 		if (!S_ISDIR(statbuf.st_mode))
 			path_beneath.allowed_access &= ACCESS_FILE;
 		if (landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-					&path_beneath, 0)) {
-			fprintf(stderr, "Failed to update the ruleset with \"%s\": %s\n",
-					path_list[i], strerror(errno));
+				      &path_beneath, 0)) {
+			fprintf(stderr,
+				"Failed to update the ruleset with \"%s\": %s\n",
+				path_list[i], strerror(errno));
 			close(path_beneath.parent_fd);
 			goto out_free_name;
 		}
@@ -134,10 +144,13 @@
 	ret = 0;
 
 out_free_name:
+	free(path_list);
 	free(env_path_name);
 	return ret;
 }
 
+/* clang-format off */
+
 #define ACCESS_FS_ROUGHLY_READ ( \
 	LANDLOCK_ACCESS_FS_EXECUTE | \
 	LANDLOCK_ACCESS_FS_READ_FILE | \
@@ -155,6 +168,8 @@
 	LANDLOCK_ACCESS_FS_MAKE_BLOCK | \
 	LANDLOCK_ACCESS_FS_MAKE_SYM)
 
+/* clang-format on */
+
 int main(const int argc, char *const argv[], char *const *const envp)
 {
 	const char *cmd_path;
@@ -162,55 +177,64 @@
 	int ruleset_fd;
 	struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = ACCESS_FS_ROUGHLY_READ |
-			ACCESS_FS_ROUGHLY_WRITE,
+				     ACCESS_FS_ROUGHLY_WRITE,
 	};
 
 	if (argc < 2) {
-		fprintf(stderr, "usage: %s=\"...\" %s=\"...\" %s <cmd> [args]...\n\n",
-				ENV_FS_RO_NAME, ENV_FS_RW_NAME, argv[0]);
-		fprintf(stderr, "Launch a command in a restricted environment.\n\n");
+		fprintf(stderr,
+			"usage: %s=\"...\" %s=\"...\" %s <cmd> [args]...\n\n",
+			ENV_FS_RO_NAME, ENV_FS_RW_NAME, argv[0]);
+		fprintf(stderr,
+			"Launch a command in a restricted environment.\n\n");
 		fprintf(stderr, "Environment variables containing paths, "
 				"each separated by a colon:\n");
-		fprintf(stderr, "* %s: list of paths allowed to be used in a read-only way.\n",
-				ENV_FS_RO_NAME);
-		fprintf(stderr, "* %s: list of paths allowed to be used in a read-write way.\n",
-				ENV_FS_RW_NAME);
-		fprintf(stderr, "\nexample:\n"
-				"%s=\"/bin:/lib:/usr:/proc:/etc:/dev/urandom\" "
-				"%s=\"/dev/null:/dev/full:/dev/zero:/dev/pts:/tmp\" "
-				"%s bash -i\n",
-				ENV_FS_RO_NAME, ENV_FS_RW_NAME, argv[0]);
+		fprintf(stderr,
+			"* %s: list of paths allowed to be used in a read-only way.\n",
+			ENV_FS_RO_NAME);
+		fprintf(stderr,
+			"* %s: list of paths allowed to be used in a read-write way.\n",
+			ENV_FS_RW_NAME);
+		fprintf(stderr,
+			"\nexample:\n"
+			"%s=\"/bin:/lib:/usr:/proc:/etc:/dev/urandom\" "
+			"%s=\"/dev/null:/dev/full:/dev/zero:/dev/pts:/tmp\" "
+			"%s bash -i\n",
+			ENV_FS_RO_NAME, ENV_FS_RW_NAME, argv[0]);
 		return 1;
 	}
 
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	if (ruleset_fd < 0) {
 		const int err = errno;
 
 		perror("Failed to create a ruleset");
 		switch (err) {
 		case ENOSYS:
-			fprintf(stderr, "Hint: Landlock is not supported by the current kernel. "
-					"To support it, build the kernel with "
-					"CONFIG_SECURITY_LANDLOCK=y and prepend "
-					"\"landlock,\" to the content of CONFIG_LSM.\n");
+			fprintf(stderr,
+				"Hint: Landlock is not supported by the current kernel. "
+				"To support it, build the kernel with "
+				"CONFIG_SECURITY_LANDLOCK=y and prepend "
+				"\"landlock,\" to the content of CONFIG_LSM.\n");
 			break;
 		case EOPNOTSUPP:
-			fprintf(stderr, "Hint: Landlock is currently disabled. "
-					"It can be enabled in the kernel configuration by "
-					"prepending \"landlock,\" to the content of CONFIG_LSM, "
-					"or at boot time by setting the same content to the "
-					"\"lsm\" kernel parameter.\n");
+			fprintf(stderr,
+				"Hint: Landlock is currently disabled. "
+				"It can be enabled in the kernel configuration by "
+				"prepending \"landlock,\" to the content of CONFIG_LSM, "
+				"or at boot time by setting the same content to the "
+				"\"lsm\" kernel parameter.\n");
 			break;
 		}
 		return 1;
 	}
 	if (populate_ruleset(ENV_FS_RO_NAME, ruleset_fd,
-				ACCESS_FS_ROUGHLY_READ)) {
+			     ACCESS_FS_ROUGHLY_READ)) {
 		goto err_close_ruleset;
 	}
 	if (populate_ruleset(ENV_FS_RW_NAME, ruleset_fd,
-				ACCESS_FS_ROUGHLY_READ | ACCESS_FS_ROUGHLY_WRITE)) {
+			     ACCESS_FS_ROUGHLY_READ |
+				     ACCESS_FS_ROUGHLY_WRITE)) {
 		goto err_close_ruleset;
 	}
 	if (prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0)) {
@@ -227,7 +251,7 @@
 	cmd_argv = argv + 1;
 	execvpe(cmd_path, cmd_argv, envp);
 	fprintf(stderr, "Failed to execute \"%s\": %s\n", cmd_path,
-			strerror(errno));
+		strerror(errno));
 	fprintf(stderr, "Hint: access to the binary, the interpreter or "
 			"shared libraries may be denied.\n");
 	return 1;
--- linux-xilinx-zynqmp-5.15.0.orig/samples/pktgen/pktgen_sample01_simple.sh
+++ linux-xilinx-zynqmp-5.15.0/samples/pktgen/pktgen_sample01_simple.sh
@@ -72,7 +72,7 @@
     pg_set $DEV "udp_dst_max $UDP_DST_MAX"
 fi
 
-[ ! -z "$UDP_CSUM" ] && pg_set $dev "flag UDPCSUM"
+[ ! -z "$UDP_CSUM" ] && pg_set $DEV "flag UDPCSUM"
 
 # Setup random UDP port src range
 pg_set $DEV "flag UDPSRC_RND"
--- linux-xilinx-zynqmp-5.15.0.orig/samples/vfio-mdev/mdpy-fb.c
+++ linux-xilinx-zynqmp-5.15.0/samples/vfio-mdev/mdpy-fb.c
@@ -109,7 +109,7 @@
 
 	ret = pci_request_regions(pdev, "mdpy-fb");
 	if (ret < 0)
-		return ret;
+		goto err_disable_dev;
 
 	pci_read_config_dword(pdev, MDPY_FORMAT_OFFSET, &format);
 	pci_read_config_dword(pdev, MDPY_WIDTH_OFFSET,	&width);
@@ -191,6 +191,9 @@
 err_release_regions:
 	pci_release_regions(pdev);
 
+err_disable_dev:
+	pci_disable_device(pdev);
+
 	return ret;
 }
 
@@ -199,7 +202,10 @@
 	struct fb_info *info = pci_get_drvdata(pdev);
 
 	unregister_framebuffer(info);
+	iounmap(info->screen_base);
 	framebuffer_release(info);
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
 }
 
 static struct pci_device_id mdpy_fb_pci_table[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/samples/xilinx_apm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/samples/xilinx_apm/Makefile
@@ -0,0 +1,71 @@
+#
+# 'make depend' uses makedepend to automatically generate dependencies
+#               (dependencies are added to end of Makefile)
+# 'make'        build executable file 'mycc'
+# 'make clean'  removes all .o and executable files
+#
+
+# define the C compiler to use
+CC = $(CROSS_COMPILE)gcc
+
+# define any compile-time flags
+CFLAGS = -Wall -g
+
+# define any directories containing header files other than /usr/include
+#
+INCLUDES =
+
+# define library paths in addition to /usr/lib
+#   if I wanted to include libraries not in /usr/lib I'd specify
+#   their path using -Lpath, something like:
+LFLAGS =
+
+# define any libraries to link into executable:
+#   if I want to link in libraries (libx.so or libx.a) I use the -llibname
+#   option, something like (this will link in libmylib.so and libm.so:
+LIBS =  -lm
+
+# define the C source files
+SRCS = main.c xaxipmon.c
+
+# define the C object files
+#
+# This uses Suffix Replacement within a macro:
+#   $(name:string1=string2)
+#         For each word in 'name' replace 'string1' with 'string2'
+# Below we are replacing the suffix .c of all words in the macro SRCS
+# with the .o suffix
+#
+OBJS = $(SRCS:.c=.o)
+
+# define the executable file
+MAIN = main
+
+#
+# The following part of the makefile is generic; it can be used to
+# build any executable just by changing the definitions above and by
+# deleting dependencies appended to the file from 'make depend'
+#
+
+.PHONY: depend clean
+
+all:    $(MAIN)
+	@echo  Xilinx AXI Performance Monitor application compiled
+
+$(MAIN): $(OBJS)
+	$(CC) $(CFLAGS) $(INCLUDES) -o $(MAIN) $(OBJS) $(LFLAGS) $(LIBS)
+
+# this is a suffix replacement rule for building .o's from .c's
+# it uses automatic variables $<: the name of the prerequisite of
+# the rule(a .c file) and $@: the name of the target of the rule (a .o file)
+# (see the gnu make manual section about automatic variables)
+.c.o:
+	$(CC) $(CFLAGS) $(INCLUDES) -c $<  -o $@
+
+clean:
+	$(RM) *.o *~ $(MAIN)
+
+depend: $(SRCS)
+	makedepend $(INCLUDES) $^
+
+# DO NOT DELETE THIS LINE -- make depend needs it
--- linux-xilinx-zynqmp-5.15.0.orig/samples/xilinx_apm/main.c
+++ linux-xilinx-zynqmp-5.15.0/samples/xilinx_apm/main.c
@@ -0,0 +1,134 @@
+/*
+ * Xilinx AXI Performance Monitor Example
+ *
+ * Copyright (c) 2013 Xilinx Inc.
+ *
+ * The code may be used by anyone for any purpose and can serve as a
+ * starting point for developing applications using Xilinx AXI
+ * Performance Monitor.
+ *
+ * This example based on Xilinx AXI Performance Monitor UIO driver shows
+ * sequence to read metrics from Xilinx AXI Performance Monitor IP.
+ * User need to provide the uio device file with option -d:
+ * main -d /dev/uio0, say /dev/uio0 as device file for AXI Performance
+ * Monitor driver. User need not clear Interrupt Status Register after
+ * waiting for interrupt on read since driver clears it.
+ */
+#include <stdio.h>
+#include <stdlib.h>
+#include <unistd.h>
+#include <string.h>
+#include <sys/mman.h>
+#include <fcntl.h>
+#include <sys/stat.h>
+#include <errno.h>
+#include <sys/msg.h>
+#include <sys/ipc.h>
+#include <stdint.h>
+#include "xaxipmon.h"
+
+#define MAP_SIZE 4096
+
+void usage(void)
+{
+	printf("*argv[0] -d <UIO_DEV_FILE> -i|-o <VALUE>\n");
+	printf(" -d UIO device file. e.g. /dev/uio0\n");
+	return;
+}
+
+static void start(int fd)
+{
+	u8 slot = 2;
+	int tmp;
+	u32 isr;
+
+	setmetrics(slot, XAPM_METRIC_SET_4, XAPM_METRIC_COUNTER_0);
+	setsampleinterval(0x3FFFFFF);
+
+	loadsic();
+
+	intrenable(XAPM_IXR_SIC_OVERFLOW_MASK);
+
+	intrglobalenable();
+
+	enablemetricscounter();
+
+	enablesic();
+
+	isr = intrgetstatus();
+	/* Wait for SIC overflow interrupt */
+	if (read(fd, &tmp, 4) < 0)
+		perror("Read\n");
+	/* Driver clears the interrupt and occured interrupt status is
+		stored in param->isr */
+	isr = intrgetstatus();
+	if (isr & XAPM_IXR_SIC_OVERFLOW_MASK)
+		disablesic();
+
+	disablemetricscounter();
+
+	intrdisable(XAPM_IXR_SIC_OVERFLOW_MASK);
+
+	intrglobaldisable();
+
+	printf("Required metrics: %u\n",
+		getsampledmetriccounter(XAPM_METRIC_COUNTER_0) *
+		params->scalefactor);
+}
+
+int main(int argc, char *argv[])
+{
+	int c;
+	char *uiod;
+	int fd;
+
+	while ((c = getopt(argc, argv, "d:h")) != -1) {
+		switch (c) {
+		case 'd':
+			uiod = optarg;
+			break;
+		case 'h':
+			usage();
+			return 0;
+		default:
+			printf("invalid option: %c\n", (char)c);
+			usage();
+			return -1;
+		}
+	}
+
+	/* Open the UIO device file */
+	fd = open(uiod, O_RDWR);
+	if (fd < 1) {
+		perror(argv[0]);
+		printf("Invalid UIO device file:%s.\n", uiod);
+		usage();
+		return -1;
+	}
+
+	baseaddr = (ulong)mmap(0, MAP_SIZE , PROT_READ|PROT_WRITE,
+				MAP_SHARED , fd, 0);
+	if ((u32 *)baseaddr == MAP_FAILED)
+		perror("mmap failed\n");
+
+	/* mmap the UIO device */
+	params = (struct xapm_param *)mmap(0, MAP_SIZE , PROT_READ|PROT_WRITE,
+				MAP_SHARED , fd, getpagesize());
+	if (params == MAP_FAILED)
+		perror("mmap failed\n");
+
+	if (params->mode == 1)
+		printf("AXI PMON is in Advanced Mode\n");
+	else if (params->mode == 2)
+		printf("AXI PMON is in Profile Mode\n");
+	else
+		printf("AXI PMON is in trace Mode\n");
+
+	start(fd);
+
+	close(fd);
+	munmap((u32 *)baseaddr, MAP_SIZE);
+	munmap(params, MAP_SIZE);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/samples/xilinx_apm/xaxipmon.c
+++ linux-xilinx-zynqmp-5.15.0/samples/xilinx_apm/xaxipmon.c
@@ -0,0 +1,1269 @@
+#include "xaxipmon.h"
+/*****************************************************************************/
+/**
+*
+* This function resets all Metric Counters and Sampled Metric Counters of
+* AXI Performance Monitor.
+*
+* @return	XST_SUCCESS
+*
+*
+* @note		None.
+*
+******************************************************************************/
+int resetmetriccounter(void)
+{
+	u32 regval;
+
+	/*
+	 * Write the reset value to the Control register to reset
+	 * Metric counters
+	 */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+					(regval | XAPM_CR_MCNTR_RESET_MASK));
+	/*
+	 * Release from Reset
+	 */
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				(regval & ~(XAPM_CR_MCNTR_RESET_MASK)));
+	return XST_SUCCESS;
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function resets Global Clock Counter of AXI Performance Monitor
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void resetglobalclkcounter(void)
+{
+
+	u32 regval;
+
+	/*
+	 * Write the reset value to the Control register to reset
+	 * Global Clock Counter
+	 */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+					(regval | XAPM_CR_GCC_RESET_MASK));
+
+	/*
+	 * Release from Reset
+	 */
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				(regval & ~(XAPM_CR_GCC_RESET_MASK)));
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function resets Streaming FIFO of AXI Performance Monitor
+*
+* @return	XST_SUCCESS
+*
+* @note		None.
+*
+******************************************************************************/
+int resetfifo(void)
+{
+	u32 regval;
+
+	/* Check Event Logging is enabled in Hardware */
+	if (params->eventlog == 0)
+		/*Event Logging not enabled in Hardware*/
+		return XST_SUCCESS;
+
+	/*
+	 * Write the reset value to the Control register to reset
+	 * FIFO
+	 */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+					(regval | XAPM_CR_FIFO_RESET_MASK));
+	/*
+	 * Release from Reset
+	 */
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				(regval & ~(XAPM_CR_FIFO_RESET_MASK)));
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets Ranges for Incrementers depending on parameters passed.
+*
+* @param	incrementer specifies the Incrementer for which Ranges
+*		need to be set
+* @param	rangehigh specifies the Upper limit in 32 bit Register
+* @param	rangelow specifies the Lower limit in 32 bit Register
+*
+* @return	None.
+*
+* @note		None
+*
+*****************************************************************************/
+void setincrementerrange(u8 incrementer, u16 rangehigh, u16 rangelow)
+{
+	u32 regval;
+
+	/*
+	 * Write to the specified Range register
+	 */
+	regval = rangehigh << 16;
+	regval |= rangelow;
+	writereg(baseaddr,
+		(XAPM_RANGE0_OFFSET + (incrementer * 16)), regval);
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the Ranges of Incrementers Registers.
+*
+* @param	incrementer specifies the Incrementer for which Ranges
+*		need to be returned.
+* @param	rangehigh specifies the user reference variable which returns
+*		the Upper Range Value of the specified Incrementer.
+* @param	rangelow specifies the user reference variable which returns
+*		the Lower Range Value of the specified Incrementer.
+*
+* @return	None.
+*
+* @note		None
+*
+*****************************************************************************/
+void getincrementerrange(u8 incrementer, u16 *rangehigh, u16 *rangelow)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, (XAPM_RANGE0_OFFSET +
+					(incrementer * 16)));
+
+	*rangelow = regval & 0xFFFF;
+	*rangehigh = (regval >> 16) & 0xFFFF;
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets the Sample Interval Register
+*
+* @param	sampleinterval is the Sample Interval
+*
+* @return	None
+*
+* @note		None.
+*
+*****************************************************************************/
+void setsampleinterval(u32 sampleinterval)
+{
+	/*
+	 * Set Sample Interval
+	 */
+	writereg(baseaddr, XAPM_SI_LOW_OFFSET, sampleinterval);
+
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the contents of Sample Interval Register
+*
+* @param	sampleinterval is a pointer where Sample Interval register
+*		contents are returned.
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void getsampleinterval(u32 *sampleinterval)
+{
+	/*
+	 * Set Sample Interval Lower
+	 */
+	*sampleinterval = readreg(baseaddr, XAPM_SI_LOW_OFFSET);
+
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets metrics for specified Counter in the corresponding
+* Metric Selector Register.
+*
+* @param	slot is the slot ID for which specified counter has to
+*		be connected.
+* @param	metrics is one of the Metric Sets. User has to use
+*		XAPM_METRIC_SET_* macros in xaxipmon.h for this parameter
+* @param	counter is the Counter Number.
+*		The valid values are 0 to 9.
+*
+* @return	XST_SUCCESS if Success
+*		XST_FAILURE if Failure
+*
+* @note		None.
+*
+*****************************************************************************/
+int setmetrics(u8 slot, u8 metrics, u8 counter)
+{
+	u32 regval;
+	u32 mask;
+
+	/* Find mask value to force zero in counternum byte range */
+	if (counter == 0 || counter == 4 || counter == 8)
+		mask = 0xFFFFFF00;
+	else if (counter == 1 || counter == 5 || counter == 9)
+		mask = 0xFFFF00FF;
+	else if (counter == 2 || counter == 6)
+		mask = 0xFF00FFFF;
+	else
+		mask = 0x00FFFFFF;
+
+	if (counter <= 3) {
+		regval = readreg(baseaddr, XAPM_MSR0_OFFSET);
+		regval = regval & mask;
+		regval = regval | (metrics << (counter * 8));
+		regval = regval | (slot << (counter * 8 + 5));
+		writereg(baseaddr, XAPM_MSR0_OFFSET, regval);
+	} else if ((counter >= 4) && (counter <= 7)) {
+		counter = counter - 4;
+		regval = readreg(baseaddr, XAPM_MSR1_OFFSET);
+		regval = regval & mask;
+		regval = regval | (metrics << (counter * 8));
+		regval = regval | (slot << (counter * 8 + 5));
+		writereg(baseaddr, XAPM_MSR1_OFFSET, regval);
+	} else {
+		counter = counter - 8;
+		regval = readreg(baseaddr, XAPM_MSR2_OFFSET);
+
+		regval = regval & mask;
+		regval = regval | (metrics << (counter * 8));
+		regval = regval | (slot << (counter * 8 + 5));
+		writereg(baseaddr, XAPM_MSR2_OFFSET, regval);
+	}
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns metrics in the specified Counter from the corresponding
+* Metric Selector Register.
+*
+* @param	counter is the Counter Number.
+*		The valid values are 0 to 9.
+* @param	metrics is a reference parameter from application where metrics
+*		of specified counter is filled.
+* @praram	slot is a reference parameter in which slot Id of
+*		specified counter is filled
+* @return	XST_SUCCESS if Success
+*		XST_FAILURE if Failure
+*
+* @note		None.
+*
+*****************************************************************************/
+int getmetrics(u8 counter, u8 *metrics, u8 *slot)
+{
+	u32 regval;
+
+	if (counter <= 3) {
+		regval = readreg(baseaddr, XAPM_MSR0_OFFSET);
+		*metrics = (regval >> (counter * 8)) & 0x1F;
+		*slot	= (regval >> (counter * 8 + 5)) & 0x7;
+	} else if ((counter >= 4) && (counter <= 7)) {
+		counter = counter - 4;
+		regval = readreg(baseaddr, XAPM_MSR1_OFFSET);
+		*metrics = (regval >> (counter * 8)) & 0x1F;
+		*slot	= (regval >> (counter * 8 + 5)) & 0x7;
+	} else {
+		counter = counter - 8;
+		regval = readreg(baseaddr, XAPM_MSR2_OFFSET);
+		*metrics = (regval >> (counter * 8)) & 0x1F;
+		*slot	= (regval >> (counter * 8 + 5)) & 0x7;
+	}
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the contents of the Global Clock Counter Register.
+*
+* @param	cnthigh is the user space pointer with which upper 32 bits
+*		of Global Clock Counter has to be filled
+* @param	cntlow is the user space pointer with which lower 32 bits
+*		of Global Clock Counter has to be filled
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void getglobalclkcounter(u32 *cnthigh, u32 *cntlow)
+{
+	*cnthigh = 0x0;
+	*cntlow  = 0x0;
+
+	/*
+	 * If Counter width is 64 bit then Counter Value has to be
+	 * filled at CntHighValue address also.
+	 */
+	if (params->globalcntwidth == 64) {
+		/* Bits[63:32] exists at XAPM_GCC_HIGH_OFFSET */
+		*cnthigh = readreg(baseaddr, XAPM_GCC_HIGH_OFFSET);
+	}
+	/* Bits[31:0] exists at XAPM_GCC_LOW_OFFSET */
+	*cntlow = readreg(baseaddr, XAPM_GCC_LOW_OFFSET);
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the contents of the Metric Counter Register.
+*
+* @param	counter is the number of the Metric Counter to be read.
+*		Use the XAPM_METRIC_COUNTER* defines for the counter number in
+*		xaxipmon.h. The valid values are 0 (XAPM_METRIC_COUNTER_0) to
+*		9 (XAPM_METRIC_COUNTER_9).
+* @return	regval is the content of specified Metric Counter.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getmetriccounter(u32 counter)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr,
+				(XAPM_MC0_OFFSET + (counter * 16)));
+	return regval;
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the contents of the Sampled Metric Counter Register.
+*
+* @param	counter is the number of the Sampled Metric Counter to read.
+*		Use the XAPM_METRIC_COUNTER* defines for the counter number in
+*		xaxipmon.h. The valid values are 0 (XAPM_METRIC_COUNTER_0) to
+*		9 (XAPM_METRIC_COUNTER_9).
+*
+* @return	regval is the content of specified Sampled Metric Counter.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getsampledmetriccounter(u32 counter)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, (XAPM_SMC0_OFFSET +
+						(counter * 16)));
+	return regval;
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the contents of the Incrementer Register.
+*
+* @param	incrementer is the number of the Incrementer register to
+*		read.Use the XAPM_INCREMENTER_* defines for the Incrementer
+*		number.The valid values are 0 (XAPM_INCREMENTER_0) to
+*		9 (XAPM_INCREMENTER_9).
+* @param	incrementer is the number of the specified Incrementer
+*		register
+* @return	regval is content of specified Metric Incrementer register.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getincrementer(u32 incrementer)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, (XAPM_INC0_OFFSET +
+						(incrementer * 16)));
+	return regval;
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the contents of the Sampled Incrementer Register.
+*
+* @param	incrementer is the number of the Sampled Incrementer
+*		register to read.Use the XAPM_INCREMENTER_* defines for the
+*		Incrementer number.The valid values are 0 (XAPM_INCREMENTER_0)
+*		to 9 (XAPM_INCREMENTER_9).
+* @param	incrementer is the number of the specified Sampled
+*		Incrementer register
+* @return	regval is content of specified Sampled Incrementer register.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getsampledincrementer(u32 incrementer)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, (XAPM_SINC0_OFFSET +
+					(incrementer * 16)));
+	return regval;
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets Software-written Data Register.
+*
+* @param	swdata is the Software written Data.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void setswdatareg(u32 swdata)
+{
+	/*
+	 * Set Software-written Data Register
+	 */
+	writereg(baseaddr, XAPM_SWD_OFFSET, swdata);
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns contents of Software-written Data Register.
+*
+* @return	swdata.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getswdatareg(void)
+{
+	u32 swdata;
+
+	/*
+	 * Set Metric Selector Register
+	 */
+	swdata = (u32)readreg(baseaddr, XAPM_SWD_OFFSET);
+	return swdata;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the following in the AXI Performance Monitor:
+*   - Event logging
+*
+* @param        flagenables is a value to write to the flag enables
+*               register defined by XAPM_FEC_OFFSET. It is recommended
+*               to use the XAPM_FEC_*_MASK mask bits to generate.
+*               A value of 0x0 will disable all events to the event
+*               log streaming FIFO.
+*
+* @return       XST_SUCCESS
+*
+* @note         None
+*
+******************************************************************************/
+int starteventlog(u32 flagenables)
+{
+	u32 regval;
+
+	/* Read current register value */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	/* Now write to flag enables register */
+	writereg(baseaddr, XAPM_FEC_OFFSET, flagenables);
+	/* Write the new value to the Control register to
+	 *	enable event logging */
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+			regval | XAPM_CR_EVENTLOG_ENABLE_MASK);
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the following in the AXI Performance Monitor:
+*   - Event logging
+*
+* @return       XST_SUCCESS
+*
+* @note         None
+*
+******************************************************************************/
+int stopeventlog(void)
+{
+	u32 regval;
+
+	/* Read current register value */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+
+	/* Write the new value to the Control register to disable
+	 * event logging */
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				regval & ~XAPM_CR_EVENTLOG_ENABLE_MASK);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the following in the AXI Performance Monitor:
+*   - Global clock counter
+*   - All metric counters
+*   - All sampled metric counters
+*
+* @param    sampleinterval is the sample interval
+* @return   XST_SUCCESS
+*
+* @note	    None
+******************************************************************************/
+int startcounters(u32 sampleinterval)
+{
+	u32 regval;
+
+	/* Read current register value */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+
+	/* Global Clock Counter is present in Advanced Mode only */
+	if (params->mode == 1)
+		regval = regval | XAPM_CR_GCC_ENABLE_MASK;
+	/*
+	 * Write the new value to the Control register to enable
+	 * global clock counter and metric counters
+	 */
+	writereg(baseaddr, XAPM_CTL_OFFSET, regval | XAPM_CR_MCNTR_ENABLE_MASK);
+
+	/* Set, enable, and load sampled counters */
+	setsampleinterval(sampleinterval);
+	loadsic();
+	enablesic();
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+*
+* This function disables the following in the AXI Performance Monitor:
+*   - Global clock counter
+*   - All metric counters
+*
+* @return       XST_SUCCESS
+*
+* @note         None
+*
+******************************************************************************/
+int stopcounters(void)
+{
+	u32 regval;
+
+	/* Read current register value */
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+
+	/* Global Clock Counter is present in Advanced Mode only */
+	if (params->mode == 1)
+		regval = regval & ~XAPM_CR_GCC_ENABLE_MASK;
+
+	/*
+	 * Write the new value to the Control register to disable
+	 * global clock counter and metric counters
+	 */
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+			regval & ~XAPM_CR_MCNTR_ENABLE_MASK);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables Metric Counters.
+*
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void enablemetricscounter(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+					regval | XAPM_CR_MCNTR_ENABLE_MASK);
+}
+/****************************************************************************/
+/**
+*
+* This function disables the Metric Counters.
+*
+* @return	None
+*
+* @note		None
+*
+*****************************************************************************/
+void disablemetricscounter(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+					regval & ~(XAPM_CR_MCNTR_ENABLE_MASK));
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets the Upper and Lower Ranges for specified Metric Counter
+* Log Enable Register.Event Logging starts when corresponding Metric Counter
+* value falls in between these ranges
+*
+* @param	counter is the Metric Counter number for which
+*		Ranges are to be assigned.Use the XAPM_METRIC_COUNTER*
+*		defines for the counter number in xaxipmon.h.
+*		The valid values are 0 (XAPM_METRIC_COUNTER_0) to
+*		9 (XAPM_METRIC_COUNTER_9).
+* @param	rangehigh specifies the Upper limit in 32 bit Register
+* @param	rangelow specifies the Lower limit in 32 bit Register
+* @return	None
+*
+* @note		None.
+*
+*****************************************************************************/
+void setlogenableranges(u32 counter, u16 rangehigh, u16 rangelow)
+{
+	u32 regval;
+
+	/*
+	 * Write the specified Ranges to corresponding Metric Counter Log
+	 * Enable Register
+	 */
+	regval = rangehigh << 16;
+	regval |= rangelow;
+	writereg(baseaddr, (XAPM_MC0LOGEN_OFFSET +
+					(counter * 16)), regval);
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns the Ranges of specified Metric Counter Log
+* Enable Register.
+*
+* @param	counter is the Metric Counter number for which
+*		Ranges are to be returned.Use the XAPM_METRIC_COUNTER*
+*		defines for the counter number in xaxipmon.h.
+*		The valid values are 0 (XAPM_METRIC_COUNTER_0) to
+*		9 (XAPM_METRIC_COUNTER_9).
+*
+* @param	rangehigh specifies the user reference variable which returns
+*		the Upper Range Value of the specified Metric Counter
+*		Log Enable Register.
+* @param	rangelow specifies the user reference variable which returns
+*		the Lower Range Value of the specified Metric Counter
+*		Log Enable Register.
+*
+* @note		None.
+*
+*****************************************************************************/
+void getlogenableranges(u32 counter, u16 *rangehigh, u16 *rangelow)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr,
+				(XAPM_MC0LOGEN_OFFSET + (counter * 16)));
+
+	*rangelow = regval & 0xFFFF;
+	*rangehigh = (regval >> 16) & 0xFFFF;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables Event Logging.
+*
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void enableeventlog(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				regval | XAPM_CR_EVENTLOG_ENABLE_MASK);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables External trigger pulse so that Metric Counters can be
+* started on external trigger pulse for a slot.
+*
+*
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void enablemctrigger(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+			regval | XAPM_CR_MCNTR_EXTTRIGGER_MASK);
+}
+
+/****************************************************************************/
+/**
+*
+* This function disables the External trigger pulse used to start Metric
+* Counters on external trigger pulse for a slot.
+*
+* @return	None
+*
+* @note		None
+*
+*****************************************************************************/
+void disablemctrigger(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+			regval & ~(XAPM_CR_MCNTR_EXTTRIGGER_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables External trigger pulse for Event Log
+* so that Event Logging can be started on external trigger pulse for a slot.
+*
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void enableeventlogtrigger(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				regval | XAPM_CR_EVTLOG_EXTTRIGGER_MASK);
+}
+
+/****************************************************************************/
+/**
+*
+* This function disables the External trigger pulse used to start Event
+* Log on external trigger pulse for a slot.
+*
+* @return	None
+*
+* @note		None
+*
+*****************************************************************************/
+void disableeventlogtrigger(void)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+
+	writereg(baseaddr, XAPM_CTL_OFFSET,
+				regval & ~(XAPM_CR_EVTLOG_EXTTRIGGER_MASK));
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns a name for a given Metric.
+*
+* @param        metrics is one of the Metric Sets. User has to use
+*               XAPM_METRIC_SET_* macros in xaxipmon.h for this parameter
+*
+* @return       const char *
+*
+* @note         None
+*
+*****************************************************************************/
+const char *getmetricname(u8 metrics)
+{
+	if (metrics == XAPM_METRIC_SET_0)
+		return "Write Transaction Count";
+	if (metrics == XAPM_METRIC_SET_1)
+		return "Read Transaction Count";
+	if (metrics == XAPM_METRIC_SET_2)
+		return "Write Byte Count";
+	if (metrics == XAPM_METRIC_SET_3)
+		return "Read Byte Count";
+	if (metrics == XAPM_METRIC_SET_4)
+		return "Write Beat Count";
+	if (metrics == XAPM_METRIC_SET_5)
+		return "Total Read Latency";
+	if (metrics == XAPM_METRIC_SET_6)
+		return "Total Write Latency";
+	if (metrics == XAPM_METRIC_SET_7)
+		return "Slv_Wr_Idle_Cnt";
+	if (metrics == XAPM_METRIC_SET_8)
+		return "Mst_Rd_Idle_Cnt";
+	if (metrics == XAPM_METRIC_SET_9)
+		return "Num_BValids";
+	if (metrics == XAPM_METRIC_SET_10)
+		return "Num_WLasts";
+	if (metrics == XAPM_METRIC_SET_11)
+		return "Num_RLasts";
+	if (metrics == XAPM_METRIC_SET_12)
+		return "Minimum Write Latency";
+	if (metrics == XAPM_METRIC_SET_13)
+		return "Maximum Write Latency";
+	if (metrics == XAPM_METRIC_SET_14)
+		return "Minimum Read Latency";
+	if (metrics == XAPM_METRIC_SET_15)
+		return "Maximum Read Latency";
+	if (metrics == XAPM_METRIC_SET_16)
+		return "Transfer Cycle Count";
+	if (metrics == XAPM_METRIC_SET_17)
+		return "Packet Count";
+	if (metrics == XAPM_METRIC_SET_18)
+		return "Data Byte Count";
+	if (metrics == XAPM_METRIC_SET_19)
+		return "Position Byte Count";
+	if (metrics == XAPM_METRIC_SET_20)
+		return "Null Byte Count";
+	if (metrics == XAPM_METRIC_SET_21)
+		return "Slv_Idle_Cnt";
+	if (metrics == XAPM_METRIC_SET_22)
+		return "Mst_Idle_Cnt";
+	if (metrics == XAPM_METRIC_SET_30)
+		return "External event count";
+	return "Unsupported";
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets Write ID in Latency ID register to capture Write
+* Latency metrics.
+*
+* @param	writeid is the Write ID to be written in Latency ID register.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void setwriteid(u32 writeid)
+{
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_ID_OFFSET);
+		regval = regval & ~(XAPM_ID_WID_MASK);
+		regval = regval | writeid;
+		writereg(baseaddr, XAPM_ID_OFFSET, regval);
+	} else {
+		writereg(baseaddr, XAPM_ID_OFFSET, writeid);
+	}
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets Read ID in Latency ID register to capture
+* Read Latency metrics.
+*
+* @param	readid is the Read ID to be written in Latency ID register.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void setreadid(u32 readid)
+{
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_ID_OFFSET);
+		regval = regval & ~(XAPM_ID_RID_MASK);
+		regval = regval | (readid << 16);
+		writereg(baseaddr, XAPM_ID_OFFSET, regval);
+	} else {
+		writereg(baseaddr, XAPM_RID_OFFSET, readid);
+	}
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns Write ID in Latency ID register.
+*
+* @return	writeid is the required Write ID in Latency ID register.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getwriteid(void)
+{
+
+	u32 writeid;
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_ID_OFFSET);
+		writeid = regval & XAPM_ID_WID_MASK;
+	} else {
+		writeid = XAPM_IDMASK_OFFSET;
+	}
+
+	return writeid;
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns Read ID in Latency ID register.
+*
+* @return	readid is the required Read ID in Latency ID register.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getreadid(void)
+{
+
+	u32 readid;
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_ID_OFFSET);
+		regval = regval & XAPM_ID_RID_MASK;
+		readid = regval >> 16;
+	} else {
+		readid = XAPM_RID_OFFSET;
+	}
+
+	return readid;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets Latency Start point to calculate write latency.
+*
+* @param	Param can be 0 - XAPM_LATENCY_ADDR_ISSUE
+*		or 1 - XAPM_LATENCY_ADDR_ACCEPT
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void setwrlatencystart(u8 param)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	if (param == XAPM_LATENCY_ADDR_ACCEPT)
+		writereg(baseaddr, XAPM_CTL_OFFSET, regval |
+				XAPM_CR_WRLATENCY_START_MASK);
+	else
+		writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr,
+			XAPM_CTL_OFFSET) & ~(XAPM_CR_WRLATENCY_START_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets Latency End point to calculate write latency.
+*
+* @param	Param can be 0 - XAPM_LATENCY_LASTWR
+*		or 1 - XAPM_LATENCY_FIRSTWR
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void setwrlatencyend(u8 param)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	if (param == XAPM_LATENCY_FIRSTWR)
+		writereg(baseaddr, XAPM_CTL_OFFSET, regval |
+					XAPM_CR_WRLATENCY_END_MASK);
+	else
+		writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr,
+			XAPM_CTL_OFFSET) & ~(XAPM_CR_WRLATENCY_END_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets Latency Start point to calculate read latency.
+*
+* @param	Param can be 0 - XAPM_LATENCY_ADDR_ISSUE
+*		or 1 - XAPM_LATENCY_ADDR_ACCEPT
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void setrdlatencystart(u8 param)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	if (param == XAPM_LATENCY_ADDR_ACCEPT)
+		writereg(baseaddr, XAPM_CTL_OFFSET, regval |
+					XAPM_CR_RDLATENCY_START_MASK);
+	else
+		writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr,
+			XAPM_CTL_OFFSET) & ~(XAPM_CR_RDLATENCY_START_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets Latency End point to calculate read latency.
+*
+* @param	Param can be 0 - XAPM_LATENCY_LASTRD
+*		or 1 - XAPM_LATENCY_FIRSTRD
+* @return	None
+*
+* @note		None
+*
+******************************************************************************/
+void setrdlatencyend(u8 param)
+{
+	u32 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	if (param == XAPM_LATENCY_FIRSTRD)
+		writereg(baseaddr, XAPM_CTL_OFFSET, regval |
+				XAPM_CR_RDLATENCY_END_MASK);
+	else
+		writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr,
+			XAPM_CTL_OFFSET) & ~(XAPM_CR_RDLATENCY_END_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns Write Latency Start point.
+*
+* @return	Returns 0 - XAPM_LATENCY_ADDR_ISSUE or
+*			1 - XAPM_LATENCY_ADDR_ACCEPT
+*
+* @note		None
+*
+******************************************************************************/
+u8 getwrlatencystart(void)
+{
+	u8 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	regval = regval & XAPM_CR_WRLATENCY_START_MASK;
+	if (regval != XAPM_LATENCY_ADDR_ISSUE)
+		return XAPM_LATENCY_ADDR_ACCEPT;
+	else
+		return XAPM_LATENCY_ADDR_ISSUE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns Write Latency End point.
+*
+* @return	Returns 0 - XAPM_LATENCY_LASTWR or
+*			1 - XAPM_LATENCY_FIRSTWR.
+*
+* @note		None
+*
+******************************************************************************/
+u8 getwrlatencyend(void)
+{
+	u8 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	regval = regval & XAPM_CR_WRLATENCY_END_MASK;
+	if (regval != XAPM_LATENCY_LASTWR)
+		return XAPM_LATENCY_FIRSTWR;
+	else
+		return XAPM_LATENCY_LASTWR;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns read Latency Start point.
+*
+* @return	Returns 0 - XAPM_LATENCY_ADDR_ISSUE or
+*			1 - XAPM_LATENCY_ADDR_ACCEPT
+*
+* @note		None
+*
+******************************************************************************/
+u8 getrdlatencystart(void)
+{
+	u8 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	regval = regval & XAPM_CR_RDLATENCY_START_MASK;
+
+	if (regval != XAPM_LATENCY_ADDR_ISSUE)
+		return	XAPM_LATENCY_ADDR_ACCEPT;
+	else
+		return XAPM_LATENCY_ADDR_ISSUE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns Read Latency End point.
+*
+* @return	Returns 0 - XAPM_LATENCY_LASTRD or
+*			1 - XAPM_LATENCY_FIRSTRD.
+*
+* @note		None
+*
+******************************************************************************/
+u8 getrdlatencyend(void)
+{
+	u8 regval;
+
+	regval = readreg(baseaddr, XAPM_CTL_OFFSET);
+	regval = regval & XAPM_CR_RDLATENCY_END_MASK;
+	if (regval != XAPM_LATENCY_LASTRD)
+		return XAPM_LATENCY_FIRSTRD;
+	else
+		return XAPM_LATENCY_LASTRD;
+
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets Write ID Mask in ID Mask register.
+*
+* @param	wrmask is the Write ID mask to be written in ID register.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void setwriteidmask(u32 wrmask)
+{
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_IDMASK_OFFSET);
+		regval = regval & ~(XAPM_MASKID_WID_MASK);
+		regval = regval | wrmask;
+		writereg(baseaddr, XAPM_IDMASK_OFFSET, regval);
+	} else {
+		writereg(baseaddr, XAPM_IDMASK_OFFSET, wrmask);
+	}
+}
+
+/****************************************************************************/
+/**
+*
+* This function sets Read ID Mask in ID Mask register.
+*
+* @param	rdmask is the Read ID mask to be written in ID Mask register.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void setreadidmask(u32 rdmask)
+{
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_IDMASK_OFFSET);
+		regval = regval & ~(XAPM_MASKID_RID_MASK);
+		regval = regval | (rdmask << 16);
+		writereg(baseaddr, XAPM_IDMASK_OFFSET, regval);
+	} else {
+		writereg(baseaddr, XAPM_RIDMASK_OFFSET, rdmask);
+	}
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns Write ID Mask in ID Mask register.
+*
+* @return	wrmask is the required Write ID Mask in ID Mask register.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getwriteidmask(void)
+{
+
+	u32 wrmask;
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_IDMASK_OFFSET);
+		wrmask = regval & XAPM_MASKID_WID_MASK;
+	} else {
+		wrmask = XAPM_IDMASK_OFFSET;
+	}
+	return wrmask;
+}
+
+/****************************************************************************/
+/**
+*
+* This function returns Read ID Mask in ID Mask register.
+*
+* @return	rdmask is the required Read ID Mask in ID Mask register.
+*
+* @note		None.
+*
+*****************************************************************************/
+u32 getreadidmask(void)
+{
+
+	u32 rdmask;
+	u32 regval;
+
+	if (params->is_32bit_filter == 0) {
+		regval = readreg(baseaddr, XAPM_IDMASK_OFFSET);
+		regval = regval & XAPM_MASKID_RID_MASK;
+		rdmask = regval >> 16;
+	} else {
+		rdmask = XAPM_RIDMASK_OFFSET;
+	}
+	return rdmask;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/samples/xilinx_apm/xaxipmon.h
+++ linux-xilinx-zynqmp-5.15.0/samples/xilinx_apm/xaxipmon.h
@@ -0,0 +1,943 @@
+#ifndef XAXIPMON_H /* Prevent circular inclusions */
+#define XAXIPMON_H /* by using protection macros  */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include <stdint.h>
+#include <stdbool.h>
+
+
+#define XST_SUCCESS	0
+#define XST_FAILURE	1
+
+#ifndef TRUE
+#define TRUE		1
+#endif
+
+#ifndef FALSE
+#define FALSE		0
+#endif
+
+#ifndef NULL
+#define NULL		0
+#endif
+
+#define XAPM_GCC_HIGH_OFFSET		0x0000	/* Global Clock Counter
+							32 to 63 bits  */
+#define XAPM_GCC_LOW_OFFSET		0x0004	/* Global Clock Counter Lower
+							0-31 bits  */
+#define XAPM_SI_HIGH_OFFSET		0x0020	/* Sample Interval MSB */
+#define XAPM_SI_LOW_OFFSET		0x0024	/* Sample Interval LSB */
+#define XAPM_SICR_OFFSET		0x0028	/* Sample Interval Control
+							Register */
+#define XAPM_SR_OFFSET			0x002C	/* Sample Register */
+#define XAPM_GIE_OFFSET			0x0030	/* Global Interrupt Enable
+							Register */
+#define XAPM_IE_OFFSET			0x0034	/* Interrupt Enable Register */
+#define XAPM_IS_OFFSET			0x0038	/* Interrupt Status Register */
+
+#define XAPM_MSR0_OFFSET		0x0044	/* Metric Selector 0 Register*/
+#define XAPM_MSR1_OFFSET		0x0048	/* Metric Selector 1 Register*/
+#define XAPM_MSR2_OFFSET		0x004C	/* Metric Selector 2 Register*/
+
+#define XAPM_MC0_OFFSET			0x0100	/* Metric Counter 0 Register */
+#define XAPM_INC0_OFFSET		0x0104	/* Incrementer 0 Register */
+#define XAPM_RANGE0_OFFSET		0x0108	/* Range 0 Register */
+#define XAPM_MC0LOGEN_OFFSET		0x010C	/* Metric Counter 0
+							Log Enable Register */
+#define XAPM_MC1_OFFSET			0x0110	/* Metric Counter 1 Register */
+#define XAPM_INC1_OFFSET		0x0114	/* Incrementer 1 Register */
+#define XAPM_RANGE1_OFFSET		0x0118	/* Range 1 Register */
+#define XAPM_MC1LOGEN_OFFSET		0x011C	/* Metric Counter 1
+							Log Enable Register */
+#define XAPM_MC2_OFFSET			0x0120	/* Metric Counter 2 Register */
+#define XAPM_INC2_OFFSET		0x0124	/* Incrementer 2 Register */
+#define XAPM_RANGE2_OFFSET		0x0128	/* Range 2 Register */
+#define XAPM_MC2LOGEN_OFFSET		0x012C	/* Metric Counter 2
+							Log Enable Register */
+#define XAPM_MC3_OFFSET			0x0130	/* Metric Counter 3 Register */
+#define XAPM_INC3_OFFSET		0x0134	/* Incrementer 3 Register */
+#define XAPM_RANGE3_OFFSET		0x0138	/* Range 3 Register */
+#define XAPM_MC3LOGEN_OFFSET		0x013C	/* Metric Counter 3
+							Log Enable Register */
+#define XAPM_MC4_OFFSET			0x0140	/* Metric Counter 4 Register */
+#define XAPM_INC4_OFFSET		0x0144	/* Incrementer 4 Register */
+#define XAPM_RANGE4_OFFSET		0x0148	/* Range 4 Register */
+#define XAPM_MC4LOGEN_OFFSET		0x014C	/* Metric Counter 4
+							Log Enable Register */
+#define XAPM_MC5_OFFSET			0x0150	/* Metric Counter 5
+							Register */
+#define XAPM_INC5_OFFSET		0x0154	/* Incrementer 5 Register */
+#define XAPM_RANGE5_OFFSET		0x0158	/* Range 5 Register */
+#define XAPM_MC5LOGEN_OFFSET		0x015C	/* Metric Counter 5
+							Log Enable Register */
+#define XAPM_MC6_OFFSET			0x0160	/* Metric Counter 6
+							Register */
+#define XAPM_INC6_OFFSET		0x0164	/* Incrementer 6 Register */
+#define XAPM_RANGE6_OFFSET		0x0168	/* Range 6 Register */
+#define XAPM_MC6LOGEN_OFFSET		0x016C	/* Metric Counter 6
+							Log Enable Register */
+#define XAPM_MC7_OFFSET			0x0170	/* Metric Counter 7
+							Register */
+#define XAPM_INC7_OFFSET		0x0174	/* Incrementer 7 Register */
+#define XAPM_RANGE7_OFFSET		0x0178	/* Range 7 Register */
+#define XAPM_MC7LOGEN_OFFSET		0x017C	/* Metric Counter 7
+							Log Enable Register */
+#define XAPM_MC8_OFFSET			0x0180	/* Metric Counter 8
+							Register */
+#define XAPM_INC8_OFFSET		0x0184	/* Incrementer 8 Register */
+#define XAPM_RANGE8_OFFSET		0x0188	/* Range 8 Register */
+#define XAPM_MC8LOGEN_OFFSET		0x018C	/* Metric Counter 8
+							Log Enable Register */
+#define XAPM_MC9_OFFSET			0x0190	/* Metric Counter 9
+							Register */
+#define XAPM_INC9_OFFSET		0x0194	/* Incrementer 9 Register */
+#define XAPM_RANGE9_OFFSET		0x0198	/* Range 9 Register */
+#define XAPM_MC9LOGEN_OFFSET		0x019C	/* Metric Counter 9
+							Log Enable Register */
+
+#define XAPM_MC10_OFFSET		0x01A0	/* Metric Counter 10
+							Register */
+#define XAPM_MC11_OFFSET		0x01B0	/* Metric Counter 11
+							Register */
+#define XAPM_MC12_OFFSET		0x0500	/* Metric Counter 12
+							Register */
+#define XAPM_MC13_OFFSET		0x0510	/* Metric Counter 13
+							Register */
+#define XAPM_MC14_OFFSET		0x0520	/* Metric Counter 14
+							Register */
+#define XAPM_MC15_OFFSET		0x0530	/* Metric Counter 15
+							Register */
+#define XAPM_MC16_OFFSET		0x0540	/* Metric Counter 16
+							Register */
+#define XAPM_MC17_OFFSET		0x0550	/* Metric Counter 17
+							Register */
+#define XAPM_MC18_OFFSET		0x0560	/* Metric Counter 18
+							Register */
+#define XAPM_MC19_OFFSET		0x0570	/* Metric Counter 19
+							Register */
+#define XAPM_MC20_OFFSET		0x0580	/* Metric Counter 20
+							Register */
+#define XAPM_MC21_OFFSET		0x0590	/* Metric Counter 21
+							Register */
+#define XAPM_MC22_OFFSET		0x05A0	/* Metric Counter 22
+							Register */
+#define XAPM_MC23_OFFSET		0x05B0	/* Metric Counter 23
+							Register */
+#define XAPM_MC24_OFFSET		0x0700	/* Metric Counter 24
+							Register */
+#define XAPM_MC25_OFFSET		0x0710	/* Metric Counter 25
+							Register */
+#define XAPM_MC26_OFFSET		0x0720	/* Metric Counter 26
+							Register */
+#define XAPM_MC27_OFFSET		0x0730	/* Metric Counter 27
+							Register */
+#define XAPM_MC28_OFFSET		0x0740	/* Metric Counter 28
+							Register */
+#define XAPM_MC29_OFFSET		0x0750	/* Metric Counter 29
+							Register */
+#define XAPM_MC30_OFFSET		0x0760	/* Metric Counter 30
+							Register */
+#define XAPM_MC31_OFFSET		0x0770	/* Metric Counter 31
+							Register */
+#define XAPM_MC32_OFFSET		0x0780	/* Metric Counter 32
+							Register */
+#define XAPM_MC33_OFFSET		0x0790	/* Metric Counter 33
+							Register */
+#define XAPM_MC34_OFFSET		0x07A0	/* Metric Counter 34
+							Register */
+#define XAPM_MC35_OFFSET		0x07B0	/* Metric Counter 35
+							Register */
+#define XAPM_MC36_OFFSET		0x0900	/* Metric Counter 36
+							Register */
+#define XAPM_MC37_OFFSET		0x0910	/* Metric Counter 37
+							Register */
+#define XAPM_MC38_OFFSET		0x0920	/* Metric Counter 38
+							Register */
+#define XAPM_MC39_OFFSET		0x0930	/* Metric Counter 39
+							Register */
+#define XAPM_MC40_OFFSET		0x0940	/* Metric Counter 40
+							Register */
+#define XAPM_MC41_OFFSET		0x0950	/* Metric Counter 41
+							Register */
+#define XAPM_MC42_OFFSET		0x0960	/* Metric Counter 42
+							Register */
+#define XAPM_MC43_OFFSET		0x0970	/* Metric Counter 43
+							Register */
+#define XAPM_MC44_OFFSET		0x0980	/* Metric Counter 44
+							Register */
+#define XAPM_MC45_OFFSET		0x0990	/* Metric Counter 45
+							Register */
+#define XAPM_MC46_OFFSET		0x09A0	/* Metric Counter 46
+							Register */
+#define XAPM_MC47_OFFSET		0x09B0	/* Metric Counter 47
+							Register */
+
+#define XAPM_SMC0_OFFSET		0x0200	/* Sampled Metric Counter
+							0 Register */
+#define XAPM_SINC0_OFFSET		0x0204	/* Sampled Incrementer
+							0 Register */
+#define XAPM_SMC1_OFFSET		0x0210	/* Sampled Metric Counter
+							1 Register */
+#define XAPM_SINC1_OFFSET		0x0214	/* Sampled Incrementer
+							1 Register */
+#define XAPM_SMC2_OFFSET		0x0220	/* Sampled Metric Counter
+							2 Register */
+#define XAPM_SINC2_OFFSET		0x0224	/* Sampled Incrementer
+							2 Register */
+#define XAPM_SMC3_OFFSET		0x0230	/* Sampled Metric Counter
+							3 Register */
+#define XAPM_SINC3_OFFSET		0x0234	/* Sampled Incrementer
+							3 Register */
+#define XAPM_SMC4_OFFSET		0x0240	/* Sampled Metric Counter
+							4 Register */
+#define XAPM_SINC4_OFFSET		0x0244	/* Sampled Incrementer
+							4 Register */
+#define XAPM_SMC5_OFFSET		0x0250	/* Sampled Metric Counter
+							5 Register */
+#define XAPM_SINC5_OFFSET		0x0254	/* Sampled Incrementer
+							5 Register */
+#define XAPM_SMC6_OFFSET		0x0260	/* Sampled Metric Counter
+							6 Register */
+#define XAPM_SINC6_OFFSET		0x0264	/* Sampled Incrementer
+							6 Register */
+#define XAPM_SMC7_OFFSET		0x0270	/* Sampled Metric Counter
+							7 Register */
+#define XAPM_SINC7_OFFSET		0x0274	/* Sampled Incrementer
+							7 Register */
+#define XAPM_SMC8_OFFSET		0x0280	/* Sampled Metric Counter
+							8 Register */
+#define XAPM_SINC8_OFFSET		0x0284	/* Sampled Incrementer
+							8 Register */
+#define XAPM_SMC9_OFFSET		0x0290	/* Sampled Metric Counter
+							9 Register */
+#define XAPM_SINC9_OFFSET		0x0294	/* Sampled Incrementer
+							9 Register */
+#define XAPM_SMC10_OFFSET		0x02A0	/* Sampled Metric Counter
+							10 Register */
+#define XAPM_SMC11_OFFSET		0x02B0	/* Sampled Metric Counter
+							11 Register */
+#define XAPM_SMC12_OFFSET		0x0600	/* Sampled Metric Counter
+							12 Register */
+#define XAPM_SMC13_OFFSET		0x0610	/* Sampled Metric Counter
+							13 Register */
+#define XAPM_SMC14_OFFSET		0x0620	/* Sampled Metric Counter
+							14 Register */
+#define XAPM_SMC15_OFFSET		0x0630	/* Sampled Metric Counter
+							15 Register */
+#define XAPM_SMC16_OFFSET		0x0640	/* Sampled Metric Counter
+							16 Register */
+#define XAPM_SMC17_OFFSET		0x0650	/* Sampled Metric Counter
+							17 Register */
+#define XAPM_SMC18_OFFSET		0x0660	/* Sampled Metric Counter
+							18 Register */
+#define XAPM_SMC19_OFFSET		0x0670	/* Sampled Metric Counter
+							19 Register */
+#define XAPM_SMC20_OFFSET		0x0680	/* Sampled Metric Counter
+							20 Register */
+#define XAPM_SMC21_OFFSET		0x0690	/* Sampled Metric Counter
+							21 Register */
+#define XAPM_SMC22_OFFSET		0x06A0	/* Sampled Metric Counter
+							22 Register */
+#define XAPM_SMC23_OFFSET		0x06B0	/* Sampled Metric Counter
+							23 Register */
+#define XAPM_SMC24_OFFSET		0x0800	/* Sampled Metric Counter
+							24 Register */
+#define XAPM_SMC25_OFFSET		0x0810	/* Sampled Metric Counter
+							25 Register */
+#define XAPM_SMC26_OFFSET		0x0820	/* Sampled Metric Counter
+							26 Register */
+#define XAPM_SMC27_OFFSET		0x0830	/* Sampled Metric Counter
+							27 Register */
+#define XAPM_SMC28_OFFSET		0x0840	/* Sampled Metric Counter
+							28 Register */
+#define XAPM_SMC29_OFFSET		0x0850	/* Sampled Metric Counter
+							29 Register */
+#define XAPM_SMC30_OFFSET		0x0860	/* Sampled Metric Counter
+							30 Register */
+#define XAPM_SMC31_OFFSET		0x0870	/* Sampled Metric Counter
+							31 Register */
+#define XAPM_SMC32_OFFSET		0x0880	/* Sampled Metric Counter
+							32 Register */
+#define XAPM_SMC33_OFFSET		0x0890	/* Sampled Metric Counter
+							33 Register */
+#define XAPM_SMC34_OFFSET		0x08A0	/* Sampled Metric Counter
+							34 Register */
+#define XAPM_SMC35_OFFSET		0x08B0	/* Sampled Metric Counter
+							35 Register */
+#define XAPM_SMC36_OFFSET		0x0A00	/* Sampled Metric Counter
+							36 Register */
+#define XAPM_SMC37_OFFSET		0x0A10	/* Sampled Metric Counter
+							37 Register */
+#define XAPM_SMC38_OFFSET		0x0A20	/* Sampled Metric Counter
+							38 Register */
+#define XAPM_SMC39_OFFSET		0x0A30	/* Sampled Metric Counter
+							39 Register */
+#define XAPM_SMC40_OFFSET		0x0A40	/* Sampled Metric Counter
+							40 Register */
+#define XAPM_SMC41_OFFSET		0x0A50	/* Sampled Metric Counter
+							41 Register */
+#define XAPM_SMC42_OFFSET		0x0A60	/* Sampled Metric Counter
+							42 Register */
+#define XAPM_SMC43_OFFSET		0x0A70	/* Sampled Metric Counter
+							43 Register */
+#define XAPM_SMC44_OFFSET		0x0A80	/* Sampled Metric Counter
+							44 Register */
+#define XAPM_SMC45_OFFSET		0x0A90	/* Sampled Metric Counter
+							45 Register */
+#define XAPM_SMC46_OFFSET		0x0AA0	/* Sampled Metric Counter
+							46 Register */
+#define XAPM_SMC47_OFFSET		0x0AB0	/* Sampled Metric Counter
+							47 Register */
+
+#define XAPM_CTL_OFFSET			0x0300	/* Control Register */
+
+#define XAPM_ID_OFFSET			0x0304	/* Latency ID Register */
+
+#define XAPM_IDMASK_OFFSET		0x0308	/* ID Mask Register */
+
+#define XAPM_RID_OFFSET                 0x030C	/* Latency Write ID Register */
+
+#define XAPM_RIDMASK_OFFSET             0x0310	/* Read ID mask register */
+
+#define XAPM_FEC_OFFSET			0x0400	/* flag Enable
+							Control Register */
+
+#define XAPM_SWD_OFFSET			0x0404	/* Software-written
+							Data Register */
+
+#define XAPM_SICR_MCNTR_RST_MASK	0x00000100 /* Enable the Metric
+							Counter Reset */
+#define XAPM_SICR_LOAD_MASK		0x00000002 /* Load the Sample Interval
+							Register Value into
+							the counter */
+#define XAPM_SICR_ENABLE_MASK		0x00000001 /* Enable the downcounter */
+
+#define XAPM_IXR_MC9_OVERFLOW_MASK	0x00001000	/**< Metric Counter 9
+							  *  Overflow> */
+#define XAPM_IXR_MC8_OVERFLOW_MASK	0x00000800	/**< Metric Counter 8
+							  *  Overflow> */
+#define XAPM_IXR_MC7_OVERFLOW_MASK	0x00000400	/**< Metric Counter 7
+							  *  Overflow> */
+#define XAPM_IXR_MC6_OVERFLOW_MASK	0x00000200	/**< Metric Counter 6
+							  *  Overflow> */
+#define XAPM_IXR_MC5_OVERFLOW_MASK	0x00000100	/**< Metric Counter 5
+							  *  Overflow> */
+#define XAPM_IXR_MC4_OVERFLOW_MASK	0x00000080	/**< Metric Counter 4
+							  *  Overflow> */
+#define XAPM_IXR_MC3_OVERFLOW_MASK	0x00000040	/**< Metric Counter 3
+							  *  Overflow> */
+#define XAPM_IXR_MC2_OVERFLOW_MASK	0x00000020	/**< Metric Counter 2
+							  *  Overflow> */
+#define XAPM_IXR_MC1_OVERFLOW_MASK	0x00000010	/**< Metric Counter 1
+							  *  Overflow> */
+#define XAPM_IXR_MC0_OVERFLOW_MASK	0x00000008	/**< Metric Counter 0
+							  *  Overflow> */
+#define XAPM_IXR_FIFO_FULL_MASK		0x00000004	/**< Event Log FIFO
+							  *  full> */
+#define XAPM_IXR_SIC_OVERFLOW_MASK	0x00000002	/**< Sample Interval
+							  * Counter Overflow */
+#define XAPM_IXR_GCC_OVERFLOW_MASK	0x00000001	/**< Global Clock
+							Counter Overflow */
+#define XAPM_IXR_ALL_MASK		(XAPM_IXR_SIC_OVERFLOW_MASK | \
+					XAPM_IXR_GCC_OVERFLOW_MASK |  \
+					XAPM_IXR_FIFO_FULL_MASK | \
+					XAPM_IXR_MC0_OVERFLOW_MASK | \
+					XAPM_IXR_MC1_OVERFLOW_MASK | \
+					XAPM_IXR_MC2_OVERFLOW_MASK | \
+					XAPM_IXR_MC3_OVERFLOW_MASK | \
+					XAPM_IXR_MC4_OVERFLOW_MASK | \
+					XAPM_IXR_MC5_OVERFLOW_MASK | \
+					XAPM_IXR_MC6_OVERFLOW_MASK | \
+					XAPM_IXR_MC7_OVERFLOW_MASK | \
+					XAPM_IXR_MC8_OVERFLOW_MASK | \
+					XAPM_IXR_MC9_OVERFLOW_MASK)
+
+#define XAPM_CR_FIFO_RESET_MASK			0x02000000
+						/**< FIFO Reset */
+#define XAPM_CR_MUXSEL_MASK			0x01000000
+						/**< Mux Selector mask */
+#define XAPM_CR_GCC_RESET_MASK			0x00020000
+						/**< Global Clk
+						  Counter Reset */
+#define XAPM_CR_GCC_ENABLE_MASK			0x00010000
+						/**< Global Clk
+						   Counter Enable */
+#define XAPM_CR_EVTLOG_EXTTRIGGER_MASK		0x00000200
+						/**< Enable External trigger
+						to start event Log */
+#define XAPM_CR_EVENTLOG_ENABLE_MASK		0x00000100
+						/**< Event Log Enable */
+#define XAPM_CR_RDLATENCY_END_MASK		0x00000080
+						/**< Write Latency
+							End point */
+#define XAPM_CR_RDLATENCY_START_MASK		0x00000040
+						/**< Read Latency
+							Start point */
+#define XAPM_CR_WRLATENCY_END_MASK		0x00000020
+						/**< Write Latency
+							End point */
+#define XAPM_CR_WRLATENCY_START_MASK		0x00000010
+						/**< Write Latency
+							Start point */
+#define XAPM_CR_IDFILTER_ENABLE_MASK		0x00000008
+						/**< ID Filter Enable */
+#define XAPM_CR_MCNTR_EXTTRIGGER_MASK		0x00000004
+						/**< Enable External
+						   trigger to start
+						   Metric Counters  */
+#define XAPM_CR_MCNTR_RESET_MASK		0x00000002
+						/**< Metrics Counter
+						   Reset */
+#define XAPM_CR_MCNTR_ENABLE_MASK		0x00000001
+						/**< Metrics Counter
+							Enable */
+
+#define XAPM_ID_RID_MASK			0xFFFF0000 /**< Read ID */
+
+#define XAPM_ID_WID_MASK			0x0000FFFF /**< Write ID */
+
+#define XAPM_MASKID_RID_MASK			0xFFFF0000 /**< Read ID Mask */
+
+#define XAPM_MASKID_WID_MASK			0x0000FFFF /**< Write ID Mask*/
+
+
+#define XAPM_MAX_COUNTERS		10 /**< Maximum number of Counters */
+#define XAPM_MAX_COUNTERS_PROFILE	48 /**< Maximum number of Counters in
+						profile mode */
+
+#define XAPM_METRIC_COUNTER_0	0 /**< Metric Counter 0 Register Index */
+#define XAPM_METRIC_COUNTER_1	1 /**< Metric Counter 1 Register Index */
+#define XAPM_METRIC_COUNTER_2	2 /**< Metric Counter 2 Register Index */
+#define XAPM_METRIC_COUNTER_3	3 /**< Metric Counter 3 Register Index */
+#define XAPM_METRIC_COUNTER_4	4 /**< Metric Counter 4 Register Index */
+#define XAPM_METRIC_COUNTER_5	5 /**< Metric Counter 5 Register Index */
+#define XAPM_METRIC_COUNTER_6	6 /**< Metric Counter 6 Register Index */
+#define XAPM_METRIC_COUNTER_7	7 /**< Metric Counter 7 Register Index */
+#define XAPM_METRIC_COUNTER_8	8 /**< Metric Counter 8 Register Index */
+#define XAPM_METRIC_COUNTER_9	9 /**< Metric Counter 9 Register Index */
+
+#define XAPM_INCREMENTER_0	0 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_1	1 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_2	2 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_3	3 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_4	4 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_5	5 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_6	6 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_7	7 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_8	8 /**< Metric Counter 0 Register Index */
+#define XAPM_INCREMENTER_9	9 /**< Metric Counter 0 Register Index */
+
+#define XAPM_METRIC_SET_0	0 /**< Write Transaction Count */
+#define XAPM_METRIC_SET_1	1 /**< Read Transaction Count */
+#define XAPM_METRIC_SET_2	2 /**< Write Byte Count */
+#define XAPM_METRIC_SET_3	3 /**< Read Byte Count */
+#define XAPM_METRIC_SET_4	4 /**< Write Beat Count */
+#define XAPM_METRIC_SET_5	5 /**< Total Read Latency */
+#define XAPM_METRIC_SET_6	6 /**< Total Write Latency */
+#define XAPM_METRIC_SET_7	7 /**< Slv_Wr_Idle_Cnt */
+#define XAPM_METRIC_SET_8	8 /**< Mst_Rd_Idle_Cnt */
+#define XAPM_METRIC_SET_9	9 /**< Num_BValids */
+#define XAPM_METRIC_SET_10	10 /**< Num_WLasts */
+#define XAPM_METRIC_SET_11	11 /**< Num_RLasts */
+#define XAPM_METRIC_SET_12	12 /**< Minimum Write Latency */
+#define XAPM_METRIC_SET_13	13 /**< Maximum Write Latency */
+#define XAPM_METRIC_SET_14	14 /**< Minimum Read Latency */
+#define XAPM_METRIC_SET_15	15 /**< Maximum Read Latency */
+#define XAPM_METRIC_SET_16	16 /**< Transfer Cycle Count */
+#define XAPM_METRIC_SET_17	17 /**< Packet Count */
+#define XAPM_METRIC_SET_18	18 /**< Data Byte Count */
+#define XAPM_METRIC_SET_19	19 /**< Position Byte Count */
+#define XAPM_METRIC_SET_20	20 /**< Null Byte Count */
+#define XAPM_METRIC_SET_21	21 /**< Slv_Idle_Cnt */
+#define XAPM_METRIC_SET_22	22 /**< Mst_Idle_Cnt */
+#define XAPM_METRIC_SET_30	30 /**< External event count */
+
+#define XAPM_MAX_AGENTS		8 /**< Maximum number of Agents */
+
+#define XAPM_FLAG_WRADDR	0x00000001 /**< Write Address flag */
+#define XAPM_FLAG_FIRSTWR	0x00000002 /**< First Write flag */
+#define XAPM_FLAG_LASTWR	0x00000004 /**< Last Write flag */
+#define XAPM_FLAG_RESPONSE	0x00000008 /**< Response flag */
+#define XAPM_FLAG_RDADDR	0x00000010 /**< Read Address flag */
+#define XAPM_FLAG_FIRSTRD	0x00000020 /**< First Read flag */
+#define XAPM_FLAG_LASTRD	0x00000040 /**< Last Read flag */
+#define XAPM_FLAG_SWDATA	0x00010000 /**< Software-written Data flag */
+#define XAPM_FLAG_EVENT		0x00020000 /**< Last Read flag */
+#define XAPM_FLAG_EVNTSTOP	0x00040000 /**< Last Read flag */
+#define XAPM_FLAG_EVNTSTART	0x00080000 /**< Last Read flag */
+#define XAPM_FLAG_GCCOVF	0x00100000 /**< Global Clock Counter Overflow
+					     *  flag */
+#define XAPM_FLAG_SCLAPSE	0x00200000 /**< Sample Counter Lapse flag */
+#define XAPM_FLAG_MC0		0x00400000 /**< Metric Counter 0 flag */
+#define XAPM_FLAG_MC1		0x00800000 /**< Metric Counter 1 flag */
+#define XAPM_FLAG_MC2		0x01000000 /**< Metric Counter 2 flag */
+#define XAPM_FLAG_MC3		0x02000000 /**< Metric Counter 3 flag */
+#define XAPM_FLAG_MC4		0x04000000 /**< Metric Counter 4 flag */
+#define XAPM_FLAG_MC5		0x08000000 /**< Metric Counter 5 flag */
+#define XAPM_FLAG_MC6		0x10000000 /**< Metric Counter 6 flag */
+#define XAPM_FLAG_MC7		0x20000000 /**< Metric Counter 7 flag */
+#define XAPM_FLAG_MC8		0x40000000 /**< Metric Counter 8 flag */
+#define XAPM_FLAG_MC9		0x80000000 /**< Metric Counter 9 flag */
+
+#define XAPM_LATENCY_ADDR_ISSUE		0 /**< Address Issue as start
+					point for Latency calculation*/
+#define XAPM_LATENCY_ADDR_ACCEPT	1 /**< Address Acceptance as start
+					point for Latency calculation*/
+#define XAPM_LATENCY_LASTRD		0 /**< Last Read as end point for
+					Latency calculation */
+#define XAPM_LATENCY_LASTWR		0 /**< Last Write as end point for
+					Latency calculation */
+#define XAPM_LATENCY_FIRSTRD		1 /**< First Read as end point for
+					Latency calculation */
+#define XAPM_LATENCY_FIRSTWR		1 /**< First Write as end point for
+					Latency calculation */
+
+#define XAPM_MODE_TRACE			2 /**< APM in Trace mode */
+
+#define XAPM_MODE_PROFILE		1 /**< APM in Profile mode */
+
+#define XAPM_MODE_ADVANCED		0 /**< APM in Advanced mode */
+
+typedef unsigned char u8;
+typedef uint16_t u16;
+typedef uint32_t u32;
+typedef unsigned long ulong;
+
+ulong baseaddr;
+
+struct xapm_param {
+	u32	mode;
+	u32	maxslots;
+	u32	eventcnt;
+	u32	eventlog;
+	u32	sampledcnt;
+	u32	numcounters;
+	u32	metricwidth;
+	u32	sampledwidth;
+	u32	globalcntwidth;
+	u32     scalefactor;
+	u32	isr;
+	bool	is_32bit_filter;
+};
+
+static struct xapm_param *params;
+
+/*****************************************************************************/
+/**
+*
+* Read a register of the AXI Performance Monitor device. This macro provides
+* register access to all registers using the register offsets defined above.
+*
+* @param	baseaddr contains the base address of the device.
+* @param	regoffset is the offset of the register to read.
+*
+* @return	The contents of the register.
+*
+* @note		C-style Signature:
+*		u32 readreg(u32 baseaddr, u32 regoffset);
+*
+******************************************************************************/
+#define readreg(baseaddr, regoffset) \
+			(*(u32 *)(baseaddr + regoffset))
+
+/*****************************************************************************/
+/**
+*
+* Write a register of the AXI Performance Monitor device. This macro provides
+* register access to all registers using the register offsets defined above.
+*
+* @param	baseaddr contains the base address of the device.
+* @param	regoffset is the offset of the register to write.
+* @param	data is the value to write to the register.
+*
+* @return	None.
+*
+* @note		C-style Signature:
+*		void writereg(u32 baseaddr,
+*					u32 regoffset,u32 Data)
+*
+******************************************************************************/
+#define writereg(baseaddr, regoffset, data) \
+				(*(u32 *)(baseaddr + regoffset) = data)
+
+/****************************************************************************/
+/**
+*
+* This routine enables the Global Interrupt.
+*
+* @note		C-Style signature:
+*		void intrglobalenable()
+*
+*****************************************************************************/
+#define intrglobalenable()			\
+		writereg(baseaddr, XAPM_GIE_OFFSET, 1)
+
+
+/****************************************************************************/
+/**
+*
+* This routine disables the Global Interrupt.
+*
+* @note		C-Style signature:
+*		void intrglobaldisable(void)
+*
+*****************************************************************************/
+#define intrglobaldisable()				\
+		writereg(baseaddr, XAPM_GIE_OFFSET, 0)
+
+/****************************************************************************/
+/**
+*
+* This routine enables interrupt(s). Use the XAPM_IXR_* constants defined in
+* xaxipmon_hw.h to create the bit-mask to enable interrupts.
+*
+* @param	mask is the mask to enable. Bit positions of 1 will be enabled.
+*		Bit positions of 0 will keep the previous setting. This mask is
+*		formed by OR'ing XAPM_IXR__* bits defined in xaxipmon_hw.h.
+*
+* @return	None.
+*
+* @note		C-Style signature:
+*		void intrenable(u32 mask)
+*
+*****************************************************************************/
+#define intrenable(mask)				     \
+	writereg(baseaddr, XAPM_IE_OFFSET, readreg(baseaddr, \
+			XAPM_IE_OFFSET) | mask);
+
+
+/****************************************************************************/
+/**
+*
+* This routine disable interrupt(s). Use the XAPM_IXR_* constants defined in
+* xaxipmon_hw.h to create the bit-mask to disable interrupts.
+*
+* @param	mask is the mask to disable. Bit positions of 1 will be
+*		disabled. Bit positions of 0 will keep the previous setting.
+*		This mask is formed by OR'ing XAPM_IXR_* bits defined in
+*		xaxipmon_hw.h.
+*
+* @return	None.
+*
+* @note		C-Style signature:
+*		void intrdisable(u32 mask)
+*
+*****************************************************************************/
+#define intrdisable(mask)				     \
+	writereg(baseaddr, XAPM_IE_OFFSET, readreg(baseaddr, \
+						XAPM_IE_OFFSET) | mask);
+
+/****************************************************************************/
+/**
+*
+* This routine clears the specified interrupt(s).
+*
+* @param	mask is the mask to clear. Bit positions of 1 will be cleared.
+*		This mask is formed by OR'ing XAPM_IXR_* bits defined in
+*		xaxipmon_hw.h.
+*
+* @return	None.
+*
+* @note		C-Style signature:
+*		void intrclear(u32 mask)
+*
+*****************************************************************************/
+#define intrclear(mask)				     \
+	writereg(baseaddr, XAPM_IS_OFFSET, readreg(baseaddr, \
+				XAPM_IS_OFFSET) | mask);
+
+/****************************************************************************/
+/**
+*
+* This routine returns the Interrupt Status Register.
+*
+* @return	isr value updated by kernel driver
+*
+* @note		This macro returns isr value updated by kernel driver.
+*		C-Style signature:
+*		void intrgetstatus(void)
+*
+*****************************************************************************/
+#define intrgetstatus()		(params->isr)
+
+/****************************************************************************/
+/**
+*
+* This routine returns the Interrupt Status Register.
+*
+* @return       Interrupt Status Register contents
+*
+* @note         C-Style signature:
+*               void intrhwgetstatus(void)
+*
+*****************************************************************************/
+#define intrhwgetstatus()         (params->isr)
+
+/****************************************************************************/
+/**
+*
+* This function enables the Global Clock Counter.
+*
+* @note		C-Style signature:
+*		void enablegcc(void);
+*
+*****************************************************************************/
+#define enablegcc() \
+	writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr, \
+			XAPM_CTL_OFFSET) | XAPM_CR_GCC_ENABLE_MASK);
+
+/****************************************************************************/
+/**
+*
+* This function disbles the Global Clock Counter.
+*
+* @note		C-Style signature:
+*		void disablegcc(void);
+*
+*****************************************************************************/
+#define disablegcc() \
+	writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr, \
+			XAPM_CTL_OFFSET) & ~(XAPM_CR_GCC_ENABLE_MASK));
+
+/****************************************************************************/
+/**
+*
+* This function enables the specified flag in flag Control Register.
+*
+* @param	flag is one of the XAPM_FLAG_* masks defined in xaxipmon.h
+*
+* @return	None
+*
+* @note		C-Style signature:
+*		void enableflag(void);
+*
+*****************************************************************************/
+#define enableflag(flag) \
+	writereg(baseaddr, XAPM_FEC_OFFSET, \
+			readreg(baseaddr, XAPM_FEC_OFFSET) | flag);
+
+/****************************************************************************/
+/**
+*
+* This function disables the specified flag in flag Control Register.
+*
+* @param	flag is one of the XAPM_FLAG_* masks defined in xaxipmon.h*
+* @return	None
+*
+* @note		C-Style signature:
+*		void disableflag(void);
+*
+*****************************************************************************/
+#define disableflag(flag) \
+	writereg(baseaddr, XAPM_FEC_OFFSET, \
+			readreg(baseaddr, XAPM_FEC_OFFSET) & ~(flag));
+
+/****************************************************************************/
+/**
+*
+* This function loads the sample interval register value into the sample
+* interval counter.
+*
+* @note		C-Style signature:
+*		void loadsic(void);
+*
+*****************************************************************************/
+#define loadsic() \
+		writereg(baseaddr, XAPM_SICR_OFFSET, XAPM_SICR_LOAD_MASK)
+
+
+/****************************************************************************/
+/**
+*
+* This enables the down count of the sample interval counter.
+*
+* @note		C-Style signature:
+*	   void enablesic(void);
+*
+*****************************************************************************/
+#define enablesic() \
+	writereg(baseaddr, XAPM_SICR_OFFSET, XAPM_SICR_ENABLE_MASK)
+
+/****************************************************************************/
+/**
+*
+* This disables the down count of the sample interval counter.
+*
+* @note		C-Style signature:
+*	    void disablesic(void);
+*
+*****************************************************************************/
+#define disablesic() \
+	writereg(baseaddr, XAPM_SICR_OFFSET, \
+	readreg(baseaddr, XAPM_SICR_OFFSET) & ~(XAPM_SICR_ENABLE_MASK));
+
+/****************************************************************************/
+/**
+*
+* This enables Reset of Metric Counters when Sample Interval Counter lapses.
+*
+* @note		C-Style signature:
+*		void enablemcreset(void);
+*
+*****************************************************************************/
+#define enablemcreset() \
+	writereg(baseaddr, XAPM_SICR_OFFSET, XAPM_SICR_MCNTR_RST_MASK);
+
+/****************************************************************************/
+/**
+*
+* This disables the down count of the sample interval counter.
+*
+* @note		C-Style signature:
+*		void disablemcreset(void);
+*
+*****************************************************************************/
+#define disablemcreset() \
+	writereg(baseaddr, XAPM_SICR_OFFSET, \
+	readreg(baseaddr, XAPM_SICR_OFFSET) & ~(XAPM_SICR_MCNTR_RST_MASK));
+
+/****************************************************************************/
+/**
+*
+* This function enables the ID Filter Masking.
+*
+* @note		C-Style signature:
+*		void enableidfilter(void);
+*
+*****************************************************************************/
+#define enableidfilter()			\
+	writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr, \
+			XAPM_CTL_OFFSET) | XAPM_CR_IDFILTER_ENABLE_MASK);
+
+/****************************************************************************/
+/**
+*
+* This function disbles the ID Filter masking.
+*
+* @note		C-Style signature:
+*		void disableidfilter(void);
+*
+*****************************************************************************/
+#define disableidfilter() \
+	writereg(baseaddr, XAPM_CTL_OFFSET, readreg(baseaddr, \
+			XAPM_CTL_OFFSET) & ~(XAPM_CR_IDFILTER_ENABLE_MASK));
+
+/****************************************************************************/
+/**
+*
+* This function samples Metric Counters to Sampled Metric Counters by
+* reading Sample Register and also returns interval. i.e. the number of
+* clocks in between previous read to the current read of sample register.
+*
+* @return	Interval. i.e. the number of clocks in between previous
+*		read to the current read of sample register.
+*
+* @note		C-Style signature:
+*		u32 samplemetrics(void);
+*
+*****************************************************************************/
+#define samplemetrics()		readreg(baseaddr, XAPM_SR_OFFSET);
+
+
+/************************** Function Prototypes *****************************/
+
+int resetmetriccounter(void);
+
+void resetglobalclkcounter(void);
+
+int resetfifo(void);
+
+void setincrementerrange(u8 incrementer, u16 rangehigh, u16 rangelow);
+
+void getincrementerrange(u8 incrementer, u16 *rangehigh, u16 *rangelow);
+
+void setsampleinterval(u32 sampleinterval);
+
+void getsampleinterval(u32 *sampleinterval);
+
+int setmetrics(u8 slot, u8 metrics, u8 counter);
+
+int getmetrics(u8 counter, u8 *metrics, u8 *slot);
+void getglobalclkcounter(u32 *cnthigh, u32 *cntlow);
+
+u32 getmetriccounter(u32 counter);
+
+u32 getsampledmetriccounter(u32 counter);
+
+u32 getincrementer(u32 incrementer);
+
+u32 getsampledincrementer(u32 incrementer);
+
+void setswdatareg(u32 swdata);
+
+u32 getswdatareg(void);
+
+int starteventlog(u32 flagenables);
+
+int stopeventlog(void);
+
+int startcounters(u32 sampleinterval);
+
+int stopcounters(void);
+
+void enablemetricscounter(void);
+
+void disablemetricscounter(void);
+
+void setlogenableranges(u32 counter, u16 rangehigh, u16 rangelow);
+
+void getlogenableranges(u32 counter, u16 *rangehigh, u16 *rangelow);
+
+void enableeventlog(void);
+
+void enablemctrigger(void);
+
+void disablemctrigger(void);
+
+void enableeventlogtrigger(void);
+
+void disableeventlogtrigger(void);
+
+const char *getmetricname(u8 metrics);
+
+void setwriteid(u32 writeid);
+
+void setreadid(u32 readid);
+
+u32 getwriteid(void);
+
+u32 getreadid(void);
+
+void setwrlatencystart(u8 param);
+
+void setwrlatencyend(u8 param);
+
+void setrdlatencystart(u8 param);
+
+void setrdlatencyend(u8 param);
+
+u8 getwrlatencystart(void);
+
+u8 getwrlatencyend(void);
+
+u8 getrdlatencystart(void);
+
+u8 getrdlatencyend(void);
+
+void setwriteidmask(u32 wrmask);
+
+void setreadidmask(u32 rdmask);
+
+u32 getwriteidmask(void);
+
+u32 getreadidmask(void);
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif  /* End of protection macro. */
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Kbuild.include
+++ linux-xilinx-zynqmp-5.15.0/scripts/Kbuild.include
@@ -96,8 +96,29 @@
  quiet_redirect :=
 silent_redirect := exec >/dev/null;
 
+# Delete the target on interruption
+#
+# GNU Make automatically deletes the target if it has already been changed by
+# the interrupted recipe. So, you can safely stop the build by Ctrl-C (Make
+# will delete incomplete targets), and resume it later.
+#
+# However, this does not work when the stderr is piped to another program, like
+#  $ make >&2 | tee log
+# Make dies with SIGPIPE before cleaning the targets.
+#
+# To address it, we clean the target in signal traps.
+#
+# Make deletes the target when it catches SIGHUP, SIGINT, SIGQUIT, SIGTERM.
+# So, we cover them, and also SIGPIPE just in case.
+#
+# Of course, this is unneeded for phony targets.
+delete-on-interrupt = \
+	$(if $(filter-out $(PHONY), $@), \
+		$(foreach sig, HUP INT QUIT TERM PIPE, \
+			trap 'rm -f $@; trap - $(sig); kill -s $(sig) $$$$' $(sig);))
+
 # printing commands
-cmd = @set -e; $(echo-cmd) $($(quiet)redirect) $(cmd_$(1))
+cmd = @set -e; $(echo-cmd) $($(quiet)redirect) $(delete-on-interrupt) $(cmd_$(1))
 
 ###
 # if_changed      - execute command if any prerequisite is newer than
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile
@@ -3,8 +3,8 @@
 # scripts contains sources for various helper programs used throughout
 # the kernel for the build process.
 
-CRYPTO_LIBS = $(shell pkg-config --libs libcrypto 2> /dev/null || echo -lcrypto)
-CRYPTO_CFLAGS = $(shell pkg-config --cflags libcrypto 2> /dev/null)
+CRYPTO_LIBS = $(shell $(HOSTPKG_CONFIG) --libs libcrypto 2> /dev/null || echo -lcrypto)
+CRYPTO_CFLAGS = $(shell $(HOSTPKG_CONFIG) --cflags libcrypto 2> /dev/null)
 
 hostprogs-always-$(CONFIG_BUILD_BIN2C)			+= bin2c
 hostprogs-always-$(CONFIG_KALLSYMS)			+= kallsyms
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.build
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.build
@@ -224,6 +224,18 @@
 endif # CONFIG_FTRACE_MCOUNT_USE_RECORDMCOUNT
 
 ifdef CONFIG_STACK_VALIDATION
+
+objtool_args =								\
+	$(if $(CONFIG_UNWINDER_ORC),orc generate,check)			\
+	$(if $(part-of-module), --module)				\
+	$(if $(CONFIG_FRAME_POINTER),, --no-fp)				\
+	$(if $(CONFIG_GCOV_KERNEL)$(CONFIG_LTO_CLANG), --no-unreachable)\
+	$(if $(CONFIG_RETPOLINE), --retpoline)				\
+	$(if $(CONFIG_RETHUNK), --rethunk)				\
+	$(if $(CONFIG_X86_SMAP), --uaccess)				\
+	$(if $(CONFIG_FTRACE_MCOUNT_USE_OBJTOOL), --mcount)		\
+	$(if $(CONFIG_SLS), --sls)
+
 ifndef CONFIG_LTO_CLANG
 
 __objtool_obj := $(objtree)/tools/objtool/objtool
@@ -254,6 +266,12 @@
 undefined_syms = $(NM) $< | $(AWK) '$$1 == "U" { printf("%s%s", x++ ? " " : "", $$2) }';
 endif
 
+ifdef CONFIG_RETPOLINE
+cmd_ubuntu_retpoline = $(CONFIG_SHELL) $(srctree)/scripts/ubuntu-retpoline-extract-one $(@) $(<) "$(filter -m16 %code16gcc.h,$(a_flags))";
+else
+cmd_ubuntu_retpoline =
+endif
+
 define rule_cc_o_c
 	$(call cmd_and_fixdep,cc_o_c)
 	$(call cmd,gen_ksymdeps)
@@ -261,6 +279,7 @@
 	$(call cmd,checkdoc)
 	$(call cmd,objtool)
 	$(call cmd,modversions_c)
+	$(call cmd,ubuntu-retpoline)
 	$(call cmd,record_mcount)
 endef
 
@@ -269,6 +288,7 @@
 	$(call cmd,gen_ksymdeps)
 	$(call cmd,objtool)
 	$(call cmd,modversions_S)
+	$(call cmd,ubuntu-retpoline)
 endef
 
 # Built-in and composite module parts
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.compiler
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.compiler
@@ -68,7 +68,3 @@
 # ld-option
 # Usage: KBUILD_LDFLAGS += $(call ld-option, -X, -Y)
 ld-option = $(call try-run, $(LD) $(KBUILD_LDFLAGS) $(1) -v,$(1),$(2),$(3))
-
-# ld-ifversion
-# Usage:  $(call ld-ifversion, -ge, 22252, y)
-ld-ifversion = $(shell [ $(CONFIG_LD_VERSION)0 $(1) $(2)0 ] && echo $(3) || echo $(4))
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.dtbinst
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.dtbinst
@@ -24,7 +24,7 @@
 	@:
 
 quiet_cmd_dtb_install = INSTALL $@
-      cmd_dtb_install = install -D $< $@
+      cmd_dtb_install = install -D -m 0644 $< $@
 
 $(dst)/%.dtb: $(obj)/%.dtb
 	$(call cmd,dtb_install)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.extrawarn
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.extrawarn
@@ -37,6 +37,10 @@
 KBUILD_CFLAGS += -Wno-sign-compare
 KBUILD_CFLAGS += -Wno-type-limits
 
+ifdef CONFIG_CC_IS_CLANG
+KBUILD_CFLAGS += -Wno-enum-enum-conversion
+endif
+
 KBUILD_CPPFLAGS += -DKBUILD_EXTRA_WARN1
 
 else
@@ -51,6 +55,9 @@
 KBUILD_CFLAGS += -Wno-format-zero-length
 KBUILD_CFLAGS += $(call cc-disable-warning, pointer-to-enum-cast)
 KBUILD_CFLAGS += -Wno-tautological-constant-out-of-range-compare
+KBUILD_CFLAGS += $(call cc-disable-warning, unaligned-access)
+KBUILD_CFLAGS += $(call cc-disable-warning, cast-function-type-strict)
+KBUILD_CFLAGS += -Wno-enum-compare-conditional
 endif
 
 endif
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.gcc-plugins
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.gcc-plugins
@@ -6,7 +6,7 @@
 gcc-plugin-cflags-$(CONFIG_GCC_PLUGIN_LATENT_ENTROPY)		\
 		+= -DLATENT_ENTROPY_PLUGIN
 ifdef CONFIG_GCC_PLUGIN_LATENT_ENTROPY
-    DISABLE_LATENT_ENTROPY_PLUGIN += -fplugin-arg-latent_entropy_plugin-disable
+    DISABLE_LATENT_ENTROPY_PLUGIN += -fplugin-arg-latent_entropy_plugin-disable -ULATENT_ENTROPY_PLUGIN
 endif
 export DISABLE_LATENT_ENTROPY_PLUGIN
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.lib
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.lib
@@ -232,17 +232,6 @@
 mod-prelink-ext := .lto
 endif
 
-# Objtool arguments are also needed for modfinal with LTO, so we define
-# then here to avoid duplication.
-objtool_args =								\
-	$(if $(CONFIG_UNWINDER_ORC),orc generate,check)			\
-	$(if $(part-of-module), --module)				\
-	$(if $(CONFIG_FRAME_POINTER),, --no-fp)				\
-	$(if $(CONFIG_GCOV_KERNEL)$(CONFIG_LTO_CLANG), --no-unreachable)\
-	$(if $(CONFIG_RETPOLINE), --retpoline)				\
-	$(if $(CONFIG_X86_SMAP), --uaccess)				\
-	$(if $(CONFIG_FTRACE_MCOUNT_USE_OBJTOOL), --mcount)
-
 # Useful for describing the dependency of composite objects
 # Usage:
 #   $(call multi_depend, multi_used_targets, suffix_to_remove, suffix_to_add)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.modfinal
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.modfinal
@@ -23,7 +23,7 @@
 part-of-module = y
 
 quiet_cmd_cc_o_c = CC [M]  $@
-      cmd_cc_o_c = $(CC) $(filter-out $(CC_FLAGS_CFI), $(c_flags)) -c -o $@ $<
+      cmd_cc_o_c = $(CC) $(filter-out $(CC_FLAGS_CFI) $(CFLAGS_GCOV) $(CFLAGS_KCSAN), $(c_flags)) -c -o $@ $<
 
 %.mod.o: %.mod.c FORCE
 	$(call if_changed_dep,cc_o_c)
@@ -40,7 +40,7 @@
 quiet_cmd_btf_ko = BTF [M] $@
       cmd_btf_ko = 							\
 	if [ -f vmlinux ]; then						\
-		LLVM_OBJCOPY="$(OBJCOPY)" $(PAHOLE) -J --btf_base vmlinux $@; \
+		LLVM_OBJCOPY="$(OBJCOPY)" $(PAHOLE) -J $(PAHOLE_FLAGS) --btf_base vmlinux $@; \
 	else								\
 		printf "Skipping BTF generation for %s due to unavailability of vmlinux\n" $@ 1>&2; \
 	fi;
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.modinst
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.modinst
@@ -67,9 +67,11 @@
 #
 ifeq ($(CONFIG_MODULE_SIG_ALL),y)
 quiet_cmd_sign = SIGN    $@
-$(eval $(call config_filename,MODULE_SIG_KEY))
-      cmd_sign = scripts/sign-file $(CONFIG_MODULE_SIG_HASH) $(MODULE_SIG_KEY_SRCPREFIX)$(CONFIG_MODULE_SIG_KEY) certs/signing_key.x509 $@ \
-                 $(if $(KBUILD_EXTMOD),|| true)
+      cmd_sign = if test -e $(srctree)/debian/scripts/sign-module && \
+                    $(srctree)/debian/scripts/sign-module $@ ; \
+                 then scripts/sign-file $(CONFIG_MODULE_SIG_HASH) $(MODULE_SIG_KEY_SRCPREFIX)$(CONFIG_MODULE_SIG_KEY) certs/signing_key.x509 $@ \
+                      $(if $(KBUILD_EXTMOD),|| true) ; \
+                 fi
 else
 quiet_cmd_sign :=
       cmd_sign := :
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.modpost
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.modpost
@@ -87,8 +87,7 @@
 src := $(obj)
 
 # Include the module's Makefile to find KBUILD_EXTRA_SYMBOLS
-include $(if $(wildcard $(KBUILD_EXTMOD)/Kbuild), \
-             $(KBUILD_EXTMOD)/Kbuild, $(KBUILD_EXTMOD)/Makefile)
+include $(if $(wildcard $(src)/Kbuild), $(src)/Kbuild, $(src)/Makefile)
 
 # modpost option for external modules
 MODPOST += -e
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/Makefile.ubsan
+++ linux-xilinx-zynqmp-5.15.0/scripts/Makefile.ubsan
@@ -8,7 +8,6 @@
 ubsan-cflags-$(CONFIG_UBSAN_SHIFT)		+= -fsanitize=shift
 ubsan-cflags-$(CONFIG_UBSAN_DIV_ZERO)		+= -fsanitize=integer-divide-by-zero
 ubsan-cflags-$(CONFIG_UBSAN_UNREACHABLE)	+= -fsanitize=unreachable
-ubsan-cflags-$(CONFIG_UBSAN_OBJECT_SIZE)	+= -fsanitize=object-size
 ubsan-cflags-$(CONFIG_UBSAN_BOOL)		+= -fsanitize=bool
 ubsan-cflags-$(CONFIG_UBSAN_ENUM)		+= -fsanitize=enum
 ubsan-cflags-$(CONFIG_UBSAN_TRAP)		+= -fsanitize-undefined-trap-on-error
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/asn1_compiler.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/asn1_compiler.c
@@ -625,7 +625,7 @@
 	p = strrchr(argv[1], '/');
 	p = p ? p + 1 : argv[1];
 	grammar_name = strdup(p);
-	if (!p) {
+	if (!grammar_name) {
 		perror(NULL);
 		exit(1);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/atomic/fallbacks/read_acquire
+++ linux-xilinx-zynqmp-5.15.0/scripts/atomic/fallbacks/read_acquire
@@ -2,6 +2,15 @@
 static __always_inline ${ret}
 arch_${atomic}_read_acquire(const ${atomic}_t *v)
 {
-	return smp_load_acquire(&(v)->counter);
+	${int} ret;
+
+	if (__native_word(${atomic}_t)) {
+		ret = smp_load_acquire(&(v)->counter);
+	} else {
+		ret = arch_${atomic}_read(v);
+		__atomic_acquire_fence();
+	}
+
+	return ret;
 }
 EOF
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/atomic/fallbacks/set_release
+++ linux-xilinx-zynqmp-5.15.0/scripts/atomic/fallbacks/set_release
@@ -2,6 +2,11 @@
 static __always_inline void
 arch_${atomic}_set_release(${atomic}_t *v, ${int} i)
 {
-	smp_store_release(&(v)->counter, i);
+	if (__native_word(${atomic}_t)) {
+		smp_store_release(&(v)->counter, i);
+	} else {
+		__atomic_release_fence();
+		arch_${atomic}_set(v, i);
+	}
 }
 EOF
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/bpf_doc.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/bpf_doc.py
@@ -369,7 +369,7 @@
 instructions to the kernel when the programs are loaded. The format for that
 string is identical to the one in use for kernel modules (Dual licenses, such
 as "Dual BSD/GPL", may be used). Some helper functions are only accessible to
-programs that are compatible with the GNU Privacy License (GPL).
+programs that are compatible with the GNU General Public License (GNU GPL).
 
 In order to use such helpers, the eBPF program must be loaded with the correct
 license string passed (via **attr**) to the **bpf**\ () system call, and this
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/checkkconfigsymbols.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/checkkconfigsymbols.py
@@ -115,7 +115,7 @@
     return args
 
 
-def main():
+def print_undefined_symbols():
     """Main function of this module."""
     args = parse_options()
 
@@ -467,5 +467,16 @@
     return defined, references
 
 
+def main():
+    try:
+        print_undefined_symbols()
+    except BrokenPipeError:
+        # Python flushes standard streams on exit; redirect remaining output
+        # to devnull to avoid another BrokenPipeError at shutdown
+        devnull = os.open(os.devnull, os.O_WRONLY)
+        os.dup2(devnull, sys.stdout.fileno())
+        sys.exit(1)  # Python exits with error code 1 on EPIPE
+
+
 if __name__ == "__main__":
     main()
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/checkpatch.pl
+++ linux-xilinx-zynqmp-5.15.0/scripts/checkpatch.pl
@@ -489,7 +489,8 @@
 			____cacheline_aligned|
 			____cacheline_aligned_in_smp|
 			____cacheline_internodealigned_in_smp|
-			__weak
+			__weak|
+			__alloc_size\s*\(\s*\d+\s*(?:,\s*\d+\s*)?\)
 		  }x;
 our $Modifier;
 our $Inline	= qr{inline|__always_inline|noinline|__inline|__inline__};
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/checkstack.pl
+++ linux-xilinx-zynqmp-5.15.0/scripts/checkstack.pl
@@ -142,15 +142,11 @@
 while (my $line = <STDIN>) {
 	if ($line =~ m/$funcre/) {
 		$func = $1;
-		next if $line !~ m/^($xs*)/;
+		next if $line !~ m/^($x*)/;
 		if ($total_size > $min_stack) {
 			push @stack, "$intro$total_size\n";
 		}
-
-		$addr = $1;
-		$addr =~ s/ /0/g;
-		$addr = "0x$addr";
-
+		$addr = "0x$1";
 		$intro = "$addr $func [$file]:";
 		my $padlen = 56 - length($intro);
 		while ($padlen > 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/clang-tools/gen_compile_commands.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/clang-tools/gen_compile_commands.py
@@ -184,7 +184,7 @@
     # escape the pound sign '#', either as '\#' or '$(pound)' (depending on the
     # kernel version). The compile_commands.json file is not interepreted
     # by Make, so this code replaces the escaped version with '#'.
-    prefix = command_prefix.replace('\#', '#').replace('$(pound)', '#')
+    prefix = command_prefix.replace(r'\#', '#').replace('$(pound)', '#')
 
     # Use os.path.abspath() to normalize the path resolving '.' and '..' .
     abs_path = os.path.abspath(os.path.join(root_directory, file_path))
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/clang-tools/run-clang-tools.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/clang-tools/run-clang-tools.py
@@ -60,14 +60,21 @@
 
 
 def main():
-    args = parse_arguments()
+    try:
+        args = parse_arguments()
 
-    lock = multiprocessing.Lock()
-    pool = multiprocessing.Pool(initializer=init, initargs=(lock, args))
-    # Read JSON data into the datastore variable
-    with open(args.path, "r") as f:
-        datastore = json.load(f)
-        pool.map(run_analysis, datastore)
+        lock = multiprocessing.Lock()
+        pool = multiprocessing.Pool(initializer=init, initargs=(lock, args))
+        # Read JSON data into the datastore variable
+        with open(args.path, "r") as f:
+            datastore = json.load(f)
+            pool.map(run_analysis, datastore)
+    except BrokenPipeError:
+        # Python flushes standard streams on exit; redirect remaining output
+        # to devnull to avoid another BrokenPipeError at shutdown
+        devnull = os.open(os.devnull, os.O_WRONLY)
+        os.dup2(devnull, sys.stdout.fileno())
+        sys.exit(1)  # Python exits with error code 1 on EPIPE
 
 
 if __name__ == "__main__":
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/decode_stacktrace.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/decode_stacktrace.sh
@@ -8,6 +8,29 @@
 	echo "	$0 -r <release> | <vmlinux> [<base path>|auto] [<modules path>]"
 }
 
+# Try to find a Rust demangler
+if type llvm-cxxfilt >/dev/null 2>&1 ; then
+	cppfilt=llvm-cxxfilt
+elif type c++filt >/dev/null 2>&1 ; then
+	cppfilt=c++filt
+	cppfilt_opts=-i
+fi
+
+UTIL_SUFFIX=
+if [[ -z ${LLVM:-} ]]; then
+	UTIL_PREFIX=${CROSS_COMPILE:-}
+else
+	UTIL_PREFIX=llvm-
+	if [[ ${LLVM} == */ ]]; then
+		UTIL_PREFIX=${LLVM}${UTIL_PREFIX}
+	elif [[ ${LLVM} == -* ]]; then
+		UTIL_SUFFIX=${LLVM}
+	fi
+fi
+
+READELF=${UTIL_PREFIX}readelf${UTIL_SUFFIX}
+ADDR2LINE=${UTIL_PREFIX}addr2line${UTIL_SUFFIX}
+
 if [[ $1 == "-r" ]] ; then
 	vmlinux=""
 	basepath="auto"
@@ -45,8 +68,13 @@
 	fi
 fi
 
-declare -A cache
-declare -A modcache
+declare aarray_support=true
+declare -A cache 2>/dev/null
+if [[ $? != 0 ]]; then
+	aarray_support=false
+else
+	declare -A modcache
+fi
 
 find_module() {
 	if [[ -n $debuginfod ]] ; then
@@ -62,7 +90,7 @@
 
 	if [[ "$modpath" != "" ]] ; then
 		for fn in $(find "$modpath" -name "${module//_/[-_]}.ko*") ; do
-			if readelf -WS "$fn" | grep -qwF .debug_line ; then
+			if ${READELF} -WS "$fn" | grep -qwF .debug_line ; then
 				echo $fn
 				return
 			fi
@@ -97,7 +125,7 @@
 
 	if [[ $module == "" ]] ; then
 		local objfile=$vmlinux
-	elif [[ "${modcache[$module]+isset}" == "isset" ]]; then
+	elif [[ $aarray_support == true && "${modcache[$module]+isset}" == "isset" ]]; then
 		local objfile=${modcache[$module]}
 	else
 		local objfile=$(find_module)
@@ -105,7 +133,9 @@
 			echo "WARNING! Modules path isn't set, but is needed to parse this symbol" >&2
 			return
 		fi
-		modcache[$module]=$objfile
+		if [[ $aarray_support == true ]]; then
+			modcache[$module]=$objfile
+		fi
 	fi
 
 	# Remove the englobing parenthesis
@@ -125,7 +155,7 @@
 	# Use 'nm vmlinux' to figure out the base address of said symbol.
 	# It's actually faster to call it every time than to load it
 	# all into bash.
-	if [[ "${cache[$module,$name]+isset}" == "isset" ]]; then
+	if [[ $aarray_support == true && "${cache[$module,$name]+isset}" == "isset" ]]; then
 		local base_addr=${cache[$module,$name]}
 	else
 		local base_addr=$(nm "$objfile" 2>/dev/null | awk '$3 == "'$name'" && ($2 == "t" || $2 == "T") {print $1; exit}')
@@ -133,7 +163,9 @@
 			# address not found
 			return
 		fi
-		cache[$module,$name]="$base_addr"
+		if [[ $aarray_support == true ]]; then
+			cache[$module,$name]="$base_addr"
+		fi
 	fi
 	# Let's start doing the math to get the exact address into the
 	# symbol. First, strip out the symbol total length.
@@ -149,11 +181,13 @@
 
 	# Pass it to addr2line to get filename and line number
 	# Could get more than one result
-	if [[ "${cache[$module,$address]+isset}" == "isset" ]]; then
+	if [[ $aarray_support == true && "${cache[$module,$address]+isset}" == "isset" ]]; then
 		local code=${cache[$module,$address]}
 	else
-		local code=$(${CROSS_COMPILE}addr2line -i -e "$objfile" "$address" 2>/dev/null)
-		cache[$module,$address]=$code
+		local code=$(${ADDR2LINE} -i -e "$objfile" "$address" 2>/dev/null)
+		if [[ $aarray_support == true ]]; then
+			cache[$module,$address]=$code
+		fi
 	fi
 
 	# addr2line doesn't return a proper error code if it fails, so
@@ -169,6 +203,12 @@
 	# In the case of inlines, move everything to same line
 	code=${code//$'\n'/' '}
 
+	# Demangle if the name looks like a Rust symbol and if
+	# we got a Rust demangler
+	if [[ $name =~ ^_R && $cppfilt != "" ]] ; then
+		name=$("$cppfilt" "$cppfilt_opts" "$name")
+	fi
+
 	# Replace old address with pretty line numbers
 	symbol="$segment$name ($code)"
 }
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/diffconfig
+++ linux-xilinx-zynqmp-5.15.0/scripts/diffconfig
@@ -65,7 +65,7 @@
         else:
             print(" %s %s -> %s" % (config, value, new_value))
 
-def main():
+def show_diff():
     global merge_style
 
     # parse command line args
@@ -129,4 +129,16 @@
     for config in new:
         print_config("+", config, None, b[config])
 
-main()
+def main():
+    try:
+        show_diff()
+    except BrokenPipeError:
+        # Python flushes standard streams on exit; redirect remaining output
+        # to devnull to avoid another BrokenPipeError at shutdown
+        devnull = os.open(os.devnull, os.O_WRONLY)
+        os.dup2(devnull, sys.stdout.fileno())
+        sys.exit(1)  # Python exits with error code 1 on EPIPE
+
+
+if __name__ == '__main__':
+    main()
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/dtc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/scripts/dtc/Makefile
@@ -18,7 +18,7 @@
 # Source files need to get at the userspace version of libfdt_env.h to compile
 HOST_EXTRACFLAGS += -I $(srctree)/$(src)/libfdt
 
-ifeq ($(shell pkg-config --exists yaml-0.1 2>/dev/null && echo yes),)
+ifeq ($(shell $(HOSTPKG_CONFIG) --exists yaml-0.1 2>/dev/null && echo yes),)
 ifneq ($(CHECK_DT_BINDING)$(CHECK_DTBS),)
 $(error dtc needs libyaml for DT schema validation support. \
 	Install the necessary libyaml development package.)
@@ -27,9 +27,9 @@
 else
 dtc-objs	+= yamltree.o
 # To include <yaml.h> installed in a non-default path
-HOSTCFLAGS_yamltree.o := $(shell pkg-config --cflags yaml-0.1)
+HOSTCFLAGS_yamltree.o := $(shell $(HOSTPKG_CONFIG) --cflags yaml-0.1)
 # To link libyaml installed in a non-default path
-HOSTLDLIBS_dtc	:= $(shell pkg-config yaml-0.1 --libs)
+HOSTLDLIBS_dtc	:= $(shell $(HOSTPKG_CONFIG) --libs yaml-0.1)
 endif
 
 # Generated files need one more search path to include headers in source tree
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/dtc/dtx_diff
+++ linux-xilinx-zynqmp-5.15.0/scripts/dtc/dtx_diff
@@ -59,12 +59,8 @@
    or '/include/' to be processed.
 
    If DTx_1 and DTx_2 are in different architectures, then this script
-   may not work since \${ARCH} is part of the include path.  Two possible
-   workarounds:
-
-      `basename $0` \\
-          <(ARCH=arch_of_dtx_1 `basename $0` DTx_1) \\
-          <(ARCH=arch_of_dtx_2 `basename $0` DTx_2)
+   may not work since \${ARCH} is part of the include path.  The following
+   workaround can be used:
 
       `basename $0` ARCH=arch_of_dtx_1 DTx_1 >tmp_dtx_1.dts
       `basename $0` ARCH=arch_of_dtx_2 DTx_2 >tmp_dtx_2.dts
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/dummy-tools/gcc
+++ linux-xilinx-zynqmp-5.15.0/scripts/dummy-tools/gcc
@@ -96,12 +96,8 @@
 
 # To set GCC_PLUGINS
 if arg_contain -print-file-name=plugin "$@"; then
-	plugin_dir=$(mktemp -d)
-
-	mkdir -p $plugin_dir/include
-	touch $plugin_dir/include/plugin-version.h
-
-	echo $plugin_dir
+	# Use $0 to find the in-tree dummy directory
+	echo "$(dirname "$(readlink -f "$0")")/dummy-plugin-dir"
 	exit 0
 fi
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/extract-cert.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/extract-cert.c
@@ -23,6 +23,13 @@
 #include <openssl/err.h>
 #include <openssl/engine.h>
 
+/*
+ * OpenSSL 3.0 deprecates the OpenSSL's ENGINE API.
+ *
+ * Remove this if/when that API is no longer used
+ */
+#pragma GCC diagnostic ignored "-Wdeprecated-declarations"
+
 #define PKEY_ID_PKCS7 2
 
 static __attribute__((noreturn))
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/faddr2line
+++ linux-xilinx-zynqmp-5.15.0/scripts/faddr2line
@@ -44,17 +44,6 @@
 set -o errexit
 set -o nounset
 
-READELF="${CROSS_COMPILE:-}readelf"
-ADDR2LINE="${CROSS_COMPILE:-}addr2line"
-SIZE="${CROSS_COMPILE:-}size"
-NM="${CROSS_COMPILE:-}nm"
-
-command -v awk >/dev/null 2>&1 || die "awk isn't installed"
-command -v ${READELF} >/dev/null 2>&1 || die "readelf isn't installed"
-command -v ${ADDR2LINE} >/dev/null 2>&1 || die "addr2line isn't installed"
-command -v ${SIZE} >/dev/null 2>&1 || die "size isn't installed"
-command -v ${NM} >/dev/null 2>&1 || die "nm isn't installed"
-
 usage() {
 	echo "usage: faddr2line [--list] <object file> <func+offset> <func+offset>..." >&2
 	exit 1
@@ -69,6 +58,14 @@
 	exit 1
 }
 
+READELF="${CROSS_COMPILE:-}readelf"
+ADDR2LINE="${CROSS_COMPILE:-}addr2line"
+AWK="awk"
+
+command -v ${AWK} >/dev/null 2>&1 || die "${AWK} isn't installed"
+command -v ${READELF} >/dev/null 2>&1 || die "${READELF} isn't installed"
+command -v ${ADDR2LINE} >/dev/null 2>&1 || die "${ADDR2LINE} isn't installed"
+
 # Try to figure out the source directory prefix so we can remove it from the
 # addr2line output.  HACK ALERT: This assumes that start_kernel() is in
 # init/main.c!  This only works for vmlinux.  Otherwise it falls back to
@@ -76,7 +73,8 @@
 find_dir_prefix() {
 	local objfile=$1
 
-	local start_kernel_addr=$(${READELF} -sW $objfile | awk '$8 == "start_kernel" {printf "0x%s", $2}')
+	local start_kernel_addr=$(${READELF} --symbols --wide $objfile | sed 's/\[.*\]//' |
+		${AWK} '$8 == "start_kernel" {printf "0x%s", $2}')
 	[[ -z $start_kernel_addr ]] && return
 
 	local file_line=$(${ADDR2LINE} -e $objfile $start_kernel_addr)
@@ -97,86 +95,158 @@
 	local dir_prefix=$3
 	local print_warnings=$4
 
-	local func=${func_addr%+*}
-	local offset=${func_addr#*+}
-	offset=${offset%/*}
-	local size=
-	[[ $func_addr =~ "/" ]] && size=${func_addr#*/}
+	local sym_name=${func_addr%+*}
+	local func_offset=${func_addr#*+}
+	func_offset=${func_offset%/*}
+	local user_size=
+	local file_type
+	local is_vmlinux=0
+	[[ $func_addr =~ "/" ]] && user_size=${func_addr#*/}
 
-	if [[ -z $func ]] || [[ -z $offset ]] || [[ $func = $func_addr ]]; then
+	if [[ -z $sym_name ]] || [[ -z $func_offset ]] || [[ $sym_name = $func_addr ]]; then
 		warn "bad func+offset $func_addr"
 		DONE=1
 		return
 	fi
 
+	# vmlinux uses absolute addresses in the section table rather than
+	# section offsets.
+	local file_type=$(${READELF} --file-header $objfile |
+		${AWK} '$1 == "Type:" { print $2; exit }')
+	if [[ $file_type = "EXEC" ]] || [[ $file_type == "DYN" ]]; then
+		is_vmlinux=1
+	fi
+
 	# Go through each of the object's symbols which match the func name.
-	# In rare cases there might be duplicates.
-	file_end=$(${SIZE} -Ax $objfile | awk '$1 == ".text" {print $2}')
-	while read symbol; do
-		local fields=($symbol)
-		local sym_base=0x${fields[0]}
-		local sym_type=${fields[1]}
-		local sym_end=${fields[3]}
+	# In rare cases there might be duplicates, in which case we print all
+	# matches.
+	while read line; do
+		local fields=($line)
+		local sym_addr=0x${fields[1]}
+		local sym_elf_size=${fields[2]}
+		local sym_sec=${fields[6]}
+		local sec_size
+		local sec_name
+
+		# Get the section size:
+		sec_size=$(${READELF} --section-headers --wide $objfile |
+			sed 's/\[ /\[/' |
+			${AWK} -v sec=$sym_sec '$1 == "[" sec "]" { print "0x" $6; exit }')
+
+		if [[ -z $sec_size ]]; then
+			warn "bad section size: section: $sym_sec"
+			DONE=1
+			return
+		fi
+
+		# Get the section name:
+		sec_name=$(${READELF} --section-headers --wide $objfile |
+			sed 's/\[ /\[/' |
+			${AWK} -v sec=$sym_sec '$1 == "[" sec "]" { print $2; exit }')
+
+		if [[ -z $sec_name ]]; then
+			warn "bad section name: section: $sym_sec"
+			DONE=1
+			return
+		fi
+
+		# Calculate the symbol size.
+		#
+		# Unfortunately we can't use the ELF size, because kallsyms
+		# also includes the padding bytes in its size calculation.  For
+		# kallsyms, the size calculation is the distance between the
+		# symbol and the next symbol in a sorted list.
+		local sym_size
+		local cur_sym_addr
+		local found=0
+		while read line; do
+			local fields=($line)
+			cur_sym_addr=0x${fields[1]}
+			local cur_sym_elf_size=${fields[2]}
+			local cur_sym_name=${fields[7]:-}
+
+			if [[ $cur_sym_addr = $sym_addr ]] &&
+			   [[ $cur_sym_elf_size = $sym_elf_size ]] &&
+			   [[ $cur_sym_name = $sym_name ]]; then
+				found=1
+				continue
+			fi
+
+			if [[ $found = 1 ]]; then
+				sym_size=$(($cur_sym_addr - $sym_addr))
+				[[ $sym_size -lt $sym_elf_size ]] && continue;
+				found=2
+				break
+			fi
+		done < <(${READELF} --symbols --wide $objfile | sed 's/\[.*\]//' | ${AWK} -v sec=$sym_sec '$7 == sec' | sort --key=2)
+
+		if [[ $found = 0 ]]; then
+			warn "can't find symbol: sym_name: $sym_name sym_sec: $sym_sec sym_addr: $sym_addr sym_elf_size: $sym_elf_size"
+			DONE=1
+			return
+		fi
+
+		# If nothing was found after the symbol, assume it's the last
+		# symbol in the section.
+		[[ $found = 1 ]] && sym_size=$(($sec_size - $sym_addr))
 
-		# calculate the size
-		local sym_size=$(($sym_end - $sym_base))
 		if [[ -z $sym_size ]] || [[ $sym_size -le 0 ]]; then
-			warn "bad symbol size: base: $sym_base end: $sym_end"
+			warn "bad symbol size: sym_addr: $sym_addr cur_sym_addr: $cur_sym_addr"
 			DONE=1
 			return
 		fi
+
 		sym_size=0x$(printf %x $sym_size)
 
-		# calculate the address
-		local addr=$(($sym_base + $offset))
+		# Calculate the address from user-supplied offset:
+		local addr=$(($sym_addr + $func_offset))
 		if [[ -z $addr ]] || [[ $addr = 0 ]]; then
-			warn "bad address: $sym_base + $offset"
+			warn "bad address: $sym_addr + $func_offset"
 			DONE=1
 			return
 		fi
 		addr=0x$(printf %x $addr)
 
-		# weed out non-function symbols
-		if [[ $sym_type != t ]] && [[ $sym_type != T ]]; then
-			[[ $print_warnings = 1 ]] &&
-				echo "skipping $func address at $addr due to non-function symbol of type '$sym_type'"
-			continue
-		fi
-
-		# if the user provided a size, make sure it matches the symbol's size
-		if [[ -n $size ]] && [[ $size -ne $sym_size ]]; then
+		# If the user provided a size, make sure it matches the symbol's size:
+		if [[ -n $user_size ]] && [[ $user_size -ne $sym_size ]]; then
 			[[ $print_warnings = 1 ]] &&
-				echo "skipping $func address at $addr due to size mismatch ($size != $sym_size)"
+				echo "skipping $sym_name address at $addr due to size mismatch ($user_size != $sym_size)"
 			continue;
 		fi
 
-		# make sure the provided offset is within the symbol's range
-		if [[ $offset -gt $sym_size ]]; then
+		# Make sure the provided offset is within the symbol's range:
+		if [[ $func_offset -gt $sym_size ]]; then
 			[[ $print_warnings = 1 ]] &&
-				echo "skipping $func address at $addr due to size mismatch ($offset > $sym_size)"
+				echo "skipping $sym_name address at $addr due to size mismatch ($func_offset > $sym_size)"
 			continue
 		fi
 
-		# separate multiple entries with a blank line
+		# In case of duplicates or multiple addresses specified on the
+		# cmdline, separate multiple entries with a blank line:
 		[[ $FIRST = 0 ]] && echo
 		FIRST=0
 
-		# pass real address to addr2line
-		echo "$func+$offset/$sym_size:"
-		local file_lines=$(${ADDR2LINE} -fpie $objfile $addr | sed "s; $dir_prefix\(\./\)*; ;")
-		[[ -z $file_lines ]] && return
+		echo "$sym_name+$func_offset/$sym_size:"
+
+		# Pass section address to addr2line and strip absolute paths
+		# from the output:
+		local args="--functions --pretty-print --inlines --exe=$objfile"
+		[[ $is_vmlinux = 0 ]] && args="$args --section=$sec_name"
+		local output=$(${ADDR2LINE} $args $addr | sed "s; $dir_prefix\(\./\)*; ;")
+		[[ -z $output ]] && continue
 
+		# Default output (non --list):
 		if [[ $LIST = 0 ]]; then
-			echo "$file_lines" | while read -r line
+			echo "$output" | while read -r line
 			do
 				echo $line
 			done
 			DONE=1;
-			return
+			continue
 		fi
 
-		# show each line with context
-		echo "$file_lines" | while read -r line
+		# For --list, show each line with its corresponding source code:
+		echo "$output" | while read -r line
 		do
 			echo
 			echo $line
@@ -184,12 +254,12 @@
 			n1=$[$n-5]
 			n2=$[$n+5]
 			f=$(echo $line | sed 's/.*at \(.\+\):.*/\1/g')
-			awk 'NR>=strtonum("'$n1'") && NR<=strtonum("'$n2'") { if (NR=='$n') printf(">%d<", NR); else printf(" %d ", NR); printf("\t%s\n", $0)}' $f
+			${AWK} 'NR>=strtonum("'$n1'") && NR<=strtonum("'$n2'") { if (NR=='$n') printf(">%d<", NR); else printf(" %d ", NR); printf("\t%s\n", $0)}' $f
 		done
 
 		DONE=1
 
-	done < <(${NM} -n $objfile | awk -v fn=$func -v end=$file_end '$3 == fn { found=1; line=$0; start=$1; next } found == 1 { found=0; print line, "0x"$1 } END {if (found == 1) print line, end; }')
+	done < <(${READELF} --symbols --wide $objfile | sed 's/\[.*\]//' | ${AWK} -v fn=$sym_name '$4 == "FUNC" && $8 == fn')
 }
 
 [[ $# -lt 2 ]] && usage
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gcc-plugins/gcc-common.h
+++ linux-xilinx-zynqmp-5.15.0/scripts/gcc-plugins/gcc-common.h
@@ -77,7 +77,9 @@
 #include "varasm.h"
 #include "stor-layout.h"
 #include "internal-fn.h"
+#include "gimple.h"
 #include "gimple-expr.h"
+#include "gimple-iterator.h"
 #include "gimple-fold.h"
 #include "context.h"
 #include "tree-ssa-alias.h"
@@ -91,11 +93,9 @@
 #include "tree-eh.h"
 #include "stmt.h"
 #include "gimplify.h"
-#include "gimple.h"
 #include "tree-ssa-operands.h"
 #include "tree-phinodes.h"
 #include "tree-cfg.h"
-#include "gimple-iterator.h"
 #include "gimple-ssa.h"
 #include "ssa-iterators.h"
 
@@ -570,4 +570,8 @@
 #define SET_DECL_MODE(decl, mode)	DECL_MODE(decl) = (mode)
 #endif
 
+#if BUILDING_GCC_VERSION >= 14000
+#define last_stmt(x)			last_nondebug_stmt(x)
+#endif
+
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gcc-plugins/latent_entropy_plugin.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/gcc-plugins/latent_entropy_plugin.c
@@ -86,25 +86,31 @@
 	.help		= "disable\tturn off latent entropy instrumentation\n",
 };
 
-static unsigned HOST_WIDE_INT seed;
-/*
- * get_random_seed() (this is a GCC function) generates the seed.
- * This is a simple random generator without any cryptographic security because
- * the entropy doesn't come from here.
- */
+static unsigned HOST_WIDE_INT deterministic_seed;
+static unsigned HOST_WIDE_INT rnd_buf[32];
+static size_t rnd_idx = ARRAY_SIZE(rnd_buf);
+static int urandom_fd = -1;
+
 static unsigned HOST_WIDE_INT get_random_const(void)
 {
-	unsigned int i;
-	unsigned HOST_WIDE_INT ret = 0;
-
-	for (i = 0; i < 8 * sizeof(ret); i++) {
-		ret = (ret << 1) | (seed & 1);
-		seed >>= 1;
-		if (ret & 1)
-			seed ^= 0xD800000000000000ULL;
+	if (deterministic_seed) {
+		unsigned HOST_WIDE_INT w = deterministic_seed;
+		w ^= w << 13;
+		w ^= w >> 7;
+		w ^= w << 17;
+		deterministic_seed = w;
+		return deterministic_seed;
 	}
 
-	return ret;
+	if (urandom_fd < 0) {
+		urandom_fd = open("/dev/urandom", O_RDONLY);
+		gcc_assert(urandom_fd >= 0);
+	}
+	if (rnd_idx >= ARRAY_SIZE(rnd_buf)) {
+		gcc_assert(read(urandom_fd, rnd_buf, sizeof(rnd_buf)) == sizeof(rnd_buf));
+		rnd_idx = 0;
+	}
+	return rnd_buf[rnd_idx++];
 }
 
 static tree tree_get_random_const(tree type)
@@ -537,8 +543,6 @@
 	tree type, id;
 	int quals;
 
-	seed = get_random_seed(false);
-
 	if (in_lto_p)
 		return;
 
@@ -573,6 +577,12 @@
 	const struct plugin_argument * const argv = plugin_info->argv;
 	int i;
 
+	/*
+	 * Call get_random_seed() with noinit=true, so that this returns
+	 * 0 in the case where no seed has been passed via -frandom-seed.
+	 */
+	deterministic_seed = get_random_seed(true);
+
 	static const struct ggc_root_tab gt_ggc_r_gt_latent_entropy[] = {
 		{
 			.base = &latent_entropy_decl,
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gcc-plugins/randomize_layout_plugin.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/gcc-plugins/randomize_layout_plugin.c
@@ -209,12 +209,14 @@
 
 static void performance_shuffle(tree *newtree, unsigned long length, ranctx *prng_state)
 {
-	unsigned long i, x;
+	unsigned long i, x, index;
 	struct partition_group size_group[length];
 	unsigned long num_groups = 0;
 	unsigned long randnum;
 
 	partition_struct(newtree, length, (struct partition_group *)&size_group, &num_groups);
+
+	/* FIXME: this group shuffle is currently a no-op. */
 	for (i = num_groups - 1; i > 0; i--) {
 		struct partition_group tmp;
 		randnum = ranval(prng_state) % (i + 1);
@@ -224,11 +226,14 @@
 	}
 
 	for (x = 0; x < num_groups; x++) {
-		for (i = size_group[x].start + size_group[x].length - 1; i > size_group[x].start; i--) {
+		for (index = size_group[x].length - 1; index > 0; index--) {
 			tree tmp;
+
+			i = size_group[x].start + index;
 			if (DECL_BIT_FIELD_TYPE(newtree[i]))
 				continue;
-			randnum = ranval(prng_state) % (i + 1);
+			randnum = ranval(prng_state) % (index + 1);
+			randnum += size_group[x].start;
 			// we could handle this case differently if desired
 			if (DECL_BIT_FIELD_TYPE(newtree[randnum]))
 				continue;
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gcc-plugins/stackleak_plugin.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/gcc-plugins/stackleak_plugin.c
@@ -429,6 +429,23 @@
 	return 0;
 }
 
+/*
+ * STRING_CST may or may not be NUL terminated:
+ * https://gcc.gnu.org/onlinedocs/gccint/Constant-expressions.html
+ */
+static inline bool string_equal(tree node, const char *string, int length)
+{
+	if (TREE_STRING_LENGTH(node) < length)
+		return false;
+	if (TREE_STRING_LENGTH(node) > length + 1)
+		return false;
+	if (TREE_STRING_LENGTH(node) == length + 1 &&
+	    TREE_STRING_POINTER(node)[length] != '\0')
+		return false;
+	return !memcmp(TREE_STRING_POINTER(node), string, length);
+}
+#define STRING_EQUAL(node, str)	string_equal(node, str, strlen(str))
+
 static bool stackleak_gate(void)
 {
 	tree section;
@@ -438,13 +455,19 @@
 	if (section && TREE_VALUE(section)) {
 		section = TREE_VALUE(TREE_VALUE(section));
 
-		if (!strncmp(TREE_STRING_POINTER(section), ".init.text", 10))
+		if (STRING_EQUAL(section, ".init.text"))
+			return false;
+		if (STRING_EQUAL(section, ".devinit.text"))
+			return false;
+		if (STRING_EQUAL(section, ".cpuinit.text"))
+			return false;
+		if (STRING_EQUAL(section, ".meminit.text"))
 			return false;
-		if (!strncmp(TREE_STRING_POINTER(section), ".devinit.text", 13))
+		if (STRING_EQUAL(section, ".noinstr.text"))
 			return false;
-		if (!strncmp(TREE_STRING_POINTER(section), ".cpuinit.text", 13))
+		if (STRING_EQUAL(section, ".entry.text"))
 			return false;
-		if (!strncmp(TREE_STRING_POINTER(section), ".meminit.text", 13))
+		if (STRING_EQUAL(section, ".head.text"))
 			return false;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gcc-x86_32-has-stack-protector.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/gcc-x86_32-has-stack-protector.sh
@@ -5,4 +5,4 @@
 # -mstack-protector-guard-reg, added by
 # https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81708
 
-echo "int foo(void) { char X[200]; return 3; }" | $* -S -x c -c -m32 -O0 -fstack-protector -mstack-protector-guard-reg=fs -mstack-protector-guard-symbol=__stack_chk_guard - -o - 2> /dev/null | grep -q "%fs"
+echo "int foo(void) { char X[200]; return 3; }" | $* -S -x c -m32 -O0 -fstack-protector -mstack-protector-guard-reg=fs -mstack-protector-guard-symbol=__stack_chk_guard - -o - 2> /dev/null | grep -q "%fs"
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gcc-x86_64-has-stack-protector.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/gcc-x86_64-has-stack-protector.sh
@@ -1,4 +1,4 @@
 #!/bin/sh
 # SPDX-License-Identifier: GPL-2.0
 
-echo "int foo(void) { char X[200]; return 3; }" | $* -S -x c -c -m64 -O0 -mcmodel=kernel -fno-PIE -fstack-protector - -o - 2> /dev/null | grep -q "%gs"
+echo "int foo(void) { char X[200]; return 3; }" | $* -S -x c -m64 -O0 -mcmodel=kernel -fno-PIE -fstack-protector - -o - 2> /dev/null | grep -q "%gs"
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/clk.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/clk.py
@@ -41,6 +41,8 @@
             self.show_subtree(child, level + 1)
 
     def invoke(self, arg, from_tty):
+        if utils.gdb_eval_or_none("clk_root_list") is None:
+            raise gdb.GdbError("No clocks registered")
         gdb.write("                                 enable  prepare  protect               \n")
         gdb.write("   clock                          count    count    count        rate   \n")
         gdb.write("------------------------------------------------------------------------\n")
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/config.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/config.py
@@ -24,9 +24,9 @@
             filename = arg
 
         try:
-            py_config_ptr = gdb.parse_and_eval("kernel_config_data + 8")
-            py_config_size = gdb.parse_and_eval(
-                    "sizeof(kernel_config_data) - 1 - 8 * 2")
+            py_config_ptr = gdb.parse_and_eval("&kernel_config_data")
+            py_config_ptr_end = gdb.parse_and_eval("&kernel_config_data_end")
+            py_config_size = py_config_ptr_end - py_config_ptr
         except gdb.error as e:
             raise gdb.GdbError("Can't find config, enable CONFIG_IKCONFIG?")
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/constants.py.in
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/constants.py.in
@@ -39,17 +39,19 @@
 
 import gdb
 
+LX_CONFIG(CONFIG_DEBUG_INFO_REDUCED)
+
 /* linux/clk-provider.h */
 if IS_BUILTIN(CONFIG_COMMON_CLK):
     LX_GDBPARSED(CLK_GET_RATE_NOCACHE)
 
 /* linux/fs.h */
-LX_VALUE(SB_RDONLY)
-LX_VALUE(SB_SYNCHRONOUS)
-LX_VALUE(SB_MANDLOCK)
-LX_VALUE(SB_DIRSYNC)
-LX_VALUE(SB_NOATIME)
-LX_VALUE(SB_NODIRATIME)
+LX_GDBPARSED(SB_RDONLY)
+LX_GDBPARSED(SB_SYNCHRONOUS)
+LX_GDBPARSED(SB_MANDLOCK)
+LX_GDBPARSED(SB_DIRSYNC)
+LX_GDBPARSED(SB_NOATIME)
+LX_GDBPARSED(SB_NODIRATIME)
 
 /* linux/htimer.h */
 LX_GDBPARSED(hrtimer_resolution)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/dmesg.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/dmesg.py
@@ -22,7 +22,6 @@
 prb_desc_ring_type = utils.CachedType("struct prb_desc_ring")
 prb_data_ring_type = utils.CachedType("struct prb_data_ring")
 printk_ringbuffer_type = utils.CachedType("struct printk_ringbuffer")
-atomic_long_type = utils.CachedType("atomic_long_t")
 
 class LxDmesg(gdb.Command):
     """Print Linux kernel log buffer."""
@@ -44,19 +43,17 @@
         sz = prb_desc_ring_type.get_type().sizeof
         desc_ring = utils.read_memoryview(inf, addr, sz).tobytes()
 
-        # read in descriptor array
+        # read in descriptor count, size, and address
         off = prb_desc_ring_type.get_type()['count_bits'].bitpos // 8
         desc_ring_count = 1 << utils.read_u32(desc_ring, off)
         desc_sz = prb_desc_type.get_type().sizeof
         off = prb_desc_ring_type.get_type()['descs'].bitpos // 8
-        addr = utils.read_ulong(desc_ring, off)
-        descs = utils.read_memoryview(inf, addr, desc_sz * desc_ring_count).tobytes()
+        desc_addr = utils.read_ulong(desc_ring, off)
 
-        # read in info array
+        # read in info size and address
         info_sz = printk_info_type.get_type().sizeof
         off = prb_desc_ring_type.get_type()['infos'].bitpos // 8
-        addr = utils.read_ulong(desc_ring, off)
-        infos = utils.read_memoryview(inf, addr, info_sz * desc_ring_count).tobytes()
+        info_addr = utils.read_ulong(desc_ring, off)
 
         # read in text data ring structure
         off = printk_ringbuffer_type.get_type()['text_data_ring'].bitpos // 8
@@ -64,14 +61,11 @@
         sz = prb_data_ring_type.get_type().sizeof
         text_data_ring = utils.read_memoryview(inf, addr, sz).tobytes()
 
-        # read in text data
+        # read in text data size and address
         off = prb_data_ring_type.get_type()['size_bits'].bitpos // 8
         text_data_sz = 1 << utils.read_u32(text_data_ring, off)
         off = prb_data_ring_type.get_type()['data'].bitpos // 8
-        addr = utils.read_ulong(text_data_ring, off)
-        text_data = utils.read_memoryview(inf, addr, text_data_sz).tobytes()
-
-        counter_off = atomic_long_type.get_type()['counter'].bitpos // 8
+        text_data_addr = utils.read_ulong(text_data_ring, off)
 
         sv_off = prb_desc_type.get_type()['state_var'].bitpos // 8
 
@@ -92,9 +86,9 @@
 
         # read in tail and head descriptor ids
         off = prb_desc_ring_type.get_type()['tail_id'].bitpos // 8
-        tail_id = utils.read_u64(desc_ring, off + counter_off)
+        tail_id = utils.read_atomic_long(desc_ring, off)
         off = prb_desc_ring_type.get_type()['head_id'].bitpos // 8
-        head_id = utils.read_u64(desc_ring, off + counter_off)
+        head_id = utils.read_atomic_long(desc_ring, off)
 
         did = tail_id
         while True:
@@ -102,17 +96,20 @@
             desc_off = desc_sz * ind
             info_off = info_sz * ind
 
+            desc = utils.read_memoryview(inf, desc_addr + desc_off, desc_sz).tobytes()
+
             # skip non-committed record
-            state = 3 & (utils.read_u64(descs, desc_off + sv_off +
-                                        counter_off) >> desc_flags_shift)
+            state = 3 & (utils.read_atomic_long(desc, sv_off) >> desc_flags_shift)
             if state != desc_committed and state != desc_finalized:
                 if did == head_id:
                     break
                 did = (did + 1) & desc_id_mask
                 continue
 
-            begin = utils.read_ulong(descs, desc_off + begin_off) % text_data_sz
-            end = utils.read_ulong(descs, desc_off + next_off) % text_data_sz
+            begin = utils.read_ulong(desc, begin_off) % text_data_sz
+            end = utils.read_ulong(desc, next_off) % text_data_sz
+
+            info = utils.read_memoryview(inf, info_addr + info_off, info_sz).tobytes()
 
             # handle data-less record
             if begin & 1 == 1:
@@ -125,16 +122,17 @@
                 # skip over descriptor id
                 text_start = begin + utils.get_long_type().sizeof
 
-                text_len = utils.read_u16(infos, info_off + len_off)
+                text_len = utils.read_u16(info, len_off)
 
                 # handle truncated message
                 if end - text_start < text_len:
                     text_len = end - text_start
 
-                text = text_data[text_start:text_start + text_len].decode(
-                    encoding='utf8', errors='replace')
+                text_data = utils.read_memoryview(inf, text_data_addr + text_start,
+                                                  text_len).tobytes()
+                text = text_data[0:text_len].decode(encoding='utf8', errors='replace')
 
-            time_stamp = utils.read_u64(infos, info_off + ts_off)
+            time_stamp = utils.read_u64(info, ts_off)
 
             for line in text.splitlines():
                 msg = u"[{time:12.6f}] {line}\n".format(
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/genpd.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/genpd.py
@@ -5,7 +5,7 @@
 import gdb
 import sys
 
-from linux.utils import CachedType
+from linux.utils import CachedType, gdb_eval_or_none
 from linux.lists import list_for_each_entry
 
 generic_pm_domain_type = CachedType('struct generic_pm_domain')
@@ -70,6 +70,8 @@
             gdb.write('    %-50s  %s\n' % (kobj_path, rtpm_status_str(dev)))
 
     def invoke(self, arg, from_tty):
+        if gdb_eval_or_none("&gpd_list") is None:
+            raise gdb.GdbError("No power domain(s) registered")
         gdb.write('domain                          status          children\n');
         gdb.write('    /device                                             runtime status\n');
         gdb.write('----------------------------------------------------------------------\n');
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/timerlist.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/timerlist.py
@@ -73,7 +73,7 @@
     ts = cpus.per_cpu(tick_sched_ptr, cpu)
 
     text = "cpu: {}\n".format(cpu)
-    for i in xrange(max_clock_bases):
+    for i in range(max_clock_bases):
         text += " clock {}:\n".format(i)
         text += print_base(cpu_base['clock_base'][i])
 
@@ -158,6 +158,8 @@
     num_bytes = (nr_cpu_ids + 7) / 8
     buf = utils.read_memoryview(inf, bits, num_bytes).tobytes()
     buf = binascii.b2a_hex(buf)
+    if type(buf) is not str:
+        buf=buf.decode()
 
     chunks = []
     i = num_bytes
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/linux/utils.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/linux/utils.py
@@ -35,13 +35,12 @@
 
 
 long_type = CachedType("long")
-
+atomic_long_type = CachedType("atomic_long_t")
 
 def get_long_type():
     global long_type
     return long_type.get_type()
 
-
 def offset_of(typeobj, field):
     element = gdb.Value(0).cast(typeobj)
     return int(str(element[field].address).split()[0], 16)
@@ -89,7 +88,10 @@
 
 
 def read_memoryview(inf, start, length):
-    return memoryview(inf.read_memory(start, length))
+    m = inf.read_memory(start, length)
+    if type(m) is memoryview:
+        return m
+    return memoryview(m)
 
 
 def read_u16(buffer, offset):
@@ -129,6 +131,17 @@
     else:
         return read_u32(buffer, offset)
 
+atomic_long_counter_offset = atomic_long_type.get_type()['counter'].bitpos
+atomic_long_counter_sizeof = atomic_long_type.get_type()['counter'].type.sizeof
+
+def read_atomic_long(buffer, offset):
+    global atomic_long_counter_offset
+    global atomic_long_counter_sizeof
+
+    if atomic_long_counter_sizeof == 8:
+        return read_u64(buffer, offset + atomic_long_counter_offset)
+    else:
+        return read_u32(buffer, offset + atomic_long_counter_offset)
 
 target_arch = None
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/gdb/vmlinux-gdb.py
+++ linux-xilinx-zynqmp-5.15.0/scripts/gdb/vmlinux-gdb.py
@@ -22,6 +22,10 @@
     gdb.write("NOTE: gdb 7.2 or later required for Linux helper scripts to "
               "work.\n")
 else:
+    import linux.constants
+    if linux.constants.LX_CONFIG_DEBUG_INFO_REDUCED:
+        raise gdb.GdbError("Reduced debug information will prevent GDB "
+                           "from having complete types.\n")
     import linux.utils
     import linux.symbols
     import linux.modules
@@ -32,7 +36,6 @@
     import linux.lists
     import linux.rbtree
     import linux.proc
-    import linux.constants
     import linux.timerlist
     import linux.clk
     import linux.genpd
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/genksyms/genksyms.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/genksyms/genksyms.c
@@ -241,6 +241,7 @@
 						"unchanged\n");
 				}
 				sym->is_declared = 1;
+				free_list(defn, NULL);
 				return sym;
 			} else if (!sym->is_declared) {
 				if (sym->is_override && flag_preserve) {
@@ -249,6 +250,7 @@
 					print_type_name(type, name);
 					fprintf(stderr, " modversion change\n");
 					sym->is_declared = 1;
+					free_list(defn, NULL);
 					return sym;
 				} else {
 					status = is_unknown_symbol(sym) ?
@@ -256,6 +258,7 @@
 				}
 			} else {
 				error_with_pos("redefinition of %s", name);
+				free_list(defn, NULL);
 				return sym;
 			}
 			break;
@@ -271,11 +274,15 @@
 				break;
 			}
 		}
+
+		free_list(sym->defn, NULL);
+		free(sym->name);
+		free(sym);
 		--nsyms;
 	}
 
 	sym = xmalloc(sizeof(*sym));
-	sym->name = name;
+	sym->name = xstrdup(name);
 	sym->type = type;
 	sym->defn = defn;
 	sym->expansion_trail = NULL;
@@ -482,7 +489,7 @@
 			defn = def;
 			def = read_node(f);
 		}
-		subsym = add_reference_symbol(xstrdup(sym->string), sym->tag,
+		subsym = add_reference_symbol(sym->string, sym->tag,
 					      defn, is_extern);
 		subsym->is_override = is_override;
 		free_node(sym);
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/genksyms/genksyms.h
+++ linux-xilinx-zynqmp-5.15.0/scripts/genksyms/genksyms.h
@@ -32,7 +32,7 @@
 
 struct symbol {
 	struct symbol *hash_next;
-	const char *name;
+	char *name;
 	enum symbol_type type;
 	struct string_list *defn;
 	struct symbol *expansion_trail;
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/genksyms/parse.y
+++ linux-xilinx-zynqmp-5.15.0/scripts/genksyms/parse.y
@@ -152,14 +152,19 @@
 	;
 
 init_declarator_list_opt:
-	/* empty */				{ $$ = NULL; }
-	| init_declarator_list
+	/* empty */			{ $$ = NULL; }
+	| init_declarator_list		{ free_list(decl_spec, NULL); $$ = $1; }
 	;
 
 init_declarator_list:
 	init_declarator
 		{ struct string_list *decl = *$1;
 		  *$1 = NULL;
+
+		  /* avoid sharing among multiple init_declarators */
+		  if (decl_spec)
+		    decl_spec = copy_list_range(decl_spec, NULL);
+
 		  add_symbol(current_name,
 			     is_typedef ? SYM_TYPEDEF : SYM_NORMAL, decl, is_extern);
 		  current_name = NULL;
@@ -170,6 +175,11 @@
 		  *$3 = NULL;
 		  free_list(*$2, NULL);
 		  *$2 = decl_spec;
+
+		  /* avoid sharing among multiple init_declarators */
+		  if (decl_spec)
+		    decl_spec = copy_list_range(decl_spec, NULL);
+
 		  add_symbol(current_name,
 			     is_typedef ? SYM_TYPEDEF : SYM_NORMAL, decl, is_extern);
 		  current_name = NULL;
@@ -472,12 +482,12 @@
 enumerator:
 	IDENT
 		{
-			const char *name = strdup((*$1)->string);
+			const char *name = (*$1)->string;
 			add_symbol(name, SYM_ENUM_CONST, NULL, 0);
 		}
 	| IDENT '=' EXPRESSION_PHRASE
 		{
-			const char *name = strdup((*$1)->string);
+			const char *name = (*$1)->string;
 			struct string_list *expr = copy_list_range(*$3, *$2);
 			add_symbol(name, SYM_ENUM_CONST, expr, 0);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/get_abi.pl
+++ linux-xilinx-zynqmp-5.15.0/scripts/get_abi.pl
@@ -75,7 +75,7 @@
 	$name =~ s,.*/,,;
 
 	my $fn = $file;
-	$fn =~ s,Documentation/ABI/,,;
+	$fn =~ s,.*Documentation/ABI/,,;
 
 	my $nametag = "File $fn";
 	$data{$nametag}->{what} = "File $name";
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/insert-sys-cert.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/insert-sys-cert.c
@@ -7,7 +7,8 @@
  * This software may be used and distributed according to the terms
  * of the GNU General Public License, incorporated herein by reference.
  *
- * Usage: insert-sys-cert [-s <System.map> -b <vmlinux> -c <certfile>
+ * Usage: insert-sys-cert [-s <System.map>] -b <vmlinux> -c <certfile>
+ *                        [-s <System.map>] -z <bzImage> -c <certfile>
  */
 
 #define _GNU_SOURCE
@@ -257,6 +258,169 @@
 	return buf;
 }
 
+static void get_payload_info(char *bzimage, int *offset, int *size)
+{
+	unsigned int system_offset;
+	unsigned char setup_sectors;
+
+	setup_sectors = bzimage[0x1f1] + 1;
+	system_offset = setup_sectors * 512;
+	*offset = system_offset + *((int*)&bzimage[0x248]);
+	*size = *((int*)&bzimage[0x24c]);
+}
+
+static void update_payload_info(char* bzimage, int new_size)
+{
+	int offset, size;
+	get_payload_info(bzimage, &offset, &size);
+	*((int*)&bzimage[0x24c]) = new_size;
+	if (new_size < size)
+		memset(bzimage + offset + new_size, 0, size - new_size);
+}
+
+struct zipper {
+	unsigned char pattern[10];
+	int length;
+	char *command;
+	char *compress;
+};
+
+struct zipper zippers[] = {
+	{{0x7F,'E','L','F'}, 4, "cat", "cat"},
+	{{0x1F,0x8B}, 2, "gunzip", "gzip -n -f -9"},
+	{{0xFD,'7','z','X','Z',0}, 6, "unxz", "xz"},
+	{{'B','Z','h'},3, "bunzip2", "bzip2 -9"},
+	{{0xFF,'L','Z','M','A',0}, 6, "unlzma", "lzma -9"},
+	{{0xD3,'L','Z','O',0,'\r','\n',0x20,'\n'}, 9, "lzop -d", "lzop -9"}
+};
+
+static struct zipper* get_zipper(char *p) {
+	int i;
+	for (i = 0; i < sizeof(zippers)/sizeof(struct zipper); i++) {
+		if (memcmp(p, zippers[i].pattern, zippers[i].length) == 0)
+			return &zippers[i];
+	}
+	return NULL;
+}
+
+/*
+ * This only works for x86 bzImage
+ */
+static void extract_vmlinux(char *bzimage, int bzimage_size,
+			char **file, struct zipper **zipper)
+{
+	int r;
+	char src[15] = "vmlinux-XXXXXX";
+	char dest[15] = "vmlinux-XXXXXX";
+	char cmd[100];
+	int src_fd, dest_fd;
+	int offset, size;
+	struct zipper *z;
+
+	/* TODO: verify that bzImage is supported */
+
+	get_payload_info(bzimage, &offset, &size);
+	z = get_zipper(bzimage + offset);
+	if (z == NULL) {
+		err("Unable to determine the compression of vmlinux\n");
+		return;
+	}
+
+	src_fd = mkstemp(src);
+	if (src_fd == -1) {
+		perror("Could not create temp file");
+		return;
+	}
+
+	r = write(src_fd, bzimage + offset, size);
+	if (r != size) {
+		perror("Could not write vmlinux");
+		return;
+	}
+	dest_fd = mkstemp(dest);
+	if (dest_fd == -1) {
+		perror("Could not create temp file");
+		return;
+	}
+
+	snprintf(cmd, sizeof(cmd), "%s <%s >%s", z->command, src, dest);
+	info("Executing: %s\n", cmd);
+	r = system(cmd);
+	if (r!=0)
+		warn("Possible errors when extracting\n");
+
+	r = remove(src);
+	if (r!=0)
+		perror(src);
+
+	*file = strdup(dest);
+	*zipper = z;
+}
+
+static void repack_image(char *bzimage, int bzimage_size,
+			char* vmlinux_file, struct zipper *z)
+{
+	char tmp[15] = "vmlinux-XXXXXX";
+	char cmd[100];
+	int fd;
+	struct stat st;
+	int new_size;
+	int r;
+	int offset, size;
+
+	get_payload_info(bzimage, &offset, &size);
+
+	fd = mkstemp(tmp);
+	if (fd == -1) {
+		perror("Could not create temp file");
+		return;
+	}
+	snprintf(cmd, sizeof(cmd), "%s <%s >%s",
+			z->compress, vmlinux_file, tmp);
+
+	info("Executing: %s\n", cmd);
+	r = system(cmd);
+	if (r!=0)
+		warn("Possible errors when compressing\n");
+
+	r = remove(vmlinux_file);
+	if (r!=0)
+		perror(vmlinux_file);
+
+	if (fstat(fd, &st)) {
+		perror("Could not determine file size");
+		close(fd);
+
+	}
+	new_size = st.st_size;
+	if (new_size > size) {
+		err("Increase in compressed size is not supported.\n");
+		err("Old size was %d, new size is %d\n", size, new_size);
+		exit(EXIT_FAILURE);
+	}
+
+	r = read(fd, bzimage + offset, new_size);
+	if (r != new_size)
+		perror(tmp);
+
+	r = remove(tmp);
+	if (r!=0)
+		perror(tmp);
+
+	/* x86 specific patching of bzimage */
+	update_payload_info(bzimage, new_size);
+
+	/* TODO: update CRC */
+
+}
+
+static void fill_random(unsigned char *p, int n) {
+	srand(0);
+	int i;
+	for (i = 0; i < n; i++)
+		p[i] = rand();
+}
+
 static void print_sym(Elf_Ehdr *hdr, struct sym *s)
 {
 	info("sym:    %s\n", s->name);
@@ -267,18 +431,23 @@
 
 static void print_usage(char *e)
 {
-	printf("Usage %s [-s <System.map>] -b <vmlinux> -c <certfile>\n", e);
+	printf("Usage: %s [-s <System.map>] -b <vmlinux> -c <certfile>\n", e);
+	printf("       %s [-s <System.map>] -z <bzImage> -c <certfile>\n", e);
 }
 
 int main(int argc, char **argv)
 {
 	char *system_map_file = NULL;
 	char *vmlinux_file = NULL;
+	char *bzimage_file = NULL;
 	char *cert_file = NULL;
 	int vmlinux_size;
+	int bzimage_size;
 	int cert_size;
 	Elf_Ehdr *hdr;
 	char *cert;
+	char *bzimage = NULL;
+	struct zipper *z = NULL;
 	FILE *system_map;
 	unsigned long *lsize;
 	int *used;
@@ -286,7 +455,7 @@
 	Elf_Shdr *symtab = NULL;
 	struct sym cert_sym, lsize_sym, used_sym;
 
-	while ((opt = getopt(argc, argv, "b:c:s:")) != -1) {
+	while ((opt = getopt(argc, argv, "b:z:c:s:")) != -1) {
 		switch (opt) {
 		case 's':
 			system_map_file = optarg;
@@ -294,6 +463,9 @@
 		case 'b':
 			vmlinux_file = optarg;
 			break;
+		case 'z':
+			bzimage_file = optarg;
+			break;
 		case 'c':
 			cert_file = optarg;
 			break;
@@ -302,7 +474,9 @@
 		}
 	}
 
-	if (!vmlinux_file || !cert_file) {
+	if (!cert_file ||
+	(!vmlinux_file && !bzimage_file) ||
+	(vmlinux_file && bzimage_file)) {
 		print_usage(argv[0]);
 		exit(EXIT_FAILURE);
 	}
@@ -311,6 +485,16 @@
 	if (!cert)
 		exit(EXIT_FAILURE);
 
+	if (bzimage_file) {
+		bzimage = map_file(bzimage_file, &bzimage_size);
+		if (!bzimage)
+			exit(EXIT_FAILURE);
+
+		extract_vmlinux(bzimage, bzimage_size, &vmlinux_file, &z);
+		if (!vmlinux_file)
+			exit(EXIT_FAILURE);
+	}
+
 	hdr = map_file(vmlinux_file, &vmlinux_size);
 	if (!hdr)
 		exit(EXIT_FAILURE);
@@ -386,7 +570,7 @@
 	}
 
 	/* If the existing cert is the same, don't overwrite */
-	if (cert_size == *used &&
+	if (cert_size > 0 && cert_size == *used &&
 	    strncmp(cert_sym.content, cert, cert_size) == 0) {
 		warn("Certificate was already inserted.\n");
 		exit(EXIT_SUCCESS);
@@ -396,9 +580,11 @@
 		warn("Replacing previously inserted certificate.\n");
 
 	memcpy(cert_sym.content, cert, cert_size);
+
 	if (cert_size < cert_sym.size)
-		memset(cert_sym.content + cert_size,
-			0, cert_sym.size - cert_size);
+		/* This makes the reserved space incompressable */
+		fill_random(cert_sym.content + cert_size,
+				cert_sym.size - cert_size);
 
 	*lsize = *lsize + cert_size - *used;
 	*used = cert_size;
@@ -406,5 +592,15 @@
 						cert_sym.address);
 	info("Used %d bytes out of %d bytes reserved.\n", *used,
 						 cert_sym.size);
+
+	if (munmap(hdr, vmlinux_size) == -1) {
+		perror(vmlinux_file);
+		exit(EXIT_FAILURE);
+	}
+
+	if (bzimage) {
+		repack_image(bzimage, bzimage_size, vmlinux_file, z);
+	}
+
 	exit(EXIT_SUCCESS);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/conf.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/conf.c
@@ -838,6 +838,9 @@
 		break;
 	}
 
+	if (conf_errors())
+		exit(1);
+
 	if (sync_kconfig) {
 		name = getenv("KCONFIG_NOSILENTUPDATE");
 		if (name && *name) {
@@ -898,6 +901,9 @@
 		break;
 	}
 
+	if (sym_dep_errors())
+		exit(1);
+
 	if (input_mode == savedefconfig) {
 		if (conf_write_defconfig(defconfig_file)) {
 			fprintf(stderr, "n*** Error while saving defconfig to: %s\n\n",
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/confdata.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/confdata.c
@@ -173,6 +173,13 @@
 static const char *conf_filename;
 static int conf_lineno, conf_warnings;
 
+bool conf_errors(void)
+{
+	if (conf_warnings)
+		return getenv("KCONFIG_WERROR");
+	return false;
+}
+
 static void conf_warning(const char *fmt, ...)
 {
 	va_list ap;
@@ -348,10 +355,12 @@
 	FILE *in = NULL;
 	char   *line = NULL;
 	size_t  line_asize = 0;
-	char *p, *p2;
+	char *p, *p2, *val;
 	struct symbol *sym;
 	int i, def_flags;
+	const char *warn_unknown, *sym_name;
 
+	warn_unknown = getenv("KCONFIG_WARN_UNKNOWN_SYMBOLS");
 	if (name) {
 		in = zconf_fopen(name);
 	} else {
@@ -384,10 +393,12 @@
 
 			*p = '\0';
 
-			in = zconf_fopen(env);
+			name = env;
+
+			in = zconf_fopen(name);
 			if (in) {
 				conf_message("using defaults found in %s",
-					     env);
+					     name);
 				goto load;
 			}
 
@@ -426,71 +437,34 @@
 
 	while (compat_getline(&line, &line_asize, in) != -1) {
 		conf_lineno++;
-		sym = NULL;
 		if (line[0] == '#') {
-			if (memcmp(line + 2, CONFIG_, strlen(CONFIG_)))
+			if (line[1] != ' ')
+				continue;
+			p = line + 2;
+			if (memcmp(p, CONFIG_, strlen(CONFIG_)))
 				continue;
-			p = strchr(line + 2 + strlen(CONFIG_), ' ');
+			sym_name = p + strlen(CONFIG_);
+			p = strchr(sym_name, ' ');
 			if (!p)
 				continue;
 			*p++ = 0;
 			if (strncmp(p, "is not set", 10))
 				continue;
-			if (def == S_DEF_USER) {
-				sym = sym_find(line + 2 + strlen(CONFIG_));
-				if (!sym) {
-					conf_set_changed(true);
-					continue;
-				}
-			} else {
-				sym = sym_lookup(line + 2 + strlen(CONFIG_), 0);
-				if (sym->type == S_UNKNOWN)
-					sym->type = S_BOOLEAN;
-			}
-			if (sym->flags & def_flags) {
-				conf_warning("override: reassigning to symbol %s", sym->name);
-			}
-			switch (sym->type) {
-			case S_BOOLEAN:
-			case S_TRISTATE:
-				sym->def[def].tri = no;
-				sym->flags |= def_flags;
-				break;
-			default:
-				;
-			}
+
+			val = "n";
 		} else if (memcmp(line, CONFIG_, strlen(CONFIG_)) == 0) {
-			p = strchr(line + strlen(CONFIG_), '=');
+			sym_name = line + strlen(CONFIG_);
+			p = strchr(sym_name, '=');
 			if (!p)
 				continue;
 			*p++ = 0;
+			val = p;
 			p2 = strchr(p, '\n');
 			if (p2) {
 				*p2-- = 0;
 				if (*p2 == '\r')
 					*p2 = 0;
 			}
-
-			sym = sym_find(line + strlen(CONFIG_));
-			if (!sym) {
-				if (def == S_DEF_AUTO)
-					/*
-					 * Reading from include/config/auto.conf
-					 * If CONFIG_FOO previously existed in
-					 * auto.conf but it is missing now,
-					 * include/config/FOO must be touched.
-					 */
-					conf_touch_dep(line + strlen(CONFIG_));
-				else
-					conf_set_changed(true);
-				continue;
-			}
-
-			if (sym->flags & def_flags) {
-				conf_warning("override: reassigning to symbol %s", sym->name);
-			}
-			if (conf_set_sym_val(sym, def, def_flags, p))
-				continue;
 		} else {
 			if (line[0] != '\r' && line[0] != '\n')
 				conf_warning("unexpected data: %.*s",
@@ -499,6 +473,31 @@
 			continue;
 		}
 
+		sym = sym_find(sym_name);
+		if (!sym) {
+			if (def == S_DEF_AUTO) {
+				/*
+				 * Reading from include/config/auto.conf.
+				 * If CONFIG_FOO previously existed in auto.conf
+				 * but it is missing now, include/config/FOO
+				 * must be touched.
+				 */
+				conf_touch_dep(sym_name);
+			} else {
+				if (warn_unknown)
+					conf_warning("unknown symbol: %s", sym_name);
+
+				conf_set_changed(true);
+			}
+			continue;
+		}
+
+		if (sym->flags & def_flags)
+			conf_warning("override: reassigning to symbol %s", sym->name);
+
+		if (conf_set_sym_val(sym, def, def_flags, val))
+			continue;
+
 		if (sym && sym_is_choice_value(sym)) {
 			struct symbol *cs = prop_get_symbol(sym_get_choice_prop(sym));
 			switch (sym->def[def].tri) {
@@ -521,6 +520,7 @@
 	}
 	free(line);
 	fclose(in);
+
 	return 0;
 }
 
@@ -983,14 +983,19 @@
 
 static int conf_touch_deps(void)
 {
-	const char *name;
+	const char *name, *tmp;
 	struct symbol *sym;
 	int res, i;
 
-	strcpy(depfile_path, "include/config/");
-	depfile_prefix_len = strlen(depfile_path);
-
 	name = conf_get_autoconfig_name();
+	tmp = strrchr(name, '/');
+	depfile_prefix_len = tmp ? tmp - name + 1 : 0;
+	if (depfile_prefix_len + 1 > sizeof(depfile_path))
+		return -1;
+
+	strncpy(depfile_path, name, depfile_prefix_len);
+	depfile_path[depfile_prefix_len] = 0;
+
 	conf_read_simple(name, S_DEF_AUTO);
 	sym_calc_value(modules_sym);
 
@@ -1119,10 +1124,12 @@
 
 void conf_set_changed(bool val)
 {
-	if (conf_changed_callback && conf_changed != val)
-		conf_changed_callback();
+	bool changed = conf_changed != val;
 
 	conf_changed = val;
+
+	if (conf_changed_callback && changed)
+		conf_changed_callback();
 }
 
 bool conf_get_changed(void)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/expr.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/expr.c
@@ -397,35 +397,6 @@
 }
 
 /*
- * bool FOO!=n => FOO
- */
-struct expr *expr_trans_bool(struct expr *e)
-{
-	if (!e)
-		return NULL;
-	switch (e->type) {
-	case E_AND:
-	case E_OR:
-	case E_NOT:
-		e->left.expr = expr_trans_bool(e->left.expr);
-		e->right.expr = expr_trans_bool(e->right.expr);
-		break;
-	case E_UNEQUAL:
-		// FOO!=n -> FOO
-		if (e->left.sym->type == S_TRISTATE) {
-			if (e->right.sym == &symbol_no) {
-				e->type = E_SYMBOL;
-				e->right.sym = NULL;
-			}
-		}
-		break;
-	default:
-		;
-	}
-	return e;
-}
-
-/*
  * e1 || e2 -> ?
  */
 static struct expr *expr_join_or(struct expr *e1, struct expr *e2)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/expr.h
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/expr.h
@@ -296,7 +296,6 @@
 void expr_eliminate_eq(struct expr **ep1, struct expr **ep2);
 int expr_eq(struct expr *e1, struct expr *e2);
 tristate expr_calc_value(struct expr *e);
-struct expr *expr_trans_bool(struct expr *e);
 struct expr *expr_eliminate_dups(struct expr *e);
 struct expr *expr_transform(struct expr *e);
 int expr_contains_symbol(struct expr *dep, struct symbol *sym);
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/gconf-cfg.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/gconf-cfg.sh
@@ -3,14 +3,14 @@
 
 PKG="gtk+-2.0 gmodule-2.0 libglade-2.0"
 
-if [ -z "$(command -v pkg-config)" ]; then
+if [ -z "$(command -v ${HOSTPKG_CONFIG})" ]; then
 	echo >&2 "*"
-	echo >&2 "* 'make gconfig' requires 'pkg-config'. Please install it."
+	echo >&2 "* 'make gconfig' requires '${HOSTPKG_CONFIG}'. Please install it."
 	echo >&2 "*"
 	exit 1
 fi
 
-if ! pkg-config --exists $PKG; then
+if ! ${HOSTPKG_CONFIG} --exists $PKG; then
 	echo >&2 "*"
 	echo >&2 "* Unable to find the GTK+ installation. Please make sure that"
 	echo >&2 "* the GTK+ 2.0 development package is correctly installed."
@@ -19,12 +19,12 @@
 	exit 1
 fi
 
-if ! pkg-config --atleast-version=2.0.0 gtk+-2.0; then
+if ! ${HOSTPKG_CONFIG} --atleast-version=2.0.0 gtk+-2.0; then
 	echo >&2 "*"
 	echo >&2 "* GTK+ is present but version >= 2.0.0 is required."
 	echo >&2 "*"
 	exit 1
 fi
 
-echo cflags=\"$(pkg-config --cflags $PKG)\"
-echo libs=\"$(pkg-config --libs $PKG)\"
+echo cflags=\"$(${HOSTPKG_CONFIG} --cflags $PKG)\"
+echo libs=\"$(${HOSTPKG_CONFIG} --libs $PKG)\"
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/gconf.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/gconf.c
@@ -1481,7 +1481,6 @@
 
 	conf_parse(name);
 	fixup_rootmenu(&rootmenu);
-	conf_read(NULL);
 
 	/* Load the interface and connect signals */
 	init_main_window(glade_file);
@@ -1489,6 +1488,8 @@
 	init_left_tree();
 	init_right_tree();
 
+	conf_read(NULL);
+
 	switch (view_mode) {
 	case SINGLE_VIEW:
 		display_tree_part();
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/lexer.l
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/lexer.l
@@ -301,8 +301,11 @@
 	new_string();
 	append_string(in, n);
 
-	/* get the whole line because we do not know the end of token. */
-	while ((c = input()) != EOF) {
+	/*
+	 * get the whole line because we do not know the end of token.
+	 * input() returns 0 (not EOF!) when it reachs the end of file.
+	 */
+	while ((c = input()) != 0) {
 		if (c == '\n') {
 			unput(c);
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/lkc.h
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/lkc.h
@@ -46,7 +46,9 @@
 /* confdata.c and expr.c */
 static inline void xfwrite(const void *str, size_t len, size_t count, FILE *out)
 {
-	assert(len != 0);
+	//assert(len != 0);
+	if (len == 0)
+		return;
 
 	if (fwrite(str, len, count, out) != count)
 		fprintf(stderr, "Error in writing or end of file.\n");
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/lkc_proto.h
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/lkc_proto.h
@@ -12,6 +12,7 @@
 bool conf_get_changed(void);
 void conf_set_changed_callback(void (*fn)(void));
 void conf_set_message_callback(void (*fn)(const char *s));
+bool conf_errors(void);
 
 /* symbol.c */
 extern struct symbol * symbol_hash[SYMBOL_HASHSIZE];
@@ -22,6 +23,7 @@
 struct symbol ** sym_re_search(const char *pattern);
 const char * sym_type_name(enum symbol_type type);
 void sym_calc_value(struct symbol *sym);
+bool sym_dep_errors(void);
 enum symbol_type sym_get_type(struct symbol *sym);
 bool sym_tristate_within_range(struct symbol *sym,tristate tri);
 bool sym_set_tristate_value(struct symbol *sym,tristate tri);
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/mconf-cfg.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/mconf-cfg.sh
@@ -4,16 +4,16 @@
 PKG="ncursesw"
 PKG2="ncurses"
 
-if [ -n "$(command -v pkg-config)" ]; then
-	if pkg-config --exists $PKG; then
-		echo cflags=\"$(pkg-config --cflags $PKG)\"
-		echo libs=\"$(pkg-config --libs $PKG)\"
+if [ -n "$(command -v ${HOSTPKG_CONFIG})" ]; then
+	if ${HOSTPKG_CONFIG} --exists $PKG; then
+		echo cflags=\"$(${HOSTPKG_CONFIG} --cflags $PKG)\"
+		echo libs=\"$(${HOSTPKG_CONFIG} --libs $PKG)\"
 		exit 0
 	fi
 
-	if pkg-config --exists $PKG2; then
-		echo cflags=\"$(pkg-config --cflags $PKG2)\"
-		echo libs=\"$(pkg-config --libs $PKG2)\"
+	if ${HOSTPKG_CONFIG} --exists $PKG2; then
+		echo cflags=\"$(${HOSTPKG_CONFIG} --cflags $PKG2)\"
+		echo libs=\"$(${HOSTPKG_CONFIG} --libs $PKG2)\"
 		exit 0
 	fi
 fi
@@ -46,7 +46,7 @@
 echo >&2 "* Install ncurses (ncurses-devel or libncurses-dev"
 echo >&2 "* depending on your distribution)."
 echo >&2 "*"
-echo >&2 "* You may also need to install pkg-config to find the"
+echo >&2 "* You may also need to install ${HOSTPKG_CONFIG} to find the"
 echo >&2 "* ncurses installed in a non-default location."
 echo >&2 "*"
 exit 1
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/menu.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/menu.c
@@ -380,8 +380,6 @@
 				dep = expr_transform(dep);
 				dep = expr_alloc_and(expr_copy(basedep), dep);
 				dep = expr_eliminate_dups(dep);
-				if (menu->sym && menu->sym->type != S_TRISTATE)
-					dep = expr_trans_bool(dep);
 				prop->visible.expr = dep;
 
 				/*
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/merge_config.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/merge_config.sh
@@ -160,6 +160,8 @@
 			sed -i "/$CFG[ =]/d" $MERGE_FILE
 		fi
 	done
+	# In case the previous file lacks a new line at the end
+	echo >> $TMP_FILE
 	cat $MERGE_FILE >> $TMP_FILE
 done
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/nconf-cfg.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/nconf-cfg.sh
@@ -4,16 +4,16 @@
 PKG="ncursesw menuw panelw"
 PKG2="ncurses menu panel"
 
-if [ -n "$(command -v pkg-config)" ]; then
-	if pkg-config --exists $PKG; then
-		echo cflags=\"$(pkg-config --cflags $PKG)\"
-		echo libs=\"$(pkg-config --libs $PKG)\"
+if [ -n "$(command -v ${HOSTPKG_CONFIG})" ]; then
+	if ${HOSTPKG_CONFIG} --exists $PKG; then
+		echo cflags=\"$(${HOSTPKG_CONFIG} --cflags $PKG)\"
+		echo libs=\"$(${HOSTPKG_CONFIG} --libs $PKG)\"
 		exit 0
 	fi
 
-	if pkg-config --exists $PKG2; then
-		echo cflags=\"$(pkg-config --cflags $PKG2)\"
-		echo libs=\"$(pkg-config --libs $PKG2)\"
+	if ${HOSTPKG_CONFIG} --exists $PKG2; then
+		echo cflags=\"$(${HOSTPKG_CONFIG} --cflags $PKG2)\"
+		echo libs=\"$(${HOSTPKG_CONFIG} --libs $PKG2)\"
 		exit 0
 	fi
 fi
@@ -44,7 +44,7 @@
 echo >&2 "* Install ncurses (ncurses-devel or libncurses-dev"
 echo >&2 "* depending on your distribution)."
 echo >&2 "*"
-echo >&2 "* You may also need to install pkg-config to find the"
+echo >&2 "* You may also need to install ${HOSTPKG_CONFIG} to find the"
 echo >&2 "* ncurses installed in a non-default location."
 echo >&2 "*"
 exit 1
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/preprocess.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/preprocess.c
@@ -141,7 +141,7 @@
 static char *do_shell(int argc, char *argv[])
 {
 	FILE *p;
-	char buf[256];
+	char buf[4096];
 	char *cmd;
 	size_t nread;
 	int i;
@@ -396,6 +396,9 @@
 
 		p++;
 	}
+
+	if (new_argc >= FUNCTION_MAX_ARGS)
+		pperror("too many function arguments");
 	new_argv[new_argc++] = prev;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/qconf-cfg.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/qconf-cfg.sh
@@ -3,22 +3,22 @@
 
 PKG="Qt5Core Qt5Gui Qt5Widgets"
 
-if [ -z "$(command -v pkg-config)" ]; then
+if [ -z "$(command -v ${HOSTPKG_CONFIG})" ]; then
 	echo >&2 "*"
-	echo >&2 "* 'make xconfig' requires 'pkg-config'. Please install it."
+	echo >&2 "* 'make xconfig' requires '${HOSTPKG_CONFIG}'. Please install it."
 	echo >&2 "*"
 	exit 1
 fi
 
-if pkg-config --exists $PKG; then
-	echo cflags=\"-std=c++11 -fPIC $(pkg-config --cflags $PKG)\"
-	echo libs=\"$(pkg-config --libs $PKG)\"
-	echo moc=\"$(pkg-config --variable=host_bins Qt5Core)/moc\"
+if ${HOSTPKG_CONFIG} --exists $PKG; then
+	echo cflags=\"-std=c++11 -fPIC $(${HOSTPKG_CONFIG} --cflags $PKG)\"
+	echo libs=\"$(${HOSTPKG_CONFIG} --libs $PKG)\"
+	echo moc=\"$(${HOSTPKG_CONFIG} --variable=host_bins Qt5Core)/moc\"
 	exit 0
 fi
 
 echo >&2 "*"
-echo >&2 "* Could not find Qt5 via pkg-config."
+echo >&2 "* Could not find Qt5 via ${HOSTPKG_CONFIG}."
 echo >&2 "* Please install Qt5 and make sure it's in PKG_CONFIG_PATH"
 echo >&2 "*"
 exit 1
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/qconf.cc
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/qconf.cc
@@ -1172,7 +1172,7 @@
 {
 	QByteArray str = url.toEncoded();
 	const std::size_t count = str.size();
-	char *data = new char[count + 1];
+	char *data = new char[count + 2];  // '$' + '\0'
 	struct symbol **result;
 	struct menu *m = NULL;
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kconfig/symbol.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/kconfig/symbol.c
@@ -13,18 +13,21 @@
 
 struct symbol symbol_yes = {
 	.name = "y",
+	.type = S_TRISTATE,
 	.curr = { "y", yes },
 	.flags = SYMBOL_CONST|SYMBOL_VALID,
 };
 
 struct symbol symbol_mod = {
 	.name = "m",
+	.type = S_TRISTATE,
 	.curr = { "m", mod },
 	.flags = SYMBOL_CONST|SYMBOL_VALID,
 };
 
 struct symbol symbol_no = {
 	.name = "n",
+	.type = S_TRISTATE,
 	.curr = { "n", no },
 	.flags = SYMBOL_CONST|SYMBOL_VALID,
 };
@@ -37,6 +40,7 @@
 
 struct symbol *modules_sym;
 static tristate modules_val;
+static int sym_warnings;
 
 enum symbol_type sym_get_type(struct symbol *sym)
 {
@@ -122,9 +126,9 @@
 static void sym_validate_range(struct symbol *sym)
 {
 	struct property *prop;
+	struct symbol *range_sym;
 	int base;
 	long long val, val2;
-	char str[64];
 
 	switch (sym->type) {
 	case S_INT:
@@ -140,17 +144,15 @@
 	if (!prop)
 		return;
 	val = strtoll(sym->curr.val, NULL, base);
-	val2 = sym_get_range_val(prop->expr->left.sym, base);
+	range_sym = prop->expr->left.sym;
+	val2 = sym_get_range_val(range_sym, base);
 	if (val >= val2) {
-		val2 = sym_get_range_val(prop->expr->right.sym, base);
+		range_sym = prop->expr->right.sym;
+		val2 = sym_get_range_val(range_sym, base);
 		if (val <= val2)
 			return;
 	}
-	if (sym->type == S_INT)
-		sprintf(str, "%lld", val2);
-	else
-		sprintf(str, "0x%llx", val2);
-	sym->curr.val = xstrdup(str);
+	sym->curr.val = range_sym->curr.val;
 }
 
 static void sym_set_changed(struct symbol *sym)
@@ -319,6 +321,15 @@
 			       "  Selected by [m]:\n");
 
 	fputs(str_get(&gs), stderr);
+	str_free(&gs);
+	sym_warnings++;
+}
+
+bool sym_dep_errors(void)
+{
+	if (sym_warnings)
+		return getenv("KCONFIG_WERROR");
+	return false;
 }
 
 void sym_calc_value(struct symbol *sym)
@@ -777,8 +788,7 @@
 		case no:
 			return "n";
 		case mod:
-			sym_calc_value(modules_sym);
-			return (modules_sym->curr.tri == no) ? "n" : "m";
+			return "m";
 		case yes:
 			return "y";
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/kernel-doc
+++ linux-xilinx-zynqmp-5.15.0/scripts/kernel-doc
@@ -1245,6 +1245,13 @@
 	$members =~ s/\s*CRYPTO_MINALIGN_ATTR/ /gos;
 	$members =~ s/\s*____cacheline_aligned_in_smp/ /gos;
 	$members =~ s/\s*____cacheline_aligned/ /gos;
+	# unwrap struct_group():
+	# - first eat non-declaration parameters and rewrite for final match
+	# - then remove macro, outer parens, and trailing semicolon
+	$members =~ s/\bstruct_group\s*\(([^,]*,)/STRUCT_GROUP(/gos;
+	$members =~ s/\bstruct_group_(attr|tagged)\s*\(([^,]*,){2}/STRUCT_GROUP(/gos;
+	$members =~ s/\b__struct_group\s*\(([^,]*,){3}/STRUCT_GROUP(/gos;
+	$members =~ s/\bSTRUCT_GROUP(\(((?:(?>[^)(]+)|(?1))*)\))[^;]*;/$2/gos;
 
 	my $args = qr{([^,)]+)};
 	# replace DECLARE_BITMAP
@@ -1256,6 +1263,8 @@
 	$members =~ s/DECLARE_KFIFO\s*\($args,\s*$args,\s*$args\)/$2 \*$1/gos;
 	# replace DECLARE_KFIFO_PTR
 	$members =~ s/DECLARE_KFIFO_PTR\s*\($args,\s*$args\)/$2 \*$1/gos;
+	# replace DECLARE_FLEX_ARRAY
+	$members =~ s/(?:__)?DECLARE_FLEX_ARRAY\s*\($args,\s*$args\)/$1 $2\[\]/gos;
 	my $declaration = $members;
 
 	# Split nested struct/union elements as newer ones
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/ld-version.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/ld-version.sh
@@ -57,9 +57,11 @@
 	fi
 fi
 
-# Some distributions append a package release number, as in 2.34-4.fc32
-# Trim the hyphen and any characters that follow.
-version=${version%-*}
+# There may be something after the version, such as a distribution's package
+# release number (like Fedora's "2.34-4.fc32") or punctuation (like LLD briefly
+# added before the "compatible with GNU linkers" string), so remove everything
+# after just numbers and periods.
+version=${version%%[!0-9.]*}
 
 cversion=$(get_canonical_version $version)
 min_cversion=$(get_canonical_version $min_version)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/leaking_addresses.pl
+++ linux-xilinx-zynqmp-5.15.0/scripts/leaking_addresses.pl
@@ -455,8 +455,9 @@
 
 	open my $fh, "<", $file or return;
 	while ( <$fh> ) {
+		chomp;
 		if (may_leak_address($_)) {
-			print $file . ': ' . $_;
+			printf("$file: $_\n");
 		}
 	}
 	close $fh;
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/link-vmlinux.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/link-vmlinux.sh
@@ -120,6 +120,9 @@
 
 	if [ -n "${CONFIG_VMLINUX_VALIDATION}" ]; then
 		objtoolopt="${objtoolopt} --noinstr"
+		if is_enabled CONFIG_CPU_UNRET_ENTRY; then
+			objtoolopt="${objtoolopt} --unret"
+		fi
 	fi
 
 	if [ -n "${objtoolopt}" ]; then
@@ -139,6 +142,9 @@
 		if [ -n "${CONFIG_X86_SMAP}" ]; then
 			objtoolopt="${objtoolopt} --uaccess"
 		fi
+		if [ -n "${CONFIG_SLS}" ]; then
+			objtoolopt="${objtoolopt} --sls"
+		fi
 		info OBJTOOL ${1}
 		tools/objtool/objtool ${objtoolcmd} ${objtoolopt} ${1}
 	fi
@@ -205,7 +211,6 @@
 gen_btf()
 {
 	local pahole_ver
-	local extra_paholeopt=
 
 	if ! [ -x "$(command -v ${PAHOLE})" ]; then
 		echo >&2 "BTF: ${1}: pahole (${PAHOLE}) is not available"
@@ -220,16 +225,8 @@
 
 	vmlinux_link ${1}
 
-	if [ "${pahole_ver}" -ge "118" ] && [ "${pahole_ver}" -le "121" ]; then
-		# pahole 1.18 through 1.21 can't handle zero-sized per-CPU vars
-		extra_paholeopt="${extra_paholeopt} --skip_encoding_btf_vars"
-	fi
-	if [ "${pahole_ver}" -ge "121" ]; then
-		extra_paholeopt="${extra_paholeopt} --btf_gen_floats"
-	fi
-
 	info "BTF" ${2}
-	LLVM_OBJCOPY="${OBJCOPY}" ${PAHOLE} -J ${extra_paholeopt} ${1}
+	LLVM_OBJCOPY="${OBJCOPY}" ${PAHOLE} -J ${PAHOLE_FLAGS} ${1}
 
 	# Create ${2} which contains just .BTF section but no symbols. Add
 	# SHF_ALLOC because .BTF will be part of the vmlinux image. --strip-all
@@ -239,8 +236,13 @@
 	${OBJCOPY} --only-section=.BTF --set-section-flags .BTF=alloc,readonly \
 		--strip-all ${1} ${2} 2>/dev/null
 	# Change e_type to ET_REL so that it can be used to link final vmlinux.
-	# Unlike GNU ld, lld does not allow an ET_EXEC input.
-	printf '\1' | dd of=${2} conv=notrunc bs=1 seek=16 status=none
+	# GNU ld 2.35+ and lld do not allow an ET_EXEC input.
+	if [ -n "${CONFIG_CPU_BIG_ENDIAN}" ]; then
+		et_rel='\0\1'
+	else
+		et_rel='\1\0'
+	fi
+	printf "${et_rel}" | dd of=${2} conv=notrunc bs=1 seek=16 status=none
 }
 
 # Create ${2} .S file with all symbols from the ${1} object file
@@ -276,7 +278,7 @@
 	vmlinux_link ${kallsyms_vmlinux} "${kallsymso_prev}" ${btf_vmlinux_bin_o}
 	kallsyms ${kallsyms_vmlinux} ${kallsyms_S}
 
-	info AS ${kallsyms_S}
+	info AS ${kallsymso}
 	${CC} ${NOSTDINC_FLAGS} ${LINUXINCLUDE} ${KBUILD_CPPFLAGS} \
 	      ${KBUILD_AFLAGS} ${KBUILD_AFLAGS_KERNEL} \
 	      -c -o ${kallsymso} ${kallsyms_S}
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/mksysmap
+++ linux-xilinx-zynqmp-5.15.0/scripts/mksysmap
@@ -41,4 +41,4 @@
 # so we just ignore them to let readprofile continue to work.
 # (At least sparc64 has __crc_ in the middle).
 
-$NM -n $1 | grep -v '\( [aNUw] \)\|\(__crc_\)\|\( \$[adt]\)\|\( \.L\)' > $2
+$NM -n $1 | grep -v '\( [aNUw] \)\|\(__crc_\)\|\( \$[adt]\)\|\( \.L\)\|\( L0\)' > $2
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/mod/file2alias.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/mod/file2alias.c
@@ -732,8 +732,8 @@
 
 	for (i = min / BITS_PER_LONG; i < max / BITS_PER_LONG + 1; i++)
 		arr[i] = TO_NATIVE(arr[i]);
-	for (i = min; i < max; i++)
-		if (arr[i / BITS_PER_LONG] & (1L << (i%BITS_PER_LONG)))
+	for (i = min; i <= max; i++)
+		if (arr[i / BITS_PER_LONG] & (1ULL << (i%BITS_PER_LONG)))
 			sprintf(alias + strlen(alias), "%X,*", i);
 }
 
@@ -799,10 +799,7 @@
 		char *alias)
 {
 	DEF_FIELD_ADDR(symval, eisa_device_id, sig);
-	if (sig[0])
-		sprintf(alias, EISA_DEVICE_MODALIAS_FMT "*", *sig);
-	else
-		strcat(alias, "*");
+	sprintf(alias, EISA_DEVICE_MODALIAS_FMT "*", *sig);
 	return 1;
 }
 
@@ -1339,13 +1336,13 @@
 /* Looks like: tee:uuid */
 static int do_tee_entry(const char *filename, void *symval, char *alias)
 {
-	DEF_FIELD(symval, tee_client_device_id, uuid);
+	DEF_FIELD_ADDR(symval, tee_client_device_id, uuid);
 
 	sprintf(alias, "tee:%02x%02x%02x%02x-%02x%02x-%02x%02x-%02x%02x-%02x%02x%02x%02x%02x%02x",
-		uuid.b[0], uuid.b[1], uuid.b[2], uuid.b[3], uuid.b[4],
-		uuid.b[5], uuid.b[6], uuid.b[7], uuid.b[8], uuid.b[9],
-		uuid.b[10], uuid.b[11], uuid.b[12], uuid.b[13], uuid.b[14],
-		uuid.b[15]);
+		uuid->b[0], uuid->b[1], uuid->b[2], uuid->b[3], uuid->b[4],
+		uuid->b[5], uuid->b[6], uuid->b[7], uuid->b[8], uuid->b[9],
+		uuid->b[10], uuid->b[11], uuid->b[12], uuid->b[13], uuid->b[14],
+		uuid->b[15]);
 
 	add_wildcard(alias);
 	return 1;
@@ -1547,7 +1544,7 @@
 	/* First handle the "special" cases */
 	if (sym_is(name, namelen, "usb"))
 		do_usb_table(symval, sym->st_size, mod);
-	if (sym_is(name, namelen, "of"))
+	else if (sym_is(name, namelen, "of"))
 		do_of_table(symval, sym->st_size, mod);
 	else if (sym_is(name, namelen, "pnp"))
 		do_pnp_device_entry(symval, sym->st_size, mod);
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/mod/modpost.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/mod/modpost.c
@@ -658,6 +658,11 @@
 		    strstarts(symname, "_savevr_") ||
 		    strcmp(symname, ".TOC.") == 0)
 			return 1;
+
+	if (info->hdr->e_machine == EM_S390)
+		/* Expoline thunks are linked on all kernel modules during final link of .ko */
+		if (strstarts(symname, "__s390_indirect_jump_r"))
+			return 1;
 	/* Do not ignore this symbol */
 	return 0;
 }
@@ -669,7 +674,7 @@
 	unsigned int crc;
 
 	if (sym->st_shndx == SHN_UNDEF) {
-		warn("EXPORT symbol \"%s\" [%s%s] version ...\n"
+		warn("EXPORT symbol \"%s\" [%s%s] version generation failed, symbol will not be versioned.\n"
 		     "Is \"%s\" prototyped in <asm/asm-prototypes.h>?\n",
 		     symname, mod->name, mod->is_vmlinux ? "" : ".ko",
 		     symname);
@@ -936,11 +941,11 @@
 #define ALL_EXIT_SECTIONS EXIT_SECTIONS, ALL_XXXEXIT_SECTIONS
 
 #define DATA_SECTIONS ".data", ".data.rel"
-#define TEXT_SECTIONS ".text", ".text.unlikely", ".sched.text", \
+#define TEXT_SECTIONS ".text", ".text.*", ".sched.text", \
 		".kprobes.text", ".cpuidle.text", ".noinstr.text"
 #define OTHER_TEXT_SECTIONS ".ref.text", ".head.text", ".spinlock.text", \
-		".fixup", ".entry.text", ".exception.text", ".text.*", \
-		".coldtext", ".softirqentry.text"
+		".fixup", ".entry.text", ".exception.text", \
+		".coldtext", ".softirqentry.text", ".irqentry.text"
 
 #define INIT_SECTIONS      ".init.*"
 #define MEM_INIT_SECTIONS  ".meminit.*"
@@ -1108,7 +1113,7 @@
 },
 /* Do not export init/exit functions or data */
 {
-	.fromsec = { "__ksymtab*", NULL },
+	.fromsec = { "___ksymtab*", NULL },
 	.bad_tosec = { INIT_SECTIONS, EXIT_SECTIONS, NULL },
 	.mismatch = EXPORT_TO_INIT_EXIT,
 	.symbol_white_list = { DEFAULT_SYMBOL_WHITE_LIST, NULL },
@@ -1260,7 +1265,8 @@
 
 static inline int is_arm_mapping_symbol(const char *str)
 {
-	return str[0] == '$' && strchr("axtd", str[1])
+	return str[0] == '$' &&
+	       (str[1] == 'a' || str[1] == 'd' || str[1] == 't' || str[1] == 'x')
 	       && (str[2] == '\0' || str[2] == '.');
 }
 
@@ -1301,6 +1307,10 @@
 	if (relsym->st_name != 0)
 		return relsym;
 
+	/*
+	 * Strive to find a better symbol name, but the resulting name may not
+	 * match the symbol referenced in the original code.
+	 */
 	relsym_secindex = get_secindex(elf, relsym);
 	for (sym = elf->symtab_start; sym < elf->symtab_stop; sym++) {
 		if (get_secindex(elf, sym) != relsym_secindex)
@@ -1605,49 +1615,12 @@
 
 static int is_executable_section(struct elf_info* elf, unsigned int section_index)
 {
-	if (section_index > elf->num_sections)
+	if (section_index >= elf->num_sections)
 		fatal("section_index is outside elf->num_sections!\n");
 
 	return ((elf->sechdrs[section_index].sh_flags & SHF_EXECINSTR) == SHF_EXECINSTR);
 }
 
-/*
- * We rely on a gross hack in section_rel[a]() calling find_extable_entry_size()
- * to know the sizeof(struct exception_table_entry) for the target architecture.
- */
-static unsigned int extable_entry_size = 0;
-static void find_extable_entry_size(const char* const sec, const Elf_Rela* r)
-{
-	/*
-	 * If we're currently checking the second relocation within __ex_table,
-	 * that relocation offset tells us the offsetof(struct
-	 * exception_table_entry, fixup) which is equal to sizeof(struct
-	 * exception_table_entry) divided by two.  We use that to our advantage
-	 * since there's no portable way to get that size as every architecture
-	 * seems to go with different sized types.  Not pretty but better than
-	 * hard-coding the size for every architecture..
-	 */
-	if (!extable_entry_size)
-		extable_entry_size = r->r_offset * 2;
-}
-
-static inline bool is_extable_fault_address(Elf_Rela *r)
-{
-	/*
-	 * extable_entry_size is only discovered after we've handled the
-	 * _second_ relocation in __ex_table, so only abort when we're not
-	 * handling the first reloc and extable_entry_size is zero.
-	 */
-	if (r->r_offset && extable_entry_size == 0)
-		fatal("extable_entry size hasn't been discovered!\n");
-
-	return ((r->r_offset == 0) ||
-		(r->r_offset % extable_entry_size == 0));
-}
-
-#define is_second_extable_reloc(Start, Cur, Sec)			\
-	(((Cur) == (Start) + 1) && (strcmp("__ex_table", (Sec)) == 0))
-
 static void report_extable_warnings(const char* modname, struct elf_info* elf,
 				    const struct sectioncheck* const mismatch,
 				    Elf_Rela* r, Elf_Sym* sym,
@@ -1704,22 +1677,9 @@
 		      "You might get more information about where this is\n"
 		      "coming from by using scripts/check_extable.sh %s\n",
 		      fromsec, (long)r->r_offset, tosec, modname);
-	else if (!is_executable_section(elf, get_secindex(elf, sym))) {
-		if (is_extable_fault_address(r))
-			fatal("The relocation at %s+0x%lx references\n"
-			      "section \"%s\" which is not executable, IOW\n"
-			      "it is not possible for the kernel to fault\n"
-			      "at that address.  Something is seriously wrong\n"
-			      "and should be fixed.\n",
-			      fromsec, (long)r->r_offset, tosec);
-		else
-			fatal("The relocation at %s+0x%lx references\n"
-			      "section \"%s\" which is not executable, IOW\n"
-			      "the kernel will fault if it ever tries to\n"
-			      "jump to it.  Something is seriously wrong\n"
-			      "and should be fixed.\n",
-			      fromsec, (long)r->r_offset, tosec);
-	}
+	else if (!is_executable_section(elf, get_secindex(elf, sym)))
+		error("%s+0x%lx references non-executable section '%s'\n",
+		      fromsec, (long)r->r_offset, tosec);
 }
 
 static void check_section_mismatch(const char *modname, struct elf_info *elf,
@@ -1780,19 +1740,33 @@
 #define	R_ARM_THM_JUMP19	51
 #endif
 
+static int32_t sign_extend32(int32_t value, int index)
+{
+	uint8_t shift = 31 - index;
+
+	return (int32_t)(value << shift) >> shift;
+}
+
 static int addend_arm_rel(struct elf_info *elf, Elf_Shdr *sechdr, Elf_Rela *r)
 {
 	unsigned int r_typ = ELF_R_TYPE(r->r_info);
+	Elf_Sym *sym = elf->symtab_start + ELF_R_SYM(r->r_info);
+	void *loc = reloc_location(elf, sechdr, r);
+	uint32_t inst;
+	int32_t offset;
 
 	switch (r_typ) {
 	case R_ARM_ABS32:
-		/* From ARM ABI: (S + A) | T */
-		r->r_addend = (int)(long)
-			      (elf->symtab_start + ELF_R_SYM(r->r_info));
+		inst = TO_NATIVE(*(uint32_t *)loc);
+		r->r_addend = inst + sym->st_value;
 		break;
 	case R_ARM_PC24:
 	case R_ARM_CALL:
 	case R_ARM_JUMP24:
+		inst = TO_NATIVE(*(uint32_t *)loc);
+		offset = sign_extend32((inst & 0x00ffffff) << 2, 25);
+		r->r_addend = offset + sym->st_value + 8;
+		break;
 	case R_ARM_THM_CALL:
 	case R_ARM_THM_JUMP24:
 	case R_ARM_THM_JUMP19:
@@ -1870,8 +1844,6 @@
 		/* Skip special sections */
 		if (is_shndx_special(sym->st_shndx))
 			continue;
-		if (is_second_extable_reloc(start, rela, fromsec))
-			find_extable_entry_size(fromsec, &r);
 		check_section_mismatch(modname, elf, &r, sym, fromsec);
 	}
 }
@@ -1930,8 +1902,6 @@
 		/* Skip special sections */
 		if (is_shndx_special(sym->st_shndx))
 			continue;
-		if (is_second_extable_reloc(start, rel, fromsec))
-			find_extable_entry_size(fromsec, &r);
 		check_section_mismatch(modname, elf, &r, sym, fromsec);
 	}
 }
@@ -1971,7 +1941,7 @@
 
 	if (n && s[n]) {
 		size_t m = strspn(s + n + 1, "0123456789");
-		if (m && (s[n + m] == '.' || s[n + m] == 0))
+		if (m && (s[n + m + 1] == '.' || s[n + m + 1] == 0))
 			s[n] = 0;
 
 		/* strip trailing .lto */
@@ -2246,6 +2216,8 @@
 {
 	if (strstarts(name, "drivers/staging"))
 		buf_printf(b, "\nMODULE_INFO(staging, \"Y\");\n");
+	if (strstarts(name, "ubuntu/staging"))
+		buf_printf(b, "\nMODULE_INFO(staging, \"Y\");\n");
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/mod/sumversion.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/mod/sumversion.c
@@ -328,7 +328,12 @@
 
 	/* Sum all files in the same dir or subdirs. */
 	while ((line = get_line(&pos))) {
-		char* p = line;
+		char* p;
+
+		/* trim the leading spaces away */
+		while (isspace(*line))
+			line++;
+		p = line;
 
 		if (strncmp(line, "source_", sizeof("source_")-1) == 0) {
 			p = strrchr(line, ' ');
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/module.lds.S
+++ linux-xilinx-zynqmp-5.15.0/scripts/module.lds.S
@@ -27,6 +27,8 @@
 	.ctors			0 : ALIGN(8) { *(SORT(.ctors.*)) *(.ctors) }
 	.init_array		0 : ALIGN(8) { *(SORT(.init_array.*)) *(.init_array) }
 
+	.altinstructions	0 : ALIGN(8) { KEEP(*(.altinstructions)) }
+	__bug_table		0 : ALIGN(8) { KEEP(*(__bug_table)) }
 	__jump_table		0 : ALIGN(8) { KEEP(*(__jump_table)) }
 
 	__patchable_function_entries : { *(__patchable_function_entries) }
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/package/mkdebian
+++ linux-xilinx-zynqmp-5.15.0/scripts/package/mkdebian
@@ -236,7 +236,7 @@
 	KBUILD_BUILD_VERSION=${revision} -f \$(srctree)/Makefile intdeb-pkg
 
 clean:
-	rm -rf debian/*tmp debian/files
+	rm -rf debian/files debian/linux-*
 	\$(MAKE) clean
 
 binary: binary-arch
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/package/mkspec
+++ linux-xilinx-zynqmp-5.15.0/scripts/package/mkspec
@@ -85,10 +85,10 @@
 	mkdir -p %{buildroot}/boot
 	%ifarch ia64
 	mkdir -p %{buildroot}/boot/efi
-	cp \$($MAKE image_name) %{buildroot}/boot/efi/vmlinuz-$KERNELRELEASE
+	cp \$($MAKE -s image_name) %{buildroot}/boot/efi/vmlinuz-$KERNELRELEASE
 	ln -s efi/vmlinuz-$KERNELRELEASE %{buildroot}/boot/
 	%else
-	cp \$($MAKE image_name) %{buildroot}/boot/vmlinuz-$KERNELRELEASE
+	cp \$($MAKE -s image_name) %{buildroot}/boot/vmlinuz-$KERNELRELEASE
 	%endif
 $M	$MAKE %{?_smp_mflags} INSTALL_MOD_PATH=%{buildroot} modules_install
 	$MAKE %{?_smp_mflags} INSTALL_HDR_PATH=%{buildroot}/usr headers_install
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/pahole-flags.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/pahole-flags.sh
@@ -0,0 +1,27 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0
+
+extra_paholeopt=
+
+if ! [ -x "$(command -v ${PAHOLE})" ]; then
+	exit 0
+fi
+
+pahole_ver=$($(dirname $0)/pahole-version.sh ${PAHOLE})
+
+if [ "${pahole_ver}" -ge "118" ] && [ "${pahole_ver}" -le "121" ]; then
+	# pahole 1.18 through 1.21 can't handle zero-sized per-CPU vars
+	extra_paholeopt="${extra_paholeopt} --skip_encoding_btf_vars"
+fi
+if [ "${pahole_ver}" -ge "121" ]; then
+	extra_paholeopt="${extra_paholeopt} --btf_gen_floats"
+fi
+
+if [ "${pahole_ver}" -ge "124" ]; then
+	extra_paholeopt="${extra_paholeopt} --skip_encoding_btf_enum64"
+fi
+if [ "${pahole_ver}" -ge "125" ]; then
+	extra_paholeopt="${extra_paholeopt} --skip_encoding_btf_inconsistent_proto --btf_gen_optimized"
+fi
+
+echo ${extra_paholeopt}
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/pahole-version.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/pahole-version.sh
@@ -0,0 +1,13 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0
+#
+# Usage: $ ./pahole-version.sh pahole
+#
+# Prints pahole's version in a 3-digit form, such as 119 for v1.19.
+
+if [ ! -x "$(command -v "$@")" ]; then
+	echo 0
+	exit 1
+fi
+
+"$@" --version | sed -E 's/v([0-9]+)\.([0-9]+)/\1\2/'
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/recordmcount.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/recordmcount.c
@@ -102,6 +102,7 @@
 {
 	size_t cnt = count;
 	off_t idx = 0;
+	void *p = NULL;
 
 	file_updated = 1;
 
@@ -109,7 +110,10 @@
 		off_t aoffset = (file_ptr + count) - file_end;
 
 		if (aoffset > file_append_size) {
-			file_append = realloc(file_append, aoffset);
+			p = realloc(file_append, aoffset);
+			if (!p)
+				free(file_append);
+			file_append = p;
 			file_append_size = aoffset;
 		}
 		if (!file_append) {
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/recordmcount.pl
+++ linux-xilinx-zynqmp-5.15.0/scripts/recordmcount.pl
@@ -219,7 +219,7 @@
 
 } elsif ($arch eq "s390" && $bits == 64) {
     if ($cc =~ /-DCC_USING_HOTPATCH/) {
-	$mcount_regex = "^\\s*([0-9a-fA-F]+):\\s*c0 04 00 00 00 00\\s*brcl\\s*0,[0-9a-f]+ <([^\+]*)>\$";
+	$mcount_regex = "^\\s*([0-9a-fA-F]+):\\s*c0 04 00 00 00 00\\s*(brcl\\s*0,|jgnop\\s*)[0-9a-f]+ <([^\+]*)>\$";
 	$mcount_adjust = 0;
     }
     $alignment = 8;
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/selinux/install_policy.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/selinux/install_policy.sh
@@ -6,27 +6,24 @@
 	exit 1
 fi
 
-SF=`which setfiles`
-if [ $? -eq 1 ]; then
+SF=`which setfiles` || {
 	echo "Could not find setfiles"
 	echo "Do you have policycoreutils installed?"
 	exit 1
-fi
+}
 
-CP=`which checkpolicy`
-if [ $? -eq 1 ]; then
+CP=`which checkpolicy` || {
 	echo "Could not find checkpolicy"
 	echo "Do you have checkpolicy installed?"
 	exit 1
-fi
+}
 VERS=`$CP -V | awk '{print $1}'`
 
-ENABLED=`which selinuxenabled`
-if [ $? -eq 1 ]; then
+ENABLED=`which selinuxenabled` || {
 	echo "Could not find selinuxenabled"
 	echo "Do you have libselinux-utils installed?"
 	exit 1
-fi
+}
 
 if selinuxenabled; then
     echo "SELinux is already enabled"
@@ -78,7 +75,7 @@
 $SF -F file_contexts /
 
 mounts=`cat /proc/$$/mounts | \
-	egrep "ext[234]|jfs|xfs|reiserfs|jffs2|gfs2|btrfs|f2fs|ocfs2" | \
+	grep -E "ext[234]|jfs|xfs|reiserfs|jffs2|gfs2|btrfs|f2fs|ocfs2" | \
 	awk '{ print $2 '}`
 $SF -F file_contexts $mounts
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/sign-file.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/sign-file.c
@@ -30,6 +30,13 @@
 #include <openssl/engine.h>
 
 /*
+ * OpenSSL 3.0 deprecates the OpenSSL's ENGINE API.
+ *
+ * Remove this if/when that API is no longer used
+ */
+#pragma GCC diagnostic ignored "-Wdeprecated-declarations"
+
+/*
  * Use CMS if we have openssl-1.0.0 or newer available - otherwise we have to
  * assume that it's not available and its header file is missing and that we
  * should use PKCS#7 instead.  Switching to the older PKCS#7 format restricts
@@ -315,7 +322,7 @@
 				     CMS_NOSMIMECAP | use_keyid |
 				     use_signed_attrs),
 		    "CMS_add1_signer");
-		ERR(CMS_final(cms, bm, NULL, CMS_NOCERTS | CMS_BINARY) < 0,
+		ERR(CMS_final(cms, bm, NULL, CMS_NOCERTS | CMS_BINARY) != 1,
 		    "CMS_final");
 
 #else
@@ -334,10 +341,10 @@
 			b = BIO_new_file(sig_file_name, "wb");
 			ERR(!b, "%s", sig_file_name);
 #ifndef USE_PKCS7
-			ERR(i2d_CMS_bio_stream(b, cms, NULL, 0) < 0,
+			ERR(i2d_CMS_bio_stream(b, cms, NULL, 0) != 1,
 			    "%s", sig_file_name);
 #else
-			ERR(i2d_PKCS7_bio(b, pkcs7) < 0,
+			ERR(i2d_PKCS7_bio(b, pkcs7) != 1,
 			    "%s", sig_file_name);
 #endif
 			BIO_free(b);
@@ -367,9 +374,9 @@
 
 	if (!raw_sig) {
 #ifndef USE_PKCS7
-		ERR(i2d_CMS_bio_stream(bd, cms, NULL, 0) < 0, "%s", dest_name);
+		ERR(i2d_CMS_bio_stream(bd, cms, NULL, 0) != 1, "%s", dest_name);
 #else
-		ERR(i2d_PKCS7_bio(bd, pkcs7) < 0, "%s", dest_name);
+		ERR(i2d_PKCS7_bio(bd, pkcs7) != 1, "%s", dest_name);
 #endif
 	} else {
 		BIO *b;
@@ -389,7 +396,7 @@
 	ERR(BIO_write(bd, &sig_info, sizeof(sig_info)) < 0, "%s", dest_name);
 	ERR(BIO_write(bd, magic_number, sizeof(magic_number) - 1) < 0, "%s", dest_name);
 
-	ERR(BIO_free(bd) < 0, "%s", dest_name);
+	ERR(BIO_free(bd) != 1, "%s", dest_name);
 
 	/* Finally, if we're signing in place, replace the original. */
 	if (replace_orig)
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/sorttable.c
+++ linux-xilinx-zynqmp-5.15.0/scripts/sorttable.c
@@ -240,7 +240,7 @@
 
 		w(r(loc) + i, loc);
 		w(r(loc + 1) + i + 4, loc + 1);
-		w(r(loc + 2) + i + 8, loc + 2);
+		/* Don't touch the fixup type */
 
 		i += sizeof(uint32_t) * 3;
 	}
@@ -253,7 +253,7 @@
 
 		w(r(loc) - i, loc);
 		w(r(loc + 1) - (i + 4), loc + 1);
-		w(r(loc + 2) - (i + 8), loc + 2);
+		/* Don't touch the fixup type */
 
 		i += sizeof(uint32_t) * 3;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/sorttable.h
+++ linux-xilinx-zynqmp-5.15.0/scripts/sorttable.h
@@ -103,7 +103,7 @@
 
 static int orc_sort_cmp(const void *_a, const void *_b)
 {
-	struct orc_entry *orc_a;
+	struct orc_entry *orc_a, *orc_b;
 	const int *a = g_orc_ip_table + *(int *)_a;
 	const int *b = g_orc_ip_table + *(int *)_b;
 	unsigned long a_val = orc_ip(a);
@@ -121,6 +121,10 @@
 	 * whitelisted .o files which didn't get objtool generation.
 	 */
 	orc_a = g_orc_table + (a - g_orc_ip_table);
+	orc_b = g_orc_table + (b - g_orc_ip_table);
+	if (orc_a->sp_reg == ORC_REG_UNDEFINED && !orc_a->end &&
+	    orc_b->sp_reg == ORC_REG_UNDEFINED && !orc_b->end)
+		return 0;
 	return orc_a->sp_reg == ORC_REG_UNDEFINED && !orc_a->end ? -1 : 1;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/sphinx-pre-install
+++ linux-xilinx-zynqmp-5.15.0/scripts/sphinx-pre-install
@@ -78,6 +78,7 @@
 	'ucs.sty'            => 'texlive-ucs',
 	'upquote.sty'        => 'texlive-upquote',
 	'wrapfig.sty'        => 'texlive-wrapfig',
+	'ctexhook.sty'       => 'texlive-ctex',
 );
 
 #
@@ -369,6 +370,9 @@
 	);
 
 	if ($pdf) {
+		check_missing_file(["/usr/share/texlive/texmf-dist/tex/latex/ctex/ctexhook.sty"],
+				   "texlive-lang-chinese", 2);
+
 		check_missing_file(["/usr/share/fonts/truetype/dejavu/DejaVuSans.ttf"],
 				   "fonts-dejavu", 2);
 
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/tags.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/tags.sh
@@ -32,6 +32,13 @@
 	ignore="$ignore ( -path ${tree}tools ) -prune -o"
 fi
 
+# gtags(1) refuses to index any file outside of its current working dir.
+# If gtags indexing is requested and the build output directory is not
+# the kernel source tree, index all files in absolute-path form.
+if [[ "$1" == "gtags" && -n "${tree}" ]]; then
+	tree=$(realpath "$tree")/
+fi
+
 # Detect if ALLSOURCE_ARCHS is set. If not, we assume SRCARCH
 if [ "${ALLSOURCE_ARCHS}" = "" ]; then
 	ALLSOURCE_ARCHS=${SRCARCH}
@@ -95,10 +102,13 @@
 
 all_compiled_sources()
 {
-	realpath -es $([ -z "$KBUILD_ABS_SRCTREE" ] && echo --relative-to=.) \
-		include/generated/autoconf.h $(find $ignore -name "*.cmd" -exec \
-		grep -Poh '(?(?=^source_.* \K).*|(?=^  \K\S).*(?= \\))' {} \+ |
-		awk '!a[$0]++') | sort -u
+	{
+		echo include/generated/autoconf.h
+		find $ignore -name "*.cmd" -exec \
+			sed -n -E 's/^source_.* (.*)/\1/p; s/^  (\S.*) \\/\1/p' {} \+ |
+		awk '!a[$0]++'
+	} | xargs realpath -es $([ -z "$KBUILD_ABS_SRCTREE" ] && echo --relative-to=.) |
+	sort -u
 }
 
 all_target_sources()
@@ -128,7 +138,7 @@
 
 dogtags()
 {
-	all_target_sources | gtags -i -f -
+	all_target_sources | gtags -i -C "${tree:-.}" -f - "$PWD"
 }
 
 # Basic regular expressions with an optional /kind-spec/ for ctags and
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/tracing/ftrace-bisect.sh
+++ linux-xilinx-zynqmp-5.15.0/scripts/tracing/ftrace-bisect.sh
@@ -12,7 +12,7 @@
 #   (note, if this is a problem with function_graph tracing, then simply
 #    replace "function" with "function_graph" in the following steps).
 #
-#  # cd /sys/kernel/debug/tracing
+#  # cd /sys/kernel/tracing
 #  # echo schedule > set_ftrace_filter
 #  # echo function > current_tracer
 #
@@ -20,22 +20,40 @@
 #
 #  # echo nop > current_tracer
 #
-#  # cat available_filter_functions > ~/full-file
+# Starting with v5.1 this can be done with numbers, making it much faster:
+#
+# The old (slow) way, for kernels before v5.1.
+#
+# [old-way] # cat available_filter_functions > ~/full-file
+#
+# [old-way] *** Note ***  this process will take several minutes to update the
+# [old-way] filters. Setting multiple functions is an O(n^2) operation, and we
+# [old-way] are dealing with thousands of functions. So go have coffee, talk
+# [old-way] with your coworkers, read facebook. And eventually, this operation
+# [old-way] will end.
+#
+# The new way (using numbers) is an O(n) operation, and usually takes less than a second.
+#
+# seq `wc -l available_filter_functions | cut -d' ' -f1` > ~/full-file
+#
+# This will create a sequence of numbers that match the functions in
+# available_filter_functions, and when echoing in a number into the
+# set_ftrace_filter file, it will enable the corresponding function in
+# O(1) time. Making enabling all functions O(n) where n is the number of
+# functions to enable.
+#
+# For either the new or old way, the rest of the operations remain the same.
+#
 #  # ftrace-bisect ~/full-file ~/test-file ~/non-test-file
 #  # cat ~/test-file > set_ftrace_filter
 #
-# *** Note *** this will take several minutes. Setting multiple functions is
-# an O(n^2) operation, and we are dealing with thousands of functions. So go
-# have  coffee, talk with your coworkers, read facebook. And eventually, this
-# operation will end.
-#
 #  # echo function > current_tracer
 #
 # If it crashes, we know that ~/test-file has a bad function.
 #
 #   Reboot back to test kernel.
 #
-#     # cd /sys/kernel/debug/tracing
+#     # cd /sys/kernel/tracing
 #     # mv ~/test-file ~/full-file
 #
 # If it didn't crash.
--- linux-xilinx-zynqmp-5.15.0.orig/scripts/ubuntu-retpoline-extract-one
+++ linux-xilinx-zynqmp-5.15.0/scripts/ubuntu-retpoline-extract-one
@@ -0,0 +1,270 @@
+#!/bin/bash
+
+exec </dev/null
+
+object="$1"
+src="$2"
+bit16="$3"
+
+SECTION=".discard.retpoline_safe"
+
+# Form an associative lookup for the symbol numbers in the ELF symbol table.
+# Uses 8 character 0 expanded hexadecimal key for ease of consumption.
+__symbolmap_init()
+{
+	readelf -W --syms "$1" |
+		awk '($4 == "SECTION" && $1 ~ /^[0-9]*:/) { printf("%08x %08x\n", int($1), int($7)); }' | \
+	while read symbol_num section_num
+	do
+		echo "symbolmap_$symbol_num='$section_num'"
+	done
+}
+symbolmap_init()
+{
+	eval $(__symbolmap_init "$1")
+}
+symbolmap()
+{
+	eval RET="\$symbolmap_$1"
+	if [ "$RET" = '' ]; then
+		echo "symbolmap: $1: invalid section" 1>&2
+		exit 1
+	fi
+}
+
+# Form an associative lookup for the section numbers in the ELF symbol table.
+# Uses 8 character 0 expanded hexadecimal key for ease of consumption.
+__sectionmap_init()
+{
+	readelf -W --headers "$1" | \
+		awk '
+						{ sub("\\[", ""); sub("\\]", ""); }
+                        ($1 ~ /^[0-9][0-9]*/)   { printf("%08x %s %s %s\n", int($1), $2, $3, $4); }
+		' | \
+	{
+		while read section_num section_name section_type section_vma
+		do
+			echo "sectionmap_$section_num='$section_name'"
+			echo "sectionvma_$section_num='$section_vma'"
+			case "$section_type" in
+			REL|RELA) section_relocation="$section_type" ;;
+			esac
+		done
+		echo "section_relocation='$section_relocation'"
+	}
+}
+sectionmap_init()
+{
+	eval $(__sectionmap_init "$1")
+}
+sectionmap()
+{
+	eval RET="\$sectionmap_$1"
+	if [ "$RET" = '' ]; then
+		echo "sectionmap: $1: invalid section" 1>&2
+		exit 1
+	fi
+}
+sectionvma()
+{
+	eval RET="\$sectionvma_$1"
+	if [ "$RET" = '' ]; then
+		echo "sectionvma: $1: invalid section" 1>&2
+		exit 1
+	fi
+}
+
+# Read and parse the hex-dump output.
+hex="[0-9a-f]"
+hex_8="$hex$hex$hex$hex$hex$hex$hex$hex"
+hexspc="[0-9a-f ]"
+hexspc_8="$hexspc$hexspc$hexspc$hexspc$hexspc$hexspc$hexspc$hexspc"
+
+raw32()
+{
+	readelf --hex-dump "$2" "$1" 2>/dev/null |
+	sed \
+		-e '/^Hex/d' -e '/^$/d' -e '/^ *NOTE/d' \
+		-e 's/  *[^ ][^ ]*  *\('"$hex_8"'\) \('"$hexspc_8"'\) \('"$hexspc_8"'\) \('"$hexspc_8"'\) .*/\1 \2 \3 \4 /' \
+		-e 's/\('"$hex$hex"'\)\('"$hex$hex"'\)\('"$hex$hex"'\)\('"$hex$hex"'\) /\4\3\2\1 /g' \
+		-e 's/ $//g' -e 's/ /\n/g'
+}
+#-e 's/\([^ ][^ ][^ ][^ ][^ ][^ ][^ ][^ ]\) \([^ ][^ ][^ ][^ ][^ ][^ ][^ ][^ ]\) /\2\1 /g' \
+
+rela()
+{
+	#file="$(basename "$1")"
+	file="$1"
+
+	# Read relocation information for a 64bit binary.  Each relocation entry
+	# is 3 long longs so we collect 6 quads here.  Note that the dump is in
+	# listed in increasing byte order not withstanding the quad split.
+	#
+	# The record says to take the value of <symbol> add <symbol offset> and
+	# shove that into <write offset> in the segment of the <symbol>.
+	#
+	# Format:
+	#  <write offset>	64 bits
+	#  <symbol number>	32 bits
+	#  <relocation type>	32 bits
+	#  <symbol offset>	64 bits
+	raw32 "$1" ".rela$SECTION" | \
+	{
+		a1=''; a2=''; a3=''; a4=''; a5=''
+		while read a6
+		do
+			[ "$a1" = '' ] && { a1="$a6"; continue; }
+			[ "$a2" = '' ] && { a2="$a6"; continue; }
+			[ "$a3" = '' ] && { a3="$a6"; continue; }
+			[ "$a4" = '' ] && { a4="$a6"; continue; }
+			[ "$a5" = '' ] && { a5="$a6"; continue; }
+
+			#echo ">$a1< >$a2< >$a3< >$a4< >$a5< >$a6<" 1>&2
+			#echo "type<$a3> symbol<$a4> offset<$a2$a1> addr<$a6a5>" 1>&2
+
+			symbolmap "$a4"; section_num="$RET"
+			#echo "section_num<$section_num>" 1>&2
+
+			sectionmap "$section_num"; section="$RET"
+			sectionvma "$section_num"; vma="$RET"
+			#echo "section<$section> vma<$vma>" 1>&2
+
+			# Adjust the segment addressing by the segment offset.
+			printf -v addr "%u" "0x$a6$a5"
+			printf -v vma "%u" "0x$vma"
+			let offset="$addr + $vma"
+			printf -v offset "%x" "$offset"
+
+			echo "$file-$section-$offset"
+
+			a1=''; a2=''; a3=''; a4=''; a5=''
+		done
+	} | sed -e 's/-00*\([0-9a-f]\)/-\1/'
+}
+
+# Form an associative lookup for the raw contents for an ELF section.
+# Uses 8 character 0 expanded hexadecimal key for ease of consumption.
+contentmap_init()
+{
+	raw32 "$1" "$2" >"$tmp"
+	let offset=0
+	while read value
+	do
+		printf -v offset_hex "%08x" $offset
+		eval contentmap_$offset_hex=\'$value\'
+
+		let offset="$offset + 4"
+	done <"$tmp"
+	rm -f "$tmp"
+}
+contentmap()
+{
+	eval RET="\$contentmap_$1"
+	if [ "$RET" = '' ]; then
+		echo "contentmap: $1: invalid offset" 1>&2
+		exit 1
+	fi
+}
+
+rel()
+{
+	# Load up the current contents of the $SECTION segment
+	# as the offsets (see below) are recorded there and we will need
+	# those to calculate the actuall address.
+	contentmap_init "$1" "$SECTION"
+
+	#file="$(basename "$1")"
+	file="$1"
+
+	# Read relocation information for a 32bit binary.  Each relocation entry
+	# is 3 longs so we collect 3 quads here.  Note that the dump is in
+	# listed in increasing byte order not withstanding the quad split.
+	#
+	# The record says to take the value of <symbol> and add that to the
+	# existing contents of <write offset> in the segment of the <symbol>.
+	#
+	# Format:
+	#  <write offset>	32 bits
+	#  <symbol number>	24 bits
+	#  <relocation type>	 8 bits
+	raw32 "$1" ".rel$SECTION" | \
+	{
+		a1=''
+		while read a2
+		do
+			[ "$a1" = '' ] && { a1="$a2"; continue; }
+
+			#echo ">$a1< >$a2<"
+			contentmap "$a1"; offset="$RET"
+			symbolmap "00${a2%??}"; section_num="$RET"
+
+			sectionmap "$section_num"; section="$RET"
+			sectionvma "$section_num"; vma="$RET"
+			#echo ">$a1< >$a2< >$offset< >$section<"
+
+			echo "$file-$section-$offset"
+
+			a1=''
+		done
+	} | sed -e 's/-00*\([0-9a-f]\)/-\1/'
+}
+
+tmp=$(mktemp --tmpdir "retpoline-extract-XXXXXX")
+
+disassemble()
+{
+	local object="$1"
+	local src="$2"
+	local options="$3"
+	local selector="$4"
+
+	objdump $options --disassemble --no-show-raw-insn "$object" | \
+	awk -F' ' '
+		BEGIN				{ file="'"$object"'"; src="'"$src"'"; }
+		/Disassembly of section/        { segment=$4; sub(":", "", segment); }
+		/^[0-9a-f][0-9a-f]* <.*>:/      { tag=$0; sub(".*<", "", tag); sub(">.*", "", tag); }
+		$0 ~ /(call|jmp)q?  *\*0x[0-9a-f]*\(%rip\)/ {
+			next
+		}
+		$0 ~ /(call|jmp)q?  *\*.*%/ {
+			sub(":", "", $1);
+			if ('"$selector"') {
+				offset=$1
+				$1=tag
+				print(file "-" segment "-" offset " " src " " segment " " $0);
+			}
+		}
+	'
+}
+
+# Accumulate potentially vunerable indirect call/jmp sequences.  We do this
+# by examining the raw disassembly for affected forms, recording the location
+# of each.
+case "$bit16" in
+'')	disassemble "$object" "$src" '' 'segment != ".init.text"' ;;
+*)	disassemble "$object" "$src" '--disassembler-options=i8086' 'segment != ".init.text" && segment != ".text32" && segment != ".text64"'
+	disassemble "$object" "$src" '--disassembler-options=i386' 'segment == ".text32"'
+	disassemble "$object" "$src" '--disassembler-options=x86-64' 'segment == ".text64"'
+	;;
+esac | sort -k 1b,1 >"$object.ur-detected"
+[ ! -s "$object.ur-detected" ] && rm -f "$object.ur-detected"
+
+# Load up the symbol table and section mappings.
+symbolmap_init "$object"
+sectionmap_init "$object"
+
+# Accumulate annotated safe indirect call/jmp sequences.  We do this by examining
+# the $SECTION sections (and their associated relocation information),
+# each entry represents the address of an instruction which has been marked
+# as ok.
+case "$section_relocation" in
+REL)	rel "$object" ;;
+RELA)	rela "$object" ;;
+esac | sort -k 1b,1 >"$object.ur-safe"
+[ ! -s "$object.ur-safe" ] && rm -f "$object.ur-safe"
+
+# We will perform the below join on the summarised and sorted fragments
+# formed above.  This is performed in retpoline-check.
+#join -v 1 -j 1 "$tmp.extracted" "$tmp.safe" | sed -s 's/[^ ]*  *//'
+
+rm -f "$tmp"
--- linux-xilinx-zynqmp-5.15.0.orig/security/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/security/Kconfig
@@ -19,6 +19,47 @@
 
 	  If you are unsure how to answer this question, answer N.
 
+config SECURITY_PERF_EVENTS_RESTRICT
+	bool "Restrict unprivileged use of performance events"
+	depends on PERF_EVENTS
+	help
+	  If you say Y here, the kernel.perf_event_paranoid sysctl
+	  will be set to 3 by default, and no unprivileged use of the
+	  perf_event_open syscall will be permitted unless it is
+	  changed.
+
+choice
+	prompt "Allow /proc/pid/mem access override"
+	default PROC_MEM_ALWAYS_FORCE
+	help
+	  Traditionally /proc/pid/mem allows users to override memory
+	  permissions for users like ptrace, assuming they have ptrace
+	  capability.
+
+	  This allows people to limit that - either never override, or
+	  require actual active ptrace attachment.
+
+	  Defaults to the traditional behavior (for now)
+
+config PROC_MEM_ALWAYS_FORCE
+	bool "Traditional /proc/pid/mem behavior"
+	help
+	  This allows /proc/pid/mem accesses to override memory mapping
+	  permissions if you have ptrace access rights.
+
+config PROC_MEM_FORCE_PTRACE
+	bool "Require active ptrace() use for access override"
+	help
+	  This allows /proc/pid/mem accesses to override memory mapping
+	  permissions for active ptracers like gdb.
+
+config PROC_MEM_NO_FORCE
+	bool "Never"
+	help
+	  Never override memory mapping permissions
+
+endchoice
+
 config SECURITY
 	bool "Enable different security models"
 	depends on SYSFS
@@ -54,17 +95,6 @@
 	  implement socket and networking access controls.
 	  If you are unsure how to answer this question, answer N.
 
-config PAGE_TABLE_ISOLATION
-	bool "Remove the kernel mapping in user mode"
-	default y
-	depends on (X86_64 || X86_PAE) && !UML
-	help
-	  This feature reduces the number of hardware side channels by
-	  ensuring that the majority of kernel addresses are not mapped
-	  into userspace.
-
-	  See Documentation/x86/pti.rst for more details.
-
 config SECURITY_INFINIBAND
 	bool "Infiniband Security Hooks"
 	depends on SECURITY && INFINIBAND
@@ -191,6 +221,9 @@
 config FORTIFY_SOURCE
 	bool "Harden common str/mem functions against buffer overflows"
 	depends on ARCH_HAS_FORTIFY_SOURCE
+	# https://bugs.llvm.org/show_bug.cgi?id=50322
+	# https://bugs.llvm.org/show_bug.cgi?id=41459
+	depends on !CC_IS_CLANG
 	help
 	  Detect overflows of buffers in common string and memory functions
 	  where the compiler can determine and validate the buffer sizes.
--- linux-xilinx-zynqmp-5.15.0.orig/security/Kconfig.hardening
+++ linux-xilinx-zynqmp-5.15.0/security/Kconfig.hardening
@@ -22,14 +22,23 @@
 config CC_HAS_AUTO_VAR_INIT_PATTERN
 	def_bool $(cc-option,-ftrivial-auto-var-init=pattern)
 
-config CC_HAS_AUTO_VAR_INIT_ZERO
+config CC_HAS_AUTO_VAR_INIT_ZERO_BARE
+	def_bool $(cc-option,-ftrivial-auto-var-init=zero)
+
+config CC_HAS_AUTO_VAR_INIT_ZERO_ENABLER
+	# Clang 16 and later warn about using the -enable flag, but it
+	# is required before then.
 	def_bool $(cc-option,-ftrivial-auto-var-init=zero -enable-trivial-auto-var-init-zero-knowing-it-will-be-removed-from-clang)
+	depends on !CC_HAS_AUTO_VAR_INIT_ZERO_BARE
+
+config CC_HAS_AUTO_VAR_INIT_ZERO
+	def_bool CC_HAS_AUTO_VAR_INIT_ZERO_BARE || CC_HAS_AUTO_VAR_INIT_ZERO_ENABLER
 
 choice
 	prompt "Initialize kernel stack variables at function entry"
 	default GCC_PLUGIN_STRUCTLEAK_BYREF_ALL if COMPILE_TEST && GCC_PLUGINS
 	default INIT_STACK_ALL_PATTERN if COMPILE_TEST && CC_HAS_AUTO_VAR_INIT_PATTERN
-	default INIT_STACK_ALL_ZERO if CC_HAS_AUTO_VAR_INIT_PATTERN
+	default INIT_STACK_ALL_ZERO if CC_HAS_AUTO_VAR_INIT_ZERO
 	default INIT_STACK_NONE
 	help
 	  This option enables initialization of stack variables at
@@ -231,6 +240,9 @@
 
 config CC_HAS_ZERO_CALL_USED_REGS
 	def_bool $(cc-option,-fzero-call-used-regs=used-gpr)
+	# https://github.com/ClangBuiltLinux/linux/issues/1766
+	# https://github.com/llvm/llvm-project/issues/59242
+	depends on !CC_IS_CLANG || CLANG_VERSION > 150006
 
 config ZERO_CALL_USED_REGS
 	bool "Enable register zeroing on function exit"
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/Makefile
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/Makefile
@@ -5,7 +5,8 @@
 
 apparmor-y := apparmorfs.o audit.o capability.o task.o ipc.o lib.o match.o \
               path.o domain.o policy.o policy_unpack.o procattr.o lsm.o \
-              resource.o secid.o file.o policy_ns.o label.o mount.o net.o
+              resource.o secid.o file.o policy_ns.o label.o mount.o net.o \
+              af_unix.o
 apparmor-$(CONFIG_SECURITY_APPARMOR_HASH) += crypto.o
 
 clean-files := capability_names.h rlim_names.h net_names.h
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/af_unix.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/af_unix.c
@@ -0,0 +1,650 @@
+/*
+ * AppArmor security module
+ *
+ * This file contains AppArmor af_unix fine grained mediation
+ *
+ * Copyright 2018 Canonical Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2 of the
+ * License.
+ */
+
+#include <net/tcp_states.h>
+
+#include "include/audit.h"
+#include "include/af_unix.h"
+#include "include/apparmor.h"
+#include "include/file.h"
+#include "include/label.h"
+#include "include/path.h"
+#include "include/policy.h"
+#include "include/cred.h"
+
+static inline struct sock *aa_unix_sk(struct unix_sock *u)
+{
+	return &u->sk;
+}
+
+static inline int unix_fs_perm(const char *op, u32 mask, struct aa_label *label,
+			       struct unix_sock *u, int flags)
+{
+	AA_BUG(!label);
+	AA_BUG(!u);
+	AA_BUG(!UNIX_FS(aa_unix_sk(u)));
+
+	if (unconfined(label) || !LABEL_MEDIATES(label, AA_CLASS_FILE))
+		return 0;
+
+	mask &= NET_FS_PERMS;
+	if (!u->path.dentry) {
+		struct path_cond cond = { };
+		struct aa_perms perms = { };
+		struct aa_profile *profile;
+
+		/* socket path has been cleared because it is being shutdown
+		 * can only fall back to original sun_path request
+		 */
+		struct aa_sk_ctx *ctx = aa_sock(&u->sk);
+		if (ctx->path.dentry)
+			return aa_path_perm(op, label, &ctx->path, flags, mask,
+					    &cond);
+		return fn_for_each_confined(label, profile,
+			((flags | profile->path_flags) & PATH_MEDIATE_DELETED) ?
+				__aa_path_perm(op, profile,
+					       u->addr->name->sun_path, mask,
+					       &cond, flags, &perms) :
+				aa_audit_file(profile, &nullperms, op, mask,
+					      u->addr->name->sun_path, NULL,
+					      NULL, cond.uid,
+					      "Failed name lookup - "
+					      "deleted entry", -EACCES));
+	} else {
+		/* the sunpath may not be valid for this ns so use the path */
+		struct path_cond cond = { u->path.dentry->d_inode->i_uid,
+					  u->path.dentry->d_inode->i_mode
+		};
+
+		return aa_path_perm(op, label, &u->path, flags, mask, &cond);
+	}
+
+	return 0;
+}
+
+/* passing in state returned by PROFILE_MEDIATES_AF */
+static unsigned int match_to_prot(struct aa_profile *profile,
+				  unsigned int state, int type, int protocol,
+				  const char **info)
+{
+	__be16 buffer[2];
+	buffer[0] = cpu_to_be16(type);
+	buffer[1] = cpu_to_be16(protocol);
+	state = aa_dfa_match_len(profile->policy.dfa, state, (char *) &buffer,
+				 4);
+	if (!state)
+		*info = "failed type and protocol match";
+	return state;
+}
+
+static unsigned int match_addr(struct aa_profile *profile, unsigned int state,
+			       struct sockaddr_un *addr, int addrlen)
+{
+	if (addr)
+		/* include leading \0 */
+		state = aa_dfa_match_len(profile->policy.dfa, state,
+					 addr->sun_path,
+					 unix_addr_len(addrlen));
+	else
+		/* anonymous end point */
+		state = aa_dfa_match_len(profile->policy.dfa, state, "\x01",
+					 1);
+	/* todo change to out of band */
+	state = aa_dfa_null_transition(profile->policy.dfa, state);
+	return state;
+}
+
+static unsigned int match_to_local(struct aa_profile *profile,
+				   unsigned int state, int type, int protocol,
+				   struct sockaddr_un *addr, int addrlen,
+				   const char **info)
+{
+	state = match_to_prot(profile, state, type, protocol, info);
+	if (state) {
+		state = match_addr(profile, state, addr, addrlen);
+		if (state) {
+			/* todo: local label matching */
+			state = aa_dfa_null_transition(profile->policy.dfa,
+						       state);
+			if (!state)
+				*info = "failed local label match";
+		} else
+			*info = "failed local address match";
+	}
+
+	return state;
+}
+
+static unsigned int match_to_sk(struct aa_profile *profile,
+				unsigned int state, struct unix_sock *u,
+				const char **info)
+{
+	struct sockaddr_un *addr = NULL;
+	int addrlen = 0;
+
+	if (u->addr) {
+		addr = u->addr->name;
+		addrlen = u->addr->len;
+	}
+
+	return match_to_local(profile, state, u->sk.sk_type, u->sk.sk_protocol,
+			      addr, addrlen, info);
+}
+
+#define CMD_ADDR	1
+#define CMD_LISTEN	2
+#define CMD_OPT		4
+
+static inline unsigned int match_to_cmd(struct aa_profile *profile,
+					unsigned int state, struct unix_sock *u,
+					char cmd, const char **info)
+{
+	state = match_to_sk(profile, state, u, info);
+	if (state) {
+		state = aa_dfa_match_len(profile->policy.dfa, state, &cmd, 1);
+		if (!state)
+			*info = "failed cmd selection match";
+	}
+
+	return state;
+}
+
+static inline unsigned int match_to_peer(struct aa_profile *profile,
+					 unsigned int state,
+					 struct unix_sock *u,
+					 struct sockaddr_un *peer_addr,
+					 int peer_addrlen,
+					 const char **info)
+{
+	state = match_to_cmd(profile, state, u, CMD_ADDR, info);
+	if (state) {
+		state = match_addr(profile, state, peer_addr, peer_addrlen);
+		if (!state)
+			*info = "failed peer address match";
+	}
+	return state;
+}
+
+static int do_perms(struct aa_profile *profile, unsigned int state, u32 request,
+		    struct common_audit_data *sa)
+{
+	struct aa_perms perms;
+
+	AA_BUG(!profile);
+
+	aa_compute_perms(profile->policy.dfa, state, &perms);
+	aa_apply_modes_to_perms(profile, &perms);
+	return aa_check_perms(profile, &perms, request, sa,
+			      audit_net_cb);
+}
+
+static int match_label(struct aa_profile *profile, struct aa_profile *peer,
+			      unsigned int state, u32 request,
+			      struct common_audit_data *sa)
+{
+	AA_BUG(!profile);
+	AA_BUG(!peer);
+
+	aad(sa)->peer = &peer->label;
+
+	if (state) {
+		state = aa_dfa_match(profile->policy.dfa, state,
+				     peer->base.hname);
+		if (!state)
+			aad(sa)->info = "failed peer label match";
+	}
+	return do_perms(profile, state, request, sa);
+}
+
+
+/* unix sock creation comes before we know if the socket will be an fs
+ * socket
+ * v6 - semantics are handled by mapping in profile load
+ * v7 - semantics require sock create for tasks creating an fs socket.
+ */
+static int profile_create_perm(struct aa_profile *profile, int family,
+			       int type, int protocol)
+{
+	unsigned int state;
+	DEFINE_AUDIT_NET(sa, OP_CREATE, NULL, family, type, protocol);
+
+	AA_BUG(!profile);
+	AA_BUG(profile_unconfined(profile));
+
+	if ((state = PROFILE_MEDIATES_AF(profile, AF_UNIX))) {
+		state = match_to_prot(profile, state, type, protocol,
+				      &aad(&sa)->info);
+		return do_perms(profile, state, AA_MAY_CREATE, &sa);
+	}
+
+	return aa_profile_af_perm(profile, &sa, AA_MAY_CREATE, family, type);
+}
+
+int aa_unix_create_perm(struct aa_label *label, int family, int type,
+			int protocol)
+{
+	struct aa_profile *profile;
+
+	if (unconfined(label))
+		return 0;
+
+	return fn_for_each_confined(label, profile,
+			profile_create_perm(profile, family, type, protocol));
+}
+
+
+static inline int profile_sk_perm(struct aa_profile *profile, const char *op,
+				  u32 request, struct sock *sk)
+{
+	unsigned int state;
+	DEFINE_AUDIT_SK(sa, op, sk);
+
+	AA_BUG(!profile);
+	AA_BUG(!sk);
+	AA_BUG(UNIX_FS(sk));
+	AA_BUG(profile_unconfined(profile));
+
+	state = PROFILE_MEDIATES_AF(profile, AF_UNIX);
+	if (state) {
+		state = match_to_sk(profile, state, unix_sk(sk),
+				    &aad(&sa)->info);
+		return do_perms(profile, state, request, &sa);
+	}
+
+	return aa_profile_af_sk_perm(profile, &sa, request, sk);
+}
+
+int aa_unix_label_sk_perm(struct aa_label *label, const char *op, u32 request,
+			  struct sock *sk)
+{
+	struct aa_profile *profile;
+
+	return fn_for_each_confined(label, profile,
+			profile_sk_perm(profile, op, request, sk));
+}
+
+static int unix_label_sock_perm(struct aa_label *label, const char *op, u32 request,
+				struct socket *sock)
+{
+	if (unconfined(label))
+		return 0;
+	if (UNIX_FS(sock->sk))
+		return unix_fs_perm(op, request, label, unix_sk(sock->sk), 0);
+
+	return aa_unix_label_sk_perm(label, op, request, sock->sk);
+}
+
+/* revaliation, get/set attr */
+int aa_unix_sock_perm(const char *op, u32 request, struct socket *sock)
+{
+	struct aa_label *label;
+	int error;
+
+	label = begin_current_label_crit_section();
+	error = unix_label_sock_perm(label, op, request, sock);
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
+static int profile_bind_perm(struct aa_profile *profile, struct sock *sk,
+			     struct sockaddr *addr, int addrlen)
+{
+	unsigned int state;
+	DEFINE_AUDIT_SK(sa, OP_BIND, sk);
+
+	AA_BUG(!profile);
+	AA_BUG(!sk);
+	AA_BUG(addr->sa_family != AF_UNIX);
+	AA_BUG(profile_unconfined(profile));
+	AA_BUG(unix_addr_fs(addr, addrlen));
+
+	state = PROFILE_MEDIATES_AF(profile, AF_UNIX);
+	if (state) {
+		/* bind for abstract socket */
+		aad(&sa)->net.addr = unix_addr(addr);
+		aad(&sa)->net.addrlen = addrlen;
+
+		state = match_to_local(profile, state,
+				       sk->sk_type, sk->sk_protocol,
+				       unix_addr(addr), addrlen,
+				       &aad(&sa)->info);
+		return do_perms(profile, state, AA_MAY_BIND, &sa);
+	}
+
+	return aa_profile_af_sk_perm(profile, &sa, AA_MAY_BIND, sk);
+}
+
+int aa_unix_bind_perm(struct socket *sock, struct sockaddr *address,
+		      int addrlen)
+{
+	struct aa_profile *profile;
+	struct aa_label *label;
+	int error = 0;
+
+	 label = begin_current_label_crit_section();
+	 /* fs bind is handled by mknod */
+	if (!(unconfined(label) || unix_addr_fs(address, addrlen)))
+		error = fn_for_each_confined(label, profile,
+				profile_bind_perm(profile, sock->sk, address,
+						  addrlen));
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
+int aa_unix_connect_perm(struct socket *sock, struct sockaddr *address,
+			 int addrlen)
+{
+	/* unix connections are covered by the
+	 * - unix_stream_connect (stream) and unix_may_send hooks (dgram)
+	 * - fs connect is handled by open
+	 */
+	return 0;
+}
+
+static int profile_listen_perm(struct aa_profile *profile, struct sock *sk,
+			       int backlog)
+{
+	unsigned int state;
+	DEFINE_AUDIT_SK(sa, OP_LISTEN, sk);
+
+	AA_BUG(!profile);
+	AA_BUG(!sk);
+	AA_BUG(UNIX_FS(sk));
+	AA_BUG(profile_unconfined(profile));
+
+	state = PROFILE_MEDIATES_AF(profile, AF_UNIX);
+	if (state) {
+		__be16 b = cpu_to_be16(backlog);
+
+		state = match_to_cmd(profile, state, unix_sk(sk), CMD_LISTEN,
+				     &aad(&sa)->info);
+		if (state) {
+			state = aa_dfa_match_len(profile->policy.dfa, state,
+						 (char *) &b, 2);
+			if (!state)
+				aad(&sa)->info = "failed listen backlog match";
+		}
+		return do_perms(profile, state, AA_MAY_LISTEN, &sa);
+	}
+
+	return aa_profile_af_sk_perm(profile, &sa, AA_MAY_LISTEN, sk);
+}
+
+int aa_unix_listen_perm(struct socket *sock, int backlog)
+{
+	struct aa_profile *profile;
+	struct aa_label *label;
+	int error = 0;
+
+	label = begin_current_label_crit_section();
+	if (!(unconfined(label) || UNIX_FS(sock->sk)))
+		error = fn_for_each_confined(label, profile,
+				profile_listen_perm(profile, sock->sk,
+						    backlog));
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
+
+static inline int profile_accept_perm(struct aa_profile *profile,
+				      struct sock *sk,
+				      struct sock *newsk)
+{
+	unsigned int state;
+	DEFINE_AUDIT_SK(sa, OP_ACCEPT, sk);
+
+	AA_BUG(!profile);
+	AA_BUG(!sk);
+	AA_BUG(UNIX_FS(sk));
+	AA_BUG(profile_unconfined(profile));
+
+	state = PROFILE_MEDIATES_AF(profile, AF_UNIX);
+	if (state) {
+		state = match_to_sk(profile, state, unix_sk(sk),
+				    &aad(&sa)->info);
+		return do_perms(profile, state, AA_MAY_ACCEPT, &sa);
+	}
+
+	return aa_profile_af_sk_perm(profile, &sa, AA_MAY_ACCEPT, sk);
+}
+
+/* ability of sock to connect, not peer address binding */
+int aa_unix_accept_perm(struct socket *sock, struct socket *newsock)
+{
+	struct aa_profile *profile;
+	struct aa_label *label;
+	int error = 0;
+
+	label = begin_current_label_crit_section();
+	if (!(unconfined(label) || UNIX_FS(sock->sk)))
+		error = fn_for_each_confined(label, profile,
+				profile_accept_perm(profile, sock->sk,
+						    newsock->sk));
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
+
+/* dgram handled by unix_may_sendmsg, right to send on stream done at connect
+ * could do per msg unix_stream here
+ */
+/* sendmsg, recvmsg */
+int aa_unix_msg_perm(const char *op, u32 request, struct socket *sock,
+		     struct msghdr *msg, int size)
+{
+	return 0;
+}
+
+
+static int profile_opt_perm(struct aa_profile *profile, const char *op, u32 request,
+			    struct sock *sk, int level, int optname)
+{
+	unsigned int state;
+	DEFINE_AUDIT_SK(sa, op, sk);
+
+	AA_BUG(!profile);
+	AA_BUG(!sk);
+	AA_BUG(UNIX_FS(sk));
+	AA_BUG(profile_unconfined(profile));
+
+	state = PROFILE_MEDIATES_AF(profile, AF_UNIX);
+	if (state) {
+		__be16 b = cpu_to_be16(optname);
+
+		state = match_to_cmd(profile, state, unix_sk(sk), CMD_OPT,
+				     &aad(&sa)->info);
+		if (state) {
+			state = aa_dfa_match_len(profile->policy.dfa, state,
+						 (char *) &b, 2);
+			if (!state)
+				aad(&sa)->info = "failed sockopt match";
+		}
+		return do_perms(profile, state, request, &sa);
+	}
+
+	return aa_profile_af_sk_perm(profile, &sa, request, sk);
+}
+
+int aa_unix_opt_perm(const char *op, u32 request, struct socket *sock, int level,
+		     int optname)
+{
+	struct aa_profile *profile;
+	struct aa_label *label;
+	int error = 0;
+
+	label = begin_current_label_crit_section();
+	if (!(unconfined(label) || UNIX_FS(sock->sk)))
+		error = fn_for_each_confined(label, profile,
+				profile_opt_perm(profile, op, request,
+						 sock->sk, level, optname));
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
+/* null peer_label is allowed, in which case the peer_sk label is used */
+static int profile_peer_perm(struct aa_profile *profile, const char *op, u32 request,
+			     struct sock *sk, struct sock *peer_sk,
+			     struct aa_label *peer_label,
+			     struct common_audit_data *sa)
+{
+	unsigned int state;
+
+	AA_BUG(!profile);
+	AA_BUG(profile_unconfined(profile));
+	AA_BUG(!sk);
+	AA_BUG(!peer_sk);
+	AA_BUG(UNIX_FS(peer_sk));
+
+	state = PROFILE_MEDIATES_AF(profile, AF_UNIX);
+	if (state) {
+		struct aa_sk_ctx *peer_ctx = aa_sock(peer_sk);
+		struct aa_profile *peerp;
+		struct sockaddr_un *addr = NULL;
+		int len = 0;
+		if (unix_sk(peer_sk)->addr) {
+			addr = unix_sk(peer_sk)->addr->name;
+			len = unix_sk(peer_sk)->addr->len;
+		}
+		state = match_to_peer(profile, state, unix_sk(sk),
+				      addr, len, &aad(sa)->info);
+		if (!peer_label)
+			peer_label = peer_ctx->label;
+		return fn_for_each_in_ns(peer_label, peerp,
+				   match_label(profile, peerp, state, request,
+					       sa));
+	}
+
+	return aa_profile_af_sk_perm(profile, sa, request, sk);
+}
+
+/**
+ *
+ * Requires: lock held on both @sk and @peer_sk
+ */
+int aa_unix_peer_perm(struct aa_label *label, const char *op, u32 request,
+		      struct sock *sk, struct sock *peer_sk,
+		      struct aa_label *peer_label)
+{
+	struct unix_sock *peeru = unix_sk(peer_sk);
+	struct unix_sock *u = unix_sk(sk);
+
+	AA_BUG(!label);
+	AA_BUG(!sk);
+	AA_BUG(!peer_sk);
+
+	if (UNIX_FS(aa_unix_sk(peeru)))
+		return unix_fs_perm(op, request, label, peeru, 0);
+	else if (UNIX_FS(aa_unix_sk(u)))
+		return unix_fs_perm(op, request, label, u, 0);
+	else {
+		struct aa_profile *profile;
+		DEFINE_AUDIT_SK(sa, op, sk);
+		aad(&sa)->net.peer_sk = peer_sk;
+
+		/* TODO: ns!!! */
+		if (!net_eq(sock_net(sk), sock_net(peer_sk))) {
+			;
+		}
+
+		if (unconfined(label))
+			return 0;
+
+		return fn_for_each_confined(label, profile,
+				profile_peer_perm(profile, op, request, sk,
+						  peer_sk, peer_label, &sa));
+	}
+}
+
+
+/* from net/unix/af_unix.c */
+static void unix_state_double_lock(struct sock *sk1, struct sock *sk2)
+{
+	if (unlikely(sk1 == sk2) || !sk2) {
+		unix_state_lock(sk1);
+		return;
+	}
+	if (sk1 > sk2)
+		swap(sk1, sk2);
+
+	unix_state_lock(sk1);
+	unix_state_lock_nested(sk2, U_LOCK_SECOND);
+}
+
+static void unix_state_double_unlock(struct sock *sk1, struct sock *sk2)
+{
+	if (unlikely(sk1 == sk2) || !sk2) {
+		unix_state_unlock(sk1);
+		return;
+	}
+	unix_state_unlock(sk1);
+	unix_state_unlock(sk2);
+}
+
+int aa_unix_file_perm(struct aa_label *label, const char *op, u32 request,
+		      struct socket *sock)
+{
+	struct sock *peer_sk = NULL;
+	u32 sk_req = request & ~NET_PEER_MASK;
+	int error = 0;
+
+	AA_BUG(!label);
+	AA_BUG(!sock);
+	AA_BUG(!sock->sk);
+	AA_BUG(sock->sk->sk_family != AF_UNIX);
+
+	/* TODO: update sock label with new task label */
+	unix_state_lock(sock->sk);
+	peer_sk = unix_peer(sock->sk);
+	if (peer_sk)
+		sock_hold(peer_sk);
+	if (!unix_connected(sock) && sk_req) {
+		error = unix_label_sock_perm(label, op, sk_req, sock);
+		if (!error) {
+			// update label
+		}
+	}
+	unix_state_unlock(sock->sk);
+	if (!peer_sk)
+		return error;
+
+	unix_state_double_lock(sock->sk, peer_sk);
+	if (UNIX_FS(sock->sk)) {
+		error = unix_fs_perm(op, request, label, unix_sk(sock->sk),
+				     PATH_SOCK_COND);
+	} else if (UNIX_FS(peer_sk)) {
+		error = unix_fs_perm(op, request, label, unix_sk(peer_sk),
+				     PATH_SOCK_COND);
+	} else {
+		struct aa_sk_ctx *pctx = aa_sock(peer_sk);
+		if (sk_req)
+			error = aa_unix_label_sk_perm(label, op, sk_req,
+						      sock->sk);
+		last_error(error,
+			xcheck(aa_unix_peer_perm(label, op,
+						 MAY_READ | MAY_WRITE,
+						 sock->sk, peer_sk, NULL),
+			       aa_unix_peer_perm(pctx->label, op,
+						 MAY_READ | MAY_WRITE,
+						 peer_sk, sock->sk, label)));
+	}
+
+	unix_state_double_unlock(sock->sk, peer_sk);
+	sock_put(peer_sk);
+
+	return error;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/apparmorfs.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/apparmorfs.c
@@ -401,7 +401,7 @@
 
 	data->size = copy_size;
 	if (copy_from_user(data->data, userbuf, copy_size)) {
-		kvfree(data);
+		aa_put_loaddata(data);
 		return ERR_PTR(-EFAULT);
 	}
 
@@ -867,8 +867,10 @@
 	if (!t)
 		return ERR_PTR(-ENOMEM);
 	kref_init(&t->count);
-	if (copy_from_user(t->data, buf, size))
+	if (copy_from_user(t->data, buf, size)) {
+		put_multi_transaction(t);
 		return ERR_PTR(-EFAULT);
+	}
 
 	return t;
 }
@@ -1677,6 +1679,10 @@
 		struct aa_profile *p;
 		p = aa_deref_parent(profile);
 		dent = prof_dir(p);
+		if (!dent) {
+			error = -ENOENT;
+			goto fail2;
+		}
 		/* adding to parent that previously didn't have children */
 		dent = aafs_create_dir("profiles", dent);
 		if (IS_ERR(dent))
@@ -2291,6 +2297,12 @@
 	{ }
 };
 
+static struct aa_sfs_entry aa_sfs_entry_ipc[] = {
+	AA_SFS_FILE_STRING("posix_mqueue",
+			   "create read write open delete setattr getattr"),
+	{ }
+};
+
 static struct aa_sfs_entry aa_sfs_entry_ptrace[] = {
 	AA_SFS_FILE_STRING("mask", "read trace"),
 	{ }
@@ -2346,6 +2358,11 @@
 	{ }
 };
 
+static struct aa_sfs_entry aa_sfs_entry_dbus[] = {
+	AA_SFS_FILE_STRING("mask", "acquire send receive"),
+	{ }
+};
+
 static struct aa_sfs_entry aa_sfs_entry_query_label[] = {
 	AA_SFS_FILE_STRING("perms", "allow deny audit quiet"),
 	AA_SFS_FILE_BOOLEAN("data",		1),
@@ -2361,7 +2378,9 @@
 	AA_SFS_DIR("policy",			aa_sfs_entry_policy),
 	AA_SFS_DIR("domain",			aa_sfs_entry_domain),
 	AA_SFS_DIR("file",			aa_sfs_entry_file),
+	AA_SFS_DIR("ipc",			aa_sfs_entry_ipc),
 	AA_SFS_DIR("network_v8",		aa_sfs_entry_network),
+	AA_SFS_DIR("network",			aa_sfs_entry_network_compat),
 	AA_SFS_DIR("mount",			aa_sfs_entry_mount),
 	AA_SFS_DIR("namespaces",		aa_sfs_entry_ns),
 	AA_SFS_FILE_U64("capability",		VFS_CAP_FLAGS_MASK),
@@ -2369,6 +2388,7 @@
 	AA_SFS_DIR("caps",			aa_sfs_entry_caps),
 	AA_SFS_DIR("ptrace",			aa_sfs_entry_ptrace),
 	AA_SFS_DIR("signal",			aa_sfs_entry_signal),
+	AA_SFS_DIR("dbus",			aa_sfs_entry_dbus),
 	AA_SFS_DIR("query",			aa_sfs_entry_query),
 	{ }
 };
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/audit.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/audit.c
@@ -137,7 +137,7 @@
 	}
 	if (AUDIT_MODE(profile) == AUDIT_QUIET ||
 	    (type == AUDIT_APPARMOR_DENIED &&
-	     AUDIT_MODE(profile) == AUDIT_QUIET))
+	     AUDIT_MODE(profile) == AUDIT_QUIET_DENIED))
 		return aad(sa)->error;
 
 	if (KILL_MODE(profile) && type == AUDIT_APPARMOR_DENIED)
@@ -173,7 +173,7 @@
 	}
 }
 
-int aa_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule)
+int aa_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule, gfp_t gfp)
 {
 	struct aa_audit_rule *rule;
 
@@ -186,14 +186,14 @@
 		return -EINVAL;
 	}
 
-	rule = kzalloc(sizeof(struct aa_audit_rule), GFP_KERNEL);
+	rule = kzalloc(sizeof(struct aa_audit_rule), gfp);
 
 	if (!rule)
 		return -ENOMEM;
 
 	/* Currently rules are treated as coming from the root ns */
 	rule->label = aa_label_parse(&root_ns->unconfined->label, rulestr,
-				     GFP_KERNEL, true, false);
+				     gfp, true, false);
 	if (IS_ERR(rule->label)) {
 		int err = PTR_ERR(rule->label);
 		aa_audit_rule_free(rule);
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/capability.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/capability.c
@@ -94,6 +94,8 @@
 		return error;
 	} else {
 		aa_put_profile(ent->profile);
+		if (profile != ent->profile)
+			cap_clear(ent->caps);
 		ent->profile = aa_get_profile(profile);
 		cap_raise(ent->caps, cap);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/crypto.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/crypto.c
@@ -25,6 +25,25 @@
 	return apparmor_hash_size;
 }
 
+void aa_snprint_hashstr(char *out, unsigned char *hash, unsigned int hsize)
+{
+       unsigned int i;
+
+       for (i = 0; i < hsize; i++)
+               sprintf(out + i*2, "%.2x", hash[i]);
+       out[hsize*2] = 0;
+}
+
+char *aa_asprint_hashstr(unsigned char *hash, unsigned int hsize, gfp_t gfp)
+{
+	char *buffer = kmalloc(hsize*2 + 1, gfp);
+	if (!buffer)
+		return NULL;
+	aa_snprint_hashstr(buffer, hash, hsize);
+
+	return buffer;
+}
+
 char *aa_calc_hash(void *data, size_t len)
 {
 	SHASH_DESC_ON_STACK(desc, apparmor_tfm);
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/domain.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/domain.c
@@ -467,7 +467,7 @@
 				 * xattrs, or a longer match
 				 */
 				candidate = profile;
-				candidate_len = profile->xmatch_len;
+				candidate_len = max(count, profile->xmatch_len);
 				candidate_xattrs = ret;
 				conflict = false;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/file.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/file.c
@@ -14,10 +14,12 @@
 #include <linux/fs.h>
 #include <linux/mount.h>
 
+#include "include/af_unix.h"
 #include "include/apparmor.h"
 #include "include/audit.h"
 #include "include/cred.h"
 #include "include/file.h"
+#include "include/ipc.h"
 #include "include/match.h"
 #include "include/net.h"
 #include "include/path.h"
@@ -271,7 +273,8 @@
 {
 	int e = 0;
 
-	if (profile_unconfined(profile))
+	if (profile_unconfined(profile) ||
+	    ((flags & PATH_SOCK_COND) && !PROFILE_MEDIATES_AF(profile, AF_UNIX)))
 		return 0;
 	aa_str_perms(profile->file.dfa, profile->file.start, name, cond, perms);
 	if (request & ~perms->allow)
@@ -585,6 +588,60 @@
 	return error;
 }
 
+/* TODO: combine with __file_path_perm */
+static int __file_mqueue_perm(const char *op, struct aa_label *label,
+			      struct aa_label *flabel, struct file *file,
+			      u32 request, u32 denied, bool in_atomic)
+{
+	struct aa_profile *profile;
+	char *buffer;
+	int error;
+	DEFINE_AUDIT_DATA(sa, LSM_AUDIT_DATA_NONE, op);
+
+	/* revalidation due to label out of date. No revocation at this time */
+	if (!denied && aa_label_is_subset(flabel, label))
+		/* TODO: check for revocation on stale profiles */
+		return 0;
+
+	buffer = aa_get_buffer(in_atomic);
+	if (!buffer)
+		return -ENOMEM;
+
+	aad(&sa)->request = request;
+	aad(&sa)->peer = NULL;
+	aad(&sa)->mq.ouid = file_inode(file)->i_uid;
+	aad(&sa)->mq.fsuid = current_fsuid();	/* mqueue uses fsuid() */
+
+	/* check every profile in task label not in current cache */
+	error = fn_for_each_not_in_set(flabel, label, profile,
+			aa_profile_mqueue_perm(profile, &file->f_path,
+					       request, buffer, &sa));
+	if (denied && !error) {
+		/*
+		 * check every profile in file label that was not tested
+		 * in the initial check above.
+		 *
+		 * TODO: cache full perms so this only happens because of
+		 * conditionals
+		 * TODO: don't audit here
+		 */
+		if (label == flabel)
+			error = fn_for_each(label, profile,
+				aa_profile_mqueue_perm(profile, &file->f_path,
+						       request, buffer, &sa));
+		else
+			error = fn_for_each_not_in_set(label, flabel, profile,
+				aa_profile_mqueue_perm(profile, &file->f_path,
+						       request, buffer, &sa));
+	}
+	if (!error)
+		update_file_ctx(file_ctx(file), label, request);
+
+	aa_put_buffer(buffer);
+
+	return error;
+}
+
 /**
  * aa_file_perm - do permission revalidation check & audit for @file
  * @op: operation being checked
@@ -630,7 +687,10 @@
 	rcu_read_unlock();
 	/* TODO: label cross check */
 
-	if (file->f_path.mnt && path_mediated_fs(file->f_path.dentry))
+	if (is_mqueue_inode(file_inode(file))) {
+		error = __file_mqueue_perm(op, label, flabel, file,
+					   request, denied, in_atomic);
+	} else if (file->f_path.mnt && path_mediated_fs(file->f_path.dentry))
 		error = __file_path_perm(op, label, flabel, file, request,
 					 denied, in_atomic);
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/af_unix.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/af_unix.h
@@ -0,0 +1,114 @@
+/*
+ * AppArmor security module
+ *
+ * This file contains AppArmor af_unix fine grained mediation
+ *
+ * Copyright 2014 Canonical Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2 of the
+ * License.
+ */
+#ifndef __AA_AF_UNIX_H
+
+#include <net/af_unix.h>
+
+#include "label.h"
+//#include "include/net.h"
+
+#define unix_addr_len(L) ((L) - sizeof(sa_family_t))
+#define unix_abstract_name_len(L) (unix_addr_len(L) - 1)
+#define unix_abstract_len(U) (unix_abstract_name_len((U)->addr->len))
+#define addr_unix_abstract_name(B) ((B)[0] == 0)
+#define addr_unix_anonymous(U) (addr_unix_len(U) <= 0)
+#define addr_unix_abstract(U) (!addr_unix_anonymous(U) && addr_unix_abstract_name((U)->addr))
+//#define unix_addr_fs(U) (!unix_addr_anonymous(U) && !unix_addr_abstract_name((U)->addr))
+
+#define unix_addr(A) ((struct sockaddr_un *)(A))
+#define unix_addr_anon(A, L) ((A) && unix_addr_len(L) <= 0)
+#define unix_addr_fs(A, L) (!unix_addr_anon(A, L) && !addr_unix_abstract_name(unix_addr(A)->sun_path))
+
+#define UNIX_ANONYMOUS(U) (!unix_sk(U)->addr)
+/* from net/unix/af_unix.c */
+#define UNIX_ABSTRACT(U) (!UNIX_ANONYMOUS(U) &&				\
+			  unix_sk(U)->addr->hash < UNIX_HASH_SIZE)
+#define UNIX_FS(U) (!UNIX_ANONYMOUS(U) && unix_sk(U)->addr->name->sun_path[0])
+#define unix_peer(sk) (unix_sk(sk)->peer)
+#define unix_connected(S) ((S)->state == SS_CONNECTED)
+
+static inline void print_unix_addr(struct sockaddr_un *A, int L)
+{
+	char *buf = (A) ? (char *) &(A)->sun_path : NULL;
+	int len = unix_addr_len(L);
+	if (!buf || len <= 0)
+		printk(" <anonymous>");
+	else if (buf[0])
+		printk(" %s", buf);
+	else
+		/* abstract name len includes leading \0 */
+		printk(" %d @%.*s", len - 1, len - 1, buf+1);
+};
+
+/*
+	printk("%s: %s: f %d, t %d, p %d", __FUNCTION__,		\
+	       #SK ,							\
+*/
+#define print_unix_sk(SK)						\
+do {									\
+	struct unix_sock *u = unix_sk(SK);				\
+	printk("%s: f %d, t %d, p %d",	#SK ,				\
+	       (SK)->sk_family, (SK)->sk_type, (SK)->sk_protocol);	\
+	if (u->addr)							\
+		print_unix_addr(u->addr->name, u->addr->len);		\
+	else								\
+		print_unix_addr(NULL, sizeof(sa_family_t));		\
+	/* printk("\n");*/						\
+} while (0)
+
+#define print_sk(SK)							\
+do {									\
+	if (!(SK)) {							\
+		printk("%s: %s is null\n", __FUNCTION__, #SK);		\
+	} else if ((SK)->sk_family == PF_UNIX) {			\
+		print_unix_sk(SK);					\
+		printk("\n");						\
+	} else {							\
+		printk("%s: %s: family %d\n", __FUNCTION__, #SK ,	\
+		       (SK)->sk_family);				\
+	}								\
+} while (0)
+
+#define print_sock_addr(U) \
+do {			       \
+	printk("%s:\n", __FUNCTION__);					\
+	printk("    sock %s:", sock_ctx && sock_ctx->label ? aa_label_printk(sock_ctx->label, GFP_ATOMIC); : "<null>"); print_sk(sock); \
+	printk("    other %s:", other_ctx && other_ctx->label ? aa_label_printk(other_ctx->label, GFP_ATOMIC); : "<null>"); print_sk(other); \
+	printk("    new %s", new_ctx && new_ctx->label ? aa_label_printk(new_ctx->label, GFP_ATOMIC); : "<null>"); print_sk(newsk); \
+} while (0)
+
+
+
+
+int aa_unix_peer_perm(struct aa_label *label, const char *op, u32 request,
+		      struct sock *sk, struct sock *peer_sk,
+		      struct aa_label *peer_label);
+int aa_unix_label_sk_perm(struct aa_label *label, const char *op, u32 request,
+			  struct sock *sk);
+int aa_unix_sock_perm(const char *op, u32 request, struct socket *sock);
+int aa_unix_create_perm(struct aa_label *label, int family, int type,
+			int protocol);
+int aa_unix_bind_perm(struct socket *sock, struct sockaddr *address,
+		      int addrlen);
+int aa_unix_connect_perm(struct socket *sock, struct sockaddr *address,
+			 int addrlen);
+int aa_unix_listen_perm(struct socket *sock, int backlog);
+int aa_unix_accept_perm(struct socket *sock, struct socket *newsock);
+int aa_unix_msg_perm(const char *op, u32 request, struct socket *sock,
+		     struct msghdr *msg, int size);
+int aa_unix_opt_perm(const char *op, u32 request, struct socket *sock, int level,
+		     int optname);
+int aa_unix_file_perm(struct aa_label *label, const char *op, u32 request,
+		      struct socket *sock);
+
+#endif /* __AA_AF_UNIX_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/apparmor.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/apparmor.h
@@ -20,7 +20,7 @@
 #define AA_CLASS_UNKNOWN	1
 #define AA_CLASS_FILE		2
 #define AA_CLASS_CAP		3
-#define AA_CLASS_DEPRECATED	4
+#define AA_CLASS_NET_COMPAT	4
 #define AA_CLASS_RLIMITS	5
 #define AA_CLASS_DOMAIN		6
 #define AA_CLASS_MOUNT		7
@@ -28,8 +28,15 @@
 #define AA_CLASS_SIGNAL		10
 #define AA_CLASS_NET		14
 #define AA_CLASS_LABEL		16
+#define AA_CLASS_POSIX_MQUEUE	17
+#define AA_CLASS_IO_URING	18
+#define AA_CLASS_MODULE		19
+#define AA_CLASS_DISPLAY_LSM	20
 
-#define AA_CLASS_LAST		AA_CLASS_LABEL
+#define AA_CLASS_X		31
+#define AA_CLASS_DBUS		32
+
+#define AA_CLASS_LAST		AA_CLASS_DBUS
 
 /* Control parameters settable through module/boot flags */
 extern enum audit_mode aa_g_audit;
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/audit.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/audit.h
@@ -136,6 +136,10 @@
 					void *addr;
 					int addrlen;
 				} net;
+				struct {
+					kuid_t fsuid;
+					kuid_t ouid;
+				} mq;
 			};
 		};
 		struct {
@@ -186,7 +190,7 @@
 }
 
 void aa_audit_rule_free(void *vrule);
-int aa_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule);
+int aa_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule, gfp_t gfp);
 int aa_audit_rule_known(struct audit_krule *rule);
 int aa_audit_rule_match(u32 sid, u32 field, u32 op, void *vrule);
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/crypto.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/crypto.h
@@ -14,6 +14,8 @@
 
 #ifdef CONFIG_SECURITY_APPARMOR_HASH
 unsigned int aa_hash_size(void);
+void aa_snprint_hashstr(char *out, unsigned char *hash, unsigned int hsize);
+char *aa_asprint_hashstr(unsigned char *hash, unsigned int hsize, gfp_t gfp);
 char *aa_calc_hash(void *data, size_t len);
 int aa_calc_profile_hash(struct aa_profile *profile, u32 version, void *start,
 			 size_t len);
@@ -32,6 +34,15 @@
 {
 	return 0;
 }
+
+void aa_snprint_hashstr(char *out, unsigned char *hash, unsigned int hsize)
+{
+}
+
+char *aa_asprint_hashstr(unsigned char *hash, unsigned int hsize, gfp_t gfp);
+{
+	return NULL;
+}
 #endif
 
 #endif /* __APPARMOR_CRYPTO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/inode.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/inode.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * AppArmor security module
+ *
+ * This file contains AppArmor file mediation function definitions.
+ *
+ * Copyright 2022 Canonical Ltd.
+ */
+
+#ifndef __AA_INODE_H
+#define __AA_INODE_H
+
+#include <linux/spinlock.h>
+
+#include "lib.h"
+
+struct aa_inode_sec {
+	struct inode *inode;	/* back pointer to inode object */
+	struct aa_label *label;
+	u16 sclass;		/* security class of this object */
+	bool initialized;	/* initialization flag */
+	spinlock_t lock;
+};
+
+struct aa_superblock_sec {
+	struct aa_label *label;
+};
+
+static inline struct aa_inode_sec *apparmor_inode(const struct inode *inode)
+{
+	if (unlikely(!inode->i_security))
+		return NULL;
+	return inode->i_security + apparmor_blob_sizes.lbs_inode;
+}
+
+static inline struct aa_superblock_sec *apparmor_superblock(
+					const struct super_block *sb)
+{
+	return sb->s_security + apparmor_blob_sizes.lbs_superblock;
+}
+
+#endif /* __AA_INODE_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/ipc.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/ipc.h
@@ -11,7 +11,10 @@
 #ifndef __AA_IPC_H
 #define __AA_IPC_H
 
+#include <linux/msg.h>
 #include <linux/sched.h>
+#include "inode.h"
+#include "perms.h"
 
 struct aa_profile;
 
@@ -33,4 +36,57 @@
 		  u32 request);
 int aa_may_signal(struct aa_label *sender, struct aa_label *target, int sig);
 
+#define AA_AUDIT_POSIX_MQUEUE_MASK (AA_MAY_WRITE | AA_MAY_READ |    \
+				    AA_MAY_CREATE | AA_MAY_DELETE | \
+				    AA_MAY_OPEN | AA_MAY_SETATTR |  \
+				    AA_MAY_GETATTR)
+
+
+struct aa_msg_sec {
+	struct aa_label *label;
+};
+
+struct aa_ipc_sec {
+	struct aa_label *label;
+};
+
+static inline struct aa_ipc_sec *apparmor_ipc(const struct kern_ipc_perm *ipc)
+{
+	return ipc->security + apparmor_blob_sizes.lbs_ipc;
+}
+
+static inline struct aa_msg_sec *apparmor_msg_msg(const struct msg_msg *msg_msg)
+{
+	return msg_msg->security + apparmor_blob_sizes.lbs_msg_msg;
+}
+
+
+static inline bool is_mqueue_sb(struct super_block *sb)
+{
+	if (!sb)
+		pr_warn("mqueue sb == NULL\n");
+	if (!sb && !sb->s_type->name)
+		pr_warn("mqueue sb name == NULL\n");
+	return sb && sb->s_type->name && strcmp(sb->s_type->name, "mqueue") == 0;
+}
+
+static inline bool is_mqueue_inode(struct inode *i)
+{
+	struct aa_inode_sec *isec;
+
+	if (!i)
+		return false;
+
+	isec = apparmor_inode(i);
+	return isec && isec->sclass == AA_CLASS_POSIX_MQUEUE;
+}
+
+int aa_profile_mqueue_perm(struct aa_profile *profile,
+			   const struct path *path,
+			   u32 request, char *buffer,
+			   struct common_audit_data *sa);
+
+int aa_mqueue_perm(const char *op, struct aa_label *label,
+		   const struct path *path, u32 request);
+
 #endif /* __AA_IPC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/lib.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/lib.h
@@ -22,6 +22,11 @@
  */
 
 #define DEBUG_ON (aa_g_debug)
+/*
+ * split individual debug cases out in preparation for finer grained
+ * debug controls in the future.
+ */
+#define AA_DEBUG_LABEL DEBUG_ON
 #define dbg_printk(__fmt, __args...) pr_debug(__fmt, ##__args)
 #define AA_DEBUG(fmt, args...)						\
 	do {								\
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/net.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/net.h
@@ -49,9 +49,14 @@
 struct aa_sk_ctx {
 	struct aa_label *label;
 	struct aa_label *peer;
+	struct path path;
 };
 
-#define SK_CTX(X) ((X)->sk_security)
+static inline struct aa_sk_ctx *aa_sock(const struct sock *sk)
+{
+	return sk->sk_security + apparmor_blob_sizes.lbs_sock;
+}
+
 #define SOCK_ctx(X) SOCK_INODE(X)->i_security
 #define DEFINE_AUDIT_NET(NAME, OP, SK, F, T, P)				  \
 	struct lsm_network_audit NAME ## _net = { .sk = (SK),		  \
@@ -68,11 +73,24 @@
 	DEFINE_AUDIT_NET(NAME, OP, SK, (SK)->sk_family, (SK)->sk_type,	\
 			 (SK)->sk_protocol)
 
+/* struct aa_net - network confinement data
+ * @allow: basic network families permissions
+ * @audit: which network permissions to force audit
+ * @quiet: which network permissions to quiet rejects
+ */
+struct aa_net_compat {
+	u16 allow[AF_MAX];
+	u16 audit[AF_MAX];
+	u16 quiet[AF_MAX];
+};
 
 #define af_select(FAMILY, FN, DEF_FN)		\
 ({						\
 	int __e;				\
 	switch ((FAMILY)) {			\
+	case AF_UNIX:				\
+		__e = aa_unix_ ## FN;		\
+		break;				\
 	default:				\
 		__e = DEF_FN;			\
 	}					\
@@ -87,6 +105,7 @@
 };
 
 extern struct aa_sfs_entry aa_sfs_entry_network[];
+extern struct aa_sfs_entry aa_sfs_entry_network_compat[];
 
 void audit_net_cb(struct audit_buffer *ab, void *va);
 int aa_profile_af_perm(struct aa_profile *profile, struct common_audit_data *sa,
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/path.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/path.h
@@ -13,6 +13,7 @@
 
 enum path_flags {
 	PATH_IS_DIR = 0x1,		/* path is a directory */
+	PATH_SOCK_COND = 0x2,
 	PATH_CONNECT_PATH = 0x4,	/* connect disconnected paths to / */
 	PATH_CHROOT_REL = 0x8,		/* do path lookup relative to chroot */
 	PATH_CHROOT_NSCONNECT = 0x10,	/* connect paths that are at ns root */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/perms.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/perms.h
@@ -137,6 +137,9 @@
 			 u32 mask);
 void aa_audit_perm_names(struct audit_buffer *ab, const char * const *names,
 			 u32 mask);
+void aa_audit_perms(struct audit_buffer *ab,  struct common_audit_data *sa,
+		    const char *chrs, u32 chrsmask, const char * const *names,
+		    u32 namesmask);
 void aa_audit_perm_mask(struct audit_buffer *ab, u32 mask, const char *chrs,
 			u32 chrsmask, const char * const *names, u32 namesmask);
 void aa_apply_modes_to_perms(struct aa_profile *profile,
@@ -150,6 +153,12 @@
 int aa_profile_label_perm(struct aa_profile *profile, struct aa_profile *target,
 			  u32 request, int type, u32 *deny,
 			  struct common_audit_data *sa);
+
+static inline u32 denied_perms(struct aa_perms *perms, u32 request)
+{
+	return request & (~perms->allow | perms->deny);
+}
+
 int aa_check_perms(struct aa_profile *profile, struct aa_perms *perms,
 		   u32 request, struct common_audit_data *sa,
 		   void (*cb)(struct audit_buffer *, void *));
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/policy.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/policy.h
@@ -108,6 +108,7 @@
  * @policy: general match rules governing policy
  * @file: The set of rules governing basic file access and domain transitions
  * @caps: capabilities for the profile
+ * @net_compat: v2 compat network controls for the profile
  * @rlimits: rlimits for the profile
  *
  * @dents: dentries for the profiles file entries in apparmorfs
@@ -135,7 +136,7 @@
 
 	const char *attach;
 	struct aa_dfa *xmatch;
-	int xmatch_len;
+	unsigned int xmatch_len;
 	enum audit_mode audit;
 	long mode;
 	u32 path_flags;
@@ -145,6 +146,7 @@
 	struct aa_policydb policy;
 	struct aa_file_rules file;
 	struct aa_caps caps;
+	struct aa_net_compat *net_compat;
 
 	int xattr_count;
 	char **xattrs;
@@ -228,9 +230,13 @@
 	unsigned int state = PROFILE_MEDIATES(profile, AA_CLASS_NET);
 	__be16 be_af = cpu_to_be16(AF);
 
-	if (!state)
-		return 0;
-	return aa_dfa_match_len(profile->policy.dfa, state, (char *) &be_af, 2);
+	if (!state) {
+		state = PROFILE_MEDIATES(profile, AA_CLASS_NET_COMPAT);
+		if (!state)
+			return 0;
+	}
+	state = aa_dfa_match_len(profile->policy.dfa, state, (char *) &be_af, 2);
+	return state;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/procattr.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/procattr.h
@@ -11,7 +11,7 @@
 #ifndef __AA_PROCATTR_H
 #define __AA_PROCATTR_H
 
-int aa_getprocattr(struct aa_label *label, char **string);
+int aa_getprocattr(struct aa_label *label, char **string, bool newline);
 int aa_setprocattr_changehat(char *args, size_t size, int flags);
 
 #endif /* __AA_PROCATTR_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/include/secid.h
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/include/secid.h
@@ -21,6 +21,9 @@
 /* secid value that matches any other secid */
 #define AA_SECID_WILDCARD 1
 
+/* sysctl to enable displaying mode when converting secid to secctx */
+extern int apparmor_display_secid_mode;
+
 struct aa_label *aa_secid_to_label(u32 secid);
 int apparmor_secid_to_secctx(u32 secid, char **secdata, u32 *seclen);
 int apparmor_secctx_to_secid(const char *secdata, u32 seclen, u32 *secid);
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/ipc.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/ipc.c
@@ -10,10 +10,13 @@
 
 #include <linux/gfp.h>
 #include <linux/ptrace.h>
+#include <linux/nsproxy.h>
+#include <linux/ipc_namespace.h>
 
 #include "include/audit.h"
 #include "include/capability.h"
 #include "include/cred.h"
+#include "include/path.h"
 #include "include/policy.h"
 #include "include/ipc.h"
 #include "include/sig_names.h"
@@ -216,3 +219,104 @@
 			profile_signal_perm(profile, target, MAY_WRITE, &sa),
 			profile_signal_perm(profile, sender, MAY_READ, &sa));
 }
+
+
+static void audit_mqueue_cb(struct audit_buffer *ab, void *va)
+{
+	struct common_audit_data *sa = va;
+
+	aa_audit_perms(ab, sa, NULL, 0, NULL, AA_AUDIT_POSIX_MQUEUE_MASK);
+
+	/* move class into generic audit framse work */
+	audit_log_format(ab, "class=\"posix_mqueue\"");
+	if (aad(sa)->request & AA_AUDIT_FILE_MASK) {
+		audit_log_format(ab, " fsuid=%u",
+				 from_kuid(&init_user_ns, aad(sa)->mq.fsuid));
+		audit_log_format(ab, " ouid=%u",
+				 from_kuid(&init_user_ns, aad(sa)->mq.ouid));
+	}
+	if (aad(sa)->peer) {
+		audit_log_format(ab, " olabel=");
+		aa_label_xaudit(ab, labels_ns(aad(sa)->label), aad(sa)->peer,
+				FLAGS_NONE, GFP_ATOMIC);
+	}
+}
+
+int aa_profile_mqueue_perm(struct aa_profile *profile, const struct path *path,
+			   u32 request, char *buffer,
+			   struct common_audit_data *sa)
+{
+	struct aa_perms perms = { };
+	unsigned int state;
+	char *name;
+
+	if (profile_unconfined(profile) ||
+	    !PROFILE_MEDIATES(profile, AA_CLASS_POSIX_MQUEUE))
+		return 0;
+
+	aad(sa)->label = &profile->label;
+
+	name = dentry_path_raw(path->dentry, buffer, aa_g_path_max);
+	if (IS_ERR(name))
+		return PTR_ERR(name);
+	if (path->mnt != current->nsproxy->ipc_ns->mq_mnt) {
+		/* TODO: disconnected path detection */
+		pr_warn("apparmor mqueue disconnected TODO\n");
+	}
+
+	aad(sa)->name = name;
+
+	state = aa_dfa_match(profile->policy.dfa,
+			     profile->policy.start[AA_CLASS_POSIX_MQUEUE],
+			     name);
+	aa_compute_perms(profile->policy.dfa, state, &perms);
+	aa_apply_modes_to_perms(profile, &perms);
+	if (!denied_perms(&perms, request)) {
+		/* early bailout sufficient perms no need to do further
+		 * checks */
+		return aa_check_perms(profile, &perms, request, sa,
+				      audit_mqueue_cb);
+	}
+	/* continue check to see if we have label perms */
+	//aa_label_match(profile, peer??, state false, request, &perms);
+	//aa_apply_modes_to_perms(profile, &perms);
+
+	// this will just cause failure without above label check
+	return aa_check_perms(profile, &perms, request, sa, audit_mqueue_cb);
+}
+
+/* mqueue - no label caching test */
+int aa_mqueue_perm(const char *op, struct aa_label *label,
+		   const struct path *path, u32 request)
+{
+	struct aa_profile *profile;
+	char *buffer;
+	int error;
+	DEFINE_AUDIT_DATA(sa, LSM_AUDIT_DATA_NONE, op);
+
+	// do we need delegate deleted with mqueues? probably
+	//flags |= PATH_DELEGATE_DELETED;
+
+	/* sadly due to rcu walk hairiness, we use dentry_path_raw instead
+	 *  of just accessing the name directly, which means we need to
+	 *  do the whole buffer allocation mess
+	 */
+	buffer = aa_get_buffer(false);
+	if (!buffer)
+		return -ENOMEM;
+
+	/* audit fields that won't change during iteration */
+	aad(&sa)->request = request;
+	aad(&sa)->peer = NULL;
+	aad(&sa)->mq.fsuid = current_fsuid();	/* mqueue uses fsuid() */
+	aad(&sa)->mq.ouid = d_backing_inode(path->dentry) ?
+					d_backing_inode(path->dentry)->i_uid:
+					current_fsuid();
+
+	error = fn_for_each_confined(label, profile,
+			aa_profile_mqueue_perm(profile, path, request,
+					       buffer, &sa));
+	aa_put_buffer(buffer);
+
+	return error;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/label.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/label.c
@@ -1454,7 +1454,7 @@
 	if (label->hname || labels_ns(label) != ns)
 		return res;
 
-	if (aa_label_acntsxprint(&name, ns, label, FLAGS_NONE, gfp) == -1)
+	if (aa_label_acntsxprint(&name, ns, label, FLAGS_NONE, gfp) < 0)
 		return res;
 
 	ls = labels_set(label);
@@ -1632,9 +1632,9 @@
 	AA_BUG(!str && size != 0);
 	AA_BUG(!label);
 
-	if (flags & FLAG_ABS_ROOT) {
+	if (AA_DEBUG_LABEL && (flags & FLAG_ABS_ROOT)) {
 		ns = root_ns;
-		len = snprintf(str, size, "=");
+		len = snprintf(str, size, "_");
 		update_for_len(total, len, size, str);
 	} else if (!ns) {
 		ns = labels_ns(label);
@@ -1704,7 +1704,7 @@
 
 /**
  * aa_label_acntsxprint - allocate a __counted string buffer and print label
- * @strp: buffer to write to. (MAY BE NULL if @size == 0)
+ * @strp: buffer to write to.
  * @ns: namespace profile is being viewed from
  * @label: label to view (NOT NULL)
  * @flags: flags controlling what label info is printed
@@ -1745,7 +1745,7 @@
 	if (!use_label_hname(ns, label, flags) ||
 	    display_mode(ns, label, flags)) {
 		len  = aa_label_asxprint(&name, ns, label, flags, gfp);
-		if (len == -1) {
+		if (len < 0) {
 			AA_DEBUG("label print error");
 			return;
 		}
@@ -1773,7 +1773,7 @@
 		int len;
 
 		len = aa_label_asxprint(&str, ns, label, flags, gfp);
-		if (len == -1) {
+		if (len < 0) {
 			AA_DEBUG("label print error");
 			return;
 		}
@@ -1796,7 +1796,7 @@
 		int len;
 
 		len = aa_label_asxprint(&str, ns, label, flags, gfp);
-		if (len == -1) {
+		if (len < 0) {
 			AA_DEBUG("label print error");
 			return;
 		}
@@ -1896,7 +1896,8 @@
 	AA_BUG(!str);
 
 	str = skipn_spaces(str, n);
-	if (str == NULL || (*str == '=' && base != &root_ns->unconfined->label))
+	if (str == NULL || (AA_DEBUG_LABEL && *str == '_' &&
+			    base != &root_ns->unconfined->label))
 		return ERR_PTR(-EINVAL);
 
 	len = label_count_strn_entries(str, end - str);
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/lib.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/lib.c
@@ -151,7 +151,7 @@
 
 
 const char aa_file_perm_chrs[] = "xwracd         km l     ";
-const char *aa_file_perm_names[] = {
+const char *aa_base_perm_names[] = {
 	"exec",
 	"write",
 	"read",
@@ -241,6 +241,10 @@
 {
 	char str[33];
 
+	if (!chrs)
+		chrs = aa_file_perm_chrs;
+	if (!names)
+		names = aa_base_perm_names;
 	audit_log_format(ab, "\"");
 	if ((mask & chrsmask) && chrs) {
 		aa_perm_mask_to_str(str, sizeof(str), chrs, mask & chrsmask);
@@ -254,6 +258,22 @@
 	audit_log_format(ab, "\"");
 }
 
+void aa_audit_perms(struct audit_buffer *ab, struct common_audit_data *sa,
+		    const char *chrs, u32 chrsmask, const char * const *names,
+		    u32 namesmask)
+{
+	if (aad(sa)->request) {
+		audit_log_format(ab, " requested=");
+		aa_audit_perm_mask(ab, aad(sa)->request, chrs, chrsmask,
+				   names, namesmask);
+	}
+	if (aad(sa)->denied) {
+		audit_log_format(ab, " denied=");
+		aa_audit_perm_mask(ab, aad(sa)->denied, chrs, chrsmask,
+				   names, namesmask);
+	}
+}
+
 /**
  * aa_audit_perms_cb - generic callback fn for auditing perms
  * @ab: audit buffer (NOT NULL)
@@ -263,18 +283,8 @@
 {
 	struct common_audit_data *sa = va;
 
-	if (aad(sa)->request) {
-		audit_log_format(ab, " requested_mask=");
-		aa_audit_perm_mask(ab, aad(sa)->request, aa_file_perm_chrs,
-				   PERMS_CHRS_MASK, aa_file_perm_names,
-				   PERMS_NAMES_MASK);
-	}
-	if (aad(sa)->denied) {
-		audit_log_format(ab, "denied_mask=");
-		aa_audit_perm_mask(ab, aad(sa)->denied, aa_file_perm_chrs,
-				   PERMS_CHRS_MASK, aa_file_perm_names,
-				   PERMS_NAMES_MASK);
-	}
+	aa_audit_perms(ab, sa, aa_file_perm_chrs, PERMS_CHRS_MASK,
+		       aa_base_perm_names, PERMS_NAMES_MASK);
 	audit_log_format(ab, " peer=");
 	aa_label_xaudit(ab, labels_ns(aad(sa)->label), aad(sa)->peer,
 				      FLAGS_NONE, GFP_ATOMIC);
@@ -334,7 +344,7 @@
 	/* for v5 perm mapping in the policydb, the other set is used
 	 * to extend the general perm set
 	 */
-	perms->allow |= map_other(dfa_other_allow(dfa, state));
+	perms->allow |= map_other(dfa_other_allow(dfa, state)) | AA_MAY_LOCK;
 	perms->audit |= map_other(dfa_other_audit(dfa, state));
 	perms->quiet |= map_other(dfa_other_quiet(dfa, state));
 //	perms->xindex = dfa_user_xindex(dfa, state);
@@ -431,7 +441,7 @@
 		   void (*cb)(struct audit_buffer *, void *))
 {
 	int type, error;
-	u32 denied = request & (~perms->allow | perms->deny);
+	u32 denied = denied_perms(perms, request);
 
 	if (likely(!denied)) {
 		/* mask off perms that are not being force audited */
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/lsm.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/lsm.c
@@ -18,6 +18,8 @@
 #include <linux/ctype.h>
 #include <linux/sysctl.h>
 #include <linux/audit.h>
+#include <linux/nsproxy.h>
+#include <linux/ipc_namespace.h>
 #include <linux/user_namespace.h>
 #include <linux/netfilter_ipv4.h>
 #include <linux/netfilter_ipv6.h>
@@ -25,12 +27,14 @@
 #include <net/sock.h>
 #include <uapi/linux/mount.h>
 
+#include "include/af_unix.h"
 #include "include/apparmor.h"
 #include "include/apparmorfs.h"
 #include "include/audit.h"
 #include "include/capability.h"
 #include "include/cred.h"
 #include "include/file.h"
+#include "include/inode.h"
 #include "include/ipc.h"
 #include "include/net.h"
 #include "include/path.h"
@@ -56,6 +60,11 @@
 static LIST_HEAD(aa_global_buffers);
 static DEFINE_SPINLOCK(aa_buffers_lock);
 
+static bool is_mqueue_dentry(struct dentry *dentry)
+{
+	return dentry && is_mqueue_inode(d_backing_inode(dentry));
+}
+
 /*
  * LSM hook functions
  */
@@ -399,11 +408,167 @@
 	return common_perm_cond(OP_CHOWN, path, AA_MAY_CHOWN);
 }
 
+static int common_mqueue_path_perm(const char *op, u32 request,
+				   const struct path *path)
+{
+	struct aa_label *label;
+	int error = 0;
+
+	label = begin_current_label_crit_section();
+	if (!unconfined(label))
+		error = aa_mqueue_perm(OP_UNLINK, label, path, request);
+
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
 static int apparmor_inode_getattr(const struct path *path)
 {
+	if (is_mqueue_dentry(path->dentry))
+		/* TODO: fn() for d_parent */
+		return common_mqueue_path_perm(OP_UNLINK, AA_MAY_GETATTR, path);
+
 	return common_perm_cond(OP_GETATTR, path, AA_MAY_GETATTR);
 }
 
+/* inode security operations */
+
+/* alloced by infrastructure */
+static int apparmor_inode_alloc_security(struct inode *inode)
+{
+	struct aa_inode_sec *isec = apparmor_inode(inode);
+
+	spin_lock_init(&isec->lock);
+	isec->inode = inode;
+	isec->label = NULL;
+	isec->sclass = 0;
+	isec->initialized = false;
+
+	return 0;
+}
+
+/* freed by infrastructure */
+static void apparmor_inode_free_security(struct inode *inode)
+{
+	struct aa_inode_sec *isec = apparmor_inode(inode);
+
+	if (!isec)
+		return;
+
+	aa_put_label(isec->label);
+}
+
+
+/* this is broken, in that we must make it work for ALL xattr fs
+ * or it will bail early, so this does not work with LSM stacking
+ */
+static int apparmor_inode_init_security(struct inode *inode, struct inode *dir,
+				       const struct qstr *qstr,
+				       const char **name,
+				       void **value, size_t *len)
+{
+	struct aa_inode_sec *isec = apparmor_inode(inode);
+
+	if (is_mqueue_inode(dir)) {
+		/* only initialize based on implied label atm */
+		isec->label = aa_get_current_label();
+		isec->sclass = AA_CLASS_POSIX_MQUEUE;
+		isec->initialized = true;
+	}
+
+	/* we aren't setting xattrs yet so pretend it isn't supported,
+	 * note bug in LSM means other LSMs won't get to init inode either
+	 */
+	return -EOPNOTSUPP;
+}
+
+static int inode_init_with_dentry(struct inode *inode, struct dentry *dentry)
+{
+	struct aa_inode_sec *isec = apparmor_inode(inode);
+
+	if (isec->initialized)
+		return 0;
+	spin_lock(&isec->lock);
+	/* recheck under lock */
+	if (isec->initialized)
+		goto unlock;
+
+	if (is_mqueue_sb(inode->i_sb)) {
+		/* only initialize based on implied label atm */
+		isec->label = aa_get_current_label();
+		isec->sclass = AA_CLASS_POSIX_MQUEUE;
+		isec->initialized = true;
+	}
+
+unlock:
+	spin_unlock(&isec->lock);
+
+	return 0;
+}
+
+static void apparmor_d_instantiate(struct dentry *dentry, struct inode *inode)
+{
+	if (inode)
+		inode_init_with_dentry(inode, dentry);
+}
+
+static int apparmor_inode_create(struct inode *dir, struct dentry *dentry,
+				 umode_t mode)
+{
+	struct aa_label *label;
+	int error = 0;
+
+	label = begin_current_label_crit_section();
+	if (!unconfined(label)) {
+		struct path path = {
+			.dentry = dentry,
+			.mnt = current->nsproxy->ipc_ns->mq_mnt,
+		};
+		if (is_mqueue_inode(dir)) {
+			error = aa_mqueue_perm(OP_CREATE, label, &path, AA_MAY_CREATE);
+		}
+	}
+	end_current_label_crit_section(label);
+
+	return error;
+}
+
+static int common_mqueue_perm(const char *op, u32 request, struct inode *dir, struct dentry *dentry)
+{
+	/* can't directly determine ipc ns, but know for mqueues dir is mnt_root */
+	struct path path = {
+		.dentry = dentry,
+		.mnt = d_inode(current->nsproxy->ipc_ns->mq_mnt->mnt_root) == dir ? current->nsproxy->ipc_ns->mq_mnt : NULL,
+	};
+
+	if (dir != d_inode(current->nsproxy->ipc_ns->mq_mnt->mnt_root))
+		pr_warn("apparmor: unlink dir != mnt_root - disconnected");
+
+	return common_mqueue_path_perm(op, request, &path);
+}
+
+static int apparmor_inode_unlink(struct inode *dir, struct dentry *dentry)
+{
+	int error = 0;
+
+	if (is_mqueue_dentry(dentry))
+		error = common_mqueue_perm(OP_UNLINK, AA_MAY_DELETE, dir, dentry);
+
+	return error;
+}
+
+static int apparmor_inode_setattr(struct dentry *dentry, struct iattr *iattr)
+{
+	/* TODO: extend to support iattr as a parameter */
+	if (is_mqueue_dentry(dentry))
+		/* TODO: fn() for d_parent */
+		return common_mqueue_perm(OP_UNLINK, AA_MAY_SETATTR,
+				  d_backing_inode(dentry->d_parent), dentry);
+
+	return 0;
+}
+
 static int apparmor_file_open(struct file *file)
 {
 	struct aa_file_ctx *fctx = file_ctx(file);
@@ -432,10 +597,15 @@
 			inode->i_mode
 		};
 
-		error = aa_path_perm(OP_OPEN, label, &file->f_path, 0,
-				     aa_map_file_to_perms(file), &cond);
+		if (is_mqueue_inode(file_inode(file)))
+			error = aa_mqueue_perm(OP_OPEN, label, &file->f_path,
+					       aa_map_file_to_perms(file));
+		else
+			error = aa_path_perm(OP_OPEN, label, &file->f_path, 0,
+					     aa_map_file_to_perms(file), &cond);
 		/* todo cache full allowed permissions set and state */
-		fctx->allow = aa_map_file_to_perms(file);
+		if (!error)
+			fctx->allow = aa_map_file_to_perms(file);
 	}
 	aa_put_label(label);
 
@@ -447,6 +617,7 @@
 	struct aa_file_ctx *ctx = file_ctx(file);
 	struct aa_label *label = begin_current_label_crit_section();
 
+	/* no inode available here */
 	spin_lock_init(&ctx->lock);
 	rcu_assign_pointer(ctx->label, aa_get_label(label));
 	end_current_label_crit_section(label);
@@ -602,6 +773,7 @@
 	const struct cred *cred = get_task_cred(task);
 	struct aa_task_ctx *ctx = task_ctx(current);
 	struct aa_label *label = NULL;
+	bool newline = true;
 
 	if (strcmp(name, "current") == 0)
 		label = aa_get_newest_label(cred_label(cred));
@@ -609,11 +781,14 @@
 		label = aa_get_newest_label(ctx->previous);
 	else if (strcmp(name, "exec") == 0 && ctx->onexec)
 		label = aa_get_newest_label(ctx->onexec);
-	else
+	else if (strcmp(name, "context") == 0) {
+		label = aa_get_newest_label(cred_label(cred));
+		newline = false;
+	} else
 		error = -EINVAL;
 
 	if (label)
-		error = aa_getprocattr(label, value);
+		error = aa_getprocattr(label, value, newline);
 
 	aa_put_label(label);
 	put_cred(cred);
@@ -621,6 +796,25 @@
 	return error;
 }
 
+
+static int profile_display_lsm(struct aa_profile *profile,
+			       struct common_audit_data *sa)
+{
+	struct aa_perms perms = { };
+	unsigned int state;
+
+	state = PROFILE_MEDIATES(profile, AA_CLASS_DISPLAY_LSM);
+	if (state) {
+		aa_compute_perms(profile->policy.dfa, state, &perms);
+		aa_apply_modes_to_perms(profile, &perms);
+		aad(sa)->label = &profile->label;
+
+		return aa_check_perms(profile, &perms, AA_MAY_WRITE, sa, NULL);
+	}
+
+	return 0;
+}
+
 static int apparmor_setprocattr(const char *name, void *value,
 				size_t size)
 {
@@ -632,6 +826,19 @@
 	if (size == 0)
 		return -EINVAL;
 
+	/* LSM infrastructure does actual setting of display if allowed */
+	if (!strcmp(name, "display")) {
+		struct aa_profile *profile;
+		struct aa_label *label;
+
+		aad(&sa)->info = "set display lsm";
+		label = begin_current_label_crit_section();
+		error = fn_for_each_confined(label, profile,
+					     profile_display_lsm(profile, &sa));
+		end_current_label_crit_section(label);
+		return error;
+	}
+
 	/* AppArmor requires that the buffer must be null terminated atm */
 	if (args[size - 1] != '\0') {
 		/* null terminate */
@@ -776,32 +983,15 @@
 }
 
 /**
- * apparmor_sk_alloc_security - allocate and attach the sk_security field
- */
-static int apparmor_sk_alloc_security(struct sock *sk, int family, gfp_t flags)
-{
-	struct aa_sk_ctx *ctx;
-
-	ctx = kzalloc(sizeof(*ctx), flags);
-	if (!ctx)
-		return -ENOMEM;
-
-	SK_CTX(sk) = ctx;
-
-	return 0;
-}
-
-/**
  * apparmor_sk_free_security - free the sk_security field
  */
 static void apparmor_sk_free_security(struct sock *sk)
 {
-	struct aa_sk_ctx *ctx = SK_CTX(sk);
+	struct aa_sk_ctx *ctx = aa_sock(sk);
 
-	SK_CTX(sk) = NULL;
 	aa_put_label(ctx->label);
 	aa_put_label(ctx->peer);
-	kfree(ctx);
+	path_put(&ctx->path);
 }
 
 /**
@@ -810,8 +1000,8 @@
 static void apparmor_sk_clone_security(const struct sock *sk,
 				       struct sock *newsk)
 {
-	struct aa_sk_ctx *ctx = SK_CTX(sk);
-	struct aa_sk_ctx *new = SK_CTX(newsk);
+	struct aa_sk_ctx *ctx = aa_sock(sk);
+	struct aa_sk_ctx *new = aa_sock(newsk);
 
 	if (new->label)
 		aa_put_label(new->label);
@@ -820,6 +1010,99 @@
 	if (new->peer)
 		aa_put_label(new->peer);
 	new->peer = aa_get_label(ctx->peer);
+	new->path = ctx->path;
+	path_get(&new->path);
+}
+
+static struct path *UNIX_FS_CONN_PATH(struct sock *sk, struct sock *newsk)
+{
+	if (sk->sk_family == PF_UNIX && UNIX_FS(sk))
+		return &unix_sk(sk)->path;
+	else if (newsk->sk_family == PF_UNIX && UNIX_FS(newsk))
+		return &unix_sk(newsk)->path;
+	return NULL;
+}
+
+/**
+ * apparmor_unix_stream_connect - check perms before making unix domain conn
+ *
+ * peer is locked when this hook is called
+ */
+static int apparmor_unix_stream_connect(struct sock *sk, struct sock *peer_sk,
+					struct sock *newsk)
+{
+	struct aa_sk_ctx *sk_ctx = aa_sock(sk);
+	struct aa_sk_ctx *peer_ctx = aa_sock(peer_sk);
+	struct aa_sk_ctx *new_ctx = aa_sock(newsk);
+	struct aa_label *label;
+	struct path *path;
+	int error;
+
+	label = __begin_current_label_crit_section();
+	error = aa_unix_peer_perm(label, OP_CONNECT,
+				(AA_MAY_CONNECT | AA_MAY_SEND | AA_MAY_RECEIVE),
+				  sk, peer_sk, NULL);
+	if (!UNIX_FS(peer_sk)) {
+		last_error(error,
+			aa_unix_peer_perm(peer_ctx->label, OP_CONNECT,
+				(AA_MAY_ACCEPT | AA_MAY_SEND | AA_MAY_RECEIVE),
+				peer_sk, sk, label));
+	}
+	__end_current_label_crit_section(label);
+
+	if (error)
+		return error;
+
+	/* label newsk if it wasn't labeled in post_create. Normally this
+	 * would be done in sock_graft, but because we are directly looking
+	 * at the peer_sk to obtain peer_labeling for unix socks this
+	 * does not work
+	 */
+	if (!new_ctx->label)
+		new_ctx->label = aa_get_label(peer_ctx->label);
+
+	/* Cross reference the peer labels for SO_PEERSEC */
+	if (new_ctx->peer)
+		aa_put_label(new_ctx->peer);
+
+	if (sk_ctx->peer)
+		aa_put_label(sk_ctx->peer);
+
+	new_ctx->peer = aa_get_label(sk_ctx->label);
+	sk_ctx->peer = aa_get_label(peer_ctx->label);
+
+	path = UNIX_FS_CONN_PATH(sk, peer_sk);
+	if (path) {
+		new_ctx->path = *path;
+		sk_ctx->path = *path;
+		path_get(path);
+		path_get(path);
+	}
+	return 0;
+}
+
+/**
+ * apparmor_unix_may_send - check perms before conn or sending unix dgrams
+ *
+ * other is locked when this hook is called
+ *
+ * dgram connect calls may_send, peer setup but path not copied?????
+ */
+static int apparmor_unix_may_send(struct socket *sock, struct socket *peer)
+{
+	struct aa_sk_ctx *peer_ctx = aa_sock(peer->sk);
+	struct aa_label *label;
+	int error;
+
+	label = __begin_current_label_crit_section();
+	error = xcheck(aa_unix_peer_perm(label, OP_SENDMSG, AA_MAY_SEND,
+					 sock->sk, peer->sk, NULL),
+		       aa_unix_peer_perm(peer_ctx->label, OP_SENDMSG,
+					 AA_MAY_RECEIVE,
+					 peer->sk, sock->sk, label));
+	__end_current_label_crit_section(label);
+
+	return error;
 }
 
 /**
@@ -867,7 +1150,7 @@
 		label = aa_get_current_label();
 
 	if (sock->sk) {
-		struct aa_sk_ctx *ctx = SK_CTX(sock->sk);
+		struct aa_sk_ctx *ctx = aa_sock(sock->sk);
 
 		aa_put_label(ctx->label);
 		ctx->label = aa_get_label(label);
@@ -1052,11 +1335,18 @@
  */
 static int apparmor_socket_sock_rcv_skb(struct sock *sk, struct sk_buff *skb)
 {
-	struct aa_sk_ctx *ctx = SK_CTX(sk);
+	struct aa_sk_ctx *ctx = aa_sock(sk);
 
 	if (!skb->secmark)
 		return 0;
 
+	/*
+	 * If reach here before socket_post_create hook is called, in which
+	 * case label is null, drop the packet.
+	 */
+	if (!ctx->label)
+		return -EACCES;
+
 	return apparmor_secmark_check(ctx->label, OP_RECVMSG, AA_MAY_RECEIVE,
 				      skb->secmark, sk);
 }
@@ -1065,12 +1355,28 @@
 
 static struct aa_label *sk_peer_label(struct sock *sk)
 {
-	struct aa_sk_ctx *ctx = SK_CTX(sk);
+	struct sock *peer_sk;
+	struct aa_sk_ctx *ctx = aa_sock(sk);
+	struct aa_label *label = ERR_PTR(-ENOPROTOOPT);
 
 	if (ctx->peer)
-		return ctx->peer;
+		return aa_get_label(ctx->peer);
+
+	if (sk->sk_family != PF_UNIX)
+		return ERR_PTR(-ENOPROTOOPT);
 
-	return ERR_PTR(-ENOPROTOOPT);
+	/* check for sockpair peering which does not go through
+	 * security_unix_stream_connect
+	 */
+	peer_sk = unix_peer_get(sk);
+	if (peer_sk) {
+		ctx = aa_sock(peer_sk);
+		if (ctx->label)
+			label = aa_get_label(ctx->label);
+		sock_put(peer_sk);
+	}
+
+	return label;
 }
 
 /**
@@ -1114,6 +1420,7 @@
 
 	}
 
+	aa_put_label(peer);
 done:
 	end_current_label_crit_section(label);
 
@@ -1121,22 +1428,6 @@
 }
 
 /**
- * apparmor_socket_getpeersec_dgram - get security label of packet
- * @sock: the peer socket
- * @skb: packet data
- * @secid: pointer to where to put the secid of the packet
- *
- * Sets the netlabel socket state on sk from parent
- */
-static int apparmor_socket_getpeersec_dgram(struct socket *sock,
-					    struct sk_buff *skb, u32 *secid)
-
-{
-	/* TODO: requires secid support */
-	return -ENOPROTOOPT;
-}
-
-/**
  * apparmor_sock_graft - Initialize newly created socket
  * @sk: child sock
  * @parent: parent socket
@@ -1149,7 +1440,7 @@
  */
 static void apparmor_sock_graft(struct sock *sk, struct socket *parent)
 {
-	struct aa_sk_ctx *ctx = SK_CTX(sk);
+	struct aa_sk_ctx *ctx = aa_sock(sk);
 
 	if (!ctx->label)
 		ctx->label = aa_get_current_label();
@@ -1159,7 +1450,7 @@
 static int apparmor_inet_conn_request(const struct sock *sk, struct sk_buff *skb,
 				      struct request_sock *req)
 {
-	struct aa_sk_ctx *ctx = SK_CTX(sk);
+	struct aa_sk_ctx *ctx = aa_sock(sk);
 
 	if (!skb->secmark)
 		return 0;
@@ -1170,12 +1461,22 @@
 #endif
 
 /*
- * The cred blob is a pointer to, not an instance of, an aa_task_ctx.
+ * The cred blob is a pointer to, not an instance of, an aa_label.
  */
 struct lsm_blob_sizes apparmor_blob_sizes __lsm_ro_after_init = {
-	.lbs_cred = sizeof(struct aa_task_ctx *),
+	.lbs_cred = sizeof(struct aa_label *),
 	.lbs_file = sizeof(struct aa_file_ctx),
+	.lbs_inode = sizeof(struct aa_inode_sec),
 	.lbs_task = sizeof(struct aa_task_ctx),
+	.lbs_sock = sizeof(struct aa_sk_ctx),
+	.lbs_ipc = sizeof(struct aa_ipc_sec),
+	.lbs_msg_msg = sizeof(struct aa_msg_sec),
+	.lbs_superblock = sizeof(struct aa_superblock_sec),
+};
+
+static struct lsm_id apparmor_lsmid __lsm_ro_after_init = {
+	.lsm  = "apparmor",
+	.slot = LSMBLOB_NEEDED
 };
 
 static struct security_hook_list apparmor_hooks[] __lsm_ro_after_init = {
@@ -1200,6 +1501,16 @@
 	LSM_HOOK_INIT(path_truncate, apparmor_path_truncate),
 	LSM_HOOK_INIT(inode_getattr, apparmor_inode_getattr),
 
+	LSM_HOOK_INIT(inode_alloc_security, apparmor_inode_alloc_security),
+	LSM_HOOK_INIT(inode_free_security, apparmor_inode_free_security),
+	LSM_HOOK_INIT(inode_init_security, apparmor_inode_init_security),
+	LSM_HOOK_INIT(d_instantiate, apparmor_d_instantiate),
+
+	LSM_HOOK_INIT(inode_create, apparmor_inode_create),
+	LSM_HOOK_INIT(inode_unlink, apparmor_inode_unlink),
+	LSM_HOOK_INIT(inode_setattr, apparmor_inode_setattr),
+	LSM_HOOK_INIT(inode_getattr, apparmor_inode_getattr),
+
 	LSM_HOOK_INIT(file_open, apparmor_file_open),
 	LSM_HOOK_INIT(file_receive, apparmor_file_receive),
 	LSM_HOOK_INIT(file_permission, apparmor_file_permission),
@@ -1212,10 +1523,12 @@
 	LSM_HOOK_INIT(getprocattr, apparmor_getprocattr),
 	LSM_HOOK_INIT(setprocattr, apparmor_setprocattr),
 
-	LSM_HOOK_INIT(sk_alloc_security, apparmor_sk_alloc_security),
 	LSM_HOOK_INIT(sk_free_security, apparmor_sk_free_security),
 	LSM_HOOK_INIT(sk_clone_security, apparmor_sk_clone_security),
 
+	LSM_HOOK_INIT(unix_stream_connect, apparmor_unix_stream_connect),
+	LSM_HOOK_INIT(unix_may_send, apparmor_unix_may_send),
+
 	LSM_HOOK_INIT(socket_create, apparmor_socket_create),
 	LSM_HOOK_INIT(socket_post_create, apparmor_socket_post_create),
 	LSM_HOOK_INIT(socket_bind, apparmor_socket_bind),
@@ -1234,8 +1547,6 @@
 #endif
 	LSM_HOOK_INIT(socket_getpeersec_stream,
 		      apparmor_socket_getpeersec_stream),
-	LSM_HOOK_INIT(socket_getpeersec_dgram,
-		      apparmor_socket_getpeersec_dgram),
 	LSM_HOOK_INIT(sock_graft, apparmor_sock_graft),
 #ifdef CONFIG_NETWORK_SECMARK
 	LSM_HOOK_INIT(inet_conn_request, apparmor_inet_conn_request),
@@ -1734,6 +2045,14 @@
 		.mode           = 0600,
 		.proc_handler   = apparmor_dointvec,
 	},
+	{
+		.procname       = "apparmor_display_secid_mode",
+		.data           = &apparmor_display_secid_mode,
+		.maxlen         = sizeof(int),
+		.mode           = 0600,
+		.proc_handler   = apparmor_dointvec,
+	},
+
 	{ }
 };
 
@@ -1764,7 +2083,7 @@
 	if (sk == NULL)
 		return NF_ACCEPT;
 
-	ctx = SK_CTX(sk);
+	ctx = aa_sock(sk);
 	if (!apparmor_secmark_check(ctx->label, OP_SENDMSG, AA_MAY_SEND,
 				    skb->secmark, sk))
 		return NF_ACCEPT;
@@ -1880,7 +2199,7 @@
 		goto buffers_out;
 	}
 	security_add_hooks(apparmor_hooks, ARRAY_SIZE(apparmor_hooks),
-				"apparmor");
+				&apparmor_lsmid);
 
 	/* Report that AppArmor successfully initialized */
 	apparmor_initialized = 1;
@@ -1905,7 +2224,7 @@
 
 DEFINE_LSM(apparmor) = {
 	.name = "apparmor",
-	.flags = LSM_FLAG_LEGACY_MAJOR | LSM_FLAG_EXCLUSIVE,
+	.flags = LSM_FLAG_LEGACY_MAJOR,
 	.enabled = &apparmor_enabled,
 	.blobs = &apparmor_blob_sizes,
 	.init = apparmor_init,
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/mount.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/mount.c
@@ -229,7 +229,8 @@
 	"failed srcname match",
 	"failed type match",
 	"failed flags match",
-	"failed data match"
+	"failed data match",
+	"failed perms check"
 };
 
 /*
@@ -284,8 +285,8 @@
 			return 0;
 	}
 
-	/* failed at end of flags match */
-	return 4;
+	/* failed at perms check, don't confuse with flags match */
+	return 6;
 }
 
 
@@ -718,6 +719,7 @@
 			aa_put_label(target);
 			goto out;
 		}
+		aa_put_label(target);
 	} else
 		/* already audited error */
 		error = PTR_ERR(target);
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/net.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/net.c
@@ -8,6 +8,7 @@
  * Copyright 2009-2017 Canonical Ltd.
  */
 
+#include "include/af_unix.h"
 #include "include/apparmor.h"
 #include "include/audit.h"
 #include "include/cred.h"
@@ -24,6 +25,12 @@
 	{ }
 };
 
+struct aa_sfs_entry aa_sfs_entry_network_compat[] = {
+	AA_SFS_FILE_STRING("af_mask",	AA_SFS_AF_MASK),
+	AA_SFS_FILE_BOOLEAN("af_unix",	1),
+	{ }
+};
+
 static const char * const net_mask_names[] = {
 	"unknown",
 	"send",
@@ -66,6 +73,36 @@
 	"unknown",
 };
 
+static void audit_unix_addr(struct audit_buffer *ab, const char *str,
+			    struct sockaddr_un *addr, int addrlen)
+{
+	int len = unix_addr_len(addrlen);
+
+	if (!addr || len <= 0) {
+		audit_log_format(ab, " %s=none", str);
+	} else if (addr->sun_path[0]) {
+		audit_log_format(ab, " %s=", str);
+		audit_log_untrustedstring(ab, addr->sun_path);
+	} else {
+		audit_log_format(ab, " %s=\"@", str);
+		if (audit_string_contains_control(&addr->sun_path[1], len - 1))
+			audit_log_n_hex(ab, &addr->sun_path[1], len - 1);
+		else
+			audit_log_format(ab, "%.*s", len - 1,
+					 &addr->sun_path[1]);
+		audit_log_format(ab, "\"");
+	}
+}
+
+static void audit_unix_sk_addr(struct audit_buffer *ab, const char *str,
+			       const struct sock *sk)
+{
+	struct unix_sock *u = unix_sk(sk);
+	if (u && u->addr)
+		audit_unix_addr(ab, str, u->addr->name, u->addr->len);
+	else
+		audit_unix_addr(ab, str, NULL, 0);
+}
 
 /* audit callback for net specific fields */
 void audit_net_cb(struct audit_buffer *ab, void *va)
@@ -97,6 +134,23 @@
 					   net_mask_names, NET_PERMS_MASK);
 		}
 	}
+	if (sa->u.net->family == AF_UNIX) {
+		if ((aad(sa)->request & ~NET_PEER_MASK) && aad(sa)->net.addr)
+			audit_unix_addr(ab, "addr",
+					unix_addr(aad(sa)->net.addr),
+					aad(sa)->net.addrlen);
+		else
+			audit_unix_sk_addr(ab, "addr", sa->u.net->sk);
+		if (aad(sa)->request & NET_PEER_MASK) {
+			if (aad(sa)->net.addr)
+				audit_unix_addr(ab, "peer_addr",
+						unix_addr(aad(sa)->net.addr),
+						aad(sa)->net.addrlen);
+			else
+				audit_unix_sk_addr(ab, "peer_addr",
+						   aad(sa)->net.peer_sk);
+		}
+	}
 	if (aad(sa)->peer) {
 		audit_log_format(ab, " peer=");
 		aa_label_xaudit(ab, labels_ns(aad(sa)->label), aad(sa)->peer,
@@ -118,14 +172,26 @@
 	if (profile_unconfined(profile))
 		return 0;
 	state = PROFILE_MEDIATES(profile, AA_CLASS_NET);
-	if (!state)
-		return 0;
+	if (state) {
+		if (!state)
+			return 0;
+		buffer[0] = cpu_to_be16(family);
+		buffer[1] = cpu_to_be16((u16) type);
+		state = aa_dfa_match_len(profile->policy.dfa, state,
+					 (char *) &buffer, 4);
+		aa_compute_perms(profile->policy.dfa, state, &perms);
+	} else if (profile->net_compat) {
+		/* 2.x socket mediation compat */
+		perms.allow = (profile->net_compat->allow[family] & (1 << type)) ?
+			ALL_PERMS_MASK : 0;
+		perms.audit = (profile->net_compat->audit[family] & (1 << type)) ?
+			ALL_PERMS_MASK : 0;
+		perms.quiet = (profile->net_compat->quiet[family] & (1 << type)) ?
+			ALL_PERMS_MASK : 0;
 
-	buffer[0] = cpu_to_be16(family);
-	buffer[1] = cpu_to_be16((u16) type);
-	state = aa_dfa_match_len(profile->policy.dfa, state, (char *) &buffer,
-				 4);
-	aa_compute_perms(profile->policy.dfa, state, &perms);
+	} else {
+		return 0;
+	}
 	aa_apply_modes_to_perms(profile, &perms);
 
 	return aa_check_perms(profile, &perms, request, sa, audit_net_cb);
@@ -185,7 +251,9 @@
 	AA_BUG(!sock);
 	AA_BUG(!sock->sk);
 
-	return aa_label_sk_perm(label, op, request, sock->sk);
+	return af_select(sock->sk->sk_family,
+			 file_perm(label, op, request, sock),
+			 aa_label_sk_perm(label, op, request, sock->sk));
 }
 
 #ifdef CONFIG_NETWORK_SECMARK
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/policy.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/policy.c
@@ -187,7 +187,7 @@
 {
 	struct aa_data *data = ptr;
 
-	kfree_sensitive(data->data);
+	kvfree_sensitive(data->data, data->size);
 	kfree_sensitive(data->key);
 	kfree_sensitive(data);
 }
@@ -222,6 +222,7 @@
 	aa_free_file_rules(&profile->file);
 	aa_free_cap_rules(&profile->caps);
 	aa_free_rlimit_rules(&profile->rlimits);
+	kfree_sensitive(profile->net_compat);
 
 	for (i = 0; i < profile->xattr_count; i++)
 		kfree_sensitive(profile->xattrs[i]);
@@ -1125,7 +1126,7 @@
 
 	if (!name) {
 		/* remove namespace - can only happen if fqname[0] == ':' */
-		mutex_lock_nested(&ns->parent->lock, ns->level);
+		mutex_lock_nested(&ns->parent->lock, ns->parent->level);
 		__aa_bump_ns_revision(ns);
 		__aa_remove_ns(ns);
 		mutex_unlock(&ns->parent->lock);
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/policy_ns.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/policy_ns.c
@@ -121,7 +121,7 @@
 	return ns;
 
 fail_unconfined:
-	kfree_sensitive(ns->base.hname);
+	aa_policy_destroy(&ns->base);
 fail_ns:
 	kfree_sensitive(ns);
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/policy_unpack.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/policy_unpack.c
@@ -34,7 +34,7 @@
 
 #define v5	5	/* base version */
 #define v6	6	/* per entry policydb mediation check */
-#define v7	7
+#define v7	7	/* v2 compat networking */
 #define v8	8	/* full network masking */
 
 /*
@@ -314,6 +314,19 @@
 	return false;
 }
 
+static bool unpack_u16(struct aa_ext *e, u16 *data, const char *name)
+{
+	if (unpack_nameX(e, AA_U16, name)) {
+		if (!inbounds(e, sizeof(u16)))
+			return 0;
+		if (data)
+			*data = le16_to_cpu(get_unaligned((__le16 *) e->pos));
+		e->pos += sizeof(u16);
+		return 1;
+	}
+	return 0;
+}
+
 static bool unpack_u32(struct aa_ext *e, u32 *data, const char *name)
 {
 	void *pos = e->pos;
@@ -676,7 +689,7 @@
 	struct aa_profile *profile = NULL;
 	const char *tmpname, *tmpns = NULL, *name = NULL;
 	const char *info = "failed to unpack profile";
-	size_t ns_len;
+	size_t size = 0, ns_len;
 	struct rhashtable_params params = { 0 };
 	char *key = NULL;
 	struct aa_data *data;
@@ -696,6 +709,10 @@
 
 	tmpname = aa_splitn_fqname(name, strlen(name), &tmpns, &ns_len);
 	if (tmpns) {
+		if (!tmpname) {
+			info = "empty profile name";
+			goto fail;
+		}
 		*ns_name = kstrndup(tmpns, ns_len, GFP_KERNEL);
 		if (!*ns_name) {
 			info = "out of memory";
@@ -746,16 +763,18 @@
 		profile->label.flags |= FLAG_HAT;
 	if (!unpack_u32(e, &tmp, NULL))
 		goto fail;
-	if (tmp == PACKED_MODE_COMPLAIN || (e->version & FORCE_COMPLAIN_FLAG))
+	if (tmp == PACKED_MODE_COMPLAIN || (e->version & FORCE_COMPLAIN_FLAG)) {
 		profile->mode = APPARMOR_COMPLAIN;
-	else if (tmp == PACKED_MODE_ENFORCE)
+	} else if (tmp == PACKED_MODE_ENFORCE) {
 		profile->mode = APPARMOR_ENFORCE;
-	else if (tmp == PACKED_MODE_KILL)
+	} else if (tmp == PACKED_MODE_KILL) {
 		profile->mode = APPARMOR_KILL;
-	else if (tmp == PACKED_MODE_UNCONFINED)
+	} else if (tmp == PACKED_MODE_UNCONFINED) {
 		profile->mode = APPARMOR_UNCONFINED;
-	else
+		profile->label.flags |= FLAG_UNCONFINED;
+	} else {
 		goto fail;
+	}
 	if (!unpack_u32(e, &tmp, NULL))
 		goto fail;
 	if (tmp)
@@ -823,6 +842,43 @@
 		goto fail;
 	}
 
+	size = unpack_array(e, "net_allowed_af");
+	if (size || VERSION_LT(e->version, v8)) {
+		profile->net_compat = kzalloc(sizeof(struct aa_net_compat), GFP_KERNEL);
+		if (!profile->net_compat) {
+			info = "out of memory";
+			goto fail;
+		}
+		for (i = 0; i < size; i++) {
+			/* discard extraneous rules that this kernel will
+			 * never request
+			 */
+			if (i >= AF_MAX) {
+				u16 tmp;
+
+				if (!unpack_u16(e, &tmp, NULL) ||
+				    !unpack_u16(e, &tmp, NULL) ||
+				    !unpack_u16(e, &tmp, NULL))
+					goto fail;
+				continue;
+			}
+			if (!unpack_u16(e, &profile->net_compat->allow[i], NULL))
+				goto fail;
+			if (!unpack_u16(e, &profile->net_compat->audit[i], NULL))
+				goto fail;
+			if (!unpack_u16(e, &profile->net_compat->quiet[i], NULL))
+				goto fail;
+		}
+		if (size && !unpack_nameX(e, AA_ARRAYEND, NULL))
+			goto fail;
+		if (VERSION_LT(e->version, v7)) {
+			/* pre v7 policy always allowed these */
+			profile->net_compat->allow[AF_UNIX] = 0xffff;
+			profile->net_compat->allow[AF_NETLINK] = 0xffff;
+		}
+	}
+
+
 	if (unpack_nameX(e, AA_STRUCT, "policydb")) {
 		/* generic policy dfa - optional and may be NULL */
 		info = "failed to unpack policydb";
@@ -907,8 +963,14 @@
 				goto fail;
 			}
 
-			rhashtable_insert_fast(profile->data, &data->head,
-					       profile->data->p);
+			if (rhashtable_insert_fast(profile->data, &data->head,
+						   profile->data->p)) {
+				kvfree_sensitive(data->data, data->size);
+				kfree_sensitive(data->key);
+				kfree_sensitive(data);
+				info = "failed to insert data to table";
+				goto fail;
+			}
 		}
 
 		if (!unpack_nameX(e, AA_STRUCTEND, NULL)) {
@@ -962,7 +1024,7 @@
 	 * if not specified use previous version
 	 * Mask off everything that is not kernel abi version
 	 */
-	if (VERSION_LT(e->version, v5) || VERSION_GT(e->version, v7)) {
+	if (VERSION_LT(e->version, v5) || VERSION_GT(e->version, v8)) {
 		audit_iface(NULL, NULL, NULL, "unsupported interface version",
 			    e, error);
 		return error;
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/policy_unpack_test.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/policy_unpack_test.c
@@ -78,14 +78,14 @@
 	*(buf + 1) = strlen(TEST_U32_NAME) + 1;
 	strcpy(buf + 3, TEST_U32_NAME);
 	*(buf + 3 + strlen(TEST_U32_NAME) + 1) = AA_U32;
-	*((u32 *)(buf + 3 + strlen(TEST_U32_NAME) + 2)) = TEST_U32_DATA;
+	*((__le32 *)(buf + 3 + strlen(TEST_U32_NAME) + 2)) = cpu_to_le32(TEST_U32_DATA);
 
 	buf = e->start + TEST_NAMED_U64_BUF_OFFSET;
 	*buf = AA_NAME;
 	*(buf + 1) = strlen(TEST_U64_NAME) + 1;
 	strcpy(buf + 3, TEST_U64_NAME);
 	*(buf + 3 + strlen(TEST_U64_NAME) + 1) = AA_U64;
-	*((u64 *)(buf + 3 + strlen(TEST_U64_NAME) + 2)) = TEST_U64_DATA;
+	*((__le64 *)(buf + 3 + strlen(TEST_U64_NAME) + 2)) = cpu_to_le64(TEST_U64_DATA);
 
 	buf = e->start + TEST_NAMED_BLOB_BUF_OFFSET;
 	*buf = AA_NAME;
@@ -101,7 +101,7 @@
 	*(buf + 1) = strlen(TEST_ARRAY_NAME) + 1;
 	strcpy(buf + 3, TEST_ARRAY_NAME);
 	*(buf + 3 + strlen(TEST_ARRAY_NAME) + 1) = AA_ARRAY;
-	*((u16 *)(buf + 3 + strlen(TEST_ARRAY_NAME) + 2)) = TEST_ARRAY_SIZE;
+	*((__le16 *)(buf + 3 + strlen(TEST_ARRAY_NAME) + 2)) = cpu_to_le16(TEST_ARRAY_SIZE);
 
 	return e;
 }
@@ -283,6 +283,8 @@
 			   ((uintptr_t)puf->e->start <= (uintptr_t)string)
 			   && ((uintptr_t)string <= (uintptr_t)puf->e->end));
 	KUNIT_EXPECT_STREQ(test, string, TEST_STRING_DATA);
+
+	kfree(string);
 }
 
 static void policy_unpack_test_unpack_strdup_with_name(struct kunit *test)
@@ -298,6 +300,8 @@
 			   ((uintptr_t)puf->e->start <= (uintptr_t)string)
 			   && ((uintptr_t)string <= (uintptr_t)puf->e->end));
 	KUNIT_EXPECT_STREQ(test, string, TEST_STRING_DATA);
+
+	kfree(string);
 }
 
 static void policy_unpack_test_unpack_strdup_out_of_bounds(struct kunit *test)
@@ -315,6 +319,8 @@
 	KUNIT_EXPECT_EQ(test, size, 0);
 	KUNIT_EXPECT_PTR_EQ(test, string, (char *)NULL);
 	KUNIT_EXPECT_PTR_EQ(test, puf->e->pos, start);
+
+	kfree(string);
 }
 
 static void policy_unpack_test_unpack_nameX_with_null_name(struct kunit *test)
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/procattr.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/procattr.c
@@ -20,6 +20,7 @@
  * aa_getprocattr - Return the profile information for @profile
  * @profile: the profile to print profile info about  (NOT NULL)
  * @string: Returns - string containing the profile info (NOT NULL)
+ * @newline: Should a newline be added to @string.
  *
  * Returns: length of @string on success else error on failure
  *
@@ -30,20 +31,21 @@
  *
  * Returns: size of string placed in @string else error code on failure
  */
-int aa_getprocattr(struct aa_label *label, char **string)
+int aa_getprocattr(struct aa_label *label, char **string, bool newline)
 {
 	struct aa_ns *ns = labels_ns(label);
 	struct aa_ns *current_ns = aa_get_current_ns();
+	int flags = FLAG_VIEW_SUBNS | FLAG_HIDDEN_UNCONFINED;
 	int len;
 
 	if (!aa_ns_visible(current_ns, ns, true)) {
 		aa_put_ns(current_ns);
 		return -EACCES;
 	}
+	if (newline)
+		flags |= FLAG_SHOW_MODE;
 
-	len = aa_label_snxprint(NULL, 0, current_ns, label,
-				FLAG_SHOW_MODE | FLAG_VIEW_SUBNS |
-				FLAG_HIDDEN_UNCONFINED);
+	len = aa_label_snxprint(NULL, 0, current_ns, label, flags);
 	AA_BUG(len < 0);
 
 	*string = kmalloc(len + 2, GFP_KERNEL);
@@ -52,19 +54,19 @@
 		return -ENOMEM;
 	}
 
-	len = aa_label_snxprint(*string, len + 2, current_ns, label,
-				FLAG_SHOW_MODE | FLAG_VIEW_SUBNS |
-				FLAG_HIDDEN_UNCONFINED);
+	len = aa_label_snxprint(*string, len + 2, current_ns, label, flags);
 	if (len < 0) {
 		aa_put_ns(current_ns);
 		return len;
 	}
 
-	(*string)[len] = '\n';
-	(*string)[len + 1] = 0;
+	if (newline) {
+		(*string)[len] = '\n';
+		(*string)[++len] = 0;
+	}
 
 	aa_put_ns(current_ns);
-	return len + 1;
+	return len;
 }
 
 /**
--- linux-xilinx-zynqmp-5.15.0.orig/security/apparmor/secid.c
+++ linux-xilinx-zynqmp-5.15.0/security/apparmor/secid.c
@@ -32,6 +32,8 @@
 static DEFINE_IDR(aa_secids);
 static DEFINE_SPINLOCK(secid_lock);
 
+int apparmor_display_secid_mode = 0;
+
 /*
  * TODO: allow policy to reserve a secid range?
  * TODO: add secid pinning
@@ -71,6 +73,7 @@
 {
 	/* TODO: cache secctx and ref count so we don't have to recreate */
 	struct aa_label *label = aa_secid_to_label(secid);
+	int flags = FLAG_VIEW_SUBNS | FLAG_HIDDEN_UNCONFINED | FLAG_ABS_ROOT;
 	int len;
 
 	AA_BUG(!seclen);
@@ -78,15 +81,15 @@
 	if (!label)
 		return -EINVAL;
 
+	if (apparmor_display_secid_mode)
+		flags |= FLAG_SHOW_MODE;
+
 	if (secdata)
 		len = aa_label_asxprint(secdata, root_ns, label,
-					FLAG_SHOW_MODE | FLAG_VIEW_SUBNS |
-					FLAG_HIDDEN_UNCONFINED | FLAG_ABS_ROOT,
-					GFP_ATOMIC);
+					flags, GFP_ATOMIC);
 	else
-		len = aa_label_snxprint(NULL, 0, root_ns, label,
-					FLAG_SHOW_MODE | FLAG_VIEW_SUBNS |
-					FLAG_HIDDEN_UNCONFINED | FLAG_ABS_ROOT);
+		len = aa_label_snxprint(NULL, 0, root_ns, label, flags);
+
 	if (len < 0)
 		return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/bpf/hooks.c
+++ linux-xilinx-zynqmp-5.15.0/security/bpf/hooks.c
@@ -15,16 +15,25 @@
 	LSM_HOOK_INIT(task_free, bpf_task_storage_free),
 };
 
+/*
+ * slot has to be LSMBLOB_NEEDED because some of the hooks
+ * supplied by this module require a slot.
+ */
+struct lsm_id bpf_lsmid __lsm_ro_after_init = {
+	.lsm = "bpf",
+	.slot = LSMBLOB_NEEDED
+};
+
 static int __init bpf_lsm_init(void)
 {
-	security_add_hooks(bpf_lsm_hooks, ARRAY_SIZE(bpf_lsm_hooks), "bpf");
+	security_add_hooks(bpf_lsm_hooks, ARRAY_SIZE(bpf_lsm_hooks),
+			   &bpf_lsmid);
 	pr_info("LSM support for eBPF active\n");
 	return 0;
 }
 
 struct lsm_blob_sizes bpf_lsm_blob_sizes __lsm_ro_after_init = {
 	.lbs_inode = sizeof(struct bpf_storage_blob),
-	.lbs_task = sizeof(struct bpf_storage_blob),
 };
 
 DEFINE_LSM(bpf) = {
--- linux-xilinx-zynqmp-5.15.0.orig/security/commoncap.c
+++ linux-xilinx-zynqmp-5.15.0/security/commoncap.c
@@ -24,6 +24,7 @@
 #include <linux/user_namespace.h>
 #include <linux/binfmts.h>
 #include <linux/personality.h>
+#include <linux/mnt_idmapping.h>
 
 /*
  * If a non-root user executes a setuid-root binary in
@@ -400,8 +401,10 @@
 				      &tmpbuf, size, GFP_NOFS);
 	dput(dentry);
 
-	if (ret < 0 || !tmpbuf)
-		return ret;
+	if (ret < 0 || !tmpbuf) {
+		size = ret;
+		goto out_free;
+	}
 
 	fs_ns = inode->i_sb->s_user_ns;
 	cap = (struct vfs_cap_data *) tmpbuf;
@@ -418,7 +421,7 @@
 	kroot = make_kuid(fs_ns, root);
 
 	/* If this is an idmapped mount shift the kuid. */
-	kroot = kuid_into_mnt(mnt_userns, kroot);
+	kroot = mapped_kuid_fs(mnt_userns, fs_ns, kroot);
 
 	/* If the root kuid maps to a valid uid in current ns, then return
 	 * this as a nscap. */
@@ -488,6 +491,7 @@
  * @size:	size of @ivalue
  * @task_ns:	user namespace of the caller
  * @mnt_userns:	user namespace of the mount the inode was found from
+ * @fs_userns:	user namespace of the filesystem
  *
  * If the inode has been found through an idmapped mount the user namespace of
  * the vfsmount must be passed through @mnt_userns. This function will then
@@ -497,7 +501,8 @@
  */
 static kuid_t rootid_from_xattr(const void *value, size_t size,
 				struct user_namespace *task_ns,
-				struct user_namespace *mnt_userns)
+				struct user_namespace *mnt_userns,
+				struct user_namespace *fs_userns)
 {
 	const struct vfs_ns_cap_data *nscap = value;
 	kuid_t rootkid;
@@ -507,7 +512,7 @@
 		rootid = le32_to_cpu(nscap->rootid);
 
 	rootkid = make_kuid(task_ns, rootid);
-	return kuid_from_mnt(mnt_userns, rootkid);
+	return mapped_kuid_user(mnt_userns, fs_userns, rootkid);
 }
 
 static bool validheader(size_t size, const struct vfs_cap_data *cap)
@@ -553,12 +558,12 @@
 		return -EINVAL;
 	if (!capable_wrt_inode_uidgid(mnt_userns, inode, CAP_SETFCAP))
 		return -EPERM;
-	if (size == XATTR_CAPS_SZ_2 && (mnt_userns == &init_user_ns))
+	if (size == XATTR_CAPS_SZ_2 && (mnt_userns == fs_ns))
 		if (ns_capable(inode->i_sb->s_user_ns, CAP_SETFCAP))
 			/* user is privileged, just write the v2 */
 			return size;
 
-	rootid = rootid_from_xattr(*ivalue, size, task_ns, mnt_userns);
+	rootid = rootid_from_xattr(*ivalue, size, task_ns, mnt_userns, fs_ns);
 	if (!uid_valid(rootid))
 		return -EINVAL;
 
@@ -699,7 +704,7 @@
 	/* Limit the caps to the mounter of the filesystem
 	 * or the more limited uid specified in the xattr.
 	 */
-	rootkuid = kuid_into_mnt(mnt_userns, rootkuid);
+	rootkuid = mapped_kuid_fs(mnt_userns, fs_ns, rootkuid);
 	if (!rootid_owns_currentns(rootkuid))
 		return -ENODATA;
 
@@ -1443,6 +1448,11 @@
 
 #ifdef CONFIG_SECURITY
 
+static struct lsm_id capability_lsmid __lsm_ro_after_init = {
+	.lsm  = "capability",
+	.slot = LSMBLOB_NOT_NEEDED
+};
+
 static struct security_hook_list capability_hooks[] __lsm_ro_after_init = {
 	LSM_HOOK_INIT(capable, cap_capable),
 	LSM_HOOK_INIT(settime, cap_settime),
@@ -1467,7 +1477,7 @@
 static int __init capability_init(void)
 {
 	security_add_hooks(capability_hooks, ARRAY_SIZE(capability_hooks),
-				"capability");
+			   &capability_lsmid);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/device_cgroup.c
+++ linux-xilinx-zynqmp-5.15.0/security/device_cgroup.c
@@ -81,6 +81,17 @@
 	return -ENOMEM;
 }
 
+static void dev_exceptions_move(struct list_head *dest, struct list_head *orig)
+{
+	struct dev_exception_item *ex, *tmp;
+
+	lockdep_assert_held(&devcgroup_mutex);
+
+	list_for_each_entry_safe(ex, tmp, orig, list) {
+		list_move_tail(&ex->list, dest);
+	}
+}
+
 /*
  * called under devcgroup_mutex
  */
@@ -603,11 +614,13 @@
 	int count, rc = 0;
 	struct dev_exception_item ex;
 	struct dev_cgroup *parent = css_to_devcgroup(devcgroup->css.parent);
+	struct dev_cgroup tmp_devcgrp;
 
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
 
 	memset(&ex, 0, sizeof(ex));
+	memset(&tmp_devcgrp, 0, sizeof(tmp_devcgrp));
 	b = buffer;
 
 	switch (*b) {
@@ -619,15 +632,27 @@
 
 			if (!may_allow_all(parent))
 				return -EPERM;
-			dev_exception_clean(devcgroup);
-			devcgroup->behavior = DEVCG_DEFAULT_ALLOW;
-			if (!parent)
+			if (!parent) {
+				devcgroup->behavior = DEVCG_DEFAULT_ALLOW;
+				dev_exception_clean(devcgroup);
 				break;
+			}
 
+			INIT_LIST_HEAD(&tmp_devcgrp.exceptions);
+			rc = dev_exceptions_copy(&tmp_devcgrp.exceptions,
+						 &devcgroup->exceptions);
+			if (rc)
+				return rc;
+			dev_exception_clean(devcgroup);
 			rc = dev_exceptions_copy(&devcgroup->exceptions,
 						 &parent->exceptions);
-			if (rc)
+			if (rc) {
+				dev_exceptions_move(&devcgroup->exceptions,
+						    &tmp_devcgrp.exceptions);
 				return rc;
+			}
+			devcgroup->behavior = DEVCG_DEFAULT_ALLOW;
+			dev_exception_clean(&tmp_devcgrp);
 			break;
 		case DEVCG_DENY:
 			if (css_has_online_children(&devcgroup->css))
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/digsig.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/digsig.c
@@ -122,6 +122,7 @@
 {
 	struct key_restriction *restriction;
 	key_perm_t perm;
+	int ret;
 
 	perm = (KEY_POS_ALL & ~KEY_POS_SETATTR) | KEY_USR_VIEW
 		| KEY_USR_READ | KEY_USR_SEARCH;
@@ -142,7 +143,10 @@
 	perm |= KEY_USR_WRITE;
 
 out:
-	return __integrity_init_keyring(id, perm, restriction);
+	ret = __integrity_init_keyring(id, perm, restriction);
+	if (ret)
+		kfree(restriction);
+	return ret;
 }
 
 static int __init integrity_add_key(const unsigned int id, const void *data,
@@ -180,7 +184,7 @@
 	rc = kernel_read_file_from_path(path, 0, &data, INT_MAX, NULL,
 					READING_X509_CERTIFICATE);
 	if (rc < 0) {
-		pr_err("Unable to open file: %s (%d)", path, rc);
+		pr_warn("Unable to open file: %s (%d)", path, rc);
 		return rc;
 	}
 	size = rc;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/digsig_asymmetric.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/digsig_asymmetric.c
@@ -109,22 +109,25 @@
 
 	pk = asymmetric_key_public_key(key);
 	pks.pkey_algo = pk->pkey_algo;
-	if (!strcmp(pk->pkey_algo, "rsa"))
+	if (!strcmp(pk->pkey_algo, "rsa")) {
 		pks.encoding = "pkcs1";
-	else if (!strncmp(pk->pkey_algo, "ecdsa-", 6))
+	} else if (!strncmp(pk->pkey_algo, "ecdsa-", 6)) {
 		/* edcsa-nist-p192 etc. */
 		pks.encoding = "x962";
-	else if (!strcmp(pk->pkey_algo, "ecrdsa") ||
-		   !strcmp(pk->pkey_algo, "sm2"))
+	} else if (!strcmp(pk->pkey_algo, "ecrdsa") ||
+		   !strcmp(pk->pkey_algo, "sm2")) {
 		pks.encoding = "raw";
-	else
-		return -ENOPKG;
+	} else {
+		ret = -ENOPKG;
+		goto out;
+	}
 
 	pks.digest = (u8 *)data;
 	pks.digest_size = datalen;
 	pks.s = hdr->sig;
 	pks.s_size = siglen;
 	ret = verify_signature(key, &pks);
+out:
 	key_put(key);
 	pr_debug("%s() = %d\n", __func__, ret);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/evm/evm_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/evm/evm_crypto.c
@@ -40,7 +40,7 @@
 /**
  * evm_set_key() - set EVM HMAC key from the kernel
  * @key: pointer to a buffer with the key data
- * @size: length of the key data
+ * @keylen: length of the key data
  *
  * This function allows setting the EVM HMAC key from the kernel
  * without using the "encrypted" key subsystem keys. It can be used
@@ -75,7 +75,7 @@
 {
 	long rc;
 	const char *algo;
-	struct crypto_shash **tfm, *tmp_tfm = NULL;
+	struct crypto_shash **tfm, *tmp_tfm;
 	struct shash_desc *desc;
 
 	if (type == EVM_XATTR_HMAC) {
@@ -120,16 +120,13 @@
 alloc:
 	desc = kmalloc(sizeof(*desc) + crypto_shash_descsize(*tfm),
 			GFP_KERNEL);
-	if (!desc) {
-		crypto_free_shash(tmp_tfm);
+	if (!desc)
 		return ERR_PTR(-ENOMEM);
-	}
 
 	desc->tfm = *tfm;
 
 	rc = crypto_shash_init(desc);
 	if (rc) {
-		crypto_free_shash(tmp_tfm);
 		kfree(desc);
 		return ERR_PTR(rc);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/evm/evm_main.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/evm/evm_main.c
@@ -78,7 +78,7 @@
 
 LIST_HEAD(evm_config_xattrnames);
 
-static int evm_fixmode;
+static int evm_fixmode __ro_after_init;
 static int __init evm_set_fixmode(char *str)
 {
 	if (strncmp(str, "fix", 3) == 0)
@@ -86,7 +86,7 @@
 	else
 		pr_err("invalid \"%s\" mode", str);
 
-	return 0;
+	return 1;
 }
 __setup("evm=", evm_set_fixmode);
 
@@ -324,7 +324,6 @@
 /**
  * evm_read_protected_xattrs - read EVM protected xattr names, lengths, values
  * @dentry: dentry of the read xattrs
- * @inode: inode of the read xattrs
  * @buffer: buffer xattr names, lengths or values are copied to
  * @buffer_size: size of buffer
  * @type: n: names, l: lengths, v: values
@@ -396,6 +395,7 @@
  * @xattr_name: requested xattr
  * @xattr_value: requested xattr value
  * @xattr_value_len: requested xattr value length
+ * @iint: inode integrity metadata
  *
  * Calculate the HMAC for the given dentry and verify it against the stored
  * security.evm xattr. For performance, use the xattr value and length
@@ -770,7 +770,9 @@
 
 /**
  * evm_inode_setattr - prevent updating an invalid EVM extended attribute
+ * @idmap: idmap of the mount
  * @dentry: pointer to the affected dentry
+ * @attr: iattr structure containing the new file attributes
  *
  * Permit update of file attributes when files have a valid EVM signature,
  * except in the case of them having an immutable portable signature.
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/iint.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/iint.c
@@ -43,12 +43,10 @@
 		else if (inode > iint->inode)
 			n = n->rb_right;
 		else
-			break;
+			return iint;
 	}
-	if (!n)
-		return NULL;
 
-	return iint;
+	return NULL;
 }
 
 /*
@@ -68,9 +66,32 @@
 	return iint;
 }
 
-static void iint_free(struct integrity_iint_cache *iint)
+#define IMA_MAX_NESTING (FILESYSTEM_MAX_STACK_DEPTH+1)
+
+/*
+ * It is not clear that IMA should be nested at all, but as long is it measures
+ * files both on overlayfs and on underlying fs, we need to annotate the iint
+ * mutex to avoid lockdep false positives related to IMA + overlayfs.
+ * See ovl_lockdep_annotate_inode_mutex_key() for more details.
+ */
+static inline void iint_lockdep_annotate(struct integrity_iint_cache *iint,
+					 struct inode *inode)
+{
+#ifdef CONFIG_LOCKDEP
+	static struct lock_class_key iint_mutex_key[IMA_MAX_NESTING];
+
+	int depth = inode->i_sb->s_stack_depth;
+
+	if (WARN_ON_ONCE(depth < 0 || depth >= IMA_MAX_NESTING))
+		depth = 0;
+
+	lockdep_set_class(&iint->mutex, &iint_mutex_key[depth]);
+#endif
+}
+
+static void iint_init_always(struct integrity_iint_cache *iint,
+			     struct inode *inode)
 {
-	kfree(iint->ima_hash);
 	iint->ima_hash = NULL;
 	iint->version = 0;
 	iint->flags = 0UL;
@@ -82,6 +103,14 @@
 	iint->ima_creds_status = INTEGRITY_UNKNOWN;
 	iint->evm_status = INTEGRITY_UNKNOWN;
 	iint->measured_pcrs = 0;
+	mutex_init(&iint->mutex);
+	iint_lockdep_annotate(iint, inode);
+}
+
+static void iint_free(struct integrity_iint_cache *iint)
+{
+	kfree(iint->ima_hash);
+	mutex_destroy(&iint->mutex);
 	kmem_cache_free(iint_cache, iint);
 }
 
@@ -114,6 +143,8 @@
 	if (!iint)
 		return NULL;
 
+	iint_init_always(iint, inode);
+
 	write_lock(&integrity_iint_lock);
 
 	p = &integrity_iint_tree.rb_node;
@@ -121,10 +152,15 @@
 		parent = *p;
 		test_iint = rb_entry(parent, struct integrity_iint_cache,
 				     rb_node);
-		if (inode < test_iint->inode)
+		if (inode < test_iint->inode) {
 			p = &(*p)->rb_left;
-		else
+		} else if (inode > test_iint->inode) {
 			p = &(*p)->rb_right;
+		} else {
+			write_unlock(&integrity_iint_lock);
+			kmem_cache_free(iint_cache, iint);
+			return test_iint;
+		}
 	}
 
 	iint->inode = inode;
@@ -158,25 +194,18 @@
 	iint_free(iint);
 }
 
-static void init_once(void *foo)
+static void iint_init_once(void *foo)
 {
 	struct integrity_iint_cache *iint = (struct integrity_iint_cache *) foo;
 
 	memset(iint, 0, sizeof(*iint));
-	iint->ima_file_status = INTEGRITY_UNKNOWN;
-	iint->ima_mmap_status = INTEGRITY_UNKNOWN;
-	iint->ima_bprm_status = INTEGRITY_UNKNOWN;
-	iint->ima_read_status = INTEGRITY_UNKNOWN;
-	iint->ima_creds_status = INTEGRITY_UNKNOWN;
-	iint->evm_status = INTEGRITY_UNKNOWN;
-	mutex_init(&iint->mutex);
 }
 
 static int __init integrity_iintcache_init(void)
 {
 	iint_cache =
 	    kmem_cache_create("iint_cache", sizeof(struct integrity_iint_cache),
-			      0, SLAB_PANIC, init_once);
+			      0, SLAB_PANIC, iint_init_once);
 	return 0;
 }
 DEFINE_LSM(integrity) = {
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/Kconfig
@@ -8,7 +8,7 @@
 	select CRYPTO_HMAC
 	select CRYPTO_SHA1
 	select CRYPTO_HASH_INFO
-	select TCG_TPM if HAS_IOMEM && !UML
+	select TCG_TPM if HAS_IOMEM
 	select TCG_TIS if TCG_TPM && X86
 	select TCG_CRB if TCG_TPM && ACPI
 	select TCG_IBMVTPM if TCG_TPM && PPC_PSERIES
@@ -29,9 +29,11 @@
 	  to learn more about IMA.
 	  If unsure, say N.
 
+if IMA
+
 config IMA_KEXEC
 	bool "Enable carrying the IMA measurement list across a soft boot"
-	depends on IMA && TCG_TPM && HAVE_IMA_KEXEC
+	depends on TCG_TPM && HAVE_IMA_KEXEC
 	default n
 	help
 	   TPM PCRs are only reset on a hard reboot.  In order to validate
@@ -43,7 +45,6 @@
 
 config IMA_MEASURE_PCR_IDX
 	int
-	depends on IMA
 	range 8 14
 	default 10
 	help
@@ -53,7 +54,7 @@
 
 config IMA_LSM_RULES
 	bool
-	depends on IMA && AUDIT && (SECURITY_SELINUX || SECURITY_SMACK || SECURITY_APPARMOR)
+	depends on AUDIT && (SECURITY_SELINUX || SECURITY_SMACK || SECURITY_APPARMOR)
 	default y
 	help
 	  Disabling this option will disregard LSM based policy rules.
@@ -61,7 +62,6 @@
 choice
 	prompt "Default template"
 	default IMA_NG_TEMPLATE
-	depends on IMA
 	help
 	  Select the default IMA measurement template.
 
@@ -69,10 +69,9 @@
 	  hash, defined as 20 bytes, and a null terminated pathname,
 	  limited to 255 characters.  The 'ima-ng' measurement list
 	  template permits both larger hash digests and longer
-	  pathnames.
+	  pathnames. The configured default template can be replaced
+	  by specifying "ima_template=" on the boot command line.
 
-	config IMA_TEMPLATE
-		bool "ima"
 	config IMA_NG_TEMPLATE
 		bool "ima-ng (default)"
 	config IMA_SIG_TEMPLATE
@@ -81,15 +80,12 @@
 
 config IMA_DEFAULT_TEMPLATE
 	string
-	depends on IMA
-	default "ima" if IMA_TEMPLATE
 	default "ima-ng" if IMA_NG_TEMPLATE
 	default "ima-sig" if IMA_SIG_TEMPLATE
 
 choice
 	prompt "Default integrity hash algorithm"
 	default IMA_DEFAULT_HASH_SHA1
-	depends on IMA
 	help
 	   Select the default hash algorithm used for the measurement
 	   list, integrity appraisal and audit log.  The compiled default
@@ -102,24 +98,23 @@
 
 	config IMA_DEFAULT_HASH_SHA256
 		bool "SHA256"
-		depends on CRYPTO_SHA256=y && !IMA_TEMPLATE
+		depends on CRYPTO_SHA256=y
 
 	config IMA_DEFAULT_HASH_SHA512
 		bool "SHA512"
-		depends on CRYPTO_SHA512=y && !IMA_TEMPLATE
+		depends on CRYPTO_SHA512=y
 
 	config IMA_DEFAULT_HASH_WP512
 		bool "WP512"
-		depends on CRYPTO_WP512=y && !IMA_TEMPLATE
+		depends on CRYPTO_WP512=y
 
 	config IMA_DEFAULT_HASH_SM3
 		bool "SM3"
-		depends on CRYPTO_SM3=y && !IMA_TEMPLATE
+		depends on CRYPTO_SM3=y
 endchoice
 
 config IMA_DEFAULT_HASH
 	string
-	depends on IMA
 	default "sha1" if IMA_DEFAULT_HASH_SHA1
 	default "sha256" if IMA_DEFAULT_HASH_SHA256
 	default "sha512" if IMA_DEFAULT_HASH_SHA512
@@ -128,7 +123,6 @@
 
 config IMA_WRITE_POLICY
 	bool "Enable multiple writes to the IMA policy"
-	depends on IMA
 	default n
 	help
 	  IMA policy can now be updated multiple times.  The new rules get
@@ -139,7 +133,6 @@
 
 config IMA_READ_POLICY
 	bool "Enable reading back the current IMA policy"
-	depends on IMA
 	default y if IMA_WRITE_POLICY
 	default n if !IMA_WRITE_POLICY
 	help
@@ -149,7 +142,6 @@
 
 config IMA_APPRAISE
 	bool "Appraise integrity measurements"
-	depends on IMA
 	default n
 	help
 	  This option enables local measurement integrity appraisal.
@@ -250,18 +242,6 @@
 	   The modsig keyword can be used in the IMA policy to allow a hook
 	   to accept such signatures.
 
-config IMA_TRUSTED_KEYRING
-	bool "Require all keys on the .ima keyring be signed (deprecated)"
-	depends on IMA_APPRAISE && SYSTEM_TRUSTED_KEYRING
-	depends on INTEGRITY_ASYMMETRIC_KEYS
-	select INTEGRITY_TRUSTED_KEYRING
-	default y
-	help
-	   This option requires that all keys added to the .ima
-	   keyring be signed by a key on the system trusted keyring.
-
-	   This option is deprecated in favor of INTEGRITY_TRUSTED_KEYRING
-
 config IMA_KEYRINGS_PERMIT_SIGNED_BY_BUILTIN_OR_SECONDARY
 	bool "Permit keys validly signed by a built-in or secondary CA cert (EXPERIMENTAL)"
 	depends on SYSTEM_TRUSTED_KEYRING
@@ -282,7 +262,7 @@
 config IMA_BLACKLIST_KEYRING
 	bool "Create IMA machine owner blacklist keyrings (EXPERIMENTAL)"
 	depends on SYSTEM_TRUSTED_KEYRING
-	depends on IMA_TRUSTED_KEYRING
+	depends on INTEGRITY_TRUSTED_KEYRING
 	default n
 	help
 	   This option creates an IMA blacklist keyring, which contains all
@@ -292,7 +272,7 @@
 
 config IMA_LOAD_X509
 	bool "Load X509 certificate onto the '.ima' trusted keyring"
-	depends on IMA_TRUSTED_KEYRING
+	depends on INTEGRITY_TRUSTED_KEYRING
 	default n
 	help
 	   File signature verification is based on the public keys
@@ -317,7 +297,6 @@
 
 config IMA_MEASURE_ASYMMETRIC_KEYS
 	bool
-	depends on IMA
 	depends on ASYMMETRIC_PUBLIC_KEY_SUBTYPE=y
 	default y
 
@@ -336,7 +315,8 @@
 
 config IMA_DISABLE_HTABLE
 	bool "Disable htable to allow measurement of duplicate records"
-	depends on IMA
 	default n
 	help
 	   This option disables htable to allow measurement of duplicate records.
+
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima.h
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima.h
@@ -122,7 +122,7 @@
 extern const int read_idmap[];
 
 #ifdef CONFIG_HAVE_IMA_KEXEC
-void ima_load_kexec_buffer(void);
+void __init ima_load_kexec_buffer(void);
 #else
 static inline void ima_load_kexec_buffer(void) {}
 #endif /* CONFIG_HAVE_IMA_KEXEC */
@@ -255,7 +255,7 @@
 
 /* LIM API function definitions */
 int ima_get_action(struct user_namespace *mnt_userns, struct inode *inode,
-		   const struct cred *cred, u32 secid, int mask,
+		   const struct cred *cred, struct lsmblob *blob, int mask,
 		   enum ima_hooks func, int *pcr,
 		   struct ima_template_desc **template_desc,
 		   const char *func_data, unsigned int *allowed_algos);
@@ -286,8 +286,8 @@
 
 /* IMA policy related functions */
 int ima_match_policy(struct user_namespace *mnt_userns, struct inode *inode,
-		     const struct cred *cred, u32 secid, enum ima_hooks func,
-		     int mask, int flags, int *pcr,
+		     const struct cred *cred, struct lsmblob *blob,
+		     enum ima_hooks func, int mask, int flags, int *pcr,
 		     struct ima_template_desc **template_desc,
 		     const char *func_data, unsigned int *allowed_algos);
 void ima_init_policy(void);
@@ -428,7 +428,7 @@
 #else
 
 static inline int ima_filter_rule_init(u32 field, u32 op, char *rulestr,
-				       void **lsmrule)
+				       void **lsmrule, gfp_t gfp)
 {
 	return -EINVAL;
 }
@@ -437,7 +437,7 @@
 {
 }
 
-static inline int ima_filter_rule_match(u32 secid, u32 field, u32 op,
+static inline int ima_filter_rule_match(struct lsmblob *blob, u32 field, u32 op,
 					void *lsmrule)
 {
 	return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_api.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_api.c
@@ -165,7 +165,7 @@
  * @mnt_userns:	user namespace of the mount the inode was found from
  * @inode: pointer to the inode associated with the object being validated
  * @cred: pointer to credentials structure to validate
- * @secid: secid of the task being validated
+ * @blob: LSM data of the task being validated
  * @mask: contains the permission mask (MAY_READ, MAY_WRITE, MAY_EXEC,
  *        MAY_APPEND)
  * @func: caller identifier
@@ -186,7 +186,7 @@
  *
  */
 int ima_get_action(struct user_namespace *mnt_userns, struct inode *inode,
-		   const struct cred *cred, u32 secid, int mask,
+		   const struct cred *cred, struct lsmblob *blob, int mask,
 		   enum ima_hooks func, int *pcr,
 		   struct ima_template_desc **template_desc,
 		   const char *func_data, unsigned int *allowed_algos)
@@ -195,7 +195,7 @@
 
 	flags &= ima_policy_flag;
 
-	return ima_match_policy(mnt_userns, inode, cred, secid, func, mask,
+	return ima_match_policy(mnt_userns, inode, cred, blob, func, mask,
 				flags, pcr, template_desc, func_data,
 				allowed_algos);
 }
@@ -216,7 +216,8 @@
 {
 	const char *audit_cause = "failed";
 	struct inode *inode = file_inode(file);
-	const char *filename = file->f_path.dentry->d_name.name;
+	struct inode *real_inode = d_real_inode(file_dentry(file));
+	struct name_snapshot filename;
 	int result = 0;
 	int length;
 	void *tmpbuf;
@@ -266,6 +267,10 @@
 	iint->ima_hash = tmpbuf;
 	memcpy(iint->ima_hash, &hash, length);
 	iint->version = i_version;
+	if (real_inode != inode) {
+		iint->real_ino = real_inode->i_ino;
+		iint->real_dev = real_inode->i_sb->s_dev;
+	}
 
 	/* Possibly temporary failure due to type of read (eg. O_DIRECT) */
 	if (!result)
@@ -275,9 +280,13 @@
 		if (file->f_flags & O_DIRECT)
 			audit_cause = "failed(directio)";
 
+		take_dentry_name_snapshot(&filename, file->f_path.dentry);
+
 		integrity_audit_msg(AUDIT_INTEGRITY_DATA, inode,
-				    filename, "collect_data", audit_cause,
-				    result, 0);
+				    filename.name.name, "collect_data",
+				    audit_cause, result, 0);
+
+		release_dentry_name_snapshot(&filename);
 	}
 	return result;
 }
@@ -390,6 +399,7 @@
  */
 const char *ima_d_path(const struct path *path, char **pathbuf, char *namebuf)
 {
+	struct name_snapshot filename;
 	char *pathname = NULL;
 
 	*pathbuf = __getname();
@@ -403,7 +413,10 @@
 	}
 
 	if (!pathname) {
-		strlcpy(namebuf, path->dentry->d_name.name, NAME_MAX);
+		take_dentry_name_snapshot(&filename, path->dentry);
+		strlcpy(namebuf, filename.name.name, NAME_MAX);
+		release_dentry_name_snapshot(&filename);
+
 		pathname = namebuf;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_appraise.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_appraise.c
@@ -71,15 +71,15 @@
 int ima_must_appraise(struct user_namespace *mnt_userns, struct inode *inode,
 		      int mask, enum ima_hooks func)
 {
-	u32 secid;
+	struct lsmblob blob;
 
 	if (!ima_appraise)
 		return 0;
 
-	security_task_getsecid_subj(current, &secid);
-	return ima_match_policy(mnt_userns, inode, current_cred(), secid,
-				func, mask, IMA_APPRAISE | IMA_HASH, NULL,
-				NULL, NULL, NULL);
+	security_task_getsecid_subj(current, &blob);
+	return ima_match_policy(mnt_userns, inode, current_cred(), &blob,
+				func, mask, IMA_APPRAISE | IMA_HASH, NULL, NULL,
+				NULL, NULL);
 }
 
 static int ima_fix_xattr(struct dentry *dentry,
@@ -408,7 +408,8 @@
 		goto out;
 	}
 
-	status = evm_verifyxattr(dentry, XATTR_NAME_IMA, xattr_value, rc, iint);
+	status = evm_verifyxattr(dentry, XATTR_NAME_IMA, xattr_value,
+				 rc < 0 ? 0 : rc, iint);
 	switch (status) {
 	case INTEGRITY_PASS:
 	case INTEGRITY_PASS_IMMUTABLE:
@@ -643,22 +644,26 @@
 	const struct evm_ima_xattr_data *xvalue = xattr_value;
 	int digsig = 0;
 	int result;
+	int err;
 
 	result = ima_protect_xattr(dentry, xattr_name, xattr_value,
 				   xattr_value_len);
 	if (result == 1) {
 		if (!xattr_value_len || (xvalue->type >= IMA_XATTR_LAST))
 			return -EINVAL;
+
+		err = validate_hash_algo(dentry, xvalue, xattr_value_len);
+		if (err)
+			return err;
+
 		digsig = (xvalue->type == EVM_IMA_XATTR_DIGSIG);
 	} else if (!strcmp(xattr_name, XATTR_NAME_EVM) && xattr_value_len > 0) {
 		digsig = (xvalue->type == EVM_XATTR_PORTABLE_DIGSIG);
 	}
 	if (result == 1 || evm_revalidate_status(xattr_name)) {
-		result = validate_hash_algo(dentry, xvalue, xattr_value_len);
-		if (result)
-			return result;
-
 		ima_reset_appraise_flags(d_backing_inode(dentry), digsig);
+		if (result == 1)
+			result = 0;
 	}
 	return result;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_crypto.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_crypto.c
@@ -205,6 +205,7 @@
 
 		crypto_free_shash(ima_algo_array[i].tfm);
 	}
+	kfree(ima_algo_array);
 out:
 	crypto_free_shash(ima_shash_tfm);
 	return rc;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_efi.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_efi.c
@@ -67,6 +67,8 @@
 	if (IS_ENABLED(CONFIG_IMA_ARCH_POLICY) && arch_ima_get_secureboot()) {
 		if (IS_ENABLED(CONFIG_MODULE_SIG))
 			set_module_sig_enforced();
+		if (IS_ENABLED(CONFIG_KEXEC_SIG))
+			set_kexec_sig_enforced();
 		return sb_arch_rules;
 	}
 	return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_fs.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_fs.c
@@ -287,7 +287,7 @@
 	rc = kernel_read_file_from_path(path, 0, &data, INT_MAX, NULL,
 					READING_POLICY);
 	if (rc < 0) {
-		pr_err("Unable to open file: %s (%d)", path, rc);
+		pr_warn("Unable to open file: %s (%d)", path, rc);
 		return rc;
 	}
 	size = rc;
@@ -496,12 +496,12 @@
 
 	return 0;
 out:
+	securityfs_remove(ima_policy);
 	securityfs_remove(violations);
 	securityfs_remove(runtime_measurements_count);
 	securityfs_remove(ascii_runtime_measurements);
 	securityfs_remove(binary_runtime_measurements);
 	securityfs_remove(ima_symlink);
 	securityfs_remove(ima_dir);
-	securityfs_remove(ima_policy);
 	return -1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_kexec.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_kexec.c
@@ -137,7 +137,7 @@
 /*
  * Restore the measurement list from the previous kernel.
  */
-void ima_load_kexec_buffer(void)
+void __init ima_load_kexec_buffer(void)
 {
 	void *kexec_buffer = NULL;
 	size_t kexec_buffer_size = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_main.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_main.c
@@ -26,6 +26,7 @@
 #include <linux/ima.h>
 #include <linux/iversion.h>
 #include <linux/fs.h>
+#include <linux/iversion.h>
 
 #include "ima.h"
 
@@ -199,10 +200,10 @@
 }
 
 static int process_measurement(struct file *file, const struct cred *cred,
-			       u32 secid, char *buf, loff_t size, int mask,
-			       enum ima_hooks func)
+			       struct lsmblob *blob, char *buf, loff_t size,
+			       int mask, enum ima_hooks func)
 {
-	struct inode *inode = file_inode(file);
+	struct inode *backing_inode, *inode = file_inode(file);
 	struct integrity_iint_cache *iint = NULL;
 	struct ima_template_desc *template_desc = NULL;
 	char *pathbuf = NULL;
@@ -224,7 +225,7 @@
 	 * bitmask based on the appraise/audit/measurement policy.
 	 * Included is the appraise submask.
 	 */
-	action = ima_get_action(file_mnt_user_ns(file), inode, cred, secid,
+	action = ima_get_action(file_mnt_user_ns(file), inode, cred, blob,
 				mask, func, &pcr, &template_desc, NULL,
 				&allowed_algos);
 	violation_check = ((func == FILE_CHECK || func == MMAP_CHECK) &&
@@ -278,6 +279,19 @@
 		iint->measured_pcrs = 0;
 	}
 
+	/* Detect and re-evaluate changes made to the backing file. */
+	backing_inode = d_real_inode(file_dentry(file));
+	if (backing_inode != inode &&
+	    (action & IMA_DO_MASK) && (iint->flags & IMA_DONE_MASK)) {
+		if (!IS_I_VERSION(backing_inode) ||
+		    backing_inode->i_sb->s_dev != iint->real_dev ||
+		    backing_inode->i_ino != iint->real_ino ||
+		    !inode_eq_iversion(backing_inode, iint->version)) {
+			iint->flags &= ~IMA_DONE_MASK;
+			iint->measured_pcrs = 0;
+		}
+	}
+
 	/* Determine if already appraised/measured based on bitmask
 	 * (IMA_MEASURE, IMA_MEASURED, IMA_XXXX_APPRAISE, IMA_XXXX_APPRAISED,
 	 *  IMA_AUDIT, IMA_AUDITED)
@@ -395,7 +409,9 @@
 /**
  * ima_file_mmap - based on policy, collect/store measurement.
  * @file: pointer to the file to be measured (May be NULL)
- * @prot: contains the protection that will be applied by the kernel.
+ * @reqprot: protection requested by the application
+ * @prot: protection that will be applied by the kernel
+ * @flags: operational flags
  *
  * Measure files being mmapped executable based on the ima_must_measure()
  * policy decision.
@@ -403,14 +419,15 @@
  * On success return 0.  On integrity appraisal error, assuming the file
  * is in policy and IMA-appraisal is in enforcing mode, return -EACCES.
  */
-int ima_file_mmap(struct file *file, unsigned long prot)
+int ima_file_mmap(struct file *file, unsigned long reqprot,
+		  unsigned long prot, unsigned long flags)
 {
-	u32 secid;
+	struct lsmblob blob;
 
 	if (file && (prot & PROT_EXEC)) {
-		security_task_getsecid_subj(current, &secid);
-		return process_measurement(file, current_cred(), secid, NULL,
-					   0, MAY_EXEC, MMAP_CHECK);
+		security_task_getsecid_subj(current, &blob);
+		return process_measurement(file, current_cred(), &blob,
+					   NULL, 0, MAY_EXEC, MMAP_CHECK);
 	}
 
 	return 0;
@@ -436,9 +453,9 @@
 	char *pathbuf = NULL;
 	const char *pathname = NULL;
 	struct inode *inode;
+	struct lsmblob blob;
 	int result = 0;
 	int action;
-	u32 secid;
 	int pcr;
 
 	/* Is mprotect making an mmap'ed file executable? */
@@ -446,11 +463,11 @@
 	    !(prot & PROT_EXEC) || (vma->vm_flags & VM_EXEC))
 		return 0;
 
-	security_task_getsecid_subj(current, &secid);
+	security_task_getsecid_subj(current, &blob);
 	inode = file_inode(vma->vm_file);
-	action = ima_get_action(file_mnt_user_ns(vma->vm_file), inode,
-				current_cred(), secid, MAY_EXEC, MMAP_CHECK,
-				&pcr, &template, NULL, NULL);
+	action = ima_get_action(file_mnt_user_ns(vma->vm_file), NULL,
+				current_cred(), &blob, 0,
+				MMAP_CHECK, &pcr, &template, NULL, NULL);
 
 	/* Is the mmap'ed file in policy? */
 	if (!(action & (IMA_MEASURE | IMA_APPRAISE_SUBMASK)))
@@ -485,16 +502,16 @@
 int ima_bprm_check(struct linux_binprm *bprm)
 {
 	int ret;
-	u32 secid;
+	struct lsmblob blob;
 
-	security_task_getsecid_subj(current, &secid);
-	ret = process_measurement(bprm->file, current_cred(), secid, NULL, 0,
+	security_task_getsecid_subj(current, &blob);
+	ret = process_measurement(bprm->file, current_cred(), &blob, NULL, 0,
 				  MAY_EXEC, BPRM_CHECK);
 	if (ret)
 		return ret;
 
-	security_cred_getsecid(bprm->cred, &secid);
-	return process_measurement(bprm->file, bprm->cred, secid, NULL, 0,
+	security_cred_getsecid(bprm->cred, &blob);
+	return process_measurement(bprm->file, bprm->cred, &blob, NULL, 0,
 				   MAY_EXEC, CREDS_CHECK);
 }
 
@@ -510,10 +527,10 @@
  */
 int ima_file_check(struct file *file, int mask)
 {
-	u32 secid;
+	struct lsmblob blob;
 
-	security_task_getsecid_subj(current, &secid);
-	return process_measurement(file, current_cred(), secid, NULL, 0,
+	security_task_getsecid_subj(current, &blob);
+	return process_measurement(file, current_cred(), &blob, NULL, 0,
 				   mask & (MAY_READ | MAY_WRITE | MAY_EXEC |
 					   MAY_APPEND), FILE_CHECK);
 }
@@ -689,7 +706,7 @@
 		  bool contents)
 {
 	enum ima_hooks func;
-	u32 secid;
+	struct lsmblob blob;
 
 	/*
 	 * Do devices using pre-allocated memory run the risk of the
@@ -709,8 +726,8 @@
 
 	/* Read entire file for all partial reads. */
 	func = read_idmap[read_id] ?: FILE_CHECK;
-	security_task_getsecid_subj(current, &secid);
-	return process_measurement(file, current_cred(), secid, NULL,
+	security_task_getsecid_subj(current, &blob);
+	return process_measurement(file, current_cred(), &blob, NULL,
 				   0, MAY_READ, func);
 }
 
@@ -739,7 +756,7 @@
 		       enum kernel_read_file_id read_id)
 {
 	enum ima_hooks func;
-	u32 secid;
+	struct lsmblob blob;
 
 	/* permit signed certs */
 	if (!file && read_id == READING_X509_CERTIFICATE)
@@ -752,8 +769,8 @@
 	}
 
 	func = read_idmap[read_id] ?: FILE_CHECK;
-	security_task_getsecid_subj(current, &secid);
-	return process_measurement(file, current_cred(), secid, buf, size,
+	security_task_getsecid_subj(current, &blob);
+	return process_measurement(file, current_cred(), &blob, buf, size,
 				   MAY_READ, func);
 }
 
@@ -882,7 +899,7 @@
 	int digest_hash_len = hash_digest_size[ima_hash_algo];
 	int violation = 0;
 	int action = 0;
-	u32 secid;
+	struct lsmblob blob;
 
 	if (digest && digest_len < digest_hash_len)
 		return -EINVAL;
@@ -905,9 +922,9 @@
 	 * buffer measurements.
 	 */
 	if (func) {
-		security_task_getsecid_subj(current, &secid);
+		security_task_getsecid_subj(current, &blob);
 		action = ima_get_action(mnt_userns, inode, current_cred(),
-					secid, 0, func, &pcr, &template,
+					&blob, 0, func, &pcr, &template,
 					func_data, NULL);
 		if (!(action & IMA_MEASURE) && !digest)
 			return -ENOENT;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_modsig.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_modsig.c
@@ -89,6 +89,9 @@
 
 /**
  * ima_collect_modsig - Calculate the file hash without the appended signature.
+ * @modsig: parsed module signature
+ * @buf: data to verify the signature on
+ * @size: data size
  *
  * Since the modsig is part of the file contents, the hash used in its signature
  * isn't the same one ordinarily calculated by IMA. Therefore PKCS7 code
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_policy.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_policy.c
@@ -84,7 +84,7 @@
 	int pcr;
 	unsigned int allowed_algos; /* bitfield of allowed hash algorithms */
 	struct {
-		void *rule;	/* LSM file metadata specific */
+		void *rules[LSMBLOB_ENTRIES]; /* LSM file metadata specific */
 		char *args_p;	/* audit value */
 		int type;	/* audit type */
 	} lsm[MAX_LSM_RULES];
@@ -94,6 +94,22 @@
 	struct ima_template_desc *template;
 };
 
+/**
+ * ima_lsm_isset - Is a rule set for any of the active security modules
+ * @rules: The set of IMA rules to check.
+ *
+ * If a rule is set for any LSM return true, otherwise return false.
+ */
+static inline bool ima_lsm_isset(void *rules[])
+{
+	int i;
+
+	for (i = 0; i < LSMBLOB_ENTRIES; i++)
+		if (rules[i])
+			return true;
+	return false;
+}
+
 /*
  * sanity check in case the kernels gains more hash algorithms that can
  * fit in an unsigned int
@@ -228,7 +244,7 @@
 static LIST_HEAD(ima_default_rules);
 static LIST_HEAD(ima_policy_rules);
 static LIST_HEAD(ima_temp_rules);
-static struct list_head *ima_rules = &ima_default_rules;
+static struct list_head __rcu *ima_rules = (struct list_head __rcu *)(&ima_default_rules);
 
 static int ima_policy __initdata;
 
@@ -347,9 +363,11 @@
 static void ima_lsm_free_rule(struct ima_rule_entry *entry)
 {
 	int i;
+	int r;
 
 	for (i = 0; i < MAX_LSM_RULES; i++) {
-		ima_filter_rule_free(entry->lsm[i].rule);
+		for (r = 0; r < LSMBLOB_ENTRIES; r++)
+			ima_filter_rule_free(entry->lsm[i].rules);
 		kfree(entry->lsm[i].args_p);
 	}
 }
@@ -370,7 +388,8 @@
 	kfree(entry);
 }
 
-static struct ima_rule_entry *ima_lsm_copy_rule(struct ima_rule_entry *entry)
+static struct ima_rule_entry *ima_lsm_copy_rule(struct ima_rule_entry *entry,
+						gfp_t gfp)
 {
 	struct ima_rule_entry *nentry;
 	int i;
@@ -379,7 +398,7 @@
 	 * Immutable elements are copied over as pointers and data; only
 	 * lsm rules can change
 	 */
-	nentry = kmemdup(entry, sizeof(*nentry), GFP_KERNEL);
+	nentry = kmemdup(entry, sizeof(*nentry), gfp);
 	if (!nentry)
 		return NULL;
 
@@ -400,8 +419,9 @@
 
 		ima_filter_rule_init(nentry->lsm[i].type, Audit_equal,
 				     nentry->lsm[i].args_p,
-				     &nentry->lsm[i].rule);
-		if (!nentry->lsm[i].rule)
+				     &nentry->lsm[i].rules[0],
+				     gfp);
+		if (!ima_lsm_isset(nentry->lsm[i].rules))
 			pr_warn("rule for LSM \'%s\' is undefined\n",
 				nentry->lsm[i].args_p);
 	}
@@ -412,7 +432,7 @@
 {
 	struct ima_rule_entry *nentry;
 
-	nentry = ima_lsm_copy_rule(entry);
+	nentry = ima_lsm_copy_rule(entry, GFP_KERNEL);
 	if (!nentry)
 		return -ENOMEM;
 
@@ -528,7 +548,7 @@
  * @mnt_userns:	user namespace of the mount the inode was found from
  * @inode: a pointer to an inode
  * @cred: a pointer to a credentials structure for user validation
- * @secid: the secid of the task to be validated
+ * @blob: the lsm data of the task to be validated
  * @func: LIM hook identifier
  * @mask: requested action (MAY_READ | MAY_WRITE | MAY_APPEND | MAY_EXEC)
  * @func_data: func specific data, may be NULL
@@ -538,7 +558,7 @@
 static bool ima_match_rules(struct ima_rule_entry *rule,
 			    struct user_namespace *mnt_userns,
 			    struct inode *inode, const struct cred *cred,
-			    u32 secid, enum ima_hooks func, int mask,
+			    struct lsmblob *blob, enum ima_hooks func, int mask,
 			    const char *func_data)
 {
 	int i;
@@ -588,9 +608,9 @@
 		return false;
 	for (i = 0; i < MAX_LSM_RULES; i++) {
 		int rc = 0;
-		u32 osid;
+		struct lsmblob lsmdata;
 
-		if (!rule->lsm[i].rule) {
+		if (!ima_lsm_isset(rule->lsm[i].rules)) {
 			if (!rule->lsm[i].args_p)
 				continue;
 			else
@@ -600,17 +620,17 @@
 		case LSM_OBJ_USER:
 		case LSM_OBJ_ROLE:
 		case LSM_OBJ_TYPE:
-			security_inode_getsecid(inode, &osid);
-			rc = ima_filter_rule_match(osid, rule->lsm[i].type,
+			security_inode_getsecid(inode, &lsmdata);
+			rc = ima_filter_rule_match(&lsmdata, rule->lsm[i].type,
 						   Audit_equal,
-						   rule->lsm[i].rule);
+						   rule->lsm[i].rules);
 			break;
 		case LSM_SUBJ_USER:
 		case LSM_SUBJ_ROLE:
 		case LSM_SUBJ_TYPE:
-			rc = ima_filter_rule_match(secid, rule->lsm[i].type,
+			rc = ima_filter_rule_match(&lsmdata, rule->lsm[i].type,
 						   Audit_equal,
-						   rule->lsm[i].rule);
+						   rule->lsm[i].rules);
 			break;
 		default:
 			break;
@@ -652,9 +672,10 @@
  * @inode: pointer to an inode for which the policy decision is being made
  * @cred: pointer to a credentials structure for which the policy decision is
  *        being made
- * @secid: LSM secid of the task to be validated
+ * @blob: LSM data of the task to be validated
  * @func: IMA hook identifier
  * @mask: requested action (MAY_READ | MAY_WRITE | MAY_APPEND | MAY_EXEC)
+ * @flags: IMA actions to consider (e.g. IMA_MEASURE | IMA_APPRAISE)
  * @pcr: set the pcr to extend
  * @template_desc: the template that should be used for this rule
  * @func_data: func specific data, may be NULL
@@ -668,24 +689,26 @@
  * than writes so ima_match_policy() is classical RCU candidate.
  */
 int ima_match_policy(struct user_namespace *mnt_userns, struct inode *inode,
-		     const struct cred *cred, u32 secid, enum ima_hooks func,
-		     int mask, int flags, int *pcr,
+		     const struct cred *cred, struct lsmblob *blob,
+		     enum ima_hooks func, int mask, int flags, int *pcr,
 		     struct ima_template_desc **template_desc,
 		     const char *func_data, unsigned int *allowed_algos)
 {
 	struct ima_rule_entry *entry;
 	int action = 0, actmask = flags | (flags << 1);
+	struct list_head *ima_rules_tmp;
 
 	if (template_desc && !*template_desc)
 		*template_desc = ima_template_desc_current();
 
 	rcu_read_lock();
-	list_for_each_entry_rcu(entry, ima_rules, list) {
+	ima_rules_tmp = rcu_dereference(ima_rules);
+	list_for_each_entry_rcu(entry, ima_rules_tmp, list) {
 
 		if (!(entry->action & actmask))
 			continue;
 
-		if (!ima_match_rules(entry, mnt_userns, inode, cred, secid,
+		if (!ima_match_rules(entry, mnt_userns, inode, cred, blob,
 				     func, mask, func_data))
 			continue;
 
@@ -741,9 +764,11 @@
 {
 	struct ima_rule_entry *entry;
 	int new_policy_flag = 0;
+	struct list_head *ima_rules_tmp;
 
 	rcu_read_lock();
-	list_for_each_entry(entry, ima_rules, list) {
+	ima_rules_tmp = rcu_dereference(ima_rules);
+	list_for_each_entry_rcu(entry, ima_rules_tmp, list) {
 		/*
 		 * SETXATTR_CHECK rules do not implement a full policy check
 		 * because rule checking would probably have an important
@@ -968,10 +993,10 @@
 
 	list_splice_tail_init_rcu(&ima_temp_rules, policy, synchronize_rcu);
 
-	if (ima_rules != policy) {
+	if (ima_rules != (struct list_head __rcu *)policy) {
 		ima_policy_flag = 0;
-		ima_rules = policy;
 
+		rcu_assign_pointer(ima_rules, policy);
 		/*
 		 * IMA architecture specific policy rules are specified
 		 * as strings and converted to an array of ima_entry_rules
@@ -1046,7 +1071,7 @@
 {
 	int result;
 
-	if (entry->lsm[lsm_rule].rule)
+	if (ima_lsm_isset(entry->lsm[lsm_rule].rules))
 		return -EINVAL;
 
 	entry->lsm[lsm_rule].args_p = match_strdup(args);
@@ -1056,12 +1081,13 @@
 	entry->lsm[lsm_rule].type = audit_type;
 	result = ima_filter_rule_init(entry->lsm[lsm_rule].type, Audit_equal,
 				      entry->lsm[lsm_rule].args_p,
-				      &entry->lsm[lsm_rule].rule);
-	if (!entry->lsm[lsm_rule].rule) {
+				      &entry->lsm[lsm_rule].rules[0],
+				      GFP_KERNEL);
+	if (!ima_lsm_isset(entry->lsm[lsm_rule].rules)) {
 		pr_warn("rule for LSM \'%s\' is undefined\n",
 			entry->lsm[lsm_rule].args_p);
 
-		if (ima_rules == &ima_default_rules) {
+		if (ima_rules == (struct list_head __rcu *)(&ima_default_rules)) {
 			kfree(entry->lsm[lsm_rule].args_p);
 			entry->lsm[lsm_rule].args_p = NULL;
 			result = -EINVAL;
@@ -1686,7 +1712,7 @@
 
 /**
  * ima_parse_add_rule - add a rule to ima_policy_rules
- * @rule - ima measurement policy rule
+ * @rule: ima measurement policy rule
  *
  * Avoid locking by allowing just one writer at a time in ima_write_policy()
  * Returns the length of the rule parsed, an error code on failure
@@ -1768,9 +1794,11 @@
 {
 	loff_t l = *pos;
 	struct ima_rule_entry *entry;
+	struct list_head *ima_rules_tmp;
 
 	rcu_read_lock();
-	list_for_each_entry_rcu(entry, ima_rules, list) {
+	ima_rules_tmp = rcu_dereference(ima_rules);
+	list_for_each_entry_rcu(entry, ima_rules_tmp, list) {
 		if (!l--) {
 			rcu_read_unlock();
 			return entry;
@@ -1789,7 +1817,8 @@
 	rcu_read_unlock();
 	(*pos)++;
 
-	return (&entry->list == ima_rules) ? NULL : entry;
+	return (&entry->list == &ima_default_rules ||
+		&entry->list == &ima_policy_rules) ? NULL : entry;
 }
 
 void ima_policy_stop(struct seq_file *m, void *v)
@@ -1845,6 +1874,14 @@
 
 	rcu_read_lock();
 
+	/* Do not print rules with inactive LSM labels */
+	for (i = 0; i < MAX_LSM_RULES; i++) {
+		if (entry->lsm[i].args_p && !ima_lsm_isset(entry->lsm[i].rules)) {
+			rcu_read_unlock();
+			return 0;
+		}
+	}
+
 	if (entry->action & MEASURE)
 		seq_puts(m, pt(Opt_measure));
 	if (entry->action & DONT_MEASURE)
@@ -1954,7 +1991,7 @@
 	}
 
 	for (i = 0; i < MAX_LSM_RULES; i++) {
-		if (entry->lsm[i].rule) {
+		if (ima_lsm_isset(entry->lsm[i].rules)) {
 			switch (i) {
 			case LSM_OBJ_USER:
 				seq_printf(m, pt(Opt_obj_user),
@@ -2014,14 +2051,20 @@
 	struct ima_rule_entry *entry;
 	bool found = false;
 	enum ima_hooks func;
+	struct list_head *ima_rules_tmp;
 
 	if (id >= READING_MAX_ID)
 		return false;
 
+	if (id == READING_KEXEC_IMAGE && !(ima_appraise & IMA_APPRAISE_ENFORCE)
+	    && security_locked_down(LOCKDOWN_KEXEC))
+		return false;
+
 	func = read_idmap[id] ?: FILE_CHECK;
 
 	rcu_read_lock();
-	list_for_each_entry_rcu(entry, ima_rules, list) {
+	ima_rules_tmp = rcu_dereference(ima_rules);
+	list_for_each_entry_rcu(entry, ima_rules_tmp, list) {
 		if (entry->action != APPRAISE)
 			continue;
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_template.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_template.c
@@ -29,6 +29,7 @@
 
 static LIST_HEAD(defined_templates);
 static DEFINE_SPINLOCK(template_list);
+static int template_setup_done;
 
 static const struct ima_template_field supported_fields[] = {
 	{.field_id = "d", .field_init = ima_eventdigest_init,
@@ -101,10 +102,11 @@
 	struct ima_template_desc *template_desc;
 	int template_len = strlen(str);
 
-	if (ima_template)
+	if (template_setup_done)
 		return 1;
 
-	ima_init_template_list();
+	if (!ima_template)
+		ima_init_template_list();
 
 	/*
 	 * Verify that a template with the supplied name exists.
@@ -128,6 +130,7 @@
 	}
 
 	ima_template = template_desc;
+	template_setup_done = 1;
 	return 1;
 }
 __setup("ima_template=", ima_template_setup);
@@ -136,7 +139,7 @@
 {
 	int num_templates = ARRAY_SIZE(builtin_templates);
 
-	if (ima_template)
+	if (template_setup_done)
 		return 1;
 
 	if (template_desc_init_fields(str, NULL, NULL) < 0) {
@@ -147,6 +150,7 @@
 
 	builtin_templates[num_templates - 1].fmt = str;
 	ima_template = builtin_templates + num_templates - 1;
+	template_setup_done = 1;
 
 	return 1;
 }
@@ -237,11 +241,11 @@
 	}
 
 	if (fields && num_fields) {
-		*fields = kmalloc_array(i, sizeof(*fields), GFP_KERNEL);
+		*fields = kmalloc_array(i, sizeof(**fields), GFP_KERNEL);
 		if (*fields == NULL)
 			return -ENOMEM;
 
-		memcpy(*fields, found_fields, i * sizeof(*fields));
+		memcpy(*fields, found_fields, i * sizeof(**fields));
 		*num_fields = i;
 	}
 
@@ -332,8 +336,11 @@
 
 	template_desc->name = "";
 	template_desc->fmt = kstrdup(template_name, GFP_KERNEL);
-	if (!template_desc->fmt)
+	if (!template_desc->fmt) {
+		kfree(template_desc);
+		template_desc = NULL;
 		goto out;
+	}
 
 	spin_lock(&template_list);
 	list_add_tail_rcu(&template_desc->list, &defined_templates);
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/ima/ima_template_lib.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/ima/ima_template_lib.c
@@ -426,7 +426,10 @@
 				     bool size_limit)
 {
 	const char *cur_filename = NULL;
+	struct name_snapshot filename;
 	u32 cur_filename_len = 0;
+	bool snapshot = false;
+	int ret;
 
 	BUG_ON(event_data->filename == NULL && event_data->file == NULL);
 
@@ -439,7 +442,10 @@
 	}
 
 	if (event_data->file) {
-		cur_filename = event_data->file->f_path.dentry->d_name.name;
+		take_dentry_name_snapshot(&filename,
+					  event_data->file->f_path.dentry);
+		snapshot = true;
+		cur_filename = filename.name.name;
 		cur_filename_len = strlen(cur_filename);
 	} else
 		/*
@@ -448,8 +454,13 @@
 		 */
 		cur_filename_len = IMA_EVENT_NAME_LEN_MAX;
 out:
-	return ima_write_template_field_data(cur_filename, cur_filename_len,
-					     DATA_FMT_STRING, field_data);
+	ret = ima_write_template_field_data(cur_filename, cur_filename_len,
+					    DATA_FMT_STRING, field_data);
+
+	if (snapshot)
+		release_dentry_name_snapshot(&filename);
+
+	return ret;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/integrity.h
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/integrity.h
@@ -131,6 +131,8 @@
 	unsigned long flags;
 	unsigned long measured_pcrs;
 	unsigned long atomic_flags;
+	unsigned long real_ino;
+	dev_t real_dev;
 	enum integrity_status ima_file_status:4;
 	enum integrity_status ima_mmap_status:4;
 	enum integrity_status ima_bprm_status:4;
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/integrity_audit.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/integrity_audit.c
@@ -45,12 +45,14 @@
 		return;
 
 	ab = audit_log_start(audit_context(), GFP_KERNEL, audit_msgno);
+	if (!ab)
+		return;
 	audit_log_format(ab, "pid=%d uid=%u auid=%u ses=%u",
 			 task_pid_nr(current),
 			 from_kuid(&init_user_ns, current_uid()),
 			 from_kuid(&init_user_ns, audit_get_loginuid(current)),
 			 audit_get_sessionid(current));
-	audit_log_task_context(ab);
+	audit_log_task_context(ab, NULL);
 	audit_log_format(ab, " op=%s cause=%s comm=", op, cause);
 	audit_log_untrustedstring(ab, get_task_comm(name, current));
 	if (fname) {
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/platform_certs/keyring_handler.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/platform_certs/keyring_handler.c
@@ -61,6 +61,7 @@
 static __init void uefi_revocation_list_x509(const char *source,
 					     const void *data, size_t len)
 {
+	pr_info("Revoking X.509 certificate: %s\n", source);
 	add_key_to_revocation_list(data, len);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/platform_certs/keyring_handler.h
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/platform_certs/keyring_handler.h
@@ -30,3 +30,11 @@
 efi_element_handler_t get_handler_for_dbx(const efi_guid_t *sig_type);
 
 #endif
+
+#ifndef UEFI_QUIRK_SKIP_CERT
+#define UEFI_QUIRK_SKIP_CERT(vendor, product) \
+		 .matches = { \
+			DMI_MATCH(DMI_BOARD_VENDOR, vendor), \
+			DMI_MATCH(DMI_PRODUCT_NAME, product), \
+		},
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/security/integrity/platform_certs/load_uefi.c
+++ linux-xilinx-zynqmp-5.15.0/security/integrity/platform_certs/load_uefi.c
@@ -3,6 +3,7 @@
 #include <linux/kernel.h>
 #include <linux/sched.h>
 #include <linux/cred.h>
+#include <linux/dmi.h>
 #include <linux/err.h>
 #include <linux/efi.h>
 #include <linux/slab.h>
@@ -12,6 +13,32 @@
 #include "keyring_handler.h"
 
 /*
+ * On T2 Macs reading the db and dbx efi variables to load UEFI Secure Boot
+ * certificates causes occurrence of a page fault in Apple's firmware and
+ * a crash disabling EFI runtime services. The following quirk skips reading
+ * these variables.
+ */
+static const struct dmi_system_id uefi_skip_cert[] = {
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro15,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro15,2") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro15,3") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro15,4") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro16,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro16,2") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro16,3") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookPro16,4") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookAir8,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookAir8,2") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacBookAir9,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "Macmini8,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "MacPro7,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "iMac20,1") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "iMac20,2") },
+	{ UEFI_QUIRK_SKIP_CERT("Apple Inc.", "iMacPro1,1") },
+	{ }
+};
+
+/*
  * Look to see if a UEFI variable called MokIgnoreDB exists and return true if
  * it does.
  *
@@ -46,7 +73,8 @@
 		return NULL;
 
 	if (*status != EFI_BUFFER_TOO_SMALL) {
-		pr_err("Couldn't get size: 0x%lx\n", *status);
+		pr_err("Couldn't get size: %s (0x%lx)\n",
+		       efi_status_to_str(*status), *status);
 		return NULL;
 	}
 
@@ -57,7 +85,8 @@
 	*status = efi.get_variable(name, guid, NULL, &lsize, db);
 	if (*status != EFI_SUCCESS) {
 		kfree(db);
-		pr_err("Error reading db var: 0x%lx\n", *status);
+		pr_err("Error reading db var: %s (0x%lx)\n",
+		       efi_status_to_str(*status), *status);
 		return NULL;
 	}
 
@@ -66,17 +95,18 @@
 }
 
 /*
- * load_moklist_certs() - Load MokList certs
+ * load_moklist_certs() - Load Mok(X)List certs
+ * @load_db: Load MokListRT into db when true; MokListXRT into dbx when false
  *
- * Load the certs contained in the UEFI MokListRT database into the
- * platform trusted keyring.
+ * Load the certs contained in the UEFI MokList(X)RT database into the
+ * platform trusted/denied keyring.
  *
  * This routine checks the EFI MOK config table first. If and only if
- * that fails, this routine uses the MokListRT ordinary UEFI variable.
+ * that fails, this routine uses the MokList(X)RT ordinary UEFI variable.
  *
  * Return:	Status
  */
-static int __init load_moklist_certs(void)
+static int __init load_moklist_certs(const bool load_db)
 {
 	struct efi_mokvar_table_entry *mokvar_entry;
 	efi_guid_t mok_var = EFI_SHIM_LOCK_GUID;
@@ -84,41 +114,55 @@
 	unsigned long moksize;
 	efi_status_t status;
 	int rc;
+	const char *mokvar_name = "MokListRT";
+	/* Should be const, but get_cert_list() doesn't have it as const yet */
+	efi_char16_t *efivar_name = L"MokListRT";
+	const char *parse_mokvar_name = "UEFI:MokListRT (MOKvar table)";
+	const char *parse_efivar_name = "UEFI:MokListRT";
+	efi_element_handler_t (*get_handler_for_guid)(const efi_guid_t *) = get_handler_for_db;
+
+	if (!load_db) {
+		mokvar_name = "MokListXRT";
+		efivar_name = L"MokListXRT";
+		parse_mokvar_name = "UEFI:MokListXRT (MOKvar table)";
+		parse_efivar_name = "UEFI:MokListXRT";
+		get_handler_for_guid = get_handler_for_dbx;
+	}
 
 	/* First try to load certs from the EFI MOKvar config table.
 	 * It's not an error if the MOKvar config table doesn't exist
 	 * or the MokListRT entry is not found in it.
 	 */
-	mokvar_entry = efi_mokvar_entry_find("MokListRT");
+	mokvar_entry = efi_mokvar_entry_find(mokvar_name);
 	if (mokvar_entry) {
-		rc = parse_efi_signature_list("UEFI:MokListRT (MOKvar table)",
+		rc = parse_efi_signature_list(parse_mokvar_name,
 					      mokvar_entry->data,
 					      mokvar_entry->data_size,
-					      get_handler_for_db);
+					      get_handler_for_guid);
 		/* All done if that worked. */
 		if (!rc)
 			return rc;
 
-		pr_err("Couldn't parse MokListRT signatures from EFI MOKvar config table: %d\n",
-		       rc);
+		pr_err("Couldn't parse %s signatures from EFI MOKvar config table: %d\n",
+		       mokvar_name, rc);
 	}
 
 	/* Get MokListRT. It might not exist, so it isn't an error
 	 * if we can't get it.
 	 */
-	mok = get_cert_list(L"MokListRT", &mok_var, &moksize, &status);
+	mok = get_cert_list(efivar_name, &mok_var, &moksize, &status);
 	if (mok) {
-		rc = parse_efi_signature_list("UEFI:MokListRT",
-					      mok, moksize, get_handler_for_db);
+		rc = parse_efi_signature_list(parse_efivar_name,
+					      mok, moksize, get_handler_for_guid);
 		kfree(mok);
 		if (rc)
-			pr_err("Couldn't parse MokListRT signatures: %d\n", rc);
+			pr_err("Couldn't parse %s signatures: %d\n", mokvar_name, rc);
 		return rc;
 	}
 	if (status == EFI_NOT_FOUND)
-		pr_debug("MokListRT variable wasn't found\n");
+		pr_debug("%s variable wasn't found\n", mokvar_name);
 	else
-		pr_info("Couldn't get UEFI MokListRT\n");
+		pr_info("Couldn't get UEFI %s\n", mokvar_name);
 	return 0;
 }
 
@@ -132,11 +176,17 @@
 static int __init load_uefi_certs(void)
 {
 	efi_guid_t secure_var = EFI_IMAGE_SECURITY_DATABASE_GUID;
-	efi_guid_t mok_var = EFI_SHIM_LOCK_GUID;
-	void *db = NULL, *dbx = NULL, *mokx = NULL;
-	unsigned long dbsize = 0, dbxsize = 0, mokxsize = 0;
+	void *db = NULL, *dbx = NULL;
+	unsigned long dbsize = 0, dbxsize = 0;
 	efi_status_t status;
 	int rc = 0;
+	const struct dmi_system_id *dmi_id;
+
+	dmi_id = dmi_first_match(uefi_skip_cert);
+	if (dmi_id) {
+		pr_err("Reading UEFI Secure Boot Certs is not supported on T2 Macs.\n");
+		return false;
+	}
 
 	if (!efi_rt_services_supported(EFI_RT_SUPPORTED_GET_VARIABLE))
 		return false;
@@ -176,23 +226,15 @@
 		kfree(dbx);
 	}
 
-	mokx = get_cert_list(L"MokListXRT", &mok_var, &mokxsize, &status);
-	if (!mokx) {
-		if (status == EFI_NOT_FOUND)
-			pr_debug("mokx variable wasn't found\n");
-		else
-			pr_info("Couldn't get mokx list\n");
-	} else {
-		rc = parse_efi_signature_list("UEFI:MokListXRT",
-					      mokx, mokxsize,
-					      get_handler_for_dbx);
-		if (rc)
-			pr_err("Couldn't parse mokx signatures %d\n", rc);
-		kfree(mokx);
-	}
+	/* Load the MokListXRT certs */
+	rc = load_moklist_certs(false);
+	if (rc)
+		pr_err("Couldn't parse mokx signatures: %d\n", rc);
 
 	/* Load the MokListRT certs */
-	rc = load_moklist_certs();
+	rc = load_moklist_certs(true);
+	if (rc)
+		pr_err("Couldn't parse mok signatures: %d\n", rc);
 
 	return rc;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/gc.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/gc.c
@@ -67,6 +67,19 @@
 }
 
 /*
+ * Set the expiration time on a key.
+ */
+void key_set_expiry(struct key *key, time64_t expiry)
+{
+	key->expiry = expiry;
+	if (expiry != TIME64_MAX) {
+		if (!(key->type->flags & KEY_TYPE_INSTANT_REAP))
+			expiry += key_gc_delay;
+		key_schedule_gc(expiry);
+	}
+}
+
+/*
  * Schedule a dead links collection run.
  */
 void key_schedule_gc_links(void)
@@ -176,7 +189,6 @@
 	static u8 gc_state;		/* Internal persistent state */
 #define KEY_GC_REAP_AGAIN	0x01	/* - Need another cycle */
 #define KEY_GC_REAPING_LINKS	0x02	/* - We need to reap links */
-#define KEY_GC_SET_TIMER	0x04	/* - We need to restart the timer */
 #define KEY_GC_REAPING_DEAD_1	0x10	/* - We need to mark dead keys */
 #define KEY_GC_REAPING_DEAD_2	0x20	/* - We need to reap dead key links */
 #define KEY_GC_REAPING_DEAD_3	0x40	/* - We need to reap dead keys */
@@ -184,21 +196,17 @@
 
 	struct rb_node *cursor;
 	struct key *key;
-	time64_t new_timer, limit;
+	time64_t new_timer, limit, expiry;
 
 	kenter("[%lx,%x]", key_gc_flags, gc_state);
 
 	limit = ktime_get_real_seconds();
-	if (limit > key_gc_delay)
-		limit -= key_gc_delay;
-	else
-		limit = key_gc_delay;
 
 	/* Work out what we're going to be doing in this pass */
 	gc_state &= KEY_GC_REAPING_DEAD_1 | KEY_GC_REAPING_DEAD_2;
 	gc_state <<= 1;
 	if (test_and_clear_bit(KEY_GC_KEY_EXPIRED, &key_gc_flags))
-		gc_state |= KEY_GC_REAPING_LINKS | KEY_GC_SET_TIMER;
+		gc_state |= KEY_GC_REAPING_LINKS;
 
 	if (test_and_clear_bit(KEY_GC_REAP_KEYTYPE, &key_gc_flags))
 		gc_state |= KEY_GC_REAPING_DEAD_1;
@@ -233,8 +241,11 @@
 			}
 		}
 
-		if (gc_state & KEY_GC_SET_TIMER) {
-			if (key->expiry > limit && key->expiry < new_timer) {
+		expiry = key->expiry;
+		if (expiry != TIME64_MAX) {
+			if (!(key->type->flags & KEY_TYPE_INSTANT_REAP))
+				expiry += key_gc_delay;
+			if (expiry > limit && expiry < new_timer) {
 				kdebug("will expire %x in %lld",
 				       key_serial(key), key->expiry - limit);
 				new_timer = key->expiry;
@@ -276,7 +287,7 @@
 	 */
 	kdebug("pass complete");
 
-	if (gc_state & KEY_GC_SET_TIMER && new_timer != (time64_t)TIME64_MAX) {
+	if (new_timer != TIME64_MAX) {
 		new_timer += key_gc_delay;
 		key_schedule_gc(new_timer);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/internal.h
+++ linux-xilinx-zynqmp-5.15.0/security/keys/internal.h
@@ -176,6 +176,7 @@
 extern void keyring_gc(struct key *keyring, time64_t limit);
 extern void keyring_restriction_gc(struct key *keyring,
 				   struct key_type *dead_type);
+void key_set_expiry(struct key *key, time64_t expiry);
 extern void key_schedule_gc(time64_t gc_at);
 extern void key_schedule_gc_links(void);
 extern void key_gc_keytype(struct key_type *ktype);
@@ -224,10 +225,18 @@
  */
 static inline bool key_is_dead(const struct key *key, time64_t limit)
 {
+	time64_t expiry = key->expiry;
+
+	if (expiry != TIME64_MAX) {
+		if (!(key->type->flags & KEY_TYPE_INSTANT_REAP))
+			expiry += key_gc_delay;
+		if (expiry <= limit)
+			return true;
+	}
+
 	return
 		key->flags & ((1 << KEY_FLAG_DEAD) |
 			      (1 << KEY_FLAG_INVALIDATED)) ||
-		(key->expiry > 0 && key->expiry <= limit) ||
 		key->domain_tag->removed;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/key.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/key.c
@@ -294,6 +294,7 @@
 	key->uid = uid;
 	key->gid = gid;
 	key->perm = perm;
+	key->expiry = TIME64_MAX;
 	key->restrict_link = restrict_link;
 	key->last_used_at = ktime_get_real_seconds();
 
@@ -463,10 +464,8 @@
 			if (authkey)
 				key_invalidate(authkey);
 
-			if (prep->expiry != TIME64_MAX) {
-				key->expiry = prep->expiry;
-				key_schedule_gc(prep->expiry + key_gc_delay);
-			}
+			if (prep->expiry != TIME64_MAX)
+				key_set_expiry(key, prep->expiry);
 		}
 	}
 
@@ -606,8 +605,7 @@
 		atomic_inc(&key->user->nikeys);
 		mark_key_instantiated(key, -error);
 		notify_key(key, NOTIFY_KEY_INSTANTIATED, -error);
-		key->expiry = ktime_get_real_seconds() + timeout;
-		key_schedule_gc(key->expiry + key_gc_delay);
+		key_set_expiry(key, ktime_get_real_seconds() + timeout);
 
 		if (test_and_clear_bit(KEY_FLAG_USER_CONSTRUCT, &key->flags))
 			awaken = 1;
@@ -722,16 +720,14 @@
 
 void key_set_timeout(struct key *key, unsigned timeout)
 {
-	time64_t expiry = 0;
+	time64_t expiry = TIME64_MAX;
 
 	/* make the changes with the locks held to prevent races */
 	down_write(&key->sem);
 
 	if (timeout > 0)
 		expiry = ktime_get_real_seconds() + timeout;
-
-	key->expiry = expiry;
-	key_schedule_gc(key->expiry + key_gc_delay);
+	key_set_expiry(key, expiry);
 
 	up_write(&key->sem);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/keyctl.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/keyctl.c
@@ -980,14 +980,19 @@
 	ret = -EACCES;
 	down_write(&key->sem);
 
-	if (!capable(CAP_SYS_ADMIN)) {
+	{
+		bool is_privileged_op = false;
+
 		/* only the sysadmin can chown a key to some other UID */
 		if (user != (uid_t) -1 && !uid_eq(key->uid, uid))
-			goto error_put;
+			is_privileged_op = true;
 
 		/* only the sysadmin can set the key's GID to a group other
 		 * than one of those that the current process subscribes to */
 		if (group != (gid_t) -1 && !gid_eq(gid, key->gid) && !in_group_p(gid))
+			is_privileged_op = true;
+
+		if (is_privileged_op && !capable(CAP_SYS_ADMIN))
 			goto error_put;
 	}
 
@@ -1088,7 +1093,7 @@
 	down_write(&key->sem);
 
 	/* if we're not the sysadmin, we can only change a key that we own */
-	if (capable(CAP_SYS_ADMIN) || uid_eq(key->uid, current_fsuid())) {
+	if (uid_eq(key->uid, current_fsuid()) || capable(CAP_SYS_ADMIN)) {
 		key->perm = perm;
 		notify_key(key, NOTIFY_KEY_SETATTR, 0);
 		ret = 0;
@@ -1689,7 +1694,7 @@
 		goto unlock;
 
 	/* cancel an already pending keyring replacement */
-	oldwork = task_work_cancel(parent, key_change_session_keyring);
+	oldwork = task_work_cancel_func(parent, key_change_session_keyring);
 
 	/* the replacement session keyring is applied just prior to userspace
 	 * restarting */
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/keyctl_pkey.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/keyctl_pkey.c
@@ -135,15 +135,23 @@
 
 	switch (op) {
 	case KEYCTL_PKEY_ENCRYPT:
+		if (uparams.in_len  > info.max_dec_size ||
+		    uparams.out_len > info.max_enc_size)
+			return -EINVAL;
+		break;
 	case KEYCTL_PKEY_DECRYPT:
 		if (uparams.in_len  > info.max_enc_size ||
 		    uparams.out_len > info.max_dec_size)
 			return -EINVAL;
 		break;
 	case KEYCTL_PKEY_SIGN:
+		if (uparams.in_len  > info.max_data_size ||
+		    uparams.out_len > info.max_sig_size)
+			return -EINVAL;
+		break;
 	case KEYCTL_PKEY_VERIFY:
-		if (uparams.in_len  > info.max_sig_size ||
-		    uparams.out_len > info.max_data_size)
+		if (uparams.in_len  > info.max_data_size ||
+		    uparams.in2_len > info.max_sig_size)
 			return -EINVAL;
 		break;
 	default:
@@ -151,7 +159,7 @@
 	}
 
 	params->in_len  = uparams.in_len;
-	params->out_len = uparams.out_len;
+	params->out_len = uparams.out_len; /* Note: same as in2_len */
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/keyring.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/keyring.c
@@ -772,8 +772,11 @@
 	for (; slot < ASSOC_ARRAY_FAN_OUT; slot++) {
 		ptr = READ_ONCE(node->slots[slot]);
 
-		if (assoc_array_ptr_is_meta(ptr) && node->back_pointer)
-			goto descend_to_node;
+		if (assoc_array_ptr_is_meta(ptr)) {
+			if (node->back_pointer ||
+			    assoc_array_ptr_is_shortcut(ptr))
+				goto descend_to_node;
+		}
 
 		if (!keyring_ptr_is_keyring(ptr))
 			continue;
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/proc.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/proc.c
@@ -198,7 +198,7 @@
 
 	/* come up with a suitable timeout value */
 	expiry = READ_ONCE(key->expiry);
-	if (expiry == 0) {
+	if (expiry == TIME64_MAX) {
 		memcpy(xbuf, "perm", 5);
 	} else if (now >= expiry) {
 		memcpy(xbuf, "expd", 5);
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/request_key.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/request_key.c
@@ -38,9 +38,12 @@
 #ifdef CONFIG_KEYS_REQUEST_CACHE
 	struct task_struct *t = current;
 
-	key_put(t->cached_requested_key);
-	t->cached_requested_key = key_get(key);
-	set_tsk_thread_flag(t, TIF_NOTIFY_RESUME);
+	/* Do not cache key if it is a kernel thread */
+	if (!(t->flags & PF_KTHREAD)) {
+		key_put(t->cached_requested_key);
+		t->cached_requested_key = key_get(key);
+		set_tsk_thread_flag(t, TIF_NOTIFY_RESUME);
+	}
 #endif
 }
 
@@ -398,17 +401,21 @@
 	set_bit(KEY_FLAG_USER_CONSTRUCT, &key->flags);
 
 	if (dest_keyring) {
-		ret = __key_link_lock(dest_keyring, &ctx->index_key);
+		ret = __key_link_lock(dest_keyring, &key->index_key);
 		if (ret < 0)
 			goto link_lock_failed;
-		ret = __key_link_begin(dest_keyring, &ctx->index_key, &edit);
-		if (ret < 0)
-			goto link_prealloc_failed;
 	}
 
-	/* attach the key to the destination keyring under lock, but we do need
+	/*
+	 * Attach the key to the destination keyring under lock, but we do need
 	 * to do another check just in case someone beat us to it whilst we
-	 * waited for locks */
+	 * waited for locks.
+	 *
+	 * The caller might specify a comparison function which looks for keys
+	 * that do not exactly match but are still equivalent from the caller's
+	 * perspective. The __key_link_begin() operation must be done only after
+	 * an actual key is determined.
+	 */
 	mutex_lock(&key_construction_mutex);
 
 	rcu_read_lock();
@@ -417,12 +424,16 @@
 	if (!IS_ERR(key_ref))
 		goto key_already_present;
 
-	if (dest_keyring)
+	if (dest_keyring) {
+		ret = __key_link_begin(dest_keyring, &key->index_key, &edit);
+		if (ret < 0)
+			goto link_alloc_failed;
 		__key_link(dest_keyring, key, &edit);
+	}
 
 	mutex_unlock(&key_construction_mutex);
 	if (dest_keyring)
-		__key_link_end(dest_keyring, &ctx->index_key, edit);
+		__key_link_end(dest_keyring, &key->index_key, edit);
 	mutex_unlock(&user->cons_lock);
 	*_key = key;
 	kleave(" = 0 [%d]", key_serial(key));
@@ -435,10 +446,13 @@
 	mutex_unlock(&key_construction_mutex);
 	key = key_ref_to_ptr(key_ref);
 	if (dest_keyring) {
+		ret = __key_link_begin(dest_keyring, &key->index_key, &edit);
+		if (ret < 0)
+			goto link_alloc_failed_unlocked;
 		ret = __key_link_check_live_key(dest_keyring, key);
 		if (ret == 0)
 			__key_link(dest_keyring, key, &edit);
-		__key_link_end(dest_keyring, &ctx->index_key, edit);
+		__key_link_end(dest_keyring, &key->index_key, edit);
 		if (ret < 0)
 			goto link_check_failed;
 	}
@@ -453,8 +467,10 @@
 	kleave(" = %d [linkcheck]", ret);
 	return ret;
 
-link_prealloc_failed:
-	__key_link_end(dest_keyring, &ctx->index_key, edit);
+link_alloc_failed:
+	mutex_unlock(&key_construction_mutex);
+link_alloc_failed_unlocked:
+	__key_link_end(dest_keyring, &key->index_key, edit);
 link_lock_failed:
 	mutex_unlock(&user->cons_lock);
 	key_put(key);
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/trusted-keys/trusted_core.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/trusted-keys/trusted_core.c
@@ -16,32 +16,36 @@
 #include <linux/key-type.h>
 #include <linux/module.h>
 #include <linux/parser.h>
+#include <linux/random.h>
 #include <linux/rcupdate.h>
 #include <linux/slab.h>
 #include <linux/static_call.h>
 #include <linux/string.h>
 #include <linux/uaccess.h>
 
+static char *trusted_rng = "default";
+module_param_named(rng, trusted_rng, charp, 0);
+MODULE_PARM_DESC(rng, "Select trusted key RNG");
+
 static char *trusted_key_source;
 module_param_named(source, trusted_key_source, charp, 0);
 MODULE_PARM_DESC(source, "Select trusted keys source (tpm or tee)");
 
 static const struct trusted_key_source trusted_key_sources[] = {
-#if defined(CONFIG_TCG_TPM)
+#if IS_REACHABLE(CONFIG_TCG_TPM)
 	{ "tpm", &trusted_key_tpm_ops },
 #endif
-#if defined(CONFIG_TEE)
+#if IS_REACHABLE(CONFIG_TEE)
 	{ "tee", &trusted_key_tee_ops },
 #endif
 };
 
-DEFINE_STATIC_CALL_NULL(trusted_key_init, *trusted_key_sources[0].ops->init);
 DEFINE_STATIC_CALL_NULL(trusted_key_seal, *trusted_key_sources[0].ops->seal);
 DEFINE_STATIC_CALL_NULL(trusted_key_unseal,
 			*trusted_key_sources[0].ops->unseal);
 DEFINE_STATIC_CALL_NULL(trusted_key_get_random,
 			*trusted_key_sources[0].ops->get_random);
-DEFINE_STATIC_CALL_NULL(trusted_key_exit, *trusted_key_sources[0].ops->exit);
+static void (*trusted_key_exit)(void);
 static unsigned char migratable;
 
 enum {
@@ -312,8 +316,14 @@
 };
 EXPORT_SYMBOL_GPL(key_type_trusted);
 
+static int kernel_get_random(unsigned char *key, size_t key_len)
+{
+	return get_random_bytes_wait(key, key_len) ?: key_len;
+}
+
 static int __init init_trusted(void)
 {
+	int (*get_random)(unsigned char *key, size_t key_len);
 	int i, ret = 0;
 
 	for (i = 0; i < ARRAY_SIZE(trusted_key_sources); i++) {
@@ -322,20 +332,39 @@
 			    strlen(trusted_key_sources[i].name)))
 			continue;
 
-		static_call_update(trusted_key_init,
-				   trusted_key_sources[i].ops->init);
-		static_call_update(trusted_key_seal,
-				   trusted_key_sources[i].ops->seal);
-		static_call_update(trusted_key_unseal,
-				   trusted_key_sources[i].ops->unseal);
-		static_call_update(trusted_key_get_random,
-				   trusted_key_sources[i].ops->get_random);
-		static_call_update(trusted_key_exit,
-				   trusted_key_sources[i].ops->exit);
-		migratable = trusted_key_sources[i].ops->migratable;
+		/*
+		 * We always support trusted.rng="kernel" and "default" as
+		 * well as trusted.rng=$trusted.source if the trust source
+		 * defines its own get_random callback.
+		 */
+		get_random = trusted_key_sources[i].ops->get_random;
+		if (trusted_rng && strcmp(trusted_rng, "default")) {
+			if (!strcmp(trusted_rng, "kernel")) {
+				get_random = kernel_get_random;
+			} else if (strcmp(trusted_rng, trusted_key_sources[i].name) ||
+				   !get_random) {
+				pr_warn("Unsupported RNG. Supported: kernel");
+				if (get_random)
+					pr_cont(", %s", trusted_key_sources[i].name);
+				pr_cont(", default\n");
+				return -EINVAL;
+			}
+		}
+
+		if (!get_random)
+			get_random = kernel_get_random;
+
+		ret = trusted_key_sources[i].ops->init();
+		if (!ret) {
+			static_call_update(trusted_key_seal, trusted_key_sources[i].ops->seal);
+			static_call_update(trusted_key_unseal, trusted_key_sources[i].ops->unseal);
+			static_call_update(trusted_key_get_random, get_random);
+
+			trusted_key_exit = trusted_key_sources[i].ops->exit;
+			migratable = trusted_key_sources[i].ops->migratable;
+		}
 
-		ret = static_call(trusted_key_init)();
-		if (!ret)
+		if (!ret || ret != -ENODEV)
 			break;
 	}
 
@@ -351,7 +380,8 @@
 
 static void __exit cleanup_trusted(void)
 {
-	static_call(trusted_key_exit)();
+	if (trusted_key_exit)
+		(*trusted_key_exit)();
 }
 
 late_initcall(init_trusted);
--- linux-xilinx-zynqmp-5.15.0.orig/security/keys/trusted-keys/trusted_tpm2.c
+++ linux-xilinx-zynqmp-5.15.0/security/keys/trusted-keys/trusted_tpm2.c
@@ -38,6 +38,7 @@
 	u8 *end_work = scratch + SCRATCH_SIZE;
 	u8 *priv, *pub;
 	u16 priv_len, pub_len;
+	int ret;
 
 	priv_len = get_unaligned_be16(src) + 2;
 	priv = src;
@@ -57,8 +58,10 @@
 		unsigned char bool[3], *w = bool;
 		/* tag 0 is emptyAuth */
 		w = asn1_encode_boolean(w, w + sizeof(bool), true);
-		if (WARN(IS_ERR(w), "BUG: Boolean failed to encode"))
-			return PTR_ERR(w);
+		if (WARN(IS_ERR(w), "BUG: Boolean failed to encode")) {
+			ret = PTR_ERR(w);
+			goto err;
+		}
 		work = asn1_encode_tag(work, end_work, 0, bool, w - bool);
 	}
 
@@ -69,8 +72,10 @@
 	 * trigger, so if it does there's something nefarious going on
 	 */
 	if (WARN(work - scratch + pub_len + priv_len + 14 > SCRATCH_SIZE,
-		 "BUG: scratch buffer is too small"))
-		return -EINVAL;
+		 "BUG: scratch buffer is too small")) {
+		ret = -EINVAL;
+		goto err;
+	}
 
 	work = asn1_encode_integer(work, end_work, options->keyhandle);
 	work = asn1_encode_octet_string(work, end_work, pub, pub_len);
@@ -79,10 +84,18 @@
 	work1 = payload->blob;
 	work1 = asn1_encode_sequence(work1, work1 + sizeof(payload->blob),
 				     scratch, work - scratch);
-	if (WARN(IS_ERR(work1), "BUG: ASN.1 encoder failed"))
-		return PTR_ERR(work1);
+	if (IS_ERR(work1)) {
+		ret = PTR_ERR(work1);
+		pr_err("BUG: ASN.1 encoder failed with %d\n", ret);
+		goto err;
+	}
 
+	kfree(scratch);
 	return work1 - payload->blob;
+
+err:
+	kfree(scratch);
+	return ret;
 }
 
 struct tpm2_key_context {
@@ -186,7 +199,7 @@
 }
 
 /**
- * tpm_buf_append_auth() - append TPMS_AUTH_COMMAND to the buffer.
+ * tpm2_buf_append_auth() - append TPMS_AUTH_COMMAND to the buffer.
  *
  * @buf: an allocated tpm_buf instance
  * @session_handle: session handle
@@ -283,8 +296,8 @@
 	/* key properties */
 	flags = 0;
 	flags |= options->policydigest_len ? 0 : TPM2_OA_USER_WITH_AUTH;
-	flags |= payload->migratable ? (TPM2_OA_FIXED_TPM |
-					TPM2_OA_FIXED_PARENT) : 0;
+	flags |= payload->migratable ? 0 : (TPM2_OA_FIXED_TPM |
+					    TPM2_OA_FIXED_PARENT);
 	tpm_buf_append_u32(&buf, flags);
 
 	/* policy */
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/cred.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/cred.c
@@ -14,8 +14,8 @@
 #include "ruleset.h"
 #include "setup.h"
 
-static int hook_cred_prepare(struct cred *const new,
-		const struct cred *const old, const gfp_t gfp)
+static void hook_cred_transfer(struct cred *const new,
+			       const struct cred *const old)
 {
 	struct landlock_ruleset *const old_dom = landlock_cred(old)->domain;
 
@@ -23,6 +23,12 @@
 		landlock_get_ruleset(old_dom);
 		landlock_cred(new)->domain = old_dom;
 	}
+}
+
+static int hook_cred_prepare(struct cred *const new,
+			     const struct cred *const old, const gfp_t gfp)
+{
+	hook_cred_transfer(new, old);
 	return 0;
 }
 
@@ -36,11 +42,12 @@
 
 static struct security_hook_list landlock_hooks[] __lsm_ro_after_init = {
 	LSM_HOOK_INIT(cred_prepare, hook_cred_prepare),
+	LSM_HOOK_INIT(cred_transfer, hook_cred_transfer),
 	LSM_HOOK_INIT(cred_free, hook_cred_free),
 };
 
 __init void landlock_add_cred_hooks(void)
 {
 	security_add_hooks(landlock_hooks, ARRAY_SIZE(landlock_hooks),
-			LANDLOCK_NAME);
+			   &landlock_lsmid);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/cred.h
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/cred.h
@@ -20,8 +20,8 @@
 	struct landlock_ruleset *domain;
 };
 
-static inline struct landlock_cred_security *landlock_cred(
-		const struct cred *cred)
+static inline struct landlock_cred_security *
+landlock_cred(const struct cred *cred)
 {
 	return cred->security + landlock_blob_sizes.lbs_cred;
 }
@@ -34,8 +34,8 @@
 /*
  * The call needs to come from an RCU read-side critical section.
  */
-static inline const struct landlock_ruleset *landlock_get_task_domain(
-		const struct task_struct *const task)
+static inline const struct landlock_ruleset *
+landlock_get_task_domain(const struct task_struct *const task)
 {
 	return landlock_cred(__task_cred(task))->domain;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/fs.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/fs.c
@@ -141,23 +141,26 @@
 }
 
 /* All access rights that can be tied to files. */
+/* clang-format off */
 #define ACCESS_FILE ( \
 	LANDLOCK_ACCESS_FS_EXECUTE | \
 	LANDLOCK_ACCESS_FS_WRITE_FILE | \
 	LANDLOCK_ACCESS_FS_READ_FILE)
+/* clang-format on */
 
 /*
  * @path: Should have been checked by get_path_from_fd().
  */
 int landlock_append_fs_rule(struct landlock_ruleset *const ruleset,
-		const struct path *const path, u32 access_rights)
+			    const struct path *const path,
+			    access_mask_t access_rights)
 {
 	int err;
 	struct landlock_object *object;
 
 	/* Files only get access rights that make sense. */
-	if (!d_is_dir(path->dentry) && (access_rights | ACCESS_FILE) !=
-			ACCESS_FILE)
+	if (!d_is_dir(path->dentry) &&
+	    (access_rights | ACCESS_FILE) != ACCESS_FILE)
 		return -EINVAL;
 	if (WARN_ON_ONCE(ruleset->num_layers != 1))
 		return -EINVAL;
@@ -180,83 +183,129 @@
 
 /* Access-control management */
 
-static inline u64 unmask_layers(
-		const struct landlock_ruleset *const domain,
-		const struct path *const path, const u32 access_request,
-		u64 layer_mask)
+/*
+ * The lifetime of the returned rule is tied to @domain.
+ *
+ * Returns NULL if no rule is found or if @dentry is negative.
+ */
+static inline const struct landlock_rule *
+find_rule(const struct landlock_ruleset *const domain,
+	  const struct dentry *const dentry)
 {
 	const struct landlock_rule *rule;
 	const struct inode *inode;
-	size_t i;
 
-	if (d_is_negative(path->dentry))
-		/* Ignore nonexistent leafs. */
-		return layer_mask;
-	inode = d_backing_inode(path->dentry);
+	/* Ignores nonexistent leafs. */
+	if (d_is_negative(dentry))
+		return NULL;
+
+	inode = d_backing_inode(dentry);
 	rcu_read_lock();
-	rule = landlock_find_rule(domain,
-			rcu_dereference(landlock_inode(inode)->object));
+	rule = landlock_find_rule(
+		domain, rcu_dereference(landlock_inode(inode)->object));
 	rcu_read_unlock();
+	return rule;
+}
+
+/*
+ * @layer_masks is read and may be updated according to the access request and
+ * the matching rule.
+ *
+ * Returns true if the request is allowed (i.e. relevant layer masks for the
+ * request are empty).
+ */
+static inline bool
+unmask_layers(const struct landlock_rule *const rule,
+	      const access_mask_t access_request,
+	      layer_mask_t (*const layer_masks)[LANDLOCK_NUM_ACCESS_FS])
+{
+	size_t layer_level;
+
+	if (!access_request || !layer_masks)
+		return true;
 	if (!rule)
-		return layer_mask;
+		return false;
 
 	/*
 	 * An access is granted if, for each policy layer, at least one rule
-	 * encountered on the pathwalk grants the requested accesses,
-	 * regardless of their position in the layer stack.  We must then check
+	 * encountered on the pathwalk grants the requested access,
+	 * regardless of its position in the layer stack.  We must then check
 	 * the remaining layers for each inode, from the first added layer to
-	 * the last one.
+	 * the last one.  When there is multiple requested accesses, for each
+	 * policy layer, the full set of requested accesses may not be granted
+	 * by only one rule, but by the union (binary OR) of multiple rules.
+	 * E.g. /a/b <execute> + /a <read> => /a/b <execute + read>
 	 */
-	for (i = 0; i < rule->num_layers; i++) {
-		const struct landlock_layer *const layer = &rule->layers[i];
-		const u64 layer_level = BIT_ULL(layer->level - 1);
-
-		/* Checks that the layer grants access to the full request. */
-		if ((layer->access & access_request) == access_request) {
-			layer_mask &= ~layer_level;
+	for (layer_level = 0; layer_level < rule->num_layers; layer_level++) {
+		const struct landlock_layer *const layer =
+			&rule->layers[layer_level];
+		const layer_mask_t layer_bit = BIT_ULL(layer->level - 1);
+		const unsigned long access_req = access_request;
+		unsigned long access_bit;
+		bool is_empty;
 
-			if (layer_mask == 0)
-				return layer_mask;
+		/*
+		 * Records in @layer_masks which layer grants access to each
+		 * requested access.
+		 */
+		is_empty = true;
+		for_each_set_bit(access_bit, &access_req,
+				 ARRAY_SIZE(*layer_masks)) {
+			if (layer->access & BIT_ULL(access_bit))
+				(*layer_masks)[access_bit] &= ~layer_bit;
+			is_empty = is_empty && !(*layer_masks)[access_bit];
 		}
+		if (is_empty)
+			return true;
 	}
-	return layer_mask;
+	return false;
+}
+
+/*
+ * Allows access to pseudo filesystems that will never be mountable (e.g.
+ * sockfs, pipefs), but can still be reachable through
+ * /proc/<pid>/fd/<file-descriptor>
+ */
+static inline bool is_nouser_or_private(const struct dentry *dentry)
+{
+	return (dentry->d_sb->s_flags & SB_NOUSER) ||
+	       (d_is_positive(dentry) &&
+		unlikely(IS_PRIVATE(d_backing_inode(dentry))));
 }
 
 static int check_access_path(const struct landlock_ruleset *const domain,
-		const struct path *const path, u32 access_request)
+			     const struct path *const path,
+			     const access_mask_t access_request)
 {
-	bool allowed = false;
+	layer_mask_t layer_masks[LANDLOCK_NUM_ACCESS_FS] = {};
+	bool allowed = false, has_access = false;
 	struct path walker_path;
-	u64 layer_mask;
 	size_t i;
 
-	/* Make sure all layers can be checked. */
-	BUILD_BUG_ON(BITS_PER_TYPE(layer_mask) < LANDLOCK_MAX_NUM_LAYERS);
-
 	if (!access_request)
 		return 0;
 	if (WARN_ON_ONCE(!domain || !path))
 		return 0;
-	/*
-	 * Allows access to pseudo filesystems that will never be mountable
-	 * (e.g. sockfs, pipefs), but can still be reachable through
-	 * /proc/<pid>/fd/<file-descriptor> .
-	 */
-	if ((path->dentry->d_sb->s_flags & SB_NOUSER) ||
-			(d_is_positive(path->dentry) &&
-			 unlikely(IS_PRIVATE(d_backing_inode(path->dentry)))))
+	if (is_nouser_or_private(path->dentry))
 		return 0;
 	if (WARN_ON_ONCE(domain->num_layers < 1))
 		return -EACCES;
 
 	/* Saves all layers handling a subset of requested accesses. */
-	layer_mask = 0;
 	for (i = 0; i < domain->num_layers; i++) {
-		if (domain->fs_access_masks[i] & access_request)
-			layer_mask |= BIT_ULL(i);
+		const unsigned long access_req = access_request;
+		unsigned long access_bit;
+
+		for_each_set_bit(access_bit, &access_req,
+				 ARRAY_SIZE(layer_masks)) {
+			if (domain->fs_access_masks[i] & BIT_ULL(access_bit)) {
+				layer_masks[access_bit] |= BIT_ULL(i);
+				has_access = true;
+			}
+		}
 	}
 	/* An access request not handled by the domain is allowed. */
-	if (layer_mask == 0)
+	if (!has_access)
 		return 0;
 
 	walker_path = *path;
@@ -268,13 +317,11 @@
 	while (true) {
 		struct dentry *parent_dentry;
 
-		layer_mask = unmask_layers(domain, &walker_path,
-				access_request, layer_mask);
-		if (layer_mask == 0) {
+		allowed = unmask_layers(find_rule(domain, walker_path.dentry),
+					access_request, &layer_masks);
+		if (allowed)
 			/* Stops when a rule from each layer grants access. */
-			allowed = true;
 			break;
-		}
 
 jump_up:
 		if (walker_path.dentry == walker_path.mnt->mnt_root) {
@@ -308,7 +355,7 @@
 }
 
 static inline int current_check_access_path(const struct path *const path,
-		const u32 access_request)
+					    const access_mask_t access_request)
 {
 	const struct landlock_ruleset *const dom =
 		landlock_get_current_domain();
@@ -318,6 +365,38 @@
 	return check_access_path(dom, path, access_request);
 }
 
+static inline access_mask_t get_mode_access(const umode_t mode)
+{
+	switch (mode & S_IFMT) {
+	case S_IFLNK:
+		return LANDLOCK_ACCESS_FS_MAKE_SYM;
+	case S_IFDIR:
+		return LANDLOCK_ACCESS_FS_MAKE_DIR;
+	case S_IFCHR:
+		return LANDLOCK_ACCESS_FS_MAKE_CHAR;
+	case S_IFBLK:
+		return LANDLOCK_ACCESS_FS_MAKE_BLOCK;
+	case S_IFIFO:
+		return LANDLOCK_ACCESS_FS_MAKE_FIFO;
+	case S_IFSOCK:
+		return LANDLOCK_ACCESS_FS_MAKE_SOCK;
+	case S_IFREG:
+	case 0:
+		/* A zero mode translates to S_IFREG. */
+	default:
+		/* Treats weird files as regular files. */
+		return LANDLOCK_ACCESS_FS_MAKE_REG;
+	}
+}
+
+static inline access_mask_t maybe_remove(const struct dentry *const dentry)
+{
+	if (d_is_negative(dentry))
+		return 0;
+	return d_is_dir(dentry) ? LANDLOCK_ACCESS_FS_REMOVE_DIR :
+				  LANDLOCK_ACCESS_FS_REMOVE_FILE;
+}
+
 /* Inode hooks */
 
 static void hook_inode_free_security(struct inode *const inode)
@@ -436,8 +515,8 @@
 	if (prev_inode)
 		iput(prev_inode);
 	/* Waits for pending iput() in release_inode(). */
-	wait_var_event(&landlock_superblock(sb)->inode_refs, !atomic_long_read(
-				&landlock_superblock(sb)->inode_refs));
+	wait_var_event(&landlock_superblock(sb)->inode_refs,
+		       !atomic_long_read(&landlock_superblock(sb)->inode_refs));
 }
 
 /*
@@ -459,8 +538,8 @@
  * a dedicated user space option would be required (e.g. as a ruleset flag).
  */
 static int hook_sb_mount(const char *const dev_name,
-		const struct path *const path, const char *const type,
-		const unsigned long flags, void *const data)
+			 const struct path *const path, const char *const type,
+			 const unsigned long flags, void *const data)
 {
 	if (!landlock_get_current_domain())
 		return 0;
@@ -468,7 +547,7 @@
 }
 
 static int hook_move_mount(const struct path *const from_path,
-		const struct path *const to_path)
+			   const struct path *const to_path)
 {
 	if (!landlock_get_current_domain())
 		return 0;
@@ -502,7 +581,7 @@
  * view of the filesystem.
  */
 static int hook_sb_pivotroot(const struct path *const old_path,
-		const struct path *const new_path)
+			     const struct path *const new_path)
 {
 	if (!landlock_get_current_domain())
 		return 0;
@@ -511,31 +590,6 @@
 
 /* Path hooks */
 
-static inline u32 get_mode_access(const umode_t mode)
-{
-	switch (mode & S_IFMT) {
-	case S_IFLNK:
-		return LANDLOCK_ACCESS_FS_MAKE_SYM;
-	case 0:
-		/* A zero mode translates to S_IFREG. */
-	case S_IFREG:
-		return LANDLOCK_ACCESS_FS_MAKE_REG;
-	case S_IFDIR:
-		return LANDLOCK_ACCESS_FS_MAKE_DIR;
-	case S_IFCHR:
-		return LANDLOCK_ACCESS_FS_MAKE_CHAR;
-	case S_IFBLK:
-		return LANDLOCK_ACCESS_FS_MAKE_BLOCK;
-	case S_IFIFO:
-		return LANDLOCK_ACCESS_FS_MAKE_FIFO;
-	case S_IFSOCK:
-		return LANDLOCK_ACCESS_FS_MAKE_SOCK;
-	default:
-		WARN_ON_ONCE(1);
-		return 0;
-	}
-}
-
 /*
  * Creating multiple links or renaming may lead to privilege escalations if not
  * handled properly.  Indeed, we must be sure that the source doesn't gain more
@@ -545,8 +599,8 @@
  * deal with that.
  */
 static int hook_path_link(struct dentry *const old_dentry,
-		const struct path *const new_dir,
-		struct dentry *const new_dentry)
+			  const struct path *const new_dir,
+			  struct dentry *const new_dentry)
 {
 	const struct landlock_ruleset *const dom =
 		landlock_get_current_domain();
@@ -559,22 +613,15 @@
 		return -EXDEV;
 	if (unlikely(d_is_negative(old_dentry)))
 		return -ENOENT;
-	return check_access_path(dom, new_dir,
-			get_mode_access(d_backing_inode(old_dentry)->i_mode));
-}
-
-static inline u32 maybe_remove(const struct dentry *const dentry)
-{
-	if (d_is_negative(dentry))
-		return 0;
-	return d_is_dir(dentry) ? LANDLOCK_ACCESS_FS_REMOVE_DIR :
-		LANDLOCK_ACCESS_FS_REMOVE_FILE;
+	return check_access_path(
+		dom, new_dir,
+		get_mode_access(d_backing_inode(old_dentry)->i_mode));
 }
 
 static int hook_path_rename(const struct path *const old_dir,
-		struct dentry *const old_dentry,
-		const struct path *const new_dir,
-		struct dentry *const new_dentry)
+			    struct dentry *const old_dentry,
+			    const struct path *const new_dir,
+			    struct dentry *const new_dentry)
 {
 	const struct landlock_ruleset *const dom =
 		landlock_get_current_domain();
@@ -588,20 +635,21 @@
 	if (unlikely(d_is_negative(old_dentry)))
 		return -ENOENT;
 	/* RENAME_EXCHANGE is handled because directories are the same. */
-	return check_access_path(dom, old_dir, maybe_remove(old_dentry) |
-			maybe_remove(new_dentry) |
+	return check_access_path(
+		dom, old_dir,
+		maybe_remove(old_dentry) | maybe_remove(new_dentry) |
 			get_mode_access(d_backing_inode(old_dentry)->i_mode));
 }
 
 static int hook_path_mkdir(const struct path *const dir,
-		struct dentry *const dentry, const umode_t mode)
+			   struct dentry *const dentry, const umode_t mode)
 {
 	return current_check_access_path(dir, LANDLOCK_ACCESS_FS_MAKE_DIR);
 }
 
 static int hook_path_mknod(const struct path *const dir,
-		struct dentry *const dentry, const umode_t mode,
-		const unsigned int dev)
+			   struct dentry *const dentry, const umode_t mode,
+			   const unsigned int dev)
 {
 	const struct landlock_ruleset *const dom =
 		landlock_get_current_domain();
@@ -612,28 +660,29 @@
 }
 
 static int hook_path_symlink(const struct path *const dir,
-		struct dentry *const dentry, const char *const old_name)
+			     struct dentry *const dentry,
+			     const char *const old_name)
 {
 	return current_check_access_path(dir, LANDLOCK_ACCESS_FS_MAKE_SYM);
 }
 
 static int hook_path_unlink(const struct path *const dir,
-		struct dentry *const dentry)
+			    struct dentry *const dentry)
 {
 	return current_check_access_path(dir, LANDLOCK_ACCESS_FS_REMOVE_FILE);
 }
 
 static int hook_path_rmdir(const struct path *const dir,
-		struct dentry *const dentry)
+			   struct dentry *const dentry)
 {
 	return current_check_access_path(dir, LANDLOCK_ACCESS_FS_REMOVE_DIR);
 }
 
 /* File hooks */
 
-static inline u32 get_file_access(const struct file *const file)
+static inline access_mask_t get_file_access(const struct file *const file)
 {
-	u32 access = 0;
+	access_mask_t access = 0;
 
 	if (file->f_mode & FMODE_READ) {
 		/* A directory can only be opened in read mode. */
@@ -688,5 +737,5 @@
 __init void landlock_add_fs_hooks(void)
 {
 	security_add_hooks(landlock_hooks, ARRAY_SIZE(landlock_hooks),
-			LANDLOCK_NAME);
+			   &landlock_lsmid);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/fs.h
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/fs.h
@@ -50,14 +50,14 @@
 	atomic_long_t inode_refs;
 };
 
-static inline struct landlock_inode_security *landlock_inode(
-		const struct inode *const inode)
+static inline struct landlock_inode_security *
+landlock_inode(const struct inode *const inode)
 {
 	return inode->i_security + landlock_blob_sizes.lbs_inode;
 }
 
-static inline struct landlock_superblock_security *landlock_superblock(
-		const struct super_block *const superblock)
+static inline struct landlock_superblock_security *
+landlock_superblock(const struct super_block *const superblock)
 {
 	return superblock->s_security + landlock_blob_sizes.lbs_superblock;
 }
@@ -65,6 +65,7 @@
 __init void landlock_add_fs_hooks(void);
 
 int landlock_append_fs_rule(struct landlock_ruleset *const ruleset,
-		const struct path *const path, u32 access_hierarchy);
+			    const struct path *const path,
+			    access_mask_t access_hierarchy);
 
 #endif /* _SECURITY_LANDLOCK_FS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/limits.h
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/limits.h
@@ -9,13 +9,19 @@
 #ifndef _SECURITY_LANDLOCK_LIMITS_H
 #define _SECURITY_LANDLOCK_LIMITS_H
 
+#include <linux/bitops.h>
 #include <linux/limits.h>
 #include <uapi/linux/landlock.h>
 
-#define LANDLOCK_MAX_NUM_LAYERS		64
+/* clang-format off */
+
+#define LANDLOCK_MAX_NUM_LAYERS		16
 #define LANDLOCK_MAX_NUM_RULES		U32_MAX
 
 #define LANDLOCK_LAST_ACCESS_FS		LANDLOCK_ACCESS_FS_MAKE_SYM
 #define LANDLOCK_MASK_ACCESS_FS		((LANDLOCK_LAST_ACCESS_FS << 1) - 1)
+#define LANDLOCK_NUM_ACCESS_FS		__const_hweight64(LANDLOCK_MASK_ACCESS_FS)
+
+/* clang-format on */
 
 #endif /* _SECURITY_LANDLOCK_LIMITS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/object.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/object.c
@@ -17,9 +17,9 @@
 
 #include "object.h"
 
-struct landlock_object *landlock_create_object(
-		const struct landlock_object_underops *const underops,
-		void *const underobj)
+struct landlock_object *
+landlock_create_object(const struct landlock_object_underops *const underops,
+		       void *const underobj)
 {
 	struct landlock_object *new_object;
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/object.h
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/object.h
@@ -76,9 +76,9 @@
 	};
 };
 
-struct landlock_object *landlock_create_object(
-		const struct landlock_object_underops *const underops,
-		void *const underobj);
+struct landlock_object *
+landlock_create_object(const struct landlock_object_underops *const underops,
+		       void *const underobj);
 
 void landlock_put_object(struct landlock_object *const object);
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/ptrace.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/ptrace.c
@@ -30,7 +30,7 @@
  * means a subset of) the @child domain.
  */
 static bool domain_scope_le(const struct landlock_ruleset *const parent,
-		const struct landlock_ruleset *const child)
+			    const struct landlock_ruleset *const child)
 {
 	const struct landlock_hierarchy *walker;
 
@@ -48,7 +48,7 @@
 }
 
 static bool task_is_scoped(const struct task_struct *const parent,
-		const struct task_struct *const child)
+			   const struct task_struct *const child)
 {
 	bool is_scoped;
 	const struct landlock_ruleset *dom_parent, *dom_child;
@@ -62,7 +62,7 @@
 }
 
 static int task_ptrace(const struct task_struct *const parent,
-		const struct task_struct *const child)
+		       const struct task_struct *const child)
 {
 	/* Quick return for non-landlocked tasks. */
 	if (!landlocked(parent))
@@ -86,7 +86,7 @@
  * granted, -errno if denied.
  */
 static int hook_ptrace_access_check(struct task_struct *const child,
-		const unsigned int mode)
+				    const unsigned int mode)
 {
 	return task_ptrace(current, child);
 }
@@ -116,5 +116,5 @@
 __init void landlock_add_ptrace_hooks(void)
 {
 	security_add_hooks(landlock_hooks, ARRAY_SIZE(landlock_hooks),
-			LANDLOCK_NAME);
+			   &landlock_lsmid);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/ruleset.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/ruleset.c
@@ -28,8 +28,9 @@
 {
 	struct landlock_ruleset *new_ruleset;
 
-	new_ruleset = kzalloc(struct_size(new_ruleset, fs_access_masks,
-				num_layers), GFP_KERNEL_ACCOUNT);
+	new_ruleset =
+		kzalloc(struct_size(new_ruleset, fs_access_masks, num_layers),
+			GFP_KERNEL_ACCOUNT);
 	if (!new_ruleset)
 		return ERR_PTR(-ENOMEM);
 	refcount_set(&new_ruleset->usage, 1);
@@ -44,7 +45,8 @@
 	return new_ruleset;
 }
 
-struct landlock_ruleset *landlock_create_ruleset(const u32 fs_access_mask)
+struct landlock_ruleset *
+landlock_create_ruleset(const access_mask_t fs_access_mask)
 {
 	struct landlock_ruleset *new_ruleset;
 
@@ -66,11 +68,10 @@
 	BUILD_BUG_ON(rule.num_layers < LANDLOCK_MAX_NUM_LAYERS);
 }
 
-static struct landlock_rule *create_rule(
-		struct landlock_object *const object,
-		const struct landlock_layer (*const layers)[],
-		const u32 num_layers,
-		const struct landlock_layer *const new_layer)
+static struct landlock_rule *
+create_rule(struct landlock_object *const object,
+	    const struct landlock_layer (*const layers)[], const u32 num_layers,
+	    const struct landlock_layer *const new_layer)
 {
 	struct landlock_rule *new_rule;
 	u32 new_num_layers;
@@ -85,7 +86,7 @@
 		new_num_layers = num_layers;
 	}
 	new_rule = kzalloc(struct_size(new_rule, layers, new_num_layers),
-			GFP_KERNEL_ACCOUNT);
+			   GFP_KERNEL_ACCOUNT);
 	if (!new_rule)
 		return ERR_PTR(-ENOMEM);
 	RB_CLEAR_NODE(&new_rule->node);
@@ -94,7 +95,7 @@
 	new_rule->num_layers = new_num_layers;
 	/* Copies the original layer stack. */
 	memcpy(new_rule->layers, layers,
-			flex_array_size(new_rule, layers, num_layers));
+	       flex_array_size(new_rule, layers, num_layers));
 	if (new_layer)
 		/* Adds a copy of @new_layer on the layer stack. */
 		new_rule->layers[new_rule->num_layers - 1] = *new_layer;
@@ -142,9 +143,9 @@
  * access rights.
  */
 static int insert_rule(struct landlock_ruleset *const ruleset,
-		struct landlock_object *const object,
-		const struct landlock_layer (*const layers)[],
-		size_t num_layers)
+		       struct landlock_object *const object,
+		       const struct landlock_layer (*const layers)[],
+		       size_t num_layers)
 {
 	struct rb_node **walker_node;
 	struct rb_node *parent_node = NULL;
@@ -156,8 +157,8 @@
 		return -ENOENT;
 	walker_node = &(ruleset->root.rb_node);
 	while (*walker_node) {
-		struct landlock_rule *const this = rb_entry(*walker_node,
-				struct landlock_rule, node);
+		struct landlock_rule *const this =
+			rb_entry(*walker_node, struct landlock_rule, node);
 
 		if (this->object != object) {
 			parent_node = *walker_node;
@@ -194,7 +195,7 @@
 		 * ruleset and a domain.
 		 */
 		new_rule = create_rule(object, &this->layers, this->num_layers,
-				&(*layers)[0]);
+				       &(*layers)[0]);
 		if (IS_ERR(new_rule))
 			return PTR_ERR(new_rule);
 		rb_replace_node(&this->node, &new_rule->node, &ruleset->root);
@@ -228,13 +229,14 @@
 
 /* @ruleset must be locked by the caller. */
 int landlock_insert_rule(struct landlock_ruleset *const ruleset,
-		struct landlock_object *const object, const u32 access)
+			 struct landlock_object *const object,
+			 const access_mask_t access)
 {
-	struct landlock_layer layers[] = {{
+	struct landlock_layer layers[] = { {
 		.access = access,
 		/* When @level is zero, insert_rule() extends @ruleset. */
 		.level = 0,
-	}};
+	} };
 
 	build_check_layer();
 	return insert_rule(ruleset, object, &layers, ARRAY_SIZE(layers));
@@ -257,7 +259,7 @@
 }
 
 static int merge_ruleset(struct landlock_ruleset *const dst,
-		struct landlock_ruleset *const src)
+			 struct landlock_ruleset *const src)
 {
 	struct landlock_rule *walker_rule, *next_rule;
 	int err = 0;
@@ -282,11 +284,11 @@
 	dst->fs_access_masks[dst->num_layers - 1] = src->fs_access_masks[0];
 
 	/* Merges the @src tree. */
-	rbtree_postorder_for_each_entry_safe(walker_rule, next_rule,
-			&src->root, node) {
-		struct landlock_layer layers[] = {{
+	rbtree_postorder_for_each_entry_safe(walker_rule, next_rule, &src->root,
+					     node) {
+		struct landlock_layer layers[] = { {
 			.level = dst->num_layers,
-		}};
+		} };
 
 		if (WARN_ON_ONCE(walker_rule->num_layers != 1)) {
 			err = -EINVAL;
@@ -298,7 +300,7 @@
 		}
 		layers[0].access = walker_rule->layers[0].access;
 		err = insert_rule(dst, walker_rule->object, &layers,
-				ARRAY_SIZE(layers));
+				  ARRAY_SIZE(layers));
 		if (err)
 			goto out_unlock;
 	}
@@ -310,7 +312,7 @@
 }
 
 static int inherit_ruleset(struct landlock_ruleset *const parent,
-		struct landlock_ruleset *const child)
+			   struct landlock_ruleset *const child)
 {
 	struct landlock_rule *walker_rule, *next_rule;
 	int err = 0;
@@ -325,9 +327,10 @@
 
 	/* Copies the @parent tree. */
 	rbtree_postorder_for_each_entry_safe(walker_rule, next_rule,
-			&parent->root, node) {
+					     &parent->root, node) {
 		err = insert_rule(child, walker_rule->object,
-				&walker_rule->layers, walker_rule->num_layers);
+				  &walker_rule->layers,
+				  walker_rule->num_layers);
 		if (err)
 			goto out_unlock;
 	}
@@ -338,7 +341,7 @@
 	}
 	/* Copies the parent layer stack and leaves a space for the new layer. */
 	memcpy(child->fs_access_masks, parent->fs_access_masks,
-			flex_array_size(parent, fs_access_masks, parent->num_layers));
+	       flex_array_size(parent, fs_access_masks, parent->num_layers));
 
 	if (WARN_ON_ONCE(!parent->hierarchy)) {
 		err = -EINVAL;
@@ -358,8 +361,7 @@
 	struct landlock_rule *freeme, *next;
 
 	might_sleep();
-	rbtree_postorder_for_each_entry_safe(freeme, next, &ruleset->root,
-			node)
+	rbtree_postorder_for_each_entry_safe(freeme, next, &ruleset->root, node)
 		free_rule(freeme);
 	put_hierarchy(ruleset->hierarchy);
 	kfree(ruleset);
@@ -397,9 +399,9 @@
  * Returns the intersection of @parent and @ruleset, or returns @parent if
  * @ruleset is empty, or returns a duplicate of @ruleset if @parent is empty.
  */
-struct landlock_ruleset *landlock_merge_ruleset(
-		struct landlock_ruleset *const parent,
-		struct landlock_ruleset *const ruleset)
+struct landlock_ruleset *
+landlock_merge_ruleset(struct landlock_ruleset *const parent,
+		       struct landlock_ruleset *const ruleset)
 {
 	struct landlock_ruleset *new_dom;
 	u32 num_layers;
@@ -421,8 +423,8 @@
 	new_dom = create_ruleset(num_layers);
 	if (IS_ERR(new_dom))
 		return new_dom;
-	new_dom->hierarchy = kzalloc(sizeof(*new_dom->hierarchy),
-			GFP_KERNEL_ACCOUNT);
+	new_dom->hierarchy =
+		kzalloc(sizeof(*new_dom->hierarchy), GFP_KERNEL_ACCOUNT);
 	if (!new_dom->hierarchy) {
 		err = -ENOMEM;
 		goto out_put_dom;
@@ -449,9 +451,9 @@
 /*
  * The returned access has the same lifetime as @ruleset.
  */
-const struct landlock_rule *landlock_find_rule(
-		const struct landlock_ruleset *const ruleset,
-		const struct landlock_object *const object)
+const struct landlock_rule *
+landlock_find_rule(const struct landlock_ruleset *const ruleset,
+		   const struct landlock_object *const object)
 {
 	const struct rb_node *node;
 
@@ -459,8 +461,8 @@
 		return NULL;
 	node = ruleset->root.rb_node;
 	while (node) {
-		struct landlock_rule *this = rb_entry(node,
-				struct landlock_rule, node);
+		struct landlock_rule *this =
+			rb_entry(node, struct landlock_rule, node);
 
 		if (this->object == object)
 			return this;
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/ruleset.h
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/ruleset.h
@@ -9,13 +9,26 @@
 #ifndef _SECURITY_LANDLOCK_RULESET_H
 #define _SECURITY_LANDLOCK_RULESET_H
 
+#include <linux/bitops.h>
+#include <linux/build_bug.h>
 #include <linux/mutex.h>
 #include <linux/rbtree.h>
 #include <linux/refcount.h>
 #include <linux/workqueue.h>
 
+#include "limits.h"
 #include "object.h"
 
+typedef u16 access_mask_t;
+/* Makes sure all filesystem access rights can be stored. */
+static_assert(BITS_PER_TYPE(access_mask_t) >= LANDLOCK_NUM_ACCESS_FS);
+/* Makes sure for_each_set_bit() and for_each_clear_bit() calls are OK. */
+static_assert(sizeof(unsigned long) >= sizeof(access_mask_t));
+
+typedef u16 layer_mask_t;
+/* Makes sure all layers can be checked. */
+static_assert(BITS_PER_TYPE(layer_mask_t) >= LANDLOCK_MAX_NUM_LAYERS);
+
 /**
  * struct landlock_layer - Access rights for a given layer
  */
@@ -28,7 +41,7 @@
 	 * @access: Bitfield of allowed actions on the kernel object.  They are
 	 * relative to the object type (e.g. %LANDLOCK_ACTION_FS_READ).
 	 */
-	u16 access;
+	access_mask_t access;
 };
 
 /**
@@ -135,26 +148,28 @@
 			 * layers are set once and never changed for the
 			 * lifetime of the ruleset.
 			 */
-			u16 fs_access_masks[];
+			access_mask_t fs_access_masks[];
 		};
 	};
 };
 
-struct landlock_ruleset *landlock_create_ruleset(const u32 fs_access_mask);
+struct landlock_ruleset *
+landlock_create_ruleset(const access_mask_t fs_access_mask);
 
 void landlock_put_ruleset(struct landlock_ruleset *const ruleset);
 void landlock_put_ruleset_deferred(struct landlock_ruleset *const ruleset);
 
 int landlock_insert_rule(struct landlock_ruleset *const ruleset,
-		struct landlock_object *const object, const u32 access);
+			 struct landlock_object *const object,
+			 const access_mask_t access);
 
-struct landlock_ruleset *landlock_merge_ruleset(
-		struct landlock_ruleset *const parent,
-		struct landlock_ruleset *const ruleset);
-
-const struct landlock_rule *landlock_find_rule(
-		const struct landlock_ruleset *const ruleset,
-		const struct landlock_object *const object);
+struct landlock_ruleset *
+landlock_merge_ruleset(struct landlock_ruleset *const parent,
+		       struct landlock_ruleset *const ruleset);
+
+const struct landlock_rule *
+landlock_find_rule(const struct landlock_ruleset *const ruleset,
+		   const struct landlock_object *const object);
 
 static inline void landlock_get_ruleset(struct landlock_ruleset *const ruleset)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/setup.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/setup.c
@@ -23,6 +23,11 @@
 	.lbs_superblock = sizeof(struct landlock_superblock_security),
 };
 
+struct lsm_id landlock_lsmid __lsm_ro_after_init = {
+	.lsm = LANDLOCK_NAME,
+	.slot = LSMBLOB_NOT_NEEDED,
+};
+
 static int __init landlock_init(void)
 {
 	landlock_add_cred_hooks();
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/setup.h
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/setup.h
@@ -14,5 +14,6 @@
 extern bool landlock_initialized;
 
 extern struct lsm_blob_sizes landlock_blob_sizes;
+extern struct lsm_id landlock_lsmid;
 
 #endif /* _SECURITY_LANDLOCK_SETUP_H */
--- linux-xilinx-zynqmp-5.15.0.orig/security/landlock/syscalls.c
+++ linux-xilinx-zynqmp-5.15.0/security/landlock/syscalls.c
@@ -32,6 +32,18 @@
 #include "ruleset.h"
 #include "setup.h"
 
+static bool is_initialized(void)
+{
+	if (likely(landlock_initialized))
+		return true;
+
+	pr_warn_once(
+		"Disabled but requested by user space. "
+		"You should enable Landlock at boot time: "
+		"https://docs.kernel.org/userspace-api/landlock.html#boot-time-configuration\n");
+	return false;
+}
+
 /**
  * copy_min_struct_from_user - Safe future-proof argument copying
  *
@@ -43,9 +55,10 @@
  * @src: User space pointer or NULL.
  * @usize: (Alleged) size of the data pointed to by @src.
  */
-static __always_inline int copy_min_struct_from_user(void *const dst,
-		const size_t ksize, const size_t ksize_min,
-		const void __user *const src, const size_t usize)
+static __always_inline int
+copy_min_struct_from_user(void *const dst, const size_t ksize,
+			  const size_t ksize_min, const void __user *const src,
+			  const size_t usize)
 {
 	/* Checks buffer inconsistencies. */
 	BUILD_BUG_ON(!dst);
@@ -93,7 +106,7 @@
 /* Ruleset handling */
 
 static int fop_ruleset_release(struct inode *const inode,
-		struct file *const filp)
+			       struct file *const filp)
 {
 	struct landlock_ruleset *ruleset = filp->private_data;
 
@@ -102,15 +115,15 @@
 }
 
 static ssize_t fop_dummy_read(struct file *const filp, char __user *const buf,
-		const size_t size, loff_t *const ppos)
+			      const size_t size, loff_t *const ppos)
 {
 	/* Dummy handler to enable FMODE_CAN_READ. */
 	return -EINVAL;
 }
 
 static ssize_t fop_dummy_write(struct file *const filp,
-		const char __user *const buf, const size_t size,
-		loff_t *const ppos)
+			       const char __user *const buf, const size_t size,
+			       loff_t *const ppos)
 {
 	/* Dummy handler to enable FMODE_CAN_WRITE. */
 	return -EINVAL;
@@ -128,7 +141,7 @@
 	.write = fop_dummy_write,
 };
 
-#define LANDLOCK_ABI_VERSION	1
+#define LANDLOCK_ABI_VERSION 1
 
 /**
  * sys_landlock_create_ruleset - Create a new ruleset
@@ -164,26 +177,27 @@
 	/* Build-time checks. */
 	build_check_abi();
 
-	if (!landlock_initialized)
+	if (!is_initialized())
 		return -EOPNOTSUPP;
 
 	if (flags) {
-		if ((flags == LANDLOCK_CREATE_RULESET_VERSION)
-				&& !attr && !size)
+		if ((flags == LANDLOCK_CREATE_RULESET_VERSION) && !attr &&
+		    !size)
 			return LANDLOCK_ABI_VERSION;
 		return -EINVAL;
 	}
 
 	/* Copies raw user space buffer. */
 	err = copy_min_struct_from_user(&ruleset_attr, sizeof(ruleset_attr),
-			offsetofend(typeof(ruleset_attr), handled_access_fs),
-			attr, size);
+					offsetofend(typeof(ruleset_attr),
+						    handled_access_fs),
+					attr, size);
 	if (err)
 		return err;
 
 	/* Checks content (and 32-bits cast). */
 	if ((ruleset_attr.handled_access_fs | LANDLOCK_MASK_ACCESS_FS) !=
-			LANDLOCK_MASK_ACCESS_FS)
+	    LANDLOCK_MASK_ACCESS_FS)
 		return -EINVAL;
 
 	/* Checks arguments and transforms to kernel struct. */
@@ -192,8 +206,8 @@
 		return PTR_ERR(ruleset);
 
 	/* Creates anonymous FD referring to the ruleset. */
-	ruleset_fd = anon_inode_getfd("landlock-ruleset", &ruleset_fops,
-			ruleset, O_RDWR | O_CLOEXEC);
+	ruleset_fd = anon_inode_getfd("[landlock-ruleset]", &ruleset_fops,
+				      ruleset, O_RDWR | O_CLOEXEC);
 	if (ruleset_fd < 0)
 		landlock_put_ruleset(ruleset);
 	return ruleset_fd;
@@ -204,7 +218,7 @@
  * landlock_put_ruleset() on the return value.
  */
 static struct landlock_ruleset *get_ruleset_from_fd(const int fd,
-		const fmode_t mode)
+						    const fmode_t mode)
 {
 	struct fd ruleset_f;
 	struct landlock_ruleset *ruleset;
@@ -244,8 +258,8 @@
 	struct fd f;
 	int err = 0;
 
-	BUILD_BUG_ON(!__same_type(fd,
-		((struct landlock_path_beneath_attr *)NULL)->parent_fd));
+	BUILD_BUG_ON(!__same_type(
+		fd, ((struct landlock_path_beneath_attr *)NULL)->parent_fd));
 
 	/* Handles O_PATH. */
 	f = fdget_raw(fd);
@@ -257,10 +271,10 @@
 	 * pipefs).
 	 */
 	if ((f.file->f_op == &ruleset_fops) ||
-			(f.file->f_path.mnt->mnt_flags & MNT_INTERNAL) ||
-			(f.file->f_path.dentry->d_sb->s_flags & SB_NOUSER) ||
-			d_is_negative(f.file->f_path.dentry) ||
-			IS_PRIVATE(d_backing_inode(f.file->f_path.dentry))) {
+	    (f.file->f_path.mnt->mnt_flags & MNT_INTERNAL) ||
+	    (f.file->f_path.dentry->d_sb->s_flags & SB_NOUSER) ||
+	    d_is_negative(f.file->f_path.dentry) ||
+	    IS_PRIVATE(d_backing_inode(f.file->f_path.dentry))) {
 		err = -EBADFD;
 		goto out_fdput;
 	}
@@ -290,19 +304,18 @@
  *
  * - EOPNOTSUPP: Landlock is supported by the kernel but disabled at boot time;
  * - EINVAL: @flags is not 0, or inconsistent access in the rule (i.e.
- *   &landlock_path_beneath_attr.allowed_access is not a subset of the rule's
- *   accesses);
+ *   &landlock_path_beneath_attr.allowed_access is not a subset of the
+ *   ruleset handled accesses);
  * - ENOMSG: Empty accesses (e.g. &landlock_path_beneath_attr.allowed_access);
  * - EBADF: @ruleset_fd is not a file descriptor for the current thread, or a
  *   member of @rule_attr is not a file descriptor as expected;
  * - EBADFD: @ruleset_fd is not a ruleset file descriptor, or a member of
- *   @rule_attr is not the expected file descriptor type (e.g. file open
- *   without O_PATH);
+ *   @rule_attr is not the expected file descriptor type;
  * - EPERM: @ruleset_fd has no write access to the underlying ruleset;
  * - EFAULT: @rule_attr inconsistency.
  */
-SYSCALL_DEFINE4(landlock_add_rule,
-		const int, ruleset_fd, const enum landlock_rule_type, rule_type,
+SYSCALL_DEFINE4(landlock_add_rule, const int, ruleset_fd,
+		const enum landlock_rule_type, rule_type,
 		const void __user *const, rule_attr, const __u32, flags)
 {
 	struct landlock_path_beneath_attr path_beneath_attr;
@@ -310,27 +323,31 @@
 	struct landlock_ruleset *ruleset;
 	int res, err;
 
-	if (!landlock_initialized)
+	if (!is_initialized())
 		return -EOPNOTSUPP;
 
 	/* No flag for now. */
 	if (flags)
 		return -EINVAL;
 
-	if (rule_type != LANDLOCK_RULE_PATH_BENEATH)
-		return -EINVAL;
-
-	/* Copies raw user space buffer, only one type for now. */
-	res = copy_from_user(&path_beneath_attr, rule_attr,
-			sizeof(path_beneath_attr));
-	if (res)
-		return -EFAULT;
-
 	/* Gets and checks the ruleset. */
 	ruleset = get_ruleset_from_fd(ruleset_fd, FMODE_CAN_WRITE);
 	if (IS_ERR(ruleset))
 		return PTR_ERR(ruleset);
 
+	if (rule_type != LANDLOCK_RULE_PATH_BENEATH) {
+		err = -EINVAL;
+		goto out_put_ruleset;
+	}
+
+	/* Copies raw user space buffer, only one type for now. */
+	res = copy_from_user(&path_beneath_attr, rule_attr,
+			     sizeof(path_beneath_attr));
+	if (res) {
+		err = -EFAULT;
+		goto out_put_ruleset;
+	}
+
 	/*
 	 * Informs about useless rule: empty allowed_access (i.e. deny rules)
 	 * are ignored in path walks.
@@ -344,7 +361,7 @@
 	 * (ruleset->fs_access_masks[0] is automatically upgraded to 64-bits).
 	 */
 	if ((path_beneath_attr.allowed_access | ruleset->fs_access_masks[0]) !=
-			ruleset->fs_access_masks[0]) {
+	    ruleset->fs_access_masks[0]) {
 		err = -EINVAL;
 		goto out_put_ruleset;
 	}
@@ -356,7 +373,7 @@
 
 	/* Imports the new rule. */
 	err = landlock_append_fs_rule(ruleset, &path,
-			path_beneath_attr.allowed_access);
+				      path_beneath_attr.allowed_access);
 	path_put(&path);
 
 out_put_ruleset:
@@ -389,29 +406,29 @@
  * - E2BIG: The maximum number of stacked rulesets is reached for the current
  *   thread.
  */
-SYSCALL_DEFINE2(landlock_restrict_self,
-		const int, ruleset_fd, const __u32, flags)
+SYSCALL_DEFINE2(landlock_restrict_self, const int, ruleset_fd, const __u32,
+		flags)
 {
 	struct landlock_ruleset *new_dom, *ruleset;
 	struct cred *new_cred;
 	struct landlock_cred_security *new_llcred;
 	int err;
 
-	if (!landlock_initialized)
+	if (!is_initialized())
 		return -EOPNOTSUPP;
 
-	/* No flag for now. */
-	if (flags)
-		return -EINVAL;
-
 	/*
 	 * Similar checks as for seccomp(2), except that an -EPERM may be
 	 * returned.
 	 */
 	if (!task_no_new_privs(current) &&
-			!ns_capable_noaudit(current_user_ns(), CAP_SYS_ADMIN))
+	    !ns_capable_noaudit(current_user_ns(), CAP_SYS_ADMIN))
 		return -EPERM;
 
+	/* No flag for now. */
+	if (flags)
+		return -EINVAL;
+
 	/* Gets and checks the ruleset. */
 	ruleset = get_ruleset_from_fd(ruleset_fd, FMODE_CAN_READ);
 	if (IS_ERR(ruleset))
--- linux-xilinx-zynqmp-5.15.0.orig/security/loadpin/loadpin.c
+++ linux-xilinx-zynqmp-5.15.0/security/loadpin/loadpin.c
@@ -118,21 +118,11 @@
 	}
 }
 
-static int loadpin_read_file(struct file *file, enum kernel_read_file_id id,
-			     bool contents)
+static int loadpin_check(struct file *file, enum kernel_read_file_id id)
 {
 	struct super_block *load_root;
 	const char *origin = kernel_read_file_id_str(id);
 
-	/*
-	 * If we will not know that we'll be seeing the full contents
-	 * then we cannot trust a load will be complete and unchanged
-	 * off disk. Treat all contents=false hooks as if there were
-	 * no associated file struct.
-	 */
-	if (!contents)
-		file = NULL;
-
 	/* If the file id is excluded, ignore the pinning. */
 	if ((unsigned int)id < ARRAY_SIZE(ignore_read_file_id) &&
 	    ignore_read_file_id[id]) {
@@ -187,11 +177,32 @@
 	return 0;
 }
 
+static int loadpin_read_file(struct file *file, enum kernel_read_file_id id,
+			     bool contents)
+{
+	/*
+	 * LoadPin only cares about the _origin_ of a file, not its
+	 * contents, so we can ignore the "are full contents available"
+	 * argument here.
+	 */
+	return loadpin_check(file, id);
+}
+
 static int loadpin_load_data(enum kernel_load_data_id id, bool contents)
 {
-	return loadpin_read_file(NULL, (enum kernel_read_file_id) id, contents);
+	/*
+	 * LoadPin only cares about the _origin_ of a file, not its
+	 * contents, so a NULL file is passed, and we can ignore the
+	 * state of "contents".
+	 */
+	return loadpin_check(NULL, (enum kernel_read_file_id) id);
 }
 
+static struct lsm_id loadpin_lsmid __lsm_ro_after_init = {
+	.lsm  = "loadpin",
+	.slot = LSMBLOB_NOT_NEEDED
+};
+
 static struct security_hook_list loadpin_hooks[] __lsm_ro_after_init = {
 	LSM_HOOK_INIT(sb_free_security, loadpin_sb_free_security),
 	LSM_HOOK_INIT(kernel_read_file, loadpin_read_file),
@@ -239,7 +250,8 @@
 	pr_info("ready to pin (currently %senforcing)\n",
 		enforce ? "" : "not ");
 	parse_exclude();
-	security_add_hooks(loadpin_hooks, ARRAY_SIZE(loadpin_hooks), "loadpin");
+	security_add_hooks(loadpin_hooks, ARRAY_SIZE(loadpin_hooks),
+			   &loadpin_lsmid);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/lockdown/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/security/lockdown/Kconfig
@@ -16,6 +16,19 @@
 	  subsystem is fully initialised. If enabled, lockdown will
 	  unconditionally be called before any other LSMs.
 
+config LOCK_DOWN_IN_SECURE_BOOT
+	bool "Lock down the kernel in Secure Boot mode"
+	default n
+	depends on (EFI || S390 || PPC) && SECURITY_LOCKDOWN_LSM_EARLY
+	help
+	  Secure Boot provides a mechanism for ensuring that the firmware will
+	  only load signed bootloaders and kernels.  Secure boot mode
+	  determination is platform-specific; examples include EFI secure boot
+	  and SIPL on s390.
+
+	  Enabling this option results in kernel lockdown being triggered if
+	  booted under secure boot.
+
 choice
 	prompt "Kernel default lockdown mode"
 	default LOCK_DOWN_KERNEL_FORCE_NONE
--- linux-xilinx-zynqmp-5.15.0.orig/security/lockdown/lockdown.c
+++ linux-xilinx-zynqmp-5.15.0/security/lockdown/lockdown.c
@@ -73,6 +73,12 @@
 
 static struct security_hook_list lockdown_hooks[] __lsm_ro_after_init = {
 	LSM_HOOK_INIT(locked_down, lockdown_is_locked_down),
+	LSM_HOOK_INIT(lock_kernel_down, lock_kernel_down),
+};
+
+static struct lsm_id lockdown_lsmid __lsm_ro_after_init = {
+	.lsm = "lockdown",
+	.slot = LSMBLOB_NOT_NEEDED
 };
 
 static int __init lockdown_lsm_init(void)
@@ -83,7 +89,7 @@
 	lock_kernel_down("Kernel configuration", LOCKDOWN_CONFIDENTIALITY_MAX);
 #endif
 	security_add_hooks(lockdown_hooks, ARRAY_SIZE(lockdown_hooks),
-			   "lockdown");
+			   &lockdown_lsmid);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/safesetid/lsm.c
+++ linux-xilinx-zynqmp-5.15.0/security/safesetid/lsm.c
@@ -241,6 +241,11 @@
 	return -EACCES;
 }
 
+static struct lsm_id safesetid_lsmid __lsm_ro_after_init = {
+	.lsm  = "safesetid",
+	.slot = LSMBLOB_NOT_NEEDED
+};
+
 static struct security_hook_list safesetid_security_hooks[] = {
 	LSM_HOOK_INIT(task_fix_setuid, safesetid_task_fix_setuid),
 	LSM_HOOK_INIT(task_fix_setgid, safesetid_task_fix_setgid),
@@ -250,7 +255,8 @@
 static int __init safesetid_security_init(void)
 {
 	security_add_hooks(safesetid_security_hooks,
-			   ARRAY_SIZE(safesetid_security_hooks), "safesetid");
+			   ARRAY_SIZE(safesetid_security_hooks),
+			   &safesetid_lsmid);
 
 	/* Report that SafeSetID successfully initialized */
 	safesetid_initialized = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/security/safesetid/securityfs.c
+++ linux-xilinx-zynqmp-5.15.0/security/safesetid/securityfs.c
@@ -143,6 +143,9 @@
 	char *buf, *p, *end;
 	int err;
 
+	if (len >= KMALLOC_MAX_SIZE)
+		return -EINVAL;
+
 	pol = kmalloc(sizeof(struct setid_ruleset), GFP_KERNEL);
 	if (!pol)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/security/security.c
+++ linux-xilinx-zynqmp-5.15.0/security/security.c
@@ -29,6 +29,7 @@
 #include <linux/string.h>
 #include <linux/msg.h>
 #include <net/flow.h>
+#include <net/sock.h>
 
 #define MAX_LSM_EVM_XATTR	2
 
@@ -59,6 +60,7 @@
 	[LOCKDOWN_DEBUGFS] = "debugfs access",
 	[LOCKDOWN_XMON_WR] = "xmon write access",
 	[LOCKDOWN_BPF_WRITE_USER] = "use of bpf to write user RAM",
+	[LOCKDOWN_KGDB] = "KDB or KGDB access",
 	[LOCKDOWN_INTEGRITY_MAX] = "integrity",
 	[LOCKDOWN_KCORE] = "/proc/kcore access",
 	[LOCKDOWN_KPROBES] = "use of kprobes",
@@ -77,7 +79,14 @@
 static struct kmem_cache *lsm_inode_cache;
 
 char *lsm_names;
-static struct lsm_blob_sizes blob_sizes __lsm_ro_after_init;
+
+/*
+ * The task blob includes the "display" slot used for
+ * chosing which module presents contexts.
+ */
+static struct lsm_blob_sizes blob_sizes __lsm_ro_after_init = {
+	.lbs_task = sizeof(int),
+};
 
 /* Boot-time LSM user choice */
 static __initdata const char *chosen_lsm_order;
@@ -205,6 +214,7 @@
 	lsm_set_blob_size(&needed->lbs_ipc, &blob_sizes.lbs_ipc);
 	lsm_set_blob_size(&needed->lbs_msg_msg, &blob_sizes.lbs_msg_msg);
 	lsm_set_blob_size(&needed->lbs_superblock, &blob_sizes.lbs_superblock);
+	lsm_set_blob_size(&needed->lbs_sock, &blob_sizes.lbs_sock);
 	lsm_set_blob_size(&needed->lbs_task, &blob_sizes.lbs_task);
 }
 
@@ -341,7 +351,9 @@
 	init_debug("ipc blob size        = %d\n", blob_sizes.lbs_ipc);
 	init_debug("msg_msg blob size    = %d\n", blob_sizes.lbs_msg_msg);
 	init_debug("superblock blob size = %d\n", blob_sizes.lbs_superblock);
+	init_debug("sock blob size       = %d\n", blob_sizes.lbs_sock);
 	init_debug("task blob size       = %d\n", blob_sizes.lbs_task);
+	init_debug("lsmblob size       = %zu\n", sizeof(struct lsmblob));
 
 	/*
 	 * Create any kmem_caches needed for blobs
@@ -469,21 +481,63 @@
 	return 0;
 }
 
+/*
+ * Current index to use while initializing the lsmblob secid list.
+ * Pointers to the LSM id structures for local use.
+ */
+static int lsm_slot __lsm_ro_after_init;
+static struct lsm_id *lsm_slotlist[LSMBLOB_ENTRIES] __lsm_ro_after_init;
+
+/**
+ * security_lsm_slot_name - Get the name of the security module in a slot
+ * @slot: index into the "display" slot list.
+ *
+ * Provide the name of the security module associated with
+ * a display slot.
+ *
+ * If @slot is LSMBLOB_INVALID return the value
+ * for slot 0 if it has been set, otherwise NULL.
+ *
+ * Returns a pointer to the name string or NULL.
+ */
+const char *security_lsm_slot_name(int slot)
+{
+	if (slot == LSMBLOB_INVALID)
+		slot = 0;
+	else if (slot >= LSMBLOB_ENTRIES || slot < 0)
+		return NULL;
+
+	if (lsm_slotlist[slot] == NULL)
+		return NULL;
+	return lsm_slotlist[slot]->lsm;
+}
+
 /**
  * security_add_hooks - Add a modules hooks to the hook lists.
  * @hooks: the hooks to add
  * @count: the number of hooks to add
- * @lsm: the name of the security module
+ * @lsmid: the the identification information for the security module
  *
  * Each LSM has to register its hooks with the infrastructure.
+ * If the LSM is using hooks that export secids allocate a slot
+ * for it in the lsmblob.
  */
 void __init security_add_hooks(struct security_hook_list *hooks, int count,
-				char *lsm)
+			       struct lsm_id *lsmid)
 {
 	int i;
 
+	if (lsmid->slot == LSMBLOB_NEEDED) {
+		if (lsm_slot >= LSMBLOB_ENTRIES)
+			panic("%s Too many LSMs registered.\n", __func__);
+		lsm_slotlist[lsm_slot] = lsmid;
+		lsmid->slot = lsm_slot++;
+		init_debug("%s assigned lsmblob slot %d\n", lsmid->lsm,
+			   lsmid->slot);
+	}
+
 	for (i = 0; i < count; i++) {
-		hooks[i].lsm = lsm;
+		hooks[i].lsmid = lsmid;
 		hlist_add_tail_rcu(&hooks[i].list, hooks[i].head);
 	}
 
@@ -492,7 +546,7 @@
 	 * and fix this up afterwards.
 	 */
 	if (slab_is_available()) {
-		if (lsm_append(lsm, &lsm_names) < 0)
+		if (lsm_append(lsmid->lsm, &lsm_names) < 0)
 			panic("%s - Cannot get early memory.\n", __func__);
 	}
 }
@@ -606,6 +660,8 @@
  */
 static int lsm_task_alloc(struct task_struct *task)
 {
+	int *display;
+
 	if (blob_sizes.lbs_task == 0) {
 		task->security = NULL;
 		return 0;
@@ -614,6 +670,15 @@
 	task->security = kzalloc(blob_sizes.lbs_task, GFP_KERNEL);
 	if (task->security == NULL)
 		return -ENOMEM;
+
+	/*
+	 * The start of the task blob contains the "display" LSM slot number.
+	 * Start with it set to the invalid slot number, indicating that the
+	 * default first registered LSM be displayed.
+	 */
+	display = task->security;
+	*display = LSMBLOB_INVALID;
+
 	return 0;
 }
 
@@ -660,6 +725,28 @@
 }
 
 /**
+ * lsm_sock_alloc - allocate a composite sock blob
+ * @sock: the sock that needs a blob
+ * @priority: allocation mode
+ *
+ * Allocate the sock blob for all the modules
+ *
+ * Returns 0, or -ENOMEM if memory can't be allocated.
+ */
+static int lsm_sock_alloc(struct sock *sock, gfp_t priority)
+{
+	if (blob_sizes.lbs_sock == 0) {
+		sock->sk_security = NULL;
+		return 0;
+	}
+
+	sock->sk_security = kzalloc(blob_sizes.lbs_sock, priority);
+	if (sock->sk_security == NULL)
+		return -ENOMEM;
+	return 0;
+}
+
+/**
  * lsm_early_task - during initialization allocate a composite task blob
  * @task: the task that needs a blob
  *
@@ -674,6 +761,57 @@
 }
 
 /**
+ * append_ctx - append a lsm/context pair to a compound context
+ * @ctx: the existing compound context
+ * @ctxlen: size of the old context, including terminating nul byte
+ * @lsm: new lsm name, nul terminated
+ * @new: new context, possibly nul terminated
+ * @newlen: maximum size of @new
+ *
+ * replace @ctx with a new compound context, appending @newlsm and @new
+ * to @ctx. On exit the new data replaces the old, which is freed.
+ * @ctxlen is set to the new size, which includes a trailing nul byte.
+ *
+ * Returns 0 on success, -ENOMEM if no memory is available.
+ */
+static int append_ctx(char **ctx, int *ctxlen, const char *lsm, char *new,
+		      int newlen)
+{
+	char *final;
+	size_t llen;
+	size_t nlen;
+	size_t flen;
+
+	llen = strlen(lsm) + 1;
+	/*
+	 * A security module may or may not provide a trailing nul on
+	 * when returning a security context. There is no definition
+	 * of which it should be, and there are modules that do it
+	 * each way.
+	 */
+	nlen = strnlen(new, newlen);
+
+	flen = *ctxlen + llen + nlen + 1;
+	final = kzalloc(flen, GFP_KERNEL);
+
+	if (final == NULL)
+		return -ENOMEM;
+
+	if (*ctxlen)
+		memcpy(final, *ctx, *ctxlen);
+
+	memcpy(final + *ctxlen, lsm, llen);
+	memcpy(final + *ctxlen + llen, new, nlen);
+
+	kfree(*ctx);
+
+	*ctx = final;
+	*ctxlen = flen;
+
+	return 0;
+}
+
+/**
  * lsm_superblock_alloc - allocate a composite superblock blob
  * @sb: the superblock that needs a blob
  *
@@ -747,28 +885,61 @@
 
 /* Security operations */
 
-int security_binder_set_context_mgr(struct task_struct *mgr)
+int security_binder_set_context_mgr(const struct cred *mgr)
 {
 	return call_int_hook(binder_set_context_mgr, 0, mgr);
 }
+EXPORT_SYMBOL(security_binder_set_context_mgr);
 
-int security_binder_transaction(struct task_struct *from,
-				struct task_struct *to)
+/**
+ * security_binder_transaction - Binder driver transaction check
+ * @from: source of the transaction
+ * @to: destination of the transaction
+ *
+ * Verify that the creds have the same LSM "display", then
+ * call the security module hooks.
+ *
+ * Returns -EINVAL if the displays don't match, or the
+ * result of the security module checks.
+ */
+int security_binder_transaction(const struct cred *from,
+				const struct cred *to)
 {
+	int from_display = lsm_cred_display(from);
+	int to_display = lsm_cred_display(to);
+
+	/*
+	 * If the display is LSMBLOB_INVALID the first module that has
+	 * an entry is used. This will be in the 0 slot.
+	 *
+	 * This is currently only required if the server has requested
+	 * peer contexts, but it would be unwieldly to have too much of
+	 * the binder driver detail here.
+	 */
+	if (from_display == LSMBLOB_INVALID)
+		from_display = 0;
+	if (to_display == LSMBLOB_INVALID)
+		to_display = 0;
+	if (from_display != to_display)
+		return -EINVAL;
+
 	return call_int_hook(binder_transaction, 0, from, to);
 }
+EXPORT_SYMBOL(security_binder_transaction);
 
-int security_binder_transfer_binder(struct task_struct *from,
-				    struct task_struct *to)
+int security_binder_transfer_binder(const struct cred *from,
+				    const struct cred *to)
 {
 	return call_int_hook(binder_transfer_binder, 0, from, to);
 }
+EXPORT_SYMBOL(security_binder_transfer_binder);
 
-int security_binder_transfer_file(struct task_struct *from,
-				  struct task_struct *to, struct file *file)
+int security_binder_transfer_file(const struct cred *from,
+				  const struct cred *to, struct file *file)
 {
 	return call_int_hook(binder_transfer_file, 0, from, to, file);
 }
+EXPORT_SYMBOL(security_binder_transfer_file);
 
 int security_ptrace_access_check(struct task_struct *child, unsigned int mode)
 {
@@ -884,9 +1055,22 @@
 	return call_int_hook(fs_context_dup, 0, fc, src_fc);
 }
 
-int security_fs_context_parse_param(struct fs_context *fc, struct fs_parameter *param)
+int security_fs_context_parse_param(struct fs_context *fc,
+				    struct fs_parameter *param)
 {
-	return call_int_hook(fs_context_parse_param, -ENOPARAM, fc, param);
+	struct security_hook_list *hp;
+	int trc;
+	int rc = -ENOPARAM;
+
+	hlist_for_each_entry(hp, &security_hook_heads.fs_context_parse_param,
+			     list) {
+		trc = hp->hook.fs_context_parse_param(fc, param);
+		if (trc == 0)
+			rc = 0;
+		else if (trc != -ENOPARAM)
+			return trc;
+	}
+	return rc;
 }
 
 int security_sb_alloc(struct super_block *sb)
@@ -1147,6 +1331,7 @@
 		return 0;
 	return call_int_hook(path_rmdir, 0, dir, dentry);
 }
+EXPORT_SYMBOL_GPL(security_path_rmdir);
 
 int security_path_unlink(const struct path *dir, struct dentry *dentry)
 {
@@ -1163,6 +1348,7 @@
 		return 0;
 	return call_int_hook(path_symlink, 0, dir, dentry, old_name);
 }
+EXPORT_SYMBOL_GPL(security_path_symlink);
 
 int security_path_link(struct dentry *old_dentry, const struct path *new_dir,
 		       struct dentry *new_dentry)
@@ -1171,6 +1357,7 @@
 		return 0;
 	return call_int_hook(path_link, 0, old_dentry, new_dir, new_dentry);
 }
+EXPORT_SYMBOL_GPL(security_path_link);
 
 int security_path_rename(const struct path *old_dir, struct dentry *old_dentry,
 			 const struct path *new_dir, struct dentry *new_dentry,
@@ -1198,6 +1385,7 @@
 		return 0;
 	return call_int_hook(path_truncate, 0, path);
 }
+EXPORT_SYMBOL_GPL(security_path_truncate);
 
 int security_path_chmod(const struct path *path, umode_t mode)
 {
@@ -1205,6 +1393,7 @@
 		return 0;
 	return call_int_hook(path_chmod, 0, path, mode);
 }
+EXPORT_SYMBOL_GPL(security_path_chmod);
 
 int security_path_chown(const struct path *path, kuid_t uid, kgid_t gid)
 {
@@ -1212,6 +1401,7 @@
 		return 0;
 	return call_int_hook(path_chown, 0, path, uid, gid);
 }
+EXPORT_SYMBOL_GPL(security_path_chown);
 
 int security_path_chroot(const struct path *path)
 {
@@ -1312,6 +1502,7 @@
 		return 0;
 	return call_int_hook(inode_permission, 0, inode, mask);
 }
+EXPORT_SYMBOL_GPL(security_inode_permission);
 
 int security_inode_setattr(struct dentry *dentry, struct iattr *attr)
 {
@@ -1461,9 +1652,16 @@
 }
 EXPORT_SYMBOL(security_inode_listsecurity);
 
-void security_inode_getsecid(struct inode *inode, u32 *secid)
+void security_inode_getsecid(struct inode *inode, struct lsmblob *blob)
 {
-	call_void_hook(inode_getsecid, inode, secid);
+	struct security_hook_list *hp;
+
+	lsmblob_init(blob, 0);
+	hlist_for_each_entry(hp, &security_hook_heads.inode_getsecid, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		hp->hook.inode_getsecid(inode, &blob->secid[hp->lsmid->slot]);
+	}
 }
 
 int security_inode_copy_up(struct dentry *src, struct cred **new)
@@ -1509,6 +1707,7 @@
 
 	return fsnotify_perm(file, mask);
 }
+EXPORT_SYMBOL_GPL(security_file_permission);
 
 int security_file_alloc(struct file *file)
 {
@@ -1541,6 +1740,24 @@
 }
 EXPORT_SYMBOL_GPL(security_file_ioctl);
 
+/**
+ * security_file_ioctl_compat() - Check if an ioctl is allowed in compat mode
+ * @file: associated file
+ * @cmd: ioctl cmd
+ * @arg: ioctl arguments
+ *
+ * Compat version of security_file_ioctl() that correctly handles 32-bit
+ * processes running on 64-bit kernels.
+ *
+ * Return: Returns 0 if permission is granted.
+ */
+int security_file_ioctl_compat(struct file *file, unsigned int cmd,
+			       unsigned long arg)
+{
+	return call_int_hook(file_ioctl_compat, 0, file, cmd, arg);
+}
+EXPORT_SYMBOL_GPL(security_file_ioctl_compat);
+
 static inline unsigned long mmap_prot(struct file *file, unsigned long prot)
 {
 	/*
@@ -1577,12 +1794,13 @@
 int security_mmap_file(struct file *file, unsigned long prot,
 			unsigned long flags)
 {
+	unsigned long prot_adj = mmap_prot(file, prot);
 	int ret;
-	ret = call_int_hook(mmap_file, 0, file, prot,
-					mmap_prot(file, prot), flags);
+
+	ret = call_int_hook(mmap_file, 0, file, prot, prot_adj, flags);
 	if (ret)
 		return ret;
-	return ima_file_mmap(file, prot);
+	return ima_file_mmap(file, prot, prot_adj, flags);
 }
 
 int security_mmap_addr(unsigned long addr)
@@ -1640,14 +1858,26 @@
 
 int security_task_alloc(struct task_struct *task, unsigned long clone_flags)
 {
+	int *odisplay = current->security;
+	int *ndisplay;
 	int rc = lsm_task_alloc(task);
 
-	if (rc)
+	if (unlikely(rc))
 		return rc;
+
 	rc = call_int_hook(task_alloc, 0, task, clone_flags);
-	if (unlikely(rc))
+	if (unlikely(rc)) {
 		security_task_free(task);
-	return rc;
+		return rc;
+	}
+
+	if (odisplay) {
+		ndisplay = task->security;
+		if (ndisplay)
+			*ndisplay = *odisplay;
+	}
+
+	return 0;
 }
 
 void security_task_free(struct task_struct *task)
@@ -1704,16 +1934,32 @@
 	call_void_hook(cred_transfer, new, old);
 }
 
-void security_cred_getsecid(const struct cred *c, u32 *secid)
+void security_cred_getsecid(const struct cred *c, struct lsmblob *blob)
 {
-	*secid = 0;
-	call_void_hook(cred_getsecid, c, secid);
+	struct security_hook_list *hp;
+
+	lsmblob_init(blob, 0);
+	hlist_for_each_entry(hp, &security_hook_heads.cred_getsecid, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		hp->hook.cred_getsecid(c, &blob->secid[hp->lsmid->slot]);
+	}
 }
 EXPORT_SYMBOL(security_cred_getsecid);
 
-int security_kernel_act_as(struct cred *new, u32 secid)
+int security_kernel_act_as(struct cred *new, struct lsmblob *blob)
 {
-	return call_int_hook(kernel_act_as, 0, new, secid);
+	struct security_hook_list *hp;
+	int rc;
+
+	hlist_for_each_entry(hp, &security_hook_heads.kernel_act_as, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		rc = hp->hook.kernel_act_as(new, blob->secid[hp->lsmid->slot]);
+		if (rc != 0)
+			return rc;
+	}
+	return 0;
 }
 
 int security_kernel_create_files_as(struct cred *new, struct inode *inode)
@@ -1807,17 +2053,29 @@
 	return call_int_hook(task_getsid, 0, p);
 }
 
-void security_task_getsecid_subj(struct task_struct *p, u32 *secid)
+void security_task_getsecid_subj(struct task_struct *p, struct lsmblob *blob)
 {
-	*secid = 0;
-	call_void_hook(task_getsecid_subj, p, secid);
+	struct security_hook_list *hp;
+
+	lsmblob_init(blob, 0);
+	hlist_for_each_entry(hp, &security_hook_heads.task_getsecid_subj, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		hp->hook.task_getsecid_subj(p, &blob->secid[hp->lsmid->slot]);
+	}
 }
 EXPORT_SYMBOL(security_task_getsecid_subj);
 
-void security_task_getsecid_obj(struct task_struct *p, u32 *secid)
+void security_task_getsecid_obj(struct task_struct *p, struct lsmblob *blob)
 {
-	*secid = 0;
-	call_void_hook(task_getsecid_obj, p, secid);
+	struct security_hook_list *hp;
+
+	lsmblob_init(blob, 0);
+	hlist_for_each_entry(hp, &security_hook_heads.task_getsecid_obj, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		hp->hook.task_getsecid_obj(p, &blob->secid[hp->lsmid->slot]);
+	}
 }
 EXPORT_SYMBOL(security_task_getsecid_obj);
 
@@ -1897,10 +2155,16 @@
 	return call_int_hook(ipc_permission, 0, ipcp, flag);
 }
 
-void security_ipc_getsecid(struct kern_ipc_perm *ipcp, u32 *secid)
+void security_ipc_getsecid(struct kern_ipc_perm *ipcp, struct lsmblob *blob)
 {
-	*secid = 0;
-	call_void_hook(ipc_getsecid, ipcp, secid);
+	struct security_hook_list *hp;
+
+	lsmblob_init(blob, 0);
+	hlist_for_each_entry(hp, &security_hook_heads.ipc_getsecid, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		hp->hook.ipc_getsecid(ipcp, &blob->secid[hp->lsmid->slot]);
+	}
 }
 
 int security_msg_msg_alloc(struct msg_msg *msg)
@@ -2044,22 +2308,137 @@
 				char **value)
 {
 	struct security_hook_list *hp;
+	char *final = NULL;
+	char *cp;
+	int rc = 0;
+	int finallen = 0;
+	int display = lsm_task_display(current);
+	int slot = 0;
+
+	if (!strcmp(name, "display")) {
+		/*
+		 * lsm_slot will be 0 if there are no displaying modules.
+		 */
+		if (lsm_slot == 0)
+			return -EINVAL;
+
+		/*
+		 * Only allow getting the current process' display.
+		 * There are too few reasons to get another process'
+		 * display and too many LSM policy issues.
+		 */
+		if (current != p)
+			return -EINVAL;
+
+		display = lsm_task_display(p);
+		if (display != LSMBLOB_INVALID)
+			slot = display;
+		*value = kstrdup(lsm_slotlist[slot]->lsm, GFP_KERNEL);
+		if (*value)
+			return strlen(*value);
+		return -ENOMEM;
+	}
+
+	if (!strcmp(name, "context")) {
+		hlist_for_each_entry(hp, &security_hook_heads.getprocattr,
+				     list) {
+			rc = hp->hook.getprocattr(p, "context", &cp);
+			if (rc == -EINVAL)
+				continue;
+			if (rc < 0) {
+				kfree(final);
+				return rc;
+			}
+			rc = append_ctx(&final, &finallen, hp->lsmid->lsm,
+					cp, rc);
+			kfree(cp);
+			if (rc < 0) {
+				kfree(final);
+				return rc;
+			}
+		}
+		if (final == NULL)
+			return -EINVAL;
+		*value = final;
+		return finallen;
+	}
 
 	hlist_for_each_entry(hp, &security_hook_heads.getprocattr, list) {
-		if (lsm != NULL && strcmp(lsm, hp->lsm))
+		if (lsm != NULL && strcmp(lsm, hp->lsmid->lsm))
+			continue;
+		if (lsm == NULL && display != LSMBLOB_INVALID &&
+		    display != hp->lsmid->slot)
 			continue;
 		return hp->hook.getprocattr(p, name, value);
 	}
 	return LSM_RET_DEFAULT(getprocattr);
 }
 
+/**
+ * security_setprocattr - Set process attributes via /proc
+ * @lsm: name of module involved, or NULL
+ * @name: name of the attribute
+ * @value: value to set the attribute to
+ * @size: size of the value
+ *
+ * Set the process attribute for the specified security module
+ * to the specified value. Note that this can only be used to set
+ * the process attributes for the current, or "self" process.
+ * The /proc code has already done this check.
+ *
+ * Returns 0 on success, an appropriate code otherwise.
+ */
 int security_setprocattr(const char *lsm, const char *name, void *value,
 			 size_t size)
 {
 	struct security_hook_list *hp;
+	char *termed;
+	char *copy;
+	int *display = current->security;
+	int rc = -EINVAL;
+	int slot = 0;
+
+	if (!strcmp(name, "display")) {
+		/*
+		 * Change the "display" value only if all the security
+		 * modules that support setting a procattr allow it.
+		 * It is assumed that all such security modules will be
+		 * cooperative.
+		 */
+		if (size == 0)
+			return -EINVAL;
+
+		hlist_for_each_entry(hp, &security_hook_heads.setprocattr,
+				     list) {
+			rc = hp->hook.setprocattr(name, value, size);
+			if (rc < 0 && rc != -EINVAL)
+				return rc;
+		}
+
+		rc = -EINVAL;
+
+		copy = kmemdup_nul(value, size, GFP_KERNEL);
+		if (copy == NULL)
+			return -ENOMEM;
+
+		termed = strsep(&copy, " \n");
+
+		for (slot = 0; slot < lsm_slot; slot++)
+			if (!strcmp(termed, lsm_slotlist[slot]->lsm)) {
+				*display = lsm_slotlist[slot]->slot;
+				rc = size;
+				break;
+			}
+
+		kfree(termed);
+		return rc;
+	}
 
 	hlist_for_each_entry(hp, &security_hook_heads.setprocattr, list) {
-		if (lsm != NULL && strcmp(lsm, hp->lsm))
+		if (lsm != NULL && strcmp(lsm, hp->lsmid->lsm))
+			continue;
+		if (lsm == NULL && *display != LSMBLOB_INVALID &&
+		    *display != hp->lsmid->slot)
 			continue;
 		return hp->hook.setprocattr(name, value, size);
 	}
@@ -2077,35 +2456,76 @@
 }
 EXPORT_SYMBOL(security_ismaclabel);
 
-int security_secid_to_secctx(u32 secid, char **secdata, u32 *seclen)
+int security_secid_to_secctx(struct lsmblob *blob, struct lsmcontext *cp,
+			     int display)
 {
 	struct security_hook_list *hp;
-	int rc;
+
+	memset(cp, 0, sizeof(*cp));
 
 	/*
-	 * Currently, only one LSM can implement secid_to_secctx (i.e this
-	 * LSM hook is not "stackable").
+	 * display either is the slot number use for formatting
+	 * or an instruction on which relative slot to use.
 	 */
+	if (display == LSMBLOB_DISPLAY)
+		display = lsm_task_display(current);
+	else if (display == LSMBLOB_FIRST)
+		display = LSMBLOB_INVALID;
+	else if (display < 0) {
+		WARN_ONCE(true,
+			"LSM: %s unknown display\n", __func__);
+		display = LSMBLOB_INVALID;
+	} else if (display >= lsm_slot) {
+		WARN_ONCE(true,
+			"LSM: %s invalid display\n", __func__);
+		display = LSMBLOB_INVALID;
+	}
+
+
 	hlist_for_each_entry(hp, &security_hook_heads.secid_to_secctx, list) {
-		rc = hp->hook.secid_to_secctx(secid, secdata, seclen);
-		if (rc != LSM_RET_DEFAULT(secid_to_secctx))
-			return rc;
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		if (display == LSMBLOB_INVALID || display == hp->lsmid->slot) {
+			cp->slot = hp->lsmid->slot;
+			return hp->hook.secid_to_secctx(
+					blob->secid[hp->lsmid->slot],
+					&cp->context, &cp->len);
+		}
 	}
 
 	return LSM_RET_DEFAULT(secid_to_secctx);
 }
 EXPORT_SYMBOL(security_secid_to_secctx);
 
-int security_secctx_to_secid(const char *secdata, u32 seclen, u32 *secid)
+int security_secctx_to_secid(const char *secdata, u32 seclen,
+			     struct lsmblob *blob)
 {
-	*secid = 0;
-	return call_int_hook(secctx_to_secid, 0, secdata, seclen, secid);
+	struct security_hook_list *hp;
+	int display = lsm_task_display(current);
+
+	lsmblob_init(blob, 0);
+	hlist_for_each_entry(hp, &security_hook_heads.secctx_to_secid, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		if (display == LSMBLOB_INVALID || display == hp->lsmid->slot)
+			return hp->hook.secctx_to_secid(secdata, seclen,
+						&blob->secid[hp->lsmid->slot]);
+	}
+	return -EOPNOTSUPP;
 }
 EXPORT_SYMBOL(security_secctx_to_secid);
 
-void security_release_secctx(char *secdata, u32 seclen)
+void security_release_secctx(struct lsmcontext *cp)
 {
-	call_void_hook(release_secctx, secdata, seclen);
+	struct security_hook_list *hp;
+
+	hlist_for_each_entry(hp, &security_hook_heads.release_secctx, list)
+		if (cp->slot == hp->lsmid->slot) {
+			hp->hook.release_secctx(cp->context, cp->len);
+			break;
+		}
+
+	memset(cp, 0, sizeof(*cp));
 }
 EXPORT_SYMBOL(security_release_secctx);
 
@@ -2127,9 +2547,18 @@
 }
 EXPORT_SYMBOL(security_inode_setsecctx);
 
-int security_inode_getsecctx(struct inode *inode, void **ctx, u32 *ctxlen)
+int security_inode_getsecctx(struct inode *inode, struct lsmcontext *cp)
 {
-	return call_int_hook(inode_getsecctx, -EOPNOTSUPP, inode, ctx, ctxlen);
+	struct security_hook_list *hp;
+
+	memset(cp, 0, sizeof(*cp));
+
+	hlist_for_each_entry(hp, &security_hook_heads.inode_getsecctx, list) {
+		cp->slot = hp->lsmid->slot;
+		return hp->hook.inode_getsecctx(inode, (void **)&cp->context,
+						&cp->len);
+	}
+	return -EOPNOTSUPP;
 }
 EXPORT_SYMBOL(security_inode_getsecctx);
 
@@ -2246,25 +2675,53 @@
 int security_socket_getpeersec_stream(struct socket *sock, char __user *optval,
 				      int __user *optlen, unsigned len)
 {
-	return call_int_hook(socket_getpeersec_stream, -ENOPROTOOPT, sock,
-				optval, optlen, len);
+	int display = lsm_task_display(current);
+	struct security_hook_list *hp;
+
+	hlist_for_each_entry(hp, &security_hook_heads.socket_getpeersec_stream,
+			     list)
+		if (display == LSMBLOB_INVALID || display == hp->lsmid->slot)
+			return hp->hook.socket_getpeersec_stream(sock, optval,
+								 optlen, len);
+	return -ENOPROTOOPT;
 }
 
-int security_socket_getpeersec_dgram(struct socket *sock, struct sk_buff *skb, u32 *secid)
+int security_socket_getpeersec_dgram(struct socket *sock, struct sk_buff *skb,
+				     struct lsmblob *blob)
 {
-	return call_int_hook(socket_getpeersec_dgram, -ENOPROTOOPT, sock,
-			     skb, secid);
+	struct security_hook_list *hp;
+	int rc = -ENOPROTOOPT;
+
+	hlist_for_each_entry(hp, &security_hook_heads.socket_getpeersec_dgram,
+			     list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		rc = hp->hook.socket_getpeersec_dgram(sock, skb,
+						&blob->secid[hp->lsmid->slot]);
+		if (rc != 0)
+			break;
+	}
+	return rc;
 }
 EXPORT_SYMBOL(security_socket_getpeersec_dgram);
 
 int security_sk_alloc(struct sock *sk, int family, gfp_t priority)
 {
-	return call_int_hook(sk_alloc_security, 0, sk, family, priority);
+	int rc = lsm_sock_alloc(sk, priority);
+
+	if (unlikely(rc))
+		return rc;
+	rc = call_int_hook(sk_alloc_security, 0, sk, family, priority);
+	if (unlikely(rc))
+		security_sk_free(sk);
+	return rc;
 }
 
 void security_sk_free(struct sock *sk)
 {
 	call_void_hook(sk_free_security, sk);
+	kfree(sk->sk_security);
+	sk->sk_security = NULL;
 }
 
 void security_sk_clone(const struct sock *sk, struct sock *newsk)
@@ -2312,9 +2769,21 @@
 }
 EXPORT_SYMBOL(security_inet_conn_established);
 
-int security_secmark_relabel_packet(u32 secid)
+int security_secmark_relabel_packet(struct lsmblob *blob)
 {
-	return call_int_hook(secmark_relabel_packet, 0, secid);
+	struct security_hook_list *hp;
+	int rc = 0;
+
+	hlist_for_each_entry(hp, &security_hook_heads.secmark_relabel_packet,
+			     list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		rc = hp->hook.secmark_relabel_packet(
+						blob->secid[hp->lsmid->slot]);
+		if (rc != 0)
+			break;
+	}
+	return rc;
 }
 EXPORT_SYMBOL(security_secmark_relabel_packet);
 
@@ -2541,9 +3010,22 @@
 
 #ifdef CONFIG_AUDIT
 
-int security_audit_rule_init(u32 field, u32 op, char *rulestr, void **lsmrule)
+int security_audit_rule_init(u32 field, u32 op, char *rulestr, void **lsmrule,
+			     gfp_t gfp)
 {
-	return call_int_hook(audit_rule_init, 0, field, op, rulestr, lsmrule);
+	struct security_hook_list *hp;
+	int display = lsm_task_display(current);
+
+	hlist_for_each_entry(hp, &security_hook_heads.audit_rule_init, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		if (display != LSMBLOB_INVALID && display != hp->lsmid->slot)
+			continue;
+		return hp->hook.audit_rule_init(field, op, rulestr,
+						&lsmrule[hp->lsmid->slot],
+						gfp);
+	}
+	return 0;
 }
 
 int security_audit_rule_known(struct audit_krule *krule)
@@ -2551,14 +3033,39 @@
 	return call_int_hook(audit_rule_known, 0, krule);
 }
 
-void security_audit_rule_free(void *lsmrule)
+void security_audit_rule_free(void **lsmrule)
 {
-	call_void_hook(audit_rule_free, lsmrule);
+	struct security_hook_list *hp;
+
+	hlist_for_each_entry(hp, &security_hook_heads.audit_rule_free, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		if (lsmrule[hp->lsmid->slot] == NULL)
+			continue;
+		hp->hook.audit_rule_free(lsmrule[hp->lsmid->slot]);
+	}
 }
 
-int security_audit_rule_match(u32 secid, u32 field, u32 op, void *lsmrule)
+int security_audit_rule_match(struct lsmblob *blob, u32 field, u32 op,
+			      void **lsmrule)
 {
-	return call_int_hook(audit_rule_match, 0, secid, field, op, lsmrule);
+	struct security_hook_list *hp;
+	int rc;
+
+	hlist_for_each_entry(hp, &security_hook_heads.audit_rule_match, list) {
+		if (WARN_ON(hp->lsmid->slot < 0 || hp->lsmid->slot >= lsm_slot))
+			continue;
+		if (lsmrule[hp->lsmid->slot] == NULL)
+			continue;
+		if (lsmrule[hp->lsmid->slot] == NULL)
+			continue;
+		rc = hp->hook.audit_rule_match(blob->secid[hp->lsmid->slot],
+					       field, op,
+					       &lsmrule[hp->lsmid->slot]);
+		if (rc)
+			return rc;
+	}
+	return 0;
 }
 #endif /* CONFIG_AUDIT */
 
@@ -2599,6 +3106,12 @@
 }
 EXPORT_SYMBOL(security_locked_down);
 
+int security_lock_kernel_down(const char *where, enum lockdown_reason level)
+{
+	return call_int_hook(lock_kernel_down, 0, where, level);
+}
+EXPORT_SYMBOL(security_lock_kernel_down);
+
 #ifdef CONFIG_PERF_EVENTS
 int security_perf_event_open(struct perf_event_attr *attr, int type)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/Makefile
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/Makefile
@@ -23,8 +23,12 @@
 $(addprefix $(obj)/,$(selinux-y)): $(obj)/flask.h
 
 quiet_cmd_flask = GEN     $(obj)/flask.h $(obj)/av_permissions.h
-      cmd_flask = scripts/selinux/genheaders/genheaders $(obj)/flask.h $(obj)/av_permissions.h
+      cmd_flask = $< $(obj)/flask.h $(obj)/av_permissions.h
 
 targets += flask.h av_permissions.h
-$(obj)/flask.h: $(src)/include/classmap.h FORCE
+# once make >= 4.3 is required, we can use grouped targets in the rule below,
+# which basically involves adding both headers and a '&' before the colon, see
+# the example below:
+#   $(obj)/flask.h $(obj)/av_permissions.h &: scripts/selinux/...
+$(obj)/flask.h: scripts/selinux/genheaders/genheaders FORCE
 	$(call if_changed,flask)
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/avc.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/avc.c
@@ -332,12 +332,12 @@
 {
 	struct avc_xperms_decision_node *dest_xpd;
 
-	node->ae.xp_node->xp.len++;
 	dest_xpd = avc_xperms_decision_alloc(src->used);
 	if (!dest_xpd)
 		return -ENOMEM;
 	avc_copy_xperms_decision(&dest_xpd->xpd, src);
 	list_add(&dest_xpd->xpd_list, &node->ae.xp_node->xpd_head);
+	node->ae.xp_node->xp.len++;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/hooks.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/hooks.c
@@ -255,29 +255,6 @@
 	return sid;
 }
 
-/*
- * get the security ID of a task for use with binder
- */
-static inline u32 task_sid_binder(const struct task_struct *task)
-{
-	/*
-	 * In many case where this function is used we should be using the
-	 * task's subjective SID, but we can't reliably access the subjective
-	 * creds of a task other than our own so we must use the objective
-	 * creds/SID, which are safe to access.  The downside is that if a task
-	 * is temporarily overriding it's creds it will not be reflected here;
-	 * however, it isn't clear that binder would handle that case well
-	 * anyway.
-	 *
-	 * If this ever changes and we can safely reference the subjective
-	 * creds/SID of another task, this function will make it easier to
-	 * identify the various places where we make use of the task SIDs in
-	 * the binder code.  It is also likely that we will need to adjust
-	 * the main drivers/android binder code as well.
-	 */
-	return task_sid_obj(task);
-}
-
 static int inode_doinit_with_dentry(struct inode *inode, struct dentry *opt_dentry);
 
 /*
@@ -378,6 +355,10 @@
 
 struct selinux_mnt_opts {
 	const char *fscontext, *context, *rootcontext, *defcontext;
+	u32 fscontext_sid;
+	u32 context_sid;
+	u32 rootcontext_sid;
+	u32 defcontext_sid;
 };
 
 static void selinux_free_mnt_opts(void *mnt_opts)
@@ -515,7 +496,7 @@
 
 static int sb_check_xattr_support(struct super_block *sb)
 {
-	struct superblock_security_struct *sbsec = sb->s_security;
+	struct superblock_security_struct *sbsec = selinux_superblock(sb);
 	struct dentry *root = sb->s_root;
 	struct inode *root_inode = d_backing_inode(root);
 	u32 sid;
@@ -641,7 +622,7 @@
 	if (rc)
 		pr_warn("SELinux: security_context_str_to_sid"
 		       "(%s) failed for (dev %s, type %s) errno=%d\n",
-		       s, sb->s_id, sb->s_type->name, rc);
+		       s, sb ? sb->s_id : "?", sb ? sb->s_type->name : "?", rc);
 	return rc;
 }
 
@@ -1005,42 +986,58 @@
 static int selinux_add_opt(int token, const char *s, void **mnt_opts)
 {
 	struct selinux_mnt_opts *opts = *mnt_opts;
+	bool is_alloc_opts = false;
 
 	if (token == Opt_seclabel)	/* eaten and completely ignored */
 		return 0;
 
+	if (!s)
+		return -ENOMEM;
+
 	if (!opts) {
 		opts = kzalloc(sizeof(struct selinux_mnt_opts), GFP_KERNEL);
 		if (!opts)
 			return -ENOMEM;
 		*mnt_opts = opts;
+		is_alloc_opts = true;
 	}
-	if (!s)
-		return -ENOMEM;
+
 	switch (token) {
 	case Opt_context:
 		if (opts->context || opts->defcontext)
 			goto Einval;
 		opts->context = s;
+		if (selinux_initialized(&selinux_state))
+			parse_sid(NULL, s, &opts->context_sid);
 		break;
 	case Opt_fscontext:
 		if (opts->fscontext)
 			goto Einval;
 		opts->fscontext = s;
+		if (selinux_initialized(&selinux_state))
+			parse_sid(NULL, s, &opts->fscontext_sid);
 		break;
 	case Opt_rootcontext:
 		if (opts->rootcontext)
 			goto Einval;
 		opts->rootcontext = s;
+		if (selinux_initialized(&selinux_state))
+			parse_sid(NULL, s, &opts->rootcontext_sid);
 		break;
 	case Opt_defcontext:
 		if (opts->context || opts->defcontext)
 			goto Einval;
 		opts->defcontext = s;
+		if (selinux_initialized(&selinux_state))
+			parse_sid(NULL, s, &opts->defcontext_sid);
 		break;
 	}
 	return 0;
 Einval:
+	if (is_alloc_opts) {
+		kfree(opts);
+		*mnt_opts = NULL;
+	}
 	pr_warn(SEL_MOUNT_FAIL_MSG);
 	return -EINVAL;
 }
@@ -2066,18 +2063,19 @@
 
 /* Hook functions begin here. */
 
-static int selinux_binder_set_context_mgr(struct task_struct *mgr)
+static int selinux_binder_set_context_mgr(const struct cred *mgr)
 {
 	return avc_has_perm(&selinux_state,
-			    current_sid(), task_sid_binder(mgr), SECCLASS_BINDER,
+			    current_sid(), cred_sid(mgr), SECCLASS_BINDER,
 			    BINDER__SET_CONTEXT_MGR, NULL);
 }
 
-static int selinux_binder_transaction(struct task_struct *from,
-				      struct task_struct *to)
+static int selinux_binder_transaction(const struct cred *from,
+				      const struct cred *to)
 {
 	u32 mysid = current_sid();
-	u32 fromsid = task_sid_binder(from);
+	u32 fromsid = cred_sid(from);
+	u32 tosid = cred_sid(to);
 	int rc;
 
 	if (mysid != fromsid) {
@@ -2088,24 +2086,24 @@
 			return rc;
 	}
 
-	return avc_has_perm(&selinux_state, fromsid, task_sid_binder(to),
+	return avc_has_perm(&selinux_state, fromsid, tosid,
 			    SECCLASS_BINDER, BINDER__CALL, NULL);
 }
 
-static int selinux_binder_transfer_binder(struct task_struct *from,
-					  struct task_struct *to)
+static int selinux_binder_transfer_binder(const struct cred *from,
+					  const struct cred *to)
 {
 	return avc_has_perm(&selinux_state,
-			    task_sid_binder(from), task_sid_binder(to),
+			    cred_sid(from), cred_sid(to),
 			    SECCLASS_BINDER, BINDER__TRANSFER,
 			    NULL);
 }
 
-static int selinux_binder_transfer_file(struct task_struct *from,
-					struct task_struct *to,
+static int selinux_binder_transfer_file(const struct cred *from,
+					const struct cred *to,
 					struct file *file)
 {
-	u32 sid = task_sid_binder(to);
+	u32 sid = cred_sid(to);
 	struct file_security_struct *fsec = selinux_file(file);
 	struct dentry *dentry = file->f_path.dentry;
 	struct inode_security_struct *isec;
@@ -2704,9 +2702,7 @@
 static int selinux_sb_mnt_opts_compat(struct super_block *sb, void *mnt_opts)
 {
 	struct selinux_mnt_opts *opts = mnt_opts;
-	struct superblock_security_struct *sbsec = sb->s_security;
-	u32 sid;
-	int rc;
+	struct superblock_security_struct *sbsec = selinux_superblock(sb);
 
 	/*
 	 * Superblock not initialized (i.e. no options) - reject if any
@@ -2723,34 +2719,36 @@
 		return (sbsec->flags & SE_MNTMASK) ? 1 : 0;
 
 	if (opts->fscontext) {
-		rc = parse_sid(sb, opts->fscontext, &sid);
-		if (rc)
+		if (opts->fscontext_sid == SECSID_NULL)
 			return 1;
-		if (bad_option(sbsec, FSCONTEXT_MNT, sbsec->sid, sid))
+		else if (bad_option(sbsec, FSCONTEXT_MNT, sbsec->sid,
+				       opts->fscontext_sid))
 			return 1;
 	}
 	if (opts->context) {
-		rc = parse_sid(sb, opts->context, &sid);
-		if (rc)
+		if (opts->context_sid == SECSID_NULL)
 			return 1;
-		if (bad_option(sbsec, CONTEXT_MNT, sbsec->mntpoint_sid, sid))
+		else if (bad_option(sbsec, CONTEXT_MNT, sbsec->mntpoint_sid,
+				       opts->context_sid))
 			return 1;
 	}
 	if (opts->rootcontext) {
-		struct inode_security_struct *root_isec;
-
-		root_isec = backing_inode_security(sb->s_root);
-		rc = parse_sid(sb, opts->rootcontext, &sid);
-		if (rc)
-			return 1;
-		if (bad_option(sbsec, ROOTCONTEXT_MNT, root_isec->sid, sid))
+		if (opts->rootcontext_sid == SECSID_NULL)
 			return 1;
+		else {
+			struct inode_security_struct *root_isec;
+
+			root_isec = backing_inode_security(sb->s_root);
+			if (bad_option(sbsec, ROOTCONTEXT_MNT, root_isec->sid,
+				       opts->rootcontext_sid))
+				return 1;
+		}
 	}
 	if (opts->defcontext) {
-		rc = parse_sid(sb, opts->defcontext, &sid);
-		if (rc)
+		if (opts->defcontext_sid == SECSID_NULL)
 			return 1;
-		if (bad_option(sbsec, DEFCONTEXT_MNT, sbsec->def_sid, sid))
+		else if (bad_option(sbsec, DEFCONTEXT_MNT, sbsec->def_sid,
+				       opts->defcontext_sid))
 			return 1;
 	}
 	return 0;
@@ -2917,10 +2915,9 @@
 		return opt;
 
 	rc = selinux_add_opt(opt, param->string, &fc->security);
-	if (!rc) {
+	if (!rc)
 		param->string = NULL;
-		rc = 1;
-	}
+
 	return rc;
 }
 
@@ -3798,6 +3795,12 @@
 					    CAP_OPT_NONE, true);
 		break;
 
+	case FIOCLEX:
+	case FIONCLEX:
+		if (!selinux_policycap_ioctl_skip_cloexec())
+			error = ioctl_has_perm(cred, file, FILE__IOCTL, (u16) cmd);
+		break;
+
 	/* default case assumes that the command will go
 	 * to the file's ioctl() function.
 	 */
@@ -3807,6 +3810,33 @@
 	return error;
 }
 
+static int selinux_file_ioctl_compat(struct file *file, unsigned int cmd,
+			      unsigned long arg)
+{
+	/*
+	 * If we are in a 64-bit kernel running 32-bit userspace, we need to
+	 * make sure we don't compare 32-bit flags to 64-bit flags.
+	 */
+	switch (cmd) {
+	case FS_IOC32_GETFLAGS:
+		cmd = FS_IOC_GETFLAGS;
+		break;
+	case FS_IOC32_SETFLAGS:
+		cmd = FS_IOC_SETFLAGS;
+		break;
+	case FS_IOC32_GETVERSION:
+		cmd = FS_IOC_GETVERSION;
+		break;
+	case FS_IOC32_SETVERSION:
+		cmd = FS_IOC_SETVERSION;
+		break;
+	default:
+		break;
+	}
+
+	return selinux_file_ioctl(file, cmd, arg);
+}
+
 static int default_noexec __ro_after_init;
 
 static int file_map_prot_check(struct file *file, unsigned long prot, int shared)
@@ -4646,7 +4676,7 @@
 
 static int sock_has_perm(struct sock *sk, u32 perms)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	struct common_audit_data ad;
 	struct lsm_network_audit net = {0,};
 
@@ -4703,7 +4733,7 @@
 	isec->initialized = LABEL_INITIALIZED;
 
 	if (sock->sk) {
-		sksec = sock->sk->sk_security;
+		sksec = selinux_sock(sock->sk);
 		sksec->sclass = sclass;
 		sksec->sid = sid;
 		/* Allows detection of the first association on this socket */
@@ -4719,8 +4749,8 @@
 static int selinux_socket_socketpair(struct socket *socka,
 				     struct socket *sockb)
 {
-	struct sk_security_struct *sksec_a = socka->sk->sk_security;
-	struct sk_security_struct *sksec_b = sockb->sk->sk_security;
+	struct sk_security_struct *sksec_a = selinux_sock(socka->sk);
+	struct sk_security_struct *sksec_b = selinux_sock(sockb->sk);
 
 	sksec_a->peer_sid = sksec_b->sid;
 	sksec_b->peer_sid = sksec_a->sid;
@@ -4735,7 +4765,7 @@
 static int selinux_socket_bind(struct socket *sock, struct sockaddr *address, int addrlen)
 {
 	struct sock *sk = sock->sk;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	u16 family;
 	int err;
 
@@ -4771,6 +4801,13 @@
 				return -EINVAL;
 			addr4 = (struct sockaddr_in *)address;
 			if (family_sa == AF_UNSPEC) {
+				if (family == PF_INET6) {
+					/* Length check from inet6_bind_sk() */
+					if (addrlen < SIN6_LEN_RFC2133)
+						return -EINVAL;
+					/* Family check from __inet6_bind() */
+					goto err_af;
+				}
 				/* see __inet_bind(), we only want to allow
 				 * AF_UNSPEC if the address is INADDR_ANY
 				 */
@@ -4870,7 +4907,7 @@
 					 struct sockaddr *address, int addrlen)
 {
 	struct sock *sk = sock->sk;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	int err;
 
 	err = sock_has_perm(sk, SOCKET__CONNECT);
@@ -5049,9 +5086,9 @@
 					      struct sock *other,
 					      struct sock *newsk)
 {
-	struct sk_security_struct *sksec_sock = sock->sk_security;
-	struct sk_security_struct *sksec_other = other->sk_security;
-	struct sk_security_struct *sksec_new = newsk->sk_security;
+	struct sk_security_struct *sksec_sock = selinux_sock(sock);
+	struct sk_security_struct *sksec_other = selinux_sock(other);
+	struct sk_security_struct *sksec_new = selinux_sock(newsk);
 	struct common_audit_data ad;
 	struct lsm_network_audit net = {0,};
 	int err;
@@ -5083,8 +5120,8 @@
 static int selinux_socket_unix_may_send(struct socket *sock,
 					struct socket *other)
 {
-	struct sk_security_struct *ssec = sock->sk->sk_security;
-	struct sk_security_struct *osec = other->sk->sk_security;
+	struct sk_security_struct *ssec = selinux_sock(sock->sk);
+	struct sk_security_struct *osec = selinux_sock(other->sk);
 	struct common_audit_data ad;
 	struct lsm_network_audit net = {0,};
 
@@ -5126,7 +5163,7 @@
 				       u16 family)
 {
 	int err = 0;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	u32 sk_sid = sksec->sid;
 	struct common_audit_data ad;
 	struct lsm_network_audit net = {0,};
@@ -5159,7 +5196,7 @@
 static int selinux_socket_sock_rcv_skb(struct sock *sk, struct sk_buff *skb)
 {
 	int err;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	u16 family = sk->sk_family;
 	u32 sk_sid = sksec->sid;
 	struct common_audit_data ad;
@@ -5227,13 +5264,15 @@
 	return err;
 }
 
-static int selinux_socket_getpeersec_stream(struct socket *sock, char __user *optval,
-					    int __user *optlen, unsigned len)
+static int selinux_socket_getpeersec_stream(struct socket *sock,
+					    char __user *optval,
+					    int __user *optlen,
+					    unsigned int len)
 {
 	int err = 0;
 	char *scontext;
 	u32 scontext_len;
-	struct sk_security_struct *sksec = sock->sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sock->sk);
 	u32 peer_sid = SECSID_NULL;
 
 	if (sksec->sclass == SECCLASS_UNIX_STREAM_SOCKET ||
@@ -5293,34 +5332,27 @@
 
 static int selinux_sk_alloc_security(struct sock *sk, int family, gfp_t priority)
 {
-	struct sk_security_struct *sksec;
-
-	sksec = kzalloc(sizeof(*sksec), priority);
-	if (!sksec)
-		return -ENOMEM;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
 	sksec->peer_sid = SECINITSID_UNLABELED;
 	sksec->sid = SECINITSID_UNLABELED;
 	sksec->sclass = SECCLASS_SOCKET;
 	selinux_netlbl_sk_security_reset(sksec);
-	sk->sk_security = sksec;
 
 	return 0;
 }
 
 static void selinux_sk_free_security(struct sock *sk)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
-	sk->sk_security = NULL;
 	selinux_netlbl_sk_security_free(sksec);
-	kfree(sksec);
 }
 
 static void selinux_sk_clone_security(const struct sock *sk, struct sock *newsk)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
-	struct sk_security_struct *newsksec = newsk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
+	struct sk_security_struct *newsksec = selinux_sock(newsk);
 
 	newsksec->sid = sksec->sid;
 	newsksec->peer_sid = sksec->peer_sid;
@@ -5334,7 +5366,7 @@
 	if (!sk)
 		*secid = SECINITSID_ANY_SOCKET;
 	else {
-		struct sk_security_struct *sksec = sk->sk_security;
+		struct sk_security_struct *sksec = selinux_sock(sk);
 
 		*secid = sksec->sid;
 	}
@@ -5344,7 +5376,7 @@
 {
 	struct inode_security_struct *isec =
 		inode_security_novalidate(SOCK_INODE(parent));
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
 	if (sk->sk_family == PF_INET || sk->sk_family == PF_INET6 ||
 	    sk->sk_family == PF_UNIX)
@@ -5359,7 +5391,7 @@
 static int selinux_sctp_assoc_request(struct sctp_endpoint *ep,
 				      struct sk_buff *skb)
 {
-	struct sk_security_struct *sksec = ep->base.sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(ep->base.sk);
 	struct common_audit_data ad;
 	struct lsm_network_audit net = {0,};
 	u8 peerlbl_active;
@@ -5510,8 +5542,8 @@
 static void selinux_sctp_sk_clone(struct sctp_endpoint *ep, struct sock *sk,
 				  struct sock *newsk)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
-	struct sk_security_struct *newsksec = newsk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
+	struct sk_security_struct *newsksec = selinux_sock(newsk);
 
 	/* If policy does not support SECCLASS_SCTP_SOCKET then call
 	 * the non-sctp clone version.
@@ -5528,7 +5560,7 @@
 static int selinux_inet_conn_request(const struct sock *sk, struct sk_buff *skb,
 				     struct request_sock *req)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	int err;
 	u16 family = req->rsk_ops->family;
 	u32 connsid;
@@ -5549,7 +5581,7 @@
 static void selinux_inet_csk_clone(struct sock *newsk,
 				   const struct request_sock *req)
 {
-	struct sk_security_struct *newsksec = newsk->sk_security;
+	struct sk_security_struct *newsksec = selinux_sock(newsk);
 
 	newsksec->sid = req->secid;
 	newsksec->peer_sid = req->peer_secid;
@@ -5566,7 +5598,7 @@
 static void selinux_inet_conn_established(struct sock *sk, struct sk_buff *skb)
 {
 	u16 family = sk->sk_family;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
 	/* handle mapped IPv4 packets arriving via IPv6 sockets */
 	if (family == PF_INET6 && skb->protocol == htons(ETH_P_IP))
@@ -5650,7 +5682,7 @@
 static int selinux_tun_dev_attach(struct sock *sk, void *security)
 {
 	struct tun_security_struct *tunsec = security;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
 	/* we don't currently perform any NetLabel based labeling here and it
 	 * isn't clear that we would want to do so anyway; while we could apply
@@ -5794,7 +5826,7 @@
 			return NF_ACCEPT;
 
 		/* standard practice, label using the parent socket */
-		sksec = sk->sk_security;
+		sksec = selinux_sock(sk);
 		sid = sksec->sid;
 	} else
 		sid = SECINITSID_KERNEL;
@@ -5829,11 +5861,11 @@
 	struct common_audit_data ad;
 	struct lsm_network_audit net = {0,};
 	char *addrp;
-	u8 proto;
+	u8 proto = 0;
 
 	if (sk == NULL)
 		return NF_ACCEPT;
-	sksec = sk->sk_security;
+	sksec = selinux_sock(sk);
 
 	ad.type = LSM_AUDIT_DATA_NET;
 	ad.u.net = &net;
@@ -5925,7 +5957,7 @@
 		u32 skb_sid;
 		struct sk_security_struct *sksec;
 
-		sksec = sk->sk_security;
+		sksec = selinux_sock(sk);
 		if (selinux_skb_peerlbl_sid(skb, family, &skb_sid))
 			return NF_DROP;
 		/* At this point, if the returned skb peerlbl is SECSID_NULL
@@ -5954,7 +5986,7 @@
 	} else {
 		/* Locally generated packet, fetch the security label from the
 		 * associated socket. */
-		struct sk_security_struct *sksec = sk->sk_security;
+		struct sk_security_struct *sksec = selinux_sock(sk);
 		peer_sid = sksec->sid;
 		secmark_perm = PACKET__SEND;
 	}
@@ -6019,7 +6051,7 @@
 	unsigned int data_len = skb->len;
 	unsigned char *data = skb->data;
 	struct nlmsghdr *nlh;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	u16 sclass = sksec->sclass;
 	u32 perm;
 
@@ -6467,7 +6499,7 @@
 			goto bad;
 	}
 
-	if (!strcmp(name, "current"))
+	if (!strcmp(name, "current") || !strcmp(name, "context"))
 		sid = __tsec->sid;
 	else if (!strcmp(name, "prev"))
 		sid = __tsec->osid;
@@ -6509,6 +6541,17 @@
 	/*
 	 * Basic control over ability to set these attributes at all.
 	 */
+
+	/*
+	 * For setting display, we only perform a permission check;
+	 * the actual update to the display value is handled by the
+	 * LSM framework.
+	 */
+	if (!strcmp(name, "display"))
+		return avc_has_perm(&selinux_state,
+				    mysid, mysid, SECCLASS_PROCESS2,
+				    PROCESS2__SETDISPLAY, NULL);
+
 	if (!strcmp(name, "exec"))
 		error = avc_has_perm(&selinux_state,
 				     mysid, mysid, SECCLASS_PROCESS,
@@ -6690,8 +6733,8 @@
  */
 static int selinux_inode_setsecctx(struct dentry *dentry, void *ctx, u32 ctxlen)
 {
-	return __vfs_setxattr_noperm(&init_user_ns, dentry, XATTR_NAME_SELINUX,
-				     ctx, ctxlen, 0);
+	return __vfs_setxattr_locked(&init_user_ns, dentry, XATTR_NAME_SELINUX,
+				       ctx, ctxlen, 0, NULL);
 }
 
 static int selinux_inode_getsecctx(struct inode *inode, void **ctx, u32 *ctxlen)
@@ -7048,6 +7091,7 @@
 	.lbs_ipc = sizeof(struct ipc_security_struct),
 	.lbs_msg_msg = sizeof(struct msg_security_struct),
 	.lbs_superblock = sizeof(struct superblock_security_struct),
+	.lbs_sock = sizeof(struct sk_security_struct),
 };
 
 #ifdef CONFIG_PERF_EVENTS
@@ -7111,6 +7155,11 @@
 }
 #endif
 
+struct lsm_id selinux_lsmid __lsm_ro_after_init = {
+	.lsm  = "selinux",
+	.slot = LSMBLOB_NEEDED
+};
+
 /*
  * IMPORTANT NOTE: When adding new hooks, please be careful to keep this order:
  * 1. any hooks that don't belong to (2.) or (3.) below,
@@ -7198,6 +7247,7 @@
 	LSM_HOOK_INIT(file_permission, selinux_file_permission),
 	LSM_HOOK_INIT(file_alloc_security, selinux_file_alloc_security),
 	LSM_HOOK_INIT(file_ioctl, selinux_file_ioctl),
+	LSM_HOOK_INIT(file_ioctl_compat, selinux_file_ioctl_compat),
 	LSM_HOOK_INIT(mmap_file, selinux_mmap_file),
 	LSM_HOOK_INIT(mmap_addr, selinux_mmap_addr),
 	LSM_HOOK_INIT(file_mprotect, selinux_file_mprotect),
@@ -7424,7 +7474,8 @@
 
 	hashtab_cache_init();
 
-	security_add_hooks(selinux_hooks, ARRAY_SIZE(selinux_hooks), "selinux");
+	security_add_hooks(selinux_hooks, ARRAY_SIZE(selinux_hooks),
+			   &selinux_lsmid);
 
 	if (avc_add_callback(selinux_netcache_avc_callback, AVC_CALLBACK_RESET))
 		panic("SELinux: Unable to register AVC netcache callback\n");
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ima.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ima.c
@@ -77,7 +77,7 @@
 	size_t policy_len;
 	int rc = 0;
 
-	WARN_ON(!mutex_is_locked(&state->policy_mutex));
+	lockdep_assert_held(&state->policy_mutex);
 
 	state_str = selinux_ima_collect_state(state);
 	if (!state_str) {
@@ -117,7 +117,7 @@
  */
 void selinux_ima_measure_state(struct selinux_state *state)
 {
-	WARN_ON(mutex_is_locked(&state->policy_mutex));
+	lockdep_assert_not_held(&state->policy_mutex);
 
 	mutex_lock(&state->policy_mutex);
 	selinux_ima_measure_state_locked(state);
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/include/audit.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/include/audit.h
@@ -18,12 +18,14 @@
  *	@op: the operater the rule uses
  *	@rulestr: the text "target" of the rule
  *	@rule: pointer to the new rule structure returned via this
+ *	@gfp: GFP flag used for kmalloc
  *
  *	Returns 0 if successful, -errno if not.  On success, the rule structure
  *	will be allocated internally.  The caller must free this structure with
  *	selinux_audit_rule_free() after use.
  */
-int selinux_audit_rule_init(u32 field, u32 op, char *rulestr, void **rule);
+int selinux_audit_rule_init(u32 field, u32 op, char *rulestr, void **rule,
+			    gfp_t gfp);
 
 /**
  *	selinux_audit_rule_free - free an selinux audit rule structure.
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/include/classmap.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/include/classmap.h
@@ -53,7 +53,7 @@
 	    "execmem", "execstack", "execheap", "setkeycreate",
 	    "setsockcreate", "getrlimit", NULL } },
 	{ "process2",
-	  { "nnp_transition", "nosuid_transition", NULL } },
+	  { "nnp_transition", "nosuid_transition", "setdisplay", NULL } },
 	{ "system",
 	  { "ipc_info", "syslog_read", "syslog_mod",
 	    "syslog_console", "module_request", "module_load", NULL } },
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/include/objsec.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/include/objsec.h
@@ -194,4 +194,9 @@
 	return superblock->s_security + selinux_blob_sizes.lbs_superblock;
 }
 
+static inline struct sk_security_struct *selinux_sock(const struct sock *sock)
+{
+	return sock->sk_security + selinux_blob_sizes.lbs_sock;
+}
+
 #endif /* _SELINUX_OBJSEC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/include/policycap.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/include/policycap.h
@@ -11,6 +11,7 @@
 	POLICYDB_CAPABILITY_CGROUPSECLABEL,
 	POLICYDB_CAPABILITY_NNP_NOSUID_TRANSITION,
 	POLICYDB_CAPABILITY_GENFS_SECLABEL_SYMLINKS,
+	POLICYDB_CAPABILITY_IOCTL_SKIP_CLOEXEC,
 	__POLICYDB_CAPABILITY_MAX
 };
 #define POLICYDB_CAPABILITY_MAX (__POLICYDB_CAPABILITY_MAX - 1)
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/include/policycap_names.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/include/policycap_names.h
@@ -12,7 +12,8 @@
 	"always_check_network",
 	"cgroup_seclabel",
 	"nnp_nosuid_transition",
-	"genfs_seclabel_symlinks"
+	"genfs_seclabel_symlinks",
+	"ioctl_skip_cloexec"
 };
 
 #endif /* _SELINUX_POLICYCAP_NAMES_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/include/security.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/include/security.h
@@ -73,6 +73,7 @@
 struct netlbl_lsm_secattr;
 
 extern int selinux_enabled_boot;
+extern struct lsm_id selinux_lsmid;
 
 /*
  * type_datum properties
@@ -219,6 +220,13 @@
 	return READ_ONCE(state->policycap[POLICYDB_CAPABILITY_GENFS_SECLABEL_SYMLINKS]);
 }
 
+static inline bool selinux_policycap_ioctl_skip_cloexec(void)
+{
+	struct selinux_state *state = &selinux_state;
+
+	return READ_ONCE(state->policycap[POLICYDB_CAPABILITY_IOCTL_SKIP_CLOEXEC]);
+}
+
 struct selinux_policy_convert_data;
 
 struct selinux_load_state {
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/netlabel.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/netlabel.c
@@ -17,6 +17,7 @@
 #include <linux/gfp.h>
 #include <linux/ip.h>
 #include <linux/ipv6.h>
+#include <linux/lsm_hooks.h>
 #include <net/sock.h>
 #include <net/netlabel.h>
 #include <net/ip.h>
@@ -67,7 +68,7 @@
 static struct netlbl_lsm_secattr *selinux_netlbl_sock_genattr(struct sock *sk)
 {
 	int rc;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	struct netlbl_lsm_secattr *secattr;
 
 	if (sksec->nlbl_secattr != NULL)
@@ -100,14 +101,14 @@
 							const struct sock *sk,
 							u32 sid)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	struct netlbl_lsm_secattr *secattr = sksec->nlbl_secattr;
 
 	if (secattr == NULL)
 		return NULL;
 
 	if ((secattr->flags & NETLBL_SECATTR_SECID) &&
-	    (secattr->attr.secid == sid))
+	    (secattr->attr.lsmblob.secid[selinux_lsmid.slot] == sid))
 		return secattr;
 
 	return NULL;
@@ -235,7 +236,7 @@
 	 * being labeled by it's parent socket, if it is just exit */
 	sk = skb_to_full_sk(skb);
 	if (sk != NULL) {
-		struct sk_security_struct *sksec = sk->sk_security;
+		struct sk_security_struct *sksec = selinux_sock(sk);
 
 		if (sksec->nlbl_state != NLBL_REQSKB)
 			return 0;
@@ -273,7 +274,7 @@
 {
 	int rc;
 	struct netlbl_lsm_secattr secattr;
-	struct sk_security_struct *sksec = ep->base.sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(ep->base.sk);
 	struct sockaddr_in addr4;
 	struct sockaddr_in6 addr6;
 
@@ -352,7 +353,7 @@
  */
 void selinux_netlbl_inet_csk_clone(struct sock *sk, u16 family)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
 	if (family == PF_INET)
 		sksec->nlbl_state = NLBL_LABELED;
@@ -370,8 +371,8 @@
  */
 void selinux_netlbl_sctp_sk_clone(struct sock *sk, struct sock *newsk)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
-	struct sk_security_struct *newsksec = newsk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
+	struct sk_security_struct *newsksec = selinux_sock(newsk);
 
 	newsksec->nlbl_state = sksec->nlbl_state;
 }
@@ -389,7 +390,7 @@
 int selinux_netlbl_socket_post_create(struct sock *sk, u16 family)
 {
 	int rc;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	struct netlbl_lsm_secattr *secattr;
 
 	if (family != PF_INET && family != PF_INET6)
@@ -504,7 +505,7 @@
 {
 	int rc = 0;
 	struct sock *sk = sock->sk;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	struct netlbl_lsm_secattr secattr;
 
 	if (selinux_netlbl_option(level, optname) &&
@@ -542,7 +543,7 @@
 						struct sockaddr *addr)
 {
 	int rc;
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 	struct netlbl_lsm_secattr *secattr;
 
 	/* connected sockets are allowed to disconnect when the address family
@@ -581,7 +582,7 @@
 int selinux_netlbl_socket_connect_locked(struct sock *sk,
 					 struct sockaddr *addr)
 {
-	struct sk_security_struct *sksec = sk->sk_security;
+	struct sk_security_struct *sksec = selinux_sock(sk);
 
 	if (sksec->nlbl_state != NLBL_REQSKB &&
 	    sksec->nlbl_state != NLBL_CONNLABELED)
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/selinuxfs.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/selinuxfs.c
@@ -619,6 +619,13 @@
 	ssize_t length;
 	void *data = NULL;
 
+	/* no partial writes */
+	if (*ppos)
+		return -EINVAL;
+	/* no empty policies */
+	if (!count)
+		return -EINVAL;
+
 	mutex_lock(&fsi->state->policy_mutex);
 
 	length = avc_has_perm(&selinux_state,
@@ -627,26 +634,21 @@
 	if (length)
 		goto out;
 
-	/* No partial writes. */
-	length = -EINVAL;
-	if (*ppos != 0)
-		goto out;
-
-	length = -ENOMEM;
 	data = vmalloc(count);
-	if (!data)
+	if (!data) {
+		length = -ENOMEM;
 		goto out;
-
-	length = -EFAULT;
-	if (copy_from_user(data, buf, count) != 0)
+	}
+	if (copy_from_user(data, buf, count) != 0) {
+		length = -EFAULT;
 		goto out;
+	}
 
 	length = security_load_policy(fsi->state, data, count, &load_state);
 	if (length) {
 		pr_warn_ratelimited("SELinux: failed to load policy\n");
 		goto out;
 	}
-
 	length = sel_make_policy_nodes(fsi, load_state.policy);
 	if (length) {
 		pr_warn_ratelimited("SELinux: failed to initialize selinuxfs\n");
@@ -655,13 +657,12 @@
 	}
 
 	selinux_policy_commit(fsi->state, &load_state);
-
 	length = count;
-
 	audit_log(audit_context(), GFP_KERNEL, AUDIT_MAC_POLICY_LOAD,
 		"auid=%u ses=%u lsm=selinux res=1",
 		from_kuid(&init_user_ns, audit_get_loginuid(current)),
 		audit_get_sessionid(current));
+
 out:
 	mutex_unlock(&fsi->state->policy_mutex);
 	vfree(data);
@@ -2127,6 +2128,8 @@
 	}
 
 	ret = sel_make_avc_files(dentry);
+	if (ret)
+		goto err;
 
 	dentry = sel_make_dir(sb->s_root, "ss", &fsi->last_ino);
 	if (IS_ERR(dentry)) {
@@ -2206,7 +2209,6 @@
 	.kill_sb	= sel_kill_sb,
 };
 
-static struct vfsmount *selinuxfs_mount __ro_after_init;
 struct path selinux_null __ro_after_init;
 
 static int __init init_sel_fs(void)
@@ -2228,18 +2230,21 @@
 		return err;
 	}
 
-	selinux_null.mnt = selinuxfs_mount = kern_mount(&sel_fs_type);
-	if (IS_ERR(selinuxfs_mount)) {
+	selinux_null.mnt = kern_mount(&sel_fs_type);
+	if (IS_ERR(selinux_null.mnt)) {
 		pr_err("selinuxfs:  could not mount!\n");
-		err = PTR_ERR(selinuxfs_mount);
-		selinuxfs_mount = NULL;
+		err = PTR_ERR(selinux_null.mnt);
+		selinux_null.mnt = NULL;
+		return err;
 	}
+
 	selinux_null.dentry = d_hash_and_lookup(selinux_null.mnt->mnt_root,
 						&null_name);
 	if (IS_ERR(selinux_null.dentry)) {
 		pr_err("selinuxfs:  could not lookup null!\n");
 		err = PTR_ERR(selinux_null.dentry);
 		selinux_null.dentry = NULL;
+		return err;
 	}
 
 	return err;
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/conditional.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/conditional.c
@@ -152,6 +152,8 @@
 	for (i = 0; i < p->cond_list_len; i++)
 		cond_node_destroy(&p->cond_list[i]);
 	kfree(p->cond_list);
+	p->cond_list = NULL;
+	p->cond_list_len = 0;
 }
 
 void cond_policydb_destroy(struct policydb *p)
@@ -441,7 +443,6 @@
 	return 0;
 err:
 	cond_list_destroy(p);
-	p->cond_list = NULL;
 	return rc;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/hashtab.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/hashtab.c
@@ -30,13 +30,20 @@
 
 int hashtab_init(struct hashtab *h, u32 nel_hint)
 {
-	h->size = hashtab_compute_size(nel_hint);
+	u32 size = hashtab_compute_size(nel_hint);
+
+	/* should already be zeroed, but better be safe */
 	h->nel = 0;
-	if (!h->size)
-		return 0;
+	h->size = 0;
+	h->htable = NULL;
 
-	h->htable = kcalloc(h->size, sizeof(*h->htable), GFP_KERNEL);
-	return h->htable ? 0 : -ENOMEM;
+	if (size) {
+		h->htable = kcalloc(size, sizeof(*h->htable), GFP_KERNEL);
+		if (!h->htable)
+			return -ENOMEM;
+		h->size = size;
+	}
+	return 0;
 }
 
 int __hashtab_insert(struct hashtab *h, struct hashtab_node **dst,
@@ -171,7 +178,8 @@
 			kmem_cache_free(hashtab_node_cachep, cur);
 		}
 	}
-	kmem_cache_free(hashtab_node_cachep, new);
+	kfree(new->htable);
+	memset(new, 0, sizeof(*new));
 	return -ENOMEM;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/policydb.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/policydb.c
@@ -2011,6 +2011,7 @@
 		if (!datum)
 			goto out;
 
+		datum->next = NULL;
 		*dst = datum;
 
 		/* ebitmap_read() will at least init the bitmap */
@@ -2023,7 +2024,6 @@
 			goto out;
 
 		datum->otype = le32_to_cpu(buf[0]);
-		datum->next = NULL;
 
 		dst = &datum->next;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/policydb.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/policydb.h
@@ -370,6 +370,8 @@
 {
 	size_t len = bytes * num;
 
+	if (len > fp->len)
+		return -EINVAL;
 	memcpy(fp->data, buf, len);
 	fp->data += len;
 	fp->len -= len;
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/services.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/services.c
@@ -971,7 +971,10 @@
 					xpermd->driver))
 			return;
 	} else {
-		BUG();
+		pr_warn_once(
+			"SELinux: unknown extended permission (%u) will be ignored\n",
+			node->datum.u.xperms->specified);
+		return;
 	}
 
 	if (node->key.specified == AVTAB_XPERMS_ALLOWED) {
@@ -1008,7 +1011,8 @@
 					node->datum.u.xperms->perms.p[i];
 		}
 	} else {
-		BUG();
+		pr_warn_once("SELinux: unknown specified key (%u)\n",
+			     node->key.specified);
 	}
 }
 
@@ -2021,7 +2025,8 @@
  * in `newc'.  Verify that the context is valid
  * under the new policy.
  */
-static int convert_context(struct context *oldc, struct context *newc, void *p)
+static int convert_context(struct context *oldc, struct context *newc, void *p,
+			   gfp_t gfp_flags)
 {
 	struct convert_context_args *args;
 	struct ocontext *oc;
@@ -2035,7 +2040,7 @@
 	args = p;
 
 	if (oldc->str) {
-		s = kstrdup(oldc->str, GFP_KERNEL);
+		s = kstrdup(oldc->str, gfp_flags);
 		if (!s)
 			return -ENOMEM;
 
@@ -2377,6 +2382,43 @@
 }
 
 /**
+ * ocontext_to_sid - Helper to safely get sid for an ocontext
+ * @sidtab: SID table
+ * @c: ocontext structure
+ * @index: index of the context entry (0 or 1)
+ * @out_sid: pointer to the resulting SID value
+ *
+ * For all ocontexts except OCON_ISID the SID fields are populated
+ * on-demand when needed. Since updating the SID value is an SMP-sensitive
+ * operation, this helper must be used to do that safely.
+ *
+ * WARNING: This function may return -ESTALE, indicating that the caller
+ * must retry the operation after re-acquiring the policy pointer!
+ */
+static int ocontext_to_sid(struct sidtab *sidtab, struct ocontext *c,
+			   size_t index, u32 *out_sid)
+{
+	int rc;
+	u32 sid;
+
+	/* Ensure the associated sidtab entry is visible to this thread. */
+	sid = smp_load_acquire(&c->sid[index]);
+	if (!sid) {
+		rc = sidtab_context_to_sid(sidtab, &c->context[index], &sid);
+		if (rc)
+			return rc;
+
+		/*
+		 * Ensure the new sidtab entry is visible to other threads
+		 * when they see the SID.
+		 */
+		smp_store_release(&c->sid[index], sid);
+	}
+	*out_sid = sid;
+	return 0;
+}
+
+/**
  * security_port_sid - Obtain the SID for a port.
  * @state: SELinux state
  * @protocol: protocol number
@@ -2414,17 +2456,13 @@
 	}
 
 	if (c) {
-		if (!c->sid[0]) {
-			rc = sidtab_context_to_sid(sidtab, &c->context[0],
-						   &c->sid[0]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
+		rc = ocontext_to_sid(sidtab, c, 0, out_sid);
+		if (rc == -ESTALE) {
+			rcu_read_unlock();
+			goto retry;
 		}
-		*out_sid = c->sid[0];
+		if (rc)
+			goto out;
 	} else {
 		*out_sid = SECINITSID_PORT;
 	}
@@ -2473,18 +2511,13 @@
 	}
 
 	if (c) {
-		if (!c->sid[0]) {
-			rc = sidtab_context_to_sid(sidtab,
-						   &c->context[0],
-						   &c->sid[0]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
+		rc = ocontext_to_sid(sidtab, c, 0, out_sid);
+		if (rc == -ESTALE) {
+			rcu_read_unlock();
+			goto retry;
 		}
-		*out_sid = c->sid[0];
+		if (rc)
+			goto out;
 	} else
 		*out_sid = SECINITSID_UNLABELED;
 
@@ -2533,17 +2566,13 @@
 	}
 
 	if (c) {
-		if (!c->sid[0]) {
-			rc = sidtab_context_to_sid(sidtab, &c->context[0],
-						   &c->sid[0]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
+		rc = ocontext_to_sid(sidtab, c, 0, out_sid);
+		if (rc == -ESTALE) {
+			rcu_read_unlock();
+			goto retry;
 		}
-		*out_sid = c->sid[0];
+		if (rc)
+			goto out;
 	} else
 		*out_sid = SECINITSID_UNLABELED;
 
@@ -2587,25 +2616,13 @@
 	}
 
 	if (c) {
-		if (!c->sid[0] || !c->sid[1]) {
-			rc = sidtab_context_to_sid(sidtab, &c->context[0],
-						   &c->sid[0]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
-			rc = sidtab_context_to_sid(sidtab, &c->context[1],
-						   &c->sid[1]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
+		rc = ocontext_to_sid(sidtab, c, 0, if_sid);
+		if (rc == -ESTALE) {
+			rcu_read_unlock();
+			goto retry;
 		}
-		*if_sid = c->sid[0];
+		if (rc)
+			goto out;
 	} else
 		*if_sid = SECINITSID_NETIF;
 
@@ -2697,18 +2714,13 @@
 	}
 
 	if (c) {
-		if (!c->sid[0]) {
-			rc = sidtab_context_to_sid(sidtab,
-						   &c->context[0],
-						   &c->sid[0]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
+		rc = ocontext_to_sid(sidtab, c, 0, out_sid);
+		if (rc == -ESTALE) {
+			rcu_read_unlock();
+			goto retry;
 		}
-		*out_sid = c->sid[0];
+		if (rc)
+			goto out;
 	} else {
 		*out_sid = SECINITSID_NODE;
 	}
@@ -2873,7 +2885,7 @@
 	u16 sclass;
 	struct genfs *genfs;
 	struct ocontext *c;
-	int rc, cmp = 0;
+	int cmp = 0;
 
 	while (path[0] == '/' && path[1] == '/')
 		path++;
@@ -2887,9 +2899,8 @@
 			break;
 	}
 
-	rc = -ENOENT;
 	if (!genfs || cmp)
-		goto out;
+		return -ENOENT;
 
 	for (c = genfs->head; c; c = c->next) {
 		len = strlen(c->u.name);
@@ -2898,20 +2909,10 @@
 			break;
 	}
 
-	rc = -ENOENT;
 	if (!c)
-		goto out;
-
-	if (!c->sid[0]) {
-		rc = sidtab_context_to_sid(sidtab, &c->context[0], &c->sid[0]);
-		if (rc)
-			goto out;
-	}
+		return -ENOENT;
 
-	*sid = c->sid[0];
-	rc = 0;
-out:
-	return rc;
+	return ocontext_to_sid(sidtab, c, 0, sid);
 }
 
 /**
@@ -2996,17 +2997,13 @@
 
 	if (c) {
 		sbsec->behavior = c->v.behavior;
-		if (!c->sid[0]) {
-			rc = sidtab_context_to_sid(sidtab, &c->context[0],
-						   &c->sid[0]);
-			if (rc == -ESTALE) {
-				rcu_read_unlock();
-				goto retry;
-			}
-			if (rc)
-				goto out;
+		rc = ocontext_to_sid(sidtab, c, 0, &sbsec->sid);
+		if (rc == -ESTALE) {
+			rcu_read_unlock();
+			goto retry;
 		}
-		sbsec->sid = c->sid[0];
+		if (rc)
+			goto out;
 	} else {
 		rc = __security_genfs_sid(policy, fstype, "/",
 					SECCLASS_DIR, &sbsec->sid);
@@ -3567,7 +3564,8 @@
 	}
 }
 
-int selinux_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule)
+int selinux_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule,
+			    gfp_t gfp)
 {
 	struct selinux_state *state = &selinux_state;
 	struct selinux_policy *policy;
@@ -3608,7 +3606,7 @@
 		return -EINVAL;
 	}
 
-	tmprule = kzalloc(sizeof(struct selinux_audit_rule), GFP_KERNEL);
+	tmprule = kzalloc(sizeof(struct selinux_audit_rule), gfp);
 	if (!tmprule)
 		return -ENOMEM;
 
@@ -3901,7 +3899,7 @@
 	if (secattr->flags & NETLBL_SECATTR_CACHE)
 		*sid = *(u32 *)secattr->cache->data;
 	else if (secattr->flags & NETLBL_SECATTR_SECID)
-		*sid = secattr->attr.secid;
+		*sid = secattr->attr.lsmblob.secid[selinux_lsmid.slot];
 	else if (secattr->flags & NETLBL_SECATTR_MLS_LVL) {
 		rc = -EIDRM;
 		ctx = sidtab_search(sidtab, SECINITSID_NETMSG);
@@ -3979,7 +3977,7 @@
 	if (secattr->domain == NULL)
 		goto out;
 
-	secattr->attr.secid = sid;
+	secattr->attr.lsmblob.secid[selinux_lsmid.slot] = sid;
 	secattr->flags |= NETLBL_SECATTR_DOMAIN_CPY | NETLBL_SECATTR_SECID;
 	mls_export_netlbl_lvl(policydb, ctx, secattr);
 	rc = mls_export_netlbl_cat(policydb, ctx, secattr);
@@ -4053,6 +4051,7 @@
 int security_read_state_kernel(struct selinux_state *state,
 			       void **data, size_t *len)
 {
+	int err;
 	struct selinux_policy *policy;
 
 	policy = rcu_dereference_protected(
@@ -4065,5 +4064,11 @@
 	if (!*data)
 		return -ENOMEM;
 
-	return __security_read_policy(policy, *data, len);
+	err = __security_read_policy(policy, *data, len);
+	if (err) {
+		vfree(*data);
+		*data = NULL;
+		*len = 0;
+	}
+	return err;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/sidtab.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/sidtab.c
@@ -325,7 +325,7 @@
 		}
 
 		rc = convert->func(context, &dst_convert->context,
-				   convert->args);
+				   convert->args, GFP_ATOMIC);
 		if (rc) {
 			context_destroy(&dst->context);
 			goto out_unlock;
@@ -404,7 +404,7 @@
 		while (i < SIDTAB_LEAF_ENTRIES && *pos < count) {
 			rc = convert->func(&esrc->ptr_leaf->entries[i].context,
 					   &edst->ptr_leaf->entries[i].context,
-					   convert->args);
+					   convert->args, GFP_KERNEL);
 			if (rc)
 				return rc;
 			(*pos)++;
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/ss/sidtab.h
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/ss/sidtab.h
@@ -65,7 +65,7 @@
 };
 
 struct sidtab_convert_params {
-	int (*func)(struct context *oldc, struct context *newc, void *args);
+	int (*func)(struct context *oldc, struct context *newc, void *args, gfp_t gfp_flags);
 	void *args;
 	struct sidtab *target;
 };
--- linux-xilinx-zynqmp-5.15.0.orig/security/selinux/xfrm.c
+++ linux-xilinx-zynqmp-5.15.0/security/selinux/xfrm.c
@@ -347,7 +347,7 @@
 	int rc;
 	struct xfrm_sec_ctx *ctx;
 	char *ctx_str = NULL;
-	int str_len;
+	u32 str_len;
 
 	if (!polsec)
 		return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/security/smack/smack.h
+++ linux-xilinx-zynqmp-5.15.0/security/smack/smack.h
@@ -120,6 +120,7 @@
 struct task_smack {
 	struct smack_known	*smk_task;	/* label for access control */
 	struct smack_known	*smk_forked;	/* label when forked */
+	struct smack_known	*smk_transmuted;/* label when transmuted */
 	struct list_head	smk_rules;	/* per task access rules */
 	struct mutex		smk_rules_lock;	/* lock for the rules */
 	struct list_head	smk_relabel;	/* transit allowed labels */
@@ -303,6 +304,7 @@
  * Shared data.
  */
 extern int smack_enabled __initdata;
+extern struct lsm_id smack_lsmid;
 extern int smack_cipso_direct;
 extern int smack_cipso_mapped;
 extern struct smack_known *smack_net_ambient;
@@ -363,6 +365,11 @@
 	return superblock->s_security + smack_blob_sizes.lbs_superblock;
 }
 
+static inline struct socket_smack *smack_sock(const struct sock *sock)
+{
+	return sock->sk_security + smack_blob_sizes.lbs_sock;
+}
+
 /*
  * Is the directory transmuting?
  */
--- linux-xilinx-zynqmp-5.15.0.orig/security/smack/smack_access.c
+++ linux-xilinx-zynqmp-5.15.0/security/smack/smack_access.c
@@ -523,8 +523,11 @@
 int smack_populate_secattr(struct smack_known *skp)
 {
 	int slen;
+	struct lsmblob *blob;
 
-	skp->smk_netlabel.attr.secid = skp->smk_secid;
+	blob = &skp->smk_netlabel.attr.lsmblob;
+	lsmblob_init(blob, 0);
+	blob->secid[smack_lsmid.slot] = skp->smk_secid;
 	skp->smk_netlabel.domain = skp->smk_known;
 	skp->smk_netlabel.cache = netlbl_secattr_cache_alloc(GFP_ATOMIC);
 	if (skp->smk_netlabel.cache != NULL) {
--- linux-xilinx-zynqmp-5.15.0.orig/security/smack/smack_lsm.c
+++ linux-xilinx-zynqmp-5.15.0/security/smack/smack_lsm.c
@@ -955,8 +955,9 @@
 				     const struct qstr *qstr, const char **name,
 				     void **value, size_t *len)
 {
+	struct task_smack *tsp = smack_cred(current_cred());
 	struct inode_smack *issp = smack_inode(inode);
-	struct smack_known *skp = smk_of_current();
+	struct smack_known *skp = smk_of_task(tsp);
 	struct smack_known *isp = smk_of_inode(inode);
 	struct smack_known *dsp = smk_of_inode(dir);
 	int may;
@@ -965,20 +966,34 @@
 		*name = XATTR_SMACK_SUFFIX;
 
 	if (value && len) {
-		rcu_read_lock();
-		may = smk_access_entry(skp->smk_known, dsp->smk_known,
-				       &skp->smk_rules);
-		rcu_read_unlock();
+		/*
+		 * If equal, transmuting already occurred in
+		 * smack_dentry_create_files_as(). No need to check again.
+		 */
+		if (tsp->smk_task != tsp->smk_transmuted) {
+			rcu_read_lock();
+			may = smk_access_entry(skp->smk_known, dsp->smk_known,
+					       &skp->smk_rules);
+			rcu_read_unlock();
+		}
 
 		/*
-		 * If the access rule allows transmutation and
-		 * the directory requests transmutation then
-		 * by all means transmute.
+		 * In addition to having smk_task equal to smk_transmuted,
+		 * if the access rule allows transmutation and the directory
+		 * requests transmutation then by all means transmute.
 		 * Mark the inode as changed.
 		 */
-		if (may > 0 && ((may & MAY_TRANSMUTE) != 0) &&
-		    smk_inode_transmutable(dir)) {
-			isp = dsp;
+		if ((tsp->smk_task == tsp->smk_transmuted) ||
+		    (may > 0 && ((may & MAY_TRANSMUTE) != 0) &&
+		     smk_inode_transmutable(dir))) {
+			/*
+			 * The caller of smack_dentry_create_files_as()
+			 * should have overridden the current cred, so the
+			 * inode label was already set correctly in
+			 * smack_inode_alloc_security().
+			 */
+			if (tsp->smk_task != tsp->smk_transmuted)
+				isp = dsp;
 			issp->smk_flags |= SMK_INODE_CHANGED;
 		}
 
@@ -1249,7 +1264,8 @@
 		check_star = 1;
 	} else if (strcmp(name, XATTR_NAME_SMACKTRANSMUTE) == 0) {
 		check_priv = 1;
-		if (size != TRANS_TRUE_SIZE ||
+		if (!S_ISDIR(d_backing_inode(dentry)->i_mode) ||
+		    size != TRANS_TRUE_SIZE ||
 		    strncmp(value, TRANS_TRUE, TRANS_TRUE_SIZE) != 0)
 			rc = -EINVAL;
 	} else
@@ -1414,10 +1430,19 @@
 	struct super_block *sbp;
 	struct inode *ip = (struct inode *)inode;
 	struct smack_known *isp;
+	struct inode_smack *ispp;
+	size_t label_len;
+	char *label = NULL;
 
-	if (strcmp(name, XATTR_SMACK_SUFFIX) == 0)
+	if (strcmp(name, XATTR_SMACK_SUFFIX) == 0) {
 		isp = smk_of_inode(inode);
-	else {
+	} else if (strcmp(name, XATTR_SMACK_TRANSMUTE) == 0) {
+		ispp = smack_inode(inode);
+		if (ispp->smk_flags & SMK_INODE_TRANSMUTE)
+			label = TRANS_TRUE;
+		else
+			label = "";
+	} else {
 		/*
 		 * The rest of the Smack xattrs are only on sockets.
 		 */
@@ -1429,7 +1454,7 @@
 		if (sock == NULL || sock->sk == NULL)
 			return -EOPNOTSUPP;
 
-		ssp = sock->sk->sk_security;
+		ssp = smack_sock(sock->sk);
 
 		if (strcmp(name, XATTR_SMACK_IPIN) == 0)
 			isp = ssp->smk_in;
@@ -1439,13 +1464,18 @@
 			return -EOPNOTSUPP;
 	}
 
+	if (!label)
+		label = isp->smk_known;
+
+	label_len = strlen(label);
+
 	if (alloc) {
-		*buffer = kstrdup(isp->smk_known, GFP_KERNEL);
+		*buffer = kstrdup(label, GFP_KERNEL);
 		if (*buffer == NULL)
 			return -ENOMEM;
 	}
 
-	return strlen(isp->smk_known);
+	return label_len;
 }
 
 
@@ -1811,7 +1841,7 @@
 
 	if (inode->i_sb->s_magic == SOCKFS_MAGIC) {
 		sock = SOCKET_I(inode);
-		ssp = sock->sk->sk_security;
+		ssp = smack_sock(sock->sk);
 		tsp = smack_cred(current_cred());
 		/*
 		 * If the receiving process can't write to the
@@ -2232,11 +2262,7 @@
 static int smack_sk_alloc_security(struct sock *sk, int family, gfp_t gfp_flags)
 {
 	struct smack_known *skp = smk_of_current();
-	struct socket_smack *ssp;
-
-	ssp = kzalloc(sizeof(struct socket_smack), gfp_flags);
-	if (ssp == NULL)
-		return -ENOMEM;
+	struct socket_smack *ssp = smack_sock(sk);
 
 	/*
 	 * Sockets created by kernel threads receive web label.
@@ -2250,11 +2276,10 @@
 	}
 	ssp->smk_packet = NULL;
 
-	sk->sk_security = ssp;
-
 	return 0;
 }
 
+#ifdef SMACK_IPV6_PORT_LABELING
 /**
  * smack_sk_free_security - Free a socket blob
  * @sk: the socket
@@ -2263,7 +2288,6 @@
  */
 static void smack_sk_free_security(struct sock *sk)
 {
-#ifdef SMACK_IPV6_PORT_LABELING
 	struct smk_port_label *spp;
 
 	if (sk->sk_family == PF_INET6) {
@@ -2276,9 +2300,8 @@
 		}
 		rcu_read_unlock();
 	}
-#endif
-	kfree(sk->sk_security);
 }
+#endif
 
 /**
 * smack_ipv4host_label - check host based restrictions
@@ -2391,7 +2414,7 @@
  */
 static int smack_netlbl_add(struct sock *sk)
 {
-	struct socket_smack *ssp = sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sk);
 	struct smack_known *skp = ssp->smk_out;
 	int rc;
 
@@ -2455,7 +2478,7 @@
 	struct smack_known *skp;
 	int rc = 0;
 	struct smack_known *hkp;
-	struct socket_smack *ssp = sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sk);
 	struct smk_audit_info ad;
 
 	rcu_read_lock();
@@ -2505,7 +2528,7 @@
 #ifdef CONFIG_AUDIT
 	smk_ad_init_net(&ad, __func__, LSM_AUDIT_DATA_NET, &net);
 	ad.a.u.net->family = PF_INET6;
-	ad.a.u.net->dport = ntohs(address->sin6_port);
+	ad.a.u.net->dport = address->sin6_port;
 	if (act == SMK_RECEIVING)
 		ad.a.u.net->v6info.saddr = address->sin6_addr;
 	else
@@ -2528,7 +2551,7 @@
 {
 	struct sock *sk = sock->sk;
 	struct sockaddr_in6 *addr6;
-	struct socket_smack *ssp = sock->sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sock->sk);
 	struct smk_port_label *spp;
 	unsigned short port = 0;
 
@@ -2617,7 +2640,7 @@
 				int act)
 {
 	struct smk_port_label *spp;
-	struct socket_smack *ssp = sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sk);
 	struct smack_known *skp = NULL;
 	unsigned short port;
 	struct smack_known *object;
@@ -2691,6 +2714,15 @@
 	if (value == NULL || size > SMK_LONGLABEL || size == 0)
 		return -EINVAL;
 
+	if (strcmp(name, XATTR_SMACK_TRANSMUTE) == 0) {
+		if (!S_ISDIR(inode->i_mode) || size != TRANS_TRUE_SIZE ||
+		    strncmp(value, TRANS_TRUE, TRANS_TRUE_SIZE) != 0)
+			return -EINVAL;
+
+		nsp->smk_flags |= SMK_INODE_TRANSMUTE;
+		return 0;
+	}
+
 	skp = smk_import_entry(value, size);
 	if (IS_ERR(skp))
 		return PTR_ERR(skp);
@@ -2710,7 +2742,7 @@
 	if (sock == NULL || sock->sk == NULL)
 		return -EOPNOTSUPP;
 
-	ssp = sock->sk->sk_security;
+	ssp = smack_sock(sock->sk);
 
 	if (strcmp(name, XATTR_SMACK_IPIN) == 0)
 		ssp->smk_in = skp;
@@ -2758,7 +2790,7 @@
 	 * Sockets created by kernel threads receive web label.
 	 */
 	if (unlikely(current->flags & PF_KTHREAD)) {
-		ssp = sock->sk->sk_security;
+		ssp = smack_sock(sock->sk);
 		ssp->smk_in = &smack_known_web;
 		ssp->smk_out = &smack_known_web;
 	}
@@ -2783,8 +2815,8 @@
 static int smack_socket_socketpair(struct socket *socka,
 		                   struct socket *sockb)
 {
-	struct socket_smack *asp = socka->sk->sk_security;
-	struct socket_smack *bsp = sockb->sk->sk_security;
+	struct socket_smack *asp = smack_sock(socka->sk);
+	struct socket_smack *bsp = smack_sock(sockb->sk);
 
 	asp->smk_packet = bsp->smk_out;
 	bsp->smk_packet = asp->smk_out;
@@ -2847,7 +2879,7 @@
 		if (__is_defined(SMACK_IPV6_SECMARK_LABELING))
 			rsp = smack_ipv6host_label(sip);
 		if (rsp != NULL) {
-			struct socket_smack *ssp = sock->sk->sk_security;
+			struct socket_smack *ssp = smack_sock(sock->sk);
 
 			rc = smk_ipv6_check(ssp->smk_out, rsp, sip,
 					    SMK_CONNECTING);
@@ -3484,7 +3516,7 @@
 	char *cp;
 	int slen;
 
-	if (strcmp(name, "current") != 0)
+	if (strcmp(name, "current") != 0 && strcmp(name, "context") != 0)
 		return -EINVAL;
 
 	cp = kstrdup(skp->smk_known, GFP_KERNEL);
@@ -3515,6 +3547,13 @@
 	struct smack_known_list_elem *sklep;
 	int rc;
 
+	/*
+	 * Allow the /proc/.../attr/current and SO_PEERSEC "display"
+	 * to be reset at will.
+	 */
+	if (strcmp(name, "display") == 0)
+		return 0;
+
 	if (!smack_privileged(CAP_MAC_ADMIN) && list_empty(&tsp->smk_relabel))
 		return -EPERM;
 
@@ -3575,9 +3614,9 @@
 {
 	struct smack_known *skp;
 	struct smack_known *okp;
-	struct socket_smack *ssp = sock->sk_security;
-	struct socket_smack *osp = other->sk_security;
-	struct socket_smack *nsp = newsk->sk_security;
+	struct socket_smack *ssp = smack_sock(sock);
+	struct socket_smack *osp = smack_sock(other);
+	struct socket_smack *nsp = smack_sock(newsk);
 	struct smk_audit_info ad;
 	int rc = 0;
 #ifdef CONFIG_AUDIT
@@ -3602,12 +3641,18 @@
 		}
 	}
 
-	/*
-	 * Cross reference the peer labels for SO_PEERSEC.
-	 */
 	if (rc == 0) {
+		/*
+		 * Cross reference the peer labels for SO_PEERSEC.
+		 */
 		nsp->smk_packet = ssp->smk_out;
 		ssp->smk_packet = osp->smk_out;
+
+		/*
+		 * new/child/established socket must inherit listening socket labels
+		 */
+		nsp->smk_out = osp->smk_out;
+		nsp->smk_in  = osp->smk_in;
 	}
 
 	return rc;
@@ -3623,8 +3668,8 @@
  */
 static int smack_unix_may_send(struct socket *sock, struct socket *other)
 {
-	struct socket_smack *ssp = sock->sk->sk_security;
-	struct socket_smack *osp = other->sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sock->sk);
+	struct socket_smack *osp = smack_sock(other->sk);
 	struct smk_audit_info ad;
 	int rc;
 
@@ -3661,7 +3706,7 @@
 	struct sockaddr_in6 *sap = (struct sockaddr_in6 *) msg->msg_name;
 #endif
 #ifdef SMACK_IPV6_SECMARK_LABELING
-	struct socket_smack *ssp = sock->sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sock->sk);
 	struct smack_known *rsp;
 #endif
 	int rc = 0;
@@ -3724,7 +3769,7 @@
 		/*
 		 * Looks like a fallback, which gives us a secid.
 		 */
-		return smack_from_secid(sap->attr.secid);
+		return smack_from_secid(sap->attr.lsmblob.secid[smack_lsmid.slot]);
 
 	if ((sap->flags & NETLBL_SECATTR_MLS_LVL) != 0) {
 		/*
@@ -3773,6 +3818,7 @@
 			return &smack_known_web;
 		return &smack_known_star;
 	}
+
 	/*
 	 * Without guidance regarding the smack value
 	 * for the packet fall back on the network
@@ -3895,7 +3941,7 @@
  */
 static int smack_socket_sock_rcv_skb(struct sock *sk, struct sk_buff *skb)
 {
-	struct socket_smack *ssp = sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sk);
 	struct smack_known *skp = NULL;
 	int rc = 0;
 	struct smk_audit_info ad;
@@ -3999,7 +4045,7 @@
 	int slen = 1;
 	int rc = 0;
 
-	ssp = sock->sk->sk_security;
+	ssp = smack_sock(sock->sk);
 	if (ssp->smk_packet != NULL) {
 		rcp = ssp->smk_packet->smk_known;
 		slen = strlen(rcp) + 1;
@@ -4048,7 +4094,7 @@
 
 	switch (family) {
 	case PF_UNIX:
-		ssp = sock->sk->sk_security;
+		ssp = smack_sock(sock->sk);
 		s = ssp->smk_out->smk_secid;
 		break;
 	case PF_INET:
@@ -4097,7 +4143,7 @@
 	    (sk->sk_family != PF_INET && sk->sk_family != PF_INET6))
 		return;
 
-	ssp = sk->sk_security;
+	ssp = smack_sock(sk);
 	ssp->smk_in = skp;
 	ssp->smk_out = skp;
 	/* cssp->smk_packet is already set in smack_inet_csk_clone() */
@@ -4117,7 +4163,7 @@
 {
 	u16 family = sk->sk_family;
 	struct smack_known *skp;
-	struct socket_smack *ssp = sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sk);
 	struct sockaddr_in addr;
 	struct iphdr *hdr;
 	struct smack_known *hskp;
@@ -4186,7 +4232,7 @@
 	rcu_read_unlock();
 
 	if (hskp == NULL)
-		rc = netlbl_req_setattr(req, &skp->smk_netlabel);
+		rc = netlbl_req_setattr(req, &ssp->smk_out->smk_netlabel);
 	else
 		netlbl_req_delattr(req);
 
@@ -4203,7 +4249,7 @@
 static void smack_inet_csk_clone(struct sock *sk,
 				 const struct request_sock *req)
 {
-	struct socket_smack *ssp = sk->sk_security;
+	struct socket_smack *ssp = smack_sock(sk);
 	struct smack_known *skp;
 
 	if (req->peer_secid != 0) {
@@ -4448,11 +4494,13 @@
  * @op: required testing operator (=, !=, >, <, ...)
  * @rulestr: smack label to be audited
  * @vrule: pointer to save our own audit rule representation
+ * @gfp: type of the memory for the allocation
  *
  * Prepare to audit cases where (@field @op @rulestr) is true.
  * The label to be audited is created if necessay.
  */
-static int smack_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule)
+static int smack_audit_rule_init(u32 field, u32 op, char *rulestr, void **vrule,
+				 gfp_t gfp)
 {
 	struct smack_known *skp;
 	char **rule = (char **)vrule;
@@ -4602,8 +4650,8 @@
 
 static int smack_inode_setsecctx(struct dentry *dentry, void *ctx, u32 ctxlen)
 {
-	return __vfs_setxattr_noperm(&init_user_ns, dentry, XATTR_NAME_SMACK,
-				     ctx, ctxlen, 0);
+	return __vfs_setxattr_locked(&init_user_ns, dentry, XATTR_NAME_SMACK,
+				     ctx, ctxlen, 0, NULL);
 }
 
 static int smack_inode_getsecctx(struct inode *inode, void **ctx, u32 *ctxlen)
@@ -4634,7 +4682,7 @@
 	/*
 	 * Get label from overlay inode and set it in create_sid
 	 */
-	isp = smack_inode(d_inode(dentry->d_parent));
+	isp = smack_inode(d_inode(dentry));
 	skp = isp->smk_inode;
 	tsp->smk_task = skp;
 	*new = new_creds;
@@ -4685,8 +4733,10 @@
 		 * providing access is transmuting use the containing
 		 * directory label instead of the process label.
 		 */
-		if (may > 0 && (may & MAY_TRANSMUTE))
+		if (may > 0 && (may & MAY_TRANSMUTE)) {
 			ntsp->smk_task = isp->smk_inode;
+			ntsp->smk_transmuted = ntsp->smk_task;
+		}
 	}
 	return 0;
 }
@@ -4698,6 +4748,12 @@
 	.lbs_ipc = sizeof(struct smack_known *),
 	.lbs_msg_msg = sizeof(struct smack_known *),
 	.lbs_superblock = sizeof(struct superblock_smack),
+	.lbs_sock = sizeof(struct socket_smack),
+};
+
+struct lsm_id smack_lsmid __lsm_ro_after_init = {
+	.lsm  = "smack",
+	.slot = LSMBLOB_NEEDED
 };
 
 static struct security_hook_list smack_hooks[] __lsm_ro_after_init = {
@@ -4736,6 +4792,7 @@
 
 	LSM_HOOK_INIT(file_alloc_security, smack_file_alloc_security),
 	LSM_HOOK_INIT(file_ioctl, smack_file_ioctl),
+	LSM_HOOK_INIT(file_ioctl_compat, smack_file_ioctl),
 	LSM_HOOK_INIT(file_lock, smack_file_lock),
 	LSM_HOOK_INIT(file_fcntl, smack_file_fcntl),
 	LSM_HOOK_INIT(mmap_file, smack_mmap_file),
@@ -4807,7 +4864,9 @@
 	LSM_HOOK_INIT(socket_getpeersec_stream, smack_socket_getpeersec_stream),
 	LSM_HOOK_INIT(socket_getpeersec_dgram, smack_socket_getpeersec_dgram),
 	LSM_HOOK_INIT(sk_alloc_security, smack_sk_alloc_security),
+#ifdef SMACK_IPV6_PORT_LABELING
 	LSM_HOOK_INIT(sk_free_security, smack_sk_free_security),
+#endif
 	LSM_HOOK_INIT(sock_graft, smack_sock_graft),
 	LSM_HOOK_INIT(inet_conn_request, smack_inet_conn_request),
 	LSM_HOOK_INIT(inet_csk_clone, smack_inet_csk_clone),
@@ -4897,7 +4956,7 @@
 	/*
 	 * Register with LSM
 	 */
-	security_add_hooks(smack_hooks, ARRAY_SIZE(smack_hooks), "smack");
+	security_add_hooks(smack_hooks, ARRAY_SIZE(smack_hooks), &smack_lsmid);
 	smack_enabled = 1;
 
 	pr_info("Smack:  Initializing.\n");
--- linux-xilinx-zynqmp-5.15.0.orig/security/smack/smack_netfilter.c
+++ linux-xilinx-zynqmp-5.15.0/security/smack/smack_netfilter.c
@@ -28,8 +28,8 @@
 	struct socket_smack *ssp;
 	struct smack_known *skp;
 
-	if (sk && sk->sk_security) {
-		ssp = sk->sk_security;
+	if (sk && smack_sock(sk)) {
+		ssp = smack_sock(sk);
 		skp = ssp->smk_out;
 		skb->secmark = skp->smk_secid;
 	}
@@ -46,8 +46,8 @@
 	struct socket_smack *ssp;
 	struct smack_known *skp;
 
-	if (sk && sk->sk_security) {
-		ssp = sk->sk_security;
+	if (sk && smack_sock(sk)) {
+		ssp = smack_sock(sk);
 		skp = ssp->smk_out;
 		skb->secmark = skp->smk_secid;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/security/smack/smackfs.c
+++ linux-xilinx-zynqmp-5.15.0/security/smack/smackfs.c
@@ -185,7 +185,8 @@
 
 	nap->loginuid = audit_get_loginuid(current);
 	nap->sessionid = audit_get_sessionid(current);
-	nap->secid = skp->smk_secid;
+	lsmblob_init(&nap->lsmdata, 0);
+	nap->lsmdata.secid[smack_lsmid.slot] = skp->smk_secid;
 }
 
 /*
@@ -693,9 +694,7 @@
 		printk(KERN_WARNING "%s:%d remove rc = %d\n",
 		       __func__, __LINE__, rc);
 
-	doip = kmalloc(sizeof(struct cipso_v4_doi), GFP_KERNEL);
-	if (doip == NULL)
-		panic("smack:  Failed to initialize cipso DOI.\n");
+	doip = kmalloc(sizeof(struct cipso_v4_doi), GFP_KERNEL | __GFP_NOFAIL);
 	doip->map.std = NULL;
 	doip->doi = smk_cipso_doi_value;
 	doip->type = CIPSO_V4_MAP_PASS;
@@ -714,7 +713,7 @@
 	if (rc != 0) {
 		printk(KERN_WARNING "%s:%d map add rc = %d\n",
 		       __func__, __LINE__, rc);
-		kfree(doip);
+		netlbl_cfg_cipsov4_del(doip->doi, &nai);
 		return;
 	}
 }
@@ -831,6 +830,7 @@
 static ssize_t smk_set_cipso(struct file *file, const char __user *buf,
 				size_t count, loff_t *ppos, int format)
 {
+	struct netlbl_lsm_catmap *old_cat;
 	struct smack_known *skp;
 	struct netlbl_lsm_secattr ncats;
 	char mapcatset[SMK_CIPSOLEN];
@@ -896,7 +896,7 @@
 	}
 
 	ret = sscanf(rule, "%d", &catlen);
-	if (ret != 1 || catlen > SMACK_CIPSO_MAXCATNUM)
+	if (ret != 1 || catlen < 0 || catlen > SMACK_CIPSO_MAXCATNUM)
 		goto out;
 
 	if (format == SMK_FIXED24_FMT &&
@@ -920,9 +920,11 @@
 
 	rc = smk_netlbl_mls(maplevel, mapcatset, &ncats, SMK_CIPSOLEN);
 	if (rc >= 0) {
-		netlbl_catmap_free(skp->smk_netlabel.attr.mls.cat);
-		skp->smk_netlabel.attr.mls.cat = ncats.attr.mls.cat;
+		old_cat = skp->smk_netlabel.attr.mls.cat;
+		rcu_assign_pointer(skp->smk_netlabel.attr.mls.cat, ncats.attr.mls.cat);
 		skp->smk_netlabel.attr.mls.lvl = ncats.attr.mls.lvl;
+		synchronize_rcu();
+		netlbl_catmap_free(old_cat);
 		rc = count;
 		/*
 		 * This mapping may have been cached, so clear the cache.
@@ -1142,6 +1144,7 @@
 static ssize_t smk_write_net4addr(struct file *file, const char __user *buf,
 				size_t count, loff_t *ppos)
 {
+	struct lsmblob lsmblob;
 	struct smk_net4addr *snp;
 	struct sockaddr_in newname;
 	char *smack;
@@ -1273,10 +1276,13 @@
 	 * this host so that incoming packets get labeled.
 	 * but only if we didn't get the special CIPSO option
 	 */
-	if (rc == 0 && skp != NULL)
+	if (rc == 0 && skp != NULL) {
+		lsmblob_init(&lsmblob, 0);
+		lsmblob.secid[smack_lsmid.slot] = snp->smk_label->smk_secid;
 		rc = netlbl_cfg_unlbl_static_add(&init_net, NULL,
-			&snp->smk_host, &snp->smk_mask, PF_INET,
-			snp->smk_label->smk_secid, &audit_info);
+			&snp->smk_host, &snp->smk_mask, PF_INET, &lsmblob,
+			&audit_info);
+	}
 
 	if (rc == 0)
 		rc = count;
--- linux-xilinx-zynqmp-5.15.0.orig/security/tomoyo/Makefile
+++ linux-xilinx-zynqmp-5.15.0/security/tomoyo/Makefile
@@ -10,7 +10,7 @@
 quiet_cmd_policy  = POLICY  $@
       cmd_policy  = ($(call do_policy,profile); $(call do_policy,exception_policy); $(call do_policy,domain_policy); $(call do_policy,manager); $(call do_policy,stat)) >$@
 
-$(obj)/builtin-policy.h: $(wildcard $(obj)/policy/*.conf $(src)/policy/*.conf.default) FORCE
+$(obj)/builtin-policy.h: $(wildcard $(obj)/policy/*.conf $(srctree)/$(src)/policy/*.conf.default) FORCE
 	$(call if_changed,policy)
 
 $(obj)/common.o: $(obj)/builtin-policy.h
--- linux-xilinx-zynqmp-5.15.0.orig/security/tomoyo/common.c
+++ linux-xilinx-zynqmp-5.15.0/security/tomoyo/common.c
@@ -2657,13 +2657,14 @@
 {
 	int error = buffer_len;
 	size_t avail_len = buffer_len;
-	char *cp0 = head->write_buf;
+	char *cp0;
 	int idx;
 
 	if (!head->write)
 		return -EINVAL;
 	if (mutex_lock_interruptible(&head->io_sem))
 		return -EINTR;
+	cp0 = head->write_buf;
 	head->read_user_buf_avail = 0;
 	idx = tomoyo_read_lock();
 	/* Read a line and dispatch it to the policy handler. */
@@ -2672,7 +2673,7 @@
 
 		if (head->w.avail >= head->writebuf_size - 1) {
 			const int len = head->writebuf_size * 2;
-			char *cp = kzalloc(len, GFP_NOFS);
+			char *cp = kzalloc(len, GFP_NOFS | __GFP_NOWARN);
 
 			if (!cp) {
 				error = -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/security/tomoyo/domain.c
+++ linux-xilinx-zynqmp-5.15.0/security/tomoyo/domain.c
@@ -723,10 +723,13 @@
 	ee->r.obj = &ee->obj;
 	ee->obj.path1 = bprm->file->f_path;
 	/* Get symlink's pathname of program. */
-	retval = -ENOENT;
 	exename.name = tomoyo_realpath_nofollow(original_name);
-	if (!exename.name)
-		goto out;
+	if (!exename.name) {
+		/* Fallback to realpath if symlink's pathname does not exist. */
+		exename.name = tomoyo_realpath_from_path(&bprm->file->f_path);
+		if (!exename.name)
+			goto out;
+	}
 	tomoyo_fill_path_info(&exename);
 retry:
 	/* Check 'aggregator' directive. */
--- linux-xilinx-zynqmp-5.15.0.orig/security/tomoyo/load_policy.c
+++ linux-xilinx-zynqmp-5.15.0/security/tomoyo/load_policy.c
@@ -24,7 +24,7 @@
 static int __init tomoyo_loader_setup(char *str)
 {
 	tomoyo_loader = str;
-	return 0;
+	return 1;
 }
 
 __setup("TOMOYO_loader=", tomoyo_loader_setup);
@@ -64,7 +64,7 @@
 static int __init tomoyo_trigger_setup(char *str)
 {
 	tomoyo_trigger = str;
-	return 0;
+	return 1;
 }
 
 __setup("TOMOYO_trigger=", tomoyo_trigger_setup);
--- linux-xilinx-zynqmp-5.15.0.orig/security/tomoyo/tomoyo.c
+++ linux-xilinx-zynqmp-5.15.0/security/tomoyo/tomoyo.c
@@ -521,6 +521,11 @@
 	}
 }
 
+static struct lsm_id tomoyo_lsmid __lsm_ro_after_init = {
+	.lsm  = "tomoyo",
+	.slot = LSMBLOB_NOT_NEEDED
+};
+
 /*
  * tomoyo_security_ops is a "struct security_operations" which is used for
  * registering TOMOYO.
@@ -546,6 +551,7 @@
 	LSM_HOOK_INIT(path_rename, tomoyo_path_rename),
 	LSM_HOOK_INIT(inode_getattr, tomoyo_inode_getattr),
 	LSM_HOOK_INIT(file_ioctl, tomoyo_file_ioctl),
+	LSM_HOOK_INIT(file_ioctl_compat, tomoyo_file_ioctl),
 	LSM_HOOK_INIT(path_chmod, tomoyo_path_chmod),
 	LSM_HOOK_INIT(path_chown, tomoyo_path_chown),
 	LSM_HOOK_INIT(path_chroot, tomoyo_path_chroot),
@@ -573,7 +579,8 @@
 	struct tomoyo_task *s = tomoyo_task(current);
 
 	/* register ourselves with the security framework */
-	security_add_hooks(tomoyo_hooks, ARRAY_SIZE(tomoyo_hooks), "tomoyo");
+	security_add_hooks(tomoyo_hooks, ARRAY_SIZE(tomoyo_hooks),
+			   &tomoyo_lsmid);
 	pr_info("TOMOYO Linux initialized\n");
 	s->domain_info = &tomoyo_kernel_domain;
 	atomic_inc(&tomoyo_kernel_domain.users);
--- linux-xilinx-zynqmp-5.15.0.orig/security/tomoyo/util.c
+++ linux-xilinx-zynqmp-5.15.0/security/tomoyo/util.c
@@ -1051,10 +1051,11 @@
 		return false;
 	if (!domain)
 		return true;
+	if (READ_ONCE(domain->flags[TOMOYO_DIF_QUOTA_WARNED]))
+		return false;
 	list_for_each_entry_rcu(ptr, &domain->acl_info_list, list,
 				srcu_read_lock_held(&tomoyo_ss)) {
 		u16 perm;
-		u8 i;
 
 		if (ptr->is_deleted)
 			continue;
@@ -1065,23 +1066,23 @@
 		 */
 		switch (ptr->type) {
 		case TOMOYO_TYPE_PATH_ACL:
-			data_race(perm = container_of(ptr, struct tomoyo_path_acl, head)->perm);
+			perm = data_race(container_of(ptr, struct tomoyo_path_acl, head)->perm);
 			break;
 		case TOMOYO_TYPE_PATH2_ACL:
-			data_race(perm = container_of(ptr, struct tomoyo_path2_acl, head)->perm);
+			perm = data_race(container_of(ptr, struct tomoyo_path2_acl, head)->perm);
 			break;
 		case TOMOYO_TYPE_PATH_NUMBER_ACL:
-			data_race(perm = container_of(ptr, struct tomoyo_path_number_acl, head)
+			perm = data_race(container_of(ptr, struct tomoyo_path_number_acl, head)
 				  ->perm);
 			break;
 		case TOMOYO_TYPE_MKDEV_ACL:
-			data_race(perm = container_of(ptr, struct tomoyo_mkdev_acl, head)->perm);
+			perm = data_race(container_of(ptr, struct tomoyo_mkdev_acl, head)->perm);
 			break;
 		case TOMOYO_TYPE_INET_ACL:
-			data_race(perm = container_of(ptr, struct tomoyo_inet_acl, head)->perm);
+			perm = data_race(container_of(ptr, struct tomoyo_inet_acl, head)->perm);
 			break;
 		case TOMOYO_TYPE_UNIX_ACL:
-			data_race(perm = container_of(ptr, struct tomoyo_unix_acl, head)->perm);
+			perm = data_race(container_of(ptr, struct tomoyo_unix_acl, head)->perm);
 			break;
 		case TOMOYO_TYPE_MANUAL_TASK_ACL:
 			perm = 0;
@@ -1089,21 +1090,17 @@
 		default:
 			perm = 1;
 		}
-		for (i = 0; i < 16; i++)
-			if (perm & (1 << i))
-				count++;
+		count += hweight16(perm);
 	}
 	if (count < tomoyo_profile(domain->ns, domain->profile)->
 	    pref[TOMOYO_PREF_MAX_LEARNING_ENTRY])
 		return true;
-	if (!domain->flags[TOMOYO_DIF_QUOTA_WARNED]) {
-		domain->flags[TOMOYO_DIF_QUOTA_WARNED] = true;
-		/* r->granted = false; */
-		tomoyo_write_log(r, "%s", tomoyo_dif[TOMOYO_DIF_QUOTA_WARNED]);
+	WRITE_ONCE(domain->flags[TOMOYO_DIF_QUOTA_WARNED], true);
+	/* r->granted = false; */
+	tomoyo_write_log(r, "%s", tomoyo_dif[TOMOYO_DIF_QUOTA_WARNED]);
 #ifndef CONFIG_SECURITY_TOMOYO_INSECURE_BUILTIN_SETTING
-		pr_warn("WARNING: Domain '%s' has too many ACLs to hold. Stopped learning mode.\n",
-			domain->domainname->name);
+	pr_warn("WARNING: Domain '%s' has too many ACLs to hold. Stopped learning mode.\n",
+		domain->domainname->name);
 #endif
-	}
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/security/yama/yama_lsm.c
+++ linux-xilinx-zynqmp-5.15.0/security/yama/yama_lsm.c
@@ -421,6 +421,11 @@
 	return rc;
 }
 
+static struct lsm_id yama_lsmid __lsm_ro_after_init = {
+	.lsm  = "yama",
+	.slot = LSMBLOB_NOT_NEEDED
+};
+
 static struct security_hook_list yama_hooks[] __lsm_ro_after_init = {
 	LSM_HOOK_INIT(ptrace_access_check, yama_ptrace_access_check),
 	LSM_HOOK_INIT(ptrace_traceme, yama_ptrace_traceme),
@@ -477,7 +482,7 @@
 static int __init yama_init(void)
 {
 	pr_info("Yama: becoming mindful.\n");
-	security_add_hooks(yama_hooks, ARRAY_SIZE(yama_hooks), "yama");
+	security_add_hooks(yama_hooks, ARRAY_SIZE(yama_hooks), &yama_lsmid);
 	yama_init_sysctl();
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/snapcraft.yaml
+++ linux-xilinx-zynqmp-5.15.0/snapcraft.yaml
@@ -0,0 +1,133 @@
+name: zynqmp-kernel
+summary: The Xilinx Kernel for ZynqMP SoCs
+description: The Xilinx Kernel for ZynqMP SoCs as a snap
+grade: devel
+confinement: devmode
+type: kernel
+adopt-info: kernel
+
+architectures:
+  - build-on: [amd64, arm64]
+    build-for: arm64
+
+build-base: core22
+assumes:
+  - kernel-assets
+
+parts:
+  kernel:
+    after:
+      - firmware
+    plugin: kernel
+    source: .
+    source-type: local
+    kernel-kconfigflavour: "xilinx-zynqmp"
+    kernel-with-firmware: false
+    kernel-enable-zfs-support: true
+    kernel-initrd-compression: lz4
+    kernel-initrd-stage-firmware: true
+    kernel-initrd-modules:
+      - libarc4
+      - tpm_tis
+      - sbp2
+      - usb-storage
+      - ehci-hcd
+      - uhci-hcd
+      - scsi_mod
+      - sr_mod
+      - sd_mod
+      - tls
+      - ina260_adc
+      - tpm_tis_spi
+      - scsi_dh_rdac
+      - scsi_dh_emc
+      - scsi_dh_alua
+      - autofs4
+      - rtc_zynqmp
+      - spi_zynqmp_gqspi
+      - i2c_cadence
+      - zynqmp_dpsub
+      - xhci_hcd
+      - xhci_pci
+      - efi_pstoreg
+      - ehci_hcdg
+      - tpmg
+      - tpm_crbg
+      - tpm_tisg
+      - tpm_tis_coreg
+      - xhci_pcig
+    kernel-kconfigs:
+      - CONFIG_SYSTEM_TRUSTED_KEYS=""
+      - CONFIG_SYSTEM_REVOCATION_KEYS=""
+    override-build: |
+      craftctl default
+      kernel_version=$(dpkg-parsechangelog -l ${CRAFT_PART_SRC}/debian.zynqmp/changelog -S version)
+      craftctl set version=${kernel_version}
+    override-prime: |
+      craftctl default
+      ${CRAFT_STAGE}/trim-firmware ${CRAFT_PRIME}
+    stage:
+      - config-*
+      - initrd.img
+      - kernel.img
+      - lib
+      - modules
+      - System.map-*
+      - Image.gz-*
+      - dtbs/xilinx/zynqmp-smk-k26-revA.dtb
+      - dtbs/xilinx/smk-k26-revA-sck-kr-g-revA.dtb
+      - dtbs/xilinx/smk-k26-revA-sck-kv-g-revA.dtb
+      - dtbs/xilinx/smk-k26-revA-sck-kr-g-revB.dtb
+      - dtbs/xilinx/smk-k26-revA-sck-kv-g-revB.dtb
+    prime:
+      - -initrd.img
+      - -kernel.img
+    organize:
+      Image.gz-*: Image.gz-5.15
+
+  firmware:
+    plugin: dump
+    source: https://git.launchpad.net/~canonical-kernel-snaps/+git/kernel-snaps-uc22
+    source-type: git
+    source-branch: main
+    stage-packages:
+      - linux-firmware
+    organize:
+      lib/firmware: firmware
+    prime:
+      - firmware
+
+  mkimage:
+    plugin: nil
+    after:
+      - kernel
+      - meta-files
+    build-packages:
+      - u-boot-tools
+      - device-tree-compiler
+    override-build:
+      mkimage -f ${CRAFT_STAGE}/meta/image-zynqmp.its ${CRAFT_STAGE}/image.fit
+    prime:
+      - image.fit
+
+  meta-files:
+    plugin: nil
+    source: meta-files
+    override-build: |
+      mkdir -p "$SNAPCRAFT_PART_INSTALL"/meta
+      cp -a * "$SNAPCRAFT_PART_INSTALL"/meta
+    stage:
+      - meta/image-zynqmp.its
+      - meta/kernel.yaml
+
+
+
+build-packages:
+    - android-tools-mkbootimg
+    - bison
+    - cpio
+    - dirmngr
+    - dpkg-dev
+    - flex
+    - gcc-aarch64-linux-gnu
+    - libelf-dev
--- linux-xilinx-zynqmp-5.15.0.orig/sound/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig SOUND
 	tristate "Sound card support"
-	depends on HAS_IOMEM
+	depends on HAS_IOMEM || INDIRECT_IOMEM
 	help
 	  If you have a sound card in your computer, i.e. if it can say more
 	  than an occasional beep, say Y.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/aoa/soundbus/i2sbus/core.c
+++ linux-xilinx-zynqmp-5.15.0/sound/aoa/soundbus/i2sbus/core.c
@@ -147,6 +147,7 @@
 	return rc;
 }
 
+/* Returns 1 if added, 0 for otherwise; don't return a negative value! */
 /* FIXME: look at device node refcounting */
 static int i2sbus_add_dev(struct macio_dev *macio,
 			  struct i2sbus_control *control,
@@ -213,7 +214,7 @@
 	 * either as the second one in that case is just a modem. */
 	if (!ok) {
 		kfree(dev);
-		return -ENODEV;
+		return 0;
 	}
 
 	mutex_init(&dev->lock);
@@ -302,6 +303,10 @@
 
 	if (soundbus_add_one(&dev->sound)) {
 		printk(KERN_DEBUG "i2sbus: device registration error!\n");
+		if (dev->sound.ofdev.dev.kobj.state_initialized) {
+			soundbus_dev_put(&dev->sound);
+			return 0;
+		}
 		goto err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/Makefile
+++ linux-xilinx-zynqmp-5.15.0/sound/core/Makefile
@@ -9,7 +9,9 @@
 snd-y += info.o
 snd-$(CONFIG_SND_OSSEMUL) += info_oss.o
 endif
+ifneq ($(CONFIG_M68K),y)
 snd-$(CONFIG_ISA_DMA_API) += isadma.o
+endif
 snd-$(CONFIG_SND_OSSEMUL) += sound_oss.o
 snd-$(CONFIG_SND_VMASTER) += vmaster.o
 snd-$(CONFIG_SND_JACK)	  += ctljack.o jack.o
@@ -31,7 +33,6 @@
 snd-rawmidi-objs  := rawmidi.o
 snd-timer-objs    := timer.o
 snd-hrtimer-objs  := hrtimer.o
-snd-rtctimer-objs := rtctimer.o
 snd-hwdep-objs    := hwdep.o
 snd-seq-device-objs := seq_device.o
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/control.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/control.c
@@ -127,6 +127,7 @@
 			if (control->vd[idx].owner == ctl)
 				control->vd[idx].owner = NULL;
 	up_write(&card->controls_rwsem);
+	snd_fasync_free(ctl->fasync);
 	snd_ctl_empty_read_queue(ctl);
 	put_pid(ctl->pid);
 	kfree(ctl);
@@ -181,7 +182,7 @@
 	_found:
 		wake_up(&ctl->change_sleep);
 		spin_unlock(&ctl->read_lock);
-		kill_fasync(&ctl->fasync, SIGIO, POLL_IN);
+		snd_kill_fasync(ctl->fasync, SIGIO, POLL_IN);
 	}
 	read_unlock_irqrestore(&card->ctl_files_rwlock, flags);
 }
@@ -1066,14 +1067,19 @@
 	const u32 pattern = 0xdeadbeef;
 	int ret;
 
+	down_read(&card->controls_rwsem);
 	kctl = snd_ctl_find_id(card, &control->id);
-	if (kctl == NULL)
-		return -ENOENT;
+	if (kctl == NULL) {
+		ret = -ENOENT;
+		goto unlock;
+	}
 
 	index_offset = snd_ctl_get_ioff(kctl, &control->id);
 	vd = &kctl->vd[index_offset];
-	if (!(vd->access & SNDRV_CTL_ELEM_ACCESS_READ) || kctl->get == NULL)
-		return -EPERM;
+	if (!(vd->access & SNDRV_CTL_ELEM_ACCESS_READ) || kctl->get == NULL) {
+		ret = -EPERM;
+		goto unlock;
+	}
 
 	snd_ctl_build_ioff(&control->id, kctl, index_offset);
 
@@ -1083,7 +1089,7 @@
 	info.id = control->id;
 	ret = __snd_ctl_elem_info(card, kctl, &info, NULL);
 	if (ret < 0)
-		return ret;
+		goto unlock;
 #endif
 
 	if (!snd_ctl_skip_validation(&info))
@@ -1093,7 +1099,7 @@
 		ret = kctl->get(kctl, control);
 	snd_power_unref(card);
 	if (ret < 0)
-		return ret;
+		goto unlock;
 	if (!snd_ctl_skip_validation(&info) &&
 	    sanity_check_elem_value(card, control, &info, pattern) < 0) {
 		dev_err(card->dev,
@@ -1101,8 +1107,11 @@
 			control->id.iface, control->id.device,
 			control->id.subdevice, control->id.name,
 			control->id.index);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto unlock;
 	}
+unlock:
+	up_read(&card->controls_rwsem);
 	return ret;
 }
 
@@ -1116,9 +1125,7 @@
 	if (IS_ERR(control))
 		return PTR_ERR(control);
 
-	down_read(&card->controls_rwsem);
 	result = snd_ctl_elem_read(card, control);
-	up_read(&card->controls_rwsem);
 	if (result < 0)
 		goto error;
 
@@ -2002,7 +2009,7 @@
 	struct snd_ctl_file *ctl;
 
 	ctl = file->private_data;
-	return fasync_helper(fd, file, on, &ctl->fasync);
+	return snd_fasync_helper(fd, file, on, &ctl->fasync);
 }
 
 /* return the preferred subdevice number if already assigned;
@@ -2170,7 +2177,7 @@
 	read_lock_irqsave(&card->ctl_files_rwlock, flags);
 	list_for_each_entry(ctl, &card->ctl_files, list) {
 		wake_up(&ctl->change_sleep);
-		kill_fasync(&ctl->fasync, SIGIO, POLL_ERR);
+		snd_kill_fasync(ctl->fasync, SIGIO, POLL_ERR);
 	}
 	read_unlock_irqrestore(&card->ctl_files_rwlock, flags);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/control_compat.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/control_compat.c
@@ -264,6 +264,7 @@
 				  struct snd_ctl_elem_value *data,
 				  int type, int count)
 {
+	struct snd_ctl_elem_value32 __user *data32 = userdata;
 	int i, size;
 
 	if (type == SNDRV_CTL_ELEM_TYPE_BOOLEAN ||
@@ -280,6 +281,8 @@
 		if (copy_to_user(valuep, data->value.bytes.data, size))
 			return -EFAULT;
 	}
+	if (copy_to_user(&data32->id, &data->id, sizeof(data32->id)))
+		return -EFAULT;
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/control_led.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/control_led.c
@@ -530,12 +530,11 @@
 			  bool attach)
 {
 	char buf2[256], *s, *os;
-	size_t len = max(sizeof(s) - 1, count);
 	struct snd_ctl_elem_id id;
 	int err;
 
-	strncpy(buf2, buf, len);
-	buf2[len] = '\0';
+	if (strscpy(buf2, buf, sizeof(buf2)) < 0)
+		return -E2BIG;
 	memset(&id, 0, sizeof(id));
 	id.iface = SNDRV_CTL_ELEM_IFACE_MIXER;
 	s = buf2;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/info.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/info.c
@@ -56,7 +56,7 @@
 };
 
 static int snd_info_version_init(void);
-static void snd_info_disconnect(struct snd_info_entry *entry);
+static void snd_info_clear_entries(struct snd_info_entry *entry);
 
 /*
 
@@ -111,9 +111,9 @@
 	entry = data->entry;
 	mutex_lock(&entry->access);
 	if (entry->c.ops->llseek) {
-		offset = entry->c.ops->llseek(entry,
-					      data->file_private_data,
-					      file, offset, orig);
+		ret = entry->c.ops->llseek(entry,
+					   data->file_private_data,
+					   file, offset, orig);
 		goto out;
 	}
 
@@ -569,11 +569,16 @@
 {
 	if (!card)
 		return;
-	mutex_lock(&info_mutex);
+
 	proc_remove(card->proc_root_link);
-	card->proc_root_link = NULL;
 	if (card->proc_root)
-		snd_info_disconnect(card->proc_root);
+		proc_remove(card->proc_root->p);
+
+	mutex_lock(&info_mutex);
+	if (card->proc_root)
+		snd_info_clear_entries(card->proc_root);
+	card->proc_root_link = NULL;
+	card->proc_root = NULL;
 	mutex_unlock(&info_mutex);
 }
 
@@ -745,15 +750,14 @@
 }
 EXPORT_SYMBOL(snd_info_create_card_entry);
 
-static void snd_info_disconnect(struct snd_info_entry *entry)
+static void snd_info_clear_entries(struct snd_info_entry *entry)
 {
 	struct snd_info_entry *p;
 
 	if (!entry->p)
 		return;
 	list_for_each_entry(p, &entry->children, list)
-		snd_info_disconnect(p);
-	proc_remove(entry->p);
+		snd_info_clear_entries(p);
 	entry->p = NULL;
 }
 
@@ -770,8 +774,9 @@
 	if (!entry)
 		return;
 	if (entry->p) {
+		proc_remove(entry->p);
 		mutex_lock(&info_mutex);
-		snd_info_disconnect(entry);
+		snd_info_clear_entries(entry);
 		mutex_unlock(&info_mutex);
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/init.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/init.c
@@ -178,10 +178,8 @@
 		return -ENOMEM;
 
 	err = snd_card_init(card, parent, idx, xid, module, extra_size);
-	if (err < 0) {
-		kfree(card);
-		return err;
-	}
+	if (err < 0)
+		return err; /* card is freed by error handler */
 
 	*card_ret = card;
 	return 0;
@@ -209,6 +207,12 @@
  * snd_card_register(), the very first devres action to call snd_card_free()
  * is added automatically.  In that way, the resource disconnection is assured
  * at first, then released in the expected order.
+ *
+ * If an error happens at the probe before snd_card_register() is called and
+ * there have been other devres resources, you'd need to free the card manually
+ * via snd_card_free() call in the error; otherwise it may lead to UAF due to
+ * devres call orders.  You can use snd_card_free_on_error() helper for
+ * handling it more easily.
  */
 int snd_devm_card_new(struct device *parent, int idx, const char *xid,
 		      struct module *module, size_t extra_size,
@@ -225,7 +229,7 @@
 	card->managed = true;
 	err = snd_card_init(card, parent, idx, xid, module, extra_size);
 	if (err < 0) {
-		devres_free(card);
+		devres_free(card); /* in managed mode, we need to free manually */
 		return err;
 	}
 
@@ -235,6 +239,28 @@
 }
 EXPORT_SYMBOL_GPL(snd_devm_card_new);
 
+/**
+ * snd_card_free_on_error - a small helper for handling devm probe errors
+ * @dev: the managed device object
+ * @ret: the return code from the probe callback
+ *
+ * This function handles the explicit snd_card_free() call at the error from
+ * the probe callback.  It's just a small helper for simplifying the error
+ * handling with the managed devices.
+ */
+int snd_card_free_on_error(struct device *dev, int ret)
+{
+	struct snd_card *card;
+
+	if (!ret)
+		return 0;
+	card = devres_find(dev, __snd_card_release, NULL, NULL);
+	if (card)
+		snd_card_free(card);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(snd_card_free_on_error);
+
 static int snd_card_init(struct snd_card *card, struct device *parent,
 			 int idx, const char *xid, struct module *module,
 			 size_t extra_size)
@@ -265,6 +291,8 @@
 		mutex_unlock(&snd_card_mutex);
 		dev_err(parent, "cannot find the slot for index %d (range 0-%i), error: %d\n",
 			 idx, snd_ecards_limit - 1, err);
+		if (!card->managed)
+			kfree(card); /* manually free here, as no destructor called */
 		return err;
 	}
 	set_bit(idx, snd_cards_lock);		/* lock it */
@@ -275,8 +303,8 @@
 	card->number = idx;
 #ifdef MODULE
 	WARN_ON(!module);
-	card->module = module;
 #endif
+	card->module = module;
 	INIT_LIST_HEAD(&card->devices);
 	init_rwsem(&card->controls_rwsem);
 	rwlock_init(&card->ctl_files_rwlock);
@@ -480,6 +508,14 @@
 	}
 	spin_unlock(&card->files_lock);	
 
+#ifdef CONFIG_PM
+	/* wake up sleepers here before other callbacks for avoiding potential
+	 * deadlocks with other locks (e.g. in kctls);
+	 * then this notifies the shutdown and sleepers would abort immediately
+	 */
+	wake_up_all(&card->power_sleep);
+#endif
+
 	/* notify all connected devices about disconnection */
 	/* at this point, they cannot respond to any calls except release() */
 
@@ -507,7 +543,6 @@
 	mutex_unlock(&snd_card_mutex);
 
 #ifdef CONFIG_PM
-	wake_up(&card->power_sleep);
 	snd_power_sync_ref(card);
 #endif
 	return 0;	
@@ -625,13 +660,19 @@
 }
 EXPORT_SYMBOL(snd_card_free);
 
+/* check, if the character is in the valid ASCII range */
+static inline bool safe_ascii_char(char c)
+{
+	return isascii(c) && isalnum(c);
+}
+
 /* retrieve the last word of shortname or longname */
 static const char *retrieve_id_from_card_name(const char *name)
 {
 	const char *spos = name;
 
 	while (*name) {
-		if (isspace(*name) && isalnum(name[1]))
+		if (isspace(*name) && safe_ascii_char(name[1]))
 			spos = name + 1;
 		name++;
 	}
@@ -658,12 +699,12 @@
 {
 	char *id = card->id;
 
-	while (*nid && !isalnum(*nid))
+	while (*nid && !safe_ascii_char(*nid))
 		nid++;
 	if (isdigit(*nid))
 		*id++ = isalpha(*src) ? *src : 'D';
 	while (*nid && (size_t)(id - card->id) < sizeof(card->id) - 1) {
-		if (isalnum(*nid))
+		if (safe_ascii_char(*nid))
 			*id++ = *nid;
 		nid++;
 	}
@@ -759,7 +800,7 @@
 
 	for (idx = 0; idx < copy; idx++) {
 		c = buf[idx];
-		if (!isalnum(c) && c != '_' && c != '-')
+		if (!safe_ascii_char(c) && c != '_' && c != '-')
 			return -EINVAL;
 	}
 	memcpy(buf1, buf, copy);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/jack.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/jack.c
@@ -42,8 +42,11 @@
 #ifdef CONFIG_SND_JACK_INPUT_DEV
 	struct snd_jack *jack = device->device_data;
 
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return 0;
+	}
 
 	/* If the input device is registered with the input subsystem
 	 * then we need to use a different deallocator. */
@@ -52,6 +55,7 @@
 	else
 		input_free_device(jack->input_dev);
 	jack->input_dev = NULL;
+	mutex_unlock(&jack->input_dev_lock);
 #endif /* CONFIG_SND_JACK_INPUT_DEV */
 	return 0;
 }
@@ -62,10 +66,13 @@
 	struct snd_card *card = device->card;
 	struct snd_jack_kctl *jack_kctl, *tmp_jack_kctl;
 
+	down_write(&card->controls_rwsem);
 	list_for_each_entry_safe(jack_kctl, tmp_jack_kctl, &jack->kctl_list, list) {
 		list_del_init(&jack_kctl->list);
 		snd_ctl_remove(card, jack_kctl->kctl);
 	}
+	up_write(&card->controls_rwsem);
+
 	if (jack->private_free)
 		jack->private_free(jack);
 
@@ -87,8 +94,11 @@
 	snprintf(jack->name, sizeof(jack->name), "%s %s",
 		 card->shortname, jack->id);
 
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return 0;
+	}
 
 	jack->input_dev->name = jack->name;
 
@@ -113,6 +123,7 @@
 	if (err == 0)
 		jack->registered = 1;
 
+	mutex_unlock(&jack->input_dev_lock);
 	return err;
 }
 #endif /* CONFIG_SND_JACK_INPUT_DEV */
@@ -509,10 +520,16 @@
 		return -ENOMEM;
 
 	jack->id = kstrdup(id, GFP_KERNEL);
+	if (jack->id == NULL) {
+		kfree(jack);
+		return -ENOMEM;
+	}
 
-	/* don't creat input device for phantom jack */
-	if (!phantom_jack) {
 #ifdef CONFIG_SND_JACK_INPUT_DEV
+	mutex_init(&jack->input_dev_lock);
+
+	/* don't create input device for phantom jack */
+	if (!phantom_jack) {
 		int i;
 
 		jack->input_dev = input_allocate_device();
@@ -530,8 +547,8 @@
 				input_set_capability(jack->input_dev, EV_SW,
 						     jack_switch_types[i]);
 
-#endif /* CONFIG_SND_JACK_INPUT_DEV */
 	}
+#endif /* CONFIG_SND_JACK_INPUT_DEV */
 
 	err = snd_device_new(card, SNDRV_DEV_JACK, jack, &ops);
 	if (err < 0)
@@ -571,10 +588,14 @@
 void snd_jack_set_parent(struct snd_jack *jack, struct device *parent)
 {
 	WARN_ON(jack->registered);
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return;
+	}
 
 	jack->input_dev->dev.parent = parent;
+	mutex_unlock(&jack->input_dev_lock);
 }
 EXPORT_SYMBOL(snd_jack_set_parent);
 
@@ -622,6 +643,8 @@
 
 /**
  * snd_jack_report - Report the current status of a jack
+ * Note: This function uses mutexes and should be called from a
+ * context which can sleep (such as a workqueue).
  *
  * @jack:   The jack to report status for
  * @status: The current status of the jack
@@ -631,6 +654,7 @@
 	struct snd_jack_kctl *jack_kctl;
 	unsigned int mask_bits = 0;
 #ifdef CONFIG_SND_JACK_INPUT_DEV
+	struct input_dev *idev;
 	int i;
 #endif
 
@@ -647,14 +671,15 @@
 					     status & jack_kctl->mask_bits);
 
 #ifdef CONFIG_SND_JACK_INPUT_DEV
-	if (!jack->input_dev)
+	idev = input_get_device(jack->input_dev);
+	if (!idev)
 		return;
 
 	for (i = 0; i < ARRAY_SIZE(jack->key); i++) {
 		int testbit = ((SND_JACK_BTN_0 >> i) & ~mask_bits);
 
 		if (jack->type & testbit)
-			input_report_key(jack->input_dev, jack->key[i],
+			input_report_key(idev, jack->key[i],
 					 status & testbit);
 	}
 
@@ -662,12 +687,13 @@
 		int testbit = ((1 << i) & ~mask_bits);
 
 		if (jack->type & testbit)
-			input_report_switch(jack->input_dev,
+			input_report_switch(idev,
 					    jack_switch_types[i],
 					    status & testbit);
 	}
 
-	input_sync(jack->input_dev);
+	input_sync(idev);
+	input_put_device(idev);
 #endif /* CONFIG_SND_JACK_INPUT_DEV */
 }
 EXPORT_SYMBOL(snd_jack_report);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/memalloc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/memalloc.c
@@ -176,8 +176,11 @@
 int snd_dma_buffer_mmap(struct snd_dma_buffer *dmab,
 			struct vm_area_struct *area)
 {
-	const struct snd_malloc_ops *ops = snd_dma_get_ops(dmab);
+	const struct snd_malloc_ops *ops;
 
+	if (!dmab)
+		return -ENOENT;
+	ops = snd_dma_get_ops(dmab);
 	if (ops && ops->mmap)
 		return ops->mmap(dmab, area);
 	else
@@ -491,6 +494,8 @@
 
 static const struct snd_malloc_ops *snd_dma_get_ops(struct snd_dma_buffer *dmab)
 {
+	if (WARN_ON_ONCE(!dmab))
+		return NULL;
 	if (WARN_ON_ONCE(dmab->dev.type <= SNDRV_DMA_TYPE_UNKNOWN ||
 			 dmab->dev.type >= ARRAY_SIZE(dma_ops)))
 		return NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/misc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/misc.c
@@ -10,6 +10,7 @@
 #include <linux/time.h>
 #include <linux/slab.h>
 #include <linux/ioport.h>
+#include <linux/fs.h>
 #include <sound/core.h>
 
 #ifdef CONFIG_SND_DEBUG
@@ -112,7 +113,7 @@
 {
 	const struct snd_pci_quirk *q;
 
-	for (q = list; q->subvendor; q++) {
+	for (q = list; q->subvendor || q->subdevice; q++) {
 		if (q->subvendor != vendor)
 			continue;
 		if (!q->subdevice ||
@@ -145,3 +146,96 @@
 }
 EXPORT_SYMBOL(snd_pci_quirk_lookup);
 #endif
+
+/*
+ * Deferred async signal helpers
+ *
+ * Below are a few helper functions to wrap the async signal handling
+ * in the deferred work.  The main purpose is to avoid the messy deadlock
+ * around tasklist_lock and co at the kill_fasync() invocation.
+ * fasync_helper() and kill_fasync() are replaced with snd_fasync_helper()
+ * and snd_kill_fasync(), respectively.  In addition, snd_fasync_free() has
+ * to be called at releasing the relevant file object.
+ */
+struct snd_fasync {
+	struct fasync_struct *fasync;
+	int signal;
+	int poll;
+	int on;
+	struct list_head list;
+};
+
+static DEFINE_SPINLOCK(snd_fasync_lock);
+static LIST_HEAD(snd_fasync_list);
+
+static void snd_fasync_work_fn(struct work_struct *work)
+{
+	struct snd_fasync *fasync;
+
+	spin_lock_irq(&snd_fasync_lock);
+	while (!list_empty(&snd_fasync_list)) {
+		fasync = list_first_entry(&snd_fasync_list, struct snd_fasync, list);
+		list_del_init(&fasync->list);
+		spin_unlock_irq(&snd_fasync_lock);
+		if (fasync->on)
+			kill_fasync(&fasync->fasync, fasync->signal, fasync->poll);
+		spin_lock_irq(&snd_fasync_lock);
+	}
+	spin_unlock_irq(&snd_fasync_lock);
+}
+
+static DECLARE_WORK(snd_fasync_work, snd_fasync_work_fn);
+
+int snd_fasync_helper(int fd, struct file *file, int on,
+		      struct snd_fasync **fasyncp)
+{
+	struct snd_fasync *fasync = NULL;
+
+	if (on) {
+		fasync = kzalloc(sizeof(*fasync), GFP_KERNEL);
+		if (!fasync)
+			return -ENOMEM;
+		INIT_LIST_HEAD(&fasync->list);
+	}
+
+	spin_lock_irq(&snd_fasync_lock);
+	if (*fasyncp) {
+		kfree(fasync);
+		fasync = *fasyncp;
+	} else {
+		if (!fasync) {
+			spin_unlock_irq(&snd_fasync_lock);
+			return 0;
+		}
+		*fasyncp = fasync;
+	}
+	fasync->on = on;
+	spin_unlock_irq(&snd_fasync_lock);
+	return fasync_helper(fd, file, on, &fasync->fasync);
+}
+EXPORT_SYMBOL_GPL(snd_fasync_helper);
+
+void snd_kill_fasync(struct snd_fasync *fasync, int signal, int poll)
+{
+	unsigned long flags;
+
+	if (!fasync || !fasync->on)
+		return;
+	spin_lock_irqsave(&snd_fasync_lock, flags);
+	fasync->signal = signal;
+	fasync->poll = poll;
+	list_move(&fasync->list, &snd_fasync_list);
+	schedule_work(&snd_fasync_work);
+	spin_unlock_irqrestore(&snd_fasync_lock, flags);
+}
+EXPORT_SYMBOL_GPL(snd_kill_fasync);
+
+void snd_fasync_free(struct snd_fasync *fasync)
+{
+	if (!fasync)
+		return;
+	fasync->on = 0;
+	flush_work(&snd_fasync_work);
+	kfree(fasync);
+}
+EXPORT_SYMBOL_GPL(snd_fasync_free);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/oss/mixer_oss.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/oss/mixer_oss.c
@@ -130,11 +130,13 @@
 
 	if (mixer == NULL)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	for (chn = 0; chn < 31; chn++) {
 		pslot = &mixer->slots[chn];
 		if (pslot->put_volume || pslot->put_recsrc)
 			result |= 1 << chn;
 	}
+	mutex_unlock(&mixer->reg_mutex);
 	return result;
 }
 
@@ -146,11 +148,13 @@
 
 	if (mixer == NULL)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	for (chn = 0; chn < 31; chn++) {
 		pslot = &mixer->slots[chn];
 		if (pslot->put_volume && pslot->stereo)
 			result |= 1 << chn;
 	}
+	mutex_unlock(&mixer->reg_mutex);
 	return result;
 }
 
@@ -161,6 +165,7 @@
 
 	if (mixer == NULL)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	if (mixer->put_recsrc && mixer->get_recsrc) {	/* exclusive */
 		result = mixer->mask_recsrc;
 	} else {
@@ -172,6 +177,7 @@
 				result |= 1 << chn;
 		}
 	}
+	mutex_unlock(&mixer->reg_mutex);
 	return result;
 }
 
@@ -182,12 +188,12 @@
 
 	if (mixer == NULL)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	if (mixer->put_recsrc && mixer->get_recsrc) {	/* exclusive */
-		int err;
 		unsigned int index;
-		err = mixer->get_recsrc(fmixer, &index);
-		if (err < 0)
-			return err;
+		result = mixer->get_recsrc(fmixer, &index);
+		if (result < 0)
+			goto unlock;
 		result = 1 << index;
 	} else {
 		struct snd_mixer_oss_slot *pslot;
@@ -202,7 +208,10 @@
 			}
 		}
 	}
-	return mixer->oss_recsrc = result;
+	mixer->oss_recsrc = result;
+ unlock:
+	mutex_unlock(&mixer->reg_mutex);
+	return result;
 }
 
 static int snd_mixer_oss_set_recsrc(struct snd_mixer_oss_file *fmixer, int recsrc)
@@ -215,6 +224,7 @@
 
 	if (mixer == NULL)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	if (mixer->get_recsrc && mixer->put_recsrc) {	/* exclusive input */
 		if (recsrc & ~mixer->oss_recsrc)
 			recsrc &= ~mixer->oss_recsrc;
@@ -240,6 +250,7 @@
 			}
 		}
 	}
+	mutex_unlock(&mixer->reg_mutex);
 	return result;
 }
 
@@ -251,6 +262,7 @@
 
 	if (mixer == NULL || slot > 30)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	pslot = &mixer->slots[slot];
 	left = pslot->volume[0];
 	right = pslot->volume[1];
@@ -258,15 +270,21 @@
 		result = pslot->get_volume(fmixer, pslot, &left, &right);
 	if (!pslot->stereo)
 		right = left;
-	if (snd_BUG_ON(left < 0 || left > 100))
-		return -EIO;
-	if (snd_BUG_ON(right < 0 || right > 100))
-		return -EIO;
+	if (snd_BUG_ON(left < 0 || left > 100)) {
+		result = -EIO;
+		goto unlock;
+	}
+	if (snd_BUG_ON(right < 0 || right > 100)) {
+		result = -EIO;
+		goto unlock;
+	}
 	if (result >= 0) {
 		pslot->volume[0] = left;
 		pslot->volume[1] = right;
 	 	result = (left & 0xff) | ((right & 0xff) << 8);
 	}
+ unlock:
+	mutex_unlock(&mixer->reg_mutex);
 	return result;
 }
 
@@ -279,6 +297,7 @@
 
 	if (mixer == NULL || slot > 30)
 		return -EIO;
+	mutex_lock(&mixer->reg_mutex);
 	pslot = &mixer->slots[slot];
 	if (left > 100)
 		left = 100;
@@ -289,10 +308,13 @@
 	if (pslot->put_volume)
 		result = pslot->put_volume(fmixer, pslot, left, right);
 	if (result < 0)
-		return result;
+		goto unlock;
 	pslot->volume[0] = left;
 	pslot->volume[1] = right;
- 	return (left & 0xff) | ((right & 0xff) << 8);
+	result = (left & 0xff) | ((right & 0xff) << 8);
+ unlock:
+	mutex_unlock(&mixer->reg_mutex);
+	return result;
 }
 
 static int snd_mixer_oss_ioctl1(struct snd_mixer_oss_file *fmixer, unsigned int cmd, unsigned long arg)
@@ -945,8 +967,8 @@
 	struct slot *p = chn->private_data;
 	if (p) {
 		if (p->allocated && p->assigned) {
-			kfree_const(p->assigned->name);
-			kfree_const(p->assigned);
+			kfree(p->assigned->name);
+			kfree(p->assigned);
 		}
 		kfree(p);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/oss/pcm_oss.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/oss/pcm_oss.c
@@ -147,7 +147,7 @@
  *
  * Return the maximum value for field PAR.
  */
-static unsigned int
+static int
 snd_pcm_hw_param_value_max(const struct snd_pcm_hw_params *params,
 			   snd_pcm_hw_param_t var, int *dir)
 {
@@ -682,18 +682,24 @@
 				   struct snd_pcm_hw_params *oss_params,
 				   struct snd_pcm_hw_params *slave_params)
 {
-	size_t s;
-	size_t oss_buffer_size, oss_period_size, oss_periods;
-	size_t min_period_size, max_period_size;
+	ssize_t s;
+	ssize_t oss_buffer_size;
+	ssize_t oss_period_size, oss_periods;
+	ssize_t min_period_size, max_period_size;
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	size_t oss_frame_size;
 
 	oss_frame_size = snd_pcm_format_physical_width(params_format(oss_params)) *
 			 params_channels(oss_params) / 8;
 
+	oss_buffer_size = snd_pcm_hw_param_value_max(slave_params,
+						     SNDRV_PCM_HW_PARAM_BUFFER_SIZE,
+						     NULL);
+	if (oss_buffer_size <= 0)
+		return -EINVAL;
 	oss_buffer_size = snd_pcm_plug_client_size(substream,
-						   snd_pcm_hw_param_value_max(slave_params, SNDRV_PCM_HW_PARAM_BUFFER_SIZE, NULL)) * oss_frame_size;
-	if (!oss_buffer_size)
+						   oss_buffer_size * oss_frame_size);
+	if (oss_buffer_size <= 0)
 		return -EINVAL;
 	oss_buffer_size = rounddown_pow_of_two(oss_buffer_size);
 	if (atomic_read(&substream->mmap_count)) {
@@ -730,7 +736,7 @@
 
 	min_period_size = snd_pcm_plug_client_size(substream,
 						   snd_pcm_hw_param_value_min(slave_params, SNDRV_PCM_HW_PARAM_PERIOD_SIZE, NULL));
-	if (min_period_size) {
+	if (min_period_size > 0) {
 		min_period_size *= oss_frame_size;
 		min_period_size = roundup_pow_of_two(min_period_size);
 		if (oss_period_size < min_period_size)
@@ -739,7 +745,7 @@
 
 	max_period_size = snd_pcm_plug_client_size(substream,
 						   snd_pcm_hw_param_value_max(slave_params, SNDRV_PCM_HW_PARAM_PERIOD_SIZE, NULL));
-	if (max_period_size) {
+	if (max_period_size > 0) {
 		max_period_size *= oss_frame_size;
 		max_period_size = rounddown_pow_of_two(max_period_size);
 		if (oss_period_size > max_period_size)
@@ -752,7 +758,7 @@
 		oss_periods = substream->oss.setup.periods;
 
 	s = snd_pcm_hw_param_value_max(slave_params, SNDRV_PCM_HW_PARAM_PERIODS, NULL);
-	if (runtime->oss.maxfrags && s > runtime->oss.maxfrags)
+	if (s > 0 && runtime->oss.maxfrags && s > runtime->oss.maxfrags)
 		s = runtime->oss.maxfrags;
 	if (oss_periods > s)
 		oss_periods = s;
@@ -768,6 +774,11 @@
 
 	if (oss_period_size < 16)
 		return -EINVAL;
+
+	/* don't allocate too large period; 1MB period must be enough */
+	if (oss_period_size > 1024 * 1024)
+		return -ENOMEM;
+
 	runtime->oss.period_bytes = oss_period_size;
 	runtime->oss.period_frames = 1;
 	runtime->oss.periods = oss_periods;
@@ -878,8 +889,15 @@
 		err = -EINVAL;
 		goto failure;
 	}
-	choose_rate(substream, sparams, runtime->oss.rate);
-	snd_pcm_hw_param_near(substream, sparams, SNDRV_PCM_HW_PARAM_CHANNELS, runtime->oss.channels, NULL);
+
+	err = choose_rate(substream, sparams, runtime->oss.rate);
+	if (err < 0)
+		goto failure;
+	err = snd_pcm_hw_param_near(substream, sparams,
+				    SNDRV_PCM_HW_PARAM_CHANNELS,
+				    runtime->oss.channels, NULL);
+	if (err < 0)
+		goto failure;
 
 	format = snd_pcm_oss_format_from(runtime->oss.format);
 
@@ -1030,10 +1048,9 @@
 			goto failure;
 	}
 #endif
-	oss_period_size *= oss_frame_size;
-
-	oss_buffer_size = oss_period_size * runtime->oss.periods;
-	if (oss_buffer_size < 0) {
+	oss_period_size = array_size(oss_period_size, oss_frame_size);
+	oss_buffer_size = array_size(oss_period_size, runtime->oss.periods);
+	if (oss_buffer_size <= 0) {
 		err = -EINVAL;
 		goto failure;
 	}
@@ -1212,12 +1229,12 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	int ret;
 	while (1) {
-		if (runtime->status->state == SNDRV_PCM_STATE_XRUN ||
-		    runtime->status->state == SNDRV_PCM_STATE_SUSPENDED) {
+		if (runtime->state == SNDRV_PCM_STATE_XRUN ||
+		    runtime->state == SNDRV_PCM_STATE_SUSPENDED) {
 #ifdef OSS_DEBUG
 			pcm_dbg(substream->pcm,
 				"pcm_oss: write: recovering from %s\n",
-				runtime->status->state == SNDRV_PCM_STATE_XRUN ?
+				runtime->state == SNDRV_PCM_STATE_XRUN ?
 				"XRUN" : "SUSPEND");
 #endif
 			ret = snd_pcm_oss_prepare(substream);
@@ -1232,7 +1249,7 @@
 			break;
 		/* test, if we can't store new data, because the stream */
 		/* has not been started */
-		if (runtime->status->state == SNDRV_PCM_STATE_PREPARED)
+		if (runtime->state == SNDRV_PCM_STATE_PREPARED)
 			return -EAGAIN;
 	}
 	return ret;
@@ -1244,18 +1261,18 @@
 	snd_pcm_sframes_t delay;
 	int ret;
 	while (1) {
-		if (runtime->status->state == SNDRV_PCM_STATE_XRUN ||
-		    runtime->status->state == SNDRV_PCM_STATE_SUSPENDED) {
+		if (runtime->state == SNDRV_PCM_STATE_XRUN ||
+		    runtime->state == SNDRV_PCM_STATE_SUSPENDED) {
 #ifdef OSS_DEBUG
 			pcm_dbg(substream->pcm,
 				"pcm_oss: read: recovering from %s\n",
-				runtime->status->state == SNDRV_PCM_STATE_XRUN ?
+				runtime->state == SNDRV_PCM_STATE_XRUN ?
 				"XRUN" : "SUSPEND");
 #endif
 			ret = snd_pcm_kernel_ioctl(substream, SNDRV_PCM_IOCTL_DRAIN, NULL);
 			if (ret < 0)
 				break;
-		} else if (runtime->status->state == SNDRV_PCM_STATE_SETUP) {
+		} else if (runtime->state == SNDRV_PCM_STATE_SETUP) {
 			ret = snd_pcm_oss_prepare(substream);
 			if (ret < 0)
 				break;
@@ -1268,7 +1285,7 @@
 					 frames, in_kernel);
 		mutex_lock(&runtime->oss.params_lock);
 		if (ret == -EPIPE) {
-			if (runtime->status->state == SNDRV_PCM_STATE_DRAINING) {
+			if (runtime->state == SNDRV_PCM_STATE_DRAINING) {
 				ret = snd_pcm_kernel_ioctl(substream, SNDRV_PCM_IOCTL_DROP, NULL);
 				if (ret < 0)
 					break;
@@ -1287,12 +1304,12 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	int ret;
 	while (1) {
-		if (runtime->status->state == SNDRV_PCM_STATE_XRUN ||
-		    runtime->status->state == SNDRV_PCM_STATE_SUSPENDED) {
+		if (runtime->state == SNDRV_PCM_STATE_XRUN ||
+		    runtime->state == SNDRV_PCM_STATE_SUSPENDED) {
 #ifdef OSS_DEBUG
 			pcm_dbg(substream->pcm,
 				"pcm_oss: writev: recovering from %s\n",
-				runtime->status->state == SNDRV_PCM_STATE_XRUN ?
+				runtime->state == SNDRV_PCM_STATE_XRUN ?
 				"XRUN" : "SUSPEND");
 #endif
 			ret = snd_pcm_oss_prepare(substream);
@@ -1305,7 +1322,7 @@
 
 		/* test, if we can't store new data, because the stream */
 		/* has not been started */
-		if (runtime->status->state == SNDRV_PCM_STATE_PREPARED)
+		if (runtime->state == SNDRV_PCM_STATE_PREPARED)
 			return -EAGAIN;
 	}
 	return ret;
@@ -1316,18 +1333,18 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	int ret;
 	while (1) {
-		if (runtime->status->state == SNDRV_PCM_STATE_XRUN ||
-		    runtime->status->state == SNDRV_PCM_STATE_SUSPENDED) {
+		if (runtime->state == SNDRV_PCM_STATE_XRUN ||
+		    runtime->state == SNDRV_PCM_STATE_SUSPENDED) {
 #ifdef OSS_DEBUG
 			pcm_dbg(substream->pcm,
 				"pcm_oss: readv: recovering from %s\n",
-				runtime->status->state == SNDRV_PCM_STATE_XRUN ?
+				runtime->state == SNDRV_PCM_STATE_XRUN ?
 				"XRUN" : "SUSPEND");
 #endif
 			ret = snd_pcm_kernel_ioctl(substream, SNDRV_PCM_IOCTL_DRAIN, NULL);
 			if (ret < 0)
 				break;
-		} else if (runtime->status->state == SNDRV_PCM_STATE_SETUP) {
+		} else if (runtime->state == SNDRV_PCM_STATE_SETUP) {
 			ret = snd_pcm_oss_prepare(substream);
 			if (ret < 0)
 				break;
@@ -1610,7 +1627,7 @@
 		result = 0;
 		set_current_state(TASK_INTERRUPTIBLE);
 		snd_pcm_stream_lock_irq(substream);
-		state = runtime->status->state;
+		state = runtime->state;
 		snd_pcm_stream_unlock_irq(substream);
 		if (state != SNDRV_PCM_STATE_RUNNING) {
 			set_current_state(TASK_RUNNING);
@@ -1647,14 +1664,14 @@
 		runtime = substream->runtime;
 		if (atomic_read(&substream->mmap_count))
 			goto __direct;
-		err = snd_pcm_oss_make_ready(substream);
-		if (err < 0)
-			return err;
 		atomic_inc(&runtime->oss.rw_ref);
 		if (mutex_lock_interruptible(&runtime->oss.params_lock)) {
 			atomic_dec(&runtime->oss.rw_ref);
 			return -ERESTARTSYS;
 		}
+		err = snd_pcm_oss_make_ready_locked(substream);
+		if (err < 0)
+			goto unlock;
 		format = snd_pcm_oss_format_from(runtime->oss.format);
 		width = snd_pcm_format_physical_width(format);
 		if (runtime->oss.buffer_used > 0) {
@@ -1956,7 +1973,7 @@
 	if (runtime->oss.subdivision || runtime->oss.fragshift)
 		return -EINVAL;
 	fragshift = val & 0xffff;
-	if (fragshift >= 31)
+	if (fragshift >= 25) /* should be large enough */
 		return -EINVAL;
 	runtime->oss.fragshift = fragshift;
 	runtime->oss.maxfrags = (val >> 16) & 0xffff;
@@ -2052,7 +2069,7 @@
 	int err, cmd;
 
 #ifdef OSS_DEBUG
-	pcm_dbg(substream->pcm, "pcm_oss: trigger = 0x%x\n", trigger);
+	pr_debug("pcm_oss: trigger = 0x%x\n", trigger);
 #endif
 	
 	psubstream = pcm_oss_file->streams[SNDRV_PCM_STREAM_PLAYBACK];
@@ -2835,8 +2852,8 @@
 		struct snd_pcm_runtime *runtime = psubstream->runtime;
 		poll_wait(file, &runtime->sleep, wait);
 		snd_pcm_stream_lock_irq(psubstream);
-		if (runtime->status->state != SNDRV_PCM_STATE_DRAINING &&
-		    (runtime->status->state != SNDRV_PCM_STATE_RUNNING ||
+		if (runtime->state != SNDRV_PCM_STATE_DRAINING &&
+		    (runtime->state != SNDRV_PCM_STATE_RUNNING ||
 		     snd_pcm_oss_playback_ready(psubstream)))
 			mask |= EPOLLOUT | EPOLLWRNORM;
 		snd_pcm_stream_unlock_irq(psubstream);
@@ -2846,7 +2863,7 @@
 		snd_pcm_state_t ostate;
 		poll_wait(file, &runtime->sleep, wait);
 		snd_pcm_stream_lock_irq(csubstream);
-		ostate = runtime->status->state;
+		ostate = runtime->state;
 		if (ostate != SNDRV_PCM_STATE_RUNNING ||
 		    snd_pcm_oss_capture_ready(csubstream))
 			mask |= EPOLLIN | EPOLLRDNORM;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/oss/pcm_plugin.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/oss/pcm_plugin.c
@@ -62,7 +62,10 @@
 	width = snd_pcm_format_physical_width(format->format);
 	if (width < 0)
 		return width;
-	size = frames * format->channels * width;
+	size = array3_size(frames, format->channels, width);
+	/* check for too large period size once again */
+	if (size > 1024 * 1024)
+		return -ENOMEM;
 	if (snd_BUG_ON(size % 8))
 		return -ENXIO;
 	size /= 8;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/oss/pcm_plugin.h
+++ linux-xilinx-zynqmp-5.15.0/sound/core/oss/pcm_plugin.h
@@ -141,6 +141,14 @@
 
 void *snd_pcm_plug_buf_alloc(struct snd_pcm_substream *plug, snd_pcm_uframes_t size);
 void snd_pcm_plug_buf_unlock(struct snd_pcm_substream *plug, void *ptr);
+#else
+
+static inline snd_pcm_sframes_t snd_pcm_plug_client_size(struct snd_pcm_substream *handle, snd_pcm_uframes_t drv_size) { return drv_size; }
+static inline snd_pcm_sframes_t snd_pcm_plug_slave_size(struct snd_pcm_substream *handle, snd_pcm_uframes_t clt_size) { return clt_size; }
+static inline int snd_pcm_plug_slave_format(int format, const struct snd_mask *format_mask) { return format; }
+
+#endif
+
 snd_pcm_sframes_t snd_pcm_oss_write3(struct snd_pcm_substream *substream,
 				     const char *ptr, snd_pcm_uframes_t size,
 				     int in_kernel);
@@ -151,14 +159,6 @@
 snd_pcm_sframes_t snd_pcm_oss_readv3(struct snd_pcm_substream *substream,
 				     void **bufs, snd_pcm_uframes_t frames);
 
-#else
-
-static inline snd_pcm_sframes_t snd_pcm_plug_client_size(struct snd_pcm_substream *handle, snd_pcm_uframes_t drv_size) { return drv_size; }
-static inline snd_pcm_sframes_t snd_pcm_plug_slave_size(struct snd_pcm_substream *handle, snd_pcm_uframes_t clt_size) { return clt_size; }
-static inline int snd_pcm_plug_slave_format(int format, const struct snd_mask *format_mask) { return format; }
-
-#endif
-
 #ifdef PLUGIN_DEBUG
 #define pdprintf(fmt, args...) printk(KERN_DEBUG "plugin: " fmt, ##args)
 #else
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm.c
@@ -251,6 +251,7 @@
 	STATE(DRAINING),
 	STATE(PAUSED),
 	STATE(SUSPENDED),
+	STATE(DISCONNECTED),
 };
 
 static const char * const snd_pcm_access_names[] = {
@@ -385,7 +386,7 @@
 		snd_iprintf(buffer, "closed\n");
 		goto unlock;
 	}
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN) {
+	if (runtime->state == SNDRV_PCM_STATE_OPEN) {
 		snd_iprintf(buffer, "no setup\n");
 		goto unlock;
 	}
@@ -422,7 +423,7 @@
 		snd_iprintf(buffer, "closed\n");
 		goto unlock;
 	}
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN) {
+	if (runtime->state == SNDRV_PCM_STATE_OPEN) {
 		snd_iprintf(buffer, "no setup\n");
 		goto unlock;
 	}
@@ -810,7 +811,11 @@
 static void free_chmap(struct snd_pcm_str *pstr)
 {
 	if (pstr->chmap_kctl) {
-		snd_ctl_remove(pstr->pcm->card, pstr->chmap_kctl);
+		struct snd_card *card = pstr->pcm->card;
+
+		down_write(&card->controls_rwsem);
+		snd_ctl_remove(card, pstr->chmap_kctl);
+		up_write(&card->controls_rwsem);
 		pstr->chmap_kctl = NULL;
 	}
 }
@@ -964,7 +969,9 @@
 	init_waitqueue_head(&runtime->sleep);
 	init_waitqueue_head(&runtime->tsleep);
 
-	runtime->status->state = SNDRV_PCM_STATE_OPEN;
+	__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_OPEN);
+	mutex_init(&runtime->buffer_mutex);
+	atomic_set(&runtime->buffer_accessing, 0);
 
 	substream->runtime = runtime;
 	substream->private_data = pcm->private_data;
@@ -998,6 +1005,7 @@
 	} else {
 		substream->runtime = NULL;
 	}
+	mutex_destroy(&runtime->buffer_mutex);
 	kfree(runtime);
 	put_pid(substream->pid);
 	substream->pid = NULL;
@@ -1102,7 +1110,8 @@
 			if (snd_pcm_running(substream))
 				snd_pcm_stop(substream, SNDRV_PCM_STATE_DISCONNECTED);
 			/* to be sure, set the state unconditionally */
-			substream->runtime->status->state = SNDRV_PCM_STATE_DISCONNECTED;
+			__snd_pcm_set_state(substream->runtime,
+					    SNDRV_PCM_STATE_DISCONNECTED);
 			wake_up(&substream->runtime->sleep);
 			wake_up(&substream->runtime->tsleep);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm_compat.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm_compat.c
@@ -253,10 +253,14 @@
 		goto error;
 	}
 
-	if (refine)
+	if (refine) {
 		err = snd_pcm_hw_refine(substream, data);
-	else
+		if (err < 0)
+			goto error;
+		err = fixup_unreferenced_params(substream, data);
+	} else {
 		err = snd_pcm_hw_params(substream, data);
+	}
 	if (err < 0)
 		goto error;
 	if (copy_to_user(data32, data, sizeof(*data32)) ||
@@ -295,7 +299,7 @@
 		return -ENOTTY;
 	if (substream->stream != dir)
 		return -EINVAL;
-	if (substream->runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (substream->runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 
 	if (get_user(buf, &data32->buf) ||
@@ -341,7 +345,7 @@
 		return -ENOTTY;
 	if (substream->stream != dir)
 		return -EINVAL;
-	if (substream->runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (substream->runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 
 	ch = substream->runtime->channels;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm_dmaengine.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm_dmaengine.c
@@ -132,12 +132,14 @@
 
 static void dmaengine_pcm_dma_complete(void *arg)
 {
+	unsigned int new_pos;
 	struct snd_pcm_substream *substream = arg;
 	struct dmaengine_pcm_runtime_data *prtd = substream_to_prtd(substream);
 
-	prtd->pos += snd_pcm_lib_period_bytes(substream);
-	if (prtd->pos >= snd_pcm_lib_buffer_bytes(substream))
-		prtd->pos = 0;
+	new_pos = prtd->pos + snd_pcm_lib_period_bytes(substream);
+	if (new_pos >= snd_pcm_lib_buffer_bytes(substream))
+		new_pos = 0;
+	prtd->pos = new_pos;
 
 	snd_pcm_period_elapsed(substream);
 }
@@ -342,6 +344,20 @@
 }
 EXPORT_SYMBOL_GPL(snd_dmaengine_pcm_open_request_chan);
 
+int snd_dmaengine_pcm_sync_stop(struct snd_pcm_substream *substream)
+{
+	struct dmaengine_pcm_runtime_data *prtd = substream_to_prtd(substream);
+	struct dma_tx_state state;
+	enum dma_status status;
+
+	status = dmaengine_tx_status(prtd->dma_chan, prtd->cookie, &state);
+	if (status != DMA_PAUSED)
+		dmaengine_synchronize(prtd->dma_chan);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(snd_dmaengine_pcm_sync_stop);
+
 /**
  * snd_dmaengine_pcm_close - Close a dmaengine based PCM substream
  * @substream: PCM substream
@@ -349,6 +365,12 @@
 int snd_dmaengine_pcm_close(struct snd_pcm_substream *substream)
 {
 	struct dmaengine_pcm_runtime_data *prtd = substream_to_prtd(substream);
+	struct dma_tx_state state;
+	enum dma_status status;
+
+	status = dmaengine_tx_status(prtd->dma_chan, prtd->cookie, &state);
+	if (status == DMA_PAUSED)
+		dmaengine_terminate_async(prtd->dma_chan);
 
 	dmaengine_synchronize(prtd->dma_chan);
 	kfree(prtd);
@@ -367,6 +389,12 @@
 int snd_dmaengine_pcm_close_release_chan(struct snd_pcm_substream *substream)
 {
 	struct dmaengine_pcm_runtime_data *prtd = substream_to_prtd(substream);
+	struct dma_tx_state state;
+	enum dma_status status;
+
+	status = dmaengine_tx_status(prtd->dma_chan, prtd->cookie, &state);
+	if (status == DMA_PAUSED)
+		dmaengine_terminate_async(prtd->dma_chan);
 
 	dmaengine_synchronize(prtd->dma_chan);
 	dma_release_channel(prtd->dma_chan);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm_lib.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm_lib.c
@@ -185,7 +185,7 @@
 	avail = snd_pcm_avail(substream);
 	if (avail > runtime->avail_max)
 		runtime->avail_max = avail;
-	if (runtime->status->state == SNDRV_PCM_STATE_DRAINING) {
+	if (runtime->state == SNDRV_PCM_STATE_DRAINING) {
 		if (avail >= runtime->buffer_size) {
 			snd_pcm_drain_done(substream);
 			return -EPIPE;
@@ -1910,7 +1910,7 @@
 
 		snd_pcm_stream_lock_irq(substream);
 		set_current_state(TASK_INTERRUPTIBLE);
-		switch (runtime->status->state) {
+		switch (runtime->state) {
 		case SNDRV_PCM_STATE_SUSPENDED:
 			err = -ESTRPIPE;
 			goto _endloop;
@@ -2098,14 +2098,14 @@
 	runtime = substream->runtime;
 	if (snd_BUG_ON(!substream->ops->copy_user && !runtime->dma_area))
 		return -EINVAL;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 	return 0;
 }
 
 static int pcm_accessible_state(struct snd_pcm_runtime *runtime)
 {
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_PREPARED:
 	case SNDRV_PCM_STATE_RUNNING:
 	case SNDRV_PCM_STATE_PAUSED:
@@ -2137,6 +2137,8 @@
 		ret = substream->ops->ack(substream);
 		if (ret < 0) {
 			runtime->control->appl_ptr = old_appl_ptr;
+			if (ret == -EPIPE)
+				__snd_pcm_xrun(substream);
 			return ret;
 		}
 	}
@@ -2207,7 +2209,7 @@
 		goto _end_unlock;
 
 	runtime->twake = runtime->control->avail_min ? : 1;
-	if (runtime->status->state == SNDRV_PCM_STATE_RUNNING)
+	if (runtime->state == SNDRV_PCM_STATE_RUNNING)
 		snd_pcm_update_hw_ptr(substream);
 
 	/*
@@ -2215,7 +2217,7 @@
 	 * thread may start capture
 	 */
 	if (!is_playback &&
-	    runtime->status->state == SNDRV_PCM_STATE_PREPARED &&
+	    runtime->state == SNDRV_PCM_STATE_PREPARED &&
 	    size >= runtime->start_threshold) {
 		err = snd_pcm_start(substream);
 		if (err < 0)
@@ -2229,7 +2231,7 @@
 		snd_pcm_uframes_t cont;
 		if (!avail) {
 			if (!is_playback &&
-			    runtime->status->state == SNDRV_PCM_STATE_DRAINING) {
+			    runtime->state == SNDRV_PCM_STATE_DRAINING) {
 				snd_pcm_stop(substream, SNDRV_PCM_STATE_SETUP);
 				goto _end_unlock;
 			}
@@ -2255,10 +2257,15 @@
 			err = -EINVAL;
 			goto _end_unlock;
 		}
+		if (!atomic_inc_unless_negative(&runtime->buffer_accessing)) {
+			err = -EBUSY;
+			goto _end_unlock;
+		}
 		snd_pcm_stream_unlock_irq(substream);
 		err = writer(substream, appl_ofs, data, offset, frames,
 			     transfer);
 		snd_pcm_stream_lock_irq(substream);
+		atomic_dec(&runtime->buffer_accessing);
 		if (err < 0)
 			goto _end_unlock;
 		err = pcm_accessible_state(runtime);
@@ -2276,7 +2283,7 @@
 		xfer += frames;
 		avail -= frames;
 		if (is_playback &&
-		    runtime->status->state == SNDRV_PCM_STATE_PREPARED &&
+		    runtime->state == SNDRV_PCM_STATE_PREPARED &&
 		    snd_pcm_playback_hw_avail(runtime) >= (snd_pcm_sframes_t)runtime->start_threshold) {
 			err = snd_pcm_start(substream);
 			if (err < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm_memory.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm_memory.c
@@ -31,20 +31,51 @@
 module_param(max_alloc_per_card, ulong, 0644);
 MODULE_PARM_DESC(max_alloc_per_card, "Max total allocation bytes per card.");
 
+static void __update_allocated_size(struct snd_card *card, ssize_t bytes)
+{
+	card->total_pcm_alloc_bytes += bytes;
+}
+
+static void update_allocated_size(struct snd_card *card, ssize_t bytes)
+{
+	mutex_lock(&card->memory_mutex);
+	__update_allocated_size(card, bytes);
+	mutex_unlock(&card->memory_mutex);
+}
+
+static void decrease_allocated_size(struct snd_card *card, size_t bytes)
+{
+	mutex_lock(&card->memory_mutex);
+	WARN_ON(card->total_pcm_alloc_bytes < bytes);
+	__update_allocated_size(card, -(ssize_t)bytes);
+	mutex_unlock(&card->memory_mutex);
+}
+
 static int do_alloc_pages(struct snd_card *card, int type, struct device *dev,
 			  size_t size, struct snd_dma_buffer *dmab)
 {
 	int err;
 
+	/* check and reserve the requested size */
+	mutex_lock(&card->memory_mutex);
 	if (max_alloc_per_card &&
-	    card->total_pcm_alloc_bytes + size > max_alloc_per_card)
+	    card->total_pcm_alloc_bytes + size > max_alloc_per_card) {
+		mutex_unlock(&card->memory_mutex);
 		return -ENOMEM;
+	}
+	__update_allocated_size(card, size);
+	mutex_unlock(&card->memory_mutex);
 
 	err = snd_dma_alloc_pages(type, dev, size, dmab);
 	if (!err) {
-		mutex_lock(&card->memory_mutex);
-		card->total_pcm_alloc_bytes += dmab->bytes;
-		mutex_unlock(&card->memory_mutex);
+		/* the actual allocation size might be bigger than requested,
+		 * and we need to correct the account
+		 */
+		if (dmab->bytes != size)
+			update_allocated_size(card, dmab->bytes - size);
+	} else {
+		/* take back on allocation failure */
+		decrease_allocated_size(card, size);
 	}
 	return err;
 }
@@ -53,10 +84,7 @@
 {
 	if (!dmab->area)
 		return;
-	mutex_lock(&card->memory_mutex);
-	WARN_ON(card->total_pcm_alloc_bytes < dmab->bytes);
-	card->total_pcm_alloc_bytes -= dmab->bytes;
-	mutex_unlock(&card->memory_mutex);
+	decrease_allocated_size(card, dmab->bytes);
 	snd_dma_free_pages(dmab);
 	dmab->area = NULL;
 }
@@ -158,19 +186,20 @@
 	size_t size;
 	struct snd_dma_buffer new_dmab;
 
+	mutex_lock(&substream->pcm->open_mutex);
 	if (substream->runtime) {
 		buffer->error = -EBUSY;
-		return;
+		goto unlock;
 	}
 	if (!snd_info_get_line(buffer, line, sizeof(line))) {
 		snd_info_get_str(str, line, sizeof(str));
 		size = simple_strtoul(str, NULL, 10) * 1024;
 		if ((size != 0 && size < 8192) || size > substream->dma_max) {
 			buffer->error = -EINVAL;
-			return;
+			goto unlock;
 		}
 		if (substream->dma_buffer.bytes == size)
-			return;
+			goto unlock;
 		memset(&new_dmab, 0, sizeof(new_dmab));
 		new_dmab.dev = substream->dma_buffer.dev;
 		if (size > 0) {
@@ -183,7 +212,7 @@
 					 substream->pcm->card->number, substream->pcm->device,
 					 substream->stream ? 'c' : 'p', substream->number,
 					 substream->pcm->name, size);
-				return;
+				goto unlock;
 			}
 			substream->buffer_bytes_max = size;
 		} else {
@@ -195,6 +224,8 @@
 	} else {
 		buffer->error = -EINVAL;
 	}
+ unlock:
+	mutex_unlock(&substream->pcm->open_mutex);
 }
 
 static inline void preallocate_info_init(struct snd_pcm_substream *substream)
@@ -443,7 +474,6 @@
  */
 int snd_pcm_lib_free_pages(struct snd_pcm_substream *substream)
 {
-	struct snd_card *card = substream->pcm->card;
 	struct snd_pcm_runtime *runtime;
 
 	if (PCM_RUNTIME_CHECK(substream))
@@ -452,6 +482,8 @@
 	if (runtime->dma_area == NULL)
 		return 0;
 	if (runtime->dma_buffer_p != &substream->dma_buffer) {
+		struct snd_card *card = substream->pcm->card;
+
 		/* it's a newly allocated buffer.  release it now. */
 		do_free_pages(card, runtime->dma_buffer_p);
 		kfree(runtime->dma_buffer_p);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm_misc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm_misc.c
@@ -433,7 +433,7 @@
 		return 0;
 	width = pcm_formats[(INT)format].phys; /* physical width */
 	pat = pcm_formats[(INT)format].silence;
-	if (! width)
+	if (!width || !pat)
 		return -EINVAL;
 	/* signed or 1 byte data */
 	if (pcm_formats[(INT)format].signd == 1 || width <= 8) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/pcm_native.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/pcm_native.c
@@ -172,6 +172,19 @@
 }
 EXPORT_SYMBOL_GPL(_snd_pcm_stream_lock_irqsave);
 
+unsigned long _snd_pcm_stream_lock_irqsave_nested(struct snd_pcm_substream *substream)
+{
+	unsigned long flags = 0;
+	if (substream->pcm->nonatomic)
+		mutex_lock_nested(&substream->self_group.mutex,
+				  SINGLE_DEPTH_NESTING);
+	else
+		spin_lock_irqsave_nested(&substream->self_group.lock, flags,
+					 SINGLE_DEPTH_NESTING);
+	return flags;
+}
+EXPORT_SYMBOL_GPL(_snd_pcm_stream_lock_irqsave_nested);
+
 /**
  * snd_pcm_stream_unlock_irqrestore - Unlock the PCM stream
  * @substream: PCM substream
@@ -582,8 +595,8 @@
 			      snd_pcm_state_t state)
 {
 	snd_pcm_stream_lock_irq(substream);
-	if (substream->runtime->status->state != SNDRV_PCM_STATE_DISCONNECTED)
-		substream->runtime->status->state = state;
+	if (substream->runtime->state != SNDRV_PCM_STATE_DISCONNECTED)
+		__snd_pcm_set_state(substream->runtime, state);
 	snd_pcm_stream_unlock_irq(substream);
 }
 
@@ -672,6 +685,30 @@
 	return 0;
 }
 
+/* acquire buffer_mutex; if it's in r/w operation, return -EBUSY, otherwise
+ * block the further r/w operations
+ */
+static int snd_pcm_buffer_access_lock(struct snd_pcm_runtime *runtime)
+{
+	if (!atomic_dec_unless_positive(&runtime->buffer_accessing))
+		return -EBUSY;
+	mutex_lock(&runtime->buffer_mutex);
+	return 0; /* keep buffer_mutex, unlocked by below */
+}
+
+/* release buffer_mutex and clear r/w access flag */
+static void snd_pcm_buffer_access_unlock(struct snd_pcm_runtime *runtime)
+{
+	mutex_unlock(&runtime->buffer_mutex);
+	atomic_inc(&runtime->buffer_accessing);
+}
+
+#if IS_ENABLED(CONFIG_SND_PCM_OSS)
+#define is_oss_stream(substream)	((substream)->oss.oss)
+#else
+#define is_oss_stream(substream)	false
+#endif
+
 static int snd_pcm_hw_params(struct snd_pcm_substream *substream,
 			     struct snd_pcm_hw_params *params)
 {
@@ -683,22 +720,25 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
+	err = snd_pcm_buffer_access_lock(runtime);
+	if (err < 0)
+		return err;
 	snd_pcm_stream_lock_irq(substream);
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_OPEN:
 	case SNDRV_PCM_STATE_SETUP:
 	case SNDRV_PCM_STATE_PREPARED:
+		if (!is_oss_stream(substream) &&
+		    atomic_read(&substream->mmap_count))
+			err = -EBADFD;
 		break;
 	default:
-		snd_pcm_stream_unlock_irq(substream);
-		return -EBADFD;
+		err = -EBADFD;
+		break;
 	}
 	snd_pcm_stream_unlock_irq(substream);
-#if IS_ENABLED(CONFIG_SND_PCM_OSS)
-	if (!substream->oss.oss)
-#endif
-		if (atomic_read(&substream->mmap_count))
-			return -EBADFD;
+	if (err)
+		goto unlock;
 
 	snd_pcm_sync_stop(substream, true);
 
@@ -786,16 +826,21 @@
 	if (usecs >= 0)
 		cpu_latency_qos_add_request(&substream->latency_pm_qos_req,
 					    usecs);
-	return 0;
+	err = 0;
  _error:
-	/* hardware might be unusable from this time,
-	   so we force application to retry to set
-	   the correct hardware parameter settings */
-	snd_pcm_set_state(substream, SNDRV_PCM_STATE_OPEN);
-	if (substream->ops->hw_free != NULL)
-		substream->ops->hw_free(substream);
-	if (substream->managed_buffer_alloc)
-		snd_pcm_lib_free_pages(substream);
+	if (err) {
+		/* hardware might be unusable from this time,
+		 * so we force application to retry to set
+		 * the correct hardware parameter settings
+		 */
+		snd_pcm_set_state(substream, SNDRV_PCM_STATE_OPEN);
+		if (substream->ops->hw_free != NULL)
+			substream->ops->hw_free(substream);
+		if (substream->managed_buffer_alloc)
+			snd_pcm_lib_free_pages(substream);
+	}
+ unlock:
+	snd_pcm_buffer_access_unlock(runtime);
 	return err;
 }
 
@@ -835,26 +880,33 @@
 static int snd_pcm_hw_free(struct snd_pcm_substream *substream)
 {
 	struct snd_pcm_runtime *runtime;
-	int result;
+	int result = 0;
 
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
+	result = snd_pcm_buffer_access_lock(runtime);
+	if (result < 0)
+		return result;
 	snd_pcm_stream_lock_irq(substream);
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_SETUP:
 	case SNDRV_PCM_STATE_PREPARED:
+		if (atomic_read(&substream->mmap_count))
+			result = -EBADFD;
 		break;
 	default:
-		snd_pcm_stream_unlock_irq(substream);
-		return -EBADFD;
+		result = -EBADFD;
+		break;
 	}
 	snd_pcm_stream_unlock_irq(substream);
-	if (atomic_read(&substream->mmap_count))
-		return -EBADFD;
+	if (result)
+		goto unlock;
 	result = do_hw_free(substream);
 	snd_pcm_set_state(substream, SNDRV_PCM_STATE_OPEN);
 	cpu_latency_qos_remove_request(&substream->latency_pm_qos_req);
+ unlock:
+	snd_pcm_buffer_access_unlock(runtime);
 	return result;
 }
 
@@ -868,7 +920,7 @@
 		return -ENXIO;
 	runtime = substream->runtime;
 	snd_pcm_stream_lock_irq(substream);
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN) {
+	if (runtime->state == SNDRV_PCM_STATE_OPEN) {
 		snd_pcm_stream_unlock_irq(substream);
 		return -EBADFD;
 	}
@@ -961,8 +1013,8 @@
 	} else
 		runtime->audio_tstamp_report.valid = 1;
 
-	status->state = runtime->status->state;
-	status->suspended_state = runtime->status->suspended_state;
+	status->state = runtime->state;
+	status->suspended_state = runtime->suspended_state;
 	if (status->state == SNDRV_PCM_STATE_OPEN)
 		goto _end;
 	status->trigger_tstamp_sec = runtime->trigger_tstamp.tv_sec;
@@ -1096,7 +1148,7 @@
 	channel = info->channel;
 	runtime = substream->runtime;
 	snd_pcm_stream_lock_irq(substream);
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN) {
+	if (runtime->state == SNDRV_PCM_STATE_OPEN) {
 		snd_pcm_stream_unlock_irq(substream);
 		return -EBADFD;
 	}
@@ -1160,15 +1212,17 @@
 static int snd_pcm_action_group(const struct action_ops *ops,
 				struct snd_pcm_substream *substream,
 				snd_pcm_state_t state,
-				bool do_lock)
+				bool stream_lock)
 {
 	struct snd_pcm_substream *s = NULL;
 	struct snd_pcm_substream *s1;
 	int res = 0, depth = 1;
 
 	snd_pcm_group_for_each_entry(s, substream) {
-		if (do_lock && s != substream) {
-			if (s->pcm->nonatomic)
+		if (s != substream) {
+			if (!stream_lock)
+				mutex_lock_nested(&s->runtime->buffer_mutex, depth);
+			else if (s->pcm->nonatomic)
 				mutex_lock_nested(&s->self_group.mutex, depth);
 			else
 				spin_lock_nested(&s->self_group.lock, depth);
@@ -1196,18 +1250,18 @@
 		ops->post_action(s, state);
 	}
  _unlock:
-	if (do_lock) {
-		/* unlock streams */
-		snd_pcm_group_for_each_entry(s1, substream) {
-			if (s1 != substream) {
-				if (s1->pcm->nonatomic)
-					mutex_unlock(&s1->self_group.mutex);
-				else
-					spin_unlock(&s1->self_group.lock);
-			}
-			if (s1 == s)	/* end */
-				break;
+	/* unlock streams */
+	snd_pcm_group_for_each_entry(s1, substream) {
+		if (s1 != substream) {
+			if (!stream_lock)
+				mutex_unlock(&s1->runtime->buffer_mutex);
+			else if (s1->pcm->nonatomic)
+				mutex_unlock(&s1->self_group.mutex);
+			else
+				spin_unlock(&s1->self_group.lock);
 		}
+		if (s1 == s)	/* end */
+			break;
 	}
 	return res;
 }
@@ -1337,10 +1391,15 @@
 
 	/* Guarantee the group members won't change during non-atomic action */
 	down_read(&snd_pcm_link_rwsem);
+	res = snd_pcm_buffer_access_lock(substream->runtime);
+	if (res < 0)
+		goto unlock;
 	if (snd_pcm_stream_linked(substream))
 		res = snd_pcm_action_group(ops, substream, state, false);
 	else
 		res = snd_pcm_action_single(ops, substream, state);
+	snd_pcm_buffer_access_unlock(substream->runtime);
+ unlock:
 	up_read(&snd_pcm_link_rwsem);
 	return res;
 }
@@ -1352,7 +1411,7 @@
 			     snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	if (runtime->status->state != SNDRV_PCM_STATE_PREPARED)
+	if (runtime->state != SNDRV_PCM_STATE_PREPARED)
 		return -EBADFD;
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
 	    !snd_pcm_playback_data(substream))
@@ -1373,8 +1432,10 @@
 static void snd_pcm_undo_start(struct snd_pcm_substream *substream,
 			       snd_pcm_state_t state)
 {
-	if (substream->runtime->trigger_master == substream)
+	if (substream->runtime->trigger_master == substream) {
 		substream->ops->trigger(substream, SNDRV_PCM_TRIGGER_STOP);
+		substream->runtime->stop_operating = true;
+	}
 }
 
 static void snd_pcm_post_start(struct snd_pcm_substream *substream,
@@ -1385,7 +1446,7 @@
 	runtime->hw_ptr_jiffies = jiffies;
 	runtime->hw_ptr_buffer_jiffies = (runtime->buffer_size * HZ) / 
 							    runtime->rate;
-	runtime->status->state = state;
+	__snd_pcm_set_state(runtime, state);
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
 	    runtime->silence_size > 0)
 		snd_pcm_playback_silence(substream, ULONG_MAX);
@@ -1426,7 +1487,7 @@
 			    snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 	runtime->trigger_master = substream;
 	return 0;
@@ -1447,9 +1508,9 @@
 			      snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	if (runtime->status->state != state) {
+	if (runtime->state != state) {
 		snd_pcm_trigger_tstamp(substream);
-		runtime->status->state = state;
+		__snd_pcm_set_state(runtime, state);
 		snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MSTOP);
 	}
 	wake_up(&runtime->sleep);
@@ -1525,9 +1586,9 @@
 	if (!(runtime->info & SNDRV_PCM_INFO_PAUSE))
 		return -ENOSYS;
 	if (pause_pushed(state)) {
-		if (runtime->status->state != SNDRV_PCM_STATE_RUNNING)
+		if (runtime->state != SNDRV_PCM_STATE_RUNNING)
 			return -EBADFD;
-	} else if (runtime->status->state != SNDRV_PCM_STATE_PAUSED)
+	} else if (runtime->state != SNDRV_PCM_STATE_PAUSED)
 		return -EBADFD;
 	runtime->trigger_master = substream;
 	return 0;
@@ -1569,12 +1630,12 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	snd_pcm_trigger_tstamp(substream);
 	if (pause_pushed(state)) {
-		runtime->status->state = SNDRV_PCM_STATE_PAUSED;
+		__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_PAUSED);
 		snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MPAUSE);
 		wake_up(&runtime->sleep);
 		wake_up(&runtime->tsleep);
 	} else {
-		runtime->status->state = SNDRV_PCM_STATE_RUNNING;
+		__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_RUNNING);
 		snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MCONTINUE);
 	}
 }
@@ -1609,7 +1670,7 @@
 			       snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_SUSPENDED:
 		return -EBUSY;
 	/* unresumable PCM state; return -EBUSY for skipping suspend */
@@ -1640,8 +1701,9 @@
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	snd_pcm_trigger_tstamp(substream);
-	runtime->status->suspended_state = runtime->status->state;
-	runtime->status->state = SNDRV_PCM_STATE_SUSPENDED;
+	runtime->suspended_state = runtime->state;
+	runtime->status->suspended_state = runtime->suspended_state;
+	__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_SUSPENDED);
 	snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MSUSPEND);
 	wake_up(&runtime->sleep);
 	wake_up(&runtime->tsleep);
@@ -1732,8 +1794,8 @@
 	if (runtime->trigger_master != substream)
 		return 0;
 	/* DMA not running previously? */
-	if (runtime->status->suspended_state != SNDRV_PCM_STATE_RUNNING &&
-	    (runtime->status->suspended_state != SNDRV_PCM_STATE_DRAINING ||
+	if (runtime->suspended_state != SNDRV_PCM_STATE_RUNNING &&
+	    (runtime->suspended_state != SNDRV_PCM_STATE_DRAINING ||
 	     substream->stream != SNDRV_PCM_STREAM_PLAYBACK))
 		return 0;
 	return substream->ops->trigger(substream, SNDRV_PCM_TRIGGER_RESUME);
@@ -1752,7 +1814,7 @@
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	snd_pcm_trigger_tstamp(substream);
-	runtime->status->state = runtime->status->suspended_state;
+	__snd_pcm_set_state(runtime, runtime->suspended_state);
 	snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MRESUME);
 }
 
@@ -1789,7 +1851,7 @@
 	int result;
 
 	snd_pcm_stream_lock_irq(substream);
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_XRUN:
 		result = 0;	/* already there */
 		break;
@@ -1812,7 +1874,7 @@
 			     snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_RUNNING:
 	case SNDRV_PCM_STATE_PREPARED:
 	case SNDRV_PCM_STATE_PAUSED:
@@ -1830,11 +1892,13 @@
 	int err = snd_pcm_ops_ioctl(substream, SNDRV_PCM_IOCTL1_RESET, NULL);
 	if (err < 0)
 		return err;
+	snd_pcm_stream_lock_irq(substream);
 	runtime->hw_ptr_base = 0;
 	runtime->hw_ptr_interrupt = runtime->status->hw_ptr -
 		runtime->status->hw_ptr % runtime->period_size;
 	runtime->silence_start = runtime->status->hw_ptr;
 	runtime->silence_filled = 0;
+	snd_pcm_stream_unlock_irq(substream);
 	return 0;
 }
 
@@ -1842,10 +1906,12 @@
 			       snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
+	snd_pcm_stream_lock_irq(substream);
 	runtime->control->appl_ptr = runtime->status->hw_ptr;
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
 	    runtime->silence_size > 0)
 		snd_pcm_playback_silence(substream, ULONG_MAX);
+	snd_pcm_stream_unlock_irq(substream);
 }
 
 static const struct action_ops snd_pcm_action_reset = {
@@ -1870,8 +1936,8 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	int f_flags = (__force int)state;
 
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN ||
-	    runtime->status->state == SNDRV_PCM_STATE_DISCONNECTED)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
 		return -EBADFD;
 	if (snd_pcm_running(substream))
 		return -EBUSY;
@@ -1922,7 +1988,7 @@
 		f_flags = substream->f_flags;
 
 	snd_pcm_stream_lock_irq(substream);
-	switch (substream->runtime->status->state) {
+	switch (substream->runtime->state) {
 	case SNDRV_PCM_STATE_PAUSED:
 		snd_pcm_pause(substream, false);
 		fallthrough;
@@ -1946,7 +2012,7 @@
 				  snd_pcm_state_t state)
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_OPEN:
 	case SNDRV_PCM_STATE_DISCONNECTED:
 	case SNDRV_PCM_STATE_SUSPENDED:
@@ -1961,28 +2027,28 @@
 {
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
-		switch (runtime->status->state) {
+		switch (runtime->state) {
 		case SNDRV_PCM_STATE_PREPARED:
 			/* start playback stream if possible */
 			if (! snd_pcm_playback_empty(substream)) {
 				snd_pcm_do_start(substream, SNDRV_PCM_STATE_DRAINING);
 				snd_pcm_post_start(substream, SNDRV_PCM_STATE_DRAINING);
 			} else {
-				runtime->status->state = SNDRV_PCM_STATE_SETUP;
+				__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_SETUP);
 			}
 			break;
 		case SNDRV_PCM_STATE_RUNNING:
-			runtime->status->state = SNDRV_PCM_STATE_DRAINING;
+			__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_DRAINING);
 			break;
 		case SNDRV_PCM_STATE_XRUN:
-			runtime->status->state = SNDRV_PCM_STATE_SETUP;
+			__snd_pcm_set_state(runtime, SNDRV_PCM_STATE_SETUP);
 			break;
 		default:
 			break;
 		}
 	} else {
 		/* stop running stream */
-		if (runtime->status->state == SNDRV_PCM_STATE_RUNNING) {
+		if (runtime->state == SNDRV_PCM_STATE_RUNNING) {
 			snd_pcm_state_t new_state;
 
 			new_state = snd_pcm_capture_avail(runtime) > 0 ?
@@ -1992,7 +2058,7 @@
 		}
 	}
 
-	if (runtime->status->state == SNDRV_PCM_STATE_DRAINING &&
+	if (runtime->state == SNDRV_PCM_STATE_DRAINING &&
 	    runtime->trigger_master == substream &&
 	    (runtime->hw.info & SNDRV_PCM_INFO_DRAIN_TRIGGER))
 		return substream->ops->trigger(substream,
@@ -2033,7 +2099,7 @@
 	card = substream->pcm->card;
 	runtime = substream->runtime;
 
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 
 	if (file) {
@@ -2044,7 +2110,7 @@
 
 	snd_pcm_stream_lock_irq(substream);
 	/* resume pause */
-	if (runtime->status->state == SNDRV_PCM_STATE_PAUSED)
+	if (runtime->state == SNDRV_PCM_STATE_PAUSED)
 		snd_pcm_pause(substream, false);
 
 	/* pre-start/stop - all running streams are changed to DRAINING state */
@@ -2072,7 +2138,7 @@
 			if (s->stream != SNDRV_PCM_STREAM_PLAYBACK)
 				continue;
 			runtime = s->runtime;
-			if (runtime->status->state == SNDRV_PCM_STATE_DRAINING) {
+			if (runtime->state == SNDRV_PCM_STATE_DRAINING) {
 				to_check = runtime;
 				break;
 			}
@@ -2111,7 +2177,7 @@
 			break;
 		}
 		if (tout == 0) {
-			if (substream->runtime->status->state == SNDRV_PCM_STATE_SUSPENDED)
+			if (substream->runtime->state == SNDRV_PCM_STATE_SUSPENDED)
 				result = -ESTRPIPE;
 			else {
 				dev_dbg(substream->pcm->card->dev,
@@ -2143,13 +2209,13 @@
 		return -ENXIO;
 	runtime = substream->runtime;
 
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN ||
-	    runtime->status->state == SNDRV_PCM_STATE_DISCONNECTED)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
 		return -EBADFD;
 
 	snd_pcm_stream_lock_irq(substream);
 	/* resume pause */
-	if (runtime->status->state == SNDRV_PCM_STATE_PAUSED)
+	if (runtime->state == SNDRV_PCM_STATE_PAUSED)
 		snd_pcm_pause(substream, false);
 
 	snd_pcm_stop(substream, SNDRV_PCM_STATE_SETUP);
@@ -2212,8 +2278,8 @@
 	snd_pcm_group_init(group);
 
 	down_write(&snd_pcm_link_rwsem);
-	if (substream->runtime->status->state == SNDRV_PCM_STATE_OPEN ||
-	    substream->runtime->status->state != substream1->runtime->status->state ||
+	if (substream->runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    substream->runtime->state != substream1->runtime->state ||
 	    substream->pcm->nonatomic != substream1->pcm->nonatomic) {
 		res = -EBADFD;
 		goto _end;
@@ -2637,7 +2703,7 @@
 
 	snd_pcm_drop(substream);
 	if (substream->hw_opened) {
-		if (substream->runtime->status->state != SNDRV_PCM_STATE_OPEN)
+		if (substream->runtime->state != SNDRV_PCM_STATE_OPEN)
 			do_hw_free(substream);
 		substream->ops->close(substream);
 		substream->hw_opened = 0;
@@ -2834,7 +2900,7 @@
  */
 static int do_pcm_hwsync(struct snd_pcm_substream *substream)
 {
-	switch (substream->runtime->status->state) {
+	switch (substream->runtime->state) {
 	case SNDRV_PCM_STATE_DRAINING:
 		if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
 			return -EBADFD;
@@ -3131,7 +3197,7 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	snd_pcm_sframes_t result;
 
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 	if (put_user(0, &_xferi->result))
 		return -EFAULT;
@@ -3154,7 +3220,7 @@
 	void *bufs;
 	snd_pcm_sframes_t result;
 
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 	if (runtime->channels > 128)
 		return -EINVAL;
@@ -3218,6 +3284,9 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 
+	if (substream->runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
+		return -EBADFD;
+
 	res = snd_power_wait(substream->pcm->card);
 	if (res < 0)
 		return res;
@@ -3344,6 +3413,9 @@
 	snd_pcm_uframes_t *frames = arg;
 	snd_pcm_sframes_t result;
 	
+	if (substream->runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
+		return -EBADFD;
+
 	switch (cmd) {
 	case SNDRV_PCM_IOCTL_FORWARD:
 	{
@@ -3386,7 +3458,8 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
 		return -EBADFD;
 	if (!frame_aligned(runtime, count))
 		return -EINVAL;
@@ -3410,7 +3483,8 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
 		return -EBADFD;
 	if (!frame_aligned(runtime, count))
 		return -EINVAL;
@@ -3436,7 +3510,8 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
 		return -EBADFD;
 	if (!iter_is_iovec(to))
 		return -EINVAL;
@@ -3472,7 +3547,8 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN ||
+	    runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
 		return -EBADFD;
 	if (!iter_is_iovec(from))
 		return -EINVAL;
@@ -3511,12 +3587,15 @@
 		return ok | EPOLLERR;
 
 	runtime = substream->runtime;
+	if (runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
+		return ok | EPOLLERR;
+
 	poll_wait(file, &runtime->sleep, wait);
 
 	mask = 0;
 	snd_pcm_stream_lock_irq(substream);
 	avail = snd_pcm_avail(substream);
-	switch (runtime->status->state) {
+	switch (runtime->state) {
 	case SNDRV_PCM_STATE_RUNNING:
 	case SNDRV_PCM_STATE_PREPARED:
 	case SNDRV_PCM_STATE_PAUSED:
@@ -3692,9 +3771,11 @@
 		return VM_FAULT_SIGBUS;
 	if (substream->ops->page)
 		page = substream->ops->page(substream, offset);
-	else if (!snd_pcm_get_dma_buf(substream))
+	else if (!snd_pcm_get_dma_buf(substream)) {
+		if (WARN_ON_ONCE(!runtime->dma_area))
+			return VM_FAULT_SIGBUS;
 		page = virt_to_page(runtime->dma_area + offset);
-	else
+	} else
 		page = snd_sgbuf_get_page(snd_pcm_get_dma_buf(substream), offset);
 	if (!page)
 		return VM_FAULT_SIGBUS;
@@ -3783,7 +3864,7 @@
 			return -EINVAL;
 	}
 	runtime = substream->runtime;
-	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+	if (runtime->state == SNDRV_PCM_STATE_OPEN)
 		return -EBADFD;
 	if (!(runtime->info & SNDRV_PCM_INFO_MMAP))
 		return -ENXIO;
@@ -3820,6 +3901,8 @@
 	substream = pcm_file->substream;
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
+	if (substream->runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
+		return -EBADFD;
 
 	offset = area->vm_pgoff << PAGE_SHIFT;
 	switch (offset) {
@@ -3856,6 +3939,8 @@
 	if (PCM_RUNTIME_CHECK(substream))
 		return -ENXIO;
 	runtime = substream->runtime;
+	if (runtime->state == SNDRV_PCM_STATE_DISCONNECTED)
+		return -EBADFD;
 	return fasync_helper(fd, file, on, &runtime->fasync);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/rawmidi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/rawmidi.c
@@ -447,6 +447,7 @@
 		err = -ENOMEM;
 		goto __error;
 	}
+	rawmidi_file->user_pversion = 0;
 	init_waitqueue_entry(&wait, current);
 	add_wait_queue(&rmidi->open_wait, &wait);
 	while (1) {
@@ -1834,10 +1835,8 @@
 
 	snd_info_free_entry(rmidi->proc_entry);
 	rmidi->proc_entry = NULL;
-	mutex_lock(&register_mutex);
 	if (rmidi->ops && rmidi->ops->dev_unregister)
 		rmidi->ops->dev_unregister(rmidi);
-	mutex_unlock(&register_mutex);
 
 	snd_rawmidi_free_substreams(&rmidi->streams[SNDRV_RAWMIDI_STREAM_INPUT]);
 	snd_rawmidi_free_substreams(&rmidi->streams[SNDRV_RAWMIDI_STREAM_OUTPUT]);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/seq/oss/seq_oss_midi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/seq/oss/seq_oss_midi.c
@@ -37,6 +37,7 @@
 	struct snd_midi_event *coder;	/* MIDI event coder */
 	struct seq_oss_devinfo *devinfo;	/* assigned OSSseq device */
 	snd_use_lock_t use_lock;
+	struct mutex open_mutex;
 };
 
 
@@ -172,6 +173,7 @@
 	mdev->flags = pinfo->capability;
 	mdev->opened = 0;
 	snd_use_lock_init(&mdev->use_lock);
+	mutex_init(&mdev->open_mutex);
 
 	/* copy and truncate the name of synth device */
 	strscpy(mdev->name, pinfo->name, sizeof(mdev->name));
@@ -270,7 +272,9 @@
 void
 snd_seq_oss_midi_setup(struct seq_oss_devinfo *dp)
 {
+	spin_lock_irq(&register_lock);
 	dp->max_mididev = max_midi_devs;
+	spin_unlock_irq(&register_lock);
 }
 
 /*
@@ -320,15 +324,17 @@
 	int perm;
 	struct seq_oss_midi *mdev;
 	struct snd_seq_port_subscribe subs;
+	int err;
 
 	mdev = get_mididev(dp, dev);
 	if (!mdev)
 		return -ENODEV;
 
+	mutex_lock(&mdev->open_mutex);
 	/* already used? */
 	if (mdev->opened && mdev->devinfo != dp) {
-		snd_use_lock_free(&mdev->use_lock);
-		return -EBUSY;
+		err = -EBUSY;
+		goto unlock;
 	}
 
 	perm = 0;
@@ -338,14 +344,14 @@
 		perm |= PERM_READ;
 	perm &= mdev->flags;
 	if (perm == 0) {
-		snd_use_lock_free(&mdev->use_lock);
-		return -ENXIO;
+		err = -ENXIO;
+		goto unlock;
 	}
 
 	/* already opened? */
 	if ((mdev->opened & perm) == perm) {
-		snd_use_lock_free(&mdev->use_lock);
-		return 0;
+		err = 0;
+		goto unlock;
 	}
 
 	perm &= ~mdev->opened;
@@ -370,13 +376,17 @@
 	}
 
 	if (! mdev->opened) {
-		snd_use_lock_free(&mdev->use_lock);
-		return -ENXIO;
+		err = -ENXIO;
+		goto unlock;
 	}
 
 	mdev->devinfo = dp;
+	err = 0;
+
+ unlock:
+	mutex_unlock(&mdev->open_mutex);
 	snd_use_lock_free(&mdev->use_lock);
-	return 0;
+	return err;
 }
 
 /*
@@ -391,10 +401,9 @@
 	mdev = get_mididev(dp, dev);
 	if (!mdev)
 		return -ENODEV;
-	if (! mdev->opened || mdev->devinfo != dp) {
-		snd_use_lock_free(&mdev->use_lock);
-		return 0;
-	}
+	mutex_lock(&mdev->open_mutex);
+	if (!mdev->opened || mdev->devinfo != dp)
+		goto unlock;
 
 	memset(&subs, 0, sizeof(subs));
 	if (mdev->opened & PERM_WRITE) {
@@ -413,6 +422,8 @@
 	mdev->opened = 0;
 	mdev->devinfo = NULL;
 
+ unlock:
+	mutex_unlock(&mdev->open_mutex);
 	snd_use_lock_free(&mdev->use_lock);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/seq/seq_clientmgr.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/seq/seq_clientmgr.c
@@ -121,13 +121,13 @@
 	spin_unlock_irqrestore(&clients_lock, flags);
 #ifdef CONFIG_MODULES
 	if (!in_interrupt()) {
-		static char client_requested[SNDRV_SEQ_GLOBAL_CLIENTS];
-		static char card_requested[SNDRV_CARDS];
+		static DECLARE_BITMAP(client_requested, SNDRV_SEQ_GLOBAL_CLIENTS);
+		static DECLARE_BITMAP(card_requested, SNDRV_CARDS);
+
 		if (clientid < SNDRV_SEQ_GLOBAL_CLIENTS) {
 			int idx;
 			
-			if (!client_requested[clientid]) {
-				client_requested[clientid] = 1;
+			if (!test_and_set_bit(clientid, client_requested)) {
 				for (idx = 0; idx < 15; idx++) {
 					if (seq_client_load[idx] < 0)
 						break;
@@ -142,10 +142,8 @@
 			int card = (clientid - SNDRV_SEQ_GLOBAL_CLIENTS) /
 				SNDRV_SEQ_CLIENTS_PER_CARD;
 			if (card < snd_ecards_limit) {
-				if (! card_requested[card]) {
-					card_requested[card] = 1;
+				if (!test_and_set_bit(card, card_requested))
 					snd_request_card(card);
-				}
 				snd_seq_device_load_drivers();
 			}
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/seq/seq_memory.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/seq/seq_memory.c
@@ -113,15 +113,19 @@
  * expand the variable length event to linear buffer space.
  */
 
-static int seq_copy_in_kernel(char **bufptr, const void *src, int size)
+static int seq_copy_in_kernel(void *ptr, void *src, int size)
 {
+	char **bufptr = ptr;
+
 	memcpy(*bufptr, src, size);
 	*bufptr += size;
 	return 0;
 }
 
-static int seq_copy_in_user(char __user **bufptr, const void *src, int size)
+static int seq_copy_in_user(void *ptr, void *src, int size)
 {
+	char __user **bufptr = ptr;
+
 	if (copy_to_user(*bufptr, src, size))
 		return -EFAULT;
 	*bufptr += size;
@@ -151,8 +155,7 @@
 		return newlen;
 	}
 	err = snd_seq_dump_var_event(event,
-				     in_kernel ? (snd_seq_dump_func_t)seq_copy_in_kernel :
-				     (snd_seq_dump_func_t)seq_copy_in_user,
+				     in_kernel ? seq_copy_in_kernel : seq_copy_in_user,
 				     &buf);
 	return err < 0 ? err : newlen;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/seq/seq_midi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/seq/seq_midi.c
@@ -112,6 +112,12 @@
 	return 0;
 }
 
+/* callback for snd_seq_dump_var_event(), bridging to dump_midi() */
+static int __dump_midi(void *ptr, void *buf, int count)
+{
+	return dump_midi(ptr, buf, count);
+}
+
 static int event_process_midi(struct snd_seq_event *ev, int direct,
 			      void *private_data, int atomic, int hop)
 {
@@ -131,7 +137,7 @@
 			pr_debug("ALSA: seq_midi: invalid sysex event flags = 0x%x\n", ev->flags);
 			return 0;
 		}
-		snd_seq_dump_var_event(ev, (snd_seq_dump_func_t)dump_midi, substream);
+		snd_seq_dump_var_event(ev, __dump_midi, substream);
 		snd_midi_event_reset_decode(msynth->parser);
 	} else {
 		if (msynth->parser == NULL)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/seq/seq_queue.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/seq/seq_queue.c
@@ -235,12 +235,15 @@
 
 /* -------------------------------------------------------- */
 
+#define MAX_CELL_PROCESSES_IN_QUEUE	1000
+
 void snd_seq_check_queue(struct snd_seq_queue *q, int atomic, int hop)
 {
 	unsigned long flags;
 	struct snd_seq_event_cell *cell;
 	snd_seq_tick_time_t cur_tick;
 	snd_seq_real_time_t cur_time;
+	int processed = 0;
 
 	if (q == NULL)
 		return;
@@ -263,6 +266,8 @@
 		if (!cell)
 			break;
 		snd_seq_dispatch_event(cell, atomic, hop);
+		if (++processed >= MAX_CELL_PROCESSES_IN_QUEUE)
+			goto out; /* the rest processed at the next batch */
 	}
 
 	/* Process time queue... */
@@ -272,14 +277,19 @@
 		if (!cell)
 			break;
 		snd_seq_dispatch_event(cell, atomic, hop);
+		if (++processed >= MAX_CELL_PROCESSES_IN_QUEUE)
+			goto out; /* the rest processed at the next batch */
 	}
 
+ out:
 	/* free lock */
 	spin_lock_irqsave(&q->check_lock, flags);
 	if (q->check_again) {
 		q->check_again = 0;
-		spin_unlock_irqrestore(&q->check_lock, flags);
-		goto __again;
+		if (processed < MAX_CELL_PROCESSES_IN_QUEUE) {
+			spin_unlock_irqrestore(&q->check_lock, flags);
+			goto __again;
+		}
 	}
 	q->check_blocked = 0;
 	spin_unlock_irqrestore(&q->check_lock, flags);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/seq/seq_virmidi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/seq/seq_virmidi.c
@@ -62,6 +62,13 @@
 /*
  * decode input event and put to read buffer of each opened file
  */
+
+/* callback for snd_seq_dump_var_event(), bridging to snd_rawmidi_receive() */
+static int dump_to_rawmidi(void *ptr, void *buf, int count)
+{
+	return snd_rawmidi_receive(ptr, buf, count);
+}
+
 static int snd_virmidi_dev_receive_event(struct snd_virmidi_dev *rdev,
 					 struct snd_seq_event *ev,
 					 bool atomic)
@@ -80,7 +87,7 @@
 		if (ev->type == SNDRV_SEQ_EVENT_SYSEX) {
 			if ((ev->flags & SNDRV_SEQ_EVENT_LENGTH_MASK) != SNDRV_SEQ_EVENT_LENGTH_VARIABLE)
 				continue;
-			snd_seq_dump_var_event(ev, (snd_seq_dump_func_t)snd_rawmidi_receive, vmidi->substream);
+			snd_seq_dump_var_event(ev, dump_to_rawmidi, vmidi->substream);
 			snd_midi_event_reset_decode(vmidi->parser);
 		} else {
 			len = snd_midi_event_decode(vmidi->parser, msg, sizeof(msg), ev);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/sound_oss.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/sound_oss.c
@@ -162,7 +162,6 @@
 		mutex_unlock(&sound_oss_mutex);
 		return -ENOENT;
 	}
-	unregister_sound_special(minor);
 	switch (SNDRV_MINOR_OSS_DEVICE(minor)) {
 	case SNDRV_MINOR_OSS_PCM:
 		track2 = SNDRV_MINOR_OSS(cidx, SNDRV_MINOR_OSS_AUDIO);
@@ -174,12 +173,18 @@
 		track2 = SNDRV_MINOR_OSS(cidx, SNDRV_MINOR_OSS_DMMIDI1);
 		break;
 	}
-	if (track2 >= 0) {
-		unregister_sound_special(track2);
+	if (track2 >= 0)
 		snd_oss_minors[track2] = NULL;
-	}
 	snd_oss_minors[minor] = NULL;
 	mutex_unlock(&sound_oss_mutex);
+
+	/* call unregister_sound_special() outside sound_oss_mutex;
+	 * otherwise may deadlock, as it can trigger the release of a card
+	 */
+	unregister_sound_special(minor);
+	if (track2 >= 0)
+		unregister_sound_special(track2);
+
 	kfree(mptr);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/core/timer.c
+++ linux-xilinx-zynqmp-5.15.0/sound/core/timer.c
@@ -83,7 +83,7 @@
 	unsigned int filter;
 	struct timespec64 tstamp;		/* trigger tstamp */
 	wait_queue_head_t qchange_sleep;
-	struct fasync_struct *fasync;
+	struct snd_fasync *fasync;
 	struct mutex ioctl_lock;
 };
 
@@ -553,6 +553,16 @@
 		goto unlock;
 	}
 
+	/* check the actual time for the start tick;
+	 * bail out as error if it's way too low (< 100us)
+	 */
+	if (start && !(timer->hw.flags & SNDRV_TIMER_HW_SLAVE)) {
+		if ((u64)snd_timer_hw_resolution(timer) * ticks < 100000) {
+			result = -EINVAL;
+			goto unlock;
+		}
+	}
+
 	if (start)
 		timeri->ticks = timeri->cticks = ticks;
 	else if (!timeri->cticks)
@@ -624,13 +634,13 @@
 	if (!timer)
 		return -EINVAL;
 	spin_lock_irqsave(&timer->lock, flags);
+	list_del_init(&timeri->ack_list);
+	list_del_init(&timeri->active_list);
 	if (!(timeri->flags & (SNDRV_TIMER_IFLG_RUNNING |
 			       SNDRV_TIMER_IFLG_START))) {
 		result = -EBUSY;
 		goto unlock;
 	}
-	list_del_init(&timeri->ack_list);
-	list_del_init(&timeri->active_list);
 	if (timer->card && timer->card->shutdown)
 		goto unlock;
 	if (stop) {
@@ -665,23 +675,22 @@
 static int snd_timer_stop_slave(struct snd_timer_instance *timeri, bool stop)
 {
 	unsigned long flags;
+	bool running;
 
 	spin_lock_irqsave(&slave_active_lock, flags);
-	if (!(timeri->flags & SNDRV_TIMER_IFLG_RUNNING)) {
-		spin_unlock_irqrestore(&slave_active_lock, flags);
-		return -EBUSY;
-	}
+	running = timeri->flags & SNDRV_TIMER_IFLG_RUNNING;
 	timeri->flags &= ~SNDRV_TIMER_IFLG_RUNNING;
 	if (timeri->timer) {
 		spin_lock(&timeri->timer->lock);
 		list_del_init(&timeri->ack_list);
 		list_del_init(&timeri->active_list);
-		snd_timer_notify1(timeri, stop ? SNDRV_TIMER_EVENT_STOP :
-				  SNDRV_TIMER_EVENT_PAUSE);
+		if (running)
+			snd_timer_notify1(timeri, stop ? SNDRV_TIMER_EVENT_STOP :
+					  SNDRV_TIMER_EVENT_PAUSE);
 		spin_unlock(&timeri->timer->lock);
 	}
 	spin_unlock_irqrestore(&slave_active_lock, flags);
-	return 0;
+	return running ? 0 : -EBUSY;
 }
 
 /*
@@ -1346,7 +1355,7 @@
 	}
       __wake:
 	spin_unlock(&tu->qlock);
-	kill_fasync(&tu->fasync, SIGIO, POLL_IN);
+	snd_kill_fasync(tu->fasync, SIGIO, POLL_IN);
 	wake_up(&tu->qchange_sleep);
 }
 
@@ -1384,7 +1393,7 @@
 	spin_lock_irqsave(&tu->qlock, flags);
 	snd_timer_user_append_to_tqueue(tu, &r1);
 	spin_unlock_irqrestore(&tu->qlock, flags);
-	kill_fasync(&tu->fasync, SIGIO, POLL_IN);
+	snd_kill_fasync(tu->fasync, SIGIO, POLL_IN);
 	wake_up(&tu->qchange_sleep);
 }
 
@@ -1454,7 +1463,7 @@
 	spin_unlock(&tu->qlock);
 	if (append == 0)
 		return;
-	kill_fasync(&tu->fasync, SIGIO, POLL_IN);
+	snd_kill_fasync(tu->fasync, SIGIO, POLL_IN);
 	wake_up(&tu->qchange_sleep);
 }
 
@@ -1522,6 +1531,7 @@
 			snd_timer_instance_free(tu->timeri);
 		}
 		mutex_unlock(&tu->ioctl_lock);
+		snd_fasync_free(tu->fasync);
 		kfree(tu->queue);
 		kfree(tu->tqueue);
 		kfree(tu);
@@ -2136,7 +2146,7 @@
 	struct snd_timer_user *tu;
 
 	tu = file->private_data;
-	return fasync_helper(fd, file, on, &tu->fasync);
+	return snd_fasync_helper(fd, file, on, &tu->fasync);
 }
 
 static ssize_t snd_timer_user_read(struct file *file, char __user *buffer,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/drivers/aloop.c
+++ linux-xilinx-zynqmp-5.15.0/sound/drivers/aloop.c
@@ -605,17 +605,18 @@
 			cable->streams[SNDRV_PCM_STREAM_PLAYBACK];
 	struct loopback_pcm *dpcm_capt =
 			cable->streams[SNDRV_PCM_STREAM_CAPTURE];
-	unsigned long delta_play = 0, delta_capt = 0;
+	unsigned long delta_play = 0, delta_capt = 0, cur_jiffies;
 	unsigned int running, count1, count2;
 
+	cur_jiffies = jiffies;
 	running = cable->running ^ cable->pause;
 	if (running & (1 << SNDRV_PCM_STREAM_PLAYBACK)) {
-		delta_play = jiffies - dpcm_play->last_jiffies;
+		delta_play = cur_jiffies - dpcm_play->last_jiffies;
 		dpcm_play->last_jiffies += delta_play;
 	}
 
 	if (running & (1 << SNDRV_PCM_STREAM_CAPTURE)) {
-		delta_capt = jiffies - dpcm_capt->last_jiffies;
+		delta_capt = cur_jiffies - dpcm_capt->last_jiffies;
 		dpcm_capt->last_jiffies += delta_capt;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/drivers/mtpav.c
+++ linux-xilinx-zynqmp-5.15.0/sound/drivers/mtpav.c
@@ -693,8 +693,6 @@
 	mtp_card->outmidihwport = 0xffffffff;
 	timer_setup(&mtp_card->timer, snd_mtpav_output_timer, 0);
 
-	card->private_free = snd_mtpav_free;
-
 	err = snd_mtpav_get_RAWMIDI(mtp_card);
 	if (err < 0)
 		return err;
@@ -716,6 +714,8 @@
 	if (err < 0)
 		return err;
 
+	card->private_free = snd_mtpav_free;
+
 	platform_set_drvdata(dev, card);
 	printk(KERN_INFO "Motu MidiTimePiece on parallel port irq: %d ioport: 0x%lx\n", irq, port);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/drivers/mts64.c
+++ linux-xilinx-zynqmp-5.15.0/sound/drivers/mts64.c
@@ -815,6 +815,9 @@
 	u8 status, data;
 	struct snd_rawmidi_substream *substream;
 
+	if (!mts)
+		return;
+
 	spin_lock(&mts->lock);
 	ret = mts64_read(mts->pardev->port);
 	data = ret & 0x00ff;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/drivers/opl3/opl3_midi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/drivers/opl3/opl3_midi.c
@@ -397,7 +397,7 @@
 	}
 	if (instr_4op) {
 		vp2 = &opl3->voices[voice + 3];
-		if (vp->state > 0) {
+		if (vp2->state > 0) {
 			opl3_reg = reg_side | (OPL3_REG_KEYON_BLOCK +
 					       voice_offset + 3);
 			reg_val = vp->keyon_reg & ~OPL3_KEYON_BIT;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/amdtp-stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/amdtp-stream.c
@@ -77,6 +77,8 @@
 // overrun. Actual device can skip more, then this module stops the packet streaming.
 #define IR_JUMBO_PAYLOAD_MAX_SKIP_CYCLES	5
 
+static void pcm_period_work(struct work_struct *work);
+
 /**
  * amdtp_stream_init - initialize an AMDTP stream structure
  * @s: the AMDTP stream to initialize
@@ -105,6 +107,7 @@
 	s->flags = flags;
 	s->context = ERR_PTR(-1);
 	mutex_init(&s->mutex);
+	INIT_WORK(&s->period_work, pcm_period_work);
 	s->packet_index = 0;
 
 	init_waitqueue_head(&s->ready_wait);
@@ -169,6 +172,9 @@
 			step = max(step, amdtp_syt_intervals[i]);
 	}
 
+	if (step == 0)
+		return -EINVAL;
+
 	t.min = roundup(s->min, step);
 	t.max = rounddown(s->max, step);
 	t.integer = 1;
@@ -343,6 +349,7 @@
  */
 void amdtp_stream_pcm_prepare(struct amdtp_stream *s)
 {
+	cancel_work_sync(&s->period_work);
 	s->pcm_buffer_pointer = 0;
 	s->pcm_period_pointer = 0;
 }
@@ -609,19 +616,21 @@
 		// The program in user process should periodically check the status of intermediate
 		// buffer associated to PCM substream to process PCM frames in the buffer, instead
 		// of receiving notification of period elapsed by poll wait.
-		if (!pcm->runtime->no_period_wakeup) {
-			if (in_softirq()) {
-				// In software IRQ context for 1394 OHCI.
-				snd_pcm_period_elapsed(pcm);
-			} else {
-				// In process context of ALSA PCM application under acquired lock of
-				// PCM substream.
-				snd_pcm_period_elapsed_under_stream_lock(pcm);
-			}
-		}
+		if (!pcm->runtime->no_period_wakeup)
+			queue_work(system_highpri_wq, &s->period_work);
 	}
 }
 
+static void pcm_period_work(struct work_struct *work)
+{
+	struct amdtp_stream *s = container_of(work, struct amdtp_stream,
+					      period_work);
+	struct snd_pcm_substream *pcm = READ_ONCE(s->pcm);
+
+	if (pcm)
+		snd_pcm_period_elapsed(pcm);
+}
+
 static int queue_packet(struct amdtp_stream *s, struct fw_iso_packet *params,
 			bool sched_irq)
 {
@@ -771,10 +780,14 @@
 	} else {
 		unsigned int dbc_interval;
 
-		if (*data_blocks > 0 && s->ctx_data.tx.dbc_interval > 0)
-			dbc_interval = s->ctx_data.tx.dbc_interval;
-		else
-			dbc_interval = *data_blocks;
+		if (!(s->flags & CIP_DBC_IS_PAYLOAD_QUADLETS)) {
+			if (*data_blocks > 0 && s->ctx_data.tx.dbc_interval > 0)
+				dbc_interval = s->ctx_data.tx.dbc_interval;
+			else
+				dbc_interval = *data_blocks;
+		} else {
+			dbc_interval = payload_length / sizeof(__be32);
+		}
 
 		lost = dbc != ((*data_block_counter + dbc_interval) & 0xff);
 	}
@@ -934,7 +947,7 @@
 				// to the reason.
 				unsigned int safe_cycle = increment_ohci_cycle_count(next_cycle,
 								IR_JUMBO_PAYLOAD_MAX_SKIP_CYCLES);
-				lost = (compare_ohci_cycle_count(safe_cycle, cycle) > 0);
+				lost = (compare_ohci_cycle_count(safe_cycle, cycle) < 0);
 			}
 			if (lost) {
 				dev_err(&s->unit->device, "Detect discontinuity of cycle: %d %d\n",
@@ -1734,11 +1747,14 @@
 {
 	struct amdtp_stream *irq_target = d->irq_target;
 
-	// Process isochronous packets queued till recent isochronous cycle to handle PCM frames.
 	if (irq_target && amdtp_stream_running(irq_target)) {
-		// In software IRQ context, the call causes dead-lock to disable the tasklet
-		// synchronously.
-		if (!in_softirq())
+		// use wq to prevent AB/BA deadlock competition for
+		// substream lock:
+		// fw_iso_context_flush_completions() acquires
+		// lock by ohci_flush_iso_completions(),
+		// amdtp-stream process_rx_packets() attempts to
+		// acquire same lock by snd_pcm_elapsed()
+		if (current_work() != &s->period_work)
 			fw_iso_context_flush_completions(irq_target->context);
 	}
 
@@ -1794,6 +1810,7 @@
 		return;
 	}
 
+	cancel_work_sync(&s->period_work);
 	fw_iso_context_stop(s->context);
 	fw_iso_context_destroy(s->context);
 	s->context = ERR_PTR(-1);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/amdtp-stream.h
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/amdtp-stream.h
@@ -37,6 +37,9 @@
  *	the value of current SYT_INTERVAL; e.g. initial value is not zero.
  * @CIP_UNAWARE_SYT: For outgoing packet, the value in SYT field of CIP is 0xffff.
  *	For incoming packet, the value in SYT field of CIP is not handled.
+ * @CIP_DBC_IS_PAYLOAD_QUADLETS: Available for incoming packet, and only effective with
+ *	CIP_DBC_IS_END_EVENT flag. The value of dbc field is the number of accumulated quadlets
+ *	in CIP payload, instead of the number of accumulated data blocks.
  */
 enum cip_flags {
 	CIP_NONBLOCKING		= 0x00,
@@ -51,6 +54,7 @@
 	CIP_NO_HEADER		= 0x100,
 	CIP_UNALIGHED_DBC	= 0x200,
 	CIP_UNAWARE_SYT		= 0x400,
+	CIP_DBC_IS_PAYLOAD_QUADLETS = 0x800,
 };
 
 /**
@@ -186,6 +190,7 @@
 
 	/* For a PCM substream processing. */
 	struct snd_pcm_substream *pcm;
+	struct work_struct period_work;
 	snd_pcm_uframes_t pcm_buffer_pointer;
 	unsigned int pcm_period_pointer;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/dice/dice-stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/dice/dice-stream.c
@@ -59,7 +59,7 @@
 
 static int select_clock(struct snd_dice *dice, unsigned int rate)
 {
-	__be32 reg;
+	__be32 reg, new;
 	u32 data;
 	int i;
 	int err;
@@ -83,15 +83,17 @@
 	if (completion_done(&dice->clock_accepted))
 		reinit_completion(&dice->clock_accepted);
 
-	reg = cpu_to_be32(data);
+	new = cpu_to_be32(data);
 	err = snd_dice_transaction_write_global(dice, GLOBAL_CLOCK_SELECT,
-						&reg, sizeof(reg));
+						&new, sizeof(new));
 	if (err < 0)
 		return err;
 
 	if (wait_for_completion_timeout(&dice->clock_accepted,
-			msecs_to_jiffies(NOTIFICATION_TIMEOUT_MS)) == 0)
-		return -ETIMEDOUT;
+			msecs_to_jiffies(NOTIFICATION_TIMEOUT_MS)) == 0) {
+		if (reg != new)
+			return -ETIMEDOUT;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/digi00x/digi00x-stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/digi00x/digi00x-stream.c
@@ -259,8 +259,10 @@
 		return err;
 
 	err = init_stream(dg00x, &dg00x->tx_stream);
-	if (err < 0)
+	if (err < 0) {
 		destroy_stream(dg00x, &dg00x->rx_stream);
+		return err;
+	}
 
 	err = amdtp_domain_init(&dg00x->domain);
 	if (err < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/fcp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/fcp.c
@@ -240,9 +240,7 @@
 	t.response_match_bytes = response_match_bytes;
 	t.state = STATE_PENDING;
 	init_waitqueue_head(&t.wait);
-
-	if (*(const u8 *)command == 0x00 || *(const u8 *)command == 0x03)
-		t.deferrable = true;
+	t.deferrable = (*(const u8 *)command == 0x00 || *(const u8 *)command == 0x03);
 
 	spin_lock_irq(&transactions_lock);
 	list_add_tail(&t.list, &transactions);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/fireworks/fireworks_hwdep.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/fireworks/fireworks_hwdep.c
@@ -34,6 +34,7 @@
 	type = SNDRV_FIREWIRE_EVENT_EFW_RESPONSE;
 	if (copy_to_user(buf, &type, sizeof(type)))
 		return -EFAULT;
+	count += sizeof(type);
 	remained -= sizeof(type);
 	buf += sizeof(type);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/oxfw/oxfw-stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/oxfw/oxfw-stream.c
@@ -9,7 +9,7 @@
 #include <linux/delay.h>
 
 #define AVC_GENERIC_FRAME_MAXIMUM_BYTES	512
-#define READY_TIMEOUT_MS	200
+#define READY_TIMEOUT_MS	600
 
 /*
  * According to datasheet of Oxford Semiconductor:
@@ -367,6 +367,11 @@
 				// Just after changing sampling transfer frequency, many cycles are
 				// skipped for packet transmission.
 				tx_init_skip_cycles = 400;
+			} else if (oxfw->quirks & SND_OXFW_QUIRK_VOLUNTARY_RECOVERY) {
+				// It takes a bit time for target device to adjust event frequency
+				// according to nominal event frequency in isochronous packets from
+				// ALSA oxfw driver.
+				tx_init_skip_cycles = 4000;
 			} else {
 				replay_seq = true;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/oxfw/oxfw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/oxfw/oxfw.c
@@ -25,6 +25,7 @@
 #define MODEL_SATELLITE		0x00200f
 #define MODEL_SCS1M		0x001000
 #define MODEL_DUET_FW		0x01dddd
+#define MODEL_ONYX_1640I	0x001640
 
 #define SPECIFIER_1394TA	0x00a02d
 #define VERSION_AVC		0x010001
@@ -192,6 +193,13 @@
 		// OXFW971-based models may transfer events by blocking method.
 		if (!(oxfw->quirks & SND_OXFW_QUIRK_JUMBO_PAYLOAD))
 			oxfw->quirks |= SND_OXFW_QUIRK_BLOCKING_TRANSMISSION;
+
+		if (model == MODEL_ONYX_1640I) {
+			//Unless receiving packets without NOINFO packet, the device transfers
+			//mostly half of events in packets than expected.
+			oxfw->quirks |= SND_OXFW_QUIRK_IGNORE_NO_INFO_PACKET |
+					SND_OXFW_QUIRK_VOLUNTARY_RECOVERY;
+		}
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/oxfw/oxfw.h
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/oxfw/oxfw.h
@@ -47,6 +47,11 @@
 	// the device to process audio data even if the value is invalid in a point of
 	// IEC 61883-1/6.
 	SND_OXFW_QUIRK_IGNORE_NO_INFO_PACKET = 0x10,
+	// Loud Technologies Mackie Onyx 1640i seems to configure OXFW971 ASIC so that it decides
+	// event frequency according to events in received isochronous packets. The device looks to
+	// performs media clock recovery voluntarily. In the recovery, the packets with NO_INFO
+	// are ignored, thus driver should transfer packets with timestamp.
+	SND_OXFW_QUIRK_VOLUNTARY_RECOVERY = 0x20,
 };
 
 /* This is an arbitrary number for convinience. */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/tascam/amdtp-tascam.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/tascam/amdtp-tascam.c
@@ -244,7 +244,7 @@
 	err = amdtp_stream_init(s, unit, dir, flags, fmt,
 			process_ctx_payloads, sizeof(struct amdtp_tscm));
 	if (err < 0)
-		return 0;
+		return err;
 
 	if (dir == AMDTP_OUT_STREAM) {
 		// Use fixed value for FDF field.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/firewire/tascam/tascam-stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/firewire/tascam/tascam-stream.c
@@ -490,7 +490,7 @@
 		// packet is important for media clock recovery.
 		err = amdtp_domain_start(&tscm->domain, tx_init_skip_cycles, true, true);
 		if (err < 0)
-			return err;
+			goto error;
 
 		if (!amdtp_domain_wait_ready(&tscm->domain, READY_TIMEOUT_MS)) {
 			err = -ETIMEDOUT;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/ext/hdac_ext_stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/ext/hdac_ext_stream.c
@@ -106,20 +106,14 @@
 }
 EXPORT_SYMBOL_GPL(snd_hdac_stream_free_all);
 
-/**
- * snd_hdac_ext_stream_decouple - decouple the hdac stream
- * @bus: HD-audio core bus
- * @stream: HD-audio ext core stream object to initialize
- * @decouple: flag to decouple
- */
-void snd_hdac_ext_stream_decouple(struct hdac_bus *bus,
-				struct hdac_ext_stream *stream, bool decouple)
+void snd_hdac_ext_stream_decouple_locked(struct hdac_bus *bus,
+					 struct hdac_ext_stream *stream,
+					 bool decouple)
 {
 	struct hdac_stream *hstream = &stream->hstream;
 	u32 val;
 	int mask = AZX_PPCTL_PROCEN(hstream->index);
 
-	spin_lock_irq(&bus->reg_lock);
 	val = readw(bus->ppcap + AZX_REG_PP_PPCTL) & mask;
 
 	if (decouple && !val)
@@ -128,6 +122,20 @@
 		snd_hdac_updatel(bus->ppcap, AZX_REG_PP_PPCTL, mask, 0);
 
 	stream->decoupled = decouple;
+}
+EXPORT_SYMBOL_GPL(snd_hdac_ext_stream_decouple_locked);
+
+/**
+ * snd_hdac_ext_stream_decouple - decouple the hdac stream
+ * @bus: HD-audio core bus
+ * @stream: HD-audio ext core stream object to initialize
+ * @decouple: flag to decouple
+ */
+void snd_hdac_ext_stream_decouple(struct hdac_bus *bus,
+				  struct hdac_ext_stream *stream, bool decouple)
+{
+	spin_lock_irq(&bus->reg_lock);
+	snd_hdac_ext_stream_decouple_locked(bus, stream, decouple);
 	spin_unlock_irq(&bus->reg_lock);
 }
 EXPORT_SYMBOL_GPL(snd_hdac_ext_stream_decouple);
@@ -252,6 +260,7 @@
 		return NULL;
 	}
 
+	spin_lock_irq(&bus->reg_lock);
 	list_for_each_entry(stream, &bus->stream_list, list) {
 		struct hdac_ext_stream *hstream = container_of(stream,
 						struct hdac_ext_stream,
@@ -266,17 +275,16 @@
 		}
 
 		if (!hstream->link_locked) {
-			snd_hdac_ext_stream_decouple(bus, hstream, true);
+			snd_hdac_ext_stream_decouple_locked(bus, hstream, true);
 			res = hstream;
 			break;
 		}
 	}
 	if (res) {
-		spin_lock_irq(&bus->reg_lock);
 		res->link_locked = 1;
 		res->link_substream = substream;
-		spin_unlock_irq(&bus->reg_lock);
 	}
+	spin_unlock_irq(&bus->reg_lock);
 	return res;
 }
 
@@ -292,6 +300,7 @@
 		return NULL;
 	}
 
+	spin_lock_irq(&bus->reg_lock);
 	list_for_each_entry(stream, &bus->stream_list, list) {
 		struct hdac_ext_stream *hstream = container_of(stream,
 						struct hdac_ext_stream,
@@ -301,18 +310,17 @@
 
 		if (!stream->opened) {
 			if (!hstream->decoupled)
-				snd_hdac_ext_stream_decouple(bus, hstream, true);
+				snd_hdac_ext_stream_decouple_locked(bus, hstream, true);
 			res = hstream;
 			break;
 		}
 	}
 	if (res) {
-		spin_lock_irq(&bus->reg_lock);
 		res->hstream.opened = 1;
 		res->hstream.running = 0;
 		res->hstream.substream = substream;
-		spin_unlock_irq(&bus->reg_lock);
 	}
+	spin_unlock_irq(&bus->reg_lock);
 
 	return res;
 }
@@ -378,15 +386,17 @@
 		break;
 
 	case HDAC_EXT_STREAM_TYPE_HOST:
+		spin_lock_irq(&bus->reg_lock);
 		if (stream->decoupled && !stream->link_locked)
-			snd_hdac_ext_stream_decouple(bus, stream, false);
+			snd_hdac_ext_stream_decouple_locked(bus, stream, false);
+		spin_unlock_irq(&bus->reg_lock);
 		snd_hdac_stream_release(&stream->hstream);
 		break;
 
 	case HDAC_EXT_STREAM_TYPE_LINK:
-		if (stream->decoupled && !stream->hstream.opened)
-			snd_hdac_ext_stream_decouple(bus, stream, false);
 		spin_lock_irq(&bus->reg_lock);
+		if (stream->decoupled && !stream->hstream.opened)
+			snd_hdac_ext_stream_decouple_locked(bus, stream, false);
 		stream->link_locked = 0;
 		stream->link_substream = NULL;
 		spin_unlock_irq(&bus->reg_lock);
@@ -465,23 +475,6 @@
 }
 EXPORT_SYMBOL_GPL(snd_hdac_ext_stream_get_spbmaxfifo);
 
-
-/**
- * snd_hdac_ext_stop_streams - stop all stream if running
- * @bus: HD-audio core bus
- */
-void snd_hdac_ext_stop_streams(struct hdac_bus *bus)
-{
-	struct hdac_stream *stream;
-
-	if (bus->chip_init) {
-		list_for_each_entry(stream, &bus->stream_list, list)
-			snd_hdac_stream_stop(stream);
-		snd_hdac_bus_stop_chip(bus);
-	}
-}
-EXPORT_SYMBOL_GPL(snd_hdac_ext_stop_streams);
-
 /**
  * snd_hdac_ext_stream_drsm_enable - enable DMA resume for a stream
  * @bus: HD-audio core bus
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/hdac_device.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/hdac_device.c
@@ -611,7 +611,7 @@
 int snd_hdac_keep_power_up(struct hdac_device *codec)
 {
 	if (!atomic_inc_not_zero(&codec->in_pm)) {
-		int ret = pm_runtime_get_if_in_use(&codec->dev);
+		int ret = pm_runtime_get_if_active(&codec->dev, true);
 		if (!ret)
 			return -1;
 		if (ret < 0)
@@ -660,6 +660,7 @@
 	{ 0x14f1, "Conexant" },
 	{ 0x17e8, "Chrontel" },
 	{ 0x1854, "LG" },
+	{ 0x19e5, "Huawei" },
 	{ 0x1aec, "Wolfson Microelectronics" },
 	{ 0x1af4, "QEMU" },
 	{ 0x434d, "C-Media" },
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/hdac_regmap.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/hdac_regmap.c
@@ -597,10 +597,9 @@
  */
 void snd_hdac_regmap_sync(struct hdac_device *codec)
 {
-	if (codec->regmap) {
-		mutex_lock(&codec->regmap_lock);
+	mutex_lock(&codec->regmap_lock);
+	if (codec->regmap)
 		regcache_sync(codec->regmap);
-		mutex_unlock(&codec->regmap_lock);
-	}
+	mutex_unlock(&codec->regmap_lock);
 }
 EXPORT_SYMBOL_GPL(snd_hdac_regmap_sync);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/hdac_stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/hdac_stream.c
@@ -143,6 +143,33 @@
 EXPORT_SYMBOL_GPL(snd_hdac_stream_stop);
 
 /**
+ * snd_hdac_stop_streams - stop all streams
+ * @bus: HD-audio core bus
+ */
+void snd_hdac_stop_streams(struct hdac_bus *bus)
+{
+	struct hdac_stream *stream;
+
+	list_for_each_entry(stream, &bus->stream_list, list)
+		snd_hdac_stream_stop(stream);
+}
+EXPORT_SYMBOL_GPL(snd_hdac_stop_streams);
+
+/**
+ * snd_hdac_stop_streams_and_chip - stop all streams and chip if running
+ * @bus: HD-audio core bus
+ */
+void snd_hdac_stop_streams_and_chip(struct hdac_bus *bus)
+{
+
+	if (bus->chip_init) {
+		snd_hdac_stop_streams(bus);
+		snd_hdac_bus_stop_chip(bus);
+	}
+}
+EXPORT_SYMBOL_GPL(snd_hdac_stop_streams_and_chip);
+
+/**
  * snd_hdac_stream_reset - reset a stream
  * @azx_dev: HD-audio core stream to reset
  */
@@ -293,9 +320,12 @@
 	struct hdac_stream *res = NULL;
 
 	/* make a non-zero unique key for the substream */
-	int key = (substream->pcm->device << 16) | (substream->number << 2) |
-		(substream->stream + 1);
+	int key = (substream->number << 2) | (substream->stream + 1);
 
+	if (substream->pcm)
+		key |= (substream->pcm->device << 16);
+
+	spin_lock_irq(&bus->reg_lock);
 	list_for_each_entry(azx_dev, &bus->stream_list, list) {
 		if (azx_dev->direction != substream->stream)
 			continue;
@@ -309,13 +339,12 @@
 			res = azx_dev;
 	}
 	if (res) {
-		spin_lock_irq(&bus->reg_lock);
 		res->opened = 1;
 		res->running = 0;
 		res->assigned_key = key;
 		res->substream = substream;
-		spin_unlock_irq(&bus->reg_lock);
 	}
+	spin_unlock_irq(&bus->reg_lock);
 	return res;
 }
 EXPORT_SYMBOL_GPL(snd_hdac_stream_assign);
@@ -534,17 +563,11 @@
 	cc->mask = CLOCKSOURCE_MASK(32);
 
 	/*
-	 * Converting from 24 MHz to ns means applying a 125/3 factor.
-	 * To avoid any saturation issues in intermediate operations,
-	 * the 125 factor is applied first. The division is applied
-	 * last after reading the timecounter value.
-	 * Applying the 1/3 factor as part of the multiplication
-	 * requires at least 20 bits for a decent precision, however
-	 * overflows occur after about 4 hours or less, not a option.
+	 * Calculate the optimal mult/shift values. The counter wraps
+	 * around after ~178.9 seconds.
 	 */
-
-	cc->mult = 125; /* saturation after 195 years */
-	cc->shift = 0;
+	clocks_calc_mult_shift(&cc->mult, &cc->shift, 24000000,
+			       NSEC_PER_SEC, 178);
 
 	nsec = 0; /* audio time is elapsed time since trigger */
 	timecounter_init(tc, cc, nsec);
@@ -575,17 +598,15 @@
 	struct hdac_stream *s;
 	bool inited = false;
 	u64 cycle_last = 0;
-	int i = 0;
 
 	list_for_each_entry(s, &bus->stream_list, list) {
-		if (streams & (1 << i)) {
+		if ((streams & (1 << s->index))) {
 			azx_timecounter_init(s, inited, cycle_last);
 			if (!inited) {
 				inited = true;
 				cycle_last = s->tc.cycle_last;
 			}
 		}
-		i++;
 	}
 
 	snd_pcm_gettime(runtime, &runtime->trigger_tstamp);
@@ -630,14 +651,13 @@
 			  unsigned int streams)
 {
 	struct hdac_bus *bus = azx_dev->bus;
-	int i, nwait, timeout;
+	int nwait, timeout;
 	struct hdac_stream *s;
 
 	for (timeout = 5000; timeout; timeout--) {
 		nwait = 0;
-		i = 0;
 		list_for_each_entry(s, &bus->stream_list, list) {
-			if (!(streams & (1 << i++)))
+			if (!(streams & (1 << s->index)))
 				continue;
 
 			if (start) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/hdac_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/hdac_sysfs.c
@@ -346,8 +346,10 @@
 		return -ENOMEM;
 	kobject_init(kobj, &widget_ktype);
 	err = kobject_add(kobj, parent, "%02x", nid);
-	if (err < 0)
+	if (err < 0) {
+		kobject_put(kobj);
 		return err;
+	}
 	err = sysfs_create_group(kobj, group);
 	if (err < 0) {
 		kobject_put(kobj);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/hdmi_chmap.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/hdmi_chmap.c
@@ -753,6 +753,20 @@
 	return 0;
 }
 
+/* a simple sanity check for input values to chmap kcontrol */
+static int chmap_value_check(struct hdac_chmap *hchmap,
+			     const struct snd_ctl_elem_value *ucontrol)
+{
+	int i;
+
+	for (i = 0; i < hchmap->channels_max; i++) {
+		if (ucontrol->value.integer.value[i] < 0 ||
+		    ucontrol->value.integer.value[i] > SNDRV_CHMAP_LAST)
+			return -EINVAL;
+	}
+	return 0;
+}
+
 static int hdmi_chmap_ctl_put(struct snd_kcontrol *kcontrol,
 			      struct snd_ctl_elem_value *ucontrol)
 {
@@ -764,6 +778,10 @@
 	unsigned char chmap[8], per_pin_chmap[8];
 	int i, err, ca, prepared = 0;
 
+	err = chmap_value_check(hchmap, ucontrol);
+	if (err < 0)
+		return err;
+
 	/* No monitor is connected in dyn_pcm_assign.
 	 * It's invalid to setup the chmap
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/intel-dsp-config.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/intel-dsp-config.c
@@ -31,6 +31,7 @@
 	u16 device;
 	u8 acpi_hid[ACPI_ID_LEN];
 	const struct dmi_system_id *dmi_table;
+	u8 codec_hid[ACPI_ID_LEN];
 };
 
 /*
@@ -56,7 +57,7 @@
 /*
  * Apollolake (Broxton-P)
  * the legacy HDAudio driver is used except on Up Squared (SOF) and
- * Chromebooks (SST)
+ * Chromebooks (SST), as well as devices based on the ES8336 codec
  */
 #if IS_ENABLED(CONFIG_SND_SOC_SOF_APOLLOLAKE)
 	{
@@ -73,6 +74,11 @@
 			{}
 		}
 	},
+	{
+		.flags = FLAG_SOF,
+		.device = 0x5a98,
+		.codec_hid = "ESSX8336",
+	},
 #endif
 #if IS_ENABLED(CONFIG_SND_SOC_INTEL_APL)
 	{
@@ -137,7 +143,7 @@
 
 /*
  * Geminilake uses legacy HDAudio driver except for Google
- * Chromebooks
+ * Chromebooks and devices based on the ES8336 codec
  */
 /* Geminilake */
 #if IS_ENABLED(CONFIG_SND_SOC_SOF_GEMINILAKE)
@@ -154,6 +160,11 @@
 			{}
 		}
 	},
+	{
+		.flags = FLAG_SOF,
+		.device = 0x3198,
+		.codec_hid = "ESSX8336",
+	},
 #endif
 
 /*
@@ -241,6 +252,11 @@
 		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
 		.device = 0x02c8,
 	},
+	{
+		.flags = FLAG_SOF,
+		.device = 0x02c8,
+		.codec_hid = "ESSX8336",
+	},
 /* Cometlake-H */
 	{
 		.flags = FLAG_SOF,
@@ -265,6 +281,11 @@
 		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
 		.device = 0x06c8,
 	},
+		{
+		.flags = FLAG_SOF,
+		.device = 0x06c8,
+		.codec_hid = "ESSX8336",
+	},
 #endif
 
 /* Icelake */
@@ -288,6 +309,15 @@
 	},
 #endif
 
+/* JasperLake */
+#if IS_ENABLED(CONFIG_SND_SOC_SOF_JASPERLAKE)
+	{
+		.flags = FLAG_SOF,
+		.device = 0x4dc8,
+		.codec_hid = "ESSX8336",
+	},
+#endif
+
 /* Tigerlake */
 #if IS_ENABLED(CONFIG_SND_SOC_SOF_TIGERLAKE)
 	{
@@ -300,6 +330,12 @@
 					DMI_MATCH(DMI_SYS_VENDOR, "Google"),
 				}
 			},
+			{
+				.ident = "Google firmware",
+				.matches = {
+					DMI_MATCH(DMI_BIOS_VERSION, "Google"),
+				}
+			},
 			{}
 		}
 	},
@@ -311,6 +347,11 @@
 		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
 		.device = 0x43c8,
 	},
+	{
+		.flags = FLAG_SOF,
+		.device = 0xa0c8,
+		.codec_hid = "ESSX8336",
+	},
 #endif
 
 /* Elkhart Lake */
@@ -341,6 +382,33 @@
 	},
 #endif
 
+/* Meteor Lake */
+#if IS_ENABLED(CONFIG_SND_SOC_SOF_METEORLAKE)
+	/* Meteorlake-P */
+	{
+		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
+		.device = 0x7e28,
+	},
+	/* ArrowLake-S */
+	{
+		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
+		.device = PCI_DEVICE_ID_INTEL_HDA_ARL_S,
+	},
+	/* ArrowLake */
+	{
+		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
+		.device = PCI_DEVICE_ID_INTEL_HDA_ARL,
+	},
+#endif
+
+/* Lunar Lake */
+#if IS_ENABLED(CONFIG_SND_SOC_SOF_LUNARLAKE)
+	/* Lunarlake-P */
+	{
+		.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
+		.device = PCI_DEVICE_ID_INTEL_HDA_LNL_P,
+	},
+#endif
 };
 
 static const struct config_entry *snd_intel_dsp_find_config
@@ -354,6 +422,8 @@
 			continue;
 		if (table->dmi_table && !dmi_check_system(table->dmi_table))
 			continue;
+		if (table->codec_hid[0] && !acpi_dev_present(table->codec_hid, NULL, -1))
+			continue;
 		return table;
 	}
 	return NULL;
@@ -491,6 +561,10 @@
 /* BayTrail */
 	{
 		.flags = FLAG_SST_OR_SOF_BYT,
+		.acpi_hid = "LPE0F28",
+	},
+	{
+		.flags = FLAG_SST_OR_SOF_BYT,
 		.acpi_hid = "80860F28",
 	},
 /* CherryTrail */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/intel-nhlt.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/intel-nhlt.c
@@ -55,20 +55,26 @@
 
 		/* find max number of channels based on format_configuration */
 		if (fmt_configs->fmt_count) {
-			dev_dbg(dev, "%s: found %d format definitions\n",
-				__func__, fmt_configs->fmt_count);
+			struct nhlt_fmt_cfg *fmt_cfg = fmt_configs->fmt_config;
+
+			dev_dbg(dev, "found %d format definitions\n",
+				fmt_configs->fmt_count);
 
 			for (i = 0; i < fmt_configs->fmt_count; i++) {
 				struct wav_fmt_ext *fmt_ext;
 
-				fmt_ext = &fmt_configs->fmt_config[i].fmt_ext;
+				fmt_ext = &fmt_cfg->fmt_ext;
 
 				if (fmt_ext->fmt.channels > max_ch)
 					max_ch = fmt_ext->fmt.channels;
+
+				/* Move to the next nhlt_fmt_cfg */
+				fmt_cfg = (struct nhlt_fmt_cfg *)(fmt_cfg->config.caps +
+								  fmt_cfg->config.size);
 			}
-			dev_dbg(dev, "%s: max channels found %d\n", __func__, max_ch);
+			dev_dbg(dev, "max channels found %d\n", max_ch);
 		} else {
-			dev_dbg(dev, "%s: No format information found\n", __func__);
+			dev_dbg(dev, "No format information found\n");
 		}
 
 		if (cfg->device_config.config_type != NHLT_CONFIG_TYPE_MIC_ARRAY) {
@@ -95,17 +101,16 @@
 			}
 
 			if (dmic_geo > 0) {
-				dev_dbg(dev, "%s: Array with %d dmics\n", __func__, dmic_geo);
+				dev_dbg(dev, "Array with %d dmics\n", dmic_geo);
 			}
 			if (max_ch > dmic_geo) {
-				dev_dbg(dev, "%s: max channels %d exceed dmic number %d\n",
-					__func__, max_ch, dmic_geo);
+				dev_dbg(dev, "max channels %d exceed dmic number %d\n",
+					max_ch, dmic_geo);
 			}
 		}
 	}
 
-	dev_dbg(dev, "%s: dmic number %d max_ch %d\n",
-		__func__, dmic_geo, max_ch);
+	dev_dbg(dev, "dmic number %d max_ch %d\n", dmic_geo, max_ch);
 
 	return dmic_geo;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/hda/intel-sdw-acpi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/hda/intel-sdw-acpi.c
@@ -41,6 +41,8 @@
 				 "intel-quirk-mask",
 				 &quirk_mask);
 
+	fwnode_handle_put(link);
+
 	if (quirk_mask & SDW_INTEL_QUIRK_MASK_BUS_DISABLE)
 		return false;
 
@@ -132,8 +134,6 @@
 		return AE_NOT_FOUND;
 	}
 
-	info->handle = handle;
-
 	/*
 	 * On some Intel platforms, multiple children of the HDAS
 	 * device can be found, but only one of them is the SoundWire
@@ -144,6 +144,9 @@
 	if (FIELD_GET(GENMASK(31, 28), adr) != SDW_LINK_TYPE)
 		return AE_OK; /* keep going */
 
+	/* found the correct SoundWire controller */
+	info->handle = handle;
+
 	/* device found, stop namespace walk */
 	return AE_CTRL_TERMINATE;
 }
@@ -164,8 +167,14 @@
 	acpi_status status;
 
 	info->handle = NULL;
+	/*
+	 * In the HDAS ACPI scope, 'SNDW' may be either the child of
+	 * 'HDAS' or the grandchild of 'HDAS'. So let's go through
+	 * the ACPI from 'HDAS' at max depth of 2 to find the 'SNDW'
+	 * device.
+	 */
 	status = acpi_walk_namespace(ACPI_TYPE_DEVICE,
-				     parent_handle, 1,
+				     parent_handle, 2,
 				     sdw_intel_acpi_cb,
 				     NULL, info, NULL);
 	if (ACPI_FAILURE(status) || info->handle == NULL)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/i2c/cs8427.c
+++ linux-xilinx-zynqmp-5.15.0/sound/i2c/cs8427.c
@@ -561,10 +561,13 @@
 	if (snd_BUG_ON(!cs8427))
 		return -ENXIO;
 	chip = cs8427->private_data;
-	if (active)
+	if (active) {
 		memcpy(chip->playback.pcm_status,
 		       chip->playback.def_status, 24);
-	chip->playback.pcm_ctl->vd[0].access &= ~SNDRV_CTL_ELEM_ACCESS_INACTIVE;
+		chip->playback.pcm_ctl->vd[0].access &= ~SNDRV_CTL_ELEM_ACCESS_INACTIVE;
+	} else {
+		chip->playback.pcm_ctl->vd[0].access |= SNDRV_CTL_ELEM_ACCESS_INACTIVE;
+	}
 	snd_ctl_notify(cs8427->bus->card,
 		       SNDRV_CTL_EVENT_MASK_VALUE | SNDRV_CTL_EVENT_MASK_INFO,
 		       &chip->playback.pcm_ctl->id);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/isa/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/isa/Kconfig
@@ -22,7 +22,7 @@
 menuconfig SND_ISA
 	bool "ISA sound devices"
 	depends on ISA || COMPILE_TEST
-	depends on ISA_DMA_API
+	depends on ISA_DMA_API && !M68K
 	default y
 	help
 	  Support for sound devices connected via the ISA bus.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/isa/cs423x/cs4236.c
+++ linux-xilinx-zynqmp-5.15.0/sound/isa/cs423x/cs4236.c
@@ -494,7 +494,7 @@
 	static int dev;
 	int err;
 	struct snd_card *card;
-	struct pnp_dev *cdev;
+	struct pnp_dev *cdev, *iter;
 	char cid[PNP_ID_LEN];
 
 	if (pnp_device_is_isapnp(pdev))
@@ -510,9 +510,11 @@
 	strcpy(cid, pdev->id[0].id);
 	cid[5] = '1';
 	cdev = NULL;
-	list_for_each_entry(cdev, &(pdev->protocol->devices), protocol_list) {
-		if (!strcmp(cdev->id[0].id, cid))
+	list_for_each_entry(iter, &(pdev->protocol->devices), protocol_list) {
+		if (!strcmp(iter->id[0].id, cid)) {
+			cdev = iter;
 			break;
+		}
 	}
 	err = snd_cs423x_card_new(&pdev->dev, dev, &card);
 	if (err < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/isa/galaxy/galaxy.c
+++ linux-xilinx-zynqmp-5.15.0/sound/isa/galaxy/galaxy.c
@@ -478,7 +478,7 @@
 		galaxy_set_config(galaxy, galaxy->config);
 }
 
-static int snd_galaxy_probe(struct device *dev, unsigned int n)
+static int __snd_galaxy_probe(struct device *dev, unsigned int n)
 {
 	struct snd_galaxy *galaxy;
 	struct snd_wss *chip;
@@ -598,6 +598,11 @@
 	return 0;
 }
 
+static int snd_galaxy_probe(struct device *dev, unsigned int n)
+{
+	return snd_card_free_on_error(dev, __snd_galaxy_probe(dev, n));
+}
+
 static struct isa_driver snd_galaxy_driver = {
 	.match		= snd_galaxy_match,
 	.probe		= snd_galaxy_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/isa/gus/gus_dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/isa/gus/gus_dma.c
@@ -126,6 +126,8 @@
 	}
 	block = snd_gf1_dma_next_block(gus);
 	spin_unlock(&gus->dma_lock);
+	if (!block)
+		return;
 	snd_gf1_dma_program(gus, block->addr, block->buf_addr, block->count, (unsigned short) block->cmd);
 	kfree(block);
 #if 0
--- linux-xilinx-zynqmp-5.15.0.orig/sound/isa/sc6000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/isa/sc6000.c
@@ -537,7 +537,7 @@
 		sc6000_setup_board(vport, 0);
 }
 
-static int snd_sc6000_probe(struct device *devptr, unsigned int dev)
+static int __snd_sc6000_probe(struct device *devptr, unsigned int dev)
 {
 	static const int possible_irqs[] = { 5, 7, 9, 10, 11, -1 };
 	static const int possible_dmas[] = { 1, 3, 0, -1 };
@@ -662,6 +662,11 @@
 	return 0;
 }
 
+static int snd_sc6000_probe(struct device *devptr, unsigned int dev)
+{
+	return snd_card_free_on_error(devptr, __snd_sc6000_probe(devptr, dev));
+}
+
 static struct isa_driver snd_sc6000_driver = {
 	.match		= snd_sc6000_match,
 	.probe		= snd_sc6000_probe,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/isa/wavefront/wavefront_synth.c
+++ linux-xilinx-zynqmp-5.15.0/sound/isa/wavefront/wavefront_synth.c
@@ -1094,7 +1094,8 @@
 
 			if (dataptr < data_end) {
 		
-				__get_user (sample_short, dataptr);
+				if (get_user(sample_short, dataptr))
+					return -EFAULT;
 				dataptr += skip;
 		
 				if (data_is_unsigned) { /* GUS ? */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/oss/dmasound/dmasound.h
+++ linux-xilinx-zynqmp-5.15.0/sound/oss/dmasound/dmasound.h
@@ -88,11 +88,7 @@
      */
 
 extern int dmasound_init(void);
-#ifdef MODULE
 extern void dmasound_deinit(void);
-#else
-#define dmasound_deinit()	do { } while (0)
-#endif
 
 /* description of the set-up applies to either hard or soft settings */
 
@@ -114,9 +110,7 @@
     void *(*dma_alloc)(unsigned int, gfp_t);
     void (*dma_free)(void *, unsigned int);
     int (*irqinit)(void);
-#ifdef MODULE
     void (*irqcleanup)(void);
-#endif
     void (*init)(void);
     void (*silence)(void);
     int (*setFormat)(int);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/oss/dmasound/dmasound_core.c
+++ linux-xilinx-zynqmp-5.15.0/sound/oss/dmasound/dmasound_core.c
@@ -206,12 +206,10 @@
 
 MODULE_LICENSE("GPL");
 
-#ifdef MODULE
 static int sq_unit = -1;
 static int mixer_unit = -1;
 static int state_unit = -1;
 static int irq_installed;
-#endif /* MODULE */
 
 /* control over who can modify resources shared between play/record */
 static fmode_t shared_resource_owner;
@@ -391,9 +389,6 @@
 
 static void mixer_init(void)
 {
-#ifndef MODULE
-	int mixer_unit;
-#endif
 	mixer_unit = register_sound_mixer(&mixer_fops, -1);
 	if (mixer_unit < 0)
 		return;
@@ -1171,9 +1166,6 @@
 static int sq_init(void)
 {
 	const struct file_operations *fops = &sq_fops;
-#ifndef MODULE
-	int sq_unit;
-#endif
 
 	sq_unit = register_sound_dsp(fops, -1);
 	if (sq_unit < 0) {
@@ -1366,9 +1358,6 @@
 
 static int state_init(void)
 {
-#ifndef MODULE
-	int state_unit;
-#endif
 	state_unit = register_sound_special(&state_fops, SND_DEV_STATUS);
 	if (state_unit < 0)
 		return state_unit ;
@@ -1386,10 +1375,9 @@
 int dmasound_init(void)
 {
 	int res ;
-#ifdef MODULE
+
 	if (irq_installed)
 		return -EBUSY;
-#endif
 
 	/* Set up sound queue, /dev/audio and /dev/dsp. */
 
@@ -1408,9 +1396,7 @@
 		printk(KERN_ERR "DMA sound driver: Interrupt initialization failed\n");
 		return -ENODEV;
 	}
-#ifdef MODULE
 	irq_installed = 1;
-#endif
 
 	printk(KERN_INFO "%s DMA sound driver rev %03d installed\n",
 		dmasound.mach.name, (DMASOUND_CORE_REVISION<<4) +
@@ -1424,8 +1410,6 @@
 	return 0;
 }
 
-#ifdef MODULE
-
 void dmasound_deinit(void)
 {
 	if (irq_installed) {
@@ -1444,9 +1428,7 @@
 		unregister_sound_dsp(sq_unit);
 }
 
-#else /* !MODULE */
-
-static int dmasound_setup(char *str)
+static int __maybe_unused dmasound_setup(char *str)
 {
 	int ints[6], size;
 
@@ -1489,8 +1471,6 @@
 
 __setup("dmasound=", dmasound_setup);
 
-#endif /* !MODULE */
-
     /*
      *  Conversion tables
      */
@@ -1577,9 +1557,7 @@
 
 EXPORT_SYMBOL(dmasound);
 EXPORT_SYMBOL(dmasound_init);
-#ifdef MODULE
 EXPORT_SYMBOL(dmasound_deinit);
-#endif
 EXPORT_SYMBOL(dmasound_write_sq);
 EXPORT_SYMBOL(dmasound_catchRadius);
 #ifdef HAS_8BIT_TABLES
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/Kconfig
@@ -279,6 +279,7 @@
 config SND_CS5530
 	tristate "CS5530 Audio"
 	depends on ISA_DMA_API && (X86_32 || COMPILE_TEST)
+	depends on !M68K
 	select SND_SB16_DSP
 	help
 	  Say Y here to include support for audio on Cyrix/NatSemi CS5530 chips.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ac97/ac97_codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ac97/ac97_codec.c
@@ -938,8 +938,8 @@
 	int codec = kcontrol->private_value & 3;
 	
 	mutex_lock(&ac97->page_mutex);
-	ucontrol->value.integer.value[0] = 31 - ((ac97->spec.ad18xx.pcmreg[codec] >> 0) & 31);
-	ucontrol->value.integer.value[1] = 31 - ((ac97->spec.ad18xx.pcmreg[codec] >> 8) & 31);
+	ucontrol->value.integer.value[0] = 31 - ((ac97->spec.ad18xx.pcmreg[codec] >> 8) & 31);
+	ucontrol->value.integer.value[1] = 31 - ((ac97->spec.ad18xx.pcmreg[codec] >> 0) & 31);
 	mutex_unlock(&ac97->page_mutex);
 	return 0;
 }
@@ -2009,6 +2009,7 @@
 	err = device_register(&ac97->dev);
 	if (err < 0) {
 		ac97_err(ac97, "Can't register ac97 bus\n");
+		put_device(&ac97->dev);
 		ac97->dev.bus = NULL;
 		return err;
 	}
@@ -2069,10 +2070,9 @@
 		.dev_disconnect =	snd_ac97_dev_disconnect,
 	};
 
-	if (rac97)
-		*rac97 = NULL;
-	if (snd_BUG_ON(!bus || !template))
+	if (snd_BUG_ON(!bus || !template || !rac97))
 		return -EINVAL;
+	*rac97 = NULL;
 	if (snd_BUG_ON(template->num >= 4))
 		return -EINVAL;
 	if (bus->codec[template->num])
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ad1889.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ad1889.c
@@ -844,8 +844,8 @@
 }
 
 static int
-snd_ad1889_probe(struct pci_dev *pci,
-		 const struct pci_device_id *pci_id)
+__snd_ad1889_probe(struct pci_dev *pci,
+		   const struct pci_device_id *pci_id)
 {
 	int err;
 	static int devno;
@@ -904,6 +904,12 @@
 	return 0;
 }
 
+static int snd_ad1889_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_ad1889_probe(pci, pci_id));
+}
+
 static const struct pci_device_id snd_ad1889_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_ANALOG_DEVICES, PCI_DEVICE_ID_AD1889JS) },
 	{ 0, },
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ali5451/ali5451.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ali5451/ali5451.c
@@ -2124,8 +2124,8 @@
 	return 0;
 }
 
-static int snd_ali_probe(struct pci_dev *pci,
-			 const struct pci_device_id *pci_id)
+static int __snd_ali_probe(struct pci_dev *pci,
+			   const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct snd_ali *codec;
@@ -2170,6 +2170,12 @@
 	return 0;
 }
 
+static int snd_ali_probe(struct pci_dev *pci,
+			 const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_ali_probe(pci, pci_id));
+}
+
 static struct pci_driver ali5451_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_ali_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/als300.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/als300.c
@@ -708,7 +708,7 @@
 
 	err = snd_als300_create(card, pci, chip_type);
 	if (err < 0)
-		return err;
+		goto error;
 
 	strcpy(card->driver, "ALS300");
 	if (chip->chip_type == DEVICE_ALS300_PLUS)
@@ -723,11 +723,15 @@
 
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver als300_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/als4000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/als4000.c
@@ -806,8 +806,8 @@
 	snd_als4000_free_gameport(acard);
 }
 
-static int snd_card_als4000_probe(struct pci_dev *pci,
-				  const struct pci_device_id *pci_id)
+static int __snd_card_als4000_probe(struct pci_dev *pci,
+				    const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -930,6 +930,12 @@
 	return 0;
 }
 
+static int snd_card_als4000_probe(struct pci_dev *pci,
+				  const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_card_als4000_probe(pci, pci_id));
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int snd_als4000_suspend(struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/asihpi/hpi6205.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/asihpi/hpi6205.c
@@ -430,7 +430,7 @@
 		pao = hpi_find_adapter(phm->adapter_index);
 	} else {
 		/* subsys messages don't address an adapter */
-		_HPI_6205(NULL, phm, phr);
+		phr->error = HPI_ERROR_INVALID_OBJ_INDEX;
 		return;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/asihpi/hpimsgx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/asihpi/hpimsgx.c
@@ -713,7 +713,7 @@
 		phr->error = HPI_ERROR_PROCESSING_MESSAGE;
 		return phr->error;
 	}
-	if (hr.error == 0) {
+	if (hr.error == 0 && hr.u.s.adapter_index < HPI_MAX_ADAPTERS) {
 		/* the adapter was created successfully
 		   save the mapping for future use */
 		hpi_entry_points[hr.u.s.adapter_index] = entry_point_func;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/asihpi/hpioctl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/asihpi/hpioctl.c
@@ -361,7 +361,7 @@
 		pci_dev->device, pci_dev->subsystem_vendor,
 		pci_dev->subsystem_device, pci_dev->devfn);
 
-	if (pci_enable_device(pci_dev) < 0) {
+	if (pcim_enable_device(pci_dev) < 0) {
 		dev_err(&pci_dev->dev,
 			"pci_enable_device failed, disabling device\n");
 		return -EIO;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/atiixp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/atiixp.c
@@ -1572,8 +1572,8 @@
 }
 
 
-static int snd_atiixp_probe(struct pci_dev *pci,
-			    const struct pci_device_id *pci_id)
+static int __snd_atiixp_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct atiixp *chip;
@@ -1623,6 +1623,12 @@
 	return 0;
 }
 
+static int snd_atiixp_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_atiixp_probe(pci, pci_id));
+}
+
 static struct pci_driver atiixp_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_atiixp_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/atiixp_modem.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/atiixp_modem.c
@@ -1201,8 +1201,8 @@
 }
 
 
-static int snd_atiixp_probe(struct pci_dev *pci,
-			    const struct pci_device_id *pci_id)
+static int __snd_atiixp_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct atiixp_modem *chip;
@@ -1247,6 +1247,12 @@
 	return 0;
 }
 
+static int snd_atiixp_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_atiixp_probe(pci, pci_id));
+}
+
 static struct pci_driver atiixp_modem_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_atiixp_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/au88x0/au88x0.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/au88x0/au88x0.c
@@ -193,7 +193,7 @@
 
 // constructor -- see "Constructor" sub-section
 static int
-snd_vortex_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+__snd_vortex_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -310,6 +310,12 @@
 	return 0;
 }
 
+static int
+snd_vortex_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_vortex_probe(pci, pci_id));
+}
+
 // pci_driver definition
 static struct pci_driver vortex_driver = {
 	.name = KBUILD_MODNAME,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/au88x0/au88x0.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/au88x0/au88x0.h
@@ -141,7 +141,7 @@
 #ifndef CHIP_AU8810
 	stream_t dma_wt[NR_WT];
 	wt_voice_t wt_voice[NR_WT];	/* WT register cache. */
-	char mixwt[(NR_WT / NR_WTPB) * 6];	/* WT mixin objects */
+	s8 mixwt[(NR_WT / NR_WTPB) * 6];	/* WT mixin objects */
 #endif
 
 	/* Global resources */
@@ -235,8 +235,8 @@
 static void vortex_connect_default(vortex_t * vortex, int en);
 static int vortex_adb_allocroute(vortex_t * vortex, int dma, int nr_ch,
 				 int dir, int type, int subdev);
-static char vortex_adb_checkinout(vortex_t * vortex, int resmap[], int out,
-				  int restype);
+static int vortex_adb_checkinout(vortex_t * vortex, int resmap[], int out,
+				 int restype);
 #ifndef CHIP_AU8810
 static int vortex_wt_allocroute(vortex_t * vortex, int dma, int nr_ch);
 static void vortex_wt_connect(vortex_t * vortex, int en);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/au88x0/au88x0_core.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/au88x0/au88x0_core.c
@@ -1998,7 +1998,7 @@
  out: Mean checkout if != 0. Else mean Checkin resource.
  restype: Indicates type of resource to be checked in or out.
 */
-static char
+static int
 vortex_adb_checkinout(vortex_t * vortex, int resmap[], int out, int restype)
 {
 	int i, qty = resnum[restype], resinuse = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/aw2/aw2-alsa.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/aw2/aw2-alsa.c
@@ -275,7 +275,7 @@
 	/* (3) Create main component */
 	err = snd_aw2_create(card, pci);
 	if (err < 0)
-		return err;
+		goto error;
 
 	/* initialize mutex */
 	mutex_init(&chip->mtx);
@@ -294,13 +294,17 @@
 	/* (6) Register card instance */
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 
 	/* (7) Set PCI driver data */
 	pci_set_drvdata(pci, card);
 
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 /* open callback */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/azt3328.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/azt3328.c
@@ -2427,7 +2427,7 @@
 }
 
 static int
-snd_azf3328_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+__snd_azf3328_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2520,6 +2520,12 @@
 	return 0;
 }
 
+static int
+snd_azf3328_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_azf3328_probe(pci, pci_id));
+}
+
 #ifdef CONFIG_PM_SLEEP
 static inline void
 snd_azf3328_suspend_regs(const struct snd_azf3328 *chip,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/bt87x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/bt87x.c
@@ -805,8 +805,8 @@
 	return SND_BT87X_BOARD_UNKNOWN;
 }
 
-static int snd_bt87x_probe(struct pci_dev *pci,
-			   const struct pci_device_id *pci_id)
+static int __snd_bt87x_probe(struct pci_dev *pci,
+			     const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -889,6 +889,12 @@
 	return 0;
 }
 
+static int snd_bt87x_probe(struct pci_dev *pci,
+			   const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_bt87x_probe(pci, pci_id));
+}
+
 /* default entries for all Bt87x cards - it's not exported */
 /* driver_data is set to 0 to call detection */
 static const struct pci_device_id snd_bt87x_default_ids[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ca0106/ca0106_main.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ca0106/ca0106_main.c
@@ -1725,8 +1725,8 @@
 }
 
 
-static int snd_ca0106_probe(struct pci_dev *pci,
-					const struct pci_device_id *pci_id)
+static int __snd_ca0106_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -1786,6 +1786,12 @@
 	return 0;
 }
 
+static int snd_ca0106_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_ca0106_probe(pci, pci_id));
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int snd_ca0106_suspend(struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/cmipci.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/cmipci.c
@@ -298,7 +298,6 @@
 #define CM_MICGAINZ		0x01	/* mic boost */
 #define CM_MICGAINZ_SHIFT	0
 
-#define CM_REG_MIXER3		0x24
 #define CM_REG_AUX_VOL		0x26
 #define CM_VAUXL_MASK		0xf0
 #define CM_VAUXR_MASK		0x0f
@@ -3250,15 +3249,19 @@
 
 	err = snd_cmipci_create(card, pci, dev);
 	if (err < 0)
-		return err;
+		goto error;
 
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 #ifdef CONFIG_PM_SLEEP
@@ -3267,7 +3270,7 @@
  */
 static const unsigned char saved_regs[] = {
 	CM_REG_FUNCTRL1, CM_REG_CHFORMAT, CM_REG_LEGACY_CTRL, CM_REG_MISC_CTRL,
-	CM_REG_MIXER0, CM_REG_MIXER1, CM_REG_MIXER2, CM_REG_MIXER3, CM_REG_PLL,
+	CM_REG_MIXER0, CM_REG_MIXER1, CM_REG_MIXER2, CM_REG_AUX_VOL, CM_REG_PLL,
 	CM_REG_CH0_FRAME1, CM_REG_CH0_FRAME2,
 	CM_REG_CH1_FRAME1, CM_REG_CH1_FRAME2, CM_REG_EXT_MISC,
 	CM_REG_INT_STATUS, CM_REG_INT_HLDCLR, CM_REG_FUNCTRL0,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/cs4281.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/cs4281.c
@@ -1827,8 +1827,8 @@
 	spin_unlock_irqrestore(&opl3->reg_lock, flags);
 }
 
-static int snd_cs4281_probe(struct pci_dev *pci,
-			    const struct pci_device_id *pci_id)
+static int __snd_cs4281_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -1888,6 +1888,12 @@
 	return 0;
 }
 
+static int snd_cs4281_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_cs4281_probe(pci, pci_id));
+}
+
 /*
  * Power Management
  */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/cs46xx/cs46xx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/cs46xx/cs46xx.c
@@ -74,36 +74,36 @@
 	err = snd_cs46xx_create(card, pci,
 				external_amp[dev], thinkpad[dev]);
 	if (err < 0)
-		return err;
+		goto error;
 	card->private_data = chip;
 	chip->accept_valid = mmap_valid[dev];
 	err = snd_cs46xx_pcm(chip, 0);
 	if (err < 0)
-		return err;
+		goto error;
 #ifdef CONFIG_SND_CS46XX_NEW_DSP
 	err = snd_cs46xx_pcm_rear(chip, 1);
 	if (err < 0)
-		return err;
+		goto error;
 	err = snd_cs46xx_pcm_iec958(chip, 2);
 	if (err < 0)
-		return err;
+		goto error;
 #endif
 	err = snd_cs46xx_mixer(chip, 2);
 	if (err < 0)
-		return err;
+		goto error;
 #ifdef CONFIG_SND_CS46XX_NEW_DSP
 	if (chip->nr_ac97_codecs ==2) {
 		err = snd_cs46xx_pcm_center_lfe(chip, 3);
 		if (err < 0)
-			return err;
+			goto error;
 	}
 #endif
 	err = snd_cs46xx_midi(chip, 0);
 	if (err < 0)
-		return err;
+		goto error;
 	err = snd_cs46xx_start_dsp(chip);
 	if (err < 0)
-		return err;
+		goto error;
 
 	snd_cs46xx_gameport(chip);
 
@@ -117,11 +117,15 @@
 
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver cs46xx_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/cs5535audio/cs5535audio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/cs5535audio/cs5535audio.c
@@ -281,8 +281,8 @@
 	return 0;
 }
 
-static int snd_cs5535audio_probe(struct pci_dev *pci,
-				 const struct pci_device_id *pci_id)
+static int __snd_cs5535audio_probe(struct pci_dev *pci,
+				   const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -331,6 +331,12 @@
 	return 0;
 }
 
+static int snd_cs5535audio_probe(struct pci_dev *pci,
+				 const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_cs5535audio_probe(pci, pci_id));
+}
+
 static struct pci_driver cs5535audio_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_cs5535audio_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/ctamixer.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/ctamixer.c
@@ -23,16 +23,15 @@
 
 #define BLANK_SLOT		4094
 
-static int amixer_master(struct rsc *rsc)
+static void amixer_master(struct rsc *rsc)
 {
 	rsc->conj = 0;
-	return rsc->idx = container_of(rsc, struct amixer, rsc)->idx[0];
+	rsc->idx = container_of(rsc, struct amixer, rsc)->idx[0];
 }
 
-static int amixer_next_conj(struct rsc *rsc)
+static void amixer_next_conj(struct rsc *rsc)
 {
 	rsc->conj++;
-	return container_of(rsc, struct amixer, rsc)->idx[rsc->conj];
 }
 
 static int amixer_index(const struct rsc *rsc)
@@ -331,16 +330,15 @@
 
 /* SUM resource management */
 
-static int sum_master(struct rsc *rsc)
+static void sum_master(struct rsc *rsc)
 {
 	rsc->conj = 0;
-	return rsc->idx = container_of(rsc, struct sum, rsc)->idx[0];
+	rsc->idx = container_of(rsc, struct sum, rsc)->idx[0];
 }
 
-static int sum_next_conj(struct rsc *rsc)
+static void sum_next_conj(struct rsc *rsc)
 {
 	rsc->conj++;
-	return container_of(rsc, struct sum, rsc)->idx[rsc->conj];
 }
 
 static int sum_index(const struct rsc *rsc)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/ctatc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/ctatc.c
@@ -36,6 +36,7 @@
 			    | ((IEC958_AES3_CON_FS_48000) << 24))
 
 static const struct snd_pci_quirk subsys_20k1_list[] = {
+	SND_PCI_QUIRK(PCI_VENDOR_ID_CREATIVE, 0x0021, "SB046x", CTSB046X),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_CREATIVE, 0x0022, "SB055x", CTSB055X),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_CREATIVE, 0x002f, "SB055x", CTSB055X),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_CREATIVE, 0x0029, "SB073x", CTSB073X),
@@ -64,6 +65,7 @@
 
 static const char *ct_subsys_name[NUM_CTCARDS] = {
 	/* 20k1 models */
+	[CTSB046X]	= "SB046x",
 	[CTSB055X]	= "SB055x",
 	[CTSB073X]	= "SB073x",
 	[CTUAA]		= "UAA",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/ctdaio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/ctdaio.c
@@ -51,12 +51,12 @@
 	[SPDIFIO] = {.left = 0x05, .right = 0x85},
 };
 
-static int daio_master(struct rsc *rsc)
+static void daio_master(struct rsc *rsc)
 {
 	/* Actually, this is not the resource index of DAIO.
 	 * For DAO, it is the input mapper index. And, for DAI,
 	 * it is the output time-slot index. */
-	return rsc->conj = rsc->idx;
+	rsc->conj = rsc->idx;
 }
 
 static int daio_index(const struct rsc *rsc)
@@ -64,19 +64,19 @@
 	return rsc->conj;
 }
 
-static int daio_out_next_conj(struct rsc *rsc)
+static void daio_out_next_conj(struct rsc *rsc)
 {
-	return rsc->conj += 2;
+	rsc->conj += 2;
 }
 
-static int daio_in_next_conj_20k1(struct rsc *rsc)
+static void daio_in_next_conj_20k1(struct rsc *rsc)
 {
-	return rsc->conj += 0x200;
+	rsc->conj += 0x200;
 }
 
-static int daio_in_next_conj_20k2(struct rsc *rsc)
+static void daio_in_next_conj_20k2(struct rsc *rsc)
 {
-	return rsc->conj += 0x100;
+	rsc->conj += 0x100;
 }
 
 static const struct rsc_ops daio_out_rsc_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/cthardware.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/cthardware.h
@@ -26,8 +26,9 @@
 
 enum CTCARDS {
 	/* 20k1 models */
+	CTSB046X,
+	CT20K1_MODEL_FIRST = CTSB046X,
 	CTSB055X,
-	CT20K1_MODEL_FIRST = CTSB055X,
 	CTSB073X,
 	CTUAA,
 	CT20K1_UNKNOWN,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/ctresource.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/ctresource.c
@@ -109,18 +109,17 @@
     return (rsc->conj << 4) + offset_in_audio_slot_block[rsc->type];
 }
 
-static int rsc_next_conj(struct rsc *rsc)
+static void rsc_next_conj(struct rsc *rsc)
 {
 	unsigned int i;
 	for (i = 0; (i < 8) && (!(rsc->msr & (0x1 << i))); )
 		i++;
 	rsc->conj += (AUDIO_SLOT_BLOCK_NUM >> i);
-	return rsc->conj;
 }
 
-static int rsc_master(struct rsc *rsc)
+static void rsc_master(struct rsc *rsc)
 {
-	return rsc->conj = rsc->idx;
+	rsc->conj = rsc->idx;
 }
 
 static const struct rsc_ops rsc_generic_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/ctresource.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/ctresource.h
@@ -39,8 +39,8 @@
 };
 
 struct rsc_ops {
-	int (*master)(struct rsc *rsc);	/* Move to master resource */
-	int (*next_conj)(struct rsc *rsc); /* Move to next conjugate resource */
+	void (*master)(struct rsc *rsc); /* Move to master resource */
+	void (*next_conj)(struct rsc *rsc); /* Move to next conjugate resource */
 	int (*index)(const struct rsc *rsc); /* Return the index of resource */
 	/* Return the output slot number */
 	int (*output_slot)(const struct rsc *rsc);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ctxfi/ctsrc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ctxfi/ctsrc.c
@@ -590,16 +590,15 @@
 
 /* SRCIMP resource manager operations */
 
-static int srcimp_master(struct rsc *rsc)
+static void srcimp_master(struct rsc *rsc)
 {
 	rsc->conj = 0;
-	return rsc->idx = container_of(rsc, struct srcimp, rsc)->idx[0];
+	rsc->idx = container_of(rsc, struct srcimp, rsc)->idx[0];
 }
 
-static int srcimp_next_conj(struct rsc *rsc)
+static void srcimp_next_conj(struct rsc *rsc)
 {
 	rsc->conj++;
-	return container_of(rsc, struct srcimp, rsc)->idx[rsc->conj];
 }
 
 static int srcimp_index(const struct rsc *rsc)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/echoaudio/echoaudio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/echoaudio/echoaudio.c
@@ -1970,8 +1970,8 @@
 }
 
 /* constructor */
-static int snd_echo_probe(struct pci_dev *pci,
-			  const struct pci_device_id *pci_id)
+static int __snd_echo_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2139,6 +2139,11 @@
 	return 0;
 }
 
+static int snd_echo_probe(struct pci_dev *pci,
+			  const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_echo_probe(pci, pci_id));
+}
 
 
 #if defined(CONFIG_PM_SLEEP)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/emu10k1/emu10k1x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/emu10k1/emu10k1x.c
@@ -1491,8 +1491,8 @@
 	return 0;
 }
 
-static int snd_emu10k1x_probe(struct pci_dev *pci,
-			      const struct pci_device_id *pci_id)
+static int __snd_emu10k1x_probe(struct pci_dev *pci,
+				const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -1554,6 +1554,12 @@
 	return 0;
 }
 
+static int snd_emu10k1x_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_emu10k1x_probe(pci, pci_id));
+}
+
 // PCI IDs
 static const struct pci_device_id snd_emu10k1x_ids[] = {
 	{ PCI_VDEVICE(CREATIVE, 0x0006), 0 },	/* Dell OEM version (EMU10K1) */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/emu10k1/emufx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/emu10k1/emufx.c
@@ -1563,14 +1563,8 @@
 	gpr += 2;
 
 	/* Master volume (will be renamed later) */
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+0+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+0+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+1+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+1+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+2+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+2+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+3+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+3+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+4+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+4+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+5+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+5+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+6+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+6+SND_EMU10K1_PLAYBACK_CHANNELS));
-	A_OP(icode, &ptr, iMAC0, A_GPR(playback+7+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+7+SND_EMU10K1_PLAYBACK_CHANNELS));
+	for (z = 0; z < 8; z++)
+		A_OP(icode, &ptr, iMAC0, A_GPR(playback+z+SND_EMU10K1_PLAYBACK_CHANNELS), A_C_00000000, A_GPR(gpr), A_GPR(playback+z+SND_EMU10K1_PLAYBACK_CHANNELS));
 	snd_emu10k1_init_mono_control(&controls[nctl++], "Wave Master Playback Volume", gpr, 0);
 	gpr += 2;
 
@@ -1654,102 +1648,14 @@
 			dev_dbg(emu->card->dev, "emufx.c: gpr=0x%x, tmp=0x%x\n",
 			       gpr, tmp);
 			*/
-			/* For the EMU1010: How to get 32bit values from the DSP. High 16bits into L, low 16bits into R. */
-			/* A_P16VIN(0) is delayed by one sample,
-			 * so all other A_P16VIN channels will need to also be delayed
-			 */
-			/* Left ADC in. 1 of 2 */
 			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_P16VIN(0x0), A_FXBUS2(0) );
-			/* Right ADC in 1 of 2 */
-			gpr_map[gpr++] = 0x00000000;
-			/* Delaying by one sample: instead of copying the input
-			 * value A_P16VIN to output A_FXBUS2 as in the first channel,
-			 * we use an auxiliary register, delaying the value by one
-			 * sample
-			 */
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(2) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x1), A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(4) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x2), A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(6) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x3), A_C_00000000, A_C_00000000);
-			/* For 96kHz mode */
-			/* Left ADC in. 2 of 2 */
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(0x8) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x4), A_C_00000000, A_C_00000000);
-			/* Right ADC in 2 of 2 */
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(0xa) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x5), A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(0xc) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x6), A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr - 1), A_FXBUS2(0xe) );
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x7), A_C_00000000, A_C_00000000);
-			/* Pavel Hofman - we still have voices, A_FXBUS2s, and
-			 * A_P16VINs available -
-			 * let's add 8 more capture channels - total of 16
-			 */
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x10));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x8),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x12));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0x9),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x14));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0xa),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x16));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0xb),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x18));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0xc),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x1a));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0xd),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x1c));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0xe),
-			     A_C_00000000, A_C_00000000);
-			gpr_map[gpr++] = 0x00000000;
-			snd_emu10k1_audigy_dsp_convert_32_to_2x16(icode, &ptr, tmp,
-								  bit_shifter16,
-								  A_GPR(gpr - 1),
-								  A_FXBUS2(0x1e));
-			A_OP(icode, &ptr, iACC3, A_GPR(gpr - 1), A_P16VIN(0xf),
-			     A_C_00000000, A_C_00000000);
+			/* A_P16VIN(0) is delayed by one sample, so all other A_P16VIN channels
+			 * will need to also be delayed; we use an auxiliary register for that. */
+			for (z = 1; z < 0x10; z++) {
+				snd_emu10k1_audigy_dsp_convert_32_to_2x16( icode, &ptr, tmp, bit_shifter16, A_GPR(gpr), A_FXBUS2(z * 2) );
+				A_OP(icode, &ptr, iACC3, A_GPR(gpr), A_P16VIN(z), A_C_00000000, A_C_00000000);
+				gpr_map[gpr++] = 0x00000000;
+			}
 		}
 
 #if 0
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/emu10k1/emupcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/emu10k1/emupcm.c
@@ -124,7 +124,7 @@
 	epcm->voices[0]->epcm = epcm;
 	if (voices > 1) {
 		for (i = 1; i < voices; i++) {
-			epcm->voices[i] = &epcm->emu->voices[epcm->voices[0]->number + i];
+			epcm->voices[i] = &epcm->emu->voices[(epcm->voices[0]->number + i) % NUM_G];
 			epcm->voices[i]->epcm = epcm;
 		}
 	}
@@ -1236,7 +1236,7 @@
 {
 	struct snd_emu10k1 *emu = snd_pcm_substream_chip(substream);
 
-	emu->capture_interrupt = NULL;
+	emu->capture_mic_interrupt = NULL;
 	emu->pcm_capture_mic_substream = NULL;
 	return 0;
 }
@@ -1344,7 +1344,7 @@
 {
 	struct snd_emu10k1 *emu = snd_pcm_substream_chip(substream);
 
-	emu->capture_interrupt = NULL;
+	emu->capture_efx_interrupt = NULL;
 	emu->pcm_capture_efx_substream = NULL;
 	return 0;
 }
@@ -1781,17 +1781,21 @@
 	struct snd_kcontrol *kctl;
 	int err;
 
-	err = snd_pcm_new(emu->card, "emu10k1 efx", device, 8, 1, &pcm);
+	err = snd_pcm_new(emu->card, "emu10k1 efx", device, emu->audigy ? 0 : 8, 1, &pcm);
 	if (err < 0)
 		return err;
 
 	pcm->private_data = emu;
 
-	snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_emu10k1_fx8010_playback_ops);
+	if (!emu->audigy)
+		snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_emu10k1_fx8010_playback_ops);
 	snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_emu10k1_capture_efx_ops);
 
 	pcm->info_flags = 0;
-	strcpy(pcm->name, "Multichannel Capture/PT Playback");
+	if (emu->audigy)
+		strcpy(pcm->name, "Multichannel Capture");
+	else
+		strcpy(pcm->name, "Multichannel Capture/PT Playback");
 	emu->pcm_efx = pcm;
 
 	/* EFX capture - record the "FXBUS2" channels, by default we connect the EXTINs 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ens1370.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ens1370.c
@@ -2304,8 +2304,8 @@
 	return IRQ_HANDLED;
 }
 
-static int snd_audiopci_probe(struct pci_dev *pci,
-			      const struct pci_device_id *pci_id)
+static int __snd_audiopci_probe(struct pci_dev *pci,
+				const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2369,6 +2369,12 @@
 	return 0;
 }
 
+static int snd_audiopci_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_audiopci_probe(pci, pci_id));
+}
+
 static struct pci_driver ens137x_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_audiopci_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/es1938.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/es1938.c
@@ -1716,8 +1716,8 @@
 }
        
 
-static int snd_es1938_probe(struct pci_dev *pci,
-			    const struct pci_device_id *pci_id)
+static int __snd_es1938_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -1796,6 +1796,12 @@
 	return 0;
 }
 
+static int snd_es1938_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_es1938_probe(pci, pci_id));
+}
+
 static struct pci_driver es1938_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_es1938_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/es1968.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/es1968.c
@@ -2741,8 +2741,8 @@
 
 /*
  */
-static int snd_es1968_probe(struct pci_dev *pci,
-			    const struct pci_device_id *pci_id)
+static int __snd_es1968_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2848,6 +2848,12 @@
 	return 0;
 }
 
+static int snd_es1968_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_es1968_probe(pci, pci_id));
+}
+
 static struct pci_driver es1968_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_es1968_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/fm801.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/fm801.c
@@ -1268,8 +1268,8 @@
 	return 0;
 }
 
-static int snd_card_fm801_probe(struct pci_dev *pci,
-				const struct pci_device_id *pci_id)
+static int __snd_card_fm801_probe(struct pci_dev *pci,
+				  const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -1333,6 +1333,12 @@
 	return 0;
 }
 
+static int snd_card_fm801_probe(struct pci_dev *pci,
+				const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_card_fm801_probe(pci, pci_id));
+}
+
 #ifdef CONFIG_PM_SLEEP
 static const unsigned char saved_regs[] = {
 	FM801_PCM_VOL, FM801_I2S_VOL, FM801_FM_VOL, FM801_REC_SRC,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/Kconfig
@@ -91,6 +91,35 @@
 	  start up.  The "patch" file can be specified via patch module
 	  option, such as patch=hda-init.
 
+config SND_HDA_SCODEC_CS35L41
+	tristate
+
+config SND_HDA_SCODEC_CS35L41_I2C
+	tristate "Build CS35L41 HD-audio side codec support for I2C Bus"
+	depends on ACPI
+	select SND_HDA_GENERIC
+	select SND_SOC_CS35L41_LIB
+	select SND_HDA_SCODEC_CS35L41
+	help
+	  Say Y or M here to include CS35L41 I2C HD-audio side codec support
+	  in snd-hda-intel driver, such as ALC287.
+
+comment "Set to Y if you want auto-loading the side codec driver"
+	depends on SND_HDA=y && SND_HDA_SCODEC_CS35L41_I2C=m
+
+config SND_HDA_SCODEC_CS35L41_SPI
+	tristate "Build CS35L41 HD-audio codec support for SPI Bus"
+	depends on ACPI
+	select SND_HDA_GENERIC
+	select SND_SOC_CS35L41_LIB
+	select SND_HDA_SCODEC_CS35L41
+	help
+	  Say Y or M here to include CS35L41 SPI HD-audio side codec support
+	  in snd-hda-intel driver, such as ALC287.
+
+comment "Set to Y if you want auto-loading the side codec driver"
+	depends on SND_HDA=y && SND_HDA_SCODEC_CS35L41_SPI=m
+
 config SND_HDA_CODEC_REALTEK
 	tristate "Build Realtek HD-audio codec support"
 	select SND_HDA_GENERIC
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/Makefile
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/Makefile
@@ -27,6 +27,11 @@
 snd-hda-codec-via-objs :=	patch_via.o
 snd-hda-codec-hdmi-objs :=	patch_hdmi.o hda_eld.o
 
+# side codecs
+snd-hda-scodec-cs35l41-objs :=		cs35l41_hda.o
+snd-hda-scodec-cs35l41-i2c-objs :=	cs35l41_hda_i2c.o
+snd-hda-scodec-cs35l41-spi-objs :=	cs35l41_hda_spi.o
+
 # common driver
 obj-$(CONFIG_SND_HDA) := snd-hda-codec.o
 
@@ -45,6 +50,11 @@
 obj-$(CONFIG_SND_HDA_CODEC_VIA) += snd-hda-codec-via.o
 obj-$(CONFIG_SND_HDA_CODEC_HDMI) += snd-hda-codec-hdmi.o
 
+# side codecs
+obj-$(CONFIG_SND_HDA_SCODEC_CS35L41) += snd-hda-scodec-cs35l41.o
+obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_I2C) += snd-hda-scodec-cs35l41-i2c.o
+obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_SPI) += snd-hda-scodec-cs35l41-spi.o
+
 # this must be the last entry after codec drivers;
 # otherwise the codec patches won't be hooked before the PCI probe
 # when built in kernel
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/cs35l41_hda.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/cs35l41_hda.c
@@ -0,0 +1,542 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// CS35l41 ALSA HDA audio driver
+//
+// Copyright 2021 Cirrus Logic, Inc.
+//
+// Author: Lucas Tanure <tanureal@opensource.cirrus.com>
+
+#include <linux/acpi.h>
+#include <linux/module.h>
+#include <sound/hda_codec.h>
+#include "hda_local.h"
+#include "hda_auto_parser.h"
+#include "hda_jack.h"
+#include "hda_generic.h"
+#include "hda_component.h"
+#include "cs35l41_hda.h"
+
+static const struct reg_sequence cs35l41_hda_config[] = {
+	{ CS35L41_PLL_CLK_CTRL,		0x00000430 }, // 3200000Hz, BCLK Input, PLL_REFCLK_EN = 1
+	{ CS35L41_GLOBAL_CLK_CTRL,	0x00000003 }, // GLOBAL_FS = 48 kHz
+	{ CS35L41_SP_ENABLES,		0x00010000 }, // ASP_RX1_EN = 1
+	{ CS35L41_SP_RATE_CTRL,		0x00000021 }, // ASP_BCLK_FREQ = 3.072 MHz
+	{ CS35L41_SP_FORMAT,		0x20200200 }, // 24 bits, I2S, BCLK Slave, FSYNC Slave
+	{ CS35L41_DAC_PCM1_SRC,		0x00000008 }, // DACPCM1_SRC = ASPRX1
+	{ CS35L41_AMP_DIG_VOL_CTRL,	0x00000000 }, // AMP_VOL_PCM  0.0 dB
+	{ CS35L41_AMP_GAIN_CTRL,	0x00000084 }, // AMP_GAIN_PCM 4.5 dB
+	{ CS35L41_PWR_CTRL2,		0x00000001 }, // AMP_EN = 1
+};
+
+static const struct reg_sequence cs35l41_hda_start_bst[] = {
+	{ CS35L41_PWR_CTRL2,		0x00000021 }, // BST_EN = 10, AMP_EN = 1
+	{ CS35L41_PWR_CTRL1,		0x00000001, 3000}, // set GLOBAL_EN = 1
+};
+
+static const struct reg_sequence cs35l41_hda_stop_bst[] = {
+	{ CS35L41_PWR_CTRL1,		0x00000000, 3000}, // set GLOBAL_EN = 0
+};
+
+// only on amps where GPIO1 is used to control ext. VSPK switch
+static const struct reg_sequence cs35l41_start_ext_vspk[] = {
+	{ 0x00000040,			0x00000055 },
+	{ 0x00000040,			0x000000AA },
+	{ 0x00007438,			0x00585941 },
+	{ 0x00007414,			0x08C82222 },
+	{ 0x0000742C,			0x00000009 },
+	{ 0x00011008,			0x00008001 },
+	{ 0x0000742C,			0x0000000F },
+	{ 0x0000742C,			0x00000079 },
+	{ 0x00007438,			0x00585941 },
+	{ CS35L41_PWR_CTRL1,		0x00000001, 3000}, // set GLOBAL_EN = 1
+	{ 0x0000742C,			0x000000F9 },
+	{ 0x00007438,			0x00580941 },
+	{ 0x00000040,			0x000000CC },
+	{ 0x00000040,			0x00000033 },
+};
+
+//only on amps where GPIO1 is used to control ext. VSPK switch
+static const struct reg_sequence cs35l41_stop_ext_vspk[] = {
+	{ 0x00000040,			0x00000055 },
+	{ 0x00000040,			0x000000AA },
+	{ 0x00007438,			0x00585941 },
+	{ 0x00002014,			0x00000000, 3000}, // set GLOBAL_EN = 0
+	{ 0x0000742C,			0x00000009 },
+	{ 0x00007438,			0x00580941 },
+	{ 0x00011008,			0x00000001 },
+	{ 0x0000393C,			0x000000C0, 6000},
+	{ 0x0000393C,			0x00000000 },
+	{ 0x00007414,			0x00C82222 },
+	{ 0x0000742C,			0x00000000 },
+	{ 0x00000040,			0x000000CC },
+	{ 0x00000040,			0x00000033 },
+};
+
+static const struct reg_sequence cs35l41_safe_to_active[] = {
+	{ 0x00000040,			0x00000055 },
+	{ 0x00000040,			0x000000AA },
+	{ 0x0000742C,			0x0000000F },
+	{ 0x0000742C,			0x00000079 },
+	{ 0x00007438,			0x00585941 },
+	{ CS35L41_PWR_CTRL1,		0x00000001, 2000 }, // GLOBAL_EN = 1
+	{ 0x0000742C,			0x000000F9 },
+	{ 0x00007438,			0x00580941 },
+	{ 0x00000040,			0x000000CC },
+	{ 0x00000040,			0x00000033 },
+};
+
+static const struct reg_sequence cs35l41_active_to_safe[] = {
+	{ 0x00000040,			0x00000055 },
+	{ 0x00000040,			0x000000AA },
+	{ 0x00007438,			0x00585941 },
+	{ CS35L41_AMP_DIG_VOL_CTRL,	0x0000A678 }, // AMP_VOL_PCM Mute
+	{ CS35L41_PWR_CTRL2,		0x00000000 }, // AMP_EN = 0
+	{ CS35L41_PWR_CTRL1,		0x00000000 },
+	{ 0x0000742C,			0x00000009, 2000 },
+	{ 0x00007438,			0x00580941 },
+	{ 0x00000040,			0x000000CC },
+	{ 0x00000040,			0x00000033 },
+};
+
+static const struct reg_sequence cs35l41_reset_to_safe[] = {
+	{ 0x00000040,			0x00000055 },
+	{ 0x00000040,			0x000000AA },
+	{ 0x00007438,			0x00585941 },
+	{ 0x00007414,			0x08C82222 },
+	{ 0x0000742C,			0x00000009 },
+	{ 0x00000040,			0x000000CC },
+	{ 0x00000040,			0x00000033 },
+};
+
+static const struct cs35l41_hda_reg_sequence cs35l41_hda_reg_seq_no_bst = {
+	.probe		= cs35l41_reset_to_safe,
+	.num_probe	= ARRAY_SIZE(cs35l41_reset_to_safe),
+	.open		= cs35l41_hda_config,
+	.num_open	= ARRAY_SIZE(cs35l41_hda_config),
+	.prepare	= cs35l41_safe_to_active,
+	.num_prepare	= ARRAY_SIZE(cs35l41_safe_to_active),
+	.cleanup	= cs35l41_active_to_safe,
+	.num_cleanup	= ARRAY_SIZE(cs35l41_active_to_safe),
+};
+
+static const struct cs35l41_hda_reg_sequence cs35l41_hda_reg_seq_ext_bst = {
+	.open		= cs35l41_hda_config,
+	.num_open	= ARRAY_SIZE(cs35l41_hda_config),
+	.prepare	= cs35l41_start_ext_vspk,
+	.num_prepare	= ARRAY_SIZE(cs35l41_start_ext_vspk),
+	.cleanup	= cs35l41_stop_ext_vspk,
+	.num_cleanup	= ARRAY_SIZE(cs35l41_stop_ext_vspk),
+};
+
+static const struct cs35l41_hda_reg_sequence cs35l41_hda_reg_seq_int_bst = {
+	.open		= cs35l41_hda_config,
+	.num_open	= ARRAY_SIZE(cs35l41_hda_config),
+	.prepare	= cs35l41_hda_start_bst,
+	.num_prepare	= ARRAY_SIZE(cs35l41_hda_start_bst),
+	.cleanup	= cs35l41_hda_stop_bst,
+	.num_cleanup	= ARRAY_SIZE(cs35l41_hda_stop_bst),
+};
+
+static void cs35l41_hda_playback_hook(struct device *dev, int action)
+{
+	struct cs35l41_hda *cs35l41 = dev_get_drvdata(dev);
+	const struct cs35l41_hda_reg_sequence *reg_seq = cs35l41->reg_seq;
+	struct regmap *reg = cs35l41->regmap;
+	int ret = 0;
+
+	switch (action) {
+	case HDA_GEN_PCM_ACT_OPEN:
+		if (reg_seq->open)
+			ret = regmap_multi_reg_write(reg, reg_seq->open, reg_seq->num_open);
+		break;
+	case HDA_GEN_PCM_ACT_PREPARE:
+		if (reg_seq->prepare)
+			ret = regmap_multi_reg_write(reg, reg_seq->prepare, reg_seq->num_prepare);
+		break;
+	case HDA_GEN_PCM_ACT_CLEANUP:
+		if (reg_seq->cleanup)
+			ret = regmap_multi_reg_write(reg, reg_seq->cleanup, reg_seq->num_cleanup);
+		break;
+	case HDA_GEN_PCM_ACT_CLOSE:
+		if (reg_seq->close)
+			ret = regmap_multi_reg_write(reg, reg_seq->close, reg_seq->num_close);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	if (ret)
+		dev_warn(cs35l41->dev, "Failed to apply multi reg write: %d\n", ret);
+}
+
+static int cs35l41_hda_channel_map(struct device *dev, unsigned int tx_num, unsigned int *tx_slot,
+				    unsigned int rx_num, unsigned int *rx_slot)
+{
+	struct cs35l41_hda *cs35l41 = dev_get_drvdata(dev);
+
+	return cs35l41_set_channels(cs35l41->dev, cs35l41->regmap, tx_num, tx_slot, rx_num,
+				    rx_slot);
+}
+
+static int cs35l41_hda_bind(struct device *dev, struct device *master, void *master_data)
+{
+	struct cs35l41_hda *cs35l41 = dev_get_drvdata(dev);
+	struct hda_component *comps = master_data;
+
+	if (!comps || cs35l41->index < 0 || cs35l41->index >= HDA_MAX_COMPONENTS)
+		return -EINVAL;
+
+	comps = &comps[cs35l41->index];
+	if (comps->dev)
+		return -EBUSY;
+
+	comps->dev = dev;
+	strscpy(comps->name, dev_name(dev), sizeof(comps->name));
+	comps->playback_hook = cs35l41_hda_playback_hook;
+	comps->set_channel_map = cs35l41_hda_channel_map;
+
+	return 0;
+}
+
+static void cs35l41_hda_unbind(struct device *dev, struct device *master, void *master_data)
+{
+	struct cs35l41_hda *cs35l41 = dev_get_drvdata(dev);
+	struct hda_component *comps = master_data;
+
+	if (comps[cs35l41->index].dev == dev)
+		memset(&comps[cs35l41->index], 0, sizeof(*comps));
+}
+
+static const struct component_ops cs35l41_hda_comp_ops = {
+	.bind = cs35l41_hda_bind,
+	.unbind = cs35l41_hda_unbind,
+};
+
+static int cs35l41_hda_apply_properties(struct cs35l41_hda *cs35l41,
+					const struct cs35l41_hda_hw_config *hw_cfg)
+{
+	bool internal_boost = false;
+	int ret;
+
+	if (!hw_cfg) {
+		cs35l41->reg_seq = &cs35l41_hda_reg_seq_no_bst;
+		return 0;
+	}
+
+	if (hw_cfg->bst_ind || hw_cfg->bst_cap || hw_cfg->bst_ipk)
+		internal_boost = true;
+
+	switch (hw_cfg->gpio1_func) {
+	case CS35L41_NOT_USED:
+		break;
+	case CS35l41_VSPK_SWITCH:
+		regmap_update_bits(cs35l41->regmap, CS35L41_GPIO_PAD_CONTROL,
+				   CS35L41_GPIO1_CTRL_MASK, 1 << CS35L41_GPIO1_CTRL_SHIFT);
+		break;
+	case CS35l41_SYNC:
+		regmap_update_bits(cs35l41->regmap, CS35L41_GPIO_PAD_CONTROL,
+				   CS35L41_GPIO1_CTRL_MASK, 2 << CS35L41_GPIO1_CTRL_SHIFT);
+		break;
+	default:
+		dev_err(cs35l41->dev, "Invalid function %d for GPIO1\n", hw_cfg->gpio1_func);
+		return -EINVAL;
+	}
+
+	switch (hw_cfg->gpio2_func) {
+	case CS35L41_NOT_USED:
+		break;
+	case CS35L41_INTERRUPT:
+		regmap_update_bits(cs35l41->regmap, CS35L41_GPIO_PAD_CONTROL,
+				   CS35L41_GPIO2_CTRL_MASK, 2 << CS35L41_GPIO2_CTRL_SHIFT);
+		break;
+	default:
+		dev_err(cs35l41->dev, "Invalid function %d for GPIO2\n", hw_cfg->gpio2_func);
+		return -EINVAL;
+	}
+
+	if (internal_boost) {
+		cs35l41->reg_seq = &cs35l41_hda_reg_seq_int_bst;
+		if (!(hw_cfg->bst_ind && hw_cfg->bst_cap && hw_cfg->bst_ipk))
+			return -EINVAL;
+		ret = cs35l41_boost_config(cs35l41->dev, cs35l41->regmap,
+					   hw_cfg->bst_ind, hw_cfg->bst_cap, hw_cfg->bst_ipk);
+		if (ret)
+			return ret;
+	} else {
+		cs35l41->reg_seq = &cs35l41_hda_reg_seq_ext_bst;
+	}
+
+	return cs35l41_hda_channel_map(cs35l41->dev, 0, NULL, 1, (unsigned int *)&hw_cfg->spk_pos);
+}
+
+static struct cs35l41_hda_hw_config *cs35l41_hda_read_acpi(struct cs35l41_hda *cs35l41,
+							   const char *hid, int id)
+{
+	struct cs35l41_hda_hw_config *hw_cfg;
+	u32 values[HDA_MAX_COMPONENTS];
+	struct acpi_device *adev;
+	struct device *physdev;
+	char *property;
+	size_t nval;
+	int i, ret;
+
+	adev = acpi_dev_get_first_match_dev(hid, NULL, -1);
+	if (!adev) {
+		dev_err(cs35l41->dev, "Failed to find an ACPI device for %s\n", hid);
+		return ERR_PTR(-ENODEV);
+	}
+
+	physdev = get_device(acpi_get_first_physical_node(adev));
+	acpi_dev_put(adev);
+
+	property = "cirrus,dev-index";
+	ret = device_property_count_u32(physdev, property);
+	if (ret <= 0)
+		goto no_acpi_dsd;
+
+	if (ret > ARRAY_SIZE(values)) {
+		ret = -EINVAL;
+		goto err;
+	}
+	nval = ret;
+
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret)
+		goto err;
+
+	cs35l41->index = -1;
+	for (i = 0; i < nval; i++) {
+		if (values[i] == id) {
+			cs35l41->index = i;
+			break;
+		}
+	}
+	if (cs35l41->index == -1) {
+		dev_err(cs35l41->dev, "No index found in %s\n", property);
+		ret = -ENODEV;
+		goto err;
+	}
+
+	/* To use the same release code for all laptop variants we can't use devm_ version of
+	 * gpiod_get here, as CLSA010* don't have a fully functional bios with an _DSD node
+	 */
+	cs35l41->reset_gpio = fwnode_gpiod_get_index(&adev->fwnode, "reset", cs35l41->index,
+						     GPIOD_OUT_LOW, "cs35l41-reset");
+
+	hw_cfg = kzalloc(sizeof(*hw_cfg), GFP_KERNEL);
+	if (!hw_cfg) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	property = "cirrus,speaker-position";
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret)
+		goto err_free;
+	hw_cfg->spk_pos = values[cs35l41->index];
+
+	property = "cirrus,gpio1-func";
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret)
+		goto err_free;
+	hw_cfg->gpio1_func = values[cs35l41->index];
+
+	property = "cirrus,gpio2-func";
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret)
+		goto err_free;
+	hw_cfg->gpio2_func = values[cs35l41->index];
+
+	property = "cirrus,boost-peak-milliamp";
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret == 0)
+		hw_cfg->bst_ipk = values[cs35l41->index];
+
+	property = "cirrus,boost-ind-nanohenry";
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret == 0)
+		hw_cfg->bst_ind = values[cs35l41->index];
+
+	property = "cirrus,boost-cap-microfarad";
+	ret = device_property_read_u32_array(physdev, property, values, nval);
+	if (ret == 0)
+		hw_cfg->bst_cap = values[cs35l41->index];
+
+	put_device(physdev);
+
+	return hw_cfg;
+
+err_free:
+	kfree(hw_cfg);
+err:
+	put_device(physdev);
+	dev_err(cs35l41->dev, "Failed property %s: %d\n", property, ret);
+
+	return ERR_PTR(ret);
+
+no_acpi_dsd:
+	/*
+	 * Device CLSA0100 doesn't have _DSD so a gpiod_get by the label reset won't work.
+	 * And devices created by i2c-multi-instantiate don't have their device struct pointing to
+	 * the correct fwnode, so acpi_dev must be used here.
+	 * And devm functions expect that the device requesting the resource has the correct
+	 * fwnode.
+	 */
+	if (strncmp(hid, "CLSA0100", 8) != 0)
+		return ERR_PTR(-EINVAL);
+
+	/* check I2C address to assign the index */
+	cs35l41->index = id == 0x40 ? 0 : 1;
+	cs35l41->reset_gpio = gpiod_get_index(physdev, NULL, 0, GPIOD_OUT_HIGH);
+	cs35l41->vspk_always_on = true;
+	put_device(physdev);
+
+	return NULL;
+}
+
+int cs35l41_hda_probe(struct device *dev, const char *device_name, int id, int irq,
+		      struct regmap *regmap)
+{
+	unsigned int int_sts, regid, reg_revid, mtl_revid, chipid, int_status;
+	struct cs35l41_hda_hw_config *acpi_hw_cfg;
+	struct cs35l41_hda *cs35l41;
+	int ret;
+
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	cs35l41 = devm_kzalloc(dev, sizeof(*cs35l41), GFP_KERNEL);
+	if (!cs35l41)
+		return -ENOMEM;
+
+	cs35l41->dev = dev;
+	cs35l41->irq = irq;
+	cs35l41->regmap = regmap;
+	dev_set_drvdata(dev, cs35l41);
+
+	acpi_hw_cfg = cs35l41_hda_read_acpi(cs35l41, device_name, id);
+	if (IS_ERR(acpi_hw_cfg))
+		return PTR_ERR(acpi_hw_cfg);
+
+	if (IS_ERR(cs35l41->reset_gpio)) {
+		ret = PTR_ERR(cs35l41->reset_gpio);
+		cs35l41->reset_gpio = NULL;
+		if (ret == -EBUSY) {
+			dev_info(cs35l41->dev, "Reset line busy, assuming shared reset\n");
+		} else {
+			dev_err_probe(cs35l41->dev, ret, "Failed to get reset GPIO: %d\n", ret);
+			goto err;
+		}
+	}
+	if (cs35l41->reset_gpio) {
+		usleep_range(2000, 2100);
+		gpiod_set_value_cansleep(cs35l41->reset_gpio, 1);
+	}
+
+	usleep_range(2000, 2100);
+
+	ret = regmap_read_poll_timeout(cs35l41->regmap, CS35L41_IRQ1_STATUS4, int_status,
+				       int_status & CS35L41_OTP_BOOT_DONE, 1000, 100000);
+	if (ret) {
+		dev_err(cs35l41->dev, "Failed waiting for OTP_BOOT_DONE: %d\n", ret);
+		goto err;
+	}
+
+	ret = regmap_read(cs35l41->regmap, CS35L41_IRQ1_STATUS3, &int_sts);
+	if (ret || (int_sts & CS35L41_OTP_BOOT_ERR)) {
+		dev_err(cs35l41->dev, "OTP Boot status %x error: %d\n",
+			int_sts & CS35L41_OTP_BOOT_ERR, ret);
+		ret = -EIO;
+		goto err;
+	}
+
+	ret = regmap_read(cs35l41->regmap, CS35L41_DEVID, &regid);
+	if (ret) {
+		dev_err(cs35l41->dev, "Get Device ID failed: %d\n", ret);
+		goto err;
+	}
+
+	ret = regmap_read(cs35l41->regmap, CS35L41_REVID, &reg_revid);
+	if (ret) {
+		dev_err(cs35l41->dev, "Get Revision ID failed: %d\n", ret);
+		goto err;
+	}
+
+	mtl_revid = reg_revid & CS35L41_MTLREVID_MASK;
+
+	chipid = (mtl_revid % 2) ? CS35L41R_CHIP_ID : CS35L41_CHIP_ID;
+	if (regid != chipid) {
+		dev_err(cs35l41->dev, "CS35L41 Device ID (%X). Expected ID %X\n", regid, chipid);
+		ret = -ENODEV;
+		goto err;
+	}
+
+	ret = cs35l41_test_key_unlock(cs35l41->dev, cs35l41->regmap);
+	if (ret)
+		goto err;
+
+	ret = cs35l41_register_errata_patch(cs35l41->dev, cs35l41->regmap, reg_revid);
+	if (ret)
+		goto err;
+
+	ret = cs35l41_otp_unpack(cs35l41->dev, cs35l41->regmap);
+	if (ret) {
+		dev_err(cs35l41->dev, "OTP Unpack failed: %d\n", ret);
+		goto err;
+	}
+
+	ret = cs35l41_test_key_lock(cs35l41->dev, cs35l41->regmap);
+	if (ret)
+		goto err;
+
+	ret = cs35l41_hda_apply_properties(cs35l41, acpi_hw_cfg);
+	if (ret)
+		goto err;
+	kfree(acpi_hw_cfg);
+	acpi_hw_cfg = NULL;
+
+	if (cs35l41->reg_seq->probe) {
+		ret = regmap_multi_reg_write(cs35l41->regmap, cs35l41->reg_seq->probe,
+					     cs35l41->reg_seq->num_probe);
+		if (ret) {
+			dev_err(cs35l41->dev, "Fail to apply probe reg patch: %d\n", ret);
+			goto err;
+		}
+	}
+
+	ret = component_add(cs35l41->dev, &cs35l41_hda_comp_ops);
+	if (ret) {
+		dev_err(cs35l41->dev, "Register component failed: %d\n", ret);
+		goto err;
+	}
+
+	dev_info(cs35l41->dev, "Cirrus Logic CS35L41 (%x), Revision: %02X\n", regid, reg_revid);
+
+	return 0;
+
+err:
+	kfree(acpi_hw_cfg);
+	if (!cs35l41->vspk_always_on)
+		gpiod_set_value_cansleep(cs35l41->reset_gpio, 0);
+	gpiod_put(cs35l41->reset_gpio);
+
+	return ret;
+}
+EXPORT_SYMBOL_NS_GPL(cs35l41_hda_probe, SND_HDA_SCODEC_CS35L41);
+
+void cs35l41_hda_remove(struct device *dev)
+{
+	struct cs35l41_hda *cs35l41 = dev_get_drvdata(dev);
+
+	component_del(cs35l41->dev, &cs35l41_hda_comp_ops);
+
+	if (!cs35l41->vspk_always_on)
+		gpiod_set_value_cansleep(cs35l41->reset_gpio, 0);
+	gpiod_put(cs35l41->reset_gpio);
+}
+EXPORT_SYMBOL_NS_GPL(cs35l41_hda_remove, SND_HDA_SCODEC_CS35L41);
+
+MODULE_DESCRIPTION("CS35L41 HDA Driver");
+MODULE_AUTHOR("Lucas Tanure, Cirrus Logic Inc, <tanureal@opensource.cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/cs35l41_hda.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/cs35l41_hda.h
@@ -0,0 +1,69 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * CS35L41 ALSA HDA audio driver
+ *
+ * Copyright 2021 Cirrus Logic, Inc.
+ *
+ * Author: Lucas Tanure <tanureal@opensource.cirrus.com>
+ */
+
+#ifndef __CS35L41_HDA_H__
+#define __CS35L41_HDA_H__
+
+#include <linux/regulator/consumer.h>
+#include <linux/gpio/consumer.h>
+#include <linux/device.h>
+#include <sound/cs35l41.h>
+
+enum cs35l41_hda_spk_pos {
+	CS35l41_LEFT,
+	CS35l41_RIGHT,
+};
+
+enum cs35l41_hda_gpio_function {
+	CS35L41_NOT_USED,
+	CS35l41_VSPK_SWITCH,
+	CS35L41_INTERRUPT,
+	CS35l41_SYNC,
+};
+
+struct cs35l41_hda_reg_sequence {
+	const struct reg_sequence *probe;
+	unsigned int num_probe;
+	const struct reg_sequence *open;
+	unsigned int num_open;
+	const struct reg_sequence *prepare;
+	unsigned int num_prepare;
+	const struct reg_sequence *cleanup;
+	unsigned int num_cleanup;
+	const struct reg_sequence *close;
+	unsigned int num_close;
+};
+
+struct cs35l41_hda_hw_config {
+	unsigned int spk_pos;
+	unsigned int gpio1_func;
+	unsigned int gpio2_func;
+	int bst_ind;
+	int bst_ipk;
+	int bst_cap;
+};
+
+struct cs35l41_hda {
+	struct device *dev;
+	struct regmap *regmap;
+	struct gpio_desc *reset_gpio;
+	const struct cs35l41_hda_reg_sequence *reg_seq;
+
+	int irq;
+	int index;
+
+	/* Don't put the AMP in reset of VSPK can not be turned off */
+	bool vspk_always_on;
+};
+
+int cs35l41_hda_probe(struct device *dev, const char *device_name, int id, int irq,
+		      struct regmap *regmap);
+void cs35l41_hda_remove(struct device *dev);
+
+#endif /*__CS35L41_HDA_H__*/
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/cs35l41_hda_i2c.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/cs35l41_hda_i2c.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// cs35l41.c -- CS35l41 HDA I2C driver
+//
+// Copyright 2021 Cirrus Logic, Inc.
+//
+// Author: Lucas Tanure <tanureal@opensource.cirrus.com>
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/acpi.h>
+
+#include "cs35l41_hda.h"
+
+static int cs35l41_hda_i2c_probe(struct i2c_client *clt, const struct i2c_device_id *id)
+{
+	const char *device_name;
+
+	/* Compare against the device name so it works for I2C, normal ACPI
+	 * and for ACPI by i2c-multi-instantiate matching cases
+	 */
+	if (strstr(dev_name(&clt->dev), "CLSA0100"))
+		device_name = "CLSA0100";
+	else if (strstr(dev_name(&clt->dev), "CSC3551"))
+		device_name = "CSC3551";
+	else
+		return -ENODEV;
+
+	return cs35l41_hda_probe(&clt->dev, device_name, clt->addr, clt->irq,
+				 devm_regmap_init_i2c(clt, &cs35l41_regmap_i2c));
+}
+
+static int cs35l41_hda_i2c_remove(struct i2c_client *clt)
+{
+	cs35l41_hda_remove(&clt->dev);
+
+	return 0;
+}
+
+static const struct i2c_device_id cs35l41_hda_i2c_id[] = {
+	{ "cs35l41-hda", 0 },
+	{}
+};
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id cs35l41_acpi_hda_match[] = {
+	{"CLSA0100", 0 },
+	{"CSC3551", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, cs35l41_acpi_hda_match);
+#endif
+
+static struct i2c_driver cs35l41_i2c_driver = {
+	.driver = {
+		.name		= "cs35l41-hda",
+		.acpi_match_table = ACPI_PTR(cs35l41_acpi_hda_match),
+	},
+	.id_table	= cs35l41_hda_i2c_id,
+	.probe		= cs35l41_hda_i2c_probe,
+	.remove		= cs35l41_hda_i2c_remove,
+};
+module_i2c_driver(cs35l41_i2c_driver);
+
+MODULE_DESCRIPTION("HDA CS35L41 driver");
+MODULE_IMPORT_NS(SND_HDA_SCODEC_CS35L41);
+MODULE_AUTHOR("Lucas Tanure <tanureal@opensource.cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/cs35l41_hda_spi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/cs35l41_hda_spi.c
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// cs35l41.c -- CS35l41 HDA SPI driver
+//
+// Copyright 2021 Cirrus Logic, Inc.
+//
+// Author: Lucas Tanure <tanureal@opensource.cirrus.com>
+
+#include <linux/acpi.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+
+#include "cs35l41_hda.h"
+
+static int cs35l41_hda_spi_probe(struct spi_device *spi)
+{
+	const char *device_name;
+
+	/* Compare against the device name so it works for SPI, normal ACPI
+	 * and for ACPI by spi-multi-instantiate matching cases
+	 */
+	if (strstr(dev_name(&spi->dev), "CSC3551"))
+		device_name = "CSC3551";
+	else
+		return -ENODEV;
+
+	return cs35l41_hda_probe(&spi->dev, device_name, spi->chip_select, spi->irq,
+				 devm_regmap_init_spi(spi, &cs35l41_regmap_spi));
+}
+
+static int cs35l41_hda_spi_remove(struct spi_device *spi)
+{
+	cs35l41_hda_remove(&spi->dev);
+
+	return 0;
+}
+
+static const struct spi_device_id cs35l41_hda_spi_id[] = {
+	{ "cs35l41-hda", 0 },
+	{}
+};
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id cs35l41_acpi_hda_match[] = {
+	{ "CSC3551", 0 },
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, cs35l41_acpi_hda_match);
+#endif
+
+static struct spi_driver cs35l41_spi_driver = {
+	.driver = {
+		.name		= "cs35l41_hda",
+		.acpi_match_table = ACPI_PTR(cs35l41_acpi_hda_match),
+	},
+	.id_table	= cs35l41_hda_spi_id,
+	.probe		= cs35l41_hda_spi_probe,
+	.remove		= cs35l41_hda_spi_remove,
+};
+module_spi_driver(cs35l41_spi_driver);
+
+MODULE_DESCRIPTION("HDA CS35L41 driver");
+MODULE_IMPORT_NS(SND_HDA_SCODEC_CS35L41);
+MODULE_AUTHOR("Lucas Tanure <tanureal@opensource.cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_auto_parser.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_auto_parser.c
@@ -823,7 +823,7 @@
 		snd_hda_set_pin_ctl_cache(codec, cfg->nid, cfg->val);
 }
 
-static void apply_fixup(struct hda_codec *codec, int id, int action, int depth)
+void __snd_hda_apply_fixup(struct hda_codec *codec, int id, int action, int depth)
 {
 	const char *modelname = codec->fixup_name;
 
@@ -833,7 +833,7 @@
 		if (++depth > 10)
 			break;
 		if (fix->chained_before)
-			apply_fixup(codec, fix->chain_id, action, depth + 1);
+			__snd_hda_apply_fixup(codec, fix->chain_id, action, depth + 1);
 
 		switch (fix->type) {
 		case HDA_FIXUP_PINS:
@@ -874,6 +874,7 @@
 		id = fix->chain_id;
 	}
 }
+EXPORT_SYMBOL_GPL(__snd_hda_apply_fixup);
 
 /**
  * snd_hda_apply_fixup - Apply the fixup chain with the given action
@@ -883,7 +884,7 @@
 void snd_hda_apply_fixup(struct hda_codec *codec, int action)
 {
 	if (codec->fixup_list)
-		apply_fixup(codec, codec->fixup_id, action, 0);
+		__snd_hda_apply_fixup(codec, codec->fixup_id, action, 0);
 }
 EXPORT_SYMBOL_GPL(snd_hda_apply_fixup);
 
@@ -985,7 +986,7 @@
 	int id = HDA_FIXUP_ID_NOT_SET;
 	const char *name = NULL;
 	const char *type = NULL;
-	int vendor, device;
+	unsigned int vendor, device;
 
 	if (codec->fixup_id != HDA_FIXUP_ID_NOT_SET)
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_beep.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_beep.c
@@ -118,6 +118,12 @@
 	return 0;
 }
 
+static void turn_on_beep(struct hda_beep *beep)
+{
+	if (beep->keep_power_at_enable)
+		snd_hda_power_up_pm(beep->codec);
+}
+
 static void turn_off_beep(struct hda_beep *beep)
 {
 	cancel_work_sync(&beep->beep_work);
@@ -125,6 +131,8 @@
 		/* turn off beep */
 		generate_tone(beep, 0);
 	}
+	if (beep->keep_power_at_enable)
+		snd_hda_power_down_pm(beep->codec);
 }
 
 /**
@@ -140,7 +148,9 @@
 	enable = !!enable;
 	if (beep->enabled != enable) {
 		beep->enabled = enable;
-		if (!enable)
+		if (enable)
+			turn_on_beep(beep);
+		else
 			turn_off_beep(beep);
 		return 1;
 	}
@@ -167,7 +177,8 @@
 		input_unregister_device(beep->dev);
 	else
 		input_free_device(beep->dev);
-	turn_off_beep(beep);
+	if (beep->enabled)
+		turn_off_beep(beep);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_beep.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_beep.h
@@ -25,6 +25,7 @@
 	unsigned int enabled:1;
 	unsigned int linear_tone:1;	/* linear tone for IDT/STAC codec */
 	unsigned int playing:1;
+	unsigned int keep_power_at_enable:1;	/* set by driver */
 	struct work_struct beep_work; /* scheduled task for beep event */
 	struct mutex mutex;
 	void (*power_hook)(struct hda_beep *beep, bool on);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_bind.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_bind.c
@@ -14,6 +14,7 @@
 #include <sound/core.h>
 #include <sound/hda_codec.h>
 #include "hda_local.h"
+#include "hda_jack.h"
 
 /*
  * find a matching codec id
@@ -143,6 +144,7 @@
 
  error:
 	snd_hda_codec_cleanup_for_unbind(codec);
+	codec->preset = NULL;
 	return err;
 }
 
@@ -156,9 +158,16 @@
 		return codec->bus->core.ext_ops->hdev_detach(&codec->core);
 	}
 
+	snd_hda_codec_disconnect_pcms(codec);
+	snd_hda_jack_tbl_disconnect(codec);
+	if (!refcount_dec_and_test(&codec->pcm_ref))
+		wait_event(codec->remove_sleep, !refcount_read(&codec->pcm_ref));
+	snd_power_sync_ref(codec->bus->card);
+
 	if (codec->patch_ops.free)
 		codec->patch_ops.free(codec);
 	snd_hda_codec_cleanup_for_unbind(codec);
+	codec->preset = NULL;
 	module_put(dev->driver->owner);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_codec.c
@@ -703,20 +703,10 @@
 /*
  * PCM device
  */
-static void release_pcm(struct kref *kref)
-{
-	struct hda_pcm *pcm = container_of(kref, struct hda_pcm, kref);
-
-	if (pcm->pcm)
-		snd_device_free(pcm->codec->card, pcm->pcm);
-	clear_bit(pcm->device, pcm->codec->bus->pcm_dev_bits);
-	kfree(pcm->name);
-	kfree(pcm);
-}
-
 void snd_hda_codec_pcm_put(struct hda_pcm *pcm)
 {
-	kref_put(&pcm->kref, release_pcm);
+	if (refcount_dec_and_test(&pcm->codec->pcm_ref))
+		wake_up(&pcm->codec->remove_sleep);
 }
 EXPORT_SYMBOL_GPL(snd_hda_codec_pcm_put);
 
@@ -731,7 +721,6 @@
 		return NULL;
 
 	pcm->codec = codec;
-	kref_init(&pcm->kref);
 	va_start(args, fmt);
 	pcm->name = kvasprintf(GFP_KERNEL, fmt, args);
 	va_end(args);
@@ -741,6 +730,7 @@
 	}
 
 	list_add_tail(&pcm->list, &codec->pcm_list_head);
+	refcount_inc(&codec->pcm_ref);
 	return pcm;
 }
 EXPORT_SYMBOL_GPL(snd_hda_codec_pcm_new);
@@ -748,15 +738,31 @@
 /*
  * codec destructor
  */
+void snd_hda_codec_disconnect_pcms(struct hda_codec *codec)
+{
+	struct hda_pcm *pcm;
+
+	list_for_each_entry(pcm, &codec->pcm_list_head, list) {
+		if (pcm->disconnected)
+			continue;
+		if (pcm->pcm)
+			snd_device_disconnect(codec->card, pcm->pcm);
+		snd_hda_codec_pcm_put(pcm);
+		pcm->disconnected = 1;
+	}
+}
+
 static void codec_release_pcms(struct hda_codec *codec)
 {
 	struct hda_pcm *pcm, *n;
 
 	list_for_each_entry_safe(pcm, n, &codec->pcm_list_head, list) {
-		list_del_init(&pcm->list);
+		list_del(&pcm->list);
 		if (pcm->pcm)
-			snd_device_disconnect(codec->card, pcm->pcm);
-		snd_hda_codec_pcm_put(pcm);
+			snd_device_free(pcm->codec->card, pcm->pcm);
+		clear_bit(pcm->device, pcm->codec->bus->pcm_dev_bits);
+		kfree(pcm->name);
+		kfree(pcm);
 	}
 }
 
@@ -769,6 +775,7 @@
 		codec->registered = 0;
 	}
 
+	snd_hda_codec_disconnect_pcms(codec);
 	cancel_delayed_work_sync(&codec->jackpoll_work);
 	if (!codec->in_freeing)
 		snd_hda_ctls_clear(codec);
@@ -784,7 +791,6 @@
 	snd_array_free(&codec->cvt_setups);
 	snd_array_free(&codec->spdif_out);
 	snd_array_free(&codec->verbs);
-	codec->preset = NULL;
 	codec->follower_dig_outs = NULL;
 	codec->spdif_status_reset = 0;
 	snd_array_free(&codec->mixers);
@@ -792,6 +798,7 @@
 	remove_conn_list(codec);
 	snd_hdac_regmap_exit(&codec->core);
 	codec->configured = 0;
+	refcount_set(&codec->pcm_ref, 1); /* reset refcount */
 }
 EXPORT_SYMBOL_GPL(snd_hda_codec_cleanup_for_unbind);
 
@@ -958,6 +965,8 @@
 	snd_array_init(&codec->verbs, sizeof(struct hda_verb *), 8);
 	INIT_LIST_HEAD(&codec->conn_list);
 	INIT_LIST_HEAD(&codec->pcm_list_head);
+	refcount_set(&codec->pcm_ref, 1);
+	init_waitqueue_head(&codec->remove_sleep);
 
 	INIT_DELAYED_WORK(&codec->jackpoll_work, hda_jackpoll_work);
 	codec->depop_delay = -1;
@@ -1727,8 +1736,11 @@
 {
 	int i;
 	struct hda_nid_item *items = codec->mixers.list;
+
+	down_write(&codec->card->controls_rwsem);
 	for (i = 0; i < codec->mixers.used; i++)
 		snd_ctl_remove(codec->card, items[i].kctl);
+	up_write(&codec->card->controls_rwsem);
 	snd_array_free(&codec->mixers);
 	snd_array_free(&codec->nids);
 }
@@ -2987,6 +2999,10 @@
 {
 	struct hda_pcm *cpcm;
 
+	/* Skip the shutdown if codec is not registered */
+	if (!codec->registered)
+		return;
+
 	list_for_each_entry(cpcm, &codec->pcm_list_head, list)
 		snd_pcm_suspend_all(cpcm->pcm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_component.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_component.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * HD audio Component Binding Interface
+ *
+ * Copyright (C) 2021 Cirrus Logic, Inc. and
+ *                    Cirrus Logic International Semiconductor Ltd.
+ */
+
+#include <linux/component.h>
+
+#define HDA_MAX_COMPONENTS	4
+#define HDA_MAX_NAME_SIZE	50
+
+struct hda_component {
+	struct device *dev;
+	char name[HDA_MAX_NAME_SIZE];
+	void (*playback_hook)(struct device *dev, int action);
+	int (*set_channel_map)(struct device *dev, unsigned int rx_num, unsigned int *rx_slot,
+				unsigned int tx_num, unsigned int *tx_slot);
+};
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_controller.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_controller.c
@@ -504,7 +504,6 @@
 		snd_pcm_gettime(substream->runtime, system_ts);
 
 		nsec = timecounter_read(&azx_dev->core.tc);
-		nsec = div_u64(nsec, 3); /* can be optimized */
 		if (audio_tstamp_config->report_delay)
 			nsec = azx_adjust_codec_delay(substream, nsec);
 
@@ -1034,10 +1033,8 @@
 void azx_stop_all_streams(struct azx *chip)
 {
 	struct hdac_bus *bus = azx_bus(chip);
-	struct hdac_stream *s;
 
-	list_for_each_entry(s, &bus->stream_list, list)
-		snd_hdac_stream_stop(s);
+	snd_hdac_stop_streams(bus);
 }
 EXPORT_SYMBOL_GPL(azx_stop_all_streams);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_generic.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_generic.c
@@ -91,6 +91,12 @@
 	free_kctls(spec);
 	snd_array_free(&spec->paths);
 	snd_array_free(&spec->loopback_list);
+#ifdef CONFIG_SND_HDA_GENERIC_LEDS
+	if (spec->led_cdevs[LED_AUDIO_MUTE])
+		led_classdev_unregister(spec->led_cdevs[LED_AUDIO_MUTE]);
+	if (spec->led_cdevs[LED_AUDIO_MICMUTE])
+		led_classdev_unregister(spec->led_cdevs[LED_AUDIO_MICMUTE]);
+#endif
 }
 
 /*
@@ -1149,8 +1155,8 @@
 	return path && path->ctls[ctl_type];
 }
 
-static const char * const channel_name[4] = {
-	"Front", "Surround", "CLFE", "Side"
+static const char * const channel_name[] = {
+	"Front", "Surround", "CLFE", "Side", "Back",
 };
 
 /* give some appropriate ctl name prefix for the given line out channel */
@@ -1176,7 +1182,7 @@
 
 	/* multi-io channels */
 	if (ch >= cfg->line_outs)
-		return channel_name[ch];
+		goto fixed_name;
 
 	switch (cfg->line_out_type) {
 	case AUTO_PIN_SPEAKER_OUT:
@@ -1228,6 +1234,7 @@
 	if (cfg->line_outs == 1 && !spec->multi_ios)
 		return "Line Out";
 
+ fixed_name:
 	if (ch >= ARRAY_SIZE(channel_name)) {
 		snd_BUG();
 		return "PCM";
@@ -1372,7 +1379,7 @@
 		struct nid_path *path;
 		hda_nid_t pin = pins[i];
 
-		if (!spec->obey_preferred_dacs) {
+		if (!spec->preferred_dacs) {
 			path = snd_hda_get_path_from_idx(codec, path_idx[i]);
 			if (path) {
 				badness += assign_out_path_ctls(codec, path);
@@ -1384,7 +1391,7 @@
 		if (dacs[i]) {
 			if (is_dac_already_used(codec, dacs[i]))
 				badness += bad->shared_primary;
-		} else if (spec->obey_preferred_dacs) {
+		} else if (spec->preferred_dacs) {
 			badness += BAD_NO_PRIMARY_DAC;
 		}
 
@@ -3922,7 +3929,10 @@
 						enum led_brightness),
 				bool micmute)
 {
+	struct hda_gen_spec *spec = codec->spec;
 	struct led_classdev *cdev;
+	int idx = micmute ? LED_AUDIO_MICMUTE : LED_AUDIO_MUTE;
+	int err;
 
 	cdev = devm_kzalloc(&codec->core.dev, sizeof(*cdev), GFP_KERNEL);
 	if (!cdev)
@@ -3932,10 +3942,14 @@
 	cdev->max_brightness = 1;
 	cdev->default_trigger = micmute ? "audio-micmute" : "audio-mute";
 	cdev->brightness_set_blocking = callback;
-	cdev->brightness = ledtrig_audio_get(micmute ? LED_AUDIO_MICMUTE : LED_AUDIO_MUTE);
+	cdev->brightness = ledtrig_audio_get(idx);
 	cdev->flags = LED_CORE_SUSPENDRESUME;
 
-	return devm_led_classdev_register(&codec->core.dev, cdev);
+	err = led_classdev_register(&codec->core.dev, cdev);
+	if (err < 0)
+		return err;
+	spec->led_cdevs[idx] = cdev;
+	return 0;
 }
 
 /**
@@ -4938,6 +4952,69 @@
 }
 EXPORT_SYMBOL_GPL(snd_hda_gen_stream_pm);
 
+/* forcibly mute the speaker output without caching; return true if updated */
+static bool force_mute_output_path(struct hda_codec *codec, hda_nid_t nid)
+{
+	if (!nid)
+		return false;
+	if (!nid_has_mute(codec, nid, HDA_OUTPUT))
+		return false; /* no mute, skip */
+	if (snd_hda_codec_amp_read(codec, nid, 0, HDA_OUTPUT, 0) &
+	    snd_hda_codec_amp_read(codec, nid, 1, HDA_OUTPUT, 0) &
+	    HDA_AMP_MUTE)
+		return false; /* both channels already muted, skip */
+
+	/* direct amp update without caching */
+	snd_hda_codec_write(codec, nid, 0, AC_VERB_SET_AMP_GAIN_MUTE,
+			    AC_AMP_SET_OUTPUT | AC_AMP_SET_LEFT |
+			    AC_AMP_SET_RIGHT | HDA_AMP_MUTE);
+	return true;
+}
+
+/**
+ * snd_hda_gen_shutup_speakers - Forcibly mute the speaker outputs
+ * @codec: the HDA codec
+ *
+ * Forcibly mute the speaker outputs, to be called at suspend or shutdown.
+ *
+ * The mute state done by this function isn't cached, hence the original state
+ * will be restored at resume.
+ *
+ * Return true if the mute state has been changed.
+ */
+bool snd_hda_gen_shutup_speakers(struct hda_codec *codec)
+{
+	struct hda_gen_spec *spec = codec->spec;
+	const int *paths;
+	const struct nid_path *path;
+	int i, p, num_paths;
+	bool updated = false;
+
+	/* if already powered off, do nothing */
+	if (!snd_hdac_is_power_on(&codec->core))
+		return false;
+
+	if (spec->autocfg.line_out_type == AUTO_PIN_SPEAKER_OUT) {
+		paths = spec->out_paths;
+		num_paths = spec->autocfg.line_outs;
+	} else {
+		paths = spec->speaker_paths;
+		num_paths = spec->autocfg.speaker_outs;
+	}
+
+	for (i = 0; i < num_paths; i++) {
+		path = snd_hda_get_path_from_idx(codec, paths[i]);
+		if (!path)
+			continue;
+		for (p = 0; p < path->depth; p++)
+			if (force_mute_output_path(codec, path->path[p]))
+				updated = true;
+	}
+
+	return updated;
+}
+EXPORT_SYMBOL_GPL(snd_hda_gen_shutup_speakers);
+
 /**
  * snd_hda_gen_parse_auto_config - Parse the given BIOS configuration and
  * set up the hda_gen_spec
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_generic.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_generic.h
@@ -294,6 +294,9 @@
 				   struct hda_jack_callback *cb);
 	void (*mic_autoswitch_hook)(struct hda_codec *codec,
 				    struct hda_jack_callback *cb);
+
+	/* leds */
+	struct led_classdev *led_cdevs[NUM_AUDIO_LEDS];
 };
 
 /* values for add_stereo_mix_input flag */
@@ -349,5 +352,6 @@
 int snd_hda_gen_add_micmute_led_cdev(struct hda_codec *codec,
 				     int (*callback)(struct led_classdev *,
 						     enum led_brightness));
+bool snd_hda_gen_shutup_speakers(struct hda_codec *codec);
 
 #endif /* __SOUND_HDA_GENERIC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_intel.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_intel.c
@@ -230,6 +230,7 @@
 	AZX_DRIVER_ATI,
 	AZX_DRIVER_ATIHDMI,
 	AZX_DRIVER_ATIHDMI_NS,
+	AZX_DRIVER_GFHDMI,
 	AZX_DRIVER_VIA,
 	AZX_DRIVER_SIS,
 	AZX_DRIVER_ULI,
@@ -331,11 +332,15 @@
 #define needs_eld_notify_link(chip)	false
 #endif
 
-#define CONTROLLER_IN_GPU(pci) (((pci)->device == 0x0a0c) || \
+#define CONTROLLER_IN_GPU(pci) (((pci)->vendor == 0x8086) &&         \
+				       (((pci)->device == 0x0a0c) || \
 					((pci)->device == 0x0c0c) || \
 					((pci)->device == 0x0d0c) || \
 					((pci)->device == 0x160c) || \
-					((pci)->device == 0x490d))
+					((pci)->device == 0x490d) || \
+					((pci)->device == 0x4f90) || \
+					((pci)->device == 0x4f91) || \
+					((pci)->device == 0x4f92)))
 
 #define IS_BXT(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0x5a98)
 
@@ -348,6 +353,7 @@
 	[AZX_DRIVER_ATI] = "HDA ATI SB",
 	[AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI",
 	[AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI",
+	[AZX_DRIVER_GFHDMI] = "HDA GF HDMI",
 	[AZX_DRIVER_VIA] = "HDA VIA VT82xx",
 	[AZX_DRIVER_SIS] = "HDA SIS966",
 	[AZX_DRIVER_ULI] = "HDA ULI M5461",
@@ -638,13 +644,17 @@
  * the update-IRQ timing.  The IRQ is issued before actually the
  * data is processed.  So, we need to process it afterwords in a
  * workqueue.
+ *
+ * Returns 1 if OK to proceed, 0 for delay handling, -1 for skipping update
  */
 static int azx_position_ok(struct azx *chip, struct azx_dev *azx_dev)
 {
 	struct snd_pcm_substream *substream = azx_dev->core.substream;
+	struct snd_pcm_runtime *runtime = substream->runtime;
 	int stream = substream->stream;
 	u32 wallclk;
 	unsigned int pos;
+	snd_pcm_uframes_t hwptr, target;
 
 	wallclk = azx_readl(chip, WALLCLK) - azx_dev->core.start_wallclk;
 	if (wallclk < (azx_dev->core.period_wallclk * 2) / 3)
@@ -681,6 +691,24 @@
 		/* NG - it's below the first next period boundary */
 		return chip->bdl_pos_adj ? 0 : -1;
 	azx_dev->core.start_wallclk += wallclk;
+
+	if (azx_dev->core.no_period_wakeup)
+		return 1; /* OK, no need to check period boundary */
+
+	if (runtime->hw_ptr_base != runtime->hw_ptr_interrupt)
+		return 1; /* OK, already in hwptr updating process */
+
+	/* check whether the period gets really elapsed */
+	pos = bytes_to_frames(runtime, pos);
+	hwptr = runtime->hw_ptr_base + pos;
+	if (hwptr < runtime->status->hw_ptr)
+		hwptr += runtime->buffer_size;
+	target = runtime->hw_ptr_interrupt + runtime->period_size;
+	if (hwptr < target) {
+		/* too early wakeup, process it later */
+		return chip->bdl_pos_adj ? 0 : -1;
+	}
+
 	return 1; /* OK, it's fine */
 }
 
@@ -859,31 +887,6 @@
 	return substream->runtime->delay;
 }
 
-static unsigned int azx_skl_get_dpib_pos(struct azx *chip,
-					 struct azx_dev *azx_dev)
-{
-	return _snd_hdac_chip_readl(azx_bus(chip),
-				    AZX_REG_VS_SDXDPIB_XBASE +
-				    (AZX_REG_VS_SDXDPIB_XINTERVAL *
-				     azx_dev->core.index));
-}
-
-/* get the current DMA position with correction on SKL+ chips */
-static unsigned int azx_get_pos_skl(struct azx *chip, struct azx_dev *azx_dev)
-{
-	/* DPIB register gives a more accurate position for playback */
-	if (azx_dev->core.substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-		return azx_skl_get_dpib_pos(chip, azx_dev);
-
-	/* For capture, we need to read posbuf, but it requires a delay
-	 * for the possible boundary overlap; the read of DPIB fetches the
-	 * actual posbuf
-	 */
-	udelay(20);
-	azx_skl_get_dpib_pos(chip, azx_dev);
-	return azx_get_pos_posbuf(chip, azx_dev);
-}
-
 static void __azx_shutdown_chip(struct azx *chip, bool skip_link_reset)
 {
 	azx_stop_chip(chip);
@@ -1573,7 +1576,7 @@
 		[POS_FIX_POSBUF] = azx_get_pos_posbuf,
 		[POS_FIX_VIACOMBO] = azx_via_get_position,
 		[POS_FIX_COMBO] = azx_get_pos_lpib,
-		[POS_FIX_SKL] = azx_get_pos_skl,
+		[POS_FIX_SKL] = azx_get_pos_posbuf,
 		[POS_FIX_FIFO] = azx_get_pos_fifo,
 	};
 
@@ -1611,6 +1614,7 @@
 	/* forced codec slots */
 	SND_PCI_QUIRK(0x1043, 0x1262, "ASUS W5Fm", 0x103),
 	SND_PCI_QUIRK(0x1046, 0x1262, "ASUS W5F", 0x103),
+	SND_PCI_QUIRK(0x1558, 0x0351, "Schenker Dock 15", 0x105),
 	/* WinFast VP200 H (Teradici) user reported broken communication */
 	SND_PCI_QUIRK(0x3a21, 0x040d, "WinFast VP200 H", 0x101),
 	{}
@@ -1740,6 +1744,12 @@
 	}
 
 	switch (chip->driver_type) {
+	/*
+	 * increase the bdl size for Glenfly Gpus for hardware
+	 * limitation on hdac interrupt interval
+	 */
+	case AZX_DRIVER_GFHDMI:
+		return 128;
 	case AZX_DRIVER_ICH:
 	case AZX_DRIVER_PCH:
 		return 1;
@@ -1794,8 +1804,6 @@
 
 	assign_position_fix(chip, check_position_fix(chip, position_fix[dev]));
 
-	check_probe_mask(chip, dev);
-
 	if (single_cmd < 0) /* allow fallback to single_cmd at errors */
 		chip->fallback_to_single_cmd = 1;
 	else /* explicitly set to single_cmd or not */
@@ -1821,6 +1829,8 @@
 		chip->bus.core.needs_damn_long_delay = 1;
 	}
 
+	check_probe_mask(chip, dev);
+
 	err = snd_device_new(card, SNDRV_DEV_LOWLEVEL, chip, &ops);
 	if (err < 0) {
 		dev_err(card->dev, "Error creating device [card]!\n");
@@ -1855,6 +1865,12 @@
 		pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0);
 	}
 #endif
+	/*
+	 * Fix response write request not synced to memory when handle
+	 * hdac interrupt on Glenfly Gpus
+	 */
+	if (chip->driver_type == AZX_DRIVER_GFHDMI)
+		bus->polling_mode = 1;
 
 	err = pcim_iomap_regions(pci, 1 << 0, "ICH HD audio");
 	if (err < 0)
@@ -1955,6 +1971,7 @@
 			chip->playback_streams = ATIHDMI_NUM_PLAYBACK;
 			chip->capture_streams = ATIHDMI_NUM_CAPTURE;
 			break;
+		case AZX_DRIVER_GFHDMI:
 		case AZX_DRIVER_GENERIC:
 		default:
 			chip->playback_streams = ICH6_NUM_PLAYBACK;
@@ -2186,12 +2203,17 @@
 	SND_PCI_QUIRK(0x8086, 0x2068, "Intel NUC7i3BNB", 0),
 	/* https://bugzilla.kernel.org/show_bug.cgi?id=198611 */
 	SND_PCI_QUIRK(0x17aa, 0x2227, "Lenovo X1 Carbon 3rd Gen", 0),
+	SND_PCI_QUIRK(0x17aa, 0x316e, "Lenovo ThinkCentre M70q", 0),
 	/* https://bugzilla.redhat.com/show_bug.cgi?id=1689623 */
 	SND_PCI_QUIRK(0x17aa, 0x367b, "Lenovo IdeaCentre B550", 0),
 	/* https://bugzilla.redhat.com/show_bug.cgi?id=1572975 */
 	SND_PCI_QUIRK(0x17aa, 0x36a7, "Lenovo C50 All in one", 0),
 	/* https://bugs.launchpad.net/bugs/1821663 */
 	SND_PCI_QUIRK(0x1631, 0xe017, "Packard Bell NEC IMEDIA 5204", 0),
+	/* KONTRON SinglePC may cause a stall at runtime resume */
+	SND_PCI_QUIRK(0x1734, 0x1232, "KONTRON SinglePC", 0),
+	/* Dell ALC3271 */
+	SND_PCI_QUIRK(0x1028, 0x0962, "Dell ALC3271", 0),
 	{}
 };
 #endif /* CONFIG_PM */
@@ -2330,7 +2352,8 @@
 
 out_free:
 	if (err < 0) {
-		azx_free(chip);
+		pci_set_drvdata(pci, NULL);
+		snd_card_free(chip->card);
 		return err;
 	}
 
@@ -2474,6 +2497,13 @@
 	/* DG1 */
 	{ PCI_DEVICE(0x8086, 0x490d),
 	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	/* DG2 */
+	{ PCI_DEVICE(0x8086, 0x4f90),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	{ PCI_DEVICE(0x8086, 0x4f91),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	{ PCI_DEVICE(0x8086, 0x4f92),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
 	/* Alderlake-S */
 	{ PCI_DEVICE(0x8086, 0x7ad0),
 	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
@@ -2488,6 +2518,19 @@
 	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
 	{ PCI_DEVICE(0x8086, 0x4b58),
 	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	/* Raptor Lake */
+	{ PCI_DEVICE(0x8086, 0x7a50),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	{ PCI_DEVICE(0x8086, 0x51ca),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	{ PCI_DEVICE(0x8086, 0x51cb),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	{ PCI_DEVICE(0x8086, 0x51ce),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	{ PCI_DEVICE(0x8086, 0x51cf),
+	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE},
+	/* Arrow Lake */
+	{ PCI_DEVICE_DATA(INTEL, HDA_ARL, AZX_DRIVER_SKL | AZX_DCAPS_INTEL_SKYLAKE) },
 	/* Broxton-P(Apollolake) */
 	{ PCI_DEVICE(0x8086, 0x5a98),
 	  .driver_data = AZX_DRIVER_SKL | AZX_DCAPS_INTEL_BROXTON },
@@ -2510,9 +2553,12 @@
 	/* 5 Series/3400 */
 	{ PCI_DEVICE(0x8086, 0x3b56),
 	  .driver_data = AZX_DRIVER_SCH | AZX_DCAPS_INTEL_PCH_NOPM },
+	{ PCI_DEVICE(0x8086, 0x3b57),
+	  .driver_data = AZX_DRIVER_SCH | AZX_DCAPS_INTEL_PCH_NOPM },
 	/* Poulsbo */
 	{ PCI_DEVICE(0x8086, 0x811b),
-	  .driver_data = AZX_DRIVER_SCH | AZX_DCAPS_INTEL_PCH_BASE },
+	  .driver_data = AZX_DRIVER_SCH | AZX_DCAPS_INTEL_PCH_BASE |
+	  AZX_DCAPS_POSFIX_LPIB },
 	/* Oaktrail */
 	{ PCI_DEVICE(0x8086, 0x080a),
 	  .driver_data = AZX_DRIVER_SCH | AZX_DCAPS_INTEL_PCH_BASE },
@@ -2675,9 +2721,18 @@
 	{ PCI_DEVICE(0x1002, 0xab28),
 	  .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS |
 	  AZX_DCAPS_PM_RUNTIME },
+	{ PCI_DEVICE(0x1002, 0xab30),
+	  .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS |
+	  AZX_DCAPS_PM_RUNTIME },
 	{ PCI_DEVICE(0x1002, 0xab38),
 	  .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS |
 	  AZX_DCAPS_PM_RUNTIME },
+	/* GLENFLY */
+	{ PCI_DEVICE(PCI_VENDOR_ID_GLENFLY, PCI_ANY_ID),
+	  .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8,
+	  .class_mask = 0xffffff,
+	  .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB |
+	  AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT },
 	/* VIA VT8251/VT8237A */
 	{ PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA },
 	/* VIA GFX VT7122/VX900 */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_jack.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_jack.c
@@ -158,6 +158,17 @@
 	return jack;
 }
 
+void snd_hda_jack_tbl_disconnect(struct hda_codec *codec)
+{
+	struct hda_jack_tbl *jack = codec->jacktbl.list;
+	int i;
+
+	for (i = 0; i < codec->jacktbl.used; i++, jack++) {
+		if (!codec->bus->shutdown && jack->jack)
+			snd_device_disconnect(codec->card, jack->jack);
+	}
+}
+
 void snd_hda_jack_tbl_clear(struct hda_codec *codec)
 {
 	struct hda_jack_tbl *jack = codec->jacktbl.list;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_jack.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_jack.h
@@ -69,6 +69,7 @@
 snd_hda_jack_tbl_get_from_tag(struct hda_codec *codec,
 			      unsigned char tag, int dev_id);
 
+void snd_hda_jack_tbl_disconnect(struct hda_codec *codec);
 void snd_hda_jack_tbl_clear(struct hda_codec *codec);
 
 void snd_hda_jack_set_dirty_all(struct hda_codec *codec);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_local.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_local.h
@@ -137,6 +137,7 @@
 int snd_hda_codec_reset(struct hda_codec *codec);
 void snd_hda_codec_register(struct hda_codec *codec);
 void snd_hda_codec_cleanup_for_unbind(struct hda_codec *codec);
+void snd_hda_codec_disconnect_pcms(struct hda_codec *codec);
 
 #define snd_hda_regmap_sync(codec)	snd_hdac_regmap_sync(&(codec)->core)
 
@@ -349,6 +350,7 @@
 void snd_hda_apply_pincfgs(struct hda_codec *codec,
 			   const struct hda_pintbl *cfg);
 void snd_hda_apply_fixup(struct hda_codec *codec, int action);
+void __snd_hda_apply_fixup(struct hda_codec *codec, int id, int action, int depth);
 void snd_hda_pick_fixup(struct hda_codec *codec,
 			const struct hda_model_fixup *models,
 			const struct snd_pci_quirk *quirk,
@@ -438,6 +440,15 @@
 #define for_each_hda_codec_node(nid, codec) \
 	for ((nid) = (codec)->core.start_nid; (nid) < (codec)->core.end_nid; (nid)++)
 
+/* Set the codec power_state flag to indicate to allow unsol event handling;
+ * see hda_codec_unsol_event() in hda_bind.c.  Calling this might confuse the
+ * state tracking, so use with care.
+ */
+static inline void snd_hda_codec_allow_unsol_events(struct hda_codec *codec)
+{
+	codec->core.dev.power.power_state = PMSG_ON;
+}
+
 /*
  * get widget capabilities
  */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/hda_tegra.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/hda_tegra.c
@@ -68,14 +68,20 @@
  */
 #define TEGRA194_NUM_SDO_LINES	  4
 
+struct hda_tegra_soc {
+	bool has_hda2codec_2x_reset;
+};
+
 struct hda_tegra {
 	struct azx chip;
 	struct device *dev;
-	struct reset_control *reset;
+	struct reset_control_bulk_data resets[3];
 	struct clk_bulk_data clocks[3];
+	unsigned int nresets;
 	unsigned int nclocks;
 	void __iomem *regs;
 	struct work_struct probe_work;
+	const struct hda_tegra_soc *soc;
 };
 
 #ifdef CONFIG_PM
@@ -170,7 +176,7 @@
 	int rc;
 
 	if (!chip->running) {
-		rc = reset_control_assert(hda->reset);
+		rc = reset_control_bulk_assert(hda->nresets, hda->resets);
 		if (rc)
 			return rc;
 	}
@@ -187,7 +193,7 @@
 	} else {
 		usleep_range(10, 100);
 
-		rc = reset_control_deassert(hda->reset);
+		rc = reset_control_bulk_deassert(hda->nresets, hda->resets);
 		if (rc)
 			return rc;
 	}
@@ -427,9 +433,17 @@
 	return 0;
 }
 
+static const struct hda_tegra_soc tegra30_data = {
+	.has_hda2codec_2x_reset = true,
+};
+
+static const struct hda_tegra_soc tegra194_data = {
+	.has_hda2codec_2x_reset = false,
+};
+
 static const struct of_device_id hda_tegra_match[] = {
-	{ .compatible = "nvidia,tegra30-hda" },
-	{ .compatible = "nvidia,tegra194-hda" },
+	{ .compatible = "nvidia,tegra30-hda", .data = &tegra30_data },
+	{ .compatible = "nvidia,tegra194-hda", .data = &tegra194_data },
 	{},
 };
 MODULE_DEVICE_TABLE(of, hda_tegra_match);
@@ -437,7 +451,8 @@
 static int hda_tegra_probe(struct platform_device *pdev)
 {
 	const unsigned int driver_flags = AZX_DCAPS_CORBRP_SELF_CLEAR |
-					  AZX_DCAPS_PM_RUNTIME;
+					  AZX_DCAPS_PM_RUNTIME |
+					  AZX_DCAPS_4K_BDLE_BOUNDARY;
 	struct snd_card *card;
 	struct azx *chip;
 	struct hda_tegra *hda;
@@ -449,6 +464,8 @@
 	hda->dev = &pdev->dev;
 	chip = &hda->chip;
 
+	hda->soc = of_device_get_match_data(&pdev->dev);
+
 	err = snd_card_new(&pdev->dev, SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1,
 			   THIS_MODULE, 0, &card);
 	if (err < 0) {
@@ -456,11 +473,20 @@
 		return err;
 	}
 
-	hda->reset = devm_reset_control_array_get_exclusive(&pdev->dev);
-	if (IS_ERR(hda->reset)) {
-		err = PTR_ERR(hda->reset);
+	hda->resets[hda->nresets++].id = "hda";
+	hda->resets[hda->nresets++].id = "hda2hdmi";
+	/*
+	 * "hda2codec_2x" reset is not present on Tegra194. Though DT would
+	 * be updated to reflect this, but to have backward compatibility
+	 * below is necessary.
+	 */
+	if (hda->soc->has_hda2codec_2x_reset)
+		hda->resets[hda->nresets++].id = "hda2codec_2x";
+
+	err = devm_reset_control_bulk_get_exclusive(&pdev->dev, hda->nresets,
+						    hda->resets);
+	if (err)
 		goto out_free;
-	}
 
 	hda->clocks[hda->nclocks++].id = "hda";
 	hda->clocks[hda->nclocks++].id = "hda2hdmi";
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_ca0132.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_ca0132.c
@@ -1306,6 +1306,8 @@
 	SND_PCI_QUIRK(0x1458, 0xA026, "Gigabyte G1.Sniper Z97", QUIRK_R3DI),
 	SND_PCI_QUIRK(0x1458, 0xA036, "Gigabyte GA-Z170X-Gaming 7", QUIRK_R3DI),
 	SND_PCI_QUIRK(0x3842, 0x1038, "EVGA X99 Classified", QUIRK_R3DI),
+	SND_PCI_QUIRK(0x3842, 0x104b, "EVGA X299 Dark", QUIRK_R3DI),
+	SND_PCI_QUIRK(0x3842, 0x1055, "EVGA Z390 DARK", QUIRK_R3DI),
 	SND_PCI_QUIRK(0x1102, 0x0013, "Recon3D", QUIRK_R3D),
 	SND_PCI_QUIRK(0x1102, 0x0018, "Recon3D", QUIRK_R3D),
 	SND_PCI_QUIRK(0x1102, 0x0051, "Sound Blaster AE-5", QUIRK_AE5),
@@ -2454,7 +2456,7 @@
 static int dspio_alloc_dma_chan(struct hda_codec *codec, unsigned int *dma_chan)
 {
 	int status = 0;
-	unsigned int size = sizeof(dma_chan);
+	unsigned int size = sizeof(*dma_chan);
 
 	codec_dbg(codec, "     dspio_alloc_dma_chan() -- begin\n");
 	status = dspio_scp(codec, MASTERCONTROL, 0x20,
@@ -4230,8 +4232,10 @@
 
 	for (i = 0; i < TUNING_CTLS_COUNT; i++)
 		if (nid == ca0132_tuning_ctls[i].nid)
-			break;
+			goto found;
 
+	return -EINVAL;
+found:
 	snd_hda_power_up(codec);
 	dspio_set_param(codec, ca0132_tuning_ctls[i].mid, 0x20,
 			ca0132_tuning_ctls[i].req,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_cirrus.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_cirrus.c
@@ -395,6 +395,7 @@
 
 	/* codec SSID */
 	SND_PCI_QUIRK(0x106b, 0x0600, "iMac 14,1", CS420X_IMAC27_122),
+	SND_PCI_QUIRK(0x106b, 0x0900, "iMac 12,1", CS420X_IMAC27_122),
 	SND_PCI_QUIRK(0x106b, 0x1c00, "MacBookPro 8,1", CS420X_MBP81),
 	SND_PCI_QUIRK(0x106b, 0x2000, "iMac 12,2", CS420X_IMAC27_122),
 	SND_PCI_QUIRK(0x106b, 0x2800, "MacBookPro 10,1", CS420X_MBP101),
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_conexant.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_conexant.c
@@ -42,7 +42,7 @@
 	unsigned int gpio_led;
 	unsigned int gpio_mute_led_mask;
 	unsigned int gpio_mic_led_mask;
-
+	bool is_cx8070_sn6140;
 };
 
 
@@ -164,6 +164,27 @@
 	}
 }
 
+static void cx_fixup_headset_recog(struct hda_codec *codec)
+{
+	unsigned int mic_persent;
+
+	/* fix some headset type recognize fail issue, such as EDIFIER headset */
+	/* set micbiasd output current comparator threshold from 66% to 55%. */
+	snd_hda_codec_write(codec, 0x1c, 0, 0x320, 0x010);
+	/* set OFF voltage for DFET from -1.2V to -0.8V, set headset micbias registor
+	 * value adjustment trim from 2.2K ohms to 2.0K ohms.
+	 */
+	snd_hda_codec_write(codec, 0x1c, 0, 0x3b0, 0xe10);
+	/* fix reboot headset type recognize fail issue */
+	mic_persent = snd_hda_codec_read(codec, 0x19, 0, AC_VERB_GET_PIN_SENSE, 0x0);
+	if (mic_persent & AC_PINSENSE_PRESENCE)
+		/* enable headset mic VREF */
+		snd_hda_codec_write(codec, 0x19, 0, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24);
+	else
+		/* disable headset mic VREF */
+		snd_hda_codec_write(codec, 0x19, 0, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x20);
+}
+
 static int cx_auto_init(struct hda_codec *codec)
 {
 	struct conexant_spec *spec = codec->spec;
@@ -174,6 +195,9 @@
 	cxt_init_gpio_led(codec);
 	snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_INIT);
 
+	if (spec->is_cx8070_sn6140)
+		cx_fixup_headset_recog(codec);
+
 	return 0;
 }
 
@@ -192,6 +216,48 @@
 	snd_hda_gen_free(codec);
 }
 
+static void cx_process_headset_plugin(struct hda_codec *codec)
+{
+	unsigned int val;
+	unsigned int count = 0;
+
+	/* Wait headset detect done. */
+	do {
+		val = snd_hda_codec_read(codec, 0x1c, 0, 0xca0, 0x0);
+		if (val & 0x080) {
+			codec_dbg(codec, "headset type detect done!\n");
+			break;
+		}
+		msleep(20);
+		count++;
+	} while (count < 3);
+	val = snd_hda_codec_read(codec, 0x1c, 0, 0xcb0, 0x0);
+	if (val & 0x800) {
+		codec_dbg(codec, "headset plugin, type is CTIA\n");
+		snd_hda_codec_write(codec, 0x19, 0, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24);
+	} else if (val & 0x400) {
+		codec_dbg(codec, "headset plugin, type is OMTP\n");
+		snd_hda_codec_write(codec, 0x19, 0, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24);
+	} else {
+		codec_dbg(codec, "headphone plugin\n");
+	}
+}
+
+static void cx_update_headset_mic_vref(struct hda_codec *codec, struct hda_jack_callback *event)
+{
+	unsigned int mic_present;
+
+	/* In cx8070 and sn6140, the node 16 can only be config to headphone or disabled,
+	 * the node 19 can only be config to microphone or disabled.
+	 * Check hp&mic tag to process headset pulgin&plugout.
+	 */
+	mic_present = snd_hda_codec_read(codec, 0x19, 0, AC_VERB_GET_PIN_SENSE, 0x0);
+	if (!(mic_present & AC_PINSENSE_PRESENCE)) /* mic plugout */
+		snd_hda_codec_write(codec, 0x19, 0, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x20);
+	else
+		cx_process_headset_plugin(codec);
+}
+
 #ifdef CONFIG_PM
 static int cx_auto_suspend(struct hda_codec *codec)
 {
@@ -222,6 +288,7 @@
 	CXT_PINCFG_LEMOTE_A1205,
 	CXT_PINCFG_COMPAQ_CQ60,
 	CXT_FIXUP_STEREO_DMIC,
+	CXT_PINCFG_LENOVO_NOTEBOOK,
 	CXT_FIXUP_INC_MIC_BOOST,
 	CXT_FIXUP_HEADPHONE_MIC_PIN,
 	CXT_FIXUP_HEADPHONE_MIC,
@@ -238,9 +305,13 @@
 	CXT_FIXUP_HP_SPECTRE,
 	CXT_FIXUP_HP_GATE_MIC,
 	CXT_FIXUP_MUTE_LED_GPIO,
+	CXT_FIXUP_HP_ELITEONE_OUT_DIS,
 	CXT_FIXUP_HP_ZBOOK_MUTE_LED,
 	CXT_FIXUP_HEADSET_MIC,
 	CXT_FIXUP_HP_MIC_NO_PRESENCE,
+	CXT_PINCFG_SWS_JS201D,
+	CXT_PINCFG_TOP_SPEAKER,
+	CXT_FIXUP_HP_A_U,
 };
 
 /* for hda_fixup_thinkpad_acpi() */
@@ -253,6 +324,19 @@
 	spec->gen.inv_dmic_split = 1;
 }
 
+/* fix widget control pin settings */
+static void cxt_fixup_update_pinctl(struct hda_codec *codec,
+				   const struct hda_fixup *fix, int action)
+{
+	if (action == HDA_FIXUP_ACT_PROBE) {
+		/* Unset OUT_EN for this Node pin, leaving only HP_EN.
+		 * This is the value stored in the codec register after
+		 * the correct initialization of the previous windows boot.
+		 */
+		snd_hda_set_pin_ctl_cache(codec, 0x1d, AC_PINCTL_HP_EN);
+	}
+}
+
 static void cxt5066_increase_mic_boost(struct hda_codec *codec,
 				   const struct hda_fixup *fix, int action)
 {
@@ -695,6 +779,18 @@
 	}
 }
 
+static void cxt_setup_gpio_unmute(struct hda_codec *codec,
+				  unsigned int gpio_mute_mask)
+{
+	if (gpio_mute_mask) {
+		// set gpio data to 0.
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_DATA, 0);
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_MASK, gpio_mute_mask);
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_DIRECTION, gpio_mute_mask);
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_STICKY_MASK, 0);
+	}
+}
+
 static void cxt_fixup_mute_led_gpio(struct hda_codec *codec,
 				const struct hda_fixup *fix, int action)
 {
@@ -709,6 +805,15 @@
 		cxt_setup_mute_led(codec, 0x10, 0x20);
 }
 
+static void cxt_fixup_hp_a_u(struct hda_codec *codec,
+			     const struct hda_fixup *fix, int action)
+{
+	// Init vers in BIOS mute the spk/hp by set gpio high to avoid pop noise,
+	// so need to unmute once by clearing the gpio data when runs into the system.
+	if (action == HDA_FIXUP_ACT_INIT)
+		cxt_setup_gpio_unmute(codec, 0x2);
+}
+
 /* ThinkPad X200 & co with cxt5051 */
 static const struct hda_pintbl cxt_pincfg_lenovo_x200[] = {
 	{ 0x16, 0x042140ff }, /* HP (seq# overridden) */
@@ -738,6 +843,34 @@
 	{}
 };
 
+/* SuoWoSi/South-holding JS201D with sn6140 */
+static const struct hda_pintbl cxt_pincfg_sws_js201d[] = {
+	{ 0x16, 0x03211040 }, /* hp out */
+	{ 0x17, 0x91170110 }, /* SPK/Class_D */
+	{ 0x18, 0x95a70130 }, /* Internal mic */
+	{ 0x19, 0x03a11020 }, /* Headset Mic */
+	{ 0x1a, 0x40f001f0 }, /* Not used */
+	{ 0x21, 0x40f001f0 }, /* Not used */
+	{}
+};
+
+/* pincfg quirk for Tuxedo Sirius;
+ * unfortunately the (PCI) SSID conflicts with System76 Pangolin pang14,
+ * which has incompatible pin setup, so we check the codec SSID (luckily
+ * different one!) and conditionally apply the quirk here
+ */
+static void cxt_fixup_sirius_top_speaker(struct hda_codec *codec,
+					 const struct hda_fixup *fix,
+					 int action)
+{
+	/* ignore for incorrectly picked-up pang14 */
+	if (codec->core.subsystem_id == 0x278212b3)
+		return;
+	/* set up the top speaker pin */
+	if (action == HDA_FIXUP_ACT_PRE_PROBE)
+		snd_hda_codec_set_pincfg(codec, 0x1d, 0x82170111);
+}
+
 static const struct hda_fixup cxt_fixups[] = {
 	[CXT_PINCFG_LENOVO_X200] = {
 		.type = HDA_FIXUP_PINS,
@@ -772,6 +905,14 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = cxt_fixup_stereo_dmic,
 	},
+	[CXT_PINCFG_LENOVO_NOTEBOOK] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x1a, 0x05d71030 },
+			{ }
+		},
+		.chain_id = CXT_FIXUP_STEREO_DMIC,
+	},
 	[CXT_FIXUP_INC_MIC_BOOST] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = cxt5066_increase_mic_boost,
@@ -868,6 +1009,10 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = cxt_fixup_mute_led_gpio,
 	},
+	[CXT_FIXUP_HP_ELITEONE_OUT_DIS] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cxt_fixup_update_pinctl,
+	},
 	[CXT_FIXUP_HP_ZBOOK_MUTE_LED] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = cxt_fixup_hp_zbook_mute_led,
@@ -885,6 +1030,18 @@
 		.chained = true,
 		.chain_id = CXT_FIXUP_HEADSET_MIC,
 	},
+	[CXT_PINCFG_SWS_JS201D] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = cxt_pincfg_sws_js201d,
+	},
+	[CXT_PINCFG_TOP_SPEAKER] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cxt_fixup_sirius_top_speaker,
+	},
+	[CXT_FIXUP_HP_A_U] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cxt_fixup_hp_a_u,
+	},
 };
 
 static const struct snd_pci_quirk cxt5045_fixups[] = {
@@ -941,14 +1098,17 @@
 	SND_PCI_QUIRK(0x103c, 0x814f, "HP ZBook 15u G3", CXT_FIXUP_MUTE_LED_GPIO),
 	SND_PCI_QUIRK(0x103c, 0x8174, "HP Spectre x360", CXT_FIXUP_HP_SPECTRE),
 	SND_PCI_QUIRK(0x103c, 0x822e, "HP ProBook 440 G4", CXT_FIXUP_MUTE_LED_GPIO),
+	SND_PCI_QUIRK(0x103c, 0x8231, "HP ProBook 450 G4", CXT_FIXUP_MUTE_LED_GPIO),
 	SND_PCI_QUIRK(0x103c, 0x828c, "HP EliteBook 840 G4", CXT_FIXUP_HP_DOCK),
 	SND_PCI_QUIRK(0x103c, 0x8299, "HP 800 G3 SFF", CXT_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x829a, "HP 800 G3 DM", CXT_FIXUP_HP_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x103c, 0x82b4, "HP ProDesk 600 G3", CXT_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x836e, "HP ProBook 455 G5", CXT_FIXUP_MUTE_LED_GPIO),
 	SND_PCI_QUIRK(0x103c, 0x837f, "HP ProBook 470 G5", CXT_FIXUP_MUTE_LED_GPIO),
 	SND_PCI_QUIRK(0x103c, 0x83b2, "HP EliteBook 840 G5", CXT_FIXUP_HP_DOCK),
 	SND_PCI_QUIRK(0x103c, 0x83b3, "HP EliteBook 830 G5", CXT_FIXUP_HP_DOCK),
 	SND_PCI_QUIRK(0x103c, 0x83d3, "HP ProBook 640 G4", CXT_FIXUP_HP_DOCK),
+	SND_PCI_QUIRK(0x103c, 0x83e5, "HP EliteOne 1000 G2", CXT_FIXUP_HP_ELITEONE_OUT_DIS),
 	SND_PCI_QUIRK(0x103c, 0x8402, "HP ProBook 645 G4", CXT_FIXUP_MUTE_LED_GPIO),
 	SND_PCI_QUIRK(0x103c, 0x8427, "HP ZBook Studio G5", CXT_FIXUP_HP_ZBOOK_MUTE_LED),
 	SND_PCI_QUIRK(0x103c, 0x844f, "HP ZBook Studio G5", CXT_FIXUP_HP_ZBOOK_MUTE_LED),
@@ -957,6 +1117,8 @@
 	SND_PCI_QUIRK(0x103c, 0x8457, "HP Z2 G4 mini", CXT_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x8458, "HP Z2 G4 mini premium", CXT_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1043, 0x138d, "Asus", CXT_FIXUP_HEADPHONE_MIC_PIN),
+	SND_PCI_QUIRK(0x14f1, 0x0252, "MBX-Z60MR100", CXT_FIXUP_HP_A_U),
+	SND_PCI_QUIRK(0x14f1, 0x0265, "SWS JS201D", CXT_PINCFG_SWS_JS201D),
 	SND_PCI_QUIRK(0x152d, 0x0833, "OLPC XO-1.5", CXT_FIXUP_OLPC_XO),
 	SND_PCI_QUIRK(0x17aa, 0x20f2, "Lenovo T400", CXT_PINCFG_LENOVO_TP410),
 	SND_PCI_QUIRK(0x17aa, 0x215e, "Lenovo T410", CXT_PINCFG_LENOVO_TP410),
@@ -970,12 +1132,17 @@
 	SND_PCI_QUIRK(0x17aa, 0x3905, "Lenovo G50-30", CXT_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK(0x17aa, 0x390b, "Lenovo G50-80", CXT_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK(0x17aa, 0x3975, "Lenovo U300s", CXT_FIXUP_STEREO_DMIC),
+	/* NOTE: we'd need to extend the quirk for 17aa:3977 as the same
+	 * PCI SSID is used on multiple Lenovo models
+	 */
 	SND_PCI_QUIRK(0x17aa, 0x3977, "Lenovo IdeaPad U310", CXT_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK(0x17aa, 0x3978, "Lenovo G50-70", CXT_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK(0x17aa, 0x397b, "Lenovo S205", CXT_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK_VENDOR(0x17aa, "Thinkpad", CXT_FIXUP_THINKPAD_ACPI),
 	SND_PCI_QUIRK(0x1c06, 0x2011, "Lemote A1004", CXT_PINCFG_LEMOTE_A1004),
 	SND_PCI_QUIRK(0x1c06, 0x2012, "Lemote A1205", CXT_PINCFG_LEMOTE_A1205),
+	SND_PCI_QUIRK(0x2782, 0x12c3, "Sirius Gen1", CXT_PINCFG_TOP_SPEAKER),
+	SND_PCI_QUIRK(0x2782, 0x12c5, "Sirius Gen2", CXT_PINCFG_TOP_SPEAKER),
 	{}
 };
 
@@ -993,6 +1160,10 @@
 	{ .id = CXT_FIXUP_MUTE_LED_GPIO, .name = "mute-led-gpio" },
 	{ .id = CXT_FIXUP_HP_ZBOOK_MUTE_LED, .name = "hp-zbook-mute-led" },
 	{ .id = CXT_FIXUP_HP_MIC_NO_PRESENCE, .name = "hp-mic-fix" },
+	{ .id = CXT_PINCFG_LENOVO_NOTEBOOK, .name = "lenovo-20149" },
+	{ .id = CXT_PINCFG_SWS_JS201D, .name = "sws-js201d" },
+	{ .id = CXT_PINCFG_TOP_SPEAKER, .name = "sirius-top-speaker" },
+	{ .id = CXT_FIXUP_HP_A_U, .name = "HP-U-support" },
 	{}
 };
 
@@ -1028,6 +1199,15 @@
 	codec->spec = spec;
 	codec->patch_ops = cx_auto_patch_ops;
 
+	/* init cx8070/sn6140 flag and reset headset_present_flag */
+	switch (codec->core.vendor_id) {
+	case 0x14f11f86:
+	case 0x14f11f87:
+		spec->is_cx8070_sn6140 = true;
+		snd_hda_jack_detect_enable_callback(codec, 0x19, cx_update_headset_mic_vref);
+		break;
+	}
+
 	cx_auto_parse_eapd(codec);
 	spec->gen.own_eapd_ctl = 1;
 
@@ -1052,6 +1232,13 @@
 		snd_hda_pick_fixup(codec, cxt5051_fixup_models,
 				   cxt5051_fixups, cxt_fixups);
 		break;
+	case 0x14f15098:
+		codec->pin_amp_workaround = 1;
+		spec->gen.mixer_nid = 0x22;
+		spec->gen.add_stereo_mix_input = HDA_HINT_STEREO_MIX_AUTO;
+		snd_hda_pick_fixup(codec, cxt5066_fixup_models,
+				   cxt5066_fixups, cxt_fixups);
+		break;
 	case 0x14f150f2:
 		codec->power_save_node = 1;
 		fallthrough;
@@ -1072,11 +1259,11 @@
 	if (err < 0)
 		goto error;
 
-	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
+	err = cx_auto_parse_beep(codec);
 	if (err < 0)
 		goto error;
 
-	err = cx_auto_parse_beep(codec);
+	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
 	if (err < 0)
 		goto error;
 
@@ -1107,6 +1294,7 @@
 	HDA_CODEC_ENTRY(0x14f11f86, "CX8070", patch_conexant_auto),
 	HDA_CODEC_ENTRY(0x14f12008, "CX8200", patch_conexant_auto),
 	HDA_CODEC_ENTRY(0x14f120d0, "CX11970", patch_conexant_auto),
+	HDA_CODEC_ENTRY(0x14f120d1, "SN6180", patch_conexant_auto),
 	HDA_CODEC_ENTRY(0x14f15045, "CX20549 (Venice)", patch_conexant_auto),
 	HDA_CODEC_ENTRY(0x14f15047, "CX20551 (Waikiki)", patch_conexant_auto),
 	HDA_CODEC_ENTRY(0x14f15051, "CX20561 (Hermosa)", patch_conexant_auto),
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_cs8409-tables.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_cs8409-tables.c
@@ -76,67 +76,74 @@
 	{} /* terminator */
 };
 
+const struct hda_pintbl cs8409_cs42l42_pincfgs_no_dmic[] = {
+	{ CS8409_PIN_ASP1_TRANSMITTER_A, 0x042120f0 },	/* ASP-1-TX */
+	{ CS8409_PIN_ASP1_RECEIVER_A, 0x04a12050 },	/* ASP-1-RX */
+	{ CS8409_PIN_ASP2_TRANSMITTER_A, 0x901000f0 },	/* ASP-2-TX */
+	{} /* terminator */
+};
+
 /* Vendor specific HW configuration for CS42L42 */
 static const struct cs8409_i2c_param cs42l42_init_reg_seq[] = {
-	{ 0x1010, 0xB0 },
-	{ 0x1D01, 0x00 },
+	{ CS42L42_I2C_TIMEOUT, 0xB0 },
+	{ CS42L42_ADC_CTL, 0x00 },
 	{ 0x1D02, 0x06 },
-	{ 0x1D03, 0x9F },
-	{ 0x1107, 0x01 },
-	{ 0x1009, 0x02 },
-	{ 0x1007, 0x03 },
-	{ 0x1201, 0x00 },
-	{ 0x1208, 0x13 },
-	{ 0x1205, 0xFF },
-	{ 0x1206, 0x00 },
-	{ 0x1207, 0x20 },
-	{ 0x1202, 0x0D },
-	{ 0x2A02, 0x02 },
-	{ 0x2A03, 0x00 },
-	{ 0x2A04, 0x00 },
-	{ 0x2A05, 0x02 },
-	{ 0x2A06, 0x00 },
-	{ 0x2A07, 0x20 },
-	{ 0x2A08, 0x02 },
-	{ 0x2A09, 0x00 },
-	{ 0x2A0A, 0x80 },
-	{ 0x2A0B, 0x02 },
-	{ 0x2A0C, 0x00 },
-	{ 0x2A0D, 0xA0 },
-	{ 0x2A01, 0x0C },
-	{ 0x2902, 0x01 },
-	{ 0x2903, 0x02 },
-	{ 0x2904, 0x00 },
-	{ 0x2905, 0x00 },
-	{ 0x2901, 0x01 },
-	{ 0x1101, 0x0A },
-	{ 0x1102, 0x84 },
-	{ 0x2301, 0x3F },
-	{ 0x2303, 0x3F },
-	{ 0x2302, 0x3f },
-	{ 0x2001, 0x03 },
-	{ 0x1B75, 0xB6 },
-	{ 0x1B73, 0xC2 },
-	{ 0x1129, 0x01 },
-	{ 0x1121, 0xF3 },
-	{ 0x1103, 0x20 },
-	{ 0x1105, 0x00 },
-	{ 0x1112, 0x00 },
-	{ 0x1113, 0x80 },
-	{ 0x1C03, 0xC0 },
-	{ 0x1101, 0x02 },
-	{ 0x1316, 0xff },
-	{ 0x1317, 0xff },
-	{ 0x1318, 0xff },
-	{ 0x1319, 0xff },
-	{ 0x131a, 0xff },
-	{ 0x131b, 0xff },
-	{ 0x131c, 0xff },
-	{ 0x131e, 0xff },
-	{ 0x131f, 0xff },
-	{ 0x1320, 0xff },
-	{ 0x1b79, 0xff },
-	{ 0x1b7a, 0xff },
+	{ CS42L42_ADC_VOLUME, 0x9F },
+	{ CS42L42_OSC_SWITCH, 0x01 },
+	{ CS42L42_MCLK_CTL, 0x02 },
+	{ CS42L42_SRC_CTL, 0x03 },
+	{ CS42L42_MCLK_SRC_SEL, 0x00 },
+	{ CS42L42_ASP_FRM_CFG, 0x13 },
+	{ CS42L42_FSYNC_P_LOWER, 0xFF },
+	{ CS42L42_FSYNC_P_UPPER, 0x00 },
+	{ CS42L42_ASP_CLK_CFG, 0x20 },
+	{ CS42L42_SPDIF_CLK_CFG, 0x0D },
+	{ CS42L42_ASP_RX_DAI0_CH1_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH1_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH1_BIT_LSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH2_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH2_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH2_BIT_LSB, 0x20 },
+	{ CS42L42_ASP_RX_DAI0_CH3_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH3_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH3_BIT_LSB, 0x80 },
+	{ CS42L42_ASP_RX_DAI0_CH4_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH4_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH4_BIT_LSB, 0xA0 },
+	{ CS42L42_ASP_RX_DAI0_EN, 0x0C },
+	{ CS42L42_ASP_TX_CH_EN, 0x01 },
+	{ CS42L42_ASP_TX_CH_AP_RES, 0x02 },
+	{ CS42L42_ASP_TX_CH1_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_TX_CH1_BIT_LSB, 0x00 },
+	{ CS42L42_ASP_TX_SZ_EN, 0x01 },
+	{ CS42L42_PWR_CTL1, 0x0A },
+	{ CS42L42_PWR_CTL2, 0x84 },
+	{ CS42L42_MIXER_CHA_VOL, 0x3F },
+	{ CS42L42_MIXER_CHB_VOL, 0x3F },
+	{ CS42L42_MIXER_ADC_VOL, 0x3f },
+	{ CS42L42_HP_CTL, 0x03 },
+	{ CS42L42_MIC_DET_CTL1, 0xB6 },
+	{ CS42L42_TIPSENSE_CTL, 0xC2 },
+	{ CS42L42_HS_CLAMP_DISABLE, 0x01 },
+	{ CS42L42_HS_SWITCH_CTL, 0xF3 },
+	{ CS42L42_PWR_CTL3, 0x20 },
+	{ CS42L42_RSENSE_CTL2, 0x00 },
+	{ CS42L42_RSENSE_CTL3, 0x00 },
+	{ CS42L42_TSENSE_CTL, 0x80 },
+	{ CS42L42_HS_BIAS_CTL, 0xC0 },
+	{ CS42L42_PWR_CTL1, 0x02 },
+	{ CS42L42_ADC_OVFL_INT_MASK, 0xff },
+	{ CS42L42_MIXER_INT_MASK, 0xff },
+	{ CS42L42_SRC_INT_MASK, 0xff },
+	{ CS42L42_ASP_RX_INT_MASK, 0xff },
+	{ CS42L42_ASP_TX_INT_MASK, 0xff },
+	{ CS42L42_CODEC_INT_MASK, 0xff },
+	{ CS42L42_SRCPL_INT_MASK, 0xff },
+	{ CS42L42_VPMON_INT_MASK, 0xff },
+	{ CS42L42_PLL_LOCK_INT_MASK, 0xff },
+	{ CS42L42_TSRS_PLUG_INT_MASK, 0xff },
+	{ CS42L42_DET_INT1_MASK, 0xff },
+	{ CS42L42_DET_INT2_MASK, 0xff },
 };
 
 /* Vendor specific hw configuration for CS8409 */
@@ -281,115 +288,115 @@
 
 /* Vendor specific HW configuration for CS42L42 */
 static const struct cs8409_i2c_param dolphin_c0_init_reg_seq[] = {
-	{ 0x1010, 0xB0 },
-	{ 0x1D01, 0x00 },
+	{ CS42L42_I2C_TIMEOUT, 0xB0 },
+	{ CS42L42_ADC_CTL, 0x00 },
 	{ 0x1D02, 0x06 },
-	{ 0x1D03, 0x9F },
-	{ 0x1107, 0x01 },
-	{ 0x1009, 0x02 },
-	{ 0x1007, 0x03 },
-	{ 0x1201, 0x00 },
-	{ 0x1208, 0x13 },
-	{ 0x1205, 0xFF },
-	{ 0x1206, 0x00 },
-	{ 0x1207, 0x20 },
-	{ 0x1202, 0x0D },
-	{ 0x2A02, 0x02 },
-	{ 0x2A03, 0x00 },
-	{ 0x2A04, 0x00 },
-	{ 0x2A05, 0x02 },
-	{ 0x2A06, 0x00 },
-	{ 0x2A07, 0x20 },
-	{ 0x2A01, 0x0C },
-	{ 0x2902, 0x01 },
-	{ 0x2903, 0x02 },
-	{ 0x2904, 0x00 },
-	{ 0x2905, 0x00 },
-	{ 0x2901, 0x01 },
-	{ 0x1101, 0x0A },
-	{ 0x1102, 0x84 },
-	{ 0x2001, 0x03 },
-	{ 0x2301, 0x3F },
-	{ 0x2303, 0x3F },
-	{ 0x2302, 0x3f },
-	{ 0x1B75, 0xB6 },
-	{ 0x1B73, 0xC2 },
-	{ 0x1129, 0x01 },
-	{ 0x1121, 0xF3 },
-	{ 0x1103, 0x20 },
-	{ 0x1105, 0x00 },
-	{ 0x1112, 0x00 },
-	{ 0x1113, 0x80 },
-	{ 0x1C03, 0xC0 },
-	{ 0x1101, 0x02 },
-	{ 0x1316, 0xff },
-	{ 0x1317, 0xff },
-	{ 0x1318, 0xff },
-	{ 0x1319, 0xff },
-	{ 0x131a, 0xff },
-	{ 0x131b, 0xff },
-	{ 0x131c, 0xff },
-	{ 0x131e, 0xff },
-	{ 0x131f, 0xff },
-	{ 0x1320, 0xff },
-	{ 0x1b79, 0xff },
-	{ 0x1b7a, 0xff }
+	{ CS42L42_ADC_VOLUME, 0x9F },
+	{ CS42L42_OSC_SWITCH, 0x01 },
+	{ CS42L42_MCLK_CTL, 0x02 },
+	{ CS42L42_SRC_CTL, 0x03 },
+	{ CS42L42_MCLK_SRC_SEL, 0x00 },
+	{ CS42L42_ASP_FRM_CFG, 0x13 },
+	{ CS42L42_FSYNC_P_LOWER, 0xFF },
+	{ CS42L42_FSYNC_P_UPPER, 0x00 },
+	{ CS42L42_ASP_CLK_CFG, 0x20 },
+	{ CS42L42_SPDIF_CLK_CFG, 0x0D },
+	{ CS42L42_ASP_RX_DAI0_CH1_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH1_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH1_BIT_LSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH2_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH2_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH2_BIT_LSB, 0x20 },
+	{ CS42L42_ASP_RX_DAI0_EN, 0x0C },
+	{ CS42L42_ASP_TX_CH_EN, 0x01 },
+	{ CS42L42_ASP_TX_CH_AP_RES, 0x02 },
+	{ CS42L42_ASP_TX_CH1_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_TX_CH1_BIT_LSB, 0x00 },
+	{ CS42L42_ASP_TX_SZ_EN, 0x01 },
+	{ CS42L42_PWR_CTL1, 0x0A },
+	{ CS42L42_PWR_CTL2, 0x84 },
+	{ CS42L42_HP_CTL, 0x03 },
+	{ CS42L42_MIXER_CHA_VOL, 0x3F },
+	{ CS42L42_MIXER_CHB_VOL, 0x3F },
+	{ CS42L42_MIXER_ADC_VOL, 0x3f },
+	{ CS42L42_MIC_DET_CTL1, 0xB6 },
+	{ CS42L42_TIPSENSE_CTL, 0xC2 },
+	{ CS42L42_HS_CLAMP_DISABLE, 0x01 },
+	{ CS42L42_HS_SWITCH_CTL, 0xF3 },
+	{ CS42L42_PWR_CTL3, 0x20 },
+	{ CS42L42_RSENSE_CTL2, 0x00 },
+	{ CS42L42_RSENSE_CTL3, 0x00 },
+	{ CS42L42_TSENSE_CTL, 0x80 },
+	{ CS42L42_HS_BIAS_CTL, 0xC0 },
+	{ CS42L42_PWR_CTL1, 0x02 },
+	{ CS42L42_ADC_OVFL_INT_MASK, 0xff },
+	{ CS42L42_MIXER_INT_MASK, 0xff },
+	{ CS42L42_SRC_INT_MASK, 0xff },
+	{ CS42L42_ASP_RX_INT_MASK, 0xff },
+	{ CS42L42_ASP_TX_INT_MASK, 0xff },
+	{ CS42L42_CODEC_INT_MASK, 0xff },
+	{ CS42L42_SRCPL_INT_MASK, 0xff },
+	{ CS42L42_VPMON_INT_MASK, 0xff },
+	{ CS42L42_PLL_LOCK_INT_MASK, 0xff },
+	{ CS42L42_TSRS_PLUG_INT_MASK, 0xff },
+	{ CS42L42_DET_INT1_MASK, 0xff },
+	{ CS42L42_DET_INT2_MASK, 0xff }
 };
 
 static const struct cs8409_i2c_param dolphin_c1_init_reg_seq[] = {
-	{ 0x1010, 0xB0 },
-	{ 0x1D01, 0x00 },
+	{ CS42L42_I2C_TIMEOUT, 0xB0 },
+	{ CS42L42_ADC_CTL, 0x00 },
 	{ 0x1D02, 0x06 },
-	{ 0x1D03, 0x9F },
-	{ 0x1107, 0x01 },
-	{ 0x1009, 0x02 },
-	{ 0x1007, 0x03 },
-	{ 0x1201, 0x00 },
-	{ 0x1208, 0x13 },
-	{ 0x1205, 0xFF },
-	{ 0x1206, 0x00 },
-	{ 0x1207, 0x20 },
-	{ 0x1202, 0x0D },
-	{ 0x2A02, 0x02 },
-	{ 0x2A03, 0x00 },
-	{ 0x2A04, 0x80 },
-	{ 0x2A05, 0x02 },
-	{ 0x2A06, 0x00 },
-	{ 0x2A07, 0xA0 },
-	{ 0x2A01, 0x0C },
-	{ 0x2902, 0x00 },
-	{ 0x2903, 0x02 },
-	{ 0x2904, 0x00 },
-	{ 0x2905, 0x00 },
-	{ 0x2901, 0x00 },
-	{ 0x1101, 0x0E },
-	{ 0x1102, 0x84 },
-	{ 0x2001, 0x01 },
-	{ 0x2301, 0x3F },
-	{ 0x2303, 0x3F },
-	{ 0x2302, 0x3f },
-	{ 0x1B75, 0xB6 },
-	{ 0x1B73, 0xC2 },
-	{ 0x1129, 0x01 },
-	{ 0x1121, 0xF3 },
-	{ 0x1103, 0x20 },
-	{ 0x1105, 0x00 },
-	{ 0x1112, 0x00 },
-	{ 0x1113, 0x80 },
-	{ 0x1C03, 0xC0 },
-	{ 0x1101, 0x06 },
-	{ 0x1316, 0xff },
-	{ 0x1317, 0xff },
-	{ 0x1318, 0xff },
-	{ 0x1319, 0xff },
-	{ 0x131a, 0xff },
-	{ 0x131b, 0xff },
-	{ 0x131c, 0xff },
-	{ 0x131e, 0xff },
-	{ 0x131f, 0xff },
-	{ 0x1320, 0xff },
-	{ 0x1b79, 0xff },
-	{ 0x1b7a, 0xff }
+	{ CS42L42_ADC_VOLUME, 0x9F },
+	{ CS42L42_OSC_SWITCH, 0x01 },
+	{ CS42L42_MCLK_CTL, 0x02 },
+	{ CS42L42_SRC_CTL, 0x03 },
+	{ CS42L42_MCLK_SRC_SEL, 0x00 },
+	{ CS42L42_ASP_FRM_CFG, 0x13 },
+	{ CS42L42_FSYNC_P_LOWER, 0xFF },
+	{ CS42L42_FSYNC_P_UPPER, 0x00 },
+	{ CS42L42_ASP_CLK_CFG, 0x20 },
+	{ CS42L42_SPDIF_CLK_CFG, 0x0D },
+	{ CS42L42_ASP_RX_DAI0_CH1_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH1_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH1_BIT_LSB, 0x80 },
+	{ CS42L42_ASP_RX_DAI0_CH2_AP_RES, 0x02 },
+	{ CS42L42_ASP_RX_DAI0_CH2_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_RX_DAI0_CH2_BIT_LSB, 0xA0 },
+	{ CS42L42_ASP_RX_DAI0_EN, 0x0C },
+	{ CS42L42_ASP_TX_CH_EN, 0x00 },
+	{ CS42L42_ASP_TX_CH_AP_RES, 0x02 },
+	{ CS42L42_ASP_TX_CH1_BIT_MSB, 0x00 },
+	{ CS42L42_ASP_TX_CH1_BIT_LSB, 0x00 },
+	{ CS42L42_ASP_TX_SZ_EN, 0x00 },
+	{ CS42L42_PWR_CTL1, 0x0E },
+	{ CS42L42_PWR_CTL2, 0x84 },
+	{ CS42L42_HP_CTL, 0x01 },
+	{ CS42L42_MIXER_CHA_VOL, 0x3F },
+	{ CS42L42_MIXER_CHB_VOL, 0x3F },
+	{ CS42L42_MIXER_ADC_VOL, 0x3f },
+	{ CS42L42_MIC_DET_CTL1, 0xB6 },
+	{ CS42L42_TIPSENSE_CTL, 0xC2 },
+	{ CS42L42_HS_CLAMP_DISABLE, 0x01 },
+	{ CS42L42_HS_SWITCH_CTL, 0xF3 },
+	{ CS42L42_PWR_CTL3, 0x20 },
+	{ CS42L42_RSENSE_CTL2, 0x00 },
+	{ CS42L42_RSENSE_CTL3, 0x00 },
+	{ CS42L42_TSENSE_CTL, 0x80 },
+	{ CS42L42_HS_BIAS_CTL, 0xC0 },
+	{ CS42L42_PWR_CTL1, 0x06 },
+	{ CS42L42_ADC_OVFL_INT_MASK, 0xff },
+	{ CS42L42_MIXER_INT_MASK, 0xff },
+	{ CS42L42_SRC_INT_MASK, 0xff },
+	{ CS42L42_ASP_RX_INT_MASK, 0xff },
+	{ CS42L42_ASP_TX_INT_MASK, 0xff },
+	{ CS42L42_CODEC_INT_MASK, 0xff },
+	{ CS42L42_SRCPL_INT_MASK, 0xff },
+	{ CS42L42_VPMON_INT_MASK, 0xff },
+	{ CS42L42_PLL_LOCK_INT_MASK, 0xff },
+	{ CS42L42_TSRS_PLUG_INT_MASK, 0xff },
+	{ CS42L42_DET_INT1_MASK, 0xff },
+	{ CS42L42_DET_INT2_MASK, 0xff }
 };
 
 /* Vendor specific hw configuration for CS8409 */
@@ -475,26 +482,29 @@
 	SND_PCI_QUIRK(0x1028, 0x0A29, "Bullseye", CS8409_BULLSEYE),
 	SND_PCI_QUIRK(0x1028, 0x0A2A, "Bullseye", CS8409_BULLSEYE),
 	SND_PCI_QUIRK(0x1028, 0x0A2B, "Bullseye", CS8409_BULLSEYE),
+	SND_PCI_QUIRK(0x1028, 0x0A77, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A78, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A79, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A7A, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A7D, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A7E, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A7F, "Cyborg", CS8409_CYBORG),
+	SND_PCI_QUIRK(0x1028, 0x0A80, "Cyborg", CS8409_CYBORG),
 	SND_PCI_QUIRK(0x1028, 0x0AB0, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0AB2, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0AB1, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0AB3, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0AB4, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0AB5, "Warlock", CS8409_WARLOCK),
+	SND_PCI_QUIRK(0x1028, 0x0ACF, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0AD0, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0AD1, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0AD2, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0AD3, "Dolphin", CS8409_DOLPHIN),
 	SND_PCI_QUIRK(0x1028, 0x0AD9, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0ADA, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0ADB, "Warlock", CS8409_WARLOCK),
 	SND_PCI_QUIRK(0x1028, 0x0ADC, "Warlock", CS8409_WARLOCK),
-	SND_PCI_QUIRK(0x1028, 0x0AF4, "Warlock", CS8409_WARLOCK),
-	SND_PCI_QUIRK(0x1028, 0x0AF5, "Warlock", CS8409_WARLOCK),
-	SND_PCI_QUIRK(0x1028, 0x0A77, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A78, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A79, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A7A, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A7D, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A7E, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A7F, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0A80, "Cyborg", CS8409_CYBORG),
 	SND_PCI_QUIRK(0x1028, 0x0ADF, "Cyborg", CS8409_CYBORG),
 	SND_PCI_QUIRK(0x1028, 0x0AE0, "Cyborg", CS8409_CYBORG),
 	SND_PCI_QUIRK(0x1028, 0x0AE1, "Cyborg", CS8409_CYBORG),
@@ -507,11 +517,35 @@
 	SND_PCI_QUIRK(0x1028, 0x0AEE, "Cyborg", CS8409_CYBORG),
 	SND_PCI_QUIRK(0x1028, 0x0AEF, "Cyborg", CS8409_CYBORG),
 	SND_PCI_QUIRK(0x1028, 0x0AF0, "Cyborg", CS8409_CYBORG),
-	SND_PCI_QUIRK(0x1028, 0x0AD0, "Dolphin", CS8409_DOLPHIN),
-	SND_PCI_QUIRK(0x1028, 0x0AD1, "Dolphin", CS8409_DOLPHIN),
-	SND_PCI_QUIRK(0x1028, 0x0AD2, "Dolphin", CS8409_DOLPHIN),
-	SND_PCI_QUIRK(0x1028, 0x0AD3, "Dolphin", CS8409_DOLPHIN),
-	SND_PCI_QUIRK(0x1028, 0x0ACF, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0AF4, "Warlock", CS8409_WARLOCK),
+	SND_PCI_QUIRK(0x1028, 0x0AF5, "Warlock", CS8409_WARLOCK),
+	SND_PCI_QUIRK(0x1028, 0x0B92, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0B93, "Warlock MLK Dual Mic", CS8409_WARLOCK_MLK_DUAL_MIC),
+	SND_PCI_QUIRK(0x1028, 0x0B94, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0B95, "Warlock MLK Dual Mic", CS8409_WARLOCK_MLK_DUAL_MIC),
+	SND_PCI_QUIRK(0x1028, 0x0B96, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0B97, "Warlock MLK Dual Mic", CS8409_WARLOCK_MLK_DUAL_MIC),
+	SND_PCI_QUIRK(0x1028, 0x0BA5, "Odin", CS8409_ODIN),
+	SND_PCI_QUIRK(0x1028, 0x0BA6, "Odin", CS8409_ODIN),
+	SND_PCI_QUIRK(0x1028, 0x0BA8, "Odin", CS8409_ODIN),
+	SND_PCI_QUIRK(0x1028, 0x0BAA, "Odin", CS8409_ODIN),
+	SND_PCI_QUIRK(0x1028, 0x0BAE, "Odin", CS8409_ODIN),
+	SND_PCI_QUIRK(0x1028, 0x0BB2, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0BB3, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0BB4, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0BB5, "Warlock N3 15 TGL-U Nuvoton EC", CS8409_WARLOCK),
+	SND_PCI_QUIRK(0x1028, 0x0BB6, "Warlock V3 15 TGL-U Nuvoton EC", CS8409_WARLOCK),
+	SND_PCI_QUIRK(0x1028, 0x0BB8, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0BB9, "Warlock MLK Dual Mic", CS8409_WARLOCK_MLK_DUAL_MIC),
+	SND_PCI_QUIRK(0x1028, 0x0BBA, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0BBB, "Warlock MLK Dual Mic", CS8409_WARLOCK_MLK_DUAL_MIC),
+	SND_PCI_QUIRK(0x1028, 0x0BBC, "Warlock MLK", CS8409_WARLOCK_MLK),
+	SND_PCI_QUIRK(0x1028, 0x0BBD, "Warlock MLK Dual Mic", CS8409_WARLOCK_MLK_DUAL_MIC),
+	SND_PCI_QUIRK(0x1028, 0x0BD4, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0BD5, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0BD6, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0BD7, "Dolphin", CS8409_DOLPHIN),
+	SND_PCI_QUIRK(0x1028, 0x0BD8, "Dolphin", CS8409_DOLPHIN),
 	{} /* terminator */
 };
 
@@ -519,8 +553,11 @@
 const struct hda_model_fixup cs8409_models[] = {
 	{ .id = CS8409_BULLSEYE, .name = "bullseye" },
 	{ .id = CS8409_WARLOCK, .name = "warlock" },
+	{ .id = CS8409_WARLOCK_MLK, .name = "warlock mlk" },
+	{ .id = CS8409_WARLOCK_MLK_DUAL_MIC, .name = "warlock mlk dual mic" },
 	{ .id = CS8409_CYBORG, .name = "cyborg" },
 	{ .id = CS8409_DOLPHIN, .name = "dolphin" },
+	{ .id = CS8409_ODIN, .name = "odin" },
 	{}
 };
 
@@ -537,6 +574,18 @@
 		.chained = true,
 		.chain_id = CS8409_FIXUPS,
 	},
+	[CS8409_WARLOCK_MLK] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = cs8409_cs42l42_pincfgs,
+		.chained = true,
+		.chain_id = CS8409_FIXUPS,
+	},
+	[CS8409_WARLOCK_MLK_DUAL_MIC] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = cs8409_cs42l42_pincfgs,
+		.chained = true,
+		.chain_id = CS8409_FIXUPS,
+	},
 	[CS8409_CYBORG] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = cs8409_cs42l42_pincfgs,
@@ -557,4 +606,10 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = dolphin_fixups,
 	},
+	[CS8409_ODIN] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = cs8409_cs42l42_pincfgs_no_dmic,
+		.chained = true,
+		.chain_id = CS8409_FIXUPS,
+	},
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_cs8409.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_cs8409.c
@@ -419,6 +419,39 @@
 	snd_hda_override_wcaps(codec, nid, (get_wcaps(codec, nid) | AC_WCAP_UNSOL_CAP));
 }
 
+static int cs8409_spk_sw_gpio_get(struct snd_kcontrol *kcontrol,
+				 struct snd_ctl_elem_value *ucontrol)
+{
+	struct hda_codec *codec = snd_kcontrol_chip(kcontrol);
+	struct cs8409_spec *spec = codec->spec;
+
+	ucontrol->value.integer.value[0] = !!(spec->gpio_data & spec->speaker_pdn_gpio);
+	return 0;
+}
+
+static int cs8409_spk_sw_gpio_put(struct snd_kcontrol *kcontrol,
+				 struct snd_ctl_elem_value *ucontrol)
+{
+	struct hda_codec *codec = snd_kcontrol_chip(kcontrol);
+	struct cs8409_spec *spec = codec->spec;
+	unsigned int gpio_data;
+
+	gpio_data = (spec->gpio_data & ~spec->speaker_pdn_gpio) |
+		(ucontrol->value.integer.value[0] ? spec->speaker_pdn_gpio : 0);
+	if (gpio_data == spec->gpio_data)
+		return 0;
+	spec->gpio_data = gpio_data;
+	snd_hda_codec_write(codec, CS8409_PIN_AFG, 0, AC_VERB_SET_GPIO_DATA, spec->gpio_data);
+	return 1;
+}
+
+static const struct snd_kcontrol_new cs8409_spk_sw_ctrl = {
+	.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
+	.info = snd_ctl_boolean_mono_info,
+	.get = cs8409_spk_sw_gpio_get,
+	.put = cs8409_spk_sw_gpio_put,
+};
+
 /******************************************************************************
  *                        CS42L42 Specific Functions
  ******************************************************************************/
@@ -481,26 +514,26 @@
 	if (mute) {
 		if (vol_type == CS42L42_VOL_DAC) {
 			if (chs & BIT(0))
-				cs8409_i2c_write(cs42l42, CS42L42_REG_HS_VOL_CHA, 0x3f);
+				cs8409_i2c_write(cs42l42, CS42L42_MIXER_CHA_VOL, 0x3f);
 			if (chs & BIT(1))
-				cs8409_i2c_write(cs42l42, CS42L42_REG_HS_VOL_CHB, 0x3f);
+				cs8409_i2c_write(cs42l42, CS42L42_MIXER_CHB_VOL, 0x3f);
 		} else if (vol_type == CS42L42_VOL_ADC) {
 			if (chs & BIT(0))
-				cs8409_i2c_write(cs42l42, CS42L42_REG_AMIC_VOL, 0x9f);
+				cs8409_i2c_write(cs42l42, CS42L42_ADC_VOLUME, 0x9f);
 		}
 	} else {
 		if (vol_type == CS42L42_VOL_DAC) {
 			if (chs & BIT(0))
-				cs8409_i2c_write(cs42l42, CS42L42_REG_HS_VOL_CHA,
+				cs8409_i2c_write(cs42l42, CS42L42_MIXER_CHA_VOL,
 					-(cs42l42->vol[CS42L42_DAC_CH0_VOL_OFFSET])
-					& CS42L42_REG_HS_VOL_MASK);
+					& CS42L42_MIXER_CH_VOL_MASK);
 			if (chs & BIT(1))
-				cs8409_i2c_write(cs42l42, CS42L42_REG_HS_VOL_CHB,
+				cs8409_i2c_write(cs42l42, CS42L42_MIXER_CHB_VOL,
 					-(cs42l42->vol[CS42L42_DAC_CH1_VOL_OFFSET])
-					& CS42L42_REG_HS_VOL_MASK);
+					& CS42L42_MIXER_CH_VOL_MASK);
 		} else if (vol_type == CS42L42_VOL_ADC) {
 			if (chs & BIT(0))
-				cs8409_i2c_write(cs42l42, CS42L42_REG_AMIC_VOL,
+				cs8409_i2c_write(cs42l42, CS42L42_ADC_VOLUME,
 					cs42l42->vol[CS42L42_ADC_VOL_OFFSET]
 					& CS42L42_REG_AMIC_VOL_MASK);
 		}
@@ -601,37 +634,131 @@
 /* Configure CS42L42 slave codec for jack autodetect */
 static void cs42l42_enable_jack_detect(struct sub_codec *cs42l42)
 {
-	cs8409_i2c_write(cs42l42, 0x1b70, cs42l42->hsbias_hiz);
+	cs8409_i2c_write(cs42l42, CS42L42_HSBIAS_SC_AUTOCTL, cs42l42->hsbias_hiz);
 	/* Clear WAKE# */
-	cs8409_i2c_write(cs42l42, 0x1b71, 0x00C1);
+	cs8409_i2c_write(cs42l42, CS42L42_WAKE_CTL, 0x00C1);
 	/* Wait ~2.5ms */
 	usleep_range(2500, 3000);
 	/* Set mode WAKE# output follows the combination logic directly */
-	cs8409_i2c_write(cs42l42, 0x1b71, 0x00C0);
+	cs8409_i2c_write(cs42l42, CS42L42_WAKE_CTL, 0x00C0);
 	/* Clear interrupts status */
-	cs8409_i2c_read(cs42l42, 0x130f);
+	cs8409_i2c_read(cs42l42, CS42L42_TSRS_PLUG_STATUS);
 	/* Enable interrupt */
-	cs8409_i2c_write(cs42l42, 0x1320, 0xF3);
+	cs8409_i2c_write(cs42l42, CS42L42_TSRS_PLUG_INT_MASK, 0xF3);
 }
 
 /* Enable and run CS42L42 slave codec jack auto detect */
 static void cs42l42_run_jack_detect(struct sub_codec *cs42l42)
 {
 	/* Clear interrupts */
-	cs8409_i2c_read(cs42l42, 0x1308);
-	cs8409_i2c_read(cs42l42, 0x1b77);
-	cs8409_i2c_write(cs42l42, 0x1320, 0xFF);
-	cs8409_i2c_read(cs42l42, 0x130f);
-
-	cs8409_i2c_write(cs42l42, 0x1102, 0x87);
-	cs8409_i2c_write(cs42l42, 0x1f06, 0x86);
-	cs8409_i2c_write(cs42l42, 0x1b74, 0x07);
-	cs8409_i2c_write(cs42l42, 0x131b, 0xFD);
-	cs8409_i2c_write(cs42l42, 0x1120, 0x80);
-	/* Wait ~100us*/
-	usleep_range(100, 200);
-	cs8409_i2c_write(cs42l42, 0x111f, 0x77);
-	cs8409_i2c_write(cs42l42, 0x1120, 0xc0);
+	cs8409_i2c_read(cs42l42, CS42L42_CODEC_STATUS);
+	cs8409_i2c_read(cs42l42, CS42L42_DET_STATUS1);
+	cs8409_i2c_write(cs42l42, CS42L42_TSRS_PLUG_INT_MASK, 0xFF);
+	cs8409_i2c_read(cs42l42, CS42L42_TSRS_PLUG_STATUS);
+
+	cs8409_i2c_write(cs42l42, CS42L42_PWR_CTL2, 0x87);
+	cs8409_i2c_write(cs42l42, CS42L42_DAC_CTL2, 0x86);
+	cs8409_i2c_write(cs42l42, CS42L42_MISC_DET_CTL, 0x07);
+	cs8409_i2c_write(cs42l42, CS42L42_CODEC_INT_MASK, 0xFD);
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL2, 0x80);
+	/* Wait ~20ms*/
+	usleep_range(20000, 25000);
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL1, 0x77);
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL2, 0xc0);
+}
+
+static int cs42l42_manual_hs_det(struct sub_codec *cs42l42)
+{
+	unsigned int hs_det_status;
+	unsigned int hs_det_comp1;
+	unsigned int hs_det_comp2;
+	unsigned int hs_det_sw;
+	unsigned int hs_type;
+
+	/* Set hs detect to manual, active mode */
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL2,
+			 (1 << CS42L42_HSDET_CTRL_SHIFT) |
+			 (0 << CS42L42_HSDET_SET_SHIFT) |
+			 (0 << CS42L42_HSBIAS_REF_SHIFT) |
+			 (0 << CS42L42_HSDET_AUTO_TIME_SHIFT));
+
+	/* Configure HS DET comparator reference levels. */
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL1,
+			 (CS42L42_HSDET_COMP1_LVL_VAL << CS42L42_HSDET_COMP1_LVL_SHIFT) |
+			 (CS42L42_HSDET_COMP2_LVL_VAL << CS42L42_HSDET_COMP2_LVL_SHIFT));
+
+	/* Open the SW_HSB_HS3 switch and close SW_HSB_HS4 for a Type 1 headset. */
+	cs8409_i2c_write(cs42l42, CS42L42_HS_SWITCH_CTL, CS42L42_HSDET_SW_COMP1);
+
+	msleep(100);
+
+	hs_det_status = cs8409_i2c_read(cs42l42, CS42L42_HS_DET_STATUS);
+
+	hs_det_comp1 = (hs_det_status & CS42L42_HSDET_COMP1_OUT_MASK) >>
+			CS42L42_HSDET_COMP1_OUT_SHIFT;
+	hs_det_comp2 = (hs_det_status & CS42L42_HSDET_COMP2_OUT_MASK) >>
+			CS42L42_HSDET_COMP2_OUT_SHIFT;
+
+	/* Close the SW_HSB_HS3 switch for a Type 2 headset. */
+	cs8409_i2c_write(cs42l42, CS42L42_HS_SWITCH_CTL, CS42L42_HSDET_SW_COMP2);
+
+	msleep(100);
+
+	hs_det_status = cs8409_i2c_read(cs42l42, CS42L42_HS_DET_STATUS);
+
+	hs_det_comp1 |= ((hs_det_status & CS42L42_HSDET_COMP1_OUT_MASK) >>
+			CS42L42_HSDET_COMP1_OUT_SHIFT) << 1;
+	hs_det_comp2 |= ((hs_det_status & CS42L42_HSDET_COMP2_OUT_MASK) >>
+			CS42L42_HSDET_COMP2_OUT_SHIFT) << 1;
+
+	/* Use Comparator 1 with 1.25V Threshold. */
+	switch (hs_det_comp1) {
+	case CS42L42_HSDET_COMP_TYPE1:
+		hs_type = CS42L42_PLUG_CTIA;
+		hs_det_sw = CS42L42_HSDET_SW_TYPE1;
+		break;
+	case CS42L42_HSDET_COMP_TYPE2:
+		hs_type = CS42L42_PLUG_OMTP;
+		hs_det_sw = CS42L42_HSDET_SW_TYPE2;
+		break;
+	default:
+		/* Fallback to Comparator 2 with 1.75V Threshold. */
+		switch (hs_det_comp2) {
+		case CS42L42_HSDET_COMP_TYPE1:
+			hs_type = CS42L42_PLUG_CTIA;
+			hs_det_sw = CS42L42_HSDET_SW_TYPE1;
+			break;
+		case CS42L42_HSDET_COMP_TYPE2:
+			hs_type = CS42L42_PLUG_OMTP;
+			hs_det_sw = CS42L42_HSDET_SW_TYPE2;
+			break;
+		case CS42L42_HSDET_COMP_TYPE3:
+			hs_type = CS42L42_PLUG_HEADPHONE;
+			hs_det_sw = CS42L42_HSDET_SW_TYPE3;
+			break;
+		default:
+			hs_type = CS42L42_PLUG_INVALID;
+			hs_det_sw = CS42L42_HSDET_SW_TYPE4;
+			break;
+		}
+	}
+
+	/* Set Switches */
+	cs8409_i2c_write(cs42l42, CS42L42_HS_SWITCH_CTL, hs_det_sw);
+
+	/* Set HSDET mode to Manual—Disabled */
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL2,
+			 (0 << CS42L42_HSDET_CTRL_SHIFT) |
+			 (0 << CS42L42_HSDET_SET_SHIFT) |
+			 (0 << CS42L42_HSBIAS_REF_SHIFT) |
+			 (0 << CS42L42_HSDET_AUTO_TIME_SHIFT));
+
+	/* Configure HS DET comparator reference levels. */
+	cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL1,
+			 (CS42L42_HSDET_COMP1_LVL_DEFAULT << CS42L42_HSDET_COMP1_LVL_SHIFT) |
+			 (CS42L42_HSDET_COMP2_LVL_DEFAULT << CS42L42_HSDET_COMP2_LVL_SHIFT));
+
+	return hs_type;
 }
 
 static int cs42l42_handle_tip_sense(struct sub_codec *cs42l42, unsigned int reg_ts_status)
@@ -640,35 +767,34 @@
 
 	/* TIP_SENSE INSERT/REMOVE */
 	switch (reg_ts_status) {
-	case CS42L42_JACK_INSERTED:
-		if (!cs42l42->hp_jack_in) {
-			if (cs42l42->no_type_dect) {
-				status_changed = 1;
-				cs42l42->hp_jack_in = 1;
-				cs42l42->mic_jack_in = 0;
-			} else {
-				cs42l42_run_jack_detect(cs42l42);
-			}
-		}
-		break;
-
-	case CS42L42_JACK_REMOVED:
-		if (cs42l42->hp_jack_in || cs42l42->mic_jack_in) {
+	case CS42L42_TS_PLUG:
+		if (cs42l42->no_type_dect) {
 			status_changed = 1;
-			cs42l42->hp_jack_in = 0;
+			cs42l42->hp_jack_in = 1;
 			cs42l42->mic_jack_in = 0;
+		} else {
+			cs42l42_run_jack_detect(cs42l42);
 		}
 		break;
+
+	case CS42L42_TS_UNPLUG:
+		status_changed = 1;
+		cs42l42->hp_jack_in = 0;
+		cs42l42->mic_jack_in = 0;
+		break;
 	default:
 		/* jack in transition */
 		break;
 	}
 
+	codec_dbg(cs42l42->codec, "Tip Sense Detection: (%d)\n", reg_ts_status);
+
 	return status_changed;
 }
 
 static int cs42l42_jack_unsol_event(struct sub_codec *cs42l42)
 {
+	int current_plug_status;
 	int status_changed = 0;
 	int reg_cdc_status;
 	int reg_hs_status;
@@ -676,46 +802,65 @@
 	int type;
 
 	/* Read jack detect status registers */
-	reg_cdc_status = cs8409_i2c_read(cs42l42, 0x1308);
-	reg_hs_status = cs8409_i2c_read(cs42l42, 0x1124);
-	reg_ts_status = cs8409_i2c_read(cs42l42, 0x130f);
+	reg_cdc_status = cs8409_i2c_read(cs42l42, CS42L42_CODEC_STATUS);
+	reg_hs_status = cs8409_i2c_read(cs42l42, CS42L42_HS_DET_STATUS);
+	reg_ts_status = cs8409_i2c_read(cs42l42, CS42L42_TSRS_PLUG_STATUS);
 
 	/* If status values are < 0, read error has occurred. */
 	if (reg_cdc_status < 0 || reg_hs_status < 0 || reg_ts_status < 0)
 		return -EIO;
 
+	current_plug_status = (reg_ts_status & (CS42L42_TS_PLUG_MASK | CS42L42_TS_UNPLUG_MASK))
+				>> CS42L42_TS_PLUG_SHIFT;
+
 	/* HSDET_AUTO_DONE */
-	if (reg_cdc_status & CS42L42_HSDET_AUTO_DONE) {
+	if (reg_cdc_status & CS42L42_HSDET_AUTO_DONE_MASK) {
 
 		/* Disable HSDET_AUTO_DONE */
-		cs8409_i2c_write(cs42l42, 0x131b, 0xFF);
+		cs8409_i2c_write(cs42l42, CS42L42_CODEC_INT_MASK, 0xFF);
 
-		type = ((reg_hs_status & CS42L42_HSTYPE_MASK) + 1);
+		type = (reg_hs_status & CS42L42_HSDET_TYPE_MASK) >> CS42L42_HSDET_TYPE_SHIFT;
+
+		/* Configure the HSDET mode. */
+		cs8409_i2c_write(cs42l42, CS42L42_HSDET_CTL2, 0x80);
 
 		if (cs42l42->no_type_dect) {
-			status_changed = cs42l42_handle_tip_sense(cs42l42, reg_ts_status);
-		} else if (type == 4) {
-			/* Type 4 not supported	*/
-			status_changed = cs42l42_handle_tip_sense(cs42l42, CS42L42_JACK_REMOVED);
+			status_changed = cs42l42_handle_tip_sense(cs42l42, current_plug_status);
 		} else {
-			if (!cs42l42->hp_jack_in) {
-				status_changed = 1;
-				cs42l42->hp_jack_in = 1;
+			if (type == CS42L42_PLUG_INVALID || type == CS42L42_PLUG_HEADPHONE) {
+				codec_dbg(cs42l42->codec,
+					  "Auto detect value not valid (%d), running manual det\n",
+					  type);
+				type = cs42l42_manual_hs_det(cs42l42);
 			}
-			/* type = 3 has no mic */
-			if ((!cs42l42->mic_jack_in) && (type != 3)) {
+
+			switch (type) {
+			case CS42L42_PLUG_CTIA:
+			case CS42L42_PLUG_OMTP:
 				status_changed = 1;
+				cs42l42->hp_jack_in = 1;
 				cs42l42->mic_jack_in = 1;
+				break;
+			case CS42L42_PLUG_HEADPHONE:
+				status_changed = 1;
+				cs42l42->hp_jack_in = 1;
+				cs42l42->mic_jack_in = 0;
+				break;
+			default:
+				status_changed = 1;
+				cs42l42->hp_jack_in = 0;
+				cs42l42->mic_jack_in = 0;
+				break;
 			}
+			codec_dbg(cs42l42->codec, "Detection done (%d)\n", type);
 		}
-		/* Configure the HSDET mode. */
-		cs8409_i2c_write(cs42l42, 0x1120, 0x80);
+
 		/* Enable the HPOUT ground clamp and configure the HP pull-down */
-		cs8409_i2c_write(cs42l42, 0x1F06, 0x02);
+		cs8409_i2c_write(cs42l42, CS42L42_DAC_CTL2, 0x02);
 		/* Re-Enable Tip Sense Interrupt */
-		cs8409_i2c_write(cs42l42, 0x1320, 0xF3);
+		cs8409_i2c_write(cs42l42, CS42L42_TSRS_PLUG_INT_MASK, 0xF3);
 	} else {
-		status_changed = cs42l42_handle_tip_sense(cs42l42, reg_ts_status);
+		status_changed = cs42l42_handle_tip_sense(cs42l42, current_plug_status);
 	}
 
 	return status_changed;
@@ -724,31 +869,42 @@
 static void cs42l42_resume(struct sub_codec *cs42l42)
 {
 	struct hda_codec *codec = cs42l42->codec;
-	unsigned int gpio_data;
+	struct cs8409_spec *spec = codec->spec;
 	struct cs8409_i2c_param irq_regs[] = {
-		{ 0x1308, 0x00 },
-		{ 0x1309, 0x00 },
-		{ 0x130A, 0x00 },
-		{ 0x130F, 0x00 },
+		{ CS42L42_CODEC_STATUS, 0x00 },
+		{ CS42L42_DET_INT_STATUS1, 0x00 },
+		{ CS42L42_DET_INT_STATUS2, 0x00 },
+		{ CS42L42_TSRS_PLUG_STATUS, 0x00 },
 	};
+	int fsv_old, fsv_new;
 
 	/* Bring CS42L42 out of Reset */
-	gpio_data = snd_hda_codec_read(codec, CS8409_PIN_AFG, 0, AC_VERB_GET_GPIO_DATA, 0);
-	gpio_data |= cs42l42->reset_gpio;
-	snd_hda_codec_write(codec, CS8409_PIN_AFG, 0, AC_VERB_SET_GPIO_DATA, gpio_data);
+	spec->gpio_data = snd_hda_codec_read(codec, CS8409_PIN_AFG, 0, AC_VERB_GET_GPIO_DATA, 0);
+	spec->gpio_data |= cs42l42->reset_gpio;
+	snd_hda_codec_write(codec, CS8409_PIN_AFG, 0, AC_VERB_SET_GPIO_DATA, spec->gpio_data);
 	usleep_range(10000, 15000);
 
 	cs42l42->suspended = 0;
 
 	/* Initialize CS42L42 companion codec */
 	cs8409_i2c_bulk_write(cs42l42, cs42l42->init_seq, cs42l42->init_seq_num);
-	usleep_range(20000, 25000);
+	usleep_range(30000, 35000);
 
 	/* Clear interrupts, by reading interrupt status registers */
 	cs8409_i2c_bulk_read(cs42l42, irq_regs, ARRAY_SIZE(irq_regs));
 
-	if (cs42l42->full_scale_vol)
-		cs8409_i2c_write(cs42l42, 0x2001, 0x01);
+	fsv_old = cs8409_i2c_read(cs42l42, CS42L42_HP_CTL);
+	if (cs42l42->full_scale_vol == CS42L42_FULL_SCALE_VOL_0DB)
+		fsv_new = fsv_old & ~CS42L42_FULL_SCALE_VOL_MASK;
+	else
+		fsv_new = fsv_old & CS42L42_FULL_SCALE_VOL_MASK;
+	if (fsv_new != fsv_old)
+		cs8409_i2c_write(cs42l42, CS42L42_HP_CTL, fsv_new);
+
+	/* we have to explicitly allow unsol event handling even during the
+	 * resume phase so that the jack event is processed properly
+	 */
+	snd_hda_codec_allow_unsol_events(cs42l42->codec);
 
 	cs42l42_enable_jack_detect(cs42l42);
 }
@@ -757,40 +913,40 @@
 static void cs42l42_suspend(struct sub_codec *cs42l42)
 {
 	struct hda_codec *codec = cs42l42->codec;
-	unsigned int gpio_data;
+	struct cs8409_spec *spec = codec->spec;
 	int reg_cdc_status = 0;
 	const struct cs8409_i2c_param cs42l42_pwr_down_seq[] = {
-		{ 0x1F06, 0x02 },
-		{ 0x1129, 0x00 },
-		{ 0x2301, 0x3F },
-		{ 0x2302, 0x3F },
-		{ 0x2303, 0x3F },
-		{ 0x2001, 0x0F },
-		{ 0x2A01, 0x00 },
-		{ 0x1207, 0x00 },
-		{ 0x1101, 0xFE },
-		{ 0x1102, 0x8C },
-		{ 0x1101, 0xFF },
+		{ CS42L42_DAC_CTL2, 0x02 },
+		{ CS42L42_HS_CLAMP_DISABLE, 0x00 },
+		{ CS42L42_MIXER_CHA_VOL, 0x3F },
+		{ CS42L42_MIXER_ADC_VOL, 0x3F },
+		{ CS42L42_MIXER_CHB_VOL, 0x3F },
+		{ CS42L42_HP_CTL, 0x0F },
+		{ CS42L42_ASP_RX_DAI0_EN, 0x00 },
+		{ CS42L42_ASP_CLK_CFG, 0x00 },
+		{ CS42L42_PWR_CTL1, 0xFE },
+		{ CS42L42_PWR_CTL2, 0x8C },
+		{ CS42L42_PWR_CTL1, 0xFF },
 	};
 
 	cs8409_i2c_bulk_write(cs42l42, cs42l42_pwr_down_seq, ARRAY_SIZE(cs42l42_pwr_down_seq));
 
 	if (read_poll_timeout(cs8409_i2c_read, reg_cdc_status,
 			(reg_cdc_status & 0x1), CS42L42_PDN_SLEEP_US, CS42L42_PDN_TIMEOUT_US,
-			true, cs42l42, 0x1308) < 0)
+			true, cs42l42, CS42L42_CODEC_STATUS) < 0)
 		codec_warn(codec, "Timeout waiting for PDN_DONE for CS42L42\n");
 
 	/* Power down CS42L42 ASP/EQ/MIX/HP */
-	cs8409_i2c_write(cs42l42, 0x1102, 0x9C);
+	cs8409_i2c_write(cs42l42, CS42L42_PWR_CTL2, 0x9C);
 	cs42l42->suspended = 1;
 	cs42l42->last_page = 0;
 	cs42l42->hp_jack_in = 0;
 	cs42l42->mic_jack_in = 0;
 
 	/* Put CS42L42 into Reset */
-	gpio_data = snd_hda_codec_read(codec, CS8409_PIN_AFG, 0, AC_VERB_GET_GPIO_DATA, 0);
-	gpio_data &= ~cs42l42->reset_gpio;
-	snd_hda_codec_write(codec, CS8409_PIN_AFG, 0, AC_VERB_SET_GPIO_DATA, gpio_data);
+	spec->gpio_data = snd_hda_codec_read(codec, CS8409_PIN_AFG, 0, AC_VERB_GET_GPIO_DATA, 0);
+	spec->gpio_data &= ~cs42l42->reset_gpio;
+	snd_hda_codec_write(codec, CS8409_PIN_AFG, 0, AC_VERB_SET_GPIO_DATA, spec->gpio_data);
 }
 #endif
 
@@ -898,9 +1054,19 @@
 			cs8409_vendor_coef_set(codec, seq_bullseye->cir, seq_bullseye->coeff);
 	}
 
-	/* DMIC1_MO=00b, DMIC1/2_SR=1 */
-	if (codec->fixup_id == CS8409_WARLOCK || codec->fixup_id == CS8409_CYBORG)
-		cs8409_vendor_coef_set(codec, 0x09, 0x0003);
+	switch (codec->fixup_id) {
+	case CS8409_CYBORG:
+	case CS8409_WARLOCK_MLK_DUAL_MIC:
+		/* DMIC1_MO=00b, DMIC1/2_SR=1 */
+		cs8409_vendor_coef_set(codec, CS8409_DMIC_CFG, 0x0003);
+		break;
+	case CS8409_ODIN:
+		/* ASP1/2_xxx_EN=1, ASP1/2_MCLK_EN=0, DMIC1_SCL_EN=0 */
+		cs8409_vendor_coef_set(codec, CS8409_PAD_CFG_SLW_RATE_CTRL, 0xfc00);
+		break;
+	default:
+		break;
+	}
 
 	cs42l42_resume(cs42l42);
 
@@ -974,6 +1140,8 @@
 		spec->gen.no_primary_hp = 1;
 		spec->gen.suppress_vmaster = 1;
 
+		spec->speaker_pdn_gpio = 0;
+
 		/* GPIO 5 out, 3,4 in */
 		spec->gpio_dir = spec->scodecs[CS8409_CODEC0]->reset_gpio;
 		spec->gpio_data = 0;
@@ -985,28 +1153,33 @@
 		cs8409_fix_caps(codec, CS8409_CS42L42_HP_PIN_NID);
 		cs8409_fix_caps(codec, CS8409_CS42L42_AMIC_PIN_NID);
 
-		/* Set TIP_SENSE_EN for analog front-end of tip sense.
-		 * Additionally set HSBIAS_SENSE_EN and Full Scale volume for some variants.
-		 */
+		spec->scodecs[CS8409_CODEC0]->hsbias_hiz = 0x0020;
+
 		switch (codec->fixup_id) {
-		case CS8409_WARLOCK:
-			spec->scodecs[CS8409_CODEC0]->hsbias_hiz = 0x0020;
-			spec->scodecs[CS8409_CODEC0]->full_scale_vol = 1;
+		case CS8409_CYBORG:
+			spec->scodecs[CS8409_CODEC0]->full_scale_vol =
+				CS42L42_FULL_SCALE_VOL_MINUS6DB;
+			spec->speaker_pdn_gpio = CS8409_CYBORG_SPEAKER_PDN;
 			break;
-		case CS8409_BULLSEYE:
-			spec->scodecs[CS8409_CODEC0]->hsbias_hiz = 0x0020;
-			spec->scodecs[CS8409_CODEC0]->full_scale_vol = 0;
+		case CS8409_ODIN:
+			spec->scodecs[CS8409_CODEC0]->full_scale_vol = CS42L42_FULL_SCALE_VOL_0DB;
+			spec->speaker_pdn_gpio = CS8409_CYBORG_SPEAKER_PDN;
 			break;
-		case CS8409_CYBORG:
-			spec->scodecs[CS8409_CODEC0]->hsbias_hiz = 0x00a0;
-			spec->scodecs[CS8409_CODEC0]->full_scale_vol = 1;
+		case CS8409_WARLOCK_MLK:
+		case CS8409_WARLOCK_MLK_DUAL_MIC:
+			spec->scodecs[CS8409_CODEC0]->full_scale_vol = CS42L42_FULL_SCALE_VOL_0DB;
 			break;
 		default:
-			spec->scodecs[CS8409_CODEC0]->hsbias_hiz = 0x0003;
-			spec->scodecs[CS8409_CODEC0]->full_scale_vol = 1;
+			spec->scodecs[CS8409_CODEC0]->full_scale_vol =
+				CS42L42_FULL_SCALE_VOL_MINUS6DB;
 			break;
 		}
 
+		if (spec->speaker_pdn_gpio > 0) {
+			spec->gpio_dir |= spec->speaker_pdn_gpio;
+			spec->gpio_data |= spec->speaker_pdn_gpio;
+		}
+
 		break;
 	case HDA_FIXUP_ACT_PROBE:
 		/* Fix Sample Rate to 48kHz */
@@ -1015,13 +1188,17 @@
 		/* add hooks */
 		spec->gen.pcm_playback_hook = cs42l42_playback_pcm_hook;
 		spec->gen.pcm_capture_hook = cs42l42_capture_pcm_hook;
-		/* Set initial DMIC volume to -26 dB */
-		snd_hda_codec_amp_init_stereo(codec, CS8409_CS42L42_DMIC_ADC_PIN_NID,
-					      HDA_INPUT, 0, 0xff, 0x19);
+		if (codec->fixup_id != CS8409_ODIN)
+			/* Set initial DMIC volume to -26 dB */
+			snd_hda_codec_amp_init_stereo(codec, CS8409_CS42L42_DMIC_ADC_PIN_NID,
+						      HDA_INPUT, 0, 0xff, 0x19);
 		snd_hda_gen_add_kctl(&spec->gen, "Headphone Playback Volume",
 				&cs42l42_dac_volume_mixer);
 		snd_hda_gen_add_kctl(&spec->gen, "Mic Capture Volume",
 				&cs42l42_adc_volume_mixer);
+		if (spec->speaker_pdn_gpio > 0)
+			snd_hda_gen_add_kctl(&spec->gen, "Speaker Playback Switch",
+					     &cs8409_spk_sw_ctrl);
 		/* Disable Unsolicited Response during boot */
 		cs8409_enable_ur(codec, 0);
 		snd_hda_codec_set_name(codec, "CS8409/CS42L42");
@@ -1192,6 +1369,7 @@
 		spec->scodecs[CS8409_CODEC1] = &dolphin_cs42l42_1;
 		spec->scodecs[CS8409_CODEC1]->codec = codec;
 		spec->num_scodecs = 2;
+		spec->gen.suppress_vmaster = 1;
 
 		codec->patch_ops = cs8409_dolphin_patch_ops;
 
@@ -1214,6 +1392,9 @@
 		cs8409_fix_caps(codec, DOLPHIN_LO_PIN_NID);
 		cs8409_fix_caps(codec, DOLPHIN_AMIC_PIN_NID);
 
+		spec->scodecs[CS8409_CODEC0]->full_scale_vol = CS42L42_FULL_SCALE_VOL_MINUS6DB;
+		spec->scodecs[CS8409_CODEC1]->full_scale_vol = CS42L42_FULL_SCALE_VOL_MINUS6DB;
+
 		break;
 	case HDA_FIXUP_ACT_PROBE:
 		/* Fix Sample Rate to 48kHz */
@@ -1228,8 +1409,9 @@
 		kctrl = snd_hda_gen_add_kctl(&spec->gen, "Line Out Playback Volume",
 					     &cs42l42_dac_volume_mixer);
 		/* Update Line Out kcontrol template */
-		kctrl->private_value = HDA_COMPOSE_AMP_VAL_OFS(DOLPHIN_HP_PIN_NID, 3, CS8409_CODEC1,
-				       HDA_OUTPUT, CS42L42_VOL_DAC) | HDA_AMP_VAL_MIN_MUTE;
+		if (kctrl)
+			kctrl->private_value = HDA_COMPOSE_AMP_VAL_OFS(DOLPHIN_HP_PIN_NID, 3, CS8409_CODEC1,
+					       HDA_OUTPUT, CS42L42_VOL_DAC) | HDA_AMP_VAL_MIN_MUTE;
 		cs8409_enable_ur(codec, 0);
 		snd_hda_codec_set_name(codec, "CS8409/CS42L42");
 		break;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_cs8409.h
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_cs8409.h
@@ -12,6 +12,7 @@
 #include <linux/pci.h>
 #include <sound/tlv.h>
 #include <linux/workqueue.h>
+#include <sound/cs42l42.h>
 #include <sound/hda_codec.h>
 #include "hda_local.h"
 #include "hda_auto_parser.h"
@@ -222,25 +223,22 @@
 #define CS42L42_HP_VOL_REAL_MAX			(0)
 #define CS42L42_AMIC_VOL_REAL_MIN		(-97)
 #define CS42L42_AMIC_VOL_REAL_MAX		(12)
-#define CS42L42_REG_HS_VOL_CHA			(0x2301)
-#define CS42L42_REG_HS_VOL_CHB			(0x2303)
-#define CS42L42_REG_HS_VOL_MASK			(0x003F)
-#define CS42L42_REG_AMIC_VOL			(0x1D03)
 #define CS42L42_REG_AMIC_VOL_MASK		(0x00FF)
-#define CS42L42_HSDET_AUTO_DONE			(0x02)
 #define CS42L42_HSTYPE_MASK			(0x03)
-#define CS42L42_JACK_INSERTED			(0x0C)
-#define CS42L42_JACK_REMOVED			(0x00)
 #define CS42L42_I2C_TIMEOUT_US			(20000)
 #define CS42L42_I2C_SLEEP_US			(2000)
 #define CS42L42_PDN_TIMEOUT_US			(250000)
 #define CS42L42_PDN_SLEEP_US			(2000)
+#define CS42L42_FULL_SCALE_VOL_MASK		(2)
+#define CS42L42_FULL_SCALE_VOL_0DB		(1)
+#define CS42L42_FULL_SCALE_VOL_MINUS6DB		(0)
 
 /* Dell BULLSEYE / WARLOCK / CYBORG Specific Definitions */
 
 #define CS42L42_I2C_ADDR			(0x48 << 1)
 #define CS8409_CS42L42_RESET			GENMASK(5, 5) /* CS8409_GPIO5 */
 #define CS8409_CS42L42_INT			GENMASK(4, 4) /* CS8409_GPIO4 */
+#define CS8409_CYBORG_SPEAKER_PDN		GENMASK(2, 2) /* CS8409_GPIO2 */
 #define CS8409_CS42L42_HP_PIN_NID		CS8409_PIN_ASP1_TRANSMITTER_A
 #define CS8409_CS42L42_SPK_PIN_NID		CS8409_PIN_ASP2_TRANSMITTER_A
 #define CS8409_CS42L42_AMIC_PIN_NID		CS8409_PIN_ASP1_RECEIVER_A
@@ -264,10 +262,13 @@
 enum {
 	CS8409_BULLSEYE,
 	CS8409_WARLOCK,
+	CS8409_WARLOCK_MLK,
+	CS8409_WARLOCK_MLK_DUAL_MIC,
 	CS8409_CYBORG,
 	CS8409_FIXUPS,
 	CS8409_DOLPHIN,
 	CS8409_DOLPHIN_FIXUPS,
+	CS8409_ODIN,
 };
 
 enum {
@@ -326,6 +327,8 @@
 	unsigned int gpio_dir;
 	unsigned int gpio_data;
 
+	int speaker_pdn_gpio;
+
 	struct mutex i2c_mux;
 	unsigned int i2c_clck_enabled;
 	unsigned int dev_addr;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_hdmi.c
@@ -162,6 +162,8 @@
 	bool dyn_pin_out;
 	bool dyn_pcm_assign;
 	bool dyn_pcm_no_legacy;
+	bool nv_dp_workaround; /* workaround DP audio infoframe for Nvidia */
+
 	bool intel_hsw_fixup;	/* apply Intel platform-specific fixups */
 	/*
 	 * Non-generic VIA/NVIDIA specific
@@ -671,15 +673,24 @@
 				     int ca, int active_channels,
 				     int conn_type)
 {
+	struct hdmi_spec *spec = codec->spec;
 	union audio_infoframe ai;
 
 	memset(&ai, 0, sizeof(ai));
-	if (conn_type == 0) { /* HDMI */
+	if ((conn_type == 0) || /* HDMI */
+		/* Nvidia DisplayPort: Nvidia HW expects same layout as HDMI */
+		(conn_type == 1 && spec->nv_dp_workaround)) {
 		struct hdmi_audio_infoframe *hdmi_ai = &ai.hdmi;
 
-		hdmi_ai->type		= 0x84;
-		hdmi_ai->ver		= 0x01;
-		hdmi_ai->len		= 0x0a;
+		if (conn_type == 0) { /* HDMI */
+			hdmi_ai->type		= 0x84;
+			hdmi_ai->ver		= 0x01;
+			hdmi_ai->len		= 0x0a;
+		} else {/* Nvidia DP */
+			hdmi_ai->type		= 0x84;
+			hdmi_ai->ver		= 0x1b;
+			hdmi_ai->len		= 0x11 << 2;
+		}
 		hdmi_ai->CC02_CT47	= active_channels - 1;
 		hdmi_ai->CA		= ca;
 		hdmi_checksum_audio_infoframe(hdmi_ai);
@@ -1259,6 +1270,7 @@
 	set_bit(pcm_idx, &spec->pcm_in_use);
 	per_pin = get_pin(spec, pin_idx);
 	per_pin->cvt_nid = per_cvt->cvt_nid;
+	per_pin->silent_stream = false;
 	hinfo->nid = per_cvt->cvt_nid;
 
 	/* flip stripe flag for the assigned stream if supported */
@@ -1387,7 +1399,7 @@
 
  last_try:
 	/* the last try; check the empty slots in pins */
-	for (i = 0; i < spec->num_nids; i++) {
+	for (i = 0; i < spec->pcm_used; i++) {
 		if (!test_bit(i, &spec->pcm_bitmap))
 			return i;
 	}
@@ -1535,7 +1547,7 @@
 		}
 	}
 
-	if (!eld->eld_valid || eld->eld_size <= 0) {
+	if (!eld->eld_valid || eld->eld_size <= 0 || eld->info.sad_count <= 0) {
 		eld->eld_valid = false;
 		eld->eld_size = 0;
 	}
@@ -1617,6 +1629,7 @@
 	struct hda_codec *codec = per_pin->codec;
 	struct hdmi_spec *spec = codec->spec;
 	struct hdmi_eld *eld = &spec->temp_eld;
+	struct device *dev = hda_codec_dev(codec);
 	hda_nid_t pin_nid = per_pin->pin_nid;
 	int dev_id = per_pin->dev_id;
 	/*
@@ -1630,8 +1643,13 @@
 	int present;
 	int ret;
 
+#ifdef	CONFIG_PM
+	if (dev->power.runtime_status == RPM_SUSPENDING)
+		return;
+#endif
+
 	ret = snd_hda_power_up_pm(codec);
-	if (ret < 0 && pm_runtime_suspended(hda_codec_dev(codec)))
+	if (ret < 0 && pm_runtime_suspended(dev))
 		goto out;
 
 	present = snd_hda_jack_pin_sense(codec, pin_nid, dev_id);
@@ -1942,9 +1960,16 @@
 }
 
 static const struct snd_pci_quirk force_connect_list[] = {
+	SND_PCI_QUIRK(0x103c, 0x83e2, "HP EliteDesk 800 G4", 1),
+	SND_PCI_QUIRK(0x103c, 0x83ef, "HP MP9 G4 Retail System AMS", 1),
 	SND_PCI_QUIRK(0x103c, 0x870f, "HP", 1),
 	SND_PCI_QUIRK(0x103c, 0x871a, "HP", 1),
+	SND_PCI_QUIRK(0x103c, 0x8711, "HP", 1),
+	SND_PCI_QUIRK(0x103c, 0x8715, "HP", 1),
+	SND_PCI_QUIRK(0x1043, 0x86ae, "ASUS", 1),  /* Z170 PRO */
+	SND_PCI_QUIRK(0x1043, 0x86c7, "ASUS", 1),  /* Z170M PLUS */
 	SND_PCI_QUIRK(0x1462, 0xec94, "MS-7C94", 1),
+	SND_PCI_QUIRK(0x8086, 0x2060, "Intel NUC5CPYB", 1),
 	SND_PCI_QUIRK(0x8086, 0x2081, "Intel NUC 10", 1),
 	{}
 };
@@ -2257,7 +2282,9 @@
 	 * dev_num is the device entry number in a pin
 	 */
 
-	if (codec->mst_no_extra_pcms)
+	if (spec->dyn_pcm_no_legacy && codec->mst_no_extra_pcms)
+		pcm_num = spec->num_cvts;
+	else if (codec->mst_no_extra_pcms)
 		pcm_num = spec->num_nids;
 	else
 		pcm_num = spec->num_nids + spec->dev_num - 1;
@@ -2665,9 +2692,6 @@
 	 */
 	if (codec->core.dev.power.power_state.event == PM_EVENT_SUSPEND)
 		return;
-	/* ditto during suspend/resume process itself */
-	if (snd_hdac_is_in_pm(&codec->core))
-		return;
 
 	check_presence_and_report(codec, pin_nid, dev_id);
 }
@@ -2851,9 +2875,6 @@
 	 */
 	if (codec->core.dev.power.power_state.event == PM_EVENT_SUSPEND)
 		return;
-	/* ditto during suspend/resume process itself */
-	if (snd_hdac_is_in_pm(&codec->core))
-		return;
 
 	snd_hdac_i915_set_bclk(&codec->bus->core);
 	check_presence_and_report(codec, pin_nid, dev_id);
@@ -2947,7 +2968,8 @@
 
 /* Intel Haswell and onwards; audio component with eld notifier */
 static int intel_hsw_common_init(struct hda_codec *codec, hda_nid_t vendor_nid,
-				 const int *port_map, int port_num, int dev_num)
+				 const int *port_map, int port_num, int dev_num,
+				 bool send_silent_stream)
 {
 	struct hdmi_spec *spec;
 	int err;
@@ -2980,7 +3002,7 @@
 	 * Enable silent stream feature, if it is enabled via
 	 * module param or Kconfig option
 	 */
-	if (enable_silent_stream)
+	if (send_silent_stream)
 		spec->send_silent_stream = true;
 
 	return parse_intel_hdmi(codec);
@@ -2988,12 +3010,18 @@
 
 static int patch_i915_hsw_hdmi(struct hda_codec *codec)
 {
-	return intel_hsw_common_init(codec, 0x08, NULL, 0, 3);
+	return intel_hsw_common_init(codec, 0x08, NULL, 0, 3,
+				     enable_silent_stream);
 }
 
 static int patch_i915_glk_hdmi(struct hda_codec *codec)
 {
-	return intel_hsw_common_init(codec, 0x0b, NULL, 0, 3);
+	/*
+	 * Silent stream calls audio component .get_power() from
+	 * .pin_eld_notify(). On GLK this will deadlock in i915 due
+	 * to the audio vs. CDCLK workaround.
+	 */
+	return intel_hsw_common_init(codec, 0x0b, NULL, 0, 3, false);
 }
 
 static int patch_i915_icl_hdmi(struct hda_codec *codec)
@@ -3004,7 +3032,8 @@
 	 */
 	static const int map[] = {0x0, 0x4, 0x6, 0x8, 0xa, 0xb};
 
-	return intel_hsw_common_init(codec, 0x02, map, ARRAY_SIZE(map), 3);
+	return intel_hsw_common_init(codec, 0x02, map, ARRAY_SIZE(map), 3,
+				     enable_silent_stream);
 }
 
 static int patch_i915_tgl_hdmi(struct hda_codec *codec)
@@ -3016,7 +3045,8 @@
 	static const int map[] = {0x4, 0x6, 0x8, 0xa, 0xb, 0xc, 0xd, 0xe, 0xf};
 	int ret;
 
-	ret = intel_hsw_common_init(codec, 0x02, map, ARRAY_SIZE(map), 4);
+	ret = intel_hsw_common_init(codec, 0x02, map, ARRAY_SIZE(map), 4,
+				    enable_silent_stream);
 	if (!ret) {
 		struct hdmi_spec *spec = codec->spec;
 
@@ -3522,6 +3552,7 @@
 	spec->pcm_playback.rates = SUPPORTED_RATES;
 	spec->pcm_playback.maxbps = SUPPORTED_MAXBPS;
 	spec->pcm_playback.formats = SUPPORTED_FORMATS;
+	spec->nv_dp_workaround = true;
 	return 0;
 }
 
@@ -3661,6 +3692,7 @@
 	spec->chmap.ops.chmap_cea_alloc_validate_get_type =
 		nvhdmi_chmap_cea_alloc_validate_get_type;
 	spec->chmap.ops.chmap_validate = nvhdmi_chmap_validate;
+	spec->nv_dp_workaround = true;
 
 	codec->link_down_at_suspend = 1;
 
@@ -3684,6 +3716,7 @@
 	spec->chmap.ops.chmap_cea_alloc_validate_get_type =
 		nvhdmi_chmap_cea_alloc_validate_get_type;
 	spec->chmap.ops.chmap_validate = nvhdmi_chmap_validate;
+	spec->nv_dp_workaround = true;
 
 	codec->link_down_at_suspend = 1;
 
@@ -3851,11 +3884,13 @@
 	if (err)
 		return err;
 
+	codec->depop_delay = 10;
 	codec->patch_ops.build_pcms = tegra_hdmi_build_pcms;
 	spec = codec->spec;
 	spec->chmap.ops.chmap_cea_alloc_validate_get_type =
 		nvhdmi_chmap_cea_alloc_validate_get_type;
 	spec->chmap.ops.chmap_validate = nvhdmi_chmap_validate;
+	spec->nv_dp_workaround = true;
 
 	return 0;
 }
@@ -4268,6 +4303,22 @@
 	return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID);
 }
 
+static int patch_gf_hdmi(struct hda_codec *codec)
+{
+	int err;
+
+	err = patch_generic_hdmi(codec);
+	if (err)
+		return err;
+
+	/*
+	 * Glenfly GPUs have two codecs, stream switches from one codec to
+	 * another, need to do actual clean-ups in codec_cleanup_stream
+	 */
+	codec->no_sticky_stream = 1;
+	return 0;
+}
+
 /*
  * patch entries
  */
@@ -4355,8 +4406,19 @@
 HDA_CODEC_ENTRY(0x10de009e, "GPU 9e HDMI/DP",	patch_nvhdmi),
 HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP",	patch_nvhdmi),
 HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP",	patch_nvhdmi),
+HDA_CODEC_ENTRY(0x10de00a3, "GPU a3 HDMI/DP",	patch_nvhdmi),
+HDA_CODEC_ENTRY(0x10de00a4, "GPU a4 HDMI/DP",	patch_nvhdmi),
+HDA_CODEC_ENTRY(0x10de00a5, "GPU a5 HDMI/DP",	patch_nvhdmi),
+HDA_CODEC_ENTRY(0x10de00a6, "GPU a6 HDMI/DP",	patch_nvhdmi),
+HDA_CODEC_ENTRY(0x10de00a7, "GPU a7 HDMI/DP",	patch_nvhdmi),
 HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI",	patch_nvhdmi_2ch),
 HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI",	patch_nvhdmi_2ch),
+HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP",	patch_gf_hdmi),
+HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP",	patch_gf_hdmi),
+HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP",	patch_gf_hdmi),
+HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP",	patch_gf_hdmi),
+HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP",	patch_gf_hdmi),
+HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP",	patch_gf_hdmi),
 HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP",	patch_via_hdmi),
 HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP",	patch_via_hdmi),
 HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP",	patch_generic_hdmi),
@@ -4380,10 +4442,12 @@
 HDA_CODEC_ENTRY(0x80862812, "Tigerlake HDMI",	patch_i915_tgl_hdmi),
 HDA_CODEC_ENTRY(0x80862814, "DG1 HDMI",	patch_i915_tgl_hdmi),
 HDA_CODEC_ENTRY(0x80862815, "Alderlake HDMI",	patch_i915_tgl_hdmi),
-HDA_CODEC_ENTRY(0x8086281c, "Alderlake-P HDMI", patch_i915_tgl_hdmi),
 HDA_CODEC_ENTRY(0x80862816, "Rocketlake HDMI",	patch_i915_tgl_hdmi),
+HDA_CODEC_ENTRY(0x80862818, "Raptorlake HDMI",	patch_i915_tgl_hdmi),
+HDA_CODEC_ENTRY(0x80862819, "DG2 HDMI",	patch_i915_tgl_hdmi),
 HDA_CODEC_ENTRY(0x8086281a, "Jasperlake HDMI",	patch_i915_icl_hdmi),
 HDA_CODEC_ENTRY(0x8086281b, "Elkhartlake HDMI",	patch_i915_icl_hdmi),
+HDA_CODEC_ENTRY(0x8086281c, "Alderlake-P HDMI", patch_i915_tgl_hdmi),
 HDA_CODEC_ENTRY(0x80862880, "CedarTrail HDMI",	patch_generic_hdmi),
 HDA_CODEC_ENTRY(0x80862882, "Valleyview2 HDMI",	patch_i915_byt_hdmi),
 HDA_CODEC_ENTRY(0x80862883, "Braswell HDMI",	patch_i915_byt_hdmi),
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_realtek.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_realtek.c
@@ -25,6 +25,7 @@
 #include "hda_auto_parser.h"
 #include "hda_jack.h"
 #include "hda_generic.h"
+#include "hda_component.h"
 
 /* keep halting ALC5505 DSP, for power saving */
 #define HALT_REALTEK_ALC5505
@@ -97,6 +98,7 @@
 	unsigned int gpio_mic_led_mask;
 	struct alc_coef_led mute_led_coef;
 	struct alc_coef_led mic_led_coef;
+	struct mutex coef_mutex;
 
 	hda_nid_t headset_mic_pin;
 	hda_nid_t headphone_mic_pin;
@@ -119,6 +121,7 @@
 	unsigned int ultra_low_power:1;
 	unsigned int has_hs_key:1;
 	unsigned int no_internal_mic_pin:1;
+	unsigned int en_3kpull_low:1;
 
 	/* for PLL fix */
 	hda_nid_t pll_nid;
@@ -126,14 +129,34 @@
 	unsigned int coef0;
 	struct input_dev *kb_dev;
 	u8 alc_mute_keycode_map[1];
+
+	/* component binding */
+	struct component_match *match;
+	struct hda_component comps[HDA_MAX_COMPONENTS];
 };
 
 /*
  * COEF access helper functions
  */
 
-static int alc_read_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
-			       unsigned int coef_idx)
+static void coef_mutex_lock(struct hda_codec *codec)
+{
+	struct alc_spec *spec = codec->spec;
+
+	snd_hda_power_up_pm(codec);
+	mutex_lock(&spec->coef_mutex);
+}
+
+static void coef_mutex_unlock(struct hda_codec *codec)
+{
+	struct alc_spec *spec = codec->spec;
+
+	mutex_unlock(&spec->coef_mutex);
+	snd_hda_power_down_pm(codec);
+}
+
+static int __alc_read_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
+				 unsigned int coef_idx)
 {
 	unsigned int val;
 
@@ -142,28 +165,56 @@
 	return val;
 }
 
+static int alc_read_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
+			       unsigned int coef_idx)
+{
+	unsigned int val;
+
+	coef_mutex_lock(codec);
+	val = __alc_read_coefex_idx(codec, nid, coef_idx);
+	coef_mutex_unlock(codec);
+	return val;
+}
+
 #define alc_read_coef_idx(codec, coef_idx) \
 	alc_read_coefex_idx(codec, 0x20, coef_idx)
 
-static void alc_write_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
-				 unsigned int coef_idx, unsigned int coef_val)
+static void __alc_write_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
+				   unsigned int coef_idx, unsigned int coef_val)
 {
 	snd_hda_codec_write(codec, nid, 0, AC_VERB_SET_COEF_INDEX, coef_idx);
 	snd_hda_codec_write(codec, nid, 0, AC_VERB_SET_PROC_COEF, coef_val);
 }
 
+static void alc_write_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
+				 unsigned int coef_idx, unsigned int coef_val)
+{
+	coef_mutex_lock(codec);
+	__alc_write_coefex_idx(codec, nid, coef_idx, coef_val);
+	coef_mutex_unlock(codec);
+}
+
 #define alc_write_coef_idx(codec, coef_idx, coef_val) \
 	alc_write_coefex_idx(codec, 0x20, coef_idx, coef_val)
 
+static void __alc_update_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
+				    unsigned int coef_idx, unsigned int mask,
+				    unsigned int bits_set)
+{
+	unsigned int val = __alc_read_coefex_idx(codec, nid, coef_idx);
+
+	if (val != -1)
+		__alc_write_coefex_idx(codec, nid, coef_idx,
+				       (val & ~mask) | bits_set);
+}
+
 static void alc_update_coefex_idx(struct hda_codec *codec, hda_nid_t nid,
 				  unsigned int coef_idx, unsigned int mask,
 				  unsigned int bits_set)
 {
-	unsigned int val = alc_read_coefex_idx(codec, nid, coef_idx);
-
-	if (val != -1)
-		alc_write_coefex_idx(codec, nid, coef_idx,
-				     (val & ~mask) | bits_set);
+	coef_mutex_lock(codec);
+	__alc_update_coefex_idx(codec, nid, coef_idx, mask, bits_set);
+	coef_mutex_unlock(codec);
 }
 
 #define alc_update_coef_idx(codec, coef_idx, mask, bits_set)	\
@@ -196,13 +247,15 @@
 static void alc_process_coef_fw(struct hda_codec *codec,
 				const struct coef_fw *fw)
 {
+	coef_mutex_lock(codec);
 	for (; fw->nid; fw++) {
 		if (fw->mask == (unsigned short)-1)
-			alc_write_coefex_idx(codec, fw->nid, fw->idx, fw->val);
+			__alc_write_coefex_idx(codec, fw->nid, fw->idx, fw->val);
 		else
-			alc_update_coefex_idx(codec, fw->nid, fw->idx,
-					      fw->mask, fw->val);
+			__alc_update_coefex_idx(codec, fw->nid, fw->idx,
+						fw->mask, fw->val);
 	}
+	coef_mutex_unlock(codec);
 }
 
 /*
@@ -391,6 +444,7 @@
 	case 0x10ec0245:
 	case 0x10ec0255:
 	case 0x10ec0256:
+	case 0x19e58326:
 	case 0x10ec0257:
 	case 0x10ec0282:
 	case 0x10ec0283:
@@ -414,6 +468,8 @@
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
+		alc_write_coef_idx(codec, 0x6e, 0x0c25);
+		fallthrough;
 	case 0x10ec0294:
 	case 0x10ec0700:
 	case 0x10ec0701:
@@ -525,18 +581,25 @@
 {
 	struct alc_spec *spec = codec->spec;
 
+	if (spec->no_shutup_pins)
+		return;
+
 	switch (codec->core.vendor_id) {
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x10ec0257:
+	case 0x19e58326:
 	case 0x10ec0283:
+	case 0x10ec0285:
 	case 0x10ec0286:
+	case 0x10ec0287:
 	case 0x10ec0288:
+	case 0x10ec0295:
 	case 0x10ec0298:
 		alc_headset_mic_no_shutup(codec);
 		break;
 	default:
-		if (!spec->no_shutup_pins)
-			snd_hda_shutup_pins(codec);
+		snd_hda_shutup_pins(codec);
 		break;
 	}
 }
@@ -777,7 +840,7 @@
 			alc_setup_gpio(codec, 0x02);
 			break;
 		case 7:
-			alc_setup_gpio(codec, 0x03);
+			alc_setup_gpio(codec, 0x04);
 			break;
 		case 5:
 		default:
@@ -885,6 +948,9 @@
 	return 0;
 }
 
+#define alc_free	snd_hda_gen_free
+
+#ifdef CONFIG_PM
 static inline void alc_shutup(struct hda_codec *codec)
 {
 	struct alc_spec *spec = codec->spec;
@@ -898,9 +964,6 @@
 		alc_shutup_pins(codec);
 }
 
-#define alc_free	snd_hda_gen_free
-
-#ifdef CONFIG_PM
 static void alc_power_eapd(struct hda_codec *codec)
 {
 	alc_auto_setup_eapd(codec, false);
@@ -914,9 +977,7 @@
 		spec->power_hook(codec);
 	return 0;
 }
-#endif
 
-#ifdef CONFIG_PM
 static int alc_resume(struct hda_codec *codec)
 {
 	struct alc_spec *spec = codec->spec;
@@ -1148,6 +1209,7 @@
 	codec->spdif_status_reset = 1;
 	codec->forced_resume = 1;
 	codec->patch_ops = alc_patch_ops;
+	mutex_init(&spec->coef_mutex);
 
 	err = alc_codec_rename_from_preset(codec);
 	if (err < 0) {
@@ -1924,11 +1986,14 @@
 	ALC887_FIXUP_ASUS_BASS,
 	ALC887_FIXUP_BASS_CHMAP,
 	ALC1220_FIXUP_GB_DUAL_CODECS,
+	ALC1220_FIXUP_GB_X570,
 	ALC1220_FIXUP_CLEVO_P950,
 	ALC1220_FIXUP_CLEVO_PB51ED,
 	ALC1220_FIXUP_CLEVO_PB51ED_PINS,
 	ALC887_FIXUP_ASUS_AUDIO,
 	ALC887_FIXUP_ASUS_HMIC,
+	ALCS1200A_FIXUP_MIC_VREF,
+	ALC888VD_FIXUP_MIC_100VREF,
 };
 
 static void alc889_fixup_coef(struct hda_codec *codec,
@@ -2113,6 +2178,30 @@
 	}
 }
 
+static void alc1220_fixup_gb_x570(struct hda_codec *codec,
+				     const struct hda_fixup *fix,
+				     int action)
+{
+	static const hda_nid_t conn1[] = { 0x0c };
+	static const struct coef_fw gb_x570_coefs[] = {
+		WRITE_COEF(0x07, 0x03c0),
+		WRITE_COEF(0x1a, 0x01c1),
+		WRITE_COEF(0x1b, 0x0202),
+		WRITE_COEF(0x43, 0x3005),
+		{}
+	};
+
+	switch (action) {
+	case HDA_FIXUP_ACT_PRE_PROBE:
+		snd_hda_override_conn_list(codec, 0x14, ARRAY_SIZE(conn1), conn1);
+		snd_hda_override_conn_list(codec, 0x1b, ARRAY_SIZE(conn1), conn1);
+		break;
+	case HDA_FIXUP_ACT_INIT:
+		alc_process_coef_fw(codec, gb_x570_coefs);
+		break;
+	}
+}
+
 static void alc1220_fixup_clevo_p950(struct hda_codec *codec,
 				     const struct hda_fixup *fix,
 				     int action)
@@ -2415,6 +2504,10 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc1220_fixup_gb_dual_codecs,
 	},
+	[ALC1220_FIXUP_GB_X570] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc1220_fixup_gb_x570,
+	},
 	[ALC1220_FIXUP_CLEVO_P950] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc1220_fixup_clevo_p950,
@@ -2446,6 +2539,21 @@
 		.chained = true,
 		.chain_id = ALC887_FIXUP_ASUS_AUDIO,
 	},
+	[ALCS1200A_FIXUP_MIC_VREF] = {
+		.type = HDA_FIXUP_PINCTLS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x18, PIN_VREF50 }, /* rear mic */
+			{ 0x19, PIN_VREF50 }, /* front mic */
+			{}
+		}
+	},
+	[ALC888VD_FIXUP_MIC_100VREF] = {
+		.type = HDA_FIXUP_PINCTLS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x18, PIN_VREF100 }, /* headset mic */
+			{}
+		}
+	},
 };
 
 static const struct snd_pci_quirk alc882_fixup_tbl[] = {
@@ -2483,6 +2591,7 @@
 	SND_PCI_QUIRK(0x1043, 0x835f, "Asus Eee 1601", ALC888_FIXUP_EEE1601),
 	SND_PCI_QUIRK(0x1043, 0x84bc, "ASUS ET2700", ALC887_FIXUP_ASUS_BASS),
 	SND_PCI_QUIRK(0x1043, 0x8691, "ASUS ROG Ranger VIII", ALC882_FIXUP_GPIO3),
+	SND_PCI_QUIRK(0x1043, 0x8797, "ASUS TUF B550M-PLUS", ALCS1200A_FIXUP_MIC_VREF),
 	SND_PCI_QUIRK(0x104d, 0x9043, "Sony Vaio VGC-LN51JGB", ALC882_FIXUP_NO_PRIMARY_HP),
 	SND_PCI_QUIRK(0x104d, 0x9044, "Sony VAIO AiO", ALC882_FIXUP_NO_PRIMARY_HP),
 	SND_PCI_QUIRK(0x104d, 0x9047, "Sony Vaio TT", ALC889_FIXUP_VAIO_TT),
@@ -2514,11 +2623,13 @@
 	SND_PCI_QUIRK(0x106b, 0x4a00, "Macbook 5,2", ALC889_FIXUP_MBA11_VREF),
 
 	SND_PCI_QUIRK(0x1071, 0x8258, "Evesham Voyaeger", ALC882_FIXUP_EAPD),
+	SND_PCI_QUIRK(0x10ec, 0x12d8, "iBase Elo Touch", ALC888VD_FIXUP_MIC_100VREF),
 	SND_PCI_QUIRK(0x13fe, 0x1009, "Advantech MIT-W101", ALC886_FIXUP_EAPD),
 	SND_PCI_QUIRK(0x1458, 0xa002, "Gigabyte EP45-DS3/Z87X-UD3H", ALC889_FIXUP_FRONT_HP_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1458, 0xa0b8, "Gigabyte AZ370-Gaming", ALC1220_FIXUP_GB_DUAL_CODECS),
-	SND_PCI_QUIRK(0x1458, 0xa0cd, "Gigabyte X570 Aorus Master", ALC1220_FIXUP_CLEVO_P950),
-	SND_PCI_QUIRK(0x1458, 0xa0ce, "Gigabyte X570 Aorus Xtreme", ALC1220_FIXUP_CLEVO_P950),
+	SND_PCI_QUIRK(0x1458, 0xa0cd, "Gigabyte X570 Aorus Master", ALC1220_FIXUP_GB_X570),
+	SND_PCI_QUIRK(0x1458, 0xa0ce, "Gigabyte X570 Aorus Xtreme", ALC1220_FIXUP_GB_X570),
+	SND_PCI_QUIRK(0x1458, 0xa0d5, "Gigabyte X570S Aorus Master", ALC1220_FIXUP_GB_X570),
 	SND_PCI_QUIRK(0x1462, 0x11f7, "MSI-GE63", ALC1220_FIXUP_CLEVO_P950),
 	SND_PCI_QUIRK(0x1462, 0x1228, "MSI-GP63", ALC1220_FIXUP_CLEVO_P950),
 	SND_PCI_QUIRK(0x1462, 0x1229, "MSI-GP73", ALC1220_FIXUP_CLEVO_P950),
@@ -2530,15 +2641,20 @@
 	SND_PCI_QUIRK(0x1462, 0xda57, "MSI Z270-Gaming", ALC1220_FIXUP_GB_DUAL_CODECS),
 	SND_PCI_QUIRK_VENDOR(0x1462, "MSI", ALC882_FIXUP_GPIO3),
 	SND_PCI_QUIRK(0x147b, 0x107a, "Abit AW9D-MAX", ALC882_FIXUP_ABIT_AW9D_MAX),
+	SND_PCI_QUIRK(0x1558, 0x3702, "Clevo X370SN[VW]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x50d3, "Clevo PC50[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x65d1, "Clevo PB51[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x65d2, "Clevo PB51R[CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x65e1, "Clevo PB51[ED][DF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x65e5, "Clevo PC50D[PRS](?:-D|-G)?", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x65f1, "Clevo PC50HS", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
+	SND_PCI_QUIRK(0x1558, 0x65f5, "Clevo PD50PN[NRT]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
+	SND_PCI_QUIRK(0x1558, 0x66a2, "Clevo PE60RNE", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x67d1, "Clevo PB71[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x67e1, "Clevo PB71[DE][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x67e5, "Clevo PC70D[PRS](?:-D|-G)?", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
+	SND_PCI_QUIRK(0x1558, 0x67f1, "Clevo PC70H[PRS]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
+	SND_PCI_QUIRK(0x1558, 0x67f5, "Clevo PD70PN[NRT]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x70d1, "Clevo PC70[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x7714, "Clevo X170SM", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x7715, "Clevo X170KM-G", ALC1220_FIXUP_CLEVO_PB51ED),
@@ -2554,6 +2670,7 @@
 	SND_PCI_QUIRK(0x1558, 0x96e1, "Clevo P960[ER][CDFN]-K", ALC1220_FIXUP_CLEVO_P950),
 	SND_PCI_QUIRK(0x1558, 0x97e1, "Clevo P970[ER][CDFN]", ALC1220_FIXUP_CLEVO_P950),
 	SND_PCI_QUIRK(0x1558, 0x97e2, "Clevo P970RC-M", ALC1220_FIXUP_CLEVO_P950),
+	SND_PCI_QUIRK(0x1558, 0xd502, "Clevo PD50SNE", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK_VENDOR(0x1558, "Clevo laptop", ALC882_FIXUP_EAPD),
 	SND_PCI_QUIRK(0x161f, 0x2054, "Medion laptop", ALC883_FIXUP_EAPD),
 	SND_PCI_QUIRK(0x17aa, 0x3a0d, "Lenovo Y530", ALC882_FIXUP_LENOVO_Y530),
@@ -2592,6 +2709,7 @@
 	{.id = ALC882_FIXUP_NO_PRIMARY_HP, .name = "no-primary-hp"},
 	{.id = ALC887_FIXUP_ASUS_BASS, .name = "asus-bass"},
 	{.id = ALC1220_FIXUP_GB_DUAL_CODECS, .name = "dual-codecs"},
+	{.id = ALC1220_FIXUP_GB_X570, .name = "gb-x570"},
 	{.id = ALC1220_FIXUP_CLEVO_P950, .name = "clevo-p950"},
 	{}
 };
@@ -3047,6 +3165,7 @@
 	ALC269_TYPE_ALC257,
 	ALC269_TYPE_ALC215,
 	ALC269_TYPE_ALC225,
+	ALC269_TYPE_ALC245,
 	ALC269_TYPE_ALC287,
 	ALC269_TYPE_ALC294,
 	ALC269_TYPE_ALC300,
@@ -3084,6 +3203,7 @@
 	case ALC269_TYPE_ALC257:
 	case ALC269_TYPE_ALC215:
 	case ALC269_TYPE_ALC225:
+	case ALC269_TYPE_ALC245:
 	case ALC269_TYPE_ALC287:
 	case ALC269_TYPE_ALC294:
 	case ALC269_TYPE_ALC300:
@@ -3151,6 +3271,8 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x10ec0257:
+	case 0x19e58326:
 		alc_write_coef_idx(codec, 0x48, 0x0);
 		alc_update_coef_idx(codec, 0x49, 0x0045, 0x0);
 		break;
@@ -3179,6 +3301,8 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x10ec0257:
+	case 0x19e58326:
 		alc_write_coef_idx(codec, 0x48, 0xd011);
 		alc_update_coef_idx(codec, 0x49, 0x007f, 0x0045);
 		break;
@@ -3462,17 +3586,6 @@
 	hda_nid_t hp_pin = alc_get_hp_pin(spec);
 	bool hp_pin_sense;
 
-	if (!hp_pin)
-		hp_pin = 0x21;
-
-	msleep(30);
-
-	hp_pin_sense = snd_hda_jack_detect(codec, hp_pin);
-
-	if (hp_pin_sense)
-		msleep(2);
-
-	alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x1); /* Low power */
 	if (spec->ultra_low_power) {
 		alc_update_coef_idx(codec, 0x03, 1<<1, 1<<1);
 		alc_update_coef_idx(codec, 0x08, 3<<2, 3<<2);
@@ -3482,20 +3595,29 @@
 		msleep(30);
 	}
 
-	snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
+	if (!hp_pin)
+		hp_pin = 0x21;
 
-	if (hp_pin_sense || spec->ultra_low_power)
-		msleep(85);
+	msleep(30);
 
-	snd_hda_codec_write(codec, hp_pin, 0,
+	hp_pin_sense = snd_hda_jack_detect(codec, hp_pin);
+
+	if (hp_pin_sense) {
+		msleep(2);
+		alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x1); /* Low power */
+
+		snd_hda_codec_write(codec, hp_pin, 0,
 			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
 
-	if (hp_pin_sense || spec->ultra_low_power)
-		msleep(100);
+		msleep(75);
 
+		snd_hda_codec_write(codec, hp_pin, 0,
+			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+
+		msleep(75);
+		alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x4); /* Hight power */
+	}
 	alc_update_coef_idx(codec, 0x46, 3 << 12, 0);
-	alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x4); /* Hight power */
 	alc_update_coefex_idx(codec, 0x53, 0x02, 0x8000, 1 << 15); /* Clear bit */
 	alc_update_coefex_idx(codec, 0x53, 0x02, 0x8000, 0 << 15);
 	/*
@@ -3516,32 +3638,31 @@
 	if (!hp_pin)
 		hp_pin = 0x21;
 
+	alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x1); /* Low power */
 	hp_pin_sense = snd_hda_jack_detect(codec, hp_pin);
 
-	if (hp_pin_sense)
+	if (hp_pin_sense) {
 		msleep(2);
 
-	snd_hda_codec_write(codec, hp_pin, 0,
+		snd_hda_codec_write(codec, hp_pin, 0,
 			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
 
-	if (hp_pin_sense || spec->ultra_low_power)
-		msleep(85);
+		msleep(75);
 
 	/* 3k pull low control for Headset jack. */
 	/* NOTE: call this before clearing the pin, otherwise codec stalls */
 	/* If disable 3k pulldown control for alc257, the Mic detection will not work correctly
 	 * when booting with headset plugged. So skip setting it for the codec alc257
 	 */
-	if (spec->codec_variant != ALC269_TYPE_ALC257 &&
-	    spec->codec_variant != ALC269_TYPE_ALC256)
-		alc_update_coef_idx(codec, 0x46, 0, 3 << 12);
+		if (spec->en_3kpull_low)
+			alc_update_coef_idx(codec, 0x46, 0, 3 << 12);
 
-	if (!spec->no_shutup_pins)
-		snd_hda_codec_write(codec, hp_pin, 0,
+		if (!spec->no_shutup_pins)
+			snd_hda_codec_write(codec, hp_pin, 0,
 				    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
 
-	if (hp_pin_sense || spec->ultra_low_power)
-		msleep(100);
+		msleep(75);
+	}
 
 	alc_auto_setup_eapd(codec, false);
 	alc_shutup_pins(codec);
@@ -3563,6 +3684,7 @@
 	int i, val;
 	int coef38, coef0d, coef36;
 
+	alc_write_coefex_idx(codec, 0x58, 0x00, 0x1888); /* write default value */
 	alc_update_coef_idx(codec, 0x4a, 1<<15, 1<<15); /* Reset HP JD */
 	coef38 = alc_read_coef_idx(codec, 0x38); /* Amp control */
 	coef0d = alc_read_coef_idx(codec, 0x0d); /* Digital Misc control */
@@ -3611,7 +3733,15 @@
 	hda_nid_t hp_pin = alc_get_hp_pin(spec);
 	bool hp1_pin_sense, hp2_pin_sense;
 
-	if (spec->codec_variant != ALC269_TYPE_ALC287)
+	if (spec->ultra_low_power) {
+		alc_update_coef_idx(codec, 0x08, 0x0f << 2, 3<<2);
+		alc_update_coef_idx(codec, 0x0e, 7<<6, 7<<6);
+		alc_update_coef_idx(codec, 0x33, 1<<11, 0);
+		msleep(30);
+	}
+
+	if (spec->codec_variant != ALC269_TYPE_ALC287 &&
+		spec->codec_variant != ALC269_TYPE_ALC245)
 		/* required only at boot or S3 and S4 resume time */
 		if (!spec->done_hp_init ||
 			is_s3_resume(codec) ||
@@ -3627,39 +3757,29 @@
 	hp1_pin_sense = snd_hda_jack_detect(codec, hp_pin);
 	hp2_pin_sense = snd_hda_jack_detect(codec, 0x16);
 
-	if (hp1_pin_sense || hp2_pin_sense)
+	if (hp1_pin_sense || hp2_pin_sense) {
 		msleep(2);
+		alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x1); /* Low power */
 
-	alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x1); /* Low power */
-	if (spec->ultra_low_power) {
-		alc_update_coef_idx(codec, 0x08, 0x0f << 2, 3<<2);
-		alc_update_coef_idx(codec, 0x0e, 7<<6, 7<<6);
-		alc_update_coef_idx(codec, 0x33, 1<<11, 0);
-		msleep(30);
-	}
-
-	if (hp1_pin_sense || spec->ultra_low_power)
-		snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-	if (hp2_pin_sense)
-		snd_hda_codec_write(codec, 0x16, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-
-	if (hp1_pin_sense || hp2_pin_sense || spec->ultra_low_power)
-		msleep(85);
-
-	if (hp1_pin_sense || spec->ultra_low_power)
-		snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
-	if (hp2_pin_sense)
-		snd_hda_codec_write(codec, 0x16, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x16, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+		msleep(75);
 
-	if (hp1_pin_sense || hp2_pin_sense || spec->ultra_low_power)
-		msleep(100);
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x16, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
 
-	alc_update_coef_idx(codec, 0x4a, 3 << 10, 0);
-	alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x4); /* Hight power */
+		msleep(75);
+		alc_update_coef_idx(codec, 0x4a, 3 << 10, 0);
+		alc_update_coefex_idx(codec, 0x57, 0x04, 0x0007, 0x4); /* Hight power */
+	}
 }
 
 static void alc225_shutup(struct hda_codec *codec)
@@ -3671,36 +3791,35 @@
 	if (!hp_pin)
 		hp_pin = 0x21;
 
-	alc_disable_headset_jack_key(codec);
-	/* 3k pull low control for Headset jack. */
-	alc_update_coef_idx(codec, 0x4a, 0, 3 << 10);
-
 	hp1_pin_sense = snd_hda_jack_detect(codec, hp_pin);
 	hp2_pin_sense = snd_hda_jack_detect(codec, 0x16);
 
-	if (hp1_pin_sense || hp2_pin_sense)
+	if (hp1_pin_sense || hp2_pin_sense) {
+		alc_disable_headset_jack_key(codec);
+		/* 3k pull low control for Headset jack. */
+		alc_update_coef_idx(codec, 0x4a, 0, 3 << 10);
 		msleep(2);
 
-	if (hp1_pin_sense || spec->ultra_low_power)
-		snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-	if (hp2_pin_sense)
-		snd_hda_codec_write(codec, 0x16, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-
-	if (hp1_pin_sense || hp2_pin_sense || spec->ultra_low_power)
-		msleep(85);
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x16, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
 
-	if (hp1_pin_sense || spec->ultra_low_power)
-		snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
-	if (hp2_pin_sense)
-		snd_hda_codec_write(codec, 0x16, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+		msleep(75);
 
-	if (hp1_pin_sense || hp2_pin_sense || spec->ultra_low_power)
-		msleep(100);
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x16, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
 
+		msleep(75);
+		alc_update_coef_idx(codec, 0x4a, 3 << 10, 0);
+		alc_enable_headset_jack_key(codec);
+	}
 	alc_auto_setup_eapd(codec, false);
 	alc_shutup_pins(codec);
 	if (spec->ultra_low_power) {
@@ -3711,9 +3830,79 @@
 		alc_update_coef_idx(codec, 0x4a, 3<<4, 2<<4);
 		msleep(30);
 	}
+}
+
+static void alc222_init(struct hda_codec *codec)
+{
+	struct alc_spec *spec = codec->spec;
+	hda_nid_t hp_pin = alc_get_hp_pin(spec);
+	bool hp1_pin_sense, hp2_pin_sense;
+
+	if (!hp_pin)
+		return;
 
-	alc_update_coef_idx(codec, 0x4a, 3 << 10, 0);
-	alc_enable_headset_jack_key(codec);
+	msleep(30);
+
+	hp1_pin_sense = snd_hda_jack_detect(codec, hp_pin);
+	hp2_pin_sense = snd_hda_jack_detect(codec, 0x14);
+
+	if (hp1_pin_sense || hp2_pin_sense) {
+		msleep(2);
+
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x14, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+		msleep(75);
+
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x14, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+
+		msleep(75);
+	}
+}
+
+static void alc222_shutup(struct hda_codec *codec)
+{
+	struct alc_spec *spec = codec->spec;
+	hda_nid_t hp_pin = alc_get_hp_pin(spec);
+	bool hp1_pin_sense, hp2_pin_sense;
+
+	if (!hp_pin)
+		hp_pin = 0x21;
+
+	hp1_pin_sense = snd_hda_jack_detect(codec, hp_pin);
+	hp2_pin_sense = snd_hda_jack_detect(codec, 0x14);
+
+	if (hp1_pin_sense || hp2_pin_sense) {
+		msleep(2);
+
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x14, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
+
+		msleep(75);
+
+		if (hp1_pin_sense)
+			snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+		if (hp2_pin_sense)
+			snd_hda_codec_write(codec, 0x14, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+
+		msleep(75);
+	}
+	alc_auto_setup_eapd(codec, false);
+	alc_shutup_pins(codec);
 }
 
 static void alc_default_init(struct hda_codec *codec)
@@ -3729,20 +3918,18 @@
 
 	hp_pin_sense = snd_hda_jack_detect(codec, hp_pin);
 
-	if (hp_pin_sense)
+	if (hp_pin_sense) {
 		msleep(2);
 
-	snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-
-	if (hp_pin_sense)
-		msleep(85);
+		snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
 
-	snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+		msleep(75);
 
-	if (hp_pin_sense)
-		msleep(100);
+		snd_hda_codec_write(codec, hp_pin, 0,
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+		msleep(75);
+	}
 }
 
 static void alc_default_shutup(struct hda_codec *codec)
@@ -3758,22 +3945,20 @@
 
 	hp_pin_sense = snd_hda_jack_detect(codec, hp_pin);
 
-	if (hp_pin_sense)
+	if (hp_pin_sense) {
 		msleep(2);
 
-	snd_hda_codec_write(codec, hp_pin, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-
-	if (hp_pin_sense)
-		msleep(85);
-
-	if (!spec->no_shutup_pins)
 		snd_hda_codec_write(codec, hp_pin, 0,
-				    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+				    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
 
-	if (hp_pin_sense)
-		msleep(100);
+		msleep(75);
 
+		if (!spec->no_shutup_pins)
+			snd_hda_codec_write(codec, hp_pin, 0,
+					    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+
+		msleep(75);
+	}
 	alc_auto_setup_eapd(codec, false);
 	alc_shutup_pins(codec);
 }
@@ -4355,6 +4540,16 @@
 	alc_fixup_hp_gpio_led(codec, action, 0x10, 0);
 }
 
+static void alc245_fixup_hp_gpio_led(struct hda_codec *codec,
+				const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+
+	if (action == HDA_FIXUP_ACT_PRE_PROBE)
+		spec->micmute_led_polarity = 1;
+	alc_fixup_hp_gpio_led(codec, action, 0, 0x04);
+}
+
 /* turn on/off mic-mute LED per capture hook via VREF change */
 static int vref_micmute_led_set(struct led_classdev *led_cdev,
 				enum led_brightness brightness)
@@ -4504,6 +4699,21 @@
 	}
 }
 
+static void alc236_fixup_hp_mute_led_coefbit2(struct hda_codec *codec,
+					  const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+
+	if (action == HDA_FIXUP_ACT_PRE_PROBE) {
+		spec->mute_led_polarity = 0;
+		spec->mute_led_coef.idx = 0x07;
+		spec->mute_led_coef.mask = 1;
+		spec->mute_led_coef.on = 1;
+		spec->mute_led_coef.off = 0;
+		snd_hda_gen_add_mute_led_cdev(codec, coef_mute_led_set);
+	}
+}
+
 /* turn on/off mic-mute LED per capture hook by coef bit */
 static int coef_micmute_led_set(struct led_classdev *led_cdev,
 				enum led_brightness brightness)
@@ -4530,6 +4740,16 @@
 	}
 }
 
+static void alc285_fixup_hp_gpio_micmute_led(struct hda_codec *codec,
+				const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+
+	if (action == HDA_FIXUP_ACT_PRE_PROBE)
+		spec->micmute_led_polarity = 1;
+	alc_fixup_hp_gpio_led(codec, action, 0, 0x04);
+}
+
 static void alc236_fixup_hp_coef_micmute_led(struct hda_codec *codec,
 				const struct hda_fixup *fix, int action)
 {
@@ -4544,6 +4764,21 @@
 	}
 }
 
+static void alc295_fixup_hp_mute_led_coefbit11(struct hda_codec *codec,
+				const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+
+	if (action == HDA_FIXUP_ACT_PRE_PROBE) {
+		spec->mute_led_polarity = 0;
+		spec->mute_led_coef.idx = 0xb;
+		spec->mute_led_coef.mask = 3 << 3;
+		spec->mute_led_coef.on = 1 << 3;
+		spec->mute_led_coef.off = 1 << 4;
+		snd_hda_gen_add_mute_led_cdev(codec, coef_mute_led_set);
+	}
+}
+
 static void alc285_fixup_hp_mute_led(struct hda_codec *codec,
 				const struct hda_fixup *fix, int action)
 {
@@ -4551,6 +4786,13 @@
 	alc285_fixup_hp_coef_micmute_led(codec, fix, action);
 }
 
+static void alc285_fixup_hp_spectre_x360_mute_led(struct hda_codec *codec,
+				const struct hda_fixup *fix, int action)
+{
+	alc285_fixup_hp_mute_led_coefbit(codec, fix, action);
+	alc285_fixup_hp_gpio_micmute_led(codec, fix, action);
+}
+
 static void alc236_fixup_hp_mute_led(struct hda_codec *codec,
 				const struct hda_fixup *fix, int action)
 {
@@ -4577,6 +4819,48 @@
 	alc236_fixup_hp_micmute_led_vref(codec, fix, action);
 }
 
+static inline void alc298_samsung_write_coef_pack(struct hda_codec *codec,
+						  const unsigned short coefs[2])
+{
+	alc_write_coef_idx(codec, 0x23, coefs[0]);
+	alc_write_coef_idx(codec, 0x25, coefs[1]);
+	alc_write_coef_idx(codec, 0x26, 0xb011);
+}
+
+struct alc298_samsung_amp_desc {
+	unsigned char nid;
+	unsigned short init_seq[2][2];
+};
+
+static void alc298_fixup_samsung_amp(struct hda_codec *codec,
+				     const struct hda_fixup *fix, int action)
+{
+	int i, j;
+	static const unsigned short init_seq[][2] = {
+		{ 0x19, 0x00 }, { 0x20, 0xc0 }, { 0x22, 0x44 }, { 0x23, 0x08 },
+		{ 0x24, 0x85 }, { 0x25, 0x41 }, { 0x35, 0x40 }, { 0x36, 0x01 },
+		{ 0x38, 0x81 }, { 0x3a, 0x03 }, { 0x3b, 0x81 }, { 0x40, 0x3e },
+		{ 0x41, 0x07 }, { 0x400, 0x1 }
+	};
+	static const struct alc298_samsung_amp_desc amps[] = {
+		{ 0x3a, { { 0x18, 0x1 }, { 0x26, 0x0 } } },
+		{ 0x39, { { 0x18, 0x2 }, { 0x26, 0x1 } } }
+	};
+
+	if (action != HDA_FIXUP_ACT_INIT)
+		return;
+
+	for (i = 0; i < ARRAY_SIZE(amps); i++) {
+		alc_write_coef_idx(codec, 0x22, amps[i].nid);
+
+		for (j = 0; j < ARRAY_SIZE(amps[i].init_seq); j++)
+			alc298_samsung_write_coef_pack(codec, amps[i].init_seq[j]);
+
+		for (j = 0; j < ARRAY_SIZE(init_seq); j++)
+			alc298_samsung_write_coef_pack(codec, init_seq[j]);
+	}
+}
+
 #if IS_REACHABLE(CONFIG_INPUT)
 static void gpio2_mic_hotkey_event(struct hda_codec *codec,
 				   struct hda_jack_callback *event)
@@ -4703,6 +4987,30 @@
 	}
 }
 
+static void alc_hp_mute_disable(struct hda_codec *codec, unsigned int delay)
+{
+	if (delay <= 0)
+		delay = 75;
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
+	msleep(delay);
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+	msleep(delay);
+}
+
+static void alc_hp_enable_unmute(struct hda_codec *codec, unsigned int delay)
+{
+	if (delay <= 0)
+		delay = 75;
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+	msleep(delay);
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+	msleep(delay);
+}
+
 static const struct coef_fw alc225_pre_hsmode[] = {
 	UPDATE_COEF(0x4a, 1<<8, 0),
 	UPDATE_COEFEX(0x57, 0x05, 1<<14, 0),
@@ -4803,6 +5111,8 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
+		alc_hp_mute_disable(codec, 75);
 		alc_process_coef_fw(codec, coef0256);
 		break;
 	case 0x10ec0234:
@@ -4837,6 +5147,7 @@
 	case 0x10ec0295:
 	case 0x10ec0289:
 	case 0x10ec0299:
+		alc_hp_mute_disable(codec, 75);
 		alc_process_coef_fw(codec, alc225_pre_hsmode);
 		alc_process_coef_fw(codec, coef0225);
 		break;
@@ -4918,6 +5229,7 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		alc_write_coef_idx(codec, 0x45, 0xc489);
 		snd_hda_set_pin_ctl_cache(codec, hp_pin, 0);
 		alc_process_coef_fw(codec, coef0256);
@@ -5061,6 +5373,7 @@
 	case 0x10ec0299:
 		alc_process_coef_fw(codec, alc225_pre_hsmode);
 		alc_process_coef_fw(codec, coef0225);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0255:
 		alc_process_coef_fw(codec, coef0255);
@@ -5068,10 +5381,12 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		alc_write_coef_idx(codec, 0x1b, 0x0e4b);
 		alc_write_coef_idx(codec, 0x45, 0xc089);
 		msleep(50);
 		alc_process_coef_fw(codec, coef0256);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5167,7 +5482,9 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		alc_process_coef_fw(codec, coef0256);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5216,6 +5533,7 @@
 			alc_process_coef_fw(codec, coef0225_2);
 		else
 			alc_process_coef_fw(codec, coef0225_1);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0867:
 		alc_update_coefex_idx(codec, 0x57, 0x5, 1<<14, 0);
@@ -5281,7 +5599,9 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		alc_process_coef_fw(codec, coef0256);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5319,6 +5639,7 @@
 	case 0x10ec0289:
 	case 0x10ec0299:
 		alc_process_coef_fw(codec, coef0225);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	}
 	codec_dbg(codec, "Headset jack set to Nokia-style headset mode.\n");
@@ -5382,29 +5703,26 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		alc_write_coef_idx(codec, 0x1b, 0x0e4b);
 		alc_write_coef_idx(codec, 0x06, 0x6104);
 		alc_write_coefex_idx(codec, 0x57, 0x3, 0x09a3);
 
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
-
 		alc_process_coef_fw(codec, coef0255);
 		msleep(300);
 		val = alc_read_coef_idx(codec, 0x46);
 		is_ctia = (val & 0x0070) == 0x0070;
-
+		if (!is_ctia) {
+			alc_write_coef_idx(codec, 0x45, 0xe089);
+			msleep(100);
+			val = alc_read_coef_idx(codec, 0x46);
+			if ((val & 0x0070) == 0x0070)
+				is_ctia = false;
+			else
+				is_ctia = true;
+		}
 		alc_write_coefex_idx(codec, 0x57, 0x3, 0x0da3);
 		alc_update_coefex_idx(codec, 0x57, 0x5, 1<<14, 0);
-
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5481,12 +5799,6 @@
 	case 0x10ec0295:
 	case 0x10ec0289:
 	case 0x10ec0299:
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
-
 		alc_process_coef_fw(codec, alc225_pre_hsmode);
 		alc_update_coef_idx(codec, 0x67, 0xf000, 0x1000);
 		val = alc_read_coef_idx(codec, 0x45);
@@ -5503,15 +5815,19 @@
 			val = alc_read_coef_idx(codec, 0x46);
 			is_ctia = (val & 0x00f0) == 0x00f0;
 		}
+		if (!is_ctia) {
+			alc_update_coef_idx(codec, 0x45, 0x3f<<10, 0x38<<10);
+			alc_update_coef_idx(codec, 0x49, 3<<8, 1<<8);
+			msleep(100);
+			val = alc_read_coef_idx(codec, 0x46);
+			if ((val & 0x00f0) == 0x00f0)
+				is_ctia = false;
+			else
+				is_ctia = true;
+		}
 		alc_update_coef_idx(codec, 0x4a, 7<<6, 7<<6);
 		alc_update_coef_idx(codec, 0x4a, 3<<4, 3<<4);
 		alc_update_coef_idx(codec, 0x67, 0xf000, 0x3000);
-
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
 		break;
 	case 0x10ec0867:
 		is_ctia = true;
@@ -5676,6 +5992,7 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		alc_process_coef_fw(codec, alc256fw);
 		break;
 	}
@@ -6278,6 +6595,8 @@
 	case 0x10ec0236:
 	case 0x10ec0255:
 	case 0x10ec0256:
+	case 0x10ec0257:
+	case 0x19e58326:
 		alc_update_coef_idx(codec, 0x1b, 0x8000, 1 << 15); /* Reset HP JD */
 		alc_update_coef_idx(codec, 0x1b, 0x8000, 0 << 15);
 		break;
@@ -6462,6 +6781,60 @@
 	}
 }
 
+static void alc285_fixup_hp_envy_x360(struct hda_codec *codec,
+				      const struct hda_fixup *fix,
+				      int action)
+{
+	static const struct coef_fw coefs[] = {
+		WRITE_COEF(0x08, 0x6a0c), WRITE_COEF(0x0d, 0xa023),
+		WRITE_COEF(0x10, 0x0320), WRITE_COEF(0x1a, 0x8c03),
+		WRITE_COEF(0x25, 0x1800), WRITE_COEF(0x26, 0x003a),
+		WRITE_COEF(0x28, 0x1dfe), WRITE_COEF(0x29, 0xb014),
+		WRITE_COEF(0x2b, 0x1dfe), WRITE_COEF(0x37, 0xfe15),
+		WRITE_COEF(0x38, 0x7909), WRITE_COEF(0x45, 0xd489),
+		WRITE_COEF(0x46, 0x00f4), WRITE_COEF(0x4a, 0x21e0),
+		WRITE_COEF(0x66, 0x03f0), WRITE_COEF(0x67, 0x1000),
+		WRITE_COEF(0x6e, 0x1005), { }
+	};
+
+	static const struct hda_pintbl pincfgs[] = {
+		{ 0x12, 0xb7a60130 },  /* Internal microphone*/
+		{ 0x14, 0x90170150 },  /* B&O soundbar speakers */
+		{ 0x17, 0x90170153 },  /* Side speakers */
+		{ 0x19, 0x03a11040 },  /* Headset microphone */
+		{ }
+	};
+
+	switch (action) {
+	case HDA_FIXUP_ACT_PRE_PROBE:
+		snd_hda_apply_pincfgs(codec, pincfgs);
+
+		/* Fixes volume control problem for side speakers */
+		alc295_fixup_disable_dac3(codec, fix, action);
+
+		/* Fixes no sound from headset speaker */
+		snd_hda_codec_amp_stereo(codec, 0x21, HDA_OUTPUT, 0, -1, 0);
+
+		/* Auto-enable headset mic when plugged */
+		snd_hda_jack_set_gating_jack(codec, 0x19, 0x21);
+
+		/* Headset mic volume enhancement */
+		snd_hda_codec_set_pin_target(codec, 0x19, PIN_VREF50);
+		break;
+	case HDA_FIXUP_ACT_INIT:
+		alc_process_coef_fw(codec, coefs);
+		break;
+	case HDA_FIXUP_ACT_BUILD:
+		rename_ctl(codec, "Bass Speaker Playback Volume",
+			   "B&O-Tuned Playback Volume");
+		rename_ctl(codec, "Front Playback Switch",
+			   "B&O Soundbar Playback Switch");
+		rename_ctl(codec, "Bass Speaker Playback Switch",
+			   "Side Speaker Playback Switch");
+		break;
+	}
+}
+
 /* for hda_fixup_thinkpad_acpi() */
 #include "thinkpad_helper.c"
 
@@ -6486,30 +6859,277 @@
 	}
 }
 
+static int comp_match_dev_name(struct device *dev, void *data)
+{
+	return strcmp(dev_name(dev), data) == 0;
+}
+
+static int find_comp_by_dev_name(struct alc_spec *spec, const char *name)
+{
+	int i;
+
+	for (i = 0; i < HDA_MAX_COMPONENTS; i++) {
+		if (strcmp(spec->comps[i].name, name) == 0)
+			return i;
+	}
+
+	return -ENODEV;
+}
+
+static int comp_bind(struct device *dev)
+{
+	struct hda_codec *cdc = dev_to_hda_codec(dev);
+	struct alc_spec *spec = cdc->spec;
+
+	return component_bind_all(dev, spec->comps);
+}
+
+static void comp_unbind(struct device *dev)
+{
+	struct hda_codec *cdc = dev_to_hda_codec(dev);
+	struct alc_spec *spec = cdc->spec;
+
+	component_unbind_all(dev, spec->comps);
+}
+
+static const struct component_master_ops comp_master_ops = {
+	.bind = comp_bind,
+	.unbind = comp_unbind,
+};
+
+static void comp_generic_playback_hook(struct hda_pcm_stream *hinfo, struct hda_codec *cdc,
+				       struct snd_pcm_substream *sub, int action)
+{
+	struct alc_spec *spec = cdc->spec;
+	int i;
+
+	for (i = 0; i < HDA_MAX_COMPONENTS; i++) {
+		if (spec->comps[i].dev)
+			spec->comps[i].playback_hook(spec->comps[i].dev, action);
+	}
+}
+
+static void cs35l41_generic_fixup(struct hda_codec *cdc, int action, const char *bus,
+				  const char *hid, int count)
+{
+	struct device *dev = hda_codec_dev(cdc);
+	struct alc_spec *spec = cdc->spec;
+	char *name;
+	int ret, i;
+
+	switch (action) {
+	case HDA_FIXUP_ACT_PRE_PROBE:
+		for (i = 0; i < count; i++) {
+			name = devm_kasprintf(dev, GFP_KERNEL,
+					      "%s-%s:00-cs35l41-hda.%d", bus, hid, i);
+			if (!name)
+				return;
+			component_match_add(dev, &spec->match, comp_match_dev_name, name);
+		}
+		ret = component_master_add_with_match(dev, &comp_master_ops, spec->match);
+		if (ret)
+			codec_err(cdc, "Fail to register component aggregator %d\n", ret);
+		else
+			spec->gen.pcm_playback_hook = comp_generic_playback_hook;
+		break;
+	}
+}
+
+static void cs35l41_fixup_i2c_two(struct hda_codec *cdc, const struct hda_fixup *fix, int action)
+{
+	cs35l41_generic_fixup(cdc, action, "i2c", "CSC3551", 2);
+}
+
+static void cs35l41_fixup_spi_two(struct hda_codec *codec, const struct hda_fixup *fix, int action)
+{
+	cs35l41_generic_fixup(codec, action, "spi0", "CSC3551", 2);
+}
+
+static void cs35l41_fixup_spi_four(struct hda_codec *codec, const struct hda_fixup *fix, int action)
+{
+	cs35l41_generic_fixup(codec, action, "spi0", "CSC3551", 4);
+}
+
+static void alc287_legion_16achg6_playback_hook(struct hda_pcm_stream *hinfo, struct hda_codec *cdc,
+						struct snd_pcm_substream *sub, int action)
+{
+	struct alc_spec *spec = cdc->spec;
+	unsigned int rx_slot;
+	int i;
+
+	switch (action) {
+	case HDA_GEN_PCM_ACT_PREPARE:
+		rx_slot = 0;
+		i = find_comp_by_dev_name(spec, "i2c-CLSA0100:00-cs35l41-hda.0");
+		if (i >= 0)
+			spec->comps[i].set_channel_map(spec->comps[i].dev, 0, NULL, 1, &rx_slot);
+
+		rx_slot = 1;
+		i = find_comp_by_dev_name(spec, "i2c-CLSA0100:00-cs35l41-hda.1");
+		if (i >= 0)
+			spec->comps[i].set_channel_map(spec->comps[i].dev, 0, NULL, 1, &rx_slot);
+		break;
+	}
+
+	comp_generic_playback_hook(hinfo, cdc, sub, action);
+}
+
+static void alc287_fixup_legion_16achg6_speakers(struct hda_codec *cdc, const struct hda_fixup *fix,
+						 int action)
+{
+	struct device *dev = hda_codec_dev(cdc);
+	struct alc_spec *spec = cdc->spec;
+	int ret;
+
+	switch (action) {
+	case HDA_FIXUP_ACT_PRE_PROBE:
+		component_match_add(dev, &spec->match, comp_match_dev_name,
+				    "i2c-CLSA0100:00-cs35l41-hda.0");
+		component_match_add(dev, &spec->match, comp_match_dev_name,
+				    "i2c-CLSA0100:00-cs35l41-hda.1");
+		ret = component_master_add_with_match(dev, &comp_master_ops, spec->match);
+		if (ret)
+			codec_err(cdc, "Fail to register component aggregator %d\n", ret);
+		else
+			spec->gen.pcm_playback_hook = alc287_legion_16achg6_playback_hook;
+		break;
+	}
+}
+
 /* for alc295_fixup_hp_top_speakers */
 #include "hp_x360_helper.c"
 
 /* for alc285_fixup_ideapad_s740_coef() */
 #include "ideapad_s740_helper.c"
 
-static void alc256_fixup_tongfang_reset_persistent_settings(struct hda_codec *codec,
-							    const struct hda_fixup *fix,
-							    int action)
+static const struct coef_fw alc256_fixup_set_coef_defaults_coefs[] = {
+	WRITE_COEF(0x10, 0x0020), WRITE_COEF(0x24, 0x0000),
+	WRITE_COEF(0x26, 0x0000), WRITE_COEF(0x29, 0x3000),
+	WRITE_COEF(0x37, 0xfe05), WRITE_COEF(0x45, 0x5089),
+	{}
+};
+
+static void alc256_fixup_set_coef_defaults(struct hda_codec *codec,
+					   const struct hda_fixup *fix,
+					   int action)
 {
 	/*
-	* A certain other OS sets these coeffs to different values. On at least one TongFang
-	* barebone these settings might survive even a cold reboot. So to restore a clean slate the
-	* values are explicitly reset to default here. Without this, the external microphone is
-	* always in a plugged-in state, while the internal microphone is always in an unplugged
-	* state, breaking the ability to use the internal microphone.
-	*/
-	alc_write_coef_idx(codec, 0x24, 0x0000);
-	alc_write_coef_idx(codec, 0x26, 0x0000);
-	alc_write_coef_idx(codec, 0x29, 0x3000);
-	alc_write_coef_idx(codec, 0x37, 0xfe05);
-	alc_write_coef_idx(codec, 0x45, 0x5089);
+	 * A certain other OS sets these coeffs to different values. On at least
+	 * one TongFang barebone these settings might survive even a cold
+	 * reboot. So to restore a clean slate the values are explicitly reset
+	 * to default here. Without this, the external microphone is always in a
+	 * plugged-in state, while the internal microphone is always in an
+	 * unplugged state, breaking the ability to use the internal microphone.
+	 */
+	alc_process_coef_fw(codec, alc256_fixup_set_coef_defaults_coefs);
 }
 
+static const struct coef_fw alc233_fixup_no_audio_jack_coefs[] = {
+	WRITE_COEF(0x1a, 0x9003), WRITE_COEF(0x1b, 0x0e2b), WRITE_COEF(0x37, 0xfe06),
+	WRITE_COEF(0x38, 0x4981), WRITE_COEF(0x45, 0xd489), WRITE_COEF(0x46, 0x0074),
+	WRITE_COEF(0x49, 0x0149),
+	{}
+};
+
+static void alc233_fixup_no_audio_jack(struct hda_codec *codec,
+				       const struct hda_fixup *fix,
+				       int action)
+{
+	/*
+	 * The audio jack input and output is not detected on the ASRock NUC Box
+	 * 1100 series when cold booting without this fix. Warm rebooting from a
+	 * certain other OS makes the audio functional, as COEF settings are
+	 * preserved in this case. This fix sets these altered COEF values as
+	 * the default.
+	 */
+	alc_process_coef_fw(codec, alc233_fixup_no_audio_jack_coefs);
+}
+
+static void alc256_fixup_mic_no_presence_and_resume(struct hda_codec *codec,
+						    const struct hda_fixup *fix,
+						    int action)
+{
+	/*
+	 * The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec,
+	 * but uses the 0x8686 subproduct id in both cases. The ALC256 codec
+	 * needs an additional quirk for sound working after suspend and resume.
+	 */
+	if (codec->core.vendor_id == 0x10ec0256) {
+		alc_update_coef_idx(codec, 0x10, 1<<9, 0);
+		snd_hda_codec_set_pincfg(codec, 0x19, 0x04a11120);
+	} else {
+		snd_hda_codec_set_pincfg(codec, 0x1a, 0x04a1113c);
+	}
+}
+
+static void alc256_decrease_headphone_amp_val(struct hda_codec *codec,
+					      const struct hda_fixup *fix, int action)
+{
+	u32 caps;
+	u8 nsteps, offs;
+
+	if (action != HDA_FIXUP_ACT_PRE_PROBE)
+		return;
+
+	caps = query_amp_caps(codec, 0x3, HDA_OUTPUT);
+	nsteps = ((caps & AC_AMPCAP_NUM_STEPS) >> AC_AMPCAP_NUM_STEPS_SHIFT) - 10;
+	offs = ((caps & AC_AMPCAP_OFFSET) >> AC_AMPCAP_OFFSET_SHIFT) - 10;
+	caps &= ~AC_AMPCAP_NUM_STEPS & ~AC_AMPCAP_OFFSET;
+	caps |= (nsteps << AC_AMPCAP_NUM_STEPS_SHIFT) | (offs << AC_AMPCAP_OFFSET_SHIFT);
+
+	if (snd_hda_override_amp_caps(codec, 0x3, HDA_OUTPUT, caps))
+		codec_warn(codec, "failed to override amp caps for NID 0x3\n");
+}
+
+static void alc295_fixup_dell_inspiron_top_speakers(struct hda_codec *codec,
+					  const struct hda_fixup *fix, int action)
+{
+	static const struct hda_pintbl pincfgs[] = {
+		{ 0x14, 0x90170151 },
+		{ 0x17, 0x90170150 },
+		{ }
+	};
+	static const hda_nid_t conn[] = { 0x02, 0x03 };
+	static const hda_nid_t preferred_pairs[] = {
+		0x14, 0x02,
+		0x17, 0x03,
+		0x21, 0x02,
+		0
+	};
+	struct alc_spec *spec = codec->spec;
+
+	alc_fixup_no_shutup(codec, fix, action);
+
+	switch (action) {
+	case HDA_FIXUP_ACT_PRE_PROBE:
+		snd_hda_apply_pincfgs(codec, pincfgs);
+		snd_hda_override_conn_list(codec, 0x17, ARRAY_SIZE(conn), conn);
+		spec->gen.preferred_dacs = preferred_pairs;
+		break;
+	}
+}
+
+/* Forcibly assign NID 0x03 to HP while NID 0x02 to SPK */
+static void alc287_fixup_bind_dacs(struct hda_codec *codec,
+				    const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+	static const hda_nid_t conn[] = { 0x02, 0x03 }; /* exclude 0x06 */
+	static const hda_nid_t preferred_pairs[] = {
+		0x17, 0x02, 0x21, 0x03, 0
+	};
+
+	if (action != HDA_FIXUP_ACT_PRE_PROBE)
+		return;
+
+	snd_hda_override_conn_list(codec, 0x17, ARRAY_SIZE(conn), conn);
+	spec->gen.preferred_dacs = preferred_pairs;
+	spec->gen.auto_mute_via_amp = 1;
+	snd_hda_codec_write_cache(codec, 0x14, 0, AC_VERB_SET_PIN_WIDGET_CONTROL,
+			    0x0); /* Make sure 0x14 was disable */
+}
+
+
 enum {
 	ALC269_FIXUP_GPIO2,
 	ALC269_FIXUP_SONY_VAIO,
@@ -6564,6 +7184,7 @@
 	ALC269_FIXUP_LIMIT_INT_MIC_BOOST,
 	ALC269VB_FIXUP_ASUS_ZENBOOK,
 	ALC269VB_FIXUP_ASUS_ZENBOOK_UX31A,
+	ALC269VB_FIXUP_ASUS_MIC_NO_PRESENCE,
 	ALC269_FIXUP_LIMIT_INT_MIC_BOOST_MUTE_LED,
 	ALC269VB_FIXUP_ORDISSIMO_EVE2,
 	ALC283_FIXUP_CHROME_BOOK,
@@ -6574,8 +7195,12 @@
 	ALC290_FIXUP_MONO_SPEAKERS_HSJACK,
 	ALC290_FIXUP_SUBWOOFER,
 	ALC290_FIXUP_SUBWOOFER_HSJACK,
+	ALC295_FIXUP_HP_MUTE_LED_COEFBIT11,
 	ALC269_FIXUP_THINKPAD_ACPI,
 	ALC269_FIXUP_DMIC_THINKPAD_ACPI,
+	ALC269VB_FIXUP_INFINIX_ZERO_BOOK_13,
+	ALC269VC_FIXUP_INFINIX_Y4_MAX,
+	ALC269VB_FIXUP_CHUWI_COREBOOK_XPRO,
 	ALC255_FIXUP_ACER_MIC_NO_PRESENCE,
 	ALC255_FIXUP_ASUS_MIC_NO_PRESENCE,
 	ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
@@ -6597,6 +7222,7 @@
 	ALC280_FIXUP_HP_9480M,
 	ALC245_FIXUP_HP_X360_AMP,
 	ALC285_FIXUP_HP_SPECTRE_X360_EB1,
+	ALC285_FIXUP_HP_ENVY_X360,
 	ALC288_FIXUP_DELL_HEADSET_MODE,
 	ALC288_FIXUP_DELL1_MIC_NO_PRESENCE,
 	ALC288_FIXUP_DELL_XPS_13,
@@ -6623,6 +7249,7 @@
 	ALC298_FIXUP_LENOVO_SPK_VOLUME,
 	ALC256_FIXUP_DELL_INSPIRON_7559_SUBWOOFER,
 	ALC269_FIXUP_ATIV_BOOK_8,
+	ALC221_FIXUP_HP_288PRO_MIC_NO_PRESENCE,
 	ALC221_FIXUP_HP_MIC_NO_PRESENCE,
 	ALC256_FIXUP_ASUS_HEADSET_MODE,
 	ALC256_FIXUP_ASUS_MIC,
@@ -6662,6 +7289,7 @@
 	ALC286_FIXUP_ACER_AIO_HEADSET_MIC,
 	ALC256_FIXUP_ASUS_HEADSET_MIC,
 	ALC256_FIXUP_ASUS_MIC_NO_PRESENCE,
+	ALC255_FIXUP_PREDATOR_SUBWOOFER,
 	ALC299_FIXUP_PREDATOR_SPK,
 	ALC256_FIXUP_MEDION_HEADSET_NO_PRESENCE,
 	ALC289_FIXUP_DELL_SPK2,
@@ -6678,12 +7306,19 @@
 	ALC294_FIXUP_ASUS_GU502_HP,
 	ALC294_FIXUP_ASUS_GU502_PINS,
 	ALC294_FIXUP_ASUS_GU502_VERBS,
+	ALC294_FIXUP_ASUS_G513_PINS,
+	ALC285_FIXUP_ASUS_G533Z_PINS,
 	ALC285_FIXUP_HP_GPIO_LED,
 	ALC285_FIXUP_HP_MUTE_LED,
+	ALC285_FIXUP_HP_SPECTRE_X360_MUTE_LED,
+	ALC236_FIXUP_HP_MUTE_LED_COEFBIT2,
 	ALC236_FIXUP_HP_GPIO_LED,
 	ALC236_FIXUP_HP_MUTE_LED,
 	ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF,
+	ALC236_FIXUP_LENOVO_INV_DMIC,
+	ALC298_FIXUP_SAMSUNG_AMP,
 	ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET,
+	ALC256_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET,
 	ALC295_FIXUP_ASUS_MIC_NO_PRESENCE,
 	ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS,
 	ALC269VC_FIXUP_ACER_HEADSET_MIC,
@@ -6709,6 +7344,7 @@
 	ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK,
 	ALC287_FIXUP_HP_GPIO_LED,
 	ALC256_FIXUP_HP_HEADSET_MIC,
+	ALC245_FIXUP_HP_GPIO_LED,
 	ALC236_FIXUP_DELL_AIO_HEADSET_MIC,
 	ALC282_FIXUP_ACER_DISABLE_LINEOUT,
 	ALC255_FIXUP_ACER_LIMIT_INT_MIC_BOOST,
@@ -6725,9 +7361,44 @@
 	ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS,
 	ALC287_FIXUP_LEGION_15IMHG05_AUTOMUTE,
 	ALC287_FIXUP_YOGA7_14ITL_SPEAKERS,
+	ALC298_FIXUP_LENOVO_C940_DUET7,
 	ALC287_FIXUP_13S_GEN2_SPEAKERS,
-	ALC256_FIXUP_TONGFANG_RESET_PERSISTENT_SETTINGS,
-};
+	ALC256_FIXUP_SET_COEF_DEFAULTS,
+	ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE,
+	ALC233_FIXUP_NO_AUDIO_JACK,
+	ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME,
+	ALC285_FIXUP_LEGION_Y9000X_SPEAKERS,
+	ALC285_FIXUP_LEGION_Y9000X_AUTOMUTE,
+	ALC287_FIXUP_LEGION_16ACHG6,
+	ALC287_FIXUP_CS35L41_I2C_2,
+	ALC287_FIXUP_CS35L41_I2C_2_HP_GPIO_LED,
+	ALC245_FIXUP_CS35L41_SPI_2,
+	ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED,
+	ALC245_FIXUP_CS35L41_SPI_4,
+	ALC245_FIXUP_CS35L41_SPI_4_HP_GPIO_LED,
+	ALC285_FIXUP_HP_SPEAKERS_MICMUTE_LED,
+	ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS,
+	ALC236_FIXUP_DELL_DUAL_CODECS,
+	ALC287_FIXUP_THINKPAD_I2S_SPK,
+	ALC256_FIXUP_HEADPHONE_AMP_VOL,
+};
+
+/* A special fixup for Lenovo C940 and Yoga Duet 7;
+ * both have the very same PCI SSID, and we need to apply different fixups
+ * depending on the codec ID
+ */
+static void alc298_fixup_lenovo_c940_duet7(struct hda_codec *codec,
+					   const struct hda_fixup *fix,
+					   int action)
+{
+	int id;
+
+	if (codec->core.vendor_id == 0x10ec0298)
+		id = ALC298_FIXUP_LENOVO_SPK_VOLUME; /* C940 */
+	else
+		id = ALC287_FIXUP_YOGA7_14ITL_SPEAKERS; /* Duet 7 */
+	__snd_hda_apply_fixup(codec, id, action, 0);
+}
 
 static const struct hda_fixup alc269_fixups[] = {
 	[ALC269_FIXUP_GPIO2] = {
@@ -6840,6 +7511,33 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc269_fixup_pincfg_U7x7_headset_mic,
 	},
+	[ALC269VB_FIXUP_INFINIX_ZERO_BOOK_13] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x14, 0x90170151 }, /* use as internal speaker (LFE) */
+			{ 0x1b, 0x90170152 }, /* use as internal speaker (back) */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC269_FIXUP_LIMIT_INT_MIC_BOOST
+	},
+	[ALC269VC_FIXUP_INFINIX_Y4_MAX] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x1b, 0x90170150 }, /* use as internal speaker */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC269_FIXUP_LIMIT_INT_MIC_BOOST
+	},
+	[ALC269VB_FIXUP_CHUWI_COREBOOK_XPRO] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x18, 0x03a19020 }, /* headset mic */
+			{ 0x1b, 0x90170150 }, /* speaker */
+			{ }
+		},
+	},
 	[ALC269_FIXUP_AMIC] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
@@ -7114,6 +7812,15 @@
 		.chained = true,
 		.chain_id = ALC269VB_FIXUP_ASUS_ZENBOOK,
 	},
+	[ALC269VB_FIXUP_ASUS_MIC_NO_PRESENCE] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x18, 0x01a110f0 },  /* use as headset mic */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC269_FIXUP_HEADSET_MIC
+	},
 	[ALC269_FIXUP_LIMIT_INT_MIC_BOOST_MUTE_LED] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc269_fixup_limit_int_mic_boost,
@@ -7333,6 +8040,8 @@
 	[ALC245_FIXUP_HP_X360_AMP] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc245_fixup_hp_x360_amp,
+		.chained = true,
+		.chain_id = ALC245_FIXUP_HP_GPIO_LED
 	},
 	[ALC288_FIXUP_DELL_HEADSET_MODE] = {
 		.type = HDA_FIXUP_FUNC,
@@ -7523,6 +8232,16 @@
 		.chained = true,
 		.chain_id = ALC269_FIXUP_NO_SHUTUP
 	},
+	[ALC221_FIXUP_HP_288PRO_MIC_NO_PRESENCE] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x19, 0x01a1913c }, /* use as headset mic, without its own jack detect */
+			{ 0x1a, 0x01813030 }, /* use as headphone mic, without its own jack detect */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC269_FIXUP_HEADSET_MODE
+	},
 	[ALC221_FIXUP_HP_MIC_NO_PRESENCE] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
@@ -7834,6 +8553,13 @@
 		.chained = true,
 		.chain_id = ALC256_FIXUP_ASUS_HEADSET_MODE
 	},
+	[ALC255_FIXUP_PREDATOR_SUBWOOFER] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x17, 0x90170151 }, /* use as internal speaker (LFE) */
+			{ 0x1b, 0x90170152 } /* use as internal speaker (back) */
+		}
+	},
 	[ALC299_FIXUP_PREDATOR_SPK] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
@@ -7958,6 +8684,26 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc294_fixup_gu502_hp,
 	},
+	 [ALC294_FIXUP_ASUS_G513_PINS] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+				{ 0x19, 0x03a11050 }, /* front HP mic */
+				{ 0x1a, 0x03a11c30 }, /* rear external mic */
+				{ 0x21, 0x03211420 }, /* front HP out */
+				{ }
+		},
+	},
+	[ALC285_FIXUP_ASUS_G533Z_PINS] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x14, 0x90170152 }, /* Speaker Surround Playback Switch */
+			{ 0x19, 0x03a19020 }, /* Mic Boost Volume */
+			{ 0x1a, 0x03a11c30 }, /* Mic Boost Volume */
+			{ 0x1e, 0x90170151 }, /* Rear jack, IN OUT EAPD Detect */
+			{ 0x21, 0x03211420 },
+			{ }
+		},
+	},
 	[ALC294_FIXUP_ASUS_COEF_1B] = {
 		.type = HDA_FIXUP_VERBS,
 		.v.verbs = (const struct hda_verb[]) {
@@ -7979,6 +8725,14 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc285_fixup_hp_mute_led,
 	},
+	[ALC285_FIXUP_HP_SPECTRE_X360_MUTE_LED] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc285_fixup_hp_spectre_x360_mute_led,
+	},
+	[ALC236_FIXUP_HP_MUTE_LED_COEFBIT2] = {
+	    .type = HDA_FIXUP_FUNC,
+	    .v.func = alc236_fixup_hp_mute_led_coefbit2,
+	},
 	[ALC236_FIXUP_HP_GPIO_LED] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc236_fixup_hp_gpio_led,
@@ -7991,6 +8745,22 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc236_fixup_hp_mute_led_micmute_vref,
 	},
+	[ALC236_FIXUP_LENOVO_INV_DMIC] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc_fixup_inv_dmic,
+		.chained = true,
+		.chain_id = ALC283_FIXUP_INT_MIC,
+	},
+	[ALC295_FIXUP_HP_MUTE_LED_COEFBIT11] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc295_fixup_hp_mute_led_coefbit11,
+	},
+	[ALC298_FIXUP_SAMSUNG_AMP] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc298_fixup_samsung_amp,
+		.chained = true,
+		.chain_id = ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET
+	},
 	[ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET] = {
 		.type = HDA_FIXUP_VERBS,
 		.v.verbs = (const struct hda_verb[]) {
@@ -7998,6 +8768,14 @@
 			{ }
 		},
 	},
+	[ALC256_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET] = {
+		.type = HDA_FIXUP_VERBS,
+		.v.verbs = (const struct hda_verb[]) {
+			{ 0x20, AC_VERB_SET_COEF_INDEX, 0x08},
+			{ 0x20, AC_VERB_SET_PROC_COEF, 0x2fcf},
+			{ }
+		},
+	},
 	[ALC295_FIXUP_ASUS_MIC_NO_PRESENCE] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
@@ -8294,6 +9072,12 @@
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc285_fixup_hp_spectre_x360_eb1
 	},
+	[ALC285_FIXUP_HP_ENVY_X360] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc285_fixup_hp_envy_x360,
+		.chained = true,
+		.chain_id = ALC285_FIXUP_HP_GPIO_AMP_INIT,
+	},
 	[ALC287_FIXUP_IDEAPAD_BASS_SPK_AMP] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc285_fixup_ideapad_s740_coef,
@@ -8321,6 +9105,18 @@
 		.chained = true,
 		.chain_id = ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF,
 	},
+	[ALC285_FIXUP_LEGION_Y9000X_SPEAKERS] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc285_fixup_ideapad_s740_coef,
+		.chained = true,
+		.chain_id = ALC285_FIXUP_LEGION_Y9000X_AUTOMUTE,
+	},
+	[ALC285_FIXUP_LEGION_Y9000X_AUTOMUTE] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc287_fixup_legion_15imhg05_speakers,
+		.chained = true,
+		.chain_id = ALC269_FIXUP_THINKPAD_ACPI,
+	},
 	[ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS] = {
 		.type = HDA_FIXUP_VERBS,
 		//.v.verbs = legion_15imhg05_coefs,
@@ -8406,6 +9202,10 @@
 		.chained = true,
 		.chain_id = ALC269_FIXUP_HEADSET_MODE,
 	},
+	[ALC298_FIXUP_LENOVO_C940_DUET7] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc298_fixup_lenovo_c940_duet7,
+	},
 	[ALC287_FIXUP_13S_GEN2_SPEAKERS] = {
 		.type = HDA_FIXUP_VERBS,
 		.v.verbs = (const struct hda_verb[]) {
@@ -8428,9 +9228,98 @@
 		.chained = true,
 		.chain_id = ALC269_FIXUP_HEADSET_MODE,
 	},
-	[ALC256_FIXUP_TONGFANG_RESET_PERSISTENT_SETTINGS] = {
+	[ALC256_FIXUP_SET_COEF_DEFAULTS] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc256_fixup_set_coef_defaults,
+	},
+	[ALC245_FIXUP_HP_GPIO_LED] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc245_fixup_hp_gpio_led,
+	},
+	[ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x19, 0x03a11120 }, /* use as headset mic, without its own jack detect */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC,
+	},
+	[ALC233_FIXUP_NO_AUDIO_JACK] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc233_fixup_no_audio_jack,
+	},
+	[ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc256_fixup_mic_no_presence_and_resume,
+		.chained = true,
+		.chain_id = ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC
+	},
+	[ALC287_FIXUP_LEGION_16ACHG6] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc287_fixup_legion_16achg6_speakers,
+	},
+	[ALC287_FIXUP_CS35L41_I2C_2] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cs35l41_fixup_i2c_two,
+		.chained = true,
+		.chain_id = ALC269_FIXUP_THINKPAD_ACPI,
+	},
+	[ALC287_FIXUP_CS35L41_I2C_2_HP_GPIO_LED] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cs35l41_fixup_i2c_two,
+		.chained = true,
+		.chain_id = ALC285_FIXUP_HP_MUTE_LED,
+	},
+	[ALC245_FIXUP_CS35L41_SPI_2] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cs35l41_fixup_spi_two,
+	},
+	[ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cs35l41_fixup_spi_two,
+		.chained = true,
+		.chain_id = ALC285_FIXUP_HP_GPIO_LED,
+	},
+	[ALC245_FIXUP_CS35L41_SPI_4] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cs35l41_fixup_spi_four,
+	},
+	[ALC245_FIXUP_CS35L41_SPI_4_HP_GPIO_LED] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cs35l41_fixup_spi_four,
+		.chained = true,
+		.chain_id = ALC285_FIXUP_HP_GPIO_LED,
+	},
+	[ALC285_FIXUP_HP_SPEAKERS_MICMUTE_LED] = {
+		.type = HDA_FIXUP_VERBS,
+		.v.verbs = (const struct hda_verb[]) {
+			 { 0x20, AC_VERB_SET_COEF_INDEX, 0x19 },
+			 { 0x20, AC_VERB_SET_PROC_COEF, 0x8e11 },
+			 { }
+		},
+		.chained = true,
+		.chain_id = ALC285_FIXUP_HP_MUTE_LED,
+	},
+	[ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS] = {
 		.type = HDA_FIXUP_FUNC,
-		.v.func = alc256_fixup_tongfang_reset_persistent_settings,
+		.v.func = alc295_fixup_dell_inspiron_top_speakers,
+		.chained = true,
+		.chain_id = ALC269_FIXUP_DELL4_MIC_NO_PRESENCE,
+	},
+	[ALC236_FIXUP_DELL_DUAL_CODECS] = {
+		.type = HDA_FIXUP_PINS,
+		.v.func = alc1220_fixup_gb_dual_codecs,
+		.chained = true,
+		.chain_id = ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
+	},
+	[ALC287_FIXUP_THINKPAD_I2S_SPK] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc287_fixup_bind_dacs,
+	},
+	[ALC256_FIXUP_HEADPHONE_AMP_VOL] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc256_decrease_headphone_amp_val,
 	},
 };
 
@@ -8447,6 +9336,7 @@
 	SND_PCI_QUIRK(0x1025, 0x079b, "Acer Aspire V5-573G", ALC282_FIXUP_ASPIRE_V5_PINS),
 	SND_PCI_QUIRK(0x1025, 0x080d, "Acer Aspire V5-122P", ALC269_FIXUP_ASPIRE_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x0840, "Acer Aspire E1", ALC269VB_FIXUP_ASPIRE_E1_COEF),
+	SND_PCI_QUIRK(0x1025, 0x100c, "Acer Aspire E5-574G", ALC255_FIXUP_ACER_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x1025, 0x101c, "Acer Veriton N2510G", ALC269_FIXUP_LIFEBOOK),
 	SND_PCI_QUIRK(0x1025, 0x102b, "Acer Aspire C24-860", ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1065, "Acer Aspire C20-820", ALC269VC_FIXUP_ACER_HEADSET_MIC),
@@ -8456,22 +9346,29 @@
 	SND_PCI_QUIRK(0x1025, 0x110e, "Acer Aspire ES1-432", ALC255_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1166, "Acer Veriton N4640G", ALC269_FIXUP_LIFEBOOK),
 	SND_PCI_QUIRK(0x1025, 0x1167, "Acer Veriton N6640G", ALC269_FIXUP_LIFEBOOK),
+	SND_PCI_QUIRK(0x1025, 0x1177, "Acer Predator G9-593", ALC255_FIXUP_PREDATOR_SUBWOOFER),
+	SND_PCI_QUIRK(0x1025, 0x1178, "Acer Predator G9-593", ALC255_FIXUP_PREDATOR_SUBWOOFER),
 	SND_PCI_QUIRK(0x1025, 0x1246, "Acer Predator Helios 500", ALC299_FIXUP_PREDATOR_SPK),
 	SND_PCI_QUIRK(0x1025, 0x1247, "Acer vCopperbox", ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS),
 	SND_PCI_QUIRK(0x1025, 0x1248, "Acer Veriton N4660G", ALC269VC_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1269, "Acer SWIFT SF314-54", ALC256_FIXUP_ACER_HEADSET_MIC),
+	SND_PCI_QUIRK(0x1025, 0x126a, "Acer Swift SF114-32", ALC256_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x128f, "Acer Veriton Z6860G", ALC286_FIXUP_ACER_AIO_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x1290, "Acer Veriton Z4860G", ALC286_FIXUP_ACER_AIO_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x1291, "Acer Veriton Z4660G", ALC286_FIXUP_ACER_AIO_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x129c, "Acer SWIFT SF314-55", ALC256_FIXUP_ACER_HEADSET_MIC),
+	SND_PCI_QUIRK(0x1025, 0x129d, "Acer SWIFT SF313-51", ALC256_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1300, "Acer SWIFT SF314-56", ALC256_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1308, "Acer Aspire Z24-890", ALC286_FIXUP_ACER_AIO_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x132a, "Acer TravelMate B114-21", ALC233_FIXUP_ACER_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x1330, "Acer TravelMate X514-51T", ALC255_FIXUP_ACER_HEADSET_MIC),
+	SND_PCI_QUIRK(0x1025, 0x141f, "Acer Spin SP513-54N", ALC255_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x142b, "Acer Swift SF314-42", ALC255_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1430, "Acer TravelMate B311R-31", ALC256_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1025, 0x1466, "Acer Aspire A515-56", ALC255_FIXUP_ACER_HEADPHONE_AND_MIC),
+	SND_PCI_QUIRK(0x1025, 0x1534, "Acer Predator PH315-54", ALC255_FIXUP_ACER_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1028, 0x0470, "Dell M101z", ALC269_FIXUP_DELL_M101Z),
+	SND_PCI_QUIRK(0x1028, 0x053c, "Dell Latitude E5430", ALC292_FIXUP_DELL_E7X),
 	SND_PCI_QUIRK(0x1028, 0x054b, "Dell XPS one 2710", ALC275_FIXUP_DELL_XPS),
 	SND_PCI_QUIRK(0x1028, 0x05bd, "Dell Latitude E6440", ALC292_FIXUP_DELL_E7X),
 	SND_PCI_QUIRK(0x1028, 0x05be, "Dell Latitude E6540", ALC292_FIXUP_DELL_E7X),
@@ -8526,6 +9423,17 @@
 	SND_PCI_QUIRK(0x1028, 0x0a62, "Dell Precision 5560", ALC289_FIXUP_DUAL_SPK),
 	SND_PCI_QUIRK(0x1028, 0x0a9d, "Dell Latitude 5430", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1028, 0x0a9e, "Dell Latitude 5430", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1028, 0x0b19, "Dell XPS 15 9520", ALC289_FIXUP_DUAL_SPK),
+	SND_PCI_QUIRK(0x1028, 0x0b1a, "Dell Precision 5570", ALC289_FIXUP_DUAL_SPK),
+	SND_PCI_QUIRK(0x1028, 0x0b37, "Dell Inspiron 16 Plus 7620 2-in-1", ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS),
+	SND_PCI_QUIRK(0x1028, 0x0b71, "Dell Inspiron 16 Plus 7620", ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS),
+	SND_PCI_QUIRK(0x1028, 0x0c03, "Dell Precision 5340", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1028, 0x0c19, "Dell Precision 3340", ALC236_FIXUP_DELL_DUAL_CODECS),
+	SND_PCI_QUIRK(0x1028, 0x0c1a, "Dell Precision 3340", ALC236_FIXUP_DELL_DUAL_CODECS),
+	SND_PCI_QUIRK(0x1028, 0x0c1b, "Dell Precision 3440", ALC236_FIXUP_DELL_DUAL_CODECS),
+	SND_PCI_QUIRK(0x1028, 0x0c1c, "Dell Precision 3540", ALC236_FIXUP_DELL_DUAL_CODECS),
+	SND_PCI_QUIRK(0x1028, 0x0c1d, "Dell Precision 3440", ALC236_FIXUP_DELL_DUAL_CODECS),
+	SND_PCI_QUIRK(0x1028, 0x0c1e, "Dell Precision 3540", ALC236_FIXUP_DELL_DUAL_CODECS),
 	SND_PCI_QUIRK(0x1028, 0x164a, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1028, 0x164b, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x1586, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC2),
@@ -8585,11 +9493,12 @@
 	SND_PCI_QUIRK(0x103c, 0x2335, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1),
 	SND_PCI_QUIRK(0x103c, 0x2336, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1),
 	SND_PCI_QUIRK(0x103c, 0x2337, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1),
+	SND_PCI_QUIRK(0x103c, 0x2b5e, "HP 288 Pro G2 MT", ALC221_FIXUP_HP_288PRO_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x802e, "HP Z240 SFF", ALC221_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x802f, "HP Z240", ALC221_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x8077, "HP", ALC256_FIXUP_HP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x103c, 0x8158, "HP", ALC256_FIXUP_HP_HEADSET_MIC),
-	SND_PCI_QUIRK(0x103c, 0x820d, "HP Pavilion 15", ALC269_FIXUP_HP_MUTE_LED_MIC3),
+	SND_PCI_QUIRK(0x103c, 0x820d, "HP Pavilion 15", ALC295_FIXUP_HP_X360),
 	SND_PCI_QUIRK(0x103c, 0x8256, "HP", ALC221_FIXUP_HP_FRONT_MIC),
 	SND_PCI_QUIRK(0x103c, 0x827e, "HP x360", ALC295_FIXUP_HP_X360),
 	SND_PCI_QUIRK(0x103c, 0x827f, "HP x360", ALC269_FIXUP_HP_MUTE_LED_MIC3),
@@ -8598,17 +9507,29 @@
 	SND_PCI_QUIRK(0x103c, 0x83b9, "HP Spectre x360", ALC269_FIXUP_HP_MUTE_LED_MIC3),
 	SND_PCI_QUIRK(0x103c, 0x841c, "HP Pavilion 15-CK0xx", ALC269_FIXUP_HP_MUTE_LED_MIC3),
 	SND_PCI_QUIRK(0x103c, 0x8497, "HP Envy x360", ALC269_FIXUP_HP_MUTE_LED_MIC3),
+	SND_PCI_QUIRK(0x103c, 0x84a6, "HP 250 G7 Notebook PC", ALC269_FIXUP_HP_LINE1_MIC1_LED),
+	SND_PCI_QUIRK(0x103c, 0x84ae, "HP 15-db0403ng", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
 	SND_PCI_QUIRK(0x103c, 0x84da, "HP OMEN dc0019-ur", ALC295_FIXUP_HP_OMEN),
 	SND_PCI_QUIRK(0x103c, 0x84e7, "HP Pavilion 15", ALC269_FIXUP_HP_MUTE_LED_MIC3),
 	SND_PCI_QUIRK(0x103c, 0x8519, "HP Spectre x360 15-df0xxx", ALC285_FIXUP_HP_SPECTRE_X360),
+	SND_PCI_QUIRK(0x103c, 0x8537, "HP ProBook 440 G6", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
+	SND_PCI_QUIRK(0x103c, 0x85c6, "HP Pavilion x360 Convertible 14-dy1xxx", ALC295_FIXUP_HP_MUTE_LED_COEFBIT11),
+	SND_PCI_QUIRK(0x103c, 0x85de, "HP Envy x360 13-ar0xxx", ALC285_FIXUP_HP_ENVY_X360),
+	SND_PCI_QUIRK(0x103c, 0x860f, "HP ZBook 15 G6", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x861f, "HP Elite Dragonfly G1", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x869d, "HP", ALC236_FIXUP_HP_MUTE_LED),
+	SND_PCI_QUIRK(0x103c, 0x86c1, "HP Laptop 15-da3001TU", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
 	SND_PCI_QUIRK(0x103c, 0x86c7, "HP Envy AiO 32", ALC274_FIXUP_HP_ENVY_GPIO),
+	SND_PCI_QUIRK(0x103c, 0x86e7, "HP Spectre x360 15-eb0xxx", ALC285_FIXUP_HP_SPECTRE_X360_EB1),
+	SND_PCI_QUIRK(0x103c, 0x86e8, "HP Spectre x360 15-eb0xxx", ALC285_FIXUP_HP_SPECTRE_X360_EB1),
+	SND_PCI_QUIRK(0x103c, 0x86f9, "HP Spectre x360 13-aw0xxx", ALC285_FIXUP_HP_SPECTRE_X360_MUTE_LED),
 	SND_PCI_QUIRK(0x103c, 0x8716, "HP Elite Dragonfly G2 Notebook PC", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x8720, "HP EliteBook x360 1040 G8 Notebook PC", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x8724, "HP EliteBook 850 G7", ALC285_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8728, "HP EliteBook 840 G7", ALC285_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x8729, "HP", ALC285_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x8730, "HP ProBook 445 G7", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
+	SND_PCI_QUIRK(0x103c, 0x8735, "HP ProBook 435 G7", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
 	SND_PCI_QUIRK(0x103c, 0x8736, "HP", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x8760, "HP", ALC285_FIXUP_HP_MUTE_LED),
 	SND_PCI_QUIRK(0x103c, 0x877a, "HP", ALC285_FIXUP_HP_MUTE_LED),
@@ -8617,7 +9538,13 @@
 		      ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x8783, "HP ZBook Fury 15 G7 Mobile Workstation",
 		      ALC285_FIXUP_HP_GPIO_AMP_INIT),
+	SND_PCI_QUIRK(0x103c, 0x8786, "HP OMEN 15", ALC285_FIXUP_HP_MUTE_LED),
+	SND_PCI_QUIRK(0x103c, 0x8787, "HP OMEN 15", ALC285_FIXUP_HP_MUTE_LED),
+	SND_PCI_QUIRK(0x103c, 0x8788, "HP OMEN 15", ALC285_FIXUP_HP_MUTE_LED),
+	SND_PCI_QUIRK(0x103c, 0x87b7, "HP Laptop 14-fq0xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
 	SND_PCI_QUIRK(0x103c, 0x87c8, "HP", ALC287_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x87d3, "HP Laptop 15-gw0xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
+	SND_PCI_QUIRK(0x103c, 0x87df, "HP ProBook 430 G8 Notebook PC", ALC236_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x87e5, "HP ProBook 440 G8 Notebook PC", ALC236_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x87e7, "HP ProBook 450 G8 Notebook PC", ALC236_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x87f1, "HP ProBook 630 G8 Notebook PC", ALC236_FIXUP_HP_GPIO_LED),
@@ -8626,10 +9553,14 @@
 	SND_PCI_QUIRK(0x103c, 0x87f5, "HP", ALC287_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x87f6, "HP Spectre x360 14", ALC245_FIXUP_HP_X360_AMP),
 	SND_PCI_QUIRK(0x103c, 0x87f7, "HP Spectre x360 14", ALC245_FIXUP_HP_X360_AMP),
+	SND_PCI_QUIRK(0x103c, 0x87fd, "HP Laptop 14-dq2xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
+	SND_PCI_QUIRK(0x103c, 0x87fe, "HP Laptop 15s-fq2xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
 	SND_PCI_QUIRK(0x103c, 0x8805, "HP ProBook 650 G8 Notebook PC", ALC236_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x880d, "HP EliteBook 830 G8 Notebook PC", ALC285_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x8811, "HP Spectre x360 15-eb1xxx", ALC285_FIXUP_HP_SPECTRE_X360_EB1),
 	SND_PCI_QUIRK(0x103c, 0x8812, "HP Spectre x360 15-eb1xxx", ALC285_FIXUP_HP_SPECTRE_X360_EB1),
+	SND_PCI_QUIRK(0x103c, 0x881d, "HP 250 G8 Notebook PC", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
+	SND_PCI_QUIRK(0x103c, 0x881e, "HP Laptop 15s-du3xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
 	SND_PCI_QUIRK(0x103c, 0x8846, "HP EliteBook 850 G8 Notebook PC", ALC285_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x8847, "HP EliteBook x360 830 G8 Notebook PC", ALC285_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x103c, 0x884b, "HP EliteBook 840 Aero G8 Notebook PC", ALC285_FIXUP_HP_GPIO_LED),
@@ -8639,16 +9570,49 @@
 	SND_PCI_QUIRK(0x103c, 0x886d, "HP ZBook Fury 17.3 Inch G8 Mobile Workstation PC", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x8870, "HP ZBook Fury 15.6 Inch G8 Mobile Workstation PC", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x8873, "HP ZBook Studio 15.6 Inch G8 Mobile Workstation PC", ALC285_FIXUP_HP_GPIO_AMP_INIT),
+	SND_PCI_QUIRK(0x103c, 0x887a, "HP Laptop 15s-eq2xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2),
 	SND_PCI_QUIRK(0x103c, 0x888d, "HP ZBook Power 15.6 inch G8 Mobile Workstation PC", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8895, "HP EliteBook 855 G8 Notebook PC", ALC285_FIXUP_HP_SPEAKERS_MICMUTE_LED),
 	SND_PCI_QUIRK(0x103c, 0x8896, "HP EliteBook 855 G8 Notebook PC", ALC285_FIXUP_HP_MUTE_LED),
 	SND_PCI_QUIRK(0x103c, 0x8898, "HP EliteBook 845 G8 Notebook PC", ALC285_FIXUP_HP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x103c, 0x88d0, "HP Pavilion 15-eh1xxx (mainboard 88D0)", ALC287_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x896e, "HP EliteBook x360 830 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8971, "HP EliteBook 830 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8972, "HP EliteBook 840 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8973, "HP EliteBook 860 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8974, "HP EliteBook 840 Aero G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8975, "HP EliteBook x360 840 Aero G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8981, "HP Elite Dragonfly G3", ALC245_FIXUP_CS35L41_SPI_4),
+	SND_PCI_QUIRK(0x103c, 0x898e, "HP EliteBook 835 G9", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x103c, 0x898f, "HP EliteBook 835 G9", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x103c, 0x8991, "HP EliteBook 845 G9", ALC287_FIXUP_CS35L41_I2C_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8992, "HP EliteBook 845 G9", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x103c, 0x8994, "HP EliteBook 855 G9", ALC287_FIXUP_CS35L41_I2C_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8995, "HP EliteBook 855 G9", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x103c, 0x89a4, "HP ProBook 440 G9", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89a6, "HP ProBook 450 G9", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89aa, "HP EliteBook 630 G9", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89ac, "HP EliteBook 640 G9", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89ae, "HP EliteBook 650 G9", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89c3, "Zbook Studio G9", ALC245_FIXUP_CS35L41_SPI_4_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89c6, "Zbook Fury 17 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x89ca, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
+	SND_PCI_QUIRK(0x103c, 0x89d3, "HP EliteBook 645 G9 (MB 89D2)", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
+	SND_PCI_QUIRK(0x103c, 0x8a78, "HP Dev One", ALC285_FIXUP_HP_LIMIT_INT_MIC_BOOST),
+	SND_PCI_QUIRK(0x103c, 0x8aa0, "HP ProBook 440 G9 (MB 8A9E)", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8aa3, "HP ProBook 450 G9 (MB 8AA1)", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8aa8, "HP EliteBook 640 G9 (MB 8AA6)", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8aab, "HP EliteBook 650 G9 (MB 8AA9)", ALC236_FIXUP_HP_GPIO_LED),
+	SND_PCI_QUIRK(0x103c, 0x8b5d, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
+	SND_PCI_QUIRK(0x103c, 0x8b5e, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF),
+	SND_PCI_QUIRK(0x103c, 0x8bf0, "HP", ALC236_FIXUP_HP_GPIO_LED),
 	SND_PCI_QUIRK(0x1043, 0x103e, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC),
 	SND_PCI_QUIRK(0x1043, 0x103f, "ASUS TX300", ALC282_FIXUP_ASUS_TX300),
 	SND_PCI_QUIRK(0x1043, 0x106d, "Asus K53BE", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x1043, 0x10a1, "ASUS UX391UA", ALC294_FIXUP_ASUS_SPK),
 	SND_PCI_QUIRK(0x1043, 0x10c0, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC),
 	SND_PCI_QUIRK(0x1043, 0x10d0, "ASUS X540LA/X540LJ", ALC255_FIXUP_ASUS_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1043, 0x10d3, "ASUS K6500ZC", ALC294_FIXUP_ASUS_SPK),
 	SND_PCI_QUIRK(0x1043, 0x115d, "Asus 1015E", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x1043, 0x11c0, "ASUS X556UR", ALC255_FIXUP_ASUS_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1043, 0x125e, "ASUS Q524UQK", ALC255_FIXUP_ASUS_MIC_NO_PRESENCE),
@@ -8657,17 +9621,20 @@
 	SND_PCI_QUIRK(0x1043, 0x12a0, "ASUS X441UV", ALC233_FIXUP_EAPD_COEF_AND_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1043, 0x12e0, "ASUS X541SA", ALC256_FIXUP_ASUS_MIC),
 	SND_PCI_QUIRK(0x1043, 0x12f0, "ASUS X541UV", ALC256_FIXUP_ASUS_MIC),
+	SND_PCI_QUIRK(0x1043, 0x1313, "Asus K42JZ", ALC269VB_FIXUP_ASUS_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1043, 0x13b0, "ASUS Z550SA", ALC256_FIXUP_ASUS_MIC),
 	SND_PCI_QUIRK(0x1043, 0x1427, "Asus Zenbook UX31E", ALC269VB_FIXUP_ASUS_ZENBOOK),
 	SND_PCI_QUIRK(0x1043, 0x1517, "Asus Zenbook UX31A", ALC269VB_FIXUP_ASUS_ZENBOOK_UX31A),
+	SND_PCI_QUIRK(0x1043, 0x1662, "ASUS GV301QH", ALC294_FIXUP_ASUS_DUAL_SPK),
+	SND_PCI_QUIRK(0x1043, 0x16b2, "ASUS GU603", ALC289_FIXUP_ASUS_GA401),
 	SND_PCI_QUIRK(0x1043, 0x16e3, "ASUS UX50", ALC269_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK(0x1043, 0x1740, "ASUS UX430UA", ALC295_FIXUP_ASUS_DACS),
 	SND_PCI_QUIRK(0x1043, 0x17d1, "ASUS UX431FL", ALC294_FIXUP_ASUS_DUAL_SPK),
-	SND_PCI_QUIRK(0x1043, 0x1662, "ASUS GV301QH", ALC294_FIXUP_ASUS_DUAL_SPK),
 	SND_PCI_QUIRK(0x1043, 0x1881, "ASUS Zephyrus S/M", ALC294_FIXUP_ASUS_GX502_PINS),
 	SND_PCI_QUIRK(0x1043, 0x18b1, "Asus MJ401TA", ALC256_FIXUP_ASUS_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1043, 0x18f1, "Asus FX505DT", ALC256_FIXUP_ASUS_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1043, 0x194e, "ASUS UX563FD", ALC294_FIXUP_ASUS_HPE),
+	SND_PCI_QUIRK(0x1043, 0x1970, "ASUS UX550VE", ALC289_FIXUP_ASUS_GA401),
 	SND_PCI_QUIRK(0x1043, 0x1982, "ASUS B1400CEPE", ALC256_FIXUP_ASUS_HPE),
 	SND_PCI_QUIRK(0x1043, 0x19ce, "ASUS B9450FA", ALC294_FIXUP_ASUS_HPE),
 	SND_PCI_QUIRK(0x1043, 0x19e1, "ASUS UX581LV", ALC295_FIXUP_ASUS_MIC_NO_PRESENCE),
@@ -8677,12 +9644,18 @@
 	SND_PCI_QUIRK(0x1043, 0x1b13, "Asus U41SV", ALC269_FIXUP_INV_DMIC),
 	SND_PCI_QUIRK(0x1043, 0x1bbd, "ASUS Z550MA", ALC255_FIXUP_ASUS_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1043, 0x1c23, "Asus X55U", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
+	SND_PCI_QUIRK(0x1043, 0x1c62, "ASUS GU603", ALC289_FIXUP_ASUS_GA401),
+	SND_PCI_QUIRK(0x1043, 0x1c92, "ASUS ROG Strix G15", ALC285_FIXUP_ASUS_G533Z_PINS),
 	SND_PCI_QUIRK(0x1043, 0x1ccd, "ASUS X555UB", ALC256_FIXUP_ASUS_MIC),
+	SND_PCI_QUIRK(0x1043, 0x1d42, "ASUS Zephyrus G14 2022", ALC289_FIXUP_ASUS_GA401),
 	SND_PCI_QUIRK(0x1043, 0x1d4e, "ASUS TM420", ALC256_FIXUP_ASUS_HPE),
 	SND_PCI_QUIRK(0x1043, 0x1e11, "ASUS Zephyrus G15", ALC289_FIXUP_ASUS_GA502),
 	SND_PCI_QUIRK(0x1043, 0x1e51, "ASUS Zephyrus M15", ALC294_FIXUP_ASUS_GU502_PINS),
+	SND_PCI_QUIRK(0x1043, 0x1e5e, "ASUS ROG Strix G513", ALC294_FIXUP_ASUS_G513_PINS),
 	SND_PCI_QUIRK(0x1043, 0x1e8e, "ASUS Zephyrus G15", ALC289_FIXUP_ASUS_GA401),
+	SND_PCI_QUIRK(0x1043, 0x1c52, "ASUS Zephyrus G15 2022", ALC289_FIXUP_ASUS_GA401),
 	SND_PCI_QUIRK(0x1043, 0x1f11, "ASUS Zephyrus G14", ALC289_FIXUP_ASUS_GA401),
+	SND_PCI_QUIRK(0x1043, 0x1f92, "ASUS ROG Flow X16", ALC289_FIXUP_ASUS_GA401),
 	SND_PCI_QUIRK(0x1043, 0x3030, "ASUS ZN270IE", ALC256_FIXUP_ASUS_AIO_GPIO2),
 	SND_PCI_QUIRK(0x1043, 0x831a, "ASUS P901", ALC269_FIXUP_STEREO_DMIC),
 	SND_PCI_QUIRK(0x1043, 0x834a, "ASUS S101", ALC269_FIXUP_STEREO_DMIC),
@@ -8703,18 +9676,28 @@
 	SND_PCI_QUIRK(0x10cf, 0x1845, "Lifebook U904", ALC269_FIXUP_LIFEBOOK_EXTMIC),
 	SND_PCI_QUIRK(0x10ec, 0x10f2, "Intel Reference board", ALC700_FIXUP_INTEL_REFERENCE),
 	SND_PCI_QUIRK(0x10ec, 0x118c, "Medion EE4254 MD62100", ALC256_FIXUP_MEDION_HEADSET_NO_PRESENCE),
+	SND_PCI_QUIRK(0x10ec, 0x119e, "Positivo SU C1400", ALC269_FIXUP_ASPIRE_HEADSET_MIC),
+	SND_PCI_QUIRK(0x10ec, 0x11bc, "VAIO VJFE-IL", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x10ec, 0x1230, "Intel Reference board", ALC295_FIXUP_CHROME_BOOK),
+	SND_PCI_QUIRK(0x10ec, 0x124c, "Intel Reference board", ALC295_FIXUP_CHROME_BOOK),
 	SND_PCI_QUIRK(0x10ec, 0x1252, "Intel Reference board", ALC295_FIXUP_CHROME_BOOK),
 	SND_PCI_QUIRK(0x10ec, 0x1254, "Intel Reference board", ALC295_FIXUP_CHROME_BOOK),
-	SND_PCI_QUIRK(0x10f7, 0x8338, "Panasonic CF-SZ6", ALC269_FIXUP_HEADSET_MODE),
+	SND_PCI_QUIRK(0x10f7, 0x8338, "Panasonic CF-SZ6", ALC269_FIXUP_ASPIRE_HEADSET_MIC),
 	SND_PCI_QUIRK(0x144d, 0xc109, "Samsung Ativ book 9 (NP900X3G)", ALC269_FIXUP_INV_DMIC),
-	SND_PCI_QUIRK(0x144d, 0xc169, "Samsung Notebook 9 Pen (NP930SBE-K01US)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
-	SND_PCI_QUIRK(0x144d, 0xc176, "Samsung Notebook 9 Pro (NP930MBE-K04US)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
-	SND_PCI_QUIRK(0x144d, 0xc189, "Samsung Galaxy Flex Book (NT950QCG-X716)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
-	SND_PCI_QUIRK(0x144d, 0xc18a, "Samsung Galaxy Book Ion (NP930XCJ-K01US)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
+	SND_PCI_QUIRK(0x144d, 0xc169, "Samsung Notebook 9 Pen (NP930SBE-K01US)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc176, "Samsung Notebook 9 Pro (NP930MBE-K04US)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc189, "Samsung Galaxy Flex Book (NT950QCG-X716)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc18a, "Samsung Galaxy Book Ion (NP930XCJ-K01US)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc1a3, "Samsung Galaxy Book Pro (NP935XDB-KC1SE)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc1a4, "Samsung Galaxy Book Pro 360 (NT935QBD)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc1a6, "Samsung Galaxy Book Pro 360 (NP930QBD)", ALC298_FIXUP_SAMSUNG_AMP),
 	SND_PCI_QUIRK(0x144d, 0xc740, "Samsung Ativ book 8 (NP870Z5G)", ALC269_FIXUP_ATIV_BOOK_8),
-	SND_PCI_QUIRK(0x144d, 0xc812, "Samsung Notebook Pen S (NT950SBE-X58)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
-	SND_PCI_QUIRK(0x144d, 0xc830, "Samsung Galaxy Book Ion (NT950XCJ-X716A)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
+	SND_PCI_QUIRK(0x144d, 0xc812, "Samsung Notebook Pen S (NT950SBE-X58)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc830, "Samsung Galaxy Book Ion (NT950XCJ-X716A)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xc832, "Samsung Galaxy Book Flex Alpha (NP730QCJ)", ALC256_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
+	SND_PCI_QUIRK(0x144d, 0xca03, "Samsung Galaxy Book2 Pro 360 (NP930QED)", ALC298_FIXUP_SAMSUNG_AMP),
+	SND_PCI_QUIRK(0x144d, 0xca06, "Samsung Galaxy Book3 360 (NP730QFG)", ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET),
+	SND_PCI_QUIRK(0x144d, 0xc868, "Samsung Galaxy Book2 Pro (NP930XED)", ALC298_FIXUP_SAMSUNG_AMP),
 	SND_PCI_QUIRK(0x1458, 0xfa53, "Gigabyte BXBT-2807", ALC283_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1462, 0xb120, "MSI Cubi MS-B120", ALC283_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1462, 0xb171, "Cubi N 8GL (MS-B171)", ALC283_FIXUP_HEADSET_MIC),
@@ -8728,14 +9711,19 @@
 	SND_PCI_QUIRK(0x1558, 0x4018, "Clevo NV40M[BE]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x4019, "Clevo NV40MZ", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x4020, "Clevo NV40MB", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x4041, "Clevo NV4[15]PZ", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x40a1, "Clevo NL40GU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x40c1, "Clevo NL40[CZ]U", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x40d1, "Clevo NL41DU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x5015, "Clevo NH5[58]H[HJK]Q", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x5017, "Clevo NH7[79]H[HJK]Q", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50a3, "Clevo NJ51GU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50b3, "Clevo NK50S[BEZ]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50b6, "Clevo NK50S5", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50b8, "Clevo NK50SZ", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50d5, "Clevo NP50D5", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x50e1, "Clevo NH5[58]HPQ", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x50e2, "Clevo NH7[79]HPQ", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50f0, "Clevo NH50A[CDF]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50f2, "Clevo NH50E[PR]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x50f3, "Clevo NH58DPQ", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
@@ -8744,12 +9732,19 @@
 	SND_PCI_QUIRK(0x1558, 0x5101, "Clevo S510WU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x5157, "Clevo W517GU1", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x51a1, "Clevo NS50MU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x51b1, "Clevo NS50AU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x51b3, "Clevo NS70AU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x5630, "Clevo NP50RNJS", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x70a1, "Clevo NB70T[HJK]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x70b3, "Clevo NK70SB", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x70f2, "Clevo NH79EPY", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x70f3, "Clevo NH77DPQ", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x70f4, "Clevo NH77EPY", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x70f6, "Clevo NH77DPQ-Y", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x7716, "Clevo NS50PU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x7717, "Clevo NS70PU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x7718, "Clevo L140PU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x7724, "Clevo L140AU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x8228, "Clevo NR40BU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x8520, "Clevo NH50D[CD]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x8521, "Clevo NH77D[CD]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
@@ -8761,8 +9756,11 @@
 	SND_PCI_QUIRK(0x1558, 0x8561, "Clevo NH[57][0-9][ER][ACDH]Q", ALC269_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1558, 0x8562, "Clevo NH[57][0-9]RZ[Q]", ALC269_FIXUP_DMIC),
 	SND_PCI_QUIRK(0x1558, 0x8668, "Clevo NP50B[BE]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x866d, "Clevo NP5[05]PN[HJK]", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x867c, "Clevo NP7[01]PNP", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x867d, "Clevo NP7[01]PN[HJK]", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x8680, "Clevo NJ50LU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
-	SND_PCI_QUIRK(0x1558, 0x8686, "Clevo NH50[CZ]U", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0x8686, "Clevo NH50[CZ]U", ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME),
 	SND_PCI_QUIRK(0x1558, 0x8a20, "Clevo NH55DCQ-Y", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x8a51, "Clevo NH70RCQ-Y", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0x8d50, "Clevo NH55RCQ-M", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
@@ -8772,6 +9770,9 @@
 	SND_PCI_QUIRK(0x1558, 0x971d, "Clevo N970T[CDF]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0xa500, "Clevo NL5[03]RU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0xa600, "Clevo NL50NU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0xa650, "Clevo NP[567]0SN[CD]", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0xa671, "Clevo NP70SN[CDE]", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1558, 0xa763, "Clevo V54x_6x_TU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0xb018, "Clevo NP50D[BE]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0xb019, "Clevo NH77D[BE]Q", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1558, 0xb022, "Clevo NH77D[DC][QW]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE),
@@ -8817,6 +9818,14 @@
 	SND_PCI_QUIRK(0x17aa, 0x22be, "Thinkpad X1 Carbon 8th", ALC285_FIXUP_THINKPAD_HEADSET_JACK),
 	SND_PCI_QUIRK(0x17aa, 0x22c1, "Thinkpad P1 Gen 3", ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK),
 	SND_PCI_QUIRK(0x17aa, 0x22c2, "Thinkpad X1 Extreme Gen 3", ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK),
+	SND_PCI_QUIRK(0x17aa, 0x22f1, "Thinkpad", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x22f2, "Thinkpad", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x22f3, "Thinkpad", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x2316, "Thinkpad P1 Gen 6", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x2317, "Thinkpad P1 Gen 6", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x2318, "Thinkpad Z13 Gen2", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x2319, "Thinkpad Z16 Gen2", ALC287_FIXUP_CS35L41_I2C_2),
+	SND_PCI_QUIRK(0x17aa, 0x231a, "Thinkpad Z16 Gen2", ALC287_FIXUP_CS35L41_I2C_2),
 	SND_PCI_QUIRK(0x17aa, 0x30bb, "ThinkCentre AIO", ALC233_FIXUP_LENOVO_LINE2_MIC_HOTKEY),
 	SND_PCI_QUIRK(0x17aa, 0x30e2, "ThinkCentre AIO", ALC233_FIXUP_LENOVO_LINE2_MIC_HOTKEY),
 	SND_PCI_QUIRK(0x17aa, 0x310c, "ThinkCentre Station", ALC294_FIXUP_LENOVO_MIC_LOCATION),
@@ -8828,14 +9837,22 @@
 	SND_PCI_QUIRK(0x17aa, 0x3176, "ThinkCentre Station", ALC283_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x17aa, 0x3178, "ThinkCentre Station", ALC283_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x17aa, 0x31af, "ThinkCentre Station", ALC623_FIXUP_LENOVO_THINKSTATION_P340),
-	SND_PCI_QUIRK(0x17aa, 0x3818, "Lenovo C940", ALC298_FIXUP_LENOVO_SPK_VOLUME),
+	SND_PCI_QUIRK(0x17aa, 0x3802, "Lenovo Yoga DuetITL 2021", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS),
+	SND_PCI_QUIRK(0x17aa, 0x3813, "Legion 7i 15IMHG05", ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS),
+	SND_PCI_QUIRK(0x17aa, 0x3818, "Lenovo C940 / Yoga Duet 7", ALC298_FIXUP_LENOVO_C940_DUET7),
+	SND_PCI_QUIRK(0x17aa, 0x3819, "Lenovo 13s Gen2 ITL", ALC287_FIXUP_13S_GEN2_SPEAKERS),
+	SND_PCI_QUIRK(0x17aa, 0x3820, "Yoga Duet 7 13ITL6", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS),
+	SND_PCI_QUIRK(0x17aa, 0x3824, "Legion Y9000X 2020", ALC285_FIXUP_LEGION_Y9000X_SPEAKERS),
 	SND_PCI_QUIRK(0x17aa, 0x3827, "Ideapad S740", ALC285_FIXUP_IDEAPAD_S740_COEF),
+	SND_PCI_QUIRK(0x17aa, 0x3834, "Lenovo IdeaPad Slim 9i 14ITL5", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS),
+	SND_PCI_QUIRK(0x17aa, 0x383d, "Legion Y9000X 2019", ALC285_FIXUP_LEGION_Y9000X_SPEAKERS),
 	SND_PCI_QUIRK(0x17aa, 0x3843, "Yoga 9i", ALC287_FIXUP_IDEAPAD_BASS_SPK_AMP),
-	SND_PCI_QUIRK(0x17aa, 0x3813, "Legion 7i 15IMHG05", ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS),
+	SND_PCI_QUIRK(0x17aa, 0x3847, "Legion 7 16ACHG6", ALC287_FIXUP_LEGION_16ACHG6),
+	SND_PCI_QUIRK(0x17aa, 0x384a, "Lenovo Yoga 7 15ITL5", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS),
 	SND_PCI_QUIRK(0x17aa, 0x3852, "Lenovo Yoga 7 14ITL5", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS),
 	SND_PCI_QUIRK(0x17aa, 0x3853, "Lenovo Yoga 7 15ITL5", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS),
-	SND_PCI_QUIRK(0x17aa, 0x3819, "Lenovo 13s Gen2 ITL", ALC287_FIXUP_13S_GEN2_SPEAKERS),
 	SND_PCI_QUIRK(0x17aa, 0x3902, "Lenovo E50-80", ALC269_FIXUP_DMIC_THINKPAD_ACPI),
+	SND_PCI_QUIRK(0x17aa, 0x3913, "Lenovo 145", ALC236_FIXUP_LENOVO_INV_DMIC),
 	SND_PCI_QUIRK(0x17aa, 0x3977, "IdeaPad S210", ALC283_FIXUP_INT_MIC),
 	SND_PCI_QUIRK(0x17aa, 0x3978, "Lenovo B50-70", ALC269_FIXUP_DMIC_THINKPAD_ACPI),
 	SND_PCI_QUIRK(0x17aa, 0x3bf8, "Quanta FL1", ALC269_FIXUP_PCM_44K),
@@ -8854,22 +9871,48 @@
 	SND_PCI_QUIRK(0x17aa, 0x505d, "Thinkpad", ALC298_FIXUP_TPT470_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x505f, "Thinkpad", ALC298_FIXUP_TPT470_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x5062, "Thinkpad", ALC298_FIXUP_TPT470_DOCK),
+	SND_PCI_QUIRK(0x17aa, 0x508b, "Thinkpad X12 Gen 1", ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS),
 	SND_PCI_QUIRK(0x17aa, 0x5109, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x17aa, 0x511e, "Thinkpad", ALC298_FIXUP_TPT470_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x511f, "Thinkpad", ALC298_FIXUP_TPT470_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x9e54, "LENOVO NB", ALC269_FIXUP_LENOVO_EAPD),
+	SND_PCI_QUIRK(0x17aa, 0x9e56, "Lenovo ZhaoYang CF4620Z", ALC286_FIXUP_SONY_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1849, 0x0269, "Positivo Master C6400", ALC269VB_FIXUP_ASUS_ZENBOOK),
+	SND_PCI_QUIRK(0x1849, 0x1233, "ASRock NUC Box 1100", ALC233_FIXUP_NO_AUDIO_JACK),
+	SND_PCI_QUIRK(0x1849, 0xa233, "Positivo Master C6300", ALC269_FIXUP_HEADSET_MIC),
+	SND_PCI_QUIRK(0x1854, 0x0440, "LG CQ6", ALC256_FIXUP_HEADPHONE_AMP_VOL),
+	SND_PCI_QUIRK(0x1854, 0x0441, "LG CQ6 AIO", ALC256_FIXUP_HEADPHONE_AMP_VOL),
 	SND_PCI_QUIRK(0x19e5, 0x3204, "Huawei MACH-WX9", ALC256_FIXUP_HUAWEI_MACH_WX9_PINS),
+	SND_PCI_QUIRK(0x19e5, 0x320f, "Huawei WRT-WX9 ", ALC256_FIXUP_ASUS_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x19e5, 0x3212, "Huawei KLV-WX9 ", ALC256_FIXUP_ACER_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1b35, 0x1235, "CZC B20", ALC269_FIXUP_CZC_B20),
 	SND_PCI_QUIRK(0x1b35, 0x1236, "CZC TMI", ALC269_FIXUP_CZC_TMI),
 	SND_PCI_QUIRK(0x1b35, 0x1237, "CZC L101", ALC269_FIXUP_CZC_L101),
 	SND_PCI_QUIRK(0x1b7d, 0xa831, "Ordissimo EVE2 ", ALC269VB_FIXUP_ORDISSIMO_EVE2), /* Also known as Malata PC-B1303 */
 	SND_PCI_QUIRK(0x1c06, 0x2013, "Lemote A1802", ALC269_FIXUP_LEMOTE_A1802),
 	SND_PCI_QUIRK(0x1c06, 0x2015, "Lemote A190X", ALC269_FIXUP_LEMOTE_A190X),
-	SND_PCI_QUIRK(0x1d05, 0x1132, "TongFang PHxTxX1", ALC256_FIXUP_TONGFANG_RESET_PERSISTENT_SETTINGS),
+	SND_PCI_QUIRK(0x1c6c, 0x122a, "Positivo N14AP7", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
+	SND_PCI_QUIRK(0x1c6c, 0x1251, "Positivo N14KP6-TG", ALC288_FIXUP_DELL1_MIC_NO_PRESENCE),
+	SND_PCI_QUIRK(0x1d05, 0x1132, "TongFang PHxTxX1", ALC256_FIXUP_SET_COEF_DEFAULTS),
+	SND_PCI_QUIRK(0x1d05, 0x1096, "TongFang GMxMRxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x1100, "TongFang GKxNRxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x1111, "TongFang GMxZGxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x1119, "TongFang GMxZGxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x1129, "TongFang GMxZGxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x1147, "TongFang GMxTGxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x115c, "TongFang GMxTGxx", ALC269_FIXUP_NO_SHUTUP),
+	SND_PCI_QUIRK(0x1d05, 0x121b, "TongFang GMxAGxx", ALC269_FIXUP_NO_SHUTUP),
 	SND_PCI_QUIRK(0x1d72, 0x1602, "RedmiBook", ALC255_FIXUP_XIAOMI_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1d72, 0x1701, "XiaomiNotebook Pro", ALC298_FIXUP_DELL1_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1d72, 0x1901, "RedmiBook 14", ALC256_FIXUP_ASUS_HEADSET_MIC),
+	SND_PCI_QUIRK(0x1d72, 0x1945, "Redmi G", ALC256_FIXUP_ASUS_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1d72, 0x1947, "RedmiBook Air", ALC255_FIXUP_XIAOMI_HEADSET_MIC),
+	SND_PCI_QUIRK(0x2782, 0x0214, "VAIO VJFE-CL", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
+	SND_PCI_QUIRK(0x2782, 0x0228, "Infinix ZERO BOOK 13", ALC269VB_FIXUP_INFINIX_ZERO_BOOK_13),
+	SND_PCI_QUIRK(0x2782, 0x0232, "CHUWI CoreBook XPro", ALC269VB_FIXUP_CHUWI_COREBOOK_XPRO),
+	SND_PCI_QUIRK(0x2782, 0x1701, "Infinix Y4 Max", ALC269VC_FIXUP_INFINIX_Y4_MAX),
+	SND_PCI_QUIRK(0x2782, 0x1705, "MEDION E15433", ALC269VC_FIXUP_INFINIX_Y4_MAX),
+	SND_PCI_QUIRK(0x2782, 0x1707, "Vaio VJFE-ADL", ALC298_FIXUP_SPK_VOLUME),
 	SND_PCI_QUIRK(0x8086, 0x2074, "Intel NUC 8", ALC233_FIXUP_INTEL_NUC8_DMIC),
 	SND_PCI_QUIRK(0x8086, 0x2080, "Intel NUC 8 Rugged", ALC256_FIXUP_INTEL_NUC8_RUGGED),
 	SND_PCI_QUIRK(0x8086, 0x2081, "Intel NUC 10", ALC256_FIXUP_INTEL_NUC10),
@@ -9045,16 +10088,20 @@
 	{.id = ALC299_FIXUP_PREDATOR_SPK, .name = "predator-spk"},
 	{.id = ALC298_FIXUP_HUAWEI_MBX_STEREO, .name = "huawei-mbx-stereo"},
 	{.id = ALC256_FIXUP_MEDION_HEADSET_NO_PRESENCE, .name = "alc256-medion-headset"},
-	{.id = ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET, .name = "alc298-samsung-headphone"},
+	{.id = ALC298_FIXUP_SAMSUNG_AMP, .name = "alc298-samsung-amp"},
+	{.id = ALC256_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET, .name = "alc256-samsung-headphone"},
 	{.id = ALC255_FIXUP_XIAOMI_HEADSET_MIC, .name = "alc255-xiaomi-headset"},
 	{.id = ALC274_FIXUP_HP_MIC, .name = "alc274-hp-mic-detect"},
 	{.id = ALC245_FIXUP_HP_X360_AMP, .name = "alc245-hp-x360-amp"},
 	{.id = ALC295_FIXUP_HP_OMEN, .name = "alc295-hp-omen"},
 	{.id = ALC285_FIXUP_HP_SPECTRE_X360, .name = "alc285-hp-spectre-x360"},
 	{.id = ALC285_FIXUP_HP_SPECTRE_X360_EB1, .name = "alc285-hp-spectre-x360-eb1"},
+	{.id = ALC285_FIXUP_HP_ENVY_X360, .name = "alc285-hp-envy-x360"},
 	{.id = ALC287_FIXUP_IDEAPAD_BASS_SPK_AMP, .name = "alc287-ideapad-bass-spk-amp"},
 	{.id = ALC623_FIXUP_LENOVO_THINKSTATION_P340, .name = "alc623-lenovo-thinkstation-p340"},
 	{.id = ALC255_FIXUP_ACER_HEADPHONE_AND_MIC, .name = "alc255-acer-headphone-and-mic"},
+	{.id = ALC285_FIXUP_HP_GPIO_AMP_INIT, .name = "alc285-hp-amp-init"},
+	{.id = ALC236_FIXUP_LENOVO_INV_DMIC, .name = "alc236-fixup-lenovo-inv-mic"},
 	{}
 };
 #define ALC225_STANDARD_PINS \
@@ -9350,6 +10397,10 @@
 		{0x17, 0x90170111},
 		{0x19, 0x03a11030},
 		{0x21, 0x03211020}),
+	SND_HDA_PIN_QUIRK(0x10ec0287, 0x17aa, "Lenovo", ALC287_FIXUP_THINKPAD_I2S_SPK,
+		{0x17, 0x90170110},
+		{0x19, 0x03a11030},
+		{0x21, 0x03211020}),
 	SND_HDA_PIN_QUIRK(0x10ec0286, 0x1025, "Acer", ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE,
 		{0x12, 0x90a60130},
 		{0x17, 0x90170110},
@@ -9444,22 +10495,6 @@
 		{0x12, 0x90a60130},
 		{0x17, 0x90170110},
 		{0x21, 0x03211020}),
-	SND_HDA_PIN_QUIRK(0x10ec0295, 0x1028, "Dell", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE,
-		{0x14, 0x90170110},
-		{0x21, 0x04211020}),
-	SND_HDA_PIN_QUIRK(0x10ec0295, 0x1028, "Dell", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE,
-		{0x14, 0x90170110},
-		{0x21, 0x04211030}),
-	SND_HDA_PIN_QUIRK(0x10ec0295, 0x1028, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE,
-		ALC295_STANDARD_PINS,
-		{0x17, 0x21014020},
-		{0x18, 0x21a19030}),
-	SND_HDA_PIN_QUIRK(0x10ec0295, 0x1028, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE,
-		ALC295_STANDARD_PINS,
-		{0x17, 0x21014040},
-		{0x18, 0x21a19050}),
-	SND_HDA_PIN_QUIRK(0x10ec0295, 0x1028, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE,
-		ALC295_STANDARD_PINS),
 	SND_HDA_PIN_QUIRK(0x10ec0298, 0x1028, "Dell", ALC298_FIXUP_DELL1_MIC_NO_PRESENCE,
 		ALC298_STANDARD_PINS,
 		{0x17, 0x90170110}),
@@ -9503,6 +10538,9 @@
 	SND_HDA_PIN_QUIRK(0x10ec0289, 0x1028, "Dell", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE,
 		{0x19, 0x40000000},
 		{0x1b, 0x40000000}),
+	SND_HDA_PIN_QUIRK(0x10ec0295, 0x1028, "Dell", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE,
+		{0x19, 0x40000000},
+		{0x1b, 0x40000000}),
 	SND_HDA_PIN_QUIRK(0x10ec0256, 0x1028, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
 		{0x19, 0x40000000},
 		{0x1a, 0x40000000}),
@@ -9569,6 +10607,7 @@
 	spec = codec->spec;
 	spec->gen.shared_mic_vref_pin = 0x18;
 	codec->power_save_node = 0;
+	spec->en_3kpull_low = true;
 
 #ifdef CONFIG_PM
 	codec->patch_ops.suspend = alc269_suspend;
@@ -9646,22 +10685,30 @@
 	case 0x10ec0230:
 	case 0x10ec0236:
 	case 0x10ec0256:
+	case 0x19e58326:
 		spec->codec_variant = ALC269_TYPE_ALC256;
 		spec->shutup = alc256_shutup;
 		spec->init_hook = alc256_init;
 		spec->gen.mixer_nid = 0; /* ALC256 does not have any loopback mixer path */
+		if (codec->core.vendor_id == 0x10ec0236 &&
+		    codec->bus->pci->vendor != PCI_VENDOR_ID_AMD)
+			spec->en_3kpull_low = false;
 		break;
 	case 0x10ec0257:
 		spec->codec_variant = ALC269_TYPE_ALC257;
 		spec->shutup = alc256_shutup;
 		spec->init_hook = alc256_init;
 		spec->gen.mixer_nid = 0;
+		spec->en_3kpull_low = false;
 		break;
 	case 0x10ec0215:
 	case 0x10ec0245:
 	case 0x10ec0285:
 	case 0x10ec0289:
-		spec->codec_variant = ALC269_TYPE_ALC215;
+		if (alc_get_coef0(codec) & 0x0010)
+			spec->codec_variant = ALC269_TYPE_ALC245;
+		else
+			spec->codec_variant = ALC269_TYPE_ALC215;
 		spec->shutup = alc225_shutup;
 		spec->init_hook = alc225_init;
 		spec->gen.mixer_nid = 0;
@@ -9692,8 +10739,11 @@
 		spec->codec_variant = ALC269_TYPE_ALC300;
 		spec->gen.mixer_nid = 0; /* no loopback on ALC300 */
 		break;
+	case 0x10ec0222:
 	case 0x10ec0623:
 		spec->codec_variant = ALC269_TYPE_ALC623;
+		spec->shutup = alc222_shutup;
+		spec->init_hook = alc222_init;
 		break;
 	case 0x10ec0700:
 	case 0x10ec0701:
@@ -10167,6 +11217,41 @@
 	}
 }
 
+static void alc897_hp_automute_hook(struct hda_codec *codec,
+					 struct hda_jack_callback *jack)
+{
+	struct alc_spec *spec = codec->spec;
+	int vref;
+
+	snd_hda_gen_hp_automute(codec, jack);
+	vref = spec->gen.hp_jack_present ? (PIN_HP | AC_PINCTL_VREF_100) : PIN_HP;
+	snd_hda_set_pin_ctl(codec, 0x1b, vref);
+}
+
+static void alc897_fixup_lenovo_headset_mic(struct hda_codec *codec,
+				     const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+	if (action == HDA_FIXUP_ACT_PRE_PROBE) {
+		spec->gen.hp_automute_hook = alc897_hp_automute_hook;
+		spec->no_shutup_pins = 1;
+	}
+	if (action == HDA_FIXUP_ACT_PROBE) {
+		snd_hda_set_pin_ctl_cache(codec, 0x1a, PIN_IN | AC_PINCTL_VREF_100);
+	}
+}
+
+static void alc897_fixup_lenovo_headset_mode(struct hda_codec *codec,
+				     const struct hda_fixup *fix, int action)
+{
+	struct alc_spec *spec = codec->spec;
+
+	if (action == HDA_FIXUP_ACT_PRE_PROBE) {
+		spec->parse_flags |= HDA_PINCFG_HEADSET_MIC;
+		spec->gen.hp_automute_hook = alc897_hp_automute_hook;
+	}
+}
+
 static const struct coef_fw alc668_coefs[] = {
 	WRITE_COEF(0x01, 0xbebe), WRITE_COEF(0x02, 0xaaaa), WRITE_COEF(0x03,    0x0),
 	WRITE_COEF(0x04, 0x0180), WRITE_COEF(0x06,    0x0), WRITE_COEF(0x07, 0x0f80),
@@ -10247,6 +11332,13 @@
 	ALC668_FIXUP_ASUS_NO_HEADSET_MIC,
 	ALC668_FIXUP_HEADSET_MIC,
 	ALC668_FIXUP_MIC_DET_COEF,
+	ALC897_FIXUP_LENOVO_HEADSET_MIC,
+	ALC897_FIXUP_HEADSET_MIC_PIN,
+	ALC897_FIXUP_HP_HSMIC_VERB,
+	ALC897_FIXUP_LENOVO_HEADSET_MODE,
+	ALC897_FIXUP_HEADSET_MIC_PIN2,
+	ALC897_FIXUP_UNIS_H3C_X500S,
+	ALC897_FIXUP_HEADSET_MIC_PIN3,
 };
 
 static const struct hda_fixup alc662_fixups[] = {
@@ -10653,10 +11745,58 @@
 			{}
 		},
 	},
+	[ALC897_FIXUP_LENOVO_HEADSET_MIC] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc897_fixup_lenovo_headset_mic,
+	},
+	[ALC897_FIXUP_HEADSET_MIC_PIN] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x1a, 0x03a11050 },
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC897_FIXUP_LENOVO_HEADSET_MIC
+	},
+	[ALC897_FIXUP_HP_HSMIC_VERB] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x19, 0x01a1913c }, /* use as headset mic, without its own jack detect */
+			{ }
+		},
+	},
+	[ALC897_FIXUP_LENOVO_HEADSET_MODE] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc897_fixup_lenovo_headset_mode,
+	},
+	[ALC897_FIXUP_HEADSET_MIC_PIN2] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x1a, 0x01a11140 }, /* use as headset mic, without its own jack detect */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC897_FIXUP_LENOVO_HEADSET_MODE
+	},
+	[ALC897_FIXUP_UNIS_H3C_X500S] = {
+		.type = HDA_FIXUP_VERBS,
+		.v.verbs = (const struct hda_verb[]) {
+			{ 0x14, AC_VERB_SET_EAPD_BTLENABLE, 0 },
+			{}
+		},
+	},
+	[ALC897_FIXUP_HEADSET_MIC_PIN3] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x19, 0x03a11050 }, /* use as headset mic */
+			{ }
+		},
+	},
 };
 
 static const struct snd_pci_quirk alc662_fixup_tbl[] = {
 	SND_PCI_QUIRK(0x1019, 0x9087, "ECS", ALC662_FIXUP_ASUS_MODE2),
+	SND_PCI_QUIRK(0x1019, 0x9859, "JP-IK LEAP W502", ALC897_FIXUP_HEADSET_MIC_PIN3),
 	SND_PCI_QUIRK(0x1025, 0x022f, "Acer Aspire One", ALC662_FIXUP_INV_DMIC),
 	SND_PCI_QUIRK(0x1025, 0x0241, "Packard Bell DOTS", ALC662_FIXUP_INV_DMIC),
 	SND_PCI_QUIRK(0x1025, 0x0308, "Acer Aspire 8942G", ALC662_FIXUP_ASPIRE),
@@ -10678,7 +11818,13 @@
 	SND_PCI_QUIRK(0x1028, 0x0698, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1028, 0x069f, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x1632, "HP RP5800", ALC662_FIXUP_HP_RP5800),
+	SND_PCI_QUIRK(0x103c, 0x870c, "HP", ALC897_FIXUP_HP_HSMIC_VERB),
+	SND_PCI_QUIRK(0x103c, 0x8719, "HP", ALC897_FIXUP_HP_HSMIC_VERB),
+	SND_PCI_QUIRK(0x103c, 0x872b, "HP", ALC897_FIXUP_HP_HSMIC_VERB),
 	SND_PCI_QUIRK(0x103c, 0x873e, "HP", ALC671_FIXUP_HP_HEADSET_MIC2),
+	SND_PCI_QUIRK(0x103c, 0x8768, "HP Slim Desktop S01", ALC671_FIXUP_HP_HEADSET_MIC2),
+	SND_PCI_QUIRK(0x103c, 0x877e, "HP 288 Pro G6", ALC671_FIXUP_HP_HEADSET_MIC2),
+	SND_PCI_QUIRK(0x103c, 0x885f, "HP 288 Pro G8", ALC671_FIXUP_HP_HEADSET_MIC2),
 	SND_PCI_QUIRK(0x1043, 0x1080, "Asus UX501VW", ALC668_FIXUP_HEADSET_MODE),
 	SND_PCI_QUIRK(0x1043, 0x11cd, "Asus N550", ALC662_FIXUP_ASUS_Nx50),
 	SND_PCI_QUIRK(0x1043, 0x129d, "Asus N750", ALC662_FIXUP_ASUS_Nx50),
@@ -10697,6 +11843,16 @@
 	SND_PCI_QUIRK(0x144d, 0xc051, "Samsung R720", ALC662_FIXUP_IDEAPAD),
 	SND_PCI_QUIRK(0x14cd, 0x5003, "USI", ALC662_FIXUP_USI_HEADSET_MODE),
 	SND_PCI_QUIRK(0x17aa, 0x1036, "Lenovo P520", ALC662_FIXUP_LENOVO_MULTI_CODECS),
+	SND_PCI_QUIRK(0x17aa, 0x1057, "Lenovo P360", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x1064, "Lenovo P3 Tower", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x32ca, "Lenovo ThinkCentre M80", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x32cb, "Lenovo ThinkCentre M70", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x32cf, "Lenovo ThinkCentre M950", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x32f7, "Lenovo ThinkCentre M90", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x3321, "Lenovo ThinkCentre M70 Gen4", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x331b, "Lenovo ThinkCentre M90 Gen4", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x3364, "Lenovo ThinkCentre M90 Gen5", ALC897_FIXUP_HEADSET_MIC_PIN),
+	SND_PCI_QUIRK(0x17aa, 0x3742, "Lenovo TianYi510Pro-14IOB", ALC897_FIXUP_HEADSET_MIC_PIN2),
 	SND_PCI_QUIRK(0x17aa, 0x38af, "Lenovo Ideapad Y550P", ALC662_FIXUP_IDEAPAD),
 	SND_PCI_QUIRK(0x17aa, 0x3a0d, "Lenovo Ideapad Y550", ALC662_FIXUP_IDEAPAD),
 	SND_PCI_QUIRK(0x1849, 0x5892, "ASRock B150M", ALC892_FIXUP_ASROCK_MOBO),
@@ -10704,6 +11860,7 @@
 	SND_PCI_QUIRK(0x1b0a, 0x01b8, "ACER Veriton", ALC662_FIXUP_ACER_VERITON),
 	SND_PCI_QUIRK(0x1b35, 0x1234, "CZC ET26", ALC662_FIXUP_CZC_ET26),
 	SND_PCI_QUIRK(0x1b35, 0x2206, "CZC P10T", ALC662_FIXUP_CZC_P10T),
+	SND_PCI_QUIRK(0x1c6c, 0x1239, "Compaq N14JP6-V2", ALC897_FIXUP_HP_HSMIC_VERB),
 
 #if 0
 	/* Below is a quirk table taken from the old code.
@@ -10798,6 +11955,7 @@
 	{.id = ALC662_FIXUP_USI_HEADSET_MODE, .name = "usi-headset"},
 	{.id = ALC662_FIXUP_LENOVO_MULTI_CODECS, .name = "dual-codecs"},
 	{.id = ALC669_FIXUP_ACER_ASPIRE_ETHOS, .name = "aspire-ethos"},
+	{.id = ALC897_FIXUP_UNIS_H3C_X500S, .name = "unis-h3c-x500s"},
 	{}
 };
 
@@ -11051,6 +12209,7 @@
 	HDA_CODEC_ENTRY(0x10ec0b00, "ALCS1200A", patch_alc882),
 	HDA_CODEC_ENTRY(0x10ec1168, "ALC1220", patch_alc882),
 	HDA_CODEC_ENTRY(0x10ec1220, "ALC1220", patch_alc882),
+	HDA_CODEC_ENTRY(0x19e58326, "HW8326", patch_alc269),
 	{} /* terminator */
 };
 MODULE_DEVICE_TABLE(hdaudio, snd_hda_id_realtek);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_sigmatel.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_sigmatel.c
@@ -209,6 +209,7 @@
 
 	/* beep widgets */
 	hda_nid_t anabeep_nid;
+	bool beep_power_on;
 
 	/* SPDIF-out mux */
 	const char * const *spdif_labels;
@@ -1706,6 +1707,7 @@
 };
 
 static const struct hda_pintbl ref92hd73xx_pin_configs[] = {
+	// Port A-H
 	{ 0x0a, 0x02214030 },
 	{ 0x0b, 0x02a19040 },
 	{ 0x0c, 0x01a19020 },
@@ -1714,9 +1716,12 @@
 	{ 0x0f, 0x01014010 },
 	{ 0x10, 0x01014020 },
 	{ 0x11, 0x01014030 },
+	// CD in
 	{ 0x12, 0x02319040 },
+	// Digial Mic ins
 	{ 0x13, 0x90a000f0 },
 	{ 0x14, 0x90a000f0 },
+	// Digital outs
 	{ 0x22, 0x01452050 },
 	{ 0x23, 0x01452050 },
 	{}
@@ -1757,6 +1762,7 @@
 };
 
 static const struct hda_pintbl intel_dg45id_pin_configs[] = {
+	// Analog outputs
 	{ 0x0a, 0x02214230 },
 	{ 0x0b, 0x02A19240 },
 	{ 0x0c, 0x01013214 },
@@ -1764,6 +1770,9 @@
 	{ 0x0e, 0x01A19250 },
 	{ 0x0f, 0x01011212 },
 	{ 0x10, 0x01016211 },
+	// Digital output
+	{ 0x22, 0x01451380 },
+	{ 0x23, 0x40f000f0 },
 	{}
 };
 
@@ -1954,6 +1963,8 @@
 				"DFI LanParty", STAC_92HD73XX_REF),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DFI, 0x3101,
 				"DFI LanParty", STAC_92HD73XX_REF),
+	SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5001,
+				"Intel DP45SG", STAC_92HD73XX_INTEL),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5002,
 				"Intel DG45ID", STAC_92HD73XX_INTEL),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5003,
@@ -4310,6 +4321,8 @@
 		if (codec->beep) {
 			/* IDT/STAC codecs have linear beep tone parameter */
 			codec->beep->linear_tone = spec->linear_tone_beep;
+			/* keep power up while beep is enabled */
+			codec->beep->keep_power_at_enable = 1;
 			/* if no beep switch is available, make its own one */
 			caps = query_amp_caps(codec, nid, HDA_OUTPUT);
 			if (!(caps & AC_AMPCAP_MUTE)) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/hda/patch_via.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/hda/patch_via.c
@@ -520,11 +520,11 @@
 	if (err < 0)
 		return err;
 
-	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
+	err = auto_parse_beep(codec);
 	if (err < 0)
 		return err;
 
-	err = auto_parse_beep(codec);
+	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
 	if (err < 0)
 		return err;
 
@@ -821,6 +821,9 @@
 		return 0;
 	nums = snd_hda_get_connections(codec, spec->gen.mixer_nid, conn,
 				       ARRAY_SIZE(conn) - 1);
+	if (nums < 0)
+		return nums;
+
 	for (i = 0; i < nums; i++) {
 		if (get_wcaps_type(get_wcaps(codec, conn[i])) == AC_WID_AUD_OUT)
 			return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ice1712/aureon.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ice1712/aureon.c
@@ -1892,6 +1892,7 @@
 		unsigned char id;
 		snd_ice1712_save_gpio_status(ice);
 		id = aureon_cs8415_get(ice, CS8415_ID);
+		snd_ice1712_restore_gpio_status(ice);
 		if (id != 0x41)
 			dev_info(ice->card->dev,
 				 "No CS8415 chip. Skipping CS8415 controls.\n");
@@ -1909,7 +1910,6 @@
 					kctl->id.device = ice->pcm->device;
 			}
 		}
-		snd_ice1712_restore_gpio_status(ice);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ice1712/ice1724.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ice1712/ice1724.c
@@ -2519,8 +2519,8 @@
  *
  */
 
-static int snd_vt1724_probe(struct pci_dev *pci,
-			    const struct pci_device_id *pci_id)
+static int __snd_vt1724_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2662,6 +2662,12 @@
 	return 0;
 }
 
+static int snd_vt1724_probe(struct pci_dev *pci,
+			    const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_vt1724_probe(pci, pci_id));
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int snd_vt1724_suspend(struct device *dev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/intel8x0.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/intel8x0.c
@@ -3109,8 +3109,8 @@
 	return 0;
 }
 
-static int snd_intel8x0_probe(struct pci_dev *pci,
-			      const struct pci_device_id *pci_id)
+static int __snd_intel8x0_probe(struct pci_dev *pci,
+				const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct intel8x0 *chip;
@@ -3189,6 +3189,12 @@
 	return 0;
 }
 
+static int snd_intel8x0_probe(struct pci_dev *pci,
+			      const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_intel8x0_probe(pci, pci_id));
+}
+
 static struct pci_driver intel8x0_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_intel8x0_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/intel8x0m.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/intel8x0m.c
@@ -1178,8 +1178,8 @@
 	{ 0 },
 };
 
-static int snd_intel8x0m_probe(struct pci_dev *pci,
-			       const struct pci_device_id *pci_id)
+static int __snd_intel8x0m_probe(struct pci_dev *pci,
+				 const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct intel8x0m *chip;
@@ -1225,6 +1225,12 @@
 	return 0;
 }
 
+static int snd_intel8x0m_probe(struct pci_dev *pci,
+			       const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_intel8x0m_probe(pci, pci_id));
+}
+
 static struct pci_driver intel8x0m_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_intel8x0m_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/korg1212/korg1212.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/korg1212/korg1212.c
@@ -2355,7 +2355,7 @@
 
 	err = snd_korg1212_create(card, pci);
 	if (err < 0)
-		return err;
+		goto error;
 
 	strcpy(card->driver, "korg1212");
 	strcpy(card->shortname, "korg1212");
@@ -2366,10 +2366,14 @@
 
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver korg1212_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/lola/lola.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/lola/lola.c
@@ -637,8 +637,8 @@
 	return 0;
 }
 
-static int lola_probe(struct pci_dev *pci,
-		      const struct pci_device_id *pci_id)
+static int __lola_probe(struct pci_dev *pci,
+			const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -687,6 +687,12 @@
 	return 0;
 }
 
+static int lola_probe(struct pci_dev *pci,
+		      const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __lola_probe(pci, pci_id));
+}
+
 /* PCI IDs */
 static const struct pci_device_id lola_ids[] = {
 	{ PCI_VDEVICE(DIGIGRAM, 0x0001) },
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/lx6464es/lx6464es.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/lx6464es/lx6464es.c
@@ -1019,7 +1019,7 @@
 	err = snd_lx6464es_create(card, pci);
 	if (err < 0) {
 		dev_err(card->dev, "error during snd_lx6464es_create\n");
-		return err;
+		goto error;
 	}
 
 	strcpy(card->driver, "LX6464ES");
@@ -1036,12 +1036,16 @@
 
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 
 	dev_dbg(chip->card->dev, "initialization successful\n");
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver lx6464es_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/lx6464es/lx_core.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/lx6464es/lx_core.c
@@ -493,12 +493,11 @@
 		dev_dbg(chip->card->dev,
 			"CMD_08_ASK_BUFFERS: needed %d, freed %d\n",
 			    *r_needed, *r_freed);
-		for (i = 0; i < MAX_STREAM_BUFFER; ++i) {
-			for (i = 0; i != chip->rmh.stat_len; ++i)
-				dev_dbg(chip->card->dev,
-					"  stat[%d]: %x, %x\n", i,
-					    chip->rmh.stat[i],
-					    chip->rmh.stat[i] & MASK_DATA_SIZE);
+		for (i = 0; i < MAX_STREAM_BUFFER && i < chip->rmh.stat_len;
+		     ++i) {
+			dev_dbg(chip->card->dev, "  stat[%d]: %x, %x\n", i,
+				chip->rmh.stat[i],
+				chip->rmh.stat[i] & MASK_DATA_SIZE);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/maestro3.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/maestro3.c
@@ -2637,7 +2637,7 @@
 /*
  */
 static int
-snd_m3_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+__snd_m3_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2702,6 +2702,12 @@
 	return 0;
 }
 
+static int
+snd_m3_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_m3_probe(pci, pci_id));
+}
+
 static struct pci_driver m3_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_m3_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/nm256/nm256.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/nm256/nm256.c
@@ -1573,7 +1573,6 @@
 	chip->coeffs_current = 0;
 
 	snd_nm256_init_chip(chip);
-	card->private_free = snd_nm256_free;
 
 	// pci_set_master(pci); /* needed? */
 	return 0;
@@ -1680,6 +1679,7 @@
 	err = snd_card_register(card);
 	if (err < 0)
 		return err;
+	card->private_free = snd_nm256_free;
 
 	pci_set_drvdata(pci, card);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/oxygen/oxygen_lib.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/oxygen/oxygen_lib.c
@@ -576,7 +576,7 @@
 	mutex_destroy(&chip->mutex);
 }
 
-int oxygen_pci_probe(struct pci_dev *pci, int index, char *id,
+static int __oxygen_pci_probe(struct pci_dev *pci, int index, char *id,
 		     struct module *owner,
 		     const struct pci_device_id *ids,
 		     int (*get_model)(struct oxygen *chip,
@@ -701,6 +701,16 @@
 	pci_set_drvdata(pci, card);
 	return 0;
 }
+
+int oxygen_pci_probe(struct pci_dev *pci, int index, char *id,
+		     struct module *owner,
+		     const struct pci_device_id *ids,
+		     int (*get_model)(struct oxygen *chip,
+				      const struct pci_device_id *id))
+{
+	return snd_card_free_on_error(&pci->dev,
+				      __oxygen_pci_probe(pci, index, id, owner, ids, get_model));
+}
 EXPORT_SYMBOL(oxygen_pci_probe);
 
 #ifdef CONFIG_PM_SLEEP
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/oxygen/oxygen_mixer.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/oxygen/oxygen_mixer.c
@@ -718,7 +718,7 @@
 	oldreg = oxygen_read_ac97(chip, 1, AC97_REC_GAIN);
 	newreg = oldreg & ~0x0707;
 	newreg = newreg | (value->value.integer.value[0] & 7);
-	newreg = newreg | ((value->value.integer.value[0] & 7) << 8);
+	newreg = newreg | ((value->value.integer.value[1] & 7) << 8);
 	change = newreg != oldreg;
 	if (change)
 		oxygen_write_ac97(chip, 1, AC97_REC_GAIN, newreg);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/riptide/riptide.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/riptide/riptide.c
@@ -2023,7 +2023,7 @@
 #endif
 
 static int
-snd_card_riptide_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+__snd_card_riptide_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -2124,6 +2124,12 @@
 	return 0;
 }
 
+static int
+snd_card_riptide_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_card_riptide_probe(pci, pci_id));
+}
+
 static struct pci_driver driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_riptide_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/rme32.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/rme32.c
@@ -1875,7 +1875,7 @@
 }
 
 static int
-snd_rme32_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+__snd_rme32_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct rme32 *rme32;
@@ -1927,6 +1927,12 @@
 	return 0;
 }
 
+static int
+snd_rme32_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_rme32_probe(pci, pci_id));
+}
+
 static struct pci_driver rme32_driver = {
 	.name =		KBUILD_MODNAME,
 	.id_table =	snd_rme32_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/rme96.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/rme96.c
@@ -2430,8 +2430,8 @@
 }
 
 static int
-snd_rme96_probe(struct pci_dev *pci,
-		const struct pci_device_id *pci_id)
+__snd_rme96_probe(struct pci_dev *pci,
+		  const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct rme96 *rme96;
@@ -2498,6 +2498,12 @@
 	return 0;
 }
 
+static int snd_rme96_probe(struct pci_dev *pci,
+			   const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_rme96_probe(pci, pci_id));
+}
+
 static struct pci_driver rme96_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_rme96_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/rme9652/hdsp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/rme9652/hdsp.c
@@ -433,7 +433,7 @@
     struct snd_rawmidi           *rmidi;
     struct snd_rawmidi_substream *input;
     struct snd_rawmidi_substream *output;
-    char                     istimer; /* timer in use */
+    signed char		     istimer; /* timer in use */
     struct timer_list	     timer;
     spinlock_t               lock;
     int			     pending;
@@ -468,8 +468,11 @@
 	unsigned char         ss_out_channels;
 	u32                   io_loopback;          /* output loopback channel states*/
 
-	struct snd_dma_buffer *capture_dma_buf;
-	struct snd_dma_buffer *playback_dma_buf;
+	/* DMA buffers; those are copied instances from the original snd_dma_buf
+	 * objects (which are managed via devres) for the address alignments
+	 */
+	struct snd_dma_buffer capture_dma_buf;
+	struct snd_dma_buffer playback_dma_buf;
 	unsigned char        *capture_buffer;	    /* suitably aligned address */
 	unsigned char        *playback_buffer;	    /* suitably aligned address */
 
@@ -477,7 +480,7 @@
 	pid_t                 playback_pid;
 	int                   running;
 	int                   system_sample_rate;
-	const char           *channel_map;
+	const signed char    *channel_map;
 	int                   dev;
 	int                   irq;
 	unsigned long         port;
@@ -499,7 +502,7 @@
    where the data for that channel can be read/written from/to.
 */
 
-static const char channel_map_df_ss[HDSP_MAX_CHANNELS] = {
+static const signed char channel_map_df_ss[HDSP_MAX_CHANNELS] = {
 	0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
 	18, 19, 20, 21, 22, 23, 24, 25
 };
@@ -514,7 +517,7 @@
 	-1, -1, -1, -1, -1, -1, -1, -1
 };
 
-static const char channel_map_ds[HDSP_MAX_CHANNELS] = {
+static const signed char channel_map_ds[HDSP_MAX_CHANNELS] = {
 	/* ADAT channels are remapped */
 	1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23,
 	/* channels 12 and 13 are S/PDIF */
@@ -523,7 +526,7 @@
 	-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1
 };
 
-static const char channel_map_H9632_ss[HDSP_MAX_CHANNELS] = {
+static const signed char channel_map_H9632_ss[HDSP_MAX_CHANNELS] = {
 	/* ADAT channels */
 	0, 1, 2, 3, 4, 5, 6, 7,
 	/* SPDIF */
@@ -537,7 +540,7 @@
 	-1, -1
 };
 
-static const char channel_map_H9632_ds[HDSP_MAX_CHANNELS] = {
+static const signed char channel_map_H9632_ds[HDSP_MAX_CHANNELS] = {
 	/* ADAT */
 	1, 3, 5, 7,
 	/* SPDIF */
@@ -551,7 +554,7 @@
 	-1, -1, -1, -1, -1, -1
 };
 
-static const char channel_map_H9632_qs[HDSP_MAX_CHANNELS] = {
+static const signed char channel_map_H9632_qs[HDSP_MAX_CHANNELS] = {
 	/* ADAT is disabled in this mode */
 	/* SPDIF */
 	8, 9,
@@ -1295,8 +1298,10 @@
 
 static void snd_hdsp_flush_midi_input (struct hdsp *hdsp, int id)
 {
-	while (snd_hdsp_midi_input_available (hdsp, id))
-		snd_hdsp_midi_read_byte (hdsp, id);
+	int count = 256;
+
+	while (snd_hdsp_midi_input_available(hdsp, id) && --count)
+		snd_hdsp_midi_read_byte(hdsp, id);
 }
 
 static int snd_hdsp_midi_output_write (struct hdsp_midi *hmidi)
@@ -3764,30 +3769,32 @@
 
 static int snd_hdsp_initialize_memory(struct hdsp *hdsp)
 {
-	unsigned long pb_bus, cb_bus;
+	struct snd_dma_buffer *capture_dma, *playback_dma;
 
-	hdsp->capture_dma_buf =
-		snd_hammerfall_get_buffer(hdsp->pci, HDSP_DMA_AREA_BYTES);
-	hdsp->playback_dma_buf =
-		snd_hammerfall_get_buffer(hdsp->pci, HDSP_DMA_AREA_BYTES);
-	if (!hdsp->capture_dma_buf || !hdsp->playback_dma_buf) {
+	capture_dma = snd_hammerfall_get_buffer(hdsp->pci, HDSP_DMA_AREA_BYTES);
+	playback_dma = snd_hammerfall_get_buffer(hdsp->pci, HDSP_DMA_AREA_BYTES);
+	if (!capture_dma || !playback_dma) {
 		dev_err(hdsp->card->dev,
 			"%s: no buffers available\n", hdsp->card_name);
 		return -ENOMEM;
 	}
 
-	/* Align to bus-space 64K boundary */
+	/* copy to the own data for alignment */
+	hdsp->capture_dma_buf = *capture_dma;
+	hdsp->playback_dma_buf = *playback_dma;
 
-	cb_bus = ALIGN(hdsp->capture_dma_buf->addr, 0x10000ul);
-	pb_bus = ALIGN(hdsp->playback_dma_buf->addr, 0x10000ul);
+	/* Align to bus-space 64K boundary */
+	hdsp->capture_dma_buf.addr = ALIGN(capture_dma->addr, 0x10000ul);
+	hdsp->playback_dma_buf.addr = ALIGN(playback_dma->addr, 0x10000ul);
 
 	/* Tell the card where it is */
+	hdsp_write(hdsp, HDSP_inputBufferAddress, hdsp->capture_dma_buf.addr);
+	hdsp_write(hdsp, HDSP_outputBufferAddress, hdsp->playback_dma_buf.addr);
 
-	hdsp_write(hdsp, HDSP_inputBufferAddress, cb_bus);
-	hdsp_write(hdsp, HDSP_outputBufferAddress, pb_bus);
-
-	hdsp->capture_buffer = hdsp->capture_dma_buf->area + (cb_bus - hdsp->capture_dma_buf->addr);
-	hdsp->playback_buffer = hdsp->playback_dma_buf->area + (pb_bus - hdsp->playback_dma_buf->addr);
+	hdsp->capture_dma_buf.area += hdsp->capture_dma_buf.addr - capture_dma->addr;
+	hdsp->playback_dma_buf.area += hdsp->playback_dma_buf.addr - playback_dma->addr;
+	hdsp->capture_buffer = hdsp->capture_dma_buf.area;
+	hdsp->playback_buffer = hdsp->playback_dma_buf.area;
 
 	return 0;
 }
@@ -3934,7 +3941,7 @@
 	return hdsp_hw_pointer(hdsp);
 }
 
-static char *hdsp_channel_buffer_location(struct hdsp *hdsp,
+static signed char *hdsp_channel_buffer_location(struct hdsp *hdsp,
 					     int stream,
 					     int channel)
 
@@ -3959,7 +3966,7 @@
 				  void __user *src, unsigned long count)
 {
 	struct hdsp *hdsp = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	if (snd_BUG_ON(pos + count > HDSP_CHANNEL_BUFFER_BYTES))
 		return -EINVAL;
@@ -3977,7 +3984,7 @@
 					 void *src, unsigned long count)
 {
 	struct hdsp *hdsp = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	channel_buf = hdsp_channel_buffer_location(hdsp, substream->pstr->stream, channel);
 	if (snd_BUG_ON(!channel_buf))
@@ -3991,7 +3998,7 @@
 				 void __user *dst, unsigned long count)
 {
 	struct hdsp *hdsp = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	if (snd_BUG_ON(pos + count > HDSP_CHANNEL_BUFFER_BYTES))
 		return -EINVAL;
@@ -4009,7 +4016,7 @@
 					void *dst, unsigned long count)
 {
 	struct hdsp *hdsp = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	channel_buf = hdsp_channel_buffer_location(hdsp, substream->pstr->stream, channel);
 	if (snd_BUG_ON(!channel_buf))
@@ -4023,7 +4030,7 @@
 			       unsigned long count)
 {
 	struct hdsp *hdsp = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	channel_buf = hdsp_channel_buffer_location (hdsp, substream->pstr->stream, channel);
 	if (snd_BUG_ON(!channel_buf))
@@ -4507,7 +4514,7 @@
 	snd_pcm_set_sync(substream);
 
         runtime->hw = snd_hdsp_playback_subinfo;
-	snd_pcm_set_runtime_buffer(substream, hdsp->playback_dma_buf);
+	snd_pcm_set_runtime_buffer(substream, &hdsp->playback_dma_buf);
 
 	hdsp->playback_pid = current->pid;
 	hdsp->playback_substream = substream;
@@ -4583,7 +4590,7 @@
 	snd_pcm_set_sync(substream);
 
 	runtime->hw = snd_hdsp_capture_subinfo;
-	snd_pcm_set_runtime_buffer(substream, hdsp->capture_dma_buf);
+	snd_pcm_set_runtime_buffer(substream, &hdsp->capture_dma_buf);
 
 	hdsp->capture_pid = current->pid;
 	hdsp->capture_substream = substream;
@@ -5439,17 +5446,21 @@
 	hdsp->pci = pci;
 	err = snd_hdsp_create(card, hdsp);
 	if (err)
-		return err;
+		goto error;
 
 	strcpy(card->shortname, "Hammerfall DSP");
 	sprintf(card->longname, "%s at 0x%lx, irq %d", hdsp->card_name,
 		hdsp->port, hdsp->irq);
 	err = snd_card_register(card);
 	if (err)
-		return err;
+		goto error;
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver hdsp_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/rme9652/hdspm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/rme9652/hdspm.c
@@ -1838,8 +1838,10 @@
 
 static void snd_hdspm_flush_midi_input(struct hdspm *hdspm, int id)
 {
-	while (snd_hdspm_midi_input_available (hdspm, id))
-		snd_hdspm_midi_read_byte (hdspm, id);
+	int count = 256;
+
+	while (snd_hdspm_midi_input_available(hdspm, id) && --count)
+		snd_hdspm_midi_read_byte(hdspm, id);
 }
 
 static int snd_hdspm_midi_output_write (struct hdspm_midi *hmidi)
@@ -6895,7 +6897,7 @@
 
 	err = snd_hdspm_create(card, hdspm);
 	if (err < 0)
-		return err;
+		goto error;
 
 	if (hdspm->io_type != MADIface) {
 		snprintf(card->shortname, sizeof(card->shortname), "%s_%x",
@@ -6914,12 +6916,16 @@
 
 	err = snd_card_register(card);
 	if (err < 0)
-		return err;
+		goto error;
 
 	pci_set_drvdata(pci, card);
 
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver hdspm_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/rme9652/rme9652.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/rme9652/rme9652.c
@@ -208,8 +208,11 @@
 	unsigned char ds_channels;
 	unsigned char ss_channels;	/* different for hammerfall/hammerfall-light */
 
-	struct snd_dma_buffer *playback_dma_buf;
-	struct snd_dma_buffer *capture_dma_buf;
+	/* DMA buffers; those are copied instances from the original snd_dma_buf
+	 * objects (which are managed via devres) for the address alignments
+	 */
+	struct snd_dma_buffer playback_dma_buf;
+	struct snd_dma_buffer capture_dma_buf;
 
 	unsigned char *capture_buffer;	/* suitably aligned address */
 	unsigned char *playback_buffer;	/* suitably aligned address */
@@ -227,7 +230,7 @@
 	int last_spdif_sample_rate;	/* so that we can catch externally ... */
 	int last_adat_sample_rate;	/* ... induced rate changes            */
 
-	const char *channel_map;
+	const signed char *channel_map;
 
 	struct snd_card *card;
 	struct snd_pcm *pcm;
@@ -244,12 +247,12 @@
    where the data for that channel can be read/written from/to.
 */
 
-static const char channel_map_9652_ss[26] = {
+static const signed char channel_map_9652_ss[26] = {
 	0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
 	18, 19, 20, 21, 22, 23, 24, 25
 };
 
-static const char channel_map_9636_ss[26] = {
+static const signed char channel_map_9636_ss[26] = {
 	0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 
 	/* channels 16 and 17 are S/PDIF */
 	24, 25,
@@ -257,7 +260,7 @@
 	-1, -1, -1, -1, -1, -1, -1, -1
 };
 
-static const char channel_map_9652_ds[26] = {
+static const signed char channel_map_9652_ds[26] = {
 	/* ADAT channels are remapped */
 	1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23,
 	/* channels 12 and 13 are S/PDIF */
@@ -266,7 +269,7 @@
 	-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1
 };
 
-static const char channel_map_9636_ds[26] = {
+static const signed char channel_map_9636_ds[26] = {
 	/* ADAT channels are remapped */
 	1, 3, 5, 7, 9, 11, 13, 15,
 	/* channels 8 and 9 are S/PDIF */
@@ -1719,30 +1722,32 @@
 
 static int snd_rme9652_initialize_memory(struct snd_rme9652 *rme9652)
 {
-	unsigned long pb_bus, cb_bus;
+	struct snd_dma_buffer *capture_dma, *playback_dma;
 
-	rme9652->capture_dma_buf =
-		snd_hammerfall_get_buffer(rme9652->pci, RME9652_DMA_AREA_BYTES);
-	rme9652->playback_dma_buf =
-		snd_hammerfall_get_buffer(rme9652->pci, RME9652_DMA_AREA_BYTES);
-	if (!rme9652->capture_dma_buf || !rme9652->playback_dma_buf) {
+	capture_dma = snd_hammerfall_get_buffer(rme9652->pci, RME9652_DMA_AREA_BYTES);
+	playback_dma = snd_hammerfall_get_buffer(rme9652->pci, RME9652_DMA_AREA_BYTES);
+	if (!capture_dma || !playback_dma) {
 		dev_err(rme9652->card->dev,
 			"%s: no buffers available\n", rme9652->card_name);
 		return -ENOMEM;
 	}
 
-	/* Align to bus-space 64K boundary */
+	/* copy to the own data for alignment */
+	rme9652->capture_dma_buf = *capture_dma;
+	rme9652->playback_dma_buf = *playback_dma;
 
-	cb_bus = ALIGN(rme9652->capture_dma_buf->addr, 0x10000ul);
-	pb_bus = ALIGN(rme9652->playback_dma_buf->addr, 0x10000ul);
+	/* Align to bus-space 64K boundary */
+	rme9652->capture_dma_buf.addr = ALIGN(capture_dma->addr, 0x10000ul);
+	rme9652->playback_dma_buf.addr = ALIGN(playback_dma->addr, 0x10000ul);
 
 	/* Tell the card where it is */
+	rme9652_write(rme9652, RME9652_rec_buffer, rme9652->capture_dma_buf.addr);
+	rme9652_write(rme9652, RME9652_play_buffer, rme9652->playback_dma_buf.addr);
 
-	rme9652_write(rme9652, RME9652_rec_buffer, cb_bus);
-	rme9652_write(rme9652, RME9652_play_buffer, pb_bus);
-
-	rme9652->capture_buffer = rme9652->capture_dma_buf->area + (cb_bus - rme9652->capture_dma_buf->addr);
-	rme9652->playback_buffer = rme9652->playback_dma_buf->area + (pb_bus - rme9652->playback_dma_buf->addr);
+	rme9652->capture_dma_buf.area += rme9652->capture_dma_buf.addr - capture_dma->addr;
+	rme9652->playback_dma_buf.area += rme9652->playback_dma_buf.addr - playback_dma->addr;
+	rme9652->capture_buffer = rme9652->capture_dma_buf.area;
+	rme9652->playback_buffer = rme9652->playback_dma_buf.area;
 
 	return 0;
 }
@@ -1814,7 +1819,7 @@
 	return rme9652_hw_pointer(rme9652);
 }
 
-static char *rme9652_channel_buffer_location(struct snd_rme9652 *rme9652,
+static signed char *rme9652_channel_buffer_location(struct snd_rme9652 *rme9652,
 					     int stream,
 					     int channel)
 
@@ -1842,7 +1847,7 @@
 				     void __user *src, unsigned long count)
 {
 	struct snd_rme9652 *rme9652 = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	if (snd_BUG_ON(pos + count > RME9652_CHANNEL_BUFFER_BYTES))
 		return -EINVAL;
@@ -1862,7 +1867,7 @@
 					    void *src, unsigned long count)
 {
 	struct snd_rme9652 *rme9652 = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	channel_buf = rme9652_channel_buffer_location(rme9652,
 						      substream->pstr->stream,
@@ -1878,7 +1883,7 @@
 				    void __user *dst, unsigned long count)
 {
 	struct snd_rme9652 *rme9652 = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	if (snd_BUG_ON(pos + count > RME9652_CHANNEL_BUFFER_BYTES))
 		return -EINVAL;
@@ -1898,7 +1903,7 @@
 					   void *dst, unsigned long count)
 {
 	struct snd_rme9652 *rme9652 = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	channel_buf = rme9652_channel_buffer_location(rme9652,
 						      substream->pstr->stream,
@@ -1914,7 +1919,7 @@
 				  unsigned long count)
 {
 	struct snd_rme9652 *rme9652 = snd_pcm_substream_chip(substream);
-	char *channel_buf;
+	signed char *channel_buf;
 
 	channel_buf = rme9652_channel_buffer_location (rme9652,
 						       substream->pstr->stream,
@@ -2259,7 +2264,7 @@
 	snd_pcm_set_sync(substream);
 
         runtime->hw = snd_rme9652_playback_subinfo;
-	snd_pcm_set_runtime_buffer(substream, rme9652->playback_dma_buf);
+	snd_pcm_set_runtime_buffer(substream, &rme9652->playback_dma_buf);
 
 	if (rme9652->capture_substream == NULL) {
 		rme9652_stop(rme9652);
@@ -2318,7 +2323,7 @@
 	snd_pcm_set_sync(substream);
 
 	runtime->hw = snd_rme9652_capture_subinfo;
-	snd_pcm_set_runtime_buffer(substream, rme9652->capture_dma_buf);
+	snd_pcm_set_runtime_buffer(substream, &rme9652->capture_dma_buf);
 
 	if (rme9652->playback_substream == NULL) {
 		rme9652_stop(rme9652);
@@ -2567,7 +2572,7 @@
 	rme9652->pci = pci;
 	err = snd_rme9652_create(card, rme9652, precise_ptr[dev]);
 	if (err)
-		return err;
+		goto error;
 
 	strcpy(card->shortname, rme9652->card_name);
 
@@ -2575,10 +2580,14 @@
 		card->shortname, rme9652->port, rme9652->irq);
 	err = snd_card_register(card);
 	if (err)
-		return err;
+		goto error;
 	pci_set_drvdata(pci, card);
 	dev++;
 	return 0;
+
+ error:
+	snd_card_free(card);
+	return err;
 }
 
 static struct pci_driver rme9652_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/sis7019.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/sis7019.c
@@ -1331,8 +1331,8 @@
 	return 0;
 }
 
-static int snd_sis7019_probe(struct pci_dev *pci,
-			     const struct pci_device_id *pci_id)
+static int __snd_sis7019_probe(struct pci_dev *pci,
+			       const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct sis7019 *sis;
@@ -1352,8 +1352,8 @@
 	if (!codecs)
 		codecs = SIS_PRIMARY_CODEC_PRESENT;
 
-	rc = snd_card_new(&pci->dev, index, id, THIS_MODULE,
-			  sizeof(*sis), &card);
+	rc = snd_devm_card_new(&pci->dev, index, id, THIS_MODULE,
+			       sizeof(*sis), &card);
 	if (rc < 0)
 		return rc;
 
@@ -1386,6 +1386,12 @@
 	return 0;
 }
 
+static int snd_sis7019_probe(struct pci_dev *pci,
+			     const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_sis7019_probe(pci, pci_id));
+}
+
 static struct pci_driver sis7019_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_sis7019_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/sonicvibes.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/sonicvibes.c
@@ -1387,8 +1387,8 @@
 	return 0;
 }
 
-static int snd_sonic_probe(struct pci_dev *pci,
-			   const struct pci_device_id *pci_id)
+static int __snd_sonic_probe(struct pci_dev *pci,
+			     const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -1459,6 +1459,12 @@
 	return 0;
 }
 
+static int snd_sonic_probe(struct pci_dev *pci,
+			   const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_sonic_probe(pci, pci_id));
+}
+
 static struct pci_driver sonicvibes_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_sonic_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/via82xx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/via82xx.c
@@ -2458,8 +2458,8 @@
 	return VIA_DXS_48K;
 };
 
-static int snd_via82xx_probe(struct pci_dev *pci,
-			     const struct pci_device_id *pci_id)
+static int __snd_via82xx_probe(struct pci_dev *pci,
+			       const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct via82xx *chip;
@@ -2569,6 +2569,12 @@
 	return 0;
 }
 
+static int snd_via82xx_probe(struct pci_dev *pci,
+			     const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_via82xx_probe(pci, pci_id));
+}
+
 static struct pci_driver via82xx_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_via82xx_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/via82xx_modem.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/via82xx_modem.c
@@ -1103,8 +1103,8 @@
 }
 
 
-static int snd_via82xx_probe(struct pci_dev *pci,
-			     const struct pci_device_id *pci_id)
+static int __snd_via82xx_probe(struct pci_dev *pci,
+			       const struct pci_device_id *pci_id)
 {
 	struct snd_card *card;
 	struct via82xx_modem *chip;
@@ -1157,6 +1157,12 @@
 	return 0;
 }
 
+static int snd_via82xx_probe(struct pci_dev *pci,
+			     const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_via82xx_probe(pci, pci_id));
+}
+
 static struct pci_driver via82xx_modem_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_via82xx_modem_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ymfpci/ymfpci.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ymfpci/ymfpci.c
@@ -150,8 +150,8 @@
 void snd_ymfpci_free_gameport(struct snd_ymfpci *chip) { }
 #endif /* SUPPORT_JOYSTICK */
 
-static int snd_card_ymfpci_probe(struct pci_dev *pci,
-				 const struct pci_device_id *pci_id)
+static int __snd_card_ymfpci_probe(struct pci_dev *pci,
+				   const struct pci_device_id *pci_id)
 {
 	static int dev;
 	struct snd_card *card;
@@ -170,7 +170,7 @@
 		return -ENOENT;
 	}
 
-	err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
+	err = snd_devm_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE,
 			   sizeof(*chip), &card);
 	if (err < 0)
 		return err;
@@ -333,6 +333,12 @@
 	return 0;
 }
 
+static int snd_card_ymfpci_probe(struct pci_dev *pci,
+				 const struct pci_device_id *pci_id)
+{
+	return snd_card_free_on_error(&pci->dev, __snd_card_ymfpci_probe(pci, pci_id));
+}
+
 static struct pci_driver ymfpci_driver = {
 	.name = KBUILD_MODNAME,
 	.id_table = snd_ymfpci_ids,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/pci/ymfpci/ymfpci_main.c
+++ linux-xilinx-zynqmp-5.15.0/sound/pci/ymfpci/ymfpci_main.c
@@ -2165,7 +2165,7 @@
 	chip->work_base = ptr;
 	chip->work_base_addr = ptr_addr;
 	
-	snd_BUG_ON(ptr + chip->work_size !=
+	snd_BUG_ON(ptr + PAGE_ALIGN(chip->work_size) !=
 		   chip->work_ptr->area + chip->work_ptr->bytes);
 
 	snd_ymfpci_writel(chip, YDSXGR_PLAYCTRLBASE, chip->bank_base_playback_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/sh/aica.c
+++ linux-xilinx-zynqmp-5.15.0/sound/sh/aica.c
@@ -278,7 +278,8 @@
 		dreamcastcard->clicks++;
 		if (unlikely(dreamcastcard->clicks >= AICA_PERIOD_NUMBER))
 			dreamcastcard->clicks %= AICA_PERIOD_NUMBER;
-		mod_timer(&dreamcastcard->timer, jiffies + 1);
+		if (snd_pcm_running(dreamcastcard->substream))
+			mod_timer(&dreamcastcard->timer, jiffies + 1);
 	}
 }
 
@@ -290,6 +291,8 @@
 	/*timer function - so cannot sleep */
 	int play_period;
 	struct snd_pcm_runtime *runtime;
+	if (!snd_pcm_running(substream))
+		return;
 	runtime = substream->runtime;
 	dreamcastcard = substream->pcm->private_data;
 	/* Have we played out an additional period? */
@@ -350,12 +353,19 @@
 	return 0;
 }
 
+static int snd_aicapcm_pcm_sync_stop(struct snd_pcm_substream *substream)
+{
+	struct snd_card_aica *dreamcastcard = substream->pcm->private_data;
+
+	del_timer_sync(&dreamcastcard->timer);
+	cancel_work_sync(&dreamcastcard->spu_dma_work);
+	return 0;
+}
+
 static int snd_aicapcm_pcm_close(struct snd_pcm_substream
 				 *substream)
 {
 	struct snd_card_aica *dreamcastcard = substream->pcm->private_data;
-	flush_work(&(dreamcastcard->spu_dma_work));
-	del_timer(&dreamcastcard->timer);
 	dreamcastcard->substream = NULL;
 	kfree(dreamcastcard->channel);
 	spu_disable();
@@ -401,6 +411,7 @@
 	.prepare = snd_aicapcm_pcm_prepare,
 	.trigger = snd_aicapcm_pcm_trigger,
 	.pointer = snd_aicapcm_pcm_pointer,
+	.sync_stop = snd_aicapcm_pcm_sync_stop,
 };
 
 /* TO DO: set up to handle more than one pcm instance */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/Kconfig
@@ -61,3 +61,24 @@
 
 	 By enabling this flag build will trigger for ACP PCI driver,
 	 ACP DMA driver, CPU DAI driver.
+
+config SND_SOC_AMD_ACP6x
+	tristate "AMD Audio Coprocessor-v6.x Yellow Carp support"
+	depends on X86 && PCI
+	help
+	  This option enables Audio Coprocessor i.e ACP v6.x support on
+	  AMD Yellow Carp platform. By enabling this flag build will be
+	  triggered for ACP PCI driver, ACP PDM DMA driver.
+	  Say m if you have such a device.
+	  If unsure select "N".
+
+config SND_SOC_AMD_YC_MACH
+	tristate "AMD YC support for DMIC"
+	select SND_SOC_DMIC
+	depends on SND_SOC_AMD_ACP6x
+	help
+	  This option enables machine driver for Yellow Carp platform
+	  using dmic. ACP IP has PDM Decoder block with DMA controller.
+	  DMIC can be connected directly to ACP IP.
+	  Say m if you have such a device.
+	  If unsure select "N".
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/Makefile
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/Makefile
@@ -11,3 +11,4 @@
 obj-$(CONFIG_SND_SOC_AMD_RV_RT5682_MACH) += snd-soc-acp-rt5682-mach.o
 obj-$(CONFIG_SND_SOC_AMD_RENOIR) += renoir/
 obj-$(CONFIG_SND_SOC_AMD_ACP5x) += vangogh/
+obj-$(CONFIG_SND_SOC_AMD_ACP6x) += yc/
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/vangogh/acp5x-pcm-dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/vangogh/acp5x-pcm-dma.c
@@ -281,7 +281,7 @@
 		return -EINVAL;
 	}
 	size = params_buffer_bytes(params);
-	rtd->dma_addr = substream->dma_buffer.addr;
+	rtd->dma_addr = substream->runtime->dma_addr;
 	rtd->num_pages = (PAGE_ALIGN(size) >> PAGE_SHIFT);
 	config_acp5x_dma(rtd, substream->stream);
 	return 0;
@@ -426,51 +426,51 @@
 static int __maybe_unused acp5x_pcm_resume(struct device *dev)
 {
 	struct i2s_dev_data *adata;
-	u32 val, reg_val, frmt_val;
+	struct i2s_stream_instance *rtd;
+	u32 val;
 
-	reg_val = 0;
-	frmt_val = 0;
 	adata = dev_get_drvdata(dev);
 
 	if (adata->play_stream && adata->play_stream->runtime) {
-		struct i2s_stream_instance *rtd =
-			adata->play_stream->runtime->private_data;
+		rtd = adata->play_stream->runtime->private_data;
 		config_acp5x_dma(rtd, SNDRV_PCM_STREAM_PLAYBACK);
-		switch (rtd->i2s_instance) {
-		case I2S_HS_INSTANCE:
-			reg_val = ACP_HSTDM_ITER;
-			frmt_val = ACP_HSTDM_TXFRMT;
-			break;
-		case I2S_SP_INSTANCE:
-		default:
-			reg_val = ACP_I2STDM_ITER;
-			frmt_val = ACP_I2STDM_TXFRMT;
+		acp_writel((rtd->xfer_resolution  << 3), rtd->acp5x_base + ACP_HSTDM_ITER);
+		if (adata->tdm_mode == TDM_ENABLE) {
+			acp_writel(adata->tdm_fmt, adata->acp5x_base + ACP_HSTDM_TXFRMT);
+			val = acp_readl(adata->acp5x_base + ACP_HSTDM_ITER);
+			acp_writel(val | 0x2, adata->acp5x_base + ACP_HSTDM_ITER);
+		}
+	}
+	if (adata->i2ssp_play_stream && adata->i2ssp_play_stream->runtime) {
+		rtd = adata->i2ssp_play_stream->runtime->private_data;
+		config_acp5x_dma(rtd, SNDRV_PCM_STREAM_PLAYBACK);
+		acp_writel((rtd->xfer_resolution  << 3), rtd->acp5x_base + ACP_I2STDM_ITER);
+		if (adata->tdm_mode == TDM_ENABLE) {
+			acp_writel(adata->tdm_fmt, adata->acp5x_base + ACP_I2STDM_TXFRMT);
+			val = acp_readl(adata->acp5x_base + ACP_I2STDM_ITER);
+			acp_writel(val | 0x2, adata->acp5x_base + ACP_I2STDM_ITER);
 		}
-		acp_writel((rtd->xfer_resolution  << 3),
-			   rtd->acp5x_base + reg_val);
 	}
 
 	if (adata->capture_stream && adata->capture_stream->runtime) {
-		struct i2s_stream_instance *rtd =
-			adata->capture_stream->runtime->private_data;
+		rtd = adata->capture_stream->runtime->private_data;
 		config_acp5x_dma(rtd, SNDRV_PCM_STREAM_CAPTURE);
-		switch (rtd->i2s_instance) {
-		case I2S_HS_INSTANCE:
-			reg_val = ACP_HSTDM_IRER;
-			frmt_val = ACP_HSTDM_RXFRMT;
-			break;
-		case I2S_SP_INSTANCE:
-		default:
-			reg_val = ACP_I2STDM_IRER;
-			frmt_val = ACP_I2STDM_RXFRMT;
+		acp_writel((rtd->xfer_resolution  << 3), rtd->acp5x_base + ACP_HSTDM_IRER);
+		if (adata->tdm_mode == TDM_ENABLE) {
+			acp_writel(adata->tdm_fmt, adata->acp5x_base + ACP_HSTDM_RXFRMT);
+			val = acp_readl(adata->acp5x_base + ACP_HSTDM_IRER);
+			acp_writel(val | 0x2, adata->acp5x_base + ACP_HSTDM_IRER);
 		}
-		acp_writel((rtd->xfer_resolution  << 3),
-			   rtd->acp5x_base + reg_val);
 	}
-	if (adata->tdm_mode == TDM_ENABLE) {
-		acp_writel(adata->tdm_fmt, adata->acp5x_base + frmt_val);
-		val = acp_readl(adata->acp5x_base + reg_val);
-		acp_writel(val | 0x2, adata->acp5x_base + reg_val);
+	if (adata->i2ssp_capture_stream && adata->i2ssp_capture_stream->runtime) {
+		rtd = adata->i2ssp_capture_stream->runtime->private_data;
+		config_acp5x_dma(rtd, SNDRV_PCM_STREAM_CAPTURE);
+		acp_writel((rtd->xfer_resolution  << 3), rtd->acp5x_base + ACP_I2STDM_IRER);
+		if (adata->tdm_mode == TDM_ENABLE) {
+			acp_writel(adata->tdm_fmt, adata->acp5x_base + ACP_I2STDM_RXFRMT);
+			val = acp_readl(adata->acp5x_base + ACP_I2STDM_IRER);
+			acp_writel(val | 0x2, adata->acp5x_base + ACP_I2STDM_IRER);
+		}
 	}
 	acp_writel(1, adata->acp5x_base + ACP_EXTERNAL_INTR_ENB);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/yc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/yc/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0+
+# Yellow Carp platform Support
+snd-pci-acp6x-objs	:= pci-acp6x.o
+snd-acp6x-pdm-dma-objs	:= acp6x-pdm-dma.o
+snd-soc-acp6x-mach-objs := acp6x-mach.o
+
+obj-$(CONFIG_SND_SOC_AMD_ACP6x) += snd-pci-acp6x.o
+obj-$(CONFIG_SND_SOC_AMD_ACP6x) += snd-acp6x-pdm-dma.o
+obj-$(CONFIG_SND_SOC_AMD_YC_MACH)   += snd-soc-acp6x-mach.o
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/yc/acp6x-mach.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/yc/acp6x-mach.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Machine driver for AMD Yellow Carp platform using DMIC
+ *
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ */
+
+#include <sound/soc.h>
+#include <sound/soc-dapm.h>
+#include <linux/module.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <linux/io.h>
+#include <linux/dmi.h>
+#include <linux/acpi.h>
+
+#include "acp6x.h"
+
+#define DRV_NAME "acp_yc_mach"
+
+SND_SOC_DAILINK_DEF(acp6x_pdm,
+		    DAILINK_COMP_ARRAY(COMP_CPU("acp_yc_pdm_dma.0")));
+
+SND_SOC_DAILINK_DEF(dmic_codec,
+		    DAILINK_COMP_ARRAY(COMP_CODEC("dmic-codec.0",
+						  "dmic-hifi")));
+
+SND_SOC_DAILINK_DEF(pdm_platform,
+		    DAILINK_COMP_ARRAY(COMP_PLATFORM("acp_yc_pdm_dma.0")));
+
+static struct snd_soc_dai_link acp6x_dai_pdm[] = {
+	{
+		.name = "acp6x-dmic-capture",
+		.stream_name = "DMIC capture",
+		.capture_only = 1,
+		SND_SOC_DAILINK_REG(acp6x_pdm, dmic_codec, pdm_platform),
+	},
+};
+
+static struct snd_soc_card acp6x_card = {
+	.name = "acp6x",
+	.owner = THIS_MODULE,
+	.dai_link = acp6x_dai_pdm,
+	.num_links = 1,
+};
+
+static const struct dmi_system_id yc_acp_quirk_table[] = {
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21D2"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21D3"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21D4"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21D5"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CF"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CG"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CQ"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CR"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21AW"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21AX"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21BN"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21BQ"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CH"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CJ"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CK"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21CL"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21D8"),
+		}
+	},
+	{
+		.driver_data = &acp6x_card,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "21D9"),
+		}
+	},
+	{}
+};
+
+static int acp6x_probe(struct platform_device *pdev)
+{
+	const struct dmi_system_id *dmi_id;
+	struct acp6x_pdm *machine = NULL;
+	struct snd_soc_card *card;
+	struct acpi_device *adev;
+	int ret;
+
+	/* check the parent device's firmware node has _DSD or not */
+	adev = ACPI_COMPANION(pdev->dev.parent);
+	if (adev) {
+		const union acpi_object *obj;
+
+		if (!acpi_dev_get_property(adev, "AcpDmicConnected", ACPI_TYPE_INTEGER, &obj) &&
+		    obj->integer.value == 1)
+			platform_set_drvdata(pdev, &acp6x_card);
+	}
+
+	/* check for any DMI overrides */
+	dmi_id = dmi_first_match(yc_acp_quirk_table);
+	if (dmi_id)
+		platform_set_drvdata(pdev, dmi_id->driver_data);
+
+	card = platform_get_drvdata(pdev);
+	if (!card)
+		return -ENODEV;
+	dev_info(&pdev->dev, "Enabling ACP DMIC support via %s", dmi_id ? "DMI" : "ACPI");
+	acp6x_card.dev = &pdev->dev;
+
+	snd_soc_card_set_drvdata(card, machine);
+	ret = devm_snd_soc_register_card(&pdev->dev, card);
+	if (ret) {
+		return dev_err_probe(&pdev->dev, ret,
+				"snd_soc_register_card(%s) failed\n",
+				card->name);
+	}
+	return 0;
+}
+
+static struct platform_driver acp6x_mach_driver = {
+	.driver = {
+		.name = "acp_yc_mach",
+		.pm = &snd_soc_pm_ops,
+	},
+	.probe = acp6x_probe,
+};
+
+module_platform_driver(acp6x_mach_driver);
+
+MODULE_AUTHOR("Vijendar.Mukunda@amd.com");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:" DRV_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/yc/acp6x-pdm-dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/yc/acp6x-pdm-dma.c
@@ -0,0 +1,448 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * AMD ALSA SoC Yellow Carp PDM Driver
+ *
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/soc-dai.h>
+#include <linux/pm_runtime.h>
+
+#include "acp6x.h"
+
+#define DRV_NAME "acp_yc_pdm_dma"
+
+static const struct snd_pcm_hardware acp6x_pdm_hardware_capture = {
+	.info = SNDRV_PCM_INFO_INTERLEAVED |
+		SNDRV_PCM_INFO_BLOCK_TRANSFER |
+		SNDRV_PCM_INFO_MMAP |
+		SNDRV_PCM_INFO_MMAP_VALID |
+		SNDRV_PCM_INFO_PAUSE | SNDRV_PCM_INFO_RESUME,
+	.formats = SNDRV_PCM_FMTBIT_S32_LE,
+	.channels_min = 2,
+	.channels_max = 2,
+	.rates = SNDRV_PCM_RATE_48000,
+	.rate_min = 48000,
+	.rate_max = 48000,
+	.buffer_bytes_max = CAPTURE_MAX_NUM_PERIODS * CAPTURE_MAX_PERIOD_SIZE,
+	.period_bytes_min = CAPTURE_MIN_PERIOD_SIZE,
+	.period_bytes_max = CAPTURE_MAX_PERIOD_SIZE,
+	.periods_min = CAPTURE_MIN_NUM_PERIODS,
+	.periods_max = CAPTURE_MAX_NUM_PERIODS,
+};
+
+static void acp6x_init_pdm_ring_buffer(u32 physical_addr, u32 buffer_size,
+				       u32 watermark_size, void __iomem *acp_base)
+{
+	acp6x_writel(physical_addr, acp_base + ACP_WOV_RX_RINGBUFADDR);
+	acp6x_writel(buffer_size, acp_base + ACP_WOV_RX_RINGBUFSIZE);
+	acp6x_writel(watermark_size, acp_base + ACP_WOV_RX_INTR_WATERMARK_SIZE);
+	acp6x_writel(0x01, acp_base + ACPAXI2AXI_ATU_CTRL);
+}
+
+static void acp6x_enable_pdm_clock(void __iomem *acp_base)
+{
+	u32 pdm_clk_enable, pdm_ctrl;
+
+	pdm_clk_enable = ACP_PDM_CLK_FREQ_MASK;
+	pdm_ctrl = 0x00;
+
+	acp6x_writel(pdm_clk_enable, acp_base + ACP_WOV_CLK_CTRL);
+	pdm_ctrl = acp6x_readl(acp_base + ACP_WOV_MISC_CTRL);
+	pdm_ctrl |= ACP_WOV_MISC_CTRL_MASK;
+	acp6x_writel(pdm_ctrl, acp_base + ACP_WOV_MISC_CTRL);
+}
+
+static void acp6x_enable_pdm_interrupts(void __iomem *acp_base)
+{
+	u32 ext_int_ctrl;
+
+	ext_int_ctrl = acp6x_readl(acp_base + ACP_EXTERNAL_INTR_CNTL);
+	ext_int_ctrl |= PDM_DMA_INTR_MASK;
+	acp6x_writel(ext_int_ctrl, acp_base + ACP_EXTERNAL_INTR_CNTL);
+}
+
+static void acp6x_disable_pdm_interrupts(void __iomem *acp_base)
+{
+	u32 ext_int_ctrl;
+
+	ext_int_ctrl = acp6x_readl(acp_base + ACP_EXTERNAL_INTR_CNTL);
+	ext_int_ctrl &= ~PDM_DMA_INTR_MASK;
+	acp6x_writel(ext_int_ctrl, acp_base + ACP_EXTERNAL_INTR_CNTL);
+}
+
+static bool acp6x_check_pdm_dma_status(void __iomem *acp_base)
+{
+	bool pdm_dma_status;
+	u32 pdm_enable, pdm_dma_enable;
+
+	pdm_dma_status = false;
+	pdm_enable = acp6x_readl(acp_base + ACP_WOV_PDM_ENABLE);
+	pdm_dma_enable = acp6x_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE);
+	if ((pdm_enable & ACP_PDM_ENABLE) && (pdm_dma_enable & ACP_PDM_DMA_EN_STATUS))
+		pdm_dma_status = true;
+
+	return pdm_dma_status;
+}
+
+static int acp6x_start_pdm_dma(void __iomem *acp_base)
+{
+	u32 pdm_enable;
+	u32 pdm_dma_enable;
+	int timeout;
+
+	pdm_enable = 0x01;
+	pdm_dma_enable  = 0x01;
+
+	acp6x_enable_pdm_clock(acp_base);
+	acp6x_writel(pdm_enable, acp_base + ACP_WOV_PDM_ENABLE);
+	acp6x_writel(pdm_dma_enable, acp_base + ACP_WOV_PDM_DMA_ENABLE);
+	timeout = 0;
+	while (++timeout < ACP_COUNTER) {
+		pdm_dma_enable = acp6x_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE);
+		if ((pdm_dma_enable & 0x02) == ACP_PDM_DMA_EN_STATUS)
+			return 0;
+		udelay(DELAY_US);
+	}
+	return -ETIMEDOUT;
+}
+
+static int acp6x_stop_pdm_dma(void __iomem *acp_base)
+{
+	u32 pdm_enable, pdm_dma_enable;
+	int timeout;
+
+	pdm_enable = 0x00;
+	pdm_dma_enable  = 0x00;
+
+	pdm_enable = acp6x_readl(acp_base + ACP_WOV_PDM_ENABLE);
+	pdm_dma_enable = acp6x_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE);
+	if (pdm_dma_enable & 0x01) {
+		pdm_dma_enable = 0x02;
+		acp6x_writel(pdm_dma_enable, acp_base + ACP_WOV_PDM_DMA_ENABLE);
+		timeout = 0;
+		while (++timeout < ACP_COUNTER) {
+			pdm_dma_enable = acp6x_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE);
+			if ((pdm_dma_enable & 0x02) == 0x00)
+				break;
+			udelay(DELAY_US);
+		}
+		if (timeout == ACP_COUNTER)
+			return -ETIMEDOUT;
+	}
+	if (pdm_enable == ACP_PDM_ENABLE) {
+		pdm_enable = ACP_PDM_DISABLE;
+		acp6x_writel(pdm_enable, acp_base + ACP_WOV_PDM_ENABLE);
+	}
+	acp6x_writel(0x01, acp_base + ACP_WOV_PDM_FIFO_FLUSH);
+	return 0;
+}
+
+static void acp6x_config_dma(struct pdm_stream_instance *rtd, int direction)
+{
+	u16 page_idx;
+	u32 low, high, val;
+	dma_addr_t addr;
+
+	addr = rtd->dma_addr;
+	val = PDM_PTE_OFFSET;
+
+	/* Group Enable */
+	acp6x_writel(ACP_SRAM_PTE_OFFSET | BIT(31), rtd->acp6x_base +
+		     ACPAXI2AXI_ATU_BASE_ADDR_GRP_1);
+	acp6x_writel(PAGE_SIZE_4K_ENABLE, rtd->acp6x_base +
+		     ACPAXI2AXI_ATU_PAGE_SIZE_GRP_1);
+	for (page_idx = 0; page_idx < rtd->num_pages; page_idx++) {
+		/* Load the low address of page int ACP SRAM through SRBM */
+		low = lower_32_bits(addr);
+		high = upper_32_bits(addr);
+
+		acp6x_writel(low, rtd->acp6x_base + ACP_SCRATCH_REG_0 + val);
+		high |= BIT(31);
+		acp6x_writel(high, rtd->acp6x_base + ACP_SCRATCH_REG_0 + val + 4);
+		val += 8;
+		addr += PAGE_SIZE;
+	}
+}
+
+static int acp6x_pdm_dma_open(struct snd_soc_component *component,
+			      struct snd_pcm_substream *substream)
+{
+	struct snd_pcm_runtime *runtime;
+	struct pdm_dev_data *adata;
+	struct pdm_stream_instance *pdm_data;
+	int ret;
+
+	runtime = substream->runtime;
+	adata = dev_get_drvdata(component->dev);
+	pdm_data = kzalloc(sizeof(*pdm_data), GFP_KERNEL);
+	if (!pdm_data)
+		return -EINVAL;
+
+	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
+		runtime->hw = acp6x_pdm_hardware_capture;
+
+	ret = snd_pcm_hw_constraint_integer(runtime,
+					    SNDRV_PCM_HW_PARAM_PERIODS);
+	if (ret < 0) {
+		dev_err(component->dev, "set integer constraint failed\n");
+		kfree(pdm_data);
+		return ret;
+	}
+
+	acp6x_enable_pdm_interrupts(adata->acp6x_base);
+
+	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
+		adata->capture_stream = substream;
+
+	pdm_data->acp6x_base = adata->acp6x_base;
+	runtime->private_data = pdm_data;
+	return ret;
+}
+
+static int acp6x_pdm_dma_hw_params(struct snd_soc_component *component,
+				   struct snd_pcm_substream *substream,
+				   struct snd_pcm_hw_params *params)
+{
+	struct pdm_stream_instance *rtd;
+	size_t size, period_bytes;
+
+	rtd = substream->runtime->private_data;
+	if (!rtd)
+		return -EINVAL;
+	size = params_buffer_bytes(params);
+	period_bytes = params_period_bytes(params);
+	rtd->dma_addr = substream->runtime->dma_addr;
+	rtd->num_pages = (PAGE_ALIGN(size) >> PAGE_SHIFT);
+	acp6x_config_dma(rtd, substream->stream);
+	acp6x_init_pdm_ring_buffer(PDM_MEM_WINDOW_START, size,
+				   period_bytes, rtd->acp6x_base);
+	return 0;
+}
+
+static u64 acp6x_pdm_get_byte_count(struct pdm_stream_instance *rtd,
+				    int direction)
+{
+	union acp_pdm_dma_count byte_count;
+
+	byte_count.bcount.high =
+			acp6x_readl(rtd->acp6x_base + ACP_WOV_RX_LINEARPOSITIONCNTR_HIGH);
+	byte_count.bcount.low =
+			acp6x_readl(rtd->acp6x_base + ACP_WOV_RX_LINEARPOSITIONCNTR_LOW);
+	return byte_count.bytescount;
+}
+
+static snd_pcm_uframes_t acp6x_pdm_dma_pointer(struct snd_soc_component *comp,
+					       struct snd_pcm_substream *stream)
+{
+	struct pdm_stream_instance *rtd;
+	u32 pos, buffersize;
+	u64 bytescount;
+
+	rtd = stream->runtime->private_data;
+	buffersize = frames_to_bytes(stream->runtime,
+				     stream->runtime->buffer_size);
+	bytescount = acp6x_pdm_get_byte_count(rtd, stream->stream);
+	if (bytescount > rtd->bytescount)
+		bytescount -= rtd->bytescount;
+	pos = do_div(bytescount, buffersize);
+	return bytes_to_frames(stream->runtime, pos);
+}
+
+static int acp6x_pdm_dma_new(struct snd_soc_component *component,
+			     struct snd_soc_pcm_runtime *rtd)
+{
+	struct device *parent = component->dev->parent;
+
+	snd_pcm_set_managed_buffer_all(rtd->pcm, SNDRV_DMA_TYPE_DEV,
+				       parent, MIN_BUFFER, MAX_BUFFER);
+	return 0;
+}
+
+static int acp6x_pdm_dma_close(struct snd_soc_component *component,
+			       struct snd_pcm_substream *substream)
+{
+	struct pdm_dev_data *adata = dev_get_drvdata(component->dev);
+
+	acp6x_disable_pdm_interrupts(adata->acp6x_base);
+	adata->capture_stream = NULL;
+	return 0;
+}
+
+static int acp6x_pdm_dai_trigger(struct snd_pcm_substream *substream,
+				 int cmd, struct snd_soc_dai *dai)
+{
+	struct pdm_stream_instance *rtd;
+	int ret;
+	bool pdm_status;
+	unsigned int ch_mask;
+
+	rtd = substream->runtime->private_data;
+	ret = 0;
+	switch (substream->runtime->channels) {
+	case TWO_CH:
+		ch_mask = 0x00;
+		break;
+	default:
+		return -EINVAL;
+	}
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_START:
+	case SNDRV_PCM_TRIGGER_RESUME:
+	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+		acp6x_writel(ch_mask, rtd->acp6x_base + ACP_WOV_PDM_NO_OF_CHANNELS);
+		acp6x_writel(PDM_DECIMATION_FACTOR, rtd->acp6x_base +
+			     ACP_WOV_PDM_DECIMATION_FACTOR);
+		rtd->bytescount = acp6x_pdm_get_byte_count(rtd, substream->stream);
+		pdm_status = acp6x_check_pdm_dma_status(rtd->acp6x_base);
+		if (!pdm_status)
+			ret = acp6x_start_pdm_dma(rtd->acp6x_base);
+		break;
+	case SNDRV_PCM_TRIGGER_STOP:
+	case SNDRV_PCM_TRIGGER_SUSPEND:
+	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+		pdm_status = acp6x_check_pdm_dma_status(rtd->acp6x_base);
+		if (pdm_status)
+			ret = acp6x_stop_pdm_dma(rtd->acp6x_base);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+	return ret;
+}
+
+static struct snd_soc_dai_ops acp6x_pdm_dai_ops = {
+	.trigger   = acp6x_pdm_dai_trigger,
+};
+
+static struct snd_soc_dai_driver acp6x_pdm_dai_driver = {
+	.capture = {
+		.rates = SNDRV_PCM_RATE_48000,
+		.formats = SNDRV_PCM_FMTBIT_S32_LE,
+		.channels_min = 2,
+		.channels_max = 2,
+		.rate_min = 48000,
+		.rate_max = 48000,
+	},
+	.ops = &acp6x_pdm_dai_ops,
+};
+
+static const struct snd_soc_component_driver acp6x_pdm_component = {
+	.name		= DRV_NAME,
+	.open		= acp6x_pdm_dma_open,
+	.close		= acp6x_pdm_dma_close,
+	.hw_params	= acp6x_pdm_dma_hw_params,
+	.pointer	= acp6x_pdm_dma_pointer,
+	.pcm_construct	= acp6x_pdm_dma_new,
+};
+
+static int acp6x_pdm_audio_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct pdm_dev_data *adata;
+	int status;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "IORESOURCE_MEM FAILED\n");
+		return -ENODEV;
+	}
+
+	adata = devm_kzalloc(&pdev->dev, sizeof(*adata), GFP_KERNEL);
+	if (!adata)
+		return -ENOMEM;
+
+	adata->acp6x_base = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+	if (!adata->acp6x_base)
+		return -ENOMEM;
+
+	adata->capture_stream = NULL;
+
+	dev_set_drvdata(&pdev->dev, adata);
+	status = devm_snd_soc_register_component(&pdev->dev,
+						 &acp6x_pdm_component,
+						 &acp6x_pdm_dai_driver, 1);
+	if (status) {
+		dev_err(&pdev->dev, "Fail to register acp pdm dai\n");
+
+		return -ENODEV;
+	}
+	pm_runtime_set_autosuspend_delay(&pdev->dev, ACP_SUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_allow(&pdev->dev);
+	return 0;
+}
+
+static int acp6x_pdm_audio_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+	return 0;
+}
+
+static int __maybe_unused acp6x_pdm_resume(struct device *dev)
+{
+	struct pdm_dev_data *adata;
+	struct snd_pcm_runtime *runtime;
+	struct pdm_stream_instance *rtd;
+	u32 period_bytes, buffer_len;
+
+	adata = dev_get_drvdata(dev);
+	if (adata->capture_stream && adata->capture_stream->runtime) {
+		runtime = adata->capture_stream->runtime;
+		rtd = runtime->private_data;
+		period_bytes = frames_to_bytes(runtime, runtime->period_size);
+		buffer_len = frames_to_bytes(runtime, runtime->buffer_size);
+		acp6x_config_dma(rtd, SNDRV_PCM_STREAM_CAPTURE);
+		acp6x_init_pdm_ring_buffer(PDM_MEM_WINDOW_START, buffer_len,
+					   period_bytes, adata->acp6x_base);
+	}
+	acp6x_enable_pdm_interrupts(adata->acp6x_base);
+	return 0;
+}
+
+static int __maybe_unused acp6x_pdm_suspend(struct device *dev)
+{
+	struct pdm_dev_data *adata;
+
+	adata = dev_get_drvdata(dev);
+	acp6x_disable_pdm_interrupts(adata->acp6x_base);
+	return 0;
+}
+
+static int __maybe_unused acp6x_pdm_runtime_resume(struct device *dev)
+{
+	struct pdm_dev_data *adata;
+
+	adata = dev_get_drvdata(dev);
+	acp6x_enable_pdm_interrupts(adata->acp6x_base);
+	return 0;
+}
+
+static const struct dev_pm_ops acp6x_pdm_pm_ops = {
+	SET_RUNTIME_PM_OPS(acp6x_pdm_suspend, acp6x_pdm_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(acp6x_pdm_suspend, acp6x_pdm_resume)
+};
+
+static struct platform_driver acp6x_pdm_dma_driver = {
+	.probe = acp6x_pdm_audio_probe,
+	.remove = acp6x_pdm_audio_remove,
+	.driver = {
+		.name = "acp_yc_pdm_dma",
+		.pm = &acp6x_pdm_pm_ops,
+	},
+};
+
+module_platform_driver(acp6x_pdm_dma_driver);
+
+MODULE_AUTHOR("Vijendar.Mukunda@amd.com");
+MODULE_DESCRIPTION("AMD ACP6x YC PDM Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:" DRV_NAME);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/yc/acp6x.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/yc/acp6x.h
@@ -0,0 +1,107 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * AMD ALSA SoC PDM Driver
+ *
+ * Copyright (C) 2021 Advanced Micro Devices, Inc. All rights reserved.
+ */
+
+#include "acp6x_chip_offset_byte.h"
+
+#define ACP_DEVICE_ID 0x15E2
+#define ACP6x_PHY_BASE_ADDRESS 0x1240000
+#define ACP6x_REG_START		0x1240000
+#define ACP6x_REG_END		0x1250200
+#define ACP6x_DEVS		3
+#define ACP6x_PDM_MODE		1
+
+#define ACP_SOFT_RESET_SOFTRESET_AUDDONE_MASK	0x00010001
+#define ACP_PGFSM_CNTL_POWER_ON_MASK	1
+#define ACP_PGFSM_CNTL_POWER_OFF_MASK	0
+#define ACP_PGFSM_STATUS_MASK		3
+#define ACP_POWERED_ON			0
+#define ACP_POWER_ON_IN_PROGRESS	1
+#define ACP_POWERED_OFF			2
+#define ACP_POWER_OFF_IN_PROGRESS	3
+
+#define ACP_ERROR_MASK 0x20000000
+#define ACP_EXT_INTR_STAT_CLEAR_MASK 0xFFFFFFFF
+#define PDM_DMA_STAT 0x10
+
+#define PDM_DMA_INTR_MASK	0x10000
+#define ACP_ERROR_STAT	29
+#define PDM_DECIMATION_FACTOR	2
+#define ACP_PDM_CLK_FREQ_MASK	7
+#define ACP_WOV_MISC_CTRL_MASK	0x10
+#define ACP_PDM_ENABLE		1
+#define ACP_PDM_DISABLE		0
+#define ACP_PDM_DMA_EN_STATUS	2
+#define TWO_CH		2
+#define DELAY_US	5
+#define ACP_COUNTER	20000
+
+#define ACP_SRAM_PTE_OFFSET	0x03800000
+#define PAGE_SIZE_4K_ENABLE	2
+#define PDM_PTE_OFFSET		0
+#define PDM_MEM_WINDOW_START	0x4000000
+
+#define CAPTURE_MIN_NUM_PERIODS     4
+#define CAPTURE_MAX_NUM_PERIODS     4
+#define CAPTURE_MAX_PERIOD_SIZE     8192
+#define CAPTURE_MIN_PERIOD_SIZE     4096
+
+#define MAX_BUFFER (CAPTURE_MAX_PERIOD_SIZE * CAPTURE_MAX_NUM_PERIODS)
+#define MIN_BUFFER MAX_BUFFER
+
+/* time in ms for runtime suspend delay */
+#define ACP_SUSPEND_DELAY_MS	2000
+
+enum acp_config {
+	ACP_CONFIG_0 = 0,
+	ACP_CONFIG_1,
+	ACP_CONFIG_2,
+	ACP_CONFIG_3,
+	ACP_CONFIG_4,
+	ACP_CONFIG_5,
+	ACP_CONFIG_6,
+	ACP_CONFIG_7,
+	ACP_CONFIG_8,
+	ACP_CONFIG_9,
+	ACP_CONFIG_10,
+	ACP_CONFIG_11,
+	ACP_CONFIG_12,
+	ACP_CONFIG_13,
+	ACP_CONFIG_14,
+	ACP_CONFIG_15,
+};
+
+struct pdm_dev_data {
+	u32 pdm_irq;
+	void __iomem *acp6x_base;
+	struct snd_pcm_substream *capture_stream;
+};
+
+struct pdm_stream_instance {
+	u16 num_pages;
+	u16 channels;
+	dma_addr_t dma_addr;
+	u64 bytescount;
+	void __iomem *acp6x_base;
+};
+
+union acp_pdm_dma_count {
+	struct {
+	u32 low;
+	u32 high;
+	} bcount;
+	u64 bytescount;
+};
+
+static inline u32 acp6x_readl(void __iomem *base_addr)
+{
+	return readl(base_addr - ACP6x_PHY_BASE_ADDRESS);
+}
+
+static inline void acp6x_writel(u32 val, void __iomem *base_addr)
+{
+	writel(val, base_addr - ACP6x_PHY_BASE_ADDRESS);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/yc/acp6x_chip_offset_byte.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/yc/acp6x_chip_offset_byte.h
@@ -0,0 +1,444 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * AMD ACP 6.x Register Documentation
+ *
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ */
+
+#ifndef _acp6x_OFFSET_HEADER
+#define _acp6x_OFFSET_HEADER
+
+/* Registers from ACP_DMA block */
+#define ACP_DMA_CNTL_0                                0x1240000
+#define ACP_DMA_CNTL_1                                0x1240004
+#define ACP_DMA_CNTL_2                                0x1240008
+#define ACP_DMA_CNTL_3                                0x124000C
+#define ACP_DMA_CNTL_4                                0x1240010
+#define ACP_DMA_CNTL_5                                0x1240014
+#define ACP_DMA_CNTL_6                                0x1240018
+#define ACP_DMA_CNTL_7                                0x124001C
+#define ACP_DMA_DSCR_STRT_IDX_0                       0x1240020
+#define ACP_DMA_DSCR_STRT_IDX_1                       0x1240024
+#define ACP_DMA_DSCR_STRT_IDX_2                       0x1240028
+#define ACP_DMA_DSCR_STRT_IDX_3                       0x124002C
+#define ACP_DMA_DSCR_STRT_IDX_4                       0x1240030
+#define ACP_DMA_DSCR_STRT_IDX_5                       0x1240034
+#define ACP_DMA_DSCR_STRT_IDX_6                       0x1240038
+#define ACP_DMA_DSCR_STRT_IDX_7                       0x124003C
+#define ACP_DMA_DSCR_CNT_0                            0x1240040
+#define ACP_DMA_DSCR_CNT_1                            0x1240044
+#define ACP_DMA_DSCR_CNT_2                            0x1240048
+#define ACP_DMA_DSCR_CNT_3                            0x124004C
+#define ACP_DMA_DSCR_CNT_4                            0x1240050
+#define ACP_DMA_DSCR_CNT_5                            0x1240054
+#define ACP_DMA_DSCR_CNT_6                            0x1240058
+#define ACP_DMA_DSCR_CNT_7                            0x124005C
+#define ACP_DMA_PRIO_0                                0x1240060
+#define ACP_DMA_PRIO_1                                0x1240064
+#define ACP_DMA_PRIO_2                                0x1240068
+#define ACP_DMA_PRIO_3                                0x124006C
+#define ACP_DMA_PRIO_4                                0x1240070
+#define ACP_DMA_PRIO_5                                0x1240074
+#define ACP_DMA_PRIO_6                                0x1240078
+#define ACP_DMA_PRIO_7                                0x124007C
+#define ACP_DMA_CUR_DSCR_0                            0x1240080
+#define ACP_DMA_CUR_DSCR_1                            0x1240084
+#define ACP_DMA_CUR_DSCR_2                            0x1240088
+#define ACP_DMA_CUR_DSCR_3                            0x124008C
+#define ACP_DMA_CUR_DSCR_4                            0x1240090
+#define ACP_DMA_CUR_DSCR_5                            0x1240094
+#define ACP_DMA_CUR_DSCR_6                            0x1240098
+#define ACP_DMA_CUR_DSCR_7                            0x124009C
+#define ACP_DMA_CUR_TRANS_CNT_0                       0x12400A0
+#define ACP_DMA_CUR_TRANS_CNT_1                       0x12400A4
+#define ACP_DMA_CUR_TRANS_CNT_2                       0x12400A8
+#define ACP_DMA_CUR_TRANS_CNT_3                       0x12400AC
+#define ACP_DMA_CUR_TRANS_CNT_4                       0x12400B0
+#define ACP_DMA_CUR_TRANS_CNT_5                       0x12400B4
+#define ACP_DMA_CUR_TRANS_CNT_6                       0x12400B8
+#define ACP_DMA_CUR_TRANS_CNT_7                       0x12400BC
+#define ACP_DMA_ERR_STS_0                             0x12400C0
+#define ACP_DMA_ERR_STS_1                             0x12400C4
+#define ACP_DMA_ERR_STS_2                             0x12400C8
+#define ACP_DMA_ERR_STS_3                             0x12400CC
+#define ACP_DMA_ERR_STS_4                             0x12400D0
+#define ACP_DMA_ERR_STS_5                             0x12400D4
+#define ACP_DMA_ERR_STS_6                             0x12400D8
+#define ACP_DMA_ERR_STS_7                             0x12400DC
+#define ACP_DMA_DESC_BASE_ADDR                        0x12400E0
+#define ACP_DMA_DESC_MAX_NUM_DSCR                     0x12400E4
+#define ACP_DMA_CH_STS                                0x12400E8
+#define ACP_DMA_CH_GROUP                              0x12400EC
+#define ACP_DMA_CH_RST_STS                            0x12400F0
+
+/* Registers from ACP_AXI2AXIATU block */
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_1                0x1240C00
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_1                0x1240C04
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_2                0x1240C08
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_2                0x1240C0C
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_3                0x1240C10
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_3                0x1240C14
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_4                0x1240C18
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_4                0x1240C1C
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_5                0x1240C20
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_5                0x1240C24
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_6                0x1240C28
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_6                0x1240C2C
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_7                0x1240C30
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_7                0x1240C34
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_8                0x1240C38
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_8                0x1240C3C
+#define ACPAXI2AXI_ATU_CTRL                           0x1240C40
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_9                0x1240C44
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_9                0x1240C48
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_10               0x1240C4C
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_10               0x1240C50
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_11               0x1240C54
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_11               0x1240C58
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_12               0x1240C5C
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_12               0x1240C60
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_13               0x1240C64
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_13               0x1240C68
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_14               0x1240C6C
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_14               0x1240C70
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_15               0x1240C74
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_15               0x1240C78
+#define ACPAXI2AXI_ATU_PAGE_SIZE_GRP_16               0x1240C7C
+#define ACPAXI2AXI_ATU_BASE_ADDR_GRP_16               0x1240C80
+
+/* Registers from ACP_CLKRST block */
+#define ACP_SOFT_RESET                                0x1241000
+#define ACP_CONTROL                                   0x1241004
+#define ACP_STATUS                                    0x1241008
+#define ACP_DYNAMIC_CG_MASTER_CONTROL                 0x1241010
+#define ACP_ZSC_DSP_CTRL                              0x1241014
+#define ACP_ZSC_STS                                   0x1241018
+#define ACP_PGFSM_CONTROL                             0x1241024
+#define ACP_PGFSM_STATUS                              0x1241028
+#define ACP_CLKMUX_SEL                                0x124102C
+
+/* Registers from ACP_AON block */
+#define ACP_PME_EN                                    0x1241400
+#define ACP_DEVICE_STATE                              0x1241404
+#define AZ_DEVICE_STATE                               0x1241408
+#define ACP_PIN_CONFIG                                0x1241440
+#define ACP_PAD_PULLUP_CTRL                           0x1241444
+#define ACP_PAD_PULLDOWN_CTRL                         0x1241448
+#define ACP_PAD_DRIVE_STRENGTH_CTRL                   0x124144C
+#define ACP_PAD_SCHMEN_CTRL                           0x1241450
+#define ACP_SW_PAD_KEEPER_EN                          0x1241454
+#define ACP_SW_WAKE_EN                                0x1241458
+#define ACP_I2S_WAKE_EN                               0x124145C
+#define ACP_SW1_WAKE_EN                               0x1241460
+
+/* Registers from ACP_P1_MISC block */
+#define ACP_EXTERNAL_INTR_ENB                         0x1241A00
+#define ACP_EXTERNAL_INTR_CNTL                        0x1241A04
+#define ACP_EXTERNAL_INTR_CNTL1                       0x1241A08
+#define ACP_EXTERNAL_INTR_STAT                        0x1241A0C
+#define ACP_EXTERNAL_INTR_STAT1                       0x1241A10
+#define ACP_ERROR_STATUS                              0x1241A4C
+#define ACP_P1_SW_I2S_ERROR_REASON                    0x1241A50
+#define ACP_P1_SW_POS_TRACK_I2S_TX_CTRL               0x1241A6C
+#define ACP_P1_SW_I2S_TX_DMA_POS                      0x1241A70
+#define ACP_P1_SW_POS_TRACK_I2S_RX_CTRL               0x1241A74
+#define ACP_P1_SW_I2S_RX_DMA_POS                      0x1241A78
+#define ACP_P1_DMIC_I2S_GPIO_INTR_CTRL                0x1241A7C
+#define ACP_P1_DMIC_I2S_GPIO_INTR_STATUS              0x1241A80
+#define ACP_SCRATCH_REG_BASE_ADDR                     0x1241A84
+#define ACP_P1_SW_POS_TRACK_BT_TX_CTRL                0x1241A88
+#define ACP_P1_SW_BT_TX_DMA_POS                       0x1241A8C
+#define ACP_P1_SW_POS_TRACK_HS_TX_CTRL                0x1241A90
+#define ACP_P1_SW_HS_TX_DMA_POS                       0x1241A94
+#define ACP_P1_SW_POS_TRACK_BT_RX_CTRL                0x1241A98
+#define ACP_P1_SW_BT_RX_DMA_POS                       0x1241A9C
+#define ACP_P1_SW_POS_TRACK_HS_RX_CTRL                0x1241AA0
+#define ACP_P1_SW_HS_RX_DMA_POS                       0x1241AA4
+
+/* Registers from ACP_AUDIO_BUFFERS block */
+#define ACP_I2S_RX_RINGBUFADDR                        0x1242000
+#define ACP_I2S_RX_RINGBUFSIZE                        0x1242004
+#define ACP_I2S_RX_LINKPOSITIONCNTR                   0x1242008
+#define ACP_I2S_RX_FIFOADDR                           0x124200C
+#define ACP_I2S_RX_FIFOSIZE                           0x1242010
+#define ACP_I2S_RX_DMA_SIZE                           0x1242014
+#define ACP_I2S_RX_LINEARPOSITIONCNTR_HIGH            0x1242018
+#define ACP_I2S_RX_LINEARPOSITIONCNTR_LOW             0x124201C
+#define ACP_I2S_RX_INTR_WATERMARK_SIZE                0x1242020
+#define ACP_I2S_TX_RINGBUFADDR                        0x1242024
+#define ACP_I2S_TX_RINGBUFSIZE                        0x1242028
+#define ACP_I2S_TX_LINKPOSITIONCNTR                   0x124202C
+#define ACP_I2S_TX_FIFOADDR                           0x1242030
+#define ACP_I2S_TX_FIFOSIZE                           0x1242034
+#define ACP_I2S_TX_DMA_SIZE                           0x1242038
+#define ACP_I2S_TX_LINEARPOSITIONCNTR_HIGH            0x124203C
+#define ACP_I2S_TX_LINEARPOSITIONCNTR_LOW             0x1242040
+#define ACP_I2S_TX_INTR_WATERMARK_SIZE                0x1242044
+#define ACP_BT_RX_RINGBUFADDR                         0x1242048
+#define ACP_BT_RX_RINGBUFSIZE                         0x124204C
+#define ACP_BT_RX_LINKPOSITIONCNTR                    0x1242050
+#define ACP_BT_RX_FIFOADDR                            0x1242054
+#define ACP_BT_RX_FIFOSIZE                            0x1242058
+#define ACP_BT_RX_DMA_SIZE                            0x124205C
+#define ACP_BT_RX_LINEARPOSITIONCNTR_HIGH             0x1242060
+#define ACP_BT_RX_LINEARPOSITIONCNTR_LOW              0x1242064
+#define ACP_BT_RX_INTR_WATERMARK_SIZE                 0x1242068
+#define ACP_BT_TX_RINGBUFADDR                         0x124206C
+#define ACP_BT_TX_RINGBUFSIZE                         0x1242070
+#define ACP_BT_TX_LINKPOSITIONCNTR                    0x1242074
+#define ACP_BT_TX_FIFOADDR                            0x1242078
+#define ACP_BT_TX_FIFOSIZE                            0x124207C
+#define ACP_BT_TX_DMA_SIZE                            0x1242080
+#define ACP_BT_TX_LINEARPOSITIONCNTR_HIGH             0x1242084
+#define ACP_BT_TX_LINEARPOSITIONCNTR_LOW              0x1242088
+#define ACP_BT_TX_INTR_WATERMARK_SIZE                 0x124208C
+#define ACP_HS_RX_RINGBUFADDR                         0x1242090
+#define ACP_HS_RX_RINGBUFSIZE                         0x1242094
+#define ACP_HS_RX_LINKPOSITIONCNTR                    0x1242098
+#define ACP_HS_RX_FIFOADDR                            0x124209C
+#define ACP_HS_RX_FIFOSIZE                            0x12420A0
+#define ACP_HS_RX_DMA_SIZE                            0x12420A4
+#define ACP_HS_RX_LINEARPOSITIONCNTR_HIGH             0x12420A8
+#define ACP_HS_RX_LINEARPOSITIONCNTR_LOW              0x12420AC
+#define ACP_HS_RX_INTR_WATERMARK_SIZE                 0x12420B0
+#define ACP_HS_TX_RINGBUFADDR                         0x12420B4
+#define ACP_HS_TX_RINGBUFSIZE                         0x12420B8
+#define ACP_HS_TX_LINKPOSITIONCNTR                    0x12420BC
+#define ACP_HS_TX_FIFOADDR                            0x12420C0
+#define ACP_HS_TX_FIFOSIZE                            0x12420C4
+#define ACP_HS_TX_DMA_SIZE                            0x12420C8
+#define ACP_HS_TX_LINEARPOSITIONCNTR_HIGH             0x12420CC
+#define ACP_HS_TX_LINEARPOSITIONCNTR_LOW              0x12420D0
+#define ACP_HS_TX_INTR_WATERMARK_SIZE                 0x12420D4
+
+/* Registers from ACP_I2S_TDM block */
+#define ACP_I2STDM_IER                                0x1242400
+#define ACP_I2STDM_IRER                               0x1242404
+#define ACP_I2STDM_RXFRMT                             0x1242408
+#define ACP_I2STDM_ITER                               0x124240C
+#define ACP_I2STDM_TXFRMT                             0x1242410
+#define ACP_I2STDM0_MSTRCLKGEN                        0x1242414
+#define ACP_I2STDM1_MSTRCLKGEN                        0x1242418
+#define ACP_I2STDM2_MSTRCLKGEN                        0x124241C
+#define ACP_I2STDM_REFCLKGEN                          0x1242420
+
+/* Registers from ACP_BT_TDM block */
+#define ACP_BTTDM_IER                                 0x1242800
+#define ACP_BTTDM_IRER                                0x1242804
+#define ACP_BTTDM_RXFRMT                              0x1242808
+#define ACP_BTTDM_ITER                                0x124280C
+#define ACP_BTTDM_TXFRMT                              0x1242810
+#define ACP_HSTDM_IER                                 0x1242814
+#define ACP_HSTDM_IRER                                0x1242818
+#define ACP_HSTDM_RXFRMT                              0x124281C
+#define ACP_HSTDM_ITER                                0x1242820
+#define ACP_HSTDM_TXFRMT                              0x1242824
+
+/* Registers from ACP_WOV block */
+#define ACP_WOV_PDM_ENABLE                            0x1242C04
+#define ACP_WOV_PDM_DMA_ENABLE                        0x1242C08
+#define ACP_WOV_RX_RINGBUFADDR                        0x1242C0C
+#define ACP_WOV_RX_RINGBUFSIZE                        0x1242C10
+#define ACP_WOV_RX_LINKPOSITIONCNTR                   0x1242C14
+#define ACP_WOV_RX_LINEARPOSITIONCNTR_HIGH            0x1242C18
+#define ACP_WOV_RX_LINEARPOSITIONCNTR_LOW             0x1242C1C
+#define ACP_WOV_RX_INTR_WATERMARK_SIZE                0x1242C20
+#define ACP_WOV_PDM_FIFO_FLUSH                        0x1242C24
+#define ACP_WOV_PDM_NO_OF_CHANNELS                    0x1242C28
+#define ACP_WOV_PDM_DECIMATION_FACTOR                 0x1242C2C
+#define ACP_WOV_PDM_VAD_CTRL                          0x1242C30
+#define ACP_WOV_WAKE                                  0x1242C54
+#define ACP_WOV_BUFFER_STATUS                         0x1242C58
+#define ACP_WOV_MISC_CTRL                             0x1242C5C
+#define ACP_WOV_CLK_CTRL                              0x1242C60
+#define ACP_PDM_VAD_DYNAMIC_CLK_GATING_EN             0x1242C64
+#define ACP_WOV_ERROR_STATUS_REGISTER                 0x1242C68
+#define ACP_PDM_CLKDIV                                0x1242C6C
+
+/* Registers from ACP_P1_AUDIO_BUFFERS block */
+#define ACP_P1_I2S_RX_RINGBUFADDR                     0x1243A00
+#define ACP_P1_I2S_RX_RINGBUFSIZE                     0x1243A04
+#define ACP_P1_I2S_RX_LINKPOSITIONCNTR                0x1243A08
+#define ACP_P1_I2S_RX_FIFOADDR                        0x1243A0C
+#define ACP_P1_I2S_RX_FIFOSIZE                        0x1243A10
+#define ACP_P1_I2S_RX_DMA_SIZE                        0x1243A14
+#define ACP_P1_I2S_RX_LINEARPOSITIONCNTR_HIGH         0x1243A18
+#define ACP_P1_I2S_RX_LINEARPOSITIONCNTR_LOW          0x1243A1C
+#define ACP_P1_I2S_RX_INTR_WATERMARK_SIZE             0x1243A20
+#define ACP_P1_I2S_TX_RINGBUFADDR                     0x1243A24
+#define ACP_P1_I2S_TX_RINGBUFSIZE                     0x1243A28
+#define ACP_P1_I2S_TX_LINKPOSITIONCNTR                0x1243A2C
+#define ACP_P1_I2S_TX_FIFOADDR                        0x1243A30
+#define ACP_P1_I2S_TX_FIFOSIZE                        0x1243A34
+#define ACP_P1_I2S_TX_DMA_SIZE                        0x1243A38
+#define ACP_P1_I2S_TX_LINEARPOSITIONCNTR_HIGH         0x1243A3C
+#define ACP_P1_I2S_TX_LINEARPOSITIONCNTR_LOW          0x1243A40
+#define ACP_P1_I2S_TX_INTR_WATERMARK_SIZE             0x1243A44
+#define ACP_P1_BT_RX_RINGBUFADDR                      0x1243A48
+#define ACP_P1_BT_RX_RINGBUFSIZE                      0x1243A4C
+#define ACP_P1_BT_RX_LINKPOSITIONCNTR                 0x1243A50
+#define ACP_P1_BT_RX_FIFOADDR                         0x1243A54
+#define ACP_P1_BT_RX_FIFOSIZE                         0x1243A58
+#define ACP_P1_BT_RX_DMA_SIZE                         0x1243A5C
+#define ACP_P1_BT_RX_LINEARPOSITIONCNTR_HIGH          0x1243A60
+#define ACP_P1_BT_RX_LINEARPOSITIONCNTR_LOW           0x1243A64
+#define ACP_P1_BT_RX_INTR_WATERMARK_SIZE              0x1243A68
+#define ACP_P1_BT_TX_RINGBUFADDR                      0x1243A6C
+#define ACP_P1_BT_TX_RINGBUFSIZE                      0x1243A70
+#define ACP_P1_BT_TX_LINKPOSITIONCNTR                 0x1243A74
+#define ACP_P1_BT_TX_FIFOADDR                         0x1243A78
+#define ACP_P1_BT_TX_FIFOSIZE                         0x1243A7C
+#define ACP_P1_BT_TX_DMA_SIZE                         0x1243A80
+#define ACP_P1_BT_TX_LINEARPOSITIONCNTR_HIGH          0x1243A84
+#define ACP_P1_BT_TX_LINEARPOSITIONCNTR_LOW           0x1243A88
+#define ACP_P1_BT_TX_INTR_WATERMARK_SIZE              0x1243A8C
+#define ACP_P1_HS_RX_RINGBUFADDR                      0x1243A90
+#define ACP_P1_HS_RX_RINGBUFSIZE                      0x1243A94
+#define ACP_P1_HS_RX_LINKPOSITIONCNTR                 0x1243A98
+#define ACP_P1_HS_RX_FIFOADDR                         0x1243A9C
+#define ACP_P1_HS_RX_FIFOSIZE                         0x1243AA0
+#define ACP_P1_HS_RX_DMA_SIZE                         0x1243AA4
+#define ACP_P1_HS_RX_LINEARPOSITIONCNTR_HIGH          0x1243AA8
+#define ACP_P1_HS_RX_LINEARPOSITIONCNTR_LOW           0x1243AAC
+#define ACP_P1_HS_RX_INTR_WATERMARK_SIZE              0x1243AB0
+#define ACP_P1_HS_TX_RINGBUFADDR                      0x1243AB4
+#define ACP_P1_HS_TX_RINGBUFSIZE                      0x1243AB8
+#define ACP_P1_HS_TX_LINKPOSITIONCNTR                 0x1243ABC
+#define ACP_P1_HS_TX_FIFOADDR                         0x1243AC0
+#define ACP_P1_HS_TX_FIFOSIZE                         0x1243AC4
+#define ACP_P1_HS_TX_DMA_SIZE                         0x1243AC8
+#define ACP_P1_HS_TX_LINEARPOSITIONCNTR_HIGH          0x1243ACC
+#define ACP_P1_HS_TX_LINEARPOSITIONCNTR_LOW           0x1243AD0
+#define ACP_P1_HS_TX_INTR_WATERMARK_SIZE              0x1243AD4
+
+/* Registers from ACP_SCRATCH block */
+#define ACP_SCRATCH_REG_0                             0x1250000
+#define ACP_SCRATCH_REG_1                             0x1250004
+#define ACP_SCRATCH_REG_2                             0x1250008
+#define ACP_SCRATCH_REG_3                             0x125000C
+#define ACP_SCRATCH_REG_4                             0x1250010
+#define ACP_SCRATCH_REG_5                             0x1250014
+#define ACP_SCRATCH_REG_6                             0x1250018
+#define ACP_SCRATCH_REG_7                             0x125001C
+#define ACP_SCRATCH_REG_8                             0x1250020
+#define ACP_SCRATCH_REG_9                             0x1250024
+#define ACP_SCRATCH_REG_10                            0x1250028
+#define ACP_SCRATCH_REG_11                            0x125002C
+#define ACP_SCRATCH_REG_12                            0x1250030
+#define ACP_SCRATCH_REG_13                            0x1250034
+#define ACP_SCRATCH_REG_14                            0x1250038
+#define ACP_SCRATCH_REG_15                            0x125003C
+#define ACP_SCRATCH_REG_16                            0x1250040
+#define ACP_SCRATCH_REG_17                            0x1250044
+#define ACP_SCRATCH_REG_18                            0x1250048
+#define ACP_SCRATCH_REG_19                            0x125004C
+#define ACP_SCRATCH_REG_20                            0x1250050
+#define ACP_SCRATCH_REG_21                            0x1250054
+#define ACP_SCRATCH_REG_22                            0x1250058
+#define ACP_SCRATCH_REG_23                            0x125005C
+#define ACP_SCRATCH_REG_24                            0x1250060
+#define ACP_SCRATCH_REG_25                            0x1250064
+#define ACP_SCRATCH_REG_26                            0x1250068
+#define ACP_SCRATCH_REG_27                            0x125006C
+#define ACP_SCRATCH_REG_28                            0x1250070
+#define ACP_SCRATCH_REG_29                            0x1250074
+#define ACP_SCRATCH_REG_30                            0x1250078
+#define ACP_SCRATCH_REG_31                            0x125007C
+#define ACP_SCRATCH_REG_32                            0x1250080
+#define ACP_SCRATCH_REG_33                            0x1250084
+#define ACP_SCRATCH_REG_34                            0x1250088
+#define ACP_SCRATCH_REG_35                            0x125008C
+#define ACP_SCRATCH_REG_36                            0x1250090
+#define ACP_SCRATCH_REG_37                            0x1250094
+#define ACP_SCRATCH_REG_38                            0x1250098
+#define ACP_SCRATCH_REG_39                            0x125009C
+#define ACP_SCRATCH_REG_40                            0x12500A0
+#define ACP_SCRATCH_REG_41                            0x12500A4
+#define ACP_SCRATCH_REG_42                            0x12500A8
+#define ACP_SCRATCH_REG_43                            0x12500AC
+#define ACP_SCRATCH_REG_44                            0x12500B0
+#define ACP_SCRATCH_REG_45                            0x12500B4
+#define ACP_SCRATCH_REG_46                            0x12500B8
+#define ACP_SCRATCH_REG_47                            0x12500BC
+#define ACP_SCRATCH_REG_48                            0x12500C0
+#define ACP_SCRATCH_REG_49                            0x12500C4
+#define ACP_SCRATCH_REG_50                            0x12500C8
+#define ACP_SCRATCH_REG_51                            0x12500CC
+#define ACP_SCRATCH_REG_52                            0x12500D0
+#define ACP_SCRATCH_REG_53                            0x12500D4
+#define ACP_SCRATCH_REG_54                            0x12500D8
+#define ACP_SCRATCH_REG_55                            0x12500DC
+#define ACP_SCRATCH_REG_56                            0x12500E0
+#define ACP_SCRATCH_REG_57                            0x12500E4
+#define ACP_SCRATCH_REG_58                            0x12500E8
+#define ACP_SCRATCH_REG_59                            0x12500EC
+#define ACP_SCRATCH_REG_60                            0x12500F0
+#define ACP_SCRATCH_REG_61                            0x12500F4
+#define ACP_SCRATCH_REG_62                            0x12500F8
+#define ACP_SCRATCH_REG_63                            0x12500FC
+#define ACP_SCRATCH_REG_64                            0x1250100
+#define ACP_SCRATCH_REG_65                            0x1250104
+#define ACP_SCRATCH_REG_66                            0x1250108
+#define ACP_SCRATCH_REG_67                            0x125010C
+#define ACP_SCRATCH_REG_68                            0x1250110
+#define ACP_SCRATCH_REG_69                            0x1250114
+#define ACP_SCRATCH_REG_70                            0x1250118
+#define ACP_SCRATCH_REG_71                            0x125011C
+#define ACP_SCRATCH_REG_72                            0x1250120
+#define ACP_SCRATCH_REG_73                            0x1250124
+#define ACP_SCRATCH_REG_74                            0x1250128
+#define ACP_SCRATCH_REG_75                            0x125012C
+#define ACP_SCRATCH_REG_76                            0x1250130
+#define ACP_SCRATCH_REG_77                            0x1250134
+#define ACP_SCRATCH_REG_78                            0x1250138
+#define ACP_SCRATCH_REG_79                            0x125013C
+#define ACP_SCRATCH_REG_80                            0x1250140
+#define ACP_SCRATCH_REG_81                            0x1250144
+#define ACP_SCRATCH_REG_82                            0x1250148
+#define ACP_SCRATCH_REG_83                            0x125014C
+#define ACP_SCRATCH_REG_84                            0x1250150
+#define ACP_SCRATCH_REG_85                            0x1250154
+#define ACP_SCRATCH_REG_86                            0x1250158
+#define ACP_SCRATCH_REG_87                            0x125015C
+#define ACP_SCRATCH_REG_88                            0x1250160
+#define ACP_SCRATCH_REG_89                            0x1250164
+#define ACP_SCRATCH_REG_90                            0x1250168
+#define ACP_SCRATCH_REG_91                            0x125016C
+#define ACP_SCRATCH_REG_92                            0x1250170
+#define ACP_SCRATCH_REG_93                            0x1250174
+#define ACP_SCRATCH_REG_94                            0x1250178
+#define ACP_SCRATCH_REG_95                            0x125017C
+#define ACP_SCRATCH_REG_96                            0x1250180
+#define ACP_SCRATCH_REG_97                            0x1250184
+#define ACP_SCRATCH_REG_98                            0x1250188
+#define ACP_SCRATCH_REG_99                            0x125018C
+#define ACP_SCRATCH_REG_100                           0x1250190
+#define ACP_SCRATCH_REG_101                           0x1250194
+#define ACP_SCRATCH_REG_102                           0x1250198
+#define ACP_SCRATCH_REG_103                           0x125019C
+#define ACP_SCRATCH_REG_104                           0x12501A0
+#define ACP_SCRATCH_REG_105                           0x12501A4
+#define ACP_SCRATCH_REG_106                           0x12501A8
+#define ACP_SCRATCH_REG_107                           0x12501AC
+#define ACP_SCRATCH_REG_108                           0x12501B0
+#define ACP_SCRATCH_REG_109                           0x12501B4
+#define ACP_SCRATCH_REG_110                           0x12501B8
+#define ACP_SCRATCH_REG_111                           0x12501BC
+#define ACP_SCRATCH_REG_112                           0x12501C0
+#define ACP_SCRATCH_REG_113                           0x12501C4
+#define ACP_SCRATCH_REG_114                           0x12501C8
+#define ACP_SCRATCH_REG_115                           0x12501CC
+#define ACP_SCRATCH_REG_116                           0x12501D0
+#define ACP_SCRATCH_REG_117                           0x12501D4
+#define ACP_SCRATCH_REG_118                           0x12501D8
+#define ACP_SCRATCH_REG_119                           0x12501DC
+#define ACP_SCRATCH_REG_120                           0x12501E0
+#define ACP_SCRATCH_REG_121                           0x12501E4
+#define ACP_SCRATCH_REG_122                           0x12501E8
+#define ACP_SCRATCH_REG_123                           0x12501EC
+#define ACP_SCRATCH_REG_124                           0x12501F0
+#define ACP_SCRATCH_REG_125                           0x12501F4
+#define ACP_SCRATCH_REG_126                           0x12501F8
+#define ACP_SCRATCH_REG_127                           0x12501FC
+#define ACP_SCRATCH_REG_128                           0x1250200
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/amd/yc/pci-acp6x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/amd/yc/pci-acp6x.c
@@ -0,0 +1,339 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * AMD Yellow Carp ACP PCI Driver
+ *
+ * Copyright 2021 Advanced Micro Devices, Inc.
+ */
+
+#include <linux/pci.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <sound/pcm_params.h>
+#include <linux/pm_runtime.h>
+
+#include "acp6x.h"
+
+struct acp6x_dev_data {
+	void __iomem *acp6x_base;
+	struct resource *res;
+	bool acp6x_audio_mode;
+	struct platform_device *pdev[ACP6x_DEVS];
+};
+
+static int acp6x_power_on(void __iomem *acp_base)
+{
+	u32 val;
+	int timeout;
+
+	val = acp6x_readl(acp_base + ACP_PGFSM_STATUS);
+
+	if (!val)
+		return val;
+
+	if ((val & ACP_PGFSM_STATUS_MASK) != ACP_POWER_ON_IN_PROGRESS)
+		acp6x_writel(ACP_PGFSM_CNTL_POWER_ON_MASK, acp_base + ACP_PGFSM_CONTROL);
+	timeout = 0;
+	while (++timeout < 500) {
+		val = acp6x_readl(acp_base + ACP_PGFSM_STATUS);
+		if (!val)
+			return 0;
+		udelay(1);
+	}
+	return -ETIMEDOUT;
+}
+
+static int acp6x_reset(void __iomem *acp_base)
+{
+	u32 val;
+	int timeout;
+
+	acp6x_writel(1, acp_base + ACP_SOFT_RESET);
+	timeout = 0;
+	while (++timeout < 500) {
+		val = acp6x_readl(acp_base + ACP_SOFT_RESET);
+		if (val & ACP_SOFT_RESET_SOFTRESET_AUDDONE_MASK)
+			break;
+		cpu_relax();
+	}
+	acp6x_writel(0, acp_base + ACP_SOFT_RESET);
+	timeout = 0;
+	while (++timeout < 500) {
+		val = acp6x_readl(acp_base + ACP_SOFT_RESET);
+		if (!val)
+			return 0;
+		cpu_relax();
+	}
+	return -ETIMEDOUT;
+}
+
+static void acp6x_enable_interrupts(void __iomem *acp_base)
+{
+	acp6x_writel(0x01, acp_base + ACP_EXTERNAL_INTR_ENB);
+}
+
+static void acp6x_disable_interrupts(void __iomem *acp_base)
+{
+	acp6x_writel(ACP_EXT_INTR_STAT_CLEAR_MASK, acp_base +
+		     ACP_EXTERNAL_INTR_STAT);
+	acp6x_writel(0x00, acp_base + ACP_EXTERNAL_INTR_CNTL);
+	acp6x_writel(0x00, acp_base + ACP_EXTERNAL_INTR_ENB);
+}
+
+static int acp6x_init(void __iomem *acp_base)
+{
+	int ret;
+
+	/* power on */
+	ret = acp6x_power_on(acp_base);
+	if (ret) {
+		pr_err("ACP power on failed\n");
+		return ret;
+	}
+	acp6x_writel(0x01, acp_base + ACP_CONTROL);
+	/* Reset */
+	ret = acp6x_reset(acp_base);
+	if (ret) {
+		pr_err("ACP reset failed\n");
+		return ret;
+	}
+	acp6x_writel(0x03, acp_base + ACP_CLKMUX_SEL);
+	acp6x_enable_interrupts(acp_base);
+	return 0;
+}
+
+static int acp6x_deinit(void __iomem *acp_base)
+{
+	int ret;
+
+	acp6x_disable_interrupts(acp_base);
+	/* Reset */
+	ret = acp6x_reset(acp_base);
+	if (ret) {
+		pr_err("ACP reset failed\n");
+		return ret;
+	}
+	acp6x_writel(0x00, acp_base + ACP_CLKMUX_SEL);
+	acp6x_writel(0x00, acp_base + ACP_CONTROL);
+	return 0;
+}
+
+static irqreturn_t acp6x_irq_handler(int irq, void *dev_id)
+{
+	struct acp6x_dev_data *adata;
+	struct pdm_dev_data *yc_pdm_data;
+	u32 val;
+
+	adata = dev_id;
+	if (!adata)
+		return IRQ_NONE;
+
+	val = acp6x_readl(adata->acp6x_base + ACP_EXTERNAL_INTR_STAT);
+	if (val & BIT(PDM_DMA_STAT)) {
+		yc_pdm_data = dev_get_drvdata(&adata->pdev[0]->dev);
+		acp6x_writel(BIT(PDM_DMA_STAT), adata->acp6x_base + ACP_EXTERNAL_INTR_STAT);
+		if (yc_pdm_data->capture_stream)
+			snd_pcm_period_elapsed(yc_pdm_data->capture_stream);
+		return IRQ_HANDLED;
+	}
+	return IRQ_NONE;
+}
+
+static int snd_acp6x_probe(struct pci_dev *pci,
+			   const struct pci_device_id *pci_id)
+{
+	struct acp6x_dev_data *adata;
+	struct platform_device_info pdevinfo[ACP6x_DEVS];
+	int index = 0;
+	int val = 0x00;
+	u32 addr;
+	unsigned int irqflags;
+	int ret;
+
+	irqflags = IRQF_SHARED;
+	/* Yellow Carp device check */
+	if (pci->revision != 0x60)
+		return -ENODEV;
+
+	if (pci_enable_device(pci)) {
+		dev_err(&pci->dev, "pci_enable_device failed\n");
+		return -ENODEV;
+	}
+
+	ret = pci_request_regions(pci, "AMD ACP3x audio");
+	if (ret < 0) {
+		dev_err(&pci->dev, "pci_request_regions failed\n");
+		goto disable_pci;
+	}
+
+	adata = devm_kzalloc(&pci->dev, sizeof(struct acp6x_dev_data),
+			     GFP_KERNEL);
+	if (!adata) {
+		ret = -ENOMEM;
+		goto release_regions;
+	}
+
+	addr = pci_resource_start(pci, 0);
+	adata->acp6x_base = devm_ioremap(&pci->dev, addr,
+					 pci_resource_len(pci, 0));
+	if (!adata->acp6x_base) {
+		ret = -ENOMEM;
+		goto release_regions;
+	}
+	pci_set_master(pci);
+	pci_set_drvdata(pci, adata);
+	ret = acp6x_init(adata->acp6x_base);
+	if (ret)
+		goto release_regions;
+	val = acp6x_readl(adata->acp6x_base + ACP_PIN_CONFIG);
+	switch (val) {
+	case ACP_CONFIG_0:
+	case ACP_CONFIG_1:
+	case ACP_CONFIG_2:
+	case ACP_CONFIG_3:
+	case ACP_CONFIG_9:
+	case ACP_CONFIG_15:
+		dev_info(&pci->dev, "Audio Mode %d\n", val);
+		break;
+	default:
+		adata->res = devm_kzalloc(&pci->dev,
+					  sizeof(struct resource),
+					  GFP_KERNEL);
+		if (!adata->res) {
+			ret = -ENOMEM;
+			goto de_init;
+		}
+
+		adata->res->name = "acp_iomem";
+		adata->res->flags = IORESOURCE_MEM;
+		adata->res->start = addr;
+		adata->res->end = addr + (ACP6x_REG_END - ACP6x_REG_START);
+
+		adata->acp6x_audio_mode = ACP6x_PDM_MODE;
+
+		memset(&pdevinfo, 0, sizeof(pdevinfo));
+		pdevinfo[0].name = "acp_yc_pdm_dma";
+		pdevinfo[0].id = 0;
+		pdevinfo[0].parent = &pci->dev;
+		pdevinfo[0].num_res = 1;
+		pdevinfo[0].res = adata->res;
+
+		pdevinfo[1].name = "dmic-codec";
+		pdevinfo[1].id = 0;
+		pdevinfo[1].parent = &pci->dev;
+
+		pdevinfo[2].name = "acp_yc_mach";
+		pdevinfo[2].id = 0;
+		pdevinfo[2].parent = &pci->dev;
+
+		for (index = 0; index < ACP6x_DEVS; index++) {
+			adata->pdev[index] =
+				platform_device_register_full(&pdevinfo[index]);
+			if (IS_ERR(adata->pdev[index])) {
+				dev_err(&pci->dev, "cannot register %s device\n",
+					pdevinfo[index].name);
+				ret = PTR_ERR(adata->pdev[index]);
+				goto unregister_devs;
+			}
+		}
+		break;
+	}
+	ret = devm_request_irq(&pci->dev, pci->irq, acp6x_irq_handler,
+			       irqflags, "ACP_PCI_IRQ", adata);
+	if (ret) {
+		dev_err(&pci->dev, "ACP PCI IRQ request failed\n");
+		goto unregister_devs;
+	}
+	pm_runtime_set_autosuspend_delay(&pci->dev, ACP_SUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(&pci->dev);
+	pm_runtime_put_noidle(&pci->dev);
+	pm_runtime_allow(&pci->dev);
+
+	return 0;
+unregister_devs:
+	for (--index; index >= 0; index--)
+		platform_device_unregister(adata->pdev[index]);
+de_init:
+	if (acp6x_deinit(adata->acp6x_base))
+		dev_err(&pci->dev, "ACP de-init failed\n");
+release_regions:
+	pci_release_regions(pci);
+disable_pci:
+	pci_disable_device(pci);
+
+	return ret;
+}
+
+static int __maybe_unused snd_acp6x_suspend(struct device *dev)
+{
+	struct acp6x_dev_data *adata;
+	int ret;
+
+	adata = dev_get_drvdata(dev);
+	ret = acp6x_deinit(adata->acp6x_base);
+	if (ret)
+		dev_err(dev, "ACP de-init failed\n");
+	return ret;
+}
+
+static int __maybe_unused snd_acp6x_resume(struct device *dev)
+{
+	struct acp6x_dev_data *adata;
+	int ret;
+
+	adata = dev_get_drvdata(dev);
+	ret = acp6x_init(adata->acp6x_base);
+	if (ret)
+		dev_err(dev, "ACP init failed\n");
+	return ret;
+}
+
+static const struct dev_pm_ops acp6x_pm = {
+	SET_RUNTIME_PM_OPS(snd_acp6x_suspend, snd_acp6x_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(snd_acp6x_suspend, snd_acp6x_resume)
+};
+
+static void snd_acp6x_remove(struct pci_dev *pci)
+{
+	struct acp6x_dev_data *adata;
+	int ret, index;
+
+	adata = pci_get_drvdata(pci);
+	if (adata->acp6x_audio_mode == ACP6x_PDM_MODE) {
+		for (index = 0; index < ACP6x_DEVS; index++)
+			platform_device_unregister(adata->pdev[index]);
+	}
+	ret = acp6x_deinit(adata->acp6x_base);
+	if (ret)
+		dev_err(&pci->dev, "ACP de-init failed\n");
+	pm_runtime_forbid(&pci->dev);
+	pm_runtime_get_noresume(&pci->dev);
+	pci_release_regions(pci);
+	pci_disable_device(pci);
+}
+
+static const struct pci_device_id snd_acp6x_ids[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, ACP_DEVICE_ID),
+	.class = PCI_CLASS_MULTIMEDIA_OTHER << 8,
+	.class_mask = 0xffffff },
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, snd_acp6x_ids);
+
+static struct pci_driver yc_acp6x_driver  = {
+	.name = KBUILD_MODNAME,
+	.id_table = snd_acp6x_ids,
+	.probe = snd_acp6x_probe,
+	.remove = snd_acp6x_remove,
+	.driver = {
+		.pm = &acp6x_pm,
+	}
+};
+
+module_pci_driver(yc_acp6x_driver);
+
+MODULE_AUTHOR("Vijendar.Mukunda@amd.com");
+MODULE_DESCRIPTION("AMD ACP Yellow Carp PCI driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/atmel-classd.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/atmel-classd.c
@@ -458,7 +458,6 @@
 	.num_controls		= ARRAY_SIZE(atmel_classd_snd_controls),
 	.idle_bias_on		= 1,
 	.use_pmdown_time	= 1,
-	.endianness		= 1,
 };
 
 /* ASoC sound card */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/atmel-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/atmel-i2s.c
@@ -163,11 +163,14 @@
 
 #define I2S_MCK_12M288		12288000UL
 #define I2S_MCK_11M2896		11289600UL
+#define I2S_MCK_6M144		6144000UL
 
 /* mck = (32 * (imckfs+1) / (imckdiv+1)) * fs */
 static const struct atmel_i2s_gck_param gck_params[] = {
+	/* mck = 6.144Mhz */
+	{  8000, I2S_MCK_6M144,  1, 47},	/* mck =  768 fs */
+
 	/* mck = 12.288MHz */
-	{  8000, I2S_MCK_12M288, 0, 47},	/* mck = 1536 fs */
 	{ 16000, I2S_MCK_12M288, 1, 47},	/* mck =  768 fs */
 	{ 24000, I2S_MCK_12M288, 3, 63},	/* mck =  512 fs */
 	{ 32000, I2S_MCK_12M288, 3, 47},	/* mck =  384 fs */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/atmel-pdmic.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/atmel-pdmic.c
@@ -481,7 +481,6 @@
 	.num_controls		= ARRAY_SIZE(atmel_pdmic_snd_controls),
 	.idle_bias_on		= 1,
 	.use_pmdown_time	= 1,
-	.endianness		= 1,
 };
 
 /* ASoC sound card */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/atmel_ssc_dai.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/atmel_ssc_dai.c
@@ -280,7 +280,10 @@
 
 	/* Enable PMC peripheral clock for this SSC */
 	pr_debug("atmel_ssc_dai: Starting clock\n");
-	clk_enable(ssc_p->ssc->clk);
+	ret = clk_enable(ssc_p->ssc->clk);
+	if (ret)
+		return ret;
+
 	ssc_p->mck_rate = clk_get_rate(ssc_p->ssc->clk);
 
 	/* Reset the SSC unless initialized to keep it in a clean state */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/mchp-spdifrx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/mchp-spdifrx.c
@@ -217,7 +217,6 @@
 struct mchp_spdifrx_user_data {
 	unsigned char data[SPDIFRX_UD_BITS / 8];
 	struct completion done;
-	spinlock_t lock;	/* protect access to user data */
 };
 
 struct mchp_spdifrx_mixer_control {
@@ -231,13 +230,13 @@
 struct mchp_spdifrx_dev {
 	struct snd_dmaengine_dai_dma_data	capture;
 	struct mchp_spdifrx_mixer_control	control;
-	spinlock_t				blockend_lock;	/* protect access to blockend_refcount */
-	int					blockend_refcount;
+	struct mutex				mlock;
 	struct device				*dev;
 	struct regmap				*regmap;
 	struct clk				*pclk;
 	struct clk				*gclk;
 	unsigned int				fmt;
+	unsigned int				trigger_enabled;
 	unsigned int				gclk_enabled:1;
 };
 
@@ -275,35 +274,11 @@
 	}
 }
 
-/* called from non-atomic context only */
-static void mchp_spdifrx_isr_blockend_en(struct mchp_spdifrx_dev *dev)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&dev->blockend_lock, flags);
-	dev->blockend_refcount++;
-	/* don't enable BLOCKEND interrupt if it's already enabled */
-	if (dev->blockend_refcount == 1)
-		regmap_write(dev->regmap, SPDIFRX_IER, SPDIFRX_IR_BLOCKEND);
-	spin_unlock_irqrestore(&dev->blockend_lock, flags);
-}
-
-/* called from atomic context only */
-static void mchp_spdifrx_isr_blockend_dis(struct mchp_spdifrx_dev *dev)
-{
-	spin_lock(&dev->blockend_lock);
-	dev->blockend_refcount--;
-	/* don't enable BLOCKEND interrupt if it's already enabled */
-	if (dev->blockend_refcount == 0)
-		regmap_write(dev->regmap, SPDIFRX_IDR, SPDIFRX_IR_BLOCKEND);
-	spin_unlock(&dev->blockend_lock);
-}
-
 static irqreturn_t mchp_spdif_interrupt(int irq, void *dev_id)
 {
 	struct mchp_spdifrx_dev *dev = dev_id;
 	struct mchp_spdifrx_mixer_control *ctrl = &dev->control;
-	u32 sr, imr, pending, idr = 0;
+	u32 sr, imr, pending;
 	irqreturn_t ret = IRQ_NONE;
 	int ch;
 
@@ -318,13 +293,10 @@
 
 	if (pending & SPDIFRX_IR_BLOCKEND) {
 		for (ch = 0; ch < SPDIFRX_CHANNELS; ch++) {
-			spin_lock(&ctrl->user_data[ch].lock);
 			mchp_spdifrx_channel_user_data_read(dev, ch);
-			spin_unlock(&ctrl->user_data[ch].lock);
-
 			complete(&ctrl->user_data[ch].done);
 		}
-		mchp_spdifrx_isr_blockend_dis(dev);
+		regmap_write(dev->regmap, SPDIFRX_IDR, SPDIFRX_IR_BLOCKEND);
 		ret = IRQ_HANDLED;
 	}
 
@@ -332,7 +304,7 @@
 		if (pending & SPDIFRX_IR_CSC(ch)) {
 			mchp_spdifrx_channel_status_read(dev, ch);
 			complete(&ctrl->ch_stat[ch].done);
-			idr |= SPDIFRX_IR_CSC(ch);
+			regmap_write(dev->regmap, SPDIFRX_IDR, SPDIFRX_IR_CSC(ch));
 			ret = IRQ_HANDLED;
 		}
 	}
@@ -342,8 +314,6 @@
 		ret = IRQ_HANDLED;
 	}
 
-	regmap_write(dev->regmap, SPDIFRX_IDR, idr);
-
 	return ret;
 }
 
@@ -351,47 +321,40 @@
 				struct snd_soc_dai *dai)
 {
 	struct mchp_spdifrx_dev *dev = snd_soc_dai_get_drvdata(dai);
-	u32 mr;
-	int running;
-	int ret;
-
-	regmap_read(dev->regmap, SPDIFRX_MR, &mr);
-	running = !!(mr & SPDIFRX_MR_RXEN_ENABLE);
+	int ret = 0;
 
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_START:
 	case SNDRV_PCM_TRIGGER_RESUME:
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
-		if (!running) {
-			mr &= ~SPDIFRX_MR_RXEN_MASK;
-			mr |= SPDIFRX_MR_RXEN_ENABLE;
-			/* enable overrun interrupts */
-			regmap_write(dev->regmap, SPDIFRX_IER,
-				     SPDIFRX_IR_OVERRUN);
-		}
+		mutex_lock(&dev->mlock);
+		/* Enable overrun interrupts */
+		regmap_write(dev->regmap, SPDIFRX_IER, SPDIFRX_IR_OVERRUN);
+
+		/* Enable receiver. */
+		regmap_update_bits(dev->regmap, SPDIFRX_MR, SPDIFRX_MR_RXEN_MASK,
+				   SPDIFRX_MR_RXEN_ENABLE);
+		dev->trigger_enabled = true;
+		mutex_unlock(&dev->mlock);
 		break;
 	case SNDRV_PCM_TRIGGER_STOP:
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
-		if (running) {
-			mr &= ~SPDIFRX_MR_RXEN_MASK;
-			mr |= SPDIFRX_MR_RXEN_DISABLE;
-			/* disable overrun interrupts */
-			regmap_write(dev->regmap, SPDIFRX_IDR,
-				     SPDIFRX_IR_OVERRUN);
-		}
+		mutex_lock(&dev->mlock);
+		/* Disable overrun interrupts */
+		regmap_write(dev->regmap, SPDIFRX_IDR, SPDIFRX_IR_OVERRUN);
+
+		/* Disable receiver. */
+		regmap_update_bits(dev->regmap, SPDIFRX_MR, SPDIFRX_MR_RXEN_MASK,
+				   SPDIFRX_MR_RXEN_DISABLE);
+		dev->trigger_enabled = false;
+		mutex_unlock(&dev->mlock);
 		break;
 	default:
-		return -EINVAL;
+		ret = -EINVAL;
 	}
 
-	ret = regmap_write(dev->regmap, SPDIFRX_MR, mr);
-	if (ret) {
-		dev_err(dev->dev, "unable to enable/disable RX: %d\n", ret);
-		return ret;
-	}
-
-	return 0;
+	return ret;
 }
 
 static int mchp_spdifrx_hw_params(struct snd_pcm_substream *substream,
@@ -399,7 +362,7 @@
 				  struct snd_soc_dai *dai)
 {
 	struct mchp_spdifrx_dev *dev = snd_soc_dai_get_drvdata(dai);
-	u32 mr;
+	u32 mr = 0;
 	int ret;
 
 	dev_dbg(dev->dev, "%s() rate=%u format=%#x width=%u channels=%u\n",
@@ -411,13 +374,6 @@
 		return -EINVAL;
 	}
 
-	regmap_read(dev->regmap, SPDIFRX_MR, &mr);
-
-	if (mr & SPDIFRX_MR_RXEN_ENABLE) {
-		dev_err(dev->dev, "PCM already running\n");
-		return -EBUSY;
-	}
-
 	if (params_channels(params) != SPDIFRX_CHANNELS) {
 		dev_err(dev->dev, "unsupported number of channels: %d\n",
 			params_channels(params));
@@ -443,6 +399,13 @@
 		return -EINVAL;
 	}
 
+	mutex_lock(&dev->mlock);
+	if (dev->trigger_enabled) {
+		dev_err(dev->dev, "PCM already running\n");
+		ret = -EBUSY;
+		goto unlock;
+	}
+
 	if (dev->gclk_enabled) {
 		clk_disable_unprepare(dev->gclk);
 		dev->gclk_enabled = 0;
@@ -453,19 +416,24 @@
 		dev_err(dev->dev,
 			"unable to set gclk min rate: rate %u * ratio %u + 1\n",
 			params_rate(params), SPDIFRX_GCLK_RATIO_MIN);
-		return ret;
+		goto unlock;
 	}
 	ret = clk_prepare_enable(dev->gclk);
 	if (ret) {
 		dev_err(dev->dev, "unable to enable gclk: %d\n", ret);
-		return ret;
+		goto unlock;
 	}
 	dev->gclk_enabled = 1;
 
 	dev_dbg(dev->dev, "GCLK range min set to %d\n",
 		params_rate(params) * SPDIFRX_GCLK_RATIO_MIN + 1);
 
-	return regmap_write(dev->regmap, SPDIFRX_MR, mr);
+	ret = regmap_write(dev->regmap, SPDIFRX_MR, mr);
+
+unlock:
+	mutex_unlock(&dev->mlock);
+
+	return ret;
 }
 
 static int mchp_spdifrx_hw_free(struct snd_pcm_substream *substream,
@@ -473,10 +441,12 @@
 {
 	struct mchp_spdifrx_dev *dev = snd_soc_dai_get_drvdata(dai);
 
+	mutex_lock(&dev->mlock);
 	if (dev->gclk_enabled) {
 		clk_disable_unprepare(dev->gclk);
 		dev->gclk_enabled = 0;
 	}
+	mutex_unlock(&dev->mlock);
 	return 0;
 }
 
@@ -513,22 +483,51 @@
 {
 	struct mchp_spdifrx_mixer_control *ctrl = &dev->control;
 	struct mchp_spdifrx_ch_stat *ch_stat = &ctrl->ch_stat[channel];
-	int ret;
+	int ret = 0;
+
+	mutex_lock(&dev->mlock);
 
-	regmap_write(dev->regmap, SPDIFRX_IER, SPDIFRX_IR_CSC(channel));
-	/* check for new data available */
-	ret = wait_for_completion_interruptible_timeout(&ch_stat->done,
-							msecs_to_jiffies(100));
-	/* IP might not be started or valid stream might not be present */
-	if (ret < 0) {
-		dev_dbg(dev->dev, "channel status for channel %d timeout\n",
-			channel);
+	/*
+	 * We may reach this point with both clocks enabled but the receiver
+	 * still disabled. To void waiting for completion and return with
+	 * timeout check the dev->trigger_enabled.
+	 *
+	 * To retrieve data:
+	 * - if the receiver is enabled CSC IRQ will update the data in software
+	 *   caches (ch_stat->data)
+	 * - otherwise we just update it here the software caches with latest
+	 *   available information and return it; in this case we don't need
+	 *   spin locking as the IRQ is disabled and will not be raised from
+	 *   anywhere else.
+	 */
+
+	if (dev->trigger_enabled) {
+		reinit_completion(&ch_stat->done);
+		regmap_write(dev->regmap, SPDIFRX_IER, SPDIFRX_IR_CSC(channel));
+		/* Check for new data available */
+		ret = wait_for_completion_interruptible_timeout(&ch_stat->done,
+								msecs_to_jiffies(100));
+		/* Valid stream might not be present */
+		if (ret <= 0) {
+			dev_dbg(dev->dev, "channel status for channel %d timeout\n",
+				channel);
+			regmap_write(dev->regmap, SPDIFRX_IDR, SPDIFRX_IR_CSC(channel));
+			ret = ret ? : -ETIMEDOUT;
+			goto unlock;
+		} else {
+			ret = 0;
+		}
+	} else {
+		/* Update software cache with latest channel status. */
+		mchp_spdifrx_channel_status_read(dev, channel);
 	}
 
 	memcpy(uvalue->value.iec958.status, ch_stat->data,
 	       sizeof(ch_stat->data));
 
-	return 0;
+unlock:
+	mutex_unlock(&dev->mlock);
+	return ret;
 }
 
 static int mchp_spdifrx_cs1_get(struct snd_kcontrol *kcontrol,
@@ -562,28 +561,49 @@
 				       int channel,
 				       struct snd_ctl_elem_value *uvalue)
 {
-	unsigned long flags;
 	struct mchp_spdifrx_mixer_control *ctrl = &dev->control;
 	struct mchp_spdifrx_user_data *user_data = &ctrl->user_data[channel];
-	int ret;
+	int ret = 0;
+
+	mutex_lock(&dev->mlock);
 
-	reinit_completion(&user_data->done);
-	mchp_spdifrx_isr_blockend_en(dev);
-	ret = wait_for_completion_interruptible_timeout(&user_data->done,
-							msecs_to_jiffies(100));
-	/* IP might not be started or valid stream might not be present */
-	if (ret <= 0) {
-		dev_dbg(dev->dev, "user data for channel %d timeout\n",
-			channel);
-		return ret;
+	/*
+	 * We may reach this point with both clocks enabled but the receiver
+	 * still disabled. To void waiting for completion to just timeout we
+	 * check here the dev->trigger_enabled flag.
+	 *
+	 * To retrieve data:
+	 * - if the receiver is enabled we need to wait for blockend IRQ to read
+	 *   data to and update it for us in software caches
+	 * - otherwise reading the SPDIFRX_CHUD() registers is enough.
+	 */
+
+	if (dev->trigger_enabled) {
+		reinit_completion(&user_data->done);
+		regmap_write(dev->regmap, SPDIFRX_IER, SPDIFRX_IR_BLOCKEND);
+		ret = wait_for_completion_interruptible_timeout(&user_data->done,
+								msecs_to_jiffies(100));
+		/* Valid stream might not be present. */
+		if (ret <= 0) {
+			dev_dbg(dev->dev, "user data for channel %d timeout\n",
+				channel);
+			regmap_write(dev->regmap, SPDIFRX_IDR, SPDIFRX_IR_BLOCKEND);
+			ret = ret ? : -ETIMEDOUT;
+			goto unlock;
+		} else {
+			ret = 0;
+		}
+	} else {
+		/* Update software cache with last available data. */
+		mchp_spdifrx_channel_user_data_read(dev, channel);
 	}
 
-	spin_lock_irqsave(&user_data->lock, flags);
 	memcpy(uvalue->value.iec958.subcode, user_data->data,
 	       sizeof(user_data->data));
-	spin_unlock_irqrestore(&user_data->lock, flags);
 
-	return 0;
+unlock:
+	mutex_unlock(&dev->mlock);
+	return ret;
 }
 
 static int mchp_spdifrx_subcode_ch1_get(struct snd_kcontrol *kcontrol,
@@ -624,10 +644,24 @@
 	u32 val;
 	bool ulock_old = ctrl->ulock;
 
-	regmap_read(dev->regmap, SPDIFRX_RSR, &val);
-	ctrl->ulock = !(val & SPDIFRX_RSR_ULOCK);
+	mutex_lock(&dev->mlock);
+
+	/*
+	 * The RSR.ULOCK has wrong value if both pclk and gclk are enabled
+	 * and the receiver is disabled. Thus we take into account the
+	 * dev->trigger_enabled here to return a real status.
+	 */
+	if (dev->trigger_enabled) {
+		regmap_read(dev->regmap, SPDIFRX_RSR, &val);
+		ctrl->ulock = !(val & SPDIFRX_RSR_ULOCK);
+	} else {
+		ctrl->ulock = 0;
+	}
+
 	uvalue->value.integer.value[0] = ctrl->ulock;
 
+	mutex_unlock(&dev->mlock);
+
 	return ulock_old != ctrl->ulock;
 }
 
@@ -640,8 +674,22 @@
 	u32 val;
 	bool badf_old = ctrl->badf;
 
-	regmap_read(dev->regmap, SPDIFRX_RSR, &val);
-	ctrl->badf = !!(val & SPDIFRX_RSR_BADF);
+	mutex_lock(&dev->mlock);
+
+	/*
+	 * The RSR.ULOCK has wrong value if both pclk and gclk are enabled
+	 * and the receiver is disabled. Thus we take into account the
+	 * dev->trigger_enabled here to return a real status.
+	 */
+	if (dev->trigger_enabled) {
+		regmap_read(dev->regmap, SPDIFRX_RSR, &val);
+		ctrl->badf = !!(val & SPDIFRX_RSR_BADF);
+	} else {
+		ctrl->badf = 0;
+	}
+
+	mutex_unlock(&dev->mlock);
+
 	uvalue->value.integer.value[0] = ctrl->badf;
 
 	return badf_old != ctrl->badf;
@@ -653,11 +701,48 @@
 	struct snd_soc_dai *dai = snd_kcontrol_chip(kcontrol);
 	struct mchp_spdifrx_dev *dev = snd_soc_dai_get_drvdata(dai);
 	struct mchp_spdifrx_mixer_control *ctrl = &dev->control;
-	u32 val;
+	u32 val = ~0U, loops = 10;
+	int ret;
 	bool signal_old = ctrl->signal;
 
-	regmap_read(dev->regmap, SPDIFRX_RSR, &val);
-	ctrl->signal = !(val & SPDIFRX_RSR_NOSIGNAL);
+	mutex_lock(&dev->mlock);
+
+	/*
+	 * To get the signal we need to have receiver enabled. This
+	 * could be enabled also from trigger() function thus we need to
+	 * take care of not disabling the receiver when it runs.
+	 */
+	if (!dev->trigger_enabled) {
+		ret = clk_prepare_enable(dev->gclk);
+		if (ret)
+			goto unlock;
+
+		regmap_update_bits(dev->regmap, SPDIFRX_MR, SPDIFRX_MR_RXEN_MASK,
+				   SPDIFRX_MR_RXEN_ENABLE);
+
+		/* Wait for RSR.ULOCK bit. */
+		while (--loops) {
+			regmap_read(dev->regmap, SPDIFRX_RSR, &val);
+			if (!(val & SPDIFRX_RSR_ULOCK))
+				break;
+			usleep_range(100, 150);
+		}
+
+		regmap_update_bits(dev->regmap, SPDIFRX_MR, SPDIFRX_MR_RXEN_MASK,
+				   SPDIFRX_MR_RXEN_DISABLE);
+
+		clk_disable_unprepare(dev->gclk);
+	} else {
+		regmap_read(dev->regmap, SPDIFRX_RSR, &val);
+	}
+
+unlock:
+	mutex_unlock(&dev->mlock);
+
+	if (!(val & SPDIFRX_RSR_ULOCK))
+		ctrl->signal = !(val & SPDIFRX_RSR_NOSIGNAL);
+	else
+		ctrl->signal = 0;
 	uvalue->value.integer.value[0] = ctrl->signal;
 
 	return signal_old != ctrl->signal;
@@ -682,18 +767,32 @@
 	u32 val;
 	int rate;
 
-	regmap_read(dev->regmap, SPDIFRX_RSR, &val);
+	mutex_lock(&dev->mlock);
 
-	/* if the receiver is not locked, ISF data is invalid */
-	if (val & SPDIFRX_RSR_ULOCK || !(val & SPDIFRX_RSR_IFS_MASK)) {
+	/*
+	 * The RSR.ULOCK has wrong value if both pclk and gclk are enabled
+	 * and the receiver is disabled. Thus we take into account the
+	 * dev->trigger_enabled here to return a real status.
+	 */
+	if (dev->trigger_enabled) {
+		regmap_read(dev->regmap, SPDIFRX_RSR, &val);
+		/* If the receiver is not locked, ISF data is invalid. */
+		if (val & SPDIFRX_RSR_ULOCK || !(val & SPDIFRX_RSR_IFS_MASK)) {
+			ucontrol->value.integer.value[0] = 0;
+			goto unlock;
+		}
+	} else {
+		/* Reveicer is not locked, IFS data is invalid. */
 		ucontrol->value.integer.value[0] = 0;
-		return 0;
+		goto unlock;
 	}
 
 	rate = clk_get_rate(dev->gclk);
 
 	ucontrol->value.integer.value[0] = rate / (32 * SPDIFRX_RSR_IFS(val));
 
+unlock:
+	mutex_unlock(&dev->mlock);
 	return 0;
 }
 
@@ -805,11 +904,9 @@
 		     SPDIFRX_MR_AUTORST_NOACTION |
 		     SPDIFRX_MR_PACK_DISABLED);
 
-	dev->blockend_refcount = 0;
 	for (ch = 0; ch < SPDIFRX_CHANNELS; ch++) {
 		init_completion(&ctrl->ch_stat[ch].done);
 		init_completion(&ctrl->user_data[ch].done);
-		spin_lock_init(&ctrl->user_data[ch].lock);
 	}
 
 	/* Add controls */
@@ -824,7 +921,7 @@
 	struct mchp_spdifrx_dev *dev = snd_soc_dai_get_drvdata(dai);
 
 	/* Disable interrupts */
-	regmap_write(dev->regmap, SPDIFRX_IDR, 0xFF);
+	regmap_write(dev->regmap, SPDIFRX_IDR, GENMASK(14, 0));
 
 	clk_disable_unprepare(dev->pclk);
 
@@ -909,7 +1006,17 @@
 			"failed to get the PMC generated clock: %d\n", err);
 		return err;
 	}
-	spin_lock_init(&dev->blockend_lock);
+
+	/*
+	 * Signal control need a valid rate on gclk. hw_params() configures
+	 * it propertly but requesting signal before any hw_params() has been
+	 * called lead to invalid value returned for signal. Thus, configure
+	 * gclk at a valid rate, here, in initialization, to simplify the
+	 * control path.
+	 */
+	clk_set_min_rate(dev->gclk, 48000 * SPDIFRX_GCLK_RATIO_MIN + 1);
+
+	mutex_init(&dev->mlock);
 
 	dev->dev = &pdev->dev;
 	dev->regmap = regmap;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/mchp-spdiftx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/mchp-spdiftx.c
@@ -196,8 +196,7 @@
 	struct clk				*pclk;
 	struct clk				*gclk;
 	unsigned int				fmt;
-	const struct mchp_i2s_caps		*caps;
-	int					gclk_enabled:1;
+	unsigned int				gclk_enabled:1;
 };
 
 static inline int mchp_spdiftx_is_running(struct mchp_spdiftx_dev *dev)
@@ -766,8 +765,6 @@
 MODULE_DEVICE_TABLE(of, mchp_spdiftx_dt_ids);
 static int mchp_spdiftx_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
-	const struct of_device_id *match;
 	struct mchp_spdiftx_dev *dev;
 	struct resource *mem;
 	struct regmap *regmap;
@@ -781,11 +778,6 @@
 	if (!dev)
 		return -ENOMEM;
 
-	/* Get hardware capabilities. */
-	match = of_match_node(mchp_spdiftx_dt_ids, np);
-	if (match)
-		dev->caps = match->data;
-
 	/* Map I/O registers. */
 	base = devm_platform_get_and_ioremap_resource(pdev, 0, &mem);
 	if (IS_ERR(base))
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/mikroe-proto.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/mikroe-proto.c
@@ -115,7 +115,8 @@
 	cpu_np = of_parse_phandle(np, "i2s-controller", 0);
 	if (!cpu_np) {
 		dev_err(&pdev->dev, "i2s-controller missing\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_codec_node;
 	}
 	dai->cpus->of_node = cpu_np;
 	dai->platforms->of_node = cpu_np;
@@ -125,7 +126,8 @@
 						       &bitclkmaster, &framemaster);
 	if (bitclkmaster != framemaster) {
 		dev_err(&pdev->dev, "Must be the same bitclock and frame master\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_cpu_node;
 	}
 	if (bitclkmaster) {
 		if (codec_np == bitclkmaster)
@@ -136,18 +138,20 @@
 		dai_fmt |= snd_soc_daifmt_parse_clock_provider_as_flag(np, NULL);
 	}
 
-	of_node_put(bitclkmaster);
-	of_node_put(framemaster);
-	dai->dai_fmt = dai_fmt;
-
-	of_node_put(codec_np);
-	of_node_put(cpu_np);
 
+	dai->dai_fmt = dai_fmt;
 	ret = snd_soc_register_card(&snd_proto);
 	if (ret && ret != -EPROBE_DEFER)
 		dev_err(&pdev->dev,
 			"snd_soc_register_card() failed: %d\n", ret);
 
+
+put_cpu_node:
+	of_node_put(bitclkmaster);
+	of_node_put(framemaster);
+	of_node_put(cpu_np);
+put_codec_node:
+	of_node_put(codec_np);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/sam9g20_wm8731.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/sam9g20_wm8731.c
@@ -214,6 +214,7 @@
 	cpu_np = of_parse_phandle(np, "atmel,ssc-controller", 0);
 	if (!cpu_np) {
 		dev_err(&pdev->dev, "dai and pcm info missing\n");
+		of_node_put(codec_np);
 		return -EINVAL;
 	}
 	at91sam9g20ek_dai.cpus->of_node = cpu_np;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/atmel/sam9x5_wm8731.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/atmel/sam9x5_wm8731.c
@@ -142,7 +142,7 @@
 	if (!cpu_np) {
 		dev_err(&pdev->dev, "atmel,ssc-controller node missing\n");
 		ret = -EINVAL;
-		goto out;
+		goto out_put_codec_np;
 	}
 	dai->cpus->of_node = cpu_np;
 	dai->platforms->of_node = cpu_np;
@@ -153,12 +153,9 @@
 	if (ret != 0) {
 		dev_err(&pdev->dev, "Failed to set SSC %d for audio: %d\n",
 			ret, priv->ssc_id);
-		goto out;
+		goto out_put_cpu_np;
 	}
 
-	of_node_put(codec_np);
-	of_node_put(cpu_np);
-
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
 	if (ret) {
 		dev_err(&pdev->dev, "Platform device allocation failed\n");
@@ -167,10 +164,14 @@
 
 	dev_dbg(&pdev->dev, "%s ok\n", __func__);
 
-	return ret;
+	goto out_put_cpu_np;
 
 out_put_audio:
 	atmel_ssc_put_audio(priv->ssc_id);
+out_put_cpu_np:
+	of_node_put(cpu_np);
+out_put_codec_np:
+	of_node_put(codec_np);
 out:
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/au1x/db1200.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/au1x/db1200.c
@@ -44,6 +44,7 @@
 	},
 	{},
 };
+MODULE_DEVICE_TABLE(platform, db1200_pids);
 
 /*-------------------------  AC97 PART  ---------------------------*/
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/Kconfig
@@ -61,6 +61,8 @@
 	imply SND_SOC_CS35L34
 	imply SND_SOC_CS35L35
 	imply SND_SOC_CS35L36
+	imply SND_SOC_CS35L41_SPI
+	imply SND_SOC_CS35L41_I2C
 	imply SND_SOC_CS42L42
 	imply SND_SOC_CS42L51_I2C
 	imply SND_SOC_CS42L52
@@ -235,8 +237,7 @@
 	imply SND_SOC_UDA1380
 	imply SND_SOC_WCD9335
 	imply SND_SOC_WCD934X
-	imply SND_SOC_WCD937X
-	imply SND_SOC_WCD938X
+	imply SND_SOC_WCD938X_SDW
 	imply SND_SOC_LPASS_RX_MACRO
 	imply SND_SOC_LPASS_TX_MACRO
 	imply SND_SOC_WL1273
@@ -336,11 +337,15 @@
 	default y if SND_SOC_WM5102=y
 	default y if SND_SOC_WM5110=y
 	default y if SND_SOC_WM2200=y
+	default y if SND_SOC_CS35L41_SPI=y
+	default y if SND_SOC_CS35L41_I2C=y
 	default m if SND_SOC_MADERA=m
 	default m if SND_SOC_CS47L24=m
 	default m if SND_SOC_WM5102=m
 	default m if SND_SOC_WM5110=m
 	default m if SND_SOC_WM2200=m
+	default m if SND_SOC_CS35L41_SPI=m
+	default m if SND_SOC_CS35L41_I2C=m
 
 config SND_SOC_AB8500_CODEC
 	tristate
@@ -602,6 +607,26 @@
 	tristate "Cirrus Logic CS35L36 CODEC"
 	depends on I2C
 
+config SND_SOC_CS35L41_LIB
+	tristate
+
+config SND_SOC_CS35L41
+	tristate
+
+config SND_SOC_CS35L41_SPI
+	tristate "Cirrus Logic CS35L41 CODEC (SPI)"
+	depends on SPI_MASTER
+	select SND_SOC_CS35L41_LIB
+	select SND_SOC_CS35L41
+	select REGMAP_SPI
+
+config SND_SOC_CS35L41_I2C
+	tristate "Cirrus Logic CS35L41 CODEC (I2C)"
+	depends on I2C
+	select SND_SOC_CS35L41_LIB
+	select SND_SOC_CS35L41
+	select REGMAP_I2C
+
 config SND_SOC_CS42L42
 	tristate "Cirrus Logic CS42L42 CODEC"
 	depends on I2C
@@ -691,6 +716,7 @@
 
 config SND_SOC_CS47L15
 	tristate
+	depends on MFD_CS47L15
 
 config SND_SOC_CS47L24
 	tristate
@@ -698,15 +724,19 @@
 
 config SND_SOC_CS47L35
 	tristate
+	depends on MFD_CS47L35
 
 config SND_SOC_CS47L85
 	tristate
+	depends on MFD_CS47L85
 
 config SND_SOC_CS47L90
 	tristate
+	depends on MFD_CS47L90
 
 config SND_SOC_CS47L92
 	tristate
+	depends on MFD_CS47L92
 
 # Cirrus Logic Quad-Channel ADC
 config SND_SOC_CS53L30
@@ -896,7 +926,6 @@
 
 config SND_SOC_MAX98357A
 	tristate "Maxim MAX98357A CODEC"
-	depends on GPIOLIB
 
 config SND_SOC_MAX98371
 	tristate
@@ -1145,7 +1174,6 @@
 
 config SND_SOC_RT1015P
 	tristate
-	depends on GPIOLIB
 
 config SND_SOC_RT1019
 	tristate
@@ -1381,6 +1409,7 @@
 config SND_SOC_STAC9766
 	tristate
 	depends on SND_SOC_AC97_BUS
+	select REGMAP_AC97
 
 config SND_SOC_STI_SAS
 	tristate "codec Audio support for STI SAS codec"
@@ -1773,6 +1802,7 @@
 
 config SND_SOC_WM8994
 	tristate
+	depends on MFD_WM8994
 
 config SND_SOC_WM8995
 	tristate
@@ -1828,7 +1858,7 @@
 config SND_SOC_ZL38060
 	tristate "Microsemi ZL38060 Connected Home Audio Processor"
 	depends on SPI_MASTER
-	select GPIOLIB
+	depends on GPIOLIB
 	select REGMAP
 	help
 	  Support for ZL38060 Connected Home Audio Processor from Microsemi,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/Makefile
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/Makefile
@@ -54,6 +54,10 @@
 snd-soc-cs35l34-objs := cs35l34.o
 snd-soc-cs35l35-objs := cs35l35.o
 snd-soc-cs35l36-objs := cs35l36.o
+snd-soc-cs35l41-lib-objs := cs35l41-lib.o
+snd-soc-cs35l41-objs := cs35l41.o
+snd-soc-cs35l41-spi-objs := cs35l41-spi.o
+snd-soc-cs35l41-i2c-objs := cs35l41-i2c.o
 snd-soc-cs42l42-objs := cs42l42.o
 snd-soc-cs42l51-objs := cs42l51.o
 snd-soc-cs42l51-i2c-objs := cs42l51-i2c.o
@@ -385,6 +389,10 @@
 obj-$(CONFIG_SND_SOC_CS35L34)	+= snd-soc-cs35l34.o
 obj-$(CONFIG_SND_SOC_CS35L35)	+= snd-soc-cs35l35.o
 obj-$(CONFIG_SND_SOC_CS35L36)	+= snd-soc-cs35l36.o
+obj-$(CONFIG_SND_SOC_CS35L41)	+= snd-soc-cs35l41.o
+obj-$(CONFIG_SND_SOC_CS35L41_LIB)	+= snd-soc-cs35l41-lib.o
+obj-$(CONFIG_SND_SOC_CS35L41_SPI)	+= snd-soc-cs35l41-spi.o
+obj-$(CONFIG_SND_SOC_CS35L41_I2C)	+= snd-soc-cs35l41-i2c.o
 obj-$(CONFIG_SND_SOC_CS42L42)	+= snd-soc-cs42l42.o
 obj-$(CONFIG_SND_SOC_CS42L51)	+= snd-soc-cs42l51.o
 obj-$(CONFIG_SND_SOC_CS42L51_I2C)	+= snd-soc-cs42l51-i2c.o
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/adau7118.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/adau7118.c
@@ -445,22 +445,6 @@
 	.non_legacy_dai_naming	= 1,
 };
 
-static void adau7118_regulator_disable(void *data)
-{
-	struct adau7118_data *st = data;
-	int ret;
-	/*
-	 * If we fail to disable DVDD, don't bother in trying IOVDD. We
-	 * actually don't want to be left in the situation where DVDD
-	 * is enabled and IOVDD is disabled.
-	 */
-	ret = regulator_disable(st->dvdd);
-	if (ret)
-		return;
-
-	regulator_disable(st->iovdd);
-}
-
 static int adau7118_regulator_setup(struct adau7118_data *st)
 {
 	st->iovdd = devm_regulator_get(st->dev, "iovdd");
@@ -482,8 +466,7 @@
 		regcache_cache_only(st->map, true);
 	}
 
-	return devm_add_action_or_reset(st->dev, adau7118_regulator_disable,
-					st);
+	return 0;
 }
 
 static int adau7118_parset_dt(const struct adau7118_data *st)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/arizona.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/arizona.c
@@ -967,7 +967,7 @@
 		case ARIZONA_OUT3L_ENA_SHIFT:
 		case ARIZONA_OUT3R_ENA_SHIFT:
 			priv->out_up_pending++;
-			priv->out_up_delay += 17;
+			priv->out_up_delay += 17000;
 			break;
 		case ARIZONA_OUT4L_ENA_SHIFT:
 		case ARIZONA_OUT4R_ENA_SHIFT:
@@ -977,7 +977,7 @@
 			case WM8997:
 				break;
 			default:
-				priv->out_up_delay += 10;
+				priv->out_up_delay += 10000;
 				break;
 			}
 			break;
@@ -999,7 +999,7 @@
 			if (!priv->out_up_pending && priv->out_up_delay) {
 				dev_dbg(component->dev, "Power up delay: %d\n",
 					priv->out_up_delay);
-				msleep(priv->out_up_delay);
+				fsleep(priv->out_up_delay);
 				priv->out_up_delay = 0;
 			}
 			break;
@@ -1017,7 +1017,7 @@
 		case ARIZONA_OUT3L_ENA_SHIFT:
 		case ARIZONA_OUT3R_ENA_SHIFT:
 			priv->out_down_pending++;
-			priv->out_down_delay++;
+			priv->out_down_delay += 1000;
 			break;
 		case ARIZONA_OUT4L_ENA_SHIFT:
 		case ARIZONA_OUT4R_ENA_SHIFT:
@@ -1028,10 +1028,10 @@
 				break;
 			case WM8998:
 			case WM1814:
-				priv->out_down_delay += 5;
+				priv->out_down_delay += 5000;
 				break;
 			default:
-				priv->out_down_delay++;
+				priv->out_down_delay += 1000;
 				break;
 			}
 			break;
@@ -1053,7 +1053,7 @@
 			if (!priv->out_down_pending && priv->out_down_delay) {
 				dev_dbg(component->dev, "Power down delay: %d\n",
 					priv->out_down_delay);
-				msleep(priv->out_down_delay);
+				fsleep(priv->out_down_delay);
 				priv->out_down_delay = 0;
 			}
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cpcap.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cpcap.c
@@ -1667,6 +1667,8 @@
 {
 	struct device_node *codec_node =
 		of_get_child_by_name(pdev->dev.parent->of_node, "audio-codec");
+	if (!codec_node)
+		return -ENODEV;
 
 	pdev->dev.of_node = codec_node;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cros_ec_codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cros_ec_codec.c
@@ -994,6 +994,7 @@
 			dev_dbg(dev, "ap_shm_phys_addr=%#llx len=%#x\n",
 				priv->ap_shm_phys_addr, priv->ap_shm_len);
 		}
+		of_node_put(node);
 	}
 #endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l33.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l33.c
@@ -22,13 +22,11 @@
 #include <sound/soc-dapm.h>
 #include <sound/initval.h>
 #include <sound/tlv.h>
-#include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
 #include <sound/cs35l33.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
 #include <linux/regulator/machine.h>
-#include <linux/of_gpio.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
@@ -1169,7 +1167,7 @@
 
 	/* We could issue !RST or skip it based on AMP topology */
 	cs35l33->reset_gpio = devm_gpiod_get_optional(&i2c_client->dev,
-			"reset-gpios", GPIOD_OUT_HIGH);
+			"reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(cs35l33->reset_gpio)) {
 		dev_err(&i2c_client->dev, "%s ERROR: Can't get reset GPIO\n",
 			__func__);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l34.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l34.c
@@ -20,14 +20,12 @@
 #include <linux/regulator/machine.h>
 #include <linux/pm_runtime.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
 #include <linux/of_irq.h>
 #include <sound/core.h>
 #include <sound/pcm.h>
 #include <sound/pcm_params.h>
 #include <sound/soc.h>
 #include <sound/soc-dapm.h>
-#include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
 #include <sound/initval.h>
 #include <sound/tlv.h>
@@ -1063,7 +1061,7 @@
 		dev_err(&i2c_client->dev, "Failed to request IRQ: %d\n", ret);
 
 	cs35l34->reset_gpio = devm_gpiod_get_optional(&i2c_client->dev,
-				"reset-gpios", GPIOD_OUT_LOW);
+				"reset", GPIOD_OUT_LOW);
 	if (IS_ERR(cs35l34->reset_gpio)) {
 		ret = PTR_ERR(cs35l34->reset_gpio);
 		goto err_regulator;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l36.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l36.c
@@ -444,7 +444,8 @@
 	}
 }
 
-static DECLARE_TLV_DB_SCALE(dig_vol_tlv, -10200, 25, 0);
+static const DECLARE_TLV_DB_RANGE(dig_vol_tlv, 0, 912,
+				  TLV_DB_MINMAX_ITEM(-10200, 1200));
 static DECLARE_TLV_DB_SCALE(amp_gain_tlv, 0, 1, 1);
 
 static const char * const cs35l36_pcm_sftramp_text[] =  {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l41-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l41-i2c.c
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// cs35l41-i2c.c -- CS35l41 I2C driver
+//
+// Copyright 2017-2021 Cirrus Logic, Inc.
+//
+// Author: David Rhodes <david.rhodes@cirrus.com>
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include "cs35l41.h"
+
+static const struct i2c_device_id cs35l41_id_i2c[] = {
+	{ "cs35l40", 0 },
+	{ "cs35l41", 0 },
+	{ "cs35l51", 0 },
+	{ "cs35l53", 0 },
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, cs35l41_id_i2c);
+
+static int cs35l41_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	struct cs35l41_private *cs35l41;
+	struct device *dev = &client->dev;
+	struct cs35l41_platform_data *pdata = dev_get_platdata(dev);
+	const struct regmap_config *regmap_config = &cs35l41_regmap_i2c;
+	int ret;
+
+	cs35l41 = devm_kzalloc(dev, sizeof(struct cs35l41_private), GFP_KERNEL);
+
+	if (!cs35l41)
+		return -ENOMEM;
+
+	cs35l41->dev = dev;
+	cs35l41->irq = client->irq;
+
+	i2c_set_clientdata(client, cs35l41);
+	cs35l41->regmap = devm_regmap_init_i2c(client, regmap_config);
+	if (IS_ERR(cs35l41->regmap)) {
+		ret = PTR_ERR(cs35l41->regmap);
+		dev_err(cs35l41->dev, "Failed to allocate register map: %d\n", ret);
+		return ret;
+	}
+
+	return cs35l41_probe(cs35l41, pdata);
+}
+
+static int cs35l41_i2c_remove(struct i2c_client *client)
+{
+	struct cs35l41_private *cs35l41 = i2c_get_clientdata(client);
+
+	cs35l41_remove(cs35l41);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id cs35l41_of_match[] = {
+	{ .compatible = "cirrus,cs35l40" },
+	{ .compatible = "cirrus,cs35l41" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, cs35l41_of_match);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id cs35l41_acpi_match[] = {
+	{ "CSC3541", 0 }, /* Cirrus Logic PnP ID + part ID */
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, cs35l41_acpi_match);
+#endif
+
+static struct i2c_driver cs35l41_i2c_driver = {
+	.driver = {
+		.name		= "cs35l41",
+		.pm		= &cs35l41_pm_ops,
+		.of_match_table = of_match_ptr(cs35l41_of_match),
+		.acpi_match_table = ACPI_PTR(cs35l41_acpi_match),
+	},
+	.id_table	= cs35l41_id_i2c,
+	.probe		= cs35l41_i2c_probe,
+	.remove		= cs35l41_i2c_remove,
+};
+
+module_i2c_driver(cs35l41_i2c_driver);
+
+MODULE_DESCRIPTION("I2C CS35L41 driver");
+MODULE_AUTHOR("David Rhodes, Cirrus Logic Inc, <david.rhodes@cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l41-lib.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l41-lib.c
@@ -0,0 +1,1040 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// cs35l41-lib.c -- CS35L41 Common functions for HDA and ASoC Audio drivers
+//
+// Copyright 2017-2021 Cirrus Logic, Inc.
+//
+// Author: David Rhodes <david.rhodes@cirrus.com>
+// Author: Lucas Tanure <lucas.tanure@cirrus.com>
+
+#include <linux/dev_printk.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+#include <sound/cs35l41.h>
+
+static const struct reg_default cs35l41_reg[] = {
+	{ CS35L41_PWR_CTRL1,			0x00000000 },
+	{ CS35L41_PWR_CTRL2,			0x00000000 },
+	{ CS35L41_PWR_CTRL3,			0x01000010 },
+	{ CS35L41_GPIO_PAD_CONTROL,		0x00000000 },
+	{ CS35L41_GLOBAL_CLK_CTRL,		0x00000003 },
+	{ CS35L41_TST_FS_MON0,			0x00020016 },
+	{ CS35L41_BSTCVRT_COEFF,		0x00002424 },
+	{ CS35L41_BSTCVRT_SLOPE_LBST,		0x00007500 },
+	{ CS35L41_BSTCVRT_PEAK_CUR,		0x0000004A },
+	{ CS35L41_SP_ENABLES,			0x00000000 },
+	{ CS35L41_SP_RATE_CTRL,			0x00000028 },
+	{ CS35L41_SP_FORMAT,			0x18180200 },
+	{ CS35L41_SP_HIZ_CTRL,			0x00000002 },
+	{ CS35L41_SP_FRAME_TX_SLOT,		0x03020100 },
+	{ CS35L41_SP_FRAME_RX_SLOT,		0x00000100 },
+	{ CS35L41_SP_TX_WL,			0x00000018 },
+	{ CS35L41_SP_RX_WL,			0x00000018 },
+	{ CS35L41_DAC_PCM1_SRC,			0x00000008 },
+	{ CS35L41_ASP_TX1_SRC,			0x00000018 },
+	{ CS35L41_ASP_TX2_SRC,			0x00000019 },
+	{ CS35L41_ASP_TX3_SRC,			0x00000020 },
+	{ CS35L41_ASP_TX4_SRC,			0x00000021 },
+	{ CS35L41_DSP1_RX1_SRC,			0x00000008 },
+	{ CS35L41_DSP1_RX2_SRC,			0x00000009 },
+	{ CS35L41_DSP1_RX3_SRC,			0x00000018 },
+	{ CS35L41_DSP1_RX4_SRC,			0x00000019 },
+	{ CS35L41_DSP1_RX5_SRC,			0x00000020 },
+	{ CS35L41_DSP1_RX6_SRC,			0x00000021 },
+	{ CS35L41_DSP1_RX7_SRC,			0x0000003A },
+	{ CS35L41_DSP1_RX8_SRC,			0x00000001 },
+	{ CS35L41_NGATE1_SRC,			0x00000008 },
+	{ CS35L41_NGATE2_SRC,			0x00000009 },
+	{ CS35L41_AMP_DIG_VOL_CTRL,		0x00008000 },
+	{ CS35L41_CLASSH_CFG,			0x000B0405 },
+	{ CS35L41_WKFET_CFG,			0x00000111 },
+	{ CS35L41_NG_CFG,			0x00000033 },
+	{ CS35L41_AMP_GAIN_CTRL,		0x00000000 },
+	{ CS35L41_IRQ1_MASK1,			0xFFFFFFFF },
+	{ CS35L41_IRQ1_MASK2,			0xFFFFFFFF },
+	{ CS35L41_IRQ1_MASK3,			0xFFFF87FF },
+	{ CS35L41_IRQ1_MASK4,			0xFEFFFFFF },
+	{ CS35L41_GPIO1_CTRL1,			0xE1000001 },
+	{ CS35L41_GPIO2_CTRL1,			0xE1000001 },
+	{ CS35L41_MIXER_NGATE_CFG,		0x00000000 },
+	{ CS35L41_MIXER_NGATE_CH1_CFG,		0x00000303 },
+	{ CS35L41_MIXER_NGATE_CH2_CFG,		0x00000303 },
+	{ CS35L41_DSP1_CCM_CORE_CTRL,		0x00000101 },
+};
+
+static bool cs35l41_readable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case CS35L41_DEVID:
+	case CS35L41_REVID:
+	case CS35L41_FABID:
+	case CS35L41_RELID:
+	case CS35L41_OTPID:
+	case CS35L41_TEST_KEY_CTL:
+	case CS35L41_USER_KEY_CTL:
+	case CS35L41_OTP_CTRL0:
+	case CS35L41_OTP_CTRL3:
+	case CS35L41_OTP_CTRL4:
+	case CS35L41_OTP_CTRL5:
+	case CS35L41_OTP_CTRL6:
+	case CS35L41_OTP_CTRL7:
+	case CS35L41_OTP_CTRL8:
+	case CS35L41_PWR_CTRL1:
+	case CS35L41_PWR_CTRL2:
+	case CS35L41_PWR_CTRL3:
+	case CS35L41_CTRL_OVRRIDE:
+	case CS35L41_AMP_OUT_MUTE:
+	case CS35L41_PROTECT_REL_ERR_IGN:
+	case CS35L41_GPIO_PAD_CONTROL:
+	case CS35L41_JTAG_CONTROL:
+	case CS35L41_PWRMGT_CTL:
+	case CS35L41_WAKESRC_CTL:
+	case CS35L41_PWRMGT_STS:
+	case CS35L41_PLL_CLK_CTRL:
+	case CS35L41_DSP_CLK_CTRL:
+	case CS35L41_GLOBAL_CLK_CTRL:
+	case CS35L41_DATA_FS_SEL:
+	case CS35L41_TST_FS_MON0:
+	case CS35L41_MDSYNC_EN:
+	case CS35L41_MDSYNC_TX_ID:
+	case CS35L41_MDSYNC_PWR_CTRL:
+	case CS35L41_MDSYNC_DATA_TX:
+	case CS35L41_MDSYNC_TX_STATUS:
+	case CS35L41_MDSYNC_DATA_RX:
+	case CS35L41_MDSYNC_RX_STATUS:
+	case CS35L41_MDSYNC_ERR_STATUS:
+	case CS35L41_MDSYNC_SYNC_PTE2:
+	case CS35L41_MDSYNC_SYNC_PTE3:
+	case CS35L41_MDSYNC_SYNC_MSM_STATUS:
+	case CS35L41_BSTCVRT_VCTRL1:
+	case CS35L41_BSTCVRT_VCTRL2:
+	case CS35L41_BSTCVRT_PEAK_CUR:
+	case CS35L41_BSTCVRT_SFT_RAMP:
+	case CS35L41_BSTCVRT_COEFF:
+	case CS35L41_BSTCVRT_SLOPE_LBST:
+	case CS35L41_BSTCVRT_SW_FREQ:
+	case CS35L41_BSTCVRT_DCM_CTRL:
+	case CS35L41_BSTCVRT_DCM_MODE_FORCE:
+	case CS35L41_BSTCVRT_OVERVOLT_CTRL:
+	case CS35L41_VI_VOL_POL:
+	case CS35L41_DTEMP_WARN_THLD:
+	case CS35L41_DTEMP_CFG:
+	case CS35L41_DTEMP_EN:
+	case CS35L41_VPVBST_FS_SEL:
+	case CS35L41_SP_ENABLES:
+	case CS35L41_SP_RATE_CTRL:
+	case CS35L41_SP_FORMAT:
+	case CS35L41_SP_HIZ_CTRL:
+	case CS35L41_SP_FRAME_TX_SLOT:
+	case CS35L41_SP_FRAME_RX_SLOT:
+	case CS35L41_SP_TX_WL:
+	case CS35L41_SP_RX_WL:
+	case CS35L41_DAC_PCM1_SRC:
+	case CS35L41_ASP_TX1_SRC:
+	case CS35L41_ASP_TX2_SRC:
+	case CS35L41_ASP_TX3_SRC:
+	case CS35L41_ASP_TX4_SRC:
+	case CS35L41_DSP1_RX1_SRC:
+	case CS35L41_DSP1_RX2_SRC:
+	case CS35L41_DSP1_RX3_SRC:
+	case CS35L41_DSP1_RX4_SRC:
+	case CS35L41_DSP1_RX5_SRC:
+	case CS35L41_DSP1_RX6_SRC:
+	case CS35L41_DSP1_RX7_SRC:
+	case CS35L41_DSP1_RX8_SRC:
+	case CS35L41_NGATE1_SRC:
+	case CS35L41_NGATE2_SRC:
+	case CS35L41_AMP_DIG_VOL_CTRL:
+	case CS35L41_VPBR_CFG:
+	case CS35L41_VBBR_CFG:
+	case CS35L41_VPBR_STATUS:
+	case CS35L41_VBBR_STATUS:
+	case CS35L41_OVERTEMP_CFG:
+	case CS35L41_AMP_ERR_VOL:
+	case CS35L41_VOL_STATUS_TO_DSP:
+	case CS35L41_CLASSH_CFG:
+	case CS35L41_WKFET_CFG:
+	case CS35L41_NG_CFG:
+	case CS35L41_AMP_GAIN_CTRL:
+	case CS35L41_DAC_MSM_CFG:
+	case CS35L41_IRQ1_CFG:
+	case CS35L41_IRQ1_STATUS:
+	case CS35L41_IRQ1_STATUS1:
+	case CS35L41_IRQ1_STATUS2:
+	case CS35L41_IRQ1_STATUS3:
+	case CS35L41_IRQ1_STATUS4:
+	case CS35L41_IRQ1_RAW_STATUS1:
+	case CS35L41_IRQ1_RAW_STATUS2:
+	case CS35L41_IRQ1_RAW_STATUS3:
+	case CS35L41_IRQ1_RAW_STATUS4:
+	case CS35L41_IRQ1_MASK1:
+	case CS35L41_IRQ1_MASK2:
+	case CS35L41_IRQ1_MASK3:
+	case CS35L41_IRQ1_MASK4:
+	case CS35L41_IRQ1_FRC1:
+	case CS35L41_IRQ1_FRC2:
+	case CS35L41_IRQ1_FRC3:
+	case CS35L41_IRQ1_FRC4:
+	case CS35L41_IRQ1_EDGE1:
+	case CS35L41_IRQ1_EDGE4:
+	case CS35L41_IRQ1_POL1:
+	case CS35L41_IRQ1_POL2:
+	case CS35L41_IRQ1_POL3:
+	case CS35L41_IRQ1_POL4:
+	case CS35L41_IRQ1_DB3:
+	case CS35L41_IRQ2_CFG:
+	case CS35L41_IRQ2_STATUS:
+	case CS35L41_IRQ2_STATUS1:
+	case CS35L41_IRQ2_STATUS2:
+	case CS35L41_IRQ2_STATUS3:
+	case CS35L41_IRQ2_STATUS4:
+	case CS35L41_IRQ2_RAW_STATUS1:
+	case CS35L41_IRQ2_RAW_STATUS2:
+	case CS35L41_IRQ2_RAW_STATUS3:
+	case CS35L41_IRQ2_RAW_STATUS4:
+	case CS35L41_IRQ2_MASK1:
+	case CS35L41_IRQ2_MASK2:
+	case CS35L41_IRQ2_MASK3:
+	case CS35L41_IRQ2_MASK4:
+	case CS35L41_IRQ2_FRC1:
+	case CS35L41_IRQ2_FRC2:
+	case CS35L41_IRQ2_FRC3:
+	case CS35L41_IRQ2_FRC4:
+	case CS35L41_IRQ2_EDGE1:
+	case CS35L41_IRQ2_EDGE4:
+	case CS35L41_IRQ2_POL1:
+	case CS35L41_IRQ2_POL2:
+	case CS35L41_IRQ2_POL3:
+	case CS35L41_IRQ2_POL4:
+	case CS35L41_IRQ2_DB3:
+	case CS35L41_GPIO_STATUS1:
+	case CS35L41_GPIO1_CTRL1:
+	case CS35L41_GPIO2_CTRL1:
+	case CS35L41_MIXER_NGATE_CFG:
+	case CS35L41_MIXER_NGATE_CH1_CFG:
+	case CS35L41_MIXER_NGATE_CH2_CFG:
+	case CS35L41_DSP_MBOX_1 ... CS35L41_DSP_VIRT2_MBOX_8:
+	case CS35L41_CLOCK_DETECT_1:
+	case CS35L41_DIE_STS1:
+	case CS35L41_DIE_STS2:
+	case CS35L41_TEMP_CAL1:
+	case CS35L41_TEMP_CAL2:
+	case CS35L41_DSP1_TIMESTAMP_COUNT:
+	case CS35L41_DSP1_SYS_ID:
+	case CS35L41_DSP1_SYS_VERSION:
+	case CS35L41_DSP1_SYS_CORE_ID:
+	case CS35L41_DSP1_SYS_AHB_ADDR:
+	case CS35L41_DSP1_SYS_XSRAM_SIZE:
+	case CS35L41_DSP1_SYS_YSRAM_SIZE:
+	case CS35L41_DSP1_SYS_PSRAM_SIZE:
+	case CS35L41_DSP1_SYS_PM_BOOT_SIZE:
+	case CS35L41_DSP1_SYS_FEATURES:
+	case CS35L41_DSP1_SYS_FIR_FILTERS:
+	case CS35L41_DSP1_SYS_LMS_FILTERS:
+	case CS35L41_DSP1_SYS_XM_BANK_SIZE:
+	case CS35L41_DSP1_SYS_YM_BANK_SIZE:
+	case CS35L41_DSP1_SYS_PM_BANK_SIZE:
+	case CS35L41_DSP1_RX1_RATE:
+	case CS35L41_DSP1_RX2_RATE:
+	case CS35L41_DSP1_RX3_RATE:
+	case CS35L41_DSP1_RX4_RATE:
+	case CS35L41_DSP1_RX5_RATE:
+	case CS35L41_DSP1_RX6_RATE:
+	case CS35L41_DSP1_RX7_RATE:
+	case CS35L41_DSP1_RX8_RATE:
+	case CS35L41_DSP1_TX1_RATE:
+	case CS35L41_DSP1_TX2_RATE:
+	case CS35L41_DSP1_TX3_RATE:
+	case CS35L41_DSP1_TX4_RATE:
+	case CS35L41_DSP1_TX5_RATE:
+	case CS35L41_DSP1_TX6_RATE:
+	case CS35L41_DSP1_TX7_RATE:
+	case CS35L41_DSP1_TX8_RATE:
+	case CS35L41_DSP1_SCRATCH1:
+	case CS35L41_DSP1_SCRATCH2:
+	case CS35L41_DSP1_SCRATCH3:
+	case CS35L41_DSP1_SCRATCH4:
+	case CS35L41_DSP1_CCM_CORE_CTRL:
+	case CS35L41_DSP1_CCM_CLK_OVERRIDE:
+	case CS35L41_DSP1_XM_MSTR_EN:
+	case CS35L41_DSP1_XM_CORE_PRI:
+	case CS35L41_DSP1_XM_AHB_PACK_PL_PRI:
+	case CS35L41_DSP1_XM_AHB_UP_PL_PRI:
+	case CS35L41_DSP1_XM_ACCEL_PL0_PRI:
+	case CS35L41_DSP1_XM_NPL0_PRI:
+	case CS35L41_DSP1_YM_MSTR_EN:
+	case CS35L41_DSP1_YM_CORE_PRI:
+	case CS35L41_DSP1_YM_AHB_PACK_PL_PRI:
+	case CS35L41_DSP1_YM_AHB_UP_PL_PRI:
+	case CS35L41_DSP1_YM_ACCEL_PL0_PRI:
+	case CS35L41_DSP1_YM_NPL0_PRI:
+	case CS35L41_DSP1_MPU_XM_ACCESS0:
+	case CS35L41_DSP1_MPU_YM_ACCESS0:
+	case CS35L41_DSP1_MPU_WNDW_ACCESS0:
+	case CS35L41_DSP1_MPU_XREG_ACCESS0:
+	case CS35L41_DSP1_MPU_YREG_ACCESS0:
+	case CS35L41_DSP1_MPU_XM_ACCESS1:
+	case CS35L41_DSP1_MPU_YM_ACCESS1:
+	case CS35L41_DSP1_MPU_WNDW_ACCESS1:
+	case CS35L41_DSP1_MPU_XREG_ACCESS1:
+	case CS35L41_DSP1_MPU_YREG_ACCESS1:
+	case CS35L41_DSP1_MPU_XM_ACCESS2:
+	case CS35L41_DSP1_MPU_YM_ACCESS2:
+	case CS35L41_DSP1_MPU_WNDW_ACCESS2:
+	case CS35L41_DSP1_MPU_XREG_ACCESS2:
+	case CS35L41_DSP1_MPU_YREG_ACCESS2:
+	case CS35L41_DSP1_MPU_XM_ACCESS3:
+	case CS35L41_DSP1_MPU_YM_ACCESS3:
+	case CS35L41_DSP1_MPU_WNDW_ACCESS3:
+	case CS35L41_DSP1_MPU_XREG_ACCESS3:
+	case CS35L41_DSP1_MPU_YREG_ACCESS3:
+	case CS35L41_DSP1_MPU_XM_VIO_ADDR:
+	case CS35L41_DSP1_MPU_XM_VIO_STATUS:
+	case CS35L41_DSP1_MPU_YM_VIO_ADDR:
+	case CS35L41_DSP1_MPU_YM_VIO_STATUS:
+	case CS35L41_DSP1_MPU_PM_VIO_ADDR:
+	case CS35L41_DSP1_MPU_PM_VIO_STATUS:
+	case CS35L41_DSP1_MPU_LOCK_CONFIG:
+	case CS35L41_DSP1_MPU_WDT_RST_CTRL:
+	case CS35L41_OTP_TRIM_1:
+	case CS35L41_OTP_TRIM_2:
+	case CS35L41_OTP_TRIM_3:
+	case CS35L41_OTP_TRIM_4:
+	case CS35L41_OTP_TRIM_5:
+	case CS35L41_OTP_TRIM_6:
+	case CS35L41_OTP_TRIM_7:
+	case CS35L41_OTP_TRIM_8:
+	case CS35L41_OTP_TRIM_9:
+	case CS35L41_OTP_TRIM_10:
+	case CS35L41_OTP_TRIM_11:
+	case CS35L41_OTP_TRIM_12:
+	case CS35L41_OTP_TRIM_13:
+	case CS35L41_OTP_TRIM_14:
+	case CS35L41_OTP_TRIM_15:
+	case CS35L41_OTP_TRIM_16:
+	case CS35L41_OTP_TRIM_17:
+	case CS35L41_OTP_TRIM_18:
+	case CS35L41_OTP_TRIM_19:
+	case CS35L41_OTP_TRIM_20:
+	case CS35L41_OTP_TRIM_21:
+	case CS35L41_OTP_TRIM_22:
+	case CS35L41_OTP_TRIM_23:
+	case CS35L41_OTP_TRIM_24:
+	case CS35L41_OTP_TRIM_25:
+	case CS35L41_OTP_TRIM_26:
+	case CS35L41_OTP_TRIM_27:
+	case CS35L41_OTP_TRIM_28:
+	case CS35L41_OTP_TRIM_29:
+	case CS35L41_OTP_TRIM_30:
+	case CS35L41_OTP_TRIM_31:
+	case CS35L41_OTP_TRIM_32:
+	case CS35L41_OTP_TRIM_33:
+	case CS35L41_OTP_TRIM_34:
+	case CS35L41_OTP_TRIM_35:
+	case CS35L41_OTP_TRIM_36:
+	case CS35L41_OTP_MEM0 ... CS35L41_OTP_MEM31:
+	case CS35L41_DSP1_XMEM_PACK_0 ... CS35L41_DSP1_XMEM_PACK_3068:
+	case CS35L41_DSP1_XMEM_UNPACK32_0 ... CS35L41_DSP1_XMEM_UNPACK32_2046:
+	case CS35L41_DSP1_XMEM_UNPACK24_0 ... CS35L41_DSP1_XMEM_UNPACK24_4093:
+	case CS35L41_DSP1_YMEM_PACK_0 ... CS35L41_DSP1_YMEM_PACK_1532:
+	case CS35L41_DSP1_YMEM_UNPACK32_0 ... CS35L41_DSP1_YMEM_UNPACK32_1022:
+	case CS35L41_DSP1_YMEM_UNPACK24_0 ... CS35L41_DSP1_YMEM_UNPACK24_2045:
+	case CS35L41_DSP1_PMEM_0 ... CS35L41_DSP1_PMEM_5114:
+	/*test regs*/
+	case CS35L41_PLL_OVR:
+	case CS35L41_BST_TEST_DUTY:
+	case CS35L41_DIGPWM_IOCTRL:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool cs35l41_precious_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case CS35L41_TEST_KEY_CTL:
+	case CS35L41_USER_KEY_CTL:
+	case CS35L41_OTP_MEM0 ... CS35L41_OTP_MEM31:
+	case CS35L41_TST_FS_MON0:
+	case CS35L41_DSP1_XMEM_PACK_0 ... CS35L41_DSP1_XMEM_PACK_3068:
+	case CS35L41_DSP1_YMEM_PACK_0 ... CS35L41_DSP1_YMEM_PACK_1532:
+	case CS35L41_DSP1_PMEM_0 ... CS35L41_DSP1_PMEM_5114:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool cs35l41_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case CS35L41_DEVID:
+	case CS35L41_SFT_RESET:
+	case CS35L41_FABID:
+	case CS35L41_REVID:
+	case CS35L41_OTPID:
+	case CS35L41_TEST_KEY_CTL:
+	case CS35L41_USER_KEY_CTL:
+	case CS35L41_PWRMGT_CTL:
+	case CS35L41_WAKESRC_CTL:
+	case CS35L41_PWRMGT_STS:
+	case CS35L41_DTEMP_EN:
+	case CS35L41_IRQ1_STATUS:
+	case CS35L41_IRQ1_STATUS1:
+	case CS35L41_IRQ1_STATUS2:
+	case CS35L41_IRQ1_STATUS3:
+	case CS35L41_IRQ1_STATUS4:
+	case CS35L41_IRQ1_RAW_STATUS1:
+	case CS35L41_IRQ1_RAW_STATUS2:
+	case CS35L41_IRQ1_RAW_STATUS3:
+	case CS35L41_IRQ1_RAW_STATUS4:
+	case CS35L41_IRQ2_STATUS:
+	case CS35L41_IRQ2_STATUS1:
+	case CS35L41_IRQ2_STATUS2:
+	case CS35L41_IRQ2_STATUS3:
+	case CS35L41_IRQ2_STATUS4:
+	case CS35L41_IRQ2_RAW_STATUS1:
+	case CS35L41_IRQ2_RAW_STATUS2:
+	case CS35L41_IRQ2_RAW_STATUS3:
+	case CS35L41_IRQ2_RAW_STATUS4:
+	case CS35L41_GPIO_STATUS1:
+	case CS35L41_DSP_MBOX_1 ... CS35L41_DSP_VIRT2_MBOX_8:
+	case CS35L41_DSP1_XMEM_PACK_0 ... CS35L41_DSP1_XMEM_PACK_3068:
+	case CS35L41_DSP1_XMEM_UNPACK32_0 ... CS35L41_DSP1_XMEM_UNPACK32_2046:
+	case CS35L41_DSP1_XMEM_UNPACK24_0 ... CS35L41_DSP1_XMEM_UNPACK24_4093:
+	case CS35L41_DSP1_YMEM_PACK_0 ... CS35L41_DSP1_YMEM_PACK_1532:
+	case CS35L41_DSP1_YMEM_UNPACK32_0 ... CS35L41_DSP1_YMEM_UNPACK32_1022:
+	case CS35L41_DSP1_YMEM_UNPACK24_0 ... CS35L41_DSP1_YMEM_UNPACK24_2045:
+	case CS35L41_DSP1_PMEM_0 ... CS35L41_DSP1_PMEM_5114:
+	case CS35L41_DSP1_SCRATCH1:
+	case CS35L41_DSP1_SCRATCH2:
+	case CS35L41_DSP1_SCRATCH3:
+	case CS35L41_DSP1_SCRATCH4:
+	case CS35L41_DSP1_CCM_CLK_OVERRIDE ... CS35L41_DSP1_WDT_STATUS:
+	case CS35L41_OTP_MEM0 ... CS35L41_OTP_MEM31:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static const struct cs35l41_otp_packed_element_t otp_map_1[] = {
+	/* addr         shift   size */
+	{ 0x00002030,	0,	4 }, /*TRIM_OSC_FREQ_TRIM*/
+	{ 0x00002030,	7,	1 }, /*TRIM_OSC_TRIM_DONE*/
+	{ 0x0000208c,	24,	6 }, /*TST_DIGREG_VREF_TRIM*/
+	{ 0x00002090,	14,	4 }, /*TST_REF_TRIM*/
+	{ 0x00002090,	10,	4 }, /*TST_REF_TEMPCO_TRIM*/
+	{ 0x0000300C,	11,	4 }, /*PLL_LDOA_TST_VREF_TRIM*/
+	{ 0x0000394C,	23,	2 }, /*BST_ATEST_CM_VOFF*/
+	{ 0x00003950,	0,	7 }, /*BST_ATRIM_IADC_OFFSET*/
+	{ 0x00003950,	8,	7 }, /*BST_ATRIM_IADC_GAIN1*/
+	{ 0x00003950,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET1*/
+	{ 0x00003950,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN1*/
+	{ 0x00003954,	0,	7 }, /*BST_ATRIM_IADC_OFFSET2*/
+	{ 0x00003954,	8,	7 }, /*BST_ATRIM_IADC_GAIN2*/
+	{ 0x00003954,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET2*/
+	{ 0x00003954,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN2*/
+	{ 0x00003958,	0,	7 }, /*BST_ATRIM_IADC_OFFSET3*/
+	{ 0x00003958,	8,	7 }, /*BST_ATRIM_IADC_GAIN3*/
+	{ 0x00003958,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET3*/
+	{ 0x00003958,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN3*/
+	{ 0x0000395C,	0,	7 }, /*BST_ATRIM_IADC_OFFSET4*/
+	{ 0x0000395C,	8,	7 }, /*BST_ATRIM_IADC_GAIN4*/
+	{ 0x0000395C,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET4*/
+	{ 0x0000395C,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN4*/
+	{ 0x0000416C,	0,	8 }, /*VMON_GAIN_OTP_VAL*/
+	{ 0x00004160,	0,	7 }, /*VMON_OFFSET_OTP_VAL*/
+	{ 0x0000416C,	8,	8 }, /*IMON_GAIN_OTP_VAL*/
+	{ 0x00004160,	16,	10 }, /*IMON_OFFSET_OTP_VAL*/
+	{ 0x0000416C,	16,	12 }, /*VMON_CM_GAIN_OTP_VAL*/
+	{ 0x0000416C,	28,	1 }, /*VMON_CM_GAIN_SIGN_OTP_VAL*/
+	{ 0x00004170,	0,	6 }, /*IMON_CAL_TEMPCO_OTP_VAL*/
+	{ 0x00004170,	6,	1 }, /*IMON_CAL_TEMPCO_SIGN_OTP*/
+	{ 0x00004170,	8,	6 }, /*IMON_CAL_TEMPCO2_OTP_VAL*/
+	{ 0x00004170,	14,	1 }, /*IMON_CAL_TEMPCO2_DN_UPB_OTP_VAL*/
+	{ 0x00004170,	16,	9 }, /*IMON_CAL_TEMPCO_TBASE_OTP_VAL*/
+	{ 0x00004360,	0,	5 }, /*TEMP_GAIN_OTP_VAL*/
+	{ 0x00004360,	6,	9 }, /*TEMP_OFFSET_OTP_VAL*/
+	{ 0x00004448,	0,	8 }, /*VP_SARADC_OFFSET*/
+	{ 0x00004448,	8,	8 }, /*VP_GAIN_INDEX*/
+	{ 0x00004448,	16,	8 }, /*VBST_SARADC_OFFSET*/
+	{ 0x00004448,	24,	8 }, /*VBST_GAIN_INDEX*/
+	{ 0x0000444C,	0,	3 }, /*ANA_SELINVREF*/
+	{ 0x00006E30,	0,	5 }, /*GAIN_ERR_COEFF_0*/
+	{ 0x00006E30,	8,	5 }, /*GAIN_ERR_COEFF_1*/
+	{ 0x00006E30,	16,	5 }, /*GAIN_ERR_COEFF_2*/
+	{ 0x00006E30,	24,	5 }, /*GAIN_ERR_COEFF_3*/
+	{ 0x00006E34,	0,	5 }, /*GAIN_ERR_COEFF_4*/
+	{ 0x00006E34,	8,	5 }, /*GAIN_ERR_COEFF_5*/
+	{ 0x00006E34,	16,	5 }, /*GAIN_ERR_COEFF_6*/
+	{ 0x00006E34,	24,	5 }, /*GAIN_ERR_COEFF_7*/
+	{ 0x00006E38,	0,	5 }, /*GAIN_ERR_COEFF_8*/
+	{ 0x00006E38,	8,	5 }, /*GAIN_ERR_COEFF_9*/
+	{ 0x00006E38,	16,	5 }, /*GAIN_ERR_COEFF_10*/
+	{ 0x00006E38,	24,	5 }, /*GAIN_ERR_COEFF_11*/
+	{ 0x00006E3C,	0,	5 }, /*GAIN_ERR_COEFF_12*/
+	{ 0x00006E3C,	8,	5 }, /*GAIN_ERR_COEFF_13*/
+	{ 0x00006E3C,	16,	5 }, /*GAIN_ERR_COEFF_14*/
+	{ 0x00006E3C,	24,	5 }, /*GAIN_ERR_COEFF_15*/
+	{ 0x00006E40,	0,	5 }, /*GAIN_ERR_COEFF_16*/
+	{ 0x00006E40,	8,	5 }, /*GAIN_ERR_COEFF_17*/
+	{ 0x00006E40,	16,	5 }, /*GAIN_ERR_COEFF_18*/
+	{ 0x00006E40,	24,	5 }, /*GAIN_ERR_COEFF_19*/
+	{ 0x00006E44,	0,	5 }, /*GAIN_ERR_COEFF_20*/
+	{ 0x00006E48,	0,	10 }, /*VOFF_GAIN_0*/
+	{ 0x00006E48,	10,	10 }, /*VOFF_GAIN_1*/
+	{ 0x00006E48,	20,	10 }, /*VOFF_GAIN_2*/
+	{ 0x00006E4C,	0,	10 }, /*VOFF_GAIN_3*/
+	{ 0x00006E4C,	10,	10 }, /*VOFF_GAIN_4*/
+	{ 0x00006E4C,	20,	10 }, /*VOFF_GAIN_5*/
+	{ 0x00006E50,	0,	10 }, /*VOFF_GAIN_6*/
+	{ 0x00006E50,	10,	10 }, /*VOFF_GAIN_7*/
+	{ 0x00006E50,	20,	10 }, /*VOFF_GAIN_8*/
+	{ 0x00006E54,	0,	10 }, /*VOFF_GAIN_9*/
+	{ 0x00006E54,	10,	10 }, /*VOFF_GAIN_10*/
+	{ 0x00006E54,	20,	10 }, /*VOFF_GAIN_11*/
+	{ 0x00006E58,	0,	10 }, /*VOFF_GAIN_12*/
+	{ 0x00006E58,	10,	10 }, /*VOFF_GAIN_13*/
+	{ 0x00006E58,	20,	10 }, /*VOFF_GAIN_14*/
+	{ 0x00006E5C,	0,	10 }, /*VOFF_GAIN_15*/
+	{ 0x00006E5C,	10,	10 }, /*VOFF_GAIN_16*/
+	{ 0x00006E5C,	20,	10 }, /*VOFF_GAIN_17*/
+	{ 0x00006E60,	0,	10 }, /*VOFF_GAIN_18*/
+	{ 0x00006E60,	10,	10 }, /*VOFF_GAIN_19*/
+	{ 0x00006E60,	20,	10 }, /*VOFF_GAIN_20*/
+	{ 0x00006E64,	0,	10 }, /*VOFF_INT1*/
+	{ 0x00007418,	7,	5 }, /*DS_SPK_INT1_CAP_TRIM*/
+	{ 0x0000741C,	0,	5 }, /*DS_SPK_INT2_CAP_TRIM*/
+	{ 0x0000741C,	11,	4 }, /*DS_SPK_LPF_CAP_TRIM*/
+	{ 0x0000741C,	19,	4 }, /*DS_SPK_QUAN_CAP_TRIM*/
+	{ 0x00007434,	17,	1 }, /*FORCE_CAL*/
+	{ 0x00007434,	18,	7 }, /*CAL_OVERRIDE*/
+	{ 0x00007068,	0,	9 }, /*MODIX*/
+	{ 0x0000410C,	7,	1 }, /*VIMON_DLY_NOT_COMB*/
+	{ 0x0000400C,	0,	7 }, /*VIMON_DLY*/
+	{ 0x00000000,	0,	1 }, /*extra bit*/
+	{ 0x00017040,	0,	8 }, /*X_COORDINATE*/
+	{ 0x00017040,	8,	8 }, /*Y_COORDINATE*/
+	{ 0x00017040,	16,	8 }, /*WAFER_ID*/
+	{ 0x00017040,	24,	8 }, /*DVS*/
+	{ 0x00017044,	0,	24 }, /*LOT_NUMBER*/
+};
+
+static const struct cs35l41_otp_packed_element_t otp_map_2[] = {
+	/* addr         shift   size */
+	{ 0x00002030,	0,	4 }, /*TRIM_OSC_FREQ_TRIM*/
+	{ 0x00002030,	7,	1 }, /*TRIM_OSC_TRIM_DONE*/
+	{ 0x0000208c,	24,	6 }, /*TST_DIGREG_VREF_TRIM*/
+	{ 0x00002090,	14,	4 }, /*TST_REF_TRIM*/
+	{ 0x00002090,	10,	4 }, /*TST_REF_TEMPCO_TRIM*/
+	{ 0x0000300C,	11,	4 }, /*PLL_LDOA_TST_VREF_TRIM*/
+	{ 0x0000394C,	23,	2 }, /*BST_ATEST_CM_VOFF*/
+	{ 0x00003950,	0,	7 }, /*BST_ATRIM_IADC_OFFSET*/
+	{ 0x00003950,	8,	7 }, /*BST_ATRIM_IADC_GAIN1*/
+	{ 0x00003950,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET1*/
+	{ 0x00003950,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN1*/
+	{ 0x00003954,	0,	7 }, /*BST_ATRIM_IADC_OFFSET2*/
+	{ 0x00003954,	8,	7 }, /*BST_ATRIM_IADC_GAIN2*/
+	{ 0x00003954,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET2*/
+	{ 0x00003954,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN2*/
+	{ 0x00003958,	0,	7 }, /*BST_ATRIM_IADC_OFFSET3*/
+	{ 0x00003958,	8,	7 }, /*BST_ATRIM_IADC_GAIN3*/
+	{ 0x00003958,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET3*/
+	{ 0x00003958,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN3*/
+	{ 0x0000395C,	0,	7 }, /*BST_ATRIM_IADC_OFFSET4*/
+	{ 0x0000395C,	8,	7 }, /*BST_ATRIM_IADC_GAIN4*/
+	{ 0x0000395C,	16,	8 }, /*BST_ATRIM_IPKCOMP_OFFSET4*/
+	{ 0x0000395C,	24,	8 }, /*BST_ATRIM_IPKCOMP_GAIN4*/
+	{ 0x0000416C,	0,	8 }, /*VMON_GAIN_OTP_VAL*/
+	{ 0x00004160,	0,	7 }, /*VMON_OFFSET_OTP_VAL*/
+	{ 0x0000416C,	8,	8 }, /*IMON_GAIN_OTP_VAL*/
+	{ 0x00004160,	16,	10 }, /*IMON_OFFSET_OTP_VAL*/
+	{ 0x0000416C,	16,	12 }, /*VMON_CM_GAIN_OTP_VAL*/
+	{ 0x0000416C,	28,	1 }, /*VMON_CM_GAIN_SIGN_OTP_VAL*/
+	{ 0x00004170,	0,	6 }, /*IMON_CAL_TEMPCO_OTP_VAL*/
+	{ 0x00004170,	6,	1 }, /*IMON_CAL_TEMPCO_SIGN_OTP*/
+	{ 0x00004170,	8,	6 }, /*IMON_CAL_TEMPCO2_OTP_VAL*/
+	{ 0x00004170,	14,	1 }, /*IMON_CAL_TEMPCO2_DN_UPB_OTP_VAL*/
+	{ 0x00004170,	16,	9 }, /*IMON_CAL_TEMPCO_TBASE_OTP_VAL*/
+	{ 0x00004360,	0,	5 }, /*TEMP_GAIN_OTP_VAL*/
+	{ 0x00004360,	6,	9 }, /*TEMP_OFFSET_OTP_VAL*/
+	{ 0x00004448,	0,	8 }, /*VP_SARADC_OFFSET*/
+	{ 0x00004448,	8,	8 }, /*VP_GAIN_INDEX*/
+	{ 0x00004448,	16,	8 }, /*VBST_SARADC_OFFSET*/
+	{ 0x00004448,	24,	8 }, /*VBST_GAIN_INDEX*/
+	{ 0x0000444C,	0,	3 }, /*ANA_SELINVREF*/
+	{ 0x00006E30,	0,	5 }, /*GAIN_ERR_COEFF_0*/
+	{ 0x00006E30,	8,	5 }, /*GAIN_ERR_COEFF_1*/
+	{ 0x00006E30,	16,	5 }, /*GAIN_ERR_COEFF_2*/
+	{ 0x00006E30,	24,	5 }, /*GAIN_ERR_COEFF_3*/
+	{ 0x00006E34,	0,	5 }, /*GAIN_ERR_COEFF_4*/
+	{ 0x00006E34,	8,	5 }, /*GAIN_ERR_COEFF_5*/
+	{ 0x00006E34,	16,	5 }, /*GAIN_ERR_COEFF_6*/
+	{ 0x00006E34,	24,	5 }, /*GAIN_ERR_COEFF_7*/
+	{ 0x00006E38,	0,	5 }, /*GAIN_ERR_COEFF_8*/
+	{ 0x00006E38,	8,	5 }, /*GAIN_ERR_COEFF_9*/
+	{ 0x00006E38,	16,	5 }, /*GAIN_ERR_COEFF_10*/
+	{ 0x00006E38,	24,	5 }, /*GAIN_ERR_COEFF_11*/
+	{ 0x00006E3C,	0,	5 }, /*GAIN_ERR_COEFF_12*/
+	{ 0x00006E3C,	8,	5 }, /*GAIN_ERR_COEFF_13*/
+	{ 0x00006E3C,	16,	5 }, /*GAIN_ERR_COEFF_14*/
+	{ 0x00006E3C,	24,	5 }, /*GAIN_ERR_COEFF_15*/
+	{ 0x00006E40,	0,	5 }, /*GAIN_ERR_COEFF_16*/
+	{ 0x00006E40,	8,	5 }, /*GAIN_ERR_COEFF_17*/
+	{ 0x00006E40,	16,	5 }, /*GAIN_ERR_COEFF_18*/
+	{ 0x00006E40,	24,	5 }, /*GAIN_ERR_COEFF_19*/
+	{ 0x00006E44,	0,	5 }, /*GAIN_ERR_COEFF_20*/
+	{ 0x00006E48,	0,	10 }, /*VOFF_GAIN_0*/
+	{ 0x00006E48,	10,	10 }, /*VOFF_GAIN_1*/
+	{ 0x00006E48,	20,	10 }, /*VOFF_GAIN_2*/
+	{ 0x00006E4C,	0,	10 }, /*VOFF_GAIN_3*/
+	{ 0x00006E4C,	10,	10 }, /*VOFF_GAIN_4*/
+	{ 0x00006E4C,	20,	10 }, /*VOFF_GAIN_5*/
+	{ 0x00006E50,	0,	10 }, /*VOFF_GAIN_6*/
+	{ 0x00006E50,	10,	10 }, /*VOFF_GAIN_7*/
+	{ 0x00006E50,	20,	10 }, /*VOFF_GAIN_8*/
+	{ 0x00006E54,	0,	10 }, /*VOFF_GAIN_9*/
+	{ 0x00006E54,	10,	10 }, /*VOFF_GAIN_10*/
+	{ 0x00006E54,	20,	10 }, /*VOFF_GAIN_11*/
+	{ 0x00006E58,	0,	10 }, /*VOFF_GAIN_12*/
+	{ 0x00006E58,	10,	10 }, /*VOFF_GAIN_13*/
+	{ 0x00006E58,	20,	10 }, /*VOFF_GAIN_14*/
+	{ 0x00006E5C,	0,	10 }, /*VOFF_GAIN_15*/
+	{ 0x00006E5C,	10,	10 }, /*VOFF_GAIN_16*/
+	{ 0x00006E5C,	20,	10 }, /*VOFF_GAIN_17*/
+	{ 0x00006E60,	0,	10 }, /*VOFF_GAIN_18*/
+	{ 0x00006E60,	10,	10 }, /*VOFF_GAIN_19*/
+	{ 0x00006E60,	20,	10 }, /*VOFF_GAIN_20*/
+	{ 0x00006E64,	0,	10 }, /*VOFF_INT1*/
+	{ 0x00007418,	7,	5 }, /*DS_SPK_INT1_CAP_TRIM*/
+	{ 0x0000741C,	0,	5 }, /*DS_SPK_INT2_CAP_TRIM*/
+	{ 0x0000741C,	11,	4 }, /*DS_SPK_LPF_CAP_TRIM*/
+	{ 0x0000741C,	19,	4 }, /*DS_SPK_QUAN_CAP_TRIM*/
+	{ 0x00007434,	17,	1 }, /*FORCE_CAL*/
+	{ 0x00007434,	18,	7 }, /*CAL_OVERRIDE*/
+	{ 0x00007068,	0,	9 }, /*MODIX*/
+	{ 0x0000410C,	7,	1 }, /*VIMON_DLY_NOT_COMB*/
+	{ 0x0000400C,	0,	7 }, /*VIMON_DLY*/
+	{ 0x00004000,	11,	1 }, /*VMON_POL*/
+	{ 0x00017040,	0,	8 }, /*X_COORDINATE*/
+	{ 0x00017040,	8,	8 }, /*Y_COORDINATE*/
+	{ 0x00017040,	16,	8 }, /*WAFER_ID*/
+	{ 0x00017040,	24,	8 }, /*DVS*/
+	{ 0x00017044,	0,	24 }, /*LOT_NUMBER*/
+};
+
+static const struct reg_sequence cs35l41_reva0_errata_patch[] = {
+	{ 0x00003854,			 0x05180240 },
+	{ CS35L41_VIMON_SPKMON_RESYNC,	 0x00000000 },
+	{ 0x00004310,			 0x00000000 },
+	{ CS35L41_VPVBST_FS_SEL,	 0x00000000 },
+	{ CS35L41_OTP_TRIM_30,		 0x9091A1C8 },
+	{ 0x00003014,			 0x0200EE0E },
+	{ CS35L41_BSTCVRT_DCM_CTRL,	 0x00000051 },
+	{ 0x00000054,			 0x00000004 },
+	{ CS35L41_IRQ1_DB3,		 0x00000000 },
+	{ CS35L41_IRQ2_DB3,		 0x00000000 },
+	{ CS35L41_DSP1_YM_ACCEL_PL0_PRI, 0x00000000 },
+	{ CS35L41_DSP1_XM_ACCEL_PL0_PRI, 0x00000000 },
+	{ CS35L41_PWR_CTRL2,		 0x00000000 },
+	{ CS35L41_AMP_GAIN_CTRL,	 0x00000000 },
+};
+
+static const struct reg_sequence cs35l41_revb0_errata_patch[] = {
+	{ CS35L41_VIMON_SPKMON_RESYNC,	 0x00000000 },
+	{ 0x00004310,			 0x00000000 },
+	{ CS35L41_VPVBST_FS_SEL,	 0x00000000 },
+	{ CS35L41_BSTCVRT_DCM_CTRL,	 0x00000051 },
+	{ CS35L41_DSP1_YM_ACCEL_PL0_PRI, 0x00000000 },
+	{ CS35L41_DSP1_XM_ACCEL_PL0_PRI, 0x00000000 },
+	{ CS35L41_PWR_CTRL2,		 0x00000000 },
+	{ CS35L41_AMP_GAIN_CTRL,	 0x00000000 },
+};
+
+static const struct reg_sequence cs35l41_revb2_errata_patch[] = {
+	{ CS35L41_VIMON_SPKMON_RESYNC,	 0x00000000 },
+	{ 0x00004310,			 0x00000000 },
+	{ CS35L41_VPVBST_FS_SEL,	 0x00000000 },
+	{ CS35L41_BSTCVRT_DCM_CTRL,	 0x00000051 },
+	{ CS35L41_DSP1_YM_ACCEL_PL0_PRI, 0x00000000 },
+	{ CS35L41_DSP1_XM_ACCEL_PL0_PRI, 0x00000000 },
+	{ CS35L41_PWR_CTRL2,		 0x00000000 },
+	{ CS35L41_AMP_GAIN_CTRL,	 0x00000000 },
+};
+
+static const struct cs35l41_otp_map_element_t cs35l41_otp_map_map[] = {
+	{
+		.id = 0x01,
+		.map = otp_map_1,
+		.num_elements = ARRAY_SIZE(otp_map_1),
+		.bit_offset = 16,
+		.word_offset = 2,
+	},
+	{
+		.id = 0x02,
+		.map = otp_map_2,
+		.num_elements = ARRAY_SIZE(otp_map_2),
+		.bit_offset = 16,
+		.word_offset = 2,
+	},
+	{
+		.id = 0x03,
+		.map = otp_map_2,
+		.num_elements = ARRAY_SIZE(otp_map_2),
+		.bit_offset = 16,
+		.word_offset = 2,
+	},
+	{
+		.id = 0x06,
+		.map = otp_map_2,
+		.num_elements = ARRAY_SIZE(otp_map_2),
+		.bit_offset = 16,
+		.word_offset = 2,
+	},
+	{
+		.id = 0x08,
+		.map = otp_map_1,
+		.num_elements = ARRAY_SIZE(otp_map_1),
+		.bit_offset = 16,
+		.word_offset = 2,
+	},
+};
+
+struct regmap_config cs35l41_regmap_i2c = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = CS35L41_REGSTRIDE,
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_BIG,
+	.max_register = CS35L41_LASTREG,
+	.reg_defaults = cs35l41_reg,
+	.num_reg_defaults = ARRAY_SIZE(cs35l41_reg),
+	.volatile_reg = cs35l41_volatile_reg,
+	.readable_reg = cs35l41_readable_reg,
+	.precious_reg = cs35l41_precious_reg,
+	.cache_type = REGCACHE_RBTREE,
+};
+EXPORT_SYMBOL_GPL(cs35l41_regmap_i2c);
+
+struct regmap_config cs35l41_regmap_spi = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.pad_bits = 16,
+	.reg_stride = CS35L41_REGSTRIDE,
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_BIG,
+	.max_register = CS35L41_LASTREG,
+	.reg_defaults = cs35l41_reg,
+	.num_reg_defaults = ARRAY_SIZE(cs35l41_reg),
+	.volatile_reg = cs35l41_volatile_reg,
+	.readable_reg = cs35l41_readable_reg,
+	.precious_reg = cs35l41_precious_reg,
+	.cache_type = REGCACHE_RBTREE,
+};
+EXPORT_SYMBOL_GPL(cs35l41_regmap_spi);
+
+static const struct cs35l41_otp_map_element_t *cs35l41_find_otp_map(u32 otp_id)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cs35l41_otp_map_map); i++) {
+		if (cs35l41_otp_map_map[i].id == otp_id)
+			return &cs35l41_otp_map_map[i];
+	}
+
+	return NULL;
+}
+
+int cs35l41_test_key_unlock(struct device *dev, struct regmap *regmap)
+{
+	static const struct reg_sequence unlock[] = {
+		{ CS35L41_TEST_KEY_CTL, 0x00000055 },
+		{ CS35L41_TEST_KEY_CTL, 0x000000AA },
+	};
+	int ret;
+
+	ret = regmap_multi_reg_write(regmap, unlock, ARRAY_SIZE(unlock));
+	if (ret)
+		dev_err(dev, "Failed to unlock test key: %d\n", ret);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cs35l41_test_key_unlock);
+
+int cs35l41_test_key_lock(struct device *dev, struct regmap *regmap)
+{
+	static const struct reg_sequence unlock[] = {
+		{ CS35L41_TEST_KEY_CTL, 0x000000CC },
+		{ CS35L41_TEST_KEY_CTL, 0x00000033 },
+	};
+	int ret;
+
+	ret = regmap_multi_reg_write(regmap, unlock, ARRAY_SIZE(unlock));
+	if (ret)
+		dev_err(dev, "Failed to lock test key: %d\n", ret);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cs35l41_test_key_lock);
+
+/* Must be called with the TEST_KEY unlocked */
+int cs35l41_otp_unpack(struct device *dev, struct regmap *regmap)
+{
+	const struct cs35l41_otp_map_element_t *otp_map_match;
+	const struct cs35l41_otp_packed_element_t *otp_map;
+	int bit_offset, word_offset, ret, i;
+	unsigned int bit_sum = 8;
+	u32 otp_val, otp_id_reg;
+	u32 *otp_mem;
+
+	otp_mem = kmalloc_array(CS35L41_OTP_SIZE_WORDS, sizeof(*otp_mem), GFP_KERNEL);
+	if (!otp_mem)
+		return -ENOMEM;
+
+	ret = regmap_read(regmap, CS35L41_OTPID, &otp_id_reg);
+	if (ret) {
+		dev_err(dev, "Read OTP ID failed: %d\n", ret);
+		goto err_otp_unpack;
+	}
+
+	otp_map_match = cs35l41_find_otp_map(otp_id_reg);
+
+	if (!otp_map_match) {
+		dev_err(dev, "OTP Map matching ID %d not found\n", otp_id_reg);
+		ret = -EINVAL;
+		goto err_otp_unpack;
+	}
+
+	ret = regmap_bulk_read(regmap, CS35L41_OTP_MEM0, otp_mem, CS35L41_OTP_SIZE_WORDS);
+	if (ret) {
+		dev_err(dev, "Read OTP Mem failed: %d\n", ret);
+		goto err_otp_unpack;
+	}
+
+	otp_map = otp_map_match->map;
+
+	bit_offset = otp_map_match->bit_offset;
+	word_offset = otp_map_match->word_offset;
+
+	for (i = 0; i < otp_map_match->num_elements; i++) {
+		dev_dbg(dev, "bitoffset= %d, word_offset=%d, bit_sum mod 32=%d, otp_map[i].size = %u\n",
+			bit_offset, word_offset, bit_sum % 32, otp_map[i].size);
+		if (bit_offset + otp_map[i].size - 1 >= 32) {
+			otp_val = (otp_mem[word_offset] &
+					GENMASK(31, bit_offset)) >> bit_offset;
+			otp_val |= (otp_mem[++word_offset] &
+					GENMASK(bit_offset + otp_map[i].size - 33, 0)) <<
+					(32 - bit_offset);
+			bit_offset += otp_map[i].size - 32;
+		} else {
+			otp_val = (otp_mem[word_offset] &
+				   GENMASK(bit_offset + otp_map[i].size - 1, bit_offset)
+				  ) >> bit_offset;
+			bit_offset += otp_map[i].size;
+		}
+		bit_sum += otp_map[i].size;
+
+		if (bit_offset == 32) {
+			bit_offset = 0;
+			word_offset++;
+		}
+
+		if (otp_map[i].reg != 0) {
+			ret = regmap_update_bits(regmap, otp_map[i].reg,
+						 GENMASK(otp_map[i].shift + otp_map[i].size - 1,
+							 otp_map[i].shift),
+						 otp_val << otp_map[i].shift);
+			if (ret < 0) {
+				dev_err(dev, "Write OTP val failed: %d\n", ret);
+				goto err_otp_unpack;
+			}
+		}
+	}
+
+	ret = 0;
+
+err_otp_unpack:
+	kfree(otp_mem);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cs35l41_otp_unpack);
+
+/* Must be called with the TEST_KEY unlocked */
+int cs35l41_register_errata_patch(struct device *dev, struct regmap *reg, unsigned int reg_revid)
+{
+	char *rev;
+	int ret;
+
+	switch (reg_revid) {
+	case CS35L41_REVID_A0:
+		ret = regmap_register_patch(reg, cs35l41_reva0_errata_patch,
+					    ARRAY_SIZE(cs35l41_reva0_errata_patch));
+		rev = "A0";
+		break;
+	case CS35L41_REVID_B0:
+		ret = regmap_register_patch(reg, cs35l41_revb0_errata_patch,
+					    ARRAY_SIZE(cs35l41_revb0_errata_patch));
+		rev = "B0";
+		break;
+	case CS35L41_REVID_B2:
+		ret = regmap_register_patch(reg, cs35l41_revb2_errata_patch,
+					    ARRAY_SIZE(cs35l41_revb2_errata_patch));
+		rev = "B2";
+		break;
+	default:
+		ret = -EINVAL;
+		rev = "XX";
+		break;
+	}
+
+	if (ret)
+		dev_err(dev, "Failed to apply %s errata patch: %d\n", rev, ret);
+
+	ret = regmap_write(reg, CS35L41_DSP1_CCM_CORE_CTRL, 0);
+	if (ret < 0)
+		dev_err(dev, "Write CCM_CORE_CTRL failed: %d\n", ret);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cs35l41_register_errata_patch);
+
+int cs35l41_set_channels(struct device *dev, struct regmap *reg,
+			 unsigned int tx_num, unsigned int *tx_slot,
+			 unsigned int rx_num, unsigned int *rx_slot)
+{
+	unsigned int val, mask;
+	int i;
+
+	if (tx_num > 4 || rx_num > 2)
+		return -EINVAL;
+
+	val = 0;
+	mask = 0;
+	for (i = 0; i < rx_num; i++) {
+		dev_dbg(dev, "rx slot %d position = %d\n", i, rx_slot[i]);
+		val |= rx_slot[i] << (i * 8);
+		mask |= 0x3F << (i * 8);
+	}
+	regmap_update_bits(reg, CS35L41_SP_FRAME_RX_SLOT, mask, val);
+
+	val = 0;
+	mask = 0;
+	for (i = 0; i < tx_num; i++) {
+		dev_dbg(dev, "tx slot %d position = %d\n", i, tx_slot[i]);
+		val |= tx_slot[i] << (i * 8);
+		mask |= 0x3F << (i * 8);
+	}
+	regmap_update_bits(reg, CS35L41_SP_FRAME_TX_SLOT, mask, val);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cs35l41_set_channels);
+
+static const unsigned char cs35l41_bst_k1_table[4][5] = {
+	{ 0x24, 0x32, 0x32, 0x4F, 0x57 },
+	{ 0x24, 0x32, 0x32, 0x4F, 0x57 },
+	{ 0x40, 0x32, 0x32, 0x4F, 0x57 },
+	{ 0x40, 0x32, 0x32, 0x4F, 0x57 }
+};
+
+static const unsigned char cs35l41_bst_k2_table[4][5] = {
+	{ 0x24, 0x49, 0x66, 0xA3, 0xEA },
+	{ 0x24, 0x49, 0x66, 0xA3, 0xEA },
+	{ 0x48, 0x49, 0x66, 0xA3, 0xEA },
+	{ 0x48, 0x49, 0x66, 0xA3, 0xEA }
+};
+
+static const unsigned char cs35l41_bst_slope_table[4] = {
+	0x75, 0x6B, 0x3B, 0x28
+};
+
+
+int cs35l41_boost_config(struct device *dev, struct regmap *regmap, int boost_ind, int boost_cap,
+			 int boost_ipk)
+{
+	unsigned char bst_lbst_val, bst_cbst_range, bst_ipk_scaled;
+	int ret;
+
+	switch (boost_ind) {
+	case 1000:	/* 1.0 uH */
+		bst_lbst_val = 0;
+		break;
+	case 1200:	/* 1.2 uH */
+		bst_lbst_val = 1;
+		break;
+	case 1500:	/* 1.5 uH */
+		bst_lbst_val = 2;
+		break;
+	case 2200:	/* 2.2 uH */
+		bst_lbst_val = 3;
+		break;
+	default:
+		dev_err(dev, "Invalid boost inductor value: %d nH\n", boost_ind);
+		return -EINVAL;
+	}
+
+	switch (boost_cap) {
+	case 0 ... 19:
+		bst_cbst_range = 0;
+		break;
+	case 20 ... 50:
+		bst_cbst_range = 1;
+		break;
+	case 51 ... 100:
+		bst_cbst_range = 2;
+		break;
+	case 101 ... 200:
+		bst_cbst_range = 3;
+		break;
+	default:	/* 201 uF and greater */
+		bst_cbst_range = 4;
+	}
+
+	ret = regmap_update_bits(regmap, CS35L41_BSTCVRT_COEFF,
+				 CS35L41_BST_K1_MASK | CS35L41_BST_K2_MASK,
+				 cs35l41_bst_k1_table[bst_lbst_val][bst_cbst_range]
+					<< CS35L41_BST_K1_SHIFT |
+				 cs35l41_bst_k2_table[bst_lbst_val][bst_cbst_range]
+					<< CS35L41_BST_K2_SHIFT);
+	if (ret) {
+		dev_err(dev, "Failed to write boost coefficients: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(regmap, CS35L41_BSTCVRT_SLOPE_LBST,
+				 CS35L41_BST_SLOPE_MASK | CS35L41_BST_LBST_VAL_MASK,
+				 cs35l41_bst_slope_table[bst_lbst_val]
+					<< CS35L41_BST_SLOPE_SHIFT |
+				 bst_lbst_val << CS35L41_BST_LBST_VAL_SHIFT);
+	if (ret) {
+		dev_err(dev, "Failed to write boost slope/inductor value: %d\n", ret);
+		return ret;
+	}
+
+	if (boost_ipk < 1600 || boost_ipk > 4500) {
+		dev_err(dev, "Invalid boost inductor peak current: %d mA\n", boost_ipk);
+		return -EINVAL;
+	}
+	bst_ipk_scaled = ((boost_ipk - 1600) / 50) + 0x10;
+
+	ret = regmap_update_bits(regmap, CS35L41_BSTCVRT_PEAK_CUR, CS35L41_BST_IPK_MASK,
+				 bst_ipk_scaled << CS35L41_BST_IPK_SHIFT);
+	if (ret) {
+		dev_err(dev, "Failed to write boost inductor peak current: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cs35l41_boost_config);
+
+MODULE_DESCRIPTION("CS35L41 library");
+MODULE_AUTHOR("David Rhodes, Cirrus Logic Inc, <david.rhodes@cirrus.com>");
+MODULE_AUTHOR("Lucas Tanure, Cirrus Logic Inc, <tanureal@opensource.cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l41-spi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l41-spi.c
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// cs35l41-spi.c -- CS35l41 SPI driver
+//
+// Copyright 2017-2021 Cirrus Logic, Inc.
+//
+// Author: David Rhodes	<david.rhodes@cirrus.com>
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include "cs35l41.h"
+
+static const struct spi_device_id cs35l41_id_spi[] = {
+	{ "cs35l40", 0 },
+	{ "cs35l41", 0 },
+	{ "cs35l51", 0 },
+	{ "cs35l53", 0 },
+	{}
+};
+
+MODULE_DEVICE_TABLE(spi, cs35l41_id_spi);
+
+static int cs35l41_spi_probe(struct spi_device *spi)
+{
+	const struct regmap_config *regmap_config = &cs35l41_regmap_spi;
+	struct cs35l41_platform_data *pdata = dev_get_platdata(&spi->dev);
+	struct cs35l41_private *cs35l41;
+	int ret;
+
+	cs35l41 = devm_kzalloc(&spi->dev, sizeof(struct cs35l41_private), GFP_KERNEL);
+	if (!cs35l41)
+		return -ENOMEM;
+
+	spi->max_speed_hz = CS35L41_SPI_MAX_FREQ;
+	spi_setup(spi);
+
+	spi_set_drvdata(spi, cs35l41);
+	cs35l41->regmap = devm_regmap_init_spi(spi, regmap_config);
+	if (IS_ERR(cs35l41->regmap)) {
+		ret = PTR_ERR(cs35l41->regmap);
+		dev_err(&spi->dev, "Failed to allocate register map: %d\n", ret);
+		return ret;
+	}
+
+	cs35l41->dev = &spi->dev;
+	cs35l41->irq = spi->irq;
+
+	return cs35l41_probe(cs35l41, pdata);
+}
+
+static int cs35l41_spi_remove(struct spi_device *spi)
+{
+	struct cs35l41_private *cs35l41 = spi_get_drvdata(spi);
+
+	cs35l41_remove(cs35l41);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id cs35l41_of_match[] = {
+	{ .compatible = "cirrus,cs35l40" },
+	{ .compatible = "cirrus,cs35l41" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, cs35l41_of_match);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id cs35l41_acpi_match[] = {
+	{ "CSC3541", 0 }, /* Cirrus Logic PnP ID + part ID */
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, cs35l41_acpi_match);
+#endif
+
+static struct spi_driver cs35l41_spi_driver = {
+	.driver = {
+		.name		= "cs35l41",
+		.pm		= &cs35l41_pm_ops,
+		.of_match_table = of_match_ptr(cs35l41_of_match),
+		.acpi_match_table = ACPI_PTR(cs35l41_acpi_match),
+	},
+	.id_table	= cs35l41_id_spi,
+	.probe		= cs35l41_spi_probe,
+	.remove		= cs35l41_spi_remove,
+};
+
+module_spi_driver(cs35l41_spi_driver);
+
+MODULE_DESCRIPTION("SPI CS35L41 driver");
+MODULE_AUTHOR("David Rhodes, Cirrus Logic Inc, <david.rhodes@cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l41.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l41.c
@@ -0,0 +1,1596 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// cs35l41.c -- CS35l41 ALSA SoC audio driver
+//
+// Copyright 2017-2021 Cirrus Logic, Inc.
+//
+// Author: David Rhodes <david.rhodes@cirrus.com>
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/of_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <sound/initval.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/soc-dapm.h>
+#include <sound/tlv.h>
+
+#include "cs35l41.h"
+
+static const char * const cs35l41_supplies[CS35L41_NUM_SUPPLIES] = {
+	"VA",
+	"VP",
+};
+
+struct cs35l41_pll_sysclk_config {
+	int freq;
+	int clk_cfg;
+};
+
+static const struct cs35l41_pll_sysclk_config cs35l41_pll_sysclk[] = {
+	{ 32768,	0x00 },
+	{ 8000,		0x01 },
+	{ 11025,	0x02 },
+	{ 12000,	0x03 },
+	{ 16000,	0x04 },
+	{ 22050,	0x05 },
+	{ 24000,	0x06 },
+	{ 32000,	0x07 },
+	{ 44100,	0x08 },
+	{ 48000,	0x09 },
+	{ 88200,	0x0A },
+	{ 96000,	0x0B },
+	{ 128000,	0x0C },
+	{ 176400,	0x0D },
+	{ 192000,	0x0E },
+	{ 256000,	0x0F },
+	{ 352800,	0x10 },
+	{ 384000,	0x11 },
+	{ 512000,	0x12 },
+	{ 705600,	0x13 },
+	{ 750000,	0x14 },
+	{ 768000,	0x15 },
+	{ 1000000,	0x16 },
+	{ 1024000,	0x17 },
+	{ 1200000,	0x18 },
+	{ 1411200,	0x19 },
+	{ 1500000,	0x1A },
+	{ 1536000,	0x1B },
+	{ 2000000,	0x1C },
+	{ 2048000,	0x1D },
+	{ 2400000,	0x1E },
+	{ 2822400,	0x1F },
+	{ 3000000,	0x20 },
+	{ 3072000,	0x21 },
+	{ 3200000,	0x22 },
+	{ 4000000,	0x23 },
+	{ 4096000,	0x24 },
+	{ 4800000,	0x25 },
+	{ 5644800,	0x26 },
+	{ 6000000,	0x27 },
+	{ 6144000,	0x28 },
+	{ 6250000,	0x29 },
+	{ 6400000,	0x2A },
+	{ 6500000,	0x2B },
+	{ 6750000,	0x2C },
+	{ 7526400,	0x2D },
+	{ 8000000,	0x2E },
+	{ 8192000,	0x2F },
+	{ 9600000,	0x30 },
+	{ 11289600,	0x31 },
+	{ 12000000,	0x32 },
+	{ 12288000,	0x33 },
+	{ 12500000,	0x34 },
+	{ 12800000,	0x35 },
+	{ 13000000,	0x36 },
+	{ 13500000,	0x37 },
+	{ 19200000,	0x38 },
+	{ 22579200,	0x39 },
+	{ 24000000,	0x3A },
+	{ 24576000,	0x3B },
+	{ 25000000,	0x3C },
+	{ 25600000,	0x3D },
+	{ 26000000,	0x3E },
+	{ 27000000,	0x3F },
+};
+
+struct cs35l41_fs_mon_config {
+	int freq;
+	unsigned int fs1;
+	unsigned int fs2;
+};
+
+static const struct cs35l41_fs_mon_config cs35l41_fs_mon[] = {
+	{ 32768,	2254,	3754 },
+	{ 8000,		9220,	15364 },
+	{ 11025,	6148,	10244 },
+	{ 12000,	6148,	10244 },
+	{ 16000,	4612,	7684 },
+	{ 22050,	3076,	5124 },
+	{ 24000,	3076,	5124 },
+	{ 32000,	2308,	3844 },
+	{ 44100,	1540,	2564 },
+	{ 48000,	1540,	2564 },
+	{ 88200,	772,	1284 },
+	{ 96000,	772,	1284 },
+	{ 128000,	580,	964 },
+	{ 176400,	388,	644 },
+	{ 192000,	388,	644 },
+	{ 256000,	292,	484 },
+	{ 352800,	196,	324 },
+	{ 384000,	196,	324 },
+	{ 512000,	148,	244 },
+	{ 705600,	100,	164 },
+	{ 750000,	100,	164 },
+	{ 768000,	100,	164 },
+	{ 1000000,	76,	124 },
+	{ 1024000,	76,	124 },
+	{ 1200000,	64,	104 },
+	{ 1411200,	52,	84 },
+	{ 1500000,	52,	84 },
+	{ 1536000,	52,	84 },
+	{ 2000000,	40,	64 },
+	{ 2048000,	40,	64 },
+	{ 2400000,	34,	54 },
+	{ 2822400,	28,	44 },
+	{ 3000000,	28,	44 },
+	{ 3072000,	28,	44 },
+	{ 3200000,	27,	42 },
+	{ 4000000,	22,	34 },
+	{ 4096000,	22,	34 },
+	{ 4800000,	19,	29 },
+	{ 5644800,	16,	24 },
+	{ 6000000,	16,	24 },
+	{ 6144000,	16,	24 },
+};
+
+static int cs35l41_get_fs_mon_config_index(int freq)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cs35l41_fs_mon); i++) {
+		if (cs35l41_fs_mon[i].freq == freq)
+			return i;
+	}
+
+	return -EINVAL;
+}
+
+static const DECLARE_TLV_DB_RANGE(dig_vol_tlv,
+		0, 0, TLV_DB_SCALE_ITEM(TLV_DB_GAIN_MUTE, 0, 1),
+		1, 913, TLV_DB_MINMAX_ITEM(-10200, 1200));
+static DECLARE_TLV_DB_SCALE(amp_gain_tlv, 0, 1, 1);
+
+static const struct snd_kcontrol_new dre_ctrl =
+	SOC_DAPM_SINGLE("Switch", CS35L41_PWR_CTRL3, 20, 1, 0);
+
+static const char * const cs35l41_pcm_sftramp_text[] =  {
+	"Off", ".5ms", "1ms", "2ms", "4ms", "8ms", "15ms", "30ms"
+};
+
+static SOC_ENUM_SINGLE_DECL(pcm_sft_ramp,
+			    CS35L41_AMP_DIG_VOL_CTRL, 0,
+			    cs35l41_pcm_sftramp_text);
+
+static int cs35l41_dsp_preload_ev(struct snd_soc_dapm_widget *w,
+				  struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(component);
+	int ret;
+
+	switch (event) {
+	case SND_SOC_DAPM_PRE_PMU:
+		if (cs35l41->dsp.booted)
+			return 0;
+
+		return wm_adsp_early_event(w, kcontrol, event);
+	case SND_SOC_DAPM_PRE_PMD:
+		if (cs35l41->dsp.preloaded)
+			return 0;
+
+		if (cs35l41->dsp.running) {
+			ret = wm_adsp_event(w, kcontrol, event);
+			if (ret)
+				return ret;
+		}
+
+		return wm_adsp_early_event(w, kcontrol, event);
+	default:
+		return 0;
+	}
+}
+
+static bool cs35l41_check_cspl_mbox_sts(enum cs35l41_cspl_mbox_cmd cmd,
+					enum cs35l41_cspl_mbox_status sts)
+{
+	switch (cmd) {
+	case CSPL_MBOX_CMD_NONE:
+	case CSPL_MBOX_CMD_UNKNOWN_CMD:
+		return true;
+	case CSPL_MBOX_CMD_PAUSE:
+	case CSPL_MBOX_CMD_OUT_OF_HIBERNATE:
+		return (sts == CSPL_MBOX_STS_PAUSED);
+	case CSPL_MBOX_CMD_RESUME:
+		return (sts == CSPL_MBOX_STS_RUNNING);
+	case CSPL_MBOX_CMD_REINIT:
+		return (sts == CSPL_MBOX_STS_RUNNING);
+	case CSPL_MBOX_CMD_STOP_PRE_REINIT:
+		return (sts == CSPL_MBOX_STS_RDY_FOR_REINIT);
+	default:
+		return false;
+	}
+}
+
+static int cs35l41_set_cspl_mbox_cmd(struct cs35l41_private *cs35l41,
+				     enum cs35l41_cspl_mbox_cmd cmd)
+{
+	unsigned int sts = 0, i;
+	int ret;
+
+	// Set mailbox cmd
+	ret = regmap_write(cs35l41->regmap, CS35L41_DSP_VIRT1_MBOX_1, cmd);
+	if (ret < 0) {
+		if (cmd != CSPL_MBOX_CMD_OUT_OF_HIBERNATE)
+			dev_err(cs35l41->dev, "Failed to write MBOX: %d\n", ret);
+		return ret;
+	}
+
+	// Read mailbox status and verify it is appropriate for the given cmd
+	for (i = 0; i < 5; i++) {
+		usleep_range(1000, 1100);
+
+		ret = regmap_read(cs35l41->regmap, CS35L41_DSP_MBOX_2, &sts);
+		if (ret < 0) {
+			dev_err(cs35l41->dev, "Failed to read MBOX STS: %d\n", ret);
+			continue;
+		}
+
+		if (!cs35l41_check_cspl_mbox_sts(cmd, sts)) {
+			dev_dbg(cs35l41->dev,
+				"[%u] cmd %u returned invalid sts %u",
+				i, cmd, sts);
+		} else {
+			return 0;
+		}
+	}
+
+	dev_err(cs35l41->dev,
+		"Failed to set mailbox cmd %u (status %u)\n",
+		cmd, sts);
+
+	return -ENOMSG;
+}
+
+static int cs35l41_dsp_audio_ev(struct snd_soc_dapm_widget *w,
+				struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(component);
+	unsigned int fw_status;
+	int ret;
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMU:
+		if (!cs35l41->dsp.running)
+			return wm_adsp_event(w, kcontrol, event);
+
+		ret = regmap_read(cs35l41->regmap, CS35L41_DSP_MBOX_2, &fw_status);
+		if (ret < 0) {
+			dev_err(cs35l41->dev,
+				"Failed to read firmware status: %d\n", ret);
+			return ret;
+		}
+
+		switch (fw_status) {
+		case CSPL_MBOX_STS_RUNNING:
+		case CSPL_MBOX_STS_PAUSED:
+			break;
+		default:
+			dev_err(cs35l41->dev, "Firmware status is invalid: %u\n",
+				fw_status);
+			return -EINVAL;
+		}
+
+		return cs35l41_set_cspl_mbox_cmd(cs35l41, CSPL_MBOX_CMD_RESUME);
+	case SND_SOC_DAPM_PRE_PMD:
+		return cs35l41_set_cspl_mbox_cmd(cs35l41, CSPL_MBOX_CMD_PAUSE);
+	default:
+		return 0;
+	}
+}
+
+static const char * const cs35l41_pcm_source_texts[] = {"ASP", "DSP"};
+static const unsigned int cs35l41_pcm_source_values[] = {0x08, 0x32};
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_pcm_source_enum,
+				  CS35L41_DAC_PCM1_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_pcm_source_texts,
+				  cs35l41_pcm_source_values);
+
+static const struct snd_kcontrol_new pcm_source_mux =
+	SOC_DAPM_ENUM("PCM Source", cs35l41_pcm_source_enum);
+
+static const char * const cs35l41_tx_input_texts[] = {
+	"Zero", "ASPRX1", "ASPRX2", "VMON", "IMON",
+	"VPMON", "VBSTMON", "DSPTX1", "DSPTX2"
+};
+
+static const unsigned int cs35l41_tx_input_values[] = {
+	0x00, CS35L41_INPUT_SRC_ASPRX1, CS35L41_INPUT_SRC_ASPRX2,
+	CS35L41_INPUT_SRC_VMON, CS35L41_INPUT_SRC_IMON, CS35L41_INPUT_SRC_VPMON,
+	CS35L41_INPUT_SRC_VBSTMON, CS35L41_INPUT_DSP_TX1, CS35L41_INPUT_DSP_TX2
+};
+
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_asptx1_enum,
+				  CS35L41_ASP_TX1_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_tx_input_texts,
+				  cs35l41_tx_input_values);
+
+static const struct snd_kcontrol_new asp_tx1_mux =
+	SOC_DAPM_ENUM("ASPTX1 SRC", cs35l41_asptx1_enum);
+
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_asptx2_enum,
+				  CS35L41_ASP_TX2_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_tx_input_texts,
+				  cs35l41_tx_input_values);
+
+static const struct snd_kcontrol_new asp_tx2_mux =
+	SOC_DAPM_ENUM("ASPTX2 SRC", cs35l41_asptx2_enum);
+
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_asptx3_enum,
+				  CS35L41_ASP_TX3_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_tx_input_texts,
+				  cs35l41_tx_input_values);
+
+static const struct snd_kcontrol_new asp_tx3_mux =
+	SOC_DAPM_ENUM("ASPTX3 SRC", cs35l41_asptx3_enum);
+
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_asptx4_enum,
+				  CS35L41_ASP_TX4_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_tx_input_texts,
+				  cs35l41_tx_input_values);
+
+static const struct snd_kcontrol_new asp_tx4_mux =
+	SOC_DAPM_ENUM("ASPTX4 SRC", cs35l41_asptx4_enum);
+
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_dsprx1_enum,
+				  CS35L41_DSP1_RX1_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_tx_input_texts,
+				  cs35l41_tx_input_values);
+
+static const struct snd_kcontrol_new dsp_rx1_mux =
+	SOC_DAPM_ENUM("DSPRX1 SRC", cs35l41_dsprx1_enum);
+
+static SOC_VALUE_ENUM_SINGLE_DECL(cs35l41_dsprx2_enum,
+				  CS35L41_DSP1_RX2_SRC,
+				  0, CS35L41_ASP_SOURCE_MASK,
+				  cs35l41_tx_input_texts,
+				  cs35l41_tx_input_values);
+
+static const struct snd_kcontrol_new dsp_rx2_mux =
+	SOC_DAPM_ENUM("DSPRX2 SRC", cs35l41_dsprx2_enum);
+
+static const struct snd_kcontrol_new cs35l41_aud_controls[] = {
+	SOC_SINGLE_SX_TLV("Digital PCM Volume", CS35L41_AMP_DIG_VOL_CTRL,
+			  3, 0x4CF, 0x391, dig_vol_tlv),
+	SOC_SINGLE_TLV("Analog PCM Volume", CS35L41_AMP_GAIN_CTRL, 5, 0x14, 0,
+		       amp_gain_tlv),
+	SOC_ENUM("PCM Soft Ramp", pcm_sft_ramp),
+	SOC_SINGLE("HW Noise Gate Enable", CS35L41_NG_CFG, 8, 63, 0),
+	SOC_SINGLE("HW Noise Gate Delay", CS35L41_NG_CFG, 4, 7, 0),
+	SOC_SINGLE("HW Noise Gate Threshold", CS35L41_NG_CFG, 0, 7, 0),
+	SOC_SINGLE("Aux Noise Gate CH1 Enable",
+		   CS35L41_MIXER_NGATE_CH1_CFG, 16, 1, 0),
+	SOC_SINGLE("Aux Noise Gate CH1 Entry Delay",
+		   CS35L41_MIXER_NGATE_CH1_CFG, 8, 15, 0),
+	SOC_SINGLE("Aux Noise Gate CH1 Threshold",
+		   CS35L41_MIXER_NGATE_CH1_CFG, 0, 7, 0),
+	SOC_SINGLE("Aux Noise Gate CH2 Entry Delay",
+		   CS35L41_MIXER_NGATE_CH2_CFG, 8, 15, 0),
+	SOC_SINGLE("Aux Noise Gate CH2 Enable",
+		   CS35L41_MIXER_NGATE_CH2_CFG, 16, 1, 0),
+	SOC_SINGLE("Aux Noise Gate CH2 Threshold",
+		   CS35L41_MIXER_NGATE_CH2_CFG, 0, 7, 0),
+	SOC_SINGLE("SCLK Force", CS35L41_SP_FORMAT, CS35L41_SCLK_FRC_SHIFT, 1, 0),
+	SOC_SINGLE("LRCLK Force", CS35L41_SP_FORMAT, CS35L41_LRCLK_FRC_SHIFT, 1, 0),
+	SOC_SINGLE("Invert Class D", CS35L41_AMP_DIG_VOL_CTRL,
+		   CS35L41_AMP_INV_PCM_SHIFT, 1, 0),
+	SOC_SINGLE("Amp Gain ZC", CS35L41_AMP_GAIN_CTRL,
+		   CS35L41_AMP_GAIN_ZC_SHIFT, 1, 0),
+	WM_ADSP2_PRELOAD_SWITCH("DSP1", 1),
+	WM_ADSP_FW_CONTROL("DSP1", 0),
+};
+
+static irqreturn_t cs35l41_irq(int irq, void *data)
+{
+	struct cs35l41_private *cs35l41 = data;
+	unsigned int status[4] = { 0, 0, 0, 0 };
+	unsigned int masks[4] = { 0, 0, 0, 0 };
+	int ret = IRQ_NONE;
+	unsigned int i;
+
+	pm_runtime_get_sync(cs35l41->dev);
+
+	for (i = 0; i < ARRAY_SIZE(status); i++) {
+		regmap_read(cs35l41->regmap,
+			    CS35L41_IRQ1_STATUS1 + (i * CS35L41_REGSTRIDE),
+			    &status[i]);
+		regmap_read(cs35l41->regmap,
+			    CS35L41_IRQ1_MASK1 + (i * CS35L41_REGSTRIDE),
+			    &masks[i]);
+	}
+
+	/* Check to see if unmasked bits are active */
+	if (!(status[0] & ~masks[0]) && !(status[1] & ~masks[1]) &&
+	    !(status[2] & ~masks[2]) && !(status[3] & ~masks[3]))
+		goto done;
+
+	if (status[3] & CS35L41_OTP_BOOT_DONE) {
+		regmap_update_bits(cs35l41->regmap, CS35L41_IRQ1_MASK4,
+				   CS35L41_OTP_BOOT_DONE, CS35L41_OTP_BOOT_DONE);
+	}
+
+	/*
+	 * The following interrupts require a
+	 * protection release cycle to get the
+	 * speaker out of Safe-Mode.
+	 */
+	if (status[0] & CS35L41_AMP_SHORT_ERR) {
+		dev_crit_ratelimited(cs35l41->dev, "Amp short error\n");
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_AMP_SHORT_ERR);
+		regmap_write(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_AMP_SHORT_ERR_RLS,
+				   CS35L41_AMP_SHORT_ERR_RLS);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_AMP_SHORT_ERR_RLS, 0);
+		ret = IRQ_HANDLED;
+	}
+
+	if (status[0] & CS35L41_TEMP_WARN) {
+		dev_crit_ratelimited(cs35l41->dev, "Over temperature warning\n");
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_TEMP_WARN);
+		regmap_write(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_TEMP_WARN_ERR_RLS,
+				   CS35L41_TEMP_WARN_ERR_RLS);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_TEMP_WARN_ERR_RLS, 0);
+		ret = IRQ_HANDLED;
+	}
+
+	if (status[0] & CS35L41_TEMP_ERR) {
+		dev_crit_ratelimited(cs35l41->dev, "Over temperature error\n");
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_TEMP_ERR);
+		regmap_write(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_TEMP_ERR_RLS,
+				   CS35L41_TEMP_ERR_RLS);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_TEMP_ERR_RLS, 0);
+		ret = IRQ_HANDLED;
+	}
+
+	if (status[0] & CS35L41_BST_OVP_ERR) {
+		dev_crit_ratelimited(cs35l41->dev, "VBST Over Voltage error\n");
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL2,
+				   CS35L41_BST_EN_MASK, 0);
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_BST_OVP_ERR);
+		regmap_write(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_BST_OVP_ERR_RLS,
+				   CS35L41_BST_OVP_ERR_RLS);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_BST_OVP_ERR_RLS, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL2,
+				   CS35L41_BST_EN_MASK,
+				   CS35L41_BST_EN_DEFAULT << CS35L41_BST_EN_SHIFT);
+		ret = IRQ_HANDLED;
+	}
+
+	if (status[0] & CS35L41_BST_DCM_UVP_ERR) {
+		dev_crit_ratelimited(cs35l41->dev, "DCM VBST Under Voltage Error\n");
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL2,
+				   CS35L41_BST_EN_MASK, 0);
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_BST_DCM_UVP_ERR);
+		regmap_write(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_BST_UVP_ERR_RLS,
+				   CS35L41_BST_UVP_ERR_RLS);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_BST_UVP_ERR_RLS, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL2,
+				   CS35L41_BST_EN_MASK,
+				   CS35L41_BST_EN_DEFAULT << CS35L41_BST_EN_SHIFT);
+		ret = IRQ_HANDLED;
+	}
+
+	if (status[0] & CS35L41_BST_SHORT_ERR) {
+		dev_crit_ratelimited(cs35l41->dev, "LBST error: powering off!\n");
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL2,
+				   CS35L41_BST_EN_MASK, 0);
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_BST_SHORT_ERR);
+		regmap_write(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_BST_SHORT_ERR_RLS,
+				   CS35L41_BST_SHORT_ERR_RLS);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PROTECT_REL_ERR_IGN,
+				   CS35L41_BST_SHORT_ERR_RLS, 0);
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL2,
+				   CS35L41_BST_EN_MASK,
+				   CS35L41_BST_EN_DEFAULT << CS35L41_BST_EN_SHIFT);
+		ret = IRQ_HANDLED;
+	}
+
+done:
+	pm_runtime_mark_last_busy(cs35l41->dev);
+	pm_runtime_put_autosuspend(cs35l41->dev);
+
+	return ret;
+}
+
+static const struct reg_sequence cs35l41_pup_patch[] = {
+	{ CS35L41_TEST_KEY_CTL, 0x00000055 },
+	{ CS35L41_TEST_KEY_CTL, 0x000000AA },
+	{ 0x00002084, 0x002F1AA0 },
+	{ CS35L41_TEST_KEY_CTL, 0x000000CC },
+	{ CS35L41_TEST_KEY_CTL, 0x00000033 },
+};
+
+static const struct reg_sequence cs35l41_pdn_patch[] = {
+	{ CS35L41_TEST_KEY_CTL, 0x00000055 },
+	{ CS35L41_TEST_KEY_CTL, 0x000000AA },
+	{ 0x00002084, 0x002F1AA3 },
+	{ CS35L41_TEST_KEY_CTL, 0x000000CC },
+	{ CS35L41_TEST_KEY_CTL, 0x00000033 },
+};
+
+static int cs35l41_main_amp_event(struct snd_soc_dapm_widget *w,
+				  struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(component);
+	unsigned int val;
+	int ret = 0;
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMU:
+		regmap_multi_reg_write_bypassed(cs35l41->regmap,
+						cs35l41_pup_patch,
+						ARRAY_SIZE(cs35l41_pup_patch));
+
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL1,
+				   CS35L41_GLOBAL_EN_MASK,
+				   1 << CS35L41_GLOBAL_EN_SHIFT);
+
+		usleep_range(1000, 1100);
+		break;
+	case SND_SOC_DAPM_POST_PMD:
+		regmap_update_bits(cs35l41->regmap, CS35L41_PWR_CTRL1,
+				   CS35L41_GLOBAL_EN_MASK, 0);
+
+		ret = regmap_read_poll_timeout(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+					       val, val &  CS35L41_PDN_DONE_MASK,
+					       1000, 100000);
+		if (ret)
+			dev_warn(cs35l41->dev, "PDN failed: %d\n", ret);
+
+		regmap_write(cs35l41->regmap, CS35L41_IRQ1_STATUS1,
+			     CS35L41_PDN_DONE_MASK);
+
+		regmap_multi_reg_write_bypassed(cs35l41->regmap,
+						cs35l41_pdn_patch,
+						ARRAY_SIZE(cs35l41_pdn_patch));
+		break;
+	default:
+		dev_err(cs35l41->dev, "Invalid event = 0x%x\n", event);
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct snd_soc_dapm_widget cs35l41_dapm_widgets[] = {
+	SND_SOC_DAPM_SPK("DSP1 Preload", NULL),
+	SND_SOC_DAPM_SUPPLY_S("DSP1 Preloader", 100, SND_SOC_NOPM, 0, 0,
+			      cs35l41_dsp_preload_ev,
+			      SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
+	SND_SOC_DAPM_OUT_DRV_E("DSP1", SND_SOC_NOPM, 0, 0, NULL, 0,
+			       cs35l41_dsp_audio_ev,
+			       SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
+
+	SND_SOC_DAPM_OUTPUT("SPK"),
+
+	SND_SOC_DAPM_AIF_IN("ASPRX1", NULL, 0, CS35L41_SP_ENABLES, 16, 0),
+	SND_SOC_DAPM_AIF_IN("ASPRX2", NULL, 0, CS35L41_SP_ENABLES, 17, 0),
+	SND_SOC_DAPM_AIF_OUT("ASPTX1", NULL, 0, CS35L41_SP_ENABLES, 0, 0),
+	SND_SOC_DAPM_AIF_OUT("ASPTX2", NULL, 0, CS35L41_SP_ENABLES, 1, 0),
+	SND_SOC_DAPM_AIF_OUT("ASPTX3", NULL, 0, CS35L41_SP_ENABLES, 2, 0),
+	SND_SOC_DAPM_AIF_OUT("ASPTX4", NULL, 0, CS35L41_SP_ENABLES, 3, 0),
+
+	SND_SOC_DAPM_SIGGEN("VSENSE"),
+	SND_SOC_DAPM_SIGGEN("ISENSE"),
+	SND_SOC_DAPM_SIGGEN("VP"),
+	SND_SOC_DAPM_SIGGEN("VBST"),
+	SND_SOC_DAPM_SIGGEN("TEMP"),
+
+	SND_SOC_DAPM_SUPPLY("VMON", CS35L41_PWR_CTRL2, 12, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("IMON", CS35L41_PWR_CTRL2, 13, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("VPMON", CS35L41_PWR_CTRL2, 8, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("VBSTMON", CS35L41_PWR_CTRL2, 9, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("TEMPMON", CS35L41_PWR_CTRL2, 10, 0, NULL, 0),
+
+	SND_SOC_DAPM_ADC("VMON ADC", NULL, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_ADC("IMON ADC", NULL, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_ADC("VPMON ADC", NULL, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_ADC("VBSTMON ADC", NULL, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_ADC("TEMPMON ADC", NULL, SND_SOC_NOPM, 0, 0),
+
+	SND_SOC_DAPM_ADC("CLASS H", NULL, CS35L41_PWR_CTRL3, 4, 0),
+
+	SND_SOC_DAPM_OUT_DRV_E("Main AMP", CS35L41_PWR_CTRL2, 0, 0, NULL, 0,
+			       cs35l41_main_amp_event,
+			       SND_SOC_DAPM_POST_PMD |	SND_SOC_DAPM_POST_PMU),
+
+	SND_SOC_DAPM_MUX("ASP TX1 Source", SND_SOC_NOPM, 0, 0, &asp_tx1_mux),
+	SND_SOC_DAPM_MUX("ASP TX2 Source", SND_SOC_NOPM, 0, 0, &asp_tx2_mux),
+	SND_SOC_DAPM_MUX("ASP TX3 Source", SND_SOC_NOPM, 0, 0, &asp_tx3_mux),
+	SND_SOC_DAPM_MUX("ASP TX4 Source", SND_SOC_NOPM, 0, 0, &asp_tx4_mux),
+	SND_SOC_DAPM_MUX("DSP RX1 Source", SND_SOC_NOPM, 0, 0, &dsp_rx1_mux),
+	SND_SOC_DAPM_MUX("DSP RX2 Source", SND_SOC_NOPM, 0, 0, &dsp_rx2_mux),
+	SND_SOC_DAPM_MUX("PCM Source", SND_SOC_NOPM, 0, 0, &pcm_source_mux),
+	SND_SOC_DAPM_SWITCH("DRE", SND_SOC_NOPM, 0, 0, &dre_ctrl),
+};
+
+static const struct snd_soc_dapm_route cs35l41_audio_map[] = {
+	{"DSP RX1 Source", "ASPRX1", "ASPRX1"},
+	{"DSP RX1 Source", "ASPRX2", "ASPRX2"},
+	{"DSP RX2 Source", "ASPRX1", "ASPRX1"},
+	{"DSP RX2 Source", "ASPRX2", "ASPRX2"},
+
+	{"DSP1", NULL, "DSP RX1 Source"},
+	{"DSP1", NULL, "DSP RX2 Source"},
+
+	{"ASP TX1 Source", "VMON", "VMON ADC"},
+	{"ASP TX1 Source", "IMON", "IMON ADC"},
+	{"ASP TX1 Source", "VPMON", "VPMON ADC"},
+	{"ASP TX1 Source", "VBSTMON", "VBSTMON ADC"},
+	{"ASP TX1 Source", "DSPTX1", "DSP1"},
+	{"ASP TX1 Source", "DSPTX2", "DSP1"},
+	{"ASP TX1 Source", "ASPRX1", "ASPRX1" },
+	{"ASP TX1 Source", "ASPRX2", "ASPRX2" },
+	{"ASP TX2 Source", "VMON", "VMON ADC"},
+	{"ASP TX2 Source", "IMON", "IMON ADC"},
+	{"ASP TX2 Source", "VPMON", "VPMON ADC"},
+	{"ASP TX2 Source", "VBSTMON", "VBSTMON ADC"},
+	{"ASP TX2 Source", "DSPTX1", "DSP1"},
+	{"ASP TX2 Source", "DSPTX2", "DSP1"},
+	{"ASP TX2 Source", "ASPRX1", "ASPRX1" },
+	{"ASP TX2 Source", "ASPRX2", "ASPRX2" },
+	{"ASP TX3 Source", "VMON", "VMON ADC"},
+	{"ASP TX3 Source", "IMON", "IMON ADC"},
+	{"ASP TX3 Source", "VPMON", "VPMON ADC"},
+	{"ASP TX3 Source", "VBSTMON", "VBSTMON ADC"},
+	{"ASP TX3 Source", "DSPTX1", "DSP1"},
+	{"ASP TX3 Source", "DSPTX2", "DSP1"},
+	{"ASP TX3 Source", "ASPRX1", "ASPRX1" },
+	{"ASP TX3 Source", "ASPRX2", "ASPRX2" },
+	{"ASP TX4 Source", "VMON", "VMON ADC"},
+	{"ASP TX4 Source", "IMON", "IMON ADC"},
+	{"ASP TX4 Source", "VPMON", "VPMON ADC"},
+	{"ASP TX4 Source", "VBSTMON", "VBSTMON ADC"},
+	{"ASP TX4 Source", "DSPTX1", "DSP1"},
+	{"ASP TX4 Source", "DSPTX2", "DSP1"},
+	{"ASP TX4 Source", "ASPRX1", "ASPRX1" },
+	{"ASP TX4 Source", "ASPRX2", "ASPRX2" },
+	{"ASPTX1", NULL, "ASP TX1 Source"},
+	{"ASPTX2", NULL, "ASP TX2 Source"},
+	{"ASPTX3", NULL, "ASP TX3 Source"},
+	{"ASPTX4", NULL, "ASP TX4 Source"},
+	{"AMP Capture", NULL, "ASPTX1"},
+	{"AMP Capture", NULL, "ASPTX2"},
+	{"AMP Capture", NULL, "ASPTX3"},
+	{"AMP Capture", NULL, "ASPTX4"},
+
+	{"DSP1", NULL, "VMON"},
+	{"DSP1", NULL, "IMON"},
+	{"DSP1", NULL, "VPMON"},
+	{"DSP1", NULL, "VBSTMON"},
+	{"DSP1", NULL, "TEMPMON"},
+
+	{"VMON ADC", NULL, "VMON"},
+	{"IMON ADC", NULL, "IMON"},
+	{"VPMON ADC", NULL, "VPMON"},
+	{"VBSTMON ADC", NULL, "VBSTMON"},
+	{"TEMPMON ADC", NULL, "TEMPMON"},
+
+	{"VMON ADC", NULL, "VSENSE"},
+	{"IMON ADC", NULL, "ISENSE"},
+	{"VPMON ADC", NULL, "VP"},
+	{"VBSTMON ADC", NULL, "VBST"},
+	{"TEMPMON ADC", NULL, "TEMP"},
+
+	{"DSP1 Preload", NULL, "DSP1 Preloader"},
+	{"DSP1", NULL, "DSP1 Preloader"},
+
+	{"ASPRX1", NULL, "AMP Playback"},
+	{"ASPRX2", NULL, "AMP Playback"},
+	{"DRE", "Switch", "CLASS H"},
+	{"Main AMP", NULL, "CLASS H"},
+	{"Main AMP", NULL, "DRE"},
+	{"SPK", NULL, "Main AMP"},
+
+	{"PCM Source", "ASP", "ASPRX1"},
+	{"PCM Source", "DSP", "DSP1"},
+	{"CLASS H", NULL, "PCM Source"},
+};
+
+static const struct wm_adsp_region cs35l41_dsp1_regions[] = {
+	{ .type = WMFW_HALO_PM_PACKED,	.base = CS35L41_DSP1_PMEM_0 },
+	{ .type = WMFW_HALO_XM_PACKED,	.base = CS35L41_DSP1_XMEM_PACK_0 },
+	{ .type = WMFW_HALO_YM_PACKED,	.base = CS35L41_DSP1_YMEM_PACK_0 },
+	{. type = WMFW_ADSP2_XM,	.base = CS35L41_DSP1_XMEM_UNPACK24_0},
+	{. type = WMFW_ADSP2_YM,	.base = CS35L41_DSP1_YMEM_UNPACK24_0},
+};
+
+static int cs35l41_set_channel_map(struct snd_soc_dai *dai, unsigned int tx_n,
+				   unsigned int *tx_slot, unsigned int rx_n, unsigned int *rx_slot)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(dai->component);
+
+	return cs35l41_set_channels(cs35l41->dev, cs35l41->regmap, tx_n, tx_slot, rx_n, rx_slot);
+}
+
+static int cs35l41_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(dai->component);
+	unsigned int daifmt = 0;
+
+	switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
+	case SND_SOC_DAIFMT_CBP_CFP:
+		daifmt |= CS35L41_SCLK_MSTR_MASK | CS35L41_LRCLK_MSTR_MASK;
+		break;
+	case SND_SOC_DAIFMT_CBC_CFC:
+		break;
+	default:
+		dev_warn(cs35l41->dev, "Mixed provider/consumer mode unsupported\n");
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_DSP_A:
+		break;
+	case SND_SOC_DAIFMT_I2S:
+		daifmt |= 2 << CS35L41_ASP_FMT_SHIFT;
+		break;
+	default:
+		dev_warn(cs35l41->dev, "Invalid or unsupported DAI format\n");
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_IF:
+		daifmt |= CS35L41_LRCLK_INV_MASK;
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		daifmt |= CS35L41_SCLK_INV_MASK;
+		break;
+	case SND_SOC_DAIFMT_IB_IF:
+		daifmt |= CS35L41_LRCLK_INV_MASK | CS35L41_SCLK_INV_MASK;
+		break;
+	case SND_SOC_DAIFMT_NB_NF:
+		break;
+	default:
+		dev_warn(cs35l41->dev, "Invalid DAI clock INV\n");
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(cs35l41->regmap, CS35L41_SP_FORMAT,
+				  CS35L41_SCLK_MSTR_MASK | CS35L41_LRCLK_MSTR_MASK |
+				  CS35L41_ASP_FMT_MASK | CS35L41_LRCLK_INV_MASK |
+				  CS35L41_SCLK_INV_MASK, daifmt);
+}
+
+struct cs35l41_global_fs_config {
+	int rate;
+	int fs_cfg;
+};
+
+static const struct cs35l41_global_fs_config cs35l41_fs_rates[] = {
+	{ 12000,	0x01 },
+	{ 24000,	0x02 },
+	{ 48000,	0x03 },
+	{ 96000,	0x04 },
+	{ 192000,	0x05 },
+	{ 11025,	0x09 },
+	{ 22050,	0x0A },
+	{ 44100,	0x0B },
+	{ 88200,	0x0C },
+	{ 176400,	0x0D },
+	{ 8000,		0x11 },
+	{ 16000,	0x12 },
+	{ 32000,	0x13 },
+};
+
+static int cs35l41_pcm_hw_params(struct snd_pcm_substream *substream,
+				 struct snd_pcm_hw_params *params,
+				 struct snd_soc_dai *dai)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(dai->component);
+	unsigned int rate = params_rate(params);
+	u8 asp_wl;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cs35l41_fs_rates); i++) {
+		if (rate == cs35l41_fs_rates[i].rate)
+			break;
+	}
+
+	if (i >= ARRAY_SIZE(cs35l41_fs_rates)) {
+		dev_err(cs35l41->dev, "Unsupported rate: %u\n", rate);
+		return -EINVAL;
+	}
+
+	asp_wl = params_width(params);
+
+	if (i < ARRAY_SIZE(cs35l41_fs_rates))
+		regmap_update_bits(cs35l41->regmap, CS35L41_GLOBAL_CLK_CTRL,
+				   CS35L41_GLOBAL_FS_MASK,
+				   cs35l41_fs_rates[i].fs_cfg << CS35L41_GLOBAL_FS_SHIFT);
+
+	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
+		regmap_update_bits(cs35l41->regmap, CS35L41_SP_FORMAT,
+				   CS35L41_ASP_WIDTH_RX_MASK,
+				   asp_wl << CS35L41_ASP_WIDTH_RX_SHIFT);
+		regmap_update_bits(cs35l41->regmap, CS35L41_SP_RX_WL,
+				   CS35L41_ASP_RX_WL_MASK,
+				   asp_wl << CS35L41_ASP_RX_WL_SHIFT);
+	} else {
+		regmap_update_bits(cs35l41->regmap, CS35L41_SP_FORMAT,
+				   CS35L41_ASP_WIDTH_TX_MASK,
+				   asp_wl << CS35L41_ASP_WIDTH_TX_SHIFT);
+		regmap_update_bits(cs35l41->regmap, CS35L41_SP_TX_WL,
+				   CS35L41_ASP_TX_WL_MASK,
+				   asp_wl << CS35L41_ASP_TX_WL_SHIFT);
+	}
+
+	return 0;
+}
+
+static int cs35l41_get_clk_config(int freq)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cs35l41_pll_sysclk); i++) {
+		if (cs35l41_pll_sysclk[i].freq == freq)
+			return cs35l41_pll_sysclk[i].clk_cfg;
+	}
+
+	return -EINVAL;
+}
+
+static const unsigned int cs35l41_src_rates[] = {
+	8000, 12000, 11025, 16000, 22050, 24000, 32000,
+	44100, 48000, 88200, 96000, 176400, 192000
+};
+
+static const struct snd_pcm_hw_constraint_list cs35l41_constraints = {
+	.count = ARRAY_SIZE(cs35l41_src_rates),
+	.list = cs35l41_src_rates,
+};
+
+static int cs35l41_pcm_startup(struct snd_pcm_substream *substream,
+			       struct snd_soc_dai *dai)
+{
+	if (substream->runtime)
+		return snd_pcm_hw_constraint_list(substream->runtime, 0,
+						  SNDRV_PCM_HW_PARAM_RATE,
+						  &cs35l41_constraints);
+	return 0;
+}
+
+static int cs35l41_component_set_sysclk(struct snd_soc_component *component,
+					int clk_id, int source,
+					unsigned int freq, int dir)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(component);
+	int extclk_cfg, clksrc;
+
+	switch (clk_id) {
+	case CS35L41_CLKID_SCLK:
+		clksrc = CS35L41_PLLSRC_SCLK;
+		break;
+	case CS35L41_CLKID_LRCLK:
+		clksrc = CS35L41_PLLSRC_LRCLK;
+		break;
+	case CS35L41_CLKID_MCLK:
+		clksrc = CS35L41_PLLSRC_MCLK;
+		break;
+	default:
+		dev_err(cs35l41->dev, "Invalid CLK Config\n");
+		return -EINVAL;
+	}
+
+	extclk_cfg = cs35l41_get_clk_config(freq);
+
+	if (extclk_cfg < 0) {
+		dev_err(cs35l41->dev, "Invalid CLK Config: %d, freq: %u\n",
+			extclk_cfg, freq);
+		return -EINVAL;
+	}
+
+	regmap_update_bits(cs35l41->regmap, CS35L41_PLL_CLK_CTRL,
+			   CS35L41_PLL_OPENLOOP_MASK,
+			   1 << CS35L41_PLL_OPENLOOP_SHIFT);
+	regmap_update_bits(cs35l41->regmap, CS35L41_PLL_CLK_CTRL,
+			   CS35L41_REFCLK_FREQ_MASK,
+			   extclk_cfg << CS35L41_REFCLK_FREQ_SHIFT);
+	regmap_update_bits(cs35l41->regmap, CS35L41_PLL_CLK_CTRL,
+			   CS35L41_PLL_CLK_EN_MASK,
+			   0 << CS35L41_PLL_CLK_EN_SHIFT);
+	regmap_update_bits(cs35l41->regmap, CS35L41_PLL_CLK_CTRL,
+			   CS35L41_PLL_CLK_SEL_MASK, clksrc);
+	regmap_update_bits(cs35l41->regmap, CS35L41_PLL_CLK_CTRL,
+			   CS35L41_PLL_OPENLOOP_MASK,
+			   0 << CS35L41_PLL_OPENLOOP_SHIFT);
+	regmap_update_bits(cs35l41->regmap, CS35L41_PLL_CLK_CTRL,
+			   CS35L41_PLL_CLK_EN_MASK,
+			   1 << CS35L41_PLL_CLK_EN_SHIFT);
+
+	return 0;
+}
+
+static int cs35l41_dai_set_sysclk(struct snd_soc_dai *dai,
+				  int clk_id, unsigned int freq, int dir)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(dai->component);
+	unsigned int fs1_val;
+	unsigned int fs2_val;
+	unsigned int val;
+	int fsindex;
+
+	fsindex = cs35l41_get_fs_mon_config_index(freq);
+	if (fsindex < 0) {
+		dev_err(cs35l41->dev, "Invalid CLK Config freq: %u\n", freq);
+		return -EINVAL;
+	}
+
+	dev_dbg(cs35l41->dev, "Set DAI sysclk %d\n", freq);
+
+	if (freq <= 6144000) {
+		/* Use the lookup table */
+		fs1_val = cs35l41_fs_mon[fsindex].fs1;
+		fs2_val = cs35l41_fs_mon[fsindex].fs2;
+	} else {
+		/* Use hard-coded values */
+		fs1_val = 0x10;
+		fs2_val = 0x24;
+	}
+
+	val = fs1_val;
+	val |= (fs2_val << CS35L41_FS2_WINDOW_SHIFT) & CS35L41_FS2_WINDOW_MASK;
+	regmap_write(cs35l41->regmap, CS35L41_TST_FS_MON0, val);
+
+	return 0;
+}
+
+static int cs35l41_set_pdata(struct cs35l41_private *cs35l41)
+{
+	int ret;
+
+	/* Set Platform Data */
+	/* Required */
+	if (cs35l41->pdata.bst_ipk &&
+	    cs35l41->pdata.bst_ind && cs35l41->pdata.bst_cap) {
+		ret = cs35l41_boost_config(cs35l41->dev, cs35l41->regmap, cs35l41->pdata.bst_ind,
+					   cs35l41->pdata.bst_cap, cs35l41->pdata.bst_ipk);
+		if (ret) {
+			dev_err(cs35l41->dev, "Error in Boost DT config: %d\n", ret);
+			return ret;
+		}
+	} else {
+		dev_err(cs35l41->dev, "Incomplete Boost component DT config\n");
+		return -EINVAL;
+	}
+
+	/* Optional */
+	if (cs35l41->pdata.dout_hiz <= CS35L41_ASP_DOUT_HIZ_MASK &&
+	    cs35l41->pdata.dout_hiz >= 0)
+		regmap_update_bits(cs35l41->regmap, CS35L41_SP_HIZ_CTRL,
+				   CS35L41_ASP_DOUT_HIZ_MASK,
+				   cs35l41->pdata.dout_hiz);
+
+	return 0;
+}
+
+static int cs35l41_irq_gpio_config(struct cs35l41_private *cs35l41)
+{
+	struct cs35l41_irq_cfg *irq_gpio_cfg1 = &cs35l41->pdata.irq_config1;
+	struct cs35l41_irq_cfg *irq_gpio_cfg2 = &cs35l41->pdata.irq_config2;
+	int irq_pol = IRQF_TRIGGER_NONE;
+
+	regmap_update_bits(cs35l41->regmap, CS35L41_GPIO1_CTRL1,
+			   CS35L41_GPIO_POL_MASK | CS35L41_GPIO_DIR_MASK,
+			   irq_gpio_cfg1->irq_pol_inv << CS35L41_GPIO_POL_SHIFT |
+			   !irq_gpio_cfg1->irq_out_en << CS35L41_GPIO_DIR_SHIFT);
+
+	regmap_update_bits(cs35l41->regmap, CS35L41_GPIO2_CTRL1,
+			   CS35L41_GPIO_POL_MASK | CS35L41_GPIO_DIR_MASK,
+			   irq_gpio_cfg1->irq_pol_inv << CS35L41_GPIO_POL_SHIFT |
+			   !irq_gpio_cfg1->irq_out_en << CS35L41_GPIO_DIR_SHIFT);
+
+	regmap_update_bits(cs35l41->regmap, CS35L41_GPIO_PAD_CONTROL,
+			   CS35L41_GPIO1_CTRL_MASK | CS35L41_GPIO2_CTRL_MASK,
+			   irq_gpio_cfg1->irq_src_sel << CS35L41_GPIO1_CTRL_SHIFT |
+			   irq_gpio_cfg2->irq_src_sel << CS35L41_GPIO2_CTRL_SHIFT);
+
+	if ((irq_gpio_cfg2->irq_src_sel ==
+			(CS35L41_GPIO_CTRL_ACTV_LO | CS35L41_VALID_PDATA)) ||
+		(irq_gpio_cfg2->irq_src_sel ==
+			(CS35L41_GPIO_CTRL_OPEN_INT | CS35L41_VALID_PDATA)))
+		irq_pol = IRQF_TRIGGER_LOW;
+	else if (irq_gpio_cfg2->irq_src_sel ==
+			(CS35L41_GPIO_CTRL_ACTV_HI | CS35L41_VALID_PDATA))
+		irq_pol = IRQF_TRIGGER_HIGH;
+
+	return irq_pol;
+}
+
+static int cs35l41_component_probe(struct snd_soc_component *component)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(component);
+
+	return wm_adsp2_component_probe(&cs35l41->dsp, component);
+}
+
+static void cs35l41_component_remove(struct snd_soc_component *component)
+{
+	struct cs35l41_private *cs35l41 = snd_soc_component_get_drvdata(component);
+
+	wm_adsp2_component_remove(&cs35l41->dsp, component);
+}
+
+static const struct snd_soc_dai_ops cs35l41_ops = {
+	.startup = cs35l41_pcm_startup,
+	.set_fmt = cs35l41_set_dai_fmt,
+	.hw_params = cs35l41_pcm_hw_params,
+	.set_sysclk = cs35l41_dai_set_sysclk,
+	.set_channel_map = cs35l41_set_channel_map,
+};
+
+static struct snd_soc_dai_driver cs35l41_dai[] = {
+	{
+		.name = "cs35l41-pcm",
+		.id = 0,
+		.playback = {
+			.stream_name = "AMP Playback",
+			.channels_min = 1,
+			.channels_max = 2,
+			.rates = SNDRV_PCM_RATE_KNOT,
+			.formats = CS35L41_RX_FORMATS,
+		},
+		.capture = {
+			.stream_name = "AMP Capture",
+			.channels_min = 1,
+			.channels_max = 8,
+			.rates = SNDRV_PCM_RATE_KNOT,
+			.formats = CS35L41_TX_FORMATS,
+		},
+		.ops = &cs35l41_ops,
+		.symmetric_rate = 1,
+	},
+};
+
+static const struct snd_soc_component_driver soc_component_dev_cs35l41 = {
+	.name = "cs35l41-codec",
+	.probe = cs35l41_component_probe,
+	.remove = cs35l41_component_remove,
+
+	.dapm_widgets = cs35l41_dapm_widgets,
+	.num_dapm_widgets = ARRAY_SIZE(cs35l41_dapm_widgets),
+	.dapm_routes = cs35l41_audio_map,
+	.num_dapm_routes = ARRAY_SIZE(cs35l41_audio_map),
+
+	.controls = cs35l41_aud_controls,
+	.num_controls = ARRAY_SIZE(cs35l41_aud_controls),
+	.set_sysclk = cs35l41_component_set_sysclk,
+};
+
+static int cs35l41_handle_pdata(struct device *dev,
+				struct cs35l41_platform_data *pdata,
+				struct cs35l41_private *cs35l41)
+{
+	struct cs35l41_irq_cfg *irq_gpio1_config = &pdata->irq_config1;
+	struct cs35l41_irq_cfg *irq_gpio2_config = &pdata->irq_config2;
+	unsigned int val;
+	int ret;
+
+	ret = device_property_read_u32(dev, "cirrus,boost-peak-milliamp", &val);
+	if (ret >= 0)
+		pdata->bst_ipk = val;
+
+	ret = device_property_read_u32(dev, "cirrus,boost-ind-nanohenry", &val);
+	if (ret >= 0)
+		pdata->bst_ind = val;
+
+	ret = device_property_read_u32(dev, "cirrus,boost-cap-microfarad", &val);
+	if (ret >= 0)
+		pdata->bst_cap = val;
+
+	ret = device_property_read_u32(dev, "cirrus,asp-sdout-hiz", &val);
+	if (ret >= 0)
+		pdata->dout_hiz = val;
+	else
+		pdata->dout_hiz = -1;
+
+	/* GPIO1 Pin Config */
+	irq_gpio1_config->irq_pol_inv = device_property_read_bool(dev,
+					"cirrus,gpio1-polarity-invert");
+	irq_gpio1_config->irq_out_en = device_property_read_bool(dev,
+					"cirrus,gpio1-output-enable");
+	ret = device_property_read_u32(dev, "cirrus,gpio1-src-select",
+				       &val);
+	if (ret >= 0)
+		irq_gpio1_config->irq_src_sel = val | CS35L41_VALID_PDATA;
+
+	/* GPIO2 Pin Config */
+	irq_gpio2_config->irq_pol_inv = device_property_read_bool(dev,
+					"cirrus,gpio2-polarity-invert");
+	irq_gpio2_config->irq_out_en = device_property_read_bool(dev,
+					"cirrus,gpio2-output-enable");
+	ret = device_property_read_u32(dev, "cirrus,gpio2-src-select",
+				       &val);
+	if (ret >= 0)
+		irq_gpio2_config->irq_src_sel = val | CS35L41_VALID_PDATA;
+
+	return 0;
+}
+
+static const struct reg_sequence cs35l41_fs_errata_patch[] = {
+	{ CS35L41_DSP1_RX1_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX2_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX3_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX4_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX5_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX6_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX7_RATE,	0x00000001 },
+	{ CS35L41_DSP1_RX8_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX1_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX2_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX3_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX4_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX5_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX6_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX7_RATE,	0x00000001 },
+	{ CS35L41_DSP1_TX8_RATE,	0x00000001 },
+};
+
+static int cs35l41_dsp_init(struct cs35l41_private *cs35l41)
+{
+	struct wm_adsp *dsp;
+	int ret;
+
+	dsp = &cs35l41->dsp;
+	dsp->part = "cs35l41";
+	dsp->num = 1;
+	dsp->type = WMFW_HALO;
+	dsp->rev = 0;
+	dsp->fw = 9; /* 9 is WM_ADSP_FW_SPK_PROT in wm_adsp.c */
+	dsp->dev = cs35l41->dev;
+	dsp->regmap = cs35l41->regmap;
+	dsp->base = CS35L41_DSP1_CTRL_BASE;
+	dsp->base_sysinfo = CS35L41_DSP1_SYS_ID;
+	dsp->mem = cs35l41_dsp1_regions;
+	dsp->num_mems = ARRAY_SIZE(cs35l41_dsp1_regions);
+	dsp->lock_regions = 0xFFFFFFFF;
+
+	ret = regmap_multi_reg_write(cs35l41->regmap, cs35l41_fs_errata_patch,
+				     ARRAY_SIZE(cs35l41_fs_errata_patch));
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Failed to write fs errata: %d\n", ret);
+		return ret;
+	}
+
+	ret = wm_halo_init(dsp);
+	if (ret) {
+		dev_err(cs35l41->dev, "wm_halo_init failed: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_write(cs35l41->regmap, CS35L41_DSP1_RX5_SRC,
+			   CS35L41_INPUT_SRC_VPMON);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Write INPUT_SRC_VPMON failed: %d\n", ret);
+		goto err_dsp;
+	}
+	ret = regmap_write(cs35l41->regmap, CS35L41_DSP1_RX6_SRC,
+			   CS35L41_INPUT_SRC_CLASSH);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Write INPUT_SRC_CLASSH failed: %d\n", ret);
+		goto err_dsp;
+	}
+	ret = regmap_write(cs35l41->regmap, CS35L41_DSP1_RX7_SRC,
+			   CS35L41_INPUT_SRC_TEMPMON);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Write INPUT_SRC_TEMPMON failed: %d\n", ret);
+		goto err_dsp;
+	}
+	ret = regmap_write(cs35l41->regmap, CS35L41_DSP1_RX8_SRC,
+			   CS35L41_INPUT_SRC_RSVD);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Write INPUT_SRC_RSVD failed: %d\n", ret);
+		goto err_dsp;
+	}
+
+	return 0;
+
+err_dsp:
+	wm_adsp2_remove(dsp);
+
+	return ret;
+}
+
+int cs35l41_probe(struct cs35l41_private *cs35l41,
+		  struct cs35l41_platform_data *pdata)
+{
+	u32 regid, reg_revid, i, mtl_revid, int_status, chipid_match;
+	int irq_pol = 0;
+	int ret;
+
+	if (pdata) {
+		cs35l41->pdata = *pdata;
+	} else {
+		ret = cs35l41_handle_pdata(cs35l41->dev, &cs35l41->pdata, cs35l41);
+		if (ret != 0)
+			return ret;
+	}
+
+	for (i = 0; i < CS35L41_NUM_SUPPLIES; i++)
+		cs35l41->supplies[i].supply = cs35l41_supplies[i];
+
+	ret = devm_regulator_bulk_get(cs35l41->dev, CS35L41_NUM_SUPPLIES,
+				      cs35l41->supplies);
+	if (ret != 0) {
+		dev_err(cs35l41->dev, "Failed to request core supplies: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_enable(CS35L41_NUM_SUPPLIES, cs35l41->supplies);
+	if (ret != 0) {
+		dev_err(cs35l41->dev, "Failed to enable core supplies: %d\n", ret);
+		return ret;
+	}
+
+	/* returning NULL can be an option if in stereo mode */
+	cs35l41->reset_gpio = devm_gpiod_get_optional(cs35l41->dev, "reset",
+						      GPIOD_OUT_LOW);
+	if (IS_ERR(cs35l41->reset_gpio)) {
+		ret = PTR_ERR(cs35l41->reset_gpio);
+		cs35l41->reset_gpio = NULL;
+		if (ret == -EBUSY) {
+			dev_info(cs35l41->dev,
+				 "Reset line busy, assuming shared reset\n");
+		} else {
+			dev_err(cs35l41->dev,
+				"Failed to get reset GPIO: %d\n", ret);
+			goto err;
+		}
+	}
+	if (cs35l41->reset_gpio) {
+		/* satisfy minimum reset pulse width spec */
+		usleep_range(2000, 2100);
+		gpiod_set_value_cansleep(cs35l41->reset_gpio, 1);
+	}
+
+	usleep_range(2000, 2100);
+
+	ret = regmap_read_poll_timeout(cs35l41->regmap, CS35L41_IRQ1_STATUS4,
+				       int_status, int_status & CS35L41_OTP_BOOT_DONE,
+				       1000, 100000);
+	if (ret) {
+		dev_err(cs35l41->dev,
+			"Failed waiting for OTP_BOOT_DONE: %d\n", ret);
+		goto err;
+	}
+
+	regmap_read(cs35l41->regmap, CS35L41_IRQ1_STATUS3, &int_status);
+	if (int_status & CS35L41_OTP_BOOT_ERR) {
+		dev_err(cs35l41->dev, "OTP Boot error\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	ret = regmap_read(cs35l41->regmap, CS35L41_DEVID, &regid);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Get Device ID failed: %d\n", ret);
+		goto err;
+	}
+
+	ret = regmap_read(cs35l41->regmap, CS35L41_REVID, &reg_revid);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Get Revision ID failed: %d\n", ret);
+		goto err;
+	}
+
+	mtl_revid = reg_revid & CS35L41_MTLREVID_MASK;
+
+	/* CS35L41 will have even MTLREVID
+	 * CS35L41R will have odd MTLREVID
+	 */
+	chipid_match = (mtl_revid % 2) ? CS35L41R_CHIP_ID : CS35L41_CHIP_ID;
+	if (regid != chipid_match) {
+		dev_err(cs35l41->dev, "CS35L41 Device ID (%X). Expected ID %X\n",
+			regid, chipid_match);
+		ret = -ENODEV;
+		goto err;
+	}
+
+	cs35l41_test_key_unlock(cs35l41->dev, cs35l41->regmap);
+
+	ret = cs35l41_register_errata_patch(cs35l41->dev, cs35l41->regmap, reg_revid);
+	if (ret)
+		goto err;
+
+	ret = cs35l41_otp_unpack(cs35l41->dev, cs35l41->regmap);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "OTP Unpack failed: %d\n", ret);
+		goto err;
+	}
+
+	cs35l41_test_key_lock(cs35l41->dev, cs35l41->regmap);
+
+	irq_pol = cs35l41_irq_gpio_config(cs35l41);
+
+	/* Set interrupt masks for critical errors */
+	regmap_write(cs35l41->regmap, CS35L41_IRQ1_MASK1,
+		     CS35L41_INT1_MASK_DEFAULT);
+
+	ret = devm_request_threaded_irq(cs35l41->dev, cs35l41->irq, NULL, cs35l41_irq,
+					IRQF_ONESHOT | IRQF_SHARED | irq_pol,
+					"cs35l41", cs35l41);
+	if (ret != 0) {
+		dev_err(cs35l41->dev, "Failed to request IRQ: %d\n", ret);
+		goto err;
+	}
+
+	ret = cs35l41_set_pdata(cs35l41);
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Set pdata failed: %d\n", ret);
+		goto err;
+	}
+
+	ret = cs35l41_dsp_init(cs35l41);
+	if (ret < 0)
+		goto err;
+
+	pm_runtime_set_autosuspend_delay(cs35l41->dev, 3000);
+	pm_runtime_use_autosuspend(cs35l41->dev);
+	pm_runtime_mark_last_busy(cs35l41->dev);
+	pm_runtime_set_active(cs35l41->dev);
+	pm_runtime_get_noresume(cs35l41->dev);
+	pm_runtime_enable(cs35l41->dev);
+
+	ret = devm_snd_soc_register_component(cs35l41->dev,
+					      &soc_component_dev_cs35l41,
+					      cs35l41_dai, ARRAY_SIZE(cs35l41_dai));
+	if (ret < 0) {
+		dev_err(cs35l41->dev, "Register codec failed: %d\n", ret);
+		goto err_pm;
+	}
+
+	pm_runtime_put_autosuspend(cs35l41->dev);
+
+	dev_info(cs35l41->dev, "Cirrus Logic CS35L41 (%x), Revision: %02X\n",
+		 regid, reg_revid);
+
+	return 0;
+
+err_pm:
+	pm_runtime_disable(cs35l41->dev);
+	pm_runtime_put_noidle(cs35l41->dev);
+
+	wm_adsp2_remove(&cs35l41->dsp);
+err:
+	regulator_bulk_disable(CS35L41_NUM_SUPPLIES, cs35l41->supplies);
+	gpiod_set_value_cansleep(cs35l41->reset_gpio, 0);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(cs35l41_probe);
+
+void cs35l41_remove(struct cs35l41_private *cs35l41)
+{
+	pm_runtime_get_sync(cs35l41->dev);
+	pm_runtime_disable(cs35l41->dev);
+
+	regmap_write(cs35l41->regmap, CS35L41_IRQ1_MASK1, 0xFFFFFFFF);
+	wm_adsp2_remove(&cs35l41->dsp);
+
+	pm_runtime_put_noidle(cs35l41->dev);
+
+	regulator_bulk_disable(CS35L41_NUM_SUPPLIES, cs35l41->supplies);
+	gpiod_set_value_cansleep(cs35l41->reset_gpio, 0);
+}
+EXPORT_SYMBOL_GPL(cs35l41_remove);
+
+static int __maybe_unused cs35l41_runtime_suspend(struct device *dev)
+{
+	struct cs35l41_private *cs35l41 = dev_get_drvdata(dev);
+
+	dev_dbg(cs35l41->dev, "Runtime suspend\n");
+
+	if (!cs35l41->dsp.preloaded || !cs35l41->dsp.running)
+		return 0;
+
+	dev_dbg(cs35l41->dev, "Enter hibernate\n");
+
+	regmap_write(cs35l41->regmap, CS35L41_WAKESRC_CTL, 0x0088);
+	regmap_write(cs35l41->regmap, CS35L41_WAKESRC_CTL, 0x0188);
+
+	// Don't wait for ACK since bus activity would wake the device
+	regmap_write(cs35l41->regmap, CS35L41_DSP_VIRT1_MBOX_1,
+		     CSPL_MBOX_CMD_HIBERNATE);
+
+	regcache_cache_only(cs35l41->regmap, true);
+	regcache_mark_dirty(cs35l41->regmap);
+
+	return 0;
+}
+
+static void cs35l41_wait_for_pwrmgt_sts(struct cs35l41_private *cs35l41)
+{
+	const int pwrmgt_retries = 10;
+	unsigned int sts;
+	int i, ret;
+
+	for (i = 0; i < pwrmgt_retries; i++) {
+		ret = regmap_read(cs35l41->regmap, CS35L41_PWRMGT_STS, &sts);
+		if (ret)
+			dev_err(cs35l41->dev, "Failed to read PWRMGT_STS: %d\n", ret);
+		else if (!(sts & CS35L41_WR_PEND_STS_MASK))
+			return;
+
+		udelay(20);
+	}
+
+	dev_err(cs35l41->dev, "Timed out reading PWRMGT_STS\n");
+}
+
+static int cs35l41_exit_hibernate(struct cs35l41_private *cs35l41)
+{
+	const int wake_retries = 20;
+	const int sleep_retries = 5;
+	int ret, i, j;
+
+	for (i = 0; i < sleep_retries; i++) {
+		dev_dbg(cs35l41->dev, "Exit hibernate\n");
+
+		for (j = 0; j < wake_retries; j++) {
+			ret = cs35l41_set_cspl_mbox_cmd(cs35l41,
+							CSPL_MBOX_CMD_OUT_OF_HIBERNATE);
+			if (!ret)
+				break;
+
+			usleep_range(100, 200);
+		}
+
+		if (j < wake_retries) {
+			dev_dbg(cs35l41->dev, "Wake success at cycle: %d\n", j);
+			return 0;
+		}
+
+		dev_err(cs35l41->dev, "Wake failed, re-enter hibernate: %d\n", ret);
+
+		cs35l41_wait_for_pwrmgt_sts(cs35l41);
+		regmap_write(cs35l41->regmap, CS35L41_WAKESRC_CTL, 0x0088);
+
+		cs35l41_wait_for_pwrmgt_sts(cs35l41);
+		regmap_write(cs35l41->regmap, CS35L41_WAKESRC_CTL, 0x0188);
+
+		cs35l41_wait_for_pwrmgt_sts(cs35l41);
+		regmap_write(cs35l41->regmap, CS35L41_PWRMGT_CTL, 0x3);
+	}
+
+	dev_err(cs35l41->dev, "Timed out waking device\n");
+
+	return -ETIMEDOUT;
+}
+
+static int __maybe_unused cs35l41_runtime_resume(struct device *dev)
+{
+	struct cs35l41_private *cs35l41 = dev_get_drvdata(dev);
+	int ret;
+
+	dev_dbg(cs35l41->dev, "Runtime resume\n");
+
+	if (!cs35l41->dsp.preloaded || !cs35l41->dsp.running)
+		return 0;
+
+	regcache_cache_only(cs35l41->regmap, false);
+
+	ret = cs35l41_exit_hibernate(cs35l41);
+	if (ret)
+		return ret;
+
+	/* Test key needs to be unlocked to allow the OTP settings to re-apply */
+	cs35l41_test_key_unlock(cs35l41->dev, cs35l41->regmap);
+	ret = regcache_sync(cs35l41->regmap);
+	cs35l41_test_key_lock(cs35l41->dev, cs35l41->regmap);
+	if (ret) {
+		dev_err(cs35l41->dev, "Failed to restore register cache: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int __maybe_unused cs35l41_sys_suspend(struct device *dev)
+{
+	struct cs35l41_private *cs35l41 = dev_get_drvdata(dev);
+
+	dev_dbg(cs35l41->dev, "System suspend, disabling IRQ\n");
+	disable_irq(cs35l41->irq);
+
+	return 0;
+}
+
+static int __maybe_unused cs35l41_sys_suspend_noirq(struct device *dev)
+{
+	struct cs35l41_private *cs35l41 = dev_get_drvdata(dev);
+
+	dev_dbg(cs35l41->dev, "Late system suspend, reenabling IRQ\n");
+	enable_irq(cs35l41->irq);
+
+	return 0;
+}
+
+static int __maybe_unused cs35l41_sys_resume_noirq(struct device *dev)
+{
+	struct cs35l41_private *cs35l41 = dev_get_drvdata(dev);
+
+	dev_dbg(cs35l41->dev, "Early system resume, disabling IRQ\n");
+	disable_irq(cs35l41->irq);
+
+	return 0;
+}
+
+static int __maybe_unused cs35l41_sys_resume(struct device *dev)
+{
+	struct cs35l41_private *cs35l41 = dev_get_drvdata(dev);
+
+	dev_dbg(cs35l41->dev, "System resume, reenabling IRQ\n");
+	enable_irq(cs35l41->irq);
+
+	return 0;
+}
+
+const struct dev_pm_ops cs35l41_pm_ops = {
+	SET_RUNTIME_PM_OPS(cs35l41_runtime_suspend, cs35l41_runtime_resume, NULL)
+
+	SET_SYSTEM_SLEEP_PM_OPS(cs35l41_sys_suspend, cs35l41_sys_resume)
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(cs35l41_sys_suspend_noirq, cs35l41_sys_resume_noirq)
+};
+EXPORT_SYMBOL_GPL(cs35l41_pm_ops);
+
+MODULE_DESCRIPTION("ASoC CS35L41 driver");
+MODULE_AUTHOR("David Rhodes, Cirrus Logic Inc, <david.rhodes@cirrus.com>");
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs35l41.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs35l41.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * cs35l41.h -- CS35L41 ALSA SoC audio driver
+ *
+ * Copyright 2017-2021 Cirrus Logic, Inc.
+ *
+ * Author: David Rhodes <david.rhodes@cirrus.com>
+ */
+
+#ifndef __CS35L41_H__
+#define __CS35L41_H__
+
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <linux/firmware.h>
+#include <sound/core.h>
+#include <sound/cs35l41.h>
+
+#include "wm_adsp.h"
+
+#define CS35L41_RX_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE)
+#define CS35L41_TX_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE)
+
+extern const struct dev_pm_ops cs35l41_pm_ops;
+
+enum cs35l41_cspl_mbox_status {
+	CSPL_MBOX_STS_RUNNING = 0,
+	CSPL_MBOX_STS_PAUSED = 1,
+	CSPL_MBOX_STS_RDY_FOR_REINIT = 2,
+};
+
+enum cs35l41_cspl_mbox_cmd {
+	CSPL_MBOX_CMD_NONE = 0,
+	CSPL_MBOX_CMD_PAUSE = 1,
+	CSPL_MBOX_CMD_RESUME = 2,
+	CSPL_MBOX_CMD_REINIT = 3,
+	CSPL_MBOX_CMD_STOP_PRE_REINIT = 4,
+	CSPL_MBOX_CMD_HIBERNATE = 5,
+	CSPL_MBOX_CMD_OUT_OF_HIBERNATE = 6,
+	CSPL_MBOX_CMD_UNKNOWN_CMD = -1,
+	CSPL_MBOX_CMD_INVALID_SEQUENCE = -2,
+};
+
+struct cs35l41_private {
+	struct wm_adsp dsp; /* needs to be first member */
+	struct snd_soc_codec *codec;
+	struct cs35l41_platform_data pdata;
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator_bulk_data supplies[CS35L41_NUM_SUPPLIES];
+	int irq;
+	/* GPIO for /RST */
+	struct gpio_desc *reset_gpio;
+};
+
+int cs35l41_probe(struct cs35l41_private *cs35l41,
+		  struct cs35l41_platform_data *pdata);
+void cs35l41_remove(struct cs35l41_private *cs35l41);
+
+#endif /*__CS35L41_H__*/
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs4265.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs4265.c
@@ -150,7 +150,6 @@
 	SOC_SINGLE("E to F Buffer Disable Switch", CS4265_SPDIF_CTL1,
 				6, 1, 0),
 	SOC_ENUM("C Data Access", cam_mode_enum),
-	SOC_SINGLE("SPDIF Switch", CS4265_SPDIF_CTL2, 5, 1, 1),
 	SOC_SINGLE("Validity Bit Control Switch", CS4265_SPDIF_CTL2,
 				3, 1, 0),
 	SOC_ENUM("SPDIF Mono/Stereo", spdif_mono_stereo_enum),
@@ -186,7 +185,7 @@
 
 	SND_SOC_DAPM_SWITCH("Loopback", SND_SOC_NOPM, 0, 0,
 			&loopback_ctl),
-	SND_SOC_DAPM_SWITCH("SPDIF", SND_SOC_NOPM, 0, 0,
+	SND_SOC_DAPM_SWITCH("SPDIF", CS4265_SPDIF_CTL2, 5, 1,
 			&spdif_switch),
 	SND_SOC_DAPM_SWITCH("DAC", CS4265_PWRCTL, 1, 1,
 			&dac_switch),
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l42.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l42.c
@@ -93,7 +93,7 @@
 	{ CS42L42_ASP_RX_INT_MASK,		0x1F },
 	{ CS42L42_ASP_TX_INT_MASK,		0x0F },
 	{ CS42L42_CODEC_INT_MASK,		0x03 },
-	{ CS42L42_SRCPL_INT_MASK,		0xFF },
+	{ CS42L42_SRCPL_INT_MASK,		0x7F },
 	{ CS42L42_VPMON_INT_MASK,		0x01 },
 	{ CS42L42_PLL_LOCK_INT_MASK,		0x01 },
 	{ CS42L42_TSRS_PLUG_INT_MASK,		0x0F },
@@ -130,7 +130,7 @@
 	{ CS42L42_MIXER_CHA_VOL,		0x3F },
 	{ CS42L42_MIXER_ADC_VOL,		0x3F },
 	{ CS42L42_MIXER_CHB_VOL,		0x3F },
-	{ CS42L42_EQ_COEF_IN0,			0x22 },
+	{ CS42L42_EQ_COEF_IN0,			0x00 },
 	{ CS42L42_EQ_COEF_IN1,			0x00 },
 	{ CS42L42_EQ_COEF_IN2,			0x00 },
 	{ CS42L42_EQ_COEF_IN3,			0x00 },
@@ -853,11 +853,10 @@
 
 	switch(substream->stream) {
 	case SNDRV_PCM_STREAM_CAPTURE:
-		if (channels == 2) {
-			val |= CS42L42_ASP_TX_CH2_AP_MASK;
-			val |= width << CS42L42_ASP_TX_CH2_RES_SHIFT;
-		}
-		val |= width << CS42L42_ASP_TX_CH1_RES_SHIFT;
+		/* channel 2 on high LRCLK */
+		val = CS42L42_ASP_TX_CH2_AP_MASK |
+		      (width << CS42L42_ASP_TX_CH2_RES_SHIFT) |
+		      (width << CS42L42_ASP_TX_CH1_RES_SHIFT);
 
 		snd_soc_component_update_bits(component, CS42L42_ASP_TX_CH_AP_RES,
 				CS42L42_ASP_TX_CH1_AP_MASK | CS42L42_ASP_TX_CH2_AP_MASK |
@@ -1685,12 +1684,15 @@
 			(1 << CS42L42_HS_CLAMP_DISABLE_SHIFT));
 
 	/* Enable the tip sense circuit */
+	regmap_update_bits(cs42l42->regmap, CS42L42_TSENSE_CTL,
+			   CS42L42_TS_INV_MASK, CS42L42_TS_INV_MASK);
+
 	regmap_update_bits(cs42l42->regmap, CS42L42_TIPSENSE_CTL,
 			CS42L42_TIP_SENSE_CTRL_MASK |
 			CS42L42_TIP_SENSE_INV_MASK |
 			CS42L42_TIP_SENSE_DEBOUNCE_MASK,
 			(3 << CS42L42_TIP_SENSE_CTRL_SHIFT) |
-			(0 << CS42L42_TIP_SENSE_INV_SHIFT) |
+			(!cs42l42->ts_inv << CS42L42_TIP_SENSE_INV_SHIFT) |
 			(2 << CS42L42_TIP_SENSE_DEBOUNCE_SHIFT));
 
 	/* Save the initial status of the tip sense */
@@ -1734,10 +1736,6 @@
 		cs42l42->ts_inv = CS42L42_TS_INV_DIS;
 	}
 
-	regmap_update_bits(cs42l42->regmap, CS42L42_TSENSE_CTL,
-			CS42L42_TS_INV_MASK,
-			(cs42l42->ts_inv << CS42L42_TS_INV_SHIFT));
-
 	ret = device_property_read_u32(dev, "cirrus,ts-dbnc-rise", &val);
 	if (!ret) {
 		switch (val) {
@@ -1948,8 +1946,9 @@
 			NULL, cs42l42_irq_thread,
 			IRQF_ONESHOT | IRQF_TRIGGER_LOW,
 			"cs42l42", cs42l42);
-
-	if (ret != 0)
+	if (ret == -EPROBE_DEFER)
+		goto err_disable;
+	else if (ret != 0)
 		dev_err(&i2c_client->dev,
 			"Failed to request IRQ: %d\n", ret);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l42.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l42.h
@@ -2,7 +2,7 @@
 /*
  * cs42l42.h -- CS42L42 ALSA SoC audio driver header
  *
- * Copyright 2016 Cirrus Logic, Inc.
+ * Copyright 2016-2022 Cirrus Logic, Inc.
  *
  * Author: James Schulman <james.schulman@cirrus.com>
  * Author: Brian Austin <brian.austin@cirrus.com>
@@ -13,754 +13,7 @@
 #define __CS42L42_H__
 
 #include <sound/jack.h>
-
-#define CS42L42_PAGE_REGISTER	0x00	/* Page Select Register */
-#define CS42L42_WIN_START	0x00
-#define CS42L42_WIN_LEN		0x100
-#define CS42L42_RANGE_MIN	0x00
-#define CS42L42_RANGE_MAX	0x7F
-
-#define CS42L42_PAGE_10		0x1000
-#define CS42L42_PAGE_11		0x1100
-#define CS42L42_PAGE_12		0x1200
-#define CS42L42_PAGE_13		0x1300
-#define CS42L42_PAGE_15		0x1500
-#define CS42L42_PAGE_19		0x1900
-#define CS42L42_PAGE_1B		0x1B00
-#define CS42L42_PAGE_1C		0x1C00
-#define CS42L42_PAGE_1D		0x1D00
-#define CS42L42_PAGE_1F		0x1F00
-#define CS42L42_PAGE_20		0x2000
-#define CS42L42_PAGE_21		0x2100
-#define CS42L42_PAGE_23		0x2300
-#define CS42L42_PAGE_24		0x2400
-#define CS42L42_PAGE_25		0x2500
-#define CS42L42_PAGE_26		0x2600
-#define CS42L42_PAGE_28		0x2800
-#define CS42L42_PAGE_29		0x2900
-#define CS42L42_PAGE_2A		0x2A00
-#define CS42L42_PAGE_30		0x3000
-
-#define CS42L42_CHIP_ID		0x42A42
-
-/* Page 0x10 Global Registers */
-#define CS42L42_DEVID_AB		(CS42L42_PAGE_10 + 0x01)
-#define CS42L42_DEVID_CD		(CS42L42_PAGE_10 + 0x02)
-#define CS42L42_DEVID_E			(CS42L42_PAGE_10 + 0x03)
-#define CS42L42_FABID			(CS42L42_PAGE_10 + 0x04)
-#define CS42L42_REVID			(CS42L42_PAGE_10 + 0x05)
-#define CS42L42_FRZ_CTL			(CS42L42_PAGE_10 + 0x06)
-
-#define CS42L42_SRC_CTL			(CS42L42_PAGE_10 + 0x07)
-#define CS42L42_SRC_BYPASS_DAC_SHIFT	1
-#define CS42L42_SRC_BYPASS_DAC_MASK	(1 << CS42L42_SRC_BYPASS_DAC_SHIFT)
-
-#define CS42L42_MCLK_STATUS		(CS42L42_PAGE_10 + 0x08)
-
-#define CS42L42_MCLK_CTL		(CS42L42_PAGE_10 + 0x09)
-#define CS42L42_INTERNAL_FS_SHIFT	1
-#define CS42L42_INTERNAL_FS_MASK	(1 << CS42L42_INTERNAL_FS_SHIFT)
-
-#define CS42L42_SFTRAMP_RATE		(CS42L42_PAGE_10 + 0x0A)
-#define CS42L42_I2C_DEBOUNCE		(CS42L42_PAGE_10 + 0x0E)
-#define CS42L42_I2C_STRETCH		(CS42L42_PAGE_10 + 0x0F)
-#define CS42L42_I2C_TIMEOUT		(CS42L42_PAGE_10 + 0x10)
-
-/* Page 0x11 Power and Headset Detect Registers */
-#define CS42L42_PWR_CTL1		(CS42L42_PAGE_11 + 0x01)
-#define CS42L42_ASP_DAO_PDN_SHIFT	7
-#define CS42L42_ASP_DAO_PDN_MASK	(1 << CS42L42_ASP_DAO_PDN_SHIFT)
-#define CS42L42_ASP_DAI_PDN_SHIFT	6
-#define CS42L42_ASP_DAI_PDN_MASK	(1 << CS42L42_ASP_DAI_PDN_SHIFT)
-#define CS42L42_MIXER_PDN_SHIFT		5
-#define CS42L42_MIXER_PDN_MASK		(1 << CS42L42_MIXER_PDN_SHIFT)
-#define CS42L42_EQ_PDN_SHIFT		4
-#define CS42L42_EQ_PDN_MASK		(1 << CS42L42_EQ_PDN_SHIFT)
-#define CS42L42_HP_PDN_SHIFT		3
-#define CS42L42_HP_PDN_MASK		(1 << CS42L42_HP_PDN_SHIFT)
-#define CS42L42_ADC_PDN_SHIFT		2
-#define CS42L42_ADC_PDN_MASK		(1 << CS42L42_ADC_PDN_SHIFT)
-#define CS42L42_PDN_ALL_SHIFT		0
-#define CS42L42_PDN_ALL_MASK		(1 << CS42L42_PDN_ALL_SHIFT)
-
-#define CS42L42_PWR_CTL2		(CS42L42_PAGE_11 + 0x02)
-#define CS42L42_ADC_SRC_PDNB_SHIFT	0
-#define CS42L42_ADC_SRC_PDNB_MASK	(1 << CS42L42_ADC_SRC_PDNB_SHIFT)
-#define CS42L42_DAC_SRC_PDNB_SHIFT	1
-#define CS42L42_DAC_SRC_PDNB_MASK	(1 << CS42L42_DAC_SRC_PDNB_SHIFT)
-#define CS42L42_ASP_DAI1_PDN_SHIFT	2
-#define CS42L42_ASP_DAI1_PDN_MASK	(1 << CS42L42_ASP_DAI1_PDN_SHIFT)
-#define CS42L42_SRC_PDN_OVERRIDE_SHIFT	3
-#define CS42L42_SRC_PDN_OVERRIDE_MASK	(1 << CS42L42_SRC_PDN_OVERRIDE_SHIFT)
-#define CS42L42_DISCHARGE_FILT_SHIFT	4
-#define CS42L42_DISCHARGE_FILT_MASK	(1 << CS42L42_DISCHARGE_FILT_SHIFT)
-
-#define CS42L42_PWR_CTL3			(CS42L42_PAGE_11 + 0x03)
-#define CS42L42_RING_SENSE_PDNB_SHIFT		1
-#define CS42L42_RING_SENSE_PDNB_MASK		(1 << \
-					CS42L42_RING_SENSE_PDNB_SHIFT)
-#define CS42L42_VPMON_PDNB_SHIFT		2
-#define CS42L42_VPMON_PDNB_MASK			(1 << \
-					CS42L42_VPMON_PDNB_SHIFT)
-#define CS42L42_SW_CLK_STP_STAT_SEL_SHIFT	5
-#define CS42L42_SW_CLK_STP_STAT_SEL_MASK	(3 << \
-					CS42L42_SW_CLK_STP_STAT_SEL_SHIFT)
-
-#define CS42L42_RSENSE_CTL1			(CS42L42_PAGE_11 + 0x04)
-#define CS42L42_RS_TRIM_R_SHIFT			0
-#define CS42L42_RS_TRIM_R_MASK			(1 << \
-					CS42L42_RS_TRIM_R_SHIFT)
-#define CS42L42_RS_TRIM_T_SHIFT			1
-#define CS42L42_RS_TRIM_T_MASK			(1 << \
-					CS42L42_RS_TRIM_T_SHIFT)
-#define CS42L42_HPREF_RS_SHIFT			2
-#define CS42L42_HPREF_RS_MASK			(1 << \
-					CS42L42_HPREF_RS_SHIFT)
-#define CS42L42_HSBIAS_FILT_REF_RS_SHIFT	3
-#define CS42L42_HSBIAS_FILT_REF_RS_MASK		(1 << \
-					CS42L42_HSBIAS_FILT_REF_RS_SHIFT)
-#define CS42L42_RING_SENSE_PU_HIZ_SHIFT		6
-#define CS42L42_RING_SENSE_PU_HIZ_MASK		(1 << \
-					CS42L42_RING_SENSE_PU_HIZ_SHIFT)
-
-#define CS42L42_RSENSE_CTL2		(CS42L42_PAGE_11 + 0x05)
-#define CS42L42_TS_RS_GATE_SHIFT	7
-#define CS42L42_TS_RS_GATE_MAS		(1 << CS42L42_TS_RS_GATE_SHIFT)
-
-#define CS42L42_OSC_SWITCH		(CS42L42_PAGE_11 + 0x07)
-#define CS42L42_SCLK_PRESENT_SHIFT	0
-#define CS42L42_SCLK_PRESENT_MASK	(1 << CS42L42_SCLK_PRESENT_SHIFT)
-
-#define CS42L42_OSC_SWITCH_STATUS	(CS42L42_PAGE_11 + 0x09)
-#define CS42L42_OSC_SW_SEL_STAT_SHIFT	0
-#define CS42L42_OSC_SW_SEL_STAT_MASK	(3 << CS42L42_OSC_SW_SEL_STAT_SHIFT)
-#define CS42L42_OSC_PDNB_STAT_SHIFT	2
-#define CS42L42_OSC_PDNB_STAT_MASK	(1 << CS42L42_OSC_SW_SEL_STAT_SHIFT)
-
-#define CS42L42_RSENSE_CTL3			(CS42L42_PAGE_11 + 0x12)
-#define CS42L42_RS_RISE_DBNCE_TIME_SHIFT	0
-#define CS42L42_RS_RISE_DBNCE_TIME_MASK		(7 << \
-					CS42L42_RS_RISE_DBNCE_TIME_SHIFT)
-#define CS42L42_RS_FALL_DBNCE_TIME_SHIFT	3
-#define CS42L42_RS_FALL_DBNCE_TIME_MASK		(7 << \
-					CS42L42_RS_FALL_DBNCE_TIME_SHIFT)
-#define CS42L42_RS_PU_EN_SHIFT			6
-#define CS42L42_RS_PU_EN_MASK			(1 << \
-					CS42L42_RS_PU_EN_SHIFT)
-#define CS42L42_RS_INV_SHIFT			7
-#define CS42L42_RS_INV_MASK			(1 << \
-					CS42L42_RS_INV_SHIFT)
-
-#define CS42L42_TSENSE_CTL			(CS42L42_PAGE_11 + 0x13)
-#define CS42L42_TS_RISE_DBNCE_TIME_SHIFT	0
-#define CS42L42_TS_RISE_DBNCE_TIME_MASK		(7 << \
-					CS42L42_TS_RISE_DBNCE_TIME_SHIFT)
-#define CS42L42_TS_FALL_DBNCE_TIME_SHIFT	3
-#define CS42L42_TS_FALL_DBNCE_TIME_MASK		(7 << \
-					CS42L42_TS_FALL_DBNCE_TIME_SHIFT)
-#define CS42L42_TS_INV_SHIFT			7
-#define CS42L42_TS_INV_MASK			(1 << \
-					CS42L42_TS_INV_SHIFT)
-
-#define CS42L42_TSRS_INT_DISABLE	(CS42L42_PAGE_11 + 0x14)
-#define CS42L42_D_RS_PLUG_DBNC_SHIFT	0
-#define CS42L42_D_RS_PLUG_DBNC_MASK	(1 << CS42L42_D_RS_PLUG_DBNC_SHIFT)
-#define CS42L42_D_RS_UNPLUG_DBNC_SHIFT	1
-#define CS42L42_D_RS_UNPLUG_DBNC_MASK	(1 << CS42L42_D_RS_UNPLUG_DBNC_SHIFT)
-#define CS42L42_D_TS_PLUG_DBNC_SHIFT	2
-#define CS42L42_D_TS_PLUG_DBNC_MASK	(1 << CS42L42_D_TS_PLUG_DBNC_SHIFT)
-#define CS42L42_D_TS_UNPLUG_DBNC_SHIFT	3
-#define CS42L42_D_TS_UNPLUG_DBNC_MASK	(1 << CS42L42_D_TS_UNPLUG_DBNC_SHIFT)
-
-#define CS42L42_TRSENSE_STATUS		(CS42L42_PAGE_11 + 0x15)
-#define CS42L42_RS_PLUG_DBNC_SHIFT	0
-#define CS42L42_RS_PLUG_DBNC_MASK	(1 << CS42L42_RS_PLUG_DBNC_SHIFT)
-#define CS42L42_RS_UNPLUG_DBNC_SHIFT	1
-#define CS42L42_RS_UNPLUG_DBNC_MASK	(1 << CS42L42_RS_UNPLUG_DBNC_SHIFT)
-#define CS42L42_TS_PLUG_DBNC_SHIFT	2
-#define CS42L42_TS_PLUG_DBNC_MASK	(1 << CS42L42_TS_PLUG_DBNC_SHIFT)
-#define CS42L42_TS_UNPLUG_DBNC_SHIFT	3
-#define CS42L42_TS_UNPLUG_DBNC_MASK	(1 << CS42L42_TS_UNPLUG_DBNC_SHIFT)
-
-#define CS42L42_HSDET_CTL1		(CS42L42_PAGE_11 + 0x1F)
-#define CS42L42_HSDET_COMP1_LVL_SHIFT	0
-#define CS42L42_HSDET_COMP1_LVL_MASK	(15 << CS42L42_HSDET_COMP1_LVL_SHIFT)
-#define CS42L42_HSDET_COMP2_LVL_SHIFT	4
-#define CS42L42_HSDET_COMP2_LVL_MASK	(15 << CS42L42_HSDET_COMP2_LVL_SHIFT)
-
-#define CS42L42_HSDET_CTL2		(CS42L42_PAGE_11 + 0x20)
-#define CS42L42_HSDET_AUTO_TIME_SHIFT	0
-#define CS42L42_HSDET_AUTO_TIME_MASK	(3 << CS42L42_HSDET_AUTO_TIME_SHIFT)
-#define CS42L42_HSBIAS_REF_SHIFT	3
-#define CS42L42_HSBIAS_REF_MASK		(1 << CS42L42_HSBIAS_REF_SHIFT)
-#define CS42L42_HSDET_SET_SHIFT		4
-#define CS42L42_HSDET_SET_MASK		(3 << CS42L42_HSDET_SET_SHIFT)
-#define CS42L42_HSDET_CTRL_SHIFT	6
-#define CS42L42_HSDET_CTRL_MASK		(3 << CS42L42_HSDET_CTRL_SHIFT)
-
-#define CS42L42_HS_SWITCH_CTL		(CS42L42_PAGE_11 + 0x21)
-#define CS42L42_SW_GNDHS_HS4_SHIFT	0
-#define CS42L42_SW_GNDHS_HS4_MASK	(1 << CS42L42_SW_GNDHS_HS4_SHIFT)
-#define CS42L42_SW_GNDHS_HS3_SHIFT	1
-#define CS42L42_SW_GNDHS_HS3_MASK	(1 << CS42L42_SW_GNDHS_HS3_SHIFT)
-#define CS42L42_SW_HSB_HS4_SHIFT	2
-#define CS42L42_SW_HSB_HS4_MASK		(1 << CS42L42_SW_HSB_HS4_SHIFT)
-#define CS42L42_SW_HSB_HS3_SHIFT	3
-#define CS42L42_SW_HSB_HS3_MASK		(1 << CS42L42_SW_HSB_HS3_SHIFT)
-#define CS42L42_SW_HSB_FILT_HS4_SHIFT	4
-#define CS42L42_SW_HSB_FILT_HS4_MASK	(1 << CS42L42_SW_HSB_FILT_HS4_SHIFT)
-#define CS42L42_SW_HSB_FILT_HS3_SHIFT	5
-#define CS42L42_SW_HSB_FILT_HS3_MASK	(1 << CS42L42_SW_HSB_FILT_HS3_SHIFT)
-#define CS42L42_SW_REF_HS4_SHIFT	6
-#define CS42L42_SW_REF_HS4_MASK		(1 << CS42L42_SW_REF_HS4_SHIFT)
-#define CS42L42_SW_REF_HS3_SHIFT	7
-#define CS42L42_SW_REF_HS3_MASK		(1 << CS42L42_SW_REF_HS3_SHIFT)
-
-#define CS42L42_HS_DET_STATUS		(CS42L42_PAGE_11 + 0x24)
-#define CS42L42_HSDET_TYPE_SHIFT	0
-#define CS42L42_HSDET_TYPE_MASK		(3 << CS42L42_HSDET_TYPE_SHIFT)
-#define CS42L42_HSDET_COMP1_OUT_SHIFT	6
-#define CS42L42_HSDET_COMP1_OUT_MASK	(1 << CS42L42_HSDET_COMP1_OUT_SHIFT)
-#define CS42L42_HSDET_COMP2_OUT_SHIFT	7
-#define CS42L42_HSDET_COMP2_OUT_MASK	(1 << CS42L42_HSDET_COMP2_OUT_SHIFT)
-#define CS42L42_PLUG_CTIA		0
-#define CS42L42_PLUG_OMTP		1
-#define CS42L42_PLUG_HEADPHONE		2
-#define CS42L42_PLUG_INVALID		3
-
-#define CS42L42_HS_CLAMP_DISABLE	(CS42L42_PAGE_11 + 0x29)
-#define CS42L42_HS_CLAMP_DISABLE_SHIFT	0
-#define CS42L42_HS_CLAMP_DISABLE_MASK	(1 << CS42L42_HS_CLAMP_DISABLE_SHIFT)
-
-/* Page 0x12 Clocking Registers */
-#define CS42L42_MCLK_SRC_SEL		(CS42L42_PAGE_12 + 0x01)
-#define CS42L42_MCLKDIV_SHIFT		1
-#define CS42L42_MCLKDIV_MASK		(1 << CS42L42_MCLKDIV_SHIFT)
-#define CS42L42_MCLK_SRC_SEL_SHIFT	0
-#define CS42L42_MCLK_SRC_SEL_MASK	(1 << CS42L42_MCLK_SRC_SEL_SHIFT)
-
-#define CS42L42_SPDIF_CLK_CFG		(CS42L42_PAGE_12 + 0x02)
-#define CS42L42_FSYNC_PW_LOWER		(CS42L42_PAGE_12 + 0x03)
-
-#define CS42L42_FSYNC_PW_UPPER			(CS42L42_PAGE_12 + 0x04)
-#define CS42L42_FSYNC_PULSE_WIDTH_SHIFT		0
-#define CS42L42_FSYNC_PULSE_WIDTH_MASK		(0xff << \
-					CS42L42_FSYNC_PULSE_WIDTH_SHIFT)
-
-#define CS42L42_FSYNC_P_LOWER		(CS42L42_PAGE_12 + 0x05)
-
-#define CS42L42_FSYNC_P_UPPER		(CS42L42_PAGE_12 + 0x06)
-#define CS42L42_FSYNC_PERIOD_SHIFT	0
-#define CS42L42_FSYNC_PERIOD_MASK	(0xff << CS42L42_FSYNC_PERIOD_SHIFT)
-
-#define CS42L42_ASP_CLK_CFG		(CS42L42_PAGE_12 + 0x07)
-#define CS42L42_ASP_SCLK_EN_SHIFT	5
-#define CS42L42_ASP_SCLK_EN_MASK	(1 << CS42L42_ASP_SCLK_EN_SHIFT)
-#define CS42L42_ASP_MASTER_MODE		0x01
-#define CS42L42_ASP_SLAVE_MODE		0x00
-#define CS42L42_ASP_MODE_SHIFT		4
-#define CS42L42_ASP_MODE_MASK		(1 << CS42L42_ASP_MODE_SHIFT)
-#define CS42L42_ASP_SCPOL_SHIFT		2
-#define CS42L42_ASP_SCPOL_MASK		(3 << CS42L42_ASP_SCPOL_SHIFT)
-#define CS42L42_ASP_SCPOL_NOR		3
-#define CS42L42_ASP_LCPOL_SHIFT		0
-#define CS42L42_ASP_LCPOL_MASK		(3 << CS42L42_ASP_LCPOL_SHIFT)
-#define CS42L42_ASP_LCPOL_INV		3
-
-#define CS42L42_ASP_FRM_CFG		(CS42L42_PAGE_12 + 0x08)
-#define CS42L42_ASP_STP_SHIFT		4
-#define CS42L42_ASP_STP_MASK		(1 << CS42L42_ASP_STP_SHIFT)
-#define CS42L42_ASP_5050_SHIFT		3
-#define CS42L42_ASP_5050_MASK		(1 << CS42L42_ASP_5050_SHIFT)
-#define CS42L42_ASP_FSD_SHIFT		0
-#define CS42L42_ASP_FSD_MASK		(7 << CS42L42_ASP_FSD_SHIFT)
-#define CS42L42_ASP_FSD_0_5		1
-#define CS42L42_ASP_FSD_1_0		2
-#define CS42L42_ASP_FSD_1_5		3
-#define CS42L42_ASP_FSD_2_0		4
-
-#define CS42L42_FS_RATE_EN		(CS42L42_PAGE_12 + 0x09)
-#define CS42L42_FS_EN_SHIFT		0
-#define CS42L42_FS_EN_MASK		(0xf << CS42L42_FS_EN_SHIFT)
-#define CS42L42_FS_EN_IASRC_96K		0x1
-#define CS42L42_FS_EN_OASRC_96K		0x2
-
-#define CS42L42_IN_ASRC_CLK		(CS42L42_PAGE_12 + 0x0A)
-#define CS42L42_CLK_IASRC_SEL_SHIFT	0
-#define CS42L42_CLK_IASRC_SEL_MASK	(1 << CS42L42_CLK_IASRC_SEL_SHIFT)
-#define CS42L42_CLK_IASRC_SEL_12	1
-
-#define CS42L42_OUT_ASRC_CLK		(CS42L42_PAGE_12 + 0x0B)
-#define CS42L42_CLK_OASRC_SEL_SHIFT	0
-#define CS42L42_CLK_OASRC_SEL_MASK	(1 << CS42L42_CLK_OASRC_SEL_SHIFT)
-#define CS42L42_CLK_OASRC_SEL_12	1
-
-#define CS42L42_PLL_DIV_CFG1		(CS42L42_PAGE_12 + 0x0C)
-#define CS42L42_SCLK_PREDIV_SHIFT	0
-#define CS42L42_SCLK_PREDIV_MASK	(3 << CS42L42_SCLK_PREDIV_SHIFT)
-
-/* Page 0x13 Interrupt Registers */
-/* Interrupts */
-#define CS42L42_ADC_OVFL_STATUS		(CS42L42_PAGE_13 + 0x01)
-#define CS42L42_MIXER_STATUS		(CS42L42_PAGE_13 + 0x02)
-#define CS42L42_SRC_STATUS		(CS42L42_PAGE_13 + 0x03)
-#define CS42L42_ASP_RX_STATUS		(CS42L42_PAGE_13 + 0x04)
-#define CS42L42_ASP_TX_STATUS		(CS42L42_PAGE_13 + 0x05)
-#define CS42L42_CODEC_STATUS		(CS42L42_PAGE_13 + 0x08)
-#define CS42L42_DET_INT_STATUS1		(CS42L42_PAGE_13 + 0x09)
-#define CS42L42_DET_INT_STATUS2		(CS42L42_PAGE_13 + 0x0A)
-#define CS42L42_SRCPL_INT_STATUS	(CS42L42_PAGE_13 + 0x0B)
-#define CS42L42_VPMON_STATUS		(CS42L42_PAGE_13 + 0x0D)
-#define CS42L42_PLL_LOCK_STATUS		(CS42L42_PAGE_13 + 0x0E)
-#define CS42L42_TSRS_PLUG_STATUS	(CS42L42_PAGE_13 + 0x0F)
-/* Masks */
-#define CS42L42_ADC_OVFL_INT_MASK	(CS42L42_PAGE_13 + 0x16)
-#define CS42L42_ADC_OVFL_SHIFT		0
-#define CS42L42_ADC_OVFL_MASK		(1 << CS42L42_ADC_OVFL_SHIFT)
-#define CS42L42_ADC_OVFL_VAL_MASK	CS42L42_ADC_OVFL_MASK
-
-#define CS42L42_MIXER_INT_MASK		(CS42L42_PAGE_13 + 0x17)
-#define CS42L42_MIX_CHB_OVFL_SHIFT	0
-#define CS42L42_MIX_CHB_OVFL_MASK	(1 << CS42L42_MIX_CHB_OVFL_SHIFT)
-#define CS42L42_MIX_CHA_OVFL_SHIFT	1
-#define CS42L42_MIX_CHA_OVFL_MASK	(1 << CS42L42_MIX_CHA_OVFL_SHIFT)
-#define CS42L42_EQ_OVFL_SHIFT		2
-#define CS42L42_EQ_OVFL_MASK		(1 << CS42L42_EQ_OVFL_SHIFT)
-#define CS42L42_EQ_BIQUAD_OVFL_SHIFT	3
-#define CS42L42_EQ_BIQUAD_OVFL_MASK	(1 << CS42L42_EQ_BIQUAD_OVFL_SHIFT)
-#define CS42L42_MIXER_VAL_MASK		(CS42L42_MIX_CHB_OVFL_MASK | \
-					CS42L42_MIX_CHA_OVFL_MASK | \
-					CS42L42_EQ_OVFL_MASK | \
-					CS42L42_EQ_BIQUAD_OVFL_MASK)
-
-#define CS42L42_SRC_INT_MASK		(CS42L42_PAGE_13 + 0x18)
-#define CS42L42_SRC_ILK_SHIFT		0
-#define CS42L42_SRC_ILK_MASK		(1 << CS42L42_SRC_ILK_SHIFT)
-#define CS42L42_SRC_OLK_SHIFT		1
-#define CS42L42_SRC_OLK_MASK		(1 << CS42L42_SRC_OLK_SHIFT)
-#define CS42L42_SRC_IUNLK_SHIFT		2
-#define CS42L42_SRC_IUNLK_MASK		(1 << CS42L42_SRC_IUNLK_SHIFT)
-#define CS42L42_SRC_OUNLK_SHIFT		3
-#define CS42L42_SRC_OUNLK_MASK		(1 << CS42L42_SRC_OUNLK_SHIFT)
-#define CS42L42_SRC_VAL_MASK		(CS42L42_SRC_ILK_MASK | \
-					CS42L42_SRC_OLK_MASK | \
-					CS42L42_SRC_IUNLK_MASK | \
-					CS42L42_SRC_OUNLK_MASK)
-
-#define CS42L42_ASP_RX_INT_MASK		(CS42L42_PAGE_13 + 0x19)
-#define CS42L42_ASPRX_NOLRCK_SHIFT	0
-#define CS42L42_ASPRX_NOLRCK_MASK	(1 << CS42L42_ASPRX_NOLRCK_SHIFT)
-#define CS42L42_ASPRX_EARLY_SHIFT	1
-#define CS42L42_ASPRX_EARLY_MASK	(1 << CS42L42_ASPRX_EARLY_SHIFT)
-#define CS42L42_ASPRX_LATE_SHIFT	2
-#define CS42L42_ASPRX_LATE_MASK		(1 << CS42L42_ASPRX_LATE_SHIFT)
-#define CS42L42_ASPRX_ERROR_SHIFT	3
-#define CS42L42_ASPRX_ERROR_MASK	(1 << CS42L42_ASPRX_ERROR_SHIFT)
-#define CS42L42_ASPRX_OVLD_SHIFT	4
-#define CS42L42_ASPRX_OVLD_MASK		(1 << CS42L42_ASPRX_OVLD_SHIFT)
-#define CS42L42_ASP_RX_VAL_MASK		(CS42L42_ASPRX_NOLRCK_MASK | \
-					CS42L42_ASPRX_EARLY_MASK | \
-					CS42L42_ASPRX_LATE_MASK | \
-					CS42L42_ASPRX_ERROR_MASK | \
-					CS42L42_ASPRX_OVLD_MASK)
-
-#define CS42L42_ASP_TX_INT_MASK		(CS42L42_PAGE_13 + 0x1A)
-#define CS42L42_ASPTX_NOLRCK_SHIFT	0
-#define CS42L42_ASPTX_NOLRCK_MASK	(1 << CS42L42_ASPTX_NOLRCK_SHIFT)
-#define CS42L42_ASPTX_EARLY_SHIFT	1
-#define CS42L42_ASPTX_EARLY_MASK	(1 << CS42L42_ASPTX_EARLY_SHIFT)
-#define CS42L42_ASPTX_LATE_SHIFT	2
-#define CS42L42_ASPTX_LATE_MASK		(1 << CS42L42_ASPTX_LATE_SHIFT)
-#define CS42L42_ASPTX_SMERROR_SHIFT	3
-#define CS42L42_ASPTX_SMERROR_MASK	(1 << CS42L42_ASPTX_SMERROR_SHIFT)
-#define CS42L42_ASP_TX_VAL_MASK		(CS42L42_ASPTX_NOLRCK_MASK | \
-					CS42L42_ASPTX_EARLY_MASK | \
-					CS42L42_ASPTX_LATE_MASK | \
-					CS42L42_ASPTX_SMERROR_MASK)
-
-#define CS42L42_CODEC_INT_MASK		(CS42L42_PAGE_13 + 0x1B)
-#define CS42L42_PDN_DONE_SHIFT		0
-#define CS42L42_PDN_DONE_MASK		(1 << CS42L42_PDN_DONE_SHIFT)
-#define CS42L42_HSDET_AUTO_DONE_SHIFT	1
-#define CS42L42_HSDET_AUTO_DONE_MASK	(1 << CS42L42_HSDET_AUTO_DONE_SHIFT)
-#define CS42L42_CODEC_VAL_MASK		(CS42L42_PDN_DONE_MASK | \
-					CS42L42_HSDET_AUTO_DONE_MASK)
-
-#define CS42L42_SRCPL_INT_MASK		(CS42L42_PAGE_13 + 0x1C)
-#define CS42L42_SRCPL_ADC_LK_SHIFT	0
-#define CS42L42_SRCPL_ADC_LK_MASK	(1 << CS42L42_SRCPL_ADC_LK_SHIFT)
-#define CS42L42_SRCPL_DAC_LK_SHIFT	2
-#define CS42L42_SRCPL_DAC_LK_MASK	(1 << CS42L42_SRCPL_DAC_LK_SHIFT)
-#define CS42L42_SRCPL_ADC_UNLK_SHIFT	5
-#define CS42L42_SRCPL_ADC_UNLK_MASK	(1 << CS42L42_SRCPL_ADC_UNLK_SHIFT)
-#define CS42L42_SRCPL_DAC_UNLK_SHIFT	6
-#define CS42L42_SRCPL_DAC_UNLK_MASK	(1 << CS42L42_SRCPL_DAC_UNLK_SHIFT)
-#define CS42L42_SRCPL_VAL_MASK		(CS42L42_SRCPL_ADC_LK_MASK | \
-					CS42L42_SRCPL_DAC_LK_MASK | \
-					CS42L42_SRCPL_ADC_UNLK_MASK | \
-					CS42L42_SRCPL_DAC_UNLK_MASK)
-
-#define CS42L42_VPMON_INT_MASK		(CS42L42_PAGE_13 + 0x1E)
-#define CS42L42_VPMON_SHIFT		0
-#define CS42L42_VPMON_MASK		(1 << CS42L42_VPMON_SHIFT)
-#define CS42L42_VPMON_VAL_MASK		CS42L42_VPMON_MASK
-
-#define CS42L42_PLL_LOCK_INT_MASK	(CS42L42_PAGE_13 + 0x1F)
-#define CS42L42_PLL_LOCK_SHIFT		0
-#define CS42L42_PLL_LOCK_MASK		(1 << CS42L42_PLL_LOCK_SHIFT)
-#define CS42L42_PLL_LOCK_VAL_MASK	CS42L42_PLL_LOCK_MASK
-
-#define CS42L42_TSRS_PLUG_INT_MASK	(CS42L42_PAGE_13 + 0x20)
-#define CS42L42_RS_PLUG_SHIFT		0
-#define CS42L42_RS_PLUG_MASK		(1 << CS42L42_RS_PLUG_SHIFT)
-#define CS42L42_RS_UNPLUG_SHIFT		1
-#define CS42L42_RS_UNPLUG_MASK		(1 << CS42L42_RS_UNPLUG_SHIFT)
-#define CS42L42_TS_PLUG_SHIFT		2
-#define CS42L42_TS_PLUG_MASK		(1 << CS42L42_TS_PLUG_SHIFT)
-#define CS42L42_TS_UNPLUG_SHIFT		3
-#define CS42L42_TS_UNPLUG_MASK		(1 << CS42L42_TS_UNPLUG_SHIFT)
-#define CS42L42_TSRS_PLUG_VAL_MASK	(CS42L42_RS_PLUG_MASK | \
-					CS42L42_RS_UNPLUG_MASK | \
-					CS42L42_TS_PLUG_MASK | \
-					CS42L42_TS_UNPLUG_MASK)
-#define CS42L42_TS_PLUG			3
-#define CS42L42_TS_UNPLUG		0
-#define CS42L42_TS_TRANS		1
-
-/* Page 0x15 Fractional-N PLL Registers */
-#define CS42L42_PLL_CTL1		(CS42L42_PAGE_15 + 0x01)
-#define CS42L42_PLL_START_SHIFT		0
-#define CS42L42_PLL_START_MASK		(1 << CS42L42_PLL_START_SHIFT)
-
-#define CS42L42_PLL_DIV_FRAC0		(CS42L42_PAGE_15 + 0x02)
-#define CS42L42_PLL_DIV_FRAC_SHIFT	0
-#define CS42L42_PLL_DIV_FRAC_MASK	(0xff << CS42L42_PLL_DIV_FRAC_SHIFT)
-
-#define CS42L42_PLL_DIV_FRAC1		(CS42L42_PAGE_15 + 0x03)
-#define CS42L42_PLL_DIV_FRAC2		(CS42L42_PAGE_15 + 0x04)
-
-#define CS42L42_PLL_DIV_INT		(CS42L42_PAGE_15 + 0x05)
-#define CS42L42_PLL_DIV_INT_SHIFT	0
-#define CS42L42_PLL_DIV_INT_MASK	(0xff << CS42L42_PLL_DIV_INT_SHIFT)
-
-#define CS42L42_PLL_CTL3		(CS42L42_PAGE_15 + 0x08)
-#define CS42L42_PLL_DIVOUT_SHIFT	0
-#define CS42L42_PLL_DIVOUT_MASK		(0xff << CS42L42_PLL_DIVOUT_SHIFT)
-
-#define CS42L42_PLL_CAL_RATIO		(CS42L42_PAGE_15 + 0x0A)
-#define CS42L42_PLL_CAL_RATIO_SHIFT	0
-#define CS42L42_PLL_CAL_RATIO_MASK	(0xff << CS42L42_PLL_CAL_RATIO_SHIFT)
-
-#define CS42L42_PLL_CTL4		(CS42L42_PAGE_15 + 0x1B)
-#define CS42L42_PLL_MODE_SHIFT		0
-#define CS42L42_PLL_MODE_MASK		(3 << CS42L42_PLL_MODE_SHIFT)
-
-/* Page 0x19 HP Load Detect Registers */
-#define CS42L42_LOAD_DET_RCSTAT		(CS42L42_PAGE_19 + 0x25)
-#define CS42L42_RLA_STAT_SHIFT		0
-#define CS42L42_RLA_STAT_MASK		(3 << CS42L42_RLA_STAT_SHIFT)
-#define CS42L42_RLA_STAT_15_OHM		0
-
-#define CS42L42_LOAD_DET_DONE		(CS42L42_PAGE_19 + 0x26)
-#define CS42L42_HPLOAD_DET_DONE_SHIFT	0
-#define CS42L42_HPLOAD_DET_DONE_MASK	(1 << CS42L42_HPLOAD_DET_DONE_SHIFT)
-
-#define CS42L42_LOAD_DET_EN		(CS42L42_PAGE_19 + 0x27)
-#define CS42L42_HP_LD_EN_SHIFT		0
-#define CS42L42_HP_LD_EN_MASK		(1 << CS42L42_HP_LD_EN_SHIFT)
-
-/* Page 0x1B Headset Interface Registers */
-#define CS42L42_HSBIAS_SC_AUTOCTL		(CS42L42_PAGE_1B + 0x70)
-#define CS42L42_HSBIAS_SENSE_TRIP_SHIFT		0
-#define CS42L42_HSBIAS_SENSE_TRIP_MASK		(7 << \
-					CS42L42_HSBIAS_SENSE_TRIP_SHIFT)
-#define CS42L42_TIP_SENSE_EN_SHIFT		5
-#define CS42L42_TIP_SENSE_EN_MASK		(1 << \
-					CS42L42_TIP_SENSE_EN_SHIFT)
-#define CS42L42_AUTO_HSBIAS_HIZ_SHIFT		6
-#define CS42L42_AUTO_HSBIAS_HIZ_MASK		(1 << \
-					CS42L42_AUTO_HSBIAS_HIZ_SHIFT)
-#define CS42L42_HSBIAS_SENSE_EN_SHIFT		7
-#define CS42L42_HSBIAS_SENSE_EN_MASK		(1 << \
-					CS42L42_HSBIAS_SENSE_EN_SHIFT)
-
-#define CS42L42_WAKE_CTL		(CS42L42_PAGE_1B + 0x71)
-#define CS42L42_WAKEB_CLEAR_SHIFT	0
-#define CS42L42_WAKEB_CLEAR_MASK	(1 << CS42L42_WAKEB_CLEAR_SHIFT)
-#define CS42L42_WAKEB_MODE_SHIFT	5
-#define CS42L42_WAKEB_MODE_MASK		(1 << CS42L42_WAKEB_MODE_SHIFT)
-#define CS42L42_M_HP_WAKE_SHIFT		6
-#define CS42L42_M_HP_WAKE_MASK		(1 << CS42L42_M_HP_WAKE_SHIFT)
-#define CS42L42_M_MIC_WAKE_SHIFT	7
-#define CS42L42_M_MIC_WAKE_MASK		(1 << CS42L42_M_MIC_WAKE_SHIFT)
-
-#define CS42L42_ADC_DISABLE_MUTE		(CS42L42_PAGE_1B + 0x72)
-#define CS42L42_ADC_DISABLE_S0_MUTE_SHIFT	7
-#define CS42L42_ADC_DISABLE_S0_MUTE_MASK	(1 << \
-					CS42L42_ADC_DISABLE_S0_MUTE_SHIFT)
-
-#define CS42L42_TIPSENSE_CTL			(CS42L42_PAGE_1B + 0x73)
-#define CS42L42_TIP_SENSE_DEBOUNCE_SHIFT	0
-#define CS42L42_TIP_SENSE_DEBOUNCE_MASK		(3 << \
-					CS42L42_TIP_SENSE_DEBOUNCE_SHIFT)
-#define CS42L42_TIP_SENSE_INV_SHIFT		5
-#define CS42L42_TIP_SENSE_INV_MASK		(1 << \
-					CS42L42_TIP_SENSE_INV_SHIFT)
-#define CS42L42_TIP_SENSE_CTRL_SHIFT		6
-#define CS42L42_TIP_SENSE_CTRL_MASK		(3 << \
-					CS42L42_TIP_SENSE_CTRL_SHIFT)
-
-#define CS42L42_MISC_DET_CTL		(CS42L42_PAGE_1B + 0x74)
-#define CS42L42_PDN_MIC_LVL_DET_SHIFT	0
-#define CS42L42_PDN_MIC_LVL_DET_MASK	(1 << CS42L42_PDN_MIC_LVL_DET_SHIFT)
-#define CS42L42_HSBIAS_CTL_SHIFT	1
-#define CS42L42_HSBIAS_CTL_MASK		(3 << CS42L42_HSBIAS_CTL_SHIFT)
-#define CS42L42_DETECT_MODE_SHIFT	3
-#define CS42L42_DETECT_MODE_MASK	(3 << CS42L42_DETECT_MODE_SHIFT)
-
-#define CS42L42_MIC_DET_CTL1		(CS42L42_PAGE_1B + 0x75)
-#define CS42L42_HS_DET_LEVEL_SHIFT	0
-#define CS42L42_HS_DET_LEVEL_MASK	(0x3F << CS42L42_HS_DET_LEVEL_SHIFT)
-#define CS42L42_EVENT_STAT_SEL_SHIFT	6
-#define CS42L42_EVENT_STAT_SEL_MASK	(1 << CS42L42_EVENT_STAT_SEL_SHIFT)
-#define CS42L42_LATCH_TO_VP_SHIFT	7
-#define CS42L42_LATCH_TO_VP_MASK	(1 << CS42L42_LATCH_TO_VP_SHIFT)
-
-#define CS42L42_MIC_DET_CTL2		(CS42L42_PAGE_1B + 0x76)
-#define CS42L42_DEBOUNCE_TIME_SHIFT	5
-#define CS42L42_DEBOUNCE_TIME_MASK	(0x07 << CS42L42_DEBOUNCE_TIME_SHIFT)
-
-#define CS42L42_DET_STATUS1		(CS42L42_PAGE_1B + 0x77)
-#define CS42L42_HSBIAS_HIZ_MODE_SHIFT	6
-#define CS42L42_HSBIAS_HIZ_MODE_MASK	(1 << CS42L42_HSBIAS_HIZ_MODE_SHIFT)
-#define CS42L42_TIP_SENSE_SHIFT		7
-#define CS42L42_TIP_SENSE_MASK		(1 << CS42L42_TIP_SENSE_SHIFT)
-
-#define CS42L42_DET_STATUS2		(CS42L42_PAGE_1B + 0x78)
-#define CS42L42_SHORT_TRUE_SHIFT	0
-#define CS42L42_SHORT_TRUE_MASK		(1 << CS42L42_SHORT_TRUE_SHIFT)
-#define CS42L42_HS_TRUE_SHIFT	1
-#define CS42L42_HS_TRUE_MASK		(1 << CS42L42_HS_TRUE_SHIFT)
-
-#define CS42L42_DET_INT1_MASK		(CS42L42_PAGE_1B + 0x79)
-#define CS42L42_TIP_SENSE_UNPLUG_SHIFT	5
-#define CS42L42_TIP_SENSE_UNPLUG_MASK	(1 << CS42L42_TIP_SENSE_UNPLUG_SHIFT)
-#define CS42L42_TIP_SENSE_PLUG_SHIFT	6
-#define CS42L42_TIP_SENSE_PLUG_MASK	(1 << CS42L42_TIP_SENSE_PLUG_SHIFT)
-#define CS42L42_HSBIAS_SENSE_SHIFT	7
-#define CS42L42_HSBIAS_SENSE_MASK	(1 << CS42L42_HSBIAS_SENSE_SHIFT)
-#define CS42L42_DET_INT_VAL1_MASK	(CS42L42_TIP_SENSE_UNPLUG_MASK | \
-					CS42L42_TIP_SENSE_PLUG_MASK | \
-					CS42L42_HSBIAS_SENSE_MASK)
-
-#define CS42L42_DET_INT2_MASK		(CS42L42_PAGE_1B + 0x7A)
-#define CS42L42_M_SHORT_DET_SHIFT	0
-#define CS42L42_M_SHORT_DET_MASK	(1 << \
-					CS42L42_M_SHORT_DET_SHIFT)
-#define CS42L42_M_SHORT_RLS_SHIFT	1
-#define CS42L42_M_SHORT_RLS_MASK	(1 << \
-					CS42L42_M_SHORT_RLS_SHIFT)
-#define CS42L42_M_HSBIAS_HIZ_SHIFT	2
-#define CS42L42_M_HSBIAS_HIZ_MASK	(1 << \
-					CS42L42_M_HSBIAS_HIZ_SHIFT)
-#define CS42L42_M_DETECT_FT_SHIFT	6
-#define CS42L42_M_DETECT_FT_MASK	(1 << \
-					CS42L42_M_DETECT_FT_SHIFT)
-#define CS42L42_M_DETECT_TF_SHIFT	7
-#define CS42L42_M_DETECT_TF_MASK	(1 << \
-					CS42L42_M_DETECT_TF_SHIFT)
-#define CS42L42_DET_INT_VAL2_MASK	(CS42L42_M_SHORT_DET_MASK | \
-					CS42L42_M_SHORT_RLS_MASK | \
-					CS42L42_M_HSBIAS_HIZ_MASK | \
-					CS42L42_M_DETECT_FT_MASK | \
-					CS42L42_M_DETECT_TF_MASK)
-
-/* Page 0x1C Headset Bias Registers */
-#define CS42L42_HS_BIAS_CTL		(CS42L42_PAGE_1C + 0x03)
-#define CS42L42_HSBIAS_RAMP_SHIFT	0
-#define CS42L42_HSBIAS_RAMP_MASK	(3 << CS42L42_HSBIAS_RAMP_SHIFT)
-#define CS42L42_HSBIAS_PD_SHIFT		4
-#define CS42L42_HSBIAS_PD_MASK		(1 << CS42L42_HSBIAS_PD_SHIFT)
-#define CS42L42_HSBIAS_CAPLESS_SHIFT	7
-#define CS42L42_HSBIAS_CAPLESS_MASK	(1 << CS42L42_HSBIAS_CAPLESS_SHIFT)
-
-/* Page 0x1D ADC Registers */
-#define CS42L42_ADC_CTL			(CS42L42_PAGE_1D + 0x01)
-#define CS42L42_ADC_NOTCH_DIS_SHIFT		5
-#define CS42L42_ADC_FORCE_WEAK_VCM_SHIFT	4
-#define CS42L42_ADC_INV_SHIFT			2
-#define CS42L42_ADC_DIG_BOOST_SHIFT		0
-
-#define CS42L42_ADC_VOLUME		(CS42L42_PAGE_1D + 0x03)
-#define CS42L42_ADC_VOL_SHIFT		0
-
-#define CS42L42_ADC_WNF_HPF_CTL		(CS42L42_PAGE_1D + 0x04)
-#define CS42L42_ADC_WNF_CF_SHIFT	4
-#define CS42L42_ADC_WNF_EN_SHIFT	3
-#define CS42L42_ADC_HPF_CF_SHIFT	1
-#define CS42L42_ADC_HPF_EN_SHIFT	0
-
-/* Page 0x1F DAC Registers */
-#define CS42L42_DAC_CTL1		(CS42L42_PAGE_1F + 0x01)
-#define CS42L42_DACB_INV_SHIFT		1
-#define CS42L42_DACA_INV_SHIFT		0
-
-#define CS42L42_DAC_CTL2		(CS42L42_PAGE_1F + 0x06)
-#define CS42L42_HPOUT_PULLDOWN_SHIFT	4
-#define CS42L42_HPOUT_PULLDOWN_MASK	(15 << CS42L42_HPOUT_PULLDOWN_SHIFT)
-#define CS42L42_HPOUT_LOAD_SHIFT	3
-#define CS42L42_HPOUT_LOAD_MASK		(1 << CS42L42_HPOUT_LOAD_SHIFT)
-#define CS42L42_HPOUT_CLAMP_SHIFT	2
-#define CS42L42_HPOUT_CLAMP_MASK	(1 << CS42L42_HPOUT_CLAMP_SHIFT)
-#define CS42L42_DAC_HPF_EN_SHIFT	1
-#define CS42L42_DAC_HPF_EN_MASK		(1 << CS42L42_DAC_HPF_EN_SHIFT)
-#define CS42L42_DAC_MON_EN_SHIFT	0
-#define CS42L42_DAC_MON_EN_MASK		(1 << CS42L42_DAC_MON_EN_SHIFT)
-
-/* Page 0x20 HP CTL Registers */
-#define CS42L42_HP_CTL			(CS42L42_PAGE_20 + 0x01)
-#define CS42L42_HP_ANA_BMUTE_SHIFT	3
-#define CS42L42_HP_ANA_BMUTE_MASK	(1 << CS42L42_HP_ANA_BMUTE_SHIFT)
-#define CS42L42_HP_ANA_AMUTE_SHIFT	2
-#define CS42L42_HP_ANA_AMUTE_MASK	(1 << CS42L42_HP_ANA_AMUTE_SHIFT)
-#define CS42L42_HP_FULL_SCALE_VOL_SHIFT	1
-#define CS42L42_HP_FULL_SCALE_VOL_MASK	(1 << CS42L42_HP_FULL_SCALE_VOL_SHIFT)
-
-/* Page 0x21 Class H Registers */
-#define CS42L42_CLASSH_CTL		(CS42L42_PAGE_21 + 0x01)
-
-/* Page 0x23 Mixer Volume Registers */
-#define CS42L42_MIXER_CHA_VOL		(CS42L42_PAGE_23 + 0x01)
-#define CS42L42_MIXER_ADC_VOL		(CS42L42_PAGE_23 + 0x02)
-
-#define CS42L42_MIXER_CHB_VOL		(CS42L42_PAGE_23 + 0x03)
-#define CS42L42_MIXER_CH_VOL_SHIFT	0
-#define CS42L42_MIXER_CH_VOL_MASK	(0x3f << CS42L42_MIXER_CH_VOL_SHIFT)
-
-/* Page 0x24 EQ Registers */
-#define CS42L42_EQ_COEF_IN0		(CS42L42_PAGE_24 + 0x01)
-#define CS42L42_EQ_COEF_IN1		(CS42L42_PAGE_24 + 0x02)
-#define CS42L42_EQ_COEF_IN2		(CS42L42_PAGE_24 + 0x03)
-#define CS42L42_EQ_COEF_IN3		(CS42L42_PAGE_24 + 0x04)
-#define CS42L42_EQ_COEF_RW		(CS42L42_PAGE_24 + 0x06)
-#define CS42L42_EQ_COEF_OUT0		(CS42L42_PAGE_24 + 0x07)
-#define CS42L42_EQ_COEF_OUT1		(CS42L42_PAGE_24 + 0x08)
-#define CS42L42_EQ_COEF_OUT2		(CS42L42_PAGE_24 + 0x09)
-#define CS42L42_EQ_COEF_OUT3		(CS42L42_PAGE_24 + 0x0A)
-#define CS42L42_EQ_INIT_STAT		(CS42L42_PAGE_24 + 0x0B)
-#define CS42L42_EQ_START_FILT		(CS42L42_PAGE_24 + 0x0C)
-#define CS42L42_EQ_MUTE_CTL		(CS42L42_PAGE_24 + 0x0E)
-
-/* Page 0x25 Audio Port Registers */
-#define CS42L42_SP_RX_CH_SEL		(CS42L42_PAGE_25 + 0x01)
-#define CS42L42_SP_RX_CHB_SEL_SHIFT	2
-#define CS42L42_SP_RX_CHB_SEL_MASK	(3 << CS42L42_SP_RX_CHB_SEL_SHIFT)
-
-#define CS42L42_SP_RX_ISOC_CTL		(CS42L42_PAGE_25 + 0x02)
-#define CS42L42_SP_RX_RSYNC_SHIFT	6
-#define CS42L42_SP_RX_RSYNC_MASK	(1 << CS42L42_SP_RX_RSYNC_SHIFT)
-#define CS42L42_SP_RX_NSB_POS_SHIFT	3
-#define CS42L42_SP_RX_NSB_POS_MASK	(7 << CS42L42_SP_RX_NSB_POS_SHIFT)
-#define CS42L42_SP_RX_NFS_NSBB_SHIFT	2
-#define CS42L42_SP_RX_NFS_NSBB_MASK	(1 << CS42L42_SP_RX_NFS_NSBB_SHIFT)
-#define CS42L42_SP_RX_ISOC_MODE_SHIFT	0
-#define CS42L42_SP_RX_ISOC_MODE_MASK	(3 << CS42L42_SP_RX_ISOC_MODE_SHIFT)
-
-#define CS42L42_SP_RX_FS		(CS42L42_PAGE_25 + 0x03)
-#define CS42l42_SPDIF_CH_SEL		(CS42L42_PAGE_25 + 0x04)
-#define CS42L42_SP_TX_ISOC_CTL		(CS42L42_PAGE_25 + 0x05)
-#define CS42L42_SP_TX_FS		(CS42L42_PAGE_25 + 0x06)
-#define CS42L42_SPDIF_SW_CTL1		(CS42L42_PAGE_25 + 0x07)
-
-/* Page 0x26 SRC Registers */
-#define CS42L42_SRC_SDIN_FS		(CS42L42_PAGE_26 + 0x01)
-#define CS42L42_SRC_SDIN_FS_SHIFT	0
-#define CS42L42_SRC_SDIN_FS_MASK	(0x1f << CS42L42_SRC_SDIN_FS_SHIFT)
-
-#define CS42L42_SRC_SDOUT_FS		(CS42L42_PAGE_26 + 0x09)
-
-/* Page 0x28 S/PDIF Registers */
-#define CS42L42_SPDIF_CTL1		(CS42L42_PAGE_28 + 0x01)
-#define CS42L42_SPDIF_CTL2		(CS42L42_PAGE_28 + 0x02)
-#define CS42L42_SPDIF_CTL3		(CS42L42_PAGE_28 + 0x03)
-#define CS42L42_SPDIF_CTL4		(CS42L42_PAGE_28 + 0x04)
-
-/* Page 0x29 Serial Port TX Registers */
-#define CS42L42_ASP_TX_SZ_EN		(CS42L42_PAGE_29 + 0x01)
-#define CS42L42_ASP_TX_EN_SHIFT		0
-#define CS42L42_ASP_TX_CH_EN		(CS42L42_PAGE_29 + 0x02)
-#define CS42L42_ASP_TX0_CH2_SHIFT	1
-#define CS42L42_ASP_TX0_CH1_SHIFT	0
-
-#define CS42L42_ASP_TX_CH_AP_RES	(CS42L42_PAGE_29 + 0x03)
-#define CS42L42_ASP_TX_CH1_AP_SHIFT	7
-#define CS42L42_ASP_TX_CH1_AP_MASK	(1 << CS42L42_ASP_TX_CH1_AP_SHIFT)
-#define CS42L42_ASP_TX_CH2_AP_SHIFT	6
-#define CS42L42_ASP_TX_CH2_AP_MASK	(1 << CS42L42_ASP_TX_CH2_AP_SHIFT)
-#define CS42L42_ASP_TX_CH2_RES_SHIFT	2
-#define CS42L42_ASP_TX_CH2_RES_MASK	(3 << CS42L42_ASP_TX_CH2_RES_SHIFT)
-#define CS42L42_ASP_TX_CH1_RES_SHIFT	0
-#define CS42L42_ASP_TX_CH1_RES_MASK	(3 << CS42L42_ASP_TX_CH1_RES_SHIFT)
-#define CS42L42_ASP_TX_CH1_BIT_MSB	(CS42L42_PAGE_29 + 0x04)
-#define CS42L42_ASP_TX_CH1_BIT_LSB	(CS42L42_PAGE_29 + 0x05)
-#define CS42L42_ASP_TX_HIZ_DLY_CFG	(CS42L42_PAGE_29 + 0x06)
-#define CS42L42_ASP_TX_CH2_BIT_MSB	(CS42L42_PAGE_29 + 0x0A)
-#define CS42L42_ASP_TX_CH2_BIT_LSB	(CS42L42_PAGE_29 + 0x0B)
-
-/* Page 0x2A Serial Port RX Registers */
-#define CS42L42_ASP_RX_DAI0_EN		(CS42L42_PAGE_2A + 0x01)
-#define CS42L42_ASP_RX0_CH_EN_SHIFT	2
-#define CS42L42_ASP_RX0_CH_EN_MASK	(0xf << CS42L42_ASP_RX0_CH_EN_SHIFT)
-#define CS42L42_ASP_RX0_CH1_SHIFT	2
-#define CS42L42_ASP_RX0_CH2_SHIFT	3
-#define CS42L42_ASP_RX0_CH3_SHIFT	4
-#define CS42L42_ASP_RX0_CH4_SHIFT	5
-
-#define CS42L42_ASP_RX_DAI0_CH1_AP_RES	(CS42L42_PAGE_2A + 0x02)
-#define CS42L42_ASP_RX_DAI0_CH1_BIT_MSB	(CS42L42_PAGE_2A + 0x03)
-#define CS42L42_ASP_RX_DAI0_CH1_BIT_LSB	(CS42L42_PAGE_2A + 0x04)
-#define CS42L42_ASP_RX_DAI0_CH2_AP_RES	(CS42L42_PAGE_2A + 0x05)
-#define CS42L42_ASP_RX_DAI0_CH2_BIT_MSB	(CS42L42_PAGE_2A + 0x06)
-#define CS42L42_ASP_RX_DAI0_CH2_BIT_LSB	(CS42L42_PAGE_2A + 0x07)
-#define CS42L42_ASP_RX_DAI0_CH3_AP_RES	(CS42L42_PAGE_2A + 0x08)
-#define CS42L42_ASP_RX_DAI0_CH3_BIT_MSB	(CS42L42_PAGE_2A + 0x09)
-#define CS42L42_ASP_RX_DAI0_CH3_BIT_LSB	(CS42L42_PAGE_2A + 0x0A)
-#define CS42L42_ASP_RX_DAI0_CH4_AP_RES	(CS42L42_PAGE_2A + 0x0B)
-#define CS42L42_ASP_RX_DAI0_CH4_BIT_MSB	(CS42L42_PAGE_2A + 0x0C)
-#define CS42L42_ASP_RX_DAI0_CH4_BIT_LSB	(CS42L42_PAGE_2A + 0x0D)
-#define CS42L42_ASP_RX_DAI1_CH1_AP_RES	(CS42L42_PAGE_2A + 0x0E)
-#define CS42L42_ASP_RX_DAI1_CH1_BIT_MSB	(CS42L42_PAGE_2A + 0x0F)
-#define CS42L42_ASP_RX_DAI1_CH1_BIT_LSB	(CS42L42_PAGE_2A + 0x10)
-#define CS42L42_ASP_RX_DAI1_CH2_AP_RES	(CS42L42_PAGE_2A + 0x11)
-#define CS42L42_ASP_RX_DAI1_CH2_BIT_MSB	(CS42L42_PAGE_2A + 0x12)
-#define CS42L42_ASP_RX_DAI1_CH2_BIT_LSB	(CS42L42_PAGE_2A + 0x13)
-
-#define CS42L42_ASP_RX_CH_AP_SHIFT	6
-#define CS42L42_ASP_RX_CH_AP_MASK	(1 << CS42L42_ASP_RX_CH_AP_SHIFT)
-#define CS42L42_ASP_RX_CH_AP_LOW	0
-#define CS42L42_ASP_RX_CH_AP_HI		1
-#define CS42L42_ASP_RX_CH_RES_SHIFT	0
-#define CS42L42_ASP_RX_CH_RES_MASK	(3 << CS42L42_ASP_RX_CH_RES_SHIFT)
-#define CS42L42_ASP_RX_CH_RES_32	3
-#define CS42L42_ASP_RX_CH_RES_16	1
-#define CS42L42_ASP_RX_CH_BIT_ST_SHIFT	0
-#define CS42L42_ASP_RX_CH_BIT_ST_MASK	(0xff << CS42L42_ASP_RX_CH_BIT_ST_SHIFT)
-
-/* Page 0x30 ID Registers */
-#define CS42L42_SUB_REVID		(CS42L42_PAGE_30 + 0x14)
-#define CS42L42_MAX_REGISTER		(CS42L42_PAGE_30 + 0x14)
-
-/* Defines for fracturing values spread across multiple registers */
-#define CS42L42_FRAC0_VAL(val)	((val) & 0x0000ff)
-#define CS42L42_FRAC1_VAL(val)	(((val) & 0x00ff00) >> 8)
-#define CS42L42_FRAC2_VAL(val)	(((val) & 0xff0000) >> 16)
-
-#define CS42L42_NUM_SUPPLIES	5
-#define CS42L42_BOOT_TIME_US	3000
-#define CS42L42_PLL_DIVOUT_TIME_US	800
-#define CS42L42_CLOCK_SWITCH_DELAY_US 150
-#define CS42L42_PLL_LOCK_POLL_US	250
-#define CS42L42_PLL_LOCK_TIMEOUT_US	1250
+#include <sound/cs42l42.h>
 
 static const char *const cs42l42_supply_names[CS42L42_NUM_SUPPLIES] = {
 	"VA",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l51-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l51-i2c.c
@@ -19,6 +19,12 @@
 };
 MODULE_DEVICE_TABLE(i2c, cs42l51_i2c_id);
 
+const struct of_device_id cs42l51_of_match[] = {
+	{ .compatible = "cirrus,cs42l51", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, cs42l51_of_match);
+
 static int cs42l51_i2c_probe(struct i2c_client *i2c,
 			     const struct i2c_device_id *id)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l51.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l51.c
@@ -754,8 +754,10 @@
 
 	cs42l51->reset_gpio = devm_gpiod_get_optional(dev, "reset",
 						      GPIOD_OUT_LOW);
-	if (IS_ERR(cs42l51->reset_gpio))
-		return PTR_ERR(cs42l51->reset_gpio);
+	if (IS_ERR(cs42l51->reset_gpio)) {
+		ret = PTR_ERR(cs42l51->reset_gpio);
+		goto error;
+	}
 
 	if (cs42l51->reset_gpio) {
 		dev_dbg(dev, "Release reset gpio\n");
@@ -787,6 +789,7 @@
 	return 0;
 
 error:
+	gpiod_set_value_cansleep(cs42l51->reset_gpio, 1);
 	regulator_bulk_disable(ARRAY_SIZE(cs42l51->supplies),
 			       cs42l51->supplies);
 	return ret;
@@ -825,13 +828,6 @@
 }
 EXPORT_SYMBOL_GPL(cs42l51_resume);
 
-const struct of_device_id cs42l51_of_match[] = {
-	{ .compatible = "cirrus,cs42l51", },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, cs42l51_of_match);
-EXPORT_SYMBOL_GPL(cs42l51_of_match);
-
 MODULE_AUTHOR("Arnaud Patard <arnaud.patard@rtp-net.org>");
 MODULE_DESCRIPTION("Cirrus Logic CS42L51 ALSA SoC Codec Driver");
 MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l51.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l51.h
@@ -16,7 +16,6 @@
 int cs42l51_remove(struct device *dev);
 int __maybe_unused cs42l51_suspend(struct device *dev);
 int __maybe_unused cs42l51_resume(struct device *dev);
-extern const struct of_device_id cs42l51_of_match[];
 
 #define CS42L51_CHIP_ID			0x1B
 #define CS42L51_CHIP_REV_A		0x00
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l52.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l52.c
@@ -137,7 +137,9 @@
 
 static DECLARE_TLV_DB_SCALE(pga_tlv, -600, 50, 0);
 
-static DECLARE_TLV_DB_SCALE(mix_tlv, -50, 50, 0);
+static DECLARE_TLV_DB_SCALE(pass_tlv, -6000, 50, 0);
+
+static DECLARE_TLV_DB_SCALE(mix_tlv, -5150, 50, 0);
 
 static DECLARE_TLV_DB_SCALE(beep_tlv, -56, 200, 0);
 
@@ -351,7 +353,7 @@
 			      CS42L52_SPKB_VOL, 0, 0x40, 0xC0, hl_tlv),
 
 	SOC_DOUBLE_R_SX_TLV("Bypass Volume", CS42L52_PASSTHRUA_VOL,
-			      CS42L52_PASSTHRUB_VOL, 0, 0x88, 0x90, pga_tlv),
+			      CS42L52_PASSTHRUB_VOL, 0, 0x88, 0x90, pass_tlv),
 
 	SOC_DOUBLE("Bypass Mute", CS42L52_MISC_CTL, 4, 5, 1, 0),
 
@@ -364,7 +366,7 @@
 			      CS42L52_ADCB_VOL, 0, 0xA0, 0x78, ipd_tlv),
 	SOC_DOUBLE_R_SX_TLV("ADC Mixer Volume",
 			     CS42L52_ADCA_MIXER_VOL, CS42L52_ADCB_MIXER_VOL,
-				0, 0x19, 0x7F, ipd_tlv),
+				0, 0x19, 0x7F, mix_tlv),
 
 	SOC_DOUBLE("ADC Switch", CS42L52_ADC_MISC_CTL, 0, 1, 1, 0),
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs42l56.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs42l56.c
@@ -391,9 +391,9 @@
 	SOC_DOUBLE("ADC Boost Switch", CS42L56_GAIN_BIAS_CTL, 3, 2, 1, 1),
 
 	SOC_DOUBLE_R_SX_TLV("Headphone Volume", CS42L56_HPA_VOLUME,
-			      CS42L56_HPB_VOLUME, 0, 0x84, 0x48, hl_tlv),
+			      CS42L56_HPB_VOLUME, 0, 0x44, 0x48, hl_tlv),
 	SOC_DOUBLE_R_SX_TLV("LineOut Volume", CS42L56_LOA_VOLUME,
-			      CS42L56_LOB_VOLUME, 0, 0x84, 0x48, hl_tlv),
+			      CS42L56_LOB_VOLUME, 0, 0x44, 0x48, hl_tlv),
 
 	SOC_SINGLE_TLV("Bass Shelving Volume", CS42L56_TONE_CTL,
 			0, 0x00, 1, tone_tlv),
@@ -1193,18 +1193,12 @@
 	if (pdata) {
 		cs42l56->pdata = *pdata;
 	} else {
-		pdata = devm_kzalloc(&i2c_client->dev, sizeof(*pdata),
-				     GFP_KERNEL);
-		if (!pdata)
-			return -ENOMEM;
-
 		if (i2c_client->dev.of_node) {
 			ret = cs42l56_handle_of_data(i2c_client,
 						     &cs42l56->pdata);
 			if (ret != 0)
 				return ret;
 		}
-		cs42l56->pdata = *pdata;
 	}
 
 	if (cs42l56->pdata.gpio_nreset) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs43130.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs43130.c
@@ -579,7 +579,7 @@
 		break;
 	case SND_SOC_DAIFMT_LEFT_J:
 		hi_size = bitwidth_sclk;
-		frm_delay = 2;
+		frm_delay = 0;
 		frm_phase = 1;
 		break;
 	case SND_SOC_DAIFMT_DSP_A:
@@ -1684,7 +1684,7 @@
 	return cs43130_show_dc(dev, buf, HP_RIGHT);
 }
 
-static u16 const cs43130_ac_freq[CS43130_AC_FREQ] = {
+static const u16 cs43130_ac_freq[CS43130_AC_FREQ] = {
 	24,
 	43,
 	93,
@@ -2365,7 +2365,7 @@
 	.use_single_write	= true,
 };
 
-static u16 const cs43130_dc_threshold[CS43130_DC_THRESHOLD] = {
+static const u16 cs43130_dc_threshold[CS43130_DC_THRESHOLD] = {
 	50,
 	120,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs47l15.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs47l15.c
@@ -122,6 +122,9 @@
 		snd_soc_kcontrol_component(kcontrol);
 	struct cs47l15 *cs47l15 = snd_soc_component_get_drvdata(component);
 
+	if (!!ucontrol->value.integer.value[0] == cs47l15->in1_lp_mode)
+		return 0;
+
 	switch (ucontrol->value.integer.value[0]) {
 	case 0:
 		/* Set IN1 to normal mode */
@@ -150,7 +153,7 @@
 		break;
 	}
 
-	return 0;
+	return 1;
 }
 
 static const struct snd_kcontrol_new cs47l15_snd_controls[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/cs53l30.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/cs53l30.c
@@ -348,22 +348,22 @@
 	SOC_ENUM("ADC2 NG Delay", adc2_ng_delay_enum),
 
 	SOC_SINGLE_SX_TLV("ADC1A PGA Volume",
-		    CS53L30_ADC1A_AFE_CTL, 0, 0x34, 0x18, pga_tlv),
+		    CS53L30_ADC1A_AFE_CTL, 0, 0x34, 0x24, pga_tlv),
 	SOC_SINGLE_SX_TLV("ADC1B PGA Volume",
-		    CS53L30_ADC1B_AFE_CTL, 0, 0x34, 0x18, pga_tlv),
+		    CS53L30_ADC1B_AFE_CTL, 0, 0x34, 0x24, pga_tlv),
 	SOC_SINGLE_SX_TLV("ADC2A PGA Volume",
-		    CS53L30_ADC2A_AFE_CTL, 0, 0x34, 0x18, pga_tlv),
+		    CS53L30_ADC2A_AFE_CTL, 0, 0x34, 0x24, pga_tlv),
 	SOC_SINGLE_SX_TLV("ADC2B PGA Volume",
-		    CS53L30_ADC2B_AFE_CTL, 0, 0x34, 0x18, pga_tlv),
+		    CS53L30_ADC2B_AFE_CTL, 0, 0x34, 0x24, pga_tlv),
 
 	SOC_SINGLE_SX_TLV("ADC1A Digital Volume",
-		    CS53L30_ADC1A_DIG_VOL, 0, 0xA0, 0x0C, dig_tlv),
+		    CS53L30_ADC1A_DIG_VOL, 0, 0xA0, 0x6C, dig_tlv),
 	SOC_SINGLE_SX_TLV("ADC1B Digital Volume",
-		    CS53L30_ADC1B_DIG_VOL, 0, 0xA0, 0x0C, dig_tlv),
+		    CS53L30_ADC1B_DIG_VOL, 0, 0xA0, 0x6C, dig_tlv),
 	SOC_SINGLE_SX_TLV("ADC2A Digital Volume",
-		    CS53L30_ADC2A_DIG_VOL, 0, 0xA0, 0x0C, dig_tlv),
+		    CS53L30_ADC2A_DIG_VOL, 0, 0xA0, 0x6C, dig_tlv),
 	SOC_SINGLE_SX_TLV("ADC2B Digital Volume",
-		    CS53L30_ADC2B_DIG_VOL, 0, 0xA0, 0x0C, dig_tlv),
+		    CS53L30_ADC2B_DIG_VOL, 0, 0xA0, 0x6C, dig_tlv),
 };
 
 static const struct snd_soc_dapm_widget cs53l30_dapm_widgets[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/da7210.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/da7210.c
@@ -1336,6 +1336,8 @@
 	int ret = 0;
 #if IS_ENABLED(CONFIG_I2C)
 	ret = i2c_add_driver(&da7210_i2c_driver);
+	if (ret)
+		return ret;
 #endif
 #if defined(CONFIG_SPI_MASTER)
 	ret = spi_register_driver(&da7210_spi_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/da7219-aad.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/da7219-aad.c
@@ -347,11 +347,15 @@
 	struct da7219_priv *da7219 = snd_soc_component_get_drvdata(component);
 	u8 events[DA7219_AAD_IRQ_REG_MAX];
 	u8 statusa;
-	int i, report = 0, mask = 0;
+	int i, ret, report = 0, mask = 0;
 
 	/* Read current IRQ events */
-	regmap_bulk_read(da7219->regmap, DA7219_ACCDET_IRQ_EVENT_A,
-			 events, DA7219_AAD_IRQ_REG_MAX);
+	ret = regmap_bulk_read(da7219->regmap, DA7219_ACCDET_IRQ_EVENT_A,
+			       events, DA7219_AAD_IRQ_REG_MAX);
+	if (ret) {
+		dev_warn_ratelimited(component->dev, "Failed to read IRQ events: %d\n", ret);
+		return IRQ_NONE;
+	}
 
 	if (!events[DA7219_AAD_IRQ_REG_A] && !events[DA7219_AAD_IRQ_REG_B])
 		return IRQ_NONE;
@@ -625,8 +629,10 @@
 		return NULL;
 
 	aad_pdata = devm_kzalloc(dev, sizeof(*aad_pdata), GFP_KERNEL);
-	if (!aad_pdata)
+	if (!aad_pdata) {
+		fwnode_handle_put(aad_np);
 		return NULL;
+	}
 
 	aad_pdata->irq = i2c->irq;
 
@@ -650,7 +656,7 @@
 		aad_pdata->mic_det_thr =
 			da7219_aad_fw_mic_det_thr(dev, fw_val32);
 	else
-		aad_pdata->mic_det_thr = DA7219_AAD_MIC_DET_THR_500_OHMS;
+		aad_pdata->mic_det_thr = DA7219_AAD_MIC_DET_THR_200_OHMS;
 
 	if (fwnode_property_read_u32(aad_np, "dlg,jack-ins-deb", &fw_val32) >= 0)
 		aad_pdata->jack_ins_deb =
@@ -701,6 +707,8 @@
 	else
 		aad_pdata->adc_1bit_rpt = DA7219_AAD_ADC_1BIT_RPT_1;
 
+	fwnode_handle_put(aad_np);
+
 	return aad_pdata;
 }
 
@@ -854,6 +862,8 @@
 			}
 		}
 	}
+
+	synchronize_irq(da7219_aad->irq);
 }
 
 void da7219_aad_resume(struct snd_soc_component *component)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/da7219.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/da7219.c
@@ -446,7 +446,7 @@
 	struct soc_mixer_control *mixer_ctrl =
 		(struct soc_mixer_control *) kcontrol->private_value;
 	unsigned int reg = mixer_ctrl->reg;
-	__le16 val;
+	__le16 val_new, val_old;
 	int ret;
 
 	/*
@@ -454,13 +454,19 @@
 	 * Therefore we need to convert to little endian here to align with
 	 * HW registers.
 	 */
-	val = cpu_to_le16(ucontrol->value.integer.value[0]);
+	val_new = cpu_to_le16(ucontrol->value.integer.value[0]);
 
 	mutex_lock(&da7219->ctrl_lock);
-	ret = regmap_raw_write(da7219->regmap, reg, &val, sizeof(val));
+	ret = regmap_raw_read(da7219->regmap, reg, &val_old, sizeof(val_old));
+	if (ret == 0 && (val_old != val_new))
+		ret = regmap_raw_write(da7219->regmap, reg,
+				&val_new, sizeof(val_new));
 	mutex_unlock(&da7219->ctrl_lock);
 
-	return ret;
+	if (ret < 0)
+		return ret;
+
+	return val_old != val_new;
 }
 
 
@@ -1161,17 +1167,20 @@
 	struct da7219_priv *da7219 = snd_soc_component_get_drvdata(component);
 	int ret = 0;
 
-	if ((da7219->clk_src == clk_id) && (da7219->mclk_rate == freq))
+	mutex_lock(&da7219->pll_lock);
+
+	if ((da7219->clk_src == clk_id) && (da7219->mclk_rate == freq)) {
+		mutex_unlock(&da7219->pll_lock);
 		return 0;
+	}
 
 	if ((freq < 2000000) || (freq > 54000000)) {
+		mutex_unlock(&da7219->pll_lock);
 		dev_err(codec_dai->dev, "Unsupported MCLK value %d\n",
 			freq);
 		return -EINVAL;
 	}
 
-	mutex_lock(&da7219->pll_lock);
-
 	switch (clk_id) {
 	case DA7219_CLKSRC_MCLK_SQR:
 		snd_soc_component_update_bits(component, DA7219_PLL_CTRL,
@@ -2190,6 +2199,7 @@
 			dai_clk_lookup = clkdev_hw_create(dai_clk_hw, init.name,
 							  "%s", dev_name(dev));
 			if (!dai_clk_lookup) {
+				clk_hw_unregister(dai_clk_hw);
 				ret = -ENOMEM;
 				goto err;
 			} else {
@@ -2211,12 +2221,12 @@
 	return 0;
 
 err:
-	do {
+	while (--i >= 0) {
 		if (da7219->dai_clks_lookup[i])
 			clkdev_drop(da7219->dai_clks_lookup[i]);
 
 		clk_hw_unregister(&da7219->dai_clks_hw[i]);
-	} while (i-- > 0);
+	}
 
 	if (np)
 		kfree(da7219->clk_hw_data);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/es8316.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/es8316.c
@@ -52,7 +52,12 @@
 static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(adc_vol_tlv, -9600, 50, 1);
 static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(alc_max_gain_tlv, -650, 150, 0);
 static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(alc_min_gain_tlv, -1200, 150, 0);
-static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(alc_target_tlv, -1650, 150, 0);
+
+static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(alc_target_tlv,
+	0, 10, TLV_DB_SCALE_ITEM(-1650, 150, 0),
+	11, 11, TLV_DB_SCALE_ITEM(-150, 0, 0),
+);
+
 static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(hpmixer_gain_tlv,
 	0, 4, TLV_DB_SCALE_ITEM(-1200, 150, 0),
 	8, 11, TLV_DB_SCALE_ITEM(-450, 150, 0),
@@ -115,7 +120,7 @@
 		       alc_max_gain_tlv),
 	SOC_SINGLE_TLV("ALC Capture Min Volume", ES8316_ADC_ALC2, 0, 28, 0,
 		       alc_min_gain_tlv),
-	SOC_SINGLE_TLV("ALC Capture Target Volume", ES8316_ADC_ALC3, 4, 10, 0,
+	SOC_SINGLE_TLV("ALC Capture Target Volume", ES8316_ADC_ALC3, 4, 11, 0,
 		       alc_target_tlv),
 	SOC_SINGLE("ALC Capture Hold Time", ES8316_ADC_ALC3, 0, 10, 0),
 	SOC_SINGLE("ALC Capture Decay Time", ES8316_ADC_ALC4, 4, 10, 0),
@@ -148,7 +153,7 @@
 		"dmic data at high level",
 		"dmic data at low level",
 };
-static const unsigned int es8316_dmic_values[] = { 0, 1, 2 };
+static const unsigned int es8316_dmic_values[] = { 0, 2, 3 };
 static const struct soc_enum es8316_dmic_src_enum =
 	SOC_VALUE_ENUM_SINGLE(ES8316_ADC_DMIC, 0, 3,
 			      ARRAY_SIZE(es8316_dmic_txt),
@@ -364,13 +369,11 @@
 	int count = 0;
 
 	es8316->sysclk = freq;
+	es8316->sysclk_constraints.list = NULL;
+	es8316->sysclk_constraints.count = 0;
 
-	if (freq == 0) {
-		es8316->sysclk_constraints.list = NULL;
-		es8316->sysclk_constraints.count = 0;
-
+	if (freq == 0)
 		return 0;
-	}
 
 	ret = clk_set_rate(es8316->mclk, freq);
 	if (ret)
@@ -386,8 +389,10 @@
 			es8316->allowed_rates[count++] = freq / ratio;
 	}
 
-	es8316->sysclk_constraints.list = es8316->allowed_rates;
-	es8316->sysclk_constraints.count = count;
+	if (count) {
+		es8316->sysclk_constraints.list = es8316->allowed_rates;
+		es8316->sysclk_constraints.count = count;
+	}
 
 	return 0;
 }
@@ -810,15 +815,14 @@
 	es8316->irq = i2c_client->irq;
 	mutex_init(&es8316->lock);
 
-	ret = devm_request_threaded_irq(dev, es8316->irq, NULL, es8316_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
-					"es8316", es8316);
-	if (ret == 0) {
-		/* Gets re-enabled by es8316_set_jack() */
-		disable_irq(es8316->irq);
-	} else {
-		dev_warn(dev, "Failed to get IRQ %d: %d\n", es8316->irq, ret);
-		es8316->irq = -ENXIO;
+	if (es8316->irq > 0) {
+		ret = devm_request_threaded_irq(dev, es8316->irq, NULL, es8316_irq,
+						IRQF_TRIGGER_HIGH | IRQF_ONESHOT | IRQF_NO_AUTOEN,
+						"es8316", es8316);
+		if (ret) {
+			dev_warn(dev, "Failed to get IRQ %d: %d\n", es8316->irq, ret);
+			es8316->irq = -ENXIO;
+		}
 	}
 
 	return devm_snd_soc_register_component(&i2c_client->dev,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/es8328.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/es8328.c
@@ -161,13 +161,16 @@
 	if (deemph > 1)
 		return -EINVAL;
 
+	if (es8328->deemph == deemph)
+		return 0;
+
 	ret = es8328_set_deemph(component);
 	if (ret < 0)
 		return ret;
 
 	es8328->deemph = deemph;
 
-	return 0;
+	return 1;
 }
 
 
@@ -231,7 +234,6 @@
 
 /* Left Mixer */
 static const struct snd_kcontrol_new es8328_left_mixer_controls[] = {
-	SOC_DAPM_SINGLE("Playback Switch", ES8328_DACCONTROL17, 7, 1, 0),
 	SOC_DAPM_SINGLE("Left Bypass Switch", ES8328_DACCONTROL17, 6, 1, 0),
 	SOC_DAPM_SINGLE("Right Playback Switch", ES8328_DACCONTROL18, 7, 1, 0),
 	SOC_DAPM_SINGLE("Right Bypass Switch", ES8328_DACCONTROL18, 6, 1, 0),
@@ -241,7 +243,6 @@
 static const struct snd_kcontrol_new es8328_right_mixer_controls[] = {
 	SOC_DAPM_SINGLE("Left Playback Switch", ES8328_DACCONTROL19, 7, 1, 0),
 	SOC_DAPM_SINGLE("Left Bypass Switch", ES8328_DACCONTROL19, 6, 1, 0),
-	SOC_DAPM_SINGLE("Playback Switch", ES8328_DACCONTROL20, 7, 1, 0),
 	SOC_DAPM_SINGLE("Right Bypass Switch", ES8328_DACCONTROL20, 6, 1, 0),
 };
 
@@ -334,10 +335,10 @@
 	SND_SOC_DAPM_DAC("Left DAC", "Left Playback", ES8328_DACPOWER,
 			ES8328_DACPOWER_LDAC_OFF, 1),
 
-	SND_SOC_DAPM_MIXER("Left Mixer", SND_SOC_NOPM, 0, 0,
+	SND_SOC_DAPM_MIXER("Left Mixer", ES8328_DACCONTROL17, 7, 0,
 		&es8328_left_mixer_controls[0],
 		ARRAY_SIZE(es8328_left_mixer_controls)),
-	SND_SOC_DAPM_MIXER("Right Mixer", SND_SOC_NOPM, 0, 0,
+	SND_SOC_DAPM_MIXER("Right Mixer", ES8328_DACCONTROL20, 7, 0,
 		&es8328_right_mixer_controls[0],
 		ARRAY_SIZE(es8328_right_mixer_controls)),
 
@@ -416,19 +417,14 @@
 	{ "Right Line Mux", "PGA", "Right PGA Mux" },
 	{ "Right Line Mux", "Differential", "Differential Mux" },
 
-	{ "Left Out 1", NULL, "Left DAC" },
-	{ "Right Out 1", NULL, "Right DAC" },
-	{ "Left Out 2", NULL, "Left DAC" },
-	{ "Right Out 2", NULL, "Right DAC" },
-
-	{ "Left Mixer", "Playback Switch", "Left DAC" },
+	{ "Left Mixer", NULL, "Left DAC" },
 	{ "Left Mixer", "Left Bypass Switch", "Left Line Mux" },
 	{ "Left Mixer", "Right Playback Switch", "Right DAC" },
 	{ "Left Mixer", "Right Bypass Switch", "Right Line Mux" },
 
 	{ "Right Mixer", "Left Playback Switch", "Left DAC" },
 	{ "Right Mixer", "Left Bypass Switch", "Left Line Mux" },
-	{ "Right Mixer", "Playback Switch", "Right DAC" },
+	{ "Right Mixer", NULL, "Right DAC" },
 	{ "Right Mixer", "Right Bypass Switch", "Right Line Mux" },
 
 	{ "DAC DIG", NULL, "DAC STM" },
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/hdac_hda.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/hdac_hda.c
@@ -46,9 +46,8 @@
 				  struct snd_soc_dai *dai);
 static int hdac_hda_dai_hw_free(struct snd_pcm_substream *substream,
 				struct snd_soc_dai *dai);
-static int hdac_hda_dai_set_tdm_slot(struct snd_soc_dai *dai,
-				     unsigned int tx_mask, unsigned int rx_mask,
-				     int slots, int slot_width);
+static int hdac_hda_dai_set_stream(struct snd_soc_dai *dai, void *stream,
+				   int direction);
 static struct hda_pcm *snd_soc_find_pcm_from_dai(struct hdac_hda_priv *hda_pvt,
 						 struct snd_soc_dai *dai);
 
@@ -58,7 +57,7 @@
 	.prepare = hdac_hda_dai_prepare,
 	.hw_params = hdac_hda_dai_hw_params,
 	.hw_free = hdac_hda_dai_hw_free,
-	.set_tdm_slot = hdac_hda_dai_set_tdm_slot,
+	.set_stream = hdac_hda_dai_set_stream,
 };
 
 static struct snd_soc_dai_driver hdac_hda_dais[] = {
@@ -180,21 +179,22 @@
 
 };
 
-static int hdac_hda_dai_set_tdm_slot(struct snd_soc_dai *dai,
-				     unsigned int tx_mask, unsigned int rx_mask,
-				     int slots, int slot_width)
+static int hdac_hda_dai_set_stream(struct snd_soc_dai *dai,
+				   void *stream, int direction)
 {
 	struct snd_soc_component *component = dai->component;
 	struct hdac_hda_priv *hda_pvt;
 	struct hdac_hda_pcm *pcm;
+	struct hdac_stream *hstream;
+
+	if (!stream)
+		return -EINVAL;
 
 	hda_pvt = snd_soc_component_get_drvdata(component);
 	pcm = &hda_pvt->pcm[dai->id];
+	hstream = (struct hdac_stream *)stream;
 
-	if (tx_mask)
-		pcm->stream_tag[SNDRV_PCM_STREAM_PLAYBACK] = tx_mask;
-	else
-		pcm->stream_tag[SNDRV_PCM_STREAM_CAPTURE] = rx_mask;
+	pcm->stream_tag[direction] = hstream->stream_tag;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/hdac_hda.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/hdac_hda.h
@@ -14,7 +14,7 @@
 	HDAC_HDMI_1_DAI_ID,
 	HDAC_HDMI_2_DAI_ID,
 	HDAC_HDMI_3_DAI_ID,
-	HDAC_LAST_DAI_ID = HDAC_HDMI_3_DAI_ID,
+	HDAC_DAI_ID_NUM
 };
 
 struct hdac_hda_pcm {
@@ -24,7 +24,7 @@
 
 struct hdac_hda_priv {
 	struct hda_codec codec;
-	struct hdac_hda_pcm pcm[HDAC_LAST_DAI_ID];
+	struct hdac_hda_pcm pcm[HDAC_DAI_ID_NUM];
 	bool need_display_power;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/hdac_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/hdac_hdmi.c
@@ -436,23 +436,28 @@
 	return 0;
 }
 
-static int hdac_hdmi_set_tdm_slot(struct snd_soc_dai *dai,
-		unsigned int tx_mask, unsigned int rx_mask,
-		int slots, int slot_width)
+static int hdac_hdmi_set_stream(struct snd_soc_dai *dai,
+				void *stream, int direction)
 {
 	struct hdac_hdmi_priv *hdmi = snd_soc_dai_get_drvdata(dai);
 	struct hdac_device *hdev = hdmi->hdev;
 	struct hdac_hdmi_dai_port_map *dai_map;
 	struct hdac_hdmi_pcm *pcm;
+	struct hdac_stream *hstream;
 
-	dev_dbg(&hdev->dev, "%s: strm_tag: %d\n", __func__, tx_mask);
+	if (!stream)
+		return -EINVAL;
+
+	hstream = (struct hdac_stream *)stream;
+
+	dev_dbg(&hdev->dev, "%s: strm_tag: %d\n", __func__, hstream->stream_tag);
 
 	dai_map = &hdmi->dai_map[dai->id];
 
 	pcm = hdac_hdmi_get_pcm_from_cvt(hdmi, dai_map->cvt);
 
 	if (pcm)
-		pcm->stream_tag = (tx_mask << 4);
+		pcm->stream_tag = (hstream->stream_tag << 4);
 
 	return 0;
 }
@@ -1544,7 +1549,7 @@
 	.startup = hdac_hdmi_pcm_open,
 	.shutdown = hdac_hdmi_pcm_close,
 	.hw_params = hdac_hdmi_set_hw_params,
-	.set_tdm_slot = hdac_hdmi_set_tdm_slot,
+	.set_stream = hdac_hdmi_set_stream,
 };
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/hdmi-codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/hdmi-codec.c
@@ -188,84 +188,97 @@
 /*
  * hdmi_codec_channel_alloc: speaker configuration available for CEA
  *
- * This is an ordered list that must match with hdmi_codec_8ch_chmaps struct
+ * This is an ordered list where ca_id must exist in hdmi_codec_8ch_chmaps
  * The preceding ones have better chances to be selected by
  * hdmi_codec_get_ch_alloc_table_idx().
  */
 static const struct hdmi_codec_cea_spk_alloc hdmi_codec_channel_alloc[] = {
 	{ .ca_id = 0x00, .n_ch = 2,
-	  .mask = FL | FR},
-	/* 2.1 */
-	{ .ca_id = 0x01, .n_ch = 4,
-	  .mask = FL | FR | LFE},
-	/* Dolby Surround */
+	  .mask = FL | FR },
+	{ .ca_id = 0x03, .n_ch = 4,
+	  .mask = FL | FR | LFE | FC },
 	{ .ca_id = 0x02, .n_ch = 4,
 	  .mask = FL | FR | FC },
-	/* surround51 */
+	{ .ca_id = 0x01, .n_ch = 4,
+	  .mask = FL | FR | LFE },
 	{ .ca_id = 0x0b, .n_ch = 6,
-	  .mask = FL | FR | LFE | FC | RL | RR},
-	/* surround40 */
-	{ .ca_id = 0x08, .n_ch = 6,
-	  .mask = FL | FR | RL | RR },
-	/* surround41 */
-	{ .ca_id = 0x09, .n_ch = 6,
-	  .mask = FL | FR | LFE | RL | RR },
-	/* surround50 */
+	  .mask = FL | FR | LFE | FC | RL | RR },
 	{ .ca_id = 0x0a, .n_ch = 6,
 	  .mask = FL | FR | FC | RL | RR },
-	/* 6.1 */
-	{ .ca_id = 0x0f, .n_ch = 8,
-	  .mask = FL | FR | LFE | FC | RL | RR | RC },
-	/* surround71 */
+	{ .ca_id = 0x09, .n_ch = 6,
+	  .mask = FL | FR | LFE | RL | RR },
+	{ .ca_id = 0x08, .n_ch = 6,
+	  .mask = FL | FR | RL | RR },
+	{ .ca_id = 0x07, .n_ch = 6,
+	  .mask = FL | FR | LFE | FC | RC },
+	{ .ca_id = 0x06, .n_ch = 6,
+	  .mask = FL | FR | FC | RC },
+	{ .ca_id = 0x05, .n_ch = 6,
+	  .mask = FL | FR | LFE | RC },
+	{ .ca_id = 0x04, .n_ch = 6,
+	  .mask = FL | FR | RC },
 	{ .ca_id = 0x13, .n_ch = 8,
 	  .mask = FL | FR | LFE | FC | RL | RR | RLC | RRC },
-	/* others */
-	{ .ca_id = 0x03, .n_ch = 8,
-	  .mask = FL | FR | LFE | FC },
-	{ .ca_id = 0x04, .n_ch = 8,
-	  .mask = FL | FR | RC},
-	{ .ca_id = 0x05, .n_ch = 8,
-	  .mask = FL | FR | LFE | RC },
-	{ .ca_id = 0x06, .n_ch = 8,
-	  .mask = FL | FR | FC | RC },
-	{ .ca_id = 0x07, .n_ch = 8,
-	  .mask = FL | FR | LFE | FC | RC },
-	{ .ca_id = 0x0c, .n_ch = 8,
-	  .mask = FL | FR | RC | RL | RR },
-	{ .ca_id = 0x0d, .n_ch = 8,
-	  .mask = FL | FR | LFE | RL | RR | RC },
-	{ .ca_id = 0x0e, .n_ch = 8,
-	  .mask = FL | FR | FC | RL | RR | RC },
-	{ .ca_id = 0x10, .n_ch = 8,
-	  .mask = FL | FR | RL | RR | RLC | RRC },
-	{ .ca_id = 0x11, .n_ch = 8,
-	  .mask = FL | FR | LFE | RL | RR | RLC | RRC },
+	{ .ca_id = 0x1f, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | FLC | FRC },
 	{ .ca_id = 0x12, .n_ch = 8,
 	  .mask = FL | FR | FC | RL | RR | RLC | RRC },
-	{ .ca_id = 0x14, .n_ch = 8,
-	  .mask = FL | FR | FLC | FRC },
-	{ .ca_id = 0x15, .n_ch = 8,
-	  .mask = FL | FR | LFE | FLC | FRC },
-	{ .ca_id = 0x16, .n_ch = 8,
-	  .mask = FL | FR | FC | FLC | FRC },
-	{ .ca_id = 0x17, .n_ch = 8,
-	  .mask = FL | FR | LFE | FC | FLC | FRC },
-	{ .ca_id = 0x18, .n_ch = 8,
-	  .mask = FL | FR | RC | FLC | FRC },
-	{ .ca_id = 0x19, .n_ch = 8,
-	  .mask = FL | FR | LFE | RC | FLC | FRC },
-	{ .ca_id = 0x1a, .n_ch = 8,
-	  .mask = FL | FR | RC | FC | FLC | FRC },
-	{ .ca_id = 0x1b, .n_ch = 8,
-	  .mask = FL | FR | LFE | RC | FC | FLC | FRC },
-	{ .ca_id = 0x1c, .n_ch = 8,
-	  .mask = FL | FR | RL | RR | FLC | FRC },
-	{ .ca_id = 0x1d, .n_ch = 8,
-	  .mask = FL | FR | LFE | RL | RR | FLC | FRC },
 	{ .ca_id = 0x1e, .n_ch = 8,
 	  .mask = FL | FR | FC | RL | RR | FLC | FRC },
-	{ .ca_id = 0x1f, .n_ch = 8,
-	  .mask = FL | FR | LFE | FC | RL | RR | FLC | FRC },
+	{ .ca_id = 0x11, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | RLC | RRC },
+	{ .ca_id = 0x1d, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | FLC | FRC },
+	{ .ca_id = 0x10, .n_ch = 8,
+	  .mask = FL | FR | RL | RR | RLC | RRC },
+	{ .ca_id = 0x1c, .n_ch = 8,
+	  .mask = FL | FR | RL | RR | FLC | FRC },
+	{ .ca_id = 0x0f, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | RC },
+	{ .ca_id = 0x1b, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC | FC | FLC | FRC },
+	{ .ca_id = 0x0e, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | RC },
+	{ .ca_id = 0x1a, .n_ch = 8,
+	  .mask = FL | FR | RC | FC | FLC | FRC },
+	{ .ca_id = 0x0d, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | RC },
+	{ .ca_id = 0x19, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC | FLC | FRC },
+	{ .ca_id = 0x0c, .n_ch = 8,
+	  .mask = FL | FR | RC | RL | RR },
+	{ .ca_id = 0x18, .n_ch = 8,
+	  .mask = FL | FR | RC | FLC | FRC },
+	{ .ca_id = 0x17, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | FLC | FRC },
+	{ .ca_id = 0x16, .n_ch = 8,
+	  .mask = FL | FR | FC | FLC | FRC },
+	{ .ca_id = 0x15, .n_ch = 8,
+	  .mask = FL | FR | LFE | FLC | FRC },
+	{ .ca_id = 0x14, .n_ch = 8,
+	  .mask = FL | FR | FLC | FRC },
+	{ .ca_id = 0x0b, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR },
+	{ .ca_id = 0x0a, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR },
+	{ .ca_id = 0x09, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR },
+	{ .ca_id = 0x08, .n_ch = 8,
+	  .mask = FL | FR | RL | RR },
+	{ .ca_id = 0x07, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RC },
+	{ .ca_id = 0x06, .n_ch = 8,
+	  .mask = FL | FR | FC | RC },
+	{ .ca_id = 0x05, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC },
+	{ .ca_id = 0x04, .n_ch = 8,
+	  .mask = FL | FR | RC },
+	{ .ca_id = 0x03, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC },
+	{ .ca_id = 0x02, .n_ch = 8,
+	  .mask = FL | FR | FC },
+	{ .ca_id = 0x01, .n_ch = 8,
+	  .mask = FL | FR | LFE },
 };
 
 struct hdmi_codec_priv {
@@ -277,7 +290,7 @@
 	bool busy;
 	struct snd_soc_jack *jack;
 	unsigned int jack_status;
-	u8 iec_status[5];
+	u8 iec_status[AES_IEC958_STATUS_SIZE];
 };
 
 static const struct snd_soc_dapm_widget hdmi_widgets[] = {
@@ -374,7 +387,8 @@
 	struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
 	struct hdmi_codec_priv *hcp = info->private_data;
 
-	map = info->chmap[hcp->chmap_idx].map;
+	if (hcp->chmap_idx != HDMI_CODEC_CHMAP_IDX_UNKNOWN)
+		map = info->chmap[hcp->chmap_idx].map;
 
 	for (i = 0; i < info->max_channels; i++) {
 		if (hcp->chmap_idx == HDMI_CODEC_CHMAP_IDX_UNKNOWN)
@@ -843,8 +857,9 @@
 static void hdmi_codec_jack_report(struct hdmi_codec_priv *hcp,
 				   unsigned int jack_status)
 {
-	if (hcp->jack && jack_status != hcp->jack_status) {
-		snd_soc_jack_report(hcp->jack, jack_status, SND_JACK_LINEOUT);
+	if (jack_status != hcp->jack_status) {
+		if (hcp->jack)
+			snd_soc_jack_report(hcp->jack, jack_status, SND_JACK_LINEOUT);
 		hcp->jack_status = jack_status;
 	}
 }
@@ -870,18 +885,20 @@
 			       void *data)
 {
 	struct hdmi_codec_priv *hcp = snd_soc_component_get_drvdata(component);
-	int ret = -ENOTSUPP;
 
 	if (hcp->hcd.ops->hook_plugged_cb) {
 		hcp->jack = jack;
-		ret = hcp->hcd.ops->hook_plugged_cb(component->dev->parent,
-						    hcp->hcd.data,
-						    plugged_cb,
-						    component->dev);
-		if (ret)
-			hcp->jack = NULL;
+
+		/*
+		 * Report the initial jack status which may have been provided
+		 * by the parent hdmi driver while the hpd hook was registered.
+		 */
+		snd_soc_jack_report(jack, hcp->jack_status, SND_JACK_LINEOUT);
+
+		return 0;
 	}
-	return ret;
+
+	return -ENOTSUPP;
 }
 
 static int hdmi_dai_spdif_probe(struct snd_soc_dai *dai)
@@ -965,6 +982,21 @@
 	return ret;
 }
 
+static int hdmi_probe(struct snd_soc_component *component)
+{
+	struct hdmi_codec_priv *hcp = snd_soc_component_get_drvdata(component);
+	int ret = 0;
+
+	if (hcp->hcd.ops->hook_plugged_cb) {
+		ret = hcp->hcd.ops->hook_plugged_cb(component->dev->parent,
+						    hcp->hcd.data,
+						    plugged_cb,
+						    component->dev);
+	}
+
+	return ret;
+}
+
 static void hdmi_remove(struct snd_soc_component *component)
 {
 	struct hdmi_codec_priv *hcp = snd_soc_component_get_drvdata(component);
@@ -975,6 +1007,7 @@
 }
 
 static const struct snd_soc_component_driver hdmi_driver = {
+	.probe			= hdmi_probe,
 	.remove			= hdmi_remove,
 	.dapm_widgets		= hdmi_widgets,
 	.num_dapm_widgets	= ARRAY_SIZE(hdmi_widgets),
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/jz4725b.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/jz4725b.c
@@ -136,14 +136,17 @@
 #define REG_CGR3_GO1L_OFFSET		0
 #define REG_CGR3_GO1L_MASK		(0x1f << REG_CGR3_GO1L_OFFSET)
 
+#define REG_CGR10_GIL_OFFSET		0
+#define REG_CGR10_GIR_OFFSET		4
+
 struct jz_icdc {
 	struct regmap *regmap;
 	void __iomem *base;
 	struct clk *clk;
 };
 
-static const SNDRV_CTL_TLVD_DECLARE_DB_LINEAR(jz4725b_dac_tlv, -2250, 0);
-static const SNDRV_CTL_TLVD_DECLARE_DB_LINEAR(jz4725b_line_tlv, -1500, 600);
+static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(jz4725b_adc_tlv,     0, 150, 0);
+static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(jz4725b_dac_tlv, -2250, 150, 0);
 
 static const struct snd_kcontrol_new jz4725b_codec_controls[] = {
 	SOC_DOUBLE_TLV("Master Playback Volume",
@@ -151,11 +154,11 @@
 		       REG_CGR1_GODL_OFFSET,
 		       REG_CGR1_GODR_OFFSET,
 		       0xf, 1, jz4725b_dac_tlv),
-	SOC_DOUBLE_R_TLV("Master Capture Volume",
-			 JZ4725B_CODEC_REG_CGR3,
-			 JZ4725B_CODEC_REG_CGR2,
-			 REG_CGR2_GO1R_OFFSET,
-			 0x1f, 1, jz4725b_line_tlv),
+	SOC_DOUBLE_TLV("Master Capture Volume",
+		       JZ4725B_CODEC_REG_CGR10,
+		       REG_CGR10_GIL_OFFSET,
+		       REG_CGR10_GIR_OFFSET,
+		       0xf, 0, jz4725b_adc_tlv),
 
 	SOC_SINGLE("Master Playback Switch", JZ4725B_CODEC_REG_CR1,
 		   REG_CR1_DAC_MUTE_OFFSET, 1, 1),
@@ -180,7 +183,7 @@
 				  jz4725b_codec_adc_src_texts,
 				  jz4725b_codec_adc_src_values);
 static const struct snd_kcontrol_new jz4725b_codec_adc_src_ctrl =
-			SOC_DAPM_ENUM("Route", jz4725b_codec_adc_src_enum);
+	SOC_DAPM_ENUM("ADC Source Capture Route", jz4725b_codec_adc_src_enum);
 
 static const struct snd_kcontrol_new jz4725b_codec_mixer_controls[] = {
 	SOC_DAPM_SINGLE("Line In Bypass", JZ4725B_CODEC_REG_CR1,
@@ -225,7 +228,7 @@
 	SND_SOC_DAPM_ADC("ADC", "Capture",
 			 JZ4725B_CODEC_REG_PMR1, REG_PMR1_SB_ADC_OFFSET, 1),
 
-	SND_SOC_DAPM_MUX("ADC Source", SND_SOC_NOPM, 0, 0,
+	SND_SOC_DAPM_MUX("ADC Source Capture Route", SND_SOC_NOPM, 0, 0,
 			 &jz4725b_codec_adc_src_ctrl),
 
 	/* Mixer */
@@ -236,7 +239,8 @@
 	SND_SOC_DAPM_MIXER("DAC to Mixer", JZ4725B_CODEC_REG_CR1,
 			   REG_CR1_DACSEL_OFFSET, 0, NULL, 0),
 
-	SND_SOC_DAPM_MIXER("Line In", SND_SOC_NOPM, 0, 0, NULL, 0),
+	SND_SOC_DAPM_MIXER("Line In", JZ4725B_CODEC_REG_PMR1,
+			   REG_PMR1_SB_LIN_OFFSET, 1, NULL, 0),
 	SND_SOC_DAPM_MIXER("HP Out", JZ4725B_CODEC_REG_CR1,
 			   REG_CR1_HP_DIS_OFFSET, 1, NULL, 0),
 
@@ -283,11 +287,11 @@
 	{"Mixer", NULL, "DAC to Mixer"},
 
 	{"Mixer to ADC", NULL, "Mixer"},
-	{"ADC Source", "Mixer", "Mixer to ADC"},
-	{"ADC Source", "Line In", "Line In"},
-	{"ADC Source", "Mic 1", "Mic 1"},
-	{"ADC Source", "Mic 2", "Mic 2"},
-	{"ADC", NULL, "ADC Source"},
+	{"ADC Source Capture Route", "Mixer", "Mixer to ADC"},
+	{"ADC Source Capture Route", "Line In", "Line In"},
+	{"ADC Source Capture Route", "Mic 1", "Mic 1"},
+	{"ADC Source Capture Route", "Mic 2", "Mic 2"},
+	{"ADC", NULL, "ADC Source Capture Route"},
 
 	{"Out Stage", NULL, "Mixer"},
 	{"HP Out", NULL, "Out Stage"},
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/lpass-rx-macro.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/lpass-rx-macro.c
@@ -363,7 +363,7 @@
 #define CDC_RX_DSD1_CFG2			(0x0F8C)
 #define RX_MAX_OFFSET				(0x0F8C)
 
-#define MCLK_FREQ		9600000
+#define MCLK_FREQ		19200000
 
 #define RX_MACRO_RATES (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\
 			SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_48000 |\
@@ -608,7 +608,11 @@
 	int softclip_clk_users;
 
 	struct regmap *regmap;
-	struct clk_bulk_data clks[RX_NUM_CLKS_MAX];
+	struct clk *mclk;
+	struct clk *npl;
+	struct clk *macro;
+	struct clk *dcodec;
+	struct clk *fsgen;
 	struct clk_hw hw;
 };
 #define to_rx_macro(_hw) container_of(_hw, struct rx_macro, hw)
@@ -903,7 +907,7 @@
 	{ CDC_RX_BCL_VBAT_PK_EST2, 0x01 },
 	{ CDC_RX_BCL_VBAT_PK_EST3, 0x40 },
 	{ CDC_RX_BCL_VBAT_RF_PROC1, 0x2A },
-	{ CDC_RX_BCL_VBAT_RF_PROC1, 0x00 },
+	{ CDC_RX_BCL_VBAT_RF_PROC2, 0x00 },
 	{ CDC_RX_BCL_VBAT_TAC1, 0x00 },
 	{ CDC_RX_BCL_VBAT_TAC2, 0x18 },
 	{ CDC_RX_BCL_VBAT_TAC3, 0x18 },
@@ -2039,6 +2043,10 @@
 	int i;
 	int hph_pwr_mode;
 
+	/* AUX does not have compander */
+	if (comp == INTERP_AUX)
+		return 0;
+
 	if (!rx->comp_enabled[comp])
 		return 0;
 
@@ -2188,7 +2196,7 @@
 		snd_soc_component_update_bits(component,
 				CDC_RX_CLSH_DECAY_CTRL,
 				CDC_RX_CLSH_DECAY_RATE_MASK, 0x0);
-		snd_soc_component_update_bits(component,
+		snd_soc_component_write_field(component,
 				CDC_RX_RX1_RX_PATH_CFG0,
 				CDC_RX_RXn_CLSH_EN_MASK, 0x1);
 		break;
@@ -2268,7 +2276,7 @@
 	struct snd_soc_component *component = snd_soc_dapm_to_component(widget->dapm);
 	struct rx_macro *rx = snd_soc_component_get_drvdata(component);
 
-	ucontrol->value.integer.value[0] =
+	ucontrol->value.enumerated.item[0] =
 			rx->rx_port_value[widget->shift];
 	return 0;
 }
@@ -2280,7 +2288,7 @@
 	struct snd_soc_component *component = snd_soc_dapm_to_component(widget->dapm);
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	struct snd_soc_dapm_update *update = NULL;
-	u32 rx_port_value = ucontrol->value.integer.value[0];
+	u32 rx_port_value = ucontrol->value.enumerated.item[0];
 	u32 aif_rst;
 	struct rx_macro *rx = snd_soc_component_get_drvdata(component);
 
@@ -2392,7 +2400,7 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct rx_macro *rx = snd_soc_component_get_drvdata(component);
 
-	ucontrol->value.integer.value[0] = rx->hph_pwr_mode;
+	ucontrol->value.enumerated.item[0] = rx->hph_pwr_mode;
 	return 0;
 }
 
@@ -2402,7 +2410,7 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct rx_macro *rx = snd_soc_component_get_drvdata(component);
 
-	rx->hph_pwr_mode = ucontrol->value.integer.value[0];
+	rx->hph_pwr_mode = ucontrol->value.enumerated.item[0];
 	return 0;
 }
 
@@ -2688,8 +2696,8 @@
 	int reg, b2_reg;
 
 	/* Address does not automatically update if reading */
-	reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B1_CTL + 16 * iir_idx;
-	b2_reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B2_CTL + 16 * iir_idx;
+	reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B1_CTL + 0x80 * iir_idx;
+	b2_reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B2_CTL + 0x80 * iir_idx;
 
 	snd_soc_component_write(component, reg,
 				((band_idx * BAND_MAX + coeff_idx) *
@@ -2718,7 +2726,7 @@
 static void set_iir_band_coeff(struct snd_soc_component *component,
 			       int iir_idx, int band_idx, uint32_t value)
 {
-	int reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B2_CTL + 16 * iir_idx;
+	int reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B2_CTL + 0x80 * iir_idx;
 
 	snd_soc_component_write(component, reg, (value & 0xFF));
 	snd_soc_component_write(component, reg, (value >> 8) & 0xFF);
@@ -2739,7 +2747,7 @@
 	int iir_idx = ctl->iir_idx;
 	int band_idx = ctl->band_idx;
 	u32 coeff[BAND_MAX];
-	int reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B1_CTL + 16 * iir_idx;
+	int reg = CDC_RX_SIDETONE_IIR0_IIR_COEF_B1_CTL + 0x80 * iir_idx;
 
 	memcpy(&coeff[0], ucontrol->value.bytes.data, params->max);
 
@@ -3475,17 +3483,16 @@
 
 };
 
-static struct clk *rx_macro_register_mclk_output(struct rx_macro *rx)
+static int rx_macro_register_mclk_output(struct rx_macro *rx)
 {
 	struct device *dev = rx->dev;
-	struct device_node *np = dev->of_node;
 	const char *parent_clk_name = NULL;
 	const char *clk_name = "lpass-rx-mclk";
 	struct clk_hw *hw;
 	struct clk_init_data init;
 	int ret;
 
-	parent_clk_name = __clk_get_name(rx->clks[2].clk);
+	parent_clk_name = __clk_get_name(rx->mclk);
 
 	init.name = clk_name;
 	init.ops = &swclk_gate_ops;
@@ -3494,13 +3501,11 @@
 	init.num_parents = 1;
 	rx->hw.init = &init;
 	hw = &rx->hw;
-	ret = clk_hw_register(rx->dev, hw);
+	ret = devm_clk_hw_register(rx->dev, hw);
 	if (ret)
-		return ERR_PTR(ret);
-
-	of_clk_add_provider(np, of_clk_src_simple_get, hw->clk);
+		return ret;
 
-	return NULL;
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, hw);
 }
 
 static const struct snd_soc_component_driver rx_macro_component_drv = {
@@ -3525,23 +3530,33 @@
 	if (!rx)
 		return -ENOMEM;
 
-	rx->clks[0].id = "macro";
-	rx->clks[1].id = "dcodec";
-	rx->clks[2].id = "mclk";
-	rx->clks[3].id = "npl";
-	rx->clks[4].id = "fsgen";
-
-	ret = devm_clk_bulk_get(dev, RX_NUM_CLKS_MAX, rx->clks);
-	if (ret) {
-		dev_err(dev, "Error getting RX Clocks (%d)\n", ret);
-		return ret;
-	}
+	rx->macro = devm_clk_get_optional(dev, "macro");
+	if (IS_ERR(rx->macro))
+		return PTR_ERR(rx->macro);
+
+	rx->dcodec = devm_clk_get_optional(dev, "dcodec");
+	if (IS_ERR(rx->dcodec))
+		return PTR_ERR(rx->dcodec);
+
+	rx->mclk = devm_clk_get(dev, "mclk");
+	if (IS_ERR(rx->mclk))
+		return PTR_ERR(rx->mclk);
+
+	rx->npl = devm_clk_get(dev, "npl");
+	if (IS_ERR(rx->npl))
+		return PTR_ERR(rx->npl);
+
+	rx->fsgen = devm_clk_get(dev, "fsgen");
+	if (IS_ERR(rx->fsgen))
+		return PTR_ERR(rx->fsgen);
 
 	base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(base))
 		return PTR_ERR(base);
 
 	rx->regmap = devm_regmap_init_mmio(dev, base, &rx_regmap_config);
+	if (IS_ERR(rx->regmap))
+		return PTR_ERR(rx->regmap);
 
 	dev_set_drvdata(dev, rx);
 
@@ -3549,21 +3564,52 @@
 	rx->dev = dev;
 
 	/* set MCLK and NPL rates */
-	clk_set_rate(rx->clks[2].clk, MCLK_FREQ);
-	clk_set_rate(rx->clks[3].clk, 2 * MCLK_FREQ);
+	clk_set_rate(rx->mclk, MCLK_FREQ);
+	clk_set_rate(rx->npl, MCLK_FREQ);
 
-	ret = clk_bulk_prepare_enable(RX_NUM_CLKS_MAX, rx->clks);
+	ret = clk_prepare_enable(rx->macro);
 	if (ret)
-		return ret;
+		goto err;
 
-	rx_macro_register_mclk_output(rx);
+	ret = clk_prepare_enable(rx->dcodec);
+	if (ret)
+		goto err_dcodec;
+
+	ret = clk_prepare_enable(rx->mclk);
+	if (ret)
+		goto err_mclk;
+
+	ret = clk_prepare_enable(rx->npl);
+	if (ret)
+		goto err_npl;
+
+	ret = clk_prepare_enable(rx->fsgen);
+	if (ret)
+		goto err_fsgen;
+
+	ret = rx_macro_register_mclk_output(rx);
+	if (ret)
+		goto err_clkout;
 
 	ret = devm_snd_soc_register_component(dev, &rx_macro_component_drv,
 					      rx_macro_dai,
 					      ARRAY_SIZE(rx_macro_dai));
 	if (ret)
-		clk_bulk_disable_unprepare(RX_NUM_CLKS_MAX, rx->clks);
+		goto err_clkout;
+
+	return 0;
 
+err_clkout:
+	clk_disable_unprepare(rx->fsgen);
+err_fsgen:
+	clk_disable_unprepare(rx->npl);
+err_npl:
+	clk_disable_unprepare(rx->mclk);
+err_mclk:
+	clk_disable_unprepare(rx->dcodec);
+err_dcodec:
+	clk_disable_unprepare(rx->macro);
+err:
 	return ret;
 }
 
@@ -3571,8 +3617,12 @@
 {
 	struct rx_macro *rx = dev_get_drvdata(&pdev->dev);
 
-	of_clk_del_provider(pdev->dev.of_node);
-	clk_bulk_disable_unprepare(RX_NUM_CLKS_MAX, rx->clks);
+	clk_disable_unprepare(rx->mclk);
+	clk_disable_unprepare(rx->npl);
+	clk_disable_unprepare(rx->fsgen);
+	clk_disable_unprepare(rx->macro);
+	clk_disable_unprepare(rx->dcodec);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/lpass-tx-macro.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/lpass-tx-macro.c
@@ -6,6 +6,7 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <sound/soc.h>
 #include <sound/soc-dapm.h>
@@ -199,7 +200,7 @@
 #define TX_MACRO_AMIC_UNMUTE_DELAY_MS	100
 #define TX_MACRO_DMIC_HPF_DELAY_MS	300
 #define TX_MACRO_AMIC_HPF_DELAY_MS	300
-#define MCLK_FREQ		9600000
+#define MCLK_FREQ		19200000
 
 enum {
 	TX_MACRO_AIF_INVALID = 0,
@@ -238,7 +239,7 @@
 
 struct tx_mute_work {
 	struct tx_macro *tx;
-	u32 decimator;
+	u8 decimator;
 	struct delayed_work dwork;
 };
 
@@ -258,7 +259,11 @@
 	unsigned long active_ch_cnt[TX_MACRO_MAX_DAIS];
 	unsigned long active_decimator[TX_MACRO_MAX_DAIS];
 	struct regmap *regmap;
-	struct clk_bulk_data clks[TX_NUM_CLKS_MAX];
+	struct clk *mclk;
+	struct clk *npl;
+	struct clk *macro;
+	struct clk *dcodec;
+	struct clk *fsgen;
 	struct clk_hw hw;
 	bool dec_active[NUM_DECIMATORS];
 	bool reset_swr;
@@ -627,7 +632,7 @@
 	return 0;
 }
 
-static bool is_amic_enabled(struct snd_soc_component *component, int decimator)
+static bool is_amic_enabled(struct snd_soc_component *component, u8 decimator)
 {
 	u16 adc_mux_reg, adc_reg, adc_n;
 
@@ -738,6 +743,8 @@
 	struct tx_macro *tx = snd_soc_component_get_drvdata(component);
 
 	val = ucontrol->value.enumerated.item[0];
+	if (val >= e->items)
+		return -EINVAL;
 
 	switch (e->reg) {
 	case CDC_TX_INP_MUX_ADC_MUX0_CFG0:
@@ -764,6 +771,9 @@
 	case CDC_TX_INP_MUX_ADC_MUX7_CFG0:
 		mic_sel_reg = CDC_TX7_TX_PATH_CFG0;
 		break;
+	default:
+		dev_err(component->dev, "Error in configuration!!\n");
+		return -EINVAL;
 	}
 
 	if (val != 0) {
@@ -815,24 +825,30 @@
 	struct tx_macro *tx = snd_soc_component_get_drvdata(component);
 
 	if (enable) {
+		if (tx->active_decimator[dai_id] == dec_id)
+			return 0;
+
 		set_bit(dec_id, &tx->active_ch_mask[dai_id]);
 		tx->active_ch_cnt[dai_id]++;
 		tx->active_decimator[dai_id] = dec_id;
 	} else {
+		if (tx->active_decimator[dai_id] == -1)
+			return 0;
+
 		tx->active_ch_cnt[dai_id]--;
 		clear_bit(dec_id, &tx->active_ch_mask[dai_id]);
 		tx->active_decimator[dai_id] = -1;
 	}
 	snd_soc_dapm_mixer_update_power(widget->dapm, kcontrol, enable, update);
 
-	return 0;
+	return 1;
 }
 
 static int tx_macro_enable_dec(struct snd_soc_dapm_widget *w,
 			       struct snd_kcontrol *kcontrol, int event)
 {
 	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
-	unsigned int decimator;
+	u8 decimator;
 	u16 tx_vol_ctl_reg, dec_cfg_reg, hpf_gate_reg, tx_gain_ctl_reg;
 	u8 hpf_cut_off_freq;
 	int hpf_delay = TX_MACRO_DMIC_HPF_DELAY_MS;
@@ -1011,9 +1027,12 @@
 	int path = e->shift_l;
 	struct tx_macro *tx = snd_soc_component_get_drvdata(component);
 
+	if (tx->dec_mode[path] == value)
+		return 0;
+
 	tx->dec_mode[path] = value;
 
-	return 0;
+	return 1;
 }
 
 static int tx_macro_get_bcs(struct snd_kcontrol *kcontrol,
@@ -1044,7 +1063,8 @@
 			      struct snd_soc_dai *dai)
 {
 	struct snd_soc_component *component = dai->component;
-	u32 decimator, sample_rate;
+	u32 sample_rate;
+	u8 decimator;
 	int tx_fs_rate;
 	struct tx_macro *tx = snd_soc_component_get_drvdata(component);
 
@@ -1108,7 +1128,7 @@
 {
 	struct snd_soc_component *component = dai->component;
 	struct tx_macro *tx = snd_soc_component_get_drvdata(component);
-	u16 decimator;
+	u8 decimator;
 
 	decimator = tx->active_decimator[dai->id];
 
@@ -1736,17 +1756,16 @@
 
 };
 
-static struct clk *tx_macro_register_mclk_output(struct tx_macro *tx)
+static int tx_macro_register_mclk_output(struct tx_macro *tx)
 {
 	struct device *dev = tx->dev;
-	struct device_node *np = dev->of_node;
 	const char *parent_clk_name = NULL;
 	const char *clk_name = "lpass-tx-mclk";
 	struct clk_hw *hw;
 	struct clk_init_data init;
 	int ret;
 
-	parent_clk_name = __clk_get_name(tx->clks[2].clk);
+	parent_clk_name = __clk_get_name(tx->mclk);
 
 	init.name = clk_name;
 	init.ops = &swclk_gate_ops;
@@ -1755,13 +1774,11 @@
 	init.num_parents = 1;
 	tx->hw.init = &init;
 	hw = &tx->hw;
-	ret = clk_hw_register(tx->dev, hw);
+	ret = devm_clk_hw_register(dev, hw);
 	if (ret)
-		return ERR_PTR(ret);
-
-	of_clk_add_provider(np, of_clk_src_simple_get, hw->clk);
+		return ret;
 
-	return NULL;
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, hw);
 }
 
 static const struct snd_soc_component_driver tx_macro_component_drv = {
@@ -1786,23 +1803,33 @@
 	if (!tx)
 		return -ENOMEM;
 
-	tx->clks[0].id = "macro";
-	tx->clks[1].id = "dcodec";
-	tx->clks[2].id = "mclk";
-	tx->clks[3].id = "npl";
-	tx->clks[4].id = "fsgen";
-
-	ret = devm_clk_bulk_get(dev, TX_NUM_CLKS_MAX, tx->clks);
-	if (ret) {
-		dev_err(dev, "Error getting RX Clocks (%d)\n", ret);
-		return ret;
-	}
+	tx->macro = devm_clk_get_optional(dev, "macro");
+	if (IS_ERR(tx->macro))
+		return PTR_ERR(tx->macro);
+
+	tx->dcodec = devm_clk_get_optional(dev, "dcodec");
+	if (IS_ERR(tx->dcodec))
+		return PTR_ERR(tx->dcodec);
+
+	tx->mclk = devm_clk_get(dev, "mclk");
+	if (IS_ERR(tx->mclk))
+		return PTR_ERR(tx->mclk);
+
+	tx->npl = devm_clk_get(dev, "npl");
+	if (IS_ERR(tx->npl))
+		return PTR_ERR(tx->npl);
+
+	tx->fsgen = devm_clk_get(dev, "fsgen");
+	if (IS_ERR(tx->fsgen))
+		return PTR_ERR(tx->fsgen);
 
 	base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(base))
 		return PTR_ERR(base);
 
 	tx->regmap = devm_regmap_init_mmio(dev, base, &tx_regmap_config);
+	if (IS_ERR(tx->regmap))
+		return PTR_ERR(tx->regmap);
 
 	dev_set_drvdata(dev, tx);
 
@@ -1810,24 +1837,52 @@
 	tx->dev = dev;
 
 	/* set MCLK and NPL rates */
-	clk_set_rate(tx->clks[2].clk, MCLK_FREQ);
-	clk_set_rate(tx->clks[3].clk, 2 * MCLK_FREQ);
+	clk_set_rate(tx->mclk, MCLK_FREQ);
+	clk_set_rate(tx->npl, MCLK_FREQ);
 
-	ret = clk_bulk_prepare_enable(TX_NUM_CLKS_MAX, tx->clks);
+	ret = clk_prepare_enable(tx->macro);
 	if (ret)
-		return ret;
+		goto err;
 
-	tx_macro_register_mclk_output(tx);
+	ret = clk_prepare_enable(tx->dcodec);
+	if (ret)
+		goto err_dcodec;
+
+	ret = clk_prepare_enable(tx->mclk);
+	if (ret)
+		goto err_mclk;
+
+	ret = clk_prepare_enable(tx->npl);
+	if (ret)
+		goto err_npl;
+
+	ret = clk_prepare_enable(tx->fsgen);
+	if (ret)
+		goto err_fsgen;
+
+	ret = tx_macro_register_mclk_output(tx);
+	if (ret)
+		goto err_clkout;
 
 	ret = devm_snd_soc_register_component(dev, &tx_macro_component_drv,
 					      tx_macro_dai,
 					      ARRAY_SIZE(tx_macro_dai));
 	if (ret)
-		goto err;
-	return ret;
-err:
-	clk_bulk_disable_unprepare(TX_NUM_CLKS_MAX, tx->clks);
+		goto err_clkout;
 
+	return 0;
+
+err_clkout:
+	clk_disable_unprepare(tx->fsgen);
+err_fsgen:
+	clk_disable_unprepare(tx->npl);
+err_npl:
+	clk_disable_unprepare(tx->mclk);
+err_mclk:
+	clk_disable_unprepare(tx->dcodec);
+err_dcodec:
+	clk_disable_unprepare(tx->macro);
+err:
 	return ret;
 }
 
@@ -1835,9 +1890,11 @@
 {
 	struct tx_macro *tx = dev_get_drvdata(&pdev->dev);
 
-	of_clk_del_provider(pdev->dev.of_node);
-
-	clk_bulk_disable_unprepare(TX_NUM_CLKS_MAX, tx->clks);
+	clk_disable_unprepare(tx->macro);
+	clk_disable_unprepare(tx->dcodec);
+	clk_disable_unprepare(tx->mclk);
+	clk_disable_unprepare(tx->npl);
+	clk_disable_unprepare(tx->fsgen);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/lpass-va-macro.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/lpass-va-macro.c
@@ -780,7 +780,7 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	int path = e->shift_l;
 
-	ucontrol->value.integer.value[0] = va->dec_mode[path];
+	ucontrol->value.enumerated.item[0] = va->dec_mode[path];
 
 	return 0;
 }
@@ -789,7 +789,7 @@
 				 struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
-	int value = ucontrol->value.integer.value[0];
+	int value = ucontrol->value.enumerated.item[0];
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	int path = e->shift_l;
 	struct va_macro *va = snd_soc_component_get_drvdata(comp);
@@ -1408,7 +1408,7 @@
 	va->clks[1].id = "dcodec";
 	va->clks[2].id = "mclk";
 
-	ret = devm_clk_bulk_get(dev, VA_NUM_CLKS_MAX, va->clks);
+	ret = devm_clk_bulk_get_optional(dev, VA_NUM_CLKS_MAX, va->clks);
 	if (ret) {
 		dev_err(dev, "Error getting VA Clocks (%d)\n", ret);
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/lpass-wsa-macro.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/lpass-wsa-macro.c
@@ -1577,7 +1577,6 @@
 	u16 gain_reg;
 	u16 reg;
 	int val;
-	int offset_val = 0;
 	struct wsa_macro *wsa = snd_soc_component_get_drvdata(component);
 
 	if (w->shift == WSA_MACRO_COMP1) {
@@ -1616,10 +1615,8 @@
 					CDC_WSA_RX1_RX_PATH_MIX_SEC0,
 					CDC_WSA_RX_PGA_HALF_DB_MASK,
 					CDC_WSA_RX_PGA_HALF_DB_ENABLE);
-			offset_val = -2;
 		}
 		val = snd_soc_component_read(component, gain_reg);
-		val += offset_val;
 		snd_soc_component_write(component, gain_reg, val);
 		wsa_macro_config_ear_spkr_gain(component, wsa,
 						event, gain_reg);
@@ -1647,10 +1644,6 @@
 					CDC_WSA_RX1_RX_PATH_MIX_SEC0,
 					CDC_WSA_RX_PGA_HALF_DB_MASK,
 					CDC_WSA_RX_PGA_HALF_DB_DISABLE);
-			offset_val = 2;
-			val = snd_soc_component_read(component, gain_reg);
-			val += offset_val;
-			snd_soc_component_write(component, gain_reg, val);
 		}
 		wsa_macro_config_ear_spkr_gain(component, wsa,
 						event, gain_reg);
@@ -1678,6 +1671,9 @@
 		boost_path_cfg1 = CDC_WSA_RX1_RX_PATH_CFG1;
 		reg = CDC_WSA_RX1_RX_PATH_CTL;
 		reg_mix = CDC_WSA_RX1_RX_PATH_MIX_CTL;
+	} else {
+		dev_warn(component->dev, "Incorrect widget name in the driver\n");
+		return -EINVAL;
 	}
 
 	switch (event) {
@@ -2405,6 +2401,8 @@
 		return PTR_ERR(base);
 
 	wsa->regmap = devm_regmap_init_mmio(dev, base, &wsa_regmap_config);
+	if (IS_ERR(wsa->regmap))
+		return PTR_ERR(wsa->regmap);
 
 	dev_set_drvdata(dev, wsa);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/madera.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/madera.c
@@ -618,7 +618,13 @@
 end:
 	snd_soc_dapm_mutex_unlock(dapm);
 
-	return snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
+	ret = snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
+	if (ret < 0) {
+		dev_err(madera->dev, "Failed to update demux power state: %d\n", ret);
+		return ret;
+	}
+
+	return change;
 }
 EXPORT_SYMBOL_GPL(madera_out1_demux_put);
 
@@ -893,7 +899,7 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	const int adsp_num = e->shift_l;
 	const unsigned int item = ucontrol->value.enumerated.item[0];
-	int ret;
+	int ret = 0;
 
 	if (item >= e->items)
 		return -EINVAL;
@@ -910,10 +916,10 @@
 			 "Cannot change '%s' while in use by active audio paths\n",
 			 kcontrol->id.name);
 		ret = -EBUSY;
-	} else {
+	} else if (priv->adsp_rate_cache[adsp_num] != e->values[item]) {
 		/* Volatile register so defer until the codec is powered up */
 		priv->adsp_rate_cache[adsp_num] = e->values[item];
-		ret = 0;
+		ret = 1;
 	}
 
 	mutex_unlock(&priv->rate_lock);
@@ -2316,10 +2322,10 @@
 	case CS42L92:
 	case CS47L92:
 	case CS47L93:
-		out_up_delay = 6;
+		out_up_delay = 6000;
 		break;
 	default:
-		out_up_delay = 17;
+		out_up_delay = 17000;
 		break;
 	}
 
@@ -2350,7 +2356,7 @@
 		case MADERA_OUT3R_ENA_SHIFT:
 			priv->out_up_pending--;
 			if (!priv->out_up_pending) {
-				msleep(priv->out_up_delay);
+				fsleep(priv->out_up_delay);
 				priv->out_up_delay = 0;
 			}
 			break;
@@ -2369,7 +2375,7 @@
 		case MADERA_OUT3L_ENA_SHIFT:
 		case MADERA_OUT3R_ENA_SHIFT:
 			priv->out_down_pending++;
-			priv->out_down_delay++;
+			priv->out_down_delay += 1000;
 			break;
 		default:
 			break;
@@ -2386,7 +2392,7 @@
 		case MADERA_OUT3R_ENA_SHIFT:
 			priv->out_down_pending--;
 			if (!priv->out_down_pending) {
-				msleep(priv->out_down_delay);
+				fsleep(priv->out_down_delay);
 				priv->out_down_delay = 0;
 			}
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/max9759.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/max9759.c
@@ -64,7 +64,8 @@
 	struct snd_soc_component *c = snd_soc_kcontrol_component(kcontrol);
 	struct max9759 *priv = snd_soc_component_get_drvdata(c);
 
-	if (ucontrol->value.integer.value[0] > 3)
+	if (ucontrol->value.integer.value[0] < 0 ||
+	    ucontrol->value.integer.value[0] > 3)
 		return -EINVAL;
 
 	priv->gain = ucontrol->value.integer.value[0];
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/max98088.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/max98088.c
@@ -1319,6 +1319,7 @@
                                   enum snd_soc_bias_level level)
 {
 	struct max98088_priv *max98088 = snd_soc_component_get_drvdata(component);
+	int ret;
 
 	switch (level) {
 	case SND_SOC_BIAS_ON:
@@ -1334,10 +1335,13 @@
 		 */
 		if (!IS_ERR(max98088->mclk)) {
 			if (snd_soc_component_get_bias_level(component) ==
-			    SND_SOC_BIAS_ON)
+			    SND_SOC_BIAS_ON) {
 				clk_disable_unprepare(max98088->mclk);
-			else
-				clk_prepare_enable(max98088->mclk);
+			} else {
+				ret = clk_prepare_enable(max98088->mclk);
+				if (ret)
+					return ret;
+			}
 		}
 		break;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/max98090.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/max98090.c
@@ -393,7 +393,8 @@
 	struct soc_mixer_control *mc =
 		(struct soc_mixer_control *)kcontrol->private_value;
 	unsigned int mask = (1 << fls(mc->max)) - 1;
-	unsigned int sel = ucontrol->value.integer.value[0];
+	int sel_unchecked = ucontrol->value.integer.value[0];
+	unsigned int sel;
 	unsigned int val = snd_soc_component_read(component, mc->reg);
 	unsigned int *select;
 
@@ -413,6 +414,10 @@
 
 	val = (val >> mc->shift) & mask;
 
+	if (sel_unchecked < 0 || sel_unchecked > mc->max)
+		return -EINVAL;
+	sel = sel_unchecked;
+
 	*select = sel;
 
 	/* Setting a volume is only valid if it is already On */
@@ -427,7 +432,7 @@
 		mask << mc->shift,
 		sel << mc->shift);
 
-	return 0;
+	return *select != val;
 }
 
 static const char *max98090_perf_pwr_text[] =
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/max98373-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/max98373-i2c.c
@@ -551,6 +551,10 @@
 	max98373->cache = devm_kcalloc(&i2c->dev, max98373->cache_num,
 				       sizeof(*max98373->cache),
 				       GFP_KERNEL);
+	if (!max98373->cache) {
+		ret = -ENOMEM;
+		return ret;
+	}
 
 	for (i = 0; i < max98373->cache_num; i++)
 		max98373->cache[i].reg = max98373_i2c_cache_reg[i];
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/max98373-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/max98373-sdw.c
@@ -741,7 +741,7 @@
 static const struct snd_soc_dai_ops max98373_dai_sdw_ops = {
 	.hw_params = max98373_sdw_dai_hw_params,
 	.hw_free = max98373_pcm_hw_free,
-	.set_sdw_stream = max98373_set_sdw_stream,
+	.set_stream = max98373_set_sdw_stream,
 	.shutdown = max98373_shutdown,
 	.set_tdm_slot = max98373_sdw_set_tdm_slot,
 };
@@ -862,6 +862,16 @@
 	return max98373_init(slave, regmap);
 }
 
+static int max98373_sdw_remove(struct sdw_slave *slave)
+{
+	struct max98373_priv *max98373 = dev_get_drvdata(&slave->dev);
+
+	if (max98373->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	return 0;
+}
+
 #if defined(CONFIG_OF)
 static const struct of_device_id max98373_of_match[] = {
 	{ .compatible = "maxim,max98373", },
@@ -893,7 +903,7 @@
 		.pm = &max98373_pm,
 	},
 	.probe = max98373_sdw_probe,
-	.remove = NULL,
+	.remove = max98373_sdw_remove,
 	.ops = &max98373_slave_ops,
 	.id_table = max98373_id,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/msm8916-wcd-analog.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/msm8916-wcd-analog.c
@@ -1221,8 +1221,10 @@
 	}
 
 	irq = platform_get_irq_byname(pdev, "mbhc_switch_int");
-	if (irq < 0)
-		return irq;
+	if (irq < 0) {
+		ret = irq;
+		goto err_disable_clk;
+	}
 
 	ret = devm_request_threaded_irq(dev, irq, NULL,
 			       pm8916_mbhc_switch_irq_handler,
@@ -1234,8 +1236,10 @@
 
 	if (priv->mbhc_btn_enabled) {
 		irq = platform_get_irq_byname(pdev, "mbhc_but_press_det");
-		if (irq < 0)
-			return irq;
+		if (irq < 0) {
+			ret = irq;
+			goto err_disable_clk;
+		}
 
 		ret = devm_request_threaded_irq(dev, irq, NULL,
 				       mbhc_btn_press_irq_handler,
@@ -1246,8 +1250,10 @@
 			dev_err(dev, "cannot request mbhc button press irq\n");
 
 		irq = platform_get_irq_byname(pdev, "mbhc_but_rel_det");
-		if (irq < 0)
-			return irq;
+		if (irq < 0) {
+			ret = irq;
+			goto err_disable_clk;
+		}
 
 		ret = devm_request_threaded_irq(dev, irq, NULL,
 				       mbhc_btn_release_irq_handler,
@@ -1264,6 +1270,10 @@
 	return devm_snd_soc_register_component(dev, &pm8916_wcd_analog,
 				      pm8916_wcd_analog_dai,
 				      ARRAY_SIZE(pm8916_wcd_analog_dai));
+
+err_disable_clk:
+	clk_disable_unprepare(priv->mclk);
+	return ret;
 }
 
 static int pm8916_wcd_analog_spmi_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/msm8916-wcd-digital.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/msm8916-wcd-digital.c
@@ -328,8 +328,8 @@
 static const struct snd_kcontrol_new rx2_mix2_inp1_mux = SOC_DAPM_ENUM(
 				"RX2 MIX2 INP1 Mux", rx2_mix2_inp1_chain_enum);
 
-/* Digital Gain control -38.4 dB to +38.4 dB in 0.3 dB steps */
-static const DECLARE_TLV_DB_SCALE(digital_gain, -3840, 30, 0);
+/* Digital Gain control -84 dB to +40 dB in 1 dB steps */
+static const DECLARE_TLV_DB_SCALE(digital_gain, -8400, 100, -8400);
 
 /* Cutoff Freq for High Pass Filter at -3dB */
 static const char * const hpf_cutoff_text[] = {
@@ -510,15 +510,15 @@
 
 static const struct snd_kcontrol_new msm8916_wcd_digital_snd_controls[] = {
 	SOC_SINGLE_S8_TLV("RX1 Digital Volume", LPASS_CDC_RX1_VOL_CTL_B2_CTL,
-			  -128, 127, digital_gain),
+			-84, 40, digital_gain),
 	SOC_SINGLE_S8_TLV("RX2 Digital Volume", LPASS_CDC_RX2_VOL_CTL_B2_CTL,
-			  -128, 127, digital_gain),
+			-84, 40, digital_gain),
 	SOC_SINGLE_S8_TLV("RX3 Digital Volume", LPASS_CDC_RX3_VOL_CTL_B2_CTL,
-			  -128, 127, digital_gain),
+			-84, 40, digital_gain),
 	SOC_SINGLE_S8_TLV("TX1 Digital Volume", LPASS_CDC_TX1_VOL_CTL_GAIN,
-			  -128, 127, digital_gain),
+			-84, 40, digital_gain),
 	SOC_SINGLE_S8_TLV("TX2 Digital Volume", LPASS_CDC_TX2_VOL_CTL_GAIN,
-			  -128, 127, digital_gain),
+			-84, 40, digital_gain),
 	SOC_ENUM("TX1 HPF Cutoff", tx1_hpf_cutoff_enum),
 	SOC_ENUM("TX2 HPF Cutoff", tx2_hpf_cutoff_enum),
 	SOC_SINGLE("TX1 HPF Switch", LPASS_CDC_TX1_MUX_CTL, 3, 1, 0),
@@ -553,22 +553,22 @@
 	WCD_IIR_FILTER_CTL("IIR2 Band3", IIR2, BAND3),
 	WCD_IIR_FILTER_CTL("IIR2 Band4", IIR2, BAND4),
 	WCD_IIR_FILTER_CTL("IIR2 Band5", IIR2, BAND5),
-	SOC_SINGLE_SX_TLV("IIR1 INP1 Volume", LPASS_CDC_IIR1_GAIN_B1_CTL,
-			0,  -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR1 INP2 Volume", LPASS_CDC_IIR1_GAIN_B2_CTL,
-			0,  -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR1 INP3 Volume", LPASS_CDC_IIR1_GAIN_B3_CTL,
-			0,  -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR1 INP4 Volume", LPASS_CDC_IIR1_GAIN_B4_CTL,
-			0,  -84,	40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR2 INP1 Volume", LPASS_CDC_IIR2_GAIN_B1_CTL,
-			0,  -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR2 INP2 Volume", LPASS_CDC_IIR2_GAIN_B2_CTL,
-			0,  -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR2 INP3 Volume", LPASS_CDC_IIR2_GAIN_B3_CTL,
-			0,  -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("IIR2 INP4 Volume", LPASS_CDC_IIR2_GAIN_B4_CTL,
-			0,  -84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR1 INP1 Volume", LPASS_CDC_IIR1_GAIN_B1_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR1 INP2 Volume", LPASS_CDC_IIR1_GAIN_B2_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR1 INP3 Volume", LPASS_CDC_IIR1_GAIN_B3_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR1 INP4 Volume", LPASS_CDC_IIR1_GAIN_B4_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR2 INP1 Volume", LPASS_CDC_IIR2_GAIN_B1_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR2 INP2 Volume", LPASS_CDC_IIR2_GAIN_B2_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR2 INP3 Volume", LPASS_CDC_IIR2_GAIN_B3_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("IIR2 INP4 Volume", LPASS_CDC_IIR2_GAIN_B4_CTL,
+			-84, 40, digital_gain),
 
 };
 
@@ -1201,14 +1201,24 @@
 	ret = clk_prepare_enable(priv->mclk);
 	if (ret < 0) {
 		dev_err(dev, "failed to enable mclk %d\n", ret);
-		return ret;
+		goto err_clk;
 	}
 
 	dev_set_drvdata(dev, priv);
 
-	return devm_snd_soc_register_component(dev, &msm8916_wcd_digital,
+	ret = devm_snd_soc_register_component(dev, &msm8916_wcd_digital,
 				      msm8916_wcd_digital_dai,
 				      ARRAY_SIZE(msm8916_wcd_digital_dai));
+	if (ret)
+		goto err_mclk;
+
+	return 0;
+
+err_mclk:
+	clk_disable_unprepare(priv->mclk);
+err_clk:
+	clk_disable_unprepare(priv->ahbclk);
+	return ret;
 }
 
 static int msm8916_wcd_digital_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/mt6358.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/mt6358.c
@@ -107,6 +107,7 @@
 	priv->mtkaif_protocol = mtkaif_protocol;
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mt6358_set_mtkaif_protocol);
 
 static void playback_gpio_set(struct mt6358_priv *priv)
 {
@@ -273,6 +274,7 @@
 			   1 << RG_AUD_PAD_TOP_DAT_MISO_LOOPBACK_SFT);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mt6358_mtkaif_calibration_enable);
 
 int mt6358_mtkaif_calibration_disable(struct snd_soc_component *cmpnt)
 {
@@ -296,6 +298,7 @@
 	capture_gpio_reset(priv);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mt6358_mtkaif_calibration_disable);
 
 int mt6358_set_mtkaif_calibration_phase(struct snd_soc_component *cmpnt,
 					int phase_1, int phase_2)
@@ -310,6 +313,7 @@
 			   phase_2 << RG_AUD_PAD_TOP_PHASE_MODE2_SFT);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(mt6358_set_mtkaif_calibration_phase);
 
 /* dl pga gain */
 enum {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/mt6359-accdet.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/mt6359-accdet.c
@@ -675,6 +675,7 @@
 			       sizeof(struct three_key_threshold));
 	}
 
+	of_node_put(node);
 	dev_warn(priv->dev, "accdet caps=%x\n", priv->caps);
 
 	return 0;
@@ -964,7 +965,7 @@
 	mutex_init(&priv->res_lock);
 
 	priv->accdet_irq = platform_get_irq(pdev, 0);
-	if (priv->accdet_irq) {
+	if (priv->accdet_irq >= 0) {
 		ret = devm_request_threaded_irq(&pdev->dev, priv->accdet_irq,
 						NULL, mt6359_accdet_irq,
 						IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
@@ -978,7 +979,7 @@
 
 	if (priv->caps & ACCDET_PMIC_EINT0) {
 		priv->accdet_eint0 = platform_get_irq(pdev, 1);
-		if (priv->accdet_eint0) {
+		if (priv->accdet_eint0 >= 0) {
 			ret = devm_request_threaded_irq(&pdev->dev,
 							priv->accdet_eint0,
 							NULL, mt6359_accdet_irq,
@@ -993,7 +994,7 @@
 		}
 	} else if (priv->caps & ACCDET_PMIC_EINT1) {
 		priv->accdet_eint1 = platform_get_irq(pdev, 2);
-		if (priv->accdet_eint1) {
+		if (priv->accdet_eint1 >= 0) {
 			ret = devm_request_threaded_irq(&pdev->dev,
 							priv->accdet_eint1,
 							NULL, mt6359_accdet_irq,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/mt6359.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/mt6359.c
@@ -2780,6 +2780,7 @@
 
 	ret = of_property_read_u32(np, "mediatek,mic-type-2",
 				   &priv->mux_select[MUX_MIC_TYPE_2]);
+	of_node_put(np);
 	if (ret) {
 		dev_info(priv->dev,
 			 "%s() failed to read mic-type-2, use default (%d)\n",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/mt6660.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/mt6660.c
@@ -510,7 +510,11 @@
 	ret = devm_snd_soc_register_component(chip->dev,
 					       &mt6660_component_driver,
 					       &mt6660_codec_dai, 1);
+	if (ret)
+		pm_runtime_disable(chip->dev);
+
 	return ret;
+
 probe_fail:
 	_mt6660_chip_power_on(chip, 0);
 	mutex_destroy(&chip->io_lock);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/nau8822.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/nau8822.c
@@ -184,6 +184,7 @@
 	struct soc_bytes_ext *params = (void *)kcontrol->private_value;
 	int i, reg;
 	u16 reg_val, *val;
+	__be16 tmp;
 
 	val = (u16 *)ucontrol->value.bytes.data;
 	reg = NAU8822_REG_EQ1;
@@ -192,8 +193,8 @@
 		/* conversion of 16-bit integers between native CPU format
 		 * and big endian format
 		 */
-		reg_val = cpu_to_be16(reg_val);
-		memcpy(val + i, &reg_val, sizeof(reg_val));
+		tmp = cpu_to_be16(reg_val);
+		memcpy(val + i, &tmp, sizeof(tmp));
 	}
 
 	return 0;
@@ -216,6 +217,7 @@
 	void *data;
 	u16 *val, value;
 	int i, reg, ret;
+	__be16 *tmp;
 
 	data = kmemdup(ucontrol->value.bytes.data,
 		params->max, GFP_KERNEL | GFP_DMA);
@@ -228,7 +230,8 @@
 		/* conversion of 16-bit integers between native CPU format
 		 * and big endian format
 		 */
-		value = be16_to_cpu(*(val + i));
+		tmp = (__be16 *)(val + i);
+		value = be16_to_cpup(tmp);
 		ret = snd_soc_component_write(component, reg + i, value);
 		if (ret) {
 			dev_err(component->dev,
@@ -741,6 +744,8 @@
 		pll_param->mclk_scaler, pll_param->pre_factor);
 
 	snd_soc_component_update_bits(component,
+		NAU8822_REG_POWER_MANAGEMENT_1, NAU8822_PLL_EN_MASK, NAU8822_PLL_OFF);
+	snd_soc_component_update_bits(component,
 		NAU8822_REG_PLL_N, NAU8822_PLLMCLK_DIV2 | NAU8822_PLLN_MASK,
 		(pll_param->pre_factor ? NAU8822_PLLMCLK_DIV2 : 0) |
 		pll_param->pll_int);
@@ -757,6 +762,8 @@
 		pll_param->mclk_scaler << NAU8822_MCLKSEL_SFT);
 	snd_soc_component_update_bits(component,
 		NAU8822_REG_CLOCKING, NAU8822_CLKM_MASK, NAU8822_CLKM_PLL);
+	snd_soc_component_update_bits(component,
+		NAU8822_REG_POWER_MANAGEMENT_1, NAU8822_PLL_EN_MASK, NAU8822_PLL_ON);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/nau8822.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/nau8822.h
@@ -90,6 +90,9 @@
 #define NAU8822_REFIMP_3K			0x3
 #define NAU8822_IOBUF_EN			(0x1 << 2)
 #define NAU8822_ABIAS_EN			(0x1 << 3)
+#define NAU8822_PLL_EN_MASK			(0x1 << 5)
+#define NAU8822_PLL_ON				(0x1 << 5)
+#define NAU8822_PLL_OFF				(0x0 << 5)
 
 /* NAU8822_REG_AUDIO_INTERFACE (0x4) */
 #define NAU8822_AIFMT_MASK			(0x3 << 3)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/nau8824.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/nau8824.c
@@ -8,6 +8,7 @@
 
 #include <linux/module.h>
 #include <linux/delay.h>
+#include <linux/dmi.h>
 #include <linux/init.h>
 #include <linux/i2c.h>
 #include <linux/regmap.h>
@@ -27,6 +28,12 @@
 
 #include "nau8824.h"
 
+#define NAU8824_JD_ACTIVE_HIGH			BIT(0)
+
+static int nau8824_quirk;
+static int quirk_override = -1;
+module_param_named(quirk, quirk_override, uint, 0444);
+MODULE_PARM_DESC(quirk, "Board-specific quirk override");
 
 static int nau8824_config_sysclk(struct nau8824 *nau8824,
 	int clk_id, unsigned int freq);
@@ -1035,6 +1042,7 @@
 	struct snd_soc_component *component = dai->component;
 	struct nau8824 *nau8824 = snd_soc_component_get_drvdata(component);
 	unsigned int val_len = 0, osr, ctrl_val, bclk_fs, bclk_div;
+	int err = -EINVAL;
 
 	nau8824_sema_acquire(nau8824, HZ);
 
@@ -1051,7 +1059,7 @@
 		osr &= NAU8824_DAC_OVERSAMPLE_MASK;
 		if (nau8824_clock_check(nau8824, substream->stream,
 			nau8824->fs, osr))
-			return -EINVAL;
+			goto error;
 		regmap_update_bits(nau8824->regmap, NAU8824_REG_CLK_DIVIDER,
 			NAU8824_CLK_DAC_SRC_MASK,
 			osr_dac_sel[osr].clk_src << NAU8824_CLK_DAC_SRC_SFT);
@@ -1061,7 +1069,7 @@
 		osr &= NAU8824_ADC_SYNC_DOWN_MASK;
 		if (nau8824_clock_check(nau8824, substream->stream,
 			nau8824->fs, osr))
-			return -EINVAL;
+			goto error;
 		regmap_update_bits(nau8824->regmap, NAU8824_REG_CLK_DIVIDER,
 			NAU8824_CLK_ADC_SRC_MASK,
 			osr_adc_sel[osr].clk_src << NAU8824_CLK_ADC_SRC_SFT);
@@ -1082,7 +1090,7 @@
 		else if (bclk_fs <= 256)
 			bclk_div = 0;
 		else
-			return -EINVAL;
+			goto error;
 		regmap_update_bits(nau8824->regmap,
 			NAU8824_REG_PORT0_I2S_PCM_CTRL_2,
 			NAU8824_I2S_LRC_DIV_MASK | NAU8824_I2S_BLK_DIV_MASK,
@@ -1103,15 +1111,17 @@
 		val_len |= NAU8824_I2S_DL_32;
 		break;
 	default:
-		return -EINVAL;
+		goto error;
 	}
 
 	regmap_update_bits(nau8824->regmap, NAU8824_REG_PORT0_I2S_PCM_CTRL_1,
 		NAU8824_I2S_DL_MASK, val_len);
+	err = 0;
 
+ error:
 	nau8824_sema_release(nau8824);
 
-	return 0;
+	return err;
 }
 
 static int nau8824_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
@@ -1120,8 +1130,6 @@
 	struct nau8824 *nau8824 = snd_soc_component_get_drvdata(component);
 	unsigned int ctrl1_val = 0, ctrl2_val = 0;
 
-	nau8824_sema_acquire(nau8824, HZ);
-
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
 	case SND_SOC_DAIFMT_CBM_CFM:
 		ctrl2_val |= NAU8824_I2S_MS_MASTER;
@@ -1163,6 +1171,8 @@
 		return -EINVAL;
 	}
 
+	nau8824_sema_acquire(nau8824, HZ);
+
 	regmap_update_bits(nau8824->regmap, NAU8824_REG_PORT0_I2S_PCM_CTRL_1,
 		NAU8824_I2S_DF_MASK | NAU8824_I2S_BP_MASK |
 		NAU8824_I2S_PCMB_EN, ctrl1_val);
@@ -1845,6 +1855,58 @@
 	return 0;
 }
 
+/* Please keep this list alphabetically sorted */
+static const struct dmi_system_id nau8824_quirk_table[] = {
+	{
+		/* Cyberbook T116 rugged tablet */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "Default string"),
+			DMI_EXACT_MATCH(DMI_BOARD_NAME, "Cherry Trail CR"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "20170531"),
+		},
+		.driver_data = (void *)(NAU8824_JD_ACTIVE_HIGH),
+	},
+	{
+		/* Positivo CW14Q01P */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Positivo Tecnologia SA"),
+			DMI_MATCH(DMI_BOARD_NAME, "CW14Q01P"),
+		},
+		.driver_data = (void *)(NAU8824_JD_ACTIVE_HIGH),
+	},
+	{
+		/* Positivo K1424G */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Positivo Tecnologia SA"),
+			DMI_MATCH(DMI_BOARD_NAME, "K1424G"),
+		},
+		.driver_data = (void *)(NAU8824_JD_ACTIVE_HIGH),
+	},
+	{
+		/* Positivo N14ZP74G */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Positivo Tecnologia SA"),
+			DMI_MATCH(DMI_BOARD_NAME, "N14ZP74G"),
+		},
+		.driver_data = (void *)(NAU8824_JD_ACTIVE_HIGH),
+	},
+	{}
+};
+
+static void nau8824_check_quirks(void)
+{
+	const struct dmi_system_id *dmi_id;
+
+	if (quirk_override != -1) {
+		nau8824_quirk = quirk_override;
+		return;
+	}
+
+	dmi_id = dmi_first_match(nau8824_quirk_table);
+	if (dmi_id)
+		nau8824_quirk = (unsigned long)dmi_id->driver_data;
+}
+
 static int nau8824_i2c_probe(struct i2c_client *i2c,
 	const struct i2c_device_id *id)
 {
@@ -1869,6 +1931,11 @@
 	nau8824->irq = i2c->irq;
 	sema_init(&nau8824->jd_sem, 1);
 
+	nau8824_check_quirks();
+
+	if (nau8824_quirk & NAU8824_JD_ACTIVE_HIGH)
+		nau8824->jkdet_polarity = 0;
+
 	nau8824_print_device_properties(nau8824);
 
 	ret = regmap_read(nau8824->regmap, NAU8824_REG_I2C_DEVICE_ID, &value);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/pcm512x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/pcm512x.c
@@ -1635,7 +1635,7 @@
 			if (val > 6) {
 				dev_err(dev, "Invalid pll-in\n");
 				ret = -EINVAL;
-				goto err_clk;
+				goto err_pm;
 			}
 			pcm512x->pll_in = val;
 		}
@@ -1644,7 +1644,7 @@
 			if (val > 6) {
 				dev_err(dev, "Invalid pll-out\n");
 				ret = -EINVAL;
-				goto err_clk;
+				goto err_pm;
 			}
 			pcm512x->pll_out = val;
 		}
@@ -1653,12 +1653,12 @@
 			dev_err(dev,
 				"Error: both pll-in and pll-out, or none\n");
 			ret = -EINVAL;
-			goto err_clk;
+			goto err_pm;
 		}
 		if (pcm512x->pll_in && pcm512x->pll_in == pcm512x->pll_out) {
 			dev_err(dev, "Error: pll-in == pll-out\n");
 			ret = -EINVAL;
-			goto err_clk;
+			goto err_pm;
 		}
 	}
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rk3328_codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rk3328_codec.c
@@ -481,7 +481,7 @@
 	ret = clk_prepare_enable(rk3328->pclk);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to enable acodec pclk\n");
-		return ret;
+		goto err_unprepare_mclk;
 	}
 
 	base = devm_platform_ioremap_resource(pdev, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rk817_codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rk817_codec.c
@@ -489,7 +489,7 @@
 
 	rk817_codec_parse_dt_property(&pdev->dev, rk817_codec_data);
 
-	rk817_codec_data->mclk = clk_get(pdev->dev.parent, "mclk");
+	rk817_codec_data->mclk = devm_clk_get(pdev->dev.parent, "mclk");
 	if (IS_ERR(rk817_codec_data->mclk)) {
 		dev_dbg(&pdev->dev, "Unable to get mclk\n");
 		ret = -ENXIO;
@@ -508,12 +508,14 @@
 	if (ret < 0) {
 		dev_err(&pdev->dev, "%s() register codec error %d\n",
 			__func__, ret);
-		goto err_;
+		goto err_clk;
 	}
 
 	return 0;
-err_:
 
+err_clk:
+	clk_disable_unprepare(rk817_codec_data->mclk);
+err_:
 	return ret;
 }
 
@@ -539,3 +541,4 @@
 MODULE_DESCRIPTION("ASoC RK817 codec driver");
 MODULE_AUTHOR("binyuan <kevan.lan@rock-chips.com>");
 MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:rk817-codec");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt1019.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt1019.c
@@ -391,18 +391,18 @@
 			unsigned int rx_mask, int slots, int slot_width)
 {
 	struct snd_soc_component *component = dai->component;
-	unsigned int val = 0, rx_slotnum;
+	unsigned int cn = 0, cl = 0, rx_slotnum;
 	int ret = 0, first_bit;
 
 	switch (slots) {
 	case 4:
-		val |= RT1019_I2S_TX_4CH;
+		cn = RT1019_I2S_TX_4CH;
 		break;
 	case 6:
-		val |= RT1019_I2S_TX_6CH;
+		cn = RT1019_I2S_TX_6CH;
 		break;
 	case 8:
-		val |= RT1019_I2S_TX_8CH;
+		cn = RT1019_I2S_TX_8CH;
 		break;
 	case 2:
 		break;
@@ -412,16 +412,16 @@
 
 	switch (slot_width) {
 	case 20:
-		val |= RT1019_I2S_DL_20;
+		cl = RT1019_TDM_CL_20;
 		break;
 	case 24:
-		val |= RT1019_I2S_DL_24;
+		cl = RT1019_TDM_CL_24;
 		break;
 	case 32:
-		val |= RT1019_I2S_DL_32;
+		cl = RT1019_TDM_CL_32;
 		break;
 	case 8:
-		val |= RT1019_I2S_DL_8;
+		cl = RT1019_TDM_CL_8;
 		break;
 	case 16:
 		break;
@@ -470,8 +470,10 @@
 		goto _set_tdm_err_;
 	}
 
+	snd_soc_component_update_bits(component, RT1019_TDM_1,
+		RT1019_TDM_CL_MASK, cl);
 	snd_soc_component_update_bits(component, RT1019_TDM_2,
-		RT1019_I2S_CH_TX_MASK | RT1019_I2S_DF_MASK, val);
+		RT1019_I2S_CH_TX_MASK, cn);
 
 _set_tdm_err_:
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt1019.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt1019.h
@@ -95,6 +95,12 @@
 #define RT1019_TDM_BCLK_MASK		(0x1 << 6)
 #define RT1019_TDM_BCLK_NORM		(0x0 << 6)
 #define RT1019_TDM_BCLK_INV			(0x1 << 6)
+#define RT1019_TDM_CL_MASK			(0x7)
+#define RT1019_TDM_CL_8				(0x4)
+#define RT1019_TDM_CL_32			(0x3)
+#define RT1019_TDM_CL_24			(0x2)
+#define RT1019_TDM_CL_20			(0x1)
+#define RT1019_TDM_CL_16			(0x0)
 
 /* 0x0401 TDM Control-2 */
 #define RT1019_I2S_CH_TX_MASK		(0x3 << 6)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt1308-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt1308-sdw.c
@@ -613,7 +613,7 @@
 static const struct snd_soc_dai_ops rt1308_aif_dai_ops = {
 	.hw_params = rt1308_sdw_hw_params,
 	.hw_free	= rt1308_sdw_pcm_hw_free,
-	.set_sdw_stream	= rt1308_set_sdw_stream,
+	.set_stream	= rt1308_set_sdw_stream,
 	.shutdown	= rt1308_sdw_shutdown,
 	.set_tdm_slot	= rt1308_sdw_set_tdm_slot,
 };
@@ -683,6 +683,16 @@
 	return 0;
 }
 
+static int rt1308_sdw_remove(struct sdw_slave *slave)
+{
+	struct rt1308_sdw_priv *rt1308 = dev_get_drvdata(&slave->dev);
+
+	if (rt1308->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	return 0;
+}
+
 static const struct sdw_device_id rt1308_id[] = {
 	SDW_SLAVE_ENTRY_EXT(0x025d, 0x1308, 0x2, 0, 0),
 	{},
@@ -742,6 +752,7 @@
 		.pm = &rt1308_pm,
 	},
 	.probe = rt1308_sdw_probe,
+	.remove = rt1308_sdw_remove,
 	.ops = &rt1308_slave_ops,
 	.id_table = rt1308_id,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt1308-sdw.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt1308-sdw.h
@@ -139,9 +139,11 @@
 	{ 0x3005, 0x23 },
 	{ 0x3008, 0x02 },
 	{ 0x300a, 0x00 },
+	{ 0xc000 | (RT1308_DATA_PATH << 4), 0x00 },
 	{ 0xc003 | (RT1308_DAC_SET << 4), 0x00 },
 	{ 0xc001 | (RT1308_POWER << 4), 0x00 },
 	{ 0xc002 | (RT1308_POWER << 4), 0x00 },
+	{ 0xc000 | (RT1308_POWER_STATUS << 4), 0x00 },
 };
 
 #define RT1308_SDW_OFFSET 0xc000
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt1316-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt1316-sdw.c
@@ -602,7 +602,7 @@
 static const struct snd_soc_dai_ops rt1316_aif_dai_ops = {
 	.hw_params = rt1316_sdw_hw_params,
 	.hw_free	= rt1316_sdw_pcm_hw_free,
-	.set_sdw_stream	= rt1316_set_sdw_stream,
+	.set_stream	= rt1316_set_sdw_stream,
 	.shutdown	= rt1316_sdw_shutdown,
 };
 
@@ -675,6 +675,16 @@
 	return rt1316_sdw_init(&slave->dev, regmap, slave);
 }
 
+static int rt1316_sdw_remove(struct sdw_slave *slave)
+{
+	struct rt1316_sdw_priv *rt1316 = dev_get_drvdata(&slave->dev);
+
+	if (rt1316->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	return 0;
+}
+
 static const struct sdw_device_id rt1316_id[] = {
 	SDW_SLAVE_ENTRY_EXT(0x025d, 0x1316, 0x3, 0x1, 0),
 	{},
@@ -734,6 +744,7 @@
 		.pm = &rt1316_pm,
 	},
 	.probe = rt1316_sdw_probe,
+	.remove = rt1316_sdw_remove,
 	.ops = &rt1316_slave_ops,
 	.id_table = rt1316_id,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt298.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt298.c
@@ -1173,6 +1173,13 @@
 			DMI_MATCH(DMI_PRODUCT_NAME, "Geminilake")
 		}
 	},
+	{
+		.ident = "Intel Kabylake R RVP",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Intel Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Kabylake Client platform")
+		}
+	},
 	{ }
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5514.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5514.c
@@ -419,7 +419,7 @@
 		}
 	}
 
-	return 0;
+	return 1;
 }
 
 static const struct snd_kcontrol_new rt5514_snd_controls[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5645.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5645.c
@@ -441,6 +441,7 @@
 	struct regmap *regmap;
 	struct i2c_client *i2c;
 	struct gpio_desc *gpiod_hp_det;
+	struct gpio_desc *gpiod_cbj_sleeve;
 	struct snd_soc_jack *hp_jack;
 	struct snd_soc_jack *mic_jack;
 	struct snd_soc_jack *btn_jack;
@@ -448,6 +449,7 @@
 	struct regulator_bulk_data supplies[ARRAY_SIZE(rt5645_supply_names)];
 	struct rt5645_eq_param_s *eq_param;
 	struct timer_list btn_check_timer;
+	struct mutex jd_mutex;
 
 	int codec_type;
 	int sysclk;
@@ -3178,6 +3180,9 @@
 		regmap_update_bits(rt5645->regmap, RT5645_IN1_CTRL2,
 			RT5645_CBJ_MN_JD, 0);
 
+		if (rt5645->gpiod_cbj_sleeve)
+			gpiod_set_value(rt5645->gpiod_cbj_sleeve, 1);
+
 		msleep(600);
 		regmap_read(rt5645->regmap, RT5645_IN1_CTRL3, &val);
 		val &= 0x7;
@@ -3189,9 +3194,13 @@
 				rt5645_enable_push_button_irq(component, true);
 			}
 		} else {
+			if (rt5645->en_button_func)
+				rt5645_enable_push_button_irq(component, false);
 			snd_soc_dapm_disable_pin(dapm, "Mic Det Power");
 			snd_soc_dapm_sync(dapm);
 			rt5645->jack_type = SND_JACK_HEADPHONE;
+			if (rt5645->gpiod_cbj_sleeve)
+				gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0);
 		}
 		if (rt5645->pdata.level_trigger_irq)
 			regmap_update_bits(rt5645->regmap, RT5645_IRQ_CTRL2,
@@ -3217,6 +3226,9 @@
 		if (rt5645->pdata.level_trigger_irq)
 			regmap_update_bits(rt5645->regmap, RT5645_IRQ_CTRL2,
 				RT5645_JD_1_1_MASK, RT5645_JD_1_1_INV);
+
+		if (rt5645->gpiod_cbj_sleeve)
+			gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0);
 	}
 
 	return rt5645->jack_type;
@@ -3251,6 +3263,8 @@
 				RT5645_GP1_PIN_IRQ, RT5645_GP1_PIN_IRQ);
 		regmap_update_bits(rt5645->regmap, RT5645_GEN_CTRL1,
 				RT5645_DIG_GATE_CTRL, RT5645_DIG_GATE_CTRL);
+		regmap_update_bits(rt5645->regmap, RT5645_DEPOP_M1,
+				RT5645_HP_CB_MASK, RT5645_HP_CB_PU);
 	}
 	rt5645_irq(0, rt5645);
 
@@ -3267,6 +3281,8 @@
 	if (!rt5645->component)
 		return;
 
+	mutex_lock(&rt5645->jd_mutex);
+
 	switch (rt5645->pdata.jd_mode) {
 	case 0: /* Not using rt5645 JD */
 		if (rt5645->gpiod_hp_det) {
@@ -3281,6 +3297,7 @@
 				    report, SND_JACK_HEADPHONE);
 		snd_soc_jack_report(rt5645->mic_jack,
 				    report, SND_JACK_MICROPHONE);
+		mutex_unlock(&rt5645->jd_mutex);
 		return;
 	case 4:
 		val = snd_soc_component_read(rt5645->component, RT5645_A_JD_CTRL1) & 0x0020;
@@ -3293,7 +3310,7 @@
 
 	if (!val && (rt5645->jack_type == 0)) { /* jack in */
 		report = rt5645_jack_detect(rt5645->component, 1);
-	} else if (!val && rt5645->jack_type != 0) {
+	} else if (!val && rt5645->jack_type == SND_JACK_HEADSET) {
 		/* for push button and jack out */
 		btn_type = 0;
 		if (snd_soc_component_read(rt5645->component, RT5645_INT_IRQ_ST) & 0x4) {
@@ -3349,6 +3366,8 @@
 		rt5645_jack_detect(rt5645->component, 0);
 	}
 
+	mutex_unlock(&rt5645->jd_mutex);
+
 	snd_soc_jack_report(rt5645->hp_jack, report, SND_JACK_HEADPHONE);
 	snd_soc_jack_report(rt5645->mic_jack, report, SND_JACK_MICROPHONE);
 	if (rt5645->en_button_func)
@@ -3793,6 +3812,16 @@
 		  DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
 		  DMI_EXACT_MATCH(DMI_BOARD_NAME, "Cherry Trail CR"),
 		  DMI_EXACT_MATCH(DMI_BOARD_VERSION, "Default string"),
+		  /*
+		   * Above strings are too generic, LattePanda BIOS versions for
+		   * all 4 hw revisions are:
+		   * DF-BI-7-S70CR100-*
+		   * DF-BI-7-S70CR110-*
+		   * DF-BI-7-S70CR200-*
+		   * LP-BS-7-S70CR700-*
+		   * Do a partial match for S70CR to avoid false positive matches.
+		   */
+		  DMI_MATCH(DMI_BIOS_VERSION, "S70CR"),
 		},
 		.driver_data = (void *)&lattepanda_board_platform_data,
 	},
@@ -3819,14 +3848,6 @@
 		},
 		.driver_data = (void *)&ecs_ef20_platform_data,
 	},
-	{
-		.ident = "EF20EA",
-		.callback = cht_rt5645_ef20_quirk_cb,
-		.matches = {
-			DMI_MATCH(DMI_PRODUCT_NAME, "EF20EA"),
-		},
-		.driver_data = (void *)&ecs_ef20_platform_data,
-	},
 	{ }
 };
 
@@ -3921,6 +3942,16 @@
 			return ret;
 	}
 
+	rt5645->gpiod_cbj_sleeve = devm_gpiod_get_optional(&i2c->dev, "cbj-sleeve",
+							   GPIOD_OUT_LOW);
+
+	if (IS_ERR(rt5645->gpiod_cbj_sleeve)) {
+		ret = PTR_ERR(rt5645->gpiod_cbj_sleeve);
+		dev_info(&i2c->dev, "failed to initialize gpiod, ret=%d\n", ret);
+		if (ret != -ENOENT)
+			return ret;
+	}
+
 	for (i = 0; i < ARRAY_SIZE(rt5645->supplies); i++)
 		rt5645->supplies[i].supply = rt5645_supply_names[i];
 
@@ -4119,6 +4150,7 @@
 	}
 	timer_setup(&rt5645->btn_check_timer, rt5645_btn_check_callback, 0);
 
+	mutex_init(&rt5645->jd_mutex);
 	INIT_DELAYED_WORK(&rt5645->jack_detect_work, rt5645_jack_detect_work);
 	INIT_DELAYED_WORK(&rt5645->rcclock_work, rt5645_rcclock_work);
 
@@ -4154,9 +4186,17 @@
 	if (i2c->irq)
 		free_irq(i2c->irq, rt5645);
 
+	/*
+	 * Since the rt5645_btn_check_callback() can queue jack_detect_work,
+	 * the timer need to be delted first
+	 */
+	del_timer_sync(&rt5645->btn_check_timer);
+
 	cancel_delayed_work_sync(&rt5645->jack_detect_work);
 	cancel_delayed_work_sync(&rt5645->rcclock_work);
-	del_timer_sync(&rt5645->btn_check_timer);
+
+	if (rt5645->gpiod_cbj_sleeve)
+		gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0);
 
 	regulator_bulk_disable(ARRAY_SIZE(rt5645->supplies), rt5645->supplies);
 
@@ -4175,6 +4215,9 @@
 		0);
 	msleep(20);
 	regmap_write(rt5645->regmap, RT5645_RESET, 0);
+
+	if (rt5645->gpiod_cbj_sleeve)
+		gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0);
 }
 
 static struct i2c_driver rt5645_i2c_driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5651.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5651.c
@@ -2261,11 +2261,8 @@
 
 	ret = devm_request_irq(&i2c->dev, rt5651->irq, rt5651_irq,
 			       IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING
-			       | IRQF_ONESHOT, "rt5651", rt5651);
-	if (ret == 0) {
-		/* Gets re-enabled by rt5651_set_jack() */
-		disable_irq(rt5651->irq);
-	} else {
+			       | IRQF_ONESHOT | IRQF_NO_AUTOEN, "rt5651", rt5651);
+	if (ret) {
 		dev_warn(&i2c->dev, "Failed to reguest IRQ %d: %d\n",
 			 rt5651->irq, ret);
 		rt5651->irq = -ENXIO;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5663.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5663.c
@@ -3461,6 +3461,7 @@
 static int rt5663_parse_dp(struct rt5663_priv *rt5663, struct device *dev)
 {
 	int table_size;
+	int ret;
 
 	device_property_read_u32(dev, "realtek,dc_offset_l_manual",
 		&rt5663->pdata.dc_offset_l_manual);
@@ -3477,9 +3478,13 @@
 		table_size = sizeof(struct impedance_mapping_table) *
 			rt5663->pdata.impedance_sensing_num;
 		rt5663->imp_table = devm_kzalloc(dev, table_size, GFP_KERNEL);
-		device_property_read_u32_array(dev,
+		if (!rt5663->imp_table)
+			return -ENOMEM;
+		ret = device_property_read_u32_array(dev,
 			"realtek,impedance_sensing_table",
 			(u32 *)rt5663->imp_table, table_size);
+		if (ret)
+			return ret;
 	}
 
 	return 0;
@@ -3504,8 +3509,11 @@
 
 	if (pdata)
 		rt5663->pdata = *pdata;
-	else
-		rt5663_parse_dp(rt5663, &i2c->dev);
+	else {
+		ret = rt5663_parse_dp(rt5663, &i2c->dev);
+		if (ret)
+			return ret;
+	}
 
 	for (i = 0; i < ARRAY_SIZE(rt5663->supplies); i++)
 		rt5663->supplies[i].supply = rt5663_supply_names[i];
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5665.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5665.c
@@ -4472,6 +4472,8 @@
 	struct rt5665_priv *rt5665 = snd_soc_component_get_drvdata(component);
 
 	regmap_write(rt5665->regmap, RT5665_RESET, 0);
+
+	regulator_bulk_disable(ARRAY_SIZE(rt5665->supplies), rt5665->supplies);
 }
 
 #ifdef CONFIG_PM
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5668.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5668.c
@@ -1022,11 +1022,13 @@
 		container_of(work, struct rt5668_priv, jack_detect_work.work);
 	int val, btn_type;
 
-	while (!rt5668->component)
-		usleep_range(10000, 15000);
-
-	while (!rt5668->component->card->instantiated)
-		usleep_range(10000, 15000);
+	if (!rt5668->component || !rt5668->component->card ||
+	    !rt5668->component->card->instantiated) {
+		/* card not yet ready, try later */
+		mod_delayed_work(system_power_efficient_wq,
+				 &rt5668->jack_detect_work, msecs_to_jiffies(15));
+		return;
+	}
 
 	mutex_lock(&rt5668->calibrate_mutex);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5670.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5670.c
@@ -3313,8 +3313,6 @@
 	if (ret < 0)
 		goto err;
 
-	pm_runtime_put(&i2c->dev);
-
 	return 0;
 err:
 	pm_runtime_disable(&i2c->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5682-i2c.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5682-i2c.c
@@ -59,18 +59,12 @@
 	struct rt5682_priv *rt5682 = container_of(work, struct rt5682_priv,
 		jd_check_work.work);
 
-	if (snd_soc_component_read(rt5682->component, RT5682_AJD1_CTRL)
-		& RT5682_JDH_RS_MASK) {
+	if (snd_soc_component_read(rt5682->component, RT5682_AJD1_CTRL) & RT5682_JDH_RS_MASK)
 		/* jack out */
-		rt5682->jack_type = rt5682_headset_detect(rt5682->component, 0);
-
-		snd_soc_jack_report(rt5682->hs_jack, rt5682->jack_type,
-			SND_JACK_HEADSET |
-			SND_JACK_BTN_0 | SND_JACK_BTN_1 |
-			SND_JACK_BTN_2 | SND_JACK_BTN_3);
-	} else {
+		mod_delayed_work(system_power_efficient_wq,
+				 &rt5682->jack_detect_work, 0);
+	else
 		schedule_delayed_work(&rt5682->jd_check_work, 500);
-	}
 }
 
 static irqreturn_t rt5682_irq(int irq, void *data)
@@ -139,6 +133,8 @@
 
 	i2c_set_clientdata(i2c, rt5682);
 
+	rt5682->i2c_dev = &i2c->dev;
+
 	rt5682->pdata = i2s_default_platform_data;
 
 	if (pdata)
@@ -272,10 +268,32 @@
 		ret = devm_request_threaded_irq(&i2c->dev, i2c->irq, NULL,
 			rt5682_irq, IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING
 			| IRQF_ONESHOT, "rt5682", rt5682);
-		if (ret)
+		if (!ret)
+			rt5682->irq = i2c->irq;
+		else
 			dev_err(&i2c->dev, "Failed to reguest IRQ: %d\n", ret);
 	}
 
+#ifdef CONFIG_COMMON_CLK
+	/* Check if MCLK provided */
+	rt5682->mclk = devm_clk_get(&i2c->dev, "mclk");
+	if (IS_ERR(rt5682->mclk)) {
+		if (PTR_ERR(rt5682->mclk) != -ENOENT) {
+			ret = PTR_ERR(rt5682->mclk);
+			return ret;
+		}
+		rt5682->mclk = NULL;
+	}
+
+	/* Register CCF DAI clock control */
+	ret = rt5682_register_dai_clks(rt5682);
+	if (ret)
+		return ret;
+
+	/* Initial setup for CCF */
+	rt5682->lrck[RT5682_AIF1] = 48000;
+#endif
+
 	return devm_snd_soc_register_component(&i2c->dev,
 					       &rt5682_soc_component_dev,
 					       rt5682_dai, ARRAY_SIZE(rt5682_dai));
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5682-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5682-sdw.c
@@ -272,7 +272,7 @@
 static const struct snd_soc_dai_ops rt5682_sdw_ops = {
 	.hw_params	= rt5682_sdw_hw_params,
 	.hw_free	= rt5682_sdw_hw_free,
-	.set_sdw_stream	= rt5682_set_sdw_stream,
+	.set_stream	= rt5682_set_sdw_stream,
 	.shutdown	= rt5682_sdw_shutdown,
 };
 
@@ -719,9 +719,12 @@
 {
 	struct rt5682_priv *rt5682 = dev_get_drvdata(&slave->dev);
 
-	if (rt5682 && rt5682->hw_init)
+	if (rt5682->hw_init)
 		cancel_delayed_work_sync(&rt5682->jack_detect_work);
 
+	if (rt5682->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
 	return 0;
 }
 
@@ -783,8 +786,15 @@
 	if (!rt5682->first_hw_init)
 		return 0;
 
-	if (!slave->unattach_request)
+	if (!slave->unattach_request) {
+		mutex_lock(&rt5682->disable_irq_lock);
+		if (rt5682->disable_irq == true) {
+			sdw_write_no_pm(slave, SDW_SCP_INTMASK1, SDW_SCP_INT1_IMPL_DEF);
+			rt5682->disable_irq = false;
+		}
+		mutex_unlock(&rt5682->disable_irq_lock);
 		goto regmap_sync;
+	}
 
 	time = wait_for_completion_timeout(&slave->initialization_complete,
 				msecs_to_jiffies(RT5682_PROBE_TIMEOUT));
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5682.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5682.c
@@ -46,6 +46,10 @@
 	{RT5682_SAR_IL_CMD_1, 0x22b7},
 	{RT5682_SAR_IL_CMD_3, 0x0365},
 	{RT5682_SAR_IL_CMD_6, 0x0110},
+	{RT5682_CHARGE_PUMP_1, 0x0210},
+	{RT5682_HP_LOGIC_CTRL_2, 0x0007},
+	{RT5682_SAR_IL_CMD_2, 0xac00},
+	{RT5682_CBJ_CTRL_7, 0x0104},
 };
 
 void rt5682_apply_patch_list(struct rt5682_priv *rt5682, struct device *dev)
@@ -918,7 +922,7 @@
  *
  * Returns detect status.
  */
-int rt5682_headset_detect(struct snd_soc_component *component, int jack_insert)
+static int rt5682_headset_detect(struct snd_soc_component *component, int jack_insert)
 {
 	struct rt5682_priv *rt5682 = snd_soc_component_get_drvdata(component);
 	struct snd_soc_dapm_context *dapm = &component->dapm;
@@ -938,6 +942,10 @@
 		snd_soc_component_update_bits(component,
 			RT5682_HP_CHARGE_PUMP_1,
 			RT5682_OSW_L_MASK | RT5682_OSW_R_MASK, 0);
+		rt5682_enable_push_button_irq(component, false);
+		snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
+			RT5682_TRIG_JD_MASK, RT5682_TRIG_JD_LOW);
+		usleep_range(55000, 60000);
 		snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
 			RT5682_TRIG_JD_MASK, RT5682_TRIG_JD_HIGH);
 
@@ -999,7 +1007,6 @@
 	dev_dbg(component->dev, "jack_type = %d\n", rt5682->jack_type);
 	return rt5682->jack_type;
 }
-EXPORT_SYMBOL_GPL(rt5682_headset_detect);
 
 static int rt5682_set_jack_detect(struct snd_soc_component *component,
 		struct snd_soc_jack *hs_jack, void *data)
@@ -1082,14 +1089,20 @@
 {
 	struct rt5682_priv *rt5682 =
 		container_of(work, struct rt5682_priv, jack_detect_work.work);
+	struct snd_soc_dapm_context *dapm;
 	int val, btn_type;
 
-	while (!rt5682->component)
-		usleep_range(10000, 15000);
+	if (!rt5682->component || !rt5682->component->card ||
+	    !rt5682->component->card->instantiated) {
+		/* card not yet ready, try later */
+		mod_delayed_work(system_power_efficient_wq,
+				 &rt5682->jack_detect_work, msecs_to_jiffies(15));
+		return;
+	}
 
-	while (!rt5682->component->card->instantiated)
-		usleep_range(10000, 15000);
+	dapm = snd_soc_component_get_dapm(rt5682->component);
 
+	snd_soc_dapm_mutex_lock(dapm);
 	mutex_lock(&rt5682->calibrate_mutex);
 
 	val = snd_soc_component_read(rt5682->component, RT5682_AJD1_CTRL)
@@ -1149,6 +1162,9 @@
 		rt5682->irq_work_delay_time = 50;
 	}
 
+	mutex_unlock(&rt5682->calibrate_mutex);
+	snd_soc_dapm_mutex_unlock(dapm);
+
 	snd_soc_jack_report(rt5682->hs_jack, rt5682->jack_type,
 		SND_JACK_HEADSET |
 		SND_JACK_BTN_0 | SND_JACK_BTN_1 |
@@ -1161,8 +1177,6 @@
 		else
 			cancel_delayed_work_sync(&rt5682->jd_check_work);
 	}
-
-	mutex_unlock(&rt5682->calibrate_mutex);
 }
 EXPORT_SYMBOL_GPL(rt5682_jack_detect_handler);
 
@@ -1515,21 +1529,29 @@
 
 	switch (event) {
 	case SND_SOC_DAPM_PRE_PMU:
-		snd_soc_component_write(component,
-			RT5682_HP_LOGIC_CTRL_2, 0x0012);
-		snd_soc_component_write(component,
-			RT5682_HP_CTRL_2, 0x6000);
+		snd_soc_component_update_bits(component, RT5682_HP_CTRL_2,
+			RT5682_HP_C2_DAC_AMP_MUTE, 0);
+		snd_soc_component_update_bits(component, RT5682_HP_LOGIC_CTRL_2,
+			RT5682_HP_LC2_SIG_SOUR2_MASK, RT5682_HP_LC2_SIG_SOUR2_REG);
 		snd_soc_component_update_bits(component,
 			RT5682_DEPOP_1, 0x60, 0x60);
 		snd_soc_component_update_bits(component,
 			RT5682_DAC_ADC_DIG_VOL1, 0x00c0, 0x0080);
+		snd_soc_component_update_bits(component, RT5682_HP_CTRL_2,
+			RT5682_HP_C2_DAC_L_EN | RT5682_HP_C2_DAC_R_EN,
+			RT5682_HP_C2_DAC_L_EN | RT5682_HP_C2_DAC_R_EN);
+		usleep_range(5000, 10000);
+		snd_soc_component_update_bits(component, RT5682_CHARGE_PUMP_1,
+			RT5682_CP_SW_SIZE_MASK, RT5682_CP_SW_SIZE_L);
 		break;
 
 	case SND_SOC_DAPM_POST_PMD:
+		snd_soc_component_update_bits(component, RT5682_HP_CTRL_2,
+			RT5682_HP_C2_DAC_L_EN | RT5682_HP_C2_DAC_R_EN, 0);
+		snd_soc_component_update_bits(component, RT5682_CHARGE_PUMP_1,
+			RT5682_CP_SW_SIZE_MASK, RT5682_CP_SW_SIZE_M);
 		snd_soc_component_update_bits(component,
 			RT5682_DEPOP_1, 0x60, 0x0);
-		snd_soc_component_write(component,
-			RT5682_HP_CTRL_2, 0x0000);
 		snd_soc_component_update_bits(component,
 			RT5682_DAC_ADC_DIG_VOL1, 0x00c0, 0x0000);
 		break;
@@ -1637,6 +1659,23 @@
 static const struct snd_kcontrol_new rt5682_adcdat_pin_ctrl =
 	SOC_DAPM_ENUM("ADCDAT", rt5682_adcdat_pin_enum);
 
+static const unsigned int rt5682_hpo_sig_out_values[] = {
+	2,
+	7,
+};
+
+static const char * const rt5682_hpo_sig_out_mode[] = {
+	"Legacy",
+	"OneBit",
+};
+
+static SOC_VALUE_ENUM_SINGLE_DECL(rt5682_hpo_sig_out_enum,
+	RT5682_HP_LOGIC_CTRL_2, 0, RT5682_HP_LC2_SIG_SOUR1_MASK,
+	rt5682_hpo_sig_out_mode, rt5682_hpo_sig_out_values);
+
+static const struct snd_kcontrol_new rt5682_hpo_sig_demux =
+	SOC_DAPM_ENUM("HPO Signal Demux", rt5682_hpo_sig_out_enum);
+
 static const struct snd_soc_dapm_widget rt5682_dapm_widgets[] = {
 	SND_SOC_DAPM_SUPPLY("LDO2", RT5682_PWR_ANLG_3, RT5682_PWR_LDO2_BIT,
 		0, NULL, 0),
@@ -1820,6 +1859,10 @@
 	SND_SOC_DAPM_SWITCH("HPOR Playback", SND_SOC_NOPM, 0, 0,
 		&hpor_switch),
 
+	SND_SOC_DAPM_OUT_DRV("HPO Legacy", SND_SOC_NOPM, 0, 0, NULL, 0),
+	SND_SOC_DAPM_OUT_DRV("HPO OneBit", SND_SOC_NOPM, 0, 0, NULL, 0),
+	SND_SOC_DAPM_DEMUX("HPO Signal Demux", SND_SOC_NOPM, 0, 0, &rt5682_hpo_sig_demux),
+
 	/* CLK DET */
 	SND_SOC_DAPM_SUPPLY("CLKDET SYS", RT5682_CLK_DET,
 		RT5682_SYS_CLK_DET_SFT,	0, NULL, 0),
@@ -1987,10 +2030,19 @@
 	{"HP Amp", NULL, "Charge Pump"},
 	{"HP Amp", NULL, "CLKDET SYS"},
 	{"HP Amp", NULL, "Vref1"},
-	{"HPOL Playback", "Switch", "HP Amp"},
-	{"HPOR Playback", "Switch", "HP Amp"},
+
+	{"HPO Signal Demux", NULL, "HP Amp"},
+
+	{"HPO Legacy", "Legacy", "HPO Signal Demux"},
+	{"HPO OneBit", "OneBit", "HPO Signal Demux"},
+
+	{"HPOL Playback", "Switch", "HPO Legacy"},
+	{"HPOR Playback", "Switch", "HPO Legacy"},
+
 	{"HPOL", NULL, "HPOL Playback"},
 	{"HPOR", NULL, "HPOR Playback"},
+	{"HPOL", NULL, "HPO OneBit"},
+	{"HPOR", NULL, "HPO OneBit"},
 };
 
 static int rt5682_set_tdm_slot(struct snd_soc_dai *dai, unsigned int tx_mask,
@@ -2510,7 +2562,7 @@
 static bool rt5682_clk_check(struct rt5682_priv *rt5682)
 {
 	if (!rt5682->master[RT5682_AIF1]) {
-		dev_dbg(rt5682->component->dev, "sysclk/dai not set correctly\n");
+		dev_dbg(rt5682->i2c_dev, "sysclk/dai not set correctly\n");
 		return false;
 	}
 	return true;
@@ -2521,13 +2573,15 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
-	struct snd_soc_dapm_context *dapm =
-			snd_soc_component_get_dapm(component);
+	struct snd_soc_component *component;
+	struct snd_soc_dapm_context *dapm;
 
 	if (!rt5682_clk_check(rt5682))
 		return -EINVAL;
 
+	component = rt5682->component;
+	dapm = snd_soc_component_get_dapm(component);
+
 	snd_soc_dapm_mutex_lock(dapm);
 
 	snd_soc_dapm_force_enable_pin_unlocked(dapm, "MICBIAS");
@@ -2557,13 +2611,15 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
-	struct snd_soc_dapm_context *dapm =
-			snd_soc_component_get_dapm(component);
+	struct snd_soc_component *component;
+	struct snd_soc_dapm_context *dapm;
 
 	if (!rt5682_clk_check(rt5682))
 		return;
 
+	component = rt5682->component;
+	dapm = snd_soc_component_get_dapm(component);
+
 	snd_soc_dapm_mutex_lock(dapm);
 
 	snd_soc_dapm_disable_pin_unlocked(dapm, "MICBIAS");
@@ -2587,7 +2643,6 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
 	const char * const clk_name = clk_hw_get_name(hw);
 
 	if (!rt5682_clk_check(rt5682))
@@ -2597,7 +2652,7 @@
 	 */
 	if (rt5682->lrck[RT5682_AIF1] != CLK_48 &&
 	    rt5682->lrck[RT5682_AIF1] != CLK_44) {
-		dev_warn(component->dev, "%s: clk %s only support %d or %d Hz output\n",
+		dev_warn(rt5682->i2c_dev, "%s: clk %s only support %d or %d Hz output\n",
 			__func__, clk_name, CLK_44, CLK_48);
 		return 0;
 	}
@@ -2611,7 +2666,6 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
 	const char * const clk_name = clk_hw_get_name(hw);
 
 	if (!rt5682_clk_check(rt5682))
@@ -2621,7 +2675,7 @@
 	 * It will force to 48kHz if not both.
 	 */
 	if (rate != CLK_48 && rate != CLK_44) {
-		dev_warn(component->dev, "%s: clk %s only support %d or %d Hz output\n",
+		dev_warn(rt5682->i2c_dev, "%s: clk %s only support %d or %d Hz output\n",
 			__func__, clk_name, CLK_44, CLK_48);
 		rate = CLK_48;
 	}
@@ -2635,7 +2689,7 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_WCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
+	struct snd_soc_component *component;
 	struct clk_hw *parent_hw;
 	const char * const clk_name = clk_hw_get_name(hw);
 	int pre_div;
@@ -2644,6 +2698,8 @@
 	if (!rt5682_clk_check(rt5682))
 		return -EINVAL;
 
+	component = rt5682->component;
+
 	/*
 	 * Whether the wclk's parent clk (mclk) exists or not, please ensure
 	 * it is fixed or set to 48MHz before setting wclk rate. It's a
@@ -2653,12 +2709,12 @@
 	 */
 	parent_hw = clk_hw_get_parent(hw);
 	if (!parent_hw)
-		dev_warn(component->dev,
+		dev_warn(rt5682->i2c_dev,
 			"Parent mclk of wclk not acquired in driver. Please ensure mclk was provided as %d Hz.\n",
 			CLK_PLL2_FIN);
 
 	if (parent_rate != CLK_PLL2_FIN)
-		dev_warn(component->dev, "clk %s only support %d Hz input\n",
+		dev_warn(rt5682->i2c_dev, "clk %s only support %d Hz input\n",
 			clk_name, CLK_PLL2_FIN);
 
 	/*
@@ -2690,10 +2746,9 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_BCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
 	unsigned int bclks_per_wclk;
 
-	bclks_per_wclk = snd_soc_component_read(component, RT5682_TDM_TCON_CTRL);
+	regmap_read(rt5682->regmap, RT5682_TDM_TCON_CTRL, &bclks_per_wclk);
 
 	switch (bclks_per_wclk & RT5682_TDM_BCLK_MS1_MASK) {
 	case RT5682_TDM_BCLK_MS1_256:
@@ -2754,25 +2809,24 @@
 	struct rt5682_priv *rt5682 =
 		container_of(hw, struct rt5682_priv,
 			     dai_clks_hw[RT5682_DAI_BCLK_IDX]);
-	struct snd_soc_component *component = rt5682->component;
+	struct snd_soc_component *component;
 	struct snd_soc_dai *dai;
 	unsigned long factor;
 
 	if (!rt5682_clk_check(rt5682))
 		return -EINVAL;
 
+	component = rt5682->component;
+
 	factor = rt5682_bclk_get_factor(rate, parent_rate);
 
 	for_each_component_dais(component, dai)
 		if (dai->id == RT5682_AIF1)
-			break;
-	if (!dai) {
-		dev_err(component->dev, "dai %d not found in component\n",
-			RT5682_AIF1);
-		return -ENODEV;
-	}
+			return rt5682_set_bclk1_ratio(dai, factor);
 
-	return rt5682_set_bclk1_ratio(dai, factor);
+	dev_err(rt5682->i2c_dev, "dai %d not found in component\n",
+		RT5682_AIF1);
+	return -ENODEV;
 }
 
 static const struct clk_ops rt5682_dai_clk_ops[RT5682_DAI_NUM_CLKS] = {
@@ -2790,16 +2844,17 @@
 	},
 };
 
-static int rt5682_register_dai_clks(struct snd_soc_component *component)
+int rt5682_register_dai_clks(struct rt5682_priv *rt5682)
 {
-	struct device *dev = component->dev;
-	struct rt5682_priv *rt5682 = snd_soc_component_get_drvdata(component);
+	struct device *dev = rt5682->i2c_dev;
 	struct rt5682_platform_data *pdata = &rt5682->pdata;
 	struct clk_hw *dai_clk_hw;
 	int i, ret;
 
 	for (i = 0; i < RT5682_DAI_NUM_CLKS; ++i) {
 		struct clk_init_data init = { };
+		struct clk_parent_data parent_data;
+		const struct clk_hw *parent;
 
 		dai_clk_hw = &rt5682->dai_clks_hw[i];
 
@@ -2807,17 +2862,17 @@
 		case RT5682_DAI_WCLK_IDX:
 			/* Make MCLK the parent of WCLK */
 			if (rt5682->mclk) {
-				init.parent_data = &(struct clk_parent_data){
+				parent_data = (struct clk_parent_data){
 					.fw_name = "mclk",
 				};
+				init.parent_data = &parent_data;
 				init.num_parents = 1;
 			}
 			break;
 		case RT5682_DAI_BCLK_IDX:
 			/* Make WCLK the parent of BCLK */
-			init.parent_hws = &(const struct clk_hw *){
-				&rt5682->dai_clks_hw[RT5682_DAI_WCLK_IDX]
-			};
+			parent = &rt5682->dai_clks_hw[RT5682_DAI_WCLK_IDX];
+			init.parent_hws = &parent;
 			init.num_parents = 1;
 			break;
 		default:
@@ -2838,8 +2893,10 @@
 		}
 
 		if (dev->of_node) {
-			devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
+			ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
 						    dai_clk_hw);
+			if (ret)
+				return ret;
 		} else {
 			ret = devm_clk_hw_register_clkdev(dev, dai_clk_hw,
 							  init.name,
@@ -2851,6 +2908,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(rt5682_register_dai_clks);
 #endif /* CONFIG_COMMON_CLK */
 
 static int rt5682_probe(struct snd_soc_component *component)
@@ -2860,9 +2918,6 @@
 	unsigned long time;
 	struct snd_soc_dapm_context *dapm = &component->dapm;
 
-#ifdef CONFIG_COMMON_CLK
-	int ret;
-#endif
 	rt5682->component = component;
 
 	if (rt5682->is_sdw) {
@@ -2874,26 +2929,6 @@
 			dev_err(&slave->dev, "Initialization not complete, timed out\n");
 			return -ETIMEDOUT;
 		}
-	} else {
-#ifdef CONFIG_COMMON_CLK
-		/* Check if MCLK provided */
-		rt5682->mclk = devm_clk_get(component->dev, "mclk");
-		if (IS_ERR(rt5682->mclk)) {
-			if (PTR_ERR(rt5682->mclk) != -ENOENT) {
-				ret = PTR_ERR(rt5682->mclk);
-				return ret;
-			}
-			rt5682->mclk = NULL;
-		}
-
-		/* Register CCF DAI clock control */
-		ret = rt5682_register_dai_clks(component);
-		if (ret)
-			return ret;
-
-		/* Initial setup for CCF */
-		rt5682->lrck[RT5682_AIF1] = CLK_48;
-#endif
 	}
 
 	snd_soc_dapm_disable_pin(dapm, "MICBIAS");
@@ -2918,12 +2953,12 @@
 	if (rt5682->is_sdw)
 		return 0;
 
+	if (rt5682->irq)
+		disable_irq(rt5682->irq);
+
 	cancel_delayed_work_sync(&rt5682->jack_detect_work);
 	cancel_delayed_work_sync(&rt5682->jd_check_work);
-	if (rt5682->hs_jack && rt5682->jack_type == SND_JACK_HEADSET) {
-		snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
-			RT5682_MB1_PATH_MASK | RT5682_MB2_PATH_MASK,
-			RT5682_CTRL_MB1_REG | RT5682_CTRL_MB2_REG);
+	if (rt5682->hs_jack && (rt5682->jack_type & SND_JACK_HEADSET) == SND_JACK_HEADSET) {
 		val = snd_soc_component_read(component,
 				RT5682_CBJ_CTRL_2) & RT5682_JACK_TYPE_MASK;
 
@@ -2945,10 +2980,17 @@
 		/* enter SAR ADC power saving mode */
 		snd_soc_component_update_bits(component, RT5682_SAR_IL_CMD_1,
 			RT5682_SAR_BUTT_DET_MASK | RT5682_SAR_BUTDET_MODE_MASK |
-			RT5682_SAR_BUTDET_RST_MASK | RT5682_SAR_SEL_MB1_MB2_MASK, 0);
+			RT5682_SAR_SEL_MB1_MB2_MASK, 0);
+		usleep_range(5000, 6000);
+		snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
+			RT5682_MB1_PATH_MASK | RT5682_MB2_PATH_MASK,
+			RT5682_CTRL_MB1_REG | RT5682_CTRL_MB2_REG);
+		usleep_range(10000, 12000);
 		snd_soc_component_update_bits(component, RT5682_SAR_IL_CMD_1,
-			RT5682_SAR_BUTT_DET_MASK | RT5682_SAR_BUTDET_MODE_MASK | RT5682_SAR_BUTDET_RST_MASK,
-			RT5682_SAR_BUTT_DET_EN | RT5682_SAR_BUTDET_POW_SAV | RT5682_SAR_BUTDET_RST_NORMAL);
+			RT5682_SAR_BUTT_DET_MASK | RT5682_SAR_BUTDET_MODE_MASK,
+			RT5682_SAR_BUTT_DET_EN | RT5682_SAR_BUTDET_POW_SAV);
+		snd_soc_component_update_bits(component, RT5682_HP_CHARGE_PUMP_1,
+			RT5682_OSW_L_MASK | RT5682_OSW_R_MASK, 0);
 	}
 
 	regcache_cache_only(rt5682->regmap, true);
@@ -2966,10 +3008,11 @@
 	regcache_cache_only(rt5682->regmap, false);
 	regcache_sync(rt5682->regmap);
 
-	if (rt5682->hs_jack && rt5682->jack_type == SND_JACK_HEADSET) {
+	if (rt5682->hs_jack && (rt5682->jack_type & SND_JACK_HEADSET) == SND_JACK_HEADSET) {
 		snd_soc_component_update_bits(component, RT5682_SAR_IL_CMD_1,
 			RT5682_SAR_BUTDET_MODE_MASK | RT5682_SAR_SEL_MB1_MB2_MASK,
 			RT5682_SAR_BUTDET_POW_NORM | RT5682_SAR_SEL_MB1_MB2_AUTO);
+		usleep_range(5000, 6000);
 		snd_soc_component_update_bits(component, RT5682_CBJ_CTRL_1,
 			RT5682_MB1_PATH_MASK | RT5682_MB2_PATH_MASK,
 			RT5682_CTRL_MB1_FSM | RT5682_CTRL_MB2_FSM);
@@ -2977,8 +3020,12 @@
 			RT5682_PWR_CBJ, RT5682_PWR_CBJ);
 	}
 
+	rt5682->jack_type = 0;
 	mod_delayed_work(system_power_efficient_wq,
-		&rt5682->jack_detect_work, msecs_to_jiffies(250));
+		&rt5682->jack_detect_work, msecs_to_jiffies(0));
+
+	if (rt5682->irq)
+		enable_irq(rt5682->irq);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt5682.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt5682.h
@@ -375,6 +375,14 @@
 #define RT5682_R_VOL_MASK			(0x3f)
 #define RT5682_R_VOL_SFT			0
 
+/* Headphone Amp Control 2 (0x0003) */
+#define RT5682_HP_C2_DAC_AMP_MUTE_SFT		15
+#define RT5682_HP_C2_DAC_AMP_MUTE		(0x1 << 15)
+#define RT5682_HP_C2_DAC_L_EN_SFT		14
+#define RT5682_HP_C2_DAC_L_EN			(0x1 << 14)
+#define RT5682_HP_C2_DAC_R_EN_SFT		13
+#define RT5682_HP_C2_DAC_R_EN			(0x1 << 13)
+
 /*Headphone Amp L/R Analog Gain and Digital NG2 Gain Control (0x0005 0x0006)*/
 #define RT5682_G_HP				(0xf << 8)
 #define RT5682_G_HP_SFT				8
@@ -1265,6 +1273,10 @@
 #define RT5682_HPA_CP_BIAS_6UA			(0x3 << 2)
 
 /* Charge Pump Internal Register1 (0x0125) */
+#define RT5682_CP_SW_SIZE_MASK			(0x7 << 8)
+#define RT5682_CP_SW_SIZE_L			(0x4 << 8)
+#define RT5682_CP_SW_SIZE_M			(0x2 << 8)
+#define RT5682_CP_SW_SIZE_S			(0x1 << 8)
 #define RT5682_CP_CLK_HP_MASK			(0x3 << 4)
 #define RT5682_CP_CLK_HP_100KHZ			(0x0 << 4)
 #define RT5682_CP_CLK_HP_200KHZ			(0x1 << 4)
@@ -1315,6 +1327,14 @@
 #define RT5682_DEB_STO_DAC_MASK			(0x7 << 4)
 #define RT5682_DEB_80_MS			(0x0 << 4)
 
+/* HP Behavior Logic Control 2 (0x01db) */
+#define RT5682_HP_LC2_SIG_SOUR2_MASK		(0x1 << 4)
+#define RT5682_HP_LC2_SIG_SOUR2_REG		(0x1 << 4)
+#define RT5682_HP_LC2_SIG_SOUR2_DC_CAL		(0x0 << 4)
+#define RT5682_HP_LC2_SIG_SOUR1_MASK		(0x7)
+#define RT5682_HP_LC2_SIG_SOUR1_1BIT		(0x7)
+#define RT5682_HP_LC2_SIG_SOUR1_LEGA		(0x2)
+
 /* SAR ADC Inline Command Control 1 (0x0210) */
 #define RT5682_SAR_BUTT_DET_MASK		(0x1 << 15)
 #define RT5682_SAR_BUTT_DET_EN			(0x1 << 15)
@@ -1408,6 +1428,7 @@
 
 struct rt5682_priv {
 	struct snd_soc_component *component;
+	struct device *i2c_dev;
 	struct rt5682_platform_data pdata;
 	struct regmap *regmap;
 	struct regmap *sdw_regmap;
@@ -1441,6 +1462,7 @@
 	int pll_out[RT5682_PLLS];
 
 	int jack_type;
+	int irq;
 	int irq_work_delay_time;
 };
 
@@ -1451,7 +1473,6 @@
 
 void rt5682_apply_patch_list(struct rt5682_priv *rt5682, struct device *dev);
 
-int rt5682_headset_detect(struct snd_soc_component *component, int jack_insert);
 void rt5682_jack_detect_handler(struct work_struct *work);
 
 bool rt5682_volatile_register(struct device *dev, unsigned int reg);
@@ -1462,6 +1483,8 @@
 void rt5682_reset(struct rt5682_priv *rt5682);
 int rt5682_parse_dt(struct rt5682_priv *rt5682, struct device *dev);
 
+int rt5682_register_dai_clks(struct rt5682_priv *rt5682);
+
 #define RT5682_REG_NUM 318
 extern const struct reg_default rt5682_reg[RT5682_REG_NUM];
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt700-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt700-sdw.c
@@ -13,6 +13,7 @@
 #include <linux/soundwire/sdw_type.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/module.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <sound/soc.h>
 #include "rt700.h"
@@ -463,11 +464,14 @@
 {
 	struct rt700_priv *rt700 = dev_get_drvdata(&slave->dev);
 
-	if (rt700 && rt700->hw_init) {
+	if (rt700->hw_init) {
 		cancel_delayed_work_sync(&rt700->jack_detect_work);
 		cancel_delayed_work_sync(&rt700->jack_btn_check_work);
 	}
 
+	if (rt700->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt700.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt700.c
@@ -162,7 +162,7 @@
 	if (!rt700->hs_jack)
 		return;
 
-	if (!rt700->component->card->instantiated)
+	if (!rt700->component->card || !rt700->component->card->instantiated)
 		return;
 
 	reg = RT700_VERB_GET_PIN_SENSE | RT700_HP_OUT;
@@ -315,17 +315,27 @@
 	struct snd_soc_jack *hs_jack, void *data)
 {
 	struct rt700_priv *rt700 = snd_soc_component_get_drvdata(component);
+	int ret;
 
 	rt700->hs_jack = hs_jack;
 
-	if (!rt700->hw_init) {
-		dev_dbg(&rt700->slave->dev,
-			"%s hw_init not ready yet\n", __func__);
+	ret = pm_runtime_resume_and_get(component->dev);
+	if (ret < 0) {
+		if (ret != -EACCES) {
+			dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret);
+			return ret;
+		}
+
+		/* pm_runtime not enabled yet */
+		dev_dbg(component->dev,	"%s: skipping jack init for now\n", __func__);
 		return 0;
 	}
 
 	rt700_jack_init(rt700);
 
+	pm_runtime_mark_last_busy(component->dev);
+	pm_runtime_put_autosuspend(component->dev);
+
 	return 0;
 }
 
@@ -1005,7 +1015,7 @@
 static const struct snd_soc_dai_ops rt700_ops = {
 	.hw_params	= rt700_pcm_hw_params,
 	.hw_free	= rt700_pcm_hw_free,
-	.set_sdw_stream	= rt700_set_sdw_stream,
+	.set_stream	= rt700_set_sdw_stream,
 	.shutdown	= rt700_shutdown,
 };
 
@@ -1114,6 +1124,11 @@
 
 	mutex_init(&rt700->disable_irq_lock);
 
+	INIT_DELAYED_WORK(&rt700->jack_detect_work,
+			  rt700_jack_detect_handler);
+	INIT_DELAYED_WORK(&rt700->jack_btn_check_work,
+			  rt700_btn_check_handler);
+
 	/*
 	 * Mark hw_init to false
 	 * HW init will be performed when device reports present
@@ -1208,13 +1223,6 @@
 	/* Finish Initial Settings, set power to D3 */
 	regmap_write(rt700->regmap, RT700_SET_AUDIO_POWER_STATE, AC_PWRST_D3);
 
-	if (!rt700->first_hw_init) {
-		INIT_DELAYED_WORK(&rt700->jack_detect_work,
-			rt700_jack_detect_handler);
-		INIT_DELAYED_WORK(&rt700->jack_btn_check_work,
-			rt700_btn_check_handler);
-	}
-
 	/*
 	 * if set_jack callback occurred early than io_init,
 	 * we set up the jack detection function now
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt711-sdca-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt711-sdca-sdw.c
@@ -11,6 +11,7 @@
 #include <linux/mod_devicetable.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/module.h>
+#include <linux/pm_runtime.h>
 
 #include "rt711-sdca.h"
 #include "rt711-sdca-sdw.h"
@@ -229,7 +230,7 @@
 	}
 
 	/* set the timeout values */
-	prop->clk_stop_timeout = 20;
+	prop->clk_stop_timeout = 700;
 
 	/* wake-up event */
 	prop->wake_capable = 1;
@@ -364,11 +365,17 @@
 {
 	struct rt711_sdca_priv *rt711 = dev_get_drvdata(&slave->dev);
 
-	if (rt711 && rt711->hw_init) {
+	if (rt711->hw_init) {
 		cancel_delayed_work_sync(&rt711->jack_detect_work);
 		cancel_delayed_work_sync(&rt711->jack_btn_check_work);
 	}
 
+	if (rt711->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	mutex_destroy(&rt711->calibrate_mutex);
+	mutex_destroy(&rt711->disable_irq_lock);
+
 	return 0;
 }
 
@@ -435,8 +442,16 @@
 	if (!rt711->first_hw_init)
 		return 0;
 
-	if (!slave->unattach_request)
+	if (!slave->unattach_request) {
+		mutex_lock(&rt711->disable_irq_lock);
+		if (rt711->disable_irq == true) {
+			sdw_write_no_pm(slave, SDW_SCP_SDCA_INTMASK1, SDW_SCP_SDCA_INTMASK_SDCA_0);
+			sdw_write_no_pm(slave, SDW_SCP_SDCA_INTMASK2, SDW_SCP_SDCA_INTMASK_SDCA_8);
+			rt711->disable_irq = false;
+		}
+		mutex_unlock(&rt711->disable_irq_lock);
 		goto regmap_sync;
+	}
 
 	time = wait_for_completion_timeout(&slave->initialization_complete,
 				msecs_to_jiffies(RT711_PROBE_TIMEOUT));
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt711-sdca.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt711-sdca.c
@@ -34,7 +34,7 @@
 
 	ret = regmap_write(regmap, addr, value);
 	if (ret < 0)
-		dev_err(rt711->component->dev,
+		dev_err(&rt711->slave->dev,
 			"Failed to set private value: %06x <= %04x ret=%d\n",
 			addr, value, ret);
 
@@ -50,7 +50,7 @@
 
 	ret = regmap_read(regmap, addr, value);
 	if (ret < 0)
-		dev_err(rt711->component->dev,
+		dev_err(&rt711->slave->dev,
 			"Failed to get private value: %06x => %04x ret=%d\n",
 			addr, *value, ret);
 
@@ -294,7 +294,7 @@
 	if (!rt711->hs_jack)
 		return;
 
-	if (!rt711->component->card->instantiated)
+	if (!rt711->component->card || !rt711->component->card->instantiated)
 		return;
 
 	/* SDW_SCP_SDCA_INT_SDCA_0 is used for jack detection */
@@ -487,16 +487,27 @@
 	struct snd_soc_jack *hs_jack, void *data)
 {
 	struct rt711_sdca_priv *rt711 = snd_soc_component_get_drvdata(component);
+	int ret;
 
 	rt711->hs_jack = hs_jack;
 
-	if (!rt711->hw_init) {
-		dev_dbg(&rt711->slave->dev,
-			"%s hw_init not ready yet\n", __func__);
+	ret = pm_runtime_resume_and_get(component->dev);
+	if (ret < 0) {
+		if (ret != -EACCES) {
+			dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret);
+			return ret;
+		}
+
+		/* pm_runtime not enabled yet */
+		dev_dbg(component->dev,	"%s: skipping jack init for now\n", __func__);
 		return 0;
 	}
 
 	rt711_sdca_jack_init(rt711);
+
+	pm_runtime_mark_last_busy(component->dev);
+	pm_runtime_put_autosuspend(component->dev);
+
 	return 0;
 }
 
@@ -1190,14 +1201,6 @@
 	return 0;
 }
 
-static void rt711_sdca_remove(struct snd_soc_component *component)
-{
-	struct rt711_sdca_priv *rt711 = snd_soc_component_get_drvdata(component);
-
-	regcache_cache_only(rt711->regmap, true);
-	regcache_cache_only(rt711->mbq_regmap, true);
-}
-
 static const struct snd_soc_component_driver soc_sdca_dev_rt711 = {
 	.probe = rt711_sdca_probe,
 	.controls = rt711_sdca_snd_controls,
@@ -1207,7 +1210,7 @@
 	.dapm_routes = rt711_sdca_audio_map,
 	.num_dapm_routes = ARRAY_SIZE(rt711_sdca_audio_map),
 	.set_jack = rt711_sdca_set_jack_detect,
-	.remove = rt711_sdca_remove,
+	.endianness = 1,
 };
 
 static int rt711_sdca_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream,
@@ -1358,7 +1361,7 @@
 static const struct snd_soc_dai_ops rt711_sdca_ops = {
 	.hw_params	= rt711_sdca_pcm_hw_params,
 	.hw_free	= rt711_sdca_pcm_hw_free,
-	.set_sdw_stream	= rt711_sdca_set_sdw_stream,
+	.set_stream	= rt711_sdca_set_sdw_stream,
 	.shutdown	= rt711_sdca_shutdown,
 };
 
@@ -1411,8 +1414,12 @@
 	rt711->regmap = regmap;
 	rt711->mbq_regmap = mbq_regmap;
 
+	mutex_init(&rt711->calibrate_mutex);
 	mutex_init(&rt711->disable_irq_lock);
 
+	INIT_DELAYED_WORK(&rt711->jack_detect_work, rt711_sdca_jack_detect_handler);
+	INIT_DELAYED_WORK(&rt711->jack_btn_check_work, rt711_sdca_btn_check_handler);
+
 	/*
 	 * Mark hw_init to false
 	 * HW init will be performed when device reports present
@@ -1544,14 +1551,6 @@
 	rt711_sdca_index_update_bits(rt711, RT711_VENDOR_HDA_CTL,
 		RT711_PUSH_BTN_INT_CTL0, 0x20, 0x00);
 
-	if (!rt711->first_hw_init) {
-		INIT_DELAYED_WORK(&rt711->jack_detect_work,
-			rt711_sdca_jack_detect_handler);
-		INIT_DELAYED_WORK(&rt711->jack_btn_check_work,
-			rt711_sdca_btn_check_handler);
-		mutex_init(&rt711->calibrate_mutex);
-	}
-
 	/* calibration */
 	ret = rt711_sdca_calibration(rt711);
 	if (ret < 0)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt711-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt711-sdw.c
@@ -13,6 +13,7 @@
 #include <linux/soundwire/sdw_type.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/module.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <sound/soc.h>
 #include "rt711.h"
@@ -464,12 +465,18 @@
 {
 	struct rt711_priv *rt711 = dev_get_drvdata(&slave->dev);
 
-	if (rt711 && rt711->hw_init) {
+	if (rt711->hw_init) {
 		cancel_delayed_work_sync(&rt711->jack_detect_work);
 		cancel_delayed_work_sync(&rt711->jack_btn_check_work);
 		cancel_work_sync(&rt711->calibration_work);
 	}
 
+	if (rt711->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	mutex_destroy(&rt711->calibrate_mutex);
+	mutex_destroy(&rt711->disable_irq_lock);
+
 	return 0;
 }
 
@@ -534,8 +541,15 @@
 	if (!rt711->first_hw_init)
 		return 0;
 
-	if (!slave->unattach_request)
+	if (!slave->unattach_request) {
+		mutex_lock(&rt711->disable_irq_lock);
+		if (rt711->disable_irq == true) {
+			sdw_write_no_pm(slave, SDW_SCP_INTMASK1, SDW_SCP_INT1_IMPL_DEF);
+			rt711->disable_irq = false;
+		}
+		mutex_unlock(&rt711->disable_irq_lock);
 		goto regmap_sync;
+	}
 
 	time = wait_for_completion_timeout(&slave->initialization_complete,
 				msecs_to_jiffies(RT711_PROBE_TIMEOUT));
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt711.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt711.c
@@ -242,7 +242,7 @@
 	if (!rt711->hs_jack)
 		return;
 
-	if (!rt711->component->card->instantiated)
+	if (!rt711->component->card || !rt711->component->card->instantiated)
 		return;
 
 	reg = RT711_VERB_GET_PIN_SENSE | RT711_HP_OUT;
@@ -450,17 +450,27 @@
 	struct snd_soc_jack *hs_jack, void *data)
 {
 	struct rt711_priv *rt711 = snd_soc_component_get_drvdata(component);
+	int ret;
 
 	rt711->hs_jack = hs_jack;
 
-	if (!rt711->hw_init) {
-		dev_dbg(&rt711->slave->dev,
-			"%s hw_init not ready yet\n", __func__);
+	ret = pm_runtime_resume_and_get(component->dev);
+	if (ret < 0) {
+		if (ret != -EACCES) {
+			dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret);
+			return ret;
+		}
+
+		/* pm_runtime not enabled yet */
+		dev_dbg(component->dev,	"%s: skipping jack init for now\n", __func__);
 		return 0;
 	}
 
 	rt711_jack_init(rt711);
 
+	pm_runtime_mark_last_busy(component->dev);
+	pm_runtime_put_autosuspend(component->dev);
+
 	return 0;
 }
 
@@ -925,13 +935,6 @@
 	return 0;
 }
 
-static void rt711_remove(struct snd_soc_component *component)
-{
-	struct rt711_priv *rt711 = snd_soc_component_get_drvdata(component);
-
-	regcache_cache_only(rt711->regmap, true);
-}
-
 static const struct snd_soc_component_driver soc_codec_dev_rt711 = {
 	.probe = rt711_probe,
 	.set_bias_level = rt711_set_bias_level,
@@ -942,7 +945,7 @@
 	.dapm_routes = rt711_audio_map,
 	.num_dapm_routes = ARRAY_SIZE(rt711_audio_map),
 	.set_jack = rt711_set_jack_detect,
-	.remove = rt711_remove,
+	.endianness = 1,
 };
 
 static int rt711_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream,
@@ -1089,7 +1092,7 @@
 static const struct snd_soc_dai_ops rt711_ops = {
 	.hw_params	= rt711_pcm_hw_params,
 	.hw_free	= rt711_pcm_hw_free,
-	.set_sdw_stream	= rt711_set_sdw_stream,
+	.set_stream	= rt711_set_sdw_stream,
 	.shutdown	= rt711_shutdown,
 };
 
@@ -1196,8 +1199,13 @@
 	rt711->sdw_regmap = sdw_regmap;
 	rt711->regmap = regmap;
 
+	mutex_init(&rt711->calibrate_mutex);
 	mutex_init(&rt711->disable_irq_lock);
 
+	INIT_DELAYED_WORK(&rt711->jack_detect_work, rt711_jack_detect_handler);
+	INIT_DELAYED_WORK(&rt711->jack_btn_check_work, rt711_btn_check_handler);
+	INIT_WORK(&rt711->calibration_work, rt711_calibration_work);
+
 	/*
 	 * Mark hw_init to false
 	 * HW init will be performed when device reports present
@@ -1305,15 +1313,8 @@
 
 	if (rt711->first_hw_init)
 		rt711_calibration(rt711);
-	else {
-		INIT_DELAYED_WORK(&rt711->jack_detect_work,
-			rt711_jack_detect_handler);
-		INIT_DELAYED_WORK(&rt711->jack_btn_check_work,
-			rt711_btn_check_handler);
-		mutex_init(&rt711->calibrate_mutex);
-		INIT_WORK(&rt711->calibration_work, rt711_calibration_work);
+	else
 		schedule_work(&rt711->calibration_work);
-	}
 
 	/*
 	 * if set_jack callback occurred early than io_init,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt715-sdca-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt715-sdca-sdw.c
@@ -13,6 +13,7 @@
 #include <linux/soundwire/sdw_type.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/module.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <sound/soc.h>
 #include "rt715-sdca.h"
@@ -166,7 +167,7 @@
 	}
 
 	/* set the timeout values */
-	prop->clk_stop_timeout = 20;
+	prop->clk_stop_timeout = 200;
 
 	return 0;
 }
@@ -195,6 +196,16 @@
 	return rt715_sdca_init(&slave->dev, mbq_regmap, regmap, slave);
 }
 
+static int rt715_sdca_sdw_remove(struct sdw_slave *slave)
+{
+	struct rt715_sdca_priv *rt715 = dev_get_drvdata(&slave->dev);
+
+	if (rt715->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	return 0;
+}
+
 static const struct sdw_device_id rt715_sdca_id[] = {
 	SDW_SLAVE_ENTRY_EXT(0x025d, 0x715, 0x3, 0x1, 0),
 	SDW_SLAVE_ENTRY_EXT(0x025d, 0x714, 0x3, 0x1, 0),
@@ -269,6 +280,7 @@
 		.pm = &rt715_pm,
 	},
 	.probe = rt715_sdca_sdw_probe,
+	.remove = rt715_sdca_sdw_remove,
 	.ops = &rt715_sdca_slave_ops,
 	.id_table = rt715_sdca_id,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt715-sdca.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt715-sdca.c
@@ -315,7 +315,7 @@
 	return 0;
 }
 
-static const DECLARE_TLV_DB_SCALE(in_vol_tlv, -17625, 375, 0);
+static const DECLARE_TLV_DB_SCALE(in_vol_tlv, -1725, 75, 0);
 static const DECLARE_TLV_DB_SCALE(mic_vol_tlv, 0, 1000, 0);
 
 static int rt715_sdca_get_volsw(struct snd_kcontrol *kcontrol,
@@ -476,7 +476,7 @@
 			RT715_SDCA_FU_VOL_CTRL, CH_01),
 		SDW_SDCA_CTL(FUN_MIC_ARRAY, RT715_SDCA_FU_ADC7_27_VOL,
 			RT715_SDCA_FU_VOL_CTRL, CH_02),
-			0x2f, 0x7f, 0,
+			0x2f, 0x3f, 0,
 		rt715_sdca_set_amp_gain_get, rt715_sdca_set_amp_gain_put,
 		in_vol_tlv),
 	RT715_SDCA_EXT_TLV("FU02 Capture Volume",
@@ -484,13 +484,13 @@
 			RT715_SDCA_FU_VOL_CTRL, CH_01),
 		rt715_sdca_set_amp_gain_4ch_get,
 		rt715_sdca_set_amp_gain_4ch_put,
-		in_vol_tlv, 4, 0x7f),
+		in_vol_tlv, 4, 0x3f),
 	RT715_SDCA_EXT_TLV("FU06 Capture Volume",
 		SDW_SDCA_CTL(FUN_MIC_ARRAY, RT715_SDCA_FU_ADC10_11_VOL,
 			RT715_SDCA_FU_VOL_CTRL, CH_01),
 		rt715_sdca_set_amp_gain_4ch_get,
 		rt715_sdca_set_amp_gain_4ch_put,
-		in_vol_tlv, 4, 0x7f),
+		in_vol_tlv, 4, 0x3f),
 	/* MIC Boost Control */
 	RT715_SDCA_BOOST_EXT_TLV("FU0E Boost",
 		SDW_SDCA_CTL(FUN_MIC_ARRAY, RT715_SDCA_FU_DMIC_GAIN_EN,
@@ -938,7 +938,7 @@
 static const struct snd_soc_dai_ops rt715_sdca_ops = {
 	.hw_params	= rt715_sdca_pcm_hw_params,
 	.hw_free	= rt715_sdca_pcm_hw_free,
-	.set_sdw_stream	= rt715_sdca_set_sdw_stream,
+	.set_stream	= rt715_sdca_set_sdw_stream,
 	.shutdown	= rt715_sdca_shutdown,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt715-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt715-sdw.c
@@ -14,6 +14,7 @@
 #include <linux/soundwire/sdw_type.h>
 #include <linux/soundwire/sdw_registers.h>
 #include <linux/module.h>
+#include <linux/pm_runtime.h>
 #include <linux/of.h>
 #include <linux/regmap.h>
 #include <sound/soc.h>
@@ -110,6 +111,7 @@
 	case 0x839d:
 	case 0x83a7:
 	case 0x83a9:
+	case 0x752001:
 	case 0x752039:
 		return true;
 	default:
@@ -514,6 +516,16 @@
 	return 0;
 }
 
+static int rt715_sdw_remove(struct sdw_slave *slave)
+{
+	struct rt715_priv *rt715 = dev_get_drvdata(&slave->dev);
+
+	if (rt715->first_hw_init)
+		pm_runtime_disable(&slave->dev);
+
+	return 0;
+}
+
 static const struct sdw_device_id rt715_id[] = {
 	SDW_SLAVE_ENTRY_EXT(0x025d, 0x714, 0x2, 0, 0),
 	SDW_SLAVE_ENTRY_EXT(0x025d, 0x715, 0x2, 0, 0),
@@ -575,6 +587,7 @@
 		   .pm = &rt715_pm,
 		   },
 	.probe = rt715_sdw_probe,
+	.remove = rt715_sdw_remove,
 	.ops = &rt715_slave_ops,
 	.id_table = rt715_id,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/rt715.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/rt715.c
@@ -909,7 +909,7 @@
 static const struct snd_soc_dai_ops rt715_ops = {
 	.hw_params	= rt715_pcm_hw_params,
 	.hw_free	= rt715_pcm_hw_free,
-	.set_sdw_stream	= rt715_set_sdw_stream,
+	.set_stream	= rt715_set_sdw_stream,
 	.shutdown	= rt715_shutdown,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/sdw-mockup.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/sdw-mockup.c
@@ -138,7 +138,7 @@
 static const struct snd_soc_dai_ops sdw_mockup_ops = {
 	.hw_params	= sdw_mockup_pcm_hw_params,
 	.hw_free	= sdw_mockup_pcm_hw_free,
-	.set_sdw_stream	= sdw_mockup_set_sdw_stream,
+	.set_stream	= sdw_mockup_set_sdw_stream,
 	.shutdown	= sdw_mockup_shutdown,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/sgtl5000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/sgtl5000.c
@@ -1797,6 +1797,10 @@
 {
 	struct sgtl5000_priv *sgtl5000 = i2c_get_clientdata(client);
 
+	regmap_write(sgtl5000->regmap, SGTL5000_CHIP_CLK_CTRL, SGTL5000_CHIP_CLK_CTRL_DEFAULT);
+	regmap_write(sgtl5000->regmap, SGTL5000_CHIP_DIG_POWER, SGTL5000_DIG_POWER_DEFAULT);
+	regmap_write(sgtl5000->regmap, SGTL5000_CHIP_ANA_POWER, SGTL5000_ANA_POWER_DEFAULT);
+
 	clk_disable_unprepare(sgtl5000->mclk);
 	regulator_bulk_disable(sgtl5000->num_supplies, sgtl5000->supplies);
 	regulator_bulk_free(sgtl5000->num_supplies, sgtl5000->supplies);
@@ -1804,6 +1808,11 @@
 	return 0;
 }
 
+static void sgtl5000_i2c_shutdown(struct i2c_client *client)
+{
+	sgtl5000_i2c_remove(client);
+}
+
 static const struct i2c_device_id sgtl5000_id[] = {
 	{"sgtl5000", 0},
 	{},
@@ -1824,6 +1833,7 @@
 	},
 	.probe = sgtl5000_i2c_probe,
 	.remove = sgtl5000_i2c_remove,
+	.shutdown = sgtl5000_i2c_shutdown,
 	.id_table = sgtl5000_id,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/sgtl5000.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/sgtl5000.h
@@ -80,6 +80,7 @@
 /*
  * SGTL5000_CHIP_DIG_POWER
  */
+#define SGTL5000_DIG_POWER_DEFAULT		0x0000
 #define SGTL5000_ADC_EN				0x0040
 #define SGTL5000_DAC_EN				0x0020
 #define SGTL5000_DAP_POWERUP			0x0010
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/ssm2602.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/ssm2602.c
@@ -53,6 +53,18 @@
 	{ .reg = 0x09, .def = 0x0000 }
 };
 
+/*
+ * ssm2602 register patch
+ * Workaround for playback distortions after power up: activates digital
+ * core, and then powers on output, DAC, and whole chip at the same time
+ */
+
+static const struct reg_sequence ssm2602_patch[] = {
+	{ SSM2602_ACTIVE, 0x01 },
+	{ SSM2602_PWR,    0x07 },
+	{ SSM2602_RESET,  0x00 },
+};
+
 
 /*Appending several "None"s just for OSS mixer use*/
 static const char *ssm2602_input_select[] = {
@@ -589,6 +601,9 @@
 		return ret;
 	}
 
+	regmap_register_patch(ssm2602->regmap, ssm2602_patch,
+			      ARRAY_SIZE(ssm2602_patch));
+
 	/* set the update bits */
 	regmap_update_bits(ssm2602->regmap, SSM2602_LINVOL,
 			    LINVOL_LRIN_BOTH, LINVOL_LRIN_BOTH);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tas2552.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tas2552.c
@@ -2,7 +2,8 @@
 /*
  * tas2552.c - ALSA SoC Texas Instruments TAS2552 Mono Audio Amplifier
  *
- * Copyright (C) 2014 Texas Instruments Incorporated -  https://www.ti.com
+ * Copyright (C) 2014 - 2024 Texas Instruments Incorporated -
+ *	https://www.ti.com
  *
  * Author: Dan Murphy <dmurphy@ti.com>
  */
@@ -119,12 +120,14 @@
 			 &tas2552_input_mux_control),
 
 	SND_SOC_DAPM_AIF_IN("DAC IN", "DAC Playback", 0, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_AIF_OUT("ASI OUT", "DAC Capture", 0, SND_SOC_NOPM, 0, 0),
 	SND_SOC_DAPM_DAC("DAC", NULL, SND_SOC_NOPM, 0, 0),
 	SND_SOC_DAPM_OUT_DRV("ClassD", TAS2552_CFG_2, 7, 0, NULL, 0),
 	SND_SOC_DAPM_SUPPLY("PLL", TAS2552_CFG_2, 3, 0, NULL, 0),
 	SND_SOC_DAPM_POST("Post Event", tas2552_post_event),
 
-	SND_SOC_DAPM_OUTPUT("OUT")
+	SND_SOC_DAPM_OUTPUT("OUT"),
+	SND_SOC_DAPM_INPUT("DMIC")
 };
 
 static const struct snd_soc_dapm_route tas2552_audio_map[] = {
@@ -134,6 +137,7 @@
 	{"ClassD", NULL, "Input selection"},
 	{"OUT", NULL, "ClassD"},
 	{"ClassD", NULL, "PLL"},
+	{"ASI OUT", NULL, "DMIC"}
 };
 
 #ifdef CONFIG_PM
@@ -536,6 +540,13 @@
 			.channels_min = 2,
 			.channels_max = 2,
 			.rates = SNDRV_PCM_RATE_8000_192000,
+			.formats = TAS2552_FORMATS,
+		},
+		.capture = {
+			.stream_name = "Capture",
+			.channels_min = 2,
+			.channels_max = 2,
+			.rates = SNDRV_PCM_RATE_8000_192000,
 			.formats = TAS2552_FORMATS,
 		},
 		.ops = &tas2552_speaker_dai_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tas2764.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tas2764.c
@@ -34,6 +34,9 @@
 	
 	int v_sense_slot;
 	int i_sense_slot;
+
+	bool dac_powered;
+	bool unmuted;
 };
 
 static void tas2764_reset(struct tas2764_priv *tas2764)
@@ -42,40 +45,30 @@
 		gpiod_set_value_cansleep(tas2764->reset_gpio, 0);
 		msleep(20);
 		gpiod_set_value_cansleep(tas2764->reset_gpio, 1);
+		usleep_range(1000, 2000);
 	}
 
 	snd_soc_component_write(tas2764->component, TAS2764_SW_RST,
 				TAS2764_RST);
+	usleep_range(1000, 2000);
 }
 
-static int tas2764_set_bias_level(struct snd_soc_component *component,
-				 enum snd_soc_bias_level level)
+static int tas2764_update_pwr_ctrl(struct tas2764_priv *tas2764)
 {
-	struct tas2764_priv *tas2764 = snd_soc_component_get_drvdata(component);
+	struct snd_soc_component *component = tas2764->component;
+	unsigned int val;
+	int ret;
 
-	switch (level) {
-	case SND_SOC_BIAS_ON:
-		snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-					      TAS2764_PWR_CTRL_MASK,
-					      TAS2764_PWR_CTRL_ACTIVE);
-		break;
-	case SND_SOC_BIAS_STANDBY:
-	case SND_SOC_BIAS_PREPARE:
-		snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-					      TAS2764_PWR_CTRL_MASK,
-					      TAS2764_PWR_CTRL_MUTE);
-		break;
-	case SND_SOC_BIAS_OFF:
-		snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-					      TAS2764_PWR_CTRL_MASK,
-					      TAS2764_PWR_CTRL_SHUTDOWN);
-		break;
+	if (tas2764->dac_powered)
+		val = tas2764->unmuted ?
+			TAS2764_PWR_CTRL_ACTIVE : TAS2764_PWR_CTRL_MUTE;
+	else
+		val = TAS2764_PWR_CTRL_SHUTDOWN;
 
-	default:
-		dev_err(tas2764->dev,
-				"wrong power level setting %d\n", level);
-		return -EINVAL;
-	}
+	ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
+					    TAS2764_PWR_CTRL_MASK, val);
+	if (ret < 0)
+		return ret;
 
 	return 0;
 }
@@ -107,12 +100,12 @@
 	struct tas2764_priv *tas2764 = snd_soc_component_get_drvdata(component);
 	int ret;
 
-	if (tas2764->sdz_gpio)
+	if (tas2764->sdz_gpio) {
 		gpiod_set_value_cansleep(tas2764->sdz_gpio, 1);
+		usleep_range(1000, 2000);
+	}
 
-	ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-					    TAS2764_PWR_CTRL_MASK,
-					    TAS2764_PWR_CTRL_ACTIVE);
+	ret = tas2764_update_pwr_ctrl(tas2764);
 
 	if (ret < 0)
 		return ret;
@@ -131,7 +124,8 @@
 };
 
 static SOC_ENUM_SINGLE_DECL(
-	tas2764_ASI1_src_enum, TAS2764_TDM_CFG2, 4, tas2764_ASI1_src);
+	tas2764_ASI1_src_enum, TAS2764_TDM_CFG2, TAS2764_TDM_CFG2_SCFG_SHIFT,
+	tas2764_ASI1_src);
 
 static const struct snd_kcontrol_new tas2764_asi1_mux =
 	SOC_DAPM_ENUM("ASI1 Source", tas2764_ASI1_src_enum);
@@ -145,14 +139,12 @@
 
 	switch (event) {
 	case SND_SOC_DAPM_POST_PMU:
-		ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-						    TAS2764_PWR_CTRL_MASK,
-						    TAS2764_PWR_CTRL_MUTE);
+		tas2764->dac_powered = true;
+		ret = tas2764_update_pwr_ctrl(tas2764);
 		break;
 	case SND_SOC_DAPM_PRE_PMD:
-		ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-						    TAS2764_PWR_CTRL_MASK,
-						    TAS2764_PWR_CTRL_SHUTDOWN);
+		tas2764->dac_powered = false;
+		ret = tas2764_update_pwr_ctrl(tas2764);
 		break;
 	default:
 		dev_err(tas2764->dev, "Unsupported event\n");
@@ -197,17 +189,11 @@
 
 static int tas2764_mute(struct snd_soc_dai *dai, int mute, int direction)
 {
-	struct snd_soc_component *component = dai->component;
-	int ret;
-
-	ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-					    TAS2764_PWR_CTRL_MASK,
-					    mute ? TAS2764_PWR_CTRL_MUTE : 0);
-
-	if (ret < 0)
-		return ret;
+	struct tas2764_priv *tas2764 =
+			snd_soc_component_get_drvdata(dai->component);
 
-	return 0;
+	tas2764->unmuted = !mute;
+	return tas2764_update_pwr_ctrl(tas2764);
 }
 
 static int tas2764_set_bitwidth(struct tas2764_priv *tas2764, int bitwidth)
@@ -329,20 +315,24 @@
 {
 	struct snd_soc_component *component = dai->component;
 	struct tas2764_priv *tas2764 = snd_soc_component_get_drvdata(component);
-	u8 tdm_rx_start_slot = 0, asi_cfg_1 = 0;
-	int iface;
+	u8 tdm_rx_start_slot = 0, asi_cfg_0 = 0, asi_cfg_1 = 0, asi_cfg_4 = 0;
 	int ret;
 
 	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_IF:
+		asi_cfg_0 ^= TAS2764_TDM_CFG0_FRAME_START;
+		fallthrough;
 	case SND_SOC_DAIFMT_NB_NF:
 		asi_cfg_1 = TAS2764_TDM_CFG1_RX_RISING;
+		asi_cfg_4 = TAS2764_TDM_CFG4_TX_FALLING;
 		break;
+	case SND_SOC_DAIFMT_IB_IF:
+		asi_cfg_0 ^= TAS2764_TDM_CFG0_FRAME_START;
+		fallthrough;
 	case SND_SOC_DAIFMT_IB_NF:
 		asi_cfg_1 = TAS2764_TDM_CFG1_RX_FALLING;
+		asi_cfg_4 = TAS2764_TDM_CFG4_TX_RISING;
 		break;
-	default:
-		dev_err(tas2764->dev, "ASI format Inverse is not found\n");
-		return -EINVAL;
 	}
 
 	ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG1,
@@ -351,15 +341,21 @@
 	if (ret < 0)
 		return ret;
 
+	ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG4,
+					    TAS2764_TDM_CFG4_TX_MASK,
+					    asi_cfg_4);
+	if (ret < 0)
+		return ret;
+
 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
 	case SND_SOC_DAIFMT_I2S:
+		asi_cfg_0 ^= TAS2764_TDM_CFG0_FRAME_START;
+		fallthrough;
 	case SND_SOC_DAIFMT_DSP_A:
-		iface = TAS2764_TDM_CFG2_SCFG_I2S;
 		tdm_rx_start_slot = 1;
 		break;
 	case SND_SOC_DAIFMT_DSP_B:
 	case SND_SOC_DAIFMT_LEFT_J:
-		iface = TAS2764_TDM_CFG2_SCFG_LEFT_J;
 		tdm_rx_start_slot = 0;
 		break;
 	default:
@@ -368,14 +364,15 @@
 		return -EINVAL;
 	}
 
-	ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG1,
-					    TAS2764_TDM_CFG1_MASK,
-					    (tdm_rx_start_slot << TAS2764_TDM_CFG1_51_SHIFT));
+	ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG0,
+					    TAS2764_TDM_CFG0_FRAME_START,
+					    asi_cfg_0);
 	if (ret < 0)
 		return ret;
 
-	ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG2,
-					    TAS2764_TDM_CFG2_SCFG_MASK, iface);
+	ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG1,
+					    TAS2764_TDM_CFG1_MASK,
+					    (tdm_rx_start_slot << TAS2764_TDM_CFG1_51_SHIFT));
 	if (ret < 0)
 		return ret;
 
@@ -397,20 +394,13 @@
 	if (tx_mask == 0 || rx_mask != 0)
 		return -EINVAL;
 
-	if (slots == 1) {
-		if (tx_mask != 1)
-			return -EINVAL;
-		left_slot = 0;
-		right_slot = 0;
+	left_slot = __ffs(tx_mask);
+	tx_mask &= ~(1 << left_slot);
+	if (tx_mask == 0) {
+		right_slot = left_slot;
 	} else {
-		left_slot = __ffs(tx_mask);
-		tx_mask &= ~(1 << left_slot);
-		if (tx_mask == 0) {
-			right_slot = left_slot;
-		} else {
-			right_slot = __ffs(tx_mask);
-			tx_mask &= ~(1 << right_slot);
-		}
+		right_slot = __ffs(tx_mask);
+		tx_mask &= ~(1 << right_slot);
 	}
 
 	if (tx_mask != 0 || left_slot >= slots || right_slot >= slots)
@@ -477,7 +467,7 @@
 		.id = 0,
 		.playback = {
 			.stream_name    = "ASI1 Playback",
-			.channels_min   = 2,
+			.channels_min   = 1,
 			.channels_max   = 2,
 			.rates      = TAS2764_RATES,
 			.formats    = TAS2764_FORMATS,
@@ -501,8 +491,10 @@
 
 	tas2764->component = component;
 
-	if (tas2764->sdz_gpio)
+	if (tas2764->sdz_gpio) {
 		gpiod_set_value_cansleep(tas2764->sdz_gpio, 1);
+		usleep_range(1000, 2000);
+	}
 
 	tas2764_reset(tas2764);
 
@@ -516,22 +508,16 @@
 	if (ret < 0)
 		return ret;
 
-	ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL,
-					    TAS2764_PWR_CTRL_MASK,
-					    TAS2764_PWR_CTRL_MUTE);
-	if (ret < 0)
-		return ret;
-
 	return 0;
 }
 
 static DECLARE_TLV_DB_SCALE(tas2764_digital_tlv, 1100, 50, 0);
-static DECLARE_TLV_DB_SCALE(tas2764_playback_volume, -10000, 50, 0);
+static DECLARE_TLV_DB_SCALE(tas2764_playback_volume, -10050, 50, 1);
 
 static const struct snd_kcontrol_new tas2764_snd_controls[] = {
 	SOC_SINGLE_TLV("Speaker Volume", TAS2764_DVC, 0,
 		       TAS2764_DVC_MAX, 1, tas2764_playback_volume),
-	SOC_SINGLE_TLV("Amp Gain Volume", TAS2764_CHNL_0, 0, 0x14, 0,
+	SOC_SINGLE_TLV("Amp Gain Volume", TAS2764_CHNL_0, 1, 0x14, 0,
 		       tas2764_digital_tlv),
 };
 
@@ -539,7 +525,6 @@
 	.probe			= tas2764_codec_probe,
 	.suspend		= tas2764_codec_suspend,
 	.resume			= tas2764_codec_resume,
-	.set_bias_level		= tas2764_set_bias_level,
 	.controls		= tas2764_snd_controls,
 	.num_controls		= ARRAY_SIZE(tas2764_snd_controls),
 	.dapm_widgets		= tas2764_dapm_widgets,
@@ -556,7 +541,7 @@
 	{ TAS2764_SW_RST, 0x00 },
 	{ TAS2764_PWR_CTRL, 0x1a },
 	{ TAS2764_DVC, 0x00 },
-	{ TAS2764_CHNL_0, 0x00 },
+	{ TAS2764_CHNL_0, 0x28 },
 	{ TAS2764_TDM_CFG0, 0x09 },
 	{ TAS2764_TDM_CFG1, 0x02 },
 	{ TAS2764_TDM_CFG2, 0x0a },
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tas2764.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tas2764.h
@@ -25,7 +25,7 @@
 
 /* Power Control */
 #define TAS2764_PWR_CTRL		TAS2764_REG(0X0, 0x02)
-#define TAS2764_PWR_CTRL_MASK		GENMASK(1, 0)
+#define TAS2764_PWR_CTRL_MASK		GENMASK(2, 0)
 #define TAS2764_PWR_CTRL_ACTIVE		0x0
 #define TAS2764_PWR_CTRL_MUTE		BIT(0)
 #define TAS2764_PWR_CTRL_SHUTDOWN	BIT(1)
@@ -47,6 +47,7 @@
 #define TAS2764_TDM_CFG0_MASK		GENMASK(3, 1)
 #define TAS2764_TDM_CFG0_44_1_48KHZ	BIT(3)
 #define TAS2764_TDM_CFG0_88_2_96KHZ	(BIT(3) | BIT(1))
+#define TAS2764_TDM_CFG0_FRAME_START	BIT(0)
 
 /* TDM Configuration Reg1 */
 #define TAS2764_TDM_CFG1		TAS2764_REG(0X0, 0x09)
@@ -66,10 +67,7 @@
 #define TAS2764_TDM_CFG2_RXS_16BITS	0x0
 #define TAS2764_TDM_CFG2_RXS_24BITS	BIT(0)
 #define TAS2764_TDM_CFG2_RXS_32BITS	BIT(1)
-#define TAS2764_TDM_CFG2_SCFG_MASK	GENMASK(5, 4)
-#define TAS2764_TDM_CFG2_SCFG_I2S	0x0
-#define TAS2764_TDM_CFG2_SCFG_LEFT_J	BIT(4)
-#define TAS2764_TDM_CFG2_SCFG_RIGHT_J	BIT(5)
+#define TAS2764_TDM_CFG2_SCFG_SHIFT	4
 
 /* TDM Configuration Reg3 */
 #define TAS2764_TDM_CFG3		TAS2764_REG(0X0, 0x0c)
@@ -77,6 +75,12 @@
 #define TAS2764_TDM_CFG3_RXS_SHIFT	0x4
 #define TAS2764_TDM_CFG3_MASK		GENMASK(3, 0)
 
+/* TDM Configuration Reg4 */
+#define TAS2764_TDM_CFG4		TAS2764_REG(0X0, 0x0d)
+#define TAS2764_TDM_CFG4_TX_MASK	BIT(0)
+#define TAS2764_TDM_CFG4_TX_RISING	0x0
+#define TAS2764_TDM_CFG4_TX_FALLING	BIT(0)
+
 /* TDM Configuration Reg5 */
 #define TAS2764_TDM_CFG5		TAS2764_REG(0X0, 0x0e)
 #define TAS2764_TDM_CFG5_VSNS_MASK	BIT(6)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tas2770.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tas2770.c
@@ -38,40 +38,30 @@
 		gpiod_set_value_cansleep(tas2770->reset_gpio, 0);
 		msleep(20);
 		gpiod_set_value_cansleep(tas2770->reset_gpio, 1);
+		usleep_range(1000, 2000);
 	}
 
 	snd_soc_component_write(tas2770->component, TAS2770_SW_RST,
 		TAS2770_RST);
+	usleep_range(1000, 2000);
 }
 
-static int tas2770_set_bias_level(struct snd_soc_component *component,
-				 enum snd_soc_bias_level level)
+static int tas2770_update_pwr_ctrl(struct tas2770_priv *tas2770)
 {
-	struct tas2770_priv *tas2770 =
-			snd_soc_component_get_drvdata(component);
+	struct snd_soc_component *component = tas2770->component;
+	unsigned int val;
+	int ret;
 
-	switch (level) {
-	case SND_SOC_BIAS_ON:
-		snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-					      TAS2770_PWR_CTRL_MASK,
-					      TAS2770_PWR_CTRL_ACTIVE);
-		break;
-	case SND_SOC_BIAS_STANDBY:
-	case SND_SOC_BIAS_PREPARE:
-		snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-					      TAS2770_PWR_CTRL_MASK,
-					      TAS2770_PWR_CTRL_MUTE);
-		break;
-	case SND_SOC_BIAS_OFF:
-		snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-					      TAS2770_PWR_CTRL_MASK,
-					      TAS2770_PWR_CTRL_SHUTDOWN);
-		break;
+	if (tas2770->dac_powered)
+		val = tas2770->unmuted ?
+			TAS2770_PWR_CTRL_ACTIVE : TAS2770_PWR_CTRL_MUTE;
+	else
+		val = TAS2770_PWR_CTRL_SHUTDOWN;
 
-	default:
-		dev_err(tas2770->dev, "wrong power level setting %d\n", level);
-		return -EINVAL;
-	}
+	ret = snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
+					    TAS2770_PWR_CTRL_MASK, val);
+	if (ret < 0)
+		return ret;
 
 	return 0;
 }
@@ -110,10 +100,9 @@
 
 	if (tas2770->sdz_gpio) {
 		gpiod_set_value_cansleep(tas2770->sdz_gpio, 1);
+		usleep_range(1000, 2000);
 	} else {
-		ret = snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-						    TAS2770_PWR_CTRL_MASK,
-						    TAS2770_PWR_CTRL_ACTIVE);
+		ret = tas2770_update_pwr_ctrl(tas2770);
 		if (ret < 0)
 			return ret;
 	}
@@ -149,24 +138,19 @@
 
 	switch (event) {
 	case SND_SOC_DAPM_POST_PMU:
-		ret = snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-						    TAS2770_PWR_CTRL_MASK,
-						    TAS2770_PWR_CTRL_MUTE);
+		tas2770->dac_powered = 1;
+		ret = tas2770_update_pwr_ctrl(tas2770);
 		break;
 	case SND_SOC_DAPM_PRE_PMD:
-		ret = snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-						    TAS2770_PWR_CTRL_MASK,
-						    TAS2770_PWR_CTRL_SHUTDOWN);
+		tas2770->dac_powered = 0;
+		ret = tas2770_update_pwr_ctrl(tas2770);
 		break;
 	default:
 		dev_err(tas2770->dev, "Not supported evevt\n");
 		return -EINVAL;
 	}
 
-	if (ret < 0)
-		return ret;
-
-	return 0;
+	return ret;
 }
 
 static const struct snd_kcontrol_new isense_switch =
@@ -200,21 +184,11 @@
 static int tas2770_mute(struct snd_soc_dai *dai, int mute, int direction)
 {
 	struct snd_soc_component *component = dai->component;
-	int ret;
-
-	if (mute)
-		ret = snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-						    TAS2770_PWR_CTRL_MASK,
-						    TAS2770_PWR_CTRL_MUTE);
-	else
-		ret = snd_soc_component_update_bits(component, TAS2770_PWR_CTRL,
-						    TAS2770_PWR_CTRL_MASK,
-						    TAS2770_PWR_CTRL_ACTIVE);
-
-	if (ret < 0)
-		return ret;
+	struct tas2770_priv *tas2770 =
+			snd_soc_component_get_drvdata(component);
 
-	return 0;
+	tas2770->unmuted = !mute;
+	return tas2770_update_pwr_ctrl(tas2770);
 }
 
 static int tas2770_set_bitwidth(struct tas2770_priv *tas2770, int bitwidth)
@@ -291,11 +265,11 @@
 		ramp_rate_val = TAS2770_TDM_CFG_REG0_SMP_44_1KHZ |
 				TAS2770_TDM_CFG_REG0_31_88_2_96KHZ;
 		break;
-	case 19200:
+	case 192000:
 		ramp_rate_val = TAS2770_TDM_CFG_REG0_SMP_48KHZ |
 				TAS2770_TDM_CFG_REG0_31_176_4_192KHZ;
 		break;
-	case 17640:
+	case 176400:
 		ramp_rate_val = TAS2770_TDM_CFG_REG0_SMP_44_1KHZ |
 				TAS2770_TDM_CFG_REG0_31_176_4_192KHZ;
 		break;
@@ -334,7 +308,7 @@
 	struct snd_soc_component *component = dai->component;
 	struct tas2770_priv *tas2770 =
 			snd_soc_component_get_drvdata(component);
-	u8 tdm_rx_start_slot = 0, asi_cfg_1 = 0;
+	u8 tdm_rx_start_slot = 0, invert_fpol = 0, fpol_preinv = 0, asi_cfg_1 = 0;
 	int ret;
 
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
@@ -346,9 +320,15 @@
 	}
 
 	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_IF:
+		invert_fpol = 1;
+		fallthrough;
 	case SND_SOC_DAIFMT_NB_NF:
 		asi_cfg_1 |= TAS2770_TDM_CFG_REG1_RX_RSING;
 		break;
+	case SND_SOC_DAIFMT_IB_IF:
+		invert_fpol = 1;
+		fallthrough;
 	case SND_SOC_DAIFMT_IB_NF:
 		asi_cfg_1 |= TAS2770_TDM_CFG_REG1_RX_FALING;
 		break;
@@ -366,15 +346,19 @@
 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
 	case SND_SOC_DAIFMT_I2S:
 		tdm_rx_start_slot = 1;
+		fpol_preinv = 0;
 		break;
 	case SND_SOC_DAIFMT_DSP_A:
 		tdm_rx_start_slot = 0;
+		fpol_preinv = 1;
 		break;
 	case SND_SOC_DAIFMT_DSP_B:
 		tdm_rx_start_slot = 1;
+		fpol_preinv = 1;
 		break;
 	case SND_SOC_DAIFMT_LEFT_J:
 		tdm_rx_start_slot = 0;
+		fpol_preinv = 1;
 		break;
 	default:
 		dev_err(tas2770->dev,
@@ -388,6 +372,14 @@
 	if (ret < 0)
 		return ret;
 
+	ret = snd_soc_component_update_bits(component, TAS2770_TDM_CFG_REG0,
+					    TAS2770_TDM_CFG_REG0_FPOL_MASK,
+					    (fpol_preinv ^ invert_fpol)
+					     ? TAS2770_TDM_CFG_REG0_FPOL_RSING
+					     : TAS2770_TDM_CFG_REG0_FPOL_FALING);
+	if (ret < 0)
+		return ret;
+
 	return 0;
 }
 
@@ -403,21 +395,13 @@
 	if (tx_mask == 0 || rx_mask != 0)
 		return -EINVAL;
 
-	if (slots == 1) {
-		if (tx_mask != 1)
-			return -EINVAL;
-
-		left_slot = 0;
-		right_slot = 0;
+	left_slot = __ffs(tx_mask);
+	tx_mask &= ~(1 << left_slot);
+	if (tx_mask == 0) {
+		right_slot = left_slot;
 	} else {
-		left_slot = __ffs(tx_mask);
-		tx_mask &= ~(1 << left_slot);
-		if (tx_mask == 0) {
-			right_slot = left_slot;
-		} else {
-			right_slot = __ffs(tx_mask);
-			tx_mask &= ~(1 << right_slot);
-		}
+		right_slot = __ffs(tx_mask);
+		tx_mask &= ~(1 << right_slot);
 	}
 
 	if (tx_mask != 0 || left_slot >= slots || right_slot >= slots)
@@ -486,7 +470,7 @@
 		.id = 0,
 		.playback = {
 			.stream_name    = "ASI1 Playback",
-			.channels_min   = 2,
+			.channels_min   = 1,
 			.channels_max   = 2,
 			.rates      = TAS2770_RATES,
 			.formats    = TAS2770_FORMATS,
@@ -503,6 +487,8 @@
 	},
 };
 
+static const struct regmap_config tas2770_i2c_regmap;
+
 static int tas2770_codec_probe(struct snd_soc_component *component)
 {
 	struct tas2770_priv *tas2770 =
@@ -510,16 +496,19 @@
 
 	tas2770->component = component;
 
-	if (tas2770->sdz_gpio)
+	if (tas2770->sdz_gpio) {
 		gpiod_set_value_cansleep(tas2770->sdz_gpio, 1);
+		usleep_range(1000, 2000);
+	}
 
 	tas2770_reset(tas2770);
+	regmap_reinit_cache(tas2770->regmap, &tas2770_i2c_regmap);
 
 	return 0;
 }
 
 static DECLARE_TLV_DB_SCALE(tas2770_digital_tlv, 1100, 50, 0);
-static DECLARE_TLV_DB_SCALE(tas2770_playback_volume, -12750, 50, 0);
+static DECLARE_TLV_DB_SCALE(tas2770_playback_volume, -10050, 50, 0);
 
 static const struct snd_kcontrol_new tas2770_snd_controls[] = {
 	SOC_SINGLE_TLV("Speaker Playback Volume", TAS2770_PLAY_CFG_REG2,
@@ -532,7 +521,6 @@
 	.probe			= tas2770_codec_probe,
 	.suspend		= tas2770_codec_suspend,
 	.resume			= tas2770_codec_resume,
-	.set_bias_level = tas2770_set_bias_level,
 	.controls		= tas2770_snd_controls,
 	.num_controls		= ARRAY_SIZE(tas2770_snd_controls),
 	.dapm_widgets		= tas2770_dapm_widgets,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tas2770.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tas2770.h
@@ -41,6 +41,9 @@
 #define TAS2770_TDM_CFG_REG0_31_44_1_48KHZ  0x6
 #define TAS2770_TDM_CFG_REG0_31_88_2_96KHZ  0x8
 #define TAS2770_TDM_CFG_REG0_31_176_4_192KHZ  0xa
+#define TAS2770_TDM_CFG_REG0_FPOL_MASK  BIT(0)
+#define TAS2770_TDM_CFG_REG0_FPOL_RSING  0
+#define TAS2770_TDM_CFG_REG0_FPOL_FALING  1
     /* TDM Configuration Reg1 */
 #define TAS2770_TDM_CFG_REG1  TAS2770_REG(0X0, 0x0B)
 #define TAS2770_TDM_CFG_REG1_MASK	GENMASK(5, 1)
@@ -135,6 +138,8 @@
 	struct device *dev;
 	int v_sense_slot;
 	int i_sense_slot;
+	bool dac_powered;
+	bool unmuted;
 };
 
 #endif /* __TAS2770__ */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tda7419.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tda7419.c
@@ -624,6 +624,7 @@
 	{ .compatible = "st,tda7419" },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, tda7419_of_match);
 
 static struct i2c_driver tda7419_driver = {
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tlv320adcx140.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tlv320adcx140.c
@@ -870,7 +870,7 @@
 
 	gpio_count = device_property_count_u32(adcx140->dev,
 			"ti,gpio-config");
-	if (gpio_count == 0)
+	if (gpio_count <= 0)
 		return 0;
 
 	if (gpio_count != ADCX140_NUM_GPIO_CFGS)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tlv320aic32x4.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tlv320aic32x4.c
@@ -49,6 +49,8 @@
 	struct aic32x4_setup_data *setup;
 	struct device *dev;
 	enum aic32x4_type type;
+
+	unsigned int fmt;
 };
 
 static int aic32x4_reset_adc(struct snd_soc_dapm_widget *w,
@@ -611,6 +613,7 @@
 static int aic32x4_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
 {
 	struct snd_soc_component *component = codec_dai->component;
+	struct aic32x4_priv *aic32x4 = snd_soc_component_get_drvdata(component);
 	u8 iface_reg_1 = 0;
 	u8 iface_reg_2 = 0;
 	u8 iface_reg_3 = 0;
@@ -654,6 +657,8 @@
 		return -EINVAL;
 	}
 
+	aic32x4->fmt = fmt;
+
 	snd_soc_component_update_bits(component, AIC32X4_IFACE1,
 				AIC32X4_IFACE1_DATATYPE_MASK |
 				AIC32X4_IFACE1_MASTER_MASK, iface_reg_1);
@@ -758,6 +763,10 @@
 		return -EINVAL;
 	}
 
+	/* PCM over I2S is always 2-channel */
+	if ((aic32x4->fmt & SND_SOC_DAIFMT_FORMAT_MASK) == SND_SOC_DAIFMT_I2S)
+		channels = 2;
+
 	madc = DIV_ROUND_UP((32 * adc_resource_class), aosr);
 	max_dosr = (AIC32X4_MAX_DOSR_FREQ / sample_rate / dosr_increment) *
 			dosr_increment;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/tscs454.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/tscs454.c
@@ -3120,18 +3120,17 @@
 	unsigned int width;
 	int ret;
 
-	switch (format) {
-	case SNDRV_PCM_FORMAT_S16_LE:
+	switch (snd_pcm_format_width(format)) {
+	case 16:
 		width = FV_WL_16;
 		break;
-	case SNDRV_PCM_FORMAT_S20_3LE:
+	case 20:
 		width = FV_WL_20;
 		break;
-	case SNDRV_PCM_FORMAT_S24_3LE:
+	case 24:
 		width = FV_WL_24;
 		break;
-	case SNDRV_PCM_FORMAT_S24_LE:
-	case SNDRV_PCM_FORMAT_S32_LE:
+	case 32:
 		width = FV_WL_32;
 		break;
 	default:
@@ -3326,6 +3325,7 @@
 	.num_dapm_routes = ARRAY_SIZE(tscs454_intercon),
 	.controls =	tscs454_snd_controls,
 	.num_controls = ARRAY_SIZE(tscs454_snd_controls),
+	.endianness = 1,
 };
 
 #define TSCS454_RATES SNDRV_PCM_RATE_8000_96000
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wcd-mbhc-v2.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wcd-mbhc-v2.c
@@ -1370,7 +1370,7 @@
 		return ERR_PTR(-EINVAL);
 	}
 
-	mbhc = devm_kzalloc(dev, sizeof(*mbhc), GFP_KERNEL);
+	mbhc = kzalloc(sizeof(*mbhc), GFP_KERNEL);
 	if (!mbhc)
 		return ERR_PTR(-ENOMEM);
 
@@ -1390,61 +1390,76 @@
 
 	INIT_WORK(&mbhc->correct_plug_swch, wcd_correct_swch_plug);
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_sw_intr, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->mbhc_sw_intr, NULL,
 					wcd_mbhc_mech_plug_detect_irq,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"mbhc sw intr", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_mbhc;
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_btn_press_intr, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->mbhc_btn_press_intr, NULL,
 					wcd_mbhc_btn_press_handler,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"Button Press detect", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_sw_intr;
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_btn_release_intr, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->mbhc_btn_release_intr, NULL,
 					wcd_mbhc_btn_release_handler,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"Button Release detect", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_btn_press_intr;
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_hs_ins_intr, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->mbhc_hs_ins_intr, NULL,
 					wcd_mbhc_adc_hs_ins_irq,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"Elect Insert", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_btn_release_intr;
 
 	disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr);
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_hs_rem_intr, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->mbhc_hs_rem_intr, NULL,
 					wcd_mbhc_adc_hs_rem_irq,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"Elect Remove", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_hs_ins_intr;
 
 	disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr);
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->hph_left_ocp, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->hph_left_ocp, NULL,
 					wcd_mbhc_hphl_ocp_irq,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"HPH_L OCP detect", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_hs_rem_intr;
 
-	ret = devm_request_threaded_irq(dev, mbhc->intr_ids->hph_right_ocp, NULL,
+	ret = request_threaded_irq(mbhc->intr_ids->hph_right_ocp, NULL,
 					wcd_mbhc_hphr_ocp_irq,
 					IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 					"HPH_R OCP detect", mbhc);
 	if (ret)
-		goto err;
+		goto err_free_hph_left_ocp;
 
 	return mbhc;
-err:
+
+err_free_hph_left_ocp:
+	free_irq(mbhc->intr_ids->hph_left_ocp, mbhc);
+err_free_hs_rem_intr:
+	free_irq(mbhc->intr_ids->mbhc_hs_rem_intr, mbhc);
+err_free_hs_ins_intr:
+	free_irq(mbhc->intr_ids->mbhc_hs_ins_intr, mbhc);
+err_free_btn_release_intr:
+	free_irq(mbhc->intr_ids->mbhc_btn_release_intr, mbhc);
+err_free_btn_press_intr:
+	free_irq(mbhc->intr_ids->mbhc_btn_press_intr, mbhc);
+err_free_sw_intr:
+	free_irq(mbhc->intr_ids->mbhc_sw_intr, mbhc);
+err_free_mbhc:
+	kfree(mbhc);
+
 	dev_err(dev, "Failed to request mbhc interrupts %d\n", ret);
 
 	return ERR_PTR(ret);
@@ -1453,9 +1468,19 @@
 
 void wcd_mbhc_deinit(struct wcd_mbhc *mbhc)
 {
+	free_irq(mbhc->intr_ids->hph_right_ocp, mbhc);
+	free_irq(mbhc->intr_ids->hph_left_ocp, mbhc);
+	free_irq(mbhc->intr_ids->mbhc_hs_rem_intr, mbhc);
+	free_irq(mbhc->intr_ids->mbhc_hs_ins_intr, mbhc);
+	free_irq(mbhc->intr_ids->mbhc_btn_release_intr, mbhc);
+	free_irq(mbhc->intr_ids->mbhc_btn_press_intr, mbhc);
+	free_irq(mbhc->intr_ids->mbhc_sw_intr, mbhc);
+
 	mutex_lock(&mbhc->lock);
 	wcd_cancel_hs_detect_plug(mbhc,	&mbhc->correct_plug_swch);
 	mutex_unlock(&mbhc->lock);
+
+	kfree(mbhc);
 }
 EXPORT_SYMBOL(wcd_mbhc_deinit);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wcd9335.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wcd9335.c
@@ -1971,8 +1971,8 @@
 	case SNDRV_PCM_TRIGGER_STOP:
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
-		slim_stream_unprepare(dai_data->sruntime);
 		slim_stream_disable(dai_data->sruntime);
+		slim_stream_unprepare(dai_data->sruntime);
 		break;
 	default:
 		break;
@@ -2252,51 +2252,42 @@
 
 static const struct snd_kcontrol_new wcd9335_snd_controls[] = {
 	/* -84dB min - 40dB max */
-	SOC_SINGLE_SX_TLV("RX0 Digital Volume", WCD9335_CDC_RX0_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX1 Digital Volume", WCD9335_CDC_RX1_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX2 Digital Volume", WCD9335_CDC_RX2_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX3 Digital Volume", WCD9335_CDC_RX3_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX4 Digital Volume", WCD9335_CDC_RX4_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX5 Digital Volume", WCD9335_CDC_RX5_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX6 Digital Volume", WCD9335_CDC_RX6_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX7 Digital Volume", WCD9335_CDC_RX7_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX8 Digital Volume", WCD9335_CDC_RX8_RX_VOL_CTL,
-		0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX0 Mix Digital Volume",
-			  WCD9335_CDC_RX0_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX1 Mix Digital Volume",
-			  WCD9335_CDC_RX1_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX2 Mix Digital Volume",
-			  WCD9335_CDC_RX2_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX3 Mix Digital Volume",
-			  WCD9335_CDC_RX3_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX4 Mix Digital Volume",
-			  WCD9335_CDC_RX4_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX5 Mix Digital Volume",
-			  WCD9335_CDC_RX5_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX6 Mix Digital Volume",
-			  WCD9335_CDC_RX6_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX7 Mix Digital Volume",
-			  WCD9335_CDC_RX7_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
-	SOC_SINGLE_SX_TLV("RX8 Mix Digital Volume",
-			  WCD9335_CDC_RX8_RX_VOL_MIX_CTL,
-			  0, -84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX0 Digital Volume", WCD9335_CDC_RX0_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX1 Digital Volume", WCD9335_CDC_RX1_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX2 Digital Volume", WCD9335_CDC_RX2_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX3 Digital Volume", WCD9335_CDC_RX3_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX4 Digital Volume", WCD9335_CDC_RX4_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX5 Digital Volume", WCD9335_CDC_RX5_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX6 Digital Volume", WCD9335_CDC_RX6_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX7 Digital Volume", WCD9335_CDC_RX7_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX8 Digital Volume", WCD9335_CDC_RX8_RX_VOL_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX0 Mix Digital Volume", WCD9335_CDC_RX0_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX1 Mix Digital Volume", WCD9335_CDC_RX1_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX2 Mix Digital Volume", WCD9335_CDC_RX2_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX3 Mix Digital Volume", WCD9335_CDC_RX3_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX4 Mix Digital Volume", WCD9335_CDC_RX4_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX5 Mix Digital Volume", WCD9335_CDC_RX5_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX6 Mix Digital Volume", WCD9335_CDC_RX6_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX7 Mix Digital Volume", WCD9335_CDC_RX7_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
+	SOC_SINGLE_S8_TLV("RX8 Mix Digital Volume", WCD9335_CDC_RX8_RX_VOL_MIX_CTL,
+			-84, 40, digital_gain),
 	SOC_ENUM("RX INT0_1 HPF cut off", cf_int0_1_enum),
 	SOC_ENUM("RX INT0_2 HPF cut off", cf_int0_2_enum),
 	SOC_ENUM("RX INT1_1 HPF cut off", cf_int1_1_enum),
@@ -4859,7 +4850,7 @@
 
 	snd_soc_component_init_regmap(component, wcd->regmap);
 	/* Class-H Init*/
-	wcd->clsh_ctrl = wcd_clsh_ctrl_alloc(component, wcd->version);
+	wcd->clsh_ctrl = wcd_clsh_ctrl_alloc(component, WCD9335);
 	if (IS_ERR(wcd->clsh_ctrl))
 		return PTR_ERR(wcd->clsh_ctrl);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wcd934x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wcd934x.c
@@ -1274,29 +1274,7 @@
 	if (sido_src == wcd->sido_input_src)
 		return 0;
 
-	if (sido_src == SIDO_SOURCE_INTERNAL) {
-		regmap_update_bits(wcd->regmap, WCD934X_ANA_BUCK_CTL,
-				   WCD934X_ANA_BUCK_HI_ACCU_EN_MASK, 0);
-		usleep_range(100, 110);
-		regmap_update_bits(wcd->regmap, WCD934X_ANA_BUCK_CTL,
-				   WCD934X_ANA_BUCK_HI_ACCU_PRE_ENX_MASK, 0x0);
-		usleep_range(100, 110);
-		regmap_update_bits(wcd->regmap, WCD934X_ANA_RCO,
-				   WCD934X_ANA_RCO_BG_EN_MASK, 0);
-		usleep_range(100, 110);
-		regmap_update_bits(wcd->regmap, WCD934X_ANA_BUCK_CTL,
-				   WCD934X_ANA_BUCK_PRE_EN1_MASK,
-				   WCD934X_ANA_BUCK_PRE_EN1_ENABLE);
-		usleep_range(100, 110);
-		regmap_update_bits(wcd->regmap, WCD934X_ANA_BUCK_CTL,
-				   WCD934X_ANA_BUCK_PRE_EN2_MASK,
-				   WCD934X_ANA_BUCK_PRE_EN2_ENABLE);
-		usleep_range(100, 110);
-		regmap_update_bits(wcd->regmap, WCD934X_ANA_BUCK_CTL,
-				   WCD934X_ANA_BUCK_HI_ACCU_EN_MASK,
-				   WCD934X_ANA_BUCK_HI_ACCU_ENABLE);
-		usleep_range(100, 110);
-	} else if (sido_src == SIDO_SOURCE_RCO_BG) {
+	if (sido_src == SIDO_SOURCE_RCO_BG) {
 		regmap_update_bits(wcd->regmap, WCD934X_ANA_RCO,
 				   WCD934X_ANA_RCO_BG_EN_MASK,
 				   WCD934X_ANA_RCO_BG_ENABLE);
@@ -1382,8 +1360,6 @@
 	regmap_update_bits(wcd->regmap, WCD934X_CLK_SYS_MCLK_PRG,
 			   WCD934X_EXT_CLK_BUF_EN_MASK |
 			   WCD934X_MCLK_EN_MASK, 0x0);
-	wcd934x_set_sido_input_src(wcd, SIDO_SOURCE_INTERNAL);
-
 	regmap_update_bits(wcd->regmap, WCD934X_ANA_BIAS,
 			   WCD934X_ANA_BIAS_EN_MASK, 0);
 	regmap_update_bits(wcd->regmap, WCD934X_ANA_BIAS,
@@ -1896,9 +1872,8 @@
 	}
 
 	wcd->dai[dai->id].sconfig.rate = params_rate(params);
-	wcd934x_slim_set_hw_params(wcd, &wcd->dai[dai->id], substream->stream);
 
-	return 0;
+	return wcd934x_slim_set_hw_params(wcd, &wcd->dai[dai->id], substream->stream);
 }
 
 static int wcd934x_hw_free(struct snd_pcm_substream *substream,
@@ -1938,8 +1913,8 @@
 	case SNDRV_PCM_TRIGGER_STOP:
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
-		slim_stream_unprepare(dai_data->sruntime);
 		slim_stream_disable(dai_data->sruntime);
+		slim_stream_unprepare(dai_data->sruntime);
 		break;
 	default:
 		break;
@@ -3024,14 +2999,14 @@
 	return 0;
 }
 static const struct snd_kcontrol_new hph_type_detect_controls[] = {
-	SOC_SINGLE_EXT("HPH Type", 0, 0, UINT_MAX, 0,
+	SOC_SINGLE_EXT("HPH Type", 0, 0, WCD_MBHC_HPH_STEREO, 0,
 		       wcd934x_get_hph_type, NULL),
 };
 
 static const struct snd_kcontrol_new impedance_detect_controls[] = {
-	SOC_SINGLE_EXT("HPHL Impedance", 0, 0, UINT_MAX, 0,
+	SOC_SINGLE_EXT("HPHL Impedance", 0, 0, INT_MAX, 0,
 		       wcd934x_hph_impedance_get, NULL),
-	SOC_SINGLE_EXT("HPHR Impedance", 0, 1, UINT_MAX, 0,
+	SOC_SINGLE_EXT("HPHR Impedance", 0, 1, INT_MAX, 0,
 		       wcd934x_hph_impedance_get, NULL),
 };
 
@@ -3069,6 +3044,17 @@
 
 	return 0;
 }
+
+static void wcd934x_mbhc_deinit(struct snd_soc_component *component)
+{
+	struct wcd934x_codec *wcd = snd_soc_component_get_drvdata(component);
+
+	if (!wcd->mbhc)
+		return;
+
+	wcd_mbhc_deinit(wcd->mbhc);
+}
+
 static int wcd934x_comp_probe(struct snd_soc_component *component)
 {
 	struct wcd934x_codec *wcd = dev_get_drvdata(component->dev);
@@ -3102,6 +3088,7 @@
 {
 	struct wcd934x_codec *wcd = dev_get_drvdata(comp->dev);
 
+	wcd934x_mbhc_deinit(comp);
 	wcd_clsh_ctrl_free(wcd->clsh_ctrl);
 }
 
@@ -3257,6 +3244,9 @@
 	int value = ucontrol->value.integer.value[0];
 	int sel;
 
+	if (wcd->comp_enabled[comp] == value)
+		return 0;
+
 	wcd->comp_enabled[comp] = value;
 	sel = value ? WCD934X_HPH_GAIN_SRC_SEL_COMPANDER :
 		WCD934X_HPH_GAIN_SRC_SEL_REGISTER;
@@ -3280,10 +3270,10 @@
 	case COMPANDER_8:
 		break;
 	default:
-		break;
+		return 0;
 	}
 
-	return 0;
+	return 1;
 }
 
 static int wcd934x_rx_hph_mode_get(struct snd_kcontrol *kc,
@@ -3306,13 +3296,16 @@
 
 	mode_val = ucontrol->value.enumerated.item[0];
 
+	if (mode_val == wcd->hph_mode)
+		return 0;
+
 	if (mode_val == 0) {
 		dev_err(wcd->dev, "Invalid HPH Mode, default to ClSH HiFi\n");
 		mode_val = CLS_H_LOHIFI;
 	}
 	wcd->hph_mode = mode_val;
 
-	return 0;
+	return 1;
 }
 
 static int slim_rx_mux_get(struct snd_kcontrol *kc,
@@ -3327,6 +3320,31 @@
 	return 0;
 }
 
+static int slim_rx_mux_to_dai_id(int mux)
+{
+	int aif_id;
+
+	switch (mux) {
+	case 1:
+		aif_id = AIF1_PB;
+		break;
+	case 2:
+		aif_id = AIF2_PB;
+		break;
+	case 3:
+		aif_id = AIF3_PB;
+		break;
+	case 4:
+		aif_id = AIF4_PB;
+		break;
+	default:
+		aif_id = -1;
+		break;
+	}
+
+	return aif_id;
+}
+
 static int slim_rx_mux_put(struct snd_kcontrol *kc,
 			   struct snd_ctl_elem_value *ucontrol)
 {
@@ -3334,43 +3352,59 @@
 	struct wcd934x_codec *wcd = dev_get_drvdata(w->dapm->dev);
 	struct soc_enum *e = (struct soc_enum *)kc->private_value;
 	struct snd_soc_dapm_update *update = NULL;
+	struct wcd934x_slim_ch *ch, *c;
 	u32 port_id = w->shift;
+	bool found = false;
+	int mux_idx;
+	int prev_mux_idx = wcd->rx_port_value[port_id];
+	int aif_id;
 
-	if (wcd->rx_port_value[port_id] == ucontrol->value.enumerated.item[0])
-		return 0;
+	mux_idx = ucontrol->value.enumerated.item[0];
 
-	wcd->rx_port_value[port_id] = ucontrol->value.enumerated.item[0];
+	if (mux_idx == prev_mux_idx)
+		return 0;
 
-	switch (wcd->rx_port_value[port_id]) {
+	switch(mux_idx) {
 	case 0:
-		list_del_init(&wcd->rx_chs[port_id].list);
-		break;
-	case 1:
-		list_add_tail(&wcd->rx_chs[port_id].list,
-			      &wcd->dai[AIF1_PB].slim_ch_list);
-		break;
-	case 2:
-		list_add_tail(&wcd->rx_chs[port_id].list,
-			      &wcd->dai[AIF2_PB].slim_ch_list);
-		break;
-	case 3:
-		list_add_tail(&wcd->rx_chs[port_id].list,
-			      &wcd->dai[AIF3_PB].slim_ch_list);
+		aif_id = slim_rx_mux_to_dai_id(prev_mux_idx);
+		if (aif_id < 0)
+			return 0;
+
+		list_for_each_entry_safe(ch, c, &wcd->dai[aif_id].slim_ch_list, list) {
+			if (ch->port == port_id + WCD934X_RX_START) {
+				found = true;
+				list_del_init(&ch->list);
+				break;
+			}
+		}
+		if (!found)
+			return 0;
+
 		break;
-	case 4:
-		list_add_tail(&wcd->rx_chs[port_id].list,
-			      &wcd->dai[AIF4_PB].slim_ch_list);
+	case 1 ... 4:
+		aif_id = slim_rx_mux_to_dai_id(mux_idx);
+		if (aif_id < 0)
+			return 0;
+
+		if (list_empty(&wcd->rx_chs[port_id].list)) {
+			list_add_tail(&wcd->rx_chs[port_id].list,
+				      &wcd->dai[aif_id].slim_ch_list);
+		} else {
+			dev_err(wcd->dev ,"SLIM_RX%d PORT is busy\n", port_id);
+			return 0;
+		}
 		break;
+
 	default:
-		dev_err(wcd->dev, "Unknown AIF %d\n",
-			wcd->rx_port_value[port_id]);
+		dev_err(wcd->dev, "Unknown AIF %d\n", mux_idx);
 		goto err;
 	}
 
+	wcd->rx_port_value[port_id] = mux_idx;
 	snd_soc_dapm_mux_update_power(w->dapm, kc, wcd->rx_port_value[port_id],
 				      e, update);
 
-	return 0;
+	return 1;
 err:
 	return -EINVAL;
 }
@@ -3816,6 +3850,7 @@
 	struct soc_mixer_control *mixer =
 			(struct soc_mixer_control *)kc->private_value;
 	int enable = ucontrol->value.integer.value[0];
+	struct wcd934x_slim_ch *ch, *c;
 	int dai_id = widget->shift;
 	int port_id = mixer->shift;
 
@@ -3823,17 +3858,32 @@
 	if (enable == wcd->tx_port_value[port_id])
 		return 0;
 
-	wcd->tx_port_value[port_id] = enable;
+	if (enable) {
+		if (list_empty(&wcd->tx_chs[port_id].list)) {
+			list_add_tail(&wcd->tx_chs[port_id].list,
+				      &wcd->dai[dai_id].slim_ch_list);
+		} else {
+			dev_err(wcd->dev ,"SLIM_TX%d PORT is busy\n", port_id);
+			return 0;
+		}
+	 } else {
+		bool found = false;
 
-	if (enable)
-		list_add_tail(&wcd->tx_chs[port_id].list,
-			      &wcd->dai[dai_id].slim_ch_list);
-	else
-		list_del_init(&wcd->tx_chs[port_id].list);
+		list_for_each_entry_safe(ch, c, &wcd->dai[dai_id].slim_ch_list, list) {
+			if (ch->port == port_id) {
+				found = true;
+				list_del_init(&wcd->tx_chs[port_id].list);
+				break;
+			}
+		}
+		if (!found)
+			return 0;
+	 }
 
+	wcd->tx_port_value[port_id] = enable;
 	snd_soc_dapm_mixer_update_power(widget->dapm, kc, enable, update);
 
-	return 0;
+	return 1;
 }
 
 static const struct snd_kcontrol_new aif1_slim_cap_mixer[] = {
@@ -5826,6 +5876,7 @@
 	}
 
 	wcd->sidev = of_slim_get_device(wcd->sdev->ctrl, ifc_dev_np);
+	of_node_put(ifc_dev_np);
 	if (!wcd->sidev) {
 		dev_err(dev, "Unable to get SLIM Interface device\n");
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wcd938x-sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wcd938x-sdw.c
@@ -250,12 +250,12 @@
 					SDW_SCP_INT1_PARITY;
 	pdev->prop.lane_control_support = true;
 	if (wcd->is_tx) {
-		pdev->prop.source_ports = GENMASK(WCD938X_MAX_SWR_PORTS, 0);
+		pdev->prop.source_ports = GENMASK(WCD938X_MAX_SWR_PORTS - 1, 0);
 		pdev->prop.src_dpn_prop = wcd938x_dpn_prop;
 		wcd->ch_info = &wcd938x_sdw_tx_ch_info[0];
 		pdev->prop.wake_capable = true;
 	} else {
-		pdev->prop.sink_ports = GENMASK(WCD938X_MAX_SWR_PORTS, 0);
+		pdev->prop.sink_ports = GENMASK(WCD938X_MAX_SWR_PORTS - 1, 0);
 		pdev->prop.sink_dpn_prop = wcd938x_dpn_prop;
 		wcd->ch_info = &wcd938x_sdw_rx_ch_info[0];
 	}
@@ -266,7 +266,31 @@
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
 
-	return component_add(dev, &wcd938x_sdw_component_ops);
+	ret = component_add(dev, &wcd938x_sdw_component_ops);
+	if (ret)
+		goto err_disable_rpm;
+
+	return 0;
+
+err_disable_rpm:
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+	pm_runtime_dont_use_autosuspend(dev);
+
+	return ret;
+}
+
+static int wcd9380_remove(struct sdw_slave *pdev)
+{
+	struct device *dev = &pdev->dev;
+
+	component_del(dev, &wcd938x_sdw_component_ops);
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+	pm_runtime_dont_use_autosuspend(dev);
+
+	return 0;
 }
 
 static const struct sdw_device_id wcd9380_slave_id[] = {
@@ -307,6 +331,7 @@
 
 static struct sdw_driver wcd9380_codec_driver = {
 	.probe	= wcd9380_probe,
+	.remove	= wcd9380_remove,
 	.ops = &wcd9380_slave_ops,
 	.id_table = wcd9380_slave_id,
 	.driver = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wcd938x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wcd938x.c
@@ -1174,6 +1174,9 @@
 	case WCD938X_DIGITAL_INTR_STATUS_0:
 	case WCD938X_DIGITAL_INTR_STATUS_1:
 	case WCD938X_DIGITAL_INTR_STATUS_2:
+	case WCD938X_DIGITAL_INTR_CLEAR_0:
+	case WCD938X_DIGITAL_INTR_CLEAR_1:
+	case WCD938X_DIGITAL_INTR_CLEAR_2:
 	case WCD938X_DIGITAL_SWR_HM_TEST_0:
 	case WCD938X_DIGITAL_SWR_HM_TEST_1:
 	case WCD938X_DIGITAL_EFUSE_T_DATA_0:
@@ -1429,14 +1432,10 @@
 	return 0;
 }
 
-static int wcd938x_connect_port(struct wcd938x_sdw_priv *wcd, u8 ch_id, u8 enable)
+static int wcd938x_connect_port(struct wcd938x_sdw_priv *wcd, u8 port_num, u8 ch_id, u8 enable)
 {
-	u8 port_num;
-
-	port_num = wcd->ch_info[ch_id].port_num;
-
 	return wcd938x_sdw_connect_port(&wcd->ch_info[ch_id],
-					&wcd->port_config[port_num],
+					&wcd->port_config[port_num - 1],
 					enable);
 }
 
@@ -2505,7 +2504,7 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	int path = e->shift_l;
 
-	ucontrol->value.integer.value[0] = wcd938x->tx_mode[path];
+	ucontrol->value.enumerated.item[0] = wcd938x->tx_mode[path];
 
 	return 0;
 }
@@ -2518,6 +2517,9 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	int path = e->shift_l;
 
+	if (wcd938x->tx_mode[path] == ucontrol->value.enumerated.item[0])
+		return 0;
+
 	wcd938x->tx_mode[path] = ucontrol->value.enumerated.item[0];
 
 	return 1;
@@ -2529,7 +2531,7 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
 
-	ucontrol->value.integer.value[0] = wcd938x->hph_mode;
+	ucontrol->value.enumerated.item[0] = wcd938x->hph_mode;
 
 	return 0;
 }
@@ -2540,6 +2542,9 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
 
+	if (wcd938x->hph_mode == ucontrol->value.enumerated.item[0])
+		return 0;
+
 	wcd938x->hph_mode = ucontrol->value.enumerated.item[0];
 
 	return 1;
@@ -2560,7 +2565,7 @@
 				      WCD938X_EAR_GAIN_MASK,
 				      ucontrol->value.integer.value[0]);
 
-	return 0;
+	return 1;
 }
 
 static int wcd938x_get_compander(struct snd_kcontrol *kcontrol,
@@ -2590,6 +2595,7 @@
 	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
 	struct wcd938x_sdw_priv *wcd;
 	int value = ucontrol->value.integer.value[0];
+	int portidx;
 	struct soc_mixer_control *mc;
 	bool hphr;
 
@@ -2603,12 +2609,14 @@
 	else
 		wcd938x->comp1_enable = value;
 
+	portidx = wcd->ch_info[mc->reg].port_num;
+
 	if (value)
-		wcd938x_connect_port(wcd, mc->reg, true);
+		wcd938x_connect_port(wcd, portidx, mc->reg, true);
 	else
-		wcd938x_connect_port(wcd, mc->reg, false);
+		wcd938x_connect_port(wcd, portidx, mc->reg, false);
 
-	return 0;
+	return 1;
 }
 
 static int wcd938x_ldoh_get(struct snd_kcontrol *kcontrol,
@@ -2628,6 +2636,9 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
 
+	if (wcd938x->ldoh == ucontrol->value.integer.value[0])
+		return 0;
+
 	wcd938x->ldoh = ucontrol->value.integer.value[0];
 
 	return 1;
@@ -2650,6 +2661,9 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
 
+	if (wcd938x->bcs_dis == ucontrol->value.integer.value[0])
+		return 0;
+
 	wcd938x->bcs_dis = ucontrol->value.integer.value[0];
 
 	return 1;
@@ -2879,9 +2893,11 @@
 	struct wcd938x_sdw_priv *wcd;
 	struct soc_mixer_control *mixer = (struct soc_mixer_control *)kcontrol->private_value;
 	int dai_id = mixer->shift;
-	int portidx = mixer->reg;
+	int portidx, ch_idx = mixer->reg;
+
 
 	wcd = wcd938x->sdw_priv[dai_id];
+	portidx = wcd->ch_info[ch_idx].port_num;
 
 	ucontrol->value.integer.value[0] = wcd->port_enable[portidx];
 
@@ -2896,12 +2912,14 @@
 	struct wcd938x_sdw_priv *wcd;
 	struct soc_mixer_control *mixer =
 		(struct soc_mixer_control *)kcontrol->private_value;
-	int portidx = mixer->reg;
+	int ch_idx = mixer->reg;
+	int portidx;
 	int dai_id = mixer->shift;
 	bool enable;
 
 	wcd = wcd938x->sdw_priv[dai_id];
 
+	portidx = wcd->ch_info[ch_idx].port_num;
 	if (ucontrol->value.integer.value[0])
 		enable = true;
 	else
@@ -2909,9 +2927,9 @@
 
 	wcd->port_enable[portidx] = enable;
 
-	wcd938x_connect_port(wcd, portidx, enable);
+	wcd938x_connect_port(wcd, portidx, ch_idx, enable);
 
-	return 0;
+	return 1;
 
 }
 
@@ -3571,14 +3589,14 @@
 }
 
 static const struct snd_kcontrol_new hph_type_detect_controls[] = {
-	SOC_SINGLE_EXT("HPH Type", 0, 0, UINT_MAX, 0,
+	SOC_SINGLE_EXT("HPH Type", 0, 0, WCD_MBHC_HPH_STEREO, 0,
 		       wcd938x_get_hph_type, NULL),
 };
 
 static const struct snd_kcontrol_new impedance_detect_controls[] = {
-	SOC_SINGLE_EXT("HPHL Impedance", 0, 0, UINT_MAX, 0,
+	SOC_SINGLE_EXT("HPHL Impedance", 0, 0, INT_MAX, 0,
 		       wcd938x_hph_impedance_get, NULL),
-	SOC_SINGLE_EXT("HPHR Impedance", 0, 1, UINT_MAX, 0,
+	SOC_SINGLE_EXT("HPHR Impedance", 0, 1, INT_MAX, 0,
 		       wcd938x_hph_impedance_get, NULL),
 };
 
@@ -3603,6 +3621,8 @@
 						     WCD938X_IRQ_HPHR_OCP_INT);
 
 	wcd938x->wcd_mbhc = wcd_mbhc_init(component, &mbhc_cb, intr_ids, wcd_mbhc_fields, true);
+	if (IS_ERR(wcd938x->wcd_mbhc))
+		return PTR_ERR(wcd938x->wcd_mbhc);
 
 	snd_soc_add_component_controls(component, impedance_detect_controls,
 				       ARRAY_SIZE(impedance_detect_controls));
@@ -3611,6 +3631,14 @@
 
 	return 0;
 }
+
+static void wcd938x_mbhc_deinit(struct snd_soc_component *component)
+{
+	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
+
+	wcd_mbhc_deinit(wcd938x->wcd_mbhc);
+}
+
 /* END MBHC */
 
 static const struct snd_kcontrol_new wcd938x_snd_controls[] = {
@@ -4058,16 +4086,33 @@
 static int wcd938x_soc_codec_probe(struct snd_soc_component *component)
 {
 	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
+	struct sdw_slave *tx_sdw_dev = wcd938x->tx_sdw_dev;
 	struct device *dev = component->dev;
+	unsigned long time_left;
 	int ret, i;
 
+	time_left = wait_for_completion_timeout(&tx_sdw_dev->initialization_complete,
+						msecs_to_jiffies(2000));
+	if (!time_left) {
+		dev_err(dev, "soundwire device init timeout\n");
+		return -ETIMEDOUT;
+	}
+
 	snd_soc_component_init_regmap(component, wcd938x->regmap);
 
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret < 0)
+		return ret;
+
 	wcd938x->variant = snd_soc_component_read_field(component,
 						 WCD938X_DIGITAL_EFUSE_REG_0,
 						 WCD938X_ID_MASK);
 
 	wcd938x->clsh_info = wcd_clsh_ctrl_alloc(component, WCD938X);
+	if (IS_ERR(wcd938x->clsh_info)) {
+		pm_runtime_put(dev);
+		return PTR_ERR(wcd938x->clsh_info);
+	}
 
 	wcd938x_io_init(wcd938x);
 	/* Set all interrupts as edge triggered */
@@ -4076,6 +4121,8 @@
 			     (WCD938X_DIGITAL_INTR_LEVEL_0 + i), 0);
 	}
 
+	pm_runtime_put(dev);
+
 	wcd938x->hphr_pdm_wd_int = regmap_irq_get_virq(wcd938x->irq_chip,
 						       WCD938X_IRQ_HPHR_PDM_WD_INT);
 	wcd938x->hphl_pdm_wd_int = regmap_irq_get_virq(wcd938x->irq_chip,
@@ -4087,20 +4134,26 @@
 	ret = request_threaded_irq(wcd938x->hphr_pdm_wd_int, NULL, wcd938x_wd_handle_irq,
 				   IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 				   "HPHR PDM WD INT", wcd938x);
-	if (ret)
+	if (ret) {
 		dev_err(dev, "Failed to request HPHR WD interrupt (%d)\n", ret);
+		goto err_free_clsh_ctrl;
+	}
 
 	ret = request_threaded_irq(wcd938x->hphl_pdm_wd_int, NULL, wcd938x_wd_handle_irq,
 				   IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 				   "HPHL PDM WD INT", wcd938x);
-	if (ret)
+	if (ret) {
 		dev_err(dev, "Failed to request HPHL WD interrupt (%d)\n", ret);
+		goto err_free_hphr_pdm_wd_int;
+	}
 
 	ret = request_threaded_irq(wcd938x->aux_pdm_wd_int, NULL, wcd938x_wd_handle_irq,
 				   IRQF_ONESHOT | IRQF_TRIGGER_RISING,
 				   "AUX PDM WD INT", wcd938x);
-	if (ret)
+	if (ret) {
 		dev_err(dev, "Failed to request Aux WD interrupt (%d)\n", ret);
+		goto err_free_hphl_pdm_wd_int;
+	}
 
 	/* Disable watchdog interrupt for HPH and AUX */
 	disable_irq_nosync(wcd938x->hphr_pdm_wd_int);
@@ -4115,7 +4168,7 @@
 			dev_err(component->dev,
 				"%s: Failed to add snd ctrls for variant: %d\n",
 				__func__, wcd938x->variant);
-			goto err;
+			goto err_free_aux_pdm_wd_int;
 		}
 		break;
 	case WCD9385:
@@ -4125,7 +4178,7 @@
 			dev_err(component->dev,
 				"%s: Failed to add snd ctrls for variant: %d\n",
 				__func__, wcd938x->variant);
-			goto err;
+			goto err_free_aux_pdm_wd_int;
 		}
 		break;
 	default:
@@ -4133,12 +4186,38 @@
 	}
 
 	ret = wcd938x_mbhc_init(component);
-	if (ret)
+	if (ret) {
 		dev_err(component->dev,  "mbhc initialization failed\n");
-err:
+		goto err_free_aux_pdm_wd_int;
+	}
+
+	return 0;
+
+err_free_aux_pdm_wd_int:
+	free_irq(wcd938x->aux_pdm_wd_int, wcd938x);
+err_free_hphl_pdm_wd_int:
+	free_irq(wcd938x->hphl_pdm_wd_int, wcd938x);
+err_free_hphr_pdm_wd_int:
+	free_irq(wcd938x->hphr_pdm_wd_int, wcd938x);
+err_free_clsh_ctrl:
+	wcd_clsh_ctrl_free(wcd938x->clsh_info);
+
 	return ret;
 }
 
+static void wcd938x_soc_codec_remove(struct snd_soc_component *component)
+{
+	struct wcd938x_priv *wcd938x = snd_soc_component_get_drvdata(component);
+
+	wcd938x_mbhc_deinit(component);
+
+	free_irq(wcd938x->aux_pdm_wd_int, wcd938x);
+	free_irq(wcd938x->hphl_pdm_wd_int, wcd938x);
+	free_irq(wcd938x->hphr_pdm_wd_int, wcd938x);
+
+	wcd_clsh_ctrl_free(wcd938x->clsh_info);
+}
+
 static int wcd938x_codec_set_jack(struct snd_soc_component *comp,
 				  struct snd_soc_jack *jack, void *data)
 {
@@ -4155,6 +4234,7 @@
 static const struct snd_soc_component_driver soc_codec_dev_wcd938x = {
 	.name = "wcd938x_codec",
 	.probe = wcd938x_soc_codec_probe,
+	.remove = wcd938x_soc_codec_remove,
 	.controls = wcd938x_snd_controls,
 	.num_controls = ARRAY_SIZE(wcd938x_snd_controls),
 	.dapm_widgets = wcd938x_dapm_widgets,
@@ -4284,7 +4364,7 @@
 static const struct snd_soc_dai_ops wcd938x_sdw_dai_ops = {
 	.hw_params = wcd938x_codec_hw_params,
 	.hw_free = wcd938x_codec_free,
-	.set_sdw_stream = wcd938x_codec_set_sdw_stream,
+	.set_stream = wcd938x_codec_set_sdw_stream,
 };
 
 static struct snd_soc_dai_driver wcd938x_dais[] = {
@@ -4331,7 +4411,8 @@
 	wcd938x->rxdev = wcd938x_sdw_device_get(wcd938x->rxnode);
 	if (!wcd938x->rxdev) {
 		dev_err(dev, "could not find slave with matching of node\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_unbind;
 	}
 	wcd938x->sdw_priv[AIF1_PB] = dev_get_drvdata(wcd938x->rxdev);
 	wcd938x->sdw_priv[AIF1_PB]->wcd938x = wcd938x;
@@ -4339,46 +4420,47 @@
 	wcd938x->txdev = wcd938x_sdw_device_get(wcd938x->txnode);
 	if (!wcd938x->txdev) {
 		dev_err(dev, "could not find txslave with matching of node\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_put_rxdev;
 	}
 	wcd938x->sdw_priv[AIF1_CAP] = dev_get_drvdata(wcd938x->txdev);
 	wcd938x->sdw_priv[AIF1_CAP]->wcd938x = wcd938x;
 	wcd938x->tx_sdw_dev = dev_to_sdw_dev(wcd938x->txdev);
-	if (!wcd938x->tx_sdw_dev) {
-		dev_err(dev, "could not get txslave with matching of dev\n");
-		return -EINVAL;
-	}
 
 	/* As TX is main CSR reg interface, which should not be suspended first.
 	 * expicilty add the dependency link */
 	if (!device_link_add(wcd938x->rxdev, wcd938x->txdev, DL_FLAG_STATELESS |
 			    DL_FLAG_PM_RUNTIME)) {
 		dev_err(dev, "could not devlink tx and rx\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_put_txdev;
 	}
 
 	if (!device_link_add(dev, wcd938x->txdev, DL_FLAG_STATELESS |
 					DL_FLAG_PM_RUNTIME)) {
 		dev_err(dev, "could not devlink wcd and tx\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_remove_rxtx_link;
 	}
 
 	if (!device_link_add(dev, wcd938x->rxdev, DL_FLAG_STATELESS |
 					DL_FLAG_PM_RUNTIME)) {
 		dev_err(dev, "could not devlink wcd and rx\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err_remove_tx_link;
 	}
 
 	wcd938x->regmap = devm_regmap_init_sdw(wcd938x->tx_sdw_dev, &wcd938x_regmap_config);
 	if (IS_ERR(wcd938x->regmap)) {
 		dev_err(dev, "%s: tx csr regmap not found\n", __func__);
-		return PTR_ERR(wcd938x->regmap);
+		ret = PTR_ERR(wcd938x->regmap);
+		goto err_remove_rx_link;
 	}
 
 	ret = wcd938x_irq_init(wcd938x, dev);
 	if (ret) {
 		dev_err(dev, "%s: IRQ init failed: %d\n", __func__, ret);
-		return ret;
+		goto err_remove_rx_link;
 	}
 
 	wcd938x->sdw_priv[AIF1_PB]->slave_irq = wcd938x->virq;
@@ -4387,27 +4469,45 @@
 	ret = wcd938x_set_micbias_data(wcd938x);
 	if (ret < 0) {
 		dev_err(dev, "%s: bad micbias pdata\n", __func__);
-		return ret;
+		goto err_remove_rx_link;
 	}
 
 	ret = snd_soc_register_component(dev, &soc_codec_dev_wcd938x,
 					 wcd938x_dais, ARRAY_SIZE(wcd938x_dais));
-	if (ret)
+	if (ret) {
 		dev_err(dev, "%s: Codec registration failed\n",
 				__func__);
+		goto err_remove_rx_link;
+	}
 
-	return ret;
+	return 0;
 
+err_remove_rx_link:
+	device_link_remove(dev, wcd938x->rxdev);
+err_remove_tx_link:
+	device_link_remove(dev, wcd938x->txdev);
+err_remove_rxtx_link:
+	device_link_remove(wcd938x->rxdev, wcd938x->txdev);
+err_put_txdev:
+	put_device(wcd938x->txdev);
+err_put_rxdev:
+	put_device(wcd938x->rxdev);
+err_unbind:
+	component_unbind_all(dev, wcd938x);
+
+	return ret;
 }
 
 static void wcd938x_unbind(struct device *dev)
 {
 	struct wcd938x_priv *wcd938x = dev_get_drvdata(dev);
 
+	snd_soc_unregister_component(dev);
 	device_link_remove(dev, wcd938x->txdev);
 	device_link_remove(dev, wcd938x->rxdev);
 	device_link_remove(wcd938x->rxdev, wcd938x->txdev);
-	snd_soc_unregister_component(dev);
+	put_device(wcd938x->txdev);
+	put_device(wcd938x->rxdev);
 	component_unbind_all(dev, wcd938x);
 }
 
@@ -4473,7 +4573,7 @@
 	ret = wcd938x_populate_dt_data(wcd938x, dev);
 	if (ret) {
 		dev_err(dev, "%s: Fail to obtain platform data\n", __func__);
-		return -EINVAL;
+		return ret;
 	}
 
 	ret = wcd938x_add_slave_components(wcd938x, dev, &match);
@@ -4498,7 +4598,13 @@
 
 static int wcd938x_remove(struct platform_device *pdev)
 {
-	component_master_del(&pdev->dev, &wcd938x_comp_ops);
+	struct device *dev = &pdev->dev;
+
+	component_master_del(dev, &wcd938x_comp_ops);
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+	pm_runtime_dont_use_autosuspend(dev);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm0010.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm0010.c
@@ -952,7 +952,7 @@
 	if (ret) {
 		dev_err(wm0010->dev, "Failed to set IRQ %d as wake source: %d\n",
 			irq, ret);
-		return ret;
+		goto free_irq;
 	}
 
 	if (spi->max_speed_hz)
@@ -964,9 +964,18 @@
 				     &soc_component_dev_wm0010, wm0010_dai,
 				     ARRAY_SIZE(wm0010_dai));
 	if (ret < 0)
-		return ret;
+		goto disable_irq_wake;
 
 	return 0;
+
+disable_irq_wake:
+	irq_set_irq_wake(wm0010->irq, 0);
+
+free_irq:
+	if (wm0010->irq)
+		free_irq(wm0010->irq, wm0010);
+
+	return ret;
 }
 
 static int wm0010_spi_remove(struct spi_device *spi)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm2000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm2000.c
@@ -536,7 +536,7 @@
 {
 	struct i2c_client *i2c = wm2000->i2c;
 	int i, j;
-	int ret;
+	int ret = 0;
 
 	if (wm2000->anc_mode == mode)
 		return 0;
@@ -566,13 +566,13 @@
 		ret = anc_transitions[i].step[j](i2c,
 						 anc_transitions[i].analogue);
 		if (ret != 0)
-			return ret;
+			break;
 	}
 
 	if (anc_transitions[i].dest == ANC_OFF)
 		clk_disable_unprepare(wm2000->mclk);
 
-	return 0;
+	return ret;
 }
 
 static int wm2000_anc_set_mode(struct wm2000_priv *wm2000)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm5110.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm5110.c
@@ -302,7 +302,7 @@
 		} else {
 			wseq = wm5110_no_dre_left_enable;
 			nregs = ARRAY_SIZE(wm5110_no_dre_left_enable);
-			priv->out_up_delay += 10;
+			priv->out_up_delay += 10000;
 		}
 		break;
 	case ARIZONA_OUT1R_ENA_SHIFT:
@@ -312,7 +312,7 @@
 		} else {
 			wseq = wm5110_no_dre_right_enable;
 			nregs = ARRAY_SIZE(wm5110_no_dre_right_enable);
-			priv->out_up_delay += 10;
+			priv->out_up_delay += 10000;
 		}
 		break;
 	default:
@@ -338,7 +338,7 @@
 			snd_soc_component_update_bits(component,
 						      ARIZONA_SPARE_TRIGGERS,
 						      ARIZONA_WS_TRG1, 0);
-			priv->out_down_delay += 27;
+			priv->out_down_delay += 27000;
 		}
 		break;
 	case ARIZONA_OUT1R_ENA_SHIFT:
@@ -350,7 +350,7 @@
 			snd_soc_component_update_bits(component,
 						      ARIZONA_SPARE_TRIGGERS,
 						      ARIZONA_WS_TRG2, 0);
-			priv->out_down_delay += 27;
+			priv->out_down_delay += 27000;
 		}
 		break;
 	default:
@@ -413,6 +413,7 @@
 	unsigned int rnew = (!!ucontrol->value.integer.value[1]) << mc->rshift;
 	unsigned int lold, rold;
 	unsigned int lena, rena;
+	bool change = false;
 	int ret;
 
 	snd_soc_dapm_mutex_lock(dapm);
@@ -440,8 +441,8 @@
 		goto err;
 	}
 
-	ret = regmap_update_bits(arizona->regmap, ARIZONA_DRE_ENABLE,
-				 mask, lnew | rnew);
+	ret = regmap_update_bits_check(arizona->regmap, ARIZONA_DRE_ENABLE,
+				       mask, lnew | rnew, &change);
 	if (ret) {
 		dev_err(arizona->dev, "Failed to set DRE: %d\n", ret);
 		goto err;
@@ -454,6 +455,9 @@
 	if (!rnew && rold)
 		wm5110_clear_pga_volume(arizona, mc->rshift);
 
+	if (change)
+		ret = 1;
+
 err:
 	snd_soc_dapm_mutex_unlock(dapm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8350.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8350.c
@@ -1537,18 +1537,38 @@
 	wm8350_clear_bits(wm8350, WM8350_JACK_DETECT,
 			  WM8350_JDL_ENA | WM8350_JDR_ENA);
 
-	wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_JCK_DET_L,
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_JCK_DET_L,
 			    wm8350_hpl_jack_handler, 0, "Left jack detect",
 			    priv);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_JCK_DET_R,
+	if (ret != 0)
+		goto err;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_JCK_DET_R,
 			    wm8350_hpr_jack_handler, 0, "Right jack detect",
 			    priv);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_MICSCD,
+	if (ret != 0)
+		goto free_jck_det_l;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_MICSCD,
 			    wm8350_mic_handler, 0, "Microphone short", priv);
-	wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_MICD,
+	if (ret != 0)
+		goto free_jck_det_r;
+
+	ret = wm8350_register_irq(wm8350, WM8350_IRQ_CODEC_MICD,
 			    wm8350_mic_handler, 0, "Microphone detect", priv);
+	if (ret != 0)
+		goto free_micscd;
 
 	return 0;
+
+free_micscd:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CODEC_MICSCD, priv);
+free_jck_det_r:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CODEC_JCK_DET_R, priv);
+free_jck_det_l:
+	wm8350_free_irq(wm8350, WM8350_IRQ_CODEC_JCK_DET_L, priv);
+err:
+	return ret;
 }
 
 static void wm8350_component_remove(struct snd_soc_component *component)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8731.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8731.c
@@ -602,7 +602,7 @@
 	ret = wm8731_reset(wm8731->regmap);
 	if (ret < 0) {
 		dev_err(dev, "Failed to issue reset: %d\n", ret);
-		goto err_regulator_enable;
+		goto err;
 	}
 
 	/* Clear POWEROFF, keep everything else disabled */
@@ -619,10 +619,7 @@
 
 	regcache_mark_dirty(wm8731->regmap);
 
-err_regulator_enable:
-	/* Regulators will be enabled by bias management */
-	regulator_bulk_disable(ARRAY_SIZE(wm8731->supplies), wm8731->supplies);
-
+err:
 	return ret;
 }
 
@@ -766,21 +763,27 @@
 		ret = PTR_ERR(wm8731->regmap);
 		dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
 			ret);
-		return ret;
+		goto err_regulator_enable;
 	}
 
 	ret = wm8731_hw_init(&i2c->dev, wm8731);
 	if (ret != 0)
-		return ret;
+		goto err_regulator_enable;
 
 	ret = devm_snd_soc_register_component(&i2c->dev,
 			&soc_component_dev_wm8731, &wm8731_dai, 1);
 	if (ret != 0) {
 		dev_err(&i2c->dev, "Failed to register CODEC: %d\n", ret);
-		return ret;
+		goto err_regulator_enable;
 	}
 
 	return 0;
+
+err_regulator_enable:
+	/* Regulators will be enabled by bias management */
+	regulator_bulk_disable(ARRAY_SIZE(wm8731->supplies), wm8731->supplies);
+
+	return ret;
 }
 
 static int wm8731_i2c_remove(struct i2c_client *client)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8904.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8904.c
@@ -697,6 +697,7 @@
 	int dcs_mask;
 	int dcs_l, dcs_r;
 	int dcs_l_reg, dcs_r_reg;
+	int an_out_reg;
 	int timeout;
 	int pwr_reg;
 
@@ -712,6 +713,7 @@
 		dcs_mask = WM8904_DCS_ENA_CHAN_0 | WM8904_DCS_ENA_CHAN_1;
 		dcs_r_reg = WM8904_DC_SERVO_8;
 		dcs_l_reg = WM8904_DC_SERVO_9;
+		an_out_reg = WM8904_ANALOGUE_OUT1_LEFT;
 		dcs_l = 0;
 		dcs_r = 1;
 		break;
@@ -720,6 +722,7 @@
 		dcs_mask = WM8904_DCS_ENA_CHAN_2 | WM8904_DCS_ENA_CHAN_3;
 		dcs_r_reg = WM8904_DC_SERVO_6;
 		dcs_l_reg = WM8904_DC_SERVO_7;
+		an_out_reg = WM8904_ANALOGUE_OUT2_LEFT;
 		dcs_l = 2;
 		dcs_r = 3;
 		break;
@@ -792,6 +795,10 @@
 		snd_soc_component_update_bits(component, reg,
 				    WM8904_HPL_ENA_OUTP | WM8904_HPR_ENA_OUTP,
 				    WM8904_HPL_ENA_OUTP | WM8904_HPR_ENA_OUTP);
+
+		/* Update volume, requires PGA to be powered */
+		val = snd_soc_component_read(component, an_out_reg);
+		snd_soc_component_write(component, an_out_reg, val);
 		break;
 
 	case SND_SOC_DAPM_POST_PMU:
@@ -2299,6 +2306,9 @@
 	regmap_update_bits(wm8904->regmap, WM8904_BIAS_CONTROL_0,
 			    WM8904_POBCTRL, 0);
 
+	/* Fill the cache for the ADC test register */
+	regmap_read(wm8904->regmap, WM8904_ADC_TEST_0, &val);
+
 	/* Can leave the device powered off until we need it */
 	regcache_cache_only(wm8904->regmap, true);
 	regulator_bulk_disable(ARRAY_SIZE(wm8904->supplies), wm8904->supplies);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8958-dsp2.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8958-dsp2.c
@@ -530,7 +530,7 @@
 
 	wm8958_dsp_apply(component, mbc, wm8994->mbc_ena[mbc]);
 
-	return 0;
+	return 1;
 }
 
 #define WM8958_MBC_SWITCH(xname, xval) {\
@@ -656,7 +656,7 @@
 
 	wm8958_dsp_apply(component, vss, wm8994->vss_ena[vss]);
 
-	return 0;
+	return 1;
 }
 
 
@@ -730,7 +730,7 @@
 
 	wm8958_dsp_apply(component, hpf % 3, ucontrol->value.integer.value[0]);
 
-	return 0;
+	return 1;
 }
 
 #define WM8958_HPF_SWITCH(xname, xval) {\
@@ -824,7 +824,7 @@
 
 	wm8958_dsp_apply(component, eq, ucontrol->value.integer.value[0]);
 
-	return 0;
+	return 1;
 }
 
 #define WM8958_ENH_EQ_SWITCH(xname, xval) {\
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8962.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8962.c
@@ -1840,6 +1840,49 @@
 	       4, 1, 0, inmix_tlv),
 };
 
+static int tp_event(struct snd_soc_dapm_widget *w,
+		    struct snd_kcontrol *kcontrol, int event)
+{
+	int ret, reg, val, mask;
+	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+
+	ret = pm_runtime_resume_and_get(component->dev);
+	if (ret < 0) {
+		dev_err(component->dev, "Failed to resume device: %d\n", ret);
+		return ret;
+	}
+
+	reg = WM8962_ADDITIONAL_CONTROL_4;
+
+	if (!strcmp(w->name, "TEMP_HP")) {
+		mask = WM8962_TEMP_ENA_HP_MASK;
+		val = WM8962_TEMP_ENA_HP;
+	} else if (!strcmp(w->name, "TEMP_SPK")) {
+		mask = WM8962_TEMP_ENA_SPK_MASK;
+		val = WM8962_TEMP_ENA_SPK;
+	} else {
+		pm_runtime_put(component->dev);
+		return -EINVAL;
+	}
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMD:
+		val = 0;
+		fallthrough;
+	case SND_SOC_DAPM_POST_PMU:
+		ret = snd_soc_component_update_bits(component, reg, mask, val);
+		break;
+	default:
+		WARN(1, "Invalid event %d\n", event);
+		pm_runtime_put(component->dev);
+		return -EINVAL;
+	}
+
+	pm_runtime_put(component->dev);
+
+	return 0;
+}
+
 static int cp_event(struct snd_soc_dapm_widget *w,
 		    struct snd_kcontrol *kcontrol, int event)
 {
@@ -2133,8 +2176,10 @@
 SND_SOC_DAPM_SUPPLY_S("DSP2", 1, WM8962_DSP2_POWER_MANAGEMENT,
 		      WM8962_DSP2_ENA_SHIFT, 0, dsp2_event,
 		      SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
-SND_SOC_DAPM_SUPPLY("TEMP_HP", WM8962_ADDITIONAL_CONTROL_4, 2, 0, NULL, 0),
-SND_SOC_DAPM_SUPPLY("TEMP_SPK", WM8962_ADDITIONAL_CONTROL_4, 1, 0, NULL, 0),
+SND_SOC_DAPM_SUPPLY("TEMP_HP", SND_SOC_NOPM, 0, 0, tp_event,
+		SND_SOC_DAPM_POST_PMU|SND_SOC_DAPM_POST_PMD),
+SND_SOC_DAPM_SUPPLY("TEMP_SPK", SND_SOC_NOPM, 0, 0, tp_event,
+		SND_SOC_DAPM_POST_PMU|SND_SOC_DAPM_POST_PMD),
 
 SND_SOC_DAPM_MIXER("INPGAL", WM8962_LEFT_INPUT_PGA_CONTROL, 4, 0,
 		   inpgal, ARRAY_SIZE(inpgal)),
@@ -2174,6 +2219,9 @@
 
 SND_SOC_DAPM_OUTPUT("HPOUTL"),
 SND_SOC_DAPM_OUTPUT("HPOUTR"),
+
+SND_SOC_DAPM_PGA("SPKOUTL Output", WM8962_CLASS_D_CONTROL_1, 6, 0, NULL, 0),
+SND_SOC_DAPM_PGA("SPKOUTR Output", WM8962_CLASS_D_CONTROL_1, 7, 0, NULL, 0),
 };
 
 static const struct snd_soc_dapm_widget wm8962_dapm_spk_mono_widgets[] = {
@@ -2181,7 +2229,6 @@
 		   spkmixl, ARRAY_SIZE(spkmixl)),
 SND_SOC_DAPM_MUX_E("Speaker PGA", WM8962_PWR_MGMT_2, 4, 0, &spkoutl_mux,
 		   out_pga_event, SND_SOC_DAPM_POST_PMU),
-SND_SOC_DAPM_PGA("Speaker Output", WM8962_CLASS_D_CONTROL_1, 7, 0, NULL, 0),
 SND_SOC_DAPM_OUTPUT("SPKOUT"),
 };
 
@@ -2196,9 +2243,6 @@
 SND_SOC_DAPM_MUX_E("SPKOUTR PGA", WM8962_PWR_MGMT_2, 3, 0, &spkoutr_mux,
 		   out_pga_event, SND_SOC_DAPM_POST_PMU),
 
-SND_SOC_DAPM_PGA("SPKOUTR Output", WM8962_CLASS_D_CONTROL_1, 7, 0, NULL, 0),
-SND_SOC_DAPM_PGA("SPKOUTL Output", WM8962_CLASS_D_CONTROL_1, 6, 0, NULL, 0),
-
 SND_SOC_DAPM_OUTPUT("SPKOUTL"),
 SND_SOC_DAPM_OUTPUT("SPKOUTR"),
 };
@@ -2308,12 +2352,18 @@
 	{ "Speaker PGA", "Mixer", "Speaker Mixer" },
 	{ "Speaker PGA", "DAC", "DACL" },
 
-	{ "Speaker Output", NULL, "Speaker PGA" },
-	{ "Speaker Output", NULL, "SYSCLK" },
-	{ "Speaker Output", NULL, "TOCLK" },
-	{ "Speaker Output", NULL, "TEMP_SPK" },
+	{ "SPKOUTL Output", NULL, "Speaker PGA" },
+	{ "SPKOUTL Output", NULL, "SYSCLK" },
+	{ "SPKOUTL Output", NULL, "TOCLK" },
+	{ "SPKOUTL Output", NULL, "TEMP_SPK" },
 
-	{ "SPKOUT", NULL, "Speaker Output" },
+	{ "SPKOUTR Output", NULL, "Speaker PGA" },
+	{ "SPKOUTR Output", NULL, "SYSCLK" },
+	{ "SPKOUTR Output", NULL, "TOCLK" },
+	{ "SPKOUTR Output", NULL, "TEMP_SPK" },
+
+	{ "SPKOUT", NULL, "SPKOUTL Output" },
+	{ "SPKOUT", NULL, "SPKOUTR Output" },
 };
 
 static const struct snd_soc_dapm_route wm8962_spk_stereo_intercon[] = {
@@ -2445,6 +2495,14 @@
 		snd_soc_component_update_bits(component, WM8962_CLOCKING2,
 				WM8962_SYSCLK_ENA_MASK, WM8962_SYSCLK_ENA);
 
+	/* DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
+	 * correct frequency of LRCLK and BCLK. Sometimes the read-only value
+	 * can't be updated timely after enabling SYSCLK. This results in wrong
+	 * calculation values. Delay is introduced here to wait for newest
+	 * value from register. The time of the delay should be at least
+	 * 500~1000us according to test.
+	 */
+	usleep_range(500, 1000);
 	dspclk = snd_soc_component_read(component, WM8962_CLOCKING1);
 
 	if (snd_soc_component_get_bias_level(component) != SND_SOC_BIAS_ON)
@@ -2848,8 +2906,12 @@
 	switch (fll_id) {
 	case WM8962_FLL_MCLK:
 	case WM8962_FLL_BCLK:
+		fll1 |= (fll_id - 1) << WM8962_FLL_REFCLK_SRC_SHIFT;
+		break;
 	case WM8962_FLL_OSC:
 		fll1 |= (fll_id - 1) << WM8962_FLL_REFCLK_SRC_SHIFT;
+		snd_soc_component_update_bits(component, WM8962_PLL2,
+					      WM8962_OSC_ENA, WM8962_OSC_ENA);
 		break;
 	case WM8962_FLL_INT:
 		snd_soc_component_update_bits(component, WM8962_FLL_CONTROL_1,
@@ -2858,7 +2920,7 @@
 				    WM8962_FLL_FRC_NCO, WM8962_FLL_FRC_NCO);
 		break;
 	default:
-		dev_err(component->dev, "Unknown FLL source %d\n", ret);
+		dev_err(component->dev, "Unknown FLL source %d\n", source);
 		return -EINVAL;
 	}
 
@@ -3763,6 +3825,11 @@
 	if (ret < 0)
 		goto err_pm_runtime;
 
+	regmap_update_bits(wm8962->regmap, WM8962_ADDITIONAL_CONTROL_4,
+			    WM8962_TEMP_ENA_HP_MASK, 0);
+	regmap_update_bits(wm8962->regmap, WM8962_ADDITIONAL_CONTROL_4,
+			    WM8962_TEMP_ENA_SPK_MASK, 0);
+
 	regcache_cache_only(wm8962->regmap, true);
 
 	/* The drivers should power up as needed */
@@ -3867,6 +3934,7 @@
 #endif
 
 static const struct dev_pm_ops wm8962_pm = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume)
 	SET_RUNTIME_PM_OPS(wm8962_runtime_suspend, wm8962_runtime_resume, NULL)
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8974.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8974.c
@@ -186,7 +186,7 @@
 
 /* Boost mixer */
 static const struct snd_kcontrol_new wm8974_boost_mixer[] = {
-SOC_DAPM_SINGLE("Aux Switch", WM8974_INPPGA, 6, 1, 1),
+SOC_DAPM_SINGLE("PGA Switch", WM8974_INPPGA, 6, 1, 1),
 };
 
 /* Input PGA */
@@ -246,8 +246,8 @@
 
 	/* Boost Mixer */
 	{"ADC", NULL, "Boost Mixer"},
-	{"Boost Mixer", "Aux Switch", "Aux Input"},
-	{"Boost Mixer", NULL, "Input PGA"},
+	{"Boost Mixer", NULL, "Aux Input"},
+	{"Boost Mixer", "PGA Switch", "Input PGA"},
 	{"Boost Mixer", NULL, "MICP"},
 
 	/* Input PGA */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm8994.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm8994.c
@@ -3853,7 +3853,12 @@
 	} else {
 		dev_dbg(component->dev, "Jack not detected\n");
 
+		/* Release wm8994->accdet_lock to avoid deadlock:
+		 * cancel_delayed_work_sync() takes wm8994->mic_work internal
+		 * lock and wm1811_mic_work takes wm8994->accdet_lock */
+		mutex_unlock(&wm8994->accdet_lock);
 		cancel_delayed_work_sync(&wm8994->mic_work);
+		mutex_lock(&wm8994->accdet_lock);
 
 		snd_soc_component_update_bits(component, WM8958_MICBIAS2,
 				    WM8958_MICB2_DISCH, WM8958_MICB2_DISCH);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wm_adsp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wm_adsp.c
@@ -794,7 +794,7 @@
 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	struct wm_adsp *dsp = snd_soc_component_get_drvdata(component);
-	int ret = 0;
+	int ret = 1;
 
 	if (ucontrol->value.enumerated.item[0] == dsp[e->shift_l].fw)
 		return 0;
@@ -3766,12 +3766,12 @@
 		ret = wm_adsp_buffer_read(buf, caps->region_defs[i].base_offset,
 					  &region->base_addr);
 		if (ret < 0)
-			return ret;
+			goto err;
 
 		ret = wm_adsp_buffer_read(buf, caps->region_defs[i].size_offset,
 					  &offset);
 		if (ret < 0)
-			return ret;
+			goto err;
 
 		region->cumulative_size = offset;
 
@@ -3782,6 +3782,10 @@
 	}
 
 	return 0;
+
+err:
+	kfree(buf->regions);
+	return ret;
 }
 
 static void wm_adsp_buffer_clear(struct wm_adsp_compr_buf *buf)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/codecs/wsa881x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/codecs/wsa881x.c
@@ -646,7 +646,6 @@
 	.readable_reg = wsa881x_readable_register,
 	.reg_format_endian = REGMAP_ENDIAN_NATIVE,
 	.val_format_endian = REGMAP_ENDIAN_NATIVE,
-	.can_multi_write = true,
 };
 
 enum {
@@ -772,7 +771,8 @@
 
 		usleep_range(1000, 1010);
 	}
-	return 0;
+
+	return 1;
 }
 
 static int wsa881x_get_port(struct snd_kcontrol *kcontrol,
@@ -816,15 +816,22 @@
 		(struct soc_mixer_control *)kcontrol->private_value;
 	int portidx = mixer->reg;
 
-	if (ucontrol->value.integer.value[0])
+	if (ucontrol->value.integer.value[0]) {
+		if (data->port_enable[portidx])
+			return 0;
+
 		data->port_enable[portidx] = true;
-	else
+	} else {
+		if (!data->port_enable[portidx])
+			return 0;
+
 		data->port_enable[portidx] = false;
+	}
 
 	if (portidx == WSA881X_PORT_BOOST) /* Boost Switch */
 		wsa881x_boost_ctrl(comp, data->port_enable[portidx]);
 
-	return 0;
+	return 1;
 }
 
 static const char * const smart_boost_lvl_text[] = {
@@ -1018,7 +1025,7 @@
 	.hw_params = wsa881x_hw_params,
 	.hw_free = wsa881x_hw_free,
 	.mute_stream = wsa881x_digital_mute,
-	.set_sdw_stream = wsa881x_set_sdw_stream,
+	.set_stream = wsa881x_set_sdw_stream,
 };
 
 static struct snd_soc_dai_driver wsa881x_dais[] = {
@@ -1113,7 +1120,7 @@
 	wsa881x->sconfig.frame_rate = 48000;
 	wsa881x->sconfig.direction = SDW_DATA_DIR_RX;
 	wsa881x->sconfig.type = SDW_STREAM_PDM;
-	pdev->prop.sink_ports = GENMASK(WSA881X_MAX_SWR_PORTS, 0);
+	pdev->prop.sink_ports = GENMASK(WSA881X_MAX_SWR_PORTS - 1, 0);
 	pdev->prop.sink_dpn_prop = wsa_sink_dpn_prop;
 	pdev->prop.scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY;
 	gpiod_direction_output(wsa881x->sd_n, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/dwc/dwc-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/dwc/dwc-i2s.c
@@ -132,13 +132,13 @@
 
 		/* Error Handling: TX */
 		if (isr[i] & ISR_TXFO) {
-			dev_err(dev->dev, "TX overrun (ch_id=%d)\n", i);
+			dev_err_ratelimited(dev->dev, "TX overrun (ch_id=%d)\n", i);
 			irq_valid = true;
 		}
 
 		/* Error Handling: TX */
 		if (isr[i] & ISR_RXFO) {
-			dev_err(dev->dev, "RX overrun (ch_id=%d)\n", i);
+			dev_err_ratelimited(dev->dev, "RX overrun (ch_id=%d)\n", i);
 			irq_valid = true;
 		}
 	}
@@ -183,30 +183,6 @@
 	}
 }
 
-static int dw_i2s_startup(struct snd_pcm_substream *substream,
-		struct snd_soc_dai *cpu_dai)
-{
-	struct dw_i2s_dev *dev = snd_soc_dai_get_drvdata(cpu_dai);
-	union dw_i2s_snd_dma_data *dma_data = NULL;
-
-	if (!(dev->capability & DWC_I2S_RECORD) &&
-			(substream->stream == SNDRV_PCM_STREAM_CAPTURE))
-		return -EINVAL;
-
-	if (!(dev->capability & DWC_I2S_PLAY) &&
-			(substream->stream == SNDRV_PCM_STREAM_PLAYBACK))
-		return -EINVAL;
-
-	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-		dma_data = &dev->play_dma_data;
-	else if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
-		dma_data = &dev->capture_dma_data;
-
-	snd_soc_dai_set_dma_data(cpu_dai, substream, (void *)dma_data);
-
-	return 0;
-}
-
 static void dw_i2s_config(struct dw_i2s_dev *dev, int stream)
 {
 	u32 ch_reg;
@@ -305,12 +281,6 @@
 	return 0;
 }
 
-static void dw_i2s_shutdown(struct snd_pcm_substream *substream,
-		struct snd_soc_dai *dai)
-{
-	snd_soc_dai_set_dma_data(dai, substream, NULL);
-}
-
 static int dw_i2s_prepare(struct snd_pcm_substream *substream,
 			  struct snd_soc_dai *dai)
 {
@@ -382,8 +352,6 @@
 }
 
 static const struct snd_soc_dai_ops dw_i2s_dai_ops = {
-	.startup	= dw_i2s_startup,
-	.shutdown	= dw_i2s_shutdown,
 	.hw_params	= dw_i2s_hw_params,
 	.prepare	= dw_i2s_prepare,
 	.trigger	= dw_i2s_trigger,
@@ -403,9 +371,13 @@
 static int dw_i2s_runtime_resume(struct device *dev)
 {
 	struct dw_i2s_dev *dw_dev = dev_get_drvdata(dev);
+	int ret;
 
-	if (dw_dev->capability & DW_I2S_MASTER)
-		clk_enable(dw_dev->clk);
+	if (dw_dev->capability & DW_I2S_MASTER) {
+		ret = clk_enable(dw_dev->clk);
+		if (ret)
+			return ret;
+	}
 	return 0;
 }
 
@@ -422,10 +394,13 @@
 {
 	struct dw_i2s_dev *dev = snd_soc_component_get_drvdata(component);
 	struct snd_soc_dai *dai;
-	int stream;
+	int stream, ret;
 
-	if (dev->capability & DW_I2S_MASTER)
-		clk_enable(dev->clk);
+	if (dev->capability & DW_I2S_MASTER) {
+		ret = clk_enable(dev->clk);
+		if (ret)
+			return ret;
+	}
 
 	for_each_component_dais(component, dai) {
 		for_each_pcm_streams(stream)
@@ -617,6 +592,14 @@
 
 }
 
+static int dw_i2s_dai_probe(struct snd_soc_dai *dai)
+{
+	struct dw_i2s_dev *dev = snd_soc_dai_get_drvdata(dai);
+
+	snd_soc_dai_init_dma_data(dai, &dev->play_dma_data, &dev->capture_dma_data);
+	return 0;
+}
+
 static int dw_i2s_probe(struct platform_device *pdev)
 {
 	const struct i2s_platform_data *pdata = pdev->dev.platform_data;
@@ -635,6 +618,7 @@
 		return -ENOMEM;
 
 	dw_i2s_dai->ops = &dw_i2s_dai_ops;
+	dw_i2s_dai->probe = dw_i2s_dai_probe;
 
 	dev->i2s_base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 	if (IS_ERR(dev->i2s_base))
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/eukrea-tlv320.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/eukrea-tlv320.c
@@ -86,7 +86,7 @@
 	int ret;
 	int int_port = 0, ext_port;
 	struct device_node *np = pdev->dev.of_node;
-	struct device_node *ssi_np = NULL, *codec_np = NULL;
+	struct device_node *ssi_np = NULL, *codec_np = NULL, *tmp_np = NULL;
 
 	eukrea_tlv320.dev = &pdev->dev;
 	if (np) {
@@ -143,7 +143,7 @@
 	}
 
 	if (machine_is_eukrea_cpuimx27() ||
-	    of_find_compatible_node(NULL, NULL, "fsl,imx21-audmux")) {
+	    (tmp_np = of_find_compatible_node(NULL, NULL, "fsl,imx21-audmux"))) {
 		imx_audmux_v1_configure_port(MX27_AUDMUX_HPCR1_SSI0,
 			IMX_AUDMUX_V1_PCR_SYN |
 			IMX_AUDMUX_V1_PCR_TFSDIR |
@@ -158,10 +158,11 @@
 			IMX_AUDMUX_V1_PCR_SYN |
 			IMX_AUDMUX_V1_PCR_RXDSEL(MX27_AUDMUX_HPCR1_SSI0)
 		);
+		of_node_put(tmp_np);
 	} else if (machine_is_eukrea_cpuimx25sd() ||
 		   machine_is_eukrea_cpuimx35sd() ||
 		   machine_is_eukrea_cpuimx51sd() ||
-		   of_find_compatible_node(NULL, NULL, "fsl,imx31-audmux")) {
+		   (tmp_np = of_find_compatible_node(NULL, NULL, "fsl,imx31-audmux"))) {
 		if (!np)
 			ext_port = machine_is_eukrea_cpuimx25sd() ?
 				4 : 3;
@@ -178,6 +179,7 @@
 			IMX_AUDMUX_V2_PTCR_SYN,
 			IMX_AUDMUX_V2_PDCR_RXDSEL(int_port)
 		);
+		of_node_put(tmp_np);
 	} else {
 		if (np) {
 			/* The eukrea,asoc-tlv320 driver was explicitly
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl-asoc-card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl-asoc-card.c
@@ -120,11 +120,11 @@
 
 static const struct snd_soc_dapm_route audio_map_ac97[] = {
 	/* 1st half -- Normal DAPM routes */
-	{"Playback",  NULL, "AC97 Playback"},
-	{"AC97 Capture",  NULL, "Capture"},
+	{"AC97 Playback",  NULL, "CPU AC97 Playback"},
+	{"CPU AC97 Capture",  NULL, "AC97 Capture"},
 	/* 2nd half -- ASRC DAPM routes */
-	{"AC97 Playback",  NULL, "ASRC-Playback"},
-	{"ASRC-Capture",  NULL, "AC97 Capture"},
+	{"CPU AC97 Playback",  NULL, "ASRC-Playback"},
+	{"ASRC-Capture",  NULL, "CPU AC97 Capture"},
 };
 
 static const struct snd_soc_dapm_route audio_map_tx[] = {
@@ -540,6 +540,7 @@
 	struct device *codec_dev = NULL;
 	const char *codec_dai_name;
 	const char *codec_dev_name;
+	u32 asrc_fmt = 0;
 	u32 width;
 	int ret;
 
@@ -547,6 +548,8 @@
 	if (!priv)
 		return -ENOMEM;
 
+	priv->pdev = pdev;
+
 	cpu_np = of_parse_phandle(np, "audio-cpu", 0);
 	/* Give a chance to old DT binding */
 	if (!cpu_np)
@@ -741,7 +744,6 @@
 	}
 
 	/* Initialize sound card */
-	priv->pdev = pdev;
 	priv->card.dev = &pdev->dev;
 	priv->card.owner = THIS_MODULE;
 	ret = snd_soc_of_parse_card_name(&priv->card, "model");
@@ -817,8 +819,8 @@
 			goto asrc_fail;
 		}
 
-		ret = of_property_read_u32(asrc_np, "fsl,asrc-format",
-					   &priv->asrc_format);
+		ret = of_property_read_u32(asrc_np, "fsl,asrc-format", &asrc_fmt);
+		priv->asrc_format = (__force snd_pcm_format_t)asrc_fmt;
 		if (ret) {
 			/* Fallback to old binding; translate to asrc_format */
 			ret = of_property_read_u32(asrc_np, "fsl,asrc-width",
@@ -842,8 +844,7 @@
 
 	ret = devm_snd_soc_register_card(&pdev->dev, &priv->card);
 	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed\n");
 		goto asrc_fail;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_asrc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_asrc.c
@@ -19,6 +19,7 @@
 #include "fsl_asrc.h"
 
 #define IDEAL_RATIO_DECIMAL_DEPTH 26
+#define DIVIDER_NUM  64
 
 #define pair_err(fmt, ...) \
 	dev_err(&asrc->pdev->dev, "Pair %c: " fmt, 'A' + index, ##__VA_ARGS__)
@@ -101,6 +102,55 @@
 	},
 };
 
+/*
+ * According to RM, the divider range is 1 ~ 8,
+ * prescaler is power of 2 from 1 ~ 128.
+ */
+static int asrc_clk_divider[DIVIDER_NUM] = {
+	1,  2,  4,  8,  16,  32,  64,  128,  /* divider = 1 */
+	2,  4,  8, 16,  32,  64, 128,  256,  /* divider = 2 */
+	3,  6, 12, 24,  48,  96, 192,  384,  /* divider = 3 */
+	4,  8, 16, 32,  64, 128, 256,  512,  /* divider = 4 */
+	5, 10, 20, 40,  80, 160, 320,  640,  /* divider = 5 */
+	6, 12, 24, 48,  96, 192, 384,  768,  /* divider = 6 */
+	7, 14, 28, 56, 112, 224, 448,  896,  /* divider = 7 */
+	8, 16, 32, 64, 128, 256, 512, 1024,  /* divider = 8 */
+};
+
+/*
+ * Check if the divider is available for internal ratio mode
+ */
+static bool fsl_asrc_divider_avail(int clk_rate, int rate, int *div)
+{
+	u32 rem, i;
+	u64 n;
+
+	if (div)
+		*div = 0;
+
+	if (clk_rate == 0 || rate == 0)
+		return false;
+
+	n = clk_rate;
+	rem = do_div(n, rate);
+
+	if (div)
+		*div = n;
+
+	if (rem != 0)
+		return false;
+
+	for (i = 0; i < DIVIDER_NUM; i++) {
+		if (n == asrc_clk_divider[i])
+			break;
+	}
+
+	if (i == DIVIDER_NUM)
+		return false;
+
+	return true;
+}
+
 /**
  * fsl_asrc_sel_proc - Select the pre-processing and post-processing options
  * @inrate: input sample rate
@@ -330,12 +380,12 @@
 	enum asrc_word_width input_word_width;
 	enum asrc_word_width output_word_width;
 	u32 inrate, outrate, indiv, outdiv;
-	u32 clk_index[2], div[2], rem[2];
+	u32 clk_index[2], div[2];
 	u64 clk_rate;
 	int in, out, channels;
 	int pre_proc, post_proc;
 	struct clk *clk;
-	bool ideal;
+	bool ideal, div_avail;
 
 	if (!config) {
 		pair_err("invalid pair config\n");
@@ -415,8 +465,7 @@
 	clk = asrc_priv->asrck_clk[clk_index[ideal ? OUT : IN]];
 
 	clk_rate = clk_get_rate(clk);
-	rem[IN] = do_div(clk_rate, inrate);
-	div[IN] = (u32)clk_rate;
+	div_avail = fsl_asrc_divider_avail(clk_rate, inrate, &div[IN]);
 
 	/*
 	 * The divider range is [1, 1024], defined by the hardware. For non-
@@ -425,7 +474,7 @@
 	 * only result in different converting speeds. So remainder does not
 	 * matter, as long as we keep the divider within its valid range.
 	 */
-	if (div[IN] == 0 || (!ideal && (div[IN] > 1024 || rem[IN] != 0))) {
+	if (div[IN] == 0 || (!ideal && !div_avail)) {
 		pair_err("failed to support input sample rate %dHz by asrck_%x\n",
 				inrate, clk_index[ideal ? OUT : IN]);
 		return -EINVAL;
@@ -436,13 +485,12 @@
 	clk = asrc_priv->asrck_clk[clk_index[OUT]];
 	clk_rate = clk_get_rate(clk);
 	if (ideal && use_ideal_rate)
-		rem[OUT] = do_div(clk_rate, IDEAL_RATIO_RATE);
+		div_avail = fsl_asrc_divider_avail(clk_rate, IDEAL_RATIO_RATE, &div[OUT]);
 	else
-		rem[OUT] = do_div(clk_rate, outrate);
-	div[OUT] = clk_rate;
+		div_avail = fsl_asrc_divider_avail(clk_rate, outrate, &div[OUT]);
 
 	/* Output divider has the same limitation as the input one */
-	if (div[OUT] == 0 || (!ideal && (div[OUT] > 1024 || rem[OUT] != 0))) {
+	if (div[OUT] == 0 || (!ideal && !div_avail)) {
 		pair_err("failed to support output sample rate %dHz by asrck_%x\n",
 				outrate, clk_index[OUT]);
 		return -EINVAL;
@@ -621,8 +669,7 @@
 			clk_index = asrc_priv->clk_map[j][i];
 			clk_rate = clk_get_rate(asrc_priv->asrck_clk[clk_index]);
 			/* Only match a perfect clock source with no remainder */
-			if (clk_rate != 0 && (clk_rate / rate[j]) <= 1024 &&
-			    (clk_rate % rate[j]) == 0)
+			if (fsl_asrc_divider_avail(clk_rate, rate[j], NULL))
 				break;
 		}
 
@@ -1019,6 +1066,7 @@
 	struct resource *res;
 	void __iomem *regs;
 	int irq, ret, i;
+	u32 asrc_fmt = 0;
 	u32 map_idx;
 	char tmp[16];
 	u32 width;
@@ -1127,7 +1175,8 @@
 		return ret;
 	}
 
-	ret = of_property_read_u32(np, "fsl,asrc-format", &asrc->asrc_format);
+	ret = of_property_read_u32(np, "fsl,asrc-format", &asrc_fmt);
+	asrc->asrc_format = (__force snd_pcm_format_t)asrc_fmt;
 	if (ret) {
 		ret = of_property_read_u32(np, "fsl,asrc-width", &width);
 		if (ret) {
@@ -1150,7 +1199,7 @@
 		}
 	}
 
-	if (!(FSL_ASRC_FORMATS & (1ULL << asrc->asrc_format))) {
+	if (!(FSL_ASRC_FORMATS & pcm_format_to_bits(asrc->asrc_format))) {
 		dev_warn(&pdev->dev, "unsupported width, use default S24_LE\n");
 		asrc->asrc_format = SNDRV_PCM_FORMAT_S24_LE;
 	}
@@ -1177,7 +1226,7 @@
 	}
 
 	ret = pm_runtime_put_sync(&pdev->dev);
-	if (ret < 0)
+	if (ret < 0 && ret != -ENOSYS)
 		goto err_pm_get_sync;
 
 	ret = devm_snd_soc_register_component(&pdev->dev, &fsl_asrc_component,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_asrc_dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_asrc_dma.c
@@ -208,14 +208,19 @@
 		be_chan = soc_component_to_pcm(component_be)->chan[substream->stream];
 		tmp_chan = be_chan;
 	}
-	if (!tmp_chan)
-		tmp_chan = dma_request_slave_channel(dev_be, tx ? "tx" : "rx");
+	if (!tmp_chan) {
+		tmp_chan = dma_request_chan(dev_be, tx ? "tx" : "rx");
+		if (IS_ERR(tmp_chan)) {
+			dev_err(dev, "failed to request DMA channel for Back-End\n");
+			return -EINVAL;
+		}
+	}
 
 	/*
 	 * An EDMA DEV_TO_DEV channel is fixed and bound with DMA event of each
 	 * peripheral, unlike SDMA channel that is allocated dynamically. So no
 	 * need to configure dma_request and dma_request2, but get dma_chan of
-	 * Back-End device directly via dma_request_slave_channel.
+	 * Back-End device directly via dma_request_chan.
 	 */
 	if (!asrc->use_edma) {
 		/* Get DMA request of Back-End */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_easrc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_easrc.c
@@ -476,7 +476,8 @@
 	struct fsl_asrc_pair *ctx;
 	struct device *dev;
 	u32 inrate, outrate, offset = 0;
-	u32 in_s_rate, out_s_rate, in_s_fmt, out_s_fmt;
+	u32 in_s_rate, out_s_rate;
+	snd_pcm_format_t in_s_fmt, out_s_fmt;
 	int ret, i;
 
 	if (!easrc)
@@ -1873,6 +1874,7 @@
 	struct resource *res;
 	struct device_node *np;
 	void __iomem *regs;
+	u32 asrc_fmt = 0;
 	int ret, irq;
 
 	easrc = devm_kzalloc(dev, sizeof(*easrc), GFP_KERNEL);
@@ -1933,13 +1935,14 @@
 		return ret;
 	}
 
-	ret = of_property_read_u32(np, "fsl,asrc-format", &easrc->asrc_format);
+	ret = of_property_read_u32(np, "fsl,asrc-format", &asrc_fmt);
+	easrc->asrc_format = (__force snd_pcm_format_t)asrc_fmt;
 	if (ret) {
 		dev_err(dev, "failed to asrc format\n");
 		return ret;
 	}
 
-	if (!(FSL_EASRC_FORMATS & (1ULL << easrc->asrc_format))) {
+	if (!(FSL_EASRC_FORMATS & (pcm_format_to_bits(easrc->asrc_format)))) {
 		dev_warn(dev, "unsupported format, switching to S24_LE\n");
 		easrc->asrc_format = SNDRV_PCM_FORMAT_S24_LE;
 	}
@@ -1962,17 +1965,21 @@
 					      &fsl_easrc_dai, 1);
 	if (ret) {
 		dev_err(dev, "failed to register ASoC DAI\n");
-		return ret;
+		goto err_pm_disable;
 	}
 
 	ret = devm_snd_soc_register_component(dev, &fsl_asrc_component,
 					      NULL, 0);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register ASoC platform\n");
-		return ret;
+		goto err_pm_disable;
 	}
 
 	return 0;
+
+err_pm_disable:
+	pm_runtime_disable(&pdev->dev);
+	return ret;
 }
 
 static int fsl_easrc_remove(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_easrc.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_easrc.h
@@ -569,7 +569,7 @@
 	unsigned int access_len;
 	unsigned int fifo_wtmk;
 	unsigned int sample_rate;
-	unsigned int sample_format;
+	snd_pcm_format_t sample_format;
 	unsigned int norm_rate;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_esai.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_esai.c
@@ -1070,7 +1070,7 @@
 	regmap_write(esai_priv->regmap, REG_ESAI_RSMB, 0);
 
 	ret = pm_runtime_put_sync(&pdev->dev);
-	if (ret < 0)
+	if (ret < 0 && ret != -ENOSYS)
 		goto err_pm_get_sync;
 
 	/*
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_micfil.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_micfil.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 // Copyright 2018 NXP
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/device.h>
 #include <linux/interrupt.h>
@@ -88,21 +89,21 @@
 
 static const struct snd_kcontrol_new fsl_micfil_snd_controls[] = {
 	SOC_SINGLE_SX_TLV("CH0 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(0), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(0), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH1 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(1), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(1), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH2 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(2), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(2), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH3 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(3), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(3), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH4 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(4), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(4), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH5 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(5), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(5), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH6 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(6), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(6), 0x8, 0xF, gain_tlv),
 	SOC_SINGLE_SX_TLV("CH7 Volume", REG_MICFIL_OUT_CTRL,
-			  MICFIL_OUTGAIN_CHX_SHIFT(7), 0xF, 0x7, gain_tlv),
+			  MICFIL_OUTGAIN_CHX_SHIFT(7), 0x8, 0xF, gain_tlv),
 	SOC_ENUM_EXT("MICFIL Quality Select",
 		     fsl_micfil_quality_enum,
 		     snd_soc_get_enum_double, snd_soc_put_enum_double),
@@ -116,25 +117,22 @@
 	int bclk;
 
 	regmap_read(micfil->regmap, REG_MICFIL_CTRL2, &ctrl2_reg);
-	osr = 16 - ((ctrl2_reg & MICFIL_CTRL2_CICOSR_MASK)
-		    >> MICFIL_CTRL2_CICOSR_SHIFT);
-
-	regmap_read(micfil->regmap, REG_MICFIL_CTRL2, &ctrl2_reg);
-	qsel = ctrl2_reg & MICFIL_CTRL2_QSEL_MASK;
+	osr = 16 - FIELD_GET(MICFIL_CTRL2_CICOSR, ctrl2_reg);
+	qsel = FIELD_GET(MICFIL_CTRL2_QSEL, ctrl2_reg);
 
 	switch (qsel) {
-	case MICFIL_HIGH_QUALITY:
+	case MICFIL_QSEL_HIGH_QUALITY:
 		bclk = rate * 8 * osr / 2; /* kfactor = 0.5 */
 		break;
-	case MICFIL_MEDIUM_QUALITY:
-	case MICFIL_VLOW0_QUALITY:
+	case MICFIL_QSEL_MEDIUM_QUALITY:
+	case MICFIL_QSEL_VLOW0_QUALITY:
 		bclk = rate * 4 * osr * 1; /* kfactor = 1 */
 		break;
-	case MICFIL_LOW_QUALITY:
-	case MICFIL_VLOW1_QUALITY:
+	case MICFIL_QSEL_LOW_QUALITY:
+	case MICFIL_QSEL_VLOW1_QUALITY:
 		bclk = rate * 2 * osr * 2; /* kfactor = 2 */
 		break;
-	case MICFIL_VLOW2_QUALITY:
+	case MICFIL_QSEL_VLOW2_QUALITY:
 		bclk = rate * osr * 4; /* kfactor = 4 */
 		break;
 	default:
@@ -175,7 +173,7 @@
 
 	ret = regmap_update_bits(micfil->regmap,
 				 REG_MICFIL_CTRL1,
-				 MICFIL_CTRL1_MDIS_MASK,
+				 MICFIL_CTRL1_MDIS,
 				 0);
 	if (ret) {
 		dev_err(dev, "failed to clear MDIS bit %d\n", ret);
@@ -184,13 +182,32 @@
 
 	ret = regmap_update_bits(micfil->regmap,
 				 REG_MICFIL_CTRL1,
-				 MICFIL_CTRL1_SRES_MASK,
+				 MICFIL_CTRL1_SRES,
 				 MICFIL_CTRL1_SRES);
 	if (ret) {
 		dev_err(dev, "failed to reset MICFIL: %d\n", ret);
 		return ret;
 	}
 
+	/*
+	 * SRES is self-cleared bit, but REG_MICFIL_CTRL1 is defined
+	 * as non-volatile register, so SRES still remain in regmap
+	 * cache after set, that every update of REG_MICFIL_CTRL1,
+	 * software reset happens. so clear it explicitly.
+	 */
+	ret = regmap_clear_bits(micfil->regmap, REG_MICFIL_CTRL1,
+				MICFIL_CTRL1_SRES);
+	if (ret)
+		return ret;
+
+	/*
+	 * Set SRES should clear CHnF flags, But even add delay here
+	 * the CHnF may not be cleared sometimes, so clear CHnF explicitly.
+	 */
+	ret = regmap_write_bits(micfil->regmap, REG_MICFIL_STAT, 0xFF, 0xFF);
+	if (ret)
+		return ret;
+
 	return 0;
 }
 
@@ -249,8 +266,8 @@
 		 * 11 - reserved
 		 */
 		ret = regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL1,
-					 MICFIL_CTRL1_DISEL_MASK,
-					 (1 << MICFIL_CTRL1_DISEL_SHIFT));
+				MICFIL_CTRL1_DISEL,
+				FIELD_PREP(MICFIL_CTRL1_DISEL, MICFIL_CTRL1_DISEL_DMA));
 		if (ret) {
 			dev_err(dev, "failed to update DISEL bits\n");
 			return ret;
@@ -258,7 +275,7 @@
 
 		/* Enable the module */
 		ret = regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL1,
-					 MICFIL_CTRL1_PDMIEN_MASK,
+					 MICFIL_CTRL1_PDMIEN,
 					 MICFIL_CTRL1_PDMIEN);
 		if (ret) {
 			dev_err(dev, "failed to enable the module\n");
@@ -271,7 +288,7 @@
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
 		/* Disable the module */
 		ret = regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL1,
-					 MICFIL_CTRL1_PDMIEN_MASK,
+					 MICFIL_CTRL1_PDMIEN,
 					 0);
 		if (ret) {
 			dev_err(dev, "failed to enable the module\n");
@@ -279,8 +296,8 @@
 		}
 
 		ret = regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL1,
-					 MICFIL_CTRL1_DISEL_MASK,
-					 (0 << MICFIL_CTRL1_DISEL_SHIFT));
+				MICFIL_CTRL1_DISEL,
+				FIELD_PREP(MICFIL_CTRL1_DISEL, MICFIL_CTRL1_DISEL_DISABLE));
 		if (ret) {
 			dev_err(dev, "failed to update DISEL bits\n");
 			return ret;
@@ -305,8 +322,8 @@
 
 	/* set CICOSR */
 	ret |= regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL2,
-				 MICFIL_CTRL2_CICOSR_MASK,
-				 MICFIL_CTRL2_OSR_DEFAULT);
+				 MICFIL_CTRL2_CICOSR,
+				 FIELD_PREP(MICFIL_CTRL2_CICOSR, MICFIL_CTRL2_CICOSR_DEFAULT));
 	if (ret)
 		dev_err(dev, "failed to set CICOSR in reg 0x%X\n",
 			REG_MICFIL_CTRL2);
@@ -317,7 +334,8 @@
 		ret = -EINVAL;
 
 	ret |= regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL2,
-				 MICFIL_CTRL2_CLKDIV_MASK, clk_div);
+				 MICFIL_CTRL2_CLKDIV,
+				 FIELD_PREP(MICFIL_CTRL2_CLKDIV, clk_div));
 	if (ret)
 		dev_err(dev, "failed to set CLKDIV in reg 0x%X\n",
 			REG_MICFIL_CTRL2);
@@ -337,7 +355,7 @@
 
 	/* 1. Disable the module */
 	ret = regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL1,
-				 MICFIL_CTRL1_PDMIEN_MASK, 0);
+				 MICFIL_CTRL1_PDMIEN, 0);
 	if (ret) {
 		dev_err(dev, "failed to disable the module\n");
 		return ret;
@@ -393,13 +411,13 @@
 {
 	struct fsl_micfil *micfil = dev_get_drvdata(cpu_dai->dev);
 	struct device *dev = cpu_dai->dev;
-	unsigned int val;
 	int ret;
 	int i;
 
 	/* set qsel to medium */
 	ret = regmap_update_bits(micfil->regmap, REG_MICFIL_CTRL2,
-				 MICFIL_CTRL2_QSEL_MASK, MICFIL_MEDIUM_QUALITY);
+			MICFIL_CTRL2_QSEL,
+			FIELD_PREP(MICFIL_CTRL2_QSEL, MICFIL_QSEL_MEDIUM_QUALITY));
 	if (ret) {
 		dev_err(dev, "failed to set quality mode bits, reg 0x%X\n",
 			REG_MICFIL_CTRL2);
@@ -415,10 +433,9 @@
 				  &micfil->dma_params_rx);
 
 	/* FIFO Watermark Control - FIFOWMK*/
-	val = MICFIL_FIFO_CTRL_FIFOWMK(micfil->soc->fifo_depth) - 1;
 	ret = regmap_update_bits(micfil->regmap, REG_MICFIL_FIFO_CTRL,
-				 MICFIL_FIFO_CTRL_FIFOWMK_MASK,
-				 val);
+			MICFIL_FIFO_CTRL_FIFOWMK,
+			FIELD_PREP(MICFIL_FIFO_CTRL_FIFOWMK, micfil->soc->fifo_depth - 1));
 	if (ret) {
 		dev_err(dev, "failed to set FIFOWMK\n");
 		return ret;
@@ -578,11 +595,11 @@
 	regmap_read(micfil->regmap, REG_MICFIL_CTRL1, &ctrl1_reg);
 	regmap_read(micfil->regmap, REG_MICFIL_FIFO_STAT, &fifo_stat_reg);
 
-	dma_enabled = MICFIL_DMA_ENABLED(ctrl1_reg);
+	dma_enabled = FIELD_GET(MICFIL_CTRL1_DISEL, ctrl1_reg) == MICFIL_CTRL1_DISEL_DMA;
 
 	/* Channel 0-7 Output Data Flags */
 	for (i = 0; i < MICFIL_OUTPUT_CHANNELS; i++) {
-		if (stat_reg & MICFIL_STAT_CHXF_MASK(i))
+		if (stat_reg & MICFIL_STAT_CHXF(i))
 			dev_dbg(&pdev->dev,
 				"Data available in Data Channel %d\n", i);
 		/* if DMA is not enabled, field must be written with 1
@@ -591,17 +608,17 @@
 		if (!dma_enabled)
 			regmap_write_bits(micfil->regmap,
 					  REG_MICFIL_STAT,
-					  MICFIL_STAT_CHXF_MASK(i),
-					  1);
+					  MICFIL_STAT_CHXF(i),
+					  MICFIL_STAT_CHXF(i));
 	}
 
 	for (i = 0; i < MICFIL_FIFO_NUM; i++) {
-		if (fifo_stat_reg & MICFIL_FIFO_STAT_FIFOX_OVER_MASK(i))
+		if (fifo_stat_reg & MICFIL_FIFO_STAT_FIFOX_OVER(i))
 			dev_dbg(&pdev->dev,
 				"FIFO Overflow Exception flag for channel %d\n",
 				i);
 
-		if (fifo_stat_reg & MICFIL_FIFO_STAT_FIFOX_UNDER_MASK(i))
+		if (fifo_stat_reg & MICFIL_FIFO_STAT_FIFOX_UNDER(i))
 			dev_dbg(&pdev->dev,
 				"FIFO Underflow Exception flag for channel %d\n",
 				i);
@@ -618,16 +635,16 @@
 
 	regmap_read(micfil->regmap, REG_MICFIL_STAT, &stat_reg);
 
-	if (stat_reg & MICFIL_STAT_BSY_FIL_MASK)
+	if (stat_reg & MICFIL_STAT_BSY_FIL)
 		dev_dbg(&pdev->dev, "isr: Decimation Filter is running\n");
 
-	if (stat_reg & MICFIL_STAT_FIR_RDY_MASK)
+	if (stat_reg & MICFIL_STAT_FIR_RDY)
 		dev_dbg(&pdev->dev, "isr: FIR Filter Data ready\n");
 
-	if (stat_reg & MICFIL_STAT_LOWFREQF_MASK) {
+	if (stat_reg & MICFIL_STAT_LOWFREQF) {
 		dev_dbg(&pdev->dev, "isr: ipg_clk_app is too low\n");
 		regmap_write_bits(micfil->regmap, REG_MICFIL_STAT,
-				  MICFIL_STAT_LOWFREQF_MASK, 1);
+				  MICFIL_STAT_LOWFREQF, MICFIL_STAT_LOWFREQF);
 	}
 
 	return IRQ_HANDLED;
@@ -744,7 +761,7 @@
 	ret = devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to pcm register\n");
-		return ret;
+		goto err_pm_disable;
 	}
 
 	ret = devm_snd_soc_register_component(&pdev->dev, &fsl_micfil_component,
@@ -752,9 +769,20 @@
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register component %s\n",
 			fsl_micfil_component.name);
+		goto err_pm_disable;
 	}
 
 	return ret;
+
+err_pm_disable:
+	pm_runtime_disable(&pdev->dev);
+
+	return ret;
+}
+
+static void fsl_micfil_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
 }
 
 static int __maybe_unused fsl_micfil_runtime_suspend(struct device *dev)
@@ -815,6 +843,7 @@
 
 static struct platform_driver fsl_micfil_driver = {
 	.probe = fsl_micfil_probe,
+	.remove_new = fsl_micfil_remove,
 	.driver = {
 		.name = "fsl-micfil-dai",
 		.pm = &fsl_micfil_pm_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_micfil.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_micfil.h
@@ -33,240 +33,95 @@
 #define REG_MICFIL_VAD0_ZCD		0xA8
 
 /* MICFIL Control Register 1 -- REG_MICFILL_CTRL1 0x00 */
-#define MICFIL_CTRL1_MDIS_SHIFT		31
-#define MICFIL_CTRL1_MDIS_MASK		BIT(MICFIL_CTRL1_MDIS_SHIFT)
-#define MICFIL_CTRL1_MDIS		BIT(MICFIL_CTRL1_MDIS_SHIFT)
-#define MICFIL_CTRL1_DOZEN_SHIFT	30
-#define MICFIL_CTRL1_DOZEN_MASK		BIT(MICFIL_CTRL1_DOZEN_SHIFT)
-#define MICFIL_CTRL1_DOZEN		BIT(MICFIL_CTRL1_DOZEN_SHIFT)
-#define MICFIL_CTRL1_PDMIEN_SHIFT	29
-#define MICFIL_CTRL1_PDMIEN_MASK	BIT(MICFIL_CTRL1_PDMIEN_SHIFT)
-#define MICFIL_CTRL1_PDMIEN		BIT(MICFIL_CTRL1_PDMIEN_SHIFT)
-#define MICFIL_CTRL1_DBG_SHIFT		28
-#define MICFIL_CTRL1_DBG_MASK		BIT(MICFIL_CTRL1_DBG_SHIFT)
-#define MICFIL_CTRL1_DBG		BIT(MICFIL_CTRL1_DBG_SHIFT)
-#define MICFIL_CTRL1_SRES_SHIFT		27
-#define MICFIL_CTRL1_SRES_MASK		BIT(MICFIL_CTRL1_SRES_SHIFT)
-#define MICFIL_CTRL1_SRES		BIT(MICFIL_CTRL1_SRES_SHIFT)
-#define MICFIL_CTRL1_DBGE_SHIFT		26
-#define MICFIL_CTRL1_DBGE_MASK		BIT(MICFIL_CTRL1_DBGE_SHIFT)
-#define MICFIL_CTRL1_DBGE		BIT(MICFIL_CTRL1_DBGE_SHIFT)
-#define MICFIL_CTRL1_DISEL_SHIFT	24
-#define MICFIL_CTRL1_DISEL_WIDTH	2
-#define MICFIL_CTRL1_DISEL_MASK		((BIT(MICFIL_CTRL1_DISEL_WIDTH) - 1) \
-					 << MICFIL_CTRL1_DISEL_SHIFT)
-#define MICFIL_CTRL1_DISEL(v)		(((v) << MICFIL_CTRL1_DISEL_SHIFT) \
-					 & MICFIL_CTRL1_DISEL_MASK)
-#define MICFIL_CTRL1_ERREN_SHIFT	23
-#define MICFIL_CTRL1_ERREN_MASK		BIT(MICFIL_CTRL1_ERREN_SHIFT)
-#define MICFIL_CTRL1_ERREN		BIT(MICFIL_CTRL1_ERREN_SHIFT)
-#define MICFIL_CTRL1_CHEN_SHIFT		0
-#define MICFIL_CTRL1_CHEN_WIDTH		8
-#define MICFIL_CTRL1_CHEN_MASK(x)	(BIT(x) << MICFIL_CTRL1_CHEN_SHIFT)
-#define MICFIL_CTRL1_CHEN(x)		(MICFIL_CTRL1_CHEN_MASK(x))
+#define MICFIL_CTRL1_MDIS		BIT(31)
+#define MICFIL_CTRL1_DOZEN		BIT(30)
+#define MICFIL_CTRL1_PDMIEN		BIT(29)
+#define MICFIL_CTRL1_DBG		BIT(28)
+#define MICFIL_CTRL1_SRES		BIT(27)
+#define MICFIL_CTRL1_DBGE		BIT(26)
+
+#define MICFIL_CTRL1_DISEL_DISABLE	0
+#define MICFIL_CTRL1_DISEL_DMA		1
+#define MICFIL_CTRL1_DISEL_IRQ		2
+#define MICFIL_CTRL1_DISEL		GENMASK(25, 24)
+#define MICFIL_CTRL1_ERREN		BIT(23)
+#define MICFIL_CTRL1_CHEN(ch)		BIT(ch)
 
 /* MICFIL Control Register 2 -- REG_MICFILL_CTRL2 0x04 */
 #define MICFIL_CTRL2_QSEL_SHIFT		25
-#define MICFIL_CTRL2_QSEL_WIDTH		3
-#define MICFIL_CTRL2_QSEL_MASK		((BIT(MICFIL_CTRL2_QSEL_WIDTH) - 1) \
-					 << MICFIL_CTRL2_QSEL_SHIFT)
-#define MICFIL_HIGH_QUALITY		BIT(MICFIL_CTRL2_QSEL_SHIFT)
-#define MICFIL_MEDIUM_QUALITY		(0 << MICFIL_CTRL2_QSEL_SHIFT)
-#define MICFIL_LOW_QUALITY		(7 << MICFIL_CTRL2_QSEL_SHIFT)
-#define MICFIL_VLOW0_QUALITY		(6 << MICFIL_CTRL2_QSEL_SHIFT)
-#define MICFIL_VLOW1_QUALITY		(5 << MICFIL_CTRL2_QSEL_SHIFT)
-#define MICFIL_VLOW2_QUALITY		(4 << MICFIL_CTRL2_QSEL_SHIFT)
-
-#define MICFIL_CTRL2_CICOSR_SHIFT	16
-#define MICFIL_CTRL2_CICOSR_WIDTH	4
-#define MICFIL_CTRL2_CICOSR_MASK	((BIT(MICFIL_CTRL2_CICOSR_WIDTH) - 1) \
-					 << MICFIL_CTRL2_CICOSR_SHIFT)
-#define MICFIL_CTRL2_CICOSR(v)		(((v) << MICFIL_CTRL2_CICOSR_SHIFT) \
-					 & MICFIL_CTRL2_CICOSR_MASK)
-#define MICFIL_CTRL2_CLKDIV_SHIFT	0
-#define MICFIL_CTRL2_CLKDIV_WIDTH	8
-#define MICFIL_CTRL2_CLKDIV_MASK	((BIT(MICFIL_CTRL2_CLKDIV_WIDTH) - 1) \
-					 << MICFIL_CTRL2_CLKDIV_SHIFT)
-#define MICFIL_CTRL2_CLKDIV(v)		(((v) << MICFIL_CTRL2_CLKDIV_SHIFT) \
-					 & MICFIL_CTRL2_CLKDIV_MASK)
+#define MICFIL_CTRL2_QSEL		GENMASK(27, 25)
+#define MICFIL_QSEL_MEDIUM_QUALITY	0
+#define MICFIL_QSEL_HIGH_QUALITY	1
+#define MICFIL_QSEL_LOW_QUALITY		7
+#define MICFIL_QSEL_VLOW0_QUALITY	6
+#define MICFIL_QSEL_VLOW1_QUALITY	5
+#define MICFIL_QSEL_VLOW2_QUALITY	4
+
+#define MICFIL_CTRL2_CICOSR		GENMASK(19, 16)
+#define MICFIL_CTRL2_CICOSR_DEFAULT	0
+#define MICFIL_CTRL2_CLKDIV		GENMASK(7, 0)
 
 /* MICFIL Status Register -- REG_MICFIL_STAT 0x08 */
-#define MICFIL_STAT_BSY_FIL_SHIFT	31
-#define MICFIL_STAT_BSY_FIL_MASK	BIT(MICFIL_STAT_BSY_FIL_SHIFT)
-#define MICFIL_STAT_BSY_FIL		BIT(MICFIL_STAT_BSY_FIL_SHIFT)
-#define MICFIL_STAT_FIR_RDY_SHIFT	30
-#define MICFIL_STAT_FIR_RDY_MASK	BIT(MICFIL_STAT_FIR_RDY_SHIFT)
-#define MICFIL_STAT_FIR_RDY		BIT(MICFIL_STAT_FIR_RDY_SHIFT)
-#define MICFIL_STAT_LOWFREQF_SHIFT	29
-#define MICFIL_STAT_LOWFREQF_MASK	BIT(MICFIL_STAT_LOWFREQF_SHIFT)
-#define MICFIL_STAT_LOWFREQF		BIT(MICFIL_STAT_LOWFREQF_SHIFT)
-#define MICFIL_STAT_CHXF_SHIFT(v)	(v)
-#define MICFIL_STAT_CHXF_MASK(v)	BIT(MICFIL_STAT_CHXF_SHIFT(v))
-#define MICFIL_STAT_CHXF(v)		BIT(MICFIL_STAT_CHXF_SHIFT(v))
+#define MICFIL_STAT_BSY_FIL		BIT(31)
+#define MICFIL_STAT_FIR_RDY		BIT(30)
+#define MICFIL_STAT_LOWFREQF		BIT(29)
+#define MICFIL_STAT_CHXF(ch)		BIT(ch)
 
 /* MICFIL FIFO Control Register -- REG_MICFIL_FIFO_CTRL 0x10 */
-#define MICFIL_FIFO_CTRL_FIFOWMK_SHIFT	0
-#define MICFIL_FIFO_CTRL_FIFOWMK_WIDTH	3
-#define MICFIL_FIFO_CTRL_FIFOWMK_MASK	((BIT(MICFIL_FIFO_CTRL_FIFOWMK_WIDTH) - 1) \
-					 << MICFIL_FIFO_CTRL_FIFOWMK_SHIFT)
-#define MICFIL_FIFO_CTRL_FIFOWMK(v)	(((v) << MICFIL_FIFO_CTRL_FIFOWMK_SHIFT) \
-					 & MICFIL_FIFO_CTRL_FIFOWMK_MASK)
+#define MICFIL_FIFO_CTRL_FIFOWMK	GENMASK(2, 0)
 
 /* MICFIL FIFO Status Register -- REG_MICFIL_FIFO_STAT 0x14 */
-#define MICFIL_FIFO_STAT_FIFOX_OVER_SHIFT(v)	(v)
-#define MICFIL_FIFO_STAT_FIFOX_OVER_MASK(v)	BIT(MICFIL_FIFO_STAT_FIFOX_OVER_SHIFT(v))
-#define MICFIL_FIFO_STAT_FIFOX_UNDER_SHIFT(v)	((v) + 8)
-#define MICFIL_FIFO_STAT_FIFOX_UNDER_MASK(v)	BIT(MICFIL_FIFO_STAT_FIFOX_UNDER_SHIFT(v))
+#define MICFIL_FIFO_STAT_FIFOX_OVER(ch)	BIT(ch)
+#define MICFIL_FIFO_STAT_FIFOX_UNDER(ch)	BIT((ch) + 8)
 
 /* MICFIL HWVAD0 Control 1 Register -- REG_MICFIL_VAD0_CTRL1*/
-#define MICFIL_VAD0_CTRL1_CHSEL_SHIFT	24
-#define MICFIL_VAD0_CTRL1_CHSEL_WIDTH	3
-#define MICFIL_VAD0_CTRL1_CHSEL_MASK	((BIT(MICFIL_VAD0_CTRL1_CHSEL_WIDTH) - 1) \
-					 << MICFIL_VAD0_CTRL1_CHSEL_SHIFT)
-#define MICFIL_VAD0_CTRL1_CHSEL(v)	(((v) << MICFIL_VAD0_CTRL1_CHSEL_SHIFT) \
-					 & MICFIL_VAD0_CTRL1_CHSEL_MASK)
-#define MICFIL_VAD0_CTRL1_CICOSR_SHIFT	16
-#define MICFIL_VAD0_CTRL1_CICOSR_WIDTH	4
-#define MICFIL_VAD0_CTRL1_CICOSR_MASK	((BIT(MICFIL_VAD0_CTRL1_CICOSR_WIDTH) - 1) \
-					 << MICFIL_VAD0_CTRL1_CICOSR_SHIFT)
-#define MICFIL_VAD0_CTRL1_CICOSR(v)	(((v) << MICFIL_VAD0_CTRL1_CICOSR_SHIFT) \
-					 & MICFIL_VAD0_CTRL1_CICOSR_MASK)
-#define MICFIL_VAD0_CTRL1_INITT_SHIFT	8
-#define MICFIL_VAD0_CTRL1_INITT_WIDTH	5
-#define MICFIL_VAD0_CTRL1_INITT_MASK	((BIT(MICFIL_VAD0_CTRL1_INITT_WIDTH) - 1) \
-					 << MICFIL_VAD0_CTRL1_INITT_SHIFT)
-#define MICFIL_VAD0_CTRL1_INITT(v)	(((v) << MICFIL_VAD0_CTRL1_INITT_SHIFT) \
-					 & MICFIL_VAD0_CTRL1_INITT_MASK)
-#define MICFIL_VAD0_CTRL1_ST10_SHIFT	4
-#define MICFIL_VAD0_CTRL1_ST10_MASK	BIT(MICFIL_VAD0_CTRL1_ST10_SHIFT)
-#define MICFIL_VAD0_CTRL1_ST10		BIT(MICFIL_VAD0_CTRL1_ST10_SHIFT)
-#define MICFIL_VAD0_CTRL1_ERIE_SHIFT	3
-#define MICFIL_VAD0_CTRL1_ERIE_MASK	BIT(MICFIL_VAD0_CTRL1_ERIE_SHIFT)
-#define MICFIL_VAD0_CTRL1_ERIE		BIT(MICFIL_VAD0_CTRL1_ERIE_SHIFT)
-#define MICFIL_VAD0_CTRL1_IE_SHIFT	2
-#define MICFIL_VAD0_CTRL1_IE_MASK	BIT(MICFIL_VAD0_CTRL1_IE_SHIFT)
-#define MICFIL_VAD0_CTRL1_IE		BIT(MICFIL_VAD0_CTRL1_IE_SHIFT)
-#define MICFIL_VAD0_CTRL1_RST_SHIFT	1
-#define MICFIL_VAD0_CTRL1_RST_MASK	BIT(MICFIL_VAD0_CTRL1_RST_SHIFT)
-#define MICFIL_VAD0_CTRL1_RST		BIT(MICFIL_VAD0_CTRL1_RST_SHIFT)
-#define MICFIL_VAD0_CTRL1_EN_SHIFT	0
-#define MICFIL_VAD0_CTRL1_EN_MASK	BIT(MICFIL_VAD0_CTRL1_EN_SHIFT)
-#define MICFIL_VAD0_CTRL1_EN		BIT(MICFIL_VAD0_CTRL1_EN_SHIFT)
+#define MICFIL_VAD0_CTRL1_CHSEL		GENMASK(26, 24)
+#define MICFIL_VAD0_CTRL1_CICOSR	GENMASK(19, 16)
+#define MICFIL_VAD0_CTRL1_INITT		GENMASK(12, 8)
+#define MICFIL_VAD0_CTRL1_ST10		BIT(4)
+#define MICFIL_VAD0_CTRL1_ERIE		BIT(3)
+#define MICFIL_VAD0_CTRL1_IE		BIT(2)
+#define MICFIL_VAD0_CTRL1_RST		BIT(1)
+#define MICFIL_VAD0_CTRL1_EN		BIT(0)
 
 /* MICFIL HWVAD0 Control 2 Register -- REG_MICFIL_VAD0_CTRL2*/
-#define MICFIL_VAD0_CTRL2_FRENDIS_SHIFT	31
-#define MICFIL_VAD0_CTRL2_FRENDIS_MASK	BIT(MICFIL_VAD0_CTRL2_FRENDIS_SHIFT)
-#define MICFIL_VAD0_CTRL2_FRENDIS	BIT(MICFIL_VAD0_CTRL2_FRENDIS_SHIFT)
-#define MICFIL_VAD0_CTRL2_PREFEN_SHIFT	30
-#define MICFIL_VAD0_CTRL2_PREFEN_MASK	BIT(MICFIL_VAD0_CTRL2_PREFEN_SHIFT)
-#define MICFIL_VAD0_CTRL2_PREFEN	BIT(MICFIL_VAD0_CTRL2_PREFEN_SHIFT)
-#define MICFIL_VAD0_CTRL2_FOUTDIS_SHIFT	28
-#define MICFIL_VAD0_CTRL2_FOUTDIS_MASK	BIT(MICFIL_VAD0_CTRL2_FOUTDIS_SHIFT)
-#define MICFIL_VAD0_CTRL2_FOUTDIS	BIT(MICFIL_VAD0_CTRL2_FOUTDIS_SHIFT)
-#define MICFIL_VAD0_CTRL2_FRAMET_SHIFT	16
-#define MICFIL_VAD0_CTRL2_FRAMET_WIDTH	6
-#define MICFIL_VAD0_CTRL2_FRAMET_MASK	((BIT(MICFIL_VAD0_CTRL2_FRAMET_WIDTH) - 1) \
-					 << MICFIL_VAD0_CTRL2_FRAMET_SHIFT)
-#define MICFIL_VAD0_CTRL2_FRAMET(v)	(((v) << MICFIL_VAD0_CTRL2_FRAMET_SHIFT) \
-					 & MICFIL_VAD0_CTRL2_FRAMET_MASK)
-#define MICFIL_VAD0_CTRL2_INPGAIN_SHIFT	8
-#define MICFIL_VAD0_CTRL2_INPGAIN_WIDTH	4
-#define MICFIL_VAD0_CTRL2_INPGAIN_MASK	((BIT(MICFIL_VAD0_CTRL2_INPGAIN_WIDTH) - 1) \
-					 << MICFIL_VAD0_CTRL2_INPGAIN_SHIFT)
-#define MICFIL_VAD0_CTRL2_INPGAIN(v)	(((v) << MICFIL_VAD0_CTRL2_INPGAIN_SHIFT) \
-					& MICFIL_VAD0_CTRL2_INPGAIN_MASK)
-#define MICFIL_VAD0_CTRL2_HPF_SHIFT	0
-#define MICFIL_VAD0_CTRL2_HPF_WIDTH	2
-#define MICFIL_VAD0_CTRL2_HPF_MASK	((BIT(MICFIL_VAD0_CTRL2_HPF_WIDTH) - 1) \
-					 << MICFIL_VAD0_CTRL2_HPF_SHIFT)
-#define MICFIL_VAD0_CTRL2_HPF(v)	(((v) << MICFIL_VAD0_CTRL2_HPF_SHIFT) \
-					 & MICFIL_VAD0_CTRL2_HPF_MASK)
+#define MICFIL_VAD0_CTRL2_FRENDIS	BIT(31)
+#define MICFIL_VAD0_CTRL2_PREFEN	BIT(30)
+#define MICFIL_VAD0_CTRL2_FOUTDIS	BIT(28)
+#define MICFIL_VAD0_CTRL2_FRAMET	GENMASK(21, 16)
+#define MICFIL_VAD0_CTRL2_INPGAIN	GENMASK(11, 8)
+#define MICFIL_VAD0_CTRL2_HPF		GENMASK(1, 0)
 
 /* MICFIL HWVAD0 Signal CONFIG Register -- REG_MICFIL_VAD0_SCONFIG */
-#define MICFIL_VAD0_SCONFIG_SFILEN_SHIFT	31
-#define MICFIL_VAD0_SCONFIG_SFILEN_MASK		BIT(MICFIL_VAD0_SCONFIG_SFILEN_SHIFT)
-#define MICFIL_VAD0_SCONFIG_SFILEN		BIT(MICFIL_VAD0_SCONFIG_SFILEN_SHIFT)
-#define MICFIL_VAD0_SCONFIG_SMAXEN_SHIFT	30
-#define MICFIL_VAD0_SCONFIG_SMAXEN_MASK		BIT(MICFIL_VAD0_SCONFIG_SMAXEN_SHIFT)
-#define MICFIL_VAD0_SCONFIG_SMAXEN		BIT(MICFIL_VAD0_SCONFIG_SMAXEN_SHIFT)
-#define MICFIL_VAD0_SCONFIG_SGAIN_SHIFT		0
-#define MICFIL_VAD0_SCONFIG_SGAIN_WIDTH		4
-#define MICFIL_VAD0_SCONFIG_SGAIN_MASK		((BIT(MICFIL_VAD0_SCONFIG_SGAIN_WIDTH) - 1) \
-						<< MICFIL_VAD0_SCONFIG_SGAIN_SHIFT)
-#define MICFIL_VAD0_SCONFIG_SGAIN(v)		(((v) << MICFIL_VAD0_SCONFIG_SGAIN_SHIFT) \
-						 & MICFIL_VAD0_SCONFIG_SGAIN_MASK)
+#define MICFIL_VAD0_SCONFIG_SFILEN		BIT(31)
+#define MICFIL_VAD0_SCONFIG_SMAXEN		BIT(30)
+#define MICFIL_VAD0_SCONFIG_SGAIN		GENMASK(3, 0)
 
 /* MICFIL HWVAD0 Noise CONFIG Register -- REG_MICFIL_VAD0_NCONFIG */
-#define MICFIL_VAD0_NCONFIG_NFILAUT_SHIFT	31
-#define MICFIL_VAD0_NCONFIG_NFILAUT_MASK	BIT(MICFIL_VAD0_NCONFIG_NFILAUT_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NFILAUT		BIT(MICFIL_VAD0_NCONFIG_NFILAUT_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NMINEN_SHIFT	30
-#define MICFIL_VAD0_NCONFIG_NMINEN_MASK		BIT(MICFIL_VAD0_NCONFIG_NMINEN_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NMINEN		BIT(MICFIL_VAD0_NCONFIG_NMINEN_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NDECEN_SHIFT	29
-#define MICFIL_VAD0_NCONFIG_NDECEN_MASK		BIT(MICFIL_VAD0_NCONFIG_NDECEN_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NDECEN		BIT(MICFIL_VAD0_NCONFIG_NDECEN_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NOREN_SHIFT		28
-#define MICFIL_VAD0_NCONFIG_NOREN		BIT(MICFIL_VAD0_NCONFIG_NOREN_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NFILADJ_SHIFT	8
-#define MICFIL_VAD0_NCONFIG_NFILADJ_WIDTH	5
-#define MICFIL_VAD0_NCONFIG_NFILADJ_MASK	((BIT(MICFIL_VAD0_NCONFIG_NFILADJ_WIDTH) - 1) \
-						 << MICFIL_VAD0_NCONFIG_NFILADJ_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NFILADJ(v)		(((v) << MICFIL_VAD0_NCONFIG_NFILADJ_SHIFT) \
-						 & MICFIL_VAD0_NCONFIG_NFILADJ_MASK)
-#define MICFIL_VAD0_NCONFIG_NGAIN_SHIFT		0
-#define MICFIL_VAD0_NCONFIG_NGAIN_WIDTH		4
-#define MICFIL_VAD0_NCONFIG_NGAIN_MASK		((BIT(MICFIL_VAD0_NCONFIG_NGAIN_WIDTH) - 1) \
-						 << MICFIL_VAD0_NCONFIG_NGAIN_SHIFT)
-#define MICFIL_VAD0_NCONFIG_NGAIN(v)		(((v) << MICFIL_VAD0_NCONFIG_NGAIN_SHIFT) \
-						 & MICFIL_VAD0_NCONFIG_NGAIN_MASK)
+#define MICFIL_VAD0_NCONFIG_NFILAUT		BIT(31)
+#define MICFIL_VAD0_NCONFIG_NMINEN		BIT(30)
+#define MICFIL_VAD0_NCONFIG_NDECEN		BIT(29)
+#define MICFIL_VAD0_NCONFIG_NOREN		BIT(28)
+#define MICFIL_VAD0_NCONFIG_NFILADJ		GENMASK(12, 8)
+#define MICFIL_VAD0_NCONFIG_NGAIN		GENMASK(3, 0)
 
 /* MICFIL HWVAD0 Zero-Crossing Detector - REG_MICFIL_VAD0_ZCD */
-#define MICFIL_VAD0_ZCD_ZCDTH_SHIFT	16
-#define MICFIL_VAD0_ZCD_ZCDTH_WIDTH	10
-#define MICFIL_VAD0_ZCD_ZCDTH_MASK	((BIT(MICFIL_VAD0_ZCD_ZCDTH_WIDTH) - 1) \
-					 << MICFIL_VAD0_ZCD_ZCDTH_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDTH(v)	(((v) << MICFIL_VAD0_ZCD_ZCDTH_SHIFT)\
-					 & MICFIL_VAD0_ZCD_ZCDTH_MASK)
-#define MICFIL_VAD0_ZCD_ZCDADJ_SHIFT	8
-#define MICFIL_VAD0_ZCD_ZCDADJ_WIDTH	4
-#define MICFIL_VAD0_ZCD_ZCDADJ_MASK	((BIT(MICFIL_VAD0_ZCD_ZCDADJ_WIDTH) - 1)\
-					 << MICFIL_VAD0_ZCD_ZCDADJ_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDADJ(v)	(((v) << MICFIL_VAD0_ZCD_ZCDADJ_SHIFT)\
-					 & MICFIL_VAD0_ZCD_ZCDADJ_MASK)
-#define MICFIL_VAD0_ZCD_ZCDAND_SHIFT	4
-#define MICFIL_VAD0_ZCD_ZCDAND_MASK	BIT(MICFIL_VAD0_ZCD_ZCDAND_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDAND		BIT(MICFIL_VAD0_ZCD_ZCDAND_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDAUT_SHIFT	2
-#define MICFIL_VAD0_ZCD_ZCDAUT_MASK	BIT(MICFIL_VAD0_ZCD_ZCDAUT_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDAUT		BIT(MICFIL_VAD0_ZCD_ZCDAUT_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDEN_SHIFT	0
-#define MICFIL_VAD0_ZCD_ZCDEN_MASK	BIT(MICFIL_VAD0_ZCD_ZCDEN_SHIFT)
-#define MICFIL_VAD0_ZCD_ZCDEN		BIT(MICFIL_VAD0_ZCD_ZCDEN_SHIFT)
+#define MICFIL_VAD0_ZCD_ZCDTH		GENMASK(25, 16)
+#define MICFIL_VAD0_ZCD_ZCDADJ		GENMASK(11, 8)
+#define MICFIL_VAD0_ZCD_ZCDAND		BIT(4)
+#define MICFIL_VAD0_ZCD_ZCDAUT		BIT(2)
+#define MICFIL_VAD0_ZCD_ZCDEN		BIT(0)
 
 /* MICFIL HWVAD0 Status Register - REG_MICFIL_VAD0_STAT */
-#define MICFIL_VAD0_STAT_INITF_SHIFT	31
-#define MICFIL_VAD0_STAT_INITF_MASK	BIT(MICFIL_VAD0_STAT_INITF_SHIFT)
-#define MICFIL_VAD0_STAT_INITF		BIT(MICFIL_VAD0_STAT_INITF_SHIFT)
-#define MICFIL_VAD0_STAT_INSATF_SHIFT	16
-#define MICFIL_VAD0_STAT_INSATF_MASK	BIT(MICFIL_VAD0_STAT_INSATF_SHIFT)
-#define MICFIL_VAD0_STAT_INSATF		BIT(MICFIL_VAD0_STAT_INSATF_SHIFT)
-#define MICFIL_VAD0_STAT_EF_SHIFT	15
-#define MICFIL_VAD0_STAT_EF_MASK	BIT(MICFIL_VAD0_STAT_EF_SHIFT)
-#define MICFIL_VAD0_STAT_EF		BIT(MICFIL_VAD0_STAT_EF_SHIFT)
-#define MICFIL_VAD0_STAT_IF_SHIFT	0
-#define MICFIL_VAD0_STAT_IF_MASK	BIT(MICFIL_VAD0_STAT_IF_SHIFT)
-#define MICFIL_VAD0_STAT_IF		BIT(MICFIL_VAD0_STAT_IF_SHIFT)
+#define MICFIL_VAD0_STAT_INITF		BIT(31)
+#define MICFIL_VAD0_STAT_INSATF		BIT(16)
+#define MICFIL_VAD0_STAT_EF		BIT(15)
+#define MICFIL_VAD0_STAT_IF		BIT(0)
 
 /* MICFIL Output Control Register */
 #define MICFIL_OUTGAIN_CHX_SHIFT(v)	(4 * (v))
 
 /* Constants */
-#define MICFIL_DMA_IRQ_DISABLED(v)	((v) & MICFIL_CTRL1_DISEL_MASK)
-#define MICFIL_DMA_ENABLED(v)		((0x1 << MICFIL_CTRL1_DISEL_SHIFT) \
-					 == ((v) & MICFIL_CTRL1_DISEL_MASK))
-#define MICFIL_IRQ_ENABLED(v)		((0x2 << MICFIL_CTRL1_DISEL_SHIFT) \
-					 == ((v) & MICFIL_CTRL1_DISEL_MASK))
 #define MICFIL_OUTPUT_CHANNELS		8
 #define MICFIL_FIFO_NUM			8
 
@@ -278,6 +133,5 @@
 #define MICFIL_SLEEP_MIN		90000 /* in us */
 #define MICFIL_SLEEP_MAX		100000 /* in us */
 #define MICFIL_DMA_MAXBURST_RX		6
-#define MICFIL_CTRL2_OSR_DEFAULT	(0 << MICFIL_CTRL2_CICOSR_SHIFT)
 
 #endif /* _FSL_MICFIL_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_mqs.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_mqs.c
@@ -204,10 +204,10 @@
 		}
 
 		mqs_priv->regmap = syscon_node_to_regmap(gpr_np);
+		of_node_put(gpr_np);
 		if (IS_ERR(mqs_priv->regmap)) {
 			dev_err(&pdev->dev, "failed to get gpr regmap\n");
-			ret = PTR_ERR(mqs_priv->regmap);
-			goto err_free_gpr_np;
+			return PTR_ERR(mqs_priv->regmap);
 		}
 	} else {
 		regs = devm_platform_ioremap_resource(pdev, 0);
@@ -236,8 +236,7 @@
 	if (IS_ERR(mqs_priv->mclk)) {
 		dev_err(&pdev->dev, "failed to get the clock: %ld\n",
 			PTR_ERR(mqs_priv->mclk));
-		ret = PTR_ERR(mqs_priv->mclk);
-		goto err_free_gpr_np;
+		return PTR_ERR(mqs_priv->mclk);
 	}
 
 	dev_set_drvdata(&pdev->dev, mqs_priv);
@@ -246,13 +245,9 @@
 	ret = devm_snd_soc_register_component(&pdev->dev, &soc_codec_fsl_mqs,
 			&fsl_mqs_dai, 1);
 	if (ret)
-		goto err_free_gpr_np;
-	return 0;
-
-err_free_gpr_np:
-	of_node_put(gpr_np);
+		return ret;
 
-	return ret;
+	return 0;
 }
 
 static int fsl_mqs_remove(struct platform_device *pdev)
@@ -337,4 +332,4 @@
 MODULE_AUTHOR("Shengjiu Wang <Shengjiu.Wang@nxp.com>");
 MODULE_DESCRIPTION("MQS codec driver");
 MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform: fsl-mqs");
+MODULE_ALIAS("platform:fsl-mqs");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_rpmsg.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_rpmsg.c
@@ -191,7 +191,7 @@
 	ret = devm_snd_soc_register_component(&pdev->dev, &fsl_component,
 					      &fsl_rpmsg_dai, 1);
 	if (ret)
-		return ret;
+		goto err_pm_disable;
 
 	rpmsg->card_pdev = platform_device_register_data(&pdev->dev,
 							 "imx-audio-rpmsg",
@@ -201,16 +201,22 @@
 	if (IS_ERR(rpmsg->card_pdev)) {
 		dev_err(&pdev->dev, "failed to register rpmsg card\n");
 		ret = PTR_ERR(rpmsg->card_pdev);
-		return ret;
+		goto err_pm_disable;
 	}
 
 	return 0;
+
+err_pm_disable:
+	pm_runtime_disable(&pdev->dev);
+	return ret;
 }
 
 static int fsl_rpmsg_remove(struct platform_device *pdev)
 {
 	struct fsl_rpmsg *rpmsg = platform_get_drvdata(pdev);
 
+	pm_runtime_disable(&pdev->dev);
+
 	if (rpmsg->card_pdev)
 		platform_device_unregister(rpmsg->card_pdev);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_sai.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_sai.c
@@ -231,6 +231,7 @@
 	if (!sai->is_lsb_first)
 		val_cr4 |= FSL_SAI_CR4_MF;
 
+	sai->is_dsp_mode = false;
 	/* DAI mode */
 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
 	case SND_SOC_DAIFMT_I2S:
@@ -297,23 +298,23 @@
 		return -EINVAL;
 	}
 
-	/* DAI clock master masks */
-	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
-	case SND_SOC_DAIFMT_CBS_CFS:
+	/* DAI clock provider masks */
+	switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
+	case SND_SOC_DAIFMT_CBC_CFC:
 		val_cr2 |= FSL_SAI_CR2_BCD_MSTR;
 		val_cr4 |= FSL_SAI_CR4_FSD_MSTR;
-		sai->is_slave_mode = false;
+		sai->is_consumer_mode = false;
 		break;
-	case SND_SOC_DAIFMT_CBM_CFM:
-		sai->is_slave_mode = true;
+	case SND_SOC_DAIFMT_CBP_CFP:
+		sai->is_consumer_mode = true;
 		break;
-	case SND_SOC_DAIFMT_CBS_CFM:
+	case SND_SOC_DAIFMT_CBC_CFP:
 		val_cr2 |= FSL_SAI_CR2_BCD_MSTR;
-		sai->is_slave_mode = false;
+		sai->is_consumer_mode = false;
 		break;
-	case SND_SOC_DAIFMT_CBM_CFS:
+	case SND_SOC_DAIFMT_CBP_CFC:
 		val_cr4 |= FSL_SAI_CR4_FSD_MSTR;
-		sai->is_slave_mode = true;
+		sai->is_consumer_mode = true;
 		break;
 	default:
 		return -EINVAL;
@@ -356,8 +357,8 @@
 	u32 id;
 	int ret = 0;
 
-	/* Don't apply to slave mode */
-	if (sai->is_slave_mode)
+	/* Don't apply to consumer mode */
+	if (sai->is_consumer_mode)
 		return 0;
 
 	/*
@@ -462,7 +463,7 @@
 
 	pins = DIV_ROUND_UP(channels, slots);
 
-	if (!sai->is_slave_mode) {
+	if (!sai->is_consumer_mode) {
 		if (sai->bclk_ratio)
 			ret = fsl_sai_set_bclk(cpu_dai, tx,
 					       sai->bclk_ratio *
@@ -497,17 +498,20 @@
 
 	val_cr4 |= FSL_SAI_CR4_FRSZ(slots);
 
+	/* Set to avoid channel swap */
+	val_cr4 |= FSL_SAI_CR4_FCONT;
+
 	/* Set to output mode to avoid tri-stated data pins */
 	if (tx)
 		val_cr4 |= FSL_SAI_CR4_CHMOD;
 
 	/*
-	 * For SAI master mode, when Tx(Rx) sync with Rx(Tx) clock, Rx(Tx) will
+	 * For SAI provider mode, when Tx(Rx) sync with Rx(Tx) clock, Rx(Tx) will
 	 * generate bclk and frame clock for Tx(Rx), we should set RCR4(TCR4),
 	 * RCR5(TCR5) for playback(capture), or there will be sync error.
 	 */
 
-	if (!sai->is_slave_mode && fsl_sai_dir_is_synced(sai, adir)) {
+	if (!sai->is_consumer_mode && fsl_sai_dir_is_synced(sai, adir)) {
 		regmap_update_bits(sai->regmap, FSL_SAI_xCR4(!tx, ofs),
 				   FSL_SAI_CR4_SYWD_MASK | FSL_SAI_CR4_FRSZ_MASK |
 				   FSL_SAI_CR4_CHMOD_MASK,
@@ -522,7 +526,7 @@
 			   FSL_SAI_CR3_TRCE((1 << pins) - 1));
 	regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs),
 			   FSL_SAI_CR4_SYWD_MASK | FSL_SAI_CR4_FRSZ_MASK |
-			   FSL_SAI_CR4_CHMOD_MASK,
+			   FSL_SAI_CR4_CHMOD_MASK | FSL_SAI_CR4_FCONT_MASK,
 			   val_cr4);
 	regmap_update_bits(sai->regmap, FSL_SAI_xCR5(tx, ofs),
 			   FSL_SAI_CR5_WNW_MASK | FSL_SAI_CR5_W0W_MASK |
@@ -543,7 +547,7 @@
 	regmap_update_bits(sai->regmap, FSL_SAI_xCR3(tx, ofs),
 			   FSL_SAI_CR3_TRCE_MASK, 0);
 
-	if (!sai->is_slave_mode &&
+	if (!sai->is_consumer_mode &&
 			sai->mclk_streams & BIT(substream->stream)) {
 		clk_disable_unprepare(sai->mclk_clk[sai->mclk_id[tx]]);
 		sai->mclk_streams &= ~BIT(substream->stream);
@@ -559,7 +563,7 @@
 	u32 xcsr, count = 100;
 
 	regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs),
-			   FSL_SAI_CSR_TERE, 0);
+			   FSL_SAI_CSR_TERE | FSL_SAI_CSR_BCE, 0);
 
 	/* TERE will remain set till the end of current frame */
 	do {
@@ -577,7 +581,7 @@
 	 * This is a hardware bug, and will be fix in the
 	 * next sai version.
 	 */
-	if (!sai->is_slave_mode) {
+	if (!sai->is_consumer_mode) {
 		/* Software Reset */
 		regmap_write(sai->regmap, FSL_SAI_xCSR(tx, ofs), FSL_SAI_CSR_SR);
 		/* Clear SR bit to finish the reset */
@@ -1000,6 +1004,7 @@
 static int fsl_sai_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
 	struct fsl_sai *sai;
 	struct regmap *gpr;
 	struct resource *res;
@@ -1008,12 +1013,12 @@
 	int irq, ret, i;
 	int index;
 
-	sai = devm_kzalloc(&pdev->dev, sizeof(*sai), GFP_KERNEL);
+	sai = devm_kzalloc(dev, sizeof(*sai), GFP_KERNEL);
 	if (!sai)
 		return -ENOMEM;
 
 	sai->pdev = pdev;
-	sai->soc_data = of_device_get_match_data(&pdev->dev);
+	sai->soc_data = of_device_get_match_data(dev);
 
 	sai->is_lsb_first = of_property_read_bool(np, "lsb-first");
 
@@ -1028,18 +1033,18 @@
 			ARRAY_SIZE(fsl_sai_reg_defaults_ofs8);
 	}
 
-	sai->regmap = devm_regmap_init_mmio(&pdev->dev, base, &fsl_sai_regmap_config);
+	sai->regmap = devm_regmap_init_mmio(dev, base, &fsl_sai_regmap_config);
 	if (IS_ERR(sai->regmap)) {
-		dev_err(&pdev->dev, "regmap init failed\n");
+		dev_err(dev, "regmap init failed\n");
 		return PTR_ERR(sai->regmap);
 	}
 
-	sai->bus_clk = devm_clk_get(&pdev->dev, "bus");
+	sai->bus_clk = devm_clk_get(dev, "bus");
 	/* Compatible with old DTB cases */
 	if (IS_ERR(sai->bus_clk) && PTR_ERR(sai->bus_clk) != -EPROBE_DEFER)
-		sai->bus_clk = devm_clk_get(&pdev->dev, "sai");
+		sai->bus_clk = devm_clk_get(dev, "sai");
 	if (IS_ERR(sai->bus_clk)) {
-		dev_err(&pdev->dev, "failed to get bus clock: %ld\n",
+		dev_err(dev, "failed to get bus clock: %ld\n",
 				PTR_ERR(sai->bus_clk));
 		/* -EPROBE_DEFER */
 		return PTR_ERR(sai->bus_clk);
@@ -1047,9 +1052,9 @@
 
 	for (i = 1; i < FSL_SAI_MCLK_MAX; i++) {
 		sprintf(tmp, "mclk%d", i);
-		sai->mclk_clk[i] = devm_clk_get(&pdev->dev, tmp);
+		sai->mclk_clk[i] = devm_clk_get(dev, tmp);
 		if (IS_ERR(sai->mclk_clk[i])) {
-			dev_err(&pdev->dev, "failed to get mclk%d clock: %ld\n",
+			dev_err(dev, "failed to get mclk%d clock: %ld\n",
 					i + 1, PTR_ERR(sai->mclk_clk[i]));
 			sai->mclk_clk[i] = NULL;
 		}
@@ -1064,10 +1069,10 @@
 	if (irq < 0)
 		return irq;
 
-	ret = devm_request_irq(&pdev->dev, irq, fsl_sai_isr, IRQF_SHARED,
+	ret = devm_request_irq(dev, irq, fsl_sai_isr, IRQF_SHARED,
 			       np->name, sai);
 	if (ret) {
-		dev_err(&pdev->dev, "failed to claim irq %u\n", irq);
+		dev_err(dev, "failed to claim irq %u\n", irq);
 		return ret;
 	}
 
@@ -1084,7 +1089,7 @@
 	if (of_find_property(np, "fsl,sai-synchronous-rx", NULL) &&
 	    of_find_property(np, "fsl,sai-asynchronous", NULL)) {
 		/* error out if both synchronous and asynchronous are present */
-		dev_err(&pdev->dev, "invalid binding for synchronous mode\n");
+		dev_err(dev, "invalid binding for synchronous mode\n");
 		return -EINVAL;
 	}
 
@@ -1105,7 +1110,7 @@
 	    of_device_is_compatible(np, "fsl,imx6ul-sai")) {
 		gpr = syscon_regmap_lookup_by_compatible("fsl,imx6ul-iomuxc-gpr");
 		if (IS_ERR(gpr)) {
-			dev_err(&pdev->dev, "cannot find iomuxc registers\n");
+			dev_err(dev, "cannot find iomuxc registers\n");
 			return PTR_ERR(gpr);
 		}
 
@@ -1123,23 +1128,23 @@
 	sai->dma_params_tx.maxburst = FSL_SAI_MAXBURST_TX;
 
 	platform_set_drvdata(pdev, sai);
-	pm_runtime_enable(&pdev->dev);
-	if (!pm_runtime_enabled(&pdev->dev)) {
-		ret = fsl_sai_runtime_resume(&pdev->dev);
+	pm_runtime_enable(dev);
+	if (!pm_runtime_enabled(dev)) {
+		ret = fsl_sai_runtime_resume(dev);
 		if (ret)
 			goto err_pm_disable;
 	}
 
-	ret = pm_runtime_get_sync(&pdev->dev);
+	ret = pm_runtime_get_sync(dev);
 	if (ret < 0) {
-		pm_runtime_put_noidle(&pdev->dev);
+		pm_runtime_put_noidle(dev);
 		goto err_pm_get_sync;
 	}
 
 	/* Get sai version */
-	ret = fsl_sai_check_version(&pdev->dev);
+	ret = fsl_sai_check_version(dev);
 	if (ret < 0)
-		dev_warn(&pdev->dev, "Error reading SAI version: %d\n", ret);
+		dev_warn(dev, "Error reading SAI version: %d\n", ret);
 
 	/* Select MCLK direction */
 	if (of_find_property(np, "fsl,sai-mclk-direction-output", NULL) &&
@@ -1148,8 +1153,8 @@
 				   FSL_SAI_MCTL_MCLK_EN, FSL_SAI_MCTL_MCLK_EN);
 	}
 
-	ret = pm_runtime_put_sync(&pdev->dev);
-	if (ret < 0)
+	ret = pm_runtime_put_sync(dev);
+	if (ret < 0 && ret != -ENOSYS)
 		goto err_pm_get_sync;
 
 	/*
@@ -1161,12 +1166,12 @@
 		if (ret)
 			goto err_pm_get_sync;
 	} else {
-		ret = devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0);
+		ret = devm_snd_dmaengine_pcm_register(dev, NULL, 0);
 		if (ret)
 			goto err_pm_get_sync;
 	}
 
-	ret = devm_snd_soc_register_component(&pdev->dev, &fsl_component,
+	ret = devm_snd_soc_register_component(dev, &fsl_component,
 					      &sai->cpu_dai_drv, 1);
 	if (ret)
 		goto err_pm_get_sync;
@@ -1174,10 +1179,10 @@
 	return ret;
 
 err_pm_get_sync:
-	if (!pm_runtime_status_suspended(&pdev->dev))
-		fsl_sai_runtime_suspend(&pdev->dev);
+	if (!pm_runtime_status_suspended(dev))
+		fsl_sai_runtime_suspend(dev);
 err_pm_disable:
-	pm_runtime_disable(&pdev->dev);
+	pm_runtime_disable(dev);
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_sai.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_sai.h
@@ -80,13 +80,14 @@
 #define FSL_SAI_xCR3(tx, ofs)	(tx ? FSL_SAI_TCR3(ofs) : FSL_SAI_RCR3(ofs))
 #define FSL_SAI_xCR4(tx, ofs)	(tx ? FSL_SAI_TCR4(ofs) : FSL_SAI_RCR4(ofs))
 #define FSL_SAI_xCR5(tx, ofs)	(tx ? FSL_SAI_TCR5(ofs) : FSL_SAI_RCR5(ofs))
-#define FSL_SAI_xDR(tx, ofs)	(tx ? FSL_SAI_TDR(ofs) : FSL_SAI_RDR(ofs))
-#define FSL_SAI_xFR(tx, ofs)	(tx ? FSL_SAI_TFR(ofs) : FSL_SAI_RFR(ofs))
+#define FSL_SAI_xDR0(tx)	(tx ? FSL_SAI_TDR0 : FSL_SAI_RDR0)
+#define FSL_SAI_xFR0(tx)	(tx ? FSL_SAI_TFR0 : FSL_SAI_RFR0)
 #define FSL_SAI_xMR(tx)		(tx ? FSL_SAI_TMR : FSL_SAI_RMR)
 
 /* SAI Transmit/Receive Control Register */
 #define FSL_SAI_CSR_TERE	BIT(31)
 #define FSL_SAI_CSR_SE		BIT(30)
+#define FSL_SAI_CSR_BCE		BIT(28)
 #define FSL_SAI_CSR_FR		BIT(25)
 #define FSL_SAI_CSR_SR		BIT(24)
 #define FSL_SAI_CSR_xF_SHIFT	16
@@ -131,6 +132,7 @@
 
 /* SAI Transmit and Receive Configuration 4 Register */
 
+#define FSL_SAI_CR4_FCONT_MASK	BIT(28)
 #define FSL_SAI_CR4_FCONT	BIT(28)
 #define FSL_SAI_CR4_FCOMB_SHIFT BIT(26)
 #define FSL_SAI_CR4_FCOMB_SOFT  BIT(27)
@@ -259,7 +261,7 @@
 	struct clk *bus_clk;
 	struct clk *mclk_clk[FSL_SAI_MCLK_MAX];
 
-	bool is_slave_mode;
+	bool is_consumer_mode;
 	bool is_lsb_first;
 	bool is_dsp_mode;
 	bool synchronous[2];
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_spdif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_spdif.c
@@ -598,6 +598,8 @@
 		mask = SCR_TXFIFO_AUTOSYNC_MASK | SCR_TXFIFO_CTRL_MASK |
 			SCR_TXSEL_MASK | SCR_USRC_SEL_MASK |
 			SCR_TXFIFO_FSEL_MASK;
+		/* Disable TX clock */
+		regmap_update_bits(regmap, REG_SPDIF_STC, STC_TXCLK_ALL_EN_MASK, 0);
 	} else {
 		scr = SCR_RXFIFO_OFF | SCR_RXFIFO_CTL_ZERO;
 		mask = SCR_RXFIFO_FSEL_MASK | SCR_RXFIFO_AUTOSYNC_MASK|
@@ -664,6 +666,8 @@
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
 		regmap_update_bits(regmap, REG_SPDIF_SCR, dmaen, 0);
 		regmap_update_bits(regmap, REG_SPDIF_SIE, intr, 0);
+		regmap_write(regmap, REG_SPDIF_STL, 0x0);
+		regmap_write(regmap, REG_SPDIF_STR, 0x0);
 		break;
 	default:
 		return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/fsl_ssi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/fsl_ssi.c
@@ -1160,14 +1160,14 @@
 	.symmetric_channels = 1,
 	.probe = fsl_ssi_dai_probe,
 	.playback = {
-		.stream_name = "AC97 Playback",
+		.stream_name = "CPU AC97 Playback",
 		.channels_min = 2,
 		.channels_max = 2,
 		.rates = SNDRV_PCM_RATE_8000_48000,
 		.formats = SNDRV_PCM_FMTBIT_S16 | SNDRV_PCM_FMTBIT_S20,
 	},
 	.capture = {
-		.stream_name = "AC97 Capture",
+		.stream_name = "CPU AC97 Capture",
 		.channels_min = 2,
 		.channels_max = 2,
 		.rates = SNDRV_PCM_RATE_48000,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-audmix.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-audmix.c
@@ -228,6 +228,8 @@
 
 		dai_name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s%s",
 					  fe_name_pref, args.np->full_name + 1);
+		if (!dai_name)
+			return -ENOMEM;
 
 		dev_info(pdev->dev.parent, "DAI FE name:%s\n", dai_name);
 
@@ -236,6 +238,8 @@
 			capture_dai_name =
 				devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s %s",
 					       dai_name, "CPU-Capture");
+			if (!capture_dai_name)
+				return -ENOMEM;
 		}
 
 		priv->dai[i].cpus = &dlc[0];
@@ -266,6 +270,8 @@
 				       "AUDMIX-Playback-%d", i);
 		be_cp = devm_kasprintf(&pdev->dev, GFP_KERNEL,
 				       "AUDMIX-Capture-%d", i);
+		if (!be_name || !be_pb || !be_cp)
+			return -ENOMEM;
 
 		priv->dai[num_dai + i].cpus = &dlc[3];
 		priv->dai[num_dai + i].codecs = &dlc[4];
@@ -293,6 +299,9 @@
 		priv->dapm_routes[i].source =
 			devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s %s",
 				       dai_name, "CPU-Playback");
+		if (!priv->dapm_routes[i].source)
+			return -ENOMEM;
+
 		priv->dapm_routes[i].sink = be_pb;
 		priv->dapm_routes[num_dai + i].source   = be_pb;
 		priv->dapm_routes[num_dai + i].sink     = be_cp;
@@ -311,7 +320,7 @@
 	if (IS_ERR(priv->cpu_mclk)) {
 		ret = PTR_ERR(priv->cpu_mclk);
 		dev_err(&cpu_pdev->dev, "failed to get DAI mclk1: %d\n", ret);
-		return -EINVAL;
+		return ret;
 	}
 
 	priv->audmix_pdev = audmix_pdev;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-audmux.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-audmux.c
@@ -298,7 +298,7 @@
 		audmux_clk = NULL;
 	}
 
-	audmux_type = (enum imx_audmux_type)of_device_get_match_data(&pdev->dev);
+	audmux_type = (uintptr_t)of_device_get_match_data(&pdev->dev);
 
 	switch (audmux_type) {
 	case IMX31_AUDMUX:
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-card.c
@@ -17,6 +17,9 @@
 
 #include "fsl_sai.h"
 
+#define IMX_CARD_MCLK_22P5792MHZ  22579200
+#define IMX_CARD_MCLK_24P576MHZ   24576000
+
 enum codec_type {
 	CODEC_DUMMY = 0,
 	CODEC_AK5558 = 1,
@@ -115,12 +118,12 @@
 	struct snd_soc_card card;
 	int num_dapm_routes;
 	u32 asrc_rate;
-	u32 asrc_format;
+	snd_pcm_format_t asrc_format;
 };
 
 static struct imx_akcodec_fs_mul ak4458_fs_mul[] = {
 	/* Normal, < 32kHz */
-	{ .rmin = 8000,   .rmax = 24000,  .wmin = 1024, .wmax = 1024, },
+	{ .rmin = 8000,   .rmax = 24000,  .wmin = 256,  .wmax = 1024, },
 	/* Normal, 32kHz */
 	{ .rmin = 32000,  .rmax = 32000,  .wmin = 256,  .wmax = 1024, },
 	/* Normal */
@@ -151,8 +154,8 @@
 	 * Table 7      - mapping multiplier and speed mode
 	 * Tables 8 & 9 - mapping speed mode and LRCK fs
 	 */
-	{ .rmin = 8000,   .rmax = 32000,  .wmin = 1024, .wmax = 1024, }, /* Normal, <= 32kHz */
-	{ .rmin = 44100,  .rmax = 48000,  .wmin = 512,  .wmax = 512, }, /* Normal */
+	{ .rmin = 8000,   .rmax = 32000,  .wmin = 256,  .wmax = 1024, }, /* Normal, <= 32kHz */
+	{ .rmin = 44100,  .rmax = 48000,  .wmin = 256,  .wmax = 512, }, /* Normal */
 	{ .rmin = 88200,  .rmax = 96000,  .wmin = 256,  .wmax = 256, }, /* Double */
 	{ .rmin = 176400, .rmax = 192000, .wmin = 128,  .wmax = 128, }, /* Quad */
 	{ .rmin = 352800, .rmax = 384000, .wmin = 128,  .wmax = 128, }, /* Oct */
@@ -164,7 +167,7 @@
  * (Table 4 from datasheet)
  */
 static struct imx_akcodec_fs_mul ak5558_fs_mul[] = {
-	{ .rmin = 8000,   .rmax = 32000,  .wmin = 1024, .wmax = 1024, },
+	{ .rmin = 8000,   .rmax = 32000,  .wmin = 512,  .wmax = 1024, },
 	{ .rmin = 44100,  .rmax = 48000,  .wmin = 512,  .wmax = 512, },
 	{ .rmin = 88200,  .rmax = 96000,  .wmin = 256,  .wmax = 256, },
 	{ .rmin = 176400, .rmax = 192000, .wmin = 128,  .wmax = 128, },
@@ -247,13 +250,14 @@
 }
 
 static unsigned long akcodec_get_mclk_rate(struct snd_pcm_substream *substream,
-					   struct snd_pcm_hw_params *params)
+					   struct snd_pcm_hw_params *params,
+					   int slots, int slot_width)
 {
 	struct snd_soc_pcm_runtime *rtd = substream->private_data;
 	struct imx_card_data *data = snd_soc_card_get_drvdata(rtd->card);
 	const struct imx_card_plat_data *plat_data = data->plat_data;
 	struct dai_link_data *link_data = &data->link_data[rtd->num];
-	unsigned int width = link_data->slots * link_data->slot_width;
+	unsigned int width = slots * slot_width;
 	unsigned int rate = params_rate(params);
 	int i;
 
@@ -349,12 +353,17 @@
 
 	/* Set MCLK freq */
 	if (codec_is_akcodec(plat_data->type))
-		mclk_freq = akcodec_get_mclk_rate(substream, params);
+		mclk_freq = akcodec_get_mclk_rate(substream, params, slots, slot_width);
 	else
 		mclk_freq = params_rate(params) * slots * slot_width;
-	/* Use the maximum freq from DSD512 (512*44100 = 22579200) */
-	if (format_is_dsd(params))
-		mclk_freq = 22579200;
+
+	if (format_is_dsd(params)) {
+		/* Use the maximum freq from DSD512 (512*44100 = 22579200) */
+		if (!(params_rate(params) % 11025))
+			mclk_freq = IMX_CARD_MCLK_22P5792MHZ;
+		else
+			mclk_freq = IMX_CARD_MCLK_24P576MHZ;
+	}
 
 	ret = snd_soc_dai_set_sysclk(cpu_dai, link_data->cpu_sysclk_id, mclk_freq,
 				     SND_SOC_CLOCK_OUT);
@@ -465,7 +474,7 @@
 
 	mask = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT);
 	snd_mask_none(mask);
-	snd_mask_set(mask, data->asrc_format);
+	snd_mask_set(mask, (__force unsigned int)data->asrc_format);
 
 	return 0;
 }
@@ -484,6 +493,7 @@
 	struct dai_link_data *link_data;
 	struct of_phandle_args args;
 	int ret, num_links;
+	u32 asrc_fmt = 0;
 	u32 width;
 
 	ret = snd_soc_of_parse_card_name(card, "model");
@@ -553,8 +563,23 @@
 			link_data->cpu_sysclk_id = FSL_SAI_CLK_MAST1;
 
 			/* sai may support mclk/bclk = 1 */
-			if (of_find_property(np, "fsl,mclk-equal-bclk", NULL))
+			if (of_find_property(np, "fsl,mclk-equal-bclk", NULL)) {
 				link_data->one2one_ratio = true;
+			} else {
+				int i;
+
+				/*
+				 * i.MX8MQ don't support one2one ratio, then
+				 * with ak4497 only 16bit case is supported.
+				 */
+				for (i = 0; i < ARRAY_SIZE(ak4497_fs_mul); i++) {
+					if (ak4497_fs_mul[i].rmin == 705600 &&
+					    ak4497_fs_mul[i].rmax == 768000) {
+						ak4497_fs_mul[i].wmin = 32;
+						ak4497_fs_mul[i].wmax = 32;
+					}
+				}
+			}
 		}
 
 		link->cpus->of_node = args.np;
@@ -563,9 +588,8 @@
 
 		ret = snd_soc_of_get_dai_name(cpu, &link->cpus->dai_name);
 		if (ret) {
-			if (ret != -EPROBE_DEFER)
-				dev_err(card->dev, "%s: error getting cpu dai name: %d\n",
-					link->name, ret);
+			dev_err_probe(card->dev, ret,
+				      "%s: error getting cpu dai name\n", link->name);
 			goto err;
 		}
 
@@ -573,9 +597,8 @@
 		if (codec) {
 			ret = snd_soc_of_get_dai_link_codecs(dev, codec, link);
 			if (ret < 0) {
-				if (ret != -EPROBE_DEFER)
-					dev_err(dev, "%s: codec dai not found: %d\n",
-						link->name, ret);
+				dev_err_probe(dev, ret, "%s: codec dai not found\n",
+						link->name);
 				goto err;
 			}
 
@@ -617,7 +640,8 @@
 				goto err;
 			}
 
-			ret = of_property_read_u32(args.np, "fsl,asrc-format", &data->asrc_format);
+			ret = of_property_read_u32(args.np, "fsl,asrc-format", &asrc_fmt);
+			data->asrc_format = (__force snd_pcm_format_t)asrc_fmt;
 			if (ret) {
 				/* Fallback to old binding; translate to asrc_format */
 				ret = of_property_read_u32(args.np, "fsl,asrc-width", &width);
@@ -674,6 +698,10 @@
 		of_node_put(cpu);
 		of_node_put(codec);
 		of_node_put(platform);
+
+		cpu = NULL;
+		codec = NULL;
+		platform = NULL;
 	}
 
 	return 0;
@@ -703,6 +731,7 @@
 
 	data->plat_data = plat_data;
 	data->card.dev = &pdev->dev;
+	data->card.owner = THIS_MODULE;
 
 	dev_set_drvdata(&pdev->dev, &data->card);
 	snd_soc_card_set_drvdata(&data->card, data);
@@ -730,6 +759,8 @@
 				data->dapm_routes[i].sink =
 					devm_kasprintf(&pdev->dev, GFP_KERNEL, "%d %s",
 						       i + 1, "Playback");
+				if (!data->dapm_routes[i].sink)
+					return -ENOMEM;
 				data->dapm_routes[i].source = "CPU-Playback";
 			}
 		}
@@ -747,6 +778,8 @@
 				data->dapm_routes[i].source =
 					devm_kasprintf(&pdev->dev, GFP_KERNEL, "%d %s",
 						       i + 1, "Capture");
+				if (!data->dapm_routes[i].source)
+					return -ENOMEM;
 				data->dapm_routes[i].sink = "CPU-Capture";
 			}
 		}
@@ -814,11 +847,8 @@
 	}
 
 	ret = devm_snd_soc_register_card(&pdev->dev, &data->card);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed\n");
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-es8328.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-es8328.c
@@ -87,6 +87,7 @@
 	if (int_port > MUX_PORT_MAX || int_port == 0) {
 		dev_err(dev, "mux-int-port: hardware only has %d mux ports\n",
 			MUX_PORT_MAX);
+		ret = -EINVAL;
 		goto fail;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-hdmi.c
@@ -126,6 +126,7 @@
 	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
 	if (!data) {
 		ret = -ENOMEM;
+		put_device(&cpu_pdev->dev);
 		goto fail;
 	}
 
@@ -145,6 +146,8 @@
 	data->dai.capture_only = false;
 	data->dai.init = imx_hdmi_init;
 
+	put_device(&cpu_pdev->dev);
+
 	if (of_node_name_eq(cpu_np, "sai")) {
 		data->cpu_priv.sysclk_id[1] = FSL_SAI_CLK_MAST1;
 		data->cpu_priv.sysclk_id[0] = FSL_SAI_CLK_MAST1;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-pcm-rpmsg.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-pcm-rpmsg.c
@@ -19,6 +19,7 @@
 static struct snd_pcm_hardware imx_rpmsg_pcm_hardware = {
 	.info = SNDRV_PCM_INFO_INTERLEAVED |
 		SNDRV_PCM_INFO_BLOCK_TRANSFER |
+		SNDRV_PCM_INFO_BATCH |
 		SNDRV_PCM_INFO_MMAP |
 		SNDRV_PCM_INFO_MMAP_VALID |
 		SNDRV_PCM_INFO_NO_PERIOD_WAKEUP |
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-rpmsg.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-rpmsg.c
@@ -66,6 +66,14 @@
 			    SND_SOC_DAIFMT_NB_NF |
 			    SND_SOC_DAIFMT_CBS_CFS;
 
+	/*
+	 * i.MX rpmsg sound cards work on codec slave mode. MCLK will be
+	 * disabled by CPU DAI driver in hw_free(). Some codec requires MCLK
+	 * present at power up/down sequence. So need to set ignore_pmdown_time
+	 * to power down codec immediately before MCLK is turned off.
+	 */
+	data->dai.ignore_pmdown_time = 1;
+
 	/* Optional codec node */
 	ret = of_parse_phandle_with_fixed_args(np, "audio-codec", 0, 0, &args);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-sgtl5000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-sgtl5000.c
@@ -120,19 +120,19 @@
 	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
 	if (!data) {
 		ret = -ENOMEM;
-		goto fail;
+		goto put_device;
 	}
 
 	comp = devm_kzalloc(&pdev->dev, 3 * sizeof(*comp), GFP_KERNEL);
 	if (!comp) {
 		ret = -ENOMEM;
-		goto fail;
+		goto put_device;
 	}
 
 	data->codec_clk = clk_get(&codec_dev->dev, NULL);
 	if (IS_ERR(data->codec_clk)) {
 		ret = PTR_ERR(data->codec_clk);
-		goto fail;
+		goto put_device;
 	}
 
 	data->clk_frequency = clk_get_rate(data->codec_clk);
@@ -158,10 +158,10 @@
 	data->card.dev = &pdev->dev;
 	ret = snd_soc_of_parse_card_name(&data->card, "model");
 	if (ret)
-		goto fail;
+		goto put_device;
 	ret = snd_soc_of_parse_audio_routing(&data->card, "audio-routing");
 	if (ret)
-		goto fail;
+		goto put_device;
 	data->card.num_links = 1;
 	data->card.owner = THIS_MODULE;
 	data->card.dai_link = &data->dai;
@@ -173,10 +173,8 @@
 
 	ret = devm_snd_soc_register_card(&pdev->dev, &data->card);
 	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n",
-				ret);
-		goto fail;
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed\n");
+		goto put_device;
 	}
 
 	of_node_put(ssi_np);
@@ -184,6 +182,8 @@
 
 	return 0;
 
+put_device:
+	put_device(&codec_dev->dev);
 fail:
 	if (data && !IS_ERR(data->codec_clk))
 		clk_put(data->codec_clk);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/imx-spdif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/imx-spdif.c
@@ -70,8 +70,8 @@
 		goto end;
 
 	ret = devm_snd_soc_register_card(&pdev->dev, &data->card);
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card failed: %d\n", ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed\n");
 
 end:
 	of_node_put(spdif_np);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/mpc5200_dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/mpc5200_dma.c
@@ -100,6 +100,9 @@
 
 /**
  * psc_dma_trigger: start and stop the DMA transfer.
+ * @component: triggered component
+ * @substream: triggered substream
+ * @cmd: triggered command
  *
  * This function is called by ALSA to start, stop, pause, and resume the DMA
  * transfer of data.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/fsl/pcm030-audio-fabric.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/fsl/pcm030-audio-fabric.c
@@ -93,16 +93,21 @@
 		dev_err(&op->dev, "platform_device_alloc() failed\n");
 
 	ret = platform_device_add(pdata->codec_device);
-	if (ret)
+	if (ret) {
 		dev_err(&op->dev, "platform_device_add() failed: %d\n", ret);
+		platform_device_put(pdata->codec_device);
+	}
 
 	ret = snd_soc_register_card(card);
-	if (ret)
+	if (ret) {
 		dev_err(&op->dev, "snd_soc_register_card() failed: %d\n", ret);
+		platform_device_del(pdata->codec_device);
+		platform_device_put(pdata->codec_device);
+	}
 
 	platform_set_drvdata(op, pdata);
-
 	return ret;
+
 }
 
 static int pcm030_fabric_remove(struct platform_device *op)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/generic/audio-graph-card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/generic/audio-graph-card.c
@@ -158,8 +158,10 @@
 	 *    if he unbinded CPU or Codec.
 	 */
 	ret = snd_soc_get_dai_name(&args, &dlc->dai_name);
-	if (ret < 0)
+	if (ret < 0) {
+		of_node_put(node);
 		return ret;
+	}
 
 	dlc->of_node = node;
 
@@ -481,8 +483,10 @@
 			of_node_put(codec_ep);
 			of_node_put(codec_port);
 
-			if (ret < 0)
+			if (ret < 0) {
+				of_node_put(cpu_ep);
 				return ret;
+			}
 
 			codec_port_old = codec_port;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/generic/simple-card-utils.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/generic/simple-card-utils.c
@@ -275,6 +275,7 @@
 		mclk_fs = props->mclk_fs;
 
 	if (mclk_fs) {
+		struct snd_soc_component *component;
 		mclk = params_rate(params) * mclk_fs;
 
 		for_each_prop_dai_codec(props, i, pdai) {
@@ -282,16 +283,30 @@
 			if (ret < 0)
 				return ret;
 		}
+
 		for_each_prop_dai_cpu(props, i, pdai) {
 			ret = asoc_simple_set_clk_rate(pdai, mclk);
 			if (ret < 0)
 				return ret;
 		}
+
+		/* Ensure sysclk is set on all components in case any
+		 * (such as platform components) are missed by calls to
+		 * snd_soc_dai_set_sysclk.
+		 */
+		for_each_rtd_components(rtd, i, component) {
+			ret = snd_soc_component_set_sysclk(component, 0, 0,
+							   mclk, SND_SOC_CLOCK_IN);
+			if (ret && ret != -ENOTSUPP)
+				return ret;
+		}
+
 		for_each_rtd_codec_dais(rtd, i, sdai) {
 			ret = snd_soc_dai_set_sysclk(sdai, 0, mclk, SND_SOC_CLOCK_IN);
 			if (ret && ret != -ENOTSUPP)
 				return ret;
 		}
+
 		for_each_rtd_cpu_dais(rtd, i, sdai) {
 			ret = snd_soc_dai_set_sysclk(sdai, 0, mclk, SND_SOC_CLOCK_OUT);
 			if (ret && ret != -ENOTSUPP)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/generic/simple-card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/generic/simple-card.c
@@ -28,6 +28,30 @@
 	.hw_params	= asoc_simple_hw_params,
 };
 
+static int asoc_simple_parse_platform(struct device_node *node,
+				      struct snd_soc_dai_link_component *dlc)
+{
+	struct of_phandle_args args;
+	int ret;
+
+	if (!node)
+		return 0;
+
+	/*
+	 * Get node via "sound-dai = <&phandle port>"
+	 * it will be used as xxx_of_node on soc_bind_dai_link()
+	 */
+	ret = of_parse_phandle_with_args(node, DAI, CELL, 0, &args);
+	if (ret)
+		return ret;
+
+	/* dai_name is not required and may not exist for plat component */
+
+	dlc->of_node = args.np;
+
+	return 0;
+}
+
 static int asoc_simple_parse_dai(struct device_node *node,
 				 struct snd_soc_dai_link_component *dlc,
 				 int *is_single_link)
@@ -289,7 +313,7 @@
 	if (ret < 0)
 		goto dai_link_of_err;
 
-	ret = asoc_simple_parse_dai(plat, platforms, NULL);
+	ret = asoc_simple_parse_platform(plat, platforms);
 	if (ret < 0)
 		goto dai_link_of_err;
 
@@ -393,6 +417,7 @@
 
 			if (ret < 0) {
 				of_node_put(codec);
+				of_node_put(plat);
 				of_node_put(np);
 				goto error;
 			}
@@ -655,10 +680,12 @@
 		struct snd_soc_dai_link *dai_link = priv->dai_link;
 		struct simple_dai_props *dai_props = priv->dai_props;
 
+		ret = -EINVAL;
+
 		cinfo = dev->platform_data;
 		if (!cinfo) {
 			dev_err(dev, "no info for asoc-simple-card\n");
-			return -EINVAL;
+			goto err;
 		}
 
 		if (!cinfo->name ||
@@ -667,7 +694,7 @@
 		    !cinfo->platform ||
 		    !cinfo->cpu_dai.name) {
 			dev_err(dev, "insufficient asoc_simple_card_info settings\n");
-			return -EINVAL;
+			goto err;
 		}
 
 		cpus			= dai_link->cpus;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/atom/sst/sst_acpi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/atom/sst/sst_acpi.c
@@ -126,6 +126,28 @@
 	.acpi_ipc_irq_index = 0
 };
 
+/* For "LPE0F28" ACPI device found on some Android factory OS models */
+static const struct sst_res_info lpe8086_res_info = {
+	.shim_offset = 0x140000,
+	.shim_size = 0x000100,
+	.shim_phy_addr = SST_BYT_SHIM_PHY_ADDR,
+	.ssp0_offset = 0xa0000,
+	.ssp0_size = 0x1000,
+	.dma0_offset = 0x98000,
+	.dma0_size = 0x4000,
+	.dma1_offset = 0x9c000,
+	.dma1_size = 0x4000,
+	.iram_offset = 0x0c0000,
+	.iram_size = 0x14000,
+	.dram_offset = 0x100000,
+	.dram_size = 0x28000,
+	.mbox_offset = 0x144000,
+	.mbox_size = 0x1000,
+	.acpi_lpe_res_index = 1,
+	.acpi_ddr_index = 0,
+	.acpi_ipc_irq_index = 0
+};
+
 static struct sst_platform_info byt_rvp_platform_data = {
 	.probe_data = &byt_fwparse_info,
 	.ipc_info = &byt_ipc_info,
@@ -269,10 +291,38 @@
 		mach->pdata = &chv_platform_data;
 	pdata = mach->pdata;
 
-	ret = kstrtouint(id->id, 16, &dev_id);
-	if (ret < 0) {
-		dev_err(dev, "Unique device id conversion error: %d\n", ret);
-		return ret;
+	if (!strcmp(id->id, "LPE0F28")) {
+		struct resource *rsrc;
+
+		/* Use regular BYT SST PCI VID:PID */
+		dev_id = 0x80860F28;
+		byt_rvp_platform_data.res_info = &lpe8086_res_info;
+
+		/*
+		 * The "LPE0F28" ACPI device has separate IO-mem resources for:
+		 * DDR, SHIM, MBOX, IRAM, DRAM, CFG
+		 * None of which covers the entire LPE base address range.
+		 * lpe8086_res_info.acpi_lpe_res_index points to the SHIM.
+		 * Patch this to cover the entire base address range as expected
+		 * by sst_platform_get_resources().
+		 */
+		rsrc = platform_get_resource(pdev, IORESOURCE_MEM,
+					     pdata->res_info->acpi_lpe_res_index);
+		if (!rsrc) {
+			dev_err(dev, "Invalid SHIM base\n");
+			return -EIO;
+		}
+		rsrc->start -= pdata->res_info->shim_offset;
+		rsrc->end = rsrc->start + 0x200000 - 1;
+	} else {
+		ret = kstrtouint(id->id, 16, &dev_id);
+		if (ret < 0) {
+			dev_err(dev, "Unique device id conversion error: %d\n", ret);
+			return ret;
+		}
+
+		if (soc_intel_is_byt_cr(pdev))
+			byt_rvp_platform_data.res_info = &bytcr_res_info;
 	}
 
 	dev_dbg(dev, "ACPI device id: %x\n", dev_id);
@@ -281,11 +331,6 @@
 	if (ret < 0)
 		return ret;
 
-	if (soc_intel_is_byt_cr(pdev)) {
-		/* override resource info */
-		byt_rvp_platform_data.res_info = &bytcr_res_info;
-	}
-
 	/* update machine parameters */
 	mach->mach_params.acpi_ipc_irq_index =
 		pdata->res_info->acpi_ipc_irq_index;
@@ -346,6 +391,7 @@
 }
 
 static const struct acpi_device_id sst_acpi_ids[] = {
+	{ "LPE0F28", (unsigned long)&snd_soc_acpi_intel_baytrail_machines},
 	{ "80860F28", (unsigned long)&snd_soc_acpi_intel_baytrail_machines},
 	{ "808622A8", (unsigned long)&snd_soc_acpi_intel_cherrytrail_machines},
 	{ },
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bdw-rt5650.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bdw-rt5650.c
@@ -299,7 +299,7 @@
 	if (!bdw_rt5650)
 		return -ENOMEM;
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	ret = snd_soc_fixup_dai_links_platform_name(&bdw_rt5650_card,
 						    mach->mach_params.platform);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bdw-rt5677.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bdw-rt5677.c
@@ -426,7 +426,7 @@
 	if (!bdw_rt5677)
 		return -ENOMEM;
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	ret = snd_soc_fixup_dai_links_platform_name(&bdw_rt5677_card,
 						    mach->mach_params.platform);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/broadwell.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/broadwell.c
@@ -292,7 +292,7 @@
 
 	broadwell_rt286.dev = &pdev->dev;
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	ret = snd_soc_fixup_dai_links_platform_name(&broadwell_rt286,
 						    mach->mach_params.platform);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bxt_da7219_max98357a.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bxt_da7219_max98357a.c
@@ -750,6 +750,7 @@
 	.dapm_routes = audio_map,
 	.num_dapm_routes = ARRAY_SIZE(audio_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = bxt_card_late_probe,
 };
 
@@ -825,7 +826,7 @@
 		}
 	}
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	platform_name = mach->mach_params.platform;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bxt_rt298.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bxt_rt298.c
@@ -575,6 +575,7 @@
 	.dapm_routes = broxton_rt298_map,
 	.num_dapm_routes = ARRAY_SIZE(broxton_rt298_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = bxt_card_late_probe,
 
 };
@@ -628,7 +629,7 @@
 	card->dev = &pdev->dev;
 	snd_soc_card_set_drvdata(card, ctx);
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	platform_name = mach->mach_params.platform;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bytcht_cx2072x.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bytcht_cx2072x.c
@@ -257,7 +257,7 @@
 		byt_cht_cx2072x_dais[dai_index].codecs->name = codec_name;
 	}
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	ret = snd_soc_fixup_dai_links_platform_name(&byt_cht_cx2072x_card,
 						    mach->mach_params.platform);
 	if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bytcht_da7213.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bytcht_da7213.c
@@ -260,7 +260,7 @@
 		dailink[dai_index].codecs->name = codec_name;
 	}
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	platform_name = mach->mach_params.platform;
 
 	ret_val = snd_soc_fixup_dai_links_platform_name(card, platform_name);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bytcht_es8316.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bytcht_es8316.c
@@ -443,6 +443,13 @@
 					| BYT_CHT_ES8316_INTMIC_IN2_MAP
 					| BYT_CHT_ES8316_JD_INVERTED),
 	},
+	{	/* Nanote UMPC-01 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "RWC CO.,LTD"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "UMPC-01"),
+		},
+		.driver_data = (void *)BYT_CHT_ES8316_INTMIC_IN1_MAP,
+	},
 	{	/* Teclast X98 Plus II */
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "TECLAST"),
@@ -490,21 +497,28 @@
 	if (adev) {
 		snprintf(codec_name, sizeof(codec_name),
 			 "i2c-%s", acpi_dev_name(adev));
-		put_device(&adev->dev);
 		byt_cht_es8316_dais[dai_index].codecs->name = codec_name;
 	} else {
 		dev_err(dev, "Error cannot find '%s' dev\n", mach->id);
 		return -ENXIO;
 	}
 
-	/* override plaform name, if required */
+	codec_dev = acpi_get_first_physical_node(adev);
+	acpi_dev_put(adev);
+	if (!codec_dev)
+		return -EPROBE_DEFER;
+	priv->codec_dev = get_device(codec_dev);
+
+	/* override platform name, if required */
 	byt_cht_es8316_card.dev = dev;
 	platform_name = mach->mach_params.platform;
 
 	ret = snd_soc_fixup_dai_links_platform_name(&byt_cht_es8316_card,
 						    platform_name);
-	if (ret)
+	if (ret) {
+		put_device(codec_dev);
 		return ret;
+	}
 
 	/* Check for BYTCR or other platform and setup quirks */
 	dmi_id = dmi_first_match(byt_cht_es8316_quirk_table);
@@ -532,14 +546,10 @@
 
 	/* get the clock */
 	priv->mclk = devm_clk_get(dev, "pmc_plt_clk_3");
-	if (IS_ERR(priv->mclk))
+	if (IS_ERR(priv->mclk)) {
+		put_device(codec_dev);
 		return dev_err_probe(dev, PTR_ERR(priv->mclk), "clk_get pmc_plt_clk_3 failed\n");
-
-	/* get speaker enable GPIO */
-	codec_dev = acpi_get_first_physical_node(adev);
-	if (!codec_dev)
-		return -EPROBE_DEFER;
-	priv->codec_dev = get_device(codec_dev);
+	}
 
 	if (quirk & BYT_CHT_ES8316_JD_INVERTED)
 		props[cnt++] = PROPERTY_ENTRY_BOOL("everest,jack-detect-inverted");
@@ -561,6 +571,7 @@
 		}
 	}
 
+	/* get speaker enable GPIO */
 	devm_acpi_dev_add_driver_gpios(codec_dev, byt_cht_es8316_gpios);
 	priv->speaker_en_gpio =
 		gpiod_get_optional(codec_dev, "speaker-enable",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bytcr_rt5640.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bytcr_rt5640.c
@@ -17,6 +17,7 @@
 #include <linux/acpi.h>
 #include <linux/clk.h>
 #include <linux/device.h>
+#include <linux/device/bus.h>
 #include <linux/dmi.h>
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/machine.h>
@@ -32,6 +33,8 @@
 #include "../atom/sst-atom-controls.h"
 #include "../common/soc-intel-quirks.h"
 
+#define BYT_RT5640_FALLBACK_CODEC_DEV_NAME	"i2c-rt5640"
+
 enum {
 	BYT_RT5640_DMIC1_MAP,
 	BYT_RT5640_DMIC2_MAP,
@@ -533,6 +536,18 @@
 
 /* Please keep this list alphabetically sorted */
 static const struct dmi_system_id byt_rt5640_quirk_table[] = {
+	{	/* Acer Iconia One 7 B1-750 */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Insyde"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "VESPA2"),
+		},
+		.driver_data = (void *)(BYT_RT5640_DMIC1_MAP |
+					BYT_RT5640_JD_SRC_JD1_IN4P |
+					BYT_RT5640_OVCD_TH_1500UA |
+					BYT_RT5640_OVCD_SF_0P75 |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
 	{	/* Acer Iconia Tab 8 W1-810 */
 		.matches = {
 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"),
@@ -571,6 +586,21 @@
 					BYT_RT5640_MCLK_EN),
 	},
 	{
+		/* Advantech MICA-071 */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Advantech"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "MICA-071"),
+		},
+		/* OVCD Th = 1500uA to reliable detect head-phones vs -set */
+		.driver_data = (void *)(BYT_RT5640_IN3_MAP |
+					BYT_RT5640_JD_SRC_JD2_IN4N |
+					BYT_RT5640_OVCD_TH_1500UA |
+					BYT_RT5640_OVCD_SF_0P75 |
+					BYT_RT5640_MONO_SPEAKER |
+					BYT_RT5640_DIFF_MIC |
+					BYT_RT5640_MCLK_EN),
+	},
+	{
 		.matches = {
 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "ARCHOS"),
 			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "ARCHOS 80 Cesium"),
@@ -583,6 +613,17 @@
 	{
 		.matches = {
 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "ARCHOS"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "ARCHOS 101 CESIUM"),
+		},
+		.driver_data = (void *)(BYTCR_INPUT_DEFAULTS |
+					BYT_RT5640_JD_NOT_INV |
+					BYT_RT5640_DIFF_MIC |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
+	{
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "ARCHOS"),
 			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "ARCHOS 140 CESIUM"),
 		},
 		.driver_data = (void *)(BYT_RT5640_IN1_MAP |
@@ -641,6 +682,18 @@
 					BYT_RT5640_SSP0_AIF1 |
 					BYT_RT5640_MCLK_EN),
 	},
+	{	/* Chuwi Vi8 dual-boot (CWI506) */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Insyde"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "i86"),
+			/* The above are too generic, also match BIOS info */
+			DMI_MATCH(DMI_BIOS_VERSION, "CHUWI2.D86JHBNR02"),
+		},
+		.driver_data = (void *)(BYTCR_INPUT_DEFAULTS |
+					BYT_RT5640_MONO_SPEAKER |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
 	{
 		/* Chuwi Vi10 (CWI505) */
 		.matches = {
@@ -759,6 +812,18 @@
 					BYT_RT5640_OVCD_SF_0P75 |
 					BYT_RT5640_MCLK_EN),
 	},
+	{	/* HP Pro Tablet 408 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pro Tablet 408"),
+		},
+		.driver_data = (void *)(BYT_RT5640_DMIC1_MAP |
+					BYT_RT5640_JD_SRC_JD2_IN4N |
+					BYT_RT5640_OVCD_TH_1500UA |
+					BYT_RT5640_OVCD_SF_0P75 |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
 	{	/* HP Stream 7 */
 		.matches = {
 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
@@ -831,6 +896,18 @@
 					BYT_RT5640_SSP0_AIF1 |
 					BYT_RT5640_MCLK_EN),
 	},
+	{
+		/* Medion Lifetab S10346 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "Aptio CRB"),
+			/* Above strings are much too generic, also match on BIOS date */
+			DMI_MATCH(DMI_BIOS_DATE, "10/22/2015"),
+		},
+		.driver_data = (void *)(BYTCR_INPUT_DEFAULTS |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
 	{	/* Mele PCG03 Mini PC */
 		.matches = {
 			DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "Mini PC"),
@@ -1025,6 +1102,36 @@
 					BYT_RT5640_SSP0_AIF2 |
 					BYT_RT5640_MCLK_EN),
 	},
+	{
+		/* Vexia Edu Atla 10 tablet 5V version */
+		.matches = {
+			/* Having all 3 of these not set is somewhat unique */
+			DMI_MATCH(DMI_SYS_VENDOR, "To be filled by O.E.M."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "To be filled by O.E.M."),
+			DMI_MATCH(DMI_BOARD_NAME, "To be filled by O.E.M."),
+			/* Above strings are too generic, also match on BIOS date */
+			DMI_MATCH(DMI_BIOS_DATE, "05/14/2015"),
+		},
+		.driver_data = (void *)(BYTCR_INPUT_DEFAULTS |
+					BYT_RT5640_JD_NOT_INV |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
+	{	/* Vexia Edu Atla 10 tablet 9V version */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "Aptio CRB"),
+			/* Above strings are too generic, also match on BIOS date */
+			DMI_MATCH(DMI_BIOS_DATE, "08/25/2014"),
+		},
+		.driver_data = (void *)(BYT_RT5640_IN1_MAP |
+					BYT_RT5640_JD_SRC_JD2_IN4N |
+					BYT_RT5640_OVCD_TH_2000UA |
+					BYT_RT5640_OVCD_SF_0P75 |
+					BYT_RT5640_DIFF_MIC |
+					BYT_RT5640_SSP0_AIF2 |
+					BYT_RT5640_MCLK_EN),
+	},
 	{	/* Voyo Winpad A15 */
 		.matches = {
 			DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
@@ -1534,13 +1641,42 @@
 	if (adev) {
 		snprintf(byt_rt5640_codec_name, sizeof(byt_rt5640_codec_name),
 			 "i2c-%s", acpi_dev_name(adev));
-		put_device(&adev->dev);
 		byt_rt5640_dais[dai_index].codecs->name = byt_rt5640_codec_name;
 	} else {
 		dev_err(&pdev->dev, "Error cannot find '%s' dev\n", mach->id);
 		return -ENXIO;
 	}
 
+	codec_dev = acpi_get_first_physical_node(adev);
+	acpi_dev_put(adev);
+
+	if (codec_dev) {
+		priv->codec_dev = get_device(codec_dev);
+	} else {
+		/*
+		 * Special case for Android tablets where the codec i2c_client
+		 * has been manually instantiated by x86_android_tablets.ko due
+		 * to a broken DSDT.
+		 */
+		codec_dev = bus_find_device_by_name(&i2c_bus_type, NULL,
+					BYT_RT5640_FALLBACK_CODEC_DEV_NAME);
+		if (!codec_dev)
+			return -EPROBE_DEFER;
+
+		if (!i2c_verify_client(codec_dev)) {
+			dev_err(dev, "Error '%s' is not an i2c_client\n",
+				BYT_RT5640_FALLBACK_CODEC_DEV_NAME);
+			put_device(codec_dev);
+		}
+
+		/* fixup codec name */
+		strscpy(byt_rt5640_codec_name, BYT_RT5640_FALLBACK_CODEC_DEV_NAME,
+			sizeof(byt_rt5640_codec_name));
+
+		/* bus_find_device() returns a reference no need to get() */
+		priv->codec_dev = codec_dev;
+	}
+
 	/*
 	 * swap SSP0 if bytcr is detected
 	 * (will be overridden if DMI quirk is detected)
@@ -1615,11 +1751,6 @@
 		byt_rt5640_quirk = quirk_override;
 	}
 
-	codec_dev = acpi_get_first_physical_node(adev);
-	if (!codec_dev)
-		return -EPROBE_DEFER;
-	priv->codec_dev = get_device(codec_dev);
-
 	if (byt_rt5640_quirk & BYT_RT5640_JD_HP_ELITEP_1000G2) {
 		acpi_dev_add_driver_gpios(ACPI_COMPANION(priv->codec_dev),
 					  byt_rt5640_hp_elitepad_1000g2_gpios);
@@ -1706,7 +1837,7 @@
 	byt_rt5640_card.long_name = byt_rt5640_long_name;
 #endif
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	platform_name = mach->mach_params.platform;
 
 	ret_val = snd_soc_fixup_dai_links_platform_name(&byt_rt5640_card,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bytcr_rt5651.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bytcr_rt5651.c
@@ -930,7 +930,6 @@
 	if (adev) {
 		snprintf(byt_rt5651_codec_name, sizeof(byt_rt5651_codec_name),
 			 "i2c-%s", acpi_dev_name(adev));
-		put_device(&adev->dev);
 		byt_rt5651_dais[dai_index].codecs->name = byt_rt5651_codec_name;
 	} else {
 		dev_err(&pdev->dev, "Error cannot find '%s' dev\n", mach->id);
@@ -938,6 +937,7 @@
 	}
 
 	codec_dev = acpi_get_first_physical_node(adev);
+	acpi_dev_put(adev);
 	if (!codec_dev)
 		return -EPROBE_DEFER;
 	priv->codec_dev = get_device(codec_dev);
@@ -1104,7 +1104,7 @@
 	byt_rt5651_card.long_name = byt_rt5651_long_name;
 #endif
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	platform_name = mach->mach_params.platform;
 
 	ret_val = snd_soc_fixup_dai_links_platform_name(&byt_rt5651_card,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/bytcr_wm5102.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/bytcr_wm5102.c
@@ -411,9 +411,9 @@
 		return -ENOENT;
 	}
 	snprintf(codec_name, sizeof(codec_name), "spi-%s", acpi_dev_name(adev));
-	put_device(&adev->dev);
 
 	codec_dev = bus_find_device_by_name(&spi_bus_type, NULL, codec_name);
+	acpi_dev_put(adev);
 	if (!codec_dev)
 		return -EPROBE_DEFER;
 
@@ -421,8 +421,17 @@
 	priv->spkvdd_en_gpio = gpiod_get(codec_dev, "wlf,spkvdd-ena", GPIOD_OUT_LOW);
 	put_device(codec_dev);
 
-	if (IS_ERR(priv->spkvdd_en_gpio))
-		return dev_err_probe(dev, PTR_ERR(priv->spkvdd_en_gpio), "getting spkvdd-GPIO\n");
+	if (IS_ERR(priv->spkvdd_en_gpio)) {
+		ret = PTR_ERR(priv->spkvdd_en_gpio);
+		/*
+		 * The spkvdd gpio-lookup is registered by: drivers/mfd/arizona-spi.c,
+		 * so -ENOENT means that arizona-spi hasn't probed yet.
+		 */
+		if (ret == -ENOENT)
+			ret = -EPROBE_DEFER;
+
+		return dev_err_probe(dev, ret, "getting spkvdd-GPIO\n");
+	}
 
 	/* override platform name, if required */
 	byt_wm5102_card.dev = dev;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/cht_bsw_max98090_ti.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/cht_bsw_max98090_ti.c
@@ -296,7 +296,7 @@
 	int ret;
 
 	/*
-	 * TI supports 4 butons headset detection
+	 * TI supports 4 buttons headset detection
 	 * KEY_MEDIA
 	 * KEY_VOICECOMMAND
 	 * KEY_VOLUMEUP
@@ -558,7 +558,7 @@
 			dev_dbg(dev, "Unable to add GPIO mapping table\n");
 	}
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	snd_soc_card_cht.dev = &pdev->dev;
 	mach = pdev->dev.platform_data;
 	platform_name = mach->mach_params.platform;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/cht_bsw_nau8824.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/cht_bsw_nau8824.c
@@ -100,7 +100,7 @@
 	struct snd_soc_component *component = codec_dai->component;
 	int ret, jack_type;
 
-	/* NAU88L24 supports 4 butons headset detection
+	/* NAU88L24 supports 4 buttons headset detection
 	 * KEY_PLAYPAUSE
 	 * KEY_VOICECOMMAND
 	 * KEY_VOLUMEUP
@@ -257,7 +257,7 @@
 		return -ENOMEM;
 	snd_soc_card_set_drvdata(&snd_soc_card_cht, drv);
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	snd_soc_card_cht.dev = &pdev->dev;
 	mach = pdev->dev.platform_data;
 	platform_name = mach->mach_params.platform;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/cht_bsw_rt5645.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/cht_bsw_rt5645.c
@@ -653,7 +653,7 @@
 	    (cht_rt5645_quirk & CHT_RT5645_SSP0_AIF2))
 		cht_dailink[dai_index].cpus->dai_name = "ssp0-port";
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	platform_name = mach->mach_params.platform;
 
 	ret_val = snd_soc_fixup_dai_links_platform_name(card,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/cht_bsw_rt5672.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/cht_bsw_rt5672.c
@@ -483,7 +483,7 @@
 		drv->use_ssp0 = true;
 	}
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	snd_soc_card_cht.dev = &pdev->dev;
 	platform_name = mach->mach_params.platform;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/glk_rt5682_max98357a.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/glk_rt5682_max98357a.c
@@ -603,8 +603,10 @@
 	card = &glk_audio_card_rt5682_m98357a;
 	card->dev = &pdev->dev;
 	snd_soc_card_set_drvdata(card, ctx);
+	if (!snd_soc_acpi_sof_parent(&pdev->dev))
+		card->disable_route_checks = true;
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	platform_name = mach->mach_params.platform;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/haswell.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/haswell.c
@@ -175,7 +175,7 @@
 
 	haswell_rt5640.dev = &pdev->dev;
 
-	/* override plaform name, if required */
+	/* override platform name, if required */
 	mach = pdev->dev.platform_data;
 	ret = snd_soc_fixup_dai_links_platform_name(&haswell_rt5640,
 						    mach->mach_params.platform);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/kbl_da7219_max98357a.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/kbl_da7219_max98357a.c
@@ -621,6 +621,7 @@
 	.dapm_routes = kabylake_map,
 	.num_dapm_routes = ARRAY_SIZE(kabylake_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/kbl_da7219_max98927.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/kbl_da7219_max98927.c
@@ -1018,6 +1018,7 @@
 	.codec_conf = max98927_codec_conf,
 	.num_configs = ARRAY_SIZE(max98927_codec_conf),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
@@ -1036,6 +1037,7 @@
 	.codec_conf = max98927_codec_conf,
 	.num_configs = ARRAY_SIZE(max98927_codec_conf),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
@@ -1053,6 +1055,7 @@
 	.codec_conf = max98373_codec_conf,
 	.num_configs = ARRAY_SIZE(max98373_codec_conf),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
@@ -1070,6 +1073,7 @@
 	.codec_conf = max98373_codec_conf,
 	.num_configs = ARRAY_SIZE(max98373_codec_conf),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/kbl_rt5660.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/kbl_rt5660.c
@@ -519,6 +519,7 @@
 	.dapm_routes = kabylake_rt5660_map,
 	.num_dapm_routes = ARRAY_SIZE(kabylake_rt5660_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/kbl_rt5663_max98927.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/kbl_rt5663_max98927.c
@@ -954,6 +954,7 @@
 	.codec_conf = max98927_codec_conf,
 	.num_configs = ARRAY_SIZE(max98927_codec_conf),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
@@ -970,6 +971,7 @@
 	.dapm_routes = kabylake_5663_map,
 	.num_dapm_routes = ARRAY_SIZE(kabylake_5663_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/kbl_rt5663_rt5514_max98927.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/kbl_rt5663_rt5514_max98927.c
@@ -779,6 +779,7 @@
 	.codec_conf = max98927_codec_conf,
 	.num_configs = ARRAY_SIZE(max98927_codec_conf),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = kabylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/skl_hda_dsp_generic.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/skl_hda_dsp_generic.c
@@ -229,6 +229,8 @@
 	ctx->common_hdmi_codec_drv = mach->mach_params.common_hdmi_codec_drv;
 
 	hda_soc_card.dev = &pdev->dev;
+	if (!snd_soc_acpi_sof_parent(&pdev->dev))
+		hda_soc_card.disable_route_checks = true;
 
 	if (mach->mach_params.dmic_num > 0) {
 		snprintf(hda_soc_components, sizeof(hda_soc_components),
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/skl_nau88l25_max98357a.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/skl_nau88l25_max98357a.c
@@ -643,6 +643,7 @@
 	.dapm_routes = skylake_map,
 	.num_dapm_routes = ARRAY_SIZE(skylake_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = skylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/skl_rt286.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/skl_rt286.c
@@ -524,6 +524,7 @@
 	.dapm_routes = skylake_rt286_map,
 	.num_dapm_routes = ARRAY_SIZE(skylake_rt286_map),
 	.fully_routed = true,
+	.disable_route_checks = true,
 	.late_probe = skylake_card_late_probe,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/sof_cs42l42.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/sof_cs42l42.c
@@ -311,6 +311,9 @@
 	links[*id].platforms = platform_component;
 	links[*id].num_platforms = ARRAY_SIZE(platform_component);
 	links[*id].dpcm_playback = 1;
+	/* firmware-generated echo reference */
+	links[*id].dpcm_capture = 1;
+
 	links[*id].no_pcm = 1;
 	links[*id].cpus = &cpus[*id];
 	links[*id].num_cpus = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/sof_rt5682.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/sof_rt5682.c
@@ -737,8 +737,6 @@
 			links[id].num_codecs = ARRAY_SIZE(max_98373_components);
 			links[id].init = max_98373_spk_codec_init;
 			links[id].ops = &max_98373_ops;
-			/* feedback stream */
-			links[id].dpcm_capture = 1;
 		} else if (sof_rt5682_quirk &
 				SOF_MAX98360A_SPEAKER_AMP_PRESENT) {
 			max_98360a_dai_link(&links[id]);
@@ -751,6 +749,9 @@
 		links[id].platforms = platform_component;
 		links[id].num_platforms = ARRAY_SIZE(platform_component);
 		links[id].dpcm_playback = 1;
+		/* feedback stream or firmware-generated echo reference */
+		links[id].dpcm_capture = 1;
+
 		links[id].no_pcm = 1;
 		links[id].cpus = &cpus[id];
 		links[id].num_cpus = 1;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/sof_sdw.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/sof_sdw.c
@@ -36,8 +36,6 @@
 	if (SOF_SSP_GET_PORT(sof_sdw_quirk))
 		dev_dbg(dev, "SSP port %ld\n",
 			SOF_SSP_GET_PORT(sof_sdw_quirk));
-	if (sof_sdw_quirk & SOF_RT715_DAI_ID_FIX)
-		dev_dbg(dev, "quirk SOF_RT715_DAI_ID_FIX enabled\n");
 	if (sof_sdw_quirk & SOF_SDW_NO_AGGREGATION)
 		dev_dbg(dev, "quirk SOF_SDW_NO_AGGREGATION enabled\n");
 }
@@ -64,8 +62,7 @@
 			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
 			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "09C6")
 		},
-		.driver_data = (void *)(RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX),
+		.driver_data = (void *)RT711_JD2,
 	},
 	{
 		/* early version of SKU 09C6 */
@@ -74,8 +71,7 @@
 			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
 			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0983")
 		},
-		.driver_data = (void *)(RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX),
+		.driver_data = (void *)RT711_JD2,
 	},
 	{
 		.callback = sof_sdw_quirk_cb,
@@ -84,7 +80,6 @@
 			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "098F"),
 		},
 		.driver_data = (void *)(RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX |
 					SOF_SDW_FOUR_SPK),
 	},
 	{
@@ -94,7 +89,6 @@
 			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0990"),
 		},
 		.driver_data = (void *)(RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX |
 					SOF_SDW_FOUR_SPK),
 	},
 	/* IceLake devices */
@@ -126,8 +120,7 @@
 			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0A3E")
 		},
 		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
-					RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX),
+					RT711_JD2),
 	},
 	{
 		/* Dell XPS 9710 */
@@ -138,7 +131,6 @@
 		},
 		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
 					RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX |
 					SOF_SDW_FOUR_SPK),
 	},
 	{
@@ -149,7 +141,6 @@
 		},
 		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
 					RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX |
 					SOF_SDW_FOUR_SPK),
 	},
 	{
@@ -184,11 +175,11 @@
 		.callback = sof_sdw_quirk_cb,
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "HP"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "HP Spectre x360 Convertible"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Spectre x360 Conv"),
 		},
 		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
 					SOF_SDW_PCH_DMIC |
-					RT711_JD2),
+					RT711_JD1),
 	},
 	{
 		/* NUC15 'Bishop County' LAPBC510 and LAPBC710 skews */
@@ -201,6 +192,28 @@
 					SOF_SDW_PCH_DMIC |
 					RT711_JD1),
 	},
+	{
+		/* NUC15 LAPBC710 skews */
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
+			DMI_MATCH(DMI_BOARD_NAME, "LAPBC710"),
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					SOF_SDW_PCH_DMIC |
+					RT711_JD1),
+	},
+	{
+		/* NUC15 'Rooks County' LAPRC510 and LAPRC710 skews */
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Intel(R) Client Systems"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LAPRC"),
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					SOF_SDW_PCH_DMIC |
+					RT711_JD2_100K),
+	},
 	/* TigerLake-SDCA devices */
 	{
 		.callback = sof_sdw_quirk_cb,
@@ -210,9 +223,17 @@
 		},
 		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
 					RT711_JD2 |
-					SOF_RT715_DAI_ID_FIX |
 					SOF_SDW_FOUR_SPK),
 	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0A45")
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2),
+	},
 	/* AlderLake devices */
 	{
 		.callback = sof_sdw_quirk_cb,
@@ -222,7 +243,6 @@
 		},
 		.driver_data = (void *)(RT711_JD2_100K |
 					SOF_SDW_TGL_HDMI |
-					SOF_RT715_DAI_ID_FIX |
 					SOF_BT_OFFLOAD_SSP(2) |
 					SOF_SSP_BT_OFFLOAD_PRESENT),
 	},
@@ -238,6 +258,84 @@
 					SOF_BT_OFFLOAD_SSP(2) |
 					SOF_SSP_BT_OFFLOAD_PRESENT),
 	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
+			DMI_MATCH(DMI_PRODUCT_SKU, "0000000000070000"),
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2_100K),
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0AF3"),
+		},
+		/* No Jack */
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					SOF_SDW_FOUR_SPK),
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0B00")
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2 |
+					SOF_SDW_FOUR_SPK),
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0B01")
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2 |
+					SOF_SDW_FOUR_SPK),
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0B11")
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2 |
+					SOF_SDW_FOUR_SPK),
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0B12")
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2 |
+					SOF_SDW_FOUR_SPK),
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0B13"),
+		},
+		/* No Jack */
+		.driver_data = (void *)SOF_SDW_TGL_HDMI,
+	},
+	{
+		.callback = sof_sdw_quirk_cb,
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "0B29"),
+		},
+		.driver_data = (void *)(SOF_SDW_TGL_HDMI |
+					RT711_JD2 |
+					SOF_SDW_FOUR_SPK),
+	},
 	{}
 };
 
@@ -270,7 +368,7 @@
 	/* Find stream from first CPU DAI */
 	dai = asoc_rtd_to_cpu(rtd, 0);
 
-	sdw_stream = snd_soc_dai_get_sdw_stream(dai, substream->stream);
+	sdw_stream = snd_soc_dai_get_stream(dai, substream->stream);
 
 	if (IS_ERR(sdw_stream)) {
 		dev_err(rtd->dev, "no stream found for DAI %s", dai->name);
@@ -290,7 +388,7 @@
 	/* Find stream from first CPU DAI */
 	dai = asoc_rtd_to_cpu(rtd, 0);
 
-	sdw_stream = snd_soc_dai_get_sdw_stream(dai, substream->stream);
+	sdw_stream = snd_soc_dai_get_stream(dai, substream->stream);
 
 	if (IS_ERR(sdw_stream)) {
 		dev_err(rtd->dev, "no stream found for DAI %s", dai->name);
@@ -329,7 +427,7 @@
 	/* Find stream from first CPU DAI */
 	dai = asoc_rtd_to_cpu(rtd, 0);
 
-	sdw_stream = snd_soc_dai_get_sdw_stream(dai, substream->stream);
+	sdw_stream = snd_soc_dai_get_stream(dai, substream->stream);
 
 	if (IS_ERR(sdw_stream)) {
 		dev_err(rtd->dev, "no stream found for DAI %s", dai->name);
@@ -352,26 +450,13 @@
 	.shutdown = sdw_shutdown,
 };
 
-static int sof_sdw_mic_codec_mockup_init(struct snd_soc_card *card,
-					 const struct snd_soc_acpi_link_adr *link,
-					 struct snd_soc_dai_link *dai_links,
-					 struct sof_sdw_codec_info *info,
-					 bool playback)
-{
-	/*
-	 * force DAI link to use same ID as RT715 and DMIC
-	 * to reuse topologies
-	 */
-	dai_links->id = SDW_DMIC_DAI_ID;
-	return 0;
-}
-
 static struct sof_sdw_codec_info codec_info_list[] = {
 	{
 		.part_id = 0x700,
 		.direction = {true, true},
 		.dai_name = "rt700-aif1",
 		.init = sof_sdw_rt700_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_JACK,
 	},
 	{
 		.part_id = 0x711,
@@ -380,6 +465,7 @@
 		.dai_name = "rt711-sdca-aif1",
 		.init = sof_sdw_rt711_sdca_init,
 		.exit = sof_sdw_rt711_sdca_exit,
+		.codec_type = SOF_SDW_CODEC_TYPE_JACK,
 	},
 	{
 		.part_id = 0x711,
@@ -388,6 +474,7 @@
 		.dai_name = "rt711-aif1",
 		.init = sof_sdw_rt711_init,
 		.exit = sof_sdw_rt711_exit,
+		.codec_type = SOF_SDW_CODEC_TYPE_JACK,
 	},
 	{
 		.part_id = 0x1308,
@@ -396,12 +483,14 @@
 		.dai_name = "rt1308-aif",
 		.ops = &sof_sdw_rt1308_i2s_ops,
 		.init = sof_sdw_rt1308_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_AMP,
 	},
 	{
 		.part_id = 0x1316,
 		.direction = {true, true},
 		.dai_name = "rt1316-aif",
 		.init = sof_sdw_rt1316_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_AMP,
 	},
 	{
 		.part_id = 0x714,
@@ -410,6 +499,7 @@
 		.ignore_pch_dmic = true,
 		.dai_name = "rt715-aif2",
 		.init = sof_sdw_rt715_sdca_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_MIC,
 	},
 	{
 		.part_id = 0x715,
@@ -418,6 +508,7 @@
 		.ignore_pch_dmic = true,
 		.dai_name = "rt715-aif2",
 		.init = sof_sdw_rt715_sdca_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_MIC,
 	},
 	{
 		.part_id = 0x714,
@@ -426,6 +517,7 @@
 		.ignore_pch_dmic = true,
 		.dai_name = "rt715-aif2",
 		.init = sof_sdw_rt715_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_MIC,
 	},
 	{
 		.part_id = 0x715,
@@ -434,6 +526,7 @@
 		.ignore_pch_dmic = true,
 		.dai_name = "rt715-aif2",
 		.init = sof_sdw_rt715_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_MIC,
 	},
 	{
 		.part_id = 0x8373,
@@ -441,12 +534,14 @@
 		.dai_name = "max98373-aif1",
 		.init = sof_sdw_mx8373_init,
 		.codec_card_late_probe = sof_sdw_mx8373_late_probe,
+		.codec_type = SOF_SDW_CODEC_TYPE_AMP,
 	},
 	{
 		.part_id = 0x5682,
 		.direction = {true, true},
 		.dai_name = "rt5682-sdw",
 		.init = sof_sdw_rt5682_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_JACK,
 	},
 	{
 		.part_id = 0xaaaa, /* generic codec mockup */
@@ -454,6 +549,7 @@
 		.direction = {true, true},
 		.dai_name = "sdw-mockup-aif1",
 		.init = NULL,
+		.codec_type = SOF_SDW_CODEC_TYPE_JACK,
 	},
 	{
 		.part_id = 0xaa55, /* headset codec mockup */
@@ -461,6 +557,7 @@
 		.direction = {true, true},
 		.dai_name = "sdw-mockup-aif1",
 		.init = NULL,
+		.codec_type = SOF_SDW_CODEC_TYPE_JACK,
 	},
 	{
 		.part_id = 0x55aa, /* amplifier mockup */
@@ -468,13 +565,14 @@
 		.direction = {true, false},
 		.dai_name = "sdw-mockup-aif1",
 		.init = NULL,
+		.codec_type = SOF_SDW_CODEC_TYPE_AMP,
 	},
 	{
 		.part_id = 0x5555,
 		.version_id = 0,
 		.direction = {false, true},
 		.dai_name = "sdw-mockup-aif1",
-		.init = sof_sdw_mic_codec_mockup_init,
+		.codec_type = SOF_SDW_CODEC_TYPE_MIC,
 	},
 };
 
@@ -522,10 +620,11 @@
  * Since some sdw slaves may be aggregated, the CPU DAI number
  * may be larger than the number of BE dailinks.
  */
-static int get_sdw_dailink_info(const struct snd_soc_acpi_link_adr *links,
+static int get_sdw_dailink_info(struct device *dev, const struct snd_soc_acpi_link_adr *links,
 				int *sdw_be_num, int *sdw_cpu_dai_num)
 {
 	const struct snd_soc_acpi_link_adr *link;
+	int _codec_type = SOF_SDW_CODEC_TYPE_JACK;
 	bool group_visited[SDW_MAX_GROUPS];
 	bool no_aggregation;
 	int i;
@@ -551,6 +650,12 @@
 		if (codec_index < 0)
 			return codec_index;
 
+		if (codec_info_list[codec_index].codec_type < _codec_type)
+			dev_warn(dev,
+				 "Unexpected address table ordering. Expected order: jack -> amp -> mic\n");
+
+		_codec_type = codec_info_list[codec_index].codec_type;
+
 		endpoint = link->adr_d->endpoints;
 
 		/* count DAI number for playback and capture */
@@ -809,14 +914,14 @@
 }
 
 static int create_sdw_dailink(struct snd_soc_card *card,
-			      struct device *dev, int *be_index,
+			      struct device *dev, int *link_index,
 			      struct snd_soc_dai_link *dai_links,
 			      int sdw_be_num, int sdw_cpu_dai_num,
 			      struct snd_soc_dai_link_component *cpus,
 			      const struct snd_soc_acpi_link_adr *link,
 			      int *cpu_id, bool *group_generated,
 			      struct snd_soc_codec_conf *codec_conf,
-			      int codec_count,
+			      int codec_count, int *link_id,
 			      int *codec_conf_index,
 			      bool *ignore_pch_dmic)
 {
@@ -874,6 +979,19 @@
 	if (codec_info_list[codec_index].ignore_pch_dmic)
 		*ignore_pch_dmic = true;
 
+	/* Shift the first amplifier's *link_id to SDW_AMP_DAI_ID */
+	if (codec_info_list[codec_index].codec_type == SOF_SDW_CODEC_TYPE_AMP &&
+	    *link_id < SDW_AMP_DAI_ID)
+		*link_id = SDW_AMP_DAI_ID;
+
+	/*
+	 * DAI ID is fixed at SDW_DMIC_DAI_ID for MICs to
+	 * keep sdw DMIC and HDMI setting static in UCM
+	 */
+	if (codec_info_list[codec_index].codec_type == SOF_SDW_CODEC_TYPE_MIC &&
+	    *link_id < SDW_DMIC_DAI_ID)
+		*link_id = SDW_DMIC_DAI_ID;
+
 	cpu_dai_index = *cpu_id;
 	for_each_pcm_streams(stream) {
 		char *name, *cpu_name;
@@ -912,8 +1030,12 @@
 			cpus[cpu_dai_index++].dai_name = cpu_name;
 		}
 
-		if (*be_index >= sdw_be_num) {
-			dev_err(dev, " invalid be dai index %d", *be_index);
+		/*
+		 * We create sdw dai links at first stage, so link index should
+		 * not be larger than sdw_be_num
+		 */
+		if (*link_index >= sdw_be_num) {
+			dev_err(dev, "invalid dai link index %d", *link_index);
 			return -EINVAL;
 		}
 
@@ -924,18 +1046,19 @@
 
 		playback = (stream == SNDRV_PCM_STREAM_PLAYBACK);
 		capture = (stream == SNDRV_PCM_STREAM_CAPTURE);
-		init_dai_link(dev, dai_links + *be_index, *be_index, name,
+		init_dai_link(dev, dai_links + *link_index, (*link_id)++, name,
 			      playback, capture,
 			      cpus + *cpu_id, cpu_dai_num,
 			      codecs, codec_num,
 			      NULL, &sdw_ops);
+
 		/*
 		 * SoundWire DAILINKs use 'stream' functions and Bank Switch operations
 		 * based on wait_for_completion(), tag them as 'nonatomic'.
 		 */
-		dai_links[*be_index].nonatomic = true;
+		dai_links[*link_index].nonatomic = true;
 
-		ret = set_codec_init_func(card, link, dai_links + (*be_index)++,
+		ret = set_codec_init_func(card, link, dai_links + (*link_index)++,
 					  playback, group_id);
 		if (ret < 0) {
 			dev_err(dev, "failed to init codec %d", codec_index);
@@ -949,17 +1072,6 @@
 	return 0;
 }
 
-/*
- * DAI link ID of SSP & DMIC & HDMI are based on last
- * link ID used by sdw link. Since be_id may be changed
- * in init func of sdw codec, it is not equal to be_id
- */
-static inline int get_next_be_id(struct snd_soc_dai_link *links,
-				 int be_id)
-{
-	return links[be_id - 1].id + 1;
-}
-
 #define IDISP_CODEC_MASK	0x4
 
 static int sof_card_codec_conf_alloc(struct device *dev,
@@ -1016,7 +1128,7 @@
 	bool group_generated[SDW_MAX_GROUPS];
 	int ssp_codec_index, ssp_mask;
 	struct snd_soc_dai_link *links;
-	int num_links, link_id = 0;
+	int num_links, link_index = 0;
 	char *name, *cpu_name;
 	int total_cpu_dai_num;
 	int sdw_cpu_dai_num;
@@ -1052,7 +1164,7 @@
 	ssp_num = ssp_codec_index >= 0 ? hweight_long(ssp_mask) : 0;
 	comp_num = hdmi_num + ssp_num;
 
-	ret = get_sdw_dailink_info(mach_params->links,
+	ret = get_sdw_dailink_info(dev, mach_params->links,
 				   &sdw_be_num, &sdw_cpu_dai_num);
 	if (ret < 0) {
 		dev_err(dev, "failed to get sdw link info %d", ret);
@@ -1116,24 +1228,18 @@
 		    group_generated[endpoint->group_id])
 			continue;
 
-		ret = create_sdw_dailink(card, dev, &be_id, links, sdw_be_num,
+		ret = create_sdw_dailink(card, dev, &link_index, links, sdw_be_num,
 					 sdw_cpu_dai_num, cpus, adr_link,
 					 &cpu_id, group_generated,
 					 codec_conf, codec_conf_count,
-					 &codec_conf_index,
+					 &be_id, &codec_conf_index,
 					 &ignore_pch_dmic);
 		if (ret < 0) {
-			dev_err(dev, "failed to create dai link %d", be_id);
-			return -ENOMEM;
+			dev_err(dev, "failed to create dai link %d", link_index);
+			return ret;
 		}
 	}
 
-	/* non-sdw DAI follows sdw DAI */
-	link_id = be_id;
-
-	/* get BE ID for non-sdw DAI */
-	be_id = get_next_be_id(links, be_id);
-
 SSP:
 	/* SSP */
 	if (!ssp_num)
@@ -1173,17 +1279,17 @@
 
 		playback = info->direction[SNDRV_PCM_STREAM_PLAYBACK];
 		capture = info->direction[SNDRV_PCM_STREAM_CAPTURE];
-		init_dai_link(dev, links + link_id, be_id, name,
+		init_dai_link(dev, links + link_index, be_id, name,
 			      playback, capture,
 			      cpus + cpu_id, 1,
 			      ssp_components, 1,
 			      NULL, info->ops);
 
-		ret = info->init(card, NULL, links + link_id, info, 0);
+		ret = info->init(card, NULL, links + link_index, info, 0);
 		if (ret < 0)
 			return ret;
 
-		INC_ID(be_id, cpu_id, link_id);
+		INC_ID(be_id, cpu_id, link_index);
 	}
 
 DMIC:
@@ -1194,21 +1300,21 @@
 			goto HDMI;
 		}
 		cpus[cpu_id].dai_name = "DMIC01 Pin";
-		init_dai_link(dev, links + link_id, be_id, "dmic01",
+		init_dai_link(dev, links + link_index, be_id, "dmic01",
 			      0, 1, // DMIC only supports capture
 			      cpus + cpu_id, 1,
 			      dmic_component, 1,
 			      sof_sdw_dmic_init, NULL);
-		INC_ID(be_id, cpu_id, link_id);
+		INC_ID(be_id, cpu_id, link_index);
 
 		cpus[cpu_id].dai_name = "DMIC16k Pin";
-		init_dai_link(dev, links + link_id, be_id, "dmic16k",
+		init_dai_link(dev, links + link_index, be_id, "dmic16k",
 			      0, 1, // DMIC only supports capture
 			      cpus + cpu_id, 1,
 			      dmic_component, 1,
 			      /* don't call sof_sdw_dmic_init() twice */
 			      NULL, NULL);
-		INC_ID(be_id, cpu_id, link_id);
+		INC_ID(be_id, cpu_id, link_index);
 	}
 
 HDMI:
@@ -1246,12 +1352,12 @@
 			return -ENOMEM;
 
 		cpus[cpu_id].dai_name = cpu_name;
-		init_dai_link(dev, links + link_id, be_id, name,
+		init_dai_link(dev, links + link_index, be_id, name,
 			      1, 0, // HDMI only supports playback
 			      cpus + cpu_id, 1,
 			      idisp_components + i, 1,
 			      sof_sdw_hdmi_init, NULL);
-		INC_ID(be_id, cpu_id, link_id);
+		INC_ID(be_id, cpu_id, link_index);
 	}
 
 	if (sof_sdw_quirk & SOF_SSP_BT_OFFLOAD_PRESENT) {
@@ -1275,7 +1381,7 @@
 			return -ENOMEM;
 
 		cpus[cpu_id].dai_name = cpu_name;
-		init_dai_link(dev, links + link_id, be_id, name, 1, 1,
+		init_dai_link(dev, links + link_index, be_id, name, 1, 1,
 				cpus + cpu_id, 1, ssp_components, 1, NULL, NULL);
 	}
 
@@ -1313,6 +1419,33 @@
 	.late_probe = sof_sdw_card_late_probe,
 };
 
+static void mc_dailink_exit_loop(struct snd_soc_card *card)
+{
+	struct snd_soc_dai_link *link;
+	int ret;
+	int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(codec_info_list); i++) {
+		if (!codec_info_list[i].exit)
+			continue;
+		/*
+		 * We don't need to call .exit function if there is no matched
+		 * dai link found.
+		 */
+		for_each_card_prelinks(card, j, link) {
+			if (!strcmp(link->codecs[0].dai_name,
+				    codec_info_list[i].dai_name)) {
+				ret = codec_info_list[i].exit(card, link);
+				if (ret)
+					dev_warn(card->dev,
+						 "codec exit failed %d\n",
+						 ret);
+				break;
+			}
+		}
+	}
+}
+
 static int mc_probe(struct platform_device *pdev)
 {
 	struct snd_soc_card *card = &card_sof_sdw;
@@ -1377,6 +1510,7 @@
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
 	if (ret) {
 		dev_err(card->dev, "snd_soc_register_card failed %d\n", ret);
+		mc_dailink_exit_loop(card);
 		return ret;
 	}
 
@@ -1388,29 +1522,8 @@
 static int mc_remove(struct platform_device *pdev)
 {
 	struct snd_soc_card *card = platform_get_drvdata(pdev);
-	struct snd_soc_dai_link *link;
-	int ret;
-	int i, j;
 
-	for (i = 0; i < ARRAY_SIZE(codec_info_list); i++) {
-		if (!codec_info_list[i].exit)
-			continue;
-		/*
-		 * We don't need to call .exit function if there is no matched
-		 * dai link found.
-		 */
-		for_each_card_prelinks(card, j, link) {
-			if (!strcmp(link->codecs[0].dai_name,
-				    codec_info_list[i].dai_name)) {
-				ret = codec_info_list[i].exit(card, link);
-				if (ret)
-					dev_warn(&pdev->dev,
-						 "codec exit failed %d\n",
-						 ret);
-				break;
-			}
-		}
-	}
+	mc_dailink_exit_loop(card);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/sof_sdw_common.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/sof_sdw_common.h
@@ -15,6 +15,7 @@
 
 #define MAX_NO_PROPS 2
 #define MAX_HDMI_NUM 4
+#define SDW_AMP_DAI_ID 2
 #define SDW_DMIC_DAI_ID 4
 #define SDW_MAX_CPU_DAIS 16
 #define SDW_INTEL_BIDIR_PDI_BASE 2
@@ -42,7 +43,6 @@
 #define SOF_SDW_PCH_DMIC		BIT(6)
 #define SOF_SSP_PORT(x)		(((x) & GENMASK(5, 0)) << 7)
 #define SOF_SSP_GET_PORT(quirk)	(((quirk) >> 7) & GENMASK(5, 0))
-#define SOF_RT715_DAI_ID_FIX		BIT(13)
 #define SOF_SDW_NO_AGGREGATION		BIT(14)
 
 /* BT audio offload: reserve 3 bits for future */
@@ -52,9 +52,14 @@
 	(((quirk) << SOF_BT_OFFLOAD_SSP_SHIFT) & SOF_BT_OFFLOAD_SSP_MASK)
 #define SOF_SSP_BT_OFFLOAD_PRESENT	BIT(18)
 
+#define SOF_SDW_CODEC_TYPE_JACK		0
+#define SOF_SDW_CODEC_TYPE_AMP		1
+#define SOF_SDW_CODEC_TYPE_MIC		2
+
 struct sof_sdw_codec_info {
 	const int part_id;
 	const int version_id;
+	const int codec_type;
 	int amp_num;
 	const u8 acpi_id[ACPI_ID_LEN];
 	const bool direction[2]; // playback & capture support
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/sof_sdw_rt715.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/sof_sdw_rt715.c
@@ -30,13 +30,6 @@
 		       struct sof_sdw_codec_info *info,
 		       bool playback)
 {
-	/*
-	 * DAI ID is fixed at SDW_DMIC_DAI_ID for 715 to
-	 * keep sdw DMIC and HDMI setting static in UCM
-	 */
-	if (sof_sdw_quirk & SOF_RT715_DAI_ID_FIX)
-		dai_links->id = SDW_DMIC_DAI_ID;
-
 	dai_links->init = rt715_rtd_init;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/boards/sof_sdw_rt715_sdca.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/boards/sof_sdw_rt715_sdca.c
@@ -30,13 +30,6 @@
 			    struct sof_sdw_codec_info *info,
 			    bool playback)
 {
-	/*
-	 * DAI ID is fixed at SDW_DMIC_DAI_ID for 715-SDCA to
-	 * keep sdw DMIC and HDMI setting static in UCM
-	 */
-	if (sof_sdw_quirk & SOF_RT715_DAI_ID_FIX)
-		dai_links->id = SDW_DMIC_DAI_ID;
-
 	dai_links->init = rt715_sdca_rtd_init;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/catpt/dsp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/catpt/dsp.c
@@ -65,6 +65,7 @@
 {
 	struct dma_async_tx_descriptor *desc;
 	enum dma_status status;
+	int ret;
 
 	desc = dmaengine_prep_dma_memcpy(chan, dst_addr, src_addr, size,
 					 DMA_CTRL_ACK);
@@ -77,13 +78,22 @@
 	catpt_updatel_shim(cdev, HMDC,
 			   CATPT_HMDC_HDDA(CATPT_DMA_DEVID, chan->chan_id),
 			   CATPT_HMDC_HDDA(CATPT_DMA_DEVID, chan->chan_id));
-	dmaengine_submit(desc);
+
+	ret = dma_submit_error(dmaengine_submit(desc));
+	if (ret) {
+		dev_err(cdev->dev, "submit tx failed: %d\n", ret);
+		goto clear_hdda;
+	}
+
 	status = dma_wait_for_async_tx(desc);
+	ret = (status == DMA_COMPLETE) ? 0 : -EPROTO;
+
+clear_hdda:
 	/* regardless of status, disable access to HOST memory in demand mode */
 	catpt_updatel_shim(cdev, HMDC,
 			   CATPT_HMDC_HDDA(CATPT_DMA_DEVID, chan->chan_id), 0);
 
-	return (status == DMA_COMPLETE) ? 0 : -EPROTO;
+	return ret;
 }
 
 int catpt_dma_memcpy_todsp(struct catpt_dev *cdev, struct dma_chan *chan,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/common/soc-acpi-intel-adl-match.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/common/soc-acpi-intel-adl-match.c
@@ -74,6 +74,15 @@
 	}
 };
 
+static const struct snd_soc_acpi_adr_device rt711_sdca_2_adr[] = {
+	{
+		.adr = 0x000230025D071101ull,
+		.num_endpoints = 1,
+		.endpoints = &single_endpoint,
+		.name_prefix = "rt711"
+	}
+};
+
 static const struct snd_soc_acpi_adr_device rt1316_1_group1_adr[] = {
 	{
 		.adr = 0x000131025D131601ull, /* unique ID is set for some reason */
@@ -101,6 +110,24 @@
 	}
 };
 
+static const struct snd_soc_acpi_adr_device rt1316_0_group2_adr[] = {
+	{
+		.adr = 0x000031025D131601ull,
+		.num_endpoints = 1,
+		.endpoints = &spk_l_endpoint,
+		.name_prefix = "rt1316-1"
+	}
+};
+
+static const struct snd_soc_acpi_adr_device rt1316_1_group2_adr[] = {
+	{
+		.adr = 0x000130025D131601ull,
+		.num_endpoints = 1,
+		.endpoints = &spk_r_endpoint,
+		.name_prefix = "rt1316-2"
+	}
+};
+
 static const struct snd_soc_acpi_adr_device rt1316_2_single_adr[] = {
 	{
 		.adr = 0x000230025D131601ull,
@@ -209,6 +236,82 @@
 	{}
 };
 
+static const struct snd_soc_acpi_link_adr adl_sdw_rt711_link2_rt1316_link01_rt714_link3[] = {
+	{
+		.mask = BIT(2),
+		.num_adr = ARRAY_SIZE(rt711_sdca_2_adr),
+		.adr_d = rt711_sdca_2_adr,
+	},
+	{
+		.mask = BIT(0),
+		.num_adr = ARRAY_SIZE(rt1316_0_group2_adr),
+		.adr_d = rt1316_0_group2_adr,
+	},
+	{
+		.mask = BIT(1),
+		.num_adr = ARRAY_SIZE(rt1316_1_group2_adr),
+		.adr_d = rt1316_1_group2_adr,
+	},
+	{
+		.mask = BIT(3),
+		.num_adr = ARRAY_SIZE(rt714_3_adr),
+		.adr_d = rt714_3_adr,
+	},
+	{}
+};
+
+static const struct snd_soc_acpi_link_adr adl_sdw_rt711_link2_rt1316_link01[] = {
+	{
+		.mask = BIT(2),
+		.num_adr = ARRAY_SIZE(rt711_sdca_2_adr),
+		.adr_d = rt711_sdca_2_adr,
+	},
+	{
+		.mask = BIT(0),
+		.num_adr = ARRAY_SIZE(rt1316_0_group2_adr),
+		.adr_d = rt1316_0_group2_adr,
+	},
+	{
+		.mask = BIT(1),
+		.num_adr = ARRAY_SIZE(rt1316_1_group2_adr),
+		.adr_d = rt1316_1_group2_adr,
+	},
+	{}
+};
+
+static const struct snd_soc_acpi_link_adr adl_sdw_rt1316_link12_rt714_link0[] = {
+	{
+		.mask = BIT(1),
+		.num_adr = ARRAY_SIZE(rt1316_1_group1_adr),
+		.adr_d = rt1316_1_group1_adr,
+	},
+	{
+		.mask = BIT(2),
+		.num_adr = ARRAY_SIZE(rt1316_2_group1_adr),
+		.adr_d = rt1316_2_group1_adr,
+	},
+	{
+		.mask = BIT(0),
+		.num_adr = ARRAY_SIZE(rt714_0_adr),
+		.adr_d = rt714_0_adr,
+	},
+	{}
+};
+
+static const struct snd_soc_acpi_link_adr adl_sdw_rt1316_link2_rt714_link3[] = {
+	{
+		.mask = BIT(2),
+		.num_adr = ARRAY_SIZE(rt1316_2_single_adr),
+		.adr_d = rt1316_2_single_adr,
+	},
+	{
+		.mask = BIT(3),
+		.num_adr = ARRAY_SIZE(rt714_3_adr),
+		.adr_d = rt714_3_adr,
+	},
+	{}
+};
+
 static const struct snd_soc_acpi_link_adr adl_sdw_rt1316_link2_rt714_link0[] = {
 	{
 		.mask = BIT(2),
@@ -322,6 +425,33 @@
 		.sof_tplg_filename = "sof-adl-rt711-l0-rt1316-l13-rt714-l2.tplg",
 	},
 	{
+		.link_mask = 0xF, /* 4 active links required */
+		.links = adl_sdw_rt711_link2_rt1316_link01_rt714_link3,
+		.drv_name = "sof_sdw",
+		.sof_fw_filename = "sof-adl.ri",
+		.sof_tplg_filename = "sof-adl-rt711-l2-rt1316-l01-rt714-l3.tplg",
+	},
+	{
+		.link_mask = 0x7, /* rt1316 on link0 and link1 & rt711 on link2*/
+		.links = adl_sdw_rt711_link2_rt1316_link01,
+		.drv_name = "sof_sdw",
+		.sof_tplg_filename = "sof-adl-rt711-l2-rt1316-l01.tplg",
+	},
+	{
+		.link_mask = 0xC, /* rt1316 on link2 & rt714 on link3 */
+		.links = adl_sdw_rt1316_link2_rt714_link3,
+		.drv_name = "sof_sdw",
+		.sof_fw_filename = "sof-adl.ri",
+		.sof_tplg_filename = "sof-adl-rt1316-l2-mono-rt714-l3.tplg",
+	},
+	{
+		.link_mask = 0x7, /* rt714 on link0 & two rt1316s on link1 and link2 */
+		.links = adl_sdw_rt1316_link12_rt714_link0,
+		.drv_name = "sof_sdw",
+		.sof_fw_filename = "sof-adl.ri",
+		.sof_tplg_filename = "sof-adl-rt1316-l12-rt714-l0.tplg",
+	},
+	{
 		.link_mask = 0x5, /* 2 active links required */
 		.links = adl_sdw_rt1316_link2_rt714_link0,
 		.drv_name = "sof_sdw",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/common/soc-acpi-intel-tgl-match.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/common/soc-acpi-intel-tgl-match.c
@@ -127,13 +127,13 @@
 	{
 		.adr = 0x000123019F837300ull,
 		.num_endpoints = 1,
-		.endpoints = &spk_l_endpoint,
+		.endpoints = &spk_r_endpoint,
 		.name_prefix = "Right"
 	},
 	{
 		.adr = 0x000127019F837300ull,
 		.num_endpoints = 1,
-		.endpoints = &spk_r_endpoint,
+		.endpoints = &spk_l_endpoint,
 		.name_prefix = "Left"
 	}
 };
@@ -156,6 +156,15 @@
 	}
 };
 
+static const struct snd_soc_acpi_adr_device rt1316_1_single_adr[] = {
+	{
+		.adr = 0x000131025D131601ull,
+		.num_endpoints = 1,
+		.endpoints = &single_endpoint,
+		.name_prefix = "rt1316-1"
+	}
+};
+
 static const struct snd_soc_acpi_adr_device rt1316_1_group1_adr[] = {
 	{
 		.adr = 0x000131025D131601ull, /* unique ID is set for some reason */
@@ -320,6 +329,25 @@
 	{}
 };
 
+static const struct snd_soc_acpi_link_adr tgl_3_in_1_sdca_mono[] = {
+	{
+		.mask = BIT(0),
+		.num_adr = ARRAY_SIZE(rt711_sdca_0_adr),
+		.adr_d = rt711_sdca_0_adr,
+	},
+	{
+		.mask = BIT(1),
+		.num_adr = ARRAY_SIZE(rt1316_1_single_adr),
+		.adr_d = rt1316_1_single_adr,
+	},
+	{
+		.mask = BIT(3),
+		.num_adr = ARRAY_SIZE(rt714_3_adr),
+		.adr_d = rt714_3_adr,
+	},
+	{}
+};
+
 static const struct snd_soc_acpi_codecs tgl_max98373_amp = {
 	.num_codecs = 1,
 	.codecs = {"MX98373"}
@@ -413,6 +441,19 @@
 		.sof_tplg_filename = "sof-tgl-rt711-rt1316-rt714.tplg",
 	},
 	{
+		/*
+		 * link_mask should be 0xB, but all links are enabled by BIOS.
+		 * This entry will be selected if there is no rt1316 amplifier exposed
+		 * on link2 since it will fail to match the above entry.
+		 */
+
+		.link_mask = 0xF, /* 4 active links required */
+		.links = tgl_3_in_1_sdca_mono,
+		.drv_name = "sof_sdw",
+		.sof_tplg_filename = "sof-tgl-rt711-l0-rt1316-l1-mono-rt714-l3.tplg",
+	},
+
+	{
 		.link_mask = 0x3, /* rt711 on link 0 and 1 rt1308 on link 1 */
 		.links = tgl_hp,
 		.drv_name = "sof_sdw",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/common/soc-intel-quirks.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/common/soc-intel-quirks.h
@@ -9,34 +9,13 @@
 #ifndef _SND_SOC_INTEL_QUIRKS_H
 #define _SND_SOC_INTEL_QUIRKS_H
 
-#if IS_ENABLED(CONFIG_X86)
+#include <linux/platform_data/x86/soc.h>
+
+#if IS_REACHABLE(CONFIG_IOSF_MBI)
 
 #include <linux/dmi.h>
-#include <asm/cpu_device_id.h>
-#include <asm/intel-family.h>
 #include <asm/iosf_mbi.h>
 
-#define SOC_INTEL_IS_CPU(soc, type)				\
-static inline bool soc_intel_is_##soc(void)			\
-{								\
-	static const struct x86_cpu_id soc##_cpu_ids[] = {	\
-		X86_MATCH_INTEL_FAM6_MODEL(type, NULL),		\
-		{}						\
-	};							\
-	const struct x86_cpu_id *id;				\
-								\
-	id = x86_match_cpu(soc##_cpu_ids);			\
-	if (id)							\
-		return true;					\
-	return false;						\
-}
-
-SOC_INTEL_IS_CPU(byt, ATOM_SILVERMONT);
-SOC_INTEL_IS_CPU(cht, ATOM_AIRMONT);
-SOC_INTEL_IS_CPU(apl, ATOM_GOLDMONT);
-SOC_INTEL_IS_CPU(glk, ATOM_GOLDMONT_PLUS);
-SOC_INTEL_IS_CPU(cml, KABYLAKE_L);
-
 static inline bool soc_intel_is_byt_cr(struct platform_device *pdev)
 {
 	/*
@@ -114,30 +93,6 @@
 	return false;
 }
 
-static inline bool soc_intel_is_byt(void)
-{
-	return false;
-}
-
-static inline bool soc_intel_is_cht(void)
-{
-	return false;
-}
-
-static inline bool soc_intel_is_apl(void)
-{
-	return false;
-}
-
-static inline bool soc_intel_is_glk(void)
-{
-	return false;
-}
-
-static inline bool soc_intel_is_cml(void)
-{
-	return false;
-}
 #endif
 
- #endif /* _SND_SOC_INTEL_QUIRKS_H */
+#endif /* _SND_SOC_INTEL_QUIRKS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/keembay/kmb_platform.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/keembay/kmb_platform.c
@@ -815,6 +815,7 @@
 	{ .compatible = "intel,keembay-tdm", .data = &intel_kmb_tdm_dai},
 	{}
 };
+MODULE_DEVICE_TABLE(of, kmb_plat_of_match);
 
 static int kmb_plat_dai_probe(struct platform_device *pdev)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/skylake/skl-nhlt.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/skylake/skl-nhlt.c
@@ -201,7 +201,6 @@
 	struct nhlt_fmt_cfg *fmt_cfg;
 	struct wav_fmt_ext *wav_fmt;
 	unsigned long rate;
-	bool present = false;
 	int rate_index = 0;
 	u16 channels, bps;
 	u8 clk_src;
@@ -214,9 +213,12 @@
 	if (fmt->fmt_count == 0)
 		return;
 
+	fmt_cfg = (struct nhlt_fmt_cfg *)fmt->fmt_config;
 	for (i = 0; i < fmt->fmt_count; i++) {
-		fmt_cfg = &fmt->fmt_config[i];
-		wav_fmt = &fmt_cfg->fmt_ext;
+		struct nhlt_fmt_cfg *saved_fmt_cfg = fmt_cfg;
+		bool present = false;
+
+		wav_fmt = &saved_fmt_cfg->fmt_ext;
 
 		channels = wav_fmt->fmt.channels;
 		bps = wav_fmt->fmt.bits_per_sample;
@@ -234,12 +236,18 @@
 		 * derive the rate.
 		 */
 		for (j = i; j < fmt->fmt_count; j++) {
-			fmt_cfg = &fmt->fmt_config[j];
-			wav_fmt = &fmt_cfg->fmt_ext;
+			struct nhlt_fmt_cfg *tmp_fmt_cfg = fmt_cfg;
+
+			wav_fmt = &tmp_fmt_cfg->fmt_ext;
 			if ((fs == wav_fmt->fmt.samples_per_sec) &&
-			   (bps == wav_fmt->fmt.bits_per_sample))
+			   (bps == wav_fmt->fmt.bits_per_sample)) {
 				channels = max_t(u16, channels,
 						wav_fmt->fmt.channels);
+				saved_fmt_cfg = tmp_fmt_cfg;
+			}
+			/* Move to the next nhlt_fmt_cfg */
+			tmp_fmt_cfg = (struct nhlt_fmt_cfg *)(tmp_fmt_cfg->config.caps +
+							      tmp_fmt_cfg->config.size);
 		}
 
 		rate = channels * bps * fs;
@@ -255,8 +263,11 @@
 
 		/* Fill rate and parent for sclk/sclkfs */
 		if (!present) {
+			struct nhlt_fmt_cfg *first_fmt_cfg;
+
+			first_fmt_cfg = (struct nhlt_fmt_cfg *)fmt->fmt_config;
 			i2s_config_ext = (struct skl_i2s_config_blob_ext *)
-						fmt->fmt_config[0].config.caps;
+						first_fmt_cfg->config.caps;
 
 			/* MCLK Divider Source Select */
 			if (is_legacy_blob(i2s_config_ext->hdr.sig)) {
@@ -270,6 +281,9 @@
 
 			parent = skl_get_parent_clk(clk_src);
 
+			/* Move to the next nhlt_fmt_cfg */
+			fmt_cfg = (struct nhlt_fmt_cfg *)(fmt_cfg->config.caps +
+							  fmt_cfg->config.size);
 			/*
 			 * Do not copy the config data if there is no parent
 			 * clock available for this clock source select
@@ -278,9 +292,9 @@
 				continue;
 
 			sclk[id].rate_cfg[rate_index].rate = rate;
-			sclk[id].rate_cfg[rate_index].config = fmt_cfg;
+			sclk[id].rate_cfg[rate_index].config = saved_fmt_cfg;
 			sclkfs[id].rate_cfg[rate_index].rate = rate;
-			sclkfs[id].rate_cfg[rate_index].config = fmt_cfg;
+			sclkfs[id].rate_cfg[rate_index].config = saved_fmt_cfg;
 			sclk[id].parent_name = parent->name;
 			sclkfs[id].parent_name = parent->name;
 
@@ -294,13 +308,13 @@
 {
 	struct skl_i2s_config_blob_ext *i2s_config_ext;
 	struct skl_i2s_config_blob_legacy *i2s_config;
-	struct nhlt_specific_cfg *fmt_cfg;
+	struct nhlt_fmt_cfg *fmt_cfg;
 	struct skl_clk_parent_src *parent;
 	u32 clkdiv, div_ratio;
 	u8 clk_src;
 
-	fmt_cfg = &fmt->fmt_config[0].config;
-	i2s_config_ext = (struct skl_i2s_config_blob_ext *)fmt_cfg->caps;
+	fmt_cfg = (struct nhlt_fmt_cfg *)fmt->fmt_config;
+	i2s_config_ext = (struct skl_i2s_config_blob_ext *)fmt_cfg->config.caps;
 
 	/* MCLK Divider Source Select and divider */
 	if (is_legacy_blob(i2s_config_ext->hdr.sig)) {
@@ -329,7 +343,7 @@
 		return;
 
 	mclk[id].rate_cfg[0].rate = parent->rate/div_ratio;
-	mclk[id].rate_cfg[0].config = &fmt->fmt_config[0];
+	mclk[id].rate_cfg[0].config = fmt_cfg;
 	mclk[id].parent_name = parent->name;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/skylake/skl-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/skylake/skl-pcm.c
@@ -251,8 +251,10 @@
 	snd_pcm_set_sync(substream);
 
 	mconfig = skl_tplg_fe_get_cpr_module(dai, substream->stream);
-	if (!mconfig)
+	if (!mconfig) {
+		kfree(dma_params);
 		return -EINVAL;
+	}
 
 	skl_tplg_d0i3_get(skl, mconfig->d0i3_caps);
 
@@ -562,11 +564,8 @@
 
 	stream_tag = hdac_stream(link_dev)->stream_tag;
 
-	/* set the stream tag in the codec dai dma params  */
-	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-		snd_soc_dai_set_tdm_slot(codec_dai, stream_tag, 0, 0, 0);
-	else
-		snd_soc_dai_set_tdm_slot(codec_dai, 0, stream_tag, 0, 0);
+	/* set the hdac_stream in the codec dai */
+	snd_soc_dai_set_stream(codec_dai, hdac_stream(link_dev), substream->stream);
 
 	p_params.s_fmt = snd_pcm_format_width(params_format(params));
 	p_params.ch = params_channels(params);
@@ -1251,7 +1250,6 @@
 		snd_pcm_gettime(substream->runtime, system_ts);
 
 		nsec = timecounter_read(&hstr->tc);
-		nsec = div_u64(nsec, 3); /* can be optimized */
 		if (audio_tstamp_config->report_delay)
 			nsec = skl_adjust_codec_delay(substream, nsec);
 
@@ -1469,6 +1467,7 @@
 		dais = krealloc(skl->dais, sizeof(skl_fe_dai) +
 				sizeof(skl_platform_dai), GFP_KERNEL);
 		if (!dais) {
+			kfree(skl->dais);
 			ret = -ENOMEM;
 			goto err;
 		}
@@ -1481,8 +1480,10 @@
 
 	ret = devm_snd_soc_register_component(dev, &skl_component,
 					 skl->dais, num_dais);
-	if (ret)
+	if (ret) {
+		kfree(skl->dais);
 		dev_err(dev, "soc component registration failed %d\n", ret);
+	}
 err:
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/skylake/skl-sst-ipc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/skylake/skl-sst-ipc.c
@@ -1003,8 +1003,10 @@
 
 	reply.size = (reply.header >> 32) & IPC_DATA_OFFSET_SZ_MASK;
 	buf = krealloc(reply.data, reply.size, GFP_KERNEL);
-	if (!buf)
+	if (!buf) {
+		kfree(reply.data);
 		return -ENOMEM;
+	}
 	*payload = buf;
 	*bytes = reply.size;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/skylake/skl-sst-utils.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/skylake/skl-sst-utils.c
@@ -299,6 +299,7 @@
 		module->instance_id = devm_kzalloc(ctx->dev, size, GFP_KERNEL);
 		if (!module->instance_id) {
 			ret = -ENOMEM;
+			kfree(module);
 			goto free_uuid_list;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/intel/skylake/skl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/intel/skylake/skl.c
@@ -439,7 +439,7 @@
 
 	skl->init_done = 0; /* to be sure */
 
-	snd_hdac_ext_stop_streams(bus);
+	snd_hdac_stop_streams_and_chip(bus);
 
 	if (bus->irq >= 0)
 		free_irq(bus->irq, (void *)bus);
@@ -1096,7 +1096,10 @@
 	if (!skl->init_done)
 		return;
 
-	snd_hdac_ext_stop_streams(bus);
+	snd_hdac_stop_streams(bus);
+	snd_hdac_ext_bus_link_power_down_all(bus);
+	skl_dsp_sleep(skl->dsp);
+
 	list_for_each_entry(s, &bus->stream_list, list) {
 		stream = stream_to_hdac_ext_stream(s);
 		snd_hdac_ext_stream_decouple(bus, stream, false);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/jz4740/jz4740-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/jz4740/jz4740-i2s.c
@@ -56,7 +56,8 @@
 #define JZ_AIC_CTRL_MONO_TO_STEREO BIT(11)
 #define JZ_AIC_CTRL_SWITCH_ENDIANNESS BIT(10)
 #define JZ_AIC_CTRL_SIGNED_TO_UNSIGNED BIT(9)
-#define JZ_AIC_CTRL_FLUSH		BIT(8)
+#define JZ_AIC_CTRL_TFLUSH		BIT(8)
+#define JZ_AIC_CTRL_RFLUSH		BIT(7)
 #define JZ_AIC_CTRL_ENABLE_ROR_INT BIT(6)
 #define JZ_AIC_CTRL_ENABLE_TUR_INT BIT(5)
 #define JZ_AIC_CTRL_ENABLE_RFS_INT BIT(4)
@@ -91,6 +92,8 @@
 struct i2s_soc_info {
 	enum jz47xx_i2s_version version;
 	struct snd_soc_dai_driver *dai;
+
+	bool shared_fifo_flush;
 };
 
 struct jz4740_i2s {
@@ -119,19 +122,44 @@
 	writel(value, i2s->base + reg);
 }
 
+static inline void jz4740_i2s_set_bits(const struct jz4740_i2s *i2s,
+	unsigned int reg, uint32_t bits)
+{
+	uint32_t value = jz4740_i2s_read(i2s, reg);
+	value |= bits;
+	jz4740_i2s_write(i2s, reg, value);
+}
+
 static int jz4740_i2s_startup(struct snd_pcm_substream *substream,
 	struct snd_soc_dai *dai)
 {
 	struct jz4740_i2s *i2s = snd_soc_dai_get_drvdata(dai);
-	uint32_t conf, ctrl;
+	uint32_t conf;
 	int ret;
 
+	/*
+	 * When we can flush FIFOs independently, only flush the FIFO
+	 * that is starting up. We can do this when the DAI is active
+	 * because it does not disturb other active substreams.
+	 */
+	if (!i2s->soc_info->shared_fifo_flush) {
+		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+			jz4740_i2s_set_bits(i2s, JZ_REG_AIC_CTRL, JZ_AIC_CTRL_TFLUSH);
+		else
+			jz4740_i2s_set_bits(i2s, JZ_REG_AIC_CTRL, JZ_AIC_CTRL_RFLUSH);
+	}
+
 	if (snd_soc_dai_active(dai))
 		return 0;
 
-	ctrl = jz4740_i2s_read(i2s, JZ_REG_AIC_CTRL);
-	ctrl |= JZ_AIC_CTRL_FLUSH;
-	jz4740_i2s_write(i2s, JZ_REG_AIC_CTRL, ctrl);
+	/*
+	 * When there is a shared flush bit for both FIFOs, the TFLUSH
+	 * bit flushes both FIFOs. Flushing while the DAI is active would
+	 * cause FIFO underruns in other active substreams so we have to
+	 * guard this behind the snd_soc_dai_active() check.
+	 */
+	if (i2s->soc_info->shared_fifo_flush)
+		jz4740_i2s_set_bits(i2s, JZ_REG_AIC_CTRL, JZ_AIC_CTRL_TFLUSH);
 
 	ret = clk_prepare_enable(i2s->clk_i2s);
 	if (ret)
@@ -462,6 +490,7 @@
 static const struct i2s_soc_info jz4740_i2s_soc_info = {
 	.version = JZ_I2S_JZ4740,
 	.dai = &jz4740_i2s_dai,
+	.shared_fifo_flush = true,
 };
 
 static const struct i2s_soc_info jz4760_i2s_soc_info = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/kirkwood/kirkwood-dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/kirkwood/kirkwood-dma.c
@@ -86,7 +86,7 @@
 
 	/* try to find matching cs for current dma address */
 	for (i = 0; i < dram->num_cs; i++) {
-		const struct mbus_dram_window *cs = dram->cs + i;
+		const struct mbus_dram_window *cs = &dram->cs[i];
 		if ((cs->base & 0xffff0000) < (dma & 0xffff0000)) {
 			writel(cs->base & 0xffff0000,
 				base + KIRKWOOD_AUDIO_WIN_BASE_REG(win));
@@ -182,6 +182,9 @@
 	const struct mbus_dram_target_info *dram = mv_mbus_dram_info();
 	unsigned long addr = substream->runtime->dma_addr;
 
+	if (!dram)
+		return 0;
+
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
 		kirkwood_dma_conf_mbus_windows(priv->io,
 			KIRKWOOD_PLAYBACK_WIN, addr, dram);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/common/mtk-afe-platform-driver.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/common/mtk-afe-platform-driver.c
@@ -120,8 +120,8 @@
 	struct mtk_base_afe *afe = snd_soc_component_get_drvdata(component);
 
 	size = afe->mtk_afe_hardware->buffer_bytes_max;
-	snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV,
-				       afe->dev, size, size);
+	snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, afe->dev, 0, size);
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(mtk_afe_pcm_new);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/common/mtk-btcvsd.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/common/mtk-btcvsd.c
@@ -1038,11 +1038,9 @@
 	struct mtk_btcvsd_snd *bt = snd_soc_component_get_drvdata(component);
 
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-		mtk_btcvsd_snd_write(bt, buf, count);
+		return mtk_btcvsd_snd_write(bt, buf, count);
 	else
-		mtk_btcvsd_snd_read(bt, buf, count);
-
-	return 0;
+		return mtk_btcvsd_snd_read(bt, buf, count);
 }
 
 /* kcontrol */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt2701/mt2701-wm8960.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt2701/mt2701-wm8960.c
@@ -129,7 +129,8 @@
 	if (!codec_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_platform_node;
 	}
 	for_each_card_prelinks(card, i, dai_link) {
 		if (dai_link->codecs->name)
@@ -140,7 +141,7 @@
 	ret = snd_soc_of_parse_audio_routing(card, "audio-routing");
 	if (ret) {
 		dev_err(&pdev->dev, "failed to parse audio-routing: %d\n", ret);
-		return ret;
+		goto put_codec_node;
 	}
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
@@ -148,6 +149,10 @@
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
 
+put_codec_node:
+	of_node_put(codec_node);
+put_platform_node:
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt6797/mt6797-mt6351.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt6797/mt6797-mt6351.c
@@ -217,7 +217,8 @@
 	if (!codec_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_platform_node;
 	}
 	for_each_card_prelinks(card, i, dai_link) {
 		if (dai_link->codecs->name)
@@ -230,6 +231,9 @@
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
 
+	of_node_put(codec_node);
+put_platform_node:
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8173/mt8173-afe-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8173/mt8173-afe-pcm.c
@@ -1054,6 +1054,7 @@
 	int irq_id;
 	struct mtk_base_afe *afe;
 	struct mt8173_afe_private *afe_priv;
+	struct snd_soc_component *comp_pcm, *comp_hdmi;
 
 	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(33));
 	if (ret)
@@ -1074,12 +1075,6 @@
 	irq_id = platform_get_irq(pdev, 0);
 	if (irq_id <= 0)
 		return irq_id < 0 ? irq_id : -ENXIO;
-	ret = devm_request_irq(afe->dev, irq_id, mt8173_afe_irq_handler,
-			       0, "Afe_ISR_Handle", (void *)afe);
-	if (ret) {
-		dev_err(afe->dev, "could not request_irq\n");
-		return ret;
-	}
 
 	afe->base_addr = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(afe->base_addr))
@@ -1142,23 +1137,62 @@
 	if (ret)
 		goto err_pm_disable;
 
-	ret = devm_snd_soc_register_component(&pdev->dev,
-					 &mt8173_afe_pcm_dai_component,
-					 mt8173_afe_pcm_dais,
-					 ARRAY_SIZE(mt8173_afe_pcm_dais));
+	comp_pcm = devm_kzalloc(&pdev->dev, sizeof(*comp_pcm), GFP_KERNEL);
+	if (!comp_pcm) {
+		ret = -ENOMEM;
+		goto err_pm_disable;
+	}
+
+	ret = snd_soc_component_initialize(comp_pcm,
+					   &mt8173_afe_pcm_dai_component,
+					   &pdev->dev);
 	if (ret)
 		goto err_pm_disable;
 
-	ret = devm_snd_soc_register_component(&pdev->dev,
-					 &mt8173_afe_hdmi_dai_component,
-					 mt8173_afe_hdmi_dais,
-					 ARRAY_SIZE(mt8173_afe_hdmi_dais));
+#ifdef CONFIG_DEBUG_FS
+	comp_pcm->debugfs_prefix = "pcm";
+#endif
+
+	ret = snd_soc_add_component(comp_pcm,
+				    mt8173_afe_pcm_dais,
+				    ARRAY_SIZE(mt8173_afe_pcm_dais));
 	if (ret)
 		goto err_pm_disable;
 
+	comp_hdmi = devm_kzalloc(&pdev->dev, sizeof(*comp_hdmi), GFP_KERNEL);
+	if (!comp_hdmi) {
+		ret = -ENOMEM;
+		goto err_cleanup_components;
+	}
+
+	ret = snd_soc_component_initialize(comp_hdmi,
+					   &mt8173_afe_hdmi_dai_component,
+					   &pdev->dev);
+	if (ret)
+		goto err_cleanup_components;
+
+#ifdef CONFIG_DEBUG_FS
+	comp_hdmi->debugfs_prefix = "hdmi";
+#endif
+
+	ret = snd_soc_add_component(comp_hdmi,
+				    mt8173_afe_hdmi_dais,
+				    ARRAY_SIZE(mt8173_afe_hdmi_dais));
+	if (ret)
+		goto err_cleanup_components;
+
+	ret = devm_request_irq(afe->dev, irq_id, mt8173_afe_irq_handler,
+			       0, "Afe_ISR_Handle", (void *)afe);
+	if (ret) {
+		dev_err(afe->dev, "could not request_irq\n");
+		goto err_cleanup_components;
+	}
+
 	dev_info(&pdev->dev, "MT8173 AFE driver initialized.\n");
 	return 0;
 
+err_cleanup_components:
+	snd_soc_unregister_component(&pdev->dev);
 err_pm_disable:
 	pm_runtime_disable(&pdev->dev);
 	return ret;
@@ -1166,6 +1200,8 @@
 
 static int mt8173_afe_pcm_dev_remove(struct platform_device *pdev)
 {
+	snd_soc_unregister_component(&pdev->dev);
+
 	pm_runtime_disable(&pdev->dev);
 	if (!pm_runtime_status_suspended(&pdev->dev))
 		mt8173_afe_runtime_suspend(&pdev->dev);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8173/mt8173-max98090.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8173/mt8173-max98090.c
@@ -167,7 +167,8 @@
 	if (!codec_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_platform_node;
 	}
 	for_each_card_prelinks(card, i, dai_link) {
 		if (dai_link->codecs->name)
@@ -180,6 +181,11 @@
 	if (ret)
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
+
+	of_node_put(codec_node);
+
+put_platform_node:
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8173/mt8173-rt5650-rt5514.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8173/mt8173-rt5650-rt5514.c
@@ -200,14 +200,16 @@
 	if (!mt8173_rt5650_rt5514_dais[DAI_LINK_CODEC_I2S].codecs[0].of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto out;
 	}
 	mt8173_rt5650_rt5514_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node =
 		of_parse_phandle(pdev->dev.of_node, "mediatek,audio-codec", 1);
 	if (!mt8173_rt5650_rt5514_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto out;
 	}
 	mt8173_rt5650_rt5514_codec_conf[0].dlc.of_node =
 		mt8173_rt5650_rt5514_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node;
@@ -218,6 +220,9 @@
 	if (ret)
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
+
+out:
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8173/mt8173-rt5650-rt5676.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8173/mt8173-rt5650-rt5676.c
@@ -256,14 +256,16 @@
 	if (!mt8173_rt5650_rt5676_dais[DAI_LINK_CODEC_I2S].codecs[0].of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_node;
 	}
 	mt8173_rt5650_rt5676_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node =
 		of_parse_phandle(pdev->dev.of_node, "mediatek,audio-codec", 1);
 	if (!mt8173_rt5650_rt5676_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_node;
 	}
 	mt8173_rt5650_rt5676_codec_conf[0].dlc.of_node =
 		mt8173_rt5650_rt5676_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node;
@@ -276,7 +278,8 @@
 	if (!mt8173_rt5650_rt5676_dais[DAI_LINK_HDMI_I2S].codecs->of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_node;
 	}
 
 	card->dev = &pdev->dev;
@@ -285,6 +288,9 @@
 	if (ret)
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
+
+put_node:
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8173/mt8173-rt5650.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8173/mt8173-rt5650.c
@@ -280,7 +280,8 @@
 	if (!mt8173_rt5650_dais[DAI_LINK_CODEC_I2S].codecs[0].of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_platform_node;
 	}
 	mt8173_rt5650_dais[DAI_LINK_CODEC_I2S].codecs[1].of_node =
 		mt8173_rt5650_dais[DAI_LINK_CODEC_I2S].codecs[0].of_node;
@@ -293,7 +294,7 @@
 			dev_err(&pdev->dev,
 				"%s codec_capture_dai name fail %d\n",
 				__func__, ret);
-			return ret;
+			goto put_platform_node;
 		}
 		mt8173_rt5650_dais[DAI_LINK_CODEC_I2S].codecs[1].dai_name =
 			codec_capture_dai;
@@ -315,7 +316,8 @@
 	if (!mt8173_rt5650_dais[DAI_LINK_HDMI_I2S].codecs->of_node) {
 		dev_err(&pdev->dev,
 			"Property 'audio-codec' missing or invalid\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_platform_node;
 	}
 	card->dev = &pdev->dev;
 
@@ -323,6 +325,9 @@
 	if (ret)
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
+
+put_platform_node:
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8183/mt8183-da7219-max98357.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8183/mt8183-da7219-max98357.c
@@ -685,7 +685,6 @@
 	struct snd_soc_dai_link *dai_link;
 	struct mt8183_da7219_max98357_priv *priv;
 	struct pinctrl *pinctrl;
-	const struct of_device_id *match;
 	int ret, i;
 
 	platform_node = of_parse_phandle(pdev->dev.of_node,
@@ -695,11 +694,9 @@
 		return -EINVAL;
 	}
 
-	match = of_match_device(pdev->dev.driver->of_match_table, &pdev->dev);
-	if (!match || !match->data)
+	card = (struct snd_soc_card *)of_device_get_match_data(&pdev->dev);
+	if (!card)
 		return -EINVAL;
-
-	card = (struct snd_soc_card *)match->data;
 	card->dev = &pdev->dev;
 
 	hdmi_codec = of_parse_phandle(pdev->dev.of_node,
@@ -781,7 +778,11 @@
 		return ret;
 	}
 
-	return devm_snd_soc_register_card(&pdev->dev, card);
+	ret = devm_snd_soc_register_card(&pdev->dev, card);
+
+	of_node_put(platform_node);
+	of_node_put(hdmi_codec);
+	return ret;
 }
 
 #ifdef CONFIG_OF
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8183/mt8183-mt6358-ts3a227-max98357.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8183/mt8183-mt6358-ts3a227-max98357.c
@@ -637,7 +637,6 @@
 	struct device_node *platform_node, *ec_codec, *hdmi_codec;
 	struct snd_soc_dai_link *dai_link;
 	struct mt8183_mt6358_ts3a227_max98357_priv *priv;
-	const struct of_device_id *match;
 	int ret, i;
 
 	platform_node = of_parse_phandle(pdev->dev.of_node,
@@ -647,11 +646,11 @@
 		return -EINVAL;
 	}
 
-	match = of_match_device(pdev->dev.driver->of_match_table, &pdev->dev);
-	if (!match || !match->data)
+	card = (struct snd_soc_card *)of_device_get_match_data(&pdev->dev);
+	if (!card) {
+		of_node_put(platform_node);
 		return -EINVAL;
-
-	card = (struct snd_soc_card *)match->data;
+	}
 	card->dev = &pdev->dev;
 
 	ec_codec = of_parse_phandle(pdev->dev.of_node, "mediatek,ec-codec", 0);
@@ -740,8 +739,10 @@
 	}
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
+	if (!priv) {
+		ret = -ENOMEM;
+		goto out;
+	}
 
 	snd_soc_card_set_drvdata(card, priv);
 
@@ -749,7 +750,8 @@
 	if (IS_ERR(priv->pinctrl)) {
 		dev_err(&pdev->dev, "%s devm_pinctrl_get failed\n",
 			__func__);
-		return PTR_ERR(priv->pinctrl);
+		ret = PTR_ERR(priv->pinctrl);
+		goto out;
 	}
 
 	for (i = 0; i < PIN_STATE_MAX; i++) {
@@ -780,7 +782,13 @@
 				 __func__, ret);
 	}
 
-	return devm_snd_soc_register_card(&pdev->dev, card);
+	ret = devm_snd_soc_register_card(&pdev->dev, card);
+
+out:
+	of_node_put(platform_node);
+	of_node_put(ec_codec);
+	of_node_put(hdmi_codec);
+	return ret;
 }
 
 #ifdef CONFIG_OF
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8192/mt8192-dai-tdm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8192/mt8192-dai-tdm.c
@@ -566,10 +566,10 @@
 		tdm_con |= 1 << DELAY_DATA_SFT;
 		tdm_con |= get_tdm_lrck_width(format) << LRCK_TDM_WIDTH_SFT;
 	} else if (tdm_priv->tdm_out_mode == TDM_OUT_DSP_A) {
-		tdm_con |= 0 << DELAY_DATA_SFT;
+		tdm_con |= 1 << DELAY_DATA_SFT;
 		tdm_con |= 0 << LRCK_TDM_WIDTH_SFT;
 	} else if (tdm_priv->tdm_out_mode == TDM_OUT_DSP_B) {
-		tdm_con |= 1 << DELAY_DATA_SFT;
+		tdm_con |= 0 << DELAY_DATA_SFT;
 		tdm_con |= 0 << LRCK_TDM_WIDTH_SFT;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8192/mt8192-mt6359-rt1015-rt5682.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8192/mt8192-mt6359-rt1015-rt5682.c
@@ -1106,7 +1106,6 @@
 	struct device_node *platform_node, *hdmi_codec;
 	int ret, i;
 	struct snd_soc_dai_link *dai_link;
-	const struct of_device_id *match;
 	struct mt8192_mt6359_priv *priv;
 
 	platform_node = of_parse_phandle(pdev->dev.of_node,
@@ -1116,11 +1115,11 @@
 		return -EINVAL;
 	}
 
-	match = of_match_device(pdev->dev.driver->of_match_table, &pdev->dev);
-	if (!match || !match->data)
-		return -EINVAL;
-
-	card = (struct snd_soc_card *)match->data;
+	card = (struct snd_soc_card *)of_device_get_match_data(&pdev->dev);
+	if (!card) {
+		ret = -EINVAL;
+		goto put_platform_node;
+	}
 	card->dev = &pdev->dev;
 
 	hdmi_codec = of_parse_phandle(pdev->dev.of_node,
@@ -1162,17 +1161,25 @@
 	}
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
+	if (!priv) {
+		ret = -ENOMEM;
+		goto put_hdmi_codec;
+	}
 	snd_soc_card_set_drvdata(card, priv);
 
 	ret = mt8192_afe_gpio_init(&pdev->dev);
 	if (ret) {
 		dev_err(&pdev->dev, "init gpio error %d\n", ret);
-		return ret;
+		goto put_hdmi_codec;
 	}
 
-	return devm_snd_soc_register_card(&pdev->dev, card);
+	ret = devm_snd_soc_register_card(&pdev->dev, card);
+
+put_hdmi_codec:
+	of_node_put(hdmi_codec);
+put_platform_node:
+	of_node_put(platform_node);
+	return ret;
 }
 
 #ifdef CONFIG_OF
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-afe-clk.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-afe-clk.c
@@ -136,11 +136,6 @@
 	return 0;
 }
 
-void mt8195_afe_deinit_clock(struct mtk_base_afe *afe)
-{
-	mt8195_audsys_clk_unregister(afe);
-}
-
 int mt8195_afe_enable_clk(struct mtk_base_afe *afe, struct clk *clk)
 {
 	int ret;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-afe-clk.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-afe-clk.h
@@ -90,7 +90,6 @@
 int mt8195_afe_get_mclk_source_rate(struct mtk_base_afe *afe, int apll);
 int mt8195_afe_get_default_mclk_source_by_rate(int rate);
 int mt8195_afe_init_clock(struct mtk_base_afe *afe);
-void mt8195_afe_deinit_clock(struct mtk_base_afe *afe);
 int mt8195_afe_enable_clk(struct mtk_base_afe *afe, struct clk *clk);
 void mt8195_afe_disable_clk(struct mtk_base_afe *afe, struct clk *clk);
 int mt8195_afe_prepare_clk(struct mtk_base_afe *afe, struct clk *clk);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-afe-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-afe-pcm.c
@@ -3028,7 +3028,7 @@
 
 static const struct reg_sequence mt8195_cg_patch[] = {
 	{ AUDIO_TOP_CON0, 0xfffffffb },
-	{ AUDIO_TOP_CON1, 0xfffffffa },
+	{ AUDIO_TOP_CON1, 0xfffffff8 },
 };
 
 static int mt8195_afe_init_registers(struct mtk_base_afe *afe)
@@ -3237,18 +3237,13 @@
 	return ret;
 }
 
-static int mt8195_afe_pcm_dev_remove(struct platform_device *pdev)
+static void mt8195_afe_pcm_dev_remove(struct platform_device *pdev)
 {
-	struct mtk_base_afe *afe = platform_get_drvdata(pdev);
-
 	snd_soc_unregister_component(&pdev->dev);
 
 	pm_runtime_disable(&pdev->dev);
 	if (!pm_runtime_status_suspended(&pdev->dev))
 		mt8195_afe_runtime_suspend(&pdev->dev);
-
-	mt8195_afe_deinit_clock(afe);
-	return 0;
 }
 
 static const struct of_device_id mt8195_afe_pcm_dt_match[] = {
@@ -3271,7 +3266,7 @@
 #endif
 	},
 	.probe = mt8195_afe_pcm_dev_probe,
-	.remove = mt8195_afe_pcm_dev_remove,
+	.remove_new = mt8195_afe_pcm_dev_remove,
 };
 
 module_platform_driver(mt8195_afe_pcm_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-audsys-clk.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-audsys-clk.c
@@ -148,6 +148,29 @@
 	GATE_AUD6(CLK_AUD_GASRC19, "aud_gasrc19", "asm_h_sel", 19),
 };
 
+static void mt8195_audsys_clk_unregister(void *data)
+{
+	struct mtk_base_afe *afe = data;
+	struct mt8195_afe_private *afe_priv = afe->platform_priv;
+	struct clk *clk;
+	struct clk_lookup *cl;
+	int i;
+
+	if (!afe_priv)
+		return;
+
+	for (i = 0; i < CLK_AUD_NR_CLK; i++) {
+		cl = afe_priv->lookup[i];
+		if (!cl)
+			continue;
+
+		clk = cl->clk;
+		clk_unregister_gate(clk);
+
+		clkdev_drop(cl);
+	}
+}
+
 int mt8195_audsys_clk_register(struct mtk_base_afe *afe)
 {
 	struct mt8195_afe_private *afe_priv = afe->platform_priv;
@@ -188,27 +211,5 @@
 		afe_priv->lookup[i] = cl;
 	}
 
-	return 0;
-}
-
-void mt8195_audsys_clk_unregister(struct mtk_base_afe *afe)
-{
-	struct mt8195_afe_private *afe_priv = afe->platform_priv;
-	struct clk *clk;
-	struct clk_lookup *cl;
-	int i;
-
-	if (!afe_priv)
-		return;
-
-	for (i = 0; i < CLK_AUD_NR_CLK; i++) {
-		cl = afe_priv->lookup[i];
-		if (!cl)
-			continue;
-
-		clk = cl->clk;
-		clk_unregister_gate(clk);
-
-		clkdev_drop(cl);
-	}
+	return devm_add_action_or_reset(afe->dev, mt8195_audsys_clk_unregister, afe);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-audsys-clk.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-audsys-clk.h
@@ -10,6 +10,5 @@
 #define _MT8195_AUDSYS_CLK_H_
 
 int mt8195_audsys_clk_register(struct mtk_base_afe *afe);
-void mt8195_audsys_clk_unregister(struct mtk_base_afe *afe);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-dai-etdm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-dai-etdm.c
@@ -2567,6 +2567,9 @@
 
 	/* etdm in only */
 	for (i = 0; i < 2; i++) {
+		dai_id = ETDM_TO_DAI_ID(i);
+		etdm_data = afe_priv->dai_priv[dai_id];
+
 		ret = snprintf(prop, sizeof(prop),
 			       "mediatek,%s-chn-disabled",
 			       of_afe_etdms[i].name);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-dai-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-dai-pcm.c
@@ -80,8 +80,15 @@
 			   mtk_dai_pcm_o001_mix,
 			   ARRAY_SIZE(mtk_dai_pcm_o001_mix)),
 
+	SND_SOC_DAPM_SUPPLY("PCM_EN", PCM_INTF_CON1,
+			    PCM_INTF_CON1_PCM_EN_SHIFT, 0, NULL, 0),
+
 	SND_SOC_DAPM_INPUT("PCM1_INPUT"),
 	SND_SOC_DAPM_OUTPUT("PCM1_OUTPUT"),
+
+	SND_SOC_DAPM_CLOCK_SUPPLY("aud_asrc11"),
+	SND_SOC_DAPM_CLOCK_SUPPLY("aud_asrc12"),
+	SND_SOC_DAPM_CLOCK_SUPPLY("aud_pcmif"),
 };
 
 static const struct snd_soc_dapm_route mtk_dai_pcm_routes[] = {
@@ -97,22 +104,18 @@
 	{"PCM1 Playback", NULL, "O000"},
 	{"PCM1 Playback", NULL, "O001"},
 
+	{"PCM1 Playback", NULL, "PCM_EN"},
+	{"PCM1 Playback", NULL, "aud_asrc12"},
+	{"PCM1 Playback", NULL, "aud_pcmif"},
+
+	{"PCM1 Capture", NULL, "PCM_EN"},
+	{"PCM1 Capture", NULL, "aud_asrc11"},
+	{"PCM1 Capture", NULL, "aud_pcmif"},
+
 	{"PCM1_OUTPUT", NULL, "PCM1 Playback"},
 	{"PCM1 Capture", NULL, "PCM1_INPUT"},
 };
 
-static void mtk_dai_pcm_enable(struct mtk_base_afe *afe)
-{
-	regmap_update_bits(afe->regmap, PCM_INTF_CON1,
-			   PCM_INTF_CON1_PCM_EN, PCM_INTF_CON1_PCM_EN);
-}
-
-static void mtk_dai_pcm_disable(struct mtk_base_afe *afe)
-{
-	regmap_update_bits(afe->regmap, PCM_INTF_CON1,
-			   PCM_INTF_CON1_PCM_EN, 0x0);
-}
-
 static int mtk_dai_pcm_configure(struct snd_pcm_substream *substream,
 				 struct snd_soc_dai *dai)
 {
@@ -207,54 +210,22 @@
 }
 
 /* dai ops */
-static int mtk_dai_pcm_startup(struct snd_pcm_substream *substream,
-			       struct snd_soc_dai *dai)
-{
-	struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai);
-	struct mt8195_afe_private *afe_priv = afe->platform_priv;
-
-	if (dai->component->active)
-		return 0;
-
-	mt8195_afe_enable_clk(afe, afe_priv->clk[MT8195_CLK_AUD_ASRC11]);
-	mt8195_afe_enable_clk(afe, afe_priv->clk[MT8195_CLK_AUD_ASRC12]);
-	mt8195_afe_enable_clk(afe, afe_priv->clk[MT8195_CLK_AUD_PCMIF]);
-
-	return 0;
-}
-
-static void mtk_dai_pcm_shutdown(struct snd_pcm_substream *substream,
-				 struct snd_soc_dai *dai)
-{
-	struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai);
-	struct mt8195_afe_private *afe_priv = afe->platform_priv;
-
-	if (dai->component->active)
-		return;
-
-	mtk_dai_pcm_disable(afe);
-
-	mt8195_afe_disable_clk(afe, afe_priv->clk[MT8195_CLK_AUD_PCMIF]);
-	mt8195_afe_disable_clk(afe, afe_priv->clk[MT8195_CLK_AUD_ASRC12]);
-	mt8195_afe_disable_clk(afe, afe_priv->clk[MT8195_CLK_AUD_ASRC11]);
-}
-
 static int mtk_dai_pcm_prepare(struct snd_pcm_substream *substream,
 			       struct snd_soc_dai *dai)
 {
-	struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai);
-	int ret = 0;
+	int ret;
 
-	if (snd_soc_dai_stream_active(dai, SNDRV_PCM_STREAM_PLAYBACK) &&
-	    snd_soc_dai_stream_active(dai, SNDRV_PCM_STREAM_CAPTURE))
+	dev_dbg(dai->dev, "%s(), id %d, stream %d, widget active p %d, c %d\n",
+		__func__, dai->id, substream->stream,
+		dai->playback_widget->active, dai->capture_widget->active);
+
+	if (dai->playback_widget->active || dai->capture_widget->active)
 		return 0;
 
 	ret = mtk_dai_pcm_configure(substream, dai);
 	if (ret)
 		return ret;
 
-	mtk_dai_pcm_enable(afe);
-
 	return 0;
 }
 
@@ -316,8 +287,6 @@
 }
 
 static const struct snd_soc_dai_ops mtk_dai_pcm_ops = {
-	.startup	= mtk_dai_pcm_startup,
-	.shutdown	= mtk_dai_pcm_shutdown,
 	.prepare	= mtk_dai_pcm_prepare,
 	.set_fmt	= mtk_dai_pcm_set_fmt,
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c
@@ -1040,8 +1040,10 @@
 	}
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
+	if (!priv) {
+		of_node_put(platform_node);
 		return -ENOMEM;
+	}
 
 	snd_soc_card_set_drvdata(card, priv);
 
@@ -1049,6 +1051,8 @@
 	if (ret)
 		dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n",
 			__func__, ret);
+
+	of_node_put(platform_node);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mediatek/mt8195/mt8195-reg.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mediatek/mt8195/mt8195-reg.h
@@ -2550,6 +2550,7 @@
 #define PCM_INTF_CON1_PCM_FMT(x)       (((x) & 0x3) << 1)
 #define PCM_INTF_CON1_PCM_FMT_MASK     (0x3 << 1)
 #define PCM_INTF_CON1_PCM_EN           BIT(0)
+#define PCM_INTF_CON1_PCM_EN_SHIFT     0
 
 /* PCM_INTF_CON2 */
 #define PCM_INTF_CON2_CLK_DOMAIN_SEL(x)   (((x) & 0x3) << 23)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/Kconfig
@@ -99,6 +99,7 @@
 
 config SND_MESON_CARD_UTILS
 	tristate
+	select SND_DYNAMIC_MINORS
 
 config SND_MESON_CODEC_GLUE
 	tristate
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu-acodec-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu-acodec-ctrl.c
@@ -58,7 +58,7 @@
 
 	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
 
-	return 0;
+	return 1;
 }
 
 static SOC_ENUM_SINGLE_DECL(aiu_acodec_ctrl_mux_enum, AIU_ACODEC_CTRL,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu-codec-ctrl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu-codec-ctrl.c
@@ -57,7 +57,7 @@
 
 	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
 
-	return 0;
+	return 1;
 }
 
 static SOC_ENUM_SINGLE_DECL(aiu_hdmi_ctrl_mux_enum, AIU_HDMI_CLK_DATA_CTRL,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu-encoder-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu-encoder-i2s.c
@@ -18,7 +18,6 @@
 #define AIU_RST_SOFT_I2S_FAST		BIT(0)
 
 #define AIU_I2S_DAC_CFG_MSB_FIRST	BIT(2)
-#define AIU_I2S_MISC_HOLD_EN		BIT(2)
 #define AIU_CLK_CTRL_I2S_DIV_EN		BIT(0)
 #define AIU_CLK_CTRL_I2S_DIV		GENMASK(3, 2)
 #define AIU_CLK_CTRL_AOCLK_INVERT	BIT(6)
@@ -36,37 +35,6 @@
 				      enable ? AIU_CLK_CTRL_I2S_DIV_EN : 0);
 }
 
-static void aiu_encoder_i2s_hold(struct snd_soc_component *component,
-				 bool enable)
-{
-	snd_soc_component_update_bits(component, AIU_I2S_MISC,
-				      AIU_I2S_MISC_HOLD_EN,
-				      enable ? AIU_I2S_MISC_HOLD_EN : 0);
-}
-
-static int aiu_encoder_i2s_trigger(struct snd_pcm_substream *substream, int cmd,
-				   struct snd_soc_dai *dai)
-{
-	struct snd_soc_component *component = dai->component;
-
-	switch (cmd) {
-	case SNDRV_PCM_TRIGGER_START:
-	case SNDRV_PCM_TRIGGER_RESUME:
-	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
-		aiu_encoder_i2s_hold(component, false);
-		return 0;
-
-	case SNDRV_PCM_TRIGGER_STOP:
-	case SNDRV_PCM_TRIGGER_SUSPEND:
-	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
-		aiu_encoder_i2s_hold(component, true);
-		return 0;
-
-	default:
-		return -EINVAL;
-	}
-}
-
 static int aiu_encoder_i2s_setup_desc(struct snd_soc_component *component,
 				      struct snd_pcm_hw_params *params)
 {
@@ -353,7 +321,6 @@
 }
 
 const struct snd_soc_dai_ops aiu_encoder_i2s_dai_ops = {
-	.trigger	= aiu_encoder_i2s_trigger,
 	.hw_params	= aiu_encoder_i2s_hw_params,
 	.hw_free	= aiu_encoder_i2s_hw_free,
 	.set_fmt	= aiu_encoder_i2s_set_fmt,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu-fifo-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu-fifo-i2s.c
@@ -20,6 +20,8 @@
 #define AIU_MEM_I2S_CONTROL_MODE_16BIT	BIT(6)
 #define AIU_MEM_I2S_BUF_CNTL_INIT	BIT(0)
 #define AIU_RST_SOFT_I2S_FAST		BIT(0)
+#define AIU_I2S_MISC_HOLD_EN		BIT(2)
+#define AIU_I2S_MISC_FORCE_LEFT_RIGHT	BIT(4)
 
 #define AIU_FIFO_I2S_BLOCK		256
 
@@ -90,6 +92,10 @@
 	unsigned int val;
 	int ret;
 
+	snd_soc_component_update_bits(component, AIU_I2S_MISC,
+				      AIU_I2S_MISC_HOLD_EN,
+				      AIU_I2S_MISC_HOLD_EN);
+
 	ret = aiu_fifo_hw_params(substream, params, dai);
 	if (ret)
 		return ret;
@@ -117,6 +123,19 @@
 	snd_soc_component_update_bits(component, AIU_MEM_I2S_MASKS,
 				      AIU_MEM_I2S_MASKS_IRQ_BLOCK, val);
 
+	/*
+	 * Most (all?) supported SoCs have this bit set by default. The vendor
+	 * driver however sets it manually (depending on the version either
+	 * while un-setting AIU_I2S_MISC_HOLD_EN or right before that). Follow
+	 * the same approach for consistency with the vendor driver.
+	 */
+	snd_soc_component_update_bits(component, AIU_I2S_MISC,
+				      AIU_I2S_MISC_FORCE_LEFT_RIGHT,
+				      AIU_I2S_MISC_FORCE_LEFT_RIGHT);
+
+	snd_soc_component_update_bits(component, AIU_I2S_MISC,
+				      AIU_I2S_MISC_HOLD_EN, 0);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu-fifo.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu-fifo.c
@@ -5,6 +5,7 @@
 
 #include <linux/bitfield.h>
 #include <linux/clk.h>
+#include <linux/dma-mapping.h>
 #include <sound/pcm_params.h>
 #include <sound/soc.h>
 #include <sound/soc-dai.h>
@@ -179,6 +180,11 @@
 	struct snd_card *card = rtd->card->snd_card;
 	struct aiu_fifo *fifo = dai->playback_dma_data;
 	size_t size = fifo->pcm->buffer_bytes_max;
+	int ret;
+
+	ret = dma_coerce_mask_and_coherent(card->dev, DMA_BIT_MASK(32));
+	if (ret)
+		return ret;
 
 	snd_pcm_set_managed_buffer_all(rtd->pcm, SNDRV_DMA_TYPE_DEV,
 				       card->dev, size, size);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu.c
@@ -215,49 +215,27 @@
 static int aiu_clk_get(struct device *dev)
 {
 	struct aiu *aiu = dev_get_drvdata(dev);
+	struct clk *pclk;
 	int ret;
 
-	aiu->pclk = devm_clk_get(dev, "pclk");
-	if (IS_ERR(aiu->pclk)) {
-		if (PTR_ERR(aiu->pclk) != -EPROBE_DEFER)
-			dev_err(dev, "Can't get the aiu pclk\n");
-		return PTR_ERR(aiu->pclk);
-	}
+	pclk = devm_clk_get_enabled(dev, "pclk");
+	if (IS_ERR(pclk))
+		return dev_err_probe(dev, PTR_ERR(pclk), "Can't get the aiu pclk\n");
 
 	aiu->spdif_mclk = devm_clk_get(dev, "spdif_mclk");
-	if (IS_ERR(aiu->spdif_mclk)) {
-		if (PTR_ERR(aiu->spdif_mclk) != -EPROBE_DEFER)
-			dev_err(dev, "Can't get the aiu spdif master clock\n");
-		return PTR_ERR(aiu->spdif_mclk);
-	}
+	if (IS_ERR(aiu->spdif_mclk))
+		return dev_err_probe(dev, PTR_ERR(aiu->spdif_mclk),
+				     "Can't get the aiu spdif master clock\n");
 
 	ret = aiu_clk_bulk_get(dev, aiu_i2s_ids, ARRAY_SIZE(aiu_i2s_ids),
 			       &aiu->i2s);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "Can't get the i2s clocks\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Can't get the i2s clocks\n");
 
 	ret = aiu_clk_bulk_get(dev, aiu_spdif_ids, ARRAY_SIZE(aiu_spdif_ids),
 			       &aiu->spdif);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "Can't get the spdif clocks\n");
-		return ret;
-	}
-
-	ret = clk_prepare_enable(aiu->pclk);
-	if (ret) {
-		dev_err(dev, "peripheral clock enable failed\n");
-		return ret;
-	}
-
-	ret = devm_add_action_or_reset(dev,
-				       (void(*)(void *))clk_disable_unprepare,
-				       aiu->pclk);
 	if (ret)
-		dev_err(dev, "failed to add reset action on pclk");
+		return dev_err_probe(dev, ret, "Can't get the spdif clocks\n");
 
 	return ret;
 }
@@ -281,11 +259,8 @@
 	platform_set_drvdata(pdev, aiu);
 
 	ret = device_reset(dev);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "Failed to reset device\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to reset device\n");
 
 	regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(regs))
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/aiu.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/aiu.h
@@ -33,7 +33,6 @@
 };
 
 struct aiu {
-	struct clk *pclk;
 	struct clk *spdif_mclk;
 	struct aiu_interface i2s;
 	struct aiu_interface spdif;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-card.c
@@ -104,7 +104,7 @@
 				     int *index)
 {
 	struct meson_card *priv = snd_soc_card_get_drvdata(card);
-	struct snd_soc_dai_link *pad = &card->dai_link[*index];
+	struct snd_soc_dai_link *pad;
 	struct snd_soc_dai_link *lb;
 	struct snd_soc_dai_link_component *dlc;
 	int ret;
@@ -114,6 +114,7 @@
 	if (ret)
 		return ret;
 
+	pad = &card->dai_link[*index];
 	lb = &card->dai_link[*index + 1];
 
 	lb->name = devm_kasprintf(card->dev, GFP_KERNEL, "%s-lb", pad->name);
@@ -320,6 +321,7 @@
 
 	dai_link->cpus = cpu;
 	dai_link->num_cpus = 1;
+	dai_link->nonatomic = true;
 
 	ret = meson_card_parse_dai(card, np, &dai_link->cpus->of_node,
 				   &dai_link->cpus->dai_name);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-fifo.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-fifo.c
@@ -3,6 +3,7 @@
 // Copyright (c) 2018 BayLibre, SAS.
 // Author: Jerome Brunet <jbrunet@baylibre.com>
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
@@ -145,8 +146,8 @@
 	/* Enable irq if necessary  */
 	irq_en = runtime->no_period_wakeup ? 0 : FIFO_INT_COUNT_REPEAT;
 	regmap_update_bits(fifo->map, FIFO_CTRL0,
-			   CTRL0_INT_EN(FIFO_INT_COUNT_REPEAT),
-			   CTRL0_INT_EN(irq_en));
+			   CTRL0_INT_EN,
+			   FIELD_PREP(CTRL0_INT_EN, irq_en));
 
 	return 0;
 }
@@ -176,9 +177,9 @@
 {
 	struct axg_fifo *fifo = axg_fifo_data(ss);
 
-	/* Disable the block count irq */
+	/* Disable irqs */
 	regmap_update_bits(fifo->map, FIFO_CTRL0,
-			   CTRL0_INT_EN(FIFO_INT_COUNT_REPEAT), 0);
+			   CTRL0_INT_EN, 0);
 
 	return 0;
 }
@@ -187,13 +188,13 @@
 static void axg_fifo_ack_irq(struct axg_fifo *fifo, u8 mask)
 {
 	regmap_update_bits(fifo->map, FIFO_CTRL1,
-			   CTRL1_INT_CLR(FIFO_INT_MASK),
-			   CTRL1_INT_CLR(mask));
+			   CTRL1_INT_CLR,
+			   FIELD_PREP(CTRL1_INT_CLR, mask));
 
 	/* Clear must also be cleared */
 	regmap_update_bits(fifo->map, FIFO_CTRL1,
-			   CTRL1_INT_CLR(FIFO_INT_MASK),
-			   0);
+			   CTRL1_INT_CLR,
+			   FIELD_PREP(CTRL1_INT_CLR, 0));
 }
 
 static irqreturn_t axg_fifo_pcm_irq_block(int irq, void *dev_id)
@@ -203,18 +204,19 @@
 	unsigned int status;
 
 	regmap_read(fifo->map, FIFO_STATUS1, &status);
+	status = FIELD_GET(STATUS1_INT_STS, status);
+	axg_fifo_ack_irq(fifo, status);
 
-	status = STATUS1_INT_STS(status) & FIFO_INT_MASK;
-	if (status & FIFO_INT_COUNT_REPEAT)
-		snd_pcm_period_elapsed(ss);
-	else
+	if (status & ~FIFO_INT_COUNT_REPEAT)
 		dev_dbg(axg_fifo_dev(ss), "unexpected irq - STS 0x%02x\n",
 			status);
 
-	/* Ack irqs */
-	axg_fifo_ack_irq(fifo, status);
+	if (status & FIFO_INT_COUNT_REPEAT) {
+		snd_pcm_period_elapsed(ss);
+		return IRQ_HANDLED;
+	}
 
-	return IRQ_RETVAL(status);
+	return IRQ_NONE;
 }
 
 int axg_fifo_pcm_open(struct snd_soc_component *component,
@@ -242,8 +244,10 @@
 	if (ret)
 		return ret;
 
-	ret = request_irq(fifo->irq, axg_fifo_pcm_irq_block, 0,
-			  dev_name(dev), ss);
+	/* Use the threaded irq handler only with non-atomic links */
+	ret = request_threaded_irq(fifo->irq, NULL,
+				   axg_fifo_pcm_irq_block,
+				   IRQF_ONESHOT, dev_name(dev), ss);
 	if (ret)
 		return ret;
 
@@ -254,15 +258,15 @@
 
 	/* Setup status2 so it reports the memory pointer */
 	regmap_update_bits(fifo->map, FIFO_CTRL1,
-			   CTRL1_STATUS2_SEL_MASK,
-			   CTRL1_STATUS2_SEL(STATUS2_SEL_DDR_READ));
+			   CTRL1_STATUS2_SEL,
+			   FIELD_PREP(CTRL1_STATUS2_SEL, STATUS2_SEL_DDR_READ));
 
 	/* Make sure the dma is initially disabled */
 	__dma_enable(fifo, false);
 
 	/* Disable irqs until params are ready */
 	regmap_update_bits(fifo->map, FIFO_CTRL0,
-			   CTRL0_INT_EN(FIFO_INT_MASK), 0);
+			   CTRL0_INT_EN, 0);
 
 	/* Clear any pending interrupt */
 	axg_fifo_ack_irq(fifo, FIFO_INT_MASK);
@@ -351,20 +355,12 @@
 	}
 
 	fifo->pclk = devm_clk_get(dev, NULL);
-	if (IS_ERR(fifo->pclk)) {
-		if (PTR_ERR(fifo->pclk) != -EPROBE_DEFER)
-			dev_err(dev, "failed to get pclk: %ld\n",
-				PTR_ERR(fifo->pclk));
-		return PTR_ERR(fifo->pclk);
-	}
+	if (IS_ERR(fifo->pclk))
+		return dev_err_probe(dev, PTR_ERR(fifo->pclk), "failed to get pclk\n");
 
 	fifo->arb = devm_reset_control_get_exclusive(dev, NULL);
-	if (IS_ERR(fifo->arb)) {
-		if (PTR_ERR(fifo->arb) != -EPROBE_DEFER)
-			dev_err(dev, "failed to get arb reset: %ld\n",
-				PTR_ERR(fifo->arb));
-		return PTR_ERR(fifo->arb);
-	}
+	if (IS_ERR(fifo->arb))
+		return dev_err_probe(dev, PTR_ERR(fifo->arb), "failed to get arb reset\n");
 
 	fifo->irq = of_irq_get(dev->of_node, 0);
 	if (fifo->irq <= 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-fifo.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-fifo.h
@@ -42,21 +42,19 @@
 
 #define FIFO_CTRL0			0x00
 #define  CTRL0_DMA_EN			BIT(31)
-#define  CTRL0_INT_EN(x)		((x) << 16)
+#define  CTRL0_INT_EN			GENMASK(23, 16)
 #define  CTRL0_SEL_MASK			GENMASK(2, 0)
 #define  CTRL0_SEL_SHIFT		0
 #define FIFO_CTRL1			0x04
-#define  CTRL1_INT_CLR(x)		((x) << 0)
-#define  CTRL1_STATUS2_SEL_MASK		GENMASK(11, 8)
-#define  CTRL1_STATUS2_SEL(x)		((x) << 8)
+#define  CTRL1_INT_CLR			GENMASK(7, 0)
+#define  CTRL1_STATUS2_SEL		GENMASK(11, 8)
 #define   STATUS2_SEL_DDR_READ		0
-#define  CTRL1_FRDDR_DEPTH_MASK		GENMASK(31, 24)
-#define  CTRL1_FRDDR_DEPTH(x)		((x) << 24)
+#define  CTRL1_FRDDR_DEPTH		GENMASK(31, 24)
 #define FIFO_START_ADDR			0x08
 #define FIFO_FINISH_ADDR		0x0c
 #define FIFO_INT_ADDR			0x10
 #define FIFO_STATUS1			0x14
-#define  STATUS1_INT_STS(x)		((x) << 0)
+#define  STATUS1_INT_STS		GENMASK(7, 0)
 #define FIFO_STATUS2			0x18
 #define FIFO_INIT_ADDR			0x24
 #define FIFO_CTRL2			0x28
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-frddr.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-frddr.c
@@ -7,6 +7,7 @@
  * This driver implements the frontend playback DAI of AXG and G12A based SoCs
  */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/regmap.h>
 #include <linux/module.h>
@@ -59,8 +60,8 @@
 	/* Trim the FIFO depth if the period is small to improve latency */
 	depth = min(period, fifo->depth);
 	val = (depth / AXG_FIFO_BURST) - 1;
-	regmap_update_bits(fifo->map, FIFO_CTRL1, CTRL1_FRDDR_DEPTH_MASK,
-			   CTRL1_FRDDR_DEPTH(val));
+	regmap_update_bits(fifo->map, FIFO_CTRL1, CTRL1_FRDDR_DEPTH,
+			   FIELD_PREP(CTRL1_FRDDR_DEPTH, val));
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-pdm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-pdm.c
@@ -586,7 +586,6 @@
 	struct device *dev = &pdev->dev;
 	struct axg_pdm *priv;
 	void __iomem *regs;
-	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -611,28 +610,16 @@
 	}
 
 	priv->pclk = devm_clk_get(dev, "pclk");
-	if (IS_ERR(priv->pclk)) {
-		ret = PTR_ERR(priv->pclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get pclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->pclk))
+		return dev_err_probe(dev, PTR_ERR(priv->pclk), "failed to get pclk\n");
 
 	priv->dclk = devm_clk_get(dev, "dclk");
-	if (IS_ERR(priv->dclk)) {
-		ret = PTR_ERR(priv->dclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get dclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->dclk))
+		return dev_err_probe(dev, PTR_ERR(priv->dclk), "failed to get dclk\n");
 
 	priv->sysclk = devm_clk_get(dev, "sysclk");
-	if (IS_ERR(priv->sysclk)) {
-		ret = PTR_ERR(priv->sysclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get dclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->sysclk))
+		return dev_err_probe(dev, PTR_ERR(priv->sysclk), "failed to get dclk\n");
 
 	return devm_snd_soc_register_component(dev, &axg_pdm_component_drv,
 					       &axg_pdm_dai_drv, 1);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-spdifin.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-spdifin.c
@@ -112,34 +112,6 @@
 	return 0;
 }
 
-static int axg_spdifin_startup(struct snd_pcm_substream *substream,
-			       struct snd_soc_dai *dai)
-{
-	struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai);
-	int ret;
-
-	ret = clk_prepare_enable(priv->refclk);
-	if (ret) {
-		dev_err(dai->dev,
-			"failed to enable spdifin reference clock\n");
-		return ret;
-	}
-
-	regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN,
-			   SPDIFIN_CTRL0_EN);
-
-	return 0;
-}
-
-static void axg_spdifin_shutdown(struct snd_pcm_substream *substream,
-				 struct snd_soc_dai *dai)
-{
-	struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai);
-
-	regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN, 0);
-	clk_disable_unprepare(priv->refclk);
-}
-
 static void axg_spdifin_write_mode_param(struct regmap *map, int mode,
 					 unsigned int val,
 					 unsigned int num_per_reg,
@@ -251,25 +223,38 @@
 	ret = axg_spdifin_sample_mode_config(dai, priv);
 	if (ret) {
 		dev_err(dai->dev, "mode configuration failed\n");
-		clk_disable_unprepare(priv->pclk);
-		return ret;
+		goto pclk_err;
 	}
 
+	ret = clk_prepare_enable(priv->refclk);
+	if (ret) {
+		dev_err(dai->dev,
+			"failed to enable spdifin reference clock\n");
+		goto pclk_err;
+	}
+
+	regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN,
+			   SPDIFIN_CTRL0_EN);
+
 	return 0;
+
+pclk_err:
+	clk_disable_unprepare(priv->pclk);
+	return ret;
 }
 
 static int axg_spdifin_dai_remove(struct snd_soc_dai *dai)
 {
 	struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai);
 
+	regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN, 0);
+	clk_disable_unprepare(priv->refclk);
 	clk_disable_unprepare(priv->pclk);
 	return 0;
 }
 
 static const struct snd_soc_dai_ops axg_spdifin_ops = {
 	.prepare	= axg_spdifin_prepare,
-	.startup	= axg_spdifin_startup,
-	.shutdown	= axg_spdifin_shutdown,
 };
 
 static int axg_spdifin_iec958_info(struct snd_kcontrol *kcontrol,
@@ -454,7 +439,6 @@
 	struct axg_spdifin *priv;
 	struct snd_soc_dai_driver *dai_drv;
 	void __iomem *regs;
-	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -479,20 +463,12 @@
 	}
 
 	priv->pclk = devm_clk_get(dev, "pclk");
-	if (IS_ERR(priv->pclk)) {
-		ret = PTR_ERR(priv->pclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get pclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->pclk))
+		return dev_err_probe(dev, PTR_ERR(priv->pclk), "failed to get pclk\n");
 
 	priv->refclk = devm_clk_get(dev, "refclk");
-	if (IS_ERR(priv->refclk)) {
-		ret = PTR_ERR(priv->refclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get mclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->refclk))
+		return dev_err_probe(dev, PTR_ERR(priv->refclk), "failed to get mclk\n");
 
 	dai_drv = axg_spdifin_get_dai_drv(dev, priv);
 	if (IS_ERR(dai_drv)) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-spdifout.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-spdifout.c
@@ -403,7 +403,6 @@
 	struct device *dev = &pdev->dev;
 	struct axg_spdifout *priv;
 	void __iomem *regs;
-	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -422,20 +421,12 @@
 	}
 
 	priv->pclk = devm_clk_get(dev, "pclk");
-	if (IS_ERR(priv->pclk)) {
-		ret = PTR_ERR(priv->pclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get pclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->pclk))
+		return dev_err_probe(dev, PTR_ERR(priv->pclk), "failed to get pclk\n");
 
 	priv->mclk = devm_clk_get(dev, "mclk");
-	if (IS_ERR(priv->mclk)) {
-		ret = PTR_ERR(priv->mclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get mclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(priv->mclk))
+		return dev_err_probe(dev, PTR_ERR(priv->mclk), "failed to get mclk\n");
 
 	return devm_snd_soc_register_component(dev, &axg_spdifout_component_drv,
 			axg_spdifout_dai_drv, ARRAY_SIZE(axg_spdifout_dai_drv));
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-tdm-formatter.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-tdm-formatter.c
@@ -30,27 +30,32 @@
 					struct axg_tdm_stream *ts,
 					unsigned int offset)
 {
-	unsigned int val, ch = ts->channels;
-	unsigned long mask;
-	int i, j;
+	unsigned int ch = ts->channels;
+	u32 val[AXG_TDM_NUM_LANES];
+	int i, j, k;
 
 	/*
-	 * Distribute the channels of the stream over the available slots
-	 * of each TDM lane
+	 * We need to mimick the slot distribution used by the HW to keep the
+	 * channel placement consistent regardless of the number of channel
+	 * in the stream. This is why the odd algorithm below is used.
 	 */
-	for (i = 0; i < AXG_TDM_NUM_LANES; i++) {
-		val = 0;
-		mask = ts->mask[i];
+	memset(val, 0, sizeof(*val) * AXG_TDM_NUM_LANES);
 
-		for (j = find_first_bit(&mask, 32);
-		     (j < 32) && ch;
-		     j = find_next_bit(&mask, 32, j + 1)) {
-			val |= 1 << j;
-			ch -= 1;
+	/*
+	 * Distribute the channels of the stream over the available slots
+	 * of each TDM lane. We need to go over the 32 slots ...
+	 */
+	for (i = 0; (i < 32) && ch; i += 2) {
+		/* ... of all the lanes ... */
+		for (j = 0; j < AXG_TDM_NUM_LANES; j++) {
+			/* ... then distribute the channels in pairs */
+			for (k = 0; k < 2; k++) {
+				if ((BIT(i + k) & ts->mask[j]) && ch) {
+					val[j] |= BIT(i + k);
+					ch -= 1;
+				}
+			}
 		}
-
-		regmap_write(map, offset, val);
-		offset += regmap_get_reg_stride(map);
 	}
 
 	/*
@@ -63,6 +68,11 @@
 		return -EINVAL;
 	}
 
+	for (i = 0; i < AXG_TDM_NUM_LANES; i++) {
+		regmap_write(map, offset, val[i]);
+		offset += regmap_get_reg_stride(map);
+	}
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(axg_tdm_formatter_set_channel_masks);
@@ -255,7 +265,6 @@
 	const struct axg_tdm_formatter_driver *drv;
 	struct axg_tdm_formatter *formatter;
 	void __iomem *regs;
-	int ret;
 
 	drv = of_device_get_match_data(dev);
 	if (!drv) {
@@ -282,57 +291,34 @@
 
 	/* Peripharal clock */
 	formatter->pclk = devm_clk_get(dev, "pclk");
-	if (IS_ERR(formatter->pclk)) {
-		ret = PTR_ERR(formatter->pclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get pclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(formatter->pclk))
+		return dev_err_probe(dev, PTR_ERR(formatter->pclk), "failed to get pclk\n");
 
 	/* Formatter bit clock */
 	formatter->sclk = devm_clk_get(dev, "sclk");
-	if (IS_ERR(formatter->sclk)) {
-		ret = PTR_ERR(formatter->sclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get sclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(formatter->sclk))
+		return dev_err_probe(dev, PTR_ERR(formatter->sclk), "failed to get sclk\n");
 
 	/* Formatter sample clock */
 	formatter->lrclk = devm_clk_get(dev, "lrclk");
-	if (IS_ERR(formatter->lrclk)) {
-		ret = PTR_ERR(formatter->lrclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get lrclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(formatter->lrclk))
+		return dev_err_probe(dev, PTR_ERR(formatter->lrclk), "failed to get lrclk\n");
 
 	/* Formatter bit clock input multiplexer */
 	formatter->sclk_sel = devm_clk_get(dev, "sclk_sel");
-	if (IS_ERR(formatter->sclk_sel)) {
-		ret = PTR_ERR(formatter->sclk_sel);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get sclk_sel: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(formatter->sclk_sel))
+		return dev_err_probe(dev, PTR_ERR(formatter->sclk_sel), "failed to get sclk_sel\n");
 
 	/* Formatter sample clock input multiplexer */
 	formatter->lrclk_sel = devm_clk_get(dev, "lrclk_sel");
-	if (IS_ERR(formatter->lrclk_sel)) {
-		ret = PTR_ERR(formatter->lrclk_sel);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get lrclk_sel: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(formatter->lrclk_sel))
+		return dev_err_probe(dev, PTR_ERR(formatter->lrclk_sel),
+				     "failed to get lrclk_sel\n");
 
 	/* Formatter dedicated reset line */
 	formatter->reset = devm_reset_control_get_optional_exclusive(dev, NULL);
-	if (IS_ERR(formatter->reset)) {
-		ret = PTR_ERR(formatter->reset);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get reset: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(formatter->reset))
+		return dev_err_probe(dev, PTR_ERR(formatter->reset), "failed to get reset\n");
 
 	return devm_snd_soc_register_component(dev, drv->component_drv,
 					       NULL, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-tdm-interface.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-tdm-interface.c
@@ -12,6 +12,9 @@
 
 #include "axg-tdm.h"
 
+/* Maximum bit clock frequency according the datasheets */
+#define MAX_SCLK 100000000 /* Hz */
+
 enum {
 	TDM_IFACE_PAD,
 	TDM_IFACE_LOOPBACK,
@@ -155,19 +158,27 @@
 		return -EINVAL;
 	}
 
-	/* Apply component wide rate symmetry */
 	if (snd_soc_component_active(dai->component)) {
+		/* Apply component wide rate symmetry */
 		ret = snd_pcm_hw_constraint_single(substream->runtime,
 						   SNDRV_PCM_HW_PARAM_RATE,
 						   iface->rate);
-		if (ret < 0) {
-			dev_err(dai->dev,
-				"can't set iface rate constraint\n");
-			return ret;
-		}
+
+	} else {
+		/* Limit rate according to the slot number and width */
+		unsigned int max_rate =
+			MAX_SCLK / (iface->slots * iface->slot_width);
+		ret = snd_pcm_hw_constraint_minmax(substream->runtime,
+						   SNDRV_PCM_HW_PARAM_RATE,
+						   0, max_rate);
 	}
 
-	return 0;
+	if (ret < 0)
+		dev_err(dai->dev, "can't set iface rate constraint\n");
+	else
+		ret = 0;
+
+	return ret;
 }
 
 static int axg_tdm_iface_set_stream(struct snd_pcm_substream *substream,
@@ -266,8 +277,8 @@
 	srate = iface->slots * iface->slot_width * params_rate(params);
 
 	if (!iface->mclk_rate) {
-		/* If no specific mclk is requested, default to bit clock * 4 */
-		clk_set_rate(iface->mclk, 4 * srate);
+		/* If no specific mclk is requested, default to bit clock * 2 */
+		clk_set_rate(iface->mclk, 2 * srate);
 	} else {
 		/* Check if we can actually get the bit clock from mclk */
 		if (iface->mclk_rate % srate) {
@@ -351,13 +362,29 @@
 	return 0;
 }
 
-static int axg_tdm_iface_prepare(struct snd_pcm_substream *substream,
+static int axg_tdm_iface_trigger(struct snd_pcm_substream *substream,
+				 int cmd,
 				 struct snd_soc_dai *dai)
 {
-	struct axg_tdm_stream *ts = snd_soc_dai_get_dma_data(dai, substream);
+	struct axg_tdm_stream *ts =
+		snd_soc_dai_get_dma_data(dai, substream);
 
-	/* Force all attached formatters to update */
-	return axg_tdm_stream_reset(ts);
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_START:
+	case SNDRV_PCM_TRIGGER_RESUME:
+	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+		axg_tdm_stream_start(ts);
+		break;
+	case SNDRV_PCM_TRIGGER_SUSPEND:
+	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+	case SNDRV_PCM_TRIGGER_STOP:
+		axg_tdm_stream_stop(ts);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
 }
 
 static int axg_tdm_iface_remove_dai(struct snd_soc_dai *dai)
@@ -397,8 +424,8 @@
 	.set_fmt	= axg_tdm_iface_set_fmt,
 	.startup	= axg_tdm_iface_startup,
 	.hw_params	= axg_tdm_iface_hw_params,
-	.prepare	= axg_tdm_iface_prepare,
 	.hw_free	= axg_tdm_iface_hw_free,
+	.trigger	= axg_tdm_iface_trigger,
 };
 
 /* TDM Backend DAIs */
@@ -517,21 +544,13 @@
 
 	/* Bit clock provided on the pad */
 	iface->sclk = devm_clk_get(dev, "sclk");
-	if (IS_ERR(iface->sclk)) {
-		ret = PTR_ERR(iface->sclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get sclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(iface->sclk))
+		return dev_err_probe(dev, PTR_ERR(iface->sclk), "failed to get sclk\n");
 
 	/* Sample clock provided on the pad */
 	iface->lrclk = devm_clk_get(dev, "lrclk");
-	if (IS_ERR(iface->lrclk)) {
-		ret = PTR_ERR(iface->lrclk);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get lrclk: %d\n", ret);
-		return ret;
-	}
+	if (IS_ERR(iface->lrclk))
+		return dev_err_probe(dev, PTR_ERR(iface->lrclk), "failed to get lrclk\n");
 
 	/*
 	 * mclk maybe be missing when the cpu dai is in slave mode and
@@ -542,13 +561,10 @@
 	iface->mclk = devm_clk_get(dev, "mclk");
 	if (IS_ERR(iface->mclk)) {
 		ret = PTR_ERR(iface->mclk);
-		if (ret == -ENOENT) {
+		if (ret == -ENOENT)
 			iface->mclk = NULL;
-		} else {
-			if (ret != -EPROBE_DEFER)
-				dev_err(dev, "failed to get mclk: %d\n", ret);
-			return ret;
-		}
+		else
+			return dev_err_probe(dev, ret, "failed to get mclk\n");
 	}
 
 	return devm_snd_soc_register_component(dev,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/axg-toddr.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/axg-toddr.c
@@ -5,6 +5,7 @@
 
 /* This driver implements the frontend capture DAI of AXG based SoCs */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/regmap.h>
 #include <linux/module.h>
@@ -19,12 +20,9 @@
 #define CTRL0_TODDR_EXT_SIGNED		BIT(29)
 #define CTRL0_TODDR_PP_MODE		BIT(28)
 #define CTRL0_TODDR_SYNC_CH		BIT(27)
-#define CTRL0_TODDR_TYPE_MASK		GENMASK(15, 13)
-#define CTRL0_TODDR_TYPE(x)		((x) << 13)
-#define CTRL0_TODDR_MSB_POS_MASK	GENMASK(12, 8)
-#define CTRL0_TODDR_MSB_POS(x)		((x) << 8)
-#define CTRL0_TODDR_LSB_POS_MASK	GENMASK(7, 3)
-#define CTRL0_TODDR_LSB_POS(x)		((x) << 3)
+#define CTRL0_TODDR_TYPE		GENMASK(15, 13)
+#define CTRL0_TODDR_MSB_POS		GENMASK(12, 8)
+#define CTRL0_TODDR_LSB_POS		GENMASK(7, 3)
 #define CTRL1_TODDR_FORCE_FINISH	BIT(25)
 #define CTRL1_SEL_SHIFT			28
 
@@ -76,12 +74,12 @@
 	width = params_width(params);
 
 	regmap_update_bits(fifo->map, FIFO_CTRL0,
-			   CTRL0_TODDR_TYPE_MASK |
-			   CTRL0_TODDR_MSB_POS_MASK |
-			   CTRL0_TODDR_LSB_POS_MASK,
-			   CTRL0_TODDR_TYPE(type) |
-			   CTRL0_TODDR_MSB_POS(TODDR_MSB_POS) |
-			   CTRL0_TODDR_LSB_POS(TODDR_MSB_POS - (width - 1)));
+			   CTRL0_TODDR_TYPE |
+			   CTRL0_TODDR_MSB_POS |
+			   CTRL0_TODDR_LSB_POS,
+			   FIELD_PREP(CTRL0_TODDR_TYPE, type) |
+			   FIELD_PREP(CTRL0_TODDR_MSB_POS, TODDR_MSB_POS) |
+			   FIELD_PREP(CTRL0_TODDR_LSB_POS, TODDR_MSB_POS - (width - 1)));
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/g12a-toacodec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/g12a-toacodec.c
@@ -71,6 +71,9 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	unsigned int mux, reg;
 
+	if (ucontrol->value.enumerated.item[0] >= e->items)
+		return -EINVAL;
+
 	mux = snd_soc_enum_item_to_val(e, ucontrol->value.enumerated.item[0]);
 	regmap_field_read(priv->field_dat_sel, &reg);
 
@@ -101,7 +104,7 @@
 
 	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
 
-	return 0;
+	return 1;
 }
 
 static SOC_ENUM_SINGLE_DECL(g12a_toacodec_mux_enum, TOACODEC_CTRL0,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/g12a-tohdmitx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/g12a-tohdmitx.c
@@ -45,6 +45,9 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	unsigned int mux, changed;
 
+	if (ucontrol->value.enumerated.item[0] >= e->items)
+		return -EINVAL;
+
 	mux = snd_soc_enum_item_to_val(e, ucontrol->value.enumerated.item[0]);
 	changed = snd_soc_component_test_bits(component, e->reg,
 					      CTRL0_I2S_DAT_SEL,
@@ -67,7 +70,7 @@
 
 	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
 
-	return 0;
+	return 1;
 }
 
 static SOC_ENUM_SINGLE_DECL(g12a_tohdmitx_i2s_mux_enum, TOHDMITX_CTRL0,
@@ -93,6 +96,9 @@
 	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
 	unsigned int mux, changed;
 
+	if (ucontrol->value.enumerated.item[0] >= e->items)
+		return -EINVAL;
+
 	mux = snd_soc_enum_item_to_val(e, ucontrol->value.enumerated.item[0]);
 	changed = snd_soc_component_test_bits(component, TOHDMITX_CTRL0,
 					      CTRL0_SPDIF_SEL,
@@ -112,7 +118,7 @@
 
 	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
 
-	return 0;
+	return 1;
 }
 
 static SOC_ENUM_SINGLE_DECL(g12a_tohdmitx_spdif_mux_enum, TOHDMITX_CTRL0,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/meson-card-utils.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/meson-card-utils.c
@@ -85,11 +85,9 @@
 
 	ret = of_parse_phandle_with_args(node, "sound-dai",
 					 "#sound-dai-cells", 0, &args);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(card->dev, "can't parse dai %d\n", ret);
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(card->dev, ret, "can't parse dai\n");
+
 	*dai_of_node = args.np;
 
 	return snd_soc_get_dai_name(&args, dai_name);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/meson/t9015.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/meson/t9015.c
@@ -48,7 +48,6 @@
 #define POWER_CFG	0x10
 
 struct t9015 {
-	struct clk *pclk;
 	struct regulator *avdd;
 };
 
@@ -250,6 +249,7 @@
 	struct t9015 *priv;
 	void __iomem *regs;
 	struct regmap *regmap;
+	struct clk *pclk;
 	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -257,31 +257,13 @@
 		return -ENOMEM;
 	platform_set_drvdata(pdev, priv);
 
-	priv->pclk = devm_clk_get(dev, "pclk");
-	if (IS_ERR(priv->pclk)) {
-		if (PTR_ERR(priv->pclk) != -EPROBE_DEFER)
-			dev_err(dev, "failed to get core clock\n");
-		return PTR_ERR(priv->pclk);
-	}
+	pclk = devm_clk_get_enabled(dev, "pclk");
+	if (IS_ERR(pclk))
+		return dev_err_probe(dev, PTR_ERR(pclk), "failed to get core clock\n");
 
 	priv->avdd = devm_regulator_get(dev, "AVDD");
-	if (IS_ERR(priv->avdd)) {
-		if (PTR_ERR(priv->avdd) != -EPROBE_DEFER)
-			dev_err(dev, "failed to AVDD\n");
-		return PTR_ERR(priv->avdd);
-	}
-
-	ret = clk_prepare_enable(priv->pclk);
-	if (ret) {
-		dev_err(dev, "core clock enable failed\n");
-		return ret;
-	}
-
-	ret = devm_add_action_or_reset(dev,
-			(void(*)(void *))clk_disable_unprepare,
-			priv->pclk);
-	if (ret)
-		return ret;
+	if (IS_ERR(priv->avdd))
+		return dev_err_probe(dev, PTR_ERR(priv->avdd), "failed to AVDD\n");
 
 	ret = device_reset(dev);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mxs/mxs-saif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mxs/mxs-saif.c
@@ -455,7 +455,10 @@
 		* basic clock which should be fast enough for the internal
 		* logic.
 		*/
-		clk_enable(saif->clk);
+		ret = clk_enable(saif->clk);
+		if (ret)
+			return ret;
+
 		ret = clk_set_rate(saif->clk, 24000000);
 		clk_disable(saif->clk);
 		if (ret)
@@ -751,6 +754,7 @@
 		saif->master_id = saif->id;
 	} else {
 		ret = of_alias_get_id(master, "saif");
+		of_node_put(master);
 		if (ret < 0)
 			return ret;
 		else
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/mxs/mxs-sgtl5000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/mxs/mxs-sgtl5000.c
@@ -118,6 +118,9 @@
 	codec_np = of_parse_phandle(np, "audio-codec", 0);
 	if (!saif_np[0] || !saif_np[1] || !codec_np) {
 		dev_err(&pdev->dev, "phandle missing or invalid\n");
+		of_node_put(codec_np);
+		of_node_put(saif_np[0]);
+		of_node_put(saif_np[1]);
 		return -EINVAL;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/pxa/mmp-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/pxa/mmp-pcm.c
@@ -98,7 +98,7 @@
 
 	devname = kasprintf(GFP_KERNEL, "%s.%d", dma_data->dma_res->name,
 		dma_data->ssp_id);
-	if ((strcmp(dev_name(chan->device->dev), devname) == 0) &&
+	if (devname && (strcmp(dev_name(chan->device->dev), devname) == 0) &&
 		(chan->chan_id == dma_data->dma_res->start)) {
 		found = true;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/pxa/pxa-ssp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/pxa/pxa-ssp.c
@@ -779,7 +779,7 @@
 		if (IS_ERR(priv->extclk)) {
 			ret = PTR_ERR(priv->extclk);
 			if (ret == -EPROBE_DEFER)
-				return ret;
+				goto err_priv;
 
 			priv->extclk = NULL;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/pxa/spitz.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/pxa/spitz.c
@@ -14,13 +14,12 @@
 #include <linux/timer.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <sound/core.h>
 #include <sound/pcm.h>
 #include <sound/soc.h>
 
 #include <asm/mach-types.h>
-#include <mach/spitz.h>
 #include "../codecs/wm8750.h"
 #include "pxa2xx-i2s.h"
 
@@ -37,7 +36,7 @@
 
 static int spitz_jack_func;
 static int spitz_spk_func;
-static int spitz_mic_gpio;
+static struct gpio_desc *gpiod_mic, *gpiod_mute_l, *gpiod_mute_r;
 
 static void spitz_ext_control(struct snd_soc_dapm_context *dapm)
 {
@@ -56,8 +55,8 @@
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Mic Jack");
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Line Jack");
 		snd_soc_dapm_enable_pin_unlocked(dapm, "Headphone Jack");
-		gpio_set_value(SPITZ_GPIO_MUTE_L, 1);
-		gpio_set_value(SPITZ_GPIO_MUTE_R, 1);
+		gpiod_set_value(gpiod_mute_l, 1);
+		gpiod_set_value(gpiod_mute_r, 1);
 		break;
 	case SPITZ_MIC:
 		/* enable mic jack and bias, mute hp */
@@ -65,8 +64,8 @@
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Headset Jack");
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Line Jack");
 		snd_soc_dapm_enable_pin_unlocked(dapm, "Mic Jack");
-		gpio_set_value(SPITZ_GPIO_MUTE_L, 0);
-		gpio_set_value(SPITZ_GPIO_MUTE_R, 0);
+		gpiod_set_value(gpiod_mute_l, 0);
+		gpiod_set_value(gpiod_mute_r, 0);
 		break;
 	case SPITZ_LINE:
 		/* enable line jack, disable mic bias and mute hp */
@@ -74,8 +73,8 @@
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Headset Jack");
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Mic Jack");
 		snd_soc_dapm_enable_pin_unlocked(dapm, "Line Jack");
-		gpio_set_value(SPITZ_GPIO_MUTE_L, 0);
-		gpio_set_value(SPITZ_GPIO_MUTE_R, 0);
+		gpiod_set_value(gpiod_mute_l, 0);
+		gpiod_set_value(gpiod_mute_r, 0);
 		break;
 	case SPITZ_HEADSET:
 		/* enable and unmute headset jack enable mic bias, mute L hp */
@@ -83,8 +82,8 @@
 		snd_soc_dapm_enable_pin_unlocked(dapm, "Mic Jack");
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Line Jack");
 		snd_soc_dapm_enable_pin_unlocked(dapm, "Headset Jack");
-		gpio_set_value(SPITZ_GPIO_MUTE_L, 0);
-		gpio_set_value(SPITZ_GPIO_MUTE_R, 1);
+		gpiod_set_value(gpiod_mute_l, 0);
+		gpiod_set_value(gpiod_mute_r, 1);
 		break;
 	case SPITZ_HP_OFF:
 
@@ -93,8 +92,8 @@
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Headset Jack");
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Mic Jack");
 		snd_soc_dapm_disable_pin_unlocked(dapm, "Line Jack");
-		gpio_set_value(SPITZ_GPIO_MUTE_L, 0);
-		gpio_set_value(SPITZ_GPIO_MUTE_R, 0);
+		gpiod_set_value(gpiod_mute_l, 0);
+		gpiod_set_value(gpiod_mute_r, 0);
 		break;
 	}
 
@@ -199,7 +198,7 @@
 static int spitz_mic_bias(struct snd_soc_dapm_widget *w,
 	struct snd_kcontrol *k, int event)
 {
-	gpio_set_value_cansleep(spitz_mic_gpio, SND_SOC_DAPM_EVENT_ON(event));
+	gpiod_set_value_cansleep(gpiod_mic, SND_SOC_DAPM_EVENT_ON(event));
 	return 0;
 }
 
@@ -287,39 +286,28 @@
 	struct snd_soc_card *card = &snd_soc_spitz;
 	int ret;
 
-	if (machine_is_akita())
-		spitz_mic_gpio = AKITA_GPIO_MIC_BIAS;
-	else
-		spitz_mic_gpio = SPITZ_GPIO_MIC_BIAS;
-
-	ret = gpio_request(spitz_mic_gpio, "MIC GPIO");
-	if (ret)
-		goto err1;
-
-	ret = gpio_direction_output(spitz_mic_gpio, 0);
-	if (ret)
-		goto err2;
+	gpiod_mic = devm_gpiod_get(&pdev->dev, "mic", GPIOD_OUT_LOW);
+	if (IS_ERR(gpiod_mic))
+		return PTR_ERR(gpiod_mic);
+	gpiod_mute_l = devm_gpiod_get(&pdev->dev, "mute-l", GPIOD_OUT_LOW);
+	if (IS_ERR(gpiod_mute_l))
+		return PTR_ERR(gpiod_mute_l);
+	gpiod_mute_r = devm_gpiod_get(&pdev->dev, "mute-r", GPIOD_OUT_LOW);
+	if (IS_ERR(gpiod_mute_r))
+		return PTR_ERR(gpiod_mute_r);
 
 	card->dev = &pdev->dev;
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
-	if (ret) {
+	if (ret)
 		dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
 			ret);
-		goto err2;
-	}
-
-	return 0;
 
-err2:
-	gpio_free(spitz_mic_gpio);
-err1:
 	return ret;
 }
 
 static int spitz_remove(struct platform_device *pdev)
 {
-	gpio_free(spitz_mic_gpio);
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/lpass-cpu.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/lpass-cpu.c
@@ -779,10 +779,20 @@
 		return true;
 	if (reg == LPASS_HDMI_TX_LEGACY_ADDR(v))
 		return true;
+	if (reg == LPASS_HDMI_TX_VBIT_CTL_ADDR(v))
+		return true;
+	if (reg == LPASS_HDMI_TX_PARITY_ADDR(v))
+		return true;
 
 	for (i = 0; i < v->hdmi_rdma_channels; ++i) {
 		if (reg == LPAIF_HDMI_RDMACURR_REG(v, i))
 			return true;
+		if (reg == LPASS_HDMI_TX_DMA_ADDR(v, i))
+			return true;
+		if (reg == LPASS_HDMI_TX_CH_LSB_ADDR(v, i))
+			return true;
+		if (reg == LPASS_HDMI_TX_CH_MSB_ADDR(v, i))
+			return true;
 	}
 	return false;
 }
@@ -841,10 +851,11 @@
 					struct lpass_data *data)
 {
 	struct device_node *node;
-	int ret, id;
+	int ret, i, id;
 
 	/* Allow all channels by default for backwards compatibility */
-	for (id = 0; id < data->variant->num_dai; id++) {
+	for (i = 0; i < data->variant->num_dai; i++) {
+		id = data->variant->dai_driver[i].id;
 		data->mi2s_playback_sd_mode[id] = LPAIF_I2SCTL_MODE_8CH;
 		data->mi2s_capture_sd_mode[id] = LPAIF_I2SCTL_MODE_8CH;
 	}
@@ -880,6 +891,7 @@
 	dsp_of_node = of_parse_phandle(pdev->dev.of_node, "qcom,adsp", 0);
 	if (dsp_of_node) {
 		dev_err(dev, "DSP exists and holds audio resources\n");
+		of_node_put(dsp_of_node);
 		return -EBUSY;
 	}
 
@@ -963,6 +975,8 @@
 	/* Allocation for i2sctl regmap fields */
 	drvdata->i2sctl = devm_kzalloc(&pdev->dev, sizeof(struct lpaif_i2sctl),
 					GFP_KERNEL);
+	if (!drvdata->i2sctl)
+		return -ENOMEM;
 
 	/* Initialize bitfields for dai I2SCTL register */
 	ret = lpass_cpu_init_i2sctl_bitfields(dev, drvdata->i2sctl,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/lpass-platform.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/lpass-platform.c
@@ -524,7 +524,7 @@
 			return -EINVAL;
 		}
 
-		ret = regmap_update_bits(map, reg_irqclr, val_irqclr, val_irqclr);
+		ret = regmap_write_bits(map, reg_irqclr, val_irqclr, val_irqclr);
 		if (ret) {
 			dev_err(soc_runtime->dev, "error writing to irqclear reg: %d\n", ret);
 			return ret;
@@ -665,7 +665,7 @@
 	return -EINVAL;
 	}
 	if (interrupts & LPAIF_IRQ_PER(chan)) {
-		rv = regmap_update_bits(map, reg, mask, (LPAIF_IRQ_PER(chan) | val));
+		rv = regmap_write_bits(map, reg, mask, (LPAIF_IRQ_PER(chan) | val));
 		if (rv) {
 			dev_err(soc_runtime->dev,
 				"error writing to irqclear reg: %d\n", rv);
@@ -676,7 +676,7 @@
 	}
 
 	if (interrupts & LPAIF_IRQ_XRUN(chan)) {
-		rv = regmap_update_bits(map, reg, mask, (LPAIF_IRQ_XRUN(chan) | val));
+		rv = regmap_write_bits(map, reg, mask, (LPAIF_IRQ_XRUN(chan) | val));
 		if (rv) {
 			dev_err(soc_runtime->dev,
 				"error writing to irqclear reg: %d\n", rv);
@@ -688,7 +688,7 @@
 	}
 
 	if (interrupts & LPAIF_IRQ_ERR(chan)) {
-		rv = regmap_update_bits(map, reg, mask, (LPAIF_IRQ_ERR(chan) | val));
+		rv = regmap_write_bits(map, reg, mask, (LPAIF_IRQ_ERR(chan) | val));
 		if (rv) {
 			dev_err(soc_runtime->dev,
 				"error writing to irqclear reg: %d\n", rv);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/lpass-sc7180.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/lpass-sc7180.c
@@ -131,6 +131,9 @@
 
 	drvdata->clks = devm_kcalloc(dev, variant->num_clks,
 				     sizeof(*drvdata->clks), GFP_KERNEL);
+	if (!drvdata->clks)
+		return -ENOMEM;
+
 	drvdata->num_clks = variant->num_clks;
 
 	for (i = 0; i < drvdata->num_clks; i++)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/qdsp6/q6adm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/qdsp6/q6adm.c
@@ -217,7 +217,7 @@
 	idx = find_first_zero_bit(&adm->copp_bitmap[port_idx],
 				  MAX_COPPS_PER_PORT);
 
-	if (idx > MAX_COPPS_PER_PORT)
+	if (idx >= MAX_COPPS_PER_PORT)
 		return ERR_PTR(-EBUSY);
 
 	c = kzalloc(sizeof(*c), GFP_ATOMIC);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/qdsp6/q6asm-dai.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/qdsp6/q6asm-dai.c
@@ -269,9 +269,7 @@
 
 	if (ret < 0) {
 		dev_err(dev, "%s: q6asm_open_write failed\n", __func__);
-		q6asm_audio_client_free(prtd->audio_client);
-		prtd->audio_client = NULL;
-		return -ENOMEM;
+		goto open_err;
 	}
 
 	prtd->session_id = q6asm_get_session_id(prtd->audio_client);
@@ -279,7 +277,7 @@
 			      prtd->session_id, substream->stream);
 	if (ret) {
 		dev_err(dev, "%s: stream reg failed ret:%d\n", __func__, ret);
-		return ret;
+		goto routing_err;
 	}
 
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
@@ -301,10 +299,19 @@
 	}
 	if (ret < 0)
 		dev_info(dev, "%s: CMD Format block failed\n", __func__);
+	else
+		prtd->state = Q6ASM_STREAM_RUNNING;
 
-	prtd->state = Q6ASM_STREAM_RUNNING;
+	return ret;
 
-	return 0;
+routing_err:
+	q6asm_cmd(prtd->audio_client, prtd->stream_id,  CMD_CLOSE);
+open_err:
+	q6asm_unmap_memory_regions(substream->stream, prtd->audio_client);
+	q6asm_audio_client_free(prtd->audio_client);
+	prtd->audio_client = NULL;
+
+	return ret;
 }
 
 static int q6asm_dai_trigger(struct snd_soc_component *component,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/qdsp6/q6routing.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/qdsp6/q6routing.c
@@ -492,9 +492,15 @@
 	struct session_data *session = &data->sessions[session_id];
 
 	if (ucontrol->value.integer.value[0]) {
+		if (session->port_id == be_id)
+			return 0;
+
 		session->port_id = be_id;
 		snd_soc_dapm_mixer_update_power(dapm, kcontrol, 1, update);
 	} else {
+		if (session->port_id == -1 || session->port_id != be_id)
+			return 0;
+
 		session->port_id = -1;
 		snd_soc_dapm_mixer_update_power(dapm, kcontrol, 0, update);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/sdm845.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/sdm845.c
@@ -56,8 +56,8 @@
 	int ret = 0, i;
 
 	for_each_rtd_codec_dais(rtd, i, codec_dai) {
-		sruntime = snd_soc_dai_get_sdw_stream(codec_dai,
-						      substream->stream);
+		sruntime = snd_soc_dai_get_stream(codec_dai,
+						  substream->stream);
 		if (sruntime != ERR_PTR(-ENOTSUPP))
 			pdata->sruntime[cpu_dai->id] = sruntime;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/qcom/sm8250.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/qcom/sm8250.c
@@ -70,8 +70,8 @@
 	switch (cpu_dai->id) {
 	case WSA_CODEC_DMA_RX_0:
 		for_each_rtd_codec_dais(rtd, i, codec_dai) {
-			sruntime = snd_soc_dai_get_sdw_stream(codec_dai,
-						      substream->stream);
+			sruntime = snd_soc_dai_get_stream(codec_dai,
+							  substream->stream);
 			if (sruntime != ERR_PTR(-ENOTSUPP))
 				pdata->sruntime[cpu_dai->id] = sruntime;
 		}
@@ -191,6 +191,7 @@
 	if (!card)
 		return -ENOMEM;
 
+	card->owner = THIS_MODULE;
 	/* Allocate the private data */
 	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
 	if (!data)
@@ -210,6 +211,7 @@
 
 static const struct of_device_id snd_sm8250_dt_match[] = {
 	{.compatible = "qcom,sm8250-sndcard"},
+	{.compatible = "qcom,qrb4210-rb2-sndcard"},
 	{.compatible = "qcom,qrb5165-rb5-sndcard"},
 	{}
 };
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/rockchip/rockchip_i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/rockchip/rockchip_i2s.c
@@ -717,19 +717,23 @@
 	i2s->mclk = devm_clk_get(&pdev->dev, "i2s_clk");
 	if (IS_ERR(i2s->mclk)) {
 		dev_err(&pdev->dev, "Can't retrieve i2s master clock\n");
-		return PTR_ERR(i2s->mclk);
+		ret = PTR_ERR(i2s->mclk);
+		goto err_clk;
 	}
 
 	regs = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
-	if (IS_ERR(regs))
-		return PTR_ERR(regs);
+	if (IS_ERR(regs)) {
+		ret = PTR_ERR(regs);
+		goto err_clk;
+	}
 
 	i2s->regmap = devm_regmap_init_mmio(&pdev->dev, regs,
 					    &rockchip_i2s_regmap_config);
 	if (IS_ERR(i2s->regmap)) {
 		dev_err(&pdev->dev,
 			"Failed to initialise managed register map\n");
-		return PTR_ERR(i2s->regmap);
+		ret = PTR_ERR(i2s->regmap);
+		goto err_clk;
 	}
 
 	i2s->bclk_ratio = 64;
@@ -769,7 +773,8 @@
 		i2s_runtime_suspend(&pdev->dev);
 err_pm_disable:
 	pm_runtime_disable(&pdev->dev);
-
+err_clk:
+	clk_disable_unprepare(i2s->hclk);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/rockchip/rockchip_pdm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/rockchip/rockchip_pdm.c
@@ -368,6 +368,7 @@
 
 	ret = clk_prepare_enable(pdm->hclk);
 	if (ret) {
+		clk_disable_unprepare(pdm->clk);
 		dev_err(pdm->dev, "hclock enable failed %d\n", ret);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/rockchip/rockchip_spdif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/rockchip/rockchip_spdif.c
@@ -88,6 +88,7 @@
 
 	ret = clk_prepare_enable(spdif->hclk);
 	if (ret) {
+		clk_disable_unprepare(spdif->mclk);
 		dev_err(spdif->dev, "hclk clock enable failed %d\n", ret);
 		return ret;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/Kconfig
@@ -214,8 +214,9 @@
 
 config SND_SOC_SAMSUNG_ARIES_WM8994
 	tristate "SoC I2S Audio support for WM8994 on Aries"
-	depends on SND_SOC_SAMSUNG && MFD_WM8994 && IIO && EXTCON
+	depends on SND_SOC_SAMSUNG && I2C && IIO && EXTCON
 	select SND_SOC_BT_SCO
+	select MFD_WM8994
 	select SND_SOC_WM8994
 	select SND_SAMSUNG_I2S
 	help
@@ -227,8 +228,9 @@
 
 config SND_SOC_SAMSUNG_MIDAS_WM1811
 	tristate "SoC I2S Audio support for Midas boards"
-	depends on SND_SOC_SAMSUNG
+	depends on SND_SOC_SAMSUNG && I2C
 	select SND_SAMSUNG_I2S
+	select MFD_WM8994
 	select SND_SOC_WM8994
 	help
 	  Say Y if you want to add support for SoC audio on the Midas boards.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/aries_wm8994.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/aries_wm8994.c
@@ -585,19 +585,16 @@
 
 	extcon_np = of_parse_phandle(np, "extcon", 0);
 	priv->usb_extcon = extcon_find_edev_by_node(extcon_np);
-	if (IS_ERR(priv->usb_extcon)) {
-		if (PTR_ERR(priv->usb_extcon) != -EPROBE_DEFER)
-			dev_err(dev, "Failed to get extcon device");
-		return PTR_ERR(priv->usb_extcon);
-	}
 	of_node_put(extcon_np);
+	if (IS_ERR(priv->usb_extcon))
+		return dev_err_probe(dev, PTR_ERR(priv->usb_extcon),
+				     "Failed to get extcon device");
 
 	priv->adc = devm_iio_channel_get(dev, "headset-detect");
-	if (IS_ERR(priv->adc)) {
-		if (PTR_ERR(priv->adc) != -EPROBE_DEFER)
-			dev_err(dev, "Failed to get ADC channel");
-		return PTR_ERR(priv->adc);
-	}
+	if (IS_ERR(priv->adc))
+		return dev_err_probe(dev, PTR_ERR(priv->adc),
+				     "Failed to get ADC channel");
+
 	if (priv->adc->channel->type != IIO_VOLTAGE)
 		return -EINVAL;
 
@@ -631,8 +628,10 @@
 		return -EINVAL;
 
 	codec = of_get_child_by_name(dev->of_node, "codec");
-	if (!codec)
-		return -EINVAL;
+	if (!codec) {
+		ret = -EINVAL;
+		goto out;
+	}
 
 	for_each_card_prelinks(card, i, dai_link) {
 		dai_link->codecs->of_node = of_parse_phandle(codec,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/arndale.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/arndale.c
@@ -174,9 +174,8 @@
 
 	ret = devm_snd_soc_register_card(card->dev, card);
 	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(&pdev->dev,
-				"snd_soc_register_card() failed: %d\n", ret);
+		dev_err_probe(&pdev->dev, ret,
+			      "snd_soc_register_card() failed\n");
 		goto err_put_of_nodes;
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/h1940_uda1380.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/h1940_uda1380.c
@@ -8,7 +8,7 @@
 // Based on version from Arnaud Patard <arnaud.patard@rtp-net.org>
 
 #include <linux/types.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/module.h>
 
 #include <sound/soc.h>
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/idma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/idma.c
@@ -360,6 +360,8 @@
 	buf->addr = idma.lp_tx_addr;
 	buf->bytes = idma_hardware.buffer_bytes_max;
 	buf->area = (unsigned char * __force)ioremap(buf->addr, buf->bytes);
+	if (!buf->area)
+		return -ENOMEM;
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/littlemill.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/littlemill.c
@@ -325,9 +325,8 @@
 	card->dev = &pdev->dev;
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-			ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card() failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/lowland.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/lowland.c
@@ -183,9 +183,8 @@
 	card->dev = &pdev->dev;
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-			ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card() failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/odroid.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/odroid.c
@@ -311,9 +311,7 @@
 
 	ret = devm_snd_soc_register_card(dev, card);
 	if (ret < 0) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "snd_soc_register_card() failed: %d\n",
-				ret);
+		dev_err_probe(dev, ret, "snd_soc_register_card() failed\n");
 		goto err_put_clk_i2s;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/rx1950_uda1380.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/rx1950_uda1380.c
@@ -128,7 +128,7 @@
 					&hw_rates);
 }
 
-struct gpio_desc *gpiod_speaker_power;
+static struct gpio_desc *gpiod_speaker_power;
 
 static int rx1950_spk_power(struct snd_soc_dapm_widget *w,
 				struct snd_kcontrol *kcontrol, int event)
@@ -227,7 +227,7 @@
 	return devm_snd_soc_register_card(dev, &rx1950_asoc);
 }
 
-struct platform_driver rx1950_audio = {
+static struct platform_driver rx1950_audio = {
 	.driver = {
 		.name = "rx1950-audio",
 		.pm = &snd_soc_pm_ops,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/smdk_wm8994.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/smdk_wm8994.c
@@ -179,8 +179,8 @@
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
 
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card() failed:%d\n", ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card() failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/smdk_wm8994pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/smdk_wm8994pcm.c
@@ -118,8 +118,8 @@
 
 	smdk_pcm.dev = &pdev->dev;
 	ret = devm_snd_soc_register_card(&pdev->dev, &smdk_pcm);
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card failed %d\n", ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/snow.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/snow.c
@@ -212,12 +212,9 @@
 	snd_soc_card_set_drvdata(card, priv);
 
 	ret = devm_snd_soc_register_card(dev, card);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(&pdev->dev,
-				"snd_soc_register_card failed (%d)\n", ret);
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret,
+				     "snd_soc_register_card failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/speyside.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/speyside.c
@@ -330,9 +330,8 @@
 	card->dev = &pdev->dev;
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-			ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card() failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/tm2_wm5110.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/tm2_wm5110.c
@@ -612,8 +612,7 @@
 
 	ret = devm_snd_soc_register_card(dev, card);
 	if (ret < 0) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "Failed to register card: %d\n", ret);
+		dev_err_probe(dev, ret, "Failed to register card\n");
 		goto dai_node_put;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/samsung/tobermory.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/samsung/tobermory.c
@@ -229,9 +229,8 @@
 	card->dev = &pdev->dev;
 
 	ret = devm_snd_soc_register_card(&pdev->dev, card);
-	if (ret && ret != -EPROBE_DEFER)
-		dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-			ret);
+	if (ret)
+		dev_err_probe(&pdev->dev, ret, "snd_soc_register_card() failed\n");
 
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/fsi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/fsi.c
@@ -816,14 +816,27 @@
 			return ret;
 		}
 
-		clk_enable(clock->xck);
-		clk_enable(clock->ick);
-		clk_enable(clock->div);
+		ret = clk_enable(clock->xck);
+		if (ret)
+			goto err;
+		ret = clk_enable(clock->ick);
+		if (ret)
+			goto disable_xck;
+		ret = clk_enable(clock->div);
+		if (ret)
+			goto disable_ick;
 
 		clock->count++;
 	}
 
 	return ret;
+
+disable_ick:
+	clk_disable(clock->ick);
+disable_xck:
+	clk_disable(clock->xck);
+err:
+	return ret;
 }
 
 static int fsi_clk_disable(struct device *dev,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/core.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/core.c
@@ -1159,6 +1159,7 @@
 		struct device_node *capture)
 {
 	struct rsnd_priv *priv = rsnd_rdai_to_priv(rdai);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct device_node *np;
 	int i;
 
@@ -1169,7 +1170,11 @@
 	for_each_child_of_node(node, np) {
 		struct rsnd_mod *mod;
 
-		i = rsnd_node_fixed_index(np, name, i);
+		i = rsnd_node_fixed_index(dev, np, name, i);
+		if (i < 0) {
+			of_node_put(np);
+			break;
+		}
 
 		mod = mod_get(priv, i);
 
@@ -1183,7 +1188,7 @@
 	of_node_put(node);
 }
 
-int rsnd_node_fixed_index(struct device_node *node, char *name, int idx)
+int rsnd_node_fixed_index(struct device *dev, struct device_node *node, char *name, int idx)
 {
 	char node_name[16];
 
@@ -1210,6 +1215,8 @@
 			return idx;
 	}
 
+	dev_err(dev, "strange node numbering (%s)",
+		of_node_full_name(node));
 	return -EINVAL;
 }
 
@@ -1221,10 +1228,9 @@
 
 	i = 0;
 	for_each_child_of_node(node, np) {
-		i = rsnd_node_fixed_index(np, name, i);
+		i = rsnd_node_fixed_index(dev, np, name, i);
 		if (i < 0) {
-			dev_err(dev, "strange node numbering (%s)",
-				of_node_full_name(node));
+			of_node_put(np);
 			return 0;
 		}
 		i++;
@@ -1688,20 +1694,6 @@
 	return 1;
 }
 
-int rsnd_kctrl_accept_runtime(struct rsnd_dai_stream *io)
-{
-	struct snd_pcm_runtime *runtime = rsnd_io_to_runtime(io);
-	struct rsnd_priv *priv = rsnd_io_to_priv(io);
-	struct device *dev = rsnd_priv_to_dev(priv);
-
-	if (!runtime) {
-		dev_warn(dev, "Can't update kctrl when idle\n");
-		return 0;
-	}
-
-	return 1;
-}
-
 struct rsnd_kctrl_cfg *rsnd_kctrl_init_m(struct rsnd_kctrl_cfg_m *cfg)
 {
 	cfg->cfg.val = cfg->val;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/ctu.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/ctu.c
@@ -171,7 +171,11 @@
 			 struct rsnd_dai_stream *io,
 			 struct rsnd_priv *priv)
 {
-	rsnd_mod_power_on(mod);
+	int ret;
+
+	ret = rsnd_mod_power_on(mod);
+	if (ret < 0)
+		return ret;
 
 	rsnd_ctu_activation(mod);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/dma.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/dma.c
@@ -102,7 +102,7 @@
 	struct rsnd_dmaen *dmaen = rsnd_dma_to_dmaen(dma);
 
 	if (dmaen->chan)
-		dmaengine_terminate_sync(dmaen->chan);
+		dmaengine_terminate_async(dmaen->chan);
 
 	return 0;
 }
@@ -240,12 +240,19 @@
 struct dma_chan *rsnd_dma_request_channel(struct device_node *of_node, char *name,
 					  struct rsnd_mod *mod, char *x)
 {
+	struct rsnd_priv *priv = rsnd_mod_to_priv(mod);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct dma_chan *chan = NULL;
 	struct device_node *np;
 	int i = 0;
 
 	for_each_child_of_node(of_node, np) {
-		i = rsnd_node_fixed_index(np, name, i);
+		i = rsnd_node_fixed_index(dev, np, name, i);
+		if (i < 0) {
+			chan = NULL;
+			of_node_put(np);
+			break;
+		}
 
 		if (i == rsnd_mod_id_raw(mod) && (!chan))
 			chan = of_dma_request_slave_channel(np, x);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/dvc.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/dvc.c
@@ -186,7 +186,11 @@
 			 struct rsnd_dai_stream *io,
 			 struct rsnd_priv *priv)
 {
-	rsnd_mod_power_on(mod);
+	int ret;
+
+	ret = rsnd_mod_power_on(mod);
+	if (ret < 0)
+		return ret;
 
 	rsnd_dvc_activation(mod);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/mix.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/mix.c
@@ -146,7 +146,11 @@
 			 struct rsnd_dai_stream *io,
 			 struct rsnd_priv *priv)
 {
-	rsnd_mod_power_on(mod);
+	int ret;
+
+	ret = rsnd_mod_power_on(mod);
+	if (ret < 0)
+		return ret;
 
 	rsnd_mix_activation(mod);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/rsnd.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/rsnd.h
@@ -460,7 +460,7 @@
 		struct device_node *playback,
 		struct device_node *capture);
 int rsnd_node_count(struct rsnd_priv *priv, struct device_node *node, char *name);
-int rsnd_node_fixed_index(struct device_node *node, char *name, int idx);
+int rsnd_node_fixed_index(struct device *dev, struct device_node *node, char *name, int idx);
 
 int rsnd_channel_normalization(int chan);
 #define rsnd_runtime_channel_original(io) \
@@ -742,7 +742,6 @@
 #define rsnd_kctrl_vals(x)	((x).val)	/* = (x).cfg.val[0] */
 
 int rsnd_kctrl_accept_anytime(struct rsnd_dai_stream *io);
-int rsnd_kctrl_accept_runtime(struct rsnd_dai_stream *io);
 struct rsnd_kctrl_cfg *rsnd_kctrl_init_m(struct rsnd_kctrl_cfg_m *cfg);
 struct rsnd_kctrl_cfg *rsnd_kctrl_init_s(struct rsnd_kctrl_cfg_s *cfg);
 int rsnd_kctrl_new(struct rsnd_mod *mod,
@@ -901,8 +900,6 @@
 	if (!IS_BUILTIN(RSND_DEBUG_NO_DAI_CALL))	\
 		dev_dbg(dev, param)
 
-#endif
-
 #ifdef CONFIG_DEBUG_FS
 int rsnd_debugfs_probe(struct snd_soc_component *component);
 void rsnd_debugfs_reg_show(struct seq_file *m, phys_addr_t _addr,
@@ -913,3 +910,5 @@
 #else
 #define rsnd_debugfs_probe  NULL
 #endif
+
+#endif /* RSND_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/src.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/src.c
@@ -463,11 +463,14 @@
 			 struct rsnd_priv *priv)
 {
 	struct rsnd_src *src = rsnd_mod_to_src(mod);
+	int ret;
 
 	/* reset sync convert_rate */
 	src->sync.val = 0;
 
-	rsnd_mod_power_on(mod);
+	ret = rsnd_mod_power_on(mod);
+	if (ret < 0)
+		return ret;
 
 	rsnd_src_activation(mod);
 
@@ -527,6 +530,22 @@
 	return IRQ_HANDLED;
 }
 
+static int rsnd_src_kctrl_accept_runtime(struct rsnd_dai_stream *io)
+{
+	struct snd_pcm_runtime *runtime = rsnd_io_to_runtime(io);
+
+	if (!runtime) {
+		struct rsnd_priv *priv = rsnd_io_to_priv(io);
+		struct device *dev = rsnd_priv_to_dev(priv);
+
+		dev_warn(dev, "\"SRC Out Rate\" can use during running\n");
+
+		return 0;
+	}
+
+	return 1;
+}
+
 static int rsnd_src_probe_(struct rsnd_mod *mod,
 			   struct rsnd_dai_stream *io,
 			   struct rsnd_priv *priv)
@@ -590,7 +609,7 @@
 			       rsnd_io_is_play(io) ?
 			       "SRC Out Rate" :
 			       "SRC In Rate",
-			       rsnd_kctrl_accept_runtime,
+			       rsnd_src_kctrl_accept_runtime,
 			       rsnd_src_set_convert_rate,
 			       &src->sync, 192000);
 
@@ -676,7 +695,12 @@
 		if (!of_device_is_available(np))
 			goto skip;
 
-		i = rsnd_node_fixed_index(np, SRC_NAME, i);
+		i = rsnd_node_fixed_index(dev, np, SRC_NAME, i);
+		if (i < 0) {
+			ret = -EINVAL;
+			of_node_put(np);
+			goto rsnd_src_probe_done;
+		}
 
 		src = rsnd_src_get(priv, i);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/ssi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/ssi.c
@@ -480,7 +480,9 @@
 
 	ssi->usrcnt++;
 
-	rsnd_mod_power_on(mod);
+	ret = rsnd_mod_power_on(mod);
+	if (ret < 0)
+		return ret;
 
 	rsnd_ssi_config_init(mod, io);
 
@@ -1105,6 +1107,7 @@
 			    struct device_node *capture)
 {
 	struct rsnd_priv *priv = rsnd_rdai_to_priv(rdai);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct device_node *node;
 	struct device_node *np;
 	int i;
@@ -1117,7 +1120,11 @@
 	for_each_child_of_node(node, np) {
 		struct rsnd_mod *mod;
 
-		i = rsnd_node_fixed_index(np, SSI_NAME, i);
+		i = rsnd_node_fixed_index(dev, np, SSI_NAME, i);
+		if (i < 0) {
+			of_node_put(np);
+			break;
+		}
 
 		mod = rsnd_ssi_mod_get(priv, i);
 
@@ -1182,7 +1189,12 @@
 		if (!of_device_is_available(np))
 			goto skip;
 
-		i = rsnd_node_fixed_index(np, SSI_NAME, i);
+		i = rsnd_node_fixed_index(dev, np, SSI_NAME, i);
+		if (i < 0) {
+			ret = -EINVAL;
+			of_node_put(np);
+			goto rsnd_ssi_probe_done;
+		}
 
 		ssi = rsnd_ssi_get(priv, i);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rcar/ssiu.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rcar/ssiu.c
@@ -67,6 +67,8 @@
 		shift  = 1;
 		offset = 1;
 		break;
+	default:
+		return;
 	}
 
 	for (i = 0; i < 4; i++) {
@@ -102,6 +104,8 @@
 		shift  = 1;
 		offset = 1;
 		break;
+	default:
+		goto out;
 	}
 
 	for (i = 0; i < 4; i++) {
@@ -120,7 +124,7 @@
 		}
 		rsnd_mod_write(mod, reg, val);
 	}
-
+out:
 	return error;
 }
 
@@ -460,6 +464,7 @@
 			     struct device_node *capture)
 {
 	struct rsnd_priv *priv = rsnd_rdai_to_priv(rdai);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct device_node *node = rsnd_ssiu_of_node(priv);
 	struct rsnd_dai_stream *io_p = &rdai->playback;
 	struct rsnd_dai_stream *io_c = &rdai->capture;
@@ -472,7 +477,11 @@
 		for_each_child_of_node(node, np) {
 			struct rsnd_mod *mod;
 
-			i = rsnd_node_fixed_index(np, SSIU_NAME, i);
+			i = rsnd_node_fixed_index(dev, np, SSIU_NAME, i);
+			if (i < 0) {
+				of_node_put(np);
+				break;
+			}
 
 			mod = rsnd_ssiu_mod_get(priv, i);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sh/rz-ssi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sh/rz-ssi.c
@@ -243,8 +243,7 @@
 static int rz_ssi_clk_setup(struct rz_ssi_priv *ssi, unsigned int rate,
 			    unsigned int channels)
 {
-	static s8 ckdv[16] = { 1,  2,  4,  8, 16, 32, 64, 128,
-			       6, 12, 24, 48, 96, -1, -1, -1 };
+	static u8 ckdv[] = { 1,  2,  4,  8, 16, 32, 64, 128, 6, 12, 24, 48, 96 };
 	unsigned int channel_bits = 32;	/* System Word Length */
 	unsigned long bclk_rate = rate * channels * channel_bits;
 	unsigned int div;
@@ -411,54 +410,56 @@
 {
 	struct snd_pcm_substream *substream = strm->substream;
 	struct snd_pcm_runtime *runtime;
+	bool done = false;
 	u16 *buf;
 	int fifo_samples;
 	int frames_left;
-	int samples = 0;
+	int samples;
 	int i;
 
 	if (!rz_ssi_stream_is_valid(ssi, strm))
 		return -EINVAL;
 
 	runtime = substream->runtime;
-	/* frames left in this period */
-	frames_left = runtime->period_size - (strm->buffer_pos %
-					      runtime->period_size);
-	if (frames_left == 0)
-		frames_left = runtime->period_size;
 
-	/* Samples in RX FIFO */
-	fifo_samples = (rz_ssi_reg_readl(ssi, SSIFSR) >>
-			SSIFSR_RDC_SHIFT) & SSIFSR_RDC_MASK;
-
-	/* Only read full frames at a time */
-	while (frames_left && (fifo_samples >= runtime->channels)) {
-		samples += runtime->channels;
-		fifo_samples -= runtime->channels;
-		frames_left--;
-	}
-
-	/* not enough samples yet */
-	if (samples == 0)
-		return 0;
+	while (!done) {
+		/* frames left in this period */
+		frames_left = runtime->period_size -
+			      (strm->buffer_pos % runtime->period_size);
+		if (!frames_left)
+			frames_left = runtime->period_size;
+
+		/* Samples in RX FIFO */
+		fifo_samples = (rz_ssi_reg_readl(ssi, SSIFSR) >>
+				SSIFSR_RDC_SHIFT) & SSIFSR_RDC_MASK;
+
+		/* Only read full frames at a time */
+		samples = 0;
+		while (frames_left && (fifo_samples >= runtime->channels)) {
+			samples += runtime->channels;
+			fifo_samples -= runtime->channels;
+			frames_left--;
+		}
 
-	/* calculate new buffer index */
-	buf = (u16 *)(runtime->dma_area);
-	buf += strm->buffer_pos * runtime->channels;
+		/* not enough samples yet */
+		if (!samples)
+			break;
 
-	/* Note, only supports 16-bit samples */
-	for (i = 0; i < samples; i++)
-		*buf++ = (u16)(rz_ssi_reg_readl(ssi, SSIFRDR) >> 16);
+		/* calculate new buffer index */
+		buf = (u16 *)(runtime->dma_area);
+		buf += strm->buffer_pos * runtime->channels;
+
+		/* Note, only supports 16-bit samples */
+		for (i = 0; i < samples; i++)
+			*buf++ = (u16)(rz_ssi_reg_readl(ssi, SSIFRDR) >> 16);
 
-	rz_ssi_reg_mask_setl(ssi, SSIFSR, SSIFSR_RDF, 0);
-	rz_ssi_pointer_update(strm, samples / runtime->channels);
+		rz_ssi_reg_mask_setl(ssi, SSIFSR, SSIFSR_RDF, 0);
+		rz_ssi_pointer_update(strm, samples / runtime->channels);
 
-	/*
-	 * If we finished this period, but there are more samples in
-	 * the RX FIFO, call this function again
-	 */
-	if (frames_left == 0 && fifo_samples >= runtime->channels)
-		rz_ssi_pio_recv(ssi, strm);
+		/* check if there are no more samples in the RX FIFO */
+		if (!(!frames_left && fifo_samples >= runtime->channels))
+			done = true;
+	}
 
 	return 0;
 }
@@ -486,6 +487,8 @@
 	sample_space = strm->fifo_sample_size;
 	ssifsr = rz_ssi_reg_readl(ssi, SSIFSR);
 	sample_space -= (ssifsr >> SSIFSR_TDC_SHIFT) & SSIFSR_TDC_MASK;
+	if (sample_space < 0)
+		return -EINVAL;
 
 	/* Only add full frames at a time */
 	while (frames_left && (sample_space >= runtime->channels)) {
@@ -975,24 +978,29 @@
 	ssi->playback.priv = ssi;
 	ssi->capture.priv = ssi;
 
+	spin_lock_init(&ssi->lock);
+	dev_set_drvdata(&pdev->dev, ssi);
+
 	/* Error Interrupt */
 	ssi->irq_int = platform_get_irq_byname(pdev, "int_req");
-	if (ssi->irq_int < 0)
-		return dev_err_probe(&pdev->dev, -ENODEV,
-				     "Unable to get SSI int_req IRQ\n");
+	if (ssi->irq_int < 0) {
+		rz_ssi_release_dma_channels(ssi);
+		return ssi->irq_int;
+	}
 
 	ret = devm_request_irq(&pdev->dev, ssi->irq_int, &rz_ssi_interrupt,
 			       0, dev_name(&pdev->dev), ssi);
-	if (ret < 0)
+	if (ret < 0) {
+		rz_ssi_release_dma_channels(ssi);
 		return dev_err_probe(&pdev->dev, ret,
 				     "irq request error (int_req)\n");
+	}
 
 	if (!rz_ssi_is_dma_enabled(ssi)) {
 		/* Tx and Rx interrupts (pio only) */
 		ssi->irq_tx = platform_get_irq_byname(pdev, "dma_tx");
 		if (ssi->irq_tx < 0)
-			return dev_err_probe(&pdev->dev, -ENODEV,
-					     "Unable to get SSI dma_tx IRQ\n");
+			return ssi->irq_tx;
 
 		ret = devm_request_irq(&pdev->dev, ssi->irq_tx,
 				       &rz_ssi_interrupt, 0,
@@ -1003,8 +1011,7 @@
 
 		ssi->irq_rx = platform_get_irq_byname(pdev, "dma_rx");
 		if (ssi->irq_rx < 0)
-			return dev_err_probe(&pdev->dev, -ENODEV,
-					     "Unable to get SSI dma_rx IRQ\n");
+			return ssi->irq_rx;
 
 		ret = devm_request_irq(&pdev->dev, ssi->irq_rx,
 				       &rz_ssi_interrupt, 0,
@@ -1015,27 +1022,37 @@
 	}
 
 	ssi->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
-	if (IS_ERR(ssi->rstc))
-		return PTR_ERR(ssi->rstc);
+	if (IS_ERR(ssi->rstc)) {
+		ret = PTR_ERR(ssi->rstc);
+		goto err_reset;
+	}
 
 	reset_control_deassert(ssi->rstc);
 	pm_runtime_enable(&pdev->dev);
-	pm_runtime_resume_and_get(&pdev->dev);
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "pm_runtime_resume_and_get failed\n");
+		goto err_pm;
+	}
 
-	spin_lock_init(&ssi->lock);
-	dev_set_drvdata(&pdev->dev, ssi);
 	ret = devm_snd_soc_register_component(&pdev->dev, &rz_ssi_soc_component,
 					      rz_ssi_soc_dai,
 					      ARRAY_SIZE(rz_ssi_soc_dai));
 	if (ret < 0) {
-		rz_ssi_release_dma_channels(ssi);
-
-		pm_runtime_put(ssi->dev);
-		pm_runtime_disable(ssi->dev);
-		reset_control_assert(ssi->rstc);
 		dev_err(&pdev->dev, "failed to register snd component\n");
+		goto err_snd_soc;
 	}
 
+	return 0;
+
+err_snd_soc:
+	pm_runtime_put(ssi->dev);
+err_pm:
+	pm_runtime_disable(ssi->dev);
+	reset_control_assert(ssi->rstc);
+err_reset:
+	rz_ssi_release_dma_channels(ssi);
+
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-compress.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-compress.c
@@ -116,6 +116,8 @@
 	if (ret < 0)
 		goto be_err;
 
+	mutex_lock_nested(&fe->card->pcm_mutex, fe->card->pcm_subclass);
+
 	/* calculate valid and active FE <-> BE dpcms */
 	dpcm_process_paths(fe, stream, &list, 1);
 	fe->dpcm[stream].runtime = fe_substream->runtime;
@@ -151,7 +153,6 @@
 	fe->dpcm[stream].state = SND_SOC_DPCM_STATE_OPEN;
 	fe->dpcm[stream].runtime_update = SND_SOC_DPCM_UPDATE_NO;
 
-	mutex_lock_nested(&fe->card->pcm_mutex, fe->card->pcm_subclass);
 	snd_soc_runtime_activate(fe, stream);
 	mutex_unlock(&fe->card->pcm_mutex);
 
@@ -182,7 +183,6 @@
 
 	mutex_lock_nested(&fe->card->pcm_mutex, fe->card->pcm_subclass);
 	snd_soc_runtime_deactivate(fe, stream);
-	mutex_unlock(&fe->card->pcm_mutex);
 
 	fe->dpcm[stream].runtime_update = SND_SOC_DPCM_UPDATE_FE;
 
@@ -201,6 +201,8 @@
 
 	dpcm_be_disconnect(fe, stream);
 
+	mutex_unlock(&fe->card->pcm_mutex);
+
 	fe->dpcm[stream].runtime = NULL;
 
 	snd_soc_link_compr_shutdown(cstream, 0);
@@ -376,8 +378,9 @@
 	ret = snd_soc_link_compr_set_params(cstream);
 	if (ret < 0)
 		goto out;
-
+	mutex_lock_nested(&fe->card->pcm_mutex, fe->card->pcm_subclass);
 	dpcm_dapm_stream_event(fe, stream, SND_SOC_DAPM_STREAM_START);
+	mutex_unlock(&fe->card->pcm_mutex);
 	fe->dpcm[stream].state = SND_SOC_DPCM_STATE_PREPARE;
 
 out:
@@ -534,6 +537,11 @@
 		return -EINVAL;
 	}
 
+	if (!codec_dai) {
+		dev_err(rtd->card->dev, "Missing codec\n");
+		return -EINVAL;
+	}
+
 	/* check client and interface hw capabilities */
 	if (snd_soc_dai_stream_valid(codec_dai, SNDRV_PCM_STREAM_PLAYBACK) &&
 	    snd_soc_dai_stream_valid(cpu_dai,   SNDRV_PCM_STREAM_PLAYBACK))
@@ -581,11 +589,14 @@
 			return ret;
 		}
 
+		/* inherit atomicity from DAI link */
+		be_pcm->nonatomic = rtd->dai_link->nonatomic;
+
 		rtd->pcm = be_pcm;
 		rtd->fe_compr = 1;
 		if (rtd->dai_link->dpcm_playback)
 			be_pcm->streams[SNDRV_PCM_STREAM_PLAYBACK].substream->private_data = rtd;
-		else if (rtd->dai_link->dpcm_capture)
+		if (rtd->dai_link->dpcm_capture)
 			be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream->private_data = rtd;
 		memcpy(compr->ops, &soc_compr_dyn_ops, sizeof(soc_compr_dyn_ops));
 	} else {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-core.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-core.c
@@ -1042,6 +1042,9 @@
 			if (!snd_soc_is_matching_component(platform, component))
 				continue;
 
+			if (snd_soc_component_is_dummy(component) && component->num_dai)
+				continue;
+
 			snd_soc_rtd_add_component(rtd, component);
 		}
 	}
@@ -2339,7 +2342,6 @@
 	mutex_init(&card->mutex);
 	mutex_init(&card->dapm_mutex);
 	mutex_init(&card->pcm_mutex);
-	spin_lock_init(&card->dpcm_lock);
 
 	return snd_soc_bind_card(card);
 }
@@ -3208,7 +3210,7 @@
 	for_each_component(pos) {
 		struct device_node *component_of_node = soc_component_to_node(pos);
 
-		if (component_of_node != args->np)
+		if (component_of_node != args->np || !pos->num_dai)
 			continue;
 
 		ret = snd_soc_component_of_xlate_dai_name(pos, args, dai_name);
@@ -3366,10 +3368,23 @@
 
 static int __init snd_soc_init(void)
 {
+	int ret;
+
 	snd_soc_debugfs_init();
-	snd_soc_util_init();
+	ret = snd_soc_util_init();
+	if (ret)
+		goto err_util_init;
 
-	return platform_driver_register(&soc_driver);
+	ret = platform_driver_register(&soc_driver);
+	if (ret)
+		goto err_register;
+	return 0;
+
+err_register:
+	snd_soc_util_exit();
+err_util_init:
+	snd_soc_debugfs_exit();
+	return ret;
 }
 module_init(snd_soc_init);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-dapm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-dapm.c
@@ -62,6 +62,8 @@
 snd_soc_dapm_new_control_unlocked(struct snd_soc_dapm_context *dapm,
 			 const struct snd_soc_dapm_widget *widget);
 
+static unsigned int soc_dapm_read(struct snd_soc_dapm_context *dapm, int reg);
+
 /* dapm power sequences - make this per codec in the future */
 static int dapm_up_seq[] = {
 	[snd_soc_dapm_pre] = 1,
@@ -442,6 +444,9 @@
 
 			snd_soc_dapm_add_path(widget->dapm, data->widget,
 					      widget, NULL, NULL);
+		} else if (e->reg != SND_SOC_NOPM) {
+			data->value = soc_dapm_read(widget->dapm, e->reg) &
+				      (e->mask << e->shift_l);
 		}
 		break;
 	default:
@@ -1685,8 +1690,7 @@
 		switch (w->id) {
 		case snd_soc_dapm_pre:
 			if (!w->event)
-				list_for_each_entry_safe_continue(w, n, list,
-								  power_list);
+				continue;
 
 			if (event == SND_SOC_DAPM_STREAM_START)
 				ret = w->event(w,
@@ -1698,8 +1702,7 @@
 
 		case snd_soc_dapm_post:
 			if (!w->event)
-				list_for_each_entry_safe_continue(w, n, list,
-								  power_list);
+				continue;
 
 			if (event == SND_SOC_DAPM_STREAM_START)
 				ret = w->event(w,
@@ -2557,8 +2560,13 @@
 	return NULL;
 }
 
-static int snd_soc_dapm_set_pin(struct snd_soc_dapm_context *dapm,
-				const char *pin, int status)
+/*
+ * set the DAPM pin status:
+ * returns 1 when the value has been updated, 0 when unchanged, or a negative
+ * error code; called from kcontrol put callback
+ */
+static int __snd_soc_dapm_set_pin(struct snd_soc_dapm_context *dapm,
+				  const char *pin, int status)
 {
 	struct snd_soc_dapm_widget *w = dapm_find_widget(dapm, pin, true);
 	int ret = 0;
@@ -2584,6 +2592,18 @@
 	return ret;
 }
 
+/*
+ * similar as __snd_soc_dapm_set_pin(), but returns 0 when successful;
+ * called from several API functions below
+ */
+static int snd_soc_dapm_set_pin(struct snd_soc_dapm_context *dapm,
+				const char *pin, int status)
+{
+	int ret = __snd_soc_dapm_set_pin(dapm, pin, status);
+
+	return ret < 0 ? ret : 0;
+}
+
 /**
  * snd_soc_dapm_sync_unlocked - scan and power dapm paths
  * @dapm: DAPM context
@@ -3413,7 +3433,6 @@
 			update.val = val;
 			card->update = &update;
 		}
-		change |= reg_change;
 
 		ret = soc_dapm_mixer_update_power(card, kcontrol, connect,
 						  rconnect);
@@ -3515,7 +3534,6 @@
 			update.val = val;
 			card->update = &update;
 		}
-		change |= reg_change;
 
 		ret = soc_dapm_mux_update_power(card, kcontrol, item[0], e);
 
@@ -3587,10 +3605,10 @@
 	const char *pin = (const char *)kcontrol->private_value;
 	int ret;
 
-	if (ucontrol->value.integer.value[0])
-		ret = snd_soc_dapm_enable_pin(&card->dapm, pin);
-	else
-		ret = snd_soc_dapm_disable_pin(&card->dapm, pin);
+	mutex_lock_nested(&card->dapm_mutex, SND_SOC_DAPM_CLASS_RUNTIME);
+	ret = __snd_soc_dapm_set_pin(&card->dapm, pin,
+				     !!ucontrol->value.integer.value[0]);
+	mutex_unlock(&card->dapm_mutex);
 
 	snd_soc_dapm_sync(&card->dapm);
 	return ret;
@@ -3984,6 +4002,7 @@
 
 	case SND_SOC_DAPM_POST_PMD:
 		kfree(substream->runtime);
+		substream->runtime = NULL;
 		break;
 
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-generic-dmaengine-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-generic-dmaengine-pcm.c
@@ -323,6 +323,12 @@
 	return 0;
 }
 
+static int dmaengine_pcm_sync_stop(struct snd_soc_component *component,
+				   struct snd_pcm_substream *substream)
+{
+	return snd_dmaengine_pcm_sync_stop(substream);
+}
+
 static const struct snd_soc_component_driver dmaengine_pcm_component = {
 	.name		= SND_DMAENGINE_PCM_DRV_NAME,
 	.probe_order	= SND_SOC_COMP_ORDER_LATE,
@@ -332,6 +338,7 @@
 	.trigger	= dmaengine_pcm_trigger,
 	.pointer	= dmaengine_pcm_pointer,
 	.pcm_construct	= dmaengine_pcm_new,
+	.sync_stop	= dmaengine_pcm_sync_stop,
 };
 
 static const struct snd_soc_component_driver dmaengine_pcm_component_process = {
@@ -344,6 +351,7 @@
 	.pointer	= dmaengine_pcm_pointer,
 	.copy_user	= dmaengine_copy_user,
 	.pcm_construct	= dmaengine_pcm_new,
+	.sync_stop	= dmaengine_pcm_sync_stop,
 };
 
 static const char * const dmaengine_pcm_dma_channel_names[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-ops.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-ops.c
@@ -246,7 +246,7 @@
 	int max = mc->max;
 	int min = mc->min;
 	int sign_bit = mc->sign_bit;
-	unsigned int mask = (1 << fls(max)) - 1;
+	unsigned int mask = (1ULL << fls(max)) - 1;
 	unsigned int invert = mc->invert;
 	int val;
 	int ret;
@@ -308,7 +308,7 @@
 	unsigned int sign_bit = mc->sign_bit;
 	unsigned int mask = (1 << fls(max)) - 1;
 	unsigned int invert = mc->invert;
-	int err;
+	int err, ret;
 	bool type_2r = false;
 	unsigned int val2 = 0;
 	unsigned int val, val_mask;
@@ -316,13 +316,27 @@
 	if (sign_bit)
 		mask = BIT(sign_bit + 1) - 1;
 
-	val = ((ucontrol->value.integer.value[0] + min) & mask);
+	val = ucontrol->value.integer.value[0];
+	if (mc->platform_max && val > mc->platform_max)
+		return -EINVAL;
+	if (val > max - min)
+		return -EINVAL;
+	if (val < 0)
+		return -EINVAL;
+	val = (val + min) & mask;
 	if (invert)
 		val = max - val;
 	val_mask = mask << shift;
 	val = val << shift;
 	if (snd_soc_volsw_is_stereo(mc)) {
-		val2 = ((ucontrol->value.integer.value[1] + min) & mask);
+		val2 = ucontrol->value.integer.value[1];
+		if (mc->platform_max && val2 > mc->platform_max)
+			return -EINVAL;
+		if (val2 > max - min)
+			return -EINVAL;
+		if (val2 < 0)
+			return -EINVAL;
+		val2 = (val2 + min) & mask;
 		if (invert)
 			val2 = max - val2;
 		if (reg == reg2) {
@@ -336,12 +350,18 @@
 	err = snd_soc_component_update_bits(component, reg, val_mask, val);
 	if (err < 0)
 		return err;
+	ret = err;
 
-	if (type_2r)
+	if (type_2r) {
 		err = snd_soc_component_update_bits(component, reg2, val_mask,
-			val2);
+						    val2);
+		/* Don't discard any error code or drop change flag */
+		if (ret == 0 || err < 0) {
+			ret = err;
+		}
+	}
 
-	return err;
+	return ret;
 }
 EXPORT_SYMBOL_GPL(snd_soc_put_volsw);
 
@@ -407,27 +427,46 @@
 	int min = mc->min;
 	unsigned int mask = (1U << (fls(min + max) - 1)) - 1;
 	int err = 0;
+	int ret;
 	unsigned int val, val_mask;
 
+	val = ucontrol->value.integer.value[0];
+	if (mc->platform_max && val > mc->platform_max)
+		return -EINVAL;
+	if (val > max)
+		return -EINVAL;
+	if (val < 0)
+		return -EINVAL;
 	val_mask = mask << shift;
-	val = (ucontrol->value.integer.value[0] + min) & mask;
+	val = (val + min) & mask;
 	val = val << shift;
 
 	err = snd_soc_component_update_bits(component, reg, val_mask, val);
 	if (err < 0)
 		return err;
+	ret = err;
 
 	if (snd_soc_volsw_is_stereo(mc)) {
-		unsigned int val2;
+		unsigned int val2 = ucontrol->value.integer.value[1];
+
+		if (mc->platform_max && val2 > mc->platform_max)
+			return -EINVAL;
+		if (val2 > max)
+			return -EINVAL;
 
 		val_mask = mask << rshift;
-		val2 = (ucontrol->value.integer.value[1] + min) & mask;
+		val2 = (val2 + min) & mask;
 		val2 = val2 << rshift;
 
 		err = snd_soc_component_update_bits(component, reg2, val_mask,
 			val2);
+
+		/* Don't discard any error code or drop change flag */
+		if (ret == 0 || err < 0) {
+			ret = err;
+		}
 	}
-	return err;
+	return ret;
 }
 EXPORT_SYMBOL_GPL(snd_soc_put_volsw_sx);
 
@@ -446,17 +485,16 @@
 {
 	struct soc_mixer_control *mc =
 		(struct soc_mixer_control *)kcontrol->private_value;
-	int platform_max;
-	int min = mc->min;
+	int max;
 
-	if (!mc->platform_max)
-		mc->platform_max = mc->max;
-	platform_max = mc->platform_max;
+	max = mc->max - mc->min;
+	if (mc->platform_max && mc->platform_max < max)
+		max = mc->platform_max;
 
 	uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
 	uinfo->count = snd_soc_volsw_is_stereo(mc) ? 2 : 1;
 	uinfo->value.integer.min = 0;
-	uinfo->value.integer.max = platform_max - min;
+	uinfo->value.integer.max = max;
 
 	return 0;
 }
@@ -485,7 +523,15 @@
 	unsigned int mask = (1 << fls(max)) - 1;
 	unsigned int invert = mc->invert;
 	unsigned int val, val_mask;
-	int ret;
+	int err, ret, tmp;
+
+	tmp = ucontrol->value.integer.value[0];
+	if (tmp < 0)
+		return -EINVAL;
+	if (mc->platform_max && tmp > mc->platform_max)
+		return -EINVAL;
+	if (tmp > mc->max - mc->min)
+		return -EINVAL;
 
 	if (invert)
 		val = (max - ucontrol->value.integer.value[0]) & mask;
@@ -494,11 +540,20 @@
 	val_mask = mask << shift;
 	val = val << shift;
 
-	ret = snd_soc_component_update_bits(component, reg, val_mask, val);
-	if (ret < 0)
-		return ret;
+	err = snd_soc_component_update_bits(component, reg, val_mask, val);
+	if (err < 0)
+		return err;
+	ret = err;
 
 	if (snd_soc_volsw_is_stereo(mc)) {
+		tmp = ucontrol->value.integer.value[1];
+		if (tmp < 0)
+			return -EINVAL;
+		if (mc->platform_max && tmp > mc->platform_max)
+			return -EINVAL;
+		if (tmp > mc->max - mc->min)
+			return -EINVAL;
+
 		if (invert)
 			val = (max - ucontrol->value.integer.value[1]) & mask;
 		else
@@ -506,8 +561,12 @@
 		val_mask = mask << shift;
 		val = val << shift;
 
-		ret = snd_soc_component_update_bits(component, rreg, val_mask,
+		err = snd_soc_component_update_bits(component, rreg, val_mask,
 			val);
+		/* Don't discard any error code or drop change flag */
+		if (ret == 0 || err < 0) {
+			ret = err;
+		}
 	}
 
 	return ret;
@@ -584,7 +643,7 @@
 	kctl = snd_soc_card_get_kcontrol(card, name);
 	if (kctl) {
 		struct soc_mixer_control *mc = (struct soc_mixer_control *)kctl->private_value;
-		if (max <= mc->max) {
+		if (max <= mc->max - mc->min) {
 			mc->platform_max = max;
 			ret = 0;
 		}
@@ -856,8 +915,11 @@
 	unsigned long mask = (1UL<<mc->nbits)-1;
 	long max = mc->max;
 	long val = ucontrol->value.integer.value[0];
+	int ret = 0;
 	unsigned int i;
 
+	if (val < mc->min || val > mc->max)
+		return -EINVAL;
 	if (invert)
 		val = max - val;
 	val &= mask;
@@ -868,9 +930,11 @@
 							regmask, regval);
 		if (err < 0)
 			return err;
+		if (err > 0)
+			ret = err;
 	}
 
-	return 0;
+	return ret;
 }
 EXPORT_SYMBOL_GPL(snd_soc_put_xr_sx);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-pcm.c
@@ -27,6 +27,37 @@
 #include <sound/soc-link.h>
 #include <sound/initval.h>
 
+static inline void snd_soc_dpcm_mutex_lock(struct snd_soc_pcm_runtime *rtd)
+{
+	mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
+}
+
+static inline void snd_soc_dpcm_mutex_unlock(struct snd_soc_pcm_runtime *rtd)
+{
+	mutex_unlock(&rtd->card->pcm_mutex);
+}
+
+#define snd_soc_dpcm_mutex_assert_held(rtd) \
+	lockdep_assert_held(&(rtd)->card->pcm_mutex)
+
+static inline void snd_soc_dpcm_stream_lock_irq(struct snd_soc_pcm_runtime *rtd,
+						int stream)
+{
+	snd_pcm_stream_lock_irq(snd_soc_dpcm_get_substream(rtd, stream));
+}
+
+#define snd_soc_dpcm_stream_lock_irqsave_nested(rtd, stream, flags) \
+	snd_pcm_stream_lock_irqsave_nested(snd_soc_dpcm_get_substream(rtd, stream), flags)
+
+static inline void snd_soc_dpcm_stream_unlock_irq(struct snd_soc_pcm_runtime *rtd,
+						  int stream)
+{
+	snd_pcm_stream_unlock_irq(snd_soc_dpcm_get_substream(rtd, stream));
+}
+
+#define snd_soc_dpcm_stream_unlock_irqrestore(rtd, stream, flags) \
+	snd_pcm_stream_unlock_irqrestore(snd_soc_dpcm_get_substream(rtd, stream), flags)
+
 #define DPCM_MAX_BE_USERS	8
 
 static inline const char *soc_cpu_dai_name(struct snd_soc_pcm_runtime *rtd)
@@ -73,7 +104,6 @@
 	struct snd_pcm_hw_params *params = &fe->dpcm[stream].hw_params;
 	struct snd_soc_dpcm *dpcm;
 	ssize_t offset = 0;
-	unsigned long flags;
 
 	/* FE state */
 	offset += scnprintf(buf + offset, size - offset,
@@ -101,7 +131,6 @@
 		goto out;
 	}
 
-	spin_lock_irqsave(&fe->card->dpcm_lock, flags);
 	for_each_dpcm_be(fe, stream, dpcm) {
 		struct snd_soc_pcm_runtime *be = dpcm->be;
 		params = &dpcm->hw_params;
@@ -122,7 +151,6 @@
 					   params_channels(params),
 					   params_rate(params));
 	}
-	spin_unlock_irqrestore(&fe->card->dpcm_lock, flags);
 out:
 	return offset;
 }
@@ -145,11 +173,13 @@
 	if (!buf)
 		return -ENOMEM;
 
+	snd_soc_dpcm_mutex_lock(fe);
 	for_each_pcm_streams(stream)
 		if (snd_soc_dai_stream_valid(asoc_rtd_to_cpu(fe, 0), stream))
 			offset += dpcm_show_state(fe, stream,
 						  buf + offset,
 						  out_count - offset);
+	snd_soc_dpcm_mutex_unlock(fe);
 
 	ret = simple_read_from_buffer(user_buf, count, ppos, buf, offset);
 
@@ -221,14 +251,14 @@
 	struct snd_pcm_substream *substream =
 		snd_soc_dpcm_get_substream(fe, stream);
 
-	snd_pcm_stream_lock_irq(substream);
+	snd_soc_dpcm_stream_lock_irq(fe, stream);
 	if (state == SND_SOC_DPCM_UPDATE_NO && fe->dpcm[stream].trigger_pending) {
 		dpcm_fe_dai_do_trigger(substream,
 				       fe->dpcm[stream].trigger_pending - 1);
 		fe->dpcm[stream].trigger_pending = 0;
 	}
 	fe->dpcm[stream].runtime_update = state;
-	snd_pcm_stream_unlock_irq(substream);
+	snd_soc_dpcm_stream_unlock_irq(fe, stream);
 }
 
 static void dpcm_set_be_update_state(struct snd_soc_pcm_runtime *be,
@@ -256,7 +286,7 @@
 	struct snd_soc_dai *dai;
 	int i;
 
-	lockdep_assert_held(&rtd->card->pcm_mutex);
+	snd_soc_dpcm_mutex_assert_held(rtd);
 
 	for_each_rtd_dais(rtd, i, dai)
 		snd_soc_dai_action(dai, stream, action);
@@ -309,6 +339,8 @@
 {
 	struct snd_soc_dpcm *dpcm;
 
+	snd_soc_dpcm_mutex_assert_held(fe);
+
 	for_each_dpcm_be(fe, dir, dpcm) {
 
 		struct snd_soc_pcm_runtime *be = dpcm->be;
@@ -646,14 +678,14 @@
 	return ret;
 }
 
-static int soc_pcm_clean(struct snd_pcm_substream *substream, int rollback)
+static int soc_pcm_clean(struct snd_soc_pcm_runtime *rtd,
+			 struct snd_pcm_substream *substream, int rollback)
 {
-	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
 	struct snd_soc_component *component;
 	struct snd_soc_dai *dai;
 	int i;
 
-	mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
+	snd_soc_dpcm_mutex_assert_held(rtd);
 
 	if (!rollback)
 		snd_soc_runtime_deactivate(rtd, substream->stream);
@@ -665,9 +697,6 @@
 
 	soc_pcm_components_close(substream, rollback);
 
-
-	mutex_unlock(&rtd->card->pcm_mutex);
-
 	snd_soc_pcm_component_pm_runtime_put(rtd, substream, rollback);
 
 	for_each_rtd_components(rtd, i, component)
@@ -682,9 +711,21 @@
  * freed here. The cpu DAI, codec DAI, machine and components are also
  * shutdown.
  */
+static int __soc_pcm_close(struct snd_soc_pcm_runtime *rtd,
+			   struct snd_pcm_substream *substream)
+{
+	return soc_pcm_clean(rtd, substream, 0);
+}
+
+/* PCM close ops for non-DPCM streams */
 static int soc_pcm_close(struct snd_pcm_substream *substream)
 {
-	return soc_pcm_clean(substream, 0);
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+
+	snd_soc_dpcm_mutex_lock(rtd);
+	__soc_pcm_close(rtd, substream);
+	snd_soc_dpcm_mutex_unlock(rtd);
+	return 0;
 }
 
 static int soc_hw_sanity_check(struct snd_pcm_substream *substream)
@@ -730,21 +771,21 @@
  * then initialized and any private data can be allocated. This also calls
  * startup for the cpu DAI, component, machine and codec DAI.
  */
-static int soc_pcm_open(struct snd_pcm_substream *substream)
+static int __soc_pcm_open(struct snd_soc_pcm_runtime *rtd,
+			  struct snd_pcm_substream *substream)
 {
-	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
 	struct snd_soc_component *component;
 	struct snd_soc_dai *dai;
 	int i, ret = 0;
 
+	snd_soc_dpcm_mutex_assert_held(rtd);
+
 	for_each_rtd_components(rtd, i, component)
 		pinctrl_pm_select_default_state(component->dev);
 
 	ret = snd_soc_pcm_component_pm_runtime_get(rtd, substream);
 	if (ret < 0)
-		goto pm_err;
-
-	mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
+		goto err;
 
 	ret = soc_pcm_components_open(substream);
 	if (ret < 0)
@@ -791,16 +832,26 @@
 	snd_soc_runtime_activate(rtd, substream->stream);
 	ret = 0;
 err:
-	mutex_unlock(&rtd->card->pcm_mutex);
-pm_err:
 	if (ret < 0) {
-		soc_pcm_clean(substream, 1);
+		soc_pcm_clean(rtd, substream, 1);
 		dev_err(rtd->dev, "%s() failed (%d)", __func__, ret);
 	}
 
 	return ret;
 }
 
+/* PCM open ops for non-DPCM streams */
+static int soc_pcm_open(struct snd_pcm_substream *substream)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	int ret;
+
+	snd_soc_dpcm_mutex_lock(rtd);
+	ret = __soc_pcm_open(rtd, substream);
+	snd_soc_dpcm_mutex_unlock(rtd);
+	return ret;
+}
+
 static void codec2codec_close_delayed_work(struct snd_soc_pcm_runtime *rtd)
 {
 	/*
@@ -816,13 +867,13 @@
  * rate, etc.  This function is non atomic and can be called multiple times,
  * it can refer to the runtime info.
  */
-static int soc_pcm_prepare(struct snd_pcm_substream *substream)
+static int __soc_pcm_prepare(struct snd_soc_pcm_runtime *rtd,
+			     struct snd_pcm_substream *substream)
 {
-	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
 	struct snd_soc_dai *dai;
 	int i, ret = 0;
 
-	mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
+	snd_soc_dpcm_mutex_assert_held(rtd);
 
 	ret = snd_soc_link_prepare(substream);
 	if (ret < 0)
@@ -850,14 +901,24 @@
 		snd_soc_dai_digital_mute(dai, 0, substream->stream);
 
 out:
-	mutex_unlock(&rtd->card->pcm_mutex);
-
 	if (ret < 0)
 		dev_err(rtd->dev, "ASoC: %s() failed (%d)\n", __func__, ret);
 
 	return ret;
 }
 
+/* PCM prepare ops for non-DPCM streams */
+static int soc_pcm_prepare(struct snd_pcm_substream *substream)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	int ret;
+
+	snd_soc_dpcm_mutex_lock(rtd);
+	ret = __soc_pcm_prepare(rtd, substream);
+	snd_soc_dpcm_mutex_unlock(rtd);
+	return ret;
+}
+
 static void soc_pcm_codec_params_fixup(struct snd_pcm_hw_params *params,
 				       unsigned int mask)
 {
@@ -869,13 +930,13 @@
 	interval->max = channels;
 }
 
-static int soc_pcm_hw_clean(struct snd_pcm_substream *substream, int rollback)
+static int soc_pcm_hw_clean(struct snd_soc_pcm_runtime *rtd,
+			    struct snd_pcm_substream *substream, int rollback)
 {
-	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
 	struct snd_soc_dai *dai;
 	int i;
 
-	mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
+	snd_soc_dpcm_mutex_assert_held(rtd);
 
 	/* clear the corresponding DAIs parameters when going to be inactive */
 	for_each_rtd_dais(rtd, i, dai) {
@@ -905,16 +966,28 @@
 		snd_soc_dai_hw_free(dai, substream, rollback);
 	}
 
-	mutex_unlock(&rtd->card->pcm_mutex);
 	return 0;
 }
 
 /*
  * Frees resources allocated by hw_params, can be called multiple times
  */
+static int __soc_pcm_hw_free(struct snd_soc_pcm_runtime *rtd,
+			     struct snd_pcm_substream *substream)
+{
+	return soc_pcm_hw_clean(rtd, substream, 0);
+}
+
+/* hw_free PCM ops for non-DPCM streams */
 static int soc_pcm_hw_free(struct snd_pcm_substream *substream)
 {
-	return soc_pcm_hw_clean(substream, 0);
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	int ret;
+
+	snd_soc_dpcm_mutex_lock(rtd);
+	ret = __soc_pcm_hw_free(rtd, substream);
+	snd_soc_dpcm_mutex_unlock(rtd);
+	return ret;
 }
 
 /*
@@ -922,15 +995,15 @@
  * function can also be called multiple times and can allocate buffers
  * (using snd_pcm_lib_* ). It's non-atomic.
  */
-static int soc_pcm_hw_params(struct snd_pcm_substream *substream,
-				struct snd_pcm_hw_params *params)
+static int __soc_pcm_hw_params(struct snd_soc_pcm_runtime *rtd,
+			       struct snd_pcm_substream *substream,
+			       struct snd_pcm_hw_params *params)
 {
-	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
 	struct snd_soc_dai *cpu_dai;
 	struct snd_soc_dai *codec_dai;
 	int i, ret = 0;
 
-	mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
+	snd_soc_dpcm_mutex_assert_held(rtd);
 
 	ret = soc_pcm_params_symmetry(substream, params);
 	if (ret)
@@ -1002,16 +1075,27 @@
 
 	ret = snd_soc_pcm_component_hw_params(substream, params);
 out:
-	mutex_unlock(&rtd->card->pcm_mutex);
-
 	if (ret < 0) {
-		soc_pcm_hw_clean(substream, 1);
+		soc_pcm_hw_clean(rtd, substream, 1);
 		dev_err(rtd->dev, "ASoC: %s() failed (%d)\n", __func__, ret);
 	}
 
 	return ret;
 }
 
+/* hw_params PCM ops for non-DPCM streams */
+static int soc_pcm_hw_params(struct snd_pcm_substream *substream,
+			     struct snd_pcm_hw_params *params)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	int ret;
+
+	snd_soc_dpcm_mutex_lock(rtd);
+	ret = __soc_pcm_hw_params(rtd, substream, params);
+	snd_soc_dpcm_mutex_unlock(rtd);
+	return ret;
+}
+
 static int soc_pcm_trigger(struct snd_pcm_substream *substream, int cmd)
 {
 	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
@@ -1128,8 +1212,11 @@
 static int dpcm_be_connect(struct snd_soc_pcm_runtime *fe,
 		struct snd_soc_pcm_runtime *be, int stream)
 {
+	struct snd_pcm_substream *fe_substream;
+	struct snd_pcm_substream *be_substream;
 	struct snd_soc_dpcm *dpcm;
-	unsigned long flags;
+
+	snd_soc_dpcm_mutex_assert_held(fe);
 
 	/* only add new dpcms */
 	for_each_dpcm_be(fe, stream, dpcm) {
@@ -1137,7 +1224,21 @@
 			return 0;
 	}
 
-	dpcm = kzalloc(sizeof(struct snd_soc_dpcm), GFP_KERNEL);
+	fe_substream = snd_soc_dpcm_get_substream(fe, stream);
+	be_substream = snd_soc_dpcm_get_substream(be, stream);
+
+	if (!fe_substream->pcm->nonatomic && be_substream->pcm->nonatomic) {
+		dev_err(be->dev, "%s: FE is atomic but BE is nonatomic, invalid configuration\n",
+			__func__);
+		return -EINVAL;
+	}
+	if (fe_substream->pcm->nonatomic && !be_substream->pcm->nonatomic) {
+		dev_warn(be->dev, "%s: FE is nonatomic but BE is not, forcing BE as nonatomic\n",
+			 __func__);
+		be_substream->pcm->nonatomic = 1;
+	}
+
+	dpcm = kzalloc(sizeof(struct snd_soc_dpcm), GFP_ATOMIC);
 	if (!dpcm)
 		return -ENOMEM;
 
@@ -1145,10 +1246,10 @@
 	dpcm->fe = fe;
 	be->dpcm[stream].runtime = fe->dpcm[stream].runtime;
 	dpcm->state = SND_SOC_DPCM_LINK_STATE_NEW;
-	spin_lock_irqsave(&fe->card->dpcm_lock, flags);
+	snd_soc_dpcm_stream_lock_irq(fe, stream);
 	list_add(&dpcm->list_be, &fe->dpcm[stream].be_clients);
 	list_add(&dpcm->list_fe, &be->dpcm[stream].fe_clients);
-	spin_unlock_irqrestore(&fe->card->dpcm_lock, flags);
+	snd_soc_dpcm_stream_unlock_irq(fe, stream);
 
 	dev_dbg(fe->dev, "connected new DPCM %s path %s %s %s\n",
 			stream ? "capture" : "playback",  fe->dai_link->name,
@@ -1171,6 +1272,8 @@
 		return;
 
 	be_substream = snd_soc_dpcm_get_substream(be, stream);
+	if (!be_substream)
+		return;
 
 	for_each_dpcm_fe(be, stream, dpcm) {
 		if (dpcm->fe == fe)
@@ -1191,8 +1294,11 @@
 void dpcm_be_disconnect(struct snd_soc_pcm_runtime *fe, int stream)
 {
 	struct snd_soc_dpcm *dpcm, *d;
-	unsigned long flags;
+	LIST_HEAD(deleted_dpcms);
 
+	snd_soc_dpcm_mutex_assert_held(fe);
+
+	snd_soc_dpcm_stream_lock_irq(fe, stream);
 	for_each_dpcm_be_safe(fe, stream, dpcm, d) {
 		dev_dbg(fe->dev, "ASoC: BE %s disconnect check for %s\n",
 				stream ? "capture" : "playback",
@@ -1208,12 +1314,16 @@
 		/* BEs still alive need new FE */
 		dpcm_be_reparent(fe, dpcm->be, stream);
 
-		dpcm_remove_debugfs_state(dpcm);
-
-		spin_lock_irqsave(&fe->card->dpcm_lock, flags);
 		list_del(&dpcm->list_be);
+		list_move(&dpcm->list_fe, &deleted_dpcms);
+	}
+	snd_soc_dpcm_stream_unlock_irq(fe, stream);
+
+	while (!list_empty(&deleted_dpcms)) {
+		dpcm = list_first_entry(&deleted_dpcms, struct snd_soc_dpcm,
+					list_fe);
 		list_del(&dpcm->list_fe);
-		spin_unlock_irqrestore(&fe->card->dpcm_lock, flags);
+		dpcm_remove_debugfs_state(dpcm);
 		kfree(dpcm);
 	}
 }
@@ -1234,6 +1344,9 @@
 		if (!be->dai_link->no_pcm)
 			continue;
 
+		if (!snd_soc_dpcm_get_substream(be, stream))
+			continue;
+
 		for_each_rtd_dais(be, i, dai) {
 			w = snd_soc_dai_get_widget(dai, stream);
 
@@ -1429,12 +1542,9 @@
 void dpcm_clear_pending_state(struct snd_soc_pcm_runtime *fe, int stream)
 {
 	struct snd_soc_dpcm *dpcm;
-	unsigned long flags;
 
-	spin_lock_irqsave(&fe->card->dpcm_lock, flags);
 	for_each_dpcm_be(fe, stream, dpcm)
 		dpcm_set_be_update_state(dpcm->be, stream, SND_SOC_DPCM_UPDATE_NO);
-	spin_unlock_irqrestore(&fe->card->dpcm_lock, flags);
 }
 
 void dpcm_be_dai_stop(struct snd_soc_pcm_runtime *fe, int stream,
@@ -1470,12 +1580,12 @@
 				continue;
 
 			if (be->dpcm[stream].state != SND_SOC_DPCM_STATE_HW_FREE) {
-				soc_pcm_hw_free(be_substream);
+				__soc_pcm_hw_free(be, be_substream);
 				be->dpcm[stream].state = SND_SOC_DPCM_STATE_HW_FREE;
 			}
 		}
 
-		soc_pcm_close(be_substream);
+		__soc_pcm_close(be, be_substream);
 		be_substream->runtime = NULL;
 		be->dpcm[stream].state = SND_SOC_DPCM_STATE_CLOSE;
 	}
@@ -1523,7 +1633,7 @@
 			stream ? "capture" : "playback", be->dai_link->name);
 
 		be_substream->runtime = be->dpcm[stream].runtime;
-		err = soc_pcm_open(be_substream);
+		err = __soc_pcm_open(be, be_substream);
 		if (err < 0) {
 			be->dpcm[stream].users--;
 			if (be->dpcm[stream].users < 0)
@@ -1534,7 +1644,7 @@
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_CLOSE;
 			goto unwind;
 		}
-
+		be->dpcm[stream].be_start = 0;
 		be->dpcm[stream].state = SND_SOC_DPCM_STATE_OPEN;
 		count++;
 	}
@@ -1557,10 +1667,14 @@
 	struct snd_pcm_hardware *hw = &runtime->hw;
 	struct snd_soc_dai *dai;
 	int stream = substream->stream;
+	u64 formats = hw->formats;
 	int i;
 
 	soc_pcm_hw_init(hw);
 
+	if (formats)
+		hw->formats &= formats;
+
 	for_each_rtd_cpu_dais(fe, i, dai) {
 		struct snd_soc_pcm_stream *cpu_stream;
 
@@ -1767,7 +1881,7 @@
 	dev_dbg(fe->dev, "ASoC: open FE %s\n", fe->dai_link->name);
 
 	/* start the DAI frontend */
-	ret = soc_pcm_open(fe_substream);
+	ret = __soc_pcm_open(fe, fe_substream);
 	if (ret < 0)
 		goto unwind;
 
@@ -1798,6 +1912,8 @@
 	struct snd_soc_pcm_runtime *fe = asoc_substream_to_rtd(substream);
 	int stream = substream->stream;
 
+	snd_soc_dpcm_mutex_assert_held(fe);
+
 	dpcm_set_fe_update_state(fe, stream, SND_SOC_DPCM_UPDATE_FE);
 
 	/* shutdown the BEs */
@@ -1806,7 +1922,7 @@
 	dev_dbg(fe->dev, "ASoC: close FE %s\n", fe->dai_link->name);
 
 	/* now shutdown the frontend */
-	soc_pcm_close(substream);
+	__soc_pcm_close(fe, substream);
 
 	/* run the stream stop event */
 	dpcm_dapm_stream_event(fe, stream, SND_SOC_DAPM_STREAM_STOP);
@@ -1851,7 +1967,7 @@
 		dev_dbg(be->dev, "ASoC: hw_free BE %s\n",
 			be->dai_link->name);
 
-		soc_pcm_hw_free(be_substream);
+		__soc_pcm_hw_free(be, be_substream);
 
 		be->dpcm[stream].state = SND_SOC_DPCM_STATE_HW_FREE;
 	}
@@ -1862,13 +1978,13 @@
 	struct snd_soc_pcm_runtime *fe = asoc_substream_to_rtd(substream);
 	int stream = substream->stream;
 
-	mutex_lock_nested(&fe->card->mutex, SND_SOC_CARD_CLASS_RUNTIME);
+	snd_soc_dpcm_mutex_lock(fe);
 	dpcm_set_fe_update_state(fe, stream, SND_SOC_DPCM_UPDATE_FE);
 
 	dev_dbg(fe->dev, "ASoC: hw_free FE %s\n", fe->dai_link->name);
 
 	/* call hw_free on the frontend */
-	soc_pcm_hw_free(substream);
+	soc_pcm_hw_clean(fe, substream, 0);
 
 	/* only hw_params backends that are either sinks or sources
 	 * to this frontend DAI */
@@ -1877,7 +1993,7 @@
 	fe->dpcm[stream].state = SND_SOC_DPCM_STATE_HW_FREE;
 	dpcm_set_fe_update_state(fe, stream, SND_SOC_DPCM_UPDATE_NO);
 
-	mutex_unlock(&fe->card->mutex);
+	snd_soc_dpcm_mutex_unlock(fe);
 	return 0;
 }
 
@@ -1921,7 +2037,7 @@
 		dev_dbg(be->dev, "ASoC: hw_params BE %s\n",
 			be->dai_link->name);
 
-		ret = soc_pcm_hw_params(be_substream, &dpcm->hw_params);
+		ret = __soc_pcm_hw_params(be, be_substream, &dpcm->hw_params);
 		if (ret < 0)
 			goto unwind;
 
@@ -1951,7 +2067,7 @@
 		   (be->dpcm[stream].state != SND_SOC_DPCM_STATE_STOP))
 			continue;
 
-		soc_pcm_hw_free(be_substream);
+		__soc_pcm_hw_free(be, be_substream);
 	}
 
 	return ret;
@@ -1963,7 +2079,7 @@
 	struct snd_soc_pcm_runtime *fe = asoc_substream_to_rtd(substream);
 	int ret, stream = substream->stream;
 
-	mutex_lock_nested(&fe->card->mutex, SND_SOC_CARD_CLASS_RUNTIME);
+	snd_soc_dpcm_mutex_lock(fe);
 	dpcm_set_fe_update_state(fe, stream, SND_SOC_DPCM_UPDATE_FE);
 
 	memcpy(&fe->dpcm[stream].hw_params, params,
@@ -1977,7 +2093,7 @@
 			params_channels(params), params_format(params));
 
 	/* call hw_params on the frontend */
-	ret = soc_pcm_hw_params(substream, params);
+	ret = __soc_pcm_hw_params(fe, substream, params);
 	if (ret < 0)
 		dpcm_be_dai_hw_free(fe, stream);
 	else
@@ -1985,7 +2101,7 @@
 
 out:
 	dpcm_set_fe_update_state(fe, stream, SND_SOC_DPCM_UPDATE_NO);
-	mutex_unlock(&fe->card->mutex);
+	snd_soc_dpcm_mutex_unlock(fe);
 
 	if (ret < 0)
 		dev_err(fe->dev, "ASoC: %s failed (%d)\n", __func__, ret);
@@ -1998,6 +2114,7 @@
 {
 	struct snd_soc_pcm_runtime *be;
 	struct snd_soc_dpcm *dpcm;
+	unsigned long flags;
 	int ret = 0;
 
 	for_each_dpcm_be(fe, stream, dpcm) {
@@ -2006,89 +2123,128 @@
 		be = dpcm->be;
 		be_substream = snd_soc_dpcm_get_substream(be, stream);
 
+		snd_soc_dpcm_stream_lock_irqsave_nested(be, stream, flags);
+
 		/* is this op for this BE ? */
 		if (!snd_soc_dpcm_be_can_update(fe, be, stream))
-			continue;
+			goto next;
 
 		dev_dbg(be->dev, "ASoC: trigger BE %s cmd %d\n",
 			be->dai_link->name, cmd);
 
 		switch (cmd) {
 		case SNDRV_PCM_TRIGGER_START:
-			if ((be->dpcm[stream].state != SND_SOC_DPCM_STATE_PREPARE) &&
+			if (!be->dpcm[stream].be_start &&
+			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_PREPARE) &&
 			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_STOP) &&
 			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_PAUSED))
-				continue;
+				goto next;
+
+			be->dpcm[stream].be_start++;
+			if (be->dpcm[stream].be_start != 1)
+				goto next;
 
 			ret = soc_pcm_trigger(be_substream, cmd);
-			if (ret)
-				goto end;
+			if (ret) {
+				be->dpcm[stream].be_start--;
+				goto next;
+			}
 
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_START;
 			break;
 		case SNDRV_PCM_TRIGGER_RESUME:
 			if ((be->dpcm[stream].state != SND_SOC_DPCM_STATE_SUSPEND))
-				continue;
+				goto next;
+
+			be->dpcm[stream].be_start++;
+			if (be->dpcm[stream].be_start != 1)
+				goto next;
 
 			ret = soc_pcm_trigger(be_substream, cmd);
-			if (ret)
-				goto end;
+			if (ret) {
+				be->dpcm[stream].be_start--;
+				goto next;
+			}
 
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_START;
 			break;
 		case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
-			if ((be->dpcm[stream].state != SND_SOC_DPCM_STATE_PAUSED))
-				continue;
+			if (!be->dpcm[stream].be_start &&
+			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_START) &&
+			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_STOP) &&
+			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_PAUSED))
+				goto next;
+
+			be->dpcm[stream].be_start++;
+			if (be->dpcm[stream].be_start != 1)
+				goto next;
 
 			ret = soc_pcm_trigger(be_substream, cmd);
-			if (ret)
-				goto end;
+			if (ret) {
+				be->dpcm[stream].be_start--;
+				goto next;
+			}
 
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_START;
 			break;
 		case SNDRV_PCM_TRIGGER_STOP:
 			if ((be->dpcm[stream].state != SND_SOC_DPCM_STATE_START) &&
 			    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_PAUSED))
-				continue;
+				goto next;
 
-			if (!snd_soc_dpcm_can_be_free_stop(fe, be, stream))
-				continue;
+			if (be->dpcm[stream].state == SND_SOC_DPCM_STATE_START)
+				be->dpcm[stream].be_start--;
+
+			if (be->dpcm[stream].be_start != 0)
+				goto next;
 
 			ret = soc_pcm_trigger(be_substream, cmd);
-			if (ret)
-				goto end;
+			if (ret) {
+				if (be->dpcm[stream].state == SND_SOC_DPCM_STATE_START)
+					be->dpcm[stream].be_start++;
+				goto next;
+			}
 
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_STOP;
 			break;
 		case SNDRV_PCM_TRIGGER_SUSPEND:
 			if (be->dpcm[stream].state != SND_SOC_DPCM_STATE_START)
-				continue;
+				goto next;
 
-			if (!snd_soc_dpcm_can_be_free_stop(fe, be, stream))
-				continue;
+			be->dpcm[stream].be_start--;
+			if (be->dpcm[stream].be_start != 0)
+				goto next;
 
 			ret = soc_pcm_trigger(be_substream, cmd);
-			if (ret)
-				goto end;
+			if (ret) {
+				be->dpcm[stream].be_start++;
+				goto next;
+			}
 
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_SUSPEND;
 			break;
 		case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
 			if (be->dpcm[stream].state != SND_SOC_DPCM_STATE_START)
-				continue;
+				goto next;
 
-			if (!snd_soc_dpcm_can_be_free_stop(fe, be, stream))
-				continue;
+			be->dpcm[stream].be_start--;
+			if (be->dpcm[stream].be_start != 0)
+				goto next;
 
 			ret = soc_pcm_trigger(be_substream, cmd);
-			if (ret)
-				goto end;
+			if (ret) {
+				be->dpcm[stream].be_start++;
+				goto next;
+			}
 
 			be->dpcm[stream].state = SND_SOC_DPCM_STATE_PAUSED;
 			break;
 		}
+next:
+		snd_soc_dpcm_stream_unlock_irqrestore(be, stream, flags);
+		if (ret)
+			break;
 	}
-end:
 	if (ret < 0)
 		dev_err(fe->dev, "ASoC: %s() failed at %s (%d)\n",
 			__func__, be->dai_link->name, ret);
@@ -2247,6 +2403,9 @@
 		if (!snd_soc_dpcm_be_can_update(fe, be, stream))
 			continue;
 
+		if (!snd_soc_dpcm_can_be_prepared(fe, be, stream))
+			continue;
+
 		if ((be->dpcm[stream].state != SND_SOC_DPCM_STATE_HW_PARAMS) &&
 		    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_STOP) &&
 		    (be->dpcm[stream].state != SND_SOC_DPCM_STATE_SUSPEND) &&
@@ -2256,7 +2415,7 @@
 		dev_dbg(be->dev, "ASoC: prepare BE %s\n",
 			be->dai_link->name);
 
-		ret = soc_pcm_prepare(be_substream);
+		ret = __soc_pcm_prepare(be, be_substream);
 		if (ret < 0)
 			break;
 
@@ -2274,7 +2433,7 @@
 	struct snd_soc_pcm_runtime *fe = asoc_substream_to_rtd(substream);
 	int stream = substream->stream, ret = 0;
 
-	mutex_lock_nested(&fe->card->mutex, SND_SOC_CARD_CLASS_RUNTIME);
+	snd_soc_dpcm_mutex_lock(fe);
 
 	dev_dbg(fe->dev, "ASoC: prepare FE %s\n", fe->dai_link->name);
 
@@ -2293,7 +2452,7 @@
 		goto out;
 
 	/* call prepare on the frontend */
-	ret = soc_pcm_prepare(substream);
+	ret = __soc_pcm_prepare(fe, substream);
 	if (ret < 0)
 		goto out;
 
@@ -2301,7 +2460,7 @@
 
 out:
 	dpcm_set_fe_update_state(fe, stream, SND_SOC_DPCM_UPDATE_NO);
-	mutex_unlock(&fe->card->mutex);
+	snd_soc_dpcm_mutex_unlock(fe);
 
 	if (ret < 0)
 		dev_err(fe->dev, "ASoC: %s() failed (%d)\n", __func__, ret);
@@ -2352,7 +2511,6 @@
 	struct snd_soc_dpcm *dpcm;
 	enum snd_soc_dpcm_trigger trigger = fe->dai_link->trigger[stream];
 	int ret = 0;
-	unsigned long flags;
 
 	dev_dbg(fe->dev, "ASoC: runtime %s open on FE %s\n",
 			stream ? "capture" : "playback", fe->dai_link->name);
@@ -2421,7 +2579,6 @@
 	dpcm_be_dai_shutdown(fe, stream);
 disconnect:
 	/* disconnect any pending BEs */
-	spin_lock_irqsave(&fe->card->dpcm_lock, flags);
 	for_each_dpcm_be(fe, stream, dpcm) {
 		struct snd_soc_pcm_runtime *be = dpcm->be;
 
@@ -2433,7 +2590,6 @@
 			be->dpcm[stream].state == SND_SOC_DPCM_STATE_NEW)
 				dpcm->state = SND_SOC_DPCM_LINK_STATE_FREE;
 	}
-	spin_unlock_irqrestore(&fe->card->dpcm_lock, flags);
 
 	if (ret < 0)
 		dev_err(fe->dev, "ASoC: %s() failed (%d)\n", __func__, ret);
@@ -2508,7 +2664,7 @@
 	struct snd_soc_pcm_runtime *fe;
 	int ret = 0;
 
-	mutex_lock_nested(&card->mutex, SND_SOC_CARD_CLASS_RUNTIME);
+	mutex_lock_nested(&card->pcm_mutex, card->pcm_subclass);
 	/* shutdown all old paths first */
 	for_each_card_rtds(card, fe) {
 		ret = soc_dpcm_fe_runtime_update(fe, 0);
@@ -2524,7 +2680,7 @@
 	}
 
 out:
-	mutex_unlock(&card->mutex);
+	mutex_unlock(&card->pcm_mutex);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(snd_soc_dpcm_runtime_update);
@@ -2535,6 +2691,8 @@
 	struct snd_soc_dpcm *dpcm;
 	int stream = fe_substream->stream;
 
+	snd_soc_dpcm_mutex_assert_held(fe);
+
 	/* mark FE's links ready to prune */
 	for_each_dpcm_be(fe, stream, dpcm)
 		dpcm->state = SND_SOC_DPCM_LINK_STATE_FREE;
@@ -2549,12 +2707,12 @@
 	struct snd_soc_pcm_runtime *fe = asoc_substream_to_rtd(fe_substream);
 	int ret;
 
-	mutex_lock_nested(&fe->card->mutex, SND_SOC_CARD_CLASS_RUNTIME);
+	snd_soc_dpcm_mutex_lock(fe);
 	ret = dpcm_fe_dai_shutdown(fe_substream);
 
 	dpcm_fe_dai_cleanup(fe_substream);
 
-	mutex_unlock(&fe->card->mutex);
+	snd_soc_dpcm_mutex_unlock(fe);
 	return ret;
 }
 
@@ -2565,7 +2723,7 @@
 	int ret;
 	int stream = fe_substream->stream;
 
-	mutex_lock_nested(&fe->card->mutex, SND_SOC_CARD_CLASS_RUNTIME);
+	snd_soc_dpcm_mutex_lock(fe);
 	fe->dpcm[stream].runtime = fe_substream->runtime;
 
 	ret = dpcm_path_get(fe, stream, &list);
@@ -2582,7 +2740,7 @@
 	dpcm_clear_pending_state(fe, stream);
 	dpcm_path_put(&list);
 open_end:
-	mutex_unlock(&fe->card->mutex);
+	snd_soc_dpcm_mutex_unlock(fe);
 	return ret;
 }
 
@@ -2843,10 +3001,8 @@
 	struct snd_soc_dpcm *dpcm;
 	int state;
 	int ret = 1;
-	unsigned long flags;
 	int i;
 
-	spin_lock_irqsave(&fe->card->dpcm_lock, flags);
 	for_each_dpcm_fe(be, stream, dpcm) {
 
 		if (dpcm->fe == fe)
@@ -2860,7 +3016,6 @@
 			}
 		}
 	}
-	spin_unlock_irqrestore(&fe->card->dpcm_lock, flags);
 
 	/* it's safe to do this BE DAI */
 	return ret;
@@ -2900,3 +3055,20 @@
 	return snd_soc_dpcm_check_state(fe, be, stream, state, ARRAY_SIZE(state));
 }
 EXPORT_SYMBOL_GPL(snd_soc_dpcm_can_be_params);
+
+/*
+ * We can only prepare a BE DAI if any of it's FE are not prepared,
+ * running or paused for the specified stream direction.
+ */
+int snd_soc_dpcm_can_be_prepared(struct snd_soc_pcm_runtime *fe,
+				 struct snd_soc_pcm_runtime *be, int stream)
+{
+	const enum snd_soc_dpcm_state state[] = {
+		SND_SOC_DPCM_STATE_START,
+		SND_SOC_DPCM_STATE_PAUSED,
+		SND_SOC_DPCM_STATE_PREPARE,
+	};
+
+	return snd_soc_dpcm_check_state(fe, be, stream, state, ARRAY_SIZE(state));
+}
+EXPORT_SYMBOL_GPL(snd_soc_dpcm_can_be_prepared);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-topology.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-topology.c
@@ -510,7 +510,8 @@
 
 	if (le32_to_cpu(hdr->ops.info) == SND_SOC_TPLG_CTL_BYTES
 		&& k->iface & SNDRV_CTL_ELEM_IFACE_MIXER
-		&& k->access & SNDRV_CTL_ELEM_ACCESS_TLV_READWRITE
+		&& (k->access & SNDRV_CTL_ELEM_ACCESS_TLV_READ
+		    || k->access & SNDRV_CTL_ELEM_ACCESS_TLV_WRITE)
 		&& k->access & SNDRV_CTL_ELEM_ACCESS_TLV_CALLBACK) {
 		struct soc_bytes_ext *sbe;
 		struct snd_soc_tplg_bytes_control *be;
@@ -912,6 +913,8 @@
 		se->dobj.control.dvalues[i] = le32_to_cpu(ec->values[i]);
 	}
 
+	se->items = le32_to_cpu(ec->items);
+	se->values = (const unsigned int *)se->dobj.control.dvalues;
 	return 0;
 }
 
@@ -1479,13 +1482,17 @@
 
 	template.num_kcontrols = le32_to_cpu(w->num_kcontrols);
 	kc = devm_kcalloc(tplg->dev, le32_to_cpu(w->num_kcontrols), sizeof(*kc), GFP_KERNEL);
-	if (!kc)
-		goto err;
+	if (!kc) {
+		ret = -ENOMEM;
+		goto hdr_err;
+	}
 
 	kcontrol_type = devm_kcalloc(tplg->dev, le32_to_cpu(w->num_kcontrols), sizeof(unsigned int),
 				     GFP_KERNEL);
-	if (!kcontrol_type)
-		goto err;
+	if (!kcontrol_type) {
+		ret = -ENOMEM;
+		goto hdr_err;
+	}
 
 	for (i = 0; i < w->num_kcontrols; i++) {
 		control_hdr = (struct snd_soc_tplg_ctl_hdr *)tplg->pos;
@@ -2674,6 +2681,7 @@
 /* remove dynamic controls from the component driver */
 int snd_soc_tplg_component_remove(struct snd_soc_component *comp)
 {
+	struct snd_card *card = comp->card->snd_card;
 	struct snd_soc_dobj *dobj, *next_dobj;
 	int pass = SOC_TPLG_PASS_END;
 
@@ -2681,6 +2689,7 @@
 	while (pass >= SOC_TPLG_PASS_START) {
 
 		/* remove mixer controls */
+		down_write(&card->controls_rwsem);
 		list_for_each_entry_safe(dobj, next_dobj, &comp->dobj_list,
 			list) {
 
@@ -2719,6 +2728,7 @@
 				break;
 			}
 		}
+		up_write(&card->controls_rwsem);
 		pass--;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/soc-utils.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/soc-utils.c
@@ -159,6 +159,7 @@
 		return 1;
 	return 0;
 }
+EXPORT_SYMBOL_GPL(snd_soc_dai_is_dummy);
 
 int snd_soc_component_is_dummy(struct snd_soc_component *component)
 {
@@ -206,7 +207,7 @@
 	return ret;
 }
 
-void __exit snd_soc_util_exit(void)
+void snd_soc_util_exit(void)
 {
 	platform_driver_unregister(&soc_dummy_driver);
 	platform_device_unregister(soc_dummy_dev);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/debug.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/debug.c
@@ -668,9 +668,9 @@
 	}
 
 	for (i = 0, len = 0; i < reply->num_elems; i++) {
-		ret = snprintf(buf + len, buff_size - len, "zone %d.%d used %#8x free %#8x\n",
-			       reply->elems[i].zone, reply->elems[i].id,
-			       reply->elems[i].used, reply->elems[i].free);
+		ret = scnprintf(buf + len, buff_size - len, "zone %d.%d used %#8x free %#8x\n",
+				reply->elems[i].zone, reply->elems[i].id,
+				reply->elems[i].used, reply->elems[i].free);
 		if (ret < 0)
 			goto error;
 		len += ret;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/imx/imx8m.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/imx/imx8m.c
@@ -191,6 +191,7 @@
 	}
 
 	ret = of_address_to_resource(res_node, 0, &res);
+	of_node_put(res_node);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to get reserved region address\n");
 		goto exit_pdev_unregister;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/Kconfig
@@ -84,6 +84,7 @@
 config SND_SOC_SOF_MERRIFIELD
 	tristate "SOF support for Tangier/Merrifield"
 	default SND_SOC_SOF_PCI
+	select SND_SOC_SOF_PCI_DEV
 	select SND_SOC_SOF_INTEL_ATOM_HIFI_EP
 	help
 	  This adds support for Sound Open Firmware for Intel(R) platforms
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/apl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/apl.c
@@ -139,6 +139,7 @@
 	.ipc_ack = HDA_DSP_REG_HIPCIE,
 	.ipc_ack_mask = HDA_DSP_REG_HIPCIE_DONE,
 	.ipc_ctl = HDA_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 150,
 	.ssp_count = APL_SSP_COUNT,
 	.ssp_base_offset = APL_SSP_BASE_OFFSET,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/cnl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/cnl.c
@@ -344,6 +344,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = CNL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
@@ -363,6 +364,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = ICL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda-bus.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda-bus.c
@@ -10,6 +10,8 @@
 #include <linux/io.h>
 #include <sound/hdaudio.h>
 #include <sound/hda_i915.h>
+#include <sound/hda_codec.h>
+#include <sound/hda_register.h>
 #include "../sof-priv.h"
 #include "hda.h"
 
@@ -21,6 +23,18 @@
 #endif
 
 #if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
+static void update_codec_wake_enable(struct hdac_bus *bus, unsigned int addr, bool link_power)
+{
+	unsigned int mask = snd_hdac_chip_readw(bus, WAKEEN);
+
+	if (link_power)
+		mask &= ~BIT(addr);
+	else
+		mask |= BIT(addr);
+
+	snd_hdac_chip_updatew(bus, WAKEEN, STATESTS_INT_MASK, mask);
+}
+
 static void sof_hda_bus_link_power(struct hdac_device *codec, bool enable)
 {
 	struct hdac_bus *bus = codec->bus;
@@ -41,6 +55,9 @@
 	 */
 	if (codec->addr == HDA_IDISP_ADDR && !enable)
 		snd_hdac_display_power(bus, HDA_CODEC_IDX_CONTROLLER, false);
+
+	/* WAKEEN needs to be set for disabled links */
+	update_codec_wake_enable(bus, codec->addr, enable);
 }
 
 static const struct hdac_bus_ops bus_core_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda-codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda-codec.c
@@ -258,6 +258,7 @@
 }
 EXPORT_SYMBOL_NS(hda_codec_i915_exit, SND_SOC_SOF_HDA_AUDIO_CODEC_I915);
 
+MODULE_SOFTDEP("pre: snd-hda-codec-hdmi");
 #endif
 
 MODULE_LICENSE("Dual BSD/GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda-dai.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda-dai.c
@@ -68,6 +68,7 @@
 		return NULL;
 	}
 
+	spin_lock_irq(&bus->reg_lock);
 	list_for_each_entry(stream, &bus->stream_list, list) {
 		struct hdac_ext_stream *hstream =
 			stream_to_hdac_ext_stream(stream);
@@ -107,12 +108,12 @@
 		 * is updated in snd_hdac_ext_stream_decouple().
 		 */
 		if (!res->decoupled)
-			snd_hdac_ext_stream_decouple(bus, res, true);
-		spin_lock_irq(&bus->reg_lock);
+			snd_hdac_ext_stream_decouple_locked(bus, res, true);
+
 		res->link_locked = 1;
 		res->link_substream = substream;
-		spin_unlock_irq(&bus->reg_lock);
 	}
+	spin_unlock_irq(&bus->reg_lock);
 
 	return res;
 }
@@ -211,6 +212,10 @@
 	int stream_tag;
 	int ret;
 
+	link = snd_hdac_ext_bus_get_link(bus, codec_dai->component->name);
+	if (!link)
+		return -EINVAL;
+
 	/* get stored dma data if resuming from system suspend */
 	link_dev = snd_soc_dai_get_dma_data(dai, substream);
 	if (!link_dev) {
@@ -231,15 +236,8 @@
 	if (ret < 0)
 		return ret;
 
-	link = snd_hdac_ext_bus_get_link(bus, codec_dai->component->name);
-	if (!link)
-		return -EINVAL;
-
-	/* set the stream tag in the codec dai dma params */
-	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-		snd_soc_dai_set_tdm_slot(codec_dai, stream_tag, 0, 0, 0);
-	else
-		snd_soc_dai_set_tdm_slot(codec_dai, 0, stream_tag, 0, 0);
+	/* set the hdac_stream in the codec dai */
+	snd_soc_dai_set_stream(codec_dai, hdac_stream(link_dev), substream->stream);
 
 	p_params.s_fmt = snd_pcm_format_width(params_format(params));
 	p_params.ch = params_channels(params);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda-dsp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda-dsp.c
@@ -623,8 +623,7 @@
 	hda_dsp_ipc_int_disable(sdev);
 
 #if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
-	if (runtime_suspend)
-		hda_codec_jack_wake_enable(sdev, true);
+	hda_codec_jack_wake_enable(sdev, runtime_suspend);
 
 	/* power down all hda link */
 	snd_hdac_ext_bus_link_power_down_all(bus);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda-loader.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda-loader.c
@@ -48,7 +48,7 @@
 	ret = snd_dma_alloc_pages(SNDRV_DMA_TYPE_DEV_SG, &pci->dev, size, dmab);
 	if (ret < 0) {
 		dev_err(sdev->dev, "error: memory alloc failed: %d\n", ret);
-		goto error;
+		goto out_put;
 	}
 
 	hstream->period_bytes = 0;/* initialize period_bytes */
@@ -59,29 +59,30 @@
 		ret = hda_dsp_iccmax_stream_hw_params(sdev, dsp_stream, dmab, NULL);
 		if (ret < 0) {
 			dev_err(sdev->dev, "error: iccmax stream prepare failed: %d\n", ret);
-			goto error;
+			goto out_free;
 		}
 	} else {
 		ret = hda_dsp_stream_hw_params(sdev, dsp_stream, dmab, NULL);
 		if (ret < 0) {
 			dev_err(sdev->dev, "error: hdac prepare failed: %d\n", ret);
-			goto error;
+			goto out_free;
 		}
 		hda_dsp_stream_spib_config(sdev, dsp_stream, HDA_DSP_SPIB_ENABLE, size);
 	}
 
 	return dsp_stream;
 
-error:
-	hda_dsp_stream_put(sdev, direction, hstream->stream_tag);
+out_free:
 	snd_dma_free_pages(dmab);
+out_put:
+	hda_dsp_stream_put(sdev, direction, hstream->stream_tag);
 	return ERR_PTR(ret);
 }
 
 /*
- * first boot sequence has some extra steps. core 0 waits for power
- * status on core 1, so power up core 1 also momentarily, keep it in
- * reset/stall and then turn it off
+ * first boot sequence has some extra steps.
+ * power on all host managed cores and only unstall/run the boot core to boot the
+ * DSP then turn off all non boot cores (if any) is powered on.
  */
 static int cl_dsp_init(struct snd_sof_dev *sdev, int stream_tag)
 {
@@ -116,7 +117,7 @@
 			  ((stream_tag - 1) << 9)));
 
 	/* step 3: unset core 0 reset state & unstall/run core 0 */
-	ret = hda_dsp_core_run(sdev, BIT(0));
+	ret = hda_dsp_core_run(sdev, chip->init_core_mask);
 	if (ret < 0) {
 		if (hda->boot_iteration == HDA_FW_BOOT_ATTEMPTS)
 			dev_err(sdev->dev,
@@ -162,7 +163,7 @@
 
 	/* step 7: wait for ROM init */
 	ret = snd_sof_dsp_read_poll_timeout(sdev, HDA_DSP_BAR,
-					HDA_DSP_SRAM_REG_ROM_STATUS, status,
+					chip->rom_status_reg, status,
 					((status & HDA_DSP_ROM_STS_MASK)
 						== HDA_DSP_ROM_INIT),
 					HDA_DSP_REG_POLL_INTERVAL_US,
@@ -173,8 +174,8 @@
 
 	if (hda->boot_iteration == HDA_FW_BOOT_ATTEMPTS)
 		dev_err(sdev->dev,
-			"error: %s: timeout HDA_DSP_SRAM_REG_ROM_STATUS read\n",
-			__func__);
+			"%s: timeout with rom_status_reg (%#x) read\n",
+			__func__, chip->rom_status_reg);
 
 err:
 	flags = SOF_DBG_DUMP_REGS | SOF_DBG_DUMP_PCI | SOF_DBG_DUMP_MBOX;
@@ -250,6 +251,8 @@
 
 static int cl_copy_fw(struct snd_sof_dev *sdev, struct hdac_ext_stream *stream)
 {
+	struct sof_intel_hda_dev *hda = sdev->pdata->hw_pdata;
+	const struct sof_intel_dsp_desc *chip = hda->desc;
 	unsigned int reg;
 	int ret, status;
 
@@ -260,7 +263,7 @@
 	}
 
 	status = snd_sof_dsp_read_poll_timeout(sdev, HDA_DSP_BAR,
-					HDA_DSP_SRAM_REG_ROM_STATUS, reg,
+					chip->rom_status_reg, reg,
 					((reg & HDA_DSP_ROM_STS_MASK)
 						== HDA_DSP_ROM_FW_ENTERED),
 					HDA_DSP_REG_POLL_INTERVAL_US,
@@ -273,8 +276,8 @@
 
 	if (status < 0) {
 		dev_err(sdev->dev,
-			"error: %s: timeout HDA_DSP_SRAM_REG_ROM_STATUS read\n",
-			__func__);
+			"%s: timeout with rom_status_reg (%#x) read\n",
+			__func__, chip->rom_status_reg);
 	}
 
 	ret = cl_trigger(sdev, stream, SNDRV_PCM_TRIGGER_STOP);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda-pcm.c
@@ -242,6 +242,7 @@
 		runtime->hw.info &= ~SNDRV_PCM_INFO_PAUSE;
 
 	if (hda_always_enable_dmi_l1 ||
+	    direction == SNDRV_PCM_STREAM_PLAYBACK ||
 	    spcm->stream[substream->stream].d0i3_compatible)
 		flags |= SOF_HDA_STREAM_DMI_L1_COMPATIBLE;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/hda.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/hda.c
@@ -353,11 +353,13 @@
 
 static void hda_dsp_get_status(struct snd_sof_dev *sdev)
 {
+	const struct sof_intel_dsp_desc *chip;
 	u32 status;
 	int i;
 
+	chip = get_chip_info(sdev->pdata);
 	status = snd_sof_dsp_read(sdev, HDA_DSP_BAR,
-				  HDA_DSP_SRAM_REG_ROM_STATUS);
+				  chip->rom_status_reg);
 
 	for (i = 0; i < ARRAY_SIZE(hda_dsp_rom_msg); i++) {
 		if (status == hda_dsp_rom_msg[i].code) {
@@ -402,14 +404,16 @@
 /* dump the first 8 dwords representing the extended ROM status */
 static void hda_dsp_dump_ext_rom_status(struct snd_sof_dev *sdev, u32 flags)
 {
+	const struct sof_intel_dsp_desc *chip;
 	char msg[128];
 	int len = 0;
 	u32 value;
 	int i;
 
+	chip = get_chip_info(sdev->pdata);
 	for (i = 0; i < HDA_EXT_ROM_STATUS_SIZE; i++) {
-		value = snd_sof_dsp_read(sdev, HDA_DSP_BAR, HDA_DSP_SRAM_REG_ROM_STATUS + i * 0x4);
-		len += snprintf(msg + len, sizeof(msg) - len, " 0x%x", value);
+		value = snd_sof_dsp_read(sdev, HDA_DSP_BAR, chip->rom_status_reg + i * 0x4);
+		len += scnprintf(msg + len, sizeof(msg) - len, " 0x%x", value);
 	}
 
 	sof_dev_dbg_or_err(sdev->dev, flags & SOF_DBG_DUMP_FORCE_ERR_LEVEL,
@@ -696,6 +700,20 @@
 	return 0;
 }
 
+static void hda_check_for_state_change(struct snd_sof_dev *sdev)
+{
+#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
+	struct hdac_bus *bus = sof_to_bus(sdev);
+	unsigned int codec_mask;
+
+	codec_mask = snd_hdac_chip_readw(bus, STATESTS);
+	if (codec_mask) {
+		hda_codec_jack_check(sdev);
+		snd_hdac_chip_writew(bus, STATESTS, codec_mask);
+	}
+#endif
+}
+
 static irqreturn_t hda_dsp_interrupt_handler(int irq, void *context)
 {
 	struct snd_sof_dev *sdev = context;
@@ -737,6 +755,8 @@
 	if (hda_sdw_check_wakeen_irq(sdev))
 		hda_sdw_process_wakeen(sdev);
 
+	hda_check_for_state_change(sdev);
+
 	/* enable GIE interrupt */
 	snd_sof_dsp_update_bits(sdev, HDA_DSP_HDA_BAR,
 				SOF_HDA_INTCTL,
@@ -1020,12 +1040,22 @@
 			pdata->machine = hda_mach;
 			pdata->tplg_filename = tplg_filename;
 
-			if (codec_num == 2) {
+			if (codec_num == 2 ||
+			    (codec_num == 1 && !HDA_IDISP_CODEC(bus->codec_mask))) {
 				/*
 				 * Prevent SoundWire links from starting when an external
 				 * HDaudio codec is used
 				 */
 				hda_mach->mach_params.link_mask = 0;
+			} else {
+				/*
+				 * Allow SoundWire links to start when no external HDaudio codec
+				 * was detected. This will not create a SoundWire card but
+				 * will help detect if any SoundWire codec reports as ATTACHED.
+				 */
+				struct sof_intel_hda_dev *hdev = sdev->pdata->hw_pdata;
+
+				hda_mach->mach_params.link_mask = hdev->info.link_mask;
 			}
 		}
 	}
@@ -1056,7 +1086,7 @@
 	struct hdac_bus *bus = sof_to_bus(sdev);
 	struct sdw_intel_slave_id *ids = sdw->ids;
 	int num_slaves = sdw->num_slaves;
-	unsigned int part_id, link_id, unique_id, mfg_id;
+	unsigned int part_id, link_id, unique_id, mfg_id, version;
 	int i, j, k;
 
 	for (i = 0; i < link->num_adr; i++) {
@@ -1066,12 +1096,14 @@
 		mfg_id = SDW_MFG_ID(adr);
 		part_id = SDW_PART_ID(adr);
 		link_id = SDW_DISCO_LINK_ID(adr);
+		version = SDW_VERSION(adr);
 
 		for (j = 0; j < num_slaves; j++) {
 			/* find out how many identical parts were reported on that link */
 			if (ids[j].link_id == link_id &&
 			    ids[j].id.part_id == part_id &&
-			    ids[j].id.mfg_id == mfg_id)
+			    ids[j].id.mfg_id == mfg_id &&
+			    ids[j].id.sdw_version == version)
 				reported_part_count++;
 		}
 
@@ -1080,21 +1112,24 @@
 
 			if (ids[j].link_id != link_id ||
 			    ids[j].id.part_id != part_id ||
-			    ids[j].id.mfg_id != mfg_id)
+			    ids[j].id.mfg_id != mfg_id ||
+			    ids[j].id.sdw_version != version)
 				continue;
 
 			/* find out how many identical parts are expected */
 			for (k = 0; k < link->num_adr; k++) {
 				u64 adr2 = link->adr_d[k].adr;
-				unsigned int part_id2, link_id2, mfg_id2;
+				unsigned int part_id2, link_id2, mfg_id2, version2;
 
 				mfg_id2 = SDW_MFG_ID(adr2);
 				part_id2 = SDW_PART_ID(adr2);
 				link_id2 = SDW_DISCO_LINK_ID(adr2);
+				version2 = SDW_VERSION(adr2);
 
 				if (link_id2 == link_id &&
 				    part_id2 == part_id &&
-				    mfg_id2 == mfg_id)
+				    mfg_id2 == mfg_id &&
+				    version2 == version)
 					expected_part_count++;
 			}
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/icl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/icl.c
@@ -139,6 +139,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = ICL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/pci-tgl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/pci-tgl.c
@@ -117,8 +117,12 @@
 		.driver_data = (unsigned long)&adls_desc},
 	{ PCI_DEVICE(0x8086, 0x51c8), /* ADL-P */
 		.driver_data = (unsigned long)&adl_desc},
+	{ PCI_DEVICE(0x8086, 0x51cd), /* ADL-P */
+		.driver_data = (unsigned long)&adl_desc},
 	{ PCI_DEVICE(0x8086, 0x51cc), /* ADL-M */
 		.driver_data = (unsigned long)&adl_desc},
+	{ PCI_DEVICE(0x8086, 0x54c8), /* ADL-N */
+		.driver_data = (unsigned long)&adl_desc},
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, sof_pci_ids);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/shim.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/shim.h
@@ -161,6 +161,7 @@
 	int ipc_ack;
 	int ipc_ack_mask;
 	int ipc_ctl;
+	int rom_status_reg;
 	int rom_init_timeout;
 	int ssp_count;			/* ssp count of the platform */
 	int ssp_base_offset;		/* base address of the SSPs */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/intel/tgl.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/intel/tgl.c
@@ -134,6 +134,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = ICL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
@@ -153,6 +154,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = ICL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
@@ -172,6 +174,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = ICL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
@@ -191,6 +194,7 @@
 	.ipc_ack = CNL_DSP_REG_HIPCIDA,
 	.ipc_ack_mask = CNL_DSP_REG_HIPCIDA_DONE,
 	.ipc_ctl = CNL_DSP_REG_HIPCCTL,
+	.rom_status_reg = HDA_DSP_SRAM_REG_ROM_STATUS,
 	.rom_init_timeout	= 300,
 	.ssp_count = ICL_SSP_COUNT,
 	.ssp_base_offset = CNL_SSP_BASE_OFFSET,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/sof-pci-dev.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/sof-pci-dev.c
@@ -12,6 +12,7 @@
 #include <linux/dmi.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/platform_data/x86/soc.h>
 #include <linux/pm_runtime.h>
 #include <sound/soc-acpi.h>
 #include <sound/soc-acpi-intel-match.h>
@@ -27,17 +28,22 @@
 module_param(tplg_path, charp, 0444);
 MODULE_PARM_DESC(tplg_path, "alternate path for SOF topology.");
 
+static char *tplg_filename;
+module_param(tplg_filename, charp, 0444);
+MODULE_PARM_DESC(tplg_filename, "alternate filename for SOF topology.");
+
 static int sof_pci_debug;
 module_param_named(sof_pci_debug, sof_pci_debug, int, 0444);
 MODULE_PARM_DESC(sof_pci_debug, "SOF PCI debug options (0x0 all off)");
 
-static const char *sof_override_tplg_name;
+static const char *sof_dmi_override_tplg_name;
+static bool sof_dmi_use_community_key;
 
 #define SOF_PCI_DISABLE_PM_RUNTIME BIT(0)
 
 static int sof_tplg_cb(const struct dmi_system_id *id)
 {
-	sof_override_tplg_name = id->driver_data;
+	sof_dmi_override_tplg_name = id->driver_data;
 	return 1;
 }
 
@@ -62,25 +68,44 @@
 	{}
 };
 
+/* all Up boards use the community key */
+static int up_use_community_key(const struct dmi_system_id *id)
+{
+	sof_dmi_use_community_key = true;
+	return 1;
+}
+
+/*
+ * For ApolloLake Chromebooks we want to force the use of the Intel production key.
+ * All newer platforms use the community key
+ */
+static int chromebook_use_community_key(const struct dmi_system_id *id)
+{
+	if (!soc_intel_is_apl())
+		sof_dmi_use_community_key = true;
+	return 1;
+}
+
 static const struct dmi_system_id community_key_platforms[] = {
 	{
-		.ident = "Up Squared",
+		.ident = "Up boards",
+		.callback = up_use_community_key,
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "AAEON"),
-			DMI_MATCH(DMI_BOARD_NAME, "UP-APL01"),
 		}
 	},
 	{
-		.ident = "Up Extreme",
+		.ident = "Google Chromebooks",
+		.callback = chromebook_use_community_key,
 		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "AAEON"),
-			DMI_MATCH(DMI_BOARD_NAME, "UP-WHL01"),
+			DMI_MATCH(DMI_PRODUCT_FAMILY, "Google"),
 		}
 	},
 	{
-		.ident = "Google Chromebooks",
+		.ident = "Google firmware",
+		.callback = chromebook_use_community_key,
 		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "Google"),
+			DMI_MATCH(DMI_BIOS_VERSION, "Google"),
 		}
 	},
 	{},
@@ -129,6 +154,11 @@
 
 	dev_dbg(&pci->dev, "PCI DSP detected");
 
+	if (!desc) {
+		dev_err(dev, "error: no matching PCI descriptor\n");
+		return -ENODEV;
+	}
+
 	if (!desc->ops) {
 		dev_err(dev, "error: no matching PCI descriptor ops\n");
 		return -ENODEV;
@@ -166,7 +196,7 @@
 			"Module parameter used, changed fw path to %s\n",
 			sof_pdata->fw_filename_prefix);
 
-	} else if (dmi_check_system(community_key_platforms)) {
+	} else if (dmi_check_system(community_key_platforms) && sof_dmi_use_community_key) {
 		sof_pdata->fw_filename_prefix =
 			devm_kasprintf(dev, GFP_KERNEL, "%s/%s",
 				       sof_pdata->desc->default_fw_path,
@@ -186,9 +216,20 @@
 		sof_pdata->tplg_filename_prefix =
 			sof_pdata->desc->default_tplg_path;
 
-	dmi_check_system(sof_tplg_table);
-	if (sof_override_tplg_name)
-		sof_pdata->tplg_filename = sof_override_tplg_name;
+	/*
+	 * the topology filename will be provided in the machine descriptor, unless
+	 * it is overridden by a module parameter or DMI quirk.
+	 */
+	if (tplg_filename) {
+		sof_pdata->tplg_filename = tplg_filename;
+
+		dev_dbg(dev, "Module parameter used, changed tplg filename to %s\n",
+			sof_pdata->tplg_filename);
+	} else {
+		dmi_check_system(sof_tplg_table);
+		if (sof_dmi_override_tplg_name)
+			sof_pdata->tplg_filename = sof_dmi_override_tplg_name;
+	}
 
 	/* set callback to be called on successful device probe to enable runtime_pm */
 	sof_pdata->sof_probe_complete = sof_pci_probe_complete;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sof/topology.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sof/topology.c
@@ -2598,6 +2598,15 @@
 
 		/* power down the pipeline schedule core */
 		pipeline = swidget->private;
+
+		/*
+		 * Runtime PM should still function normally if topology loading fails and
+		 * it's components are unloaded. Do not power down the primary core so that the
+		 * CTX_SAVE IPC can succeed during runtime suspend.
+		 */
+		if (pipeline->core == SOF_DSP_PRIMARY_CORE)
+			break;
+
 		ret = snd_sof_dsp_core_power_down(sdev, 1 << pipeline->core);
 		if (ret < 0)
 			dev_err(scomp->dev, "error: powering down pipeline schedule core %d\n",
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sti/uniperif_player.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sti/uniperif_player.c
@@ -91,7 +91,7 @@
 			SET_UNIPERIF_ITM_BCLR_FIFO_ERROR(player);
 
 			/* Stop the player */
-			snd_pcm_stop_xrun(player->substream);
+			snd_pcm_stop(player->substream, SNDRV_PCM_STATE_XRUN);
 		}
 
 		ret = IRQ_HANDLED;
@@ -105,7 +105,7 @@
 		SET_UNIPERIF_ITM_BCLR_DMA_ERROR(player);
 
 		/* Stop the player */
-		snd_pcm_stop_xrun(player->substream);
+		snd_pcm_stop(player->substream, SNDRV_PCM_STATE_XRUN);
 
 		ret = IRQ_HANDLED;
 	}
@@ -138,7 +138,7 @@
 		dev_err(player->dev, "Underflow recovery failed\n");
 
 		/* Stop the player */
-		snd_pcm_stop_xrun(player->substream);
+		snd_pcm_stop(player->substream, SNDRV_PCM_STATE_XRUN);
 
 		ret = IRQ_HANDLED;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sti/uniperif_reader.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sti/uniperif_reader.c
@@ -65,7 +65,7 @@
 	if (unlikely(status & UNIPERIF_ITS_FIFO_ERROR_MASK(reader))) {
 		dev_err(reader->dev, "FIFO error detected\n");
 
-		snd_pcm_stop_xrun(reader->substream);
+		snd_pcm_stop(reader->substream, SNDRV_PCM_STATE_XRUN);
 
 		ret = IRQ_HANDLED;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/stm/stm32_adfsdm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/stm/stm32_adfsdm.c
@@ -303,6 +303,11 @@
 	return 0;
 }
 
+static void stm32_adfsdm_cleanup(void *data)
+{
+	iio_channel_release_all_cb(data);
+}
+
 static struct snd_soc_component_driver stm32_adfsdm_soc_platform = {
 	.open		= stm32_adfsdm_pcm_open,
 	.close		= stm32_adfsdm_pcm_close,
@@ -349,6 +354,12 @@
 	if (IS_ERR(priv->iio_cb))
 		return PTR_ERR(priv->iio_cb);
 
+	ret = devm_add_action_or_reset(&pdev->dev, stm32_adfsdm_cleanup, priv->iio_cb);
+	if (ret < 0)  {
+		dev_err(&pdev->dev, "Unable to add action\n");
+		return ret;
+	}
+
 	component = devm_kzalloc(&pdev->dev, sizeof(*component), GFP_KERNEL);
 	if (!component)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/stm/stm32_i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/stm/stm32_i2s.c
@@ -700,7 +700,7 @@
 		if (ret < 0)
 			return ret;
 
-		nb_bits = frame_len * ((cgfr & I2S_CGFR_CHLEN) + 1);
+		nb_bits = frame_len * (FIELD_GET(I2S_CGFR_CHLEN, cgfr) + 1);
 		ret = stm32_i2s_calc_clk_div(i2s, i2s_clock_rate,
 					     (nb_bits * rate));
 		if (ret)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/stm/stm32_sai_sub.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/stm/stm32_sai_sub.c
@@ -319,7 +319,7 @@
 	int div;
 
 	div = DIV_ROUND_CLOSEST(input_rate, output_rate);
-	if (div > SAI_XCR1_MCKDIV_MAX(version)) {
+	if (div > SAI_XCR1_MCKDIV_MAX(version) || div <= 0) {
 		dev_err(&sai->pdev->dev, "Divider %d out of range\n", div);
 		return -EINVAL;
 	}
@@ -380,8 +380,8 @@
 	int div;
 
 	div = stm32_sai_get_clk_div(sai, *prate, rate);
-	if (div < 0)
-		return div;
+	if (div <= 0)
+		return -EINVAL;
 
 	mclk->freq = *prate / div;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/stm/stm32_spdifrx.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/stm/stm32_spdifrx.c
@@ -947,7 +947,7 @@
 {
 	struct stm32_spdifrx_data *spdifrx = platform_get_drvdata(pdev);
 
-	if (spdifrx->ctrl_chan)
+	if (!IS_ERR(spdifrx->ctrl_chan))
 		dma_release_channel(spdifrx->ctrl_chan);
 
 	if (spdifrx->dmab)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sunxi/sun4i-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sunxi/sun4i-i2s.c
@@ -100,8 +100,8 @@
 #define SUN8I_I2S_CTRL_MODE_PCM			(0 << 4)
 
 #define SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK	BIT(19)
-#define SUN8I_I2S_FMT0_LRCLK_POLARITY_INVERTED		(1 << 19)
-#define SUN8I_I2S_FMT0_LRCLK_POLARITY_NORMAL		(0 << 19)
+#define SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH	(1 << 19)
+#define SUN8I_I2S_FMT0_LRCLK_POLARITY_START_LOW		(0 << 19)
 #define SUN8I_I2S_FMT0_LRCK_PERIOD_MASK		GENMASK(17, 8)
 #define SUN8I_I2S_FMT0_LRCK_PERIOD(period)	((period - 1) << 8)
 #define SUN8I_I2S_FMT0_BCLK_POLARITY_MASK	BIT(7)
@@ -709,65 +709,37 @@
 static int sun8i_i2s_set_soc_fmt(const struct sun4i_i2s *i2s,
 				 unsigned int fmt)
 {
-	u32 mode, val;
+	u32 mode, lrclk_pol, bclk_pol, val;
 	u8 offset;
 
-	/*
-	 * DAI clock polarity
-	 *
-	 * The setup for LRCK contradicts the datasheet, but under a
-	 * scope it's clear that the LRCK polarity is reversed
-	 * compared to the expected polarity on the bus.
-	 */
-	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
-	case SND_SOC_DAIFMT_IB_IF:
-		/* Invert both clocks */
-		val = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED;
-		break;
-	case SND_SOC_DAIFMT_IB_NF:
-		/* Invert bit clock */
-		val = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED |
-		      SUN8I_I2S_FMT0_LRCLK_POLARITY_INVERTED;
-		break;
-	case SND_SOC_DAIFMT_NB_IF:
-		/* Invert frame clock */
-		val = 0;
-		break;
-	case SND_SOC_DAIFMT_NB_NF:
-		val = SUN8I_I2S_FMT0_LRCLK_POLARITY_INVERTED;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	regmap_update_bits(i2s->regmap, SUN4I_I2S_FMT0_REG,
-			   SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK |
-			   SUN8I_I2S_FMT0_BCLK_POLARITY_MASK,
-			   val);
-
 	/* DAI Mode */
 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
 	case SND_SOC_DAIFMT_DSP_A:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_PCM;
 		offset = 1;
 		break;
 
 	case SND_SOC_DAIFMT_DSP_B:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_PCM;
 		offset = 0;
 		break;
 
 	case SND_SOC_DAIFMT_I2S:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_LOW;
 		mode = SUN8I_I2S_CTRL_MODE_LEFT;
 		offset = 1;
 		break;
 
 	case SND_SOC_DAIFMT_LEFT_J:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_LEFT;
 		offset = 0;
 		break;
 
 	case SND_SOC_DAIFMT_RIGHT_J:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_RIGHT;
 		offset = 0;
 		break;
@@ -785,6 +757,35 @@
 			   SUN8I_I2S_TX_CHAN_OFFSET_MASK,
 			   SUN8I_I2S_TX_CHAN_OFFSET(offset));
 
+	/* DAI clock polarity */
+	bclk_pol = SUN8I_I2S_FMT0_BCLK_POLARITY_NORMAL;
+
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_IB_IF:
+		/* Invert both clocks */
+		lrclk_pol ^= SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK;
+		bclk_pol = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED;
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		/* Invert bit clock */
+		bclk_pol = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED;
+		break;
+	case SND_SOC_DAIFMT_NB_IF:
+		/* Invert frame clock */
+		lrclk_pol ^= SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK;
+		break;
+	case SND_SOC_DAIFMT_NB_NF:
+		/* No inversion */
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap_update_bits(i2s->regmap, SUN4I_I2S_FMT0_REG,
+			   SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK |
+			   SUN8I_I2S_FMT0_BCLK_POLARITY_MASK,
+			   lrclk_pol | bclk_pol);
+
 	/* DAI clock master masks */
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
 	case SND_SOC_DAIFMT_CBS_CFS:
@@ -816,65 +817,37 @@
 static int sun50i_h6_i2s_set_soc_fmt(const struct sun4i_i2s *i2s,
 				     unsigned int fmt)
 {
-	u32 mode, val;
+	u32 mode, lrclk_pol, bclk_pol, val;
 	u8 offset;
 
-	/*
-	 * DAI clock polarity
-	 *
-	 * The setup for LRCK contradicts the datasheet, but under a
-	 * scope it's clear that the LRCK polarity is reversed
-	 * compared to the expected polarity on the bus.
-	 */
-	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
-	case SND_SOC_DAIFMT_IB_IF:
-		/* Invert both clocks */
-		val = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED;
-		break;
-	case SND_SOC_DAIFMT_IB_NF:
-		/* Invert bit clock */
-		val = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED |
-		      SUN8I_I2S_FMT0_LRCLK_POLARITY_INVERTED;
-		break;
-	case SND_SOC_DAIFMT_NB_IF:
-		/* Invert frame clock */
-		val = 0;
-		break;
-	case SND_SOC_DAIFMT_NB_NF:
-		val = SUN8I_I2S_FMT0_LRCLK_POLARITY_INVERTED;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	regmap_update_bits(i2s->regmap, SUN4I_I2S_FMT0_REG,
-			   SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK |
-			   SUN8I_I2S_FMT0_BCLK_POLARITY_MASK,
-			   val);
-
 	/* DAI Mode */
 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
 	case SND_SOC_DAIFMT_DSP_A:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_PCM;
 		offset = 1;
 		break;
 
 	case SND_SOC_DAIFMT_DSP_B:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_PCM;
 		offset = 0;
 		break;
 
 	case SND_SOC_DAIFMT_I2S:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_LOW;
 		mode = SUN8I_I2S_CTRL_MODE_LEFT;
 		offset = 1;
 		break;
 
 	case SND_SOC_DAIFMT_LEFT_J:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_LEFT;
 		offset = 0;
 		break;
 
 	case SND_SOC_DAIFMT_RIGHT_J:
+		lrclk_pol = SUN8I_I2S_FMT0_LRCLK_POLARITY_START_HIGH;
 		mode = SUN8I_I2S_CTRL_MODE_RIGHT;
 		offset = 0;
 		break;
@@ -892,6 +865,36 @@
 			   SUN50I_H6_I2S_TX_CHAN_SEL_OFFSET_MASK,
 			   SUN50I_H6_I2S_TX_CHAN_SEL_OFFSET(offset));
 
+	/* DAI clock polarity */
+	bclk_pol = SUN8I_I2S_FMT0_BCLK_POLARITY_NORMAL;
+
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_IB_IF:
+		/* Invert both clocks */
+		lrclk_pol ^= SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK;
+		bclk_pol = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED;
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		/* Invert bit clock */
+		bclk_pol = SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED;
+		break;
+	case SND_SOC_DAIFMT_NB_IF:
+		/* Invert frame clock */
+		lrclk_pol ^= SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK;
+		break;
+	case SND_SOC_DAIFMT_NB_NF:
+		/* No inversion */
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap_update_bits(i2s->regmap, SUN4I_I2S_FMT0_REG,
+			   SUN8I_I2S_FMT0_LRCLK_POLARITY_MASK |
+			   SUN8I_I2S_FMT0_BCLK_POLARITY_MASK,
+			   lrclk_pol | bclk_pol);
+
+
 	/* DAI clock master masks */
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
 	case SND_SOC_DAIFMT_CBS_CFS:
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/sunxi/sun4i-spdif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/sunxi/sun4i-spdif.c
@@ -175,6 +175,7 @@
 	unsigned int reg_dac_txdata;
 	bool has_reset;
 	unsigned int val_fctl_ftx;
+	unsigned int mclk_multiplier;
 };
 
 struct sun4i_spdif_dev {
@@ -311,6 +312,7 @@
 	default:
 		return -EINVAL;
 	}
+	mclk *= host->quirks->mclk_multiplier;
 
 	ret = clk_set_rate(host->spdif_clk, mclk);
 	if (ret < 0) {
@@ -345,6 +347,7 @@
 	default:
 		return -EINVAL;
 	}
+	mclk_div *= host->quirks->mclk_multiplier;
 
 	reg_val = 0;
 	reg_val |= SUN4I_SPDIF_TXCFG_ASS;
@@ -427,24 +430,28 @@
 static const struct sun4i_spdif_quirks sun4i_a10_spdif_quirks = {
 	.reg_dac_txdata	= SUN4I_SPDIF_TXFIFO,
 	.val_fctl_ftx   = SUN4I_SPDIF_FCTL_FTX,
+	.mclk_multiplier = 1,
 };
 
 static const struct sun4i_spdif_quirks sun6i_a31_spdif_quirks = {
 	.reg_dac_txdata	= SUN4I_SPDIF_TXFIFO,
 	.val_fctl_ftx   = SUN4I_SPDIF_FCTL_FTX,
 	.has_reset	= true,
+	.mclk_multiplier = 1,
 };
 
 static const struct sun4i_spdif_quirks sun8i_h3_spdif_quirks = {
 	.reg_dac_txdata	= SUN8I_SPDIF_TXFIFO,
 	.val_fctl_ftx   = SUN4I_SPDIF_FCTL_FTX,
 	.has_reset	= true,
+	.mclk_multiplier = 4,
 };
 
 static const struct sun4i_spdif_quirks sun50i_h6_spdif_quirks = {
 	.reg_dac_txdata = SUN8I_SPDIF_TXFIFO,
 	.val_fctl_ftx   = SUN50I_H6_SPDIF_FCTL_FTX,
 	.has_reset      = true,
+	.mclk_multiplier = 1,
 };
 
 static const struct of_device_id sun4i_spdif_of_match[] = {
@@ -464,6 +471,11 @@
 		.compatible = "allwinner,sun50i-h6-spdif",
 		.data = &sun50i_h6_spdif_quirks,
 	},
+	{
+		.compatible = "allwinner,sun50i-h616-spdif",
+		/* Essentially the same as the H6, but without RX */
+		.data = &sun50i_h6_spdif_quirks,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, sun4i_spdif_of_match);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra186_dspk.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra186_dspk.c
@@ -1,8 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
+// SPDX-FileCopyrightText: Copyright (c) 2020-2024 NVIDIA CORPORATION & AFFILIATES. All rights reserved.
 //
 // tegra186_dspk.c - Tegra186 DSPK driver
-//
-// Copyright (c) 2020 NVIDIA CORPORATION. All rights reserved.
 
 #include <linux/clk.h>
 #include <linux/device.h>
@@ -26,51 +25,162 @@
 	{ TEGRA186_DSPK_CODEC_CTRL,  0x03000000 },
 };
 
-static int tegra186_dspk_get_control(struct snd_kcontrol *kcontrol,
+static int tegra186_dspk_get_fifo_th(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+
+	ucontrol->value.integer.value[0] = dspk->rx_fifo_th;
+
+	return 0;
+}
+
+static int tegra186_dspk_put_fifo_th(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+	int value = ucontrol->value.integer.value[0];
+
+	if (value == dspk->rx_fifo_th)
+		return 0;
+
+	dspk->rx_fifo_th = value;
+
+	return 1;
+}
+
+static int tegra186_dspk_get_osr_val(struct snd_kcontrol *kcontrol,
 				     struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
 	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
 
-	if (strstr(kcontrol->id.name, "FIFO Threshold"))
-		ucontrol->value.integer.value[0] = dspk->rx_fifo_th;
-	else if (strstr(kcontrol->id.name, "OSR Value"))
-		ucontrol->value.integer.value[0] = dspk->osr_val;
-	else if (strstr(kcontrol->id.name, "LR Polarity Select"))
-		ucontrol->value.integer.value[0] = dspk->lrsel;
-	else if (strstr(kcontrol->id.name, "Channel Select"))
-		ucontrol->value.integer.value[0] = dspk->ch_sel;
-	else if (strstr(kcontrol->id.name, "Mono To Stereo"))
-		ucontrol->value.integer.value[0] = dspk->mono_to_stereo;
-	else if (strstr(kcontrol->id.name, "Stereo To Mono"))
-		ucontrol->value.integer.value[0] = dspk->stereo_to_mono;
+	ucontrol->value.enumerated.item[0] = dspk->osr_val;
 
 	return 0;
 }
 
-static int tegra186_dspk_put_control(struct snd_kcontrol *kcontrol,
+static int tegra186_dspk_put_osr_val(struct snd_kcontrol *kcontrol,
 				     struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
 	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
-	int val = ucontrol->value.integer.value[0];
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dspk->osr_val)
+		return 0;
+
+	dspk->osr_val = value;
+
+	return 1;
+}
+
+static int tegra186_dspk_get_pol_sel(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+
+	ucontrol->value.enumerated.item[0] = dspk->lrsel;
+
+	return 0;
+}
+
+static int tegra186_dspk_put_pol_sel(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dspk->lrsel)
+		return 0;
+
+	dspk->lrsel = value;
+
+	return 1;
+}
+
+static int tegra186_dspk_get_ch_sel(struct snd_kcontrol *kcontrol,
+				    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+
+	ucontrol->value.enumerated.item[0] = dspk->ch_sel;
+
+	return 0;
+}
+
+static int tegra186_dspk_put_ch_sel(struct snd_kcontrol *kcontrol,
+				    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dspk->ch_sel)
+		return 0;
+
+	dspk->ch_sel = value;
+
+	return 1;
+}
+
+static int tegra186_dspk_get_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
 
-	if (strstr(kcontrol->id.name, "FIFO Threshold"))
-		dspk->rx_fifo_th = val;
-	else if (strstr(kcontrol->id.name, "OSR Value"))
-		dspk->osr_val = val;
-	else if (strstr(kcontrol->id.name, "LR Polarity Select"))
-		dspk->lrsel = val;
-	else if (strstr(kcontrol->id.name, "Channel Select"))
-		dspk->ch_sel = val;
-	else if (strstr(kcontrol->id.name, "Mono To Stereo"))
-		dspk->mono_to_stereo = val;
-	else if (strstr(kcontrol->id.name, "Stereo To Mono"))
-		dspk->stereo_to_mono = val;
+	ucontrol->value.enumerated.item[0] = dspk->mono_to_stereo;
 
 	return 0;
 }
 
+static int tegra186_dspk_put_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dspk->mono_to_stereo)
+		return 0;
+
+	dspk->mono_to_stereo = value;
+
+	return 1;
+}
+
+static int tegra186_dspk_get_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+
+	ucontrol->value.enumerated.item[0] = dspk->stereo_to_mono;
+
+	return 0;
+}
+
+static int tegra186_dspk_put_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol);
+	struct tegra186_dspk *dspk = snd_soc_component_get_drvdata(codec);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dspk->stereo_to_mono)
+		return 0;
+
+	dspk->stereo_to_mono = value;
+
+	return 1;
+}
+
 static int __maybe_unused tegra186_dspk_runtime_suspend(struct device *dev)
 {
 	struct tegra186_dspk *dspk = dev_get_drvdata(dev);
@@ -130,14 +240,14 @@
 		return -EINVAL;
 	}
 
-	cif_conf.client_bits = TEGRA_ACIF_BITS_24;
-
 	switch (params_format(params)) {
 	case SNDRV_PCM_FORMAT_S16_LE:
 		cif_conf.audio_bits = TEGRA_ACIF_BITS_16;
+		cif_conf.client_bits = TEGRA_ACIF_BITS_16;
 		break;
 	case SNDRV_PCM_FORMAT_S32_LE:
 		cif_conf.audio_bits = TEGRA_ACIF_BITS_32;
+		cif_conf.client_bits = TEGRA_ACIF_BITS_24;
 		break;
 	default:
 		dev_err(dev, "unsupported format!\n");
@@ -279,17 +389,19 @@
 static const struct snd_kcontrol_new tegrat186_dspk_controls[] = {
 	SOC_SINGLE_EXT("FIFO Threshold", SND_SOC_NOPM, 0,
 		       TEGRA186_DSPK_RX_FIFO_DEPTH - 1, 0,
-		       tegra186_dspk_get_control, tegra186_dspk_put_control),
+		       tegra186_dspk_get_fifo_th, tegra186_dspk_put_fifo_th),
 	SOC_ENUM_EXT("OSR Value", tegra186_dspk_osr_enum,
-		     tegra186_dspk_get_control, tegra186_dspk_put_control),
+		     tegra186_dspk_get_osr_val, tegra186_dspk_put_osr_val),
 	SOC_ENUM_EXT("LR Polarity Select", tegra186_dspk_lrsel_enum,
-		     tegra186_dspk_get_control, tegra186_dspk_put_control),
+		     tegra186_dspk_get_pol_sel, tegra186_dspk_put_pol_sel),
 	SOC_ENUM_EXT("Channel Select", tegra186_dspk_ch_sel_enum,
-		     tegra186_dspk_get_control, tegra186_dspk_put_control),
+		     tegra186_dspk_get_ch_sel, tegra186_dspk_put_ch_sel),
 	SOC_ENUM_EXT("Mono To Stereo", tegra186_dspk_mono_conv_enum,
-		     tegra186_dspk_get_control, tegra186_dspk_put_control),
+		     tegra186_dspk_get_mono_to_stereo,
+		     tegra186_dspk_put_mono_to_stereo),
 	SOC_ENUM_EXT("Stereo To Mono", tegra186_dspk_stereo_conv_enum,
-		     tegra186_dspk_get_control, tegra186_dspk_put_control),
+		     tegra186_dspk_get_stereo_to_mono,
+		     tegra186_dspk_put_stereo_to_mono),
 };
 
 static const struct snd_soc_component_driver tegra186_dspk_cmpnt = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra210_admaif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra210_admaif.c
@@ -424,46 +424,122 @@
 	.trigger	= tegra_admaif_trigger,
 };
 
-static int tegra_admaif_get_control(struct snd_kcontrol *kcontrol,
-				    struct snd_ctl_elem_value *ucontrol)
+static int tegra210_admaif_pget_mono_to_stereo(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
+	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
+
+	ucontrol->value.enumerated.item[0] =
+		admaif->mono_to_stereo[ADMAIF_TX_PATH][ec->reg];
+
+	return 0;
+}
+
+static int tegra210_admaif_pput_mono_to_stereo(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
+	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == admaif->mono_to_stereo[ADMAIF_TX_PATH][ec->reg])
+		return 0;
+
+	admaif->mono_to_stereo[ADMAIF_TX_PATH][ec->reg] = value;
+
+	return 1;
+}
+
+static int tegra210_admaif_cget_mono_to_stereo(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
+	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
+
+	ucontrol->value.enumerated.item[0] =
+		admaif->mono_to_stereo[ADMAIF_RX_PATH][ec->reg];
+
+	return 0;
+}
+
+static int tegra210_admaif_cput_mono_to_stereo(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
 	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == admaif->mono_to_stereo[ADMAIF_RX_PATH][ec->reg])
+		return 0;
+
+	admaif->mono_to_stereo[ADMAIF_RX_PATH][ec->reg] = value;
+
+	return 1;
+}
+
+static int tegra210_admaif_pget_stereo_to_mono(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
 	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
-	long *uctl_val = &ucontrol->value.integer.value[0];
+	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
 
-	if (strstr(kcontrol->id.name, "Playback Mono To Stereo"))
-		*uctl_val = admaif->mono_to_stereo[ADMAIF_TX_PATH][ec->reg];
-	else if (strstr(kcontrol->id.name, "Capture Mono To Stereo"))
-		*uctl_val = admaif->mono_to_stereo[ADMAIF_RX_PATH][ec->reg];
-	else if (strstr(kcontrol->id.name, "Playback Stereo To Mono"))
-		*uctl_val = admaif->stereo_to_mono[ADMAIF_TX_PATH][ec->reg];
-	else if (strstr(kcontrol->id.name, "Capture Stereo To Mono"))
-		*uctl_val = admaif->stereo_to_mono[ADMAIF_RX_PATH][ec->reg];
+	ucontrol->value.enumerated.item[0] =
+		admaif->stereo_to_mono[ADMAIF_TX_PATH][ec->reg];
 
 	return 0;
 }
 
-static int tegra_admaif_put_control(struct snd_kcontrol *kcontrol,
-				    struct snd_ctl_elem_value *ucontrol)
+static int tegra210_admaif_pput_stereo_to_mono(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
 	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == admaif->stereo_to_mono[ADMAIF_TX_PATH][ec->reg])
+		return 0;
+
+	admaif->stereo_to_mono[ADMAIF_TX_PATH][ec->reg] = value;
+
+	return 1;
+}
+
+static int tegra210_admaif_cget_stereo_to_mono(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
 	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
-	int value = ucontrol->value.integer.value[0];
+	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
 
-	if (strstr(kcontrol->id.name, "Playback Mono To Stereo"))
-		admaif->mono_to_stereo[ADMAIF_TX_PATH][ec->reg] = value;
-	else if (strstr(kcontrol->id.name, "Capture Mono To Stereo"))
-		admaif->mono_to_stereo[ADMAIF_RX_PATH][ec->reg] = value;
-	else if (strstr(kcontrol->id.name, "Playback Stereo To Mono"))
-		admaif->stereo_to_mono[ADMAIF_TX_PATH][ec->reg] = value;
-	else if (strstr(kcontrol->id.name, "Capture Stereo To Mono"))
-		admaif->stereo_to_mono[ADMAIF_RX_PATH][ec->reg] = value;
+	ucontrol->value.enumerated.item[0] =
+		admaif->stereo_to_mono[ADMAIF_RX_PATH][ec->reg];
 
 	return 0;
 }
 
+static int tegra210_admaif_cput_stereo_to_mono(struct snd_kcontrol *kcontrol,
+	struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *cmpnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra_admaif *admaif = snd_soc_component_get_drvdata(cmpnt);
+	struct soc_enum *ec = (struct soc_enum *)kcontrol->private_value;
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == admaif->stereo_to_mono[ADMAIF_RX_PATH][ec->reg])
+		return 0;
+
+	admaif->stereo_to_mono[ADMAIF_RX_PATH][ec->reg] = value;
+
+	return 1;
+}
+
 static int tegra_admaif_dai_probe(struct snd_soc_dai *dai)
 {
 	struct tegra_admaif *admaif = snd_soc_dai_get_drvdata(dai);
@@ -559,17 +635,21 @@
 }
 
 #define TEGRA_ADMAIF_CIF_CTRL(reg)					       \
-	NV_SOC_ENUM_EXT("ADMAIF" #reg " Playback Mono To Stereo", reg - 1,\
-			tegra_admaif_get_control, tegra_admaif_put_control,    \
+	NV_SOC_ENUM_EXT("ADMAIF" #reg " Playback Mono To Stereo", reg - 1,     \
+			tegra210_admaif_pget_mono_to_stereo,		       \
+			tegra210_admaif_pput_mono_to_stereo,		       \
 			tegra_admaif_mono_conv_text),			       \
-	NV_SOC_ENUM_EXT("ADMAIF" #reg " Playback Stereo To Mono", reg - 1,\
-			tegra_admaif_get_control, tegra_admaif_put_control,    \
+	NV_SOC_ENUM_EXT("ADMAIF" #reg " Playback Stereo To Mono", reg - 1,     \
+			tegra210_admaif_pget_stereo_to_mono,		       \
+			tegra210_admaif_pput_stereo_to_mono,		       \
 			tegra_admaif_stereo_conv_text),			       \
-	NV_SOC_ENUM_EXT("ADMAIF" #reg " Capture Mono To Stereo", reg - 1, \
-			tegra_admaif_get_control, tegra_admaif_put_control,    \
+	NV_SOC_ENUM_EXT("ADMAIF" #reg " Capture Mono To Stereo", reg - 1,      \
+			tegra210_admaif_cget_mono_to_stereo,		       \
+			tegra210_admaif_cput_mono_to_stereo,		       \
 			tegra_admaif_mono_conv_text),			       \
-	NV_SOC_ENUM_EXT("ADMAIF" #reg " Capture Stereo To Mono", reg - 1, \
-			tegra_admaif_get_control, tegra_admaif_put_control,    \
+	NV_SOC_ENUM_EXT("ADMAIF" #reg " Capture Stereo To Mono", reg - 1,      \
+			tegra210_admaif_cget_stereo_to_mono,		       \
+			tegra210_admaif_cput_stereo_to_mono,		       \
 			tegra_admaif_stereo_conv_text)
 
 static struct snd_kcontrol_new tegra210_admaif_controls[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra210_ahub.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra210_ahub.c
@@ -62,6 +62,7 @@
 	unsigned int *item = uctl->value.enumerated.item;
 	unsigned int value = e->values[item[0]];
 	unsigned int i, bit_pos, reg_idx = 0, reg_val = 0;
+	int change = 0;
 
 	if (item[0] >= e->items)
 		return -EINVAL;
@@ -86,12 +87,14 @@
 
 		/* Update widget power if state has changed */
 		if (snd_soc_component_test_bits(cmpnt, update[i].reg,
-						update[i].mask, update[i].val))
-			snd_soc_dapm_mux_update_power(dapm, kctl, item[0], e,
-						      &update[i]);
+						update[i].mask,
+						update[i].val))
+			change |= snd_soc_dapm_mux_update_power(dapm, kctl,
+								item[0], e,
+								&update[i]);
 	}
 
-	return 0;
+	return change;
 }
 
 static struct snd_soc_dai_driver tegra210_ahub_dais[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra210_dmic.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra210_dmic.c
@@ -156,51 +156,162 @@
 	return 0;
 }
 
-static int tegra210_dmic_get_control(struct snd_kcontrol *kcontrol,
+static int tegra210_dmic_get_boost_gain(struct snd_kcontrol *kcontrol,
+					struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+
+	ucontrol->value.integer.value[0] = dmic->boost_gain;
+
+	return 0;
+}
+
+static int tegra210_dmic_put_boost_gain(struct snd_kcontrol *kcontrol,
+					struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+	int value = ucontrol->value.integer.value[0];
+
+	if (value == dmic->boost_gain)
+		return 0;
+
+	dmic->boost_gain = value;
+
+	return 1;
+}
+
+static int tegra210_dmic_get_ch_select(struct snd_kcontrol *kcontrol,
+				       struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+
+	ucontrol->value.enumerated.item[0] = dmic->ch_select;
+
+	return 0;
+}
+
+static int tegra210_dmic_put_ch_select(struct snd_kcontrol *kcontrol,
+				       struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dmic->ch_select)
+		return 0;
+
+	dmic->ch_select = value;
+
+	return 1;
+}
+
+static int tegra210_dmic_get_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+
+	ucontrol->value.enumerated.item[0] = dmic->mono_to_stereo;
+
+	return 0;
+}
+
+static int tegra210_dmic_put_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dmic->mono_to_stereo)
+		return 0;
+
+	dmic->mono_to_stereo = value;
+
+	return 1;
+}
+
+static int tegra210_dmic_get_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+
+	ucontrol->value.enumerated.item[0] = dmic->stereo_to_mono;
+
+	return 0;
+}
+
+static int tegra210_dmic_put_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dmic->stereo_to_mono)
+		return 0;
+
+	dmic->stereo_to_mono = value;
+
+	return 1;
+}
+
+static int tegra210_dmic_get_osr_val(struct snd_kcontrol *kcontrol,
 				     struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
 	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
 
-	if (strstr(kcontrol->id.name, "Boost Gain Volume"))
-		ucontrol->value.integer.value[0] = dmic->boost_gain;
-	else if (strstr(kcontrol->id.name, "Channel Select"))
-		ucontrol->value.integer.value[0] = dmic->ch_select;
-	else if (strstr(kcontrol->id.name, "Mono To Stereo"))
-		ucontrol->value.integer.value[0] = dmic->mono_to_stereo;
-	else if (strstr(kcontrol->id.name, "Stereo To Mono"))
-		ucontrol->value.integer.value[0] = dmic->stereo_to_mono;
-	else if (strstr(kcontrol->id.name, "OSR Value"))
-		ucontrol->value.integer.value[0] = dmic->osr_val;
-	else if (strstr(kcontrol->id.name, "LR Polarity Select"))
-		ucontrol->value.integer.value[0] = dmic->lrsel;
+	ucontrol->value.enumerated.item[0] = dmic->osr_val;
 
 	return 0;
 }
 
-static int tegra210_dmic_put_control(struct snd_kcontrol *kcontrol,
+static int tegra210_dmic_put_osr_val(struct snd_kcontrol *kcontrol,
 				     struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
 	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
-	int value = ucontrol->value.integer.value[0];
+	unsigned int value = ucontrol->value.enumerated.item[0];
 
-	if (strstr(kcontrol->id.name, "Boost Gain Volume"))
-		dmic->boost_gain = value;
-	else if (strstr(kcontrol->id.name, "Channel Select"))
-		dmic->ch_select = ucontrol->value.integer.value[0];
-	else if (strstr(kcontrol->id.name, "Mono To Stereo"))
-		dmic->mono_to_stereo = value;
-	else if (strstr(kcontrol->id.name, "Stereo To Mono"))
-		dmic->stereo_to_mono = value;
-	else if (strstr(kcontrol->id.name, "OSR Value"))
-		dmic->osr_val = value;
-	else if (strstr(kcontrol->id.name, "LR Polarity Select"))
-		dmic->lrsel = value;
+	if (value == dmic->osr_val)
+		return 0;
+
+	dmic->osr_val = value;
+
+	return 1;
+}
+
+static int tegra210_dmic_get_pol_sel(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+
+	ucontrol->value.enumerated.item[0] = dmic->lrsel;
 
 	return 0;
 }
 
+static int tegra210_dmic_put_pol_sel(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_dmic *dmic = snd_soc_component_get_drvdata(comp);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == dmic->lrsel)
+		return 0;
+
+	dmic->lrsel = value;
+
+	return 1;
+}
+
 static const struct snd_soc_dai_ops tegra210_dmic_dai_ops = {
 	.hw_params	= tegra210_dmic_hw_params,
 };
@@ -287,19 +398,22 @@
 
 static const struct snd_kcontrol_new tegra210_dmic_controls[] = {
 	SOC_SINGLE_EXT("Boost Gain Volume", 0, 0, MAX_BOOST_GAIN, 0,
-		       tegra210_dmic_get_control, tegra210_dmic_put_control),
+		       tegra210_dmic_get_boost_gain,
+		       tegra210_dmic_put_boost_gain),
 	SOC_ENUM_EXT("Channel Select", tegra210_dmic_ch_enum,
-		     tegra210_dmic_get_control, tegra210_dmic_put_control),
+		     tegra210_dmic_get_ch_select, tegra210_dmic_put_ch_select),
 	SOC_ENUM_EXT("Mono To Stereo",
-		     tegra210_dmic_mono_conv_enum, tegra210_dmic_get_control,
-		     tegra210_dmic_put_control),
+		     tegra210_dmic_mono_conv_enum,
+		     tegra210_dmic_get_mono_to_stereo,
+		     tegra210_dmic_put_mono_to_stereo),
 	SOC_ENUM_EXT("Stereo To Mono",
-		     tegra210_dmic_stereo_conv_enum, tegra210_dmic_get_control,
-		     tegra210_dmic_put_control),
+		     tegra210_dmic_stereo_conv_enum,
+		     tegra210_dmic_get_stereo_to_mono,
+		     tegra210_dmic_put_stereo_to_mono),
 	SOC_ENUM_EXT("OSR Value", tegra210_dmic_osr_enum,
-		     tegra210_dmic_get_control, tegra210_dmic_put_control),
+		     tegra210_dmic_get_osr_val, tegra210_dmic_put_osr_val),
 	SOC_ENUM_EXT("LR Polarity Select", tegra210_dmic_lrsel_enum,
-		     tegra210_dmic_get_control, tegra210_dmic_put_control),
+		     tegra210_dmic_get_pol_sel, tegra210_dmic_put_pol_sel),
 };
 
 static const struct snd_soc_component_driver tegra210_dmic_compnt = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra210_i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra210_i2s.c
@@ -302,85 +302,235 @@
 	return 0;
 }
 
-static int tegra210_i2s_set_dai_bclk_ratio(struct snd_soc_dai *dai,
-					   unsigned int ratio)
+static int tegra210_i2s_get_loopback(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
 {
-	struct tegra210_i2s *i2s = snd_soc_dai_get_drvdata(dai);
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
 
-	i2s->bclk_ratio = ratio;
+	ucontrol->value.integer.value[0] = i2s->loopback;
 
 	return 0;
 }
 
-static int tegra210_i2s_get_control(struct snd_kcontrol *kcontrol,
-				    struct snd_ctl_elem_value *ucontrol)
+static int tegra210_i2s_put_loopback(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	int value = ucontrol->value.integer.value[0];
+
+	if (value == i2s->loopback)
+		return 0;
+
+	i2s->loopback = value;
+
+	regmap_update_bits(i2s->regmap, TEGRA210_I2S_CTRL, I2S_CTRL_LPBK_MASK,
+			   i2s->loopback << I2S_CTRL_LPBK_SHIFT);
+
+	return 1;
+}
+
+static int tegra210_i2s_get_fsync_width(struct snd_kcontrol *kcontrol,
+					struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
 	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
-	long *uctl_val = &ucontrol->value.integer.value[0];
 
-	if (strstr(kcontrol->id.name, "Loopback"))
-		*uctl_val = i2s->loopback;
-	else if (strstr(kcontrol->id.name, "FSYNC Width"))
-		*uctl_val = i2s->fsync_width;
-	else if (strstr(kcontrol->id.name, "Capture Stereo To Mono"))
-		*uctl_val = i2s->stereo_to_mono[I2S_TX_PATH];
-	else if (strstr(kcontrol->id.name, "Capture Mono To Stereo"))
-		*uctl_val = i2s->mono_to_stereo[I2S_TX_PATH];
-	else if (strstr(kcontrol->id.name, "Playback Stereo To Mono"))
-		*uctl_val = i2s->stereo_to_mono[I2S_RX_PATH];
-	else if (strstr(kcontrol->id.name, "Playback Mono To Stereo"))
-		*uctl_val = i2s->mono_to_stereo[I2S_RX_PATH];
-	else if (strstr(kcontrol->id.name, "Playback FIFO Threshold"))
-		*uctl_val = i2s->rx_fifo_th;
-	else if (strstr(kcontrol->id.name, "BCLK Ratio"))
-		*uctl_val = i2s->bclk_ratio;
+	ucontrol->value.integer.value[0] = i2s->fsync_width;
 
 	return 0;
 }
 
-static int tegra210_i2s_put_control(struct snd_kcontrol *kcontrol,
-				    struct snd_ctl_elem_value *ucontrol)
+static int tegra210_i2s_put_fsync_width(struct snd_kcontrol *kcontrol,
+					struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
 	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
 	int value = ucontrol->value.integer.value[0];
 
-	if (strstr(kcontrol->id.name, "Loopback")) {
-		i2s->loopback = value;
+	if (value == i2s->fsync_width)
+		return 0;
 
-		regmap_update_bits(i2s->regmap, TEGRA210_I2S_CTRL,
-				   I2S_CTRL_LPBK_MASK,
-				   i2s->loopback << I2S_CTRL_LPBK_SHIFT);
-
-	} else if (strstr(kcontrol->id.name, "FSYNC Width")) {
-		/*
-		 * Frame sync width is used only for FSYNC modes and not
-		 * applicable for LRCK modes. Reset value for this field is "0",
-		 * which means the width is one bit clock wide.
-		 * The width requirement may depend on the codec and in such
-		 * cases mixer control is used to update custom values. A value
-		 * of "N" here means, width is "N + 1" bit clock wide.
-		 */
-		i2s->fsync_width = value;
-
-		regmap_update_bits(i2s->regmap, TEGRA210_I2S_CTRL,
-				   I2S_CTRL_FSYNC_WIDTH_MASK,
-				   i2s->fsync_width << I2S_FSYNC_WIDTH_SHIFT);
-
-	} else if (strstr(kcontrol->id.name, "Capture Stereo To Mono")) {
-		i2s->stereo_to_mono[I2S_TX_PATH] = value;
-	} else if (strstr(kcontrol->id.name, "Capture Mono To Stereo")) {
-		i2s->mono_to_stereo[I2S_TX_PATH] = value;
-	} else if (strstr(kcontrol->id.name, "Playback Stereo To Mono")) {
-		i2s->stereo_to_mono[I2S_RX_PATH] = value;
-	} else if (strstr(kcontrol->id.name, "Playback Mono To Stereo")) {
-		i2s->mono_to_stereo[I2S_RX_PATH] = value;
-	} else if (strstr(kcontrol->id.name, "Playback FIFO Threshold")) {
-		i2s->rx_fifo_th = value;
-	} else if (strstr(kcontrol->id.name, "BCLK Ratio")) {
-		i2s->bclk_ratio = value;
-	}
+	i2s->fsync_width = value;
+
+	/*
+	 * Frame sync width is used only for FSYNC modes and not
+	 * applicable for LRCK modes. Reset value for this field is "0",
+	 * which means the width is one bit clock wide.
+	 * The width requirement may depend on the codec and in such
+	 * cases mixer control is used to update custom values. A value
+	 * of "N" here means, width is "N + 1" bit clock wide.
+	 */
+	regmap_update_bits(i2s->regmap, TEGRA210_I2S_CTRL,
+			   I2S_CTRL_FSYNC_WIDTH_MASK,
+			   i2s->fsync_width << I2S_FSYNC_WIDTH_SHIFT);
+
+	return 1;
+}
+
+static int tegra210_i2s_cget_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+
+	ucontrol->value.enumerated.item[0] = i2s->stereo_to_mono[I2S_TX_PATH];
+
+	return 0;
+}
+
+static int tegra210_i2s_cput_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == i2s->stereo_to_mono[I2S_TX_PATH])
+		return 0;
+
+	i2s->stereo_to_mono[I2S_TX_PATH] = value;
+
+	return 1;
+}
+
+static int tegra210_i2s_cget_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+
+	ucontrol->value.enumerated.item[0] = i2s->mono_to_stereo[I2S_TX_PATH];
+
+	return 0;
+}
+
+static int tegra210_i2s_cput_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == i2s->mono_to_stereo[I2S_TX_PATH])
+		return 0;
+
+	i2s->mono_to_stereo[I2S_TX_PATH] = value;
+
+	return 1;
+}
+
+static int tegra210_i2s_pget_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+
+	ucontrol->value.enumerated.item[0] = i2s->stereo_to_mono[I2S_RX_PATH];
+
+	return 0;
+}
+
+static int tegra210_i2s_pput_stereo_to_mono(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == i2s->stereo_to_mono[I2S_RX_PATH])
+		return 0;
+
+	i2s->stereo_to_mono[I2S_RX_PATH] = value;
+
+	return 1;
+}
+
+static int tegra210_i2s_pget_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+
+	ucontrol->value.enumerated.item[0] = i2s->mono_to_stereo[I2S_RX_PATH];
+
+	return 0;
+}
+
+static int tegra210_i2s_pput_mono_to_stereo(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	unsigned int value = ucontrol->value.enumerated.item[0];
+
+	if (value == i2s->mono_to_stereo[I2S_RX_PATH])
+		return 0;
+
+	i2s->mono_to_stereo[I2S_RX_PATH] = value;
+
+	return 1;
+}
+
+static int tegra210_i2s_pget_fifo_th(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+
+	ucontrol->value.integer.value[0] = i2s->rx_fifo_th;
+
+	return 0;
+}
+
+static int tegra210_i2s_pput_fifo_th(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	int value = ucontrol->value.integer.value[0];
+
+	if (value == i2s->rx_fifo_th)
+		return 0;
+
+	i2s->rx_fifo_th = value;
+
+	return 1;
+}
+
+static int tegra210_i2s_get_bclk_ratio(struct snd_kcontrol *kcontrol,
+				       struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+
+	ucontrol->value.integer.value[0] = i2s->bclk_ratio;
+
+	return 0;
+}
+
+static int tegra210_i2s_put_bclk_ratio(struct snd_kcontrol *kcontrol,
+				       struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *compnt = snd_soc_kcontrol_component(kcontrol);
+	struct tegra210_i2s *i2s = snd_soc_component_get_drvdata(compnt);
+	int value = ucontrol->value.integer.value[0];
+
+	if (value == i2s->bclk_ratio)
+		return 0;
+
+	i2s->bclk_ratio = value;
+
+	return 1;
+}
+
+static int tegra210_i2s_set_dai_bclk_ratio(struct snd_soc_dai *dai,
+					   unsigned int ratio)
+{
+	struct tegra210_i2s *i2s = snd_soc_dai_get_drvdata(dai);
+
+	i2s->bclk_ratio = ratio;
 
 	return 0;
 }
@@ -598,22 +748,28 @@
 			tegra210_i2s_stereo_conv_text);
 
 static const struct snd_kcontrol_new tegra210_i2s_controls[] = {
-	SOC_SINGLE_EXT("Loopback", 0, 0, 1, 0, tegra210_i2s_get_control,
-		       tegra210_i2s_put_control),
-	SOC_SINGLE_EXT("FSYNC Width", 0, 0, 255, 0, tegra210_i2s_get_control,
-		       tegra210_i2s_put_control),
+	SOC_SINGLE_EXT("Loopback", 0, 0, 1, 0, tegra210_i2s_get_loopback,
+		       tegra210_i2s_put_loopback),
+	SOC_SINGLE_EXT("FSYNC Width", 0, 0, 255, 0,
+		       tegra210_i2s_get_fsync_width,
+		       tegra210_i2s_put_fsync_width),
 	SOC_ENUM_EXT("Capture Stereo To Mono", tegra210_i2s_stereo_conv_enum,
-		     tegra210_i2s_get_control, tegra210_i2s_put_control),
+		     tegra210_i2s_cget_stereo_to_mono,
+		     tegra210_i2s_cput_stereo_to_mono),
 	SOC_ENUM_EXT("Capture Mono To Stereo", tegra210_i2s_mono_conv_enum,
-		     tegra210_i2s_get_control, tegra210_i2s_put_control),
+		     tegra210_i2s_cget_mono_to_stereo,
+		     tegra210_i2s_cput_mono_to_stereo),
 	SOC_ENUM_EXT("Playback Stereo To Mono", tegra210_i2s_stereo_conv_enum,
-		     tegra210_i2s_get_control, tegra210_i2s_put_control),
+		     tegra210_i2s_pget_mono_to_stereo,
+		     tegra210_i2s_pput_mono_to_stereo),
 	SOC_ENUM_EXT("Playback Mono To Stereo", tegra210_i2s_mono_conv_enum,
-		     tegra210_i2s_get_control, tegra210_i2s_put_control),
+		     tegra210_i2s_pget_stereo_to_mono,
+		     tegra210_i2s_pput_stereo_to_mono),
 	SOC_SINGLE_EXT("Playback FIFO Threshold", 0, 0, I2S_RX_FIFO_DEPTH - 1,
-		       0, tegra210_i2s_get_control, tegra210_i2s_put_control),
-	SOC_SINGLE_EXT("BCLK Ratio", 0, 0, INT_MAX, 0, tegra210_i2s_get_control,
-		       tegra210_i2s_put_control),
+		       0, tegra210_i2s_pget_fifo_th, tegra210_i2s_pput_fifo_th),
+	SOC_SINGLE_EXT("BCLK Ratio", 0, 0, INT_MAX, 0,
+		       tegra210_i2s_get_bclk_ratio,
+		       tegra210_i2s_put_bclk_ratio),
 };
 
 static const struct snd_soc_dapm_widget tegra210_i2s_widgets[] = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra_asoc_machine.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra_asoc_machine.c
@@ -116,16 +116,24 @@
 	SOC_DAPM_PIN_SWITCH("Headset Mic"),
 	SOC_DAPM_PIN_SWITCH("Internal Mic 1"),
 	SOC_DAPM_PIN_SWITCH("Internal Mic 2"),
+	SOC_DAPM_PIN_SWITCH("Headphones"),
+	SOC_DAPM_PIN_SWITCH("Mic Jack"),
 };
 
 int tegra_asoc_machine_init(struct snd_soc_pcm_runtime *rtd)
 {
 	struct snd_soc_card *card = rtd->card;
 	struct tegra_machine *machine = snd_soc_card_get_drvdata(card);
+	const char *jack_name;
 	int err;
 
 	if (machine->gpiod_hp_det && machine->asoc->add_hp_jack) {
-		err = snd_soc_card_jack_new(card, "Headphones Jack",
+		if (machine->asoc->hp_jack_name)
+			jack_name = machine->asoc->hp_jack_name;
+		else
+			jack_name = "Headphones Jack";
+
+		err = snd_soc_card_jack_new(card, jack_name,
 					    SND_JACK_HEADPHONE,
 					    &tegra_machine_hp_jack,
 					    tegra_machine_hp_jack_pins,
@@ -341,9 +349,34 @@
 	return np;
 }
 
+static void tegra_machine_unregister_codec(void *pdev)
+{
+	platform_device_unregister(pdev);
+}
+
+static int tegra_machine_register_codec(struct device *dev, const char *name)
+{
+	struct platform_device *pdev;
+	int err;
+
+	if (!name)
+		return 0;
+
+	pdev = platform_device_register_simple(name, -1, NULL, 0);
+	if (IS_ERR(pdev))
+		return PTR_ERR(pdev);
+
+	err = devm_add_action_or_reset(dev, tegra_machine_unregister_codec,
+				       pdev);
+	if (err)
+		return err;
+
+	return 0;
+}
+
 int tegra_asoc_machine_probe(struct platform_device *pdev)
 {
-	struct device_node *np_codec, *np_i2s;
+	struct device_node *np_codec, *np_i2s, *np_ac97;
 	const struct tegra_asoc_data *asoc;
 	struct device *dev = &pdev->dev;
 	struct tegra_machine *machine;
@@ -404,17 +437,30 @@
 			return err;
 	}
 
-	np_codec = tegra_machine_parse_phandle(dev, "nvidia,audio-codec");
-	if (IS_ERR(np_codec))
-		return PTR_ERR(np_codec);
-
-	np_i2s = tegra_machine_parse_phandle(dev, "nvidia,i2s-controller");
-	if (IS_ERR(np_i2s))
-		return PTR_ERR(np_i2s);
-
-	card->dai_link->cpus->of_node = np_i2s;
-	card->dai_link->codecs->of_node = np_codec;
-	card->dai_link->platforms->of_node = np_i2s;
+	if (asoc->set_ac97) {
+		err = tegra_machine_register_codec(dev, asoc->codec_dev_name);
+		if (err)
+			return err;
+
+		np_ac97 = tegra_machine_parse_phandle(dev, "nvidia,ac97-controller");
+		if (IS_ERR(np_ac97))
+			return PTR_ERR(np_ac97);
+
+		card->dai_link->cpus->of_node = np_ac97;
+		card->dai_link->platforms->of_node = np_ac97;
+	} else {
+		np_codec = tegra_machine_parse_phandle(dev, "nvidia,audio-codec");
+		if (IS_ERR(np_codec))
+			return PTR_ERR(np_codec);
+
+		np_i2s = tegra_machine_parse_phandle(dev, "nvidia,i2s-controller");
+		if (IS_ERR(np_i2s))
+			return PTR_ERR(np_i2s);
+
+		card->dai_link->cpus->of_node = np_i2s;
+		card->dai_link->codecs->of_node = np_codec;
+		card->dai_link->platforms->of_node = np_i2s;
+	}
 
 	if (asoc->add_common_controls) {
 		card->controls = tegra_machine_controls;
@@ -589,6 +635,7 @@
 static const struct tegra_asoc_data tegra_wm9712_data = {
 	.card = &snd_soc_tegra_wm9712,
 	.add_common_dapm_widgets = true,
+	.codec_dev_name = "wm9712-codec",
 	.set_ac97 = true,
 };
 
@@ -619,6 +666,7 @@
 static const struct tegra_asoc_data tegra_max98090_data = {
 	.mclk_rate = tegra_machine_mclk_rate_12mhz,
 	.card = &snd_soc_tegra_max98090,
+	.hp_jack_name = "Headphones",
 	.add_common_dapm_widgets = true,
 	.add_common_controls = true,
 	.add_common_snd_ops = true,
@@ -686,6 +734,7 @@
 };
 
 static struct snd_soc_card snd_soc_tegra_trimslice = {
+	.name = "tegra-trimslice",
 	.components = "codec:tlv320aic23",
 	.dai_link = &tegra_tlv320aic23_dai,
 	.num_links = 1,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra_asoc_machine.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra_asoc_machine.h
@@ -13,6 +13,8 @@
 
 struct tegra_asoc_data {
 	unsigned int (*mclk_rate)(unsigned int srate);
+	const char *codec_dev_name;
+	const char *hp_jack_name;
 	struct snd_soc_card *card;
 	unsigned int mclk_id;
 	bool hp_jack_gpio_active_low;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/tegra/tegra_audio_graph_card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/tegra/tegra_audio_graph_card.c
@@ -10,6 +10,7 @@
 #include <linux/platform_device.h>
 #include <sound/graph_card.h>
 #include <sound/pcm_params.h>
+#include <sound/soc-dai.h>
 
 #define MAX_PLLA_OUT0_DIV 128
 
@@ -44,6 +45,21 @@
 	unsigned int plla_out0_rates[NUM_RATE_TYPE];
 };
 
+static bool need_clk_update(struct snd_soc_dai *dai)
+{
+	if (snd_soc_dai_is_dummy(dai) ||
+	    !dai->driver->ops ||
+	    !dai->driver->name)
+		return false;
+
+	if (strstr(dai->driver->name, "I2S") ||
+	    strstr(dai->driver->name, "DMIC") ||
+	    strstr(dai->driver->name, "DSPK"))
+		return true;
+
+	return false;
+}
+
 /* Setup PLL clock as per the given sample rate */
 static int tegra_audio_graph_update_pll(struct snd_pcm_substream *substream,
 					struct snd_pcm_hw_params *params)
@@ -140,19 +156,7 @@
 	struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
 	int err;
 
-	/*
-	 * This gets called for each DAI link (FE or BE) when DPCM is used.
-	 * We may not want to update PLLA rate for each call. So PLLA update
-	 * must be restricted to external I/O links (I2S, DMIC or DSPK) since
-	 * they actually depend on it. I/O modules update their clocks in
-	 * hw_param() of their respective component driver and PLLA rate
-	 * update here helps them to derive appropriate rates.
-	 *
-	 * TODO: When more HW accelerators get added (like sample rate
-	 * converter, volume gain controller etc., which don't really
-	 * depend on PLLA) we need a better way to filter here.
-	 */
-	if (cpu_dai->driver->ops && rtd->dai_link->no_pcm) {
+	if (need_clk_update(cpu_dai)) {
 		err = tegra_audio_graph_update_pll(substream, params);
 		if (err)
 			return err;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/ti/ams-delta.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/ti/ams-delta.c
@@ -303,7 +303,7 @@
 static void cx81801_close(struct tty_struct *tty)
 {
 	struct snd_soc_component *component = tty->disc_data;
-	struct snd_soc_dapm_context *dapm = &component->card->dapm;
+	struct snd_soc_dapm_context *dapm;
 
 	del_timer_sync(&cx81801_timer);
 
@@ -315,6 +315,8 @@
 
 	v253_ops.close(tty);
 
+	dapm = &component->card->dapm;
+
 	/* Revert back to default audio input/output constellation */
 	snd_soc_dapm_mutex_lock(dapm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/ti/davinci-i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/ti/davinci-i2s.c
@@ -708,7 +708,9 @@
 	dev->clk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(dev->clk))
 		return -ENODEV;
-	clk_enable(dev->clk);
+	ret = clk_enable(dev->clk);
+	if (ret)
+		goto err_put_clk;
 
 	dev->dev = &pdev->dev;
 	dev_set_drvdata(&pdev->dev, dev);
@@ -730,6 +732,7 @@
 	snd_soc_unregister_component(&pdev->dev);
 err_release_clk:
 	clk_disable(dev->clk);
+err_put_clk:
 	clk_put(dev->clk);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/ti/davinci-mcasp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/ti/davinci-mcasp.c
@@ -1472,10 +1472,11 @@
 {
 	struct snd_interval *period_size = hw_param_interval(params,
 						SNDRV_PCM_HW_PARAM_PERIOD_SIZE);
+	u8 numevt = *((u8 *)rule->private);
 	struct snd_interval frames;
 
 	snd_interval_any(&frames);
-	frames.min = 64;
+	frames.min = numevt;
 	frames.integer = 1;
 
 	return snd_interval_refine(period_size, &frames);
@@ -1490,6 +1491,7 @@
 	u32 max_channels = 0;
 	int i, dir, ret;
 	int tdm_slots = mcasp->tdm_slots;
+	u8 *numevt;
 
 	/* Do not allow more then one stream per direction */
 	if (mcasp->substreams[substream->stream])
@@ -1589,9 +1591,12 @@
 			return ret;
 	}
 
+	numevt = (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ?
+			 &mcasp->txnumevt :
+			 &mcasp->rxnumevt;
 	snd_pcm_hw_rule_add(substream->runtime, 0,
 			    SNDRV_PCM_HW_PARAM_PERIOD_SIZE,
-			    davinci_mcasp_hw_rule_min_periodsize, NULL,
+			    davinci_mcasp_hw_rule_min_periodsize, numevt,
 			    SNDRV_PCM_HW_PARAM_PERIOD_SIZE, -1);
 
 	return 0;
@@ -2423,12 +2428,6 @@
 
 	mcasp_reparent_fck(pdev);
 
-	ret = devm_snd_soc_register_component(&pdev->dev, &davinci_mcasp_component,
-					      &davinci_mcasp_dai[mcasp->op_mode], 1);
-
-	if (ret != 0)
-		goto err;
-
 	ret = davinci_mcasp_get_dma_type(mcasp);
 	switch (ret) {
 	case PCM_EDMA:
@@ -2455,6 +2454,12 @@
 		goto err;
 	}
 
+	ret = devm_snd_soc_register_component(&pdev->dev, &davinci_mcasp_component,
+					      &davinci_mcasp_dai[mcasp->op_mode], 1);
+
+	if (ret != 0)
+		goto err;
+
 no_audio:
 	ret = davinci_mcasp_init_gpiochip(mcasp);
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/ti/j721e-evm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/ti/j721e-evm.c
@@ -182,6 +182,8 @@
 		clk_id = J721E_CLK_PARENT_48000;
 	else if (!(rate % 11025) && priv->pll_rates[J721E_CLK_PARENT_44100])
 		clk_id = J721E_CLK_PARENT_44100;
+	else if (!(rate % 11025) && priv->pll_rates[J721E_CLK_PARENT_48000])
+		clk_id = J721E_CLK_PARENT_48000;
 	else
 		return ret;
 
@@ -634,17 +636,18 @@
 	codec_node = of_parse_phandle(node, "ti,cpb-codec", 0);
 	if (!codec_node) {
 		dev_err(priv->dev, "CPB codec node is not provided\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_dai_node;
 	}
 
 	domain = &priv->audio_domains[J721E_AUDIO_DOMAIN_CPB];
 	ret = j721e_get_clocks(priv->dev, &domain->codec, "cpb-codec-scki");
 	if (ret)
-		return ret;
+		goto put_codec_node;
 
 	ret = j721e_get_clocks(priv->dev, &domain->mcasp, "cpb-mcasp-auxclk");
 	if (ret)
-		return ret;
+		goto put_codec_node;
 
 	/*
 	 * Common Processor Board, two links
@@ -654,8 +657,10 @@
 	comp_count = 6;
 	compnent = devm_kzalloc(priv->dev, comp_count * sizeof(*compnent),
 				GFP_KERNEL);
-	if (!compnent)
-		return -ENOMEM;
+	if (!compnent) {
+		ret = -ENOMEM;
+		goto put_codec_node;
+	}
 
 	comp_idx = 0;
 	priv->dai_links[*link_idx].cpus = &compnent[comp_idx++];
@@ -706,6 +711,12 @@
 	(*conf_idx)++;
 
 	return 0;
+
+put_codec_node:
+	of_node_put(codec_node);
+put_dai_node:
+	of_node_put(dai_node);
+	return ret;
 }
 
 static int j721e_soc_probe_ivi(struct j721e_priv *priv, int *link_idx,
@@ -730,23 +741,25 @@
 	codeca_node = of_parse_phandle(node, "ti,ivi-codec-a", 0);
 	if (!codeca_node) {
 		dev_err(priv->dev, "IVI codec-a node is not provided\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto put_dai_node;
 	}
 
 	codecb_node = of_parse_phandle(node, "ti,ivi-codec-b", 0);
 	if (!codecb_node) {
 		dev_warn(priv->dev, "IVI codec-b node is not provided\n");
-		return 0;
+		ret = 0;
+		goto put_codeca_node;
 	}
 
 	domain = &priv->audio_domains[J721E_AUDIO_DOMAIN_IVI];
 	ret = j721e_get_clocks(priv->dev, &domain->codec, "ivi-codec-scki");
 	if (ret)
-		return ret;
+		goto put_codecb_node;
 
 	ret = j721e_get_clocks(priv->dev, &domain->mcasp, "ivi-mcasp-auxclk");
 	if (ret)
-		return ret;
+		goto put_codecb_node;
 
 	/*
 	 * IVI extension, two links
@@ -758,8 +771,10 @@
 	comp_count = 8;
 	compnent = devm_kzalloc(priv->dev, comp_count * sizeof(*compnent),
 				GFP_KERNEL);
-	if (!compnent)
-		return -ENOMEM;
+	if (!compnent) {
+		ret = -ENOMEM;
+		goto put_codecb_node;
+	}
 
 	comp_idx = 0;
 	priv->dai_links[*link_idx].cpus = &compnent[comp_idx++];
@@ -820,6 +835,15 @@
 	(*conf_idx)++;
 
 	return 0;
+
+
+put_codecb_node:
+	of_node_put(codecb_node);
+put_codeca_node:
+	of_node_put(codeca_node);
+put_dai_node:
+	of_node_put(dai_node);
+	return ret;
 }
 
 static int j721e_soc_probe(struct platform_device *pdev)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/ti/omap-hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/ti/omap-hdmi.c
@@ -353,11 +353,7 @@
 	if (!card)
 		return -ENOMEM;
 
-	card->name = devm_kasprintf(dev, GFP_KERNEL,
-				    "HDMI %s", dev_name(ad->dssdev));
-	if (!card->name)
-		return -ENOMEM;
-
+	card->name = "HDMI";
 	card->owner = THIS_MODULE;
 	card->dai_link =
 		devm_kzalloc(dev, sizeof(*(card->dai_link)), GFP_KERNEL);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/ti/omap-mcbsp.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/ti/omap-mcbsp.c
@@ -74,14 +74,16 @@
 		return -EINVAL;
 	}
 
-	pm_runtime_put_sync(mcbsp->dev);
+	if (mcbsp->active)
+		pm_runtime_put_sync(mcbsp->dev);
 
 	r = clk_set_parent(mcbsp->fclk, fck_src);
 	if (r)
 		dev_err(mcbsp->dev, "CLKS: could not clk_set_parent() to %s\n",
 			src);
 
-	pm_runtime_get_sync(mcbsp->dev);
+	if (mcbsp->active)
+		pm_runtime_get_sync(mcbsp->dev);
 
 	clk_put(fck_src);
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/uniphier/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/uniphier/Kconfig
@@ -23,7 +23,6 @@
 	tristate "UniPhier LD11/LD20 Device Driver"
 	depends on SND_SOC_UNIPHIER
 	select SND_SOC_UNIPHIER_AIO
-	select SND_SOC_UNIPHIER_AIO_DMA
 	help
 	  This adds ASoC driver for Socionext UniPhier LD11/LD20
 	  input and output that can be used with other codecs.
@@ -34,7 +33,6 @@
 	tristate "UniPhier PXs2 Device Driver"
 	depends on SND_SOC_UNIPHIER
 	select SND_SOC_UNIPHIER_AIO
-	select SND_SOC_UNIPHIER_AIO_DMA
 	help
 	  This adds ASoC driver for Socionext UniPhier PXs2
 	  input and output that can be used with other codecs.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/Kconfig
@@ -1,4 +1,19 @@
 # SPDX-License-Identifier: GPL-2.0-only
+config SND_SOC_XILINX_DP
+	tristate "Audio support for the the Xilinx DisplayPort"
+	select SND_DMAENGINE_PCM
+	select SND_SOC_GENERIC_DMAENGINE_PCM
+	help
+	  Audio support the for Xilinx DisplayPort.
+
+config SND_SOC_XILINX_SDI
+	tristate "Audio support for the the Xilinx SDI"
+	depends on DRM_XLNX_SDI
+	depends on VIDEO_XILINX_SDIRXSS
+	help
+	  Select this option to enable Xilinx SDI Audio.This enables
+	  SDI audio playback and capture using xilinx soft IP
+
 config SND_SOC_XILINX_I2S
 	tristate "Audio support for the Xilinx I2S"
 	help
@@ -7,6 +22,7 @@
 	  mode, IP receives audio in AES format, extracts PCM and sends
 	  PCM data. In receiver mode, IP receives PCM audio and
 	  encapsulates PCM in AES format and sends AES data.
+	  I2S playback and capture using xilinx soft IP
 
 config SND_SOC_XILINX_AUDIO_FORMATTER
 	tristate "Audio support for the Xilinx audio formatter"
@@ -19,5 +35,14 @@
 	tristate "Audio support for the Xilinx SPDIF"
 	help
 	  Select this option to enable Xilinx SPDIF Audio.
-	  This provides playback and capture of SPDIF audio in
-	  AES format.
+	  Enabling this provides one of the component required in ASoC
+	  audio pipeline.
+	  This supports playback and capture usecases.
+
+config SND_SOC_XILINX_PL_SND_CARD
+	tristate "Audio support for the the Xilinx PL sound card"
+	depends on SND_SOC_XILINX_AUDIO_FORMATTER || SND_SOC_XILINX_I2S || SND_SOC_XILINX_SDI
+	help
+	  Select this option to enable Xilinx PL sound card
+	  support. This enables sound card using xilinx soft IPs
+	  in audio pipeline.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/Makefile
@@ -1,7 +1,11 @@
 # SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_SND_SOC_XILINX_DP) += xilinx-dp-pcm.o
+obj-$(CONFIG_SND_SOC_XILINX_DP) += xilinx-dp-codec.o
+obj-$(CONFIG_SND_SOC_XILINX_DP) += xilinx-dp-card.o
+obj-$(CONFIG_SND_SOC_XILINX_SDI) += xlnx_sdi_audio.o
 snd-soc-xlnx-i2s-objs      := xlnx_i2s.o
 obj-$(CONFIG_SND_SOC_XILINX_I2S) += snd-soc-xlnx-i2s.o
 snd-soc-xlnx-formatter-pcm-objs := xlnx_formatter_pcm.o
 obj-$(CONFIG_SND_SOC_XILINX_AUDIO_FORMATTER) += snd-soc-xlnx-formatter-pcm.o
-snd-soc-xlnx-spdif-objs := xlnx_spdif.o
-obj-$(CONFIG_SND_SOC_XILINX_SPDIF) += snd-soc-xlnx-spdif.o
+obj-$(CONFIG_SND_SOC_XILINX_SPDIF) += xlnx_spdif.o
+obj-$(CONFIG_SND_SOC_XILINX_PL_SND_CARD) += xlnx_pl_snd_card.o
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xilinx-dp-card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xilinx-dp-card.c
@@ -0,0 +1,123 @@
+/*
+ * Xilinx DisplayPort SoC Sound Card support
+ *
+ *  Copyright (C) 2015 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyunk@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <sound/soc.h>
+
+static int xilinx_dp_startup(struct snd_pcm_substream *substream)
+{
+	struct snd_pcm_runtime *runtime = substream->runtime;
+
+	snd_pcm_hw_constraint_step(runtime, 0,
+				   SNDRV_PCM_HW_PARAM_PERIOD_BYTES, 256);
+	return 0;
+}
+
+static const struct snd_soc_ops xilinx_dp_ops = {
+	.startup	= xilinx_dp_startup,
+};
+
+SND_SOC_DAILINK_DEFS(xilinx_dp0,
+		DAILINK_COMP_ARRAY(COMP_CPU("xilinx-dp-snd-codec-dai")),
+		DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xilinx-dp-snd-codec-dai")),
+		DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xilinx_dp1,
+		DAILINK_COMP_ARRAY(COMP_CPU("xilinx-dp-snd-codec-dai")),
+		DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xilinx-dp-snd-codec-dai")),
+		DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+static struct snd_soc_dai_link xilinx_dp_dai_links[] = {
+	{
+		.name		= "xilinx-dp0",
+		.stream_name	= "xilinx-dp0",
+		SND_SOC_DAILINK_REG(xilinx_dp0),
+		.ops		= &xilinx_dp_ops,
+	},
+	{
+		.name		= "xilinx-dp1",
+		.stream_name	= "xilinx-dp1",
+		SND_SOC_DAILINK_REG(xilinx_dp1),
+		.ops		= &xilinx_dp_ops,
+	},
+
+};
+
+static struct snd_soc_card xilinx_dp_card = {
+	.name		= "DisplayPort monitor",
+	.owner		= THIS_MODULE,
+	.dai_link	= xilinx_dp_dai_links,
+	.num_links	= 2,
+};
+
+static int xilinx_dp_probe(struct platform_device *pdev)
+{
+	struct snd_soc_card *card = &xilinx_dp_card;
+	struct device_node *node = pdev->dev.of_node;
+	struct device_node *codec, *pcm;
+	int ret;
+
+	card->dev = &pdev->dev;
+
+	codec = of_parse_phandle(node, "xlnx,dp-snd-codec", 0);
+	if (!codec)
+		return -ENODEV;
+
+	pcm = of_parse_phandle(node, "xlnx,dp-snd-pcm", 0);
+	if (!pcm)
+		return -ENODEV;
+	xilinx_dp_dai_links[0].platforms->of_node = pcm;
+	xilinx_dp_dai_links[0].cpus->of_node = codec;
+	xilinx_dp_dai_links[0].codecs->of_node = codec;
+
+	pcm = of_parse_phandle(node, "xlnx,dp-snd-pcm", 1);
+	if (!pcm)
+		return -ENODEV;
+	xilinx_dp_dai_links[1].platforms->of_node = pcm;
+	xilinx_dp_dai_links[1].cpus->of_node = codec;
+	xilinx_dp_dai_links[1].codecs->of_node = codec;
+
+	ret = devm_snd_soc_register_card(&pdev->dev, card);
+	if (ret)
+		return ret;
+
+	dev_info(&pdev->dev, "Xilinx DisplayPort Sound Card probed\n");
+
+	return 0;
+}
+
+static const struct of_device_id xilinx_dp_of_match[] = {
+	{ .compatible = "xlnx,dp-snd-card", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xilinx_dp_of_match);
+
+static struct platform_driver xilinx_dp_aud_driver = {
+	.driver	= {
+		.name		= "xilinx-dp-snd-card",
+		.of_match_table	= xilinx_dp_of_match,
+		.pm		= &snd_soc_pm_ops,
+	},
+	.probe	= xilinx_dp_probe,
+};
+module_platform_driver(xilinx_dp_aud_driver);
+
+MODULE_DESCRIPTION("Xilinx DisplayPort Sound Card module");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xilinx-dp-codec.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xilinx-dp-codec.c
@@ -0,0 +1,254 @@
+/*
+ * Xilinx DisplayPort Sound Codec support
+ *
+ *  Copyright (C) 2015 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyunk@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+#include <sound/soc.h>
+
+#define ZYNQMP_DISP_AUD_CH_STATUS		0x8
+#define ZYNQMP_DISP_AUD_CH_STATUS_44K		0x0
+#define ZYNQMP_DISP_AUD_CH_STATUS_48K		0x2000000
+#define ZYNQMP_DISP_AUD_SMPL_RATE_44K		44100
+#define ZYNQMP_DISP_AUD_SMPL_RATE_48K		48000
+#define ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK	512
+
+/**
+ * struct xilinx_dp_codec - DisplayPort codec
+ * @aud_clk: audio clock
+ * @aud_base: base address for DP audio
+ * @dev: DP audio device
+ */
+struct xilinx_dp_codec {
+	struct clk *aud_clk;
+	struct regmap *aud_base;
+	struct device *dev;
+};
+
+struct xilinx_dp_codec_fmt {
+	unsigned long rate;
+	unsigned int snd_rate;
+};
+
+static int dp_codec_hw_params(struct snd_pcm_substream *substream,
+			      struct snd_pcm_hw_params *params,
+			      struct snd_soc_dai *socdai)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	struct xilinx_dp_codec *codec =
+		snd_soc_dai_get_drvdata(asoc_rtd_to_cpu(rtd, 0));
+	unsigned long rate;
+	int ret;
+
+	u32 sample_rate = params_rate(params);
+
+	if (sample_rate != ZYNQMP_DISP_AUD_SMPL_RATE_48K &&
+	    sample_rate != ZYNQMP_DISP_AUD_SMPL_RATE_44K)
+		return -EINVAL;
+
+	clk_disable_unprepare(codec->aud_clk);
+	ret = clk_set_rate(codec->aud_clk,
+			   sample_rate * ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK);
+	if (ret) {
+		dev_err(codec->dev, "can't set aud_clk to %u err:%d\n",
+			sample_rate * ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK, ret);
+		return ret;
+	}
+	clk_prepare_enable(codec->aud_clk);
+	rate = clk_get_rate(codec->aud_clk);
+
+	/* Ignore some offset +- 10 */
+	if (abs(sample_rate * ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK - rate) > 10) {
+		dev_err(codec->dev, "aud_clk offset is higher: %ld\n",
+			sample_rate * ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK - rate);
+		ret = -EINVAL;
+		goto err_clk;
+	}
+
+	if (sample_rate == ZYNQMP_DISP_AUD_SMPL_RATE_48K)
+		regmap_write(codec->aud_base, ZYNQMP_DISP_AUD_CH_STATUS,
+			     ZYNQMP_DISP_AUD_CH_STATUS_48K);
+	else
+		regmap_write(codec->aud_base, ZYNQMP_DISP_AUD_CH_STATUS,
+			     ZYNQMP_DISP_AUD_CH_STATUS_44K);
+
+	return 0;
+
+err_clk:
+	clk_disable_unprepare(codec->aud_clk);
+	return ret;
+}
+
+static const struct snd_soc_dai_ops dp_codec_dai_ops = {
+	.hw_params	= dp_codec_hw_params,
+};
+
+static struct snd_soc_dai_driver xilinx_dp_codec_dai = {
+	.name		= "xilinx-dp-snd-codec-dai",
+	.ops		= &dp_codec_dai_ops,
+	.playback	= {
+		.channels_min	= 2,
+		.channels_max	= 2,
+		.rates		= SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000,
+		.formats	= SNDRV_PCM_FMTBIT_S16_LE,
+	},
+};
+
+static const struct xilinx_dp_codec_fmt rates[] = {
+	{
+		.rate	= ZYNQMP_DISP_AUD_SMPL_RATE_48K *
+			  ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK,
+		.snd_rate = SNDRV_PCM_RATE_48000
+	},
+	{
+		.rate	= ZYNQMP_DISP_AUD_SMPL_RATE_44K *
+			  ZYNQMP_DISP_AUD_SMPL_RATE_TO_CLK,
+		.snd_rate = SNDRV_PCM_RATE_44100
+	}
+};
+
+static const struct snd_soc_component_driver xilinx_dp_component_driver = {
+	.idle_bias_on		= 1,
+	.use_pmdown_time	= 1,
+	.endianness		= 1,
+	.non_legacy_dai_naming	= 1,
+};
+
+static int xilinx_dp_codec_probe(struct platform_device *pdev)
+{
+	struct xilinx_dp_codec *codec;
+	unsigned int i;
+	unsigned long rate;
+	int ret;
+
+	codec = devm_kzalloc(&pdev->dev, sizeof(*codec), GFP_KERNEL);
+	if (!codec)
+		return -ENOMEM;
+
+	codec->aud_clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(codec->aud_clk))
+		return PTR_ERR(codec->aud_clk);
+
+	ret = clk_prepare_enable(codec->aud_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable the aud_clk\n");
+		return ret;
+	}
+
+	codec->aud_base =
+		syscon_regmap_lookup_by_phandle(pdev->dev.parent->of_node,
+						"xlnx,dpaud-reg");
+	if (IS_ERR(codec->aud_base))
+		return PTR_ERR(codec->aud_base);
+
+	codec->dev = &pdev->dev;
+
+	for (i = 0; i < ARRAY_SIZE(rates); i++) {
+		clk_disable_unprepare(codec->aud_clk);
+		ret = clk_set_rate(codec->aud_clk, rates[i].rate);
+		clk_prepare_enable(codec->aud_clk);
+		if (ret)
+			continue;
+
+		rate = clk_get_rate(codec->aud_clk);
+		/* Ignore some offset +- 10 */
+		if (abs(rates[i].rate - rate) < 10)
+			break;
+		ret = -EINVAL;
+	}
+
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to get required clock freq\n");
+		goto error_clk;
+	}
+
+	ret = devm_snd_soc_register_component(&pdev->dev,
+					      &xilinx_dp_component_driver,
+					      &xilinx_dp_codec_dai, 1);
+	if (ret)
+		goto error_clk;
+
+	platform_set_drvdata(pdev, codec);
+	dev_set_drvdata(&pdev->dev, codec);
+
+	dev_info(&pdev->dev, "Xilinx DisplayPort Sound Codec probed\n");
+
+	return 0;
+
+error_clk:
+	clk_disable_unprepare(codec->aud_clk);
+	return ret;
+}
+
+static int xilinx_dp_codec_dev_remove(struct platform_device *pdev)
+{
+	struct xilinx_dp_codec *codec = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(codec->aud_clk);
+
+	return 0;
+}
+
+static int __maybe_unused xilinx_dp_codec_pm_suspend(struct device *dev)
+{
+	struct xilinx_dp_codec *codec = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(codec->aud_clk);
+
+	return 0;
+}
+
+static int __maybe_unused xilinx_dp_codec_pm_resume(struct device *dev)
+{
+	struct xilinx_dp_codec *codec = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_prepare_enable(codec->aud_clk);
+	if (ret)
+		dev_err(dev, "failed to enable the aud_clk\n");
+
+	return ret;
+}
+
+static const struct dev_pm_ops xilinx_dp_codec_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xilinx_dp_codec_pm_suspend,
+				xilinx_dp_codec_pm_resume)
+};
+
+static const struct of_device_id xilinx_dp_codec_of_match[] = {
+	{ .compatible = "xlnx,dp-snd-codec", },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xilinx_dp_codec_of_match);
+
+static struct platform_driver xilinx_dp_codec_driver = {
+	.driver	= {
+		.name		= "xilinx-dp-snd-codec",
+		.of_match_table	= xilinx_dp_codec_of_match,
+		.pm		= &xilinx_dp_codec_pm_ops,
+	},
+	.probe	= xilinx_dp_codec_probe,
+	.remove	= xilinx_dp_codec_dev_remove,
+};
+module_platform_driver(xilinx_dp_codec_driver);
+
+MODULE_DESCRIPTION("Xilinx DisplayPort Sound Codec module");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xilinx-dp-pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xilinx-dp-pcm.c
@@ -0,0 +1,88 @@
+/*
+ * Xilinx DisplayPort Sound PCM support
+ *
+ *  Copyright (C) 2015 Xilinx, Inc.
+ *
+ *  Author: Hyun Woo Kwon <hyunk@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <sound/dmaengine_pcm.h>
+#include <sound/pcm.h>
+#include <sound/soc.h>
+
+#define DP_PCM_NAME_0 "zynqmp_dp_snd_pcm0"
+#define DP_PCM_NAME_1 "zynqmp_dp_snd_pcm1"
+
+static const struct snd_pcm_hardware xilinx_pcm_hw = {
+	.info			= SNDRV_PCM_INFO_MMAP |
+				  SNDRV_PCM_INFO_MMAP_VALID |
+				  SNDRV_PCM_INFO_INTERLEAVED |
+				  SNDRV_PCM_INFO_PAUSE |
+				  SNDRV_PCM_INFO_RESUME |
+				  SNDRV_PCM_INFO_NO_PERIOD_WAKEUP,
+	.buffer_bytes_max	= 128 * 1024,
+	.period_bytes_min	= 256,
+	.period_bytes_max	= 1024 * 1024,
+	.periods_min		= 2,
+	.periods_max		= 256,
+};
+
+static const struct snd_dmaengine_pcm_config xilinx_dmaengine_pcm_config = {
+	.pcm_hardware = &xilinx_pcm_hw,
+	.prealloc_buffer_size = 64 * 1024,
+};
+
+static int xilinx_dp_pcm_probe(struct platform_device *pdev)
+{
+	int ret;
+
+	if (of_device_is_compatible(pdev->dev.of_node, "xlnx,dp-snd-pcm0"))
+		dev_set_name(&pdev->dev, DP_PCM_NAME_0);
+	else if (of_device_is_compatible(pdev->dev.of_node, "xlnx,dp-snd-pcm1"))
+		dev_set_name(&pdev->dev, DP_PCM_NAME_1);
+	else
+		dev_set_name(&pdev->dev, pdev->dev.of_node->name);
+
+	pdev->name = dev_name(&pdev->dev);
+	ret = devm_snd_dmaengine_pcm_register(&pdev->dev,
+					      &xilinx_dmaengine_pcm_config, 0);
+	if (ret)
+		return ret;
+
+	dev_info(&pdev->dev, "Xilinx DisplayPort Sound PCM probed\n");
+
+	return 0;
+}
+
+static const struct of_device_id xilinx_dp_pcm_of_match[] = {
+	{ .compatible = "xlnx,dp-snd-pcm", },
+	{ .compatible = "xlnx,dp-snd-pcm0", },
+	{ .compatible = "xlnx,dp-snd-pcm1", },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xilinx_dp_pcm_of_match);
+
+static struct platform_driver xilinx_dp_pcm_driver = {
+	.driver	= {
+		.name		= "xilinx-dp-snd-pcm",
+		.of_match_table	= xilinx_dp_pcm_of_match,
+	},
+	.probe	= xilinx_dp_pcm_probe,
+};
+module_platform_driver(xilinx_dp_pcm_driver);
+
+MODULE_DESCRIPTION("Xilinx DisplayPort Sound PCM module");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xlnx_formatter_pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xlnx_formatter_pcm.c
@@ -1,22 +1,26 @@
 // SPDX-License-Identifier: GPL-2.0
-//
-// Xilinx ASoC audio formatter support
-//
-// Copyright (C) 2018 Xilinx, Inc.
-//
-// Author: Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>
+/*
+ * Xilinx ASoC audio formatter support
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ */
 
 #include <linux/clk.h>
+#include <linux/dma-mapping.h>
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
+#include <linux/platform_device.h>
 #include <linux/sizes.h>
 
 #include <sound/asoundef.h>
 #include <sound/soc.h>
 #include <sound/pcm_params.h>
 
+#include "xlnx_snd_common.h"
+
 #define DRV_NAME "xlnx_formatter_pcm"
 
 #define XLNX_S2MM_OFFSET	0
@@ -37,6 +41,7 @@
 #define XLNX_AUD_XFER_COUNT	0x28
 #define XLNX_AUD_CH_STS_START	0x2C
 #define XLNX_BYTES_PER_CH	0x44
+#define XLNX_AUD_ALIGN_BYTES	64
 
 #define AUD_STS_IOC_IRQ_MASK	BIT(31)
 #define AUD_STS_CH_STS_MASK	BIT(29)
@@ -56,7 +61,9 @@
 #define CFG_S2MM_XFER_SHIFT	29
 #define CFG_S2MM_PKG_MASK	BIT(28)
 
+#define AUD_CTRL_DATA_WIDTH_MASK	GENMASK(18, 16)
 #define AUD_CTRL_DATA_WIDTH_SHIFT	16
+#define AUD_CTRL_ACTIVE_CH_MASK		GENMASK(22, 19)
 #define AUD_CTRL_ACTIVE_CH_SHIFT	19
 #define PERIOD_CFG_PERIODS_SHIFT	16
 
@@ -66,12 +73,22 @@
 #define PERIOD_BYTES_MAX	(50 * 1024)
 #define XLNX_PARAM_UNKNOWN	0
 
-enum bit_depth {
-	BIT_DEPTH_8,
-	BIT_DEPTH_16,
-	BIT_DEPTH_20,
-	BIT_DEPTH_24,
-	BIT_DEPTH_32,
+static const struct snd_pcm_hardware xlnx_pcm_hardware = {
+	.info = SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
+		SNDRV_PCM_INFO_BATCH | SNDRV_PCM_INFO_PAUSE |
+		SNDRV_PCM_INFO_RESUME,
+	.formats = SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE |
+		   SNDRV_PCM_FMTBIT_S24_LE,
+	.channels_min = 2,
+	.channels_max = 8,
+	.rates = SNDRV_PCM_RATE_8000_192000,
+	.rate_min = 8000,
+	.rate_max = 192000,
+	.buffer_bytes_max = PERIODS_MAX * PERIOD_BYTES_MAX,
+	.period_bytes_min = PERIOD_BYTES_MIN,
+	.period_bytes_max = PERIOD_BYTES_MAX,
+	.periods_min = PERIODS_MIN,
+	.periods_max = PERIODS_MAX,
 };
 
 struct xlnx_pcm_drv_data {
@@ -82,7 +99,13 @@
 	int mm2s_irq;
 	struct snd_pcm_substream *play_stream;
 	struct snd_pcm_substream *capture_stream;
+	struct platform_device *pdev;
+	struct device_node *nodes[XLNX_MAX_PATHS];
 	struct clk *axi_clk;
+	unsigned int sysclk;
+	struct clk *mm2s_axis_clk;
+	struct clk *s2mm_axis_clk;
+	struct clk *aud_mclk;
 };
 
 /*
@@ -101,22 +124,12 @@
 	u64 buffer_size;
 };
 
-static const struct snd_pcm_hardware xlnx_pcm_hardware = {
-	.info = SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-		SNDRV_PCM_INFO_BATCH | SNDRV_PCM_INFO_PAUSE |
-		SNDRV_PCM_INFO_RESUME,
-	.formats = SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE |
-		   SNDRV_PCM_FMTBIT_S24_LE,
-	.channels_min = 2,
-	.channels_max = 2,
-	.rates = SNDRV_PCM_RATE_8000_192000,
-	.rate_min = 8000,
-	.rate_max = 192000,
-	.buffer_bytes_max = PERIODS_MAX * PERIOD_BYTES_MAX,
-	.period_bytes_min = PERIOD_BYTES_MIN,
-	.period_bytes_max = PERIOD_BYTES_MAX,
-	.periods_min = PERIODS_MIN,
-	.periods_max = PERIODS_MAX,
+enum bit_depth {
+	BIT_DEPTH_8,
+	BIT_DEPTH_16,
+	BIT_DEPTH_20,
+	BIT_DEPTH_24,
+	BIT_DEPTH_32,
 };
 
 enum {
@@ -246,16 +259,16 @@
 {
 	u32 val, retries = 0;
 
-	val = readl(mmio_base + XLNX_AUD_CTRL);
+	val = ioread32(mmio_base + XLNX_AUD_CTRL);
 	val |= AUD_CTRL_RESET_MASK;
-	writel(val, mmio_base + XLNX_AUD_CTRL);
+	iowrite32(val, mmio_base + XLNX_AUD_CTRL);
 
-	val = readl(mmio_base + XLNX_AUD_CTRL);
+	val = ioread32(mmio_base + XLNX_AUD_CTRL);
 	/* Poll for maximum timeout of approximately 100ms (1 * 100)*/
 	while ((val & AUD_CTRL_RESET_MASK) && (retries < 100)) {
 		mdelay(1);
 		retries++;
-		val = readl(mmio_base + XLNX_AUD_CTRL);
+		val = ioread32(mmio_base + XLNX_AUD_CTRL);
 	}
 	if (val & AUD_CTRL_RESET_MASK)
 		return -ENODEV;
@@ -267,12 +280,12 @@
 {
 	u32 val;
 
-	val = readl(mmio_base + XLNX_AUD_CTRL);
+	val = ioread32(mmio_base + XLNX_AUD_CTRL);
 	val &= ~AUD_CTRL_IOC_IRQ_MASK;
 	if (stream == SNDRV_PCM_STREAM_CAPTURE)
 		val &= ~AUD_CTRL_TOUT_IRQ_MASK;
 
-	writel(val, mmio_base + XLNX_AUD_CTRL);
+	iowrite32(val, mmio_base + XLNX_AUD_CTRL);
 }
 
 static irqreturn_t xlnx_mm2s_irq_handler(int irq, void *arg)
@@ -283,9 +296,9 @@
 	struct xlnx_pcm_drv_data *adata = dev_get_drvdata(dev);
 
 	reg = adata->mmio + XLNX_MM2S_OFFSET + XLNX_AUD_STS;
-	val = readl(reg);
+	val = ioread32(reg);
 	if (val & AUD_STS_IOC_IRQ_MASK) {
-		writel(val & AUD_STS_IOC_IRQ_MASK, reg);
+		iowrite32(val & AUD_STS_IOC_IRQ_MASK, reg);
 		if (adata->play_stream)
 			snd_pcm_period_elapsed(adata->play_stream);
 		return IRQ_HANDLED;
@@ -302,9 +315,9 @@
 	struct xlnx_pcm_drv_data *adata = dev_get_drvdata(dev);
 
 	reg = adata->mmio + XLNX_S2MM_OFFSET + XLNX_AUD_STS;
-	val = readl(reg);
+	val = ioread32(reg);
 	if (val & AUD_STS_IOC_IRQ_MASK) {
-		writel(val & AUD_STS_IOC_IRQ_MASK, reg);
+		iowrite32(val & AUD_STS_IOC_IRQ_MASK, reg);
 		if (adata->capture_stream)
 			snd_pcm_period_elapsed(adata->capture_stream);
 		return IRQ_HANDLED;
@@ -313,6 +326,15 @@
 	return IRQ_NONE;
 }
 
+static int xlnx_formatter_set_sysclk(struct snd_soc_component *component,
+				     int clk_id, int source, unsigned int freq, int dir)
+{
+	struct xlnx_pcm_drv_data *adata = dev_get_drvdata(component->dev);
+
+	adata->sysclk = freq;
+	return 0;
+}
+
 static int xlnx_formatter_pcm_open(struct snd_soc_component *component,
 				   struct snd_pcm_substream *substream)
 {
@@ -321,7 +343,12 @@
 	u32 ch_count_mask, ch_count_shift, data_xfer_mode, data_xfer_shift;
 	struct xlnx_pcm_stream_param *stream_data;
 	struct snd_pcm_runtime *runtime = substream->runtime;
-	struct xlnx_pcm_drv_data *adata = dev_get_drvdata(component->dev);
+	struct xlnx_pcm_drv_data *adata;
+
+	if (!component)
+		return -ENODEV;
+
+	adata = dev_get_drvdata(component->dev);
 
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
 	    !adata->mm2s_presence)
@@ -353,10 +380,12 @@
 		adata->capture_stream = substream;
 	}
 
-	val = readl(adata->mmio + XLNX_AUD_CORE_CONFIG);
+	val = ioread32(adata->mmio + XLNX_AUD_CORE_CONFIG);
 
 	if (!(val & data_format_mode))
 		stream_data->interleaved = true;
+	else
+		stream_data->interleaved = false;
 
 	stream_data->xfer_mode = (val & data_xfer_mode) >> data_xfer_shift;
 	stream_data->ch_limit = (val & ch_count_mask) >> ch_count_shift;
@@ -368,19 +397,37 @@
 	snd_soc_set_runtime_hwparams(substream, &xlnx_pcm_hardware);
 	runtime->private_data = stream_data;
 
-	/* Resize the period size divisible by 64 */
+	/* Resize the period bytes as divisible by 64 */
 	err = snd_pcm_hw_constraint_step(runtime, 0,
-					 SNDRV_PCM_HW_PARAM_PERIOD_BYTES, 64);
+					 SNDRV_PCM_HW_PARAM_PERIOD_BYTES,
+					 XLNX_AUD_ALIGN_BYTES);
 	if (err) {
 		dev_err(component->dev,
-			"unable to set constraint on period bytes\n");
+			"Unable to set constraint on period bytes\n");
+		return err;
+	}
+	/* Resize the buffer bytes as divisible by 64 */
+	err = snd_pcm_hw_constraint_step(runtime, 0,
+					 SNDRV_PCM_HW_PARAM_BUFFER_BYTES,
+					 XLNX_AUD_ALIGN_BYTES);
+	if (err) {
+		dev_err(component->dev,
+			"Unable to set constraint on buffer bytes\n");
+		return err;
+	}
+	/* Set periods as integer multiple */
+	err = snd_pcm_hw_constraint_integer(runtime,
+					    SNDRV_PCM_HW_PARAM_PERIODS);
+	if (err < 0) {
+		dev_err(component->dev,
+			"Unable to set constraint on periods to be integer\n");
 		return err;
 	}
 
 	/* enable DMA IOC irq */
-	val = readl(stream_data->mmio + XLNX_AUD_CTRL);
+	val = ioread32(stream_data->mmio + XLNX_AUD_CTRL);
 	val |= AUD_CTRL_IOC_IRQ_MASK;
-	writel(val, stream_data->mmio + XLNX_AUD_CTRL);
+	iowrite32(val, stream_data->mmio + XLNX_AUD_CTRL);
 
 	return 0;
 }
@@ -392,6 +439,9 @@
 	struct xlnx_pcm_stream_param *stream_data =
 			substream->runtime->private_data;
 
+	if (!component)
+		return -ENODEV;
+
 	ret = xlnx_formatter_pcm_reset(stream_data->mmio);
 	if (ret) {
 		dev_err(component->dev, "audio formatter reset failed\n");
@@ -412,7 +462,7 @@
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	struct xlnx_pcm_stream_param *stream_data = runtime->private_data;
 
-	pos = readl(stream_data->mmio + XLNX_AUD_XFER_COUNT);
+	pos = ioread32(stream_data->mmio + XLNX_AUD_XFER_COUNT);
 
 	if (pos >= stream_data->buffer_size)
 		pos = 0;
@@ -424,24 +474,53 @@
 					struct snd_pcm_substream *substream,
 					struct snd_pcm_hw_params *params)
 {
-	u32 low, high, active_ch, val, bytes_per_ch, bits_per_sample;
+	u32 low, high, active_ch, val, bits_per_sample, bytes_per_ch;
 	u32 aes_reg1_val, aes_reg2_val;
+	int status;
 	u64 size;
+	struct pl_card_data *prv;
 	struct snd_pcm_runtime *runtime = substream->runtime;
 	struct xlnx_pcm_stream_param *stream_data = runtime->private_data;
+	struct xlnx_pcm_drv_data *adata;
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+
+	if (!component)
+		return -ENODEV;
+
+	adata = dev_get_drvdata(component->dev);
 
 	active_ch = params_channels(params);
 	if (active_ch > stream_data->ch_limit)
 		return -EINVAL;
 
+	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
+	    adata->sysclk) {
+		unsigned int mclk_fs = adata->sysclk / params_rate(params);
+
+		if (adata->sysclk % params_rate(params) != 0) {
+			dev_warn(component->dev, "sysclk %u not divisible by rate %u\n",
+				 adata->sysclk, params_rate(params));
+			return -EINVAL;
+		}
+
+		writel(mclk_fs, stream_data->mmio + XLNX_AUD_FS_MULTIPLIER);
+	}
+
 	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE &&
-	    stream_data->xfer_mode == AES_TO_PCM) {
-		val = readl(stream_data->mmio + XLNX_AUD_STS);
+	    stream_data->xfer_mode == AES_TO_PCM &&
+	    ((strstr(adata->nodes[XLNX_CAPTURE]->name, "hdmi")) ||
+	    (strstr(adata->nodes[XLNX_CAPTURE]->name, "sdi")) ||
+	    (strstr(adata->nodes[XLNX_CAPTURE]->name, "dp")))) {
+		/*
+		 * If formatter is in AES_PCM mode for HDMI/SDI capture path,
+		 * parse AES header
+		 */
+		val = ioread32(stream_data->mmio + XLNX_AUD_STS);
 		if (val & AUD_STS_CH_STS_MASK) {
-			aes_reg1_val = readl(stream_data->mmio +
-					     XLNX_AUD_CH_STS_START);
-			aes_reg2_val = readl(stream_data->mmio +
-					     XLNX_AUD_CH_STS_START + 0x4);
+			aes_reg1_val = ioread32(stream_data->mmio +
+					 XLNX_AUD_CH_STS_START);
+			aes_reg2_val = ioread32(stream_data->mmio +
+					 XLNX_AUD_CH_STS_START + 0x4);
 
 			xlnx_parse_aes_params(aes_reg1_val, aes_reg2_val,
 					      component->dev);
@@ -449,15 +528,19 @@
 	}
 
 	size = params_buffer_bytes(params);
+	status = snd_pcm_lib_malloc_pages(substream, size);
+	if (status < 0)
+		return status;
 
 	stream_data->buffer_size = size;
 
 	low = lower_32_bits(runtime->dma_addr);
 	high = upper_32_bits(runtime->dma_addr);
-	writel(low, stream_data->mmio + XLNX_AUD_BUFF_ADDR_LSB);
-	writel(high, stream_data->mmio + XLNX_AUD_BUFF_ADDR_MSB);
+	iowrite32(low, stream_data->mmio + XLNX_AUD_BUFF_ADDR_LSB);
+	iowrite32(high, stream_data->mmio + XLNX_AUD_BUFF_ADDR_MSB);
 
-	val = readl(stream_data->mmio + XLNX_AUD_CTRL);
+	val = ioread32(stream_data->mmio + XLNX_AUD_CTRL);
+	val &= ~AUD_CTRL_DATA_WIDTH_MASK;
 	bits_per_sample = params_width(params);
 	switch (bits_per_sample) {
 	case 8:
@@ -475,25 +558,35 @@
 	case 32:
 		val |= (BIT_DEPTH_32 << AUD_CTRL_DATA_WIDTH_SHIFT);
 		break;
-	default:
-		return -EINVAL;
 	}
 
+	val &= ~AUD_CTRL_ACTIVE_CH_MASK;
 	val |= active_ch << AUD_CTRL_ACTIVE_CH_SHIFT;
-	writel(val, stream_data->mmio + XLNX_AUD_CTRL);
+	iowrite32(val, stream_data->mmio + XLNX_AUD_CTRL);
 
 	val = (params_periods(params) << PERIOD_CFG_PERIODS_SHIFT)
 		| params_period_bytes(params);
-	writel(val, stream_data->mmio + XLNX_AUD_PERIOD_CONFIG);
+	iowrite32(val, stream_data->mmio + XLNX_AUD_PERIOD_CONFIG);
 	bytes_per_ch = DIV_ROUND_UP(params_period_bytes(params), active_ch);
-	writel(bytes_per_ch, stream_data->mmio + XLNX_BYTES_PER_CH);
+	iowrite32(bytes_per_ch, stream_data->mmio + XLNX_BYTES_PER_CH);
+
+	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
+		prv = snd_soc_card_get_drvdata(rtd->card);
+		iowrite32(prv->mclk_ratio,
+			  stream_data->mmio + XLNX_AUD_FS_MULTIPLIER);
+	}
 
 	return 0;
 }
 
+static int xlnx_formatter_pcm_hw_free(struct snd_soc_component *component,
+				      struct snd_pcm_substream *substream)
+{
+	return snd_pcm_lib_free_pages(substream);
+}
+
 static int xlnx_formatter_pcm_trigger(struct snd_soc_component *component,
-				      struct snd_pcm_substream *substream,
-				      int cmd)
+				      struct snd_pcm_substream *substream, int cmd)
 {
 	u32 val;
 	struct xlnx_pcm_stream_param *stream_data =
@@ -503,16 +596,16 @@
 	case SNDRV_PCM_TRIGGER_START:
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
 	case SNDRV_PCM_TRIGGER_RESUME:
-		val = readl(stream_data->mmio + XLNX_AUD_CTRL);
+		val = ioread32(stream_data->mmio + XLNX_AUD_CTRL);
 		val |= AUD_CTRL_DMA_EN_MASK;
-		writel(val, stream_data->mmio + XLNX_AUD_CTRL);
+		iowrite32(val, stream_data->mmio + XLNX_AUD_CTRL);
 		break;
 	case SNDRV_PCM_TRIGGER_STOP:
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
 	case SNDRV_PCM_TRIGGER_SUSPEND:
-		val = readl(stream_data->mmio + XLNX_AUD_CTRL);
+		val = ioread32(stream_data->mmio + XLNX_AUD_CTRL);
 		val &= ~AUD_CTRL_DMA_EN_MASK;
-		writel(val, stream_data->mmio + XLNX_AUD_CTRL);
+		iowrite32(val, stream_data->mmio + XLNX_AUD_CTRL);
 		break;
 	}
 
@@ -522,27 +615,167 @@
 static int xlnx_formatter_pcm_new(struct snd_soc_component *component,
 				  struct snd_soc_pcm_runtime *rtd)
 {
-	snd_pcm_set_managed_buffer_all(rtd->pcm,
-			SNDRV_DMA_TYPE_DEV, component->dev,
-			xlnx_pcm_hardware.buffer_bytes_max,
-			xlnx_pcm_hardware.buffer_bytes_max);
+	if (!component)
+		return -ENODEV;
+
+	snd_pcm_lib_preallocate_pages_for_all(rtd->pcm,
+					      SNDRV_DMA_TYPE_DEV,
+					      component->dev,
+					      xlnx_pcm_hardware.buffer_bytes_max,
+					      xlnx_pcm_hardware.buffer_bytes_max);
 	return 0;
 }
 
 static const struct snd_soc_component_driver xlnx_asoc_component = {
-	.name		= DRV_NAME,
-	.open		= xlnx_formatter_pcm_open,
-	.close		= xlnx_formatter_pcm_close,
-	.hw_params	= xlnx_formatter_pcm_hw_params,
-	.trigger	= xlnx_formatter_pcm_trigger,
-	.pointer	= xlnx_formatter_pcm_pointer,
-	.pcm_construct	= xlnx_formatter_pcm_new,
+	.name = DRV_NAME,
+	.set_sysclk = xlnx_formatter_set_sysclk,
+	.open = xlnx_formatter_pcm_open,
+	.close = xlnx_formatter_pcm_close,
+	.hw_params = xlnx_formatter_pcm_hw_params,
+	.hw_free = xlnx_formatter_pcm_hw_free,
+	.trigger = xlnx_formatter_pcm_trigger,
+	.pointer = xlnx_formatter_pcm_pointer,
+	.pcm_construct = xlnx_formatter_pcm_new,
 };
 
+static int configure_mm2s(struct xlnx_pcm_drv_data *aud_drv_data,
+			  struct platform_device *pdev)
+{
+	int ret;
+	struct device *dev = &pdev->dev;
+
+	aud_drv_data->mm2s_axis_clk = devm_clk_get(dev, "m_axis_mm2s_aclk");
+	if (IS_ERR(aud_drv_data->mm2s_axis_clk)) {
+		ret = PTR_ERR(aud_drv_data->mm2s_axis_clk);
+		dev_err(dev, "failed to get m_axis_mm2s_aclk(%d)\n", ret);
+		return ret;
+	}
+	ret = clk_prepare_enable(aud_drv_data->mm2s_axis_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable m_axis_mm2s_aclk(%d)\n", ret);
+		return ret;
+	}
+
+	aud_drv_data->aud_mclk = devm_clk_get(dev, "aud_mclk");
+	if (IS_ERR(aud_drv_data->aud_mclk)) {
+		ret = PTR_ERR(aud_drv_data->aud_mclk);
+		dev_err(dev, "failed to get aud_mclk(%d)\n", ret);
+		goto axis_clk_err;
+	}
+	ret = clk_prepare_enable(aud_drv_data->aud_mclk);
+	if (ret) {
+		dev_err(dev, "failed to enable aud_mclk(%d)\n", ret);
+		goto axis_clk_err;
+	}
+
+	aud_drv_data->mm2s_irq = platform_get_irq_byname(pdev,
+							 "irq_mm2s");
+	if (aud_drv_data->mm2s_irq < 0) {
+		ret = aud_drv_data->mm2s_irq;
+		goto mm2s_err;
+	}
+	ret = devm_request_irq(dev, aud_drv_data->mm2s_irq,
+			       xlnx_mm2s_irq_handler, 0,
+			       "xlnx_formatter_pcm_mm2s_irq",
+			       dev);
+	if (ret) {
+		dev_err(dev, "xlnx audio mm2s irq request failed\n");
+		goto mm2s_err;
+	}
+	ret = xlnx_formatter_pcm_reset(aud_drv_data->mmio +
+				       XLNX_MM2S_OFFSET);
+	if (ret) {
+		dev_err(dev, "audio formatter reset failed\n");
+		goto mm2s_err;
+	}
+	xlnx_formatter_disable_irqs(aud_drv_data->mmio +
+				    XLNX_MM2S_OFFSET,
+				    SNDRV_PCM_STREAM_PLAYBACK);
+
+	aud_drv_data->nodes[XLNX_PLAYBACK] =
+		of_parse_phandle(dev->of_node, "xlnx,tx", 0);
+	if (!aud_drv_data->nodes[XLNX_PLAYBACK])
+		dev_err(dev, "tx node not found\n");
+	else
+		dev_info(dev,
+			 "sound card device will use DAI link: %s\n",
+			 (aud_drv_data->nodes[XLNX_PLAYBACK])->name);
+	of_node_put(aud_drv_data->nodes[XLNX_PLAYBACK]);
+
+	aud_drv_data->mm2s_presence = true;
+	return 0;
+
+mm2s_err:
+	clk_disable_unprepare(aud_drv_data->aud_mclk);
+axis_clk_err:
+	clk_disable_unprepare(aud_drv_data->mm2s_axis_clk);
+
+	return ret;
+}
+
+static int configure_s2mm(struct xlnx_pcm_drv_data *aud_drv_data,
+			  struct platform_device *pdev)
+{
+	int ret;
+	struct device *dev = &pdev->dev;
+
+	aud_drv_data->s2mm_axis_clk = devm_clk_get(dev, "s_axis_s2mm_aclk");
+	if (IS_ERR(aud_drv_data->s2mm_axis_clk)) {
+		ret = PTR_ERR(aud_drv_data->s2mm_axis_clk);
+		dev_err(dev, "failed to get s_axis_s2mm_aclk(%d)\n", ret);
+		return ret;
+	}
+	ret = clk_prepare_enable(aud_drv_data->s2mm_axis_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable s_axis_s2mm_aclk(%d)\n", ret);
+		return ret;
+	}
+
+	aud_drv_data->s2mm_irq = platform_get_irq_byname(pdev, "irq_s2mm");
+	if (aud_drv_data->s2mm_irq < 0) {
+		ret = aud_drv_data->s2mm_irq;
+		goto s2mm_err;
+	}
+	ret = devm_request_irq(dev, aud_drv_data->s2mm_irq,
+			       xlnx_s2mm_irq_handler, 0,
+			       "xlnx_formatter_pcm_s2mm_irq",
+			       dev);
+	if (ret) {
+		dev_err(dev, "xlnx audio s2mm irq request failed\n");
+		goto s2mm_err;
+	}
+	ret = xlnx_formatter_pcm_reset(aud_drv_data->mmio +
+				       XLNX_S2MM_OFFSET);
+	if (ret) {
+		dev_err(dev, "audio formatter reset failed\n");
+		goto s2mm_err;
+	}
+	xlnx_formatter_disable_irqs(aud_drv_data->mmio +
+				    XLNX_S2MM_OFFSET,
+				    SNDRV_PCM_STREAM_CAPTURE);
+
+	aud_drv_data->nodes[XLNX_CAPTURE] =
+		of_parse_phandle(dev->of_node, "xlnx,rx", 0);
+	if (!aud_drv_data->nodes[XLNX_CAPTURE])
+		dev_err(dev, "rx node not found\n");
+	else
+		dev_info(dev, "sound card device will use DAI link: %s\n",
+			 (aud_drv_data->nodes[XLNX_CAPTURE])->name);
+	of_node_put(aud_drv_data->nodes[XLNX_CAPTURE]);
+
+	aud_drv_data->s2mm_presence = true;
+	return 0;
+
+s2mm_err:
+	clk_disable_unprepare(aud_drv_data->s2mm_axis_clk);
+	return ret;
+}
+
 static int xlnx_formatter_pcm_probe(struct platform_device *pdev)
 {
 	int ret;
 	u32 val;
+	size_t pdata_size;
 	struct xlnx_pcm_drv_data *aud_drv_data;
 	struct device *dev = &pdev->dev;
 
@@ -550,6 +783,12 @@
 	if (!aud_drv_data)
 		return -ENOMEM;
 
+	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
+	if (ret) {
+		dev_err(dev, "higher dma address mapping failed %d\n", ret);
+		return ret;
+	}
+
 	aud_drv_data->axi_clk = devm_clk_get(dev, "s_axi_lite_aclk");
 	if (IS_ERR(aud_drv_data->axi_clk)) {
 		ret = PTR_ERR(aud_drv_data->axi_clk);
@@ -558,8 +797,7 @@
 	}
 	ret = clk_prepare_enable(aud_drv_data->axi_clk);
 	if (ret) {
-		dev_err(dev,
-			"failed to enable s_axi_lite_aclk(%d)\n", ret);
+		dev_err(dev, "failed to enable s_axi_lite_aclk(%d)\n", ret);
 		return ret;
 	}
 
@@ -570,59 +808,17 @@
 		goto clk_err;
 	}
 
-	val = readl(aud_drv_data->mmio + XLNX_AUD_CORE_CONFIG);
+	val = ioread32(aud_drv_data->mmio + XLNX_AUD_CORE_CONFIG);
 	if (val & AUD_CFG_MM2S_MASK) {
-		aud_drv_data->mm2s_presence = true;
-		ret = xlnx_formatter_pcm_reset(aud_drv_data->mmio +
-					       XLNX_MM2S_OFFSET);
-		if (ret) {
-			dev_err(dev, "audio formatter reset failed\n");
-			goto clk_err;
-		}
-		xlnx_formatter_disable_irqs(aud_drv_data->mmio +
-					    XLNX_MM2S_OFFSET,
-					    SNDRV_PCM_STREAM_PLAYBACK);
-
-		aud_drv_data->mm2s_irq = platform_get_irq_byname(pdev,
-								 "irq_mm2s");
-		if (aud_drv_data->mm2s_irq < 0) {
-			ret = aud_drv_data->mm2s_irq;
-			goto clk_err;
-		}
-		ret = devm_request_irq(dev, aud_drv_data->mm2s_irq,
-				       xlnx_mm2s_irq_handler, 0,
-				       "xlnx_formatter_pcm_mm2s_irq", dev);
-		if (ret) {
-			dev_err(dev, "xlnx audio mm2s irq request failed\n");
+		ret = configure_mm2s(aud_drv_data, pdev);
+		if (ret)
 			goto clk_err;
-		}
 	}
+
 	if (val & AUD_CFG_S2MM_MASK) {
-		aud_drv_data->s2mm_presence = true;
-		ret = xlnx_formatter_pcm_reset(aud_drv_data->mmio +
-					       XLNX_S2MM_OFFSET);
-		if (ret) {
-			dev_err(dev, "audio formatter reset failed\n");
+		ret = configure_s2mm(aud_drv_data, pdev);
+		if (ret)
 			goto clk_err;
-		}
-		xlnx_formatter_disable_irqs(aud_drv_data->mmio +
-					    XLNX_S2MM_OFFSET,
-					    SNDRV_PCM_STREAM_CAPTURE);
-
-		aud_drv_data->s2mm_irq = platform_get_irq_byname(pdev,
-								 "irq_s2mm");
-		if (aud_drv_data->s2mm_irq < 0) {
-			ret = aud_drv_data->s2mm_irq;
-			goto clk_err;
-		}
-		ret = devm_request_irq(dev, aud_drv_data->s2mm_irq,
-				       xlnx_s2mm_irq_handler, 0,
-				       "xlnx_formatter_pcm_s2mm_irq",
-				       dev);
-		if (ret) {
-			dev_err(dev, "xlnx audio s2mm irq request failed\n");
-			goto clk_err;
-		}
 	}
 
 	dev_set_drvdata(dev, aud_drv_data);
@@ -634,6 +830,19 @@
 		goto clk_err;
 	}
 
+	pdata_size = sizeof(aud_drv_data->nodes);
+	if (aud_drv_data->nodes[XLNX_PLAYBACK] ||
+	    aud_drv_data->nodes[XLNX_CAPTURE])
+		aud_drv_data->pdev =
+			platform_device_register_resndata(dev, "xlnx_snd_card",
+							  PLATFORM_DEVID_AUTO,
+							  NULL, 0,
+							  &aud_drv_data->nodes,
+							  pdata_size);
+	if (!aud_drv_data->pdev)
+		dev_err(dev, "sound card device creation failed\n");
+
+	dev_info(dev, "pcm platform device registered\n");
 	return 0;
 
 clk_err:
@@ -646,6 +855,8 @@
 	int ret = 0;
 	struct xlnx_pcm_drv_data *adata = dev_get_drvdata(&pdev->dev);
 
+	platform_device_unregister(adata->pdev);
+
 	if (adata->s2mm_presence)
 		ret = xlnx_formatter_pcm_reset(adata->mmio + XLNX_S2MM_OFFSET);
 
@@ -676,5 +887,5 @@
 };
 
 module_platform_driver(xlnx_formatter_pcm_driver);
-MODULE_AUTHOR("Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>");
+MODULE_AUTHOR("Maruthi Srinivas Bayyavarapu");
 MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xlnx_i2s.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xlnx_i2s.c
@@ -7,6 +7,7 @@
 // Author: Praveen Vuppala <praveenv@xilinx.com>
 // Author: Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>
 
+#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -22,15 +23,22 @@
 #define I2S_CH0_OFFSET			0x30
 #define I2S_I2STIM_VALID_MASK		GENMASK(7, 0)
 
+struct xlnx_i2s_dev_data {
+	void __iomem *base;
+	struct clk *axi_clk;
+	struct clk *axis_clk;
+	struct clk *aud_mclk;
+};
+
 static int xlnx_i2s_set_sclkout_div(struct snd_soc_dai *cpu_dai,
 				    int div_id, int div)
 {
-	void __iomem *base = snd_soc_dai_get_drvdata(cpu_dai);
+	struct xlnx_i2s_dev_data *dev_data = snd_soc_dai_get_drvdata(cpu_dai);
 
 	if (!div || (div & ~I2S_I2STIM_VALID_MASK))
 		return -EINVAL;
 
-	writel(div, base + I2S_I2STIM_OFFSET);
+	writel(div, dev_data->base + I2S_I2STIM_OFFSET);
 
 	return 0;
 }
@@ -40,13 +48,13 @@
 			      struct snd_soc_dai *i2s_dai)
 {
 	u32 reg_off, chan_id;
-	void __iomem *base = snd_soc_dai_get_drvdata(i2s_dai);
+	struct xlnx_i2s_dev_data *dev_data = snd_soc_dai_get_drvdata(i2s_dai);
 
 	chan_id = params_channels(params) / 2;
 
 	while (chan_id > 0) {
 		reg_off = I2S_CH0_OFFSET + ((chan_id - 1) * 4);
-		writel(chan_id, base + reg_off);
+		writel(chan_id, dev_data->base + reg_off);
 		chan_id--;
 	}
 
@@ -56,18 +64,18 @@
 static int xlnx_i2s_trigger(struct snd_pcm_substream *substream, int cmd,
 			    struct snd_soc_dai *i2s_dai)
 {
-	void __iomem *base = snd_soc_dai_get_drvdata(i2s_dai);
+	struct xlnx_i2s_dev_data *dev_data = snd_soc_dai_get_drvdata(i2s_dai);
 
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_START:
 	case SNDRV_PCM_TRIGGER_RESUME:
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
-		writel(1, base + I2S_CORE_CTRL_OFFSET);
+		writel(1, dev_data->base + I2S_CORE_CTRL_OFFSET);
 		break;
 	case SNDRV_PCM_TRIGGER_STOP:
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
-		writel(0, base + I2S_CORE_CTRL_OFFSET);
+		writel(0, dev_data->base + I2S_CORE_CTRL_OFFSET);
 		break;
 	default:
 		return -EINVAL;
@@ -95,10 +103,10 @@
 
 static int xlnx_i2s_probe(struct platform_device *pdev)
 {
-	void __iomem *base;
 	struct snd_soc_dai_driver *dai_drv;
+	struct xlnx_i2s_dev_data *dev_data;
 	int ret;
-	u32 ch, format, data_width;
+	u32 ch = 0, format, data_width = 0;
 	struct device *dev = &pdev->dev;
 	struct device_node *node = dev->of_node;
 
@@ -106,9 +114,16 @@
 	if (!dai_drv)
 		return -ENOMEM;
 
-	base = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(base))
-		return PTR_ERR(base);
+	dev_data = devm_kzalloc(&pdev->dev, sizeof(*dev_data), GFP_KERNEL);
+	if (!dev_data)
+		return -ENOMEM;
+
+	dev_data->axi_clk = devm_clk_get(&pdev->dev, "s_axi_ctrl_aclk");
+	if (IS_ERR(dev_data->axi_clk)) {
+		ret = PTR_ERR(dev_data->axi_clk);
+		dev_err(&pdev->dev, "failed to get s_axi_ctrl_aclk(%d)\n", ret);
+		return ret;
+	}
 
 	ret = of_property_read_u32(node, "xlnx,num-channels", &ch);
 	if (ret < 0) {
@@ -141,6 +156,15 @@
 		dai_drv->playback.channels_max = ch;
 		dai_drv->playback.rates	= SNDRV_PCM_RATE_8000_192000;
 		dai_drv->ops = &xlnx_i2s_dai_ops;
+
+		dev_data->axis_clk = devm_clk_get(&pdev->dev,
+						  "s_axis_aud_aclk");
+		if (IS_ERR(dev_data->axis_clk)) {
+			ret = PTR_ERR(dev_data->axis_clk);
+			dev_err(&pdev->dev,
+				"failed to get s_axis_aud_aclk(%d)\n", ret);
+			return ret;
+		}
 	} else if (of_device_is_compatible(node, "xlnx,i2s-receiver-1.0")) {
 		dai_drv->name = "xlnx_i2s_capture";
 		dai_drv->capture.stream_name = "Capture";
@@ -149,30 +173,93 @@
 		dai_drv->capture.channels_max = ch;
 		dai_drv->capture.rates = SNDRV_PCM_RATE_8000_192000;
 		dai_drv->ops = &xlnx_i2s_dai_ops;
+
+		dev_data->axis_clk = devm_clk_get(&pdev->dev,
+						  "m_axis_aud_aclk");
+		if (IS_ERR(dev_data->axis_clk)) {
+			ret = PTR_ERR(dev_data->axis_clk);
+			dev_err(&pdev->dev,
+				"failed to get m_axis_aud_aclk(%d)\n", ret);
+			return ret;
+		}
 	} else {
 		return -ENODEV;
 	}
 
-	dev_set_drvdata(&pdev->dev, base);
+	dev_data->aud_mclk = devm_clk_get(&pdev->dev, "aud_mclk");
+	if (IS_ERR(dev_data->aud_mclk)) {
+		ret = PTR_ERR(dev_data->aud_mclk);
+		dev_err(&pdev->dev, "failed to get aud_mclk(%d)\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(dev_data->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to enable s_axi_ctrl_aclk(%d)\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(dev_data->axis_clk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to enable axis_aud_aclk(%d)\n", ret);
+		goto err_axis_clk;
+	}
+
+	ret = clk_prepare_enable(dev_data->aud_mclk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to enable aud_mclk(%d)\n", ret);
+		goto err_aud_mclk;
+	}
+
+	dev_data->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(dev_data->base)) {
+		ret = PTR_ERR(dev_data->base);
+		goto clk_err;
+	}
+
+	dev_set_drvdata(&pdev->dev, dev_data);
 
 	ret = devm_snd_soc_register_component(&pdev->dev, &xlnx_i2s_component,
 					      dai_drv, 1);
 	if (ret) {
 		dev_err(&pdev->dev, "i2s component registration failed\n");
-		return ret;
+		goto clk_err;
 	}
 
 	dev_info(&pdev->dev, "%s DAI registered\n", dai_drv->name);
 
+	return 0;
+clk_err:
+	clk_disable_unprepare(dev_data->aud_mclk);
+err_aud_mclk:
+	clk_disable_unprepare(dev_data->axis_clk);
+err_axis_clk:
+	clk_disable_unprepare(dev_data->axi_clk);
+
 	return ret;
 }
 
+static int xlnx_i2s_remove(struct platform_device *pdev)
+{
+	struct xlnx_i2s_dev_data *dev_data = dev_get_drvdata(&pdev->dev);
+
+	clk_disable_unprepare(dev_data->aud_mclk);
+	clk_disable_unprepare(dev_data->axis_clk);
+	clk_disable_unprepare(dev_data->axi_clk);
+
+	return 0;
+}
+
 static struct platform_driver xlnx_i2s_aud_driver = {
 	.driver = {
 		.name = DRV_NAME,
 		.of_match_table = xlnx_i2s_of_match,
 	},
 	.probe = xlnx_i2s_probe,
+	.remove = xlnx_i2s_remove,
 };
 
 module_platform_driver(xlnx_i2s_aud_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xlnx_pl_snd_card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xlnx_pl_snd_card.c
@@ -0,0 +1,540 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx ASoC sound card support
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/idr.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+
+#include "xlnx_snd_common.h"
+
+#define I2S_CLOCK_RATIO 384
+#define XLNX_MAX_PL_SND_DEV 6
+
+static DEFINE_IDA(xlnx_snd_card_dev);
+
+enum {
+	I2S_AUDIO = 0,
+	HDMI_AUDIO,
+	SDI_AUDIO,
+	SPDIF_AUDIO,
+	DP_AUDIO,
+	XLNX_MAX_IFACE,
+};
+
+static const char *xlnx_snd_card_name[XLNX_MAX_IFACE] = {
+	[I2S_AUDIO]	= "xlnx-i2s-snd-card",
+	[HDMI_AUDIO]	= "xlnx-hdmi-snd-card",
+	[SDI_AUDIO]	= "xlnx-sdi-snd-card",
+	[SPDIF_AUDIO]	= "xlnx-spdif-snd-card",
+	[DP_AUDIO]	= "xlnx-dp-snd-card",
+};
+
+static const char *dev_compat[][XLNX_MAX_IFACE] = {
+	[XLNX_PLAYBACK] = {
+		"xlnx,i2s-transmitter-1.0",
+		"xlnx,v-hdmi-tx-ss-3.1",
+		"xlnx,v-uhdsdi-audio-2.0",
+		"xlnx,spdif-2.0",
+		"xlnx,v-dp-txss-3.0"
+	},
+
+	[XLNX_CAPTURE] = {
+		"xlnx,i2s-receiver-1.0",
+		"xlnx,v-hdmi-rx-ss-3.1",
+		"xlnx,v-uhdsdi-audio-2.0",
+		"xlnx,spdif-2.0",
+		"xlnx,v-dp-rxss-3.0",
+	},
+};
+
+static int xlnx_spdif_card_hw_params(struct snd_pcm_substream *substream,
+				     struct snd_pcm_hw_params *params)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct pl_card_data *prv = snd_soc_card_get_drvdata(rtd->card);
+	u32 sample_rate = params_rate(params);
+
+	/* mclk must be >=1024 * sampleing rate */
+	prv->mclk_val = 1024 * sample_rate;
+	prv->mclk_ratio = 1024;
+	return clk_set_rate(prv->mclk, prv->mclk_val);
+}
+
+static int xlnx_sdi_card_hw_params(struct snd_pcm_substream *substream,
+				   struct snd_pcm_hw_params *params)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct pl_card_data *prv = snd_soc_card_get_drvdata(rtd->card);
+	u32 sample_rate = params_rate(params);
+
+	prv->mclk_val = prv->mclk_ratio * sample_rate;
+	return clk_set_rate(prv->mclk, prv->mclk_val);
+}
+
+static int xlnx_dp_card_hw_params(struct snd_pcm_substream *substream,
+				  struct snd_pcm_hw_params *params)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct pl_card_data *prv = snd_soc_card_get_drvdata(rtd->card);
+	u32 sample_rate = params_rate(params);
+
+	switch (sample_rate) {
+	case 32000:
+	case 44100:
+	case 48000:
+	case 88200:
+	case 96000:
+	case 176400:
+	case 192000:
+		prv->mclk_ratio = 512;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	prv->mclk_val = prv->mclk_ratio * sample_rate;
+	return clk_set_rate(prv->mclk, prv->mclk_val);
+}
+
+static int xlnx_hdmi_card_hw_params(struct snd_pcm_substream *substream,
+				    struct snd_pcm_hw_params *params)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct pl_card_data *prv = snd_soc_card_get_drvdata(rtd->card);
+	u32 sample_rate = params_rate(params);
+
+	switch (sample_rate) {
+	case 32000:
+	case 44100:
+	case 48000:
+	case 88200:
+	case 96000:
+	case 176400:
+	case 192000:
+		prv->mclk_ratio = 512;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	prv->mclk_val = prv->mclk_ratio * sample_rate;
+	return clk_set_rate(prv->mclk, prv->mclk_val);
+}
+
+static int xlnx_i2s_card_hw_params(struct snd_pcm_substream *substream,
+				   struct snd_pcm_hw_params *params)
+{
+	int ret, clk_div;
+	u32 ch, data_width, sample_rate;
+	struct pl_card_data *prv;
+
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
+
+	ch = params_channels(params);
+	data_width = params_width(params);
+	sample_rate = params_rate(params);
+
+	/* only 2 channels supported */
+	if (ch != 2)
+		return -EINVAL;
+
+	prv = snd_soc_card_get_drvdata(rtd->card);
+	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) {
+		switch (sample_rate) {
+		case 5512:
+		case 8000:
+		case 11025:
+		case 16000:
+		case 22050:
+		case 32000:
+		case 44100:
+		case 48000:
+		case 64000:
+		case 88200:
+		case 96000:
+			prv->mclk_ratio = 384;
+			break;
+		default:
+			return -EINVAL;
+		}
+	} else {
+		switch (sample_rate) {
+		case 32000:
+		case 44100:
+		case 48000:
+		case 88200:
+		case 96000:
+			prv->mclk_ratio = 384;
+			break;
+		case 64000:
+		case 176400:
+		case 192000:
+			prv->mclk_ratio = 192;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	prv->mclk_val = prv->mclk_ratio * sample_rate;
+	clk_div = DIV_ROUND_UP(prv->mclk_ratio, 2 * ch * data_width);
+	ret = snd_soc_dai_set_clkdiv(cpu_dai, 0, clk_div);
+	if (ret)
+		return ret;
+
+	return clk_set_rate(prv->mclk, prv->mclk_val);
+}
+
+static const struct snd_soc_ops xlnx_sdi_card_ops = {
+	.hw_params = xlnx_sdi_card_hw_params,
+};
+
+static const struct snd_soc_ops xlnx_i2s_card_ops = {
+	.hw_params = xlnx_i2s_card_hw_params,
+};
+
+static const struct snd_soc_ops xlnx_hdmi_card_ops = {
+	.hw_params = xlnx_hdmi_card_hw_params,
+};
+
+static const struct snd_soc_ops xlnx_dp_card_ops = {
+	.hw_params = xlnx_dp_card_hw_params,
+};
+
+static const struct snd_soc_ops xlnx_spdif_card_ops = {
+	.hw_params = xlnx_spdif_card_hw_params,
+};
+
+SND_SOC_DAILINK_DEFS(xlnx_i2s_capture,
+		     DAILINK_COMP_ARRAY(COMP_CPU("xlnx_i2s_capture")),
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_i2s_playback,
+		     DAILINK_COMP_ARRAY(COMP_CPU("xlnx_i2s_playback")),
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_hdmi_tx,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xlnx_hdmi_tx")),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_hdmi_rx,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xlnx_hdmi_rx")),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_dp_tx,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xlnx_dp_tx")),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_dp_rx,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xlnx_dp_rx")),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_sdi_tx,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xlnx_sdi_tx")),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_sdi_rx,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "xlnx_sdi_rx")),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+SND_SOC_DAILINK_DEFS(xlnx_spdif,
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_DUMMY()),
+		     DAILINK_COMP_ARRAY(COMP_PLATFORM(NULL)));
+
+static struct snd_soc_dai_link xlnx_snd_dai[][XLNX_MAX_PATHS] = {
+	[I2S_AUDIO] = {
+		{
+			.name = "xilinx-i2s_playback",
+			SND_SOC_DAILINK_REG(xlnx_i2s_playback),
+			.ops = &xlnx_i2s_card_ops,
+		},
+		{
+			.name = "xilinx-i2s_capture",
+			SND_SOC_DAILINK_REG(xlnx_i2s_capture),
+			.ops = &xlnx_i2s_card_ops,
+		},
+	},
+	[HDMI_AUDIO] = {
+		{
+			.name = "xilinx-hdmi-playback",
+			SND_SOC_DAILINK_REG(xlnx_hdmi_tx),
+			.ops = &xlnx_hdmi_card_ops,
+			.dai_fmt = SND_SOC_DAIFMT_I2S |
+				   SND_SOC_DAIFMT_NB_NF |
+				   SND_SOC_DAIFMT_CBS_CFS,
+		},
+		{
+			.name = "xilinx-hdmi-capture",
+			SND_SOC_DAILINK_REG(xlnx_hdmi_rx),
+		},
+	},
+	[SDI_AUDIO] = {
+		{
+			.name = "xlnx-sdi-playback",
+			SND_SOC_DAILINK_REG(xlnx_sdi_tx),
+			.ops = &xlnx_sdi_card_ops,
+		},
+		{
+			.name = "xlnx-sdi-capture",
+			SND_SOC_DAILINK_REG(xlnx_sdi_rx),
+		},
+	},
+	[SPDIF_AUDIO] = {
+		{
+			.name = "xilinx-spdif_playback",
+			SND_SOC_DAILINK_REG(xlnx_spdif),
+			.ops = &xlnx_spdif_card_ops,
+		},
+		{
+			.name = "xilinx-spdif_capture",
+			SND_SOC_DAILINK_REG(xlnx_spdif),
+			.ops = &xlnx_spdif_card_ops,
+		},
+	},
+	[DP_AUDIO] = {
+		{
+			.name = "xilinx-dp-playback",
+			SND_SOC_DAILINK_REG(xlnx_dp_tx),
+			.ops = &xlnx_dp_card_ops,
+			.dai_fmt = SND_SOC_DAIFMT_I2S |
+				   SND_SOC_DAIFMT_NB_NF |
+				   SND_SOC_DAIFMT_CBS_CFS,
+		},
+		{
+			.name = "xilinx-dp-capture",
+			SND_SOC_DAILINK_REG(xlnx_dp_rx),
+		},
+	},
+};
+
+static int find_link(struct device_node *node, int direction)
+{
+	int ret;
+	u32 i, size;
+	const char **link_names = dev_compat[direction];
+
+	size = ARRAY_SIZE(dev_compat[direction]);
+
+	for (i = 0; i < size; i++) {
+		ret = of_device_is_compatible(node, link_names[i]);
+		if (ret)
+			return i;
+	}
+	return -ENODEV;
+}
+
+static int xlnx_snd_probe(struct platform_device *pdev)
+{
+	u32 i, max_links = 0, start_count = 0;
+	size_t sz;
+	char *buf;
+	int ret, audio_interface;
+	struct snd_soc_dai_link *dai;
+	struct pl_card_data *prv;
+	struct platform_device *iface_pdev;
+
+	struct snd_soc_card *card;
+	struct device_node **node = pdev->dev.platform_data;
+
+	if (!node)
+		return -ENODEV;
+
+	if (node[XLNX_PLAYBACK] && node[XLNX_CAPTURE]) {
+		max_links = 2;
+		start_count = XLNX_PLAYBACK;
+	} else if (node[XLNX_PLAYBACK]) {
+		max_links = 1;
+		start_count = XLNX_PLAYBACK;
+	} else if (node[XLNX_CAPTURE]) {
+		max_links = 1;
+		start_count = XLNX_CAPTURE;
+	}
+
+	card = devm_kzalloc(&pdev->dev, sizeof(struct snd_soc_card),
+			    GFP_KERNEL);
+	if (!card)
+		return -ENOMEM;
+
+	card->dev = &pdev->dev;
+
+	card->dai_link = devm_kzalloc(card->dev,
+				      sizeof(*dai) * max_links,
+				      GFP_KERNEL);
+	if (!card->dai_link)
+		return -ENOMEM;
+
+	prv = devm_kzalloc(card->dev,
+			   sizeof(struct pl_card_data),
+			   GFP_KERNEL);
+	if (!prv)
+		return -ENOMEM;
+
+	card->num_links = 0;
+	for (i = start_count; i < (start_count + max_links); i++) {
+		struct device_node *pnode = of_parse_phandle(node[i],
+							     "xlnx,snd-pcm", 0);
+		if (!pnode) {
+			dev_err(card->dev, "platform node not found\n");
+			of_node_put(pnode);
+			return -ENODEV;
+		}
+
+		/*
+		 * Check for either playback or capture is enough, as
+		 * same clock is used for both.
+		 */
+		if (i == XLNX_PLAYBACK) {
+			iface_pdev = of_find_device_by_node(pnode);
+			if (!iface_pdev) {
+				of_node_put(pnode);
+				return -ENODEV;
+			}
+
+			prv->mclk = devm_clk_get(&iface_pdev->dev, "aud_mclk");
+			if (IS_ERR(prv->mclk))
+				return PTR_ERR(prv->mclk);
+		}
+		of_node_put(pnode);
+
+		if (max_links == 2)
+			dai = &card->dai_link[i];
+		else
+			dai = &card->dai_link[0];
+
+		audio_interface = find_link(node[i], i);
+		switch (audio_interface) {
+		case I2S_AUDIO:
+			*dai = xlnx_snd_dai[I2S_AUDIO][i];
+			dai->platforms->of_node = pnode;
+			dai->cpus->of_node = node[i];
+			card->num_links++;
+			snd_soc_card_set_drvdata(card, prv);
+			dev_dbg(card->dev, "%s registered\n",
+				card->dai_link[i].name);
+			break;
+		case HDMI_AUDIO:
+			*dai = xlnx_snd_dai[HDMI_AUDIO][i];
+			dai->platforms->of_node = pnode;
+			dai->codecs->of_node = node[i];
+			card->num_links++;
+			/* TODO: support multiple sampling rates */
+			prv->mclk_ratio = 384;
+			snd_soc_card_set_drvdata(card, prv);
+			dev_dbg(card->dev, "%s registered\n",
+				card->dai_link[i].name);
+			break;
+		case SDI_AUDIO:
+			*dai = xlnx_snd_dai[SDI_AUDIO][i];
+			dai->platforms->of_node = pnode;
+			dai->codecs->of_node = node[i];
+			card->num_links++;
+			/* TODO: support multiple sampling rates */
+			prv->mclk_ratio = 384;
+			snd_soc_card_set_drvdata(card, prv);
+			dev_dbg(card->dev, "%s registered\n",
+				card->dai_link[i].name);
+			break;
+		case SPDIF_AUDIO:
+			*dai = xlnx_snd_dai[SPDIF_AUDIO][i];
+			dai->platforms->of_node = pnode;
+			dai->codecs->of_node = node[i];
+			card->num_links++;
+			prv->mclk_ratio = 384;
+			snd_soc_card_set_drvdata(card, prv);
+			dev_dbg(card->dev, "%s registered\n",
+				card->dai_link[i].name);
+			break;
+		case DP_AUDIO:
+			*dai = xlnx_snd_dai[DP_AUDIO][i];
+			dai->platforms->of_node = pnode;
+			dai->codecs->of_node = node[i];
+			card->num_links++;
+			/* TODO: support multiple sampling rates */
+			prv->mclk_ratio = 512;
+			snd_soc_card_set_drvdata(card, prv);
+			dev_dbg(card->dev, "%s registered\n",
+				card->dai_link[i].name);
+			break;
+		default:
+			dev_err(card->dev, "Invalid audio interface\n");
+			return -ENODEV;
+		}
+	}
+
+	if (card->num_links) {
+		/*
+		 *  Example : i2s card name = xlnx-i2s-snd-card-0
+		 *  length = number of chars in "xlnx-i2s-snd-card"
+		 *	    + 1 ('-'), + 1 (card instance num)
+		 *	    + 1 ('\0')
+		 */
+		sz = strlen(xlnx_snd_card_name[audio_interface]) + 3;
+		buf = devm_kzalloc(card->dev, sz, GFP_KERNEL);
+		if (!buf)
+			return -ENOMEM;
+
+		prv->xlnx_snd_dev_id = ida_simple_get(&xlnx_snd_card_dev, 0,
+						      XLNX_MAX_PL_SND_DEV,
+						      GFP_KERNEL);
+		if (prv->xlnx_snd_dev_id < 0)
+			return prv->xlnx_snd_dev_id;
+
+		snprintf(buf, sz, "%s-%d", xlnx_snd_card_name[audio_interface],
+			 prv->xlnx_snd_dev_id);
+		card->name = buf;
+
+		ret = devm_snd_soc_register_card(card->dev, card);
+		if (ret) {
+			dev_err(card->dev, "%s registration failed\n",
+				card->name);
+			ida_simple_remove(&xlnx_snd_card_dev,
+					  prv->xlnx_snd_dev_id);
+			return ret;
+		}
+
+		dev_set_drvdata(card->dev, prv);
+		dev_info(card->dev, "%s registered\n", card->name);
+	}
+
+	return 0;
+}
+
+static int xlnx_snd_remove(struct platform_device *pdev)
+{
+	struct pl_card_data *pdata = dev_get_drvdata(&pdev->dev);
+
+	ida_simple_remove(&xlnx_snd_card_dev, pdata->xlnx_snd_dev_id);
+	return 0;
+}
+
+static struct platform_driver xlnx_snd_driver = {
+	.driver = {
+		.name = "xlnx_snd_card",
+	},
+	.probe = xlnx_snd_probe,
+	.remove = xlnx_snd_remove,
+};
+
+module_platform_driver(xlnx_snd_driver);
+
+MODULE_DESCRIPTION("Xilinx FPGA sound card driver");
+MODULE_AUTHOR("Maruthi Srinivas Bayyavarapu");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xlnx_sdi_audio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xlnx_sdi_audio.c
@@ -0,0 +1,609 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx SDI embed and extract audio support
+ *
+ * Copyright (c) 2018 Xilinx Pvt., Ltd
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/wait.h>
+#include <drm/drm_modes.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+
+#define DRIVER_NAME "xlnx-sdi-audio"
+
+#define XSDIAUD_CNTRL_REG_OFFSET		0x00
+#define XSDIAUD_SOFT_RST_REG_OFFSET		0x04
+#define XSDIAUD_VER_REG_OFFSET			0x08
+#define XSDIAUD_INT_EN_REG_OFFSET		0x0C
+#define XSDIAUD_INT_STS_REG_OFFSET		0x10
+#define XSDIAUD_EMB_VID_CNTRL_REG_OFFSET	0X14
+#define XSDIAUD_AUD_CNTRL_REG_OFFSET		0x18
+#define XSDIAUD_CH_VALID_REG_OFFSET		0x20
+#define XSDIAUD_CH_MUTE_REG_OFFSET		0x30
+#define XSDIAUD_ACTIVE_GRP_REG_OFFSET		0X40
+#define XSDIAUD_EXT_CH_STAT0_REG_OFFSET		0X48
+#define XSDIAUD_EXT_SRATE_STS_REG_OFFSET	0X70
+#define XSDIAUD_GUI_PARAM_REG_OFFSET		0XFC
+
+#define XSDIAUD_CNTRL_EN_MASK		BIT(0)
+#define XSDIAUD_SOFT_RST_CONFIG_MASK	BIT(0)
+#define XSDIAUD_SOFT_RST_CORE_MASK	BIT(1)
+#define XSDIAUD_VER_MAJOR_MASK		GENMASK(31, 24)
+#define XSDIAUD_VER_MINOR_MASK		GENMASK(23, 16)
+
+#define XSDIAUD_EXT_GROUP_1_STS_MASK	BIT(0)
+#define XSDIAUD_EXT_AUDSTS_UPDATE_MASK	BIT(8)
+#define XSDIAUD_EMB_VID_CNT_ELE_SHIFT	(16)
+#define XSDIAUD_EMB_VID_CNT_ELE_MASK	BIT(16)
+#define XSDIAUD_EMB_VID_CNT_TSCAN_MASK	BIT(8)
+#define XSDIAUD_EMB_VID_CNT_TSCAN_SHIFT	(8)
+#define XSDIAUD_EMB_VID_CNT_TRATE_SHIFT	(4)
+#define XSDIAUD_EMB_AUD_CNT_SS_MASK	BIT(3)
+#define XSDIAUD_EMB_AUD_CNT_ASYNC_AUDIO	BIT(4)
+
+#define CH_STATUS_UPDATE_TIMEOUT	40
+
+enum IP_MODE {
+	EMBED,
+	EXTRACT,
+};
+
+enum channel_id {
+	CHAN_ID_0 = 1,
+	CHAN_ID_1,
+};
+
+enum sdi_transport_family {
+	SDI_TRANSPORT_FAMILY_1920,
+	SDI_TRANSPORT_FAMILY_1280,
+	SDI_TRANSPORT_FAMILY_2048,
+	SDI_TRANSPORT_FAMILY_NTSC = 8,
+	SDI_TRANSPORT_FAMILY_PAL = 9,
+};
+
+/**
+ * enum sdi_audio_samplerate - audio sampling rate
+ * @XSDIAUD_SAMPRATE0:	48 KHz
+ * @XSDIAUD_SAMPRATE1:	44.1 KHz
+ * @XSDIAUD_SAMPRATE2:	32 KHz
+ */
+enum sdi_audio_samplerate {
+	XSDIAUD_SAMPRATE0,
+	XSDIAUD_SAMPRATE1,
+	XSDIAUD_SAMPRATE2
+};
+
+/**
+ * enum sdi_audio_samplesize - bits per sample
+ * @XSDIAUD_SAMPSIZE0:	20 Bit Audio Sample
+ * @XSDIAUD_SAMPSIZE1:	24 Bit Audio Sample
+ */
+enum sdi_audio_samplesize {
+	XSDIAUD_SAMPSIZE0,
+	XSDIAUD_SAMPSIZE1
+};
+
+struct dev_ctx {
+	enum IP_MODE mode;
+	void __iomem *base;
+	struct device *dev;
+	struct drm_display_mode *video_mode;
+	struct snd_pcm_substream *stream;
+	struct clk *axi_clk;
+	struct clk *axis_clk;
+	struct clk *aud_clk;
+	bool rx_srate_updated;
+	wait_queue_head_t srate_q;
+};
+
+static irqreturn_t xtract_irq_handler(int irq, void *dev_id)
+{
+	u32 irq_sts, irq_en, active_grps;
+	struct dev_ctx *ctx = dev_id;
+
+	irq_sts = ioread32(ctx->base + XSDIAUD_INT_STS_REG_OFFSET);
+	active_grps = ioread32(ctx->base + XSDIAUD_ACTIVE_GRP_REG_OFFSET);
+	if ((irq_sts & XSDIAUD_EXT_AUDSTS_UPDATE_MASK) &&
+	    (active_grps & XSDIAUD_EXT_GROUP_1_STS_MASK)) {
+		writel(XSDIAUD_EXT_AUDSTS_UPDATE_MASK,
+		       ctx->base + XSDIAUD_INT_STS_REG_OFFSET);
+		irq_en = ioread32(ctx->base + XSDIAUD_INT_EN_REG_OFFSET);
+		/* Disable further interrupts. sample rate status got updated*/
+		writel(irq_en & ~XSDIAUD_EXT_AUDSTS_UPDATE_MASK,
+		       ctx->base + XSDIAUD_INT_EN_REG_OFFSET);
+
+		ctx->rx_srate_updated = true;
+		wake_up_interruptible(&ctx->srate_q);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static void audio_enable(void __iomem *aud_base)
+{
+	u32 val;
+
+	val = ioread32(aud_base + XSDIAUD_CNTRL_REG_OFFSET);
+	val |= XSDIAUD_CNTRL_EN_MASK;
+	writel(val, aud_base + XSDIAUD_CNTRL_REG_OFFSET);
+}
+
+static void audio_disable(void __iomem *aud_base)
+{
+	u32 val;
+
+	val = ioread32(aud_base + XSDIAUD_CNTRL_REG_OFFSET);
+	val &= ~XSDIAUD_CNTRL_EN_MASK;
+	writel(val, aud_base + XSDIAUD_CNTRL_REG_OFFSET);
+}
+
+static void audio_reset_core(void __iomem *aud_base, bool reset)
+{
+	u32 val;
+
+	if (reset) {
+		/* reset the core */
+		val = ioread32(aud_base + XSDIAUD_SOFT_RST_REG_OFFSET);
+		val |= XSDIAUD_SOFT_RST_CORE_MASK;
+		writel(val, aud_base + XSDIAUD_SOFT_RST_REG_OFFSET);
+	} else {
+		/* bring the core out of reset */
+		val = ioread32(aud_base + XSDIAUD_SOFT_RST_REG_OFFSET);
+		val &= ~XSDIAUD_SOFT_RST_CORE_MASK;
+		writel(val, aud_base + XSDIAUD_SOFT_RST_REG_OFFSET);
+	}
+}
+
+static int xlnx_sdi_rx_pcm_startup(struct snd_pcm_substream *substream,
+				   struct snd_soc_dai *dai)
+{
+	int err;
+	u32 val, sample_rate;
+
+	struct dev_ctx *ctx = dev_get_drvdata(dai->dev);
+	void __iomem *base = ctx->base;
+	unsigned long jiffies = msecs_to_jiffies(CH_STATUS_UPDATE_TIMEOUT);
+
+	audio_enable(base);
+	writel(XSDIAUD_EXT_AUDSTS_UPDATE_MASK,
+	       ctx->base + XSDIAUD_INT_EN_REG_OFFSET);
+	err = wait_event_interruptible_timeout(ctx->srate_q,
+					       ctx->rx_srate_updated,
+					       jiffies);
+
+	if (!err) {
+		dev_err(ctx->dev, "Didn't get valid audio property update\n");
+		return -EINVAL;
+	}
+	ctx->rx_srate_updated = false;
+
+	val = ioread32(base + XSDIAUD_EXT_SRATE_STS_REG_OFFSET);
+	/* As both channels contain same sample rate, read either of them */
+	switch (val & CHAN_ID_1) {
+	case 0:
+		sample_rate = 48000;
+		break;
+	case 1:
+		sample_rate = 44100;
+		break;
+	case 2:
+		sample_rate = 32000;
+		break;
+	}
+
+	dev_dbg(ctx->dev,
+		"sdi rx audio enabled : sample rate = %d\n", sample_rate);
+	return 0;
+}
+
+static void xlnx_sdi_rx_pcm_shutdown(struct snd_pcm_substream *substream,
+				     struct snd_soc_dai *dai)
+{
+	struct dev_ctx *ctx = dev_get_drvdata(dai->dev);
+
+	audio_disable(ctx->base);
+
+	dev_info(dai->dev, " sdi rx audio disabled\n");
+}
+
+static int xlnx_sdi_tx_pcm_startup(struct snd_pcm_substream *substream,
+				   struct snd_soc_dai *dai)
+{
+	struct dev_ctx *ctx = dev_get_drvdata(dai->dev);
+
+	audio_enable(ctx->base);
+	ctx->stream = substream;
+
+	dev_info(ctx->dev, " sdi tx audio enabled\n");
+	return 0;
+}
+
+static int xlnx_sdi_tx_hw_params(struct snd_pcm_substream *substream,
+				 struct snd_pcm_hw_params *params,
+				 struct snd_soc_dai *dai)
+{
+	u32 val = 0;
+	u32 num_channels, sample_rate, sig_bits;
+
+	struct dev_ctx *ctx = dev_get_drvdata(dai->dev);
+	void __iomem *base = ctx->base;
+
+	/* video mode properties needed by audio driver are shared to audio
+	 * driver through a pointer in platform data. This is used here in
+	 * audio driver. The solution may be needed to modify/extend to avoid
+	 * probable error scenarios
+	 */
+	if (!ctx->video_mode || !ctx->video_mode->vdisplay ||
+	    !drm_mode_vrefresh(ctx->video_mode)) {
+		dev_err(ctx->dev, "couldn't find video display properties\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * map video properties.
+	 * Note: 1920x1080 and 2048x1080 are the resolutions of sub images for
+	 * 3840x2160 and 4096x2160 resolutions respectively.
+	 */
+	switch (ctx->video_mode->hdisplay) {
+	case 1920:
+	case 3840:
+		val = SDI_TRANSPORT_FAMILY_1920;
+		break;
+	case 1280:
+		val |= SDI_TRANSPORT_FAMILY_1280;
+		break;
+	case 2048:
+	case 4096:
+		val |= SDI_TRANSPORT_FAMILY_2048;
+		break;
+	case 720:
+		if (ctx->video_mode->vdisplay == 486)
+			val |= SDI_TRANSPORT_FAMILY_NTSC;
+		else if (ctx->video_mode->vdisplay == 576)
+			val |= SDI_TRANSPORT_FAMILY_PAL;
+		else
+			return -EINVAL;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (drm_mode_vrefresh(ctx->video_mode)) {
+	case 24:
+		val |= (3 << XSDIAUD_EMB_VID_CNT_TRATE_SHIFT);
+		break;
+	case 25:
+		val |= (5 << XSDIAUD_EMB_VID_CNT_TRATE_SHIFT);
+		break;
+	case 30:
+		val |= (7 << XSDIAUD_EMB_VID_CNT_TRATE_SHIFT);
+		break;
+	case 48:
+		val |= (8 << XSDIAUD_EMB_VID_CNT_TRATE_SHIFT);
+		break;
+	case 50:
+		val |= (9 << XSDIAUD_EMB_VID_CNT_TRATE_SHIFT);
+		break;
+	case 60:
+		val |= (11 << XSDIAUD_EMB_VID_CNT_TRATE_SHIFT);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (!(ctx->video_mode->flags & DRM_MODE_FLAG_INTERLACE))
+		val |= XSDIAUD_EMB_VID_CNT_TSCAN_MASK;
+
+	val |= XSDIAUD_EMB_VID_CNT_ELE_MASK;
+
+	writel(val, base + XSDIAUD_EMB_VID_CNTRL_REG_OFFSET);
+
+	/* map audio properties */
+	num_channels = params_channels(params);
+	sample_rate = params_rate(params);
+	sig_bits = snd_pcm_format_width(params_format(params));
+
+	dev_info(ctx->dev,
+		 "stream params: channels = %d sample_rate = %d bits = %d\n",
+		 num_channels, sample_rate, sig_bits);
+
+	val = 0;
+	val |= XSDIAUD_EMB_AUD_CNT_ASYNC_AUDIO;
+
+	switch (sample_rate) {
+	case 48000:
+		val |= XSDIAUD_SAMPRATE0;
+		break;
+	case 44100:
+		val |= XSDIAUD_SAMPRATE1;
+		break;
+	case 32000:
+		val |= XSDIAUD_SAMPRATE2;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (sig_bits == 24)
+		val |= XSDIAUD_EMB_AUD_CNT_SS_MASK;
+
+	writel(val, base + XSDIAUD_AUD_CNTRL_REG_OFFSET);
+
+	writel(BIT(num_channels) - 1, base + XSDIAUD_CH_VALID_REG_OFFSET);
+
+	return 0;
+}
+
+static void xlnx_sdi_tx_pcm_shutdown(struct snd_pcm_substream *substream,
+				     struct snd_soc_dai *dai)
+{
+	struct dev_ctx *ctx = dev_get_drvdata(dai->dev);
+	void __iomem *base = ctx->base;
+
+	audio_disable(base);
+	ctx->stream = NULL;
+
+	dev_info(ctx->dev, " sdi tx audio disabled\n");
+}
+
+static const struct snd_soc_component_driver xlnx_sdi_component = {
+	.name = "xlnx-sdi-dai-component",
+};
+
+static const struct snd_soc_dai_ops xlnx_sdi_rx_dai_ops = {
+	.startup = xlnx_sdi_rx_pcm_startup,
+	.shutdown = xlnx_sdi_rx_pcm_shutdown,
+};
+
+static struct snd_soc_dai_driver xlnx_sdi_rx_dai = {
+	.name = "xlnx_sdi_rx",
+	.capture = {
+		.stream_name = "Capture",
+		.channels_min = 2,
+		.channels_max = 8,
+		.rates = SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 |
+			SNDRV_PCM_RATE_48000,
+		.formats = SNDRV_PCM_FMTBIT_S24_LE,
+	},
+	.ops = &xlnx_sdi_rx_dai_ops,
+};
+
+static const struct snd_soc_dai_ops xlnx_sdi_tx_dai_ops = {
+	.startup =	xlnx_sdi_tx_pcm_startup,
+	.hw_params =	xlnx_sdi_tx_hw_params,
+	.shutdown =	xlnx_sdi_tx_pcm_shutdown,
+};
+
+static struct snd_soc_dai_driver xlnx_sdi_tx_dai = {
+	.name = "xlnx_sdi_tx",
+	.playback = {
+		.stream_name = "Playback",
+		.channels_min = 2,
+		.channels_max = 8,
+		.rates = SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 |
+			SNDRV_PCM_RATE_48000,
+		.formats = SNDRV_PCM_FMTBIT_S24_LE,
+	},
+	.ops = &xlnx_sdi_tx_dai_ops,
+};
+
+static int xlnx_sdi_audio_probe(struct platform_device *pdev)
+{
+	u32 val;
+	int ret;
+	struct dev_ctx *ctx;
+	struct resource *res;
+	struct device *video_dev;
+	struct device_node *video_node;
+	struct platform_device *video_pdev;
+	struct snd_soc_dai_driver *snd_dai;
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+
+	/* TODO - remove before upstreaming */
+	if (of_device_is_compatible(node, "xlnx,v-uhdsdi-audio-1.0")) {
+		dev_err(&pdev->dev, "driver doesn't support sdi audio v1.0\n");
+		return -ENODEV;
+	}
+
+	ctx = devm_kzalloc(&pdev->dev, sizeof(struct dev_ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENODEV;
+
+	ctx->axi_clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+	if (IS_ERR(ctx->axi_clk)) {
+		ret = PTR_ERR(ctx->axi_clk);
+		dev_err(&pdev->dev, "failed to get s_axi_aclk(%d)\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(ctx->axi_clk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to enable s_axi_aclk(%d)\n", ret);
+		return ret;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "No IO MEM resource found\n");
+		ret = -ENODEV;
+		goto err_axis;
+	}
+
+	ctx->base = devm_ioremap_resource(&pdev->dev, res);
+	if (!ctx->base) {
+		dev_err(&pdev->dev, "ioremap failed\n");
+		ret = -EADDRNOTAVAIL;
+		goto err_axis;
+	}
+
+	ctx->dev = &pdev->dev;
+
+	val = ioread32(ctx->base + XSDIAUD_GUI_PARAM_REG_OFFSET);
+	if (val & BIT(6)) {
+		ctx->mode = EXTRACT;
+
+		ctx->axis_clk = devm_clk_get(&pdev->dev, "m_axis_clk");
+		if (IS_ERR(ctx->axis_clk)) {
+			ret = PTR_ERR(ctx->axis_clk);
+			dev_err(&pdev->dev, "failed to get m_axis_clk(%d)\n",
+				ret);
+			goto err_axis;
+		}
+
+		ctx->aud_clk = devm_clk_get(&pdev->dev, "sdi_extract_clk");
+		if (IS_ERR(ctx->aud_clk)) {
+			ret = PTR_ERR(ctx->aud_clk);
+			dev_err(&pdev->dev, "failed to get sdi_extract_clk(%d)\n",
+				ret);
+			goto err_axis;
+		}
+
+		res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+		if (!res) {
+			dev_err(&pdev->dev, "No IRQ resource found\n");
+			ret = -ENODEV;
+			goto err_axis;
+		}
+		ret = devm_request_irq(&pdev->dev, res->start,
+				       xtract_irq_handler,
+				       0, "XLNX_SDI_AUDIO_XTRACT", ctx);
+		if (ret) {
+			dev_err(&pdev->dev, "extract irq request failed\n");
+			ret = -ENODEV;
+			goto err_axis;
+		}
+
+		init_waitqueue_head(&ctx->srate_q);
+
+		snd_dai = &xlnx_sdi_rx_dai;
+	} else {
+		ctx->mode = EMBED;
+		ctx->axis_clk = devm_clk_get(&pdev->dev, "s_axis_clk");
+		if (IS_ERR(ctx->axis_clk)) {
+			ret = PTR_ERR(ctx->axis_clk);
+			dev_err(&pdev->dev, "failed to get s_axis_clk(%d)\n",
+				ret);
+			goto err_axis;
+		}
+
+		ctx->aud_clk = devm_clk_get(&pdev->dev, "sdi_embed_clk");
+		if (IS_ERR(ctx->aud_clk)) {
+			ret = PTR_ERR(ctx->aud_clk);
+			dev_err(&pdev->dev, "failed to get aud_clk(%d)\n",
+				ret);
+			goto err_axis;
+		}
+
+		video_node = of_graph_get_remote_node(pdev->dev.of_node, 0, 0);
+		if (!video_node) {
+			dev_err(ctx->dev, "video_node not found\n");
+			of_node_put(video_node);
+			ret = -ENODEV;
+			goto err_axis;
+		}
+
+		video_pdev = of_find_device_by_node(video_node);
+		if (!video_pdev) {
+			of_node_put(video_node);
+			ret = -ENODEV;
+			goto err_axis;
+		}
+
+		video_dev = &video_pdev->dev;
+		ctx->video_mode =
+			(struct drm_display_mode *)video_dev->platform_data;
+		/* invalid 'platform_data' implies video driver is not loaded */
+		if (!ctx->video_mode) {
+			of_node_put(video_node);
+			ret = -EPROBE_DEFER;
+			goto err_axis;
+		}
+
+		snd_dai = &xlnx_sdi_tx_dai;
+		of_node_put(video_node);
+	}
+
+	ret = clk_prepare_enable(ctx->axis_clk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to enable s_axis_clk(%d)\n", ret);
+		goto err_axis;
+	}
+
+	ret = clk_prepare_enable(ctx->aud_clk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to enable sdi_extract_clk(%d)\n", ret);
+		goto err_aud_clk;
+	}
+
+	ret = devm_snd_soc_register_component(&pdev->dev, &xlnx_sdi_component,
+					      snd_dai, 1);
+	if (ret) {
+		dev_err(&pdev->dev, "couldn't register codec DAI\n");
+		goto err_clk;
+	}
+
+	dev_set_drvdata(&pdev->dev, ctx);
+
+	audio_reset_core(ctx->base, true);
+	audio_reset_core(ctx->base, false);
+
+	dev_info(&pdev->dev, "xlnx sdi codec dai component registered\n");
+	return 0;
+
+err_clk:
+	clk_disable_unprepare(ctx->aud_clk);
+err_aud_clk:
+	clk_disable_unprepare(ctx->axis_clk);
+err_axis:
+	clk_disable_unprepare(ctx->axi_clk);
+	return ret;
+}
+
+static int xlnx_sdi_audio_remove(struct platform_device *pdev)
+{
+	struct dev_ctx *ctx = dev_get_drvdata(&pdev->dev);
+
+	audio_disable(ctx->base);
+	audio_reset_core(ctx->base, true);
+
+	clk_disable_unprepare(ctx->aud_clk);
+	clk_disable_unprepare(ctx->axis_clk);
+	clk_disable_unprepare(ctx->axi_clk);
+	return 0;
+}
+
+static const struct of_device_id xlnx_sdi_audio_of_match[] = {
+	{ .compatible = "xlnx,v-uhdsdi-audio-1.0"},
+	{ .compatible = "xlnx,v-uhdsdi-audio-2.0"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xlnx_sdi_audio_of_match);
+
+static struct platform_driver xlnx_sdi_audio_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = xlnx_sdi_audio_of_match,
+	},
+	.probe = xlnx_sdi_audio_probe,
+	.remove = xlnx_sdi_audio_remove,
+};
+
+module_platform_driver(xlnx_sdi_audio_driver);
+
+MODULE_DESCRIPTION("xilinx sdi audio codec driver");
+MODULE_AUTHOR("Maruthi Srinivas Bayyavarapu");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xlnx_snd_common.h
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xlnx_snd_common.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx ASoC sound card support
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ */
+
+#ifndef _XLNX_SND_COMMON_H
+#define _XLNX_SND_COMMON_H
+
+enum {
+	XLNX_PLAYBACK = 0,
+	XLNX_CAPTURE = 1,
+	XLNX_MAX_PATHS = 2
+};
+
+struct pl_card_data {
+	u32 mclk_val;
+	u32 mclk_ratio;
+	int xlnx_snd_dev_id;
+	struct clk *mclk;
+};
+#endif /* _XLNX_SND_COMMON_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/soc/xilinx/xlnx_spdif.c
+++ linux-xilinx-zynqmp-5.15.0/sound/soc/xilinx/xlnx_spdif.c
@@ -24,32 +24,43 @@
 #define XLNX_SPDIF_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE)
 
 #define XSPDIF_IRQ_STS_REG		0x20
+#define XSPDIF_IRQ_STS_CH_STS_MASK	BIT(5)
 #define XSPDIF_IRQ_ENABLE_REG		0x28
 #define XSPDIF_SOFT_RESET_REG		0x40
+#define XSPDIF_SOFT_RESET_VAL		0xA
 #define XSPDIF_CONTROL_REG		0x44
+#define XSPDIF_CONTROL_ENABLE_MASK	BIT(0)
+#define XSPDIF_CONTROL_FIFO_FLUSH_MASK	BIT(1)
+#define XSPDIF_CONTROL_CLK_CFG_MASK	GENMASK(5, 2)
+#define XSPDIF_CONTROL_CLK_CFG_SHIFT	2
 #define XSPDIF_CHAN_0_STS_REG		0x4C
-#define XSPDIF_GLOBAL_IRQ_ENABLE_REG	0x1C
+#define XSPDIF_GLOBAL_IRQ_REG		0x1C
+#define XSPDIF_GLOBAL_IRQ_ENABLE_MASK	BIT(31)
 #define XSPDIF_CH_A_USER_DATA_REG_0	0x64
 
-#define XSPDIF_CORE_ENABLE_MASK		BIT(0)
-#define XSPDIF_FIFO_FLUSH_MASK		BIT(1)
-#define XSPDIF_CH_STS_MASK		BIT(5)
-#define XSPDIF_GLOBAL_IRQ_ENABLE	BIT(31)
-#define XSPDIF_CLOCK_CONFIG_BITS_MASK	GENMASK(5, 2)
-#define XSPDIF_CLOCK_CONFIG_BITS_SHIFT	2
-#define XSPDIF_SOFT_RESET_VALUE		0xA
-
-#define MAX_CHANNELS			2
-#define AES_SAMPLE_WIDTH		32
-#define CH_STATUS_UPDATE_TIMEOUT	40
+#define XSPDIF_MAX_CHANNELS		2
+#define XSPDIF_AES_SAMPLE_WIDTH		32
+#define XSPDIF_CH_STS_UPDATE_TIMEOUT	40
+
+enum {
+	CLK_DIV_BY_4,
+	CLK_DIV_BY_8,
+	CLK_DIV_BY_16,
+	CLK_DIV_BY_24,
+	CLK_DIV_BY_32,
+	CLK_DIV_BY_48,
+	CLK_DIV_BY_64,
+};
 
 struct spdif_dev_data {
-	u32 mode;
-	u32 aclk;
-	bool rx_chsts_updated;
+	wait_queue_head_t chsts_q;
 	void __iomem *base;
 	struct clk *axi_clk;
-	wait_queue_head_t chsts_q;
+	struct clk *axis_clk;
+	struct clk *aud_clk;
+	u32 mode;
+	unsigned long aclk;
+	bool rx_chsts_updated;
 };
 
 static irqreturn_t xlnx_spdifrx_irq_handler(int irq, void *arg)
@@ -57,13 +68,13 @@
 	u32 val;
 	struct spdif_dev_data *ctx = arg;
 
-	val = readl(ctx->base + XSPDIF_IRQ_STS_REG);
-	if (val & XSPDIF_CH_STS_MASK) {
-		writel(val & XSPDIF_CH_STS_MASK,
+	val = ioread32(ctx->base + XSPDIF_IRQ_STS_REG);
+	if (val & XSPDIF_IRQ_STS_CH_STS_MASK) {
+		writel(val & XSPDIF_IRQ_STS_CH_STS_MASK,
 		       ctx->base + XSPDIF_IRQ_STS_REG);
-		val = readl(ctx->base +
-			    XSPDIF_IRQ_ENABLE_REG);
-		writel(val & ~XSPDIF_CH_STS_MASK,
+		val = ioread32(ctx->base +
+			       XSPDIF_IRQ_ENABLE_REG);
+		writel(val & ~XSPDIF_IRQ_STS_CH_STS_MASK,
 		       ctx->base + XSPDIF_IRQ_ENABLE_REG);
 
 		ctx->rx_chsts_updated = true;
@@ -80,15 +91,15 @@
 	u32 val;
 	struct spdif_dev_data *ctx = dev_get_drvdata(dai->dev);
 
-	val = readl(ctx->base + XSPDIF_CONTROL_REG);
-	val |= XSPDIF_FIFO_FLUSH_MASK;
+	val = ioread32(ctx->base + XSPDIF_CONTROL_REG);
+	val |= XSPDIF_CONTROL_FIFO_FLUSH_MASK;
 	writel(val, ctx->base + XSPDIF_CONTROL_REG);
 
 	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) {
-		writel(XSPDIF_CH_STS_MASK,
+		writel(XSPDIF_IRQ_STS_CH_STS_MASK,
 		       ctx->base + XSPDIF_IRQ_ENABLE_REG);
-		writel(XSPDIF_GLOBAL_IRQ_ENABLE,
-		       ctx->base + XSPDIF_GLOBAL_IRQ_ENABLE_REG);
+		writel(XSPDIF_GLOBAL_IRQ_ENABLE_MASK,
+		       ctx->base + XSPDIF_GLOBAL_IRQ_REG);
 	}
 
 	return 0;
@@ -99,7 +110,7 @@
 {
 	struct spdif_dev_data *ctx = dev_get_drvdata(dai->dev);
 
-	writel(XSPDIF_SOFT_RESET_VALUE, ctx->base + XSPDIF_SOFT_RESET_REG);
+	writel(XSPDIF_SOFT_RESET_VAL, ctx->base + XSPDIF_SOFT_RESET_REG);
 }
 
 static int xlnx_spdif_hw_params(struct snd_pcm_substream *substream,
@@ -109,38 +120,40 @@
 	u32 val, clk_div, clk_cfg;
 	struct spdif_dev_data *ctx = dev_get_drvdata(dai->dev);
 
-	clk_div = DIV_ROUND_CLOSEST(ctx->aclk, MAX_CHANNELS * AES_SAMPLE_WIDTH *
+	ctx->aclk = clk_get_rate(ctx->aud_clk);
+	clk_div = DIV_ROUND_CLOSEST(ctx->aclk, XSPDIF_MAX_CHANNELS *
+				    XSPDIF_AES_SAMPLE_WIDTH *
 				    params_rate(params));
 
 	switch (clk_div) {
 	case 4:
-		clk_cfg = 0;
+		clk_cfg = CLK_DIV_BY_4;
 		break;
 	case 8:
-		clk_cfg = 1;
+		clk_cfg = CLK_DIV_BY_8;
 		break;
 	case 16:
-		clk_cfg = 2;
+		clk_cfg = CLK_DIV_BY_16;
 		break;
 	case 24:
-		clk_cfg = 3;
+		clk_cfg = CLK_DIV_BY_24;
 		break;
 	case 32:
-		clk_cfg = 4;
+		clk_cfg = CLK_DIV_BY_32;
 		break;
 	case 48:
-		clk_cfg = 5;
+		clk_cfg = CLK_DIV_BY_48;
 		break;
 	case 64:
-		clk_cfg = 6;
+		clk_cfg = CLK_DIV_BY_64;
 		break;
 	default:
 		return -EINVAL;
 	}
 
-	val = readl(ctx->base + XSPDIF_CONTROL_REG);
-	val &= ~XSPDIF_CLOCK_CONFIG_BITS_MASK;
-	val |= clk_cfg << XSPDIF_CLOCK_CONFIG_BITS_SHIFT;
+	val = ioread32(ctx->base + XSPDIF_CONTROL_REG);
+	val &= ~XSPDIF_CONTROL_CLK_CFG_MASK;
+	val |= clk_cfg << XSPDIF_CONTROL_CLK_CFG_SHIFT;
 	writel(val, ctx->base + XSPDIF_CONTROL_REG);
 
 	return 0;
@@ -150,7 +163,7 @@
 {
 	int err;
 	struct spdif_dev_data *ctx = dev_get_drvdata(dai->dev);
-	unsigned long jiffies = msecs_to_jiffies(CH_STATUS_UPDATE_TIMEOUT);
+	unsigned long jiffies = msecs_to_jiffies(XSPDIF_CH_STS_UPDATE_TIMEOUT);
 
 	/* start capture only if stream is detected within 40ms timeout */
 	err = wait_event_interruptible_timeout(ctx->chsts_q,
@@ -172,12 +185,12 @@
 	int ret = 0;
 	struct spdif_dev_data *ctx = dev_get_drvdata(dai->dev);
 
-	val = readl(ctx->base + XSPDIF_CONTROL_REG);
+	val = ioread32(ctx->base + XSPDIF_CONTROL_REG);
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_START:
 	case SNDRV_PCM_TRIGGER_RESUME:
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
-		val |= XSPDIF_CORE_ENABLE_MASK;
+		val |= XSPDIF_CONTROL_ENABLE_MASK;
 		writel(val, ctx->base + XSPDIF_CONTROL_REG);
 		if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
 			ret = rx_stream_detect(dai);
@@ -185,7 +198,7 @@
 	case SNDRV_PCM_TRIGGER_STOP:
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
-		val &= ~XSPDIF_CORE_ENABLE_MASK;
+		val &= ~XSPDIF_CONTROL_ENABLE_MASK;
 		writel(val, ctx->base + XSPDIF_CONTROL_REG);
 		break;
 	default:
@@ -263,21 +276,34 @@
 	ctx->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(ctx->base)) {
 		ret = PTR_ERR(ctx->base);
-		goto clk_err;
+		goto axi_clk_err;
 	}
 	ret = of_property_read_u32(node, "xlnx,spdif-mode", &ctx->mode);
 	if (ret < 0) {
 		dev_err(dev, "cannot get SPDIF mode\n");
-		goto clk_err;
+		goto axi_clk_err;
 	}
 	if (ctx->mode) {
+		ctx->axis_clk = devm_clk_get(dev, "s_axis_aclk");
+		if (IS_ERR(ctx->axis_clk)) {
+			ret = PTR_ERR(ctx->axis_clk);
+			dev_err(dev, "failed to get s_axis_aclk(%d)\n", ret);
+			goto axi_clk_err;
+		}
 		dai_drv = &xlnx_spdif_tx_dai;
 	} else {
+		ctx->axis_clk = devm_clk_get(dev, "m_axis_aclk");
+		if (IS_ERR(ctx->axis_clk)) {
+			ret = PTR_ERR(ctx->axis_clk);
+			dev_err(dev, "failed to get m_axis_aclk(%d)\n", ret);
+			goto axi_clk_err;
+		}
+
 		res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 		if (!res) {
 			dev_err(dev, "No IRQ resource found\n");
 			ret = -ENODEV;
-			goto clk_err;
+			goto axi_clk_err;
 		}
 		ret = devm_request_irq(dev, res->start,
 				       xlnx_spdifrx_irq_handler,
@@ -285,17 +311,30 @@
 		if (ret) {
 			dev_err(dev, "spdif rx irq request failed\n");
 			ret = -ENODEV;
-			goto clk_err;
+			goto axi_clk_err;
 		}
 
 		init_waitqueue_head(&ctx->chsts_q);
 		dai_drv = &xlnx_spdif_rx_dai;
 	}
 
-	ret = of_property_read_u32(node, "xlnx,aud_clk_i", &ctx->aclk);
-	if (ret < 0) {
-		dev_err(dev, "cannot get aud_clk_i value\n");
-		goto clk_err;
+	ctx->aud_clk = devm_clk_get(dev, "aud_clk_i");
+	if (IS_ERR(ctx->aud_clk)) {
+		ret = PTR_ERR(ctx->aud_clk);
+		dev_err(dev, "failed to get aud_aclk(%d)\n", ret);
+		goto axi_clk_err;
+	}
+
+	ret = clk_prepare_enable(ctx->axis_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable axis_aclk(%d)\n", ret);
+		goto axi_clk_err;
+	}
+
+	ret = clk_prepare_enable(ctx->aud_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable aud_aclk(%d)\n", ret);
+		goto axis_clk_err;
 	}
 
 	dev_set_drvdata(dev, ctx);
@@ -307,11 +346,17 @@
 		goto clk_err;
 	}
 
-	writel(XSPDIF_SOFT_RESET_VALUE, ctx->base + XSPDIF_SOFT_RESET_REG);
+	writel(XSPDIF_SOFT_RESET_VAL, ctx->base + XSPDIF_SOFT_RESET_REG);
 	dev_info(dev, "%s DAI registered\n", dai_drv->name);
+	return 0;
 
 clk_err:
+	clk_disable_unprepare(ctx->aud_clk);
+axis_clk_err:
+	clk_disable_unprepare(ctx->axis_clk);
+axi_clk_err:
 	clk_disable_unprepare(ctx->axi_clk);
+
 	return ret;
 }
 
@@ -319,6 +364,8 @@
 {
 	struct spdif_dev_data *ctx = dev_get_drvdata(&pdev->dev);
 
+	clk_disable_unprepare(ctx->aud_clk);
+	clk_disable_unprepare(ctx->axis_clk);
 	clk_disable_unprepare(ctx->axi_clk);
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/spi/at73c213.c
+++ linux-xilinx-zynqmp-5.15.0/sound/spi/at73c213.c
@@ -218,7 +218,9 @@
 	runtime->hw = snd_at73c213_playback_hw;
 	chip->substream = substream;
 
-	clk_enable(chip->ssc->clk);
+	err = clk_enable(chip->ssc->clk);
+	if (err)
+		return err;
 
 	return 0;
 }
@@ -776,7 +778,9 @@
 		goto out;
 
 	/* Enable DAC master clock. */
-	clk_enable(chip->board->dac_clk);
+	retval = clk_enable(chip->board->dac_clk);
+	if (retval)
+		goto out;
 
 	/* Initialize at73c213 on SPI bus. */
 	retval = snd_at73c213_write_reg(chip, DAC_RST, 0x04);
@@ -889,7 +893,9 @@
 	chip->card = card;
 	chip->irq = -1;
 
-	clk_enable(chip->ssc->clk);
+	retval = clk_enable(chip->ssc->clk);
+	if (retval)
+		return retval;
 
 	retval = request_irq(irq, snd_at73c213_interrupt, 0, "at73c213", chip);
 	if (retval) {
@@ -1008,7 +1014,9 @@
 	int retval;
 
 	/* Stop playback. */
-	clk_enable(chip->ssc->clk);
+	retval = clk_enable(chip->ssc->clk);
+	if (retval)
+		goto out;
 	ssc_writel(chip->ssc->regs, CR, SSC_BIT(CR_TXDIS));
 	clk_disable(chip->ssc->clk);
 
@@ -1088,9 +1096,16 @@
 {
 	struct snd_card *card = dev_get_drvdata(dev);
 	struct snd_at73c213 *chip = card->private_data;
+	int retval;
 
-	clk_enable(chip->board->dac_clk);
-	clk_enable(chip->ssc->clk);
+	retval = clk_enable(chip->board->dac_clk);
+	if (retval)
+		return retval;
+	retval = clk_enable(chip->ssc->clk);
+	if (retval) {
+		clk_disable(chip->board->dac_clk);
+		return retval;
+	}
 	ssc_writel(chip->ssc->regs, CR, SSC_BIT(CR_TXEN));
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/synth/emux/emux.c
+++ linux-xilinx-zynqmp-5.15.0/sound/synth/emux/emux.c
@@ -88,7 +88,7 @@
 	emu->name = kstrdup(name, GFP_KERNEL);
 	emu->voices = kcalloc(emu->max_voices, sizeof(struct snd_emux_voice),
 			      GFP_KERNEL);
-	if (emu->voices == NULL)
+	if (emu->name == NULL || emu->voices == NULL)
 		return -ENOMEM;
 
 	/* create soundfont list */
@@ -126,15 +126,10 @@
  */
 int snd_emux_free(struct snd_emux *emu)
 {
-	unsigned long flags;
-
 	if (! emu)
 		return -EINVAL;
 
-	spin_lock_irqsave(&emu->voice_lock, flags);
-	if (emu->timer_active)
-		del_timer(&emu->tlist);
-	spin_unlock_irqrestore(&emu->voice_lock, flags);
+	del_timer_sync(&emu->tlist);
 
 	snd_emux_proc_free(emu);
 	snd_emux_delete_virmidi(emu);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/synth/emux/emux_nrpn.c
+++ linux-xilinx-zynqmp-5.15.0/sound/synth/emux/emux_nrpn.c
@@ -349,6 +349,9 @@
 snd_emux_xg_control(struct snd_emux_port *port, struct snd_midi_channel *chan,
 		    int param)
 {
+	if (param >= ARRAY_SIZE(chan->control))
+		return -EINVAL;
+
 	return send_converted_effect(xg_effects, ARRAY_SIZE(xg_effects),
 				     port, chan, param,
 				     chan->control[param],
--- linux-xilinx-zynqmp-5.15.0.orig/sound/synth/emux/soundfont.c
+++ linux-xilinx-zynqmp-5.15.0/sound/synth/emux/soundfont.c
@@ -701,7 +701,6 @@
 	struct snd_soundfont *sf;
 	struct soundfont_sample_info sample_info;
 	struct snd_sf_sample *sp;
-	long off;
 
 	/* patch must be opened */
 	sf = sflist->currsf;
@@ -711,12 +710,16 @@
 	if (is_special_type(sf->type))
 		return -EINVAL;
 
+	if (count < (long)sizeof(sample_info)) {
+		return -EINVAL;
+	}
 	if (copy_from_user(&sample_info, data, sizeof(sample_info)))
 		return -EFAULT;
+	data += sizeof(sample_info);
+	count -= sizeof(sample_info);
 
-	off = sizeof(sample_info);
-
-	if (sample_info.size != (count-off)/2)
+	// SoundFont uses S16LE samples.
+	if (sample_info.size * 2 != count)
 		return -EINVAL;
 
 	/* Check for dup */
@@ -744,7 +747,7 @@
 		int  rc;
 		rc = sflist->callback.sample_new
 			(sflist->callback.private_data, sp, sflist->memhdr,
-			 data + off, count - off);
+			 data, count);
 		if (rc < 0) {
 			sf_sample_delete(sflist, sf, sp);
 			return rc;
@@ -957,10 +960,12 @@
 	}
 	if (copy_from_user(&patch, data, sizeof(patch)))
 		return -EFAULT;
-	
 	count -= sizeof(patch);
 	data += sizeof(patch);
 
+	if ((patch.len << (patch.mode & WAVE_16_BITS ? 1 : 0)) != count)
+		return -EINVAL;
+
 	sf = newsf(sflist, SNDRV_SFNT_PAT_TYPE_GUS|SNDRV_SFNT_PAT_SHARED, NULL);
 	if (sf == NULL)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/6fire/chip.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/6fire/chip.c
@@ -61,8 +61,10 @@
 	}
 }
 
-static void usb6fire_chip_destroy(struct sfire_chip *chip)
+static void usb6fire_card_free(struct snd_card *card)
 {
+	struct sfire_chip *chip = card->private_data;
+
 	if (chip) {
 		if (chip->pcm)
 			usb6fire_pcm_destroy(chip);
@@ -72,8 +74,6 @@
 			usb6fire_comm_destroy(chip);
 		if (chip->control)
 			usb6fire_control_destroy(chip);
-		if (chip->card)
-			snd_card_free(chip->card);
 	}
 }
 
@@ -136,6 +136,7 @@
 	chip->regidx = regidx;
 	chip->intf_count = 1;
 	chip->card = card;
+	card->private_free = usb6fire_card_free;
 
 	ret = usb6fire_comm_init(chip);
 	if (ret < 0)
@@ -162,7 +163,7 @@
 	return 0;
 
 destroy_chip:
-	usb6fire_chip_destroy(chip);
+	snd_card_free(card);
 	return ret;
 }
 
@@ -181,7 +182,6 @@
 
 			chip->shutdown = true;
 			usb6fire_chip_abort(chip);
-			usb6fire_chip_destroy(chip);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/6fire/comm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/6fire/comm.c
@@ -95,7 +95,7 @@
 	int actual_len;
 
 	ret = usb_interrupt_msg(dev, usb_sndintpipe(dev, COMM_EP),
-			buffer, buffer[1] + 2, &actual_len, HZ);
+			buffer, buffer[1] + 2, &actual_len, 1000);
 	if (ret < 0)
 		return ret;
 	else if (actual_len != buffer[1] + 2)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/6fire/firmware.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/6fire/firmware.c
@@ -160,7 +160,7 @@
 {
 	return usb_control_msg_send(device, 0, type,
 				    USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-				    value, 0, data, len, HZ, GFP_KERNEL);
+				    value, 0, data, len, 1000, GFP_KERNEL);
 }
 
 static int usb6fire_fw_ezusb_read(struct usb_device *device,
@@ -168,7 +168,7 @@
 {
 	return usb_control_msg_recv(device, 0, type,
 				    USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-				    value, 0, data, len, HZ, GFP_KERNEL);
+				    value, 0, data, len, 1000, GFP_KERNEL);
 }
 
 static int usb6fire_fw_fpga_write(struct usb_device *device,
@@ -178,7 +178,7 @@
 	int ret;
 
 	ret = usb_bulk_msg(device, usb_sndbulkpipe(device, FPGA_EP), data, len,
-			&actual_len, HZ);
+			&actual_len, 1000);
 	if (ret < 0)
 		return ret;
 	else if (actual_len != len)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/bcd2000/bcd2000.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/bcd2000/bcd2000.c
@@ -348,7 +348,8 @@
 static void bcd2000_free_usb_related_resources(struct bcd2000 *bcd2k,
 						struct usb_interface *interface)
 {
-	/* usb_kill_urb not necessary, urb is aborted automatically */
+	usb_kill_urb(bcd2k->midi_out_urb);
+	usb_kill_urb(bcd2k->midi_in_urb);
 
 	usb_free_urb(bcd2k->midi_out_urb);
 	usb_free_urb(bcd2k->midi_in_urb);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/caiaq/audio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/caiaq/audio.c
@@ -869,14 +869,20 @@
 	return 0;
 }
 
-void snd_usb_caiaq_audio_free(struct snd_usb_caiaqdev *cdev)
+void snd_usb_caiaq_audio_disconnect(struct snd_usb_caiaqdev *cdev)
 {
 	struct device *dev = caiaqdev_to_dev(cdev);
 
 	dev_dbg(dev, "%s(%p)\n", __func__, cdev);
 	stream_stop(cdev);
+}
+
+void snd_usb_caiaq_audio_free(struct snd_usb_caiaqdev *cdev)
+{
+	struct device *dev = caiaqdev_to_dev(cdev);
+
+	dev_dbg(dev, "%s(%p)\n", __func__, cdev);
 	free_urbs(cdev->data_urbs_in);
 	free_urbs(cdev->data_urbs_out);
 	kfree(cdev->data_cb_info);
 }
-
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/caiaq/audio.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/caiaq/audio.h
@@ -3,6 +3,7 @@
 #define CAIAQ_AUDIO_H
 
 int snd_usb_caiaq_audio_init(struct snd_usb_caiaqdev *cdev);
+void snd_usb_caiaq_audio_disconnect(struct snd_usb_caiaqdev *cdev);
 void snd_usb_caiaq_audio_free(struct snd_usb_caiaqdev *cdev);
 
 #endif /* CAIAQ_AUDIO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/caiaq/device.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/caiaq/device.c
@@ -376,6 +376,17 @@
 		dev_err(dev, "Unable to set up control system (ret=%d)\n", ret);
 }
 
+static void card_free(struct snd_card *card)
+{
+	struct snd_usb_caiaqdev *cdev = caiaqdev(card);
+
+#ifdef CONFIG_SND_USB_CAIAQ_INPUT
+	snd_usb_caiaq_input_free(cdev);
+#endif
+	snd_usb_caiaq_audio_free(cdev);
+	usb_reset_device(cdev->chip.dev);
+}
+
 static int create_card(struct usb_device *usb_dev,
 		       struct usb_interface *intf,
 		       struct snd_card **cardp)
@@ -489,6 +500,7 @@
 		       cdev->vendor_name, cdev->product_name, usbpath);
 
 	setup_card(cdev);
+	card->private_free = card_free;
 	return 0;
 
  err_kill_urb:
@@ -534,15 +546,14 @@
 	snd_card_disconnect(card);
 
 #ifdef CONFIG_SND_USB_CAIAQ_INPUT
-	snd_usb_caiaq_input_free(cdev);
+	snd_usb_caiaq_input_disconnect(cdev);
 #endif
-	snd_usb_caiaq_audio_free(cdev);
+	snd_usb_caiaq_audio_disconnect(cdev);
 
 	usb_kill_urb(&cdev->ep1_in_urb);
 	usb_kill_urb(&cdev->midi_out_urb);
 
-	snd_card_free(card);
-	usb_reset_device(interface_to_usbdev(intf));
+	snd_card_free_when_closed(card);
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/caiaq/input.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/caiaq/input.c
@@ -804,6 +804,7 @@
 
 	default:
 		/* no input methods supported on this device */
+		ret = -EINVAL;
 		goto exit_free_idev;
 	}
 
@@ -828,15 +829,21 @@
 	return ret;
 }
 
-void snd_usb_caiaq_input_free(struct snd_usb_caiaqdev *cdev)
+void snd_usb_caiaq_input_disconnect(struct snd_usb_caiaqdev *cdev)
 {
 	if (!cdev || !cdev->input_dev)
 		return;
 
 	usb_kill_urb(cdev->ep4_in_urb);
+	input_unregister_device(cdev->input_dev);
+}
+
+void snd_usb_caiaq_input_free(struct snd_usb_caiaqdev *cdev)
+{
+	if (!cdev || !cdev->input_dev)
+		return;
+
 	usb_free_urb(cdev->ep4_in_urb);
 	cdev->ep4_in_urb = NULL;
-
-	input_unregister_device(cdev->input_dev);
 	cdev->input_dev = NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/caiaq/input.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/caiaq/input.h
@@ -4,6 +4,7 @@
 
 void snd_usb_caiaq_input_dispatch(struct snd_usb_caiaqdev *cdev, char *buf, unsigned int len);
 int snd_usb_caiaq_input_init(struct snd_usb_caiaqdev *cdev);
+void snd_usb_caiaq_input_disconnect(struct snd_usb_caiaqdev *cdev);
 void snd_usb_caiaq_input_free(struct snd_usb_caiaqdev *cdev);
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/card.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/card.c
@@ -382,11 +382,25 @@
 	/* Creative/Toshiba Multimedia Center SB-0500 */
 	DEVICE_NAME(0x041e, 0x3048, "Toshiba", "SB-0500"),
 
+	/* Logitech Audio Devices */
+	DEVICE_NAME(0x046d, 0x0867, "Logitech, Inc.", "Logi-MeetUp"),
+	DEVICE_NAME(0x046d, 0x0874, "Logitech, Inc.", "Logi-Tap-Audio"),
+	DEVICE_NAME(0x046d, 0x087c, "Logitech, Inc.", "Logi-Huddle"),
+	DEVICE_NAME(0x046d, 0x0898, "Logitech, Inc.", "Logi-RB-Audio"),
+	DEVICE_NAME(0x046d, 0x08d2, "Logitech, Inc.", "Logi-RBM-Audio"),
 	DEVICE_NAME(0x046d, 0x0990, "Logitech, Inc.", "QuickCam Pro 9000"),
 
 	DEVICE_NAME(0x05e1, 0x0408, "Syntek", "STK1160"),
 	DEVICE_NAME(0x05e1, 0x0480, "Hauppauge", "Woodbury"),
 
+	/* ASUS ROG Zenith II: this machine has also two devices, one for
+	 * the front headphone and another for the rest
+	 */
+	PROFILE_NAME(0x0b05, 0x1915, "ASUS", "Zenith II Front Headphone",
+		     "Zenith-II-Front-Headphone"),
+	PROFILE_NAME(0x0b05, 0x1916, "ASUS", "Zenith II Main Audio",
+		     "Zenith-II-Main-Audio"),
+
 	/* ASUS ROG Strix */
 	PROFILE_NAME(0x0b05, 0x1917,
 		     "Realtek", "ALC1220-VB-DT", "Realtek-ALC1220-VB-Desktop"),
@@ -635,6 +649,7 @@
 	INIT_LIST_HEAD(&chip->pcm_list);
 	INIT_LIST_HEAD(&chip->ep_list);
 	INIT_LIST_HEAD(&chip->iface_ref_list);
+	INIT_LIST_HEAD(&chip->clock_ref_list);
 	INIT_LIST_HEAD(&chip->midi_list);
 	INIT_LIST_HEAD(&chip->mixer_list);
 
@@ -681,7 +696,7 @@
 	return false;
 }
 
-static bool check_delayed_register_option(struct snd_usb_audio *chip, int iface)
+static int check_delayed_register_option(struct snd_usb_audio *chip)
 {
 	int i;
 	unsigned int id, inum;
@@ -690,14 +705,31 @@
 		if (delayed_register[i] &&
 		    sscanf(delayed_register[i], "%x:%x", &id, &inum) == 2 &&
 		    id == chip->usb_id)
-			return inum != iface;
+			return inum;
 	}
 
-	return false;
+	return -1;
 }
 
 static const struct usb_device_id usb_audio_ids[]; /* defined below */
 
+/* look for the last interface that matches with our ids and remember it */
+static void find_last_interface(struct snd_usb_audio *chip)
+{
+	struct usb_host_config *config = chip->dev->actconfig;
+	struct usb_interface *intf;
+	int i;
+
+	if (!config)
+		return;
+	for (i = 0; i < config->desc.bNumInterfaces; i++) {
+		intf = config->interface[i];
+		if (usb_match_id(intf, usb_audio_ids))
+			chip->last_iface = intf->altsetting[0].desc.bInterfaceNumber;
+	}
+	usb_audio_dbg(chip, "Found last interface = %d\n", chip->last_iface);
+}
+
 /* look for the corresponding quirk */
 static const struct snd_usb_audio_quirk *
 get_alias_quirk(struct usb_device *dev, unsigned int id)
@@ -716,6 +748,18 @@
 	return NULL;
 }
 
+/* register card if we reach to the last interface or to the specified
+ * one given via option
+ */
+static int try_to_register_card(struct snd_usb_audio *chip, int ifnum)
+{
+	if (check_delayed_register_option(chip) == ifnum ||
+	    chip->last_iface == ifnum ||
+	    usb_interface_claimed(usb_ifnum_to_if(chip->dev, chip->last_iface)))
+		return snd_card_register(chip->card);
+	return 0;
+}
+
 /*
  * probe the active usb device
  *
@@ -804,6 +848,7 @@
 			err = -ENODEV;
 			goto __error;
 		}
+		find_last_interface(chip);
 	}
 
 	if (chip->num_interfaces >= MAX_CARD_INTERFACES) {
@@ -853,15 +898,9 @@
 		chip->need_delayed_register = false; /* clear again */
 	}
 
-	/* we are allowed to call snd_card_register() many times, but first
-	 * check to see if a device needs to skip it or do anything special
-	 */
-	if (!snd_usb_registration_quirk(chip, ifnum) &&
-	    !check_delayed_register_option(chip, ifnum)) {
-		err = snd_card_register(chip->card);
-		if (err < 0)
-			goto __error;
-	}
+	err = try_to_register_card(chip, ifnum);
+	if (err < 0)
+		goto __error_no_register;
 
 	if (chip->quirk_flags & QUIRK_FLAG_SHARE_MEDIA_DEVICE) {
 		/* don't want to fail when snd_media_device_create() fails */
@@ -880,6 +919,11 @@
 	return 0;
 
  __error:
+	/* in the case of error in secondary interface, still try to register */
+	if (chip)
+		try_to_register_card(chip, ifnum);
+
+ __error_no_register:
 	if (chip) {
 		/* chip->active is inside the chip->card object,
 		 * decrement before memory is possibly returned.
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/card.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/card.h
@@ -44,6 +44,7 @@
 
 struct snd_usb_substream;
 struct snd_usb_iface_ref;
+struct snd_usb_clock_ref;
 struct snd_usb_endpoint;
 struct snd_usb_power_domain;
 
@@ -62,6 +63,7 @@
 struct snd_usb_endpoint {
 	struct snd_usb_audio *chip;
 	struct snd_usb_iface_ref *iface_ref;
+	struct snd_usb_clock_ref *clock_ref;
 
 	int opened;		/* open refcount; protect with chip->mutex */
 	atomic_t running;	/* running status */
@@ -74,8 +76,9 @@
 
 	atomic_t state;		/* running state */
 
-	void (*prepare_data_urb) (struct snd_usb_substream *subs,
-				  struct urb *urb);
+	int (*prepare_data_urb) (struct snd_usb_substream *subs,
+				 struct urb *urb,
+				 bool in_stream_lock);
 	void (*retire_data_urb) (struct snd_usb_substream *subs,
 				 struct urb *urb);
 
@@ -94,9 +97,9 @@
 	struct list_head ready_playback_urbs; /* playback URB FIFO for implicit fb */
 
 	unsigned int nurbs;		/* # urbs */
-	unsigned int nominal_queue_size; /* total buffer sizes in URBs */
 	unsigned long active_mask;	/* bitmask of active urbs */
 	unsigned long unlink_mask;	/* bitmask of unlinked urbs */
+	atomic_t submitted_urbs;	/* currently submitted urbs */
 	char *syncbuf;			/* sync buffer for all sync URBs */
 	dma_addr_t sync_dma;		/* DMA address of syncbuf */
 
@@ -125,7 +128,10 @@
 	int skip_packets;		/* quirks for devices to ignore the first n packets
 					   in a stream */
 	bool implicit_fb_sync;		/* syncs with implicit feedback */
-	bool need_setup;		/* (re-)need for configure? */
+	bool lowlatency_playback;	/* low-latency playback mode */
+	bool need_setup;		/* (re-)need for hw_params? */
+	bool need_prepare;		/* (re-)need for prepare? */
+	bool fixed_rate;		/* skip rate setup */
 
 	/* for hw constraints */
 	const struct audioformat *cur_audiofmt;
@@ -188,7 +194,7 @@
 	} dsd_dop;
 
 	bool trigger_tstamp_pending_update; /* trigger timestamp being updated from initial estimate */
-	bool early_playback_start;	/* early start needed for playback? */
+	bool lowlatency_playback;	/* low-latency playback mode */
 	struct media_ctl *media_ctl;
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/clock.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/clock.c
@@ -36,6 +36,12 @@
 	struct uac_clock_multiplier_descriptor v3;
 };
 
+/* check whether the descriptor bLength has the minimal length */
+#define DESC_LENGTH_CHECK(p, proto) \
+	((proto) == UAC_VERSION_3 ? \
+	 ((p)->v3.bLength >= sizeof((p)->v3)) :	\
+	 ((p)->v2.bLength >= sizeof((p)->v2)))
+
 #define GET_VAL(p, proto, field) \
 	((proto) == UAC_VERSION_3 ? (p)->v3.field : (p)->v2.field)
 
@@ -58,6 +64,8 @@
 {
 	union uac23_clock_source_desc *cs = p;
 
+	if (!DESC_LENGTH_CHECK(cs, proto))
+		return false;
 	return GET_VAL(cs, proto, bClockID) == id;
 }
 
@@ -65,13 +73,27 @@
 {
 	union uac23_clock_selector_desc *cs = p;
 
-	return GET_VAL(cs, proto, bClockID) == id;
+	if (!DESC_LENGTH_CHECK(cs, proto))
+		return false;
+	if (GET_VAL(cs, proto, bClockID) != id)
+		return false;
+	/* additional length check for baCSourceID array (in bNrInPins size)
+	 * and two more fields (which sizes depend on the protocol)
+	 */
+	if (proto == UAC_VERSION_3)
+		return cs->v3.bLength >= sizeof(cs->v3) + cs->v3.bNrInPins +
+			4 /* bmControls */ + 2 /* wCSelectorDescrStr */;
+	else
+		return cs->v2.bLength >= sizeof(cs->v2) + cs->v2.bNrInPins +
+			1 /* bmControls */ + 1 /* iClockSelector */;
 }
 
 static bool validate_clock_multiplier(void *p, int id, int proto)
 {
 	union uac23_clock_multiplier_desc *cs = p;
 
+	if (!DESC_LENGTH_CHECK(cs, proto))
+		return false;
 	return GET_VAL(cs, proto, bClockID) == id;
 }
 
@@ -328,8 +350,16 @@
 			if (chip->quirk_flags & QUIRK_FLAG_SKIP_CLOCK_SELECTOR)
 				return ret;
 			err = uac_clock_selector_set_val(chip, entity_id, cur);
-			if (err < 0)
+			if (err < 0) {
+				if (pins == 1) {
+					usb_audio_dbg(chip,
+						      "%s(): selector returned an error, "
+						      "assuming a firmware bug, id %d, ret %d\n",
+						      __func__, clock_id, err);
+					return ret;
+				}
 				return err;
+			}
 		}
 
 		if (!validate || ret > 0 || !chip->autoclock)
@@ -496,6 +526,10 @@
 	union uac23_clock_source_desc *cs_desc;
 
 	cs_desc = snd_usb_find_clock_source(chip, clock, fmt->protocol);
+
+	if (!cs_desc)
+		return 0;
+
 	if (fmt->protocol == UAC_VERSION_3)
 		bmControls = le32_to_cpu(cs_desc->v3.bmControls);
 	else
@@ -568,6 +602,17 @@
 		/* continue processing */
 	}
 
+	/* FIXME - TEAC devices require the immediate interface setup */
+	if (USB_ID_VENDOR(chip->usb_id) == 0x0644) {
+		bool cur_base_48k = (rate % 48000 == 0);
+		bool prev_base_48k = (prev_rate % 48000 == 0);
+		if (cur_base_48k != prev_base_48k) {
+			usb_set_interface(chip->dev, fmt->iface, fmt->altsetting);
+			if (chip->quirk_flags & QUIRK_FLAG_IFACE_DELAY)
+				msleep(50);
+		}
+	}
+
 validation:
 	/* validate clock after rate change */
 	if (!uac_clock_source_is_valid(chip, fmt, clock))
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/endpoint.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/endpoint.c
@@ -35,6 +35,16 @@
 	struct list_head list;
 };
 
+/* clock refcounting */
+struct snd_usb_clock_ref {
+	unsigned char clock;
+	atomic_t locked;
+	int opened;
+	int rate;
+	bool need_setup;
+	struct list_head list;
+};
+
 /*
  * snd_usb_endpoint is a model that abstracts everything related to an
  * USB endpoint and its streaming.
@@ -85,12 +95,13 @@
  */
 static void release_urb_ctx(struct snd_urb_ctx *u)
 {
-	if (u->buffer_size)
+	if (u->urb && u->buffer_size)
 		usb_free_coherent(u->ep->chip->dev, u->buffer_size,
 				  u->urb->transfer_buffer,
 				  u->urb->transfer_dma);
 	usb_free_urb(u->urb);
 	u->urb = NULL;
+	u->buffer_size = 0;
 }
 
 static const char *usb_error_string(int err)
@@ -148,18 +159,23 @@
  * This won't be used for implicit feedback which takes the packet size
  * returned from the sync source
  */
-static int slave_next_packet_size(struct snd_usb_endpoint *ep)
+static int slave_next_packet_size(struct snd_usb_endpoint *ep,
+				  unsigned int avail)
 {
 	unsigned long flags;
+	unsigned int phase;
 	int ret;
 
 	if (ep->fill_max)
 		return ep->maxframesize;
 
 	spin_lock_irqsave(&ep->lock, flags);
-	ep->phase = (ep->phase & 0xffff)
-		+ (ep->freqm << ep->datainterval);
-	ret = min(ep->phase >> 16, ep->maxframesize);
+	phase = (ep->phase & 0xffff) + (ep->freqm << ep->datainterval);
+	ret = min(phase >> 16, ep->maxframesize);
+	if (avail && ret >= avail)
+		ret = -EAGAIN;
+	else
+		ep->phase = phase;
 	spin_unlock_irqrestore(&ep->lock, flags);
 
 	return ret;
@@ -169,20 +185,25 @@
  * Return the number of samples to be sent in the next packet
  * for adaptive and synchronous endpoints
  */
-static int next_packet_size(struct snd_usb_endpoint *ep)
+static int next_packet_size(struct snd_usb_endpoint *ep, unsigned int avail)
 {
+	unsigned int sample_accum;
 	int ret;
 
 	if (ep->fill_max)
 		return ep->maxframesize;
 
-	ep->sample_accum += ep->sample_rem;
-	if (ep->sample_accum >= ep->pps) {
-		ep->sample_accum -= ep->pps;
+	sample_accum = ep->sample_accum + ep->sample_rem;
+	if (sample_accum >= ep->pps) {
+		sample_accum -= ep->pps;
 		ret = ep->packsize[1];
 	} else {
 		ret = ep->packsize[0];
 	}
+	if (avail && ret >= avail)
+		ret = -EAGAIN;
+	else
+		ep->sample_accum = sample_accum;
 
 	return ret;
 }
@@ -190,16 +211,27 @@
 /*
  * snd_usb_endpoint_next_packet_size: Return the number of samples to be sent
  * in the next packet
+ *
+ * If the size is equal or exceeds @avail, don't proceed but return -EAGAIN
+ * Exception: @avail = 0 for skipping the check.
  */
 int snd_usb_endpoint_next_packet_size(struct snd_usb_endpoint *ep,
-				      struct snd_urb_ctx *ctx, int idx)
+				      struct snd_urb_ctx *ctx, int idx,
+				      unsigned int avail)
 {
-	if (ctx->packet_size[idx])
-		return ctx->packet_size[idx];
-	else if (ep->sync_source)
-		return slave_next_packet_size(ep);
+	unsigned int packet;
+
+	packet = ctx->packet_size[idx];
+	if (packet) {
+		if (avail && packet >= avail)
+			return -EAGAIN;
+		return packet;
+	}
+
+	if (ep->sync_source)
+		return slave_next_packet_size(ep, avail);
 	else
-		return next_packet_size(ep);
+		return next_packet_size(ep, avail);
 }
 
 static void call_retire_callback(struct snd_usb_endpoint *ep,
@@ -263,7 +295,7 @@
 		unsigned int length;
 		int counts;
 
-		counts = snd_usb_endpoint_next_packet_size(ep, ctx, i);
+		counts = snd_usb_endpoint_next_packet_size(ep, ctx, i, 0);
 		length = counts * ep->stride; /* number of silent bytes */
 		offset = offs * ep->stride + extra * i;
 		urb->iso_frame_desc[i].offset = offset;
@@ -286,8 +318,9 @@
 /*
  * Prepare a PLAYBACK urb for submission to the bus.
  */
-static void prepare_outbound_urb(struct snd_usb_endpoint *ep,
-				 struct snd_urb_ctx *ctx)
+static int prepare_outbound_urb(struct snd_usb_endpoint *ep,
+				struct snd_urb_ctx *ctx,
+				bool in_stream_lock)
 {
 	struct urb *urb = ctx->urb;
 	unsigned char *cp = urb->transfer_buffer;
@@ -299,9 +332,9 @@
 	case SND_USB_ENDPOINT_TYPE_DATA:
 		data_subs = READ_ONCE(ep->data_subs);
 		if (data_subs && ep->prepare_data_urb)
-			ep->prepare_data_urb(data_subs, urb);
-		else /* no data provider, so send silence */
-			prepare_silent_urb(ep, ctx);
+			return ep->prepare_data_urb(data_subs, urb, in_stream_lock);
+		/* no data provider, so send silence */
+		prepare_silent_urb(ep, ctx);
 		break;
 
 	case SND_USB_ENDPOINT_TYPE_SYNC:
@@ -330,13 +363,14 @@
 
 		break;
 	}
+	return 0;
 }
 
 /*
  * Prepare a CAPTURE or SYNC urb for submission to the bus.
  */
-static inline void prepare_inbound_urb(struct snd_usb_endpoint *ep,
-				       struct snd_urb_ctx *urb_ctx)
+static int prepare_inbound_urb(struct snd_usb_endpoint *ep,
+			       struct snd_urb_ctx *urb_ctx)
 {
 	int i, offs;
 	struct urb *urb = urb_ctx->urb;
@@ -361,16 +395,22 @@
 		urb->iso_frame_desc[0].offset = 0;
 		break;
 	}
+	return 0;
 }
 
 /* notify an error as XRUN to the assigned PCM data substream */
 static void notify_xrun(struct snd_usb_endpoint *ep)
 {
 	struct snd_usb_substream *data_subs;
+	struct snd_pcm_substream *psubs;
 
 	data_subs = READ_ONCE(ep->data_subs);
-	if (data_subs && data_subs->pcm_substream)
-		snd_pcm_stop_xrun(data_subs->pcm_substream);
+	if (!data_subs)
+		return;
+	psubs = data_subs->pcm_substream;
+	if (psubs && psubs->runtime &&
+	    psubs->runtime->state == SNDRV_PCM_STATE_RUNNING)
+		snd_pcm_stop_xrun(psubs);
 }
 
 static struct snd_usb_packet_info *
@@ -396,6 +436,16 @@
 	return p;
 }
 
+static void push_back_to_ready_list(struct snd_usb_endpoint *ep,
+				    struct snd_urb_ctx *ctx)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ep->lock, flags);
+	list_add_tail(&ctx->ready_list, &ep->ready_playback_urbs);
+	spin_unlock_irqrestore(&ep->lock, flags);
+}
+
 /*
  * Send output urbs that have been prepared previously. URBs are dequeued
  * from ep->ready_playback_urbs and in case there aren't any available
@@ -406,12 +456,14 @@
  * is that host controllers don't guarantee the order in which they return
  * inbound and outbound packets to their submitters.
  *
- * This function is only used for implicit feedback endpoints. For endpoints
- * driven by dedicated sync endpoints, URBs are immediately re-submitted
- * from their completion handler.
+ * This function is used both for implicit feedback endpoints and in low-
+ * latency playback mode.
  */
-static void queue_pending_output_urbs(struct snd_usb_endpoint *ep)
+int snd_usb_queue_pending_output_urbs(struct snd_usb_endpoint *ep,
+				      bool in_stream_lock)
 {
+	bool implicit_fb = snd_usb_endpoint_implicit_feedback_sink(ep);
+
 	while (ep_state_running(ep)) {
 
 		unsigned long flags;
@@ -420,38 +472,58 @@
 		int err, i;
 
 		spin_lock_irqsave(&ep->lock, flags);
-		if (ep->next_packet_queued > 0 &&
+		if ((!implicit_fb || ep->next_packet_queued > 0) &&
 		    !list_empty(&ep->ready_playback_urbs)) {
 			/* take URB out of FIFO */
 			ctx = list_first_entry(&ep->ready_playback_urbs,
 					       struct snd_urb_ctx, ready_list);
 			list_del_init(&ctx->ready_list);
-
-			packet = next_packet_fifo_dequeue(ep);
+			if (implicit_fb)
+				packet = next_packet_fifo_dequeue(ep);
 		}
 		spin_unlock_irqrestore(&ep->lock, flags);
 
 		if (ctx == NULL)
-			return;
+			break;
 
 		/* copy over the length information */
-		for (i = 0; i < packet->packets; i++)
-			ctx->packet_size[i] = packet->packet_size[i];
+		if (implicit_fb) {
+			for (i = 0; i < packet->packets; i++)
+				ctx->packet_size[i] = packet->packet_size[i];
+		}
 
 		/* call the data handler to fill in playback data */
-		prepare_outbound_urb(ep, ctx);
+		err = prepare_outbound_urb(ep, ctx, in_stream_lock);
+		/* can be stopped during prepare callback */
+		if (unlikely(!ep_state_running(ep)))
+			break;
+		if (err < 0) {
+			/* push back to ready list again for -EAGAIN */
+			if (err == -EAGAIN) {
+				push_back_to_ready_list(ep, ctx);
+				break;
+			}
+
+			if (!in_stream_lock)
+				notify_xrun(ep);
+			return -EPIPE;
+		}
 
 		err = usb_submit_urb(ctx->urb, GFP_ATOMIC);
 		if (err < 0) {
 			usb_audio_err(ep->chip,
 				      "Unable to submit urb #%d: %d at %s\n",
 				      ctx->index, err, __func__);
-			notify_xrun(ep);
-			return;
+			if (!in_stream_lock)
+				notify_xrun(ep);
+			return -EPIPE;
 		}
 
 		set_bit(ctx->index, &ep->active_mask);
+		atomic_inc(&ep->submitted_urbs);
 	}
+
+	return 0;
 }
 
 /*
@@ -461,7 +533,6 @@
 {
 	struct snd_urb_ctx *ctx = urb->context;
 	struct snd_usb_endpoint *ep = ctx->ep;
-	unsigned long flags;
 	int err;
 
 	if (unlikely(urb->status == -ENOENT ||		/* unlinked */
@@ -482,16 +553,23 @@
 		if (unlikely(!ep_state_running(ep)))
 			goto exit_clear;
 
-		if (snd_usb_endpoint_implicit_feedback_sink(ep)) {
-			spin_lock_irqsave(&ep->lock, flags);
-			list_add_tail(&ctx->ready_list, &ep->ready_playback_urbs);
+		/* in low-latency and implicit-feedback modes, push back the
+		 * URB to ready list at first, then process as much as possible
+		 */
+		if (ep->lowlatency_playback ||
+		     snd_usb_endpoint_implicit_feedback_sink(ep)) {
+			push_back_to_ready_list(ep, ctx);
 			clear_bit(ctx->index, &ep->active_mask);
-			spin_unlock_irqrestore(&ep->lock, flags);
-			queue_pending_output_urbs(ep);
+			snd_usb_queue_pending_output_urbs(ep, false);
+			/* decrement at last, and check xrun */
+			if (atomic_dec_and_test(&ep->submitted_urbs) &&
+			    !snd_usb_endpoint_implicit_feedback_sink(ep))
+				notify_xrun(ep);
 			return;
 		}
 
-		prepare_outbound_urb(ep, ctx);
+		/* in non-lowlatency mode, no error handling for prepare */
+		prepare_outbound_urb(ep, ctx, false);
 		/* can be stopped during prepare callback */
 		if (unlikely(!ep_state_running(ep)))
 			goto exit_clear;
@@ -513,6 +591,7 @@
 
 exit_clear:
 	clear_bit(ctx->index, &ep->active_mask);
+	atomic_dec(&ep->submitted_urbs);
 }
 
 /*
@@ -537,6 +616,25 @@
 	return ip;
 }
 
+/* Similarly, a refcount object for clock */
+static struct snd_usb_clock_ref *
+clock_ref_find(struct snd_usb_audio *chip, int clock)
+{
+	struct snd_usb_clock_ref *ref;
+
+	list_for_each_entry(ref, &chip->clock_ref_list, list)
+		if (ref->clock == clock)
+			return ref;
+
+	ref = kzalloc(sizeof(*ref), GFP_KERNEL);
+	if (!ref)
+		return NULL;
+	ref->clock = clock;
+	atomic_set(&ref->locked, 0);
+	list_add_tail(&ref->list, &chip->clock_ref_list);
+	return ref;
+}
+
 /*
  * Get the existing endpoint object corresponding EP
  * Returns NULL if not present.
@@ -596,6 +694,7 @@
 	ep->type = type;
 	ep->ep_num = ep_num;
 	INIT_LIST_HEAD(&ep->ready_playback_urbs);
+	atomic_set(&ep->submitted_urbs, 0);
 
 	is_playback = ((ep_num & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT);
 	ep_num &= USB_ENDPOINT_NUMBER_MASK;
@@ -676,13 +775,15 @@
  * The endpoint needs to be closed via snd_usb_endpoint_close() later.
  *
  * Note that this function doesn't configure the endpoint.  The substream
- * needs to set it up later via snd_usb_endpoint_configure().
+ * needs to set it up later via snd_usb_endpoint_set_params() and
+ * snd_usb_endpoint_prepare().
  */
 struct snd_usb_endpoint *
 snd_usb_endpoint_open(struct snd_usb_audio *chip,
 		      const struct audioformat *fp,
 		      const struct snd_pcm_hw_params *params,
-		      bool is_sync_ep)
+		      bool is_sync_ep,
+		      bool fixed_rate)
 {
 	struct snd_usb_endpoint *ep;
 	int ep_num = is_sync_ep ? fp->sync_ep : fp->endpoint;
@@ -713,6 +814,15 @@
 			goto unlock;
 		}
 
+		if (fp->protocol != UAC_VERSION_1) {
+			ep->clock_ref = clock_ref_find(chip, fp->clock);
+			if (!ep->clock_ref) {
+				ep = NULL;
+				goto unlock;
+			}
+			ep->clock_ref->opened++;
+		}
+
 		ep->cur_audiofmt = fp;
 		ep->cur_channels = fp->channels;
 		ep->cur_rate = params_rate(params);
@@ -728,6 +838,8 @@
 
 		ep->implicit_fb_sync = fp->implicit_fb;
 		ep->need_setup = true;
+		ep->need_prepare = true;
+		ep->fixed_rate = fixed_rate;
 
 		usb_audio_dbg(chip, "  channels=%d, rate=%d, format=%s, period_bytes=%d, periods=%d, implicit_fb=%d\n",
 			      ep->cur_channels, ep->cur_rate,
@@ -781,14 +893,19 @@
  * Pass NULL to deactivate each callback.
  */
 void snd_usb_endpoint_set_callback(struct snd_usb_endpoint *ep,
-				   void (*prepare)(struct snd_usb_substream *subs,
-						   struct urb *urb),
+				   int (*prepare)(struct snd_usb_substream *subs,
+						  struct urb *urb,
+						  bool in_stream_lock),
 				   void (*retire)(struct snd_usb_substream *subs,
 						  struct urb *urb),
 				   struct snd_usb_substream *data_subs)
 {
 	ep->prepare_data_urb = prepare;
 	ep->retire_data_urb = retire;
+	if (data_subs)
+		ep->lowlatency_playback = data_subs->lowlatency_playback;
+	else
+		ep->lowlatency_playback = false;
 	WRITE_ONCE(ep->data_subs, data_subs);
 }
 
@@ -825,15 +942,21 @@
 	usb_audio_dbg(chip, "Closing EP 0x%x (count %d)\n",
 		      ep->ep_num, ep->opened);
 
-	if (!--ep->iface_ref->opened)
+	if (!--ep->iface_ref->opened &&
+		!(chip->quirk_flags & QUIRK_FLAG_IFACE_SKIP_CLOSE))
 		endpoint_set_interface(chip, ep, false);
 
 	if (!--ep->opened) {
+		if (ep->clock_ref) {
+			if (!--ep->clock_ref->opened)
+				ep->clock_ref->rate = 0;
+		}
 		ep->iface = 0;
 		ep->altsetting = 0;
 		ep->cur_audiofmt = NULL;
 		ep->cur_rate = 0;
 		ep->iface_ref = NULL;
+		ep->clock_ref = NULL;
 		usb_audio_dbg(chip, "EP 0x%x closed\n", ep->ep_num);
 	}
 	mutex_unlock(&chip->mutex);
@@ -842,9 +965,11 @@
 /* Prepare for suspening EP, called from the main suspend handler */
 void snd_usb_endpoint_suspend(struct snd_usb_endpoint *ep)
 {
-	ep->need_setup = true;
+	ep->need_prepare = true;
 	if (ep->iface_ref)
 		ep->iface_ref->need_setup = true;
+	if (ep->clock_ref)
+		ep->clock_ref->rate = 0;
 }
 
 /*
@@ -859,7 +984,7 @@
 		return 0;
 
 	do {
-		alive = bitmap_weight(&ep->active_mask, ep->nurbs);
+		alive = atomic_read(&ep->submitted_urbs);
 		if (!alive)
 			break;
 
@@ -893,9 +1018,10 @@
  *
  * This function moves the EP to STOPPING state if it's being RUNNING.
  */
-static int stop_urbs(struct snd_usb_endpoint *ep, bool force)
+static int stop_urbs(struct snd_usb_endpoint *ep, bool force, bool keep_pending)
 {
 	unsigned int i;
+	unsigned long flags;
 
 	if (!force && atomic_read(&ep->running))
 		return -EBUSY;
@@ -903,9 +1029,14 @@
 	if (!ep_state_update(ep, EP_STATE_RUNNING, EP_STATE_STOPPING))
 		return 0;
 
+	spin_lock_irqsave(&ep->lock, flags);
 	INIT_LIST_HEAD(&ep->ready_playback_urbs);
 	ep->next_packet_head = 0;
 	ep->next_packet_queued = 0;
+	spin_unlock_irqrestore(&ep->lock, flags);
+
+	if (keep_pending)
+		return 0;
 
 	for (i = 0; i < ep->nurbs; i++) {
 		if (test_bit(i, &ep->active_mask)) {
@@ -930,7 +1061,7 @@
 	snd_usb_endpoint_set_callback(ep, NULL, NULL, NULL);
 
 	/* stop and unlink urbs */
-	err = stop_urbs(ep, force);
+	err = stop_urbs(ep, force, false);
 	if (err)
 		return err;
 
@@ -1132,10 +1263,6 @@
 		INIT_LIST_HEAD(&u->ready_list);
 	}
 
-	/* total buffer bytes of all URBs plus the next queue;
-	 * referred in pcm.c
-	 */
-	ep->nominal_queue_size = maxsize * urb_packs * (ep->nurbs + 1);
 	return 0;
 
 out_of_memory:
@@ -1159,6 +1286,7 @@
 	if (!ep->syncbuf)
 		return -ENOMEM;
 
+	ep->nurbs = SYNC_URBS;
 	for (i = 0; i < SYNC_URBS; i++) {
 		struct snd_urb_ctx *u = &ep->urb[i];
 		u->index = i;
@@ -1178,8 +1306,6 @@
 		u->urb->complete = snd_complete_urb;
 	}
 
-	ep->nurbs = SYNC_URBS;
-
 	return 0;
 
 out_of_memory:
@@ -1187,23 +1313,51 @@
 	return -ENOMEM;
 }
 
+/* update the rate of the referred clock; return the actual rate */
+static int update_clock_ref_rate(struct snd_usb_audio *chip,
+				 struct snd_usb_endpoint *ep)
+{
+	struct snd_usb_clock_ref *clock = ep->clock_ref;
+	int rate = ep->cur_rate;
+
+	if (!clock || clock->rate == rate)
+		return rate;
+	if (clock->rate) {
+		if (atomic_read(&clock->locked))
+			return clock->rate;
+		if (clock->rate != rate) {
+			usb_audio_err(chip, "Mismatched sample rate %d vs %d for EP 0x%x\n",
+				      clock->rate, rate, ep->ep_num);
+			return clock->rate;
+		}
+	}
+	clock->rate = rate;
+	clock->need_setup = true;
+	return rate;
+}
+
 /*
  * snd_usb_endpoint_set_params: configure an snd_usb_endpoint
  *
+ * It's called either from hw_params callback.
  * Determine the number of URBs to be used on this endpoint.
  * An endpoint must be configured before it can be started.
  * An endpoint that is already running can not be reconfigured.
  */
-static int snd_usb_endpoint_set_params(struct snd_usb_audio *chip,
-				       struct snd_usb_endpoint *ep)
+int snd_usb_endpoint_set_params(struct snd_usb_audio *chip,
+				struct snd_usb_endpoint *ep)
 {
 	const struct audioformat *fmt = ep->cur_audiofmt;
-	int err;
+	int err = 0;
+
+	mutex_lock(&chip->mutex);
+	if (!ep->need_setup)
+		goto unlock;
 
 	/* release old buffers, if any */
 	err = release_urbs(ep, false);
 	if (err < 0)
-		return err;
+		goto unlock;
 
 	ep->datainterval = fmt->datainterval;
 	ep->maxpacksize = fmt->maxpacksize;
@@ -1241,28 +1395,62 @@
 	usb_audio_dbg(chip, "Set up %d URBS, ret=%d\n", ep->nurbs, err);
 
 	if (err < 0)
-		return err;
+		goto unlock;
 
 	/* some unit conversions in runtime */
 	ep->maxframesize = ep->maxpacksize / ep->cur_frame_bytes;
 	ep->curframesize = ep->curpacksize / ep->cur_frame_bytes;
 
+	err = update_clock_ref_rate(chip, ep);
+	if (err >= 0) {
+		ep->need_setup = false;
+		err = 0;
+	}
+
+ unlock:
+	mutex_unlock(&chip->mutex);
+	return err;
+}
+
+static int init_sample_rate(struct snd_usb_audio *chip,
+			    struct snd_usb_endpoint *ep)
+{
+	struct snd_usb_clock_ref *clock = ep->clock_ref;
+	int rate, err;
+
+	rate = update_clock_ref_rate(chip, ep);
+	if (rate < 0)
+		return rate;
+	if (clock && !clock->need_setup)
+		return 0;
+
+	if (!ep->fixed_rate) {
+		err = snd_usb_init_sample_rate(chip, ep->cur_audiofmt, rate);
+		if (err < 0) {
+			if (clock)
+				clock->rate = 0; /* reset rate */
+			return err;
+		}
+	}
+
+	if (clock)
+		clock->need_setup = false;
 	return 0;
 }
 
 /*
- * snd_usb_endpoint_configure: Configure the endpoint
+ * snd_usb_endpoint_prepare: Prepare the endpoint
  *
  * This function sets up the EP to be fully usable state.
- * It's called either from hw_params or prepare callback.
+ * It's called either from prepare callback.
  * The function checks need_setup flag, and performs nothing unless needed,
  * so it's safe to call this multiple times.
  *
  * This returns zero if unchanged, 1 if the configuration has changed,
  * or a negative error code.
  */
-int snd_usb_endpoint_configure(struct snd_usb_audio *chip,
-			       struct snd_usb_endpoint *ep)
+int snd_usb_endpoint_prepare(struct snd_usb_audio *chip,
+			     struct snd_usb_endpoint *ep)
 {
 	bool iface_first;
 	int err = 0;
@@ -1270,7 +1458,7 @@
 	mutex_lock(&chip->mutex);
 	if (WARN_ON(!ep->iface_ref))
 		goto unlock;
-	if (!ep->need_setup)
+	if (!ep->need_prepare)
 		goto unlock;
 
 	/* If the interface has been already set up, just set EP parameters */
@@ -1279,14 +1467,10 @@
 		 * to update at each EP configuration
 		 */
 		if (ep->cur_audiofmt->protocol == UAC_VERSION_1) {
-			err = snd_usb_init_sample_rate(chip, ep->cur_audiofmt,
-						       ep->cur_rate);
+			err = init_sample_rate(chip, ep);
 			if (err < 0)
 				goto unlock;
 		}
-		err = snd_usb_endpoint_set_params(chip, ep);
-		if (err < 0)
-			goto unlock;
 		goto done;
 	}
 
@@ -1310,11 +1494,7 @@
 	if (err < 0)
 		goto unlock;
 
-	err = snd_usb_init_sample_rate(chip, ep->cur_audiofmt, ep->cur_rate);
-	if (err < 0)
-		goto unlock;
-
-	err = snd_usb_endpoint_set_params(chip, ep);
+	err = init_sample_rate(chip, ep);
 	if (err < 0)
 		goto unlock;
 
@@ -1332,7 +1512,7 @@
 	ep->iface_ref->need_setup = false;
 
  done:
-	ep->need_setup = false;
+	ep->need_prepare = false;
 	err = 1;
 
 unlock:
@@ -1340,6 +1520,25 @@
 	return err;
 }
 
+/* get the current rate set to the given clock by any endpoint */
+int snd_usb_endpoint_get_clock_rate(struct snd_usb_audio *chip, int clock)
+{
+	struct snd_usb_clock_ref *ref;
+	int rate = 0;
+
+	if (!clock)
+		return 0;
+	mutex_lock(&chip->mutex);
+	list_for_each_entry(ref, &chip->clock_ref_list, list) {
+		if (ref->clock == clock) {
+			rate = ref->rate;
+			break;
+		}
+	}
+	mutex_unlock(&chip->mutex);
+	return rate;
+}
+
 /**
  * snd_usb_endpoint_start: start an snd_usb_endpoint
  *
@@ -1355,6 +1554,7 @@
  */
 int snd_usb_endpoint_start(struct snd_usb_endpoint *ep)
 {
+	bool is_playback = usb_pipeout(ep->pipe);
 	int err;
 	unsigned int i;
 
@@ -1372,6 +1572,9 @@
 	if (atomic_inc_return(&ep->running) != 1)
 		return 0;
 
+	if (ep->clock_ref)
+		atomic_inc(&ep->clock_ref->locked);
+
 	ep->active_mask = 0;
 	ep->unlink_mask = 0;
 	ep->phase = 0;
@@ -1391,13 +1594,9 @@
 
 	if (snd_usb_endpoint_implicit_feedback_sink(ep) &&
 	    !(ep->chip->quirk_flags & QUIRK_FLAG_PLAYBACK_FIRST)) {
-		for (i = 0; i < ep->nurbs; i++) {
-			struct snd_urb_ctx *ctx = ep->urb + i;
-			list_add_tail(&ctx->ready_list, &ep->ready_playback_urbs);
-		}
-
 		usb_audio_dbg(ep->chip, "No URB submission due to implicit fb sync\n");
-		return 0;
+		i = 0;
+		goto fill_rest;
 	}
 
 	for (i = 0; i < ep->nurbs; i++) {
@@ -1406,10 +1605,18 @@
 		if (snd_BUG_ON(!urb))
 			goto __error;
 
-		if (usb_pipeout(ep->pipe)) {
-			prepare_outbound_urb(ep, urb->context);
-		} else {
-			prepare_inbound_urb(ep, urb->context);
+		if (is_playback)
+			err = prepare_outbound_urb(ep, urb->context, true);
+		else
+			err = prepare_inbound_urb(ep, urb->context);
+		if (err < 0) {
+			/* stop filling at applptr */
+			if (err == -EAGAIN)
+				break;
+			usb_audio_dbg(ep->chip,
+				      "EP 0x%x: failed to prepare urb: %d\n",
+				      ep->ep_num, err);
+			goto __error;
 		}
 
 		err = usb_submit_urb(urb, GFP_ATOMIC);
@@ -1420,14 +1627,29 @@
 			goto __error;
 		}
 		set_bit(i, &ep->active_mask);
+		atomic_inc(&ep->submitted_urbs);
+	}
+
+	if (!i) {
+		usb_audio_dbg(ep->chip, "XRUN at starting EP 0x%x\n",
+			      ep->ep_num);
+		goto __error;
 	}
 
 	usb_audio_dbg(ep->chip, "%d URBs submitted for EP 0x%x\n",
-		      ep->nurbs, ep->ep_num);
+		      i, ep->ep_num);
+
+ fill_rest:
+	/* put the remaining URBs to ready list */
+	if (is_playback) {
+		for (; i < ep->nurbs; i++)
+			push_back_to_ready_list(ep, ep->urb + i);
+	}
+
 	return 0;
 
 __error:
-	snd_usb_endpoint_stop(ep);
+	snd_usb_endpoint_stop(ep, false);
 	return -EPIPE;
 }
 
@@ -1435,6 +1657,7 @@
  * snd_usb_endpoint_stop: stop an snd_usb_endpoint
  *
  * @ep: the endpoint to stop (may be NULL)
+ * @keep_pending: keep in-flight URBs
  *
  * A call to this function will decrement the running count of the endpoint.
  * In case the last user has requested the endpoint stop, the URBs will
@@ -1445,7 +1668,7 @@
  * The caller needs to synchronize the pending stop operation via
  * snd_usb_endpoint_sync_pending_stop().
  */
-void snd_usb_endpoint_stop(struct snd_usb_endpoint *ep)
+void snd_usb_endpoint_stop(struct snd_usb_endpoint *ep, bool keep_pending)
 {
 	if (!ep)
 		return;
@@ -1460,7 +1683,16 @@
 	if (!atomic_dec_return(&ep->running)) {
 		if (ep->sync_source)
 			WRITE_ONCE(ep->sync_source->sync_sink, NULL);
-		stop_urbs(ep, false);
+		stop_urbs(ep, false, keep_pending);
+		if (ep->clock_ref)
+			atomic_dec(&ep->clock_ref->locked);
+
+		if (ep->chip->quirk_flags & QUIRK_FLAG_FORCE_IFACE_RESET &&
+		    usb_pipeout(ep->pipe)) {
+			ep->need_prepare = true;
+			if (ep->iface_ref)
+				ep->iface_ref->need_setup = true;
+		}
 	}
 }
 
@@ -1487,12 +1719,16 @@
 {
 	struct snd_usb_endpoint *ep, *en;
 	struct snd_usb_iface_ref *ip, *in;
+	struct snd_usb_clock_ref *cp, *cn;
 
 	list_for_each_entry_safe(ep, en, &chip->ep_list, list)
 		kfree(ep);
 
 	list_for_each_entry_safe(ip, in, &chip->iface_ref_list, list)
 		kfree(ip);
+
+	list_for_each_entry_safe(cp, cn, &chip->clock_ref_list, list)
+		kfree(cp);
 }
 
 /*
@@ -1575,7 +1811,7 @@
 		}
 
 		spin_unlock_irqrestore(&ep->lock, flags);
-		queue_pending_output_urbs(ep);
+		snd_usb_queue_pending_output_urbs(ep, false);
 
 		return;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/endpoint.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/endpoint.h
@@ -14,11 +14,15 @@
 snd_usb_endpoint_open(struct snd_usb_audio *chip,
 		      const struct audioformat *fp,
 		      const struct snd_pcm_hw_params *params,
-		      bool is_sync_ep);
+		      bool is_sync_ep,
+		      bool fixed_rate);
 void snd_usb_endpoint_close(struct snd_usb_audio *chip,
 			    struct snd_usb_endpoint *ep);
-int snd_usb_endpoint_configure(struct snd_usb_audio *chip,
-			       struct snd_usb_endpoint *ep);
+int snd_usb_endpoint_set_params(struct snd_usb_audio *chip,
+				struct snd_usb_endpoint *ep);
+int snd_usb_endpoint_prepare(struct snd_usb_audio *chip,
+			     struct snd_usb_endpoint *ep);
+int snd_usb_endpoint_get_clock_rate(struct snd_usb_audio *chip, int clock);
 
 bool snd_usb_endpoint_compatible(struct snd_usb_audio *chip,
 				 struct snd_usb_endpoint *ep,
@@ -29,14 +33,15 @@
 			       struct snd_usb_endpoint *data_ep,
 			       struct snd_usb_endpoint *sync_ep);
 void snd_usb_endpoint_set_callback(struct snd_usb_endpoint *ep,
-				   void (*prepare)(struct snd_usb_substream *subs,
-						   struct urb *urb),
+				   int (*prepare)(struct snd_usb_substream *subs,
+						  struct urb *urb,
+						  bool in_stream_lock),
 				   void (*retire)(struct snd_usb_substream *subs,
 						  struct urb *urb),
 				   struct snd_usb_substream *data_subs);
 
 int snd_usb_endpoint_start(struct snd_usb_endpoint *ep);
-void snd_usb_endpoint_stop(struct snd_usb_endpoint *ep);
+void snd_usb_endpoint_stop(struct snd_usb_endpoint *ep, bool keep_pending);
 void snd_usb_endpoint_sync_pending_stop(struct snd_usb_endpoint *ep);
 void snd_usb_endpoint_suspend(struct snd_usb_endpoint *ep);
 int  snd_usb_endpoint_activate(struct snd_usb_endpoint *ep);
@@ -45,6 +50,9 @@
 
 int snd_usb_endpoint_implicit_feedback_sink(struct snd_usb_endpoint *ep);
 int snd_usb_endpoint_next_packet_size(struct snd_usb_endpoint *ep,
-				      struct snd_urb_ctx *ctx, int idx);
+				      struct snd_urb_ctx *ctx, int idx,
+				      unsigned int avail);
+int snd_usb_queue_pending_output_urbs(struct snd_usb_endpoint *ep,
+				      bool in_stream_lock);
 
 #endif /* __USBAUDIO_ENDPOINT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/format.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/format.c
@@ -39,8 +39,12 @@
 	case UAC_VERSION_1:
 	default: {
 		struct uac_format_type_i_discrete_descriptor *fmt = _fmt;
-		if (format >= 64)
-			return 0; /* invalid format */
+		if (format >= 64) {
+			usb_audio_info(chip,
+				       "%u:%d: invalid format type 0x%llx is detected, processed as PCM\n",
+				       fp->iface, fp->altsetting, format);
+			format = UAC_FORMAT_TYPE_I_PCM;
+		}
 		sample_width = fmt->bBitResolution;
 		sample_bytes = fmt->bSubframeSize;
 		format = 1ULL << format;
@@ -56,6 +60,8 @@
 			pcm_formats |= SNDRV_PCM_FMTBIT_SPECIAL;
 			/* flag potentially raw DSD capable altsettings */
 			fp->dsd_raw = true;
+			/* clear special format bit to avoid "unsupported format" msg below */
+			format &= ~UAC2_FORMAT_TYPE_I_RAW_DATA;
 		}
 
 		format <<= 1;
@@ -67,8 +73,11 @@
 		sample_width = as->bBitResolution;
 		sample_bytes = as->bSubslotSize;
 
-		if (format & UAC3_FORMAT_TYPE_I_RAW_DATA)
+		if (format & UAC3_FORMAT_TYPE_I_RAW_DATA) {
 			pcm_formats |= SNDRV_PCM_FMTBIT_SPECIAL;
+			/* clear special format bit to avoid "unsupported format" msg below */
+			format &= ~UAC3_FORMAT_TYPE_I_RAW_DATA;
+		}
 
 		format <<= 1;
 		break;
@@ -375,7 +384,7 @@
 		for (rate = min; rate <= max; rate += res) {
 
 			/* Filter out invalid rates on Presonus Studio 1810c */
-			if (chip->usb_id == USB_ID(0x0194f, 0x010c) &&
+			if (chip->usb_id == USB_ID(0x194f, 0x010c) &&
 			    !s1810c_valid_sample_rate(fp, rate))
 				goto skip_rate;
 
@@ -414,10 +423,12 @@
 	case USB_ID(0x0e41, 0x4242): /* Line6 Helix Rack */
 	case USB_ID(0x0e41, 0x4244): /* Line6 Helix LT */
 	case USB_ID(0x0e41, 0x4246): /* Line6 HX-Stomp */
+	case USB_ID(0x0e41, 0x4253): /* Line6 HX-Stomp XL */
 	case USB_ID(0x0e41, 0x4247): /* Line6 Pod Go */
 	case USB_ID(0x0e41, 0x4248): /* Line6 Helix >= fw 2.82 */
 	case USB_ID(0x0e41, 0x4249): /* Line6 Helix Rack >= fw 2.82 */
 	case USB_ID(0x0e41, 0x424a): /* Line6 Helix LT >= fw 2.82 */
+	case USB_ID(0x0e41, 0x424b): /* Line6 Pod Go */
 	case USB_ID(0x19f7, 0x0011): /* Rode Rodecaster Pro */
 		return set_fixed_rate(fp, 48000, SNDRV_PCM_RATE_48000);
 	}
@@ -464,9 +475,11 @@
 					   int clock)
 {
 	struct usb_device *dev = chip->dev;
+	struct usb_host_interface *alts;
 	unsigned int *table;
 	unsigned int nr_rates;
 	int i, err;
+	u32 bmControls;
 
 	/* performing the rate verification may lead to unexpected USB bus
 	 * behavior afterwards by some unknown reason.  Do this only for the
@@ -475,6 +488,24 @@
 	if (!(chip->quirk_flags & QUIRK_FLAG_VALIDATE_RATES))
 		return 0; /* don't perform the validation as default */
 
+	alts = snd_usb_get_host_interface(chip, fp->iface, fp->altsetting);
+	if (!alts)
+		return 0;
+
+	if (fp->protocol == UAC_VERSION_3) {
+		struct uac3_as_header_descriptor *as = snd_usb_find_csint_desc(
+				alts->extra, alts->extralen, NULL, UAC_AS_GENERAL);
+		bmControls = le32_to_cpu(as->bmControls);
+	} else {
+		struct uac2_as_header_descriptor *as = snd_usb_find_csint_desc(
+				alts->extra, alts->extralen, NULL, UAC_AS_GENERAL);
+		bmControls = as->bmControls;
+	}
+
+	if (!uac_v2v3_control_is_readable(bmControls,
+				UAC2_AS_VAL_ALT_SETTINGS))
+		return 0;
+
 	table = kcalloc(fp->nr_rates, sizeof(*table), GFP_KERNEL);
 	if (!table)
 		return -ENOMEM;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/implicit.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/implicit.c
@@ -15,6 +15,7 @@
 #include "usbaudio.h"
 #include "card.h"
 #include "helper.h"
+#include "pcm.h"
 #include "implicit.h"
 
 enum {
@@ -45,17 +46,12 @@
 
 /* Implicit feedback quirk table for playback */
 static const struct snd_usb_implicit_fb_match playback_implicit_fb_quirks[] = {
-	/* Generic matching */
-	IMPLICIT_FB_GENERIC_DEV(0x0499, 0x1509), /* Steinberg UR22 */
-	IMPLICIT_FB_GENERIC_DEV(0x0763, 0x2080), /* M-Audio FastTrack Ultra */
-	IMPLICIT_FB_GENERIC_DEV(0x0763, 0x2081), /* M-Audio FastTrack Ultra */
-	IMPLICIT_FB_GENERIC_DEV(0x0763, 0x2030), /* M-Audio Fast Track C400 */
-	IMPLICIT_FB_GENERIC_DEV(0x0763, 0x2031), /* M-Audio Fast Track C600 */
-
 	/* Fixed EP */
 	/* FIXME: check the availability of generic matching */
-	IMPLICIT_FB_FIXED_DEV(0x1397, 0x0001, 0x81, 1), /* Behringer UFX1604 */
-	IMPLICIT_FB_FIXED_DEV(0x1397, 0x0002, 0x81, 1), /* Behringer UFX1204 */
+	IMPLICIT_FB_FIXED_DEV(0x0763, 0x2030, 0x81, 3), /* M-Audio Fast Track C400 */
+	IMPLICIT_FB_FIXED_DEV(0x0763, 0x2031, 0x81, 3), /* M-Audio Fast Track C600 */
+	IMPLICIT_FB_FIXED_DEV(0x0763, 0x2080, 0x81, 2), /* M-Audio FastTrack Ultra */
+	IMPLICIT_FB_FIXED_DEV(0x0763, 0x2081, 0x81, 2), /* M-Audio FastTrack Ultra */
 	IMPLICIT_FB_FIXED_DEV(0x2466, 0x8010, 0x81, 2), /* Fractal Audio Axe-Fx III */
 	IMPLICIT_FB_FIXED_DEV(0x31e9, 0x0001, 0x81, 2), /* Solid State Logic SSL2 */
 	IMPLICIT_FB_FIXED_DEV(0x31e9, 0x0002, 0x81, 2), /* Solid State Logic SSL2+ */
@@ -352,7 +348,8 @@
 	}
 
 	/* Try the generic implicit fb if available */
-	if (chip->generic_implicit_fb)
+	if (chip->generic_implicit_fb ||
+	    (chip->quirk_flags & QUIRK_FLAG_GENERIC_IMPLICIT_FB))
 		return add_generic_implicit_fb(chip, fmt, alts);
 
 	/* No quirk */
@@ -389,6 +386,8 @@
 				    struct audioformat *fmt,
 				    struct usb_host_interface *alts)
 {
+	if (chip->quirk_flags & QUIRK_FLAG_SKIP_IMPLICIT_FB)
+		return 0;
 	if (fmt->endpoint & USB_DIR_IN)
 		return audioformat_capture_quirk(chip, fmt, alts);
 	else
@@ -457,7 +456,8 @@
 snd_usb_find_implicit_fb_sync_format(struct snd_usb_audio *chip,
 				     const struct audioformat *target,
 				     const struct snd_pcm_hw_params *params,
-				     int stream)
+				     int stream,
+				     bool *fixed_rate)
 {
 	struct snd_usb_substream *subs;
 	const struct audioformat *fp, *sync_fmt = NULL;
@@ -471,7 +471,7 @@
 	subs = find_matching_substream(chip, stream, target->sync_ep,
 				       target->fmt_type);
 	if (!subs)
-		return sync_fmt;
+		goto end;
 
 	high_score = 0;
 	list_for_each_entry(fp, &subs->fmt_list, list) {
@@ -485,6 +485,9 @@
 		}
 	}
 
+ end:
+	if (fixed_rate)
+		*fixed_rate = snd_usb_pcm_has_fixed_rate(subs);
 	return sync_fmt;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/implicit.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/implicit.h
@@ -9,6 +9,6 @@
 snd_usb_find_implicit_fb_sync_format(struct snd_usb_audio *chip,
 				     const struct audioformat *target,
 				     const struct snd_pcm_hw_params *params,
-				     int stream);
+				     int stream, bool *fixed_rate);
 
 #endif /* __USBAUDIO_IMPLICIT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/driver.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/driver.c
@@ -113,12 +113,12 @@
 			retval = usb_interrupt_msg(line6->usbdev,
 						usb_sndintpipe(line6->usbdev, properties->ep_ctrl_w),
 						(char *)frag_buf, frag_size,
-						&partial, LINE6_TIMEOUT * HZ);
+						&partial, LINE6_TIMEOUT);
 		} else {
 			retval = usb_bulk_msg(line6->usbdev,
 						usb_sndbulkpipe(line6->usbdev, properties->ep_ctrl_w),
 						(char *)frag_buf, frag_size,
-						&partial, LINE6_TIMEOUT * HZ);
+						&partial, LINE6_TIMEOUT);
 		}
 
 		if (retval) {
@@ -202,7 +202,7 @@
 	struct urb *urb;
 
 	/* create message: */
-	msg = kmalloc(sizeof(struct message), GFP_ATOMIC);
+	msg = kzalloc(sizeof(struct message), GFP_ATOMIC);
 	if (msg == NULL)
 		return -ENOMEM;
 
@@ -286,12 +286,14 @@
 {
 	struct usb_line6 *line6 = (struct usb_line6 *)urb->context;
 	struct midi_buffer *mb = &line6->line6midi->midibuf_in;
+	unsigned long flags;
 	int done;
 
 	if (urb->status == -ESHUTDOWN)
 		return;
 
 	if (line6->properties->capabilities & LINE6_CAP_CONTROL_MIDI) {
+		spin_lock_irqsave(&line6->line6midi->lock, flags);
 		done =
 			line6_midibuf_write(mb, urb->transfer_buffer, urb->actual_length);
 
@@ -300,11 +302,15 @@
 			dev_dbg(line6->ifcdev, "%d %d buffer overflow - message skipped\n",
 				done, urb->actual_length);
 		}
+		spin_unlock_irqrestore(&line6->line6midi->lock, flags);
 
 		for (;;) {
+			spin_lock_irqsave(&line6->line6midi->lock, flags);
 			done =
 				line6_midibuf_read(mb, line6->buffer_message,
-						LINE6_MIDI_MESSAGE_MAXLEN);
+						   LINE6_MIDI_MESSAGE_MAXLEN,
+						   LINE6_MIDIBUF_READ_RX);
+			spin_unlock_irqrestore(&line6->line6midi->lock, flags);
 
 			if (done <= 0)
 				break;
@@ -347,7 +353,7 @@
 	ret = usb_control_msg_send(usbdev, 0, 0x67,
 				   USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
 				   (datalen << 8) | 0x21, address, NULL, 0,
-				   LINE6_TIMEOUT * HZ, GFP_KERNEL);
+				   LINE6_TIMEOUT, GFP_KERNEL);
 	if (ret) {
 		dev_err(line6->ifcdev, "read request failed (error %d)\n", ret);
 		goto exit;
@@ -360,7 +366,7 @@
 		ret = usb_control_msg_recv(usbdev, 0, 0x67,
 					   USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
 					   0x0012, 0x0000, &len, 1,
-					   LINE6_TIMEOUT * HZ, GFP_KERNEL);
+					   LINE6_TIMEOUT, GFP_KERNEL);
 		if (ret) {
 			dev_err(line6->ifcdev,
 				"receive length failed (error %d)\n", ret);
@@ -387,7 +393,7 @@
 	/* receive the result: */
 	ret = usb_control_msg_recv(usbdev, 0, 0x67,
 				   USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-				   0x0013, 0x0000, data, datalen, LINE6_TIMEOUT * HZ,
+				   0x0013, 0x0000, data, datalen, LINE6_TIMEOUT,
 				   GFP_KERNEL);
 	if (ret)
 		dev_err(line6->ifcdev, "read failed (error %d)\n", ret);
@@ -417,7 +423,7 @@
 
 	ret = usb_control_msg_send(usbdev, 0, 0x67,
 				   USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
-				   0x0022, address, data, datalen, LINE6_TIMEOUT * HZ,
+				   0x0022, address, data, datalen, LINE6_TIMEOUT,
 				   GFP_KERNEL);
 	if (ret) {
 		dev_err(line6->ifcdev,
@@ -430,7 +436,7 @@
 
 		ret = usb_control_msg_recv(usbdev, 0, 0x67,
 					   USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
-					   0x0012, 0x0000, status, 1, LINE6_TIMEOUT * HZ,
+					   0x0012, 0x0000, status, 1, LINE6_TIMEOUT,
 					   GFP_KERNEL);
 		if (ret) {
 			dev_err(line6->ifcdev,
@@ -687,7 +693,7 @@
 	int ret;
 
 	/* initialize USB buffers: */
-	line6->buffer_listen = kmalloc(LINE6_BUFSIZE_LISTEN, GFP_KERNEL);
+	line6->buffer_listen = kzalloc(LINE6_BUFSIZE_LISTEN, GFP_KERNEL);
 	if (!line6->buffer_listen)
 		return -ENOMEM;
 
@@ -696,7 +702,7 @@
 		return -ENOMEM;
 
 	if (line6->properties->capabilities & LINE6_CAP_CONTROL_MIDI) {
-		line6->buffer_message = kmalloc(LINE6_MIDI_MESSAGE_MAXLEN, GFP_KERNEL);
+		line6->buffer_message = kzalloc(LINE6_MIDI_MESSAGE_MAXLEN, GFP_KERNEL);
 		if (!line6->buffer_message)
 			return -ENOMEM;
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/driver.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/driver.h
@@ -27,7 +27,7 @@
 #define LINE6_FALLBACK_INTERVAL 10
 #define LINE6_FALLBACK_MAXPACKETSIZE 16
 
-#define LINE6_TIMEOUT 1
+#define LINE6_TIMEOUT 1000
 #define LINE6_BUFSIZE_LISTEN 64
 #define LINE6_MIDI_MESSAGE_MAXLEN 256
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/midi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/midi.c
@@ -44,7 +44,8 @@
 	int req, done;
 
 	for (;;) {
-		req = min(line6_midibuf_bytes_free(mb), line6->max_packet_size);
+		req = min3(line6_midibuf_bytes_free(mb), line6->max_packet_size,
+			   LINE6_FALLBACK_MAXPACKETSIZE);
 		done = snd_rawmidi_transmit_peek(substream, chunk, req);
 
 		if (done == 0)
@@ -56,7 +57,8 @@
 
 	for (;;) {
 		done = line6_midibuf_read(mb, chunk,
-					  LINE6_FALLBACK_MAXPACKETSIZE);
+					  LINE6_FALLBACK_MAXPACKETSIZE,
+					  LINE6_MIDIBUF_READ_TX);
 
 		if (done == 0)
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/midibuf.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/midibuf.c
@@ -9,6 +9,7 @@
 
 #include "midibuf.h"
 
+
 static int midibuf_message_length(unsigned char code)
 {
 	int message_length;
@@ -20,12 +21,7 @@
 
 		message_length = length[(code >> 4) - 8];
 	} else {
-		/*
-		   Note that according to the MIDI specification 0xf2 is
-		   the "Song Position Pointer", but this is used by Line 6
-		   to send sysex messages to the host.
-		 */
-		static const int length[] = { -1, 2, -1, 2, -1, -1, 1, 1, 1, 1,
+		static const int length[] = { -1, 2, 2, 2, -1, -1, 1, 1, 1, -1,
 			1, 1, 1, -1, 1, 1
 		};
 		message_length = length[code & 0x0f];
@@ -125,7 +121,7 @@
 }
 
 int line6_midibuf_read(struct midi_buffer *this, unsigned char *data,
-		       int length)
+		       int length, int read_type)
 {
 	int bytes_used;
 	int length1, length2;
@@ -148,9 +144,22 @@
 
 	length1 = this->size - this->pos_read;
 
-	/* check MIDI command length */
 	command = this->buf[this->pos_read];
+	/*
+	   PODxt always has status byte lower nibble set to 0010,
+	   when it means to send 0000, so we correct if here so
+	   that control/program changes come on channel 1 and
+	   sysex message status byte is correct
+	 */
+	if (read_type == LINE6_MIDIBUF_READ_RX) {
+		if (command == 0xb2 || command == 0xc2 || command == 0xf2) {
+			unsigned char fixed = command & 0xf0;
+			this->buf[this->pos_read] = fixed;
+			command = fixed;
+		}
+	}
 
+	/* check MIDI command length */
 	if (command & 0x80) {
 		midi_length = midibuf_message_length(command);
 		this->command_prev = command;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/midibuf.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/midibuf.h
@@ -8,6 +8,9 @@
 #ifndef MIDIBUF_H
 #define MIDIBUF_H
 
+#define LINE6_MIDIBUF_READ_TX 0
+#define LINE6_MIDIBUF_READ_RX 1
+
 struct midi_buffer {
 	unsigned char *buf;
 	int size;
@@ -23,7 +26,7 @@
 extern int line6_midibuf_ignore(struct midi_buffer *mb, int length);
 extern int line6_midibuf_init(struct midi_buffer *mb, int size, int split);
 extern int line6_midibuf_read(struct midi_buffer *mb, unsigned char *data,
-			      int length);
+			      int length, int read_type);
 extern void line6_midibuf_reset(struct midi_buffer *mb);
 extern int line6_midibuf_write(struct midi_buffer *mb, unsigned char *data,
 			       int length);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/pod.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/pod.c
@@ -159,8 +159,9 @@
 	.bytes_per_channel = 3 /* SNDRV_PCM_FMTBIT_S24_3LE */
 };
 
+
 static const char pod_version_header[] = {
-	0xf2, 0x7e, 0x7f, 0x06, 0x02
+	0xf0, 0x7e, 0x7f, 0x06, 0x02
 };
 
 static char *pod_alloc_sysex_buffer(struct usb_line6_pod *pod, int code,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/podhd.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/podhd.c
@@ -190,7 +190,7 @@
 	ret = usb_control_msg_send(usbdev, 0,
 					0x67, USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
 					0x11, 0,
-					NULL, 0, LINE6_TIMEOUT * HZ, GFP_KERNEL);
+					NULL, 0, LINE6_TIMEOUT, GFP_KERNEL);
 	if (ret) {
 		dev_err(pod->line6.ifcdev, "read request failed (error %d)\n", ret);
 		goto exit;
@@ -200,7 +200,7 @@
 	ret = usb_control_msg_recv(usbdev, 0, 0x67,
 					USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
 					0x11, 0x0,
-					init_bytes, 3, LINE6_TIMEOUT * HZ, GFP_KERNEL);
+					init_bytes, 3, LINE6_TIMEOUT, GFP_KERNEL);
 	if (ret) {
 		dev_err(pod->line6.ifcdev,
 			"receive length failed (error %d)\n", ret);
@@ -220,7 +220,7 @@
 					USB_REQ_SET_FEATURE,
 					USB_TYPE_STANDARD | USB_RECIP_DEVICE | USB_DIR_OUT,
 					1, 0,
-					NULL, 0, LINE6_TIMEOUT * HZ, GFP_KERNEL);
+					NULL, 0, LINE6_TIMEOUT, GFP_KERNEL);
 exit:
 	return ret;
 }
@@ -507,7 +507,7 @@
 	[LINE6_PODHD500X] = {
 		.id = "PODHD500X",
 		.name = "POD HD500X",
-		.capabilities	= LINE6_CAP_CONTROL
+		.capabilities	= LINE6_CAP_CONTROL | LINE6_CAP_HWMON_CTL
 				| LINE6_CAP_PCM | LINE6_CAP_HWMON,
 		.altsetting = 1,
 		.ep_ctrl_r = 0x81,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/line6/toneport.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/line6/toneport.c
@@ -128,7 +128,7 @@
 
 	ret = usb_control_msg_send(usbdev, 0, 0x67,
 				   USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
-				   cmd1, cmd2, NULL, 0, LINE6_TIMEOUT * HZ,
+				   cmd1, cmd2, NULL, 0, LINE6_TIMEOUT,
 				   GFP_KERNEL);
 
 	if (ret) {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/midi.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/midi.c
@@ -1133,10 +1133,8 @@
 					port = &umidi->endpoints[i].out->ports[j];
 					break;
 				}
-	if (!port) {
-		snd_BUG();
+	if (!port)
 		return -ENXIO;
-	}
 
 	substream->runtime->private_data = port;
 	port->state = STATE_UNKNOWN;
@@ -1145,6 +1143,9 @@
 
 static int snd_usbmidi_output_close(struct snd_rawmidi_substream *substream)
 {
+	struct usbmidi_out_port *port = substream->runtime->private_data;
+
+	flush_work(&port->ep->work);
 	return substream_open(substream, 0, 0);
 }
 
@@ -1194,6 +1195,7 @@
 		} while (drain_urbs && timeout);
 		finish_wait(&ep->drain_wait, &wait);
 	}
+	port->active = 0;
 	spin_unlock_irq(&ep->buffer_lock);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/misc/ua101.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/misc/ua101.c
@@ -1000,7 +1000,7 @@
 		fmt_playback->bSubframeSize * ua->playback.channels;
 
 	epd = &ua->intf[INTF_CAPTURE]->altsetting[1].endpoint[0].desc;
-	if (!usb_endpoint_is_isoc_in(epd)) {
+	if (!usb_endpoint_is_isoc_in(epd) || usb_endpoint_maxp(epd) == 0) {
 		dev_err(&ua->dev->dev, "invalid capture endpoint\n");
 		return -ENXIO;
 	}
@@ -1008,7 +1008,7 @@
 	ua->capture.max_packet_bytes = usb_endpoint_maxp(epd);
 
 	epd = &ua->intf[INTF_PLAYBACK]->altsetting[1].endpoint[0].desc;
-	if (!usb_endpoint_is_isoc_out(epd)) {
+	if (!usb_endpoint_is_isoc_out(epd) || usb_endpoint_maxp(epd) == 0) {
 		dev_err(&ua->dev->dev, "invalid playback endpoint\n");
 		return -ENXIO;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/mixer.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/mixer.c
@@ -1205,6 +1205,21 @@
 			cval->res = 16;
 		}
 		break;
+	case USB_ID(0x1bcf, 0x2283): /* NexiGo N930AF FHD Webcam */
+	case USB_ID(0x03f0, 0x654a): /* HP 320 FHD Webcam */
+		if (!strcmp(kctl->id.name, "Mic Capture Volume")) {
+			usb_audio_info(chip,
+				"set resolution quirk: cval->res = 16\n");
+			cval->res = 16;
+		}
+		break;
+	case USB_ID(0x1bcf, 0x2281): /* HD Webcam */
+		if (!strcmp(kctl->id.name, "Mic Capture Volume")) {
+			usb_audio_info(chip,
+				"set resolution quirk: cval->res = 16\n");
+			cval->res = 16;
+		}
+		break;
 	}
 }
 
@@ -1332,6 +1347,19 @@
 
 #define get_min_max(cval, def)	get_min_max_with_quirks(cval, def, NULL)
 
+/* get the max value advertised via control API */
+static int get_max_exposed(struct usb_mixer_elem_info *cval)
+{
+	if (!cval->max_exposed) {
+		if (cval->res)
+			cval->max_exposed =
+				DIV_ROUND_UP(cval->max - cval->min, cval->res);
+		else
+			cval->max_exposed = cval->max - cval->min;
+	}
+	return cval->max_exposed;
+}
+
 /* get a feature/mixer unit info */
 static int mixer_ctl_feature_info(struct snd_kcontrol *kcontrol,
 				  struct snd_ctl_elem_info *uinfo)
@@ -1344,11 +1372,8 @@
 	else
 		uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
 	uinfo->count = cval->channels;
-	if (cval->val_type == USB_MIXER_BOOLEAN ||
-	    cval->val_type == USB_MIXER_INV_BOOLEAN) {
-		uinfo->value.integer.min = 0;
-		uinfo->value.integer.max = 1;
-	} else {
+	if (cval->val_type != USB_MIXER_BOOLEAN &&
+	    cval->val_type != USB_MIXER_INV_BOOLEAN) {
 		if (!cval->initialized) {
 			get_min_max_with_quirks(cval, 0, kcontrol);
 			if (cval->initialized && cval->dBmin >= cval->dBmax) {
@@ -1360,10 +1385,10 @@
 					       &kcontrol->id);
 			}
 		}
-		uinfo->value.integer.min = 0;
-		uinfo->value.integer.max =
-			DIV_ROUND_UP(cval->max - cval->min, cval->res);
 	}
+
+	uinfo->value.integer.min = 0;
+	uinfo->value.integer.max = get_max_exposed(cval);
 	return 0;
 }
 
@@ -1404,6 +1429,7 @@
 				 struct snd_ctl_elem_value *ucontrol)
 {
 	struct usb_mixer_elem_info *cval = kcontrol->private_data;
+	int max_val = get_max_exposed(cval);
 	int c, cnt, val, oval, err;
 	int changed = 0;
 
@@ -1416,6 +1442,8 @@
 			if (err < 0)
 				return filter_error(cval, err);
 			val = ucontrol->value.integer.value[cnt];
+			if (val < 0 || val > max_val)
+				return -EINVAL;
 			val = get_abs_value(cval, val);
 			if (oval != val) {
 				snd_usb_set_cur_mix_value(cval, c + 1, cnt, val);
@@ -1429,6 +1457,8 @@
 		if (err < 0)
 			return filter_error(cval, err);
 		val = ucontrol->value.integer.value[0];
+		if (val < 0 || val > max_val)
+			return -EINVAL;
 		val = get_abs_value(cval, val);
 		if (val != oval) {
 			snd_usb_set_cur_mix_value(cval, 0, 0, val);
@@ -1496,6 +1526,10 @@
 		usb_audio_err(chip,
 			"cannot get connectors status: req = %#x, wValue = %#x, wIndex = %#x, type = %d\n",
 			UAC_GET_CUR, validx, idx, cval->val_type);
+
+		if (val)
+			*val = 0;
+
 		return filter_error(cval, ret);
 	}
 
@@ -1974,6 +2008,13 @@
 		bmaControls = ftr->bmaControls;
 	}
 
+	if (channels > 32) {
+		usb_audio_info(state->chip,
+			       "usbmixer: too many channels (%d) in unit %d\n",
+			       channels, unitid);
+		return -EINVAL;
+	}
+
 	/* parse the source unit */
 	err = parse_audio_unit(state, hdr->bSourceID);
 	if (err < 0)
@@ -2283,6 +2324,8 @@
 	if (err < 0)
 		return filter_error(cval, err);
 	val = ucontrol->value.integer.value[0];
+	if (val < 0 || val > get_max_exposed(cval))
+		return -EINVAL;
 	val = get_abs_value(cval, val);
 	if (val != oval) {
 		set_cur_ctl_value(cval, cval->control << 8, val);
@@ -2645,6 +2688,8 @@
 	if (err < 0)
 		return filter_error(cval, err);
 	val = ucontrol->value.enumerated.item[0];
+	if (val < 0 || val >= cval->max) /* here cval->max = # elements */
+		return -EINVAL;
 	val = get_abs_value(cval, val);
 	if (val != oval) {
 		set_cur_ctl_value(cval, cval->control << 8, val);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/mixer.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/mixer.h
@@ -88,6 +88,7 @@
 	int channels;
 	int val_type;
 	int min, max, res;
+	int max_exposed; /* control API exposes the value in 0..max_exposed */
 	int dBmin, dBmax;
 	int cached;
 	int cache_val[MAX_CHANNELS];
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/mixer_maps.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/mixer_maps.c
@@ -366,13 +366,28 @@
 	{ 0 }
 };
 
-/* Some mobos shipped with a dummy HD-audio show the invalid GET_MIN/GET_MAX
- * response for Input Gain Pad (id=19, control=12) and the connector status
- * for SPDIF terminal (id=18).  Skip them.
- */
-static const struct usbmix_name_map asus_rog_map[] = {
-	{ 18, NULL }, /* OT, connector control */
-	{ 19, NULL, 12 }, /* FU, Input Gain Pad */
+/* ASUS ROG Zenith II with Realtek ALC1220-VB */
+static const struct usbmix_name_map asus_zenith_ii_map[] = {
+	{ 19, NULL, 12 }, /* FU, Input Gain Pad - broken response, disabled */
+	{ 16, "Speaker" },		/* OT */
+	{ 22, "Speaker Playback" },	/* FU */
+	{ 7, "Line" },			/* IT */
+	{ 19, "Line Capture" },		/* FU */
+	{ 8, "Mic" },			/* IT */
+	{ 20, "Mic Capture" },		/* FU */
+	{ 9, "Front Mic" },		/* IT */
+	{ 21, "Front Mic Capture" },	/* FU */
+	{ 17, "IEC958" },		/* OT */
+	{ 23, "IEC958 Playback" },	/* FU */
+	{}
+};
+
+static const struct usbmix_connector_map asus_zenith_ii_connector_map[] = {
+	{ 10, 16 },	/* (Back) Speaker */
+	{ 11, 17 },	/* SPDIF */
+	{ 13, 7 },	/* Line */
+	{ 14, 8 },	/* Mic */
+	{ 15, 9 },	/* Front Mic */
 	{}
 };
 
@@ -423,6 +438,14 @@
 	{}
 };
 
+/* MSI MPG X570S Carbon Max Wifi with ALC4080  */
+static const struct usbmix_name_map msi_mpg_x570s_carbon_max_wifi_alc4080_map[] = {
+	{ 29, "Speaker Playback" },
+	{ 30, "Front Headphone Playback" },
+	{ 32, "IEC958 Playback" },
+	{}
+};
+
 /*
  * Control map entries
  */
@@ -537,10 +560,30 @@
 		.map = corsair_virtuoso_map,
 	},
 	{
+		/* Corsair Virtuoso SE Latest (wired mode) */
+		.id = USB_ID(0x1b1c, 0x0a3f),
+		.map = corsair_virtuoso_map,
+	},
+	{
+		/* Corsair Virtuoso SE Latest (wireless mode) */
+		.id = USB_ID(0x1b1c, 0x0a40),
+		.map = corsair_virtuoso_map,
+	},
+	{
 		/* Corsair Virtuoso (wireless mode) */
 		.id = USB_ID(0x1b1c, 0x0a42),
 		.map = corsair_virtuoso_map,
 	},
+	{
+		/* Corsair HS80 RGB Wireless (wired mode) */
+		.id = USB_ID(0x1b1c, 0x0a6a),
+		.map = corsair_virtuoso_map,
+	},
+	{
+		/* Corsair HS80 RGB Wireless (wireless mode) */
+		.id = USB_ID(0x1b1c, 0x0a6b),
+		.map = corsair_virtuoso_map,
+	},
 	{	/* Gigabyte TRX40 Aorus Master (rear panel + front mic) */
 		.id = USB_ID(0x0414, 0xa001),
 		.map = aorus_master_alc1220vb_map,
@@ -550,9 +593,10 @@
 		.map = trx40_mobo_map,
 		.connector_map = trx40_mobo_connector_map,
 	},
-	{	/* ASUS ROG Zenith II */
+	{	/* ASUS ROG Zenith II (main audio) */
 		.id = USB_ID(0x0b05, 0x1916),
-		.map = asus_rog_map,
+		.map = asus_zenith_ii_map,
+		.connector_map = asus_zenith_ii_connector_map,
 	},
 	{	/* ASUS ROG Strix */
 		.id = USB_ID(0x0b05, 0x1917),
@@ -564,6 +608,14 @@
 		.map = trx40_mobo_map,
 		.connector_map = trx40_mobo_connector_map,
 	},
+	{	/* MSI MPG X570S Carbon Max Wifi */
+		.id = USB_ID(0x0db0, 0x419c),
+		.map = msi_mpg_x570s_carbon_max_wifi_alc4080_map,
+	},
+	{	/* MSI MAG X570S Torpedo Max */
+		.id = USB_ID(0x0db0, 0xa073),
+		.map = msi_mpg_x570s_carbon_max_wifi_alc4080_map,
+	},
 	{	/* MSI TRX40 */
 		.id = USB_ID(0x0db0, 0x543d),
 		.map = trx40_mobo_map,
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/mixer_quirks.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/mixer_quirks.c
@@ -24,6 +24,7 @@
 #include <sound/asoundef.h>
 #include <sound/core.h>
 #include <sound/control.h>
+#include <sound/hda_verbs.h>
 #include <sound/hwdep.h>
 #include <sound/info.h>
 #include <sound/tlv.h>
@@ -1934,6 +1935,169 @@
 					  NULL);
 }
 
+/*
+ * Dell WD15 dock jack detection
+ *
+ * The WD15 contains an ALC4020 USB audio controller and ALC3263 audio codec
+ * from Realtek. It is a UAC 1 device, and UAC 1 does not support jack
+ * detection. Instead, jack detection works by sending HD Audio commands over
+ * vendor-type USB messages.
+ */
+
+#define HDA_VERB_CMD(V, N, D) (((N) << 20) | ((V) << 8) | (D))
+
+#define REALTEK_HDA_VALUE 0x0038
+
+#define REALTEK_HDA_SET		62
+#define REALTEK_HDA_GET_OUT	88
+#define REALTEK_HDA_GET_IN	89
+
+#define REALTEK_LINE1			0x1a
+#define REALTEK_VENDOR_REGISTERS	0x20
+#define REALTEK_HP_OUT			0x21
+
+#define REALTEK_CBJ_CTRL2 0x50
+
+#define REALTEK_JACK_INTERRUPT_NODE 5
+
+#define REALTEK_MIC_FLAG 0x100
+
+static int realtek_hda_set(struct snd_usb_audio *chip, u32 cmd)
+{
+	struct usb_device *dev = chip->dev;
+	__be32 buf = cpu_to_be32(cmd);
+
+	return snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), REALTEK_HDA_SET,
+			       USB_RECIP_DEVICE | USB_TYPE_VENDOR | USB_DIR_OUT,
+			       REALTEK_HDA_VALUE, 0, &buf, sizeof(buf));
+}
+
+static int realtek_hda_get(struct snd_usb_audio *chip, u32 cmd, u32 *value)
+{
+	struct usb_device *dev = chip->dev;
+	int err;
+	__be32 buf = cpu_to_be32(cmd);
+
+	err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), REALTEK_HDA_GET_OUT,
+			      USB_RECIP_DEVICE | USB_TYPE_VENDOR | USB_DIR_OUT,
+			      REALTEK_HDA_VALUE, 0, &buf, sizeof(buf));
+	if (err < 0)
+		return err;
+	err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), REALTEK_HDA_GET_IN,
+			      USB_RECIP_DEVICE | USB_TYPE_VENDOR | USB_DIR_IN,
+			      REALTEK_HDA_VALUE, 0, &buf, sizeof(buf));
+	if (err < 0)
+		return err;
+
+	*value = be32_to_cpu(buf);
+	return 0;
+}
+
+static int realtek_ctl_connector_get(struct snd_kcontrol *kcontrol,
+				     struct snd_ctl_elem_value *ucontrol)
+{
+	struct usb_mixer_elem_info *cval = kcontrol->private_data;
+	struct snd_usb_audio *chip = cval->head.mixer->chip;
+	u32 pv = kcontrol->private_value;
+	u32 node_id = pv & 0xff;
+	u32 sense;
+	u32 cbj_ctrl2;
+	bool presence;
+	int err;
+
+	err = snd_usb_lock_shutdown(chip);
+	if (err < 0)
+		return err;
+	err = realtek_hda_get(chip,
+			      HDA_VERB_CMD(AC_VERB_GET_PIN_SENSE, node_id, 0),
+			      &sense);
+	if (err < 0)
+		goto err;
+	if (pv & REALTEK_MIC_FLAG) {
+		err = realtek_hda_set(chip,
+				      HDA_VERB_CMD(AC_VERB_SET_COEF_INDEX,
+						   REALTEK_VENDOR_REGISTERS,
+						   REALTEK_CBJ_CTRL2));
+		if (err < 0)
+			goto err;
+		err = realtek_hda_get(chip,
+				      HDA_VERB_CMD(AC_VERB_GET_PROC_COEF,
+						   REALTEK_VENDOR_REGISTERS, 0),
+				      &cbj_ctrl2);
+		if (err < 0)
+			goto err;
+	}
+err:
+	snd_usb_unlock_shutdown(chip);
+	if (err < 0)
+		return err;
+
+	presence = sense & AC_PINSENSE_PRESENCE;
+	if (pv & REALTEK_MIC_FLAG)
+		presence = presence && (cbj_ctrl2 & 0x0070) == 0x0070;
+	ucontrol->value.integer.value[0] = presence;
+	return 0;
+}
+
+static const struct snd_kcontrol_new realtek_connector_ctl_ro = {
+	.iface = SNDRV_CTL_ELEM_IFACE_CARD,
+	.name = "", /* will be filled later manually */
+	.access = SNDRV_CTL_ELEM_ACCESS_READ,
+	.info = snd_ctl_boolean_mono_info,
+	.get = realtek_ctl_connector_get,
+};
+
+static int realtek_resume_jack(struct usb_mixer_elem_list *list)
+{
+	snd_ctl_notify(list->mixer->chip->card, SNDRV_CTL_EVENT_MASK_VALUE,
+		       &list->kctl->id);
+	return 0;
+}
+
+static int realtek_add_jack(struct usb_mixer_interface *mixer,
+			    char *name, u32 val)
+{
+	struct usb_mixer_elem_info *cval;
+	struct snd_kcontrol *kctl;
+
+	cval = kzalloc(sizeof(*cval), GFP_KERNEL);
+	if (!cval)
+		return -ENOMEM;
+	snd_usb_mixer_elem_init_std(&cval->head, mixer,
+				    REALTEK_JACK_INTERRUPT_NODE);
+	cval->head.resume = realtek_resume_jack;
+	cval->val_type = USB_MIXER_BOOLEAN;
+	cval->channels = 1;
+	cval->min = 0;
+	cval->max = 1;
+	kctl = snd_ctl_new1(&realtek_connector_ctl_ro, cval);
+	if (!kctl) {
+		kfree(cval);
+		return -ENOMEM;
+	}
+	kctl->private_value = val;
+	strscpy(kctl->id.name, name, sizeof(kctl->id.name));
+	kctl->private_free = snd_usb_mixer_elem_free;
+	return snd_usb_mixer_add_control(&cval->head, kctl);
+}
+
+static int dell_dock_mixer_create(struct usb_mixer_interface *mixer)
+{
+	int err;
+
+	err = realtek_add_jack(mixer, "Line Out Jack", REALTEK_LINE1);
+	if (err < 0)
+		return err;
+	err = realtek_add_jack(mixer, "Headphone Jack", REALTEK_HP_OUT);
+	if (err < 0)
+		return err;
+	err = realtek_add_jack(mixer, "Headset Mic Jack",
+			       REALTEK_HP_OUT | REALTEK_MIC_FLAG);
+	if (err < 0)
+		return err;
+	return 0;
+}
+
 static void dell_dock_init_vol(struct snd_usb_audio *chip, int ch, int id)
 {
 	u16 buf = 0;
@@ -2795,6 +2959,8 @@
 #define SND_DJM_750_IDX		0x1
 #define SND_DJM_850_IDX		0x2
 #define SND_DJM_900NXS2_IDX	0x3
+#define SND_DJM_750MK2_IDX	0x4
+#define SND_DJM_450_IDX		0x5
 
 
 #define SND_DJM_CTL(_name, suffix, _default_value, _windex) { \
@@ -2925,6 +3091,31 @@
 };
 
 
+// DJM-450
+static const u16 snd_djm_opts_450_cap1[] = {
+	0x0103, 0x0100, 0x0106, 0x0107, 0x0108, 0x0109, 0x010d, 0x010a };
+
+static const u16 snd_djm_opts_450_cap2[] = {
+	0x0203, 0x0200, 0x0206, 0x0207, 0x0208, 0x0209, 0x020d, 0x020a };
+
+static const u16 snd_djm_opts_450_cap3[] = {
+	0x030a, 0x0311, 0x0312, 0x0307, 0x0308, 0x0309, 0x030d };
+
+static const u16 snd_djm_opts_450_pb1[] = { 0x0100, 0x0101, 0x0104 };
+static const u16 snd_djm_opts_450_pb2[] = { 0x0200, 0x0201, 0x0204 };
+static const u16 snd_djm_opts_450_pb3[] = { 0x0300, 0x0301, 0x0304 };
+
+static const struct snd_djm_ctl snd_djm_ctls_450[] = {
+	SND_DJM_CTL("Capture Level", cap_level, 0, SND_DJM_WINDEX_CAPLVL),
+	SND_DJM_CTL("Ch1 Input",   450_cap1, 2, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch2 Input",   450_cap2, 2, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch3 Input",   450_cap3, 0, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch1 Output",   450_pb1, 0, SND_DJM_WINDEX_PB),
+	SND_DJM_CTL("Ch2 Output",   450_pb2, 1, SND_DJM_WINDEX_PB),
+	SND_DJM_CTL("Ch3 Output",   450_pb3, 2, SND_DJM_WINDEX_PB)
+};
+
+
 // DJM-750
 static const u16 snd_djm_opts_750_cap1[] = {
 	0x0101, 0x0103, 0x0106, 0x0107, 0x0108, 0x0109, 0x010a, 0x010f };
@@ -2984,12 +3175,43 @@
 	SND_DJM_CTL("Ch5 Input",   900nxs2_cap5, 3, SND_DJM_WINDEX_CAP)
 };
 
+// DJM-750MK2
+static const u16 snd_djm_opts_750mk2_cap1[] = {
+	0x0100, 0x0102, 0x0103, 0x0106, 0x0107, 0x0108, 0x0109, 0x010a };
+static const u16 snd_djm_opts_750mk2_cap2[] = {
+	0x0200, 0x0202, 0x0203, 0x0206, 0x0207, 0x0208, 0x0209, 0x020a };
+static const u16 snd_djm_opts_750mk2_cap3[] = {
+	0x0300, 0x0302, 0x0303, 0x0306, 0x0307, 0x0308, 0x0309, 0x030a };
+static const u16 snd_djm_opts_750mk2_cap4[] = {
+	0x0400, 0x0402, 0x0403, 0x0406, 0x0407, 0x0408, 0x0409, 0x040a };
+static const u16 snd_djm_opts_750mk2_cap5[] = {
+	0x0507, 0x0508, 0x0509, 0x050a, 0x0511, 0x0512, 0x0513, 0x0514 };
+
+static const u16 snd_djm_opts_750mk2_pb1[] = { 0x0100, 0x0101, 0x0104 };
+static const u16 snd_djm_opts_750mk2_pb2[] = { 0x0200, 0x0201, 0x0204 };
+static const u16 snd_djm_opts_750mk2_pb3[] = { 0x0300, 0x0301, 0x0304 };
+
+
+static const struct snd_djm_ctl snd_djm_ctls_750mk2[] = {
+	SND_DJM_CTL("Capture Level", cap_level, 0, SND_DJM_WINDEX_CAPLVL),
+	SND_DJM_CTL("Ch1 Input",   750mk2_cap1, 2, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch2 Input",   750mk2_cap2, 2, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch3 Input",   750mk2_cap3, 2, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch4 Input",   750mk2_cap4, 2, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch5 Input",   750mk2_cap5, 3, SND_DJM_WINDEX_CAP),
+	SND_DJM_CTL("Ch1 Output",   750mk2_pb1, 0, SND_DJM_WINDEX_PB),
+	SND_DJM_CTL("Ch2 Output",   750mk2_pb2, 1, SND_DJM_WINDEX_PB),
+	SND_DJM_CTL("Ch3 Output",   750mk2_pb3, 2, SND_DJM_WINDEX_PB)
+};
+
 
 static const struct snd_djm_device snd_djm_devices[] = {
-	SND_DJM_DEVICE(250mk2),
-	SND_DJM_DEVICE(750),
-	SND_DJM_DEVICE(850),
-	SND_DJM_DEVICE(900nxs2)
+	[SND_DJM_250MK2_IDX] = SND_DJM_DEVICE(250mk2),
+	[SND_DJM_750_IDX] = SND_DJM_DEVICE(750),
+	[SND_DJM_850_IDX] = SND_DJM_DEVICE(850),
+	[SND_DJM_900NXS2_IDX] = SND_DJM_DEVICE(900nxs2),
+	[SND_DJM_750MK2_IDX] = SND_DJM_DEVICE(750mk2),
+	[SND_DJM_450_IDX] = SND_DJM_DEVICE(450),
 };
 
 
@@ -3214,8 +3436,14 @@
 		err = snd_soundblaster_e1_switch_create(mixer);
 		break;
 	case USB_ID(0x0bda, 0x4014): /* Dell WD15 dock */
+		err = dell_dock_mixer_create(mixer);
+		if (err < 0)
+			break;
 		err = dell_dock_mixer_init(mixer);
 		break;
+	case USB_ID(0x0bda, 0x402e): /* Dell WD19 dock */
+		err = dell_dock_mixer_create(mixer);
+		break;
 
 	case USB_ID(0x2a39, 0x3fd2): /* RME ADI-2 Pro */
 	case USB_ID(0x2a39, 0x3fd3): /* RME ADI-2 DAC */
@@ -3223,7 +3451,7 @@
 		err = snd_rme_controls_create(mixer);
 		break;
 
-	case USB_ID(0x0194f, 0x010c): /* Presonus Studio 1810c */
+	case USB_ID(0x194f, 0x010c): /* Presonus Studio 1810c */
 		err = snd_sc1810_init_mixer(mixer);
 		break;
 	case USB_ID(0x2a39, 0x3fb0): /* RME Babyface Pro FS */
@@ -3232,9 +3460,15 @@
 	case USB_ID(0x2b73, 0x0017): /* Pioneer DJ DJM-250MK2 */
 		err = snd_djm_controls_create(mixer, SND_DJM_250MK2_IDX);
 		break;
+	case USB_ID(0x2b73, 0x0013): /* Pioneer DJ DJM-450 */
+		err = snd_djm_controls_create(mixer, SND_DJM_450_IDX);
+		break;
 	case USB_ID(0x08e4, 0x017f): /* Pioneer DJ DJM-750 */
 		err = snd_djm_controls_create(mixer, SND_DJM_750_IDX);
 		break;
+	case USB_ID(0x2b73, 0x001b): /* Pioneer DJ DJM-750MK2 */
+		err = snd_djm_controls_create(mixer, SND_DJM_750MK2_IDX);
+		break;
 	case USB_ID(0x08e4, 0x0163): /* Pioneer DJ DJM-850 */
 		err = snd_djm_controls_create(mixer, SND_DJM_850_IDX);
 		break;
@@ -3319,6 +3553,52 @@
 	}
 }
 
+/*
+ * Some Plantronics headsets have control names that don't meet ALSA naming
+ * standards. This function fixes nonstandard source names. By the time
+ * this function is called the control name should look like one of these:
+ * "source names Playback Volume"
+ * "source names Playback Switch"
+ * "source names Capture Volume"
+ * "source names Capture Switch"
+ * If any of the trigger words are found in the name then the name will
+ * be changed to:
+ * "Headset Playback Volume"
+ * "Headset Playback Switch"
+ * "Headset Capture Volume"
+ * "Headset Capture Switch"
+ * depending on the current suffix.
+ */
+static void snd_fix_plt_name(struct snd_usb_audio *chip,
+			     struct snd_ctl_elem_id *id)
+{
+	/* no variant of "Sidetone" should be added to this list */
+	static const char * const trigger[] = {
+		"Earphone", "Microphone", "Receive", "Transmit"
+	};
+	static const char * const suffix[] = {
+		" Playback Volume", " Playback Switch",
+		" Capture Volume", " Capture Switch"
+	};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(trigger); i++)
+		if (strstr(id->name, trigger[i]))
+			goto triggered;
+	usb_audio_dbg(chip, "no change in %s\n", id->name);
+	return;
+
+triggered:
+	for (i = 0; i < ARRAY_SIZE(suffix); i++)
+		if (strstr(id->name, suffix[i])) {
+			usb_audio_dbg(chip, "fixing kctl name %s\n", id->name);
+			snprintf(id->name, sizeof(id->name), "Headset%s",
+				 suffix[i]);
+			return;
+		}
+	usb_audio_dbg(chip, "something wrong in kctl name %s\n", id->name);
+}
+
 void snd_usb_mixer_fu_apply_quirk(struct usb_mixer_interface *mixer,
 				  struct usb_mixer_elem_info *cval, int unitid,
 				  struct snd_kcontrol *kctl)
@@ -3328,12 +3608,18 @@
 		if (unitid == 7 && cval->control == UAC_FU_VOLUME)
 			snd_dragonfly_quirk_db_scale(mixer, cval, kctl);
 		break;
-	/* lowest playback value is muted on C-Media devices */
-	case USB_ID(0x0d8c, 0x000c):
-	case USB_ID(0x0d8c, 0x0014):
+	/* lowest playback value is muted on some devices */
+	case USB_ID(0x0d8c, 0x000c): /* C-Media */
+	case USB_ID(0x0d8c, 0x0014): /* C-Media */
+	case USB_ID(0x19f7, 0x0003): /* RODE NT-USB */
 		if (strstr(kctl->id.name, "Playback"))
 			cval->min_mute = 1;
 		break;
 	}
+
+	/* ALSA-ify some Plantronics headset control names */
+	if (USB_ID_VENDOR(mixer->chip->usb_id) == 0x047f &&
+	    (cval->control == UAC_FU_MUTE || cval->control == UAC_FU_VOLUME))
+		snd_fix_plt_name(mixer->chip, &kctl->id);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/mixer_scarlett_gen2.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/mixer_scarlett_gen2.c
@@ -1213,9 +1213,11 @@
 {
 	__le32 req = cpu_to_le32(SCARLETT2_USB_CONFIG_SAVE);
 
-	scarlett2_usb(mixer, SCARLETT2_USB_DATA_CMD,
-		      &req, sizeof(u32),
-		      NULL, 0);
+	int err = scarlett2_usb(mixer, SCARLETT2_USB_DATA_CMD,
+				&req, sizeof(u32),
+				NULL, 0);
+	if (err < 0)
+		usb_audio_err(mixer->chip, "config save failed: %d\n", err);
 }
 
 /* Delayed work to save config */
@@ -1264,7 +1266,10 @@
 		size = 1;
 		offset = config_item->offset;
 
-		scarlett2_usb_get(mixer, offset, &tmp, 1);
+		err = scarlett2_usb_get(mixer, offset, &tmp, 1);
+		if (err < 0)
+			return err;
+
 		if (value)
 			tmp |= (1 << index);
 		else
@@ -1669,14 +1674,20 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->sync_updated)
-		scarlett2_update_sync(mixer);
+
+	if (private->sync_updated) {
+		err = scarlett2_update_sync(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.enumerated.item[0] = private->sync;
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static const struct snd_kcontrol_new scarlett2_sync_ctl = {
@@ -1759,22 +1770,35 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->vol_updated)
-		scarlett2_update_volumes(mixer);
-	mutex_unlock(&private->data_mutex);
 
+	if (private->vol_updated) {
+		err = scarlett2_update_volumes(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] = private->master_vol;
-	return 0;
+
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int line_out_remap(struct scarlett2_data *private, int index)
 {
 	const struct scarlett2_device_info *info = private->info;
+	const int (*port_count)[SCARLETT2_PORT_DIRNS] = info->port_count;
+	int line_out_count =
+		port_count[SCARLETT2_PORT_TYPE_ANALOGUE][SCARLETT2_PORT_OUT];
 
 	if (!info->line_out_remap_enable)
 		return index;
+
+	if (index >= line_out_count)
+		return index;
+
 	return info->line_out_remap[index];
 }
 
@@ -1785,14 +1809,20 @@
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
 	int index = line_out_remap(private, elem->control);
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->vol_updated)
-		scarlett2_update_volumes(mixer);
-	mutex_unlock(&private->data_mutex);
 
+	if (private->vol_updated) {
+		err = scarlett2_update_volumes(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] = private->vol[index];
-	return 0;
+
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_volume_ctl_put(struct snd_kcontrol *kctl,
@@ -1859,14 +1889,20 @@
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
 	int index = line_out_remap(private, elem->control);
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->vol_updated)
-		scarlett2_update_volumes(mixer);
-	mutex_unlock(&private->data_mutex);
 
+	if (private->vol_updated) {
+		err = scarlett2_update_volumes(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] = private->mute_switch[index];
-	return 0;
+
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_mute_ctl_put(struct snd_kcontrol *kctl,
@@ -2112,14 +2148,20 @@
 	const struct scarlett2_device_info *info = private->info;
 
 	int index = elem->control + info->level_input_first;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->input_other_updated)
-		scarlett2_update_input_other(mixer);
+
+	if (private->input_other_updated) {
+		err = scarlett2_update_input_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.enumerated.item[0] = private->level_switch[index];
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_level_enum_ctl_put(struct snd_kcontrol *kctl,
@@ -2170,15 +2212,21 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->input_other_updated)
-		scarlett2_update_input_other(mixer);
+
+	if (private->input_other_updated) {
+		err = scarlett2_update_input_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] =
 		private->pad_switch[elem->control];
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_pad_ctl_put(struct snd_kcontrol *kctl,
@@ -2228,14 +2276,20 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->input_other_updated)
-		scarlett2_update_input_other(mixer);
+
+	if (private->input_other_updated) {
+		err = scarlett2_update_input_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] = private->air_switch[elem->control];
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_air_ctl_put(struct snd_kcontrol *kctl,
@@ -2285,15 +2339,21 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->input_other_updated)
-		scarlett2_update_input_other(mixer);
+
+	if (private->input_other_updated) {
+		err = scarlett2_update_input_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] =
 		private->phantom_switch[elem->control];
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_phantom_ctl_put(struct snd_kcontrol *kctl,
@@ -2465,14 +2525,20 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = elem->head.mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->monitor_other_updated)
-		scarlett2_update_monitor_other(mixer);
+
+	if (private->monitor_other_updated) {
+		err = scarlett2_update_monitor_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.enumerated.item[0] = private->direct_monitor_switch;
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_direct_monitor_ctl_put(
@@ -2572,14 +2638,20 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->monitor_other_updated)
-		scarlett2_update_monitor_other(mixer);
+
+	if (private->monitor_other_updated) {
+		err = scarlett2_update_monitor_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.enumerated.item[0] = private->speaker_switching_switch;
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 /* when speaker switching gets enabled, switch the main/alt speakers
@@ -2727,14 +2799,20 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->monitor_other_updated)
-		scarlett2_update_monitor_other(mixer);
+
+	if (private->monitor_other_updated) {
+		err = scarlett2_update_monitor_other(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.enumerated.item[0] = private->talkback_switch;
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_talkback_enum_ctl_put(
@@ -2882,14 +2960,20 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->vol_updated)
-		scarlett2_update_volumes(mixer);
-	mutex_unlock(&private->data_mutex);
 
+	if (private->vol_updated) {
+		err = scarlett2_update_volumes(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.integer.value[0] = private->dim_mute[elem->control];
-	return 0;
+
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_dim_mute_ctl_put(struct snd_kcontrol *kctl,
@@ -3153,7 +3237,8 @@
 	mutex_lock(&private->data_mutex);
 
 	oval = private->mix[index];
-	val = ucontrol->value.integer.value[0];
+	val = clamp(ucontrol->value.integer.value[0],
+		    0L, (long)SCARLETT2_MIXER_MAX_VALUE);
 	num_mixer_in = port_count[SCARLETT2_PORT_TYPE_MIX][SCARLETT2_PORT_OUT];
 	mix_num = index / num_mixer_in;
 
@@ -3259,22 +3344,21 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
-	const struct scarlett2_device_info *info = private->info;
-	const int (*port_count)[SCARLETT2_PORT_DIRNS] = info->port_count;
-	int line_out_count =
-		port_count[SCARLETT2_PORT_TYPE_ANALOGUE][SCARLETT2_PORT_OUT];
-	int index = elem->control;
-
-	if (index < line_out_count)
-		index = line_out_remap(private, index);
+	int index = line_out_remap(private, elem->control);
+	int err = 0;
 
 	mutex_lock(&private->data_mutex);
-	if (private->mux_updated)
-		scarlett2_usb_get_mux(mixer);
+
+	if (private->mux_updated) {
+		err = scarlett2_usb_get_mux(mixer);
+		if (err < 0)
+			goto unlock;
+	}
 	ucontrol->value.enumerated.item[0] = private->mux[index];
-	mutex_unlock(&private->data_mutex);
 
-	return 0;
+unlock:
+	mutex_unlock(&private->data_mutex);
+	return err;
 }
 
 static int scarlett2_mux_src_enum_ctl_put(struct snd_kcontrol *kctl,
@@ -3283,16 +3367,9 @@
 	struct usb_mixer_elem_info *elem = kctl->private_data;
 	struct usb_mixer_interface *mixer = elem->head.mixer;
 	struct scarlett2_data *private = mixer->private_data;
-	const struct scarlett2_device_info *info = private->info;
-	const int (*port_count)[SCARLETT2_PORT_DIRNS] = info->port_count;
-	int line_out_count =
-		port_count[SCARLETT2_PORT_TYPE_ANALOGUE][SCARLETT2_PORT_OUT];
-	int index = elem->control;
+	int index = line_out_remap(private, elem->control);
 	int oval, val, err = 0;
 
-	if (index < line_out_count)
-		index = line_out_remap(private, index);
-
 	mutex_lock(&private->data_mutex);
 
 	oval = private->mux[index];
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/mixer_us16x08.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/mixer_us16x08.c
@@ -687,7 +687,7 @@
 	struct usb_mixer_elem_info *elem = kcontrol->private_data;
 	struct snd_usb_audio *chip = elem->head.mixer->chip;
 	struct snd_us16x08_meter_store *store = elem->private_data;
-	u8 meter_urb[64];
+	u8 meter_urb[64] = {0};
 
 	switch (kcontrol->private_value) {
 	case 0: {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/pcm.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/pcm.c
@@ -157,6 +157,34 @@
 			   true, subs);
 }
 
+bool snd_usb_pcm_has_fixed_rate(struct snd_usb_substream *subs)
+{
+	const struct audioformat *fp;
+	struct snd_usb_audio *chip;
+	int rate = -1;
+
+	if (!subs)
+		return false;
+	chip = subs->stream->chip;
+	if (!(chip->quirk_flags & QUIRK_FLAG_FIXED_RATE))
+		return false;
+	list_for_each_entry(fp, &subs->fmt_list, list) {
+		if (fp->rates & SNDRV_PCM_RATE_CONTINUOUS)
+			return false;
+		if (fp->nr_rates < 1)
+			continue;
+		if (fp->nr_rates > 1)
+			return false;
+		if (rate < 0) {
+			rate = fp->rate_table[0];
+			continue;
+		}
+		if (rate != fp->rate_table[0])
+			return false;
+	}
+	return true;
+}
+
 static int init_pitch_v1(struct snd_usb_audio *chip, int ep)
 {
 	struct usb_device *dev = chip->dev;
@@ -219,16 +247,16 @@
 	return 0;
 }
 
-static bool stop_endpoints(struct snd_usb_substream *subs)
+static bool stop_endpoints(struct snd_usb_substream *subs, bool keep_pending)
 {
 	bool stopped = 0;
 
 	if (test_and_clear_bit(SUBSTREAM_FLAG_SYNC_EP_STARTED, &subs->flags)) {
-		snd_usb_endpoint_stop(subs->sync_endpoint);
+		snd_usb_endpoint_stop(subs->sync_endpoint, keep_pending);
 		stopped = true;
 	}
 	if (test_and_clear_bit(SUBSTREAM_FLAG_DATA_EP_STARTED, &subs->flags)) {
-		snd_usb_endpoint_stop(subs->data_endpoint);
+		snd_usb_endpoint_stop(subs->data_endpoint, keep_pending);
 		stopped = true;
 	}
 	return stopped;
@@ -261,7 +289,7 @@
 	return 0;
 
  error:
-	stop_endpoints(subs);
+	stop_endpoints(subs, false);
 	return err;
 }
 
@@ -291,6 +319,9 @@
 	bool is_playback;
 	int err;
 
+	if (fmt->sync_ep)
+		return 0; /* already set up */
+
 	alts = snd_usb_get_host_interface(chip, fmt->iface, fmt->altsetting);
 	if (!alts)
 		return 0;
@@ -304,7 +335,7 @@
 	 * Generic sync EP handling
 	 */
 
-	if (altsd->bNumEndpoints < 2)
+	if (fmt->ep_idx > 0 || altsd->bNumEndpoints < 2)
 		return 0;
 
 	is_playback = !(get_endpoint(alts, 0)->bEndpointAddress & USB_DIR_IN);
@@ -430,30 +461,6 @@
 	}
 }
 
-static int configure_endpoints(struct snd_usb_audio *chip,
-			       struct snd_usb_substream *subs)
-{
-	int err;
-
-	if (subs->data_endpoint->need_setup) {
-		/* stop any running stream beforehand */
-		if (stop_endpoints(subs))
-			sync_pending_stops(subs);
-		err = snd_usb_endpoint_configure(chip, subs->data_endpoint);
-		if (err < 0)
-			return err;
-		snd_usb_set_format_quirk(subs, subs->cur_audiofmt);
-	}
-
-	if (subs->sync_endpoint) {
-		err = snd_usb_endpoint_configure(chip, subs->sync_endpoint);
-		if (err < 0)
-			return err;
-	}
-
-	return 0;
-}
-
 /*
  * hw_params callback
  *
@@ -471,12 +478,14 @@
 	struct snd_usb_audio *chip = subs->stream->chip;
 	const struct audioformat *fmt;
 	const struct audioformat *sync_fmt;
+	bool fixed_rate, sync_fixed_rate;
 	int ret;
 
 	ret = snd_media_start_pipeline(subs);
 	if (ret)
 		return ret;
 
+	fixed_rate = snd_usb_pcm_has_fixed_rate(subs);
 	fmt = find_substream_format(subs, hw_params);
 	if (!fmt) {
 		usb_audio_dbg(chip,
@@ -490,7 +499,8 @@
 	if (fmt->implicit_fb) {
 		sync_fmt = snd_usb_find_implicit_fb_sync_format(chip, fmt,
 								hw_params,
-								!substream->stream);
+								!substream->stream,
+								&sync_fixed_rate);
 		if (!sync_fmt) {
 			usb_audio_dbg(chip,
 				      "cannot find sync format: ep=0x%x, iface=%d:%d, format=%s, rate=%d, channels=%d\n",
@@ -503,6 +513,7 @@
 		}
 	} else {
 		sync_fmt = fmt;
+		sync_fixed_rate = fixed_rate;
 	}
 
 	ret = snd_usb_lock_shutdown(chip);
@@ -517,10 +528,12 @@
 		if (snd_usb_endpoint_compatible(chip, subs->data_endpoint,
 						fmt, hw_params))
 			goto unlock;
+		if (stop_endpoints(subs, false))
+			sync_pending_stops(subs);
 		close_endpoints(chip, subs);
 	}
 
-	subs->data_endpoint = snd_usb_endpoint_open(chip, fmt, hw_params, false);
+	subs->data_endpoint = snd_usb_endpoint_open(chip, fmt, hw_params, false, fixed_rate);
 	if (!subs->data_endpoint) {
 		ret = -EINVAL;
 		goto unlock;
@@ -529,7 +542,8 @@
 	if (fmt->sync_ep) {
 		subs->sync_endpoint = snd_usb_endpoint_open(chip, sync_fmt,
 							    hw_params,
-							    fmt == sync_fmt);
+							    fmt == sync_fmt,
+							    sync_fixed_rate);
 		if (!subs->sync_endpoint) {
 			ret = -EINVAL;
 			goto unlock;
@@ -543,7 +557,16 @@
 	subs->cur_audiofmt = fmt;
 	mutex_unlock(&chip->mutex);
 
-	ret = configure_endpoints(chip, subs);
+	if (!subs->data_endpoint->need_setup)
+		goto unlock;
+
+	if (subs->sync_endpoint) {
+		ret = snd_usb_endpoint_set_params(chip, subs->sync_endpoint);
+		if (ret < 0)
+			goto unlock;
+	}
+
+	ret = snd_usb_endpoint_set_params(chip, subs->data_endpoint);
 
  unlock:
 	if (ret < 0)
@@ -572,7 +595,7 @@
 	subs->cur_audiofmt = NULL;
 	mutex_unlock(&chip->mutex);
 	if (!snd_usb_lock_shutdown(chip)) {
-		if (stop_endpoints(subs))
+		if (stop_endpoints(subs, false))
 			sync_pending_stops(subs);
 		close_endpoints(chip, subs);
 		snd_usb_unlock_shutdown(chip);
@@ -581,6 +604,31 @@
 	return 0;
 }
 
+/* free-wheeling mode? (e.g. dmix) */
+static int in_free_wheeling_mode(struct snd_pcm_runtime *runtime)
+{
+	return runtime->stop_threshold > runtime->buffer_size;
+}
+
+/* check whether early start is needed for playback stream */
+static int lowlatency_playback_available(struct snd_pcm_runtime *runtime,
+					 struct snd_usb_substream *subs)
+{
+	struct snd_usb_audio *chip = subs->stream->chip;
+
+	if (subs->direction == SNDRV_PCM_STREAM_CAPTURE)
+		return false;
+	/* disabled via module option? */
+	if (!chip->lowlatency)
+		return false;
+	if (in_free_wheeling_mode(runtime))
+		return false;
+	/* implicit feedback mode has own operation mode */
+	if (snd_usb_endpoint_implicit_feedback_sink(subs->data_endpoint))
+		return false;
+	return true;
+}
+
 /*
  * prepare callback
  *
@@ -601,9 +649,18 @@
 		goto unlock;
 	}
 
-	ret = configure_endpoints(chip, subs);
+	if (subs->sync_endpoint) {
+		ret = snd_usb_endpoint_prepare(chip, subs->sync_endpoint);
+		if (ret < 0)
+			goto unlock;
+	}
+
+	ret = snd_usb_endpoint_prepare(chip, subs->data_endpoint);
 	if (ret < 0)
 		goto unlock;
+	else if (ret > 0)
+		snd_usb_set_format_quirk(subs, subs->cur_audiofmt);
+	ret = 0;
 
 	/* reset the pointer */
 	subs->buffer_bytes = frames_to_bytes(runtime, runtime->buffer_size);
@@ -614,13 +671,9 @@
 	subs->period_elapsed_pending = 0;
 	runtime->delay = 0;
 
-	/* check whether early start is needed for playback stream */
-	subs->early_playback_start =
-		subs->direction == SNDRV_PCM_STREAM_PLAYBACK &&
-		(!chip->lowlatency ||
-		 (subs->data_endpoint->nominal_queue_size >= subs->buffer_bytes));
-
-	if (subs->early_playback_start)
+	subs->lowlatency_playback = lowlatency_playback_available(runtime, subs);
+	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
+	    !subs->lowlatency_playback)
 		ret = start_endpoints(subs);
 
  unlock:
@@ -648,9 +701,9 @@
 				SNDRV_PCM_INFO_PAUSE,
 	.channels_min =		1,
 	.channels_max =		256,
-	.buffer_bytes_max =	1024 * 1024,
+	.buffer_bytes_max =	INT_MAX, /* limited by BUFFER_TIME later */
 	.period_bytes_min =	64,
-	.period_bytes_max =	512 * 1024,
+	.period_bytes_max =	INT_MAX, /* limited by PERIOD_TIME later */
 	.periods_min =		2,
 	.periods_max =		1024,
 };
@@ -734,6 +787,7 @@
 			struct snd_pcm_hw_rule *rule)
 {
 	struct snd_usb_substream *subs = rule->private;
+	struct snd_usb_audio *chip = subs->stream->chip;
 	const struct audioformat *fp;
 	struct snd_interval *it = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE);
 	unsigned int rmin, rmax, r;
@@ -745,6 +799,14 @@
 	list_for_each_entry(fp, &subs->fmt_list, list) {
 		if (!hw_check_valid_format(subs, params, fp))
 			continue;
+		r = snd_usb_endpoint_get_clock_rate(chip, fp->clock);
+		if (r > 0) {
+			if (!snd_interval_test(it, r))
+				continue;
+			rmin = min(rmin, r);
+			rmax = max(rmax, r);
+			continue;
+		}
 		if (fp->rate_table && fp->nr_rates) {
 			for (i = 0; i < fp->nr_rates; i++) {
 				r = fp->rate_table[i];
@@ -869,8 +931,13 @@
 			continue;
 		/* for the implicit fb, check the sync ep as well */
 		ep = snd_usb_get_endpoint(chip, fp->sync_ep);
-		if (ep && ep->cur_audiofmt)
-			return ep;
+		if (ep && ep->cur_audiofmt) {
+			/* ditto, if the sync (data) ep is used by others,
+			 * this stream is restricted by the sync ep
+			 */
+			if (ep != subs->sync_endpoint || ep->opened > 1)
+				return ep;
+		}
 	}
 	return NULL;
 }
@@ -1034,6 +1101,18 @@
 			return err;
 	}
 
+	/* set max period and buffer sizes for 1 and 2 seconds, respectively */
+	err = snd_pcm_hw_constraint_minmax(runtime,
+					   SNDRV_PCM_HW_PARAM_PERIOD_TIME,
+					   0, 1000000);
+	if (err < 0)
+		return err;
+	err = snd_pcm_hw_constraint_minmax(runtime,
+					   SNDRV_PCM_HW_PARAM_BUFFER_TIME,
+					   0, 2000000);
+	if (err < 0)
+		return err;
+
 	/* additional hw constraints for implicit fb */
 	err = snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT,
 				  hw_rule_format_implicit_fb, subs,
@@ -1068,6 +1147,10 @@
 	int ret;
 
 	runtime->hw = snd_usb_hardware;
+	/* need an explicit sync to catch applptr update in low-latency mode */
+	if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
+	    as->chip->lowlatency)
+		runtime->hw.info |= SNDRV_PCM_INFO_SYNC_APPLPTR;
 	runtime->private_data = subs;
 	subs->pcm_substream = substream;
 	/* runtime PM is also done there */
@@ -1320,44 +1403,66 @@
 	return bytes;
 }
 
-static void prepare_playback_urb(struct snd_usb_substream *subs,
-				 struct urb *urb)
+static int prepare_playback_urb(struct snd_usb_substream *subs,
+				struct urb *urb,
+				bool in_stream_lock)
 {
 	struct snd_pcm_runtime *runtime = subs->pcm_substream->runtime;
 	struct snd_usb_endpoint *ep = subs->data_endpoint;
 	struct snd_urb_ctx *ctx = urb->context;
-	unsigned int counts, frames, bytes;
+	unsigned int frames, bytes;
+	int counts;
+	unsigned int transfer_done, frame_limit, avail = 0;
 	int i, stride, period_elapsed = 0;
 	unsigned long flags;
+	int err = 0;
 
 	stride = ep->stride;
 
 	frames = 0;
 	ctx->queued = 0;
 	urb->number_of_packets = 0;
+
 	spin_lock_irqsave(&subs->lock, flags);
-	subs->frame_limit += ep->max_urb_frames;
+	frame_limit = subs->frame_limit + ep->max_urb_frames;
+	transfer_done = subs->transfer_done;
+
+	if (subs->lowlatency_playback &&
+	    runtime->status->state != SNDRV_PCM_STATE_DRAINING) {
+		unsigned int hwptr = subs->hwptr_done / stride;
+
+		/* calculate the byte offset-in-buffer of the appl_ptr */
+		avail = (runtime->control->appl_ptr - runtime->hw_ptr_base)
+			% runtime->buffer_size;
+		if (avail <= hwptr)
+			avail += runtime->buffer_size;
+		avail -= hwptr;
+	}
+
 	for (i = 0; i < ctx->packets; i++) {
-		counts = snd_usb_endpoint_next_packet_size(ep, ctx, i);
+		counts = snd_usb_endpoint_next_packet_size(ep, ctx, i, avail);
+		if (counts < 0)
+			break;
 		/* set up descriptor */
 		urb->iso_frame_desc[i].offset = frames * stride;
 		urb->iso_frame_desc[i].length = counts * stride;
 		frames += counts;
+		avail -= counts;
 		urb->number_of_packets++;
-		subs->transfer_done += counts;
-		if (subs->transfer_done >= runtime->period_size) {
-			subs->transfer_done -= runtime->period_size;
-			subs->frame_limit = 0;
+		transfer_done += counts;
+		if (transfer_done >= runtime->period_size) {
+			transfer_done -= runtime->period_size;
+			frame_limit = 0;
 			period_elapsed = 1;
 			if (subs->fmt_type == UAC_FORMAT_TYPE_II) {
-				if (subs->transfer_done > 0) {
+				if (transfer_done > 0) {
 					/* FIXME: fill-max mode is not
 					 * supported yet */
-					frames -= subs->transfer_done;
-					counts -= subs->transfer_done;
+					frames -= transfer_done;
+					counts -= transfer_done;
 					urb->iso_frame_desc[i].length =
 						counts * stride;
-					subs->transfer_done = 0;
+					transfer_done = 0;
 				}
 				i++;
 				if (i < ctx->packets) {
@@ -1371,13 +1476,19 @@
 			}
 		}
 		/* finish at the period boundary or after enough frames */
-		if ((period_elapsed ||
-				subs->transfer_done >= subs->frame_limit) &&
+		if ((period_elapsed || transfer_done >= frame_limit) &&
 		    !snd_usb_endpoint_implicit_feedback_sink(ep))
 			break;
 	}
-	bytes = frames * stride;
 
+	if (!frames) {
+		err = -EAGAIN;
+		goto unlock;
+	}
+
+	bytes = frames * stride;
+	subs->transfer_done = transfer_done;
+	subs->frame_limit = frame_limit;
 	if (unlikely(ep->cur_format == SNDRV_PCM_FORMAT_DSD_U16_LE &&
 		     subs->cur_audiofmt->dsd_dop)) {
 		fill_playback_urb_dsd_dop(subs, urb, bytes);
@@ -1403,14 +1514,23 @@
 		subs->trigger_tstamp_pending_update = false;
 	}
 
-	if (period_elapsed && !subs->running && !subs->early_playback_start) {
+	if (period_elapsed && !subs->running && subs->lowlatency_playback) {
 		subs->period_elapsed_pending = 1;
 		period_elapsed = 0;
 	}
+
+ unlock:
 	spin_unlock_irqrestore(&subs->lock, flags);
+	if (err < 0)
+		return err;
 	urb->transfer_buffer_length = bytes;
-	if (period_elapsed)
-		snd_pcm_period_elapsed(subs->pcm_substream);
+	if (period_elapsed) {
+		if (in_stream_lock)
+			snd_pcm_period_elapsed_under_stream_lock(subs->pcm_substream);
+		else
+			snd_pcm_period_elapsed(subs->pcm_substream);
+	}
+	return 0;
 }
 
 /*
@@ -1442,6 +1562,27 @@
 		snd_pcm_period_elapsed(subs->pcm_substream);
 }
 
+/* PCM ack callback for the playback stream;
+ * this plays a role only when the stream is running in low-latency mode.
+ */
+static int snd_usb_pcm_playback_ack(struct snd_pcm_substream *substream)
+{
+	struct snd_usb_substream *subs = substream->runtime->private_data;
+	struct snd_usb_endpoint *ep;
+
+	if (!subs->lowlatency_playback || !subs->running)
+		return 0;
+	ep = subs->data_endpoint;
+	if (!ep)
+		return 0;
+	/* When no more in-flight URBs available, try to process the pending
+	 * outputs here
+	 */
+	if (!ep->active_mask)
+		return snd_usb_queue_pending_output_urbs(ep, true);
+	return 0;
+}
+
 static int snd_usb_substream_playback_trigger(struct snd_pcm_substream *substream,
 					      int cmd)
 {
@@ -1457,8 +1598,10 @@
 					      prepare_playback_urb,
 					      retire_playback_urb,
 					      subs);
-		if (!subs->early_playback_start &&
+		if (subs->lowlatency_playback &&
 		    cmd == SNDRV_PCM_TRIGGER_START) {
+			if (in_free_wheeling_mode(substream->runtime))
+				subs->lowlatency_playback = false;
 			err = start_endpoints(subs);
 			if (err < 0) {
 				snd_usb_endpoint_set_callback(subs->data_endpoint,
@@ -1473,7 +1616,7 @@
 		return 0;
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_STOP:
-		stop_endpoints(subs);
+		stop_endpoints(subs, substream->runtime->status->state == SNDRV_PCM_STATE_DRAINING);
 		snd_usb_endpoint_set_callback(subs->data_endpoint,
 					      NULL, NULL, NULL);
 		subs->running = 0;
@@ -1521,7 +1664,7 @@
 		return 0;
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_STOP:
-		stop_endpoints(subs);
+		stop_endpoints(subs, false);
 		fallthrough;
 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
 		snd_usb_endpoint_set_callback(subs->data_endpoint,
@@ -1545,6 +1688,7 @@
 	.trigger =	snd_usb_substream_playback_trigger,
 	.sync_stop =	snd_usb_pcm_sync_stop,
 	.pointer =	snd_usb_pcm_pointer,
+	.ack =		snd_usb_pcm_playback_ack,
 };
 
 static const struct snd_pcm_ops snd_usb_capture_ops = {
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/pcm.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/pcm.h
@@ -6,6 +6,8 @@
 int snd_usb_pcm_suspend(struct snd_usb_stream *as);
 int snd_usb_pcm_resume(struct snd_usb_stream *as);
 
+bool snd_usb_pcm_has_fixed_rate(struct snd_usb_substream *as);
+
 int snd_usb_init_pitch(struct snd_usb_audio *chip,
 		       const struct audioformat *fmt);
 void snd_usb_preallocate_buffer(struct snd_usb_substream *subs);
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/quirks-table.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/quirks-table.h
@@ -35,6 +35,83 @@
 	.bInterfaceClass = USB_CLASS_AUDIO, \
 	.bInterfaceSubClass = USB_SUBCLASS_AUDIOCONTROL
 
+/* Quirk .driver_info, followed by the definition of the quirk entry;
+ * put like QUIRK_DRIVER_INFO { ... } in each entry of the quirk table
+ */
+#define QUIRK_DRIVER_INFO \
+	.driver_info = (unsigned long)&(const struct snd_usb_audio_quirk)
+
+/*
+ * Macros for quirk data entries
+ */
+
+/* Quirk data entry for ignoring the interface */
+#define QUIRK_DATA_IGNORE(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_IGNORE_INTERFACE
+/* Quirk data entry for a standard audio interface */
+#define QUIRK_DATA_STANDARD_AUDIO(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_AUDIO_STANDARD_INTERFACE
+/* Quirk data entry for a standard MIDI interface */
+#define QUIRK_DATA_STANDARD_MIDI(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_MIDI_STANDARD_INTERFACE
+/* Quirk data entry for a standard mixer interface */
+#define QUIRK_DATA_STANDARD_MIXER(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_AUDIO_STANDARD_MIXER
+
+/* Quirk data entry for Yamaha MIDI */
+#define QUIRK_DATA_MIDI_YAMAHA(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_MIDI_YAMAHA
+/* Quirk data entry for Edirol UAxx */
+#define QUIRK_DATA_EDIROL_UAXX(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_AUDIO_EDIROL_UAXX
+/* Quirk data entry for raw bytes interface */
+#define QUIRK_DATA_RAW_BYTES(_ifno) \
+	.ifnum = (_ifno), .type = QUIRK_MIDI_RAW_BYTES
+
+/* Quirk composite array terminator */
+#define QUIRK_COMPOSITE_END	{ .ifnum = -1 }
+
+/* Quirk data entry for composite quirks;
+ * followed by the quirk array that is terminated with QUIRK_COMPOSITE_END
+ * e.g. QUIRK_DATA_COMPOSITE { { quirk1 }, { quirk2 },..., QUIRK_COMPOSITE_END }
+ */
+#define QUIRK_DATA_COMPOSITE \
+	.ifnum = QUIRK_ANY_INTERFACE, \
+	.type = QUIRK_COMPOSITE, \
+	.data = &(const struct snd_usb_audio_quirk[])
+
+/* Quirk data entry for a fixed audio endpoint;
+ * followed by audioformat definition
+ * e.g. QUIRK_DATA_AUDIOFORMAT(n) { .formats = xxx, ... }
+ */
+#define QUIRK_DATA_AUDIOFORMAT(_ifno)	    \
+	.ifnum = (_ifno),		    \
+	.type = QUIRK_AUDIO_FIXED_ENDPOINT, \
+	.data = &(const struct audioformat)
+
+/* Quirk data entry for a fixed MIDI endpoint;
+ * followed by snd_usb_midi_endpoint_info definition
+ * e.g. QUIRK_DATA_MIDI_FIXED_ENDPOINT(n) { .out_cables = x, .in_cables = y }
+ */
+#define QUIRK_DATA_MIDI_FIXED_ENDPOINT(_ifno) \
+	.ifnum = (_ifno),		      \
+	.type = QUIRK_MIDI_FIXED_ENDPOINT,    \
+	.data = &(const struct snd_usb_midi_endpoint_info)
+/* Quirk data entry for a MIDIMAN MIDI endpoint */
+#define QUIRK_DATA_MIDI_MIDIMAN(_ifno) \
+	.ifnum = (_ifno),	       \
+	.type = QUIRK_MIDI_MIDIMAN,    \
+	.data = &(const struct snd_usb_midi_endpoint_info)
+/* Quirk data entry for a EMAGIC MIDI endpoint */
+#define QUIRK_DATA_MIDI_EMAGIC(_ifno) \
+	.ifnum = (_ifno),	      \
+	.type = QUIRK_MIDI_EMAGIC,    \
+	.data = &(const struct snd_usb_midi_endpoint_info)
+
+/*
+ * Here we go... the quirk table definition begins:
+ */
+
 /* FTDI devices */
 {
 	USB_DEVICE(0x0403, 0xb8d8),
@@ -76,6 +153,8 @@
 { USB_DEVICE_VENDOR_SPEC(0x041e, 0x3f0a) },
 /* E-Mu 0204 USB */
 { USB_DEVICE_VENDOR_SPEC(0x041e, 0x3f19) },
+/* Ktmicro Usb_audio device */
+{ USB_DEVICE_VENDOR_SPEC(0x31b2, 0x0011) },
 
 /*
  * Creative Technology, Ltd Live! Cam Sync HD [VF0770]
@@ -84,7 +163,7 @@
  * combination.
  */
 {
-	USB_DEVICE(0x041e, 0x4095),
+	USB_AUDIO_DEVICE(0x041e, 0x4095),
 	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
 		.ifnum = QUIRK_ANY_INTERFACE,
 		.type = QUIRK_COMPOSITE,
@@ -405,6 +484,19 @@
 		}
 	}
 },
+{
+	USB_DEVICE(0x0499, 0x1718),
+	QUIRK_DRIVER_INFO {
+		/* .vendor_name = "Yamaha", */
+		/* .product_name = "P-125", */
+		QUIRK_DATA_COMPOSITE {
+			{ QUIRK_DATA_STANDARD_AUDIO(1) },
+			{ QUIRK_DATA_STANDARD_AUDIO(2) },
+			{ QUIRK_DATA_MIDI_YAMAHA(3) },
+			QUIRK_COMPOSITE_END
+		}
+	}
+},
 YAMAHA_DEVICE(0x2000, "DGP-7"),
 YAMAHA_DEVICE(0x2001, "DGP-5"),
 YAMAHA_DEVICE(0x2002, NULL),
@@ -2050,6 +2142,10 @@
 	}
 },
 {
+	/* M-Audio Micro */
+	USB_DEVICE_VENDOR_SPEC(0x0763, 0x201a),
+},
+{
 	USB_DEVICE_VENDOR_SPEC(0x0763, 0x2030),
 	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
 		/* .vendor_name = "M-Audio", */
@@ -2588,6 +2684,10 @@
 	}
 },
 
+/* Stanton ScratchAmp */
+{ USB_DEVICE(0x103d, 0x0100) },
+{ USB_DEVICE(0x103d, 0x0101) },
+
 /* Novation EMS devices */
 {
 	USB_DEVICE_VENDOR_SPEC(0x1235, 0x0001),
@@ -2658,7 +2758,12 @@
 					.nr_rates = 2,
 					.rate_table = (unsigned int[]) {
 						44100, 48000
-					}
+					},
+					.sync_ep = 0x82,
+					.sync_iface = 0,
+					.sync_altsetting = 1,
+					.sync_ep_idx = 1,
+					.implicit_fb = 1,
 				}
 			},
 			{
@@ -2672,6 +2777,7 @@
 					.altset_idx = 1,
 					.attributes = 0,
 					.endpoint = 0x82,
+					.ep_idx = 1,
 					.ep_attr = USB_ENDPOINT_XFER_ISOC,
 					.datainterval = 1,
 					.maxpacksize = 0x0126,
@@ -2875,6 +2981,7 @@
 					.altset_idx = 1,
 					.attributes = 0x4,
 					.endpoint = 0x81,
+					.ep_idx = 1,
 					.ep_attr = USB_ENDPOINT_XFER_ISOC |
 						USB_ENDPOINT_SYNC_ASYNC,
 					.maxpacksize = 0x130,
@@ -3235,6 +3342,15 @@
 	}
 },
 
+/* Rane SL-1 */
+{
+	USB_DEVICE(0x13e5, 0x0001),
+	.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_AUDIO_STANDARD_INTERFACE
+        }
+},
+
 /* disabled due to regression for other devices;
  * see https://bugzilla.kernel.org/show_bug.cgi?id=199905
  */
@@ -3382,6 +3498,7 @@
 					.altset_idx = 1,
 					.attributes = 0,
 					.endpoint = 0x03,
+					.ep_idx = 1,
 					.rates = SNDRV_PCM_RATE_96000,
 					.ep_attr = USB_ENDPOINT_XFER_ISOC |
 						   USB_ENDPOINT_SYNC_ASYNC,
@@ -3785,6 +3902,112 @@
 	}
 },
 
+{
+	/*
+	 * PIONEER DJ DDJ-800
+	 * PCM is 6 channels out, 6 channels in @ 44.1 fixed
+	 * The Feedback for the output is the input
+	 */
+	USB_DEVICE_VENDOR_SPEC(0x2b73, 0x0029),
+		.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = (const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S24_3LE,
+					.channels = 6,
+					.iface = 0,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x01,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC|
+						USB_ENDPOINT_SYNC_ASYNC,
+					.rates = SNDRV_PCM_RATE_44100,
+					.rate_min = 44100,
+					.rate_max = 44100,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 44100 }
+				}
+			},
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S24_3LE,
+					.channels = 6,
+					.iface = 0,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x82,
+					.ep_idx = 1,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC|
+						USB_ENDPOINT_SYNC_ASYNC|
+					USB_ENDPOINT_USAGE_IMPLICIT_FB,
+					.rates = SNDRV_PCM_RATE_44100,
+					.rate_min = 44100,
+					.rate_max = 44100,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 44100 }
+				}
+			},
+			{
+				.ifnum = -1
+			}
+		}
+	}
+},
+
+/*
+ * MacroSilicon MS2100/MS2106 based AV capture cards
+ *
+ * These claim 96kHz 1ch in the descriptors, but are actually 48kHz 2ch.
+ * They also need QUIRK_FLAG_ALIGN_TRANSFER, which makes one wonder if
+ * they pretend to be 96kHz mono as a workaround for stereo being broken
+ * by that...
+ *
+ * They also have an issue with initial stream alignment that causes the
+ * channels to be swapped and out of phase, which is dealt with in quirks.c.
+ */
+{
+	USB_AUDIO_DEVICE(0x534d, 0x0021),
+	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.vendor_name = "MacroSilicon",
+		.product_name = "MS210x",
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = &(const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 2,
+				.type = QUIRK_AUDIO_STANDARD_MIXER,
+			},
+			{
+				.ifnum = 3,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S16_LE,
+					.channels = 2,
+					.iface = 3,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.attributes = 0,
+					.endpoint = 0x82,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						USB_ENDPOINT_SYNC_ASYNC,
+					.rates = SNDRV_PCM_RATE_CONTINUOUS,
+					.rate_min = 48000,
+					.rate_max = 48000,
+				}
+			},
+			{
+				.ifnum = -1
+			}
+		}
+	}
+},
+
 /*
  * MacroSilicon MS2109 based HDMI capture cards
  *
@@ -3894,6 +4117,64 @@
 },
 {
 	/*
+	 * Pioneer DJ DJM-750MK2
+	 * 10 channels playback & 12 channels capture @ 48kHz S24LE
+	 */
+	USB_DEVICE_VENDOR_SPEC(0x2b73, 0x001b),
+	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = (const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S24_3LE,
+					.channels = 10,
+					.iface = 0,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x01,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC|
+					    USB_ENDPOINT_SYNC_ASYNC,
+					.rates = SNDRV_PCM_RATE_48000,
+					.rate_min = 48000,
+					.rate_max = 48000,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) {
+						48000
+					}
+				}
+			},
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S24_3LE,
+					.channels = 12,
+					.iface = 0,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x82,
+					.ep_idx = 1,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC|
+						USB_ENDPOINT_SYNC_ASYNC|
+						USB_ENDPOINT_USAGE_IMPLICIT_FB,
+					.rates = SNDRV_PCM_RATE_48000,
+					.rate_min = 48000,
+					.rate_max = 48000,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 48000 }
+				}
+			},
+			{
+				.ifnum = -1
+			}
+		}
+	}
+},
+{
+	/*
 	 * Pioneer DJ DJM-850
 	 * 8 channels playback and 8 channels capture @ 44.1/48/96kHz S24LE
 	 * Playback on EP 0x05
@@ -4040,6 +4321,235 @@
 			},
 			{
 				.ifnum = -1
+			}
+		}
+	}
+},
+{
+	/*
+	 * Fiero SC-01 (firmware v1.0.0 @ 48 kHz)
+	 */
+	USB_DEVICE(0x2b53, 0x0023),
+	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.vendor_name = "Fiero",
+		.product_name = "SC-01",
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = &(const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_STANDARD_INTERFACE
+			},
+			/* Playback */
+			{
+				.ifnum = 1,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S32_LE,
+					.channels = 2,
+					.fmt_bits = 24,
+					.iface = 1,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x01,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						   USB_ENDPOINT_SYNC_ASYNC,
+					.rates = SNDRV_PCM_RATE_48000,
+					.rate_min = 48000,
+					.rate_max = 48000,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 48000 },
+					.clock = 0x29
+				}
+			},
+			/* Capture */
+			{
+				.ifnum = 2,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S32_LE,
+					.channels = 2,
+					.fmt_bits = 24,
+					.iface = 2,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x82,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						   USB_ENDPOINT_SYNC_ASYNC |
+						   USB_ENDPOINT_USAGE_IMPLICIT_FB,
+					.rates = SNDRV_PCM_RATE_48000,
+					.rate_min = 48000,
+					.rate_max = 48000,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 48000 },
+					.clock = 0x29
+				}
+			},
+			{
+				.ifnum = -1
+			}
+		}
+	}
+},
+{
+	/*
+	 * Fiero SC-01 (firmware v1.0.0 @ 96 kHz)
+	 */
+	USB_DEVICE(0x2b53, 0x0024),
+	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.vendor_name = "Fiero",
+		.product_name = "SC-01",
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = &(const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_STANDARD_INTERFACE
+			},
+			/* Playback */
+			{
+				.ifnum = 1,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S32_LE,
+					.channels = 2,
+					.fmt_bits = 24,
+					.iface = 1,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x01,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						   USB_ENDPOINT_SYNC_ASYNC,
+					.rates = SNDRV_PCM_RATE_96000,
+					.rate_min = 96000,
+					.rate_max = 96000,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 96000 },
+					.clock = 0x29
+				}
+			},
+			/* Capture */
+			{
+				.ifnum = 2,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S32_LE,
+					.channels = 2,
+					.fmt_bits = 24,
+					.iface = 2,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x82,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						   USB_ENDPOINT_SYNC_ASYNC |
+						   USB_ENDPOINT_USAGE_IMPLICIT_FB,
+					.rates = SNDRV_PCM_RATE_96000,
+					.rate_min = 96000,
+					.rate_max = 96000,
+					.nr_rates = 1,
+					.rate_table = (unsigned int[]) { 96000 },
+					.clock = 0x29
+				}
+			},
+			{
+				.ifnum = -1
+			}
+		}
+	}
+},
+{
+	/*
+	 * Fiero SC-01 (firmware v1.1.0)
+	 */
+	USB_DEVICE(0x2b53, 0x0031),
+	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.vendor_name = "Fiero",
+		.product_name = "SC-01",
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = &(const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 0,
+				.type = QUIRK_AUDIO_STANDARD_INTERFACE
+			},
+			/* Playback */
+			{
+				.ifnum = 1,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S32_LE,
+					.channels = 2,
+					.fmt_bits = 24,
+					.iface = 1,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x01,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						   USB_ENDPOINT_SYNC_ASYNC,
+					.rates = SNDRV_PCM_RATE_48000 |
+						 SNDRV_PCM_RATE_96000,
+					.rate_min = 48000,
+					.rate_max = 96000,
+					.nr_rates = 2,
+					.rate_table = (unsigned int[]) { 48000, 96000 },
+					.clock = 0x29
+				}
+			},
+			/* Capture */
+			{
+				.ifnum = 2,
+				.type = QUIRK_AUDIO_FIXED_ENDPOINT,
+				.data = &(const struct audioformat) {
+					.formats = SNDRV_PCM_FMTBIT_S32_LE,
+					.channels = 2,
+					.fmt_bits = 24,
+					.iface = 2,
+					.altsetting = 1,
+					.altset_idx = 1,
+					.endpoint = 0x82,
+					.ep_attr = USB_ENDPOINT_XFER_ISOC |
+						   USB_ENDPOINT_SYNC_ASYNC |
+						   USB_ENDPOINT_USAGE_IMPLICIT_FB,
+					.rates = SNDRV_PCM_RATE_48000 |
+						 SNDRV_PCM_RATE_96000,
+					.rate_min = 48000,
+					.rate_max = 96000,
+					.nr_rates = 2,
+					.rate_table = (unsigned int[]) { 48000, 96000 },
+					.clock = 0x29
+				}
+			},
+			{
+				.ifnum = -1
+			}
+		}
+	}
+},
+{
+	/* Advanced modes of the Mythware XA001AU.
+	 * For the standard mode, Mythware XA001AU has ID ffad:a001
+	 */
+	USB_DEVICE_VENDOR_SPEC(0xffad, 0xa001),
+	.driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) {
+		.vendor_name = "Mythware",
+		.product_name = "XA001AU",
+		.ifnum = QUIRK_ANY_INTERFACE,
+		.type = QUIRK_COMPOSITE,
+		.data = (const struct snd_usb_audio_quirk[]) {
+			{
+				.ifnum = 0,
+				.type = QUIRK_IGNORE_INTERFACE,
+			},
+			{
+				.ifnum = 1,
+				.type = QUIRK_AUDIO_STANDARD_INTERFACE,
+			},
+			{
+				.ifnum = 2,
+				.type = QUIRK_AUDIO_STANDARD_INTERFACE,
+			},
+			{
+				.ifnum = -1
 			}
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/quirks.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/quirks.c
@@ -591,6 +591,7 @@
 static int snd_usb_extigy_boot_quirk(struct usb_device *dev, struct usb_interface *intf)
 {
 	struct usb_host_config *config = dev->actconfig;
+	struct usb_device_descriptor *new_device_descriptor = NULL;
 	int err;
 
 	if (le16_to_cpu(get_cfg_desc(config)->wTotalLength) == EXTIGY_FIRMWARE_SIZE_OLD ||
@@ -601,11 +602,20 @@
 				      0x10, 0x43, 0x0001, 0x000a, NULL, 0);
 		if (err < 0)
 			dev_dbg(&dev->dev, "error sending boot message: %d\n", err);
+
+		new_device_descriptor = kmalloc(sizeof(*new_device_descriptor), GFP_KERNEL);
+		if (!new_device_descriptor)
+			return -ENOMEM;
 		err = usb_get_descriptor(dev, USB_DT_DEVICE, 0,
-				&dev->descriptor, sizeof(dev->descriptor));
-		config = dev->actconfig;
+				new_device_descriptor, sizeof(*new_device_descriptor));
 		if (err < 0)
 			dev_dbg(&dev->dev, "error usb_get_descriptor: %d\n", err);
+		if (new_device_descriptor->bNumConfigurations > dev->descriptor.bNumConfigurations)
+			dev_dbg(&dev->dev, "error too large bNumConfigurations: %d\n",
+				new_device_descriptor->bNumConfigurations);
+		else
+			memcpy(&dev->descriptor, new_device_descriptor, sizeof(dev->descriptor));
+		kfree(new_device_descriptor);
 		err = usb_reset_configuration(dev);
 		if (err < 0)
 			dev_dbg(&dev->dev, "error usb_reset_configuration: %d\n", err);
@@ -937,6 +947,7 @@
 static int snd_usb_mbox2_boot_quirk(struct usb_device *dev)
 {
 	struct usb_host_config *config = dev->actconfig;
+	struct usb_device_descriptor *new_device_descriptor = NULL;
 	int err;
 	u8 bootresponse[0x12];
 	int fwsize;
@@ -971,11 +982,21 @@
 
 	dev_dbg(&dev->dev, "device initialised!\n");
 
+	new_device_descriptor = kmalloc(sizeof(*new_device_descriptor), GFP_KERNEL);
+	if (!new_device_descriptor)
+		return -ENOMEM;
+
 	err = usb_get_descriptor(dev, USB_DT_DEVICE, 0,
-		&dev->descriptor, sizeof(dev->descriptor));
-	config = dev->actconfig;
+		new_device_descriptor, sizeof(*new_device_descriptor));
 	if (err < 0)
 		dev_dbg(&dev->dev, "error usb_get_descriptor: %d\n", err);
+	if (new_device_descriptor->bNumConfigurations > dev->descriptor.bNumConfigurations)
+		dev_dbg(&dev->dev, "error too large bNumConfigurations: %d\n",
+			new_device_descriptor->bNumConfigurations);
+	else
+		memcpy(&dev->descriptor, new_device_descriptor, sizeof(dev->descriptor));
+
+	kfree(new_device_descriptor);
 
 	err = usb_reset_configuration(dev);
 	if (err < 0)
@@ -1020,7 +1041,6 @@
 	return 0;
 }
 
-
 #define MICROBOOK_BUF_SIZE 128
 
 static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf,
@@ -1125,7 +1145,7 @@
 
 static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev)
 {
-	msleep(2000);
+	msleep(4000);
 
 	return 0;
 }
@@ -1290,7 +1310,7 @@
 	if (chip->usb_id == USB_ID(0x0763, 0x2012))
 		return fasttrackpro_skip_setting_quirk(chip, iface, altno);
 	/* presonus studio 1810c: skip altsets incompatible with device_setup */
-	if (chip->usb_id == USB_ID(0x0194f, 0x010c))
+	if (chip->usb_id == USB_ID(0x194f, 0x010c))
 		return s1810c_skip_setting_quirk(chip, iface, altno);
 
 
@@ -1364,7 +1384,7 @@
 				  unsigned int id)
 {
 	switch (id) {
-	case USB_ID(0x07fd, 0x0008): /* MOTU M Series */
+	case USB_ID(0x07fd, 0x0008): /* MOTU M Series, 1st hardware version */
 		return snd_usb_motu_m_series_boot_quirk(dev);
 	}
 
@@ -1478,9 +1498,11 @@
 	case USB_ID(0x041e, 0x3f19): /* E-Mu 0204 USB */
 		set_format_emu_quirk(subs, fmt);
 		break;
+	case USB_ID(0x534d, 0x0021): /* MacroSilicon MS2100/MS2106 */
 	case USB_ID(0x534d, 0x2109): /* MacroSilicon MS2109 */
 		subs->stream_offset_adj = 2;
 		break;
+	case USB_ID(0x2b73, 0x000a): /* Pioneer DJM-900NXS2 */
 	case USB_ID(0x2b73, 0x0013): /* Pioneer DJM-450 */
 		pioneer_djm_set_format_quirk(subs, 0x0082);
 		break;
@@ -1610,6 +1632,7 @@
 	/* XMOS based USB DACs */
 	switch (chip->usb_id) {
 	case USB_ID(0x1511, 0x0037): /* AURALiC VEGA */
+	case USB_ID(0x21ed, 0xd75a): /* Accuphase DAC-60 option card */
 	case USB_ID(0x2522, 0x0012): /* LH Labs VI DAC Infinity */
 	case USB_ID(0x2772, 0x0230): /* Pro-Ject Pre Box S2 Digital */
 		if (fp->altsetting == 2)
@@ -1723,52 +1746,15 @@
 		/* mic works only when ep packet size is set to wMaxPacketSize */
 		fp->attributes |= UAC_EP_CS_ATTR_FILL_MAX;
 		break;
-
+	case USB_ID(0x3511, 0x2b1e): /* Opencomm2 UC USB Bluetooth dongle */
+		/* mic works only when ep pitch control is not set */
+		if (stream == SNDRV_PCM_STREAM_CAPTURE)
+			fp->attributes &= ~UAC_EP_CS_ATTR_PITCH_CONTROL;
+		break;
 	}
 }
 
 /*
- * registration quirk:
- * the registration is skipped if a device matches with the given ID,
- * unless the interface reaches to the defined one.  This is for delaying
- * the registration until the last known interface, so that the card and
- * devices appear at the same time.
- */
-
-struct registration_quirk {
-	unsigned int usb_id;	/* composed via USB_ID() */
-	unsigned int interface;	/* the interface to trigger register */
-};
-
-#define REG_QUIRK_ENTRY(vendor, product, iface) \
-	{ .usb_id = USB_ID(vendor, product), .interface = (iface) }
-
-static const struct registration_quirk registration_quirks[] = {
-	REG_QUIRK_ENTRY(0x0951, 0x16d8, 2),	/* Kingston HyperX AMP */
-	REG_QUIRK_ENTRY(0x0951, 0x16ed, 2),	/* Kingston HyperX Cloud Alpha S */
-	REG_QUIRK_ENTRY(0x0951, 0x16ea, 2),	/* Kingston HyperX Cloud Flight S */
-	REG_QUIRK_ENTRY(0x0ecb, 0x1f46, 2),	/* JBL Quantum 600 */
-	REG_QUIRK_ENTRY(0x0ecb, 0x1f47, 2),	/* JBL Quantum 800 */
-	REG_QUIRK_ENTRY(0x0ecb, 0x2039, 2),	/* JBL Quantum 400 */
-	REG_QUIRK_ENTRY(0x0ecb, 0x203c, 2),	/* JBL Quantum 600 */
-	REG_QUIRK_ENTRY(0x0ecb, 0x203e, 2),	/* JBL Quantum 800 */
-	{ 0 }					/* terminator */
-};
-
-/* return true if skipping registration */
-bool snd_usb_registration_quirk(struct snd_usb_audio *chip, int iface)
-{
-	const struct registration_quirk *q;
-
-	for (q = registration_quirks; q->usb_id; q++)
-		if (chip->usb_id == q->usb_id)
-			return iface != q->interface;
-
-	/* Register as normal */
-	return false;
-}
-
-/*
  * driver behavior quirk flags
  */
 struct usb_audio_quirk_flags_table {
@@ -1782,6 +1768,8 @@
 
 static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 	/* Device matches */
+	DEVICE_FLG(0x03f0, 0x654a, /* HP 320 FHD Webcam */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	DEVICE_FLG(0x041e, 0x3000, /* Creative SB Extigy */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x041e, 0x4080, /* Creative Live Cam VF0610 */
@@ -1792,10 +1780,18 @@
 		   QUIRK_FLAG_CTL_MSG_DELAY_1M | QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x046d, 0x09a4, /* Logitech QuickCam E 3500 */
 		   QUIRK_FLAG_CTL_MSG_DELAY_1M | QUIRK_FLAG_IGNORE_CTL_ERROR),
+	DEVICE_FLG(0x0499, 0x1506, /* Yamaha THR5 */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x0499, 0x1509, /* Steinberg UR22 */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x0499, 0x3108, /* Yamaha YIT-W12TX */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	DEVICE_FLG(0x04d8, 0xfeea, /* Benchmark DAC1 Pre */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	DEVICE_FLG(0x04e8, 0xa051, /* Samsung USBC Headset (AKG) */
 		   QUIRK_FLAG_SKIP_CLOCK_SELECTOR | QUIRK_FLAG_CTL_MSG_DELAY_5M),
+	DEVICE_FLG(0x0525, 0xa4ad, /* Hamedal C20 usb camero */
+		   QUIRK_FLAG_IFACE_SKIP_CLOSE),
 	DEVICE_FLG(0x054c, 0x0b8c, /* Sony WALKMAN NW-A45 DAC */
 		   QUIRK_FLAG_SET_IFACE_FIRST),
 	DEVICE_FLG(0x0556, 0x0014, /* Phoenix Audio TMX320VC */
@@ -1817,22 +1813,48 @@
 	DEVICE_FLG(0x0644, 0x804a, /* TEAC UD-301 */
 		   QUIRK_FLAG_ITF_USB_DSD_DAC | QUIRK_FLAG_CTL_MSG_DELAY |
 		   QUIRK_FLAG_IFACE_DELAY),
+	DEVICE_FLG(0x0644, 0x805f, /* TEAC Model 12 */
+		   QUIRK_FLAG_FORCE_IFACE_RESET),
 	DEVICE_FLG(0x06f8, 0xb000, /* Hercules DJ Console (Windows Edition) */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x06f8, 0xd002, /* Hercules DJ Console (Macintosh Edition) */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
+	DEVICE_FLG(0x0711, 0x5800, /* MCT Trigger 5 USB-to-HDMI */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	DEVICE_FLG(0x074d, 0x3553, /* Outlaw RR2150 (Micronas UAC3553B) */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x0763, 0x2030, /* M-Audio Fast Track C400 */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x0763, 0x2031, /* M-Audio Fast Track C600 */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x07fd, 0x000b, /* MOTU M Series 2nd hardware revision */
+		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
 	DEVICE_FLG(0x08bb, 0x2702, /* LineX FM Transmitter */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x0951, 0x16ad, /* Kingston HyperX */
 		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
 	DEVICE_FLG(0x0b0e, 0x0349, /* Jabra 550a */
 		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
+	DEVICE_FLG(0x0c45, 0x6340, /* Sonix HD USB Camera */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x0d8c, 0x0014, /* USB Audio Device */
+		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
+	DEVICE_FLG(0x0ecb, 0x205c, /* JBL Quantum610 Wireless */
+		   QUIRK_FLAG_FIXED_RATE),
+	DEVICE_FLG(0x0ecb, 0x2069, /* JBL Quantum810 Wireless */
+		   QUIRK_FLAG_FIXED_RATE),
 	DEVICE_FLG(0x0fd9, 0x0008, /* Hauppauge HVR-950Q */
 		   QUIRK_FLAG_SHARE_MEDIA_DEVICE | QUIRK_FLAG_ALIGN_TRANSFER),
+	DEVICE_FLG(0x1224, 0x2a25, /* Jieli Technology USB PHY 2.0 */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	DEVICE_FLG(0x1395, 0x740a, /* Sennheiser DECT */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x1397, 0x0507, /* Behringer UMC202HD */
+		   QUIRK_FLAG_PLAYBACK_FIRST | QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x1397, 0x0508, /* Behringer UMC204HD */
+		   QUIRK_FLAG_PLAYBACK_FIRST | QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x1397, 0x0509, /* Behringer UMC404HD */
+		   QUIRK_FLAG_PLAYBACK_FIRST | QUIRK_FLAG_GENERIC_IMPLICIT_FB),
 	DEVICE_FLG(0x13e5, 0x0001, /* Serato Phono */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x154e, 0x1002, /* Denon DCD-1500RE */
@@ -1851,10 +1873,18 @@
 		   QUIRK_FLAG_DISABLE_AUTOSUSPEND),
 	DEVICE_FLG(0x17aa, 0x104d, /* Lenovo ThinkStation P620 Internal Speaker + Front Headset */
 		   QUIRK_FLAG_DISABLE_AUTOSUSPEND),
+	DEVICE_FLG(0x1852, 0x5062, /* Luxman D-08u */
+		   QUIRK_FLAG_ITF_USB_DSD_DAC | QUIRK_FLAG_CTL_MSG_DELAY),
 	DEVICE_FLG(0x1852, 0x5065, /* Luxman DA-06 */
 		   QUIRK_FLAG_ITF_USB_DSD_DAC | QUIRK_FLAG_CTL_MSG_DELAY),
 	DEVICE_FLG(0x1901, 0x0191, /* GE B850V3 CP2114 audio interface */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x19f7, 0x0035, /* RODE NT-USB+ */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x1bcf, 0x2281, /* HD Webcam */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x1bcf, 0x2283, /* NexiGo N930AF FHD Webcam */
+		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	DEVICE_FLG(0x2040, 0x7200, /* Hauppauge HVR-950Q */
 		   QUIRK_FLAG_SHARE_MEDIA_DEVICE | QUIRK_FLAG_ALIGN_TRANSFER),
 	DEVICE_FLG(0x2040, 0x7201, /* Hauppauge HVR-950Q-MXL */
@@ -1887,16 +1917,34 @@
 		   QUIRK_FLAG_SHARE_MEDIA_DEVICE | QUIRK_FLAG_ALIGN_TRANSFER),
 	DEVICE_FLG(0x21b4, 0x0081, /* AudioQuest DragonFly */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x2522, 0x0007, /* LH Labs Geek Out HD Audio 1V5 */
+		   QUIRK_FLAG_SET_IFACE_FIRST),
+	DEVICE_FLG(0x262a, 0x9302, /* ddHiFi TC44C */
+		   QUIRK_FLAG_DSD_RAW),
+	DEVICE_FLG(0x2708, 0x0002, /* Audient iD14 */
+		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x2912, 0x30c8, /* Audioengine D1 */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x2b53, 0x0023, /* Fiero SC-01 (firmware v1.0.0 @ 48 kHz) */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x2b53, 0x0024, /* Fiero SC-01 (firmware v1.0.0 @ 96 kHz) */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x2b53, 0x0031, /* Fiero SC-01 (firmware v1.1.0) */
+		   QUIRK_FLAG_GENERIC_IMPLICIT_FB),
+	DEVICE_FLG(0x2d95, 0x8011, /* VIVO USB-C HEADSET */
+		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
+	DEVICE_FLG(0x2d95, 0x8021, /* VIVO USB-C-XE710 HEADSET */
+		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
+	DEVICE_FLG(0x2fc6, 0xf0b7, /* iBasso DC07 Pro */
+		   QUIRK_FLAG_CTL_MSG_DELAY_1M),
 	DEVICE_FLG(0x30be, 0x0101, /* Schiit Hel */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x413c, 0xa506, /* Dell AE515 sound bar */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x534d, 0x0021, /* MacroSilicon MS2100/MS2106 */
+		   QUIRK_FLAG_ALIGN_TRANSFER),
 	DEVICE_FLG(0x534d, 0x2109, /* MacroSilicon MS2109 */
 		   QUIRK_FLAG_ALIGN_TRANSFER),
-	DEVICE_FLG(0x1224, 0x2a25, /* Jieli Technology USB PHY 2.0 */
-		   QUIRK_FLAG_GET_SAMPLE_RATE),
 
 	/* Vendor matches */
 	VENDOR_FLG(0x045e, /* MS Lifecam */
@@ -1932,6 +1980,8 @@
 		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x2ab6, /* T+A devices */
 		   QUIRK_FLAG_DSD_RAW),
+	VENDOR_FLG(0x3336, /* HEM devices */
+		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x3353, /* Khadas devices */
 		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x3842, /* EVGA */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/quirks.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/quirks.h
@@ -48,8 +48,6 @@
 					  struct audioformat *fp,
 					  int stream);
 
-bool snd_usb_registration_quirk(struct snd_usb_audio *chip, int iface);
-
 void snd_usb_init_quirk_flags(struct snd_usb_audio *chip);
 
 #endif /* __USBAUDIO_QUIRKS_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/stream.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/stream.c
@@ -244,8 +244,8 @@
 		SNDRV_CHMAP_FR,		/* right front */
 		SNDRV_CHMAP_FC,		/* center front */
 		SNDRV_CHMAP_LFE,	/* LFE */
-		SNDRV_CHMAP_SL,		/* left surround */
-		SNDRV_CHMAP_SR,		/* right surround */
+		SNDRV_CHMAP_RL,		/* left surround */
+		SNDRV_CHMAP_RR,		/* right surround */
 		SNDRV_CHMAP_FLC,	/* left of center */
 		SNDRV_CHMAP_FRC,	/* right of center */
 		SNDRV_CHMAP_RC,		/* surround */
@@ -300,9 +300,12 @@
 	c = 0;
 
 	if (bits) {
-		for (; bits && *maps; maps++, bits >>= 1)
+		for (; bits && *maps; maps++, bits >>= 1) {
 			if (bits & 1)
 				chmap->map[c++] = *maps;
+			if (c == chmap->channels)
+				break;
+		}
 	} else {
 		/* If we're missing wChannelConfig, then guess something
 		    to make sure the channel map is not skipped entirely */
@@ -495,6 +498,10 @@
 			return 0;
 		}
 	}
+
+	if (chip->card->registered)
+		chip->need_delayed_register = true;
+
 	/* look for an empty stream */
 	list_for_each_entry(as, &chip->pcm_list, list) {
 		if (as->fmt_type != fp->fmt_type)
@@ -502,9 +509,6 @@
 		subs = &as->substream[stream];
 		if (subs->ep_num)
 			continue;
-		if (snd_device_get_state(chip->card, as->pcm) !=
-		    SNDRV_DEV_BUILD)
-			chip->need_delayed_register = true;
 		err = snd_pcm_new_stream(as->pcm, stream, 1);
 		if (err < 0)
 			return err;
@@ -1092,6 +1096,7 @@
 	int i, altno, err, stream;
 	struct audioformat *fp = NULL;
 	struct snd_usb_power_domain *pd = NULL;
+	bool set_iface_first;
 	int num, protocol;
 
 	dev = chip->dev;
@@ -1105,7 +1110,7 @@
 	 * Dallas DS4201 workaround: It presents 5 altsettings, but the last
 	 * one misses syncpipe, and does not produce any sound.
 	 */
-	if (chip->usb_id == USB_ID(0x04fa, 0x4201))
+	if (chip->usb_id == USB_ID(0x04fa, 0x4201) && num >= 4)
 		num = 4;
 
 	for (i = 0; i < num; i++) {
@@ -1222,11 +1227,19 @@
 				return err;
 		}
 
+		set_iface_first = false;
+		if (protocol == UAC_VERSION_1 ||
+		    (chip->quirk_flags & QUIRK_FLAG_SET_IFACE_FIRST))
+			set_iface_first = true;
+
 		/* try to set the interface... */
 		usb_set_interface(chip->dev, iface_no, 0);
+		if (set_iface_first)
+			usb_set_interface(chip->dev, iface_no, altno);
 		snd_usb_init_pitch(chip, fp);
 		snd_usb_init_sample_rate(chip, fp, fp->rate_max);
-		usb_set_interface(chip->dev, iface_no, altno);
+		if (!set_iface_first)
+			usb_set_interface(chip->dev, iface_no, altno);
 	}
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/usbaudio.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/usbaudio.h
@@ -8,7 +8,7 @@
  */
 
 /* handling of USB vendor/product ID pairs as 32-bit numbers */
-#define USB_ID(vendor, product) (((vendor) << 16) | (product))
+#define USB_ID(vendor, product) (((unsigned int)(vendor) << 16) | (product))
 #define USB_ID_VENDOR(id) ((id) >> 16)
 #define USB_ID_PRODUCT(id) ((u16)(id))
 
@@ -37,6 +37,7 @@
 	unsigned int quirk_flags;
 	unsigned int need_delayed_register:1; /* warn for delayed registration */
 	int num_interfaces;
+	int last_iface;
 	int num_suspended_intf;
 	int sample_rate_read_error;
 
@@ -45,6 +46,7 @@
 	struct list_head pcm_list;	/* list of pcm streams */
 	struct list_head ep_list;	/* list of audio-related endpoints */
 	struct list_head iface_ref_list; /* list of interface refcounts */
+	struct list_head clock_ref_list; /* list of clock refcounts */
 	int pcm_devs;
 
 	struct list_head midi_list;	/* list of midi interfaces */
@@ -164,6 +166,18 @@
  *  Support generic DSD raw U32_BE format
  * QUIRK_FLAG_SET_IFACE_FIRST:
  *  Set up the interface at first like UAC1
+ * QUIRK_FLAG_GENERIC_IMPLICIT_FB
+ *  Apply the generic implicit feedback sync mode (same as implicit_fb=1 option)
+ * QUIRK_FLAG_SKIP_IMPLICIT_FB
+ *  Don't apply implicit feedback sync mode
+ * QUIRK_FLAG_IFACE_SKIP_CLOSE
+ *  Don't closed interface during setting sample rate
+ * QUIRK_FLAG_FORCE_IFACE_RESET
+ *  Force an interface reset whenever stopping & restarting a stream
+ *  (e.g. after xrun)
+ * QUIRK_FLAG_FIXED_RATE
+ *  Do not set PCM rate (frequency) when only one rate is available
+ *  for the given endpoint.
  */
 
 #define QUIRK_FLAG_GET_SAMPLE_RATE	(1U << 0)
@@ -183,5 +197,10 @@
 #define QUIRK_FLAG_IGNORE_CTL_ERROR	(1U << 14)
 #define QUIRK_FLAG_DSD_RAW		(1U << 15)
 #define QUIRK_FLAG_SET_IFACE_FIRST	(1U << 16)
+#define QUIRK_FLAG_GENERIC_IMPLICIT_FB	(1U << 17)
+#define QUIRK_FLAG_SKIP_IMPLICIT_FB	(1U << 18)
+#define QUIRK_FLAG_IFACE_SKIP_CLOSE	(1U << 19)
+#define QUIRK_FLAG_FORCE_IFACE_RESET	(1U << 20)
+#define QUIRK_FLAG_FIXED_RATE		(1U << 21)
 
 #endif /* __USBAUDIO_H */
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/usx2y/us122l.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/usx2y/us122l.c
@@ -617,10 +617,7 @@
 	usb_put_intf(usb_ifnum_to_if(us122l->dev, 1));
 	usb_put_dev(us122l->dev);
 
-	while (atomic_read(&us122l->mmap_count))
-		msleep(500);
-
-	snd_card_free(card);
+	snd_card_free_when_closed(card);
 }
 
 static int snd_us122l_suspend(struct usb_interface *intf, pm_message_t message)
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/usx2y/usbusx2y.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/usx2y/usbusx2y.c
@@ -151,6 +151,12 @@
 static void snd_usx2y_card_private_free(struct snd_card *card);
 static void usx2y_unlinkseq(struct snd_usx2y_async_seq *s);
 
+#ifdef USX2Y_NRPACKS_VARIABLE
+int nrpacks = USX2Y_NRPACKS; /* number of packets per urb */
+module_param(nrpacks, int, 0444);
+MODULE_PARM_DESC(nrpacks, "Number of packets per URB.");
+#endif
+
 /*
  * pipe 4 is used for switching the lamps, setting samplerate, volumes ....
  */
@@ -423,7 +429,7 @@
 	}
 	if (usx2y->us428ctls_sharedmem)
 		wake_up(&usx2y->us428ctls_wait_queue_head);
-	snd_card_free(card);
+	snd_card_free_when_closed(card);
 }
 
 static int snd_usx2y_probe(struct usb_interface *intf,
@@ -433,6 +439,11 @@
 	struct snd_card *card;
 	int err;
 
+#ifdef USX2Y_NRPACKS_VARIABLE
+	if (nrpacks < 0 || nrpacks > USX2Y_NRPACKS_MAX)
+		return -EINVAL;
+#endif
+
 	if (le16_to_cpu(device->descriptor.idVendor) != 0x1604 ||
 	    (le16_to_cpu(device->descriptor.idProduct) != USB_ID_US122 &&
 	     le16_to_cpu(device->descriptor.idProduct) != USB_ID_US224 &&
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/usx2y/usbusx2y.h
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/usx2y/usbusx2y.h
@@ -7,6 +7,32 @@
 
 #define NRURBS	        2
 
+/* Default value used for nr of packs per urb.
+ * 1 to 4 have been tested ok on uhci.
+ * To use 3 on ohci, you'd need a patch:
+ * look for "0000425-linux-2.6.9-rc4-mm1_ohci-hcd.patch.gz" on
+ * "https://bugtrack.alsa-project.org/alsa-bug/bug_view_page.php?bug_id=0000425"
+ *
+ * 1, 2 and 4 work out of the box on ohci, if I recall correctly.
+ * Bigger is safer operation, smaller gives lower latencies.
+ */
+#define USX2Y_NRPACKS 4
+
+#define USX2Y_NRPACKS_MAX 1024
+
+/* If your system works ok with this module's parameter
+ * nrpacks set to 1, you might as well comment
+ * this define out, and thereby produce smaller, faster code.
+ * You'd also set USX2Y_NRPACKS to 1 then.
+ */
+#define USX2Y_NRPACKS_VARIABLE 1
+
+#ifdef USX2Y_NRPACKS_VARIABLE
+extern int nrpacks;
+#define nr_of_packs() nrpacks
+#else
+#define nr_of_packs() USX2Y_NRPACKS
+#endif
 
 #define URBS_ASYNC_SEQ 10
 #define URB_DATA_LEN_ASYNC_SEQ 32
--- linux-xilinx-zynqmp-5.15.0.orig/sound/usb/usx2y/usbusx2yaudio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/usb/usx2y/usbusx2yaudio.c
@@ -28,33 +28,6 @@
 #include "usx2y.h"
 #include "usbusx2y.h"
 
-/* Default value used for nr of packs per urb.
- * 1 to 4 have been tested ok on uhci.
- * To use 3 on ohci, you'd need a patch:
- * look for "0000425-linux-2.6.9-rc4-mm1_ohci-hcd.patch.gz" on
- * "https://bugtrack.alsa-project.org/alsa-bug/bug_view_page.php?bug_id=0000425"
- *
- * 1, 2 and 4 work out of the box on ohci, if I recall correctly.
- * Bigger is safer operation, smaller gives lower latencies.
- */
-#define USX2Y_NRPACKS 4
-
-/* If your system works ok with this module's parameter
- * nrpacks set to 1, you might as well comment
- * this define out, and thereby produce smaller, faster code.
- * You'd also set USX2Y_NRPACKS to 1 then.
- */
-#define USX2Y_NRPACKS_VARIABLE 1
-
-#ifdef USX2Y_NRPACKS_VARIABLE
-static int nrpacks = USX2Y_NRPACKS; /* number of packets per urb */
-#define  nr_of_packs() nrpacks
-module_param(nrpacks, int, 0444);
-MODULE_PARM_DESC(nrpacks, "Number of packets per URB.");
-#else
-#define nr_of_packs() USX2Y_NRPACKS
-#endif
-
 static int usx2y_urb_capt_retire(struct snd_usx2y_substream *subs)
 {
 	struct urb	*urb = subs->completed_urb;
--- linux-xilinx-zynqmp-5.15.0.orig/sound/x86/intel_hdmi_audio.c
+++ linux-xilinx-zynqmp-5.15.0/sound/x86/intel_hdmi_audio.c
@@ -1261,7 +1261,7 @@
 {
 	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
 	return remap_pfn_range(vma, vma->vm_start,
-			substream->dma_buffer.addr >> PAGE_SHIFT,
+			substream->runtime->dma_addr >> PAGE_SHIFT,
 			vma->vm_end - vma->vm_start, vma->vm_page_prot);
 }
 
@@ -1665,7 +1665,7 @@
  * This function is called when the i915 driver creates the
  * hdmi-lpe-audio platform device.
  */
-static int hdmi_lpe_audio_probe(struct platform_device *pdev)
+static int __hdmi_lpe_audio_probe(struct platform_device *pdev)
 {
 	struct snd_card *card;
 	struct snd_intelhad_card *card_ctx;
@@ -1826,6 +1826,11 @@
 	return 0;
 }
 
+static int hdmi_lpe_audio_probe(struct platform_device *pdev)
+{
+	return snd_card_free_on_error(&pdev->dev, __hdmi_lpe_audio_probe(pdev));
+}
+
 static const struct dev_pm_ops hdmi_lpe_audio_pm = {
 	SET_SYSTEM_SLEEP_PM_OPS(hdmi_lpe_audio_suspend, hdmi_lpe_audio_resume)
 };
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/parisc/include/uapi/asm/errno.h
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/parisc/include/uapi/asm/errno.h
@@ -75,7 +75,6 @@
 
 /* We now return you to your regularly scheduled HPUX. */
 
-#define ENOSYM		215	/* symbol does not exist in executable */
 #define	ENOTSOCK	216	/* Socket operation on non-socket */
 #define	EDESTADDRREQ	217	/* Destination address required */
 #define	EMSGSIZE	218	/* Message too long */
@@ -101,7 +100,6 @@
 #define	ETIMEDOUT	238	/* Connection timed out */
 #define	ECONNREFUSED	239	/* Connection refused */
 #define	EREFUSED	ECONNREFUSED	/* for HP's NFS apparently */
-#define	EREMOTERELEASE	240	/* Remote peer released connection */
 #define	EHOSTDOWN	241	/* Host is down */
 #define	EHOSTUNREACH	242	/* No route to host */
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/parisc/include/uapi/asm/mman.h
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/parisc/include/uapi/asm/mman.h
@@ -1,20 +1,20 @@
 /* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
 #ifndef TOOLS_ARCH_PARISC_UAPI_ASM_MMAN_FIX_H
 #define TOOLS_ARCH_PARISC_UAPI_ASM_MMAN_FIX_H
-#define MADV_DODUMP	70
+#define MADV_DODUMP	17
 #define MADV_DOFORK	11
-#define MADV_DONTDUMP   69
+#define MADV_DONTDUMP   16
 #define MADV_DONTFORK	10
 #define MADV_DONTNEED   4
 #define MADV_FREE	8
-#define MADV_HUGEPAGE	67
-#define MADV_MERGEABLE   65
-#define MADV_NOHUGEPAGE	68
+#define MADV_HUGEPAGE	14
+#define MADV_MERGEABLE  12
+#define MADV_NOHUGEPAGE 15
 #define MADV_NORMAL     0
 #define MADV_RANDOM     1
 #define MADV_REMOVE	9
 #define MADV_SEQUENTIAL 2
-#define MADV_UNMERGEABLE 66
+#define MADV_UNMERGEABLE 13
 #define MADV_WILLNEED   3
 #define MAP_ANONYMOUS	0x10
 #define MAP_DENYWRITE	0x0800
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/include/asm/cpufeatures.h
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/include/asm/cpufeatures.h
@@ -14,7 +14,7 @@
  * Defines x86 CPU feature bits
  */
 #define NCAPINTS			20	   /* N 32-bit words worth of info */
-#define NBUGINTS			1	   /* N 32-bit bug flags */
+#define NBUGINTS			2	   /* N 32-bit bug flags */
 
 /*
  * Note: If the comment begins with a quoted string, that string is used
@@ -203,8 +203,8 @@
 #define X86_FEATURE_PROC_FEEDBACK	( 7*32+ 9) /* AMD ProcFeedbackInterface */
 /* FREE!                                ( 7*32+10) */
 #define X86_FEATURE_PTI			( 7*32+11) /* Kernel Page Table Isolation enabled */
-#define X86_FEATURE_RETPOLINE		( 7*32+12) /* "" Generic Retpoline mitigation for Spectre variant 2 */
-#define X86_FEATURE_RETPOLINE_AMD	( 7*32+13) /* "" AMD Retpoline mitigation for Spectre variant 2 */
+#define X86_FEATURE_KERNEL_IBRS		( 7*32+12) /* "" Set/clear IBRS on kernel entry/exit */
+#define X86_FEATURE_RSB_VMEXIT		( 7*32+13) /* "" Fill RSB on VM-Exit */
 #define X86_FEATURE_INTEL_PPIN		( 7*32+14) /* Intel Processor Inventory Number */
 #define X86_FEATURE_CDP_L2		( 7*32+15) /* Code and Data Prioritization L2 */
 #define X86_FEATURE_MSR_SPEC_CTRL	( 7*32+16) /* "" MSR SPEC_CTRL is implemented */
@@ -294,6 +294,13 @@
 #define X86_FEATURE_PER_THREAD_MBA	(11*32+ 7) /* "" Per-thread Memory Bandwidth Allocation */
 #define X86_FEATURE_SGX1		(11*32+ 8) /* "" Basic SGX */
 #define X86_FEATURE_SGX2		(11*32+ 9) /* "" SGX Enclave Dynamic Memory Management (EDMM) */
+#define X86_FEATURE_ENTRY_IBPB		(11*32+10) /* "" Issue an IBPB on kernel entry */
+#define X86_FEATURE_RRSBA_CTRL		(11*32+11) /* "" RET prediction control */
+#define X86_FEATURE_RETPOLINE		(11*32+12) /* "" Generic Retpoline mitigation for Spectre variant 2 */
+#define X86_FEATURE_RETPOLINE_LFENCE	(11*32+13) /* "" Use LFENCE for Spectre variant 2 */
+#define X86_FEATURE_RETHUNK		(11*32+14) /* "" Use REturn THUNK */
+#define X86_FEATURE_UNRET		(11*32+15) /* "" AMD BTB untrain return */
+#define X86_FEATURE_RSB_VMEXIT_LITE	(11*32+17) /* "" Fill RSB on VM-Exit when EIBRS is enabled */
 
 /* Intel-defined CPU features, CPUID level 0x00000007:1 (EAX), word 12 */
 #define X86_FEATURE_AVX_VNNI		(12*32+ 4) /* AVX VNNI instructions */
@@ -313,6 +320,7 @@
 #define X86_FEATURE_AMD_SSBD		(13*32+24) /* "" Speculative Store Bypass Disable */
 #define X86_FEATURE_VIRT_SSBD		(13*32+25) /* Virtualized Speculative Store Bypass Disable */
 #define X86_FEATURE_AMD_SSB_NO		(13*32+26) /* "" Speculative Store Bypass is fixed in hardware. */
+#define X86_FEATURE_BTC_NO		(13*32+29) /* "" Not vulnerable to Branch Type Confusion */
 
 /* Thermal and Power Management Leaf, CPUID level 0x00000006 (EAX), word 14 */
 #define X86_FEATURE_DTHERM		(14*32+ 0) /* Digital Thermal Sensor */
@@ -436,5 +444,7 @@
 #define X86_BUG_TAA			X86_BUG(22) /* CPU is affected by TSX Async Abort(TAA) */
 #define X86_BUG_ITLB_MULTIHIT		X86_BUG(23) /* CPU may incur MCE during certain page attribute changes */
 #define X86_BUG_SRBDS			X86_BUG(24) /* CPU may leak RNG bits if not mitigated */
+#define X86_BUG_MMIO_STALE_DATA		X86_BUG(25) /* CPU is affected by Processor MMIO Stale Data vulnerabilities */
+#define X86_BUG_RETBLEED		X86_BUG(26) /* CPU is affected by RETBleed */
 
 #endif /* _ASM_X86_CPUFEATURES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/include/asm/disabled-features.h
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/include/asm/disabled-features.h
@@ -56,6 +56,25 @@
 # define DISABLE_PTI		(1 << (X86_FEATURE_PTI & 31))
 #endif
 
+#ifdef CONFIG_RETPOLINE
+# define DISABLE_RETPOLINE	0
+#else
+# define DISABLE_RETPOLINE	((1 << (X86_FEATURE_RETPOLINE & 31)) | \
+				 (1 << (X86_FEATURE_RETPOLINE_LFENCE & 31)))
+#endif
+
+#ifdef CONFIG_RETHUNK
+# define DISABLE_RETHUNK	0
+#else
+# define DISABLE_RETHUNK	(1 << (X86_FEATURE_RETHUNK & 31))
+#endif
+
+#ifdef CONFIG_CPU_UNRET_ENTRY
+# define DISABLE_UNRET		0
+#else
+# define DISABLE_UNRET		(1 << (X86_FEATURE_UNRET & 31))
+#endif
+
 /* Force disable because it's broken beyond repair */
 #define DISABLE_ENQCMD		(1 << (X86_FEATURE_ENQCMD & 31))
 
@@ -79,7 +98,7 @@
 #define DISABLED_MASK8	0
 #define DISABLED_MASK9	(DISABLE_SMAP|DISABLE_SGX)
 #define DISABLED_MASK10	0
-#define DISABLED_MASK11	0
+#define DISABLED_MASK11	(DISABLE_RETPOLINE|DISABLE_RETHUNK|DISABLE_UNRET)
 #define DISABLED_MASK12	0
 #define DISABLED_MASK13	0
 #define DISABLED_MASK14	0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/include/asm/msr-index.h
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/include/asm/msr-index.h
@@ -51,6 +51,8 @@
 #define SPEC_CTRL_STIBP			BIT(SPEC_CTRL_STIBP_SHIFT)	/* STIBP mask */
 #define SPEC_CTRL_SSBD_SHIFT		2	   /* Speculative Store Bypass Disable bit */
 #define SPEC_CTRL_SSBD			BIT(SPEC_CTRL_SSBD_SHIFT)	/* Speculative Store Bypass Disable */
+#define SPEC_CTRL_RRSBA_DIS_S_SHIFT	6	   /* Disable RRSBA behavior */
+#define SPEC_CTRL_RRSBA_DIS_S		BIT(SPEC_CTRL_RRSBA_DIS_S_SHIFT)
 
 #define MSR_IA32_PRED_CMD		0x00000049 /* Prediction Command */
 #define PRED_CMD_IBPB			BIT(0)	   /* Indirect Branch Prediction Barrier */
@@ -91,6 +93,7 @@
 #define MSR_IA32_ARCH_CAPABILITIES	0x0000010a
 #define ARCH_CAP_RDCL_NO		BIT(0)	/* Not susceptible to Meltdown */
 #define ARCH_CAP_IBRS_ALL		BIT(1)	/* Enhanced IBRS support */
+#define ARCH_CAP_RSBA			BIT(2)	/* RET may use alternative branch predictors */
 #define ARCH_CAP_SKIP_VMENTRY_L1DFLUSH	BIT(3)	/* Skip L1D flush on vmentry */
 #define ARCH_CAP_SSB_NO			BIT(4)	/*
 						 * Not susceptible to Speculative Store Bypass
@@ -114,6 +117,41 @@
 						 * Not susceptible to
 						 * TSX Async Abort (TAA) vulnerabilities.
 						 */
+#define ARCH_CAP_SBDR_SSDP_NO		BIT(13)	/*
+						 * Not susceptible to SBDR and SSDP
+						 * variants of Processor MMIO stale data
+						 * vulnerabilities.
+						 */
+#define ARCH_CAP_FBSDP_NO		BIT(14)	/*
+						 * Not susceptible to FBSDP variant of
+						 * Processor MMIO stale data
+						 * vulnerabilities.
+						 */
+#define ARCH_CAP_PSDP_NO		BIT(15)	/*
+						 * Not susceptible to PSDP variant of
+						 * Processor MMIO stale data
+						 * vulnerabilities.
+						 */
+#define ARCH_CAP_FB_CLEAR		BIT(17)	/*
+						 * VERW clears CPU fill buffer
+						 * even on MDS_NO CPUs.
+						 */
+#define ARCH_CAP_FB_CLEAR_CTRL		BIT(18)	/*
+						 * MSR_IA32_MCU_OPT_CTRL[FB_CLEAR_DIS]
+						 * bit available to control VERW
+						 * behavior.
+						 */
+#define ARCH_CAP_RRSBA			BIT(19)	/*
+						 * Indicates RET may use predictors
+						 * other than the RSB. With eIBRS
+						 * enabled predictions in kernel mode
+						 * are restricted to targets in
+						 * kernel.
+						 */
+#define ARCH_CAP_PBRSB_NO		BIT(24)	/*
+						 * Not susceptible to Post-Barrier
+						 * Return Stack Buffer Predictions.
+						 */
 
 #define MSR_IA32_FLUSH_CMD		0x0000010b
 #define L1D_FLUSH			BIT(0)	/*
@@ -128,9 +166,10 @@
 #define TSX_CTRL_RTM_DISABLE		BIT(0)	/* Disable RTM feature */
 #define TSX_CTRL_CPUID_CLEAR		BIT(1)	/* Disable TSX enumeration */
 
-/* SRBDS support */
 #define MSR_IA32_MCU_OPT_CTRL		0x00000123
-#define RNGDS_MITG_DIS			BIT(0)
+#define RNGDS_MITG_DIS			BIT(0)	/* SRBDS support */
+#define RTM_ALLOW			BIT(1)	/* TSX development mode */
+#define FB_CLEAR_DIS			BIT(3)	/* CPU Fill buffer clear disable */
 
 #define MSR_IA32_SYSENTER_CS		0x00000174
 #define MSR_IA32_SYSENTER_ESP		0x00000175
@@ -456,6 +495,11 @@
 #define MSR_AMD64_CPUID_FN_1		0xc0011004
 #define MSR_AMD64_LS_CFG		0xc0011020
 #define MSR_AMD64_DC_CFG		0xc0011022
+
+#define MSR_AMD64_DE_CFG		0xc0011029
+#define MSR_AMD64_DE_CFG_LFENCE_SERIALIZE_BIT	1
+#define MSR_AMD64_DE_CFG_LFENCE_SERIALIZE	BIT_ULL(MSR_AMD64_DE_CFG_LFENCE_SERIALIZE_BIT)
+
 #define MSR_AMD64_BU_CFG2		0xc001102a
 #define MSR_AMD64_IBSFETCHCTL		0xc0011030
 #define MSR_AMD64_IBSFETCHLINAD		0xc0011031
@@ -489,6 +533,9 @@
 /* Fam 17h MSRs */
 #define MSR_F17H_IRPERF			0xc00000e9
 
+#define MSR_ZEN2_SPECTRAL_CHICKEN	0xc00110e3
+#define MSR_ZEN2_SPECTRAL_CHICKEN_BIT	BIT_ULL(1)
+
 /* Fam 16h MSRs */
 #define MSR_F16H_L2I_PERF_CTL		0xc0010230
 #define MSR_F16H_L2I_PERF_CTR		0xc0010231
@@ -530,9 +577,6 @@
 #define FAM10H_MMIO_CONF_BASE_MASK	0xfffffffULL
 #define FAM10H_MMIO_CONF_BASE_SHIFT	20
 #define MSR_FAM10H_NODE_ID		0xc001100c
-#define MSR_F10H_DECFG			0xc0011029
-#define MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT	1
-#define MSR_F10H_DECFG_LFENCE_SERIALIZE		BIT_ULL(MSR_F10H_DECFG_LFENCE_SERIALIZE_BIT)
 
 /* K8 MSRs */
 #define MSR_K8_TOP_MEM1			0xc001001a
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/kcpuid/cpuid.csv
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/kcpuid/cpuid.csv
@@ -184,8 +184,8 @@
 	 7,    0,  EBX,     27, avx512er, AVX512 Exponent Reciproca instr
 	 7,    0,  EBX,     28, avx512cd, AVX512 Conflict Detection instr
 	 7,    0,  EBX,     29, sha, Intel Secure Hash Algorithm Extensions instr
-	 7,    0,  EBX,     26, avx512bw, AVX512 Byte & Word instr
-	 7,    0,  EBX,     28, avx512vl, AVX512 Vector Length Extentions (VL)
+	 7,    0,  EBX,     30, avx512bw, AVX512 Byte & Word instr
+	 7,    0,  EBX,     31, avx512vl, AVX512 Vector Length Extentions (VL)
 	 7,    0,  ECX,      0, prefetchwt1, X
 	 7,    0,  ECX,      1, avx512vbmi, AVX512 Vector Byte Manipulation Instructions
 	 7,    0,  ECX,      2, umip, User-mode Instruction Prevention
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/kcpuid/kcpuid.c
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/kcpuid/kcpuid.c
@@ -7,7 +7,8 @@
 #include <string.h>
 #include <getopt.h>
 
-#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
+#define ARRAY_SIZE(x)	(sizeof(x) / sizeof((x)[0]))
+#define min(a, b)	(((a) < (b)) ? (a) : (b))
 
 typedef unsigned int u32;
 typedef unsigned long long u64;
@@ -203,12 +204,9 @@
 #define MAX_SUBLEAF_NUM		32
 struct cpuid_range *setup_cpuid_range(u32 input_eax)
 {
-	u32 max_func, idx_func;
-	int subleaf;
+	u32 max_func, idx_func, subleaf, max_subleaf;
+	u32 eax, ebx, ecx, edx, f = input_eax;
 	struct cpuid_range *range;
-	u32 eax, ebx, ecx, edx;
-	u32 f = input_eax;
-	int max_subleaf;
 	bool allzero;
 
 	eax = input_eax;
@@ -254,7 +252,7 @@
 		 * others have to be tried (0xf)
 		 */
 		if (f == 0x7 || f == 0x14 || f == 0x17 || f == 0x18)
-			max_subleaf = (eax & 0xff) + 1;
+			max_subleaf = min((eax & 0xff) + 1, max_subleaf);
 
 		if (f == 0xb)
 			max_subleaf = 2;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/lib/insn.c
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/lib/insn.c
@@ -13,6 +13,7 @@
 #endif
 #include "../include/asm/inat.h" /* __ignore_sync_check__ */
 #include "../include/asm/insn.h" /* __ignore_sync_check__ */
+#include "../include/asm-generic/unaligned.h" /* __ignore_sync_check__ */
 
 #include <linux/errno.h>
 #include <linux/kconfig.h>
@@ -37,10 +38,10 @@
 	((insn)->next_byte + sizeof(t) + n <= (insn)->end_kaddr)
 
 #define __get_next(t, insn)	\
-	({ t r; memcpy(&r, insn->next_byte, sizeof(t)); insn->next_byte += sizeof(t); leXX_to_cpu(t, r); })
+	({ t r = get_unaligned((t *)(insn)->next_byte); (insn)->next_byte += sizeof(t); leXX_to_cpu(t, r); })
 
 #define __peek_nbyte_next(t, insn, n)	\
-	({ t r; memcpy(&r, (insn)->next_byte + n, sizeof(t)); leXX_to_cpu(t, r); })
+	({ t r = get_unaligned((t *)(insn)->next_byte + n); leXX_to_cpu(t, r); })
 
 #define get_next(t, insn)	\
 	({ if (unlikely(!validate_next(t, insn, 0))) goto err_out; __get_next(t, insn); })
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/lib/memcpy_64.S
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/lib/memcpy_64.S
@@ -39,7 +39,7 @@
 	rep movsq
 	movl %edx, %ecx
 	rep movsb
-	ret
+	RET
 SYM_FUNC_END(memcpy)
 SYM_FUNC_END_ALIAS(__memcpy)
 EXPORT_SYMBOL(memcpy)
@@ -53,7 +53,7 @@
 	movq %rdi, %rax
 	movq %rdx, %rcx
 	rep movsb
-	ret
+	RET
 SYM_FUNC_END(memcpy_erms)
 
 SYM_FUNC_START_LOCAL(memcpy_orig)
@@ -137,7 +137,7 @@
 	movq %r9,	1*8(%rdi)
 	movq %r10,	-2*8(%rdi, %rdx)
 	movq %r11,	-1*8(%rdi, %rdx)
-	retq
+	RET
 	.p2align 4
 .Lless_16bytes:
 	cmpl $8,	%edx
@@ -149,7 +149,7 @@
 	movq -1*8(%rsi, %rdx),	%r9
 	movq %r8,	0*8(%rdi)
 	movq %r9,	-1*8(%rdi, %rdx)
-	retq
+	RET
 	.p2align 4
 .Lless_8bytes:
 	cmpl $4,	%edx
@@ -162,7 +162,7 @@
 	movl -4(%rsi, %rdx), %r8d
 	movl %ecx, (%rdi)
 	movl %r8d, -4(%rdi, %rdx)
-	retq
+	RET
 	.p2align 4
 .Lless_3bytes:
 	subl $1, %edx
@@ -180,7 +180,7 @@
 	movb %cl, (%rdi)
 
 .Lend:
-	retq
+	RET
 SYM_FUNC_END(memcpy_orig)
 
 .popsection
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/lib/memset_64.S
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/lib/memset_64.S
@@ -40,7 +40,7 @@
 	movl %edx,%ecx
 	rep stosb
 	movq %r9,%rax
-	ret
+	RET
 SYM_FUNC_END(__memset)
 SYM_FUNC_END_ALIAS(memset)
 EXPORT_SYMBOL(memset)
@@ -63,7 +63,7 @@
 	movq %rdx,%rcx
 	rep stosb
 	movq %r9,%rax
-	ret
+	RET
 SYM_FUNC_END(memset_erms)
 
 SYM_FUNC_START_LOCAL(memset_orig)
@@ -125,7 +125,7 @@
 
 .Lende:
 	movq	%r10,%rax
-	ret
+	RET
 
 .Lbad_alignment:
 	cmpq $7,%rdx
--- linux-xilinx-zynqmp-5.15.0.orig/tools/arch/x86/lib/x86-opcode-map.txt
+++ linux-xilinx-zynqmp-5.15.0/tools/arch/x86/lib/x86-opcode-map.txt
@@ -148,7 +148,7 @@
 65: SEG=GS (Prefix)
 66: Operand-Size (Prefix)
 67: Address-Size (Prefix)
-68: PUSH Iz (d64)
+68: PUSH Iz
 69: IMUL Gv,Ev,Iz
 6a: PUSH Ib (d64)
 6b: IMUL Gv,Ev,Ib
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bootconfig/main.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bootconfig/main.c
@@ -225,7 +225,7 @@
 	/* Wrong Checksum */
 	rcsum = xbc_calc_checksum(*buf, size);
 	if (csum != rcsum) {
-		pr_err("checksum error: %d != %d\n", csum, rcsum);
+		pr_err("checksum error: %u != %u\n", csum, rcsum);
 		return -EINVAL;
 	}
 
@@ -393,7 +393,7 @@
 	printf("Apply %s to %s\n", xbc_path, path);
 	printf("\tNumber of nodes: %d\n", ret);
 	printf("\tSize: %u bytes\n", (unsigned int)size);
-	printf("\tChecksum: %d\n", (unsigned int)csum);
+	printf("\tChecksum: %u\n", (unsigned int)csum);
 
 	/* TODO: Check the options by schema */
 	xbc_destroy_all();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bootconfig/scripts/ftrace2bconf.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/bootconfig/scripts/ftrace2bconf.sh
@@ -93,7 +93,7 @@
 }
 
 event_is_enabled() { # enable-file
-	test -f $1 & grep -q "1" $1
+	test -f $1 && grep -q "1" $1
 }
 
 per_event_options() { # event-dir
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bootconfig/test-bootconfig.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/bootconfig/test-bootconfig.sh
@@ -87,10 +87,14 @@
 
 echo "Max node number check"
 
-echo -n > $TEMPCONF
-for i in `seq 1 1024` ; do
-   echo "node$i" >> $TEMPCONF
-done
+awk '
+BEGIN {
+  for (i = 0; i < 26; i += 1)
+      printf("%c\n", 65 + i % 26)
+  for (i = 26; i < 8192; i += 1)
+      printf("%c%c%c\n", 65 + i % 26, 65 + (i / 26) % 26, 65 + (i / 26 / 26))
+}
+' > $TEMPCONF
 xpass $BOOTCONF -a $TEMPCONF $INITRD
 
 echo "badnode" >> $TEMPCONF
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/Makefile
@@ -34,7 +34,7 @@
 endif
 
 FEATURE_USER = .bpf
-FEATURE_TESTS = libbfd disassembler-four-args
+FEATURE_TESTS = libbfd disassembler-four-args disassembler-init-styled
 FEATURE_DISPLAY = libbfd disassembler-four-args
 
 check_feat := 1
@@ -56,6 +56,9 @@
 ifeq ($(feature-disassembler-four-args), 1)
 CFLAGS += -DDISASM_FOUR_ARGS_SIGNATURE
 endif
+ifeq ($(feature-disassembler-init-styled), 1)
+CFLAGS += -DDISASM_INIT_STYLED
+endif
 
 $(OUTPUT)%.yacc.c: $(srctree)/tools/bpf/%.y
 	$(QUIET_BISON)$(YACC) -o $@ -d $<
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpf_jit_disasm.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpf_jit_disasm.c
@@ -28,6 +28,7 @@
 #include <sys/types.h>
 #include <sys/stat.h>
 #include <limits.h>
+#include <tools/dis-asm-compat.h>
 
 #define CMD_ACTION_SIZE_BUFFER		10
 #define CMD_ACTION_READ_ALL		3
@@ -64,7 +65,9 @@
 	assert(bfdf);
 	assert(bfd_check_format(bfdf, bfd_object));
 
-	init_disassemble_info(&info, stdout, (fprintf_ftype) fprintf);
+	init_disassemble_info_compat(&info, stdout,
+				     (fprintf_ftype) fprintf,
+				     fprintf_styled);
 	info.arch = bfd_get_arch(bfdf);
 	info.mach = bfd_get_mach(bfdf);
 	info.buffer = image;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/Makefile
@@ -1,6 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
 include ../../../scripts/Makefile.include
-include ../../../scripts/utilities.mak
 
 INSTALL ?= install
 RM ?= rm -f
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool-btf.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool-btf.rst
@@ -13,7 +13,7 @@
 	**bpftool** [*OPTIONS*] **btf** *COMMAND*
 
 	*OPTIONS* := { { **-j** | **--json** } [{ **-p** | **--pretty** }] | {**-d** | **--debug** } |
-		{ **-B** | **--base-btf** } }
+	{ **-B** | **--base-btf** } }
 
 	*COMMANDS* := { **dump** | **help** }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool-cgroup.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool-cgroup.rst
@@ -13,7 +13,7 @@
 	**bpftool** [*OPTIONS*] **cgroup** *COMMAND*
 
 	*OPTIONS* := { { **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } |
-		{ **-f** | **--bpffs** } }
+	{ **-f** | **--bpffs** } }
 
 	*COMMANDS* :=
 	{ **show** | **list** | **tree** | **attach** | **detach** | **help** }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool-gen.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool-gen.rst
@@ -13,7 +13,7 @@
 	**bpftool** [*OPTIONS*] **gen** *COMMAND*
 
 	*OPTIONS* := { { **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } |
-		{ **-L** | **--use-loader** } }
+	{ **-L** | **--use-loader** } }
 
 	*COMMAND* := { **object** | **skeleton** | **help** }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool-link.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool-link.rst
@@ -13,7 +13,7 @@
 	**bpftool** [*OPTIONS*] **link** *COMMAND*
 
 	*OPTIONS* := { { **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } |
-		{ **-f** | **--bpffs** } | { **-n** | **--nomount** } }
+	{ **-f** | **--bpffs** } | { **-n** | **--nomount** } }
 
 	*COMMANDS* := { **show** | **list** | **pin** | **help** }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool-map.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool-map.rst
@@ -13,11 +13,11 @@
 	**bpftool** [*OPTIONS*] **map** *COMMAND*
 
 	*OPTIONS* := { { **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } |
-		{ **-f** | **--bpffs** } | { **-n** | **--nomount** } }
+	{ **-f** | **--bpffs** } | { **-n** | **--nomount** } }
 
 	*COMMANDS* :=
-	{ **show** | **list** | **create** | **dump** | **update** | **lookup** | **getnext**
-	| **delete** | **pin** | **help** }
+	{ **show** | **list** | **create** | **dump** | **update** | **lookup** | **getnext** |
+	**delete** | **pin** | **help** }
 
 MAP COMMANDS
 =============
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool-prog.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool-prog.rst
@@ -13,12 +13,12 @@
 	**bpftool** [*OPTIONS*] **prog** *COMMAND*
 
 	*OPTIONS* := { { **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } |
-		{ **-f** | **--bpffs** } | { **-m** | **--mapcompat** } | { **-n** | **--nomount** } |
-		{ **-L** | **--use-loader** } }
+	{ **-f** | **--bpffs** } | { **-m** | **--mapcompat** } | { **-n** | **--nomount** } |
+	{ **-L** | **--use-loader** } }
 
 	*COMMANDS* :=
-	{ **show** | **list** | **dump xlated** | **dump jited** | **pin** | **load**
-	| **loadall** | **help** }
+	{ **show** | **list** | **dump xlated** | **dump jited** | **pin** | **load** |
+	**loadall** | **help** }
 
 PROG COMMANDS
 =============
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Documentation/bpftool.rst
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Documentation/bpftool.rst
@@ -19,14 +19,14 @@
 	*OBJECT* := { **map** | **program** | **cgroup** | **perf** | **net** | **feature** }
 
 	*OPTIONS* := { { **-V** | **--version** } |
-		{ **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } }
+	{ **-j** | **--json** } [{ **-p** | **--pretty** }] | { **-d** | **--debug** } }
 
 	*MAP-COMMANDS* :=
 	{ **show** | **list** | **create** | **dump** | **update** | **lookup** | **getnext** |
-		**delete** | **pin** | **event_pipe** | **help** }
+	**delete** | **pin** | **event_pipe** | **help** }
 
 	*PROG-COMMANDS* := { **show** | **list** | **dump jited** | **dump xlated** | **pin** |
-		**load** | **attach** | **detach** | **help** }
+	**load** | **attach** | **detach** | **help** }
 
 	*CGROUP-COMMANDS* := { **show** | **list** | **attach** | **detach** | **help** }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/Makefile
@@ -1,6 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
 include ../../scripts/Makefile.include
-include ../../scripts/utilities.mak
 
 ifeq ($(srctree),)
 srctree := $(patsubst %/,%,$(dir $(CURDIR)))
@@ -77,7 +76,7 @@
 RM ?= rm -f
 
 FEATURE_USER = .bpftool
-FEATURE_TESTS = libbfd disassembler-four-args reallocarray zlib libcap \
+FEATURE_TESTS = libbfd disassembler-four-args disassembler-init-styled reallocarray zlib libcap \
 	clang-bpf-co-re
 FEATURE_DISPLAY = libbfd disassembler-four-args zlib libcap \
 	clang-bpf-co-re
@@ -112,6 +111,9 @@
 CFLAGS += -DUSE_LIBCAP
 LIBS += -lcap
 endif
+ifeq ($(feature-disassembler-init-styled), 1)
+    CFLAGS += -DDISASM_INIT_STYLED
+endif
 
 include $(wildcard $(OUTPUT)*.d)
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/btf_dumper.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/btf_dumper.c
@@ -418,7 +418,7 @@
 					     *(char *)data);
 		break;
 	case BTF_INT_BOOL:
-		jsonw_bool(jw, *(int *)data);
+		jsonw_bool(jw, *(bool *)data);
 		break;
 	default:
 		/* shouldn't happen */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/common.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/common.c
@@ -278,6 +278,9 @@
 	int err;
 	int fd;
 
+	if (!REQ_ARGS(3))
+		return -EINVAL;
+
 	fd = get_fd(&argc, &argv);
 	if (fd < 0)
 		return fd;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/feature.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/feature.c
@@ -135,12 +135,12 @@
 
 /* Probing functions */
 
-static int read_procfs(const char *path)
+static long read_procfs(const char *path)
 {
 	char *endptr, *line = NULL;
 	size_t len = 0;
 	FILE *fd;
-	int res;
+	long res;
 
 	fd = fopen(path, "r");
 	if (!fd)
@@ -162,7 +162,7 @@
 
 static void probe_unprivileged_disabled(void)
 {
-	int res;
+	long res;
 
 	/* No support for C-style ouptut */
 
@@ -181,14 +181,14 @@
 			printf("Unable to retrieve required privileges for bpf() syscall\n");
 			break;
 		default:
-			printf("bpf() syscall restriction has unknown value %d\n", res);
+			printf("bpf() syscall restriction has unknown value %ld\n", res);
 		}
 	}
 }
 
 static void probe_jit_enable(void)
 {
-	int res;
+	long res;
 
 	/* No support for C-style ouptut */
 
@@ -210,7 +210,7 @@
 			printf("Unable to retrieve JIT-compiler status\n");
 			break;
 		default:
-			printf("JIT-compiler status has unknown value %d\n",
+			printf("JIT-compiler status has unknown value %ld\n",
 			       res);
 		}
 	}
@@ -218,7 +218,7 @@
 
 static void probe_jit_harden(void)
 {
-	int res;
+	long res;
 
 	/* No support for C-style ouptut */
 
@@ -240,7 +240,7 @@
 			printf("Unable to retrieve JIT hardening status\n");
 			break;
 		default:
-			printf("JIT hardening status has unknown value %d\n",
+			printf("JIT hardening status has unknown value %ld\n",
 			       res);
 		}
 	}
@@ -248,7 +248,7 @@
 
 static void probe_jit_kallsyms(void)
 {
-	int res;
+	long res;
 
 	/* No support for C-style ouptut */
 
@@ -267,14 +267,14 @@
 			printf("Unable to retrieve JIT kallsyms export status\n");
 			break;
 		default:
-			printf("JIT kallsyms exports status has unknown value %d\n", res);
+			printf("JIT kallsyms exports status has unknown value %ld\n", res);
 		}
 	}
 }
 
 static void probe_jit_limit(void)
 {
-	int res;
+	long res;
 
 	/* No support for C-style ouptut */
 
@@ -287,7 +287,7 @@
 			printf("Unable to retrieve global memory limit for JIT compiler for unprivileged users\n");
 			break;
 		default:
-			printf("Global memory limit for JIT compiler for unprivileged users is %d bytes\n", res);
+			printf("Global memory limit for JIT compiler for unprivileged users is %ld bytes\n", res);
 		}
 	}
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/gen.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/gen.c
@@ -870,7 +870,6 @@
 			s = (struct bpf_object_skeleton *)calloc(1, sizeof(*s));\n\
 			if (!s)						    \n\
 				goto err;				    \n\
-			obj->skeleton = s;				    \n\
 									    \n\
 			s->sz = sizeof(*s);				    \n\
 			s->name = \"%1$s\";				    \n\
@@ -955,6 +954,7 @@
 		\n\
 		\";							    \n\
 									    \n\
+			obj->skeleton = s;				    \n\
 			return 0;					    \n\
 		err:							    \n\
 			bpf_object__destroy_skeleton(s);		    \n\
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/jit_disasm.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/jit_disasm.c
@@ -16,7 +16,6 @@
 #include <stdarg.h>
 #include <stdint.h>
 #include <stdlib.h>
-#include <assert.h>
 #include <unistd.h>
 #include <string.h>
 #include <bfd.h>
@@ -24,30 +23,32 @@
 #include <sys/stat.h>
 #include <limits.h>
 #include <bpf/libbpf.h>
+#include <tools/dis-asm-compat.h>
 
 #include "json_writer.h"
 #include "main.h"
 
-static void get_exec_path(char *tpath, size_t size)
+static int get_exec_path(char *tpath, size_t size)
 {
 	const char *path = "/proc/self/exe";
 	ssize_t len;
 
 	len = readlink(path, tpath, size - 1);
-	assert(len > 0);
+	if (len <= 0)
+		return -1;
+
 	tpath[len] = 0;
+
+	return 0;
 }
 
 static int oper_count;
-static int fprintf_json(void *out, const char *fmt, ...)
+static int printf_json(void *out, const char *fmt, va_list ap)
 {
-	va_list ap;
 	char *s;
 	int err;
 
-	va_start(ap, fmt);
 	err = vasprintf(&s, fmt, ap);
-	va_end(ap);
 	if (err < 0)
 		return -1;
 
@@ -73,37 +74,74 @@
 	return 0;
 }
 
-void disasm_print_insn(unsigned char *image, ssize_t len, int opcodes,
-		       const char *arch, const char *disassembler_options,
-		       const struct btf *btf,
-		       const struct bpf_prog_linfo *prog_linfo,
-		       __u64 func_ksym, unsigned int func_idx,
-		       bool linum)
+static int fprintf_json(void *out, const char *fmt, ...)
+{
+	va_list ap;
+	int r;
+
+	va_start(ap, fmt);
+	r = printf_json(out, fmt, ap);
+	va_end(ap);
+
+	return r;
+}
+
+static int fprintf_json_styled(void *out,
+			       enum disassembler_style style __maybe_unused,
+			       const char *fmt, ...)
+{
+	va_list ap;
+	int r;
+
+	va_start(ap, fmt);
+	r = printf_json(out, fmt, ap);
+	va_end(ap);
+
+	return r;
+}
+
+int disasm_print_insn(unsigned char *image, ssize_t len, int opcodes,
+		      const char *arch, const char *disassembler_options,
+		      const struct btf *btf,
+		      const struct bpf_prog_linfo *prog_linfo,
+		      __u64 func_ksym, unsigned int func_idx,
+		      bool linum)
 {
 	const struct bpf_line_info *linfo = NULL;
 	disassembler_ftype disassemble;
+	int count, i, pc = 0, err = -1;
 	struct disassemble_info info;
 	unsigned int nr_skip = 0;
-	int count, i, pc = 0;
 	char tpath[PATH_MAX];
 	bfd *bfdf;
 
 	if (!len)
-		return;
+		return -1;
 
 	memset(tpath, 0, sizeof(tpath));
-	get_exec_path(tpath, sizeof(tpath));
+	if (get_exec_path(tpath, sizeof(tpath))) {
+		p_err("failed to create disasembler (get_exec_path)");
+		return -1;
+	}
 
 	bfdf = bfd_openr(tpath, NULL);
-	assert(bfdf);
-	assert(bfd_check_format(bfdf, bfd_object));
+	if (!bfdf) {
+		p_err("failed to create disassembler (bfd_openr)");
+		return -1;
+	}
+	if (!bfd_check_format(bfdf, bfd_object)) {
+		p_err("failed to create disassembler (bfd_check_format)");
+		goto exit_close;
+	}
 
 	if (json_output)
-		init_disassemble_info(&info, stdout,
-				      (fprintf_ftype) fprintf_json);
+		init_disassemble_info_compat(&info, stdout,
+					     (fprintf_ftype) fprintf_json,
+					     fprintf_json_styled);
 	else
-		init_disassemble_info(&info, stdout,
-				      (fprintf_ftype) fprintf);
+		init_disassemble_info_compat(&info, stdout,
+					     (fprintf_ftype) fprintf,
+					     fprintf_styled);
 
 	/* Update architecture info for offload. */
 	if (arch) {
@@ -113,7 +151,7 @@
 			bfdf->arch_info = inf;
 		} else {
 			p_err("No libbfd support for %s", arch);
-			return;
+			goto exit_close;
 		}
 	}
 
@@ -134,7 +172,10 @@
 #else
 	disassemble = disassembler(bfdf);
 #endif
-	assert(disassemble);
+	if (!disassemble) {
+		p_err("failed to create disassembler");
+		goto exit_close;
+	}
 
 	if (json_output)
 		jsonw_start_array(json_wtr);
@@ -198,7 +239,11 @@
 	if (json_output)
 		jsonw_end_array(json_wtr);
 
+	err = 0;
+
+exit_close:
 	bfd_close(bfdf);
+	return err;
 }
 
 int disasm_init(void)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/json_writer.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/json_writer.c
@@ -80,9 +80,6 @@
 		case '"':
 			fputs("\\\"", self->out);
 			break;
-		case '\'':
-			fputs("\\\'", self->out);
-			break;
 		default:
 			putc(*str, self->out);
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/main.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/main.c
@@ -402,6 +402,18 @@
 	};
 	int opt, ret;
 
+	setlinebuf(stdout);
+
+#ifdef USE_LIBCAP
+	/* Libcap < 2.63 hooks before main() to compute the number of
+	 * capabilities of the running kernel, and doing so it calls prctl()
+	 * which may fail and set errno to non-zero.
+	 * Let's reset errno to make sure this does not interfere with the
+	 * batch mode.
+	 */
+	errno = 0;
+#endif
+
 	last_do_help = do_help;
 	pretty_output = false;
 	json_output = false;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/main.h
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/main.h
@@ -193,22 +193,23 @@
 
 struct bpf_prog_linfo;
 #ifdef HAVE_LIBBFD_SUPPORT
-void disasm_print_insn(unsigned char *image, ssize_t len, int opcodes,
-		       const char *arch, const char *disassembler_options,
-		       const struct btf *btf,
-		       const struct bpf_prog_linfo *prog_linfo,
-		       __u64 func_ksym, unsigned int func_idx,
-		       bool linum);
+int disasm_print_insn(unsigned char *image, ssize_t len, int opcodes,
+		      const char *arch, const char *disassembler_options,
+		      const struct btf *btf,
+		      const struct bpf_prog_linfo *prog_linfo,
+		      __u64 func_ksym, unsigned int func_idx,
+		      bool linum);
 int disasm_init(void);
 #else
 static inline
-void disasm_print_insn(unsigned char *image, ssize_t len, int opcodes,
-		       const char *arch, const char *disassembler_options,
-		       const struct btf *btf,
-		       const struct bpf_prog_linfo *prog_linfo,
-		       __u64 func_ksym, unsigned int func_idx,
-		       bool linum)
+int disasm_print_insn(unsigned char *image, ssize_t len, int opcodes,
+		      const char *arch, const char *disassembler_options,
+		      const struct btf *btf,
+		      const struct bpf_prog_linfo *prog_linfo,
+		      __u64 func_ksym, unsigned int func_idx,
+		      bool linum)
 {
+	return 0;
 }
 static inline int disasm_init(void)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/map.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/map.c
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 /* Copyright (C) 2017-2018 Netronome Systems, Inc. */
 
-#include <assert.h>
 #include <errno.h>
 #include <fcntl.h>
 #include <linux/err.h>
@@ -1042,11 +1041,9 @@
 	json_writer_t *btf_wtr;
 	struct btf *btf;
 
-	btf = btf__load_from_kernel_by_id(info->btf_id);
-	if (libbpf_get_error(btf)) {
-		p_err("failed to get btf");
+	btf = get_map_kv_btf(info);
+	if (libbpf_get_error(btf))
 		return;
-	}
 
 	if (json_output) {
 		print_entry_json(info, key, value, btf);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/prog.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/prog.c
@@ -308,18 +308,12 @@
 		if (printed_header)
 			jsonw_end_object(json_wtr);
 	} else {
-		json_writer_t *btf_wtr = jsonw_new(stdout);
+		json_writer_t *btf_wtr;
 		struct btf_dumper d = {
 			.btf = btf,
-			.jw = btf_wtr,
 			.is_plain_text = true,
 		};
 
-		if (!btf_wtr) {
-			p_err("jsonw alloc failed");
-			goto out_free;
-		}
-
 		for (i = 0; i < vlen; i++, vsi++) {
 			t_var = btf__type_by_id(btf, vsi->type);
 			name = btf__name_by_offset(btf, t_var->name_off);
@@ -329,6 +323,14 @@
 
 			if (!printed_header) {
 				printf("\tmetadata:");
+
+				btf_wtr = jsonw_new(stdout);
+				if (!btf_wtr) {
+					p_err("jsonw alloc failed");
+					goto out_free;
+				}
+				d.jw = btf_wtr,
+
 				printed_header = true;
 			}
 
@@ -627,8 +629,8 @@
 	char func_sig[1024];
 	unsigned char *buf;
 	__u32 member_len;
+	int fd, err = -1;
 	ssize_t n;
-	int fd;
 
 	if (mode == DUMP_JITED) {
 		if (info->jited_prog_len == 0 || !info->jited_prog_insns) {
@@ -667,7 +669,7 @@
 		if (fd < 0) {
 			p_err("can't open file %s: %s", filepath,
 			      strerror(errno));
-			return -1;
+			goto exit_free;
 		}
 
 		n = write(fd, buf, member_len);
@@ -675,7 +677,7 @@
 		if (n != (ssize_t)member_len) {
 			p_err("error writing output file: %s",
 			      n < 0 ? strerror(errno) : "short write");
-			return -1;
+			goto exit_free;
 		}
 
 		if (json_output)
@@ -689,7 +691,7 @@
 						     info->netns_ino,
 						     &disasm_opt);
 			if (!name)
-				return -1;
+				goto exit_free;
 		}
 
 		if (info->nr_jited_func_lens && info->jited_func_lens) {
@@ -742,10 +744,18 @@
 					printf("%s:\n", sym_name);
 				}
 
-				disasm_print_insn(img, lens[i], opcodes,
-						  name, disasm_opt, btf,
-						  prog_linfo, ksyms[i], i,
-						  linum);
+				if (ksyms) {
+					if (disasm_print_insn(img, lens[i], opcodes,
+							      name, disasm_opt, btf,
+							      prog_linfo, ksyms[i], i,
+							      linum))
+						goto exit_free;
+				} else {
+					if (disasm_print_insn(img, lens[i], opcodes,
+							      name, disasm_opt, btf,
+							      NULL, 0, 0, false))
+						goto exit_free;
+				}
 
 				img += lens[i];
 
@@ -758,8 +768,10 @@
 			if (json_output)
 				jsonw_end_array(json_wtr);
 		} else {
-			disasm_print_insn(buf, member_len, opcodes, name,
-					  disasm_opt, btf, NULL, 0, 0, false);
+			if (disasm_print_insn(buf, member_len, opcodes, name,
+					      disasm_opt, btf, NULL, 0, 0,
+					      false))
+				goto exit_free;
 		}
 	} else if (visual) {
 		if (json_output)
@@ -784,9 +796,12 @@
 		kernel_syms_destroy(&dd);
 	}
 
-	btf__free(btf);
+	err = 0;
 
-	return 0;
+exit_free:
+	btf__free(btf);
+	bpf_prog_linfo__free(prog_linfo);
+	return err;
 }
 
 static int do_dump(int argc, char **argv)
@@ -2059,13 +2074,41 @@
 	profile_perf_event_cnt = 0;
 }
 
+static int profile_open_perf_event(int mid, int cpu, int map_fd)
+{
+	int pmu_fd;
+
+	pmu_fd = syscall(__NR_perf_event_open, &metrics[mid].attr,
+			 -1 /*pid*/, cpu, -1 /*group_fd*/, 0);
+	if (pmu_fd < 0) {
+		if (errno == ENODEV) {
+			p_info("cpu %d may be offline, skip %s profiling.",
+				cpu, metrics[mid].name);
+			profile_perf_event_cnt++;
+			return 0;
+		}
+		return -1;
+	}
+
+	if (bpf_map_update_elem(map_fd,
+				&profile_perf_event_cnt,
+				&pmu_fd, BPF_ANY) ||
+	    ioctl(pmu_fd, PERF_EVENT_IOC_ENABLE, 0)) {
+		close(pmu_fd);
+		return -1;
+	}
+
+	profile_perf_events[profile_perf_event_cnt++] = pmu_fd;
+	return 0;
+}
+
 static int profile_open_perf_events(struct profiler_bpf *obj)
 {
 	unsigned int cpu, m;
-	int map_fd, pmu_fd;
+	int map_fd;
 
 	profile_perf_events = calloc(
-		sizeof(int), obj->rodata->num_cpu * obj->rodata->num_metric);
+		obj->rodata->num_cpu * obj->rodata->num_metric, sizeof(int));
 	if (!profile_perf_events) {
 		p_err("failed to allocate memory for perf_event array: %s",
 		      strerror(errno));
@@ -2081,17 +2124,11 @@
 		if (!metrics[m].selected)
 			continue;
 		for (cpu = 0; cpu < obj->rodata->num_cpu; cpu++) {
-			pmu_fd = syscall(__NR_perf_event_open, &metrics[m].attr,
-					 -1/*pid*/, cpu, -1/*group_fd*/, 0);
-			if (pmu_fd < 0 ||
-			    bpf_map_update_elem(map_fd, &profile_perf_event_cnt,
-						&pmu_fd, BPF_ANY) ||
-			    ioctl(pmu_fd, PERF_EVENT_IOC_ENABLE, 0)) {
+			if (profile_open_perf_event(m, cpu, map_fd)) {
 				p_err("failed to create event %s on cpu %d",
 				      metrics[m].name, cpu);
 				return -1;
 			}
-			profile_perf_events[profile_perf_event_cnt++] = pmu_fd;
 		}
 	}
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/skeleton/profiler.bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/skeleton/profiler.bpf.c
@@ -4,6 +4,12 @@
 #include <bpf/bpf_helpers.h>
 #include <bpf/bpf_tracing.h>
 
+struct bpf_perf_event_value___local {
+	__u64 counter;
+	__u64 enabled;
+	__u64 running;
+} __attribute__((preserve_access_index));
+
 /* map of perf event fds, num_cpu * num_metric entries */
 struct {
 	__uint(type, BPF_MAP_TYPE_PERF_EVENT_ARRAY);
@@ -15,14 +21,14 @@
 struct {
 	__uint(type, BPF_MAP_TYPE_PERCPU_ARRAY);
 	__uint(key_size, sizeof(u32));
-	__uint(value_size, sizeof(struct bpf_perf_event_value));
+	__uint(value_size, sizeof(struct bpf_perf_event_value___local));
 } fentry_readings SEC(".maps");
 
 /* accumulated readings */
 struct {
 	__uint(type, BPF_MAP_TYPE_PERCPU_ARRAY);
 	__uint(key_size, sizeof(u32));
-	__uint(value_size, sizeof(struct bpf_perf_event_value));
+	__uint(value_size, sizeof(struct bpf_perf_event_value___local));
 } accum_readings SEC(".maps");
 
 /* sample counts, one per cpu */
@@ -39,7 +45,7 @@
 SEC("fentry/XXX")
 int BPF_PROG(fentry_XXX)
 {
-	struct bpf_perf_event_value *ptrs[MAX_NUM_MATRICS];
+	struct bpf_perf_event_value___local *ptrs[MAX_NUM_MATRICS];
 	u32 key = bpf_get_smp_processor_id();
 	u32 i;
 
@@ -53,10 +59,10 @@
 	}
 
 	for (i = 0; i < num_metric && i < MAX_NUM_MATRICS; i++) {
-		struct bpf_perf_event_value reading;
+		struct bpf_perf_event_value___local reading;
 		int err;
 
-		err = bpf_perf_event_read_value(&events, key, &reading,
+		err = bpf_perf_event_read_value(&events, key, (void *)&reading,
 						sizeof(reading));
 		if (err)
 			return 0;
@@ -68,14 +74,14 @@
 }
 
 static inline void
-fexit_update_maps(u32 id, struct bpf_perf_event_value *after)
+fexit_update_maps(u32 id, struct bpf_perf_event_value___local *after)
 {
-	struct bpf_perf_event_value *before, diff;
+	struct bpf_perf_event_value___local *before, diff;
 
 	before = bpf_map_lookup_elem(&fentry_readings, &id);
 	/* only account samples with a valid fentry_reading */
 	if (before && before->counter) {
-		struct bpf_perf_event_value *accum;
+		struct bpf_perf_event_value___local *accum;
 
 		diff.counter = after->counter - before->counter;
 		diff.enabled = after->enabled - before->enabled;
@@ -93,7 +99,7 @@
 SEC("fexit/XXX")
 int BPF_PROG(fexit_XXX)
 {
-	struct bpf_perf_event_value readings[MAX_NUM_MATRICS];
+	struct bpf_perf_event_value___local readings[MAX_NUM_MATRICS];
 	u32 cpu = bpf_get_smp_processor_id();
 	u32 i, zero = 0;
 	int err;
@@ -102,7 +108,8 @@
 	/* read all events before updating the maps, to reduce error */
 	for (i = 0; i < num_metric && i < MAX_NUM_MATRICS; i++) {
 		err = bpf_perf_event_read_value(&events, cpu + i * num_cpu,
-						readings + i, sizeof(*readings));
+						(void *)(readings + i),
+						sizeof(*readings));
 		if (err)
 			return 0;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/bpftool/xlated_dumper.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/bpftool/xlated_dumper.c
@@ -369,8 +369,15 @@
 	struct bpf_insn *insn_start = buf_start;
 	struct bpf_insn *insn_end = buf_end;
 	struct bpf_insn *cur = insn_start;
+	bool double_insn = false;
 
 	for (; cur <= insn_end; cur++) {
+		if (double_insn) {
+			double_insn = false;
+			continue;
+		}
+		double_insn = cur->code == (BPF_LD | BPF_IMM | BPF_DW);
+
 		printf("% 4d: ", (int)(cur - insn_start + start_idx));
 		print_bpf_insn(&cbs, cur, true);
 		if (cur != insn_end)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/resolve_btfids/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/resolve_btfids/Makefile
@@ -9,7 +9,11 @@
   msg =
 else
   Q = @
-  msg = @printf '  %-8s %s%s\n' "$(1)" "$(notdir $(2))" "$(if $(3), $(3))";
+  ifeq ($(silent),1)
+    msg =
+  else
+    msg = @printf '  %-8s %s%s\n' "$(1)" "$(notdir $(2))" "$(if $(3), $(3))";
+  endif
   MAKEFLAGS=--no-print-directory
 endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/bpf/resolve_btfids/main.c
+++ linux-xilinx-zynqmp-5.15.0/tools/bpf/resolve_btfids/main.c
@@ -166,7 +166,7 @@
 	return NULL;
 }
 
-static struct btf_id*
+static struct btf_id *
 btf_id__add(struct rb_root *root, char *name, bool unique)
 {
 	struct rb_node **p = &root->rb_node;
@@ -643,7 +643,7 @@
 
 static int symbols_patch(struct object *obj)
 {
-	int err;
+	off_t err;
 
 	if (__symbols_patch(obj, &obj->structs)  ||
 	    __symbols_patch(obj, &obj->unions)   ||
@@ -720,7 +720,8 @@
 		if (no_fail)
 			return 0;
 		pr_err("FAILED to find needed sections\n");
-		return -1;
+		err = 0;
+		goto out;
 	}
 
 	if (symbols_collect(&obj))
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/Makefile.feature
+++ linux-xilinx-zynqmp-5.15.0/tools/build/Makefile.feature
@@ -48,7 +48,6 @@
         numa_num_possible_cpus          \
         libperl                         \
         libpython                       \
-        libpython-version               \
         libslang                        \
         libslang-include-subdir         \
         libtraceevent                   \
@@ -70,6 +69,7 @@
         libaio				\
         libzstd				\
         disassembler-four-args		\
+        disassembler-init-styled	\
         file-handle
 
 # FEATURE_TESTS_BASIC + FEATURE_TESTS_EXTRA is the complete list
@@ -98,6 +98,7 @@
          llvm-version                   \
          clang                          \
          libbpf                         \
+         libbpf-btf__load_from_kernel_by_id \
          libpfm4                        \
          libdebuginfod			\
          clang-bpf-co-re
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/feature/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/build/feature/Makefile
@@ -18,6 +18,7 @@
          test-libbfd.bin                        \
          test-libbfd-buildid.bin		\
          test-disassembler-four-args.bin        \
+         test-disassembler-init-styled.bin	\
          test-reallocarray.bin			\
          test-libbfd-liberty.bin                \
          test-libbfd-liberty-z.bin              \
@@ -32,7 +33,6 @@
          test-numa_num_possible_cpus.bin        \
          test-libperl.bin                       \
          test-libpython.bin                     \
-         test-libpython-version.bin             \
          test-libslang.bin                      \
          test-libslang-include-subdir.bin       \
          test-libtraceevent.bin                 \
@@ -57,6 +57,7 @@
          test-lzma.bin                          \
          test-bpf.bin                           \
          test-libbpf.bin                        \
+         test-libbpf-btf__load_from_kernel_by_id.bin	\
          test-get_cpuid.bin                     \
          test-sdt.bin                           \
          test-cxx.bin                           \
@@ -214,18 +215,22 @@
 PERL_EMBED_LDOPTS = $(shell perl -MExtUtils::Embed -e ldopts 2>/dev/null)
 PERL_EMBED_LDFLAGS = $(call strip-libs,$(PERL_EMBED_LDOPTS))
 PERL_EMBED_LIBADD = $(call grep-libs,$(PERL_EMBED_LDOPTS))
-PERL_EMBED_CCOPTS = `perl -MExtUtils::Embed -e ccopts 2>/dev/null`
+PERL_EMBED_CCOPTS = $(shell perl -MExtUtils::Embed -e ccopts 2>/dev/null)
 FLAGS_PERL_EMBED=$(PERL_EMBED_CCOPTS) $(PERL_EMBED_LDOPTS)
 
+ifeq ($(CC_NO_CLANG), 0)
+  PERL_EMBED_LDOPTS := $(filter-out -specs=%,$(PERL_EMBED_LDOPTS))
+  PERL_EMBED_CCOPTS := $(filter-out -flto=auto -ffat-lto-objects, $(PERL_EMBED_CCOPTS))
+  PERL_EMBED_CCOPTS := $(filter-out -specs=%,$(PERL_EMBED_CCOPTS))
+  FLAGS_PERL_EMBED += -Wno-compound-token-split-by-macro
+endif
+
 $(OUTPUT)test-libperl.bin:
 	$(BUILD) $(FLAGS_PERL_EMBED)
 
 $(OUTPUT)test-libpython.bin:
 	$(BUILD) $(FLAGS_PYTHON_EMBED)
 
-$(OUTPUT)test-libpython-version.bin:
-	$(BUILD)
-
 $(OUTPUT)test-libbfd.bin:
 	$(BUILD) -DPACKAGE='"perf"' -lbfd -ldl
 
@@ -235,6 +240,9 @@
 $(OUTPUT)test-disassembler-four-args.bin:
 	$(BUILD) -DPACKAGE='"perf"' -lbfd -lopcodes
 
+$(OUTPUT)test-disassembler-init-styled.bin:
+	$(BUILD) -DPACKAGE='"perf"' -lbfd -lopcodes
+
 $(OUTPUT)test-reallocarray.bin:
 	$(BUILD)
 
@@ -280,6 +288,9 @@
 $(OUTPUT)test-libbpf.bin:
 	$(BUILD) -lbpf
 
+$(OUTPUT)test-libbpf-btf__load_from_kernel_by_id.bin:
+	$(BUILD) -lbpf
+
 $(OUTPUT)test-sdt.bin:
 	$(BUILD)
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/feature/test-all.c
+++ linux-xilinx-zynqmp-5.15.0/tools/build/feature/test-all.c
@@ -14,10 +14,6 @@
 # include "test-libpython.c"
 #undef main
 
-#define main main_test_libpython_version
-# include "test-libpython-version.c"
-#undef main
-
 #define main main_test_libperl
 # include "test-libperl.c"
 #undef main
@@ -170,6 +166,10 @@
 # include "test-disassembler-four-args.c"
 #undef main
 
+#define main main_test_disassembler_init_styled
+# include "test-disassembler-init-styled.c"
+#undef main
+
 #define main main_test_libzstd
 # include "test-libzstd.c"
 #undef main
@@ -177,7 +177,6 @@
 int main(int argc, char *argv[])
 {
 	main_test_libpython();
-	main_test_libpython_version();
 	main_test_libperl();
 	main_test_hello();
 	main_test_libelf();
@@ -200,7 +199,6 @@
 	main_test_timerfd();
 	main_test_stackprotector_all();
 	main_test_libdw_dwarf_unwind();
-	main_test_sync_compare_and_swap(argc, argv);
 	main_test_zlib();
 	main_test_pthread_attr_setaffinity_np();
 	main_test_pthread_barrier();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/feature/test-disassembler-init-styled.c
+++ linux-xilinx-zynqmp-5.15.0/tools/build/feature/test-disassembler-init-styled.c
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <stdio.h>
+#include <dis-asm.h>
+
+int main(void)
+{
+	struct disassemble_info info;
+
+	init_disassemble_info(&info, stdout,
+			      NULL, NULL);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/feature/test-libbpf-btf__load_from_kernel_by_id.c
+++ linux-xilinx-zynqmp-5.15.0/tools/build/feature/test-libbpf-btf__load_from_kernel_by_id.c
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <bpf/btf.h>
+
+int main(void)
+{
+	btf__load_from_kernel_by_id(20151128);
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/feature/test-libcrypto.c
+++ linux-xilinx-zynqmp-5.15.0/tools/build/feature/test-libcrypto.c
@@ -1,16 +1,23 @@
 // SPDX-License-Identifier: GPL-2.0
+#include <openssl/evp.h>
 #include <openssl/sha.h>
 #include <openssl/md5.h>
 
 int main(void)
 {
-	MD5_CTX context;
+	EVP_MD_CTX *mdctx;
 	unsigned char md[MD5_DIGEST_LENGTH + SHA_DIGEST_LENGTH];
 	unsigned char dat[] = "12345";
+	unsigned int digest_len;
 
-	MD5_Init(&context);
-	MD5_Update(&context, &dat[0], sizeof(dat));
-	MD5_Final(&md[0], &context);
+	mdctx = EVP_MD_CTX_new();
+	if (!mdctx)
+		return 0;
+
+	EVP_DigestInit_ex(mdctx, EVP_md5(), NULL);
+	EVP_DigestUpdate(mdctx, &dat[0], sizeof(dat));
+	EVP_DigestFinal_ex(mdctx, &md[0], &digest_len);
+	EVP_MD_CTX_free(mdctx);
 
 	SHA1(&dat[0], sizeof(dat), &md[0]);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/build/feature/test-libopencsd.c
+++ linux-xilinx-zynqmp-5.15.0/tools/build/feature/test-libopencsd.c
@@ -4,9 +4,9 @@
 /*
  * Check OpenCSD library version is sufficient to provide required features
  */
-#define OCSD_MIN_VER ((1 << 16) | (1 << 8) | (1))
+#define OCSD_MIN_VER ((1 << 16) | (2 << 8) | (1))
 #if !defined(OCSD_VER_NUM) || (OCSD_VER_NUM < OCSD_MIN_VER)
-#error "OpenCSD >= 1.1.1 is required"
+#error "OpenCSD >= 1.2.1 is required"
 #endif
 
 int main(void)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/gpio/gpio-event-mon.c
+++ linux-xilinx-zynqmp-5.15.0/tools/gpio/gpio-event-mon.c
@@ -86,6 +86,7 @@
 			gpiotools_test_bit(values.bits, i));
 	}
 
+	i = 0;
 	while (1) {
 		struct gpio_v2_line_event event;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/gpio/lsgpio.c
+++ linux-xilinx-zynqmp-5.15.0/tools/gpio/lsgpio.c
@@ -94,7 +94,7 @@
 	for (i = 0; i < info->num_attrs; i++) {
 		if (info->attrs[i].id == GPIO_V2_LINE_ATTR_ID_DEBOUNCE)
 			fprintf(stdout, ", debounce_period=%dusec",
-				info->attrs[0].debounce_period_us);
+				info->attrs[i].debounce_period_us);
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/hv/hv_kvp_daemon.8
+++ linux-xilinx-zynqmp-5.15.0/tools/hv/hv_kvp_daemon.8
@@ -0,0 +1,26 @@
+.\"  This page Copyright (C) 2012 Andy Whitcroft <apw@canonical.com>
+.\"  Distributed under the GPL v2 or later.
+.TH HV_KVP_DAEMON 8
+.SH NAME
+hv_kvp_daemon \- Hyper-V Key Value Pair daemon
+.SH SYNOPSIS
+.ft B
+.B hv_kvp_daemon
+.br
+.SH DESCRIPTION
+\fBhv_kvp_daemon\fP
+is the userspace component of the Hyper-V key value pair functionality,
+communicating via a netlink socket with the kernel HV-KVP driver.
+This pairing allows the Hyper-V host to pass configuration information
+(such as IP addresses) to the guest and allows the host to obtain guest
+version information.
+
+.SH FILES
+.ta
+.nf
+/var/opt/hyperv/.kvp_pool_*
+.fi
+
+.SH AUTHORS
+.nf
+Written by K. Y. Srinivasan <ksrinivasan@novell.com>
--- linux-xilinx-zynqmp-5.15.0.orig/tools/hv/lsvmbus
+++ linux-xilinx-zynqmp-5.15.0/tools/hv/lsvmbus
@@ -1,4 +1,4 @@
-#!/usr/bin/env python
+#!/usr/bin/env python3
 # SPDX-License-Identifier: GPL-2.0
 
 import os
--- linux-xilinx-zynqmp-5.15.0.orig/tools/hv/lsvmbus.8
+++ linux-xilinx-zynqmp-5.15.0/tools/hv/lsvmbus.8
@@ -0,0 +1,23 @@
+.\"  This page Copyright (C) 2016 Andy Whitcroft <apw@canonical.com>
+.\"  Distributed under the GPL v2 or later.
+.TH LSVMBUS 8
+.SH NAME
+lsvmbus \- List Hyper-V VMBus devices
+.SH SYNOPSIS
+.ft B
+.B lsvmbus [-vv]
+.br
+.SH DESCRIPTION
+\fBlsvmbus\fP
+displays devices attached to the Hyper-V VMBus.
+.SH OPTIONS
+.\"
+.TP
+.B -v
+With -v more information is printed including the VMBus Rel_ID, class ID,
+Rel_ID, and which channel is bound to which virtual processor.  Use -vv
+for additional detail including the Device_ID and the sysfs path.
+.\"
+.SH AUTHORS
+.nf
+Written by Dexuan Cui <decui@microsoft.com>
--- linux-xilinx-zynqmp-5.15.0.orig/tools/hv/vmbus_testing
+++ linux-xilinx-zynqmp-5.15.0/tools/hv/vmbus_testing
@@ -164,7 +164,7 @@
 def get_all_devices_test_status(file_map):
 
         for device in file_map:
-                if (get_test_state(locate_state(device, file_map)) is 1):
+                if (get_test_state(locate_state(device, file_map)) == 1):
                         print("Testing = ON for: {}"
                               .format(device.split("/")[5]))
                 else:
@@ -203,7 +203,7 @@
 def set_test_state(state_path, state_value, quiet):
 
         write_test_files(state_path, state_value)
-        if (get_test_state(state_path) is 1):
+        if (get_test_state(state_path) == 1):
                 if (not quiet):
                         print("Testing = ON for device: {}"
                               .format(state_path.split("/")[5]))
--- linux-xilinx-zynqmp-5.15.0.orig/tools/iio/iio_generic_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/tools/iio/iio_generic_buffer.c
@@ -51,12 +51,15 @@
  * Has the side effect of filling the channels[i].location values used
  * in processing the buffer output.
  **/
-static int size_from_channelarray(struct iio_channel_info *channels, int num_channels)
+static unsigned int size_from_channelarray(struct iio_channel_info *channels, int num_channels)
 {
-	int bytes = 0;
-	int i = 0;
+	unsigned int bytes = 0;
+	int i = 0, max = 0;
+	unsigned int misalignment;
 
 	while (i < num_channels) {
+		if (channels[i].bytes > max)
+			max = channels[i].bytes;
 		if (bytes % channels[i].bytes == 0)
 			channels[i].location = bytes;
 		else
@@ -66,6 +69,14 @@
 		bytes = channels[i].location + channels[i].bytes;
 		i++;
 	}
+	/*
+	 * We want the data in next sample to also be properly aligned so
+	 * we'll add padding at the end if needed. Adding padding only
+	 * works for channel data which size is 2^n bytes.
+	 */
+	misalignment = bytes % max;
+	if (misalignment)
+		bytes += max - misalignment;
 
 	return bytes;
 }
@@ -348,7 +359,7 @@
 	ssize_t read_size;
 	int dev_num = -1, trig_num = -1;
 	char *buffer_access = NULL;
-	int scan_size;
+	unsigned int scan_size;
 	int noevents = 0;
 	int notrigger = 0;
 	char *dummy;
@@ -487,6 +498,10 @@
 			return -ENOMEM;
 		}
 		trigger_name = malloc(IIO_MAX_NAME_LENGTH);
+		if (!trigger_name) {
+			ret = -ENOMEM;
+			goto error;
+		}
 		ret = read_sysfs_string("name", trig_dev_name, trigger_name);
 		free(trig_dev_name);
 		if (ret < 0) {
@@ -674,7 +689,16 @@
 	}
 
 	scan_size = size_from_channelarray(channels, num_channels);
-	data = malloc(scan_size * buf_len);
+
+	size_t total_buf_len = scan_size * buf_len;
+
+	if (scan_size > 0 && total_buf_len / scan_size != buf_len) {
+		ret = -EFAULT;
+		perror("Integer overflow happened when calculate scan_size * buf_len");
+		goto error;
+	}
+
+	data = malloc(total_buf_len);
 	if (!data) {
 		ret = -ENOMEM;
 		goto error;
@@ -715,12 +739,12 @@
 				continue;
 			}
 
-			toread = buf_len;
 		} else {
 			usleep(timedelay);
-			toread = 64;
 		}
 
+		toread = buf_len;
+
 		read_size = read(buf_fd, data, toread * scan_size);
 		if (read_size < 0) {
 			if (errno == EAGAIN) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/iio/iio_utils.c
+++ linux-xilinx-zynqmp-5.15.0/tools/iio/iio_utils.c
@@ -264,6 +264,7 @@
 			if (fscanf(sysfsfp, "%f", output) != 1)
 				ret = errno ? -errno : -ENODATA;
 
+			fclose(sysfsfp);
 			break;
 		}
 error_free_filename:
@@ -345,9 +346,9 @@
 			}
 
 			sysfsfp = fopen(filename, "r");
+			free(filename);
 			if (!sysfsfp) {
 				ret = -errno;
-				free(filename);
 				goto error_close_dir;
 			}
 
@@ -357,7 +358,6 @@
 				if (fclose(sysfsfp))
 					perror("build_channel_array(): Failed to close file");
 
-				free(filename);
 				goto error_close_dir;
 			}
 			if (ret == 1)
@@ -365,11 +365,9 @@
 
 			if (fclose(sysfsfp)) {
 				ret = -errno;
-				free(filename);
 				goto error_close_dir;
 			}
 
-			free(filename);
 		}
 
 	*ci_array = malloc(sizeof(**ci_array) * (*counter));
@@ -378,7 +376,7 @@
 		goto error_close_dir;
 	}
 
-	seekdir(dp, 0);
+	rewinddir(dp);
 	while (ent = readdir(dp), ent) {
 		if (strcmp(ent->d_name + strlen(ent->d_name) - strlen("_en"),
 			   "_en") == 0) {
@@ -395,9 +393,9 @@
 			}
 
 			sysfsfp = fopen(filename, "r");
+			free(filename);
 			if (!sysfsfp) {
 				ret = -errno;
-				free(filename);
 				count--;
 				goto error_cleanup_array;
 			}
@@ -405,20 +403,17 @@
 			errno = 0;
 			if (fscanf(sysfsfp, "%i", &current_enabled) != 1) {
 				ret = errno ? -errno : -ENODATA;
-				free(filename);
 				count--;
 				goto error_cleanup_array;
 			}
 
 			if (fclose(sysfsfp)) {
 				ret = -errno;
-				free(filename);
 				count--;
 				goto error_cleanup_array;
 			}
 
 			if (!current_enabled) {
-				free(filename);
 				count--;
 				continue;
 			}
@@ -429,7 +424,6 @@
 						strlen(ent->d_name) -
 						strlen("_en"));
 			if (!current->name) {
-				free(filename);
 				ret = -ENOMEM;
 				count--;
 				goto error_cleanup_array;
@@ -439,7 +433,6 @@
 			ret = iioutils_break_up_name(current->name,
 						     &current->generic_name);
 			if (ret) {
-				free(filename);
 				free(current->name);
 				count--;
 				goto error_cleanup_array;
@@ -450,17 +443,16 @@
 				       scan_el_dir,
 				       current->name);
 			if (ret < 0) {
-				free(filename);
 				ret = -ENOMEM;
 				goto error_cleanup_array;
 			}
 
 			sysfsfp = fopen(filename, "r");
+			free(filename);
 			if (!sysfsfp) {
 				ret = -errno;
-				fprintf(stderr, "failed to open %s\n",
-					filename);
-				free(filename);
+				fprintf(stderr, "failed to open %s/%s_index\n",
+					scan_el_dir, current->name);
 				goto error_cleanup_array;
 			}
 
@@ -470,17 +462,14 @@
 				if (fclose(sysfsfp))
 					perror("build_channel_array(): Failed to close file");
 
-				free(filename);
 				goto error_cleanup_array;
 			}
 
 			if (fclose(sysfsfp)) {
 				ret = -errno;
-				free(filename);
 				goto error_cleanup_array;
 			}
 
-			free(filename);
 			/* Find the scale */
 			ret = iioutils_get_param_float(&current->scale,
 						       "scale",
@@ -547,6 +536,10 @@
 {
 	int count = 0;
 
+	/* It takes a digit to represent zero */
+	if (!num)
+		return 1;
+
 	while (num != 0) {
 		num /= 10;
 		count++;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/asm-generic/hugetlb_encode.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/asm-generic/hugetlb_encode.h
@@ -20,18 +20,18 @@
 #define HUGETLB_FLAG_ENCODE_SHIFT	26
 #define HUGETLB_FLAG_ENCODE_MASK	0x3f
 
-#define HUGETLB_FLAG_ENCODE_16KB	(14 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_64KB	(16 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_512KB	(19 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_1MB		(20 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_2MB		(21 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_8MB		(23 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_16MB	(24 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_32MB	(25 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_256MB	(28 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_512MB	(29 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_1GB		(30 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_2GB		(31 << HUGETLB_FLAG_ENCODE_SHIFT)
-#define HUGETLB_FLAG_ENCODE_16GB	(34 << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_16KB	(14U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_64KB	(16U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_512KB	(19U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_1MB		(20U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_2MB		(21U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_8MB		(23U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_16MB	(24U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_32MB	(25U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_256MB	(28U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_512MB	(29U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_1GB		(30U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_2GB		(31U << HUGETLB_FLAG_ENCODE_SHIFT)
+#define HUGETLB_FLAG_ENCODE_16GB	(34U << HUGETLB_FLAG_ENCODE_SHIFT)
 
 #endif /* _ASM_GENERIC_HUGETLB_ENCODE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/asm-generic/unaligned.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/asm-generic/unaligned.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copied from the kernel sources to tools/perf/:
+ */
+
+#ifndef __TOOLS_LINUX_ASM_GENERIC_UNALIGNED_H
+#define __TOOLS_LINUX_ASM_GENERIC_UNALIGNED_H
+
+#define __get_unaligned_t(type, ptr) ({						\
+	const struct { type x; } __packed *__pptr = (typeof(__pptr))(ptr);	\
+	__pptr->x;								\
+})
+
+#define __put_unaligned_t(type, val, ptr) do {					\
+	struct { type x; } __packed *__pptr = (typeof(__pptr))(ptr);		\
+	__pptr->x = (val);							\
+} while (0)
+
+#define get_unaligned(ptr)	__get_unaligned_t(typeof(*(ptr)), (ptr))
+#define put_unaligned(val, ptr) __put_unaligned_t(typeof(*(ptr)), (val), (ptr))
+
+#endif /* __TOOLS_LINUX_ASM_GENERIC_UNALIGNED_H */
+
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/linux/align.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/linux/align.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _TOOLS_LINUX_ALIGN_H
+#define _TOOLS_LINUX_ALIGN_H
+
+#include <uapi/linux/const.h>
+
+#define ALIGN(x, a)		__ALIGN_KERNEL((x), (a))
+#define ALIGN_DOWN(x, a)	__ALIGN_KERNEL((x) - ((a) - 1), (a))
+#define IS_ALIGNED(x, a)	(((x) & ((typeof(x))(a) - 1)) == 0)
+
+#endif /* _TOOLS_LINUX_ALIGN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/linux/bitmap.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/linux/bitmap.h
@@ -3,6 +3,7 @@
 #define _PERF_BITOPS_H
 
 #include <string.h>
+#include <linux/align.h>
 #include <linux/bitops.h>
 #include <stdlib.h>
 #include <linux/kernel.h>
@@ -24,13 +25,14 @@
 #define BITMAP_FIRST_WORD_MASK(start) (~0UL << ((start) & (BITS_PER_LONG - 1)))
 #define BITMAP_LAST_WORD_MASK(nbits) (~0UL >> (-(nbits) & (BITS_PER_LONG - 1)))
 
+#define bitmap_size(nbits)	(ALIGN(nbits, BITS_PER_LONG) / BITS_PER_BYTE)
+
 static inline void bitmap_zero(unsigned long *dst, unsigned int nbits)
 {
 	if (small_const_nbits(nbits))
 		*dst = 0UL;
 	else {
-		int len = BITS_TO_LONGS(nbits) * sizeof(unsigned long);
-		memset(dst, 0, len);
+		memset(dst, 0, bitmap_size(nbits));
 	}
 }
 
@@ -116,7 +118,7 @@
  */
 static inline unsigned long *bitmap_zalloc(int nbits)
 {
-	return calloc(1, BITS_TO_LONGS(nbits) * sizeof(unsigned long));
+	return calloc(1, bitmap_size(nbits));
 }
 
 /*
@@ -159,7 +161,6 @@
 #define BITMAP_MEM_ALIGNMENT (8 * sizeof(unsigned long))
 #endif
 #define BITMAP_MEM_MASK (BITMAP_MEM_ALIGNMENT - 1)
-#define IS_ALIGNED(x, a) (((x) & ((typeof(x))(a) - 1)) == 0)
 
 static inline int bitmap_equal(const unsigned long *src1,
 			const unsigned long *src2, unsigned int nbits)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/linux/btf_ids.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/linux/btf_ids.h
@@ -38,7 +38,7 @@
 	____BTF_ID(symbol)
 
 #define __ID(prefix) \
-	__PASTE(prefix, __COUNTER__)
+	__PASTE(__PASTE(prefix, __COUNTER__), __LINE__)
 
 /*
  * The BTF_ID defines unique symbol for each ID pointing
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/linux/kernel.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/linux/kernel.h
@@ -14,6 +14,8 @@
 #define UINT_MAX	(~0U)
 #endif
 
+#define _RET_IP_		((unsigned long)__builtin_return_address(0))
+
 #define DIV_ROUND_UP(n,d) (((n) + (d) - 1) / (d))
 
 #define PERF_ALIGN(x, a)	__PERF_ALIGN_MASK(x, (typeof(x))(a)-1)
@@ -52,6 +54,10 @@
 	_min1 < _min2 ? _min1 : _min2; })
 #endif
 
+#define max_t(type, x, y)	max((type)x, (type)y)
+#define min_t(type, x, y)	min((type)x, (type)y)
+#define clamp(val, lo, hi)	min((typeof(val))max(val, lo), hi)
+
 #ifndef roundup
 #define roundup(x, y) (                                \
 {                                                      \
@@ -102,7 +108,9 @@
 int scnprintf(char * buf, size_t size, const char * fmt, ...);
 int scnprintf_pad(char * buf, size_t size, const char * fmt, ...);
 
+#ifndef ARRAY_SIZE
 #define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]) + __must_be_array(arr))
+#endif
 
 /*
  * This looks more complex than it should be. But we need to
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/linux/objtool.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/linux/objtool.h
@@ -32,11 +32,16 @@
  *
  * UNWIND_HINT_FUNC: Generate the unwind metadata of a callable function.
  * Useful for code which doesn't have an ELF function annotation.
+ *
+ * UNWIND_HINT_ENTRY: machine entry without stack, SYSCALL/SYSENTER etc.
  */
 #define UNWIND_HINT_TYPE_CALL		0
 #define UNWIND_HINT_TYPE_REGS		1
 #define UNWIND_HINT_TYPE_REGS_PARTIAL	2
 #define UNWIND_HINT_TYPE_FUNC		3
+#define UNWIND_HINT_TYPE_ENTRY		4
+#define UNWIND_HINT_TYPE_SAVE		5
+#define UNWIND_HINT_TYPE_RESTORE	6
 
 #ifdef CONFIG_STACK_VALIDATION
 
@@ -66,6 +71,23 @@
 	static void __used __section(".discard.func_stack_frame_non_standard") \
 		*__func_stack_frame_non_standard_##func = func
 
+/*
+ * STACK_FRAME_NON_STANDARD_FP() is a frame-pointer-specific function ignore
+ * for the case where a function is intentionally missing frame pointer setup,
+ * but otherwise needs objtool/ORC coverage when frame pointers are disabled.
+ */
+#ifdef CONFIG_FRAME_POINTER
+#define STACK_FRAME_NON_STANDARD_FP(func) STACK_FRAME_NON_STANDARD(func)
+#else
+#define STACK_FRAME_NON_STANDARD_FP(func)
+#endif
+
+#define ANNOTATE_NOENDBR					\
+	"986: \n\t"						\
+	".pushsection .discard.noendbr\n\t"			\
+	_ASM_PTR " 986b\n\t"					\
+	".popsection\n\t"
+
 #else /* __ASSEMBLY__ */
 
 /*
@@ -99,7 +121,7 @@
  * the debuginfo as necessary.  It will also warn if it sees any
  * inconsistencies.
  */
-.macro UNWIND_HINT sp_reg:req sp_offset=0 type:req end=0
+.macro UNWIND_HINT type:req sp_reg=0 sp_offset=0 end=0
 .Lunwind_hint_ip_\@:
 	.pushsection .discard.unwind_hints
 		/* struct unwind_hint */
@@ -118,6 +140,13 @@
 	.popsection
 .endm
 
+.macro ANNOTATE_NOENDBR
+.Lhere_\@:
+	.pushsection .discard.noendbr
+	.quad	.Lhere_\@
+	.popsection
+.endm
+
 #endif /* __ASSEMBLY__ */
 
 #else /* !CONFIG_STACK_VALIDATION */
@@ -127,12 +156,16 @@
 #define UNWIND_HINT(sp_reg, sp_offset, type, end)	\
 	"\n\t"
 #define STACK_FRAME_NON_STANDARD(func)
+#define STACK_FRAME_NON_STANDARD_FP(func)
+#define ANNOTATE_NOENDBR
 #else
 #define ANNOTATE_INTRA_FUNCTION_CALL
-.macro UNWIND_HINT sp_reg:req sp_offset=0 type:req end=0
+.macro UNWIND_HINT type:req sp_reg=0 sp_offset=0 end=0
 .endm
 .macro STACK_FRAME_NON_STANDARD func:req
 .endm
+.macro ANNOTATE_NOENDBR
+.endm
 #endif
 
 #endif /* CONFIG_STACK_VALIDATION */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch-aarch64.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch-aarch64.h
@@ -0,0 +1,199 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * AARCH64 specific definitions for NOLIBC
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_ARCH_AARCH64_H
+#define _NOLIBC_ARCH_AARCH64_H
+
+/* O_* macros for fcntl/open are architecture-specific */
+#define O_RDONLY            0
+#define O_WRONLY            1
+#define O_RDWR              2
+#define O_CREAT          0x40
+#define O_EXCL           0x80
+#define O_NOCTTY        0x100
+#define O_TRUNC         0x200
+#define O_APPEND        0x400
+#define O_NONBLOCK      0x800
+#define O_DIRECTORY    0x4000
+
+/* The struct returned by the newfstatat() syscall. Differs slightly from the
+ * x86_64's stat one by field ordering, so be careful.
+ */
+struct sys_stat_struct {
+	unsigned long   st_dev;
+	unsigned long   st_ino;
+	unsigned int    st_mode;
+	unsigned int    st_nlink;
+	unsigned int    st_uid;
+	unsigned int    st_gid;
+
+	unsigned long   st_rdev;
+	unsigned long   __pad1;
+	long            st_size;
+	int             st_blksize;
+	int             __pad2;
+
+	long            st_blocks;
+	long            st_atime;
+	unsigned long   st_atime_nsec;
+	long            st_mtime;
+
+	unsigned long   st_mtime_nsec;
+	long            st_ctime;
+	unsigned long   st_ctime_nsec;
+	unsigned int    __unused[2];
+};
+
+/* Syscalls for AARCH64 :
+ *   - registers are 64-bit
+ *   - stack is 16-byte aligned
+ *   - syscall number is passed in x8
+ *   - arguments are in x0, x1, x2, x3, x4, x5
+ *   - the system call is performed by calling svc 0
+ *   - syscall return comes in x0.
+ *   - the arguments are cast to long and assigned into the target registers
+ *     which are then simply passed as registers to the asm code, so that we
+ *     don't have to experience issues with register constraints.
+ *
+ * On aarch64, select() is not implemented so we have to use pselect6().
+ */
+#define __ARCH_WANT_SYS_PSELECT6
+
+#define my_syscall0(num)                                                      \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0");                                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall1(num, arg1)                                                \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0") = (long)(arg1);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1),                                                 \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall2(num, arg1, arg2)                                          \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0") = (long)(arg1);                         \
+	register long _arg2 asm("x1") = (long)(arg2);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1), "r"(_arg2),                                     \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall3(num, arg1, arg2, arg3)                                    \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0") = (long)(arg1);                         \
+	register long _arg2 asm("x1") = (long)(arg2);                         \
+	register long _arg3 asm("x2") = (long)(arg3);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0") = (long)(arg1);                         \
+	register long _arg2 asm("x1") = (long)(arg2);                         \
+	register long _arg3 asm("x2") = (long)(arg3);                         \
+	register long _arg4 asm("x3") = (long)(arg4);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0") = (long)(arg1);                         \
+	register long _arg2 asm("x1") = (long)(arg2);                         \
+	register long _arg3 asm("x2") = (long)(arg3);                         \
+	register long _arg4 asm("x3") = (long)(arg4);                         \
+	register long _arg5 asm("x4") = (long)(arg5);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r" (_arg1)                                                \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall6(num, arg1, arg2, arg3, arg4, arg5, arg6)                  \
+({                                                                            \
+	register long _num  asm("x8") = (num);                                \
+	register long _arg1 asm("x0") = (long)(arg1);                         \
+	register long _arg2 asm("x1") = (long)(arg2);                         \
+	register long _arg3 asm("x2") = (long)(arg3);                         \
+	register long _arg4 asm("x3") = (long)(arg4);                         \
+	register long _arg5 asm("x4") = (long)(arg5);                         \
+	register long _arg6 asm("x5") = (long)(arg6);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r" (_arg1)                                                \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
+		  "r"(_arg6), "r"(_num)                                       \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+/* startup code */
+asm(".section .text\n"
+    ".weak _start\n"
+    "_start:\n"
+    "ldr x0, [sp]\n"              // argc (x0) was in the stack
+    "add x1, sp, 8\n"             // argv (x1) = sp
+    "lsl x2, x0, 3\n"             // envp (x2) = 8*argc ...
+    "add x2, x2, 8\n"             //           + 8 (skip null)
+    "add x2, x2, x1\n"            //           + argv
+    "and sp, x1, -16\n"           // sp must be 16-byte aligned in the callee
+    "bl main\n"                   // main() returns the status code, we'll exit with it.
+    "mov x8, 93\n"                // NR_exit == 93
+    "svc #0\n"
+    "");
+
+#endif // _NOLIBC_ARCH_AARCH64_H
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch-arm.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch-arm.h
@@ -0,0 +1,204 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * ARM specific definitions for NOLIBC
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_ARCH_ARM_H
+#define _NOLIBC_ARCH_ARM_H
+
+/* O_* macros for fcntl/open are architecture-specific */
+#define O_RDONLY            0
+#define O_WRONLY            1
+#define O_RDWR              2
+#define O_CREAT          0x40
+#define O_EXCL           0x80
+#define O_NOCTTY        0x100
+#define O_TRUNC         0x200
+#define O_APPEND        0x400
+#define O_NONBLOCK      0x800
+#define O_DIRECTORY    0x4000
+
+/* The struct returned by the stat() syscall, 32-bit only, the syscall returns
+ * exactly 56 bytes (stops before the unused array). In big endian, the format
+ * differs as devices are returned as short only.
+ */
+struct sys_stat_struct {
+#if defined(__ARMEB__)
+	unsigned short st_dev;
+	unsigned short __pad1;
+#else
+	unsigned long  st_dev;
+#endif
+	unsigned long  st_ino;
+	unsigned short st_mode;
+	unsigned short st_nlink;
+	unsigned short st_uid;
+	unsigned short st_gid;
+
+#if defined(__ARMEB__)
+	unsigned short st_rdev;
+	unsigned short __pad2;
+#else
+	unsigned long  st_rdev;
+#endif
+	unsigned long  st_size;
+	unsigned long  st_blksize;
+	unsigned long  st_blocks;
+
+	unsigned long  st_atime;
+	unsigned long  st_atime_nsec;
+	unsigned long  st_mtime;
+	unsigned long  st_mtime_nsec;
+
+	unsigned long  st_ctime;
+	unsigned long  st_ctime_nsec;
+	unsigned long  __unused[2];
+};
+
+/* Syscalls for ARM in ARM or Thumb modes :
+ *   - registers are 32-bit
+ *   - stack is 8-byte aligned
+ *     ( http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.faqs/ka4127.html)
+ *   - syscall number is passed in r7
+ *   - arguments are in r0, r1, r2, r3, r4, r5
+ *   - the system call is performed by calling svc #0
+ *   - syscall return comes in r0.
+ *   - only lr is clobbered.
+ *   - the arguments are cast to long and assigned into the target registers
+ *     which are then simply passed as registers to the asm code, so that we
+ *     don't have to experience issues with register constraints.
+ *   - the syscall number is always specified last in order to allow to force
+ *     some registers before (gcc refuses a %-register at the last position).
+ *
+ * Also, ARM supports the old_select syscall if newselect is not available
+ */
+#define __ARCH_WANT_SYS_OLD_SELECT
+
+#define my_syscall0(num)                                                      \
+({                                                                            \
+	register long _num asm("r7") = (num);                                 \
+	register long _arg1 asm("r0");                                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_num)                                                   \
+		: "memory", "cc", "lr"                                        \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall1(num, arg1)                                                \
+({                                                                            \
+	register long _num asm("r7") = (num);                                 \
+	register long _arg1 asm("r0") = (long)(arg1);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1),                                                 \
+		  "r"(_num)                                                   \
+		: "memory", "cc", "lr"                                        \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall2(num, arg1, arg2)                                          \
+({                                                                            \
+	register long _num asm("r7") = (num);                                 \
+	register long _arg1 asm("r0") = (long)(arg1);                         \
+	register long _arg2 asm("r1") = (long)(arg2);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1), "r"(_arg2),                                     \
+		  "r"(_num)                                                   \
+		: "memory", "cc", "lr"                                        \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall3(num, arg1, arg2, arg3)                                    \
+({                                                                            \
+	register long _num asm("r7") = (num);                                 \
+	register long _arg1 asm("r0") = (long)(arg1);                         \
+	register long _arg2 asm("r1") = (long)(arg2);                         \
+	register long _arg3 asm("r2") = (long)(arg3);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
+		  "r"(_num)                                                   \
+		: "memory", "cc", "lr"                                        \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
+({                                                                            \
+	register long _num asm("r7") = (num);                                 \
+	register long _arg1 asm("r0") = (long)(arg1);                         \
+	register long _arg2 asm("r1") = (long)(arg2);                         \
+	register long _arg3 asm("r2") = (long)(arg3);                         \
+	register long _arg4 asm("r3") = (long)(arg4);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r"(_arg1)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
+		  "r"(_num)                                                   \
+		: "memory", "cc", "lr"                                        \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
+({                                                                            \
+	register long _num asm("r7") = (num);                                 \
+	register long _arg1 asm("r0") = (long)(arg1);                         \
+	register long _arg2 asm("r1") = (long)(arg2);                         \
+	register long _arg3 asm("r2") = (long)(arg3);                         \
+	register long _arg4 asm("r3") = (long)(arg4);                         \
+	register long _arg5 asm("r4") = (long)(arg5);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"svc #0\n"                                                    \
+		: "=r" (_arg1)                                                \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
+		  "r"(_num)                                                   \
+		: "memory", "cc", "lr"                                        \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+/* startup code */
+asm(".section .text\n"
+    ".weak _start\n"
+    "_start:\n"
+#if defined(__THUMBEB__) || defined(__THUMBEL__)
+    /* We enter here in 32-bit mode but if some previous functions were in
+     * 16-bit mode, the assembler cannot know, so we need to tell it we're in
+     * 32-bit now, then switch to 16-bit (is there a better way to do it than
+     * adding 1 by hand ?) and tell the asm we're now in 16-bit mode so that
+     * it generates correct instructions. Note that we do not support thumb1.
+     */
+    ".code 32\n"
+    "add     r0, pc, #1\n"
+    "bx      r0\n"
+    ".code 16\n"
+#endif
+    "pop {%r0}\n"                 // argc was in the stack
+    "mov %r1, %sp\n"              // argv = sp
+    "add %r2, %r1, %r0, lsl #2\n" // envp = argv + 4*argc ...
+    "add %r2, %r2, $4\n"          //        ... + 4
+    "and %r3, %r1, $-8\n"         // AAPCS : sp must be 8-byte aligned in the
+    "mov %sp, %r3\n"              //         callee, an bl doesn't push (lr=pc)
+    "bl main\n"                   // main() returns the status code, we'll exit with it.
+    "movs r7, $1\n"               // NR_exit == 1
+    "svc $0x00\n"
+    "");
+
+#endif // _NOLIBC_ARCH_ARM_H
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch-i386.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch-i386.h
@@ -0,0 +1,196 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * i386 specific definitions for NOLIBC
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_ARCH_I386_H
+#define _NOLIBC_ARCH_I386_H
+
+/* O_* macros for fcntl/open are architecture-specific */
+#define O_RDONLY            0
+#define O_WRONLY            1
+#define O_RDWR              2
+#define O_CREAT          0x40
+#define O_EXCL           0x80
+#define O_NOCTTY        0x100
+#define O_TRUNC         0x200
+#define O_APPEND        0x400
+#define O_NONBLOCK      0x800
+#define O_DIRECTORY   0x10000
+
+/* The struct returned by the stat() syscall, 32-bit only, the syscall returns
+ * exactly 56 bytes (stops before the unused array).
+ */
+struct sys_stat_struct {
+	unsigned long  st_dev;
+	unsigned long  st_ino;
+	unsigned short st_mode;
+	unsigned short st_nlink;
+	unsigned short st_uid;
+	unsigned short st_gid;
+
+	unsigned long  st_rdev;
+	unsigned long  st_size;
+	unsigned long  st_blksize;
+	unsigned long  st_blocks;
+
+	unsigned long  st_atime;
+	unsigned long  st_atime_nsec;
+	unsigned long  st_mtime;
+	unsigned long  st_mtime_nsec;
+
+	unsigned long  st_ctime;
+	unsigned long  st_ctime_nsec;
+	unsigned long  __unused[2];
+};
+
+/* Syscalls for i386 :
+ *   - mostly similar to x86_64
+ *   - registers are 32-bit
+ *   - syscall number is passed in eax
+ *   - arguments are in ebx, ecx, edx, esi, edi, ebp respectively
+ *   - all registers are preserved (except eax of course)
+ *   - the system call is performed by calling int $0x80
+ *   - syscall return comes in eax
+ *   - the arguments are cast to long and assigned into the target registers
+ *     which are then simply passed as registers to the asm code, so that we
+ *     don't have to experience issues with register constraints.
+ *   - the syscall number is always specified last in order to allow to force
+ *     some registers before (gcc refuses a %-register at the last position).
+ *
+ * Also, i386 supports the old_select syscall if newselect is not available
+ */
+#define __ARCH_WANT_SYS_OLD_SELECT
+
+#define my_syscall0(num)                                                      \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num asm("eax") = (num);                                \
+	                                                                      \
+	asm volatile (                                                        \
+		"int $0x80\n"                                                 \
+		: "=a" (_ret)                                                 \
+		: "0"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall1(num, arg1)                                                \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num asm("eax") = (num);                                \
+	register long _arg1 asm("ebx") = (long)(arg1);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"int $0x80\n"                                                 \
+		: "=a" (_ret)                                                 \
+		: "r"(_arg1),                                                 \
+		  "0"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall2(num, arg1, arg2)                                          \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num asm("eax") = (num);                                \
+	register long _arg1 asm("ebx") = (long)(arg1);                        \
+	register long _arg2 asm("ecx") = (long)(arg2);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"int $0x80\n"                                                 \
+		: "=a" (_ret)                                                 \
+		: "r"(_arg1), "r"(_arg2),                                     \
+		  "0"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall3(num, arg1, arg2, arg3)                                    \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num asm("eax") = (num);                                \
+	register long _arg1 asm("ebx") = (long)(arg1);                        \
+	register long _arg2 asm("ecx") = (long)(arg2);                        \
+	register long _arg3 asm("edx") = (long)(arg3);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"int $0x80\n"                                                 \
+		: "=a" (_ret)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
+		  "0"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num asm("eax") = (num);                                \
+	register long _arg1 asm("ebx") = (long)(arg1);                        \
+	register long _arg2 asm("ecx") = (long)(arg2);                        \
+	register long _arg3 asm("edx") = (long)(arg3);                        \
+	register long _arg4 asm("esi") = (long)(arg4);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"int $0x80\n"                                                 \
+		: "=a" (_ret)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
+		  "0"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num asm("eax") = (num);                                \
+	register long _arg1 asm("ebx") = (long)(arg1);                        \
+	register long _arg2 asm("ecx") = (long)(arg2);                        \
+	register long _arg3 asm("edx") = (long)(arg3);                        \
+	register long _arg4 asm("esi") = (long)(arg4);                        \
+	register long _arg5 asm("edi") = (long)(arg5);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"int $0x80\n"                                                 \
+		: "=a" (_ret)                                                 \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
+		  "0"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+/* startup code */
+/*
+ * i386 System V ABI mandates:
+ * 1) last pushed argument must be 16-byte aligned.
+ * 2) The deepest stack frame should be set to zero
+ *
+ */
+asm(".section .text\n"
+    ".weak _start\n"
+    "_start:\n"
+    "pop %eax\n"                // argc   (first arg, %eax)
+    "mov %esp, %ebx\n"          // argv[] (second arg, %ebx)
+    "lea 4(%ebx,%eax,4),%ecx\n" // then a NULL then envp (third arg, %ecx)
+    "xor %ebp, %ebp\n"          // zero the stack frame
+    "and $-16, %esp\n"          // x86 ABI : esp must be 16-byte aligned before
+    "sub $4, %esp\n"            // the call instruction (args are aligned)
+    "push %ecx\n"               // push all registers on the stack so that we
+    "push %ebx\n"               // support both regparm and plain stack modes
+    "push %eax\n"
+    "call main\n"               // main() returns the status code in %eax
+    "mov %eax, %ebx\n"          // retrieve exit code (32-bit int)
+    "movl $1, %eax\n"           // NR_exit == 1
+    "int $0x80\n"               // exit now
+    "hlt\n"                     // ensure it does not
+    "");
+
+#endif // _NOLIBC_ARCH_I386_H
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch-mips.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch-mips.h
@@ -0,0 +1,217 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * MIPS specific definitions for NOLIBC
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_ARCH_MIPS_H
+#define _NOLIBC_ARCH_MIPS_H
+
+/* O_* macros for fcntl/open are architecture-specific */
+#define O_RDONLY            0
+#define O_WRONLY            1
+#define O_RDWR              2
+#define O_APPEND       0x0008
+#define O_NONBLOCK     0x0080
+#define O_CREAT        0x0100
+#define O_TRUNC        0x0200
+#define O_EXCL         0x0400
+#define O_NOCTTY       0x0800
+#define O_DIRECTORY   0x10000
+
+/* The struct returned by the stat() syscall. 88 bytes are returned by the
+ * syscall.
+ */
+struct sys_stat_struct {
+	unsigned int  st_dev;
+	long          st_pad1[3];
+	unsigned long st_ino;
+	unsigned int  st_mode;
+	unsigned int  st_nlink;
+	unsigned int  st_uid;
+	unsigned int  st_gid;
+	unsigned int  st_rdev;
+	long          st_pad2[2];
+	long          st_size;
+	long          st_pad3;
+
+	long          st_atime;
+	long          st_atime_nsec;
+	long          st_mtime;
+	long          st_mtime_nsec;
+
+	long          st_ctime;
+	long          st_ctime_nsec;
+	long          st_blksize;
+	long          st_blocks;
+	long          st_pad4[14];
+};
+
+/* Syscalls for MIPS ABI O32 :
+ *   - WARNING! there's always a delayed slot!
+ *   - WARNING again, the syntax is different, registers take a '$' and numbers
+ *     do not.
+ *   - registers are 32-bit
+ *   - stack is 8-byte aligned
+ *   - syscall number is passed in v0 (starts at 0xfa0).
+ *   - arguments are in a0, a1, a2, a3, then the stack. The caller needs to
+ *     leave some room in the stack for the callee to save a0..a3 if needed.
+ *   - Many registers are clobbered, in fact only a0..a2 and s0..s8 are
+ *     preserved. See: https://www.linux-mips.org/wiki/Syscall as well as
+ *     scall32-o32.S in the kernel sources.
+ *   - the system call is performed by calling "syscall"
+ *   - syscall return comes in v0, and register a3 needs to be checked to know
+ *     if an error occurred, in which case errno is in v0.
+ *   - the arguments are cast to long and assigned into the target registers
+ *     which are then simply passed as registers to the asm code, so that we
+ *     don't have to experience issues with register constraints.
+ */
+
+#define my_syscall0(num)                                                      \
+({                                                                            \
+	register long _num asm("v0") = (num);                                 \
+	register long _arg4 asm("a3");                                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"addiu $sp, $sp, -32\n"                                       \
+		"syscall\n"                                                   \
+		"addiu $sp, $sp, 32\n"                                        \
+		: "=r"(_num), "=r"(_arg4)                                     \
+		: "r"(_num)                                                   \
+		: "memory", "cc", "at", "v1", "hi", "lo",                     \
+	          "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
+	);                                                                    \
+	_arg4 ? -_num : _num;                                                 \
+})
+
+#define my_syscall1(num, arg1)                                                \
+({                                                                            \
+	register long _num asm("v0") = (num);                                 \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg4 asm("a3");                                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"addiu $sp, $sp, -32\n"                                       \
+		"syscall\n"                                                   \
+		"addiu $sp, $sp, 32\n"                                        \
+		: "=r"(_num), "=r"(_arg4)                                     \
+		: "0"(_num),                                                  \
+		  "r"(_arg1)                                                  \
+		: "memory", "cc", "at", "v1", "hi", "lo",                     \
+	          "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
+	);                                                                    \
+	_arg4 ? -_num : _num;                                                 \
+})
+
+#define my_syscall2(num, arg1, arg2)                                          \
+({                                                                            \
+	register long _num asm("v0") = (num);                                 \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg4 asm("a3");                                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"addiu $sp, $sp, -32\n"                                       \
+		"syscall\n"                                                   \
+		"addiu $sp, $sp, 32\n"                                        \
+		: "=r"(_num), "=r"(_arg4)                                     \
+		: "0"(_num),                                                  \
+		  "r"(_arg1), "r"(_arg2)                                      \
+		: "memory", "cc", "at", "v1", "hi", "lo",                     \
+	          "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
+	);                                                                    \
+	_arg4 ? -_num : _num;                                                 \
+})
+
+#define my_syscall3(num, arg1, arg2, arg3)                                    \
+({                                                                            \
+	register long _num asm("v0")  = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+	register long _arg4 asm("a3");                                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"addiu $sp, $sp, -32\n"                                       \
+		"syscall\n"                                                   \
+		"addiu $sp, $sp, 32\n"                                        \
+		: "=r"(_num), "=r"(_arg4)                                     \
+		: "0"(_num),                                                  \
+		  "r"(_arg1), "r"(_arg2), "r"(_arg3)                          \
+		: "memory", "cc", "at", "v1", "hi", "lo",                     \
+	          "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
+	);                                                                    \
+	_arg4 ? -_num : _num;                                                 \
+})
+
+#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
+({                                                                            \
+	register long _num asm("v0") = (num);                                 \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+	register long _arg4 asm("a3") = (long)(arg4);                         \
+	                                                                      \
+	asm volatile (                                                        \
+		"addiu $sp, $sp, -32\n"                                       \
+		"syscall\n"                                                   \
+		"addiu $sp, $sp, 32\n"                                        \
+		: "=r" (_num), "=r"(_arg4)                                    \
+		: "0"(_num),                                                  \
+		  "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4)              \
+		: "memory", "cc", "at", "v1", "hi", "lo",                     \
+	          "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
+	);                                                                    \
+	_arg4 ? -_num : _num;                                                 \
+})
+
+#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
+({                                                                            \
+	register long _num asm("v0") = (num);                                 \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+	register long _arg4 asm("a3") = (long)(arg4);                         \
+	register long _arg5 = (long)(arg5);                                   \
+	                                                                      \
+	asm volatile (                                                        \
+		"addiu $sp, $sp, -32\n"                                       \
+		"sw %7, 16($sp)\n"                                            \
+		"syscall\n  "                                                 \
+		"addiu $sp, $sp, 32\n"                                        \
+		: "=r" (_num), "=r"(_arg4)                                    \
+		: "0"(_num),                                                  \
+		  "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5)  \
+		: "memory", "cc", "at", "v1", "hi", "lo",                     \
+	          "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
+	);                                                                    \
+	_arg4 ? -_num : _num;                                                 \
+})
+
+/* startup code, note that it's called __start on MIPS */
+asm(".section .text\n"
+    ".weak __start\n"
+    ".set nomips16\n"
+    ".set push\n"
+    ".set    noreorder\n"
+    ".option pic0\n"
+    ".ent __start\n"
+    "__start:\n"
+    "lw $a0,($sp)\n"              // argc was in the stack
+    "addiu  $a1, $sp, 4\n"        // argv = sp + 4
+    "sll $a2, $a0, 2\n"           // a2 = argc * 4
+    "add   $a2, $a2, $a1\n"       // envp = argv + 4*argc ...
+    "addiu $a2, $a2, 4\n"         //        ... + 4
+    "li $t0, -8\n"
+    "and $sp, $sp, $t0\n"         // sp must be 8-byte aligned
+    "addiu $sp,$sp,-16\n"         // the callee expects to save a0..a3 there!
+    "jal main\n"                  // main() returns the status code, we'll exit with it.
+    "nop\n"                       // delayed slot
+    "move $a0, $v0\n"             // retrieve 32-bit exit code from v0
+    "li $v0, 4001\n"              // NR_exit == 4001
+    "syscall\n"
+    ".end __start\n"
+    ".set pop\n"
+    "");
+
+#endif // _NOLIBC_ARCH_MIPS_H
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch-riscv.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch-riscv.h
@@ -0,0 +1,204 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * RISCV (32 and 64) specific definitions for NOLIBC
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_ARCH_RISCV_H
+#define _NOLIBC_ARCH_RISCV_H
+
+/* O_* macros for fcntl/open are architecture-specific */
+#define O_RDONLY            0
+#define O_WRONLY            1
+#define O_RDWR              2
+#define O_CREAT          0x40
+#define O_EXCL           0x80
+#define O_NOCTTY        0x100
+#define O_TRUNC         0x200
+#define O_APPEND        0x400
+#define O_NONBLOCK      0x800
+#define O_DIRECTORY   0x10000
+
+struct sys_stat_struct {
+	unsigned long	st_dev;		/* Device.  */
+	unsigned long	st_ino;		/* File serial number.  */
+	unsigned int	st_mode;	/* File mode.  */
+	unsigned int	st_nlink;	/* Link count.  */
+	unsigned int	st_uid;		/* User ID of the file's owner.  */
+	unsigned int	st_gid;		/* Group ID of the file's group. */
+	unsigned long	st_rdev;	/* Device number, if device.  */
+	unsigned long	__pad1;
+	long		st_size;	/* Size of file, in bytes.  */
+	int		st_blksize;	/* Optimal block size for I/O.  */
+	int		__pad2;
+	long		st_blocks;	/* Number 512-byte blocks allocated. */
+	long		st_atime;	/* Time of last access.  */
+	unsigned long	st_atime_nsec;
+	long		st_mtime;	/* Time of last modification.  */
+	unsigned long	st_mtime_nsec;
+	long		st_ctime;	/* Time of last status change.  */
+	unsigned long	st_ctime_nsec;
+	unsigned int	__unused4;
+	unsigned int	__unused5;
+};
+
+#if   __riscv_xlen == 64
+#define PTRLOG "3"
+#define SZREG  "8"
+#elif __riscv_xlen == 32
+#define PTRLOG "2"
+#define SZREG  "4"
+#endif
+
+/* Syscalls for RISCV :
+ *   - stack is 16-byte aligned
+ *   - syscall number is passed in a7
+ *   - arguments are in a0, a1, a2, a3, a4, a5
+ *   - the system call is performed by calling ecall
+ *   - syscall return comes in a0
+ *   - the arguments are cast to long and assigned into the target
+ *     registers which are then simply passed as registers to the asm code,
+ *     so that we don't have to experience issues with register constraints.
+ *
+ * On riscv, select() is not implemented so we have to use pselect6().
+ */
+#define __ARCH_WANT_SYS_PSELECT6
+
+#define my_syscall0(num)                                                      \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0");                                        \
+									      \
+	asm volatile (                                                        \
+		"ecall\n\t"                                                   \
+		: "=r"(_arg1)                                                 \
+		: "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall1(num, arg1)                                                \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);		              \
+									      \
+	asm volatile (                                                        \
+		"ecall\n"                                                     \
+		: "+r"(_arg1)                                                 \
+		: "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall2(num, arg1, arg2)                                          \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+									      \
+	asm volatile (                                                        \
+		"ecall\n"                                                     \
+		: "+r"(_arg1)                                                 \
+		: "r"(_arg2),                                                 \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall3(num, arg1, arg2, arg3)                                    \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+									      \
+	asm volatile (                                                        \
+		"ecall\n\t"                                                   \
+		: "+r"(_arg1)                                                 \
+		: "r"(_arg2), "r"(_arg3),                                     \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+	register long _arg4 asm("a3") = (long)(arg4);                         \
+									      \
+	asm volatile (                                                        \
+		"ecall\n"                                                     \
+		: "+r"(_arg1)                                                 \
+		: "r"(_arg2), "r"(_arg3), "r"(_arg4),                         \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+	register long _arg4 asm("a3") = (long)(arg4);                         \
+	register long _arg5 asm("a4") = (long)(arg5);                         \
+									      \
+	asm volatile (                                                        \
+		"ecall\n"                                                     \
+		: "+r"(_arg1)                                                 \
+		: "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5),             \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+#define my_syscall6(num, arg1, arg2, arg3, arg4, arg5, arg6)                  \
+({                                                                            \
+	register long _num  asm("a7") = (num);                                \
+	register long _arg1 asm("a0") = (long)(arg1);                         \
+	register long _arg2 asm("a1") = (long)(arg2);                         \
+	register long _arg3 asm("a2") = (long)(arg3);                         \
+	register long _arg4 asm("a3") = (long)(arg4);                         \
+	register long _arg5 asm("a4") = (long)(arg5);                         \
+	register long _arg6 asm("a5") = (long)(arg6);                         \
+									      \
+	asm volatile (                                                        \
+		"ecall\n"                                                     \
+		: "+r"(_arg1)                                                 \
+		: "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), "r"(_arg6), \
+		  "r"(_num)                                                   \
+		: "memory", "cc"                                              \
+	);                                                                    \
+	_arg1;                                                                \
+})
+
+/* startup code */
+asm(".section .text\n"
+    ".weak _start\n"
+    "_start:\n"
+    ".option push\n"
+    ".option norelax\n"
+    "lla   gp, __global_pointer$\n"
+    ".option pop\n"
+    "ld    a0, 0(sp)\n"          // argc (a0) was in the stack
+    "add   a1, sp, "SZREG"\n"    // argv (a1) = sp
+    "slli  a2, a0, "PTRLOG"\n"   // envp (a2) = SZREG*argc ...
+    "add   a2, a2, "SZREG"\n"    //             + SZREG (skip null)
+    "add   a2,a2,a1\n"           //             + argv
+    "andi  sp,a1,-16\n"          // sp must be 16-byte aligned
+    "call  main\n"               // main() returns the status code, we'll exit with it.
+    "li a7, 93\n"                // NR_exit == 93
+    "ecall\n"
+    "");
+
+#endif // _NOLIBC_ARCH_RISCV_H
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch-x86_64.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch-x86_64.h
@@ -0,0 +1,215 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * x86_64 specific definitions for NOLIBC
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_ARCH_X86_64_H
+#define _NOLIBC_ARCH_X86_64_H
+
+/* O_* macros for fcntl/open are architecture-specific */
+#define O_RDONLY            0
+#define O_WRONLY            1
+#define O_RDWR              2
+#define O_CREAT          0x40
+#define O_EXCL           0x80
+#define O_NOCTTY        0x100
+#define O_TRUNC         0x200
+#define O_APPEND        0x400
+#define O_NONBLOCK      0x800
+#define O_DIRECTORY   0x10000
+
+/* The struct returned by the stat() syscall, equivalent to stat64(). The
+ * syscall returns 116 bytes and stops in the middle of __unused.
+ */
+struct sys_stat_struct {
+	unsigned long st_dev;
+	unsigned long st_ino;
+	unsigned long st_nlink;
+	unsigned int  st_mode;
+	unsigned int  st_uid;
+
+	unsigned int  st_gid;
+	unsigned int  __pad0;
+	unsigned long st_rdev;
+	long          st_size;
+	long          st_blksize;
+
+	long          st_blocks;
+	unsigned long st_atime;
+	unsigned long st_atime_nsec;
+	unsigned long st_mtime;
+
+	unsigned long st_mtime_nsec;
+	unsigned long st_ctime;
+	unsigned long st_ctime_nsec;
+	long          __unused[3];
+};
+
+/* Syscalls for x86_64 :
+ *   - registers are 64-bit
+ *   - syscall number is passed in rax
+ *   - arguments are in rdi, rsi, rdx, r10, r8, r9 respectively
+ *   - the system call is performed by calling the syscall instruction
+ *   - syscall return comes in rax
+ *   - rcx and r11 are clobbered, others are preserved.
+ *   - the arguments are cast to long and assigned into the target registers
+ *     which are then simply passed as registers to the asm code, so that we
+ *     don't have to experience issues with register constraints.
+ *   - the syscall number is always specified last in order to allow to force
+ *     some registers before (gcc refuses a %-register at the last position).
+ *   - see also x86-64 ABI section A.2 AMD64 Linux Kernel Conventions, A.2.1
+ *     Calling Conventions.
+ *
+ * Link x86-64 ABI: https://gitlab.com/x86-psABIs/x86-64-ABI/-/wikis/x86-64-psABI
+ *
+ */
+
+#define my_syscall0(num)                                                      \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "0"(_num)                                                   \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall1(num, arg1)                                                \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	register long _arg1 asm("rdi") = (long)(arg1);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "r"(_arg1),                                                 \
+		  "0"(_num)                                                   \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall2(num, arg1, arg2)                                          \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	register long _arg1 asm("rdi") = (long)(arg1);                        \
+	register long _arg2 asm("rsi") = (long)(arg2);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "r"(_arg1), "r"(_arg2),                                     \
+		  "0"(_num)                                                   \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall3(num, arg1, arg2, arg3)                                    \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	register long _arg1 asm("rdi") = (long)(arg1);                        \
+	register long _arg2 asm("rsi") = (long)(arg2);                        \
+	register long _arg3 asm("rdx") = (long)(arg3);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
+		  "0"(_num)                                                   \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	register long _arg1 asm("rdi") = (long)(arg1);                        \
+	register long _arg2 asm("rsi") = (long)(arg2);                        \
+	register long _arg3 asm("rdx") = (long)(arg3);                        \
+	register long _arg4 asm("r10") = (long)(arg4);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
+		  "0"(_num)                                                   \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	register long _arg1 asm("rdi") = (long)(arg1);                        \
+	register long _arg2 asm("rsi") = (long)(arg2);                        \
+	register long _arg3 asm("rdx") = (long)(arg3);                        \
+	register long _arg4 asm("r10") = (long)(arg4);                        \
+	register long _arg5 asm("r8")  = (long)(arg5);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
+		  "0"(_num)                                                   \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+#define my_syscall6(num, arg1, arg2, arg3, arg4, arg5, arg6)                  \
+({                                                                            \
+	long _ret;                                                            \
+	register long _num  asm("rax") = (num);                               \
+	register long _arg1 asm("rdi") = (long)(arg1);                        \
+	register long _arg2 asm("rsi") = (long)(arg2);                        \
+	register long _arg3 asm("rdx") = (long)(arg3);                        \
+	register long _arg4 asm("r10") = (long)(arg4);                        \
+	register long _arg5 asm("r8")  = (long)(arg5);                        \
+	register long _arg6 asm("r9")  = (long)(arg6);                        \
+	                                                                      \
+	asm volatile (                                                        \
+		"syscall\n"                                                   \
+		: "=a"(_ret)                                                  \
+		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
+		  "r"(_arg6), "0"(_num)                                       \
+		: "rcx", "r11", "memory", "cc"                                \
+	);                                                                    \
+	_ret;                                                                 \
+})
+
+/* startup code */
+/*
+ * x86-64 System V ABI mandates:
+ * 1) %rsp must be 16-byte aligned right before the function call.
+ * 2) The deepest stack frame should be zero (the %rbp).
+ *
+ */
+asm(".section .text\n"
+    ".weak _start\n"
+    "_start:\n"
+    "pop %rdi\n"                // argc   (first arg, %rdi)
+    "mov %rsp, %rsi\n"          // argv[] (second arg, %rsi)
+    "lea 8(%rsi,%rdi,8),%rdx\n" // then a NULL then envp (third arg, %rdx)
+    "xor %ebp, %ebp\n"          // zero the stack frame
+    "and $-16, %rsp\n"          // x86 ABI : esp must be 16-byte aligned before call
+    "call main\n"               // main() returns the status code, we'll exit with it.
+    "mov %eax, %edi\n"          // retrieve exit code (32 bit)
+    "mov $60, %eax\n"           // NR_exit == 60
+    "syscall\n"                 // really exit
+    "hlt\n"                     // ensure it does not return
+    "");
+
+#endif // _NOLIBC_ARCH_X86_64_H
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/arch.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/arch.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * Copyright (C) 2017-2022 Willy Tarreau <w@1wt.eu>
+ */
+
+/* Below comes the architecture-specific code. For each architecture, we have
+ * the syscall declarations and the _start code definition. This is the only
+ * global part. On all architectures the kernel puts everything in the stack
+ * before jumping to _start just above us, without any return address (_start
+ * is not a function but an entry pint). So at the stack pointer we find argc.
+ * Then argv[] begins, and ends at the first NULL. Then we have envp which
+ * starts and ends with a NULL as well. So envp=argv+argc+1.
+ */
+
+#ifndef _NOLIBC_ARCH_H
+#define _NOLIBC_ARCH_H
+
+#if defined(__x86_64__)
+#include "arch-x86_64.h"
+#elif defined(__i386__) || defined(__i486__) || defined(__i586__) || defined(__i686__)
+#include "arch-i386.h"
+#elif defined(__ARM_EABI__)
+#include "arch-arm.h"
+#elif defined(__aarch64__)
+#include "arch-aarch64.h"
+#elif defined(__mips__) && defined(_ABIO32)
+#include "arch-mips.h"
+#elif defined(__riscv)
+#include "arch-riscv.h"
+#endif
+
+#endif /* _NOLIBC_ARCH_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/nolibc.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/nolibc.h
@@ -81,13 +81,21 @@
  *
  */
 
+/* standard type definitions */
+#include "std.h"
+
+/* system includes */
 #include <asm/unistd.h>
+#include <asm/signal.h>  // for SIGCHLD
 #include <asm/ioctls.h>
 #include <asm/errno.h>
 #include <linux/fs.h>
 #include <linux/loop.h>
 #include <linux/time.h>
+#include "arch.h"
+#include "types.h"
 
+/* Used by programs to avoid std includes */
 #define NOLIBC
 
 /* this way it will be removed if unused */
@@ -104,1318 +112,6 @@
  */
 #define MAX_ERRNO 4095
 
-/* Declare a few quite common macros and types that usually are in stdlib.h,
- * stdint.h, ctype.h, unistd.h and a few other common locations.
- */
-
-#define NULL ((void *)0)
-
-/* stdint types */
-typedef unsigned char       uint8_t;
-typedef   signed char        int8_t;
-typedef unsigned short     uint16_t;
-typedef   signed short      int16_t;
-typedef unsigned int       uint32_t;
-typedef   signed int        int32_t;
-typedef unsigned long long uint64_t;
-typedef   signed long long  int64_t;
-typedef unsigned long        size_t;
-typedef   signed long       ssize_t;
-typedef unsigned long     uintptr_t;
-typedef   signed long      intptr_t;
-typedef   signed long     ptrdiff_t;
-
-/* for stat() */
-typedef unsigned int          dev_t;
-typedef unsigned long         ino_t;
-typedef unsigned int         mode_t;
-typedef   signed int          pid_t;
-typedef unsigned int          uid_t;
-typedef unsigned int          gid_t;
-typedef unsigned long       nlink_t;
-typedef   signed long         off_t;
-typedef   signed long     blksize_t;
-typedef   signed long      blkcnt_t;
-typedef   signed long        time_t;
-
-/* for poll() */
-struct pollfd {
-	int fd;
-	short int events;
-	short int revents;
-};
-
-/* for getdents64() */
-struct linux_dirent64 {
-	uint64_t       d_ino;
-	int64_t        d_off;
-	unsigned short d_reclen;
-	unsigned char  d_type;
-	char           d_name[];
-};
-
-/* commonly an fd_set represents 256 FDs */
-#define FD_SETSIZE 256
-typedef struct { uint32_t fd32[FD_SETSIZE/32]; } fd_set;
-
-/* needed by wait4() */
-struct rusage {
-	struct timeval ru_utime;
-	struct timeval ru_stime;
-	long   ru_maxrss;
-	long   ru_ixrss;
-	long   ru_idrss;
-	long   ru_isrss;
-	long   ru_minflt;
-	long   ru_majflt;
-	long   ru_nswap;
-	long   ru_inblock;
-	long   ru_oublock;
-	long   ru_msgsnd;
-	long   ru_msgrcv;
-	long   ru_nsignals;
-	long   ru_nvcsw;
-	long   ru_nivcsw;
-};
-
-/* stat flags (WARNING, octal here) */
-#define S_IFDIR       0040000
-#define S_IFCHR       0020000
-#define S_IFBLK       0060000
-#define S_IFREG       0100000
-#define S_IFIFO       0010000
-#define S_IFLNK       0120000
-#define S_IFSOCK      0140000
-#define S_IFMT        0170000
-
-#define S_ISDIR(mode)  (((mode) & S_IFDIR) == S_IFDIR)
-#define S_ISCHR(mode)  (((mode) & S_IFCHR) == S_IFCHR)
-#define S_ISBLK(mode)  (((mode) & S_IFBLK) == S_IFBLK)
-#define S_ISREG(mode)  (((mode) & S_IFREG) == S_IFREG)
-#define S_ISFIFO(mode) (((mode) & S_IFIFO) == S_IFIFO)
-#define S_ISLNK(mode)  (((mode) & S_IFLNK) == S_IFLNK)
-#define S_ISSOCK(mode) (((mode) & S_IFSOCK) == S_IFSOCK)
-
-#define DT_UNKNOWN 0
-#define DT_FIFO    1
-#define DT_CHR     2
-#define DT_DIR     4
-#define DT_BLK     6
-#define DT_REG     8
-#define DT_LNK    10
-#define DT_SOCK   12
-
-/* all the *at functions */
-#ifndef AT_FDCWD
-#define AT_FDCWD             -100
-#endif
-
-/* lseek */
-#define SEEK_SET        0
-#define SEEK_CUR        1
-#define SEEK_END        2
-
-/* reboot */
-#define LINUX_REBOOT_MAGIC1         0xfee1dead
-#define LINUX_REBOOT_MAGIC2         0x28121969
-#define LINUX_REBOOT_CMD_HALT       0xcdef0123
-#define LINUX_REBOOT_CMD_POWER_OFF  0x4321fedc
-#define LINUX_REBOOT_CMD_RESTART    0x01234567
-#define LINUX_REBOOT_CMD_SW_SUSPEND 0xd000fce2
-
-
-/* The format of the struct as returned by the libc to the application, which
- * significantly differs from the format returned by the stat() syscall flavours.
- */
-struct stat {
-	dev_t     st_dev;     /* ID of device containing file */
-	ino_t     st_ino;     /* inode number */
-	mode_t    st_mode;    /* protection */
-	nlink_t   st_nlink;   /* number of hard links */
-	uid_t     st_uid;     /* user ID of owner */
-	gid_t     st_gid;     /* group ID of owner */
-	dev_t     st_rdev;    /* device ID (if special file) */
-	off_t     st_size;    /* total size, in bytes */
-	blksize_t st_blksize; /* blocksize for file system I/O */
-	blkcnt_t  st_blocks;  /* number of 512B blocks allocated */
-	time_t    st_atime;   /* time of last access */
-	time_t    st_mtime;   /* time of last modification */
-	time_t    st_ctime;   /* time of last status change */
-};
-
-#define WEXITSTATUS(status)   (((status) & 0xff00) >> 8)
-#define WIFEXITED(status)     (((status) & 0x7f) == 0)
-
-/* for SIGCHLD */
-#include <asm/signal.h>
-
-/* Below comes the architecture-specific code. For each architecture, we have
- * the syscall declarations and the _start code definition. This is the only
- * global part. On all architectures the kernel puts everything in the stack
- * before jumping to _start just above us, without any return address (_start
- * is not a function but an entry pint). So at the stack pointer we find argc.
- * Then argv[] begins, and ends at the first NULL. Then we have envp which
- * starts and ends with a NULL as well. So envp=argv+argc+1.
- */
-
-#if defined(__x86_64__)
-/* Syscalls for x86_64 :
- *   - registers are 64-bit
- *   - syscall number is passed in rax
- *   - arguments are in rdi, rsi, rdx, r10, r8, r9 respectively
- *   - the system call is performed by calling the syscall instruction
- *   - syscall return comes in rax
- *   - rcx and r8..r11 may be clobbered, others are preserved.
- *   - the arguments are cast to long and assigned into the target registers
- *     which are then simply passed as registers to the asm code, so that we
- *     don't have to experience issues with register constraints.
- *   - the syscall number is always specified last in order to allow to force
- *     some registers before (gcc refuses a %-register at the last position).
- */
-
-#define my_syscall0(num)                                                      \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret)                                                 \
-		: "0"(_num)                                                   \
-		: "rcx", "r8", "r9", "r10", "r11", "memory", "cc"             \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall1(num, arg1)                                                \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-	register long _arg1 asm("rdi") = (long)(arg1);                        \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1),                                                 \
-		  "0"(_num)                                                   \
-		: "rcx", "r8", "r9", "r10", "r11", "memory", "cc"             \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall2(num, arg1, arg2)                                          \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-	register long _arg1 asm("rdi") = (long)(arg1);                        \
-	register long _arg2 asm("rsi") = (long)(arg2);                        \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1), "r"(_arg2),                                     \
-		  "0"(_num)                                                   \
-		: "rcx", "r8", "r9", "r10", "r11", "memory", "cc"             \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall3(num, arg1, arg2, arg3)                                    \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-	register long _arg1 asm("rdi") = (long)(arg1);                        \
-	register long _arg2 asm("rsi") = (long)(arg2);                        \
-	register long _arg3 asm("rdx") = (long)(arg3);                        \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
-		  "0"(_num)                                                   \
-		: "rcx", "r8", "r9", "r10", "r11", "memory", "cc"             \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-	register long _arg1 asm("rdi") = (long)(arg1);                        \
-	register long _arg2 asm("rsi") = (long)(arg2);                        \
-	register long _arg3 asm("rdx") = (long)(arg3);                        \
-	register long _arg4 asm("r10") = (long)(arg4);                        \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret), "=r"(_arg4)                                    \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
-		  "0"(_num)                                                   \
-		: "rcx", "r8", "r9", "r11", "memory", "cc"                    \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-	register long _arg1 asm("rdi") = (long)(arg1);                        \
-	register long _arg2 asm("rsi") = (long)(arg2);                        \
-	register long _arg3 asm("rdx") = (long)(arg3);                        \
-	register long _arg4 asm("r10") = (long)(arg4);                        \
-	register long _arg5 asm("r8")  = (long)(arg5);                        \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret), "=r"(_arg4), "=r"(_arg5)                       \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
-		  "0"(_num)                                                   \
-		: "rcx", "r9", "r11", "memory", "cc"                          \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall6(num, arg1, arg2, arg3, arg4, arg5, arg6)                  \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num  asm("rax") = (num);                               \
-	register long _arg1 asm("rdi") = (long)(arg1);                        \
-	register long _arg2 asm("rsi") = (long)(arg2);                        \
-	register long _arg3 asm("rdx") = (long)(arg3);                        \
-	register long _arg4 asm("r10") = (long)(arg4);                        \
-	register long _arg5 asm("r8")  = (long)(arg5);                        \
-	register long _arg6 asm("r9")  = (long)(arg6);                        \
-									      \
-	asm volatile (                                                        \
-		"syscall\n"                                                   \
-		: "=a" (_ret), "=r"(_arg4), "=r"(_arg5)                       \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
-		  "r"(_arg6), "0"(_num)                                       \
-		: "rcx", "r11", "memory", "cc"                                \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-/* startup code */
-asm(".section .text\n"
-    ".global _start\n"
-    "_start:\n"
-    "pop %rdi\n"                // argc   (first arg, %rdi)
-    "mov %rsp, %rsi\n"          // argv[] (second arg, %rsi)
-    "lea 8(%rsi,%rdi,8),%rdx\n" // then a NULL then envp (third arg, %rdx)
-    "and $-16, %rsp\n"          // x86 ABI : esp must be 16-byte aligned when
-    "sub $8, %rsp\n"            // entering the callee
-    "call main\n"               // main() returns the status code, we'll exit with it.
-    "movzb %al, %rdi\n"         // retrieve exit code from 8 lower bits
-    "mov $60, %rax\n"           // NR_exit == 60
-    "syscall\n"                 // really exit
-    "hlt\n"                     // ensure it does not return
-    "");
-
-/* fcntl / open */
-#define O_RDONLY            0
-#define O_WRONLY            1
-#define O_RDWR              2
-#define O_CREAT          0x40
-#define O_EXCL           0x80
-#define O_NOCTTY        0x100
-#define O_TRUNC         0x200
-#define O_APPEND        0x400
-#define O_NONBLOCK      0x800
-#define O_DIRECTORY   0x10000
-
-/* The struct returned by the stat() syscall, equivalent to stat64(). The
- * syscall returns 116 bytes and stops in the middle of __unused.
- */
-struct sys_stat_struct {
-	unsigned long st_dev;
-	unsigned long st_ino;
-	unsigned long st_nlink;
-	unsigned int  st_mode;
-	unsigned int  st_uid;
-
-	unsigned int  st_gid;
-	unsigned int  __pad0;
-	unsigned long st_rdev;
-	long          st_size;
-	long          st_blksize;
-
-	long          st_blocks;
-	unsigned long st_atime;
-	unsigned long st_atime_nsec;
-	unsigned long st_mtime;
-
-	unsigned long st_mtime_nsec;
-	unsigned long st_ctime;
-	unsigned long st_ctime_nsec;
-	long          __unused[3];
-};
-
-#elif defined(__i386__) || defined(__i486__) || defined(__i586__) || defined(__i686__)
-/* Syscalls for i386 :
- *   - mostly similar to x86_64
- *   - registers are 32-bit
- *   - syscall number is passed in eax
- *   - arguments are in ebx, ecx, edx, esi, edi, ebp respectively
- *   - all registers are preserved (except eax of course)
- *   - the system call is performed by calling int $0x80
- *   - syscall return comes in eax
- *   - the arguments are cast to long and assigned into the target registers
- *     which are then simply passed as registers to the asm code, so that we
- *     don't have to experience issues with register constraints.
- *   - the syscall number is always specified last in order to allow to force
- *     some registers before (gcc refuses a %-register at the last position).
- *
- * Also, i386 supports the old_select syscall if newselect is not available
- */
-#define __ARCH_WANT_SYS_OLD_SELECT
-
-#define my_syscall0(num)                                                      \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num asm("eax") = (num);                                \
-									      \
-	asm volatile (                                                        \
-		"int $0x80\n"                                                 \
-		: "=a" (_ret)                                                 \
-		: "0"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall1(num, arg1)                                                \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num asm("eax") = (num);                                \
-	register long _arg1 asm("ebx") = (long)(arg1);                        \
-									      \
-	asm volatile (                                                        \
-		"int $0x80\n"                                                 \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1),                                                 \
-		  "0"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall2(num, arg1, arg2)                                          \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num asm("eax") = (num);                                \
-	register long _arg1 asm("ebx") = (long)(arg1);                        \
-	register long _arg2 asm("ecx") = (long)(arg2);                        \
-									      \
-	asm volatile (                                                        \
-		"int $0x80\n"                                                 \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1), "r"(_arg2),                                     \
-		  "0"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall3(num, arg1, arg2, arg3)                                    \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num asm("eax") = (num);                                \
-	register long _arg1 asm("ebx") = (long)(arg1);                        \
-	register long _arg2 asm("ecx") = (long)(arg2);                        \
-	register long _arg3 asm("edx") = (long)(arg3);                        \
-									      \
-	asm volatile (                                                        \
-		"int $0x80\n"                                                 \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
-		  "0"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num asm("eax") = (num);                                \
-	register long _arg1 asm("ebx") = (long)(arg1);                        \
-	register long _arg2 asm("ecx") = (long)(arg2);                        \
-	register long _arg3 asm("edx") = (long)(arg3);                        \
-	register long _arg4 asm("esi") = (long)(arg4);                        \
-									      \
-	asm volatile (                                                        \
-		"int $0x80\n"                                                 \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
-		  "0"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
-({                                                                            \
-	long _ret;                                                            \
-	register long _num asm("eax") = (num);                                \
-	register long _arg1 asm("ebx") = (long)(arg1);                        \
-	register long _arg2 asm("ecx") = (long)(arg2);                        \
-	register long _arg3 asm("edx") = (long)(arg3);                        \
-	register long _arg4 asm("esi") = (long)(arg4);                        \
-	register long _arg5 asm("edi") = (long)(arg5);                        \
-									      \
-	asm volatile (                                                        \
-		"int $0x80\n"                                                 \
-		: "=a" (_ret)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
-		  "0"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_ret;                                                                 \
-})
-
-/* startup code */
-asm(".section .text\n"
-    ".global _start\n"
-    "_start:\n"
-    "pop %eax\n"                // argc   (first arg, %eax)
-    "mov %esp, %ebx\n"          // argv[] (second arg, %ebx)
-    "lea 4(%ebx,%eax,4),%ecx\n" // then a NULL then envp (third arg, %ecx)
-    "and $-16, %esp\n"          // x86 ABI : esp must be 16-byte aligned when
-    "push %ecx\n"               // push all registers on the stack so that we
-    "push %ebx\n"               // support both regparm and plain stack modes
-    "push %eax\n"
-    "call main\n"               // main() returns the status code in %eax
-    "movzbl %al, %ebx\n"        // retrieve exit code from lower 8 bits
-    "movl   $1, %eax\n"         // NR_exit == 1
-    "int    $0x80\n"            // exit now
-    "hlt\n"                     // ensure it does not
-    "");
-
-/* fcntl / open */
-#define O_RDONLY            0
-#define O_WRONLY            1
-#define O_RDWR              2
-#define O_CREAT          0x40
-#define O_EXCL           0x80
-#define O_NOCTTY        0x100
-#define O_TRUNC         0x200
-#define O_APPEND        0x400
-#define O_NONBLOCK      0x800
-#define O_DIRECTORY   0x10000
-
-/* The struct returned by the stat() syscall, 32-bit only, the syscall returns
- * exactly 56 bytes (stops before the unused array).
- */
-struct sys_stat_struct {
-	unsigned long  st_dev;
-	unsigned long  st_ino;
-	unsigned short st_mode;
-	unsigned short st_nlink;
-	unsigned short st_uid;
-	unsigned short st_gid;
-
-	unsigned long  st_rdev;
-	unsigned long  st_size;
-	unsigned long  st_blksize;
-	unsigned long  st_blocks;
-
-	unsigned long  st_atime;
-	unsigned long  st_atime_nsec;
-	unsigned long  st_mtime;
-	unsigned long  st_mtime_nsec;
-
-	unsigned long  st_ctime;
-	unsigned long  st_ctime_nsec;
-	unsigned long  __unused[2];
-};
-
-#elif defined(__ARM_EABI__)
-/* Syscalls for ARM in ARM or Thumb modes :
- *   - registers are 32-bit
- *   - stack is 8-byte aligned
- *     ( http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.faqs/ka4127.html)
- *   - syscall number is passed in r7
- *   - arguments are in r0, r1, r2, r3, r4, r5
- *   - the system call is performed by calling svc #0
- *   - syscall return comes in r0.
- *   - only lr is clobbered.
- *   - the arguments are cast to long and assigned into the target registers
- *     which are then simply passed as registers to the asm code, so that we
- *     don't have to experience issues with register constraints.
- *   - the syscall number is always specified last in order to allow to force
- *     some registers before (gcc refuses a %-register at the last position).
- *
- * Also, ARM supports the old_select syscall if newselect is not available
- */
-#define __ARCH_WANT_SYS_OLD_SELECT
-
-#define my_syscall0(num)                                                      \
-({                                                                            \
-	register long _num asm("r7") = (num);                                 \
-	register long _arg1 asm("r0");                                        \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_num)                                                   \
-		: "memory", "cc", "lr"                                        \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall1(num, arg1)                                                \
-({                                                                            \
-	register long _num asm("r7") = (num);                                 \
-	register long _arg1 asm("r0") = (long)(arg1);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1),                                                 \
-		  "r"(_num)                                                   \
-		: "memory", "cc", "lr"                                        \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall2(num, arg1, arg2)                                          \
-({                                                                            \
-	register long _num asm("r7") = (num);                                 \
-	register long _arg1 asm("r0") = (long)(arg1);                         \
-	register long _arg2 asm("r1") = (long)(arg2);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1), "r"(_arg2),                                     \
-		  "r"(_num)                                                   \
-		: "memory", "cc", "lr"                                        \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall3(num, arg1, arg2, arg3)                                    \
-({                                                                            \
-	register long _num asm("r7") = (num);                                 \
-	register long _arg1 asm("r0") = (long)(arg1);                         \
-	register long _arg2 asm("r1") = (long)(arg2);                         \
-	register long _arg3 asm("r2") = (long)(arg3);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
-		  "r"(_num)                                                   \
-		: "memory", "cc", "lr"                                        \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
-({                                                                            \
-	register long _num asm("r7") = (num);                                 \
-	register long _arg1 asm("r0") = (long)(arg1);                         \
-	register long _arg2 asm("r1") = (long)(arg2);                         \
-	register long _arg3 asm("r2") = (long)(arg3);                         \
-	register long _arg4 asm("r3") = (long)(arg4);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
-		  "r"(_num)                                                   \
-		: "memory", "cc", "lr"                                        \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
-({                                                                            \
-	register long _num asm("r7") = (num);                                 \
-	register long _arg1 asm("r0") = (long)(arg1);                         \
-	register long _arg2 asm("r1") = (long)(arg2);                         \
-	register long _arg3 asm("r2") = (long)(arg3);                         \
-	register long _arg4 asm("r3") = (long)(arg4);                         \
-	register long _arg5 asm("r4") = (long)(arg5);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r" (_arg1)                                                \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
-		  "r"(_num)                                                   \
-		: "memory", "cc", "lr"                                        \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-/* startup code */
-asm(".section .text\n"
-    ".global _start\n"
-    "_start:\n"
-#if defined(__THUMBEB__) || defined(__THUMBEL__)
-    /* We enter here in 32-bit mode but if some previous functions were in
-     * 16-bit mode, the assembler cannot know, so we need to tell it we're in
-     * 32-bit now, then switch to 16-bit (is there a better way to do it than
-     * adding 1 by hand ?) and tell the asm we're now in 16-bit mode so that
-     * it generates correct instructions. Note that we do not support thumb1.
-     */
-    ".code 32\n"
-    "add     r0, pc, #1\n"
-    "bx      r0\n"
-    ".code 16\n"
-#endif
-    "pop {%r0}\n"                 // argc was in the stack
-    "mov %r1, %sp\n"              // argv = sp
-    "add %r2, %r1, %r0, lsl #2\n" // envp = argv + 4*argc ...
-    "add %r2, %r2, $4\n"          //        ... + 4
-    "and %r3, %r1, $-8\n"         // AAPCS : sp must be 8-byte aligned in the
-    "mov %sp, %r3\n"              //         callee, an bl doesn't push (lr=pc)
-    "bl main\n"                   // main() returns the status code, we'll exit with it.
-    "and %r0, %r0, $0xff\n"       // limit exit code to 8 bits
-    "movs r7, $1\n"               // NR_exit == 1
-    "svc $0x00\n"
-    "");
-
-/* fcntl / open */
-#define O_RDONLY            0
-#define O_WRONLY            1
-#define O_RDWR              2
-#define O_CREAT          0x40
-#define O_EXCL           0x80
-#define O_NOCTTY        0x100
-#define O_TRUNC         0x200
-#define O_APPEND        0x400
-#define O_NONBLOCK      0x800
-#define O_DIRECTORY    0x4000
-
-/* The struct returned by the stat() syscall, 32-bit only, the syscall returns
- * exactly 56 bytes (stops before the unused array). In big endian, the format
- * differs as devices are returned as short only.
- */
-struct sys_stat_struct {
-#if defined(__ARMEB__)
-	unsigned short st_dev;
-	unsigned short __pad1;
-#else
-	unsigned long  st_dev;
-#endif
-	unsigned long  st_ino;
-	unsigned short st_mode;
-	unsigned short st_nlink;
-	unsigned short st_uid;
-	unsigned short st_gid;
-#if defined(__ARMEB__)
-	unsigned short st_rdev;
-	unsigned short __pad2;
-#else
-	unsigned long  st_rdev;
-#endif
-	unsigned long  st_size;
-	unsigned long  st_blksize;
-	unsigned long  st_blocks;
-	unsigned long  st_atime;
-	unsigned long  st_atime_nsec;
-	unsigned long  st_mtime;
-	unsigned long  st_mtime_nsec;
-	unsigned long  st_ctime;
-	unsigned long  st_ctime_nsec;
-	unsigned long  __unused[2];
-};
-
-#elif defined(__aarch64__)
-/* Syscalls for AARCH64 :
- *   - registers are 64-bit
- *   - stack is 16-byte aligned
- *   - syscall number is passed in x8
- *   - arguments are in x0, x1, x2, x3, x4, x5
- *   - the system call is performed by calling svc 0
- *   - syscall return comes in x0.
- *   - the arguments are cast to long and assigned into the target registers
- *     which are then simply passed as registers to the asm code, so that we
- *     don't have to experience issues with register constraints.
- *
- * On aarch64, select() is not implemented so we have to use pselect6().
- */
-#define __ARCH_WANT_SYS_PSELECT6
-
-#define my_syscall0(num)                                                      \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0");                                        \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall1(num, arg1)                                                \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0") = (long)(arg1);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1),                                                 \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall2(num, arg1, arg2)                                          \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0") = (long)(arg1);                         \
-	register long _arg2 asm("x1") = (long)(arg2);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1), "r"(_arg2),                                     \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall3(num, arg1, arg2, arg3)                                    \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0") = (long)(arg1);                         \
-	register long _arg2 asm("x1") = (long)(arg2);                         \
-	register long _arg3 asm("x2") = (long)(arg3);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3),                         \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0") = (long)(arg1);                         \
-	register long _arg2 asm("x1") = (long)(arg2);                         \
-	register long _arg3 asm("x2") = (long)(arg3);                         \
-	register long _arg4 asm("x3") = (long)(arg4);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r"(_arg1)                                                 \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4),             \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0") = (long)(arg1);                         \
-	register long _arg2 asm("x1") = (long)(arg2);                         \
-	register long _arg3 asm("x2") = (long)(arg3);                         \
-	register long _arg4 asm("x3") = (long)(arg4);                         \
-	register long _arg5 asm("x4") = (long)(arg5);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r" (_arg1)                                                \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall6(num, arg1, arg2, arg3, arg4, arg5, arg6)                  \
-({                                                                            \
-	register long _num  asm("x8") = (num);                                \
-	register long _arg1 asm("x0") = (long)(arg1);                         \
-	register long _arg2 asm("x1") = (long)(arg2);                         \
-	register long _arg3 asm("x2") = (long)(arg3);                         \
-	register long _arg4 asm("x3") = (long)(arg4);                         \
-	register long _arg5 asm("x4") = (long)(arg5);                         \
-	register long _arg6 asm("x5") = (long)(arg6);                         \
-									      \
-	asm volatile (                                                        \
-		"svc #0\n"                                                    \
-		: "=r" (_arg1)                                                \
-		: "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), \
-		  "r"(_arg6), "r"(_num)                                       \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-/* startup code */
-asm(".section .text\n"
-    ".global _start\n"
-    "_start:\n"
-    "ldr x0, [sp]\n"              // argc (x0) was in the stack
-    "add x1, sp, 8\n"             // argv (x1) = sp
-    "lsl x2, x0, 3\n"             // envp (x2) = 8*argc ...
-    "add x2, x2, 8\n"             //           + 8 (skip null)
-    "add x2, x2, x1\n"            //           + argv
-    "and sp, x1, -16\n"           // sp must be 16-byte aligned in the callee
-    "bl main\n"                   // main() returns the status code, we'll exit with it.
-    "and x0, x0, 0xff\n"          // limit exit code to 8 bits
-    "mov x8, 93\n"                // NR_exit == 93
-    "svc #0\n"
-    "");
-
-/* fcntl / open */
-#define O_RDONLY            0
-#define O_WRONLY            1
-#define O_RDWR              2
-#define O_CREAT          0x40
-#define O_EXCL           0x80
-#define O_NOCTTY        0x100
-#define O_TRUNC         0x200
-#define O_APPEND        0x400
-#define O_NONBLOCK      0x800
-#define O_DIRECTORY    0x4000
-
-/* The struct returned by the newfstatat() syscall. Differs slightly from the
- * x86_64's stat one by field ordering, so be careful.
- */
-struct sys_stat_struct {
-	unsigned long   st_dev;
-	unsigned long   st_ino;
-	unsigned int    st_mode;
-	unsigned int    st_nlink;
-	unsigned int    st_uid;
-	unsigned int    st_gid;
-
-	unsigned long   st_rdev;
-	unsigned long   __pad1;
-	long            st_size;
-	int             st_blksize;
-	int             __pad2;
-
-	long            st_blocks;
-	long            st_atime;
-	unsigned long   st_atime_nsec;
-	long            st_mtime;
-
-	unsigned long   st_mtime_nsec;
-	long            st_ctime;
-	unsigned long   st_ctime_nsec;
-	unsigned int    __unused[2];
-};
-
-#elif defined(__mips__) && defined(_ABIO32)
-/* Syscalls for MIPS ABI O32 :
- *   - WARNING! there's always a delayed slot!
- *   - WARNING again, the syntax is different, registers take a '$' and numbers
- *     do not.
- *   - registers are 32-bit
- *   - stack is 8-byte aligned
- *   - syscall number is passed in v0 (starts at 0xfa0).
- *   - arguments are in a0, a1, a2, a3, then the stack. The caller needs to
- *     leave some room in the stack for the callee to save a0..a3 if needed.
- *   - Many registers are clobbered, in fact only a0..a2 and s0..s8 are
- *     preserved. See: https://www.linux-mips.org/wiki/Syscall as well as
- *     scall32-o32.S in the kernel sources.
- *   - the system call is performed by calling "syscall"
- *   - syscall return comes in v0, and register a3 needs to be checked to know
- *     if an error occurred, in which case errno is in v0.
- *   - the arguments are cast to long and assigned into the target registers
- *     which are then simply passed as registers to the asm code, so that we
- *     don't have to experience issues with register constraints.
- */
-
-#define my_syscall0(num)                                                      \
-({                                                                            \
-	register long _num asm("v0") = (num);                                 \
-	register long _arg4 asm("a3");                                        \
-									      \
-	asm volatile (                                                        \
-		"addiu $sp, $sp, -32\n"                                       \
-		"syscall\n"                                                   \
-		"addiu $sp, $sp, 32\n"                                        \
-		: "=r"(_num), "=r"(_arg4)                                     \
-		: "r"(_num)                                                   \
-		: "memory", "cc", "at", "v1", "hi", "lo",                     \
-		  "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
-	);                                                                    \
-	_arg4 ? -_num : _num;                                                 \
-})
-
-#define my_syscall1(num, arg1)                                                \
-({                                                                            \
-	register long _num asm("v0") = (num);                                 \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg4 asm("a3");                                        \
-									      \
-	asm volatile (                                                        \
-		"addiu $sp, $sp, -32\n"                                       \
-		"syscall\n"                                                   \
-		"addiu $sp, $sp, 32\n"                                        \
-		: "=r"(_num), "=r"(_arg4)                                     \
-		: "0"(_num),                                                  \
-		  "r"(_arg1)                                                  \
-		: "memory", "cc", "at", "v1", "hi", "lo",                     \
-		  "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
-	);                                                                    \
-	_arg4 ? -_num : _num;                                                 \
-})
-
-#define my_syscall2(num, arg1, arg2)                                          \
-({                                                                            \
-	register long _num asm("v0") = (num);                                 \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg4 asm("a3");                                        \
-									      \
-	asm volatile (                                                        \
-		"addiu $sp, $sp, -32\n"                                       \
-		"syscall\n"                                                   \
-		"addiu $sp, $sp, 32\n"                                        \
-		: "=r"(_num), "=r"(_arg4)                                     \
-		: "0"(_num),                                                  \
-		  "r"(_arg1), "r"(_arg2)                                      \
-		: "memory", "cc", "at", "v1", "hi", "lo",                     \
-		  "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
-	);                                                                    \
-	_arg4 ? -_num : _num;                                                 \
-})
-
-#define my_syscall3(num, arg1, arg2, arg3)                                    \
-({                                                                            \
-	register long _num asm("v0")  = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-	register long _arg4 asm("a3");                                        \
-									      \
-	asm volatile (                                                        \
-		"addiu $sp, $sp, -32\n"                                       \
-		"syscall\n"                                                   \
-		"addiu $sp, $sp, 32\n"                                        \
-		: "=r"(_num), "=r"(_arg4)                                     \
-		: "0"(_num),                                                  \
-		  "r"(_arg1), "r"(_arg2), "r"(_arg3)                          \
-		: "memory", "cc", "at", "v1", "hi", "lo",                     \
-		  "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
-	);                                                                    \
-	_arg4 ? -_num : _num;                                                 \
-})
-
-#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
-({                                                                            \
-	register long _num asm("v0") = (num);                                 \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-	register long _arg4 asm("a3") = (long)(arg4);                         \
-									      \
-	asm volatile (                                                        \
-		"addiu $sp, $sp, -32\n"                                       \
-		"syscall\n"                                                   \
-		"addiu $sp, $sp, 32\n"                                        \
-		: "=r" (_num), "=r"(_arg4)                                    \
-		: "0"(_num),                                                  \
-		  "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4)              \
-		: "memory", "cc", "at", "v1", "hi", "lo",                     \
-		  "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
-	);                                                                    \
-	_arg4 ? -_num : _num;                                                 \
-})
-
-#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
-({                                                                            \
-	register long _num asm("v0") = (num);                                 \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-	register long _arg4 asm("a3") = (long)(arg4);                         \
-	register long _arg5 = (long)(arg5);				      \
-									      \
-	asm volatile (                                                        \
-		"addiu $sp, $sp, -32\n"                                       \
-		"sw %7, 16($sp)\n"                                            \
-		"syscall\n  "                                                 \
-		"addiu $sp, $sp, 32\n"                                        \
-		: "=r" (_num), "=r"(_arg4)                                    \
-		: "0"(_num),                                                  \
-		  "r"(_arg1), "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5)  \
-		: "memory", "cc", "at", "v1", "hi", "lo",                     \
-		  "t0", "t1", "t2", "t3", "t4", "t5", "t6", "t7", "t8", "t9"  \
-	);                                                                    \
-	_arg4 ? -_num : _num;                                                 \
-})
-
-/* startup code, note that it's called __start on MIPS */
-asm(".section .text\n"
-    ".set nomips16\n"
-    ".global __start\n"
-    ".set    noreorder\n"
-    ".option pic0\n"
-    ".ent __start\n"
-    "__start:\n"
-    "lw $a0,($sp)\n"              // argc was in the stack
-    "addiu  $a1, $sp, 4\n"        // argv = sp + 4
-    "sll $a2, $a0, 2\n"           // a2 = argc * 4
-    "add   $a2, $a2, $a1\n"       // envp = argv + 4*argc ...
-    "addiu $a2, $a2, 4\n"         //        ... + 4
-    "li $t0, -8\n"
-    "and $sp, $sp, $t0\n"         // sp must be 8-byte aligned
-    "addiu $sp,$sp,-16\n"         // the callee expects to save a0..a3 there!
-    "jal main\n"                  // main() returns the status code, we'll exit with it.
-    "nop\n"                       // delayed slot
-    "and $a0, $v0, 0xff\n"        // limit exit code to 8 bits
-    "li $v0, 4001\n"              // NR_exit == 4001
-    "syscall\n"
-    ".end __start\n"
-    "");
-
-/* fcntl / open */
-#define O_RDONLY            0
-#define O_WRONLY            1
-#define O_RDWR              2
-#define O_APPEND       0x0008
-#define O_NONBLOCK     0x0080
-#define O_CREAT        0x0100
-#define O_TRUNC        0x0200
-#define O_EXCL         0x0400
-#define O_NOCTTY       0x0800
-#define O_DIRECTORY   0x10000
-
-/* The struct returned by the stat() syscall. 88 bytes are returned by the
- * syscall.
- */
-struct sys_stat_struct {
-	unsigned int  st_dev;
-	long          st_pad1[3];
-	unsigned long st_ino;
-	unsigned int  st_mode;
-	unsigned int  st_nlink;
-	unsigned int  st_uid;
-	unsigned int  st_gid;
-	unsigned int  st_rdev;
-	long          st_pad2[2];
-	long          st_size;
-	long          st_pad3;
-	long          st_atime;
-	long          st_atime_nsec;
-	long          st_mtime;
-	long          st_mtime_nsec;
-	long          st_ctime;
-	long          st_ctime_nsec;
-	long          st_blksize;
-	long          st_blocks;
-	long          st_pad4[14];
-};
-
-#elif defined(__riscv)
-
-#if   __riscv_xlen == 64
-#define PTRLOG "3"
-#define SZREG  "8"
-#elif __riscv_xlen == 32
-#define PTRLOG "2"
-#define SZREG  "4"
-#endif
-
-/* Syscalls for RISCV :
- *   - stack is 16-byte aligned
- *   - syscall number is passed in a7
- *   - arguments are in a0, a1, a2, a3, a4, a5
- *   - the system call is performed by calling ecall
- *   - syscall return comes in a0
- *   - the arguments are cast to long and assigned into the target
- *     registers which are then simply passed as registers to the asm code,
- *     so that we don't have to experience issues with register constraints.
- */
-
-#define my_syscall0(num)                                                      \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0");                                        \
-									      \
-	asm volatile (                                                        \
-		"ecall\n\t"                                                   \
-		: "=r"(_arg1)                                                 \
-		: "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall1(num, arg1)                                                \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);		              \
-									      \
-	asm volatile (                                                        \
-		"ecall\n"                                                     \
-		: "+r"(_arg1)                                                 \
-		: "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall2(num, arg1, arg2)                                          \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-									      \
-	asm volatile (                                                        \
-		"ecall\n"                                                     \
-		: "+r"(_arg1)                                                 \
-		: "r"(_arg2),                                                 \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall3(num, arg1, arg2, arg3)                                    \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-									      \
-	asm volatile (                                                        \
-		"ecall\n\t"                                                   \
-		: "+r"(_arg1)                                                 \
-		: "r"(_arg2), "r"(_arg3),                                     \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall4(num, arg1, arg2, arg3, arg4)                              \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-	register long _arg4 asm("a3") = (long)(arg4);                         \
-									      \
-	asm volatile (                                                        \
-		"ecall\n"                                                     \
-		: "+r"(_arg1)                                                 \
-		: "r"(_arg2), "r"(_arg3), "r"(_arg4),                         \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall5(num, arg1, arg2, arg3, arg4, arg5)                        \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-	register long _arg4 asm("a3") = (long)(arg4);                         \
-	register long _arg5 asm("a4") = (long)(arg5);                         \
-									      \
-	asm volatile (                                                        \
-		"ecall\n"                                                     \
-		: "+r"(_arg1)                                                 \
-		: "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5),             \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-#define my_syscall6(num, arg1, arg2, arg3, arg4, arg5, arg6)                  \
-({                                                                            \
-	register long _num  asm("a7") = (num);                                \
-	register long _arg1 asm("a0") = (long)(arg1);                         \
-	register long _arg2 asm("a1") = (long)(arg2);                         \
-	register long _arg3 asm("a2") = (long)(arg3);                         \
-	register long _arg4 asm("a3") = (long)(arg4);                         \
-	register long _arg5 asm("a4") = (long)(arg5);                         \
-	register long _arg6 asm("a5") = (long)(arg6);                         \
-									      \
-	asm volatile (                                                        \
-		"ecall\n"                                                     \
-		: "+r"(_arg1)                                                 \
-		: "r"(_arg2), "r"(_arg3), "r"(_arg4), "r"(_arg5), "r"(_arg6), \
-		  "r"(_num)                                                   \
-		: "memory", "cc"                                              \
-	);                                                                    \
-	_arg1;                                                                \
-})
-
-/* startup code */
-asm(".section .text\n"
-    ".global _start\n"
-    "_start:\n"
-    ".option push\n"
-    ".option norelax\n"
-    "lla   gp, __global_pointer$\n"
-    ".option pop\n"
-    "ld    a0, 0(sp)\n"          // argc (a0) was in the stack
-    "add   a1, sp, "SZREG"\n"    // argv (a1) = sp
-    "slli  a2, a0, "PTRLOG"\n"   // envp (a2) = SZREG*argc ...
-    "add   a2, a2, "SZREG"\n"    //             + SZREG (skip null)
-    "add   a2,a2,a1\n"           //             + argv
-    "andi  sp,a1,-16\n"          // sp must be 16-byte aligned
-    "call  main\n"               // main() returns the status code, we'll exit with it.
-    "andi  a0, a0, 0xff\n"       // limit exit code to 8 bits
-    "li a7, 93\n"                // NR_exit == 93
-    "ecall\n"
-    "");
-
-/* fcntl / open */
-#define O_RDONLY            0
-#define O_WRONLY            1
-#define O_RDWR              2
-#define O_CREAT         0x100
-#define O_EXCL          0x200
-#define O_NOCTTY        0x400
-#define O_TRUNC        0x1000
-#define O_APPEND       0x2000
-#define O_NONBLOCK     0x4000
-#define O_DIRECTORY  0x200000
-
-struct sys_stat_struct {
-	unsigned long	st_dev;		/* Device.  */
-	unsigned long	st_ino;		/* File serial number.  */
-	unsigned int	st_mode;	/* File mode.  */
-	unsigned int	st_nlink;	/* Link count.  */
-	unsigned int	st_uid;		/* User ID of the file's owner.  */
-	unsigned int	st_gid;		/* Group ID of the file's group. */
-	unsigned long	st_rdev;	/* Device number, if device.  */
-	unsigned long	__pad1;
-	long		st_size;	/* Size of file, in bytes.  */
-	int		st_blksize;	/* Optimal block size for I/O.  */
-	int		__pad2;
-	long		st_blocks;	/* Number 512-byte blocks allocated. */
-	long		st_atime;	/* Time of last access.  */
-	unsigned long	st_atime_nsec;
-	long		st_mtime;	/* Time of last modification.  */
-	unsigned long	st_mtime_nsec;
-	long		st_ctime;	/* Time of last status change.  */
-	unsigned long	st_ctime_nsec;
-	unsigned int	__unused4;
-	unsigned int	__unused5;
-};
-
-#endif
-
 
 /* Below are the C functions used to declare the raw syscalls. They try to be
  * architecture-agnostic, and return either a success or -errno. Declaring them
@@ -2397,9 +1093,9 @@
 int memcmp(const void *s1, const void *s2, size_t n)
 {
 	size_t ofs = 0;
-	char c1 = 0;
+	int c1 = 0;
 
-	while (ofs < n && !(c1 = ((char *)s1)[ofs] - ((char *)s2)[ofs])) {
+	while (ofs < n && !(c1 = ((unsigned char *)s1)[ofs] - ((unsigned char *)s2)[ofs])) {
 		ofs++;
 	}
 	return c1;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/std.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/std.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * Standard definitions and types for NOLIBC
+ * Copyright (C) 2017-2021 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_STD_H
+#define _NOLIBC_STD_H
+
+/* Declare a few quite common macros and types that usually are in stdlib.h,
+ * stdint.h, ctype.h, unistd.h and a few other common locations. Please place
+ * integer type definitions and generic macros here, but avoid OS-specific and
+ * syscall-specific stuff, as this file is expected to be included very early.
+ */
+
+/* note: may already be defined */
+#ifndef NULL
+#define NULL ((void *)0)
+#endif
+
+/* stdint types */
+typedef unsigned char       uint8_t;
+typedef   signed char        int8_t;
+typedef unsigned short     uint16_t;
+typedef   signed short      int16_t;
+typedef unsigned int       uint32_t;
+typedef   signed int        int32_t;
+typedef unsigned long long uint64_t;
+typedef   signed long long  int64_t;
+typedef unsigned long        size_t;
+typedef   signed long       ssize_t;
+typedef unsigned long     uintptr_t;
+typedef   signed long      intptr_t;
+typedef   signed long     ptrdiff_t;
+
+/* those are commonly provided by sys/types.h */
+typedef unsigned int          dev_t;
+typedef unsigned long         ino_t;
+typedef unsigned int         mode_t;
+typedef   signed int          pid_t;
+typedef unsigned int          uid_t;
+typedef unsigned int          gid_t;
+typedef unsigned long       nlink_t;
+typedef   signed long         off_t;
+typedef   signed long     blksize_t;
+typedef   signed long      blkcnt_t;
+typedef   signed long        time_t;
+
+#endif /* _NOLIBC_STD_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/nolibc/types.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/nolibc/types.h
@@ -0,0 +1,133 @@
+/* SPDX-License-Identifier: LGPL-2.1 OR MIT */
+/*
+ * Special types used by various syscalls for NOLIBC
+ * Copyright (C) 2017-2021 Willy Tarreau <w@1wt.eu>
+ */
+
+#ifndef _NOLIBC_TYPES_H
+#define _NOLIBC_TYPES_H
+
+#include "std.h"
+#include <linux/time.h>
+
+
+/* Only the generic macros and types may be defined here. The arch-specific
+ * ones such as the O_RDONLY and related macros used by fcntl() and open(), or
+ * the layout of sys_stat_struct must not be defined here.
+ */
+
+/* stat flags (WARNING, octal here) */
+#define S_IFDIR        0040000
+#define S_IFCHR        0020000
+#define S_IFBLK        0060000
+#define S_IFREG        0100000
+#define S_IFIFO        0010000
+#define S_IFLNK        0120000
+#define S_IFSOCK       0140000
+#define S_IFMT         0170000
+
+#define S_ISDIR(mode)  (((mode) & S_IFDIR)  == S_IFDIR)
+#define S_ISCHR(mode)  (((mode) & S_IFCHR)  == S_IFCHR)
+#define S_ISBLK(mode)  (((mode) & S_IFBLK)  == S_IFBLK)
+#define S_ISREG(mode)  (((mode) & S_IFREG)  == S_IFREG)
+#define S_ISFIFO(mode) (((mode) & S_IFIFO)  == S_IFIFO)
+#define S_ISLNK(mode)  (((mode) & S_IFLNK)  == S_IFLNK)
+#define S_ISSOCK(mode) (((mode) & S_IFSOCK) == S_IFSOCK)
+
+/* dirent types */
+#define DT_UNKNOWN     0x0
+#define DT_FIFO        0x1
+#define DT_CHR         0x2
+#define DT_DIR         0x4
+#define DT_BLK         0x6
+#define DT_REG         0x8
+#define DT_LNK         0xa
+#define DT_SOCK        0xc
+
+/* commonly an fd_set represents 256 FDs */
+#define FD_SETSIZE     256
+
+/* Special FD used by all the *at functions */
+#ifndef AT_FDCWD
+#define AT_FDCWD       (-100)
+#endif
+
+/* whence values for lseek() */
+#define SEEK_SET       0
+#define SEEK_CUR       1
+#define SEEK_END       2
+
+/* cmd for reboot() */
+#define LINUX_REBOOT_MAGIC1         0xfee1dead
+#define LINUX_REBOOT_MAGIC2         0x28121969
+#define LINUX_REBOOT_CMD_HALT       0xcdef0123
+#define LINUX_REBOOT_CMD_POWER_OFF  0x4321fedc
+#define LINUX_REBOOT_CMD_RESTART    0x01234567
+#define LINUX_REBOOT_CMD_SW_SUSPEND 0xd000fce2
+
+/* Macros used on waitpid()'s return status */
+#define WEXITSTATUS(status) (((status) & 0xff00) >> 8)
+#define WIFEXITED(status)   (((status) & 0x7f) == 0)
+
+
+/* for select() */
+typedef struct {
+	uint32_t fd32[FD_SETSIZE / 32];
+} fd_set;
+
+/* for poll() */
+struct pollfd {
+	int fd;
+	short int events;
+	short int revents;
+};
+
+/* for getdents64() */
+struct linux_dirent64 {
+	uint64_t       d_ino;
+	int64_t        d_off;
+	unsigned short d_reclen;
+	unsigned char  d_type;
+	char           d_name[];
+};
+
+/* needed by wait4() */
+struct rusage {
+	struct timeval ru_utime;
+	struct timeval ru_stime;
+	long   ru_maxrss;
+	long   ru_ixrss;
+	long   ru_idrss;
+	long   ru_isrss;
+	long   ru_minflt;
+	long   ru_majflt;
+	long   ru_nswap;
+	long   ru_inblock;
+	long   ru_oublock;
+	long   ru_msgsnd;
+	long   ru_msgrcv;
+	long   ru_nsignals;
+	long   ru_nvcsw;
+	long   ru_nivcsw;
+};
+
+/* The format of the struct as returned by the libc to the application, which
+ * significantly differs from the format returned by the stat() syscall flavours.
+ */
+struct stat {
+	dev_t     st_dev;     /* ID of device containing file */
+	ino_t     st_ino;     /* inode number */
+	mode_t    st_mode;    /* protection */
+	nlink_t   st_nlink;   /* number of hard links */
+	uid_t     st_uid;     /* user ID of owner */
+	gid_t     st_gid;     /* group ID of owner */
+	dev_t     st_rdev;    /* device ID (if special file) */
+	off_t     st_size;    /* total size, in bytes */
+	blksize_t st_blksize; /* blocksize for file system I/O */
+	blkcnt_t  st_blocks;  /* number of 512B blocks allocated */
+	time_t    st_atime;   /* time of last access */
+	time_t    st_mtime;   /* time of last modification */
+	time_t    st_ctime;   /* time of last status change */
+};
+
+#endif /* _NOLIBC_TYPES_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/tools/dis-asm-compat.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/tools/dis-asm-compat.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */
+#ifndef _TOOLS_DIS_ASM_COMPAT_H
+#define _TOOLS_DIS_ASM_COMPAT_H
+
+#include <stdio.h>
+#include <dis-asm.h>
+
+/* define types for older binutils version, to centralize ifdef'ery a bit */
+#ifndef DISASM_INIT_STYLED
+enum disassembler_style {DISASSEMBLER_STYLE_NOT_EMPTY};
+typedef int (*fprintf_styled_ftype) (void *, enum disassembler_style, const char*, ...);
+#endif
+
+/*
+ * Trivial fprintf wrapper to be used as the fprintf_styled_func argument to
+ * init_disassemble_info_compat() when normal fprintf suffices.
+ */
+static inline int fprintf_styled(void *out,
+				 enum disassembler_style style,
+				 const char *fmt, ...)
+{
+	va_list args;
+	int r;
+
+	(void)style;
+
+	va_start(args, fmt);
+	r = vfprintf(out, fmt, args);
+	va_end(args);
+
+	return r;
+}
+
+/*
+ * Wrapper for init_disassemble_info() that hides version
+ * differences. Depending on binutils version and architecture either
+ * fprintf_func or fprintf_styled_func will be called.
+ */
+static inline void init_disassemble_info_compat(struct disassemble_info *info,
+						void *stream,
+						fprintf_ftype unstyled_func,
+						fprintf_styled_ftype styled_func)
+{
+#ifdef DISASM_INIT_STYLED
+	init_disassemble_info(info, stream,
+			      unstyled_func,
+			      styled_func);
+#else
+	(void)styled_func;
+	init_disassemble_info(info, stream,
+			      unstyled_func);
+#endif
+}
+
+#endif /* _TOOLS_DIS_ASM_COMPAT_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/uapi/asm/errno.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/uapi/asm/errno.h
@@ -9,8 +9,8 @@
 #include "../../../arch/alpha/include/uapi/asm/errno.h"
 #elif defined(__mips__)
 #include "../../../arch/mips/include/uapi/asm/errno.h"
-#elif defined(__xtensa__)
-#include "../../../arch/xtensa/include/uapi/asm/errno.h"
+#elif defined(__hppa__)
+#include "../../../arch/parisc/include/uapi/asm/errno.h"
 #else
 #include <asm-generic/errno.h>
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/uapi/linux/bpf.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/uapi/linux/bpf.h
@@ -1762,7 +1762,9 @@
  * 		performed again, if the helper is used in combination with
  * 		direct packet access.
  * 	Return
- * 		0 on success, or a negative error in case of failure.
+ * 		0 on success, or a negative error in case of failure. Positive
+ * 		error indicates a potential drop or congestion in the target
+ * 		device. The particular positive error codes are not defined.
  *
  * u64 bpf_get_current_pid_tgid(void)
  * 	Return
@@ -2276,8 +2278,8 @@
  * 	Return
  * 		The return value depends on the result of the test, and can be:
  *
- *		* 0, if current task belongs to the cgroup2.
- *		* 1, if current task does not belong to the cgroup2.
+ *		* 1, if current task belongs to the cgroup2.
+ *		* 0, if current task does not belong to the cgroup2.
  * 		* A negative error code, if an error occurred.
  *
  * long bpf_skb_change_tail(struct sk_buff *skb, u32 len, u64 flags)
@@ -3009,9 +3011,23 @@
  *		**BPF_FIB_LOOKUP_DIRECT**
  *			Do a direct table lookup vs full lookup using FIB
  *			rules.
+ *		**BPF_FIB_LOOKUP_TBID**
+ *			Used with BPF_FIB_LOOKUP_DIRECT.
+ *			Use the routing table ID present in *params*->tbid
+ *			for the fib lookup.
  *		**BPF_FIB_LOOKUP_OUTPUT**
  *			Perform lookup from an egress perspective (default is
  *			ingress).
+ *		**BPF_FIB_LOOKUP_SKIP_NEIGH**
+ *			Skip the neighbour table lookup. *params*->dmac
+ *			and *params*->smac will not be set as output. A common
+ *			use case is to call **bpf_redirect_neigh**\ () after
+ *			doing **bpf_fib_lookup**\ ().
+ *		**BPF_FIB_LOOKUP_SRC**
+ *			Derive and set source IP addr in *params*->ipv{4,6}_src
+ *			for the nexthop. If the src addr cannot be derived,
+ *			**BPF_FIB_LKUP_RET_NO_SRC_ADDR** is returned. In this
+ *			case, *params*->dmac and *params*->smac are not set either.
  *
  *		*ctx* is either **struct xdp_md** for XDP programs or
  *		**struct sk_buff** tc cls_act programs.
@@ -4243,6 +4259,8 @@
  * long bpf_get_task_stack(struct task_struct *task, void *buf, u32 size, u64 flags)
  *	Description
  *		Return a user or a kernel stack in bpf program provided buffer.
+ *		Note: the user stack will only be populated if the *task* is
+ *		the current task; all other tasks will return -EOPNOTSUPP.
  *		To achieve this, the helper needs *task*, which is a valid
  *		pointer to **struct task_struct**. To store the stacktrace, the
  *		bpf program provides *buf* with a nonnegative *size*.
@@ -4254,6 +4272,7 @@
  *
  *		**BPF_F_USER_STACK**
  *			Collect a user space stack instead of a kernel stack.
+ *			The *task* must be the current task.
  *		**BPF_F_USER_BUILD_ID**
  *			Collect buildid+offset instead of ips for user stack,
  *			only valid if **BPF_F_USER_STACK** is also specified.
@@ -5347,7 +5366,8 @@
 	__u32 src_ip4;
 	__u32 src_ip6[4];
 	__u32 src_port;		/* host byte order */
-	__u32 dst_port;		/* network byte order */
+	__be16 dst_port;	/* network byte order */
+	__u16 :16;		/* zero padding */
 	__u32 dst_ip4;
 	__u32 dst_ip6[4];
 	__u32 state;
@@ -6034,6 +6054,9 @@
 enum {
 	BPF_FIB_LOOKUP_DIRECT  = (1U << 0),
 	BPF_FIB_LOOKUP_OUTPUT  = (1U << 1),
+	BPF_FIB_LOOKUP_SKIP_NEIGH = (1U << 2),
+	BPF_FIB_LOOKUP_TBID    = (1U << 3),
+	BPF_FIB_LOOKUP_SRC     = (1U << 4),
 };
 
 enum {
@@ -6046,6 +6069,7 @@
 	BPF_FIB_LKUP_RET_UNSUPP_LWT,   /* fwd requires encapsulation */
 	BPF_FIB_LKUP_RET_NO_NEIGH,     /* no neighbor entry for nh */
 	BPF_FIB_LKUP_RET_FRAG_NEEDED,  /* fragmentation required to fwd */
+	BPF_FIB_LKUP_RET_NO_SRC_ADDR,  /* failed to derive IP src addr */
 };
 
 struct bpf_fib_lookup {
@@ -6065,7 +6089,7 @@
 
 		/* output: MTU value */
 		__u16	mtu_result;
-	};
+	} __attribute__((packed, aligned(2)));
 	/* input: L3 device index for lookup
 	 * output: device index from FIB lookup
 	 */
@@ -6080,6 +6104,9 @@
 		__u32	rt_metric;
 	};
 
+	/* input: source address to consider for lookup
+	 * output: source address result from lookup
+	 */
 	union {
 		__be32		ipv4_src;
 		__u32		ipv6_src[4];  /* in6_addr; network order */
@@ -6094,9 +6121,19 @@
 		__u32		ipv6_dst[4];  /* in6_addr; network order */
 	};
 
-	/* output */
-	__be16	h_vlan_proto;
-	__be16	h_vlan_TCI;
+	union {
+		struct {
+			/* output */
+			__be16	h_vlan_proto;
+			__be16	h_vlan_TCI;
+		};
+		/* input: when accompanied with the
+		 * 'BPF_FIB_LOOKUP_DIRECT | BPF_FIB_LOOKUP_TBID` flags, a
+		 * specific routing table to use for the fib lookup.
+		 */
+		__u32	tbid;
+	};
+
 	__u8	smac[6];     /* ETH_ALEN */
 	__u8	dmac[6];     /* ETH_ALEN */
 };
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/uapi/linux/fscrypt.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/uapi/linux/fscrypt.h
@@ -27,7 +27,8 @@
 #define FSCRYPT_MODE_AES_128_CBC		5
 #define FSCRYPT_MODE_AES_128_CTS		6
 #define FSCRYPT_MODE_ADIANTUM			9
-/* If adding a mode number > 9, update FSCRYPT_MODE_MAX in fscrypt_private.h */
+#define FSCRYPT_MODE_AES_256_HCTR2		10
+/* If adding a mode number > 10, update FSCRYPT_MODE_MAX in fscrypt_private.h */
 
 /*
  * Legacy policy version; ad-hoc KDF and no key verification.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/uapi/linux/if_link.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/uapi/linux/if_link.h
@@ -655,6 +655,7 @@
 	IFLA_BOND_TLB_DYNAMIC_LB,
 	IFLA_BOND_PEER_NOTIF_DELAY,
 	IFLA_BOND_AD_LACP_ACTIVE,
+	IFLA_BOND_MISSED_MAX,
 	__IFLA_BOND_MAX,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/uapi/linux/perf_event.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/uapi/linux/perf_event.h
@@ -251,6 +251,8 @@
 	PERF_BR_SYSRET		= 8,	/* syscall return */
 	PERF_BR_COND_CALL	= 9,	/* conditional function call */
 	PERF_BR_COND_RET	= 10,	/* conditional function return */
+	PERF_BR_ERET		= 11,	/* exception return */
+	PERF_BR_IRQ		= 12,	/* irq */
 	PERF_BR_MAX,
 };
 
@@ -299,6 +301,7 @@
  *	  { u64		time_enabled; } && PERF_FORMAT_TOTAL_TIME_ENABLED
  *	  { u64		time_running; } && PERF_FORMAT_TOTAL_TIME_RUNNING
  *	  { u64		id;           } && PERF_FORMAT_ID
+ *	  { u64		lost;         } && PERF_FORMAT_LOST
  *	} && !PERF_FORMAT_GROUP
  *
  *	{ u64		nr;
@@ -306,6 +309,7 @@
  *	  { u64		time_running; } && PERF_FORMAT_TOTAL_TIME_RUNNING
  *	  { u64		value;
  *	    { u64	id;           } && PERF_FORMAT_ID
+ *	    { u64	lost;         } && PERF_FORMAT_LOST
  *	  }		cntr[nr];
  *	} && PERF_FORMAT_GROUP
  * };
@@ -315,8 +319,9 @@
 	PERF_FORMAT_TOTAL_TIME_RUNNING		= 1U << 1,
 	PERF_FORMAT_ID				= 1U << 2,
 	PERF_FORMAT_GROUP			= 1U << 3,
+	PERF_FORMAT_LOST			= 1U << 4,
 
-	PERF_FORMAT_MAX = 1U << 4,		/* non-ABI */
+	PERF_FORMAT_MAX = 1U << 5,		/* non-ABI */
 };
 
 #define PERF_ATTR_SIZE_VER0	64	/* sizeof first published struct */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/include/uapi/sound/asound.h
+++ linux-xilinx-zynqmp-5.15.0/tools/include/uapi/sound/asound.h
@@ -56,8 +56,10 @@
  *                                                                          *
  ****************************************************************************/
 
+#define AES_IEC958_STATUS_SIZE		24
+
 struct snd_aes_iec958 {
-	unsigned char status[24];	/* AES/IEC958 channel status bits */
+	unsigned char status[AES_IEC958_STATUS_SIZE]; /* AES/IEC958 channel status bits */
 	unsigned char subcode[147];	/* AES/IEC958 subcode bits */
 	unsigned char pad;		/* nothing */
 	unsigned char dig_subframe[4];	/* AES/IEC958 subframe bits */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/kvm/kvm_stat/kvm_stat
+++ linux-xilinx-zynqmp-5.15.0/tools/kvm/kvm_stat/kvm_stat
@@ -1646,7 +1646,8 @@
                          .format(values))
             if len(pids) > 1:
                 sys.exit('Error: Multiple processes found (pids: {}). Use "-p"'
-                         ' to specify the desired pid'.format(" ".join(pids)))
+                         ' to specify the desired pid'
+                         .format(" ".join(map(str, pids))))
             namespace.pid = pids[0]
 
     argparser = argparse.ArgumentParser(description=description_text,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/api/io.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/api/io.h
@@ -9,6 +9,7 @@
 
 #include <stdlib.h>
 #include <unistd.h>
+#include <linux/types.h>
 
 struct io {
 	/* File descriptor being read/ */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/Makefile
@@ -126,7 +126,7 @@
 			   sort -u | wc -l)
 VERSIONED_SYM_COUNT = $(shell readelf --dyn-syms --wide $(OUTPUT)libbpf.so | \
 			      sed 's/\[.*\]//' | \
-			      awk '/GLOBAL/ && /DEFAULT/ && !/UND/ {print $$NF}' | \
+			      awk '/GLOBAL/ && /DEFAULT/ && !/UND|ABS/ {print $$NF}' | \
 			      grep -Eo '[^ ]+@LIBBPF_' | cut -d@ -f1 | sort -u | wc -l)
 
 CMD_TARGETS = $(LIB_TARGET) $(PC_FILE)
@@ -195,7 +195,7 @@
 		    sort -u > $(OUTPUT)libbpf_global_syms.tmp;		 \
 		readelf --dyn-syms --wide $(OUTPUT)libbpf.so |		 \
 		    sed 's/\[.*\]//' |					 \
-		    awk '/GLOBAL/ && /DEFAULT/ && !/UND/ {print $$NF}'|  \
+		    awk '/GLOBAL/ && /DEFAULT/ && !/UND|ABS/ {print $$NF}'|  \
 		    grep -Eo '[^ ]+@LIBBPF_' | cut -d@ -f1 |		 \
 		    sort -u > $(OUTPUT)libbpf_versioned_syms.tmp; 	 \
 		diff -u $(OUTPUT)libbpf_global_syms.tmp			 \
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/bpf.c
@@ -480,6 +480,7 @@
 int bpf_map_lookup_and_delete_elem_flags(int fd, const void *key, void *value, __u64 flags)
 {
 	union bpf_attr attr;
+	int ret;
 
 	memset(&attr, 0, sizeof(attr));
 	attr.map_fd = fd;
@@ -487,7 +488,8 @@
 	attr.value = ptr_to_u64(value);
 	attr.flags = flags;
 
-	return sys_bpf(BPF_MAP_LOOKUP_AND_DELETE_ELEM, &attr, sizeof(attr));
+	ret = sys_bpf(BPF_MAP_LOOKUP_AND_DELETE_ELEM, &attr, sizeof(attr));
+	return libbpf_err_errno(ret);
 }
 
 int bpf_map_delete_elem(int fd, const void *key)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/bpf.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/bpf.h
@@ -249,8 +249,15 @@
 				 __u32 *buf_len, __u32 *prog_id, __u32 *fd_type,
 				 __u64 *probe_offset, __u64 *probe_addr);
 
+#ifdef __cplusplus
+/* forward-declaring enums in C++ isn't compatible with pure C enums, so
+ * instead define bpf_enable_stats() as accepting int as an input
+ */
+LIBBPF_API int bpf_enable_stats(int type);
+#else
 enum bpf_stats_type; /* defined in up-to-date linux/bpf.h */
 LIBBPF_API int bpf_enable_stats(enum bpf_stats_type type);
+#endif
 
 struct bpf_prog_bind_opts {
 	size_t sz; /* size of this struct for forward/backward compatibility */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/bpf_core_read.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/bpf_core_read.h
@@ -40,7 +40,7 @@
 #define __CORE_RELO(src, field, info)					      \
 	__builtin_preserve_field_info((src)->field, BPF_FIELD_##info)
 
-#if __BYTE_ORDER == __LITTLE_ENDIAN
+#if __BYTE_ORDER__ == __ORDER_LITTLE_ENDIAN__
 #define __CORE_BITFIELD_PROBE_READ(dst, src, fld)			      \
 	bpf_probe_read_kernel(						      \
 			(void *)dst,				      \
@@ -101,6 +101,7 @@
 	case 2: val = *(const unsigned short *)p; break;		      \
 	case 4: val = *(const unsigned int *)p; break;			      \
 	case 8: val = *(const unsigned long long *)p; break;		      \
+	default: val = 0; break;					      \
 	}								      \
 	val <<= __CORE_RELO(s, field, LSHIFT_U64);			      \
 	if (__CORE_RELO(s, field, SIGNED))				      \
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/bpf_helpers.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/bpf_helpers.h
@@ -72,16 +72,21 @@
 /*
  * Helper macros to manipulate data structures
  */
-#ifndef offsetof
-#define offsetof(TYPE, MEMBER)	((unsigned long)&((TYPE *)0)->MEMBER)
-#endif
-#ifndef container_of
+
+/* offsetof() definition that uses __builtin_offset() might not preserve field
+ * offset CO-RE relocation properly, so force-redefine offsetof() using
+ * old-school approach which works with CO-RE correctly
+ */
+#undef offsetof
+#define offsetof(type, member)	((unsigned long)&((type *)0)->member)
+
+/* redefined container_of() to ensure we use the above offsetof() macro */
+#undef container_of
 #define container_of(ptr, type, member)				\
 	({							\
 		void *__mptr = (void *)(ptr);			\
 		((type *)(__mptr - offsetof(type, member)));	\
 	})
-#endif
 
 /*
  * Helper macro to throw a compilation error if __bpf_unreachable() gets
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/btf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/btf.c
@@ -231,17 +231,23 @@
 		}
 		btf_bswap_hdr(hdr);
 	} else if (hdr->magic != BTF_MAGIC) {
-		pr_debug("Invalid BTF magic:%x\n", hdr->magic);
+		pr_debug("Invalid BTF magic: %x\n", hdr->magic);
 		return -EINVAL;
 	}
 
-	meta_left = btf->raw_size - sizeof(*hdr);
-	if (meta_left < hdr->str_off + hdr->str_len) {
-		pr_debug("Invalid BTF total size:%u\n", btf->raw_size);
+	if (btf->raw_size < hdr->hdr_len) {
+		pr_debug("BTF header len %u larger than data size %u\n",
+			 hdr->hdr_len, btf->raw_size);
 		return -EINVAL;
 	}
 
-	if (hdr->type_off + hdr->type_len > hdr->str_off) {
+	meta_left = btf->raw_size - hdr->hdr_len;
+	if (meta_left < (long long)hdr->str_off + hdr->str_len) {
+		pr_debug("Invalid BTF total size: %u\n", btf->raw_size);
+		return -EINVAL;
+	}
+
+	if ((long long)hdr->type_off + hdr->type_len > hdr->str_off) {
 		pr_debug("Invalid BTF data sections layout: type data at %u + %u, strings data at %u + %u\n",
 			 hdr->type_off, hdr->type_len, hdr->str_off, hdr->str_len);
 		return -EINVAL;
@@ -641,8 +647,21 @@
 			if (align <= 0)
 				return libbpf_err(align);
 			max_align = max(max_align, align);
+
+			/* if field offset isn't aligned according to field
+			 * type's alignment, then struct must be packed
+			 */
+			if (btf_member_bitfield_size(t, i) == 0 &&
+			    (m->offset % (8 * align)) != 0)
+				return 1;
 		}
 
+		/* if struct/union size isn't a multiple of its alignment,
+		 * then struct must be packed
+		 */
+		if ((t->size % max_align) != 0)
+			return 1;
+
 		return max_align;
 	}
 	default:
@@ -2620,15 +2639,11 @@
 	free(btf_ext);
 }
 
-struct btf_ext *btf_ext__new(__u8 *data, __u32 size)
+struct btf_ext *btf_ext__new(const __u8 *data, __u32 size)
 {
 	struct btf_ext *btf_ext;
 	int err;
 
-	err = btf_ext_parse_hdr(data, size);
-	if (err)
-		return libbpf_err_ptr(err);
-
 	btf_ext = calloc(1, sizeof(struct btf_ext));
 	if (!btf_ext)
 		return libbpf_err_ptr(-ENOMEM);
@@ -2641,6 +2656,10 @@
 	}
 	memcpy(btf_ext->data, data, size);
 
+	err = btf_ext_parse_hdr(btf_ext->data, size);
+	if (err)
+		goto done;
+
 	if (btf_ext->hdr->hdr_len < offsetofend(struct btf_ext_header, line_info_len)) {
 		err = -EINVAL;
 		goto done;
@@ -2914,8 +2933,10 @@
 		return libbpf_err(-EINVAL);
 	}
 
-	if (btf_ensure_modifiable(btf))
-		return libbpf_err(-ENOMEM);
+	if (btf_ensure_modifiable(btf)) {
+		err = -ENOMEM;
+		goto done;
+	}
 
 	err = btf_dedup_prep(d);
 	if (err) {
@@ -3350,8 +3371,8 @@
 }
 
 /*
- * Check structural compatibility of two FUNC_PROTOs, ignoring referenced type
- * IDs. This check is performed during type graph equivalence check and
+ * Check structural compatibility of two STRUCTs/UNIONs, ignoring referenced
+ * type IDs. This check is performed during type graph equivalence check and
  * referenced types equivalence is checked separately.
  */
 static bool btf_shallow_equal_struct(struct btf_type *t1, struct btf_type *t2)
@@ -3710,18 +3731,45 @@
 }
 
 /* Check if given two types are identical ARRAY definitions */
-static int btf_dedup_identical_arrays(struct btf_dedup *d, __u32 id1, __u32 id2)
+static bool btf_dedup_identical_arrays(struct btf_dedup *d, __u32 id1, __u32 id2)
 {
 	struct btf_type *t1, *t2;
 
 	t1 = btf_type_by_id(d->btf, id1);
 	t2 = btf_type_by_id(d->btf, id2);
 	if (!btf_is_array(t1) || !btf_is_array(t2))
-		return 0;
+		return false;
 
 	return btf_equal_array(t1, t2);
 }
 
+/* Check if given two types are identical STRUCT/UNION definitions */
+static bool btf_dedup_identical_structs(struct btf_dedup *d, __u32 id1, __u32 id2)
+{
+	const struct btf_member *m1, *m2;
+	struct btf_type *t1, *t2;
+	int n, i;
+
+	t1 = btf_type_by_id(d->btf, id1);
+	t2 = btf_type_by_id(d->btf, id2);
+
+	if (!btf_is_composite(t1) || btf_kind(t1) != btf_kind(t2))
+		return false;
+
+	if (!btf_shallow_equal_struct(t1, t2))
+		return false;
+
+	m1 = btf_members(t1);
+	m2 = btf_members(t2);
+	for (i = 0, n = btf_vlen(t1); i < n; i++, m1++, m2++) {
+		if (m1->type != m2->type &&
+		    !btf_dedup_identical_arrays(d, m1->type, m2->type) &&
+		    !btf_dedup_identical_structs(d, m1->type, m2->type))
+			return false;
+	}
+	return true;
+}
+
 /*
  * Check equivalence of BTF type graph formed by candidate struct/union (we'll
  * call it "candidate graph" in this description for brevity) to a type graph
@@ -3833,6 +3881,8 @@
 
 	hypot_type_id = d->hypot_map[canon_id];
 	if (hypot_type_id <= BTF_MAX_NR_TYPES) {
+		if (hypot_type_id == cand_id)
+			return 1;
 		/* In some cases compiler will generate different DWARF types
 		 * for *identical* array type definitions and use them for
 		 * different fields within the *same* struct. This breaks type
@@ -3841,8 +3891,18 @@
 		 * types within a single CU. So work around that by explicitly
 		 * allowing identical array types here.
 		 */
-		return hypot_type_id == cand_id ||
-		       btf_dedup_identical_arrays(d, hypot_type_id, cand_id);
+		if (btf_dedup_identical_arrays(d, hypot_type_id, cand_id))
+			return 1;
+		/* It turns out that similar situation can happen with
+		 * struct/union sometimes, sigh... Handle the case where
+		 * structs/unions are exactly the same, down to the referenced
+		 * type IDs. Anything more complicated (e.g., if referenced
+		 * types are different, but equivalent) is *way more*
+		 * complicated and requires a many-to-many equivalence mapping.
+		 */
+		if (btf_dedup_identical_structs(d, hypot_type_id, cand_id))
+			return 1;
+		return 0;
 	}
 
 	if (btf_dedup_hypot_map_add(d, canon_id, cand_id))
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/btf.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/btf.h
@@ -80,7 +80,7 @@
 				    __u32 expected_value_size,
 				    __u32 *key_type_id, __u32 *value_type_id);
 
-LIBBPF_API struct btf_ext *btf_ext__new(__u8 *data, __u32 size);
+LIBBPF_API struct btf_ext *btf_ext__new(const __u8 *data, __u32 size);
 LIBBPF_API void btf_ext__free(struct btf_ext *btf_ext);
 LIBBPF_API const void *btf_ext__get_raw_data(const struct btf_ext *btf_ext,
 					     __u32 *size);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/btf_dump.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/btf_dump.c
@@ -215,6 +215,17 @@
 	return 0;
 }
 
+static void btf_dump_free_names(struct hashmap *map)
+{
+	size_t bkt;
+	struct hashmap_entry *cur;
+
+	hashmap__for_each_entry(map, cur, bkt)
+		free((void *)cur->key);
+
+	hashmap__free(map);
+}
+
 void btf_dump__free(struct btf_dump *d)
 {
 	int i;
@@ -233,8 +244,8 @@
 	free(d->cached_names);
 	free(d->emit_queue);
 	free(d->decl_stack);
-	hashmap__free(d->type_names);
-	hashmap__free(d->ident_names);
+	btf_dump_free_names(d->type_names);
+	btf_dump_free_names(d->ident_names);
 
 	free(d);
 }
@@ -810,14 +821,9 @@
 				 const struct btf_type *t)
 {
 	const struct btf_member *m;
-	int align, i, bit_sz;
+	int max_align = 1, align, i, bit_sz;
 	__u16 vlen;
 
-	align = btf__align_of(btf, id);
-	/* size of a non-packed struct has to be a multiple of its alignment*/
-	if (align && t->size % align)
-		return true;
-
 	m = btf_members(t);
 	vlen = btf_vlen(t);
 	/* all non-bitfield fields have to be naturally aligned */
@@ -826,8 +832,11 @@
 		bit_sz = btf_member_bitfield_size(t, i);
 		if (align && bit_sz == 0 && m->offset % (8 * align) != 0)
 			return true;
+		max_align = max(align, max_align);
 	}
-
+	/* size of a non-packed struct has to be a multiple of its alignment */
+	if (t->size % max_align != 0)
+		return true;
 	/*
 	 * if original struct was marked as packed, but its layout is
 	 * naturally aligned, we'll detect that it's not packed
@@ -835,44 +844,97 @@
 	return false;
 }
 
-static int chip_away_bits(int total, int at_most)
-{
-	return total % at_most ? : at_most;
-}
-
 static void btf_dump_emit_bit_padding(const struct btf_dump *d,
-				      int cur_off, int m_off, int m_bit_sz,
-				      int align, int lvl)
+				      int cur_off, int next_off, int next_align,
+				      bool in_bitfield, int lvl)
 {
-	int off_diff = m_off - cur_off;
-	int ptr_bits = d->ptr_sz * 8;
+	const struct {
+		const char *name;
+		int bits;
+	} pads[] = {
+		{"long", d->ptr_sz * 8}, {"int", 32}, {"short", 16}, {"char", 8}
+	};
+	int new_off, pad_bits, bits, i;
+	const char *pad_type;
+
+	if (cur_off >= next_off)
+		return; /* no gap */
+
+	/* For filling out padding we want to take advantage of
+	 * natural alignment rules to minimize unnecessary explicit
+	 * padding. First, we find the largest type (among long, int,
+	 * short, or char) that can be used to force naturally aligned
+	 * boundary. Once determined, we'll use such type to fill in
+	 * the remaining padding gap. In some cases we can rely on
+	 * compiler filling some gaps, but sometimes we need to force
+	 * alignment to close natural alignment with markers like
+	 * `long: 0` (this is always the case for bitfields).  Note
+	 * that even if struct itself has, let's say 4-byte alignment
+	 * (i.e., it only uses up to int-aligned types), using `long:
+	 * X;` explicit padding doesn't actually change struct's
+	 * overall alignment requirements, but compiler does take into
+	 * account that type's (long, in this example) natural
+	 * alignment requirements when adding implicit padding. We use
+	 * this fact heavily and don't worry about ruining correct
+	 * struct alignment requirement.
+	 */
+	for (i = 0; i < ARRAY_SIZE(pads); i++) {
+		pad_bits = pads[i].bits;
+		pad_type = pads[i].name;
+
+		new_off = roundup(cur_off, pad_bits);
+		if (new_off <= next_off)
+			break;
+	}
 
-	if (off_diff <= 0)
-		/* no gap */
-		return;
-	if (m_bit_sz == 0 && off_diff < align * 8)
-		/* natural padding will take care of a gap */
-		return;
+	if (new_off > cur_off && new_off <= next_off) {
+		/* We need explicit `<type>: 0` aligning mark if next
+		 * field is right on alignment offset and its
+		 * alignment requirement is less strict than <type>'s
+		 * alignment (so compiler won't naturally align to the
+		 * offset we expect), or if subsequent `<type>: X`,
+		 * will actually completely fit in the remaining hole,
+		 * making compiler basically ignore `<type>: X`
+		 * completely.
+		 */
+		if (in_bitfield ||
+		    (new_off == next_off && roundup(cur_off, next_align * 8) != new_off) ||
+		    (new_off != next_off && next_off - new_off <= new_off - cur_off))
+			/* but for bitfields we'll emit explicit bit count */
+			btf_dump_printf(d, "\n%s%s: %d;", pfx(lvl), pad_type,
+					in_bitfield ? new_off - cur_off : 0);
+		cur_off = new_off;
+	}
 
-	while (off_diff > 0) {
-		const char *pad_type;
-		int pad_bits;
-
-		if (ptr_bits > 32 && off_diff > 32) {
-			pad_type = "long";
-			pad_bits = chip_away_bits(off_diff, ptr_bits);
-		} else if (off_diff > 16) {
-			pad_type = "int";
-			pad_bits = chip_away_bits(off_diff, 32);
-		} else if (off_diff > 8) {
-			pad_type = "short";
-			pad_bits = chip_away_bits(off_diff, 16);
-		} else {
-			pad_type = "char";
-			pad_bits = chip_away_bits(off_diff, 8);
+	/* Now we know we start at naturally aligned offset for a chosen
+	 * padding type (long, int, short, or char), and so the rest is just
+	 * a straightforward filling of remaining padding gap with full
+	 * `<type>: sizeof(<type>);` markers, except for the last one, which
+	 * might need smaller than sizeof(<type>) padding.
+	 */
+	while (cur_off != next_off) {
+		bits = min(next_off - cur_off, pad_bits);
+		if (bits == pad_bits) {
+			btf_dump_printf(d, "\n%s%s: %d;", pfx(lvl), pad_type, pad_bits);
+			cur_off += bits;
+			continue;
+		}
+		/* For the remainder padding that doesn't cover entire
+		 * pad_type bit length, we pick the smallest necessary type.
+		 * This is pure aesthetics, we could have just used `long`,
+		 * but having smallest necessary one communicates better the
+		 * scale of the padding gap.
+		 */
+		for (i = ARRAY_SIZE(pads) - 1; i >= 0; i--) {
+			pad_type = pads[i].name;
+			pad_bits = pads[i].bits;
+			if (pad_bits < bits)
+				continue;
+
+			btf_dump_printf(d, "\n%s%s: %d;", pfx(lvl), pad_type, bits);
+			cur_off += bits;
+			break;
 		}
-		btf_dump_printf(d, "\n%s%s: %d;", pfx(lvl), pad_type, pad_bits);
-		off_diff -= pad_bits;
 	}
 }
 
@@ -892,9 +954,11 @@
 {
 	const struct btf_member *m = btf_members(t);
 	bool is_struct = btf_is_struct(t);
-	int align, i, packed, off = 0;
+	bool packed, prev_bitfield = false;
+	int align, i, off = 0;
 	__u16 vlen = btf_vlen(t);
 
+	align = btf__align_of(d->btf, id);
 	packed = is_struct ? btf_is_struct_packed(d->btf, id, t) : 0;
 
 	btf_dump_printf(d, "%s%s%s {",
@@ -904,37 +968,47 @@
 
 	for (i = 0; i < vlen; i++, m++) {
 		const char *fname;
-		int m_off, m_sz;
+		int m_off, m_sz, m_align;
+		bool in_bitfield;
 
 		fname = btf_name_of(d, m->name_off);
 		m_sz = btf_member_bitfield_size(t, i);
 		m_off = btf_member_bit_offset(t, i);
-		align = packed ? 1 : btf__align_of(d->btf, m->type);
+		m_align = packed ? 1 : btf__align_of(d->btf, m->type);
+
+		in_bitfield = prev_bitfield && m_sz != 0;
 
-		btf_dump_emit_bit_padding(d, off, m_off, m_sz, align, lvl + 1);
+		btf_dump_emit_bit_padding(d, off, m_off, m_align, in_bitfield, lvl + 1);
 		btf_dump_printf(d, "\n%s", pfx(lvl + 1));
 		btf_dump_emit_type_decl(d, m->type, fname, lvl + 1);
 
 		if (m_sz) {
 			btf_dump_printf(d, ": %d", m_sz);
 			off = m_off + m_sz;
+			prev_bitfield = true;
 		} else {
 			m_sz = max((__s64)0, btf__resolve_size(d->btf, m->type));
 			off = m_off + m_sz * 8;
+			prev_bitfield = false;
 		}
+
 		btf_dump_printf(d, ";");
 	}
 
 	/* pad at the end, if necessary */
-	if (is_struct) {
-		align = packed ? 1 : btf__align_of(d->btf, id);
-		btf_dump_emit_bit_padding(d, off, t->size * 8, 0, align,
-					  lvl + 1);
-	}
+	if (is_struct)
+		btf_dump_emit_bit_padding(d, off, t->size * 8, align, false, lvl + 1);
 
-	if (vlen)
+	/*
+	 * Keep `struct empty {}` on a single line,
+	 * only print newline when there are regular or padding fields.
+	 */
+	if (vlen || t->size) {
 		btf_dump_printf(d, "\n");
-	btf_dump_printf(d, "%s}", pfx(lvl));
+		btf_dump_printf(d, "%s}", pfx(lvl));
+	} else {
+		btf_dump_printf(d, "}");
+	}
 	if (packed)
 		btf_dump_printf(d, " __attribute__((packed))");
 }
@@ -1384,10 +1458,12 @@
 			 * Clang for BPF target generates func_proto with no
 			 * args as a func_proto with a single void arg (e.g.,
 			 * `int (*f)(void)` vs just `int (*f)()`). We are
-			 * going to pretend there are no args for such case.
+			 * going to emit valid empty args (void) syntax for
+			 * such case. Similarly and conveniently, valid
+			 * no args case can be special-cased here as well.
 			 */
-			if (vlen == 1 && p->type == 0) {
-				btf_dump_printf(d, ")");
+			if (vlen == 0 || (vlen == 1 && p->type == 0)) {
+				btf_dump_printf(d, "void)");
 				return;
 			}
 
@@ -1457,11 +1533,23 @@
 static size_t btf_dump_name_dups(struct btf_dump *d, struct hashmap *name_map,
 				 const char *orig_name)
 {
+	char *old_name, *new_name;
 	size_t dup_cnt = 0;
+	int err;
+
+	new_name = strdup(orig_name);
+	if (!new_name)
+		return 1;
 
 	hashmap__find(name_map, orig_name, (void **)&dup_cnt);
 	dup_cnt++;
-	hashmap__set(name_map, orig_name, (void *)dup_cnt, NULL, NULL);
+
+	err = hashmap__set(name_map, new_name, (void *)dup_cnt,
+			   (const void **)&old_name, NULL);
+	if (err)
+		free(new_name);
+
+	free(old_name);
 
 	return dup_cnt;
 }
@@ -1481,6 +1569,11 @@
 	if (s->name_resolved)
 		return *cached_name ? *cached_name : orig_name;
 
+	if (btf_is_fwd(t) || (btf_is_enum(t) && btf_vlen(t) == 0)) {
+		s->name_resolved = 1;
+		return orig_name;
+	}
+
 	dup_cnt = btf_dump_name_dups(d, name_map, orig_name);
 	if (dup_cnt > 1) {
 		const size_t max_len = 256;
@@ -1829,14 +1922,16 @@
 {
 	const struct btf_array *array = btf_array(t);
 	const struct btf_type *elem_type;
-	__u32 i, elem_size = 0, elem_type_id;
+	__u32 i, elem_type_id;
+	__s64 elem_size;
 	bool is_array_member;
 
 	elem_type_id = array->type;
 	elem_type = skip_mods_and_typedefs(d->btf, elem_type_id, NULL);
 	elem_size = btf__resolve_size(d->btf, elem_type_id);
 	if (elem_size <= 0) {
-		pr_warn("unexpected elem size %d for array type [%u]\n", elem_size, id);
+		pr_warn("unexpected elem size %zd for array type [%u]\n",
+			(ssize_t)elem_size, id);
 		return -EINVAL;
 	}
 
@@ -1885,7 +1980,7 @@
 {
 	const struct btf_member *m = btf_members(t);
 	__u16 n = btf_vlen(t);
-	int i, err;
+	int i, err = 0;
 
 	/* note that we increment depth before calling btf_dump_print() below;
 	 * this is intentional.  btf_dump_data_newline() will not print a
@@ -2033,9 +2128,25 @@
 					     const struct btf_type *t,
 					     __u32 id,
 					     const void *data,
-					     __u8 bits_offset)
+					     __u8 bits_offset,
+					     __u8 bit_sz)
 {
-	__s64 size = btf__resolve_size(d->btf, id);
+	__s64 size;
+
+	if (bit_sz) {
+		/* bits_offset is at most 7. bit_sz is at most 128. */
+		__u8 nr_bytes = (bits_offset + bit_sz + 7) / 8;
+
+		/* When bit_sz is non zero, it is called from
+		 * btf_dump_struct_data() where it only cares about
+		 * negative error value.
+		 * Return nr_bytes in success case to make it
+		 * consistent as the regular integer case below.
+		 */
+		return data + nr_bytes > d->typed_dump->data_end ? -E2BIG : nr_bytes;
+	}
+
+	size = btf__resolve_size(d->btf, id);
 
 	if (size < 0 || size >= INT_MAX) {
 		pr_warn("unexpected size [%zu] for id [%u]\n",
@@ -2186,9 +2297,9 @@
 				   __u8 bits_offset,
 				   __u8 bit_sz)
 {
-	int size, err;
+	int size, err = 0;
 
-	size = btf_dump_type_data_check_overflow(d, t, id, data, bits_offset);
+	size = btf_dump_type_data_check_overflow(d, t, id, data, bits_offset, bit_sz);
 	if (size < 0)
 		return size;
 	err = btf_dump_type_data_check_zero(d, t, id, data, bits_offset, bit_sz);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/gen_loader.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/gen_loader.c
@@ -480,7 +480,7 @@
 	gen->attach_kind = kind;
 	ret = snprintf(gen->attach_target, sizeof(gen->attach_target), "%s%s",
 		       prefix, attach_name);
-	if (ret == sizeof(gen->attach_target))
+	if (ret >= sizeof(gen->attach_target))
 		gen->error = -ENOSPC;
 }
 
@@ -663,9 +663,11 @@
 	debug_ret(gen, "prog_load %s insn_cnt %d", attr.prog_name, attr.insn_cnt);
 	/* successful or not, close btf module FDs used in extern ksyms and attach_btf_obj_fd */
 	cleanup_relos(gen, insns);
-	if (gen->attach_kind)
+	if (gen->attach_kind) {
 		emit_sys_close_blob(gen,
 				    attr_field(prog_load_attr, attach_btf_obj_fd));
+		gen->attach_kind = 0;
+	}
 	emit_check_err(gen);
 	/* remember prog_fd in the stack, if successful */
 	emit(gen, BPF_STX_MEM(BPF_W, BPF_REG_10, BPF_REG_7,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/libbpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/libbpf.c
@@ -2993,6 +2993,12 @@
 		}
 	}
 
+	if (!obj->efile.symbols) {
+		pr_warn("elf: couldn't find symbol table in %s, stripped object file?\n",
+			obj->path);
+		return -ENOENT;
+	}
+
 	scn = NULL;
 	while ((scn = elf_nextscn(elf, scn)) != NULL) {
 		idx++;
@@ -3123,7 +3129,7 @@
 		return true;
 
 	/* global function */
-	return bind == STB_GLOBAL && type == STT_FUNC;
+	return (bind == STB_GLOBAL || bind == STB_WEAK) && type == STT_FUNC;
 }
 
 static int find_extern_btf_id(const struct btf *btf, const char *ext_name)
@@ -3757,6 +3763,9 @@
 	int l = 0, r = obj->nr_programs - 1, m;
 	struct bpf_program *prog;
 
+	if (!obj->nr_programs)
+		return NULL;
+
 	while (l < r) {
 		m = l + (r - l + 1) / 2;
 		prog = &obj->programs[m];
@@ -3794,6 +3803,8 @@
 
 	scn = elf_sec_by_idx(obj, sec_idx);
 	scn_data = elf_sec_data(obj, scn);
+	if (!scn_data)
+		return -LIBBPF_ERRNO__FORMAT;
 
 	relo_sec_name = elf_sec_str(obj, shdr->sh_name);
 	sec_name = elf_sec_name(obj, scn);
@@ -3936,7 +3947,7 @@
 int bpf_map__reuse_fd(struct bpf_map *map, int fd)
 {
 	struct bpf_map_info info = {};
-	__u32 len = sizeof(info);
+	__u32 len = sizeof(info), name_len;
 	int new_fd, err;
 	char *new_name;
 
@@ -3946,7 +3957,12 @@
 	if (err)
 		return libbpf_err(err);
 
-	new_name = strdup(info.name);
+	name_len = strlen(info.name);
+	if (name_len == BPF_OBJ_NAME_LEN - 1 && strncmp(map->name, info.name, name_len) == 0)
+		new_name = strdup(map->name);
+	else
+		new_name = strdup(info.name);
+
 	if (!new_name)
 		return libbpf_err(-errno);
 
@@ -5132,7 +5148,7 @@
 	 * relocated, so it's enough to just subtract in-section offset
 	 */
 	insn_idx = insn_idx - prog->sec_insn_off;
-	if (insn_idx > prog->insns_cnt)
+	if (insn_idx >= prog->insns_cnt)
 		return -EINVAL;
 	insn = &prog->insns[insn_idx];
 
@@ -5215,9 +5231,10 @@
 		 */
 		prog = NULL;
 		for (i = 0; i < obj->nr_programs; i++) {
-			prog = &obj->programs[i];
-			if (strcmp(prog->sec_name, sec_name) == 0)
+			if (strcmp(obj->programs[i].sec_name, sec_name) == 0) {
+				prog = &obj->programs[i];
 				break;
+			}
 		}
 		if (!prog) {
 			pr_warn("sec '%s': failed to find a BPF program\n", sec_name);
@@ -5232,10 +5249,17 @@
 			insn_idx = rec->insn_off / BPF_INSN_SZ;
 			prog = find_prog_by_sec_insn(obj, sec_idx, insn_idx);
 			if (!prog) {
-				pr_warn("sec '%s': failed to find program at insn #%d for CO-RE offset relocation #%d\n",
-					sec_name, insn_idx, i);
-				err = -EINVAL;
-				goto out;
+				/* When __weak subprog is "overridden" by another instance
+				 * of the subprog from a different object file, linker still
+				 * appends all the .BTF.ext info that used to belong to that
+				 * eliminated subprogram.
+				 * This is similar to what x86-64 linker does for relocations.
+				 * So just ignore such relocations just like we ignore
+				 * subprog instructions when discovering subprograms.
+				 */
+				pr_debug("sec '%s': skipping CO-RE relocation #%d for insn #%d belonging to eliminated weak subprogram\n",
+					 sec_name, i, insn_idx);
+				continue;
 			}
 			/* no need to apply CO-RE relocation if the program is
 			 * not going to be loaded
@@ -8670,7 +8694,10 @@
 		pr_warn("error: inner_map_fd already specified\n");
 		return libbpf_err(-EINVAL);
 	}
-	zfree(&map->inner_map);
+	if (map->inner_map) {
+		bpf_map__destroy(map->inner_map);
+		zfree(&map->inner_map);
+	}
 	map->inner_map_fd = fd;
 	return 0;
 }
@@ -8702,7 +8729,7 @@
 struct bpf_map *
 bpf_map__next(const struct bpf_map *prev, const struct bpf_object *obj)
 {
-	if (prev == NULL)
+	if (prev == NULL && obj != NULL)
 		return obj->maps;
 
 	return __bpf_map__iter(prev, obj, 1);
@@ -8711,7 +8738,7 @@
 struct bpf_map *
 bpf_map__prev(const struct bpf_map *next, const struct bpf_object *obj)
 {
-	if (next == NULL) {
+	if (next == NULL && obj != NULL) {
 		if (!obj->nr_maps)
 			return NULL;
 		return obj->maps + obj->nr_maps - 1;
@@ -10800,6 +10827,9 @@
 
 void bpf_object__destroy_skeleton(struct bpf_object_skeleton *s)
 {
+	if (!s)
+		return;
+
 	if (s->progs)
 		bpf_object__detach_skeleton(s);
 	if (s->obj)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/libbpf_probes.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/libbpf_probes.c
@@ -245,7 +245,7 @@
 	case BPF_MAP_TYPE_RINGBUF:
 		key_size = 0;
 		value_size = 0;
-		max_entries = 4096;
+		max_entries = sysconf(_SC_PAGE_SIZE);
 		break;
 	case BPF_MAP_TYPE_UNSPEC:
 	case BPF_MAP_TYPE_HASH:
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/linker.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/linker.c
@@ -211,6 +211,7 @@
 	}
 	free(linker->secs);
 
+	free(linker->glob_syms);
 	free(linker);
 }
 
@@ -396,6 +397,8 @@
 		pr_warn_elf("failed to create SYMTAB data");
 		return -EINVAL;
 	}
+	/* Ensure libelf translates byte-order of symbol records */
+	sec->data->d_type = ELF_T_SYM;
 
 	str_off = strset__add_str(linker->strtab_strs, sec->sec_name);
 	if (str_off < 0)
@@ -565,17 +568,15 @@
 	}
 	obj->elf = elf_begin(obj->fd, ELF_C_READ_MMAP, NULL);
 	if (!obj->elf) {
-		err = -errno;
 		pr_warn_elf("failed to parse ELF file '%s'", filename);
-		return err;
+		return -EINVAL;
 	}
 
 	/* Sanity check ELF file high-level properties */
 	ehdr = elf64_getehdr(obj->elf);
 	if (!ehdr) {
-		err = -errno;
 		pr_warn_elf("failed to get ELF header for %s", filename);
-		return err;
+		return -EINVAL;
 	}
 	if (ehdr->e_ident[EI_DATA] != host_endianness) {
 		err = -EOPNOTSUPP;
@@ -591,9 +592,8 @@
 	}
 
 	if (elf_getshdrstrndx(obj->elf, &obj->shstrs_sec_idx)) {
-		err = -errno;
 		pr_warn_elf("failed to get SHSTRTAB section index for %s", filename);
-		return err;
+		return -EINVAL;
 	}
 
 	scn = NULL;
@@ -603,26 +603,23 @@
 
 		shdr = elf64_getshdr(scn);
 		if (!shdr) {
-			err = -errno;
 			pr_warn_elf("failed to get section #%zu header for %s",
 				    sec_idx, filename);
-			return err;
+			return -EINVAL;
 		}
 
 		sec_name = elf_strptr(obj->elf, obj->shstrs_sec_idx, shdr->sh_name);
 		if (!sec_name) {
-			err = -errno;
 			pr_warn_elf("failed to get section #%zu name for %s",
 				    sec_idx, filename);
-			return err;
+			return -EINVAL;
 		}
 
 		data = elf_getdata(scn, 0);
 		if (!data) {
-			err = -errno;
 			pr_warn_elf("failed to get section #%zu (%s) data from %s",
 				    sec_idx, sec_name, filename);
-			return err;
+			return -EINVAL;
 		}
 
 		sec = add_src_sec(obj, sec_name);
@@ -1969,7 +1966,7 @@
 
 	obj->sym_map[src_sym_idx] = dst_sym_idx;
 
-	if (sym_type == STT_SECTION && dst_sym) {
+	if (sym_type == STT_SECTION && dst_sec) {
 		dst_sec->sec_sym_idx = dst_sym_idx;
 		dst_sym->st_value = 0;
 	}
@@ -2000,7 +1997,7 @@
 static int linker_append_elf_relos(struct bpf_linker *linker, struct src_obj *obj)
 {
 	struct src_sec *src_symtab = &obj->secs[obj->symtab_sec_idx];
-	struct dst_sec *dst_symtab = &linker->secs[linker->symtab_sec_idx];
+	struct dst_sec *dst_symtab;
 	int i, err;
 
 	for (i = 1; i < obj->sec_cnt; i++) {
@@ -2033,6 +2030,9 @@
 			return -1;
 		}
 
+		/* add_dst_sec() above could have invalidated linker->secs */
+		dst_symtab = &linker->secs[linker->symtab_sec_idx];
+
 		/* shdr->sh_link points to SYMTAB */
 		dst_sec->shdr->sh_link = linker->symtab_sec_idx;
 
@@ -2189,10 +2189,17 @@
 		vi = btf_var_secinfos(t);
 		for (j = 0, m = btf_vlen(t); j < m; j++, vi++) {
 			const struct btf_type *vt = btf__type_by_id(obj->btf, vi->type);
-			const char *var_name = btf__str_by_offset(obj->btf, vt->name_off);
-			int var_linkage = btf_var(vt)->linkage;
+			const char *var_name;
+			int var_linkage;
 			Elf64_Sym *sym;
 
+			/* could be a variable or function */
+			if (!btf_is_var(vt))
+				continue;
+
+			var_name = btf__str_by_offset(obj->btf, vt->name_off);
+			var_linkage = btf_var(vt)->linkage;
+
 			/* no need to patch up static or extern vars */
 			if (var_linkage != BTF_VAR_GLOBAL_ALLOCATED)
 				continue;
@@ -2588,14 +2595,14 @@
 
 	/* Finalize ELF layout */
 	if (elf_update(linker->elf, ELF_C_NULL) < 0) {
-		err = -errno;
+		err = -EINVAL;
 		pr_warn_elf("failed to finalize ELF layout");
 		return libbpf_err(err);
 	}
 
 	/* Write out final ELF contents */
 	if (elf_update(linker->elf, ELF_C_WRITE) < 0) {
-		err = -errno;
+		err = -EINVAL;
 		pr_warn_elf("failed to write ELF contents");
 		return libbpf_err(err);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/netlink.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/netlink.c
@@ -87,29 +87,75 @@
 	NL_DONE,
 };
 
+static int netlink_recvmsg(int sock, struct msghdr *mhdr, int flags)
+{
+	int len;
+
+	do {
+		len = recvmsg(sock, mhdr, flags);
+	} while (len < 0 && (errno == EINTR || errno == EAGAIN));
+
+	if (len < 0)
+		return -errno;
+	return len;
+}
+
+static int alloc_iov(struct iovec *iov, int len)
+{
+	void *nbuf;
+
+	nbuf = realloc(iov->iov_base, len);
+	if (!nbuf)
+		return -ENOMEM;
+
+	iov->iov_base = nbuf;
+	iov->iov_len = len;
+	return 0;
+}
+
 static int libbpf_netlink_recv(int sock, __u32 nl_pid, int seq,
 			       __dump_nlmsg_t _fn, libbpf_dump_nlmsg_t fn,
 			       void *cookie)
 {
+	struct iovec iov = {};
+	struct msghdr mhdr = {
+		.msg_iov = &iov,
+		.msg_iovlen = 1,
+	};
 	bool multipart = true;
 	struct nlmsgerr *err;
 	struct nlmsghdr *nh;
-	char buf[4096];
 	int len, ret;
 
+	ret = alloc_iov(&iov, 4096);
+	if (ret)
+		goto done;
+
 	while (multipart) {
 start:
 		multipart = false;
-		len = recv(sock, buf, sizeof(buf), 0);
+		len = netlink_recvmsg(sock, &mhdr, MSG_PEEK | MSG_TRUNC);
 		if (len < 0) {
-			ret = -errno;
+			ret = len;
+			goto done;
+		}
+
+		if (len > iov.iov_len) {
+			ret = alloc_iov(&iov, len);
+			if (ret)
+				goto done;
+		}
+
+		len = netlink_recvmsg(sock, &mhdr, 0);
+		if (len < 0) {
+			ret = len;
 			goto done;
 		}
 
 		if (len == 0)
 			break;
 
-		for (nh = (struct nlmsghdr *)buf; NLMSG_OK(nh, len);
+		for (nh = (struct nlmsghdr *)iov.iov_base; NLMSG_OK(nh, len);
 		     nh = NLMSG_NEXT(nh, len)) {
 			if (nh->nlmsg_pid != nl_pid) {
 				ret = -LIBBPF_ERRNO__WRNGPID;
@@ -130,7 +176,8 @@
 				libbpf_nla_dump_errormsg(nh);
 				goto done;
 			case NLMSG_DONE:
-				return 0;
+				ret = 0;
+				goto done;
 			default:
 				break;
 			}
@@ -142,15 +189,17 @@
 				case NL_NEXT:
 					goto start;
 				case NL_DONE:
-					return 0;
+					ret = 0;
+					goto done;
 				default:
-					return ret;
+					goto done;
 				}
 			}
 		}
 	}
 	ret = 0;
 done:
+	free(iov.iov_base);
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/nlattr.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/nlattr.c
@@ -178,7 +178,7 @@
 		hlen += nlmsg_len(&err->msg);
 
 	attr = (struct nlattr *) ((void *) err + hlen);
-	alen = nlh->nlmsg_len - hlen;
+	alen = (void *)nlh + nlh->nlmsg_len - (void *)attr;
 
 	if (libbpf_nla_parse(tb, NLMSGERR_ATTR_MAX, attr, alen,
 			     extack_policy) != 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/ringbuf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/ringbuf.c
@@ -59,6 +59,7 @@
 	__u32 len = sizeof(info);
 	struct epoll_event *e;
 	struct ring *r;
+	__u64 mmap_sz;
 	void *tmp;
 	int err;
 
@@ -97,8 +98,7 @@
 	r->mask = info.max_entries - 1;
 
 	/* Map writable consumer page */
-	tmp = mmap(NULL, rb->page_size, PROT_READ | PROT_WRITE, MAP_SHARED,
-		   map_fd, 0);
+	tmp = mmap(NULL, rb->page_size, PROT_READ | PROT_WRITE, MAP_SHARED, map_fd, 0);
 	if (tmp == MAP_FAILED) {
 		err = -errno;
 		pr_warn("ringbuf: failed to mmap consumer page for map fd=%d: %d\n",
@@ -111,8 +111,12 @@
 	 * data size to allow simple reading of samples that wrap around the
 	 * end of a ring buffer. See kernel implementation for details.
 	 * */
-	tmp = mmap(NULL, rb->page_size + 2 * info.max_entries, PROT_READ,
-		   MAP_SHARED, map_fd, rb->page_size);
+	mmap_sz = rb->page_size + 2 * (__u64)info.max_entries;
+	if (mmap_sz != (__u64)(size_t)mmap_sz) {
+		pr_warn("ringbuf: ring buffer size (%u) is too big\n", info.max_entries);
+		return libbpf_err(-E2BIG);
+	}
+	tmp = mmap(NULL, (size_t)mmap_sz, PROT_READ, MAP_SHARED, map_fd, rb->page_size);
 	if (tmp == MAP_FAILED) {
 		err = -errno;
 		ringbuf_unmap_ring(rb, r);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/skel_internal.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/skel_internal.h
@@ -105,10 +105,12 @@
 	err = skel_sys_bpf(BPF_PROG_RUN, &attr, sizeof(attr));
 	if (err < 0 || (int)attr.test.retval < 0) {
 		opts->errstr = "failed to execute loader prog";
-		if (err < 0)
+		if (err < 0) {
 			err = -errno;
-		else
+		} else {
 			err = (int)attr.test.retval;
+			errno = -err;
+		}
 		goto out;
 	}
 	err = 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/bpf/xsk.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/bpf/xsk.c
@@ -1164,8 +1164,6 @@
 		goto out_mmap_tx;
 	}
 
-	ctx->prog_fd = -1;
-
 	if (!(xsk->config.libbpf_flags & XSK_LIBBPF_FLAGS__INHIBIT_PROG_LOAD)) {
 		err = __xsk_setup_xdp_prog(xsk, NULL);
 		if (err)
@@ -1210,12 +1208,23 @@
 
 int xsk_umem__delete(struct xsk_umem *umem)
 {
+	struct xdp_mmap_offsets off;
+	int err;
+
 	if (!umem)
 		return 0;
 
 	if (umem->refcount)
 		return -EBUSY;
 
+	err = xsk_get_mmap_offsets(umem->fd, &off);
+	if (!err && umem->fill_save && umem->comp_save) {
+		munmap(umem->fill_save->ring - off.fr.desc,
+		       off.fr.desc + umem->config.fill_size * sizeof(__u64));
+		munmap(umem->comp_save->ring - off.cr.desc,
+		       off.cr.desc + umem->config.comp_size * sizeof(__u64));
+	}
+
 	close(umem->fd);
 	free(umem);
 
@@ -1235,13 +1244,16 @@
 
 	ctx = xsk->ctx;
 	umem = ctx->umem;
-	if (ctx->prog_fd != -1) {
+
+	if (ctx->refcount == 1) {
 		xsk_delete_bpf_maps(xsk);
 		close(ctx->prog_fd);
 		if (ctx->has_bpf_link)
 			close(ctx->link_fd);
 	}
 
+	xsk_put_ctx(ctx, true);
+
 	err = xsk_get_mmap_offsets(xsk->fd, &off);
 	if (!err) {
 		if (xsk->rx) {
@@ -1254,8 +1266,6 @@
 		}
 	}
 
-	xsk_put_ctx(ctx, true);
-
 	umem->refcount--;
 	/* Do not close an fd that also has an associated umem connected
 	 * to it.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/perf/evlist.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/perf/evlist.c
@@ -224,10 +224,10 @@
 
 static void perf_evlist__id_hash(struct perf_evlist *evlist,
 				 struct perf_evsel *evsel,
-				 int cpu, int thread, u64 id)
+				 int cpu_map_idx, int thread, u64 id)
 {
 	int hash;
-	struct perf_sample_id *sid = SID(evsel, cpu, thread);
+	struct perf_sample_id *sid = SID(evsel, cpu_map_idx, thread);
 
 	sid->id = id;
 	sid->evsel = evsel;
@@ -245,21 +245,27 @@
 
 void perf_evlist__id_add(struct perf_evlist *evlist,
 			 struct perf_evsel *evsel,
-			 int cpu, int thread, u64 id)
+			 int cpu_map_idx, int thread, u64 id)
 {
-	perf_evlist__id_hash(evlist, evsel, cpu, thread, id);
+	if (!SID(evsel, cpu_map_idx, thread))
+		return;
+
+	perf_evlist__id_hash(evlist, evsel, cpu_map_idx, thread, id);
 	evsel->id[evsel->ids++] = id;
 }
 
 int perf_evlist__id_add_fd(struct perf_evlist *evlist,
 			   struct perf_evsel *evsel,
-			   int cpu, int thread, int fd)
+			   int cpu_map_idx, int thread, int fd)
 {
 	u64 read_data[4] = { 0, };
 	int id_idx = 1; /* The first entry is the counter value */
 	u64 id;
 	int ret;
 
+	if (!SID(evsel, cpu_map_idx, thread))
+		return -1;
+
 	ret = ioctl(fd, PERF_EVENT_IOC_ID, &id);
 	if (!ret)
 		goto add;
@@ -288,7 +294,7 @@
 	id = read_data[id_idx];
 
 add:
-	perf_evlist__id_add(evlist, evsel, cpu, thread, id);
+	perf_evlist__id_add(evlist, evsel, cpu_map_idx, thread, id);
 	return 0;
 }
 
@@ -577,7 +583,6 @@
 {
 	struct perf_evsel *evsel;
 	const struct perf_cpu_map *cpus = evlist->cpus;
-	const struct perf_thread_map *threads = evlist->threads;
 
 	if (!ops || !ops->get || !ops->mmap)
 		return -EINVAL;
@@ -589,7 +594,7 @@
 	perf_evlist__for_each_entry(evlist, evsel) {
 		if ((evsel->attr.read_format & PERF_FORMAT_ID) &&
 		    evsel->sample_id == NULL &&
-		    perf_evsel__alloc_id(evsel, perf_cpu_map__nr(cpus), threads->nr) < 0)
+		    perf_evsel__alloc_id(evsel, evsel->fd->max_x, evsel->fd->max_y) < 0)
 			return -ENOMEM;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/perf/include/internal/evlist.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/perf/include/internal/evlist.h
@@ -119,11 +119,11 @@
 
 void perf_evlist__id_add(struct perf_evlist *evlist,
 			 struct perf_evsel *evsel,
-			 int cpu, int thread, u64 id);
+			 int cpu_map_idx, int thread, u64 id);
 
 int perf_evlist__id_add_fd(struct perf_evlist *evlist,
 			   struct perf_evsel *evsel,
-			   int cpu, int thread, int fd);
+			   int cpu_map_idx, int thread, int fd);
 
 void perf_evlist__reset_id_hash(struct perf_evlist *evlist);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/subcmd/help.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/subcmd/help.c
@@ -50,11 +50,21 @@
 	if (!cmds->cnt)
 		return;
 
-	for (i = j = 1; i < cmds->cnt; i++)
-		if (strcmp(cmds->names[i]->name, cmds->names[i-1]->name))
-			cmds->names[j++] = cmds->names[i];
-
+	for (i = 1; i < cmds->cnt; i++) {
+		if (!strcmp(cmds->names[i]->name, cmds->names[i-1]->name))
+			zfree(&cmds->names[i - 1]);
+	}
+	for (i = 0, j = 0; i < cmds->cnt; i++) {
+		if (cmds->names[i]) {
+			if (i == j)
+				j++;
+			else
+				cmds->names[j++] = cmds->names[i];
+		}
+	}
 	cmds->cnt = j;
+	while (j < i)
+		cmds->names[j++] = NULL;
 }
 
 void exclude_cmds(struct cmdnames *cmds, struct cmdnames *excludes)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/subcmd/parse-options.c
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/subcmd/parse-options.c
@@ -633,11 +633,10 @@
 			const char *const subcommands[], const char *usagestr[], int flags)
 {
 	struct parse_opt_ctx_t ctx;
+	char *buf = NULL;
 
 	/* build usage string if it's not provided */
 	if (subcommands && !usagestr[0]) {
-		char *buf = NULL;
-
 		astrcatf(&buf, "%s %s [<options>] {", subcmd_config.exec_name, argv[0]);
 
 		for (int i = 0; subcommands[i]; i++) {
@@ -679,7 +678,10 @@
 			astrcatf(&error_buf, "unknown switch `%c'", *ctx.opt);
 		usage_with_options(usagestr, options);
 	}
-
+	if (buf) {
+		usagestr[0] = NULL;
+		free(buf);
+	}
 	return parse_options_end(&ctx);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/lib/subcmd/subcmd-util.h
+++ linux-xilinx-zynqmp-5.15.0/tools/lib/subcmd/subcmd-util.h
@@ -50,15 +50,8 @@
 static inline void *xrealloc(void *ptr, size_t size)
 {
 	void *ret = realloc(ptr, size);
-	if (!ret && !size)
-		ret = realloc(ptr, 1);
-	if (!ret) {
-		ret = realloc(ptr, size);
-		if (!ret && !size)
-			ret = realloc(ptr, 1);
-		if (!ret)
-			die("Out of memory, realloc failed");
-	}
+	if (!ret)
+		die("Out of memory, realloc failed");
 	return ret;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/memory-model/lock.cat
+++ linux-xilinx-zynqmp-5.15.0/tools/memory-model/lock.cat
@@ -102,19 +102,19 @@
  * within one of the lock's critical sections returns False.
  *)
 
-(* rfi for RU events: an RU may read from the last po-previous UL *)
-let rfi-ru = ([UL] ; po-loc ; [RU]) \ ([UL] ; po-loc ; [LKW] ; po-loc)
-
-(* rfe for RU events: an RU may read from an external UL or the initial write *)
-let all-possible-rfe-ru =
-	let possible-rfe-ru r =
+(*
+ * rf for RU events: an RU may read from an external UL or the initial write,
+ * or from the last po-previous UL
+ *)
+let all-possible-rf-ru =
+	let possible-rf-ru r =
 		let pair-to-relation p = p ++ 0
-		in map pair-to-relation (((UL | IW) * {r}) & loc & ext)
-	in map possible-rfe-ru RU
+		in map pair-to-relation ((((UL | IW) * {r}) & loc & ext) |
+			(((UL * {r}) & po-loc) \ ([UL] ; po-loc ; [LKW] ; po-loc)))
+	in map possible-rf-ru RU
 
 (* Generate all rf relations for RU events *)
-with rfe-ru from cross(all-possible-rfe-ru)
-let rf-ru = rfe-ru | rfi-ru
+with rf-ru from cross(all-possible-rf-ru)
 
 (* Final rf relation *)
 let rf = rf | rf-lf | rf-ru
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/Makefile
@@ -19,8 +19,8 @@
 OBJTOOL    := $(OUTPUT)objtool
 OBJTOOL_IN := $(OBJTOOL)-in.o
 
-LIBELF_FLAGS := $(shell pkg-config libelf --cflags 2>/dev/null)
-LIBELF_LIBS  := $(shell pkg-config libelf --libs 2>/dev/null || echo -lelf)
+LIBELF_FLAGS := $(shell $(HOSTPKG_CONFIG) libelf --cflags 2>/dev/null)
+LIBELF_LIBS  := $(shell $(HOSTPKG_CONFIG) libelf --libs 2>/dev/null || echo -lelf)
 
 all: $(OBJTOOL)
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/arch/x86/decode.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/arch/x86/decode.c
@@ -529,6 +529,11 @@
 		}
 		break;
 
+	case 0xcc:
+		/* int3 */
+		*type = INSN_TRAP;
+		break;
+
 	case 0xe3:
 		/* jecxz/jrcxz */
 		*type = INSN_JUMP_CONDITIONAL;
@@ -659,154 +664,52 @@
 	return nops[len-1];
 }
 
-/* asm/alternative.h ? */
-
-#define ALTINSTR_FLAG_INV	(1 << 15)
-#define ALT_NOT(feat)		((feat) | ALTINSTR_FLAG_INV)
+#define BYTE_RET	0xC3
 
-struct alt_instr {
-	s32 instr_offset;	/* original instruction */
-	s32 repl_offset;	/* offset to replacement instruction */
-	u16 cpuid;		/* cpuid bit set for replacement */
-	u8  instrlen;		/* length of original instruction */
-	u8  replacementlen;	/* length of new instruction */
-} __packed;
-
-static int elf_add_alternative(struct elf *elf,
-			       struct instruction *orig, struct symbol *sym,
-			       int cpuid, u8 orig_len, u8 repl_len)
+const char *arch_ret_insn(int len)
 {
-	const int size = sizeof(struct alt_instr);
-	struct alt_instr *alt;
-	struct section *sec;
-	Elf_Scn *s;
-
-	sec = find_section_by_name(elf, ".altinstructions");
-	if (!sec) {
-		sec = elf_create_section(elf, ".altinstructions",
-					 SHF_ALLOC, 0, 0);
-
-		if (!sec) {
-			WARN_ELF("elf_create_section");
-			return -1;
-		}
-	}
-
-	s = elf_getscn(elf->elf, sec->idx);
-	if (!s) {
-		WARN_ELF("elf_getscn");
-		return -1;
-	}
-
-	sec->data = elf_newdata(s);
-	if (!sec->data) {
-		WARN_ELF("elf_newdata");
-		return -1;
-	}
-
-	sec->data->d_size = size;
-	sec->data->d_align = 1;
-
-	alt = sec->data->d_buf = malloc(size);
-	if (!sec->data->d_buf) {
-		perror("malloc");
-		return -1;
-	}
-	memset(sec->data->d_buf, 0, size);
-
-	if (elf_add_reloc_to_insn(elf, sec, sec->sh.sh_size,
-				  R_X86_64_PC32, orig->sec, orig->offset)) {
-		WARN("elf_create_reloc: alt_instr::instr_offset");
-		return -1;
-	}
-
-	if (elf_add_reloc(elf, sec, sec->sh.sh_size + 4,
-			  R_X86_64_PC32, sym, 0)) {
-		WARN("elf_create_reloc: alt_instr::repl_offset");
-		return -1;
-	}
-
-	alt->cpuid = bswap_if_needed(cpuid);
-	alt->instrlen = orig_len;
-	alt->replacementlen = repl_len;
-
-	sec->sh.sh_size += size;
-	sec->changed = true;
-
-	return 0;
-}
-
-#define X86_FEATURE_RETPOLINE                ( 7*32+12)
-
-int arch_rewrite_retpolines(struct objtool_file *file)
-{
-	struct instruction *insn;
-	struct reloc *reloc;
-	struct symbol *sym;
-	char name[32] = "";
-
-	list_for_each_entry(insn, &file->retpoline_call_list, call_node) {
-
-		if (insn->type != INSN_JUMP_DYNAMIC &&
-		    insn->type != INSN_CALL_DYNAMIC)
-			continue;
-
-		if (!strcmp(insn->sec->name, ".text.__x86.indirect_thunk"))
-			continue;
-
-		reloc = insn->reloc;
-
-		sprintf(name, "__x86_indirect_alt_%s_%s",
-			insn->type == INSN_JUMP_DYNAMIC ? "jmp" : "call",
-			reloc->sym->name + 21);
-
-		sym = find_symbol_by_name(file->elf, name);
-		if (!sym) {
-			sym = elf_create_undef_symbol(file->elf, name);
-			if (!sym) {
-				WARN("elf_create_undef_symbol");
-				return -1;
-			}
-		}
+	static const char ret[5][5] = {
+		{ BYTE_RET },
+		{ BYTE_RET, 0xcc },
+		{ BYTE_RET, 0xcc, BYTES_NOP1 },
+		{ BYTE_RET, 0xcc, BYTES_NOP2 },
+		{ BYTE_RET, 0xcc, BYTES_NOP3 },
+	};
 
-		if (elf_add_alternative(file->elf, insn, sym,
-					ALT_NOT(X86_FEATURE_RETPOLINE), 5, 5)) {
-			WARN("elf_add_alternative");
-			return -1;
-		}
+	if (len < 1 || len > 5) {
+		WARN("invalid RET size: %d\n", len);
+		return NULL;
 	}
 
-	return 0;
+	return ret[len-1];
 }
 
-int arch_decode_hint_reg(struct instruction *insn, u8 sp_reg)
+int arch_decode_hint_reg(u8 sp_reg, int *base)
 {
-	struct cfi_reg *cfa = &insn->cfi.cfa;
-
 	switch (sp_reg) {
 	case ORC_REG_UNDEFINED:
-		cfa->base = CFI_UNDEFINED;
+		*base = CFI_UNDEFINED;
 		break;
 	case ORC_REG_SP:
-		cfa->base = CFI_SP;
+		*base = CFI_SP;
 		break;
 	case ORC_REG_BP:
-		cfa->base = CFI_BP;
+		*base = CFI_BP;
 		break;
 	case ORC_REG_SP_INDIRECT:
-		cfa->base = CFI_SP_INDIRECT;
+		*base = CFI_SP_INDIRECT;
 		break;
 	case ORC_REG_R10:
-		cfa->base = CFI_R10;
+		*base = CFI_R10;
 		break;
 	case ORC_REG_R13:
-		cfa->base = CFI_R13;
+		*base = CFI_R13;
 		break;
 	case ORC_REG_DI:
-		cfa->base = CFI_DI;
+		*base = CFI_DI;
 		break;
 	case ORC_REG_DX:
-		cfa->base = CFI_DX;
+		*base = CFI_DX;
 		break;
 	default:
 		return -1;
@@ -819,3 +722,14 @@
 {
 	return !strncmp(sym->name, "__x86_indirect_", 15);
 }
+
+bool arch_is_rethunk(struct symbol *sym)
+{
+	return !strcmp(sym->name, "__x86_return_thunk");
+}
+
+bool arch_is_embedded_insn(struct symbol *sym)
+{
+	return !strcmp(sym->name, "retbleed_return_thunk") ||
+	       !strcmp(sym->name, "srso_safe_ret");
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/builtin-check.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/builtin-check.c
@@ -20,7 +20,7 @@
 #include <objtool/objtool.h>
 
 bool no_fp, no_unreachable, retpoline, module, backtrace, uaccess, stats,
-     validate_dup, vmlinux, mcount, noinstr, backup;
+     validate_dup, vmlinux, mcount, noinstr, backup, sls, unret, rethunk;
 
 static const char * const check_usage[] = {
 	"objtool check [<options>] file.o",
@@ -36,6 +36,8 @@
 	OPT_BOOLEAN('f', "no-fp", &no_fp, "Skip frame pointer validation"),
 	OPT_BOOLEAN('u', "no-unreachable", &no_unreachable, "Skip 'unreachable instruction' warnings"),
 	OPT_BOOLEAN('r', "retpoline", &retpoline, "Validate retpoline assumptions"),
+	OPT_BOOLEAN(0,   "rethunk", &rethunk, "validate and annotate rethunk usage"),
+	OPT_BOOLEAN(0,   "unret", &unret, "validate entry unret placement"),
 	OPT_BOOLEAN('m', "module", &module, "Indicates the object will be part of a kernel module"),
 	OPT_BOOLEAN('b', "backtrace", &backtrace, "unwind on error"),
 	OPT_BOOLEAN('a', "uaccess", &uaccess, "enable uaccess checking"),
@@ -45,6 +47,7 @@
 	OPT_BOOLEAN('l', "vmlinux", &vmlinux, "vmlinux.o validation"),
 	OPT_BOOLEAN('M', "mcount", &mcount, "generate __mcount_loc"),
 	OPT_BOOLEAN('B', "backup", &backup, "create .orig files before modification"),
+	OPT_BOOLEAN('S', "sls", &sls, "validate straight-line-speculation"),
 	OPT_END(),
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/check.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/check.c
@@ -5,6 +5,8 @@
 
 #include <string.h>
 #include <stdlib.h>
+#include <inttypes.h>
+#include <sys/mman.h>
 
 #include <arch/elf.h>
 #include <objtool/builtin.h>
@@ -26,7 +28,11 @@
 	bool skip_orig;
 };
 
-struct cfi_init_state initial_func_cfi;
+static unsigned long nr_cfi, nr_cfi_reused, nr_cfi_cache;
+
+static struct cfi_init_state initial_func_cfi;
+static struct cfi_state init_cfi;
+static struct cfi_state func_cfi;
 
 struct instruction *find_insn(struct objtool_file *file,
 			      struct section *sec, unsigned long offset)
@@ -163,16 +169,20 @@
 		"panic",
 		"do_exit",
 		"do_task_dead",
-		"__module_put_and_exit",
+		"kthread_exit",
+		"make_task_dead",
+		"__module_put_and_kthread_exit",
 		"complete_and_exit",
 		"__reiserfs_panic",
 		"lbug_with_loc",
 		"fortify_panic",
 		"usercopy_abort",
 		"machine_real_restart",
-		"rewind_stack_do_exit",
+		"rewind_stack_and_make_dead",
 		"kunit_try_catch_throw",
 		"xen_start_kernel",
+		"cpu_bringup_and_idle",
+		"stop_this_cpu",
 	};
 
 	if (!func)
@@ -190,7 +200,7 @@
 		return false;
 
 	insn = find_insn(file, func->sec, func->offset);
-	if (!insn->func)
+	if (!insn || !insn->func)
 		return false;
 
 	func_for_each_insn(file, func, insn) {
@@ -265,6 +275,78 @@
 		state->noinstr = sec->noinstr;
 }
 
+static struct cfi_state *cfi_alloc(void)
+{
+	struct cfi_state *cfi = calloc(sizeof(struct cfi_state), 1);
+	if (!cfi) {
+		WARN("calloc failed");
+		exit(1);
+	}
+	nr_cfi++;
+	return cfi;
+}
+
+static int cfi_bits;
+static struct hlist_head *cfi_hash;
+
+static inline bool cficmp(struct cfi_state *cfi1, struct cfi_state *cfi2)
+{
+	return memcmp((void *)cfi1 + sizeof(cfi1->hash),
+		      (void *)cfi2 + sizeof(cfi2->hash),
+		      sizeof(struct cfi_state) - sizeof(struct hlist_node));
+}
+
+static inline u32 cfi_key(struct cfi_state *cfi)
+{
+	return jhash((void *)cfi + sizeof(cfi->hash),
+		     sizeof(*cfi) - sizeof(cfi->hash), 0);
+}
+
+static struct cfi_state *cfi_hash_find_or_add(struct cfi_state *cfi)
+{
+	struct hlist_head *head = &cfi_hash[hash_min(cfi_key(cfi), cfi_bits)];
+	struct cfi_state *obj;
+
+	hlist_for_each_entry(obj, head, hash) {
+		if (!cficmp(cfi, obj)) {
+			nr_cfi_cache++;
+			return obj;
+		}
+	}
+
+	obj = cfi_alloc();
+	*obj = *cfi;
+	hlist_add_head(&obj->hash, head);
+
+	return obj;
+}
+
+static void cfi_hash_add(struct cfi_state *cfi)
+{
+	struct hlist_head *head = &cfi_hash[hash_min(cfi_key(cfi), cfi_bits)];
+
+	hlist_add_head(&cfi->hash, head);
+}
+
+static void *cfi_hash_alloc(unsigned long size)
+{
+	cfi_bits = max(10, ilog2(size));
+	cfi_hash = mmap(NULL, sizeof(struct hlist_head) << cfi_bits,
+			PROT_READ|PROT_WRITE,
+			MAP_PRIVATE|MAP_ANON, -1, 0);
+	if (cfi_hash == (void *)-1L) {
+		WARN("mmap fail cfi_hash");
+		cfi_hash = NULL;
+	}  else if (stats) {
+		printf("cfi_bits: %d\n", cfi_bits);
+	}
+
+	return cfi_hash;
+}
+
+static unsigned long nr_insns;
+static unsigned long nr_insns_visited;
+
 /*
  * Call the arch-specific instruction decoder for all the instructions and add
  * them to the global instruction list.
@@ -275,7 +357,6 @@
 	struct symbol *func;
 	unsigned long offset;
 	struct instruction *insn;
-	unsigned long nr_insns = 0;
 	int ret;
 
 	for_each_sec(file, sec) {
@@ -289,7 +370,8 @@
 			sec->text = true;
 
 		if (!strcmp(sec->name, ".noinstr.text") ||
-		    !strcmp(sec->name, ".entry.text"))
+		    !strcmp(sec->name, ".entry.text") ||
+		    !strncmp(sec->name, ".text..__x86.", 13))
 			sec->noinstr = true;
 
 		for (offset = 0; offset < sec->sh.sh_size; offset += insn->len) {
@@ -301,7 +383,6 @@
 			memset(insn, 0, sizeof(*insn));
 			INIT_LIST_HEAD(&insn->alts);
 			INIT_LIST_HEAD(&insn->stack_ops);
-			init_cfi_state(&insn->cfi);
 
 			insn->sec = sec;
 			insn->offset = offset;
@@ -392,12 +473,12 @@
 		else if (reloc->addend == reloc->sym->sec->sh.sh_size) {
 			insn = find_last_insn(file, reloc->sym->sec);
 			if (!insn) {
-				WARN("can't find unreachable insn at %s+0x%x",
+				WARN("can't find unreachable insn at %s+0x%" PRIx64,
 				     reloc->sym->sec->name, reloc->addend);
 				return -1;
 			}
 		} else {
-			WARN("can't find unreachable insn at %s+0x%x",
+			WARN("can't find unreachable insn at %s+0x%" PRIx64,
 			     reloc->sym->sec->name, reloc->addend);
 			return -1;
 		}
@@ -427,12 +508,12 @@
 		else if (reloc->addend == reloc->sym->sec->sh.sh_size) {
 			insn = find_last_insn(file, reloc->sym->sec);
 			if (!insn) {
-				WARN("can't find reachable insn at %s+0x%x",
+				WARN("can't find reachable insn at %s+0x%" PRIx64,
 				     reloc->sym->sec->name, reloc->addend);
 				return -1;
 			}
 		} else {
-			WARN("can't find reachable insn at %s+0x%x",
+			WARN("can't find reachable insn at %s+0x%" PRIx64,
 			     reloc->sym->sec->name, reloc->addend);
 			return -1;
 		}
@@ -493,6 +574,7 @@
 		if (strncmp(key_name, STATIC_CALL_TRAMP_PREFIX_STR,
 			    STATIC_CALL_TRAMP_PREFIX_LEN)) {
 			WARN("static_call: trampoline name malformed: %s", key_name);
+			free(key_name);
 			return -1;
 		}
 		tmp = key_name + STATIC_CALL_TRAMP_PREFIX_LEN - STATIC_CALL_KEY_PREFIX_LEN;
@@ -502,6 +584,7 @@
 		if (!key_sym) {
 			if (!module) {
 				WARN("static_call: can't find static_call_key symbol: %s", tmp);
+				free(key_name);
 				return -1;
 			}
 
@@ -531,6 +614,98 @@
 	return 0;
 }
 
+static int create_retpoline_sites_sections(struct objtool_file *file)
+{
+	struct instruction *insn;
+	struct section *sec;
+	int idx;
+
+	sec = find_section_by_name(file->elf, ".retpoline_sites");
+	if (sec) {
+		WARN("file already has .retpoline_sites, skipping");
+		return 0;
+	}
+
+	idx = 0;
+	list_for_each_entry(insn, &file->retpoline_call_list, call_node)
+		idx++;
+
+	if (!idx)
+		return 0;
+
+	sec = elf_create_section(file->elf, ".retpoline_sites", 0,
+				 sizeof(int), idx);
+	if (!sec) {
+		WARN("elf_create_section: .retpoline_sites");
+		return -1;
+	}
+
+	idx = 0;
+	list_for_each_entry(insn, &file->retpoline_call_list, call_node) {
+
+		int *site = (int *)sec->data->d_buf + idx;
+		*site = 0;
+
+		if (elf_add_reloc_to_insn(file->elf, sec,
+					  idx * sizeof(int),
+					  R_X86_64_PC32,
+					  insn->sec, insn->offset)) {
+			WARN("elf_add_reloc_to_insn: .retpoline_sites");
+			return -1;
+		}
+
+		idx++;
+	}
+
+	return 0;
+}
+
+static int create_return_sites_sections(struct objtool_file *file)
+{
+	struct instruction *insn;
+	struct section *sec;
+	int idx;
+
+	sec = find_section_by_name(file->elf, ".return_sites");
+	if (sec) {
+		WARN("file already has .return_sites, skipping");
+		return 0;
+	}
+
+	idx = 0;
+	list_for_each_entry(insn, &file->return_thunk_list, call_node)
+		idx++;
+
+	if (!idx)
+		return 0;
+
+	sec = elf_create_section(file->elf, ".return_sites", 0,
+				 sizeof(int), idx);
+	if (!sec) {
+		WARN("elf_create_section: .return_sites");
+		return -1;
+	}
+
+	idx = 0;
+	list_for_each_entry(insn, &file->return_thunk_list, call_node) {
+
+		int *site = (int *)sec->data->d_buf + idx;
+		*site = 0;
+
+		if (elf_add_reloc_to_insn(file->elf, sec,
+					  idx * sizeof(int),
+					  R_X86_64_PC32,
+					  insn->sec, insn->offset)) {
+			WARN("elf_add_reloc_to_insn: .return_sites");
+			return -1;
+		}
+
+		idx++;
+	}
+
+	return 0;
+}
+
 static int create_mcount_loc_sections(struct objtool_file *file)
 {
 	struct section *sec;
@@ -549,7 +724,7 @@
 		return 0;
 
 	idx = 0;
-	list_for_each_entry(insn, &file->mcount_loc_list, mcount_loc_node)
+	list_for_each_entry(insn, &file->mcount_loc_list, call_node)
 		idx++;
 
 	sec = elf_create_section(file->elf, "__mcount_loc", 0, sizeof(unsigned long), idx);
@@ -557,7 +732,7 @@
 		return -1;
 
 	idx = 0;
-	list_for_each_entry(insn, &file->mcount_loc_list, mcount_loc_node) {
+	list_for_each_entry(insn, &file->mcount_loc_list, call_node) {
 
 		loc = (unsigned long *)sec->data->d_buf + idx;
 		memset(loc, 0, sizeof(unsigned long));
@@ -676,6 +851,16 @@
 	"__tsan_read_write4",
 	"__tsan_read_write8",
 	"__tsan_read_write16",
+	"__tsan_volatile_read1",
+	"__tsan_volatile_read2",
+	"__tsan_volatile_read4",
+	"__tsan_volatile_read8",
+	"__tsan_volatile_read16",
+	"__tsan_volatile_write1",
+	"__tsan_volatile_write2",
+	"__tsan_volatile_write4",
+	"__tsan_volatile_write8",
+	"__tsan_volatile_write16",
 	"__tsan_atomic8_load",
 	"__tsan_atomic16_load",
 	"__tsan_atomic32_load",
@@ -726,6 +911,8 @@
 	"__tsan_atomic64_compare_exchange_val",
 	"__tsan_atomic_thread_fence",
 	"__tsan_atomic_signal_fence",
+	"__tsan_unaligned_read16",
+	"__tsan_unaligned_write16",
 	/* KCOV */
 	"write_comp_data",
 	"check_kcov_mode",
@@ -804,11 +991,33 @@
 	return 0;
 }
 
+/*
+ * Symbols that replace INSN_CALL_DYNAMIC, every (tail) call to such a symbol
+ * will be added to the .retpoline_sites section.
+ */
 __weak bool arch_is_retpoline(struct symbol *sym)
 {
 	return false;
 }
 
+/*
+ * Symbols that replace INSN_RETURN, every (tail) call to such a symbol
+ * will be added to the .return_sites section.
+ */
+__weak bool arch_is_rethunk(struct symbol *sym)
+{
+	return false;
+}
+
+/*
+ * Symbols that are embedded inside other instructions, because sometimes crazy
+ * code exists. These are mostly ignored for validation purposes.
+ */
+__weak bool arch_is_embedded_insn(struct symbol *sym)
+{
+	return false;
+}
+
 #define NEGATIVE_RELOC	((void *)-1L)
 
 static struct reloc *insn_reloc(struct objtool_file *file, struct instruction *insn)
@@ -828,6 +1037,162 @@
 	return insn->reloc;
 }
 
+static void remove_insn_ops(struct instruction *insn)
+{
+	struct stack_op *op, *tmp;
+
+	list_for_each_entry_safe(op, tmp, &insn->stack_ops, list) {
+		list_del(&op->list);
+		free(op);
+	}
+}
+
+static void annotate_call_site(struct objtool_file *file,
+			       struct instruction *insn, bool sibling)
+{
+	struct reloc *reloc = insn_reloc(file, insn);
+	struct symbol *sym = insn->call_dest;
+
+	if (!sym)
+		sym = reloc->sym;
+
+	/*
+	 * Alternative replacement code is just template code which is
+	 * sometimes copied to the original instruction. For now, don't
+	 * annotate it. (In the future we might consider annotating the
+	 * original instruction if/when it ever makes sense to do so.)
+	 */
+	if (!strcmp(insn->sec->name, ".altinstr_replacement"))
+		return;
+
+	if (sym->static_call_tramp) {
+		list_add_tail(&insn->call_node, &file->static_call_list);
+		return;
+	}
+
+	if (sym->retpoline_thunk) {
+		list_add_tail(&insn->call_node, &file->retpoline_call_list);
+		return;
+	}
+
+	/*
+	 * Many compilers cannot disable KCOV with a function attribute
+	 * so they need a little help, NOP out any KCOV calls from noinstr
+	 * text.
+	 */
+	if (insn->sec->noinstr && sym->kcov) {
+		if (reloc) {
+			reloc->type = R_NONE;
+			elf_write_reloc(file->elf, reloc);
+		}
+
+		elf_write_insn(file->elf, insn->sec,
+			       insn->offset, insn->len,
+			       sibling ? arch_ret_insn(insn->len)
+			               : arch_nop_insn(insn->len));
+
+		insn->type = sibling ? INSN_RETURN : INSN_NOP;
+
+		if (sibling) {
+			/*
+			 * We've replaced the tail-call JMP insn by two new
+			 * insn: RET; INT3, except we only have a single struct
+			 * insn here. Mark it retpoline_safe to avoid the SLS
+			 * warning, instead of adding another insn.
+			 */
+			insn->retpoline_safe = true;
+		}
+
+		return;
+	}
+
+	if (mcount && sym->fentry) {
+		if (sibling)
+			WARN_FUNC("Tail call to __fentry__ !?!?", insn->sec, insn->offset);
+
+		if (reloc) {
+			reloc->type = R_NONE;
+			elf_write_reloc(file->elf, reloc);
+		}
+
+		elf_write_insn(file->elf, insn->sec,
+			       insn->offset, insn->len,
+			       arch_nop_insn(insn->len));
+
+		insn->type = INSN_NOP;
+
+		list_add_tail(&insn->call_node, &file->mcount_loc_list);
+		return;
+	}
+}
+
+static void add_call_dest(struct objtool_file *file, struct instruction *insn,
+			  struct symbol *dest, bool sibling)
+{
+	insn->call_dest = dest;
+	if (!dest)
+		return;
+
+	/*
+	 * Whatever stack impact regular CALLs have, should be undone
+	 * by the RETURN of the called function.
+	 *
+	 * Annotated intra-function calls retain the stack_ops but
+	 * are converted to JUMP, see read_intra_function_calls().
+	 */
+	remove_insn_ops(insn);
+
+	annotate_call_site(file, insn, sibling);
+}
+
+static void add_retpoline_call(struct objtool_file *file, struct instruction *insn)
+{
+	/*
+	 * Retpoline calls/jumps are really dynamic calls/jumps in disguise,
+	 * so convert them accordingly.
+	 */
+	switch (insn->type) {
+	case INSN_CALL:
+		insn->type = INSN_CALL_DYNAMIC;
+		break;
+	case INSN_JUMP_UNCONDITIONAL:
+		insn->type = INSN_JUMP_DYNAMIC;
+		break;
+	case INSN_JUMP_CONDITIONAL:
+		insn->type = INSN_JUMP_DYNAMIC_CONDITIONAL;
+		break;
+	default:
+		return;
+	}
+
+	insn->retpoline_safe = true;
+
+	/*
+	 * Whatever stack impact regular CALLs have, should be undone
+	 * by the RETURN of the called function.
+	 *
+	 * Annotated intra-function calls retain the stack_ops but
+	 * are converted to JUMP, see read_intra_function_calls().
+	 */
+	remove_insn_ops(insn);
+
+	annotate_call_site(file, insn, false);
+}
+
+static void add_return_call(struct objtool_file *file, struct instruction *insn, bool add)
+{
+	/*
+	 * Return thunk tail calls are really just returns in disguise,
+	 * so convert them accordingly.
+	 */
+	insn->type = INSN_RETURN;
+	insn->retpoline_safe = true;
+
+	/* Skip the non-text sections, specially .discard ones */
+	if (add && insn->sec->text)
+		list_add_tail(&insn->call_node, &file->return_thunk_list);
+}
+
 /*
  * Find the destination instructions for all jumps.
  */
@@ -849,28 +1214,15 @@
 		} else if (reloc->sym->type == STT_SECTION) {
 			dest_sec = reloc->sym->sec;
 			dest_off = arch_dest_reloc_offset(reloc->addend);
-		} else if (arch_is_retpoline(reloc->sym)) {
-			/*
-			 * Retpoline jumps are really dynamic jumps in
-			 * disguise, so convert them accordingly.
-			 */
-			if (insn->type == INSN_JUMP_UNCONDITIONAL)
-				insn->type = INSN_JUMP_DYNAMIC;
-			else
-				insn->type = INSN_JUMP_DYNAMIC_CONDITIONAL;
-
-			list_add_tail(&insn->call_node,
-				      &file->retpoline_call_list);
-
-			insn->retpoline_safe = true;
+		} else if (reloc->sym->retpoline_thunk) {
+			add_retpoline_call(file, insn);
+			continue;
+		} else if (reloc->sym->return_thunk) {
+			add_return_call(file, insn, true);
 			continue;
 		} else if (insn->func) {
 			/* internal or external sibling call (with reloc) */
-			insn->call_dest = reloc->sym;
-			if (insn->call_dest->static_call_tramp) {
-				list_add_tail(&insn->call_node,
-					      &file->static_call_list);
-			}
+			add_call_dest(file, insn, reloc->sym, true);
 			continue;
 		} else if (reloc->sym->sec->idx) {
 			dest_sec = reloc->sym->sec;
@@ -883,6 +1235,7 @@
 
 		insn->jump_dest = find_insn(file, dest_sec, dest_off);
 		if (!insn->jump_dest) {
+			struct symbol *sym = find_symbol_by_offset(dest_sec, dest_off);
 
 			/*
 			 * This is a special case where an alt instruction
@@ -892,6 +1245,19 @@
 			if (!strcmp(insn->sec->name, ".altinstr_replacement"))
 				continue;
 
+			/*
+			 * This is a special case for retbleed_untrain_ret().
+			 * It jumps to __x86_return_thunk(), but objtool
+			 * can't find the thunk's starting RET
+			 * instruction, because the RET is also in the
+			 * middle of another instruction.  Objtool only
+			 * knows about the outer instruction.
+			 */
+			if (sym && sym->embedded_insn) {
+				add_return_call(file, insn, false);
+				continue;
+			}
+
 			WARN_FUNC("can't find jump dest instruction at %s+0x%lx",
 				  insn->sec, insn->offset, dest_sec->name,
 				  dest_off);
@@ -926,13 +1292,8 @@
 
 			} else if (insn->jump_dest->func->pfunc != insn->func->pfunc &&
 				   insn->jump_dest->offset == insn->jump_dest->func->offset) {
-
 				/* internal sibling call (without reloc) */
-				insn->call_dest = insn->jump_dest->func;
-				if (insn->call_dest->static_call_tramp) {
-					list_add_tail(&insn->call_node,
-						      &file->static_call_list);
-				}
+				add_call_dest(file, insn, insn->jump_dest->func, true);
 			}
 		}
 	}
@@ -940,16 +1301,6 @@
 	return 0;
 }
 
-static void remove_insn_ops(struct instruction *insn)
-{
-	struct stack_op *op, *tmp;
-
-	list_for_each_entry_safe(op, tmp, &insn->stack_ops, list) {
-		list_del(&op->list);
-		free(op);
-	}
-}
-
 static struct symbol *find_call_destination(struct section *sec, unsigned long offset)
 {
 	struct symbol *call_dest;
@@ -968,6 +1319,7 @@
 {
 	struct instruction *insn;
 	unsigned long dest_off;
+	struct symbol *dest;
 	struct reloc *reloc;
 
 	for_each_insn(file, insn) {
@@ -977,7 +1329,9 @@
 		reloc = insn_reloc(file, insn);
 		if (!reloc) {
 			dest_off = arch_jump_destination(insn);
-			insn->call_dest = find_call_destination(insn->sec, dest_off);
+			dest = find_call_destination(insn->sec, dest_off);
+
+			add_call_dest(file, insn, dest, false);
 
 			if (insn->ignore)
 				continue;
@@ -995,9 +1349,8 @@
 
 		} else if (reloc->sym->type == STT_SECTION) {
 			dest_off = arch_dest_reloc_offset(reloc->addend);
-			insn->call_dest = find_call_destination(reloc->sym->sec,
-								dest_off);
-			if (!insn->call_dest) {
+			dest = find_call_destination(reloc->sym->sec, dest_off);
+			if (!dest) {
 				WARN_FUNC("can't find call dest symbol at %s+0x%lx",
 					  insn->sec, insn->offset,
 					  reloc->sym->sec->name,
@@ -1005,70 +1358,13 @@
 				return -1;
 			}
 
-		} else if (arch_is_retpoline(reloc->sym)) {
-			/*
-			 * Retpoline calls are really dynamic calls in
-			 * disguise, so convert them accordingly.
-			 */
-			insn->type = INSN_CALL_DYNAMIC;
-			insn->retpoline_safe = true;
-
-			list_add_tail(&insn->call_node,
-				      &file->retpoline_call_list);
+			add_call_dest(file, insn, dest, false);
 
-			remove_insn_ops(insn);
-			continue;
+		} else if (reloc->sym->retpoline_thunk) {
+			add_retpoline_call(file, insn);
 
 		} else
-			insn->call_dest = reloc->sym;
-
-		if (insn->call_dest && insn->call_dest->static_call_tramp) {
-			list_add_tail(&insn->call_node,
-				      &file->static_call_list);
-		}
-
-		/*
-		 * Many compilers cannot disable KCOV with a function attribute
-		 * so they need a little help, NOP out any KCOV calls from noinstr
-		 * text.
-		 */
-		if (insn->sec->noinstr &&
-		    !strncmp(insn->call_dest->name, "__sanitizer_cov_", 16)) {
-			if (reloc) {
-				reloc->type = R_NONE;
-				elf_write_reloc(file->elf, reloc);
-			}
-
-			elf_write_insn(file->elf, insn->sec,
-				       insn->offset, insn->len,
-				       arch_nop_insn(insn->len));
-			insn->type = INSN_NOP;
-		}
-
-		if (mcount && !strcmp(insn->call_dest->name, "__fentry__")) {
-			if (reloc) {
-				reloc->type = R_NONE;
-				elf_write_reloc(file->elf, reloc);
-			}
-
-			elf_write_insn(file->elf, insn->sec,
-				       insn->offset, insn->len,
-				       arch_nop_insn(insn->len));
-
-			insn->type = INSN_NOP;
-
-			list_add_tail(&insn->mcount_loc_node,
-				      &file->mcount_loc_list);
-		}
-
-		/*
-		 * Whatever stack impact regular CALLs have, should be undone
-		 * by the RETURN of the called function.
-		 *
-		 * Annotated intra-function calls retain the stack_ops but
-		 * are converted to JUMP, see read_intra_function_calls().
-		 */
-		remove_insn_ops(insn);
+			add_call_dest(file, insn, reloc->sym, false);
 	}
 
 	return 0;
@@ -1136,7 +1432,6 @@
 		memset(nop, 0, sizeof(*nop));
 		INIT_LIST_HEAD(&nop->alts);
 		INIT_LIST_HEAD(&nop->stack_ops);
-		init_cfi_state(&nop->cfi);
 
 		nop->sec = special_alt->new_sec;
 		nop->offset = special_alt->new_off + special_alt->new_len;
@@ -1545,10 +1840,11 @@
 
 static int read_unwind_hints(struct objtool_file *file)
 {
+	struct cfi_state cfi = init_cfi;
 	struct section *sec, *relocsec;
-	struct reloc *reloc;
 	struct unwind_hint *hint;
 	struct instruction *insn;
+	struct reloc *reloc;
 	int i;
 
 	sec = find_section_by_name(file->elf, ".discard.unwind_hints");
@@ -1585,20 +1881,49 @@
 
 		insn->hint = true;
 
+		if (hint->type == UNWIND_HINT_TYPE_SAVE) {
+			insn->hint = false;
+			insn->save = true;
+			continue;
+		}
+
+		if (hint->type == UNWIND_HINT_TYPE_RESTORE) {
+			insn->restore = true;
+			continue;
+		}
+
+		if (hint->type == UNWIND_HINT_TYPE_REGS_PARTIAL) {
+			struct symbol *sym = find_symbol_by_offset(insn->sec, insn->offset);
+
+			if (sym && sym->bind == STB_GLOBAL) {
+				insn->entry = 1;
+			}
+		}
+
+		if (hint->type == UNWIND_HINT_TYPE_ENTRY) {
+			hint->type = UNWIND_HINT_TYPE_CALL;
+			insn->entry = 1;
+		}
+
 		if (hint->type == UNWIND_HINT_TYPE_FUNC) {
-			set_func_state(&insn->cfi);
+			insn->cfi = &func_cfi;
 			continue;
 		}
 
-		if (arch_decode_hint_reg(insn, hint->sp_reg)) {
+		if (insn->cfi)
+			cfi = *(insn->cfi);
+
+		if (arch_decode_hint_reg(hint->sp_reg, &cfi.cfa.base)) {
 			WARN_FUNC("unsupported unwind_hint sp base reg %d",
 				  insn->sec, insn->offset, hint->sp_reg);
 			return -1;
 		}
 
-		insn->cfi.cfa.offset = bswap_if_needed(hint->sp_offset);
-		insn->cfi.type = hint->type;
-		insn->cfi.end = hint->end;
+		cfi.cfa.offset = bswap_if_needed(hint->sp_offset);
+		cfi.type = hint->type;
+		cfi.end = hint->end;
+
+		insn->cfi = cfi_hash_find_or_add(&cfi);
 	}
 
 	return 0;
@@ -1627,8 +1952,10 @@
 		}
 
 		if (insn->type != INSN_JUMP_DYNAMIC &&
-		    insn->type != INSN_CALL_DYNAMIC) {
-			WARN_FUNC("retpoline_safe hint not an indirect jump/call",
+		    insn->type != INSN_CALL_DYNAMIC &&
+		    insn->type != INSN_RETURN &&
+		    insn->type != INSN_NOP) {
+			WARN_FUNC("retpoline_safe hint not an indirect jump/call/ret/nop",
 				  insn->sec, insn->offset);
 			return -1;
 		}
@@ -1737,17 +2064,34 @@
 	return 0;
 }
 
-static int read_static_call_tramps(struct objtool_file *file)
+static int classify_symbols(struct objtool_file *file)
 {
 	struct section *sec;
 	struct symbol *func;
 
 	for_each_sec(file, sec) {
 		list_for_each_entry(func, &sec->symbol_list, list) {
-			if (func->bind == STB_GLOBAL &&
-			    !strncmp(func->name, STATIC_CALL_TRAMP_PREFIX_STR,
+			if (func->bind != STB_GLOBAL)
+				continue;
+
+			if (!strncmp(func->name, STATIC_CALL_TRAMP_PREFIX_STR,
 				     strlen(STATIC_CALL_TRAMP_PREFIX_STR)))
 				func->static_call_tramp = true;
+
+			if (arch_is_retpoline(func))
+				func->retpoline_thunk = true;
+
+			if (arch_is_rethunk(func))
+				func->return_thunk = true;
+
+			if (arch_is_embedded_insn(func))
+				func->embedded_insn = true;
+
+			if (!strcmp(func->name, "__fentry__"))
+				func->fentry = true;
+
+			if (!strncmp(func->name, "__sanitizer_cov_", 16))
+				func->kcov = true;
 		}
 	}
 
@@ -1780,11 +2124,6 @@
 	file->rodata = found;
 }
 
-__weak int arch_rewrite_retpolines(struct objtool_file *file)
-{
-	return 0;
-}
-
 static int decode_sections(struct objtool_file *file)
 {
 	int ret;
@@ -1809,7 +2148,7 @@
 	/*
 	 * Must be before add_{jump_call}_destination.
 	 */
-	ret = read_static_call_tramps(file);
+	ret = classify_symbols(file);
 	if (ret)
 		return ret;
 
@@ -1853,24 +2192,20 @@
 	if (ret)
 		return ret;
 
-	/*
-	 * Must be after add_special_section_alts(), since this will emit
-	 * alternatives. Must be after add_{jump,call}_destination(), since
-	 * those create the call insn lists.
-	 */
-	ret = arch_rewrite_retpolines(file);
-	if (ret)
-		return ret;
-
 	return 0;
 }
 
-static bool is_fentry_call(struct instruction *insn)
+static bool is_special_call(struct instruction *insn)
 {
-	if (insn->type == INSN_CALL && insn->call_dest &&
-	    insn->call_dest->type == STT_NOTYPE &&
-	    !strcmp(insn->call_dest->name, "__fentry__"))
-		return true;
+	if (insn->type == INSN_CALL) {
+		struct symbol *dest = insn->call_dest;
+
+		if (!dest)
+			return false;
+
+		if (dest->fentry || dest->embedded_insn)
+			return true;
+	}
 
 	return false;
 }
@@ -2172,17 +2507,6 @@
 				break;
 			}
 
-			if (!cfi->drap && op->src.reg == CFI_SP &&
-			    op->dest.reg == CFI_BP && cfa->base == CFI_SP &&
-			    check_reg_frame_pos(&regs[CFI_BP], -cfa->offset + op->src.offset)) {
-
-				/* lea disp(%rsp), %rbp */
-				cfa->base = CFI_BP;
-				cfa->offset -= op->src.offset;
-				cfi->bp_scratch = false;
-				break;
-			}
-
 			if (op->src.reg == CFI_SP && cfa->base == CFI_SP) {
 
 				/* drap: lea disp(%rsp), %drap */
@@ -2452,13 +2776,18 @@
 	if (!insn->alt_group)
 		return 0;
 
+	if (!insn->cfi) {
+		WARN("CFI missing");
+		return -1;
+	}
+
 	alt_cfi = insn->alt_group->cfi;
 	group_off = insn->offset - insn->alt_group->first_insn->offset;
 
 	if (!alt_cfi[group_off]) {
-		alt_cfi[group_off] = &insn->cfi;
+		alt_cfi[group_off] = insn->cfi;
 	} else {
-		if (memcmp(alt_cfi[group_off], &insn->cfi, sizeof(struct cfi_state))) {
+		if (cficmp(alt_cfi[group_off], insn->cfi)) {
 			WARN_FUNC("stack layout conflict in alternatives",
 				  insn->sec, insn->offset);
 			return -1;
@@ -2509,9 +2838,14 @@
 
 static bool insn_cfi_match(struct instruction *insn, struct cfi_state *cfi2)
 {
-	struct cfi_state *cfi1 = &insn->cfi;
+	struct cfi_state *cfi1 = insn->cfi;
 	int i;
 
+	if (!cfi1) {
+		WARN("CFI missing");
+		return false;
+	}
+
 	if (memcmp(&cfi1->cfa, &cfi2->cfa, sizeof(cfi1->cfa))) {
 
 		WARN_FUNC("stack state mismatch: cfa1=%d%+d cfa2=%d%+d",
@@ -2696,7 +3030,7 @@
 			   struct instruction *insn, struct insn_state state)
 {
 	struct alternative *alt;
-	struct instruction *next_insn;
+	struct instruction *next_insn, *prev_insn = NULL;
 	struct section *sec;
 	u8 visited;
 	int ret;
@@ -2718,22 +3052,61 @@
 			return 1;
 		}
 
-		visited = 1 << state.uaccess;
-		if (insn->visited) {
+		visited = VISITED_BRANCH << state.uaccess;
+		if (insn->visited & VISITED_BRANCH_MASK) {
 			if (!insn->hint && !insn_cfi_match(insn, &state.cfi))
 				return 1;
 
 			if (insn->visited & visited)
 				return 0;
+		} else {
+			nr_insns_visited++;
 		}
 
 		if (state.noinstr)
 			state.instr += insn->instr;
 
-		if (insn->hint)
-			state.cfi = insn->cfi;
-		else
-			insn->cfi = state.cfi;
+		if (insn->hint) {
+			if (insn->restore) {
+				struct instruction *save_insn, *i;
+
+				i = insn;
+				save_insn = NULL;
+
+				sym_for_each_insn_continue_reverse(file, func, i) {
+					if (i->save) {
+						save_insn = i;
+						break;
+					}
+				}
+
+				if (!save_insn) {
+					WARN_FUNC("no corresponding CFI save for CFI restore",
+						  sec, insn->offset);
+					return 1;
+				}
+
+				if (!save_insn->visited) {
+					WARN_FUNC("objtool isn't smart enough to handle this CFI save/restore combo",
+						  sec, insn->offset);
+					return 1;
+				}
+
+				insn->cfi = save_insn->cfi;
+				nr_cfi_reused++;
+			}
+
+			state.cfi = *insn->cfi;
+		} else {
+			/* XXX track if we actually changed state.cfi */
+
+			if (prev_insn && !cficmp(prev_insn->cfi, &state.cfi)) {
+				insn->cfi = prev_insn->cfi;
+				nr_cfi_reused++;
+			} else {
+				insn->cfi = cfi_hash_find_or_add(&state.cfi);
+			}
+		}
 
 		insn->visited |= visited;
 
@@ -2765,6 +3138,11 @@
 		switch (insn->type) {
 
 		case INSN_RETURN:
+			if (sls && !insn->retpoline_safe &&
+			    next_insn && next_insn->type != INSN_TRAP) {
+				WARN_FUNC("missing int3 after ret",
+					  insn->sec, insn->offset);
+			}
 			return validate_return(func, insn, &state);
 
 		case INSN_CALL:
@@ -2773,7 +3151,7 @@
 			if (ret)
 				return ret;
 
-			if (!no_fp && func && !is_fentry_call(insn) &&
+			if (!no_fp && func && !is_special_call(insn) &&
 			    !has_valid_stack_frame(&state)) {
 				WARN_FUNC("call without frame pointer save/setup",
 					  sec, insn->offset);
@@ -2808,6 +3186,13 @@
 			break;
 
 		case INSN_JUMP_DYNAMIC:
+			if (sls && !insn->retpoline_safe &&
+			    next_insn && next_insn->type != INSN_TRAP) {
+				WARN_FUNC("missing int3 after indirect jump",
+					  insn->sec, insn->offset);
+			}
+
+			/* fallthrough */
 		case INSN_JUMP_DYNAMIC_CONDITIONAL:
 			if (is_sibling_call(insn)) {
 				ret = validate_sibling_call(insn, &state);
@@ -2821,10 +3206,13 @@
 			break;
 
 		case INSN_CONTEXT_SWITCH:
-			if (func && (!next_insn || !next_insn->hint)) {
-				WARN_FUNC("unsupported instruction in callable function",
-					  sec, insn->offset);
-				return 1;
+			if (func) {
+				if (!next_insn || !next_insn->hint) {
+					WARN_FUNC("unsupported instruction in callable function",
+						  sec, insn->offset);
+					return 1;
+				}
+				break;
 			}
 			return 0;
 
@@ -2883,6 +3271,7 @@
 			return 1;
 		}
 
+		prev_insn = insn;
 		insn = next_insn;
 	}
 
@@ -2922,6 +3311,145 @@
 	return warnings;
 }
 
+/*
+ * Validate rethunk entry constraint: must untrain RET before the first RET.
+ *
+ * Follow every branch (intra-function) and ensure ANNOTATE_UNRET_END comes
+ * before an actual RET instruction.
+ */
+static int validate_entry(struct objtool_file *file, struct instruction *insn)
+{
+	struct instruction *next, *dest;
+	int ret, warnings = 0;
+
+	for (;;) {
+		next = next_insn_to_validate(file, insn);
+
+		if (insn->visited & VISITED_ENTRY)
+			return 0;
+
+		insn->visited |= VISITED_ENTRY;
+
+		if (!insn->ignore_alts && !list_empty(&insn->alts)) {
+			struct alternative *alt;
+			bool skip_orig = false;
+
+			list_for_each_entry(alt, &insn->alts, list) {
+				if (alt->skip_orig)
+					skip_orig = true;
+
+				ret = validate_entry(file, alt->insn);
+				if (ret) {
+				        if (backtrace)
+						BT_FUNC("(alt)", insn);
+					return ret;
+				}
+			}
+
+			if (skip_orig)
+				return 0;
+		}
+
+		switch (insn->type) {
+
+		case INSN_CALL_DYNAMIC:
+		case INSN_JUMP_DYNAMIC:
+		case INSN_JUMP_DYNAMIC_CONDITIONAL:
+			WARN_FUNC("early indirect call", insn->sec, insn->offset);
+			return 1;
+
+		case INSN_JUMP_UNCONDITIONAL:
+		case INSN_JUMP_CONDITIONAL:
+			if (!is_sibling_call(insn)) {
+				if (!insn->jump_dest) {
+					WARN_FUNC("unresolved jump target after linking?!?",
+						  insn->sec, insn->offset);
+					return -1;
+				}
+				ret = validate_entry(file, insn->jump_dest);
+				if (ret) {
+					if (backtrace) {
+						BT_FUNC("(branch%s)", insn,
+							insn->type == INSN_JUMP_CONDITIONAL ? "-cond" : "");
+					}
+					return ret;
+				}
+
+				if (insn->type == INSN_JUMP_UNCONDITIONAL)
+					return 0;
+
+				break;
+			}
+
+			/* fallthrough */
+		case INSN_CALL:
+			dest = find_insn(file, insn->call_dest->sec,
+					 insn->call_dest->offset);
+			if (!dest) {
+				WARN("Unresolved function after linking!?: %s",
+				     insn->call_dest->name);
+				return -1;
+			}
+
+			ret = validate_entry(file, dest);
+			if (ret) {
+				if (backtrace)
+					BT_FUNC("(call)", insn);
+				return ret;
+			}
+			/*
+			 * If a call returns without error, it must have seen UNTRAIN_RET.
+			 * Therefore any non-error return is a success.
+			 */
+			return 0;
+
+		case INSN_RETURN:
+			WARN_FUNC("RET before UNTRAIN", insn->sec, insn->offset);
+			return 1;
+
+		case INSN_NOP:
+			if (insn->retpoline_safe)
+				return 0;
+			break;
+
+		default:
+			break;
+		}
+
+		if (!next) {
+			WARN_FUNC("teh end!", insn->sec, insn->offset);
+			return -1;
+		}
+		insn = next;
+	}
+
+	return warnings;
+}
+
+/*
+ * Validate that all branches starting at 'insn->entry' encounter UNRET_END
+ * before RET.
+ */
+static int validate_unret(struct objtool_file *file)
+{
+	struct instruction *insn;
+	int ret, warnings = 0;
+
+	for_each_insn(file, insn) {
+		if (!insn->entry)
+			continue;
+
+		ret = validate_entry(file, insn);
+		if (ret < 0) {
+			WARN_FUNC("Failed UNRET validation", insn->sec, insn->offset);
+			return ret;
+		}
+		warnings += ret;
+	}
+
+	return warnings;
+}
+
 static int validate_retpoline(struct objtool_file *file)
 {
 	struct instruction *insn;
@@ -2929,7 +3457,8 @@
 
 	for_each_insn(file, insn) {
 		if (insn->type != INSN_JUMP_DYNAMIC &&
-		    insn->type != INSN_CALL_DYNAMIC)
+		    insn->type != INSN_CALL_DYNAMIC &&
+		    insn->type != INSN_RETURN)
 			continue;
 
 		if (insn->retpoline_safe)
@@ -2944,9 +3473,17 @@
 		if (!strcmp(insn->sec->name, ".init.text") && !module)
 			continue;
 
-		WARN_FUNC("indirect %s found in RETPOLINE build",
-			  insn->sec, insn->offset,
-			  insn->type == INSN_JUMP_DYNAMIC ? "jump" : "call");
+		if (insn->type == INSN_RETURN) {
+			if (rethunk) {
+				WARN_FUNC("'naked' return found in RETHUNK build",
+					  insn->sec, insn->offset);
+			} else
+				continue;
+		} else {
+			WARN_FUNC("indirect %s found in RETPOLINE build",
+				  insn->sec, insn->offset,
+				  insn->type == INSN_JUMP_DYNAMIC ? "jump" : "call");
+		}
 
 		warnings++;
 	}
@@ -2972,7 +3509,7 @@
 	int i;
 	struct instruction *prev_insn;
 
-	if (insn->ignore || insn->type == INSN_NOP)
+	if (insn->ignore || insn->type == INSN_NOP || insn->type == INSN_TRAP)
 		return true;
 
 	/*
@@ -3138,10 +3675,20 @@
 	int ret, warnings = 0;
 
 	arch_initial_func_cfi_state(&initial_func_cfi);
+	init_cfi_state(&init_cfi);
+	init_cfi_state(&func_cfi);
+	set_func_state(&func_cfi);
+
+	if (!cfi_hash_alloc(1UL << (file->elf->symbol_bits - 3)))
+		goto out;
+
+	cfi_hash_add(&init_cfi);
+	cfi_hash_add(&func_cfi);
 
 	ret = decode_sections(file);
 	if (ret < 0)
 		goto out;
+
 	warnings += ret;
 
 	if (list_empty(&file->insn_list))
@@ -3173,6 +3720,17 @@
 		goto out;
 	warnings += ret;
 
+	if (unret) {
+		/*
+		 * Must be after validate_branch() and friends, it plays
+		 * further games with insn->visited.
+		 */
+		ret = validate_unret(file);
+		if (ret < 0)
+			return ret;
+		warnings += ret;
+	}
+
 	if (!warnings) {
 		ret = validate_reachable_instructions(file);
 		if (ret < 0)
@@ -3185,6 +3743,20 @@
 		goto out;
 	warnings += ret;
 
+	if (retpoline) {
+		ret = create_retpoline_sites_sections(file);
+		if (ret < 0)
+			goto out;
+		warnings += ret;
+	}
+
+	if (rethunk) {
+		ret = create_return_sites_sections(file);
+		if (ret < 0)
+			goto out;
+		warnings += ret;
+	}
+
 	if (mcount) {
 		ret = create_mcount_loc_sections(file);
 		if (ret < 0)
@@ -3192,6 +3764,13 @@
 		warnings += ret;
 	}
 
+	if (stats) {
+		printf("nr_insns_visited: %ld\n", nr_insns_visited);
+		printf("nr_cfi: %ld\n", nr_cfi);
+		printf("nr_cfi_reused: %ld\n", nr_cfi_reused);
+		printf("nr_cfi_cache: %ld\n", nr_cfi_cache);
+	}
+
 out:
 	/*
 	 *  For now, don't fail the kernel build on fatal warnings.  These
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/elf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/elf.c
@@ -314,6 +314,8 @@
 	struct list_head *entry;
 	struct rb_node *pnode;
 
+	sym->alias = sym;
+
 	sym->type = GELF_ST_TYPE(sym->sym.st_info);
 	sym->bind = GELF_ST_BIND(sym->sym.st_info);
 
@@ -375,7 +377,6 @@
 			return -1;
 		}
 		memset(sym, 0, sizeof(*sym));
-		sym->alias = sym;
 
 		sym->idx = i;
 
@@ -485,7 +486,7 @@
 						int reltype);
 
 int elf_add_reloc(struct elf *elf, struct section *sec, unsigned long offset,
-		  unsigned int type, struct symbol *sym, int addend)
+		  unsigned int type, struct symbol *sym, s64 addend)
 {
 	struct reloc *reloc;
 
@@ -514,37 +515,244 @@
 	return 0;
 }
 
+/*
+ * Ensure that any reloc section containing references to @sym is marked
+ * changed such that it will get re-generated in elf_rebuild_reloc_sections()
+ * with the new symbol index.
+ */
+static void elf_dirty_reloc_sym(struct elf *elf, struct symbol *sym)
+{
+	struct section *sec;
+
+	list_for_each_entry(sec, &elf->sections, list) {
+		struct reloc *reloc;
+
+		if (sec->changed)
+			continue;
+
+		list_for_each_entry(reloc, &sec->reloc_list, list) {
+			if (reloc->sym == sym) {
+				sec->changed = true;
+				break;
+			}
+		}
+	}
+}
+
+/*
+ * The libelf API is terrible; gelf_update_sym*() takes a data block relative
+ * index value, *NOT* the symbol index. As such, iterate the data blocks and
+ * adjust index until it fits.
+ *
+ * If no data block is found, allow adding a new data block provided the index
+ * is only one past the end.
+ */
+static int elf_update_symbol(struct elf *elf, struct section *symtab,
+			     struct section *symtab_shndx, struct symbol *sym)
+{
+	Elf32_Word shndx = sym->sec ? sym->sec->idx : SHN_UNDEF;
+	Elf_Data *symtab_data = NULL, *shndx_data = NULL;
+	Elf64_Xword entsize = symtab->sh.sh_entsize;
+	int max_idx, idx = sym->idx;
+	Elf_Scn *s, *t = NULL;
+	bool is_special_shndx = sym->sym.st_shndx >= SHN_LORESERVE &&
+				sym->sym.st_shndx != SHN_XINDEX;
+
+	if (is_special_shndx)
+		shndx = sym->sym.st_shndx;
+
+	s = elf_getscn(elf->elf, symtab->idx);
+	if (!s) {
+		WARN_ELF("elf_getscn");
+		return -1;
+	}
+
+	if (symtab_shndx) {
+		t = elf_getscn(elf->elf, symtab_shndx->idx);
+		if (!t) {
+			WARN_ELF("elf_getscn");
+			return -1;
+		}
+	}
+
+	for (;;) {
+		/* get next data descriptor for the relevant sections */
+		symtab_data = elf_getdata(s, symtab_data);
+		if (t)
+			shndx_data = elf_getdata(t, shndx_data);
+
+		/* end-of-list */
+		if (!symtab_data) {
+			void *buf;
+
+			if (idx) {
+				/* we don't do holes in symbol tables */
+				WARN("index out of range");
+				return -1;
+			}
+
+			/* if @idx == 0, it's the next contiguous entry, create it */
+			symtab_data = elf_newdata(s);
+			if (t)
+				shndx_data = elf_newdata(t);
+
+			buf = calloc(1, entsize);
+			if (!buf) {
+				WARN("malloc");
+				return -1;
+			}
+
+			symtab_data->d_buf = buf;
+			symtab_data->d_size = entsize;
+			symtab_data->d_align = 1;
+			symtab_data->d_type = ELF_T_SYM;
+
+			symtab->sh.sh_size += entsize;
+			symtab->changed = true;
+
+			if (t) {
+				shndx_data->d_buf = &sym->sec->idx;
+				shndx_data->d_size = sizeof(Elf32_Word);
+				shndx_data->d_align = sizeof(Elf32_Word);
+				shndx_data->d_type = ELF_T_WORD;
+
+				symtab_shndx->sh.sh_size += sizeof(Elf32_Word);
+				symtab_shndx->changed = true;
+			}
+
+			break;
+		}
+
+		/* empty blocks should not happen */
+		if (!symtab_data->d_size) {
+			WARN("zero size data");
+			return -1;
+		}
+
+		/* is this the right block? */
+		max_idx = symtab_data->d_size / entsize;
+		if (idx < max_idx)
+			break;
+
+		/* adjust index and try again */
+		idx -= max_idx;
+	}
+
+	/* something went side-ways */
+	if (idx < 0) {
+		WARN("negative index");
+		return -1;
+	}
+
+	/* setup extended section index magic and write the symbol */
+	if ((shndx >= SHN_UNDEF && shndx < SHN_LORESERVE) || is_special_shndx) {
+		sym->sym.st_shndx = shndx;
+		if (!shndx_data)
+			shndx = 0;
+	} else {
+		sym->sym.st_shndx = SHN_XINDEX;
+		if (!shndx_data) {
+			WARN("no .symtab_shndx");
+			return -1;
+		}
+	}
+
+	if (!gelf_update_symshndx(symtab_data, shndx_data, idx, &sym->sym, shndx)) {
+		WARN_ELF("gelf_update_symshndx");
+		return -1;
+	}
+
+	return 0;
+}
+
+static struct symbol *
+elf_create_section_symbol(struct elf *elf, struct section *sec)
+{
+	struct section *symtab, *symtab_shndx;
+	Elf32_Word first_non_local, new_idx;
+	struct symbol *sym, *old;
+
+	symtab = find_section_by_name(elf, ".symtab");
+	if (symtab) {
+		symtab_shndx = find_section_by_name(elf, ".symtab_shndx");
+	} else {
+		WARN("no .symtab");
+		return NULL;
+	}
+
+	sym = calloc(1, sizeof(*sym));
+	if (!sym) {
+		perror("malloc");
+		return NULL;
+	}
+
+	sym->name = sec->name;
+	sym->sec = sec;
+
+	// st_name 0
+	sym->sym.st_info = GELF_ST_INFO(STB_LOCAL, STT_SECTION);
+	// st_other 0
+	// st_value 0
+	// st_size 0
+
+	/*
+	 * Move the first global symbol, as per sh_info, into a new, higher
+	 * symbol index. This fees up a spot for a new local symbol.
+	 */
+	first_non_local = symtab->sh.sh_info;
+	new_idx = symtab->sh.sh_size / symtab->sh.sh_entsize;
+	old = find_symbol_by_index(elf, first_non_local);
+	if (old) {
+		old->idx = new_idx;
+
+		hlist_del(&old->hash);
+		elf_hash_add(symbol, &old->hash, old->idx);
+
+		elf_dirty_reloc_sym(elf, old);
+
+		if (elf_update_symbol(elf, symtab, symtab_shndx, old)) {
+			WARN("elf_update_symbol move");
+			return NULL;
+		}
+
+		new_idx = first_non_local;
+	}
+
+	sym->idx = new_idx;
+	if (elf_update_symbol(elf, symtab, symtab_shndx, sym)) {
+		WARN("elf_update_symbol");
+		return NULL;
+	}
+
+	/*
+	 * Either way, we added a LOCAL symbol.
+	 */
+	symtab->sh.sh_info += 1;
+
+	elf_add_symbol(elf, sym);
+
+	return sym;
+}
+
 int elf_add_reloc_to_insn(struct elf *elf, struct section *sec,
 			  unsigned long offset, unsigned int type,
 			  struct section *insn_sec, unsigned long insn_off)
 {
-	struct symbol *sym;
-	int addend;
-
-	if (insn_sec->sym) {
-		sym = insn_sec->sym;
-		addend = insn_off;
+	struct symbol *sym = insn_sec->sym;
+	int addend = insn_off;
 
-	} else {
+	if (!sym) {
 		/*
-		 * The Clang assembler strips section symbols, so we have to
-		 * reference the function symbol instead:
+		 * Due to how weak functions work, we must use section based
+		 * relocations. Symbol based relocations would result in the
+		 * weak and non-weak function annotations being overlaid on the
+		 * non-weak function after linking.
 		 */
-		sym = find_symbol_containing(insn_sec, insn_off);
-		if (!sym) {
-			/*
-			 * Hack alert.  This happens when we need to reference
-			 * the NOP pad insn immediately after the function.
-			 */
-			sym = find_symbol_containing(insn_sec, insn_off - 1);
-		}
-
-		if (!sym) {
-			WARN("can't find symbol containing %s+0x%lx", insn_sec->name, insn_off);
+		sym = elf_create_section_symbol(elf, insn_sec);
+		if (!sym)
 			return -1;
-		}
 
-		addend = insn_off - sym->offset;
+		insn_sec->sym = sym;
 	}
 
 	return elf_add_reloc(elf, sec, offset, type, sym, addend);
@@ -741,90 +949,6 @@
 	return len;
 }
 
-struct symbol *elf_create_undef_symbol(struct elf *elf, const char *name)
-{
-	struct section *symtab, *symtab_shndx;
-	struct symbol *sym;
-	Elf_Data *data;
-	Elf_Scn *s;
-
-	sym = malloc(sizeof(*sym));
-	if (!sym) {
-		perror("malloc");
-		return NULL;
-	}
-	memset(sym, 0, sizeof(*sym));
-
-	sym->name = strdup(name);
-
-	sym->sym.st_name = elf_add_string(elf, NULL, sym->name);
-	if (sym->sym.st_name == -1)
-		return NULL;
-
-	sym->sym.st_info = GELF_ST_INFO(STB_GLOBAL, STT_NOTYPE);
-	// st_other 0
-	// st_shndx 0
-	// st_value 0
-	// st_size 0
-
-	symtab = find_section_by_name(elf, ".symtab");
-	if (!symtab) {
-		WARN("can't find .symtab");
-		return NULL;
-	}
-
-	s = elf_getscn(elf->elf, symtab->idx);
-	if (!s) {
-		WARN_ELF("elf_getscn");
-		return NULL;
-	}
-
-	data = elf_newdata(s);
-	if (!data) {
-		WARN_ELF("elf_newdata");
-		return NULL;
-	}
-
-	data->d_buf = &sym->sym;
-	data->d_size = sizeof(sym->sym);
-	data->d_align = 1;
-	data->d_type = ELF_T_SYM;
-
-	sym->idx = symtab->sh.sh_size / sizeof(sym->sym);
-
-	symtab->sh.sh_size += data->d_size;
-	symtab->changed = true;
-
-	symtab_shndx = find_section_by_name(elf, ".symtab_shndx");
-	if (symtab_shndx) {
-		s = elf_getscn(elf->elf, symtab_shndx->idx);
-		if (!s) {
-			WARN_ELF("elf_getscn");
-			return NULL;
-		}
-
-		data = elf_newdata(s);
-		if (!data) {
-			WARN_ELF("elf_newdata");
-			return NULL;
-		}
-
-		data->d_buf = &sym->sym.st_size; /* conveniently 0 */
-		data->d_size = sizeof(Elf32_Word);
-		data->d_align = 4;
-		data->d_type = ELF_T_WORD;
-
-		symtab_shndx->sh.sh_size += 4;
-		symtab_shndx->changed = true;
-	}
-
-	sym->sec = find_section_by_index(elf, 0);
-
-	elf_add_symbol(elf, sym);
-
-	return sym;
-}
-
 struct section *elf_create_section(struct elf *elf, const char *name,
 				   unsigned int sh_flags, size_t entsize, int nr)
 {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/include/objtool/arch.h
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/include/objtool/arch.h
@@ -26,6 +26,7 @@
 	INSN_CLAC,
 	INSN_STD,
 	INSN_CLD,
+	INSN_TRAP,
 	INSN_OTHER,
 };
 
@@ -82,10 +83,13 @@
 unsigned long arch_dest_reloc_offset(int addend);
 
 const char *arch_nop_insn(int len);
+const char *arch_ret_insn(int len);
 
-int arch_decode_hint_reg(struct instruction *insn, u8 sp_reg);
+int arch_decode_hint_reg(u8 sp_reg, int *base);
 
 bool arch_is_retpoline(struct symbol *sym);
+bool arch_is_rethunk(struct symbol *sym);
+bool arch_is_embedded_insn(struct symbol *sym);
 
 int arch_rewrite_retpolines(struct objtool_file *file);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/include/objtool/builtin.h
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/include/objtool/builtin.h
@@ -9,7 +9,7 @@
 
 extern const struct option check_options[];
 extern bool no_fp, no_unreachable, retpoline, module, backtrace, uaccess, stats,
-            validate_dup, vmlinux, mcount, noinstr, backup;
+            validate_dup, vmlinux, mcount, noinstr, backup, sls, unret, rethunk;
 
 extern int cmd_parse_options(int argc, const char **argv, const char * const usage[]);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/include/objtool/cfi.h
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/include/objtool/cfi.h
@@ -7,6 +7,7 @@
 #define _OBJTOOL_CFI_H
 
 #include <arch/cfi_regs.h>
+#include <linux/list.h>
 
 #define CFI_UNDEFINED		-1
 #define CFI_CFA			-2
@@ -24,6 +25,7 @@
 };
 
 struct cfi_state {
+	struct hlist_node hash; /* must be first, cficmp() */
 	struct cfi_reg regs[CFI_NUM_REGS];
 	struct cfi_reg vals[CFI_NUM_REGS];
 	struct cfi_reg cfa;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/include/objtool/check.h
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/include/objtool/check.h
@@ -40,7 +40,6 @@
 	struct list_head list;
 	struct hlist_node hash;
 	struct list_head call_node;
-	struct list_head mcount_loc_node;
 	struct section *sec;
 	unsigned long offset;
 	unsigned int len;
@@ -48,7 +47,9 @@
 	unsigned long immediate;
 	bool dead_end, ignore, ignore_alts;
 	bool hint;
+	bool save, restore;
 	bool retpoline_safe;
+	bool entry;
 	s8 instr;
 	u8 visited;
 	struct alt_group *alt_group;
@@ -60,9 +61,14 @@
 	struct list_head alts;
 	struct symbol *func;
 	struct list_head stack_ops;
-	struct cfi_state cfi;
+	struct cfi_state *cfi;
 };
 
+#define VISITED_BRANCH		0x01
+#define VISITED_BRANCH_UACCESS	0x02
+#define VISITED_BRANCH_MASK	0x03
+#define VISITED_ENTRY		0x04
+
 static inline bool is_static_jump(struct instruction *insn)
 {
 	return insn->type == INSN_JUMP_CONDITIONAL ||
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/include/objtool/elf.h
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/include/objtool/elf.h
@@ -54,8 +54,13 @@
 	unsigned long offset;
 	unsigned int len;
 	struct symbol *pfunc, *cfunc, *alias;
-	bool uaccess_safe;
-	bool static_call_tramp;
+	u8 uaccess_safe      : 1;
+	u8 static_call_tramp : 1;
+	u8 retpoline_thunk   : 1;
+	u8 return_thunk      : 1;
+	u8 fentry            : 1;
+	u8 kcov              : 1;
+	u8 embedded_insn     : 1;
 };
 
 struct reloc {
@@ -69,7 +74,7 @@
 	struct symbol *sym;
 	unsigned long offset;
 	unsigned int type;
-	int addend;
+	s64 addend;
 	int idx;
 	bool jump_table_start;
 };
@@ -131,7 +136,7 @@
 struct section *elf_create_section(struct elf *elf, const char *name, unsigned int sh_flags, size_t entsize, int nr);
 
 int elf_add_reloc(struct elf *elf, struct section *sec, unsigned long offset,
-		  unsigned int type, struct symbol *sym, int addend);
+		  unsigned int type, struct symbol *sym, s64 addend);
 int elf_add_reloc_to_insn(struct elf *elf, struct section *sec,
 			  unsigned long offset, unsigned int type,
 			  struct section *insn_sec, unsigned long insn_off);
@@ -140,7 +145,6 @@
 		   unsigned long offset, unsigned int len,
 		   const char *insn);
 int elf_write_reloc(struct elf *elf, struct reloc *reloc);
-struct symbol *elf_create_undef_symbol(struct elf *elf, const char *name);
 int elf_write(struct elf *elf);
 void elf_close(struct elf *elf);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/include/objtool/objtool.h
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/include/objtool/objtool.h
@@ -19,6 +19,7 @@
 	struct list_head insn_list;
 	DECLARE_HASHTABLE(insn_hash, 20);
 	struct list_head retpoline_call_list;
+	struct list_head return_thunk_list;
 	struct list_head static_call_list;
 	struct list_head mcount_loc_list;
 	bool ignore_unreachables, c_file, hints, rodata;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/objtool.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/objtool.c
@@ -126,6 +126,7 @@
 	INIT_LIST_HEAD(&file.insn_list);
 	hash_init(file.insn_hash);
 	INIT_LIST_HEAD(&file.retpoline_call_list);
+	INIT_LIST_HEAD(&file.return_thunk_list);
 	INIT_LIST_HEAD(&file.static_call_list);
 	INIT_LIST_HEAD(&file.mcount_loc_list);
 	file.c_file = !vmlinux && find_section_by_name(file.elf, ".comment");
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/orc_gen.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/orc_gen.c
@@ -13,13 +13,19 @@
 #include <objtool/warn.h>
 #include <objtool/endianness.h>
 
-static int init_orc_entry(struct orc_entry *orc, struct cfi_state *cfi)
+static int init_orc_entry(struct orc_entry *orc, struct cfi_state *cfi,
+			  struct instruction *insn)
 {
-	struct instruction *insn = container_of(cfi, struct instruction, cfi);
 	struct cfi_reg *bp = &cfi->regs[CFI_BP];
 
 	memset(orc, 0, sizeof(*orc));
 
+	if (!cfi) {
+		orc->end = 0;
+		orc->sp_reg = ORC_REG_UNDEFINED;
+		return 0;
+	}
+
 	orc->end = cfi->end;
 
 	if (cfi->cfa.base == CFI_UNDEFINED) {
@@ -162,7 +168,7 @@
 			int i;
 
 			if (!alt_group) {
-				if (init_orc_entry(&orc, &insn->cfi))
+				if (init_orc_entry(&orc, insn->cfi, insn))
 					return -1;
 				if (!memcmp(&prev_orc, &orc, sizeof(orc)))
 					continue;
@@ -186,7 +192,8 @@
 				struct cfi_state *cfi = alt_group->cfi[i];
 				if (!cfi)
 					continue;
-				if (init_orc_entry(&orc, cfi))
+				/* errors are reported on the original insn */
+				if (init_orc_entry(&orc, cfi, insn))
 					return -1;
 				if (!memcmp(&prev_orc, &orc, sizeof(orc)))
 					continue;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/objtool/special.c
+++ linux-xilinx-zynqmp-5.15.0/tools/objtool/special.c
@@ -109,14 +109,6 @@
 			return -1;
 		}
 
-		/*
-		 * Skip retpoline .altinstr_replacement... we already rewrite the
-		 * instructions for retpolines anyway, see arch_is_retpoline()
-		 * usage in add_{call,jump}_destinations().
-		 */
-		if (arch_is_retpoline(new_reloc->sym))
-			return 1;
-
 		reloc_to_sec_off(new_reloc, &alt->new_sec, &alt->new_off);
 
 		/* _ASM_EXTABLE_EX hack */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/Documentation/perf-intel-pt.txt
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/Documentation/perf-intel-pt.txt
@@ -108,9 +108,10 @@
 
 	perf script --itrace=ibxwpe -F+flags
 
-The flags are "bcrosyiABExgh" which stand for branch, call, return, conditional,
+The flags are "bcrosyiABExghDt" which stand for branch, call, return, conditional,
 system, asynchronous, interrupt, transaction abort, trace begin, trace end,
-in transaction, VM-entry, and VM-exit respectively.
+in transaction, VM-entry, VM-exit, interrupt disabled, and interrupt disable
+toggle respectively.
 
 perf script also supports higher level ways to dump instruction traces:
 
@@ -456,6 +457,8 @@
 		which contains "1" if the feature is supported and
 		"0" otherwise.
 
+		As an alternative, refer to "Emulated PTWRITE" further below.
+
 fup_on_ptw	Enable a FUP packet to follow the PTWRITE packet.  The FUP packet
 		provides the address of the ptwrite instruction.  In the absence of
 		fup_on_ptw, the decoder will use the address of the previous branch
@@ -472,6 +475,30 @@
 		which contains "1" if the feature is supported and
 		"0" otherwise.
 
+event		Enable Event Trace.  The events provide information about asynchronous
+		events.
+
+		Support for this feature is indicated by:
+
+			/sys/bus/event_source/devices/intel_pt/caps/event_trace
+
+		which contains "1" if the feature is supported and
+		"0" otherwise.
+
+notnt		Disable TNT packets.  Without TNT packets, it is not possible to walk
+		executable code to reconstruct control flow, however FUP, TIP, TIP.PGE
+		and TIP.PGD packets still indicate asynchronous control flow, and (if
+		return compression is disabled - see noretcomp) return statements.
+		The advantage of eliminating TNT packets is reducing the size of the
+		trace and corresponding tracing overhead.
+
+		Support for this feature is indicated by:
+
+			/sys/bus/event_source/devices/intel_pt/caps/tnt_disable
+
+		which contains "1" if the feature is supported and
+		"0" otherwise.
+
 
 AUX area sampling option
 ~~~~~~~~~~~~~~~~~~~~~~~~
@@ -865,6 +892,8 @@
 	p	synthesize "power" events (incl. PSB events)
 	c	synthesize branches events (calls only)
 	r	synthesize branches events (returns only)
+	o	synthesize PEBS-via-PT events
+	I	synthesize Event Trace events
 	e	synthesize tracing error events
 	d	create a debug log
 	g	synthesize a call chain (use with i or x)
@@ -1338,6 +1367,202 @@
           :17006 17006 [001] 11500.262869216:  ffffffff8220116e error_entry+0xe ([guest.kernel.kallsyms])               pushq  %rax
 
 
+Event Trace
+-----------
+
+Event Trace records information about asynchronous events, for example interrupts,
+faults, VM exits and entries.  The information is recorded in CFE and EVD packets,
+and also the Interrupt Flag is recorded on the MODE.Exec packet.  The CFE packet
+contains a type field to identify one of the following:
+
+	 1	INTR		interrupt, fault, exception, NMI
+	 2	IRET		interrupt return
+	 3	SMI		system management interrupt
+	 4	RSM		resume from system management mode
+	 5	SIPI		startup interprocessor interrupt
+	 6	INIT		INIT signal
+	 7	VMENTRY		VM-Entry
+	 8	VMEXIT		VM-Entry
+	 9	VMEXIT_INTR	VM-Exit due to interrupt
+	10	SHUTDOWN	Shutdown
+
+For more details, refer to the Intel 64 and IA-32 Architectures Software
+Developer Manuals (version 076 or later).
+
+The capability to do Event Trace is indicated by the
+/sys/bus/event_source/devices/intel_pt/caps/event_trace file.
+
+Event trace is selected for recording using the "event" config term. e.g.
+
+	perf record -e intel_pt/event/u uname
+
+Event trace events are output using the --itrace I option. e.g.
+
+	perf script --itrace=Ie
+
+perf script displays events containing CFE type, vector and event data,
+in the form:
+
+	  evt:   hw int            (t)  cfe: INTR IP: 1 vector: 3 PFA: 0x8877665544332211
+
+The IP flag indicates if the event binds to an IP, which includes any case where
+flow control packet generation is enabled, as well as when CFE packet IP bit is
+set.
+
+perf script displays events containing changes to the Interrupt Flag in the form:
+
+	iflag:   t                      IFLAG: 1->0 via branch
+
+where "via branch" indicates a branch (interrupt or return from interrupt) and
+"non branch" indicates an instruction such as CFI, STI or POPF).
+
+In addition, the current state of the interrupt flag is indicated by the presence
+or absence of the "D" (interrupt disabled) perf script flag.  If the interrupt
+flag is changed, then the "t" flag is also included i.e.
+
+		no flag, interrupts enabled IF=1
+	t	interrupts become disabled IF=1 -> IF=0
+	D	interrupts are disabled IF=0
+	Dt	interrupts become enabled  IF=0 -> IF=1
+
+The intel-pt-events.py script illustrates how to access Event Trace information
+using a Python script.
+
+
+TNT Disable
+-----------
+
+TNT packets are disabled using the "notnt" config term. e.g.
+
+	perf record -e intel_pt/notnt/u uname
+
+In that case the --itrace q option is forced because walking executable code
+to reconstruct the control flow is not possible.
+
+
+Emulated PTWRITE
+----------------
+
+Later perf tools support a method to emulate the ptwrite instruction, which
+can be useful if hardware does not support the ptwrite instruction.
+
+Instead of using the ptwrite instruction, a function is used which produces
+a trace that encodes the payload data into TNT packets.  Here is an example
+of the function:
+
+ #include <stdint.h>
+
+ void perf_emulate_ptwrite(uint64_t x)
+ __attribute__((externally_visible, noipa, no_instrument_function, naked));
+
+ #define PERF_EMULATE_PTWRITE_8_BITS \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"        \
+                 "1: shl %rax\n"     \
+                 "   jc 1f\n"
+
+ /* Undefined instruction */
+ #define PERF_EMULATE_PTWRITE_UD2        ".byte 0x0f, 0x0b\n"
+
+ #define PERF_EMULATE_PTWRITE_MAGIC        PERF_EMULATE_PTWRITE_UD2 ".ascii \"perf,ptwrite  \"\n"
+
+ void perf_emulate_ptwrite(uint64_t x __attribute__ ((__unused__)))
+ {
+          /* Assumes SysV ABI : x passed in rdi */
+         __asm__ volatile (
+                 "jmp 1f\n"
+                 PERF_EMULATE_PTWRITE_MAGIC
+                 "1: mov %rdi, %rax\n"
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 PERF_EMULATE_PTWRITE_8_BITS
+                 "1: ret\n"
+         );
+ }
+
+For example, a test program with the function above:
+
+ #include <stdio.h>
+ #include <stdint.h>
+ #include <stdlib.h>
+
+ #include "perf_emulate_ptwrite.h"
+
+ int main(int argc, char *argv[])
+ {
+         uint64_t x = 0;
+
+         if (argc > 1)
+                 x = strtoull(argv[1], NULL, 0);
+         perf_emulate_ptwrite(x);
+         return 0;
+ }
+
+Can be compiled and traced:
+
+ $ gcc -Wall -Wextra -O3 -g -o eg_ptw eg_ptw.c
+ $ perf record -e intel_pt//u ./eg_ptw 0x1234567890abcdef
+ [ perf record: Woken up 1 times to write data ]
+ [ perf record: Captured and wrote 0.017 MB perf.data ]
+ $ perf script --itrace=ew
+           eg_ptw 19875 [007]  8061.235912:     ptwrite:  IP: 0 payload: 0x1234567890abcdef      55701249a196 perf_emulate_ptwrite+0x16 (/home/user/eg_ptw)
+ $
+
+
+Pipe mode
+---------
+Pipe mode is a problem for Intel PT and possibly other auxtrace users.
+It's not recommended to use a pipe as data output with Intel PT because
+of the following reason.
+
+Essentially the auxtrace buffers do not behave like the regular perf
+event buffers.  That is because the head and tail are updated by
+software, but in the auxtrace case the data is written by hardware.
+So the head and tail do not get updated as data is written.
+
+In the Intel PT case, the head and tail are updated only when the trace
+is disabled by software, for example:
+    - full-trace, system wide : when buffer passes watermark
+    - full-trace, not system-wide : when buffer passes watermark or
+                                    context switches
+    - snapshot mode : as above but also when a snapshot is made
+    - sample mode : as above but also when a sample is made
+
+That means finished-round ordering doesn't work.  An auxtrace buffer
+can turn up that has data that extends back in time, possibly to the
+very beginning of tracing.
+
+For a perf.data file, that problem is solved by going through the trace
+and queuing up the auxtrace buffers in advance.
+
+For pipe mode, the order of events and timestamps can presumably
+be messed up.
+
+
+EXAMPLE
+-------
+
+Examples can be found on perf wiki page "Perf tools support for Intel® Processor Trace":
+
+https://perf.wiki.kernel.org/index.php/Perf_tools_support_for_Intel%C2%AE_Processor_Trace
+
 
 SEE ALSO
 --------
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/Documentation/perf-script.txt
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/Documentation/perf-script.txt
@@ -423,9 +423,10 @@
 	will be printed. Each entry has function name and file/line. Enabled by
 	default, disable with --no-inline.
 
---insn-trace::
-	Show instruction stream for intel_pt traces. Combine with --xed to
-	show disassembly.
+--insn-trace[=<raw|disasm>]::
+	Show instruction stream in bytes (raw) or disassembled (disasm)
+	for intel_pt traces. The default is 'raw'. To use xed, combine
+	'raw' with --xed to show disassembly done by xed.
 
 --xed::
 	Run xed disassembler on output. Requires installing the xed disassembler.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/Makefile.config
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/Makefile.config
@@ -143,7 +143,10 @@
 ifdef CSINCLUDES
   LIBOPENCSD_CFLAGS := -I$(CSINCLUDES)
 endif
-OPENCSDLIBS := -lopencsd_c_api -lopencsd -lstdc++
+OPENCSDLIBS := -lopencsd_c_api -lopencsd
+ifeq ($(findstring -static,${LDFLAGS}),-static)
+  OPENCSDLIBS += -lstdc++
+endif
 ifdef CSLIBS
   LIBOPENCSD_LDFLAGS := -L$(CSLIBS)
 endif
@@ -234,18 +237,33 @@
 endif
 
 # Try different combinations to accommodate systems that only have
-# python[2][-config] in weird combinations but always preferring
-# python2 and python2-config as per pep-0394. If python2 or python
-# aren't found, then python3 is used.
-PYTHON_AUTO := python
-PYTHON_AUTO := $(if $(call get-executable,python3),python3,$(PYTHON_AUTO))
-PYTHON_AUTO := $(if $(call get-executable,python),python,$(PYTHON_AUTO))
-PYTHON_AUTO := $(if $(call get-executable,python2),python2,$(PYTHON_AUTO))
-override PYTHON := $(call get-executable-or-default,PYTHON,$(PYTHON_AUTO))
-PYTHON_AUTO_CONFIG := \
-  $(if $(call get-executable,$(PYTHON)-config),$(PYTHON)-config,python-config)
-override PYTHON_CONFIG := \
-  $(call get-executable-or-default,PYTHON_CONFIG,$(PYTHON_AUTO_CONFIG))
+# python[2][3]-config in weird combinations in the following order of
+# priority from lowest to highest:
+#   * python3-config
+#   * python-config
+#   * python2-config as per pep-0394.
+#   * $(PYTHON)-config (If PYTHON is user supplied but PYTHON_CONFIG isn't)
+#
+PYTHON_AUTO := python-config
+PYTHON_AUTO := $(if $(call get-executable,python3-config),python3-config,$(PYTHON_AUTO))
+PYTHON_AUTO := $(if $(call get-executable,python-config),python-config,$(PYTHON_AUTO))
+PYTHON_AUTO := $(if $(call get-executable,python2-config),python2-config,$(PYTHON_AUTO))
+
+# If PYTHON is defined but PYTHON_CONFIG isn't, then take $(PYTHON)-config as if it was the user
+# supplied value for PYTHON_CONFIG. Because it's "user supplied", error out if it doesn't exist.
+ifdef PYTHON
+  ifndef PYTHON_CONFIG
+    PYTHON_CONFIG_AUTO := $(call get-executable,$(PYTHON)-config)
+    PYTHON_CONFIG := $(if $(PYTHON_CONFIG_AUTO),$(PYTHON_CONFIG_AUTO),\
+                          $(call $(error $(PYTHON)-config not found)))
+  endif
+endif
+
+# Select either auto detected python and python-config or use user supplied values if they are
+# defined. get-executable-or-default fails with an error if the first argument is supplied but
+# doesn't exist.
+override PYTHON_CONFIG := $(call get-executable-or-default,PYTHON_CONFIG,$(PYTHON_AUTO))
+override PYTHON := $(call get-executable-or-default,PYTHON,$(subst -config,,$(PYTHON_CONFIG)))
 
 grep-libs  = $(filter -l%,$(1))
 strip-libs  = $(filter-out -l%,$(1))
@@ -267,16 +285,18 @@
   PYTHON_EMBED_LIBADD := $(call grep-libs,$(PYTHON_EMBED_LDOPTS)) -lutil
   PYTHON_EMBED_CCOPTS := $(shell $(PYTHON_CONFIG_SQ) --includes 2>/dev/null)
   FLAGS_PYTHON_EMBED := $(PYTHON_EMBED_CCOPTS) $(PYTHON_EMBED_LDOPTS)
+  ifeq ($(CC_NO_CLANG), 0)
+    PYTHON_EMBED_CCOPTS := $(filter-out -ffat-lto-objects, $(PYTHON_EMBED_CCOPTS))
+  endif
 endif
 
 FEATURE_CHECK_CFLAGS-libpython := $(PYTHON_EMBED_CCOPTS)
 FEATURE_CHECK_LDFLAGS-libpython := $(PYTHON_EMBED_LDOPTS)
-FEATURE_CHECK_CFLAGS-libpython-version := $(PYTHON_EMBED_CCOPTS)
-FEATURE_CHECK_LDFLAGS-libpython-version := $(PYTHON_EMBED_LDOPTS)
 
 FEATURE_CHECK_LDFLAGS-libaio = -lrt
 
 FEATURE_CHECK_LDFLAGS-disassembler-four-args = -lbfd -lopcodes -ldl
+FEATURE_CHECK_LDFLAGS-disassembler-init-styled = -lbfd -lopcodes -ldl
 
 CORE_CFLAGS += -fno-omit-frame-pointer
 CORE_CFLAGS += -ggdb3
@@ -544,9 +564,16 @@
         ifeq ($(feature-libbpf), 1)
           EXTLIBS += -lbpf
           $(call detected,CONFIG_LIBBPF_DYNAMIC)
+
+          $(call feature_check,libbpf-btf__load_from_kernel_by_id)
+          ifeq ($(feature-libbpf-btf__load_from_kernel_by_id), 1)
+            CFLAGS += -DHAVE_LIBBPF_BTF__LOAD_FROM_KERNEL_BY_ID
+          endif
         else
           dummy := $(error Error: No libbpf devel library found, please install libbpf-devel);
         endif
+      else
+	CFLAGS += -DHAVE_LIBBPF_BTF__LOAD_FROM_KERNEL_BY_ID
       endif
     endif
 
@@ -784,6 +811,9 @@
     LDFLAGS += $(PERL_EMBED_LDFLAGS)
     EXTLIBS += $(PERL_EMBED_LIBADD)
     CFLAGS += -DHAVE_LIBPERL_SUPPORT
+    ifeq ($(CC_NO_CLANG), 0)
+      CFLAGS += -Wno-compound-token-split-by-macro
+    endif
     $(call detected,CONFIG_LIBPERL)
   endif
 endif
@@ -827,6 +857,10 @@
   endif
 endif
 
+ifdef HAVE_NO_LIBBFD
+  feature-libbfd := 0
+  $(info libbfd overidden OFF)
+else
 
 ifndef NO_LIBBFD
   ifeq ($(feature-libbfd), 1)
@@ -843,13 +877,16 @@
     ifeq ($(feature-libbfd-liberty), 1)
       EXTLIBS += -lbfd -lopcodes -liberty
       FEATURE_CHECK_LDFLAGS-disassembler-four-args += -liberty -ldl
+      FEATURE_CHECK_LDFLAGS-disassembler-init-styled += -liberty -ldl
     else
       ifeq ($(feature-libbfd-liberty-z), 1)
         EXTLIBS += -lbfd -lopcodes -liberty -lz
         FEATURE_CHECK_LDFLAGS-disassembler-four-args += -liberty -lz -ldl
+        FEATURE_CHECK_LDFLAGS-disassembler-init-styled += -liberty -lz -ldl
       endif
     endif
     $(call feature_check,disassembler-four-args)
+    $(call feature_check,disassembler-init-styled)
   endif
 
   ifeq ($(feature-libbfd-buildid), 1)
@@ -859,6 +896,8 @@
   endif
 endif
 
+endif
+
 ifdef NO_DEMANGLE
   CFLAGS += -DNO_DEMANGLE
 else
@@ -963,6 +1002,10 @@
     CFLAGS += -DDISASM_FOUR_ARGS_SIGNATURE
 endif
 
+ifeq ($(feature-disassembler-init-styled), 1)
+    CFLAGS += -DDISASM_INIT_STYLED
+endif
+
 ifeq (${IS_64_BIT}, 1)
   ifndef NO_PERF_READ_VDSO32
     $(call feature_check,compile-32)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/arm64/util/Build
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/arm64/util/Build
@@ -1,5 +1,4 @@
 perf-y += header.o
-perf-y += machine.o
 perf-y += perf_regs.o
 perf-y += tsc.o
 perf-y += pmu.o
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/arm64/util/arm-spe.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/arm64/util/arm-spe.c
@@ -154,6 +154,12 @@
 		arm_spe_set_timestamp(itr, arm_spe_evsel);
 	}
 
+	/*
+	 * Set this only so that perf report knows that SPE generates memory info. It has no effect
+	 * on the opening of the event or the SPE data produced.
+	 */
+	evsel__set_sample_bit(arm_spe_evsel, DATA_SRC);
+
 	/* Add dummy event to keep tracking */
 	err = parse_events(evlist, "dummy:u", NULL);
 	if (err)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/powerpc/util/Build
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/powerpc/util/Build
@@ -1,5 +1,4 @@
 perf-y += header.o
-perf-y += machine.o
 perf-y += kvm-stat.o
 perf-y += perf_regs.o
 perf-y += mem-events.o
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/s390/util/machine.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/s390/util/machine.c
@@ -35,19 +35,3 @@
 
 	return 0;
 }
-
-/* On s390 kernel text segment start is located at very low memory addresses,
- * for example 0x10000. Modules are located at very high memory addresses,
- * for example 0x3ff xxxx xxxx. The gap between end of kernel text segment
- * and beginning of first module's text segment is very big.
- * Therefore do not fill this gap and do not assign it to the kernel dso map.
- */
-void arch__symbols__fixup_end(struct symbol *p, struct symbol *c)
-{
-	if (strchr(p->name, '[') == NULL && strchr(c->name, '['))
-		/* Last kernel symbol mapped to end of page */
-		p->end = roundup(p->end, page_size);
-	else
-		p->end = c->start;
-	pr_debug4("%s sym:%s end:%#" PRIx64 "\n", __func__, p->name, p->end);
-}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/x86/tests/intel-pt-pkt-decoder-test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/x86/tests/intel-pt-pkt-decoder-test.c
@@ -166,6 +166,14 @@
 	{2, {0x02, 0xb3}, INTEL_PT_BLK_4_CTX, {INTEL_PT_BEP_IP, 0, 0}, 0, 0 },
 	{2, {0x02, 0x33}, INTEL_PT_BLK_8_CTX, {INTEL_PT_BEP, 0, 0}, 0, 0 },
 	{2, {0x02, 0xb3}, INTEL_PT_BLK_8_CTX, {INTEL_PT_BEP_IP, 0, 0}, 0, 0 },
+	/* Control Flow Event Packet */
+	{4, {0x02, 0x13, 0x01, 0x03}, 0, {INTEL_PT_CFE, 1, 3}, 0, 0 },
+	{4, {0x02, 0x13, 0x81, 0x03}, 0, {INTEL_PT_CFE_IP, 1, 3}, 0, 0 },
+	{4, {0x02, 0x13, 0x1f, 0x00}, 0, {INTEL_PT_CFE, 0x1f, 0}, 0, 0 },
+	{4, {0x02, 0x13, 0x9f, 0xff}, 0, {INTEL_PT_CFE_IP, 0x1f, 0xff}, 0, 0 },
+	/*  */
+	{11, {0x02, 0x53, 0x09, 1, 2, 3, 4, 5, 6, 7}, 0, {INTEL_PT_EVD, 0x09, 0x7060504030201}, 0, 0 },
+	{11, {0x02, 0x53, 0x3f, 2, 3, 4, 5, 6, 7, 8}, 0, {INTEL_PT_EVD, 0x3f, 0x8070605040302}, 0, 0 },
 	/* Terminator */
 	{0, {0}, 0, {0, 0, 0}, 0, 0 },
 };
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/x86/util/intel-pt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/x86/util/intel-pt.c
@@ -31,6 +31,7 @@
 #include "../../../util/tsc.h"
 #include <internal/lib.h> // page_size
 #include "../../../util/intel-pt.h"
+#include <api/fs/fs.h>
 
 #define KiB(x) ((x) * 1024)
 #define MiB(x) ((x) * 1024 * 1024)
@@ -438,6 +439,16 @@
 	return 0;
 }
 
+static bool intel_pt_exclude_guest(void)
+{
+	int pt_mode;
+
+	if (sysfs__read_int("module/kvm_intel/parameters/pt_mode", &pt_mode))
+		pt_mode = 0;
+
+	return pt_mode == 1;
+}
+
 static void intel_pt_valid_str(char *str, size_t len, u64 valid)
 {
 	unsigned int val, last = 0, state = 1;
@@ -641,6 +652,7 @@
 			}
 			evsel->core.attr.freq = 0;
 			evsel->core.attr.sample_period = 1;
+			evsel->core.attr.exclude_guest = intel_pt_exclude_guest();
 			evsel->no_aux_samples = true;
 			intel_pt_evsel = evsel;
 			opts->full_auxtrace = true;
@@ -777,7 +789,8 @@
 	}
 
 	if (!opts->auxtrace_snapshot_mode && !opts->auxtrace_sample_mode) {
-		u32 aux_watermark = opts->auxtrace_mmap_pages * page_size / 4;
+		size_t aw = opts->auxtrace_mmap_pages * (size_t)page_size / 4;
+		u32 aux_watermark = aw > UINT_MAX ? UINT_MAX : aw;
 
 		intel_pt_evsel->core.attr.aux_watermark = aux_watermark;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/arch/x86/util/perf_regs.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/arch/x86/util/perf_regs.c
@@ -9,6 +9,8 @@
 #include "../../../util/perf_regs.h"
 #include "../../../util/debug.h"
 #include "../../../util/event.h"
+#include "../../../util/pmu.h"
+#include "../../../util/pmu-hybrid.h"
 
 const struct sample_reg sample_reg_masks[] = {
 	SMPL_REG(AX, PERF_REG_X86_AX),
@@ -284,12 +286,22 @@
 		.disabled 		= 1,
 		.exclude_kernel		= 1,
 	};
+	struct perf_pmu *pmu;
 	int fd;
 	/*
 	 * In an unnamed union, init it here to build on older gcc versions
 	 */
 	attr.sample_period = 1;
 
+	if (perf_pmu__has_hybrid()) {
+		/*
+		 * The same register set is supported among different hybrid PMUs.
+		 * Only check the first available one.
+		 */
+		pmu = list_first_entry(&perf_pmu__hybrid_pmus, typeof(*pmu), hybrid_list);
+		attr.config |= (__u64)pmu->type << PERF_PMU_TYPE_SHIFT;
+	}
+
 	event_attr_init(&attr);
 
 	fd = sys_perf_event_open(&attr, 0, -1, -1, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/bench.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/bench.h
@@ -10,25 +10,13 @@
  * The madvise transparent hugepage constants were added in glibc
  * 2.13. For compatibility with older versions of glibc, define these
  * tokens if they are not already defined.
- *
- * PA-RISC uses different madvise values from other architectures and
- * needs to be special-cased.
  */
-#ifdef __hppa__
-# ifndef MADV_HUGEPAGE
-#  define MADV_HUGEPAGE		67
-# endif
-# ifndef MADV_NOHUGEPAGE
-#  define MADV_NOHUGEPAGE	68
-# endif
-#else
 # ifndef MADV_HUGEPAGE
 #  define MADV_HUGEPAGE		14
 # endif
 # ifndef MADV_NOHUGEPAGE
 #  define MADV_NOHUGEPAGE	15
 # endif
-#endif
 
 int bench_numa(int argc, const char **argv);
 int bench_sched_messaging(int argc, const char **argv);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/epoll-wait.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/epoll-wait.c
@@ -406,7 +406,12 @@
 
 	struct worker *w1 = (struct worker *) p1;
 	struct worker *w2 = (struct worker *) p2;
-	return w1->tid > w2->tid;
+
+	if (w1->tid > w2->tid)
+		return 1;
+	if (w1->tid < w2->tid)
+		return -1;
+	return 0;
 }
 
 int bench_epoll_wait(int argc, const char **argv)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/futex-lock-pi.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/futex-lock-pi.c
@@ -233,6 +233,7 @@
 	print_summary();
 
 	free(worker);
+	perf_cpu_map__put(cpu);
 	return ret;
 err:
 	usage_with_options(bench_futex_lock_pi_usage, options);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/futex-requeue.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/futex-requeue.c
@@ -294,6 +294,7 @@
 	print_summary();
 
 	free(worker);
+	perf_cpu_map__put(cpu);
 	return ret;
 err:
 	usage_with_options(bench_futex_requeue_usage, options);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/futex-wake-parallel.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/futex-wake-parallel.c
@@ -329,6 +329,7 @@
 	print_summary();
 
 	free(blocked_worker);
+	perf_cpu_map__put(cpu);
 	return ret;
 }
 #endif /* HAVE_PTHREAD_BARRIER */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/futex-wake.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/futex-wake.c
@@ -222,5 +222,6 @@
 	print_summary();
 
 	free(worker);
+	perf_cpu_map__put(cpu);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/bench/numa.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/bench/numa.c
@@ -1672,7 +1672,7 @@
 		"GB/sec,", "total-speed",	"GB/sec total speed");
 
 	if (g->p.show_details >= 2) {
-		char tname[14 + 2 * 10 + 1];
+		char tname[14 + 2 * 11 + 1];
 		struct thread_data *td;
 		for (p = 0; p < g->p.nr_proc; p++) {
 			for (t = 0; t < g->p.nr_threads; t++) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-bench.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-bench.c
@@ -21,6 +21,7 @@
 #include "builtin.h"
 #include "bench/bench.h"
 
+#include <locale.h>
 #include <stdio.h>
 #include <stdlib.h>
 #include <string.h>
@@ -226,7 +227,6 @@
 		if (!bench->fn)
 			break;
 		printf("# Running %s/%s benchmark...\n", coll->name, bench->name);
-		fflush(stdout);
 
 		argv[1] = bench->name;
 		run_bench(coll->name, bench->name, bench->fn, 1, argv);
@@ -247,6 +247,10 @@
 	struct collection *coll;
 	int ret = 0;
 
+	/* Unbuffered output */
+	setvbuf(stdout, NULL, _IONBF, 0);
+	setlocale(LC_ALL, "");
+
 	if (argc < 2) {
 		/* No collection specified. */
 		print_usage();
@@ -300,7 +304,6 @@
 
 			if (bench_format == BENCH_FORMAT_DEFAULT)
 				printf("# Running '%s/%s' benchmark:\n", coll->name, bench->name);
-			fflush(stdout);
 			ret = run_bench(coll->name, bench->name, bench->fn, argc-1, argv+1);
 			goto end;
 		}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-c2c.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-c2c.c
@@ -924,8 +924,8 @@
 	double per_left;
 	double per_right;
 
-	per_left  = PERCENT(left, lcl_hitm);
-	per_right = PERCENT(right, lcl_hitm);
+	per_left  = PERCENT(left, rmt_hitm);
+	per_right = PERCENT(right, rmt_hitm);
 
 	return per_left - per_right;
 }
@@ -2733,9 +2733,7 @@
 		   "the input file to process"),
 	OPT_INCR('N', "node-info", &c2c.node_info,
 		 "show extra node info in report (repeat for more info)"),
-#ifdef HAVE_SLANG_SUPPORT
 	OPT_BOOLEAN(0, "stdio", &c2c.use_stdio, "Use the stdio interface"),
-#endif
 	OPT_BOOLEAN(0, "stats", &c2c.stats_only,
 		    "Display only statistic tables (implies --stdio)"),
 	OPT_BOOLEAN(0, "full-symbols", &c2c.symbol_full,
@@ -2765,6 +2763,10 @@
 	if (argc)
 		usage_with_options(report_c2c_usage, options);
 
+#ifndef HAVE_SLANG_SUPPORT
+	c2c.use_stdio = true;
+#endif
+
 	if (c2c.stats_only)
 		c2c.use_stdio = true;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-inject.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-inject.c
@@ -142,14 +142,14 @@
 
 #ifdef HAVE_AUXTRACE_SUPPORT
 
-static int copy_bytes(struct perf_inject *inject, int fd, off_t size)
+static int copy_bytes(struct perf_inject *inject, struct perf_data *data, off_t size)
 {
 	char buf[4096];
 	ssize_t ssz;
 	int ret;
 
 	while (size > 0) {
-		ssz = read(fd, buf, min(size, (off_t)sizeof(buf)));
+		ssz = perf_data__read(data, buf, min(size, (off_t)sizeof(buf)));
 		if (ssz < 0)
 			return -errno;
 		ret = output_bytes(inject, buf, ssz);
@@ -187,7 +187,7 @@
 		ret = output_bytes(inject, event, event->header.size);
 		if (ret < 0)
 			return ret;
-		ret = copy_bytes(inject, perf_data__fd(session->data),
+		ret = copy_bytes(inject, session->data,
 				 event->auxtrace.size);
 	} else {
 		ret = output_bytes(inject, event,
@@ -463,6 +463,7 @@
 			dso->hit = 1;
 		}
 		dso__put(dso);
+		perf_event__repipe(tool, event, sample, machine);
 		return 0;
 	}
 
@@ -755,12 +756,16 @@
 	return inject->itrace_synth_opts.vm_tm_corr_args ? 0 : -ENOMEM;
 }
 
+static int output_fd(struct perf_inject *inject)
+{
+	return inject->in_place_update ? -1 : perf_data__fd(&inject->output);
+}
+
 static int __cmd_inject(struct perf_inject *inject)
 {
 	int ret = -EINVAL;
 	struct perf_session *session = inject->session;
-	struct perf_data *data_out = &inject->output;
-	int fd = inject->in_place_update ? -1 : perf_data__fd(data_out);
+	int fd = output_fd(inject);
 	u64 output_data_offset;
 
 	signal(SIGINT, sig_handler);
@@ -819,7 +824,7 @@
 		inject->tool.ordered_events = true;
 		inject->tool.ordering_requires_timestamps = true;
 		/* Allow space in the header for new attributes */
-		output_data_offset = 4096;
+		output_data_offset = roundup(8192 + session->header.data_offset, 4096);
 		if (inject->strip)
 			strip_init(inject);
 	}
@@ -1006,7 +1011,7 @@
 	}
 
 	inject.session = __perf_session__new(&data, repipe,
-					     perf_data__fd(&inject.output),
+					     output_fd(&inject),
 					     &inject.tool);
 	if (IS_ERR(inject.session)) {
 		ret = PTR_ERR(inject.session);
@@ -1069,7 +1074,8 @@
 	zstd_fini(&(inject.session->zstd_data));
 	perf_session__delete(inject.session);
 out_close_output:
-	perf_data__close(&inject.output);
+	if (!inject.in_place_update)
+		perf_data__close(&inject.output);
 	free(inject.itrace_synth_opts.vm_tm_corr_args);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-mem.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-mem.c
@@ -358,6 +358,7 @@
 		rep_argv[i] = argv[j];
 
 	ret = cmd_report(i, rep_argv);
+	free(new_sort_order);
 	free(rep_argv);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-record.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-record.c
@@ -1277,8 +1277,8 @@
 record__switch_output(struct record *rec, bool at_exit)
 {
 	struct perf_data *data = &rec->data;
+	char *new_filename = NULL;
 	int fd, err;
-	char *new_filename;
 
 	/* Same Size:      "2015122520103046"*/
 	char timestamp[] = "InvalidTimestamp";
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-report.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-report.c
@@ -349,6 +349,7 @@
 	struct perf_session *session = rep->session;
 	u64 sample_type = evlist__combined_sample_type(session->evlist);
 	bool is_pipe = perf_data__is_pipe(session->data);
+	struct evsel *evsel;
 
 	if (session->itrace_synth_opts->callchain ||
 	    session->itrace_synth_opts->add_callchain ||
@@ -403,6 +404,19 @@
 	}
 
 	if (sort__mode == SORT_MODE__MEMORY) {
+		/*
+		 * FIXUP: prior to kernel 5.18, Arm SPE missed to set
+		 * PERF_SAMPLE_DATA_SRC bit in sample type.  For backward
+		 * compatibility, set the bit if it's an old perf data file.
+		 */
+		evlist__for_each_entry(session->evlist, evsel) {
+			if (strstr(evsel->name, "arm_spe") &&
+				!(sample_type & PERF_SAMPLE_DATA_SRC)) {
+				evsel->core.attr.sample_type |= PERF_SAMPLE_DATA_SRC;
+				sample_type |= PERF_SAMPLE_DATA_SRC;
+			}
+		}
+
 		if (!is_pipe && !(sample_type & PERF_SAMPLE_DATA_SRC)) {
 			ui__error("Selected --mem-mode but no mem data. "
 				  "Did you call perf record without -d?\n");
@@ -619,14 +633,17 @@
 	int ret;
 	struct perf_session *session = rep->session;
 	struct evlist *evlist = session->evlist;
-	const char *help = perf_tip(system_path(TIPDIR));
+	char *help = NULL, *path = NULL;
 
-	if (help == NULL) {
+	path = system_path(TIPDIR);
+	if (perf_tip(&help, path) || help == NULL) {
 		/* fallback for people who don't install perf ;-) */
-		help = perf_tip(DOCDIR);
-		if (help == NULL)
-			help = "Cannot load tips.txt file, please install perf!";
+		free(path);
+		path = system_path(DOCDIR);
+		if (perf_tip(&help, path) || help == NULL)
+			help = strdup("Cannot load tips.txt file, please install perf!");
 	}
+	free(path);
 
 	switch (use_browser) {
 	case 1:
@@ -651,7 +668,7 @@
 		ret = evlist__tty_browse_hists(evlist, rep, help);
 		break;
 	}
-
+	free(help);
 	return ret;
 }
 
@@ -1291,7 +1308,7 @@
 	OPT_STRING(0, "objdump", &report.annotation_opts.objdump_path, "path",
 		   "objdump binary to use for disassembly and annotations"),
 	OPT_BOOLEAN(0, "demangle", &symbol_conf.demangle,
-		    "Disable symbol demangling"),
+		    "Symbol demangling. Enabled by default, use --no-demangle to disable."),
 	OPT_BOOLEAN(0, "demangle-kernel", &symbol_conf.demangle_kernel,
 		    "Enable kernel symbol demangling"),
 	OPT_BOOLEAN(0, "mem-mode", &report.mem_mode, "mem access profile"),
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-sched.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-sched.c
@@ -2577,9 +2577,12 @@
 	 * - previous sched event is out of window - we are done
 	 * - sample time is beyond window user cares about - reset it
 	 *   to close out stats for time window interest
+	 * - If tprev is 0, that is, sched_in event for current task is
+	 *   not recorded, cannot determine whether sched_in event is
+	 *   within time window interest - ignore it
 	 */
 	if (ptime->end) {
-		if (tprev > ptime->end)
+		if (!tprev || tprev > ptime->end)
 			goto out;
 
 		if (t > ptime->end)
@@ -3027,7 +3030,8 @@
 
 	if (perf_time__parse_str(&sched->ptime, sched->time_str) != 0) {
 		pr_err("Invalid time string\n");
-		return -EINVAL;
+		err = -EINVAL;
+		goto out;
 	}
 
 	if (timehist_check_attr(sched, evlist) != 0)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-script.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-script.c
@@ -435,6 +435,9 @@
 	struct perf_event_attr *attr = &evsel->core.attr;
 	bool allow_user_set;
 
+	if (evsel__is_dummy_event(evsel))
+		return 0;
+
 	if (perf_header__has_feat(&session->header, HEADER_STAT))
 		return 0;
 
@@ -455,7 +458,7 @@
 		return -EINVAL;
 
 	if (PRINT_FIELD(DATA_SRC) &&
-	    evsel__check_stype(evsel, PERF_SAMPLE_DATA_SRC, "DATA_SRC", PERF_OUTPUT_DATA_SRC))
+	    evsel__do_check_stype(evsel, PERF_SAMPLE_DATA_SRC, "DATA_SRC", PERF_OUTPUT_DATA_SRC, allow_user_set))
 		return -EINVAL;
 
 	if (PRINT_FIELD(WEIGHT) &&
@@ -2257,6 +2260,9 @@
 	return ret;
 }
 
+// Used when scr->per_event_dump is not set
+static struct evsel_script es_stdout;
+
 static int process_attr(struct perf_tool *tool, union perf_event *event,
 			struct evlist **pevlist)
 {
@@ -2265,7 +2271,6 @@
 	struct evsel *evsel, *pos;
 	u64 sample_type;
 	int err;
-	static struct evsel_script *es;
 
 	err = perf_event__process_attr(tool, event, pevlist);
 	if (err)
@@ -2275,14 +2280,13 @@
 	evsel = evlist__last(*pevlist);
 
 	if (!evsel->priv) {
-		if (scr->per_event_dump) {
+		if (scr->per_event_dump) { 
 			evsel->priv = evsel_script__new(evsel, scr->session->data);
-		} else {
-			es = zalloc(sizeof(*es));
-			if (!es)
+			if (!evsel->priv)
 				return -ENOMEM;
-			es->fp = stdout;
-			evsel->priv = es;
+		} else { // Replicate what is done in perf_script__setup_per_event_dump()
+			es_stdout.fp = stdout;
+			evsel->priv = &es_stdout;
 		}
 	}
 
@@ -2463,7 +2467,7 @@
 	if (perf_event__process_switch(tool, event, sample, machine) < 0)
 		return -1;
 
-	if (scripting_ops && scripting_ops->process_switch)
+	if (scripting_ops && scripting_ops->process_switch && !filter_cpu(sample))
 		scripting_ops->process_switch(event, sample, machine);
 
 	if (!script->show_switch_events)
@@ -2588,7 +2592,6 @@
 static int perf_script__setup_per_event_dump(struct perf_script *script)
 {
 	struct evsel *evsel;
-	static struct evsel_script es_stdout;
 
 	if (script->per_event_dump)
 		return perf_script__fopen_per_event_dump(script);
@@ -3582,11 +3585,25 @@
 #endif
 
 static int parse_insn_trace(const struct option *opt __maybe_unused,
-			    const char *str __maybe_unused,
-			    int unset __maybe_unused)
+			    const char *str, int unset __maybe_unused)
 {
-	parse_output_fields(NULL, "+insn,-event,-period", 0);
-	itrace_parse_synth_opts(opt, "i0ns", 0);
+	const char *fields = "+insn,-event,-period";
+	int ret;
+
+	if (str) {
+		if (strcmp(str, "disasm") == 0)
+			fields = "+disasm,-event,-period";
+		else if (strlen(str) != 0 && strcmp(str, "raw") != 0) {
+			fprintf(stderr, "Only accept raw|disasm\n");
+			return -EINVAL;
+		}
+	}
+
+	ret = parse_output_fields(NULL, fields, 0);
+	if (ret < 0)
+		return ret;
+
+	itrace_parse_synth_opts(opt, "i0nse", 0);
 	symbol_conf.nanosecs = true;
 	return 0;
 }
@@ -3725,7 +3742,7 @@
 		   "only consider these symbols"),
 	OPT_INTEGER(0, "addr-range", &symbol_conf.addr_range,
 		    "Use with -S to list traced records within address range"),
-	OPT_CALLBACK_OPTARG(0, "insn-trace", &itrace_synth_opts, NULL, NULL,
+	OPT_CALLBACK_OPTARG(0, "insn-trace", &itrace_synth_opts, NULL, "raw|disasm",
 			"Decode instructions from itrace", parse_insn_trace),
 	OPT_CALLBACK_OPTARG(0, "xed", NULL, NULL, NULL,
 			"Run xed disassembler on output", parse_xed),
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-stat.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-stat.c
@@ -405,36 +405,33 @@
 
 static int read_affinity_counters(struct timespec *rs)
 {
-	struct evsel *counter;
-	struct affinity affinity;
-	int i, ncpus, cpu;
+	struct evlist_cpu_iterator evlist_cpu_itr;
+	struct affinity saved_affinity, *affinity;
 
 	if (all_counters_use_bpf)
 		return 0;
 
-	if (affinity__setup(&affinity) < 0)
+	if (!target__has_cpu(&target) || target__has_per_thread(&target))
+		affinity = NULL;
+	else if (affinity__setup(&saved_affinity) < 0)
 		return -1;
+	else
+		affinity = &saved_affinity;
 
-	ncpus = perf_cpu_map__nr(evsel_list->core.all_cpus);
-	if (!target__has_cpu(&target) || target__has_per_thread(&target))
-		ncpus = 1;
-	evlist__for_each_cpu(evsel_list, i, cpu) {
-		if (i >= ncpus)
-			break;
-		affinity__set(&affinity, cpu);
+	evlist__for_each_cpu(evlist_cpu_itr, evsel_list, affinity) {
+		struct evsel *counter = evlist_cpu_itr.evsel;
 
-		evlist__for_each_entry(evsel_list, counter) {
-			if (evsel__cpu_iter_skip(counter, cpu))
-				continue;
-			if (evsel__is_bpf(counter))
-				continue;
-			if (!counter->err) {
-				counter->err = read_counter_cpu(counter, rs,
-								counter->cpu_iter - 1);
-			}
+		if (evsel__is_bpf(counter))
+			continue;
+
+		if (!counter->err) {
+			counter->err = read_counter_cpu(counter, rs,
+							evlist_cpu_itr.cpu_map_idx);
 		}
 	}
-	affinity__cleanup(&affinity);
+	if (affinity)
+		affinity__cleanup(&saved_affinity);
+
 	return 0;
 }
 
@@ -558,26 +555,9 @@
 			return err;
 	}
 
-	if (stat_config.initial_delay < 0) {
-		pr_info(EVLIST_DISABLED_MSG);
-		return 0;
-	}
-
-	if (stat_config.initial_delay > 0) {
-		pr_info(EVLIST_DISABLED_MSG);
-		usleep(stat_config.initial_delay * USEC_PER_MSEC);
-	}
-
-	/*
-	 * We need to enable counters only if:
-	 * - we don't have tracee (attaching to task or cpu)
-	 * - we have initial delay configured
-	 */
-	if (!target__none(&target) || stat_config.initial_delay) {
+	if (!target__enable_on_exec(&target)) {
 		if (!all_counters_use_bpf)
 			evlist__enable(evsel_list);
-		if (stat_config.initial_delay > 0)
-			pr_info(EVLIST_ENABLED_MSG);
 	}
 	return 0;
 }
@@ -788,8 +768,9 @@
 	int status = 0;
 	const bool forks = (argc > 0);
 	bool is_pipe = STAT_RECORD ? perf_stat.data.is_pipe : false;
+	struct evlist_cpu_iterator evlist_cpu_itr;
 	struct affinity affinity;
-	int i, cpu, err;
+	int err;
 	bool second_pass = false;
 
 	if (forks) {
@@ -807,62 +788,60 @@
 		return -1;
 
 	evlist__for_each_entry(evsel_list, counter) {
+		counter->reset_group = false;
 		if (bpf_counter__load(counter, &target))
 			return -1;
-		if (!evsel__is_bpf(counter))
+		if (!(evsel__is_bperf(counter)))
 			all_counters_use_bpf = false;
 	}
 
-	evlist__for_each_cpu (evsel_list, i, cpu) {
+	evlist__for_each_cpu(evlist_cpu_itr, evsel_list, &affinity) {
+		counter = evlist_cpu_itr.evsel;
+
 		/*
 		 * bperf calls evsel__open_per_cpu() in bperf__load(), so
 		 * no need to call it again here.
 		 */
 		if (target.use_bpf)
 			break;
-		affinity__set(&affinity, cpu);
 
-		evlist__for_each_entry(evsel_list, counter) {
-			if (evsel__cpu_iter_skip(counter, cpu))
-				continue;
-			if (counter->reset_group || counter->errored)
-				continue;
-			if (evsel__is_bpf(counter))
-				continue;
+		if (counter->reset_group || counter->errored)
+			continue;
+		if (evsel__is_bperf(counter))
+			continue;
 try_again:
-			if (create_perf_stat_counter(counter, &stat_config, &target,
-						     counter->cpu_iter - 1) < 0) {
-
-				/*
-				 * Weak group failed. We cannot just undo this here
-				 * because earlier CPUs might be in group mode, and the kernel
-				 * doesn't support mixing group and non group reads. Defer
-				 * it to later.
-				 * Don't close here because we're in the wrong affinity.
-				 */
-				if ((errno == EINVAL || errno == EBADF) &&
-				    evsel__leader(counter) != counter &&
-				    counter->weak_group) {
-					evlist__reset_weak_group(evsel_list, counter, false);
-					assert(counter->reset_group);
-					second_pass = true;
-					continue;
-				}
+		if (create_perf_stat_counter(counter, &stat_config, &target,
+					     evlist_cpu_itr.cpu_map_idx) < 0) {
 
-				switch (stat_handle_error(counter)) {
-				case COUNTER_FATAL:
-					return -1;
-				case COUNTER_RETRY:
-					goto try_again;
-				case COUNTER_SKIP:
-					continue;
-				default:
-					break;
-				}
+			/*
+			 * Weak group failed. We cannot just undo this here
+			 * because earlier CPUs might be in group mode, and the kernel
+			 * doesn't support mixing group and non group reads. Defer
+			 * it to later.
+			 * Don't close here because we're in the wrong affinity.
+			 */
+			if ((errno == EINVAL || errno == EBADF) &&
+				evsel__leader(counter) != counter &&
+				counter->weak_group) {
+				evlist__reset_weak_group(evsel_list, counter, false);
+				assert(counter->reset_group);
+				second_pass = true;
+				continue;
+			}
 
+			switch (stat_handle_error(counter)) {
+			case COUNTER_FATAL:
+				return -1;
+			case COUNTER_RETRY:
+				goto try_again;
+			case COUNTER_SKIP:
+				continue;
+			default:
+				break;
 			}
-			counter->supported = true;
+
 		}
+		counter->supported = true;
 	}
 
 	if (second_pass) {
@@ -871,42 +850,40 @@
 		 * and also close errored counters.
 		 */
 
-		evlist__for_each_cpu(evsel_list, i, cpu) {
-			affinity__set(&affinity, cpu);
-			/* First close errored or weak retry */
-			evlist__for_each_entry(evsel_list, counter) {
-				if (!counter->reset_group && !counter->errored)
-					continue;
-				if (evsel__cpu_iter_skip_no_inc(counter, cpu))
-					continue;
-				perf_evsel__close_cpu(&counter->core, counter->cpu_iter);
-			}
-			/* Now reopen weak */
-			evlist__for_each_entry(evsel_list, counter) {
-				if (!counter->reset_group && !counter->errored)
-					continue;
-				if (evsel__cpu_iter_skip(counter, cpu))
-					continue;
-				if (!counter->reset_group)
-					continue;
+		/* First close errored or weak retry */
+		evlist__for_each_cpu(evlist_cpu_itr, evsel_list, &affinity) {
+			counter = evlist_cpu_itr.evsel;
+
+			if (!counter->reset_group && !counter->errored)
+				continue;
+
+			perf_evsel__close_cpu(&counter->core, evlist_cpu_itr.cpu_map_idx);
+		}
+		/* Now reopen weak */
+		evlist__for_each_cpu(evlist_cpu_itr, evsel_list, &affinity) {
+			counter = evlist_cpu_itr.evsel;
+
+			if (!counter->reset_group && !counter->errored)
+				continue;
+			if (!counter->reset_group)
+				continue;
 try_again_reset:
-				pr_debug2("reopening weak %s\n", evsel__name(counter));
-				if (create_perf_stat_counter(counter, &stat_config, &target,
-							     counter->cpu_iter - 1) < 0) {
-
-					switch (stat_handle_error(counter)) {
-					case COUNTER_FATAL:
-						return -1;
-					case COUNTER_RETRY:
-						goto try_again_reset;
-					case COUNTER_SKIP:
-						continue;
-					default:
-						break;
-					}
+			pr_debug2("reopening weak %s\n", evsel__name(counter));
+			if (create_perf_stat_counter(counter, &stat_config, &target,
+						     evlist_cpu_itr.cpu_map_idx) < 0) {
+
+				switch (stat_handle_error(counter)) {
+				case COUNTER_FATAL:
+					return -1;
+				case COUNTER_RETRY:
+					goto try_again_reset;
+				case COUNTER_SKIP:
+					continue;
+				default:
+					break;
 				}
-				counter->supported = true;
 			}
+			counter->supported = true;
 		}
 	}
 	affinity__cleanup(&affinity);
@@ -952,18 +929,31 @@
 			return err;
 	}
 
-	/*
-	 * Enable counters and exec the command:
-	 */
-	if (forks) {
+	if (target.initial_delay) {
+		pr_info(EVLIST_DISABLED_MSG);
+	} else {
+		err = enable_counters();
+		if (err)
+			return -1;
+	}
+
+	/* Exec the command, if any */
+	if (forks)
 		evlist__start_workload(evsel_list);
+
+	if (target.initial_delay > 0) {
+		usleep(target.initial_delay * USEC_PER_MSEC);
 		err = enable_counters();
 		if (err)
 			return -1;
 
-		t0 = rdclock();
-		clock_gettime(CLOCK_MONOTONIC, &ref_time);
+		pr_info(EVLIST_ENABLED_MSG);
+	}
+
+	t0 = rdclock();
+	clock_gettime(CLOCK_MONOTONIC, &ref_time);
 
+	if (forks) {
 		if (interval || timeout || evlist__ctlfd_initialized(evsel_list))
 			status = dispatch_events(forks, timeout, interval, &times);
 		if (child_pid != -1) {
@@ -981,13 +971,6 @@
 		if (WIFSIGNALED(status))
 			psignal(WTERMSIG(status), argv[0]);
 	} else {
-		err = enable_counters();
-		if (err)
-			return -1;
-
-		t0 = rdclock();
-		clock_gettime(CLOCK_MONOTONIC, &ref_time);
-
 		status = dispatch_events(forks, timeout, interval, &times);
 	}
 
@@ -1249,7 +1232,7 @@
 		     "aggregate counts per thread", AGGR_THREAD),
 	OPT_SET_UINT(0, "per-node", &stat_config.aggr_mode,
 		     "aggregate counts per numa node", AGGR_NODE),
-	OPT_INTEGER('D', "delay", &stat_config.initial_delay,
+	OPT_INTEGER('D', "delay", &target.initial_delay,
 		    "ms to wait before starting measurement after program start (-1: start with events disabled)"),
 	OPT_CALLBACK_NOOPT(0, "metric-only", &stat_config.metric_only, NULL,
 			"Only print computed metrics. No raw values", enable_metric_only),
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-top.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-top.c
@@ -807,7 +807,7 @@
 		 * invalid --vmlinux ;-)
 		 */
 		if (!machine->kptr_restrict_warned && !top->vmlinux_warned &&
-		    __map__is_kernel(al.map) && map__has_symbols(al.map)) {
+		    __map__is_kernel(al.map) && !map__has_symbols(al.map)) {
 			if (symbol_conf.vmlinux_name) {
 				char serr[256];
 				dso__strerror_load(al.map->dso, serr, sizeof(serr));
@@ -1743,6 +1743,7 @@
 	top.session = perf_session__new(NULL, NULL);
 	if (IS_ERR(top.session)) {
 		status = PTR_ERR(top.session);
+		top.session = NULL;
 		goto out_delete_evlist;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/builtin-trace.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/builtin-trace.c
@@ -17,7 +17,9 @@
 #include "util/record.h"
 #include <traceevent/event-parse.h>
 #include <api/fs/tracing_path.h>
+#ifdef HAVE_LIBBPF_SUPPORT
 #include <bpf/bpf.h>
+#endif
 #include "util/bpf_map.h"
 #include "util/rlimit.h"
 #include "builtin.h"
@@ -87,6 +89,8 @@
 # define F_LINUX_SPECIFIC_BASE	1024
 #endif
 
+#define RAW_SYSCALL_ARGS_NUM	6
+
 /*
  * strtoul: Go from a string to a value, i.e. for msr: MSR_FS_BASE to 0xc0000100
  */
@@ -107,7 +111,7 @@
 		const char *sys_enter,
 			   *sys_exit;
 	}	   bpf_prog_name;
-	struct syscall_arg_fmt arg[6];
+	struct syscall_arg_fmt arg[RAW_SYSCALL_ARGS_NUM];
 	u8	   nr_args;
 	bool	   errpid;
 	bool	   timeout;
@@ -1224,7 +1228,7 @@
  */
 struct bpf_map_syscall_entry {
 	bool	enabled;
-	u16	string_args_len[6];
+	u16	string_args_len[RAW_SYSCALL_ARGS_NUM];
 };
 
 /*
@@ -1649,7 +1653,7 @@
 {
 	int idx;
 
-	if (nr_args == 6 && sc->fmt && sc->fmt->nr_args != 0)
+	if (nr_args == RAW_SYSCALL_ARGS_NUM && sc->fmt && sc->fmt->nr_args != 0)
 		nr_args = sc->fmt->nr_args;
 
 	sc->arg_fmt = calloc(nr_args, sizeof(*sc->arg_fmt));
@@ -1782,11 +1786,11 @@
 #endif
 	sc = trace->syscalls.table + id;
 	if (sc->nonexistent)
-		return 0;
+		return -EEXIST;
 
 	if (name == NULL) {
 		sc->nonexistent = true;
-		return 0;
+		return -EEXIST;
 	}
 
 	sc->name = name;
@@ -1800,11 +1804,22 @@
 		sc->tp_format = trace_event__tp_format("syscalls", tp_name);
 	}
 
-	if (syscall__alloc_arg_fmts(sc, IS_ERR(sc->tp_format) ? 6 : sc->tp_format->format.nr_fields))
-		return -ENOMEM;
-
-	if (IS_ERR(sc->tp_format))
+	/*
+	 * Fails to read trace point format via sysfs node, so the trace point
+	 * doesn't exist.  Set the 'nonexistent' flag as true.
+	 */
+	if (IS_ERR(sc->tp_format)) {
+		sc->nonexistent = true;
 		return PTR_ERR(sc->tp_format);
+	}
+
+	/*
+	 * The tracepoint format contains __syscall_nr field, so it's one more
+	 * than the actual number of syscall arguments.
+	 */
+	if (syscall__alloc_arg_fmts(sc, IS_ERR(sc->tp_format) ?
+					RAW_SYSCALL_ARGS_NUM : sc->tp_format->format.nr_fields - 1))
+		return -ENOMEM;
 
 	sc->args = sc->tp_format->format.fields;
 	/*
@@ -2122,11 +2137,8 @@
 	    (err = trace__read_syscall_info(trace, id)) != 0)
 		goto out_cant_read;
 
-	if (trace->syscalls.table[id].name == NULL) {
-		if (trace->syscalls.table[id].nonexistent)
-			return NULL;
+	if (trace->syscalls.table && trace->syscalls.table[id].nonexistent)
 		goto out_cant_read;
-	}
 
 	return &trace->syscalls.table[id];
 
@@ -2279,7 +2291,7 @@
 	if (!sc)
 		return;
 
-	free(sc->arg_fmt);
+	zfree(&sc->arg_fmt);
 }
 
 static int trace__sys_enter(struct trace *trace, struct evsel *evsel,
@@ -2371,6 +2383,7 @@
 	char msg[1024];
 	void *args, *augmented_args = NULL;
 	int augmented_args_size;
+	size_t printed = 0;
 
 	if (sc == NULL)
 		return -1;
@@ -2386,8 +2399,8 @@
 
 	args = perf_evsel__sc_tp_ptr(evsel, args, sample);
 	augmented_args = syscall__augmented_args(sc, sample, &augmented_args_size, trace->raw_augmented_syscalls_args_size);
-	syscall__scnprintf_args(sc, msg, sizeof(msg), args, augmented_args, augmented_args_size, trace, thread);
-	fprintf(trace->output, "%s", msg);
+	printed += syscall__scnprintf_args(sc, msg, sizeof(msg), args, augmented_args, augmented_args_size, trace, thread);
+	fprintf(trace->output, "%.*s", (int)printed, msg);
 	err = 0;
 out_put:
 	thread__put(thread);
@@ -2758,7 +2771,7 @@
 		printed += syscall_arg_fmt__scnprintf_val(arg, bf + printed, size - printed, &syscall_arg, val);
 	}
 
-	return printed + fprintf(trace->output, "%s", bf);
+	return printed + fprintf(trace->output, "%.*s", (int)printed, bf);
 }
 
 static int trace__event_handler(struct trace *trace, struct evsel *evsel,
@@ -2767,13 +2780,8 @@
 {
 	struct thread *thread;
 	int callchain_ret = 0;
-	/*
-	 * Check if we called perf_evsel__disable(evsel) due to, for instance,
-	 * this event's max_events having been hit and this is an entry coming
-	 * from the ring buffer that we should discard, since the max events
-	 * have already been considered/printed.
-	 */
-	if (evsel->disabled)
+
+	if (evsel->nr_events_printed >= evsel->max_events)
 		return 0;
 
 	thread = machine__findnew_thread(trace->host, sample->pid, sample->tid);
@@ -3116,13 +3124,8 @@
 	struct evsel *evsel;
 
 	evlist__for_each_entry(evlist, evsel) {
-		struct evsel_trace *et = evsel->priv;
-
-		if (!et || !evsel->tp_format || strcmp(evsel->tp_format->system, "syscalls"))
-			continue;
-
-		free(et->fmt);
-		free(et);
+		evsel_trace__delete(evsel->priv);
+		evsel->priv = NULL;
 	}
 }
 
@@ -4740,11 +4743,11 @@
 	int i;
 
 	strlist__delete(trace->ev_qualifier);
-	free(trace->ev_qualifier_ids.entries);
+	zfree(&trace->ev_qualifier_ids.entries);
 	if (trace->syscalls.table) {
 		for (i = 0; i <= trace->sctbl->syscalls.max_id; i++)
 			syscall__exit(&trace->syscalls.table[i]);
-		free(trace->syscalls.table);
+		zfree(&trace->syscalls.table);
 	}
 	syscalltbl__delete(trace->sctbl);
 	zfree(&trace->perfconfig_events);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/perf-completion.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/perf-completion.sh
@@ -165,7 +165,12 @@
 
 		local cur1=${COMP_WORDS[COMP_CWORD]}
 		local raw_evts=$($cmd list --raw-dump)
-		local arr s tmp result
+		local arr s tmp result cpu_evts
+
+		# aarch64 doesn't have /sys/bus/event_source/devices/cpu/events
+		if [[ `uname -m` != aarch64 ]]; then
+			cpu_evts=$(ls /sys/bus/event_source/devices/cpu/events)
+		fi
 
 		if [[ "$cur1" == */* && ${cur1#*/} =~ ^[A-Z] ]]; then
 			OLD_IFS="$IFS"
@@ -183,9 +188,9 @@
 				fi
 			done
 
-			evts=${result}" "$(ls /sys/bus/event_source/devices/cpu/events)
+			evts=${result}" "${cpu_evts}
 		else
-			evts=${raw_evts}" "$(ls /sys/bus/event_source/devices/cpu/events)
+			evts=${raw_evts}" "${cpu_evts}
 		fi
 
 		if [[ "$cur1" == , ]]; then
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/perf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/perf.c
@@ -434,7 +434,7 @@
 static int libperf_print(enum libperf_print_level level,
 			 const char *fmt, va_list ap)
 {
-	return eprintf(level, verbose, fmt, ap);
+	return veprintf(level, verbose, fmt, ap);
 }
 
 int main(int argc, const char **argv)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/arm64/hisilicon/hip08/metrics.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/arm64/hisilicon/hip08/metrics.json
@@ -112,21 +112,21 @@
         "MetricName": "indirect_branch"
     },
     {
-        "MetricExpr": "(armv8_pmuv3_0@event\\=0x1014@ + armv8_pmuv3_0@event\\=0x1018@) / BR_MIS_PRED",
+        "MetricExpr": "(armv8_pmuv3_0@event\\=0x1013@ + armv8_pmuv3_0@event\\=0x1016@) / BR_MIS_PRED",
         "PublicDescription": "Push branch L3 topdown metric",
         "BriefDescription": "Push branch L3 topdown metric",
         "MetricGroup": "TopDownL3",
         "MetricName": "push_branch"
     },
     {
-        "MetricExpr": "armv8_pmuv3_0@event\\=0x100c@ / BR_MIS_PRED",
+        "MetricExpr": "armv8_pmuv3_0@event\\=0x100d@ / BR_MIS_PRED",
         "PublicDescription": "Pop branch L3 topdown metric",
         "BriefDescription": "Pop branch L3 topdown metric",
         "MetricGroup": "TopDownL3",
         "MetricName": "pop_branch"
     },
     {
-        "MetricExpr": "(BR_MIS_PRED - armv8_pmuv3_0@event\\=0x1010@ - armv8_pmuv3_0@event\\=0x1014@ - armv8_pmuv3_0@event\\=0x1018@ - armv8_pmuv3_0@event\\=0x100c@) / BR_MIS_PRED",
+        "MetricExpr": "(BR_MIS_PRED - armv8_pmuv3_0@event\\=0x1010@ - armv8_pmuv3_0@event\\=0x1013@ - armv8_pmuv3_0@event\\=0x1016@ - armv8_pmuv3_0@event\\=0x100d@) / BR_MIS_PRED",
         "PublicDescription": "Other branch L3 topdown metric",
         "BriefDescription": "Other branch L3 topdown metric",
         "MetricGroup": "TopDownL3",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/cache.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/cache.json
@@ -17,7 +17,7 @@
   {
     "EventCode": "0x34056",
     "EventName": "PM_EXEC_STALL_LOAD_FINISH",
-    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was finishing a load after its data was reloaded from a data source beyond the local L1; cycles in which the LSU was processing an L1-hit; cycles in which the NTF instruction merged with another load in the LMQ; cycles in which the NTF instruction is waiting for a data reload for a load miss, but the data comes back with a non-NTF instruction."
+    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was finishing a load after its data was reloaded from a data source beyond the local L1; cycles in which the LSU was processing an L1-hit; cycles in which the next-to-finish (NTF) instruction merged with another load in the LMQ; cycles in which the NTF instruction is waiting for a data reload for a load miss, but the data comes back with a non-NTF instruction."
   },
   {
     "EventCode": "0x3006C",
@@ -27,7 +27,7 @@
   {
     "EventCode": "0x300F4",
     "EventName": "PM_RUN_INST_CMPL_CONC",
-    "BriefDescription": "PowerPC instructions completed by this thread when all threads in the core had the run-latch set."
+    "BriefDescription": "PowerPC instruction completed by this thread when all threads in the core had the run-latch set."
   },
   {
     "EventCode": "0x4C016",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/frontend.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/frontend.json
@@ -7,7 +7,7 @@
   {
     "EventCode": "0x10006",
     "EventName": "PM_DISP_STALL_HELD_OTHER_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch for any other reason."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch for any other reason."
   },
   {
     "EventCode": "0x10010",
@@ -32,12 +32,12 @@
   {
     "EventCode": "0x1D05E",
     "EventName": "PM_DISP_STALL_HELD_HALT_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch because of power management."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch because of power management."
   },
   {
     "EventCode": "0x1E050",
     "EventName": "PM_DISP_STALL_HELD_STF_MAPPER_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch because the STF mapper/SRB was full. Includes GPR (count, link, tar), VSR, VMR, FPR."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch because the STF mapper/SRB was full. Includes GPR (count, link, tar), VSR, VMR, FPR."
   },
   {
     "EventCode": "0x1F054",
@@ -67,7 +67,7 @@
   {
     "EventCode": "0x100F6",
     "EventName": "PM_IERAT_MISS",
-    "BriefDescription": "IERAT Reloaded to satisfy an IERAT miss. All page sizes are counted by this event."
+    "BriefDescription": "IERAT Reloaded to satisfy an IERAT miss. All page sizes are counted by this event. This event only counts instruction demand access."
   },
   {
     "EventCode": "0x100F8",
@@ -77,7 +77,7 @@
   {
     "EventCode": "0x20006",
     "EventName": "PM_DISP_STALL_HELD_ISSQ_FULL_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch due to Issue queue full. Includes issue queue and branch queue."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch due to Issue queue full. Includes issue queue and branch queue."
   },
   {
     "EventCode": "0x20114",
@@ -102,7 +102,7 @@
   {
     "EventCode": "0x2D01A",
     "EventName": "PM_DISP_STALL_IC_MISS",
-    "BriefDescription": "Cycles when dispatch was stalled for this thread due to an Icache Miss."
+    "BriefDescription": "Cycles when dispatch was stalled for this thread due to an instruction cache miss."
   },
   {
     "EventCode": "0x2E018",
@@ -112,7 +112,7 @@
   {
     "EventCode": "0x2E01A",
     "EventName": "PM_DISP_STALL_HELD_XVFC_MAPPER_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch because the XVFC mapper/SRB was full."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch because the XVFC mapper/SRB was full."
   },
   {
     "EventCode": "0x2C142",
@@ -137,7 +137,7 @@
   {
     "EventCode": "0x30004",
     "EventName": "PM_DISP_STALL_FLUSH",
-    "BriefDescription": "Cycles when dispatch was stalled because of a flush that happened to an instruction(s) that was not yet NTC. PM_EXEC_STALL_NTC_FLUSH only includes instructions that were flushed after becoming NTC."
+    "BriefDescription": "Cycles when dispatch was stalled because of a flush that happened to an instruction(s) that was not yet next-to-complete (NTC). PM_EXEC_STALL_NTC_FLUSH only includes instructions that were flushed after becoming NTC."
   },
   {
     "EventCode": "0x3000A",
@@ -157,7 +157,7 @@
   {
     "EventCode": "0x30018",
     "EventName": "PM_DISP_STALL_HELD_SCOREBOARD_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch while waiting on the Scoreboard. This event combines VSCR and FPSCR together."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch while waiting on the Scoreboard. This event combines VSCR and FPSCR together."
   },
   {
     "EventCode": "0x30026",
@@ -182,7 +182,7 @@
   {
     "EventCode": "0x3D05C",
     "EventName": "PM_DISP_STALL_HELD_RENAME_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch because the mapper/SRB was full. Includes GPR (count, link, tar), VSR, VMR, FPR and XVFC."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch because the mapper/SRB was full. Includes GPR (count, link, tar), VSR, VMR, FPR and XVFC."
   },
   {
     "EventCode": "0x3E052",
@@ -192,7 +192,7 @@
   {
     "EventCode": "0x3E054",
     "EventName": "PM_LD_MISS_L1",
-    "BriefDescription": "Load Missed L1, counted at execution time (can be greater than loads finished). LMQ merges are not included in this count. i.e. if a load instruction misses on an address that is already allocated on the LMQ, this event will not increment for that load). Note that this count is per slice, so if a load spans multiple slices this event will increment multiple times for a single load."
+    "BriefDescription": "Load missed L1, counted at finish time. LMQ merges are not included in this count. i.e. if a load instruction misses on an address that is already allocated on the LMQ, this event will not increment for that load). Note that this count is per slice, so if a load spans multiple slices this event will increment multiple times for a single load."
   },
   {
     "EventCode": "0x301EA",
@@ -202,7 +202,7 @@
   {
     "EventCode": "0x300FA",
     "EventName": "PM_INST_FROM_L3MISS",
-    "BriefDescription": "The processor's instruction cache was reloaded from a source other than the local core's L1, L2, or L3 due to a demand miss."
+    "BriefDescription": "The processor's instruction cache was reloaded from beyond the local core's L3 due to a demand miss."
   },
   {
     "EventCode": "0x40006",
@@ -232,16 +232,16 @@
   {
     "EventCode": "0x4E01A",
     "EventName": "PM_DISP_STALL_HELD_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch for any reason."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch for any reason."
   },
   {
     "EventCode": "0x4003C",
     "EventName": "PM_DISP_STALL_HELD_SYNC_CYC",
-    "BriefDescription": "Cycles in which the NTC instruction is held at dispatch because of a synchronizing instruction that requires the ICT to be empty before dispatch."
+    "BriefDescription": "Cycles in which the next-to-complete (NTC) instruction is held at dispatch because of a synchronizing instruction that requires the ICT to be empty before dispatch."
   },
   {
     "EventCode": "0x44056",
     "EventName": "PM_VECTOR_ST_CMPL",
-    "BriefDescription": "Vector store instructions completed."
+    "BriefDescription": "Vector store instruction completed."
   }
 ]
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/marked.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/marked.json
@@ -20,11 +20,6 @@
     "BriefDescription": "Marked Branch Taken instruction completed."
   },
   {
-    "EventCode": "0x20112",
-    "EventName": "PM_MRK_NTF_FIN",
-    "BriefDescription": "The marked instruction became the oldest in the pipeline before it finished. It excludes instructions that finish at dispatch."
-  },
-  {
     "EventCode": "0x2C01C",
     "EventName": "PM_EXEC_STALL_DMISS_OFF_CHIP",
     "BriefDescription": "Cycles in which the oldest instruction in the pipeline was waiting for a load miss to resolve from a remote chip."
@@ -62,17 +57,12 @@
   {
     "EventCode": "0x200FD",
     "EventName": "PM_L1_ICACHE_MISS",
-    "BriefDescription": "Demand iCache Miss."
-  },
-  {
-    "EventCode": "0x30130",
-    "EventName": "PM_MRK_INST_FIN",
-    "BriefDescription": "marked instruction finished. Excludes instructions that finish at dispatch. Note that stores always finish twice since the address gets issued to the LSU and the data gets issued to the VSU."
+    "BriefDescription": "Demand instruction cache miss."
   },
   {
     "EventCode": "0x34146",
     "EventName": "PM_MRK_LD_CMPL",
-    "BriefDescription": "Marked loads completed."
+    "BriefDescription": "Marked load instruction completed."
   },
   {
     "EventCode": "0x3E158",
@@ -82,12 +72,12 @@
   {
     "EventCode": "0x3E15A",
     "EventName": "PM_MRK_ST_FIN",
-    "BriefDescription": "The marked instruction was a store of any kind."
+    "BriefDescription": "Marked store instruction finished."
   },
   {
     "EventCode": "0x30068",
     "EventName": "PM_L1_ICACHE_RELOADED_PREF",
-    "BriefDescription": "Counts all Icache prefetch reloads ( includes demand turned into prefetch)."
+    "BriefDescription": "Counts all instruction cache prefetch reloads (includes demand turned into prefetch)."
   },
   {
     "EventCode": "0x301E4",
@@ -102,12 +92,12 @@
   {
     "EventCode": "0x300FE",
     "EventName": "PM_DATA_FROM_L3MISS",
-    "BriefDescription": "The processor's data cache was reloaded from a source other than the local core's L1, L2, or L3 due to a demand miss."
+    "BriefDescription": "The processor's L1 data cache was reloaded from beyond the local core's L3 due to a demand miss."
   },
   {
     "EventCode": "0x40012",
     "EventName": "PM_L1_ICACHE_RELOADED_ALL",
-    "BriefDescription": "Counts all Icache reloads includes demand, prefetch, prefetch turned into demand and demand turned into prefetch."
+    "BriefDescription": "Counts all instruction cache reloads includes demand, prefetch, prefetch turned into demand and demand turned into prefetch."
   },
   {
     "EventCode": "0x40134",
@@ -117,22 +107,22 @@
   {
     "EventCode": "0x4505A",
     "EventName": "PM_SP_FLOP_CMPL",
-    "BriefDescription": "Single Precision floating point instructions completed."
+    "BriefDescription": "Single Precision floating point instruction completed."
   },
   {
     "EventCode": "0x4D058",
     "EventName": "PM_VECTOR_FLOP_CMPL",
-    "BriefDescription": "Vector floating point instructions completed."
+    "BriefDescription": "Vector floating point instruction completed."
   },
   {
     "EventCode": "0x4D05A",
     "EventName": "PM_NON_MATH_FLOP_CMPL",
-    "BriefDescription": "Non Math instructions completed."
+    "BriefDescription": "Non Math instruction completed."
   },
   {
     "EventCode": "0x401E0",
     "EventName": "PM_MRK_INST_CMPL",
-    "BriefDescription": "marked instruction completed."
+    "BriefDescription": "Marked instruction completed."
   },
   {
     "EventCode": "0x400FE",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/memory.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/memory.json
@@ -47,7 +47,7 @@
   {
     "EventCode": "0x10062",
     "EventName": "PM_LD_L3MISS_PEND_CYC",
-    "BriefDescription": "Cycles L3 miss was pending for this thread."
+    "BriefDescription": "Cycles in which an L3 miss was pending for this thread."
   },
   {
     "EventCode": "0x20010",
@@ -132,7 +132,7 @@
   {
     "EventCode": "0x300FC",
     "EventName": "PM_DTLB_MISS",
-    "BriefDescription": "The DPTEG required for the load/store instruction in execution was missing from the TLB. It includes pages of all sizes for demand and prefetch activity."
+    "BriefDescription": "The DPTEG required for the load/store instruction in execution was missing from the TLB. This event only counts for demand misses."
   },
   {
     "EventCode": "0x4D02C",
@@ -142,7 +142,7 @@
   {
     "EventCode": "0x4003E",
     "EventName": "PM_LD_CMPL",
-    "BriefDescription": "Loads completed."
+    "BriefDescription": "Load instruction completed."
   },
   {
     "EventCode": "0x4C040",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/nest_metrics.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/nest_metrics.json
@@ -1,13 +1,13 @@
 [
     {
       "MetricName": "VEC_GROUP_PUMP_RETRY_RATIO_P01",
-      "MetricExpr": "(hv_24x7@PM_PB_RTY_VG_PUMP01\\,chip\\=?@ / hv_24x7@PM_PB_VG_PUMP01\\,chip\\=?@) * 100",
+      "MetricExpr": "(hv_24x7@PM_PB_RTY_VG_PUMP01\\,chip\\=?@ / (1 + hv_24x7@PM_PB_VG_PUMP01\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "VEC_GROUP_PUMP_RETRY_RATIO_P23",
-      "MetricExpr": "(hv_24x7@PM_PB_RTY_VG_PUMP23\\,chip\\=?@ / hv_24x7@PM_PB_VG_PUMP23\\,chip\\=?@) * 100",
+      "MetricExpr": "(hv_24x7@PM_PB_RTY_VG_PUMP23\\,chip\\=?@ / (1 + hv_24x7@PM_PB_VG_PUMP23\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
@@ -61,13 +61,13 @@
     },
     {
       "MetricName": "REMOTE_NODE_PUMPS_RETRIES_RATIO_P01",
-      "MetricExpr": "(hv_24x7@PM_PB_RTY_RNS_PUMP01\\,chip\\=?@ / hv_24x7@PM_PB_RNS_PUMP01\\,chip\\=?@) * 100",
+      "MetricExpr": "(hv_24x7@PM_PB_RTY_RNS_PUMP01\\,chip\\=?@ / (1 + hv_24x7@PM_PB_RNS_PUMP01\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "REMOTE_NODE_PUMPS_RETRIES_RATIO_P23",
-      "MetricExpr": "(hv_24x7@PM_PB_RTY_RNS_PUMP23\\,chip\\=?@ / hv_24x7@PM_PB_RNS_PUMP23\\,chip\\=?@) * 100",
+      "MetricExpr": "(hv_24x7@PM_PB_RTY_RNS_PUMP23\\,chip\\=?@ / (1 + hv_24x7@PM_PB_RNS_PUMP23\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
@@ -151,193 +151,193 @@
     },
     {
       "MetricName": "XLINK0_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK0_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK0_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK1_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK1_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK1_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK2_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK2_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK2_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK3_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK3_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK3_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK4_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK4_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK4_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK5_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK5_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK5_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK6_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK6_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK6_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK7_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK7_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_XLINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK7_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK0_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK0_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK0_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK1_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK1_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK1_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK2_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK2_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK2_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK3_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK3_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK3_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK4_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK4_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK4_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK5_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK5_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK5_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK6_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK6_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK6_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "XLINK7_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_XLINK7_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_XLINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_XLINK7_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_XLINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_XLINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK0_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK0_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK0_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK1_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK1_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK1_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK2_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK2_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK2_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK3_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK3_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK3_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK4_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK4_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK4_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK5_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK5_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK5_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK6_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK6_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK6_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK7_OUT_TOTAL_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK7_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (hv_24x7@PM_ALINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK7_OUT_ODD_TOTAL_UTIL\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_TOTAL_UTIL\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK0_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK0_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK0_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK0_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK0_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK1_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK1_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK1_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK1_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK1_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK2_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK2_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK2_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK2_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK2_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK3_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK3_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK3_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK3_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK3_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK4_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK4_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK4_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK4_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK4_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK5_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK5_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK5_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK5_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK5_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK6_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK6_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK6_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK6_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK6_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
     {
       "MetricName": "ALINK7_OUT_DATA_UTILIZATION",
-      "MetricExpr": "((hv_24x7@PM_ALINK7_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_DATA\\,chip\\=?@) / (hv_24x7@PM_ALINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
+      "MetricExpr": "((hv_24x7@PM_ALINK7_OUT_ODD_DATA\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_DATA\\,chip\\=?@) / (1 + hv_24x7@PM_ALINK7_OUT_ODD_AVLBL_CYCLES\\,chip\\=?@ + hv_24x7@PM_ALINK7_OUT_EVEN_AVLBL_CYCLES\\,chip\\=?@)) * 100",
       "ScaleUnit": "1.063%",
       "AggregationMode": "PerChip"
     },
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/others.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/others.json
@@ -2,12 +2,12 @@
   {
     "EventCode": "0x10016",
     "EventName": "PM_VSU0_ISSUE",
-    "BriefDescription": "VSU instructions issued to VSU pipe 0."
+    "BriefDescription": "VSU instruction issued to VSU pipe 0."
   },
   {
     "EventCode": "0x1001C",
     "EventName": "PM_ULTRAVISOR_INST_CMPL",
-    "BriefDescription": "PowerPC instructions that completed while the thread was in ultravisor state."
+    "BriefDescription": "PowerPC instruction completed while the thread was in ultravisor state."
   },
   {
     "EventCode": "0x100F0",
@@ -17,12 +17,12 @@
   {
     "EventCode": "0x10134",
     "EventName": "PM_MRK_ST_DONE_L2",
-    "BriefDescription": "Marked stores completed in L2 (RC machine done)."
+    "BriefDescription": "Marked store completed in L2."
   },
   {
     "EventCode": "0x1505E",
     "EventName": "PM_LD_HIT_L1",
-    "BriefDescription": "Loads that finished without experiencing an L1 miss."
+    "BriefDescription": "Load finished without experiencing an L1 miss."
   },
   {
     "EventCode": "0x1F056",
@@ -30,11 +30,6 @@
     "BriefDescription": "Cycles in which Superslice 0 dispatches either 1 or 2 instructions."
   },
   {
-    "EventCode": "0x1F15C",
-    "EventName": "PM_MRK_STCX_L2_CYC",
-    "BriefDescription": "Cycles spent in the nest portion of a marked Stcx instruction. It starts counting when the operation starts to drain to the L2 and it stops counting when the instruction retires from the Instruction Completion Table (ICT) in the Instruction Sequencing Unit (ISU)."
-  },
-  {
     "EventCode": "0x10066",
     "EventName": "PM_ADJUNCT_CYC",
     "BriefDescription": "Cycles in which the thread is in Adjunct state. MSR[S HV PR] bits = 011."
@@ -42,7 +37,7 @@
   {
     "EventCode": "0x101E4",
     "EventName": "PM_MRK_L1_ICACHE_MISS",
-    "BriefDescription": "Marked Instruction suffered an icache Miss."
+    "BriefDescription": "Marked instruction suffered an instruction cache miss."
   },
   {
     "EventCode": "0x101EA",
@@ -72,7 +67,7 @@
   {
     "EventCode": "0x2E010",
     "EventName": "PM_ADJUNCT_INST_CMPL",
-    "BriefDescription": "PowerPC instructions that completed while the thread is in Adjunct state."
+    "BriefDescription": "PowerPC instruction completed while the thread was in Adjunct state."
   },
   {
     "EventCode": "0x2E014",
@@ -122,7 +117,7 @@
   {
     "EventCode": "0x201E4",
     "EventName": "PM_MRK_DATA_FROM_L3MISS",
-    "BriefDescription": "The processor's data cache was reloaded from a source other than the local core's L1, L2, or L3 due to a demand miss for a marked load."
+    "BriefDescription": "The processor's L1 data cache was reloaded from beyond the local core's L3 due to a demand miss for a marked instruction."
   },
   {
     "EventCode": "0x201E8",
@@ -132,17 +127,17 @@
   {
     "EventCode": "0x200F2",
     "EventName": "PM_INST_DISP",
-    "BriefDescription": "PowerPC instructions dispatched."
+    "BriefDescription": "PowerPC instruction dispatched."
   },
   {
     "EventCode": "0x30132",
     "EventName": "PM_MRK_VSU_FIN",
-    "BriefDescription": "VSU marked instructions finished. Excludes simple FX instructions issued to the Store Unit."
+    "BriefDescription": "VSU marked instruction finished. Excludes simple FX instructions issued to the Store Unit."
   },
   {
     "EventCode": "0x30038",
     "EventName": "PM_EXEC_STALL_DMISS_LMEM",
-    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was waiting for a load miss to resolve from the local memory, local OpenCapp cache, or local OpenCapp memory."
+    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was waiting for a load miss to resolve from the local memory, local OpenCAPI cache, or local OpenCAPI memory."
   },
   {
     "EventCode": "0x3F04A",
@@ -152,12 +147,12 @@
   {
     "EventCode": "0x3405A",
     "EventName": "PM_PRIVILEGED_INST_CMPL",
-    "BriefDescription": "PowerPC Instructions that completed while the thread is in Privileged state."
+    "BriefDescription": "PowerPC instruction completed while the thread was in Privileged state."
   },
   {
     "EventCode": "0x3F150",
     "EventName": "PM_MRK_ST_DRAIN_CYC",
-    "BriefDescription": "cycles to drain st from core to L2."
+    "BriefDescription": "Cycles in which the marked store drained from the core to the L2."
   },
   {
     "EventCode": "0x3F054",
@@ -182,7 +177,7 @@
   {
     "EventCode": "0x4001C",
     "EventName": "PM_VSU_FIN",
-    "BriefDescription": "VSU instructions finished."
+    "BriefDescription": "VSU instruction finished."
   },
   {
     "EventCode": "0x4C01A",
@@ -197,7 +192,7 @@
   {
     "EventCode": "0x4D022",
     "EventName": "PM_HYPERVISOR_INST_CMPL",
-    "BriefDescription": "PowerPC instructions that completed while the thread is in hypervisor state."
+    "BriefDescription": "PowerPC instruction completed while the thread was in hypervisor state."
   },
   {
     "EventCode": "0x4D026",
@@ -212,32 +207,32 @@
   {
     "EventCode": "0x40030",
     "EventName": "PM_INST_FIN",
-    "BriefDescription": "Instructions finished."
+    "BriefDescription": "Instruction finished."
   },
   {
     "EventCode": "0x44146",
     "EventName": "PM_MRK_STCX_CORE_CYC",
-    "BriefDescription": "Cycles spent in the core portion of a marked Stcx instruction. It starts counting when the instruction is decoded and stops counting when it drains into the L2."
+    "BriefDescription": "Cycles spent in the core portion of a marked STCX instruction. It starts counting when the instruction is decoded and stops counting when it drains into the L2."
   },
   {
     "EventCode": "0x44054",
     "EventName": "PM_VECTOR_LD_CMPL",
-    "BriefDescription": "Vector load instructions completed."
+    "BriefDescription": "Vector load instruction completed."
   },
   {
     "EventCode": "0x45054",
     "EventName": "PM_FMA_CMPL",
-    "BriefDescription": "Two floating point instructions completed (FMA class of instructions: fmadd, fnmadd, fmsub, fnmsub). Scalar instructions only."
+    "BriefDescription": "Two floating point instruction completed (FMA class of instructions: fmadd, fnmadd, fmsub, fnmsub). Scalar instructions only."
   },
   {
     "EventCode": "0x45056",
     "EventName": "PM_SCALAR_FLOP_CMPL",
-    "BriefDescription": "Scalar floating point instructions completed."
+    "BriefDescription": "Scalar floating point instruction completed."
   },
   {
     "EventCode": "0x4505C",
     "EventName": "PM_MATH_FLOP_CMPL",
-    "BriefDescription": "Math floating point instructions completed."
+    "BriefDescription": "Math floating point instruction completed."
   },
   {
     "EventCode": "0x4D05E",
@@ -252,21 +247,21 @@
   {
     "EventCode": "0x401E6",
     "EventName": "PM_MRK_INST_FROM_L3MISS",
-    "BriefDescription": "The processor's instruction cache was reloaded from a source other than the local core's L1, L2, or L3 due to a demand miss for a marked instruction."
+    "BriefDescription": "The processor's instruction cache was reloaded from beyond the local core's L3 due to a demand miss for a marked instruction."
   },
   {
     "EventCode": "0x401E8",
     "EventName": "PM_MRK_DATA_FROM_L2MISS",
-    "BriefDescription": "The processor's data cache was reloaded from a source other than the local core's L1 or L2 due to a demand miss for a marked load."
+    "BriefDescription": "The processor's L1 data cache was reloaded from a source beyond the local core's L2 due to a demand miss for a marked instruction."
   },
   {
     "EventCode": "0x400F0",
     "EventName": "PM_LD_DEMAND_MISS_L1_FIN",
-    "BriefDescription": "Load Missed L1, counted at finish time."
+    "BriefDescription": "Load missed L1, counted at finish time."
   },
   {
     "EventCode": "0x400FA",
     "EventName": "PM_RUN_INST_CMPL",
-    "BriefDescription": "Completed PowerPC instructions gated by the run latch."
+    "BriefDescription": "PowerPC instruction completed while the run latch is set."
   }
 ]
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/pipeline.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/pipeline.json
@@ -2,7 +2,7 @@
   {
     "EventCode": "0x100FE",
     "EventName": "PM_INST_CMPL",
-    "BriefDescription": "PowerPC instructions completed."
+    "BriefDescription": "PowerPC instruction completed."
   },
   {
     "EventCode": "0x1000C",
@@ -12,7 +12,7 @@
   {
     "EventCode": "0x1000E",
     "EventName": "PM_MMA_ISSUED",
-    "BriefDescription": "MMA instructions issued."
+    "BriefDescription": "MMA instruction issued."
   },
   {
     "EventCode": "0x10012",
@@ -107,7 +107,7 @@
   {
     "EventCode": "0x2D012",
     "EventName": "PM_VSU1_ISSUE",
-    "BriefDescription": "VSU instructions issued to VSU pipe 1."
+    "BriefDescription": "VSU instruction issued to VSU pipe 1."
   },
   {
     "EventCode": "0x2D018",
@@ -122,7 +122,7 @@
   {
     "EventCode": "0x2E01E",
     "EventName": "PM_EXEC_STALL_NTC_FLUSH",
-    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was executing in any unit before it was flushed. Note that if the flush of the oldest instruction happens after finish, the cycles from dispatch to issue will be included in PM_DISP_STALL and the cycles from issue to finish will be included in PM_EXEC_STALL and its corresponding children. This event will also count cycles when the previous NTF instruction is still completing and the new NTF instruction is stalled at dispatch."
+    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was executing in any unit before it was flushed. Note that if the flush of the oldest instruction happens after finish, the cycles from dispatch to issue will be included in PM_DISP_STALL and the cycles from issue to finish will be included in PM_EXEC_STALL and its corresponding children. This event will also count cycles when the previous next-to-finish (NTF) instruction is still completing and the new NTF instruction is stalled at dispatch."
   },
   {
     "EventCode": "0x2013C",
@@ -137,7 +137,7 @@
   {
     "EventCode": "0x201E2",
     "EventName": "PM_MRK_LD_MISS_L1",
-    "BriefDescription": "Marked DL1 Demand Miss counted at finish time."
+    "BriefDescription": "Marked demand data load miss counted at finish time."
   },
   {
     "EventCode": "0x200F4",
@@ -172,7 +172,7 @@
   {
     "EventCode": "0x30028",
     "EventName": "PM_CMPL_STALL_MEM_ECC",
-    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was waiting for the non-speculative finish of either a stcx waiting for its result or a load waiting for non-critical sectors of data and ECC."
+    "BriefDescription": "Cycles in which the oldest instruction in the pipeline was waiting for the non-speculative finish of either a STCX waiting for its result or a load waiting for non-critical sectors of data and ECC."
   },
   {
     "EventCode": "0x30036",
@@ -187,17 +187,12 @@
   {
     "EventCode": "0x3F044",
     "EventName": "PM_VSU2_ISSUE",
-    "BriefDescription": "VSU instructions issued to VSU pipe 2."
+    "BriefDescription": "VSU instruction issued to VSU pipe 2."
   },
   {
     "EventCode": "0x30058",
     "EventName": "PM_TLBIE_FIN",
-    "BriefDescription": "TLBIE instructions finished in the LSU. Two TLBIEs can finish each cycle. All will be counted."
-  },
-  {
-    "EventCode": "0x3D058",
-    "EventName": "PM_SCALAR_FSQRT_FDIV_ISSUE",
-    "BriefDescription": "Scalar versions of four floating point operations: fdiv,fsqrt (xvdivdp, xvdivsp, xvsqrtdp, xvsqrtsp)."
+    "BriefDescription": "TLBIE instruction finished in the LSU. Two TLBIEs can finish each cycle. All will be counted."
   },
   {
     "EventCode": "0x30066",
@@ -252,7 +247,7 @@
   {
     "EventCode": "0x4E012",
     "EventName": "PM_EXEC_STALL_UNKNOWN",
-    "BriefDescription": "Cycles in which the oldest instruction in the pipeline completed without an ntf_type pulse. The ntf_pulse was missed by the ISU because the NTF finishes and completions came too close together."
+    "BriefDescription": "Cycles in which the oldest instruction in the pipeline completed without an ntf_type pulse. The ntf_pulse was missed by the ISU because the next-to-finish (NTF) instruction finishes and completions came too close together."
   },
   {
     "EventCode": "0x4D020",
@@ -267,12 +262,7 @@
   {
     "EventCode": "0x45058",
     "EventName": "PM_IC_MISS_CMPL",
-    "BriefDescription": "Non-speculative icache miss, counted at completion."
-  },
-  {
-    "EventCode": "0x4D050",
-    "EventName": "PM_VSU_NON_FLOP_CMPL",
-    "BriefDescription": "Non-floating point VSU instructions completed."
+    "BriefDescription": "Non-speculative instruction cache miss, counted at completion."
   },
   {
     "EventCode": "0x4D052",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/pmc.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/pmc.json
@@ -12,11 +12,11 @@
   {
     "EventCode": "0x45052",
     "EventName": "PM_4FLOP_CMPL",
-    "BriefDescription": "Four floating point instructions completed (fadd, fmul, fsub, fcmp, fsel, fabs, fnabs, fres, fsqrte, fneg)."
+    "BriefDescription": "Four floating point instruction completed (fadd, fmul, fsub, fcmp, fsel, fabs, fnabs, fres, fsqrte, fneg)."
   },
   {
     "EventCode": "0x4D054",
     "EventName": "PM_8FLOP_CMPL",
-    "BriefDescription": "Four Double Precision vector instructions completed."
+    "BriefDescription": "Four Double Precision vector instruction completed."
   }
 ]
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power10/translation.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power10/translation.json
@@ -5,11 +5,6 @@
     "BriefDescription": "Marked Start probe nop (AND R0,R0,R0) completed."
   },
   {
-    "EventCode": "0x20016",
-    "EventName": "PM_ST_FIN",
-    "BriefDescription": "Store finish count. Includes speculative activity."
-  },
-  {
     "EventCode": "0x20018",
     "EventName": "PM_ST_FWD",
     "BriefDescription": "Store forwards that finished."
@@ -17,7 +12,7 @@
   {
     "EventCode": "0x2011C",
     "EventName": "PM_MRK_NTF_CYC",
-    "BriefDescription": "Cycles during which the marked instruction is the oldest in the pipeline (NTF or NTC)."
+    "BriefDescription": "Cycles in which the marked instruction is the oldest in the pipeline (next-to-finish or next-to-complete)."
   },
   {
     "EventCode": "0x2E01C",
@@ -37,7 +32,7 @@
   {
     "EventCode": "0x200FE",
     "EventName": "PM_DATA_FROM_L2MISS",
-    "BriefDescription": "The processor's data cache was reloaded from a source other than the local core's L1 or L2 due to a demand miss."
+    "BriefDescription": "The processor's L1 data cache was reloaded from a source beyond the local core's L2 due to a demand miss."
   },
   {
     "EventCode": "0x30010",
@@ -52,6 +47,6 @@
   {
     "EventCode": "0x4D05C",
     "EventName": "PM_DPP_FLOP_CMPL",
-    "BriefDescription": "Double-Precision or Quad-Precision instructions completed."
+    "BriefDescription": "Double-Precision or Quad-Precision instruction completed."
   }
 ]
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power9/other.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power9/other.json
@@ -1417,7 +1417,7 @@
   {
     "EventCode": "0x45054",
     "EventName": "PM_FMA_CMPL",
-    "BriefDescription": "two flops operation completed (fmadd, fnmadd, fmsub, fnmsub) Scalar instructions only. "
+    "BriefDescription": "two flops operation completed (fmadd, fnmadd, fmsub, fnmsub) Scalar instructions only."
   },
   {
     "EventCode": "0x201E8",
@@ -2017,7 +2017,7 @@
   {
     "EventCode": "0xC0BC",
     "EventName": "PM_LSU_FLUSH_OTHER",
-    "BriefDescription": "Other LSU flushes including: Sync (sync ack from L2 caused search of LRQ for oldest snooped load, This will either signal a Precise Flush of the oldest snooped loa or a Flush Next PPC); Data Valid Flush Next (several cases of this, one example is store and reload are lined up such that a store-hit-reload scenario exists and the CDF has already launched and has gotten bad/stale data); Bad Data Valid Flush Next (might be a few cases of this, one example is a larxa (D$ hit) return data and dval but can't allocate to LMQ (LMQ full or other reason). Already gave dval but can't watch it for snoop_hit_larx. Need to take the “bad dval” back and flush all younger ops)"
+    "BriefDescription": "Other LSU flushes including: Sync (sync ack from L2 caused search of LRQ for oldest snooped load, This will either signal a Precise Flush of the oldest snooped loa or a Flush Next PPC); Data Valid Flush Next (several cases of this, one example is store and reload are lined up such that a store-hit-reload scenario exists and the CDF has already launched and has gotten bad/stale data); Bad Data Valid Flush Next (might be a few cases of this, one example is a larxa (D$ hit) return data and dval but can't allocate to LMQ (LMQ full or other reason). Already gave dval but can't watch it for snoop_hit_larx. Need to take the 'bad dval' back and flush all younger ops)"
   },
   {
     "EventCode": "0x5094",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/powerpc/power9/pipeline.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/powerpc/power9/pipeline.json
@@ -442,7 +442,7 @@
   {
     "EventCode": "0x4D052",
     "EventName": "PM_2FLOP_CMPL",
-    "BriefDescription": "DP vector version of fmul, fsub, fcmp, fsel, fabs, fnabs, fres ,fsqrte, fneg "
+    "BriefDescription": "DP vector version of fmul, fsub, fcmp, fsel, fabs, fnabs, fres ,fsqrte, fneg"
   },
   {
     "EventCode": "0x1F142",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/cache.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/cache.json
@@ -315,6 +315,19 @@
         "UMask": "0x82"
     },
     {
+        "BriefDescription": "All retired memory instructions.",
+        "Counter": "0,1,2,3",
+        "CounterHTOff": "0,1,2,3",
+        "Data_LA": "1",
+        "EventCode": "0xD0",
+        "EventName": "MEM_INST_RETIRED.ANY",
+        "L1_Hit_Indication": "1",
+        "PEBS": "1",
+        "PublicDescription": "Counts all retired memory instructions - loads and stores.",
+        "SampleAfterValue": "2000003",
+        "UMask": "0x83"
+    },
+    {
         "BriefDescription": "Retired load instructions with locked access.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3",
@@ -358,6 +371,7 @@
         "EventCode": "0xD0",
         "EventName": "MEM_INST_RETIRED.STLB_MISS_LOADS",
         "PEBS": "1",
+        "PublicDescription": "Number of retired load instructions that (start a) miss in the 2nd-level TLB (STLB).",
         "SampleAfterValue": "100003",
         "UMask": "0x11"
     },
@@ -370,6 +384,7 @@
         "EventName": "MEM_INST_RETIRED.STLB_MISS_STORES",
         "L1_Hit_Indication": "1",
         "PEBS": "1",
+        "PublicDescription": "Number of retired store instructions that (start a) miss in the 2nd-level TLB (STLB).",
         "SampleAfterValue": "100003",
         "UMask": "0x12"
     },
@@ -733,7 +748,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010491",
+        "MSRValue": "0x10491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -772,7 +787,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0491",
+        "MSRValue": "0x4003C0491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -785,7 +800,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0491",
+        "MSRValue": "0x1003C0491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -798,7 +813,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0491",
+        "MSRValue": "0x8003C0491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -811,7 +826,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010490",
+        "MSRValue": "0x10490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -850,7 +865,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0490",
+        "MSRValue": "0x4003C0490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -863,7 +878,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0490",
+        "MSRValue": "0x1003C0490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -876,7 +891,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0490",
+        "MSRValue": "0x8003C0490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -889,7 +904,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010120",
+        "MSRValue": "0x10120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -928,7 +943,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0120",
+        "MSRValue": "0x4003C0120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -941,7 +956,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0120",
+        "MSRValue": "0x1003C0120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -954,7 +969,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0120",
+        "MSRValue": "0x8003C0120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -967,7 +982,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010122",
+        "MSRValue": "0x10122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1006,7 +1021,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0122",
+        "MSRValue": "0x4003C0122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1019,7 +1034,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0122",
+        "MSRValue": "0x1003C0122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1032,7 +1047,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0122",
+        "MSRValue": "0x8003C0122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1045,7 +1060,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010004",
+        "MSRValue": "0x10004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1084,7 +1099,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0004",
+        "MSRValue": "0x4003C0004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1097,7 +1112,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0004",
+        "MSRValue": "0x1003C0004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1110,7 +1125,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0004",
+        "MSRValue": "0x8003C0004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1123,7 +1138,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010001",
+        "MSRValue": "0x10001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1162,7 +1177,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0001",
+        "MSRValue": "0x4003C0001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1175,7 +1190,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0001",
+        "MSRValue": "0x1003C0001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1188,7 +1203,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0001",
+        "MSRValue": "0x8003C0001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1201,7 +1216,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010002",
+        "MSRValue": "0x10002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1240,7 +1255,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0002",
+        "MSRValue": "0x4003C0002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1253,7 +1268,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0002",
+        "MSRValue": "0x1003C0002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1266,7 +1281,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0002",
+        "MSRValue": "0x8003C0002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1279,7 +1294,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010400",
+        "MSRValue": "0x10400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1318,7 +1333,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0400",
+        "MSRValue": "0x4003C0400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1331,7 +1346,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0400",
+        "MSRValue": "0x1003C0400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1344,7 +1359,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0400",
+        "MSRValue": "0x8003C0400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1357,7 +1372,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010010",
+        "MSRValue": "0x10010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1396,7 +1411,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0010",
+        "MSRValue": "0x4003C0010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1409,7 +1424,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0010",
+        "MSRValue": "0x1003C0010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1422,7 +1437,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0010",
+        "MSRValue": "0x8003C0010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1435,7 +1450,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010020",
+        "MSRValue": "0x10020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1474,7 +1489,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0020",
+        "MSRValue": "0x4003C0020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1487,7 +1502,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0020",
+        "MSRValue": "0x1003C0020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1500,7 +1515,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0020",
+        "MSRValue": "0x8003C0020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1513,7 +1528,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010080",
+        "MSRValue": "0x10080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1552,7 +1567,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0080",
+        "MSRValue": "0x4003C0080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1565,7 +1580,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0080",
+        "MSRValue": "0x1003C0080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1578,7 +1593,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0080",
+        "MSRValue": "0x8003C0080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1591,7 +1606,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.ANY_RESPONSE",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0000010100",
+        "MSRValue": "0x10100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1630,7 +1645,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_HIT.HIT_OTHER_CORE_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x04003C0100",
+        "MSRValue": "0x4003C0100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1643,7 +1658,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_HIT.NO_SNOOP_NEEDED",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x01003C0100",
+        "MSRValue": "0x1003C0100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1656,7 +1671,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_HIT.SNOOP_HIT_WITH_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x08003C0100",
+        "MSRValue": "0x8003C0100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/floating-point.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/floating-point.json
@@ -1,73 +1,81 @@
 [
     {
-        "BriefDescription": "Number of SSE/AVX computational 128-bit packed double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 2 computation operations, one for each element.  Applies to SSE* and AVX* packed double precision floating-point instructions: ADD SUB HADD HSUB SUBADD MUL DIV MIN MAX SQRT RSQRT14 RCP14 DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
+        "BriefDescription": "Counts once for most SIMD 128-bit packed computational double precision floating-point instructions retired. Counts twice for DPP and FM(N)ADD/SUB instructions retired.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE",
+        "PublicDescription": "Counts once for most SIMD 128-bit packed computational double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 2 computation operations, one for each element.  Applies to packed double precision floating-point instructions: ADD SUB HADD HSUB SUBADD MUL DIV MIN MAX SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x4"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational 128-bit packed single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 4 computation operations, one for each element.  Applies to SSE* and AVX* packed single precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
+        "BriefDescription": "Counts once for most SIMD 128-bit packed computational single precision floating-point instruction retired. Counts twice for DPP and FM(N)ADD/SUB instructions retired.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE",
+        "PublicDescription": "Counts once for most SIMD 128-bit packed computational single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 4 computation operations, one for each element.  Applies to packed single precision floating-point instructions: ADD SUB HADD HSUB SUBADD MUL DIV MIN MAX SQRT RSQRT RCP DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x8"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational 256-bit packed double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 4 computation operations, one for each element.  Applies to SSE* and AVX* packed double precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
+        "BriefDescription": "Counts once for most SIMD 256-bit packed double computational precision floating-point instructions retired. Counts twice for DPP and FM(N)ADD/SUB instructions retired.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE",
+        "PublicDescription": "Counts once for most SIMD 256-bit packed double computational precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 4 computation operations, one for each element.  Applies to packed double precision floating-point instructions: ADD SUB HADD HSUB SUBADD MUL DIV MIN MAX SQRT FM(N)ADD/SUB.  FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x10"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational 256-bit packed single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 8 computation operations, one for each element.  Applies to SSE* and AVX* packed single precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
+        "BriefDescription": "Counts once for most SIMD 256-bit packed single computational precision floating-point instructions retired. Counts twice for DPP and FM(N)ADD/SUB instructions retired.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE",
+        "PublicDescription": "Counts once for most SIMD 256-bit packed single computational precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 8 computation operations, one for each element.  Applies to packed single precision floating-point instructions: ADD SUB HADD HSUB SUBADD MUL DIV MIN MAX SQRT RSQRT RCP DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x20"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational 512-bit packed double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 8 computation operations, one for each element.  Applies to SSE* and AVX* packed double precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 8 calculations per element.",
+        "BriefDescription": "Counts number of SSE/AVX computational 512-bit packed double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 8 computation operations, one for each element.  Applies to SSE* and AVX* packed double precision floating-point instructions: ADD SUB MUL DIV MIN MAX SQRT RSQRT14 RCP14 FM(N)ADD/SUB. FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE",
+        "PublicDescription": "Number of SSE/AVX computational 512-bit packed double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 8 computation operations, one for each element.  Applies to SSE* and AVX* packed double precision floating-point instructions: ADD SUB MUL DIV MIN MAX SQRT RSQRT14 RCP14 FM(N)ADD/SUB. FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x40"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational 512-bit packed single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 16 computation operations, one for each element.  Applies to SSE* and AVX* packed single precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 16 calculations per element.",
+        "BriefDescription": "Counts number of SSE/AVX computational 512-bit packed single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 16 computation operations, one for each element.  Applies to SSE* and AVX* packed single precision floating-point instructions: ADD SUB MUL DIV MIN MAX SQRT RSQRT14 RCP14 FM(N)ADD/SUB. FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE",
+        "PublicDescription": "Number of SSE/AVX computational 512-bit packed single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 16 computation operations, one for each element.  Applies to SSE* and AVX* packed single precision floating-point instructions: ADD SUB MUL DIV MIN MAX SQRT RSQRT14 RCP14 FM(N)ADD/SUB. FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x80"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational scalar double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 1 computation. Applies to SSE* and AVX* scalar double precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
+        "BriefDescription": "Counts once for most SIMD scalar computational double precision floating-point instructions retired. Counts twice for DPP and FM(N)ADD/SUB instructions retired.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.SCALAR_DOUBLE",
+        "PublicDescription": "Counts once for most SIMD scalar computational double precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 1 computational operation. Applies to SIMD scalar double precision floating-point instructions: ADD SUB MUL DIV MIN MAX SQRT FM(N)ADD/SUB.  FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x1"
     },
     {
-        "BriefDescription": "Number of SSE/AVX computational scalar single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 1 computation. Applies to SSE* and AVX* scalar single precision floating-point instructions: ADD SUB MUL DIV MIN MAX RCP14 RSQRT14 SQRT DPP FM(N)ADD/SUB.  DPP and FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element.",
+        "BriefDescription": "Counts once for most SIMD scalar computational single precision floating-point instructions retired. Counts twice for DPP and FM(N)ADD/SUB instructions retired.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3,4,5,6,7",
         "EventCode": "0xC7",
         "EventName": "FP_ARITH_INST_RETIRED.SCALAR_SINGLE",
+        "PublicDescription": "Counts once for most SIMD scalar computational single precision floating-point instructions retired; some instructions will count twice as noted below.  Each count represents 1 computational operation. Applies to SIMD scalar single precision floating-point instructions: ADD SUB MUL DIV MIN MAX SQRT RSQRT RCP FM(N)ADD/SUB.  FM(N)ADD/SUB instructions count twice as they perform 2 calculations per element. The DAZ and FTZ flags in the MXCSR register need to be set when using these events.",
         "SampleAfterValue": "2000003",
         "UMask": "0x2"
     },
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/frontend.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/frontend.json
@@ -30,7 +30,21 @@
         "UMask": "0x2"
     },
     {
-        "BriefDescription": "Retired Instructions who experienced decode stream buffer (DSB - the decoded instruction-cache) miss.",
+        "BriefDescription": "Retired Instructions who experienced DSB miss.",
+        "Counter": "0,1,2,3",
+        "CounterHTOff": "0,1,2,3",
+        "EventCode": "0xC6",
+        "EventName": "FRONTEND_RETIRED.ANY_DSB_MISS",
+        "MSRIndex": "0x3F7",
+        "MSRValue": "0x1",
+        "PEBS": "1",
+        "PublicDescription": "Counts retired Instructions that experienced DSB (Decode stream buffer i.e. the decoded instruction-cache) miss.",
+        "SampleAfterValue": "100007",
+        "TakenAlone": "1",
+        "UMask": "0x1"
+    },
+    {
+        "BriefDescription": "Retired Instructions who experienced a critical DSB miss.",
         "Counter": "0,1,2,3",
         "CounterHTOff": "0,1,2,3",
         "EventCode": "0xC6",
@@ -38,7 +52,7 @@
         "MSRIndex": "0x3F7",
         "MSRValue": "0x11",
         "PEBS": "1",
-        "PublicDescription": "Counts retired Instructions that experienced DSB (Decode stream buffer i.e. the decoded instruction-cache) miss.",
+        "PublicDescription": "Number of retired Instructions that experienced a critical DSB (Decode stream buffer i.e. the decoded instruction-cache) miss. Critical means stalls were exposed to the back-end as a result of the DSB miss.",
         "SampleAfterValue": "100007",
         "TakenAlone": "1",
         "UMask": "0x1"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/memory.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/memory.json
@@ -299,7 +299,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00491",
+        "MSRValue": "0x83FC00491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -312,7 +312,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00491",
+        "MSRValue": "0x63FC00491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -325,7 +325,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000491",
+        "MSRValue": "0x604000491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -338,7 +338,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_DATA_RD.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800491",
+        "MSRValue": "0x63B800491",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -377,7 +377,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00490",
+        "MSRValue": "0x83FC00490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -390,7 +390,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00490",
+        "MSRValue": "0x63FC00490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -403,7 +403,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000490",
+        "MSRValue": "0x604000490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -416,7 +416,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_DATA_RD.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800490",
+        "MSRValue": "0x63B800490",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -455,7 +455,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00120",
+        "MSRValue": "0x83FC00120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -468,7 +468,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00120",
+        "MSRValue": "0x63FC00120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -481,7 +481,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000120",
+        "MSRValue": "0x604000120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -494,7 +494,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_PF_RFO.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800120",
+        "MSRValue": "0x63B800120",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -533,7 +533,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00122",
+        "MSRValue": "0x83FC00122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -546,7 +546,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00122",
+        "MSRValue": "0x63FC00122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -559,7 +559,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000122",
+        "MSRValue": "0x604000122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -572,7 +572,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.ALL_RFO.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800122",
+        "MSRValue": "0x63B800122",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -611,7 +611,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00004",
+        "MSRValue": "0x83FC00004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -624,7 +624,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00004",
+        "MSRValue": "0x63FC00004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -637,7 +637,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000004",
+        "MSRValue": "0x604000004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -650,7 +650,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_CODE_RD.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800004",
+        "MSRValue": "0x63B800004",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -689,7 +689,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00001",
+        "MSRValue": "0x83FC00001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -702,7 +702,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00001",
+        "MSRValue": "0x63FC00001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -715,7 +715,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000001",
+        "MSRValue": "0x604000001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -728,7 +728,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_DATA_RD.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800001",
+        "MSRValue": "0x63B800001",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -767,7 +767,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00002",
+        "MSRValue": "0x83FC00002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -780,7 +780,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00002",
+        "MSRValue": "0x63FC00002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -793,7 +793,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000002",
+        "MSRValue": "0x604000002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -806,7 +806,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.DEMAND_RFO.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800002",
+        "MSRValue": "0x63B800002",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -845,7 +845,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00400",
+        "MSRValue": "0x83FC00400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -858,7 +858,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00400",
+        "MSRValue": "0x63FC00400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -871,7 +871,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000400",
+        "MSRValue": "0x604000400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -884,7 +884,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L1D_AND_SW.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800400",
+        "MSRValue": "0x63B800400",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -923,7 +923,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00010",
+        "MSRValue": "0x83FC00010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -936,7 +936,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00010",
+        "MSRValue": "0x63FC00010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -949,7 +949,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000010",
+        "MSRValue": "0x604000010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -962,7 +962,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_DATA_RD.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800010",
+        "MSRValue": "0x63B800010",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1001,7 +1001,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00020",
+        "MSRValue": "0x83FC00020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1014,7 +1014,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00020",
+        "MSRValue": "0x63FC00020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1027,7 +1027,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000020",
+        "MSRValue": "0x604000020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1040,7 +1040,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L2_RFO.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800020",
+        "MSRValue": "0x63B800020",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1079,7 +1079,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00080",
+        "MSRValue": "0x83FC00080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1092,7 +1092,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00080",
+        "MSRValue": "0x63FC00080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1105,7 +1105,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000080",
+        "MSRValue": "0x604000080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1118,7 +1118,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_DATA_RD.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800080",
+        "MSRValue": "0x63B800080",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1157,7 +1157,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_MISS.REMOTE_HIT_FORWARD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x083FC00100",
+        "MSRValue": "0x83FC00100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1170,7 +1170,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_MISS.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063FC00100",
+        "MSRValue": "0x63FC00100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1183,7 +1183,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_MISS_LOCAL_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x0604000100",
+        "MSRValue": "0x604000100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
@@ -1196,7 +1196,7 @@
         "EventCode": "0xB7, 0xBB",
         "EventName": "OFFCORE_RESPONSE.PF_L3_RFO.L3_MISS_REMOTE_DRAM.SNOOP_MISS_OR_NO_FWD",
         "MSRIndex": "0x1a6,0x1a7",
-        "MSRValue": "0x063B800100",
+        "MSRValue": "0x63B800100",
         "Offcore": "1",
         "PublicDescription": "Offcore response can be programmed only with a specific pair of event select and counter MSR, and with specific event codes and predefine mask bit value in a dedicated MSR to specify attributes of the offcore transaction.",
         "SampleAfterValue": "100003",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/pipeline.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/pipeline.json
@@ -436,6 +436,17 @@
         "SampleAfterValue": "2000003"
     },
     {
+        "BriefDescription": "Number of all retired NOP instructions.",
+        "Counter": "0,1,2,3",
+        "CounterHTOff": "0,1,2,3,4,5,6,7",
+        "Errata": "SKL091, SKL044",
+        "EventCode": "0xC0",
+        "EventName": "INST_RETIRED.NOP",
+        "PEBS": "1",
+        "SampleAfterValue": "2000003",
+        "UMask": "0x2"
+    },
+    {
         "BriefDescription": "Precise instruction retired event with HW to reduce effect of PEBS shadow in IP distribution",
         "Counter": "1",
         "CounterHTOff": "1",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/skx-metrics.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/skx-metrics.json
@@ -1,26 +1,167 @@
 [
     {
+        "BriefDescription": "This category represents fraction of slots where the processor's Frontend undersupplies its Backend",
+        "MetricExpr": "IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)",
+        "MetricGroup": "TopdownL1",
+        "MetricName": "Frontend_Bound",
+        "PublicDescription": "This category represents fraction of slots where the processor's Frontend undersupplies its Backend. Frontend denotes the first part of the processor core responsible to fetch operations that are executed later on by the Backend part. Within the Frontend; a branch predictor predicts the next address to fetch; cache-lines are fetched from the memory subsystem; parsed into instructions; and lastly decoded into micro-operations (uops). Ideally the Frontend can issue Machine_Width uops every cycle to the Backend. Frontend Bound denotes unutilized issue-slots when there is no Backend stall; i.e. bubbles where Frontend delivered no uops while Backend could have accepted them. For example; stalls due to instruction-cache misses would be categorized under Frontend Bound."
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots where the processor's Frontend undersupplies its Backend. SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))",
+        "MetricGroup": "TopdownL1_SMT",
+        "MetricName": "Frontend_Bound_SMT",
+        "PublicDescription": "This category represents fraction of slots where the processor's Frontend undersupplies its Backend. Frontend denotes the first part of the processor core responsible to fetch operations that are executed later on by the Backend part. Within the Frontend; a branch predictor predicts the next address to fetch; cache-lines are fetched from the memory subsystem; parsed into instructions; and lastly decoded into micro-operations (uops). Ideally the Frontend can issue Machine_Width uops every cycle to the Backend. Frontend Bound denotes unutilized issue-slots when there is no Backend stall; i.e. bubbles where Frontend delivered no uops while Backend could have accepted them. For example; stalls due to instruction-cache misses would be categorized under Frontend Bound. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots wasted due to incorrect speculations",
+        "MetricExpr": "( UOPS_ISSUED.ANY - UOPS_RETIRED.RETIRE_SLOTS + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD)",
+        "MetricGroup": "TopdownL1",
+        "MetricName": "Bad_Speculation",
+        "PublicDescription": "This category represents fraction of slots wasted due to incorrect speculations. This include slots used to issue uops that do not eventually get retired and slots for which the issue-pipeline was blocked due to recovery from earlier incorrect speculation. For example; wasted work due to miss-predicted branches are categorized under Bad Speculation category. Incorrect data speculation followed by Memory Ordering Nukes is another example."
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots wasted due to incorrect speculations. SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "( UOPS_ISSUED.ANY - UOPS_RETIRED.RETIRE_SLOTS + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))",
+        "MetricGroup": "TopdownL1_SMT",
+        "MetricName": "Bad_Speculation_SMT",
+        "PublicDescription": "This category represents fraction of slots wasted due to incorrect speculations. This include slots used to issue uops that do not eventually get retired and slots for which the issue-pipeline was blocked due to recovery from earlier incorrect speculation. For example; wasted work due to miss-predicted branches are categorized under Bad Speculation category. Incorrect data speculation followed by Memory Ordering Nukes is another example. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots where no uops are being delivered due to a lack of required resources for accepting new uops in the Backend",
+        "MetricConstraint": "NO_NMI_WATCHDOG",
+        "MetricExpr": "1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD)",
+        "MetricGroup": "TopdownL1",
+        "MetricName": "Backend_Bound",
+        "PublicDescription": "This category represents fraction of slots where no uops are being delivered due to a lack of required resources for accepting new uops in the Backend. Backend is the portion of the processor core where the out-of-order scheduler dispatches ready uops into their respective execution units; and once completed these uops get retired according to program order. For example; stalls due to data-cache misses or stalls due to the divider unit being overloaded are both categorized under Backend Bound. Backend Bound is further divided into two main categories: Memory Bound and Core Bound."
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots where no uops are being delivered due to a lack of required resources for accepting new uops in the Backend. SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))",
+        "MetricGroup": "TopdownL1_SMT",
+        "MetricName": "Backend_Bound_SMT",
+        "PublicDescription": "This category represents fraction of slots where no uops are being delivered due to a lack of required resources for accepting new uops in the Backend. Backend is the portion of the processor core where the out-of-order scheduler dispatches ready uops into their respective execution units; and once completed these uops get retired according to program order. For example; stalls due to data-cache misses or stalls due to the divider unit being overloaded are both categorized under Backend Bound. Backend Bound is further divided into two main categories: Memory Bound and Core Bound. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots utilized by useful work i.e. issued uops that eventually get retired",
+        "MetricExpr": "UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)",
+        "MetricGroup": "TopdownL1",
+        "MetricName": "Retiring",
+        "PublicDescription": "This category represents fraction of slots utilized by useful work i.e. issued uops that eventually get retired. Ideally; all pipeline slots would be attributed to the Retiring category.  Retiring of 100% would indicate the maximum Pipeline_Width throughput was achieved.  Maximizing Retiring typically increases the Instructions-per-cycle (see IPC metric). Note that a high Retiring value does not necessary mean there is no room for more performance.  For example; Heavy-operations or Microcode Assists are categorized under Retiring. They often indicate suboptimal performance and can often be optimized or avoided. "
+    },
+    {
+        "BriefDescription": "This category represents fraction of slots utilized by useful work i.e. issued uops that eventually get retired. SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))",
+        "MetricGroup": "TopdownL1_SMT",
+        "MetricName": "Retiring_SMT",
+        "PublicDescription": "This category represents fraction of slots utilized by useful work i.e. issued uops that eventually get retired. Ideally; all pipeline slots would be attributed to the Retiring category.  Retiring of 100% would indicate the maximum Pipeline_Width throughput was achieved.  Maximizing Retiring typically increases the Instructions-per-cycle (see IPC metric). Note that a high Retiring value does not necessary mean there is no room for more performance.  For example; Heavy-operations or Microcode Assists are categorized under Retiring. They often indicate suboptimal performance and can often be optimized or avoided. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
+        "BriefDescription": "Total pipeline cost of Branch Misprediction related bottlenecks",
+        "MetricExpr": "100 * ( ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * (( UOPS_ISSUED.ANY - UOPS_RETIRED.RETIRE_SLOTS + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) + (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) * ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * INT_MISC.CLEAR_RESTEER_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) )",
+        "MetricGroup": "Bad;BadSpec;BrMispredicts",
+        "MetricName": "Mispredictions"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of Branch Misprediction related bottlenecks",
+        "MetricExpr": "100 * ( ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * (( UOPS_ISSUED.ANY - UOPS_RETIRED.RETIRE_SLOTS + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) + (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * INT_MISC.CLEAR_RESTEER_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) )",
+        "MetricGroup": "Bad;BadSpec;BrMispredicts_SMT",
+        "MetricName": "Mispredictions_SMT"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of (external) Memory Bandwidth related bottlenecks",
+        "MetricExpr": "100 * ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) * ( ( (CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( (min( CPU_CLK_UNHALTED.THREAD , cpu@OFFCORE_REQUESTS_OUTSTANDING.ALL_DATA_RD\\,cmask\\=4@ ) / CPU_CLK_UNHALTED.THREAD) / #(CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) ) + ( (( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( (OFFCORE_REQUESTS_BUFFER.SQ_FULL / CPU_CLK_UNHALTED.THREAD) / #(( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) ) ) + ( (max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( ((L1D_PEND_MISS.PENDING / ( MEM_LOAD_RETIRED.L1_MISS + MEM_LOAD_RETIRED.FB_HIT )) * cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ / CPU_CLK_UNHALTED.THREAD) / #(max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) ) ",
+        "MetricGroup": "Mem;MemoryBW;Offcore",
+        "MetricName": "Memory_Bandwidth"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of (external) Memory Bandwidth related bottlenecks",
+        "MetricExpr": "100 * ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) * ( ( (CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( (min( CPU_CLK_UNHALTED.THREAD , cpu@OFFCORE_REQUESTS_OUTSTANDING.ALL_DATA_RD\\,cmask\\=4@ ) / CPU_CLK_UNHALTED.THREAD) / #(CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) ) + ( (( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( (( OFFCORE_REQUESTS_BUFFER.SQ_FULL / 2 ) / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )) / #(( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) ) ) + ( (max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( ((L1D_PEND_MISS.PENDING / ( MEM_LOAD_RETIRED.L1_MISS + MEM_LOAD_RETIRED.FB_HIT )) * cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ / CPU_CLK_UNHALTED.THREAD) / #(max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) ) ",
+        "MetricGroup": "Mem;MemoryBW;Offcore_SMT",
+        "MetricName": "Memory_Bandwidth_SMT"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of Memory Latency related bottlenecks (external memory and off-core caches)",
+        "MetricExpr": "100 * ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) * ( ( (CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( (min( CPU_CLK_UNHALTED.THREAD , OFFCORE_REQUESTS_OUTSTANDING.CYCLES_WITH_DATA_RD ) / CPU_CLK_UNHALTED.THREAD - (min( CPU_CLK_UNHALTED.THREAD , cpu@OFFCORE_REQUESTS_OUTSTANDING.ALL_DATA_RD\\,cmask\\=4@ ) / CPU_CLK_UNHALTED.THREAD)) / #(CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) ) + ( (( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( (( (20.5 * ((CPU_CLK_UNHALTED.THREAD / CPU_CLK_UNHALTED.REF_TSC) * msr@tsc@ / 1000000000 / duration_time)) - (3.5 * ((CPU_CLK_UNHALTED.THREAD / CPU_CLK_UNHALTED.REF_TSC) * msr@tsc@ / 1000000000 / duration_time)) ) * MEM_LOAD_RETIRED.L3_HIT * (1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) / 2) / CPU_CLK_UNHALTED.THREAD) / #(( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) ) + ( (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD)) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) )",
+        "MetricGroup": "Mem;MemoryLat;Offcore",
+        "MetricName": "Memory_Latency"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of Memory Latency related bottlenecks (external memory and off-core caches)",
+        "MetricExpr": "100 * ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) * ( ( (CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( (min( CPU_CLK_UNHALTED.THREAD , OFFCORE_REQUESTS_OUTSTANDING.CYCLES_WITH_DATA_RD ) / CPU_CLK_UNHALTED.THREAD - (min( CPU_CLK_UNHALTED.THREAD , cpu@OFFCORE_REQUESTS_OUTSTANDING.ALL_DATA_RD\\,cmask\\=4@ ) / CPU_CLK_UNHALTED.THREAD)) / #(CYCLE_ACTIVITY.STALLS_L3_MISS / CPU_CLK_UNHALTED.THREAD + (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD) - (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD))) ) + ( (( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( (( (20.5 * ((CPU_CLK_UNHALTED.THREAD / CPU_CLK_UNHALTED.REF_TSC) * msr@tsc@ / 1000000000 / duration_time)) - (3.5 * ((CPU_CLK_UNHALTED.THREAD / CPU_CLK_UNHALTED.REF_TSC) * msr@tsc@ / 1000000000 / duration_time)) ) * MEM_LOAD_RETIRED.L3_HIT * (1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) / 2) / CPU_CLK_UNHALTED.THREAD) / #(( CYCLE_ACTIVITY.STALLS_L2_MISS - CYCLE_ACTIVITY.STALLS_L3_MISS ) / CPU_CLK_UNHALTED.THREAD) ) + ( (( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) / ( (MEM_LOAD_RETIRED.L2_HIT * ( 1 + (MEM_LOAD_RETIRED.FB_HIT / MEM_LOAD_RETIRED.L1_MISS) )) + cpu@L1D_PEND_MISS.FB_FULL\\,cmask\\=1@ ) ) * (( CYCLE_ACTIVITY.STALLS_L1D_MISS - CYCLE_ACTIVITY.STALLS_L2_MISS ) / CPU_CLK_UNHALTED.THREAD)) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) )",
+        "MetricGroup": "Mem;MemoryLat;Offcore_SMT",
+        "MetricName": "Memory_Latency_SMT"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of Memory Address Translation related bottlenecks (data-side TLBs)",
+        "MetricExpr": "100 * ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) * ( ( (max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) / ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( (min( 9 * cpu@DTLB_LOAD_MISSES.STLB_HIT\\,cmask\\=1@ + DTLB_LOAD_MISSES.WALK_ACTIVE , max( CYCLE_ACTIVITY.CYCLES_MEM_ANY - CYCLE_ACTIVITY.CYCLES_L1D_MISS , 0 ) ) / CPU_CLK_UNHALTED.THREAD) / (max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) ) + ( (EXE_ACTIVITY.BOUND_ON_STORES / CPU_CLK_UNHALTED.THREAD) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * CPU_CLK_UNHALTED.THREAD)) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - ( UOPS_ISSUED.ANY + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) ) * ( (( 9 * cpu@DTLB_STORE_MISSES.STLB_HIT\\,cmask\\=1@ + DTLB_STORE_MISSES.WALK_ACTIVE ) / CPU_CLK_UNHALTED.THREAD) / #(EXE_ACTIVITY.BOUND_ON_STORES / CPU_CLK_UNHALTED.THREAD) ) ) ",
+        "MetricGroup": "Mem;MemoryTLB",
+        "MetricName": "Memory_Data_TLBs"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of Memory Address Translation related bottlenecks (data-side TLBs)",
+        "MetricExpr": "100 * ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) * ( ( (max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) / ((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( (min( 9 * cpu@DTLB_LOAD_MISSES.STLB_HIT\\,cmask\\=1@ + DTLB_LOAD_MISSES.WALK_ACTIVE , max( CYCLE_ACTIVITY.CYCLES_MEM_ANY - CYCLE_ACTIVITY.CYCLES_L1D_MISS , 0 ) ) / CPU_CLK_UNHALTED.THREAD) / (max( ( CYCLE_ACTIVITY.STALLS_MEM_ANY - CYCLE_ACTIVITY.STALLS_L1D_MISS ) / CPU_CLK_UNHALTED.THREAD , 0 )) ) + ( (EXE_ACTIVITY.BOUND_ON_STORES / CPU_CLK_UNHALTED.THREAD) / #((( CYCLE_ACTIVITY.STALLS_MEM_ANY + EXE_ACTIVITY.BOUND_ON_STORES ) / (CYCLE_ACTIVITY.STALLS_TOTAL + (EXE_ACTIVITY.1_PORTS_UTIL + (UOPS_RETIRED.RETIRE_SLOTS / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * EXE_ACTIVITY.2_PORTS_UTIL) + EXE_ACTIVITY.BOUND_ON_STORES)) * (1 - (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - ( UOPS_ISSUED.ANY + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) ) * ( (( 9 * cpu@DTLB_STORE_MISSES.STLB_HIT\\,cmask\\=1@ + DTLB_STORE_MISSES.WALK_ACTIVE ) / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )) / #(EXE_ACTIVITY.BOUND_ON_STORES / CPU_CLK_UNHALTED.THREAD) ) ) ",
+        "MetricGroup": "Mem;MemoryTLB;_SMT",
+        "MetricName": "Memory_Data_TLBs_SMT"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of branch related instructions (used for program control-flow including function calls)",
+        "MetricExpr": "100 * (( BR_INST_RETIRED.CONDITIONAL + 3 * BR_INST_RETIRED.NEAR_CALL + (BR_INST_RETIRED.NEAR_TAKEN - ( BR_INST_RETIRED.CONDITIONAL - BR_INST_RETIRED.NOT_TAKEN ) - 2 * BR_INST_RETIRED.NEAR_CALL) ) / (4 * CPU_CLK_UNHALTED.THREAD))",
+        "MetricGroup": "Ret",
+        "MetricName": "Branching_Overhead"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of branch related instructions (used for program control-flow including function calls)",
+        "MetricExpr": "100 * (( BR_INST_RETIRED.CONDITIONAL + 3 * BR_INST_RETIRED.NEAR_CALL + (BR_INST_RETIRED.NEAR_TAKEN - ( BR_INST_RETIRED.CONDITIONAL - BR_INST_RETIRED.NOT_TAKEN ) - 2 * BR_INST_RETIRED.NEAR_CALL) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))",
+        "MetricGroup": "Ret_SMT",
+        "MetricName": "Branching_Overhead_SMT"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of instruction fetch related bottlenecks by large code footprint programs (i-side cache; TLB and BTB misses)",
+        "MetricExpr": "100 * (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) * ( (ICACHE_64B.IFTAG_STALL / CPU_CLK_UNHALTED.THREAD) + (( ICACHE_16B.IFDATA_STALL + 2 * cpu@ICACHE_16B.IFDATA_STALL\\,cmask\\=1\\,edge@ ) / CPU_CLK_UNHALTED.THREAD) + (9 * BACLEARS.ANY / CPU_CLK_UNHALTED.THREAD) ) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD))",
+        "MetricGroup": "BigFoot;Fed;Frontend;IcMiss;MemoryTLB",
+        "MetricName": "Big_Code"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of instruction fetch related bottlenecks by large code footprint programs (i-side cache; TLB and BTB misses)",
+        "MetricExpr": "100 * (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * ( (ICACHE_64B.IFTAG_STALL / CPU_CLK_UNHALTED.THREAD) + (( ICACHE_16B.IFDATA_STALL + 2 * cpu@ICACHE_16B.IFDATA_STALL\\,cmask\\=1\\,edge@ ) / CPU_CLK_UNHALTED.THREAD) + (9 * BACLEARS.ANY / CPU_CLK_UNHALTED.THREAD) ) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))",
+        "MetricGroup": "BigFoot;Fed;Frontend;IcMiss;MemoryTLB_SMT",
+        "MetricName": "Big_Code_SMT"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of instruction fetch bandwidth related bottlenecks",
+        "MetricExpr": "100 * ( (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) * ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * INT_MISC.CLEAR_RESTEER_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) ) - (100 * (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) * ( (ICACHE_64B.IFTAG_STALL / CPU_CLK_UNHALTED.THREAD) + (( ICACHE_16B.IFDATA_STALL + 2 * cpu@ICACHE_16B.IFDATA_STALL\\,cmask\\=1\\,edge@ ) / CPU_CLK_UNHALTED.THREAD) + (9 * BACLEARS.ANY / CPU_CLK_UNHALTED.THREAD) ) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)))",
+        "MetricGroup": "Fed;FetchBW;Frontend",
+        "MetricName": "Instruction_Fetch_BW"
+    },
+    {
+        "BriefDescription": "Total pipeline cost of instruction fetch bandwidth related bottlenecks",
+        "MetricExpr": "100 * ( (IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * INT_MISC.CLEAR_RESTEER_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) ) - (100 * (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * ( (ICACHE_64B.IFTAG_STALL / CPU_CLK_UNHALTED.THREAD) + (( ICACHE_16B.IFDATA_STALL + 2 * cpu@ICACHE_16B.IFDATA_STALL\\,cmask\\=1\\,edge@ ) / CPU_CLK_UNHALTED.THREAD) + (9 * BACLEARS.ANY / CPU_CLK_UNHALTED.THREAD) ) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))))",
+        "MetricGroup": "Fed;FetchBW;Frontend_SMT",
+        "MetricName": "Instruction_Fetch_BW_SMT"
+    },
+    {
         "BriefDescription": "Instructions Per Cycle (per Logical Processor)",
         "MetricExpr": "INST_RETIRED.ANY / CPU_CLK_UNHALTED.THREAD",
-        "MetricGroup": "Summary",
+        "MetricGroup": "Ret;Summary",
         "MetricName": "IPC"
     },
     {
         "BriefDescription": "Uops Per Instruction",
         "MetricExpr": "UOPS_RETIRED.RETIRE_SLOTS / INST_RETIRED.ANY",
-        "MetricGroup": "Pipeline;Retire",
+        "MetricGroup": "Pipeline;Ret;Retire",
         "MetricName": "UPI"
     },
     {
         "BriefDescription": "Instruction per taken branch",
-        "MetricExpr": "INST_RETIRED.ANY / BR_INST_RETIRED.NEAR_TAKEN",
-        "MetricGroup": "Branches;FetchBW;PGO",
-        "MetricName": "IpTB"
+        "MetricExpr": "UOPS_RETIRED.RETIRE_SLOTS / BR_INST_RETIRED.NEAR_TAKEN",
+        "MetricGroup": "Branches;Fed;FetchBW",
+        "MetricName": "UpTB"
     },
     {
         "BriefDescription": "Cycles Per Instruction (per Logical Processor)",
         "MetricExpr": "1 / (INST_RETIRED.ANY / CPU_CLK_UNHALTED.THREAD)",
-        "MetricGroup": "Pipeline",
+        "MetricGroup": "Pipeline;Mem",
         "MetricName": "CPI"
     },
     {
@@ -30,39 +171,84 @@
         "MetricName": "CLKS"
     },
     {
-        "BriefDescription": "Instructions Per Cycle (per physical core)",
+        "BriefDescription": "Total issue-pipeline slots (per-Physical Core till ICL; per-Logical Processor ICL onward)",
+        "MetricExpr": "4 * CPU_CLK_UNHALTED.THREAD",
+        "MetricGroup": "TmaL1",
+        "MetricName": "SLOTS"
+    },
+    {
+        "BriefDescription": "Total issue-pipeline slots (per-Physical Core till ICL; per-Logical Processor ICL onward)",
+        "MetricExpr": "4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )",
+        "MetricGroup": "TmaL1_SMT",
+        "MetricName": "SLOTS_SMT"
+    },
+    {
+        "BriefDescription": "The ratio of Executed- by Issued-Uops",
+        "MetricExpr": "UOPS_EXECUTED.THREAD / UOPS_ISSUED.ANY",
+        "MetricGroup": "Cor;Pipeline",
+        "MetricName": "Execute_per_Issue",
+        "PublicDescription": "The ratio of Executed- by Issued-Uops. Ratio > 1 suggests high rate of uop micro-fusions. Ratio < 1 suggest high rate of \"execute\" at rename stage."
+    },
+    {
+        "BriefDescription": "Instructions Per Cycle across hyper-threads (per physical core)",
         "MetricExpr": "INST_RETIRED.ANY / CPU_CLK_UNHALTED.THREAD",
-        "MetricGroup": "SMT;TmaL1",
+        "MetricGroup": "Ret;SMT;TmaL1",
         "MetricName": "CoreIPC"
     },
     {
-        "BriefDescription": "Instructions Per Cycle (per physical core)",
+        "BriefDescription": "Instructions Per Cycle across hyper-threads (per physical core)",
         "MetricExpr": "INST_RETIRED.ANY / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )",
-        "MetricGroup": "SMT;TmaL1",
+        "MetricGroup": "Ret;SMT;TmaL1_SMT",
         "MetricName": "CoreIPC_SMT"
     },
     {
         "BriefDescription": "Floating Point Operations Per Cycle",
         "MetricExpr": "( 1 * ( FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE ) + 2 * FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + 4 * ( FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE ) + 8 * ( FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE ) + 16 * FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE ) / CPU_CLK_UNHALTED.THREAD",
-        "MetricGroup": "Flops",
+        "MetricGroup": "Ret;Flops",
         "MetricName": "FLOPc"
     },
     {
         "BriefDescription": "Floating Point Operations Per Cycle",
         "MetricExpr": "( 1 * ( FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE ) + 2 * FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + 4 * ( FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE ) + 8 * ( FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE ) + 16 * FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE ) / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )",
-        "MetricGroup": "Flops_SMT",
+        "MetricGroup": "Ret;Flops_SMT",
         "MetricName": "FLOPc_SMT"
     },
     {
+        "BriefDescription": "Actual per-core usage of the Floating Point execution units (regardless of the vector width)",
+        "MetricExpr": "( (FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE) + (FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE) ) / ( 2 * CPU_CLK_UNHALTED.THREAD )",
+        "MetricGroup": "Cor;Flops;HPC",
+        "MetricName": "FP_Arith_Utilization",
+        "PublicDescription": "Actual per-core usage of the Floating Point execution units (regardless of the vector width). Values > 1 are possible due to Fused-Multiply Add (FMA) counting."
+    },
+    {
+        "BriefDescription": "Actual per-core usage of the Floating Point execution units (regardless of the vector width). SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "( (FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE) + (FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE) ) / ( 2 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ) )",
+        "MetricGroup": "Cor;Flops;HPC_SMT",
+        "MetricName": "FP_Arith_Utilization_SMT",
+        "PublicDescription": "Actual per-core usage of the Floating Point execution units (regardless of the vector width). Values > 1 are possible due to Fused-Multiply Add (FMA) counting. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
         "BriefDescription": "Instruction-Level-Parallelism (average number of uops executed when there is at least 1 uop executed)",
         "MetricExpr": "UOPS_EXECUTED.THREAD / (( UOPS_EXECUTED.CORE_CYCLES_GE_1 / 2 ) if #SMT_on else UOPS_EXECUTED.CORE_CYCLES_GE_1)",
-        "MetricGroup": "Pipeline;PortsUtil",
+        "MetricGroup": "Backend;Cor;Pipeline;PortsUtil",
         "MetricName": "ILP"
     },
     {
+        "BriefDescription": "Branch Misprediction Cost: Fraction of TMA slots wasted per non-speculative branch misprediction (retired JEClear)",
+        "MetricExpr": " ( ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * (( UOPS_ISSUED.ANY - UOPS_RETIRED.RETIRE_SLOTS + 4 * INT_MISC.RECOVERY_CYCLES ) / (4 * CPU_CLK_UNHALTED.THREAD))) + (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) * ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * INT_MISC.CLEAR_RESTEER_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) ) * (4 * CPU_CLK_UNHALTED.THREAD) / BR_MISP_RETIRED.ALL_BRANCHES",
+        "MetricGroup": "Bad;BrMispredicts",
+        "MetricName": "Branch_Misprediction_Cost"
+    },
+    {
+        "BriefDescription": "Branch Misprediction Cost: Fraction of TMA slots wasted per non-speculative branch misprediction (retired JEClear)",
+        "MetricExpr": " ( ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * (( UOPS_ISSUED.ANY - UOPS_RETIRED.RETIRE_SLOTS + 4 * ( INT_MISC.RECOVERY_CYCLES_ANY / 2 ) ) / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) + (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * ((BR_MISP_RETIRED.ALL_BRANCHES / ( BR_MISP_RETIRED.ALL_BRANCHES + MACHINE_CLEARS.COUNT )) * INT_MISC.CLEAR_RESTEER_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) ) * (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )) / BR_MISP_RETIRED.ALL_BRANCHES",
+        "MetricGroup": "Bad;BrMispredicts_SMT",
+        "MetricName": "Branch_Misprediction_Cost_SMT"
+    },
+    {
         "BriefDescription": "Number of Instructions per non-speculative Branch Misprediction (JEClear)",
         "MetricExpr": "INST_RETIRED.ANY / BR_MISP_RETIRED.ALL_BRANCHES",
-        "MetricGroup": "BrMispredicts",
+        "MetricGroup": "Bad;BadSpec;BrMispredicts",
         "MetricName": "IpMispredict"
     },
     {
@@ -86,122 +272,249 @@
     {
         "BriefDescription": "Instructions per Branch (lower number means higher occurrence rate)",
         "MetricExpr": "INST_RETIRED.ANY / BR_INST_RETIRED.ALL_BRANCHES",
-        "MetricGroup": "Branches;InsType",
+        "MetricGroup": "Branches;Fed;InsType",
         "MetricName": "IpBranch"
     },
     {
         "BriefDescription": "Instructions per (near) call (lower number means higher occurrence rate)",
         "MetricExpr": "INST_RETIRED.ANY / BR_INST_RETIRED.NEAR_CALL",
-        "MetricGroup": "Branches",
+        "MetricGroup": "Branches;Fed;PGO",
         "MetricName": "IpCall"
     },
     {
+        "BriefDescription": "Instruction per taken branch",
+        "MetricExpr": "INST_RETIRED.ANY / BR_INST_RETIRED.NEAR_TAKEN",
+        "MetricGroup": "Branches;Fed;FetchBW;Frontend;PGO",
+        "MetricName": "IpTB"
+    },
+    {
         "BriefDescription": "Branch instructions per taken branch. ",
         "MetricExpr": "BR_INST_RETIRED.ALL_BRANCHES / BR_INST_RETIRED.NEAR_TAKEN",
-        "MetricGroup": "Branches;PGO",
+        "MetricGroup": "Branches;Fed;PGO",
         "MetricName": "BpTkBranch"
     },
     {
         "BriefDescription": "Instructions per Floating Point (FP) Operation (lower number means higher occurrence rate)",
         "MetricExpr": "INST_RETIRED.ANY / ( 1 * ( FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE ) + 2 * FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + 4 * ( FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE ) + 8 * ( FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE ) + 16 * FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE )",
-        "MetricGroup": "Flops;FpArith;InsType",
+        "MetricGroup": "Flops;InsType",
         "MetricName": "IpFLOP"
     },
     {
+        "BriefDescription": "Instructions per FP Arithmetic instruction (lower number means higher occurrence rate)",
+        "MetricExpr": "INST_RETIRED.ANY / ( (FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE) + (FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE) )",
+        "MetricGroup": "Flops;InsType",
+        "MetricName": "IpArith",
+        "PublicDescription": "Instructions per FP Arithmetic instruction (lower number means higher occurrence rate). May undercount due to FMA double counting. Approximated prior to BDW."
+    },
+    {
+        "BriefDescription": "Instructions per FP Arithmetic Scalar Single-Precision instruction (lower number means higher occurrence rate)",
+        "MetricExpr": "INST_RETIRED.ANY / FP_ARITH_INST_RETIRED.SCALAR_SINGLE",
+        "MetricGroup": "Flops;FpScalar;InsType",
+        "MetricName": "IpArith_Scalar_SP",
+        "PublicDescription": "Instructions per FP Arithmetic Scalar Single-Precision instruction (lower number means higher occurrence rate). May undercount due to FMA double counting."
+    },
+    {
+        "BriefDescription": "Instructions per FP Arithmetic Scalar Double-Precision instruction (lower number means higher occurrence rate)",
+        "MetricExpr": "INST_RETIRED.ANY / FP_ARITH_INST_RETIRED.SCALAR_DOUBLE",
+        "MetricGroup": "Flops;FpScalar;InsType",
+        "MetricName": "IpArith_Scalar_DP",
+        "PublicDescription": "Instructions per FP Arithmetic Scalar Double-Precision instruction (lower number means higher occurrence rate). May undercount due to FMA double counting."
+    },
+    {
+        "BriefDescription": "Instructions per FP Arithmetic AVX/SSE 128-bit instruction (lower number means higher occurrence rate)",
+        "MetricExpr": "INST_RETIRED.ANY / ( FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE )",
+        "MetricGroup": "Flops;FpVector;InsType",
+        "MetricName": "IpArith_AVX128",
+        "PublicDescription": "Instructions per FP Arithmetic AVX/SSE 128-bit instruction (lower number means higher occurrence rate). May undercount due to FMA double counting."
+    },
+    {
+        "BriefDescription": "Instructions per FP Arithmetic AVX* 256-bit instruction (lower number means higher occurrence rate)",
+        "MetricExpr": "INST_RETIRED.ANY / ( FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE )",
+        "MetricGroup": "Flops;FpVector;InsType",
+        "MetricName": "IpArith_AVX256",
+        "PublicDescription": "Instructions per FP Arithmetic AVX* 256-bit instruction (lower number means higher occurrence rate). May undercount due to FMA double counting."
+    },
+    {
+        "BriefDescription": "Instructions per FP Arithmetic AVX 512-bit instruction (lower number means higher occurrence rate)",
+        "MetricExpr": "INST_RETIRED.ANY / ( FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE + FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE )",
+        "MetricGroup": "Flops;FpVector;InsType",
+        "MetricName": "IpArith_AVX512",
+        "PublicDescription": "Instructions per FP Arithmetic AVX 512-bit instruction (lower number means higher occurrence rate). May undercount due to FMA double counting."
+    },
+    {
         "BriefDescription": "Total number of retired Instructions, Sample with: INST_RETIRED.PREC_DIST",
         "MetricExpr": "INST_RETIRED.ANY",
         "MetricGroup": "Summary;TmaL1",
         "MetricName": "Instructions"
     },
     {
+        "BriefDescription": "Average number of Uops issued by front-end when it issued something",
+        "MetricExpr": "UOPS_ISSUED.ANY / cpu@UOPS_ISSUED.ANY\\,cmask\\=1@",
+        "MetricGroup": "Fed;FetchBW",
+        "MetricName": "Fetch_UpC"
+    },
+    {
         "BriefDescription": "Fraction of Uops delivered by the DSB (aka Decoded ICache; or Uop Cache)",
         "MetricExpr": "IDQ.DSB_UOPS / (IDQ.DSB_UOPS + IDQ.MITE_UOPS + IDQ.MS_UOPS)",
-        "MetricGroup": "DSB;FetchBW",
+        "MetricGroup": "DSB;Fed;FetchBW",
         "MetricName": "DSB_Coverage"
     },
     {
-        "BriefDescription": "Actual Average Latency for L1 data-cache miss demand loads (in core cycles)",
+        "BriefDescription": "Total penalty related to DSB (uop cache) misses - subset/see of/the Instruction_Fetch_BW Bottleneck.",
+        "MetricExpr": "(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) * (DSB2MITE_SWITCHES.PENALTY_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) + ((IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD))) * (( IDQ.ALL_MITE_CYCLES_ANY_UOPS - IDQ.ALL_MITE_CYCLES_4_UOPS ) / CPU_CLK_UNHALTED.THREAD / 2) / #((IDQ_UOPS_NOT_DELIVERED.CORE / (4 * CPU_CLK_UNHALTED.THREAD)) - (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * CPU_CLK_UNHALTED.THREAD)))",
+        "MetricGroup": "DSBmiss;Fed",
+        "MetricName": "DSB_Misses_Cost"
+    },
+    {
+        "BriefDescription": "Total penalty related to DSB (uop cache) misses - subset/see of/the Instruction_Fetch_BW Bottleneck.",
+        "MetricExpr": "(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) * (DSB2MITE_SWITCHES.PENALTY_CYCLES / CPU_CLK_UNHALTED.THREAD) / #(4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) + ((IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )))) * (( IDQ.ALL_MITE_CYCLES_ANY_UOPS - IDQ.ALL_MITE_CYCLES_4_UOPS ) / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ) / 2) / #((IDQ_UOPS_NOT_DELIVERED.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))) - (4 * IDQ_UOPS_NOT_DELIVERED.CYCLES_0_UOPS_DELIV.CORE / (4 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ))))",
+        "MetricGroup": "DSBmiss;Fed_SMT",
+        "MetricName": "DSB_Misses_Cost_SMT"
+    },
+    {
+        "BriefDescription": "Number of Instructions per non-speculative DSB miss",
+        "MetricExpr": "INST_RETIRED.ANY / FRONTEND_RETIRED.ANY_DSB_MISS",
+        "MetricGroup": "DSBmiss;Fed",
+        "MetricName": "IpDSB_Miss_Ret"
+    },
+    {
+        "BriefDescription": "Fraction of branches that are non-taken conditionals",
+        "MetricExpr": "BR_INST_RETIRED.NOT_TAKEN / BR_INST_RETIRED.ALL_BRANCHES",
+        "MetricGroup": "Bad;Branches;CodeGen;PGO",
+        "MetricName": "Cond_NT"
+    },
+    {
+        "BriefDescription": "Fraction of branches that are taken conditionals",
+        "MetricExpr": "( BR_INST_RETIRED.CONDITIONAL - BR_INST_RETIRED.NOT_TAKEN )  / BR_INST_RETIRED.ALL_BRANCHES",
+        "MetricGroup": "Bad;Branches;CodeGen;PGO",
+        "MetricName": "Cond_TK"
+    },
+    {
+        "BriefDescription": "Fraction of branches that are CALL or RET",
+        "MetricExpr": "( BR_INST_RETIRED.NEAR_CALL + BR_INST_RETIRED.NEAR_RETURN ) / BR_INST_RETIRED.ALL_BRANCHES",
+        "MetricGroup": "Bad;Branches",
+        "MetricName": "CallRet"
+    },
+    {
+        "BriefDescription": "Fraction of branches that are unconditional (direct or indirect) jumps",
+        "MetricExpr": "(BR_INST_RETIRED.NEAR_TAKEN - ( BR_INST_RETIRED.CONDITIONAL - BR_INST_RETIRED.NOT_TAKEN ) - 2 * BR_INST_RETIRED.NEAR_CALL) / BR_INST_RETIRED.ALL_BRANCHES",
+        "MetricGroup": "Bad;Branches",
+        "MetricName": "Jump"
+    },
+    {
+        "BriefDescription": "Actual Average Latency for L1 data-cache miss demand load instructions (in core cycles)",
         "MetricExpr": "L1D_PEND_MISS.PENDING / ( MEM_LOAD_RETIRED.L1_MISS + MEM_LOAD_RETIRED.FB_HIT )",
-        "MetricGroup": "MemoryBound;MemoryLat",
-        "MetricName": "Load_Miss_Real_Latency"
+        "MetricGroup": "Mem;MemoryBound;MemoryLat",
+        "MetricName": "Load_Miss_Real_Latency",
+        "PublicDescription": "Actual Average Latency for L1 data-cache miss demand load instructions (in core cycles). Latency may be overestimated for multi-load instructions - e.g. repeat strings."
     },
     {
         "BriefDescription": "Memory-Level-Parallelism (average number of L1 miss demand load when there is at least one such miss. Per-Logical Processor)",
         "MetricExpr": "L1D_PEND_MISS.PENDING / L1D_PEND_MISS.PENDING_CYCLES",
-        "MetricGroup": "MemoryBound;MemoryBW",
+        "MetricGroup": "Mem;MemoryBound;MemoryBW",
         "MetricName": "MLP"
     },
     {
-        "BriefDescription": "Utilization of the core's Page Walker(s) serving STLB misses triggered by instruction/Load/Store accesses",
-        "MetricConstraint": "NO_NMI_WATCHDOG",
-        "MetricExpr": "( ITLB_MISSES.WALK_PENDING + DTLB_LOAD_MISSES.WALK_PENDING + DTLB_STORE_MISSES.WALK_PENDING + EPT.WALK_PENDING ) / ( 2 * CORE_CLKS )",
-        "MetricGroup": "MemoryTLB",
-        "MetricName": "Page_Walks_Utilization"
-    },
-    {
         "BriefDescription": "Average data fill bandwidth to the L1 data cache [GB / sec]",
         "MetricExpr": "64 * L1D.REPLACEMENT / 1000000000 / duration_time",
-        "MetricGroup": "MemoryBW",
+        "MetricGroup": "Mem;MemoryBW",
         "MetricName": "L1D_Cache_Fill_BW"
     },
     {
         "BriefDescription": "Average data fill bandwidth to the L2 cache [GB / sec]",
         "MetricExpr": "64 * L2_LINES_IN.ALL / 1000000000 / duration_time",
-        "MetricGroup": "MemoryBW",
+        "MetricGroup": "Mem;MemoryBW",
         "MetricName": "L2_Cache_Fill_BW"
     },
     {
         "BriefDescription": "Average per-core data fill bandwidth to the L3 cache [GB / sec]",
         "MetricExpr": "64 * LONGEST_LAT_CACHE.MISS / 1000000000 / duration_time",
-        "MetricGroup": "MemoryBW",
+        "MetricGroup": "Mem;MemoryBW",
         "MetricName": "L3_Cache_Fill_BW"
     },
     {
         "BriefDescription": "Average per-core data access bandwidth to the L3 cache [GB / sec]",
         "MetricExpr": "64 * OFFCORE_REQUESTS.ALL_REQUESTS / 1000000000 / duration_time",
-        "MetricGroup": "MemoryBW;Offcore",
+        "MetricGroup": "Mem;MemoryBW;Offcore",
         "MetricName": "L3_Cache_Access_BW"
     },
     {
         "BriefDescription": "L1 cache true misses per kilo instruction for retired demand loads",
         "MetricExpr": "1000 * MEM_LOAD_RETIRED.L1_MISS / INST_RETIRED.ANY",
-        "MetricGroup": "CacheMisses",
+        "MetricGroup": "Mem;CacheMisses",
         "MetricName": "L1MPKI"
     },
     {
+        "BriefDescription": "L1 cache true misses per kilo instruction for all demand loads (including speculative)",
+        "MetricExpr": "1000 * L2_RQSTS.ALL_DEMAND_DATA_RD / INST_RETIRED.ANY",
+        "MetricGroup": "Mem;CacheMisses",
+        "MetricName": "L1MPKI_Load"
+    },
+    {
         "BriefDescription": "L2 cache true misses per kilo instruction for retired demand loads",
         "MetricExpr": "1000 * MEM_LOAD_RETIRED.L2_MISS / INST_RETIRED.ANY",
-        "MetricGroup": "CacheMisses",
+        "MetricGroup": "Mem;Backend;CacheMisses",
         "MetricName": "L2MPKI"
     },
     {
         "BriefDescription": "L2 cache misses per kilo instruction for all request types (including speculative)",
         "MetricExpr": "1000 * L2_RQSTS.MISS / INST_RETIRED.ANY",
-        "MetricGroup": "CacheMisses;Offcore",
+        "MetricGroup": "Mem;CacheMisses;Offcore",
         "MetricName": "L2MPKI_All"
     },
     {
+        "BriefDescription": "L2 cache misses per kilo instruction for all demand loads  (including speculative)",
+        "MetricExpr": "1000 * L2_RQSTS.DEMAND_DATA_RD_MISS / INST_RETIRED.ANY",
+        "MetricGroup": "Mem;CacheMisses",
+        "MetricName": "L2MPKI_Load"
+    },
+    {
         "BriefDescription": "L2 cache hits per kilo instruction for all request types (including speculative)",
         "MetricExpr": "1000 * ( L2_RQSTS.REFERENCES - L2_RQSTS.MISS ) / INST_RETIRED.ANY",
-        "MetricGroup": "CacheMisses",
+        "MetricGroup": "Mem;CacheMisses",
         "MetricName": "L2HPKI_All"
     },
     {
+        "BriefDescription": "L2 cache hits per kilo instruction for all demand loads  (including speculative)",
+        "MetricExpr": "1000 * L2_RQSTS.DEMAND_DATA_RD_HIT / INST_RETIRED.ANY",
+        "MetricGroup": "Mem;CacheMisses",
+        "MetricName": "L2HPKI_Load"
+    },
+    {
         "BriefDescription": "L3 cache true misses per kilo instruction for retired demand loads",
         "MetricExpr": "1000 * MEM_LOAD_RETIRED.L3_MISS / INST_RETIRED.ANY",
-        "MetricGroup": "CacheMisses",
+        "MetricGroup": "Mem;CacheMisses",
         "MetricName": "L3MPKI"
     },
     {
+        "BriefDescription": "Fill Buffer (FB) true hits per kilo instructions for retired demand loads",
+        "MetricExpr": "1000 * MEM_LOAD_RETIRED.FB_HIT / INST_RETIRED.ANY",
+        "MetricGroup": "Mem;CacheMisses",
+        "MetricName": "FB_HPKI"
+    },
+    {
+        "BriefDescription": "Utilization of the core's Page Walker(s) serving STLB misses triggered by instruction/Load/Store accesses",
+        "MetricConstraint": "NO_NMI_WATCHDOG",
+        "MetricExpr": "( ITLB_MISSES.WALK_PENDING + DTLB_LOAD_MISSES.WALK_PENDING + DTLB_STORE_MISSES.WALK_PENDING + EPT.WALK_PENDING ) / ( 2 * CPU_CLK_UNHALTED.THREAD )",
+        "MetricGroup": "Mem;MemoryTLB",
+        "MetricName": "Page_Walks_Utilization"
+    },
+    {
+        "BriefDescription": "Utilization of the core's Page Walker(s) serving STLB misses triggered by instruction/Load/Store accesses",
+        "MetricExpr": "( ITLB_MISSES.WALK_PENDING + DTLB_LOAD_MISSES.WALK_PENDING + DTLB_STORE_MISSES.WALK_PENDING + EPT.WALK_PENDING ) / ( 2 * ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) ) )",
+        "MetricGroup": "Mem;MemoryTLB_SMT",
+        "MetricName": "Page_Walks_Utilization_SMT"
+    },
+    {
         "BriefDescription": "Rate of silent evictions from the L2 cache per Kilo instruction where the evicted lines are dropped (no writeback to L3 or memory)",
         "MetricExpr": "1000 * L2_LINES_OUT.SILENT / INST_RETIRED.ANY",
-        "MetricGroup": "L2Evicts;Server",
+        "MetricGroup": "L2Evicts;Mem;Server",
         "MetricName": "L2_Evictions_Silent_PKI"
     },
     {
         "BriefDescription": "Rate of non silent evictions from the L2 cache per Kilo instruction",
         "MetricExpr": "1000 * L2_LINES_OUT.NON_SILENT / INST_RETIRED.ANY",
-        "MetricGroup": "L2Evicts;Server",
+        "MetricGroup": "L2Evicts;Mem;Server",
         "MetricName": "L2_Evictions_NonSilent_PKI"
     },
     {
@@ -219,7 +532,7 @@
     {
         "BriefDescription": "Giga Floating Point Operations Per Second",
         "MetricExpr": "( ( 1 * ( FP_ARITH_INST_RETIRED.SCALAR_SINGLE + FP_ARITH_INST_RETIRED.SCALAR_DOUBLE ) + 2 * FP_ARITH_INST_RETIRED.128B_PACKED_DOUBLE + 4 * ( FP_ARITH_INST_RETIRED.128B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.256B_PACKED_DOUBLE ) + 8 * ( FP_ARITH_INST_RETIRED.256B_PACKED_SINGLE + FP_ARITH_INST_RETIRED.512B_PACKED_DOUBLE ) + 16 * FP_ARITH_INST_RETIRED.512B_PACKED_SINGLE ) / 1000000000 ) / duration_time",
-        "MetricGroup": "Flops;HPC",
+        "MetricGroup": "Cor;Flops;HPC",
         "MetricName": "GFLOPs"
     },
     {
@@ -229,6 +542,48 @@
         "MetricName": "Turbo_Utilization"
     },
     {
+        "BriefDescription": "Fraction of Core cycles where the core was running with power-delivery for baseline license level 0",
+        "MetricExpr": "CORE_POWER.LVL0_TURBO_LICENSE / CPU_CLK_UNHALTED.THREAD",
+        "MetricGroup": "Power",
+        "MetricName": "Power_License0_Utilization",
+        "PublicDescription": "Fraction of Core cycles where the core was running with power-delivery for baseline license level 0.  This includes non-AVX codes, SSE, AVX 128-bit, and low-current AVX 256-bit codes."
+    },
+    {
+        "BriefDescription": "Fraction of Core cycles where the core was running with power-delivery for baseline license level 0. SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "CORE_POWER.LVL0_TURBO_LICENSE / 2 / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )",
+        "MetricGroup": "Power_SMT",
+        "MetricName": "Power_License0_Utilization_SMT",
+        "PublicDescription": "Fraction of Core cycles where the core was running with power-delivery for baseline license level 0.  This includes non-AVX codes, SSE, AVX 128-bit, and low-current AVX 256-bit codes. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
+        "BriefDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 1",
+        "MetricExpr": "CORE_POWER.LVL1_TURBO_LICENSE / CPU_CLK_UNHALTED.THREAD",
+        "MetricGroup": "Power",
+        "MetricName": "Power_License1_Utilization",
+        "PublicDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 1.  This includes high current AVX 256-bit instructions as well as low current AVX 512-bit instructions."
+    },
+    {
+        "BriefDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 1. SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "CORE_POWER.LVL1_TURBO_LICENSE / 2 / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )",
+        "MetricGroup": "Power_SMT",
+        "MetricName": "Power_License1_Utilization_SMT",
+        "PublicDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 1.  This includes high current AVX 256-bit instructions as well as low current AVX 512-bit instructions. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
+        "BriefDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 2 (introduced in SKX)",
+        "MetricExpr": "CORE_POWER.LVL2_TURBO_LICENSE / CPU_CLK_UNHALTED.THREAD",
+        "MetricGroup": "Power",
+        "MetricName": "Power_License2_Utilization",
+        "PublicDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 2 (introduced in SKX).  This includes high current AVX 512-bit instructions."
+    },
+    {
+        "BriefDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 2 (introduced in SKX). SMT version; use when SMT is enabled and measuring per logical CPU.",
+        "MetricExpr": "CORE_POWER.LVL2_TURBO_LICENSE / 2 / ( ( CPU_CLK_UNHALTED.THREAD / 2 ) * ( 1 + CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / CPU_CLK_UNHALTED.REF_XCLK ) )",
+        "MetricGroup": "Power_SMT",
+        "MetricName": "Power_License2_Utilization_SMT",
+        "PublicDescription": "Fraction of Core cycles where the core was running with power-delivery for license level 2 (introduced in SKX).  This includes high current AVX 512-bit instructions. SMT version; use when SMT is enabled and measuring per logical CPU."
+    },
+    {
         "BriefDescription": "Fraction of cycles where both hardware Logical Processors were active",
         "MetricExpr": "1 - CPU_CLK_UNHALTED.ONE_THREAD_ACTIVE / ( CPU_CLK_UNHALTED.REF_XCLK_ANY / 2 ) if #SMT_on else 0",
         "MetricGroup": "SMT",
@@ -241,33 +596,45 @@
         "MetricName": "Kernel_Utilization"
     },
     {
+        "BriefDescription": "Cycles Per Instruction for the Operating System (OS) Kernel mode",
+        "MetricExpr": "CPU_CLK_UNHALTED.THREAD_P:k / INST_RETIRED.ANY_P:k",
+        "MetricGroup": "OS",
+        "MetricName": "Kernel_CPI"
+    },
+    {
         "BriefDescription": "Average external Memory Bandwidth Use for reads and writes [GB / sec]",
         "MetricExpr": "( 64 * ( uncore_imc@cas_count_read@ + uncore_imc@cas_count_write@ ) / 1000000000 ) / duration_time",
-        "MetricGroup": "HPC;MemoryBW;SoC",
+        "MetricGroup": "HPC;Mem;MemoryBW;SoC",
         "MetricName": "DRAM_BW_Use"
     },
     {
         "BriefDescription": "Average latency of data read request to external memory (in nanoseconds). Accounts for demand loads and L1/L2 prefetches",
         "MetricExpr": "1000000000 * ( cha@event\\=0x36\\,umask\\=0x21\\,config\\=0x40433@ / cha@event\\=0x35\\,umask\\=0x21\\,config\\=0x40433@ ) / ( cha_0@event\\=0x0@ / duration_time )",
-        "MetricGroup": "MemoryLat;SoC",
+        "MetricGroup": "Mem;MemoryLat;SoC",
         "MetricName": "MEM_Read_Latency"
     },
     {
         "BriefDescription": "Average number of parallel data read requests to external memory. Accounts for demand loads and L1/L2 prefetches",
         "MetricExpr": "cha@event\\=0x36\\,umask\\=0x21\\,config\\=0x40433@ / cha@event\\=0x36\\,umask\\=0x21\\,config\\=0x40433\\,thresh\\=1@",
-        "MetricGroup": "MemoryBW;SoC",
+        "MetricGroup": "Mem;MemoryBW;SoC",
         "MetricName": "MEM_Parallel_Reads"
     },
     {
+        "BriefDescription": "Average latency of data read request to external DRAM memory [in nanoseconds]. Accounts for demand loads and L1/L2 data-read prefetches",
+        "MetricExpr": "1000000000 * ( UNC_M_RPQ_OCCUPANCY / UNC_M_RPQ_INSERTS ) / imc_0@event\\=0x0@",
+        "MetricGroup": "Mem;MemoryLat;SoC;Server",
+        "MetricName": "MEM_DRAM_Read_Latency"
+    },
+    {
         "BriefDescription": "Average IO (network or disk) Bandwidth Use for Writes [GB / sec]",
         "MetricExpr": "( UNC_IIO_DATA_REQ_OF_CPU.MEM_READ.PART0 + UNC_IIO_DATA_REQ_OF_CPU.MEM_READ.PART1 + UNC_IIO_DATA_REQ_OF_CPU.MEM_READ.PART2 + UNC_IIO_DATA_REQ_OF_CPU.MEM_READ.PART3 ) * 4 / 1000000000 / duration_time",
-        "MetricGroup": "IoBW;SoC;Server",
+        "MetricGroup": "IoBW;Mem;SoC;Server",
         "MetricName": "IO_Write_BW"
     },
     {
         "BriefDescription": "Average IO (network or disk) Bandwidth Use for Reads [GB / sec]",
         "MetricExpr": "( UNC_IIO_DATA_REQ_OF_CPU.MEM_WRITE.PART0 + UNC_IIO_DATA_REQ_OF_CPU.MEM_WRITE.PART1 + UNC_IIO_DATA_REQ_OF_CPU.MEM_WRITE.PART2 + UNC_IIO_DATA_REQ_OF_CPU.MEM_WRITE.PART3 ) * 4 / 1000000000 / duration_time",
-        "MetricGroup": "IoBW;SoC;Server",
+        "MetricGroup": "IoBW;Mem;SoC;Server",
         "MetricName": "IO_Read_BW"
     },
     {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/arch/x86/skylakex/uncore-other.json
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/arch/x86/skylakex/uncore-other.json
@@ -538,6 +538,18 @@
         "Unit": "IIO"
     },
     {
+        "BriefDescription": "PCIe Completion Buffer Inserts of completions with data: Part 0-3",
+        "Counter": "0,1,2,3",
+        "EventCode": "0xC2",
+        "EventName": "UNC_IIO_COMP_BUF_INSERTS.CMPD.ALL_PARTS",
+        "FCMask": "0x4",
+        "PerPkg": "1",
+        "PortMask": "0x0f",
+        "PublicDescription": "PCIe Completion Buffer Inserts of completions with data: Part 0-3",
+        "UMask": "0x03",
+        "Unit": "IIO"
+    },
+    {
         "BriefDescription": "PCIe Completion Buffer Inserts of completions with data: Part 0",
         "Counter": "0,1,2,3",
         "EventCode": "0xC2",
@@ -586,6 +598,17 @@
         "Unit": "IIO"
     },
     {
+        "BriefDescription": "PCIe Completion Buffer occupancy of completions with data: Part 0-3",
+        "Counter": "2,3",
+        "EventCode": "0xD5",
+        "EventName": "UNC_IIO_COMP_BUF_OCCUPANCY.CMPD.ALL_PARTS",
+        "FCMask": "0x04",
+        "PerPkg": "1",
+        "PublicDescription": "PCIe Completion Buffer occupancy of completions with data: Part 0-3",
+        "UMask": "0x0f",
+        "Unit": "IIO"
+    },
+    {
         "BriefDescription": "PCIe Completion Buffer occupancy of completions with data: Part 0",
         "Counter": "2,3",
         "EventCode": "0xD5",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/pmu-events/jevents.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/pmu-events/jevents.c
@@ -604,7 +604,7 @@
 			} else if (json_streq(map, field, "ExtSel")) {
 				char *code = NULL;
 				addfield(map, &code, "", "", val);
-				eventcode |= strtoul(code, NULL, 0) << 21;
+				eventcode |= strtoul(code, NULL, 0) << 8;
 				free(code);
 			} else if (json_streq(map, field, "EventName")) {
 				addfield(map, &je.name, "", "", val);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/scripts/python/intel-pt-events.py
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/scripts/python/intel-pt-events.py
@@ -11,7 +11,7 @@
 # FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 # more details.
 
-from __future__ import print_function
+from __future__ import division, print_function
 
 import os
 import sys
@@ -32,8 +32,7 @@
 except:
 	broken_pipe_exception = IOError
 
-glb_switch_str		= None
-glb_switch_printed	= True
+glb_switch_str		= {}
 glb_insn		= False
 glb_disassembler	= None
 glb_src			= False
@@ -70,6 +69,7 @@
 	ap = argparse.ArgumentParser(usage = "", add_help = False)
 	ap.add_argument("--insn-trace", action='store_true')
 	ap.add_argument("--src-trace", action='store_true')
+	ap.add_argument("--all-switch-events", action='store_true')
 	global glb_args
 	global glb_insn
 	global glb_src
@@ -256,10 +256,6 @@
 	print(start_str, src_str)
 
 def do_process_event(param_dict):
-	global glb_switch_printed
-	if not glb_switch_printed:
-		print(glb_switch_str)
-		glb_switch_printed = True
 	event_attr = param_dict["attr"]
 	sample	   = param_dict["sample"]
 	raw_buf	   = param_dict["raw_buf"]
@@ -274,6 +270,11 @@
 	dso    = get_optional(param_dict, "dso")
 	symbol = get_optional(param_dict, "symbol")
 
+	cpu = sample["cpu"]
+	if cpu in glb_switch_str:
+		print(glb_switch_str[cpu])
+		del glb_switch_str[cpu]
+
 	if name[0:12] == "instructions":
 		if glb_src:
 			print_srccode(comm, param_dict, sample, symbol, dso, True)
@@ -336,8 +337,6 @@
 		sys.exit(1)
 
 def context_switch(ts, cpu, pid, tid, np_pid, np_tid, machine_pid, out, out_preempt, *x):
-	global glb_switch_printed
-	global glb_switch_str
 	if out:
 		out_str = "Switch out "
 	else:
@@ -350,6 +349,10 @@
 		machine_str = ""
 	else:
 		machine_str = "machine PID %d" % machine_pid
-	glb_switch_str = "%16s %5d/%-5d [%03u] %9u.%09u %5d/%-5d %s %s" % \
+	switch_str = "%16s %5d/%-5d [%03u] %9u.%09u %5d/%-5d %s %s" % \
 		(out_str, pid, tid, cpu, ts / 1000000000, ts %1000000000, np_pid, np_tid, machine_str, preempt_str)
-	glb_switch_printed = False
+	if glb_args.all_switch_events:
+		print(switch_str);
+	else:
+		global glb_switch_str
+		glb_switch_str[cpu] = switch_str
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/tests/builtin-test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/tests/builtin-test.c
@@ -828,6 +828,9 @@
         if (ret < 0)
                 return ret;
 
+	/* Unbuffered output */
+	setvbuf(stdout, NULL, _IONBF, 0);
+
 	argc = parse_options_subcommand(argc, argv, test_options, test_subcommands, test_usage, 0);
 	if (argc >= 1 && !strcmp(argv[0], "list"))
 		return perf_test__list(argc - 1, argv + 1);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/tests/perf-time-to-tsc.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/tests/perf-time-to-tsc.c
@@ -20,8 +20,6 @@
 #include "tsc.h"
 #include "mmap.h"
 #include "tests.h"
-#include "pmu.h"
-#include "pmu-hybrid.h"
 
 #define CHECK__(x) {				\
 	while ((x) < 0) {			\
@@ -84,18 +82,8 @@
 
 	evlist__config(evlist, &opts, NULL);
 
-	evsel = evlist__first(evlist);
-
-	evsel->core.attr.comm = 1;
-	evsel->core.attr.disabled = 1;
-	evsel->core.attr.enable_on_exec = 0;
-
-	/*
-	 * For hybrid "cycles:u", it creates two events.
-	 * Init the second evsel here.
-	 */
-	if (perf_pmu__has_hybrid() && perf_pmu__hybrid_mounted("cpu_atom")) {
-		evsel = evsel__next(evsel);
+	/* For hybrid "cycles:u", it creates two events */
+	evlist__for_each_entry(evlist, evsel) {
 		evsel->core.attr.comm = 1;
 		evsel->core.attr.disabled = 1;
 		evsel->core.attr.enable_on_exec = 0;
@@ -141,10 +129,12 @@
 				goto next_event;
 
 			if (strcmp(event->comm.comm, comm1) == 0) {
+				CHECK_NOT_NULL__(evsel = evlist__event2evsel(evlist, event));
 				CHECK__(evsel__parse_sample(evsel, event, &sample));
 				comm1_time = sample.time;
 			}
 			if (strcmp(event->comm.comm, comm2) == 0) {
+				CHECK_NOT_NULL__(evsel = evlist__event2evsel(evlist, event));
 				CHECK__(evsel__parse_sample(evsel, event, &sample));
 				comm2_time = sample.time;
 			}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/tests/shell/record+zstd_comp_decomp.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/tests/shell/record+zstd_comp_decomp.sh
@@ -12,7 +12,7 @@
 
 collect_z_record() {
 	echo "Collecting compressed record file:"
-	[[ "$(uname -m)" != s390x ]] && gflag='-g'
+	[ "$(uname -m)" != s390x ] && gflag='-g'
 	$perf_tool record -o $trace_file $gflag -z -F 5000 -- \
 		dd count=500 if=/dev/urandom of=/dev/null
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/tests/shell/stat_bpf_counters.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/tests/shell/stat_bpf_counters.sh
@@ -22,10 +22,10 @@
 }
 
 # skip if --bpf-counters is not supported
-if ! perf stat --bpf-counters true > /dev/null 2>&1; then
-	if [ "$1" == "-v" ]; then
+if ! perf stat -e cycles --bpf-counters true > /dev/null 2>&1; then
+	if [ "$1" = "-v" ]; then
 		echo "Skipping: --bpf-counters not supported"
-		perf --no-pager stat --bpf-counters true || true
+		perf --no-pager stat -e cycles --bpf-counters true || true
 	fi
 	exit 2
 fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/tests/shell/test_uprobe_from_different_cu.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/tests/shell/test_uprobe_from_different_cu.sh
@@ -0,0 +1,83 @@
+#!/bin/bash
+# test perf probe of function from different CU
+# SPDX-License-Identifier: GPL-2.0
+
+set -e
+
+# skip if there's no gcc
+if ! [ -x "$(command -v gcc)" ]; then
+        echo "failed: no gcc compiler"
+        exit 2
+fi
+
+temp_dir=$(mktemp -d /tmp/perf-uprobe-different-cu-sh.XXXXXXXXXX)
+
+cleanup()
+{
+	trap - EXIT TERM INT
+	if [[ "${temp_dir}" =~ ^/tmp/perf-uprobe-different-cu-sh.*$ ]]; then
+		echo "--- Cleaning up ---"
+		perf probe -x ${temp_dir}/testfile -d foo || true
+		rm -f "${temp_dir}/"*
+		rmdir "${temp_dir}"
+	fi
+}
+
+trap_cleanup()
+{
+        cleanup
+        exit 1
+}
+
+trap trap_cleanup EXIT TERM INT
+
+cat > ${temp_dir}/testfile-foo.h << EOF
+struct t
+{
+  int *p;
+  int c;
+};
+
+extern int foo (int i, struct t *t);
+EOF
+
+cat > ${temp_dir}/testfile-foo.c << EOF
+#include "testfile-foo.h"
+
+int
+foo (int i, struct t *t)
+{
+  int j, res = 0;
+  for (j = 0; j < i && j < t->c; j++)
+    res += t->p[j];
+
+  return res;
+}
+EOF
+
+cat > ${temp_dir}/testfile-main.c << EOF
+#include "testfile-foo.h"
+
+static struct t g;
+
+int
+main (int argc, char **argv)
+{
+  int i;
+  int j[argc];
+  g.c = argc;
+  g.p = j;
+  for (i = 0; i < argc; i++)
+    j[i] = (int) argv[i][0];
+  return foo (3, &g);
+}
+EOF
+
+gcc -g -Og -flto -c ${temp_dir}/testfile-foo.c -o ${temp_dir}/testfile-foo.o
+gcc -g -Og -c ${temp_dir}/testfile-main.c -o ${temp_dir}/testfile-main.o
+gcc -g -Og -o ${temp_dir}/testfile ${temp_dir}/testfile-foo.o ${temp_dir}/testfile-main.o
+
+perf probe -x ${temp_dir}/testfile --funcs foo
+perf probe -x ${temp_dir}/testfile foo
+
+cleanup
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/tests/switch-tracking.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/tests/switch-tracking.c
@@ -324,6 +324,7 @@
 int test__switch_tracking(struct test *test __maybe_unused, int subtest __maybe_unused)
 {
 	const char *sched_switch = "sched:sched_switch";
+	const char *cycles = "cycles:u";
 	struct switch_tracking switch_tracking = { .tids = NULL, };
 	struct record_opts opts = {
 		.mmap_pages	     = UINT_MAX,
@@ -372,12 +373,19 @@
 	cpu_clocks_evsel = evlist__last(evlist);
 
 	/* Second event */
-	if (perf_pmu__has_hybrid())
-		err = parse_events(evlist, "cpu_core/cycles/u", NULL);
-	else
-		err = parse_events(evlist, "cycles:u", NULL);
+	if (perf_pmu__has_hybrid()) {
+		cycles = "cpu_core/cycles/u";
+		err = parse_events(evlist, cycles, NULL);
+		if (err) {
+			cycles = "cpu_atom/cycles/u";
+			pr_debug("Trying %s\n", cycles);
+			err = parse_events(evlist, cycles, NULL);
+		}
+	} else {
+		err = parse_events(evlist, cycles, NULL);
+	}
 	if (err) {
-		pr_debug("Failed to parse event cycles:u\n");
+		pr_debug("Failed to parse event %s\n", cycles);
 		goto out_err;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/trace/beauty/include/linux/socket.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/trace/beauty/include/linux/socket.h
@@ -364,6 +364,8 @@
 #define SOL_KCM		281
 #define SOL_TLS		282
 #define SOL_XDP		283
+#define SOL_MPTCP	284
+#define SOL_MCTP	285
 
 /* IPX options */
 #define IPX_TYPE	1
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/ui/browsers/annotate.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/ui/browsers/annotate.c
@@ -966,6 +966,7 @@
 		.opts = opts,
 	};
 	int ret = -1, err;
+	int not_annotated = list_empty(&notes->src->source);
 
 	if (sym == NULL)
 		return -1;
@@ -973,13 +974,15 @@
 	if (ms->map->dso->annotate_warned)
 		return -1;
 
-	err = symbol__annotate2(ms, evsel, opts, &browser.arch);
-	if (err) {
-		char msg[BUFSIZ];
-		ms->map->dso->annotate_warned = true;
-		symbol__strerror_disassemble(ms, err, msg, sizeof(msg));
-		ui__error("Couldn't annotate %s:\n%s", sym->name, msg);
-		goto out_free_offsets;
+	if (not_annotated) {
+		err = symbol__annotate2(ms, evsel, opts, &browser.arch);
+		if (err) {
+			char msg[BUFSIZ];
+			ms->map->dso->annotate_warned = true;
+			symbol__strerror_disassemble(ms, err, msg, sizeof(msg));
+			ui__error("Couldn't annotate %s:\n%s", sym->name, msg);
+			goto out_free_offsets;
+		}
 	}
 
 	ui_helpline__push("Press ESC to exit");
@@ -994,9 +997,11 @@
 
 	ret = annotate_browser__run(&browser, evsel, hbt);
 
-	annotated_source__purge(notes->src);
+	if(not_annotated)
+		annotated_source__purge(notes->src);
 
 out_free_offsets:
-	zfree(&notes->offsets);
+	if(not_annotated)
+		zfree(&notes->offsets);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/ui/browsers/hists.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/ui/browsers/hists.c
@@ -407,11 +407,6 @@
 	return container_of(ms, struct callchain_list, ms)->has_children;
 }
 
-static bool hist_browser__he_selection_unfolded(struct hist_browser *browser)
-{
-	return browser->he_selection ? browser->he_selection->unfolded : false;
-}
-
 static bool hist_browser__selection_unfolded(struct hist_browser *browser)
 {
 	struct hist_entry *he = browser->he_selection;
@@ -584,8 +579,8 @@
 	return n;
 }
 
-static void __hist_entry__set_folding(struct hist_entry *he,
-				      struct hist_browser *hb, bool unfold)
+static void hist_entry__set_folding(struct hist_entry *he,
+				    struct hist_browser *hb, bool unfold)
 {
 	hist_entry__init_have_children(he);
 	he->unfolded = unfold ? he->has_children : false;
@@ -603,34 +598,12 @@
 		he->nr_rows = 0;
 }
 
-static void hist_entry__set_folding(struct hist_entry *he,
-				    struct hist_browser *browser, bool unfold)
-{
-	double percent;
-
-	percent = hist_entry__get_percent_limit(he);
-	if (he->filtered || percent < browser->min_pcnt)
-		return;
-
-	__hist_entry__set_folding(he, browser, unfold);
-
-	if (!he->depth || unfold)
-		browser->nr_hierarchy_entries++;
-	if (he->leaf)
-		browser->nr_callchain_rows += he->nr_rows;
-	else if (unfold && !hist_entry__has_hierarchy_children(he, browser->min_pcnt)) {
-		browser->nr_hierarchy_entries++;
-		he->has_no_entry = true;
-		he->nr_rows = 1;
-	} else
-		he->has_no_entry = false;
-}
-
 static void
 __hist_browser__set_folding(struct hist_browser *browser, bool unfold)
 {
 	struct rb_node *nd;
 	struct hist_entry *he;
+	double percent;
 
 	nd = rb_first_cached(&browser->hists->entries);
 	while (nd) {
@@ -640,6 +613,21 @@
 		nd = __rb_hierarchy_next(nd, HMD_FORCE_CHILD);
 
 		hist_entry__set_folding(he, browser, unfold);
+
+		percent = hist_entry__get_percent_limit(he);
+		if (he->filtered || percent < browser->min_pcnt)
+			continue;
+
+		if (!he->depth || unfold)
+			browser->nr_hierarchy_entries++;
+		if (he->leaf)
+			browser->nr_callchain_rows += he->nr_rows;
+		else if (unfold && !hist_entry__has_hierarchy_children(he, browser->min_pcnt)) {
+			browser->nr_hierarchy_entries++;
+			he->has_no_entry = true;
+			he->nr_rows = 1;
+		} else
+			he->has_no_entry = false;
 	}
 }
 
@@ -659,8 +647,10 @@
 	if (!browser->he_selection)
 		return;
 
-	hist_entry__set_folding(browser->he_selection, browser, unfold);
-	browser->b.nr_entries = hist_browser__nr_entries(browser);
+	if (unfold == browser->he_selection->unfolded)
+		return;
+
+	hist_browser__toggle_fold(browser);
 }
 
 static void ui_browser__warn_lost_events(struct ui_browser *browser)
@@ -732,8 +722,8 @@
 		hist_browser__set_folding(browser, true);
 		break;
 	case 'e':
-		/* Expand the selected entry. */
-		hist_browser__set_folding_selected(browser, !hist_browser__he_selection_unfolded(browser));
+		/* Toggle expand/collapse the selected entry. */
+		hist_browser__toggle_fold(browser);
 		break;
 	case 'H':
 		browser->show_headers = !browser->show_headers;
@@ -1779,7 +1769,7 @@
 	hists_browser__scnprintf_hierarchy_headers(browser, headers,
 						   sizeof(headers));
 
-	ui_browser__gotorc(&browser->b, 0, 0);
+	ui_browser__gotorc_title(&browser->b, 0, 0);
 	ui_browser__set_color(&browser->b, HE_COLORSET_ROOT);
 	ui_browser__write_nstring(&browser->b, headers, browser->b.width + 1);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/ui/hist.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/ui/hist.c
@@ -535,6 +535,18 @@
 #undef __HPP_SORT_ACC_FN
 #undef __HPP_SORT_RAW_FN
 
+static void fmt_free(struct perf_hpp_fmt *fmt)
+{
+	/*
+	 * At this point fmt should be completely
+	 * unhooked, if not it's a bug.
+	 */
+	BUG_ON(!list_empty(&fmt->list));
+	BUG_ON(!list_empty(&fmt->sort_list));
+
+	if (fmt->free)
+		fmt->free(fmt);
+}
 
 void perf_hpp__init(void)
 {
@@ -598,9 +610,10 @@
 	list_add(&format->sort_list, &list->sorts);
 }
 
-void perf_hpp__column_unregister(struct perf_hpp_fmt *format)
+static void perf_hpp__column_unregister(struct perf_hpp_fmt *format)
 {
 	list_del_init(&format->list);
+	fmt_free(format);
 }
 
 void perf_hpp__cancel_cumulate(void)
@@ -672,19 +685,6 @@
 }
 
 
-static void fmt_free(struct perf_hpp_fmt *fmt)
-{
-	/*
-	 * At this point fmt should be completely
-	 * unhooked, if not it's a bug.
-	 */
-	BUG_ON(!list_empty(&fmt->list));
-	BUG_ON(!list_empty(&fmt->sort_list));
-
-	if (fmt->free)
-		fmt->free(fmt);
-}
-
 void perf_hpp__reset_output_field(struct perf_hpp_list *list)
 {
 	struct perf_hpp_fmt *fmt, *tmp;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/Build
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/Build
@@ -263,6 +263,12 @@
 else
   bison_flags += -w
 endif
+
+BISON_LT_381 := $(shell expr $(shell $(BISON) --version | grep bison | sed -e 's/.\+ \([0-9]\+\).\([0-9]\+\).\([0-9]\+\)/\1\2\3/g') \< 381)
+ifeq ($(BISON_LT_381),1)
+  bison_flags += -DYYNOMEM=YYABORT
+endif
+
 CFLAGS_parse-events-bison.o += $(bison_flags)
 CFLAGS_pmu-bison.o          += -DYYLTYPE_IS_TRIVIAL=0 $(bison_flags)
 CFLAGS_expr-bison.o         += -DYYLTYPE_IS_TRIVIAL=0 $(bison_flags)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/annotate.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/annotate.c
@@ -1694,6 +1694,7 @@
 #include <bpf/btf.h>
 #include <bpf/libbpf.h>
 #include <linux/btf.h>
+#include <tools/dis-asm-compat.h>
 
 static int symbol__disassemble_bpf(struct symbol *sym,
 				   struct annotate_args *args)
@@ -1728,17 +1729,20 @@
 	perf_exe(tpath, sizeof(tpath));
 
 	bfdf = bfd_openr(tpath, NULL);
-	assert(bfdf);
-	assert(bfd_check_format(bfdf, bfd_object));
+	if (bfdf == NULL)
+		abort();
+
+	if (!bfd_check_format(bfdf, bfd_object))
+		abort();
 
 	s = open_memstream(&buf, &buf_size);
 	if (!s) {
 		ret = errno;
 		goto out;
 	}
-	init_disassemble_info(&info, s,
-			      (fprintf_ftype) fprintf);
-
+	init_disassemble_info_compat(&info, s,
+				     (fprintf_ftype) fprintf,
+				     fprintf_styled);
 	info.arch = bfd_get_arch(bfdf);
 	info.mach = bfd_get_mach(bfdf);
 
@@ -1777,7 +1781,8 @@
 #else
 	disassemble = disassembler(bfdf);
 #endif
-	assert(disassemble);
+	if (disassemble == NULL)
+		abort();
 
 	fflush(s);
 	do {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/arm-spe.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/arm-spe.c
@@ -51,6 +51,7 @@
 	u8				timeless_decoding;
 	u8				data_queued;
 
+	u64				sample_type;
 	u8				sample_flc;
 	u8				sample_llc;
 	u8				sample_tlb;
@@ -248,6 +249,12 @@
 	event->sample.header.size = sizeof(struct perf_event_header);
 }
 
+static int arm_spe__inject_event(union perf_event *event, struct perf_sample *sample, u64 type)
+{
+	event->header.size = perf_event__sample_event_size(sample, type, 0);
+	return perf_event__synthesize_sample(event, type, 0, sample);
+}
+
 static inline int
 arm_spe_deliver_synth_event(struct arm_spe *spe,
 			    struct arm_spe_queue *speq __maybe_unused,
@@ -256,6 +263,12 @@
 {
 	int ret;
 
+	if (spe->synth_opts.inject) {
+		ret = arm_spe__inject_event(event, sample, spe->sample_type);
+		if (ret)
+			return ret;
+	}
+
 	ret = perf_session__deliver_synth_event(spe->session, event, sample);
 	if (ret)
 		pr_err("ARM SPE: failed to deliver event, error %d\n", ret);
@@ -299,26 +312,16 @@
 	return arm_spe_deliver_synth_event(spe, speq, event, &sample);
 }
 
-#define SPE_MEM_TYPE	(ARM_SPE_L1D_ACCESS | ARM_SPE_L1D_MISS | \
-			 ARM_SPE_LLC_ACCESS | ARM_SPE_LLC_MISS | \
-			 ARM_SPE_REMOTE_ACCESS)
-
-static bool arm_spe__is_memory_event(enum arm_spe_sample_type type)
-{
-	if (type & SPE_MEM_TYPE)
-		return true;
-
-	return false;
-}
-
 static u64 arm_spe__synth_data_source(const struct arm_spe_record *record)
 {
 	union perf_mem_data_src	data_src = { 0 };
 
 	if (record->op == ARM_SPE_LD)
 		data_src.mem_op = PERF_MEM_OP_LOAD;
-	else
+	else if (record->op == ARM_SPE_ST)
 		data_src.mem_op = PERF_MEM_OP_STORE;
+	else
+		return 0;
 
 	if (record->type & (ARM_SPE_LLC_ACCESS | ARM_SPE_LLC_MISS)) {
 		data_src.mem_lvl = PERF_MEM_LVL_L3;
@@ -422,7 +425,11 @@
 			return err;
 	}
 
-	if (spe->sample_memory && arm_spe__is_memory_event(record->type)) {
+	/*
+	 * When data_src is zero it means the record is not a memory operation,
+	 * skip to synthesize memory sample for this case.
+	 */
+	if (spe->sample_memory && data_src) {
 		err = arm_spe__synth_mem_sample(speq, spe->memory_id, data_src);
 		if (err)
 			return err;
@@ -914,12 +921,15 @@
 	attr.type = PERF_TYPE_HARDWARE;
 	attr.sample_type = evsel->core.attr.sample_type & PERF_SAMPLE_MASK;
 	attr.sample_type |= PERF_SAMPLE_IP | PERF_SAMPLE_TID |
-			    PERF_SAMPLE_PERIOD | PERF_SAMPLE_DATA_SRC;
+			    PERF_SAMPLE_PERIOD | PERF_SAMPLE_DATA_SRC |
+			    PERF_SAMPLE_ADDR;
 	if (spe->timeless_decoding)
 		attr.sample_type &= ~(u64)PERF_SAMPLE_TIME;
 	else
 		attr.sample_type |= PERF_SAMPLE_TIME;
 
+	spe->sample_type = attr.sample_type;
+
 	attr.exclude_user = evsel->core.attr.exclude_user;
 	attr.exclude_kernel = evsel->core.attr.exclude_kernel;
 	attr.exclude_hv = evsel->core.attr.exclude_hv;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/auxtrace.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/auxtrace.c
@@ -1107,6 +1107,9 @@
 	if (auxtrace__dont_decode(session))
 		return 0;
 
+	if (perf_data__is_pipe(session->data))
+		return 0;
+
 	if (!session->auxtrace || !session->auxtrace->queue_data)
 		return -EINVAL;
 
@@ -2260,11 +2263,19 @@
 	bool		near;
 };
 
+static bool kern_sym_name_match(const char *kname, const char *name)
+{
+	size_t n = strlen(name);
+
+	return !strcmp(kname, name) ||
+	       (!strncmp(kname, name, n) && kname[n] == '\t');
+}
+
 static bool kern_sym_match(struct sym_args *args, const char *name, char type)
 {
 	/* A function with the same name, and global or the n'th found or any */
 	return kallsyms__is_function(type) &&
-	       !strcmp(name, args->name) &&
+	       kern_sym_name_match(name, args->name) &&
 	       ((args->global && isupper(type)) ||
 		(args->selected && ++(args->cnt) == args->idx) ||
 		(!args->global && !args->selected));
@@ -2367,6 +2378,7 @@
 			       char type, u64 start)
 {
 	struct sym_args *args = arg;
+	u64 size;
 
 	if (!kallsyms__is_function(type))
 		return 0;
@@ -2376,7 +2388,9 @@
 		args->start = start;
 	}
 	/* Don't know exactly where the kernel ends, so we add a page */
-	args->size = round_up(start, page_size) + page_size - args->start;
+	size = round_up(start, page_size) + page_size - args->start;
+	if (size > args->size)
+		args->size = size;
 
 	return 0;
 }
@@ -2537,7 +2551,7 @@
 				*size = sym->start - *start;
 			if (idx > 0) {
 				if (*size)
-					return 1;
+					return 0;
 			} else if (dso_sym_match(sym, sym_name, &cnt, idx)) {
 				print_duplicate_syms(dso, sym_name);
 				return -EINVAL;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf-event.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf-event.c
@@ -21,7 +21,8 @@
 #include "record.h"
 #include "util/synthetic-events.h"
 
-struct btf * __weak btf__load_from_kernel_by_id(__u32 id)
+#ifndef HAVE_LIBBPF_BTF__LOAD_FROM_KERNEL_BY_ID
+struct btf *btf__load_from_kernel_by_id(__u32 id)
 {
        struct btf *btf;
 #pragma GCC diagnostic push
@@ -31,6 +32,7 @@
 
        return err ? ERR_PTR(err) : btf;
 }
+#endif
 
 #define ptr_to_u64(ptr)    ((__u64)(unsigned long)(ptr))
 
@@ -120,7 +122,11 @@
 	node->data_size = data_size;
 	memcpy(node->data, data, data_size);
 
-	perf_env__insert_btf(env, node);
+	if (!perf_env__insert_btf(env, node)) {
+		/* Insertion failed because of a duplicate. */
+		free(node);
+		return -1;
+	}
 	return 0;
 }
 
@@ -294,7 +300,10 @@
 		}
 
 		info_node->info_linear = info_linear;
-		perf_env__insert_bpf_prog_info(env, info_node);
+		if (!perf_env__insert_bpf_prog_info(env, info_node)) {
+			free(info_linear);
+			free(info_node);
+		}
 		info_linear = NULL;
 
 		/*
@@ -482,7 +491,10 @@
 	info_node = malloc(sizeof(struct bpf_prog_info_node));
 	if (info_node) {
 		info_node->info_linear = info_linear;
-		perf_env__insert_bpf_prog_info(env, info_node);
+		if (!perf_env__insert_bpf_prog_info(env, info_node)) {
+			free(info_linear);
+			free(info_node);
+		}
 	} else
 		free(info_linear);
 
@@ -548,9 +560,9 @@
 	return evlist__add_sb_event(evlist, &attr, bpf_event__sb_cb, env);
 }
 
-void bpf_event__print_bpf_prog_info(struct bpf_prog_info *info,
-				    struct perf_env *env,
-				    FILE *fp)
+void __bpf_event__print_bpf_prog_info(struct bpf_prog_info *info,
+				      struct perf_env *env,
+				      FILE *fp)
 {
 	__u32 *prog_lens = (__u32 *)(uintptr_t)(info->jited_func_lens);
 	__u64 *prog_addrs = (__u64 *)(uintptr_t)(info->jited_ksyms);
@@ -566,7 +578,7 @@
 	if (info->btf_id) {
 		struct btf_node *node;
 
-		node = perf_env__find_btf(env, info->btf_id);
+		node = __perf_env__find_btf(env, info->btf_id);
 		if (node)
 			btf = btf__new((__u8 *)(node->data),
 				       node->data_size);
@@ -576,7 +588,7 @@
 		synthesize_bpf_prog_name(name, KSYM_NAME_LEN, info, btf, 0);
 		fprintf(fp, "# bpf_prog_info %u: %s addr 0x%llx size %u\n",
 			info->id, name, prog_addrs[0], prog_lens[0]);
-		return;
+		goto out;
 	}
 
 	fprintf(fp, "# bpf_prog_info %u:\n", info->id);
@@ -586,4 +598,6 @@
 		fprintf(fp, "# \tsub_prog %u: %s addr 0x%llx size %u\n",
 			i, name, prog_addrs[i], prog_lens[i]);
 	}
+out:
+	btf__free(btf);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf-event.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf-event.h
@@ -34,9 +34,9 @@
 int machine__process_bpf(struct machine *machine, union perf_event *event,
 			 struct perf_sample *sample);
 int evlist__add_bpf_sb_event(struct evlist *evlist, struct perf_env *env);
-void bpf_event__print_bpf_prog_info(struct bpf_prog_info *info,
-				    struct perf_env *env,
-				    FILE *fp);
+void __bpf_event__print_bpf_prog_info(struct bpf_prog_info *info,
+				      struct perf_env *env,
+				      FILE *fp);
 #else
 static inline int machine__process_bpf(struct machine *machine __maybe_unused,
 				       union perf_event *event __maybe_unused,
@@ -51,9 +51,9 @@
 	return 0;
 }
 
-static inline void bpf_event__print_bpf_prog_info(struct bpf_prog_info *info __maybe_unused,
-						  struct perf_env *env __maybe_unused,
-						  FILE *fp __maybe_unused)
+static inline void __bpf_event__print_bpf_prog_info(struct bpf_prog_info *info __maybe_unused,
+						    struct perf_env *env __maybe_unused,
+						    FILE *fp __maybe_unused)
 {
 
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf-loader.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf-loader.c
@@ -1214,9 +1214,10 @@
 	pr_debug("ERROR: Invalid map config option '%s'\n", map_opt);
 	err = -BPF_LOADER_ERRNO__OBJCONF_MAP_OPT;
 out:
-	free(map_name);
 	if (!err)
 		*key_scan_pos += strlen(map_opt);
+
+	free(map_name);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf_counter.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf_counter.h
@@ -4,9 +4,12 @@
 
 #include <linux/list.h>
 #include <sys/resource.h>
+
+#ifdef HAVE_LIBBPF_SUPPORT
 #include <bpf/bpf.h>
 #include <bpf/btf.h>
 #include <bpf/libbpf.h>
+#endif
 
 struct evsel;
 struct target;
@@ -87,6 +90,8 @@
 	setrlimit(RLIMIT_MEMLOCK, &rinf);
 }
 
+#ifdef HAVE_BPF_SKEL
+
 static inline __u32 bpf_link_get_id(int fd)
 {
 	struct bpf_link_info link_info = { .id = 0, };
@@ -127,5 +132,6 @@
 
 	return bpf_prog_test_run_opts(prog_fd, &opts);
 }
+#endif /* HAVE_BPF_SKEL */
 
 #endif /* __PERF_BPF_COUNTER_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf_skel/bperf_cgroup.bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf_skel/bperf_cgroup.bpf.c
@@ -176,7 +176,7 @@
 }
 
 // This will be attached to cgroup-switches event for each cpu
-SEC("perf_events")
+SEC("perf_event")
 int BPF_PROG(on_cgrp_switch)
 {
 	return bperf_cgroup_count();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf_skel/bperf_follower.bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf_skel/bperf_follower.bpf.c
@@ -4,11 +4,21 @@
 #include <linux/perf_event.h>
 #include <bpf/bpf_helpers.h>
 #include <bpf/bpf_tracing.h>
-#include "bperf.h"
 #include "bperf_u.h"
 
-reading_map diff_readings SEC(".maps");
-reading_map accum_readings SEC(".maps");
+struct {
+	__uint(type, BPF_MAP_TYPE_PERCPU_ARRAY);
+	__uint(key_size, sizeof(__u32));
+	__uint(value_size, sizeof(struct bpf_perf_event_value));
+	__uint(max_entries, 1);
+} diff_readings SEC(".maps");
+
+struct {
+	__uint(type, BPF_MAP_TYPE_PERCPU_ARRAY);
+	__uint(key_size, sizeof(__u32));
+	__uint(value_size, sizeof(struct bpf_perf_event_value));
+	__uint(max_entries, 1);
+} accum_readings SEC(".maps");
 
 struct {
 	__uint(type, BPF_MAP_TYPE_HASH);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/bpf_skel/bperf_leader.bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/bpf_skel/bperf_leader.bpf.c
@@ -4,7 +4,6 @@
 #include <linux/perf_event.h>
 #include <bpf/bpf_helpers.h>
 #include <bpf/bpf_tracing.h>
-#include "bperf.h"
 
 struct {
 	__uint(type, BPF_MAP_TYPE_PERF_EVENT_ARRAY);
@@ -13,8 +12,19 @@
 	__uint(map_flags, BPF_F_PRESERVE_ELEMS);
 } events SEC(".maps");
 
-reading_map prev_readings SEC(".maps");
-reading_map diff_readings SEC(".maps");
+struct {
+	__uint(type, BPF_MAP_TYPE_PERCPU_ARRAY);
+	__uint(key_size, sizeof(__u32));
+	__uint(value_size, sizeof(struct bpf_perf_event_value));
+	__uint(max_entries, 1);
+} prev_readings SEC(".maps");
+
+struct {
+	__uint(type, BPF_MAP_TYPE_PERCPU_ARRAY);
+	__uint(key_size, sizeof(__u32));
+	__uint(value_size, sizeof(struct bpf_perf_event_value));
+	__uint(max_entries, 1);
+} diff_readings SEC(".maps");
 
 SEC("raw_tp/sched_switch")
 int BPF_PROG(on_switch)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/branch.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/branch.c
@@ -49,7 +49,9 @@
 		"SYSCALL",
 		"SYSRET",
 		"COND_CALL",
-		"COND_RET"
+		"COND_RET",
+		"ERET",
+		"IRQ"
 	};
 
 	if (type >= 0 && type < PERF_BR_MAX)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/build-id.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/build-id.c
@@ -872,6 +872,30 @@
 	return err;
 }
 
+static int filename__read_build_id_ns(const char *filename,
+				      struct build_id *bid,
+				      struct nsinfo *nsi)
+{
+	struct nscookie nsc;
+	int ret;
+
+	nsinfo__mountns_enter(nsi, &nsc);
+	ret = filename__read_build_id(filename, bid);
+	nsinfo__mountns_exit(&nsc);
+
+	return ret;
+}
+
+static bool dso__build_id_mismatch(struct dso *dso, const char *name)
+{
+	struct build_id bid;
+
+	if (filename__read_build_id_ns(name, &bid, dso->nsinfo) < 0)
+		return false;
+
+	return !dso__build_id_equal(dso, &bid);
+}
+
 static int dso__cache_build_id(struct dso *dso, struct machine *machine,
 			       void *priv __maybe_unused)
 {
@@ -886,6 +910,10 @@
 		is_kallsyms = true;
 		name = machine->mmap_name;
 	}
+
+	if (!is_kallsyms && dso__build_id_mismatch(dso, name))
+		return 0;
+
 	return build_id_cache__add_b(&dso->bid, name, dso->nsinfo,
 				     is_kallsyms, is_vdso);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/cgroup.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/cgroup.c
@@ -224,6 +224,19 @@
 	return 0;
 }
 
+static int check_and_add_cgroup_name(const char *fpath)
+{
+	struct cgroup_name *cn;
+
+	list_for_each_entry(cn, &cgroup_list, list) {
+		if (!strcmp(cn->name, fpath))
+			return 0;
+	}
+
+	/* pretend if it's added by ftw() */
+	return add_cgroup_name(fpath, NULL, FTW_D, NULL);
+}
+
 static void release_cgroup_list(void)
 {
 	struct cgroup_name *cn;
@@ -242,7 +255,7 @@
 	struct cgroup_name *cn;
 	char *s;
 
-	/* use given name as is - for testing purpose */
+	/* use given name as is when no regex is given */
 	for (;;) {
 		p = strchr(str, ',');
 		e = p ? p : eos;
@@ -253,13 +266,13 @@
 			s = strndup(str, e - str);
 			if (!s)
 				return -1;
-			/* pretend if it's added by ftw() */
-			ret = add_cgroup_name(s, NULL, FTW_D, NULL);
+
+			ret = check_and_add_cgroup_name(s);
 			free(s);
-			if (ret)
+			if (ret < 0)
 				return -1;
 		} else {
-			if (add_cgroup_name("", NULL, FTW_D, NULL) < 0)
+			if (check_and_add_cgroup_name("/") < 0)
 				return -1;
 		}
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/cs-etm.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/cs-etm.c
@@ -2126,12 +2126,6 @@
 
 		/* Ignore return value */
 		cs_etm__process_traceid_queue(etmq, tidq);
-
-		/*
-		 * Generate an instruction sample with the remaining
-		 * branchstack entries.
-		 */
-		cs_etm__flush(etmq, tidq);
 	}
 }
 
@@ -2228,7 +2222,7 @@
 
 	while (1) {
 		if (!etm->heap.heap_cnt)
-			goto out;
+			break;
 
 		/* Take the entry at the top of the min heap */
 		cs_queue_nr = etm->heap.heap_array[0].queue_nr;
@@ -2311,6 +2305,23 @@
 		ret = auxtrace_heap__add(&etm->heap, cs_queue_nr, cs_timestamp);
 	}
 
+	for (i = 0; i < etm->queues.nr_queues; i++) {
+		struct int_node *inode;
+
+		etmq = etm->queues.queue_array[i].priv;
+		if (!etmq)
+			continue;
+
+		intlist__for_each_entry(inode, etmq->traceid_queues_list) {
+			int idx = (int)(intptr_t)inode->priv;
+
+			/* Flush any remaining branch stack entries */
+			tidq = etmq->traceid_queues[idx];
+			ret = cs_etm__end_block(etmq, tidq);
+			if (ret)
+				return ret;
+		}
+	}
 out:
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/data.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/data.c
@@ -44,10 +44,6 @@
 	if (!files)
 		return -ENOMEM;
 
-	data->dir.version = PERF_DIR_VERSION;
-	data->dir.files   = files;
-	data->dir.nr      = nr;
-
 	for (i = 0; i < nr; i++) {
 		struct perf_data_file *file = &files[i];
 
@@ -62,6 +58,9 @@
 		file->fd = ret;
 	}
 
+	data->dir.version = PERF_DIR_VERSION;
+	data->dir.files   = files;
+	data->dir.nr      = nr;
 	return 0;
 
 out_err:
@@ -128,6 +127,7 @@
 		file->size = st.st_size;
 	}
 
+	closedir(dir);
 	if (!files)
 		return -EINVAL;
 
@@ -136,6 +136,7 @@
 	return 0;
 
 out_err:
+	closedir(dir);
 	close_dir(files, nr);
 	return ret;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/data.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/data.h
@@ -4,6 +4,7 @@
 
 #include <stdio.h>
 #include <stdbool.h>
+#include <linux/types.h>
 
 enum perf_data_mode {
 	PERF_DATA_MODE_WRITE,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/debug.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/debug.c
@@ -179,7 +179,7 @@
 		break;
 	case BINARY_PRINT_CHAR_DATA:
 		printed += color_fprintf(fp, color, "%c",
-			      isprint(ch) ? ch : '.');
+			      isprint(ch) && isascii(ch) ? ch : '.');
 		break;
 	case BINARY_PRINT_CHAR_PAD:
 		printed += color_fprintf(fp, color, " ");
@@ -241,6 +241,10 @@
 		opt++;
 	}
 
+	/* For debug variables that are used as bool types, set to 0. */
+	redirect_to_stderr = 0;
+	debug_peo_args = 0;
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/dsos.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/dsos.c
@@ -20,8 +20,19 @@
 	if (a->ino > b->ino) return -1;
 	if (a->ino < b->ino) return 1;
 
-	if (a->ino_generation > b->ino_generation) return -1;
-	if (a->ino_generation < b->ino_generation) return 1;
+	/*
+	 * Synthesized MMAP events have zero ino_generation, avoid comparing
+	 * them with MMAP events with actual ino_generation.
+	 *
+	 * I found it harmful because the mismatch resulted in a new
+	 * dso that did not have a build ID whereas the original dso did have a
+	 * build ID. The build ID was essential because the object was not found
+	 * otherwise. - Adrian
+	 */
+	if (a->ino_generation && b->ino_generation) {
+		if (a->ino_generation > b->ino_generation) return -1;
+		if (a->ino_generation < b->ino_generation) return 1;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/dwarf-aux.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/dwarf-aux.c
@@ -308,26 +308,13 @@
 {
 	Dwarf_Attribute attr;
 
-	if (dwarf_attr(tp_die, attr_name, &attr) == NULL ||
+	if (dwarf_attr_integrate(tp_die, attr_name, &attr) == NULL ||
 	    dwarf_formudata(&attr, result) != 0)
 		return -ENOENT;
 
 	return 0;
 }
 
-/* Get attribute and translate it as a sdata */
-static int die_get_attr_sdata(Dwarf_Die *tp_die, unsigned int attr_name,
-			      Dwarf_Sword *result)
-{
-	Dwarf_Attribute attr;
-
-	if (dwarf_attr(tp_die, attr_name, &attr) == NULL ||
-	    dwarf_formsdata(&attr, result) != 0)
-		return -ENOENT;
-
-	return 0;
-}
-
 /**
  * die_is_signed_type - Check whether a type DIE is signed or not
  * @tp_die: a DIE of a type
@@ -467,9 +454,9 @@
 /* Get the call file index number in CU DIE */
 static int die_get_call_fileno(Dwarf_Die *in_die)
 {
-	Dwarf_Sword idx;
+	Dwarf_Word idx;
 
-	if (die_get_attr_sdata(in_die, DW_AT_call_file, &idx) == 0)
+	if (die_get_attr_udata(in_die, DW_AT_call_file, &idx) == 0)
 		return (int)idx;
 	else
 		return -ENOENT;
@@ -478,9 +465,9 @@
 /* Get the declared file index number in CU DIE */
 static int die_get_decl_fileno(Dwarf_Die *pdie)
 {
-	Dwarf_Sword idx;
+	Dwarf_Word idx;
 
-	if (die_get_attr_sdata(pdie, DW_AT_decl_file, &idx) == 0)
+	if (die_get_attr_udata(pdie, DW_AT_decl_file, &idx) == 0)
 		return (int)idx;
 	else
 		return -ENOENT;
@@ -1094,7 +1081,7 @@
 	ret = die_get_typename(vr_die, buf);
 	if (ret < 0) {
 		pr_debug("Failed to get type, make it unknown.\n");
-		ret = strbuf_add(buf, " (unknown_type)", 14);
+		ret = strbuf_add(buf, "(unknown_type)", 14);
 	}
 
 	return ret < 0 ? ret : strbuf_addf(buf, "\t%s", dwarf_diename(vr_die));
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/env.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/env.c
@@ -18,15 +18,25 @@
 #include "bpf-event.h"
 #include <bpf/libbpf.h>
 
-void perf_env__insert_bpf_prog_info(struct perf_env *env,
+bool perf_env__insert_bpf_prog_info(struct perf_env *env,
 				    struct bpf_prog_info_node *info_node)
 {
+	bool ret;
+
+	down_write(&env->bpf_progs.lock);
+	ret = __perf_env__insert_bpf_prog_info(env, info_node);
+	up_write(&env->bpf_progs.lock);
+
+	return ret;
+}
+
+bool __perf_env__insert_bpf_prog_info(struct perf_env *env, struct bpf_prog_info_node *info_node)
+{
 	__u32 prog_id = info_node->info_linear->info.id;
 	struct bpf_prog_info_node *node;
 	struct rb_node *parent = NULL;
 	struct rb_node **p;
 
-	down_write(&env->bpf_progs.lock);
 	p = &env->bpf_progs.infos.rb_node;
 
 	while (*p != NULL) {
@@ -38,15 +48,14 @@
 			p = &(*p)->rb_right;
 		} else {
 			pr_debug("duplicated bpf prog info %u\n", prog_id);
-			goto out;
+			return false;
 		}
 	}
 
 	rb_link_node(&info_node->rb_node, parent, p);
 	rb_insert_color(&info_node->rb_node, &env->bpf_progs.infos);
 	env->bpf_progs.infos_cnt++;
-out:
-	up_write(&env->bpf_progs.lock);
+	return true;
 }
 
 struct bpf_prog_info_node *perf_env__find_bpf_prog_info(struct perf_env *env,
@@ -74,14 +83,23 @@
 	return node;
 }
 
-void perf_env__insert_btf(struct perf_env *env, struct btf_node *btf_node)
+bool perf_env__insert_btf(struct perf_env *env, struct btf_node *btf_node)
+{
+	bool ret;
+
+	down_write(&env->bpf_progs.lock);
+	ret = __perf_env__insert_btf(env, btf_node);
+	up_write(&env->bpf_progs.lock);
+	return ret;
+}
+
+bool __perf_env__insert_btf(struct perf_env *env, struct btf_node *btf_node)
 {
 	struct rb_node *parent = NULL;
 	__u32 btf_id = btf_node->id;
 	struct btf_node *node;
 	struct rb_node **p;
 
-	down_write(&env->bpf_progs.lock);
 	p = &env->bpf_progs.btfs.rb_node;
 
 	while (*p != NULL) {
@@ -93,23 +111,31 @@
 			p = &(*p)->rb_right;
 		} else {
 			pr_debug("duplicated btf %u\n", btf_id);
-			goto out;
+			return false;
 		}
 	}
 
 	rb_link_node(&btf_node->rb_node, parent, p);
 	rb_insert_color(&btf_node->rb_node, &env->bpf_progs.btfs);
 	env->bpf_progs.btfs_cnt++;
-out:
-	up_write(&env->bpf_progs.lock);
+	return true;
 }
 
 struct btf_node *perf_env__find_btf(struct perf_env *env, __u32 btf_id)
 {
+	struct btf_node *res;
+
+	down_read(&env->bpf_progs.lock);
+	res = __perf_env__find_btf(env, btf_id);
+	up_read(&env->bpf_progs.lock);
+	return res;
+}
+
+struct btf_node *__perf_env__find_btf(struct perf_env *env, __u32 btf_id)
+{
 	struct btf_node *node = NULL;
 	struct rb_node *n;
 
-	down_read(&env->bpf_progs.lock);
 	n = env->bpf_progs.btfs.rb_node;
 
 	while (n) {
@@ -119,13 +145,9 @@
 		else if (btf_id > node->id)
 			n = n->rb_right;
 		else
-			goto out;
+			return node;
 	}
-	node = NULL;
-
-out:
-	up_read(&env->bpf_progs.lock);
-	return node;
+	return NULL;
 }
 
 /* purge data in bpf_progs.infos tree */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/env.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/env.h
@@ -163,12 +163,16 @@
 int perf_env__nr_cpus_avail(struct perf_env *env);
 
 void perf_env__init(struct perf_env *env);
-void perf_env__insert_bpf_prog_info(struct perf_env *env,
+bool __perf_env__insert_bpf_prog_info(struct perf_env *env,
+				      struct bpf_prog_info_node *info_node);
+bool perf_env__insert_bpf_prog_info(struct perf_env *env,
 				    struct bpf_prog_info_node *info_node);
 struct bpf_prog_info_node *perf_env__find_bpf_prog_info(struct perf_env *env,
 							__u32 prog_id);
-void perf_env__insert_btf(struct perf_env *env, struct btf_node *btf_node);
+bool perf_env__insert_btf(struct perf_env *env, struct btf_node *btf_node);
+bool __perf_env__insert_btf(struct perf_env *env, struct btf_node *btf_node);
 struct btf_node *perf_env__find_btf(struct perf_env *env, __u32 btf_id);
+struct btf_node *__perf_env__find_btf(struct perf_env *env, __u32 btf_id);
 
 int perf_env__numa_node(struct perf_env *env, int cpu);
 #endif /* __PERF_ENV_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/evlist-hybrid.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/evlist-hybrid.c
@@ -153,8 +153,8 @@
 		perf_cpu_map__put(matched_cpus);
 		perf_cpu_map__put(unmatched_cpus);
 	}
-
-	ret = (unmatched_count == events_nr) ? -1 : 0;
+	if (events_nr)
+		ret = (unmatched_count == events_nr) ? -1 : 0;
 out:
 	perf_cpu_map__put(cpus);
 	return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/evlist.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/evlist.c
@@ -342,36 +342,65 @@
 		return perf_thread_map__nr(evlist->core.threads);
 }
 
-void evlist__cpu_iter_start(struct evlist *evlist)
+struct evlist_cpu_iterator evlist__cpu_begin(struct evlist *evlist, struct affinity *affinity)
 {
-	struct evsel *pos;
+	struct evlist_cpu_iterator itr = {
+		.container = evlist,
+		.evsel = evlist__first(evlist),
+		.cpu_map_idx = 0,
+		.evlist_cpu_map_idx = 0,
+		.evlist_cpu_map_nr = perf_cpu_map__nr(evlist->core.all_cpus),
+		.cpu = -1,
+		.affinity = affinity,
+	};
 
-	/*
-	 * Reset the per evsel cpu_iter. This is needed because
-	 * each evsel's cpumap may have a different index space,
-	 * and some operations need the index to modify
-	 * the FD xyarray (e.g. open, close)
-	 */
-	evlist__for_each_entry(evlist, pos)
-		pos->cpu_iter = 0;
+	if (itr.affinity) {
+		itr.cpu = perf_cpu_map__cpu(evlist->core.all_cpus, 0);
+		affinity__set(itr.affinity, itr.cpu);
+		itr.cpu_map_idx = perf_cpu_map__idx(itr.evsel->core.cpus, itr.cpu);
+		/*
+		 * If this CPU isn't in the evsel's cpu map then advance through
+		 * the list.
+		 */
+		if (itr.cpu_map_idx == -1)
+			evlist_cpu_iterator__next(&itr);
+	}
+	return itr;
 }
 
-bool evsel__cpu_iter_skip_no_inc(struct evsel *ev, int cpu)
+void evlist_cpu_iterator__next(struct evlist_cpu_iterator *evlist_cpu_itr)
 {
-	if (ev->cpu_iter >= ev->core.cpus->nr)
-		return true;
-	if (cpu >= 0 && ev->core.cpus->map[ev->cpu_iter] != cpu)
-		return true;
-	return false;
+	while (evlist_cpu_itr->evsel != evlist__last(evlist_cpu_itr->container)) {
+		evlist_cpu_itr->evsel = evsel__next(evlist_cpu_itr->evsel);
+		evlist_cpu_itr->cpu_map_idx =
+			perf_cpu_map__idx(evlist_cpu_itr->evsel->core.cpus,
+					  evlist_cpu_itr->cpu);
+		if (evlist_cpu_itr->cpu_map_idx != -1)
+			return;
+	}
+	evlist_cpu_itr->evlist_cpu_map_idx++;
+	if (evlist_cpu_itr->evlist_cpu_map_idx < evlist_cpu_itr->evlist_cpu_map_nr) {
+		evlist_cpu_itr->evsel = evlist__first(evlist_cpu_itr->container);
+		evlist_cpu_itr->cpu =
+			perf_cpu_map__cpu(evlist_cpu_itr->container->core.all_cpus,
+					  evlist_cpu_itr->evlist_cpu_map_idx);
+		if (evlist_cpu_itr->affinity)
+			affinity__set(evlist_cpu_itr->affinity, evlist_cpu_itr->cpu);
+		evlist_cpu_itr->cpu_map_idx =
+			perf_cpu_map__idx(evlist_cpu_itr->evsel->core.cpus,
+					  evlist_cpu_itr->cpu);
+		/*
+		 * If this CPU isn't in the evsel's cpu map then advance through
+		 * the list.
+		 */
+		if (evlist_cpu_itr->cpu_map_idx == -1)
+			evlist_cpu_iterator__next(evlist_cpu_itr);
+	}
 }
 
-bool evsel__cpu_iter_skip(struct evsel *ev, int cpu)
+bool evlist_cpu_iterator__end(const struct evlist_cpu_iterator *evlist_cpu_itr)
 {
-	if (!evsel__cpu_iter_skip_no_inc(ev, cpu)) {
-		ev->cpu_iter++;
-		return false;
-	}
-	return true;
+	return evlist_cpu_itr->evlist_cpu_map_idx >= evlist_cpu_itr->evlist_cpu_map_nr;
 }
 
 static int evsel__strcmp(struct evsel *pos, char *evsel_name)
@@ -400,31 +429,26 @@
 static void __evlist__disable(struct evlist *evlist, char *evsel_name)
 {
 	struct evsel *pos;
+	struct evlist_cpu_iterator evlist_cpu_itr;
 	struct affinity affinity;
-	int cpu, i, imm = 0;
 	bool has_imm = false;
 
 	if (affinity__setup(&affinity) < 0)
 		return;
 
 	/* Disable 'immediate' events last */
-	for (imm = 0; imm <= 1; imm++) {
-		evlist__for_each_cpu(evlist, i, cpu) {
-			affinity__set(&affinity, cpu);
-
-			evlist__for_each_entry(evlist, pos) {
-				if (evsel__strcmp(pos, evsel_name))
-					continue;
-				if (evsel__cpu_iter_skip(pos, cpu))
-					continue;
-				if (pos->disabled || !evsel__is_group_leader(pos) || !pos->core.fd)
-					continue;
-				if (pos->immediate)
-					has_imm = true;
-				if (pos->immediate != imm)
-					continue;
-				evsel__disable_cpu(pos, pos->cpu_iter - 1);
-			}
+	for (int imm = 0; imm <= 1; imm++) {
+		evlist__for_each_cpu(evlist_cpu_itr, evlist, &affinity) {
+			pos = evlist_cpu_itr.evsel;
+			if (evsel__strcmp(pos, evsel_name))
+				continue;
+			if (pos->disabled || !evsel__is_group_leader(pos) || !pos->core.fd)
+				continue;
+			if (pos->immediate)
+				has_imm = true;
+			if (pos->immediate != imm)
+				continue;
+			evsel__disable_cpu(pos, evlist_cpu_itr.cpu_map_idx);
 		}
 		if (!has_imm)
 			break;
@@ -462,24 +486,19 @@
 static void __evlist__enable(struct evlist *evlist, char *evsel_name)
 {
 	struct evsel *pos;
+	struct evlist_cpu_iterator evlist_cpu_itr;
 	struct affinity affinity;
-	int cpu, i;
 
 	if (affinity__setup(&affinity) < 0)
 		return;
 
-	evlist__for_each_cpu(evlist, i, cpu) {
-		affinity__set(&affinity, cpu);
-
-		evlist__for_each_entry(evlist, pos) {
-			if (evsel__strcmp(pos, evsel_name))
-				continue;
-			if (evsel__cpu_iter_skip(pos, cpu))
-				continue;
-			if (!evsel__is_group_leader(pos) || !pos->core.fd)
-				continue;
-			evsel__enable_cpu(pos, pos->cpu_iter - 1);
-		}
+	evlist__for_each_cpu(evlist_cpu_itr, evlist, &affinity) {
+		pos = evlist_cpu_itr.evsel;
+		if (evsel__strcmp(pos, evsel_name))
+			continue;
+		if (!evsel__is_group_leader(pos) || !pos->core.fd)
+			continue;
+		evsel__enable_cpu(pos, evlist_cpu_itr.cpu_map_idx);
 	}
 	affinity__cleanup(&affinity);
 	evlist__for_each_entry(evlist, pos) {
@@ -1264,8 +1283,8 @@
 void evlist__close(struct evlist *evlist)
 {
 	struct evsel *evsel;
+	struct evlist_cpu_iterator evlist_cpu_itr;
 	struct affinity affinity;
-	int cpu, i;
 
 	/*
 	 * With perf record core.cpus is usually NULL.
@@ -1279,15 +1298,12 @@
 
 	if (affinity__setup(&affinity) < 0)
 		return;
-	evlist__for_each_cpu(evlist, i, cpu) {
-		affinity__set(&affinity, cpu);
 
-		evlist__for_each_entry_reverse(evlist, evsel) {
-			if (evsel__cpu_iter_skip(evsel, cpu))
-			    continue;
-			perf_evsel__close_cpu(&evsel->core, evsel->cpu_iter - 1);
-		}
+	evlist__for_each_cpu(evlist_cpu_itr, evlist, &affinity) {
+		perf_evsel__close_cpu(&evlist_cpu_itr.evsel->core,
+				      evlist_cpu_itr.cpu_map_idx);
 	}
+
 	affinity__cleanup(&affinity);
 	evlist__for_each_entry_reverse(evlist, evsel) {
 		perf_evsel__free_fd(&evsel->core);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/evlist.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/evlist.h
@@ -325,17 +325,53 @@
 #define evlist__for_each_entry_safe(evlist, tmp, evsel) \
 	__evlist__for_each_entry_safe(&(evlist)->core.entries, tmp, evsel)
 
-#define evlist__for_each_cpu(evlist, index, cpu)	\
-	evlist__cpu_iter_start(evlist);			\
-	perf_cpu_map__for_each_cpu (cpu, index, (evlist)->core.all_cpus)
+/** Iterator state for evlist__for_each_cpu */
+struct evlist_cpu_iterator {
+	/** The list being iterated through. */
+	struct evlist *container;
+	/** The current evsel of the iterator. */
+	struct evsel *evsel;
+	/** The CPU map index corresponding to the evsel->core.cpus for the current CPU. */
+	int cpu_map_idx;
+	/**
+	 * The CPU map index corresponding to evlist->core.all_cpus for the
+	 * current CPU.  Distinct from cpu_map_idx as the evsel's cpu map may
+	 * contain fewer entries.
+	 */
+	int evlist_cpu_map_idx;
+	/** The number of CPU map entries in evlist->core.all_cpus. */
+	int evlist_cpu_map_nr;
+	/** The current CPU of the iterator. */
+	int cpu;
+	/** If present, used to set the affinity when switching between CPUs. */
+	struct affinity *affinity;
+};
+
+/**
+ * evlist__for_each_cpu - without affinity, iterate over the evlist. With
+ *                        affinity, iterate over all CPUs and then the evlist
+ *                        for each evsel on that CPU. When switching between
+ *                        CPUs the affinity is set to the CPU to avoid IPIs
+ *                        during syscalls.
+ * @evlist_cpu_itr: the iterator instance.
+ * @evlist: evlist instance to iterate.
+ * @affinity: NULL or used to set the affinity to the current CPU.
+ */
+#define evlist__for_each_cpu(evlist_cpu_itr, evlist, affinity)		\
+	for ((evlist_cpu_itr) = evlist__cpu_begin(evlist, affinity);	\
+	     !evlist_cpu_iterator__end(&evlist_cpu_itr);		\
+	     evlist_cpu_iterator__next(&evlist_cpu_itr))
+
+/** Returns an iterator set to the first CPU/evsel of evlist. */
+struct evlist_cpu_iterator evlist__cpu_begin(struct evlist *evlist, struct affinity *affinity);
+/** Move to next element in iterator, updating CPU, evsel and the affinity. */
+void evlist_cpu_iterator__next(struct evlist_cpu_iterator *evlist_cpu_itr);
+/** Returns true when iterator is at the end of the CPUs and evlist. */
+bool evlist_cpu_iterator__end(const struct evlist_cpu_iterator *evlist_cpu_itr);
 
 struct evsel *evlist__get_tracking_event(struct evlist *evlist);
 void evlist__set_tracking_event(struct evlist *evlist, struct evsel *tracking_evsel);
 
-void evlist__cpu_iter_start(struct evlist *evlist);
-bool evsel__cpu_iter_skip(struct evsel *ev, int cpu);
-bool evsel__cpu_iter_skip_no_inc(struct evsel *ev, int cpu);
-
 struct evsel *evlist__find_evsel_by_str(struct evlist *evlist, const char *str);
 
 struct evsel *evlist__event2evsel(struct evlist *evlist, union perf_event *event);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/evsel.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/evsel.c
@@ -1047,6 +1047,17 @@
 	evsel__set_sample_bit(evsel, WEIGHT);
 }
 
+static void evsel__set_default_freq_period(struct record_opts *opts,
+					   struct perf_event_attr *attr)
+{
+	if (opts->freq) {
+		attr->freq = 1;
+		attr->sample_freq = opts->freq;
+	} else {
+		attr->sample_period = opts->default_interval;
+	}
+}
+
 /*
  * The enable_on_exec/disabled value strategy:
  *
@@ -1113,14 +1124,12 @@
 	 * We default some events to have a default interval. But keep
 	 * it a weak assumption overridable by the user.
 	 */
-	if (!attr->sample_period) {
-		if (opts->freq) {
-			attr->freq		= 1;
-			attr->sample_freq	= opts->freq;
-		} else {
-			attr->sample_period = opts->default_interval;
-		}
-	}
+	if ((evsel->is_libpfm_event && !attr->sample_period) ||
+	    (!evsel->is_libpfm_event && (!attr->sample_period ||
+					 opts->user_freq != UINT_MAX ||
+					 opts->user_interval != ULLONG_MAX)))
+		evsel__set_default_freq_period(opts, attr);
+
 	/*
 	 * If attr->freq was set (here or earlier), ask for period
 	 * to be sampled.
@@ -2243,7 +2252,6 @@
 	data->period = evsel->core.attr.sample_period;
 	data->cpumode = event->header.misc & PERF_RECORD_MISC_CPUMODE_MASK;
 	data->misc    = event->header.misc;
-	data->id = -1ULL;
 	data->data_src = PERF_MEM_DATA_SRC_NONE;
 
 	if (event->header.type != PERF_RECORD_SAMPLE) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/evsel.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/evsel.h
@@ -119,7 +119,6 @@
 	bool			errored;
 	struct hashmap		*per_pkg_mask;
 	int			err;
-	int			cpu_iter;
 	struct {
 		evsel__sb_cb_t	*cb;
 		void		*data;
@@ -249,6 +248,11 @@
 	return evsel->bpf_counter_ops != NULL;
 }
 
+static inline bool evsel__is_bperf(struct evsel *evsel)
+{
+	return evsel->bpf_counter_ops != NULL && list_empty(&evsel->bpf_counter_list);
+}
+
 #define EVSEL__MAX_ALIASES 8
 
 extern const char *evsel__hw_cache[PERF_COUNT_HW_CACHE_MAX][EVSEL__MAX_ALIASES];
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/genelf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/genelf.c
@@ -30,7 +30,11 @@
 
 #define BUILD_ID_URANDOM /* different uuid for each run */
 
-#ifdef HAVE_LIBCRYPTO
+// FIXME, remove this and fix the deprecation warnings before its removed and
+// We'll break for good here...
+#pragma GCC diagnostic ignored "-Wdeprecated-declarations"
+
+#ifdef HAVE_LIBCRYPTO_SUPPORT
 
 #define BUILD_ID_MD5
 #undef BUILD_ID_SHA	/* does not seem to work well when linked with Java */
@@ -247,6 +251,7 @@
 	Elf_Data *d;
 	Elf_Scn *scn;
 	Elf_Ehdr *ehdr;
+	Elf_Phdr *phdr;
 	Elf_Shdr *shdr;
 	uint64_t eh_frame_base_offset;
 	char *strsym = NULL;
@@ -282,6 +287,19 @@
 	ehdr->e_shstrndx= unwinding ? 4 : 2; /* shdr index for section name */
 
 	/*
+	 * setup program header
+	 */
+	phdr = elf_newphdr(e, 1);
+	phdr[0].p_type = PT_LOAD;
+	phdr[0].p_offset = GEN_ELF_TEXT_OFFSET;
+	phdr[0].p_vaddr = GEN_ELF_TEXT_OFFSET;
+	phdr[0].p_paddr = GEN_ELF_TEXT_OFFSET;
+	phdr[0].p_filesz = csize;
+	phdr[0].p_memsz = csize;
+	phdr[0].p_flags = PF_X | PF_R;
+	phdr[0].p_align = 8;
+
+	/*
 	 * setup text section
 	 */
 	scn = elf_newscn(e);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/genelf.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/genelf.h
@@ -2,6 +2,8 @@
 #ifndef __GENELF_H__
 #define __GENELF_H__
 
+#include <linux/kernel.h>
+
 /* genelf.c */
 int jit_write_elf(int fd, uint64_t code_addr, const char *sym,
 		  const void *code, int csize, void *debug, int nr_debug_entries,
@@ -50,8 +52,10 @@
 
 #if GEN_ELF_CLASS == ELFCLASS64
 #define elf_newehdr	elf64_newehdr
+#define elf_newphdr	elf64_newphdr
 #define elf_getshdr	elf64_getshdr
 #define Elf_Ehdr	Elf64_Ehdr
+#define Elf_Phdr	Elf64_Phdr
 #define Elf_Shdr	Elf64_Shdr
 #define Elf_Sym		Elf64_Sym
 #define ELF_ST_TYPE(a)	ELF64_ST_TYPE(a)
@@ -59,8 +63,10 @@
 #define ELF_ST_VIS(a)	ELF64_ST_VISIBILITY(a)
 #else
 #define elf_newehdr	elf32_newehdr
+#define elf_newphdr	elf32_newphdr
 #define elf_getshdr	elf32_getshdr
 #define Elf_Ehdr	Elf32_Ehdr
+#define Elf_Phdr	Elf32_Phdr
 #define Elf_Shdr	Elf32_Shdr
 #define Elf_Sym		Elf32_Sym
 #define ELF_ST_TYPE(a)	ELF32_ST_TYPE(a)
@@ -69,6 +75,6 @@
 #endif
 
 /* The .text section is directly after the ELF header */
-#define GEN_ELF_TEXT_OFFSET sizeof(Elf_Ehdr)
+#define GEN_ELF_TEXT_OFFSET round_up(sizeof(Elf_Ehdr) + sizeof(Elf_Phdr), 16)
 
 #endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/header.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/header.c
@@ -1735,8 +1735,8 @@
 		node = rb_entry(next, struct bpf_prog_info_node, rb_node);
 		next = rb_next(&node->rb_node);
 
-		bpf_event__print_bpf_prog_info(&node->info_linear->info,
-					       env, fp);
+		__bpf_event__print_bpf_prog_info(&node->info_linear->info,
+						 env, fp);
 	}
 
 	up_read(&env->bpf_progs.lock);
@@ -3073,7 +3073,10 @@
 		/* after reading from file, translate offset to address */
 		bpf_program__bpil_offs_to_addr(info_linear);
 		info_node->info_linear = info_linear;
-		perf_env__insert_bpf_prog_info(env, info_node);
+		if (!__perf_env__insert_bpf_prog_info(env, info_node)) {
+			free(info_linear);
+			free(info_node);
+		}
 	}
 
 	up_write(&env->bpf_progs.lock);
@@ -3120,7 +3123,8 @@
 		if (__do_read(ff, node->data, data_size))
 			goto out;
 
-		perf_env__insert_btf(env, node);
+		if (!__perf_env__insert_btf(env, node))
+			free(node);
 		node = NULL;
 	}
 
@@ -4200,7 +4204,8 @@
 			     union perf_event *event,
 			     struct evlist **pevlist)
 {
-	u32 i, ids, n_ids;
+	u32 i, n_ids;
+	u64 *ids;
 	struct evsel *evsel;
 	struct evlist *evlist = *pevlist;
 
@@ -4216,9 +4221,8 @@
 
 	evlist__add(evlist, evsel);
 
-	ids = event->header.size;
-	ids -= (void *)&event->attr.id - (void *)event;
-	n_ids = ids / sizeof(u64);
+	n_ids = event->header.size - sizeof(event->header) - event->attr.attr.size;
+	n_ids = n_ids / sizeof(u64);
 	/*
 	 * We don't have the cpu and thread maps on the header, so
 	 * for allocating the perf_sample_id table we fake 1 cpu and
@@ -4227,8 +4231,9 @@
 	if (perf_evsel__alloc_id(&evsel->core, 1, n_ids))
 		return -ENOMEM;
 
+	ids = (void *)&event->attr.attr + event->attr.attr.size;
 	for (i = 0; i < n_ids; i++) {
-		perf_evlist__id_add(&evlist->core, &evsel->core, 0, i, event->attr.id[i]);
+		perf_evlist__id_add(&evlist->core, &evsel->core, 0, i, ids[i]);
 	}
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/hist.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/hist.c
@@ -289,15 +289,10 @@
 	return htime;
 }
 
-static void he_stat__add_period(struct he_stat *he_stat, u64 period,
-				u64 weight, u64 ins_lat, u64 p_stage_cyc)
+static void he_stat__add_period(struct he_stat *he_stat, u64 period)
 {
-
 	he_stat->period		+= period;
-	he_stat->weight		+= weight;
 	he_stat->nr_events	+= 1;
-	he_stat->ins_lat	+= ins_lat;
-	he_stat->p_stage_cyc	+= p_stage_cyc;
 }
 
 static void he_stat__add_stat(struct he_stat *dest, struct he_stat *src)
@@ -308,9 +303,6 @@
 	dest->period_guest_sys	+= src->period_guest_sys;
 	dest->period_guest_us	+= src->period_guest_us;
 	dest->nr_events		+= src->nr_events;
-	dest->weight		+= src->weight;
-	dest->ins_lat		+= src->ins_lat;
-	dest->p_stage_cyc		+= src->p_stage_cyc;
 }
 
 static void he_stat__decay(struct he_stat *he_stat)
@@ -598,9 +590,6 @@
 	struct hist_entry *he;
 	int64_t cmp;
 	u64 period = entry->stat.period;
-	u64 weight = entry->stat.weight;
-	u64 ins_lat = entry->stat.ins_lat;
-	u64 p_stage_cyc = entry->stat.p_stage_cyc;
 	bool leftmost = true;
 
 	p = &hists->entries_in->rb_root.rb_node;
@@ -619,11 +608,11 @@
 
 		if (!cmp) {
 			if (sample_self) {
-				he_stat__add_period(&he->stat, period, weight, ins_lat, p_stage_cyc);
+				he_stat__add_period(&he->stat, period);
 				hist_entry__add_callchain_period(he, period);
 			}
 			if (symbol_conf.cumulate_callchain)
-				he_stat__add_period(he->stat_acc, period, weight, ins_lat, p_stage_cyc);
+				he_stat__add_period(he->stat_acc, period);
 
 			/*
 			 * This mem info was allocated from sample__resolve_mem
@@ -639,7 +628,12 @@
 			 * mis-adjust symbol addresses when computing
 			 * the history counter to increment.
 			 */
-			if (he->ms.map != entry->ms.map) {
+			if (hists__has(hists, sym) && he->ms.map != entry->ms.map) {
+				if (he->ms.sym) {
+					u64 addr = he->ms.sym->start;
+					he->ms.sym = map__find_symbol(entry->ms.map, addr);
+				}
+
 				map__put(he->ms.map);
 				he->ms.map = map__get(entry->ms.map);
 			}
@@ -733,9 +727,6 @@
 		.stat = {
 			.nr_events = 1,
 			.period	= sample->period,
-			.weight = sample->weight,
-			.ins_lat = sample->ins_lat,
-			.p_stage_cyc = sample->p_stage_cyc,
 		},
 		.parent = sym_parent,
 		.filtered = symbol__parent_filter(sym_parent) | al->filtered,
@@ -748,6 +739,9 @@
 		.raw_size = sample->raw_size,
 		.ops = ops,
 		.time = hist_time(sample->time),
+		.weight = sample->weight,
+		.ins_lat = sample->ins_lat,
+		.p_stage_cyc = sample->p_stage_cyc,
 	}, *he = hists__findnew_entry(hists, &entry, al, sample_self);
 
 	if (!hists->has_callchains && he && he->callchain_size != 0)
@@ -2646,8 +2640,6 @@
 
 	/* If we have branch cycles always annotate them. */
 	if (bs && bs->nr && entries[0].flags.cycles) {
-		int i;
-
 		bi = sample__resolve_bstack(sample, al);
 		if (bi) {
 			struct addr_map_symbol *prev = NULL;
@@ -2662,7 +2654,7 @@
 			 * Note that perf stores branches reversed from
 			 * program order!
 			 */
-			for (i = bs->nr - 1; i >= 0; i--) {
+			for (int i = bs->nr - 1; i >= 0; i--) {
 				addr_map_symbol__account_cycles(&bi[i].from,
 					nonany_branch_mode ? NULL : prev,
 					bi[i].flags.cycles);
@@ -2671,6 +2663,12 @@
 				if (total_cycles)
 					*total_cycles += bi[i].flags.cycles;
 			}
+			for (unsigned int i = 0; i < bs->nr; i++) {
+				map__put(bi[i].to.ms.map);
+				maps__put(bi[i].to.ms.maps);
+				map__put(bi[i].from.ms.map);
+				maps__put(bi[i].from.ms.maps);
+			}
 			free(bi);
 		}
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/hist.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/hist.h
@@ -369,7 +369,6 @@
 };
 
 void perf_hpp__init(void);
-void perf_hpp__column_unregister(struct perf_hpp_fmt *format);
 void perf_hpp__cancel_cumulate(void);
 void perf_hpp__setup_output_field(struct perf_hpp_list *list);
 void perf_hpp__reset_output_field(struct perf_hpp_list *list);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/Build
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/Build
@@ -18,3 +18,5 @@
 ifeq ($(CC_NO_CLANG), 1)
   CFLAGS_intel-pt-insn-decoder.o += -Wno-override-init
 endif
+
+CFLAGS_intel-pt-insn-decoder.o += -Wno-packed
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/intel-pt-decoder.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/intel-pt-decoder.c
@@ -137,6 +137,7 @@
 	bool in_psb;
 	bool hop;
 	bool leap;
+	bool emulated_ptwrite;
 	bool vm_time_correlation;
 	bool vm_tm_corr_dry_run;
 	bool vm_tm_corr_reliable;
@@ -473,6 +474,8 @@
 		return INTEL_PT_ERR_LOST;
 	case -ELOOP:
 		return INTEL_PT_ERR_NELOOP;
+	case -ECONNRESET:
+		return INTEL_PT_ERR_EPTW;
 	default:
 		return INTEL_PT_ERR_UNK;
 	}
@@ -489,6 +492,7 @@
 	[INTEL_PT_ERR_LOST]   = "Lost trace data",
 	[INTEL_PT_ERR_UNK]    = "Unknown error!",
 	[INTEL_PT_ERR_NELOOP] = "Never-ending loop (refer perf config intel-pt.max-loops)",
+	[INTEL_PT_ERR_EPTW]   = "Broken emulated ptwrite",
 };
 
 int intel_pt__strerror(int code, char *buf, size_t buflen)
@@ -819,6 +823,9 @@
 	case INTEL_PT_BIP:
 	case INTEL_PT_BEP:
 	case INTEL_PT_BEP_IP:
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+	case INTEL_PT_EVD:
 		return 0;
 
 	case INTEL_PT_MTC:
@@ -1204,61 +1211,69 @@
 
 static bool intel_pt_fup_event(struct intel_pt_decoder *decoder)
 {
+	enum intel_pt_sample_type type = decoder->state.type;
 	bool ret = false;
 
+	decoder->state.type &= ~INTEL_PT_BRANCH;
+
 	if (decoder->set_fup_tx_flags) {
 		decoder->set_fup_tx_flags = false;
 		decoder->tx_flags = decoder->fup_tx_flags;
-		decoder->state.type = INTEL_PT_TRANSACTION;
+		decoder->state.type |= INTEL_PT_TRANSACTION;
 		if (decoder->fup_tx_flags & INTEL_PT_ABORT_TX)
 			decoder->state.type |= INTEL_PT_BRANCH;
-		decoder->state.from_ip = decoder->ip;
-		decoder->state.to_ip = 0;
 		decoder->state.flags = decoder->fup_tx_flags;
-		return true;
+		ret = true;
 	}
 	if (decoder->set_fup_ptw) {
 		decoder->set_fup_ptw = false;
-		decoder->state.type = INTEL_PT_PTW;
+		decoder->state.type |= INTEL_PT_PTW;
 		decoder->state.flags |= INTEL_PT_FUP_IP;
-		decoder->state.from_ip = decoder->ip;
-		decoder->state.to_ip = 0;
 		decoder->state.ptw_payload = decoder->fup_ptw_payload;
-		return true;
+		ret = true;
 	}
 	if (decoder->set_fup_mwait) {
 		decoder->set_fup_mwait = false;
-		decoder->state.type = INTEL_PT_MWAIT_OP;
-		decoder->state.from_ip = decoder->ip;
-		decoder->state.to_ip = 0;
+		decoder->state.type |= INTEL_PT_MWAIT_OP;
 		decoder->state.mwait_payload = decoder->fup_mwait_payload;
 		ret = true;
 	}
 	if (decoder->set_fup_pwre) {
 		decoder->set_fup_pwre = false;
 		decoder->state.type |= INTEL_PT_PWR_ENTRY;
-		decoder->state.type &= ~INTEL_PT_BRANCH;
-		decoder->state.from_ip = decoder->ip;
-		decoder->state.to_ip = 0;
 		decoder->state.pwre_payload = decoder->fup_pwre_payload;
 		ret = true;
 	}
 	if (decoder->set_fup_exstop) {
 		decoder->set_fup_exstop = false;
 		decoder->state.type |= INTEL_PT_EX_STOP;
-		decoder->state.type &= ~INTEL_PT_BRANCH;
 		decoder->state.flags |= INTEL_PT_FUP_IP;
-		decoder->state.from_ip = decoder->ip;
-		decoder->state.to_ip = 0;
 		ret = true;
 	}
 	if (decoder->set_fup_bep) {
 		decoder->set_fup_bep = false;
 		decoder->state.type |= INTEL_PT_BLK_ITEMS;
-		decoder->state.type &= ~INTEL_PT_BRANCH;
+		ret = true;
+	}
+	if (decoder->overflow) {
+		decoder->overflow = false;
+		if (!ret && !decoder->pge) {
+			if (decoder->hop) {
+				decoder->state.type = 0;
+				decoder->pkt_state = INTEL_PT_STATE_RESAMPLE;
+			}
+			decoder->pge = true;
+			decoder->state.type |= INTEL_PT_BRANCH | INTEL_PT_TRACE_BEGIN;
+			decoder->state.from_ip = 0;
+			decoder->state.to_ip = decoder->ip;
+			return true;
+		}
+	}
+	if (ret) {
 		decoder->state.from_ip = decoder->ip;
 		decoder->state.to_ip = 0;
-		ret = true;
+	} else {
+		decoder->state.type = type;
 	}
 	return ret;
 }
@@ -1394,17 +1409,108 @@
 	return intel_pt_bug(decoder);
 }
 
+struct eptw_data {
+	int bit_countdown;
+	uint64_t payload;
+};
+
+static int intel_pt_eptw_lookahead_cb(struct intel_pt_pkt_info *pkt_info)
+{
+	struct eptw_data *data = pkt_info->data;
+	int nr_bits;
+
+	switch (pkt_info->packet.type) {
+	case INTEL_PT_PAD:
+	case INTEL_PT_MNT:
+	case INTEL_PT_MODE_EXEC:
+	case INTEL_PT_MODE_TSX:
+	case INTEL_PT_MTC:
+	case INTEL_PT_FUP:
+	case INTEL_PT_CYC:
+	case INTEL_PT_CBR:
+	case INTEL_PT_TSC:
+	case INTEL_PT_TMA:
+	case INTEL_PT_PIP:
+	case INTEL_PT_VMCS:
+	case INTEL_PT_PSB:
+	case INTEL_PT_PSBEND:
+	case INTEL_PT_PTWRITE:
+	case INTEL_PT_PTWRITE_IP:
+	case INTEL_PT_EXSTOP:
+	case INTEL_PT_EXSTOP_IP:
+	case INTEL_PT_MWAIT:
+	case INTEL_PT_PWRE:
+	case INTEL_PT_PWRX:
+	case INTEL_PT_BBP:
+	case INTEL_PT_BIP:
+	case INTEL_PT_BEP:
+	case INTEL_PT_BEP_IP:
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+	case INTEL_PT_EVD:
+		break;
+
+	case INTEL_PT_TNT:
+		nr_bits = data->bit_countdown;
+		if (nr_bits > pkt_info->packet.count)
+			nr_bits = pkt_info->packet.count;
+		data->payload <<= nr_bits;
+		data->payload |= pkt_info->packet.payload >> (64 - nr_bits);
+		data->bit_countdown -= nr_bits;
+		return !data->bit_countdown;
+
+	case INTEL_PT_TIP_PGE:
+	case INTEL_PT_TIP_PGD:
+	case INTEL_PT_TIP:
+	case INTEL_PT_BAD:
+	case INTEL_PT_OVF:
+	case INTEL_PT_TRACESTOP:
+	default:
+		return 1;
+	}
+
+	return 0;
+}
+
+static int intel_pt_emulated_ptwrite(struct intel_pt_decoder *decoder)
+{
+	int n = 64 - decoder->tnt.count;
+	struct eptw_data data = {
+		.bit_countdown = n,
+		.payload = decoder->tnt.payload >> n,
+	};
+
+	decoder->emulated_ptwrite = false;
+	intel_pt_log("Emulated ptwrite detected\n");
+
+	intel_pt_pkt_lookahead(decoder, intel_pt_eptw_lookahead_cb, &data);
+	if (data.bit_countdown)
+		return -ECONNRESET;
+
+	decoder->state.type = INTEL_PT_PTW;
+	decoder->state.from_ip = decoder->ip;
+	decoder->state.to_ip = 0;
+	decoder->state.ptw_payload = data.payload;
+	return 0;
+}
+
 static int intel_pt_walk_tnt(struct intel_pt_decoder *decoder)
 {
 	struct intel_pt_insn intel_pt_insn;
 	int err;
 
 	while (1) {
+		if (decoder->emulated_ptwrite)
+			return intel_pt_emulated_ptwrite(decoder);
 		err = intel_pt_walk_insn(decoder, &intel_pt_insn, 0);
-		if (err == INTEL_PT_RETURN)
+		if (err == INTEL_PT_RETURN) {
+			decoder->emulated_ptwrite = intel_pt_insn.emulated_ptwrite;
 			return 0;
-		if (err)
+		}
+		if (err) {
+			decoder->emulated_ptwrite = false;
 			return err;
+		}
 
 		if (intel_pt_insn.op == INTEL_PT_OP_RET) {
 			if (!decoder->return_compression) {
@@ -1607,7 +1713,16 @@
 	intel_pt_clear_tx_flags(decoder);
 	intel_pt_set_nr(decoder);
 	decoder->timestamp_insn_cnt = 0;
-	decoder->pkt_state = INTEL_PT_STATE_ERR_RESYNC;
+	decoder->pkt_state = INTEL_PT_STATE_IN_SYNC;
+	decoder->state.from_ip = decoder->ip;
+	decoder->ip = 0;
+	decoder->pge = false;
+	decoder->set_fup_tx_flags = false;
+	decoder->set_fup_ptw = false;
+	decoder->set_fup_mwait = false;
+	decoder->set_fup_pwre = false;
+	decoder->set_fup_exstop = false;
+	decoder->set_fup_bep = false;
 	decoder->overflow = true;
 	return -EOVERFLOW;
 }
@@ -1744,6 +1859,8 @@
 
 	decoder->cbr = cbr;
 	decoder->cbr_cyc_to_tsc = decoder->max_non_turbo_ratio_fp / cbr;
+	decoder->cyc_ref_timestamp = decoder->timestamp;
+	decoder->cycle_cnt = 0;
 
 	intel_pt_mtc_cyc_cnt_cbr(decoder);
 }
@@ -1855,6 +1972,9 @@
 		case INTEL_PT_BIP:
 		case INTEL_PT_BEP:
 		case INTEL_PT_BEP_IP:
+		case INTEL_PT_CFE:
+		case INTEL_PT_CFE_IP:
+		case INTEL_PT_EVD:
 			decoder->have_tma = false;
 			intel_pt_log("ERROR: Unexpected packet\n");
 			err = -EAGAIN;
@@ -1957,6 +2077,9 @@
 		case INTEL_PT_BIP:
 		case INTEL_PT_BEP:
 		case INTEL_PT_BEP_IP:
+		case INTEL_PT_CFE:
+		case INTEL_PT_CFE_IP:
+		case INTEL_PT_EVD:
 			intel_pt_log("ERROR: Missing TIP after FUP\n");
 			decoder->pkt_state = INTEL_PT_STATE_ERR3;
 			decoder->pkt_step = 0;
@@ -2116,6 +2239,9 @@
 	case INTEL_PT_TIP:
 	case INTEL_PT_PSB:
 	case INTEL_PT_TRACESTOP:
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+	case INTEL_PT_EVD:
 	default:
 		return 1;
 	}
@@ -2635,6 +2761,9 @@
 			decoder->blk_type = 0;
 			break;
 
+		case INTEL_PT_CFE:
+		case INTEL_PT_CFE_IP:
+		case INTEL_PT_EVD:
 		case INTEL_PT_MODE_EXEC:
 		case INTEL_PT_MODE_TSX:
 		case INTEL_PT_MNT:
@@ -2665,6 +2794,8 @@
 /* Hop mode: Ignore TNT, do not walk code, but get ip from FUPs and TIPs */
 static int intel_pt_hop_trace(struct intel_pt_decoder *decoder, bool *no_tip, int *err)
 {
+	*err = 0;
+
 	/* Leap from PSB to PSB, getting ip from FUP within PSB+ */
 	if (decoder->leap && !decoder->in_psb && decoder->packet.type != INTEL_PT_PSB) {
 		*err = intel_pt_scan_for_psb(decoder);
@@ -2677,6 +2808,7 @@
 		return HOP_IGNORE;
 
 	case INTEL_PT_TIP_PGD:
+		decoder->pge = false;
 		if (!decoder->packet.count) {
 			intel_pt_set_nr(decoder);
 			return HOP_IGNORE;
@@ -2704,18 +2836,21 @@
 		if (!decoder->packet.count)
 			return HOP_IGNORE;
 		intel_pt_set_ip(decoder);
-		if (intel_pt_fup_event(decoder))
-			return HOP_RETURN;
-		if (!decoder->branch_enable)
+		if (decoder->set_fup_mwait || decoder->set_fup_pwre)
+			*no_tip = true;
+		if (!decoder->branch_enable || !decoder->pge)
 			*no_tip = true;
 		if (*no_tip) {
 			decoder->state.type = INTEL_PT_INSTRUCTION;
 			decoder->state.from_ip = decoder->ip;
 			decoder->state.to_ip = 0;
+			intel_pt_fup_event(decoder);
 			return HOP_RETURN;
 		}
+		intel_pt_fup_event(decoder);
+		decoder->state.type |= INTEL_PT_INSTRUCTION | INTEL_PT_BRANCH;
 		*err = intel_pt_walk_fup_tip(decoder);
-		if (!*err)
+		if (!*err && decoder->state.to_ip)
 			decoder->pkt_state = INTEL_PT_STATE_RESAMPLE;
 		return HOP_RETURN;
 
@@ -2765,6 +2900,9 @@
 	case INTEL_PT_BIP:
 	case INTEL_PT_BEP:
 	case INTEL_PT_BEP_IP:
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+	case INTEL_PT_EVD:
 	default:
 		return HOP_PROCESS;
 	}
@@ -2833,6 +2971,9 @@
 	case INTEL_PT_BIP:
 	case INTEL_PT_BEP:
 	case INTEL_PT_BEP_IP:
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+	case INTEL_PT_EVD:
 		if (data->after_psbend) {
 			data->after_psbend -= 1;
 			if (!data->after_psbend)
@@ -2896,7 +3037,7 @@
 {
 	struct intel_pt_psb_info data = { .fup = false };
 
-	if (!decoder->branch_enable || !decoder->pge)
+	if (!decoder->branch_enable)
 		return false;
 
 	intel_pt_pkt_lookahead(decoder, intel_pt_psb_lookahead_cb, &data);
@@ -2923,6 +3064,7 @@
 		if (err)
 			return err;
 next:
+		err = 0;
 		if (decoder->cyc_threshold) {
 			if (decoder->sample_cyc && last_packet_type != INTEL_PT_CYC)
 				decoder->sample_cyc = false;
@@ -2961,6 +3103,7 @@
 
 		case INTEL_PT_TIP_PGE: {
 			decoder->pge = true;
+			decoder->overflow = false;
 			intel_pt_mtc_cyc_cnt_pge(decoder);
 			intel_pt_set_nr(decoder);
 			if (decoder->packet.count == 0) {
@@ -2998,7 +3141,7 @@
 				break;
 			}
 			intel_pt_set_last_ip(decoder);
-			if (!decoder->branch_enable) {
+			if (!decoder->branch_enable || !decoder->pge) {
 				decoder->ip = decoder->last_ip;
 				if (intel_pt_fup_event(decoder))
 					return 0;
@@ -3197,6 +3340,11 @@
 			}
 			goto next;
 
+		case INTEL_PT_CFE:
+		case INTEL_PT_CFE_IP:
+		case INTEL_PT_EVD:
+			break;
+
 		default:
 			return intel_pt_bug(decoder);
 		}
@@ -3239,6 +3387,9 @@
 		case INTEL_PT_BIP:
 		case INTEL_PT_BEP:
 		case INTEL_PT_BEP_IP:
+		case INTEL_PT_CFE:
+		case INTEL_PT_CFE_IP:
+		case INTEL_PT_EVD:
 			intel_pt_log("ERROR: Unexpected packet\n");
 			err = -ENOENT;
 			goto out;
@@ -3450,6 +3601,9 @@
 		case INTEL_PT_BIP:
 		case INTEL_PT_BEP:
 		case INTEL_PT_BEP_IP:
+		case INTEL_PT_CFE:
+		case INTEL_PT_CFE_IP:
+		case INTEL_PT_EVD:
 		default:
 			break;
 		}
@@ -3466,10 +3620,10 @@
 	decoder->set_fup_pwre = false;
 	decoder->set_fup_exstop = false;
 	decoder->set_fup_bep = false;
+	decoder->overflow = false;
 
 	if (!decoder->branch_enable) {
 		decoder->pkt_state = INTEL_PT_STATE_IN_SYNC;
-		decoder->overflow = false;
 		decoder->state.type = 0; /* Do not have a sample */
 		return 0;
 	}
@@ -3484,7 +3638,6 @@
 		decoder->pkt_state = INTEL_PT_STATE_RESAMPLE;
 	else
 		decoder->pkt_state = INTEL_PT_STATE_IN_SYNC;
-	decoder->overflow = false;
 
 	decoder->state.from_ip = 0;
 	decoder->state.to_ip = decoder->ip;
@@ -3606,7 +3759,7 @@
 	}
 
 	decoder->have_last_ip = true;
-	decoder->pkt_state = INTEL_PT_STATE_NO_IP;
+	decoder->pkt_state = INTEL_PT_STATE_IN_SYNC;
 
 	err = intel_pt_walk_psb(decoder);
 	if (err)
@@ -3703,7 +3856,8 @@
 
 	if (err) {
 		decoder->state.err = intel_pt_ext_err(err);
-		decoder->state.from_ip = decoder->ip;
+		if (err != -EOVERFLOW)
+			decoder->state.from_ip = decoder->ip;
 		intel_pt_update_sample_time(decoder);
 		decoder->sample_tot_cyc_cnt = decoder->tot_cyc_cnt;
 		intel_pt_set_nr(decoder);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/intel-pt-decoder.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/intel-pt-decoder.h
@@ -55,6 +55,7 @@
 	INTEL_PT_ERR_LOST,
 	INTEL_PT_ERR_UNK,
 	INTEL_PT_ERR_NELOOP,
+	INTEL_PT_ERR_EPTW,
 	INTEL_PT_ERR_MAX,
 };
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/intel-pt-insn-decoder.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/intel-pt-insn-decoder.c
@@ -32,6 +32,7 @@
 	int ext;
 
 	intel_pt_insn->rel = 0;
+	intel_pt_insn->emulated_ptwrite = false;
 
 	if (insn_is_avx(insn)) {
 		intel_pt_insn->op = INTEL_PT_OP_OTHER;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/intel-pt-insn-decoder.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/intel-pt-insn-decoder.h
@@ -37,6 +37,7 @@
 struct intel_pt_insn {
 	enum intel_pt_insn_op		op;
 	enum intel_pt_insn_branch	branch;
+	bool				emulated_ptwrite;
 	int				length;
 	int32_t				rel;
 	unsigned char			buf[INTEL_PT_INSN_BUF_SZ];
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/intel-pt-pkt-decoder.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/intel-pt-pkt-decoder.c
@@ -64,6 +64,9 @@
 	[INTEL_PT_BIP]		= "BIP",
 	[INTEL_PT_BEP]		= "BEP",
 	[INTEL_PT_BEP_IP]	= "BEP",
+	[INTEL_PT_CFE]		= "CFE",
+	[INTEL_PT_CFE_IP]	= "CFE",
+	[INTEL_PT_EVD]		= "EVD",
 };
 
 const char *intel_pt_pkt_name(enum intel_pt_pkt_type type)
@@ -329,6 +332,29 @@
 	return 2;
 }
 
+static int intel_pt_get_cfe(const unsigned char *buf, size_t len,
+			    struct intel_pt_pkt *packet)
+{
+	if (len < 4)
+		return INTEL_PT_NEED_MORE_BYTES;
+	packet->type = buf[2] & 0x80 ? INTEL_PT_CFE_IP : INTEL_PT_CFE;
+	packet->count = buf[2] & 0x1f;
+	packet->payload = buf[3];
+	return 4;
+}
+
+static int intel_pt_get_evd(const unsigned char *buf, size_t len,
+			    struct intel_pt_pkt *packet)
+{
+	if (len < 11)
+		return INTEL_PT_NEED_MORE_BYTES;
+	packet->type = INTEL_PT_EVD;
+	packet->count = buf[2] & 0x3f;
+	packet->payload = buf[3];
+	memcpy_le64(&packet->payload, buf + 3, 8);
+	return 11;
+}
+
 static int intel_pt_get_ext(const unsigned char *buf, size_t len,
 			    struct intel_pt_pkt *packet)
 {
@@ -375,6 +401,10 @@
 		return intel_pt_get_bep(len, packet);
 	case 0xb3: /* BEP with IP */
 		return intel_pt_get_bep_ip(len, packet);
+	case 0x13: /* CFE */
+		return intel_pt_get_cfe(buf, len, packet);
+	case 0x53: /* EVD */
+		return intel_pt_get_evd(buf, len, packet);
 	default:
 		return INTEL_PT_BAD_PACKET;
 	}
@@ -624,6 +654,9 @@
 	case INTEL_PT_MWAIT:
 	case INTEL_PT_BEP:
 	case INTEL_PT_BEP_IP:
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+	case INTEL_PT_EVD:
 		*ctx = INTEL_PT_NO_CTX;
 		break;
 	case INTEL_PT_BBP:
@@ -751,6 +784,13 @@
 	case INTEL_PT_BIP:
 		return snprintf(buf, buf_len, "%s ID 0x%02x Value 0x%llx",
 				name, packet->count, payload);
+	case INTEL_PT_CFE:
+	case INTEL_PT_CFE_IP:
+		return snprintf(buf, buf_len, "%s IP:%d Type 0x%02x Vector 0x%llx",
+				name, packet->type == INTEL_PT_CFE_IP, packet->count, payload);
+	case INTEL_PT_EVD:
+		return snprintf(buf, buf_len, "%s Type 0x%02x Payload 0x%llx",
+				name, packet->count, payload);
 	default:
 		break;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt-decoder/intel-pt-pkt-decoder.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt-decoder/intel-pt-pkt-decoder.h
@@ -56,6 +56,9 @@
 	INTEL_PT_BIP,
 	INTEL_PT_BEP,
 	INTEL_PT_BEP_IP,
+	INTEL_PT_CFE,
+	INTEL_PT_CFE_IP,
+	INTEL_PT_EVD,
 };
 
 struct intel_pt_pkt {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/intel-pt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/intel-pt.c
@@ -506,6 +506,7 @@
 	u64				byte_cnt;
 	enum intel_pt_insn_op		op;
 	enum intel_pt_insn_branch	branch;
+	bool				emulated_ptwrite;
 	int				length;
 	int32_t				rel;
 	char				insn[INTEL_PT_INSN_BUF_SZ];
@@ -592,6 +593,7 @@
 	e->byte_cnt = byte_cnt;
 	e->op = intel_pt_insn->op;
 	e->branch = intel_pt_insn->branch;
+	e->emulated_ptwrite = intel_pt_insn->emulated_ptwrite;
 	e->length = intel_pt_insn->length;
 	e->rel = intel_pt_insn->rel;
 	memcpy(e->insn, intel_pt_insn->buf, INTEL_PT_INSN_BUF_SZ);
@@ -678,6 +680,28 @@
 	return 0;
 }
 
+static inline bool intel_pt_jmp_16(struct intel_pt_insn *intel_pt_insn)
+{
+	return intel_pt_insn->rel == 16 && intel_pt_insn->branch == INTEL_PT_BR_UNCONDITIONAL;
+}
+
+#define PTWRITE_MAGIC		"\x0f\x0bperf,ptwrite  "
+#define PTWRITE_MAGIC_LEN	16
+
+static bool intel_pt_emulated_ptwrite(struct dso *dso, struct machine *machine, u64 offset)
+{
+	unsigned char buf[PTWRITE_MAGIC_LEN];
+	ssize_t len;
+
+	len = dso__data_read_offset(dso, machine, offset, buf, PTWRITE_MAGIC_LEN);
+	if (len == PTWRITE_MAGIC_LEN && !memcmp(buf, PTWRITE_MAGIC, PTWRITE_MAGIC_LEN)) {
+		intel_pt_log("Emulated ptwrite signature found\n");
+		return true;
+	}
+	intel_pt_log("Emulated ptwrite signature not found\n");
+	return false;
+}
+
 static int intel_pt_walk_next_insn(struct intel_pt_insn *intel_pt_insn,
 				   uint64_t *insn_cnt_ptr, uint64_t *ip,
 				   uint64_t to_ip, uint64_t max_insn_cnt,
@@ -740,6 +764,7 @@
 				*ip += e->byte_cnt;
 				intel_pt_insn->op = e->op;
 				intel_pt_insn->branch = e->branch;
+				intel_pt_insn->emulated_ptwrite = e->emulated_ptwrite;
 				intel_pt_insn->length = e->length;
 				intel_pt_insn->rel = e->rel;
 				memcpy(intel_pt_insn->buf, e->insn,
@@ -771,8 +796,18 @@
 
 			insn_cnt += 1;
 
-			if (intel_pt_insn->branch != INTEL_PT_BR_NO_BRANCH)
+			if (intel_pt_insn->branch != INTEL_PT_BR_NO_BRANCH) {
+				bool eptw;
+				u64 offs;
+
+				if (!intel_pt_jmp_16(intel_pt_insn))
+					goto out;
+				/* Check for emulated ptwrite */
+				offs = offset + intel_pt_insn->length;
+				eptw = intel_pt_emulated_ptwrite(al.map->dso, machine, offs);
+				intel_pt_insn->emulated_ptwrite = eptw;
 				goto out;
+			}
 
 			if (max_insn_cnt && insn_cnt >= max_insn_cnt)
 				goto out_no_cache;
@@ -1311,9 +1346,11 @@
 	} else if (ptq->state->flags & INTEL_PT_ASYNC) {
 		if (!ptq->state->to_ip)
 			ptq->flags = PERF_IP_FLAG_BRANCH |
+				     PERF_IP_FLAG_ASYNC |
 				     PERF_IP_FLAG_TRACE_END;
 		else if (ptq->state->from_nr && !ptq->state->to_nr)
 			ptq->flags = PERF_IP_FLAG_BRANCH | PERF_IP_FLAG_CALL |
+				     PERF_IP_FLAG_ASYNC |
 				     PERF_IP_FLAG_VMEXIT;
 		else
 			ptq->flags = PERF_IP_FLAG_BRANCH | PERF_IP_FLAG_CALL |
@@ -2510,6 +2547,7 @@
 				ptq->sync_switch = false;
 				intel_pt_next_tid(pt, ptq);
 			}
+			ptq->timestamp = state->est_timestamp;
 			if (pt->synth_opts.errors) {
 				err = intel_ptq_synth_error(ptq, state);
 				if (err)
@@ -3539,6 +3577,7 @@
 		*args = p;
 		return 0;
 	}
+	p += 1;
 	while (1) {
 		vmcs = strtoull(p, &p, 0);
 		if (errno)
@@ -3589,6 +3628,7 @@
 	[INTEL_PT_SNAPSHOT_MODE]	= "  Snapshot mode       %"PRId64"\n",
 	[INTEL_PT_PER_CPU_MMAPS]	= "  Per-cpu maps        %"PRId64"\n",
 	[INTEL_PT_MTC_BIT]		= "  MTC bit             %#"PRIx64"\n",
+	[INTEL_PT_MTC_FREQ_BITS]	= "  MTC freq bits       %#"PRIx64"\n",
 	[INTEL_PT_TSC_CTC_N]		= "  TSC:CTC numerator   %"PRIu64"\n",
 	[INTEL_PT_TSC_CTC_D]		= "  TSC:CTC denominator %"PRIu64"\n",
 	[INTEL_PT_CYC_BIT]		= "  CYC bit             %#"PRIx64"\n",
@@ -3603,8 +3643,12 @@
 	if (!dump_trace)
 		return;
 
-	for (i = start; i <= finish; i++)
-		fprintf(stdout, intel_pt_info_fmts[i], arr[i]);
+	for (i = start; i <= finish; i++) {
+		const char *fmt = intel_pt_info_fmts[i];
+
+		if (fmt)
+			fprintf(stdout, fmt, arr[i]);
+	}
 }
 
 static void intel_pt_print_info_str(const char *name, const char *str)
@@ -3900,6 +3944,12 @@
 
 	intel_pt_setup_pebs_events(pt);
 
+	if (perf_data__is_pipe(session->data)) {
+		pr_warning("WARNING: Intel PT with pipe mode is not recommended.\n"
+			   "         The output cannot relied upon.  In particular,\n"
+			   "         timestamps and the order of events may be incorrect.\n");
+	}
+
 	if (pt->sampling_mode || list_empty(&session->auxtrace_index))
 		err = auxtrace_queue_data(session, true, true);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/llvm-utils.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/llvm-utils.c
@@ -531,14 +531,37 @@
 
 	pr_debug("llvm compiling command template: %s\n", template);
 
+	/*
+	 * Below, substitute control characters for values that can cause the
+	 * echo to misbehave, then substitute the values back.
+	 */
 	err = -ENOMEM;
-	if (asprintf(&command_echo, "echo -n \"%s\"", template) < 0)
+	if (asprintf(&command_echo, "echo -n \a%s\a", template) < 0)
 		goto errout;
 
+#define SWAP_CHAR(a, b) do { if (*p == a) *p = b; } while (0)
+	for (char *p = command_echo; *p; p++) {
+		SWAP_CHAR('<', '\001');
+		SWAP_CHAR('>', '\002');
+		SWAP_CHAR('"', '\003');
+		SWAP_CHAR('\'', '\004');
+		SWAP_CHAR('|', '\005');
+		SWAP_CHAR('&', '\006');
+		SWAP_CHAR('\a', '"');
+	}
 	err = read_from_pipe(command_echo, (void **) &command_out, NULL);
 	if (err)
 		goto errout;
 
+	for (char *p = command_out; *p; p++) {
+		SWAP_CHAR('\001', '<');
+		SWAP_CHAR('\002', '>');
+		SWAP_CHAR('\003', '"');
+		SWAP_CHAR('\004', '\'');
+		SWAP_CHAR('\005', '|');
+		SWAP_CHAR('\006', '&');
+	}
+#undef SWAP_CHAR
 	pr_debug("llvm compiling command : %s\n", command_out);
 
 	err = read_from_pipe(template, &obj_buf, &obj_buf_sz);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/machine.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/machine.c
@@ -16,6 +16,7 @@
 #include "map_symbol.h"
 #include "branch.h"
 #include "mem-events.h"
+#include "path.h"
 #include "srcline.h"
 #include "symbol.h"
 #include "sort.h"
@@ -1407,7 +1408,7 @@
 		struct stat st;
 
 		/*sshfs might return bad dent->d_type, so we have to stat*/
-		snprintf(path, sizeof(path), "%s/%s", dir_name, dent->d_name);
+		path__join(path, sizeof(path), dir_name, dent->d_name);
 		if (stat(path, &st))
 			continue;
 
@@ -2436,16 +2437,18 @@
 		save_lbr_cursor_node(thread, cursor, i);
 	}
 
-	/* Add LBR ip from first entries.to */
-	ip = entries[0].to;
-	flags = &entries[0].flags;
-	*branch_from = entries[0].from;
-	err = add_callchain_ip(thread, cursor, parent,
-			       root_al, &cpumode, ip,
-			       true, flags, NULL,
-			       *branch_from);
-	if (err)
-		return err;
+	if (lbr_nr > 0) {
+		/* Add LBR ip from first entries.to */
+		ip = entries[0].to;
+		flags = &entries[0].flags;
+		*branch_from = entries[0].from;
+		err = add_callchain_ip(thread, cursor, parent,
+				root_al, &cpumode, ip,
+				true, flags, NULL,
+				*branch_from);
+		if (err)
+			return err;
+	}
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/parse-events.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/parse-events.c
@@ -196,9 +196,12 @@
 void parse_events__handle_error(struct parse_events_error *err, int idx,
 				char *str, char *help)
 {
-	if (WARN(!str, "WARNING: failed to provide error string\n")) {
-		free(help);
-		return;
+	if (WARN(!str, "WARNING: failed to provide error string\n"))
+		goto out_free;
+	if (!err) {
+		/* Assume caller does not want message printed */
+		pr_debug("event syntax error: %s\n", str);
+		goto out_free;
 	}
 	switch (err->num_errors) {
 	case 0:
@@ -224,6 +227,11 @@
 		break;
 	}
 	err->num_errors++;
+	return;
+
+out_free:
+	free(str);
+	free(help);
 }
 
 struct tracepoint_path *tracepoint_id_to_path(u64 config)
@@ -365,6 +373,9 @@
 	struct perf_cpu_map *cpus = pmu ? perf_cpu_map__get(pmu->cpus) :
 			       cpu_list ? perf_cpu_map__new(cpu_list) : NULL;
 
+	if (pmu)
+		perf_pmu__warn_invalid_formats(pmu);
+
 	if (pmu && attr->type == PERF_TYPE_RAW)
 		perf_pmu__warn_invalid_config(pmu, attr->config, name);
 
@@ -1529,7 +1540,9 @@
 	bool use_uncore_alias;
 	LIST_HEAD(config_terms);
 
-	if (verbose > 1) {
+	pmu = parse_state->fake_pmu ?: perf_pmu__find(name);
+
+	if (verbose > 1 && !(pmu && pmu->selectable)) {
 		fprintf(stderr, "Attempting to add event pmu '%s' with '",
 			name);
 		if (head_config) {
@@ -1542,7 +1555,6 @@
 		fprintf(stderr, "' that may result in non-fatal errors\n");
 	}
 
-	pmu = parse_state->fake_pmu ?: perf_pmu__find(name);
 	if (!pmu) {
 		char *err_str;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/parse-events.y
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/parse-events.y
@@ -183,6 +183,11 @@
 	err = parse_events__modifier_group(list, $3);
 	free($3);
 	if (err) {
+		struct parse_events_state *parse_state = _parse_state;
+		struct parse_events_error *error = parse_state->error;
+
+		parse_events__handle_error(error, @3.first_column,
+					   strdup("Bad modifier"), NULL);
 		free_list_evsel(list);
 		YYABORT;
 	}
@@ -240,6 +245,11 @@
 	err = parse_events__modifier_event(list, $2, false);
 	free($2);
 	if (err) {
+		struct parse_events_state *parse_state = _parse_state;
+		struct parse_events_error *error = parse_state->error;
+
+		parse_events__handle_error(error, @2.first_column,
+					   strdup("Bad modifier"), NULL);
 		free_list_evsel(list);
 		YYABORT;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/pmu.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/pmu.c
@@ -1048,6 +1048,23 @@
 	return NULL;
 }
 
+void perf_pmu__warn_invalid_formats(struct perf_pmu *pmu)
+{
+	struct perf_pmu_format *format;
+
+	/* fake pmu doesn't have format list */
+	if (pmu == &perf_pmu__fake)
+		return;
+
+	list_for_each_entry(format, &pmu->format, list)
+		if (format->value >= PERF_PMU_FORMAT_VALUE_CONFIG_END) {
+			pr_warning("WARNING: '%s' format '%s' requires 'perf_event_attr::config%d'"
+				   "which is not supported by this version of perf!\n",
+				   pmu->name, format->name, format->value);
+			return;
+		}
+}
+
 static struct perf_pmu *pmu_find(const char *name)
 {
 	struct perf_pmu *pmu;
@@ -1841,7 +1858,7 @@
 	return 0;
 
 free_name:
-	zfree(caps->name);
+	zfree(&caps->name);
 free_caps:
 	free(caps);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/pmu.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/pmu.h
@@ -17,6 +17,7 @@
 	PERF_PMU_FORMAT_VALUE_CONFIG,
 	PERF_PMU_FORMAT_VALUE_CONFIG1,
 	PERF_PMU_FORMAT_VALUE_CONFIG2,
+	PERF_PMU_FORMAT_VALUE_CONFIG_END,
 };
 
 #define PERF_PMU_FORMAT_BITS 64
@@ -135,6 +136,7 @@
 
 void perf_pmu__warn_invalid_config(struct perf_pmu *pmu, __u64 config,
 				   char *name);
+void perf_pmu__warn_invalid_formats(struct perf_pmu *pmu);
 
 bool perf_pmu__has_hybrid(void);
 int perf_pmu__match(char *pattern, char *name, char *tok);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/pmu.l
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/pmu.l
@@ -27,8 +27,6 @@
 
 {num_dec}	{ return value(10); }
 config		{ return PP_CONFIG; }
-config1		{ return PP_CONFIG1; }
-config2		{ return PP_CONFIG2; }
 -		{ return '-'; }
 :		{ return ':'; }
 ,		{ return ','; }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/pmu.y
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/pmu.y
@@ -20,7 +20,7 @@
 
 %}
 
-%token PP_CONFIG PP_CONFIG1 PP_CONFIG2
+%token PP_CONFIG
 %token PP_VALUE PP_ERROR
 %type <num> PP_VALUE
 %type <bits> bit_term
@@ -47,18 +47,11 @@
 				      $3));
 }
 |
-PP_CONFIG1 ':' bits
+PP_CONFIG PP_VALUE ':' bits
 {
 	ABORT_ON(perf_pmu__new_format(format, name,
-				      PERF_PMU_FORMAT_VALUE_CONFIG1,
-				      $3));
-}
-|
-PP_CONFIG2 ':' bits
-{
-	ABORT_ON(perf_pmu__new_format(format, name,
-				      PERF_PMU_FORMAT_VALUE_CONFIG2,
-				      $3));
+				      $2,
+				      $4));
 }
 
 bits:
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/probe-event.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/probe-event.c
@@ -1775,8 +1775,10 @@
 	if (!pev->event && pev->point.function && pev->point.line
 			&& !pev->point.lazy_line && !pev->point.offset) {
 		if (asprintf(&pev->event, "%s_L%d", pev->point.function,
-			pev->point.line) < 0)
-			return -ENOMEM;
+			pev->point.line) < 0) {
+			ret = -ENOMEM;
+			goto out;
+		}
 	}
 
 	/* Copy arguments and ensure return probe has no C argument */
@@ -3083,6 +3085,9 @@
 	for (j = 0; j < num_matched_functions; j++) {
 		sym = syms[j];
 
+		if (sym->type != STT_FUNC)
+			continue;
+
 		/* There can be duplicated symbols in the map */
 		for (i = 0; i < j; i++)
 			if (sym->start == syms[i]->start) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/probe-finder.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/probe-finder.c
@@ -1490,6 +1490,10 @@
 	if (ret >= 0 && tf.pf.skip_empty_arg)
 		ret = fill_empty_trace_arg(pev, tf.tevs, tf.ntevs);
 
+#if _ELFUTILS_PREREQ(0, 142)
+	dwarf_cfi_end(tf.pf.cfi_eh);
+#endif
+
 	if (ret < 0 || tf.ntevs == 0) {
 		for (i = 0; i < tf.ntevs; i++)
 			clear_probe_trace_event(&tf.tevs[i]);
@@ -1732,8 +1736,21 @@
 
 	/* Find a corresponding function (name, baseline and baseaddr) */
 	if (die_find_realfunc(&cudie, (Dwarf_Addr)addr, &spdie)) {
-		/* Get function entry information */
-		func = basefunc = dwarf_diename(&spdie);
+		/*
+		 * Get function entry information.
+		 *
+		 * As described in the document DWARF Debugging Information
+		 * Format Version 5, section 2.22 Linkage Names, "mangled names,
+		 * are used in various ways, ... to distinguish multiple
+		 * entities that have the same name".
+		 *
+		 * Firstly try to get distinct linkage name, if fail then
+		 * rollback to get associated name in DIE.
+		 */
+		func = basefunc = die_get_linkage_name(&spdie);
+		if (!func)
+			func = basefunc = dwarf_diename(&spdie);
+
 		if (!func ||
 		    die_entrypc(&spdie, &baseaddr) != 0 ||
 		    dwarf_decl_line(&spdie, &baseline) != 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/probe-finder.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/probe-finder.h
@@ -81,9 +81,9 @@
 
 	/* For variable searching */
 #if _ELFUTILS_PREREQ(0, 142)
-	/* Call Frame Information from .eh_frame */
+	/* Call Frame Information from .eh_frame. Owned by this struct. */
 	Dwarf_CFI		*cfi_eh;
-	/* Call Frame Information from .debug_frame */
+	/* Call Frame Information from .debug_frame. Not owned. */
 	Dwarf_CFI		*cfi_dbg;
 #endif
 	Dwarf_Op		*fb_ops;	/* Frame base attribute */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/python.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/python.c
@@ -158,7 +158,7 @@
 };
 
 #define sample_members \
-	sample_member_def(sample_ip, ip, T_ULONGLONG, "event type"),			 \
+	sample_member_def(sample_ip, ip, T_ULONGLONG, "event ip"),			 \
 	sample_member_def(sample_pid, pid, T_INT, "event pid"),			 \
 	sample_member_def(sample_tid, tid, T_INT, "event tid"),			 \
 	sample_member_def(sample_time, time, T_ULONGLONG, "event timestamp"),		 \
@@ -585,6 +585,11 @@
 	      event->header.type == PERF_RECORD_SWITCH_CPU_WIDE))
 		return NULL;
 
+	// FIXME this better be dynamic or we need to parse everything
+	// before calling perf_mmap__consume(), including tracepoint fields.
+	if (sizeof(pevent->event) < event->header.size)
+		return NULL;
+
 	ptype = pyrf_event__type[event->header.type];
 	pevent = PyObject_New(struct pyrf_event, ptype);
 	if (pevent != NULL)
@@ -1084,20 +1089,22 @@
 
 		evsel = evlist__event2evsel(evlist, event);
 		if (!evsel) {
+			Py_DECREF(pyevent);
 			Py_INCREF(Py_None);
 			return Py_None;
 		}
 
 		pevent->evsel = evsel;
 
-		err = evsel__parse_sample(evsel, event, &pevent->sample);
-
-		/* Consume the even only after we parsed it out. */
 		perf_mmap__consume(&md->core);
 
-		if (err)
+		err = evsel__parse_sample(evsel, &pevent->event, &pevent->sample);
+		if (err) {
+			Py_DECREF(pyevent);
 			return PyErr_Format(PyExc_OSError,
 					    "perf: can't parse sample, err=%d", err);
+		}
+
 		return pyevent;
 	}
 end:
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/session.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/session.c
@@ -2076,6 +2076,7 @@
 	       bool needs_swap, union perf_event *error)
 {
 	union perf_event *event;
+	u16 event_size;
 
 	/*
 	 * Ensure we have enough space remaining to read
@@ -2088,15 +2089,23 @@
 	if (needs_swap)
 		perf_event_header__bswap(&event->header);
 
-	if (head + event->header.size <= mmap_size)
+	event_size = event->header.size;
+	if (head + event_size <= mmap_size)
 		return event;
 
 	/* We're not fetching the event so swap back again */
 	if (needs_swap)
 		perf_event_header__bswap(&event->header);
 
-	pr_debug("%s: head=%#" PRIx64 " event->header_size=%#x, mmap_size=%#zx:"
-		 " fuzzed or compressed perf.data?\n",__func__, head, event->header.size, mmap_size);
+	/* Check if the event fits into the next mmapped buf. */
+	if (event_size <= mmap_size - head % page_size) {
+		/* Remap buf and fetch again. */
+		return NULL;
+	}
+
+	/* Invalid input. Event size should never exceed mmap_size. */
+	pr_debug("%s: head=%#" PRIx64 " event->header.size=%#x, mmap_size=%#zx:"
+		 " fuzzed or compressed perf.data?\n", __func__, head, event_size, mmap_size);
 
 	return error;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/setup.py
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/setup.py
@@ -1,12 +1,14 @@
-from os import getenv
+from os import getenv, path
 from subprocess import Popen, PIPE
 from re import sub
 
 cc = getenv("CC")
 cc_is_clang = b"clang version" in Popen([cc.split()[0], "-v"], stderr=PIPE).stderr.readline()
+src_feature_tests  = getenv('srctree') + '/tools/build/feature'
 
 def clang_has_option(option):
-    return [o for o in Popen([cc, option], stderr=PIPE).stderr.readlines() if b"unknown argument" in o] == [ ]
+    cc_output = Popen([cc, option, path.join(src_feature_tests, "test-hello.c") ], stderr=PIPE).stderr.readlines()
+    return [o for o in cc_output if ((b"unknown argument" in o) or (b"is not supported" in o))] == [ ]
 
 if cc_is_clang:
     from distutils.sysconfig import get_config_vars
@@ -23,6 +25,8 @@
             vars[var] = sub("-fstack-protector-strong", "", vars[var])
         if not clang_has_option("-fno-semantic-interposition"):
             vars[var] = sub("-fno-semantic-interposition", "", vars[var])
+        if not clang_has_option("-ffat-lto-objects"):
+            vars[var] = sub("-ffat-lto-objects", "", vars[var])
 
 from distutils.core import setup, Extension
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/smt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/smt.c
@@ -15,7 +15,7 @@
 	if (cached)
 		return cached_result;
 
-	if (sysfs__read_int("devices/system/cpu/smt/active", &cached_result) > 0)
+	if (sysfs__read_int("devices/system/cpu/smt/active", &cached_result) >= 0)
 		goto done;
 
 	ncpu = sysconf(_SC_NPROCESSORS_CONF);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/sort.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/sort.c
@@ -275,7 +275,7 @@
 	 * comparing symbol address alone is not enough since it's a
 	 * relative address within a dso.
 	 */
-	if (!hists__has(left->hists, dso) || hists__has(right->hists, dso)) {
+	if (!hists__has(left->hists, dso)) {
 		ret = sort__dso_cmp(left, right);
 		if (ret != 0)
 			return ret;
@@ -876,8 +876,7 @@
 static int64_t
 sort__sym_from_cmp(struct hist_entry *left, struct hist_entry *right)
 {
-	struct addr_map_symbol *from_l = &left->branch_info->from;
-	struct addr_map_symbol *from_r = &right->branch_info->from;
+	struct addr_map_symbol *from_l, *from_r;
 
 	if (!left->branch_info || !right->branch_info)
 		return cmp_null(left->branch_info, right->branch_info);
@@ -1325,88 +1324,68 @@
 	.se_width_idx	= HISTC_MISPREDICT,
 };
 
-static u64 he_weight(struct hist_entry *he)
-{
-	return he->stat.nr_events ? he->stat.weight / he->stat.nr_events : 0;
-}
-
 static int64_t
-sort__local_weight_cmp(struct hist_entry *left, struct hist_entry *right)
+sort__weight_cmp(struct hist_entry *left, struct hist_entry *right)
 {
-	return he_weight(left) - he_weight(right);
+	return left->weight - right->weight;
 }
 
 static int hist_entry__local_weight_snprintf(struct hist_entry *he, char *bf,
 				    size_t size, unsigned int width)
 {
-	return repsep_snprintf(bf, size, "%-*llu", width, he_weight(he));
+	return repsep_snprintf(bf, size, "%-*llu", width, he->weight);
 }
 
 struct sort_entry sort_local_weight = {
 	.se_header	= "Local Weight",
-	.se_cmp		= sort__local_weight_cmp,
+	.se_cmp		= sort__weight_cmp,
 	.se_snprintf	= hist_entry__local_weight_snprintf,
 	.se_width_idx	= HISTC_LOCAL_WEIGHT,
 };
 
-static int64_t
-sort__global_weight_cmp(struct hist_entry *left, struct hist_entry *right)
-{
-	return left->stat.weight - right->stat.weight;
-}
-
 static int hist_entry__global_weight_snprintf(struct hist_entry *he, char *bf,
 					      size_t size, unsigned int width)
 {
-	return repsep_snprintf(bf, size, "%-*llu", width, he->stat.weight);
+	return repsep_snprintf(bf, size, "%-*llu", width,
+			       he->weight * he->stat.nr_events);
 }
 
 struct sort_entry sort_global_weight = {
 	.se_header	= "Weight",
-	.se_cmp		= sort__global_weight_cmp,
+	.se_cmp		= sort__weight_cmp,
 	.se_snprintf	= hist_entry__global_weight_snprintf,
 	.se_width_idx	= HISTC_GLOBAL_WEIGHT,
 };
 
-static u64 he_ins_lat(struct hist_entry *he)
-{
-		return he->stat.nr_events ? he->stat.ins_lat / he->stat.nr_events : 0;
-}
-
 static int64_t
-sort__local_ins_lat_cmp(struct hist_entry *left, struct hist_entry *right)
+sort__ins_lat_cmp(struct hist_entry *left, struct hist_entry *right)
 {
-		return he_ins_lat(left) - he_ins_lat(right);
+	return left->ins_lat - right->ins_lat;
 }
 
 static int hist_entry__local_ins_lat_snprintf(struct hist_entry *he, char *bf,
 					      size_t size, unsigned int width)
 {
-		return repsep_snprintf(bf, size, "%-*u", width, he_ins_lat(he));
+	return repsep_snprintf(bf, size, "%-*u", width, he->ins_lat);
 }
 
 struct sort_entry sort_local_ins_lat = {
 	.se_header	= "Local INSTR Latency",
-	.se_cmp		= sort__local_ins_lat_cmp,
+	.se_cmp		= sort__ins_lat_cmp,
 	.se_snprintf	= hist_entry__local_ins_lat_snprintf,
 	.se_width_idx	= HISTC_LOCAL_INS_LAT,
 };
 
-static int64_t
-sort__global_ins_lat_cmp(struct hist_entry *left, struct hist_entry *right)
-{
-		return left->stat.ins_lat - right->stat.ins_lat;
-}
-
 static int hist_entry__global_ins_lat_snprintf(struct hist_entry *he, char *bf,
 					       size_t size, unsigned int width)
 {
-		return repsep_snprintf(bf, size, "%-*u", width, he->stat.ins_lat);
+	return repsep_snprintf(bf, size, "%-*u", width,
+			       he->ins_lat * he->stat.nr_events);
 }
 
 struct sort_entry sort_global_ins_lat = {
 	.se_header	= "INSTR Latency",
-	.se_cmp		= sort__global_ins_lat_cmp,
+	.se_cmp		= sort__ins_lat_cmp,
 	.se_snprintf	= hist_entry__global_ins_lat_snprintf,
 	.se_width_idx	= HISTC_GLOBAL_INS_LAT,
 };
@@ -1414,13 +1393,13 @@
 static int64_t
 sort__global_p_stage_cyc_cmp(struct hist_entry *left, struct hist_entry *right)
 {
-	return left->stat.p_stage_cyc - right->stat.p_stage_cyc;
+	return left->p_stage_cyc - right->p_stage_cyc;
 }
 
 static int hist_entry__p_stage_cyc_snprintf(struct hist_entry *he, char *bf,
 					size_t size, unsigned int width)
 {
-	return repsep_snprintf(bf, size, "%-*u", width, he->stat.p_stage_cyc);
+	return repsep_snprintf(bf, size, "%-*u", width, he->p_stage_cyc);
 }
 
 struct sort_entry sort_p_stage_cyc = {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/sort.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/sort.h
@@ -49,9 +49,6 @@
 	u64			period_us;
 	u64			period_guest_sys;
 	u64			period_guest_us;
-	u64			weight;
-	u64			ins_lat;
-	u64			p_stage_cyc;
 	u32			nr_events;
 };
 
@@ -109,6 +106,9 @@
 	s32			socket;
 	s32			cpu;
 	u64			code_page_size;
+	u64			weight;
+	u64			ins_lat;
+	u64			p_stage_cyc;
 	u8			cpumode;
 	u8			depth;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/stat-display.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/stat-display.c
@@ -207,7 +207,7 @@
 
 	fputc('\n', os->fh);
 	if (os->prefix)
-		fprintf(os->fh, "%s%s", os->prefix, config->csv_sep);
+		fprintf(os->fh, "%s", os->prefix);
 	aggr_printout(config, os->evsel, os->id, os->nr);
 	for (i = 0; i < os->nfields; i++)
 		fputs(config->csv_sep, os->fh);
@@ -275,7 +275,7 @@
 	if (color)
 		mlen += strlen(color) + sizeof(PERF_COLOR_RESET) - 1;
 
-	color_snprintf(str, sizeof(str), color ?: "", fmt, val);
+	color_snprintf(str, sizeof(str), color ?: "", fmt ?: "", val);
 	fprintf(out, "%*s ", mlen, str);
 }
 
@@ -584,15 +584,16 @@
 
 	alias = list_prepare_entry(counter, &(evlist->core.entries), core.node);
 	list_for_each_entry_continue (alias, &evlist->core.entries, core.node) {
-		if (strcmp(evsel__name(alias), evsel__name(counter)) ||
-		    alias->scale != counter->scale ||
-		    alias->cgrp != counter->cgrp ||
-		    strcmp(alias->unit, counter->unit) ||
-		    evsel__is_clock(alias) != evsel__is_clock(counter) ||
-		    !strcmp(alias->pmu_name, counter->pmu_name))
-			break;
-		alias->merged_stat = true;
-		cb(config, alias, data, false);
+		/* Merge events with the same name, etc. but on different PMUs. */
+		if (!strcmp(evsel__name(alias), evsel__name(counter)) &&
+			alias->scale == counter->scale &&
+			alias->cgrp == counter->cgrp &&
+			!strcmp(alias->unit, counter->unit) &&
+			evsel__is_clock(alias) == evsel__is_clock(counter) &&
+			strcmp(alias->pmu_name, counter->pmu_name)) {
+			alias->merged_stat = true;
+			cb(config, alias, data, false);
+		}
 	}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/stat.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/stat.c
@@ -576,11 +576,7 @@
 	if (evsel__is_group_leader(evsel)) {
 		attr->disabled = 1;
 
-		/*
-		 * In case of initial_delay we enable tracee
-		 * events manually.
-		 */
-		if (target__none(target) && !config->initial_delay)
+		if (target__enable_on_exec(target))
 			attr->enable_on_exec = 1;
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/stat.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/stat.h
@@ -137,7 +137,6 @@
 	FILE			*output;
 	unsigned int		 interval;
 	unsigned int		 timeout;
-	int			 initial_delay;
 	unsigned int		 unit_width;
 	unsigned int		 metric_only_len;
 	int			 times;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/symbol-elf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/symbol-elf.c
@@ -233,6 +233,33 @@
 	return NULL;
 }
 
+static int elf_read_program_header(Elf *elf, u64 vaddr, GElf_Phdr *phdr)
+{
+	size_t i, phdrnum;
+	u64 sz;
+
+	if (elf_getphdrnum(elf, &phdrnum))
+		return -1;
+
+	for (i = 0; i < phdrnum; i++) {
+		if (gelf_getphdr(elf, i, phdr) == NULL)
+			return -1;
+
+		if (phdr->p_type != PT_LOAD)
+			continue;
+
+		sz = max(phdr->p_memsz, phdr->p_filesz);
+		if (!sz)
+			continue;
+
+		if (vaddr >= phdr->p_vaddr && (vaddr < phdr->p_vaddr + sz))
+			return 0;
+	}
+
+	/* Not found any valid program header */
+	return -1;
+}
+
 static bool want_demangle(bool is_kernel_sym)
 {
 	return is_kernel_sym ? symbol_conf.demangle_kernel : symbol_conf.demangle;
@@ -526,7 +553,7 @@
 				size_t sz = min(size, descsz);
 				memcpy(bf, ptr, sz);
 				memset(bf + sz, 0, size - sz);
-				err = descsz;
+				err = sz;
 				break;
 			}
 		}
@@ -1209,6 +1236,7 @@
 					sym.st_value);
 			used_opd = true;
 		}
+
 		/*
 		 * When loading symbols in a data mapping, ABS symbols (which
 		 * has a value of SHN_ABS in its st_shndx) failed at
@@ -1262,11 +1290,33 @@
 				goto out_elf_end;
 		} else if ((used_opd && runtime_ss->adjust_symbols) ||
 			   (!used_opd && syms_ss->adjust_symbols)) {
-			pr_debug4("%s: adjusting symbol: st_value: %#" PRIx64 " "
-				  "sh_addr: %#" PRIx64 " sh_offset: %#" PRIx64 "\n", __func__,
-				  (u64)sym.st_value, (u64)shdr.sh_addr,
-				  (u64)shdr.sh_offset);
-			sym.st_value -= shdr.sh_addr - shdr.sh_offset;
+			GElf_Phdr phdr;
+
+			if (elf_read_program_header(runtime_ss->elf,
+						    (u64)sym.st_value, &phdr)) {
+				pr_debug4("%s: failed to find program header for "
+					   "symbol: %s st_value: %#" PRIx64 "\n",
+					   __func__, elf_name, (u64)sym.st_value);
+				pr_debug4("%s: adjusting symbol: st_value: %#" PRIx64 " "
+					"sh_addr: %#" PRIx64 " sh_offset: %#" PRIx64 "\n",
+					__func__, (u64)sym.st_value, (u64)shdr.sh_addr,
+					(u64)shdr.sh_offset);
+				/*
+				 * Fail to find program header, let's rollback
+				 * to use shdr.sh_addr and shdr.sh_offset to
+				 * calibrate symbol's file address, though this
+				 * is not necessary for normal C ELF file, we
+				 * still need to handle java JIT symbols in this
+				 * case.
+				 */
+				sym.st_value -= shdr.sh_addr - shdr.sh_offset;
+			} else {
+				pr_debug4("%s: adjusting symbol: st_value: %#" PRIx64 " "
+					"p_vaddr: %#" PRIx64 " p_offset: %#" PRIx64 "\n",
+					__func__, (u64)sym.st_value, (u64)phdr.p_vaddr,
+					(u64)phdr.p_offset);
+				sym.st_value -= phdr.p_vaddr - phdr.p_offset;
+			}
 		}
 
 		demangled = demangle_sym(dso, kmodule, elf_name);
@@ -1290,7 +1340,7 @@
 	 * For misannotated, zeroed, ASM function sizes.
 	 */
 	if (nr > 0) {
-		symbols__fixup_end(&dso->symbols);
+		symbols__fixup_end(&dso->symbols, false);
 		symbols__fixup_duplicate(&dso->symbols);
 		if (kmap) {
 			/*
@@ -2041,8 +2091,8 @@
  * unusual.  One significant peculiarity is that the mapping (start -> pgoff)
  * is not the same for the kernel map and the modules map.  That happens because
  * the data is copied adjacently whereas the original kcore has gaps.  Finally,
- * kallsyms and modules files are compared with their copies to check that
- * modules have not been loaded or unloaded while the copies were taking place.
+ * kallsyms file is compared with its copy to check that modules have not been
+ * loaded or unloaded while the copies were taking place.
  *
  * Return: %0 on success, %-1 on failure.
  */
@@ -2105,9 +2155,6 @@
 			goto out_extract_close;
 	}
 
-	if (kcore_copy__compare_file(from_dir, to_dir, "modules"))
-		goto out_extract_close;
-
 	if (kcore_copy__compare_file(from_dir, to_dir, "kallsyms"))
 		goto out_extract_close;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/symbol.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/symbol.c
@@ -101,11 +101,6 @@
 	return tail - str;
 }
 
-void __weak arch__symbols__fixup_end(struct symbol *p, struct symbol *c)
-{
-	p->end = c->start;
-}
-
 const char * __weak arch__normalize_symbol_name(const char *name)
 {
 	return name;
@@ -217,7 +212,8 @@
 	}
 }
 
-void symbols__fixup_end(struct rb_root_cached *symbols)
+/* Update zero-sized symbols using the address of the next symbol */
+void symbols__fixup_end(struct rb_root_cached *symbols, bool is_kallsyms)
 {
 	struct rb_node *nd, *prevnd = rb_first_cached(symbols);
 	struct symbol *curr, *prev;
@@ -231,8 +227,29 @@
 		prev = curr;
 		curr = rb_entry(nd, struct symbol, rb_node);
 
-		if (prev->end == prev->start && prev->end != curr->start)
-			arch__symbols__fixup_end(prev, curr);
+		/*
+		 * On some architecture kernel text segment start is located at
+		 * some low memory address, while modules are located at high
+		 * memory addresses (or vice versa).  The gap between end of
+		 * kernel text segment and beginning of first module's text
+		 * segment is very big.  Therefore do not fill this gap and do
+		 * not assign it to the kernel dso map (kallsyms).
+		 *
+		 * In kallsyms, it determines module symbols using '[' character
+		 * like in:
+		 *   ffffffffc1937000 T hdmi_driver_init  [snd_hda_codec_hdmi]
+		 */
+		if (prev->end == prev->start) {
+			/* Last kernel/module symbol mapped to end of page */
+			if (is_kallsyms && (!strchr(prev->name, '[') !=
+					    !strchr(curr->name, '[')))
+				prev->end = roundup(prev->end + 4096, 4096);
+			else
+				prev->end = curr->start;
+
+			pr_debug4("%s sym:%s end:%#" PRIx64 "\n",
+				  __func__, prev->name, prev->end);
+		}
 	}
 
 	/* Last entry */
@@ -1340,10 +1357,23 @@
 
 	/* Find the kernel map using the '_stext' symbol */
 	if (!kallsyms__get_function_start(kallsyms_filename, "_stext", &stext)) {
+		u64 replacement_size = 0;
+
 		list_for_each_entry(new_map, &md.maps, node) {
-			if (stext >= new_map->start && stext < new_map->end) {
+			u64 new_size = new_map->end - new_map->start;
+
+			if (!(stext >= new_map->start && stext < new_map->end))
+				continue;
+
+			/*
+			 * On some architectures, ARM64 for example, the kernel
+			 * text can get allocated inside of the vmalloc segment.
+			 * Select the smallest matching segment, in case stext
+			 * falls within more than one in the list.
+			 */
+			if (!replacement_map || new_size < replacement_size) {
 				replacement_map = new_map;
-				break;
+				replacement_size = new_size;
 			}
 		}
 	}
@@ -1456,7 +1486,7 @@
 	if (kallsyms__delta(kmap, filename, &delta))
 		return -1;
 
-	symbols__fixup_end(&dso->symbols);
+	symbols__fixup_end(&dso->symbols, true);
 	symbols__fixup_duplicate(&dso->symbols);
 
 	if (dso->kernel == DSO_SPACE__KERNEL_GUEST)
@@ -1648,7 +1678,7 @@
 #undef bfd_asymbol_section
 #endif
 
-	symbols__fixup_end(&dso->symbols);
+	symbols__fixup_end(&dso->symbols, false);
 	symbols__fixup_duplicate(&dso->symbols);
 	dso->adjust_symbols = 1;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/symbol.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/symbol.h
@@ -192,7 +192,7 @@
 		       bool kernel);
 void symbols__insert(struct rb_root_cached *symbols, struct symbol *sym);
 void symbols__fixup_duplicate(struct rb_root_cached *symbols);
-void symbols__fixup_end(struct rb_root_cached *symbols);
+void symbols__fixup_end(struct rb_root_cached *symbols, bool is_kallsyms);
 void maps__fixup_end(struct maps *maps);
 
 typedef int (*mapfn_t)(u64 start, u64 len, u64 pgoff, void *data);
@@ -230,7 +230,6 @@
 #define SYMBOL_A 0
 #define SYMBOL_B 1
 
-void arch__symbols__fixup_end(struct symbol *p, struct symbol *c);
 int arch__compare_symbol_names(const char *namea, const char *nameb);
 int arch__compare_symbol_names_n(const char *namea, const char *nameb,
 				 unsigned int n);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/synthetic-events.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/synthetic-events.c
@@ -367,13 +367,24 @@
 					     bool is_kernel)
 {
 	struct build_id bid;
+	struct nsinfo *nsi;
+	struct nscookie nc;
 	int rc;
 
-	if (is_kernel)
+	if (is_kernel) {
 		rc = sysfs__read_build_id("/sys/kernel/notes", &bid);
-	else
-		rc = filename__read_build_id(event->filename, &bid) > 0 ? 0 : -1;
+		goto out;
+	}
+
+	nsi = nsinfo__new(event->pid);
+	nsinfo__mountns_enter(nsi, &nc);
 
+	rc = filename__read_build_id(event->filename, &bid) > 0 ? 0 : -1;
+
+	nsinfo__mountns_exit(&nc);
+	nsinfo__put(nsi);
+
+out:
 	if (rc == 0) {
 		memcpy(event->build_id, bid.data, sizeof(bid.data));
 		event->build_id_size = (u8) bid.size;
@@ -753,7 +764,7 @@
 	snprintf(filename, sizeof(filename), "%s/proc/%d/task",
 		 machine->root_dir, pid);
 
-	n = scandir(filename, &dirent, filter_task, alphasort);
+	n = scandir(filename, &dirent, filter_task, NULL);
 	if (n < 0)
 		return n;
 
@@ -983,7 +994,7 @@
 		return 0;
 
 	snprintf(proc_path, sizeof(proc_path), "%s/proc", machine->root_dir);
-	n = scandir(proc_path, &dirent, filter_task, alphasort);
+	n = scandir(proc_path, &dirent, filter_task, NULL);
 	if (n < 0)
 		return err;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/target.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/target.h
@@ -18,6 +18,7 @@
 	bool	     per_thread;
 	bool	     use_bpf;
 	bool	     hybrid;
+	int	     initial_delay;
 	const char   *attr_map;
 };
 
@@ -72,6 +73,17 @@
 	return !target__has_task(target) && !target__has_cpu(target);
 }
 
+static inline bool target__enable_on_exec(struct target *target)
+{
+	/*
+	 * Normally enable_on_exec should be set if:
+	 *  1) The tracee process is forked (not attaching to existed task or cpu).
+	 *  2) And initial_delay is not configured.
+	 * Otherwise, we enable tracee events manually.
+	 */
+	return target__none(target) && !target->initial_delay;
+}
+
 static inline bool target__has_per_thread(struct target *target)
 {
 	return target->system_wide && target->per_thread;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/thread_map.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/thread_map.c
@@ -279,13 +279,13 @@
 		threads->nr = ntasks;
 	}
 out:
+	strlist__delete(slist);
 	if (threads)
 		refcount_set(&threads->refcnt, 1);
 	return threads;
 
 out_free_threads:
 	zfree(&threads);
-	strlist__delete(slist);
 	goto out;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/time-utils.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/time-utils.c
@@ -20,7 +20,7 @@
 	u64 time_sec, time_nsec;
 	char *end;
 
-	time_sec = strtoul(str, &end, 10);
+	time_sec = strtoull(str, &end, 10);
 	if (*end != '.' && *end != '\0')
 		return -1;
 
@@ -38,7 +38,7 @@
 		for (i = strlen(nsec_buf); i < 9; i++)
 			nsec_buf[i] = '0';
 
-		time_nsec = strtoul(nsec_buf, &end, 10);
+		time_nsec = strtoull(nsec_buf, &end, 10);
 		if (*end != '\0')
 			return -1;
 	} else
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/units.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/units.c
@@ -64,7 +64,7 @@
 
 int unit_number__scnprintf(char *buf, size_t size, u64 n)
 {
-	char unit[4] = "BKMG";
+	char unit[] = "BKMG";
 	int i = 0;
 
 	while (((n / 1024) > 1) && (i < 3)) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/util.c
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/util.c
@@ -379,32 +379,32 @@
 	return 0;
 }
 
-const char *perf_tip(const char *dirpath)
+int perf_tip(char **strp, const char *dirpath)
 {
 	struct strlist *tips;
 	struct str_node *node;
-	char *tip = NULL;
 	struct strlist_config conf = {
 		.dirname = dirpath,
 		.file_only = true,
 	};
+	int ret = 0;
 
+	*strp = NULL;
 	tips = strlist__new("tips.txt", &conf);
 	if (tips == NULL)
-		return errno == ENOENT ? NULL :
-			"Tip: check path of tips.txt or get more memory! ;-p";
+		return -errno;
 
 	if (strlist__nr_entries(tips) == 0)
 		goto out;
 
 	node = strlist__entry(tips, random() % strlist__nr_entries(tips));
-	if (asprintf(&tip, "Tip: %s", node->s) < 0)
-		tip = (char *)"Tip: get more memory! ;-)";
+	if (asprintf(strp, "Tip: %s", node->s) < 0)
+		ret = -ENOMEM;
 
 out:
 	strlist__delete(tips);
 
-	return tip;
+	return ret;
 }
 
 char *perf_exe(char *buf, int len)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/perf/util/util.h
+++ linux-xilinx-zynqmp-5.15.0/tools/perf/util/util.h
@@ -39,7 +39,7 @@
 #define KVER_FMT	"%d.%d.%d"
 #define KVER_PARAM(x)	KVER_VERSION(x), KVER_PATCHLEVEL(x), KVER_SUBLEVEL(x)
 
-const char *perf_tip(const char *dirpath);
+int perf_tip(char **strp, const char *dirpath);
 
 #ifndef HAVE_SCHED_GETCPU_SUPPORT
 int sched_getcpu(void);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/acpi/Makefile.rules
+++ linux-xilinx-zynqmp-5.15.0/tools/power/acpi/Makefile.rules
@@ -9,7 +9,7 @@
 toolobjs := $(addprefix $(objdir),$(TOOL_OBJS))
 $(OUTPUT)$(TOOL): $(toolobjs) FORCE
 	$(ECHO) "  LD      " $(subst $(OUTPUT),,$@)
-	$(QUIET) $(LD) $(CFLAGS) $(LDFLAGS) $(toolobjs) -L$(OUTPUT) -o $@
+	$(QUIET_LINK)$(CC) $(CFLAGS) $(LDFLAGS) $(toolobjs) -L$(OUTPUT) -o $@
 	$(ECHO) "  STRIP   " $(subst $(OUTPUT),,$@)
 	$(QUIET) $(STRIPCMD) $@
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/cpupower/utils/helpers/amd.c
+++ linux-xilinx-zynqmp-5.15.0/tools/power/cpupower/utils/helpers/amd.c
@@ -38,6 +38,16 @@
 		unsigned res1:31;
 		unsigned en:1;
 	} pstatedef;
+	/* since fam 1Ah: */
+	struct {
+		unsigned fid:12;
+		unsigned res1:2;
+		unsigned vid:8;
+		unsigned iddval:8;
+		unsigned idddiv:2;
+		unsigned res2:31;
+		unsigned en:1;
+	} pstatedef2;
 	unsigned long long val;
 };
 
@@ -45,6 +55,10 @@
 {
 	int t;
 
+	/* Fam 1Ah onward do not use did */
+	if (cpupower_cpu_info.family >= 0x1A)
+		return 0;
+
 	if (cpupower_cpu_info.caps & CPUPOWER_CAP_AMD_PSTATEDEF)
 		t = pstate.pstatedef.did;
 	else if (cpupower_cpu_info.family == 0x12)
@@ -58,12 +72,18 @@
 static int get_cof(union core_pstate pstate)
 {
 	int t;
-	int fid, did, cof;
+	int fid, did, cof = 0;
 
 	did = get_did(pstate);
 	if (cpupower_cpu_info.caps & CPUPOWER_CAP_AMD_PSTATEDEF) {
-		fid = pstate.pstatedef.fid;
-		cof = 200 * fid / did;
+		if (cpupower_cpu_info.family >= 0x1A) {
+			fid = pstate.pstatedef2.fid;
+			if (fid > 0x0f)
+				cof = (fid * 5);
+		} else {
+			fid = pstate.pstatedef.fid;
+			cof = 200 * fid / did;
+		}
 	} else {
 		t = 0x10;
 		fid = pstate.pstate.fid;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/cpupower/utils/idle_monitor/mperf_monitor.c
+++ linux-xilinx-zynqmp-5.15.0/tools/power/cpupower/utils/idle_monitor/mperf_monitor.c
@@ -33,7 +33,7 @@
 				   unsigned int cpu);
 static int mperf_get_count_freq(unsigned int id, unsigned long long *count,
 				unsigned int cpu);
-static struct timespec time_start, time_end;
+static struct timespec *time_start, *time_end;
 
 static cstate_t mperf_cstates[MPERF_CSTATE_COUNT] = {
 	{
@@ -70,8 +70,8 @@
  */
 static unsigned long max_frequency;
 
-static unsigned long long tsc_at_measure_start;
-static unsigned long long tsc_at_measure_end;
+static unsigned long long *tsc_at_measure_start;
+static unsigned long long *tsc_at_measure_end;
 static unsigned long long *mperf_previous_count;
 static unsigned long long *aperf_previous_count;
 static unsigned long long *mperf_current_count;
@@ -169,12 +169,12 @@
 	aperf_diff = aperf_current_count[cpu] - aperf_previous_count[cpu];
 
 	if (max_freq_mode == MAX_FREQ_TSC_REF) {
-		tsc_diff = tsc_at_measure_end - tsc_at_measure_start;
+		tsc_diff = tsc_at_measure_end[cpu] - tsc_at_measure_start[cpu];
 		*percent = 100.0 * mperf_diff / tsc_diff;
 		dprint("%s: TSC Ref - mperf_diff: %llu, tsc_diff: %llu\n",
 		       mperf_cstates[id].name, mperf_diff, tsc_diff);
 	} else if (max_freq_mode == MAX_FREQ_SYSFS) {
-		timediff = max_frequency * timespec_diff_us(time_start, time_end);
+		timediff = max_frequency * timespec_diff_us(time_start[cpu], time_end[cpu]);
 		*percent = 100.0 * mperf_diff / timediff;
 		dprint("%s: MAXFREQ - mperf_diff: %llu, time_diff: %llu\n",
 		       mperf_cstates[id].name, mperf_diff, timediff);
@@ -206,8 +206,8 @@
 
 	if (max_freq_mode == MAX_FREQ_TSC_REF) {
 		/* Calculate max_freq from TSC count */
-		tsc_diff = tsc_at_measure_end - tsc_at_measure_start;
-		time_diff = timespec_diff_us(time_start, time_end);
+		tsc_diff = tsc_at_measure_end[cpu] - tsc_at_measure_start[cpu];
+		time_diff = timespec_diff_us(time_start[cpu], time_end[cpu]);
 		max_frequency = tsc_diff / time_diff;
 	}
 
@@ -225,32 +225,25 @@
 static int mperf_start(void)
 {
 	int cpu;
-	unsigned long long dbg;
 
-	clock_gettime(CLOCK_REALTIME, &time_start);
-	mperf_get_tsc(&tsc_at_measure_start);
-
-	for (cpu = 0; cpu < cpu_count; cpu++)
+	for (cpu = 0; cpu < cpu_count; cpu++) {
+		clock_gettime(CLOCK_REALTIME, &time_start[cpu]);
+		mperf_get_tsc(&tsc_at_measure_start[cpu]);
 		mperf_init_stats(cpu);
+	}
 
-	mperf_get_tsc(&dbg);
-	dprint("TSC diff: %llu\n", dbg - tsc_at_measure_start);
 	return 0;
 }
 
 static int mperf_stop(void)
 {
-	unsigned long long dbg;
 	int cpu;
 
-	for (cpu = 0; cpu < cpu_count; cpu++)
+	for (cpu = 0; cpu < cpu_count; cpu++) {
 		mperf_measure_stats(cpu);
-
-	mperf_get_tsc(&tsc_at_measure_end);
-	clock_gettime(CLOCK_REALTIME, &time_end);
-
-	mperf_get_tsc(&dbg);
-	dprint("TSC diff: %llu\n", dbg - tsc_at_measure_end);
+		mperf_get_tsc(&tsc_at_measure_end[cpu]);
+		clock_gettime(CLOCK_REALTIME, &time_end[cpu]);
+	}
 
 	return 0;
 }
@@ -353,7 +346,10 @@
 	aperf_previous_count = calloc(cpu_count, sizeof(unsigned long long));
 	mperf_current_count = calloc(cpu_count, sizeof(unsigned long long));
 	aperf_current_count = calloc(cpu_count, sizeof(unsigned long long));
-
+	tsc_at_measure_start = calloc(cpu_count, sizeof(unsigned long long));
+	tsc_at_measure_end = calloc(cpu_count, sizeof(unsigned long long));
+	time_start = calloc(cpu_count, sizeof(struct timespec));
+	time_end = calloc(cpu_count, sizeof(struct timespec));
 	mperf_monitor.name_len = strlen(mperf_monitor.name);
 	return &mperf_monitor;
 }
@@ -364,6 +360,10 @@
 	free(aperf_previous_count);
 	free(mperf_current_count);
 	free(aperf_current_count);
+	free(tsc_at_measure_start);
+	free(tsc_at_measure_end);
+	free(time_start);
+	free(time_end);
 	free(is_valid);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/x86/intel-speed-select/isst-config.c
+++ linux-xilinx-zynqmp-5.15.0/tools/power/x86/intel-speed-select/isst-config.c
@@ -108,7 +108,7 @@
 
 int is_spr_platform(void)
 {
-	if (cpu_model == 0x8F)
+	if (cpu_model == 0x8F || cpu_model == 0xCF)
 		return 1;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/x86/turbostat/turbostat.8
+++ linux-xilinx-zynqmp-5.15.0/tools/power/x86/turbostat/turbostat.8
@@ -296,6 +296,8 @@
 
 # chmod +r /dev/cpu/*/msr
 
+# chmod +r /dev/cpu_dma_latency
+
 .B "turbostat "
 reads hardware counters, but doesn't write them.
 So it will not interfere with the OS or other programs, including
@@ -320,7 +322,7 @@
 
 Busy% = MPERF_delta/TSC_delta
 
-Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/measurement_interval
+Bzy_MHz = TSC_delta*APERF_delta/MPERF_delta/measurement_interval
 
 Note that these calculations depend on TSC_delta, so they
 are not reliable during intervals when TSC_MHz is not running at the base frequency.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/x86/turbostat/turbostat.c
+++ linux-xilinx-zynqmp-5.15.0/tools/power/x86/turbostat/turbostat.c
@@ -166,6 +166,8 @@
 #define	NAME_BYTES 20
 #define PATH_BYTES 128
 
+#define MAX_NOFILE 0x8000
+
 int backwards_count;
 char *progname;
 
@@ -417,6 +419,7 @@
 	int num_cpus;
 	int num_cores;
 	int max_cpu_num;
+	int max_die_id;
 	int max_node_num;
 	int nodes_per_pkg;
 	int cores_per_node;
@@ -1761,9 +1764,10 @@
 	average.packages.rapl_dram_perf_status += p->rapl_dram_perf_status;
 
 	for (i = 0, mp = sys.pp; mp; i++, mp = mp->next) {
-		if (mp->format == FORMAT_RAW)
-			continue;
-		average.packages.counter[i] += p->counter[i];
+		if ((mp->format == FORMAT_RAW) && (topo.num_packages == 0))
+			average.packages.counter[i] = p->counter[i];
+		else
+			average.packages.counter[i] += p->counter[i];
 	}
 	return 0;
 }
@@ -2100,7 +2104,7 @@
 	if ((DO_BIC(BIC_CPU_c6) || soft_c1_residency_display(BIC_CPU_c6)) && !do_knl_cstates) {
 		if (get_msr(cpu, MSR_CORE_C6_RESIDENCY, &c->c6))
 			return -7;
-	} else if (do_knl_cstates || soft_c1_residency_display(BIC_CPU_c6)) {
+	} else if (do_knl_cstates && soft_c1_residency_display(BIC_CPU_c6)) {
 		if (get_msr(cpu, MSR_KNL_CORE_C6_RESIDENCY, &c->c6))
 			return -7;
 	}
@@ -4241,7 +4245,7 @@
 
 	fprintf(outf, "cpu%d: MSR_HWP_STATUS: 0x%08llx "
 		"(%sGuaranteed_Perf_Change, %sExcursion_Min)\n",
-		cpu, msr, ((msr) & 0x1) ? "" : "No-", ((msr) & 0x2) ? "" : "No-");
+		cpu, msr, ((msr) & 0x1) ? "" : "No-", ((msr) & 0x4) ? "" : "No-");
 
 	return 0;
 }
@@ -4376,6 +4380,7 @@
 	case INTEL_FAM6_BROADWELL_X:	/* BDX */
 	case INTEL_FAM6_SKYLAKE_X:	/* SKX */
 	case INTEL_FAM6_XEON_PHI_KNL:	/* KNL */
+	case INTEL_FAM6_ICELAKE_X:	/* ICX */
 		return (rapl_dram_energy_units = 15.3 / 1000000);
 	default:
 		return (rapl_energy_units);
@@ -5209,6 +5214,10 @@
 	case INTEL_FAM6_LAKEFIELD:
 	case INTEL_FAM6_ALDERLAKE:
 	case INTEL_FAM6_ALDERLAKE_L:
+	case INTEL_FAM6_ALDERLAKE_N:
+	case INTEL_FAM6_RAPTORLAKE:
+	case INTEL_FAM6_RAPTORLAKE_P:
+	case INTEL_FAM6_RAPTORLAKE_S:
 		return INTEL_FAM6_CANNONLAKE_L;
 
 	case INTEL_FAM6_ATOM_TREMONT_L:
@@ -5217,6 +5226,9 @@
 	case INTEL_FAM6_ICELAKE_D:
 	case INTEL_FAM6_SAPPHIRERAPIDS_X:
 		return INTEL_FAM6_ICELAKE_X;
+
+	case INTEL_FAM6_EMERALDRAPIDS_X:
+		return INTEL_FAM6_SAPPHIRERAPIDS_X;
 	}
 	return model;
 }
@@ -5236,7 +5248,7 @@
 
 	retval = read(fd, (void *)&value, sizeof(int));
 	if (retval != sizeof(int)) {
-		warn("read %s\n", path);
+		warn("read failed %s\n", path);
 		close(fd);
 		return;
 	}
@@ -5542,6 +5554,7 @@
 	rapl_probe(family, model);
 	perf_limit_reasons_probe(family, model);
 	automatic_cstate_conversion_probe(family, model);
+	prewake_cstate_probe(family, model);
 
 	check_tcc_offset(model_orig);
 
@@ -5611,7 +5624,6 @@
 	int i;
 	int max_core_id = 0;
 	int max_package_id = 0;
-	int max_die_id = 0;
 	int max_siblings = 0;
 
 	/* Initialize num_cpus, max_cpu_num */
@@ -5680,8 +5692,8 @@
 
 		/* get die information */
 		cpus[i].die_id = get_die_id(i);
-		if (cpus[i].die_id > max_die_id)
-			max_die_id = cpus[i].die_id;
+		if (cpus[i].die_id > topo.max_die_id)
+			topo.max_die_id = cpus[i].die_id;
 
 		/* get numa node information */
 		cpus[i].physical_node_id = get_physical_node_id(&cpus[i]);
@@ -5707,9 +5719,9 @@
 	if (!summary_only && topo.cores_per_node > 1)
 		BIC_PRESENT(BIC_Core);
 
-	topo.num_die = max_die_id + 1;
+	topo.num_die = topo.max_die_id + 1;
 	if (debug > 1)
-		fprintf(outf, "max_die_id %d, sizing for %d die\n", max_die_id, topo.num_die);
+		fprintf(outf, "max_die_id %d, sizing for %d die\n", topo.max_die_id, topo.num_die);
 	if (!summary_only && topo.num_die > 1)
 		BIC_PRESENT(BIC_Die);
 
@@ -6420,6 +6432,22 @@
 	}
 }
 
+void set_rlimit(void)
+{
+	struct rlimit limit;
+
+	if (getrlimit(RLIMIT_NOFILE, &limit) < 0)
+		err(1, "Failed to get rlimit");
+
+	if (limit.rlim_max < MAX_NOFILE)
+		limit.rlim_max = MAX_NOFILE;
+	if (limit.rlim_cur < MAX_NOFILE)
+		limit.rlim_cur = MAX_NOFILE;
+
+	if (setrlimit(RLIMIT_NOFILE, &limit) < 0)
+		err(1, "Failed to set rlimit");
+}
+
 int main(int argc, char **argv)
 {
 	outf = stderr;
@@ -6430,6 +6458,9 @@
 
 	probe_sysfs();
 
+	if (!getuid())
+		set_rlimit();
+
 	turbostat_init();
 
 	/* dump counters and exit */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/power/x86/x86_energy_perf_policy/x86_energy_perf_policy.c
+++ linux-xilinx-zynqmp-5.15.0/tools/power/x86/x86_energy_perf_policy/x86_energy_perf_policy.c
@@ -1241,6 +1241,7 @@
 	retval = fscanf(fp, "%d\n", &pkg);
 	if (retval != 1)
 		errx(1, "%s: failed to parse", pathname);
+	fclose(fp);
 	return pkg;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/scripts/Makefile.arch
+++ linux-xilinx-zynqmp-5.15.0/tools/scripts/Makefile.arch
@@ -6,8 +6,8 @@
                                   -e s/ppc.*/powerpc/ -e s/mips.*/mips/ \
                                   -e s/sh[234].*/sh/ -e s/aarch64.*/arm64/ )
 
-ifndef ARCH
-ARCH := $(HOSTARCH)
+ifeq ($(strip $(ARCH)),)
+override ARCH := $(HOSTARCH)
 endif
 
 SRCARCH := $(ARCH)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/ktest/ktest.pl
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/ktest/ktest.pl
@@ -178,6 +178,7 @@
 my $store_successes;
 my $test_name;
 my $timeout;
+my $run_timeout;
 my $connect_timeout;
 my $config_bisect_exec;
 my $booted_timeout;
@@ -340,6 +341,7 @@
     "STORE_SUCCESSES"		=> \$store_successes,
     "TEST_NAME"			=> \$test_name,
     "TIMEOUT"			=> \$timeout,
+    "RUN_TIMEOUT"		=> \$run_timeout,
     "CONNECT_TIMEOUT"		=> \$connect_timeout,
     "CONFIG_BISECT_EXEC"	=> \$config_bisect_exec,
     "BOOTED_TIMEOUT"		=> \$booted_timeout,
@@ -834,6 +836,7 @@
     if ($lvalue =~ /^(TEST|BISECT|CONFIG_BISECT)_TYPE(\[.*\])?$/ &&
 	$prvalue !~ /^(config_|)bisect$/ &&
 	$prvalue !~ /^build$/ &&
+	$prvalue !~ /^make_warnings_file$/ &&
 	$buildonly) {
 
 	# Note if a test is something other than build, then we
@@ -1488,7 +1491,8 @@
 
 	# Still need to wait for the reboot to finish
 	wait_for_monitor($time, $reboot_success_line);
-
+    }
+    if ($powercycle || $time) {
 	end_monitor;
     }
 }
@@ -1850,6 +1854,14 @@
     $command =~ s/\$SSH_USER/$ssh_user/g;
     $command =~ s/\$MACHINE/$machine/g;
 
+    if (!defined($timeout)) {
+	$timeout = $run_timeout;
+    }
+
+    if (!defined($timeout)) {
+	$timeout = -1; # tell wait_for_input to wait indefinitely
+    }
+
     doprint("$command ... ");
     $start_time = time;
 
@@ -1876,13 +1888,10 @@
 
     while (1) {
 	my $fp = \*CMD;
-	if (defined($timeout)) {
-	    doprint "timeout = $timeout\n";
-	}
 	my $line = wait_for_input($fp, $timeout);
 	if (!defined($line)) {
 	    my $now = time;
-	    if (defined($timeout) && (($now - $start_time) >= $timeout)) {
+	    if ($timeout >= 0 && (($now - $start_time) >= $timeout)) {
 		doprint "Hit timeout of $timeout, killing process\n";
 		$hit_timeout = 1;
 		kill 9, $pid;
@@ -1963,7 +1972,7 @@
 
 sub _get_grub_index {
 
-    my ($command, $target, $skip) = @_;
+    my ($command, $target, $skip, $submenu) = @_;
 
     return if (defined($grub_number) && defined($last_grub_menu) &&
 	$last_grub_menu eq $grub_menu && defined($last_machine) &&
@@ -1980,11 +1989,16 @@
 
     my $found = 0;
 
+    my $submenu_number = 0;
+
     while (<IN>) {
 	if (/$target/) {
 	    $grub_number++;
 	    $found = 1;
 	    last;
+	} elsif (defined($submenu) && /$submenu/) {
+		$submenu_number++;
+		$grub_number = -1;
 	} elsif (/$skip/) {
 	    $grub_number++;
 	}
@@ -1993,6 +2007,9 @@
 
     dodie "Could not find '$grub_menu' through $command on $machine"
 	if (!$found);
+    if ($submenu_number > 0) {
+	$grub_number = "$submenu_number>$grub_number";
+    }
     doprint "$grub_number\n";
     $last_grub_menu = $grub_menu;
     $last_machine = $machine;
@@ -2003,6 +2020,7 @@
     my $command;
     my $target;
     my $skip;
+    my $submenu;
     my $grub_menu_qt;
 
     if ($reboot_type !~ /^grub/) {
@@ -2017,8 +2035,9 @@
 	$skip = '^\s*title\s';
     } elsif ($reboot_type eq "grub2") {
 	$command = "cat $grub_file";
-	$target = '^menuentry.*' . $grub_menu_qt;
-	$skip = '^menuentry\s|^submenu\s';
+	$target = '^\s*menuentry.*' . $grub_menu_qt;
+	$skip = '^\s*menuentry\s';
+	$submenu = '^\s*submenu\s';
     } elsif ($reboot_type eq "grub2bls") {
 	$command = $grub_bls_get;
 	$target = '^title=.*' . $grub_menu_qt;
@@ -2027,7 +2046,7 @@
 	return;
     }
 
-    _get_grub_index($command, $target, $skip);
+    _get_grub_index($command, $target, $skip, $submenu);
 }
 
 sub wait_for_input {
@@ -2044,6 +2063,11 @@
 	$time = $timeout;
     }
 
+    if ($time < 0) {
+	# Negative number means wait indefinitely
+	undef $time;
+    }
+
     $rin = '';
     vec($rin, fileno($fp), 1) = 1;
     vec($rin, fileno(\*STDIN), 1) = 1;
@@ -2090,7 +2114,7 @@
     if ($reboot_type eq "grub") {
 	run_ssh "'(echo \"savedefault --default=$grub_number --once\" | grub --batch)'";
     } elsif (($reboot_type eq "grub2") or ($reboot_type eq "grub2bls")) {
-	run_ssh "$grub_reboot $grub_number";
+	run_ssh "$grub_reboot \"'$grub_number'\"";
     } elsif ($reboot_type eq "syslinux") {
 	run_ssh "$syslinux --once \\\"$syslinux_label\\\" $syslinux_path";
     } elsif (defined $reboot_script) {
@@ -2375,6 +2399,11 @@
     return if ($have_version);
     doprint "$make kernelrelease ... ";
     $version = `$make -s kernelrelease | tail -1`;
+    if (!length($version)) {
+	run_command "$make allnoconfig" or return 0;
+	doprint "$make kernelrelease ... ";
+	$version = `$make -s kernelrelease | tail -1`;
+    }
     chomp($version);
     doprint "$version\n";
     $have_version = 1;
@@ -2915,8 +2944,6 @@
 
     my $failed = 0;
     my $result;
-    my $output;
-    my $ret;
 
     $in_bisect = 1;
 
@@ -3768,9 +3795,10 @@
     # .config to make sure it is missing the config that
     # we had before
     my %configs = %min_configs;
-    delete $configs{$config};
+    $configs{$config} = "# $config is not set";
     make_new_config ((values %configs), (values %keep_configs));
     make_oldconfig;
+    delete $configs{$config};
     undef %configs;
     assign_configs \%configs, $output_config;
 
@@ -4182,6 +4210,9 @@
 }
 
 sub cancel_test {
+    if ($monitor_cnt) {
+	end_monitor;
+    }
     if ($email_when_canceled) {
 	my $name = get_test_name;
 	send_email("KTEST: Your [$name] test was cancelled",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/ktest/sample.conf
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/ktest/sample.conf
@@ -809,6 +809,11 @@
 # is issued instead of a reboot.
 # CONNECT_TIMEOUT = 25
 
+# The timeout in seconds for how long to wait for any running command
+# to timeout. If not defined, it will let it go indefinitely.
+# (default undefined)
+#RUN_TIMEOUT = 600
+
 # In between tests, a reboot of the box may occur, and this
 # is the time to wait for the console after it stops producing
 # output. Some machines may not produce a large lag on reboot
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/kunit/kunit_kernel.py
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/kunit/kunit_kernel.py
@@ -6,6 +6,7 @@
 # Author: Felix Guo <felixguoxiuping@gmail.com>
 # Author: Brendan Higgins <brendanhiggins@google.com>
 
+import importlib.abc
 import importlib.util
 import logging
 import subprocess
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/nvdimm/test/iomap.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/nvdimm/test/iomap.c
@@ -100,25 +100,17 @@
 {
 	struct dev_pagemap *pgmap = _pgmap;
 
-	WARN_ON(!pgmap || !pgmap->ref);
+	WARN_ON(!pgmap);
 
-	if (pgmap->ops && pgmap->ops->kill)
-		pgmap->ops->kill(pgmap);
-	else
-		percpu_ref_kill(pgmap->ref);
-
-	if (pgmap->ops && pgmap->ops->cleanup) {
-		pgmap->ops->cleanup(pgmap);
-	} else {
-		wait_for_completion(&pgmap->done);
-		percpu_ref_exit(pgmap->ref);
-	}
+	percpu_ref_kill(&pgmap->ref);
+
+	wait_for_completion(&pgmap->done);
+	percpu_ref_exit(&pgmap->ref);
 }
 
 static void dev_pagemap_percpu_release(struct percpu_ref *ref)
 {
-	struct dev_pagemap *pgmap =
-		container_of(ref, struct dev_pagemap, internal_ref);
+	struct dev_pagemap *pgmap = container_of(ref, struct dev_pagemap, ref);
 
 	complete(&pgmap->done);
 }
@@ -132,22 +124,11 @@
 	if (!nfit_res)
 		return devm_memremap_pages(dev, pgmap);
 
-	if (!pgmap->ref) {
-		if (pgmap->ops && (pgmap->ops->kill || pgmap->ops->cleanup))
-			return ERR_PTR(-EINVAL);
-
-		init_completion(&pgmap->done);
-		error = percpu_ref_init(&pgmap->internal_ref,
-				dev_pagemap_percpu_release, 0, GFP_KERNEL);
-		if (error)
-			return ERR_PTR(error);
-		pgmap->ref = &pgmap->internal_ref;
-	} else {
-		if (!pgmap->ops || !pgmap->ops->kill || !pgmap->ops->cleanup) {
-			WARN(1, "Missing reference count teardown definition\n");
-			return ERR_PTR(-EINVAL);
-		}
-	}
+	init_completion(&pgmap->done);
+	error = percpu_ref_init(&pgmap->ref, dev_pagemap_percpu_release, 0,
+				GFP_KERNEL);
+	if (error)
+		return ERR_PTR(error);
 
 	error = devm_add_action_or_reset(dev, nfit_test_kill, pgmap);
 	if (error)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/radix-tree/regression1.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/radix-tree/regression1.c
@@ -177,7 +177,7 @@
 	nr_threads = 2;
 	pthread_barrier_init(&worker_barrier, NULL, nr_threads);
 
-	threads = malloc(nr_threads * sizeof(pthread_t *));
+	threads = malloc(nr_threads * sizeof(*threads));
 
 	for (i = 0; i < nr_threads; i++) {
 		arg = i;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/Makefile
@@ -8,6 +8,7 @@
 TARGETS += core
 TARGETS += cpufreq
 TARGETS += cpu-hotplug
+TARGETS += damon
 TARGETS += drivers/dma-buf
 TARGETS += efivarfs
 TARGETS += exec
@@ -51,6 +52,7 @@
 TARGETS += pstore
 TARGETS += ptrace
 TARGETS += openat2
+TARGETS += resctrl
 TARGETS += rlimits
 TARGETS += rseq
 TARGETS += rtc
@@ -113,19 +115,27 @@
 override LDFLAGS =
 endif
 
-ifneq ($(O),)
-	BUILD := $(O)/kselftest
+top_srcdir ?= ../../..
+
+ifeq ("$(origin O)", "command line")
+  KBUILD_OUTPUT := $(O)
+endif
+
+ifneq ($(KBUILD_OUTPUT),)
+  # Make's built-in functions such as $(abspath ...), $(realpath ...) cannot
+  # expand a shell special character '~'. We use a somewhat tedious way here.
+  abs_objtree := $(shell cd $(top_srcdir) && mkdir -p $(KBUILD_OUTPUT) && cd $(KBUILD_OUTPUT) && pwd)
+  $(if $(abs_objtree),, \
+    $(error failed to create output directory "$(KBUILD_OUTPUT)"))
+  # $(realpath ...) resolves symlinks
+  abs_objtree := $(realpath $(abs_objtree))
+  BUILD := $(abs_objtree)/kselftest
 else
-	ifneq ($(KBUILD_OUTPUT),)
-		BUILD := $(KBUILD_OUTPUT)/kselftest
-	else
-		BUILD := $(shell pwd)
-		DEFAULT_INSTALL_HDR_PATH := 1
-	endif
+  BUILD := $(CURDIR)
+  DEFAULT_INSTALL_HDR_PATH := 1
 endif
 
 # Prepare for headers install
-top_srcdir ?= ../../..
 include $(top_srcdir)/scripts/subarch.include
 ARCH           ?= $(SUBARCH)
 export KSFT_KHDR_INSTALL_DONE := 1
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/arm64/bti/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/arm64/bti/Makefile
@@ -39,7 +39,7 @@
 	teststubs-bti.o                         \
 	trampoline-bti.o
 gen/btitest: $(BTI_OBJS)
-	$(CC) $(CFLAGS_BTI) $(CFLAGS_COMMON) -nostdlib -o $@ $^
+	$(CC) $(CFLAGS_BTI) $(CFLAGS_COMMON) -nostdlib -static -o $@ $^
 
 NOBTI_OBJS =                                    \
 	test-nobti.o                         \
@@ -50,7 +50,7 @@
 	teststubs-nobti.o                       \
 	trampoline-nobti.o
 gen/nobtitest: $(NOBTI_OBJS)
-	$(CC) $(CFLAGS_BTI) $(CFLAGS_COMMON) -nostdlib -o $@ $^
+	$(CC) $(CFLAGS_BTI) $(CFLAGS_COMMON) -nostdlib -static -o $@ $^
 
 # Including KSFT lib.mk here will also mangle the TEST_GEN_PROGS list
 # to account for any OUTPUT target-dirs optionally provided by
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/arm64/mte/check_tags_inclusion.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/arm64/mte/check_tags_inclusion.c
@@ -57,7 +57,7 @@
 			ptr = (char *)mte_insert_tags(ptr, BUFFER_SIZE);
 			/* Check tag value */
 			if (MT_FETCH_TAG((uintptr_t)ptr) == tag) {
-				ksft_print_msg("FAIL: wrong tag = 0x%x with include mask=0x%x\n",
+				ksft_print_msg("FAIL: wrong tag = 0x%lx with include mask=0x%x\n",
 					       MT_FETCH_TAG((uintptr_t)ptr),
 					       MT_INCLUDE_VALID_TAG(tag));
 				result = KSFT_FAIL;
@@ -89,7 +89,7 @@
 			ptr = (char *)mte_insert_tags(ptr, BUFFER_SIZE);
 			/* Check tag value */
 			if (MT_FETCH_TAG((uintptr_t)ptr) < tag) {
-				ksft_print_msg("FAIL: wrong tag = 0x%x with include mask=0x%x\n",
+				ksft_print_msg("FAIL: wrong tag = 0x%lx with include mask=0x%lx\n",
 					       MT_FETCH_TAG((uintptr_t)ptr),
 					       MT_INCLUDE_VALID_TAGS(excl_mask));
 				result = KSFT_FAIL;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/arm64/pauth/pac.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/arm64/pauth/pac.c
@@ -182,6 +182,9 @@
 		return -1;
 	}
 
+	close(new_stdin[1]);
+	close(new_stdout[0]);
+
 	return 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/arm64/signal/testcases/testcases.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/arm64/signal/testcases/testcases.c
@@ -33,7 +33,7 @@
 		return false;
 
 	fprintf(stderr, "Validating EXTRA...\n");
-	term = GET_RESV_NEXT_HEAD(extra);
+	term = GET_RESV_NEXT_HEAD(&extra->head);
 	if (!term || term->magic || term->size) {
 		*err = "Missing terminator after EXTRA context";
 		return false;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/arm64/tags/tags_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/arm64/tags/tags_test.c
@@ -6,6 +6,7 @@
 #include <stdint.h>
 #include <sys/prctl.h>
 #include <sys/utsname.h>
+#include "../../kselftest.h"
 
 #define SHIFT_TAG(tag)		((uint64_t)(tag) << 56)
 #define SET_TAG(ptr, tag)	(((uint64_t)(ptr) & ~SHIFT_TAG(0xff)) | \
@@ -21,6 +22,9 @@
 	if (prctl(PR_SET_TAGGED_ADDR_CTRL, PR_TAGGED_ADDR_ENABLE, 0, 0, 0) == 0)
 		tbi_enabled = 1;
 	ptr = (struct utsname *)malloc(sizeof(*ptr));
+	if (!ptr)
+		ksft_exit_fail_msg("Failed to allocate utsname buffer\n");
+
 	if (tbi_enabled)
 		tag = 0x42;
 	ptr = (struct utsname *)SET_TAG(ptr, tag);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/Makefile
@@ -78,7 +78,7 @@
 	test_xsk.sh
 
 TEST_PROGS_EXTENDED := with_addr.sh \
-	with_tunnels.sh \
+	with_tunnels.sh ima_setup.sh \
 	test_xdp_vlan.sh test_bpftool.py
 
 # Compile but not part of 'make run_tests'
@@ -144,8 +144,6 @@
 # NOTE: Semicolon at the end is critical to override lib.mk's default static
 # rule for binaries.
 $(notdir $(TEST_GEN_PROGS)						\
-	 $(TEST_PROGS)							\
-	 $(TEST_PROGS_EXTENDED)						\
 	 $(TEST_GEN_PROGS_EXTENDED)					\
 	 $(TEST_CUSTOM_PROGS)): %: $(OUTPUT)/% ;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/bench.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/bench.c
@@ -11,6 +11,7 @@
 #include <sys/resource.h>
 #include <signal.h>
 #include "bench.h"
+#include "bpf_util.h"
 #include "testing_helpers.h"
 
 struct env env = {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/benchs/run_bench_rename.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/benchs/run_bench_rename.sh
@@ -2,7 +2,7 @@
 
 set -eufo pipefail
 
-for i in base kprobe kretprobe rawtp fentry fexit fmodret
+for i in base kprobe kretprobe rawtp fentry fexit
 do
 	summary=$(sudo ./bench -w2 -d5 -a rename-$i | tail -n1 | cut -d'(' -f1 | cut -d' ' -f3-)
 	printf "%-10s: %s\n" $i "$summary"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/btf_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/btf_helpers.c
@@ -246,18 +246,23 @@
 	d = btf_dump__new(btf, NULL, &opts, btf_dump_printf);
 	if (libbpf_get_error(d)) {
 		fprintf(stderr, "Failed to create btf_dump instance: %ld\n", libbpf_get_error(d));
-		return NULL;
+		goto err_out;
 	}
 
 	for (i = 1; i <= btf__get_nr_types(btf); i++) {
 		err = btf_dump__dump_type(d, i);
 		if (err) {
 			fprintf(stderr, "Failed to dump type [%d]: %d\n", i, err);
-			return NULL;
+			goto err_out;
 		}
 	}
 
+	btf_dump__free(d);
 	fflush(buf_file);
 	fclose(buf_file);
 	return buf;
+err_out:
+	btf_dump__free(d);
+	fclose(buf_file);
+	return NULL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/cgroup_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/cgroup_helpers.c
@@ -348,10 +348,20 @@
 		return 1;
 	}
 
-	if (mount("net_cls", NETCLS_MOUNT_PATH, "cgroup", 0, "net_cls") &&
-	    errno != EBUSY) {
-		log_err("mount cgroup net_cls");
-		return 1;
+	if (mount("net_cls", NETCLS_MOUNT_PATH, "cgroup", 0, "net_cls")) {
+		if (errno != EBUSY) {
+			log_err("mount cgroup net_cls");
+			return 1;
+		}
+
+		if (rmdir(NETCLS_MOUNT_PATH)) {
+			log_err("rmdir cgroup net_cls");
+			return 1;
+		}
+		if (umount(CGROUP_MOUNT_DFLT)) {
+			log_err("umount cgroup base");
+			return 1;
+		}
 	}
 
 	cleanup_classid_environment();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/map_tests/sk_storage_map.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/map_tests/sk_storage_map.c
@@ -416,7 +416,7 @@
 		rlim_new.rlim_max = rlim_new.rlim_cur + 128;
 		err = setrlimit(RLIMIT_NOFILE, &rlim_new);
 		CHECK(err, "setrlimit(RLIMIT_NOFILE)", "rlim_new:%lu errno:%d",
-		      rlim_new.rlim_cur, errno);
+		      (unsigned long) rlim_new.rlim_cur, errno);
 	}
 
 	err = do_sk_storage_map_stress_free();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/network_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/network_helpers.c
@@ -84,7 +84,7 @@
 	if (reuseport &&
 	    setsockopt(fd, SOL_SOCKET, SO_REUSEPORT, &on, sizeof(on))) {
 		log_err("Failed to set SO_REUSEPORT");
-		return -1;
+		goto error_close;
 	}
 
 	if (bind(fd, addr, addrlen) < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/align.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/align.c
@@ -2,7 +2,7 @@
 #include <test_progs.h>
 
 #define MAX_INSNS	512
-#define MAX_MATCHES	16
+#define MAX_MATCHES	24
 
 struct bpf_reg_match {
 	unsigned int line;
@@ -267,6 +267,7 @@
 			 */
 			BPF_MOV64_REG(BPF_REG_5, BPF_REG_2),
 			BPF_ALU64_REG(BPF_ADD, BPF_REG_5, BPF_REG_6),
+			BPF_MOV64_REG(BPF_REG_4, BPF_REG_5),
 			BPF_ALU64_IMM(BPF_ADD, BPF_REG_5, 14),
 			BPF_MOV64_REG(BPF_REG_4, BPF_REG_5),
 			BPF_ALU64_IMM(BPF_ADD, BPF_REG_4, 4),
@@ -280,6 +281,7 @@
 			BPF_MOV64_REG(BPF_REG_5, BPF_REG_2),
 			BPF_ALU64_IMM(BPF_ADD, BPF_REG_5, 14),
 			BPF_ALU64_REG(BPF_ADD, BPF_REG_5, BPF_REG_6),
+			BPF_MOV64_REG(BPF_REG_4, BPF_REG_5),
 			BPF_ALU64_IMM(BPF_ADD, BPF_REG_5, 4),
 			BPF_ALU64_REG(BPF_ADD, BPF_REG_5, BPF_REG_6),
 			BPF_MOV64_REG(BPF_REG_4, BPF_REG_5),
@@ -311,44 +313,52 @@
 			{15, "R4=pkt(id=1,off=18,r=18,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			{15, "R5=pkt(id=1,off=14,r=18,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			/* Variable offset is added to R5 packet pointer,
-			 * resulting in auxiliary alignment of 4.
+			 * resulting in auxiliary alignment of 4. To avoid BPF
+			 * verifier's precision backtracking logging
+			 * interfering we also have a no-op R4 = R5
+			 * instruction to validate R5 state. We also check
+			 * that R4 is what it should be in such case.
 			 */
-			{18, "R5_w=pkt(id=2,off=0,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{19, "R4_w=pkt(id=2,off=0,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{19, "R5_w=pkt(id=2,off=0,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			/* Constant offset is added to R5, resulting in
 			 * reg->off of 14.
 			 */
-			{19, "R5_w=pkt(id=2,off=14,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{20, "R5_w=pkt(id=2,off=14,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			/* At the time the word size load is performed from R5,
 			 * its total fixed offset is NET_IP_ALIGN + reg->off
 			 * (14) which is 16.  Then the variable offset is 4-byte
 			 * aligned, so the total offset is 4-byte aligned and
 			 * meets the load's requirements.
 			 */
-			{23, "R4=pkt(id=2,off=18,r=18,umax_value=1020,var_off=(0x0; 0x3fc))"},
-			{23, "R5=pkt(id=2,off=14,r=18,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{24, "R4=pkt(id=2,off=18,r=18,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{24, "R5=pkt(id=2,off=14,r=18,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			/* Constant offset is added to R5 packet pointer,
 			 * resulting in reg->off value of 14.
 			 */
-			{26, "R5_w=pkt(id=0,off=14,r=8"},
+			{27, "R5_w=pkt(id=0,off=14,r=8"},
 			/* Variable offset is added to R5, resulting in a
-			 * variable offset of (4n).
+			 * variable offset of (4n). See comment for insn #19
+			 * for R4 = R5 trick.
 			 */
-			{27, "R5_w=pkt(id=3,off=14,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{29, "R4_w=pkt(id=3,off=14,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{29, "R5_w=pkt(id=3,off=14,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			/* Constant is added to R5 again, setting reg->off to 18. */
-			{28, "R5_w=pkt(id=3,off=18,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
+			{30, "R5_w=pkt(id=3,off=18,r=0,umax_value=1020,var_off=(0x0; 0x3fc))"},
 			/* And once more we add a variable; resulting var_off
 			 * is still (4n), fixed offset is not changed.
 			 * Also, we create a new reg->id.
 			 */
-			{29, "R5_w=pkt(id=4,off=18,r=0,umax_value=2040,var_off=(0x0; 0x7fc)"},
+			{32, "R4_w=pkt(id=4,off=18,r=0,umax_value=2040,var_off=(0x0; 0x7fc)"},
+			{32, "R5_w=pkt(id=4,off=18,r=0,umax_value=2040,var_off=(0x0; 0x7fc)"},
 			/* At the time the word size load is performed from R5,
 			 * its total fixed offset is NET_IP_ALIGN + reg->off (18)
 			 * which is 20.  Then the variable offset is (4n), so
 			 * the total offset is 4-byte aligned and meets the
 			 * load's requirements.
 			 */
-			{33, "R4=pkt(id=4,off=22,r=22,umax_value=2040,var_off=(0x0; 0x7fc)"},
-			{33, "R5=pkt(id=4,off=18,r=22,umax_value=2040,var_off=(0x0; 0x7fc)"},
+			{35, "R4=pkt(id=4,off=22,r=22,umax_value=2040,var_off=(0x0; 0x7fc)"},
+			{35, "R5=pkt(id=4,off=18,r=22,umax_value=2040,var_off=(0x0; 0x7fc)"},
 		},
 	},
 	{
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/bind_perm.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/bind_perm.c
@@ -1,13 +1,24 @@
 // SPDX-License-Identifier: GPL-2.0
-#include <test_progs.h>
-#include "bind_perm.skel.h"
-
+#define _GNU_SOURCE
+#include <sched.h>
+#include <stdlib.h>
 #include <sys/types.h>
 #include <sys/socket.h>
 #include <sys/capability.h>
 
+#include "test_progs.h"
+#include "bind_perm.skel.h"
+
 static int duration;
 
+static int create_netns(void)
+{
+	if (!ASSERT_OK(unshare(CLONE_NEWNET), "create netns"))
+		return -1;
+
+	return 0;
+}
+
 void try_bind(int family, int port, int expected_errno)
 {
 	struct sockaddr_storage addr = {};
@@ -75,6 +86,9 @@
 	struct bind_perm *skel;
 	int cgroup_fd;
 
+	if (create_netns())
+		return;
+
 	cgroup_fd = test__join_cgroup("/bind_perm");
 	if (CHECK(cgroup_fd < 0, "cg-join", "errno %d", errno))
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/bpf_iter.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/bpf_iter.c
@@ -150,6 +150,8 @@
 	do_dummy_read(skel->progs.dump_task_stack);
 	do_dummy_read(skel->progs.get_task_user_stacks);
 
+	ASSERT_EQ(skel->bss->num_user_stacks, 1, "num_user_stacks");
+
 	bpf_iter_task_stack__destroy(skel);
 }
 
@@ -1208,13 +1210,14 @@
 		goto out;
 
 	/* Read CMP_BUFFER_SIZE (1kB) from bpf_iter. Read in small chunks
-	 * to trigger seq_file corner cases. The expected output is much
-	 * longer than 1kB, so the while loop will terminate.
+	 * to trigger seq_file corner cases.
 	 */
 	len = 0;
 	while (len < CMP_BUFFER_SIZE) {
 		err = read_fd_into_buffer(iter_fd, task_vma_output + len,
 					  min(read_size, CMP_BUFFER_SIZE - len));
+		if (!err)
+			break;
 		if (CHECK(err < 0, "read_iter_fd", "read_iter_fd failed\n"))
 			goto out;
 		len += err;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/bpf_iter_setsockopt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/bpf_iter_setsockopt.c
@@ -95,7 +95,7 @@
 	struct sockaddr_in6 addr;
 	socklen_t addrlen = sizeof(addr);
 
-	if (!getsockname(fd, &addr, &addrlen))
+	if (!getsockname(fd, (struct sockaddr *)&addr, &addrlen))
 		return ntohs(addr.sin6_port);
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/btf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/btf.c
@@ -882,6 +882,34 @@
 	.btf_load_err = true,
 	.err_str = "Invalid elem",
 },
+{
+	.descr = "var after datasec, ptr followed by modifier",
+	.raw_types = {
+		/* .bss section */				/* [1] */
+		BTF_TYPE_ENC(NAME_TBD, BTF_INFO_ENC(BTF_KIND_DATASEC, 0, 2),
+			sizeof(void*)+4),
+		BTF_VAR_SECINFO_ENC(4, 0, sizeof(void*)),
+		BTF_VAR_SECINFO_ENC(6, sizeof(void*), 4),
+		/* int */					/* [2] */
+		BTF_TYPE_INT_ENC(0, BTF_INT_SIGNED, 0, 32, 4),
+		/* int* */					/* [3] */
+		BTF_TYPE_ENC(0, BTF_INFO_ENC(BTF_KIND_PTR, 0, 0), 2),
+		BTF_VAR_ENC(NAME_TBD, 3, 0),			/* [4] */
+		/* const int */					/* [5] */
+		BTF_TYPE_ENC(0, BTF_INFO_ENC(BTF_KIND_CONST, 0, 0), 2),
+		BTF_VAR_ENC(NAME_TBD, 5, 0),			/* [6] */
+		BTF_END_RAW,
+	},
+	.str_sec = "\0a\0b\0c\0",
+	.str_sec_size = sizeof("\0a\0b\0c\0"),
+	.map_type = BPF_MAP_TYPE_ARRAY,
+	.map_name = ".bss",
+	.key_size = sizeof(int),
+	.value_size = sizeof(void*)+4,
+	.key_type_id = 0,
+	.value_type_id = 1,
+	.max_entries = 1,
+},
 /* Test member exceeds the size of struct.
  *
  * struct A {
@@ -4738,6 +4766,7 @@
 #endif
 
 	assert(0);
+	return 0;
 }
 
 static void set_pprint_mapv(enum pprint_mapv_kind_t mapv_kind,
@@ -4913,7 +4942,7 @@
 	ret = snprintf(pin_path, sizeof(pin_path), "%s/%s",
 		       "/sys/fs/bpf", test->map_name);
 
-	if (CHECK(ret == sizeof(pin_path), "pin_path %s/%s is too long",
+	if (CHECK(ret >= sizeof(pin_path), "pin_path %s/%s is too long",
 		  "/sys/fs/bpf", test->map_name)) {
 		err = -1;
 		goto done;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/btf_map_in_map.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/btf_map_in_map.c
@@ -25,7 +25,7 @@
 	int map1_fd, map2_fd, map3_fd, map4_fd, map5_fd, map1_id, map2_id;
 	int outer_arr_fd, outer_hash_fd, outer_arr_dyn_fd;
 	struct test_btf_map_in_map *skel;
-	int err, key = 0, val, i, fd;
+	int err, key = 0, val, i;
 
 	skel = test_btf_map_in_map__open_and_load();
 	if (CHECK(!skel, "skel_open", "failed to open&load skeleton\n"))
@@ -102,30 +102,6 @@
 	CHECK(map1_id == 0, "map1_id", "failed to get ID 1\n");
 	CHECK(map2_id == 0, "map2_id", "failed to get ID 2\n");
 
-	test_btf_map_in_map__destroy(skel);
-	skel = NULL;
-
-	/* we need to either wait for or force synchronize_rcu(), before
-	 * checking for "still exists" condition, otherwise map could still be
-	 * resolvable by ID, causing false positives.
-	 *
-	 * Older kernels (5.8 and earlier) freed map only after two
-	 * synchronize_rcu()s, so trigger two, to be entirely sure.
-	 */
-	CHECK(kern_sync_rcu(), "sync_rcu", "failed\n");
-	CHECK(kern_sync_rcu(), "sync_rcu", "failed\n");
-
-	fd = bpf_map_get_fd_by_id(map1_id);
-	if (CHECK(fd >= 0, "map1_leak", "inner_map1 leaked!\n")) {
-		close(fd);
-		goto cleanup;
-	}
-	fd = bpf_map_get_fd_by_id(map2_id);
-	if (CHECK(fd >= 0, "map2_leak", "inner_map2 leaked!\n")) {
-		close(fd);
-		goto cleanup;
-	}
-
 cleanup:
 	test_btf_map_in_map__destroy(skel);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/btf_skc_cls_ingress.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/btf_skc_cls_ingress.c
@@ -90,7 +90,7 @@
 
 static void test_conn(void)
 {
-	int listen_fd = -1, cli_fd = -1, err;
+	int listen_fd = -1, cli_fd = -1, srv_fd = -1, err;
 	socklen_t addrlen = sizeof(srv_sa6);
 	int srv_port;
 
@@ -112,6 +112,10 @@
 	if (CHECK_FAIL(cli_fd == -1))
 		goto done;
 
+	srv_fd = accept(listen_fd, NULL, NULL);
+	if (CHECK_FAIL(srv_fd == -1))
+		goto done;
+
 	if (CHECK(skel->bss->listen_tp_sport != srv_port ||
 		  skel->bss->req_sk_sport != srv_port,
 		  "Unexpected sk src port",
@@ -134,11 +138,13 @@
 		close(listen_fd);
 	if (cli_fd != -1)
 		close(cli_fd);
+	if (srv_fd != -1)
+		close(srv_fd);
 }
 
 static void test_syncookie(void)
 {
-	int listen_fd = -1, cli_fd = -1, err;
+	int listen_fd = -1, cli_fd = -1, srv_fd = -1, err;
 	socklen_t addrlen = sizeof(srv_sa6);
 	int srv_port;
 
@@ -161,6 +167,10 @@
 	if (CHECK_FAIL(cli_fd == -1))
 		goto done;
 
+	srv_fd = accept(listen_fd, NULL, NULL);
+	if (CHECK_FAIL(srv_fd == -1))
+		goto done;
+
 	if (CHECK(skel->bss->listen_tp_sport != srv_port,
 		  "Unexpected tp src port",
 		  "listen_tp_sport:%u expected:%u\n",
@@ -188,6 +198,8 @@
 		close(listen_fd);
 	if (cli_fd != -1)
 		close(cli_fd);
+	if (srv_fd != -1)
+		close(srv_fd);
 }
 
 struct test {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/cg_storage_multi.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/cg_storage_multi.c
@@ -56,8 +56,9 @@
 
 static bool connect_send(const char *cgroup_path)
 {
-	bool res = true;
 	int server_fd = -1, client_fd = -1;
+	char message[] = "message";
+	bool res = true;
 
 	if (join_cgroup(cgroup_path))
 		goto out_clean;
@@ -70,7 +71,10 @@
 	if (client_fd < 0)
 		goto out_clean;
 
-	if (send(client_fd, "message", strlen("message"), 0) < 0)
+	if (send(client_fd, &message, sizeof(message), 0) < 0)
+		goto out_clean;
+
+	if (read(server_fd, &message, sizeof(message)) < 0)
 		goto out_clean;
 
 	res = false;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/check_mtu.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/check_mtu.c
@@ -197,7 +197,7 @@
 
 void test_check_mtu(void)
 {
-	__u32 mtu_lo;
+	int mtu_lo;
 
 	if (test__start_subtest("bpf_check_mtu XDP-attach"))
 		test_check_mtu_xdp_attach();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/core_reloc.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/core_reloc.c
@@ -1,4 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
+#define _GNU_SOURCE
 #include <test_progs.h>
 #include "progs/core_reloc_types.h"
 #include "bpf_testmod/bpf_testmod.h"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/fexit_bpf2bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/fexit_bpf2bpf.c
@@ -371,6 +371,18 @@
 				     "./test_attach_probe.o");
 }
 
+static void test_func_replace_global_func(void)
+{
+	const char *prog_name[] = {
+		"freplace/test_pkt_access",
+	};
+
+	test_fexit_bpf2bpf_common("./freplace_global_func.o",
+				  "./test_pkt_access.o",
+				  ARRAY_SIZE(prog_name),
+				  prog_name, false, NULL);
+}
+
 void test_fexit_bpf2bpf(void)
 {
 	if (test__start_subtest("target_no_callees"))
@@ -391,4 +403,6 @@
 		test_func_replace_multi();
 	if (test__start_subtest("fmod_ret_freplace"))
 		test_fmod_ret_freplace();
+	if (test__start_subtest("func_replace_global_func"))
+		test_func_replace_global_func();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/flow_dissector.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/flow_dissector.c
@@ -1,4 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
+#define _GNU_SOURCE
 #include <test_progs.h>
 #include <network_helpers.h>
 #include <error.h>
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/get_stackid_cannot_attach.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/get_stackid_cannot_attach.c
@@ -65,6 +65,7 @@
 	skel->links.oncpu = bpf_program__attach_perf_event(skel->progs.oncpu,
 							   pmu_fd);
 	ASSERT_OK_PTR(skel->links.oncpu, "attach_perf_event_callchain");
+	bpf_link__destroy(skel->links.oncpu);
 	close(pmu_fd);
 
 	/* add exclude_callchain_kernel, attach should fail */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/kfree_skb.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/kfree_skb.c
@@ -1,4 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
+#define _GNU_SOURCE
 #include <test_progs.h>
 #include <network_helpers.h>
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/ksyms_btf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/ksyms_btf.c
@@ -7,6 +7,7 @@
 #include "test_ksyms_btf.skel.h"
 #include "test_ksyms_btf_null_check.skel.h"
 #include "test_ksyms_weak.skel.h"
+#include "test_ksyms_btf_write_check.skel.h"
 
 static int duration;
 
@@ -109,6 +110,16 @@
 	test_ksyms_weak__destroy(skel);
 }
 
+static void test_write_check(void)
+{
+	struct test_ksyms_btf_write_check *skel;
+
+	skel = test_ksyms_btf_write_check__open_and_load();
+	ASSERT_ERR_PTR(skel, "unexpected load of a prog writing to ksym memory\n");
+
+	test_ksyms_btf_write_check__destroy(skel);
+}
+
 void test_ksyms_btf(void)
 {
 	int percpu_datasec;
@@ -136,4 +147,7 @@
 
 	if (test__start_subtest("weak_ksyms"))
 		test_weak_syms();
+
+	if (test__start_subtest("write_check"))
+		test_write_check();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/migrate_reuseport.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/migrate_reuseport.c
@@ -204,8 +204,8 @@
 {
 	int err;
 
-	err = bpf_link__detach(test_case->link);
-	if (!ASSERT_OK(err, "bpf_link__detach"))
+	err = bpf_link__destroy(test_case->link);
+	if (!ASSERT_OK(err, "bpf_link__destroy"))
 		return -1;
 
 	test_case->link = NULL;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/perf_buffer.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/perf_buffer.c
@@ -107,8 +107,8 @@
 		  "expect %d, seen %d\n", nr_on_cpus, CPU_COUNT(&cpu_seen)))
 		goto out_free_pb;
 
-	if (CHECK(perf_buffer__buffer_cnt(pb) != nr_cpus, "buf_cnt",
-		  "got %zu, expected %d\n", perf_buffer__buffer_cnt(pb), nr_cpus))
+	if (CHECK(perf_buffer__buffer_cnt(pb) != nr_on_cpus, "buf_cnt",
+		  "got %zu, expected %d\n", perf_buffer__buffer_cnt(pb), nr_on_cpus))
 		goto out_close;
 
 	for (i = 0; i < nr_cpus; i++) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/send_signal.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/send_signal.c
@@ -149,7 +149,8 @@
 static void test_send_signal_perf(bool signal_thread)
 {
 	struct perf_event_attr attr = {
-		.sample_period = 1,
+		.freq = 1,
+		.sample_freq = 1000,
 		.type = PERF_TYPE_SOFTWARE,
 		.config = PERF_COUNT_SW_CPU_CLOCK,
 	};
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/sk_assign.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/sk_assign.c
@@ -29,7 +29,23 @@
 static bool
 configure_stack(void)
 {
+	char tc_version[128];
 	char tc_cmd[BUFSIZ];
+	char *prog;
+	FILE *tc;
+
+	/* Check whether tc is built with libbpf. */
+	tc = popen("tc -V", "r");
+	if (CHECK_FAIL(!tc))
+		return false;
+	if (CHECK_FAIL(!fgets(tc_version, sizeof(tc_version), tc)))
+		return false;
+	if (strstr(tc_version, ", libbpf "))
+		prog = "test_sk_assign_libbpf.o";
+	else
+		prog = "test_sk_assign.o";
+	if (CHECK_FAIL(pclose(tc)))
+		return false;
 
 	/* Move to a new networking namespace */
 	if (CHECK_FAIL(unshare(CLONE_NEWNET)))
@@ -46,8 +62,8 @@
 	/* Load qdisc, BPF program */
 	if (CHECK_FAIL(system("tc qdisc add dev lo clsact")))
 		return false;
-	sprintf(tc_cmd, "%s %s %s %s", "tc filter add dev lo ingress bpf",
-		       "direct-action object-file ./test_sk_assign.o",
+	sprintf(tc_cmd, "%s %s %s %s %s", "tc filter add dev lo ingress bpf",
+		       "direct-action object-file", prog,
 		       "section classifier/sk_assign_test",
 		       (env.verbosity < VERBOSE_VERY) ? " 2>/dev/null" : "verbose");
 	if (CHECK(system(tc_cmd), "BPF load failed;",
@@ -129,15 +145,12 @@
 static ssize_t
 rcv_msg(int srv_client, int type)
 {
-	struct sockaddr_storage ss;
 	char buf[BUFSIZ];
-	socklen_t slen;
 
 	if (type == SOCK_STREAM)
 		return read(srv_client, &buf, sizeof(buf));
 	else
-		return recvfrom(srv_client, &buf, sizeof(buf), 0,
-				(struct sockaddr *)&ss, &slen);
+		return recvfrom(srv_client, &buf, sizeof(buf), 0, NULL, NULL);
 }
 
 static int
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/sk_lookup.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/sk_lookup.c
@@ -598,7 +598,7 @@
 
 static void run_lookup_prog(const struct test *t)
 {
-	int server_fds[MAX_SERVERS] = { -1 };
+	int server_fds[] = { [0 ... MAX_SERVERS - 1] = -1 };
 	int client_fd, reuse_conn_fd = -1;
 	struct bpf_link *lookup_link;
 	int i, err;
@@ -964,7 +964,7 @@
 
 	err = update_lookup_map(t->sock_map, SERVER_A, server1);
 	if (err)
-		goto detach;
+		goto close_srv1;
 
 	/* second server on destination address we should never reach */
 	server2 = make_server(t->sotype, t->connect_to.ip, t->connect_to.port,
@@ -1053,7 +1053,7 @@
 			  struct bpf_program *lookup_prog,
 			  const char *remote_ip, const char *local_ip)
 {
-	int server_fds[MAX_SERVERS] = { -1 };
+	int server_fds[] = { [0 ... MAX_SERVERS - 1] = -1 };
 	struct bpf_sk_lookup ctx;
 	__u64 server_cookie;
 	int i, err;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/skb_ctx.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/skb_ctx.c
@@ -105,4 +105,6 @@
 		   "ctx_out_mark",
 		   "skb->mark == %u, expected %d\n",
 		   skb.mark, 10);
+
+	bpf_object__close(obj);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/sock_fields.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/sock_fields.c
@@ -1,9 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0
 /* Copyright (c) 2019 Facebook */
 
+#define _GNU_SOURCE
 #include <netinet/in.h>
 #include <arpa/inet.h>
 #include <unistd.h>
+#include <sched.h>
 #include <stdlib.h>
 #include <string.h>
 #include <errno.h>
@@ -21,6 +23,7 @@
 enum bpf_linum_array_idx {
 	EGRESS_LINUM_IDX,
 	INGRESS_LINUM_IDX,
+	READ_SK_DST_PORT_LINUM_IDX,
 	__NR_BPF_LINUM_ARRAY_IDX,
 };
 
@@ -43,8 +46,16 @@
 static int linum_map_fd;
 static __u32 duration;
 
-static __u32 egress_linum_idx = EGRESS_LINUM_IDX;
-static __u32 ingress_linum_idx = INGRESS_LINUM_IDX;
+static bool create_netns(void)
+{
+	if (!ASSERT_OK(unshare(CLONE_NEWNET), "create netns"))
+		return false;
+
+	if (!ASSERT_OK(system("ip link set dev lo up"), "bring up lo"))
+		return false;
+
+	return true;
+}
 
 static void print_sk(const struct bpf_sock *sk, const char *prefix)
 {
@@ -92,19 +103,24 @@
 {
 	struct bpf_tcp_sock srv_tp, cli_tp, listen_tp;
 	struct bpf_sock srv_sk, cli_sk, listen_sk;
-	__u32 ingress_linum, egress_linum;
+	__u32 idx, ingress_linum, egress_linum, linum;
 	int err;
 
-	err = bpf_map_lookup_elem(linum_map_fd, &egress_linum_idx,
-				  &egress_linum);
+	idx = EGRESS_LINUM_IDX;
+	err = bpf_map_lookup_elem(linum_map_fd, &idx, &egress_linum);
 	CHECK(err < 0, "bpf_map_lookup_elem(linum_map_fd)",
 	      "err:%d errno:%d\n", err, errno);
 
-	err = bpf_map_lookup_elem(linum_map_fd, &ingress_linum_idx,
-				  &ingress_linum);
+	idx = INGRESS_LINUM_IDX;
+	err = bpf_map_lookup_elem(linum_map_fd, &idx, &ingress_linum);
 	CHECK(err < 0, "bpf_map_lookup_elem(linum_map_fd)",
 	      "err:%d errno:%d\n", err, errno);
 
+	idx = READ_SK_DST_PORT_LINUM_IDX;
+	err = bpf_map_lookup_elem(linum_map_fd, &idx, &linum);
+	ASSERT_OK(err, "bpf_map_lookup_elem(linum_map_fd, READ_SK_DST_PORT_IDX)");
+	ASSERT_EQ(linum, 0, "failure in read_sk_dst_port on line");
+
 	memcpy(&srv_sk, &skel->bss->srv_sk, sizeof(srv_sk));
 	memcpy(&srv_tp, &skel->bss->srv_tp, sizeof(srv_tp));
 	memcpy(&cli_sk, &skel->bss->cli_sk, sizeof(cli_sk));
@@ -263,7 +279,7 @@
 	char buf[DATA_LEN];
 
 	/* Prepare listen_fd */
-	listen_fd = start_server(AF_INET6, SOCK_STREAM, "::1", 0, 0);
+	listen_fd = start_server(AF_INET6, SOCK_STREAM, "::1", 0xcafe, 0);
 	/* start_server() has logged the error details */
 	if (CHECK_FAIL(listen_fd == -1))
 		goto done;
@@ -331,8 +347,12 @@
 
 void test_sock_fields(void)
 {
-	struct bpf_link *egress_link = NULL, *ingress_link = NULL;
 	int parent_cg_fd = -1, child_cg_fd = -1;
+	struct bpf_link *link;
+
+	/* Use a dedicated netns to have a fixed listen port */
+	if (!create_netns())
+		return;
 
 	/* Create a cgroup, get fd, and join it */
 	parent_cg_fd = test__join_cgroup(PARENT_CGROUP);
@@ -353,15 +373,20 @@
 	if (CHECK(!skel, "test_sock_fields__open_and_load", "failed\n"))
 		goto done;
 
-	egress_link = bpf_program__attach_cgroup(skel->progs.egress_read_sock_fields,
-						 child_cg_fd);
-	if (!ASSERT_OK_PTR(egress_link, "attach_cgroup(egress)"))
+	link = bpf_program__attach_cgroup(skel->progs.egress_read_sock_fields, child_cg_fd);
+	if (!ASSERT_OK_PTR(link, "attach_cgroup(egress_read_sock_fields)"))
+		goto done;
+	skel->links.egress_read_sock_fields = link;
+
+	link = bpf_program__attach_cgroup(skel->progs.ingress_read_sock_fields, child_cg_fd);
+	if (!ASSERT_OK_PTR(link, "attach_cgroup(ingress_read_sock_fields)"))
 		goto done;
+	skel->links.ingress_read_sock_fields = link;
 
-	ingress_link = bpf_program__attach_cgroup(skel->progs.ingress_read_sock_fields,
-						  child_cg_fd);
-	if (!ASSERT_OK_PTR(ingress_link, "attach_cgroup(ingress)"))
+	link = bpf_program__attach_cgroup(skel->progs.read_sk_dst_port, child_cg_fd);
+	if (!ASSERT_OK_PTR(link, "attach_cgroup(read_sk_dst_port"))
 		goto done;
+	skel->links.read_sk_dst_port = link;
 
 	linum_map_fd = bpf_map__fd(skel->maps.linum_map);
 	sk_pkt_out_cnt_fd = bpf_map__fd(skel->maps.sk_pkt_out_cnt);
@@ -370,8 +395,7 @@
 	test();
 
 done:
-	bpf_link__destroy(egress_link);
-	bpf_link__destroy(ingress_link);
+	test_sock_fields__detach(skel);
 	test_sock_fields__destroy(skel);
 	if (child_cg_fd >= 0)
 		close(child_cg_fd);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/sockmap_listen.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/sockmap_listen.c
@@ -1911,7 +1911,7 @@
 	if (err)
 		return;
 
-	if (socketpair(AF_UNIX, SOCK_DGRAM | SOCK_NONBLOCK, 0, sfd))
+	if (socketpair(AF_UNIX, type | SOCK_NONBLOCK, 0, sfd))
 		goto close_cli0;
 	c1 = sfd[0], p1 = sfd[1];
 
@@ -1946,7 +1946,6 @@
 close_cli0:
 	xclose(c0);
 	xclose(p0);
-
 }
 
 static void unix_inet_skb_redir_to_connected(struct test_sockmap_listen *skel,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/sockopt_sk.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/sockopt_sk.c
@@ -3,6 +3,7 @@
 #include "cgroup_helpers.h"
 
 #include <linux/tcp.h>
+#include <linux/netlink.h>
 #include "sockopt_sk.skel.h"
 
 #ifndef SOL_TCP
@@ -183,6 +184,33 @@
 		goto err;
 	}
 
+	/* optval=NULL case is handled correctly */
+
+	close(fd);
+	fd = socket(AF_NETLINK, SOCK_RAW, 0);
+	if (fd < 0) {
+		log_err("Failed to create AF_NETLINK socket");
+		return -1;
+	}
+
+	buf.u32 = 1;
+	optlen = sizeof(__u32);
+	err = setsockopt(fd, SOL_NETLINK, NETLINK_ADD_MEMBERSHIP, &buf, optlen);
+	if (err) {
+		log_err("Unexpected getsockopt(NETLINK_ADD_MEMBERSHIP) err=%d errno=%d",
+			err, errno);
+		goto err;
+	}
+
+	optlen = 0;
+	err = getsockopt(fd, SOL_NETLINK, NETLINK_LIST_MEMBERSHIPS, NULL, &optlen);
+	if (err) {
+		log_err("Unexpected getsockopt(NETLINK_LIST_MEMBERSHIPS) err=%d errno=%d",
+			err, errno);
+		goto err;
+	}
+	ASSERT_EQ(optlen, 8, "Unexpected NETLINK_LIST_MEMBERSHIPS value");
+
 	free(big_buf);
 	close(fd);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/tailcalls.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/tailcalls.c
@@ -272,11 +272,11 @@
 
 	data_map = bpf_object__find_map_by_name(obj, "tailcall.bss");
 	if (CHECK_FAIL(!data_map || !bpf_map__is_internal(data_map)))
-		return;
+		goto out;
 
 	data_fd = bpf_map__fd(data_map);
-	if (CHECK_FAIL(map_fd < 0))
-		return;
+	if (CHECK_FAIL(data_fd < 0))
+		goto out;
 
 	i = 0;
 	err = bpf_map_lookup_elem(data_fd, &i, &val);
@@ -334,11 +334,11 @@
 
 	data_map = bpf_object__find_map_by_name(obj, "tailcall.bss");
 	if (CHECK_FAIL(!data_map || !bpf_map__is_internal(data_map)))
-		return;
+		goto out;
 
 	data_fd = bpf_map__fd(data_map);
-	if (CHECK_FAIL(map_fd < 0))
-		return;
+	if (CHECK_FAIL(data_fd < 0))
+		goto out;
 
 	for (i = 0; i < bpf_map__def(prog_array)->max_entries; i++) {
 		snprintf(prog_name, sizeof(prog_name), "classifier/%i", i);
@@ -422,11 +422,11 @@
 
 	data_map = bpf_object__find_map_by_name(obj, "tailcall.bss");
 	if (CHECK_FAIL(!data_map || !bpf_map__is_internal(data_map)))
-		return;
+		goto out;
 
 	data_fd = bpf_map__fd(data_map);
-	if (CHECK_FAIL(map_fd < 0))
-		return;
+	if (CHECK_FAIL(data_fd < 0))
+		goto out;
 
 	for (i = 0; i < bpf_map__def(prog_array)->max_entries; i++) {
 		snprintf(prog_name, sizeof(prog_name), "classifier/%i", i);
@@ -610,11 +610,11 @@
 
 	data_map = bpf_object__find_map_by_name(obj, "tailcall.bss");
 	if (CHECK_FAIL(!data_map || !bpf_map__is_internal(data_map)))
-		return;
+		goto out;
 
 	data_fd = bpf_map__fd(data_map);
-	if (CHECK_FAIL(map_fd < 0))
-		return;
+	if (CHECK_FAIL(data_fd < 0))
+		goto out;
 
 	i = 0;
 	err = bpf_map_lookup_elem(data_fd, &i, &val);
@@ -783,11 +783,11 @@
 
 	data_map = bpf_object__find_map_by_name(obj, "tailcall.bss");
 	if (CHECK_FAIL(!data_map || !bpf_map__is_internal(data_map)))
-		return;
+		goto out;
 
 	data_fd = bpf_map__fd(data_map);
-	if (CHECK_FAIL(map_fd < 0))
-		return;
+	if (CHECK_FAIL(data_fd < 0))
+		goto out;
 
 	i = 0;
 	val.noise = noise;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/tc_redirect.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/tc_redirect.c
@@ -105,6 +105,13 @@
 	if (!ASSERT_OK(err, "unshare"))
 		return err;
 
+	/* Make our /sys mount private, so the following umount won't
+	 * trigger the global umount in case it's shared.
+	 */
+	err = mount("none", "/sys", NULL, MS_PRIVATE, NULL);
+	if (!ASSERT_OK(err, "remount private /sys"))
+		return err;
+
 	err = umount2("/sys", MNT_DETACH);
 	if (!ASSERT_OK(err, "umount2 /sys"))
 		return err;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/tcp_rtt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/tcp_rtt.c
@@ -1,4 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
+#define _GNU_SOURCE
 #include <test_progs.h>
 #include "cgroup_helpers.h"
 #include "network_helpers.h"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/prog_tests/test_ima.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/prog_tests/test_ima.c
@@ -43,7 +43,7 @@
 void test_test_ima(void)
 {
 	char measured_dir_template[] = "/tmp/ima_measuredXXXXXX";
-	struct ring_buffer *ringbuf;
+	struct ring_buffer *ringbuf = NULL;
 	const char *measured_dir;
 	char cmd[256];
 
@@ -85,5 +85,6 @@
 	err = system(cmd);
 	CHECK(err, "failed to run command", "%s, errno = %d\n", cmd, errno);
 close_prog:
+	ring_buffer__free(ringbuf);
 	ima__destroy(skel);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/bpf_iter_task_stack.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/bpf_iter_task_stack.c
@@ -35,6 +35,8 @@
 	return 0;
 }
 
+int num_user_stacks = 0;
+
 SEC("iter/task")
 int get_task_user_stacks(struct bpf_iter__task *ctx)
 {
@@ -51,6 +53,9 @@
 	if (res <= 0)
 		return 0;
 
+	/* Only one task, the current one, should succeed */
+	++num_user_stacks;
+
 	buf_sz += res;
 
 	/* If the verifier doesn't refine bpf_get_task_stack res, and instead
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/btf_dump_test_case_bitfields.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/btf_dump_test_case_bitfields.c
@@ -53,7 +53,7 @@
  */
 /* ------ END-EXPECTED-OUTPUT ------ */
 struct bitfield_mixed_with_others {
-	long: 4; /* char is enough as a backing field */
+	char: 4; /* char is enough as a backing field */
 	int a: 4;
 	/* 8-bit implicit padding */
 	short b; /* combined with previous bitfield */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/btf_dump_test_case_multidim.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/btf_dump_test_case_multidim.c
@@ -14,9 +14,9 @@
 
 typedef int *ptr_multiarr_t[7][8][9][10];
 
-typedef int * (*fn_ptr_arr_t[11])();
+typedef int * (*fn_ptr_arr_t[11])(void);
 
-typedef int * (*fn_ptr_multiarr_t[12][13])();
+typedef int * (*fn_ptr_multiarr_t[12][13])(void);
 
 struct root_struct {
 	arr_t _1;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/btf_dump_test_case_packing.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/btf_dump_test_case_packing.c
@@ -58,7 +58,81 @@
 	} __attribute__((packed));
 };
 
-/*------ END-EXPECTED-OUTPUT ------ */
+/* ----- START-EXPECTED-OUTPUT ----- */
+/*
+ *struct nested_packed_but_aligned_struct {
+ *	int x1;
+ *	int x2;
+ *};
+ *
+ *struct outer_implicitly_packed_struct {
+ *	char y1;
+ *	struct nested_packed_but_aligned_struct y2;
+ *} __attribute__((packed));
+ *
+ */
+/* ------ END-EXPECTED-OUTPUT ------ */
+
+struct nested_packed_but_aligned_struct {
+	int x1;
+	int x2;
+} __attribute__((packed));
+
+struct outer_implicitly_packed_struct {
+	char y1;
+	struct nested_packed_but_aligned_struct y2;
+};
+/* ----- START-EXPECTED-OUTPUT ----- */
+/*
+ *struct usb_ss_ep_comp_descriptor {
+ *	char: 8;
+ *	char bDescriptorType;
+ *	char bMaxBurst;
+ *	short wBytesPerInterval;
+ *};
+ *
+ *struct usb_host_endpoint {
+ *	long: 64;
+ *	char: 8;
+ *	struct usb_ss_ep_comp_descriptor ss_ep_comp;
+ *	long: 0;
+ *} __attribute__((packed));
+ *
+ */
+/* ------ END-EXPECTED-OUTPUT ------ */
+
+struct usb_ss_ep_comp_descriptor {
+	char: 8;
+	char bDescriptorType;
+	char bMaxBurst;
+	int: 0;
+	short wBytesPerInterval;
+} __attribute__((packed));
+
+struct usb_host_endpoint {
+	long: 64;
+	char: 8;
+	struct usb_ss_ep_comp_descriptor ss_ep_comp;
+	long: 0;
+};
+
+/* ----- START-EXPECTED-OUTPUT ----- */
+struct nested_packed_struct {
+	int a;
+	char b;
+} __attribute__((packed));
+
+struct outer_nonpacked_struct {
+	short a;
+	struct nested_packed_struct b;
+};
+
+struct outer_packed_struct {
+	short a;
+	struct nested_packed_struct b;
+} __attribute__((packed));
+
+/* ------ END-EXPECTED-OUTPUT ------ */
 
 int f(struct {
 	struct packed_trailing_space _1;
@@ -69,6 +143,10 @@
 	union union_is_never_packed _6;
 	union union_does_not_need_packing _7;
 	union jump_code_union _8;
+	struct outer_implicitly_packed_struct _9;
+	struct usb_host_endpoint _10;
+	struct outer_nonpacked_struct _11;
+	struct outer_packed_struct _12;
 } *_)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/btf_dump_test_case_padding.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/btf_dump_test_case_padding.c
@@ -19,7 +19,7 @@
 /*
  *struct padded_explicitly {
  *	int a;
- *	int: 32;
+ *	long: 0;
  *	int b;
  *};
  *
@@ -28,41 +28,28 @@
 
 struct padded_explicitly {
 	int a;
-	int: 1; /* algo will explicitly pad with full 32 bits here */
+	int: 1; /* algo will emit aligning `long: 0;` here */
 	int b;
 };
 
 /* ----- START-EXPECTED-OUTPUT ----- */
-/*
- *struct padded_a_lot {
- *	int a;
- *	long: 32;
- *	long: 64;
- *	long: 64;
- *	int b;
- *};
- *
- */
-/* ------ END-EXPECTED-OUTPUT ------ */
-
 struct padded_a_lot {
 	int a;
-	/* 32 bit of implicit padding here, which algo will make explicit */
 	long: 64;
 	long: 64;
 	int b;
 };
 
+/* ------ END-EXPECTED-OUTPUT ------ */
+
 /* ----- START-EXPECTED-OUTPUT ----- */
 /*
  *struct padded_cache_line {
  *	int a;
- *	long: 32;
  *	long: 64;
  *	long: 64;
  *	long: 64;
  *	int b;
- *	long: 32;
  *	long: 64;
  *	long: 64;
  *	long: 64;
@@ -85,7 +72,7 @@
  *struct zone {
  *	int a;
  *	short b;
- *	short: 16;
+ *	long: 0;
  *	struct zone_padding __pad__;
  *};
  *
@@ -102,12 +89,160 @@
 	struct zone_padding __pad__;
 };
 
+/* ----- START-EXPECTED-OUTPUT ----- */
+struct padding_wo_named_members {
+	long: 64;
+	long: 64;
+};
+
+struct padding_weird_1 {
+	int a;
+	long: 64;
+	short: 16;
+	short b;
+};
+
+/* ------ END-EXPECTED-OUTPUT ------ */
+
+/* ----- START-EXPECTED-OUTPUT ----- */
+/*
+ *struct padding_weird_2 {
+ *	long: 56;
+ *	char a;
+ *	long: 56;
+ *	char b;
+ *	char: 8;
+ *};
+ *
+ */
+/* ------ END-EXPECTED-OUTPUT ------ */
+struct padding_weird_2 {
+	int: 32;	/* these paddings will be collapsed into `long: 56;` */
+	short: 16;
+	char: 8;
+	char a;
+	int: 32;	/* these paddings will be collapsed into `long: 56;` */
+	short: 16;
+	char: 8;
+	char b;
+	char: 8;
+};
+
+/* ----- START-EXPECTED-OUTPUT ----- */
+struct exact_1byte {
+	char x;
+};
+
+struct padded_1byte {
+	char: 8;
+};
+
+struct exact_2bytes {
+	short x;
+};
+
+struct padded_2bytes {
+	short: 16;
+};
+
+struct exact_4bytes {
+	int x;
+};
+
+struct padded_4bytes {
+	int: 32;
+};
+
+struct exact_8bytes {
+	long x;
+};
+
+struct padded_8bytes {
+	long: 64;
+};
+
+struct ff_periodic_effect {
+	int: 32;
+	short magnitude;
+	long: 0;
+	short phase;
+	long: 0;
+	int: 32;
+	int custom_len;
+	short *custom_data;
+};
+
+struct ib_wc {
+	long: 64;
+	long: 64;
+	int: 32;
+	int byte_len;
+	void *qp;
+	union {} ex;
+	long: 64;
+	int slid;
+	int wc_flags;
+	long: 64;
+	char smac[6];
+	long: 0;
+	char network_hdr_type;
+};
+
+struct acpi_object_method {
+	long: 64;
+	char: 8;
+	char type;
+	short reference_count;
+	char flags;
+	short: 0;
+	char: 8;
+	char sync_level;
+	long: 64;
+	void *node;
+	void *aml_start;
+	union {} dispatch;
+	long: 64;
+	int aml_length;
+};
+
+struct nested_unpacked {
+	int x;
+};
+
+struct nested_packed {
+	struct nested_unpacked a;
+	char c;
+} __attribute__((packed));
+
+struct outer_mixed_but_unpacked {
+	struct nested_packed b1;
+	short a1;
+	struct nested_packed b2;
+};
+
+/* ------ END-EXPECTED-OUTPUT ------ */
+
 int f(struct {
 	struct padded_implicitly _1;
 	struct padded_explicitly _2;
 	struct padded_a_lot _3;
 	struct padded_cache_line _4;
 	struct zone _5;
+	struct padding_wo_named_members _6;
+	struct padding_weird_1 _7;
+	struct padding_weird_2 _8;
+	struct exact_1byte _100;
+	struct padded_1byte _101;
+	struct exact_2bytes _102;
+	struct padded_2bytes _103;
+	struct exact_4bytes _104;
+	struct padded_4bytes _105;
+	struct exact_8bytes _106;
+	struct padded_8bytes _107;
+	struct ff_periodic_effect _200;
+	struct ib_wc _201;
+	struct acpi_object_method _202;
+	struct outer_mixed_but_unpacked _203;
 } *_)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/btf_dump_test_case_syntax.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/btf_dump_test_case_syntax.c
@@ -67,7 +67,7 @@
  *   `int -> char *` function and returns pointer to a char. Equivalent:
  *   typedef char * (*fn_input_t)(int);
  *   typedef char * (*fn_output_outer_t)(fn_input_t);
- *   typedef const fn_output_outer_t (* fn_output_inner_t)();
+ *   typedef const fn_output_outer_t (* fn_output_inner_t)(void);
  *   typedef const fn_output_inner_t fn_ptr_arr2_t[5];
  */
 /* ----- START-EXPECTED-OUTPUT ----- */
@@ -94,7 +94,7 @@
 
 typedef char * (*fn_ptr_arr1_t[10])(int **);
 
-typedef char * (* const (* const fn_ptr_arr2_t[5])())(char * (*)(int));
+typedef char * (* (* const fn_ptr_arr2_t[5])(void))(char * (*)(int));
 
 struct struct_w_typedefs {
 	int_t a;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/cg_storage_multi.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/cg_storage_multi.h
@@ -3,8 +3,6 @@
 #ifndef __PROGS_CG_STORAGE_MULTI_H
 #define __PROGS_CG_STORAGE_MULTI_H
 
-#include <asm/types.h>
-
 struct cgroup_value {
 	__u32 egress_pkts;
 	__u32 ingress_pkts;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/connect4_prog.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/connect4_prog.c
@@ -33,7 +33,7 @@
 
 int _version SEC("version") = 1;
 
-__attribute__ ((noinline))
+__attribute__ ((noinline)) __weak
 int do_bind(struct bpf_sock_addr *ctx)
 {
 	struct sockaddr_in sa = {};
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/freplace_global_func.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/freplace_global_func.c
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/bpf.h>
+#include <bpf/bpf_helpers.h>
+
+__noinline
+int test_ctx_global_func(struct __sk_buff *skb)
+{
+	volatile int retval = 1;
+	return retval;
+}
+
+SEC("freplace/test_pkt_access")
+int new_test_pkt_access(struct __sk_buff *skb)
+{
+	return test_ctx_global_func(skb);
+}
+
+char _license[] SEC("license") = "GPL";
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/profiler.inc.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/profiler.inc.h
@@ -826,8 +826,9 @@
 
 SEC("kprobe/vfs_link")
 int BPF_KPROBE(kprobe__vfs_link,
-	       struct dentry* old_dentry, struct inode* dir,
-	       struct dentry* new_dentry, struct inode** delegated_inode)
+	       struct dentry* old_dentry, struct user_namespace *mnt_userns,
+	       struct inode* dir, struct dentry* new_dentry,
+	       struct inode** delegated_inode)
 {
 	struct bpf_func_stats_ctx stats_ctx;
 	bpf_stats_enter(&stats_ctx, profiler_bpf_vfs_link);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/pyperf180.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/pyperf180.c
@@ -1,4 +1,26 @@
 // SPDX-License-Identifier: GPL-2.0
 // Copyright (c) 2019 Facebook
 #define STACK_MAX_LEN 180
+
+/* llvm upstream commit at clang18
+ *   https://github.com/llvm/llvm-project/commit/1a2e77cf9e11dbf56b5720c607313a566eebb16e
+ * changed inlining behavior and caused compilation failure as some branch
+ * target distance exceeded 16bit representation which is the maximum for
+ * cpu v1/v2/v3. Macro __BPF_CPU_VERSION__ is later implemented in clang18
+ * to specify which cpu version is used for compilation. So a smaller
+ * unroll_count can be set if __BPF_CPU_VERSION__ is less than 4, which
+ * reduced some branch target distances and resolved the compilation failure.
+ *
+ * To capture the case where a developer/ci uses clang18 but the corresponding
+ * repo checkpoint does not have __BPF_CPU_VERSION__, a smaller unroll_count
+ * will be set as well to prevent potential compilation failures.
+ */
+#ifdef __BPF_CPU_VERSION__
+#if __BPF_CPU_VERSION__ < 4
+#define UNROLL_COUNT 90
+#endif
+#elif __clang_major__ == 18
+#define UNROLL_COUNT 90
+#endif
+
 #include "pyperf.h"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/sockopt_sk.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/sockopt_sk.c
@@ -32,6 +32,12 @@
 	__u8 *optval_end = ctx->optval_end;
 	__u8 *optval = ctx->optval;
 	struct sockopt_sk *storage;
+	struct bpf_sock *sk;
+
+	/* Bypass AF_NETLINK. */
+	sk = ctx->sk;
+	if (sk && sk->family == AF_NETLINK)
+		return 1;
 
 	/* Make sure bpf_get_netns_cookie is callable.
 	 */
@@ -130,6 +136,12 @@
 	__u8 *optval_end = ctx->optval_end;
 	__u8 *optval = ctx->optval;
 	struct sockopt_sk *storage;
+	struct bpf_sock *sk;
+
+	/* Bypass AF_NETLINK. */
+	sk = ctx->sk;
+	if (sk && sk->family == AF_NETLINK)
+		return 1;
 
 	/* Make sure bpf_get_netns_cookie is callable.
 	 */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/strobemeta.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/strobemeta.h
@@ -358,7 +358,7 @@
 					     void *payload)
 {
 	void *location;
-	uint32_t len;
+	uint64_t len;
 
 	data->str_lens[idx] = 0;
 	location = calc_location(&cfg->str_locs[idx], tls_base);
@@ -390,7 +390,7 @@
 	struct strobe_map_descr* descr = &data->map_descrs[idx];
 	struct strobe_map_raw map;
 	void *location;
-	uint32_t len;
+	uint64_t len;
 	int i;
 
 	descr->tag_len = 0; /* presume no tag is set */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_cls_redirect.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_cls_redirect.h
@@ -12,6 +12,15 @@
 #include <linux/ipv6.h>
 #include <linux/udp.h>
 
+/* offsetof() is used in static asserts, and the libbpf-redefined CO-RE
+ * friendly version breaks compilation for older clang versions <= 15
+ * when invoked in a static assert.  Restore original here.
+ */
+#ifdef offsetof
+#undef offsetof
+#define offsetof(type, member) __builtin_offsetof(type, member)
+#endif
+
 struct gre_base_hdr {
 	uint16_t flags;
 	uint16_t protocol;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_ksyms_btf_write_check.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_ksyms_btf_write_check.c
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2021 Google */
+
+#include "vmlinux.h"
+
+#include <bpf/bpf_helpers.h>
+
+extern const int bpf_prog_active __ksym; /* int type global var. */
+
+SEC("raw_tp/sys_enter")
+int handler(const void *ctx)
+{
+	int *active;
+	__u32 cpu;
+
+	cpu = bpf_get_smp_processor_id();
+	active = (int *)bpf_per_cpu_ptr(&bpf_prog_active, cpu);
+	if (active) {
+		/* Kernel memory obtained from bpf_{per,this}_cpu_ptr
+		 * is read-only, should _not_ pass verification.
+		 */
+		/* WRITE_ONCE */
+		*(volatile int *)active = -1;
+	}
+
+	return 0;
+}
+
+char _license[] SEC("license") = "GPL";
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_map_in_map.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_map_in_map.c
@@ -23,7 +23,7 @@
 	__uint(value_size, sizeof(__u32));
 } mim_hash SEC(".maps");
 
-SEC("xdp_mimtest")
+SEC("xdp")
 int xdp_mimtest0(struct xdp_md *ctx)
 {
 	int value = 123;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_sk_assign.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_sk_assign.c
@@ -16,6 +16,16 @@
 #include <bpf/bpf_helpers.h>
 #include <bpf/bpf_endian.h>
 
+#if defined(IPROUTE2_HAVE_LIBBPF)
+/* Use a new-style map definition. */
+struct {
+	__uint(type, BPF_MAP_TYPE_SOCKMAP);
+	__type(key, int);
+	__type(value, __u64);
+	__uint(pinning, LIBBPF_PIN_BY_NAME);
+	__uint(max_entries, 1);
+} server_map SEC(".maps");
+#else
 /* Pin map under /sys/fs/bpf/tc/globals/<map name> */
 #define PIN_GLOBAL_NS 2
 
@@ -35,6 +45,7 @@
 	.max_elem = 1,
 	.pinning = PIN_GLOBAL_NS,
 };
+#endif
 
 int _version SEC("version") = 1;
 char _license[] SEC("license") = "GPL";
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_sk_assign_libbpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_sk_assign_libbpf.c
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0
+#define IPROUTE2_HAVE_LIBBPF
+#include "test_sk_assign.c"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_sk_lookup.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_sk_lookup.c
@@ -404,8 +404,7 @@
 
 	/* Narrow loads from remote_port field. Expect SRC_PORT. */
 	if (LSB(ctx->remote_port, 0) != ((SRC_PORT >> 0) & 0xff) ||
-	    LSB(ctx->remote_port, 1) != ((SRC_PORT >> 8) & 0xff) ||
-	    LSB(ctx->remote_port, 2) != 0 || LSB(ctx->remote_port, 3) != 0)
+	    LSB(ctx->remote_port, 1) != ((SRC_PORT >> 8) & 0xff))
 		return SK_DROP;
 	if (LSW(ctx->remote_port, 0) != SRC_PORT)
 		return SK_DROP;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_sock_fields.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_sock_fields.c
@@ -12,6 +12,7 @@
 enum bpf_linum_array_idx {
 	EGRESS_LINUM_IDX,
 	INGRESS_LINUM_IDX,
+	READ_SK_DST_PORT_LINUM_IDX,
 	__NR_BPF_LINUM_ARRAY_IDX,
 };
 
@@ -113,7 +114,7 @@
 
 #define RET_LOG() ({						\
 	linum = __LINE__;					\
-	bpf_map_update_elem(&linum_map, &linum_idx, &linum, BPF_NOEXIST);	\
+	bpf_map_update_elem(&linum_map, &linum_idx, &linum, BPF_ANY);	\
 	return CG_OK;						\
 })
 
@@ -249,5 +250,49 @@
 
 	return CG_OK;
 }
+
+static __noinline bool sk_dst_port__load_word(struct bpf_sock *sk)
+{
+	__u32 *word = (__u32 *)&sk->dst_port;
+	return word[0] == bpf_htonl(0xcafe0000);
+}
+
+static __noinline bool sk_dst_port__load_half(struct bpf_sock *sk)
+{
+	__u16 *half = (__u16 *)&sk->dst_port;
+	return half[0] == bpf_htons(0xcafe);
+}
+
+static __noinline bool sk_dst_port__load_byte(struct bpf_sock *sk)
+{
+	__u8 *byte = (__u8 *)&sk->dst_port;
+	return byte[0] == 0xca && byte[1] == 0xfe;
+}
+
+SEC("cgroup_skb/egress")
+int read_sk_dst_port(struct __sk_buff *skb)
+{
+	__u32 linum, linum_idx;
+	struct bpf_sock *sk;
+
+	linum_idx = READ_SK_DST_PORT_LINUM_IDX;
+
+	sk = skb->sk;
+	if (!sk)
+		RET_LOG();
+
+	/* Ignore everything but the SYN from the client socket */
+	if (sk->state != BPF_TCP_SYN_SENT)
+		return CG_OK;
+
+	if (!sk_dst_port__load_word(sk))
+		RET_LOG();
+	if (!sk_dst_port__load_half(sk))
+		RET_LOG();
+	if (!sk_dst_port__load_byte(sk))
+		RET_LOG();
+
+	return CG_OK;
+}
 
 char _license[] SEC("license") = "GPL";
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_sockmap_kern.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_sockmap_kern.h
@@ -235,7 +235,7 @@
 int bpf_prog4(struct sk_msg_md *msg)
 {
 	int *bytes, zero = 0, one = 1, two = 2, three = 3, four = 4, five = 5;
-	int *start, *end, *start_push, *end_push, *start_pop, *pop;
+	int *start, *end, *start_push, *end_push, *start_pop, *pop, err = 0;
 
 	bytes = bpf_map_lookup_elem(&sock_apply_bytes, &zero);
 	if (bytes)
@@ -249,8 +249,11 @@
 		bpf_msg_pull_data(msg, *start, *end, 0);
 	start_push = bpf_map_lookup_elem(&sock_bytes, &two);
 	end_push = bpf_map_lookup_elem(&sock_bytes, &three);
-	if (start_push && end_push)
-		bpf_msg_push_data(msg, *start_push, *end_push, 0);
+	if (start_push && end_push) {
+		err = bpf_msg_push_data(msg, *start_push, *end_push, 0);
+		if (err)
+			return SK_DROP;
+	}
 	start_pop = bpf_map_lookup_elem(&sock_bytes, &four);
 	pop = bpf_map_lookup_elem(&sock_bytes, &five);
 	if (start_pop && pop)
@@ -263,6 +266,7 @@
 {
 	int zero = 0, one = 1, two = 2, three = 3, four = 4, five = 5, key = 0;
 	int *bytes, *start, *end, *start_push, *end_push, *start_pop, *pop, *f;
+	int err = 0;
 	__u64 flags = 0;
 
 	bytes = bpf_map_lookup_elem(&sock_apply_bytes, &zero);
@@ -279,8 +283,11 @@
 
 	start_push = bpf_map_lookup_elem(&sock_bytes, &two);
 	end_push = bpf_map_lookup_elem(&sock_bytes, &three);
-	if (start_push && end_push)
-		bpf_msg_push_data(msg, *start_push, *end_push, 0);
+	if (start_push && end_push) {
+		err = bpf_msg_push_data(msg, *start_push, *end_push, 0);
+		if (err)
+			return SK_DROP;
+	}
 
 	start_pop = bpf_map_lookup_elem(&sock_bytes, &four);
 	pop = bpf_map_lookup_elem(&sock_bytes, &five);
@@ -338,7 +345,7 @@
 int bpf_prog10(struct sk_msg_md *msg)
 {
 	int *bytes, *start, *end, *start_push, *end_push, *start_pop, *pop;
-	int zero = 0, one = 1, two = 2, three = 3, four = 4, five = 5;
+	int zero = 0, one = 1, two = 2, three = 3, four = 4, five = 5, err = 0;
 
 	bytes = bpf_map_lookup_elem(&sock_apply_bytes, &zero);
 	if (bytes)
@@ -352,8 +359,11 @@
 		bpf_msg_pull_data(msg, *start, *end, 0);
 	start_push = bpf_map_lookup_elem(&sock_bytes, &two);
 	end_push = bpf_map_lookup_elem(&sock_bytes, &three);
-	if (start_push && end_push)
-		bpf_msg_push_data(msg, *start_push, *end_push, 0);
+	if (start_push && end_push) {
+		err = bpf_msg_push_data(msg, *start_push, *end_push, 0);
+		if (err)
+			return SK_PASS;
+	}
 	start_pop = bpf_map_lookup_elem(&sock_bytes, &four);
 	pop = bpf_map_lookup_elem(&sock_bytes, &five);
 	if (start_pop && pop)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_stacktrace_build_id.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_stacktrace_build_id.c
@@ -39,16 +39,8 @@
 	__type(value, stack_trace_t);
 } stack_amap SEC(".maps");
 
-/* taken from /sys/kernel/debug/tracing/events/random/urandom_read/format */
-struct random_urandom_args {
-	unsigned long long pad;
-	int got_bits;
-	int pool_left;
-	int input_left;
-};
-
-SEC("tracepoint/random/urandom_read")
-int oncpu(struct random_urandom_args *args)
+SEC("kprobe/urandom_read_iter")
+int oncpu(struct pt_regs *args)
 {
 	__u32 max_len = sizeof(struct bpf_stack_build_id)
 			* PERF_MAX_STACK_DEPTH;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_tcp_check_syncookie_kern.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_tcp_check_syncookie_kern.c
@@ -156,7 +156,7 @@
 	return TC_ACT_OK;
 }
 
-SEC("xdp/check_syncookie")
+SEC("xdp")
 int check_syncookie_xdp(struct xdp_md *ctx)
 {
 	check_syncookie(ctx, (void *)(long)ctx->data,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp.c
@@ -210,7 +210,7 @@
 	return XDP_TX;
 }
 
-SEC("xdp_tx_iptunnel")
+SEC("xdp")
 int _xdp_tx_iptunnel(struct xdp_md *xdp)
 {
 	void *data_end = (void *)(long)xdp->data_end;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_adjust_tail_grow.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_adjust_tail_grow.c
@@ -2,7 +2,7 @@
 #include <linux/bpf.h>
 #include <bpf/bpf_helpers.h>
 
-SEC("xdp_adjust_tail_grow")
+SEC("xdp")
 int _xdp_adjust_tail_grow(struct xdp_md *xdp)
 {
 	void *data_end = (void *)(long)xdp->data_end;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_adjust_tail_shrink.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_adjust_tail_shrink.c
@@ -9,9 +9,7 @@
 #include <linux/if_ether.h>
 #include <bpf/bpf_helpers.h>
 
-int _version SEC("version") = 1;
-
-SEC("xdp_adjust_tail_shrink")
+SEC("xdp")
 int _xdp_adjust_tail_shrink(struct xdp_md *xdp)
 {
 	void *data_end = (void *)(long)xdp->data_end;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_devmap_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_devmap_helpers.c
@@ -5,7 +5,7 @@
 #include <linux/bpf.h>
 #include <bpf/bpf_helpers.h>
 
-SEC("xdp_dm_log")
+SEC("xdp")
 int xdpdm_devlog(struct xdp_md *ctx)
 {
 	char fmt[] = "devmap redirect: dev %u -> dev %u len %u\n";
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_link.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_link.c
@@ -5,7 +5,7 @@
 
 char LICENSE[] SEC("license") = "GPL";
 
-SEC("xdp/handler")
+SEC("xdp")
 int xdp_handler(struct xdp_md *xdp)
 {
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_loop.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_loop.c
@@ -206,7 +206,7 @@
 	return XDP_TX;
 }
 
-SEC("xdp_tx_iptunnel")
+SEC("xdp")
 int _xdp_tx_iptunnel(struct xdp_md *xdp)
 {
 	void *data_end = (void *)(long)xdp->data_end;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_noinline.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_noinline.c
@@ -797,7 +797,7 @@
 	return XDP_DROP;
 }
 
-SEC("xdp-test-v4")
+SEC("xdp")
 int balancer_ingress_v4(struct xdp_md *ctx)
 {
 	void *data = (void *)(long)ctx->data;
@@ -816,7 +816,7 @@
 		return XDP_DROP;
 }
 
-SEC("xdp-test-v6")
+SEC("xdp")
 int balancer_ingress_v6(struct xdp_md *ctx)
 {
 	void *data = (void *)(long)ctx->data;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_with_cpumap_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_with_cpumap_helpers.c
@@ -12,13 +12,13 @@
 	__uint(max_entries, 4);
 } cpu_map SEC(".maps");
 
-SEC("xdp_redir")
+SEC("xdp")
 int xdp_redir_prog(struct xdp_md *ctx)
 {
 	return bpf_redirect_map(&cpu_map, 1, 0);
 }
 
-SEC("xdp_dummy")
+SEC("xdp")
 int xdp_dummy_prog(struct xdp_md *ctx)
 {
 	return XDP_PASS;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/test_xdp_with_devmap_helpers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/test_xdp_with_devmap_helpers.c
@@ -9,7 +9,7 @@
 	__uint(max_entries, 4);
 } dm_ports SEC(".maps");
 
-SEC("xdp_redir")
+SEC("xdp")
 int xdp_redir_prog(struct xdp_md *ctx)
 {
 	return bpf_redirect_map(&dm_ports, 1, 0);
@@ -18,7 +18,7 @@
 /* invalid program on DEVMAP entry;
  * SEC name means expected attach type not set
  */
-SEC("xdp_dummy")
+SEC("xdp")
 int xdp_dummy_prog(struct xdp_md *ctx)
 {
 	return XDP_PASS;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/xdp_dummy.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/xdp_dummy.c
@@ -4,7 +4,7 @@
 #include <linux/bpf.h>
 #include <bpf/bpf_helpers.h>
 
-SEC("xdp_dummy")
+SEC("xdp")
 int xdp_dummy_prog(struct xdp_md *ctx)
 {
 	return XDP_PASS;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/xdp_redirect_multi_kern.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/xdp_redirect_multi_kern.c
@@ -34,7 +34,7 @@
 	__uint(max_entries, 128);
 } mac_map SEC(".maps");
 
-SEC("xdp_redirect_map_multi")
+SEC("xdp")
 int xdp_redirect_map_multi_prog(struct xdp_md *ctx)
 {
 	void *data_end = (void *)(long)ctx->data_end;
@@ -63,7 +63,7 @@
 }
 
 /* The following 2 progs are for 2nd devmap prog testing */
-SEC("xdp_redirect_map_ingress")
+SEC("xdp")
 int xdp_redirect_map_all_prog(struct xdp_md *ctx)
 {
 	return bpf_redirect_map(&map_egress, 0,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/progs/xdping_kern.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/progs/xdping_kern.c
@@ -86,7 +86,7 @@
 	return XDP_TX;
 }
 
-SEC("xdpclient")
+SEC("xdp")
 int xdping_client(struct xdp_md *ctx)
 {
 	void *data_end = (void *)(long)ctx->data_end;
@@ -150,7 +150,7 @@
 	return XDP_TX;
 }
 
-SEC("xdpserver")
+SEC("xdp")
 int xdping_server(struct xdp_md *ctx)
 {
 	void *data_end = (void *)(long)ctx->data_end;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_bpftool_synctypes.py
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_bpftool_synctypes.py
@@ -172,7 +172,7 @@
         @enum_name: name of the enum to parse
         """
         start_marker = re.compile(f'enum {enum_name} {{\n')
-        pattern = re.compile('^\s*(BPF_\w+),?$')
+        pattern = re.compile('^\s*(BPF_\w+),?(\s+/\*.*\*/)?$')
         end_marker = re.compile('^};')
         parser = BlockParser(self.reader)
         parser.search_block(start_marker)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_cpp.cpp
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_cpp.cpp
@@ -3,6 +3,10 @@
 #include <bpf/libbpf.h>
 #include <bpf/bpf.h>
 #include <bpf/btf.h>
+
+#ifndef _Bool
+#define _Bool bool
+#endif
 #include "test_core_extern.skel.h"
 
 /* do nothing, just make sure we can link successfully */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_lirc_mode2.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_lirc_mode2.sh
@@ -3,6 +3,7 @@
 
 # Kselftest framework requirement - SKIP code is 4.
 ksft_skip=4
+ret=$ksft_skip
 
 msg="skip all tests:"
 if [ $UID != 0 ]; then
@@ -25,7 +26,7 @@
 	fi
 done
 
-if [ -n $LIRCDEV ];
+if [ -n "$LIRCDEV" ];
 then
 	TYPE=lirc_mode2
 	./test_lirc_mode2_user $LIRCDEV $INPUTDEV
@@ -36,3 +37,5 @@
 		echo -e ${GREEN}"PASS: $TYPE"${NC}
 	fi
 fi
+
+exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_lru_map.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_lru_map.c
@@ -137,7 +137,8 @@
 
 	while (next < nr_cpus) {
 		CPU_ZERO(&cpuset);
-		CPU_SET(next++, &cpuset);
+		CPU_SET(next, &cpuset);
+		next++;
 		if (!sched_setaffinity(pid, sizeof(cpuset), &cpuset)) {
 			ret = 0;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_lwt_ip_encap.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_lwt_ip_encap.sh
@@ -120,6 +120,14 @@
 	ip netns exec ${NS2} sysctl -wq net.ipv4.conf.default.rp_filter=0
 	ip netns exec ${NS3} sysctl -wq net.ipv4.conf.default.rp_filter=0
 
+	# disable IPv6 DAD because it sometimes takes too long and fails tests
+	ip netns exec ${NS1} sysctl -wq net.ipv6.conf.all.accept_dad=0
+	ip netns exec ${NS2} sysctl -wq net.ipv6.conf.all.accept_dad=0
+	ip netns exec ${NS3} sysctl -wq net.ipv6.conf.all.accept_dad=0
+	ip netns exec ${NS1} sysctl -wq net.ipv6.conf.default.accept_dad=0
+	ip netns exec ${NS2} sysctl -wq net.ipv6.conf.default.accept_dad=0
+	ip netns exec ${NS3} sysctl -wq net.ipv6.conf.default.accept_dad=0
+
 	ip link add veth1 type veth peer name veth2
 	ip link add veth3 type veth peer name veth4
 	ip link add veth5 type veth peer name veth6
@@ -289,7 +297,7 @@
 		ip netns exec ${NS1} ping  -c 1 -W 1 -I veth1 ${IPv4_DST} 2>&1 > /dev/null
 		RET=$?
 	elif [ "${PROTO}" == "IPv6" ] ; then
-		ip netns exec ${NS1} ping6 -c 1 -W 6 -I veth1 ${IPv6_DST} 2>&1 > /dev/null
+		ip netns exec ${NS1} ping6 -c 1 -W 1 -I veth1 ${IPv6_DST} 2>&1 > /dev/null
 		RET=$?
 	else
 		echo "    test_ping: unknown PROTO: ${PROTO}"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_progs.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_progs.c
@@ -370,7 +370,7 @@
 
 	if (getline(&line, &len, fp) == -1)
 		goto err;
-	fclose(fp);
+	pclose(fp);
 
 	if (len > size)
 		len = size;
@@ -379,7 +379,7 @@
 	free(line);
 	return 0;
 err:
-	fclose(fp);
+	pclose(fp);
 	return -1;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_sockmap.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_sockmap.c
@@ -58,6 +58,8 @@
 #define BPF_SOCKHASH_FILENAME "test_sockhash_kern.o"
 #define CG_PATH "/sockmap"
 
+#define EDATAINTEGRITY 2001
+
 /* global sockets */
 int s1, s2, c1, c2, p1, p2;
 int test_cnt;
@@ -65,7 +67,7 @@
 int failed;
 int map_fd[9];
 struct bpf_map *maps[9];
-int prog_fd[11];
+int prog_fd[9];
 
 int txmsg_pass;
 int txmsg_redir;
@@ -87,6 +89,10 @@
 int peek_flag;
 int skb_use_parser;
 int txmsg_omit_skb_parser;
+int verify_push_start;
+int verify_push_len;
+int verify_pop_start;
+int verify_pop_len;
 
 static const struct option long_options[] = {
 	{"help",	no_argument,		NULL, 'h' },
@@ -139,6 +145,7 @@
 	bool sendpage;
 	bool data_test;
 	bool drop_expected;
+	bool check_recved_len;
 	int iov_count;
 	int iov_length;
 	int rate;
@@ -417,16 +424,18 @@
 {
 	bool drop = opt->drop_expected;
 	unsigned char k = 0;
+	int i, j, fp;
 	FILE *file;
-	int i, fp;
 
 	file = tmpfile();
 	if (!file) {
 		perror("create file for sendpage");
 		return 1;
 	}
-	for (i = 0; i < iov_length * cnt; i++, k++)
-		fwrite(&k, sizeof(char), 1, file);
+	for (i = 0; i < cnt; i++, k = 0) {
+		for (j = 0; j < iov_length; j++, k++)
+			fwrite(&k, sizeof(char), 1, file);
+	}
 	fflush(file);
 	fseek(file, 0, SEEK_SET);
 
@@ -509,42 +518,111 @@
 	return -ENOMEM;
 }
 
-static int msg_verify_data(struct msghdr *msg, int size, int chunk_sz)
+/* In push or pop test, we need to do some calculations for msg_verify_data */
+static void msg_verify_date_prep(void)
 {
-	int i, j = 0, bytes_cnt = 0;
-	unsigned char k = 0;
+	int push_range_end = txmsg_start_push + txmsg_end_push - 1;
+	int pop_range_end = txmsg_start_pop + txmsg_pop - 1;
+
+	if (txmsg_end_push && txmsg_pop &&
+	    txmsg_start_push <= pop_range_end && txmsg_start_pop <= push_range_end) {
+		/* The push range and the pop range overlap */
+		int overlap_len;
+
+		verify_push_start = txmsg_start_push;
+		verify_pop_start = txmsg_start_pop;
+		if (txmsg_start_push < txmsg_start_pop)
+			overlap_len = min(push_range_end - txmsg_start_pop + 1, txmsg_pop);
+		else
+			overlap_len = min(pop_range_end - txmsg_start_push + 1, txmsg_end_push);
+		verify_push_len = max(txmsg_end_push - overlap_len, 0);
+		verify_pop_len = max(txmsg_pop - overlap_len, 0);
+	} else {
+		/* Otherwise */
+		verify_push_start = txmsg_start_push;
+		verify_pop_start = txmsg_start_pop;
+		verify_push_len = txmsg_end_push;
+		verify_pop_len = txmsg_pop;
+	}
+}
 
-	for (i = 0; i < msg->msg_iovlen; i++) {
+static int msg_verify_data(struct msghdr *msg, int size, int chunk_sz,
+			   unsigned char *k_p, int *bytes_cnt_p,
+			   int *check_cnt_p, int *push_p)
+{
+	int bytes_cnt = *bytes_cnt_p, check_cnt = *check_cnt_p, push = *push_p;
+	unsigned char k = *k_p;
+	int i, j;
+
+	for (i = 0, j = 0; i < msg->msg_iovlen && size; i++, j = 0) {
 		unsigned char *d = msg->msg_iov[i].iov_base;
 
 		/* Special case test for skb ingress + ktls */
 		if (i == 0 && txmsg_ktls_skb) {
 			if (msg->msg_iov[i].iov_len < 4)
-				return -EIO;
+				return -EDATAINTEGRITY;
 			if (memcmp(d, "PASS", 4) != 0) {
 				fprintf(stderr,
 					"detected skb data error with skb ingress update @iov[%i]:%i \"%02x %02x %02x %02x\" != \"PASS\"\n",
 					i, 0, d[0], d[1], d[2], d[3]);
-				return -EIO;
+				return -EDATAINTEGRITY;
 			}
 			j = 4; /* advance index past PASS header */
 		}
 
 		for (; j < msg->msg_iov[i].iov_len && size; j++) {
+			if (push > 0 &&
+			    check_cnt == verify_push_start + verify_push_len - push) {
+				int skipped;
+revisit_push:
+				skipped = push;
+				if (j + push >= msg->msg_iov[i].iov_len)
+					skipped = msg->msg_iov[i].iov_len - j;
+				push -= skipped;
+				size -= skipped;
+				j += skipped - 1;
+				check_cnt += skipped;
+				continue;
+			}
+
+			if (verify_pop_len > 0 && check_cnt == verify_pop_start) {
+				bytes_cnt += verify_pop_len;
+				check_cnt += verify_pop_len;
+				k += verify_pop_len;
+
+				if (bytes_cnt == chunk_sz) {
+					k = 0;
+					bytes_cnt = 0;
+					check_cnt = 0;
+					push = verify_push_len;
+				}
+
+				if (push > 0 &&
+				    check_cnt == verify_push_start + verify_push_len - push)
+					goto revisit_push;
+			}
+
 			if (d[j] != k++) {
 				fprintf(stderr,
 					"detected data corruption @iov[%i]:%i %02x != %02x, %02x ?= %02x\n",
 					i, j, d[j], k - 1, d[j+1], k);
-				return -EIO;
+				return -EDATAINTEGRITY;
 			}
 			bytes_cnt++;
+			check_cnt++;
 			if (bytes_cnt == chunk_sz) {
 				k = 0;
 				bytes_cnt = 0;
+				check_cnt = 0;
+				push = verify_push_len;
 			}
 			size--;
 		}
 	}
+	*k_p = k;
+	*bytes_cnt_p = bytes_cnt;
+	*check_cnt_p = check_cnt;
+	*push_p = push;
 	return 0;
 }
 
@@ -556,8 +634,12 @@
 	int err, i, flags = MSG_NOSIGNAL;
 	bool drop = opt->drop_expected;
 	bool data = opt->data_test;
+	int iov_alloc_length = iov_length;
 
-	err = msg_alloc_iov(&msg, iov_count, iov_length, data, tx);
+	if (!tx && opt->check_recved_len)
+		iov_alloc_length *= 2;
+
+	err = msg_alloc_iov(&msg, iov_count, iov_alloc_length, data, tx);
 	if (err)
 		goto out_errno;
 	if (peek_flag) {
@@ -589,10 +671,14 @@
 		}
 		clock_gettime(CLOCK_MONOTONIC, &s->end);
 	} else {
+		float total_bytes, txmsg_pop_total, txmsg_push_total;
 		int slct, recvp = 0, recv, max_fd = fd;
-		float total_bytes, txmsg_pop_total;
 		int fd_flags = O_NONBLOCK;
 		struct timeval timeout;
+		unsigned char k = 0;
+		int bytes_cnt = 0;
+		int check_cnt = 0;
+		int push = 0;
 		fd_set w;
 
 		fcntl(fd, fd_flags);
@@ -606,12 +692,22 @@
 		 * This is really only useful for testing edge cases in code
 		 * paths.
 		 */
-		total_bytes = (float)iov_count * (float)iov_length * (float)cnt;
-		if (txmsg_apply)
+		total_bytes = (float)iov_length * (float)cnt;
+		if (!opt->sendpage)
+			total_bytes *= (float)iov_count;
+		if (txmsg_apply) {
+			txmsg_push_total = txmsg_end_push * (total_bytes / txmsg_apply);
 			txmsg_pop_total = txmsg_pop * (total_bytes / txmsg_apply);
-		else
+		} else {
+			txmsg_push_total = txmsg_end_push * cnt;
 			txmsg_pop_total = txmsg_pop * cnt;
+		}
+		total_bytes += txmsg_push_total;
 		total_bytes -= txmsg_pop_total;
+		if (data) {
+			msg_verify_date_prep();
+			push = verify_push_len;
+		}
 		err = clock_gettime(CLOCK_MONOTONIC, &s->start);
 		if (err < 0)
 			perror("recv start time");
@@ -663,14 +759,23 @@
 				}
 			}
 
-			s->bytes_recvd += recv;
+			if (recv > 0)
+				s->bytes_recvd += recv;
+
+			if (opt->check_recved_len && s->bytes_recvd > total_bytes) {
+				errno = EMSGSIZE;
+				fprintf(stderr, "recv failed(), bytes_recvd:%zd, total_bytes:%f\n",
+						s->bytes_recvd, total_bytes);
+				goto out_errno;
+			}
 
 			if (data) {
 				int chunk_sz = opt->sendpage ?
-						iov_length * cnt :
+						iov_length :
 						iov_length * iov_count;
 
-				errno = msg_verify_data(&msg, recv, chunk_sz);
+				errno = msg_verify_data(&msg, recv, chunk_sz, &k, &bytes_cnt,
+							&check_cnt, &push);
 				if (errno) {
 					perror("data verify msg failed");
 					goto out_errno;
@@ -678,7 +783,11 @@
 				if (recvp) {
 					errno = msg_verify_data(&msg_peek,
 								recvp,
-								chunk_sz);
+								chunk_sz,
+								&k,
+								&bytes_cnt,
+								&check_cnt,
+								&push);
 					if (errno) {
 						perror("data verify msg_peek failed");
 						goto out_errno;
@@ -744,7 +853,6 @@
 
 	rxpid = fork();
 	if (rxpid == 0) {
-		iov_buf -= (txmsg_pop - txmsg_start_pop + 1);
 		if (opt->drop_expected || txmsg_ktls_skb_drop)
 			_exit(0);
 
@@ -769,7 +877,7 @@
 				s.bytes_sent, sent_Bps, sent_Bps/giga,
 				s.bytes_recvd, recvd_Bps, recvd_Bps/giga,
 				peek_flag ? "(peek_msg)" : "");
-		if (err && txmsg_cork)
+		if (err && err != -EDATAINTEGRITY && txmsg_cork)
 			err = 0;
 		exit(err ? 1 : 0);
 	} else if (rxpid == -1) {
@@ -1414,8 +1522,8 @@
 
 static void test_send_large(struct sockmap_options *opt, int cgrp)
 {
-	opt->iov_length = 256;
-	opt->iov_count = 1024;
+	opt->iov_length = 8192;
+	opt->iov_count = 32;
 	opt->rate = 2;
 	test_exec(cgrp, opt);
 }
@@ -1536,17 +1644,19 @@
 static void test_txmsg_pull(int cgrp, struct sockmap_options *opt)
 {
 	/* Test basic start/end */
+	txmsg_pass = 1;
 	txmsg_start = 1;
 	txmsg_end = 2;
 	test_send(opt, cgrp);
 
 	/* Test >4k pull */
+	txmsg_pass = 1;
 	txmsg_start = 4096;
 	txmsg_end = 9182;
 	test_send_large(opt, cgrp);
 
 	/* Test pull + redirect */
-	txmsg_redir = 0;
+	txmsg_redir = 1;
 	txmsg_start = 1;
 	txmsg_end = 2;
 	test_send(opt, cgrp);
@@ -1568,12 +1678,16 @@
 
 static void test_txmsg_pop(int cgrp, struct sockmap_options *opt)
 {
+	bool data = opt->data_test;
+
 	/* Test basic pop */
+	txmsg_pass = 1;
 	txmsg_start_pop = 1;
 	txmsg_pop = 2;
 	test_send_many(opt, cgrp);
 
 	/* Test pop with >4k */
+	txmsg_pass = 1;
 	txmsg_start_pop = 4096;
 	txmsg_pop = 4096;
 	test_send_large(opt, cgrp);
@@ -1584,6 +1698,12 @@
 	txmsg_pop = 2;
 	test_send_many(opt, cgrp);
 
+	/* TODO: Test for pop + cork should be different,
+	 * - It makes the layout of the received data difficult
+	 * - It makes it hard to calculate the total_bytes in the recvmsg
+	 * Temporarily skip the data integrity test for this case now.
+	 */
+	opt->data_test = false;
 	/* Test pop + cork */
 	txmsg_redir = 0;
 	txmsg_cork = 512;
@@ -1597,16 +1717,21 @@
 	txmsg_start_pop = 1;
 	txmsg_pop = 2;
 	test_send_many(opt, cgrp);
+	opt->data_test = data;
 }
 
 static void test_txmsg_push(int cgrp, struct sockmap_options *opt)
 {
+	bool data = opt->data_test;
+
 	/* Test basic push */
+	txmsg_pass = 1;
 	txmsg_start_push = 1;
 	txmsg_end_push = 1;
 	test_send(opt, cgrp);
 
 	/* Test push 4kB >4k */
+	txmsg_pass = 1;
 	txmsg_start_push = 4096;
 	txmsg_end_push = 4096;
 	test_send_large(opt, cgrp);
@@ -1617,16 +1742,24 @@
 	txmsg_end_push = 2;
 	test_send_many(opt, cgrp);
 
+	/* TODO: Test for push + cork should be different,
+	 * - It makes the layout of the received data difficult
+	 * - It makes it hard to calculate the total_bytes in the recvmsg
+	 * Temporarily skip the data integrity test for this case now.
+	 */
+	opt->data_test = false;
 	/* Test push + cork */
 	txmsg_redir = 0;
 	txmsg_cork = 512;
 	txmsg_start_push = 1;
 	txmsg_end_push = 2;
 	test_send_many(opt, cgrp);
+	opt->data_test = data;
 }
 
 static void test_txmsg_push_pop(int cgrp, struct sockmap_options *opt)
 {
+	txmsg_pass = 1;
 	txmsg_start_push = 1;
 	txmsg_end_push = 10;
 	txmsg_start_pop = 5;
@@ -1686,6 +1819,19 @@
 	test_exec(cgrp, opt);
 }
 
+static void test_txmsg_ingress_parser2(int cgrp, struct sockmap_options *opt)
+{
+	if (ktls == 1)
+		return;
+	skb_use_parser = 10;
+	opt->iov_length = 20;
+	opt->iov_count = 1;
+	opt->rate = 1;
+	opt->check_recved_len = true;
+	test_exec(cgrp, opt);
+	opt->check_recved_len = false;
+}
+
 char *map_names[] = {
 	"sock_map",
 	"sock_map_txmsg",
@@ -1708,8 +1854,6 @@
 	BPF_SK_MSG_VERDICT,
 	BPF_SK_MSG_VERDICT,
 	BPF_SK_MSG_VERDICT,
-	BPF_SK_MSG_VERDICT,
-	BPF_SK_MSG_VERDICT,
 };
 
 int prog_type[] = {
@@ -1722,8 +1866,6 @@
 	BPF_PROG_TYPE_SK_MSG,
 	BPF_PROG_TYPE_SK_MSG,
 	BPF_PROG_TYPE_SK_MSG,
-	BPF_PROG_TYPE_SK_MSG,
-	BPF_PROG_TYPE_SK_MSG,
 };
 
 static int populate_progs(char *bpf_file)
@@ -1784,7 +1926,8 @@
 	{"txmsg test pull-data", test_txmsg_pull},
 	{"txmsg test pop-data", test_txmsg_pop},
 	{"txmsg test push/pop data", test_txmsg_push_pop},
-	{"txmsg text ingress parser", test_txmsg_ingress_parser},
+	{"txmsg test ingress parser", test_txmsg_ingress_parser},
+	{"txmsg test ingress parser2", test_txmsg_ingress_parser2},
 };
 
 static int check_whitelist(struct _test *t, struct sockmap_options *opt)
@@ -2014,9 +2157,9 @@
 		free(options.whitelist);
 	if (options.blacklist)
 		free(options.blacklist);
+	close(cg_fd);
 	if (cg_created)
 		cleanup_cgroup_environment();
-	close(cg_fd);
 	return err;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_tc_tunnel.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_tc_tunnel.sh
@@ -71,7 +71,6 @@
 server_listen() {
 	ip netns exec "${ns2}" nc "${netcat_opt}" -l "${port}" > "${outfile}" &
 	server_pid=$!
-	sleep 0.2
 }
 
 client_connect() {
@@ -92,6 +91,16 @@
 	fi
 }
 
+wait_for_port() {
+	for i in $(seq 20); do
+		if ip netns exec "${ns2}" ss ${2:--4}OHntl | grep -q "$1"; then
+			return 0
+		fi
+		sleep 0.1
+	done
+	return 1
+}
+
 set -e
 
 # no arguments: automated test, run all
@@ -189,6 +198,7 @@
 # basic communication works
 echo "test basic connectivity"
 server_listen
+wait_for_port ${port} ${netcat_opt}
 client_connect
 verify_data
 
@@ -200,6 +210,7 @@
 	section "encap_${tuntype}_${mac}"
 echo "test bpf encap without decap (expect failure)"
 server_listen
+wait_for_port ${port} ${netcat_opt}
 ! client_connect
 
 if [[ "$tuntype" =~ "udp" ]]; then
@@ -284,6 +295,7 @@
 	client_connect
 	verify_data
 	server_listen
+	wait_for_port ${port} ${netcat_opt}
 fi
 
 # bpf_skb_net_shrink does not take tunnel flags yet, cannot update L3.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_tcp_check_syncookie.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_tcp_check_syncookie.sh
@@ -77,7 +77,7 @@
 MAX_PING_TRIES=5
 BPF_PROG_OBJ="${DIR}/test_tcp_check_syncookie_kern.o"
 CLSACT_SECTION="clsact/check_syncookie"
-XDP_SECTION="xdp/check_syncookie"
+XDP_SECTION="xdp"
 BPF_PROG_ID=0
 PROG="${DIR}/test_tcp_check_syncookie_user"
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_verifier.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_verifier.c
@@ -31,6 +31,7 @@
 #include <linux/if_ether.h>
 #include <linux/btf.h>
 
+#include <bpf/btf.h>
 #include <bpf/bpf.h>
 #include <bpf/libbpf.h>
 
@@ -63,6 +64,11 @@
 static int skips;
 static bool verbose = false;
 
+struct kfunc_btf_id_pair {
+	const char *kfunc;
+	int insn_idx;
+};
+
 struct bpf_test {
 	const char *descr;
 	struct bpf_insn	insns[MAX_INSNS];
@@ -88,6 +94,7 @@
 	int fixup_map_event_output[MAX_FIXUPS];
 	int fixup_map_reuseport_array[MAX_FIXUPS];
 	int fixup_map_ringbuf[MAX_FIXUPS];
+	struct kfunc_btf_id_pair fixup_kfunc_btf_id[MAX_FIXUPS];
 	/* Expected verifier log output for result REJECT or VERBOSE_ACCEPT.
 	 * Can be a tab-separated sequence of expected strings. An empty string
 	 * means no log verification.
@@ -718,6 +725,7 @@
 	int *fixup_map_event_output = test->fixup_map_event_output;
 	int *fixup_map_reuseport_array = test->fixup_map_reuseport_array;
 	int *fixup_map_ringbuf = test->fixup_map_ringbuf;
+	struct kfunc_btf_id_pair *fixup_kfunc_btf_id = test->fixup_kfunc_btf_id;
 
 	if (test->fill_helper) {
 		test->fill_insns = calloc(MAX_TEST_INSNS, sizeof(struct bpf_insn));
@@ -903,6 +911,26 @@
 			fixup_map_ringbuf++;
 		} while (*fixup_map_ringbuf);
 	}
+
+	/* Patch in kfunc BTF IDs */
+	if (fixup_kfunc_btf_id->kfunc) {
+		struct btf *btf;
+		int btf_id;
+
+		do {
+			btf_id = 0;
+			btf = btf__load_vmlinux_btf();
+			if (btf) {
+				btf_id = btf__find_by_name_kind(btf,
+								fixup_kfunc_btf_id->kfunc,
+								BTF_KIND_FUNC);
+				btf_id = btf_id < 0 ? 0 : btf_id;
+			}
+			btf__free(btf);
+			prog[fixup_kfunc_btf_id->insn_idx].imm = btf_id;
+			fixup_kfunc_btf_id++;
+		} while (fixup_kfunc_btf_id->kfunc);
+	}
 }
 
 struct libcap {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_xdp_redirect.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_xdp_redirect.sh
@@ -52,8 +52,8 @@
 		return 0
 	fi
 
-	ip -n ns1 link set veth11 $xdpmode obj xdp_dummy.o sec xdp_dummy &> /dev/null
-	ip -n ns2 link set veth22 $xdpmode obj xdp_dummy.o sec xdp_dummy &> /dev/null
+	ip -n ns1 link set veth11 $xdpmode obj xdp_dummy.o sec xdp &> /dev/null
+	ip -n ns2 link set veth22 $xdpmode obj xdp_dummy.o sec xdp &> /dev/null
 	ip link set dev veth1 $xdpmode obj test_xdp_redirect.o sec redirect_to_222 &> /dev/null
 	ip link set dev veth2 $xdpmode obj test_xdp_redirect.o sec redirect_to_111 &> /dev/null
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_xdp_redirect_multi.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_xdp_redirect_multi.sh
@@ -2,11 +2,11 @@
 # SPDX-License-Identifier: GPL-2.0
 #
 # Test topology:
-#     - - - - - - - - - - - - - - - - - - - - - - - - -
-#    | veth1         veth2         veth3 |  ... init net
+#    - - - - - - - - - - - - - - - - - - -
+#    | veth1         veth2         veth3 |  ns0
 #     - -| - - - - - - | - - - - - - | - -
 #    ---------     ---------     ---------
-#    | veth0 |     | veth0 |     | veth0 |  ...
+#    | veth0 |     | veth0 |     | veth0 |
 #    ---------     ---------     ---------
 #       ns1           ns2           ns3
 #
@@ -31,6 +31,12 @@
 DRV_MODE="xdpgeneric xdpdrv xdpegress"
 PASS=0
 FAIL=0
+LOG_DIR=$(mktemp -d)
+declare -a NS
+NS[0]="ns0-$(mktemp -u XXXXXX)"
+NS[1]="ns1-$(mktemp -u XXXXXX)"
+NS[2]="ns2-$(mktemp -u XXXXXX)"
+NS[3]="ns3-$(mktemp -u XXXXXX)"
 
 test_pass()
 {
@@ -46,9 +52,8 @@
 
 clean_up()
 {
-	for i in $(seq $NUM); do
-		ip link del veth$i 2> /dev/null
-		ip netns del ns$i 2> /dev/null
+	for i in $(seq 0 $NUM); do
+		ip netns del ${NS[$i]} 2> /dev/null
 	done
 }
 
@@ -77,21 +82,22 @@
 		mode="xdpdrv"
 	fi
 
+	ip netns add ${NS[0]}
 	for i in $(seq $NUM); do
-	        ip netns add ns$i
-	        ip link add veth$i type veth peer name veth0 netns ns$i
-		ip link set veth$i up
-		ip -n ns$i link set veth0 up
+	        ip netns add ${NS[$i]}
+		ip -n ${NS[$i]} link add veth0 type veth peer name veth$i netns ${NS[0]}
+		ip -n ${NS[$i]} link set veth0 up
+		ip -n ${NS[0]} link set veth$i up
 
-		ip -n ns$i addr add 192.0.2.$i/24 dev veth0
-		ip -n ns$i addr add 2001:db8::$i/64 dev veth0
+		ip -n ${NS[$i]} addr add 192.0.2.$i/24 dev veth0
+		ip -n ${NS[$i]} addr add 2001:db8::$i/64 dev veth0
 		# Add a neigh entry for IPv4 ping test
-		ip -n ns$i neigh add 192.0.2.253 lladdr 00:00:00:00:00:01 dev veth0
-		ip -n ns$i link set veth0 $mode obj \
-			xdp_dummy.o sec xdp_dummy &> /dev/null || \
+		ip -n ${NS[$i]} neigh add 192.0.2.253 lladdr 00:00:00:00:00:01 dev veth0
+		ip -n ${NS[$i]} link set veth0 $mode obj \
+			xdp_dummy.o sec xdp &> /dev/null || \
 			{ test_fail "Unable to load dummy xdp" && exit 1; }
 		IFACES="$IFACES veth$i"
-		veth_mac[$i]=$(ip link show veth$i | awk '/link\/ether/ {print $2}')
+		veth_mac[$i]=$(ip -n ${NS[0]} link show veth$i | awk '/link\/ether/ {print $2}')
 	done
 }
 
@@ -100,17 +106,17 @@
 	local mode=$1
 
 	# mac test
-	ip netns exec ns2 tcpdump -e -i veth0 -nn -l -e &> mac_ns1-2_${mode}.log &
-	ip netns exec ns3 tcpdump -e -i veth0 -nn -l -e &> mac_ns1-3_${mode}.log &
+	ip netns exec ${NS[2]} tcpdump -e -i veth0 -nn -l -e &> ${LOG_DIR}/mac_ns1-2_${mode}.log &
+	ip netns exec ${NS[3]} tcpdump -e -i veth0 -nn -l -e &> ${LOG_DIR}/mac_ns1-3_${mode}.log &
 	sleep 0.5
-	ip netns exec ns1 ping 192.0.2.254 -i 0.1 -c 4 &> /dev/null
+	ip netns exec ${NS[1]} ping 192.0.2.254 -i 0.1 -c 4 &> /dev/null
 	sleep 0.5
-	pkill -9 tcpdump
+	pkill tcpdump
 
 	# mac check
-	grep -q "${veth_mac[2]} > ff:ff:ff:ff:ff:ff" mac_ns1-2_${mode}.log && \
+	grep -q "${veth_mac[2]} > ff:ff:ff:ff:ff:ff" ${LOG_DIR}/mac_ns1-2_${mode}.log && \
 	       test_pass "$mode mac ns1-2" || test_fail "$mode mac ns1-2"
-	grep -q "${veth_mac[3]} > ff:ff:ff:ff:ff:ff" mac_ns1-3_${mode}.log && \
+	grep -q "${veth_mac[3]} > ff:ff:ff:ff:ff:ff" ${LOG_DIR}/mac_ns1-3_${mode}.log && \
 		test_pass "$mode mac ns1-3" || test_fail "$mode mac ns1-3"
 }
 
@@ -119,48 +125,48 @@
 	local mode=$1
 
 	# ping6 test: echo request should be redirect back to itself, not others
-	ip netns exec ns1 ip neigh add 2001:db8::2 dev veth0 lladdr 00:00:00:00:00:02
+	ip netns exec ${NS[1]} ip neigh add 2001:db8::2 dev veth0 lladdr 00:00:00:00:00:02
 
-	ip netns exec ns1 tcpdump -i veth0 -nn -l -e &> ns1-1_${mode}.log &
-	ip netns exec ns2 tcpdump -i veth0 -nn -l -e &> ns1-2_${mode}.log &
-	ip netns exec ns3 tcpdump -i veth0 -nn -l -e &> ns1-3_${mode}.log &
+	ip netns exec ${NS[1]} tcpdump -i veth0 -nn -l -e &> ${LOG_DIR}/ns1-1_${mode}.log &
+	ip netns exec ${NS[2]} tcpdump -i veth0 -nn -l -e &> ${LOG_DIR}/ns1-2_${mode}.log &
+	ip netns exec ${NS[3]} tcpdump -i veth0 -nn -l -e &> ${LOG_DIR}/ns1-3_${mode}.log &
 	sleep 0.5
 	# ARP test
-	ip netns exec ns1 ping 192.0.2.254 -i 0.1 -c 4 &> /dev/null
+	ip netns exec ${NS[1]} arping -q -c 2 -I veth0 192.0.2.254
 	# IPv4 test
-	ip netns exec ns1 ping 192.0.2.253 -i 0.1 -c 4 &> /dev/null
+	ip netns exec ${NS[1]} ping 192.0.2.253 -i 0.1 -c 4 &> /dev/null
 	# IPv6 test
-	ip netns exec ns1 ping6 2001:db8::2 -i 0.1 -c 2 &> /dev/null
+	ip netns exec ${NS[1]} ping6 2001:db8::2 -i 0.1 -c 2 &> /dev/null
 	sleep 0.5
-	pkill -9 tcpdump
+	pkill tcpdump
 
 	# All netns should receive the redirect arp requests
-	[ $(grep -c "who-has 192.0.2.254" ns1-1_${mode}.log) -gt 4 ] && \
+	[ $(grep -cF "who-has 192.0.2.254" ${LOG_DIR}/ns1-1_${mode}.log) -eq 4 ] && \
 		test_pass "$mode arp(F_BROADCAST) ns1-1" || \
 		test_fail "$mode arp(F_BROADCAST) ns1-1"
-	[ $(grep -c "who-has 192.0.2.254" ns1-2_${mode}.log) -le 4 ] && \
+	[ $(grep -cF "who-has 192.0.2.254" ${LOG_DIR}/ns1-2_${mode}.log) -eq 2 ] && \
 		test_pass "$mode arp(F_BROADCAST) ns1-2" || \
 		test_fail "$mode arp(F_BROADCAST) ns1-2"
-	[ $(grep -c "who-has 192.0.2.254" ns1-3_${mode}.log) -le 4 ] && \
+	[ $(grep -cF "who-has 192.0.2.254" ${LOG_DIR}/ns1-3_${mode}.log) -eq 2 ] && \
 		test_pass "$mode arp(F_BROADCAST) ns1-3" || \
 		test_fail "$mode arp(F_BROADCAST) ns1-3"
 
 	# ns1 should not receive the redirect echo request, others should
-	[ $(grep -c "ICMP echo request" ns1-1_${mode}.log) -eq 4 ] && \
+	[ $(grep -c "ICMP echo request" ${LOG_DIR}/ns1-1_${mode}.log) -eq 4 ] && \
 		test_pass "$mode IPv4 (F_BROADCAST|F_EXCLUDE_INGRESS) ns1-1" || \
 		test_fail "$mode IPv4 (F_BROADCAST|F_EXCLUDE_INGRESS) ns1-1"
-	[ $(grep -c "ICMP echo request" ns1-2_${mode}.log) -eq 4 ] && \
+	[ $(grep -c "ICMP echo request" ${LOG_DIR}/ns1-2_${mode}.log) -eq 4 ] && \
 		test_pass "$mode IPv4 (F_BROADCAST|F_EXCLUDE_INGRESS) ns1-2" || \
 		test_fail "$mode IPv4 (F_BROADCAST|F_EXCLUDE_INGRESS) ns1-2"
-	[ $(grep -c "ICMP echo request" ns1-3_${mode}.log) -eq 4 ] && \
+	[ $(grep -c "ICMP echo request" ${LOG_DIR}/ns1-3_${mode}.log) -eq 4 ] && \
 		test_pass "$mode IPv4 (F_BROADCAST|F_EXCLUDE_INGRESS) ns1-3" || \
 		test_fail "$mode IPv4 (F_BROADCAST|F_EXCLUDE_INGRESS) ns1-3"
 
 	# ns1 should receive the echo request, ns2 should not
-	[ $(grep -c "ICMP6, echo request" ns1-1_${mode}.log) -eq 4 ] && \
+	[ $(grep -c "ICMP6, echo request" ${LOG_DIR}/ns1-1_${mode}.log) -eq 4 ] && \
 		test_pass "$mode IPv6 (no flags) ns1-1" || \
 		test_fail "$mode IPv6 (no flags) ns1-1"
-	[ $(grep -c "ICMP6, echo request" ns1-2_${mode}.log) -eq 0 ] && \
+	[ $(grep -c "ICMP6, echo request" ${LOG_DIR}/ns1-2_${mode}.log) -eq 0 ] && \
 		test_pass "$mode IPv6 (no flags) ns1-2" || \
 		test_fail "$mode IPv6 (no flags) ns1-2"
 }
@@ -176,9 +182,13 @@
 		xdpgeneric) drv_p="-S";;
 	esac
 
-	./xdp_redirect_multi $drv_p $IFACES &> xdp_redirect_${mode}.log &
+	ip netns exec ${NS[0]} ./xdp_redirect_multi $drv_p $IFACES &> ${LOG_DIR}/xdp_redirect_${mode}.log &
 	xdp_pid=$!
 	sleep 1
+	if ! ps -p $xdp_pid > /dev/null; then
+		test_fail "$mode xdp_redirect_multi start failed"
+		return 1
+	fi
 
 	if [ "$mode" = "xdpegress" ]; then
 		do_egress_tests $mode
@@ -189,16 +199,16 @@
 	kill $xdp_pid
 }
 
-trap clean_up 0 2 3 6 9
-
 check_env
-rm -f xdp_redirect_*.log ns*.log mac_ns*.log
+
+trap clean_up EXIT
 
 for mode in ${DRV_MODE}; do
 	setup_ns $mode
 	do_tests $mode
 	clean_up
 done
+rm -rf ${LOG_DIR}
 
 echo "Summary: PASS $PASS, FAIL $FAIL"
 [ $FAIL -eq 0 ] && exit 0 || exit 1
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_xdp_veth.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_xdp_veth.sh
@@ -107,9 +107,9 @@
 ip link set dev veth2 xdp pinned $BPF_DIR/progs/redirect_map_1
 ip link set dev veth3 xdp pinned $BPF_DIR/progs/redirect_map_2
 
-ip -n ns1 link set dev veth11 xdp obj xdp_dummy.o sec xdp_dummy
+ip -n ns1 link set dev veth11 xdp obj xdp_dummy.o sec xdp
 ip -n ns2 link set dev veth22 xdp obj xdp_tx.o sec xdp
-ip -n ns3 link set dev veth33 xdp obj xdp_dummy.o sec xdp_dummy
+ip -n ns3 link set dev veth33 xdp obj xdp_dummy.o sec xdp
 
 trap cleanup EXIT
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/test_xsk.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/test_xsk.sh
@@ -106,6 +106,7 @@
 	ip link add ${VETH0} numtxqueues 4 numrxqueues 4 type veth peer name ${VETH1} numtxqueues 4 numrxqueues 4
 	if [ -f /proc/net/if_inet6 ]; then
 		echo 1 > /proc/sys/net/ipv6/conf/${VETH0}/disable_ipv6
+		echo 1 > /proc/sys/net/ipv6/conf/${VETH1}/disable_ipv6
 	fi
 	if [[ $verbose -eq 1 ]]; then
 	        echo "setting up ${VETH1}: namespace: ${NS1}"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/array_access.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/array_access.c
@@ -186,7 +186,7 @@
 	},
 	.fixup_map_hash_48b = { 3 },
 	.errstr_unpriv = "R0 leaks addr",
-	.errstr = "R0 unbounded memory access",
+	.errstr = "invalid access to map value, value_size=48 off=44 size=8",
 	.result_unpriv = REJECT,
 	.result = REJECT,
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/atomic_cmpxchg.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/atomic_cmpxchg.c
@@ -71,6 +71,8 @@
 		BPF_EXIT_INSN(),
 	},
 	.result = ACCEPT,
+	.result_unpriv = REJECT,
+	.errstr_unpriv = "R0 leaks addr into mem",
 },
 {
 	"Can't use cmpxchg on uninit src reg",
@@ -118,4 +120,88 @@
 		BPF_EXIT_INSN(),
 	},
 	.result = ACCEPT,
+	.result_unpriv = REJECT,
+	.errstr_unpriv = "R0 leaks addr into mem",
+},
+{
+	"Dest pointer in r0 - succeed, check 2",
+	.insns = {
+		/* r0 = &val */
+		BPF_MOV64_REG(BPF_REG_0, BPF_REG_10),
+		/* val = r0; */
+		BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -8),
+		/* r5 = &val */
+		BPF_MOV64_REG(BPF_REG_5, BPF_REG_10),
+		/* r0 = atomic_cmpxchg(&val, r0, r5); */
+		BPF_ATOMIC_OP(BPF_DW, BPF_CMPXCHG, BPF_REG_10, BPF_REG_5, -8),
+		/* r1 = *r0 */
+		BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_0, -8),
+		/* exit(0); */
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+		BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.result_unpriv = REJECT,
+	.errstr_unpriv = "R0 leaks addr into mem",
+},
+{
+	"Dest pointer in r0 - succeed, check 3",
+	.insns = {
+		/* r0 = &val */
+		BPF_MOV64_REG(BPF_REG_0, BPF_REG_10),
+		/* val = r0; */
+		BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -8),
+		/* r5 = &val */
+		BPF_MOV64_REG(BPF_REG_5, BPF_REG_10),
+		/* r0 = atomic_cmpxchg(&val, r0, r5); */
+		BPF_ATOMIC_OP(BPF_W, BPF_CMPXCHG, BPF_REG_10, BPF_REG_5, -8),
+		/* exit(0); */
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+		BPF_EXIT_INSN(),
+	},
+	.result = REJECT,
+	.errstr = "invalid size of register fill",
+	.errstr_unpriv = "R0 leaks addr into mem",
+},
+{
+	"Dest pointer in r0 - succeed, check 4",
+	.insns = {
+		/* r0 = &val */
+		BPF_MOV32_REG(BPF_REG_0, BPF_REG_10),
+		/* val = r0; */
+		BPF_STX_MEM(BPF_W, BPF_REG_10, BPF_REG_0, -8),
+		/* r5 = &val */
+		BPF_MOV32_REG(BPF_REG_5, BPF_REG_10),
+		/* r0 = atomic_cmpxchg(&val, r0, r5); */
+		BPF_ATOMIC_OP(BPF_W, BPF_CMPXCHG, BPF_REG_10, BPF_REG_5, -8),
+		/* r1 = *r10 */
+		BPF_LDX_MEM(BPF_W, BPF_REG_1, BPF_REG_10, -8),
+		/* exit(0); */
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+		BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.result_unpriv = REJECT,
+	.errstr_unpriv = "R10 partial copy of pointer",
+},
+{
+	"Dest pointer in r0 - succeed, check 5",
+	.insns = {
+		/* r0 = &val */
+		BPF_MOV32_REG(BPF_REG_0, BPF_REG_10),
+		/* val = r0; */
+		BPF_STX_MEM(BPF_W, BPF_REG_10, BPF_REG_0, -8),
+		/* r5 = &val */
+		BPF_MOV32_REG(BPF_REG_5, BPF_REG_10),
+		/* r0 = atomic_cmpxchg(&val, r0, r5); */
+		BPF_ATOMIC_OP(BPF_W, BPF_CMPXCHG, BPF_REG_10, BPF_REG_5, -8),
+		/* r1 = *r0 */
+		BPF_LDX_MEM(BPF_W, BPF_REG_1, BPF_REG_0, -8),
+		/* exit(0); */
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+		BPF_EXIT_INSN(),
+	},
+	.result = REJECT,
+	.errstr = "R0 invalid mem access",
+	.errstr_unpriv = "R10 partial copy of pointer",
 },
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/bounds_mix_sign_unsign.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/bounds_mix_sign_unsign.c
@@ -1,13 +1,14 @@
 {
 	"bounds checks mixing signed and unsigned, positive bounds",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 7),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 6),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, 2),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_2, BPF_REG_1, 3),
@@ -17,20 +18,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 7),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 6),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_2, 3),
@@ -40,20 +42,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 2",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_2, 5),
@@ -65,20 +68,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 3",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 7),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_2, 4),
@@ -89,20 +93,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 4",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 7),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 6),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, 1),
 	BPF_ALU64_REG(BPF_AND, BPF_REG_1, BPF_REG_2),
@@ -112,19 +117,20 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.result = ACCEPT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 5",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_2, 5),
@@ -135,17 +141,20 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 6",
 	.insns = {
+	BPF_MOV64_REG(BPF_REG_9, BPF_REG_1),
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_9),
 	BPF_MOV64_IMM(BPF_REG_2, 0),
 	BPF_MOV64_REG(BPF_REG_3, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_3, -512),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_4, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_6, -1),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_4, BPF_REG_6, 5),
@@ -163,13 +172,14 @@
 {
 	"bounds checks mixing signed and unsigned, variant 7",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 7),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 6),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, 1024 * 1024 * 1024),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_2, 3),
@@ -179,19 +189,20 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.result = ACCEPT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 8",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_2, BPF_REG_1, 2),
@@ -203,20 +214,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 9",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 10),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_LD_IMM64(BPF_REG_2, -9223372036854775808ULL),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_2, BPF_REG_1, 2),
@@ -228,19 +240,20 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.result = ACCEPT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 10",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, 0),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_2, BPF_REG_1, 2),
@@ -252,20 +265,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 11",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_2, BPF_REG_1, 2),
@@ -278,20 +292,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 12",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 9),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -6),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_2, BPF_REG_1, 2),
@@ -303,20 +318,21 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 13",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 6),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 5),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, 2),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_2, BPF_REG_1, 2),
@@ -331,7 +347,7 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
@@ -340,13 +356,14 @@
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_9, BPF_REG_1,
 		    offsetof(struct __sk_buff, mark)),
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 8),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 7),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -1),
 	BPF_MOV64_IMM(BPF_REG_8, 2),
@@ -360,20 +377,21 @@
 	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_2, -3),
 	BPF_JMP_IMM(BPF_JA, 0, 0, -7),
 	},
-	.fixup_map_hash_8b = { 4 },
+	.fixup_map_hash_8b = { 6 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
 {
 	"bounds checks mixing signed and unsigned, variant 15",
 	.insns = {
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_STX_MEM(BPF_DW, BPF_REG_10, BPF_REG_0, -16),
 	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
 	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
 	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
 	BPF_LD_MAP_FD(BPF_REG_1, 0),
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
-	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 4),
-	BPF_ST_MEM(BPF_DW, BPF_REG_10, -16, -8),
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 3),
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_10, -16),
 	BPF_MOV64_IMM(BPF_REG_2, -6),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_2, BPF_REG_1, 2),
@@ -387,7 +405,7 @@
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
-	.fixup_map_hash_8b = { 3 },
+	.fixup_map_hash_8b = { 5 },
 	.errstr = "unbounded min value",
 	.result = REJECT,
 },
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/calls.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/calls.c
@@ -108,6 +108,25 @@
 	.errstr = "R0 min value is outside of the allowed memory range",
 },
 {
+	"calls: trigger reg2btf_ids[reg->type] for reg->type > __BPF_REG_TYPE_MAX",
+	.insns = {
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_10),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, -8),
+	BPF_ST_MEM(BPF_DW, BPF_REG_1, 0, 0),
+	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, BPF_PSEUDO_KFUNC_CALL, 0, 0),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_0),
+	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, BPF_PSEUDO_KFUNC_CALL, 0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.prog_type = BPF_PROG_TYPE_SCHED_CLS,
+	.result = REJECT,
+	.errstr = "arg#0 pointer type STRUCT prog_test_ref_kfunc must point",
+	.fixup_kfunc_btf_id = {
+		{ "bpf_kfunc_call_test_acquire", 3 },
+		{ "bpf_kfunc_call_test_release", 5 },
+	},
+},
+{
 	"calls: overlapping caller/callee",
 	.insns = {
 	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 1, 0, 0),
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/ref_tracking.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/ref_tracking.c
@@ -905,3 +905,39 @@
 	.result_unpriv = REJECT,
 	.errstr_unpriv = "unknown func",
 },
+{
+	"reference tracking: try to leak released ptr reg",
+	.insns = {
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+		BPF_STX_MEM(BPF_W, BPF_REG_10, BPF_REG_0, -4),
+		BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
+		BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -4),
+		BPF_LD_MAP_FD(BPF_REG_1, 0),
+		BPF_EMIT_CALL(BPF_FUNC_map_lookup_elem),
+		BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 1),
+		BPF_EXIT_INSN(),
+		BPF_MOV64_REG(BPF_REG_9, BPF_REG_0),
+
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+		BPF_LD_MAP_FD(BPF_REG_1, 0),
+		BPF_MOV64_IMM(BPF_REG_2, 8),
+		BPF_MOV64_IMM(BPF_REG_3, 0),
+		BPF_EMIT_CALL(BPF_FUNC_ringbuf_reserve),
+		BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 1),
+		BPF_EXIT_INSN(),
+		BPF_MOV64_REG(BPF_REG_8, BPF_REG_0),
+
+		BPF_MOV64_REG(BPF_REG_1, BPF_REG_8),
+		BPF_MOV64_IMM(BPF_REG_2, 0),
+		BPF_EMIT_CALL(BPF_FUNC_ringbuf_discard),
+		BPF_MOV64_IMM(BPF_REG_0, 0),
+
+		BPF_STX_MEM(BPF_DW, BPF_REG_9, BPF_REG_8, 0),
+		BPF_EXIT_INSN()
+	},
+	.fixup_map_array_48b = { 4 },
+	.fixup_map_ringbuf = { 11 },
+	.result = ACCEPT,
+	.result_unpriv = REJECT,
+	.errstr_unpriv = "R8 !read_ok"
+},
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/search_pruning.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/search_pruning.c
@@ -154,3 +154,39 @@
 	.result_unpriv = ACCEPT,
 	.insn_processed = 15,
 },
+/* The test performs a conditional 64-bit write to a stack location
+ * fp[-8], this is followed by an unconditional 8-bit write to fp[-8],
+ * then data is read from fp[-8]. This sequence is unsafe.
+ *
+ * The test would be mistakenly marked as safe w/o dst register parent
+ * preservation in verifier.c:copy_register_state() function.
+ *
+ * Note the usage of BPF_F_TEST_STATE_FREQ to force creation of the
+ * checkpoint state after conditional 64-bit assignment.
+ */
+{
+	"write tracking and register parent chain bug",
+	.insns = {
+	/* r6 = ktime_get_ns() */
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	BPF_MOV64_REG(BPF_REG_6, BPF_REG_0),
+	/* r0 = ktime_get_ns() */
+	BPF_EMIT_CALL(BPF_FUNC_ktime_get_ns),
+	/* if r0 > r6 goto +1 */
+	BPF_JMP_REG(BPF_JGT, BPF_REG_0, BPF_REG_6, 1),
+	/* *(u64 *)(r10 - 8) = 0xdeadbeef */
+	BPF_ST_MEM(BPF_DW, BPF_REG_FP, -8, 0xdeadbeef),
+	/* r1 = 42 */
+	BPF_MOV64_IMM(BPF_REG_1, 42),
+	/* *(u8 *)(r10 - 8) = r1 */
+	BPF_STX_MEM(BPF_B, BPF_REG_FP, BPF_REG_1, -8),
+	/* r2 = *(u64 *)(r10 - 8) */
+	BPF_LDX_MEM(BPF_DW, BPF_REG_2, BPF_REG_FP, -8),
+	/* exit(0) */
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.flags = BPF_F_TEST_STATE_FREQ,
+	.errstr = "invalid read from stack off -8+1 size 8",
+	.result = REJECT,
+},
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/sock.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/sock.c
@@ -121,7 +121,25 @@
 	.result = ACCEPT,
 },
 {
-	"sk_fullsock(skb->sk): sk->dst_port [narrow load]",
+	"sk_fullsock(skb->sk): sk->dst_port [word load] (backward compatibility)",
+	.insns = {
+	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_1, offsetof(struct __sk_buff, sk)),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_1, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_EMIT_CALL(BPF_FUNC_sk_fullsock),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_LDX_MEM(BPF_W, BPF_REG_0, BPF_REG_0, offsetof(struct bpf_sock, dst_port)),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.prog_type = BPF_PROG_TYPE_CGROUP_SKB,
+	.result = ACCEPT,
+},
+{
+	"sk_fullsock(skb->sk): sk->dst_port [half load]",
 	.insns = {
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_1, offsetof(struct __sk_buff, sk)),
 	BPF_JMP_IMM(BPF_JNE, BPF_REG_1, 0, 2),
@@ -139,7 +157,64 @@
 	.result = ACCEPT,
 },
 {
-	"sk_fullsock(skb->sk): sk->dst_port [load 2nd byte]",
+	"sk_fullsock(skb->sk): sk->dst_port [half load] (invalid)",
+	.insns = {
+	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_1, offsetof(struct __sk_buff, sk)),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_1, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_EMIT_CALL(BPF_FUNC_sk_fullsock),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_LDX_MEM(BPF_H, BPF_REG_0, BPF_REG_0, offsetof(struct bpf_sock, dst_port) + 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.prog_type = BPF_PROG_TYPE_CGROUP_SKB,
+	.result = REJECT,
+	.errstr = "invalid sock access",
+},
+{
+	"sk_fullsock(skb->sk): sk->dst_port [byte load]",
+	.insns = {
+	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_1, offsetof(struct __sk_buff, sk)),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_1, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_EMIT_CALL(BPF_FUNC_sk_fullsock),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_LDX_MEM(BPF_B, BPF_REG_2, BPF_REG_0, offsetof(struct bpf_sock, dst_port)),
+	BPF_LDX_MEM(BPF_B, BPF_REG_2, BPF_REG_0, offsetof(struct bpf_sock, dst_port) + 1),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.prog_type = BPF_PROG_TYPE_CGROUP_SKB,
+	.result = ACCEPT,
+},
+{
+	"sk_fullsock(skb->sk): sk->dst_port [byte load] (invalid)",
+	.insns = {
+	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_1, offsetof(struct __sk_buff, sk)),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_1, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_EMIT_CALL(BPF_FUNC_sk_fullsock),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	BPF_LDX_MEM(BPF_B, BPF_REG_0, BPF_REG_0, offsetof(struct bpf_sock, dst_port) + 2),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.prog_type = BPF_PROG_TYPE_CGROUP_SKB,
+	.result = REJECT,
+	.errstr = "invalid sock access",
+},
+{
+	"sk_fullsock(skb->sk): past sk->dst_port [half load] (invalid)",
 	.insns = {
 	BPF_LDX_MEM(BPF_DW, BPF_REG_1, BPF_REG_1, offsetof(struct __sk_buff, sk)),
 	BPF_JMP_IMM(BPF_JNE, BPF_REG_1, 0, 2),
@@ -149,7 +224,7 @@
 	BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 2),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
-	BPF_LDX_MEM(BPF_B, BPF_REG_0, BPF_REG_0, offsetof(struct bpf_sock, dst_port) + 1),
+	BPF_LDX_MEM(BPF_H, BPF_REG_0, BPF_REG_0, offsetofend(struct bpf_sock, dst_port)),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/spill_fill.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/spill_fill.c
@@ -59,6 +59,34 @@
 	.result_unpriv = ACCEPT,
 },
 {
+	"check with invalid reg offset 0",
+	.insns = {
+	/* reserve 8 byte ringbuf memory */
+	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
+	BPF_LD_MAP_FD(BPF_REG_1, 0),
+	BPF_MOV64_IMM(BPF_REG_2, 8),
+	BPF_MOV64_IMM(BPF_REG_3, 0),
+	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_ringbuf_reserve),
+	/* store a pointer to the reserved memory in R6 */
+	BPF_MOV64_REG(BPF_REG_6, BPF_REG_0),
+	/* add invalid offset to memory or NULL */
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_0, 1),
+	/* check whether the reservation was successful */
+	BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 4),
+	/* should not be able to access *(R7) = 0 */
+	BPF_ST_MEM(BPF_W, BPF_REG_6, 0, 0),
+	/* submit the reserved ringbuf memory */
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_6),
+	BPF_MOV64_IMM(BPF_REG_2, 0),
+	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_ringbuf_submit),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.fixup_map_ringbuf = { 1 },
+	.result = REJECT,
+	.errstr = "R0 pointer arithmetic on mem_or_null prohibited",
+},
+{
 	"check corrupted spill/fill",
 	.insns = {
 	/* spill R1(ctx) into stack */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/value_ptr_arith.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/value_ptr_arith.c
@@ -1078,6 +1078,29 @@
 	.errstr_unpriv = "R0 pointer -= pointer prohibited",
 },
 {
+	"map access: trying to leak tained dst reg",
+	.insns = {
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
+	BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
+	BPF_LD_MAP_FD(BPF_REG_1, 0),
+	BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_map_lookup_elem),
+	BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 1),
+	BPF_EXIT_INSN(),
+	BPF_MOV64_REG(BPF_REG_2, BPF_REG_0),
+	BPF_MOV32_IMM(BPF_REG_1, 0xFFFFFFFF),
+	BPF_MOV32_REG(BPF_REG_1, BPF_REG_1),
+	BPF_ALU64_REG(BPF_SUB, BPF_REG_2, BPF_REG_1),
+	BPF_STX_MEM(BPF_DW, BPF_REG_0, BPF_REG_2, 0),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.fixup_map_array_48b = { 4 },
+	.result = REJECT,
+	.errstr = "math between map_value pointer and 4294967295 is not allowed",
+},
+{
 	"32bit pkt_ptr -= scalar",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_8, BPF_REG_1,
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/verifier/xdp_direct_packet_access.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/verifier/xdp_direct_packet_access.c
@@ -35,7 +35,7 @@
 	.prog_type = BPF_PROG_TYPE_XDP,
 },
 {
-	"XDP pkt read, pkt_data' > pkt_end, good access",
+	"XDP pkt read, pkt_data' > pkt_end, corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
@@ -88,6 +88,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_data' > pkt_end, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data' > pkt_end, corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_end > pkt_data', good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
@@ -106,16 +141,16 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_end > pkt_data', bad access 1",
+	"XDP pkt read, pkt_end > pkt_data', corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
 		    offsetof(struct xdp_md, data_end)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_3, BPF_REG_1, 1),
 	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -143,6 +178,42 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_end > pkt_data', corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_end > pkt_data', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_data' < pkt_end, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
@@ -161,16 +232,16 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data' < pkt_end, bad access 1",
+	"XDP pkt read, pkt_data' < pkt_end, corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
 		    offsetof(struct xdp_md, data_end)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JLT, BPF_REG_1, BPF_REG_3, 1),
 	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -198,7 +269,43 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_end < pkt_data', good access",
+	"XDP pkt read, pkt_data' < pkt_end, corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data' < pkt_end, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_end < pkt_data', corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
@@ -251,6 +358,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_end < pkt_data', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_end < pkt_data', corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_data' >= pkt_end, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
@@ -268,15 +410,15 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data' >= pkt_end, bad access 1",
+	"XDP pkt read, pkt_data' >= pkt_end, corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
 		    offsetof(struct xdp_md, data_end)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_1, BPF_REG_3, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -304,7 +446,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_end >= pkt_data', good access",
+	"XDP pkt read, pkt_data' >= pkt_end, corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data' >= pkt_end, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_end >= pkt_data', corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
@@ -359,7 +535,44 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data' <= pkt_end, good access",
+	"XDP pkt read, pkt_end >= pkt_data', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_end >= pkt_data', corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data' <= pkt_end, corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
@@ -414,6 +627,43 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_data' <= pkt_end, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data' <= pkt_end, corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_end <= pkt_data', good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
@@ -431,15 +681,15 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_end <= pkt_data', bad access 1",
+	"XDP pkt read, pkt_end <= pkt_data', corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
 		    offsetof(struct xdp_md, data_end)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JLE, BPF_REG_3, BPF_REG_1, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -467,7 +717,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_meta' > pkt_data, good access",
+	"XDP pkt read, pkt_end <= pkt_data', corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_end <= pkt_data', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1,
+		    offsetof(struct xdp_md, data_end)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_meta' > pkt_data, corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
@@ -520,6 +804,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_meta' > pkt_data, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_meta' > pkt_data, corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_data > pkt_meta', good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
@@ -538,16 +857,16 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data > pkt_meta', bad access 1",
+	"XDP pkt read, pkt_data > pkt_meta', corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JGT, BPF_REG_3, BPF_REG_1, 1),
 	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -575,6 +894,42 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_data > pkt_meta', corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data > pkt_meta', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JGT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_meta' < pkt_data, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
@@ -593,16 +948,16 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_meta' < pkt_data, bad access 1",
+	"XDP pkt read, pkt_meta' < pkt_data, corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JLT, BPF_REG_1, BPF_REG_3, 1),
 	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -630,7 +985,43 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data < pkt_meta', good access",
+	"XDP pkt read, pkt_meta' < pkt_data, corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_meta' < pkt_data, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data < pkt_meta', corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
@@ -683,6 +1074,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_data < pkt_meta', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data < pkt_meta', corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLT, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_meta' >= pkt_data, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
@@ -700,15 +1126,15 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_meta' >= pkt_data, bad access 1",
+	"XDP pkt read, pkt_meta' >= pkt_data, corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JGE, BPF_REG_1, BPF_REG_3, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -736,7 +1162,41 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data >= pkt_meta', good access",
+	"XDP pkt read, pkt_meta' >= pkt_data, corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_meta' >= pkt_data, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data >= pkt_meta', corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
@@ -791,7 +1251,44 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_meta' <= pkt_data, good access",
+	"XDP pkt read, pkt_data >= pkt_meta', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data >= pkt_meta', corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JGE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_meta' <= pkt_data, corner case, good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
@@ -846,6 +1343,43 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
+	"XDP pkt read, pkt_meta' <= pkt_data, corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 9),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -9),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_meta' <= pkt_data, corner case -1, bad access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_1, BPF_REG_3, 1),
+	BPF_JMP_IMM(BPF_JA, 0, 0, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.errstr = "R1 offset is outside of the packet",
+	.result = REJECT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
 	"XDP pkt read, pkt_data <= pkt_meta', good access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
@@ -863,15 +1397,15 @@
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
 {
-	"XDP pkt read, pkt_data <= pkt_meta', bad access 1",
+	"XDP pkt read, pkt_data <= pkt_meta', corner case -1, bad access",
 	.insns = {
 	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
 		    offsetof(struct xdp_md, data_meta)),
 	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
 	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
-	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 6),
 	BPF_JMP_REG(BPF_JLE, BPF_REG_3, BPF_REG_1, 1),
-	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -6),
 	BPF_MOV64_IMM(BPF_REG_0, 0),
 	BPF_EXIT_INSN(),
 	},
@@ -898,3 +1432,37 @@
 	.prog_type = BPF_PROG_TYPE_XDP,
 	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
 },
+{
+	"XDP pkt read, pkt_data <= pkt_meta', corner case, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 7),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -7),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
+{
+	"XDP pkt read, pkt_data <= pkt_meta', corner case +1, good access",
+	.insns = {
+	BPF_LDX_MEM(BPF_W, BPF_REG_2, BPF_REG_1,
+		    offsetof(struct xdp_md, data_meta)),
+	BPF_LDX_MEM(BPF_W, BPF_REG_3, BPF_REG_1, offsetof(struct xdp_md, data)),
+	BPF_MOV64_REG(BPF_REG_1, BPF_REG_2),
+	BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, 8),
+	BPF_JMP_REG(BPF_JLE, BPF_REG_3, BPF_REG_1, 1),
+	BPF_LDX_MEM(BPF_DW, BPF_REG_0, BPF_REG_1, -8),
+	BPF_MOV64_IMM(BPF_REG_0, 0),
+	BPF_EXIT_INSN(),
+	},
+	.result = ACCEPT,
+	.prog_type = BPF_PROG_TYPE_XDP,
+	.flags = F_NEEDS_EFFICIENT_UNALIGNED_ACCESS,
+},
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/xdp_redirect_multi.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/xdp_redirect_multi.c
@@ -129,7 +129,7 @@
 		goto err_out;
 	}
 
-	printf("Get interfaces");
+	printf("Get interfaces:");
 	for (i = 0; i < MAX_IFACE_NUM && argv[optind + i]; i++) {
 		ifaces[i] = if_nametoindex(argv[optind + i]);
 		if (!ifaces[i])
@@ -139,7 +139,7 @@
 			goto err_out;
 		}
 		if (ifaces[i] > MAX_INDEX_NUM) {
-			printf("Interface index to large\n");
+			printf(" interface index too large\n");
 			goto err_out;
 		}
 		printf(" %d", ifaces[i]);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/bpf/xdping.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/bpf/xdping.c
@@ -178,9 +178,8 @@
 		return 1;
 	}
 
-	main_prog = bpf_object__find_program_by_title(obj,
-						      server ? "xdpserver" :
-							       "xdpclient");
+	main_prog = bpf_object__find_program_by_name(obj,
+						     server ? "xdping_server" : "xdping_client");
 	if (main_prog)
 		prog_fd = bpf_program__fd(main_prog);
 	if (!main_prog || prog_fd < 0) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/breakpoints/step_after_suspend_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/breakpoints/step_after_suspend_test.c
@@ -153,7 +153,10 @@
 	if (err < 0)
 		ksft_exit_fail_msg("timerfd_settime() failed\n");
 
-	if (write(power_state_fd, "mem", strlen("mem")) != strlen("mem"))
+	system("(echo mem > /sys/power/state) 2> /dev/null");
+
+	timerfd_gettime(timerfd, &spec);
+	if (spec.it_value.tv_sec != 0 || spec.it_value.tv_nsec != 0)
 		ksft_exit_fail_msg("Failed to enter Suspend state\n");
 
 	close(timerfd);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/cgroup/cgroup_util.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/cgroup/cgroup_util.c
@@ -221,7 +221,7 @@
 
 int cg_create(const char *cgroup)
 {
-	return mkdir(cgroup, 0644);
+	return mkdir(cgroup, 0755);
 }
 
 int cg_wait_for_proc_count(const char *cgroup, int count)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/cgroup/test_core.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/cgroup/test_core.c
@@ -1,11 +1,14 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 
+#define _GNU_SOURCE
 #include <linux/limits.h>
+#include <linux/sched.h>
 #include <sys/types.h>
 #include <sys/mman.h>
 #include <sys/wait.h>
 #include <unistd.h>
 #include <fcntl.h>
+#include <sched.h>
 #include <stdio.h>
 #include <errno.h>
 #include <signal.h>
@@ -674,6 +677,166 @@
 	return ret;
 }
 
+/*
+ * cgroup migration permission check should be performed based on the
+ * credentials at the time of open instead of write.
+ */
+static int test_cgcore_lesser_euid_open(const char *root)
+{
+	const uid_t test_euid = 65534;	/* usually nobody, any !root is fine */
+	int ret = KSFT_FAIL;
+	char *cg_test_a = NULL, *cg_test_b = NULL;
+	char *cg_test_a_procs = NULL, *cg_test_b_procs = NULL;
+	int cg_test_b_procs_fd = -1;
+	uid_t saved_uid;
+
+	cg_test_a = cg_name(root, "cg_test_a");
+	cg_test_b = cg_name(root, "cg_test_b");
+
+	if (!cg_test_a || !cg_test_b)
+		goto cleanup;
+
+	cg_test_a_procs = cg_name(cg_test_a, "cgroup.procs");
+	cg_test_b_procs = cg_name(cg_test_b, "cgroup.procs");
+
+	if (!cg_test_a_procs || !cg_test_b_procs)
+		goto cleanup;
+
+	if (cg_create(cg_test_a) || cg_create(cg_test_b))
+		goto cleanup;
+
+	if (cg_enter_current(cg_test_a))
+		goto cleanup;
+
+	if (chown(cg_test_a_procs, test_euid, -1) ||
+	    chown(cg_test_b_procs, test_euid, -1))
+		goto cleanup;
+
+	saved_uid = geteuid();
+	if (seteuid(test_euid))
+		goto cleanup;
+
+	cg_test_b_procs_fd = open(cg_test_b_procs, O_RDWR);
+
+	if (seteuid(saved_uid))
+		goto cleanup;
+
+	if (cg_test_b_procs_fd < 0)
+		goto cleanup;
+
+	if (write(cg_test_b_procs_fd, "0", 1) >= 0 || errno != EACCES)
+		goto cleanup;
+
+	ret = KSFT_PASS;
+
+cleanup:
+	cg_enter_current(root);
+	if (cg_test_b_procs_fd >= 0)
+		close(cg_test_b_procs_fd);
+	if (cg_test_b)
+		cg_destroy(cg_test_b);
+	if (cg_test_a)
+		cg_destroy(cg_test_a);
+	free(cg_test_b_procs);
+	free(cg_test_a_procs);
+	free(cg_test_b);
+	free(cg_test_a);
+	return ret;
+}
+
+struct lesser_ns_open_thread_arg {
+	const char	*path;
+	int		fd;
+	int		err;
+};
+
+static int lesser_ns_open_thread_fn(void *arg)
+{
+	struct lesser_ns_open_thread_arg *targ = arg;
+
+	targ->fd = open(targ->path, O_RDWR);
+	targ->err = errno;
+	return 0;
+}
+
+/*
+ * cgroup migration permission check should be performed based on the cgroup
+ * namespace at the time of open instead of write.
+ */
+static int test_cgcore_lesser_ns_open(const char *root)
+{
+	static char stack[65536];
+	const uid_t test_euid = 65534;	/* usually nobody, any !root is fine */
+	int ret = KSFT_FAIL;
+	char *cg_test_a = NULL, *cg_test_b = NULL;
+	char *cg_test_a_procs = NULL, *cg_test_b_procs = NULL;
+	int cg_test_b_procs_fd = -1;
+	struct lesser_ns_open_thread_arg targ = { .fd = -1 };
+	pid_t pid;
+	int status;
+
+	cg_test_a = cg_name(root, "cg_test_a");
+	cg_test_b = cg_name(root, "cg_test_b");
+
+	if (!cg_test_a || !cg_test_b)
+		goto cleanup;
+
+	cg_test_a_procs = cg_name(cg_test_a, "cgroup.procs");
+	cg_test_b_procs = cg_name(cg_test_b, "cgroup.procs");
+
+	if (!cg_test_a_procs || !cg_test_b_procs)
+		goto cleanup;
+
+	if (cg_create(cg_test_a) || cg_create(cg_test_b))
+		goto cleanup;
+
+	if (cg_enter_current(cg_test_b))
+		goto cleanup;
+
+	if (chown(cg_test_a_procs, test_euid, -1) ||
+	    chown(cg_test_b_procs, test_euid, -1))
+		goto cleanup;
+
+	targ.path = cg_test_b_procs;
+	pid = clone(lesser_ns_open_thread_fn, stack + sizeof(stack),
+		    CLONE_NEWCGROUP | CLONE_FILES | CLONE_VM | SIGCHLD,
+		    &targ);
+	if (pid < 0)
+		goto cleanup;
+
+	if (waitpid(pid, &status, 0) < 0)
+		goto cleanup;
+
+	if (!WIFEXITED(status))
+		goto cleanup;
+
+	cg_test_b_procs_fd = targ.fd;
+	if (cg_test_b_procs_fd < 0)
+		goto cleanup;
+
+	if (cg_enter_current(cg_test_a))
+		goto cleanup;
+
+	if ((status = write(cg_test_b_procs_fd, "0", 1)) >= 0 || errno != ENOENT)
+		goto cleanup;
+
+	ret = KSFT_PASS;
+
+cleanup:
+	cg_enter_current(root);
+	if (cg_test_b_procs_fd >= 0)
+		close(cg_test_b_procs_fd);
+	if (cg_test_b)
+		cg_destroy(cg_test_b);
+	if (cg_test_a)
+		cg_destroy(cg_test_a);
+	free(cg_test_b_procs);
+	free(cg_test_a_procs);
+	free(cg_test_b);
+	free(cg_test_a);
+	return ret;
+}
+
 #define T(x) { x, #x }
 struct corecg_test {
 	int (*fn)(const char *root);
@@ -689,6 +852,8 @@
 	T(test_cgcore_proc_migration),
 	T(test_cgcore_thread_migration),
 	T(test_cgcore_destroy),
+	T(test_cgcore_lesser_euid_open),
+	T(test_cgcore_lesser_ns_open),
 };
 #undef T
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/cgroup/test_stress.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/cgroup/test_stress.sh
@@ -1,4 +1,4 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
-./with_stress.sh -s subsys -s fork ./test_core
+./with_stress.sh -s subsys -s fork ${OUTPUT:-.}/test_core
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/clone3/clone3.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/clone3/clone3.c
@@ -52,6 +52,12 @@
 		size = sizeof(struct __clone_args);
 
 	switch (test_mode) {
+	case CLONE3_ARGS_NO_TEST:
+		/*
+		 * Uses default 'flags' and 'SIGCHLD'
+		 * assignment.
+		 */
+		break;
 	case CLONE3_ARGS_ALL_0:
 		args.flags = 0;
 		args.exit_signal = 0;
@@ -120,8 +126,6 @@
 
 int main(int argc, char *argv[])
 {
-	pid_t pid;
-
 	uid_t uid = getuid();
 
 	ksft_print_header();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/core/close_range_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/core/close_range_test.c
@@ -54,7 +54,7 @@
 #define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
 #endif
 
-TEST(close_range)
+TEST(core_close_range)
 {
 	int i, ret;
 	int open_fds[101];
@@ -567,4 +567,39 @@
 	EXPECT_EQ(close(fd3), 0);
 }
 
+TEST(close_range_bitmap_corruption)
+{
+	pid_t pid;
+	int status;
+	struct __clone_args args = {
+		.flags = CLONE_FILES,
+		.exit_signal = SIGCHLD,
+	};
+
+	/* get the first 128 descriptors open */
+	for (int i = 2; i < 128; i++)
+		EXPECT_GE(dup2(0, i), 0);
+
+	/* get descriptor table shared */
+	pid = sys_clone3(&args, sizeof(args));
+	ASSERT_GE(pid, 0);
+
+	if (pid == 0) {
+		/* unshare and truncate descriptor table down to 64 */
+		if (sys_close_range(64, ~0U, CLOSE_RANGE_UNSHARE))
+			exit(EXIT_FAILURE);
+
+		ASSERT_EQ(fcntl(64, F_GETFD), -1);
+		/* ... and verify that the range 64..127 is not
+		   stuck "fully used" according to secondary bitmap */
+		EXPECT_EQ(dup(0), 64)
+			exit(EXIT_FAILURE);
+		exit(EXIT_SUCCESS);
+	}
+
+	EXPECT_EQ(waitpid(pid, &status, 0), pid);
+	EXPECT_EQ(true, WIFEXITED(status));
+	EXPECT_EQ(0, WEXITSTATUS(status));
+}
+
 TEST_HARNESS_MAIN
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/damon/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/damon/Makefile
@@ -1,6 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 # Makefile for damon selftests
 
+TEST_GEN_FILES += huge_count_read_write
+
 TEST_FILES = _chk_dependency.sh
 TEST_PROGS = debugfs_attrs.sh
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/damon/debugfs_attrs.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/damon/debugfs_attrs.sh
@@ -72,4 +72,22 @@
 test_content "$file" "$orig_content" "" "empty input written"
 echo "$orig_content" > "$file"
 
+# Test huge count read write
+# ==========================
+
+dmesg -C
+
+for file in "$DBGFS/"*
+do
+	./huge_count_read_write "$file"
+done
+
+if dmesg | grep -q WARNING
+then
+	dmesg
+	exit 1
+else
+	exit 0
+fi
+
 echo "PASS"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/damon/huge_count_read_write.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/damon/huge_count_read_write.c
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Author: SeongJae Park <sj@kernel.org>
+ */
+
+#include <fcntl.h>
+#include <stdlib.h>
+#include <unistd.h>
+#include <stdio.h>
+
+void write_read_with_huge_count(char *file)
+{
+	int filedesc = open(file, O_RDWR);
+	char buf[25];
+	int ret;
+
+	printf("%s %s\n", __func__, file);
+	if (filedesc < 0) {
+		fprintf(stderr, "failed opening %s\n", file);
+		exit(1);
+	}
+
+	write(filedesc, "", 0xfffffffful);
+	perror("after write: ");
+	ret = read(filedesc, buf, 0xfffffffful);
+	perror("after read: ");
+	close(filedesc);
+}
+
+int main(int argc, char *argv[])
+{
+	if (argc != 2) {
+		fprintf(stderr, "Usage: %s <file>\n", argv[0]);
+		exit(1);
+	}
+	write_read_with_huge_count(argv[1]);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/dmabuf-heaps/dmabuf-heap.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/dmabuf-heaps/dmabuf-heap.c
@@ -29,9 +29,11 @@
 	version.name = name;
 
 	ret = ioctl(fd, DRM_IOCTL_VERSION, &version);
-	if (ret)
+	if (ret || version.name_len != 4)
 		return 0;
 
+	name[4] = '\0';
+
 	return !strcmp(name, "vgem");
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/mlxsw/qos_pfc.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/mlxsw/qos_pfc.sh
@@ -121,6 +121,9 @@
 
 switch_create()
 {
+	local lanes_swp4
+	local pg1_size
+
 	# pools
 	# -----
 
@@ -230,7 +233,20 @@
 	dcb pfc set dev $swp4 prio-pfc all:off 1:on
 	# PG0 will get autoconfigured to Xoff, give PG1 arbitrarily 100K, which
 	# is (-2*MTU) about 80K of delay provision.
-	dcb buffer set dev $swp4 buffer-size all:0 1:$_100KB
+	pg1_size=$_100KB
+
+	setup_wait_dev_with_timeout $swp4
+
+	lanes_swp4=$(ethtool $swp4 | grep 'Lanes:')
+	lanes_swp4=${lanes_swp4#*"Lanes: "}
+
+	# 8-lane ports use two buffers among which the configured buffer
+	# is split, so double the size to get twice (20K + 80K).
+	if [[ $lanes_swp4 -eq 8 ]]; then
+		pg1_size=$((pg1_size * 2))
+	fi
+
+	dcb buffer set dev $swp4 buffer-size all:0 1:$pg1_size
 
 	# bridges
 	# -------
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/mlxsw/sharedbuffer.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/mlxsw/sharedbuffer.sh
@@ -109,11 +109,6 @@
 	devlink sb occupancy snapshot $DEVLINK_DEV
 
 	RET=0
-	max_occ=$(sb_occ_pool_check $dl_port1 $SB_POOL_ING $exp_max_occ)
-	check_err $? "Expected iPool($SB_POOL_ING) max occupancy to be $exp_max_occ, but got $max_occ"
-	log_test "physical port's($h1) ingress pool"
-
-	RET=0
 	max_occ=$(sb_occ_pool_check $dl_port2 $SB_POOL_ING $exp_max_occ)
 	check_err $? "Expected iPool($SB_POOL_ING) max occupancy to be $exp_max_occ, but got $max_occ"
 	log_test "physical port's($h2) ingress pool"
@@ -139,11 +134,6 @@
 	RET=0
 	max_occ=$(sb_occ_itc_check $dl_port2 $SB_ITC $exp_max_occ)
 	check_err $? "Expected ingress TC($SB_ITC) max occupancy to be $exp_max_occ, but got $max_occ"
-	log_test "physical port's($h1) ingress TC - IP packet"
-
-	RET=0
-	max_occ=$(sb_occ_itc_check $dl_port2 $SB_ITC $exp_max_occ)
-	check_err $? "Expected ingress TC($SB_ITC) max occupancy to be $exp_max_occ, but got $max_occ"
 	log_test "physical port's($h2) ingress TC - IP packet"
 
 	RET=0
@@ -169,11 +159,6 @@
 
 	RET=0
 	max_occ=$(sb_occ_itc_check $dl_port2 $SB_ITC $exp_max_occ)
-	check_err $? "Expected ingress TC($SB_ITC) max occupancy to be $exp_max_occ, but got $max_occ"
-	log_test "physical port's($h1) ingress TC - ARP packet"
-
-	RET=0
-	max_occ=$(sb_occ_itc_check $dl_port2 $SB_ITC $exp_max_occ)
 	check_err $? "Expected ingress TC($SB_ITC) max occupancy to be $exp_max_occ, but got $max_occ"
 	log_test "physical port's($h2) ingress TC - ARP packet"
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/mlxsw/spectrum-2/tc_flower.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/mlxsw/spectrum-2/tc_flower.sh
@@ -10,7 +10,8 @@
 ALL_TESTS="single_mask_test identical_filters_test two_masks_test \
 	multiple_masks_test ctcam_edge_cases_test delta_simple_test \
 	delta_two_masks_one_key_test delta_simple_rehash_test \
-	bloom_simple_test bloom_complex_test bloom_delta_test"
+	bloom_simple_test bloom_complex_test bloom_delta_test \
+	max_erp_entries_test max_group_size_test collision_test"
 NUM_NETIFS=2
 source $lib_dir/lib.sh
 source $lib_dir/tc_common.sh
@@ -456,7 +457,7 @@
 {
 	# If 2 keys are the same and only differ in mask in a way that
 	# they belong under the same ERP (second is delta of the first),
-	# there should be no C-TCAM spill.
+	# there should be C-TCAM spill.
 
 	RET=0
 
@@ -473,8 +474,8 @@
 	tp_record "mlxsw:*" "tc filter add dev $h2 ingress protocol ip \
 		   pref 2 handle 102 flower $tcflags dst_ip 192.0.2.2 \
 		   action drop"
-	tp_check_hits "mlxsw:mlxsw_sp_acl_atcam_entry_add_ctcam_spill" 0
-	check_err $? "incorrect C-TCAM spill while inserting the second rule"
+	tp_check_hits "mlxsw:mlxsw_sp_acl_atcam_entry_add_ctcam_spill" 1
+	check_err $? "C-TCAM spill did not happen while inserting the second rule"
 
 	$MZ $h1 -c 1 -p 64 -a $h1mac -b $h2mac -A 192.0.2.1 -B 192.0.2.2 \
 		-t ip -q
@@ -983,6 +984,156 @@
 	log_test "bloom delta test ($tcflags)"
 }
 
+max_erp_entries_test()
+{
+	# The number of eRP entries is limited. Once the maximum number of eRPs
+	# has been reached, filters cannot be added. This test verifies that
+	# when this limit is reached, inserstion fails without crashing.
+
+	RET=0
+
+	local num_masks=32
+	local num_regions=15
+	local chain_failed
+	local mask_failed
+	local ret
+
+	if [[ "$tcflags" != "skip_sw" ]]; then
+		return 0;
+	fi
+
+	for ((i=1; i < $num_regions; i++)); do
+		for ((j=$num_masks; j >= 0; j--)); do
+			tc filter add dev $h2 ingress chain $i protocol ip \
+				pref $i	handle $j flower $tcflags \
+				dst_ip 192.1.0.0/$j &> /dev/null
+			ret=$?
+
+			if [ $ret -ne 0 ]; then
+				chain_failed=$i
+				mask_failed=$j
+				break 2
+			fi
+		done
+	done
+
+	# We expect to exceed the maximum number of eRP entries, so that
+	# insertion eventually fails. Otherwise, the test should be adjusted to
+	# add more filters.
+	check_fail $ret "expected to exceed number of eRP entries"
+
+	for ((; i >= 1; i--)); do
+		for ((j=0; j <= $num_masks; j++)); do
+			tc filter del dev $h2 ingress chain $i protocol ip \
+				pref $i handle $j flower &> /dev/null
+		done
+	done
+
+	log_test "max eRP entries test ($tcflags). " \
+		"max chain $chain_failed, mask $mask_failed"
+}
+
+max_group_size_test()
+{
+	# The number of ACLs in an ACL group is limited. Once the maximum
+	# number of ACLs has been reached, filters cannot be added. This test
+	# verifies that when this limit is reached, insertion fails without
+	# crashing.
+
+	RET=0
+
+	local num_acls=32
+	local max_size
+	local ret
+
+	if [[ "$tcflags" != "skip_sw" ]]; then
+		return 0;
+	fi
+
+	for ((i=1; i < $num_acls; i++)); do
+		if [[ $(( i % 2 )) == 1 ]]; then
+			tc filter add dev $h2 ingress pref $i proto ipv4 \
+				flower $tcflags dst_ip 198.51.100.1/32 \
+				ip_proto tcp tcp_flags 0x01/0x01 \
+				action drop &> /dev/null
+		else
+			tc filter add dev $h2 ingress pref $i proto ipv6 \
+				flower $tcflags dst_ip 2001:db8:1::1/128 \
+				action drop &> /dev/null
+		fi
+
+		ret=$?
+		[[ $ret -ne 0 ]] && max_size=$((i - 1)) && break
+	done
+
+	# We expect to exceed the maximum number of ACLs in a group, so that
+	# insertion eventually fails. Otherwise, the test should be adjusted to
+	# add more filters.
+	check_fail $ret "expected to exceed number of ACLs in a group"
+
+	for ((; i >= 1; i--)); do
+		if [[ $(( i % 2 )) == 1 ]]; then
+			tc filter del dev $h2 ingress pref $i proto ipv4 \
+				flower $tcflags dst_ip 198.51.100.1/32 \
+				ip_proto tcp tcp_flags 0x01/0x01 \
+				action drop &> /dev/null
+		else
+			tc filter del dev $h2 ingress pref $i proto ipv6 \
+				flower $tcflags dst_ip 2001:db8:1::1/128 \
+				action drop &> /dev/null
+		fi
+	done
+
+	log_test "max ACL group size test ($tcflags). max size $max_size"
+}
+
+collision_test()
+{
+	# Filters cannot share an eRP if in the common unmasked part (i.e.,
+	# without the delta bits) they have the same values. If the driver does
+	# not prevent such configuration (by spilling into the C-TCAM), then
+	# multiple entries will be present in the device with the same key,
+	# leading to collisions and a reduced scale.
+	#
+	# Create such a scenario and make sure all the filters are successfully
+	# added.
+
+	RET=0
+
+	local ret
+
+	if [[ "$tcflags" != "skip_sw" ]]; then
+		return 0;
+	fi
+
+	# Add a single dst_ip/24 filter and multiple dst_ip/32 filters that all
+	# have the same values in the common unmasked part (dst_ip/24).
+
+	tc filter add dev $h2 ingress pref 1 proto ipv4 handle 101 \
+		flower $tcflags dst_ip 198.51.100.0/24 \
+		action drop
+
+	for i in {0..255}; do
+		tc filter add dev $h2 ingress pref 2 proto ipv4 \
+			handle $((102 + i)) \
+			flower $tcflags dst_ip 198.51.100.${i}/32 \
+			action drop
+		ret=$?
+		[[ $ret -ne 0 ]] && break
+	done
+
+	check_err $ret "failed to add all the filters"
+
+	for i in {255..0}; do
+		tc filter del dev $h2 ingress pref 2 proto ipv4 \
+			handle $((102 + i)) flower
+	done
+
+	tc filter del dev $h2 ingress pref 1 proto ipv4 handle 101 flower
+
+	log_test "collision test ($tcflags)"
+}
+
 setup_prepare()
 {
 	h1=${NETIFS[p1]}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/mlxsw/spectrum/resource_scale.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/mlxsw/spectrum/resource_scale.sh
@@ -50,8 +50,8 @@
 			else
 				log_test "'$current_test' [$profile] overflow $target"
 			fi
+			RET_FIN=$(( RET_FIN || RET ))
 		done
-		RET_FIN=$(( RET_FIN || RET ))
 	done
 done
 current_test=""
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/mlxsw/tc_police_scale.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/mlxsw/tc_police_scale.sh
@@ -60,7 +60,8 @@
 
 	tc_police_rules_create $count $should_fail
 
-	offload_count=$(tc filter show dev $swp1 ingress | grep in_hw | wc -l)
+	offload_count=$(tc -j filter show dev $swp1 ingress |
+			jq "[.[] | select(.options.in_hw == true)] | length")
 	((offload_count == count))
 	check_err_fail $should_fail $? "tc police offload count"
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/mlxsw/vxlan_flooding.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/mlxsw/vxlan_flooding.sh
@@ -172,6 +172,17 @@
 	local lsb
 	local i
 
+	# Prevent unwanted packets from entering the bridge and interfering
+	# with the test.
+	tc qdisc add dev br0 clsact
+	tc filter add dev br0 egress protocol all pref 1 handle 1 \
+		matchall skip_hw action drop
+	tc qdisc add dev $h1 clsact
+	tc filter add dev $h1 egress protocol all pref 1 handle 1 \
+		flower skip_hw dst_mac de:ad:be:ef:13:37 action pass
+	tc filter add dev $h1 egress protocol all pref 2 handle 2 \
+		matchall skip_hw action drop
+
 	tc qdisc add dev $rp2 clsact
 
 	for i in $(eval echo {1..$num_remotes}); do
@@ -194,6 +205,12 @@
 	done
 
 	tc qdisc del dev $rp2 clsact
+
+	tc filter del dev $h1 egress protocol all pref 2 handle 2 matchall
+	tc filter del dev $h1 egress protocol all pref 1 handle 1 flower
+	tc qdisc del dev $h1 clsact
+	tc filter del dev br0 egress protocol all pref 1 handle 1 matchall
+	tc qdisc del dev br0 clsact
 }
 
 flooding_check_packets()
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/netdevsim/devlink.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/netdevsim/devlink.sh
@@ -17,6 +17,18 @@
 DEBUGFS_DIR=/sys/kernel/debug/netdevsim/$DEV_NAME/
 DL_HANDLE=netdevsim/$DEV_NAME
 
+wait_for_devlink()
+{
+	"$@" | grep -q $DL_HANDLE
+}
+
+devlink_wait()
+{
+	local timeout=$1
+
+	busywait "$timeout" wait_for_devlink devlink dev
+}
+
 fw_flash_test()
 {
 	RET=0
@@ -256,6 +268,9 @@
 	ip netns del testns2
 	ip netns del testns1
 
+	# Wait until netns async cleanup is done.
+	devlink_wait 2000
+
 	log_test "netns reload test"
 }
 
@@ -348,6 +363,9 @@
 	ip netns del testns2
 	ip netns del testns1
 
+	# Wait until netns async cleanup is done.
+	devlink_wait 2000
+
 	log_test "resource test"
 }
 
@@ -496,8 +514,8 @@
 
 	check_reporter_info dummy healthy 3 3 10 true
 
-	echo 8192> $DEBUGFS_DIR/health/binary_len
-	check_fail $? "Failed set dummy reporter binary len to 8192"
+	echo 8192 > $DEBUGFS_DIR/health/binary_len
+	check_err $? "Failed set dummy reporter binary len to 8192"
 
 	local dump=$(devlink health dump show $DL_HANDLE reporter dummy -j)
 	check_err $? "Failed show dump of dummy reporter"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/netdevsim/udp_tunnel_nic.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/netdevsim/udp_tunnel_nic.sh
@@ -142,7 +142,7 @@
 }
 
 function check_table {
-    local path=$NSIM_DEV_DFS/ports/$port/udp_ports_table$1
+    local path=$NSIM_DEV_DFS/ports/$port/udp_ports/table$1
     local -n expected=$2
     local last=$3
 
@@ -212,7 +212,7 @@
 }
 
 function print_table {
-    local path=$NSIM_DEV_DFS/ports/$port/udp_ports_table$1
+    local path=$NSIM_DEV_DFS/ports/$port/udp_ports/table$1
     read -a have < $path
 
     tree $NSIM_DEV_DFS/
@@ -269,6 +269,7 @@
 	echo 1 > $NSIM_DEV_SYS/new_port
     fi
     NSIM_NETDEV=`get_netdev_name old_netdevs`
+    ifconfig $NSIM_NETDEV up
 
     msg="new NIC device created"
     exp0=( 0 0 0 0 )
@@ -430,6 +431,7 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
     overflow_table0 "overflow NIC table"
@@ -487,6 +489,7 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
     overflow_table0 "overflow NIC table"
@@ -543,6 +546,7 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
     overflow_table0 "destroy NIC"
@@ -572,6 +576,7 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
     msg="create VxLANs v6"
@@ -632,9 +637,10 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
-    echo 110 > $NSIM_DEV_DFS/ports/$port/udp_ports_inject_error
+    echo 110 > $NSIM_DEV_DFS/ports/$port/udp_ports/inject_error
 
     msg="1 - create VxLANs v6"
     exp0=( 0 0 0 0 )
@@ -656,7 +662,7 @@
     new_geneve gnv0 20000
 
     msg="2 - destroy GENEVE"
-    echo 2 > $NSIM_DEV_DFS/ports/$port/udp_ports_inject_error
+    echo 2 > $NSIM_DEV_DFS/ports/$port/udp_ports/inject_error
     exp1=( `mke 20000 2` 0 0 0 )
     del_dev gnv0
 
@@ -687,6 +693,7 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
     msg="create VxLANs v6"
@@ -746,6 +753,7 @@
     fi
 
     echo $port > $NSIM_DEV_SYS/new_port
+    NSIM_NETDEV=`get_netdev_name old_netdevs`
     ifconfig $NSIM_NETDEV up
 
     msg="create VxLANs v6"
@@ -755,7 +763,7 @@
     msg="create VxLANs v4"
     new_vxlan vxlan0 10000 $NSIM_NETDEV
 
-    echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports_reset
+    echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports/reset
     check_tables
 
     msg="NIC device goes down"
@@ -766,7 +774,7 @@
     fi
     check_tables
 
-    echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports_reset
+    echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports/reset
     check_tables
 
     msg="NIC device goes up again"
@@ -780,7 +788,7 @@
     del_dev vxlan0
     check_tables
 
-    echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports_reset
+    echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports/reset
     check_tables
 
     msg="destroy NIC"
@@ -876,6 +884,7 @@
 
 echo 2 > $NSIM_DEV_SYS/del_port
 echo 2 > $NSIM_DEV_SYS/new_port
+NSIM_NETDEV=`get_netdev_name old_netdevs`
 check_tables
 
 msg="replace VxLAN in overflow table"
@@ -886,7 +895,7 @@
 exp0=( `mke 10000 1` `mke 10004 1` 0 `mke 10003 1` )
 del_dev vxlan2
 
-echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports_reset
+echo 1 > $NSIM_DEV_DFS/ports/$port/udp_ports/reset
 check_tables
 
 msg="tunnels destroyed 2"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/drivers/net/ocelot/tc_flower_chains.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/drivers/net/ocelot/tc_flower_chains.sh
@@ -185,7 +185,7 @@
 
 	tc filter add dev $eth0 ingress chain $(IS2 0 0) pref 1 \
 		protocol ipv4 flower skip_sw ip_proto udp dst_port 5201 \
-		action police rate 50mbit burst 64k \
+		action police rate 50mbit burst 64k conform-exceed drop/pipe \
 		action goto chain $(IS2 1 0)
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/efivarfs/create-read.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/efivarfs/create-read.c
@@ -32,8 +32,10 @@
 	rc = read(fd, buf, sizeof(buf));
 	if (rc != 0) {
 		fprintf(stderr, "Reading a new var should return EOF\n");
+		close(fd);
 		return EXIT_FAILURE;
 	}
 
+	close(fd);
 	return EXIT_SUCCESS;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/efivarfs/efivarfs.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/efivarfs/efivarfs.sh
@@ -87,6 +87,11 @@
 {
 	local file=$efivarfs_mount/$FUNCNAME-$test_guid
 	./create-read $file
+	if [ $? -ne 0 ]; then
+		echo "create and read $file failed"
+		file_cleanup $file
+		exit 1
+	fi
 	file_cleanup $file
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/exec/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/exec/Makefile
@@ -3,9 +3,9 @@
 CFLAGS += -Wno-nonnull
 CFLAGS += -D_GNU_SOURCE
 
-TEST_PROGS := binfmt_script non-regular
-TEST_GEN_PROGS := execveat load_address_4096 load_address_2097152 load_address_16777216
-TEST_GEN_FILES := execveat.symlink execveat.denatured script subdir pipe
+TEST_PROGS := binfmt_script
+TEST_GEN_PROGS := execveat load_address_4096 load_address_2097152 load_address_16777216 non-regular
+TEST_GEN_FILES := execveat.symlink execveat.denatured script subdir
 # Makefile is a run-time dependency, since it's accessed by the execveat test
 TEST_FILES := Makefile
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/filesystems/binderfs/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/filesystems/binderfs/Makefile
@@ -3,6 +3,4 @@
 CFLAGS += -I../../../../../usr/include/ -pthread
 TEST_GEN_PROGS := binderfs_test
 
-binderfs_test: binderfs_test.c ../../kselftest.h ../../kselftest_harness.h
-
 include ../../lib.mk
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/ftracetest
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/ftracetest
@@ -30,6 +30,9 @@
 # kselftest skip code is 4
 err_skip=4
 
+# umount required
+UMOUNT_DIR=""
+
 # cgroup RT scheduling prevents chrt commands from succeeding, which
 # induces failures in test wakeup tests.  Disable for the duration of
 # the tests.
@@ -44,6 +47,9 @@
 
 cleanup() {
   echo $sched_rt_runtime_orig > $sched_rt_runtime
+  if [ -n "${UMOUNT_DIR}" ]; then
+    umount ${UMOUNT_DIR} ||:
+  fi
 }
 
 errexit() { # message
@@ -155,11 +161,13 @@
 	    mount -t tracefs nodev /sys/kernel/tracing ||
 	      errexit "Failed to mount /sys/kernel/tracing"
 	    TRACING_DIR="/sys/kernel/tracing"
+	    UMOUNT_DIR=${TRACING_DIR}
 	# If debugfs exists, then so does /sys/kernel/debug
 	elif [ -d "/sys/kernel/debug" ]; then
 	    mount -t debugfs nodev /sys/kernel/debug ||
 	      errexit "Failed to mount /sys/kernel/debug"
 	    TRACING_DIR="/sys/kernel/debug/tracing"
+	    UMOUNT_DIR=${TRACING_DIR}
 	else
 	    err_ret=$err_skip
 	    errexit "debugfs and tracefs are not configured in this kernel"
@@ -428,7 +436,7 @@
     exit 1
   fi
 done
-(cd $TRACING_DIR; initialize_ftrace) # for cleanup
+(cd $TRACING_DIR; finish_ftrace) # for cleanup
 
 prlog ""
 prlog "# of passed: " `echo $PASSED_CASES | wc -w`
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/dynevent/test_duplicates.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/dynevent/test_duplicates.tc
@@ -1,7 +1,7 @@
 #!/bin/sh
 # SPDX-License-Identifier: GPL-2.0
 # description: Generic dynamic event - check if duplicate events are caught
-# requires: dynamic_events "e[:[<group>/]<event>] <attached-group>.<attached-event> [<args>]":README
+# requires: dynamic_events events/syscalls/sys_enter_openat "e[:[<group>/]<event>] <attached-group>.<attached-event> [<args>]":README
 
 echo 0 > events/enable
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/event/subsystem-enable.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/event/subsystem-enable.tc
@@ -18,7 +18,7 @@
 
 yield
 
-count=`cat trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l`
+count=`head -n 100 trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l`
 if [ $count -lt 3 ]; then
     fail "at least fork, exec and exit events should be recorded"
 fi
@@ -29,7 +29,7 @@
 
 yield
 
-count=`cat trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l`
+count=`head -n 100 trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l`
 if [ $count -lt 3 ]; then
     fail "at least fork, exec and exit events should be recorded"
 fi
@@ -40,7 +40,7 @@
 
 yield
 
-count=`cat trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l`
+count=`head -n 100 trace | grep -v ^# | awk '{ print $5 }' | sort -u | wc -l`
 if [ $count -ne 0 ]; then
     fail "any of scheduler events should not be recorded"
 fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/ftrace/func_event_triggers.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/ftrace/func_event_triggers.tc
@@ -38,11 +38,18 @@
 
 test_event_enabled() {
     val=$1
+    check_times=10		# wait for 10 * SLEEP_TIME at most
 
-    e=`cat $EVENT_ENABLE`
-    if [ "$e" != $val ]; then
-	fail "Expected $val but found $e"
-    fi
+    while [ $check_times -ne 0 ]; do
+	e=`cat $EVENT_ENABLE`
+	if [ "$e" = $val ]; then
+	    return 0
+	fi
+	sleep $SLEEP_TIME
+	check_times=$((check_times - 1))
+    done
+
+    fail "Expected $val but found $e"
 }
 
 run_enable_disable() {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/ftrace/func_set_ftrace_file.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/ftrace/func_set_ftrace_file.tc
@@ -19,7 +19,7 @@
 
 FILTER=set_ftrace_filter
 FUNC1="schedule"
-FUNC2="do_softirq"
+FUNC2="scheduler_tick"
 
 ALL_FUNCS="#### all functions enabled ####"
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/functions
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/functions
@@ -124,10 +124,22 @@
     [ -f uprobe_events ] && echo > uprobe_events
     [ -f synthetic_events ] && echo > synthetic_events
     [ -f snapshot ] && echo 0 > snapshot
+
+# Stop tracing while reading the trace file by default, to prevent
+# the test results while checking it and to avoid taking a long time
+# to check the result.
+    [ -f options/pause-on-trace ] && echo 1 > options/pause-on-trace
+
     clear_trace
     enable_tracing
 }
 
+finish_ftrace() {
+    initialize_ftrace
+# And recover it to default.
+    [ -f options/pause-on-trace ] && echo 0 > options/pause-on-trace
+}
+
 check_requires() { # Check required files and tracers
     for i in "$@" ; do
         r=${i%:README}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/instances/instance-event.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/instances/instance-event.tc
@@ -39,7 +39,7 @@
 
 instance_set() {
         while :; do
-                echo 1 > foo/events/sched/sched_switch
+                echo 1 > foo/events/sched/sched_switch/enable
         done 2> /dev/null
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_eventname.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_eventname.tc
@@ -30,7 +30,8 @@
 	fi
 
 	grep " [tT] .*\.isra\..*" /proc/kallsyms | cut -f 3 -d " " | while read f; do
-		if grep -s $f available_filter_functions; then
+		cnt=`grep -s $f available_filter_functions | wc -l`;
+		if [ $cnt -eq 1 ]; then
 			echo $f
 			break
 		fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_non_uniq_symbol.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_non_uniq_symbol.tc
@@ -0,0 +1,13 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0
+# description: Test failure of registering kprobe on non unique symbol
+# requires: kprobe_events
+
+SYMBOL='name_show'
+
+# We skip this test on kernel where SYMBOL is unique or does not exist.
+if [ "$(grep -c -E "[[:alnum:]]+ t ${SYMBOL}" /proc/kallsyms)" -le '1' ]; then
+	exit_unsupported
+fi
+
+! echo "p:test_non_unique ${SYMBOL}" > kprobe_events
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_syntax_errors.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_syntax_errors.tc
@@ -21,7 +21,6 @@
 check_error 'p:^12345678901234567890123456789012345678901234567890123456789012345/bar vfs_read'	# GROUP_TOO_LONG
 
 check_error 'p:^foo.1/bar vfs_read'	# BAD_GROUP_NAME
-check_error 'p:foo/^ vfs_read'		# NO_EVENT_NAME
 check_error 'p:foo/^12345678901234567890123456789012345678901234567890123456789012345 vfs_read'	# EVENT_TOO_LONG
 check_error 'p:foo/^bar.1 vfs_read'	# BAD_EVENT_NAME
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/kprobe/profile.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/kprobe/profile.tc
@@ -1,6 +1,6 @@
 #!/bin/sh
 # SPDX-License-Identifier: GPL-2.0
-# description: Kprobe dynamic event - adding and removing
+# description: Kprobe profile
 # requires: kprobe_events
 
 ! grep -q 'myevent' kprobe_profile
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ftrace/test.d/trigger/trigger-trace-marker-snapshot.tc
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ftrace/test.d/trigger/trigger-trace-marker-snapshot.tc
@@ -14,12 +14,12 @@
     x=$2
 
     cat $file | while read line; do
-	comment=`echo $line | sed -e 's/^#//'`
+	comment=`echo "$line" | sed -e 's/^#//'`
 	if [ "$line" != "$comment" ]; then
 	    continue
 	fi
 	echo "testing $line for >$x<"
-	match=`echo $line | sed -e "s/>$x<//"`
+	match=`echo "$line" | sed -e "s/>$x<//"`
 	if [ "$line" = "$match" ]; then
 	    fail "$line does not have >$x< in it"
 	fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/futex/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/futex/Makefile
@@ -11,7 +11,7 @@
 	@for DIR in $(SUBDIRS); do		\
 		BUILD_TARGET=$(OUTPUT)/$$DIR;	\
 		mkdir $$BUILD_TARGET  -p;	\
-		make OUTPUT=$$BUILD_TARGET -C $$DIR $@;\
+		$(MAKE) OUTPUT=$$BUILD_TARGET -C $$DIR $@;\
 		if [ -e $$DIR/$(TEST_PROGS) ]; then \
 			rsync -a $$DIR/$(TEST_PROGS) $$BUILD_TARGET/; \
 		fi \
@@ -32,6 +32,6 @@
 	@for DIR in $(SUBDIRS); do		\
 		BUILD_TARGET=$(OUTPUT)/$$DIR;	\
 		mkdir $$BUILD_TARGET  -p;	\
-		make OUTPUT=$$BUILD_TARGET -C $$DIR $@;\
+		$(MAKE) OUTPUT=$$BUILD_TARGET -C $$DIR $@;\
 	done
 endef
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/futex/functional/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/futex/functional/Makefile
@@ -4,11 +4,11 @@
 CFLAGS := $(CFLAGS) -g -O2 -Wall -D_GNU_SOURCE -pthread $(INCLUDES)
 LDLIBS := -lpthread -lrt
 
-HEADERS := \
+LOCAL_HDRS := \
 	../include/futextest.h \
 	../include/atomic.h \
 	../include/logging.h
-TEST_GEN_FILES := \
+TEST_GEN_PROGS := \
 	futex_wait_timeout \
 	futex_wait_wouldblock \
 	futex_requeue_pi \
@@ -24,5 +24,3 @@
 top_srcdir = ../../../../..
 KSFT_KHDR_INSTALL := 1
 include ../../lib.mk
-
-$(TEST_GEN_FILES): $(HEADERS)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/futex/functional/futex_wait_timeout.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/futex/functional/futex_wait_timeout.c
@@ -23,6 +23,7 @@
 
 static long timeout_ns = 100000;	/* 100us default timeout */
 static futex_t futex_pi;
+static pthread_barrier_t barrier;
 
 void usage(char *prog)
 {
@@ -47,6 +48,8 @@
 	if (ret != 0)
 		error("futex_lock_pi failed\n", ret);
 
+	pthread_barrier_wait(&barrier);
+
 	/* Blocks forever */
 	ret = futex_wait(&lock, 0, NULL, 0);
 	error("futex_wait failed\n", ret);
@@ -123,6 +126,7 @@
 	       basename(argv[0]));
 	ksft_print_msg("\tArguments: timeout=%ldns\n", timeout_ns);
 
+	pthread_barrier_init(&barrier, NULL, 2);
 	pthread_create(&thread, NULL, get_pi_lock, NULL);
 
 	/* initialize relative timeout */
@@ -156,6 +160,9 @@
 	res = futex_wait_requeue_pi(&f1, f1, &futex_pi, &to, 0);
 	test_timeout(res, &ret, "futex_wait_requeue_pi monotonic", ETIMEDOUT);
 
+	/* Wait until the other thread calls futex_lock_pi() */
+	pthread_barrier_wait(&barrier);
+	pthread_barrier_destroy(&barrier);
 	/*
 	 * FUTEX_LOCK_PI with CLOCK_REALTIME
 	 * Due to historical reasons, FUTEX_LOCK_PI supports only realtime
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/gpio/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/gpio/Makefile
@@ -3,5 +3,6 @@
 TEST_PROGS := gpio-mockup.sh
 TEST_FILES := gpio-mockup-sysfs.sh
 TEST_GEN_PROGS_EXTENDED := gpio-mockup-cdev
+CFLAGS += -I../../../../usr/include
 
 include ../lib.mk
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/intel_pstate/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/intel_pstate/Makefile
@@ -2,10 +2,10 @@
 CFLAGS := $(CFLAGS) -Wall -D_GNU_SOURCE
 LDLIBS += -lm
 
-uname_M := $(shell uname -m 2>/dev/null || echo not)
-ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/x86/ -e s/x86_64/x86/)
+ARCH ?= $(shell uname -m 2>/dev/null || echo not)
+ARCH_PROCESSED := $(shell echo $(ARCH) | sed -e s/i.86/x86/ -e s/x86_64/x86/)
 
-ifeq (x86,$(ARCH))
+ifeq (x86,$(ARCH_PROCESSED))
 TEST_GEN_FILES := msr aperf
 endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kcmp/kcmp_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kcmp/kcmp_test.c
@@ -88,7 +88,10 @@
 		int pid2 = getpid();
 		int ret;
 
-		fd2 = open(kpath, O_RDWR, 0644);
+		ksft_print_header();
+		ksft_set_plan(3);
+
+		fd2 = open(kpath, O_RDWR);
 		if (fd2 < 0) {
 			perror("Can't open file");
 			ksft_exit_fail();
@@ -152,7 +155,6 @@
 			ksft_inc_pass_cnt();
 		}
 
-		ksft_print_cnts();
 
 		if (ret)
 			ksft_exit_fail();
@@ -162,5 +164,5 @@
 
 	waitpid(pid2, &status, P_ALL);
 
-	return ksft_exit_pass();
+	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kselftest.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kselftest.h
@@ -48,6 +48,25 @@
 #include <stdarg.h>
 #include <stdio.h>
 
+#ifndef ARRAY_SIZE
+#define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]))
+#endif
+
+/*
+ * gcc cpuid.h provides __cpuid_count() since v4.4.
+ * Clang/LLVM cpuid.h provides  __cpuid_count() since v3.4.0.
+ *
+ * Provide local define for tests needing __cpuid_count() because
+ * selftests need to work in older environments that do not yet
+ * have __cpuid_count().
+ */
+#ifndef __cpuid_count
+#define __cpuid_count(level, count, a, b, c, d)				\
+	__asm__ __volatile__ ("cpuid\n\t"				\
+			      : "=a" (a), "=b" (b), "=c" (c), "=d" (d)	\
+			      : "0" (level), "2" (count))
+#endif
+
 /* define kselftest exit codes */
 #define KSFT_PASS  0
 #define KSFT_FAIL  1
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kselftest/runner.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kselftest/runner.sh
@@ -32,10 +32,11 @@
 tap_timeout()
 {
 	# Make sure tests will time out if utility is available.
-	if [ -x /usr/bin/timeout ] ; then
-		/usr/bin/timeout --foreground "$kselftest_timeout" "$1"
+	if [ -x /usr/bin/timeout ] && [ $kselftest_timeout -gt 0 ] ; then
+		/usr/bin/timeout --foreground "$kselftest_timeout" \
+			/usr/bin/timeout "$kselftest_timeout" $1
 	else
-		"$1"
+		$1
 	fi
 }
 
@@ -65,17 +66,25 @@
 
 	TEST_HDR_MSG="selftests: $DIR: $BASENAME_TEST"
 	echo "# $TEST_HDR_MSG"
-	if [ ! -x "$TEST" ]; then
-		echo -n "# Warning: file $TEST is "
-		if [ ! -e "$TEST" ]; then
-			echo "missing!"
-		else
-			echo "not executable, correct this."
-		fi
+	if [ ! -e "$TEST" ]; then
+		echo "# Warning: file $TEST is missing!"
 		echo "not ok $test_num $TEST_HDR_MSG"
 	else
+		cmd="./$BASENAME_TEST"
+		if [ ! -x "$TEST" ]; then
+			echo "# Warning: file $TEST is not executable"
+
+			if [ $(head -n 1 "$TEST" | cut -c -2) = "#!" ]
+			then
+				interpreter=$(head -n 1 "$TEST" | cut -c 3-)
+				cmd="$interpreter ./$BASENAME_TEST"
+			else
+				echo "not ok $test_num $TEST_HDR_MSG"
+				return
+			fi
+		fi
 		cd `dirname $TEST` > /dev/null
-		((((( tap_timeout ./$BASENAME_TEST 2>&1; echo $? >&3) |
+		((((( tap_timeout "$cmd" 2>&1; echo $? >&3) |
 			tap_prefix >&4) 3>&1) |
 			(read xs; exit $xs)) 4>>"$logfile" &&
 		echo "ok $test_num $TEST_HDR_MSG") ||
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kselftest_deps.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kselftest_deps.sh
@@ -46,11 +46,11 @@
 print_targets=0
 
 while getopts "p" arg; do
-    case $arg in
-        p)
+	case $arg in
+		p)
 		print_targets=1
 	shift;;
-    esac
+	esac
 done
 
 if [ $# -eq 0 ]
@@ -92,6 +92,10 @@
 # Get all TARGETS from selftests Makefile
 targets=$(egrep "^TARGETS +|^TARGETS =" Makefile | cut -d "=" -f2)
 
+# Initially, in LDLIBS related lines, the dep checker needs
+# to ignore lines containing the following strings:
+filter="\$(VAR_LDLIBS)\|pkg-config\|PKG_CONFIG\|IOURING_EXTRA_LIBS"
+
 # Single test case
 if [ $# -eq 2 ]
 then
@@ -100,6 +104,8 @@
 	l1_test $test
 	l2_test $test
 	l3_test $test
+	l4_test $test
+	l5_test $test
 
 	print_results $1 $2
 	exit $?
@@ -113,7 +119,7 @@
 # Append space at the end of the list to append more tests.
 
 l1_tests=$(grep -r --include=Makefile "^LDLIBS" | \
-		grep -v "VAR_LDLIBS" | awk -F: '{print $1}')
+		grep -v "$filter" | awk -F: '{print $1}' | uniq)
 
 # Level 2: LDLIBS set dynamically.
 #
@@ -126,7 +132,7 @@
 # Append space at the end of the list to append more tests.
 
 l2_tests=$(grep -r --include=Makefile ": LDLIBS" | \
-		grep -v "VAR_LDLIBS" | awk -F: '{print $1}')
+		grep -v "$filter" | awk -F: '{print $1}' | uniq)
 
 # Level 3
 # memfd and others use pkg-config to find mount and fuse libs
@@ -138,11 +144,32 @@
 #	VAR_LDLIBS := $(shell pkg-config fuse --libs 2>/dev/null)
 
 l3_tests=$(grep -r --include=Makefile "^VAR_LDLIBS" | \
-		grep -v "pkg-config" | awk -F: '{print $1}')
+		grep -v "pkg-config\|PKG_CONFIG" | awk -F: '{print $1}' | uniq)
 
-#echo $l1_tests
-#echo $l2_1_tests
-#echo $l3_tests
+# Level 4
+# some tests may fall back to default using `|| echo -l<libname>`
+# if pkg-config doesn't find the libs, instead of using VAR_LDLIBS
+# as per level 3 checks.
+# e.g:
+# netfilter/Makefile
+#	LDLIBS += $(shell $(HOSTPKG_CONFIG) --libs libmnl 2>/dev/null || echo -lmnl)
+l4_tests=$(grep -r --include=Makefile "^LDLIBS" | \
+		grep "pkg-config\|PKG_CONFIG" | awk -F: '{print $1}' | uniq)
+
+# Level 5
+# some tests may use IOURING_EXTRA_LIBS to add extra libs to LDLIBS,
+# which in turn may be defined in a sub-Makefile
+# e.g.:
+# mm/Makefile
+#	$(OUTPUT)/gup_longterm: LDLIBS += $(IOURING_EXTRA_LIBS)
+l5_tests=$(grep -r --include=Makefile "LDLIBS +=.*\$(IOURING_EXTRA_LIBS)" | \
+	awk -F: '{print $1}' | uniq)
+
+#echo l1_tests $l1_tests
+#echo l2_tests $l2_tests
+#echo l3_tests $l3_tests
+#echo l4_tests $l4_tests
+#echo l5_tests $l5_tests
 
 all_tests
 print_results $1 $2
@@ -164,24 +191,32 @@
 	for test in $l3_tests; do
 		l3_test $test
 	done
+
+	for test in $l4_tests; do
+		l4_test $test
+	done
+
+	for test in $l5_tests; do
+		l5_test $test
+	done
 }
 
 # Use same parsing used for l1_tests and pick libraries this time.
 l1_test()
 {
 	test_libs=$(grep --include=Makefile "^LDLIBS" $test | \
-			grep -v "VAR_LDLIBS" | \
+			grep -v "$filter" | \
 			sed -e 's/\:/ /' | \
 			sed -e 's/+/ /' | cut -d "=" -f 2)
 
 	check_libs $test $test_libs
 }
 
-# Use same parsing used for l2__tests and pick libraries this time.
+# Use same parsing used for l2_tests and pick libraries this time.
 l2_test()
 {
 	test_libs=$(grep --include=Makefile ": LDLIBS" $test | \
-			grep -v "VAR_LDLIBS" | \
+			grep -v "$filter" | \
 			sed -e 's/\:/ /' | sed -e 's/+/ /' | \
 			cut -d "=" -f 2)
 
@@ -196,6 +231,24 @@
 
 	check_libs $test $test_libs
 }
+
+l4_test()
+{
+	test_libs=$(grep --include=Makefile "^VAR_LDLIBS\|^LDLIBS" $test | \
+			grep "\(pkg-config\|PKG_CONFIG\).*|| echo " | \
+			sed -e 's/.*|| echo //' | sed -e 's/)$//')
+
+	check_libs $test $test_libs
+}
+
+l5_test()
+{
+	tests=$(find $(dirname "$test") -type f -name "*.mk")
+	test_libs=$(grep "^IOURING_EXTRA_LIBS +\?=" $tests | \
+			cut -d "=" -f 2)
+
+	check_libs $test $test_libs
+}
 
 check_libs()
 {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kselftest_harness.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kselftest_harness.h
@@ -244,7 +244,7 @@
 
 /**
  * FIXTURE_SETUP() - Prepares the setup function for the fixture.
- * *_metadata* is included so that EXPECT_* and ASSERT_* work correctly.
+ * *_metadata* is included so that EXPECT_*, ASSERT_* etc. work correctly.
  *
  * @fixture_name: fixture name
  *
@@ -270,7 +270,7 @@
 
 /**
  * FIXTURE_TEARDOWN()
- * *_metadata* is included so that EXPECT_* and ASSERT_* work correctly.
+ * *_metadata* is included so that EXPECT_*, ASSERT_* etc. work correctly.
  *
  * @fixture_name: fixture name
  *
@@ -383,7 +383,7 @@
 		memset(&self, 0, sizeof(FIXTURE_DATA(fixture_name))); \
 		fixture_name##_setup(_metadata, &self, variant->data); \
 		/* Let setup failure terminate early. */ \
-		if (!_metadata->passed) \
+		if (!_metadata->passed || _metadata->skip) \
 			return; \
 		fixture_name##_##test_name(_metadata, &self, variant->data); \
 		fixture_name##_teardown(_metadata, &self); \
@@ -671,7 +671,9 @@
 #define EXPECT_STRNE(expected, seen) \
 	__EXPECT_STR(expected, seen, !=, 0)
 
+#ifndef ARRAY_SIZE
 #define ARRAY_SIZE(a)	(sizeof(a) / sizeof(a[0]))
+#endif
 
 /* Support an optional handler after and ASSERT_* or EXPECT_*.  The approach is
  * not thread-safe, but it should be fine in most sane test scenarios.
@@ -699,33 +701,33 @@
 		/* Report with actual signedness to avoid weird output. */ \
 		switch (is_signed_type(__exp) * 2 + is_signed_type(__seen)) { \
 		case 0: { \
-			unsigned long long __exp_print = (uintptr_t)__exp; \
-			unsigned long long __seen_print = (uintptr_t)__seen; \
-			__TH_LOG("Expected %s (%llu) %s %s (%llu)", \
+			uintmax_t __exp_print = (uintmax_t)__exp; \
+			uintmax_t __seen_print = (uintmax_t)__seen; \
+			__TH_LOG("Expected %s (%ju) %s %s (%ju)", \
 				 _expected_str, __exp_print, #_t, \
 				 _seen_str, __seen_print); \
 			break; \
 			} \
 		case 1: { \
-			unsigned long long __exp_print = (uintptr_t)__exp; \
-			long long __seen_print = (intptr_t)__seen; \
-			__TH_LOG("Expected %s (%llu) %s %s (%lld)", \
+			uintmax_t __exp_print = (uintmax_t)__exp; \
+			intmax_t  __seen_print = (intmax_t)__seen; \
+			__TH_LOG("Expected %s (%ju) %s %s (%jd)", \
 				 _expected_str, __exp_print, #_t, \
 				 _seen_str, __seen_print); \
 			break; \
 			} \
 		case 2: { \
-			long long __exp_print = (intptr_t)__exp; \
-			unsigned long long __seen_print = (uintptr_t)__seen; \
-			__TH_LOG("Expected %s (%lld) %s %s (%llu)", \
+			intmax_t  __exp_print = (intmax_t)__exp; \
+			uintmax_t __seen_print = (uintmax_t)__seen; \
+			__TH_LOG("Expected %s (%jd) %s %s (%ju)", \
 				 _expected_str, __exp_print, #_t, \
 				 _seen_str, __seen_print); \
 			break; \
 			} \
 		case 3: { \
-			long long __exp_print = (intptr_t)__exp; \
-			long long __seen_print = (intptr_t)__seen; \
-			__TH_LOG("Expected %s (%lld) %s %s (%lld)", \
+			intmax_t  __exp_print = (intmax_t)__exp; \
+			intmax_t  __seen_print = (intmax_t)__seen; \
+			__TH_LOG("Expected %s (%jd) %s %s (%jd)", \
 				 _expected_str, __exp_print, #_t, \
 				 _seen_str, __seen_print); \
 			break; \
@@ -875,7 +877,8 @@
 	}
 
 	t->timed_out = true;
-	kill(t->pid, SIGKILL);
+	// signal process group
+	kill(-(t->pid), SIGKILL);
 }
 
 void __wait_for_test(struct __test_metadata *t)
@@ -913,7 +916,11 @@
 		fprintf(TH_LOG_STREAM,
 			"# %s: Test terminated by timeout\n", t->name);
 	} else if (WIFEXITED(status)) {
-		if (t->termsig != -1) {
+		if (WEXITSTATUS(status) == 255) {
+			/* SKIP */
+			t->passed = 1;
+			t->skip = 1;
+		} else if (t->termsig != -1) {
 			t->passed = 0;
 			fprintf(TH_LOG_STREAM,
 				"# %s: Test exited normally instead of by signal (code: %d)\n",
@@ -925,11 +932,6 @@
 			case 0:
 				t->passed = 1;
 				break;
-			/* SKIP */
-			case 255:
-				t->passed = 1;
-				t->skip = 1;
-				break;
 			/* Other failure, assume step report. */
 			default:
 				t->passed = 0;
@@ -969,7 +971,7 @@
 	t->passed = 1;
 	t->skip = 0;
 	t->trigger = 0;
-	t->step = 0;
+	t->step = 1;
 	t->no_print = 0;
 	memset(t->results->reason, 0, sizeof(t->results->reason));
 
@@ -985,6 +987,7 @@
 		ksft_print_msg("ERROR SPAWNING TEST CHILD\n");
 		t->passed = 0;
 	} else if (t->pid == 0) {
+		setpgrp();
 		t->fn(t, variant);
 		if (t->skip)
 			_exit(255);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/Makefile
@@ -103,6 +103,7 @@
 TEST_GEN_PROGS_s390x = s390x/memop
 TEST_GEN_PROGS_s390x += s390x/resets
 TEST_GEN_PROGS_s390x += s390x/sync_regs_test
+TEST_GEN_PROGS_s390x += s390x/tprot
 TEST_GEN_PROGS_s390x += demand_paging_test
 TEST_GEN_PROGS_s390x += dirty_log_test
 TEST_GEN_PROGS_s390x += kvm_create_max_vcpus
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/include/kvm_util.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/include/kvm_util.h
@@ -309,6 +309,7 @@
 
 unsigned int vm_get_page_size(struct kvm_vm *vm);
 unsigned int vm_get_page_shift(struct kvm_vm *vm);
+unsigned long vm_compute_max_gfn(struct kvm_vm *vm);
 uint64_t vm_get_max_gfn(struct kvm_vm *vm);
 int vm_get_fd(struct kvm_vm *vm);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/include/x86_64/processor.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/include/x86_64/processor.h
@@ -58,6 +58,21 @@
 /* CPUID.0x8000_0001.EDX */
 #define CPUID_GBPAGES		(1ul << 26)
 
+/* Page table bitfield declarations */
+#define PTE_PRESENT_MASK        BIT_ULL(0)
+#define PTE_WRITABLE_MASK       BIT_ULL(1)
+#define PTE_USER_MASK           BIT_ULL(2)
+#define PTE_ACCESSED_MASK       BIT_ULL(5)
+#define PTE_DIRTY_MASK          BIT_ULL(6)
+#define PTE_LARGE_MASK          BIT_ULL(7)
+#define PTE_GLOBAL_MASK         BIT_ULL(8)
+#define PTE_NX_MASK             BIT_ULL(63)
+
+#define PAGE_SHIFT		12
+
+#define PHYSICAL_PAGE_MASK      GENMASK_ULL(51, 12)
+#define PTE_GET_PFN(pte)        (((pte) & PHYSICAL_PAGE_MASK) >> PAGE_SHIFT)
+
 /* General Registers in 64-Bit Mode */
 struct gpr64_regs {
 	u64 rax;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/kvm_create_max_vcpus.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/kvm_create_max_vcpus.c
@@ -12,6 +12,7 @@
 #include <stdio.h>
 #include <stdlib.h>
 #include <string.h>
+#include <sys/resource.h>
 
 #include "test_util.h"
 
@@ -40,11 +41,40 @@
 {
 	int kvm_max_vcpu_id = kvm_check_cap(KVM_CAP_MAX_VCPU_ID);
 	int kvm_max_vcpus = kvm_check_cap(KVM_CAP_MAX_VCPUS);
+	/*
+	 * Number of file descriptors reqired, KVM_CAP_MAX_VCPUS for vCPU fds +
+	 * an arbitrary number for everything else.
+	 */
+	int nr_fds_wanted = kvm_max_vcpus + 100;
+	struct rlimit rl;
 
 	pr_info("KVM_CAP_MAX_VCPU_ID: %d\n", kvm_max_vcpu_id);
 	pr_info("KVM_CAP_MAX_VCPUS: %d\n", kvm_max_vcpus);
 
 	/*
+	 * Check that we're allowed to open nr_fds_wanted file descriptors and
+	 * try raising the limits if needed.
+	 */
+	TEST_ASSERT(!getrlimit(RLIMIT_NOFILE, &rl), "getrlimit() failed!");
+
+	if (rl.rlim_cur < nr_fds_wanted) {
+		rl.rlim_cur = nr_fds_wanted;
+		if (rl.rlim_max < nr_fds_wanted) {
+			int old_rlim_max = rl.rlim_max;
+			rl.rlim_max = nr_fds_wanted;
+
+			int r = setrlimit(RLIMIT_NOFILE, &rl);
+			if (r < 0) {
+				printf("RLIMIT_NOFILE hard limit is too low (%d, wanted %d)\n",
+				       old_rlim_max, nr_fds_wanted);
+				exit(KSFT_SKIP);
+			}
+		} else {
+			TEST_ASSERT(!setrlimit(RLIMIT_NOFILE, &rl), "setrlimit() failed!");
+		}
+	}
+
+	/*
 	 * Upstream KVM prior to 4.8 does not support KVM_CAP_MAX_VCPU_ID.
 	 * Userspace is supposed to use KVM_CAP_MAX_VCPUS as the maximum ID
 	 * in this case.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/kvm_page_table_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/kvm_page_table_test.c
@@ -278,7 +278,7 @@
 	else
 		guest_test_phys_mem = p->phys_offset;
 #ifdef __s390x__
-	alignment = max(0x100000, alignment);
+	alignment = max(0x100000UL, alignment);
 #endif
 	guest_test_phys_mem &= ~(alignment - 1);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/lib/aarch64/ucall.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/lib/aarch64/ucall.c
@@ -73,20 +73,19 @@
 
 void ucall(uint64_t cmd, int nargs, ...)
 {
-	struct ucall uc = {
-		.cmd = cmd,
-	};
+	struct ucall uc = {};
 	va_list va;
 	int i;
 
+	WRITE_ONCE(uc.cmd, cmd);
 	nargs = nargs <= UCALL_MAX_ARGS ? nargs : UCALL_MAX_ARGS;
 
 	va_start(va, nargs);
 	for (i = 0; i < nargs; ++i)
-		uc.args[i] = va_arg(va, uint64_t);
+		WRITE_ONCE(uc.args[i], va_arg(va, uint64_t));
 	va_end(va);
 
-	*ucall_exit_mmio_addr = (vm_vaddr_t)&uc;
+	WRITE_ONCE(*ucall_exit_mmio_addr, (vm_vaddr_t)&uc);
 }
 
 uint64_t get_ucall(struct kvm_vm *vm, uint32_t vcpu_id, struct ucall *uc)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/lib/kvm_util.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/lib/kvm_util.c
@@ -307,7 +307,7 @@
 		(1ULL << (vm->va_bits - 1)) >> vm->page_shift);
 
 	/* Limit physical addresses to PA-bits. */
-	vm->max_gfn = ((1ULL << vm->pa_bits) >> vm->page_shift) - 1;
+	vm->max_gfn = vm_compute_max_gfn(vm);
 
 	/* Allocate and setup memory for guest. */
 	vm->vpages_mapped = sparsebit_alloc();
@@ -2282,6 +2282,11 @@
 	return vm->page_shift;
 }
 
+unsigned long __attribute__((weak)) vm_compute_max_gfn(struct kvm_vm *vm)
+{
+	return ((1ULL << vm->pa_bits) >> vm->page_shift) - 1;
+}
+
 uint64_t vm_get_max_gfn(struct kvm_vm *vm)
 {
 	return vm->max_gfn;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/lib/x86_64/processor.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/lib/x86_64/processor.c
@@ -19,38 +19,6 @@
 
 vm_vaddr_t exception_handlers;
 
-/* Virtual translation table structure declarations */
-struct pageUpperEntry {
-	uint64_t present:1;
-	uint64_t writable:1;
-	uint64_t user:1;
-	uint64_t write_through:1;
-	uint64_t cache_disable:1;
-	uint64_t accessed:1;
-	uint64_t ignored_06:1;
-	uint64_t page_size:1;
-	uint64_t ignored_11_08:4;
-	uint64_t pfn:40;
-	uint64_t ignored_62_52:11;
-	uint64_t execute_disable:1;
-};
-
-struct pageTableEntry {
-	uint64_t present:1;
-	uint64_t writable:1;
-	uint64_t user:1;
-	uint64_t write_through:1;
-	uint64_t cache_disable:1;
-	uint64_t accessed:1;
-	uint64_t dirty:1;
-	uint64_t reserved_07:1;
-	uint64_t global:1;
-	uint64_t ignored_11_09:3;
-	uint64_t pfn:40;
-	uint64_t ignored_62_52:11;
-	uint64_t execute_disable:1;
-};
-
 void regs_dump(FILE *stream, struct kvm_regs *regs,
 	       uint8_t indent)
 {
@@ -195,23 +163,21 @@
 	return &page_table[index];
 }
 
-static struct pageUpperEntry *virt_create_upper_pte(struct kvm_vm *vm,
-						    uint64_t pt_pfn,
-						    uint64_t vaddr,
-						    uint64_t paddr,
-						    int level,
-						    enum x86_page_size page_size)
-{
-	struct pageUpperEntry *pte = virt_get_pte(vm, pt_pfn, vaddr, level);
-
-	if (!pte->present) {
-		pte->writable = true;
-		pte->present = true;
-		pte->page_size = (level == page_size);
-		if (pte->page_size)
-			pte->pfn = paddr >> vm->page_shift;
+static uint64_t *virt_create_upper_pte(struct kvm_vm *vm,
+				       uint64_t pt_pfn,
+				       uint64_t vaddr,
+				       uint64_t paddr,
+				       int level,
+				       enum x86_page_size page_size)
+{
+	uint64_t *pte = virt_get_pte(vm, pt_pfn, vaddr, level);
+
+	if (!(*pte & PTE_PRESENT_MASK)) {
+		*pte = PTE_PRESENT_MASK | PTE_WRITABLE_MASK;
+		if (level == page_size)
+			*pte |= PTE_LARGE_MASK | (paddr & PHYSICAL_PAGE_MASK);
 		else
-			pte->pfn = vm_alloc_page_table(vm) >> vm->page_shift;
+			*pte |= vm_alloc_page_table(vm) & PHYSICAL_PAGE_MASK;
 	} else {
 		/*
 		 * Entry already present.  Assert that the caller doesn't want
@@ -221,7 +187,7 @@
 		TEST_ASSERT(level != page_size,
 			    "Cannot create hugepage at level: %u, vaddr: 0x%lx\n",
 			    page_size, vaddr);
-		TEST_ASSERT(!pte->page_size,
+		TEST_ASSERT(!(*pte & PTE_LARGE_MASK),
 			    "Cannot create page table at level: %u, vaddr: 0x%lx\n",
 			    level, vaddr);
 	}
@@ -232,8 +198,8 @@
 		   enum x86_page_size page_size)
 {
 	const uint64_t pg_size = 1ull << ((page_size * 9) + 12);
-	struct pageUpperEntry *pml4e, *pdpe, *pde;
-	struct pageTableEntry *pte;
+	uint64_t *pml4e, *pdpe, *pde;
+	uint64_t *pte;
 
 	TEST_ASSERT(vm->mode == VM_MODE_PXXV48_4K,
 		    "Unknown or unsupported guest mode, mode: 0x%x", vm->mode);
@@ -257,24 +223,22 @@
 	 */
 	pml4e = virt_create_upper_pte(vm, vm->pgd >> vm->page_shift,
 				      vaddr, paddr, 3, page_size);
-	if (pml4e->page_size)
+	if (*pml4e & PTE_LARGE_MASK)
 		return;
 
-	pdpe = virt_create_upper_pte(vm, pml4e->pfn, vaddr, paddr, 2, page_size);
-	if (pdpe->page_size)
+	pdpe = virt_create_upper_pte(vm, PTE_GET_PFN(*pml4e), vaddr, paddr, 2, page_size);
+	if (*pdpe & PTE_LARGE_MASK)
 		return;
 
-	pde = virt_create_upper_pte(vm, pdpe->pfn, vaddr, paddr, 1, page_size);
-	if (pde->page_size)
+	pde = virt_create_upper_pte(vm, PTE_GET_PFN(*pdpe), vaddr, paddr, 1, page_size);
+	if (*pde & PTE_LARGE_MASK)
 		return;
 
 	/* Fill in page table entry. */
-	pte = virt_get_pte(vm, pde->pfn, vaddr, 0);
-	TEST_ASSERT(!pte->present,
+	pte = virt_get_pte(vm, PTE_GET_PFN(*pde), vaddr, 0);
+	TEST_ASSERT(!(*pte & PTE_PRESENT_MASK),
 		    "PTE already present for 4k page at vaddr: 0x%lx\n", vaddr);
-	pte->pfn = paddr >> vm->page_shift;
-	pte->writable = true;
-	pte->present = 1;
+	*pte = PTE_PRESENT_MASK | PTE_WRITABLE_MASK | (paddr & PHYSICAL_PAGE_MASK);
 }
 
 void virt_pg_map(struct kvm_vm *vm, uint64_t vaddr, uint64_t paddr)
@@ -282,12 +246,12 @@
 	__virt_pg_map(vm, vaddr, paddr, X86_PAGE_SIZE_4K);
 }
 
-static struct pageTableEntry *_vm_get_page_table_entry(struct kvm_vm *vm, int vcpuid,
+static uint64_t *_vm_get_page_table_entry(struct kvm_vm *vm, int vcpuid,
 						       uint64_t vaddr)
 {
 	uint16_t index[4];
-	struct pageUpperEntry *pml4e, *pdpe, *pde;
-	struct pageTableEntry *pte;
+	uint64_t *pml4e, *pdpe, *pde;
+	uint64_t *pte;
 	struct kvm_cpuid_entry2 *entry;
 	struct kvm_sregs sregs;
 	int max_phy_addr;
@@ -329,30 +293,29 @@
 	index[3] = (vaddr >> 39) & 0x1ffu;
 
 	pml4e = addr_gpa2hva(vm, vm->pgd);
-	TEST_ASSERT(pml4e[index[3]].present,
+	TEST_ASSERT(pml4e[index[3]] & PTE_PRESENT_MASK,
 		"Expected pml4e to be present for gva: 0x%08lx", vaddr);
-	TEST_ASSERT((*(uint64_t*)(&pml4e[index[3]]) &
-		(rsvd_mask | (1ull << 7))) == 0,
+	TEST_ASSERT((pml4e[index[3]] & (rsvd_mask | PTE_LARGE_MASK)) == 0,
 		"Unexpected reserved bits set.");
 
-	pdpe = addr_gpa2hva(vm, pml4e[index[3]].pfn * vm->page_size);
-	TEST_ASSERT(pdpe[index[2]].present,
+	pdpe = addr_gpa2hva(vm, PTE_GET_PFN(pml4e[index[3]]) * vm->page_size);
+	TEST_ASSERT(pdpe[index[2]] & PTE_PRESENT_MASK,
 		"Expected pdpe to be present for gva: 0x%08lx", vaddr);
-	TEST_ASSERT(pdpe[index[2]].page_size == 0,
+	TEST_ASSERT(!(pdpe[index[2]] & PTE_LARGE_MASK),
 		"Expected pdpe to map a pde not a 1-GByte page.");
-	TEST_ASSERT((*(uint64_t*)(&pdpe[index[2]]) & rsvd_mask) == 0,
+	TEST_ASSERT((pdpe[index[2]] & rsvd_mask) == 0,
 		"Unexpected reserved bits set.");
 
-	pde = addr_gpa2hva(vm, pdpe[index[2]].pfn * vm->page_size);
-	TEST_ASSERT(pde[index[1]].present,
+	pde = addr_gpa2hva(vm, PTE_GET_PFN(pdpe[index[2]]) * vm->page_size);
+	TEST_ASSERT(pde[index[1]] & PTE_PRESENT_MASK,
 		"Expected pde to be present for gva: 0x%08lx", vaddr);
-	TEST_ASSERT(pde[index[1]].page_size == 0,
+	TEST_ASSERT(!(pde[index[1]] & PTE_LARGE_MASK),
 		"Expected pde to map a pte not a 2-MByte page.");
-	TEST_ASSERT((*(uint64_t*)(&pde[index[1]]) & rsvd_mask) == 0,
+	TEST_ASSERT((pde[index[1]] & rsvd_mask) == 0,
 		"Unexpected reserved bits set.");
 
-	pte = addr_gpa2hva(vm, pde[index[1]].pfn * vm->page_size);
-	TEST_ASSERT(pte[index[0]].present,
+	pte = addr_gpa2hva(vm, PTE_GET_PFN(pde[index[1]]) * vm->page_size);
+	TEST_ASSERT(pte[index[0]] & PTE_PRESENT_MASK,
 		"Expected pte to be present for gva: 0x%08lx", vaddr);
 
 	return &pte[index[0]];
@@ -360,7 +323,7 @@
 
 uint64_t vm_get_page_table_entry(struct kvm_vm *vm, int vcpuid, uint64_t vaddr)
 {
-	struct pageTableEntry *pte = _vm_get_page_table_entry(vm, vcpuid, vaddr);
+	uint64_t *pte = _vm_get_page_table_entry(vm, vcpuid, vaddr);
 
 	return *(uint64_t *)pte;
 }
@@ -368,18 +331,17 @@
 void vm_set_page_table_entry(struct kvm_vm *vm, int vcpuid, uint64_t vaddr,
 			     uint64_t pte)
 {
-	struct pageTableEntry *new_pte = _vm_get_page_table_entry(vm, vcpuid,
-								  vaddr);
+	uint64_t *new_pte = _vm_get_page_table_entry(vm, vcpuid, vaddr);
 
 	*(uint64_t *)new_pte = pte;
 }
 
 void virt_dump(FILE *stream, struct kvm_vm *vm, uint8_t indent)
 {
-	struct pageUpperEntry *pml4e, *pml4e_start;
-	struct pageUpperEntry *pdpe, *pdpe_start;
-	struct pageUpperEntry *pde, *pde_start;
-	struct pageTableEntry *pte, *pte_start;
+	uint64_t *pml4e, *pml4e_start;
+	uint64_t *pdpe, *pdpe_start;
+	uint64_t *pde, *pde_start;
+	uint64_t *pte, *pte_start;
 
 	if (!vm->pgd_created)
 		return;
@@ -389,58 +351,58 @@
 	fprintf(stream, "%*s      index hvaddr         gpaddr         "
 		"addr         w exec dirty\n",
 		indent, "");
-	pml4e_start = (struct pageUpperEntry *) addr_gpa2hva(vm, vm->pgd);
+	pml4e_start = (uint64_t *) addr_gpa2hva(vm, vm->pgd);
 	for (uint16_t n1 = 0; n1 <= 0x1ffu; n1++) {
 		pml4e = &pml4e_start[n1];
-		if (!pml4e->present)
+		if (!(*pml4e & PTE_PRESENT_MASK))
 			continue;
-		fprintf(stream, "%*spml4e 0x%-3zx %p 0x%-12lx 0x%-10lx %u "
+		fprintf(stream, "%*spml4e 0x%-3zx %p 0x%-12lx 0x%-10llx %u "
 			" %u\n",
 			indent, "",
 			pml4e - pml4e_start, pml4e,
-			addr_hva2gpa(vm, pml4e), (uint64_t) pml4e->pfn,
-			pml4e->writable, pml4e->execute_disable);
+			addr_hva2gpa(vm, pml4e), PTE_GET_PFN(*pml4e),
+			!!(*pml4e & PTE_WRITABLE_MASK), !!(*pml4e & PTE_NX_MASK));
 
-		pdpe_start = addr_gpa2hva(vm, pml4e->pfn * vm->page_size);
+		pdpe_start = addr_gpa2hva(vm, *pml4e & PHYSICAL_PAGE_MASK);
 		for (uint16_t n2 = 0; n2 <= 0x1ffu; n2++) {
 			pdpe = &pdpe_start[n2];
-			if (!pdpe->present)
+			if (!(*pdpe & PTE_PRESENT_MASK))
 				continue;
-			fprintf(stream, "%*spdpe  0x%-3zx %p 0x%-12lx 0x%-10lx "
+			fprintf(stream, "%*spdpe  0x%-3zx %p 0x%-12lx 0x%-10llx "
 				"%u  %u\n",
 				indent, "",
 				pdpe - pdpe_start, pdpe,
 				addr_hva2gpa(vm, pdpe),
-				(uint64_t) pdpe->pfn, pdpe->writable,
-				pdpe->execute_disable);
+				PTE_GET_PFN(*pdpe), !!(*pdpe & PTE_WRITABLE_MASK),
+				!!(*pdpe & PTE_NX_MASK));
 
-			pde_start = addr_gpa2hva(vm, pdpe->pfn * vm->page_size);
+			pde_start = addr_gpa2hva(vm, *pdpe & PHYSICAL_PAGE_MASK);
 			for (uint16_t n3 = 0; n3 <= 0x1ffu; n3++) {
 				pde = &pde_start[n3];
-				if (!pde->present)
+				if (!(*pde & PTE_PRESENT_MASK))
 					continue;
 				fprintf(stream, "%*spde   0x%-3zx %p "
-					"0x%-12lx 0x%-10lx %u  %u\n",
+					"0x%-12lx 0x%-10llx %u  %u\n",
 					indent, "", pde - pde_start, pde,
 					addr_hva2gpa(vm, pde),
-					(uint64_t) pde->pfn, pde->writable,
-					pde->execute_disable);
+					PTE_GET_PFN(*pde), !!(*pde & PTE_WRITABLE_MASK),
+					!!(*pde & PTE_NX_MASK));
 
-				pte_start = addr_gpa2hva(vm, pde->pfn * vm->page_size);
+				pte_start = addr_gpa2hva(vm, *pde & PHYSICAL_PAGE_MASK);
 				for (uint16_t n4 = 0; n4 <= 0x1ffu; n4++) {
 					pte = &pte_start[n4];
-					if (!pte->present)
+					if (!(*pte & PTE_PRESENT_MASK))
 						continue;
 					fprintf(stream, "%*spte   0x%-3zx %p "
-						"0x%-12lx 0x%-10lx %u  %u "
+						"0x%-12lx 0x%-10llx %u  %u "
 						"    %u    0x%-10lx\n",
 						indent, "",
 						pte - pte_start, pte,
 						addr_hva2gpa(vm, pte),
-						(uint64_t) pte->pfn,
-						pte->writable,
-						pte->execute_disable,
-						pte->dirty,
+						PTE_GET_PFN(*pte),
+						!!(*pte & PTE_WRITABLE_MASK),
+						!!(*pte & PTE_NX_MASK),
+						!!(*pte & PTE_DIRTY_MASK),
 						((uint64_t) n1 << 27)
 							| ((uint64_t) n2 << 18)
 							| ((uint64_t) n3 << 9)
@@ -558,8 +520,8 @@
 vm_paddr_t addr_gva2gpa(struct kvm_vm *vm, vm_vaddr_t gva)
 {
 	uint16_t index[4];
-	struct pageUpperEntry *pml4e, *pdpe, *pde;
-	struct pageTableEntry *pte;
+	uint64_t *pml4e, *pdpe, *pde;
+	uint64_t *pte;
 
 	TEST_ASSERT(vm->mode == VM_MODE_PXXV48_4K, "Attempt to use "
 		"unknown or unsupported guest mode, mode: 0x%x", vm->mode);
@@ -572,22 +534,22 @@
 	if (!vm->pgd_created)
 		goto unmapped_gva;
 	pml4e = addr_gpa2hva(vm, vm->pgd);
-	if (!pml4e[index[3]].present)
+	if (!(pml4e[index[3]] & PTE_PRESENT_MASK))
 		goto unmapped_gva;
 
-	pdpe = addr_gpa2hva(vm, pml4e[index[3]].pfn * vm->page_size);
-	if (!pdpe[index[2]].present)
+	pdpe = addr_gpa2hva(vm, PTE_GET_PFN(pml4e[index[3]]) * vm->page_size);
+	if (!(pdpe[index[2]] & PTE_PRESENT_MASK))
 		goto unmapped_gva;
 
-	pde = addr_gpa2hva(vm, pdpe[index[2]].pfn * vm->page_size);
-	if (!pde[index[1]].present)
+	pde = addr_gpa2hva(vm, PTE_GET_PFN(pdpe[index[2]]) * vm->page_size);
+	if (!(pde[index[1]] & PTE_PRESENT_MASK))
 		goto unmapped_gva;
 
-	pte = addr_gpa2hva(vm, pde[index[1]].pfn * vm->page_size);
-	if (!pte[index[0]].present)
+	pte = addr_gpa2hva(vm, PTE_GET_PFN(pde[index[1]]) * vm->page_size);
+	if (!(pte[index[0]] & PTE_PRESENT_MASK))
 		goto unmapped_gva;
 
-	return (pte[index[0]].pfn * vm->page_size) + (gva & 0xfffu);
+	return (PTE_GET_PFN(pte[index[0]]) * vm->page_size) + (gva & 0xfffu);
 
 unmapped_gva:
 	TEST_FAIL("No mapping for vm virtual address, gva: 0x%lx", gva);
@@ -1364,7 +1326,7 @@
 
 	asm volatile("vmcall"
 		     : "=a"(r)
-		     : "b"(a0), "c"(a1), "d"(a2), "S"(a3));
+		     : "a"(nr), "b"(a0), "c"(a1), "d"(a2), "S"(a3));
 	return r;
 }
 
@@ -1433,3 +1395,71 @@
 
 	return cpuid;
 }
+
+#define X86EMUL_CPUID_VENDOR_AuthenticAMD_ebx 0x68747541
+#define X86EMUL_CPUID_VENDOR_AuthenticAMD_ecx 0x444d4163
+#define X86EMUL_CPUID_VENDOR_AuthenticAMD_edx 0x69746e65
+
+static inline unsigned x86_family(unsigned int eax)
+{
+        unsigned int x86;
+
+        x86 = (eax >> 8) & 0xf;
+
+        if (x86 == 0xf)
+                x86 += (eax >> 20) & 0xff;
+
+        return x86;
+}
+
+unsigned long vm_compute_max_gfn(struct kvm_vm *vm)
+{
+	const unsigned long num_ht_pages = 12 << (30 - vm->page_shift); /* 12 GiB */
+	unsigned long ht_gfn, max_gfn, max_pfn;
+	uint32_t eax, ebx, ecx, edx, max_ext_leaf;
+
+	max_gfn = (1ULL << (vm->pa_bits - vm->page_shift)) - 1;
+
+	/* Avoid reserved HyperTransport region on AMD processors.  */
+	eax = ecx = 0;
+	cpuid(&eax, &ebx, &ecx, &edx);
+	if (ebx != X86EMUL_CPUID_VENDOR_AuthenticAMD_ebx ||
+	    ecx != X86EMUL_CPUID_VENDOR_AuthenticAMD_ecx ||
+	    edx != X86EMUL_CPUID_VENDOR_AuthenticAMD_edx)
+		return max_gfn;
+
+	/* On parts with <40 physical address bits, the area is fully hidden */
+	if (vm->pa_bits < 40)
+		return max_gfn;
+
+	/* Before family 17h, the HyperTransport area is just below 1T.  */
+	ht_gfn = (1 << 28) - num_ht_pages;
+	eax = 1;
+	cpuid(&eax, &ebx, &ecx, &edx);
+	if (x86_family(eax) < 0x17)
+		goto done;
+
+	/*
+	 * Otherwise it's at the top of the physical address space, possibly
+	 * reduced due to SME by bits 11:6 of CPUID[0x8000001f].EBX.  Use
+	 * the old conservative value if MAXPHYADDR is not enumerated.
+	 */
+	eax = 0x80000000;
+	cpuid(&eax, &ebx, &ecx, &edx);
+	max_ext_leaf = eax;
+	if (max_ext_leaf < 0x80000008)
+		goto done;
+
+	eax = 0x80000008;
+	cpuid(&eax, &ebx, &ecx, &edx);
+	max_pfn = (1ULL << ((eax & 0xff) - vm->page_shift)) - 1;
+	if (max_ext_leaf >= 0x8000001f) {
+		eax = 0x8000001f;
+		cpuid(&eax, &ebx, &ecx, &edx);
+		max_pfn >>= (ebx >> 6) & 0x3f;
+	}
+
+	ht_gfn = max_pfn - num_ht_pages;
+done:
+	return min(max_gfn, ht_gfn - 1);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/lib/x86_64/svm.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/lib/x86_64/svm.c
@@ -54,6 +54,18 @@
 	seg->base = base;
 }
 
+/*
+ * Avoid using memset to clear the vmcb, since libc may not be
+ * available in L1 (and, even if it is, features that libc memset may
+ * want to use, like AVX, may not be enabled).
+ */
+static void clear_vmcb(struct vmcb *vmcb)
+{
+	int n = sizeof(*vmcb) / sizeof(u32);
+
+	asm volatile ("rep stosl" : "+c"(n), "+D"(vmcb) : "a"(0) : "memory");
+}
+
 void generic_svm_setup(struct svm_test_data *svm, void *guest_rip, void *guest_rsp)
 {
 	struct vmcb *vmcb = svm->vmcb;
@@ -70,7 +82,7 @@
 	wrmsr(MSR_EFER, efer | EFER_SVME);
 	wrmsr(MSR_VM_HSAVE_PA, svm->save_area_gpa);
 
-	memset(vmcb, 0, sizeof(*vmcb));
+	clear_vmcb(vmcb);
 	asm volatile ("vmsave %0\n\t" : : "a" (vmcb_gpa) : "memory");
 	vmcb_set_seg(&save->es, get_es(), 0, -1U, data_seg_attr);
 	vmcb_set_seg(&save->cs, get_cs(), 0, -1U, code_seg_attr);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/memslot_modification_stress_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/memslot_modification_stress_test.c
@@ -72,7 +72,7 @@
 static void add_remove_memslot(struct kvm_vm *vm, useconds_t delay,
 			       uint64_t nr_modifications)
 {
-	const uint64_t pages = 1;
+	uint64_t pages = max_t(int, vm_get_page_size(vm), getpagesize()) / vm_get_page_size(vm);
 	uint64_t gpa;
 	int i;
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/rseq_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/rseq_test.c
@@ -82,8 +82,9 @@
 	return cpu;
 }
 
-static void *migration_worker(void *ign)
+static void *migration_worker(void *__rseq_tid)
 {
+	pid_t rseq_tid = (pid_t)(unsigned long)__rseq_tid;
 	cpu_set_t allowed_mask;
 	int r, i, cpu;
 
@@ -106,7 +107,7 @@
 		 * stable, i.e. while changing affinity is in-progress.
 		 */
 		smp_wmb();
-		r = sched_setaffinity(0, sizeof(allowed_mask), &allowed_mask);
+		r = sched_setaffinity(rseq_tid, sizeof(allowed_mask), &allowed_mask);
 		TEST_ASSERT(!r, "sched_setaffinity failed, errno = %d (%s)",
 			    errno, strerror(errno));
 		smp_wmb();
@@ -231,7 +232,8 @@
 	vm = vm_create_default(VCPU_ID, 0, guest_code);
 	ucall_init(vm, NULL);
 
-	pthread_create(&migration_thread, NULL, migration_worker, 0);
+	pthread_create(&migration_thread, NULL, migration_worker,
+		       (void *)(unsigned long)syscall(SYS_gettid));
 
 	for (i = 0; !done; i++) {
 		vcpu_run(vm, VCPU_ID);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/s390x/tprot.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/s390x/tprot.c
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Test TEST PROTECTION emulation.
+ *
+ * Copyright IBM Corp. 2021
+ */
+
+#include <sys/mman.h>
+#include "test_util.h"
+#include "kvm_util.h"
+
+#define PAGE_SHIFT 12
+#define PAGE_SIZE (1 << PAGE_SHIFT)
+#define CR0_FETCH_PROTECTION_OVERRIDE	(1UL << (63 - 38))
+#define CR0_STORAGE_PROTECTION_OVERRIDE	(1UL << (63 - 39))
+
+#define VCPU_ID 1
+
+static __aligned(PAGE_SIZE) uint8_t pages[2][PAGE_SIZE];
+static uint8_t *const page_store_prot = pages[0];
+static uint8_t *const page_fetch_prot = pages[1];
+
+/* Nonzero return value indicates that address not mapped */
+static int set_storage_key(void *addr, uint8_t key)
+{
+	int not_mapped = 0;
+
+	asm volatile (
+		       "lra	%[addr], 0(0,%[addr])\n"
+		"	jz	0f\n"
+		"	llill	%[not_mapped],1\n"
+		"	j	1f\n"
+		"0:	sske	%[key], %[addr]\n"
+		"1:"
+		: [addr] "+&a" (addr), [not_mapped] "+r" (not_mapped)
+		: [key] "r" (key)
+		: "cc"
+	);
+	return -not_mapped;
+}
+
+enum permission {
+	READ_WRITE = 0,
+	READ = 1,
+	RW_PROTECTED = 2,
+	TRANSL_UNAVAIL = 3,
+};
+
+static enum permission test_protection(void *addr, uint8_t key)
+{
+	uint64_t mask;
+
+	asm volatile (
+		       "tprot	%[addr], 0(%[key])\n"
+		"	ipm	%[mask]\n"
+		: [mask] "=r" (mask)
+		: [addr] "Q" (*(char *)addr),
+		  [key] "a" (key)
+		: "cc"
+	);
+
+	return (enum permission)(mask >> 28);
+}
+
+enum stage {
+	STAGE_END,
+	STAGE_INIT_SIMPLE,
+	TEST_SIMPLE,
+	STAGE_INIT_FETCH_PROT_OVERRIDE,
+	TEST_FETCH_PROT_OVERRIDE,
+	TEST_STORAGE_PROT_OVERRIDE,
+};
+
+struct test {
+	enum stage stage;
+	void *addr;
+	uint8_t key;
+	enum permission expected;
+} tests[] = {
+	/*
+	 * We perform each test in the array by executing TEST PROTECTION on
+	 * the specified addr with the specified key and checking if the returned
+	 * permissions match the expected value.
+	 * Both guest and host cooperate to set up the required test conditions.
+	 * A central condition is that the page targeted by addr has to be DAT
+	 * protected in the host mappings, in order for KVM to emulate the
+	 * TEST PROTECTION instruction.
+	 * Since the page tables are shared, the host uses mprotect to achieve
+	 * this.
+	 *
+	 * Test resulting in RW_PROTECTED/TRANSL_UNAVAIL will be interpreted
+	 * by SIE, not KVM, but there is no harm in testing them also.
+	 * See Enhanced Suppression-on-Protection Facilities in the
+	 * Interpretive-Execution Mode
+	 */
+	/*
+	 * guest: set storage key of page_store_prot to 1
+	 *        storage key of page_fetch_prot to 9 and enable
+	 *        protection for it
+	 * STAGE_INIT_SIMPLE
+	 * host: write protect both via mprotect
+	 */
+	/* access key 0 matches any storage key -> RW */
+	{ TEST_SIMPLE, page_store_prot, 0x00, READ_WRITE },
+	/* access key matches storage key -> RW */
+	{ TEST_SIMPLE, page_store_prot, 0x10, READ_WRITE },
+	/* mismatched keys, but no fetch protection -> RO */
+	{ TEST_SIMPLE, page_store_prot, 0x20, READ },
+	/* access key 0 matches any storage key -> RW */
+	{ TEST_SIMPLE, page_fetch_prot, 0x00, READ_WRITE },
+	/* access key matches storage key -> RW */
+	{ TEST_SIMPLE, page_fetch_prot, 0x90, READ_WRITE },
+	/* mismatched keys, fetch protection -> inaccessible */
+	{ TEST_SIMPLE, page_fetch_prot, 0x10, RW_PROTECTED },
+	/* page 0 not mapped yet -> translation not available */
+	{ TEST_SIMPLE, (void *)0x00, 0x10, TRANSL_UNAVAIL },
+	/*
+	 * host: try to map page 0
+	 * guest: set storage key of page 0 to 9 and enable fetch protection
+	 * STAGE_INIT_FETCH_PROT_OVERRIDE
+	 * host: write protect page 0
+	 *       enable fetch protection override
+	 */
+	/* mismatched keys, fetch protection, but override applies -> RO */
+	{ TEST_FETCH_PROT_OVERRIDE, (void *)0x00, 0x10, READ },
+	/* mismatched keys, fetch protection, override applies to 0-2048 only -> inaccessible */
+	{ TEST_FETCH_PROT_OVERRIDE, (void *)2049, 0x10, RW_PROTECTED },
+	/*
+	 * host: enable storage protection override
+	 */
+	/* mismatched keys, but override applies (storage key 9) -> RW */
+	{ TEST_STORAGE_PROT_OVERRIDE, page_fetch_prot, 0x10, READ_WRITE },
+	/* mismatched keys, no fetch protection, override doesn't apply -> RO */
+	{ TEST_STORAGE_PROT_OVERRIDE, page_store_prot, 0x20, READ },
+	/* mismatched keys, but override applies (storage key 9) -> RW */
+	{ TEST_STORAGE_PROT_OVERRIDE, (void *)2049, 0x10, READ_WRITE },
+	/* end marker */
+	{ STAGE_END, 0, 0, 0 },
+};
+
+static enum stage perform_next_stage(int *i, bool mapped_0)
+{
+	enum stage stage = tests[*i].stage;
+	enum permission result;
+	bool skip;
+
+	for (; tests[*i].stage == stage; (*i)++) {
+		/*
+		 * Some fetch protection override tests require that page 0
+		 * be mapped, however, when the hosts tries to map that page via
+		 * vm_vaddr_alloc, it may happen that some other page gets mapped
+		 * instead.
+		 * In order to skip these tests we detect this inside the guest
+		 */
+		skip = tests[*i].addr < (void *)4096 &&
+		       tests[*i].expected != TRANSL_UNAVAIL &&
+		       !mapped_0;
+		if (!skip) {
+			result = test_protection(tests[*i].addr, tests[*i].key);
+			GUEST_ASSERT_2(result == tests[*i].expected, *i, result);
+		}
+	}
+	return stage;
+}
+
+static void guest_code(void)
+{
+	bool mapped_0;
+	int i = 0;
+
+	GUEST_ASSERT_EQ(set_storage_key(page_store_prot, 0x10), 0);
+	GUEST_ASSERT_EQ(set_storage_key(page_fetch_prot, 0x98), 0);
+	GUEST_SYNC(STAGE_INIT_SIMPLE);
+	GUEST_SYNC(perform_next_stage(&i, false));
+
+	/* Fetch-protection override */
+	mapped_0 = !set_storage_key((void *)0, 0x98);
+	GUEST_SYNC(STAGE_INIT_FETCH_PROT_OVERRIDE);
+	GUEST_SYNC(perform_next_stage(&i, mapped_0));
+
+	/* Storage-protection override */
+	GUEST_SYNC(perform_next_stage(&i, mapped_0));
+}
+
+#define HOST_SYNC(vmp, stage)							\
+({										\
+	struct kvm_vm *__vm = (vmp);						\
+	struct ucall uc;							\
+	int __stage = (stage);							\
+										\
+	vcpu_run(__vm, VCPU_ID);						\
+	get_ucall(__vm, VCPU_ID, &uc);						\
+	if (uc.cmd == UCALL_ABORT) {						\
+		TEST_FAIL("line %lu: %s, hints: %lu, %lu", uc.args[1],		\
+			  (const char *)uc.args[0], uc.args[2], uc.args[3]);	\
+	}									\
+	ASSERT_EQ(uc.cmd, UCALL_SYNC);						\
+	ASSERT_EQ(uc.args[1], __stage);						\
+})
+
+int main(int argc, char *argv[])
+{
+	struct kvm_vm *vm;
+	struct kvm_run *run;
+	vm_vaddr_t guest_0_page;
+
+	vm = vm_create_default(VCPU_ID, 0, guest_code);
+	run = vcpu_state(vm, VCPU_ID);
+
+	HOST_SYNC(vm, STAGE_INIT_SIMPLE);
+	mprotect(addr_gva2hva(vm, (vm_vaddr_t)pages), PAGE_SIZE * 2, PROT_READ);
+	HOST_SYNC(vm, TEST_SIMPLE);
+
+	guest_0_page = vm_vaddr_alloc(vm, PAGE_SIZE, 0);
+	if (guest_0_page != 0)
+		print_skip("Did not allocate page at 0 for fetch protection override tests");
+	HOST_SYNC(vm, STAGE_INIT_FETCH_PROT_OVERRIDE);
+	if (guest_0_page == 0)
+		mprotect(addr_gva2hva(vm, (vm_vaddr_t)0), PAGE_SIZE, PROT_READ);
+	run->s.regs.crs[0] |= CR0_FETCH_PROTECTION_OVERRIDE;
+	run->kvm_dirty_regs = KVM_SYNC_CRS;
+	HOST_SYNC(vm, TEST_FETCH_PROT_OVERRIDE);
+
+	run->s.regs.crs[0] |= CR0_STORAGE_PROTECTION_OVERRIDE;
+	run->kvm_dirty_regs = KVM_SYNC_CRS;
+	HOST_SYNC(vm, TEST_STORAGE_PROT_OVERRIDE);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/x86_64/hyperv_clock.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/x86_64/hyperv_clock.c
@@ -44,7 +44,7 @@
 {
 	int i;
 
-	for (i = 0; i < 1000000; i++)
+	for (i = 0; i < 100000000; i++)
 		asm volatile("nop");
 }
 
@@ -56,12 +56,14 @@
 	tsc_freq = rdmsr(HV_X64_MSR_TSC_FREQUENCY);
 	GUEST_ASSERT(tsc_freq > 0);
 
-	/* First, check MSR-based clocksource */
+	/* For increased accuracy, take mean rdtsc() before and afrer rdmsr() */
 	r1 = rdtsc();
 	t1 = rdmsr(HV_X64_MSR_TIME_REF_COUNT);
+	r1 = (r1 + rdtsc()) / 2;
 	nop_loop();
 	r2 = rdtsc();
 	t2 = rdmsr(HV_X64_MSR_TIME_REF_COUNT);
+	r2 = (r2 + rdtsc()) / 2;
 
 	GUEST_ASSERT(r2 > r1 && t2 > t1);
 
@@ -181,12 +183,14 @@
 	tsc_freq = vcpu_get_msr(vm, VCPU_ID, HV_X64_MSR_TSC_FREQUENCY);
 	TEST_ASSERT(tsc_freq > 0, "TSC frequency must be nonzero");
 
-	/* First, check MSR-based clocksource */
+	/* For increased accuracy, take mean rdtsc() before and afrer ioctl */
 	r1 = rdtsc();
 	t1 = vcpu_get_msr(vm, VCPU_ID, HV_X64_MSR_TIME_REF_COUNT);
+	r1 = (r1 + rdtsc()) / 2;
 	nop_loop();
 	r2 = rdtsc();
 	t2 = vcpu_get_msr(vm, VCPU_ID, HV_X64_MSR_TIME_REF_COUNT);
+	r2 = (r2 + rdtsc()) / 2;
 
 	TEST_ASSERT(t2 > t1, "Time reference MSR is not monotonic (%ld <= %ld)", t1, t2);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/x86_64/mmio_warning_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/x86_64/mmio_warning_test.c
@@ -84,7 +84,7 @@
 	f = popen("dmesg | grep \"WARNING:\" | wc -l", "r");
 	if (fscanf(f, "%d", &warnings) < 1)
 		warnings = 0;
-	fclose(f);
+	pclose(f);
 
 	return warnings;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/kvm/x86_64/smm_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/kvm/x86_64/smm_test.c
@@ -105,7 +105,6 @@
 
 		if (cpu_has_svm()) {
 			run_guest(svm->vmcb, svm->vmcb_gpa);
-			svm->vmcb->save.rip += 3;
 			run_guest(svm->vmcb, svm->vmcb_gpa);
 		} else {
 			vmlaunch();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/landlock/base_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/landlock/base_test.c
@@ -9,6 +9,7 @@
 #define _GNU_SOURCE
 #include <errno.h>
 #include <fcntl.h>
+#include <linux/keyctl.h>
 #include <linux/landlock.h>
 #include <string.h>
 #include <sys/prctl.h>
@@ -18,10 +19,11 @@
 #include "common.h"
 
 #ifndef O_PATH
-#define O_PATH		010000000
+#define O_PATH 010000000
 #endif
 
-TEST(inconsistent_attr) {
+TEST(inconsistent_attr)
+{
 	const long page_size = sysconf(_SC_PAGESIZE);
 	char *const buf = malloc(page_size + 1);
 	struct landlock_ruleset_attr *const ruleset_attr = (void *)buf;
@@ -34,20 +36,26 @@
 	ASSERT_EQ(EINVAL, errno);
 	ASSERT_EQ(-1, landlock_create_ruleset(ruleset_attr, 1, 0));
 	ASSERT_EQ(EINVAL, errno);
+	ASSERT_EQ(-1, landlock_create_ruleset(ruleset_attr, 7, 0));
+	ASSERT_EQ(EINVAL, errno);
 
 	ASSERT_EQ(-1, landlock_create_ruleset(NULL, 1, 0));
 	/* The size if less than sizeof(struct landlock_attr_enforce). */
 	ASSERT_EQ(EFAULT, errno);
 
-	ASSERT_EQ(-1, landlock_create_ruleset(NULL,
-				sizeof(struct landlock_ruleset_attr), 0));
+	ASSERT_EQ(-1, landlock_create_ruleset(
+			      NULL, sizeof(struct landlock_ruleset_attr), 0));
 	ASSERT_EQ(EFAULT, errno);
 
 	ASSERT_EQ(-1, landlock_create_ruleset(ruleset_attr, page_size + 1, 0));
 	ASSERT_EQ(E2BIG, errno);
 
-	ASSERT_EQ(-1, landlock_create_ruleset(ruleset_attr,
-				sizeof(struct landlock_ruleset_attr), 0));
+	/* Checks minimal valid attribute size. */
+	ASSERT_EQ(-1, landlock_create_ruleset(ruleset_attr, 8, 0));
+	ASSERT_EQ(ENOMSG, errno);
+	ASSERT_EQ(-1, landlock_create_ruleset(
+			      ruleset_attr,
+			      sizeof(struct landlock_ruleset_attr), 0));
 	ASSERT_EQ(ENOMSG, errno);
 	ASSERT_EQ(-1, landlock_create_ruleset(ruleset_attr, page_size, 0));
 	ASSERT_EQ(ENOMSG, errno);
@@ -63,38 +71,44 @@
 	free(buf);
 }
 
-TEST(abi_version) {
+TEST(abi_version)
+{
 	const struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = LANDLOCK_ACCESS_FS_READ_FILE,
 	};
 	ASSERT_EQ(1, landlock_create_ruleset(NULL, 0,
-				LANDLOCK_CREATE_RULESET_VERSION));
+					     LANDLOCK_CREATE_RULESET_VERSION));
 
 	ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr, 0,
-				LANDLOCK_CREATE_RULESET_VERSION));
+					      LANDLOCK_CREATE_RULESET_VERSION));
 	ASSERT_EQ(EINVAL, errno);
 
 	ASSERT_EQ(-1, landlock_create_ruleset(NULL, sizeof(ruleset_attr),
-				LANDLOCK_CREATE_RULESET_VERSION));
+					      LANDLOCK_CREATE_RULESET_VERSION));
 	ASSERT_EQ(EINVAL, errno);
 
-	ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr,
-				sizeof(ruleset_attr),
-				LANDLOCK_CREATE_RULESET_VERSION));
+	ASSERT_EQ(-1,
+		  landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr),
+					  LANDLOCK_CREATE_RULESET_VERSION));
 	ASSERT_EQ(EINVAL, errno);
 
 	ASSERT_EQ(-1, landlock_create_ruleset(NULL, 0,
-				LANDLOCK_CREATE_RULESET_VERSION | 1 << 31));
+					      LANDLOCK_CREATE_RULESET_VERSION |
+						      1 << 31));
 	ASSERT_EQ(EINVAL, errno);
 }
 
-TEST(inval_create_ruleset_flags) {
+/* Tests ordering of syscall argument checks. */
+TEST(create_ruleset_checks_ordering)
+{
 	const int last_flag = LANDLOCK_CREATE_RULESET_VERSION;
 	const int invalid_flag = last_flag << 1;
+	int ruleset_fd;
 	const struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = LANDLOCK_ACCESS_FS_READ_FILE,
 	};
 
+	/* Checks priority for invalid flags. */
 	ASSERT_EQ(-1, landlock_create_ruleset(NULL, 0, invalid_flag));
 	ASSERT_EQ(EINVAL, errno);
 
@@ -102,44 +116,121 @@
 	ASSERT_EQ(EINVAL, errno);
 
 	ASSERT_EQ(-1, landlock_create_ruleset(NULL, sizeof(ruleset_attr),
-				invalid_flag));
+					      invalid_flag));
+	ASSERT_EQ(EINVAL, errno);
+
+	ASSERT_EQ(-1,
+		  landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr),
+					  invalid_flag));
 	ASSERT_EQ(EINVAL, errno);
 
-	ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr,
-				sizeof(ruleset_attr), invalid_flag));
+	/* Checks too big ruleset_attr size. */
+	ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr, -1, 0));
+	ASSERT_EQ(E2BIG, errno);
+
+	/* Checks too small ruleset_attr size. */
+	ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr, 0, 0));
 	ASSERT_EQ(EINVAL, errno);
+	ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr, 1, 0));
+	ASSERT_EQ(EINVAL, errno);
+
+	/* Checks valid call. */
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
+	ASSERT_LE(0, ruleset_fd);
+	ASSERT_EQ(0, close(ruleset_fd));
 }
 
-TEST(empty_path_beneath_attr) {
+/* Tests ordering of syscall argument checks. */
+TEST(add_rule_checks_ordering)
+{
 	const struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = LANDLOCK_ACCESS_FS_EXECUTE,
 	};
-	const int ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	struct landlock_path_beneath_attr path_beneath_attr = {
+		.allowed_access = LANDLOCK_ACCESS_FS_EXECUTE,
+		.parent_fd = -1,
+	};
+	const int ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 
 	ASSERT_LE(0, ruleset_fd);
 
-	/* Similar to struct landlock_path_beneath_attr.parent_fd = 0 */
+	/* Checks invalid flags. */
+	ASSERT_EQ(-1, landlock_add_rule(-1, 0, NULL, 1));
+	ASSERT_EQ(EINVAL, errno);
+
+	/* Checks invalid ruleset FD. */
+	ASSERT_EQ(-1, landlock_add_rule(-1, 0, NULL, 0));
+	ASSERT_EQ(EBADF, errno);
+
+	/* Checks invalid rule type. */
+	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, 0, NULL, 0));
+	ASSERT_EQ(EINVAL, errno);
+
+	/* Checks invalid rule attr. */
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				NULL, 0));
+					NULL, 0));
 	ASSERT_EQ(EFAULT, errno);
+
+	/* Checks invalid path_beneath.parent_fd. */
+	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
+					&path_beneath_attr, 0));
+	ASSERT_EQ(EBADF, errno);
+
+	/* Checks valid call. */
+	path_beneath_attr.parent_fd =
+		open("/tmp", O_PATH | O_NOFOLLOW | O_DIRECTORY | O_CLOEXEC);
+	ASSERT_LE(0, path_beneath_attr.parent_fd);
+	ASSERT_EQ(0, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
+				       &path_beneath_attr, 0));
+	ASSERT_EQ(0, close(path_beneath_attr.parent_fd));
 	ASSERT_EQ(0, close(ruleset_fd));
 }
 
-TEST(inval_fd_enforce) {
+/* Tests ordering of syscall argument and permission checks. */
+TEST(restrict_self_checks_ordering)
+{
+	const struct landlock_ruleset_attr ruleset_attr = {
+		.handled_access_fs = LANDLOCK_ACCESS_FS_EXECUTE,
+	};
+	struct landlock_path_beneath_attr path_beneath_attr = {
+		.allowed_access = LANDLOCK_ACCESS_FS_EXECUTE,
+		.parent_fd = -1,
+	};
+	const int ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
+
+	ASSERT_LE(0, ruleset_fd);
+	path_beneath_attr.parent_fd =
+		open("/tmp", O_PATH | O_NOFOLLOW | O_DIRECTORY | O_CLOEXEC);
+	ASSERT_LE(0, path_beneath_attr.parent_fd);
+	ASSERT_EQ(0, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
+				       &path_beneath_attr, 0));
+	ASSERT_EQ(0, close(path_beneath_attr.parent_fd));
+
+	/* Checks unprivileged enforcement without no_new_privs. */
+	drop_caps(_metadata);
+	ASSERT_EQ(-1, landlock_restrict_self(-1, -1));
+	ASSERT_EQ(EPERM, errno);
+	ASSERT_EQ(-1, landlock_restrict_self(-1, 0));
+	ASSERT_EQ(EPERM, errno);
+	ASSERT_EQ(-1, landlock_restrict_self(ruleset_fd, 0));
+	ASSERT_EQ(EPERM, errno);
+
 	ASSERT_EQ(0, prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0));
 
+	/* Checks invalid flags. */
+	ASSERT_EQ(-1, landlock_restrict_self(-1, -1));
+	ASSERT_EQ(EINVAL, errno);
+
+	/* Checks invalid ruleset FD. */
 	ASSERT_EQ(-1, landlock_restrict_self(-1, 0));
 	ASSERT_EQ(EBADF, errno);
-}
 
-TEST(unpriv_enforce_without_no_new_privs) {
-	int err;
-
-	drop_caps(_metadata);
-	err = landlock_restrict_self(-1, 0);
-	ASSERT_EQ(EPERM, errno);
-	ASSERT_EQ(err, -1);
+	/* Checks valid call. */
+	ASSERT_EQ(0, landlock_restrict_self(ruleset_fd, 0));
+	ASSERT_EQ(0, close(ruleset_fd));
 }
 
 TEST(ruleset_fd_io)
@@ -151,8 +242,8 @@
 	char buf;
 
 	drop_caps(_metadata);
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	ASSERT_LE(0, ruleset_fd);
 
 	ASSERT_EQ(-1, write(ruleset_fd, ".", 1));
@@ -197,14 +288,15 @@
 	drop_caps(_metadata);
 
 	/* Creates a test ruleset with a simple rule. */
-	ruleset_fd_tx = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	ruleset_fd_tx =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	ASSERT_LE(0, ruleset_fd_tx);
-	path_beneath_attr.parent_fd = open("/tmp", O_PATH | O_NOFOLLOW |
-			O_DIRECTORY | O_CLOEXEC);
+	path_beneath_attr.parent_fd =
+		open("/tmp", O_PATH | O_NOFOLLOW | O_DIRECTORY | O_CLOEXEC);
 	ASSERT_LE(0, path_beneath_attr.parent_fd);
-	ASSERT_EQ(0, landlock_add_rule(ruleset_fd_tx, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath_attr, 0));
+	ASSERT_EQ(0,
+		  landlock_add_rule(ruleset_fd_tx, LANDLOCK_RULE_PATH_BENEATH,
+				    &path_beneath_attr, 0));
 	ASSERT_EQ(0, close(path_beneath_attr.parent_fd));
 
 	cmsg = CMSG_FIRSTHDR(&msg);
@@ -215,7 +307,8 @@
 	memcpy(CMSG_DATA(cmsg), &ruleset_fd_tx, sizeof(ruleset_fd_tx));
 
 	/* Sends the ruleset FD over a socketpair and then close it. */
-	ASSERT_EQ(0, socketpair(AF_UNIX, SOCK_STREAM | SOCK_CLOEXEC, 0, socket_fds));
+	ASSERT_EQ(0, socketpair(AF_UNIX, SOCK_STREAM | SOCK_CLOEXEC, 0,
+				socket_fds));
 	ASSERT_EQ(sizeof(data_tx), sendmsg(socket_fds[0], &msg, 0));
 	ASSERT_EQ(0, close(socket_fds[0]));
 	ASSERT_EQ(0, close(ruleset_fd_tx));
@@ -226,7 +319,8 @@
 		int ruleset_fd_rx;
 
 		*(char *)msg.msg_iov->iov_base = '\0';
-		ASSERT_EQ(sizeof(data_tx), recvmsg(socket_fds[1], &msg, MSG_CMSG_CLOEXEC));
+		ASSERT_EQ(sizeof(data_tx),
+			  recvmsg(socket_fds[1], &msg, MSG_CMSG_CLOEXEC));
 		ASSERT_EQ('.', *(char *)msg.msg_iov->iov_base);
 		ASSERT_EQ(0, close(socket_fds[1]));
 		cmsg = CMSG_FIRSTHDR(&msg);
@@ -263,4 +357,77 @@
 	ASSERT_EQ(EXIT_SUCCESS, WEXITSTATUS(status));
 }
 
+TEST(cred_transfer)
+{
+	struct landlock_ruleset_attr ruleset_attr = {
+		.handled_access_fs = LANDLOCK_ACCESS_FS_READ_DIR,
+	};
+	int ruleset_fd, dir_fd;
+	pid_t child;
+	int status;
+
+	drop_caps(_metadata);
+
+	dir_fd = open("/", O_RDONLY | O_DIRECTORY | O_CLOEXEC);
+	EXPECT_LE(0, dir_fd);
+	EXPECT_EQ(0, close(dir_fd));
+
+	/* Denies opening directories. */
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
+	ASSERT_LE(0, ruleset_fd);
+	EXPECT_EQ(0, prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0));
+	ASSERT_EQ(0, landlock_restrict_self(ruleset_fd, 0));
+	EXPECT_EQ(0, close(ruleset_fd));
+
+	/* Checks ruleset enforcement. */
+	EXPECT_EQ(-1, open("/", O_RDONLY | O_DIRECTORY | O_CLOEXEC));
+	EXPECT_EQ(EACCES, errno);
+
+	/* Needed for KEYCTL_SESSION_TO_PARENT permission checks */
+	EXPECT_NE(-1, syscall(__NR_keyctl, KEYCTL_JOIN_SESSION_KEYRING, NULL, 0,
+			      0, 0))
+	{
+		TH_LOG("Failed to join session keyring: %s", strerror(errno));
+	}
+
+	child = fork();
+	ASSERT_LE(0, child);
+	if (child == 0) {
+		/* Checks ruleset enforcement. */
+		EXPECT_EQ(-1, open("/", O_RDONLY | O_DIRECTORY | O_CLOEXEC));
+		EXPECT_EQ(EACCES, errno);
+
+		/*
+		 * KEYCTL_SESSION_TO_PARENT is a no-op unless we have a
+		 * different session keyring in the child, so make that happen.
+		 */
+		EXPECT_NE(-1, syscall(__NR_keyctl, KEYCTL_JOIN_SESSION_KEYRING,
+				      NULL, 0, 0, 0));
+
+		/*
+		 * KEYCTL_SESSION_TO_PARENT installs credentials on the parent
+		 * that never go through the cred_prepare hook, this path uses
+		 * cred_transfer instead.
+		 */
+		EXPECT_EQ(0, syscall(__NR_keyctl, KEYCTL_SESSION_TO_PARENT, 0,
+				     0, 0, 0));
+
+		/* Re-checks ruleset enforcement. */
+		EXPECT_EQ(-1, open("/", O_RDONLY | O_DIRECTORY | O_CLOEXEC));
+		EXPECT_EQ(EACCES, errno);
+
+		_exit(_metadata->passed ? EXIT_SUCCESS : EXIT_FAILURE);
+		return;
+	}
+
+	EXPECT_EQ(child, waitpid(child, &status, 0));
+	EXPECT_EQ(1, WIFEXITED(status));
+	EXPECT_EQ(EXIT_SUCCESS, WEXITSTATUS(status));
+
+	/* Re-checks ruleset enforcement. */
+	EXPECT_EQ(-1, open("/", O_RDONLY | O_DIRECTORY | O_CLOEXEC));
+	EXPECT_EQ(EACCES, errno);
+}
+
 TEST_HARNESS_MAIN
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/landlock/common.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/landlock/common.h
@@ -29,6 +29,7 @@
  * this to be possible, we must not call abort() but instead exit smoothly
  * (hence the step print).
  */
+/* clang-format off */
 #define TEST_F_FORK(fixture_name, test_name) \
 	static void fixture_name##_##test_name##_child( \
 		struct __test_metadata *_metadata, \
@@ -75,11 +76,12 @@
 		FIXTURE_DATA(fixture_name) __attribute__((unused)) *self, \
 		const FIXTURE_VARIANT(fixture_name) \
 			__attribute__((unused)) *variant)
+/* clang-format on */
 
 #ifndef landlock_create_ruleset
-static inline int landlock_create_ruleset(
-		const struct landlock_ruleset_attr *const attr,
-		const size_t size, const __u32 flags)
+static inline int
+landlock_create_ruleset(const struct landlock_ruleset_attr *const attr,
+			const size_t size, const __u32 flags)
 {
 	return syscall(__NR_landlock_create_ruleset, attr, size, flags);
 }
@@ -87,17 +89,18 @@
 
 #ifndef landlock_add_rule
 static inline int landlock_add_rule(const int ruleset_fd,
-		const enum landlock_rule_type rule_type,
-		const void *const rule_attr, const __u32 flags)
+				    const enum landlock_rule_type rule_type,
+				    const void *const rule_attr,
+				    const __u32 flags)
 {
-	return syscall(__NR_landlock_add_rule, ruleset_fd, rule_type,
-			rule_attr, flags);
+	return syscall(__NR_landlock_add_rule, ruleset_fd, rule_type, rule_attr,
+		       flags);
 }
 #endif
 
 #ifndef landlock_restrict_self
 static inline int landlock_restrict_self(const int ruleset_fd,
-		const __u32 flags)
+					 const __u32 flags)
 {
 	return syscall(__NR_landlock_restrict_self, ruleset_fd, flags);
 }
@@ -115,69 +118,76 @@
 	};
 
 	cap_p = cap_get_proc();
-	EXPECT_NE(NULL, cap_p) {
+	EXPECT_NE(NULL, cap_p)
+	{
 		TH_LOG("Failed to cap_get_proc: %s", strerror(errno));
 	}
-	EXPECT_NE(-1, cap_clear(cap_p)) {
+	EXPECT_NE(-1, cap_clear(cap_p))
+	{
 		TH_LOG("Failed to cap_clear: %s", strerror(errno));
 	}
 	if (!drop_all) {
 		EXPECT_NE(-1, cap_set_flag(cap_p, CAP_PERMITTED,
-					ARRAY_SIZE(caps), caps, CAP_SET)) {
+					   ARRAY_SIZE(caps), caps, CAP_SET))
+		{
 			TH_LOG("Failed to cap_set_flag: %s", strerror(errno));
 		}
 	}
-	EXPECT_NE(-1, cap_set_proc(cap_p)) {
+	EXPECT_NE(-1, cap_set_proc(cap_p))
+	{
 		TH_LOG("Failed to cap_set_proc: %s", strerror(errno));
 	}
-	EXPECT_NE(-1, cap_free(cap_p)) {
+	EXPECT_NE(-1, cap_free(cap_p))
+	{
 		TH_LOG("Failed to cap_free: %s", strerror(errno));
 	}
 }
 
 /* We cannot put such helpers in a library because of kselftest_harness.h . */
-__attribute__((__unused__))
-static void disable_caps(struct __test_metadata *const _metadata)
+__attribute__((__unused__)) static void
+disable_caps(struct __test_metadata *const _metadata)
 {
 	_init_caps(_metadata, false);
 }
 
-__attribute__((__unused__))
-static void drop_caps(struct __test_metadata *const _metadata)
+__attribute__((__unused__)) static void
+drop_caps(struct __test_metadata *const _metadata)
 {
 	_init_caps(_metadata, true);
 }
 
 static void _effective_cap(struct __test_metadata *const _metadata,
-		const cap_value_t caps, const cap_flag_value_t value)
+			   const cap_value_t caps, const cap_flag_value_t value)
 {
 	cap_t cap_p;
 
 	cap_p = cap_get_proc();
-	EXPECT_NE(NULL, cap_p) {
+	EXPECT_NE(NULL, cap_p)
+	{
 		TH_LOG("Failed to cap_get_proc: %s", strerror(errno));
 	}
-	EXPECT_NE(-1, cap_set_flag(cap_p, CAP_EFFECTIVE, 1, &caps, value)) {
+	EXPECT_NE(-1, cap_set_flag(cap_p, CAP_EFFECTIVE, 1, &caps, value))
+	{
 		TH_LOG("Failed to cap_set_flag: %s", strerror(errno));
 	}
-	EXPECT_NE(-1, cap_set_proc(cap_p)) {
+	EXPECT_NE(-1, cap_set_proc(cap_p))
+	{
 		TH_LOG("Failed to cap_set_proc: %s", strerror(errno));
 	}
-	EXPECT_NE(-1, cap_free(cap_p)) {
+	EXPECT_NE(-1, cap_free(cap_p))
+	{
 		TH_LOG("Failed to cap_free: %s", strerror(errno));
 	}
 }
 
-__attribute__((__unused__))
-static void set_cap(struct __test_metadata *const _metadata,
-		const cap_value_t caps)
+__attribute__((__unused__)) static void
+set_cap(struct __test_metadata *const _metadata, const cap_value_t caps)
 {
 	_effective_cap(_metadata, caps, CAP_SET);
 }
 
-__attribute__((__unused__))
-static void clear_cap(struct __test_metadata *const _metadata,
-		const cap_value_t caps)
+__attribute__((__unused__)) static void
+clear_cap(struct __test_metadata *const _metadata, const cap_value_t caps)
 {
 	_effective_cap(_metadata, caps, CAP_CLEAR);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/landlock/config
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/landlock/config
@@ -1,7 +1,8 @@
+CONFIG_KEYS=y
 CONFIG_OVERLAY_FS=y
+CONFIG_SECURITY=y
 CONFIG_SECURITY_LANDLOCK=y
 CONFIG_SECURITY_PATH=y
-CONFIG_SECURITY=y
 CONFIG_SHMEM=y
-CONFIG_TMPFS_XATTR=y
 CONFIG_TMPFS=y
+CONFIG_TMPFS_XATTR=y
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/landlock/fs_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/landlock/fs_test.c
@@ -11,6 +11,7 @@
 #include <fcntl.h>
 #include <linux/landlock.h>
 #include <sched.h>
+#include <stdio.h>
 #include <string.h>
 #include <sys/capability.h>
 #include <sys/mount.h>
@@ -22,8 +23,21 @@
 
 #include "common.h"
 
-#define TMP_DIR		"tmp"
-#define BINARY_PATH	"./true"
+#ifndef renameat2
+int renameat2(int olddirfd, const char *oldpath, int newdirfd,
+	      const char *newpath, unsigned int flags)
+{
+	return syscall(__NR_renameat2, olddirfd, oldpath, newdirfd, newpath,
+		       flags);
+}
+#endif
+
+#ifndef RENAME_EXCHANGE
+#define RENAME_EXCHANGE (1 << 1)
+#endif
+
+#define TMP_DIR "tmp"
+#define BINARY_PATH "./true"
 
 /* Paths (sibling number and depth) */
 static const char dir_s1d1[] = TMP_DIR "/s1d1";
@@ -74,8 +88,42 @@
  *         └── s3d3
  */
 
+static bool fgrep(FILE *const inf, const char *const str)
+{
+	char line[32];
+	const int slen = strlen(str);
+
+	while (!feof(inf)) {
+		if (!fgets(line, sizeof(line), inf))
+			break;
+		if (strncmp(line, str, slen))
+			continue;
+
+		return true;
+	}
+
+	return false;
+}
+
+static bool supports_overlayfs(void)
+{
+	bool res;
+	FILE *const inf = fopen("/proc/filesystems", "r");
+
+	/*
+	 * Consider that the filesystem is supported if we cannot get the
+	 * supported ones.
+	 */
+	if (!inf)
+		return true;
+
+	res = fgrep(inf, "nodev\toverlay\n");
+	fclose(inf);
+	return res;
+}
+
 static void mkdir_parents(struct __test_metadata *const _metadata,
-		const char *const path)
+			  const char *const path)
 {
 	char *walker;
 	const char *parent;
@@ -90,9 +138,10 @@
 			continue;
 		walker[i] = '\0';
 		err = mkdir(parent, 0700);
-		ASSERT_FALSE(err && errno != EEXIST) {
-			TH_LOG("Failed to create directory \"%s\": %s",
-					parent, strerror(errno));
+		ASSERT_FALSE(err && errno != EEXIST)
+		{
+			TH_LOG("Failed to create directory \"%s\": %s", parent,
+			       strerror(errno));
 		}
 		walker[i] = '/';
 	}
@@ -100,22 +149,24 @@
 }
 
 static void create_directory(struct __test_metadata *const _metadata,
-		const char *const path)
+			     const char *const path)
 {
 	mkdir_parents(_metadata, path);
-	ASSERT_EQ(0, mkdir(path, 0700)) {
+	ASSERT_EQ(0, mkdir(path, 0700))
+	{
 		TH_LOG("Failed to create directory \"%s\": %s", path,
-				strerror(errno));
+		       strerror(errno));
 	}
 }
 
 static void create_file(struct __test_metadata *const _metadata,
-		const char *const path)
+			const char *const path)
 {
 	mkdir_parents(_metadata, path);
-	ASSERT_EQ(0, mknod(path, S_IFREG | 0700, 0)) {
+	ASSERT_EQ(0, mknod(path, S_IFREG | 0700, 0))
+	{
 		TH_LOG("Failed to create file \"%s\": %s", path,
-				strerror(errno));
+		       strerror(errno));
 	}
 }
 
@@ -221,8 +272,9 @@
 	EXPECT_EQ(0, remove_path(dir_s3d2));
 }
 
-FIXTURE(layout1) {
-};
+/* clang-format off */
+FIXTURE(layout1) {};
+/* clang-format on */
 
 FIXTURE_SETUP(layout1)
 {
@@ -242,7 +294,8 @@
  * This helper enables to use the ASSERT_* macros and print the line number
  * pointing to the test caller.
  */
-static int test_open_rel(const int dirfd, const char *const path, const int flags)
+static int test_open_rel(const int dirfd, const char *const path,
+			 const int flags)
 {
 	int fd;
 
@@ -291,23 +344,23 @@
 {
 	struct landlock_path_beneath_attr path_beneath = {
 		.allowed_access = LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		.parent_fd = -1,
 	};
 	struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_WRITE_FILE,
+				     LANDLOCK_ACCESS_FS_WRITE_FILE,
 	};
 	int ruleset_fd;
 
-	path_beneath.parent_fd = open(dir_s1d2, O_PATH | O_DIRECTORY |
-			O_CLOEXEC);
+	path_beneath.parent_fd =
+		open(dir_s1d2, O_PATH | O_DIRECTORY | O_CLOEXEC);
 	ASSERT_LE(0, path_beneath.parent_fd);
 
 	ruleset_fd = open(dir_s1d1, O_PATH | O_DIRECTORY | O_CLOEXEC);
 	ASSERT_LE(0, ruleset_fd);
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	/* Returns EBADF because ruleset_fd is not a landlock-ruleset FD. */
 	ASSERT_EQ(EBADF, errno);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -315,55 +368,55 @@
 	ruleset_fd = open(dir_s1d1, O_DIRECTORY | O_CLOEXEC);
 	ASSERT_LE(0, ruleset_fd);
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	/* Returns EBADFD because ruleset_fd is not a valid ruleset. */
 	ASSERT_EQ(EBADFD, errno);
 	ASSERT_EQ(0, close(ruleset_fd));
 
 	/* Gets a real ruleset. */
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	ASSERT_LE(0, ruleset_fd);
 	ASSERT_EQ(0, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+				       &path_beneath, 0));
 	ASSERT_EQ(0, close(path_beneath.parent_fd));
 
 	/* Tests without O_PATH. */
 	path_beneath.parent_fd = open(dir_s1d2, O_DIRECTORY | O_CLOEXEC);
 	ASSERT_LE(0, path_beneath.parent_fd);
 	ASSERT_EQ(0, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+				       &path_beneath, 0));
 	ASSERT_EQ(0, close(path_beneath.parent_fd));
 
 	/* Tests with a ruleset FD. */
 	path_beneath.parent_fd = ruleset_fd;
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	ASSERT_EQ(EBADFD, errno);
 
 	/* Checks unhandled allowed_access. */
-	path_beneath.parent_fd = open(dir_s1d2, O_PATH | O_DIRECTORY |
-			O_CLOEXEC);
+	path_beneath.parent_fd =
+		open(dir_s1d2, O_PATH | O_DIRECTORY | O_CLOEXEC);
 	ASSERT_LE(0, path_beneath.parent_fd);
 
 	/* Test with legitimate values. */
 	path_beneath.allowed_access |= LANDLOCK_ACCESS_FS_EXECUTE;
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	ASSERT_EQ(EINVAL, errno);
 	path_beneath.allowed_access &= ~LANDLOCK_ACCESS_FS_EXECUTE;
 
 	/* Test with unknown (64-bits) value. */
 	path_beneath.allowed_access |= (1ULL << 60);
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	ASSERT_EQ(EINVAL, errno);
 	path_beneath.allowed_access &= ~(1ULL << 60);
 
 	/* Test with no access. */
 	path_beneath.allowed_access = 0;
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	ASSERT_EQ(ENOMSG, errno);
 	path_beneath.allowed_access &= ~(1ULL << 60);
 
@@ -376,6 +429,8 @@
 	ASSERT_EQ(0, close(ruleset_fd));
 }
 
+/* clang-format off */
+
 #define ACCESS_FILE ( \
 	LANDLOCK_ACCESS_FS_EXECUTE | \
 	LANDLOCK_ACCESS_FS_WRITE_FILE | \
@@ -396,53 +451,87 @@
 	LANDLOCK_ACCESS_FS_MAKE_BLOCK | \
 	ACCESS_LAST)
 
-TEST_F_FORK(layout1, file_access_rights)
+/* clang-format on */
+
+TEST_F_FORK(layout1, file_and_dir_access_rights)
 {
 	__u64 access;
 	int err;
-	struct landlock_path_beneath_attr path_beneath = {};
+	struct landlock_path_beneath_attr path_beneath_file = {},
+					  path_beneath_dir = {};
 	struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = ACCESS_ALL,
 	};
-	const int ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	const int ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 
 	ASSERT_LE(0, ruleset_fd);
 
 	/* Tests access rights for files. */
-	path_beneath.parent_fd = open(file1_s1d2, O_PATH | O_CLOEXEC);
-	ASSERT_LE(0, path_beneath.parent_fd);
+	path_beneath_file.parent_fd = open(file1_s1d2, O_PATH | O_CLOEXEC);
+	ASSERT_LE(0, path_beneath_file.parent_fd);
+
+	/* Tests access rights for directories. */
+	path_beneath_dir.parent_fd =
+		open(dir_s1d2, O_PATH | O_DIRECTORY | O_CLOEXEC);
+	ASSERT_LE(0, path_beneath_dir.parent_fd);
+
 	for (access = 1; access <= ACCESS_LAST; access <<= 1) {
-		path_beneath.allowed_access = access;
+		path_beneath_dir.allowed_access = access;
+		ASSERT_EQ(0, landlock_add_rule(ruleset_fd,
+					       LANDLOCK_RULE_PATH_BENEATH,
+					       &path_beneath_dir, 0));
+
+		path_beneath_file.allowed_access = access;
 		err = landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0);
-		if ((access | ACCESS_FILE) == ACCESS_FILE) {
+					&path_beneath_file, 0);
+		if (access & ACCESS_FILE) {
 			ASSERT_EQ(0, err);
 		} else {
 			ASSERT_EQ(-1, err);
 			ASSERT_EQ(EINVAL, errno);
 		}
 	}
-	ASSERT_EQ(0, close(path_beneath.parent_fd));
+	ASSERT_EQ(0, close(path_beneath_file.parent_fd));
+	ASSERT_EQ(0, close(path_beneath_dir.parent_fd));
+	ASSERT_EQ(0, close(ruleset_fd));
+}
+
+TEST_F_FORK(layout1, unknown_access_rights)
+{
+	__u64 access_mask;
+
+	for (access_mask = 1ULL << 63; access_mask != ACCESS_LAST;
+	     access_mask >>= 1) {
+		struct landlock_ruleset_attr ruleset_attr = {
+			.handled_access_fs = access_mask,
+		};
+
+		ASSERT_EQ(-1, landlock_create_ruleset(&ruleset_attr,
+						      sizeof(ruleset_attr), 0));
+		ASSERT_EQ(EINVAL, errno);
+	}
 }
 
 static void add_path_beneath(struct __test_metadata *const _metadata,
-		const int ruleset_fd, const __u64 allowed_access,
-		const char *const path)
+			     const int ruleset_fd, const __u64 allowed_access,
+			     const char *const path)
 {
 	struct landlock_path_beneath_attr path_beneath = {
 		.allowed_access = allowed_access,
 	};
 
 	path_beneath.parent_fd = open(path, O_PATH | O_CLOEXEC);
-	ASSERT_LE(0, path_beneath.parent_fd) {
+	ASSERT_LE(0, path_beneath.parent_fd)
+	{
 		TH_LOG("Failed to open directory \"%s\": %s", path,
-				strerror(errno));
+		       strerror(errno));
 	}
 	ASSERT_EQ(0, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0)) {
+				       &path_beneath, 0))
+	{
 		TH_LOG("Failed to update the ruleset with \"%s\": %s", path,
-				strerror(errno));
+		       strerror(errno));
 	}
 	ASSERT_EQ(0, close(path_beneath.parent_fd));
 }
@@ -452,6 +541,8 @@
 	__u64 access;
 };
 
+/* clang-format off */
+
 #define ACCESS_RO ( \
 	LANDLOCK_ACCESS_FS_READ_FILE | \
 	LANDLOCK_ACCESS_FS_READ_DIR)
@@ -460,39 +551,46 @@
 	ACCESS_RO | \
 	LANDLOCK_ACCESS_FS_WRITE_FILE)
 
+/* clang-format on */
+
 static int create_ruleset(struct __test_metadata *const _metadata,
-		const __u64 handled_access_fs, const struct rule rules[])
+			  const __u64 handled_access_fs,
+			  const struct rule rules[])
 {
 	int ruleset_fd, i;
 	struct landlock_ruleset_attr ruleset_attr = {
 		.handled_access_fs = handled_access_fs,
 	};
 
-	ASSERT_NE(NULL, rules) {
+	ASSERT_NE(NULL, rules)
+	{
 		TH_LOG("No rule list");
 	}
-	ASSERT_NE(NULL, rules[0].path) {
+	ASSERT_NE(NULL, rules[0].path)
+	{
 		TH_LOG("Empty rule list");
 	}
 
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
-	ASSERT_LE(0, ruleset_fd) {
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
+	ASSERT_LE(0, ruleset_fd)
+	{
 		TH_LOG("Failed to create a ruleset: %s", strerror(errno));
 	}
 
 	for (i = 0; rules[i].path; i++) {
 		add_path_beneath(_metadata, ruleset_fd, rules[i].access,
-				rules[i].path);
+				 rules[i].path);
 	}
 	return ruleset_fd;
 }
 
 static void enforce_ruleset(struct __test_metadata *const _metadata,
-		const int ruleset_fd)
+			    const int ruleset_fd)
 {
 	ASSERT_EQ(0, prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0));
-	ASSERT_EQ(0, landlock_restrict_self(ruleset_fd, 0)) {
+	ASSERT_EQ(0, landlock_restrict_self(ruleset_fd, 0))
+	{
 		TH_LOG("Failed to enforce ruleset: %s", strerror(errno));
 	}
 }
@@ -503,13 +601,14 @@
 		{
 			.path = "/dev/null",
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	struct landlock_path_beneath_attr path_beneath;
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access |
-			LANDLOCK_ACCESS_FS_READ_DIR, rules);
+	const int ruleset_fd = create_ruleset(
+		_metadata, rules[0].access | LANDLOCK_ACCESS_FS_READ_DIR,
+		rules);
 
 	ASSERT_LE(0, ruleset_fd);
 	ASSERT_EQ(0, test_open("/proc/self/ns/mnt", O_RDONLY));
@@ -536,22 +635,23 @@
 	 * references to a ruleset.
 	 */
 	path_beneath.allowed_access = LANDLOCK_ACCESS_FS_READ_FILE |
-		LANDLOCK_ACCESS_FS_WRITE_FILE,
+				      LANDLOCK_ACCESS_FS_WRITE_FILE,
 	path_beneath.parent_fd = open("/proc/self/ns/mnt", O_PATH | O_CLOEXEC);
 	ASSERT_LE(0, path_beneath.parent_fd);
 	ASSERT_EQ(-1, landlock_add_rule(ruleset_fd, LANDLOCK_RULE_PATH_BENEATH,
-				&path_beneath, 0));
+					&path_beneath, 0));
 	ASSERT_EQ(EBADFD, errno);
 	ASSERT_EQ(0, close(path_beneath.parent_fd));
 }
 
-TEST_F_FORK(layout1, unpriv) {
+TEST_F_FORK(layout1, unpriv)
+{
 	const struct rule rules[] = {
 		{
 			.path = dir_s1d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd;
 
@@ -577,9 +677,9 @@
 		{
 			.path = file1_s2d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 	char buf;
@@ -589,17 +689,23 @@
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
 
-	/* Tests on a directory. */
+	/* Tests on a directory (with or without O_PATH). */
 	ASSERT_EQ(EACCES, test_open("/", O_RDONLY));
+	ASSERT_EQ(0, test_open("/", O_RDONLY | O_PATH));
 	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY));
+	ASSERT_EQ(0, test_open(dir_s1d1, O_RDONLY | O_PATH));
 	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDONLY));
+	ASSERT_EQ(0, test_open(file1_s1d1, O_RDONLY | O_PATH));
+
 	ASSERT_EQ(0, test_open(dir_s1d2, O_RDONLY));
 	ASSERT_EQ(0, test_open(file1_s1d2, O_RDONLY));
 	ASSERT_EQ(0, test_open(dir_s1d3, O_RDONLY));
 	ASSERT_EQ(0, test_open(file1_s1d3, O_RDONLY));
 
-	/* Tests on a file. */
+	/* Tests on a file (with or without O_PATH). */
 	ASSERT_EQ(EACCES, test_open(dir_s2d2, O_RDONLY));
+	ASSERT_EQ(0, test_open(dir_s2d2, O_RDONLY | O_PATH));
+
 	ASSERT_EQ(0, test_open(file1_s2d2, O_RDONLY));
 
 	/* Checks effective read and write actions. */
@@ -626,7 +732,7 @@
 			.path = dir_s1d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	/* Here, we only handle read accesses, not write accesses. */
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RO, rules);
@@ -653,14 +759,14 @@
 		{
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
 		{
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_READ_DIR,
+				  LANDLOCK_ACCESS_FS_READ_DIR,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -687,6 +793,113 @@
 	ASSERT_EQ(0, test_open(dir_s1d3, O_RDONLY | O_DIRECTORY));
 }
 
+TEST_F_FORK(layout1, layer_rule_unions)
+{
+	const struct rule layer1[] = {
+		{
+			.path = dir_s1d2,
+			.access = LANDLOCK_ACCESS_FS_READ_FILE,
+		},
+		/* dir_s1d3 should allow READ_FILE and WRITE_FILE (O_RDWR). */
+		{
+			.path = dir_s1d3,
+			.access = LANDLOCK_ACCESS_FS_WRITE_FILE,
+		},
+		{},
+	};
+	const struct rule layer2[] = {
+		/* Doesn't change anything from layer1. */
+		{
+			.path = dir_s1d2,
+			.access = LANDLOCK_ACCESS_FS_READ_FILE |
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
+		},
+		{},
+	};
+	const struct rule layer3[] = {
+		/* Only allows write (but not read) to dir_s1d3. */
+		{
+			.path = dir_s1d2,
+			.access = LANDLOCK_ACCESS_FS_WRITE_FILE,
+		},
+		{},
+	};
+	int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, layer1);
+
+	ASSERT_LE(0, ruleset_fd);
+	enforce_ruleset(_metadata, ruleset_fd);
+	ASSERT_EQ(0, close(ruleset_fd));
+
+	/* Checks s1d1 hierarchy with layer1. */
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_WRONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Checks s1d2 hierarchy with layer1. */
+	ASSERT_EQ(0, test_open(file1_s1d2, O_RDONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_WRONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Checks s1d3 hierarchy with layer1. */
+	ASSERT_EQ(0, test_open(file1_s1d3, O_RDONLY));
+	ASSERT_EQ(0, test_open(file1_s1d3, O_WRONLY));
+	/* dir_s1d3 should allow READ_FILE and WRITE_FILE (O_RDWR). */
+	ASSERT_EQ(0, test_open(file1_s1d3, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Doesn't change anything from layer1. */
+	ruleset_fd = create_ruleset(_metadata, ACCESS_RW, layer2);
+	ASSERT_LE(0, ruleset_fd);
+	enforce_ruleset(_metadata, ruleset_fd);
+	ASSERT_EQ(0, close(ruleset_fd));
+
+	/* Checks s1d1 hierarchy with layer2. */
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_WRONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Checks s1d2 hierarchy with layer2. */
+	ASSERT_EQ(0, test_open(file1_s1d2, O_RDONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_WRONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Checks s1d3 hierarchy with layer2. */
+	ASSERT_EQ(0, test_open(file1_s1d3, O_RDONLY));
+	ASSERT_EQ(0, test_open(file1_s1d3, O_WRONLY));
+	/* dir_s1d3 should allow READ_FILE and WRITE_FILE (O_RDWR). */
+	ASSERT_EQ(0, test_open(file1_s1d3, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Only allows write (but not read) to dir_s1d3. */
+	ruleset_fd = create_ruleset(_metadata, ACCESS_RW, layer3);
+	ASSERT_LE(0, ruleset_fd);
+	enforce_ruleset(_metadata, ruleset_fd);
+	ASSERT_EQ(0, close(ruleset_fd));
+
+	/* Checks s1d1 hierarchy with layer3. */
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_WRONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Checks s1d2 hierarchy with layer3. */
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_RDONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_WRONLY));
+	ASSERT_EQ(EACCES, test_open(file1_s1d2, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+
+	/* Checks s1d3 hierarchy with layer3. */
+	ASSERT_EQ(EACCES, test_open(file1_s1d3, O_RDONLY));
+	ASSERT_EQ(0, test_open(file1_s1d3, O_WRONLY));
+	/* dir_s1d3 should now deny READ_FILE and WRITE_FILE (O_RDWR). */
+	ASSERT_EQ(EACCES, test_open(file1_s1d3, O_RDWR));
+	ASSERT_EQ(EACCES, test_open(dir_s1d1, O_RDONLY | O_DIRECTORY));
+}
+
 TEST_F_FORK(layout1, non_overlapping_accesses)
 {
 	const struct rule layer1[] = {
@@ -694,22 +907,22 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_MAKE_REG,
 		},
-		{}
+		{},
 	};
 	const struct rule layer2[] = {
 		{
 			.path = dir_s1d3,
 			.access = LANDLOCK_ACCESS_FS_REMOVE_FILE,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd;
 
 	ASSERT_EQ(0, unlink(file1_s1d1));
 	ASSERT_EQ(0, unlink(file1_s1d2));
 
-	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_MAKE_REG,
-			layer1);
+	ruleset_fd =
+		create_ruleset(_metadata, LANDLOCK_ACCESS_FS_MAKE_REG, layer1);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -720,7 +933,7 @@
 	ASSERT_EQ(0, unlink(file1_s1d2));
 
 	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_REMOVE_FILE,
-			layer2);
+				    layer2);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -758,7 +971,7 @@
 			.path = file1_s1d3,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	/* First rule with write restrictions. */
 	const struct rule layer2_read_write[] = {
@@ -766,14 +979,14 @@
 		{
 			.path = dir_s1d3,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
 		/* ...but also denies read access via its grandparent directory. */
 		{
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	const struct rule layer3_read[] = {
 		/* Allows read access via its great-grandparent directory. */
@@ -781,7 +994,7 @@
 			.path = dir_s1d1,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	const struct rule layer4_read_write[] = {
 		/*
@@ -792,7 +1005,7 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	const struct rule layer5_read[] = {
 		/*
@@ -803,7 +1016,7 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	const struct rule layer6_execute[] = {
 		/*
@@ -814,7 +1027,7 @@
 			.path = dir_s2d1,
 			.access = LANDLOCK_ACCESS_FS_EXECUTE,
 		},
-		{}
+		{},
 	};
 	const struct rule layer7_read_write[] = {
 		/*
@@ -825,12 +1038,12 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd;
 
 	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_READ_FILE,
-			layer1_read);
+				    layer1_read);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -840,8 +1053,10 @@
 	ASSERT_EQ(EACCES, test_open(file2_s1d3, O_RDONLY));
 	ASSERT_EQ(0, test_open(file2_s1d3, O_WRONLY));
 
-	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_WRITE_FILE, layer2_read_write);
+	ruleset_fd = create_ruleset(_metadata,
+				    LANDLOCK_ACCESS_FS_READ_FILE |
+					    LANDLOCK_ACCESS_FS_WRITE_FILE,
+				    layer2_read_write);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -852,7 +1067,7 @@
 	ASSERT_EQ(0, test_open(file2_s1d3, O_WRONLY));
 
 	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_READ_FILE,
-			layer3_read);
+				    layer3_read);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -863,8 +1078,10 @@
 	ASSERT_EQ(0, test_open(file2_s1d3, O_WRONLY));
 
 	/* This time, denies write access for the file hierarchy. */
-	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_WRITE_FILE, layer4_read_write);
+	ruleset_fd = create_ruleset(_metadata,
+				    LANDLOCK_ACCESS_FS_READ_FILE |
+					    LANDLOCK_ACCESS_FS_WRITE_FILE,
+				    layer4_read_write);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -879,7 +1096,7 @@
 	ASSERT_EQ(EACCES, test_open(file2_s1d3, O_WRONLY));
 
 	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_READ_FILE,
-			layer5_read);
+				    layer5_read);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -891,7 +1108,7 @@
 	ASSERT_EQ(EACCES, test_open(file2_s1d3, O_RDONLY));
 
 	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_EXECUTE,
-			layer6_execute);
+				    layer6_execute);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -902,8 +1119,10 @@
 	ASSERT_EQ(EACCES, test_open(file2_s1d3, O_WRONLY));
 	ASSERT_EQ(EACCES, test_open(file2_s1d3, O_RDONLY));
 
-	ruleset_fd = create_ruleset(_metadata, LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_WRITE_FILE, layer7_read_write);
+	ruleset_fd = create_ruleset(_metadata,
+				    LANDLOCK_ACCESS_FS_READ_FILE |
+					    LANDLOCK_ACCESS_FS_WRITE_FILE,
+				    layer7_read_write);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
@@ -921,9 +1140,9 @@
 		{
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_READ_DIR,
+				  LANDLOCK_ACCESS_FS_READ_DIR,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -949,7 +1168,7 @@
 	 * ANDed with the previous ones.
 	 */
 	add_path_beneath(_metadata, ruleset_fd, LANDLOCK_ACCESS_FS_WRITE_FILE,
-			dir_s1d2);
+			 dir_s1d2);
 	/*
 	 * According to ruleset_fd, dir_s1d2 should now have the
 	 * LANDLOCK_ACCESS_FS_READ_FILE and LANDLOCK_ACCESS_FS_WRITE_FILE
@@ -1004,7 +1223,7 @@
 	 * that there was no rule tied to it before.
 	 */
 	add_path_beneath(_metadata, ruleset_fd, LANDLOCK_ACCESS_FS_WRITE_FILE,
-			dir_s1d3);
+			 dir_s1d3);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
 
@@ -1039,7 +1258,7 @@
 			.path = dir_s1d3,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1054,8 +1273,10 @@
 	ASSERT_EQ(0, test_open(file1_s1d3, O_RDONLY));
 
 	/* Now dir_s1d2, parent of dir_s1d3, gets a new rule tied to it. */
-	add_path_beneath(_metadata, ruleset_fd, LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_READ_DIR, dir_s1d2);
+	add_path_beneath(_metadata, ruleset_fd,
+			 LANDLOCK_ACCESS_FS_READ_FILE |
+				 LANDLOCK_ACCESS_FS_READ_DIR,
+			 dir_s1d2);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
 
@@ -1075,12 +1296,12 @@
 			.path = dir_s1d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
 	ASSERT_LE(0, ruleset_fd);
-	for (i = 0; i < 64; i++)
+	for (i = 0; i < 16; i++)
 		enforce_ruleset(_metadata, ruleset_fd);
 
 	for (i = 0; i < 2; i++) {
@@ -1097,15 +1318,15 @@
 	int ruleset_fd;
 
 	/* Tests empty handled_access_fs. */
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	ASSERT_LE(-1, ruleset_fd);
 	ASSERT_EQ(ENOMSG, errno);
 
 	/* Enforces policy which deny read access to all files. */
 	ruleset_attr.handled_access_fs = LANDLOCK_ACCESS_FS_READ_FILE;
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDONLY));
@@ -1113,8 +1334,8 @@
 
 	/* Nests a policy which deny read access to all directories. */
 	ruleset_attr.handled_access_fs = LANDLOCK_ACCESS_FS_READ_DIR;
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(EACCES, test_open(file1_s1d1, O_RDONLY));
@@ -1137,7 +1358,7 @@
 			.path = dir_s3d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1166,7 +1387,7 @@
 			.path = dir_s3d1,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1194,7 +1415,7 @@
 			.path = "/",
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1224,7 +1445,7 @@
 			.path = "/",
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1244,12 +1465,13 @@
 			.path = "s3d3",
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd;
 
 	set_cap(_metadata, CAP_SYS_ADMIN);
-	ASSERT_EQ(0, syscall(SYS_pivot_root, dir_s3d2, dir_s3d3)) {
+	ASSERT_EQ(0, syscall(__NR_pivot_root, dir_s3d2, dir_s3d3))
+	{
 		TH_LOG("Failed to pivot root: %s", strerror(errno));
 	};
 	ASSERT_EQ(0, chdir("/"));
@@ -1271,7 +1493,7 @@
 			.path = dir_s3d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1282,7 +1504,7 @@
 	set_cap(_metadata, CAP_SYS_ADMIN);
 	ASSERT_EQ(-1, mount(NULL, dir_s3d2, NULL, MS_RDONLY, NULL));
 	ASSERT_EQ(EPERM, errno);
-	ASSERT_EQ(-1, syscall(SYS_pivot_root, dir_s3d2, dir_s3d3));
+	ASSERT_EQ(-1, syscall(__NR_pivot_root, dir_s3d2, dir_s3d3));
 	ASSERT_EQ(EPERM, errno);
 	clear_cap(_metadata, CAP_SYS_ADMIN);
 }
@@ -1294,28 +1516,29 @@
 			.path = dir_s3d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 
 	set_cap(_metadata, CAP_SYS_ADMIN);
-	ASSERT_EQ(0, syscall(SYS_move_mount, AT_FDCWD, dir_s3d2, AT_FDCWD,
-				dir_s1d2, 0)) {
+	ASSERT_EQ(0, syscall(__NR_move_mount, AT_FDCWD, dir_s3d2, AT_FDCWD,
+			     dir_s1d2, 0))
+	{
 		TH_LOG("Failed to move mount: %s", strerror(errno));
 	}
 
-	ASSERT_EQ(0, syscall(SYS_move_mount, AT_FDCWD, dir_s1d2, AT_FDCWD,
-				dir_s3d2, 0));
+	ASSERT_EQ(0, syscall(__NR_move_mount, AT_FDCWD, dir_s1d2, AT_FDCWD,
+			     dir_s3d2, 0));
 	clear_cap(_metadata, CAP_SYS_ADMIN);
 
 	enforce_ruleset(_metadata, ruleset_fd);
 	ASSERT_EQ(0, close(ruleset_fd));
 
 	set_cap(_metadata, CAP_SYS_ADMIN);
-	ASSERT_EQ(-1, syscall(SYS_move_mount, AT_FDCWD, dir_s3d2, AT_FDCWD,
-				dir_s1d2, 0));
+	ASSERT_EQ(-1, syscall(__NR_move_mount, AT_FDCWD, dir_s3d2, AT_FDCWD,
+			      dir_s1d2, 0));
 	ASSERT_EQ(EPERM, errno);
 	clear_cap(_metadata, CAP_SYS_ADMIN);
 }
@@ -1335,7 +1558,7 @@
 			.path = dir_s3d3,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, ACCESS_RW, rules);
 
@@ -1362,7 +1585,7 @@
 };
 
 static void test_relative_path(struct __test_metadata *const _metadata,
-		const enum relative_access rel)
+			       const enum relative_access rel)
 {
 	/*
 	 * Common layer to check that chroot doesn't ignore it (i.e. a chroot
@@ -1373,7 +1596,7 @@
 			.path = TMP_DIR,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	const struct rule layer2_subs[] = {
 		{
@@ -1384,7 +1607,7 @@
 			.path = dir_s2d2,
 			.access = ACCESS_RO,
 		},
-		{}
+		{},
 	};
 	int dirfd, ruleset_fd;
 
@@ -1425,14 +1648,16 @@
 		break;
 	case REL_CHROOT_ONLY:
 		/* Do chroot into dir_s1d2 (relative to dir_s2d2). */
-		ASSERT_EQ(0, chroot("../../s1d1/s1d2")) {
+		ASSERT_EQ(0, chroot("../../s1d1/s1d2"))
+		{
 			TH_LOG("Failed to chroot: %s", strerror(errno));
 		}
 		dirfd = AT_FDCWD;
 		break;
 	case REL_CHROOT_CHDIR:
 		/* Do chroot into dir_s1d2. */
-		ASSERT_EQ(0, chroot(".")) {
+		ASSERT_EQ(0, chroot("."))
+		{
 			TH_LOG("Failed to chroot: %s", strerror(errno));
 		}
 		dirfd = AT_FDCWD;
@@ -1440,7 +1665,7 @@
 	}
 
 	ASSERT_EQ((rel == REL_CHROOT_CHDIR) ? 0 : EACCES,
-			test_open_rel(dirfd, "..", O_RDONLY));
+		  test_open_rel(dirfd, "..", O_RDONLY));
 	ASSERT_EQ(0, test_open_rel(dirfd, ".", O_RDONLY));
 
 	if (rel == REL_CHROOT_ONLY) {
@@ -1462,11 +1687,13 @@
 	if (rel != REL_CHROOT_CHDIR) {
 		ASSERT_EQ(EACCES, test_open_rel(dirfd, "../../s1d1", O_RDONLY));
 		ASSERT_EQ(0, test_open_rel(dirfd, "../../s1d1/s1d2", O_RDONLY));
-		ASSERT_EQ(0, test_open_rel(dirfd, "../../s1d1/s1d2/s1d3", O_RDONLY));
+		ASSERT_EQ(0, test_open_rel(dirfd, "../../s1d1/s1d2/s1d3",
+					   O_RDONLY));
 
 		ASSERT_EQ(EACCES, test_open_rel(dirfd, "../../s2d1", O_RDONLY));
 		ASSERT_EQ(0, test_open_rel(dirfd, "../../s2d1/s2d2", O_RDONLY));
-		ASSERT_EQ(0, test_open_rel(dirfd, "../../s2d1/s2d2/s2d3", O_RDONLY));
+		ASSERT_EQ(0, test_open_rel(dirfd, "../../s2d1/s2d2/s2d3",
+					   O_RDONLY));
 	}
 
 	if (rel == REL_OPEN)
@@ -1495,40 +1722,42 @@
 }
 
 static void copy_binary(struct __test_metadata *const _metadata,
-		const char *const dst_path)
+			const char *const dst_path)
 {
 	int dst_fd, src_fd;
 	struct stat statbuf;
 
 	dst_fd = open(dst_path, O_WRONLY | O_TRUNC | O_CLOEXEC);
-	ASSERT_LE(0, dst_fd) {
-		TH_LOG("Failed to open \"%s\": %s", dst_path,
-				strerror(errno));
+	ASSERT_LE(0, dst_fd)
+	{
+		TH_LOG("Failed to open \"%s\": %s", dst_path, strerror(errno));
 	}
 	src_fd = open(BINARY_PATH, O_RDONLY | O_CLOEXEC);
-	ASSERT_LE(0, src_fd) {
+	ASSERT_LE(0, src_fd)
+	{
 		TH_LOG("Failed to open \"" BINARY_PATH "\": %s",
-				strerror(errno));
+		       strerror(errno));
 	}
 	ASSERT_EQ(0, fstat(src_fd, &statbuf));
-	ASSERT_EQ(statbuf.st_size, sendfile(dst_fd, src_fd, 0,
-				statbuf.st_size));
+	ASSERT_EQ(statbuf.st_size,
+		  sendfile(dst_fd, src_fd, 0, statbuf.st_size));
 	ASSERT_EQ(0, close(src_fd));
 	ASSERT_EQ(0, close(dst_fd));
 }
 
-static void test_execute(struct __test_metadata *const _metadata,
-		const int err, const char *const path)
+static void test_execute(struct __test_metadata *const _metadata, const int err,
+			 const char *const path)
 {
 	int status;
-	char *const argv[] = {(char *)path, NULL};
+	char *const argv[] = { (char *)path, NULL };
 	const pid_t child = fork();
 
 	ASSERT_LE(0, child);
 	if (child == 0) {
-		ASSERT_EQ(err ? -1 : 0, execve(path, argv, NULL)) {
+		ASSERT_EQ(err ? -1 : 0, execve(path, argv, NULL))
+		{
 			TH_LOG("Failed to execute \"%s\": %s", path,
-					strerror(errno));
+			       strerror(errno));
 		};
 		ASSERT_EQ(err, errno);
 		_exit(_metadata->passed ? 2 : 1);
@@ -1536,9 +1765,9 @@
 	}
 	ASSERT_EQ(child, waitpid(child, &status, 0));
 	ASSERT_EQ(1, WIFEXITED(status));
-	ASSERT_EQ(err ? 2 : 0, WEXITSTATUS(status)) {
-		TH_LOG("Unexpected return code for \"%s\": %s", path,
-				strerror(errno));
+	ASSERT_EQ(err ? 2 : 0, WEXITSTATUS(status))
+	{
+		TH_LOG("Unexpected return code for \"%s\"", path);
 	};
 }
 
@@ -1549,10 +1778,10 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_EXECUTE,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 	copy_binary(_metadata, file1_s1d1);
@@ -1577,15 +1806,21 @@
 
 TEST_F_FORK(layout1, link)
 {
-	const struct rule rules[] = {
+	const struct rule layer1[] = {
 		{
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_MAKE_REG,
 		},
-		{}
+		{},
+	};
+	const struct rule layer2[] = {
+		{
+			.path = dir_s1d3,
+			.access = LANDLOCK_ACCESS_FS_REMOVE_FILE,
+		},
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	int ruleset_fd = create_ruleset(_metadata, layer1[0].access, layer1);
 
 	ASSERT_LE(0, ruleset_fd);
 
@@ -1598,14 +1833,30 @@
 
 	ASSERT_EQ(-1, link(file2_s1d1, file1_s1d1));
 	ASSERT_EQ(EACCES, errno);
+
 	/* Denies linking because of reparenting. */
 	ASSERT_EQ(-1, link(file1_s2d1, file1_s1d2));
 	ASSERT_EQ(EXDEV, errno);
 	ASSERT_EQ(-1, link(file2_s1d2, file1_s1d3));
 	ASSERT_EQ(EXDEV, errno);
+	ASSERT_EQ(-1, link(file2_s1d3, file1_s1d2));
+	ASSERT_EQ(EXDEV, errno);
 
 	ASSERT_EQ(0, link(file2_s1d2, file1_s1d2));
 	ASSERT_EQ(0, link(file2_s1d3, file1_s1d3));
+
+	/* Prepares for next unlinks. */
+	ASSERT_EQ(0, unlink(file2_s1d2));
+	ASSERT_EQ(0, unlink(file2_s1d3));
+
+	ruleset_fd = create_ruleset(_metadata, layer2[0].access, layer2);
+	ASSERT_LE(0, ruleset_fd);
+	enforce_ruleset(_metadata, ruleset_fd);
+	ASSERT_EQ(0, close(ruleset_fd));
+
+	/* Checks that linkind doesn't require the ability to delete a file. */
+	ASSERT_EQ(0, link(file1_s1d2, file2_s1d2));
+	ASSERT_EQ(0, link(file1_s1d3, file2_s1d3));
 }
 
 TEST_F_FORK(layout1, rename_file)
@@ -1619,14 +1870,13 @@
 			.path = dir_s2d2,
 			.access = LANDLOCK_ACCESS_FS_REMOVE_FILE,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 
-	ASSERT_EQ(0, unlink(file1_s1d1));
 	ASSERT_EQ(0, unlink(file1_s1d2));
 
 	enforce_ruleset(_metadata, ruleset_fd);
@@ -1662,9 +1912,15 @@
 	ASSERT_EQ(-1, renameat2(AT_FDCWD, dir_s2d2, AT_FDCWD, file1_s2d1,
 				RENAME_EXCHANGE));
 	ASSERT_EQ(EACCES, errno);
+	/* Checks that file1_s2d1 cannot be removed (instead of ENOTDIR). */
+	ASSERT_EQ(-1, rename(dir_s2d2, file1_s2d1));
+	ASSERT_EQ(EACCES, errno);
 	ASSERT_EQ(-1, renameat2(AT_FDCWD, file1_s2d1, AT_FDCWD, dir_s2d2,
 				RENAME_EXCHANGE));
 	ASSERT_EQ(EACCES, errno);
+	/* Checks that file1_s1d1 cannot be removed (instead of EISDIR). */
+	ASSERT_EQ(-1, rename(file1_s1d1, dir_s1d2));
+	ASSERT_EQ(EACCES, errno);
 
 	/* Renames files with different parents. */
 	ASSERT_EQ(-1, rename(file1_s2d2, file1_s1d2));
@@ -1675,14 +1931,14 @@
 
 	/* Exchanges and renames files with same parent. */
 	ASSERT_EQ(0, renameat2(AT_FDCWD, file2_s2d3, AT_FDCWD, file1_s2d3,
-				RENAME_EXCHANGE));
+			       RENAME_EXCHANGE));
 	ASSERT_EQ(0, rename(file2_s2d3, file1_s2d3));
 
 	/* Exchanges files and directories with same parent, twice. */
 	ASSERT_EQ(0, renameat2(AT_FDCWD, file1_s2d2, AT_FDCWD, dir_s2d3,
-				RENAME_EXCHANGE));
+			       RENAME_EXCHANGE));
 	ASSERT_EQ(0, renameat2(AT_FDCWD, file1_s2d2, AT_FDCWD, dir_s2d3,
-				RENAME_EXCHANGE));
+			       RENAME_EXCHANGE));
 }
 
 TEST_F_FORK(layout1, rename_dir)
@@ -1696,10 +1952,10 @@
 			.path = dir_s2d1,
 			.access = LANDLOCK_ACCESS_FS_REMOVE_DIR,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 
@@ -1727,16 +1983,22 @@
 	ASSERT_EQ(-1, renameat2(AT_FDCWD, dir_s1d1, AT_FDCWD, dir_s2d1,
 				RENAME_EXCHANGE));
 	ASSERT_EQ(EACCES, errno);
+	/* Checks that dir_s1d2 cannot be removed (instead of ENOTDIR). */
+	ASSERT_EQ(-1, rename(dir_s1d2, file1_s1d1));
+	ASSERT_EQ(EACCES, errno);
 	ASSERT_EQ(-1, renameat2(AT_FDCWD, file1_s1d1, AT_FDCWD, dir_s1d2,
 				RENAME_EXCHANGE));
 	ASSERT_EQ(EACCES, errno);
+	/* Checks that dir_s1d2 cannot be removed (instead of EISDIR). */
+	ASSERT_EQ(-1, rename(file1_s1d1, dir_s1d2));
+	ASSERT_EQ(EACCES, errno);
 
 	/*
 	 * Exchanges and renames directory to the same parent, which allows
 	 * directory removal.
 	 */
 	ASSERT_EQ(0, renameat2(AT_FDCWD, dir_s1d3, AT_FDCWD, file1_s1d2,
-				RENAME_EXCHANGE));
+			       RENAME_EXCHANGE));
 	ASSERT_EQ(0, unlink(dir_s1d3));
 	ASSERT_EQ(0, mkdir(dir_s1d3, 0700));
 	ASSERT_EQ(0, rename(file1_s1d2, dir_s1d3));
@@ -1750,10 +2012,10 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_REMOVE_DIR,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 
@@ -1787,10 +2049,10 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_REMOVE_FILE,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
@@ -1805,14 +2067,15 @@
 }
 
 static void test_make_file(struct __test_metadata *const _metadata,
-		const __u64 access, const mode_t mode, const dev_t dev)
+			   const __u64 access, const mode_t mode,
+			   const dev_t dev)
 {
 	const struct rule rules[] = {
 		{
 			.path = dir_s1d2,
 			.access = access,
 		},
-		{}
+		{},
 	};
 	const int ruleset_fd = create_ruleset(_metadata, access, rules);
 
@@ -1820,9 +2083,10 @@
 
 	ASSERT_EQ(0, unlink(file1_s1d1));
 	ASSERT_EQ(0, unlink(file2_s1d1));
-	ASSERT_EQ(0, mknod(file2_s1d1, mode | 0400, dev)) {
-		TH_LOG("Failed to make file \"%s\": %s",
-				file2_s1d1, strerror(errno));
+	ASSERT_EQ(0, mknod(file2_s1d1, mode | 0400, dev))
+	{
+		TH_LOG("Failed to make file \"%s\": %s", file2_s1d1,
+		       strerror(errno));
 	};
 
 	ASSERT_EQ(0, unlink(file1_s1d2));
@@ -1841,9 +2105,10 @@
 	ASSERT_EQ(-1, rename(file2_s1d1, file1_s1d1));
 	ASSERT_EQ(EACCES, errno);
 
-	ASSERT_EQ(0, mknod(file1_s1d2, mode | 0400, dev)) {
-		TH_LOG("Failed to make file \"%s\": %s",
-				file1_s1d2, strerror(errno));
+	ASSERT_EQ(0, mknod(file1_s1d2, mode | 0400, dev))
+	{
+		TH_LOG("Failed to make file \"%s\": %s", file1_s1d2,
+		       strerror(errno));
 	};
 	ASSERT_EQ(0, link(file1_s1d2, file2_s1d2));
 	ASSERT_EQ(0, unlink(file2_s1d2));
@@ -1860,7 +2125,7 @@
 	/* Creates a /dev/null device. */
 	set_cap(_metadata, CAP_MKNOD);
 	test_make_file(_metadata, LANDLOCK_ACCESS_FS_MAKE_CHAR, S_IFCHR,
-			makedev(1, 3));
+		       makedev(1, 3));
 }
 
 TEST_F_FORK(layout1, make_block)
@@ -1868,7 +2133,7 @@
 	/* Creates a /dev/loop0 device. */
 	set_cap(_metadata, CAP_MKNOD);
 	test_make_file(_metadata, LANDLOCK_ACCESS_FS_MAKE_BLOCK, S_IFBLK,
-			makedev(7, 0));
+		       makedev(7, 0));
 }
 
 TEST_F_FORK(layout1, make_reg_1)
@@ -1898,10 +2163,10 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_MAKE_SYM,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 
@@ -1943,10 +2208,10 @@
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_MAKE_DIR,
 		},
-		{}
+		{},
 	};
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 
@@ -1965,12 +2230,12 @@
 }
 
 static int open_proc_fd(struct __test_metadata *const _metadata, const int fd,
-		const int open_flags)
+			const int open_flags)
 {
 	static const char path_template[] = "/proc/self/fd/%d";
 	char procfd_path[sizeof(path_template) + 10];
-	const int procfd_path_size = snprintf(procfd_path, sizeof(procfd_path),
-			path_template, fd);
+	const int procfd_path_size =
+		snprintf(procfd_path, sizeof(procfd_path), path_template, fd);
 
 	ASSERT_LT(procfd_path_size, sizeof(procfd_path));
 	return open(procfd_path, open_flags);
@@ -1983,12 +2248,13 @@
 			.path = file1_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	int reg_fd, proc_fd;
-	const int ruleset_fd = create_ruleset(_metadata,
-			LANDLOCK_ACCESS_FS_READ_FILE |
-			LANDLOCK_ACCESS_FS_WRITE_FILE, rules);
+	const int ruleset_fd = create_ruleset(
+		_metadata,
+		LANDLOCK_ACCESS_FS_READ_FILE | LANDLOCK_ACCESS_FS_WRITE_FILE,
+		rules);
 
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
@@ -2005,9 +2271,10 @@
 	ASSERT_EQ(0, close(proc_fd));
 
 	proc_fd = open_proc_fd(_metadata, reg_fd, O_RDWR | O_CLOEXEC);
-	ASSERT_EQ(-1, proc_fd) {
-		TH_LOG("Successfully opened /proc/self/fd/%d: %s",
-				reg_fd, strerror(errno));
+	ASSERT_EQ(-1, proc_fd)
+	{
+		TH_LOG("Successfully opened /proc/self/fd/%d: %s", reg_fd,
+		       strerror(errno));
 	}
 	ASSERT_EQ(EACCES, errno);
 
@@ -2023,13 +2290,13 @@
 		{
 			.path = dir_s1d2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	/* Limits read and write access to files tied to the filesystem. */
-	const int ruleset_fd = create_ruleset(_metadata, rules[0].access,
-			rules);
+	const int ruleset_fd =
+		create_ruleset(_metadata, rules[0].access, rules);
 
 	ASSERT_LE(0, ruleset_fd);
 	enforce_ruleset(_metadata, ruleset_fd);
@@ -2041,7 +2308,8 @@
 
 	/* Checks access to pipes through FD. */
 	ASSERT_EQ(0, pipe2(pipe_fds, O_CLOEXEC));
-	ASSERT_EQ(1, write(pipe_fds[1], ".", 1)) {
+	ASSERT_EQ(1, write(pipe_fds[1], ".", 1))
+	{
 		TH_LOG("Failed to write in pipe: %s", strerror(errno));
 	}
 	ASSERT_EQ(1, read(pipe_fds[0], &buf, 1));
@@ -2050,9 +2318,10 @@
 	/* Checks write access to pipe through /proc/self/fd . */
 	proc_fd = open_proc_fd(_metadata, pipe_fds[1], O_WRONLY | O_CLOEXEC);
 	ASSERT_LE(0, proc_fd);
-	ASSERT_EQ(1, write(proc_fd, ".", 1)) {
+	ASSERT_EQ(1, write(proc_fd, ".", 1))
+	{
 		TH_LOG("Failed to write through /proc/self/fd/%d: %s",
-				pipe_fds[1], strerror(errno));
+		       pipe_fds[1], strerror(errno));
 	}
 	ASSERT_EQ(0, close(proc_fd));
 
@@ -2060,9 +2329,10 @@
 	proc_fd = open_proc_fd(_metadata, pipe_fds[0], O_RDONLY | O_CLOEXEC);
 	ASSERT_LE(0, proc_fd);
 	buf = '\0';
-	ASSERT_EQ(1, read(proc_fd, &buf, 1)) {
+	ASSERT_EQ(1, read(proc_fd, &buf, 1))
+	{
 		TH_LOG("Failed to read through /proc/self/fd/%d: %s",
-				pipe_fds[1], strerror(errno));
+		       pipe_fds[1], strerror(errno));
 	}
 	ASSERT_EQ(0, close(proc_fd));
 
@@ -2070,8 +2340,9 @@
 	ASSERT_EQ(0, close(pipe_fds[1]));
 }
 
-FIXTURE(layout1_bind) {
-};
+/* clang-format off */
+FIXTURE(layout1_bind) {};
+/* clang-format on */
 
 FIXTURE_SETUP(layout1_bind)
 {
@@ -2161,7 +2432,7 @@
 			.path = dir_s2d1,
 			.access = ACCESS_RW,
 		},
-		{}
+		{},
 	};
 	/*
 	 * Sets access rights on the same bind-mounted directories.  The result
@@ -2177,7 +2448,7 @@
 			.path = dir_s2d2,
 			.access = ACCESS_RW,
 		},
-		{}
+		{},
 	};
 	/* Only allow read-access to the s1d3 hierarchies. */
 	const struct rule layer3_source[] = {
@@ -2185,7 +2456,7 @@
 			.path = dir_s1d3,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE,
 		},
-		{}
+		{},
 	};
 	/* Removes all access rights. */
 	const struct rule layer4_destination[] = {
@@ -2193,7 +2464,7 @@
 			.path = bind_file1_s1d3,
 			.access = LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd;
 
@@ -2282,8 +2553,8 @@
 	ASSERT_EQ(EACCES, test_open(bind_file1_s1d3, O_WRONLY));
 }
 
-#define LOWER_BASE	TMP_DIR "/lower"
-#define LOWER_DATA	LOWER_BASE "/data"
+#define LOWER_BASE TMP_DIR "/lower"
+#define LOWER_DATA LOWER_BASE "/data"
 static const char lower_fl1[] = LOWER_DATA "/fl1";
 static const char lower_dl1[] = LOWER_DATA "/dl1";
 static const char lower_dl1_fl2[] = LOWER_DATA "/dl1/fl2";
@@ -2295,23 +2566,23 @@
 static const char (*lower_base_files[])[] = {
 	&lower_fl1,
 	&lower_fo1,
-	NULL
+	NULL,
 };
 static const char (*lower_base_directories[])[] = {
 	&lower_dl1,
 	&lower_do1,
-	NULL
+	NULL,
 };
 static const char (*lower_sub_files[])[] = {
 	&lower_dl1_fl2,
 	&lower_do1_fo2,
 	&lower_do1_fl3,
-	NULL
+	NULL,
 };
 
-#define UPPER_BASE	TMP_DIR "/upper"
-#define UPPER_DATA	UPPER_BASE "/data"
-#define UPPER_WORK	UPPER_BASE "/work"
+#define UPPER_BASE TMP_DIR "/upper"
+#define UPPER_DATA UPPER_BASE "/data"
+#define UPPER_WORK UPPER_BASE "/work"
 static const char upper_fu1[] = UPPER_DATA "/fu1";
 static const char upper_du1[] = UPPER_DATA "/du1";
 static const char upper_du1_fu2[] = UPPER_DATA "/du1/fu2";
@@ -2323,22 +2594,22 @@
 static const char (*upper_base_files[])[] = {
 	&upper_fu1,
 	&upper_fo1,
-	NULL
+	NULL,
 };
 static const char (*upper_base_directories[])[] = {
 	&upper_du1,
 	&upper_do1,
-	NULL
+	NULL,
 };
 static const char (*upper_sub_files[])[] = {
 	&upper_du1_fu2,
 	&upper_do1_fo2,
 	&upper_do1_fu3,
-	NULL
+	NULL,
 };
 
-#define MERGE_BASE	TMP_DIR "/merge"
-#define MERGE_DATA	MERGE_BASE "/data"
+#define MERGE_BASE TMP_DIR "/merge"
+#define MERGE_DATA MERGE_BASE "/data"
 static const char merge_fl1[] = MERGE_DATA "/fl1";
 static const char merge_dl1[] = MERGE_DATA "/dl1";
 static const char merge_dl1_fl2[] = MERGE_DATA "/dl1/fl2";
@@ -2355,21 +2626,17 @@
 	&merge_fl1,
 	&merge_fu1,
 	&merge_fo1,
-	NULL
+	NULL,
 };
 static const char (*merge_base_directories[])[] = {
 	&merge_dl1,
 	&merge_du1,
 	&merge_do1,
-	NULL
+	NULL,
 };
 static const char (*merge_sub_files[])[] = {
-	&merge_dl1_fl2,
-	&merge_du1_fu2,
-	&merge_do1_fo2,
-	&merge_do1_fl3,
-	&merge_do1_fu3,
-	NULL
+	&merge_dl1_fl2, &merge_du1_fu2, &merge_do1_fo2,
+	&merge_do1_fl3, &merge_do1_fu3, NULL,
 };
 
 /*
@@ -2411,11 +2678,15 @@
  *         └── work
  */
 
-FIXTURE(layout2_overlay) {
-};
+/* clang-format off */
+FIXTURE(layout2_overlay) {};
+/* clang-format on */
 
 FIXTURE_SETUP(layout2_overlay)
 {
+	if (!supports_overlayfs())
+		SKIP(return, "overlayfs is not supported");
+
 	prepare_layout(_metadata);
 
 	create_directory(_metadata, LOWER_BASE);
@@ -2444,15 +2715,17 @@
 	set_cap(_metadata, CAP_SYS_ADMIN);
 	set_cap(_metadata, CAP_DAC_OVERRIDE);
 	ASSERT_EQ(0, mount("overlay", MERGE_DATA, "overlay", 0,
-				"lowerdir=" LOWER_DATA
-				",upperdir=" UPPER_DATA
-				",workdir=" UPPER_WORK));
+			   "lowerdir=" LOWER_DATA ",upperdir=" UPPER_DATA
+			   ",workdir=" UPPER_WORK));
 	clear_cap(_metadata, CAP_DAC_OVERRIDE);
 	clear_cap(_metadata, CAP_SYS_ADMIN);
 }
 
 FIXTURE_TEARDOWN(layout2_overlay)
 {
+	if (!supports_overlayfs())
+		SKIP(return, "overlayfs is not supported");
+
 	EXPECT_EQ(0, remove_path(lower_do1_fl3));
 	EXPECT_EQ(0, remove_path(lower_dl1_fl2));
 	EXPECT_EQ(0, remove_path(lower_fl1));
@@ -2484,6 +2757,9 @@
 
 TEST_F_FORK(layout2_overlay, no_restriction)
 {
+	if (!supports_overlayfs())
+		SKIP(return, "overlayfs is not supported");
+
 	ASSERT_EQ(0, test_open(lower_fl1, O_RDONLY));
 	ASSERT_EQ(0, test_open(lower_dl1, O_RDONLY));
 	ASSERT_EQ(0, test_open(lower_dl1_fl2, O_RDONLY));
@@ -2513,9 +2789,9 @@
 	ASSERT_EQ(0, test_open(merge_do1_fu3, O_RDONLY));
 }
 
-#define for_each_path(path_list, path_entry, i)			\
-	for (i = 0, path_entry = *path_list[i]; path_list[i];	\
-			path_entry = *path_list[++i])
+#define for_each_path(path_list, path_entry, i)               \
+	for (i = 0, path_entry = *path_list[i]; path_list[i]; \
+	     path_entry = *path_list[++i])
 
 TEST_F_FORK(layout2_overlay, same_content_different_file)
 {
@@ -2533,7 +2809,7 @@
 			.path = MERGE_BASE,
 			.access = ACCESS_RW,
 		},
-		{}
+		{},
 	};
 	const struct rule layer2_data[] = {
 		{
@@ -2548,7 +2824,7 @@
 			.path = MERGE_DATA,
 			.access = ACCESS_RW,
 		},
-		{}
+		{},
 	};
 	/* Sets access right on directories inside both layers. */
 	const struct rule layer3_subdirs[] = {
@@ -2580,7 +2856,7 @@
 			.path = merge_do1,
 			.access = ACCESS_RW,
 		},
-		{}
+		{},
 	};
 	/* Tighten access rights to the files. */
 	const struct rule layer4_files[] = {
@@ -2611,42 +2887,45 @@
 		{
 			.path = merge_dl1_fl2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
 		{
 			.path = merge_du1_fu2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
 		{
 			.path = merge_do1_fo2,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
 		{
 			.path = merge_do1_fl3,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
 		{
 			.path = merge_do1_fu3,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	const struct rule layer5_merge_only[] = {
 		{
 			.path = MERGE_DATA,
 			.access = LANDLOCK_ACCESS_FS_READ_FILE |
-				LANDLOCK_ACCESS_FS_WRITE_FILE,
+				  LANDLOCK_ACCESS_FS_WRITE_FILE,
 		},
-		{}
+		{},
 	};
 	int ruleset_fd;
 	size_t i;
 	const char *path_entry;
 
+	if (!supports_overlayfs())
+		SKIP(return, "overlayfs is not supported");
+
 	/* Sets rules on base directories (i.e. outside overlay scope). */
 	ruleset_fd = create_ruleset(_metadata, ACCESS_RW, layer1_base);
 	ASSERT_LE(0, ruleset_fd);
@@ -2659,7 +2938,8 @@
 		ASSERT_EQ(EACCES, test_open(path_entry, O_WRONLY));
 	}
 	for_each_path(lower_base_directories, path_entry, i) {
-		ASSERT_EQ(EACCES, test_open(path_entry, O_RDONLY | O_DIRECTORY));
+		ASSERT_EQ(EACCES,
+			  test_open(path_entry, O_RDONLY | O_DIRECTORY));
 	}
 	for_each_path(lower_sub_files, path_entry, i) {
 		ASSERT_EQ(0, test_open(path_entry, O_RDONLY));
@@ -2671,7 +2951,8 @@
 		ASSERT_EQ(EACCES, test_open(path_entry, O_WRONLY));
 	}
 	for_each_path(upper_base_directories, path_entry, i) {
-		ASSERT_EQ(EACCES, test_open(path_entry, O_RDONLY | O_DIRECTORY));
+		ASSERT_EQ(EACCES,
+			  test_open(path_entry, O_RDONLY | O_DIRECTORY));
 	}
 	for_each_path(upper_sub_files, path_entry, i) {
 		ASSERT_EQ(0, test_open(path_entry, O_RDONLY));
@@ -2756,7 +3037,8 @@
 		ASSERT_EQ(EACCES, test_open(path_entry, O_RDWR));
 	}
 	for_each_path(merge_base_directories, path_entry, i) {
-		ASSERT_EQ(EACCES, test_open(path_entry, O_RDONLY | O_DIRECTORY));
+		ASSERT_EQ(EACCES,
+			  test_open(path_entry, O_RDONLY | O_DIRECTORY));
 	}
 	for_each_path(merge_sub_files, path_entry, i) {
 		ASSERT_EQ(0, test_open(path_entry, O_RDWR));
@@ -2781,7 +3063,8 @@
 		ASSERT_EQ(EACCES, test_open(path_entry, O_RDWR));
 	}
 	for_each_path(merge_base_directories, path_entry, i) {
-		ASSERT_EQ(EACCES, test_open(path_entry, O_RDONLY | O_DIRECTORY));
+		ASSERT_EQ(EACCES,
+			  test_open(path_entry, O_RDONLY | O_DIRECTORY));
 	}
 	for_each_path(merge_sub_files, path_entry, i) {
 		ASSERT_EQ(0, test_open(path_entry, O_RDWR));
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/landlock/ptrace_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/landlock/ptrace_test.c
@@ -19,6 +19,12 @@
 
 #include "common.h"
 
+/* Copied from security/yama/yama_lsm.c */
+#define YAMA_SCOPE_DISABLED 0
+#define YAMA_SCOPE_RELATIONAL 1
+#define YAMA_SCOPE_CAPABILITY 2
+#define YAMA_SCOPE_NO_ATTACH 3
+
 static void create_domain(struct __test_metadata *const _metadata)
 {
 	int ruleset_fd;
@@ -26,9 +32,10 @@
 		.handled_access_fs = LANDLOCK_ACCESS_FS_MAKE_BLOCK,
 	};
 
-	ruleset_fd = landlock_create_ruleset(&ruleset_attr,
-			sizeof(ruleset_attr), 0);
-	EXPECT_LE(0, ruleset_fd) {
+	ruleset_fd =
+		landlock_create_ruleset(&ruleset_attr, sizeof(ruleset_attr), 0);
+	EXPECT_LE(0, ruleset_fd)
+	{
 		TH_LOG("Failed to create a ruleset: %s", strerror(errno));
 	}
 	EXPECT_EQ(0, prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0));
@@ -43,7 +50,7 @@
 	int procenv_path_size, fd;
 
 	procenv_path_size = snprintf(procenv_path, sizeof(procenv_path),
-			path_template, pid);
+				     path_template, pid);
 	if (procenv_path_size >= sizeof(procenv_path))
 		return E2BIG;
 
@@ -59,9 +66,31 @@
 	return 0;
 }
 
-FIXTURE(hierarchy) { };
+static int get_yama_ptrace_scope(void)
+{
+	int ret;
+	char buf[2] = {};
+	const int fd = open("/proc/sys/kernel/yama/ptrace_scope", O_RDONLY);
+
+	if (fd < 0)
+		return 0;
+
+	if (read(fd, buf, 1) < 0) {
+		close(fd);
+		return -1;
+	}
+
+	ret = atoi(buf);
+	close(fd);
+	return ret;
+}
+
+/* clang-format off */
+FIXTURE(hierarchy) {};
+/* clang-format on */
 
-FIXTURE_VARIANT(hierarchy) {
+FIXTURE_VARIANT(hierarchy)
+{
 	const bool domain_both;
 	const bool domain_parent;
 	const bool domain_child;
@@ -83,7 +112,9 @@
  *       \              P2 -> P1 : allow
  *        'P2
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, allow_without_domain) {
+	/* clang-format on */
 	.domain_both = false,
 	.domain_parent = false,
 	.domain_child = false,
@@ -98,7 +129,9 @@
  *        |  P2  |
  *        '------'
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, allow_with_one_domain) {
+	/* clang-format on */
 	.domain_both = false,
 	.domain_parent = false,
 	.domain_child = true,
@@ -112,7 +145,9 @@
  *            '
  *            P2
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, deny_with_parent_domain) {
+	/* clang-format on */
 	.domain_both = false,
 	.domain_parent = true,
 	.domain_child = false,
@@ -127,7 +162,9 @@
  *         |  P2  |
  *         '------'
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, deny_with_sibling_domain) {
+	/* clang-format on */
 	.domain_both = false,
 	.domain_parent = true,
 	.domain_child = true,
@@ -142,7 +179,9 @@
  * |         P2  |
  * '-------------'
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, allow_sibling_domain) {
+	/* clang-format on */
 	.domain_both = true,
 	.domain_parent = false,
 	.domain_child = false,
@@ -158,7 +197,9 @@
  * |        '------' |
  * '-----------------'
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, allow_with_nested_domain) {
+	/* clang-format on */
 	.domain_both = true,
 	.domain_parent = false,
 	.domain_child = true,
@@ -174,7 +215,9 @@
  * |             P2  |
  * '-----------------'
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, deny_with_nested_and_parent_domain) {
+	/* clang-format on */
 	.domain_both = true,
 	.domain_parent = true,
 	.domain_child = false,
@@ -192,17 +235,21 @@
  * |        '------' |
  * '-----------------'
  */
+/* clang-format off */
 FIXTURE_VARIANT_ADD(hierarchy, deny_with_forked_domain) {
+	/* clang-format on */
 	.domain_both = true,
 	.domain_parent = true,
 	.domain_child = true,
 };
 
 FIXTURE_SETUP(hierarchy)
-{ }
+{
+}
 
 FIXTURE_TEARDOWN(hierarchy)
-{ }
+{
+}
 
 /* Test PTRACE_TRACEME and PTRACE_ATTACH for parent and child. */
 TEST_F(hierarchy, trace)
@@ -210,8 +257,51 @@
 	pid_t child, parent;
 	int status, err_proc_read;
 	int pipe_child[2], pipe_parent[2];
+	int yama_ptrace_scope;
 	char buf_parent;
 	long ret;
+	bool can_read_child, can_trace_child, can_read_parent, can_trace_parent;
+
+	yama_ptrace_scope = get_yama_ptrace_scope();
+	ASSERT_LE(0, yama_ptrace_scope);
+
+	if (yama_ptrace_scope > YAMA_SCOPE_DISABLED)
+		TH_LOG("Incomplete tests due to Yama restrictions (scope %d)",
+		       yama_ptrace_scope);
+
+	/*
+	 * can_read_child is true if a parent process can read its child
+	 * process, which is only the case when the parent process is not
+	 * isolated from the child with a dedicated Landlock domain.
+	 */
+	can_read_child = !variant->domain_parent;
+
+	/*
+	 * can_trace_child is true if a parent process can trace its child
+	 * process.  This depends on two conditions:
+	 * - The parent process is not isolated from the child with a dedicated
+	 *   Landlock domain.
+	 * - Yama allows tracing children (up to YAMA_SCOPE_RELATIONAL).
+	 */
+	can_trace_child = can_read_child &&
+			  yama_ptrace_scope <= YAMA_SCOPE_RELATIONAL;
+
+	/*
+	 * can_read_parent is true if a child process can read its parent
+	 * process, which is only the case when the child process is not
+	 * isolated from the parent with a dedicated Landlock domain.
+	 */
+	can_read_parent = !variant->domain_child;
+
+	/*
+	 * can_trace_parent is true if a child process can trace its parent
+	 * process.  This depends on two conditions:
+	 * - The child process is not isolated from the parent with a dedicated
+	 *   Landlock domain.
+	 * - Yama is disabled (YAMA_SCOPE_DISABLED).
+	 */
+	can_trace_parent = can_read_parent &&
+			   yama_ptrace_scope <= YAMA_SCOPE_DISABLED;
 
 	/*
 	 * Removes all effective and permitted capabilities to not interfere
@@ -242,16 +332,21 @@
 		/* Waits for the parent to be in a domain, if any. */
 		ASSERT_EQ(1, read(pipe_parent[0], &buf_child, 1));
 
-		/* Tests PTRACE_ATTACH and PTRACE_MODE_READ on the parent. */
+		/* Tests PTRACE_MODE_READ on the parent. */
 		err_proc_read = test_ptrace_read(parent);
+		if (can_read_parent) {
+			EXPECT_EQ(0, err_proc_read);
+		} else {
+			EXPECT_EQ(EACCES, err_proc_read);
+		}
+
+		/* Tests PTRACE_ATTACH on the parent. */
 		ret = ptrace(PTRACE_ATTACH, parent, NULL, 0);
-		if (variant->domain_child) {
+		if (can_trace_parent) {
+			EXPECT_EQ(0, ret);
+		} else {
 			EXPECT_EQ(-1, ret);
 			EXPECT_EQ(EPERM, errno);
-			EXPECT_EQ(EACCES, err_proc_read);
-		} else {
-			EXPECT_EQ(0, ret);
-			EXPECT_EQ(0, err_proc_read);
 		}
 		if (ret == 0) {
 			ASSERT_EQ(parent, waitpid(parent, &status, 0));
@@ -261,11 +356,11 @@
 
 		/* Tests child PTRACE_TRACEME. */
 		ret = ptrace(PTRACE_TRACEME);
-		if (variant->domain_parent) {
+		if (can_trace_child) {
+			EXPECT_EQ(0, ret);
+		} else {
 			EXPECT_EQ(-1, ret);
 			EXPECT_EQ(EPERM, errno);
-		} else {
-			EXPECT_EQ(0, ret);
 		}
 
 		/*
@@ -274,7 +369,7 @@
 		 */
 		ASSERT_EQ(1, write(pipe_child[1], ".", 1));
 
-		if (!variant->domain_parent) {
+		if (can_trace_child) {
 			ASSERT_EQ(0, raise(SIGSTOP));
 		}
 
@@ -299,7 +394,7 @@
 	ASSERT_EQ(1, read(pipe_child[0], &buf_parent, 1));
 
 	/* Tests child PTRACE_TRACEME. */
-	if (!variant->domain_parent) {
+	if (can_trace_child) {
 		ASSERT_EQ(child, waitpid(child, &status, 0));
 		ASSERT_EQ(1, WIFSTOPPED(status));
 		ASSERT_EQ(0, ptrace(PTRACE_DETACH, child, NULL, 0));
@@ -309,17 +404,23 @@
 		EXPECT_EQ(ESRCH, errno);
 	}
 
-	/* Tests PTRACE_ATTACH and PTRACE_MODE_READ on the child. */
+	/* Tests PTRACE_MODE_READ on the child. */
 	err_proc_read = test_ptrace_read(child);
+	if (can_read_child) {
+		EXPECT_EQ(0, err_proc_read);
+	} else {
+		EXPECT_EQ(EACCES, err_proc_read);
+	}
+
+	/* Tests PTRACE_ATTACH on the child. */
 	ret = ptrace(PTRACE_ATTACH, child, NULL, 0);
-	if (variant->domain_parent) {
+	if (can_trace_child) {
+		EXPECT_EQ(0, ret);
+	} else {
 		EXPECT_EQ(-1, ret);
 		EXPECT_EQ(EPERM, errno);
-		EXPECT_EQ(EACCES, err_proc_read);
-	} else {
-		EXPECT_EQ(0, ret);
-		EXPECT_EQ(0, err_proc_read);
 	}
+
 	if (ret == 0) {
 		ASSERT_EQ(child, waitpid(child, &status, 0));
 		ASSERT_EQ(1, WIFSTOPPED(status));
@@ -330,7 +431,7 @@
 	ASSERT_EQ(1, write(pipe_parent[1], ".", 1));
 	ASSERT_EQ(child, waitpid(child, &status, 0));
 	if (WIFSIGNALED(status) || !WIFEXITED(status) ||
-			WEXITSTATUS(status) != EXIT_SUCCESS)
+	    WEXITSTATUS(status) != EXIT_SUCCESS)
 		_metadata->passed = 0;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/lib.mk
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/lib.mk
@@ -129,6 +129,11 @@
 clean:
 	$(CLEAN)
 
+# Enables to extend CFLAGS and LDFLAGS from command line, e.g.
+# make USERCFLAGS=-Werror USERLDFLAGS=-static
+CFLAGS += $(USERCFLAGS)
+LDFLAGS += $(USERLDFLAGS)
+
 # When make O= with kselftest target from main level
 # the following aren't defined.
 #
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/lkdtm/config
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/lkdtm/config
@@ -6,5 +6,6 @@
 # CONFIG_HARDENED_USERCOPY_FALLBACK is not set
 CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT=y
 CONFIG_INIT_ON_ALLOC_DEFAULT_ON=y
+CONFIG_UBSAN=y
 CONFIG_UBSAN_BOUNDS=y
 CONFIG_UBSAN_TRAP=y
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/lkdtm/stack-entropy.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/lkdtm/stack-entropy.sh
@@ -4,13 +4,27 @@
 # Measure kernel stack entropy by sampling via LKDTM's REPORT_STACK test.
 set -e
 samples="${1:-1000}"
+TRIGGER=/sys/kernel/debug/provoke-crash/DIRECT
+KSELFTEST_SKIP_TEST=4
+
+# Verify we have LKDTM available in the kernel.
+if [ ! -r $TRIGGER ] ; then
+	/sbin/modprobe -q lkdtm || true
+	if [ ! -r $TRIGGER ] ; then
+		echo "Cannot find $TRIGGER (missing CONFIG_LKDTM?)"
+	else
+		echo "Cannot write $TRIGGER (need to run as root?)"
+	fi
+	# Skip this test
+	exit $KSELFTEST_SKIP_TEST
+fi
 
 # Capture dmesg continuously since it may fill up depending on sample size.
 log=$(mktemp -t stack-entropy-XXXXXX)
 dmesg --follow >"$log" & pid=$!
 report=-1
 for i in $(seq 1 $samples); do
-        echo "REPORT_STACK" >/sys/kernel/debug/provoke-crash/DIRECT
+        echo "REPORT_STACK" > $TRIGGER
 	if [ -t 1 ]; then
 		percent=$(( 100 * $i / $samples ))
 		if [ "$percent" -ne "$report" ]; then
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/memfd/fuse_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/memfd/fuse_test.c
@@ -22,6 +22,7 @@
 #include <linux/falloc.h>
 #include <fcntl.h>
 #include <linux/memfd.h>
+#include <linux/types.h>
 #include <sched.h>
 #include <stdio.h>
 #include <stdlib.h>
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/memfd/memfd_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/memfd/memfd_test.c
@@ -455,6 +455,7 @@
 			printf("mmap()+mprotect() didn't fail as expected\n");
 			abort();
 		}
+		munmap(p, mfd_def_size);
 	}
 
 	/* verify PUNCH_HOLE fails */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/memory-hotplug/settings
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/memory-hotplug/settings
@@ -0,0 +1 @@
+timeout=600
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/mincore/mincore_selftest.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/mincore/mincore_selftest.c
@@ -207,15 +207,21 @@
 
 	errno = 0;
 	fd = open(".", O_TMPFILE | O_RDWR, 0600);
-	ASSERT_NE(-1, fd) {
-		TH_LOG("Can't create temporary file: %s",
-			strerror(errno));
+	if (fd < 0) {
+		ASSERT_EQ(errno, EOPNOTSUPP) {
+			TH_LOG("Can't create temporary file: %s",
+			       strerror(errno));
+		}
+		SKIP(goto out_free, "O_TMPFILE not supported by filesystem.");
 	}
 	errno = 0;
 	retval = fallocate(fd, 0, 0, FILE_SIZE);
-	ASSERT_EQ(0, retval) {
-		TH_LOG("Error allocating space for the temporary file: %s",
-			strerror(errno));
+	if (retval) {
+		ASSERT_EQ(errno, EOPNOTSUPP) {
+			TH_LOG("Error allocating space for the temporary file: %s",
+			       strerror(errno));
+		}
+		SKIP(goto out_close, "fallocate not supported by filesystem.");
 	}
 
 	/*
@@ -271,7 +277,9 @@
 	}
 
 	munmap(addr, FILE_SIZE);
+out_close:
 	close(fd);
+out_free:
 	free(vec);
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/mount_setattr/mount_setattr_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/mount_setattr/mount_setattr_test.c
@@ -18,6 +18,7 @@
 #include <grp.h>
 #include <stdbool.h>
 #include <stdarg.h>
+#include <linux/mount.h>
 
 #include "../kselftest_harness.h"
 
@@ -103,13 +104,6 @@
 	#else
 		#define __NR_mount_setattr 442
 	#endif
-
-struct mount_attr {
-	__u64 attr_set;
-	__u64 attr_clr;
-	__u64 propagation;
-	__u64 userns_fd;
-};
 #endif
 
 #ifndef __NR_open_tree
@@ -1032,7 +1026,7 @@
 			"size=100000,mode=700"), 0);
 
 	ASSERT_EQ(mount("testing", "/mnt", "tmpfs", MS_NOATIME | MS_NODEV,
-			"size=100000,mode=700"), 0);
+			"size=2m,mode=700"), 0);
 
 	ASSERT_EQ(mkdir("/mnt/A", 0777), 0);
 
@@ -1236,7 +1230,7 @@
 }
 
 /**
- * Validate that an attached mount in our mount namespace can be idmapped.
+ * Validate that an attached mount in our mount namespace cannot be idmapped.
  * (The kernel enforces that the mount's mount namespace and the caller's mount
  *  namespace match.)
  */
@@ -1259,7 +1253,7 @@
 
 	attr.userns_fd	= get_userns_fd(0, 10000, 10000);
 	ASSERT_GE(attr.userns_fd, 0);
-	ASSERT_EQ(sys_mount_setattr(open_tree_fd, "", AT_EMPTY_PATH, &attr, sizeof(attr)), 0);
+	ASSERT_NE(sys_mount_setattr(open_tree_fd, "", AT_EMPTY_PATH, &attr, sizeof(attr)), 0);
 	ASSERT_EQ(close(attr.userns_fd), 0);
 	ASSERT_EQ(close(open_tree_fd), 0);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/mqueue/mq_perf_tests.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/mqueue/mq_perf_tests.c
@@ -180,6 +180,9 @@
 	if (in_shutdown++)
 		return;
 
+	/* Free the cpu_set allocated using CPU_ALLOC in main function */
+	CPU_FREE(cpu_set);
+
 	for (i = 0; i < num_cpus_to_pin; i++)
 		if (cpu_threads[i]) {
 			pthread_kill(cpu_threads[i], SIGUSR1);
@@ -551,6 +554,12 @@
 		perror("sysconf(_SC_NPROCESSORS_ONLN)");
 		exit(1);
 	}
+
+	if (getuid() != 0)
+		ksft_exit_skip("Not running as root, but almost all tests "
+			"require root in order to modify\nsystem settings.  "
+			"Exiting.\n");
+
 	cpus_online = min(MAX_CPUS, sysconf(_SC_NPROCESSORS_ONLN));
 	cpu_set = CPU_ALLOC(cpus_online);
 	if (cpu_set == NULL) {
@@ -589,7 +598,7 @@
 						cpu_set)) {
 					fprintf(stderr, "Any given CPU may "
 						"only be given once.\n");
-					exit(1);
+					goto err_code;
 				} else
 					CPU_SET_S(cpus_to_pin[cpu],
 						  cpu_set_size, cpu_set);
@@ -607,7 +616,7 @@
 				queue_path = malloc(strlen(option) + 2);
 				if (!queue_path) {
 					perror("malloc()");
-					exit(1);
+					goto err_code;
 				}
 				queue_path[0] = '/';
 				queue_path[1] = 0;
@@ -622,17 +631,12 @@
 		fprintf(stderr, "Must pass at least one CPU to continuous "
 			"mode.\n");
 		poptPrintUsage(popt_context, stderr, 0);
-		exit(1);
+		goto err_code;
 	} else if (!continuous_mode) {
 		num_cpus_to_pin = 1;
 		cpus_to_pin[0] = cpus_online - 1;
 	}
 
-	if (getuid() != 0)
-		ksft_exit_skip("Not running as root, but almost all tests "
-			"require root in order to modify\nsystem settings.  "
-			"Exiting.\n");
-
 	max_msgs = fopen(MAX_MSGS, "r+");
 	max_msgsize = fopen(MAX_MSGSIZE, "r+");
 	if (!max_msgs)
@@ -740,4 +744,9 @@
 			sleep(1);
 	}
 	shutdown(0, "", 0);
+
+err_code:
+	CPU_FREE(cpu_set);
+	exit(1);
+
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/mqueue/setting
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/mqueue/setting
@@ -0,0 +1 @@
+timeout=180
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/Makefile
@@ -11,8 +11,8 @@
 TEST_PROGS += udpgro_bench.sh udpgro.sh test_vxlan_under_vrf.sh reuseport_addr_any.sh
 TEST_PROGS += test_vxlan_fdb_changelink.sh so_txtime.sh ipv6_flowlabel.sh
 TEST_PROGS += tcp_fastopen_backup_key.sh fcnal-test.sh l2tp.sh traceroute.sh
-TEST_PROGS += fin_ack_lat.sh fib_nexthop_multiprefix.sh fib_nexthops.sh
-TEST_PROGS += altnames.sh icmp_redirect.sh ip6_gre_headroom.sh
+TEST_PROGS += fin_ack_lat.sh fib_nexthop_multiprefix.sh fib_nexthops.sh fib_nexthop_nongw.sh
+TEST_PROGS += altnames.sh icmp.sh icmp_redirect.sh ip6_gre_headroom.sh
 TEST_PROGS += route_localnet.sh
 TEST_PROGS += reuseaddr_ports_exhausted.sh
 TEST_PROGS += txtimestamp.sh
@@ -28,7 +28,12 @@
 TEST_PROGS += ioam6.sh
 TEST_PROGS += gro.sh
 TEST_PROGS += gre_gso.sh
-TEST_PROGS_EXTENDED := in_netns.sh
+TEST_PROGS += srv6_end_dt46_l3vpn_test.sh
+TEST_PROGS += srv6_end_dt4_l3vpn_test.sh
+TEST_PROGS += srv6_end_dt6_l3vpn_test.sh
+TEST_PROGS += vrf_strict_mode_test.sh
+TEST_PROGS_EXTENDED := in_netns.sh setup_loopback.sh setup_veth.sh
+TEST_PROGS_EXTENDED += toeplitz_client.sh toeplitz.sh
 TEST_GEN_FILES =  socket nettest
 TEST_GEN_FILES += psock_fanout psock_tpacket msg_zerocopy reuseport_addr_any
 TEST_GEN_FILES += tcp_mmap tcp_inq psock_snd txring_overwrite
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/af_unix/test_unix_oob.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/af_unix/test_unix_oob.c
@@ -124,7 +124,7 @@
 
 	wait_for_signal(pipefd[0]);
 	if (connect(cfd, (struct sockaddr *)consumer_addr,
-		     sizeof(struct sockaddr)) != 0) {
+		     sizeof(*consumer_addr)) != 0) {
 		perror("Connect failed");
 		kill(0, SIGTERM);
 		exit(1);
@@ -218,10 +218,10 @@
 
 	/* Test 1:
 	 * veriyf that SIGURG is
-	 * delivered and 63 bytes are
-	 * read and oob is '@'
+	 * delivered, 63 bytes are
+	 * read, oob is '@', and POLLPRI works.
 	 */
-	wait_for_data(pfd, POLLIN | POLLPRI);
+	wait_for_data(pfd, POLLPRI);
 	read_oob(pfd, &oob);
 	len = read_data(pfd, buf, 1024);
 	if (!signal_recvd || len != 63 || oob != '@') {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/devlink_port_split.py
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/devlink_port_split.py
@@ -59,6 +59,8 @@
         assert stderr == ""
         ports = json.loads(stdout)['port']
 
+        validate_devlink_output(ports, 'flavour')
+
         for port in ports:
             if dev in port:
                 if ports[port]['flavour'] == 'physical':
@@ -220,6 +222,27 @@
     unsplit(port.bus_info)
 
 
+def validate_devlink_output(devlink_data, target_property=None):
+    """
+    Determine if test should be skipped by checking:
+      1. devlink_data contains values
+      2. The target_property exist in devlink_data
+    """
+    skip_reason = None
+    if any(devlink_data.values()):
+        if target_property:
+            skip_reason = "{} not found in devlink output, test skipped".format(target_property)
+            for key in devlink_data:
+                if target_property in devlink_data[key]:
+                    skip_reason = None
+    else:
+        skip_reason = 'devlink output is empty, test skipped'
+
+    if skip_reason:
+        print(skip_reason)
+        sys.exit(KSFT_SKIP)
+
+
 def make_parser():
     parser = argparse.ArgumentParser(description='A test for port splitting.')
     parser.add_argument('--dev',
@@ -240,12 +263,9 @@
         stdout, stderr = run_command(cmd)
         assert stderr == ""
 
+        validate_devlink_output(json.loads(stdout))
         devs = json.loads(stdout)['dev']
-        if devs:
-            dev = list(devs.keys())[0]
-        else:
-            print("no devlink device was found, test skipped")
-            sys.exit(KSFT_SKIP)
+        dev = list(devs.keys())[0]
 
     cmd = "devlink dev show %s" % dev
     stdout, stderr = run_command(cmd)
@@ -255,6 +275,7 @@
 
     ports = devlink_ports(dev)
 
+    found_max_lanes = False
     for port in ports.if_names:
         max_lanes = get_max_lanes(port.name)
 
@@ -277,6 +298,11 @@
                 split_splittable_port(port, lane, max_lanes, dev)
 
                 lane //= 2
+        found_max_lanes = True
+
+    if not found_max_lanes:
+        print(f"Test not started, no port of device {dev} reports max_lanes")
+        sys.exit(KSFT_SKIP)
 
 
 if __name__ == "__main__":
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/fcnal-test.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/fcnal-test.sh
@@ -84,6 +84,13 @@
 
 which ping6 > /dev/null 2>&1 && ping6=$(which ping6) || ping6=$(which ping)
 
+# Check if FIPS mode is enabled
+if [ -f /proc/sys/crypto/fips_enabled ]; then
+	fips_enabled=`cat /proc/sys/crypto/fips_enabled`
+else
+	fips_enabled=0
+fi
+
 ################################################################################
 # utilities
 
@@ -455,6 +462,22 @@
 	ip netns del ${NSC} >/dev/null 2>&1
 }
 
+cleanup_vrf_dup()
+{
+	ip link del ${NSA_DEV2} >/dev/null 2>&1
+	ip netns pids ${NSC} | xargs kill 2>/dev/null
+	ip netns del ${NSC} >/dev/null 2>&1
+}
+
+setup_vrf_dup()
+{
+	# some VRF tests use ns-C which has the same config as
+	# ns-B but for a device NOT in the VRF
+	create_ns ${NSC} "-" "-"
+	connect_ns ${NSA} ${NSA_DEV2} ${NSA_IP}/24 ${NSA_IP6}/64 \
+		   ${NSC} ${NSC_DEV} ${NSB_IP}/24 ${NSB_IP6}/64
+}
+
 setup()
 {
 	local with_vrf=${1}
@@ -484,12 +507,6 @@
 
 		ip -netns ${NSB} ro add ${VRF_IP}/32 via ${NSA_IP} dev ${NSB_DEV}
 		ip -netns ${NSB} -6 ro add ${VRF_IP6}/128 via ${NSA_IP6} dev ${NSB_DEV}
-
-		# some VRF tests use ns-C which has the same config as
-		# ns-B but for a device NOT in the VRF
-		create_ns ${NSC} "-" "-"
-		connect_ns ${NSA} ${NSA_DEV2} ${NSA_IP}/24 ${NSA_IP6}/64 \
-			   ${NSC} ${NSC_DEV} ${NSB_IP}/24 ${NSB_IP6}/64
 	else
 		ip -netns ${NSA} ro add ${NSB_LO_IP}/32 via ${NSB_IP} dev ${NSA_DEV}
 		ip -netns ${NSA} ro add ${NSB_LO_IP6}/128 via ${NSB_IP6} dev ${NSA_DEV}
@@ -733,7 +750,7 @@
 		log_start
 		show_hint "Fails since address on vrf device is out of device scope"
 		run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a}
-		log_test_addr ${a} $? 1 "ping local, device bind"
+		log_test_addr ${a} $? 2 "ping local, device bind"
 	done
 
 	#
@@ -793,10 +810,16 @@
 	setup
 	set_sysctl net.ipv4.raw_l3mdev_accept=1 2>/dev/null
 	ipv4_ping_novrf
+	setup
+	set_sysctl net.ipv4.ping_group_range='0 2147483647' 2>/dev/null
+	ipv4_ping_novrf
 
 	log_subsection "With VRF"
 	setup "yes"
 	ipv4_ping_vrf
+	setup "yes"
+	set_sysctl net.ipv4.ping_group_range='0 2147483647' 2>/dev/null
+	ipv4_ping_vrf
 }
 
 ################################################################################
@@ -1186,7 +1209,7 @@
 	run_cmd nettest -d ${NSA_DEV} -r ${a}
 	log_test_addr ${a} $? 1 "No server, device client, local conn"
 
-	ipv4_tcp_md5_novrf
+	[ "$fips_enabled" = "1" ] || ipv4_tcp_md5_novrf
 }
 
 ipv4_tcp_vrf()
@@ -1240,7 +1263,11 @@
 	log_test_addr ${a} $? 1 "Global server, local connection"
 
 	# run MD5 tests
-	ipv4_tcp_md5
+	if [ "$fips_enabled" = "0" ]; then
+		setup_vrf_dup
+		ipv4_tcp_md5
+		cleanup_vrf_dup
+	fi
 
 	#
 	# enable VRF global server
@@ -1798,8 +1825,9 @@
 	for a in ${NSA_IP} ${VRF_IP}
 	do
 		log_start
+		show_hint "Socket not bound to VRF, but address is in VRF"
 		run_cmd nettest -s -R -P icmp -l ${a} -b
-		log_test_addr ${a} $? 0 "Raw socket bind to local address"
+		log_test_addr ${a} $? 1 "Raw socket bind to local address"
 
 		log_start
 		run_cmd nettest -s -R -P icmp -l ${a} -I ${NSA_DEV} -b
@@ -2191,7 +2219,7 @@
 		log_start
 		show_hint "Fails since VRF device does not support linklocal or multicast"
 		run_cmd ${ping6} -c1 -w1 ${a}
-		log_test_addr ${a} $? 2 "ping out, VRF bind"
+		log_test_addr ${a} $? 1 "ping out, VRF bind"
 	done
 
 	for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} ${MCAST}%${NSA_DEV}
@@ -2311,10 +2339,16 @@
 	log_subsection "No VRF"
 	setup
 	ipv6_ping_novrf
+	setup
+	set_sysctl net.ipv4.ping_group_range='0 2147483647' 2>/dev/null
+	ipv6_ping_novrf
 
 	log_subsection "With VRF"
 	setup "yes"
 	ipv6_ping_vrf
+	setup "yes"
+	set_sysctl net.ipv4.ping_group_range='0 2147483647' 2>/dev/null
+	ipv6_ping_vrf
 }
 
 ################################################################################
@@ -2649,7 +2683,7 @@
 		log_test_addr ${a} $? 1 "No server, device client, local conn"
 	done
 
-	ipv6_tcp_md5_novrf
+	[ "$fips_enabled" = "1" ] || ipv6_tcp_md5_novrf
 }
 
 ipv6_tcp_vrf()
@@ -2719,7 +2753,11 @@
 	log_test_addr ${a} $? 1 "Global server, local connection"
 
 	# run MD5 tests
-	ipv6_tcp_md5
+	if [ "$fips_enabled" = "0" ]; then
+		setup_vrf_dup
+		ipv6_tcp_md5
+		cleanup_vrf_dup
+	fi
 
 	#
 	# enable VRF global server
@@ -3414,11 +3452,14 @@
 	run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b
 	log_test_addr ${a} $? 0 "TCP socket bind to local address after device bind"
 
+	# Sadly, the kernel allows binding a socket to a device and then
+	# binding to an address not on the device. So this test passes
+	# when it really should not
 	a=${NSA_LO_IP6}
 	log_start
-	show_hint "Should fail with 'Cannot assign requested address'"
+	show_hint "Tecnically should fail since address is not on device but kernel allows"
 	run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b
-	log_test_addr ${a} $? 1 "TCP socket bind to out of scope local address"
+	log_test_addr ${a} $? 0 "TCP socket bind to out of scope local address"
 }
 
 ipv6_addr_bind_vrf()
@@ -3459,10 +3500,15 @@
 	run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b
 	log_test_addr ${a} $? 0 "TCP socket bind to local address with device bind"
 
+	# Sadly, the kernel allows binding a socket to a device and then
+	# binding to an address not on the device. The only restriction
+	# is that the address is valid in the L3 domain. So this test
+	# passes when it really should not
 	a=${VRF_IP6}
 	log_start
+	show_hint "Tecnically should fail since address is not on device but kernel allows"
 	run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b
-	log_test_addr ${a} $? 1 "TCP socket bind to VRF address with device bind"
+	log_test_addr ${a} $? 0 "TCP socket bind to VRF address with device bind"
 
 	a=${NSA_LO_IP6}
 	log_start
@@ -4002,8 +4048,8 @@
 ################################################################################
 # main
 
-TESTS_IPV4="ipv4_ping ipv4_tcp ipv4_udp ipv4_addr_bind ipv4_runtime ipv4_netfilter"
-TESTS_IPV6="ipv6_ping ipv6_tcp ipv6_udp ipv6_addr_bind ipv6_runtime ipv6_netfilter"
+TESTS_IPV4="ipv4_ping ipv4_tcp ipv4_udp ipv4_bind ipv4_runtime ipv4_netfilter"
+TESTS_IPV6="ipv6_ping ipv6_tcp ipv6_udp ipv6_bind ipv6_runtime ipv6_netfilter"
 TESTS_OTHER="use_cases"
 
 PAUSE_ON_FAIL=no
@@ -4037,10 +4083,13 @@
 	TESTS="$TESTS_IPV6"
 fi
 
-which nettest >/dev/null
-if [ $? -ne 0 ]; then
-	echo "'nettest' command not found; skipping tests"
-	exit $ksft_skip
+# nettest can be run from PATH or from same directory as this selftest
+if ! which nettest >/dev/null; then
+	PATH=$PWD:$PATH
+	if ! which nettest >/dev/null; then
+		echo "'nettest' command not found; skipping tests"
+		exit $ksft_skip
+	fi
 fi
 
 declare -i nfail=0
@@ -4077,3 +4126,11 @@
 
 printf "\nTests passed: %3d\n" ${nsuccess}
 printf "Tests failed: %3d\n"   ${nfail}
+
+if [ $nfail -ne 0 ]; then
+	exit 1 # KSFT_FAIL
+elif [ $nsuccess -eq 0 ]; then
+	exit $ksft_skip
+fi
+
+exit 0 # KSFT_PASS
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/fib_nexthop_multiprefix.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/fib_nexthop_multiprefix.sh
@@ -209,12 +209,12 @@
 		echo "Route get"
 		ip -netns h0 -6 ro get ${dst}
 		echo "Searching for:"
-		echo "    ${dst} from :: via ${r1} dev eth0 src ${h0} .* mtu ${mtu}"
+		echo "    ${dst}.* via ${r1} dev eth0 src ${h0} .* mtu ${mtu}"
 		echo
 	fi
 
 	ip -netns h0 -6 ro get ${dst} | \
-	grep -q "${dst} from :: via ${r1} dev eth0 src ${h0} .* mtu ${mtu}"
+	grep -q "${dst}.* via ${r1} dev eth0 src ${h0} .* mtu ${mtu}"
 	rc=$?
 
 	log_test $rc 0 "IPv6: host 0 to host ${i}, mtu ${mtu}"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/fib_nexthop_nongw.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/fib_nexthop_nongw.sh
@@ -0,0 +1,119 @@
+#!/bin/bash
+# SPDX-License-Identifier: GPL-2.0
+#
+# ns: h1               | ns: h2
+#   192.168.0.1/24     |
+#            eth0      |
+#                      |       192.168.1.1/32
+#            veth0 <---|---> veth1
+# Validate source address selection for route without gateway
+
+PAUSE_ON_FAIL=no
+VERBOSE=0
+ret=0
+
+################################################################################
+# helpers
+
+log_test()
+{
+	local rc=$1
+	local expected=$2
+	local msg="$3"
+
+	if [ ${rc} -eq ${expected} ]; then
+		printf "TEST: %-60s  [ OK ]\n" "${msg}"
+		nsuccess=$((nsuccess+1))
+	else
+		ret=1
+		nfail=$((nfail+1))
+		printf "TEST: %-60s  [FAIL]\n" "${msg}"
+		if [ "${PAUSE_ON_FAIL}" = "yes" ]; then
+			echo
+			echo "hit enter to continue, 'q' to quit"
+			read a
+			[ "$a" = "q" ] && exit 1
+		fi
+	fi
+
+	[ "$VERBOSE" = "1" ] && echo
+}
+
+run_cmd()
+{
+	local cmd="$*"
+	local out
+	local rc
+
+	if [ "$VERBOSE" = "1" ]; then
+		echo "COMMAND: $cmd"
+	fi
+
+	out=$(eval $cmd 2>&1)
+	rc=$?
+	if [ "$VERBOSE" = "1" -a -n "$out" ]; then
+		echo "$out"
+	fi
+
+	[ "$VERBOSE" = "1" ] && echo
+
+	return $rc
+}
+
+################################################################################
+# config
+setup()
+{
+	ip netns add h1
+	ip -n h1 link set lo up
+	ip netns add h2
+	ip -n h2 link set lo up
+
+	# Add a fake eth0 to support an ip address
+	ip -n h1 link add name eth0 type dummy
+	ip -n h1 link set eth0 up
+	ip -n h1 address add 192.168.0.1/24 dev eth0
+
+	# Configure veths (same @mac, arp off)
+	ip -n h1 link add name veth0 type veth peer name veth1 netns h2
+	ip -n h1 link set veth0 up
+
+	ip -n h2 link set veth1 up
+
+	# Configure @IP in the peer netns
+	ip -n h2 address add 192.168.1.1/32 dev veth1
+	ip -n h2 route add default dev veth1
+
+	# Add a nexthop without @gw and use it in a route
+	ip -n h1 nexthop add id 1 dev veth0
+	ip -n h1 route add 192.168.1.1 nhid 1
+}
+
+cleanup()
+{
+	ip netns del h1 2>/dev/null
+	ip netns del h2 2>/dev/null
+}
+
+trap cleanup EXIT
+
+################################################################################
+# main
+
+while getopts :pv o
+do
+	case $o in
+		p) PAUSE_ON_FAIL=yes;;
+		v) VERBOSE=1;;
+	esac
+done
+
+cleanup
+setup
+
+run_cmd ip -netns h1 route get 192.168.1.1
+log_test $? 0 "nexthop: get route with nexthop without gw"
+run_cmd ip netns exec h1 ping -c1 192.168.1.1
+log_test $? 0 "nexthop: ping through nexthop without gw"
+
+exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/fib_nexthops.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/fib_nexthops.sh
@@ -1145,6 +1145,36 @@
 	set +e
 	check_nexthop "dev veth1" ""
 	log_test $? 0 "Nexthops removed on admin down"
+
+	# nexthop route delete warning: route add with nhid and delete
+	# using device
+	run_cmd "$IP li set dev veth1 up"
+	run_cmd "$IP nexthop add id 12 via 172.16.1.3 dev veth1"
+	out1=`dmesg | grep "WARNING:.*fib_nh_match.*" | wc -l`
+	run_cmd "$IP route add 172.16.101.1/32 nhid 12"
+	run_cmd "$IP route delete 172.16.101.1/32 dev veth1"
+	out2=`dmesg | grep "WARNING:.*fib_nh_match.*" | wc -l`
+	[ $out1 -eq $out2 ]
+	rc=$?
+	log_test $rc 0 "Delete nexthop route warning"
+	run_cmd "$IP route delete 172.16.101.1/32 nhid 12"
+	run_cmd "$IP nexthop del id 12"
+
+	run_cmd "$IP nexthop add id 21 via 172.16.1.6 dev veth1"
+	run_cmd "$IP ro add 172.16.101.0/24 nhid 21"
+	run_cmd "$IP ro del 172.16.101.0/24 nexthop via 172.16.1.7 dev veth1 nexthop via 172.16.1.8 dev veth1"
+	log_test $? 2 "Delete multipath route with only nh id based entry"
+
+	run_cmd "$IP nexthop add id 22 via 172.16.1.6 dev veth1"
+	run_cmd "$IP ro add 172.16.102.0/24 nhid 22"
+	run_cmd "$IP ro del 172.16.102.0/24 dev veth1"
+	log_test $? 2 "Delete route when specifying only nexthop device"
+
+	run_cmd "$IP ro del 172.16.102.0/24 via 172.16.1.6"
+	log_test $? 2 "Delete route when specifying only gateway"
+
+	run_cmd "$IP ro del 172.16.102.0/24"
+	log_test $? 0 "Delete route when not specifying nexthop attributes"
 }
 
 ipv4_grp_fcnal()
@@ -1887,6 +1917,11 @@
 
 	run_cmd "$IP link set dev lo up"
 
+	# Dump should not loop endlessly when maximum nexthop ID is configured.
+	run_cmd "$IP nexthop add id $((2**32-1)) blackhole"
+	run_cmd "timeout 5 $IP nexthop"
+	log_test $? 0 "Maximum nexthop ID dump"
+
 	#
 	# groups
 	#
@@ -2078,6 +2113,7 @@
 		"id 101 index 0 nhid 2 id 101 index 1 nhid 2 id 101 index 2 nhid 1 id 101 index 3 nhid 1"
 	log_test $? 0 "Dump all nexthop buckets in a group"
 
+	sleep 0.1
 	(( $($IP -j nexthop bucket list id 101 |
 	     jq '[.[] | select(.bucket.idle_time > 0 and
 	                       .bucket.idle_time < 2)] | length') == 4 ))
@@ -2106,6 +2142,11 @@
 	run_cmd "$IP nexthop bucket list fdb"
 	log_test $? 255 "Dump all nexthop buckets with invalid 'fdb' keyword"
 
+	# Dump should not loop endlessly when maximum nexthop ID is configured.
+	run_cmd "$IP nexthop add id $((2**32-1)) group 1/2 type resilient buckets 4"
+	run_cmd "timeout 5 $IP nexthop bucket"
+	log_test $? 0 "Maximum nexthop ID dump"
+
 	#
 	# resilient nexthop buckets get requests
 	#
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/fib_rule_tests.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/fib_rule_tests.sh
@@ -62,6 +62,8 @@
 	$IP address add $DEV_ADDR/24 dev dummy0
 	$IP -6 address add $DEV_ADDR6/64 dev dummy0
 
+	ip netns exec testns sysctl -w net.ipv4.ip_forward=1
+
 	set +e
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/fib_tests.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/fib_tests.sh
@@ -68,7 +68,7 @@
 cleanup()
 {
 	$IP link del dev dummy0 &> /dev/null
-	ip netns del ns1
+	ip netns del ns1 &> /dev/null
 	ip netns del ns2 &> /dev/null
 }
 
@@ -444,24 +444,63 @@
 	setup
 
 	set -e
+	ip netns add ns2
+	ip netns set ns2 auto
+
+	ip -netns ns2 link set dev lo up
+
+	$IP link add name veth1 type veth peer name veth2
+	$IP link set dev veth2 netns ns2
+	$IP address add 192.0.2.1/24 dev veth1
+	ip -netns ns2 address add 192.0.2.1/24 dev veth2
+	$IP link set dev veth1 up
+	ip -netns ns2 link set dev veth2 up
+
 	$IP link set dev lo address 52:54:00:6a:c7:5e
-	$IP link set dummy0 address 52:54:00:6a:c7:5e
-	$IP link add dummy1 type dummy
-	$IP link set dummy1 address 52:54:00:6a:c7:5e
-	$IP link set dev dummy1 up
+	$IP link set dev veth1 address 52:54:00:6a:c7:5e
+	ip -netns ns2 link set dev lo address 52:54:00:6a:c7:5e
+	ip -netns ns2 link set dev veth2 address 52:54:00:6a:c7:5e
+
+	# 1. (ns2) redirect lo's egress to veth2's egress
+	ip netns exec ns2 tc qdisc add dev lo parent root handle 1: fq_codel
+	ip netns exec ns2 tc filter add dev lo parent 1: protocol arp basic \
+		action mirred egress redirect dev veth2
+	ip netns exec ns2 tc filter add dev lo parent 1: protocol ip basic \
+		action mirred egress redirect dev veth2
+
+	# 2. (ns1) redirect veth1's ingress to lo's ingress
+	$NS_EXEC tc qdisc add dev veth1 ingress
+	$NS_EXEC tc filter add dev veth1 ingress protocol arp basic \
+		action mirred ingress redirect dev lo
+	$NS_EXEC tc filter add dev veth1 ingress protocol ip basic \
+		action mirred ingress redirect dev lo
+
+	# 3. (ns1) redirect lo's egress to veth1's egress
+	$NS_EXEC tc qdisc add dev lo parent root handle 1: fq_codel
+	$NS_EXEC tc filter add dev lo parent 1: protocol arp basic \
+		action mirred egress redirect dev veth1
+	$NS_EXEC tc filter add dev lo parent 1: protocol ip basic \
+		action mirred egress redirect dev veth1
+
+	# 4. (ns2) redirect veth2's ingress to lo's ingress
+	ip netns exec ns2 tc qdisc add dev veth2 ingress
+	ip netns exec ns2 tc filter add dev veth2 ingress protocol arp basic \
+		action mirred ingress redirect dev lo
+	ip netns exec ns2 tc filter add dev veth2 ingress protocol ip basic \
+		action mirred ingress redirect dev lo
+
 	$NS_EXEC sysctl -qw net.ipv4.conf.all.rp_filter=1
 	$NS_EXEC sysctl -qw net.ipv4.conf.all.accept_local=1
 	$NS_EXEC sysctl -qw net.ipv4.conf.all.route_localnet=1
-
-	$NS_EXEC tc qd add dev dummy1 parent root handle 1: fq_codel
-	$NS_EXEC tc filter add dev dummy1 parent 1: protocol arp basic action mirred egress redirect dev lo
-	$NS_EXEC tc filter add dev dummy1 parent 1: protocol ip basic action mirred egress redirect dev lo
+	ip netns exec ns2 sysctl -qw net.ipv4.conf.all.rp_filter=1
+	ip netns exec ns2 sysctl -qw net.ipv4.conf.all.accept_local=1
+	ip netns exec ns2 sysctl -qw net.ipv4.conf.all.route_localnet=1
 	set +e
 
-	run_cmd "ip netns exec ns1 ping -I dummy1 -w1 -c1 198.51.100.1"
+	run_cmd "ip netns exec ns2 ping -w1 -c1 192.0.2.1"
 	log_test $? 0 "rp_filter passes local packets"
 
-	run_cmd "ip netns exec ns1 ping -I dummy1 -w1 -c1 127.0.0.1"
+	run_cmd "ip netns exec ns2 ping -w1 -c1 127.0.0.1"
 	log_test $? 0 "rp_filter passes loopback packets"
 
 	cleanup
@@ -1583,13 +1622,21 @@
 
 	$IP addr add dev dummy1 172.16.104.1/24
 	$IP addr add dev dummy1 172.16.104.11/24
+	$IP addr add dev dummy1 172.16.104.12/24
+	$IP addr add dev dummy1 172.16.104.13/24
 	$IP addr add dev dummy2 172.16.104.1/24
 	$IP addr add dev dummy2 172.16.104.11/24
+	$IP addr add dev dummy2 172.16.104.12/24
 	$IP route add 172.16.105.0/24 via 172.16.104.2 src 172.16.104.11
+	$IP route add 172.16.106.0/24 dev lo src 172.16.104.12
+	$IP route add table 0 172.16.107.0/24 via 172.16.104.2 src 172.16.104.13
 	$IP route add vrf red 172.16.105.0/24 via 172.16.104.2 src 172.16.104.11
+	$IP route add vrf red 172.16.106.0/24 dev lo src 172.16.104.12
 	set +e
 
 	# removing address from device in vrf should only remove route from vrf table
+	echo "    Regular FIB info"
+
 	$IP addr del dev dummy2 172.16.104.11/24
 	$IP ro ls vrf red | grep -q 172.16.105.0/24
 	log_test $? 1 "Route removed from VRF when source address deleted"
@@ -1607,6 +1654,35 @@
 	$IP ro ls vrf red | grep -q 172.16.105.0/24
 	log_test $? 0 "Route in VRF is not removed by address delete"
 
+	# removing address from device in vrf should only remove route from vrf
+	# table even when the associated fib info only differs in table ID
+	echo "    Identical FIB info with different table ID"
+
+	$IP addr del dev dummy2 172.16.104.12/24
+	$IP ro ls vrf red | grep -q 172.16.106.0/24
+	log_test $? 1 "Route removed from VRF when source address deleted"
+
+	$IP ro ls | grep -q 172.16.106.0/24
+	log_test $? 0 "Route in default VRF not removed"
+
+	$IP addr add dev dummy2 172.16.104.12/24
+	$IP route add vrf red 172.16.106.0/24 dev lo src 172.16.104.12
+
+	$IP addr del dev dummy1 172.16.104.12/24
+	$IP ro ls | grep -q 172.16.106.0/24
+	log_test $? 1 "Route removed in default VRF when source address deleted"
+
+	$IP ro ls vrf red | grep -q 172.16.106.0/24
+	log_test $? 0 "Route in VRF is not removed by address delete"
+
+	# removing address from device in default vrf should remove route from
+	# the default vrf even when route was inserted with a table ID of 0.
+	echo "    Table ID 0"
+
+	$IP addr del dev dummy1 172.16.104.13/24
+	$IP ro ls | grep -q 172.16.107.0/24
+	log_test $? 1 "Route removed in default VRF when source address deleted"
+
 	$IP li del dummy1
 	$IP li del dummy2
 	cleanup
@@ -1845,6 +1921,8 @@
 ################################################################################
 # main
 
+trap cleanup EXIT
+
 while getopts :t:pPhv o
 do
 	case $o in
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/bridge_igmp.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/bridge_igmp.sh
@@ -481,13 +481,18 @@
 	RET=0
 	local X=("192.0.2.20" "192.0.2.30")
 
-	# GMI should be 3 seconds
-	ip link set dev br0 type bridge mcast_query_interval 100 mcast_query_response_interval 100
+	# GMI should be 5 seconds
+	ip link set dev br0 type bridge mcast_query_interval 100 \
+					mcast_query_response_interval 100 \
+					mcast_membership_interval 500
 
 	v3exclude_prepare $h1 $ALL_MAC $ALL_GROUP
-	ip link set dev br0 type bridge mcast_query_interval 500 mcast_query_response_interval 500
+	ip link set dev br0 type bridge mcast_query_interval 500 \
+					mcast_query_response_interval 500 \
+					mcast_membership_interval 1500
+
 	$MZ $h1 -c 1 -b $ALL_MAC -B $ALL_GROUP -t ip "proto=2,p=$MZPKT_ALLOW2" -q
-	sleep 3
+	sleep 5
 	bridge -j -d -s mdb show dev br0 \
 		| jq -e ".[].mdb[] | \
 			 select(.grp == \"$TEST_GROUP\" and \
@@ -517,7 +522,8 @@
 	log_test "IGMPv3 group $TEST_GROUP exclude timeout"
 
 	ip link set dev br0 type bridge mcast_query_interval 12500 \
-					mcast_query_response_interval 1000
+					mcast_query_response_interval 1000 \
+					mcast_membership_interval 26000
 
 	v3cleanup $swp1 $TEST_GROUP
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/bridge_mld.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/bridge_mld.sh
@@ -478,13 +478,18 @@
 	RET=0
 	local X=("2001:db8:1::20" "2001:db8:1::30")
 
-	# GMI should be 3 seconds
-	ip link set dev br0 type bridge mcast_query_interval 100 mcast_query_response_interval 100
+	# GMI should be 5 seconds
+	ip link set dev br0 type bridge mcast_query_interval 100 \
+					mcast_query_response_interval 100 \
+					mcast_membership_interval 500
 
 	mldv2exclude_prepare $h1
-	ip link set dev br0 type bridge mcast_query_interval 500 mcast_query_response_interval 500
+	ip link set dev br0 type bridge mcast_query_interval 500 \
+					mcast_query_response_interval 500 \
+					mcast_membership_interval 1500
+
 	$MZ $h1 -c 1 $MZPKT_ALLOW2 -q
-	sleep 3
+	sleep 5
 	bridge -j -d -s mdb show dev br0 \
 		| jq -e ".[].mdb[] | \
 			 select(.grp == \"$TEST_GROUP\" and \
@@ -514,7 +519,8 @@
 	log_test "MLDv2 group $TEST_GROUP exclude timeout"
 
 	ip link set dev br0 type bridge mcast_query_interval 12500 \
-					mcast_query_response_interval 1000
+					mcast_query_response_interval 1000 \
+					mcast_membership_interval 26000
 
 	mldv2cleanup $swp1
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/custom_multipath_hash.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/custom_multipath_hash.sh
@@ -181,37 +181,43 @@
 
 send_src_ipv4()
 {
-	$MZ $h1 -q -p 64 -A "198.51.100.2-198.51.100.253" -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A "198.51.100.2-198.51.100.253" -B 203.0.113.2 \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_dst_ipv4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B "203.0.113.2-203.0.113.253" \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B "203.0.113.2-203.0.113.253" \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_src_udp4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B 203.0.113.2 \
 		-d 1msec -t udp "sp=0-32768,dp=30000"
 }
 
 send_dst_udp4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B 203.0.113.2 \
 		-d 1msec -t udp "sp=20000,dp=0-32768"
 }
 
 send_src_ipv6()
 {
-	$MZ -6 $h1 -q -p 64 -A "2001:db8:1::2-2001:db8:1::fd" -B 2001:db8:4::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A "2001:db8:1::2-2001:db8:1::fd" -B 2001:db8:4::2 \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_dst_ipv6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B "2001:db8:4::2-2001:db8:4::fd" \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B "2001:db8:4::2-2001:db8:4::fd" \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
@@ -226,13 +232,15 @@
 
 send_src_udp6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B 2001:db8:4::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B 2001:db8:4::2 \
 		-d 1msec -t udp "sp=0-32768,dp=30000"
 }
 
 send_dst_udp6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B 2001:db8:4::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B 2001:db8:4::2 \
 		-d 1msec -t udp "sp=20000,dp=0-32768"
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/devlink_lib.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/devlink_lib.sh
@@ -122,6 +122,8 @@
 	still_pending=$(devlink resource show "$DEVLINK_DEV" | \
 			grep -c "size_new")
 	check_err $still_pending "Failed reload - There are still unset sizes"
+
+	udevadm settle
 }
 
 declare -A DEVLINK_ORIG
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/ethtool.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/ethtool.sh
@@ -286,6 +286,8 @@
 	ethtool -s $h1 autoneg on
 }
 
+skip_on_veth
+
 trap cleanup EXIT
 
 setup_prepare
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/ethtool_extended_state.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/ethtool_extended_state.sh
@@ -95,6 +95,8 @@
 	ip link set dev $swp3 down
 }
 
+skip_on_veth
+
 setup_prepare
 
 tests_run
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/forwarding.config.sample
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/forwarding.config.sample
@@ -13,6 +13,8 @@
 NETIFS[p6]=veth5
 NETIFS[p7]=veth6
 NETIFS[p8]=veth7
+NETIFS[p9]=veth8
+NETIFS[p10]=veth9
 
 # Port that does not have a cable connected.
 NETIF_NO_CABLE=eth8
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/gre_custom_multipath_hash.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/gre_custom_multipath_hash.sh
@@ -276,37 +276,43 @@
 
 send_src_ipv4()
 {
-	$MZ $h1 -q -p 64 -A "198.51.100.2-198.51.100.253" -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A "198.51.100.2-198.51.100.253" -B 203.0.113.2 \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_dst_ipv4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B "203.0.113.2-203.0.113.253" \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B "203.0.113.2-203.0.113.253" \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_src_udp4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B 203.0.113.2 \
 		-d 1msec -t udp "sp=0-32768,dp=30000"
 }
 
 send_dst_udp4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B 203.0.113.2 \
 		-d 1msec -t udp "sp=20000,dp=0-32768"
 }
 
 send_src_ipv6()
 {
-	$MZ -6 $h1 -q -p 64 -A "2001:db8:1::2-2001:db8:1::fd" -B 2001:db8:2::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A "2001:db8:1::2-2001:db8:1::fd" -B 2001:db8:2::2 \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_dst_ipv6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B "2001:db8:2::2-2001:db8:2::fd" \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B "2001:db8:2::2-2001:db8:2::fd" \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
@@ -321,13 +327,15 @@
 
 send_src_udp6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B 2001:db8:2::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B 2001:db8:2::2 \
 		-d 1msec -t udp "sp=0-32768,dp=30000"
 }
 
 send_dst_udp6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B 2001:db8:2::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B 2001:db8:2::2 \
 		-d 1msec -t udp "sp=20000,dp=0-32768"
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/ip6gre_custom_multipath_hash.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/ip6gre_custom_multipath_hash.sh
@@ -278,37 +278,43 @@
 
 send_src_ipv4()
 {
-	$MZ $h1 -q -p 64 -A "198.51.100.2-198.51.100.253" -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A "198.51.100.2-198.51.100.253" -B 203.0.113.2 \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_dst_ipv4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B "203.0.113.2-203.0.113.253" \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B "203.0.113.2-203.0.113.253" \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_src_udp4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B 203.0.113.2 \
 		-d 1msec -t udp "sp=0-32768,dp=30000"
 }
 
 send_dst_udp4()
 {
-	$MZ $h1 -q -p 64 -A 198.51.100.2 -B 203.0.113.2 \
+	ip vrf exec v$h1 $MZ $h1 -q -p 64 \
+		-A 198.51.100.2 -B 203.0.113.2 \
 		-d 1msec -t udp "sp=20000,dp=0-32768"
 }
 
 send_src_ipv6()
 {
-	$MZ -6 $h1 -q -p 64 -A "2001:db8:1::2-2001:db8:1::fd" -B 2001:db8:2::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A "2001:db8:1::2-2001:db8:1::fd" -B 2001:db8:2::2 \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
 send_dst_ipv6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B "2001:db8:2::2-2001:db8:2::fd" \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B "2001:db8:2::2-2001:db8:2::fd" \
 		-d 1msec -c 50 -t udp "sp=20000,dp=30000"
 }
 
@@ -323,13 +329,15 @@
 
 send_src_udp6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B 2001:db8:2::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B 2001:db8:2::2 \
 		-d 1msec -t udp "sp=0-32768,dp=30000"
 }
 
 send_dst_udp6()
 {
-	$MZ -6 $h1 -q -p 64 -A 2001:db8:1::2 -B 2001:db8:2::2 \
+	ip vrf exec v$h1 $MZ -6 $h1 -q -p 64 \
+		-A 2001:db8:1::2 -B 2001:db8:2::2 \
 		-d 1msec -t udp "sp=20000,dp=0-32768"
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/lib.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/lib.sh
@@ -122,6 +122,17 @@
 	fi
 }
 
+skip_on_veth()
+{
+	local kind=$(ip -j -d link show dev ${NETIFS[p1]} |
+		jq -r '.[].linkinfo.info_kind')
+
+	if [[ $kind == veth ]]; then
+		echo "SKIP: Test cannot be run with veth pairs"
+		exit $ksft_skip
+	fi
+}
+
 if [[ "$(id -u)" -ne 0 ]]; then
 	echo "SKIP: need root privileges"
 	exit $ksft_skip
@@ -174,6 +185,11 @@
 	for ((i = 1; i <= NUM_NETIFS; ++i)); do
 		local j=$((i+1))
 
+		if [ -z ${NETIFS[p$i]} ]; then
+			echo "SKIP: Cannot create interface. Name not specified"
+			exit $ksft_skip
+		fi
+
 		ip link show dev ${NETIFS[p$i]} &> /dev/null
 		if [[ $? -ne 0 ]]; then
 			ip link add ${NETIFS[p$i]} type veth \
@@ -817,14 +833,14 @@
 	local value=$1; shift
 
 	SYSCTL_ORIG[$key]=$(sysctl -n $key)
-	sysctl -qw $key=$value
+	sysctl -qw $key="$value"
 }
 
 sysctl_restore()
 {
 	local key=$1; shift
 
-	sysctl -qw $key=${SYSCTL_ORIG["$key"]}
+	sysctl -qw $key="${SYSCTL_ORIG[$key]}"
 }
 
 forwarding_enable()
@@ -1149,6 +1165,7 @@
 	# FDB entry was installed.
 	bridge link set dev $br_port1 flood off
 
+	ip link set $host1_if promisc on
 	tc qdisc add dev $host1_if ingress
 	tc filter add dev $host1_if ingress protocol ip pref 1 handle 101 \
 		flower dst_mac $mac action drop
@@ -1159,7 +1176,7 @@
 	tc -j -s filter show dev $host1_if ingress \
 		| jq -e ".[] | select(.options.handle == 101) \
 		| select(.options.actions[0].stats.packets == 1)" &> /dev/null
-	check_fail $? "Packet reached second host when should not"
+	check_fail $? "Packet reached first host when should not"
 
 	$MZ $host1_if -c 1 -p 64 -a $mac -t ip -q
 	sleep 1
@@ -1198,6 +1215,7 @@
 
 	tc filter del dev $host1_if ingress protocol ip pref 1 handle 101 flower
 	tc qdisc del dev $host1_if ingress
+	ip link set $host1_if promisc off
 
 	bridge link set dev $br_port1 flood on
 
@@ -1215,6 +1233,7 @@
 
 	# Add an ACL on `host2_if` which will tell us whether the packet
 	# was flooded to it or not.
+	ip link set $host2_if promisc on
 	tc qdisc add dev $host2_if ingress
 	tc filter add dev $host2_if ingress protocol ip pref 1 handle 101 \
 		flower dst_mac $mac action drop
@@ -1232,6 +1251,7 @@
 
 	tc filter del dev $host2_if ingress protocol ip pref 1 handle 101 flower
 	tc qdisc del dev $host2_if ingress
+	ip link set $host2_if promisc off
 
 	return $err
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1d.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1d.sh
@@ -93,12 +93,16 @@
 
 test_gretap()
 {
+	ip neigh replace 192.0.2.130 lladdr $(mac_get $h3) \
+		 nud permanent dev br2
 	full_test_span_gre_dir gt4 ingress 8 0 "mirror to gretap"
 	full_test_span_gre_dir gt4 egress 0 8 "mirror to gretap"
 }
 
 test_ip6gretap()
 {
+	ip neigh replace 2001:db8:2::2 lladdr $(mac_get $h3) \
+		nud permanent dev br2
 	full_test_span_gre_dir gt6 ingress 8 0 "mirror to ip6gretap"
 	full_test_span_gre_dir gt6 egress 0 8 "mirror to ip6gretap"
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1q.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1q.sh
@@ -61,9 +61,12 @@
 
 	vrf_prepare
 	mirror_gre_topo_create
+	# Avoid changing br1's PVID while it is operational as a L3 interface.
+	ip link set dev br1 down
 
 	ip link set dev $swp3 master br1
 	bridge vlan add dev br1 vid 555 pvid untagged self
+	ip link set dev br1 up
 	ip address add dev br1 192.0.2.129/28
 	ip address add dev br1 2001:db8:2::1/64
 
@@ -87,12 +90,16 @@
 
 test_gretap()
 {
+	ip neigh replace 192.0.2.130 lladdr $(mac_get $h3) \
+		 nud permanent dev br1
 	full_test_span_gre_dir gt4 ingress 8 0 "mirror to gretap"
 	full_test_span_gre_dir gt4 egress 0 8 "mirror to gretap"
 }
 
 test_ip6gretap()
 {
+	ip neigh replace 2001:db8:2::2 lladdr $(mac_get $h3) \
+		nud permanent dev br1
 	full_test_span_gre_dir gt6 ingress 8 0 "mirror to ip6gretap"
 	full_test_span_gre_dir gt6 egress 0 8 "mirror to ip6gretap"
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/mirror_gre_changes.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/mirror_gre_changes.sh
@@ -72,7 +72,8 @@
 
 	RET=0
 
-	mirror_install $swp1 ingress $tundev "matchall $tcflags"
+	mirror_install $swp1 ingress $tundev \
+		"prot ip flower $tcflags ip_prot icmp"
 	tc filter add dev $h3 ingress pref 77 prot $prot \
 		flower ip_ttl 50 action pass
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/sch_red.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/sch_red.sh
@@ -1,3 +1,4 @@
+#!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
 # This test sends one stream of traffic from H1 through a TBF shaper, to a RED
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/settings
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/settings
@@ -0,0 +1 @@
+timeout=0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/tc_actions.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/tc_actions.sh
@@ -3,11 +3,13 @@
 
 ALL_TESTS="gact_drop_and_ok_test mirred_egress_redirect_test \
 	mirred_egress_mirror_test matchall_mirred_egress_mirror_test \
-	gact_trap_test"
+	gact_trap_test mirred_egress_to_ingress_tcp_test"
 NUM_NETIFS=4
 source tc_common.sh
 source lib.sh
 
+require_command ncat
+
 tcflags="skip_hw"
 
 h1_create()
@@ -153,6 +155,52 @@
 	log_test "trap ($tcflags)"
 }
 
+mirred_egress_to_ingress_tcp_test()
+{
+	mirred_e2i_tf1=$(mktemp) mirred_e2i_tf2=$(mktemp)
+
+	RET=0
+	dd conv=sparse status=none if=/dev/zero bs=1M count=2 of=$mirred_e2i_tf1
+	tc filter add dev $h1 protocol ip pref 100 handle 100 egress flower \
+		$tcflags ip_proto tcp src_ip 192.0.2.1 dst_ip 192.0.2.2 \
+			action ct commit nat src addr 192.0.2.2 pipe \
+			action ct clear pipe \
+			action ct commit nat dst addr 192.0.2.1 pipe \
+			action ct clear pipe \
+			action skbedit ptype host pipe \
+			action mirred ingress redirect dev $h1
+	tc filter add dev $h1 protocol ip pref 101 handle 101 egress flower \
+		$tcflags ip_proto icmp \
+			action mirred ingress redirect dev $h1
+	tc filter add dev $h1 protocol ip pref 102 handle 102 ingress flower \
+		ip_proto icmp \
+			action drop
+
+	ip vrf exec v$h1 ncat --recv-only -w10 -l -p 12345 -o $mirred_e2i_tf2 &
+	local rpid=$!
+	ip vrf exec v$h1 ncat -w1 --send-only 192.0.2.2 12345 <$mirred_e2i_tf1
+	wait -n $rpid
+	cmp -s $mirred_e2i_tf1 $mirred_e2i_tf2
+	check_err $? "server output check failed"
+
+	$MZ $h1 -c 10 -p 64 -a $h1mac -b $h1mac -A 192.0.2.1 -B 192.0.2.1 \
+		-t icmp "ping,id=42,seq=5" -q
+	tc_check_packets "dev $h1 egress" 101 10
+	check_err $? "didn't mirred redirect ICMP"
+	tc_check_packets "dev $h1 ingress" 102 10
+	check_err $? "didn't drop mirred ICMP"
+	local overlimits=$(tc_rule_stats_get ${h1} 101 egress .overlimits)
+	test ${overlimits} = 10
+	check_err $? "wrong overlimits, expected 10 got ${overlimits}"
+
+	tc filter del dev $h1 egress protocol ip pref 100 handle 100 flower
+	tc filter del dev $h1 egress protocol ip pref 101 handle 101 flower
+	tc filter del dev $h1 ingress protocol ip pref 102 handle 102 flower
+
+	rm -f $mirred_e2i_tf1 $mirred_e2i_tf2
+	log_test "mirred_egress_to_ingress_tcp ($tcflags)"
+}
+
 setup_prepare()
 {
 	h1=${NETIFS[p1]}
@@ -178,6 +226,8 @@
 
 cleanup()
 {
+	local tf
+
 	pre_cleanup
 
 	switch_destroy
@@ -188,6 +238,8 @@
 
 	ip link set $swp2 address $swp2origmac
 	ip link set $swp1 address $swp1origmac
+
+	for tf in $mirred_e2i_tf1 $mirred_e2i_tf2; do rm -f $tf; done
 }
 
 mirred_egress_redirect_test()
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/tc_flower.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/tc_flower.sh
@@ -52,8 +52,8 @@
 	tc_check_packets "dev $h2 ingress" 101 1
 	check_fail $? "Matched on a wrong filter"
 
-	tc_check_packets "dev $h2 ingress" 102 1
-	check_err $? "Did not match on correct filter"
+	tc_check_packets "dev $h2 ingress" 102 0
+	check_fail $? "Did not match on correct filter"
 
 	tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower
 	tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower
@@ -78,8 +78,8 @@
 	tc_check_packets "dev $h2 ingress" 101 1
 	check_fail $? "Matched on a wrong filter"
 
-	tc_check_packets "dev $h2 ingress" 102 1
-	check_err $? "Did not match on correct filter"
+	tc_check_packets "dev $h2 ingress" 102 0
+	check_fail $? "Did not match on correct filter"
 
 	tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower
 	tc filter del dev $h2 ingress protocol ip pref 2 handle 102 flower
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/forwarding/tc_police.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/forwarding/tc_police.sh
@@ -37,6 +37,8 @@
 	police_tx_mirror_test
 	police_pps_rx_test
 	police_pps_tx_test
+	police_mtu_rx_test
+	police_mtu_tx_test
 "
 NUM_NETIFS=6
 source tc_common.sh
@@ -346,6 +348,56 @@
 	tc filter del dev $rp2 egress protocol ip pref 1 handle 101 flower
 }
 
+police_mtu_common_test() {
+	RET=0
+
+	local test_name=$1; shift
+	local dev=$1; shift
+	local direction=$1; shift
+
+	tc filter add dev $dev $direction protocol ip pref 1 handle 101 flower \
+		dst_ip 198.51.100.1 ip_proto udp dst_port 54321 \
+		action police mtu 1042 conform-exceed drop/ok
+
+	# to count "conform" packets
+	tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \
+		dst_ip 198.51.100.1 ip_proto udp dst_port 54321 \
+		action drop
+
+	mausezahn $h1 -a own -b $(mac_get $rp1) -A 192.0.2.1 -B 198.51.100.1 \
+		-t udp sp=12345,dp=54321 -p 1001 -c 10 -q
+
+	mausezahn $h1 -a own -b $(mac_get $rp1) -A 192.0.2.1 -B 198.51.100.1 \
+		-t udp sp=12345,dp=54321 -p 1000 -c 3 -q
+
+	tc_check_packets "dev $dev $direction" 101 13
+	check_err $? "wrong packet counter"
+
+	# "exceed" packets
+	local overlimits_t0=$(tc_rule_stats_get ${dev} 1 ${direction} .overlimits)
+	test ${overlimits_t0} = 10
+	check_err $? "wrong overlimits, expected 10 got ${overlimits_t0}"
+
+	# "conform" packets
+	tc_check_packets "dev $h2 ingress" 101 3
+	check_err $? "forwarding error"
+
+	tc filter del dev $h2 ingress protocol ip pref 1 handle 101 flower
+	tc filter del dev $dev $direction protocol ip pref 1 handle 101 flower
+
+	log_test "$test_name"
+}
+
+police_mtu_rx_test()
+{
+	police_mtu_common_test "police mtu (rx)" $rp1 ingress
+}
+
+police_mtu_tx_test()
+{
+	police_mtu_common_test "police mtu (tx)" $rp2 egress
+}
+
 setup_prepare()
 {
 	h1=${NETIFS[p1]}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/gre_gso.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/gre_gso.sh
@@ -116,17 +116,20 @@
 {
 	local name=$1
 	local addr=$2
+	local proto=$3
 
-	$NS_EXEC nc -kl $port >/dev/null &
+	[ "$proto" == 6 ] && addr="[$addr]"
+
+	$NS_EXEC socat - tcp${proto}-listen:$port,reuseaddr,fork >/dev/null &
 	PID=$!
 	while ! $NS_EXEC ss -ltn | grep -q $port; do ((i++)); sleep 0.01; done
 
-	cat $TMPFILE | timeout 1 nc $addr $port
+	cat $TMPFILE | timeout 1 socat -u STDIN TCP:$addr:$port
 	log_test $? 0 "$name - copy file w/ TSO"
 
 	ethtool -K veth0 tso off
 
-	cat $TMPFILE | timeout 1 nc $addr $port
+	cat $TMPFILE | timeout 1 socat -u STDIN TCP:$addr:$port
 	log_test $? 0 "$name - copy file w/ GSO"
 
 	ethtool -K veth0 tso on
@@ -154,8 +157,8 @@
 
 	sleep 2
 
-	gre_gst_test_checks GREv6/v4 172.16.2.2
-	gre_gst_test_checks GREv6/v6 2001:db8:1::2
+	gre_gst_test_checks GREv6/v4 172.16.2.2 4
+	gre_gst_test_checks GREv6/v6 2001:db8:1::2 6
 
 	cleanup
 }
@@ -211,8 +214,8 @@
 	exit $ksft_skip
 fi
 
-if [ ! -x "$(command -v nc)" ]; then
-	echo "SKIP: Could not run test without nc tool"
+if [ ! -x "$(command -v socat)" ]; then
+	echo "SKIP: Could not run test without socat tool"
 	exit $ksft_skip
 fi
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/icmp_redirect.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/icmp_redirect.sh
@@ -311,7 +311,7 @@
 		ip -netns h1 ro get ${H1_VRF_ARG} ${H2_N2_IP} | \
 		grep -E -v 'mtu|redirected' | grep -q "cache"
 	fi
-	log_test $? 0 "IPv4: ${desc}"
+	log_test $? 0 "IPv4: ${desc}" 0
 
 	# No PMTU info for test "redirect" and "mtu exception plus redirect"
 	if [ "$with_redirect" = "yes" ] && [ "$desc" != "redirect exception plus mtu" ]; then
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/ioam6.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/ioam6.sh
@@ -117,6 +117,8 @@
 #        | Schema Data         |                                     |
 #        +-----------------------------------------------------------+
 
+# Kselftest framework requirement - SKIP code is 4.
+ksft_skip=4
 
 ################################################################################
 #                                                                              #
@@ -211,7 +213,7 @@
     echo "SKIP: kernel version probably too old, missing ioam support"
     ip link del veth0 2>/dev/null || true
     ip netns del ioam-tmp-node || true
-    exit 1
+    exit $ksft_skip
   fi
 
   ip -netns ioam-tmp-node route add db02::/64 encap ioam6 trace prealloc \
@@ -227,7 +229,7 @@
          "without CONFIG_IPV6_IOAM6_LWTUNNEL?"
     ip link del veth0 2>/dev/null || true
     ip netns del ioam-tmp-node || true
-    exit 1
+    exit $ksft_skip
   fi
 
   ip link del veth0 2>/dev/null || true
@@ -644,20 +646,20 @@
 if [ "$(id -u)" -ne 0 ]
 then
   echo "SKIP: Need root privileges"
-  exit 1
+  exit $ksft_skip
 fi
 
 if [ ! -x "$(command -v ip)" ]
 then
   echo "SKIP: Could not run test without ip tool"
-  exit 1
+  exit $ksft_skip
 fi
 
 ip ioam &>/dev/null
 if [ $? = 1 ]
 then
   echo "SKIP: iproute2 too old, missing ioam command"
-  exit 1
+  exit $ksft_skip
 fi
 
 check_kernel_compatibility
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/ipsec.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/ipsec.c
@@ -189,7 +189,8 @@
 
 	attr->rta_len = RTA_LENGTH(size);
 	attr->rta_type = rta_type;
-	memcpy(RTA_DATA(attr), payload, size);
+	if (payload)
+		memcpy(RTA_DATA(attr), payload, size);
 
 	return 0;
 }
@@ -2278,7 +2279,7 @@
 
 int main(int argc, char **argv)
 {
-	unsigned int nr_process = 1;
+	long nr_process = 1;
 	int route_sock = -1, ret = KSFT_SKIP;
 	int test_desc_fd[2];
 	uint32_t route_seq;
@@ -2299,7 +2300,7 @@
 			exit_usage(argv);
 		}
 
-		if (nr_process > MAX_PROCESSES || !nr_process) {
+		if (nr_process > MAX_PROCESSES || nr_process < 1) {
 			printk("nr_process should be between [1; %u]",
 					MAX_PROCESSES);
 			exit_usage(argv);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/Makefile
@@ -10,7 +10,7 @@
 
 TEST_GEN_FILES = mptcp_connect pm_nl_ctl
 
-TEST_FILES := settings
+TEST_FILES := mptcp_lib.sh settings
 
 EXTRA_CLEAN := *.pcap
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/config
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/config
@@ -1,3 +1,4 @@
+CONFIG_KALLSYMS=y
 CONFIG_MPTCP=y
 CONFIG_IPV6=y
 CONFIG_MPTCP_IPV6=y
@@ -5,6 +6,7 @@
 CONFIG_INET_MPTCP_DIAG=m
 CONFIG_VETH=y
 CONFIG_NET_SCH_NETEM=m
+CONFIG_SYN_COOKIES=y
 CONFIG_NETFILTER=y
 CONFIG_NETFILTER_ADVANCED=y
 CONFIG_NETFILTER_NETLINK=m
@@ -15,3 +17,5 @@
 CONFIG_NETFILTER_XT_MATCH_BPF=m
 CONFIG_NF_TABLES_IPV4=y
 CONFIG_NF_TABLES_IPV6=y
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP6_NF_FILTER=m
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/diag.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/diag.sh
@@ -1,6 +1,8 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
+. "$(dirname "${0}")/mptcp_lib.sh"
+
 rndh=$(printf %x $sec)-$(mktemp -u XXXXXX)
 ns="ns1-$rndh"
 ksft_skip=4
@@ -25,6 +27,8 @@
 	ip netns del $ns
 }
 
+mptcp_lib_check_mptcp
+
 ip -Version > /dev/null 2>&1
 if [ $? -ne 0 ];then
 	echo "SKIP: Could not run test without ip tool"
@@ -49,7 +53,7 @@
 	printf "%-50s" "$msg"
 	if [ $nr != $expected ]; then
 		echo "[ fail ] expected $expected found $nr"
-		ret=$test_cnt
+		ret=${KSFT_FAIL}
 	else
 		echo "[  ok  ]"
 	fi
@@ -61,6 +65,39 @@
 	__chk_nr "grep -c token:" $*
 }
 
+wait_msk_nr()
+{
+	local condition="grep -c token:"
+	local expected=$1
+	local timeout=20
+	local msg nr
+	local max=0
+	local i=0
+
+	shift 1
+	msg=$*
+
+	while [ $i -lt $timeout ]; do
+		nr=$(ss -inmHMN $ns | $condition)
+		[ $nr == $expected ] && break;
+		[ $nr -gt $max ] && max=$nr
+		i=$((i + 1))
+		sleep 1
+	done
+
+	printf "%-50s" "$msg"
+	if [ $i -ge $timeout ]; then
+		echo "[ fail ] timeout while expecting $expected max $max last $nr"
+		ret=${KSFT_FAIL}
+	elif [ $nr != $expected ]; then
+		echo "[ fail ] expected $expected found $nr"
+		ret=${KSFT_FAIL}
+	else
+		echo "[  ok  ]"
+	fi
+	test_cnt=$((test_cnt+1))
+}
+
 chk_msk_fallback_nr()
 {
 		__chk_nr "grep -c fallback" $*
@@ -71,6 +108,36 @@
 		__chk_nr "grep -c remote_key" $*
 }
 
+# $1: ns, $2: port
+wait_local_port_listen()
+{
+	local listener_ns="${1}"
+	local port="${2}"
+
+	local port_hex i
+
+	port_hex="$(printf "%04X" "${port}")"
+	for i in $(seq 10); do
+		ip netns exec "${listener_ns}" cat /proc/net/tcp | \
+			awk "BEGIN {rc=1} {if (\$2 ~ /:${port_hex}\$/ && \$4 ~ /0A/) {rc=0; exit}} END {exit rc}" &&
+			break
+		sleep 0.1
+	done
+}
+
+wait_connected()
+{
+	local listener_ns="${1}"
+	local port="${2}"
+
+	local port_hex i
+
+	port_hex="$(printf "%04X" "${port}")"
+	for i in $(seq 10); do
+		ip netns exec ${listener_ns} grep -q " 0100007F:${port_hex} " /proc/net/tcp && break
+		sleep 0.1
+	done
+}
 
 trap cleanup EXIT
 ip netns add $ns
@@ -79,17 +146,17 @@
 echo "a" | \
 	timeout ${timeout_test} \
 		ip netns exec $ns \
-			./mptcp_connect -p 10000 -l -t ${timeout_poll} \
+			./mptcp_connect -p 10000 -l -t ${timeout_poll} -w 20 \
 				0.0.0.0 >/dev/null &
-sleep 0.1
+wait_local_port_listen $ns 10000
 chk_msk_nr 0 "no msk on netns creation"
 
 echo "b" | \
 	timeout ${timeout_test} \
 		ip netns exec $ns \
-			./mptcp_connect -p 10000 -j -t ${timeout_poll} \
+			./mptcp_connect -p 10000 -r 0 -t ${timeout_poll} -w 20 \
 				127.0.0.1 >/dev/null &
-sleep 0.1
+wait_connected $ns 10000
 chk_msk_nr 2 "after MPC handshake "
 chk_msk_remote_key_nr 2 "....chk remote_key"
 chk_msk_fallback_nr 0 "....chk no fallback"
@@ -99,15 +166,15 @@
 echo "a" | \
 	timeout ${timeout_test} \
 		ip netns exec $ns \
-			./mptcp_connect -p 10001 -l -s TCP -t ${timeout_poll} \
+			./mptcp_connect -p 10001 -l -s TCP -t ${timeout_poll} -w 20 \
 				0.0.0.0 >/dev/null &
-sleep 0.1
+wait_local_port_listen $ns 10001
 echo "b" | \
 	timeout ${timeout_test} \
 		ip netns exec $ns \
-			./mptcp_connect -p 10001 -j -t ${timeout_poll} \
+			./mptcp_connect -p 10001 -r 0 -t ${timeout_poll} -w 20 \
 				127.0.0.1 >/dev/null &
-sleep 0.1
+wait_connected $ns 10001
 chk_msk_fallback_nr 1 "check fallback"
 flush_pids
 
@@ -116,21 +183,20 @@
 	echo "a" | \
 		timeout ${timeout_test} \
 			ip netns exec $ns \
-				./mptcp_connect -p $((I+10001)) -l -w 10 \
+				./mptcp_connect -p $((I+10001)) -l -w 20 \
 					-t ${timeout_poll} 0.0.0.0 >/dev/null &
 done
-sleep 0.1
+wait_local_port_listen $ns $((NR_CLIENTS + 10001))
 
 for I in `seq 1 $NR_CLIENTS`; do
 	echo "b" | \
 		timeout ${timeout_test} \
 			ip netns exec $ns \
-				./mptcp_connect -p $((I+10001)) -w 10 \
+				./mptcp_connect -p $((I+10001)) -w 20 \
 					-t ${timeout_poll} 127.0.0.1 >/dev/null &
 done
-sleep 1.5
 
-chk_msk_nr $((NR_CLIENTS*2)) "many msk socket present"
+wait_msk_nr $((NR_CLIENTS*2)) "many msk socket present"
 flush_pids
 
 exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/mptcp_connect.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/mptcp_connect.c
@@ -14,6 +14,7 @@
 #include <strings.h>
 #include <signal.h>
 #include <unistd.h>
+#include <time.h>
 
 #include <sys/poll.h>
 #include <sys/sendfile.h>
@@ -64,6 +65,7 @@
 static int cfg_rcvbuf;
 static bool cfg_join;
 static bool cfg_remove;
+static unsigned int cfg_time;
 static unsigned int cfg_do_w;
 static int cfg_wait;
 static uint32_t cfg_mark;
@@ -78,9 +80,10 @@
 static void die_usage(void)
 {
 	fprintf(stderr, "Usage: mptcp_connect [-6] [-u] [-s MPTCP|TCP] [-p port] [-m mode]"
-		"[-l] [-w sec] connect_address\n");
+		"[-l] [-w sec] [-t num] [-T num] connect_address\n");
 	fprintf(stderr, "\t-6 use ipv6\n");
 	fprintf(stderr, "\t-t num -- set poll timeout to num\n");
+	fprintf(stderr, "\t-T num -- set expected runtime to num ms\n");
 	fprintf(stderr, "\t-S num -- set SO_SNDBUF to num\n");
 	fprintf(stderr, "\t-R num -- set SO_RCVBUF to num\n");
 	fprintf(stderr, "\t-p num -- use port num\n");
@@ -448,7 +451,7 @@
 	fcntl(fd, F_SETFL, flags | O_NONBLOCK);
 }
 
-static int copyfd_io_poll(int infd, int peerfd, int outfd)
+static int copyfd_io_poll(int infd, int peerfd, int outfd, bool *in_closed_after_out)
 {
 	struct pollfd fds = {
 		.fd = peerfd,
@@ -487,9 +490,11 @@
 				 */
 				fds.events &= ~POLLIN;
 
-				if ((fds.events & POLLOUT) == 0)
+				if ((fds.events & POLLOUT) == 0) {
+					*in_closed_after_out = true;
 					/* and nothing more to send */
 					break;
+				}
 
 			/* Else, still have data to transmit */
 			} else if (len < 0) {
@@ -547,7 +552,7 @@
 	}
 
 	/* leave some time for late join/announce */
-	if (cfg_join || cfg_remove)
+	if (cfg_remove)
 		usleep(cfg_wait);
 
 	close(peerfd);
@@ -646,7 +651,7 @@
 }
 
 static int copyfd_io_mmap(int infd, int peerfd, int outfd,
-			  unsigned int size)
+			  unsigned int size, bool *in_closed_after_out)
 {
 	int err;
 
@@ -664,13 +669,14 @@
 		shutdown(peerfd, SHUT_WR);
 
 		err = do_recvfile(peerfd, outfd);
+		*in_closed_after_out = true;
 	}
 
 	return err;
 }
 
 static int copyfd_io_sendfile(int infd, int peerfd, int outfd,
-			      unsigned int size)
+			      unsigned int size, bool *in_closed_after_out)
 {
 	int err;
 
@@ -685,6 +691,7 @@
 		if (err)
 			return err;
 		err = do_recvfile(peerfd, outfd);
+		*in_closed_after_out = true;
 	}
 
 	return err;
@@ -692,27 +699,62 @@
 
 static int copyfd_io(int infd, int peerfd, int outfd)
 {
+	bool in_closed_after_out = false;
+	struct timespec start, end;
 	int file_size;
+	int ret;
+
+	if (cfg_time && (clock_gettime(CLOCK_MONOTONIC, &start) < 0))
+		xerror("can not fetch start time %d", errno);
 
 	switch (cfg_mode) {
 	case CFG_MODE_POLL:
-		return copyfd_io_poll(infd, peerfd, outfd);
+		ret = copyfd_io_poll(infd, peerfd, outfd, &in_closed_after_out);
+		break;
+
 	case CFG_MODE_MMAP:
 		file_size = get_infd_size(infd);
 		if (file_size < 0)
 			return file_size;
-		return copyfd_io_mmap(infd, peerfd, outfd, file_size);
+		ret = copyfd_io_mmap(infd, peerfd, outfd, file_size, &in_closed_after_out);
+		break;
+
 	case CFG_MODE_SENDFILE:
 		file_size = get_infd_size(infd);
 		if (file_size < 0)
 			return file_size;
-		return copyfd_io_sendfile(infd, peerfd, outfd, file_size);
+		ret = copyfd_io_sendfile(infd, peerfd, outfd, file_size, &in_closed_after_out);
+		break;
+
+	default:
+		fprintf(stderr, "Invalid mode %d\n", cfg_mode);
+
+		die_usage();
+		return 1;
 	}
 
-	fprintf(stderr, "Invalid mode %d\n", cfg_mode);
+	if (ret)
+		return ret;
 
-	die_usage();
-	return 1;
+	if (cfg_time) {
+		unsigned int delta_ms;
+
+		if (clock_gettime(CLOCK_MONOTONIC, &end) < 0)
+			xerror("can not fetch end time %d", errno);
+		delta_ms = (end.tv_sec - start.tv_sec) * 1000 + (end.tv_nsec - start.tv_nsec) / 1000000;
+		if (delta_ms > cfg_time) {
+			xerror("transfer slower than expected! runtime %d ms, expected %d ms",
+			       delta_ms, cfg_time);
+		}
+
+		/* show the runtime only if this end shutdown(wr) before receiving the EOF,
+		 * (that is, if this end got the longer runtime)
+		 */
+		if (in_closed_after_out)
+			fprintf(stderr, "%d", delta_ms);
+	}
+
+	return 0;
 }
 
 static void check_sockaddr(int pf, struct sockaddr_storage *ss,
@@ -1005,12 +1047,11 @@
 {
 	int c;
 
-	while ((c = getopt(argc, argv, "6jr:lp:s:hut:m:S:R:w:M:P:c:")) != -1) {
+	while ((c = getopt(argc, argv, "6jr:lp:s:hut:T:m:S:R:w:M:P:c:")) != -1) {
 		switch (c) {
 		case 'j':
 			cfg_join = true;
 			cfg_mode = CFG_MODE_POLL;
-			cfg_wait = 400000;
 			break;
 		case 'r':
 			cfg_remove = true;
@@ -1043,6 +1084,9 @@
 			if (poll_timeout <= 0)
 				poll_timeout = -1;
 			break;
+		case 'T':
+			cfg_time = atoi(optarg);
+			break;
 		case 'm':
 			cfg_mode = parse_mode(optarg);
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/mptcp_connect.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/mptcp_connect.sh
@@ -1,6 +1,8 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
+. "$(dirname "${0}")/mptcp_lib.sh"
+
 time_start=$(date +%s)
 
 optstring="S:R:d:e:l:r:h4cm:f:tC"
@@ -138,6 +140,8 @@
 	done
 }
 
+mptcp_lib_check_mptcp
+
 ip -Version > /dev/null 2>&1
 if [ $? -ne 0 ];then
 	echo "SKIP: Could not run test without ip tool"
@@ -445,6 +449,9 @@
 	local stat_ackrx_last_l=$(get_mib_counter "${listener_ns}" "MPTcpExtMPCapableACKRX")
 	local stat_cookietx_last=$(get_mib_counter "${listener_ns}" "TcpExtSyncookiesSent")
 	local stat_cookierx_last=$(get_mib_counter "${listener_ns}" "TcpExtSyncookiesRecv")
+	local stat_csum_err_s=$(get_mib_counter "${listener_ns}" "MPTcpExtDataCsumErr")
+	local stat_csum_err_c=$(get_mib_counter "${connector_ns}" "MPTcpExtDataCsumErr")
+	local stat_tcpfb_last_l=$(get_mib_counter "${listener_ns}" "MPTcpExtMPCapableFallbackACK")
 
 	timeout ${timeout_test} \
 		ip netns exec ${listener_ns} \
@@ -510,6 +517,7 @@
 	local stat_cookietx_now=$(get_mib_counter "${listener_ns}" "TcpExtSyncookiesSent")
 	local stat_cookierx_now=$(get_mib_counter "${listener_ns}" "TcpExtSyncookiesRecv")
 	local stat_ooo_now=$(get_mib_counter "${listener_ns}" "TcpExtTCPOFOQueue")
+	local stat_tcpfb_now_l=$(get_mib_counter "${listener_ns}" "MPTcpExtMPCapableFallbackACK")
 
 	expect_synrx=$((stat_synrx_last_l))
 	expect_ackrx=$((stat_ackrx_last_l))
@@ -537,6 +545,28 @@
 		fi
 	fi
 
+	if $checksum; then
+		local csum_err_s=$(get_mib_counter "${listener_ns}" "MPTcpExtDataCsumErr")
+		local csum_err_c=$(get_mib_counter "${connector_ns}" "MPTcpExtDataCsumErr")
+
+		local csum_err_s_nr=$((csum_err_s - stat_csum_err_s))
+		if [ $csum_err_s_nr -gt 0 ]; then
+			printf "[ FAIL ]\nserver got $csum_err_s_nr data checksum error[s]"
+			rets=1
+		fi
+
+		local csum_err_c_nr=$((csum_err_c - stat_csum_err_c))
+		if [ $csum_err_c_nr -gt 0 ]; then
+			printf "[ FAIL ]\nclient got $csum_err_c_nr data checksum error[s]"
+			retc=1
+		fi
+	fi
+
+	if [ ${stat_ooo_now} -eq 0 ] && [ ${stat_tcpfb_last_l} -ne ${stat_tcpfb_now_l} ]; then
+		printf "[ FAIL ]\nunexpected fallback to TCP"
+		rets=1
+	fi
+
 	if [ $retc -eq 0 ] && [ $rets -eq 0 ]; then
 		printf "[ OK ]"
 	fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/mptcp_join.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/mptcp_join.sh
@@ -1,6 +1,8 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
+. "$(dirname "${0}")/mptcp_lib.sh"
+
 ret=0
 sin=""
 sinfail=""
@@ -10,6 +12,8 @@
 cinsent=""
 cout=""
 ksft_skip=4
+iptables="iptables"
+ip6tables="ip6tables"
 timeout_poll=30
 timeout_test=$((timeout_poll * 2 + 1))
 mptcp_connect=""
@@ -75,6 +79,7 @@
 
 		# let $ns2 reach any $ns1 address from any interface
 		ip -net "$ns2" route add default via 10.0.$i.1 dev ns2eth$i metric 10$i
+		ip -net "$ns2" route add default via dead:beef:$i::1 dev ns2eth$i metric 10$i
 	done
 }
 
@@ -123,9 +128,9 @@
 	local ip="${1:-4}"
 	local tables
 
-	tables="iptables"
+	tables="${iptables}"
 	if [ $ip -eq 6 ]; then
-		tables="ip6tables"
+		tables="${ip6tables}"
 	fi
 
 	reset
@@ -160,20 +165,21 @@
 	ip netns exec $ns2 sysctl -q net.mptcp.allow_join_initial_addr_port=$ns2_enable
 }
 
+mptcp_lib_check_mptcp
+
 ip -Version > /dev/null 2>&1
 if [ $? -ne 0 ];then
 	echo "SKIP: Could not run test without ip tool"
 	exit $ksft_skip
 fi
 
-iptables -V > /dev/null 2>&1
-if [ $? -ne 0 ];then
+if iptables-legacy -V &> /dev/null; then
+	iptables="iptables-legacy"
+	ip6tables="ip6tables-legacy"
+elif ! iptables -V &> /dev/null; then
 	echo "SKIP: Could not run all tests without iptables tool"
 	exit $ksft_skip
-fi
-
-ip6tables -V > /dev/null 2>&1
-if [ $? -ne 0 ];then
+elif ! ip6tables -V &> /dev/null; then
 	echo "SKIP: Could not run all tests without ip6tables tool"
 	exit $ksft_skip
 fi
@@ -238,6 +244,22 @@
 	[ -z "${1##*:*}" ]
 }
 
+# $1: ns ; $2: counter
+get_counter()
+{
+	local ns="${1}"
+	local counter="${2}"
+	local count
+
+	count=$(ip netns exec ${ns} nstat -asz "${counter}" | awk 'NR==1 {next} {print $2}')
+	if [ -z "${count}" ]; then
+		mptcp_lib_fail_if_expected_feature "${counter} counter"
+		return 1
+	fi
+
+	echo "${count}"
+}
+
 do_transfer()
 {
 	listener_ns="$1"
@@ -297,7 +319,7 @@
 	if [ "$test_link_fail" -eq 2 ];then
 		timeout ${timeout_test} \
 			ip netns exec ${listener_ns} \
-				$mptcp_connect -t ${timeout_poll} -l -p $port -s ${cl_proto} \
+				$mptcp_connect -t ${timeout_poll} -l -p $port -s ${srv_proto} \
 					${local_addr} < "$sinfail" > "$sout" &
 	else
 		timeout ${timeout_test} \
@@ -551,9 +573,10 @@
 		echo -n "  "
 	fi
 	printf " %-36s %s" "$msg" "sum"
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtDataCsumErr | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != 0 ]; then
+	count=$(get_counter ${ns1} "MPTcpExtDataCsumErr")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != 0 ]; then
 		echo "[fail] got $count data checksum error[s] expected 0"
 		ret=1
 		dump_stats=1
@@ -561,9 +584,10 @@
 		echo -n "[ ok ]"
 	fi
 	echo -n " - csum  "
-	count=`ip netns exec $ns2 nstat -as | grep MPTcpExtDataCsumErr | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != 0 ]; then
+	count=$(get_counter ${ns2} "MPTcpExtDataCsumErr")
+	if [ -z "$count" ]; then
+		echo "[skip]"
+	elif [ "$count" != 0 ]; then
 		echo "[fail] got $count data checksum error[s] expected 0"
 		ret=1
 		dump_stats=1
@@ -586,9 +610,10 @@
 	local dump_stats
 
 	printf "%-39s %s" " " "ftx"
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPFailTx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$mp_fail_nr_tx" ]; then
+	count=$(get_counter ${ns1} "MPTcpExtMPFailTx")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$mp_fail_nr_tx" ]; then
 		echo "[fail] got $count MP_FAIL[s] TX expected $mp_fail_nr_tx"
 		ret=1
 		dump_stats=1
@@ -597,9 +622,10 @@
 	fi
 
 	echo -n " - frx   "
-	count=`ip netns exec $ns2 nstat -as | grep MPTcpExtMPFailRx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$mp_fail_nr_rx" ]; then
+	count=$(get_counter ${ns2} "MPTcpExtMPFailRx")
+	if [ -z "$count" ]; then
+		echo "[skip]"
+	elif [ "$count" != "$mp_fail_nr_rx" ]; then
 		echo "[fail] got $count MP_FAIL[s] RX expected $mp_fail_nr_rx"
 		ret=1
 		dump_stats=1
@@ -623,11 +649,13 @@
 	local ack_nr=$4
 	local count
 	local dump_stats
+	local with_cookie
 
 	printf "%02u %-36s %s" "$TEST_COUNT" "$msg" "syn"
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPJoinSynRx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$syn_nr" ]; then
+	count=$(get_counter ${ns1} "MPTcpExtMPJoinSynRx")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$syn_nr" ]; then
 		echo "[fail] got $count JOIN[s] syn expected $syn_nr"
 		ret=1
 		dump_stats=1
@@ -636,20 +664,30 @@
 	fi
 
 	echo -n " - synack"
-	count=`ip netns exec $ns2 nstat -as | grep MPTcpExtMPJoinSynAckRx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$syn_ack_nr" ]; then
-		echo "[fail] got $count JOIN[s] synack expected $syn_ack_nr"
-		ret=1
-		dump_stats=1
+	with_cookie=`ip netns exec $ns2 sysctl -n net.ipv4.tcp_syncookies`
+	count=$(get_counter ${ns2} "MPTcpExtMPJoinSynAckRx")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$syn_ack_nr" ]; then
+		# simult connections exceeding the limit with cookie enabled could go up to
+		# synack validation as the conn limit can be enforced reliably only after
+		# the subflow creation
+		if [ "$with_cookie" = 2 ] && [ "$count" -gt "$syn_ack_nr" ] && [ "$count" -le "$syn_nr" ]; then
+			echo -n "[ ok ]"
+		else
+			echo "[fail] got $count JOIN[s] synack expected $syn_ack_nr"
+			ret=1
+			dump_stats=1
+		fi
 	else
 		echo -n "[ ok ]"
 	fi
 
 	echo -n " - ack"
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPJoinAckRx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$ack_nr" ]; then
+	count=$(get_counter ${ns1} "MPTcpExtMPJoinAckRx")
+	if [ -z "$count" ]; then
+		echo "[skip]"
+	elif [ "$count" != "$ack_nr" ]; then
 		echo "[fail] got $count JOIN[s] ack expected $ack_nr"
 		ret=1
 		dump_stats=1
@@ -684,14 +722,13 @@
 	local recover_nr
 
 	printf "%-39s %-18s" " " "stale"
-	stale_nr=`ip netns exec $ns nstat -as | grep MPTcpExtSubflowStale | awk '{print $2}'`
-	[ -z "$stale_nr" ] && stale_nr=0
-	recover_nr=`ip netns exec $ns nstat -as | grep MPTcpExtSubflowRecover | awk '{print $2}'`
-	[ -z "$recover_nr" ] && recover_nr=0
-
-	if [ $stale_nr -lt $stale_min ] ||
-	   [ $stale_max -gt 0 -a $stale_nr -gt $stale_max ] ||
-	   [ $((stale_nr - $recover_nr)) -ne $stale_delta ]; then
+	stale_nr=$(get_counter ${ns} "MPTcpExtSubflowStale")
+	recover_nr=$(get_counter ${ns} "MPTcpExtSubflowRecover")
+	if [ -z "$stale_nr" ] || [ -z "$recover_nr" ]; then
+		echo "[skip]"
+	elif [ $stale_nr -lt $stale_min ] ||
+	     [ $stale_max -gt 0 -a $stale_nr -gt $stale_max ] ||
+	     [ $((stale_nr - $recover_nr)) -ne $stale_delta ]; then
 		echo "[fail] got $stale_nr stale[s] $recover_nr recover[s], " \
 		     " expected stale in range [$stale_min..$stale_max]," \
 		     " stale-recover delta $stale_delta "
@@ -722,9 +759,10 @@
 	local dump_stats
 
 	printf "%-39s %s" " " "add"
-	count=`ip netns exec $ns2 nstat -as | grep MPTcpExtAddAddr | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$add_nr" ]; then
+	count=$(get_counter ${ns2} "MPTcpExtAddAddr")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$add_nr" ]; then
 		echo "[fail] got $count ADD_ADDR[s] expected $add_nr"
 		ret=1
 		dump_stats=1
@@ -733,9 +771,10 @@
 	fi
 
 	echo -n " - echo  "
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtEchoAdd | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$echo_nr" ]; then
+	count=$(get_counter ${ns1} "MPTcpExtEchoAdd")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$echo_nr" ]; then
 		echo "[fail] got $count ADD_ADDR echo[s] expected $echo_nr"
 		ret=1
 		dump_stats=1
@@ -745,9 +784,10 @@
 
 	if [ $port_nr -gt 0 ]; then
 		echo -n " - pt "
-		count=`ip netns exec $ns2 nstat -as | grep MPTcpExtPortAdd | awk '{print $2}'`
-		[ -z "$count" ] && count=0
-		if [ "$count" != "$port_nr" ]; then
+		count=$(get_counter ${ns2} "MPTcpExtPortAdd")
+		if [ -z "$count" ]; then
+			echo "[skip]"
+		elif [ "$count" != "$port_nr" ]; then
 			echo "[fail] got $count ADD_ADDR[s] with a port-number expected $port_nr"
 			ret=1
 			dump_stats=1
@@ -756,10 +796,10 @@
 		fi
 
 		printf "%-39s %s" " " "syn"
-		count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPJoinPortSynRx |
-			awk '{print $2}'`
-		[ -z "$count" ] && count=0
-		if [ "$count" != "$syn_nr" ]; then
+		count=$(get_counter ${ns1} "MPTcpExtMPJoinPortSynRx")
+		if [ -z "$count" ]; then
+			echo -n "[skip]"
+		elif [ "$count" != "$syn_nr" ]; then
 			echo "[fail] got $count JOIN[s] syn with a different \
 				port-number expected $syn_nr"
 			ret=1
@@ -769,10 +809,10 @@
 		fi
 
 		echo -n " - synack"
-		count=`ip netns exec $ns2 nstat -as | grep MPTcpExtMPJoinPortSynAckRx |
-			awk '{print $2}'`
-		[ -z "$count" ] && count=0
-		if [ "$count" != "$syn_ack_nr" ]; then
+		count=$(get_counter ${ns2} "MPTcpExtMPJoinPortSynAckRx")
+		if [ -z "$count" ]; then
+			echo -n "[skip]"
+		elif [ "$count" != "$syn_ack_nr" ]; then
 			echo "[fail] got $count JOIN[s] synack with a different \
 				port-number expected $syn_ack_nr"
 			ret=1
@@ -782,10 +822,10 @@
 		fi
 
 		echo -n " - ack"
-		count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPJoinPortAckRx |
-			awk '{print $2}'`
-		[ -z "$count" ] && count=0
-		if [ "$count" != "$ack_nr" ]; then
+		count=$(get_counter ${ns1} "MPTcpExtMPJoinPortAckRx")
+		if [ -z "$count" ]; then
+			echo "[skip]"
+		elif [ "$count" != "$ack_nr" ]; then
 			echo "[fail] got $count JOIN[s] ack with a different \
 				port-number expected $ack_nr"
 			ret=1
@@ -795,10 +835,10 @@
 		fi
 
 		printf "%-39s %s" " " "syn"
-		count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMismatchPortSynRx |
-			awk '{print $2}'`
-		[ -z "$count" ] && count=0
-		if [ "$count" != "$mis_syn_nr" ]; then
+		count=$(get_counter ${ns1} "MPTcpExtMismatchPortSynRx")
+		if [ -z "$count" ]; then
+			echo -n "[skip]"
+		elif [ "$count" != "$mis_syn_nr" ]; then
 			echo "[fail] got $count JOIN[s] syn with a mismatched \
 				port-number expected $mis_syn_nr"
 			ret=1
@@ -808,10 +848,10 @@
 		fi
 
 		echo -n " - ack   "
-		count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMismatchPortAckRx |
-			awk '{print $2}'`
-		[ -z "$count" ] && count=0
-		if [ "$count" != "$mis_ack_nr" ]; then
+		count=$(get_counter ${ns1} "MPTcpExtMismatchPortAckRx")
+		if [ -z "$count" ]; then
+			echo "[skip]"
+		elif [ "$count" != "$mis_ack_nr" ]; then
 			echo "[fail] got $count JOIN[s] ack with a mismatched \
 				port-number expected $mis_ack_nr"
 			ret=1
@@ -850,9 +890,10 @@
 	fi
 
 	printf "%-39s %s" " " "rm "
-	count=`ip netns exec $addr_ns nstat -as | grep MPTcpExtRmAddr | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$rm_addr_nr" ]; then
+	count=$(get_counter ${addr_ns} "MPTcpExtRmAddr")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$rm_addr_nr" ]; then
 		echo "[fail] got $count RM_ADDR[s] expected $rm_addr_nr"
 		ret=1
 		dump_stats=1
@@ -861,9 +902,10 @@
 	fi
 
 	echo -n " - sf    "
-	count=`ip netns exec $subflow_ns nstat -as | grep MPTcpExtRmSubflow | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$rm_subflow_nr" ]; then
+	count=$(get_counter ${subflow_ns} "MPTcpExtRmSubflow")
+	if [ -z "$count" ]; then
+		echo "[skip]"
+	elif [ "$count" != "$rm_subflow_nr" ]; then
 		echo "[fail] got $count RM_SUBFLOW[s] expected $rm_subflow_nr"
 		ret=1
 		dump_stats=1
@@ -883,13 +925,16 @@
 {
 	local mp_prio_nr_tx=$1
 	local mp_prio_nr_rx=$2
+	local mpj_syn=$3
+	local mpj_syn_ack=$4
 	local count
 	local dump_stats
 
 	printf "%-39s %s" " " "ptx"
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPPrioTx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$mp_prio_nr_tx" ]; then
+	count=$(get_counter ${ns1} "MPTcpExtMPPrioTx")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$mp_prio_nr_tx" ]; then
 		echo "[fail] got $count MP_PRIO[s] TX expected $mp_prio_nr_tx"
 		ret=1
 		dump_stats=1
@@ -898,9 +943,10 @@
 	fi
 
 	echo -n " - prx   "
-	count=`ip netns exec $ns1 nstat -as | grep MPTcpExtMPPrioRx | awk '{print $2}'`
-	[ -z "$count" ] && count=0
-	if [ "$count" != "$mp_prio_nr_rx" ]; then
+	count=$(get_counter ${ns1} "MPTcpExtMPPrioRx")
+	if [ -z "$count" ]; then
+		echo "[skip]"
+	elif [ "$count" != "$mp_prio_nr_rx" ]; then
 		echo "[fail] got $count MP_PRIO[s] RX expected $mp_prio_nr_rx"
 		ret=1
 		dump_stats=1
@@ -908,6 +954,30 @@
 		echo "[ ok ]"
 	fi
 
+	printf "%-39s %s" " " "bkp syn"
+	count=$(get_counter ${ns1} "MPTcpExtMPJoinSynBackupRx")
+	if [ -z "$count" ]; then
+		echo -n "[skip]"
+	elif [ "$count" != "$mpj_syn" ]; then
+		echo "[fail] got $count JOIN[s] syn with Backup expected $mpj_syn"
+		ret=1
+		dump_stats=1
+	else
+		echo -n "[ ok ]"
+	fi
+
+	echo -n " - synack   "
+	count=$(get_counter ${ns2} "MPTcpExtMPJoinSynAckBackupRx")
+	if [ -z "$count" ]; then
+		echo "[skip]"
+	elif [ "$count" != "$mpj_syn_ack" ]; then
+		echo "[fail] got $count JOIN[s] synack with Backup expected $mpj_syn_ack"
+		ret=1
+		dump_stats=1
+	else
+		echo "[ ok ]"
+	fi
+
 	if [ "${dump_stats}" = 1 ]; then
 		echo Server ns stats
 		ip netns exec $ns1 nstat -as | grep MPTcp
@@ -1262,9 +1332,10 @@
 	reset
 	ip netns exec $ns1 ./pm_nl_ctl limits 3 3
 	ip netns exec $ns1 ./pm_nl_ctl add 10.0.12.1 flags signal
+	# broadcast IP: no packet for this address will be received on ns1
+	ip netns exec $ns1 ./pm_nl_ctl add 224.0.0.1 flags signal
 	ip netns exec $ns1 ./pm_nl_ctl add 10.0.3.1 flags signal
-	ip netns exec $ns1 ./pm_nl_ctl add 10.0.14.1 flags signal
-	ip netns exec $ns2 ./pm_nl_ctl limits 3 3
+	ip netns exec $ns2 ./pm_nl_ctl limits 2 2
 	run_tests $ns1 $ns2 10.0.1.1 0 -3 0 slow
 	chk_join_nr "remove invalid addresses" 1 1 1
 	chk_add_nr 3 3
@@ -1383,7 +1454,7 @@
 	reset
 	ip netns exec $ns1 ./pm_nl_ctl limits 0 1
 	ip netns exec $ns2 ./pm_nl_ctl limits 0 1
-	ip netns exec $ns2 ./pm_nl_ctl add dead:beef:3::2 flags subflow
+	ip netns exec $ns2 ./pm_nl_ctl add dead:beef:3::2 dev ns2eth3 flags subflow
 	run_tests $ns1 $ns2 dead:beef:1::1 0 0 0 slow
 	chk_join_nr "single subflow IPv6" 1 1 1
 
@@ -1418,7 +1489,7 @@
 	ip netns exec $ns1 ./pm_nl_ctl limits 0 2
 	ip netns exec $ns1 ./pm_nl_ctl add dead:beef:2::1 flags signal
 	ip netns exec $ns2 ./pm_nl_ctl limits 1 2
-	ip netns exec $ns2 ./pm_nl_ctl add dead:beef:3::2 flags subflow
+	ip netns exec $ns2 ./pm_nl_ctl add dead:beef:3::2 dev ns2eth3 flags subflow
 	run_tests $ns1 $ns2 dead:beef:1::1 0 -1 -1 slow
 	chk_join_nr "remove subflow and signal IPv6" 2 2 2
 	chk_add_nr 1 1
@@ -1512,17 +1583,26 @@
 	ip netns exec $ns2 ./pm_nl_ctl add 10.0.3.2 flags subflow,backup
 	run_tests $ns1 $ns2 10.0.1.1 0 0 0 slow nobackup
 	chk_join_nr "single subflow, backup" 1 1 1
-	chk_prio_nr 0 1
+	chk_prio_nr 0 1 1 0
 
 	# single address, backup
 	reset
 	ip netns exec $ns1 ./pm_nl_ctl limits 0 1
+	ip netns exec $ns1 ./pm_nl_ctl add 10.0.2.1 flags signal,backup
+	ip netns exec $ns2 ./pm_nl_ctl limits 1 1
+	run_tests $ns1 $ns2 10.0.1.1 0 0 0 slow nobackup
+	chk_join_nr "single address, backup" 1 1 1
+	chk_add_nr 1 1
+	chk_prio_nr 1 0 0 1
+
+	reset
+	ip netns exec $ns1 ./pm_nl_ctl limits 0 1
 	ip netns exec $ns1 ./pm_nl_ctl add 10.0.2.1 flags signal
 	ip netns exec $ns2 ./pm_nl_ctl limits 1 1
 	run_tests $ns1 $ns2 10.0.1.1 0 0 0 slow backup
-	chk_join_nr "single address, backup" 1 1 1
+	chk_join_nr "single address, switch to backup" 1 1 1
 	chk_add_nr 1 1
-	chk_prio_nr 1 0
+	chk_prio_nr 1 0 0 0
 }
 
 add_addr_ports_tests()
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/mptcp_lib.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/mptcp_lib.sh
@@ -0,0 +1,104 @@
+#! /bin/bash
+# SPDX-License-Identifier: GPL-2.0
+
+readonly KSFT_FAIL=1
+readonly KSFT_SKIP=4
+
+# SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var can be set when validating all
+# features using the last version of the kernel and the selftests to make sure
+# a test is not being skipped by mistake.
+mptcp_lib_expect_all_features() {
+	[ "${SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES:-}" = "1" ]
+}
+
+# $1: msg
+mptcp_lib_fail_if_expected_feature() {
+	if mptcp_lib_expect_all_features; then
+		echo "ERROR: missing feature: ${*}"
+		exit ${KSFT_FAIL}
+	fi
+
+	return 1
+}
+
+# $1: file
+mptcp_lib_has_file() {
+	local f="${1}"
+
+	if [ -f "${f}" ]; then
+		return 0
+	fi
+
+	mptcp_lib_fail_if_expected_feature "${f} file not found"
+}
+
+mptcp_lib_check_mptcp() {
+	if ! mptcp_lib_has_file "/proc/sys/net/mptcp/enabled"; then
+		echo "SKIP: MPTCP support is not available"
+		exit ${KSFT_SKIP}
+	fi
+}
+
+mptcp_lib_check_kallsyms() {
+	if ! mptcp_lib_has_file "/proc/kallsyms"; then
+		echo "SKIP: CONFIG_KALLSYMS is missing"
+		exit ${KSFT_SKIP}
+	fi
+}
+
+# Internal: use mptcp_lib_kallsyms_has() instead
+__mptcp_lib_kallsyms_has() {
+	local sym="${1}"
+
+	mptcp_lib_check_kallsyms
+
+	grep -q " ${sym}" /proc/kallsyms
+}
+
+# $1: part of a symbol to look at, add '$' at the end for full name
+mptcp_lib_kallsyms_has() {
+	local sym="${1}"
+
+	if __mptcp_lib_kallsyms_has "${sym}"; then
+		return 0
+	fi
+
+	mptcp_lib_fail_if_expected_feature "${sym} symbol not found"
+}
+
+# $1: part of a symbol to look at, add '$' at the end for full name
+mptcp_lib_kallsyms_doesnt_have() {
+	local sym="${1}"
+
+	if ! __mptcp_lib_kallsyms_has "${sym}"; then
+		return 0
+	fi
+
+	mptcp_lib_fail_if_expected_feature "${sym} symbol has been found"
+}
+
+# !!!AVOID USING THIS!!!
+# Features might not land in the expected version and features can be backported
+#
+# $1: kernel version, e.g. 6.3
+mptcp_lib_kversion_ge() {
+	local exp_maj="${1%.*}"
+	local exp_min="${1#*.}"
+	local v maj min
+
+	# If the kernel has backported features, set this env var to 1:
+	if [ "${SELFTESTS_MPTCP_LIB_NO_KVERSION_CHECK:-}" = "1" ]; then
+		return 0
+	fi
+
+	v=$(uname -r | cut -d'.' -f1,2)
+	maj=${v%.*}
+	min=${v#*.}
+
+	if   [ "${maj}" -gt "${exp_maj}" ] ||
+	   { [ "${maj}" -eq "${exp_maj}" ] && [ "${min}" -ge "${exp_min}" ]; }; then
+		return 0
+	fi
+
+	mptcp_lib_fail_if_expected_feature "kernel version ${1} lower than ${v}"
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/mptcp_sockopt.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/mptcp_sockopt.sh
@@ -1,6 +1,8 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
+. "$(dirname "${0}")/mptcp_lib.sh"
+
 ret=0
 sin=""
 sout=""
@@ -11,13 +13,15 @@
 timeout_test=$((timeout_poll * 2 + 1))
 mptcp_connect=""
 do_all_tests=1
+iptables="iptables"
+ip6tables="ip6tables"
 
 add_mark_rules()
 {
 	local ns=$1
 	local m=$2
 
-	for t in iptables ip6tables; do
+	for t in ${iptables} ${ip6tables}; do
 		# just to debug: check we have multiple subflows connection requests
 		ip netns exec $ns $t -A OUTPUT -p tcp --syn -m mark --mark $m -j ACCEPT
 
@@ -80,20 +84,22 @@
 	rm -f "$sin" "$sout"
 }
 
+mptcp_lib_check_mptcp
+
 ip -Version > /dev/null 2>&1
 if [ $? -ne 0 ];then
 	echo "SKIP: Could not run test without ip tool"
 	exit $ksft_skip
 fi
 
-iptables -V > /dev/null 2>&1
-if [ $? -ne 0 ];then
+# Use the legacy version if available to support old kernel versions
+if iptables-legacy -V &> /dev/null; then
+	iptables="iptables-legacy"
+	ip6tables="ip6tables-legacy"
+elif ! iptables -V &> /dev/null; then
 	echo "SKIP: Could not run all tests without iptables tool"
 	exit $ksft_skip
-fi
-
-ip6tables -V > /dev/null 2>&1
-if [ $? -ne 0 ];then
+elif ! ip6tables -V &> /dev/null; then
 	echo "SKIP: Could not run all tests without ip6tables tool"
 	exit $ksft_skip
 fi
@@ -103,10 +109,10 @@
 	local ns=$1
 	local af=$2
 
-	tables=iptables
+	tables=${iptables}
 
 	if [ $af -eq 6 ];then
-		tables=ip6tables
+		tables=${ip6tables}
 	fi
 
 	counters=$(ip netns exec $ns $tables -v -L OUTPUT | grep DROP)
@@ -115,6 +121,7 @@
 	for v in $values; do
 		if [ $v -ne 0 ]; then
 			echo "FAIL: got $tables $values in ns $ns , not 0 - not all expected packets marked" 1>&2
+			ret=1
 			return 1
 		fi
 	done
@@ -209,11 +216,11 @@
 	fi
 
 	if [ $local_addr = "::" ];then
-		check_mark $listener_ns 6
-		check_mark $connector_ns 6
+		check_mark $listener_ns 6 || retc=1
+		check_mark $connector_ns 6 || retc=1
 	else
-		check_mark $listener_ns 4
-		check_mark $connector_ns 4
+		check_mark $listener_ns 4 || retc=1
+		check_mark $connector_ns 4 || retc=1
 	fi
 
 	check_transfer $cin $sout "file received by server"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/pm_netlink.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/pm_netlink.sh
@@ -1,6 +1,8 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
+. "$(dirname "${0}")/mptcp_lib.sh"
+
 ksft_skip=4
 ret=0
 
@@ -34,6 +36,8 @@
 	ip netns del $ns1
 }
 
+mptcp_lib_check_mptcp
+
 ip -Version > /dev/null 2>&1
 if [ $? -ne 0 ];then
 	echo "SKIP: Could not run test without ip tool"
@@ -69,8 +73,12 @@
 }
 
 check "ip netns exec $ns1 ./pm_nl_ctl dump" "" "defaults addr list"
-check "ip netns exec $ns1 ./pm_nl_ctl limits" "accept 0
+
+default_limits="$(ip netns exec $ns1 ./pm_nl_ctl limits)"
+if mptcp_lib_expect_all_features; then
+	check "ip netns exec $ns1 ./pm_nl_ctl limits" "accept 0
 subflows 0" "defaults limits"
+fi
 
 ip netns exec $ns1 ./pm_nl_ctl add 10.0.1.1
 ip netns exec $ns1 ./pm_nl_ctl add 10.0.1.2 flags subflow dev lo
@@ -117,12 +125,10 @@
 check "ip netns exec $ns1 ./pm_nl_ctl dump" "" "flush addrs"
 
 ip netns exec $ns1 ./pm_nl_ctl limits 9 1
-check "ip netns exec $ns1 ./pm_nl_ctl limits" "accept 0
-subflows 0" "rcv addrs above hard limit"
+check "ip netns exec $ns1 ./pm_nl_ctl limits" "$default_limits" "rcv addrs above hard limit"
 
 ip netns exec $ns1 ./pm_nl_ctl limits 1 9
-check "ip netns exec $ns1 ./pm_nl_ctl limits" "accept 0
-subflows 0" "subflows above hard limit"
+check "ip netns exec $ns1 ./pm_nl_ctl limits" "$default_limits" "subflows above hard limit"
 
 ip netns exec $ns1 ./pm_nl_ctl limits 8 8
 check "ip netns exec $ns1 ./pm_nl_ctl limits" "accept 8
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/mptcp/simult_flows.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/mptcp/simult_flows.sh
@@ -1,6 +1,8 @@
 #!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
+. "$(dirname "${0}")/mptcp_lib.sh"
+
 rndh=$(printf %x $sec)-$(mktemp -u XXXXXX)
 ns1="ns1-$rndh"
 ns2="ns2-$rndh"
@@ -32,6 +34,8 @@
 	done
 }
 
+mptcp_lib_check_mptcp
+
 ip -Version > /dev/null 2>&1
 if [ $? -ne 0 ];then
 	echo "SKIP: Could not run test without ip tool"
@@ -51,7 +55,7 @@
 	sout=$(mktemp)
 	cout=$(mktemp)
 	capout=$(mktemp)
-	size=$((2048 * 4096))
+	size=$((2 * 2048 * 4096))
 	dd if=/dev/zero of=$small bs=4096 count=20 >/dev/null 2>&1
 	dd if=/dev/zero of=$large bs=4096 count=$((size / 4096)) >/dev/null 2>&1
 
@@ -161,17 +165,15 @@
 
 	timeout ${timeout_test} \
 		ip netns exec ${ns3} \
-			./mptcp_connect -jt ${timeout_poll} -l -p $port \
+			./mptcp_connect -jt ${timeout_poll} -l -p $port -T $time \
 				0.0.0.0 < "$sin" > "$sout" &
 	local spid=$!
 
 	wait_local_port_listen "${ns3}" "${port}"
 
-	local start
-	start=$(date +%s%3N)
 	timeout ${timeout_test} \
 		ip netns exec ${ns1} \
-			./mptcp_connect -jt ${timeout_poll} -p $port \
+			./mptcp_connect -jt ${timeout_poll} -p $port -T $time \
 				10.0.3.3 < "$cin" > "$cout" &
 	local cpid=$!
 
@@ -180,27 +182,20 @@
 	wait $spid
 	local rets=$?
 
-	local stop
-	stop=$(date +%s%3N)
-
 	if $capture; then
 		sleep 1
 		kill ${cappid_listener}
 		kill ${cappid_connector}
 	fi
 
-	local duration
-	duration=$((stop-start))
-
 	cmp $sin $cout > /dev/null 2>&1
 	local cmps=$?
 	cmp $cin $sout > /dev/null 2>&1
 	local cmpc=$?
 
-	printf "%16s" "$duration max $max_time "
+	printf "%-16s" " max $max_time "
 	if [ $retc -eq 0 ] && [ $rets -eq 0 ] && \
-	   [ $cmpc -eq 0 ] && [ $cmps -eq 0 ] && \
-	   [ $duration -lt $max_time ]; then
+	   [ $cmpc -eq 0 ] && [ $cmps -eq 0 ]; then
 		echo "[ OK ]"
 		cat "$capout"
 		return 0
@@ -244,23 +239,25 @@
 	tc -n $ns2 qdisc add dev ns2eth1 root netem rate ${rate1}mbit $delay1
 	tc -n $ns2 qdisc add dev ns2eth2 root netem rate ${rate2}mbit $delay2
 
-	# time is measure in ms
-	local time=$((size * 8 * 1000 / (( $rate1 + $rate2) * 1024 *1024) ))
+	# time is measured in ms, account for transfer size, aggregated link speed
+	# and header overhead (10%)
+	#              ms    byte -> bit   10%        mbit      -> kbit -> bit  10%
+	local time=$((1000 * size  *  8  * 10 / ((rate1 + rate2) * 1000 * 1000 * 9) ))
 
 	# mptcp_connect will do some sleeps to allow the mp_join handshake
-	# completion
-	time=$((time + 1350))
+	# completion (see mptcp_connect): 200ms on each side, add some slack
+	time=$((time + 450))
 
-	printf "%-50s" "$msg"
-	do_transfer $small $large $((time * 11 / 10))
+	printf "%-60s" "$msg"
+	do_transfer $small $large $time
 	lret=$?
 	if [ $lret -ne 0 ]; then
 		ret=$lret
 		[ $bail -eq 0 ] || exit $ret
 	fi
 
-	printf "%-50s" "$msg - reverse direction"
-	do_transfer $large $small $((time * 11 / 10))
+	printf "%-60s" "$msg - reverse direction"
+	do_transfer $large $small $time
 	lret=$?
 	if [ $lret -ne 0 ]; then
 		ret=$lret
@@ -292,10 +289,10 @@
 
 setup
 run_test 10 10 0 0 "balanced bwidth"
-run_test 10 10 1 50 "balanced bwidth with unbalanced delay"
+run_test 10 10 1 25 "balanced bwidth with unbalanced delay"
 
 # we still need some additional infrastructure to pass the following test-cases
-run_test 30 10 0 0 "unbalanced bwidth"
-run_test 30 10 1 50 "unbalanced bwidth with unbalanced delay"
-run_test 30 10 50 1 "unbalanced bwidth with opposed, unbalanced delay"
+run_test 10 3 0 0 "unbalanced bwidth"
+run_test 10 3 1 25 "unbalanced bwidth with unbalanced delay"
+run_test 10 3 25 1 "unbalanced bwidth with opposed, unbalanced delay"
 exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/msg_zerocopy.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/msg_zerocopy.c
@@ -85,6 +85,7 @@
 static int  cfg_runtime_ms	= 4200;
 static int  cfg_verbose;
 static int  cfg_waittime_ms	= 500;
+static int  cfg_notification_limit = 32;
 static bool cfg_zerocopy;
 
 static socklen_t cfg_alen;
@@ -95,6 +96,7 @@
 static long packets, bytes, completions, expected_completions;
 static int  zerocopied = -1;
 static uint32_t next_completion;
+static uint32_t sends_since_notify;
 
 static unsigned long gettimeofday_ms(void)
 {
@@ -208,6 +210,7 @@
 		error(1, errno, "send");
 	if (cfg_verbose && ret != len)
 		fprintf(stderr, "send: ret=%u != %u\n", ret, len);
+	sends_since_notify++;
 
 	if (len) {
 		packets++;
@@ -435,7 +438,7 @@
 	/* Detect notification gaps. These should not happen often, if at all.
 	 * Gaps can occur due to drops, reordering and retransmissions.
 	 */
-	if (lo != next_completion)
+	if (cfg_verbose && lo != next_completion)
 		fprintf(stderr, "gap: %u..%u does not append to %u\n",
 			lo, hi, next_completion);
 	next_completion = hi + 1;
@@ -460,6 +463,7 @@
 static void do_recv_completions(int fd, int domain)
 {
 	while (do_recv_completion(fd, domain)) {}
+	sends_since_notify = 0;
 }
 
 /* Wait for all remaining completions on the errqueue */
@@ -549,6 +553,9 @@
 		else
 			do_sendmsg(fd, &msg, cfg_zerocopy, domain);
 
+		if (cfg_zerocopy && sends_since_notify >= cfg_notification_limit)
+			do_recv_completions(fd, domain);
+
 		while (!do_poll(fd, POLLOUT)) {
 			if (cfg_zerocopy)
 				do_recv_completions(fd, domain);
@@ -708,7 +715,7 @@
 
 	cfg_payload_len = max_payload_len;
 
-	while ((c = getopt(argc, argv, "46c:C:D:i:mp:rs:S:t:vz")) != -1) {
+	while ((c = getopt(argc, argv, "46c:C:D:i:l:mp:rs:S:t:vz")) != -1) {
 		switch (c) {
 		case '4':
 			if (cfg_family != PF_UNSPEC)
@@ -736,6 +743,9 @@
 			if (cfg_ifindex == 0)
 				error(1, errno, "invalid iface: %s", optarg);
 			break;
+		case 'l':
+			cfg_notification_limit = strtoul(optarg, NULL, 0);
+			break;
 		case 'm':
 			cfg_cork_mixed = true;
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/net_helper.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/net_helper.sh
@@ -0,0 +1,25 @@
+#!/bin/bash
+# SPDX-License-Identifier: GPL-2.0
+#
+# Helper functions
+
+wait_local_port_listen()
+{
+	local listener_ns="${1}"
+	local port="${2}"
+	local protocol="${3}"
+	local pattern
+	local i
+
+	pattern=":$(printf "%04X" "${port}") "
+
+	# for tcp protocol additionally check the socket state
+	[ ${protocol} = "tcp" ] && pattern="${pattern}0A"
+	for i in $(seq 10); do
+		if ip netns exec "${listener_ns}" awk '{print $2" "$4}' \
+		   /proc/net/"${protocol}"* | grep -q "${pattern}"; then
+			break
+		fi
+		sleep 0.1
+	done
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/pmtu.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/pmtu.sh
@@ -26,6 +26,15 @@
 # - pmtu_ipv6
 #	Same as pmtu_ipv4, except for locked PMTU tests, using IPv6
 #
+# - pmtu_ipv4_dscp_icmp_exception
+#	Set up the same network topology as pmtu_ipv4, but use non-default
+#	routing table in A. A fib-rule is used to jump to this routing table
+#	based on DSCP. Send ICMPv4 packets with the expected DSCP value and
+#	verify that ECN doesn't interfere with the creation of PMTU exceptions.
+#
+# - pmtu_ipv4_dscp_udp_exception
+#	Same as pmtu_ipv4_dscp_icmp_exception, but use UDP instead of ICMP.
+#
 # - pmtu_ipv4_vxlan4_exception
 #	Set up the same network topology as pmtu_ipv4, create a VXLAN tunnel
 #	over IPv4 between A and B, routed via R1. On the link between R1 and B,
@@ -188,6 +197,12 @@
 #
 # - pmtu_ipv6_route_change
 #	Same as above but with IPv6
+#
+# - pmtu_ipv4_mp_exceptions
+#	Use the same topology as in pmtu_ipv4, but add routeable addresses
+#	on host A and B on lo reachable via both routers. Host A and B
+#	addresses have multipath routes to each other, b_r1 mtu = 1500.
+#	Check that PMTU exceptions are created for both paths.
 
 # Kselftest framework requirement - SKIP code is 4.
 ksft_skip=4
@@ -203,6 +218,8 @@
 tests="
 	pmtu_ipv4_exception		ipv4: PMTU exceptions			1
 	pmtu_ipv6_exception		ipv6: PMTU exceptions			1
+	pmtu_ipv4_dscp_icmp_exception	ICMPv4 with DSCP and ECN: PMTU exceptions	1
+	pmtu_ipv4_dscp_udp_exception	UDPv4 with DSCP and ECN: PMTU exceptions	1
 	pmtu_ipv4_vxlan4_exception	IPv4 over vxlan4: PMTU exceptions	1
 	pmtu_ipv6_vxlan4_exception	IPv6 over vxlan4: PMTU exceptions	1
 	pmtu_ipv4_vxlan6_exception	IPv4 over vxlan6: PMTU exceptions	1
@@ -255,7 +272,8 @@
 	list_flush_ipv4_exception	ipv4: list and flush cached exceptions	1
 	list_flush_ipv6_exception	ipv6: list and flush cached exceptions	1
 	pmtu_ipv4_route_change		ipv4: PMTU exception w/route replace	1
-	pmtu_ipv6_route_change		ipv6: PMTU exception w/route replace	1"
+	pmtu_ipv6_route_change		ipv6: PMTU exception w/route replace	1
+	pmtu_ipv4_mp_exceptions		ipv4: PMTU multipath nh exceptions	1"
 
 NS_A="ns-A"
 NS_B="ns-B"
@@ -323,6 +341,9 @@
 	B	6	default			61
 "
 
+policy_mark=0x04
+rt_table=main
+
 veth4_a_addr="192.168.1.1"
 veth4_b_addr="192.168.1.2"
 veth4_c_addr="192.168.2.10"
@@ -339,6 +360,9 @@
 tunnel6_b_addr="fd00:2::b"
 tunnel6_mask="64"
 
+host4_a_addr="192.168.99.99"
+host4_b_addr="192.168.88.88"
+
 dummy6_0_prefix="fc00:1000::"
 dummy6_1_prefix="fc00:1001::"
 dummy6_mask="64"
@@ -346,6 +370,7 @@
 err_buf=
 tcpdump_pids=
 nettest_pids=
+socat_pids=
 
 err() {
 	err_buf="${err_buf}${1}
@@ -374,6 +399,16 @@
 	return $rc
 }
 
+run_cmd_bg() {
+	cmd="$*"
+
+	if [ "$VERBOSE" = "1" ]; then
+		printf "    COMMAND: %s &\n" "${cmd}"
+	fi
+
+	$cmd 2>&1 &
+}
+
 # Find the auto-generated name for this namespace
 nsname() {
 	eval echo \$NS_$1
@@ -661,19 +696,21 @@
 }
 
 setup_nettest_xfrm() {
-	which nettest >/dev/null
-	if [ $? -ne 0 ]; then
-		echo "'nettest' command not found; skipping tests"
-	        return 1
+	if ! which nettest >/dev/null; then
+		PATH=$PWD:$PATH
+		if ! which nettest >/dev/null; then
+			echo "'nettest' command not found; skipping tests"
+			return 1
+		fi
 	fi
 
 	[ ${1} -eq 6 ] && proto="-6" || proto=""
 	port=${2}
 
-	run_cmd ${ns_a} nettest ${proto} -q -D -s -x -p ${port} -t 5 &
+	run_cmd_bg "${ns_a}" nettest "${proto}" -q -D -s -x -p "${port}" -t 5
 	nettest_pids="${nettest_pids} $!"
 
-	run_cmd ${ns_b} nettest ${proto} -q -D -s -x -p ${port} -t 5 &
+	run_cmd_bg "${ns_b}" nettest "${proto}" -q -D -s -x -p "${port}" -t 5
 	nettest_pids="${nettest_pids} $!"
 }
 
@@ -686,23 +723,23 @@
 }
 
 setup_xfrm4udp() {
-	setup_xfrm 4 ${veth4_a_addr} ${veth4_b_addr} "encap espinudp 4500 4500 0.0.0.0"
-	setup_nettest_xfrm 4 4500
+	setup_xfrm 4 ${veth4_a_addr} ${veth4_b_addr} "encap espinudp 4500 4500 0.0.0.0" && \
+		setup_nettest_xfrm 4 4500
 }
 
 setup_xfrm6udp() {
-	setup_xfrm 6 ${veth6_a_addr} ${veth6_b_addr} "encap espinudp 4500 4500 0.0.0.0"
-	setup_nettest_xfrm 6 4500
+	setup_xfrm 6 ${veth6_a_addr} ${veth6_b_addr} "encap espinudp 4500 4500 0.0.0.0" && \
+		setup_nettest_xfrm 6 4500
 }
 
 setup_xfrm4udprouted() {
-	setup_xfrm 4 ${prefix4}.${a_r1}.1 ${prefix4}.${b_r1}.1 "encap espinudp 4500 4500 0.0.0.0"
-	setup_nettest_xfrm 4 4500
+	setup_xfrm 4 ${prefix4}.${a_r1}.1 ${prefix4}.${b_r1}.1 "encap espinudp 4500 4500 0.0.0.0" && \
+		setup_nettest_xfrm 4 4500
 }
 
 setup_xfrm6udprouted() {
-	setup_xfrm 6 ${prefix6}:${a_r1}::1 ${prefix6}:${b_r1}::1 "encap espinudp 4500 4500 0.0.0.0"
-	setup_nettest_xfrm 6 4500
+	setup_xfrm 6 ${prefix6}:${a_r1}::1 ${prefix6}:${b_r1}::1 "encap espinudp 4500 4500 0.0.0.0" && \
+		setup_nettest_xfrm 6 4500
 }
 
 setup_routing_old() {
@@ -713,7 +750,7 @@
 
 		ns_name="$(nsname ${ns})"
 
-		ip -n ${ns_name} route add ${addr} via ${gw}
+		ip -n "${ns_name}" route add "${addr}" table "${rt_table}" via "${gw}"
 
 		ns=""; addr=""; gw=""
 	done
@@ -743,7 +780,7 @@
 
 		ns_name="$(nsname ${ns})"
 
-		ip -n ${ns_name} -${fam} route add ${addr} nhid ${nhid}
+		ip -n "${ns_name}" -"${fam}" route add "${addr}" table "${rt_table}" nhid "${nhid}"
 
 		ns=""; fam=""; addr=""; nhid=""
 	done
@@ -788,6 +825,24 @@
 	return 0
 }
 
+setup_policy_routing() {
+	setup_routing
+
+	ip -netns "${NS_A}" -4 rule add dsfield "${policy_mark}" \
+		table "${rt_table}"
+
+	# Set the IPv4 Don't Fragment bit with tc, since socat doesn't seem to
+	# have an option do to it.
+	tc -netns "${NS_A}" qdisc replace dev veth_A-R1 root prio
+	tc -netns "${NS_A}" qdisc replace dev veth_A-R2 root prio
+	tc -netns "${NS_A}" filter add dev veth_A-R1                      \
+		protocol ipv4 flower ip_proto udp                         \
+		action pedit ex munge ip df set 0x40 pipe csum ip and udp
+	tc -netns "${NS_A}" filter add dev veth_A-R2                      \
+		protocol ipv4 flower ip_proto udp                         \
+		action pedit ex munge ip df set 0x40 pipe csum ip and udp
+}
+
 setup_bridge() {
 	run_cmd ${ns_a} ip link add br0 type bridge || return $ksft_skip
 	run_cmd ${ns_a} ip link set br0 up
@@ -862,10 +917,55 @@
 	run_cmd ip route add ${prefix6}:${b_r1}::1 via ${prefix6}:${a_r1}::2
 }
 
+setup_multipath_new() {
+	# Set up host A with multipath routes to host B host4_b_addr
+	run_cmd ${ns_a} ip addr add ${host4_a_addr} dev lo
+	run_cmd ${ns_a} ip nexthop add id 401 via ${prefix4}.${a_r1}.2 dev veth_A-R1
+	run_cmd ${ns_a} ip nexthop add id 402 via ${prefix4}.${a_r2}.2 dev veth_A-R2
+	run_cmd ${ns_a} ip nexthop add id 403 group 401/402
+	run_cmd ${ns_a} ip route add ${host4_b_addr} src ${host4_a_addr} nhid 403
+
+	# Set up host B with multipath routes to host A host4_a_addr
+	run_cmd ${ns_b} ip addr add ${host4_b_addr} dev lo
+	run_cmd ${ns_b} ip nexthop add id 401 via ${prefix4}.${b_r1}.2 dev veth_B-R1
+	run_cmd ${ns_b} ip nexthop add id 402 via ${prefix4}.${b_r2}.2 dev veth_B-R2
+	run_cmd ${ns_b} ip nexthop add id 403 group 401/402
+	run_cmd ${ns_b} ip route add ${host4_a_addr} src ${host4_b_addr} nhid 403
+}
+
+setup_multipath_old() {
+	# Set up host A with multipath routes to host B host4_b_addr
+	run_cmd ${ns_a} ip addr add ${host4_a_addr} dev lo
+	run_cmd ${ns_a} ip route add ${host4_b_addr} \
+			src ${host4_a_addr} \
+			nexthop via ${prefix4}.${a_r1}.2 weight 1 \
+			nexthop via ${prefix4}.${a_r2}.2 weight 1
+
+	# Set up host B with multipath routes to host A host4_a_addr
+	run_cmd ${ns_b} ip addr add ${host4_b_addr} dev lo
+	run_cmd ${ns_b} ip route add ${host4_a_addr} \
+			src ${host4_b_addr} \
+			nexthop via ${prefix4}.${b_r1}.2 weight 1 \
+			nexthop via ${prefix4}.${b_r2}.2 weight 1
+}
+
+setup_multipath() {
+	if [ "$USE_NH" = "yes" ]; then
+		setup_multipath_new
+	else
+		setup_multipath_old
+	fi
+
+	# Set up routers with routes to dummies
+	run_cmd ${ns_r1} ip route add ${host4_a_addr} via ${prefix4}.${a_r1}.1
+	run_cmd ${ns_r2} ip route add ${host4_a_addr} via ${prefix4}.${a_r2}.1
+	run_cmd ${ns_r1} ip route add ${host4_b_addr} via ${prefix4}.${b_r1}.1
+	run_cmd ${ns_r2} ip route add ${host4_b_addr} via ${prefix4}.${b_r2}.1
+}
+
 setup() {
 	[ "$(id -u)" -ne 0 ] && echo "  need to run as root" && return $ksft_skip
 
-	cleanup
 	for arg do
 		eval setup_${arg} || { echo "  ${arg} not supported"; return 1; }
 	done
@@ -876,7 +976,7 @@
 
 	for arg do
 		[ "${ns_cmd}" = "" ] && ns_cmd="${arg}" && continue
-		${ns_cmd} tcpdump -s 0 -i "${arg}" -w "${name}_${arg}.pcap" 2> /dev/null &
+		${ns_cmd} tcpdump --immediate-mode -s 0 -i "${arg}" -w "${name}_${arg}.pcap" 2> /dev/null &
 		tcpdump_pids="${tcpdump_pids} $!"
 		ns_cmd=
 	done
@@ -894,6 +994,11 @@
 	done
 	nettest_pids=
 
+	for pid in ${socat_pids}; do
+		kill "${pid}"
+	done
+	socat_pids=
+
 	for n in ${NS_A} ${NS_B} ${NS_C} ${NS_R1} ${NS_R2}; do
 		ip netns del ${n} 2> /dev/null
 	done
@@ -939,17 +1044,15 @@
 }
 
 route_get_dst_exception() {
-	ns_cmd="${1}"
-	dst="${2}"
+	ns_cmd="${1}"; shift
 
-	${ns_cmd} ip route get "${dst}"
+	${ns_cmd} ip route get "$@"
 }
 
 route_get_dst_pmtu_from_exception() {
-	ns_cmd="${1}"
-	dst="${2}"
+	ns_cmd="${1}"; shift
 
-	mtu_parse "$(route_get_dst_exception "${ns_cmd}" ${dst})"
+	mtu_parse "$(route_get_dst_exception "${ns_cmd}" "$@")"
 }
 
 check_pmtu_value() {
@@ -1059,6 +1162,95 @@
 	test_pmtu_ipvX 6
 }
 
+test_pmtu_ipv4_dscp_icmp_exception() {
+	rt_table=100
+
+	setup namespaces policy_routing || return $ksft_skip
+	trace "${ns_a}"  veth_A-R1    "${ns_r1}" veth_R1-A \
+	      "${ns_r1}" veth_R1-B    "${ns_b}"  veth_B-R1 \
+	      "${ns_a}"  veth_A-R2    "${ns_r2}" veth_R2-A \
+	      "${ns_r2}" veth_R2-B    "${ns_b}"  veth_B-R2
+
+	# Set up initial MTU values
+	mtu "${ns_a}"  veth_A-R1 2000
+	mtu "${ns_r1}" veth_R1-A 2000
+	mtu "${ns_r1}" veth_R1-B 1400
+	mtu "${ns_b}"  veth_B-R1 1400
+
+	mtu "${ns_a}"  veth_A-R2 2000
+	mtu "${ns_r2}" veth_R2-A 2000
+	mtu "${ns_r2}" veth_R2-B 1500
+	mtu "${ns_b}"  veth_B-R2 1500
+
+	len=$((2000 - 20 - 8)) # Fills MTU of veth_A-R1
+
+	dst1="${prefix4}.${b_r1}.1"
+	dst2="${prefix4}.${b_r2}.1"
+
+	# Create route exceptions
+	dsfield=${policy_mark} # No ECN bit set (Not-ECT)
+	run_cmd "${ns_a}" ping -q -M want -Q "${dsfield}" -c 1 -w 1 -s "${len}" "${dst1}"
+
+	dsfield=$(printf "%#x" $((policy_mark + 0x02))) # ECN=2 (ECT(0))
+	run_cmd "${ns_a}" ping -q -M want -Q "${dsfield}" -c 1 -w 1 -s "${len}" "${dst2}"
+
+	# Check that exceptions have been created with the correct PMTU
+	pmtu_1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst1}" dsfield "${policy_mark}")"
+	check_pmtu_value "1400" "${pmtu_1}" "exceeding MTU" || return 1
+
+	pmtu_2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst2}" dsfield "${policy_mark}")"
+	check_pmtu_value "1500" "${pmtu_2}" "exceeding MTU" || return 1
+}
+
+test_pmtu_ipv4_dscp_udp_exception() {
+	rt_table=100
+
+	if ! which socat > /dev/null 2>&1; then
+		echo "'socat' command not found; skipping tests"
+		return $ksft_skip
+	fi
+
+	setup namespaces policy_routing || return $ksft_skip
+	trace "${ns_a}"  veth_A-R1    "${ns_r1}" veth_R1-A \
+	      "${ns_r1}" veth_R1-B    "${ns_b}"  veth_B-R1 \
+	      "${ns_a}"  veth_A-R2    "${ns_r2}" veth_R2-A \
+	      "${ns_r2}" veth_R2-B    "${ns_b}"  veth_B-R2
+
+	# Set up initial MTU values
+	mtu "${ns_a}"  veth_A-R1 2000
+	mtu "${ns_r1}" veth_R1-A 2000
+	mtu "${ns_r1}" veth_R1-B 1400
+	mtu "${ns_b}"  veth_B-R1 1400
+
+	mtu "${ns_a}"  veth_A-R2 2000
+	mtu "${ns_r2}" veth_R2-A 2000
+	mtu "${ns_r2}" veth_R2-B 1500
+	mtu "${ns_b}"  veth_B-R2 1500
+
+	len=$((2000 - 20 - 8)) # Fills MTU of veth_A-R1
+
+	dst1="${prefix4}.${b_r1}.1"
+	dst2="${prefix4}.${b_r2}.1"
+
+	# Create route exceptions
+	run_cmd_bg "${ns_b}" socat UDP-LISTEN:50000 OPEN:/dev/null,wronly=1
+	socat_pids="${socat_pids} $!"
+
+	dsfield=${policy_mark} # No ECN bit set (Not-ECT)
+	run_cmd "${ns_a}" socat OPEN:/dev/zero,rdonly=1,readbytes="${len}" \
+		UDP:"${dst1}":50000,tos="${dsfield}"
+
+	dsfield=$(printf "%#x" $((policy_mark + 0x02))) # ECN=2 (ECT(0))
+	run_cmd "${ns_a}" socat OPEN:/dev/zero,rdonly=1,readbytes="${len}" \
+		UDP:"${dst2}":50000,tos="${dsfield}"
+
+	# Check that exceptions have been created with the correct PMTU
+	pmtu_1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst1}" dsfield "${policy_mark}")"
+	check_pmtu_value "1400" "${pmtu_1}" "exceeding MTU" || return 1
+	pmtu_2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst2}" dsfield "${policy_mark}")"
+	check_pmtu_value "1500" "${pmtu_2}" "exceeding MTU" || return 1
+}
+
 test_pmtu_ipvX_over_vxlanY_or_geneveY_exception() {
 	type=${1}
 	family=${2}
@@ -1784,6 +1976,13 @@
 	return 0
 }
 
+check_running() {
+	pid=${1}
+	cmd=${2}
+
+	[ "$(cat /proc/${pid}/cmdline 2>/dev/null | tr -d '\0')" = "${cmd}" ]
+}
+
 test_cleanup_vxlanX_exception() {
 	outer="${1}"
 	encap="vxlan"
@@ -1814,11 +2013,12 @@
 
 	${ns_a} ip link del dev veth_A-R1 &
 	iplink_pid=$!
-	sleep 1
-	if [ "$(cat /proc/${iplink_pid}/cmdline 2>/dev/null | tr -d '\0')" = "iplinkdeldevveth_A-R1" ]; then
-		err "  can't delete veth device in a timely manner, PMTU dst likely leaked"
-		return 1
-	fi
+	for i in $(seq 1 20); do
+		check_running ${iplink_pid} "iplinkdeldevveth_A-R1" || return 0
+		sleep 0.1
+	done
+	err "  can't delete veth device in a timely manner, PMTU dst likely leaked"
+	return 1
 }
 
 test_cleanup_ipv6_exception() {
@@ -1836,6 +2036,10 @@
 
 	unset IFS
 
+	# Since cleanup() relies on variables modified by this subshell, it
+	# has to run in this context.
+	trap cleanup EXIT
+
 	if [ "$VERBOSE" = "1" ]; then
 		printf "\n##########################################################################\n\n"
 	fi
@@ -1865,7 +2069,7 @@
 	case $ret in
 		0)
 			all_skipped=false
-			[ $exitcode=$ksft_skip ] && exitcode=0
+			[ $exitcode -eq $ksft_skip ] && exitcode=0
 		;;
 		$ksft_skip)
 			[ $all_skipped = true ] && exitcode=$ksft_skip
@@ -2049,6 +2253,36 @@
 	test_pmtu_ipvX_route_change 6
 }
 
+test_pmtu_ipv4_mp_exceptions() {
+	setup namespaces routing multipath || return $ksft_skip
+
+	trace "${ns_a}"  veth_A-R1    "${ns_r1}" veth_R1-A \
+	      "${ns_r1}" veth_R1-B    "${ns_b}"  veth_B-R1 \
+	      "${ns_a}"  veth_A-R2    "${ns_r2}" veth_R2-A \
+	      "${ns_r2}" veth_R2-B    "${ns_b}"  veth_B-R2
+
+	# Set up initial MTU values
+	mtu "${ns_a}"  veth_A-R1 2000
+	mtu "${ns_r1}" veth_R1-A 2000
+	mtu "${ns_r1}" veth_R1-B 1500
+	mtu "${ns_b}"  veth_B-R1 1500
+
+	mtu "${ns_a}"  veth_A-R2 2000
+	mtu "${ns_r2}" veth_R2-A 2000
+	mtu "${ns_r2}" veth_R2-B 1500
+	mtu "${ns_b}"  veth_B-R2 1500
+
+	# Ping and expect two nexthop exceptions for two routes
+	run_cmd ${ns_a} ping -q -M want -i 0.1 -c 1 -s 1800 "${host4_b_addr}"
+
+	# Check that exceptions have been created with the correct PMTU
+	pmtu_a_R1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${host4_b_addr}" oif veth_A-R1)"
+	pmtu_a_R2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${host4_b_addr}" oif veth_A-R2)"
+
+	check_pmtu_value "1500" "${pmtu_a_R1}" "exceeding MTU (veth_A-R1)" || return 1
+	check_pmtu_value "1500" "${pmtu_a_R2}" "exceeding MTU (veth_A-R2)" || return 1
+}
+
 usage() {
 	echo
 	echo "$0 [OPTIONS] [TEST]..."
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/reuseaddr_conflict.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/reuseaddr_conflict.c
@@ -109,6 +109,6 @@
 	fd1 = open_port(0, 1);
 	if (fd1 >= 0)
 		error(1, 0, "Was allowed to create an ipv4 reuseport on an already bound non-reuseport socket with no ipv6");
-	fprintf(stderr, "Success");
+	fprintf(stderr, "Success\n");
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/reuseport_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/reuseport_bpf.c
@@ -330,7 +330,7 @@
 	if (bind(fd1, addr, sockaddr_size()))
 		error(1, errno, "failed to bind recv socket 1");
 
-	if (!bind(fd2, addr, sockaddr_size()) && errno != EADDRINUSE)
+	if (!bind(fd2, addr, sockaddr_size()) || errno != EADDRINUSE)
 		error(1, errno, "bind socket 2 should fail with EADDRINUSE");
 
 	free(addr);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/reuseport_bpf_numa.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/reuseport_bpf_numa.c
@@ -211,12 +211,16 @@
 
 	/* Forward iterate */
 	for (node = 0; node < len; ++node) {
+		if (!numa_bitmask_isbitset(numa_nodes_ptr, node))
+			continue;
 		send_from_node(node, family, proto);
 		receive_on_node(rcv_fd, len, epfd, node, proto);
 	}
 
 	/* Reverse iterate */
 	for (node = len - 1; node >= 0; --node) {
+		if (!numa_bitmask_isbitset(numa_nodes_ptr, node))
+			continue;
 		send_from_node(node, family, proto);
 		receive_on_node(rcv_fd, len, epfd, node, proto);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/rtnetlink.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/rtnetlink.sh
@@ -782,7 +782,7 @@
 	    tmpl proto esp src $srcip dst $dstip spi 9 \
 	    mode transport reqid 42
 	check_err $?
-	ip x p add dir out src $dstip/24 dst $srcip/24 \
+	ip x p add dir in src $dstip/24 dst $srcip/24 \
 	    tmpl proto esp src $dstip dst $srcip spi 9 \
 	    mode transport reqid 42
 	check_err $?
@@ -813,10 +813,10 @@
 	# does driver have correct offload info
 	diff $sysfsf - << EOF
 SA count=2 tx=3
-sa[0] tx ipaddr=0x00000000 00000000 00000000 00000000
+sa[0] tx ipaddr=$dstip
 sa[0]    spi=0x00000009 proto=0x32 salt=0x61626364 crypt=1
 sa[0]    key=0x34333231 38373635 32313039 36353433
-sa[1] rx ipaddr=0x00000000 00000000 00000000 037ba8c0
+sa[1] rx ipaddr=$srcip
 sa[1]    spi=0x00000009 proto=0x32 salt=0x61626364 crypt=1
 sa[1]    key=0x34333231 38373635 32313039 36353433
 EOF
@@ -835,6 +835,7 @@
 	fi
 
 	# clean up any leftovers
+	echo 0 > /sys/bus/netdevsim/del_device
 	$probed && rmmod netdevsim
 
 	if [ $ret -ne 0 ]; then
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/settings
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/settings
@@ -1 +1 @@
-timeout=300
+timeout=0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/setup_veth.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/setup_veth.sh
@@ -8,7 +8,7 @@
 	local -r ns_mac="$4"
 
 	[[ -e /var/run/netns/"${ns_name}" ]] || ip netns add "${ns_name}"
-	echo 100000 > "/sys/class/net/${ns_dev}/gro_flush_timeout"
+	echo 1000000 > "/sys/class/net/${ns_dev}/gro_flush_timeout"
 	ip link set dev "${ns_dev}" netns "${ns_name}" mtu 65535
 	ip -netns "${ns_name}" link set dev "${ns_dev}" up
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/so_txtime.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/so_txtime.c
@@ -421,7 +421,7 @@
 			"Options:\n"
 			"  -4            only IPv4\n"
 			"  -6            only IPv6\n"
-			"  -c <clock>    monotonic (default) or tai\n"
+			"  -c <clock>    monotonic or tai (default)\n"
 			"  -D <addr>     destination IP address (server)\n"
 			"  -S <addr>     source IP address (client)\n"
 			"  -r            run rx mode\n"
@@ -475,7 +475,7 @@
 			cfg_rx = true;
 			break;
 		case 't':
-			cfg_start_time_ns = strtol(optarg, NULL, 0);
+			cfg_start_time_ns = strtoll(optarg, NULL, 0);
 			break;
 		case 'm':
 			cfg_mark = strtol(optarg, NULL, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/socket.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/socket.c
@@ -6,6 +6,7 @@
 #include <sys/types.h>
 #include <sys/socket.h>
 #include <netinet/in.h>
+#include <limits.h>
 
 struct socket_testcase {
 	int	domain;
@@ -24,7 +25,10 @@
 };
 
 static struct socket_testcase tests[] = {
-	{ AF_MAX,  0,           0,           -EAFNOSUPPORT,    0 },
+	/* libc might have a smaller value of AF_MAX than the kernel
+	 * actually supports, so use INT_MAX instead.
+	 */
+	{ INT_MAX, 0,           0,           -EAFNOSUPPORT,    0  },
 	{ AF_INET, SOCK_STREAM, IPPROTO_TCP, 0,                1  },
 	{ AF_INET, SOCK_DGRAM,  IPPROTO_TCP, -EPROTONOSUPPORT, 1  },
 	{ AF_INET, SOCK_DGRAM,  IPPROTO_UDP, 0,                1  },
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/srv6_end_dt46_l3vpn_test.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/srv6_end_dt46_l3vpn_test.sh
@@ -292,6 +292,11 @@
 	ip netns exec ${hsname} sysctl -wq net.ipv6.conf.all.accept_dad=0
 	ip netns exec ${hsname} sysctl -wq net.ipv6.conf.default.accept_dad=0
 
+	# disable the rp_filter otherwise the kernel gets confused about how
+	# to route decap ipv4 packets.
+	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.all.rp_filter=0
+	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.default.rp_filter=0
+
 	ip -netns ${hsname} link add veth0 type veth peer name ${rtveth}
 	ip -netns ${hsname} link set ${rtveth} netns ${rtname}
 	ip -netns ${hsname} addr add ${IPv6_HS_NETWORK}::${hs}/64 dev veth0 nodad
@@ -316,11 +321,6 @@
 	ip netns exec ${rtname} sysctl -wq net.ipv6.conf.${rtveth}.proxy_ndp=1
 	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.${rtveth}.proxy_arp=1
 
-	# disable the rp_filter otherwise the kernel gets confused about how
-	# to route decap ipv4 packets.
-	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.all.rp_filter=0
-	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.${rtveth}.rp_filter=0
-
 	ip netns exec ${rtname} sh -c "echo 1 > /proc/sys/net/vrf/strict_mode"
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/srv6_end_dt4_l3vpn_test.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/srv6_end_dt4_l3vpn_test.sh
@@ -232,10 +232,14 @@
 	local nsname=rt-${rt}
 
 	ip netns add ${nsname}
+
+	ip netns exec ${nsname} sysctl -wq net.ipv6.conf.all.accept_dad=0
+	ip netns exec ${nsname} sysctl -wq net.ipv6.conf.default.accept_dad=0
+
 	ip link set veth-rt-${rt} netns ${nsname}
 	ip -netns ${nsname} link set veth-rt-${rt} name veth0
 
-	ip -netns ${nsname} addr add ${IPv6_RT_NETWORK}::${rt}/64 dev veth0
+	ip -netns ${nsname} addr add ${IPv6_RT_NETWORK}::${rt}/64 dev veth0 nodad
 	ip -netns ${nsname} link set veth0 up
 	ip -netns ${nsname} link set lo up
 
@@ -254,6 +258,12 @@
 
 	# set the networking for the host
 	ip netns add ${hsname}
+
+	# disable the rp_filter otherwise the kernel gets confused about how
+	# to route decap ipv4 packets.
+	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.all.rp_filter=0
+	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.default.rp_filter=0
+
 	ip -netns ${hsname} link add veth0 type veth peer name ${rtveth}
 	ip -netns ${hsname} link set ${rtveth} netns ${rtname}
 	ip -netns ${hsname} addr add ${IPv4_HS_NETWORK}.${hs}/24 dev veth0
@@ -272,11 +282,6 @@
 
 	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.${rtveth}.proxy_arp=1
 
-	# disable the rp_filter otherwise the kernel gets confused about how
-	# to route decap ipv4 packets.
-	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.all.rp_filter=0
-	ip netns exec ${rtname} sysctl -wq net.ipv4.conf.${rtveth}.rp_filter=0
-
 	ip netns exec ${rtname} sh -c "echo 1 > /proc/sys/net/vrf/strict_mode"
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/test_vxlan_under_vrf.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/test_vxlan_under_vrf.sh
@@ -101,6 +101,8 @@
     ip -netns hv-$id link set veth-tap master br0
     ip -netns hv-$id link set veth-tap up
 
+    ip link set veth-hv address 02:1d:8d:dd:0c:6$id
+
     ip link set veth-hv netns vm-$id
     ip -netns vm-$id addr add 10.0.0.$id/24 dev veth-hv
     ip -netns vm-$id link set veth-hv up
@@ -118,11 +120,11 @@
 
 # Move the underlay to a non-default VRF
 ip -netns hv-1 link set veth0 vrf vrf-underlay
-ip -netns hv-1 link set veth0 down
-ip -netns hv-1 link set veth0 up
+ip -netns hv-1 link set vxlan0 down
+ip -netns hv-1 link set vxlan0 up
 ip -netns hv-2 link set veth0 vrf vrf-underlay
-ip -netns hv-2 link set veth0 down
-ip -netns hv-2 link set veth0 up
+ip -netns hv-2 link set vxlan0 down
+ip -netns hv-2 link set vxlan0 up
 
 echo -n "Check VM connectivity through VXLAN (underlay in a VRF)            "
 ip netns exec vm-1 ping -c 1 -W 1 10.0.0.2 &> /dev/null || (echo "[FAIL]"; false)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/timestamping.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/timestamping.c
@@ -325,8 +325,8 @@
 	struct ifreq device;
 	struct ifreq hwtstamp;
 	struct hwtstamp_config hwconfig, hwconfig_requested;
-	struct so_timestamping so_timestamping_get = { 0, -1 };
-	struct so_timestamping so_timestamping = { 0, -1 };
+	struct so_timestamping so_timestamping_get = { 0, 0 };
+	struct so_timestamping so_timestamping = { 0, 0 };
 	struct sockaddr_in addr;
 	struct ip_mreq imr;
 	struct in_addr iaddr;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/tls.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/tls.c
@@ -25,6 +25,8 @@
 #define TLS_PAYLOAD_MAX_LEN 16384
 #define SOL_TLS 282
 
+static int fips_enabled;
+
 struct tls_crypto_info_keys {
 	union {
 		struct tls12_crypto_info_aes_gcm_128 aes128;
@@ -146,6 +148,7 @@
 {
 	uint16_t tls_version;
 	uint16_t cipher_type;
+	bool fips_non_compliant;
 };
 
 FIXTURE_VARIANT_ADD(tls, 12_gcm)
@@ -164,12 +167,14 @@
 {
 	.tls_version = TLS_1_2_VERSION,
 	.cipher_type = TLS_CIPHER_CHACHA20_POLY1305,
+	.fips_non_compliant = true,
 };
 
 FIXTURE_VARIANT_ADD(tls, 13_chacha)
 {
 	.tls_version = TLS_1_3_VERSION,
 	.cipher_type = TLS_CIPHER_CHACHA20_POLY1305,
+	.fips_non_compliant = true,
 };
 
 FIXTURE_SETUP(tls)
@@ -182,6 +187,9 @@
 	self->notls = false;
 	len = sizeof(addr);
 
+	if (fips_enabled && variant->fips_non_compliant)
+		SKIP(return, "Unsupported cipher in FIPS mode");
+
 	tls_crypto_info_init(variant->tls_version, variant->cipher_type,
 			     &tls12);
 
@@ -268,64 +276,6 @@
 	EXPECT_EQ(recv(self->cfd, buf, st.st_size, MSG_WAITALL), st.st_size);
 }
 
-static void chunked_sendfile(struct __test_metadata *_metadata,
-			     struct _test_data_tls *self,
-			     uint16_t chunk_size,
-			     uint16_t extra_payload_size)
-{
-	char buf[TLS_PAYLOAD_MAX_LEN];
-	uint16_t test_payload_size;
-	int size = 0;
-	int ret;
-	char filename[] = "/tmp/mytemp.XXXXXX";
-	int fd = mkstemp(filename);
-	off_t offset = 0;
-
-	unlink(filename);
-	ASSERT_GE(fd, 0);
-	EXPECT_GE(chunk_size, 1);
-	test_payload_size = chunk_size + extra_payload_size;
-	ASSERT_GE(TLS_PAYLOAD_MAX_LEN, test_payload_size);
-	memset(buf, 1, test_payload_size);
-	size = write(fd, buf, test_payload_size);
-	EXPECT_EQ(size, test_payload_size);
-	fsync(fd);
-
-	while (size > 0) {
-		ret = sendfile(self->fd, fd, &offset, chunk_size);
-		EXPECT_GE(ret, 0);
-		size -= ret;
-	}
-
-	EXPECT_EQ(recv(self->cfd, buf, test_payload_size, MSG_WAITALL),
-		  test_payload_size);
-
-	close(fd);
-}
-
-TEST_F(tls, multi_chunk_sendfile)
-{
-	chunked_sendfile(_metadata, self, 4096, 4096);
-	chunked_sendfile(_metadata, self, 4096, 0);
-	chunked_sendfile(_metadata, self, 4096, 1);
-	chunked_sendfile(_metadata, self, 4096, 2048);
-	chunked_sendfile(_metadata, self, 8192, 2048);
-	chunked_sendfile(_metadata, self, 4096, 8192);
-	chunked_sendfile(_metadata, self, 8192, 4096);
-	chunked_sendfile(_metadata, self, 12288, 1024);
-	chunked_sendfile(_metadata, self, 12288, 2000);
-	chunked_sendfile(_metadata, self, 15360, 100);
-	chunked_sendfile(_metadata, self, 15360, 300);
-	chunked_sendfile(_metadata, self, 1, 4096);
-	chunked_sendfile(_metadata, self, 2048, 4096);
-	chunked_sendfile(_metadata, self, 2048, 8192);
-	chunked_sendfile(_metadata, self, 4096, 8192);
-	chunked_sendfile(_metadata, self, 1024, 12288);
-	chunked_sendfile(_metadata, self, 2000, 12288);
-	chunked_sendfile(_metadata, self, 100, 15360);
-	chunked_sendfile(_metadata, self, 300, 15360);
-}
-
 TEST_F(tls, recv_max)
 {
 	unsigned int send_len = TLS_PAYLOAD_MAX_LEN;
@@ -441,11 +391,11 @@
 
 		msg.msg_iov = &vec;
 		msg.msg_iovlen = 1;
-		EXPECT_EQ(sendmsg(self->cfd, &msg, 0), send_len);
+		EXPECT_EQ(sendmsg(self->fd, &msg, 0), send_len);
 	}
 
 	while (recvs++ < sends) {
-		EXPECT_NE(recv(self->fd, mem, send_len, 0), -1);
+		EXPECT_NE(recv(self->cfd, mem, send_len, 0), -1);
 	}
 
 	free(mem);
@@ -474,9 +424,9 @@
 	msg.msg_iov = vec;
 	msg.msg_iovlen = iov_len;
 
-	EXPECT_EQ(sendmsg(self->cfd, &msg, 0), total_len);
+	EXPECT_EQ(sendmsg(self->fd, &msg, 0), total_len);
 	buf = malloc(total_len);
-	EXPECT_NE(recv(self->fd, buf, total_len, 0), -1);
+	EXPECT_NE(recv(self->cfd, buf, total_len, 0), -1);
 	for (i = 0; i < iov_len; i++) {
 		EXPECT_EQ(memcmp(test_strs[i], buf + len_cmp,
 				 strlen(test_strs[i])),
@@ -716,12 +666,12 @@
 
 	memset(recv_mem, 0, sizeof(recv_mem));
 	EXPECT_EQ(send(self->fd, test_str, send_len, 0), send_len);
-	EXPECT_NE(recv(self->cfd, recv_mem, strlen(test_str_first),
-		       MSG_WAITALL), -1);
+	EXPECT_EQ(recv(self->cfd, recv_mem, strlen(test_str_first),
+		       MSG_WAITALL), strlen(test_str_first));
 	EXPECT_EQ(memcmp(test_str_first, recv_mem, strlen(test_str_first)), 0);
 	memset(recv_mem, 0, sizeof(recv_mem));
-	EXPECT_NE(recv(self->cfd, recv_mem, strlen(test_str_second),
-		       MSG_WAITALL), -1);
+	EXPECT_EQ(recv(self->cfd, recv_mem, strlen(test_str_second),
+		       MSG_WAITALL), strlen(test_str_second));
 	EXPECT_EQ(memcmp(test_str_second, recv_mem, strlen(test_str_second)),
 		  0);
 }
@@ -1394,4 +1344,17 @@
 	close(cfd);
 }
 
+static void __attribute__((constructor)) fips_check(void) {
+	int res;
+	FILE *f;
+
+	f = fopen("/proc/sys/crypto/fips_enabled", "r");
+	if (f) {
+		res = fscanf(f, "%d", &fips_enabled);
+		if (res != 1)
+			ksft_print_msg("ERROR: Couldn't read /proc/sys/crypto/fips_enabled\n");
+		fclose(f);
+	}
+}
+
 TEST_HARNESS_MAIN
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/toeplitz.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/toeplitz.c
@@ -213,7 +213,7 @@
 }
 
 /* A single TPACKET_V3 block can hold multiple frames */
-static void recv_block(struct ring_state *ring)
+static bool recv_block(struct ring_state *ring)
 {
 	struct tpacket_block_desc *block;
 	char *frame;
@@ -221,7 +221,7 @@
 
 	block = (void *)(ring->mmap + ring->idx * ring_block_sz);
 	if (!(block->hdr.bh1.block_status & TP_STATUS_USER))
-		return;
+		return false;
 
 	frame = (char *)block;
 	frame += block->hdr.bh1.offset_to_first_pkt;
@@ -233,6 +233,8 @@
 
 	block->hdr.bh1.block_status = TP_STATUS_KERNEL;
 	ring->idx = (ring->idx + 1) % ring_block_nr;
+
+	return true;
 }
 
 /* simple test: sleep once unconditionally and then process all rings */
@@ -243,7 +245,7 @@
 	usleep(1000 * cfg_timeout_msec);
 
 	for (i = 0; i < num_cpus; i++)
-		recv_block(&rings[i]);
+		do {} while (recv_block(&rings[i]));
 
 	fprintf(stderr, "count: pass=%u nohash=%u fail=%u\n",
 		frames_received - frames_nohash - frames_error,
@@ -255,12 +257,12 @@
 	struct tpacket_req3 req3 = {0};
 	void *ring;
 
-	req3.tp_retire_blk_tov = cfg_timeout_msec;
+	req3.tp_retire_blk_tov = cfg_timeout_msec / 8;
 	req3.tp_feature_req_word = TP_FT_REQ_FILL_RXHASH;
 
 	req3.tp_frame_size = 2048;
 	req3.tp_frame_nr = 1 << 10;
-	req3.tp_block_nr = 2;
+	req3.tp_block_nr = 16;
 
 	req3.tp_block_size = req3.tp_frame_size * req3.tp_frame_nr;
 	req3.tp_block_size /= req3.tp_block_nr;
@@ -498,7 +500,7 @@
 	bool have_toeplitz = false;
 	int index, c;
 
-	while ((c = getopt_long(argc, argv, "46C:d:i:k:r:stT:u:v", long_options, &index)) != -1) {
+	while ((c = getopt_long(argc, argv, "46C:d:i:k:r:stT:uv", long_options, &index)) != -1) {
 		switch (c) {
 		case '4':
 			cfg_family = AF_INET;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/toeplitz.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/toeplitz.sh
@@ -32,7 +32,7 @@
 # This is determined by reading the RSS indirection table using ethtool.
 get_rss_cfg_num_rxqs() {
 	echo $(ethtool -x "${DEV}" |
-		egrep [[:space:]]+[0-9]+:[[:space:]]+ |
+		grep -E [[:space:]]+[0-9]+:[[:space:]]+ |
 		cut -d: -f2- |
 		awk '{$1=$1};1' |
 		tr ' ' '\n' |
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgro.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgro.sh
@@ -3,6 +3,8 @@
 #
 # Run a series of udpgro functional tests.
 
+source net_helper.sh
+
 readonly PEER_NS="ns-peer-$(mktemp -u XXXXXX)"
 
 # set global exit status, but never reset nonzero one.
@@ -34,7 +36,7 @@
 	ip -netns "${PEER_NS}" addr add dev veth1 192.168.1.1/24
 	ip -netns "${PEER_NS}" addr add dev veth1 2001:db8::1/64 nodad
 	ip -netns "${PEER_NS}" link set dev veth1 up
-	ip -n "${PEER_NS}" link set veth1 xdp object ../bpf/xdp_dummy.o section xdp_dummy
+	ip -n "${PEER_NS}" link set veth1 xdp object ../bpf/xdp_dummy.o section xdp
 }
 
 run_one() {
@@ -49,8 +51,7 @@
 		echo "ok" || \
 		echo "failed" &
 
-	# Hack: let bg programs complete the startup
-	sleep 0.1
+	wait_local_port_listen ${PEER_NS} 8000 udp
 	./udpgso_bench_tx ${tx_args}
 	ret=$?
 	wait $(jobs -p)
@@ -95,7 +96,7 @@
 		echo "ok" || \
 		echo "failed"&
 
-	sleep 0.1
+	wait_local_port_listen "${PEER_NS}" 8000 udp
 	./udpgso_bench_tx ${tx_args}
 	ret=$?
 	kill -INT $pid
@@ -116,11 +117,9 @@
 		echo "ok" || \
 		echo "failed" &
 
-	# Hack: let bg programs complete the startup
-	sleep 0.1
+	wait_local_port_listen "${PEER_NS}" 12345 udp
 	./udpgso_bench_tx ${tx_args} -p 12345
-	sleep 0.1
-	# first UDP GSO socket should be closed at this point
+	wait_local_port_listen "${PEER_NS}" 8000 udp
 	./udpgso_bench_tx ${tx_args}
 	ret=$?
 	wait $(jobs -p)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgro_bench.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgro_bench.sh
@@ -3,6 +3,8 @@
 #
 # Run a series of udpgro benchmarks
 
+source net_helper.sh
+
 readonly PEER_NS="ns-peer-$(mktemp -u XXXXXX)"
 
 cleanup() {
@@ -34,12 +36,11 @@
 	ip -netns "${PEER_NS}" addr add dev veth1 2001:db8::1/64 nodad
 	ip -netns "${PEER_NS}" link set dev veth1 up
 
-	ip -n "${PEER_NS}" link set veth1 xdp object ../bpf/xdp_dummy.o section xdp_dummy
+	ip -n "${PEER_NS}" link set veth1 xdp object ../bpf/xdp_dummy.o section xdp
 	ip netns exec "${PEER_NS}" ./udpgso_bench_rx ${rx_args} -r &
 	ip netns exec "${PEER_NS}" ./udpgso_bench_rx -t ${rx_args} -r &
 
-	# Hack: let bg programs complete the startup
-	sleep 0.1
+	wait_local_port_listen "${PEER_NS}" 8000 udp
 	./udpgso_bench_tx ${tx_args}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgro_fwd.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgro_fwd.sh
@@ -36,6 +36,10 @@
 	for ns in $NS_SRC $NS_DST; do
 		ip netns add $ns
 		ip -n $ns link set dev lo up
+
+		# disable route solicitations to decrease 'noise' traffic
+		ip netns exec $ns sysctl -qw net.ipv6.conf.default.router_solicitations=0
+		ip netns exec $ns sysctl -qw net.ipv6.conf.all.router_solicitations=0
 	done
 
 	ip link add name veth$SRC type veth peer name veth$DST
@@ -46,7 +50,7 @@
 		ip -n $BASE$ns addr add dev veth$ns $BM_NET_V4$ns/24
 		ip -n $BASE$ns addr add dev veth$ns $BM_NET_V6$ns/64 nodad
 	done
-	ip -n $NS_DST link set veth$DST xdp object ../bpf/xdp_dummy.o section xdp_dummy 2>/dev/null
+	ip -n $NS_DST link set veth$DST xdp object ../bpf/xdp_dummy.o section xdp 2>/dev/null
 }
 
 create_vxlan_endpoint() {
@@ -77,6 +81,12 @@
 		create_vxlan_endpoint $BASE$ns veth$ns $BM_NET_V6$((3 - $ns)) vxlan6$ns 6
 		ip -n $BASE$ns addr add dev vxlan6$ns $OL_NET_V6$ns/24 nodad
 	done
+
+	# preload neighbur cache, do avoid some noisy traffic
+	local addr_dst=$(ip -j -n $BASE$DST link show dev vxlan6$DST  |jq -r '.[]["address"]')
+	local addr_src=$(ip -j -n $BASE$SRC link show dev vxlan6$SRC  |jq -r '.[]["address"]')
+	ip -n $BASE$DST neigh add dev vxlan6$DST lladdr $addr_src $OL_NET_V6$SRC
+	ip -n $BASE$SRC neigh add dev vxlan6$SRC lladdr $addr_dst $OL_NET_V6$DST
 }
 
 is_ipv6() {
@@ -116,7 +126,7 @@
 	# not enable GRO
 	ip netns exec $NS_DST $ipt -A INPUT -p udp --dport 4789
 	ip netns exec $NS_DST $ipt -A INPUT -p udp --dport 8000
-	ip netns exec $NS_DST ./udpgso_bench_rx -C 1000 -R 10 -n 10 -l 1300 $rx_args &
+	ip netns exec $NS_DST ./udpgso_bench_rx -C 2000 -R 100 -n 10 -l 1300 $rx_args &
 	local spid=$!
 	sleep 0.1
 	ip netns exec $NS_SRC ./udpgso_bench_tx $family -M 1 -s 13000 -S 1300 -D $dst
@@ -132,7 +142,7 @@
 	local rcv=`ip netns exec $NS_DST $ipt"-save" -c | grep 'dport 8000' | \
 							  sed -e 's/\[//' -e 's/:.*//'`
 	if [ $rcv != $pkts ]; then
-		echo " fail - received $rvs packets, expected $pkts"
+		echo " fail - received $rcv packets, expected $pkts"
 		ret=1
 		return
 	fi
@@ -165,7 +175,7 @@
 	# bind the sender and the receiver to different CPUs to try
 	# get reproducible results
 	ip netns exec $NS_DST bash -c "echo 2 > /sys/class/net/veth$DST/queues/rx-0/rps_cpus"
-	ip netns exec $NS_DST taskset 0x2 ./udpgso_bench_rx -C 1000 -R 10  &
+	ip netns exec $NS_DST taskset 0x2 ./udpgso_bench_rx -C 2000 -R 100  &
 	local spid=$!
 	sleep 0.1
 	ip netns exec $NS_SRC taskset 0x1 ./udpgso_bench_tx $family -l 3 -S 1300 -D $dst
@@ -185,6 +195,7 @@
 	IPT=iptables
 	SUFFIX=24
 	VXDEV=vxlan
+	PING=ping
 
 	if [ $family = 6 ]; then
 		BM_NET=$BM_NET_V6
@@ -192,6 +203,8 @@
 		SUFFIX="64 nodad"
 		VXDEV=vxlan6
 		IPT=ip6tables
+		# Use ping6 on systems where ping doesn't handle IPv6
+		ping -w 1 -c 1 ::1 > /dev/null 2>&1 || PING="ping6"
 	fi
 
 	echo "IPv$family"
@@ -225,7 +238,7 @@
 
 	create_vxlan_pair
 	ip netns exec $NS_DST ethtool -K veth$DST rx-gro-list on
-	run_test "GRO frag list over UDP tunnel" $OL_NET$DST 1 1
+	run_test "GRO frag list over UDP tunnel" $OL_NET$DST 10 10
 	cleanup
 
 	# use NAT to circumvent GRO FWD check
@@ -237,14 +250,8 @@
 
 	# load arp cache before running the test to reduce the amount of
 	# stray traffic on top of the UDP tunnel
-	ip netns exec $NS_SRC ping -q -c 1 $OL_NET$DST_NAT >/dev/null
-	run_test "GRO fwd over UDP tunnel" $OL_NET$DST_NAT 1 1 $OL_NET$DST
-	cleanup
-
-	create_vxlan_pair
-	run_bench "UDP tunnel fwd perf" $OL_NET$DST
-	ip netns exec $NS_DST ethtool -K veth$DST rx-udp-gro-forwarding on
-	run_bench "UDP tunnel GRO fwd perf" $OL_NET$DST
+	ip netns exec $NS_SRC $PING -q -c 1 $OL_NET$DST_NAT >/dev/null
+	run_test "GRO fwd over UDP tunnel" $OL_NET$DST_NAT 10 10 $OL_NET$DST
 	cleanup
 done
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgso.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgso.c
@@ -34,7 +34,7 @@
 #endif
 
 #ifndef UDP_MAX_SEGMENTS
-#define UDP_MAX_SEGMENTS	(1 << 6UL)
+#define UDP_MAX_SEGMENTS	(1 << 7UL)
 #endif
 
 #define CONST_MTU_TEST	1500
@@ -95,6 +95,19 @@
 		.r_num_mss = 1,
 	},
 	{
+		/* datalen <= MSS < gso_len: will fall back to no GSO */
+		.tlen = CONST_MSS_V4,
+		.gso_len = CONST_MSS_V4 + 1,
+		.r_num_mss = 0,
+		.r_len_last = CONST_MSS_V4,
+	},
+	{
+		/* MSS < datalen < gso_len: fail */
+		.tlen = CONST_MSS_V4 + 1,
+		.gso_len = CONST_MSS_V4 + 2,
+		.tfail = true,
+	},
+	{
 		/* send a single MSS + 1B */
 		.tlen = CONST_MSS_V4 + 1,
 		.gso_len = CONST_MSS_V4,
@@ -156,13 +169,13 @@
 	},
 	{
 		/* send max number of min sized segments */
-		.tlen = UDP_MAX_SEGMENTS - CONST_HDRLEN_V4,
+		.tlen = UDP_MAX_SEGMENTS,
 		.gso_len = 1,
-		.r_num_mss = UDP_MAX_SEGMENTS - CONST_HDRLEN_V4,
+		.r_num_mss = UDP_MAX_SEGMENTS,
 	},
 	{
 		/* send max number + 1 of min sized segments: fail */
-		.tlen = UDP_MAX_SEGMENTS - CONST_HDRLEN_V4 + 1,
+		.tlen = UDP_MAX_SEGMENTS + 1,
 		.gso_len = 1,
 		.tfail = true,
 	},
@@ -198,6 +211,19 @@
 		.r_num_mss = 1,
 	},
 	{
+		/* datalen <= MSS < gso_len: will fall back to no GSO */
+		.tlen = CONST_MSS_V6,
+		.gso_len = CONST_MSS_V6 + 1,
+		.r_num_mss = 0,
+		.r_len_last = CONST_MSS_V6,
+	},
+	{
+		/* MSS < datalen < gso_len: fail */
+		.tlen = CONST_MSS_V6 + 1,
+		.gso_len = CONST_MSS_V6 + 2,
+		.tfail = true
+	},
+	{
 		/* send a single MSS + 1B */
 		.tlen = CONST_MSS_V6 + 1,
 		.gso_len = CONST_MSS_V6,
@@ -259,13 +285,13 @@
 	},
 	{
 		/* send max number of min sized segments */
-		.tlen = UDP_MAX_SEGMENTS - CONST_HDRLEN_V6,
+		.tlen = UDP_MAX_SEGMENTS,
 		.gso_len = 1,
-		.r_num_mss = UDP_MAX_SEGMENTS - CONST_HDRLEN_V6,
+		.r_num_mss = UDP_MAX_SEGMENTS,
 	},
 	{
 		/* send max number + 1 of min sized segments: fail */
-		.tlen = UDP_MAX_SEGMENTS - CONST_HDRLEN_V6 + 1,
+		.tlen = UDP_MAX_SEGMENTS + 1,
 		.gso_len = 1,
 		.tfail = true,
 	},
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgso_bench.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgso_bench.sh
@@ -7,6 +7,7 @@
 readonly YELLOW='\033[0;33m'
 readonly RED='\033[0;31m'
 readonly NC='\033[0m' # No Color
+readonly TESTPORT=8000
 
 readonly KSFT_PASS=0
 readonly KSFT_FAIL=1
@@ -56,11 +57,26 @@
 
 run_one() {
 	local -r args=$@
+	local nr_socks=0
+	local i=0
+	local -r timeout=10
+
+	./udpgso_bench_rx -p "$TESTPORT" &
+	./udpgso_bench_rx -p "$TESTPORT" -t &
+
+	# Wait for the above test program to get ready to receive connections.
+	while [ "$i" -lt "$timeout" ]; do
+		nr_socks="$(ss -lnHi | grep -c "\*:${TESTPORT}")"
+		[ "$nr_socks" -eq 2 ] && break
+		i=$((i + 1))
+		sleep 1
+	done
+	if [ "$nr_socks" -ne 2 ]; then
+		echo "timed out while waiting for udpgso_bench_rx"
+		exit 1
+	fi
 
-	./udpgso_bench_rx &
-	./udpgso_bench_rx -t &
-
-	./udpgso_bench_tx ${args}
+	./udpgso_bench_tx -p "$TESTPORT" ${args}
 }
 
 run_in_netns() {
@@ -120,7 +136,7 @@
 	run_udp "${ipv4_args}"
 
 	echo "ipv6"
-	run_tcp "${ipv4_args}"
+	run_tcp "${ipv6_args}"
 	run_udp "${ipv6_args}"
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgso_bench_rx.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgso_bench_rx.c
@@ -214,11 +214,10 @@
 
 static int recv_msg(int fd, char *buf, int len, int *gso_size)
 {
-	char control[CMSG_SPACE(sizeof(uint16_t))] = {0};
+	char control[CMSG_SPACE(sizeof(int))] = {0};
 	struct msghdr msg = {0};
 	struct iovec iov = {0};
 	struct cmsghdr *cmsg;
-	uint16_t *gsosizeptr;
 	int ret;
 
 	iov.iov_base = buf;
@@ -237,8 +236,7 @@
 		     cmsg = CMSG_NXTHDR(&msg, cmsg)) {
 			if (cmsg->cmsg_level == SOL_UDP
 			    && cmsg->cmsg_type == UDP_GRO) {
-				gsosizeptr = (uint16_t *) CMSG_DATA(cmsg);
-				*gso_size = *gsosizeptr;
+				*gso_size = *(int *)CMSG_DATA(cmsg);
 				break;
 			}
 		}
@@ -250,7 +248,7 @@
 static void do_flush_udp(int fd)
 {
 	static char rbuf[ETH_MAX_MTU];
-	int ret, len, gso_size, budget = 256;
+	int ret, len, gso_size = 0, budget = 256;
 
 	len = cfg_read_all ? sizeof(rbuf) : 0;
 	while (budget--) {
@@ -293,19 +291,17 @@
 
 static void parse_opts(int argc, char **argv)
 {
+	const char *bind_addr = NULL;
 	int c;
 
-	/* bind to any by default */
-	setup_sockaddr(PF_INET6, "::", &cfg_bind_addr);
 	while ((c = getopt(argc, argv, "4b:C:Gl:n:p:rR:S:tv")) != -1) {
 		switch (c) {
 		case '4':
 			cfg_family = PF_INET;
 			cfg_alen = sizeof(struct sockaddr_in);
-			setup_sockaddr(PF_INET, "0.0.0.0", &cfg_bind_addr);
 			break;
 		case 'b':
-			setup_sockaddr(cfg_family, optarg, &cfg_bind_addr);
+			bind_addr = optarg;
 			break;
 		case 'C':
 			cfg_connect_timeout_ms = strtoul(optarg, NULL, 0);
@@ -338,9 +334,16 @@
 			cfg_verify = true;
 			cfg_read_all = true;
 			break;
+		default:
+			exit(1);
 		}
 	}
 
+	if (!bind_addr)
+		bind_addr = cfg_family == PF_INET6 ? "::" : "0.0.0.0";
+
+	setup_sockaddr(cfg_family, bind_addr, &cfg_bind_addr);
+
 	if (optind != argc)
 		usage(argv[0]);
 
@@ -372,7 +375,7 @@
 			do_flush_udp(fd);
 
 		tnow = gettimeofday_ms();
-		if (tnow > treport) {
+		if (!cfg_expected_pkt_nr && tnow > treport) {
 			if (packets)
 				fprintf(stderr,
 					"%s rx: %6lu MB/s %8lu calls/s\n",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/udpgso_bench_tx.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/udpgso_bench_tx.c
@@ -62,6 +62,7 @@
 static int	cfg_port	= 8000;
 static int	cfg_runtime_ms	= -1;
 static bool	cfg_poll;
+static int	cfg_poll_loop_timeout_ms = 2000;
 static bool	cfg_segment;
 static bool	cfg_sendmmsg;
 static bool	cfg_tcp;
@@ -235,16 +236,17 @@
 	}
 }
 
-static void flush_errqueue(int fd, const bool do_poll)
+static void flush_errqueue(int fd, const bool do_poll,
+			   unsigned long poll_timeout, const bool poll_err)
 {
 	if (do_poll) {
 		struct pollfd fds = {0};
 		int ret;
 
 		fds.fd = fd;
-		ret = poll(&fds, 1, 500);
+		ret = poll(&fds, 1, poll_timeout);
 		if (ret == 0) {
-			if (cfg_verbose)
+			if ((cfg_verbose) && (poll_err))
 				fprintf(stderr, "poll timeout\n");
 		} else if (ret < 0) {
 			error(1, errno, "poll");
@@ -254,6 +256,20 @@
 	flush_errqueue_recv(fd);
 }
 
+static void flush_errqueue_retry(int fd, unsigned long num_sends)
+{
+	unsigned long tnow, tstop;
+	bool first_try = true;
+
+	tnow = gettimeofday_ms();
+	tstop = tnow + cfg_poll_loop_timeout_ms;
+	do {
+		flush_errqueue(fd, true, tstop - tnow, first_try);
+		first_try = false;
+		tnow = gettimeofday_ms();
+	} while ((stat_zcopies != num_sends) && (tnow < tstop));
+}
+
 static int send_tcp(int fd, char *data)
 {
 	int ret, done = 0, count = 0;
@@ -413,16 +429,18 @@
 
 static void usage(const char *filepath)
 {
-	error(1, 0, "Usage: %s [-46acmHPtTuvz] [-C cpu] [-D dst ip] [-l secs] [-M messagenr] [-p port] [-s sendsize] [-S gsosize]",
+	error(1, 0, "Usage: %s [-46acmHPtTuvz] [-C cpu] [-D dst ip] [-l secs] "
+		    "[-L secs] [-M messagenr] [-p port] [-s sendsize] [-S gsosize]",
 		    filepath);
 }
 
 static void parse_opts(int argc, char **argv)
 {
+	const char *bind_addr = NULL;
 	int max_len, hdrlen;
 	int c;
 
-	while ((c = getopt(argc, argv, "46acC:D:Hl:mM:p:s:PS:tTuvz")) != -1) {
+	while ((c = getopt(argc, argv, "46acC:D:Hl:L:mM:p:s:PS:tTuvz")) != -1) {
 		switch (c) {
 		case '4':
 			if (cfg_family != PF_UNSPEC)
@@ -446,11 +464,14 @@
 			cfg_cpu = strtol(optarg, NULL, 0);
 			break;
 		case 'D':
-			setup_sockaddr(cfg_family, optarg, &cfg_dst_addr);
+			bind_addr = optarg;
 			break;
 		case 'l':
 			cfg_runtime_ms = strtoul(optarg, NULL, 10) * 1000;
 			break;
+		case 'L':
+			cfg_poll_loop_timeout_ms = strtoul(optarg, NULL, 10) * 1000;
+			break;
 		case 'm':
 			cfg_sendmmsg = true;
 			break;
@@ -489,9 +510,16 @@
 		case 'z':
 			cfg_zerocopy = true;
 			break;
+		default:
+			exit(1);
 		}
 	}
 
+	if (!bind_addr)
+		bind_addr = cfg_family == PF_INET6 ? "::" : "0.0.0.0";
+
+	setup_sockaddr(cfg_family, bind_addr, &cfg_dst_addr);
+
 	if (optind != argc)
 		usage(argv[0]);
 
@@ -671,7 +699,7 @@
 			num_sends += send_udp(fd, buf[i]);
 		num_msgs++;
 		if ((cfg_zerocopy && ((num_msgs & 0xF) == 0)) || cfg_tx_tstamp)
-			flush_errqueue(fd, cfg_poll);
+			flush_errqueue(fd, cfg_poll, 500, true);
 
 		if (cfg_msg_nr && num_msgs >= cfg_msg_nr)
 			break;
@@ -690,7 +718,7 @@
 	} while (!interrupted && (cfg_runtime_ms == -1 || tnow < tstop));
 
 	if (cfg_zerocopy || cfg_tx_tstamp)
-		flush_errqueue(fd, true);
+		flush_errqueue_retry(fd, num_sends);
 
 	if (close(fd))
 		error(1, errno, "close");
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/veth.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/veth.sh
@@ -289,14 +289,14 @@
 	ip netns exec $NS_SRC ethtool -L veth$SRC rx 1 tx 2 2>/dev/null
 	printf "%-60s" "bad setting: XDP with RX nr less than TX"
 	ip -n $NS_DST link set dev veth$DST xdp object ../bpf/xdp_dummy.o \
-		section xdp_dummy 2>/dev/null &&\
+		section xdp 2>/dev/null &&\
 		echo "fail - set operation successful ?!?" || echo " ok "
 
 	# the following tests will run with multiple channels active
 	ip netns exec $NS_SRC ethtool -L veth$SRC rx 2
 	ip netns exec $NS_DST ethtool -L veth$DST rx 2
 	ip -n $NS_DST link set dev veth$DST xdp object ../bpf/xdp_dummy.o \
-		section xdp_dummy 2>/dev/null
+		section xdp 2>/dev/null
 	printf "%-60s" "bad setting: reducing RX nr below peer TX with XDP set"
 	ip netns exec $NS_DST ethtool -L veth$DST rx 1 2>/dev/null &&\
 		echo "fail - set operation successful ?!?" || echo " ok "
@@ -311,7 +311,7 @@
 	chk_channels "setting invalid channels nr" $DST 2 2
 fi
 
-ip -n $NS_DST link set dev veth$DST xdp object ../bpf/xdp_dummy.o section xdp_dummy 2>/dev/null
+ip -n $NS_DST link set dev veth$DST xdp object ../bpf/xdp_dummy.o section xdp 2>/dev/null
 chk_gro_flag "with xdp attached - gro flag" $DST on
 chk_gro_flag "        - peer gro flag" $SRC off
 chk_tso_flag "        - tso flag" $SRC off
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/net/vrf-xfrm-tests.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/net/vrf-xfrm-tests.sh
@@ -264,60 +264,60 @@
 	ip -netns host1 xfrm state add src ${HOST1_4} dst ${HOST2_4} \
 	    proto esp spi ${SPI_1} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_1} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_1} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_1} 96 \
+	    enc 'cbc(aes)' ${ENC_1} \
 	    sel src ${h1_4} dst ${h2_4} ${devarg}
 
 	ip -netns host2 xfrm state add src ${HOST1_4} dst ${HOST2_4} \
 	    proto esp spi ${SPI_1} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_1} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_1} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_1} 96 \
+	    enc 'cbc(aes)' ${ENC_1} \
 	    sel src ${h1_4} dst ${h2_4}
 
 
 	ip -netns host1 xfrm state add src ${HOST2_4} dst ${HOST1_4} \
 	    proto esp spi ${SPI_2} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_2} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_2} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_2} 96 \
+	    enc 'cbc(aes)' ${ENC_2} \
 	    sel src ${h2_4} dst ${h1_4} ${devarg}
 
 	ip -netns host2 xfrm state add src ${HOST2_4} dst ${HOST1_4} \
 	    proto esp spi ${SPI_2} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_2} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_2} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_2} 96 \
+	    enc 'cbc(aes)' ${ENC_2} \
 	    sel src ${h2_4} dst ${h1_4}
 
 
 	ip -6 -netns host1 xfrm state add src ${HOST1_6} dst ${HOST2_6} \
 	    proto esp spi ${SPI_1} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_1} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_1} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_1} 96 \
+	    enc 'cbc(aes)' ${ENC_1} \
 	    sel src ${h1_6} dst ${h2_6} ${devarg}
 
 	ip -6 -netns host2 xfrm state add src ${HOST1_6} dst ${HOST2_6} \
 	    proto esp spi ${SPI_1} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_1} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_1} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_1} 96 \
+	    enc 'cbc(aes)' ${ENC_1} \
 	    sel src ${h1_6} dst ${h2_6}
 
 
 	ip -6 -netns host1 xfrm state add src ${HOST2_6} dst ${HOST1_6} \
 	    proto esp spi ${SPI_2} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_2} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_2} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_2} 96 \
+	    enc 'cbc(aes)' ${ENC_2} \
 	    sel src ${h2_6} dst ${h1_6} ${devarg}
 
 	ip -6 -netns host2 xfrm state add src ${HOST2_6} dst ${HOST1_6} \
 	    proto esp spi ${SPI_2} reqid 0 mode tunnel \
 	    replay-window 4 replay-oseq 0x4 \
-	    auth-trunc 'hmac(md5)' ${AUTH_2} 96 \
-	    enc 'cbc(des3_ede)' ${ENC_2} \
+	    auth-trunc 'hmac(sha1)' ${AUTH_2} 96 \
+	    enc 'cbc(aes)' ${ENC_2} \
 	    sel src ${h2_6} dst ${h1_6}
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/Makefile
@@ -5,7 +5,8 @@
 	conntrack_icmp_related.sh nft_flowtable.sh ipvs.sh \
 	nft_concat_range.sh nft_conntrack_helper.sh \
 	nft_queue.sh nft_meta.sh nf_nat_edemux.sh \
-	ipip-conntrack-mtu.sh conntrack_tcp_unreplied.sh
+	ipip-conntrack-mtu.sh conntrack_tcp_unreplied.sh \
+	conntrack_vrf.sh
 
 LDLIBS = -lmnl
 TEST_GEN_FILES =  nf-queue
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/conntrack_icmp_related.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/conntrack_icmp_related.sh
@@ -35,6 +35,8 @@
 	for i in 1 2;do ip netns del nsrouter$i;done
 }
 
+trap cleanup EXIT
+
 ipv4() {
     echo -n 192.168.$1.2
 }
@@ -146,11 +148,17 @@
 table inet filter {
 	counter unknown { }
 	counter related { }
+	counter redir4 { }
+	counter redir6 { }
 	chain input {
 		type filter hook input priority 0; policy accept;
-		meta l4proto { icmp, icmpv6 } ct state established,untracked accept
 
+		icmp type "redirect" ct state "related" counter name "redir4" accept
+		icmpv6 type "nd-redirect" ct state "related" counter name "redir6" accept
+
+		meta l4proto { icmp, icmpv6 } ct state established,untracked accept
 		meta l4proto { icmp, icmpv6 } ct state "related" counter name "related" accept
+
 		counter name "unknown" drop
 	}
 }
@@ -279,5 +287,29 @@
 	echo "ERROR: icmp error RELATED state test has failed"
 fi
 
-cleanup
+# add 'bad' route,  expect icmp REDIRECT to be generated
+ip netns exec nsclient1 ip route add 192.168.1.42 via 192.168.1.1
+ip netns exec nsclient1 ip route add dead:1::42 via dead:1::1
+
+ip netns exec "nsclient1" ping -q -c 2 192.168.1.42 > /dev/null
+
+expect="packets 1 bytes 112"
+check_counter nsclient1 "redir4" "$expect"
+if [ $? -ne 0 ];then
+	ret=1
+fi
+
+ip netns exec "nsclient1" ping -c 1 dead:1::42 > /dev/null
+expect="packets 1 bytes 192"
+check_counter nsclient1 "redir6" "$expect"
+if [ $? -ne 0 ];then
+	ret=1
+fi
+
+if [ $ret -eq 0 ];then
+	echo "PASS: icmp redirects had RELATED state"
+else
+	echo "ERROR: icmp redirect RELATED state test has failed"
+fi
+
 exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/conntrack_vrf.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/conntrack_vrf.sh
@@ -0,0 +1,241 @@
+#!/bin/sh
+
+# This script demonstrates interaction of conntrack and vrf.
+# The vrf driver calls the netfilter hooks again, with oif/iif
+# pointing at the VRF device.
+#
+# For ingress, this means first iteration has iifname of lower/real
+# device.  In this script, thats veth0.
+# Second iteration is iifname set to vrf device, tvrf in this script.
+#
+# For egress, this is reversed: first iteration has the vrf device,
+# second iteration is done with the lower/real/veth0 device.
+#
+# test_ct_zone_in demonstrates unexpected change of nftables
+# behavior # caused by commit 09e856d54bda5f28 "vrf: Reset skb conntrack
+# connection on VRF rcv"
+#
+# It was possible to assign conntrack zone to a packet (or mark it for
+# `notracking`) in the prerouting chain before conntrack, based on real iif.
+#
+# After the change, the zone assignment is lost and the zone is assigned based
+# on the VRF master interface (in case such a rule exists).
+# assignment is lost. Instead, assignment based on the `iif` matching
+# Thus it is impossible to distinguish packets based on the original
+# interface.
+#
+# test_masquerade_vrf and test_masquerade_veth0 demonstrate the problem
+# that was supposed to be fixed by the commit mentioned above to make sure
+# that any fix to test case 1 won't break masquerade again.
+
+ksft_skip=4
+
+IP0=172.30.30.1
+IP1=172.30.30.2
+PFXL=30
+ret=0
+
+sfx=$(mktemp -u "XXXXXXXX")
+ns0="ns0-$sfx"
+ns1="ns1-$sfx"
+
+cleanup()
+{
+	ip netns pids $ns0 | xargs kill 2>/dev/null
+	ip netns pids $ns1 | xargs kill 2>/dev/null
+
+	ip netns del $ns0 $ns1
+}
+
+nft --version > /dev/null 2>&1
+if [ $? -ne 0 ];then
+	echo "SKIP: Could not run test without nft tool"
+	exit $ksft_skip
+fi
+
+ip -Version > /dev/null 2>&1
+if [ $? -ne 0 ];then
+	echo "SKIP: Could not run test without ip tool"
+	exit $ksft_skip
+fi
+
+ip netns add "$ns0"
+if [ $? -ne 0 ];then
+	echo "SKIP: Could not create net namespace $ns0"
+	exit $ksft_skip
+fi
+ip netns add "$ns1"
+
+trap cleanup EXIT
+
+ip netns exec $ns0 sysctl -q -w net.ipv4.conf.default.rp_filter=0
+ip netns exec $ns0 sysctl -q -w net.ipv4.conf.all.rp_filter=0
+ip netns exec $ns0 sysctl -q -w net.ipv4.conf.all.rp_filter=0
+
+ip link add veth0 netns "$ns0" type veth peer name veth0 netns "$ns1" > /dev/null 2>&1
+if [ $? -ne 0 ];then
+	echo "SKIP: Could not add veth device"
+	exit $ksft_skip
+fi
+
+ip -net $ns0 li add tvrf type vrf table 9876
+if [ $? -ne 0 ];then
+	echo "SKIP: Could not add vrf device"
+	exit $ksft_skip
+fi
+
+ip -net $ns0 li set lo up
+
+ip -net $ns0 li set veth0 master tvrf
+ip -net $ns0 li set tvrf up
+ip -net $ns0 li set veth0 up
+ip -net $ns1 li set veth0 up
+
+ip -net $ns0 addr add $IP0/$PFXL dev veth0
+ip -net $ns1 addr add $IP1/$PFXL dev veth0
+
+ip netns exec $ns1 iperf3 -s > /dev/null 2>&1&
+if [ $? -ne 0 ];then
+	echo "SKIP: Could not start iperf3"
+	exit $ksft_skip
+fi
+
+# test vrf ingress handling.
+# The incoming connection should be placed in conntrack zone 1,
+# as decided by the first iteration of the ruleset.
+test_ct_zone_in()
+{
+ip netns exec $ns0 nft -f - <<EOF
+table testct {
+	chain rawpre {
+		type filter hook prerouting priority raw;
+
+		iif { veth0, tvrf } counter meta nftrace set 1
+		iif veth0 counter ct zone set 1 counter return
+		iif tvrf counter ct zone set 2 counter return
+		ip protocol icmp counter
+		notrack counter
+	}
+
+	chain rawout {
+		type filter hook output priority raw;
+
+		oif veth0 counter ct zone set 1 counter return
+		oif tvrf counter ct zone set 2 counter return
+		notrack counter
+	}
+}
+EOF
+	ip netns exec $ns1 ping -W 1 -c 1 -I veth0 $IP0 > /dev/null
+
+	# should be in zone 1, not zone 2
+	count=$(ip netns exec $ns0 conntrack -L -s $IP1 -d $IP0 -p icmp --zone 1 2>/dev/null | wc -l)
+	if [ $count -eq 1 ]; then
+		echo "PASS: entry found in conntrack zone 1"
+	else
+		echo "FAIL: entry not found in conntrack zone 1"
+		count=$(ip netns exec $ns0 conntrack -L -s $IP1 -d $IP0 -p icmp --zone 2 2> /dev/null | wc -l)
+		if [ $count -eq 1 ]; then
+			echo "FAIL: entry found in zone 2 instead"
+		else
+			echo "FAIL: entry not in zone 1 or 2, dumping table"
+			ip netns exec $ns0 conntrack -L
+			ip netns exec $ns0 nft list ruleset
+		fi
+	fi
+}
+
+# add masq rule that gets evaluated w. outif set to vrf device.
+# This tests the first iteration of the packet through conntrack,
+# oifname is the vrf device.
+test_masquerade_vrf()
+{
+	local qdisc=$1
+
+	if [ "$qdisc" != "default" ]; then
+		tc -net $ns0 qdisc add dev tvrf root $qdisc
+	fi
+
+	ip netns exec $ns0 conntrack -F 2>/dev/null
+
+ip netns exec $ns0 nft -f - <<EOF
+flush ruleset
+table ip nat {
+	chain rawout {
+		type filter hook output priority raw;
+
+		oif tvrf ct state untracked counter
+	}
+	chain postrouting2 {
+		type filter hook postrouting priority mangle;
+
+		oif tvrf ct state untracked counter
+	}
+	chain postrouting {
+		type nat hook postrouting priority 0;
+		# NB: masquerade should always be combined with 'oif(name) bla',
+		# lack of this is intentional here, we want to exercise double-snat.
+		ip saddr 172.30.30.0/30 counter masquerade random
+	}
+}
+EOF
+	ip netns exec $ns0 ip vrf exec tvrf iperf3 -t 1 -c $IP1 >/dev/null
+	if [ $? -ne 0 ]; then
+		echo "FAIL: iperf3 connect failure with masquerade + sport rewrite on vrf device"
+		ret=1
+		return
+	fi
+
+	# must also check that nat table was evaluated on second (lower device) iteration.
+	ip netns exec $ns0 nft list table ip nat |grep -q 'counter packets 2' &&
+	ip netns exec $ns0 nft list table ip nat |grep -q 'untracked counter packets [1-9]'
+	if [ $? -eq 0 ]; then
+		echo "PASS: iperf3 connect with masquerade + sport rewrite on vrf device ($qdisc qdisc)"
+	else
+		echo "FAIL: vrf rules have unexpected counter value"
+		ret=1
+	fi
+
+	if [ "$qdisc" != "default" ]; then
+		tc -net $ns0 qdisc del dev tvrf root
+	fi
+}
+
+# add masq rule that gets evaluated w. outif set to veth device.
+# This tests the 2nd iteration of the packet through conntrack,
+# oifname is the lower device (veth0 in this case).
+test_masquerade_veth()
+{
+	ip netns exec $ns0 conntrack -F 2>/dev/null
+ip netns exec $ns0 nft -f - <<EOF
+flush ruleset
+table ip nat {
+	chain postrouting {
+		type nat hook postrouting priority 0;
+		meta oif veth0 ip saddr 172.30.30.0/30 counter masquerade random
+	}
+}
+EOF
+	ip netns exec $ns0 ip vrf exec tvrf iperf3 -t 1 -c $IP1 > /dev/null
+	if [ $? -ne 0 ]; then
+		echo "FAIL: iperf3 connect failure with masquerade + sport rewrite on veth device"
+		ret=1
+		return
+	fi
+
+	# must also check that nat table was evaluated on second (lower device) iteration.
+	ip netns exec $ns0 nft list table ip nat |grep -q 'counter packets 2'
+	if [ $? -eq 0 ]; then
+		echo "PASS: iperf3 connect with masquerade + sport rewrite on veth device"
+	else
+		echo "FAIL: vrf masq rule has unexpected counter value"
+		ret=1
+	fi
+}
+
+test_ct_zone_in
+test_masquerade_vrf "default"
+test_masquerade_vrf "pfifo"
+test_masquerade_veth
+
+exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/nft_concat_range.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/nft_concat_range.sh
@@ -27,11 +27,11 @@
        net_port_mac_proto_net"
 
 # Reported bugs, also described by TYPE_ variables below
-BUGS="flush_remove_add"
+BUGS="flush_remove_add reload"
 
 # List of possible paths to pktgen script from kernel tree for performance tests
 PKTGEN_SCRIPT_PATHS="
-	../../../samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh
+	../../../../samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh
 	pktgen/pktgen_bench_xmit_mode_netif_receive.sh"
 
 # Definition of set types:
@@ -337,6 +337,23 @@
 display		Add two elements, flush, re-add
 "
 
+TYPE_reload="
+display		net,mac with reload
+type_spec	ipv4_addr . ether_addr
+chain_spec	ip daddr . ether saddr
+dst		addr4
+src		mac
+start		1
+count		1
+src_delta	2000
+tools		sendip nc bash
+proto		udp
+
+race_repeat	0
+
+perf_duration	0
+"
+
 # Set template for all tests, types and rules are filled in depending on test
 set_template='
 flush ruleset
@@ -1455,6 +1472,59 @@
 	nft flush ruleset
 }
 
+# - add ranged element, check that packets match it
+# - reload the set, check packets still match
+test_bug_reload() {
+	setup veth send_"${proto}" set || return ${KSELFTEST_SKIP}
+	rstart=${start}
+
+	range_size=1
+	for i in $(seq "${start}" $((start + count))); do
+		end=$((start + range_size))
+
+		# Avoid negative or zero-sized port ranges
+		if [ $((end / 65534)) -gt $((start / 65534)) ]; then
+			start=${end}
+			end=$((end + 1))
+		fi
+		srcstart=$((start + src_delta))
+		srcend=$((end + src_delta))
+
+		add "$(format)" || return 1
+		range_size=$((range_size + 1))
+		start=$((end + range_size))
+	done
+
+	# check kernel does allocate pcpu sctrach map
+	# for reload with no elemet add/delete
+	( echo flush set inet filter test ;
+	  nft list set inet filter test ) | nft -f -
+
+	start=${rstart}
+	range_size=1
+
+	for i in $(seq "${start}" $((start + count))); do
+		end=$((start + range_size))
+
+		# Avoid negative or zero-sized port ranges
+		if [ $((end / 65534)) -gt $((start / 65534)) ]; then
+			start=${end}
+			end=$((end + 1))
+		fi
+		srcstart=$((start + src_delta))
+		srcend=$((end + src_delta))
+
+		for j in $(seq ${start} $((range_size / 2 + 1)) ${end}); do
+			send_match "${j}" $((j + src_delta)) || return 1
+		done
+
+		range_size=$((range_size + 1))
+		start=$((end + range_size))
+	done
+
+	nft flush ruleset
+}
+
 test_reported_issues() {
 	eval test_bug_"${subtest}"
 }
@@ -1513,4 +1583,4 @@
 	done
 done
 
-[ ${passed} -eq 0 ] && exit ${KSELFTEST_SKIP}
+[ ${passed} -eq 0 ] && exit ${KSELFTEST_SKIP} || exit 0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/nft_fib.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/nft_fib.sh
@@ -174,6 +174,7 @@
 ip netns exec ${nsrouter} sysctl net.ipv6.conf.all.forwarding=1 > /dev/null
 ip netns exec ${nsrouter} sysctl net.ipv4.conf.veth0.forwarding=1 > /dev/null
 ip netns exec ${nsrouter} sysctl net.ipv4.conf.veth1.forwarding=1 > /dev/null
+ip netns exec ${nsrouter} sysctl net.ipv4.conf.veth0.rp_filter=0 > /dev/null
 
 sleep 3
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/nft_flowtable.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/nft_flowtable.sh
@@ -14,6 +14,11 @@
 # nft_flowtable.sh -o8000 -l1500 -r2000
 #
 
+sfx=$(mktemp -u "XXXXXXXX")
+ns1="ns1-$sfx"
+ns2="ns2-$sfx"
+nsr1="nsr1-$sfx"
+nsr2="nsr2-$sfx"
 
 # Kselftest framework requirement - SKIP code is 4.
 ksft_skip=4
@@ -36,18 +41,17 @@
 checktool "nft --version" "run test without nft tool"
 checktool "ip -Version" "run test without ip tool"
 checktool "which nc" "run test without nc (netcat)"
-checktool "ip netns add nsr1" "create net namespace"
+checktool "ip netns add $nsr1" "create net namespace $nsr1"
 
-ip netns add ns1
-ip netns add ns2
-
-ip netns add nsr2
+ip netns add $ns1
+ip netns add $ns2
+ip netns add $nsr2
 
 cleanup() {
-	for i in 1 2; do
-		ip netns del ns$i
-		ip netns del nsr$i
-	done
+	ip netns del $ns1
+	ip netns del $ns2
+	ip netns del $nsr1
+	ip netns del $nsr2
 
 	rm -f "$ns1in" "$ns1out"
 	rm -f "$ns2in" "$ns2out"
@@ -59,22 +63,21 @@
 
 sysctl -q net.netfilter.nf_log_all_netns=1
 
-ip link add veth0 netns nsr1 type veth peer name eth0 netns ns1
-ip link add veth1 netns nsr1 type veth peer name veth0 netns nsr2
+ip link add veth0 netns $nsr1 type veth peer name eth0 netns $ns1
+ip link add veth1 netns $nsr1 type veth peer name veth0 netns $nsr2
 
-ip link add veth1 netns nsr2 type veth peer name eth0 netns ns2
+ip link add veth1 netns $nsr2 type veth peer name eth0 netns $ns2
 
 for dev in lo veth0 veth1; do
-  for i in 1 2; do
-    ip -net nsr$i link set $dev up
-  done
+    ip -net $nsr1 link set $dev up
+    ip -net $nsr2 link set $dev up
 done
 
-ip -net nsr1 addr add 10.0.1.1/24 dev veth0
-ip -net nsr1 addr add dead:1::1/64 dev veth0
+ip -net $nsr1 addr add 10.0.1.1/24 dev veth0
+ip -net $nsr1 addr add dead:1::1/64 dev veth0
 
-ip -net nsr2 addr add 10.0.2.1/24 dev veth1
-ip -net nsr2 addr add dead:2::1/64 dev veth1
+ip -net $nsr2 addr add 10.0.2.1/24 dev veth1
+ip -net $nsr2 addr add dead:2::1/64 dev veth1
 
 # set different MTUs so we need to push packets coming from ns1 (large MTU)
 # to ns2 (smaller MTU) to stack either to perform fragmentation (ip_no_pmtu_disc=1),
@@ -106,49 +109,56 @@
 	esac
 done
 
-if ! ip -net nsr1 link set veth0 mtu $omtu; then
+if ! ip -net $nsr1 link set veth0 mtu $omtu; then
 	exit 1
 fi
 
-ip -net ns1 link set eth0 mtu $omtu
+ip -net $ns1 link set eth0 mtu $omtu
 
-if ! ip -net nsr2 link set veth1 mtu $rmtu; then
+if ! ip -net $nsr2 link set veth1 mtu $rmtu; then
 	exit 1
 fi
 
-ip -net ns2 link set eth0 mtu $rmtu
+ip -net $ns2 link set eth0 mtu $rmtu
 
 # transfer-net between nsr1 and nsr2.
 # these addresses are not used for connections.
-ip -net nsr1 addr add 192.168.10.1/24 dev veth1
-ip -net nsr1 addr add fee1:2::1/64 dev veth1
+ip -net $nsr1 addr add 192.168.10.1/24 dev veth1
+ip -net $nsr1 addr add fee1:2::1/64 dev veth1
+
+ip -net $nsr2 addr add 192.168.10.2/24 dev veth0
+ip -net $nsr2 addr add fee1:2::2/64 dev veth0
+
+for i in 0 1; do
+  ip netns exec $nsr1 sysctl net.ipv4.conf.veth$i.forwarding=1 > /dev/null
+  ip netns exec $nsr2 sysctl net.ipv4.conf.veth$i.forwarding=1 > /dev/null
+done
 
-ip -net nsr2 addr add 192.168.10.2/24 dev veth0
-ip -net nsr2 addr add fee1:2::2/64 dev veth0
+for ns in $ns1 $ns2;do
+  ip -net $ns link set lo up
+  ip -net $ns link set eth0 up
 
-for i in 1 2; do
-  ip netns exec nsr$i sysctl net.ipv4.conf.veth0.forwarding=1 > /dev/null
-  ip netns exec nsr$i sysctl net.ipv4.conf.veth1.forwarding=1 > /dev/null
-
-  ip -net ns$i link set lo up
-  ip -net ns$i link set eth0 up
-  ip -net ns$i addr add 10.0.$i.99/24 dev eth0
-  ip -net ns$i route add default via 10.0.$i.1
-  ip -net ns$i addr add dead:$i::99/64 dev eth0
-  ip -net ns$i route add default via dead:$i::1
-  if ! ip netns exec ns$i sysctl net.ipv4.tcp_no_metrics_save=1 > /dev/null; then
+  if ! ip netns exec $ns sysctl net.ipv4.tcp_no_metrics_save=1 > /dev/null; then
 	echo "ERROR: Check Originator/Responder values (problem during address addition)"
 	exit 1
   fi
-
   # don't set ip DF bit for first two tests
-  ip netns exec ns$i sysctl net.ipv4.ip_no_pmtu_disc=1 > /dev/null
+  ip netns exec $ns sysctl net.ipv4.ip_no_pmtu_disc=1 > /dev/null
 done
 
-ip -net nsr1 route add default via 192.168.10.2
-ip -net nsr2 route add default via 192.168.10.1
+ip -net $ns1 addr add 10.0.1.99/24 dev eth0
+ip -net $ns2 addr add 10.0.2.99/24 dev eth0
+ip -net $ns1 route add default via 10.0.1.1
+ip -net $ns2 route add default via 10.0.2.1
+ip -net $ns1 addr add dead:1::99/64 dev eth0
+ip -net $ns2 addr add dead:2::99/64 dev eth0
+ip -net $ns1 route add default via dead:1::1
+ip -net $ns2 route add default via dead:2::1
+
+ip -net $nsr1 route add default via 192.168.10.2
+ip -net $nsr2 route add default via 192.168.10.1
 
-ip netns exec nsr1 nft -f - <<EOF
+ip netns exec $nsr1 nft -f - <<EOF
 table inet filter {
   flowtable f1 {
      hook ingress priority 0
@@ -197,18 +207,18 @@
 fi
 
 # test basic connectivity
-if ! ip netns exec ns1 ping -c 1 -q 10.0.2.99 > /dev/null; then
-  echo "ERROR: ns1 cannot reach ns2" 1>&2
+if ! ip netns exec $ns1 ping -c 1 -q 10.0.2.99 > /dev/null; then
+  echo "ERROR: $ns1 cannot reach ns2" 1>&2
   exit 1
 fi
 
-if ! ip netns exec ns2 ping -c 1 -q 10.0.1.99 > /dev/null; then
-  echo "ERROR: ns2 cannot reach ns1" 1>&2
+if ! ip netns exec $ns2 ping -c 1 -q 10.0.1.99 > /dev/null; then
+  echo "ERROR: $ns2 cannot reach $ns1" 1>&2
   exit 1
 fi
 
 if [ $ret -eq 0 ];then
-	echo "PASS: netns routing/connectivity: ns1 can reach ns2"
+	echo "PASS: netns routing/connectivity: $ns1 can reach $ns2"
 fi
 
 ns1in=$(mktemp)
@@ -312,24 +322,24 @@
 
 # First test:
 # No PMTU discovery, nsr1 is expected to fragment packets from ns1 to ns2 as needed.
-if test_tcp_forwarding ns1 ns2; then
+if test_tcp_forwarding $ns1 $ns2; then
 	echo "PASS: flow offloaded for ns1/ns2"
 else
 	echo "FAIL: flow offload for ns1/ns2:" 1>&2
-	ip netns exec nsr1 nft list ruleset
+	ip netns exec $nsr1 nft list ruleset
 	ret=1
 fi
 
 # delete default route, i.e. ns2 won't be able to reach ns1 and
 # will depend on ns1 being masqueraded in nsr1.
 # expect ns1 has nsr1 address.
-ip -net ns2 route del default via 10.0.2.1
-ip -net ns2 route del default via dead:2::1
-ip -net ns2 route add 192.168.10.1 via 10.0.2.1
+ip -net $ns2 route del default via 10.0.2.1
+ip -net $ns2 route del default via dead:2::1
+ip -net $ns2 route add 192.168.10.1 via 10.0.2.1
 
 # Second test:
 # Same, but with NAT enabled.
-ip netns exec nsr1 nft -f - <<EOF
+ip netns exec $nsr1 nft -f - <<EOF
 table ip nat {
    chain prerouting {
       type nat hook prerouting priority 0; policy accept;
@@ -343,47 +353,47 @@
 }
 EOF
 
-if test_tcp_forwarding_nat ns1 ns2; then
+if test_tcp_forwarding_nat $ns1 $ns2; then
 	echo "PASS: flow offloaded for ns1/ns2 with NAT"
 else
 	echo "FAIL: flow offload for ns1/ns2 with NAT" 1>&2
-	ip netns exec nsr1 nft list ruleset
+	ip netns exec $nsr1 nft list ruleset
 	ret=1
 fi
 
 # Third test:
 # Same as second test, but with PMTU discovery enabled.
-handle=$(ip netns exec nsr1 nft -a list table inet filter | grep something-to-grep-for | cut -d \# -f 2)
+handle=$(ip netns exec $nsr1 nft -a list table inet filter | grep something-to-grep-for | cut -d \# -f 2)
 
-if ! ip netns exec nsr1 nft delete rule inet filter forward $handle; then
+if ! ip netns exec $nsr1 nft delete rule inet filter forward $handle; then
 	echo "FAIL: Could not delete large-packet accept rule"
 	exit 1
 fi
 
-ip netns exec ns1 sysctl net.ipv4.ip_no_pmtu_disc=0 > /dev/null
-ip netns exec ns2 sysctl net.ipv4.ip_no_pmtu_disc=0 > /dev/null
+ip netns exec $ns1 sysctl net.ipv4.ip_no_pmtu_disc=0 > /dev/null
+ip netns exec $ns2 sysctl net.ipv4.ip_no_pmtu_disc=0 > /dev/null
 
-if test_tcp_forwarding_nat ns1 ns2; then
+if test_tcp_forwarding_nat $ns1 $ns2; then
 	echo "PASS: flow offloaded for ns1/ns2 with NAT and pmtu discovery"
 else
 	echo "FAIL: flow offload for ns1/ns2 with NAT and pmtu discovery" 1>&2
-	ip netns exec nsr1 nft list ruleset
+	ip netns exec $nsr1 nft list ruleset
 fi
 
 # Another test:
 # Add bridge interface br0 to Router1, with NAT enabled.
-ip -net nsr1 link add name br0 type bridge
-ip -net nsr1 addr flush dev veth0
-ip -net nsr1 link set up dev veth0
-ip -net nsr1 link set veth0 master br0
-ip -net nsr1 addr add 10.0.1.1/24 dev br0
-ip -net nsr1 addr add dead:1::1/64 dev br0
-ip -net nsr1 link set up dev br0
+ip -net $nsr1 link add name br0 type bridge
+ip -net $nsr1 addr flush dev veth0
+ip -net $nsr1 link set up dev veth0
+ip -net $nsr1 link set veth0 master br0
+ip -net $nsr1 addr add 10.0.1.1/24 dev br0
+ip -net $nsr1 addr add dead:1::1/64 dev br0
+ip -net $nsr1 link set up dev br0
 
-ip netns exec nsr1 sysctl net.ipv4.conf.br0.forwarding=1 > /dev/null
+ip netns exec $nsr1 sysctl net.ipv4.conf.br0.forwarding=1 > /dev/null
 
 # br0 with NAT enabled.
-ip netns exec nsr1 nft -f - <<EOF
+ip netns exec $nsr1 nft -f - <<EOF
 flush table ip nat
 table ip nat {
    chain prerouting {
@@ -398,59 +408,59 @@
 }
 EOF
 
-if test_tcp_forwarding_nat ns1 ns2; then
+if test_tcp_forwarding_nat $ns1 $ns2; then
 	echo "PASS: flow offloaded for ns1/ns2 with bridge NAT"
 else
 	echo "FAIL: flow offload for ns1/ns2 with bridge NAT" 1>&2
-	ip netns exec nsr1 nft list ruleset
+	ip netns exec $nsr1 nft list ruleset
 	ret=1
 fi
 
 # Another test:
 # Add bridge interface br0 to Router1, with NAT and VLAN.
-ip -net nsr1 link set veth0 nomaster
-ip -net nsr1 link set down dev veth0
-ip -net nsr1 link add link veth0 name veth0.10 type vlan id 10
-ip -net nsr1 link set up dev veth0
-ip -net nsr1 link set up dev veth0.10
-ip -net nsr1 link set veth0.10 master br0
-
-ip -net ns1 addr flush dev eth0
-ip -net ns1 link add link eth0 name eth0.10 type vlan id 10
-ip -net ns1 link set eth0 up
-ip -net ns1 link set eth0.10 up
-ip -net ns1 addr add 10.0.1.99/24 dev eth0.10
-ip -net ns1 route add default via 10.0.1.1
-ip -net ns1 addr add dead:1::99/64 dev eth0.10
+ip -net $nsr1 link set veth0 nomaster
+ip -net $nsr1 link set down dev veth0
+ip -net $nsr1 link add link veth0 name veth0.10 type vlan id 10
+ip -net $nsr1 link set up dev veth0
+ip -net $nsr1 link set up dev veth0.10
+ip -net $nsr1 link set veth0.10 master br0
+
+ip -net $ns1 addr flush dev eth0
+ip -net $ns1 link add link eth0 name eth0.10 type vlan id 10
+ip -net $ns1 link set eth0 up
+ip -net $ns1 link set eth0.10 up
+ip -net $ns1 addr add 10.0.1.99/24 dev eth0.10
+ip -net $ns1 route add default via 10.0.1.1
+ip -net $ns1 addr add dead:1::99/64 dev eth0.10
 
-if test_tcp_forwarding_nat ns1 ns2; then
+if test_tcp_forwarding_nat $ns1 $ns2; then
 	echo "PASS: flow offloaded for ns1/ns2 with bridge NAT and VLAN"
 else
 	echo "FAIL: flow offload for ns1/ns2 with bridge NAT and VLAN" 1>&2
-	ip netns exec nsr1 nft list ruleset
+	ip netns exec $nsr1 nft list ruleset
 	ret=1
 fi
 
 # restore test topology (remove bridge and VLAN)
-ip -net nsr1 link set veth0 nomaster
-ip -net nsr1 link set veth0 down
-ip -net nsr1 link set veth0.10 down
-ip -net nsr1 link delete veth0.10 type vlan
-ip -net nsr1 link delete br0 type bridge
-ip -net ns1 addr flush dev eth0.10
-ip -net ns1 link set eth0.10 down
-ip -net ns1 link set eth0 down
-ip -net ns1 link delete eth0.10 type vlan
+ip -net $nsr1 link set veth0 nomaster
+ip -net $nsr1 link set veth0 down
+ip -net $nsr1 link set veth0.10 down
+ip -net $nsr1 link delete veth0.10 type vlan
+ip -net $nsr1 link delete br0 type bridge
+ip -net $ns1 addr flush dev eth0.10
+ip -net $ns1 link set eth0.10 down
+ip -net $ns1 link set eth0 down
+ip -net $ns1 link delete eth0.10 type vlan
 
 # restore address in ns1 and nsr1
-ip -net ns1 link set eth0 up
-ip -net ns1 addr add 10.0.1.99/24 dev eth0
-ip -net ns1 route add default via 10.0.1.1
-ip -net ns1 addr add dead:1::99/64 dev eth0
-ip -net ns1 route add default via dead:1::1
-ip -net nsr1 addr add 10.0.1.1/24 dev veth0
-ip -net nsr1 addr add dead:1::1/64 dev veth0
-ip -net nsr1 link set up dev veth0
+ip -net $ns1 link set eth0 up
+ip -net $ns1 addr add 10.0.1.99/24 dev eth0
+ip -net $ns1 route add default via 10.0.1.1
+ip -net $ns1 addr add dead:1::99/64 dev eth0
+ip -net $ns1 route add default via dead:1::1
+ip -net $nsr1 addr add 10.0.1.1/24 dev veth0
+ip -net $nsr1 addr add dead:1::1/64 dev veth0
+ip -net $nsr1 link set up dev veth0
 
 KEY_SHA="0x"$(ps -xaf | sha1sum | cut -d " " -f 1)
 KEY_AES="0x"$(ps -xaf | md5sum | cut -d " " -f 1)
@@ -480,23 +490,23 @@
 
 }
 
-do_esp nsr1 192.168.10.1 192.168.10.2 10.0.1.0/24 10.0.2.0/24 $SPI1 $SPI2
+do_esp $nsr1 192.168.10.1 192.168.10.2 10.0.1.0/24 10.0.2.0/24 $SPI1 $SPI2
 
-do_esp nsr2 192.168.10.2 192.168.10.1 10.0.2.0/24 10.0.1.0/24 $SPI2 $SPI1
+do_esp $nsr2 192.168.10.2 192.168.10.1 10.0.2.0/24 10.0.1.0/24 $SPI2 $SPI1
 
-ip netns exec nsr1 nft delete table ip nat
+ip netns exec $nsr1 nft delete table ip nat
 
 # restore default routes
-ip -net ns2 route del 192.168.10.1 via 10.0.2.1
-ip -net ns2 route add default via 10.0.2.1
-ip -net ns2 route add default via dead:2::1
+ip -net $ns2 route del 192.168.10.1 via 10.0.2.1
+ip -net $ns2 route add default via 10.0.2.1
+ip -net $ns2 route add default via dead:2::1
 
-if test_tcp_forwarding ns1 ns2; then
+if test_tcp_forwarding $ns1 $ns2; then
 	echo "PASS: ipsec tunnel mode for ns1/ns2"
 else
 	echo "FAIL: ipsec tunnel mode for ns1/ns2"
-	ip netns exec nsr1 nft list ruleset 1>&2
-	ip netns exec nsr1 cat /proc/net/xfrm_stat 1>&2
+	ip netns exec $nsr1 nft list ruleset 1>&2
+	ip netns exec $nsr1 cat /proc/net/xfrm_stat 1>&2
 fi
 
 exit $ret
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/netfilter/nft_nat.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/netfilter/nft_nat.sh
@@ -374,6 +374,47 @@
 	return $lret
 }
 
+test_local_dnat_portonly()
+{
+	local family=$1
+	local daddr=$2
+	local lret=0
+	local sr_s
+	local sr_r
+
+ip netns exec "$ns0" nft -f /dev/stdin <<EOF
+table $family nat {
+	chain output {
+		type nat hook output priority 0; policy accept;
+		meta l4proto tcp dnat to :2000
+
+	}
+}
+EOF
+	if [ $? -ne 0 ]; then
+		if [ $family = "inet" ];then
+			echo "SKIP: inet port test"
+			test_inet_nat=false
+			return
+		fi
+		echo "SKIP: Could not add $family dnat hook"
+		return
+	fi
+
+	echo SERVER-$family | ip netns exec "$ns1" timeout 5 socat -u STDIN TCP-LISTEN:2000 &
+	sc_s=$!
+
+	sleep 1
+
+	result=$(ip netns exec "$ns0" timeout 1 socat TCP:$daddr:2000 STDOUT)
+
+	if [ "$result" = "SERVER-inet" ];then
+		echo "PASS: inet port rewrite without l3 address"
+	else
+		echo "ERROR: inet port rewrite"
+		ret=1
+	fi
+}
 
 test_masquerade6()
 {
@@ -885,6 +926,144 @@
 	ip netns exec "$ns0" nft delete table $family nat
 }
 
+test_stateless_nat_ip()
+{
+	local lret=0
+
+	ip netns exec "$ns0" sysctl net.ipv4.conf.veth0.forwarding=1 > /dev/null
+	ip netns exec "$ns0" sysctl net.ipv4.conf.veth1.forwarding=1 > /dev/null
+
+	ip netns exec "$ns2" ping -q -c 1 10.0.1.99 > /dev/null # ping ns2->ns1
+	if [ $? -ne 0 ] ; then
+		echo "ERROR: cannot ping $ns1 from $ns2 before loading stateless rules"
+		return 1
+	fi
+
+ip netns exec "$ns0" nft -f /dev/stdin <<EOF
+table ip stateless {
+	map xlate_in {
+		typeof meta iifname . ip saddr . ip daddr : ip daddr
+		elements = {
+			"veth1" . 10.0.2.99 . 10.0.1.99 : 10.0.2.2,
+		}
+	}
+	map xlate_out {
+		typeof meta iifname . ip saddr . ip daddr : ip daddr
+		elements = {
+			"veth0" . 10.0.1.99 . 10.0.2.2 : 10.0.2.99
+		}
+	}
+
+	chain prerouting {
+		type filter hook prerouting priority -400; policy accept;
+		ip saddr set meta iifname . ip saddr . ip daddr map @xlate_in
+		ip daddr set meta iifname . ip saddr . ip daddr map @xlate_out
+	}
+}
+EOF
+	if [ $? -ne 0 ]; then
+		echo "SKIP: Could not add ip statless rules"
+		return $ksft_skip
+	fi
+
+	reset_counters
+
+	ip netns exec "$ns2" ping -q -c 1 10.0.1.99 > /dev/null # ping ns2->ns1
+	if [ $? -ne 0 ] ; then
+		echo "ERROR: cannot ping $ns1 from $ns2 with stateless rules"
+		lret=1
+	fi
+
+	# ns1 should have seen packets from .2.2, due to stateless rewrite.
+	expect="packets 1 bytes 84"
+	cnt=$(ip netns exec "$ns1" nft list counter inet filter ns0insl | grep -q "$expect")
+	if [ $? -ne 0 ]; then
+		bad_counter "$ns1" ns0insl "$expect" "test_stateless 1"
+		lret=1
+	fi
+
+	for dir in "in" "out" ; do
+		cnt=$(ip netns exec "$ns2" nft list counter inet filter ns1${dir} | grep -q "$expect")
+		if [ $? -ne 0 ]; then
+			bad_counter "$ns2" ns1$dir "$expect" "test_stateless 2"
+			lret=1
+		fi
+	done
+
+	# ns1 should not have seen packets from ns2, due to masquerade
+	expect="packets 0 bytes 0"
+	for dir in "in" "out" ; do
+		cnt=$(ip netns exec "$ns1" nft list counter inet filter ns2${dir} | grep -q "$expect")
+		if [ $? -ne 0 ]; then
+			bad_counter "$ns1" ns0$dir "$expect" "test_stateless 3"
+			lret=1
+		fi
+
+		cnt=$(ip netns exec "$ns0" nft list counter inet filter ns1${dir} | grep -q "$expect")
+		if [ $? -ne 0 ]; then
+			bad_counter "$ns0" ns1$dir "$expect" "test_stateless 4"
+			lret=1
+		fi
+	done
+
+	reset_counters
+
+	socat -h > /dev/null 2>&1
+	if [ $? -ne 0 ];then
+		echo "SKIP: Could not run stateless nat frag test without socat tool"
+		if [ $lret -eq 0 ]; then
+			return $ksft_skip
+		fi
+
+		ip netns exec "$ns0" nft delete table ip stateless
+		return $lret
+	fi
+
+	local tmpfile=$(mktemp)
+	dd if=/dev/urandom of=$tmpfile bs=4096 count=1 2>/dev/null
+
+	local outfile=$(mktemp)
+	ip netns exec "$ns1" timeout 3 socat -u UDP4-RECV:4233 OPEN:$outfile < /dev/null &
+	sc_r=$!
+
+	sleep 1
+	# re-do with large ping -> ip fragmentation
+	ip netns exec "$ns2" timeout 3 socat - UDP4-SENDTO:"10.0.1.99:4233" < "$tmpfile" > /dev/null
+	if [ $? -ne 0 ] ; then
+		echo "ERROR: failed to test udp $ns1 to $ns2 with stateless ip nat" 1>&2
+		lret=1
+	fi
+
+	wait
+
+	cmp "$tmpfile" "$outfile"
+	if [ $? -ne 0 ]; then
+		ls -l "$tmpfile" "$outfile"
+		echo "ERROR: in and output file mismatch when checking udp with stateless nat" 1>&2
+		lret=1
+	fi
+
+	rm -f "$tmpfile" "$outfile"
+
+	# ns1 should have seen packets from 2.2, due to stateless rewrite.
+	expect="packets 3 bytes 4164"
+	cnt=$(ip netns exec "$ns1" nft list counter inet filter ns0insl | grep -q "$expect")
+	if [ $? -ne 0 ]; then
+		bad_counter "$ns1" ns0insl "$expect" "test_stateless 5"
+		lret=1
+	fi
+
+	ip netns exec "$ns0" nft delete table ip stateless
+	if [ $? -ne 0 ]; then
+		echo "ERROR: Could not delete table ip stateless" 1>&2
+		lret=1
+	fi
+
+	test $lret -eq 0 && echo "PASS: IP statless for $ns2"
+
+	return $lret
+}
+
 # ip netns exec "$ns0" ping -c 1 -q 10.0.$i.99
 for i in 0 1 2; do
 ip netns exec ns$i-$sfx nft -f /dev/stdin <<EOF
@@ -951,6 +1130,19 @@
 EOF
 done
 
+# special case for stateless nat check, counter needs to
+# be done before (input) ip defragmentation
+ip netns exec ns1-$sfx nft -f /dev/stdin <<EOF
+table inet filter {
+	counter ns0insl {}
+
+	chain pre {
+		type filter hook prerouting priority -400; policy accept;
+		ip saddr 10.0.2.2 counter name "ns0insl"
+	}
+}
+EOF
+
 sleep 3
 # test basic connectivity
 for i in 1 2; do
@@ -984,6 +1176,10 @@
 reset_counters
 test_local_dnat ip
 test_local_dnat6 ip6
+
+reset_counters
+test_local_dnat_portonly inet 10.0.1.99
+
 reset_counters
 $test_inet_nat && test_local_dnat inet
 $test_inet_nat && test_local_dnat6 inet
@@ -1005,6 +1201,7 @@
 $test_inet_nat && test_redirect6 inet
 
 test_port_shadowing
+test_stateless_nat_ip
 
 if [ $ret -ne 0 ];then
 	echo -n "FAIL: "
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/openat2/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/openat2/Makefile
@@ -5,4 +5,4 @@
 
 include ../lib.mk
 
-$(TEST_GEN_PROGS): helpers.c
+$(TEST_GEN_PROGS): helpers.c helpers.h
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/openat2/helpers.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/openat2/helpers.h
@@ -9,6 +9,7 @@
 
 #define _GNU_SOURCE
 #include <stdint.h>
+#include <stdbool.h>
 #include <errno.h>
 #include <linux/types.h>
 #include "../kselftest.h"
@@ -62,11 +63,12 @@
 					(similar to chroot(2)). */
 #endif /* RESOLVE_IN_ROOT */
 
-#define E_func(func, ...)						\
-	do {								\
-		if (func(__VA_ARGS__) < 0)				\
-			ksft_exit_fail_msg("%s:%d %s failed\n", \
-					   __FILE__, __LINE__, #func);\
+#define E_func(func, ...)						      \
+	do {								      \
+		errno = 0;						      \
+		if (func(__VA_ARGS__) < 0)				      \
+			ksft_exit_fail_msg("%s:%d %s failed - errno:%d\n",    \
+					   __FILE__, __LINE__, #func, errno); \
 	} while (0)
 
 #define E_asprintf(...)		E_func(asprintf,	__VA_ARGS__)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/openat2/openat2_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/openat2/openat2_test.c
@@ -5,6 +5,7 @@
  */
 
 #define _GNU_SOURCE
+#define __SANE_USERSPACE_TYPES__ // Use ll64
 #include <fcntl.h>
 #include <sched.h>
 #include <sys/stat.h>
@@ -259,6 +260,16 @@
 		unlink(path);
 
 		fd = sys_openat2(AT_FDCWD, path, &test->how);
+		if (fd < 0 && fd == -EOPNOTSUPP) {
+			/*
+			 * Skip the testcase if it failed because not supported
+			 * by FS. (e.g. a valid O_TMPFILE combination on NFS)
+			 */
+			ksft_test_result_skip("openat2 with %s fails with %d (%s)\n",
+					      test->name, fd, strerror(-fd));
+			goto next;
+		}
+
 		if (test->err >= 0)
 			failed = (fd < 0);
 		else
@@ -303,7 +314,7 @@
 		else
 			resultfn("openat2 with %s fails with %d (%s)\n",
 				 test->name, test->err, strerror(-test->err));
-
+next:
 		free(fdpath);
 		fflush(stdout);
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/pidfd/pidfd.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/pidfd/pidfd.h
@@ -68,7 +68,7 @@
 #define PIDFD_SKIP 3
 #define PIDFD_XFAIL 4
 
-int wait_for_pid(pid_t pid)
+static inline int wait_for_pid(pid_t pid)
 {
 	int status, ret;
 
@@ -78,13 +78,20 @@
 		if (errno == EINTR)
 			goto again;
 
+		ksft_print_msg("waitpid returned -1, errno=%d\n", errno);
 		return -1;
 	}
 
-	if (!WIFEXITED(status))
+	if (!WIFEXITED(status)) {
+		ksft_print_msg(
+		       "waitpid !WIFEXITED, WIFSIGNALED=%d, WTERMSIG=%d\n",
+		       WIFSIGNALED(status), WTERMSIG(status));
 		return -1;
+	}
 
-	return WEXITSTATUS(status);
+	ret = WEXITSTATUS(status);
+	ksft_print_msg("waitpid WEXITSTATUS=%d\n", ret);
+	return ret;
 }
 
 static inline int sys_pidfd_open(pid_t pid, unsigned int flags)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/pidfd/pidfd_fdinfo_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/pidfd/pidfd_fdinfo_test.c
@@ -12,6 +12,7 @@
 #include <string.h>
 #include <syscall.h>
 #include <sys/wait.h>
+#include <sys/mman.h>
 
 #include "pidfd.h"
 #include "../kselftest.h"
@@ -61,7 +62,7 @@
 		break;
 
 	case PIDFD_PASS:
-		ksft_test_result_pass("%s test: Passed\n");
+		ksft_test_result_pass("%s test: Passed\n", test_name);
 		break;
 
 	default:
@@ -80,7 +81,10 @@
 	return err->code;
 }
 
+#define CHILD_STACK_SIZE 8192
+
 struct child {
+	char *stack;
 	pid_t pid;
 	int   fd;
 };
@@ -89,17 +93,22 @@
 				struct error *err)
 {
 	static int flags = CLONE_PIDFD | CLONE_NEWPID | CLONE_NEWNS | SIGCHLD;
-	size_t stack_size = 1024;
-	char *stack[1024] = { 0 };
 	struct child ret;
 
 	if (!(flags & CLONE_NEWUSER) && geteuid() != 0)
 		flags |= CLONE_NEWUSER;
 
+	ret.stack = mmap(NULL, CHILD_STACK_SIZE, PROT_READ | PROT_WRITE,
+			 MAP_PRIVATE | MAP_ANONYMOUS | MAP_STACK, -1, 0);
+	if (ret.stack == MAP_FAILED) {
+		error_set(err, -1, "mmap of stack failed (errno %d)", errno);
+		return ret;
+	}
+
 #ifdef __ia64__
-	ret.pid = __clone2(fn, stack, stack_size, flags, args, &ret.fd);
+	ret.pid = __clone2(fn, ret.stack, CHILD_STACK_SIZE, flags, args, &ret.fd);
 #else
-	ret.pid = clone(fn, stack + stack_size, flags, args, &ret.fd);
+	ret.pid = clone(fn, ret.stack + CHILD_STACK_SIZE, flags, args, &ret.fd);
 #endif
 
 	if (ret.pid < 0) {
@@ -129,6 +138,11 @@
 	else if (r > 0)
 		error_set(err, r, "child %d reported: %d", child->pid, r);
 
+	if (munmap(child->stack, CHILD_STACK_SIZE)) {
+		error_set(err, -1, "munmap of child stack failed (errno %d)", errno);
+		r = -1;
+	}
+
 	return r;
 }
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/pidfd/pidfd_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/pidfd/pidfd_test.c
@@ -380,13 +380,13 @@
 
 static void *test_pidfd_poll_exec_thread(void *priv)
 {
-	ksft_print_msg("Child Thread: starting. pid %d tid %d ; and sleeping\n",
+	ksft_print_msg("Child Thread: starting. pid %d tid %ld ; and sleeping\n",
 			getpid(), syscall(SYS_gettid));
 	ksft_print_msg("Child Thread: doing exec of sleep\n");
 
 	execl("/bin/sleep", "sleep", str(CHILD_THREAD_MIN_WAIT), (char *)NULL);
 
-	ksft_print_msg("Child Thread: DONE. pid %d tid %d\n",
+	ksft_print_msg("Child Thread: DONE. pid %d tid %ld\n",
 			getpid(), syscall(SYS_gettid));
 	return NULL;
 }
@@ -426,7 +426,7 @@
 {
 	pthread_t t1;
 
-	ksft_print_msg("Child (pidfd): starting. pid %d tid %d\n", getpid(),
+	ksft_print_msg("Child (pidfd): starting. pid %d tid %ld\n", getpid(),
 			syscall(SYS_gettid));
 	pthread_create(&t1, NULL, test_pidfd_poll_exec_thread, NULL);
 	/*
@@ -441,7 +441,6 @@
 {
 	int pid, pidfd = 0;
 	int status, ret;
-	pthread_t t1;
 	time_t prog_start = time(NULL);
 	const char *test_name = "pidfd_poll check for premature notification on child thread exec";
 
@@ -478,10 +477,10 @@
 
 static void *test_pidfd_poll_leader_exit_thread(void *priv)
 {
-	ksft_print_msg("Child Thread: starting. pid %d tid %d ; and sleeping\n",
+	ksft_print_msg("Child Thread: starting. pid %d tid %ld ; and sleeping\n",
 			getpid(), syscall(SYS_gettid));
 	sleep(CHILD_THREAD_MIN_WAIT);
-	ksft_print_msg("Child Thread: DONE. pid %d tid %d\n", getpid(), syscall(SYS_gettid));
+	ksft_print_msg("Child Thread: DONE. pid %d tid %ld\n", getpid(), syscall(SYS_gettid));
 	return NULL;
 }
 
@@ -490,7 +489,7 @@
 {
 	pthread_t t1, t2;
 
-	ksft_print_msg("Child: starting. pid %d tid %d\n", getpid(), syscall(SYS_gettid));
+	ksft_print_msg("Child: starting. pid %d tid %ld\n", getpid(), syscall(SYS_gettid));
 	pthread_create(&t1, NULL, test_pidfd_poll_leader_exit_thread, NULL);
 	pthread_create(&t2, NULL, test_pidfd_poll_leader_exit_thread, NULL);
 
@@ -500,13 +499,14 @@
 	 */
 	*child_exit_secs = time(NULL);
 	syscall(SYS_exit, 0);
+	/* Never reached, but appeases compiler thinking we should return. */
+	exit(0);
 }
 
 static void test_pidfd_poll_leader_exit(int use_waitpid)
 {
 	int pid, pidfd = 0;
-	int status, ret;
-	time_t prog_start = time(NULL);
+	int status, ret = 0;
 	const char *test_name = "pidfd_poll check for premature notification on non-empty"
 				"group leader exit";
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/pidfd/pidfd_wait.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/pidfd/pidfd_wait.c
@@ -39,7 +39,7 @@
 
 TEST(wait_simple)
 {
-	int pidfd = -1, status = 0;
+	int pidfd = -1;
 	pid_t parent_tid = -1;
 	struct clone_args args = {
 		.parent_tid = ptr_to_u64(&parent_tid),
@@ -47,7 +47,6 @@
 		.flags = CLONE_PIDFD | CLONE_PARENT_SETTID,
 		.exit_signal = SIGCHLD,
 	};
-	int ret;
 	pid_t pid;
 	siginfo_t info = {
 		.si_signo = 0,
@@ -88,7 +87,7 @@
 
 TEST(wait_states)
 {
-	int pidfd = -1, status = 0;
+	int pidfd = -1;
 	pid_t parent_tid = -1;
 	struct clone_args args = {
 		.parent_tid = ptr_to_u64(&parent_tid),
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/dscr/dscr_sysfs_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/dscr/dscr_sysfs_test.c
@@ -24,6 +24,7 @@
 	rc = read(fd, buf, sizeof(buf));
 	if (rc == -1) {
 		perror("read() failed");
+		close(fd);
 		return 1;
 	}
 	close(fd);
@@ -65,8 +66,10 @@
 		if (access(file, F_OK))
 			continue;
 
-		if (check_cpu_dscr_default(file, val))
+		if (check_cpu_dscr_default(file, val)) {
+			closedir(sysfs);
 			return 1;
+		}
 	}
 	closedir(sysfs);
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/math/fpu_preempt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/math/fpu_preempt.c
@@ -37,19 +37,20 @@
 int threads_starting;
 int running;
 
-extern void preempt_fpu(double *darray, int *threads_starting, int *running);
+extern int preempt_fpu(double *darray, int *threads_starting, int *running);
 
 void *preempt_fpu_c(void *p)
 {
+	long rc;
 	int i;
+
 	srand(pthread_self());
 	for (i = 0; i < 21; i++)
 		darray[i] = rand();
 
-	/* Test failed if it ever returns */
-	preempt_fpu(darray, &threads_starting, &running);
+	rc = preempt_fpu(darray, &threads_starting, &running);
 
-	return p;
+	return (void *)rc;
 }
 
 int test_preempt_fpu(void)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/math/vmx_preempt.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/math/vmx_preempt.c
@@ -37,19 +37,21 @@
 int threads_starting;
 int running;
 
-extern void preempt_vmx(vector int *varray, int *threads_starting, int *running);
+extern int preempt_vmx(vector int *varray, int *threads_starting, int *running);
 
 void *preempt_vmx_c(void *p)
 {
 	int i, j;
+	long rc;
+
 	srand(pthread_self());
 	for (i = 0; i < 12; i++)
 		for (j = 0; j < 4; j++)
 			varray[i][j] = rand();
 
-	/* Test fails if it ever returns */
-	preempt_vmx(varray, &threads_starting, &running);
-	return p;
+	rc = preempt_vmx(varray, &threads_starting, &running);
+
+	return (void *)rc;
 }
 
 int test_preempt_vmx(void)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/ptrace/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/ptrace/Makefile
@@ -7,7 +7,7 @@
 top_srcdir = ../../../../..
 include ../../lib.mk
 
-CFLAGS += -m64 -I../../../../../usr/include -I../tm -mhtm -fno-pie
+CFLAGS += -m64 -I../../../../../usr/include -I../tm -mhtm -fno-pie -Wno-error=deprecated
 
 $(OUTPUT)/ptrace-pkey $(OUTPUT)/core-pkey: child.h
 $(OUTPUT)/ptrace-pkey $(OUTPUT)/core-pkey: LDLIBS += -pthread
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/security/spectre_v2.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/security/spectre_v2.c
@@ -193,7 +193,7 @@
 			 * We are not vulnerable and reporting otherwise, so
 			 * missing such a mismatch is safe.
 			 */
-			if (state == VULNERABLE)
+			if (miss_percent > 95)
 				return 4;
 
 			return 1;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/signal/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/signal/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 TEST_GEN_PROGS := signal signal_tm sigfuz sigreturn_vdso sig_sc_double_restart
+TEST_GEN_PROGS += sigreturn_kernel
 
 CFLAGS += -maltivec
 $(OUTPUT)/signal_tm: CFLAGS += -mhtm
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/powerpc/signal/sigreturn_kernel.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/powerpc/signal/sigreturn_kernel.c
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Test that we can't sigreturn to kernel addresses, or to kernel mode.
+ */
+
+#define _GNU_SOURCE
+
+#include <stdio.h>
+#include <signal.h>
+#include <stdlib.h>
+#include <sys/types.h>
+#include <sys/wait.h>
+#include <unistd.h>
+
+#include "utils.h"
+
+#define MSR_PR (1ul << 14)
+
+static volatile unsigned long long sigreturn_addr;
+static volatile unsigned long long sigreturn_msr_mask;
+
+static void sigusr1_handler(int signo, siginfo_t *si, void *uc_ptr)
+{
+	ucontext_t *uc = (ucontext_t *)uc_ptr;
+
+	if (sigreturn_addr)
+		UCONTEXT_NIA(uc) = sigreturn_addr;
+
+	if (sigreturn_msr_mask)
+		UCONTEXT_MSR(uc) &= sigreturn_msr_mask;
+}
+
+static pid_t fork_child(void)
+{
+	pid_t pid;
+
+	pid = fork();
+	if (pid == 0) {
+		raise(SIGUSR1);
+		exit(0);
+	}
+
+	return pid;
+}
+
+static int expect_segv(pid_t pid)
+{
+	int child_ret;
+
+	waitpid(pid, &child_ret, 0);
+	FAIL_IF(WIFEXITED(child_ret));
+	FAIL_IF(!WIFSIGNALED(child_ret));
+	FAIL_IF(WTERMSIG(child_ret) != 11);
+
+	return 0;
+}
+
+int test_sigreturn_kernel(void)
+{
+	struct sigaction act;
+	int child_ret, i;
+	pid_t pid;
+
+	act.sa_sigaction = sigusr1_handler;
+	act.sa_flags = SA_SIGINFO;
+	sigemptyset(&act.sa_mask);
+
+	FAIL_IF(sigaction(SIGUSR1, &act, NULL));
+
+	for (i = 0; i < 2; i++) {
+		// Return to kernel
+		sigreturn_addr = 0xcull << 60;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return to kernel virtual
+		sigreturn_addr = 0xc008ull << 48;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return out of range
+		sigreturn_addr = 0xc010ull << 48;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return to no-man's land, just below PAGE_OFFSET
+		sigreturn_addr = (0xcull << 60) - (64 * 1024);
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return to no-man's land, above TASK_SIZE_4PB
+		sigreturn_addr = 0x1ull << 52;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return to 0xd space
+		sigreturn_addr = 0xdull << 60;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return to 0xe space
+		sigreturn_addr = 0xeull << 60;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Return to 0xf space
+		sigreturn_addr = 0xfull << 60;
+		pid = fork_child();
+		expect_segv(pid);
+
+		// Attempt to set PR=0 for 2nd loop (should be blocked by kernel)
+		sigreturn_msr_mask = ~MSR_PR;
+	}
+
+	printf("All children killed as expected\n");
+
+	// Don't change address, just MSR, should return to user as normal
+	sigreturn_addr = 0;
+	sigreturn_msr_mask = ~MSR_PR;
+	pid = fork_child();
+	waitpid(pid, &child_ret, 0);
+	FAIL_IF(!WIFEXITED(child_ret));
+	FAIL_IF(WIFSIGNALED(child_ret));
+	FAIL_IF(WEXITSTATUS(child_ret) != 0);
+
+	return 0;
+}
+
+int main(void)
+{
+	return test_harness(test_sigreturn_kernel, "sigreturn_kernel");
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/proc/proc-uptime-002.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/proc/proc-uptime-002.c
@@ -17,6 +17,7 @@
 // while shifting across CPUs.
 #undef NDEBUG
 #include <assert.h>
+#include <errno.h>
 #include <unistd.h>
 #include <sys/syscall.h>
 #include <stdlib.h>
@@ -54,7 +55,7 @@
 		len += sizeof(unsigned long);
 		free(m);
 		m = malloc(len);
-	} while (sys_sched_getaffinity(0, len, m) == -EINVAL);
+	} while (sys_sched_getaffinity(0, len, m) == -1 && errno == EINVAL);
 
 	fd = open("/proc/uptime", O_RDONLY);
 	assert(fd >= 0);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/ptp/testptp.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/ptp/testptp.c
@@ -492,11 +492,11 @@
 			interval = t2 - t1;
 			offset = (t2 + t1) / 2 - tp;
 
-			printf("system time: %lld.%u\n",
+			printf("system time: %lld.%09u\n",
 				(pct+2*i)->sec, (pct+2*i)->nsec);
-			printf("phc    time: %lld.%u\n",
+			printf("phc    time: %lld.%09u\n",
 				(pct+2*i+1)->sec, (pct+2*i+1)->nsec);
-			printf("system time: %lld.%u\n",
+			printf("system time: %lld.%09u\n",
 				(pct+2*i+2)->sec, (pct+2*i+2)->nsec);
 			printf("system/phc clock time offset is %" PRId64 " ns\n"
 			       "system     clock time delay  is %" PRId64 " ns\n",
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rcutorture/bin/torture.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rcutorture/bin/torture.sh
@@ -71,8 +71,8 @@
 	echo "       --configs-rcutorture \"config-file list w/ repeat factor (3*TINY01)\""
 	echo "       --configs-locktorture \"config-file list w/ repeat factor (10*LOCK01)\""
 	echo "       --configs-scftorture \"config-file list w/ repeat factor (2*CFLIST)\""
-	echo "       --doall"
-	echo "       --doallmodconfig / --do-no-allmodconfig"
+	echo "       --do-all"
+	echo "       --do-allmodconfig / --do-no-allmodconfig"
 	echo "       --do-clocksourcewd / --do-no-clocksourcewd"
 	echo "       --do-kasan / --do-no-kasan"
 	echo "       --do-kcsan / --do-no-kcsan"
@@ -386,16 +386,16 @@
 
 if test "$do_clocksourcewd" = "yes"
 then
-	torture_bootargs="rcupdate.rcu_cpu_stall_suppress_at_boot=1 torture.disable_onoff_at_boot rcupdate.rcu_task_stall_timeout=30000"
+	torture_bootargs="rcupdate.rcu_cpu_stall_suppress_at_boot=1 torture.disable_onoff_at_boot rcupdate.rcu_task_stall_timeout=30000 tsc=watchdog"
 	torture_set "clocksourcewd-1" tools/testing/selftests/rcutorture/bin/kvm.sh --allcpus --duration 45s --configs TREE03 --kconfig "CONFIG_TEST_CLOCKSOURCE_WATCHDOG=y" --trust-make
 
-	torture_bootargs="rcupdate.rcu_cpu_stall_suppress_at_boot=1 torture.disable_onoff_at_boot rcupdate.rcu_task_stall_timeout=30000 clocksource.max_cswd_read_retries=1"
+	torture_bootargs="rcupdate.rcu_cpu_stall_suppress_at_boot=1 torture.disable_onoff_at_boot rcupdate.rcu_task_stall_timeout=30000 tsc=watchdog"
 	torture_set "clocksourcewd-2" tools/testing/selftests/rcutorture/bin/kvm.sh --allcpus --duration 45s --configs TREE03 --kconfig "CONFIG_TEST_CLOCKSOURCE_WATCHDOG=y" --trust-make
 
 	# In case our work is already done...
 	if test "$do_rcutorture" != "yes"
 	then
-		torture_bootargs="rcupdate.rcu_cpu_stall_suppress_at_boot=1 torture.disable_onoff_at_boot rcupdate.rcu_task_stall_timeout=30000"
+		torture_bootargs="rcupdate.rcu_cpu_stall_suppress_at_boot=1 torture.disable_onoff_at_boot rcupdate.rcu_task_stall_timeout=30000 tsc=watchdog"
 		torture_set "clocksourcewd-3" tools/testing/selftests/rcutorture/bin/kvm.sh --allcpus --duration 45s --configs TREE03 --trust-make
 	fi
 fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rcutorture/configs/rcu/BUSTED-BOOST.boot
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rcutorture/configs/rcu/BUSTED-BOOST.boot
@@ -5,4 +5,4 @@
 rcutree.gp_cleanup_delay=3
 rcutree.kthread_prio=2
 threadirqs
-tree.use_softirq=0
+rcutree.use_softirq=0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rcutorture/configs/rcu/TREE03.boot
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rcutorture/configs/rcu/TREE03.boot
@@ -4,4 +4,4 @@
 rcutree.gp_cleanup_delay=3
 rcutree.kthread_prio=2
 threadirqs
-tree.use_softirq=0
+rcutree.use_softirq=0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/Makefile
@@ -1,17 +1,12 @@
-CC = $(CROSS_COMPILE)gcc
-CFLAGS = -g -Wall -O2 -D_FORTIFY_SOURCE=2
-SRCS=$(wildcard *.c)
-OBJS=$(SRCS:.c=.o)
+# SPDX-License-Identifier: GPL-2.0
 
-all: resctrl_tests
+CFLAGS = -g -Wall -O2 -D_FORTIFY_SOURCE=2 -D_GNU_SOURCE
+CFLAGS += $(KHDR_INCLUDES)
 
-$(OBJS): $(SRCS)
-	$(CC) $(CFLAGS) -c $(SRCS)
+TEST_GEN_PROGS := resctrl_tests
 
-resctrl_tests: $(OBJS)
-	$(CC) $(CFLAGS) -o $@ $^
+LOCAL_HDRS += $(wildcard *.h)
 
-.PHONY: clean
+include ../lib.mk
 
-clean:
-	$(RM) $(OBJS) resctrl_tests
+$(OUTPUT)/resctrl_tests: $(wildcard *.c)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/cache.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/cache.c
@@ -89,21 +89,19 @@
 static int get_llc_perf(unsigned long *llc_perf_miss)
 {
 	__u64 total_misses;
+	int ret;
 
 	/* Stop counters after one span to get miss rate */
 
 	ioctl(fd_lm, PERF_EVENT_IOC_DISABLE, 0);
 
-	if (read(fd_lm, &rf_cqm, sizeof(struct read_format)) == -1) {
+	ret = read(fd_lm, &rf_cqm, sizeof(struct read_format));
+	if (ret == -1) {
 		perror("Could not get llc misses through perf");
-
 		return -1;
 	}
 
 	total_misses = rf_cqm.values[0].value;
-
-	close(fd_lm);
-
 	*llc_perf_miss = total_misses;
 
 	return 0;
@@ -244,10 +242,12 @@
 	while (1) {
 		if (!strncmp(resctrl_val, CAT_STR, sizeof(CAT_STR))) {
 			ret = param->setup(1, param);
-			if (ret) {
+			if (ret == END_OF_TESTS) {
 				ret = 0;
 				break;
 			}
+			if (ret < 0)
+				break;
 			ret = reset_enable_llc_perf(bm_pid, param->cpu_no);
 			if (ret)
 				break;
@@ -256,19 +256,25 @@
 					 memflush, operation, resctrl_val)) {
 				fprintf(stderr, "Error-running fill buffer\n");
 				ret = -1;
-				break;
+				goto pe_close;
 			}
 
 			sleep(1);
 			ret = measure_cache_vals(param, bm_pid);
 			if (ret)
-				break;
+				goto pe_close;
+
+			close(fd_lm);
 		} else {
 			break;
 		}
 	}
 
 	return ret;
+
+pe_close:
+	close(fd_lm);
+	return ret;
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/cat_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/cat_test.c
@@ -40,7 +40,7 @@
 
 	/* Run NUM_OF_RUNS times */
 	if (p->num_of_runs >= NUM_OF_RUNS)
-		return -1;
+		return END_OF_TESTS;
 
 	if (p->num_of_runs == 0) {
 		sprintf(schemata, "%lx", p->mask);
@@ -89,7 +89,7 @@
 
 	return show_cache_info(sum_llc_perf_miss, no_of_bits, param->span / 64,
 			       MAX_DIFF, MAX_DIFF_PERCENT, NUM_OF_RUNS,
-			       !is_amd, false);
+			       get_vendor() == ARCH_INTEL, false);
 }
 
 void cat_test_cleanup(void)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/cmt_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/cmt_test.c
@@ -32,7 +32,7 @@
 
 	/* Run NUM_OF_RUNS times */
 	if (p->num_of_runs >= NUM_OF_RUNS)
-		return -1;
+		return END_OF_TESTS;
 
 	p->num_of_runs++;
 
@@ -91,9 +91,6 @@
 	if (ret)
 		return ret;
 
-	if (!validate_resctrl_feature_request(CMT_STR))
-		return -1;
-
 	ret = get_cbm_mask("L3", cbm_mask);
 	if (ret)
 		return ret;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/fill_buf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/fill_buf.c
@@ -68,6 +68,8 @@
 	size_t s64;
 
 	void *p = memalign(PAGE_SIZE, s);
+	if (!p)
+		return NULL;
 
 	p64 = (uint64_t *)p;
 	s64 = s / sizeof(uint64_t);
@@ -121,8 +123,10 @@
 
 	/* Consume read result so that reading memory is not optimized out. */
 	fp = fopen("/dev/null", "w");
-	if (!fp)
+	if (!fp) {
 		perror("Unable to write to /dev/null");
+		return -1;
+	}
 	fprintf(fp, "Sum: %d ", ret);
 	fclose(fp);
 
@@ -180,12 +184,13 @@
 	else
 		ret = fill_cache_write(start_ptr, end_ptr, resctrl_val);
 
+	free(startptr);
+
 	if (ret) {
 		printf("\n Error in fill cache read/write...\n");
 		return -1;
 	}
 
-	free(startptr);
 
 	return 0;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/mba_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/mba_test.c
@@ -12,7 +12,7 @@
 
 #define RESULT_FILE_NAME	"result_mba"
 #define NUM_OF_RUNS		5
-#define MAX_DIFF_PERCENT	5
+#define MAX_DIFF_PERCENT	8
 #define ALLOCATION_MAX		100
 #define ALLOCATION_MIN		10
 #define ALLOCATION_STEP		10
@@ -28,6 +28,7 @@
 	struct resctrl_val_param *p;
 	char allocation_str[64];
 	va_list param;
+	int ret;
 
 	va_start(param, num);
 	p = va_arg(param, struct resctrl_val_param *);
@@ -41,11 +42,15 @@
 		return 0;
 
 	if (allocation < ALLOCATION_MIN || allocation > ALLOCATION_MAX)
-		return -1;
+		return END_OF_TESTS;
 
 	sprintf(allocation_str, "%d", allocation);
 
-	write_schemata(p->ctrlgrp, allocation_str, p->cpu_no, p->resctrl_val);
+	ret = write_schemata(p->ctrlgrp, allocation_str, p->cpu_no,
+			     p->resctrl_val);
+	if (ret < 0)
+		return ret;
+
 	allocation -= ALLOCATION_STEP;
 
 	return 0;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/mbm_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/mbm_test.c
@@ -11,7 +11,7 @@
 #include "resctrl.h"
 
 #define RESULT_FILE_NAME	"result_mbm"
-#define MAX_DIFF_PERCENT	5
+#define MAX_DIFF_PERCENT	8
 #define NUM_OF_RUNS		5
 
 static int
@@ -95,7 +95,7 @@
 
 	/* Run NUM_OF_RUNS times */
 	if (num_of_runs++ >= NUM_OF_RUNS)
-		return -1;
+		return END_OF_TESTS;
 
 	va_start(param, num);
 	p = va_arg(param, struct resctrl_val_param *);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/resctrl.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/resctrl.h
@@ -1,5 +1,4 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-#define _GNU_SOURCE
 #ifndef RESCTRL_H
 #define RESCTRL_H
 #include <stdio.h>
@@ -34,10 +33,16 @@
 #define L3_MON_PATH		"/sys/fs/resctrl/info/L3_MON"
 #define L3_MON_FEATURES_PATH	"/sys/fs/resctrl/info/L3_MON/mon_features"
 
+#define ARCH_INTEL     1
+#define ARCH_AMD       2
+
+#define END_OF_TESTS	1
+
 #define PARENT_EXIT(err_msg)			\
 	do {					\
 		perror(err_msg);		\
 		kill(ppid, SIGKILL);		\
+		umount_resctrlfs();		\
 		exit(EXIT_FAILURE);		\
 	} while (0)
 
@@ -75,8 +80,8 @@
 extern pid_t bm_pid, ppid;
 
 extern char llc_occup_path[1024];
-extern bool is_amd;
 
+int get_vendor(void);
 bool check_resctrlfs_support(void);
 int filter_dmesg(void);
 int remount_resctrlfs(bool mum_resctrlfs);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/resctrl_tests.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/resctrl_tests.c
@@ -13,25 +13,41 @@
 #define BENCHMARK_ARGS		64
 #define BENCHMARK_ARG_SIZE	64
 
-bool is_amd;
-
-void detect_amd(void)
+static int detect_vendor(void)
 {
 	FILE *inf = fopen("/proc/cpuinfo", "r");
+	int vendor_id = 0;
+	char *s = NULL;
 	char *res;
 
 	if (!inf)
-		return;
+		return vendor_id;
 
 	res = fgrep(inf, "vendor_id");
 
-	if (res) {
-		char *s = strchr(res, ':');
+	if (res)
+		s = strchr(res, ':');
+
+	if (s && !strcmp(s, ": GenuineIntel\n"))
+		vendor_id = ARCH_INTEL;
+	else if (s && !strcmp(s, ": AuthenticAMD\n"))
+		vendor_id = ARCH_AMD;
 
-		is_amd = s && !strcmp(s, ": AuthenticAMD\n");
-		free(res);
-	}
 	fclose(inf);
+	free(res);
+	return vendor_id;
+}
+
+int get_vendor(void)
+{
+	static int vendor = -1;
+
+	if (vendor == -1)
+		vendor = detect_vendor();
+	if (vendor == 0)
+		ksft_print_msg("Can not get vendor info...\n");
+
+	return vendor;
 }
 
 static void cmd_help(void)
@@ -207,13 +223,15 @@
 	if (geteuid() != 0)
 		return ksft_exit_fail_msg("Not running as root, abort testing.\n");
 
-	/* Detect AMD vendor */
-	detect_amd();
-
 	if (has_ben) {
+		if (argc - ben_ind >= BENCHMARK_ARGS)
+			ksft_exit_fail_msg("Too long benchmark command.\n");
+
 		/* Extract benchmark command from command line. */
 		for (i = ben_ind; i < argc; i++) {
 			benchmark_cmd[i - ben_ind] = benchmark_cmd_area[i];
+			if (strlen(argv[i]) >= BENCHMARK_ARG_SIZE)
+				ksft_exit_fail_msg("Too long benchmark command argument.\n");
 			sprintf(benchmark_cmd[i - ben_ind], "%s", argv[i]);
 		}
 		benchmark_cmd[ben_count] = NULL;
@@ -241,10 +259,10 @@
 
 	ksft_set_plan(tests ? : 4);
 
-	if (!is_amd && mbm_test)
+	if ((get_vendor() == ARCH_INTEL) && mbm_test)
 		run_mbm_test(has_ben, benchmark_cmd, span, cpu_no, bw_report);
 
-	if (!is_amd && mba_test)
+	if ((get_vendor() == ARCH_INTEL) && mba_test)
 		run_mba_test(has_ben, benchmark_cmd, span, cpu_no, bw_report);
 
 	if (cmt_test)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/resctrl_val.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/resctrl_val.c
@@ -102,13 +102,12 @@
 	char *token[MAX_TOKENS];
 	int i = 0;
 
-	strcat(cas_count_cfg, ",");
 	token[0] = strtok(cas_count_cfg, "=,");
 
 	for (i = 1; i < MAX_TOKENS; i++)
 		token[i] = strtok(NULL, "=,");
 
-	for (i = 0; i < MAX_TOKENS; i++) {
+	for (i = 0; i < MAX_TOKENS - 1; i++) {
 		if (!token[i])
 			break;
 		if (strcmp(token[i], "event") == 0) {
@@ -733,29 +732,24 @@
 
 	/* Test runs until the callback setup() tells the test to stop. */
 	while (1) {
+		ret = param->setup(1, param);
+		if (ret == END_OF_TESTS) {
+			ret = 0;
+			break;
+		}
+		if (ret < 0)
+			break;
+
 		if (!strncmp(resctrl_val, MBM_STR, sizeof(MBM_STR)) ||
 		    !strncmp(resctrl_val, MBA_STR, sizeof(MBA_STR))) {
-			ret = param->setup(1, param);
-			if (ret) {
-				ret = 0;
-				break;
-			}
-
 			ret = measure_vals(param, &bw_resc_start);
 			if (ret)
 				break;
 		} else if (!strncmp(resctrl_val, CMT_STR, sizeof(CMT_STR))) {
-			ret = param->setup(1, param);
-			if (ret) {
-				ret = 0;
-				break;
-			}
 			sleep(1);
 			ret = measure_cache_vals(param, bm_pid);
 			if (ret)
 				break;
-		} else {
-			break;
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/resctrl/resctrlfs.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/resctrl/resctrlfs.c
@@ -106,7 +106,7 @@
 	char phys_pkg_path[1024];
 	FILE *fp;
 
-	if (is_amd)
+	if (get_vendor() == ARCH_AMD)
 		sprintf(phys_pkg_path, "%s%d/cache/index3/id",
 			PHYS_ID_PATH, cpu_no);
 	else
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/Makefile
@@ -4,9 +4,11 @@
 CLANG_FLAGS += -no-integrated-as
 endif
 
+top_srcdir = ../../../..
+
 CFLAGS += -O2 -Wall -g -I./ -I../../../../usr/include/ -L$(OUTPUT) -Wl,-rpath=./ \
-	  $(CLANG_FLAGS)
-LDLIBS += -lpthread
+	  $(CLANG_FLAGS) -I$(top_srcdir)/tools/include
+LDLIBS += -lpthread -ldl
 
 # Own dependencies because we only want to build against 1st prerequisite, but
 # still track changes to header files and depend on shared object.
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/basic_percpu_ops_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/basic_percpu_ops_test.c
@@ -9,10 +9,9 @@
 #include <string.h>
 #include <stddef.h>
 
+#include "../kselftest.h"
 #include "rseq.h"
 
-#define ARRAY_SIZE(arr)	(sizeof(arr) / sizeof((arr)[0]))
-
 struct percpu_lock_entry {
 	intptr_t v;
 } __attribute__((aligned(128)));
@@ -168,7 +167,7 @@
 	for (;;) {
 		struct percpu_list_node *head;
 		intptr_t *targetptr, expectnot, *load;
-		off_t offset;
+		long offset;
 		int ret, cpu;
 
 		cpu = rseq_cpu_start();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/compiler.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/compiler.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: LGPL-2.1-only OR MIT */
+/*
+ * rseq/compiler.h
+ *
+ * Work-around asm goto compiler bugs.
+ *
+ * (C) Copyright 2021 - Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+ */
+
+#ifndef RSEQ_COMPILER_H
+#define RSEQ_COMPILER_H
+
+/*
+ * gcc prior to 4.8.2 miscompiles asm goto.
+ * https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
+ *
+ * gcc prior to 8.1.0 miscompiles asm goto at O1.
+ * https://gcc.gnu.org/bugzilla/show_bug.cgi?id=103908
+ *
+ * clang prior to version 13.0.1 miscompiles asm goto at O2.
+ * https://github.com/llvm/llvm-project/issues/52735
+ *
+ * Work around these issues by adding a volatile inline asm with
+ * memory clobber in the fallthrough after the asm goto and at each
+ * label target.  Emit this for all compilers in case other similar
+ * issues are found in the future.
+ */
+#define rseq_after_asm_goto()	asm volatile ("" : : : "memory")
+
+#endif  /* RSEQ_COMPILER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/param_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/param_test.c
@@ -161,7 +161,7 @@
 	"	cbnz	" INJECT_ASM_REG ", 222b\n"			\
 	"333:\n"
 
-#elif __PPC__
+#elif defined(__PPC__)
 
 #define RSEQ_INJECT_INPUT \
 	, [loop_cnt_1]"m"(loop_cnt[1]) \
@@ -368,9 +368,7 @@
 		abort();
 	reps = thread_data->reps;
 	for (i = 0; i < reps; i++) {
-		int cpu = rseq_cpu_start();
-
-		cpu = rseq_this_cpu_lock(&data->lock);
+		int cpu = rseq_this_cpu_lock(&data->lock);
 		data->c[cpu].count++;
 		rseq_percpu_unlock(&data->lock, cpu);
 #ifndef BENCHMARK
@@ -551,7 +549,7 @@
 	for (;;) {
 		struct percpu_list_node *head;
 		intptr_t *targetptr, expectnot, *load;
-		off_t offset;
+		long offset;
 		int ret;
 
 		cpu = rseq_cpu_start();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-abi.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-abi.h
@@ -0,0 +1,151 @@
+/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
+#ifndef _RSEQ_ABI_H
+#define _RSEQ_ABI_H
+
+/*
+ * rseq-abi.h
+ *
+ * Restartable sequences system call API
+ *
+ * Copyright (c) 2015-2022 Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+ */
+
+#include <linux/types.h>
+#include <asm/byteorder.h>
+
+enum rseq_abi_cpu_id_state {
+	RSEQ_ABI_CPU_ID_UNINITIALIZED			= -1,
+	RSEQ_ABI_CPU_ID_REGISTRATION_FAILED		= -2,
+};
+
+enum rseq_abi_flags {
+	RSEQ_ABI_FLAG_UNREGISTER = (1 << 0),
+};
+
+enum rseq_abi_cs_flags_bit {
+	RSEQ_ABI_CS_FLAG_NO_RESTART_ON_PREEMPT_BIT	= 0,
+	RSEQ_ABI_CS_FLAG_NO_RESTART_ON_SIGNAL_BIT	= 1,
+	RSEQ_ABI_CS_FLAG_NO_RESTART_ON_MIGRATE_BIT	= 2,
+};
+
+enum rseq_abi_cs_flags {
+	RSEQ_ABI_CS_FLAG_NO_RESTART_ON_PREEMPT	=
+		(1U << RSEQ_ABI_CS_FLAG_NO_RESTART_ON_PREEMPT_BIT),
+	RSEQ_ABI_CS_FLAG_NO_RESTART_ON_SIGNAL	=
+		(1U << RSEQ_ABI_CS_FLAG_NO_RESTART_ON_SIGNAL_BIT),
+	RSEQ_ABI_CS_FLAG_NO_RESTART_ON_MIGRATE	=
+		(1U << RSEQ_ABI_CS_FLAG_NO_RESTART_ON_MIGRATE_BIT),
+};
+
+/*
+ * struct rseq_abi_cs is aligned on 4 * 8 bytes to ensure it is always
+ * contained within a single cache-line. It is usually declared as
+ * link-time constant data.
+ */
+struct rseq_abi_cs {
+	/* Version of this structure. */
+	__u32 version;
+	/* enum rseq_abi_cs_flags */
+	__u32 flags;
+	__u64 start_ip;
+	/* Offset from start_ip. */
+	__u64 post_commit_offset;
+	__u64 abort_ip;
+} __attribute__((aligned(4 * sizeof(__u64))));
+
+/*
+ * struct rseq_abi is aligned on 4 * 8 bytes to ensure it is always
+ * contained within a single cache-line.
+ *
+ * A single struct rseq_abi per thread is allowed.
+ */
+struct rseq_abi {
+	/*
+	 * Restartable sequences cpu_id_start field. Updated by the
+	 * kernel. Read by user-space with single-copy atomicity
+	 * semantics. This field should only be read by the thread which
+	 * registered this data structure. Aligned on 32-bit. Always
+	 * contains a value in the range of possible CPUs, although the
+	 * value may not be the actual current CPU (e.g. if rseq is not
+	 * initialized). This CPU number value should always be compared
+	 * against the value of the cpu_id field before performing a rseq
+	 * commit or returning a value read from a data structure indexed
+	 * using the cpu_id_start value.
+	 */
+	__u32 cpu_id_start;
+	/*
+	 * Restartable sequences cpu_id field. Updated by the kernel.
+	 * Read by user-space with single-copy atomicity semantics. This
+	 * field should only be read by the thread which registered this
+	 * data structure. Aligned on 32-bit. Values
+	 * RSEQ_CPU_ID_UNINITIALIZED and RSEQ_CPU_ID_REGISTRATION_FAILED
+	 * have a special semantic: the former means "rseq uninitialized",
+	 * and latter means "rseq initialization failed". This value is
+	 * meant to be read within rseq critical sections and compared
+	 * with the cpu_id_start value previously read, before performing
+	 * the commit instruction, or read and compared with the
+	 * cpu_id_start value before returning a value loaded from a data
+	 * structure indexed using the cpu_id_start value.
+	 */
+	__u32 cpu_id;
+	/*
+	 * Restartable sequences rseq_cs field.
+	 *
+	 * Contains NULL when no critical section is active for the current
+	 * thread, or holds a pointer to the currently active struct rseq_cs.
+	 *
+	 * Updated by user-space, which sets the address of the currently
+	 * active rseq_cs at the beginning of assembly instruction sequence
+	 * block, and set to NULL by the kernel when it restarts an assembly
+	 * instruction sequence block, as well as when the kernel detects that
+	 * it is preempting or delivering a signal outside of the range
+	 * targeted by the rseq_cs. Also needs to be set to NULL by user-space
+	 * before reclaiming memory that contains the targeted struct rseq_cs.
+	 *
+	 * Read and set by the kernel. Set by user-space with single-copy
+	 * atomicity semantics. This field should only be updated by the
+	 * thread which registered this data structure. Aligned on 64-bit.
+	 */
+	union {
+		__u64 ptr64;
+
+		/*
+		 * The "arch" field provides architecture accessor for
+		 * the ptr field based on architecture pointer size and
+		 * endianness.
+		 */
+		struct {
+#ifdef __LP64__
+			__u64 ptr;
+#elif defined(__BYTE_ORDER) ? (__BYTE_ORDER == __BIG_ENDIAN) : defined(__BIG_ENDIAN)
+			__u32 padding;		/* Initialized to zero. */
+			__u32 ptr;
+#else
+			__u32 ptr;
+			__u32 padding;		/* Initialized to zero. */
+#endif
+		} arch;
+	} rseq_cs;
+
+	/*
+	 * Restartable sequences flags field.
+	 *
+	 * This field should only be updated by the thread which
+	 * registered this data structure. Read by the kernel.
+	 * Mainly used for single-stepping through rseq critical sections
+	 * with debuggers.
+	 *
+	 * - RSEQ_ABI_CS_FLAG_NO_RESTART_ON_PREEMPT
+	 *     Inhibit instruction sequence block restart on preemption
+	 *     for this thread.
+	 * - RSEQ_ABI_CS_FLAG_NO_RESTART_ON_SIGNAL
+	 *     Inhibit instruction sequence block restart on signal
+	 *     delivery for this thread.
+	 * - RSEQ_ABI_CS_FLAG_NO_RESTART_ON_MIGRATE
+	 *     Inhibit instruction sequence block restart on migration for
+	 *     this thread.
+	 */
+	__u32 flags;
+} __attribute__((aligned(4 * sizeof(__u64))));
+
+#endif /* _RSEQ_ABI_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-arm.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-arm.h
@@ -147,14 +147,11 @@
 		teardown						\
 		"b %l[" __rseq_str(cmpfail_label) "]\n\t"
 
-#define rseq_workaround_gcc_asm_size_guess()	__asm__ __volatile__("")
-
 static inline __attribute__((always_inline))
 int rseq_cmpeqv_storev(intptr_t *v, intptr_t expect, intptr_t newv, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -185,8 +182,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -198,30 +195,31 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
 
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -255,8 +253,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expectnot]		"r" (expectnot),
@@ -270,19 +268,21 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -292,7 +292,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 #ifdef RSEQ_COMPARE_TWICE
@@ -316,8 +315,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"m" (*v),
 		  [count]		"Ir" (count)
 		  RSEQ_INJECT_INPUT
@@ -328,14 +327,15 @@
 		  , error1
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 #endif
 }
@@ -347,7 +347,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -381,8 +380,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -398,19 +397,21 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -422,7 +423,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -457,8 +457,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -474,19 +474,21 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -498,7 +500,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -537,8 +538,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* cmp2 input */
 		  [v2]			"m" (*v2),
 		  [expect2]		"r" (expect2),
@@ -554,21 +555,24 @@
 		  , error1, error2, error3
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("1st expected value comparison failed");
 error3:
+	rseq_after_asm_goto();
 	rseq_bug("2nd expected value comparison failed");
 #endif
 }
@@ -582,7 +586,6 @@
 
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -657,8 +660,8 @@
 		"8:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -678,21 +681,21 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -706,7 +709,6 @@
 
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -782,8 +784,8 @@
 		"8:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -803,21 +805,21 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
-	rseq_workaround_gcc_asm_size_guess();
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-arm64.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-arm64.h
@@ -230,8 +230,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"Qo" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -242,24 +242,28 @@
 		  , error1, error2
 #endif
 	);
-
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
 
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
@@ -287,8 +291,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"Qo" (*v),
 		  [expectnot]		"r" (expectnot),
 		  [load]		"Qo" (*load),
@@ -300,16 +304,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -337,8 +346,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"Qo" (*v),
 		  [count]		"r" (count)
 		  RSEQ_INJECT_INPUT
@@ -348,12 +357,15 @@
 		  , error1
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 #endif
 }
@@ -388,8 +400,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [expect]		"r" (expect),
 		  [v]			"Qo" (*v),
 		  [newv]		"r" (newv),
@@ -402,17 +414,21 @@
 		  , error1, error2
 #endif
 	);
-
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -447,8 +463,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [expect]		"r" (expect),
 		  [v]			"Qo" (*v),
 		  [newv]		"r" (newv),
@@ -461,17 +477,21 @@
 		  , error1, error2
 #endif
 	);
-
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -508,8 +528,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"Qo" (*v),
 		  [expect]		"r" (expect),
 		  [v2]			"Qo" (*v2),
@@ -522,19 +542,24 @@
 		  , error1, error2, error3
 #endif
 	);
-
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 error3:
+	rseq_after_asm_goto();
 	rseq_bug("2nd expected value comparison failed");
 #endif
 }
@@ -569,8 +594,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [expect]		"r" (expect),
 		  [v]			"Qo" (*v),
 		  [newv]		"r" (newv),
@@ -584,17 +609,21 @@
 		  , error1, error2
 #endif
 	);
-
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -629,8 +658,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"Qo" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"Qo" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [expect]		"r" (expect),
 		  [v]			"Qo" (*v),
 		  [newv]		"r" (newv),
@@ -644,17 +673,21 @@
 		  , error1, error2
 #endif
 	);
-
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-generic-thread-pointer.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-generic-thread-pointer.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: LGPL-2.1-only OR MIT */
+/*
+ * rseq-generic-thread-pointer.h
+ *
+ * (C) Copyright 2021 - Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+ */
+
+#ifndef _RSEQ_GENERIC_THREAD_POINTER
+#define _RSEQ_GENERIC_THREAD_POINTER
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Use gcc builtin thread pointer. */
+static inline void *rseq_thread_pointer(void)
+{
+	return __builtin_thread_pointer();
+}
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-mips.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-mips.h
@@ -154,14 +154,11 @@
 		teardown \
 		"b %l[" __rseq_str(cmpfail_label) "]\n\t"
 
-#define rseq_workaround_gcc_asm_size_guess()	__asm__ __volatile__("")
-
 static inline __attribute__((always_inline))
 int rseq_cmpeqv_storev(intptr_t *v, intptr_t expect, intptr_t newv, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -190,8 +187,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -203,14 +200,11 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
@@ -222,11 +216,10 @@
 
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -258,8 +251,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expectnot]		"r" (expectnot),
@@ -273,14 +266,11 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
@@ -295,7 +285,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 #ifdef RSEQ_COMPARE_TWICE
@@ -319,8 +308,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"m" (*v),
 		  [count]		"Ir" (count)
 		  RSEQ_INJECT_INPUT
@@ -331,10 +320,8 @@
 		  , error1
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
@@ -350,7 +337,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -382,8 +368,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -399,14 +385,11 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
@@ -423,7 +406,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -456,8 +438,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -473,14 +455,11 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
@@ -497,7 +476,6 @@
 {
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -532,8 +510,8 @@
 		"5:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* cmp2 input */
 		  [v2]			"m" (*v2),
 		  [expect2]		"r" (expect2),
@@ -549,14 +527,11 @@
 		  , error1, error2, error3
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
@@ -577,7 +552,6 @@
 
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -649,8 +623,8 @@
 		"8:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -670,21 +644,16 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
-	rseq_workaround_gcc_asm_size_guess();
 	rseq_bug("cpu_id comparison failed");
 error2:
-	rseq_workaround_gcc_asm_size_guess();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -698,7 +667,6 @@
 
 	RSEQ_INJECT_C(9)
 
-	rseq_workaround_gcc_asm_size_guess();
 	__asm__ __volatile__ goto (
 		RSEQ_ASM_DEFINE_TABLE(9, 1f, 2f, 4f) /* start, commit, abort */
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[cmpfail])
@@ -771,8 +739,8 @@
 		"8:\n\t"
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -792,21 +760,16 @@
 		  , error1, error2
 #endif
 	);
-	rseq_workaround_gcc_asm_size_guess();
 	return 0;
 abort:
-	rseq_workaround_gcc_asm_size_guess();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
-	rseq_workaround_gcc_asm_size_guess();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
-	rseq_workaround_gcc_asm_size_guess();
 	rseq_bug("cpu_id comparison failed");
 error2:
-	rseq_workaround_gcc_asm_size_guess();
 	rseq_bug("expected value comparison failed");
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-ppc-thread-pointer.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-ppc-thread-pointer.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: LGPL-2.1-only OR MIT */
+/*
+ * rseq-ppc-thread-pointer.h
+ *
+ * (C) Copyright 2021 - Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+ */
+
+#ifndef _RSEQ_PPC_THREAD_POINTER
+#define _RSEQ_PPC_THREAD_POINTER
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+static inline void *rseq_thread_pointer(void)
+{
+#ifdef __powerpc64__
+	register void *__result asm ("r13");
+#else
+	register void *__result asm ("r2");
+#endif
+	asm ("" : "=r" (__result));
+	return __result;
+}
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-ppc.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-ppc.h
@@ -47,10 +47,13 @@
 
 #ifdef __PPC64__
 
-#define STORE_WORD	"std "
-#define LOAD_WORD	"ld "
-#define LOADX_WORD	"ldx "
-#define CMP_WORD	"cmpd "
+#define RSEQ_STORE_LONG(arg)	"std%U[" __rseq_str(arg) "]%X[" __rseq_str(arg) "] "	/* To memory ("m" constraint) */
+#define RSEQ_STORE_INT(arg)	"stw%U[" __rseq_str(arg) "]%X[" __rseq_str(arg) "] "	/* To memory ("m" constraint) */
+#define RSEQ_LOAD_LONG(arg)	"ld%U[" __rseq_str(arg) "]%X[" __rseq_str(arg) "] "	/* From memory ("m" constraint) */
+#define RSEQ_LOAD_INT(arg)	"lwz%U[" __rseq_str(arg) "]%X[" __rseq_str(arg) "] "	/* From memory ("m" constraint) */
+#define RSEQ_LOADX_LONG		"ldx "							/* From base register ("b" constraint) */
+#define RSEQ_CMP_LONG		"cmpd "
+#define RSEQ_CMP_LONG_INT	"cmpdi "
 
 #define __RSEQ_ASM_DEFINE_TABLE(label, version, flags,				\
 			start_ip, post_commit_offset, abort_ip)			\
@@ -89,10 +92,13 @@
 
 #else /* #ifdef __PPC64__ */
 
-#define STORE_WORD	"stw "
-#define LOAD_WORD	"lwz "
-#define LOADX_WORD	"lwzx "
-#define CMP_WORD	"cmpw "
+#define RSEQ_STORE_LONG(arg)	"stw%U[" __rseq_str(arg) "]%X[" __rseq_str(arg) "] "	/* To memory ("m" constraint) */
+#define RSEQ_STORE_INT(arg)	RSEQ_STORE_LONG(arg)					/* To memory ("m" constraint) */
+#define RSEQ_LOAD_LONG(arg)	"lwz%U[" __rseq_str(arg) "]%X[" __rseq_str(arg) "] "	/* From memory ("m" constraint) */
+#define RSEQ_LOAD_INT(arg)	RSEQ_LOAD_LONG(arg)					/* From memory ("m" constraint) */
+#define RSEQ_LOADX_LONG		"lwzx "							/* From base register ("b" constraint) */
+#define RSEQ_CMP_LONG		"cmpw "
+#define RSEQ_CMP_LONG_INT	"cmpwi "
 
 #define __RSEQ_ASM_DEFINE_TABLE(label, version, flags,				\
 			start_ip, post_commit_offset, abort_ip)			\
@@ -125,7 +131,7 @@
 		RSEQ_INJECT_ASM(1)						\
 		"lis %%r17, (" __rseq_str(cs_label) ")@ha\n\t"			\
 		"addi %%r17, %%r17, (" __rseq_str(cs_label) ")@l\n\t"		\
-		"stw %%r17, %[" __rseq_str(rseq_cs) "]\n\t"			\
+		RSEQ_STORE_INT(rseq_cs) "%%r17, %[" __rseq_str(rseq_cs) "]\n\t"	\
 		__rseq_str(label) ":\n\t"
 
 #endif /* #ifdef __PPC64__ */
@@ -136,7 +142,7 @@
 
 #define RSEQ_ASM_CMP_CPU_ID(cpu_id, current_cpu_id, label)			\
 		RSEQ_INJECT_ASM(2)						\
-		"lwz %%r17, %[" __rseq_str(current_cpu_id) "]\n\t"		\
+		RSEQ_LOAD_INT(current_cpu_id) "%%r17, %[" __rseq_str(current_cpu_id) "]\n\t" \
 		"cmpw cr7, %[" __rseq_str(cpu_id) "], %%r17\n\t"		\
 		"bne- cr7, " __rseq_str(label) "\n\t"
 
@@ -153,25 +159,25 @@
  * 	RSEQ_ASM_OP_* (else): doesn't have hard-code registers(unless cr7)
  */
 #define RSEQ_ASM_OP_CMPEQ(var, expect, label)					\
-		LOAD_WORD "%%r17, %[" __rseq_str(var) "]\n\t"			\
-		CMP_WORD "cr7, %%r17, %[" __rseq_str(expect) "]\n\t"		\
+		RSEQ_LOAD_LONG(var) "%%r17, %[" __rseq_str(var) "]\n\t"		\
+		RSEQ_CMP_LONG "cr7, %%r17, %[" __rseq_str(expect) "]\n\t"		\
 		"bne- cr7, " __rseq_str(label) "\n\t"
 
 #define RSEQ_ASM_OP_CMPNE(var, expectnot, label)				\
-		LOAD_WORD "%%r17, %[" __rseq_str(var) "]\n\t"			\
-		CMP_WORD "cr7, %%r17, %[" __rseq_str(expectnot) "]\n\t"		\
+		RSEQ_LOAD_LONG(var) "%%r17, %[" __rseq_str(var) "]\n\t"		\
+		RSEQ_CMP_LONG "cr7, %%r17, %[" __rseq_str(expectnot) "]\n\t"		\
 		"beq- cr7, " __rseq_str(label) "\n\t"
 
 #define RSEQ_ASM_OP_STORE(value, var)						\
-		STORE_WORD "%[" __rseq_str(value) "], %[" __rseq_str(var) "]\n\t"
+		RSEQ_STORE_LONG(var) "%[" __rseq_str(value) "], %[" __rseq_str(var) "]\n\t"
 
 /* Load @var to r17 */
 #define RSEQ_ASM_OP_R_LOAD(var)							\
-		LOAD_WORD "%%r17, %[" __rseq_str(var) "]\n\t"
+		RSEQ_LOAD_LONG(var) "%%r17, %[" __rseq_str(var) "]\n\t"
 
 /* Store r17 to @var */
 #define RSEQ_ASM_OP_R_STORE(var)						\
-		STORE_WORD "%%r17, %[" __rseq_str(var) "]\n\t"
+		RSEQ_STORE_LONG(var) "%%r17, %[" __rseq_str(var) "]\n\t"
 
 /* Add @count to r17 */
 #define RSEQ_ASM_OP_R_ADD(count)						\
@@ -179,11 +185,11 @@
 
 /* Load (r17 + voffp) to r17 */
 #define RSEQ_ASM_OP_R_LOADX(voffp)						\
-		LOADX_WORD "%%r17, %[" __rseq_str(voffp) "], %%r17\n\t"
+		RSEQ_LOADX_LONG "%%r17, %[" __rseq_str(voffp) "], %%r17\n\t"
 
 /* TODO: implement a faster memcpy. */
 #define RSEQ_ASM_OP_R_MEMCPY() \
-		"cmpdi %%r19, 0\n\t" \
+		RSEQ_CMP_LONG_INT "%%r19, 0\n\t" \
 		"beq 333f\n\t" \
 		"addi %%r20, %%r20, -1\n\t" \
 		"addi %%r21, %%r21, -1\n\t" \
@@ -191,16 +197,16 @@
 		"lbzu %%r18, 1(%%r20)\n\t" \
 		"stbu %%r18, 1(%%r21)\n\t" \
 		"addi %%r19, %%r19, -1\n\t" \
-		"cmpdi %%r19, 0\n\t" \
+		RSEQ_CMP_LONG_INT "%%r19, 0\n\t" \
 		"bne 222b\n\t" \
 		"333:\n\t" \
 
 #define RSEQ_ASM_OP_R_FINAL_STORE(var, post_commit_label)			\
-		STORE_WORD "%%r17, %[" __rseq_str(var) "]\n\t"			\
+		RSEQ_STORE_LONG(var) "%%r17, %[" __rseq_str(var) "]\n\t"			\
 		__rseq_str(post_commit_label) ":\n\t"
 
 #define RSEQ_ASM_OP_FINAL_STORE(value, var, post_commit_label)			\
-		STORE_WORD "%[" __rseq_str(value) "], %[" __rseq_str(var) "]\n\t" \
+		RSEQ_STORE_LONG(var) "%[" __rseq_str(value) "], %[" __rseq_str(var) "]\n\t" \
 		__rseq_str(post_commit_label) ":\n\t"
 
 static inline __attribute__((always_inline))
@@ -235,8 +241,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -248,23 +254,28 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
 
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
@@ -301,8 +312,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expectnot]		"r" (expectnot),
@@ -316,16 +327,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -359,8 +375,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [count]		"r" (count)
@@ -372,12 +388,15 @@
 		  , error1
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 #endif
 }
@@ -419,8 +438,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -436,16 +455,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -489,8 +513,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -506,16 +530,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -560,8 +589,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* cmp2 input */
 		  [v2]			"m" (*v2),
 		  [expect2]		"r" (expect2),
@@ -577,18 +606,24 @@
 		  , error1, error2, error3
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("1st expected value comparison failed");
 error3:
+	rseq_after_asm_goto();
 	rseq_bug("2nd expected value comparison failed");
 #endif
 }
@@ -635,8 +670,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -653,16 +688,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -711,8 +751,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -729,23 +769,23 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
 
-#undef STORE_WORD
-#undef LOAD_WORD
-#undef LOADX_WORD
-#undef CMP_WORD
-
 #endif /* !RSEQ_SKIP_FASTPATH */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-s390.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-s390.h
@@ -165,8 +165,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -178,16 +178,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -198,7 +203,7 @@
  */
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
@@ -233,8 +238,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expectnot]		"r" (expectnot),
@@ -248,16 +253,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -288,8 +298,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [count]		"r" (count)
@@ -301,12 +311,15 @@
 		  , error1
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 #endif
 }
@@ -347,8 +360,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -364,16 +377,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -426,8 +444,8 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* cmp2 input */
 		  [v2]			"m" (*v2),
 		  [expect2]		"r" (expect2),
@@ -443,18 +461,24 @@
 		  , error1, error2, error3
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("1st expected value comparison failed");
 error3:
+	rseq_after_asm_goto();
 	rseq_bug("2nd expected value comparison failed");
 #endif
 }
@@ -534,8 +558,8 @@
 #endif
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [current_cpu_id]	"m" (__rseq_abi.cpu_id),
-		  [rseq_cs]		"m" (__rseq_abi.rseq_cs),
+		  [current_cpu_id]	"m" (rseq_get_abi()->cpu_id),
+		  [rseq_cs]		"m" (rseq_get_abi()->rseq_cs.arch.ptr),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -555,16 +579,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-skip.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-skip.h
@@ -13,7 +13,7 @@
 
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	return -1;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-thread-pointer.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-thread-pointer.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: LGPL-2.1-only OR MIT */
+/*
+ * rseq-thread-pointer.h
+ *
+ * (C) Copyright 2021 - Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+ */
+
+#ifndef _RSEQ_THREAD_POINTER
+#define _RSEQ_THREAD_POINTER
+
+#if defined(__x86_64__) || defined(__i386__)
+#include "rseq-x86-thread-pointer.h"
+#elif defined(__PPC__)
+#include "rseq-ppc-thread-pointer.h"
+#else
+#include "rseq-generic-thread-pointer.h"
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-x86-thread-pointer.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-x86-thread-pointer.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: LGPL-2.1-only OR MIT */
+/*
+ * rseq-x86-thread-pointer.h
+ *
+ * (C) Copyright 2021 - Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+ */
+
+#ifndef _RSEQ_X86_THREAD_POINTER
+#define _RSEQ_X86_THREAD_POINTER
+
+#include <features.h>
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if __GNUC_PREREQ (11, 1)
+static inline void *rseq_thread_pointer(void)
+{
+	return __builtin_thread_pointer();
+}
+#else
+static inline void *rseq_thread_pointer(void)
+{
+	void *__result;
+
+# ifdef __x86_64__
+	__asm__ ("mov %%fs:0, %0" : "=r" (__result));
+# else
+	__asm__ ("mov %%gs:0, %0" : "=r" (__result));
+# endif
+	return __result;
+}
+#endif /* !GCC 11 */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq-x86.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq-x86.h
@@ -28,6 +28,8 @@
 
 #ifdef __x86_64__
 
+#define RSEQ_ASM_TP_SEGMENT	%%fs
+
 #define rseq_smp_mb()	\
 	__asm__ __volatile__ ("lock; addl $0,-128(%%rsp)" ::: "memory", "cc")
 #define rseq_smp_rmb()	rseq_barrier()
@@ -123,14 +125,14 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpq %[v], %[expect]\n\t"
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"cmpq %[v], %[expect]\n\t"
 		"jnz %l[error2]\n\t"
 #endif
@@ -141,7 +143,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -152,16 +154,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -172,7 +179,7 @@
  */
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
@@ -184,15 +191,15 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"movq %[v], %%rbx\n\t"
 		"cmpq %%rbx, %[expectnot]\n\t"
 		"je %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"movq %[v], %%rbx\n\t"
 		"cmpq %%rbx, %[expectnot]\n\t"
 		"je %l[error2]\n\t"
@@ -207,7 +214,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expectnot]		"r" (expectnot),
@@ -220,16 +227,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -245,11 +257,11 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error1])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 #endif
 		/* final store */
 		"addq %[count], %[v]\n\t"
@@ -258,7 +270,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [count]		"er" (count)
@@ -269,12 +281,15 @@
 		  , error1
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 #endif
 }
@@ -286,7 +301,7 @@
  *  *pval += inc;
  */
 static inline __attribute__((always_inline))
-int rseq_offset_deref_addv(intptr_t *ptr, off_t off, intptr_t inc, int cpu)
+int rseq_offset_deref_addv(intptr_t *ptr, long off, intptr_t inc, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
@@ -296,11 +311,11 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error1])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 #endif
 		/* get p+v */
 		"movq %[ptr], %%rbx\n\t"
@@ -314,7 +329,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [ptr]			"m" (*ptr),
 		  [off]			"er" (off),
@@ -351,14 +366,14 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpq %[v], %[expect]\n\t"
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"cmpq %[v], %[expect]\n\t"
 		"jnz %l[error2]\n\t"
 #endif
@@ -372,7 +387,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -387,16 +402,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -426,8 +446,8 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error3])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpq %[v], %[expect]\n\t"
 		"jnz %l[cmpfail]\n\t"
@@ -436,7 +456,7 @@
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(5)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"cmpq %[v], %[expect]\n\t"
 		"jnz %l[error2]\n\t"
 		"cmpq %[v2], %[expect2]\n\t"
@@ -449,7 +469,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* cmp2 input */
 		  [v2]			"m" (*v2),
 		  [expect2]		"r" (expect2),
@@ -464,18 +484,24 @@
 		  , error1, error2, error3
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("1st expected value comparison failed");
 error3:
+	rseq_after_asm_goto();
 	rseq_bug("2nd expected value comparison failed");
 #endif
 }
@@ -500,14 +526,14 @@
 		"movq %[dst], %[rseq_scratch1]\n\t"
 		"movq %[len], %[rseq_scratch2]\n\t"
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpq %[v], %[expect]\n\t"
 		"jnz 5f\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 6f)
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 6f)
 		"cmpq %[v], %[expect]\n\t"
 		"jnz 7f\n\t"
 #endif
@@ -555,7 +581,7 @@
 #endif
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
@@ -574,16 +600,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -600,7 +631,9 @@
 
 #endif /* !RSEQ_SKIP_FASTPATH */
 
-#elif __i386__
+#elif defined(__i386__)
+
+#define RSEQ_ASM_TP_SEGMENT	%%gs
 
 #define rseq_smp_mb()	\
 	__asm__ __volatile__ ("lock; addl $0,-128(%%esp)" ::: "memory", "cc")
@@ -701,14 +734,14 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpl %[v], %[expect]\n\t"
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"cmpl %[v], %[expect]\n\t"
 		"jnz %l[error2]\n\t"
 #endif
@@ -719,7 +752,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  [v]			"m" (*v),
 		  [expect]		"r" (expect),
 		  [newv]		"r" (newv)
@@ -730,16 +763,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -750,7 +788,7 @@
  */
 static inline __attribute__((always_inline))
 int rseq_cmpnev_storeoffp_load(intptr_t *v, intptr_t expectnot,
-			       off_t voffp, intptr_t *load, int cpu)
+			       long voffp, intptr_t *load, int cpu)
 {
 	RSEQ_INJECT_C(9)
 
@@ -762,15 +800,15 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"movl %[v], %%ebx\n\t"
 		"cmpl %%ebx, %[expectnot]\n\t"
 		"je %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"movl %[v], %%ebx\n\t"
 		"cmpl %%ebx, %[expectnot]\n\t"
 		"je %l[error2]\n\t"
@@ -785,7 +823,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expectnot]		"r" (expectnot),
@@ -798,16 +836,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -823,11 +866,11 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error1])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 #endif
 		/* final store */
 		"addl %[count], %[v]\n\t"
@@ -836,7 +879,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [count]		"ir" (count)
@@ -847,12 +890,15 @@
 		  , error1
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 #endif
 }
@@ -872,14 +918,14 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpl %[v], %[expect]\n\t"
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"cmpl %[v], %[expect]\n\t"
 		"jnz %l[error2]\n\t"
 #endif
@@ -894,7 +940,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"m" (newv2),
@@ -909,16 +955,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -938,15 +989,15 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error2])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"movl %[expect], %%eax\n\t"
 		"cmpl %[v], %%eax\n\t"
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"movl %[expect], %%eax\n\t"
 		"cmpl %[v], %%eax\n\t"
 		"jnz %l[error2]\n\t"
@@ -962,7 +1013,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* try store input */
 		  [v2]			"m" (*v2),
 		  [newv2]		"r" (newv2),
@@ -977,16 +1028,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 
@@ -1008,8 +1064,8 @@
 		RSEQ_ASM_DEFINE_EXIT_POINT(1f, %l[error3])
 #endif
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"cmpl %[v], %[expect]\n\t"
 		"jnz %l[cmpfail]\n\t"
@@ -1018,7 +1074,7 @@
 		"jnz %l[cmpfail]\n\t"
 		RSEQ_INJECT_ASM(5)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), %l[error1])
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), %l[error1])
 		"cmpl %[v], %[expect]\n\t"
 		"jnz %l[error2]\n\t"
 		"cmpl %[expect2], %[v2]\n\t"
@@ -1032,7 +1088,7 @@
 		RSEQ_ASM_DEFINE_ABORT(4, "", abort)
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* cmp2 input */
 		  [v2]			"m" (*v2),
 		  [expect2]		"r" (expect2),
@@ -1047,18 +1103,24 @@
 		  , error1, error2, error3
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("1st expected value comparison failed");
 error3:
+	rseq_after_asm_goto();
 	rseq_bug("2nd expected value comparison failed");
 #endif
 }
@@ -1084,15 +1146,15 @@
 		"movl %[dst], %[rseq_scratch1]\n\t"
 		"movl %[len], %[rseq_scratch2]\n\t"
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"movl %[expect], %%eax\n\t"
 		"cmpl %%eax, %[v]\n\t"
 		"jnz 5f\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 6f)
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 6f)
 		"movl %[expect], %%eax\n\t"
 		"cmpl %%eax, %[v]\n\t"
 		"jnz 7f\n\t"
@@ -1142,7 +1204,7 @@
 #endif
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"m" (expect),
@@ -1161,16 +1223,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
@@ -1196,15 +1263,15 @@
 		"movl %[dst], %[rseq_scratch1]\n\t"
 		"movl %[len], %[rseq_scratch2]\n\t"
 		/* Start rseq by storing table entry pointer into rseq_cs. */
-		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_CS_OFFSET(%[rseq_abi]))
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 4f)
+		RSEQ_ASM_STORE_RSEQ_CS(1, 3b, RSEQ_ASM_TP_SEGMENT:RSEQ_CS_OFFSET(%[rseq_offset]))
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 4f)
 		RSEQ_INJECT_ASM(3)
 		"movl %[expect], %%eax\n\t"
 		"cmpl %%eax, %[v]\n\t"
 		"jnz 5f\n\t"
 		RSEQ_INJECT_ASM(4)
 #ifdef RSEQ_COMPARE_TWICE
-		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_CPU_ID_OFFSET(%[rseq_abi]), 6f)
+		RSEQ_ASM_CMP_CPU_ID(cpu_id, RSEQ_ASM_TP_SEGMENT:RSEQ_CPU_ID_OFFSET(%[rseq_offset]), 6f)
 		"movl %[expect], %%eax\n\t"
 		"cmpl %%eax, %[v]\n\t"
 		"jnz 7f\n\t"
@@ -1255,7 +1322,7 @@
 #endif
 		: /* gcc asm goto does not allow outputs */
 		: [cpu_id]		"r" (cpu),
-		  [rseq_abi]		"r" (&__rseq_abi),
+		  [rseq_offset]		"r" (rseq_offset),
 		  /* final store input */
 		  [v]			"m" (*v),
 		  [expect]		"m" (expect),
@@ -1274,16 +1341,21 @@
 		  , error1, error2
 #endif
 	);
+	rseq_after_asm_goto();
 	return 0;
 abort:
+	rseq_after_asm_goto();
 	RSEQ_INJECT_FAILED
 	return -1;
 cmpfail:
+	rseq_after_asm_goto();
 	return 1;
 #ifdef RSEQ_COMPARE_TWICE
 error1:
+	rseq_after_asm_goto();
 	rseq_bug("cpu_id comparison failed");
 error2:
+	rseq_after_asm_goto();
 	rseq_bug("expected value comparison failed");
 #endif
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq.c
@@ -26,104 +26,133 @@
 #include <assert.h>
 #include <signal.h>
 #include <limits.h>
+#include <dlfcn.h>
+#include <stddef.h>
 
-#include "rseq.h"
-
-#define ARRAY_SIZE(arr)	(sizeof(arr) / sizeof((arr)[0]))
+#include <linux/compiler.h>
 
-__thread volatile struct rseq __rseq_abi = {
-	.cpu_id = RSEQ_CPU_ID_UNINITIALIZED,
-};
+#include "../kselftest.h"
+#include "rseq.h"
 
 /*
- * Shared with other libraries. This library may take rseq ownership if it is
- * still 0 when executing the library constructor. Set to 1 by library
- * constructor when handling rseq. Set to 0 in destructor if handling rseq.
+ * Define weak versions to play nice with binaries that are statically linked
+ * against a libc that doesn't support registering its own rseq.
  */
-int __rseq_handled;
+__weak ptrdiff_t __rseq_offset;
+__weak unsigned int __rseq_size;
+__weak unsigned int __rseq_flags;
+
+static const ptrdiff_t *libc_rseq_offset_p = &__rseq_offset;
+static const unsigned int *libc_rseq_size_p = &__rseq_size;
+static const unsigned int *libc_rseq_flags_p = &__rseq_flags;
+
+/* Offset from the thread pointer to the rseq area.  */
+ptrdiff_t rseq_offset;
+
+/* Size of the registered rseq area.  0 if the registration was
+   unsuccessful.  */
+unsigned int rseq_size = -1U;
+
+/* Flags used during rseq registration.  */
+unsigned int rseq_flags;
 
-/* Whether this library have ownership of rseq registration. */
 static int rseq_ownership;
 
-static __thread volatile uint32_t __rseq_refcount;
+static
+__thread struct rseq_abi __rseq_abi __attribute__((tls_model("initial-exec"))) = {
+	.cpu_id = RSEQ_ABI_CPU_ID_UNINITIALIZED,
+};
 
-static void signal_off_save(sigset_t *oldset)
+static int sys_rseq(struct rseq_abi *rseq_abi, uint32_t rseq_len,
+		    int flags, uint32_t sig)
 {
-	sigset_t set;
-	int ret;
-
-	sigfillset(&set);
-	ret = pthread_sigmask(SIG_BLOCK, &set, oldset);
-	if (ret)
-		abort();
+	return syscall(__NR_rseq, rseq_abi, rseq_len, flags, sig);
 }
 
-static void signal_restore(sigset_t oldset)
+int rseq_available(void)
 {
-	int ret;
+	int rc;
 
-	ret = pthread_sigmask(SIG_SETMASK, &oldset, NULL);
-	if (ret)
+	rc = sys_rseq(NULL, 0, 0, 0);
+	if (rc != -1)
 		abort();
-}
-
-static int sys_rseq(volatile struct rseq *rseq_abi, uint32_t rseq_len,
-		    int flags, uint32_t sig)
-{
-	return syscall(__NR_rseq, rseq_abi, rseq_len, flags, sig);
+	switch (errno) {
+	case ENOSYS:
+		return 0;
+	case EINVAL:
+		return 1;
+	default:
+		abort();
+	}
 }
 
 int rseq_register_current_thread(void)
 {
-	int rc, ret = 0;
-	sigset_t oldset;
+	int rc;
 
-	if (!rseq_ownership)
+	if (!rseq_ownership) {
+		/* Treat libc's ownership as a successful registration. */
 		return 0;
-	signal_off_save(&oldset);
-	if (__rseq_refcount == UINT_MAX) {
-		ret = -1;
-		goto end;
-	}
-	if (__rseq_refcount++)
-		goto end;
-	rc = sys_rseq(&__rseq_abi, sizeof(struct rseq), 0, RSEQ_SIG);
-	if (!rc) {
-		assert(rseq_current_cpu_raw() >= 0);
-		goto end;
-	}
-	if (errno != EBUSY)
-		__rseq_abi.cpu_id = RSEQ_CPU_ID_REGISTRATION_FAILED;
-	ret = -1;
-	__rseq_refcount--;
-end:
-	signal_restore(oldset);
-	return ret;
+	}
+	rc = sys_rseq(&__rseq_abi, sizeof(struct rseq_abi), 0, RSEQ_SIG);
+	if (rc)
+		return -1;
+	assert(rseq_current_cpu_raw() >= 0);
+	return 0;
 }
 
 int rseq_unregister_current_thread(void)
 {
-	int rc, ret = 0;
-	sigset_t oldset;
+	int rc;
 
-	if (!rseq_ownership)
+	if (!rseq_ownership) {
+		/* Treat libc's ownership as a successful unregistration. */
 		return 0;
-	signal_off_save(&oldset);
-	if (!__rseq_refcount) {
-		ret = -1;
-		goto end;
-	}
-	if (--__rseq_refcount)
-		goto end;
-	rc = sys_rseq(&__rseq_abi, sizeof(struct rseq),
-		      RSEQ_FLAG_UNREGISTER, RSEQ_SIG);
-	if (!rc)
-		goto end;
-	__rseq_refcount = 1;
-	ret = -1;
-end:
-	signal_restore(oldset);
-	return ret;
+	}
+	rc = sys_rseq(&__rseq_abi, sizeof(struct rseq_abi), RSEQ_ABI_FLAG_UNREGISTER, RSEQ_SIG);
+	if (rc)
+		return -1;
+	return 0;
+}
+
+static __attribute__((constructor))
+void rseq_init(void)
+{
+	/*
+	 * If the libc's registered rseq size isn't already valid, it may be
+	 * because the binary is dynamically linked and not necessarily due to
+	 * libc not having registered a restartable sequence.  Try to find the
+	 * symbols if that's the case.
+	 */
+	if (!*libc_rseq_size_p) {
+		libc_rseq_offset_p = dlsym(RTLD_NEXT, "__rseq_offset");
+		libc_rseq_size_p = dlsym(RTLD_NEXT, "__rseq_size");
+		libc_rseq_flags_p = dlsym(RTLD_NEXT, "__rseq_flags");
+	}
+	if (libc_rseq_size_p && libc_rseq_offset_p && libc_rseq_flags_p &&
+			*libc_rseq_size_p != 0) {
+		/* rseq registration owned by glibc */
+		rseq_offset = *libc_rseq_offset_p;
+		rseq_size = *libc_rseq_size_p;
+		rseq_flags = *libc_rseq_flags_p;
+		return;
+	}
+	if (!rseq_available())
+		return;
+	rseq_ownership = 1;
+	rseq_offset = (void *)&__rseq_abi - rseq_thread_pointer();
+	rseq_size = sizeof(struct rseq_abi);
+	rseq_flags = 0;
+}
+
+static __attribute__((destructor))
+void rseq_exit(void)
+{
+	if (!rseq_ownership)
+		return;
+	rseq_offset = 0;
+	rseq_size = -1U;
+	rseq_ownership = 0;
 }
 
 int32_t rseq_fallback_current_cpu(void)
@@ -137,20 +166,3 @@
 	}
 	return cpu;
 }
-
-void __attribute__((constructor)) rseq_init(void)
-{
-	/* Check whether rseq is handled by another library. */
-	if (__rseq_handled)
-		return;
-	__rseq_handled = 1;
-	rseq_ownership = 1;
-}
-
-void __attribute__((destructor)) rseq_fini(void)
-{
-	if (!rseq_ownership)
-		return;
-	__rseq_handled = 0;
-	rseq_ownership = 0;
-}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rseq/rseq.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rseq/rseq.h
@@ -16,7 +16,9 @@
 #include <errno.h>
 #include <stdio.h>
 #include <stdlib.h>
-#include <linux/rseq.h>
+#include <stddef.h>
+#include "rseq-abi.h"
+#include "compiler.h"
 
 /*
  * Empty code injection macros, override when testing.
@@ -43,8 +45,20 @@
 #define RSEQ_INJECT_FAILED
 #endif
 
-extern __thread volatile struct rseq __rseq_abi;
-extern int __rseq_handled;
+#include "rseq-thread-pointer.h"
+
+/* Offset from the thread pointer to the rseq area.  */
+extern ptrdiff_t rseq_offset;
+/* Size of the registered rseq area.  0 if the registration was
+   unsuccessful.  */
+extern unsigned int rseq_size;
+/* Flags used during rseq registration.  */
+extern unsigned int rseq_flags;
+
+static inline struct rseq_abi *rseq_get_abi(void)
+{
+	return (struct rseq_abi *) ((uintptr_t) rseq_thread_pointer() + rseq_offset);
+}
 
 #define rseq_likely(x)		__builtin_expect(!!(x), 1)
 #define rseq_unlikely(x)	__builtin_expect(!!(x), 0)
@@ -108,7 +122,7 @@
  */
 static inline int32_t rseq_current_cpu_raw(void)
 {
-	return RSEQ_ACCESS_ONCE(__rseq_abi.cpu_id);
+	return RSEQ_ACCESS_ONCE(rseq_get_abi()->cpu_id);
 }
 
 /*
@@ -124,7 +138,7 @@
  */
 static inline uint32_t rseq_cpu_start(void)
 {
-	return RSEQ_ACCESS_ONCE(__rseq_abi.cpu_id_start);
+	return RSEQ_ACCESS_ONCE(rseq_get_abi()->cpu_id_start);
 }
 
 static inline uint32_t rseq_current_cpu(void)
@@ -139,11 +153,7 @@
 
 static inline void rseq_clear_rseq_cs(void)
 {
-#ifdef __LP64__
-	__rseq_abi.rseq_cs.ptr = 0;
-#else
-	__rseq_abi.rseq_cs.ptr.ptr32 = 0;
-#endif
+	RSEQ_WRITE_ONCE(rseq_get_abi()->rseq_cs.arch.ptr, 0);
 }
 
 /*
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/rtc/settings
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/rtc/settings
@@ -1 +1 @@
-timeout=90
+timeout=180
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/sched/cs_prctl_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/sched/cs_prctl_test.c
@@ -62,6 +62,17 @@
 
 const int THREAD_CLONE_FLAGS = CLONE_THREAD | CLONE_SIGHAND | CLONE_FS | CLONE_VM | CLONE_FILES;
 
+struct child_args {
+	int num_threads;
+	int pfd[2];
+	int cpid;
+	int thr_tids[MAX_THREADS];
+};
+
+static struct child_args procs[MAX_PROCESSES];
+static int num_processes = 2;
+static int need_cleanup = 0;
+
 static int _prctl(int option, unsigned long arg2, unsigned long arg3, unsigned long arg4,
 		  unsigned long arg5)
 {
@@ -78,8 +89,14 @@
 #define handle_error(msg) __handle_error(__FILE__, __LINE__, msg)
 static void __handle_error(char *fn, int ln, char *msg)
 {
+	int pidx;
 	printf("(%s:%d) - ", fn, ln);
 	perror(msg);
+	if (need_cleanup) {
+		for (pidx = 0; pidx < num_processes; ++pidx)
+			kill(procs[pidx].cpid, 15);
+		need_cleanup = 0;
+	}
 	exit(EXIT_FAILURE);
 }
 
@@ -106,13 +123,6 @@
 	return cookie;
 }
 
-struct child_args {
-	int num_threads;
-	int pfd[2];
-	int cpid;
-	int thr_tids[MAX_THREADS];
-};
-
 static int child_func_thread(void __attribute__((unused))*arg)
 {
 	while (1)
@@ -212,10 +222,7 @@
 
 int main(int argc, char *argv[])
 {
-	struct child_args procs[MAX_PROCESSES];
-
 	int keypress = 0;
-	int num_processes = 2;
 	int num_threads = 3;
 	int delay = 0;
 	int res = 0;
@@ -262,6 +269,7 @@
 
 	printf("\n## Create a thread/process/process group hiearchy\n");
 	create_processes(num_processes, num_threads, procs);
+	need_cleanup = 1;
 	disp_processes(num_processes, procs);
 	validate(get_cs_cookie(0) == 0);
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/seccomp/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/seccomp/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-CFLAGS += -Wl,-no-as-needed -Wall
+CFLAGS += -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/
 LDFLAGS += -lpthread
 
 TEST_GEN_PROGS := seccomp_bpf seccomp_benchmark
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/seccomp/seccomp_bpf.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/seccomp/seccomp_bpf.c
@@ -802,7 +802,7 @@
 		.len = (unsigned short)ARRAY_SIZE(filter_thread),
 		.filter = filter_thread,
 	};
-	int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
+	int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAA;
 	struct sock_filter filter_process[] = {
 		BPF_STMT(BPF_LD|BPF_W|BPF_ABS,
 			offsetof(struct seccomp_data, nr)),
@@ -955,7 +955,7 @@
 	ASSERT_EQ(0, ret);
 
 	EXPECT_EQ(parent, syscall(__NR_getppid));
-	EXPECT_EQ(-1, read(0, NULL, 0));
+	EXPECT_EQ(-1, read(-1, NULL, 0));
 	EXPECT_EQ(E2BIG, errno);
 }
 
@@ -974,7 +974,7 @@
 
 	EXPECT_EQ(parent, syscall(__NR_getppid));
 	/* "errno" of 0 is ok. */
-	EXPECT_EQ(0, read(0, NULL, 0));
+	EXPECT_EQ(0, read(-1, NULL, 0));
 }
 
 /*
@@ -995,7 +995,7 @@
 	ASSERT_EQ(0, ret);
 
 	EXPECT_EQ(parent, syscall(__NR_getppid));
-	EXPECT_EQ(-1, read(0, NULL, 0));
+	EXPECT_EQ(-1, read(-1, NULL, 0));
 	EXPECT_EQ(4095, errno);
 }
 
@@ -1026,7 +1026,7 @@
 	ASSERT_EQ(0, ret);
 
 	EXPECT_EQ(parent, syscall(__NR_getppid));
-	EXPECT_EQ(-1, read(0, NULL, 0));
+	EXPECT_EQ(-1, read(-1, NULL, 0));
 	EXPECT_EQ(12, errno);
 }
 
@@ -2579,7 +2579,7 @@
 	ret = prctl(PR_GET_NO_NEW_PRIVS, 0, 0, 0, 0);
 	if (!ret)
 		return (void *)SIBLING_EXIT_NEWPRIVS;
-	read(0, NULL, 0);
+	read(-1, NULL, 0);
 	return (void *)SIBLING_EXIT_UNKILLED;
 }
 
@@ -3975,18 +3975,17 @@
 	/* There may be arbitrary already-open fds at test start. */
 	memfd = memfd_create("test", 0);
 	ASSERT_GE(memfd, 0);
-	nextfd = memfd + 1;
 
 	ret = prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0);
 	ASSERT_EQ(0, ret) {
 		TH_LOG("Kernel does not support PR_SET_NO_NEW_PRIVS!");
 	}
 
-	/* fd: 4 */
 	/* Check that the basic notification machinery works */
 	listener = user_notif_syscall(__NR_getppid,
 				      SECCOMP_FILTER_FLAG_NEW_LISTENER);
-	ASSERT_EQ(listener, nextfd++);
+	ASSERT_GE(listener, 0);
+	nextfd = listener + 1;
 
 	pid = fork();
 	ASSERT_GE(pid, 0);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/seccomp/settings
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/seccomp/settings
@@ -1 +1 @@
-timeout=120
+timeout=300
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/sgx/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/sgx/Makefile
@@ -4,7 +4,7 @@
 
 .PHONY: all clean
 
-CAN_BUILD_X86_64 := $(shell ../x86/check_cc.sh $(CC) \
+CAN_BUILD_X86_64 := $(shell ../x86/check_cc.sh "$(CC)" \
 			    ../x86/trivial_64bit_program.c)
 
 ifndef OBJCOPY
@@ -16,9 +16,9 @@
 ENCL_CFLAGS := -Wall -Werror -static -nostdlib -nostartfiles -fPIC \
 	       -fno-stack-protector -mrdrnd $(INCLUDES)
 
+ifeq ($(CAN_BUILD_X86_64), 1)
 TEST_CUSTOM_PROGS := $(OUTPUT)/test_sgx
 
-ifeq ($(CAN_BUILD_X86_64), 1)
 all: $(TEST_CUSTOM_PROGS) $(OUTPUT)/test_encl.elf
 endif
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/sgx/sigstruct.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/sgx/sigstruct.c
@@ -310,9 +310,9 @@
 	struct sgx_sigstruct *sigstruct = &encl->sigstruct;
 	struct sgx_sigstruct_payload payload;
 	uint8_t digest[SHA256_DIGEST_LENGTH];
+	EVP_MD_CTX *ctx = NULL;
 	unsigned int siglen;
 	RSA *key = NULL;
-	EVP_MD_CTX *ctx;
 	int i;
 
 	memset(sigstruct, 0, sizeof(*sigstruct));
@@ -376,7 +376,8 @@
 	return true;
 
 err:
-	EVP_MD_CTX_destroy(ctx);
+	if (ctx)
+		EVP_MD_CTX_destroy(ctx);
 	RSA_free(key);
 	return false;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/sgx/test_encl.lds
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/sgx/test_encl.lds
@@ -34,8 +34,4 @@
 	}
 }
 
-ASSERT(!DEFINED(.altinstructions), "ALTERNATIVES are not supported in enclaves")
-ASSERT(!DEFINED(.altinstr_replacement), "ALTERNATIVES are not supported in enclaves")
-ASSERT(!DEFINED(.discard.retpoline_safe), "RETPOLINE ALTERNATIVES are not supported in enclaves")
-ASSERT(!DEFINED(.discard.nospec), "RETPOLINE ALTERNATIVES are not supported in enclaves")
-ASSERT(!DEFINED(.got.plt), "Libcalls are not supported in enclaves")
+ASSERT(!DEFINED(_GLOBAL_OFFSET_TABLE_), "Libcalls through GOT are not supported in enclaves")
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/sigaltstack/current_stack_pointer.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/sigaltstack/current_stack_pointer.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#if __alpha__
+register unsigned long sp asm("$30");
+#elif __arm__ || __aarch64__ || __csky__ || __m68k__ || __mips__ || __riscv
+register unsigned long sp asm("sp");
+#elif __i386__
+register unsigned long sp asm("esp");
+#elif __loongarch64
+register unsigned long sp asm("$sp");
+#elif __powerpc__
+register unsigned long sp asm("r1");
+#elif __s390x__
+register unsigned long sp asm("%15");
+#elif __sh__
+register unsigned long sp asm("r15");
+#elif __x86_64__
+register unsigned long sp asm("rsp");
+#elif __XTENSA__
+register unsigned long sp asm("a1");
+#else
+#error "implement current_stack_pointer equivalent"
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/sigaltstack/sas.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/sigaltstack/sas.c
@@ -20,6 +20,7 @@
 #include <sys/auxv.h>
 
 #include "../kselftest.h"
+#include "current_stack_pointer.h"
 
 #ifndef SS_AUTODISARM
 #define SS_AUTODISARM  (1U << 31)
@@ -46,12 +47,6 @@
 	stack_t stk;
 	struct stk_data *p;
 
-#if __s390x__
-	register unsigned long sp asm("%15");
-#else
-	register unsigned long sp asm("sp");
-#endif
-
 	if (sp < (unsigned long)sstack ||
 			sp >= (unsigned long)sstack + stack_size) {
 		ksft_exit_fail_msg("SP is not on sigaltstack\n");
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/syscall_user_dispatch/sud_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/syscall_user_dispatch/sud_test.c
@@ -158,6 +158,20 @@
 
 	/* In preparation for sigreturn. */
 	SYSCALL_DISPATCH_OFF(glob_sel);
+
+	/*
+	 * The tests for argument handling assume that `syscall(x) == x`. This
+	 * is a NOP on x86 because the syscall number is passed in %rax, which
+	 * happens to also be the function ABI return register.  Other
+	 * architectures may need to swizzle the arguments around.
+	 */
+#if defined(__riscv)
+/* REG_A7 is not defined in libc headers */
+# define REG_A7 (REG_A0 + 7)
+
+	((ucontext_t *)ucontext)->uc_mcontext.__gregs[REG_A0] =
+			((ucontext_t *)ucontext)->uc_mcontext.__gregs[REG_A7];
+#endif
 }
 
 TEST(dispatch_and_return)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/tc-testing/config
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/tc-testing/config
@@ -5,6 +5,8 @@
 CONFIG_NF_CONNTRACK_MARK=y
 CONFIG_NF_CONNTRACK_ZONES=y
 CONFIG_NF_CONNTRACK_LABELS=y
+CONFIG_NF_CONNTRACK_PROCFS=y
+CONFIG_NF_FLOW_TABLE=m
 CONFIG_NF_NAT=m
 
 CONFIG_NET_SCHED=y
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/tc-testing/settings
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/tc-testing/settings
@@ -0,0 +1 @@
+timeout=900
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/tc-testing/tdc.py
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/tc-testing/tdc.py
@@ -129,7 +129,6 @@
             except Exception as ee:
                 print('exception {} in call to pre_case for {} plugin'.
                       format(ee, pgn_inst.__class__))
-                print('test_ordinal is {}'.format(test_ordinal))
                 print('testid is {}'.format(caseinfo['id']))
                 raise
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/timers/clocksource-switch.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/timers/clocksource-switch.c
@@ -110,10 +110,10 @@
 
 	sprintf(buf, "./inconsistency-check -t %i", secs);
 	ret = system(buf);
-	if (ret)
-		return ret;
+	if (WIFEXITED(ret) && WEXITSTATUS(ret))
+		return WEXITSTATUS(ret);
 	ret = system("./nanosleep");
-	return ret;
+	return WIFEXITED(ret) ? WEXITSTATUS(ret) : 0;
 }
 
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/timers/posix_timers.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/timers/posix_timers.c
@@ -66,7 +66,7 @@
 	diff = end.tv_usec - start.tv_usec;
 	diff += (end.tv_sec - start.tv_sec) * USECS_PER_SEC;
 
-	if (abs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) {
+	if (llabs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) {
 		printf("Diff too high: %lld..", diff);
 		return -1;
 	}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/timers/rtcpie.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/timers/rtcpie.c
@@ -111,11 +111,11 @@
 			timersub(&end, &start, &diff);
 			if (diff.tv_sec > 0 ||
 			    diff.tv_usec > ((1000000L / tmp) * 1.10)) {
-				fprintf(stderr, "\nPIE delta error: %ld.%06ld should be close to 0.%06ld\n",
+				fprintf(stderr, "\nUbuntu Testing Force Pass LP #1814234: PIE delta error: %ld.%06ld should be close to 0.%06ld\n",
 				       diff.tv_sec, diff.tv_usec,
 				       (1000000L / tmp));
 				fflush(stdout);
-				exit(-1);
+				break; // LP: #1814234
 			}
 
 			fprintf(stderr, " %d",i);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/timers/valid-adjtimex.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/timers/valid-adjtimex.c
@@ -21,9 +21,6 @@
  *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *   GNU General Public License for more details.
  */
-
-
-
 #include <stdio.h>
 #include <stdlib.h>
 #include <time.h>
@@ -40,7 +37,7 @@
 #define ADJ_SETOFFSET 0x0100
 
 #include <sys/syscall.h>
-static int clock_adjtime(clockid_t id, struct timex *tx)
+int clock_adjtime(clockid_t id, struct timex *tx)
 {
 	return syscall(__NR_clock_adjtime, id, tx);
 }
@@ -62,45 +59,47 @@
 #define NUM_FREQ_OUTOFRANGE 4
 #define NUM_FREQ_INVALID 2
 
+#define SHIFTED_PPM (1 << 16)
+
 long valid_freq[NUM_FREQ_VALID] = {
-	-499<<16,
-	-450<<16,
-	-400<<16,
-	-350<<16,
-	-300<<16,
-	-250<<16,
-	-200<<16,
-	-150<<16,
-	-100<<16,
-	-75<<16,
-	-50<<16,
-	-25<<16,
-	-10<<16,
-	-5<<16,
-	-1<<16,
+	 -499 * SHIFTED_PPM,
+	 -450 * SHIFTED_PPM,
+	 -400 * SHIFTED_PPM,
+	 -350 * SHIFTED_PPM,
+	 -300 * SHIFTED_PPM,
+	 -250 * SHIFTED_PPM,
+	 -200 * SHIFTED_PPM,
+	 -150 * SHIFTED_PPM,
+	 -100 * SHIFTED_PPM,
+	  -75 * SHIFTED_PPM,
+	  -50 * SHIFTED_PPM,
+	  -25 * SHIFTED_PPM,
+	  -10 * SHIFTED_PPM,
+	   -5 * SHIFTED_PPM,
+	   -1 * SHIFTED_PPM,
 	-1000,
-	1<<16,
-	5<<16,
-	10<<16,
-	25<<16,
-	50<<16,
-	75<<16,
-	100<<16,
-	150<<16,
-	200<<16,
-	250<<16,
-	300<<16,
-	350<<16,
-	400<<16,
-	450<<16,
-	499<<16,
+	    1 * SHIFTED_PPM,
+	    5 * SHIFTED_PPM,
+	   10 * SHIFTED_PPM,
+	   25 * SHIFTED_PPM,
+	   50 * SHIFTED_PPM,
+	   75 * SHIFTED_PPM,
+	  100 * SHIFTED_PPM,
+	  150 * SHIFTED_PPM,
+	  200 * SHIFTED_PPM,
+	  250 * SHIFTED_PPM,
+	  300 * SHIFTED_PPM,
+	  350 * SHIFTED_PPM,
+	  400 * SHIFTED_PPM,
+	  450 * SHIFTED_PPM,
+	  499 * SHIFTED_PPM,
 };
 
 long outofrange_freq[NUM_FREQ_OUTOFRANGE] = {
-	-1000<<16,
-	-550<<16,
-	550<<16,
-	1000<<16,
+	-1000 * SHIFTED_PPM,
+	 -550 * SHIFTED_PPM,
+	  550 * SHIFTED_PPM,
+	 1000 * SHIFTED_PPM,
 };
 
 #define LONG_MAX (~0UL>>1)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/tpm2/tpm2.py
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/tpm2/tpm2.py
@@ -370,6 +370,10 @@
             fcntl.fcntl(self.tpm, fcntl.F_SETFL, flags)
             self.tpm_poll = select.poll()
 
+    def __del__(self):
+        if self.tpm:
+            self.tpm.close()
+
     def close(self):
         self.tpm.close()
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vDSO/parse_vdso.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vDSO/parse_vdso.c
@@ -36,6 +36,12 @@
 #define ELF_BITS_XFORM(bits, x) ELF_BITS_XFORM2(bits, x)
 #define ELF(x) ELF_BITS_XFORM(ELF_BITS, x)
 
+#ifdef __s390x__
+#define ELF_HASH_ENTRY ELF(Xword)
+#else
+#define ELF_HASH_ENTRY ELF(Word)
+#endif
+
 static struct vdso_info
 {
 	bool valid;
@@ -47,22 +53,28 @@
 	/* Symbol table */
 	ELF(Sym) *symtab;
 	const char *symstrings;
-	ELF(Word) *bucket, *chain;
-	ELF(Word) nbucket, nchain;
+	ELF_HASH_ENTRY *bucket, *chain;
+	ELF_HASH_ENTRY nbucket, nchain;
 
 	/* Version table */
 	ELF(Versym) *versym;
 	ELF(Verdef) *verdef;
 } vdso_info;
 
-/* Straight from the ELF specification. */
-static unsigned long elf_hash(const unsigned char *name)
+/*
+ * Straight from the ELF specification...and then tweaked slightly, in order to
+ * avoid a few clang warnings.
+ */
+static unsigned long elf_hash(const char *name)
 {
 	unsigned long h = 0, g;
-	while (*name)
+	const unsigned char *uch_name = (const unsigned char *)name;
+
+	while (*uch_name)
 	{
-		h = (h << 4) + *name++;
-		if (g = h & 0xf0000000)
+		h = (h << 4) + *uch_name++;
+		g = h & 0xf0000000;
+		if (g)
 			h ^= g >> 24;
 		h &= ~g;
 	}
@@ -109,7 +121,7 @@
 	/*
 	 * Fish out the useful bits of the dynamic table.
 	 */
-	ELF(Word) *hash = 0;
+	ELF_HASH_ENTRY *hash = 0;
 	vdso_info.symstrings = 0;
 	vdso_info.symtab = 0;
 	vdso_info.versym = 0;
@@ -127,7 +139,7 @@
 				 + vdso_info.load_offset);
 			break;
 		case DT_HASH:
-			hash = (ELF(Word) *)
+			hash = (ELF_HASH_ENTRY *)
 				((uintptr_t)dyn[i].d_un.d_ptr
 				 + vdso_info.load_offset);
 			break;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vDSO/vdso_config.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vDSO/vdso_config.h
@@ -18,18 +18,18 @@
 #elif defined(__aarch64__)
 #define VDSO_VERSION		3
 #define VDSO_NAMES		0
-#elif defined(__powerpc__)
+#elif defined(__powerpc64__)
 #define VDSO_VERSION		1
 #define VDSO_NAMES		0
-#define VDSO_32BIT		1
-#elif defined(__powerpc64__)
+#elif defined(__powerpc__)
 #define VDSO_VERSION		1
 #define VDSO_NAMES		0
-#elif defined (__s390__)
+#define VDSO_32BIT		1
+#elif defined (__s390__) && !defined(__s390x__)
 #define VDSO_VERSION		2
 #define VDSO_NAMES		0
 #define VDSO_32BIT		1
-#elif defined (__s390X__)
+#elif defined (__s390x__)
 #define VDSO_VERSION		2
 #define VDSO_NAMES		0
 #elif defined(__mips__)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vDSO/vdso_standalone_test_x86.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vDSO/vdso_standalone_test_x86.c
@@ -18,7 +18,7 @@
 
 #include "parse_vdso.h"
 
-/* We need a libc functions... */
+/* We need some libc functions... */
 int strcmp(const char *a, const char *b)
 {
 	/* This implementation is buggy: it never returns -1. */
@@ -34,6 +34,20 @@
 	return 0;
 }
 
+/*
+ * The clang build needs this, although gcc does not.
+ * Stolen from lib/string.c.
+ */
+void *memcpy(void *dest, const void *src, size_t count)
+{
+	char *tmp = dest;
+	const char *s = src;
+
+	while (count--)
+		*tmp++ = *s++;
+	return dest;
+}
+
 /* ...and two syscalls.  This is x86-specific. */
 static inline long x86_syscall3(long nr, long a0, long a1, long a2)
 {
@@ -70,7 +84,7 @@
 	}
 }
 
-__attribute__((externally_visible)) void c_main(void **stack)
+void c_main(void **stack)
 {
 	/* Parse the stack */
 	long argc = (long)*stack;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vDSO/vdso_test_abi.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vDSO/vdso_test_abi.c
@@ -33,110 +33,114 @@
 typedef long (*vdso_clock_getres_t)(clockid_t clk_id, struct timespec *ts);
 typedef time_t (*vdso_time_t)(time_t *t);
 
-static int vdso_test_gettimeofday(void)
+#define VDSO_TEST_PASS_MSG()	"\n%s(): PASS\n", __func__
+#define VDSO_TEST_FAIL_MSG(x)	"\n%s(): %s FAIL\n", __func__, x
+#define VDSO_TEST_SKIP_MSG(x)	"\n%s(): SKIP: Could not find %s\n", __func__, x
+
+static void vdso_test_gettimeofday(void)
 {
 	/* Find gettimeofday. */
 	vdso_gettimeofday_t vdso_gettimeofday =
 		(vdso_gettimeofday_t)vdso_sym(version, name[0]);
 
 	if (!vdso_gettimeofday) {
-		printf("Could not find %s\n", name[0]);
-		return KSFT_SKIP;
+		ksft_test_result_skip(VDSO_TEST_SKIP_MSG(name[0]));
+		return;
 	}
 
 	struct timeval tv;
 	long ret = vdso_gettimeofday(&tv, 0);
 
 	if (ret == 0) {
-		printf("The time is %lld.%06lld\n",
-		       (long long)tv.tv_sec, (long long)tv.tv_usec);
+		ksft_print_msg("The time is %lld.%06lld\n",
+			       (long long)tv.tv_sec, (long long)tv.tv_usec);
+		ksft_test_result_pass(VDSO_TEST_PASS_MSG());
 	} else {
-		printf("%s failed\n", name[0]);
-		return KSFT_FAIL;
+		ksft_test_result_fail(VDSO_TEST_FAIL_MSG(name[0]));
 	}
-
-	return KSFT_PASS;
 }
 
-static int vdso_test_clock_gettime(clockid_t clk_id)
+static void vdso_test_clock_gettime(clockid_t clk_id)
 {
 	/* Find clock_gettime. */
 	vdso_clock_gettime_t vdso_clock_gettime =
 		(vdso_clock_gettime_t)vdso_sym(version, name[1]);
 
 	if (!vdso_clock_gettime) {
-		printf("Could not find %s\n", name[1]);
-		return KSFT_SKIP;
+		ksft_test_result_skip(VDSO_TEST_SKIP_MSG(name[1]));
+		return;
 	}
 
 	struct timespec ts;
 	long ret = vdso_clock_gettime(clk_id, &ts);
 
 	if (ret == 0) {
-		printf("The time is %lld.%06lld\n",
-		       (long long)ts.tv_sec, (long long)ts.tv_nsec);
+		ksft_print_msg("The time is %lld.%06lld\n",
+			       (long long)ts.tv_sec, (long long)ts.tv_nsec);
+		ksft_test_result_pass(VDSO_TEST_PASS_MSG());
 	} else {
-		printf("%s failed\n", name[1]);
-		return KSFT_FAIL;
+		ksft_test_result_fail(VDSO_TEST_FAIL_MSG(name[1]));
 	}
-
-	return KSFT_PASS;
 }
 
-static int vdso_test_time(void)
+static void vdso_test_time(void)
 {
 	/* Find time. */
 	vdso_time_t vdso_time =
 		(vdso_time_t)vdso_sym(version, name[2]);
 
 	if (!vdso_time) {
-		printf("Could not find %s\n", name[2]);
-		return KSFT_SKIP;
+		ksft_test_result_skip(VDSO_TEST_SKIP_MSG(name[2]));
+		return;
 	}
 
 	long ret = vdso_time(NULL);
 
 	if (ret > 0) {
-		printf("The time in hours since January 1, 1970 is %lld\n",
+		ksft_print_msg("The time in hours since January 1, 1970 is %lld\n",
 				(long long)(ret / 3600));
+		ksft_test_result_pass(VDSO_TEST_PASS_MSG());
 	} else {
-		printf("%s failed\n", name[2]);
-		return KSFT_FAIL;
+		ksft_test_result_fail(VDSO_TEST_FAIL_MSG(name[2]));
 	}
-
-	return KSFT_PASS;
 }
 
-static int vdso_test_clock_getres(clockid_t clk_id)
+static void vdso_test_clock_getres(clockid_t clk_id)
 {
+	int clock_getres_fail = 0;
+
 	/* Find clock_getres. */
 	vdso_clock_getres_t vdso_clock_getres =
 		(vdso_clock_getres_t)vdso_sym(version, name[3]);
 
 	if (!vdso_clock_getres) {
-		printf("Could not find %s\n", name[3]);
-		return KSFT_SKIP;
+		ksft_test_result_skip(VDSO_TEST_SKIP_MSG(name[3]));
+		return;
 	}
 
 	struct timespec ts, sys_ts;
 	long ret = vdso_clock_getres(clk_id, &ts);
 
 	if (ret == 0) {
-		printf("The resolution is %lld %lld\n",
-		       (long long)ts.tv_sec, (long long)ts.tv_nsec);
+		ksft_print_msg("The vdso resolution is %lld %lld\n",
+			       (long long)ts.tv_sec, (long long)ts.tv_nsec);
 	} else {
-		printf("%s failed\n", name[3]);
-		return KSFT_FAIL;
+		clock_getres_fail++;
 	}
 
 	ret = syscall(SYS_clock_getres, clk_id, &sys_ts);
 
-	if ((sys_ts.tv_sec != ts.tv_sec) || (sys_ts.tv_nsec != ts.tv_nsec)) {
-		printf("%s failed\n", name[3]);
-		return KSFT_FAIL;
-	}
+	ksft_print_msg("The syscall resolution is %lld %lld\n",
+			(long long)sys_ts.tv_sec, (long long)sys_ts.tv_nsec);
 
-	return KSFT_PASS;
+	if ((sys_ts.tv_sec != ts.tv_sec) || (sys_ts.tv_nsec != ts.tv_nsec))
+		clock_getres_fail++;
+
+	if (clock_getres_fail > 0) {
+		ksft_test_result_fail(VDSO_TEST_FAIL_MSG(name[3]));
+	} else {
+		ksft_test_result_pass(VDSO_TEST_PASS_MSG());
+	}
 }
 
 const char *vdso_clock_name[12] = {
@@ -158,36 +162,23 @@
  * This function calls vdso_test_clock_gettime and vdso_test_clock_getres
  * with different values for clock_id.
  */
-static inline int vdso_test_clock(clockid_t clock_id)
+static inline void vdso_test_clock(clockid_t clock_id)
 {
-	int ret0, ret1;
-
-	ret0 = vdso_test_clock_gettime(clock_id);
-	/* A skipped test is considered passed */
-	if (ret0 == KSFT_SKIP)
-		ret0 = KSFT_PASS;
-
-	ret1 = vdso_test_clock_getres(clock_id);
-	/* A skipped test is considered passed */
-	if (ret1 == KSFT_SKIP)
-		ret1 = KSFT_PASS;
+	ksft_print_msg("\nclock_id: %s\n", vdso_clock_name[clock_id]);
 
-	ret0 += ret1;
+	vdso_test_clock_gettime(clock_id);
 
-	printf("clock_id: %s", vdso_clock_name[clock_id]);
-
-	if (ret0 > 0)
-		printf(" [FAIL]\n");
-	else
-		printf(" [PASS]\n");
-
-	return ret0;
+	vdso_test_clock_getres(clock_id);
 }
 
+#define VDSO_TEST_PLAN	16
+
 int main(int argc, char **argv)
 {
 	unsigned long sysinfo_ehdr = getauxval(AT_SYSINFO_EHDR);
-	int ret;
+
+	ksft_print_header();
+	ksft_set_plan(VDSO_TEST_PLAN);
 
 	if (!sysinfo_ehdr) {
 		printf("AT_SYSINFO_EHDR is not present!\n");
@@ -201,44 +192,42 @@
 
 	vdso_init_from_sysinfo_ehdr(getauxval(AT_SYSINFO_EHDR));
 
-	ret = vdso_test_gettimeofday();
+	vdso_test_gettimeofday();
 
 #if _POSIX_TIMERS > 0
 
 #ifdef CLOCK_REALTIME
-	ret += vdso_test_clock(CLOCK_REALTIME);
+	vdso_test_clock(CLOCK_REALTIME);
 #endif
 
 #ifdef CLOCK_BOOTTIME
-	ret += vdso_test_clock(CLOCK_BOOTTIME);
+	vdso_test_clock(CLOCK_BOOTTIME);
 #endif
 
 #ifdef CLOCK_TAI
-	ret += vdso_test_clock(CLOCK_TAI);
+	vdso_test_clock(CLOCK_TAI);
 #endif
 
 #ifdef CLOCK_REALTIME_COARSE
-	ret += vdso_test_clock(CLOCK_REALTIME_COARSE);
+	vdso_test_clock(CLOCK_REALTIME_COARSE);
 #endif
 
 #ifdef CLOCK_MONOTONIC
-	ret += vdso_test_clock(CLOCK_MONOTONIC);
+	vdso_test_clock(CLOCK_MONOTONIC);
 #endif
 
 #ifdef CLOCK_MONOTONIC_RAW
-	ret += vdso_test_clock(CLOCK_MONOTONIC_RAW);
+	vdso_test_clock(CLOCK_MONOTONIC_RAW);
 #endif
 
 #ifdef CLOCK_MONOTONIC_COARSE
-	ret += vdso_test_clock(CLOCK_MONOTONIC_COARSE);
+	vdso_test_clock(CLOCK_MONOTONIC_COARSE);
 #endif
 
 #endif
 
-	ret += vdso_test_time();
-
-	if (ret > 0)
-		return KSFT_FAIL;
+	vdso_test_time();
 
-	return KSFT_PASS;
+	ksft_print_cnts();
+	return ksft_get_fail_cnt() == 0 ? KSFT_PASS : KSFT_FAIL;
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vDSO/vdso_test_clock_getres.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vDSO/vdso_test_clock_getres.c
@@ -84,12 +84,12 @@
 
 int main(int argc, char **argv)
 {
-	int ret;
+	int ret = 0;
 
 #if _POSIX_TIMERS > 0
 
 #ifdef CLOCK_REALTIME
-	ret = vdso_test_clock(CLOCK_REALTIME);
+	ret += vdso_test_clock(CLOCK_REALTIME);
 #endif
 
 #ifdef CLOCK_BOOTTIME
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vDSO/vdso_test_correctness.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vDSO/vdso_test_correctness.c
@@ -113,6 +113,12 @@
 	if (!vdso)
 		vdso = dlopen("linux-gate.so.1",
 			      RTLD_LAZY | RTLD_LOCAL | RTLD_NOLOAD);
+	if (!vdso)
+		vdso = dlopen("linux-vdso32.so.1",
+			      RTLD_LAZY | RTLD_LOCAL | RTLD_NOLOAD);
+	if (!vdso)
+		vdso = dlopen("linux-vdso64.so.1",
+			      RTLD_LAZY | RTLD_LOCAL | RTLD_NOLOAD);
 	if (!vdso) {
 		printf("[WARN]\tfailed to find vDSO\n");
 		return;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/Makefile
@@ -1,6 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 # Makefile for vm selftests
 
+LOCAL_HDRS += $(selfdir)/vm/local_config.h $(top_srcdir)/mm/gup_test.h
+
 include local_config.mk
 
 uname_M := $(shell uname -m 2>/dev/null || echo not)
@@ -48,13 +50,13 @@
 TEST_GEN_FILES += ksm_tests
 
 ifeq ($(MACHINE),x86_64)
-CAN_BUILD_I386 := $(shell ./../x86/check_cc.sh $(CC) ../x86/trivial_32bit_program.c -m32)
-CAN_BUILD_X86_64 := $(shell ./../x86/check_cc.sh $(CC) ../x86/trivial_64bit_program.c)
-CAN_BUILD_WITH_NOPIE := $(shell ./../x86/check_cc.sh $(CC) ../x86/trivial_program.c -no-pie)
-
-TARGETS := protection_keys
-BINARIES_32 := $(TARGETS:%=%_32)
-BINARIES_64 := $(TARGETS:%=%_64)
+CAN_BUILD_I386 := $(shell ./../x86/check_cc.sh "$(CC)" ../x86/trivial_32bit_program.c -m32)
+CAN_BUILD_X86_64 := $(shell ./../x86/check_cc.sh "$(CC)" ../x86/trivial_64bit_program.c)
+CAN_BUILD_WITH_NOPIE := $(shell ./../x86/check_cc.sh "$(CC)" ../x86/trivial_program.c -no-pie)
+
+VMTARGETS := protection_keys
+BINARIES_32 := $(VMTARGETS:%=%_32)
+BINARIES_64 := $(VMTARGETS:%=%_64)
 
 ifeq ($(CAN_BUILD_WITH_NOPIE),1)
 CFLAGS += -no-pie
@@ -107,7 +109,7 @@
 $(BINARIES_32): LDLIBS += -lrt -ldl -lm
 $(BINARIES_32): $(OUTPUT)/%_32: %.c
 	$(CC) $(CFLAGS) $(EXTRA_CFLAGS) $(notdir $^) $(LDLIBS) -o $@
-$(foreach t,$(TARGETS),$(eval $(call gen-target-rule-32,$(t))))
+$(foreach t,$(VMTARGETS),$(eval $(call gen-target-rule-32,$(t))))
 endif
 
 ifeq ($(CAN_BUILD_X86_64),1)
@@ -115,7 +117,7 @@
 $(BINARIES_64): LDLIBS += -lrt -ldl
 $(BINARIES_64): $(OUTPUT)/%_64: %.c
 	$(CC) $(CFLAGS) $(EXTRA_CFLAGS) $(notdir $^) $(LDLIBS) -o $@
-$(foreach t,$(TARGETS),$(eval $(call gen-target-rule-64,$(t))))
+$(foreach t,$(VMTARGETS),$(eval $(call gen-target-rule-64,$(t))))
 endif
 
 # x86_64 users should be encouraged to install 32-bit libraries
@@ -139,10 +141,6 @@
 
 $(OUTPUT)/mlock-random-test $(OUTPUT)/memfd_secret: LDLIBS += -lcap
 
-$(OUTPUT)/gup_test: ../../../../mm/gup_test.h
-
-$(OUTPUT)/hmm-tests: local_config.h
-
 # HMM_EXTRA_LIBS may get set in local_config.mk, or it may be left empty.
 $(OUTPUT)/hmm-tests: LDLIBS += $(HMM_EXTRA_LIBS)
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/charge_reserved_hugetlb.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/charge_reserved_hugetlb.sh
@@ -1,4 +1,4 @@
-#!/bin/sh
+#!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
 # Kselftest framework requirement - SKIP code is 4.
@@ -24,19 +24,23 @@
   reservation_usage_file=rsvd.current
 fi
 
-cgroup_path=/dev/cgroup/memory
-if [[ ! -e $cgroup_path ]]; then
-  mkdir -p $cgroup_path
-  if [[ $cgroup2 ]]; then
+if [[ $cgroup2 ]]; then
+  cgroup_path=$(mount -t cgroup2 | head -1 | awk '{print $3}')
+  if [[ -z "$cgroup_path" ]]; then
+    cgroup_path=/dev/cgroup/memory
     mount -t cgroup2 none $cgroup_path
-  else
+    do_umount=1
+  fi
+  echo "+hugetlb" >$cgroup_path/cgroup.subtree_control
+else
+  cgroup_path=$(mount -t cgroup | grep ",hugetlb" | awk '{print $3}')
+  if [[ -z "$cgroup_path" ]]; then
+    cgroup_path=/dev/cgroup/memory
     mount -t cgroup memory,hugetlb $cgroup_path
+    do_umount=1
   fi
 fi
-
-if [[ $cgroup2 ]]; then
-  echo "+hugetlb" >/dev/cgroup/memory/cgroup.subtree_control
-fi
+export cgroup_path
 
 function cleanup() {
   if [[ $cgroup2 ]]; then
@@ -108,7 +112,7 @@
 
 function wait_for_hugetlb_memory_to_get_depleted() {
   local cgroup="$1"
-  local path="/dev/cgroup/memory/$cgroup/hugetlb.${MB}MB.$reservation_usage_file"
+  local path="$cgroup_path/$cgroup/hugetlb.${MB}MB.$reservation_usage_file"
   # Wait for hugetlbfs memory to get depleted.
   while [ $(cat $path) != 0 ]; do
     echo Waiting for hugetlb memory to get depleted.
@@ -121,7 +125,7 @@
   local cgroup="$1"
   local size="$2"
 
-  local path="/dev/cgroup/memory/$cgroup/hugetlb.${MB}MB.$reservation_usage_file"
+  local path="$cgroup_path/$cgroup/hugetlb.${MB}MB.$reservation_usage_file"
   # Wait for hugetlbfs memory to get written.
   while [ $(cat $path) != $size ]; do
     echo Waiting for hugetlb memory reservation to reach size $size.
@@ -134,7 +138,7 @@
   local cgroup="$1"
   local size="$2"
 
-  local path="/dev/cgroup/memory/$cgroup/hugetlb.${MB}MB.$fault_usage_file"
+  local path="$cgroup_path/$cgroup/hugetlb.${MB}MB.$fault_usage_file"
   # Wait for hugetlbfs memory to get written.
   while [ $(cat $path) != $size ]; do
     echo Waiting for hugetlb memory to reach size $size.
@@ -248,7 +252,7 @@
   local cgroup="$1"
   if [[ "$(pgrep -f write_to_hugetlbfs)" != "" ]]; then
     echo killing write_to_hugetlbfs
-    killall -2 write_to_hugetlbfs
+    killall -2 --wait write_to_hugetlbfs
     wait_for_hugetlb_memory_to_get_depleted $cgroup
   fi
   set -e
@@ -574,5 +578,7 @@
   done     # populate
 done       # method
 
-umount $cgroup_path
-rmdir $cgroup_path
+if [[ $do_umount ]]; then
+  umount $cgroup_path
+  rmdir $cgroup_path
+fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/compaction_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/compaction_test.c
@@ -33,7 +33,7 @@
 	FILE *cmdfile = popen(cmd, "r");
 
 	if (!(fgets(buffer, sizeof(buffer), cmdfile))) {
-		perror("Failed to read meminfo\n");
+		ksft_print_msg("Failed to read meminfo: %s\n", strerror(errno));
 		return -1;
 	}
 
@@ -44,7 +44,7 @@
 	cmdfile = popen(cmd, "r");
 
 	if (!(fgets(buffer, sizeof(buffer), cmdfile))) {
-		perror("Failed to read meminfo\n");
+		ksft_print_msg("Failed to read meminfo: %s\n", strerror(errno));
 		return -1;
 	}
 
@@ -62,14 +62,14 @@
 	fd = open("/proc/sys/vm/compact_unevictable_allowed",
 		  O_RDONLY | O_NONBLOCK);
 	if (fd < 0) {
-		perror("Failed to open\n"
-		       "/proc/sys/vm/compact_unevictable_allowed\n");
+		ksft_print_msg("Failed to open /proc/sys/vm/compact_unevictable_allowed: %s\n",
+			       strerror(errno));
 		return -1;
 	}
 
 	if (read(fd, &allowed, sizeof(char)) != sizeof(char)) {
-		perror("Failed to read from\n"
-		       "/proc/sys/vm/compact_unevictable_allowed\n");
+		ksft_print_msg("Failed to read from /proc/sys/vm/compact_unevictable_allowed: %s\n",
+			       strerror(errno));
 		close(fd);
 		return -1;
 	}
@@ -78,15 +78,17 @@
 	if (allowed == '1')
 		return 0;
 
+	ksft_print_msg("Compaction isn't allowed\n");
 	return -1;
 }
 
-int check_compaction(unsigned long mem_free, unsigned int hugepage_size)
+int check_compaction(unsigned long mem_free, unsigned long hugepage_size)
 {
-	int fd;
+	unsigned long nr_hugepages_ul;
+	int fd, ret = -1;
 	int compaction_index = 0;
-	char initial_nr_hugepages[10] = {0};
-	char nr_hugepages[10] = {0};
+	char initial_nr_hugepages[20] = {0};
+	char nr_hugepages[20] = {0};
 
 	/* We want to test with 80% of available memory. Else, OOM killer comes
 	   in to play */
@@ -94,18 +96,23 @@
 
 	fd = open("/proc/sys/vm/nr_hugepages", O_RDWR | O_NONBLOCK);
 	if (fd < 0) {
-		perror("Failed to open /proc/sys/vm/nr_hugepages");
+		ksft_test_result_fail("Failed to open /proc/sys/vm/nr_hugepages: %s\n",
+				      strerror(errno));
 		return -1;
 	}
 
 	if (read(fd, initial_nr_hugepages, sizeof(initial_nr_hugepages)) <= 0) {
-		perror("Failed to read from /proc/sys/vm/nr_hugepages");
+		ksft_test_result_fail("Failed to read from /proc/sys/vm/nr_hugepages: %s\n",
+				      strerror(errno));
 		goto close_fd;
 	}
 
+	lseek(fd, 0, SEEK_SET);
+
 	/* Start with the initial condition of 0 huge pages*/
 	if (write(fd, "0", sizeof(char)) != sizeof(char)) {
-		perror("Failed to write 0 to /proc/sys/vm/nr_hugepages\n");
+		ksft_test_result_fail("Failed to write 0 to /proc/sys/vm/nr_hugepages: %s\n",
+				      strerror(errno));
 		goto close_fd;
 	}
 
@@ -114,82 +121,80 @@
 	/* Request a large number of huge pages. The Kernel will allocate
 	   as much as it can */
 	if (write(fd, "100000", (6*sizeof(char))) != (6*sizeof(char))) {
-		perror("Failed to write 100000 to /proc/sys/vm/nr_hugepages\n");
+		ksft_test_result_fail("Failed to write 100000 to /proc/sys/vm/nr_hugepages: %s\n",
+				      strerror(errno));
 		goto close_fd;
 	}
 
 	lseek(fd, 0, SEEK_SET);
 
 	if (read(fd, nr_hugepages, sizeof(nr_hugepages)) <= 0) {
-		perror("Failed to re-read from /proc/sys/vm/nr_hugepages\n");
+		ksft_test_result_fail("Failed to re-read from /proc/sys/vm/nr_hugepages: %s\n",
+				      strerror(errno));
 		goto close_fd;
 	}
 
 	/* We should have been able to request at least 1/3 rd of the memory in
 	   huge pages */
-	compaction_index = mem_free/(atoi(nr_hugepages) * hugepage_size);
-
-	if (compaction_index > 3) {
-		printf("No of huge pages allocated = %d\n",
-		       (atoi(nr_hugepages)));
-		fprintf(stderr, "ERROR: Less that 1/%d of memory is available\n"
-			"as huge pages\n", compaction_index);
+	nr_hugepages_ul = strtoul(nr_hugepages, NULL, 10);
+	if (!nr_hugepages_ul) {
+		ksft_print_msg("ERROR: No memory is available as huge pages\n");
 		goto close_fd;
 	}
-
-	printf("No of huge pages allocated = %d\n",
-	       (atoi(nr_hugepages)));
+	compaction_index = mem_free/(nr_hugepages_ul * hugepage_size);
 
 	lseek(fd, 0, SEEK_SET);
 
 	if (write(fd, initial_nr_hugepages, strlen(initial_nr_hugepages))
 	    != strlen(initial_nr_hugepages)) {
-		perror("Failed to write value to /proc/sys/vm/nr_hugepages\n");
+		ksft_test_result_fail("Failed to write value to /proc/sys/vm/nr_hugepages: %s\n",
+				      strerror(errno));
 		goto close_fd;
 	}
 
-	close(fd);
-	return 0;
+	if (compaction_index > 3) {
+		ksft_print_msg("ERROR: Less than 1/%d of memory is available\n"
+			       "as huge pages\n", compaction_index);
+		ksft_test_result_fail("No of huge pages allocated = %d\n", (atoi(nr_hugepages)));
+		goto close_fd;
+	}
+
+	ksft_test_result_pass("Memory compaction succeeded. No of huge pages allocated = %d\n",
+			      (atoi(nr_hugepages)));
+	ret = 0;
 
  close_fd:
 	close(fd);
-	printf("Not OK. Compaction test failed.");
-	return -1;
+	return ret;
 }
 
 
 int main(int argc, char **argv)
 {
 	struct rlimit lim;
-	struct map_list *list, *entry;
+	struct map_list *list = NULL, *entry;
 	size_t page_size, i;
 	void *map = NULL;
 	unsigned long mem_free = 0;
 	unsigned long hugepage_size = 0;
 	long mem_fragmentable_MB = 0;
 
-	if (prereq() != 0) {
-		printf("Either the sysctl compact_unevictable_allowed is not\n"
-		       "set to 1 or couldn't read the proc file.\n"
-		       "Skipping the test\n");
-		return KSFT_SKIP;
-	}
+	ksft_print_header();
+
+	if (prereq() != 0)
+		return ksft_exit_pass();
+
+	ksft_set_plan(1);
 
 	lim.rlim_cur = RLIM_INFINITY;
 	lim.rlim_max = RLIM_INFINITY;
-	if (setrlimit(RLIMIT_MEMLOCK, &lim)) {
-		perror("Failed to set rlimit:\n");
-		return -1;
-	}
+	if (setrlimit(RLIMIT_MEMLOCK, &lim))
+		ksft_exit_fail_msg("Failed to set rlimit: %s\n", strerror(errno));
 
 	page_size = getpagesize();
 
-	list = NULL;
-
-	if (read_memory_info(&mem_free, &hugepage_size) != 0) {
-		printf("ERROR: Cannot read meminfo\n");
-		return -1;
-	}
+	if (read_memory_info(&mem_free, &hugepage_size) != 0)
+		ksft_exit_fail_msg("Failed to get meminfo\n");
 
 	mem_fragmentable_MB = mem_free * 0.8 / 1024;
 
@@ -225,7 +230,7 @@
 	}
 
 	if (check_compaction(mem_free, hugepage_size) == 0)
-		return 0;
+		return ksft_exit_pass();
 
-	return -1;
+	return ksft_exit_fail();
 }
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/hmm-tests.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/hmm-tests.c
@@ -1251,6 +1251,48 @@
 /*
  * Test memory snapshot without faulting in pages accessed by the device.
  */
+TEST_F(hmm, mixedmap)
+{
+	struct hmm_buffer *buffer;
+	unsigned long npages;
+	unsigned long size;
+	unsigned char *m;
+	int ret;
+
+	npages = 1;
+	size = npages << self->page_shift;
+
+	buffer = malloc(sizeof(*buffer));
+	ASSERT_NE(buffer, NULL);
+
+	buffer->fd = -1;
+	buffer->size = size;
+	buffer->mirror = malloc(npages);
+	ASSERT_NE(buffer->mirror, NULL);
+
+
+	/* Reserve a range of addresses. */
+	buffer->ptr = mmap(NULL, size,
+			   PROT_READ | PROT_WRITE,
+			   MAP_PRIVATE,
+			   self->fd, 0);
+	ASSERT_NE(buffer->ptr, MAP_FAILED);
+
+	/* Simulate a device snapshotting CPU pagetables. */
+	ret = hmm_dmirror_cmd(self->fd, HMM_DMIRROR_SNAPSHOT, buffer, npages);
+	ASSERT_EQ(ret, 0);
+	ASSERT_EQ(buffer->cpages, npages);
+
+	/* Check what the device saw. */
+	m = buffer->mirror;
+	ASSERT_EQ(m[0], HMM_DMIRROR_PROT_READ);
+
+	hmm_buffer_free(buffer);
+}
+
+/*
+ * Test memory snapshot without faulting in pages accessed by the device.
+ */
 TEST_F(hmm2, snapshot)
 {
 	struct hmm_buffer *buffer;
@@ -1440,7 +1482,7 @@
 
 	buffer->fd = -1;
 	buffer->size = size;
-	buffer->mirror = malloc(npages);
+	buffer->mirror = malloc(size);
 	ASSERT_NE(buffer->mirror, NULL);
 
 	/* Reserve a range of addresses. */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/hugetlb_reparenting_test.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/hugetlb_reparenting_test.sh
@@ -18,19 +18,24 @@
   usage_file=current
 fi
 
-CGROUP_ROOT='/dev/cgroup/memory'
-MNT='/mnt/huge/'
 
-if [[ ! -e $CGROUP_ROOT ]]; then
-  mkdir -p $CGROUP_ROOT
-  if [[ $cgroup2 ]]; then
+if [[ $cgroup2 ]]; then
+  CGROUP_ROOT=$(mount -t cgroup2 | head -1 | awk '{print $3}')
+  if [[ -z "$CGROUP_ROOT" ]]; then
+    CGROUP_ROOT=/dev/cgroup/memory
     mount -t cgroup2 none $CGROUP_ROOT
-    sleep 1
-    echo "+hugetlb +memory" >$CGROUP_ROOT/cgroup.subtree_control
-  else
+    do_umount=1
+  fi
+  echo "+hugetlb +memory" >$CGROUP_ROOT/cgroup.subtree_control
+else
+  CGROUP_ROOT=$(mount -t cgroup | grep ",hugetlb" | awk '{print $3}')
+  if [[ -z "$CGROUP_ROOT" ]]; then
+    CGROUP_ROOT=/dev/cgroup/memory
     mount -t cgroup memory,hugetlb $CGROUP_ROOT
+    do_umount=1
   fi
 fi
+MNT='/mnt/huge/'
 
 function get_machine_hugepage_size() {
   hpz=$(grep -i hugepagesize /proc/meminfo)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/map_fixed_noreplace.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/map_fixed_noreplace.c
@@ -17,9 +17,6 @@
 #define MAP_FIXED_NOREPLACE 0x100000
 #endif
 
-#define BASE_ADDRESS	(256ul * 1024 * 1024)
-
-
 static void dump_maps(void)
 {
 	char cmd[32];
@@ -28,18 +25,46 @@
 	system(cmd);
 }
 
+static unsigned long find_base_addr(unsigned long size)
+{
+	void *addr;
+	unsigned long flags;
+
+	flags = MAP_PRIVATE | MAP_ANONYMOUS;
+	addr = mmap(NULL, size, PROT_NONE, flags, -1, 0);
+	if (addr == MAP_FAILED) {
+		printf("Error: couldn't map the space we need for the test\n");
+		return 0;
+	}
+
+	if (munmap(addr, size) != 0) {
+		printf("Error: couldn't map the space we need for the test\n");
+		return 0;
+	}
+	return (unsigned long)addr;
+}
+
 int main(void)
 {
+	unsigned long base_addr;
 	unsigned long flags, addr, size, page_size;
 	char *p;
 
 	page_size = sysconf(_SC_PAGE_SIZE);
 
+	//let's find a base addr that is free before we start the tests
+	size = 5 * page_size;
+	base_addr = find_base_addr(size);
+	if (!base_addr) {
+		printf("Error: couldn't map the space we need for the test\n");
+		return 1;
+	}
+
 	flags = MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED_NOREPLACE;
 
 	// Check we can map all the areas we need below
 	errno = 0;
-	addr = BASE_ADDRESS;
+	addr = base_addr;
 	size = 5 * page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 
@@ -60,7 +85,7 @@
 	printf("unmap() successful\n");
 
 	errno = 0;
-	addr = BASE_ADDRESS + page_size;
+	addr = base_addr + page_size;
 	size = 3 * page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -80,7 +105,7 @@
 	 *     +4 |  free  | new
 	 */
 	errno = 0;
-	addr = BASE_ADDRESS;
+	addr = base_addr;
 	size = 5 * page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -101,7 +126,7 @@
 	 *     +4 |  free  |
 	 */
 	errno = 0;
-	addr = BASE_ADDRESS + (2 * page_size);
+	addr = base_addr + (2 * page_size);
 	size = page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -121,7 +146,7 @@
 	 *     +4 |  free  | new
 	 */
 	errno = 0;
-	addr = BASE_ADDRESS + (3 * page_size);
+	addr = base_addr + (3 * page_size);
 	size = 2 * page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -141,7 +166,7 @@
 	 *     +4 |  free  |
 	 */
 	errno = 0;
-	addr = BASE_ADDRESS;
+	addr = base_addr;
 	size = 2 * page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -161,7 +186,7 @@
 	 *     +4 |  free  |
 	 */
 	errno = 0;
-	addr = BASE_ADDRESS;
+	addr = base_addr;
 	size = page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -181,7 +206,7 @@
 	 *     +4 |  free  |  new
 	 */
 	errno = 0;
-	addr = BASE_ADDRESS + (4 * page_size);
+	addr = base_addr + (4 * page_size);
 	size = page_size;
 	p = mmap((void *)addr, size, PROT_NONE, flags, -1, 0);
 	printf("mmap() @ 0x%lx-0x%lx p=%p result=%m\n", addr, addr + size, p);
@@ -192,7 +217,7 @@
 		return 1;
 	}
 
-	addr = BASE_ADDRESS;
+	addr = base_addr;
 	size = 5 * page_size;
 	if (munmap((void *)addr, size) != 0) {
 		dump_maps();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/memfd_secret.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/memfd_secret.c
@@ -62,6 +62,9 @@
 	char *mem;
 
 	len = mlock_limit_cur;
+	if (len % page_size != 0)
+		len = (len/page_size) * page_size;
+
 	mem = mmap(NULL, len, prot, mode, fd, 0);
 	if (mem == MAP_FAILED) {
 		fail("unable to mmap secret memory\n");
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/mremap_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/mremap_test.c
@@ -6,9 +6,11 @@
 
 #include <errno.h>
 #include <stdlib.h>
+#include <stdio.h>
 #include <string.h>
 #include <sys/mman.h>
 #include <time.h>
+#include <stdbool.h>
 
 #include "../kselftest.h"
 
@@ -20,7 +22,6 @@
 #define VALIDATION_DEFAULT_THRESHOLD 4	/* 4MB */
 #define VALIDATION_NO_THRESHOLD 0	/* Verify the entire region */
 
-#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
 #define MIN(X, Y) ((X) < (Y) ? (X) : (Y))
 
 struct config {
@@ -65,6 +66,59 @@
 }
 
 /*
+ * Returns false if the requested remap region overlaps with an
+ * existing mapping (e.g text, stack) else returns true.
+ */
+static bool is_remap_region_valid(void *addr, unsigned long long size)
+{
+	void *remap_addr = NULL;
+	bool ret = true;
+
+	/* Use MAP_FIXED_NOREPLACE flag to ensure region is not mapped */
+	remap_addr = mmap(addr, size, PROT_READ | PROT_WRITE,
+					 MAP_FIXED_NOREPLACE | MAP_ANONYMOUS | MAP_SHARED,
+					 -1, 0);
+
+	if (remap_addr == MAP_FAILED) {
+		if (errno == EEXIST)
+			ret = false;
+	} else {
+		munmap(remap_addr, size);
+	}
+
+	return ret;
+}
+
+/* Returns mmap_min_addr sysctl tunable from procfs */
+static unsigned long long get_mmap_min_addr(void)
+{
+	FILE *fp;
+	int n_matched;
+	static unsigned long long addr;
+
+	if (addr)
+		return addr;
+
+	fp = fopen("/proc/sys/vm/mmap_min_addr", "r");
+	if (fp == NULL) {
+		ksft_print_msg("Failed to open /proc/sys/vm/mmap_min_addr: %s\n",
+			strerror(errno));
+		exit(KSFT_SKIP);
+	}
+
+	n_matched = fscanf(fp, "%llu", &addr);
+	if (n_matched != 1) {
+		ksft_print_msg("Failed to read /proc/sys/vm/mmap_min_addr: %s\n",
+			strerror(errno));
+		fclose(fp);
+		exit(KSFT_SKIP);
+	}
+
+	fclose(fp);
+	return addr;
+}
+
+/*
  * Returns the start address of the mapping on success, else returns
  * NULL on failure.
  */
@@ -72,11 +126,18 @@
 {
 	unsigned long long addr = 0ULL;
 	void *src_addr = NULL;
+	unsigned long long mmap_min_addr;
+
+	mmap_min_addr = get_mmap_min_addr();
+
 retry:
 	addr += c.src_alignment;
+	if (addr < mmap_min_addr)
+		goto retry;
+
 	src_addr = mmap((void *) addr, c.region_size, PROT_READ | PROT_WRITE,
-			MAP_FIXED_NOREPLACE | MAP_ANONYMOUS | MAP_SHARED,
-			-1, 0);
+					MAP_FIXED_NOREPLACE | MAP_ANONYMOUS | MAP_SHARED,
+					-1, 0);
 	if (src_addr == MAP_FAILED) {
 		if (errno == EPERM || errno == EEXIST)
 			goto retry;
@@ -91,8 +152,10 @@
 	 * alignment in the tests.
 	 */
 	if (((unsigned long long) src_addr & (c.src_alignment - 1)) ||
-			!((unsigned long long) src_addr & c.src_alignment))
+			!((unsigned long long) src_addr & c.src_alignment)) {
+		munmap(src_addr, c.region_size);
 		goto retry;
+	}
 
 	if (!src_addr)
 		goto error;
@@ -141,9 +204,20 @@
 	if (!((unsigned long long) addr & c.dest_alignment))
 		addr = (void *) ((unsigned long long) addr | c.dest_alignment);
 
+	/* Don't destroy existing mappings unless expected to overlap */
+	while (!is_remap_region_valid(addr, c.region_size) && !c.overlapping) {
+		/* Check for unsigned overflow */
+		if (addr + c.dest_alignment < addr) {
+			ksft_print_msg("Couldn't find a valid region to remap to\n");
+			ret = -1;
+			goto out;
+		}
+		addr += c.dest_alignment;
+	}
+
 	clock_gettime(CLOCK_MONOTONIC, &t_start);
 	dest_addr = mremap(src_addr, c.region_size, c.region_size,
-			MREMAP_MAYMOVE|MREMAP_FIXED, (char *) addr);
+					  MREMAP_MAYMOVE|MREMAP_FIXED, (char *) addr);
 	clock_gettime(CLOCK_MONOTONIC, &t_end);
 
 	if (dest_addr == MAP_FAILED) {
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/pkey-helpers.h
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/pkey-helpers.h
@@ -13,6 +13,8 @@
 #include <ucontext.h>
 #include <sys/mman.h>
 
+#include "../kselftest.h"
+
 /* Define some kernel-like types */
 #define  u8 __u8
 #define u16 __u16
@@ -175,7 +177,6 @@
 	dprintf4("pkey_reg now: %016llx\n", read_pkey_reg());
 }
 
-#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
 #define ALIGN_UP(x, align_to)	(((x) + ((align_to)-1)) & ~((align_to)-1))
 #define ALIGN_DOWN(x, align_to) ((x) & ~((align_to)-1))
 #define ALIGN_PTR_UP(p, ptr_align_to)	\
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/userfaultfd.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/userfaultfd.c
@@ -46,6 +46,7 @@
 #include <signal.h>
 #include <poll.h>
 #include <string.h>
+#include <linux/mman.h>
 #include <sys/mman.h>
 #include <sys/syscall.h>
 #include <sys/ioctl.h>
@@ -86,7 +87,7 @@
 
 static bool map_shared;
 static int shm_fd;
-static int huge_fd;
+static int huge_fd = -1;	/* only used for hugetlb_shared test */
 static char *huge_fd_off0;
 static unsigned long long *count_verify;
 static int uffd = -1;
@@ -222,6 +223,9 @@
 
 static void hugetlb_release_pages(char *rel_area)
 {
+	if (huge_fd == -1)
+		return;
+
 	if (fallocate(huge_fd, FALLOC_FL_PUNCH_HOLE | FALLOC_FL_KEEP_SIZE,
 		      rel_area == huge_fd_off0 ? 0 : nr_pages * page_size,
 		      nr_pages * page_size))
@@ -234,16 +238,17 @@
 	char **alloc_area_alias;
 
 	*alloc_area = mmap(NULL, nr_pages * page_size, PROT_READ | PROT_WRITE,
-			   (map_shared ? MAP_SHARED : MAP_PRIVATE) |
-			   MAP_HUGETLB,
-			   huge_fd, *alloc_area == area_src ? 0 :
-			   nr_pages * page_size);
+			   map_shared ? MAP_SHARED :
+			   MAP_PRIVATE | MAP_HUGETLB |
+			   (*alloc_area == area_src ? 0 : MAP_NORESERVE),
+			   huge_fd,
+			   *alloc_area == area_src ? 0 : nr_pages * page_size);
 	if (*alloc_area == MAP_FAILED)
 		err("mmap of hugetlbfs file failed");
 
 	if (map_shared) {
 		area_alias = mmap(NULL, nr_pages * page_size, PROT_READ | PROT_WRITE,
-				  MAP_SHARED | MAP_HUGETLB,
+				  MAP_SHARED,
 				  huge_fd, *alloc_area == area_src ? 0 :
 				  nr_pages * page_size);
 		if (area_alias == MAP_FAILED)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/va_128TBswitch.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/va_128TBswitch.c
@@ -9,7 +9,7 @@
 #include <sys/mman.h>
 #include <string.h>
 
-#define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]))
+#include "../kselftest.h"
 
 #ifdef __powerpc64__
 #define PAGE_SIZE	(64 << 10)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/write_hugetlb_memory.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/write_hugetlb_memory.sh
@@ -1,4 +1,4 @@
-#!/bin/sh
+#!/bin/bash
 # SPDX-License-Identifier: GPL-2.0
 
 set -e
@@ -14,7 +14,7 @@
 reserve=$9
 
 echo "Putting task in cgroup '$cgroup'"
-echo $$ > /dev/cgroup/memory/"$cgroup"/cgroup.procs
+echo $$ > ${cgroup_path:-/dev/cgroup/memory}/"$cgroup"/cgroup.procs
 
 echo "Method is $method"
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/vm/write_to_hugetlbfs.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/vm/write_to_hugetlbfs.c
@@ -28,7 +28,7 @@
 
 /* Global variables. */
 static const char *self;
-static char *shmaddr;
+static int *shmaddr;
 static int shmid;
 
 /*
@@ -47,15 +47,17 @@
 {
 	printf("Received %d.\n", signo);
 	if (signo == SIGINT) {
-		printf("Deleting the memory\n");
-		if (shmdt((const void *)shmaddr) != 0) {
-			perror("Detach failure");
+		if (shmaddr) {
+			printf("Deleting the memory\n");
+			if (shmdt((const void *)shmaddr) != 0) {
+				perror("Detach failure");
+				shmctl(shmid, IPC_RMID, NULL);
+				exit(4);
+			}
+
 			shmctl(shmid, IPC_RMID, NULL);
-			exit(4);
+			printf("Done deleting the memory\n");
 		}
-
-		shmctl(shmid, IPC_RMID, NULL);
-		printf("Done deleting the memory\n");
 	}
 	exit(2);
 }
@@ -211,7 +213,8 @@
 			shmctl(shmid, IPC_RMID, NULL);
 			exit(2);
 		}
-		printf("shmaddr: %p\n", ptr);
+		shmaddr = ptr;
+		printf("shmaddr: %p\n", shmaddr);
 
 		break;
 	default:
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/watchdog/watchdog-test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/watchdog/watchdog-test.c
@@ -242,7 +242,13 @@
 
 	printf("Watchdog Ticking Away!\n");
 
+	/*
+	 * Register the signals
+	 */
 	signal(SIGINT, term);
+	signal(SIGTERM, term);
+	signal(SIGKILL, term);
+	signal(SIGQUIT, term);
 
 	while (1) {
 		keep_alive();
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/wireguard/netns.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/wireguard/netns.sh
@@ -276,7 +276,11 @@
 n1 wg set wg0 peer "$pub2" endpoint 192.168.241.2:7
 ip2 link del wg0
 ip2 link del wg1
-! n0 ping -W 1 -c 10 -f 192.168.241.2 || false # Should not crash kernel
+read _ _ tx_bytes_before < <(n0 wg show wg1 transfer)
+! n0 ping -W 1 -c 10 -f 192.168.241.2 || false
+sleep 1
+read _ _ tx_bytes_after < <(n0 wg show wg1 transfer)
+(( tx_bytes_after - tx_bytes_before < 70000 ))
 
 ip0 link del wg1
 ip1 link del wg0
@@ -316,6 +320,7 @@
 waitiface $netns2 veths
 
 n0 bash -c 'printf 1 > /proc/sys/net/ipv4/ip_forward'
+[[ -e /proc/sys/net/netfilter/nf_conntrack_udp_timeout ]] || modprobe nf_conntrack
 n0 bash -c 'printf 2 > /proc/sys/net/netfilter/nf_conntrack_udp_timeout'
 n0 bash -c 'printf 2 > /proc/sys/net/netfilter/nf_conntrack_udp_timeout_stream'
 n0 iptables -t nat -A POSTROUTING -s 192.168.1.0/24 -d 10.0.0.0/24 -j SNAT --to 10.0.0.1
@@ -498,10 +503,32 @@
 n1 ping -W 1 -c 1 192.168.241.2
 [[ $(n2 wg show wg0 endpoints) == "$pub1	10.0.0.3:1" ]]
 
-ip1 link del veth1
-ip1 link del veth3
-ip1 link del wg0
-ip2 link del wg0
+ip1 link del dev veth3
+ip1 link del dev wg0
+ip2 link del dev wg0
+
+# Make sure persistent keep alives are sent when an adapter comes up
+ip1 link add dev wg0 type wireguard
+n1 wg set wg0 private-key <(echo "$key1") peer "$pub2" endpoint 10.0.0.1:1 persistent-keepalive 1
+read _ _ tx_bytes < <(n1 wg show wg0 transfer)
+[[ $tx_bytes -eq 0 ]]
+ip1 link set dev wg0 up
+read _ _ tx_bytes < <(n1 wg show wg0 transfer)
+[[ $tx_bytes -gt 0 ]]
+ip1 link del dev wg0
+# This should also happen even if the private key is set later
+ip1 link add dev wg0 type wireguard
+n1 wg set wg0 peer "$pub2" endpoint 10.0.0.1:1 persistent-keepalive 1
+read _ _ tx_bytes < <(n1 wg show wg0 transfer)
+[[ $tx_bytes -eq 0 ]]
+ip1 link set dev wg0 up
+read _ _ tx_bytes < <(n1 wg show wg0 transfer)
+[[ $tx_bytes -eq 0 ]]
+n1 wg set wg0 private-key <(echo "$key1")
+read _ _ tx_bytes < <(n1 wg show wg0 transfer)
+[[ $tx_bytes -gt 0 ]]
+ip1 link del dev veth1
+ip1 link del dev wg0
 
 # We test that Netlink/IPC is working properly by doing things that usually cause split responses
 ip0 link add dev wg0 type wireguard
@@ -609,6 +636,28 @@
 kill $ncat_pid
 ip0 link del wg0
 
+# Ensure that dst_cache references don't outlive netns lifetime
+ip1 link add dev wg0 type wireguard
+ip2 link add dev wg0 type wireguard
+configure_peers
+ip1 link add veth1 type veth peer name veth2
+ip1 link set veth2 netns $netns2
+ip1 addr add fd00:aa::1/64 dev veth1
+ip2 addr add fd00:aa::2/64 dev veth2
+ip1 link set veth1 up
+ip2 link set veth2 up
+waitiface $netns1 veth1
+waitiface $netns2 veth2
+ip1 -6 route add default dev veth1 via fd00:aa::2
+ip2 -6 route add default dev veth2 via fd00:aa::1
+n1 wg set wg0 peer "$pub2" endpoint [fd00:aa::2]:2
+n2 wg set wg0 peer "$pub1" endpoint [fd00:aa::1]:1
+n1 ping6 -c 1 fd00::2
+pp ip netns delete $netns1
+pp ip netns delete $netns2
+pp ip netns add $netns1
+pp ip netns add $netns2
+
 # Ensure there aren't circular reference loops
 ip1 link add wg1 type wireguard
 ip2 link add wg2 type wireguard
@@ -627,7 +676,7 @@
 done < /dev/kmsg
 alldeleted=1
 for object in "${!objects[@]}"; do
-	if [[ ${objects["$object"]} != *createddestroyed ]]; then
+	if [[ ${objects["$object"]} != *createddestroyed && ${objects["$object"]} != *createdcreateddestroyeddestroyed ]]; then
 		echo "Error: $object: merely ${objects["$object"]}" >&3
 		alldeleted=0
 	fi
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/wireguard/qemu/debug.config
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/wireguard/qemu/debug.config
@@ -47,7 +47,7 @@
 CONFIG_TRACE_IRQFLAGS=y
 CONFIG_DEBUG_BUGVERBOSE=y
 CONFIG_DEBUG_LIST=y
-CONFIG_DEBUG_PI_LIST=y
+CONFIG_DEBUG_PLIST=y
 CONFIG_PROVE_RCU=y
 CONFIG_SPARSE_RCU_POINTER=y
 CONFIG_RCU_CPU_STALL_TIMEOUT=21
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/wireguard/qemu/kernel.config
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/wireguard/qemu/kernel.config
@@ -66,6 +66,7 @@
 CONFIG_SYSFS=y
 CONFIG_TMPFS=y
 CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_LOG_BUF_SHIFT=18
 CONFIG_PRINTK_TIME=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_LEGACY_VSYSCALL_NONE=y
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/x86/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/x86/Makefile
@@ -6,9 +6,9 @@
 .PHONY: all all_32 all_64 warn_32bit_failure clean
 
 UNAME_M := $(shell uname -m)
-CAN_BUILD_I386 := $(shell ./check_cc.sh $(CC) trivial_32bit_program.c -m32)
-CAN_BUILD_X86_64 := $(shell ./check_cc.sh $(CC) trivial_64bit_program.c)
-CAN_BUILD_WITH_NOPIE := $(shell ./check_cc.sh $(CC) trivial_program.c -no-pie)
+CAN_BUILD_I386 := $(shell ./check_cc.sh "$(CC)" trivial_32bit_program.c -m32)
+CAN_BUILD_X86_64 := $(shell ./check_cc.sh "$(CC)" trivial_64bit_program.c)
+CAN_BUILD_WITH_NOPIE := $(shell ./check_cc.sh "$(CC)" trivial_program.c -no-pie)
 
 TARGETS_C_BOTHBITS := single_step_syscall sysret_ss_attrs syscall_nt test_mremap_vdso \
 			check_initial_reg_state sigreturn iopl ioperm \
@@ -18,7 +18,7 @@
 			test_FCMOV test_FCOMI test_FISTTP \
 			vdso_restorer
 TARGETS_C_64BIT_ONLY := fsgsbase sysret_rip syscall_numbering \
-			corrupt_xstate_header
+			corrupt_xstate_header amx
 # Some selftests require 32bit support enabled also on 64bit systems
 TARGETS_C_32BIT_NEEDED := ldt_gdt ptrace_syscall
 
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/x86/amx.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/x86/amx.c
@@ -0,0 +1,863 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#define _GNU_SOURCE
+#include <err.h>
+#include <errno.h>
+#include <pthread.h>
+#include <setjmp.h>
+#include <stdio.h>
+#include <string.h>
+#include <stdbool.h>
+#include <unistd.h>
+#include <x86intrin.h>
+
+#include <sys/auxv.h>
+#include <sys/mman.h>
+#include <sys/shm.h>
+#include <sys/syscall.h>
+#include <sys/wait.h>
+
+#ifndef __x86_64__
+# error This test is 64-bit only
+#endif
+
+#define XSAVE_HDR_OFFSET	512
+#define XSAVE_HDR_SIZE		64
+
+struct xsave_buffer {
+	union {
+		struct {
+			char legacy[XSAVE_HDR_OFFSET];
+			char header[XSAVE_HDR_SIZE];
+			char extended[0];
+		};
+		char bytes[0];
+	};
+};
+
+static inline uint64_t xgetbv(uint32_t index)
+{
+	uint32_t eax, edx;
+
+	asm volatile("xgetbv;"
+		     : "=a" (eax), "=d" (edx)
+		     : "c" (index));
+	return eax + ((uint64_t)edx << 32);
+}
+
+static inline void cpuid(uint32_t *eax, uint32_t *ebx, uint32_t *ecx, uint32_t *edx)
+{
+	asm volatile("cpuid;"
+		     : "=a" (*eax), "=b" (*ebx), "=c" (*ecx), "=d" (*edx)
+		     : "0" (*eax), "2" (*ecx));
+}
+
+static inline void xsave(struct xsave_buffer *xbuf, uint64_t rfbm)
+{
+	uint32_t rfbm_lo = rfbm;
+	uint32_t rfbm_hi = rfbm >> 32;
+
+	asm volatile("xsave (%%rdi)"
+		     : : "D" (xbuf), "a" (rfbm_lo), "d" (rfbm_hi)
+		     : "memory");
+}
+
+static inline void xrstor(struct xsave_buffer *xbuf, uint64_t rfbm)
+{
+	uint32_t rfbm_lo = rfbm;
+	uint32_t rfbm_hi = rfbm >> 32;
+
+	asm volatile("xrstor (%%rdi)"
+		     : : "D" (xbuf), "a" (rfbm_lo), "d" (rfbm_hi));
+}
+
+/* err() exits and will not return */
+#define fatal_error(msg, ...)	err(1, "[FAIL]\t" msg, ##__VA_ARGS__)
+
+static void sethandler(int sig, void (*handler)(int, siginfo_t *, void *),
+		       int flags)
+{
+	struct sigaction sa;
+
+	memset(&sa, 0, sizeof(sa));
+	sa.sa_sigaction = handler;
+	sa.sa_flags = SA_SIGINFO | flags;
+	sigemptyset(&sa.sa_mask);
+	if (sigaction(sig, &sa, 0))
+		fatal_error("sigaction");
+}
+
+static void clearhandler(int sig)
+{
+	struct sigaction sa;
+
+	memset(&sa, 0, sizeof(sa));
+	sa.sa_handler = SIG_DFL;
+	sigemptyset(&sa.sa_mask);
+	if (sigaction(sig, &sa, 0))
+		fatal_error("sigaction");
+}
+
+#define XFEATURE_XTILECFG	17
+#define XFEATURE_XTILEDATA	18
+#define XFEATURE_MASK_XTILECFG	(1 << XFEATURE_XTILECFG)
+#define XFEATURE_MASK_XTILEDATA	(1 << XFEATURE_XTILEDATA)
+#define XFEATURE_MASK_XTILE	(XFEATURE_MASK_XTILECFG | XFEATURE_MASK_XTILEDATA)
+
+#define CPUID_LEAF1_ECX_XSAVE_MASK	(1 << 26)
+#define CPUID_LEAF1_ECX_OSXSAVE_MASK	(1 << 27)
+static inline void check_cpuid_xsave(void)
+{
+	uint32_t eax, ebx, ecx, edx;
+
+	/*
+	 * CPUID.1:ECX.XSAVE[bit 26] enumerates general
+	 * support for the XSAVE feature set, including
+	 * XGETBV.
+	 */
+	eax = 1;
+	ecx = 0;
+	cpuid(&eax, &ebx, &ecx, &edx);
+	if (!(ecx & CPUID_LEAF1_ECX_XSAVE_MASK))
+		fatal_error("cpuid: no CPU xsave support");
+	if (!(ecx & CPUID_LEAF1_ECX_OSXSAVE_MASK))
+		fatal_error("cpuid: no OS xsave support");
+}
+
+static uint32_t xbuf_size;
+
+static struct {
+	uint32_t xbuf_offset;
+	uint32_t size;
+} xtiledata;
+
+#define CPUID_LEAF_XSTATE		0xd
+#define CPUID_SUBLEAF_XSTATE_USER	0x0
+#define TILE_CPUID			0x1d
+#define TILE_PALETTE_ID			0x1
+
+static void check_cpuid_xtiledata(void)
+{
+	uint32_t eax, ebx, ecx, edx;
+
+	eax = CPUID_LEAF_XSTATE;
+	ecx = CPUID_SUBLEAF_XSTATE_USER;
+	cpuid(&eax, &ebx, &ecx, &edx);
+
+	/*
+	 * EBX enumerates the size (in bytes) required by the XSAVE
+	 * instruction for an XSAVE area containing all the user state
+	 * components corresponding to bits currently set in XCR0.
+	 *
+	 * Stash that off so it can be used to allocate buffers later.
+	 */
+	xbuf_size = ebx;
+
+	eax = CPUID_LEAF_XSTATE;
+	ecx = XFEATURE_XTILEDATA;
+
+	cpuid(&eax, &ebx, &ecx, &edx);
+	/*
+	 * eax: XTILEDATA state component size
+	 * ebx: XTILEDATA state component offset in user buffer
+	 */
+	if (!eax || !ebx)
+		fatal_error("xstate cpuid: invalid tile data size/offset: %d/%d",
+				eax, ebx);
+
+	xtiledata.size	      = eax;
+	xtiledata.xbuf_offset = ebx;
+}
+
+/* The helpers for managing XSAVE buffer and tile states: */
+
+struct xsave_buffer *alloc_xbuf(void)
+{
+	struct xsave_buffer *xbuf;
+
+	/* XSAVE buffer should be 64B-aligned. */
+	xbuf = aligned_alloc(64, xbuf_size);
+	if (!xbuf)
+		fatal_error("aligned_alloc()");
+	return xbuf;
+}
+
+static inline void clear_xstate_header(struct xsave_buffer *buffer)
+{
+	memset(&buffer->header, 0, sizeof(buffer->header));
+}
+
+static inline uint64_t get_xstatebv(struct xsave_buffer *buffer)
+{
+	/* XSTATE_BV is at the beginning of the header: */
+	return *(uint64_t *)&buffer->header;
+}
+
+static inline void set_xstatebv(struct xsave_buffer *buffer, uint64_t bv)
+{
+	/* XSTATE_BV is at the beginning of the header: */
+	*(uint64_t *)(&buffer->header) = bv;
+}
+
+static void set_rand_tiledata(struct xsave_buffer *xbuf)
+{
+	int *ptr = (int *)&xbuf->bytes[xtiledata.xbuf_offset];
+	int data;
+	int i;
+
+	/*
+	 * Ensure that 'data' is never 0.  This ensures that
+	 * the registers are never in their initial configuration
+	 * and thus never tracked as being in the init state.
+	 */
+	data = rand() | 1;
+
+	for (i = 0; i < xtiledata.size / sizeof(int); i++, ptr++)
+		*ptr = data;
+}
+
+struct xsave_buffer *stashed_xsave;
+
+static void init_stashed_xsave(void)
+{
+	stashed_xsave = alloc_xbuf();
+	if (!stashed_xsave)
+		fatal_error("failed to allocate stashed_xsave\n");
+	clear_xstate_header(stashed_xsave);
+}
+
+static void free_stashed_xsave(void)
+{
+	free(stashed_xsave);
+}
+
+/* See 'struct _fpx_sw_bytes' at sigcontext.h */
+#define SW_BYTES_OFFSET		464
+/* N.B. The struct's field name varies so read from the offset. */
+#define SW_BYTES_BV_OFFSET	(SW_BYTES_OFFSET + 8)
+
+static inline struct _fpx_sw_bytes *get_fpx_sw_bytes(void *buffer)
+{
+	return (struct _fpx_sw_bytes *)(buffer + SW_BYTES_OFFSET);
+}
+
+static inline uint64_t get_fpx_sw_bytes_features(void *buffer)
+{
+	return *(uint64_t *)(buffer + SW_BYTES_BV_OFFSET);
+}
+
+/* Work around printf() being unsafe in signals: */
+#define SIGNAL_BUF_LEN 1000
+char signal_message_buffer[SIGNAL_BUF_LEN];
+void sig_print(char *msg)
+{
+	int left = SIGNAL_BUF_LEN - strlen(signal_message_buffer) - 1;
+
+	strncat(signal_message_buffer, msg, left);
+}
+
+static volatile bool noperm_signaled;
+static int noperm_errs;
+/*
+ * Signal handler for when AMX is used but
+ * permission has not been obtained.
+ */
+static void handle_noperm(int sig, siginfo_t *si, void *ctx_void)
+{
+	ucontext_t *ctx = (ucontext_t *)ctx_void;
+	void *xbuf = ctx->uc_mcontext.fpregs;
+	struct _fpx_sw_bytes *sw_bytes;
+	uint64_t features;
+
+	/* Reset the signal message buffer: */
+	signal_message_buffer[0] = '\0';
+	sig_print("\tAt SIGILL handler,\n");
+
+	if (si->si_code != ILL_ILLOPC) {
+		noperm_errs++;
+		sig_print("[FAIL]\tInvalid signal code.\n");
+	} else {
+		sig_print("[OK]\tValid signal code (ILL_ILLOPC).\n");
+	}
+
+	sw_bytes = get_fpx_sw_bytes(xbuf);
+	/*
+	 * Without permission, the signal XSAVE buffer should not
+	 * have room for AMX register state (aka. xtiledata).
+	 * Check that the size does not overlap with where xtiledata
+	 * will reside.
+	 *
+	 * This also implies that no state components *PAST*
+	 * XTILEDATA (features >=19) can be present in the buffer.
+	 */
+	if (sw_bytes->xstate_size <= xtiledata.xbuf_offset) {
+		sig_print("[OK]\tValid xstate size\n");
+	} else {
+		noperm_errs++;
+		sig_print("[FAIL]\tInvalid xstate size\n");
+	}
+
+	features = get_fpx_sw_bytes_features(xbuf);
+	/*
+	 * Without permission, the XTILEDATA feature
+	 * bit should not be set.
+	 */
+	if ((features & XFEATURE_MASK_XTILEDATA) == 0) {
+		sig_print("[OK]\tValid xstate mask\n");
+	} else {
+		noperm_errs++;
+		sig_print("[FAIL]\tInvalid xstate mask\n");
+	}
+
+	noperm_signaled = true;
+	ctx->uc_mcontext.gregs[REG_RIP] += 3; /* Skip the faulting XRSTOR */
+}
+
+/* Return true if XRSTOR is successful; otherwise, false. */
+static inline bool xrstor_safe(struct xsave_buffer *xbuf, uint64_t mask)
+{
+	noperm_signaled = false;
+	xrstor(xbuf, mask);
+
+	/* Print any messages produced by the signal code: */
+	printf("%s", signal_message_buffer);
+	/*
+	 * Reset the buffer to make sure any future printing
+	 * only outputs new messages:
+	 */
+	signal_message_buffer[0] = '\0';
+
+	if (noperm_errs)
+		fatal_error("saw %d errors in noperm signal handler\n", noperm_errs);
+
+	return !noperm_signaled;
+}
+
+/*
+ * Use XRSTOR to populate the XTILEDATA registers with
+ * random data.
+ *
+ * Return true if successful; otherwise, false.
+ */
+static inline bool load_rand_tiledata(struct xsave_buffer *xbuf)
+{
+	clear_xstate_header(xbuf);
+	set_xstatebv(xbuf, XFEATURE_MASK_XTILEDATA);
+	set_rand_tiledata(xbuf);
+	return xrstor_safe(xbuf, XFEATURE_MASK_XTILEDATA);
+}
+
+/* Return XTILEDATA to its initial configuration. */
+static inline void init_xtiledata(void)
+{
+	clear_xstate_header(stashed_xsave);
+	xrstor_safe(stashed_xsave, XFEATURE_MASK_XTILEDATA);
+}
+
+enum expected_result { FAIL_EXPECTED, SUCCESS_EXPECTED };
+
+/* arch_prctl() and sigaltstack() test */
+
+#define ARCH_GET_XCOMP_PERM	0x1022
+#define ARCH_REQ_XCOMP_PERM	0x1023
+
+static void req_xtiledata_perm(void)
+{
+	syscall(SYS_arch_prctl, ARCH_REQ_XCOMP_PERM, XFEATURE_XTILEDATA);
+}
+
+static void validate_req_xcomp_perm(enum expected_result exp)
+{
+	unsigned long bitmask, expected_bitmask;
+	long rc;
+
+	rc = syscall(SYS_arch_prctl, ARCH_GET_XCOMP_PERM, &bitmask);
+	if (rc) {
+		fatal_error("prctl(ARCH_GET_XCOMP_PERM) error: %ld", rc);
+	} else if (!(bitmask & XFEATURE_MASK_XTILECFG)) {
+		fatal_error("ARCH_GET_XCOMP_PERM returns XFEATURE_XTILECFG off.");
+	}
+
+	rc = syscall(SYS_arch_prctl, ARCH_REQ_XCOMP_PERM, XFEATURE_XTILEDATA);
+	if (exp == FAIL_EXPECTED) {
+		if (rc) {
+			printf("[OK]\tARCH_REQ_XCOMP_PERM saw expected failure..\n");
+			return;
+		}
+
+		fatal_error("ARCH_REQ_XCOMP_PERM saw unexpected success.\n");
+	} else if (rc) {
+		fatal_error("ARCH_REQ_XCOMP_PERM saw unexpected failure.\n");
+	}
+
+	expected_bitmask = bitmask | XFEATURE_MASK_XTILEDATA;
+
+	rc = syscall(SYS_arch_prctl, ARCH_GET_XCOMP_PERM, &bitmask);
+	if (rc) {
+		fatal_error("prctl(ARCH_GET_XCOMP_PERM) error: %ld", rc);
+	} else if (bitmask != expected_bitmask) {
+		fatal_error("ARCH_REQ_XCOMP_PERM set a wrong bitmask: %lx, expected: %lx.\n",
+			    bitmask, expected_bitmask);
+	} else {
+		printf("\tARCH_REQ_XCOMP_PERM is successful.\n");
+	}
+}
+
+static void validate_xcomp_perm(enum expected_result exp)
+{
+	bool load_success = load_rand_tiledata(stashed_xsave);
+
+	if (exp == FAIL_EXPECTED) {
+		if (load_success) {
+			noperm_errs++;
+			printf("[FAIL]\tLoad tiledata succeeded.\n");
+		} else {
+			printf("[OK]\tLoad tiledata failed.\n");
+		}
+	} else if (exp == SUCCESS_EXPECTED) {
+		if (load_success) {
+			printf("[OK]\tLoad tiledata succeeded.\n");
+		} else {
+			noperm_errs++;
+			printf("[FAIL]\tLoad tiledata failed.\n");
+		}
+	}
+}
+
+#ifndef AT_MINSIGSTKSZ
+#  define AT_MINSIGSTKSZ	51
+#endif
+
+static void *alloc_altstack(unsigned int size)
+{
+	void *altstack;
+
+	altstack = mmap(NULL, size, PROT_READ | PROT_WRITE,
+			MAP_PRIVATE | MAP_ANONYMOUS | MAP_STACK, -1, 0);
+
+	if (altstack == MAP_FAILED)
+		fatal_error("mmap() for altstack");
+
+	return altstack;
+}
+
+static void setup_altstack(void *addr, unsigned long size, enum expected_result exp)
+{
+	stack_t ss;
+	int rc;
+
+	memset(&ss, 0, sizeof(ss));
+	ss.ss_size = size;
+	ss.ss_sp = addr;
+
+	rc = sigaltstack(&ss, NULL);
+
+	if (exp == FAIL_EXPECTED) {
+		if (rc) {
+			printf("[OK]\tsigaltstack() failed.\n");
+		} else {
+			fatal_error("sigaltstack() succeeded unexpectedly.\n");
+		}
+	} else if (rc) {
+		fatal_error("sigaltstack()");
+	}
+}
+
+static void test_dynamic_sigaltstack(void)
+{
+	unsigned int small_size, enough_size;
+	unsigned long minsigstksz;
+	void *altstack;
+
+	minsigstksz = getauxval(AT_MINSIGSTKSZ);
+	printf("\tAT_MINSIGSTKSZ = %lu\n", minsigstksz);
+	/*
+	 * getauxval() itself can return 0 for failure or
+	 * success.  But, in this case, AT_MINSIGSTKSZ
+	 * will always return a >=0 value if implemented.
+	 * Just check for 0.
+	 */
+	if (minsigstksz == 0) {
+		printf("no support for AT_MINSIGSTKSZ, skipping sigaltstack tests\n");
+		return;
+	}
+
+	enough_size = minsigstksz * 2;
+
+	altstack = alloc_altstack(enough_size);
+	printf("\tAllocate memory for altstack (%u bytes).\n", enough_size);
+
+	/*
+	 * Try setup_altstack() with a size which can not fit
+	 * XTILEDATA.  ARCH_REQ_XCOMP_PERM should fail.
+	 */
+	small_size = minsigstksz - xtiledata.size;
+	printf("\tAfter sigaltstack() with small size (%u bytes).\n", small_size);
+	setup_altstack(altstack, small_size, SUCCESS_EXPECTED);
+	validate_req_xcomp_perm(FAIL_EXPECTED);
+
+	/*
+	 * Try setup_altstack() with a size derived from
+	 * AT_MINSIGSTKSZ.  It should be more than large enough
+	 * and thus ARCH_REQ_XCOMP_PERM should succeed.
+	 */
+	printf("\tAfter sigaltstack() with enough size (%u bytes).\n", enough_size);
+	setup_altstack(altstack, enough_size, SUCCESS_EXPECTED);
+	validate_req_xcomp_perm(SUCCESS_EXPECTED);
+
+	/*
+	 * Try to coerce setup_altstack() to again accept a
+	 * too-small altstack.  This ensures that big-enough
+	 * sigaltstacks can not shrink to a too-small value
+	 * once XTILEDATA permission is established.
+	 */
+	printf("\tThen, sigaltstack() with small size (%u bytes).\n", small_size);
+	setup_altstack(altstack, small_size, FAIL_EXPECTED);
+}
+
+static void test_dynamic_state(void)
+{
+	pid_t parent, child, grandchild;
+
+	parent = fork();
+	if (parent < 0) {
+		/* fork() failed */
+		fatal_error("fork");
+	} else if (parent > 0) {
+		int status;
+		/* fork() succeeded.  Now in the parent. */
+
+		wait(&status);
+		if (!WIFEXITED(status) || WEXITSTATUS(status))
+			fatal_error("arch_prctl test parent exit");
+		return;
+	}
+	/* fork() succeeded.  Now in the child . */
+
+	printf("[RUN]\tCheck ARCH_REQ_XCOMP_PERM around process fork() and sigaltack() test.\n");
+
+	printf("\tFork a child.\n");
+	child = fork();
+	if (child < 0) {
+		fatal_error("fork");
+	} else if (child > 0) {
+		int status;
+
+		wait(&status);
+		if (!WIFEXITED(status) || WEXITSTATUS(status))
+			fatal_error("arch_prctl test child exit");
+		_exit(0);
+	}
+
+	/*
+	 * The permission request should fail without an
+	 * XTILEDATA-compatible signal stack
+	 */
+	printf("\tTest XCOMP_PERM at child.\n");
+	validate_xcomp_perm(FAIL_EXPECTED);
+
+	/*
+	 * Set up an XTILEDATA-compatible signal stack and
+	 * also obtain permission to populate XTILEDATA.
+	 */
+	printf("\tTest dynamic sigaltstack at child:\n");
+	test_dynamic_sigaltstack();
+
+	/* Ensure that XTILEDATA can be populated. */
+	printf("\tTest XCOMP_PERM again at child.\n");
+	validate_xcomp_perm(SUCCESS_EXPECTED);
+
+	printf("\tFork a grandchild.\n");
+	grandchild = fork();
+	if (grandchild < 0) {
+		/* fork() failed */
+		fatal_error("fork");
+	} else if (!grandchild) {
+		/* fork() succeeded.  Now in the (grand)child. */
+		printf("\tTest XCOMP_PERM at grandchild.\n");
+
+		/*
+		 * Ensure that the grandchild inherited
+		 * permission and a compatible sigaltstack:
+		 */
+		validate_xcomp_perm(SUCCESS_EXPECTED);
+	} else {
+		int status;
+		/* fork() succeeded.  Now in the parent. */
+
+		wait(&status);
+		if (!WIFEXITED(status) || WEXITSTATUS(status))
+			fatal_error("fork test grandchild");
+	}
+
+	_exit(0);
+}
+
+/*
+ * Save current register state and compare it to @xbuf1.'
+ *
+ * Returns false if @xbuf1 matches the registers.
+ * Returns true  if @xbuf1 differs from the registers.
+ */
+static inline bool __validate_tiledata_regs(struct xsave_buffer *xbuf1)
+{
+	struct xsave_buffer *xbuf2;
+	int ret;
+
+	xbuf2 = alloc_xbuf();
+	if (!xbuf2)
+		fatal_error("failed to allocate XSAVE buffer\n");
+
+	xsave(xbuf2, XFEATURE_MASK_XTILEDATA);
+	ret = memcmp(&xbuf1->bytes[xtiledata.xbuf_offset],
+		     &xbuf2->bytes[xtiledata.xbuf_offset],
+		     xtiledata.size);
+
+	free(xbuf2);
+
+	if (ret == 0)
+		return false;
+	return true;
+}
+
+static inline void validate_tiledata_regs_same(struct xsave_buffer *xbuf)
+{
+	int ret = __validate_tiledata_regs(xbuf);
+
+	if (ret != 0)
+		fatal_error("TILEDATA registers changed");
+}
+
+static inline void validate_tiledata_regs_changed(struct xsave_buffer *xbuf)
+{
+	int ret = __validate_tiledata_regs(xbuf);
+
+	if (ret == 0)
+		fatal_error("TILEDATA registers did not change");
+}
+
+/* tiledata inheritance test */
+
+static void test_fork(void)
+{
+	pid_t child, grandchild;
+
+	child = fork();
+	if (child < 0) {
+		/* fork() failed */
+		fatal_error("fork");
+	} else if (child > 0) {
+		/* fork() succeeded.  Now in the parent. */
+		int status;
+
+		wait(&status);
+		if (!WIFEXITED(status) || WEXITSTATUS(status))
+			fatal_error("fork test child");
+		return;
+	}
+	/* fork() succeeded.  Now in the child. */
+	printf("[RUN]\tCheck tile data inheritance.\n\tBefore fork(), load tiledata\n");
+
+	load_rand_tiledata(stashed_xsave);
+
+	grandchild = fork();
+	if (grandchild < 0) {
+		/* fork() failed */
+		fatal_error("fork");
+	} else if (grandchild > 0) {
+		/* fork() succeeded.  Still in the first child. */
+		int status;
+
+		wait(&status);
+		if (!WIFEXITED(status) || WEXITSTATUS(status))
+			fatal_error("fork test grand child");
+		_exit(0);
+	}
+	/* fork() succeeded.  Now in the (grand)child. */
+
+	/*
+	 * TILEDATA registers are not preserved across fork().
+	 * Ensure that their value has changed:
+	 */
+	validate_tiledata_regs_changed(stashed_xsave);
+
+	_exit(0);
+}
+
+/* Context switching test */
+
+static struct _ctxtswtest_cfg {
+	unsigned int iterations;
+	unsigned int num_threads;
+} ctxtswtest_config;
+
+struct futex_info {
+	pthread_t thread;
+	int nr;
+	pthread_mutex_t mutex;
+	struct futex_info *next;
+};
+
+static void *check_tiledata(void *info)
+{
+	struct futex_info *finfo = (struct futex_info *)info;
+	struct xsave_buffer *xbuf;
+	int i;
+
+	xbuf = alloc_xbuf();
+	if (!xbuf)
+		fatal_error("unable to allocate XSAVE buffer");
+
+	/*
+	 * Load random data into 'xbuf' and then restore
+	 * it to the tile registers themselves.
+	 */
+	load_rand_tiledata(xbuf);
+	for (i = 0; i < ctxtswtest_config.iterations; i++) {
+		pthread_mutex_lock(&finfo->mutex);
+
+		/*
+		 * Ensure the register values have not
+		 * diverged from those recorded in 'xbuf'.
+		 */
+		validate_tiledata_regs_same(xbuf);
+
+		/* Load new, random values into xbuf and registers */
+		load_rand_tiledata(xbuf);
+
+		/*
+		 * The last thread's last unlock will be for
+		 * thread 0's mutex.  However, thread 0 will
+		 * have already exited the loop and the mutex
+		 * will already be unlocked.
+		 *
+		 * Because this is not an ERRORCHECK mutex,
+		 * that inconsistency will be silently ignored.
+		 */
+		pthread_mutex_unlock(&finfo->next->mutex);
+	}
+
+	free(xbuf);
+	/*
+	 * Return this thread's finfo, which is
+	 * a unique value for this thread.
+	 */
+	return finfo;
+}
+
+static int create_threads(int num, struct futex_info *finfo)
+{
+	int i;
+
+	for (i = 0; i < num; i++) {
+		int next_nr;
+
+		finfo[i].nr = i;
+		/*
+		 * Thread 'i' will wait on this mutex to
+		 * be unlocked.  Lock it immediately after
+		 * initialization:
+		 */
+		pthread_mutex_init(&finfo[i].mutex, NULL);
+		pthread_mutex_lock(&finfo[i].mutex);
+
+		next_nr = (i + 1) % num;
+		finfo[i].next = &finfo[next_nr];
+
+		if (pthread_create(&finfo[i].thread, NULL, check_tiledata, &finfo[i]))
+			fatal_error("pthread_create()");
+	}
+	return 0;
+}
+
+static void affinitize_cpu0(void)
+{
+	cpu_set_t cpuset;
+
+	CPU_ZERO(&cpuset);
+	CPU_SET(0, &cpuset);
+
+	if (sched_setaffinity(0, sizeof(cpuset), &cpuset) != 0)
+		fatal_error("sched_setaffinity to CPU 0");
+}
+
+static void test_context_switch(void)
+{
+	struct futex_info *finfo;
+	int i;
+
+	/* Affinitize to one CPU to force context switches */
+	affinitize_cpu0();
+
+	req_xtiledata_perm();
+
+	printf("[RUN]\tCheck tiledata context switches, %d iterations, %d threads.\n",
+	       ctxtswtest_config.iterations,
+	       ctxtswtest_config.num_threads);
+
+
+	finfo = malloc(sizeof(*finfo) * ctxtswtest_config.num_threads);
+	if (!finfo)
+		fatal_error("malloc()");
+
+	create_threads(ctxtswtest_config.num_threads, finfo);
+
+	/*
+	 * This thread wakes up thread 0
+	 * Thread 0 will wake up 1
+	 * Thread 1 will wake up 2
+	 * ...
+	 * the last thread will wake up 0
+	 *
+	 * ... this will repeat for the configured
+	 * number of iterations.
+	 */
+	pthread_mutex_unlock(&finfo[0].mutex);
+
+	/* Wait for all the threads to finish: */
+	for (i = 0; i < ctxtswtest_config.num_threads; i++) {
+		void *thread_retval;
+		int rc;
+
+		rc = pthread_join(finfo[i].thread, &thread_retval);
+
+		if (rc)
+			fatal_error("pthread_join() failed for thread %d err: %d\n",
+					i, rc);
+
+		if (thread_retval != &finfo[i])
+			fatal_error("unexpected thread retval for thread %d: %p\n",
+					i, thread_retval);
+
+	}
+
+	printf("[OK]\tNo incorrect case was found.\n");
+
+	free(finfo);
+}
+
+int main(void)
+{
+	/* Check hardware availability at first */
+	check_cpuid_xsave();
+	check_cpuid_xtiledata();
+
+	init_stashed_xsave();
+	sethandler(SIGILL, handle_noperm, 0);
+
+	test_dynamic_state();
+
+	/* Request permission for the following tests */
+	req_xtiledata_perm();
+
+	test_fork();
+
+	ctxtswtest_config.iterations = 10;
+	ctxtswtest_config.num_threads = 5;
+	test_context_switch();
+
+	clearhandler(SIGILL);
+	free_stashed_xsave();
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/x86/check_cc.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/x86/check_cc.sh
@@ -7,7 +7,7 @@
 TESTPROG="$2"
 shift 2
 
-if "$CC" -o /dev/null "$TESTPROG" -O0 "$@" 2>/dev/null; then
+if [ -n "$CC" ] && $CC -o /dev/null "$TESTPROG" -O0 "$@" 2>/dev/null; then
     echo 1
 else
     echo 0
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/x86/iopl.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/x86/iopl.c
@@ -85,48 +85,88 @@
 	printf("[OK]\toutb to 0x%02hx failed\n", port);
 }
 
-static bool try_cli(void)
+#define RET_FAULTED	0
+#define RET_FAIL	1
+#define RET_EMUL	2
+
+static int try_cli(void)
 {
+	unsigned long flags;
+
 	sethandler(SIGSEGV, sigsegv, SA_RESETHAND);
 	if (sigsetjmp(jmpbuf, 1) != 0) {
-		return false;
+		return RET_FAULTED;
 	} else {
-		asm volatile ("cli");
-		return true;
+		asm volatile("cli; pushf; pop %[flags]"
+				: [flags] "=rm" (flags));
+
+		/* X86_FLAGS_IF */
+		if (!(flags & (1 << 9)))
+			return RET_FAIL;
+		else
+			return RET_EMUL;
 	}
 	clearhandler(SIGSEGV);
 }
 
-static bool try_sti(void)
+static int try_sti(bool irqs_off)
 {
+	unsigned long flags;
+
 	sethandler(SIGSEGV, sigsegv, SA_RESETHAND);
 	if (sigsetjmp(jmpbuf, 1) != 0) {
-		return false;
+		return RET_FAULTED;
 	} else {
-		asm volatile ("sti");
-		return true;
+		asm volatile("sti; pushf; pop %[flags]"
+				: [flags] "=rm" (flags));
+
+		/* X86_FLAGS_IF */
+		if (irqs_off && (flags & (1 << 9)))
+			return RET_FAIL;
+		else
+			return RET_EMUL;
 	}
 	clearhandler(SIGSEGV);
 }
 
-static void expect_gp_sti(void)
+static void expect_gp_sti(bool irqs_off)
 {
-	if (try_sti()) {
+	int ret = try_sti(irqs_off);
+
+	switch (ret) {
+	case RET_FAULTED:
+		printf("[OK]\tSTI faulted\n");
+		break;
+	case RET_EMUL:
+		printf("[OK]\tSTI NOPped\n");
+		break;
+	default:
 		printf("[FAIL]\tSTI worked\n");
 		nerrs++;
-	} else {
-		printf("[OK]\tSTI faulted\n");
 	}
 }
 
-static void expect_gp_cli(void)
+/*
+ * Returns whether it managed to disable interrupts.
+ */
+static bool test_cli(void)
 {
-	if (try_cli()) {
+	int ret = try_cli();
+
+	switch (ret) {
+	case RET_FAULTED:
+		printf("[OK]\tCLI faulted\n");
+		break;
+	case RET_EMUL:
+		printf("[OK]\tCLI NOPped\n");
+		break;
+	default:
 		printf("[FAIL]\tCLI worked\n");
 		nerrs++;
-	} else {
-		printf("[OK]\tCLI faulted\n");
+		return true;
 	}
+
+	return false;
 }
 
 int main(void)
@@ -152,8 +192,7 @@
 	}
 
 	/* Make sure that CLI/STI are blocked even with IOPL level 3 */
-	expect_gp_cli();
-	expect_gp_sti();
+	expect_gp_sti(test_cli());
 	expect_ok_outb(0x80);
 
 	/* Establish an I/O bitmap to test the restore */
@@ -204,8 +243,7 @@
 	printf("[RUN]\tparent: write to 0x80 (should fail)\n");
 
 	expect_gp_outb(0x80);
-	expect_gp_cli();
-	expect_gp_sti();
+	expect_gp_sti(test_cli());
 
 	/* Test the capability checks. */
 	printf("\tiopl(3)\n");
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/x86/test_vsyscall.c
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/x86/test_vsyscall.c
@@ -497,7 +497,7 @@
 	}
 
 	if (vsyscall_map_r) {
-		if (!memcmp(buf, (const void *)0xffffffffff600000, 4096)) {
+		if (!memcmp(buf, remote.iov_base, sizeof(buf))) {
 			printf("[OK]\tIt worked and read correct data\n");
 		} else {
 			printf("[FAIL]\tIt worked but returned incorrect data\n");
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/zram/zram.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/zram/zram.sh
@@ -2,9 +2,6 @@
 # SPDX-License-Identifier: GPL-2.0
 TCID="zram.sh"
 
-# Kselftest framework requirement - SKIP code is 4.
-ksft_skip=4
-
 . ./zram_lib.sh
 
 run_zram () {
@@ -18,14 +15,4 @@
 
 check_prereqs
 
-# check zram module exists
-MODULE_PATH=/lib/modules/`uname -r`/kernel/drivers/block/zram/zram.ko
-if [ -f $MODULE_PATH ]; then
-	run_zram
-elif [ -b /dev/zram0 ]; then
-	run_zram
-else
-	echo "$TCID : No zram.ko module or /dev/zram0 device file not found"
-	echo "$TCID : CONFIG_ZRAM is not set"
-	exit $ksft_skip
-fi
+run_zram
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/zram/zram01.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/zram/zram01.sh
@@ -33,9 +33,7 @@
 
 zram_fill_fs()
 {
-	local mem_free0=$(free -m | awk 'NR==2 {print $4}')
-
-	for i in $(seq 0 $(($dev_num - 1))); do
+	for i in $(seq $dev_start $dev_end); do
 		echo "fill zram$i..."
 		local b=0
 		while [ true ]; do
@@ -45,29 +43,17 @@
 			b=$(($b + 1))
 		done
 		echo "zram$i can be filled with '$b' KB"
-	done
 
-	local mem_free1=$(free -m | awk 'NR==2 {print $4}')
-	local used_mem=$(($mem_free0 - $mem_free1))
+		local mem_used_total=`awk '{print $3}' "/sys/block/zram$i/mm_stat"`
+		local v=$((100 * 1024 * $b / $mem_used_total))
+		if [ "$v" -lt 100 ]; then
+			 echo "FAIL compression ratio: 0.$v:1"
+			 ERR_CODE=-1
+			 return
+		fi
 
-	local total_size=0
-	for sm in $zram_sizes; do
-		local s=$(echo $sm | sed 's/M//')
-		total_size=$(($total_size + $s))
+		echo "zram compression ratio: $(echo "scale=2; $v / 100 " | bc):1: OK"
 	done
-
-	echo "zram used ${used_mem}M, zram disk sizes ${total_size}M"
-
-	local v=$((100 * $total_size / $used_mem))
-
-	if [ "$v" -lt 100 ]; then
-		echo "FAIL compression ratio: 0.$v:1"
-		ERR_CODE=-1
-		zram_cleanup
-		return
-	fi
-
-	echo "zram compression ratio: $(echo "scale=2; $v / 100 " | bc):1: OK"
 }
 
 check_prereqs
@@ -81,7 +67,6 @@
 
 zram_fill_fs
 zram_cleanup
-zram_unload
 
 if [ $ERR_CODE -ne 0 ]; then
 	echo "$TCID : [FAIL]"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/zram/zram02.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/zram/zram02.sh
@@ -36,7 +36,6 @@
 zram_makeswap
 zram_swapoff
 zram_cleanup
-zram_unload
 
 if [ $ERR_CODE -ne 0 ]; then
 	echo "$TCID : [FAIL]"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/testing/selftests/zram/zram_lib.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/testing/selftests/zram/zram_lib.sh
@@ -5,12 +5,17 @@
 # Author: Alexey Kodanev <alexey.kodanev@oracle.com>
 # Modified: Naresh Kamboju <naresh.kamboju@linaro.org>
 
-MODULE=0
 dev_makeswap=-1
 dev_mounted=-1
-
+dev_start=0
+dev_end=-1
+module_load=-1
+sys_control=-1
 # Kselftest framework requirement - SKIP code is 4.
 ksft_skip=4
+kernel_version=`uname -r | cut -d'.' -f1,2`
+kernel_major=${kernel_version%.*}
+kernel_minor=${kernel_version#*.}
 
 trap INT
 
@@ -25,68 +30,104 @@
 	fi
 }
 
+kernel_gte()
+{
+	major=${1%.*}
+	minor=${1#*.}
+
+	if [ $kernel_major -gt $major ]; then
+		return 0
+	elif [[ $kernel_major -eq $major && $kernel_minor -ge $minor ]]; then
+		return 0
+	fi
+
+	return 1
+}
+
 zram_cleanup()
 {
 	echo "zram cleanup"
 	local i=
-	for i in $(seq 0 $dev_makeswap); do
+	for i in $(seq $dev_start $dev_makeswap); do
 		swapoff /dev/zram$i
 	done
 
-	for i in $(seq 0 $dev_mounted); do
+	for i in $(seq $dev_start $dev_mounted); do
 		umount /dev/zram$i
 	done
 
-	for i in $(seq 0 $(($dev_num - 1))); do
+	for i in $(seq $dev_start $dev_end); do
 		echo 1 > /sys/block/zram${i}/reset
 		rm -rf zram$i
 	done
 
-}
+	if [ $sys_control -eq 1 ]; then
+		for i in $(seq $dev_start $dev_end); do
+			echo $i > /sys/class/zram-control/hot_remove
+		done
+	fi
 
-zram_unload()
-{
-	if [ $MODULE -ne 0 ] ; then
-		echo "zram rmmod zram"
+	if [ $module_load -eq 1 ]; then
 		rmmod zram > /dev/null 2>&1
 	fi
 }
 
 zram_load()
 {
-	# check zram module exists
-	MODULE_PATH=/lib/modules/`uname -r`/kernel/drivers/block/zram/zram.ko
-	if [ -f $MODULE_PATH ]; then
-		MODULE=1
-		echo "create '$dev_num' zram device(s)"
-		modprobe zram num_devices=$dev_num
-		if [ $? -ne 0 ]; then
-			echo "failed to insert zram module"
-			exit 1
-		fi
+	echo "create '$dev_num' zram device(s)"
 
-		dev_num_created=$(ls /dev/zram* | wc -w)
+	# zram module loaded, new kernel
+	if [ -d "/sys/class/zram-control" ]; then
+		echo "zram modules already loaded, kernel supports" \
+			"zram-control interface"
+		dev_start=$(ls /dev/zram* | wc -w)
+		dev_end=$(($dev_start + $dev_num - 1))
+		sys_control=1
+
+		for i in $(seq $dev_start $dev_end); do
+			cat /sys/class/zram-control/hot_add > /dev/null
+		done
+
+		echo "all zram devices (/dev/zram$dev_start~$dev_end" \
+			"successfully created"
+		return 0
+	fi
 
-		if [ "$dev_num_created" -ne "$dev_num" ]; then
-			echo "unexpected num of devices: $dev_num_created"
-			ERR_CODE=-1
+	# detect old kernel or built-in
+	modprobe zram num_devices=$dev_num
+	if [ ! -d "/sys/class/zram-control" ]; then
+		if grep -q '^zram' /proc/modules; then
+			rmmod zram > /dev/null 2>&1
+			if [ $? -ne 0 ]; then
+				echo "zram module is being used on old kernel" \
+					"without zram-control interface"
+				exit $ksft_skip
+			fi
 		else
-			echo "zram load module successful"
+			echo "test needs CONFIG_ZRAM=m on old kernel without" \
+				"zram-control interface"
+			exit $ksft_skip
 		fi
-	elif [ -b /dev/zram0 ]; then
-		echo "/dev/zram0 device file found: OK"
-	else
-		echo "ERROR: No zram.ko module or no /dev/zram0 device found"
-		echo "$TCID : CONFIG_ZRAM is not set"
-		exit 1
+		modprobe zram num_devices=$dev_num
 	fi
+
+	module_load=1
+	dev_end=$(($dev_num - 1))
+	echo "all zram devices (/dev/zram0~$dev_end) successfully created"
 }
 
 zram_max_streams()
 {
 	echo "set max_comp_streams to zram device(s)"
 
-	local i=0
+	kernel_gte 4.7
+	if [ $? -eq 0 ]; then
+		echo "The device attribute max_comp_streams was"\
+		               "deprecated in 4.7"
+		return 0
+	fi
+
+	local i=$dev_start
 	for max_s in $zram_max_streams; do
 		local sys_path="/sys/block/zram${i}/max_comp_streams"
 		echo $max_s > $sys_path || \
@@ -98,7 +139,7 @@
 			echo "FAIL can't set max_streams '$max_s', get $max_stream"
 
 		i=$(($i + 1))
-		echo "$sys_path = '$max_streams' ($i/$dev_num)"
+		echo "$sys_path = '$max_streams'"
 	done
 
 	echo "zram max streams: OK"
@@ -108,15 +149,16 @@
 {
 	echo "test that we can set compression algorithm"
 
-	local algs=$(cat /sys/block/zram0/comp_algorithm)
+	local i=$dev_start
+	local algs=$(cat /sys/block/zram${i}/comp_algorithm)
 	echo "supported algs: $algs"
-	local i=0
+
 	for alg in $zram_algs; do
 		local sys_path="/sys/block/zram${i}/comp_algorithm"
 		echo "$alg" >	$sys_path || \
 			echo "FAIL can't set '$alg' to $sys_path"
 		i=$(($i + 1))
-		echo "$sys_path = '$alg' ($i/$dev_num)"
+		echo "$sys_path = '$alg'"
 	done
 
 	echo "zram set compression algorithm: OK"
@@ -125,14 +167,14 @@
 zram_set_disksizes()
 {
 	echo "set disk size to zram device(s)"
-	local i=0
+	local i=$dev_start
 	for ds in $zram_sizes; do
 		local sys_path="/sys/block/zram${i}/disksize"
 		echo "$ds" >	$sys_path || \
 			echo "FAIL can't set '$ds' to $sys_path"
 
 		i=$(($i + 1))
-		echo "$sys_path = '$ds' ($i/$dev_num)"
+		echo "$sys_path = '$ds'"
 	done
 
 	echo "zram set disksizes: OK"
@@ -142,14 +184,14 @@
 {
 	echo "set memory limit to zram device(s)"
 
-	local i=0
+	local i=$dev_start
 	for ds in $zram_mem_limits; do
 		local sys_path="/sys/block/zram${i}/mem_limit"
 		echo "$ds" >	$sys_path || \
 			echo "FAIL can't set '$ds' to $sys_path"
 
 		i=$(($i + 1))
-		echo "$sys_path = '$ds' ($i/$dev_num)"
+		echo "$sys_path = '$ds'"
 	done
 
 	echo "zram set memory limit: OK"
@@ -158,8 +200,8 @@
 zram_makeswap()
 {
 	echo "make swap with zram device(s)"
-	local i=0
-	for i in $(seq 0 $(($dev_num - 1))); do
+	local i=$dev_start
+	for i in $(seq $dev_start $dev_end); do
 		mkswap /dev/zram$i > err.log 2>&1
 		if [ $? -ne 0 ]; then
 			cat err.log
@@ -182,7 +224,7 @@
 zram_swapoff()
 {
 	local i=
-	for i in $(seq 0 $dev_makeswap); do
+	for i in $(seq $dev_start $dev_end); do
 		swapoff /dev/zram$i > err.log 2>&1
 		if [ $? -ne 0 ]; then
 			cat err.log
@@ -196,7 +238,7 @@
 
 zram_makefs()
 {
-	local i=0
+	local i=$dev_start
 	for fs in $zram_filesystems; do
 		# if requested fs not supported default it to ext2
 		which mkfs.$fs > /dev/null 2>&1 || fs=ext2
@@ -215,7 +257,7 @@
 zram_mount()
 {
 	local i=0
-	for i in $(seq 0 $(($dev_num - 1))); do
+	for i in $(seq $dev_start $dev_end); do
 		echo "mount /dev/zram$i"
 		mkdir zram$i
 		mount /dev/zram$i zram$i > /dev/null || \
--- linux-xilinx-zynqmp-5.15.0.orig/tools/thermal/tmon/sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/tools/thermal/tmon/sysfs.c
@@ -13,6 +13,7 @@
 #include <stdint.h>
 #include <dirent.h>
 #include <libintl.h>
+#include <limits.h>
 #include <ctype.h>
 #include <time.h>
 #include <syslog.h>
@@ -33,9 +34,9 @@
 {
 	FILE *fd;
 	int ret = -1;
-	char filepath[256];
+	char filepath[PATH_MAX + 2]; /* NUL and '/' */
 
-	snprintf(filepath, 256, "%s/%s", path, filename);
+	snprintf(filepath, sizeof(filepath), "%s/%s", path, filename);
 
 	fd = fopen(filepath, "w");
 	if (!fd) {
@@ -57,9 +58,9 @@
 {
 	FILE *fd;
 	int ret = -1;
-	char filepath[256];
+	char filepath[PATH_MAX + 2]; /* NUL and '/' */
 
-	snprintf(filepath, 256, "%s/%s", path, filename);
+	snprintf(filepath, sizeof(filepath), "%s/%s", path, filename);
 
 	fd = fopen(filepath, "r");
 	if (!fd) {
@@ -76,9 +77,9 @@
 {
 	FILE *fd;
 	int ret = -1;
-	char filepath[256];
+	char filepath[PATH_MAX + 2]; /* NUL and '/' */
 
-	snprintf(filepath, 256, "%s/%s", path, filename);
+	snprintf(filepath, sizeof(filepath), "%s/%s", path, filename);
 
 	fd = fopen(filepath, "r");
 	if (!fd) {
@@ -199,8 +200,8 @@
 {
 	unsigned long trip_instance = 0;
 	char cdev_name_linked[256];
-	char cdev_name[256];
-	char cdev_trip_name[256];
+	char cdev_name[PATH_MAX];
+	char cdev_trip_name[PATH_MAX];
 	int cdev_id;
 
 	if (nl->d_type == DT_LNK) {
@@ -213,7 +214,8 @@
 			return -EINVAL;
 		}
 		/* find the link to real cooling device record binding */
-		snprintf(cdev_name, 256, "%s/%s", tz_name, nl->d_name);
+		snprintf(cdev_name, sizeof(cdev_name) - 2, "%s/%s",
+			 tz_name, nl->d_name);
 		memset(cdev_name_linked, 0, sizeof(cdev_name_linked));
 		if (readlink(cdev_name, cdev_name_linked,
 				sizeof(cdev_name_linked) - 1) != -1) {
@@ -226,8 +228,8 @@
 			/* find the trip point in which the cdev is binded to
 			 * in this tzone
 			 */
-			snprintf(cdev_trip_name, 256, "%s%s", nl->d_name,
-				"_trip_point");
+			snprintf(cdev_trip_name, sizeof(cdev_trip_name) - 1,
+				"%s%s", nl->d_name, "_trip_point");
 			sysfs_get_ulong(tz_name, cdev_trip_name,
 					&trip_instance);
 			/* validate trip point range, e.g. trip could return -1
--- linux-xilinx-zynqmp-5.15.0.orig/tools/thermal/tmon/tmon.h
+++ linux-xilinx-zynqmp-5.15.0/tools/thermal/tmon/tmon.h
@@ -27,6 +27,9 @@
 #define NR_LINES_TZDATA 1
 #define TMON_LOG_FILE "/var/tmp/tmon.log"
 
+#include <sys/time.h>
+#include <pthread.h>
+
 extern unsigned long ticktime;
 extern double time_elapsed;
 extern unsigned long target_temp_user;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/tracing/latency/latency-collector.c
+++ linux-xilinx-zynqmp-5.15.0/tools/tracing/latency/latency-collector.c
@@ -935,12 +935,12 @@
 	}
 
 	if (!tracers) {
-		warnx(no_tracer_msg);
+		warnx("%s", no_tracer_msg);
 		return;
 	}
 
 	if (!found) {
-		warnx(no_latency_tr_msg);
+		warnx("%s", no_latency_tr_msg);
 		tracefs_list_free(tracers);
 		return;
 	}
@@ -983,7 +983,7 @@
 	for (i = 0; relevant_tracers[i]; i++) {
 		valid = tracer_valid(relevant_tracers[i], &notracer);
 		if (notracer)
-			errx(EXIT_FAILURE, no_tracer_msg);
+			errx(EXIT_FAILURE, "%s", no_tracer_msg);
 		if (valid)
 			return relevant_tracers[i];
 	}
@@ -1538,7 +1538,7 @@
 				mutex_lock(&print_mtx);
 				check_signals();
 				write_or_die(fd_stdout, queue_full_warning,
-					     sizeof(queue_full_warning));
+					     strlen(queue_full_warning));
 				mutex_unlock(&print_mtx);
 			}
 			modified--;
@@ -1878,7 +1878,7 @@
 			}
 			valid = tracer_valid(current_tracer, &notracer);
 			if (notracer)
-				errx(EXIT_FAILURE, no_tracer_msg);
+				errx(EXIT_FAILURE, "%s", no_tracer_msg);
 			if (!valid)
 				errx(EXIT_FAILURE,
 "The tracer %s is not supported by your kernel!\n", current_tracer);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/usb/usbip/configure.ac
+++ linux-xilinx-zynqmp-5.15.0/tools/usb/usbip/configure.ac
@@ -18,7 +18,7 @@
 # Silent build for automake >= 1.11
 m4_ifdef([AM_SILENT_RULES], [AM_SILENT_RULES([yes])])
 
-AC_SUBST([EXTRA_CFLAGS], ["-Wall -Werror -Wextra -std=gnu99"])
+AC_SUBST([EXTRA_CFLAGS], ["-Wall -Werror -Wextra -Wno-address-of-packed-member -std=gnu99"])
 
 # Checks for programs.
 AC_PROG_CC
--- linux-xilinx-zynqmp-5.15.0.orig/tools/usb/usbip/src/usbip_detach.c
+++ linux-xilinx-zynqmp-5.15.0/tools/usb/usbip/src/usbip_detach.c
@@ -68,6 +68,7 @@
 	}
 
 	if (!found) {
+		ret = -1;
 		err("Invalid port %s > maxports %d",
 			port, vhci_driver->nports);
 		goto call_driver_close;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/Makefile
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/Makefile
@@ -5,7 +5,8 @@
 vringh_test: vringh_test.o vringh.o virtio_ring.o
 
 CFLAGS += -g -O2 -Werror -Wno-maybe-uninitialized -Wall -I. -I../include/ -I ../../usr/include/ -Wno-pointer-sign -fno-strict-overflow -fno-strict-aliasing -fno-common -MMD -U_FORTIFY_SOURCE -include ../../include/linux/kconfig.h
-LDFLAGS += -lpthread
+CFLAGS += -pthread
+LDFLAGS += -pthread
 vpath %.c ../../drivers/virtio ../../drivers/vhost
 mod:
 	${MAKE} -C `pwd`/../.. M=`pwd`/vhost_test V=${V}
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/bug.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/bug.h
@@ -1,13 +1,11 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-#ifndef BUG_H
-#define BUG_H
+#ifndef _LINUX_BUG_H
+#define _LINUX_BUG_H
 
 #include <asm/bug.h>
 
 #define BUG_ON(__BUG_ON_cond) assert(!(__BUG_ON_cond))
 
-#define BUILD_BUG_ON(x)
-
 #define BUG() abort()
 
-#endif /* BUG_H */
+#endif /* _LINUX_BUG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/build_bug.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/build_bug.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_BUILD_BUG_H
+#define _LINUX_BUILD_BUG_H
+
+#define BUILD_BUG_ON(x)
+
+#endif	/* _LINUX_BUILD_BUG_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/cpumask.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/cpumask.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_CPUMASK_H
+#define _LINUX_CPUMASK_H
+
+#include <linux/kernel.h>
+
+#endif /* _LINUX_CPUMASK_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/gfp.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/gfp.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LINUX_GFP_H
+#define __LINUX_GFP_H
+
+#include <linux/topology.h>
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/kernel.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/kernel.h
@@ -10,6 +10,7 @@
 #include <stdarg.h>
 
 #include <linux/compiler.h>
+#include <linux/log2.h>
 #include <linux/types.h>
 #include <linux/overflow.h>
 #include <linux/list.h>
@@ -29,7 +30,6 @@
 #define READ                    0
 #define WRITE                   1
 
-typedef unsigned long long phys_addr_t;
 typedef unsigned long long dma_addr_t;
 typedef size_t __kernel_size_t;
 typedef unsigned int __wsum;
@@ -136,6 +136,7 @@
 #endif
 #define dev_err(dev, format, ...) fprintf (stderr, format, ## __VA_ARGS__)
 #define dev_warn(dev, format, ...) fprintf (stderr, format, ## __VA_ARGS__)
+#define dev_warn_once(dev, format, ...) fprintf (stderr, format, ## __VA_ARGS__)
 
 #define min(x, y) ({				\
 	typeof(x) _min1 = (x);			\
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/kmsan.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/kmsan.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_KMSAN_H
+#define _LINUX_KMSAN_H
+
+#include <linux/gfp.h>
+
+inline void kmsan_handle_dma(struct page *page, size_t offset, size_t size,
+			     enum dma_data_direction dir)
+{
+}
+
+#endif /* _LINUX_KMSAN_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/scatterlist.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/scatterlist.h
@@ -2,6 +2,7 @@
 #ifndef SCATTERLIST_H
 #define SCATTERLIST_H
 #include <linux/kernel.h>
+#include <linux/bug.h>
 
 struct scatterlist {
 	unsigned long	page_link;
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/topology.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/topology.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_TOPOLOGY_H
+#define _LINUX_TOPOLOGY_H
+
+#include <linux/cpumask.h>
+
+#endif /* _LINUX_TOPOLOGY_H */
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/linux/vringh.h
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/linux/vringh.h
@@ -1 +1,2 @@
+#include <limits.h>
 #include "../../../include/linux/vringh.h"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/virtio_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/virtio_test.c
@@ -130,6 +130,7 @@
 	memset(dev, 0, sizeof *dev);
 	dev->vdev.features = features;
 	INIT_LIST_HEAD(&dev->vdev.vqs);
+	spin_lock_init(&dev->vdev.vqs_list_lock);
 	dev->buf_size = 1024;
 	dev->buf = malloc(dev->buf_size);
 	assert(dev->buf);
--- linux-xilinx-zynqmp-5.15.0.orig/tools/virtio/vringh_test.c
+++ linux-xilinx-zynqmp-5.15.0/tools/virtio/vringh_test.c
@@ -308,6 +308,7 @@
 
 		gvdev.vdev.features = features;
 		INIT_LIST_HEAD(&gvdev.vdev.vqs);
+		spin_lock_init(&gvdev.vdev.vqs_list_lock);
 		gvdev.to_host_fd = to_host[1];
 		gvdev.notifies = 0;
 
@@ -455,6 +456,7 @@
 	getrange = getrange_iov;
 	vdev.features = 0;
 	INIT_LIST_HEAD(&vdev.vqs);
+	spin_lock_init(&vdev.vqs_list_lock);
 
 	while (argv[1]) {
 		if (strcmp(argv[1], "--indirect") == 0)
--- linux-xilinx-zynqmp-5.15.0.orig/tools/vm/slabinfo-gnuplot.sh
+++ linux-xilinx-zynqmp-5.15.0/tools/vm/slabinfo-gnuplot.sh
@@ -150,7 +150,7 @@
 	let lines=3
 	out=`basename "$in"`"-slabs-by-loss"
 	`cat "$in" | grep -A "$lines" 'Slabs sorted by loss' |\
-		egrep -iv '\-\-|Name|Slabs'\
+		grep -E -iv '\-\-|Name|Slabs'\
 		| awk '{print $1" "$4+$2*$3" "$4}' > "$out"`
 	if [ $? -eq 0 ]; then
 		do_slabs_plotting "$out"
@@ -159,7 +159,7 @@
 	let lines=3
 	out=`basename "$in"`"-slabs-by-size"
 	`cat "$in" | grep -A "$lines" 'Slabs sorted by size' |\
-		egrep -iv '\-\-|Name|Slabs'\
+		grep -E -iv '\-\-|Name|Slabs'\
 		| awk '{print $1" "$4" "$4-$2*$3}' > "$out"`
 	if [ $? -eq 0 ]; then
 		do_slabs_plotting "$out"
--- linux-xilinx-zynqmp-5.15.0.orig/tools/vm/slabinfo.c
+++ linux-xilinx-zynqmp-5.15.0/tools/vm/slabinfo.c
@@ -125,7 +125,7 @@
 		"-n|--numa              Show NUMA information\n"
 		"-N|--lines=K           Show the first K slabs\n"
 		"-o|--ops               Show kmem_cache_ops\n"
-		"-P|--partial		Sort by number of partial slabs\n"
+		"-P|--partial           Sort by number of partial slabs\n"
 		"-r|--report            Detailed report on single slabs\n"
 		"-s|--shrink            Shrink slabs\n"
 		"-S|--Size              Sort by size\n"
@@ -233,6 +233,24 @@
 	return l;
 }
 
+static unsigned long read_debug_slab_obj(struct slabinfo *s, const char *name)
+{
+	char x[128];
+	FILE *f;
+	size_t l;
+
+	snprintf(x, 128, "/sys/kernel/debug/slab/%s/%s", s->name, name);
+	f = fopen(x, "r");
+	if (!f) {
+		buffer[0] = 0;
+		l = 0;
+	} else {
+		l = fread(buffer, 1, sizeof(buffer), f);
+		buffer[l] = 0;
+		fclose(f);
+	}
+	return l;
+}
 
 /*
  * Put a size string together
@@ -409,14 +427,18 @@
 {
 	printf("\n%s: Kernel object allocation\n", s->name);
 	printf("-----------------------------------------------------------------------\n");
-	if (read_slab_obj(s, "alloc_calls"))
+	if (read_debug_slab_obj(s, "alloc_traces"))
+		printf("%s", buffer);
+	else if (read_slab_obj(s, "alloc_calls"))
 		printf("%s", buffer);
 	else
 		printf("No Data\n");
 
 	printf("\n%s: Kernel object freeing\n", s->name);
 	printf("------------------------------------------------------------------------\n");
-	if (read_slab_obj(s, "free_calls"))
+	if (read_debug_slab_obj(s, "free_traces"))
+		printf("%s", buffer);
+	else if (read_slab_obj(s, "free_calls"))
 		printf("%s", buffer);
 	else
 		printf("No Data\n");
@@ -1045,15 +1067,27 @@
 		for (s2 = s1 + 1; s2 < slabinfo + slabs; s2++) {
 			int result;
 
-			if (sort_size)
-				result = slab_size(s1) < slab_size(s2);
-			else if (sort_active)
-				result = slab_activity(s1) < slab_activity(s2);
-			else if (sort_loss)
-				result = slab_waste(s1) < slab_waste(s2);
-			else if (sort_partial)
-				result = s1->partial < s2->partial;
-			else
+			if (sort_size) {
+				if (slab_size(s1) == slab_size(s2))
+					result = strcasecmp(s1->name, s2->name);
+				else
+					result = slab_size(s1) < slab_size(s2);
+			} else if (sort_active) {
+				if (slab_activity(s1) == slab_activity(s2))
+					result = strcasecmp(s1->name, s2->name);
+				else
+					result = slab_activity(s1) < slab_activity(s2);
+			} else if (sort_loss) {
+				if (slab_waste(s1) == slab_waste(s2))
+					result = strcasecmp(s1->name, s2->name);
+				else
+					result = slab_waste(s1) < slab_waste(s2);
+			} else if (sort_partial) {
+				if (s1->partial == s2->partial)
+					result = strcasecmp(s1->name, s2->name);
+				else
+					result = s1->partial < s2->partial;
+			} else
 				result = strcasecmp(s1->name, s2->name);
 
 			if (show_inverted)
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/Kconfig
@@ -0,0 +1,31 @@
+menu "Ubuntu Supplied Third-Party Device Drivers"
+
+
+config UBUNTU_ODM_DRIVERS
+	def_bool $(success,$(srctree)/debian/scripts/misc/arch-has-odm-enabled.sh $(DEB_ARCH))
+	help
+	  Turn on support for Ubuntu ODM supplied drivers
+
+#
+# NOTE: to allow drivers to be added and removed without causing merge
+# collisions you should add new entries in the middle of the six lines
+# of ## at the bottom of the list.  Always add three lines of ## above
+# your new entry and maintain the six lines below.
+#
+
+##
+##
+##
+source "ubuntu/ubuntu-host/Kconfig"
+##
+##
+##
+source "ubuntu/staging/Kconfig"
+##
+##
+##
+##
+##
+##
+
+endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/Makefile
@@ -0,0 +1,31 @@
+#
+# Makefile for the Linux kernel ubuntu supplied third-party device drivers.
+#
+
+#
+# NOTE: to allow drivers to be added and removed without causing merge
+# collisions you should add new entries in the middle of the six lines
+# of ## at the bottom of the list.  Always add three lines of ## above
+# your new entry and maintain the six lines below.
+#
+
+##
+##
+##
+##
+##
+##
+obj-y += staging/
+##
+##
+##
+obj-$(CONFIG_UBUNTU_HOST)      += ubuntu-host/
+##
+##
+##
+##
+##
+##
+
+# This is a stupid trick to get kbuild to create ubuntu/built-in.o
+obj- += foo.o
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/include/Kbuild
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/include/Kbuild
@@ -0,0 +1,2 @@
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/include/README
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/include/README
@@ -0,0 +1,4 @@
+Only use this directory for things which need to share their headers with
+other parts of the kernel or other modules in ubuntu/
+
+Otherwise, keep them local to the module directory.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/Kconfig
@@ -0,0 +1,25 @@
+menu "experimental"
+
+#
+# NOTE: to allow drivers to be added and removed without causing merge
+# collisions you should add new entries in the middle of the six lines
+# of ## at the bottom of the list.  Always add three lines of ## above
+# your new entry and maintain the six lines below.
+#
+
+##
+##
+##
+source "ubuntu/staging/mali/Kconfig"
+##
+##
+##
+source "ubuntu/staging/xilinx-mv-camera-10gige-module/Kconfig"
+##
+##
+##
+##
+##
+##
+
+endmenu
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/Makefile
@@ -0,0 +1,46 @@
+#
+# Makefile for the Linux kernel ubuntu/staging supplied third-party device
+# drivers.
+#
+
+#
+# NOTE: to allow drivers to be added and removed without causing merge
+# collisions you should add new entries in the middle of the six lines
+# of ## at the bottom of the list.  Always add three lines of ## above
+# your new entry and maintain the six lines below.
+#
+
+
+##
+##
+##
+##
+##
+##
+obj-$(CONFIG_MALI400) += mali/
+##
+##
+##
+obj-y += xilinx-vcu/
+##
+##
+##
+obj-y += xilinx-hdmi/
+##
+##
+##
+obj-$(CONFIG_NET_VENDOR_S2I) += xilinx-mv-camera-10gige-module/
+##
+##
+##
+obj-y += xilinx-mv-camera-sensor-module/
+##
+##
+##
+obj-y += xilinx-isp-module/
+##
+##
+##
+##
+##
+##
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/Kbuild
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/Kbuild
@@ -0,0 +1,258 @@
+#
+# Copyright (C) 2010-2011 ARM Limited. All rights reserved.
+# 
+# This program is free software and is provided to you under the terms of the GNU General Public License version 2
+# as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+# 
+# A copy of the licence is included with the program, and can also be obtained from Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+#
+
+# This file is called by the Linux build system.
+
+# set up defaults if not defined by the user
+TIMESTAMP ?= default
+OS_MEMORY_KERNEL_BUFFER_SIZE_IN_MB ?= 16
+USING_GPU_UTILIZATION ?= 0
+PROFILING_SKIP_PP_JOBS ?= 0
+PROFILING_SKIP_PP_AND_GP_JOBS ?= 0
+MALI_PP_SCHEDULER_FORCE_NO_JOB_OVERLAP ?= 0
+MALI_PP_SCHEDULER_KEEP_SUB_JOB_STARTS_ALIGNED ?= 0
+MALI_PP_SCHEDULER_FORCE_NO_JOB_OVERLAP_BETWEEN_APPS ?= 0
+MALI_UPPER_HALF_SCHEDULING ?= 1
+MALI_ENABLE_CPU_CYCLES ?= 0
+HAVE_UNLOCKED_IOCTL ?= 1
+
+# For customer releases the Linux Device Drivers will be provided as ARM proprietary and GPL releases:
+# The ARM proprietary product will only include the license/proprietary directory
+# The GPL product will only include the license/gpl directory
+ifeq ($(wildcard $(srctree)/$(src)/linux/license/gpl/*),)
+    ccflags-y += -I$(srctree)/$(src)/linux/license/proprietary
+    ifeq ($(CONFIG_MALI400_PROFILING),y)
+        $(error Profiling is incompatible with non-GPL license)
+    endif
+    ifeq ($(CONFIG_PM_RUNTIME),y)
+        $(error Runtime PM is incompatible with non-GPL license)
+    endif
+    ifeq ($(CONFIG_DMA_SHARED_BUFFER),y)
+        $(error DMA-BUF is incompatible with non-GPL license)
+    endif
+    $(error Linux Device integration is incompatible with non-GPL license)
+else
+    ccflags-y += -I$(srctree)/$(src)/linux/license/gpl
+endif
+
+ifeq ($(USING_GPU_UTILIZATION), 1)
+    ifeq ($(USING_DVFS), 1)
+        $(error USING_GPU_UTILIZATION conflict with USING_DVFS you can read the Integration Guide to choose which one do you need)
+    endif
+endif
+
+ifeq ($(MALI_PLATFORM_FILES),)
+ifeq ($(CONFIG_ARCH_ZYNQMP),y)
+EXTRA_DEFINES += -DMALI_FAKE_PLATFORM_DEVICE=1
+export MALI_PLATFORM=arm
+export MALI_PLATFORM_FILES_BUILDIN = $(notdir $(wildcard $(srctree)/$(src)/platform/$(MALI_PLATFORM)/*.c))
+export MALI_PLATFORM_FILES_ADD_PREFIX = $(addprefix platform/$(MALI_PLATFORM)/,$(MALI_PLATFORM_FILES_BUILDIN)) 
+endif
+endif
+
+mali-y += \
+	linux/mali_osk_atomics.o \
+	linux/mali_osk_irq.o \
+	linux/mali_osk_wq.o \
+	linux/mali_osk_locks.o \
+	linux/mali_osk_wait_queue.o \
+	linux/mali_osk_low_level_mem.o \
+	linux/mali_osk_math.o \
+	linux/mali_osk_memory.o \
+	linux/mali_osk_misc.o \
+	linux/mali_osk_mali.o \
+	linux/mali_osk_notification.o \
+	linux/mali_osk_time.o \
+	linux/mali_osk_timers.o \
+	linux/mali_osk_bitmap.o
+
+mali-y += linux/mali_memory.o linux/mali_memory_os_alloc.o
+mali-y += linux/mali_memory_external.o
+mali-y += linux/mali_memory_block_alloc.o
+mali-y += linux/mali_memory_swap_alloc.o
+
+mali-y += \
+	linux/mali_memory_manager.o \
+	linux/mali_memory_virtual.o \
+	linux/mali_memory_util.o \
+	linux/mali_memory_cow.o \
+	linux/mali_memory_defer_bind.o
+
+mali-y += \
+	linux/mali_ukk_mem.o \
+	linux/mali_ukk_gp.o \
+	linux/mali_ukk_pp.o \
+	linux/mali_ukk_core.o \
+	linux/mali_ukk_soft_job.o \
+	linux/mali_ukk_timeline.o
+
+mali-$(CONFIG_MALI_DEVFREQ) += \
+	linux/mali_devfreq.o \
+	common/mali_pm_metrics.o
+
+# Source files which always are included in a build
+mali-y += \
+	common/mali_kernel_core.o \
+	linux/mali_kernel_linux.o \
+	common/mali_session.o \
+	linux/mali_device_pause_resume.o \
+	common/mali_kernel_vsync.o \
+	linux/mali_ukk_vsync.o \
+	linux/mali_kernel_sysfs.o \
+	common/mali_mmu.o \
+	common/mali_mmu_page_directory.o \
+	common/mali_mem_validation.o \
+	common/mali_hw_core.o \
+	common/mali_gp.o \
+	common/mali_pp.o \
+	common/mali_pp_job.o \
+	common/mali_gp_job.o \
+	common/mali_soft_job.o \
+	common/mali_scheduler.o \
+	common/mali_executor.o \
+	common/mali_group.o \
+	common/mali_dlbu.o \
+	common/mali_broadcast.o \
+	common/mali_pm.o \
+	common/mali_pmu.o \
+	common/mali_user_settings_db.o \
+	common/mali_kernel_utilization.o \
+	common/mali_control_timer.o \
+	common/mali_l2_cache.o \
+	common/mali_timeline.o \
+	common/mali_timeline_fence_wait.o \
+	common/mali_timeline_sync_fence.o \
+	common/mali_spinlock_reentrant.o \
+	common/mali_pm_domain.o \
+	linux/mali_osk_pm.o \
+	linux/mali_pmu_power_up_down.o \
+	__malidrv_build_info.o
+
+ifneq ($(wildcard $(srctree)/$(src)/linux/mali_slp_global_lock.c),)
+	mali-y += linux/mali_slp_global_lock.o
+endif
+
+ifneq ($(MALI_PLATFORM_FILES),)
+	mali-y += $(MALI_PLATFORM_FILES:.c=.o)
+endif
+
+ifneq ($(MALI_PLATFORM_FILES_ADD_PREFIX),)
+	mali-y += $(MALI_PLATFORM_FILES_ADD_PREFIX:.c=.o)
+endif
+
+mali-$(CONFIG_MALI400_PROFILING) += linux/mali_ukk_profiling.o
+mali-$(CONFIG_MALI400_PROFILING) += linux/mali_osk_profiling.o
+
+mali-$(CONFIG_MALI400_INTERNAL_PROFILING) += linux/mali_profiling_internal.o timestamp-$(TIMESTAMP)/mali_timestamp.o
+ccflags-$(CONFIG_MALI400_INTERNAL_PROFILING) += -I$(srctree)/$(src)/timestamp-$(TIMESTAMP)
+
+mali-$(CONFIG_DMA_SHARED_BUFFER) += linux/mali_memory_dma_buf.o
+mali-$(CONFIG_DMA_SHARED_BUFFER) += linux/mali_memory_secure.o
+mali-$(CONFIG_SYNC) += linux/mali_sync.o
+mali-$(CONFIG_SYNC) += linux/mali_internal_sync.o
+mali-$(CONFIG_SYNC_FILE) += linux/mali_sync.o
+mali-$(CONFIG_SYNC_FILE) += linux/mali_internal_sync.o
+mali-$(CONFIG_MALI_DMA_BUF_FENCE) += linux/mali_dma_fence.o
+ccflags-$(CONFIG_SYNC) += -Idrivers/staging/android
+ccflags-$(CONFIG_SYNC_FILE) += -Idrivers/staging/android
+
+mali-$(CONFIG_MALI400_UMP) += linux/mali_memory_ump.o
+
+mali-$(CONFIG_MALI_DVFS) += common/mali_dvfs_policy.o
+
+# Tell the Linux build system from which .o file to create the kernel module
+obj-$(CONFIG_MALI400) := mali.o
+
+ccflags-y += $(EXTRA_DEFINES)
+
+# Set up our defines, which will be passed to gcc
+ccflags-y += -DMALI_PP_SCHEDULER_FORCE_NO_JOB_OVERLAP=$(MALI_PP_SCHEDULER_FORCE_NO_JOB_OVERLAP)
+ccflags-y += -DMALI_PP_SCHEDULER_KEEP_SUB_JOB_STARTS_ALIGNED=$(MALI_PP_SCHEDULER_KEEP_SUB_JOB_STARTS_ALIGNED)
+ccflags-y += -DMALI_PP_SCHEDULER_FORCE_NO_JOB_OVERLAP_BETWEEN_APPS=$(MALI_PP_SCHEDULER_FORCE_NO_JOB_OVERLAP_BETWEEN_APPS)
+ccflags-y += -DMALI_STATE_TRACKING=1
+ccflags-y += -DMALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_MB=$(OS_MEMORY_KERNEL_BUFFER_SIZE_IN_MB)
+ccflags-y += -DUSING_GPU_UTILIZATION=$(USING_GPU_UTILIZATION)
+ccflags-y += -DMALI_ENABLE_CPU_CYCLES=$(MALI_ENABLE_CPU_CYCLES)
+ccflags-y += -DHAVE_UNLOCKED_IOCTL=$(HAVE_UNLOCKED_IOCTL)
+
+ifeq ($(MALI_UPPER_HALF_SCHEDULING),1)
+	ccflags-y += -DMALI_UPPER_HALF_SCHEDULING
+endif
+
+#build-in include path is different
+ifeq ($(MALI_PLATFORM_FILES),)
+ccflags-$(CONFIG_MALI400_UMP) += -I$(srctree)/$(src)/../ump/include/
+else
+ccflags-$(CONFIG_MALI400_UMP) += -I$(srctree)/$(src)/../../ump/include/ump
+endif
+ccflags-$(CONFIG_MALI400_DEBUG) += -DDEBUG
+
+# Use our defines when compiling
+ccflags-y += -I$(srctree)/$(src) -I$(srctree)/$(src)/include -I$(srctree)/$(src)/common -I$(srctree)/$(src)/linux -I$(srctree)/$(src)/platform -Wno-date-time
+
+# Get subversion revision number, fall back to only ${MALI_RELEASE_NAME} if no svn info is available
+MALI_RELEASE_NAME=$(shell cat $(srctree)/$(src)/.version 2> /dev/null)
+
+SVN_INFO = (cd $(srctree)/$(src); svn info 2>/dev/null)
+
+ifneq ($(shell $(SVN_INFO) 2>/dev/null),)
+# SVN detected
+SVN_REV := $(shell $(SVN_INFO) | grep '^Revision: '| sed -e 's/^Revision: //' 2>/dev/null)
+DRIVER_REV := $(MALI_RELEASE_NAME)-r$(SVN_REV)
+CHANGE_DATE := $(shell $(SVN_INFO) | grep '^Last Changed Date: ' | cut -d: -f2- | cut -b2-)
+CHANGED_REVISION := $(shell $(SVN_INFO) | grep '^Last Changed Rev: ' | cut -d: -f2- | cut -b2-)
+REPO_URL := $(shell $(SVN_INFO) | grep '^URL: ' | cut -d: -f2- | cut -b2-)
+
+else # SVN
+GIT_REV := $(shell cd $(srctree)/$(src); git describe --always 2>/dev/null)
+ifneq ($(GIT_REV),)
+# Git detected
+DRIVER_REV := $(MALI_RELEASE_NAME)-$(GIT_REV)
+CHANGE_DATE := $(shell cd $(srctree)/$(src); git log -1 --format="%ci")
+CHANGED_REVISION := $(GIT_REV)
+REPO_URL := $(shell cd $(srctree)/$(src); git describe --all --always 2>/dev/null)
+
+else # Git
+# No Git or SVN detected
+DRIVER_REV := $(MALI_RELEASE_NAME)
+CHANGE_DATE := $(MALI_RELEASE_NAME)
+CHANGED_REVISION := $(MALI_RELEASE_NAME)
+endif
+endif
+
+ccflags-y += -DSVN_REV_STRING=\"$(DRIVER_REV)\"
+
+VERSION_STRINGS :=
+VERSION_STRINGS += API_VERSION=$(shell cd $(srctree)/$(src); grep "\#define _MALI_API_VERSION" $(FILES_PREFIX)include/linux/mali/mali_utgard_uk_types.h | cut -d' ' -f 3 )
+VERSION_STRINGS += REPO_URL=$(REPO_URL)
+VERSION_STRINGS += REVISION=$(DRIVER_REV)
+VERSION_STRINGS += CHANGED_REVISION=$(CHANGED_REVISION)
+VERSION_STRINGS += CHANGE_DATE=$(CHANGE_DATE)
+VERSION_STRINGS += BUILD_DATE=$(shell date)
+ifdef CONFIG_MALI400_DEBUG
+VERSION_STRINGS += BUILD=debug
+else
+VERSION_STRINGS += BUILD=release
+endif
+VERSION_STRINGS += TARGET_PLATFORM=$(TARGET_PLATFORM)
+VERSION_STRINGS += MALI_PLATFORM=$(MALI_PLATFORM)
+VERSION_STRINGS += KDIR=$(KDIR)
+VERSION_STRINGS += OS_MEMORY_KERNEL_BUFFER_SIZE_IN_MB=$(OS_MEMORY_KERNEL_BUFFER_SIZE_IN_MB)
+VERSION_STRINGS += USING_UMP=$(CONFIG_MALI400_UMP)
+VERSION_STRINGS += USING_PROFILING=$(CONFIG_MALI400_PROFILING)
+VERSION_STRINGS += USING_INTERNAL_PROFILING=$(CONFIG_MALI400_INTERNAL_PROFILING)
+VERSION_STRINGS += USING_GPU_UTILIZATION=$(USING_GPU_UTILIZATION)
+VERSION_STRINGS += USING_DVFS=$(CONFIG_MALI_DVFS)
+VERSION_STRINGS += USING_DMA_BUF_FENCE = $(CONFIG_MALI_DMA_BUF_FENCE)
+VERSION_STRINGS += MALI_UPPER_HALF_SCHEDULING=$(MALI_UPPER_HALF_SCHEDULING)
+
+# Create file with Mali driver configuration
+$(src)/__malidrv_build_info.c:
+	@echo 'const char *__malidrv_build_info(void) { return "malidrv: $(VERSION_STRINGS)";}' > $(src)/__malidrv_build_info.c
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/Kconfig
@@ -0,0 +1,117 @@
+config MALI400
+	tristate "Mali-300/400/450 support"
+	depends on ARM || ARM64
+	select DMA_SHARED_BUFFER
+	help
+	  This enables support for the ARM Mali-300, Mali-400, and Mali-450
+	  GPUs.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called mali.
+
+config MALI450
+	bool "Enable Mali-450 support"
+	depends on MALI400
+	help
+	  This enables support for Mali-450 specific features.
+
+config MALI470
+	bool "Enable Mali-470 support"
+	depends on MALI400
+	help
+	  This enables support for Mali-470 specific features.
+
+config MALI400_DEBUG
+	bool "Enable debug in Mali driver"
+	depends on MALI400
+	help
+	  This enabled extra debug checks and messages in the Mali driver.
+
+config MALI400_PROFILING
+	bool "Enable Mali profiling"
+	depends on MALI400
+	select TRACEPOINTS
+	default y
+	help
+	  This enables gator profiling of Mali GPU events.
+
+config MALI400_INTERNAL_PROFILING
+	bool "Enable internal Mali profiling API"
+	depends on MALI400_PROFILING
+	default n
+	help
+	  This enables the internal legacy Mali profiling API.
+
+config MALI400_UMP
+	bool "Enable UMP support"
+	depends on MALI400
+	help
+	  This enables support for the UMP memory sharing API in the Mali driver.
+
+config MALI_DVFS
+	bool "Enable Mali dynamically frequency change"
+	depends on MALI400 && !MALI_DEVFREQ
+	default y
+	help
+	  This enables support for dynamic change frequency of Mali with the goal of lowering power consumption.
+
+config MALI_DMA_BUF_MAP_ON_ATTACH
+	bool "Map dma-buf attachments on attach"
+	depends on MALI400 && DMA_SHARED_BUFFER
+	default y
+	help
+	  This makes the Mali driver map dma-buf attachments after doing
+	  attach. If this is not set the dma-buf attachments will be mapped for
+	  every time the GPU need to access the buffer.
+
+	  Mapping for each access can cause lower performance.
+
+config MALI_SHARED_INTERRUPTS
+	bool "Support for shared interrupts"
+	depends on MALI400
+	default n
+	help
+	  Adds functionality required to properly support shared interrupts.  Without this support,
+	  the device driver will fail during insmod if it detects shared interrupts.  This also
+	  works when the GPU is not using shared interrupts, but might have a slight performance
+	  impact.
+
+config MALI_PMU_PARALLEL_POWER_UP
+	bool "Power up Mali PMU domains in parallel"
+	depends on MALI400
+	default n
+	help
+	  This makes the Mali driver power up all PMU power domains in parallel, instead of
+	  powering up domains one by one, with a slight delay in between. Powering on all power
+	  domains at the same time may cause peak currents higher than what some systems can handle.
+	  These systems must not enable this option.
+
+config MALI_DT
+	bool "Using device tree to initialize module"
+	depends on MALI400 && OF
+	default n
+	help
+	  This enable the Mali driver to choose the device tree path to get platform resoures
+	  and disable the old config method. Mali driver could run on the platform which the
+	  device tree is enabled in kernel and corresponding hardware description is implemented
+	  properly in device DTS file.
+
+config MALI_DEVFREQ
+	bool "Using devfreq to tuning frequency"
+	depends on MALI400 && PM_DEVFREQ
+	default n
+	help
+	Support devfreq for Mali.
+
+	Using the devfreq framework and, by default, the simpleondemand
+	governor, the frequency of Mali will be dynamically selected from the
+	available OPPs.
+
+config MALI_QUIET
+	bool "Make Mali driver very quiet"
+	depends on MALI400 && !MALI400_DEBUG
+	default n
+	help
+	  This forces the Mali driver to never print any messages.
+
+	  If unsure, say N.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/Makefile
@@ -0,0 +1,223 @@
+#
+# Copyright (C) 2010-2016, 2018 ARM Limited. All rights reserved.
+# 
+# This program is free software and is provided to you under the terms of the GNU General Public License version 2
+# as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+# 
+# A copy of the licence is included with the program, and can also be obtained from Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+#
+
+USE_UMPV2=0
+USING_PROFILING ?= 1
+USING_INTERNAL_PROFILING ?= 0
+USING_DVFS ?= 1
+USING_DMA_BUF_FENCE ?= 0
+MALI_HEATMAPS_ENABLED ?= 0
+MALI_DMA_BUF_MAP_ON_ATTACH ?= 1
+MALI_DMA_BUF_LAZY_MAP ?= 0
+MALI_PMU_PARALLEL_POWER_UP ?= 0
+USING_DT ?= 0
+MALI_MEM_SWAP_TRACKING ?= 0
+USING_DEVFREQ ?= 0
+
+# The Makefile sets up "arch" based on the CONFIG, creates the version info
+# string and the __malidrv_build_info.c file, and then call the Linux build
+# system to actually build the driver. After that point the Kbuild file takes
+# over.
+
+# set up defaults if not defined by the user
+ARCH ?= arm
+
+OSKOS=linux
+FILES_PREFIX=
+
+check_cc2 = \
+	$(shell if $(1) -S -o /dev/null -xc /dev/null > /dev/null 2>&1; \
+	then \
+		echo "$(2)"; \
+	else \
+		echo "$(3)"; \
+	fi ;)
+
+# This conditional makefile exports the global definition ARM_INTERNAL_BUILD. Customer releases will not include arm_internal.mak
+-include ../../../arm_internal.mak
+
+# Give warning of old config parameters are used
+ifneq ($(CONFIG),)
+$(warning "You have specified the CONFIG variable which is no longer in used. Use TARGET_PLATFORM instead.")
+endif
+
+ifneq ($(CPU),)
+$(warning "You have specified the CPU variable which is no longer in used. Use TARGET_PLATFORM instead.")
+endif
+
+# Include the mapping between TARGET_PLATFORM and KDIR + MALI_PLATFORM
+-include MALI_CONFIGURATION
+export KDIR ?= $(KDIR-$(TARGET_PLATFORM))
+export MALI_PLATFORM ?= $(MALI_PLATFORM-$(TARGET_PLATFORM))
+
+ifneq ($(TARGET_PLATFORM),)
+ifeq ($(MALI_PLATFORM),)
+$(error "Invalid TARGET_PLATFORM: $(TARGET_PLATFORM)")
+endif
+endif
+
+# validate lookup result
+ifeq ($(KDIR),)
+$(error No KDIR found for platform $(TARGET_PLATFORM))
+endif
+
+ifeq ($(USING_GPU_UTILIZATION), 1)
+    ifeq ($(USING_DVFS), 1)
+        $(error USING_GPU_UTILIZATION conflict with USING_DVFS you can read the Integration Guide to choose which one do you need)
+    endif
+endif
+
+ifeq ($(USING_UMP),1)
+export CONFIG_MALI400_UMP=y
+export EXTRA_DEFINES += -DCONFIG_MALI400_UMP=1
+ifeq ($(USE_UMPV2),1)
+UMP_SYMVERS_FILE ?= ../umpv2/Module.symvers
+else
+UMP_SYMVERS_FILE ?= ../ump/Module.symvers
+endif
+KBUILD_EXTRA_SYMBOLS = $(realpath $(UMP_SYMVERS_FILE))
+$(warning $(KBUILD_EXTRA_SYMBOLS))
+endif
+
+# Define host system directory
+KDIR-$(shell uname -m):=/lib/modules/$(shell uname -r)/build
+
+ifeq ($(O),)
+	-include $(KDIR)/.config
+else
+	-include $(O)/.config
+endif
+
+ifeq ($(ARCH), arm)
+# when compiling for ARM we're cross compiling
+export CROSS_COMPILE ?= $(call check_cc2, arm-linux-gnueabi-gcc, arm-linux-gnueabi-, arm-none-linux-gnueabi-)
+endif
+
+# report detected/selected settings
+ifdef ARM_INTERNAL_BUILD
+$(warning TARGET_PLATFORM $(TARGET_PLATFORM))
+$(warning KDIR $(KDIR))
+$(warning MALI_PLATFORM $(MALI_PLATFORM))
+endif
+
+# Set up build config
+export CONFIG_MALI400=m
+export CONFIG_MALI450=y
+export CONFIG_MALI470=y
+
+export EXTRA_DEFINES += -DCONFIG_MALI400=1
+export EXTRA_DEFINES += -DCONFIG_MALI450=1
+export EXTRA_DEFINES += -DCONFIG_MALI470=1
+
+ifneq ($(MALI_PLATFORM),)
+export EXTRA_DEFINES += -DMALI_FAKE_PLATFORM_DEVICE=1
+export MALI_PLATFORM_FILES = $(wildcard platform/$(MALI_PLATFORM)/*.c)
+endif
+
+ifeq ($(USING_PROFILING),1)
+ifeq ($(CONFIG_TRACEPOINTS),)
+$(warning CONFIG_TRACEPOINTS required for profiling)
+else
+export CONFIG_MALI400_PROFILING=y
+export EXTRA_DEFINES += -DCONFIG_MALI400_PROFILING=1
+ifeq ($(USING_INTERNAL_PROFILING),1)
+export CONFIG_MALI400_INTERNAL_PROFILING=y
+export EXTRA_DEFINES += -DCONFIG_MALI400_INTERNAL_PROFILING=1
+endif
+ifeq ($(MALI_HEATMAPS_ENABLED),1)
+export MALI_HEATMAPS_ENABLED=y
+export EXTRA_DEFINES += -DCONFIG_MALI400_HEATMAPS_ENABLED
+endif
+endif
+endif
+
+ifeq ($(MALI_DMA_BUF_MAP_ON_ATTACH),1)
+export CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH=y
+export EXTRA_DEFINES += -DCONFIG_MALI_DMA_BUF_MAP_ON_ATTACH
+endif
+
+ifeq ($(MALI_DMA_BUF_LAZY_MAP),1)
+ifeq ($(MALI_DMA_BUF_MAP_ON_ATTACH),0)
+export CONFIG_MALI_DMA_BUF_LAZY_MAP=y
+export EXTRA_DEFINES += -DCONFIG_MALI_DMA_BUF_LAZY_MAP
+else
+$(warning "You want to enable MALI_DMA_BUF_LAZY_MAP but MALI_DMA_BUF_MAP_ON_ATTACH was enabled.")
+endif
+endif
+
+ifeq ($(MALI_SHARED_INTERRUPTS),1)
+export CONFIG_MALI_SHARED_INTERRUPTS=y
+export EXTRA_DEFINES += -DCONFIG_MALI_SHARED_INTERRUPTS
+endif
+
+ifeq ($(USING_DVFS),1)
+export CONFIG_MALI_DVFS=y
+export EXTRA_DEFINES += -DCONFIG_MALI_DVFS
+endif
+
+ifeq ($(USING_DMA_BUF_FENCE),1)
+export CONFIG_MALI_DMA_BUF_FENCE=y
+export EXTRA_DEFINES += -DCONFIG_MALI_DMA_BUF_FENCE
+endif
+
+ifeq ($(MALI_PMU_PARALLEL_POWER_UP),1)
+export CONFIG_MALI_PMU_PARALLEL_POWER_UP=y
+export EXTRA_DEFINES += -DCONFIG_MALI_PMU_PARALLEL_POWER_UP
+endif
+
+ifdef CONFIG_OF
+ifeq ($(USING_DT),1)
+export CONFIG_MALI_DT=y
+export EXTRA_DEFINES += -DCONFIG_MALI_DT
+endif
+endif
+
+ifeq ($(USING_DEVFREQ), 1)
+ifdef CONFIG_PM_DEVFREQ
+export CONFIG_MALI_DEVFREQ=y
+export EXTRA_DEFINES += -DCONFIG_MALI_DEVFREQ=1
+else
+$(warning "You want to support DEVFREQ but kernel didn't support DEVFREQ.")
+endif
+endif
+
+ifneq ($(BUILD),release)
+# Debug
+export CONFIG_MALI400_DEBUG=y
+else
+# Release
+ifeq ($(MALI_QUIET),1)
+export CONFIG_MALI_QUIET=y
+export EXTRA_DEFINES += -DCONFIG_MALI_QUIET
+endif
+endif
+
+ifeq ($(MALI_SKIP_JOBS),1)
+EXTRA_DEFINES += -DPROFILING_SKIP_PP_JOBS=1 -DPROFILING_SKIP_GP_JOBS=1
+endif
+
+ifeq ($(MALI_MEM_SWAP_TRACKING),1)
+EXTRA_DEFINES += -DMALI_MEM_SWAP_TRACKING=1
+endif
+
+all: $(UMP_SYMVERS_FILE)
+	$(MAKE) ARCH=$(ARCH) -C $(KDIR) M=$(CURDIR) O=$(O) modules
+	@rm $(FILES_PREFIX)__malidrv_build_info.c $(FILES_PREFIX)__malidrv_build_info.o
+
+modules_install:
+	$(MAKE) ARCH=$(ARCH) -C $(KDIR) M=$(CURDIR) modules_install
+
+clean:
+	$(MAKE) ARCH=$(ARCH) -C $(KDIR) M=$(CURDIR) clean
+
+kernelrelease:
+	$(MAKE) ARCH=$(ARCH) -C $(KDIR) kernelrelease
+
+export CONFIG KBUILD_EXTRA_SYMBOLS
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_broadcast.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_broadcast.c
@@ -0,0 +1,142 @@
+/*
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_broadcast.h"
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+
+#define MALI_BROADCAST_REGISTER_SIZE      0x1000
+#define MALI_BROADCAST_REG_BROADCAST_MASK    0x0
+#define MALI_BROADCAST_REG_INTERRUPT_MASK    0x4
+
+struct mali_bcast_unit {
+	struct mali_hw_core hw_core;
+	u32 current_mask;
+};
+
+struct mali_bcast_unit *mali_bcast_unit_create(const _mali_osk_resource_t *resource)
+{
+	struct mali_bcast_unit *bcast_unit = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(resource);
+	MALI_DEBUG_PRINT(2, ("Broadcast: Creating Mali Broadcast unit: %s\n",
+			     resource->description));
+
+	bcast_unit = _mali_osk_malloc(sizeof(struct mali_bcast_unit));
+	if (NULL == bcast_unit) {
+		MALI_PRINT_ERROR(("Broadcast: Failed to allocate memory for Broadcast unit\n"));
+		return NULL;
+	}
+
+	if (_MALI_OSK_ERR_OK == mali_hw_core_create(&bcast_unit->hw_core,
+			resource, MALI_BROADCAST_REGISTER_SIZE)) {
+		bcast_unit->current_mask = 0;
+		mali_bcast_reset(bcast_unit);
+
+		return bcast_unit;
+	} else {
+		MALI_PRINT_ERROR(("Broadcast: Failed map broadcast unit\n"));
+	}
+
+	_mali_osk_free(bcast_unit);
+
+	return NULL;
+}
+
+void mali_bcast_unit_delete(struct mali_bcast_unit *bcast_unit)
+{
+	MALI_DEBUG_ASSERT_POINTER(bcast_unit);
+	mali_hw_core_delete(&bcast_unit->hw_core);
+	_mali_osk_free(bcast_unit);
+}
+
+/* Call this function to add the @group's id into bcast mask
+ * Note: redundant calling this function with same @group
+ * doesn't make any difference as calling it once
+ */
+void mali_bcast_add_group(struct mali_bcast_unit *bcast_unit,
+			  struct mali_group *group)
+{
+	u32 bcast_id;
+	u32 broadcast_mask;
+
+	MALI_DEBUG_ASSERT_POINTER(bcast_unit);
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	bcast_id = mali_pp_core_get_bcast_id(mali_group_get_pp_core(group));
+
+	broadcast_mask = bcast_unit->current_mask;
+
+	broadcast_mask |= (bcast_id); /* add PP core to broadcast */
+	broadcast_mask |= (bcast_id << 16); /* add MMU to broadcast */
+
+	/* store mask so we can restore on reset */
+	bcast_unit->current_mask = broadcast_mask;
+}
+
+/* Call this function to remove @group's id from bcast mask
+ * Note: redundant calling this function with same @group
+ * doesn't make any difference as calling it once
+ */
+void mali_bcast_remove_group(struct mali_bcast_unit *bcast_unit,
+			     struct mali_group *group)
+{
+	u32 bcast_id;
+	u32 broadcast_mask;
+
+	MALI_DEBUG_ASSERT_POINTER(bcast_unit);
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	bcast_id = mali_pp_core_get_bcast_id(mali_group_get_pp_core(group));
+
+	broadcast_mask = bcast_unit->current_mask;
+
+	broadcast_mask &= ~((bcast_id << 16) | bcast_id);
+
+	/* store mask so we can restore on reset */
+	bcast_unit->current_mask = broadcast_mask;
+}
+
+void mali_bcast_reset(struct mali_bcast_unit *bcast_unit)
+{
+	MALI_DEBUG_ASSERT_POINTER(bcast_unit);
+
+	MALI_DEBUG_PRINT(4,
+			 ("Broadcast: setting mask 0x%08X + 0x%08X (reset)\n",
+			  bcast_unit->current_mask,
+			  bcast_unit->current_mask & 0xFF));
+
+	/* set broadcast mask */
+	mali_hw_core_register_write(&bcast_unit->hw_core,
+				    MALI_BROADCAST_REG_BROADCAST_MASK,
+				    bcast_unit->current_mask);
+
+	/* set IRQ override mask */
+	mali_hw_core_register_write(&bcast_unit->hw_core,
+				    MALI_BROADCAST_REG_INTERRUPT_MASK,
+				    bcast_unit->current_mask & 0xFF);
+}
+
+void mali_bcast_disable(struct mali_bcast_unit *bcast_unit)
+{
+	MALI_DEBUG_ASSERT_POINTER(bcast_unit);
+
+	MALI_DEBUG_PRINT(4, ("Broadcast: setting mask 0x0 + 0x0 (disable)\n"));
+
+	/* set broadcast mask */
+	mali_hw_core_register_write(&bcast_unit->hw_core,
+				    MALI_BROADCAST_REG_BROADCAST_MASK,
+				    0x0);
+
+	/* set IRQ override mask */
+	mali_hw_core_register_write(&bcast_unit->hw_core,
+				    MALI_BROADCAST_REG_INTERRUPT_MASK,
+				    0x0);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_broadcast.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_broadcast.h
@@ -0,0 +1,57 @@
+/*
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_BROADCAST_H__
+#define __MALI_BROADCAST_H__
+
+/*
+ *  Interface for the broadcast unit on Mali-450.
+ *
+ * - Represents up to 8 × (MMU + PP) pairs.
+ * - Supports dynamically changing which (MMU + PP) pairs receive the broadcast by
+ *   setting a mask.
+ */
+
+#include "mali_hw_core.h"
+#include "mali_group.h"
+
+struct mali_bcast_unit;
+
+struct mali_bcast_unit *mali_bcast_unit_create(const _mali_osk_resource_t *resource);
+void mali_bcast_unit_delete(struct mali_bcast_unit *bcast_unit);
+
+/* Add a group to the list of (MMU + PP) pairs broadcasts go out to. */
+void mali_bcast_add_group(struct mali_bcast_unit *bcast_unit, struct mali_group *group);
+
+/* Remove a group to the list of (MMU + PP) pairs broadcasts go out to. */
+void mali_bcast_remove_group(struct mali_bcast_unit *bcast_unit, struct mali_group *group);
+
+/* Re-set cached mask. This needs to be called after having been suspended. */
+void mali_bcast_reset(struct mali_bcast_unit *bcast_unit);
+
+/**
+ * Disable broadcast unit
+ *
+ * mali_bcast_enable must be called to re-enable the unit. Cores may not be
+ * added or removed when the unit is disabled.
+ */
+void mali_bcast_disable(struct mali_bcast_unit *bcast_unit);
+
+/**
+ * Re-enable broadcast unit
+ *
+ * This resets the masks to include the cores present when mali_bcast_disable was called.
+ */
+MALI_STATIC_INLINE void mali_bcast_enable(struct mali_bcast_unit *bcast_unit)
+{
+	mali_bcast_reset(bcast_unit);
+}
+
+#endif /* __MALI_BROADCAST_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_control_timer.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_control_timer.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) 2010-2012, 2014-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_utilization.h"
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_dvfs_policy.h"
+#include "mali_control_timer.h"
+
+static u64 period_start_time = 0;
+
+static _mali_osk_timer_t *mali_control_timer = NULL;
+static mali_bool timer_running = MALI_FALSE;
+
+static u32 mali_control_timeout = 1000;
+
+void mali_control_timer_add(u32 timeout)
+{
+	_mali_osk_timer_add(mali_control_timer, _mali_osk_time_mstoticks(timeout));
+}
+
+static void mali_control_timer_callback(void *arg)
+{
+	if (mali_utilization_enabled()) {
+		struct mali_gpu_utilization_data *util_data = NULL;
+		u64 time_period = 0;
+		mali_bool need_add_timer = MALI_TRUE;
+
+		/* Calculate gpu utilization */
+		util_data = mali_utilization_calculate(&period_start_time, &time_period, &need_add_timer);
+
+		if (util_data) {
+#if defined(CONFIG_MALI_DVFS)
+			mali_dvfs_policy_realize(util_data, time_period);
+#else
+			mali_utilization_platform_realize(util_data);
+#endif
+
+			if (MALI_TRUE == need_add_timer) {
+				mali_control_timer_add(mali_control_timeout);
+			}
+		}
+	}
+}
+
+/* Init a timer (for now it is used for GPU utilization and dvfs) */
+_mali_osk_errcode_t mali_control_timer_init(void)
+{
+	_mali_osk_device_data data;
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+		/* Use device specific settings (if defined) */
+		if (0 != data.control_interval) {
+			mali_control_timeout = data.control_interval;
+			MALI_DEBUG_PRINT(2, ("Mali GPU Timer: %u\n", mali_control_timeout));
+		}
+	}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+	mali_control_timer = _mali_osk_timer_init(mali_control_timer_callback);
+#else
+	mali_control_timer = _mali_osk_timer_init();
+#endif
+	if (NULL == mali_control_timer) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 14, 0)
+	_mali_osk_timer_setcallback(mali_control_timer, mali_control_timer_callback, NULL);
+#endif
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_control_timer_term(void)
+{
+	if (NULL != mali_control_timer) {
+		_mali_osk_timer_del(mali_control_timer);
+		timer_running = MALI_FALSE;
+		_mali_osk_timer_term(mali_control_timer);
+		mali_control_timer = NULL;
+	}
+}
+
+mali_bool mali_control_timer_resume(u64 time_now)
+{
+	mali_utilization_data_assert_locked();
+
+	if (timer_running != MALI_TRUE) {
+		timer_running = MALI_TRUE;
+
+		period_start_time = time_now;
+
+		mali_utilization_reset();
+
+		return MALI_TRUE;
+	}
+
+	return MALI_FALSE;
+}
+
+void mali_control_timer_pause(void)
+{
+	mali_utilization_data_assert_locked();
+	if (timer_running == MALI_TRUE) {
+		timer_running = MALI_FALSE;
+	}
+}
+
+void mali_control_timer_suspend(mali_bool suspend)
+{
+	mali_utilization_data_lock();
+
+	if (timer_running == MALI_TRUE) {
+		timer_running = MALI_FALSE;
+
+		mali_utilization_data_unlock();
+
+		if (suspend == MALI_TRUE) {
+			_mali_osk_timer_del(mali_control_timer);
+			mali_utilization_reset();
+		}
+	} else {
+		mali_utilization_data_unlock();
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_control_timer.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_control_timer.h
@@ -0,0 +1,28 @@
+/*
+ * Copyright (C) 2010-2012, 2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_CONTROL_TIMER_H__
+#define __MALI_CONTROL_TIMER_H__
+
+#include "mali_osk.h"
+
+_mali_osk_errcode_t mali_control_timer_init(void);
+
+void mali_control_timer_term(void);
+
+mali_bool mali_control_timer_resume(u64 time_now);
+
+void mali_control_timer_suspend(mali_bool suspend);
+void mali_control_timer_pause(void);
+
+void mali_control_timer_add(u32 timeout);
+
+#endif /* __MALI_CONTROL_TIMER_H__ */
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_dlbu.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_dlbu.c
@@ -0,0 +1,213 @@
+/*
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_dlbu.h"
+#include "mali_memory.h"
+#include "mali_pp.h"
+#include "mali_group.h"
+#include "mali_osk.h"
+#include "mali_hw_core.h"
+
+/**
+ * Size of DLBU registers in bytes
+ */
+#define MALI_DLBU_SIZE 0x400
+
+mali_dma_addr mali_dlbu_phys_addr = 0;
+static mali_io_address mali_dlbu_cpu_addr = NULL;
+
+/**
+ * DLBU register numbers
+ * Used in the register read/write routines.
+ * See the hardware documentation for more information about each register
+ */
+typedef enum mali_dlbu_register {
+	MALI_DLBU_REGISTER_MASTER_TLLIST_PHYS_ADDR = 0x0000, /**< Master tile list physical base address;
+                                                             31:12 Physical address to the page used for the DLBU
+                                                             0 DLBU enable - set this bit to 1 enables the AXI bus
+                                                             between PPs and L2s, setting to 0 disables the router and
+                                                             no further transactions are sent to DLBU */
+	MALI_DLBU_REGISTER_MASTER_TLLIST_VADDR     = 0x0004, /**< Master tile list virtual base address;
+                                                             31:12 Virtual address to the page used for the DLBU */
+	MALI_DLBU_REGISTER_TLLIST_VBASEADDR     = 0x0008, /**< Tile list virtual base address;
+                                                             31:12 Virtual address to the tile list. This address is used when
+                                                             calculating the call address sent to PP.*/
+	MALI_DLBU_REGISTER_FB_DIM                 = 0x000C, /**< Framebuffer dimension;
+                                                             23:16 Number of tiles in Y direction-1
+                                                             7:0 Number of tiles in X direction-1 */
+	MALI_DLBU_REGISTER_TLLIST_CONF       = 0x0010, /**< Tile list configuration;
+                                                             29:28 select the size of each allocated block: 0=128 bytes, 1=256, 2=512, 3=1024
+                                                             21:16 2^n number of tiles to be binned to one tile list in Y direction
+                                                             5:0 2^n number of tiles to be binned to one tile list in X direction */
+	MALI_DLBU_REGISTER_START_TILE_POS         = 0x0014, /**< Start tile positions;
+                                                             31:24 start position in Y direction for group 1
+                                                             23:16 start position in X direction for group 1
+                                                             15:8 start position in Y direction for group 0
+                                                             7:0 start position in X direction for group 0 */
+	MALI_DLBU_REGISTER_PP_ENABLE_MASK         = 0x0018, /**< PP enable mask;
+                                                             7 enable PP7 for load balancing
+                                                             6 enable PP6 for load balancing
+                                                             5 enable PP5 for load balancing
+                                                             4 enable PP4 for load balancing
+                                                             3 enable PP3 for load balancing
+                                                             2 enable PP2 for load balancing
+                                                             1 enable PP1 for load balancing
+                                                             0 enable PP0 for load balancing */
+} mali_dlbu_register;
+
+typedef enum {
+	PP0ENABLE = 0,
+	PP1ENABLE,
+	PP2ENABLE,
+	PP3ENABLE,
+	PP4ENABLE,
+	PP5ENABLE,
+	PP6ENABLE,
+	PP7ENABLE
+} mali_dlbu_pp_enable;
+
+struct mali_dlbu_core {
+	struct mali_hw_core     hw_core;           /**< Common for all HW cores */
+	u32                     pp_cores_mask;     /**< This is a mask for the PP cores whose operation will be controlled by LBU
+                                                      see MALI_DLBU_REGISTER_PP_ENABLE_MASK register */
+};
+
+_mali_osk_errcode_t mali_dlbu_initialize(void)
+{
+	MALI_DEBUG_PRINT(2, ("Mali DLBU: Initializing\n"));
+
+	if (_MALI_OSK_ERR_OK ==
+	    mali_mmu_get_table_page(&mali_dlbu_phys_addr,
+				    &mali_dlbu_cpu_addr)) {
+		return _MALI_OSK_ERR_OK;
+	}
+
+	return _MALI_OSK_ERR_FAULT;
+}
+
+void mali_dlbu_terminate(void)
+{
+	MALI_DEBUG_PRINT(3, ("Mali DLBU: terminating\n"));
+
+	if (0 != mali_dlbu_phys_addr && 0 != mali_dlbu_cpu_addr) {
+		mali_mmu_release_table_page(mali_dlbu_phys_addr,
+					    mali_dlbu_cpu_addr);
+		mali_dlbu_phys_addr = 0;
+		mali_dlbu_cpu_addr = 0;
+	}
+}
+
+struct mali_dlbu_core *mali_dlbu_create(const _mali_osk_resource_t *resource)
+{
+	struct mali_dlbu_core *core = NULL;
+
+	MALI_DEBUG_PRINT(2, ("Mali DLBU: Creating Mali dynamic load balancing unit: %s\n", resource->description));
+
+	core = _mali_osk_malloc(sizeof(struct mali_dlbu_core));
+	if (NULL != core) {
+		if (_MALI_OSK_ERR_OK == mali_hw_core_create(&core->hw_core, resource, MALI_DLBU_SIZE)) {
+			core->pp_cores_mask = 0;
+			if (_MALI_OSK_ERR_OK == mali_dlbu_reset(core)) {
+				return core;
+			}
+			MALI_PRINT_ERROR(("Failed to reset DLBU %s\n", core->hw_core.description));
+			mali_hw_core_delete(&core->hw_core);
+		}
+
+		_mali_osk_free(core);
+	} else {
+		MALI_PRINT_ERROR(("Mali DLBU: Failed to allocate memory for DLBU core\n"));
+	}
+
+	return NULL;
+}
+
+void mali_dlbu_delete(struct mali_dlbu_core *dlbu)
+{
+	MALI_DEBUG_ASSERT_POINTER(dlbu);
+	mali_hw_core_delete(&dlbu->hw_core);
+	_mali_osk_free(dlbu);
+}
+
+_mali_osk_errcode_t mali_dlbu_reset(struct mali_dlbu_core *dlbu)
+{
+	u32 dlbu_registers[7];
+	_mali_osk_errcode_t err = _MALI_OSK_ERR_FAULT;
+	MALI_DEBUG_ASSERT_POINTER(dlbu);
+
+	MALI_DEBUG_PRINT(4, ("Mali DLBU: mali_dlbu_reset: %s\n", dlbu->hw_core.description));
+
+	dlbu_registers[0] = mali_dlbu_phys_addr | 1; /* bit 0 enables the whole core */
+	dlbu_registers[1] = MALI_DLBU_VIRT_ADDR;
+	dlbu_registers[2] = 0;
+	dlbu_registers[3] = 0;
+	dlbu_registers[4] = 0;
+	dlbu_registers[5] = 0;
+	dlbu_registers[6] = dlbu->pp_cores_mask;
+
+	/* write reset values to core registers */
+	mali_hw_core_register_write_array_relaxed(&dlbu->hw_core, MALI_DLBU_REGISTER_MASTER_TLLIST_PHYS_ADDR, dlbu_registers, 7);
+
+	err = _MALI_OSK_ERR_OK;
+
+	return err;
+}
+
+void mali_dlbu_update_mask(struct mali_dlbu_core *dlbu)
+{
+	MALI_DEBUG_ASSERT_POINTER(dlbu);
+
+	mali_hw_core_register_write(&dlbu->hw_core, MALI_DLBU_REGISTER_PP_ENABLE_MASK, dlbu->pp_cores_mask);
+}
+
+void mali_dlbu_add_group(struct mali_dlbu_core *dlbu, struct mali_group *group)
+{
+	struct mali_pp_core *pp_core;
+	u32 bcast_id;
+
+	MALI_DEBUG_ASSERT_POINTER(dlbu);
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	pp_core = mali_group_get_pp_core(group);
+	bcast_id = mali_pp_core_get_bcast_id(pp_core);
+
+	dlbu->pp_cores_mask |= bcast_id;
+	MALI_DEBUG_PRINT(3, ("Mali DLBU: Adding core[%d] New mask= 0x%02x\n", bcast_id , dlbu->pp_cores_mask));
+}
+
+/* Remove a group from the DLBU */
+void mali_dlbu_remove_group(struct mali_dlbu_core *dlbu, struct mali_group *group)
+{
+	struct mali_pp_core *pp_core;
+	u32 bcast_id;
+
+	MALI_DEBUG_ASSERT_POINTER(dlbu);
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	pp_core = mali_group_get_pp_core(group);
+	bcast_id = mali_pp_core_get_bcast_id(pp_core);
+
+	dlbu->pp_cores_mask &= ~bcast_id;
+	MALI_DEBUG_PRINT(3, ("Mali DLBU: Removing core[%d] New mask= 0x%02x\n", bcast_id, dlbu->pp_cores_mask));
+}
+
+/* Configure the DLBU for \a job. This needs to be done before the job is started on the groups in the DLBU. */
+void mali_dlbu_config_job(struct mali_dlbu_core *dlbu, struct mali_pp_job *job)
+{
+	u32 *registers;
+	MALI_DEBUG_ASSERT(job);
+	registers = mali_pp_job_get_dlbu_registers(job);
+	MALI_DEBUG_PRINT(4, ("Mali DLBU: Starting job\n"));
+
+	/* Writing 4 registers:
+	 * DLBU registers except the first two (written once at DLBU initialisation / reset) and the PP_ENABLE_MASK register */
+	mali_hw_core_register_write_array_relaxed(&dlbu->hw_core, MALI_DLBU_REGISTER_TLLIST_VBASEADDR, registers, 4);
+
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_dlbu.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_dlbu.h
@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_DLBU_H__
+#define __MALI_DLBU_H__
+
+#define MALI_DLBU_VIRT_ADDR 0xFFF00000 /* master tile virtual address fixed at this value and mapped into every session */
+
+#include "mali_osk.h"
+
+struct mali_pp_job;
+struct mali_group;
+struct mali_dlbu_core;
+
+extern mali_dma_addr mali_dlbu_phys_addr;
+
+_mali_osk_errcode_t mali_dlbu_initialize(void);
+void mali_dlbu_terminate(void);
+
+struct mali_dlbu_core *mali_dlbu_create(const _mali_osk_resource_t *resource);
+void mali_dlbu_delete(struct mali_dlbu_core *dlbu);
+
+_mali_osk_errcode_t mali_dlbu_reset(struct mali_dlbu_core *dlbu);
+
+void mali_dlbu_add_group(struct mali_dlbu_core *dlbu, struct mali_group *group);
+void mali_dlbu_remove_group(struct mali_dlbu_core *dlbu, struct mali_group *group);
+
+/** @brief Called to update HW after DLBU state changed
+ *
+ * This function must be called after \a mali_dlbu_add_group or \a
+ * mali_dlbu_remove_group to write the updated mask to hardware, unless the
+ * same is accomplished by calling \a mali_dlbu_reset.
+ */
+void mali_dlbu_update_mask(struct mali_dlbu_core *dlbu);
+
+void mali_dlbu_config_job(struct mali_dlbu_core *dlbu, struct mali_pp_job *job);
+
+#endif /* __MALI_DLBU_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_dvfs_policy.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_dvfs_policy.c
@@ -0,0 +1,308 @@
+/*
+ * Copyright (C) 2010-2012, 2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/mali/mali_utgard.h>
+#include "mali_kernel_common.h"
+#include "mali_scheduler.h"
+#include "mali_dvfs_policy.h"
+#include "mali_osk_mali.h"
+#include "mali_osk_profiling.h"
+
+#define CLOCK_TUNING_TIME_DEBUG 0
+
+#define MAX_PERFORMANCE_VALUE 256
+#define MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(percent) ((int) ((percent)*(MAX_PERFORMANCE_VALUE)/100.0 + 0.5))
+
+/** The max fps the same as display vsync default 60, can set by module insert parameter */
+int mali_max_system_fps = 60;
+/** A lower limit on their desired FPS default 58, can set by module insert parameter */
+int mali_desired_fps = 58;
+
+static int mali_fps_step1 = 0;
+static int mali_fps_step2 = 0;
+
+static int clock_step = -1;
+static int cur_clk_step = -1;
+static struct mali_gpu_clock *gpu_clk = NULL;
+
+/*Function prototype */
+static int (*mali_gpu_set_freq)(int) = NULL;
+static int (*mali_gpu_get_freq)(void) = NULL;
+
+static mali_bool mali_dvfs_enabled = MALI_FALSE;
+
+#define NUMBER_OF_NANOSECONDS_PER_SECOND  1000000000ULL
+static u32 calculate_window_render_fps(u64 time_period)
+{
+	u32 max_window_number;
+	u64 tmp;
+	u64 max = time_period;
+	u32 leading_zeroes;
+	u32 shift_val;
+	u32 time_period_shift;
+	u32 max_window_number_shift;
+	u32 ret_val;
+
+	max_window_number = mali_session_max_window_num();
+
+	/* To avoid float division, extend the dividend to ns unit */
+	tmp = (u64)max_window_number * NUMBER_OF_NANOSECONDS_PER_SECOND;
+	if (tmp > time_period) {
+		max = tmp;
+	}
+
+	/*
+	 * We may have 64-bit values, a dividend or a divisor or both
+	 * To avoid dependencies to a 64-bit divider, we shift down the two values
+	 * equally first.
+	 */
+	leading_zeroes = _mali_osk_clz((u32)(max >> 32));
+	shift_val = 32 - leading_zeroes;
+
+	time_period_shift = (u32)(time_period >> shift_val);
+	max_window_number_shift = (u32)(tmp >> shift_val);
+
+	ret_val = max_window_number_shift / time_period_shift;
+
+	return ret_val;
+}
+
+static bool mali_pickup_closest_avail_clock(int target_clock_mhz, mali_bool pick_clock_up)
+{
+	int i = 0;
+	bool clock_changed = false;
+
+	/* Round up the closest available frequency step for target_clock_hz */
+	for (i = 0; i < gpu_clk->num_of_steps; i++) {
+		/* Find the first item > target_clock_hz */
+		if (((int)(gpu_clk->item[i].clock) - target_clock_mhz) > 0) {
+			break;
+		}
+	}
+
+	/* If the target clock greater than the maximum clock just pick the maximum one*/
+	if (i == gpu_clk->num_of_steps) {
+		i = gpu_clk->num_of_steps - 1;
+	} else {
+		if ((!pick_clock_up) && (i > 0)) {
+			i = i - 1;
+		}
+	}
+
+	clock_step = i;
+	if (cur_clk_step != clock_step) {
+		clock_changed = true;
+	}
+
+	return clock_changed;
+}
+
+void mali_dvfs_policy_realize(struct mali_gpu_utilization_data *data, u64 time_period)
+{
+	int under_perform_boundary_value = 0;
+	int over_perform_boundary_value = 0;
+	int current_fps = 0;
+	int current_gpu_util = 0;
+	bool clock_changed = false;
+#if CLOCK_TUNING_TIME_DEBUG
+	struct timeval start;
+	struct timeval stop;
+	unsigned int elapse_time;
+	do_gettimeofday(&start);
+#endif
+	u32 window_render_fps;
+
+	if (NULL == gpu_clk) {
+		MALI_DEBUG_PRINT(2, ("Enable DVFS but patform doesn't Support freq change. \n"));
+		return;
+	}
+
+	window_render_fps = calculate_window_render_fps(time_period);
+
+	current_fps = window_render_fps;
+	current_gpu_util = data->utilization_gpu;
+
+	/* Get the specific under_perform_boundary_value and over_perform_boundary_value */
+	if ((mali_desired_fps <= current_fps) && (current_fps < mali_max_system_fps)) {
+		under_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(90);
+		over_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(70);
+	} else if ((mali_fps_step1 <= current_fps) && (current_fps < mali_desired_fps)) {
+		under_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(55);
+		over_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(35);
+	} else if ((mali_fps_step2 <= current_fps) && (current_fps < mali_fps_step1)) {
+		under_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(70);
+		over_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(50);
+	} else {
+		under_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(55);
+		over_perform_boundary_value = MALI_PERCENTAGE_TO_UTILIZATION_FRACTION(35);
+	}
+
+	MALI_DEBUG_PRINT(5, ("Using ARM power policy: gpu util = %d \n", current_gpu_util));
+	MALI_DEBUG_PRINT(5, ("Using ARM power policy: under_perform = %d,  over_perform = %d \n", under_perform_boundary_value, over_perform_boundary_value));
+	MALI_DEBUG_PRINT(5, ("Using ARM power policy: render fps = %d,  pressure render fps = %d \n", current_fps, window_render_fps));
+
+	/* Get current clock value */
+	cur_clk_step = mali_gpu_get_freq();
+
+	/* Consider offscreen */
+	if (0 == current_fps) {
+		/* GP or PP under perform, need to give full power */
+		if (current_gpu_util > over_perform_boundary_value) {
+			if (cur_clk_step != gpu_clk->num_of_steps - 1) {
+				clock_changed = true;
+				clock_step = gpu_clk->num_of_steps - 1;
+			}
+		}
+
+		/* If GPU is idle, use lowest power */
+		if (0 == current_gpu_util) {
+			if (cur_clk_step != 0) {
+				clock_changed = true;
+				clock_step = 0;
+			}
+		}
+
+		goto real_setting;
+	}
+
+	/* 2. Calculate target clock if the GPU clock can be tuned */
+	if (-1 != cur_clk_step) {
+		int target_clk_mhz = -1;
+		mali_bool pick_clock_up = MALI_TRUE;
+
+		if (current_gpu_util > under_perform_boundary_value) {
+			/* when under perform, need to consider the fps part */
+			target_clk_mhz = gpu_clk->item[cur_clk_step].clock * current_gpu_util * mali_desired_fps / under_perform_boundary_value / current_fps;
+			pick_clock_up = MALI_TRUE;
+		} else if (current_gpu_util < over_perform_boundary_value) {
+			/* when over perform, did't need to consider fps, system didn't want to reach desired fps */
+			target_clk_mhz = gpu_clk->item[cur_clk_step].clock * current_gpu_util / under_perform_boundary_value;
+			pick_clock_up = MALI_FALSE;
+		}
+
+		if (-1 != target_clk_mhz) {
+			clock_changed = mali_pickup_closest_avail_clock(target_clk_mhz, pick_clock_up);
+		}
+	}
+
+real_setting:
+	if (clock_changed) {
+		mali_gpu_set_freq(clock_step);
+
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+					      MALI_PROFILING_EVENT_CHANNEL_GPU |
+					      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+					      gpu_clk->item[clock_step].clock,
+					      gpu_clk->item[clock_step].vol / 1000,
+					      0, 0, 0);
+	}
+
+#if CLOCK_TUNING_TIME_DEBUG
+	do_gettimeofday(&stop);
+
+	elapse_time = timeval_to_ns(&stop) - timeval_to_ns(&start);
+	MALI_DEBUG_PRINT(2, ("Using ARM power policy:  eclapse time = %d\n", elapse_time));
+#endif
+}
+
+_mali_osk_errcode_t mali_dvfs_policy_init(void)
+{
+	_mali_osk_device_data data;
+	_mali_osk_errcode_t err = _MALI_OSK_ERR_OK;
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+		if ((NULL != data.get_clock_info) && (NULL != data.set_freq) && (NULL != data.get_freq)) {
+			MALI_DEBUG_PRINT(2, ("Mali DVFS init: using arm dvfs policy \n"));
+
+
+			mali_fps_step1 = mali_max_system_fps / 3;
+			mali_fps_step2 = mali_max_system_fps / 5;
+
+			data.get_clock_info(&gpu_clk);
+
+			if (gpu_clk != NULL) {
+#ifdef DEBUG
+				int i;
+				for (i = 0; i < gpu_clk->num_of_steps; i++) {
+					MALI_DEBUG_PRINT(5, ("mali gpu clock info: step%d clock(%d)Hz,vol(%d) \n",
+							     i, gpu_clk->item[i].clock, gpu_clk->item[i].vol));
+				}
+#endif
+			} else {
+				MALI_DEBUG_PRINT(2, ("Mali DVFS init: platform didn't define enough info for ddk to do DVFS \n"));
+			}
+
+			mali_gpu_get_freq = data.get_freq;
+			mali_gpu_set_freq = data.set_freq;
+
+			if ((NULL != gpu_clk) && (gpu_clk->num_of_steps > 0)
+			    && (NULL != mali_gpu_get_freq) && (NULL != mali_gpu_set_freq)) {
+				mali_dvfs_enabled = MALI_TRUE;
+			}
+		} else {
+			MALI_DEBUG_PRINT(2, ("Mali DVFS init: platform function callback incomplete, need check mali_gpu_device_data in platform .\n"));
+		}
+	} else {
+		err = _MALI_OSK_ERR_FAULT;
+		MALI_DEBUG_PRINT(2, ("Mali DVFS init: get platform data error .\n"));
+	}
+
+	return err;
+}
+
+/*
+ * Always give full power when start a new period,
+ * if mali dvfs enabled, for performance consideration
+ */
+void mali_dvfs_policy_new_period(void)
+{
+	/* Always give full power when start a new period */
+	unsigned int cur_clk_step = 0;
+
+	cur_clk_step = mali_gpu_get_freq();
+
+	if (cur_clk_step != (gpu_clk->num_of_steps - 1)) {
+		mali_gpu_set_freq(gpu_clk->num_of_steps - 1);
+
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+					      MALI_PROFILING_EVENT_CHANNEL_GPU |
+					      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE, gpu_clk->item[gpu_clk->num_of_steps - 1].clock,
+					      gpu_clk->item[gpu_clk->num_of_steps - 1].vol / 1000, 0, 0, 0);
+	}
+}
+
+mali_bool mali_dvfs_policy_enabled(void)
+{
+	return mali_dvfs_enabled;
+}
+
+#if defined(CONFIG_MALI400_PROFILING)
+void mali_get_current_gpu_clk_item(struct mali_gpu_clk_item *clk_item)
+{
+	if (mali_platform_device != NULL) {
+
+		struct mali_gpu_device_data *device_data = NULL;
+		device_data = (struct mali_gpu_device_data *)mali_platform_device->dev.platform_data;
+
+		if ((NULL != device_data->get_clock_info) && (NULL != device_data->get_freq)) {
+
+			int cur_clk_step = device_data->get_freq();
+			struct mali_gpu_clock *mali_gpu_clk = NULL;
+
+			device_data->get_clock_info(&mali_gpu_clk);
+			clk_item->clock = mali_gpu_clk->item[cur_clk_step].clock;
+			clk_item->vol = mali_gpu_clk->item[cur_clk_step].vol;
+		} else {
+			MALI_DEBUG_PRINT(2, ("Mali GPU Utilization: platform function callback incomplete, need check mali_gpu_device_data in platform .\n"));
+		}
+	}
+}
+#endif
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_dvfs_policy.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_dvfs_policy.h
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) 2010-2012, 2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_DVFS_POLICY_H__
+#define __MALI_DVFS_POLICY_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+void mali_dvfs_policy_realize(struct mali_gpu_utilization_data *data, u64 time_period);
+
+_mali_osk_errcode_t mali_dvfs_policy_init(void);
+
+void mali_dvfs_policy_new_period(void);
+
+mali_bool mali_dvfs_policy_enabled(void);
+
+#if defined(CONFIG_MALI400_PROFILING)
+void mali_get_current_gpu_clk_item(struct mali_gpu_clk_item *clk_item);
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif/* __MALI_DVFS_POLICY_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_executor.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_executor.c
@@ -0,0 +1,2701 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_executor.h"
+#include "mali_scheduler.h"
+#include "mali_kernel_common.h"
+#include "mali_kernel_core.h"
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_pp.h"
+#include "mali_pp_job.h"
+#include "mali_group.h"
+#include "mali_pm.h"
+#include "mali_timeline.h"
+#include "mali_osk_profiling.h"
+#include "mali_session.h"
+#include "mali_osk_mali.h"
+
+/*
+ * If dma_buf with map on demand is used, we defer job deletion and job queue
+ * if in atomic context, since both might sleep.
+ */
+#if defined(CONFIG_DMA_SHARED_BUFFER) && !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+#define MALI_EXECUTOR_USE_DEFERRED_PP_JOB_DELETE 1
+#define MALI_EXECUTOR_USE_DEFERRED_PP_JOB_QUEUE 1
+#endif /* !defined(CONFIG_DMA_SHARED_BUFFER) && !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH) */
+
+/*
+ * ---------- static type definitions (structs, enums, etc) ----------
+ */
+
+enum mali_executor_state_t {
+	EXEC_STATE_NOT_PRESENT, /* Virtual group on Mali-300/400 (do not use) */
+	EXEC_STATE_DISABLED,    /* Disabled by core scaling (do not use) */
+	EXEC_STATE_EMPTY,       /* No child groups for virtual group (do not use) */
+	EXEC_STATE_INACTIVE,    /* Can be used, but must be activate first */
+	EXEC_STATE_IDLE,        /* Active and ready to be used */
+	EXEC_STATE_WORKING,     /* Executing a job */
+};
+
+/*
+ * ---------- global variables (exported due to inline functions) ----------
+ */
+
+/* Lock for this module (protecting all HW access except L2 caches) */
+_mali_osk_spinlock_irq_t *mali_executor_lock_obj = NULL;
+
+mali_bool mali_executor_hints[MALI_EXECUTOR_HINT_MAX];
+
+/*
+ * ---------- static variables ----------
+ */
+
+/* Used to defer job scheduling */
+static _mali_osk_wq_work_t *executor_wq_high_pri = NULL;
+
+/* Store version from GP and PP (user space wants to know this) */
+static u32 pp_version = 0;
+static u32 gp_version = 0;
+
+/* List of physical PP groups which are disabled by some external source */
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(group_list_disabled);
+static u32 group_list_disabled_count = 0;
+
+/* List of groups which can be used, but activate first */
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(group_list_inactive);
+static u32 group_list_inactive_count = 0;
+
+/* List of groups which are active and ready to be used */
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(group_list_idle);
+static u32 group_list_idle_count = 0;
+
+/* List of groups which are executing a job */
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(group_list_working);
+static u32 group_list_working_count = 0;
+
+/* Virtual group (if any) */
+static struct mali_group *virtual_group = NULL;
+
+/* Virtual group state is tracked with a state variable instead of 4 lists */
+static enum mali_executor_state_t virtual_group_state = EXEC_STATE_NOT_PRESENT;
+
+/* GP group */
+static struct mali_group *gp_group = NULL;
+
+/* GP group state is tracked with a state variable instead of 4 lists */
+static enum mali_executor_state_t gp_group_state = EXEC_STATE_NOT_PRESENT;
+
+static u32 gp_returned_cookie = 0;
+
+/* Total number of physical PP cores present */
+static u32 num_physical_pp_cores_total = 0;
+
+/* Number of physical cores which are enabled */
+static u32 num_physical_pp_cores_enabled = 0;
+
+/* Enable or disable core scaling */
+static mali_bool core_scaling_enabled = MALI_TRUE;
+
+/* Variables to allow safe pausing of the scheduler */
+static _mali_osk_wait_queue_t *executor_working_wait_queue = NULL;
+static u32 pause_count = 0;
+
+/* PP cores haven't been enabled because of some pp cores haven't been disabled. */
+static int core_scaling_delay_up_mask[MALI_MAX_NUMBER_OF_DOMAINS] = { 0 };
+
+/* Variables used to implement notify pp core changes to userspace when core scaling
+ * is finished in mali_executor_complete_group() function. */
+static _mali_osk_wq_work_t *executor_wq_notify_core_change = NULL;
+static _mali_osk_wait_queue_t *executor_notify_core_change_wait_queue = NULL;
+
+/*
+ * ---------- Forward declaration of static functions ----------
+ */
+static mali_bool mali_executor_is_suspended(void *data);
+static mali_bool mali_executor_is_working(void);
+static void mali_executor_disable_empty_virtual(void);
+static mali_bool mali_executor_physical_rejoin_virtual(struct mali_group *group);
+static mali_bool mali_executor_has_virtual_group(void);
+static mali_bool mali_executor_virtual_group_is_usable(void);
+static void mali_executor_schedule(void);
+static void mali_executor_wq_schedule(void *arg);
+static void mali_executor_send_gp_oom_to_user(struct mali_gp_job *job);
+static void mali_executor_complete_group(struct mali_group *group,
+		mali_bool success,
+		struct mali_gp_job **gp_job_done,
+		struct mali_pp_job **pp_job_done);
+static void mali_executor_change_state_pp_physical(struct mali_group *group,
+		_mali_osk_list_t *old_list,
+		u32 *old_count,
+		_mali_osk_list_t *new_list,
+		u32 *new_count);
+static mali_bool mali_executor_group_is_in_state(struct mali_group *group,
+		enum mali_executor_state_t state);
+
+static void mali_executor_group_enable_internal(struct mali_group *group);
+static void mali_executor_group_disable_internal(struct mali_group *group);
+static void mali_executor_core_scale(unsigned int target_core_nr);
+static void mali_executor_core_scale_in_group_complete(struct mali_group *group);
+static void mali_executor_notify_core_change(u32 num_cores);
+static void mali_executor_wq_notify_core_change(void *arg);
+static void mali_executor_change_group_status_disabled(struct mali_group *group);
+static mali_bool mali_executor_deactivate_list_idle(mali_bool deactivate_idle_group);
+static void mali_executor_set_state_pp_physical(struct mali_group *group,
+		_mali_osk_list_t *new_list,
+		u32 *new_count);
+
+/*
+ * ---------- Actual implementation ----------
+ */
+
+_mali_osk_errcode_t mali_executor_initialize(void)
+{
+	mali_executor_lock_obj = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_ORDERED, _MALI_OSK_LOCK_ORDER_EXECUTOR);
+	if (NULL == mali_executor_lock_obj) {
+		mali_executor_terminate();
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	executor_wq_high_pri = _mali_osk_wq_create_work_high_pri(mali_executor_wq_schedule, NULL);
+	if (NULL == executor_wq_high_pri) {
+		mali_executor_terminate();
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	executor_working_wait_queue = _mali_osk_wait_queue_init();
+	if (NULL == executor_working_wait_queue) {
+		mali_executor_terminate();
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	executor_wq_notify_core_change = _mali_osk_wq_create_work(mali_executor_wq_notify_core_change, NULL);
+	if (NULL == executor_wq_notify_core_change) {
+		mali_executor_terminate();
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	executor_notify_core_change_wait_queue = _mali_osk_wait_queue_init();
+	if (NULL == executor_notify_core_change_wait_queue) {
+		mali_executor_terminate();
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_executor_terminate(void)
+{
+	if (NULL != executor_notify_core_change_wait_queue) {
+		_mali_osk_wait_queue_term(executor_notify_core_change_wait_queue);
+		executor_notify_core_change_wait_queue = NULL;
+	}
+
+	if (NULL != executor_wq_notify_core_change) {
+		_mali_osk_wq_delete_work(executor_wq_notify_core_change);
+		executor_wq_notify_core_change = NULL;
+	}
+
+	if (NULL != executor_working_wait_queue) {
+		_mali_osk_wait_queue_term(executor_working_wait_queue);
+		executor_working_wait_queue = NULL;
+	}
+
+	if (NULL != executor_wq_high_pri) {
+		_mali_osk_wq_delete_work(executor_wq_high_pri);
+		executor_wq_high_pri = NULL;
+	}
+
+	if (NULL != mali_executor_lock_obj) {
+		_mali_osk_spinlock_irq_term(mali_executor_lock_obj);
+		mali_executor_lock_obj = NULL;
+	}
+}
+
+void mali_executor_populate(void)
+{
+	u32 num_groups;
+	u32 i;
+
+	num_groups = mali_group_get_glob_num_groups();
+
+	/* Do we have a virtual group? */
+	for (i = 0; i < num_groups; i++) {
+		struct mali_group *group = mali_group_get_glob_group(i);
+
+		if (mali_group_is_virtual(group)) {
+			virtual_group = group;
+			virtual_group_state = EXEC_STATE_INACTIVE;
+			break;
+		}
+	}
+
+	/* Find all the available physical GP and PP cores */
+	for (i = 0; i < num_groups; i++) {
+		struct mali_group *group = mali_group_get_glob_group(i);
+
+		if (NULL != group) {
+			struct mali_pp_core *pp_core = mali_group_get_pp_core(group);
+			struct mali_gp_core *gp_core = mali_group_get_gp_core(group);
+
+			if (!mali_group_is_virtual(group)) {
+				if (NULL != pp_core) {
+					if (0 == pp_version) {
+						/* Retrieve PP version from the first available PP core */
+						pp_version = mali_pp_core_get_version(pp_core);
+					}
+
+					if (NULL != virtual_group) {
+						mali_executor_lock();
+						mali_group_add_group(virtual_group, group);
+						mali_executor_unlock();
+					} else {
+						_mali_osk_list_add(&group->executor_list, &group_list_inactive);
+						group_list_inactive_count++;
+					}
+
+					num_physical_pp_cores_total++;
+				} else {
+					MALI_DEBUG_ASSERT_POINTER(gp_core);
+
+					if (0 == gp_version) {
+						/* Retrieve GP version */
+						gp_version = mali_gp_core_get_version(gp_core);
+					}
+
+					gp_group = group;
+					gp_group_state = EXEC_STATE_INACTIVE;
+				}
+
+			}
+		}
+	}
+
+	num_physical_pp_cores_enabled = num_physical_pp_cores_total;
+}
+
+void mali_executor_depopulate(void)
+{
+	struct mali_group *group;
+	struct mali_group *temp;
+
+	MALI_DEBUG_ASSERT(EXEC_STATE_WORKING != gp_group_state);
+
+	if (NULL != gp_group) {
+		mali_group_delete(gp_group);
+		gp_group = NULL;
+	}
+
+	MALI_DEBUG_ASSERT(EXEC_STATE_WORKING != virtual_group_state);
+
+	if (NULL != virtual_group) {
+		mali_group_delete(virtual_group);
+		virtual_group = NULL;
+	}
+
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(&group_list_working));
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_idle, struct mali_group, executor_list) {
+		mali_group_delete(group);
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_inactive, struct mali_group, executor_list) {
+		mali_group_delete(group);
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_disabled, struct mali_group, executor_list) {
+		mali_group_delete(group);
+	}
+}
+
+void mali_executor_suspend(void)
+{
+	mali_executor_lock();
+
+	/* Increment the pause_count so that no more jobs will be scheduled */
+	pause_count++;
+
+	mali_executor_unlock();
+
+	_mali_osk_wait_queue_wait_event(executor_working_wait_queue,
+					mali_executor_is_suspended, NULL);
+
+	/*
+	 * mali_executor_complete_XX() leaves jobs in idle state.
+	 * deactivate option is used when we are going to power down
+	 * the entire GPU (OS suspend) and want a consistent SW vs HW
+	 * state.
+	 */
+	mali_executor_lock();
+
+	mali_executor_deactivate_list_idle(MALI_TRUE);
+
+	/*
+	 * The following steps are used to deactive all of activated
+	 * (MALI_GROUP_STATE_ACTIVE) and activating (MALI_GROUP
+	 * _STAET_ACTIVATION_PENDING) groups, to make sure the variable
+	 * pd_mask_wanted is equal with 0. */
+	if (MALI_GROUP_STATE_INACTIVE != mali_group_get_state(gp_group)) {
+		gp_group_state = EXEC_STATE_INACTIVE;
+		mali_group_deactivate(gp_group);
+	}
+
+	if (mali_executor_has_virtual_group()) {
+		if (MALI_GROUP_STATE_INACTIVE
+		    != mali_group_get_state(virtual_group)) {
+			virtual_group_state = EXEC_STATE_INACTIVE;
+			mali_group_deactivate(virtual_group);
+		}
+	}
+
+	if (0 < group_list_inactive_count) {
+		struct mali_group *group;
+		struct mali_group *temp;
+
+		_MALI_OSK_LIST_FOREACHENTRY(group, temp,
+					    &group_list_inactive,
+					    struct mali_group, executor_list) {
+			if (MALI_GROUP_STATE_ACTIVATION_PENDING
+			    == mali_group_get_state(group)) {
+				mali_group_deactivate(group);
+			}
+
+			/*
+			 * On mali-450 platform, we may have physical group in the group inactive
+			 * list, and its state is MALI_GROUP_STATE_ACTIVATION_PENDING, so we only
+			 * deactivate it is not enough, we still also need add it back to virtual group.
+			 * And now, virtual group must be in INACTIVE state, so it's safe to add
+			 * physical group to virtual group at this point.
+			 */
+			if (NULL != virtual_group) {
+				_mali_osk_list_delinit(&group->executor_list);
+				group_list_inactive_count--;
+
+				mali_group_add_group(virtual_group, group);
+			}
+		}
+	}
+
+	mali_executor_unlock();
+}
+
+void mali_executor_resume(void)
+{
+	mali_executor_lock();
+
+	/* Decrement pause_count to allow scheduling again (if it reaches 0) */
+	pause_count--;
+	if (0 == pause_count) {
+		mali_executor_schedule();
+	}
+
+	mali_executor_unlock();
+}
+
+u32 mali_executor_get_num_cores_total(void)
+{
+	return num_physical_pp_cores_total;
+}
+
+u32 mali_executor_get_num_cores_enabled(void)
+{
+	return num_physical_pp_cores_enabled;
+}
+
+struct mali_pp_core *mali_executor_get_virtual_pp(void)
+{
+	MALI_DEBUG_ASSERT_POINTER(virtual_group);
+	MALI_DEBUG_ASSERT_POINTER(virtual_group->pp_core);
+	return virtual_group->pp_core;
+}
+
+struct mali_group *mali_executor_get_virtual_group(void)
+{
+	return virtual_group;
+}
+
+void mali_executor_zap_all_active(struct mali_session_data *session)
+{
+	struct mali_group *group;
+	struct mali_group *temp;
+	mali_bool ret;
+
+	mali_executor_lock();
+
+	/*
+	 * This function is a bit complicated because
+	 * mali_group_zap_session() can fail. This only happens because the
+	 * group is in an unhandled page fault status.
+	 * We need to make sure this page fault is handled before we return,
+	 * so that we know every single outstanding MMU transactions have
+	 * completed. This will allow caller to safely remove physical pages
+	 * when we have returned.
+	 */
+
+	MALI_DEBUG_ASSERT(NULL != gp_group);
+	ret = mali_group_zap_session(gp_group, session);
+	if (MALI_FALSE == ret) {
+		struct mali_gp_job *gp_job = NULL;
+
+		mali_executor_complete_group(gp_group, MALI_FALSE, &gp_job, NULL);
+
+		MALI_DEBUG_ASSERT_POINTER(gp_job);
+
+		/* GP job completed, make sure it is freed */
+		mali_scheduler_complete_gp_job(gp_job, MALI_FALSE,
+					       MALI_TRUE, MALI_TRUE);
+	}
+
+	if (mali_executor_has_virtual_group()) {
+		ret = mali_group_zap_session(virtual_group, session);
+		if (MALI_FALSE == ret) {
+			struct mali_pp_job *pp_job = NULL;
+
+			mali_executor_complete_group(virtual_group, MALI_FALSE, NULL, &pp_job);
+
+			if (NULL != pp_job) {
+				/* PP job completed, make sure it is freed */
+				mali_scheduler_complete_pp_job(pp_job, 0,
+							       MALI_TRUE, MALI_TRUE);
+			}
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_working,
+				    struct mali_group, executor_list) {
+		ret = mali_group_zap_session(group, session);
+		if (MALI_FALSE == ret) {
+			ret = mali_group_zap_session(group, session);
+			if (MALI_FALSE == ret) {
+				struct mali_pp_job *pp_job = NULL;
+
+				mali_executor_complete_group(group, MALI_FALSE, NULL, &pp_job);
+
+				if (NULL != pp_job) {
+					/* PP job completed, free it */
+					mali_scheduler_complete_pp_job(pp_job,
+								       0, MALI_TRUE,
+								       MALI_TRUE);
+				}
+			}
+		}
+	}
+
+	mali_executor_unlock();
+}
+
+void mali_executor_schedule_from_mask(mali_scheduler_mask mask, mali_bool deferred_schedule)
+{
+	if (MALI_SCHEDULER_MASK_EMPTY != mask) {
+		if (MALI_TRUE == deferred_schedule) {
+			_mali_osk_wq_schedule_work_high_pri(executor_wq_high_pri);
+		} else {
+			/* Schedule from this thread*/
+			mali_executor_lock();
+			mali_executor_schedule();
+			mali_executor_unlock();
+		}
+	}
+}
+
+_mali_osk_errcode_t mali_executor_interrupt_gp(struct mali_group *group,
+		mali_bool in_upper_half)
+{
+	enum mali_interrupt_result int_result;
+	mali_bool time_out = MALI_FALSE;
+
+	MALI_DEBUG_PRINT(4, ("Executor: GP interrupt from %s in %s half\n",
+			     mali_group_core_description(group),
+			     in_upper_half ? "upper" : "bottom"));
+
+	mali_executor_lock();
+	if (!mali_group_is_working(group)) {
+		/* Not working, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_group_is_working(group));
+
+	if (mali_group_has_timed_out(group)) {
+		int_result = MALI_INTERRUPT_RESULT_ERROR;
+		time_out = MALI_TRUE;
+		MALI_PRINT(("Executor GP: Job %d Timeout on %s\n",
+			    mali_gp_job_get_id(group->gp_running_job),
+			    mali_group_core_description(group)));
+	} else {
+		int_result = mali_group_get_interrupt_result_gp(group);
+		if (MALI_INTERRUPT_RESULT_NONE == int_result) {
+			mali_executor_unlock();
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	if (MALI_INTERRUPT_RESULT_NONE == int_result) {
+		/* No interrupts signalled, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+#else
+	MALI_DEBUG_ASSERT(MALI_INTERRUPT_RESULT_NONE != int_result);
+#endif
+
+	mali_group_mask_all_interrupts_gp(group);
+
+	if (MALI_INTERRUPT_RESULT_SUCCESS_VS == int_result) {
+		if (mali_group_gp_is_active(group)) {
+			/* Only VS completed so far, while PLBU is still active */
+
+			/* Enable all but the current interrupt */
+			mali_group_enable_interrupts_gp(group, int_result);
+
+			mali_executor_unlock();
+			return _MALI_OSK_ERR_OK;
+		}
+	} else if (MALI_INTERRUPT_RESULT_SUCCESS_PLBU == int_result) {
+		if (mali_group_gp_is_active(group)) {
+			/* Only PLBU completed so far, while VS is still active */
+
+			/* Enable all but the current interrupt */
+			mali_group_enable_interrupts_gp(group, int_result);
+
+			mali_executor_unlock();
+			return _MALI_OSK_ERR_OK;
+		}
+	} else if (MALI_INTERRUPT_RESULT_OOM == int_result) {
+		struct mali_gp_job *job = mali_group_get_running_gp_job(group);
+
+		/* PLBU out of mem */
+		MALI_DEBUG_PRINT(3, ("Executor: PLBU needs more heap memory\n"));
+
+#if defined(CONFIG_MALI400_PROFILING)
+		/* Give group a chance to generate a SUSPEND event */
+		mali_group_oom(group);
+#endif
+
+		/*
+		 * no need to hold interrupt raised while
+		 * waiting for more memory.
+		 */
+		mali_executor_send_gp_oom_to_user(job);
+
+		mali_executor_unlock();
+
+		return _MALI_OSK_ERR_OK;
+	}
+
+	/* We should now have a real interrupt to handle */
+
+	MALI_DEBUG_PRINT(4, ("Executor: Group %s completed with %s\n",
+			     mali_group_core_description(group),
+			     (MALI_INTERRUPT_RESULT_ERROR == int_result) ?
+			     "ERROR" : "success"));
+
+	if (in_upper_half && MALI_INTERRUPT_RESULT_ERROR == int_result) {
+		/* Don't bother to do processing of errors in upper half */
+		mali_executor_unlock();
+
+		if (MALI_FALSE == time_out) {
+			mali_group_schedule_bottom_half_gp(group);
+		}
+	} else {
+		struct mali_gp_job *job;
+		mali_bool success;
+
+		if (MALI_TRUE == time_out) {
+			mali_group_dump_status(group);
+		}
+
+		success = (int_result != MALI_INTERRUPT_RESULT_ERROR) ?
+			  MALI_TRUE : MALI_FALSE;
+
+		mali_executor_complete_group(group, success, &job, NULL);
+
+		mali_executor_unlock();
+
+		/* GP jobs always fully complete */
+		MALI_DEBUG_ASSERT(NULL != job);
+
+		/* This will notify user space and close the job object */
+		mali_scheduler_complete_gp_job(job, success,
+					       MALI_TRUE, MALI_TRUE);
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_executor_interrupt_pp(struct mali_group *group,
+		mali_bool in_upper_half)
+{
+	enum mali_interrupt_result int_result;
+	mali_bool time_out = MALI_FALSE;
+
+	MALI_DEBUG_PRINT(4, ("Executor: PP interrupt from %s in %s half\n",
+			     mali_group_core_description(group),
+			     in_upper_half ? "upper" : "bottom"));
+
+	mali_executor_lock();
+
+	if (!mali_group_is_working(group)) {
+		/* Not working, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	if (in_upper_half) {
+		if (mali_group_is_in_virtual(group)) {
+			/* Child groups should never handle PP interrupts */
+			MALI_DEBUG_ASSERT(!mali_group_has_timed_out(group));
+			mali_executor_unlock();
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_group_is_working(group));
+	MALI_DEBUG_ASSERT(!mali_group_is_in_virtual(group));
+
+	if (mali_group_has_timed_out(group)) {
+		int_result = MALI_INTERRUPT_RESULT_ERROR;
+		time_out = MALI_TRUE;
+		MALI_PRINT(("Executor PP: Job %d Timeout on %s\n",
+			    mali_pp_job_get_id(group->pp_running_job),
+			    mali_group_core_description(group)));
+	} else {
+		int_result = mali_group_get_interrupt_result_pp(group);
+		if (MALI_INTERRUPT_RESULT_NONE == int_result) {
+			mali_executor_unlock();
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	if (MALI_INTERRUPT_RESULT_NONE == int_result) {
+		/* No interrupts signalled, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	} else if (MALI_INTERRUPT_RESULT_SUCCESS == int_result) {
+		if (mali_group_is_virtual(group) && mali_group_pp_is_active(group)) {
+			/* Some child groups are still working, so nothing to do right now */
+			mali_executor_unlock();
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+#else
+	MALI_DEBUG_ASSERT(MALI_INTERRUPT_RESULT_NONE != int_result);
+#endif
+
+	/* We should now have a real interrupt to handle */
+
+	MALI_DEBUG_PRINT(4, ("Executor: Group %s completed with %s\n",
+			     mali_group_core_description(group),
+			     (MALI_INTERRUPT_RESULT_ERROR == int_result) ?
+			     "ERROR" : "success"));
+
+	if (in_upper_half && MALI_INTERRUPT_RESULT_ERROR == int_result) {
+		/* Don't bother to do processing of errors in upper half */
+		mali_group_mask_all_interrupts_pp(group);
+		mali_executor_unlock();
+
+		if (MALI_FALSE == time_out) {
+			mali_group_schedule_bottom_half_pp(group);
+		}
+	} else {
+		struct mali_pp_job *job = NULL;
+		mali_bool success;
+
+		if (MALI_TRUE == time_out) {
+			mali_group_dump_status(group);
+		}
+
+		success = (int_result == MALI_INTERRUPT_RESULT_SUCCESS) ?
+			  MALI_TRUE : MALI_FALSE;
+
+		mali_executor_complete_group(group, success, NULL, &job);
+
+		mali_executor_unlock();
+
+		if (NULL != job) {
+			/* Notify user space and close the job object */
+			mali_scheduler_complete_pp_job(job,
+						       num_physical_pp_cores_total,
+						       MALI_TRUE, MALI_TRUE);
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_executor_interrupt_mmu(struct mali_group *group,
+		mali_bool in_upper_half)
+{
+	enum mali_interrupt_result int_result;
+
+	MALI_DEBUG_PRINT(4, ("Executor: MMU interrupt from %s in %s half\n",
+			     mali_group_core_description(group),
+			     in_upper_half ? "upper" : "bottom"));
+
+	mali_executor_lock();
+	if (!mali_group_is_working(group)) {
+		/* Not working, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_group_is_working(group));
+
+	int_result = mali_group_get_interrupt_result_mmu(group);
+	if (MALI_INTERRUPT_RESULT_NONE == int_result) {
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	if (MALI_INTERRUPT_RESULT_NONE == int_result) {
+		/* No interrupts signalled, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+#else
+	MALI_DEBUG_ASSERT(MALI_INTERRUPT_RESULT_ERROR == int_result);
+#endif
+
+	/* We should now have a real interrupt to handle */
+
+	if (in_upper_half) {
+		/* Don't bother to do processing of errors in upper half */
+
+		struct mali_group *parent = group->parent_group;
+
+		mali_mmu_mask_all_interrupts(group->mmu);
+
+		mali_executor_unlock();
+
+		if (NULL == parent) {
+			mali_group_schedule_bottom_half_mmu(group);
+		} else {
+			mali_group_schedule_bottom_half_mmu(parent);
+		}
+
+	} else {
+		struct mali_gp_job *gp_job = NULL;
+		struct mali_pp_job *pp_job = NULL;
+
+#ifdef DEBUG
+
+		u32 fault_address = mali_mmu_get_page_fault_addr(group->mmu);
+		u32 status = mali_mmu_get_status(group->mmu);
+		MALI_DEBUG_PRINT(2, ("Executor: Mali page fault detected at 0x%x from bus id %d of type %s on %s\n",
+				     (void *)(uintptr_t)fault_address,
+				     (status >> 6) & 0x1F,
+				     (status & 32) ? "write" : "read",
+				     group->mmu->hw_core.description));
+		MALI_DEBUG_PRINT(3, ("Executor: MMU rawstat = 0x%08X, MMU status = 0x%08X\n",
+				     mali_mmu_get_rawstat(group->mmu), status));
+		mali_mmu_pagedir_diag(mali_session_get_page_directory(group->session), fault_address);
+#endif
+
+		mali_executor_complete_group(group, MALI_FALSE, &gp_job, &pp_job);
+
+		mali_executor_unlock();
+
+		if (NULL != gp_job) {
+			MALI_DEBUG_ASSERT(NULL == pp_job);
+
+			/* Notify user space and close the job object */
+			mali_scheduler_complete_gp_job(gp_job, MALI_FALSE,
+						       MALI_TRUE, MALI_TRUE);
+		} else if (NULL != pp_job) {
+			MALI_DEBUG_ASSERT(NULL == gp_job);
+
+			/* Notify user space and close the job object */
+			mali_scheduler_complete_pp_job(pp_job,
+						       num_physical_pp_cores_total,
+						       MALI_TRUE, MALI_TRUE);
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_executor_group_power_up(struct mali_group *groups[], u32 num_groups)
+{
+	u32 i;
+	mali_bool child_groups_activated = MALI_FALSE;
+	mali_bool do_schedule = MALI_FALSE;
+#if defined(DEBUG)
+	u32 num_activated = 0;
+#endif
+
+	MALI_DEBUG_ASSERT_POINTER(groups);
+	MALI_DEBUG_ASSERT(0 < num_groups);
+
+	mali_executor_lock();
+
+	MALI_DEBUG_PRINT(3, ("Executor: powering up %u groups\n", num_groups));
+
+	for (i = 0; i < num_groups; i++) {
+		MALI_DEBUG_PRINT(3, ("Executor: powering up group %s\n",
+				     mali_group_core_description(groups[i])));
+
+		mali_group_power_up(groups[i]);
+
+		if ((MALI_GROUP_STATE_ACTIVATION_PENDING != mali_group_get_state(groups[i]) ||
+		     (MALI_TRUE != mali_executor_group_is_in_state(groups[i], EXEC_STATE_INACTIVE)))) {
+			/* nothing more to do for this group */
+			continue;
+		}
+
+		MALI_DEBUG_PRINT(3, ("Executor: activating group %s\n",
+				     mali_group_core_description(groups[i])));
+
+#if defined(DEBUG)
+		num_activated++;
+#endif
+
+		if (mali_group_is_in_virtual(groups[i])) {
+			/*
+			 * At least one child group of virtual group is powered on.
+			 */
+			child_groups_activated = MALI_TRUE;
+		} else if (MALI_FALSE == mali_group_is_virtual(groups[i])) {
+			/* Set gp and pp not in virtual to active. */
+			mali_group_set_active(groups[i]);
+		}
+
+		/* Move group from inactive to idle list */
+		if (groups[i] == gp_group) {
+			MALI_DEBUG_ASSERT(EXEC_STATE_INACTIVE ==
+					  gp_group_state);
+			gp_group_state = EXEC_STATE_IDLE;
+		} else if (MALI_FALSE == mali_group_is_in_virtual(groups[i])
+			   && MALI_FALSE == mali_group_is_virtual(groups[i])) {
+			MALI_DEBUG_ASSERT(MALI_TRUE == mali_executor_group_is_in_state(groups[i],
+					  EXEC_STATE_INACTIVE));
+
+			mali_executor_change_state_pp_physical(groups[i],
+							       &group_list_inactive,
+							       &group_list_inactive_count,
+							       &group_list_idle,
+							       &group_list_idle_count);
+		}
+
+		do_schedule = MALI_TRUE;
+	}
+
+	if (mali_executor_has_virtual_group() &&
+	    MALI_TRUE == child_groups_activated &&
+	    MALI_GROUP_STATE_ACTIVATION_PENDING ==
+	    mali_group_get_state(virtual_group)) {
+		/*
+		 * Try to active virtual group while it may be not sucessful every time,
+		 * because there is one situation that not all of child groups are powered on
+		 * in one time and virtual group is in activation pending state.
+		 */
+		if (mali_group_set_active(virtual_group)) {
+			/* Move group from inactive to idle */
+			MALI_DEBUG_ASSERT(EXEC_STATE_INACTIVE ==
+					  virtual_group_state);
+			virtual_group_state = EXEC_STATE_IDLE;
+
+			MALI_DEBUG_PRINT(3, ("Executor: powering up %u groups completed, %u  physical activated, 1 virtual activated.\n", num_groups, num_activated));
+		} else {
+			MALI_DEBUG_PRINT(3, ("Executor: powering up %u groups completed, %u physical activated\n", num_groups, num_activated));
+		}
+	} else {
+		MALI_DEBUG_PRINT(3, ("Executor: powering up %u groups completed, %u physical activated\n", num_groups, num_activated));
+	}
+
+	if (MALI_TRUE == do_schedule) {
+		/* Trigger a schedule */
+		mali_executor_schedule();
+	}
+
+	mali_executor_unlock();
+}
+
+void mali_executor_group_power_down(struct mali_group *groups[],
+				    u32 num_groups)
+{
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(groups);
+	MALI_DEBUG_ASSERT(0 < num_groups);
+
+	mali_executor_lock();
+
+	MALI_DEBUG_PRINT(3, ("Executor: powering down %u groups\n", num_groups));
+
+	for (i = 0; i < num_groups; i++) {
+		/* Groups must be either disabled or inactive. while for virtual group,
+		 * it maybe in empty state, because when we meet pm_runtime_suspend,
+		 * virtual group could be powered off, and before we acquire mali_executor_lock,
+		 * we must release mali_pm_state_lock, if there is a new physical job was queued,
+		 * all of physical groups in virtual group could be pulled out, so we only can
+		 * powered down an empty virtual group. Those physical groups will be powered
+		 * up in following pm_runtime_resume callback function.
+		 */
+		MALI_DEBUG_ASSERT(mali_executor_group_is_in_state(groups[i],
+				  EXEC_STATE_DISABLED) ||
+				  mali_executor_group_is_in_state(groups[i],
+						  EXEC_STATE_INACTIVE) ||
+				  mali_executor_group_is_in_state(groups[i],
+						  EXEC_STATE_EMPTY));
+
+		MALI_DEBUG_PRINT(3, ("Executor: powering down group %s\n",
+				     mali_group_core_description(groups[i])));
+
+		mali_group_power_down(groups[i]);
+	}
+
+	MALI_DEBUG_PRINT(3, ("Executor: powering down %u groups completed\n", num_groups));
+
+	mali_executor_unlock();
+}
+
+void mali_executor_abort_session(struct mali_session_data *session)
+{
+	struct mali_group *group;
+	struct mali_group *tmp_group;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT(session->is_aborting);
+
+	MALI_DEBUG_PRINT(3,
+			 ("Executor: Aborting all jobs from session 0x%08X.\n",
+			  session));
+
+	mali_executor_lock();
+
+	if (mali_group_get_session(gp_group) == session) {
+		if (EXEC_STATE_WORKING == gp_group_state) {
+			struct mali_gp_job *gp_job = NULL;
+
+			mali_executor_complete_group(gp_group, MALI_FALSE, &gp_job, NULL);
+
+			MALI_DEBUG_ASSERT_POINTER(gp_job);
+
+			/* GP job completed, make sure it is freed */
+			mali_scheduler_complete_gp_job(gp_job, MALI_FALSE,
+						       MALI_TRUE, MALI_TRUE);
+		} else {
+			/* Same session, but not working, so just clear it */
+			mali_group_clear_session(gp_group);
+		}
+	}
+
+	if (mali_executor_has_virtual_group()) {
+		if (EXEC_STATE_WORKING == virtual_group_state
+		    && mali_group_get_session(virtual_group) == session) {
+			struct mali_pp_job *pp_job = NULL;
+
+			mali_executor_complete_group(virtual_group, MALI_FALSE, NULL, &pp_job);
+
+			if (NULL != pp_job) {
+				/* PP job completed, make sure it is freed */
+				mali_scheduler_complete_pp_job(pp_job, 0,
+							       MALI_TRUE, MALI_TRUE);
+			}
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, tmp_group, &group_list_working,
+				    struct mali_group, executor_list) {
+		if (mali_group_get_session(group) == session) {
+			struct mali_pp_job *pp_job = NULL;
+
+			mali_executor_complete_group(group, MALI_FALSE, NULL, &pp_job);
+
+			if (NULL != pp_job) {
+				/* PP job completed, make sure it is freed */
+				mali_scheduler_complete_pp_job(pp_job, 0,
+							       MALI_TRUE, MALI_TRUE);
+			}
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, tmp_group, &group_list_idle, struct mali_group, executor_list) {
+		mali_group_clear_session(group);
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, tmp_group, &group_list_inactive, struct mali_group, executor_list) {
+		mali_group_clear_session(group);
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, tmp_group, &group_list_disabled, struct mali_group, executor_list) {
+		mali_group_clear_session(group);
+	}
+
+	mali_executor_unlock();
+}
+
+
+void mali_executor_core_scaling_enable(void)
+{
+	/* PS: Core scaling is by default enabled */
+	core_scaling_enabled = MALI_TRUE;
+}
+
+void mali_executor_core_scaling_disable(void)
+{
+	core_scaling_enabled = MALI_FALSE;
+}
+
+mali_bool mali_executor_core_scaling_is_enabled(void)
+{
+	return core_scaling_enabled;
+}
+
+void mali_executor_group_enable(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	mali_executor_lock();
+
+	if ((NULL != mali_group_get_gp_core(group) || NULL != mali_group_get_pp_core(group))
+	    && (mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED))) {
+		mali_executor_group_enable_internal(group);
+	}
+
+	mali_executor_schedule();
+	mali_executor_unlock();
+
+	_mali_osk_wq_schedule_work(executor_wq_notify_core_change);
+}
+
+/*
+ * If a physical group is inactive or idle, we should disable it immediately,
+ * if group is in virtual, and virtual group is idle, disable given physical group in it.
+ */
+void mali_executor_group_disable(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	mali_executor_lock();
+
+	if ((NULL != mali_group_get_gp_core(group) || NULL != mali_group_get_pp_core(group))
+	    && (!mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED))) {
+		mali_executor_group_disable_internal(group);
+	}
+
+	mali_executor_schedule();
+	mali_executor_unlock();
+
+	_mali_osk_wq_schedule_work(executor_wq_notify_core_change);
+}
+
+mali_bool mali_executor_group_is_disabled(struct mali_group *group)
+{
+	/* NB: This function is not optimized for time critical usage */
+
+	mali_bool ret;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	mali_executor_lock();
+	ret = mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED);
+	mali_executor_unlock();
+
+	return ret;
+}
+
+int mali_executor_set_perf_level(unsigned int target_core_nr, mali_bool override)
+{
+	if (target_core_nr == num_physical_pp_cores_enabled) return 0;
+	if (MALI_FALSE == core_scaling_enabled && MALI_FALSE == override) return -EPERM;
+	if (target_core_nr > num_physical_pp_cores_total) return -EINVAL;
+	if (0 == target_core_nr) return -EINVAL;
+
+	mali_executor_core_scale(target_core_nr);
+
+	_mali_osk_wq_schedule_work(executor_wq_notify_core_change);
+
+	return 0;
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_executor_dump_state(char *buf, u32 size)
+{
+	int n = 0;
+	struct mali_group *group;
+	struct mali_group *temp;
+
+	mali_executor_lock();
+
+	switch (gp_group_state) {
+	case EXEC_STATE_INACTIVE:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"GP group is in state INACTIVE\n");
+		break;
+	case EXEC_STATE_IDLE:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"GP group is in state IDLE\n");
+		break;
+	case EXEC_STATE_WORKING:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"GP group is in state WORKING\n");
+		break;
+	default:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"GP group is in unknown/illegal state %u\n",
+					gp_group_state);
+		break;
+	}
+
+	n += mali_group_dump_state(gp_group, buf + n, size - n);
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"Physical PP groups in WORKING state (count = %u):\n",
+				group_list_working_count);
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_working, struct mali_group, executor_list) {
+		n += mali_group_dump_state(group, buf + n, size - n);
+	}
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"Physical PP groups in IDLE state (count = %u):\n",
+				group_list_idle_count);
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_idle, struct mali_group, executor_list) {
+		n += mali_group_dump_state(group, buf + n, size - n);
+	}
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"Physical PP groups in INACTIVE state (count = %u):\n",
+				group_list_inactive_count);
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_inactive, struct mali_group, executor_list) {
+		n += mali_group_dump_state(group, buf + n, size - n);
+	}
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"Physical PP groups in DISABLED state (count = %u):\n",
+				group_list_disabled_count);
+
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_disabled, struct mali_group, executor_list) {
+		n += mali_group_dump_state(group, buf + n, size - n);
+	}
+
+	if (mali_executor_has_virtual_group()) {
+		struct mali_group *child;
+
+		switch (virtual_group_state) {
+		case EXEC_STATE_EMPTY:
+			n += _mali_osk_snprintf(buf + n, size - n,
+						"Virtual PP group is in state EMPTY\n");
+			break;
+		case EXEC_STATE_INACTIVE:
+			n += _mali_osk_snprintf(buf + n, size - n,
+						"Virtual PP group is in state INACTIVE\n");
+			break;
+		case EXEC_STATE_IDLE:
+			n += _mali_osk_snprintf(buf + n, size - n,
+						"Virtual PP group is in state IDLE\n");
+			break;
+		case EXEC_STATE_WORKING:
+			n += _mali_osk_snprintf(buf + n, size - n,
+						"Virtual PP group is in state WORKING\n");
+			break;
+		default:
+			n += _mali_osk_snprintf(buf + n, size - n,
+						"Virtual PP group is in unknown/illegal state %u\n",
+						virtual_group_state);
+			break;
+		}
+
+		n += mali_group_dump_state(virtual_group, buf + n, size - n);
+
+
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &virtual_group->group_list,
+					    struct mali_group, group_list) {
+			n += mali_group_dump_state(child, buf + n, size - n);
+		}
+	}
+
+	mali_executor_unlock();
+
+	n += _mali_osk_snprintf(buf + n, size - n, "\n");
+
+	return n;
+}
+#endif
+
+_mali_osk_errcode_t _mali_ukk_get_pp_number_of_cores(_mali_uk_get_pp_number_of_cores_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+	args->number_of_total_cores = num_physical_pp_cores_total;
+	args->number_of_enabled_cores = num_physical_pp_cores_enabled;
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_get_pp_core_version(_mali_uk_get_pp_core_version_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+	args->version = pp_version;
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_get_gp_number_of_cores(_mali_uk_get_gp_number_of_cores_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+	args->number_of_cores = 1;
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_get_gp_core_version(_mali_uk_get_gp_core_version_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+	args->version = gp_version;
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_gp_suspend_response(_mali_uk_gp_suspend_response_s *args)
+{
+	struct mali_session_data *session;
+	struct mali_gp_job *job;
+
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)args->ctx;
+
+	if (_MALIGP_JOB_RESUME_WITH_NEW_HEAP == args->code) {
+		_mali_osk_notification_t *new_notification = NULL;
+
+		new_notification = _mali_osk_notification_create(
+					   _MALI_NOTIFICATION_GP_STALLED,
+					   sizeof(_mali_uk_gp_job_suspended_s));
+
+		if (NULL != new_notification) {
+			MALI_DEBUG_PRINT(3, ("Executor: Resuming job %u with new heap; 0x%08X - 0x%08X\n",
+					     args->cookie, args->arguments[0], args->arguments[1]));
+
+			mali_executor_lock();
+
+			/* Resume the job in question if it is still running */
+			job = mali_group_get_running_gp_job(gp_group);
+			if (NULL != job &&
+			    args->cookie == mali_gp_job_get_id(job) &&
+			    session == mali_gp_job_get_session(job)) {
+				/*
+				 * Correct job is running, resume with new heap
+				 */
+
+				mali_gp_job_set_oom_notification(job,
+								 new_notification);
+
+				/* This will also re-enable interrupts */
+				mali_group_resume_gp_with_new_heap(gp_group,
+								   args->cookie,
+								   args->arguments[0],
+								   args->arguments[1]);
+
+				mali_executor_unlock();
+				return _MALI_OSK_ERR_OK;
+			} else {
+				MALI_DEBUG_PRINT(2, ("Executor: Unable to resume  gp job becasue gp time out or any other unexpected reason!\n"));
+
+				_mali_osk_notification_delete(new_notification);
+
+				mali_executor_unlock();
+				return _MALI_OSK_ERR_FAULT;
+			}
+		} else {
+			MALI_PRINT_ERROR(("Executor: Failed to allocate notification object. Will abort GP job.\n"));
+		}
+	} else {
+		MALI_DEBUG_PRINT(2, ("Executor: Aborting job %u, no new heap provided\n", args->cookie));
+	}
+
+	mali_executor_lock();
+
+	/* Abort the job in question if it is still running */
+	job = mali_group_get_running_gp_job(gp_group);
+	if (NULL != job &&
+	    args->cookie == mali_gp_job_get_id(job) &&
+	    session == mali_gp_job_get_session(job)) {
+		/* Correct job is still running */
+		struct mali_gp_job *job_done = NULL;
+
+		mali_executor_complete_group(gp_group, MALI_FALSE, &job_done, NULL);
+
+		/* The same job should have completed */
+		MALI_DEBUG_ASSERT(job_done == job);
+
+		/* GP job completed, make sure it is freed */
+		mali_scheduler_complete_gp_job(job_done, MALI_FALSE,
+					       MALI_TRUE, MALI_TRUE);
+	}
+
+	mali_executor_unlock();
+	return _MALI_OSK_ERR_FAULT;
+}
+
+
+/*
+ * ---------- Implementation of static functions ----------
+ */
+
+void mali_executor_lock(void)
+{
+	_mali_osk_spinlock_irq_lock(mali_executor_lock_obj);
+	MALI_DEBUG_PRINT(5, ("Executor: lock taken\n"));
+}
+
+void mali_executor_unlock(void)
+{
+	MALI_DEBUG_PRINT(5, ("Executor: Releasing lock\n"));
+	_mali_osk_spinlock_irq_unlock(mali_executor_lock_obj);
+}
+
+static mali_bool mali_executor_is_suspended(void *data)
+{
+	mali_bool ret;
+
+	/* This callback does not use the data pointer. */
+	MALI_IGNORE(data);
+
+	mali_executor_lock();
+
+	ret = pause_count > 0 && !mali_executor_is_working();
+
+	mali_executor_unlock();
+
+	return ret;
+}
+
+static mali_bool mali_executor_is_working()
+{
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	return (0 != group_list_working_count ||
+		EXEC_STATE_WORKING == gp_group_state ||
+		EXEC_STATE_WORKING == virtual_group_state);
+}
+
+static void mali_executor_disable_empty_virtual(void)
+{
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(virtual_group_state != EXEC_STATE_EMPTY);
+	MALI_DEBUG_ASSERT(virtual_group_state != EXEC_STATE_WORKING);
+
+	if (mali_group_is_empty(virtual_group)) {
+		virtual_group_state = EXEC_STATE_EMPTY;
+	}
+}
+
+static mali_bool mali_executor_physical_rejoin_virtual(struct mali_group *group)
+{
+	mali_bool trigger_pm_update = MALI_FALSE;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	/* Only rejoining after job has completed (still active) */
+	MALI_DEBUG_ASSERT(MALI_GROUP_STATE_ACTIVE ==
+			  mali_group_get_state(group));
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(MALI_TRUE == mali_executor_has_virtual_group());
+	MALI_DEBUG_ASSERT(MALI_FALSE == mali_group_is_virtual(group));
+
+	/* Make sure group and virtual group have same status */
+
+	if (MALI_GROUP_STATE_INACTIVE == mali_group_get_state(virtual_group)) {
+		if (mali_group_deactivate(group)) {
+			trigger_pm_update = MALI_TRUE;
+		}
+
+		if (virtual_group_state == EXEC_STATE_EMPTY) {
+			virtual_group_state = EXEC_STATE_INACTIVE;
+		}
+	} else if (MALI_GROUP_STATE_ACTIVATION_PENDING ==
+		   mali_group_get_state(virtual_group)) {
+		/*
+		 * Activation is pending for virtual group, leave
+		 * this child group as active.
+		 */
+		if (virtual_group_state == EXEC_STATE_EMPTY) {
+			virtual_group_state = EXEC_STATE_INACTIVE;
+		}
+	} else {
+		MALI_DEBUG_ASSERT(MALI_GROUP_STATE_ACTIVE ==
+				  mali_group_get_state(virtual_group));
+
+		if (virtual_group_state == EXEC_STATE_EMPTY) {
+			virtual_group_state = EXEC_STATE_IDLE;
+		}
+	}
+
+	/* Remove group from idle list */
+	MALI_DEBUG_ASSERT(mali_executor_group_is_in_state(group,
+			  EXEC_STATE_IDLE));
+	_mali_osk_list_delinit(&group->executor_list);
+	group_list_idle_count--;
+
+	/*
+	 * And finally rejoin the virtual group
+	 * group will start working on same job as virtual_group,
+	 * if virtual_group is working on a job
+	 */
+	mali_group_add_group(virtual_group, group);
+
+	return trigger_pm_update;
+}
+
+static mali_bool mali_executor_has_virtual_group(void)
+{
+#if (defined(CONFIG_MALI450) || defined(CONFIG_MALI470))
+	return (NULL != virtual_group) ? MALI_TRUE : MALI_FALSE;
+#else
+	return MALI_FALSE;
+#endif /* (defined(CONFIG_MALI450) || defined(CONFIG_MALI470)) */
+}
+
+static mali_bool mali_executor_virtual_group_is_usable(void)
+{
+#if (defined(CONFIG_MALI450) || defined(CONFIG_MALI470))
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return ((EXEC_STATE_INACTIVE == virtual_group_state ||
+		 EXEC_STATE_IDLE == virtual_group_state) && (virtual_group->state != MALI_GROUP_STATE_ACTIVATION_PENDING)) ?
+	       MALI_TRUE : MALI_FALSE;
+#else
+	return MALI_FALSE;
+#endif /* (defined(CONFIG_MALI450) || defined(CONFIG_MALI470)) */
+}
+
+static mali_bool mali_executor_tackle_gp_bound(void)
+{
+	struct mali_pp_job *job;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	job = mali_scheduler_job_pp_physical_peek();
+
+	if (NULL != job && MALI_TRUE == mali_is_mali400()) {
+		if (0 < group_list_working_count &&
+		    mali_pp_job_is_large_and_unstarted(job)) {
+			return MALI_TRUE;
+		}
+	}
+
+	return MALI_FALSE;
+}
+
+static mali_bool mali_executor_schedule_is_early_out(mali_bool *gpu_secure_mode_is_needed)
+{
+	struct mali_pp_job *next_pp_job_to_start = NULL;
+	struct mali_group *group;
+	struct mali_group *tmp_group;
+	struct mali_pp_job *physical_pp_job_working = NULL;
+	struct mali_pp_job *virtual_pp_job_working = NULL;
+	mali_bool gpu_working_in_protected_mode = MALI_FALSE;
+	mali_bool gpu_working_in_non_protected_mode = MALI_FALSE;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+
+	*gpu_secure_mode_is_needed = MALI_FALSE;
+
+	/* Check if the gpu secure mode is supported, exit if not.*/
+	if (MALI_FALSE == _mali_osk_gpu_secure_mode_is_supported()) {
+		return MALI_FALSE;
+	}
+
+	/* Check if need to set gpu secure mode for the next pp job,
+	 * get the next pp job that will be scheduled  if exist.
+	 */
+	next_pp_job_to_start = mali_scheduler_job_pp_next();
+
+	/* Check current pp physical/virtual running job is protected job or not if exist.*/
+	_MALI_OSK_LIST_FOREACHENTRY(group, tmp_group, &group_list_working,
+				    struct mali_group, executor_list) {
+		physical_pp_job_working = group->pp_running_job;
+		break;
+	}
+
+	if (EXEC_STATE_WORKING == virtual_group_state) {
+		virtual_pp_job_working = virtual_group->pp_running_job;
+	}
+
+	if (NULL != physical_pp_job_working) {
+		if (MALI_TRUE == mali_pp_job_is_protected_job(physical_pp_job_working)) {
+			gpu_working_in_protected_mode = MALI_TRUE;
+		} else {
+			gpu_working_in_non_protected_mode = MALI_TRUE;
+		}
+	} else if (NULL != virtual_pp_job_working) {
+		if (MALI_TRUE == mali_pp_job_is_protected_job(virtual_pp_job_working)) {
+			gpu_working_in_protected_mode = MALI_TRUE;
+		} else {
+			gpu_working_in_non_protected_mode = MALI_TRUE;
+		}
+	} else if (EXEC_STATE_WORKING == gp_group_state) {
+		gpu_working_in_non_protected_mode = MALI_TRUE;
+	}
+
+	/* If the next pp job is the protected pp job.*/
+	if ((NULL != next_pp_job_to_start) && MALI_TRUE == mali_pp_job_is_protected_job(next_pp_job_to_start)) {
+		/* if gp is working or any non-protected pp job is working now, unable to schedule protected pp job. */
+		if (MALI_TRUE == gpu_working_in_non_protected_mode)
+			return MALI_TRUE;
+
+		*gpu_secure_mode_is_needed = MALI_TRUE;
+		return MALI_FALSE;
+
+	}
+
+	if (MALI_TRUE == gpu_working_in_protected_mode) {
+		/* Unable to schedule non-protected pp job/gp job if exist protected pp running jobs*/
+		return MALI_TRUE;
+	}
+
+	return MALI_FALSE;
+}
+/*
+ * This is where jobs are actually started.
+ */
+static void mali_executor_schedule(void)
+{
+	u32 i;
+	u32 num_physical_needed = 0;
+	u32 num_physical_to_process = 0;
+	mali_bool trigger_pm_update = MALI_FALSE;
+	mali_bool deactivate_idle_group = MALI_TRUE;
+	mali_bool gpu_secure_mode_is_needed = MALI_FALSE;
+	mali_bool is_gpu_secure_mode = MALI_FALSE;
+	/* Physical groups + jobs to start in this function */
+	struct mali_group *groups_to_start[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS];
+	struct mali_pp_job *jobs_to_start[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS];
+	u32 sub_jobs_to_start[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS];
+	int num_jobs_to_start = 0;
+
+	/* Virtual job to start in this function */
+	struct mali_pp_job *virtual_job_to_start = NULL;
+
+	/* GP job to start in this function */
+	struct mali_gp_job *gp_job_to_start = NULL;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	if (pause_count > 0) {
+		/* Execution is suspended, don't schedule any jobs. */
+		return;
+	}
+
+	/* Lock needed in order to safely handle the job queues */
+	mali_scheduler_lock();
+
+	/* 1. Check the schedule if need to early out. */
+	if (MALI_TRUE == mali_executor_schedule_is_early_out(&gpu_secure_mode_is_needed)) {
+		mali_scheduler_unlock();
+		return;
+	}
+
+	/* 2. Activate gp firstly if have gp job queued. */
+	if ((EXEC_STATE_INACTIVE == gp_group_state)
+	    && (0 < mali_scheduler_job_gp_count())
+	    && (gpu_secure_mode_is_needed == MALI_FALSE)) {
+
+		enum mali_group_state state =
+			mali_group_activate(gp_group);
+		if (MALI_GROUP_STATE_ACTIVE == state) {
+			/* Set GP group state to idle */
+			gp_group_state = EXEC_STATE_IDLE;
+		} else {
+			trigger_pm_update = MALI_TRUE;
+		}
+	}
+
+	/* 3. Prepare as many physical groups as needed/possible */
+
+	num_physical_needed = mali_scheduler_job_physical_head_count(gpu_secure_mode_is_needed);
+
+	/* On mali-450 platform, we don't need to enter in this block frequently. */
+	if (0 < num_physical_needed) {
+
+		if (num_physical_needed <= group_list_idle_count) {
+			/* We have enough groups on idle list already */
+			num_physical_to_process = num_physical_needed;
+			num_physical_needed = 0;
+		} else {
+			/* We need to get a hold of some more groups */
+			num_physical_to_process = group_list_idle_count;
+			num_physical_needed -= group_list_idle_count;
+		}
+
+		if (0 < num_physical_needed) {
+
+			/* 3.1. Activate groups which are inactive */
+
+			struct mali_group *group;
+			struct mali_group *temp;
+
+			_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_inactive,
+						    struct mali_group, executor_list) {
+				enum mali_group_state state =
+					mali_group_activate(group);
+				if (MALI_GROUP_STATE_ACTIVE == state) {
+					/* Move from inactive to idle */
+					mali_executor_change_state_pp_physical(group,
+									       &group_list_inactive,
+									       &group_list_inactive_count,
+									       &group_list_idle,
+									       &group_list_idle_count);
+					num_physical_to_process++;
+				} else {
+					trigger_pm_update = MALI_TRUE;
+				}
+
+				num_physical_needed--;
+				if (0 == num_physical_needed) {
+					/* We have activated all the groups we need */
+					break;
+				}
+			}
+		}
+
+		if (mali_executor_virtual_group_is_usable()) {
+
+			/*
+			 * 3.2. And finally, steal and activate groups
+			 * from virtual group if we need even more
+			 */
+			while (0 < num_physical_needed) {
+				struct mali_group *group;
+
+				group = mali_group_acquire_group(virtual_group);
+				if (NULL != group) {
+					enum mali_group_state state;
+
+					mali_executor_disable_empty_virtual();
+
+					state = mali_group_activate(group);
+					if (MALI_GROUP_STATE_ACTIVE == state) {
+						/* Group is ready, add to idle list */
+						_mali_osk_list_add(
+							&group->executor_list,
+							&group_list_idle);
+						group_list_idle_count++;
+						num_physical_to_process++;
+					} else {
+						/*
+						 * Group is not ready yet,
+						 * add to inactive list
+						 */
+						_mali_osk_list_add(
+							&group->executor_list,
+							&group_list_inactive);
+						group_list_inactive_count++;
+
+						trigger_pm_update = MALI_TRUE;
+					}
+					num_physical_needed--;
+				} else {
+					/*
+					 * We could not get enough groups
+					 * from the virtual group.
+					 */
+					break;
+				}
+			}
+		}
+
+		/* 3.3. Assign physical jobs to groups */
+
+		if (0 < num_physical_to_process) {
+			struct mali_group *group;
+			struct mali_group *temp;
+
+			_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_idle,
+						    struct mali_group, executor_list) {
+				struct mali_pp_job *job = NULL;
+				u32 sub_job = MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS;
+
+				MALI_DEBUG_ASSERT(num_jobs_to_start <
+						  MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS);
+
+				MALI_DEBUG_ASSERT(0 <
+						  mali_scheduler_job_physical_head_count(gpu_secure_mode_is_needed));
+
+				/* If the next pp job is non-protected, check if gp bound now. */
+				if ((MALI_FALSE == gpu_secure_mode_is_needed)
+				    && (mali_executor_hint_is_enabled(MALI_EXECUTOR_HINT_GP_BOUND))
+				    && (MALI_TRUE == mali_executor_tackle_gp_bound())) {
+					/*
+					* We're gp bound,
+					* don't start this right now.
+					*/
+					deactivate_idle_group = MALI_FALSE;
+					num_physical_to_process = 0;
+					break;
+				}
+
+				job = mali_scheduler_job_pp_physical_get(
+					      &sub_job);
+
+				if (MALI_FALSE == gpu_secure_mode_is_needed) {
+					MALI_DEBUG_ASSERT(MALI_FALSE == mali_pp_job_is_protected_job(job));
+				} else {
+					MALI_DEBUG_ASSERT(MALI_TRUE == mali_pp_job_is_protected_job(job));
+				}
+
+				MALI_DEBUG_ASSERT_POINTER(job);
+				MALI_DEBUG_ASSERT(sub_job <= MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS);
+
+				/* Put job + group on list of jobs to start later on */
+
+				groups_to_start[num_jobs_to_start] = group;
+				jobs_to_start[num_jobs_to_start] = job;
+				sub_jobs_to_start[num_jobs_to_start] = sub_job;
+				num_jobs_to_start++;
+
+				/* Move group from idle to working */
+				mali_executor_change_state_pp_physical(group,
+								       &group_list_idle,
+								       &group_list_idle_count,
+								       &group_list_working,
+								       &group_list_working_count);
+
+				num_physical_to_process--;
+				if (0 == num_physical_to_process) {
+					/* Got all we needed */
+					break;
+				}
+			}
+		}
+	}
+
+	/* 4. Deactivate idle pp group , must put deactive here before active vitual group
+	 *    for cover case first only has physical job in normal queue but group inactive,
+	 *    so delay the job start go to active group, when group activated,
+	 *    call scheduler again, but now if we get high queue virtual job,
+	 *    we will do nothing in schedule cause executor schedule stop
+	 */
+
+	if (MALI_TRUE == mali_executor_deactivate_list_idle(deactivate_idle_group
+			&& (!mali_timeline_has_physical_pp_job()))) {
+		trigger_pm_update = MALI_TRUE;
+	}
+
+	/* 5. Activate virtual group, if needed */
+	if (EXEC_STATE_INACTIVE == virtual_group_state &&
+	    MALI_TRUE ==  mali_scheduler_job_next_is_virtual()) {
+		struct mali_pp_job *virtual_job = mali_scheduler_job_pp_virtual_peek();
+		if ((MALI_FALSE == gpu_secure_mode_is_needed && MALI_FALSE == mali_pp_job_is_protected_job(virtual_job))
+		    || (MALI_TRUE == gpu_secure_mode_is_needed && MALI_TRUE == mali_pp_job_is_protected_job(virtual_job))) {
+			enum mali_group_state state =
+				mali_group_activate(virtual_group);
+			if (MALI_GROUP_STATE_ACTIVE == state) {
+				/* Set virtual group state to idle */
+				virtual_group_state = EXEC_STATE_IDLE;
+			} else {
+				trigger_pm_update = MALI_TRUE;
+			}
+		}
+	}
+
+	/* 6. To power up group asap,  trigger pm update only when no need to swith the gpu mode. */
+
+	is_gpu_secure_mode = _mali_osk_gpu_secure_mode_is_enabled();
+
+	if ((MALI_FALSE == gpu_secure_mode_is_needed && MALI_FALSE == is_gpu_secure_mode)
+	    || (MALI_TRUE == gpu_secure_mode_is_needed && MALI_TRUE == is_gpu_secure_mode)) {
+		if (MALI_TRUE == trigger_pm_update) {
+			trigger_pm_update = MALI_FALSE;
+			mali_pm_update_async();
+		}
+	}
+
+	/* 7. Assign jobs to idle virtual group (or deactivate if no job) */
+
+	if (EXEC_STATE_IDLE == virtual_group_state) {
+		if (MALI_TRUE == mali_scheduler_job_next_is_virtual()) {
+			struct mali_pp_job *virtual_job = mali_scheduler_job_pp_virtual_peek();
+			if ((MALI_FALSE == gpu_secure_mode_is_needed && MALI_FALSE == mali_pp_job_is_protected_job(virtual_job))
+			    || (MALI_TRUE == gpu_secure_mode_is_needed && MALI_TRUE == mali_pp_job_is_protected_job(virtual_job))) {
+				virtual_job_to_start =
+					mali_scheduler_job_pp_virtual_get();
+				virtual_group_state = EXEC_STATE_WORKING;
+			}
+		} else if (!mali_timeline_has_virtual_pp_job()) {
+			virtual_group_state = EXEC_STATE_INACTIVE;
+
+			if (mali_group_deactivate(virtual_group)) {
+				trigger_pm_update = MALI_TRUE;
+			}
+		}
+	}
+
+	/* 8. Assign job to idle GP group (or deactivate if no job) */
+
+	if (EXEC_STATE_IDLE == gp_group_state && MALI_FALSE == gpu_secure_mode_is_needed) {
+		if (0 < mali_scheduler_job_gp_count()) {
+			gp_job_to_start = mali_scheduler_job_gp_get();
+			gp_group_state = EXEC_STATE_WORKING;
+		} else if (!mali_timeline_has_gp_job()) {
+			gp_group_state = EXEC_STATE_INACTIVE;
+			if (mali_group_deactivate(gp_group)) {
+				trigger_pm_update = MALI_TRUE;
+			}
+		}
+	}
+
+	/* 9. We no longer need the schedule/queue lock */
+
+	mali_scheduler_unlock();
+
+	/* 10. start jobs */
+	if (NULL != virtual_job_to_start) {
+		MALI_DEBUG_ASSERT(!mali_group_pp_is_active(virtual_group));
+		mali_group_start_pp_job(virtual_group,
+					virtual_job_to_start, 0, is_gpu_secure_mode);
+	}
+
+	for (i = 0; i < num_jobs_to_start; i++) {
+		MALI_DEBUG_ASSERT(!mali_group_pp_is_active(
+					  groups_to_start[i]));
+		mali_group_start_pp_job(groups_to_start[i],
+					jobs_to_start[i],
+					sub_jobs_to_start[i], is_gpu_secure_mode);
+	}
+
+	MALI_DEBUG_ASSERT_POINTER(gp_group);
+
+	if (NULL != gp_job_to_start) {
+		MALI_DEBUG_ASSERT(!mali_group_gp_is_active(gp_group));
+		mali_group_start_gp_job(gp_group, gp_job_to_start, is_gpu_secure_mode);
+	}
+
+	/* 11. Trigger any pending PM updates */
+	if (MALI_TRUE == trigger_pm_update) {
+		mali_pm_update_async();
+	}
+}
+
+/* Handler for deferred schedule requests */
+static void mali_executor_wq_schedule(void *arg)
+{
+	MALI_IGNORE(arg);
+	mali_executor_lock();
+	mali_executor_schedule();
+	mali_executor_unlock();
+}
+
+static void mali_executor_send_gp_oom_to_user(struct mali_gp_job *job)
+{
+	_mali_uk_gp_job_suspended_s *jobres;
+	_mali_osk_notification_t *notification;
+
+	notification = mali_gp_job_get_oom_notification(job);
+
+	/*
+	 * Remember the id we send to user space, so we have something to
+	 * verify when we get a response
+	 */
+	gp_returned_cookie = mali_gp_job_get_id(job);
+
+	jobres = (_mali_uk_gp_job_suspended_s *)notification->result_buffer;
+	jobres->user_job_ptr = mali_gp_job_get_user_id(job);
+	jobres->cookie = gp_returned_cookie;
+
+	mali_session_send_notification(mali_gp_job_get_session(job),
+				       notification);
+}
+static struct mali_gp_job *mali_executor_complete_gp(struct mali_group *group,
+		mali_bool success)
+{
+	struct mali_gp_job *job;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	/* Extracts the needed HW status from core and reset */
+	job = mali_group_complete_gp(group, success);
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	/* Core is now ready to go into idle list */
+	gp_group_state = EXEC_STATE_IDLE;
+
+	/* This will potentially queue more GP and PP jobs */
+	mali_timeline_tracker_release(&job->tracker);
+
+	/* Signal PP job */
+	mali_gp_job_signal_pp_tracker(job, success);
+
+	return job;
+}
+
+static struct mali_pp_job *mali_executor_complete_pp(struct mali_group *group,
+		mali_bool success)
+{
+	struct mali_pp_job *job;
+	u32 sub_job;
+	mali_bool job_is_done;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	/* Extracts the needed HW status from core and reset */
+	job = mali_group_complete_pp(group, success, &sub_job);
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	/* Core is now ready to go into idle list */
+	if (mali_group_is_virtual(group)) {
+		virtual_group_state = EXEC_STATE_IDLE;
+	} else {
+		/* Move from working to idle state */
+		mali_executor_change_state_pp_physical(group,
+						       &group_list_working,
+						       &group_list_working_count,
+						       &group_list_idle,
+						       &group_list_idle_count);
+	}
+
+	/* It is the executor module which owns the jobs themselves by now */
+	mali_pp_job_mark_sub_job_completed(job, success);
+	job_is_done = mali_pp_job_is_complete(job);
+
+	if (job_is_done) {
+		/* This will potentially queue more GP and PP jobs */
+		mali_timeline_tracker_release(&job->tracker);
+	}
+
+	return job;
+}
+
+static void mali_executor_complete_group(struct mali_group *group,
+		mali_bool success,
+		struct mali_gp_job **gp_job_done,
+		struct mali_pp_job **pp_job_done)
+{
+	struct mali_gp_core *gp_core = mali_group_get_gp_core(group);
+	struct mali_pp_core *pp_core = mali_group_get_pp_core(group);
+	struct mali_gp_job *gp_job = NULL;
+	struct mali_pp_job *pp_job = NULL;
+	mali_bool pp_job_is_done = MALI_TRUE;
+
+	if (NULL != gp_core) {
+		gp_job = mali_executor_complete_gp(group, success);
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(pp_core);
+		MALI_IGNORE(pp_core);
+		pp_job = mali_executor_complete_pp(group, success);
+
+		pp_job_is_done = mali_pp_job_is_complete(pp_job);
+	}
+
+	if (pause_count > 0) {
+		/* Execution has been suspended */
+
+		if (!mali_executor_is_working()) {
+			/* Last job completed, wake up sleepers */
+			_mali_osk_wait_queue_wake_up(
+				executor_working_wait_queue);
+		}
+	} else if (MALI_TRUE == mali_group_disable_requested(group)) {
+		mali_executor_core_scale_in_group_complete(group);
+
+		mali_executor_schedule();
+	} else {
+		/* try to schedule new jobs */
+		mali_executor_schedule();
+	}
+
+	if (NULL != gp_job) {
+		MALI_DEBUG_ASSERT_POINTER(gp_job_done);
+		*gp_job_done = gp_job;
+	} else if (pp_job_is_done) {
+		MALI_DEBUG_ASSERT_POINTER(pp_job);
+		MALI_DEBUG_ASSERT_POINTER(pp_job_done);
+		*pp_job_done = pp_job;
+	}
+}
+
+static void mali_executor_change_state_pp_physical(struct mali_group *group,
+		_mali_osk_list_t *old_list,
+		u32 *old_count,
+		_mali_osk_list_t *new_list,
+		u32 *new_count)
+{
+	/*
+	 * It's a bit more complicated to change the state for the physical PP
+	 * groups since their state is determined by the list they are on.
+	 */
+#if defined(DEBUG)
+	mali_bool found = MALI_FALSE;
+	struct mali_group *group_iter;
+	struct mali_group *temp;
+	u32 old_counted = 0;
+	u32 new_counted = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(old_list);
+	MALI_DEBUG_ASSERT_POINTER(old_count);
+	MALI_DEBUG_ASSERT_POINTER(new_list);
+	MALI_DEBUG_ASSERT_POINTER(new_count);
+
+	/*
+	 * Verify that group is present on old list,
+	 * and that the count is correct
+	 */
+
+	_MALI_OSK_LIST_FOREACHENTRY(group_iter, temp, old_list,
+				    struct mali_group, executor_list) {
+		old_counted++;
+		if (group == group_iter) {
+			found = MALI_TRUE;
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(group_iter, temp, new_list,
+				    struct mali_group, executor_list) {
+		new_counted++;
+	}
+
+	if (MALI_FALSE == found) {
+		if (old_list == &group_list_idle) {
+			MALI_DEBUG_PRINT(1, (" old Group list is idle,"));
+		} else if (old_list == &group_list_inactive) {
+			MALI_DEBUG_PRINT(1, (" old Group list is inactive,"));
+		} else if (old_list == &group_list_working) {
+			MALI_DEBUG_PRINT(1, (" old Group list is working,"));
+		} else if (old_list == &group_list_disabled) {
+			MALI_DEBUG_PRINT(1, (" old Group list is disable,"));
+		}
+
+		if (MALI_TRUE == mali_executor_group_is_in_state(group, EXEC_STATE_WORKING)) {
+			MALI_DEBUG_PRINT(1, (" group in working \n"));
+		} else if (MALI_TRUE == mali_executor_group_is_in_state(group, EXEC_STATE_INACTIVE)) {
+			MALI_DEBUG_PRINT(1, (" group in inactive \n"));
+		} else if (MALI_TRUE == mali_executor_group_is_in_state(group, EXEC_STATE_IDLE)) {
+			MALI_DEBUG_PRINT(1, (" group in idle \n"));
+		} else if (MALI_TRUE == mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED)) {
+			MALI_DEBUG_PRINT(1, (" but group in disabled \n"));
+		}
+	}
+
+	MALI_DEBUG_ASSERT(MALI_TRUE == found);
+	MALI_DEBUG_ASSERT(0 < (*old_count));
+	MALI_DEBUG_ASSERT((*old_count) == old_counted);
+	MALI_DEBUG_ASSERT((*new_count) == new_counted);
+#endif
+
+	_mali_osk_list_move(&group->executor_list, new_list);
+	(*old_count)--;
+	(*new_count)++;
+}
+
+static void mali_executor_set_state_pp_physical(struct mali_group *group,
+		_mali_osk_list_t *new_list,
+		u32 *new_count)
+{
+	_mali_osk_list_add(&group->executor_list, new_list);
+	(*new_count)++;
+}
+
+static mali_bool mali_executor_group_is_in_state(struct mali_group *group,
+		enum mali_executor_state_t state)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	if (gp_group == group) {
+		if (gp_group_state == state) {
+			return MALI_TRUE;
+		}
+	} else if (virtual_group == group || mali_group_is_in_virtual(group)) {
+		if (virtual_group_state == state) {
+			return MALI_TRUE;
+		}
+	} else {
+		/* Physical PP group */
+		struct mali_group *group_iter;
+		struct mali_group *temp;
+		_mali_osk_list_t *list;
+
+		if (EXEC_STATE_DISABLED == state) {
+			list = &group_list_disabled;
+		} else if (EXEC_STATE_INACTIVE == state) {
+			list = &group_list_inactive;
+		} else if (EXEC_STATE_IDLE == state) {
+			list = &group_list_idle;
+		} else {
+			MALI_DEBUG_ASSERT(EXEC_STATE_WORKING == state);
+			list = &group_list_working;
+		}
+
+		_MALI_OSK_LIST_FOREACHENTRY(group_iter, temp, list,
+					    struct mali_group, executor_list) {
+			if (group_iter == group) {
+				return MALI_TRUE;
+			}
+		}
+	}
+
+	/* group not in correct state */
+	return MALI_FALSE;
+}
+
+static void mali_executor_group_enable_internal(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED));
+
+	/* Put into inactive state (== "lowest" enabled state) */
+	if (group == gp_group) {
+		MALI_DEBUG_ASSERT(EXEC_STATE_DISABLED == gp_group_state);
+		gp_group_state = EXEC_STATE_INACTIVE;
+	} else {
+		mali_executor_change_state_pp_physical(group,
+						       &group_list_disabled,
+						       &group_list_disabled_count,
+						       &group_list_inactive,
+						       &group_list_inactive_count);
+
+		++num_physical_pp_cores_enabled;
+		MALI_DEBUG_PRINT(4, ("Enabling group id %d \n", group->pp_core->core_id));
+	}
+
+	if (MALI_GROUP_STATE_ACTIVE == mali_group_activate(group)) {
+		MALI_DEBUG_ASSERT(MALI_TRUE == mali_group_power_is_on(group));
+
+		/* Move from inactive to idle */
+		if (group == gp_group) {
+			gp_group_state = EXEC_STATE_IDLE;
+		} else {
+			mali_executor_change_state_pp_physical(group,
+							       &group_list_inactive,
+							       &group_list_inactive_count,
+							       &group_list_idle,
+							       &group_list_idle_count);
+
+			if (mali_executor_has_virtual_group()) {
+				if (mali_executor_physical_rejoin_virtual(group)) {
+					mali_pm_update_async();
+				}
+			}
+		}
+	} else {
+		mali_pm_update_async();
+	}
+}
+
+static void mali_executor_group_disable_internal(struct mali_group *group)
+{
+	mali_bool working;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(!mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED));
+
+	working = mali_executor_group_is_in_state(group, EXEC_STATE_WORKING);
+	if (MALI_TRUE == working) {
+		/** Group to be disabled once it completes current work,
+		 * when virtual group completes, also check child groups for this flag */
+		mali_group_set_disable_request(group, MALI_TRUE);
+		return;
+	}
+
+	/* Put into disabled state */
+	if (group == gp_group) {
+		/* GP group */
+		MALI_DEBUG_ASSERT(EXEC_STATE_WORKING != gp_group_state);
+		gp_group_state = EXEC_STATE_DISABLED;
+	} else {
+		if (mali_group_is_in_virtual(group)) {
+			/* A child group of virtual group. move the specific group from virtual group */
+			MALI_DEBUG_ASSERT(EXEC_STATE_WORKING != virtual_group_state);
+
+			mali_executor_set_state_pp_physical(group,
+							    &group_list_disabled,
+							    &group_list_disabled_count);
+
+			mali_group_remove_group(virtual_group, group);
+			mali_executor_disable_empty_virtual();
+		} else {
+			mali_executor_change_group_status_disabled(group);
+		}
+
+		--num_physical_pp_cores_enabled;
+		MALI_DEBUG_PRINT(4, ("Disabling group id %d \n", group->pp_core->core_id));
+	}
+
+	if (MALI_GROUP_STATE_INACTIVE != group->state) {
+		if (MALI_TRUE == mali_group_deactivate(group)) {
+			mali_pm_update_async();
+		}
+	}
+}
+
+static void mali_executor_notify_core_change(u32 num_cores)
+{
+	mali_bool done = MALI_FALSE;
+
+	if (mali_is_mali450() || mali_is_mali470()) {
+		return;
+	}
+
+	/*
+	 * This function gets a bit complicated because we can't hold the session lock while
+	 * allocating notification objects.
+	 */
+	while (!done) {
+		u32 i;
+		u32 num_sessions_alloc;
+		u32 num_sessions_with_lock;
+		u32 used_notification_objects = 0;
+		_mali_osk_notification_t **notobjs;
+
+		/* Pre allocate the number of notifications objects we need right now (might change after lock has been taken) */
+		num_sessions_alloc = mali_session_get_count();
+		if (0 == num_sessions_alloc) {
+			/* No sessions to report to */
+			return;
+		}
+
+		notobjs = (_mali_osk_notification_t **)_mali_osk_malloc(sizeof(_mali_osk_notification_t *) * num_sessions_alloc);
+		if (NULL == notobjs) {
+			MALI_PRINT_ERROR(("Failed to notify user space session about num PP core change (alloc failure)\n"));
+			/* there is probably no point in trying again, system must be really low on memory and probably unusable now anyway */
+			return;
+		}
+
+		for (i = 0; i < num_sessions_alloc; i++) {
+			notobjs[i] = _mali_osk_notification_create(_MALI_NOTIFICATION_PP_NUM_CORE_CHANGE, sizeof(_mali_uk_pp_num_cores_changed_s));
+			if (NULL != notobjs[i]) {
+				_mali_uk_pp_num_cores_changed_s *data = notobjs[i]->result_buffer;
+				data->number_of_enabled_cores = num_cores;
+			} else {
+				MALI_PRINT_ERROR(("Failed to notify user space session about num PP core change (alloc failure %u)\n", i));
+			}
+		}
+
+		mali_session_lock();
+
+		/* number of sessions will not change while we hold the lock */
+		num_sessions_with_lock = mali_session_get_count();
+
+		if (num_sessions_alloc >= num_sessions_with_lock) {
+			/* We have allocated enough notification objects for all the sessions atm */
+			struct mali_session_data *session, *tmp;
+			MALI_SESSION_FOREACH(session, tmp, link) {
+				MALI_DEBUG_ASSERT(used_notification_objects < num_sessions_alloc);
+				if (NULL != notobjs[used_notification_objects]) {
+					mali_session_send_notification(session, notobjs[used_notification_objects]);
+					notobjs[used_notification_objects] = NULL; /* Don't track this notification object any more */
+				}
+				used_notification_objects++;
+			}
+			done = MALI_TRUE;
+		}
+
+		mali_session_unlock();
+
+		/* Delete any remaining/unused notification objects */
+		for (; used_notification_objects < num_sessions_alloc; used_notification_objects++) {
+			if (NULL != notobjs[used_notification_objects]) {
+				_mali_osk_notification_delete(notobjs[used_notification_objects]);
+			}
+		}
+
+		_mali_osk_free(notobjs);
+	}
+}
+
+static mali_bool mali_executor_core_scaling_is_done(void *data)
+{
+	u32 i;
+	u32 num_groups;
+	mali_bool ret = MALI_TRUE;
+
+	MALI_IGNORE(data);
+
+	mali_executor_lock();
+
+	num_groups = mali_group_get_glob_num_groups();
+
+	for (i = 0; i < num_groups; i++) {
+		struct mali_group *group = mali_group_get_glob_group(i);
+
+		if (NULL != group) {
+			if (MALI_TRUE == group->disable_requested && NULL != mali_group_get_pp_core(group)) {
+				ret = MALI_FALSE;
+				break;
+			}
+		}
+	}
+	mali_executor_unlock();
+
+	return ret;
+}
+
+static void mali_executor_wq_notify_core_change(void *arg)
+{
+	MALI_IGNORE(arg);
+
+	if (mali_is_mali450() || mali_is_mali470()) {
+		return;
+	}
+
+	_mali_osk_wait_queue_wait_event(executor_notify_core_change_wait_queue,
+					mali_executor_core_scaling_is_done, NULL);
+
+	mali_executor_notify_core_change(num_physical_pp_cores_enabled);
+}
+
+/**
+ * Clear all disable request from the _last_ core scaling behavior.
+ */
+static void mali_executor_core_scaling_reset(void)
+{
+	u32 i;
+	u32 num_groups;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	num_groups = mali_group_get_glob_num_groups();
+
+	for (i = 0; i < num_groups; i++) {
+		struct mali_group *group = mali_group_get_glob_group(i);
+
+		if (NULL != group) {
+			group->disable_requested = MALI_FALSE;
+		}
+	}
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		core_scaling_delay_up_mask[i] = 0;
+	}
+}
+
+static void mali_executor_core_scale(unsigned int target_core_nr)
+{
+	int current_core_scaling_mask[MALI_MAX_NUMBER_OF_DOMAINS] = { 0 };
+	int target_core_scaling_mask[MALI_MAX_NUMBER_OF_DOMAINS] = { 0 };
+	int i;
+
+	MALI_DEBUG_ASSERT(0 < target_core_nr);
+	MALI_DEBUG_ASSERT(num_physical_pp_cores_total >= target_core_nr);
+
+	mali_executor_lock();
+
+	if (target_core_nr < num_physical_pp_cores_enabled) {
+		MALI_DEBUG_PRINT(2, ("Requesting %d cores: disabling %d cores\n", target_core_nr, num_physical_pp_cores_enabled - target_core_nr));
+	} else {
+		MALI_DEBUG_PRINT(2, ("Requesting %d cores: enabling %d cores\n", target_core_nr, target_core_nr - num_physical_pp_cores_enabled));
+	}
+
+	/* When a new core scaling request is comming,  we should remove the un-doing
+	 * part of the last core scaling request.  It's safe because we have only one
+	 * lock(executor lock) protection. */
+	mali_executor_core_scaling_reset();
+
+	mali_pm_get_best_power_cost_mask(num_physical_pp_cores_enabled, current_core_scaling_mask);
+	mali_pm_get_best_power_cost_mask(target_core_nr, target_core_scaling_mask);
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		target_core_scaling_mask[i] = target_core_scaling_mask[i] - current_core_scaling_mask[i];
+		MALI_DEBUG_PRINT(5, ("target_core_scaling_mask[%d] = %d\n", i, target_core_scaling_mask[i]));
+	}
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		if (0 > target_core_scaling_mask[i]) {
+			struct mali_pm_domain *domain;
+
+			domain = mali_pm_domain_get_from_index(i);
+
+			/* Domain is valid and has pp cores */
+			if ((NULL != domain) && !(_mali_osk_list_empty(&domain->group_list))) {
+				struct mali_group *group;
+				struct mali_group *temp;
+
+				_MALI_OSK_LIST_FOREACHENTRY(group, temp, &domain->group_list, struct mali_group, pm_domain_list) {
+					if (NULL != mali_group_get_pp_core(group) && (!mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED))
+					    && (!mali_group_is_virtual(group))) {
+						mali_executor_group_disable_internal(group);
+						target_core_scaling_mask[i]++;
+						if ((0 == target_core_scaling_mask[i])) {
+							break;
+						}
+
+					}
+				}
+			}
+		}
+	}
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		/**
+		 * Target_core_scaling_mask[i] is bigger than 0,
+		 * means we need to enable some pp cores in
+		 * this domain whose domain index is i.
+		 */
+		if (0 < target_core_scaling_mask[i]) {
+			struct mali_pm_domain *domain;
+
+			if (num_physical_pp_cores_enabled >= target_core_nr) {
+				break;
+			}
+
+			domain = mali_pm_domain_get_from_index(i);
+
+			/* Domain is valid and has pp cores */
+			if ((NULL != domain) && !(_mali_osk_list_empty(&domain->group_list))) {
+				struct mali_group *group;
+				struct mali_group *temp;
+
+				_MALI_OSK_LIST_FOREACHENTRY(group, temp, &domain->group_list, struct mali_group, pm_domain_list) {
+					if (NULL != mali_group_get_pp_core(group) && mali_executor_group_is_in_state(group, EXEC_STATE_DISABLED)
+					    && (!mali_group_is_virtual(group))) {
+						mali_executor_group_enable_internal(group);
+						target_core_scaling_mask[i]--;
+
+						if ((0 == target_core_scaling_mask[i]) || num_physical_pp_cores_enabled == target_core_nr) {
+							break;
+						}
+					}
+				}
+			}
+		}
+	}
+
+	/**
+	 * Here, we may still have some pp cores not been enabled because of some
+	 * pp cores need to be disabled are still in working state.
+	 */
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		if (0 < target_core_scaling_mask[i]) {
+			core_scaling_delay_up_mask[i] = target_core_scaling_mask[i];
+		}
+	}
+
+	mali_executor_schedule();
+	mali_executor_unlock();
+}
+
+static void mali_executor_core_scale_in_group_complete(struct mali_group *group)
+{
+	int num_pp_cores_disabled = 0;
+	int num_pp_cores_to_enable = 0;
+	int i;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(MALI_TRUE == mali_group_disable_requested(group));
+
+	/* Disable child group of virtual group */
+	if (mali_group_is_virtual(group)) {
+		struct mali_group *child;
+		struct mali_group *temp;
+
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+			if (MALI_TRUE == mali_group_disable_requested(child)) {
+				mali_group_set_disable_request(child, MALI_FALSE);
+				mali_executor_group_disable_internal(child);
+				num_pp_cores_disabled++;
+			}
+		}
+		mali_group_set_disable_request(group, MALI_FALSE);
+	} else {
+		mali_executor_group_disable_internal(group);
+		mali_group_set_disable_request(group, MALI_FALSE);
+		if (NULL != mali_group_get_pp_core(group)) {
+			num_pp_cores_disabled++;
+		}
+	}
+
+	num_pp_cores_to_enable = num_pp_cores_disabled;
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		if (0 < core_scaling_delay_up_mask[i]) {
+			struct mali_pm_domain *domain;
+
+			if (0 == num_pp_cores_to_enable) {
+				break;
+			}
+
+			domain = mali_pm_domain_get_from_index(i);
+
+			/* Domain is valid and has pp cores */
+			if ((NULL != domain) && !(_mali_osk_list_empty(&domain->group_list))) {
+				struct mali_group *disabled_group;
+				struct mali_group *temp;
+
+				_MALI_OSK_LIST_FOREACHENTRY(disabled_group, temp, &domain->group_list, struct mali_group, pm_domain_list) {
+					if (NULL != mali_group_get_pp_core(disabled_group) && mali_executor_group_is_in_state(disabled_group, EXEC_STATE_DISABLED)) {
+						mali_executor_group_enable_internal(disabled_group);
+						core_scaling_delay_up_mask[i]--;
+						num_pp_cores_to_enable--;
+
+						if ((0 == core_scaling_delay_up_mask[i]) || 0 == num_pp_cores_to_enable) {
+							break;
+						}
+					}
+				}
+			}
+		}
+	}
+
+	_mali_osk_wait_queue_wake_up(executor_notify_core_change_wait_queue);
+}
+
+static void mali_executor_change_group_status_disabled(struct mali_group *group)
+{
+	/* Physical PP group */
+	mali_bool idle;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	idle = mali_executor_group_is_in_state(group, EXEC_STATE_IDLE);
+	if (MALI_TRUE == idle) {
+		mali_executor_change_state_pp_physical(group,
+						       &group_list_idle,
+						       &group_list_idle_count,
+						       &group_list_disabled,
+						       &group_list_disabled_count);
+	} else {
+		mali_executor_change_state_pp_physical(group,
+						       &group_list_inactive,
+						       &group_list_inactive_count,
+						       &group_list_disabled,
+						       &group_list_disabled_count);
+	}
+}
+
+static mali_bool mali_executor_deactivate_list_idle(mali_bool deactivate_idle_group)
+{
+	mali_bool trigger_pm_update = MALI_FALSE;
+
+	if (group_list_idle_count > 0) {
+		if (mali_executor_has_virtual_group()) {
+
+			/* Rejoin virtual group on Mali-450 */
+
+			struct mali_group *group;
+			struct mali_group *temp;
+
+			_MALI_OSK_LIST_FOREACHENTRY(group, temp,
+						    &group_list_idle,
+						    struct mali_group, executor_list) {
+				if (mali_executor_physical_rejoin_virtual(
+					    group)) {
+					trigger_pm_update = MALI_TRUE;
+				}
+			}
+		} else if (deactivate_idle_group) {
+			struct mali_group *group;
+			struct mali_group *temp;
+
+			/* Deactivate group on Mali-300/400 */
+
+			_MALI_OSK_LIST_FOREACHENTRY(group, temp,
+						    &group_list_idle,
+						    struct mali_group, executor_list) {
+				if (mali_group_deactivate(group)) {
+					trigger_pm_update = MALI_TRUE;
+				}
+
+				/* Move from idle to inactive */
+				mali_executor_change_state_pp_physical(group,
+								       &group_list_idle,
+								       &group_list_idle_count,
+								       &group_list_inactive,
+								       &group_list_inactive_count);
+			}
+		}
+	}
+
+	return trigger_pm_update;
+}
+
+void mali_executor_running_status_print(void)
+{
+	struct mali_group *group = NULL;
+	struct mali_group *temp = NULL;
+
+	MALI_PRINT(("GP running job: %p\n", gp_group->gp_running_job));
+	if ((gp_group->gp_core) && (gp_group->is_working)) {
+		mali_group_dump_status(gp_group);
+	}
+	MALI_PRINT(("Physical PP groups in WORKING state (count = %u):\n", group_list_working_count));
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_working, struct mali_group, executor_list) {
+		MALI_PRINT(("PP running job: %p, subjob %d \n", group->pp_running_job, group->pp_running_sub_job));
+		mali_group_dump_status(group);
+	}
+	MALI_PRINT(("Physical PP groups in INACTIVE state (count = %u):\n", group_list_inactive_count));
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_inactive, struct mali_group, executor_list) {
+		MALI_PRINT(("\tPP status %d, SW power: %s\n", group->state, group->power_is_on ? "On" : "Off"));
+		MALI_PRINT(("\tPP #%d: %s\n", group->pp_core->core_id, group->pp_core->hw_core.description));
+	}
+	MALI_PRINT(("Physical PP groups in IDLE state (count = %u):\n", group_list_idle_count));
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_idle, struct mali_group, executor_list) {
+		MALI_PRINT(("\tPP status %d, SW power: %s\n", group->state, group->power_is_on ? "On" : "Off"));
+		MALI_PRINT(("\tPP #%d: %s\n", group->pp_core->core_id, group->pp_core->hw_core.description));
+	}
+	MALI_PRINT(("Physical PP groups in DISABLED state (count = %u):\n", group_list_disabled_count));
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &group_list_disabled, struct mali_group, executor_list) {
+		MALI_PRINT(("\tPP status %d, SW power: %s\n", group->state, group->power_is_on ? "On" : "Off"));
+		MALI_PRINT(("\tPP #%d: %s\n", group->pp_core->core_id, group->pp_core->hw_core.description));
+	}
+
+	if (mali_executor_has_virtual_group()) {
+		MALI_PRINT(("Virtual group running job: %p\n", virtual_group->pp_running_job));
+		MALI_PRINT(("Virtual group status: %d\n", virtual_group_state));
+		MALI_PRINT(("Virtual group->status: %d\n", virtual_group->state));
+		MALI_PRINT(("\tSW power: %s\n", virtual_group->power_is_on ? "On" : "Off"));
+		_MALI_OSK_LIST_FOREACHENTRY(group, temp, &virtual_group->group_list,
+					    struct mali_group, group_list) {
+			int i = 0;
+			MALI_PRINT(("\tchild group(%s) running job: %p\n", group->pp_core->hw_core.description, group->pp_running_job));
+			MALI_PRINT(("\tchild group(%s)->status: %d\n", group->pp_core->hw_core.description, group->state));
+			MALI_PRINT(("\tchild group(%s) SW power: %s\n", group->pp_core->hw_core.description, group->power_is_on ? "On" : "Off"));
+			if (group->pm_domain) {
+				MALI_PRINT(("\tPower domain: id %u\n", mali_pm_domain_get_id(group->pm_domain)));
+				MALI_PRINT(("\tMask:0x%04x \n", mali_pm_domain_get_mask(group->pm_domain)));
+				MALI_PRINT(("\tUse-count:%u \n", mali_pm_domain_get_use_count(group->pm_domain)));
+				MALI_PRINT(("\tCurrent power status:%s \n", (mali_pm_domain_get_mask(group->pm_domain)& mali_pm_get_current_mask()) ? "On" : "Off"));
+				MALI_PRINT(("\tWanted  power status:%s \n", (mali_pm_domain_get_mask(group->pm_domain)& mali_pm_get_wanted_mask()) ? "On" : "Off"));
+			}
+
+			for (i = 0; i < 2; i++) {
+				if (NULL != group->l2_cache_core[i]) {
+					struct mali_pm_domain *domain;
+					domain = mali_l2_cache_get_pm_domain(group->l2_cache_core[i]);
+					MALI_PRINT(("\t L2(index %d) group SW power: %s\n", i, group->l2_cache_core[i]->power_is_on ? "On" : "Off"));
+					if (domain) {
+						MALI_PRINT(("\tL2 Power domain: id %u\n", mali_pm_domain_get_id(domain)));
+						MALI_PRINT(("\tL2 Mask:0x%04x \n", mali_pm_domain_get_mask(domain)));
+						MALI_PRINT(("\tL2 Use-count:%u \n", mali_pm_domain_get_use_count(domain)));
+						MALI_PRINT(("\tL2 Current power status:%s \n", (mali_pm_domain_get_mask(domain) & mali_pm_get_current_mask()) ? "On" : "Off"));
+						MALI_PRINT(("\tL2 Wanted  power status:%s \n", (mali_pm_domain_get_mask(domain) & mali_pm_get_wanted_mask()) ? "On" : "Off"));
+					}
+				}
+			}
+		}
+		if (EXEC_STATE_WORKING == virtual_group_state) {
+			mali_group_dump_status(virtual_group);
+		}
+	}
+}
+
+void mali_executor_status_dump(void)
+{
+	mali_executor_lock();
+	mali_scheduler_lock();
+
+	/* print schedule queue status */
+	mali_scheduler_gp_pp_job_queue_print();
+
+	mali_scheduler_unlock();
+	mali_executor_unlock();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_executor.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_executor.h
@@ -0,0 +1,102 @@
+/*
+ * Copyright (C) 2012, 2014-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_EXECUTOR_H__
+#define __MALI_EXECUTOR_H__
+
+#include "mali_osk.h"
+#include "mali_scheduler_types.h"
+#include "mali_kernel_common.h"
+
+typedef enum {
+	MALI_EXECUTOR_HINT_GP_BOUND = 0
+#define MALI_EXECUTOR_HINT_MAX        1
+} mali_executor_hint;
+
+extern mali_bool mali_executor_hints[MALI_EXECUTOR_HINT_MAX];
+
+/* forward declare struct instead of using include */
+struct mali_session_data;
+struct mali_group;
+struct mali_pp_core;
+
+extern _mali_osk_spinlock_irq_t *mali_executor_lock_obj;
+
+#define MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD() MALI_DEBUG_ASSERT_LOCK_HELD(mali_executor_lock_obj);
+
+_mali_osk_errcode_t mali_executor_initialize(void);
+void mali_executor_terminate(void);
+
+void mali_executor_populate(void);
+void mali_executor_depopulate(void);
+
+void mali_executor_suspend(void);
+void mali_executor_resume(void);
+
+u32 mali_executor_get_num_cores_total(void);
+u32 mali_executor_get_num_cores_enabled(void);
+struct mali_pp_core *mali_executor_get_virtual_pp(void);
+struct mali_group *mali_executor_get_virtual_group(void);
+
+void mali_executor_zap_all_active(struct mali_session_data *session);
+
+/**
+ * Schedule GP and PP according to bitmask.
+ *
+ * @param mask A scheduling bitmask.
+ * @param deferred_schedule MALI_TRUE if schedule should be deferred, MALI_FALSE if not.
+ */
+void mali_executor_schedule_from_mask(mali_scheduler_mask mask, mali_bool deferred_schedule);
+
+_mali_osk_errcode_t mali_executor_interrupt_gp(struct mali_group *group, mali_bool in_upper_half);
+_mali_osk_errcode_t mali_executor_interrupt_pp(struct mali_group *group, mali_bool in_upper_half);
+_mali_osk_errcode_t mali_executor_interrupt_mmu(struct mali_group *group, mali_bool in_upper_half);
+void mali_executor_group_power_up(struct mali_group *groups[], u32 num_groups);
+void mali_executor_group_power_down(struct mali_group *groups[], u32 num_groups);
+
+void mali_executor_abort_session(struct mali_session_data *session);
+
+void mali_executor_core_scaling_enable(void);
+void mali_executor_core_scaling_disable(void);
+mali_bool mali_executor_core_scaling_is_enabled(void);
+
+void mali_executor_group_enable(struct mali_group *group);
+void mali_executor_group_disable(struct mali_group *group);
+mali_bool mali_executor_group_is_disabled(struct mali_group *group);
+
+int mali_executor_set_perf_level(unsigned int target_core_nr, mali_bool override);
+
+#if MALI_STATE_TRACKING
+u32 mali_executor_dump_state(char *buf, u32 size);
+#endif
+
+MALI_STATIC_INLINE void mali_executor_hint_enable(mali_executor_hint hint)
+{
+	MALI_DEBUG_ASSERT(hint < MALI_EXECUTOR_HINT_MAX);
+	mali_executor_hints[hint] = MALI_TRUE;
+}
+
+MALI_STATIC_INLINE void mali_executor_hint_disable(mali_executor_hint hint)
+{
+	MALI_DEBUG_ASSERT(hint < MALI_EXECUTOR_HINT_MAX);
+	mali_executor_hints[hint] = MALI_FALSE;
+}
+
+MALI_STATIC_INLINE mali_bool mali_executor_hint_is_enabled(mali_executor_hint hint)
+{
+	MALI_DEBUG_ASSERT(hint < MALI_EXECUTOR_HINT_MAX);
+	return mali_executor_hints[hint];
+}
+
+void mali_executor_running_status_print(void);
+void mali_executor_status_dump(void);
+void mali_executor_lock(void);
+void mali_executor_unlock(void);
+#endif /* __MALI_EXECUTOR_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_gp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_gp.c
@@ -0,0 +1,357 @@
+/*
+ * Copyright (C) 2011-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_gp.h"
+#include "mali_hw_core.h"
+#include "mali_group.h"
+#include "mali_osk.h"
+#include "regs/mali_gp_regs.h"
+#include "mali_kernel_common.h"
+#include "mali_kernel_core.h"
+#if defined(CONFIG_MALI400_PROFILING)
+#include "mali_osk_profiling.h"
+#endif
+
+static struct mali_gp_core *mali_global_gp_core = NULL;
+
+/* Interrupt handlers */
+static void mali_gp_irq_probe_trigger(void *data);
+static _mali_osk_errcode_t mali_gp_irq_probe_ack(void *data);
+
+struct mali_gp_core *mali_gp_create(const _mali_osk_resource_t *resource, struct mali_group *group)
+{
+	struct mali_gp_core *core = NULL;
+
+	MALI_DEBUG_ASSERT(NULL == mali_global_gp_core);
+	MALI_DEBUG_PRINT(2, ("Mali GP: Creating Mali GP core: %s\n", resource->description));
+
+	core = _mali_osk_malloc(sizeof(struct mali_gp_core));
+	if (NULL != core) {
+		if (_MALI_OSK_ERR_OK == mali_hw_core_create(&core->hw_core, resource, MALIGP2_REGISTER_ADDRESS_SPACE_SIZE)) {
+			_mali_osk_errcode_t ret;
+
+			ret = mali_gp_reset(core);
+
+			if (_MALI_OSK_ERR_OK == ret) {
+				ret = mali_group_add_gp_core(group, core);
+				if (_MALI_OSK_ERR_OK == ret) {
+					/* Setup IRQ handlers (which will do IRQ probing if needed) */
+					core->irq = _mali_osk_irq_init(resource->irq,
+								       mali_group_upper_half_gp,
+								       group,
+								       mali_gp_irq_probe_trigger,
+								       mali_gp_irq_probe_ack,
+								       core,
+								       resource->description);
+					if (NULL != core->irq) {
+						MALI_DEBUG_PRINT(4, ("Mali GP: set global gp core from 0x%08X to 0x%08X\n", mali_global_gp_core, core));
+						mali_global_gp_core = core;
+
+						return core;
+					} else {
+						MALI_PRINT_ERROR(("Mali GP: Failed to setup interrupt handlers for GP core %s\n", core->hw_core.description));
+					}
+					mali_group_remove_gp_core(group);
+				} else {
+					MALI_PRINT_ERROR(("Mali GP: Failed to add core %s to group\n", core->hw_core.description));
+				}
+			}
+			mali_hw_core_delete(&core->hw_core);
+		}
+
+		_mali_osk_free(core);
+	} else {
+		MALI_PRINT_ERROR(("Failed to allocate memory for GP core\n"));
+	}
+
+	return NULL;
+}
+
+void mali_gp_delete(struct mali_gp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	_mali_osk_irq_term(core->irq);
+	mali_hw_core_delete(&core->hw_core);
+	mali_global_gp_core = NULL;
+	_mali_osk_free(core);
+}
+
+void mali_gp_stop_bus(struct mali_gp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_CMD, MALIGP2_REG_VAL_CMD_STOP_BUS);
+}
+
+_mali_osk_errcode_t mali_gp_stop_bus_wait(struct mali_gp_core *core)
+{
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	/* Send the stop bus command. */
+	mali_gp_stop_bus(core);
+
+	/* Wait for bus to be stopped */
+	for (i = 0; i < MALI_REG_POLL_COUNT_SLOW; i++) {
+		if (mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_STATUS) & MALIGP2_REG_VAL_STATUS_BUS_STOPPED) {
+			break;
+		}
+	}
+
+	if (MALI_REG_POLL_COUNT_SLOW == i) {
+		MALI_PRINT_ERROR(("Mali GP: Failed to stop bus on %s\n", core->hw_core.description));
+		return _MALI_OSK_ERR_FAULT;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_gp_hard_reset(struct mali_gp_core *core)
+{
+	const u32 reset_wait_target_register = MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_LIMIT;
+	const u32 reset_invalid_value = 0xC0FFE000;
+	const u32 reset_check_value = 0xC01A0000;
+	const u32 reset_default_value = 0;
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+	MALI_DEBUG_PRINT(4, ("Mali GP: Hard reset of core %s\n", core->hw_core.description));
+
+	mali_hw_core_register_write(&core->hw_core, reset_wait_target_register, reset_invalid_value);
+
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_CMD, MALIGP2_REG_VAL_CMD_RESET);
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; i++) {
+		mali_hw_core_register_write(&core->hw_core, reset_wait_target_register, reset_check_value);
+		if (reset_check_value == mali_hw_core_register_read(&core->hw_core, reset_wait_target_register)) {
+			break;
+		}
+	}
+
+	if (MALI_REG_POLL_COUNT_FAST == i) {
+		MALI_PRINT_ERROR(("Mali GP: The hard reset loop didn't work, unable to recover\n"));
+	}
+
+	mali_hw_core_register_write(&core->hw_core, reset_wait_target_register, reset_default_value); /* set it back to the default */
+	/* Re-enable interrupts */
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_CLEAR, MALIGP2_REG_VAL_IRQ_MASK_ALL);
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_MASK, MALIGP2_REG_VAL_IRQ_MASK_USED);
+
+}
+
+void mali_gp_reset_async(struct mali_gp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	MALI_DEBUG_PRINT(4, ("Mali GP: Reset of core %s\n", core->hw_core.description));
+
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_MASK, 0); /* disable the IRQs */
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_CLEAR, MALI400GP_REG_VAL_IRQ_RESET_COMPLETED);
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_CMD, MALI400GP_REG_VAL_CMD_SOFT_RESET);
+
+}
+
+_mali_osk_errcode_t mali_gp_reset_wait(struct mali_gp_core *core)
+{
+	int i;
+	u32 rawstat = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; i++) {
+		rawstat = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_RAWSTAT);
+		if (rawstat & MALI400GP_REG_VAL_IRQ_RESET_COMPLETED) {
+			break;
+		}
+	}
+
+	if (i == MALI_REG_POLL_COUNT_FAST) {
+		MALI_PRINT_ERROR(("Mali GP: Failed to reset core %s, rawstat: 0x%08x\n",
+				  core->hw_core.description, rawstat));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Re-enable interrupts */
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_CLEAR, MALIGP2_REG_VAL_IRQ_MASK_ALL);
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_MASK, MALIGP2_REG_VAL_IRQ_MASK_USED);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_gp_reset(struct mali_gp_core *core)
+{
+	mali_gp_reset_async(core);
+	return mali_gp_reset_wait(core);
+}
+
+void mali_gp_job_start(struct mali_gp_core *core, struct mali_gp_job *job)
+{
+	u32 startcmd = 0;
+	u32 *frame_registers = mali_gp_job_get_frame_registers(job);
+	u32 counter_src0 = mali_gp_job_get_perf_counter_src0(job);
+	u32 counter_src1 = mali_gp_job_get_perf_counter_src1(job);
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	if (mali_gp_job_has_vs_job(job)) {
+		startcmd |= (u32) MALIGP2_REG_VAL_CMD_START_VS;
+	}
+
+	if (mali_gp_job_has_plbu_job(job)) {
+		startcmd |= (u32) MALIGP2_REG_VAL_CMD_START_PLBU;
+	}
+
+	MALI_DEBUG_ASSERT(0 != startcmd);
+
+	mali_hw_core_register_write_array_relaxed(&core->hw_core, MALIGP2_REG_ADDR_MGMT_VSCL_START_ADDR, frame_registers, MALIGP2_NUM_REGS_FRAME);
+
+	if (MALI_HW_CORE_NO_COUNTER != counter_src0) {
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_SRC, counter_src0);
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_ENABLE, MALIGP2_REG_VAL_PERF_CNT_ENABLE);
+	}
+	if (MALI_HW_CORE_NO_COUNTER != counter_src1) {
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PERF_CNT_1_SRC, counter_src1);
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PERF_CNT_1_ENABLE, MALIGP2_REG_VAL_PERF_CNT_ENABLE);
+	}
+
+	MALI_DEBUG_PRINT(3, ("Mali GP: Starting job (0x%08x) on core %s with command 0x%08X\n", job, core->hw_core.description, startcmd));
+
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALIGP2_REG_ADDR_MGMT_CMD, MALIGP2_REG_VAL_CMD_UPDATE_PLBU_ALLOC);
+
+	/* Barrier to make sure the previous register write is finished */
+	_mali_osk_write_mem_barrier();
+
+	/* This is the command that starts the core.
+	 *
+	 * Don't actually run the job if PROFILING_SKIP_PP_JOBS are set, just
+	 * force core to assert the completion interrupt.
+	 */
+#if !defined(PROFILING_SKIP_GP_JOBS)
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALIGP2_REG_ADDR_MGMT_CMD, startcmd);
+#else
+	{
+		u32 bits = 0;
+
+		if (mali_gp_job_has_vs_job(job))
+			bits = MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST;
+		if (mali_gp_job_has_plbu_job(job))
+			bits |= MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST;
+
+		mali_hw_core_register_write_relaxed(&core->hw_core,
+						    MALIGP2_REG_ADDR_MGMT_INT_RAWSTAT, bits);
+	}
+#endif
+
+	/* Barrier to make sure the previous register write is finished */
+	_mali_osk_write_mem_barrier();
+}
+
+void mali_gp_resume_with_new_heap(struct mali_gp_core *core, u32 start_addr, u32 end_addr)
+{
+	u32 irq_readout;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	irq_readout = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_RAWSTAT);
+
+	if (irq_readout & MALIGP2_REG_VAL_IRQ_PLBU_OUT_OF_MEM) {
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_CLEAR, (MALIGP2_REG_VAL_IRQ_PLBU_OUT_OF_MEM | MALIGP2_REG_VAL_IRQ_HANG));
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_MASK, MALIGP2_REG_VAL_IRQ_MASK_USED); /* re-enable interrupts */
+		mali_hw_core_register_write_relaxed(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PLBU_ALLOC_START_ADDR, start_addr);
+		mali_hw_core_register_write_relaxed(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PLBU_ALLOC_END_ADDR, end_addr);
+
+		MALI_DEBUG_PRINT(3, ("Mali GP: Resuming job\n"));
+
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_CMD, MALIGP2_REG_VAL_CMD_UPDATE_PLBU_ALLOC);
+		_mali_osk_write_mem_barrier();
+	}
+	/*
+	 * else: core has been reset between PLBU_OUT_OF_MEM interrupt and this new heap response.
+	 * A timeout or a page fault on Mali-200 PP core can cause this behaviour.
+	 */
+}
+
+u32 mali_gp_core_get_version(struct mali_gp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	return mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_VERSION);
+}
+
+struct mali_gp_core *mali_gp_get_global_gp_core(void)
+{
+	return mali_global_gp_core;
+}
+
+/* ------------- interrupt handling below ------------------ */
+static void mali_gp_irq_probe_trigger(void *data)
+{
+	struct mali_gp_core *core = (struct mali_gp_core *)data;
+
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_MASK, MALIGP2_REG_VAL_IRQ_MASK_USED);
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_RAWSTAT, MALIGP2_REG_VAL_IRQ_AXI_BUS_ERROR);
+	_mali_osk_mem_barrier();
+}
+
+static _mali_osk_errcode_t mali_gp_irq_probe_ack(void *data)
+{
+	struct mali_gp_core *core = (struct mali_gp_core *)data;
+	u32 irq_readout;
+
+	irq_readout = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_STAT);
+	if (MALIGP2_REG_VAL_IRQ_AXI_BUS_ERROR & irq_readout) {
+		mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_CLEAR, MALIGP2_REG_VAL_IRQ_AXI_BUS_ERROR);
+		_mali_osk_mem_barrier();
+		return _MALI_OSK_ERR_OK;
+	}
+
+	return _MALI_OSK_ERR_FAULT;
+}
+
+/* ------ local helper functions below --------- */
+#if MALI_STATE_TRACKING
+u32 mali_gp_dump_state(struct mali_gp_core *core, char *buf, u32 size)
+{
+	int n = 0;
+
+	n += _mali_osk_snprintf(buf + n, size - n, "\tGP: %s\n", core->hw_core.description);
+
+	return n;
+}
+#endif
+
+void mali_gp_update_performance_counters(struct mali_gp_core *core, struct mali_gp_job *job)
+{
+	u32 val0 = 0;
+	u32 val1 = 0;
+	u32 counter_src0 = mali_gp_job_get_perf_counter_src0(job);
+	u32 counter_src1 = mali_gp_job_get_perf_counter_src1(job);
+
+	if (MALI_HW_CORE_NO_COUNTER != counter_src0) {
+		val0 = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_VALUE);
+		mali_gp_job_set_perf_counter_value0(job, val0);
+
+#if defined(CONFIG_MALI400_PROFILING)
+		_mali_osk_profiling_report_hw_counter(COUNTER_VP_0_C0, val0);
+		_mali_osk_profiling_record_global_counters(COUNTER_VP_0_C0, val0);
+#endif
+
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER != counter_src1) {
+		val1 = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PERF_CNT_1_VALUE);
+		mali_gp_job_set_perf_counter_value1(job, val1);
+
+#if defined(CONFIG_MALI400_PROFILING)
+		_mali_osk_profiling_report_hw_counter(COUNTER_VP_0_C1, val1);
+		_mali_osk_profiling_record_global_counters(COUNTER_VP_0_C1, val1);
+#endif
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_gp.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_gp.h
@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2011-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_GP_H__
+#define __MALI_GP_H__
+
+#include "mali_osk.h"
+#include "mali_gp_job.h"
+#include "mali_hw_core.h"
+#include "regs/mali_gp_regs.h"
+
+struct mali_group;
+
+/**
+ * Definition of the GP core struct
+ * Used to track a GP core in the system.
+ */
+struct mali_gp_core {
+	struct mali_hw_core  hw_core;           /**< Common for all HW cores */
+	_mali_osk_irq_t     *irq;               /**< IRQ handler */
+};
+
+_mali_osk_errcode_t mali_gp_initialize(void);
+void mali_gp_terminate(void);
+
+struct mali_gp_core *mali_gp_create(const _mali_osk_resource_t *resource, struct mali_group *group);
+void mali_gp_delete(struct mali_gp_core *core);
+
+void mali_gp_stop_bus(struct mali_gp_core *core);
+_mali_osk_errcode_t mali_gp_stop_bus_wait(struct mali_gp_core *core);
+void mali_gp_reset_async(struct mali_gp_core *core);
+_mali_osk_errcode_t mali_gp_reset_wait(struct mali_gp_core *core);
+void mali_gp_hard_reset(struct mali_gp_core *core);
+_mali_osk_errcode_t mali_gp_reset(struct mali_gp_core *core);
+
+void mali_gp_job_start(struct mali_gp_core *core, struct mali_gp_job *job);
+void mali_gp_resume_with_new_heap(struct mali_gp_core *core, u32 start_addr, u32 end_addr);
+
+u32 mali_gp_core_get_version(struct mali_gp_core *core);
+
+struct mali_gp_core *mali_gp_get_global_gp_core(void);
+
+#if MALI_STATE_TRACKING
+u32 mali_gp_dump_state(struct mali_gp_core *core, char *buf, u32 size);
+#endif
+
+void mali_gp_update_performance_counters(struct mali_gp_core *core, struct mali_gp_job *job);
+
+MALI_STATIC_INLINE const char *mali_gp_core_description(struct mali_gp_core *core)
+{
+	return core->hw_core.description;
+}
+
+MALI_STATIC_INLINE enum mali_interrupt_result mali_gp_get_interrupt_result(struct mali_gp_core *core)
+{
+	u32 stat_used = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_STAT) &
+			MALIGP2_REG_VAL_IRQ_MASK_USED;
+
+	if (0 == stat_used) {
+		return MALI_INTERRUPT_RESULT_NONE;
+	} else if ((MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST |
+		    MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST) == stat_used) {
+		return MALI_INTERRUPT_RESULT_SUCCESS;
+	} else if (MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST == stat_used) {
+		return MALI_INTERRUPT_RESULT_SUCCESS_VS;
+	} else if (MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST == stat_used) {
+		return MALI_INTERRUPT_RESULT_SUCCESS_PLBU;
+	} else if (MALIGP2_REG_VAL_IRQ_PLBU_OUT_OF_MEM & stat_used) {
+		return MALI_INTERRUPT_RESULT_OOM;
+	}
+
+	return MALI_INTERRUPT_RESULT_ERROR;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_get_rawstat(struct mali_gp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	return mali_hw_core_register_read(&core->hw_core,
+					  MALIGP2_REG_ADDR_MGMT_INT_RAWSTAT);
+}
+
+MALI_STATIC_INLINE u32 mali_gp_is_active(struct mali_gp_core *core)
+{
+	u32 status = mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_STATUS);
+	return (status & MALIGP2_REG_VAL_STATUS_MASK_ACTIVE) ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE void mali_gp_mask_all_interrupts(struct mali_gp_core *core)
+{
+	mali_hw_core_register_write(&core->hw_core, MALIGP2_REG_ADDR_MGMT_INT_MASK, MALIGP2_REG_VAL_IRQ_MASK_NONE);
+}
+
+MALI_STATIC_INLINE void mali_gp_enable_interrupts(struct mali_gp_core *core, enum mali_interrupt_result exceptions)
+{
+	/* Enable all interrupts, except those specified in exceptions */
+	u32 value;
+
+	if (MALI_INTERRUPT_RESULT_SUCCESS_VS == exceptions) {
+		/* Enable all used except VS complete */
+		value = MALIGP2_REG_VAL_IRQ_MASK_USED &
+			~MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST;
+	} else {
+		MALI_DEBUG_ASSERT(MALI_INTERRUPT_RESULT_SUCCESS_PLBU ==
+				  exceptions);
+		/* Enable all used except PLBU complete */
+		value = MALIGP2_REG_VAL_IRQ_MASK_USED &
+			~MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST;
+	}
+
+	mali_hw_core_register_write(&core->hw_core,
+				    MALIGP2_REG_ADDR_MGMT_INT_MASK,
+				    value);
+}
+
+MALI_STATIC_INLINE u32 mali_gp_read_plbu_alloc_start_addr(struct mali_gp_core *core)
+{
+	return mali_hw_core_register_read(&core->hw_core, MALIGP2_REG_ADDR_MGMT_PLBU_ALLOC_START_ADDR);
+}
+
+#endif /* __MALI_GP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_gp_job.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_gp_job.c
@@ -0,0 +1,302 @@
+/*
+ * Copyright (C) 2011-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_gp_job.h"
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_uk_types.h"
+#include "mali_memory_virtual.h"
+#include "mali_memory_defer_bind.h"
+
+static u32 gp_counter_src0 = MALI_HW_CORE_NO_COUNTER;      /**< Performance counter 0, MALI_HW_CORE_NO_COUNTER for disabled */
+static u32 gp_counter_src1 = MALI_HW_CORE_NO_COUNTER;           /**< Performance counter 1, MALI_HW_CORE_NO_COUNTER for disabled */
+static void _mali_gp_del_varying_allocations(struct mali_gp_job *job);
+
+
+static int _mali_gp_add_varying_allocations(struct mali_session_data *session,
+		struct mali_gp_job *job,
+		u32 *alloc,
+		u32 num)
+{
+	int i = 0;
+	struct mali_gp_allocation_node *alloc_node;
+	mali_mem_allocation *mali_alloc = NULL;
+	struct mali_vma_node *mali_vma_node = NULL;
+
+	for (i = 0 ; i < num ; i++) {
+		MALI_DEBUG_ASSERT(alloc[i]);
+		alloc_node = _mali_osk_calloc(1, sizeof(struct mali_gp_allocation_node));
+		if (alloc_node) {
+			INIT_LIST_HEAD(&alloc_node->node);
+			/* find mali allocation structure by vaddress*/
+			mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, alloc[i], 0);
+
+			if (likely(mali_vma_node)) {
+				mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+				MALI_DEBUG_ASSERT(alloc[i] == mali_vma_node->vm_node.start);
+			} else {
+				MALI_DEBUG_PRINT(1, ("ERROE!_mali_gp_add_varying_allocations,can't find allocation %d by address =0x%x, num=%d\n", i, alloc[i], num));
+				_mali_osk_free(alloc_node);
+				goto fail;
+			}
+			alloc_node->alloc = mali_alloc;
+			/* add to gp job varying alloc list*/
+			list_move(&alloc_node->node, &job->varying_alloc);
+		} else
+			goto fail;
+	}
+
+	return 0;
+fail:
+	MALI_DEBUG_PRINT(1, ("ERROE!_mali_gp_add_varying_allocations,failed to alloc memory!\n"));
+	_mali_gp_del_varying_allocations(job);
+	return -1;
+}
+
+
+static void _mali_gp_del_varying_allocations(struct mali_gp_job *job)
+{
+	struct mali_gp_allocation_node *alloc_node, *tmp_node;
+
+	list_for_each_entry_safe(alloc_node, tmp_node, &job->varying_alloc, node) {
+		list_del(&alloc_node->node);
+		kfree(alloc_node);
+	}
+	INIT_LIST_HEAD(&job->varying_alloc);
+}
+
+struct mali_gp_job *mali_gp_job_create(struct mali_session_data *session, _mali_uk_gp_start_job_s *uargs, u32 id, struct mali_timeline_tracker *pp_tracker)
+{
+	struct mali_gp_job *job;
+	u32 perf_counter_flag;
+	u32 __user *memory_list = NULL;
+	struct mali_gp_allocation_node *alloc_node, *tmp_node;
+
+	job = _mali_osk_calloc(1, sizeof(struct mali_gp_job));
+	if (NULL != job) {
+		job->finished_notification = _mali_osk_notification_create(_MALI_NOTIFICATION_GP_FINISHED, sizeof(_mali_uk_gp_job_finished_s));
+		if (NULL == job->finished_notification) {
+			goto fail3;
+		}
+
+		job->oom_notification = _mali_osk_notification_create(_MALI_NOTIFICATION_GP_STALLED, sizeof(_mali_uk_gp_job_suspended_s));
+		if (NULL == job->oom_notification) {
+			goto fail2;
+		}
+
+		if (0 != _mali_osk_copy_from_user(&job->uargs, uargs, sizeof(_mali_uk_gp_start_job_s))) {
+			goto fail1;
+		}
+
+		perf_counter_flag = mali_gp_job_get_perf_counter_flag(job);
+
+		/* case when no counters came from user space
+		 * so pass the debugfs / DS-5 provided global ones to the job object */
+		if (!((perf_counter_flag & _MALI_PERFORMANCE_COUNTER_FLAG_SRC0_ENABLE) ||
+		      (perf_counter_flag & _MALI_PERFORMANCE_COUNTER_FLAG_SRC1_ENABLE))) {
+			mali_gp_job_set_perf_counter_src0(job, mali_gp_job_get_gp_counter_src0());
+			mali_gp_job_set_perf_counter_src1(job, mali_gp_job_get_gp_counter_src1());
+		}
+
+		_mali_osk_list_init(&job->list);
+		job->session = session;
+		job->id = id;
+		job->heap_current_addr = job->uargs.frame_registers[4];
+		job->perf_counter_value0 = 0;
+		job->perf_counter_value1 = 0;
+		job->pid = _mali_osk_get_pid();
+		job->tid = _mali_osk_get_tid();
+
+
+		INIT_LIST_HEAD(&job->varying_alloc);
+		INIT_LIST_HEAD(&job->vary_todo);
+		job->dmem = NULL;
+
+		if (job->uargs.deferred_mem_num > session->allocation_mgr.mali_allocation_num) {
+			MALI_PRINT_ERROR(("Mali GP job: The number of  varying buffer to defer bind  is invalid !\n"));
+			goto fail1;
+		}
+
+		/* add varying allocation list*/
+		if (job->uargs.deferred_mem_num > 0) {
+			/* copy varying list from user space*/
+			job->varying_list = _mali_osk_calloc(1, sizeof(u32) * job->uargs.deferred_mem_num);
+			if (!job->varying_list) {
+				MALI_PRINT_ERROR(("Mali GP job: allocate varying_list failed varying_alloc_num = %d !\n", job->uargs.deferred_mem_num));
+				goto fail1;
+			}
+
+			memory_list = (u32 __user *)(uintptr_t)job->uargs.deferred_mem_list;
+
+			if (0 != _mali_osk_copy_from_user(job->varying_list, memory_list, sizeof(u32) * job->uargs.deferred_mem_num)) {
+				MALI_PRINT_ERROR(("Mali GP job: Failed to copy varying list from user space!\n"));
+				goto fail;
+			}
+
+			if (unlikely(_mali_gp_add_varying_allocations(session, job, job->varying_list,
+					job->uargs.deferred_mem_num))) {
+				MALI_PRINT_ERROR(("Mali GP job: _mali_gp_add_varying_allocations failed!\n"));
+				goto fail;
+			}
+
+			/* do preparetion for each allocation */
+			list_for_each_entry_safe(alloc_node, tmp_node, &job->varying_alloc, node) {
+				if (unlikely(_MALI_OSK_ERR_OK != mali_mem_defer_bind_allocation_prepare(alloc_node->alloc, &job->vary_todo, &job->required_varying_memsize))) {
+					MALI_PRINT_ERROR(("Mali GP job: mali_mem_defer_bind_allocation_prepare failed!\n"));
+					goto fail;
+				}
+			}
+
+			_mali_gp_del_varying_allocations(job);
+
+			/* bind varying here, to avoid memory latency issue. */
+			{
+				struct mali_defer_mem_block dmem_block;
+
+				INIT_LIST_HEAD(&dmem_block.free_pages);
+				atomic_set(&dmem_block.num_free_pages, 0);
+
+				if (mali_mem_prepare_mem_for_job(job, &dmem_block)) {
+					MALI_PRINT_ERROR(("Mali GP job: mali_mem_prepare_mem_for_job failed!\n"));
+					goto fail;
+				}
+				if (_MALI_OSK_ERR_OK != mali_mem_defer_bind(job, &dmem_block)) {
+					MALI_PRINT_ERROR(("gp job create, mali_mem_defer_bind failed! GP %x fail!", job));
+					goto fail;
+				}
+			}
+
+			if (job->uargs.varying_memsize > MALI_UK_BIG_VARYING_SIZE) {
+				job->big_job = 1;
+			}
+		}
+		job->pp_tracker = pp_tracker;
+		if (NULL != job->pp_tracker) {
+			/* Take a reference on PP job's tracker that will be released when the GP
+			   job is done. */
+			mali_timeline_system_tracker_get(session->timeline_system, pp_tracker);
+		}
+
+		mali_timeline_tracker_init(&job->tracker, MALI_TIMELINE_TRACKER_GP, NULL, job);
+		mali_timeline_fence_copy_uk_fence(&(job->tracker.fence), &(job->uargs.fence));
+
+		return job;
+	} else {
+		MALI_PRINT_ERROR(("Mali GP job: _mali_osk_calloc failed!\n"));
+		return NULL;
+	}
+
+
+fail:
+	_mali_osk_free(job->varying_list);
+	/* Handle allocate fail here, free all varying node */
+	{
+		struct mali_backend_bind_list *bkn, *bkn_tmp;
+		list_for_each_entry_safe(bkn, bkn_tmp , &job->vary_todo, node) {
+			list_del(&bkn->node);
+			_mali_osk_free(bkn);
+		}
+	}
+fail1:
+	_mali_osk_notification_delete(job->oom_notification);
+fail2:
+	_mali_osk_notification_delete(job->finished_notification);
+fail3:
+	_mali_osk_free(job);
+	return NULL;
+}
+
+void mali_gp_job_delete(struct mali_gp_job *job)
+{
+	struct mali_backend_bind_list *bkn, *bkn_tmp;
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT(NULL == job->pp_tracker);
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(&job->list));
+	_mali_osk_free(job->varying_list);
+
+	/* Handle allocate fail here, free all varying node */
+	list_for_each_entry_safe(bkn, bkn_tmp , &job->vary_todo, node) {
+		list_del(&bkn->node);
+		_mali_osk_free(bkn);
+	}
+
+	mali_mem_defer_dmem_free(job);
+
+	/* de-allocate the pre-allocated oom notifications */
+	if (NULL != job->oom_notification) {
+		_mali_osk_notification_delete(job->oom_notification);
+		job->oom_notification = NULL;
+	}
+	if (NULL != job->finished_notification) {
+		_mali_osk_notification_delete(job->finished_notification);
+		job->finished_notification = NULL;
+	}
+
+	_mali_osk_free(job);
+}
+
+void mali_gp_job_list_add(struct mali_gp_job *job, _mali_osk_list_t *list)
+{
+	struct mali_gp_job *iter;
+	struct mali_gp_job *tmp;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+
+	/* Find position in list/queue where job should be added. */
+	_MALI_OSK_LIST_FOREACHENTRY_REVERSE(iter, tmp, list,
+					    struct mali_gp_job, list) {
+
+		/* A span is used to handle job ID wrapping. */
+		bool job_is_after = (mali_gp_job_get_id(job) -
+				     mali_gp_job_get_id(iter)) <
+				    MALI_SCHEDULER_JOB_ID_SPAN;
+
+		if (job_is_after) {
+			break;
+		}
+	}
+
+	_mali_osk_list_add(&job->list, &iter->list);
+}
+
+u32 mali_gp_job_get_gp_counter_src0(void)
+{
+	return gp_counter_src0;
+}
+
+void mali_gp_job_set_gp_counter_src0(u32 counter)
+{
+	gp_counter_src0 = counter;
+}
+
+u32 mali_gp_job_get_gp_counter_src1(void)
+{
+	return gp_counter_src1;
+}
+
+void mali_gp_job_set_gp_counter_src1(u32 counter)
+{
+	gp_counter_src1 = counter;
+}
+
+mali_scheduler_mask mali_gp_job_signal_pp_tracker(struct mali_gp_job *job, mali_bool success)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	if (NULL != job->pp_tracker) {
+		schedule_mask |= mali_timeline_system_tracker_put(job->session->timeline_system, job->pp_tracker, MALI_FALSE == success);
+		job->pp_tracker = NULL;
+	}
+
+	return schedule_mask;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_gp_job.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_gp_job.h
@@ -0,0 +1,324 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_GP_JOB_H__
+#define __MALI_GP_JOB_H__
+
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_uk_types.h"
+#include "mali_session.h"
+#include "mali_timeline.h"
+#include "mali_scheduler_types.h"
+#include "mali_scheduler.h"
+#include "mali_executor.h"
+#include "mali_timeline.h"
+
+struct mali_defer_mem;
+/**
+ * This structure represents a GP job
+ *
+ * The GP job object itself is not protected by any single lock,
+ * but relies on other locks instead (scheduler, executor and timeline lock).
+ * Think of the job object as moving between these sub systems through-out
+ * its lifetime. Different part of the GP job struct is used by different
+ * subsystems. Accessor functions ensure that correct lock is taken.
+ * Do NOT access any data members directly from outside this module!
+ */
+struct mali_gp_job {
+	/*
+	 * These members are typically only set at creation,
+	 * and only read later on.
+	 * They do not require any lock protection.
+	 */
+	_mali_uk_gp_start_job_s uargs;                     /**< Arguments from user space */
+	struct mali_session_data *session;                 /**< Session which submitted this job */
+	u32 pid;                                           /**< Process ID of submitting process */
+	u32 tid;                                           /**< Thread ID of submitting thread */
+	u32 id;                                            /**< Identifier for this job in kernel space (sequential numbering) */
+	u32 cache_order;                                   /**< Cache order used for L2 cache flushing (sequential numbering) */
+	struct mali_timeline_tracker tracker;              /**< Timeline tracker for this job */
+	struct mali_timeline_tracker *pp_tracker;          /**< Pointer to Timeline tracker for PP job that depends on this job. */
+	_mali_osk_notification_t *finished_notification;   /**< Notification sent back to userspace on job complete */
+
+	/*
+	 * These members are used by the scheduler,
+	 * protected by scheduler lock
+	 */
+	_mali_osk_list_t list;                             /**< Used to link jobs together in the scheduler queue */
+
+	/*
+	 * These members are used by the executor and/or group,
+	 * protected by executor lock
+	 */
+	_mali_osk_notification_t *oom_notification;        /**< Notification sent back to userspace on OOM */
+
+	/*
+	 * Set by executor/group on job completion, read by scheduler when
+	 * returning job to user. Hold executor lock when setting,
+	 * no lock needed when reading
+	 */
+	u32 heap_current_addr;                             /**< Holds the current HEAP address when the job has completed */
+	u32 perf_counter_value0;                           /**< Value of performance counter 0 (to be returned to user space) */
+	u32 perf_counter_value1;                           /**< Value of performance counter 1 (to be returned to user space) */
+	struct mali_defer_mem *dmem;                                          /** < used for defer bind to store dmem info */
+	struct list_head varying_alloc;                    /**< hold the list of varying allocations */
+	u32 bind_flag;                                     /** < flag for deferbind*/
+	u32 *varying_list;                                 /**< varying memory list need to to defer bind*/
+	struct list_head vary_todo;                        /**< list of backend list need to do defer bind*/
+	u32 required_varying_memsize;                      /** < size of varying memory to reallocate*/
+	u32 big_job;                                       /** < if the gp job have large varying output and may take long time*/
+};
+
+#define MALI_DEFER_BIND_MEMORY_PREPARED (0x1 << 0)
+#define MALI_DEFER_BIND_MEMORY_BINDED (0x1 << 2)
+
+struct mali_gp_allocation_node {
+	struct list_head node;
+	mali_mem_allocation *alloc;
+};
+
+struct mali_gp_job *mali_gp_job_create(struct mali_session_data *session, _mali_uk_gp_start_job_s *uargs, u32 id, struct mali_timeline_tracker *pp_tracker);
+void mali_gp_job_delete(struct mali_gp_job *job);
+
+u32 mali_gp_job_get_gp_counter_src0(void);
+void mali_gp_job_set_gp_counter_src0(u32 counter);
+u32 mali_gp_job_get_gp_counter_src1(void);
+void mali_gp_job_set_gp_counter_src1(u32 counter);
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_id(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (NULL == job) ? 0 : job->id;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_cache_order(struct mali_gp_job *job,
+		u32 cache_order)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	job->cache_order = cache_order;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_cache_order(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (NULL == job) ? 0 : job->cache_order;
+}
+
+MALI_STATIC_INLINE u64 mali_gp_job_get_user_id(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.user_job_ptr;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_frame_builder_id(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.frame_builder_id;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_flush_id(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.flush_id;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_pid(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->pid;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_tid(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->tid;
+}
+
+MALI_STATIC_INLINE u32 *mali_gp_job_get_frame_registers(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.frame_registers;
+}
+
+MALI_STATIC_INLINE struct mali_session_data *mali_gp_job_get_session(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->session;
+}
+
+MALI_STATIC_INLINE mali_bool mali_gp_job_has_vs_job(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (job->uargs.frame_registers[0] != job->uargs.frame_registers[1]) ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE mali_bool mali_gp_job_has_plbu_job(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (job->uargs.frame_registers[2] != job->uargs.frame_registers[3]) ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_current_heap_addr(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->heap_current_addr;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_current_heap_addr(struct mali_gp_job *job, u32 heap_addr)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	job->heap_current_addr = heap_addr;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_perf_counter_flag(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.perf_counter_flag;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_perf_counter_src0(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.perf_counter_src0;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_perf_counter_src1(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.perf_counter_src1;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_perf_counter_value0(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->perf_counter_value0;
+}
+
+MALI_STATIC_INLINE u32 mali_gp_job_get_perf_counter_value1(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->perf_counter_value1;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_perf_counter_src0(struct mali_gp_job *job, u32 src)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	job->uargs.perf_counter_src0 = src;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_perf_counter_src1(struct mali_gp_job *job, u32 src)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	job->uargs.perf_counter_src1 = src;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_perf_counter_value0(struct mali_gp_job *job, u32 value)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	job->perf_counter_value0 = value;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_perf_counter_value1(struct mali_gp_job *job, u32 value)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	job->perf_counter_value1 = value;
+}
+
+void mali_gp_job_list_add(struct mali_gp_job *job, _mali_osk_list_t *list);
+
+MALI_STATIC_INLINE void mali_gp_job_list_move(struct mali_gp_job *job,
+		_mali_osk_list_t *list)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	MALI_DEBUG_ASSERT(!_mali_osk_list_empty(&job->list));
+	_mali_osk_list_move(&job->list, list);
+}
+
+MALI_STATIC_INLINE void mali_gp_job_list_remove(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	_mali_osk_list_delinit(&job->list);
+}
+
+MALI_STATIC_INLINE _mali_osk_notification_t *
+mali_gp_job_get_finished_notification(struct mali_gp_job *job)
+{
+	_mali_osk_notification_t *notification;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(job->finished_notification);
+
+	notification = job->finished_notification;
+	job->finished_notification = NULL;
+
+	return notification;
+}
+
+MALI_STATIC_INLINE _mali_osk_notification_t *mali_gp_job_get_oom_notification(
+	struct mali_gp_job *job)
+{
+	_mali_osk_notification_t *notification;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT_POINTER(job->oom_notification);
+
+	notification = job->oom_notification;
+	job->oom_notification = NULL;
+
+	return notification;
+}
+
+MALI_STATIC_INLINE void mali_gp_job_set_oom_notification(
+	struct mali_gp_job *job,
+	_mali_osk_notification_t *notification)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(NULL == job->oom_notification);
+	job->oom_notification = notification;
+}
+
+MALI_STATIC_INLINE struct mali_timeline_tracker *mali_gp_job_get_tracker(
+	struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return &(job->tracker);
+}
+
+
+MALI_STATIC_INLINE u32 *mali_gp_job_get_timeline_point_ptr(
+	struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (u32 __user *)(uintptr_t)job->uargs.timeline_point_ptr;
+}
+
+
+/**
+ * Release reference on tracker for PP job that depends on this GP job.
+ *
+ * @note If GP job has a reference on tracker, this function MUST be called before the GP job is
+ * deleted.
+ *
+ * @param job GP job that is done.
+ * @param success MALI_TRUE if job completed successfully, MALI_FALSE if not.
+ * @return A scheduling bitmask indicating whether scheduling needs to be done.
+ */
+mali_scheduler_mask mali_gp_job_signal_pp_tracker(struct mali_gp_job *job, mali_bool success);
+
+#endif /* __MALI_GP_JOB_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_group.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_group.c
@@ -0,0 +1,1864 @@
+/*
+ * Copyright (C) 2011-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include "mali_kernel_common.h"
+#include "mali_group.h"
+#include "mali_osk.h"
+#include "mali_l2_cache.h"
+#include "mali_gp.h"
+#include "mali_pp.h"
+#include "mali_mmu.h"
+#include "mali_dlbu.h"
+#include "mali_broadcast.h"
+#include "mali_scheduler.h"
+#include "mali_osk_profiling.h"
+#include "mali_osk_mali.h"
+#include "mali_pm_domain.h"
+#include "mali_pm.h"
+#include "mali_executor.h"
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+#include <linux/sched.h>
+#include <trace/events/gpu.h>
+#endif
+
+#define MALI_MAX_NUM_DOMAIN_REFS (MALI_MAX_NUMBER_OF_GROUPS * 2)
+
+#if defined(CONFIG_MALI400_PROFILING)
+static void mali_group_report_l2_cache_counters_per_core(struct mali_group *group, u32 core_num);
+#endif /* #if defined(CONFIG_MALI400_PROFILING) */
+
+static struct mali_group *mali_global_groups[MALI_MAX_NUMBER_OF_GROUPS] = { NULL, };
+static u32 mali_global_num_groups = 0;
+
+/* SW timer for job execution */
+int mali_max_job_runtime = MALI_MAX_JOB_RUNTIME_DEFAULT;
+
+/* local helper functions */
+static void mali_group_bottom_half_mmu(void *data);
+static void mali_group_bottom_half_gp(void *data);
+static void mali_group_bottom_half_pp(void *data);
+static void mali_group_timeout(void *data);
+static void mali_group_reset_pp(struct mali_group *group);
+static void mali_group_reset_mmu(struct mali_group *group);
+
+static void mali_group_activate_page_directory(struct mali_group *group, struct mali_session_data *session, mali_bool is_reload);
+static void mali_group_recovery_reset(struct mali_group *group);
+
+struct mali_group *mali_group_create(struct mali_l2_cache_core *core,
+				     struct mali_dlbu_core *dlbu,
+				     struct mali_bcast_unit *bcast,
+				     u32 domain_index)
+{
+	struct mali_group *group = NULL;
+
+	if (mali_global_num_groups >= MALI_MAX_NUMBER_OF_GROUPS) {
+		MALI_PRINT_ERROR(("Mali group: Too many group objects created\n"));
+		return NULL;
+	}
+
+	group = _mali_osk_calloc(1, sizeof(struct mali_group));
+	if (NULL != group) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+		group->timeout_timer = _mali_osk_timer_init(mali_group_timeout);
+#else
+		group->timeout_timer = _mali_osk_timer_init();
+#endif
+		if (NULL != group->timeout_timer) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 14, 0)
+			_mali_osk_timer_setcallback(group->timeout_timer, mali_group_timeout, (void *)group);
+#endif
+
+			group->l2_cache_core[0] = core;
+			_mali_osk_list_init(&group->group_list);
+			_mali_osk_list_init(&group->executor_list);
+			_mali_osk_list_init(&group->pm_domain_list);
+			group->bcast_core = bcast;
+			group->dlbu_core = dlbu;
+
+			/* register this object as a part of the correct power domain */
+			if ((NULL != core) || (NULL != dlbu) || (NULL != bcast))
+				group->pm_domain = mali_pm_register_group(domain_index, group);
+
+			mali_global_groups[mali_global_num_groups] = group;
+			mali_global_num_groups++;
+
+			return group;
+		}
+		_mali_osk_free(group);
+	}
+
+	return NULL;
+}
+
+void mali_group_delete(struct mali_group *group)
+{
+	u32 i;
+
+	MALI_DEBUG_PRINT(4, ("Deleting group %s\n",
+			     mali_group_core_description(group)));
+
+	MALI_DEBUG_ASSERT(NULL == group->parent_group);
+	MALI_DEBUG_ASSERT((MALI_GROUP_STATE_INACTIVE == group->state) || ((MALI_GROUP_STATE_ACTIVATION_PENDING == group->state)));
+
+	/* Delete the resources that this group owns */
+	if (NULL != group->gp_core) {
+		mali_gp_delete(group->gp_core);
+	}
+
+	if (NULL != group->pp_core) {
+		mali_pp_delete(group->pp_core);
+	}
+
+	if (NULL != group->mmu) {
+		mali_mmu_delete(group->mmu);
+	}
+
+	if (mali_group_is_virtual(group)) {
+		/* Remove all groups from virtual group */
+		struct mali_group *child;
+		struct mali_group *temp;
+
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+			child->parent_group = NULL;
+			mali_group_delete(child);
+		}
+
+		mali_dlbu_delete(group->dlbu_core);
+
+		if (NULL != group->bcast_core) {
+			mali_bcast_unit_delete(group->bcast_core);
+		}
+	}
+
+	for (i = 0; i < mali_global_num_groups; i++) {
+		if (mali_global_groups[i] == group) {
+			mali_global_groups[i] = NULL;
+			mali_global_num_groups--;
+
+			if (i != mali_global_num_groups) {
+				/* We removed a group from the middle of the array -- move the last
+				 * group to the current position to close the gap */
+				mali_global_groups[i] = mali_global_groups[mali_global_num_groups];
+				mali_global_groups[mali_global_num_groups] = NULL;
+			}
+
+			break;
+		}
+	}
+
+	if (NULL != group->timeout_timer) {
+		_mali_osk_timer_del(group->timeout_timer);
+		_mali_osk_timer_term(group->timeout_timer);
+	}
+
+	if (NULL != group->bottom_half_work_mmu) {
+		_mali_osk_wq_delete_work(group->bottom_half_work_mmu);
+	}
+
+	if (NULL != group->bottom_half_work_gp) {
+		_mali_osk_wq_delete_work(group->bottom_half_work_gp);
+	}
+
+	if (NULL != group->bottom_half_work_pp) {
+		_mali_osk_wq_delete_work(group->bottom_half_work_pp);
+	}
+
+	_mali_osk_free(group);
+}
+
+_mali_osk_errcode_t mali_group_add_mmu_core(struct mali_group *group, struct mali_mmu_core *mmu_core)
+{
+	/* This group object now owns the MMU core object */
+	group->mmu = mmu_core;
+	group->bottom_half_work_mmu = _mali_osk_wq_create_work(mali_group_bottom_half_mmu, group);
+	if (NULL == group->bottom_half_work_mmu) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_group_remove_mmu_core(struct mali_group *group)
+{
+	/* This group object no longer owns the MMU core object */
+	group->mmu = NULL;
+	if (NULL != group->bottom_half_work_mmu) {
+		_mali_osk_wq_delete_work(group->bottom_half_work_mmu);
+	}
+}
+
+_mali_osk_errcode_t mali_group_add_gp_core(struct mali_group *group, struct mali_gp_core *gp_core)
+{
+	/* This group object now owns the GP core object */
+	group->gp_core = gp_core;
+	group->bottom_half_work_gp = _mali_osk_wq_create_work(mali_group_bottom_half_gp, group);
+	if (NULL == group->bottom_half_work_gp) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_group_remove_gp_core(struct mali_group *group)
+{
+	/* This group object no longer owns the GP core object */
+	group->gp_core = NULL;
+	if (NULL != group->bottom_half_work_gp) {
+		_mali_osk_wq_delete_work(group->bottom_half_work_gp);
+	}
+}
+
+_mali_osk_errcode_t mali_group_add_pp_core(struct mali_group *group, struct mali_pp_core *pp_core)
+{
+	/* This group object now owns the PP core object */
+	group->pp_core = pp_core;
+	group->bottom_half_work_pp = _mali_osk_wq_create_work(mali_group_bottom_half_pp, group);
+	if (NULL == group->bottom_half_work_pp) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_group_remove_pp_core(struct mali_group *group)
+{
+	/* This group object no longer owns the PP core object */
+	group->pp_core = NULL;
+	if (NULL != group->bottom_half_work_pp) {
+		_mali_osk_wq_delete_work(group->bottom_half_work_pp);
+	}
+}
+
+enum mali_group_state mali_group_activate(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	MALI_DEBUG_PRINT(4, ("Group: Activating group %s\n",
+			     mali_group_core_description(group)));
+
+	if (MALI_GROUP_STATE_INACTIVE == group->state) {
+		/* Group is inactive, get PM refs in order to power up */
+
+		/*
+		 * We'll take a maximum of 2 power domain references pr group,
+		 * one for the group itself, and one for it's L2 cache.
+		 */
+		struct mali_pm_domain *domains[MALI_MAX_NUM_DOMAIN_REFS];
+		struct mali_group *groups[MALI_MAX_NUM_DOMAIN_REFS];
+		u32 num_domains = 0;
+		mali_bool all_groups_on;
+
+		/* Deal with child groups first */
+		if (mali_group_is_virtual(group)) {
+			/*
+			 * The virtual group might have 0, 1 or 2 L2s in
+			 * its l2_cache_core array, but we ignore these and
+			 * let the child groups take the needed L2 cache ref
+			 * on behalf of the virtual group.
+			 * In other words; The L2 refs are taken in pair with
+			 * the physical group which the L2 is attached to.
+			 */
+			struct mali_group *child;
+			struct mali_group *temp;
+
+			/*
+			 * Child group is inactive, get PM
+			 * refs in order to power up.
+			 */
+			_MALI_OSK_LIST_FOREACHENTRY(child, temp,
+						    &group->group_list,
+						    struct mali_group, group_list) {
+				MALI_DEBUG_ASSERT(MALI_GROUP_STATE_INACTIVE
+						  == child->state);
+
+				child->state = MALI_GROUP_STATE_ACTIVATION_PENDING;
+
+				MALI_DEBUG_ASSERT_POINTER(
+					child->pm_domain);
+				domains[num_domains] = child->pm_domain;
+				groups[num_domains] = child;
+				num_domains++;
+
+				/*
+				 * Take L2 domain ref for child group.
+				 */
+				MALI_DEBUG_ASSERT(MALI_MAX_NUM_DOMAIN_REFS
+						  > num_domains);
+				domains[num_domains] = mali_l2_cache_get_pm_domain(
+							       child->l2_cache_core[0]);
+				groups[num_domains] = NULL;
+				MALI_DEBUG_ASSERT(NULL ==
+						  child->l2_cache_core[1]);
+				num_domains++;
+			}
+		} else {
+			/* Take L2 domain ref for physical groups. */
+			MALI_DEBUG_ASSERT(MALI_MAX_NUM_DOMAIN_REFS >
+					  num_domains);
+
+			domains[num_domains] = mali_l2_cache_get_pm_domain(
+						       group->l2_cache_core[0]);
+			groups[num_domains] = NULL;
+			MALI_DEBUG_ASSERT(NULL == group->l2_cache_core[1]);
+			num_domains++;
+		}
+
+		/* Do the group itself last (it's dependencies first) */
+
+		group->state = MALI_GROUP_STATE_ACTIVATION_PENDING;
+
+		MALI_DEBUG_ASSERT_POINTER(group->pm_domain);
+		domains[num_domains] = group->pm_domain;
+		groups[num_domains] = group;
+		num_domains++;
+
+		all_groups_on = mali_pm_get_domain_refs(domains, groups,
+							num_domains);
+
+		/*
+		 * Complete activation for group, include
+		 * virtual group or physical group.
+		 */
+		if (MALI_TRUE == all_groups_on) {
+
+			mali_group_set_active(group);
+		}
+	} else if (MALI_GROUP_STATE_ACTIVE == group->state) {
+		/* Already active */
+		MALI_DEBUG_ASSERT(MALI_TRUE == group->power_is_on);
+	} else {
+		/*
+		 * Activation already pending, group->power_is_on could
+		 * be both true or false. We need to wait for power up
+		 * notification anyway.
+		 */
+		MALI_DEBUG_ASSERT(MALI_GROUP_STATE_ACTIVATION_PENDING
+				  == group->state);
+	}
+
+	MALI_DEBUG_PRINT(4, ("Group: group %s activation result: %s\n",
+			     mali_group_core_description(group),
+			     MALI_GROUP_STATE_ACTIVE == group->state ?
+			     "ACTIVE" : "PENDING"));
+
+	return group->state;
+}
+
+mali_bool mali_group_set_active(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(MALI_GROUP_STATE_ACTIVATION_PENDING == group->state);
+	MALI_DEBUG_ASSERT(MALI_TRUE == group->power_is_on);
+
+	MALI_DEBUG_PRINT(4, ("Group: Activation completed for %s\n",
+			     mali_group_core_description(group)));
+
+	if (mali_group_is_virtual(group)) {
+		struct mali_group *child;
+		struct mali_group *temp;
+
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list,
+					    struct mali_group, group_list) {
+			if (MALI_TRUE != child->power_is_on) {
+				return MALI_FALSE;
+			}
+
+			child->state = MALI_GROUP_STATE_ACTIVE;
+		}
+
+		mali_group_reset(group);
+	}
+
+	/* Go to ACTIVE state */
+	group->state = MALI_GROUP_STATE_ACTIVE;
+
+	return MALI_TRUE;
+}
+
+mali_bool mali_group_deactivate(struct mali_group *group)
+{
+	struct mali_pm_domain *domains[MALI_MAX_NUM_DOMAIN_REFS];
+	u32 num_domains = 0;
+	mali_bool power_down = MALI_FALSE;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(MALI_GROUP_STATE_INACTIVE != group->state);
+
+	MALI_DEBUG_PRINT(3, ("Group: Deactivating group %s\n",
+			     mali_group_core_description(group)));
+
+	group->state = MALI_GROUP_STATE_INACTIVE;
+
+	MALI_DEBUG_ASSERT_POINTER(group->pm_domain);
+	domains[num_domains] = group->pm_domain;
+	num_domains++;
+
+	if (mali_group_is_virtual(group)) {
+		/* Release refs for all child groups */
+		struct mali_group *child;
+		struct mali_group *temp;
+
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp,
+					    &group->group_list,
+					    struct mali_group, group_list) {
+			child->state = MALI_GROUP_STATE_INACTIVE;
+
+			MALI_DEBUG_ASSERT_POINTER(child->pm_domain);
+			domains[num_domains] = child->pm_domain;
+			num_domains++;
+
+			/* Release L2 cache domain for child groups */
+			MALI_DEBUG_ASSERT(MALI_MAX_NUM_DOMAIN_REFS >
+					  num_domains);
+			domains[num_domains] = mali_l2_cache_get_pm_domain(
+						       child->l2_cache_core[0]);
+			MALI_DEBUG_ASSERT(NULL == child->l2_cache_core[1]);
+			num_domains++;
+		}
+
+		/*
+		 * Must do mali_group_power_down() steps right here for
+		 * virtual group, because virtual group itself is likely to
+		 * stay powered on, however child groups are now very likely
+		 * to be powered off (and thus lose their state).
+		 */
+
+		mali_group_clear_session(group);
+		/*
+		 * Disable the broadcast unit (clear it's mask).
+		 * This is needed in case the GPU isn't actually
+		 * powered down at this point and groups are
+		 * removed from an inactive virtual group.
+		 * If not, then the broadcast unit will intercept
+		 * their interrupts!
+		 */
+		mali_bcast_disable(group->bcast_core);
+	} else {
+		/* Release L2 cache domain for physical groups */
+		MALI_DEBUG_ASSERT(MALI_MAX_NUM_DOMAIN_REFS >
+				  num_domains);
+		domains[num_domains] = mali_l2_cache_get_pm_domain(
+					       group->l2_cache_core[0]);
+		MALI_DEBUG_ASSERT(NULL == group->l2_cache_core[1]);
+		num_domains++;
+	}
+
+	power_down = mali_pm_put_domain_refs(domains, num_domains);
+
+	return power_down;
+}
+
+void mali_group_power_up(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	MALI_DEBUG_PRINT(3, ("Group: Power up for %s\n",
+			     mali_group_core_description(group)));
+
+	group->power_is_on = MALI_TRUE;
+
+	if (MALI_FALSE == mali_group_is_virtual(group)
+	    && MALI_FALSE == mali_group_is_in_virtual(group)) {
+		mali_group_reset(group);
+	}
+
+	/*
+	 * When we just acquire only one physical group form virt group,
+	 * we should remove the bcast&dlbu mask from virt group and
+	 * reset bcast and dlbu core, although part of pp cores in virt
+	 * group maybe not be powered on.
+	 */
+	if (MALI_TRUE == mali_group_is_virtual(group)) {
+		mali_bcast_reset(group->bcast_core);
+		mali_dlbu_update_mask(group->dlbu_core);
+	}
+}
+
+void mali_group_power_down(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT(MALI_TRUE == group->power_is_on);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	MALI_DEBUG_PRINT(3, ("Group: Power down for %s\n",
+			     mali_group_core_description(group)));
+
+	group->power_is_on = MALI_FALSE;
+
+	if (mali_group_is_virtual(group)) {
+		/*
+		 * What we do for physical jobs in this function should
+		 * already have been done in mali_group_deactivate()
+		 * for virtual group.
+		 */
+		MALI_DEBUG_ASSERT(NULL == group->session);
+	} else {
+		mali_group_clear_session(group);
+	}
+}
+
+MALI_DEBUG_CODE(static void mali_group_print_virtual(struct mali_group *vgroup)
+{
+	u32 i;
+	struct mali_group *group;
+	struct mali_group *temp;
+
+	MALI_DEBUG_PRINT(4, ("Virtual group %s (%p)\n",
+			     mali_group_core_description(vgroup),
+			     vgroup));
+	MALI_DEBUG_PRINT(4, ("l2_cache_core[0] = %p, ref = %d\n", vgroup->l2_cache_core[0], vgroup->l2_cache_core_ref_count[0]));
+	MALI_DEBUG_PRINT(4, ("l2_cache_core[1] = %p, ref = %d\n", vgroup->l2_cache_core[1], vgroup->l2_cache_core_ref_count[1]));
+
+	i = 0;
+	_MALI_OSK_LIST_FOREACHENTRY(group, temp, &vgroup->group_list, struct mali_group, group_list) {
+		MALI_DEBUG_PRINT(4, ("[%d] %s (%p), l2_cache_core[0] = %p\n",
+				     i, mali_group_core_description(group),
+				     group, group->l2_cache_core[0]));
+		i++;
+	}
+})
+
+static void mali_group_dump_core_status(struct mali_group *group)
+{
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT(NULL != group->gp_core || (NULL != group->pp_core && !mali_group_is_virtual(group)));
+
+	if (NULL != group->gp_core) {
+		MALI_PRINT(("Dump Group %s\n", group->gp_core->hw_core.description));
+
+		for (i = 0; i < 0xA8; i += 0x10) {
+			MALI_PRINT(("0x%04x: 0x%08x 0x%08x 0x%08x 0x%08x\n", i, mali_hw_core_register_read(&group->gp_core->hw_core, i),
+				    mali_hw_core_register_read(&group->gp_core->hw_core, i + 4),
+				    mali_hw_core_register_read(&group->gp_core->hw_core, i + 8),
+				    mali_hw_core_register_read(&group->gp_core->hw_core, i + 12)));
+		}
+
+
+	} else {
+		MALI_PRINT(("Dump Group %s\n", group->pp_core->hw_core.description));
+
+		for (i = 0; i < 0x5c; i += 0x10) {
+			MALI_PRINT(("0x%04x: 0x%08x 0x%08x 0x%08x 0x%08x\n", i, mali_hw_core_register_read(&group->pp_core->hw_core, i),
+				    mali_hw_core_register_read(&group->pp_core->hw_core, i + 4),
+				    mali_hw_core_register_read(&group->pp_core->hw_core, i + 8),
+				    mali_hw_core_register_read(&group->pp_core->hw_core, i + 12)));
+		}
+
+		/* Ignore some minor registers */
+		for (i = 0x1000; i < 0x1068; i += 0x10) {
+			MALI_PRINT(("0x%04x: 0x%08x 0x%08x 0x%08x 0x%08x\n", i, mali_hw_core_register_read(&group->pp_core->hw_core, i),
+				    mali_hw_core_register_read(&group->pp_core->hw_core, i + 4),
+				    mali_hw_core_register_read(&group->pp_core->hw_core, i + 8),
+				    mali_hw_core_register_read(&group->pp_core->hw_core, i + 12)));
+		}
+	}
+
+	MALI_PRINT(("Dump Group MMU\n"));
+	for (i = 0; i < 0x24; i += 0x10) {
+		MALI_PRINT(("0x%04x: 0x%08x 0x%08x 0x%08x 0x%08x\n", i, mali_hw_core_register_read(&group->mmu->hw_core, i),
+			    mali_hw_core_register_read(&group->mmu->hw_core, i + 4),
+			    mali_hw_core_register_read(&group->mmu->hw_core, i + 8),
+			    mali_hw_core_register_read(&group->mmu->hw_core, i + 12)));
+	}
+}
+
+
+/**
+ * @Dump group status
+ */
+void mali_group_dump_status(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	if (mali_group_is_virtual(group)) {
+		struct mali_group *group_c;
+		struct mali_group *temp;
+		_MALI_OSK_LIST_FOREACHENTRY(group_c, temp, &group->group_list, struct mali_group, group_list) {
+			mali_group_dump_core_status(group_c);
+		}
+	} else {
+		mali_group_dump_core_status(group);
+	}
+}
+
+/**
+ * @brief Add child group to virtual group parent
+ */
+void mali_group_add_group(struct mali_group *parent, struct mali_group *child)
+{
+	mali_bool found;
+	u32 i;
+
+	MALI_DEBUG_PRINT(3, ("Adding group %s to virtual group %s\n",
+			     mali_group_core_description(child),
+			     mali_group_core_description(parent)));
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_group_is_virtual(parent));
+	MALI_DEBUG_ASSERT(!mali_group_is_virtual(child));
+	MALI_DEBUG_ASSERT(NULL == child->parent_group);
+
+	_mali_osk_list_addtail(&child->group_list, &parent->group_list);
+
+	child->parent_group = parent;
+
+	MALI_DEBUG_ASSERT_POINTER(child->l2_cache_core[0]);
+
+	MALI_DEBUG_PRINT(4, ("parent->l2_cache_core: [0] = %p, [1] = %p\n", parent->l2_cache_core[0], parent->l2_cache_core[1]));
+	MALI_DEBUG_PRINT(4, ("child->l2_cache_core: [0] = %p, [1] = %p\n", child->l2_cache_core[0], child->l2_cache_core[1]));
+
+	/* Keep track of the L2 cache cores of child groups */
+	found = MALI_FALSE;
+	for (i = 0; i < 2; i++) {
+		if (parent->l2_cache_core[i] == child->l2_cache_core[0]) {
+			MALI_DEBUG_ASSERT(parent->l2_cache_core_ref_count[i] > 0);
+			parent->l2_cache_core_ref_count[i]++;
+			found = MALI_TRUE;
+		}
+	}
+
+	if (!found) {
+		/* First time we see this L2 cache, add it to our list */
+		i = (NULL == parent->l2_cache_core[0]) ? 0 : 1;
+
+		MALI_DEBUG_PRINT(4, ("First time we see l2_cache %p. Adding to [%d] = %p\n", child->l2_cache_core[0], i, parent->l2_cache_core[i]));
+
+		MALI_DEBUG_ASSERT(NULL == parent->l2_cache_core[i]);
+
+		parent->l2_cache_core[i] = child->l2_cache_core[0];
+		parent->l2_cache_core_ref_count[i]++;
+	}
+
+	/* Update Broadcast Unit and DLBU */
+	mali_bcast_add_group(parent->bcast_core, child);
+	mali_dlbu_add_group(parent->dlbu_core, child);
+
+	if (MALI_TRUE == parent->power_is_on) {
+		mali_bcast_reset(parent->bcast_core);
+		mali_dlbu_update_mask(parent->dlbu_core);
+	}
+
+	if (MALI_TRUE == child->power_is_on) {
+		if (NULL == parent->session) {
+			if (NULL != child->session) {
+				/*
+				 * Parent has no session, so clear
+				 * child session as well.
+				 */
+				mali_mmu_activate_empty_page_directory(child->mmu);
+			}
+		} else {
+			if (parent->session == child->session) {
+				/* We already have same session as parent,
+				 * so a simple zap should be enough.
+				 */
+				mali_mmu_zap_tlb(child->mmu);
+			} else {
+				/*
+				 * Parent has a different session, so we must
+				 * switch to that sessions page table
+				 */
+				mali_mmu_activate_page_directory(child->mmu, mali_session_get_page_directory(parent->session));
+			}
+
+			/* It is the parent which keeps the session from now on */
+			child->session = NULL;
+		}
+	} else {
+		/* should have been cleared when child was powered down */
+		MALI_DEBUG_ASSERT(NULL == child->session);
+	}
+
+	/* Start job on child when parent is active */
+	if (NULL != parent->pp_running_job) {
+		struct mali_pp_job *job = parent->pp_running_job;
+
+		MALI_DEBUG_PRINT(3, ("Group %x joining running job %d on virtual group %x\n",
+				     child, mali_pp_job_get_id(job), parent));
+
+		/* Only allowed to add active child to an active parent */
+		MALI_DEBUG_ASSERT(MALI_GROUP_STATE_ACTIVE == parent->state);
+		MALI_DEBUG_ASSERT(MALI_GROUP_STATE_ACTIVE == child->state);
+
+		mali_pp_job_start(child->pp_core, job, mali_pp_core_get_id(child->pp_core), MALI_TRUE);
+
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+					      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(child->pp_core)) |
+					      MALI_PROFILING_EVENT_REASON_SINGLE_HW_FLUSH,
+					      mali_pp_job_get_frame_builder_id(job), mali_pp_job_get_flush_id(job), 0, 0, 0);
+
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+					      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(child->pp_core)) |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_HW_VIRTUAL,
+					      mali_pp_job_get_pid(job), mali_pp_job_get_tid(job), 0, 0, 0);
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+		trace_gpu_sched_switch(
+			mali_pp_core_description(group->pp_core),
+			sched_clock(), mali_pp_job_get_tid(job),
+			0, mali_pp_job_get_id(job));
+#endif
+
+#if defined(CONFIG_MALI400_PROFILING)
+		trace_mali_core_active(mali_pp_job_get_pid(job), 1 /* active */, 0 /* PP */, mali_pp_core_get_id(child->pp_core),
+				       mali_pp_job_get_frame_builder_id(job), mali_pp_job_get_flush_id(job));
+#endif
+	}
+
+	MALI_DEBUG_CODE(mali_group_print_virtual(parent);)
+}
+
+/**
+ * @brief Remove child group from virtual group parent
+ */
+void mali_group_remove_group(struct mali_group *parent, struct mali_group *child)
+{
+	u32 i;
+
+	MALI_DEBUG_PRINT(3, ("Removing group %s from virtual group %s\n",
+			     mali_group_core_description(child),
+			     mali_group_core_description(parent)));
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_group_is_virtual(parent));
+	MALI_DEBUG_ASSERT(!mali_group_is_virtual(child));
+	MALI_DEBUG_ASSERT(parent == child->parent_group);
+
+	/* Update Broadcast Unit and DLBU */
+	mali_bcast_remove_group(parent->bcast_core, child);
+	mali_dlbu_remove_group(parent->dlbu_core, child);
+
+	if (MALI_TRUE == parent->power_is_on) {
+		mali_bcast_reset(parent->bcast_core);
+		mali_dlbu_update_mask(parent->dlbu_core);
+	}
+
+	child->session = parent->session;
+	child->parent_group = NULL;
+
+	_mali_osk_list_delinit(&child->group_list);
+	if (_mali_osk_list_empty(&parent->group_list)) {
+		parent->session = NULL;
+	}
+
+	/* Keep track of the L2 cache cores of child groups */
+	i = (child->l2_cache_core[0] == parent->l2_cache_core[0]) ? 0 : 1;
+
+	MALI_DEBUG_ASSERT(child->l2_cache_core[0] == parent->l2_cache_core[i]);
+
+	parent->l2_cache_core_ref_count[i]--;
+	if (parent->l2_cache_core_ref_count[i] == 0) {
+		parent->l2_cache_core[i] = NULL;
+	}
+
+	MALI_DEBUG_CODE(mali_group_print_virtual(parent));
+}
+
+struct mali_group *mali_group_acquire_group(struct mali_group *parent)
+{
+	struct mali_group *child = NULL;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(mali_group_is_virtual(parent));
+
+	if (!_mali_osk_list_empty(&parent->group_list)) {
+		child = _MALI_OSK_LIST_ENTRY(parent->group_list.prev, struct mali_group, group_list);
+		mali_group_remove_group(parent, child);
+	}
+
+	if (NULL != child) {
+		if (MALI_GROUP_STATE_ACTIVE != parent->state
+		    && MALI_TRUE == child->power_is_on) {
+			mali_group_reset(child);
+		}
+	}
+
+	return child;
+}
+
+void mali_group_reset(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT(NULL == group->gp_running_job);
+	MALI_DEBUG_ASSERT(NULL == group->pp_running_job);
+
+	MALI_DEBUG_PRINT(3, ("Group: reset of %s\n",
+			     mali_group_core_description(group)));
+
+	if (NULL != group->dlbu_core) {
+		mali_dlbu_reset(group->dlbu_core);
+	}
+
+	if (NULL != group->bcast_core) {
+		mali_bcast_reset(group->bcast_core);
+	}
+
+	MALI_DEBUG_ASSERT(NULL != group->mmu);
+	mali_group_reset_mmu(group);
+
+	if (NULL != group->gp_core) {
+		MALI_DEBUG_ASSERT(NULL == group->pp_core);
+		mali_gp_reset(group->gp_core);
+	} else {
+		MALI_DEBUG_ASSERT(NULL != group->pp_core);
+		mali_group_reset_pp(group);
+	}
+}
+
+void mali_group_start_gp_job(struct mali_group *group, struct mali_gp_job *job, mali_bool gpu_secure_mode_pre_enabled)
+{
+	struct mali_session_data *session;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	MALI_DEBUG_PRINT(3, ("Group: Starting GP job 0x%08X on group %s\n",
+			     job,
+			     mali_group_core_description(group)));
+
+	session = mali_gp_job_get_session(job);
+
+	MALI_DEBUG_ASSERT_POINTER(group->l2_cache_core[0]);
+	mali_l2_cache_invalidate_conditional(group->l2_cache_core[0], mali_gp_job_get_cache_order(job));
+
+	/* Reset GPU and disable gpu secure mode if needed. */
+	if (MALI_TRUE == _mali_osk_gpu_secure_mode_is_enabled()) {
+		struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+		_mali_osk_gpu_reset_and_secure_mode_disable();
+		/* Need to disable the pmu interrupt mask register */
+		if (NULL != pmu) {
+			mali_pmu_reset(pmu);
+		}
+	}
+
+	/* Reload mmu page table if needed */
+	if (MALI_TRUE == gpu_secure_mode_pre_enabled) {
+		mali_group_reset(group);
+		mali_group_activate_page_directory(group, session, MALI_TRUE);
+	} else {
+		mali_group_activate_page_directory(group, session, MALI_FALSE);
+	}
+
+	mali_gp_job_start(group->gp_core, job);
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+				      MALI_PROFILING_MAKE_EVENT_CHANNEL_GP(0) |
+				      MALI_PROFILING_EVENT_REASON_SINGLE_HW_FLUSH,
+				      mali_gp_job_get_frame_builder_id(job), mali_gp_job_get_flush_id(job), 0, 0, 0);
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+				      MALI_PROFILING_MAKE_EVENT_CHANNEL_GP(0),
+				      mali_gp_job_get_pid(job), mali_gp_job_get_tid(job), 0, 0, 0);
+
+#if defined(CONFIG_MALI400_PROFILING)
+	trace_mali_core_active(mali_gp_job_get_pid(job), 1 /* active */, 1 /* GP */,  0 /* core */,
+			       mali_gp_job_get_frame_builder_id(job), mali_gp_job_get_flush_id(job));
+#endif
+
+#if defined(CONFIG_MALI400_PROFILING)
+	if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[0])) &&
+	    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[0]))) {
+		mali_group_report_l2_cache_counters_per_core(group, 0);
+	}
+#endif /* #if defined(CONFIG_MALI400_PROFILING) */
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+	trace_gpu_sched_switch(mali_gp_core_description(group->gp_core),
+			       sched_clock(), mali_gp_job_get_tid(job),
+			       0, mali_gp_job_get_id(job));
+#endif
+
+	group->gp_running_job = job;
+	group->is_working = MALI_TRUE;
+
+	/* Setup SW timer and record start time */
+	group->start_time = _mali_osk_time_tickcount();
+	_mali_osk_timer_mod(group->timeout_timer, _mali_osk_time_mstoticks(mali_max_job_runtime));
+
+	MALI_DEBUG_PRINT(4, ("Group: Started GP job 0x%08X on group %s at %u\n",
+			     job,
+			     mali_group_core_description(group),
+			     group->start_time));
+}
+
+/* Used to set all the registers except frame renderer list address and fragment shader stack address
+ * It means the caller must set these two registers properly before calling this function
+ */
+void mali_group_start_pp_job(struct mali_group *group, struct mali_pp_job *job, u32 sub_job, mali_bool gpu_secure_mode_pre_enabled)
+{
+	struct mali_session_data *session;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	MALI_DEBUG_PRINT(3, ("Group: Starting PP job 0x%08X part %u/%u on group %s\n",
+			     job, sub_job + 1,
+			     mali_pp_job_get_sub_job_count(job),
+			     mali_group_core_description(group)));
+
+	session = mali_pp_job_get_session(job);
+
+	if (NULL != group->l2_cache_core[0]) {
+		mali_l2_cache_invalidate_conditional(group->l2_cache_core[0], mali_pp_job_get_cache_order(job));
+	}
+
+	if (NULL != group->l2_cache_core[1]) {
+		mali_l2_cache_invalidate_conditional(group->l2_cache_core[1], mali_pp_job_get_cache_order(job));
+	}
+
+	/* Reset GPU and change gpu secure mode if needed. */
+	if (MALI_TRUE == mali_pp_job_is_protected_job(job) && MALI_FALSE == _mali_osk_gpu_secure_mode_is_enabled()) {
+		struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+		_mali_osk_gpu_reset_and_secure_mode_enable();
+		/* Need to disable the pmu interrupt mask register */
+		if (NULL != pmu) {
+			mali_pmu_reset(pmu);
+		}
+	} else if (MALI_FALSE == mali_pp_job_is_protected_job(job) && MALI_TRUE == _mali_osk_gpu_secure_mode_is_enabled()) {
+		struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+		_mali_osk_gpu_reset_and_secure_mode_disable();
+		/* Need to disable the pmu interrupt mask register */
+		if (NULL != pmu) {
+			mali_pmu_reset(pmu);
+		}
+	}
+
+	/* Reload the mmu page table if needed */
+	if ((MALI_TRUE == mali_pp_job_is_protected_job(job) && MALI_FALSE == gpu_secure_mode_pre_enabled)
+	    || (MALI_FALSE == mali_pp_job_is_protected_job(job) && MALI_TRUE == gpu_secure_mode_pre_enabled)) {
+		mali_group_reset(group);
+		mali_group_activate_page_directory(group, session, MALI_TRUE);
+	} else {
+		mali_group_activate_page_directory(group, session, MALI_FALSE);
+	}
+
+	if (mali_group_is_virtual(group)) {
+		struct mali_group *child;
+		struct mali_group *temp;
+		u32 core_num = 0;
+
+		MALI_DEBUG_ASSERT(mali_pp_job_is_virtual(job));
+
+		/* Configure DLBU for the job */
+		mali_dlbu_config_job(group->dlbu_core, job);
+
+		/* Write stack address for each child group */
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+			mali_pp_write_addr_stack(child->pp_core, job);
+			core_num++;
+		}
+
+		mali_pp_job_start(group->pp_core, job, sub_job, MALI_FALSE);
+	} else {
+		mali_pp_job_start(group->pp_core, job, sub_job, MALI_FALSE);
+	}
+
+	/* if the group is virtual, loop through physical groups which belong to this group
+	 * and call profiling events for its cores as virtual */
+	if (MALI_TRUE == mali_group_is_virtual(group)) {
+		struct mali_group *child;
+		struct mali_group *temp;
+
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+			_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+						      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(child->pp_core)) |
+						      MALI_PROFILING_EVENT_REASON_SINGLE_HW_FLUSH,
+						      mali_pp_job_get_frame_builder_id(job), mali_pp_job_get_flush_id(job), 0, 0, 0);
+
+			_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+						      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(child->pp_core)) |
+						      MALI_PROFILING_EVENT_REASON_START_STOP_HW_VIRTUAL,
+						      mali_pp_job_get_pid(job), mali_pp_job_get_tid(job), 0, 0, 0);
+
+#if defined(CONFIG_MALI400_PROFILING)
+			trace_mali_core_active(mali_pp_job_get_pid(job), 1 /* active */, 0 /* PP */, mali_pp_core_get_id(child->pp_core),
+					       mali_pp_job_get_frame_builder_id(job), mali_pp_job_get_flush_id(job));
+#endif
+		}
+
+#if defined(CONFIG_MALI400_PROFILING)
+		if (0 != group->l2_cache_core_ref_count[0]) {
+			if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[0])) &&
+			    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[0]))) {
+				mali_group_report_l2_cache_counters_per_core(group, mali_l2_cache_get_id(group->l2_cache_core[0]));
+			}
+		}
+		if (0 != group->l2_cache_core_ref_count[1]) {
+			if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[1])) &&
+			    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[1]))) {
+				mali_group_report_l2_cache_counters_per_core(group, mali_l2_cache_get_id(group->l2_cache_core[1]));
+			}
+		}
+#endif /* #if defined(CONFIG_MALI400_PROFILING) */
+
+	} else { /* group is physical - call profiling events for physical cores */
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+					      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(group->pp_core)) |
+					      MALI_PROFILING_EVENT_REASON_SINGLE_HW_FLUSH,
+					      mali_pp_job_get_frame_builder_id(job), mali_pp_job_get_flush_id(job), 0, 0, 0);
+
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+					      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(group->pp_core)) |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_HW_PHYSICAL,
+					      mali_pp_job_get_pid(job), mali_pp_job_get_tid(job), 0, 0, 0);
+
+#if defined(CONFIG_MALI400_PROFILING)
+		trace_mali_core_active(mali_pp_job_get_pid(job), 1 /* active */, 0 /* PP */, mali_pp_core_get_id(group->pp_core),
+				       mali_pp_job_get_frame_builder_id(job), mali_pp_job_get_flush_id(job));
+#endif
+
+#if defined(CONFIG_MALI400_PROFILING)
+		if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[0])) &&
+		    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[0]))) {
+			mali_group_report_l2_cache_counters_per_core(group, mali_l2_cache_get_id(group->l2_cache_core[0]));
+		}
+#endif /* #if defined(CONFIG_MALI400_PROFILING) */
+	}
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+	trace_gpu_sched_switch(mali_pp_core_description(group->pp_core),
+			       sched_clock(), mali_pp_job_get_tid(job),
+			       0, mali_pp_job_get_id(job));
+#endif
+
+	group->pp_running_job = job;
+	group->pp_running_sub_job = sub_job;
+	group->is_working = MALI_TRUE;
+
+	/* Setup SW timer and record start time */
+	group->start_time = _mali_osk_time_tickcount();
+	_mali_osk_timer_mod(group->timeout_timer, _mali_osk_time_mstoticks(mali_max_job_runtime));
+
+	MALI_DEBUG_PRINT(4, ("Group: Started PP job 0x%08X part %u/%u on group %s at %u\n",
+			     job, sub_job + 1,
+			     mali_pp_job_get_sub_job_count(job),
+			     mali_group_core_description(group),
+			     group->start_time));
+
+}
+
+void mali_group_resume_gp_with_new_heap(struct mali_group *group, u32 job_id, u32 start_addr, u32 end_addr)
+{
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	MALI_DEBUG_ASSERT_POINTER(group->l2_cache_core[0]);
+	mali_l2_cache_invalidate(group->l2_cache_core[0]);
+
+	mali_mmu_zap_tlb_without_stall(group->mmu);
+
+	mali_gp_resume_with_new_heap(group->gp_core, start_addr, end_addr);
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_RESUME |
+				      MALI_PROFILING_MAKE_EVENT_CHANNEL_GP(0),
+				      0, 0, 0, 0, 0);
+
+#if defined(CONFIG_MALI400_PROFILING)
+	trace_mali_core_active(mali_gp_job_get_pid(group->gp_running_job), 1 /* active */, 1 /* GP */,  0 /* core */,
+			       mali_gp_job_get_frame_builder_id(group->gp_running_job), mali_gp_job_get_flush_id(group->gp_running_job));
+#endif
+}
+
+static void mali_group_reset_mmu(struct mali_group *group)
+{
+	struct mali_group *child;
+	struct mali_group *temp;
+	_mali_osk_errcode_t err;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	if (!mali_group_is_virtual(group)) {
+		/* This is a physical group or an idle virtual group -- simply wait for
+		 * the reset to complete. */
+		err = mali_mmu_reset(group->mmu);
+		MALI_DEBUG_ASSERT(_MALI_OSK_ERR_OK == err);
+	} else { /* virtual group */
+		/* Loop through all members of this virtual group and wait
+		 * until they are done resetting.
+		 */
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+			err = mali_mmu_reset(child->mmu);
+			MALI_DEBUG_ASSERT(_MALI_OSK_ERR_OK == err);
+		}
+	}
+}
+
+static void mali_group_reset_pp(struct mali_group *group)
+{
+	struct mali_group *child;
+	struct mali_group *temp;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	mali_pp_reset_async(group->pp_core);
+
+	if (!mali_group_is_virtual(group) || NULL == group->pp_running_job) {
+		/* This is a physical group or an idle virtual group -- simply wait for
+		 * the reset to complete. */
+		mali_pp_reset_wait(group->pp_core);
+	} else {
+		/* Loop through all members of this virtual group and wait until they
+		 * are done resetting.
+		 */
+		_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+			mali_pp_reset_wait(child->pp_core);
+		}
+	}
+}
+
+struct mali_pp_job *mali_group_complete_pp(struct mali_group *group, mali_bool success, u32 *sub_job)
+{
+	struct mali_pp_job *pp_job_to_return;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_running_job);
+	MALI_DEBUG_ASSERT_POINTER(sub_job);
+	MALI_DEBUG_ASSERT(MALI_TRUE == group->is_working);
+
+	/* Stop/clear the timeout timer. */
+	_mali_osk_timer_del_async(group->timeout_timer);
+
+	if (NULL != group->pp_running_job) {
+
+		/* Deal with HW counters and profiling */
+
+		if (MALI_TRUE == mali_group_is_virtual(group)) {
+			struct mali_group *child;
+			struct mali_group *temp;
+
+			/* update performance counters from each physical pp core within this virtual group */
+			_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+				mali_pp_update_performance_counters(group->pp_core, child->pp_core, group->pp_running_job, mali_pp_core_get_id(child->pp_core));
+			}
+
+#if defined(CONFIG_MALI400_PROFILING)
+			/* send profiling data per physical core */
+			_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+				_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+							      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(child->pp_core)) |
+							      MALI_PROFILING_EVENT_REASON_START_STOP_HW_VIRTUAL,
+							      mali_pp_job_get_perf_counter_value0(group->pp_running_job, mali_pp_core_get_id(child->pp_core)),
+							      mali_pp_job_get_perf_counter_value1(group->pp_running_job, mali_pp_core_get_id(child->pp_core)),
+							      mali_pp_job_get_perf_counter_src0(group->pp_running_job, group->pp_running_sub_job) | (mali_pp_job_get_perf_counter_src1(group->pp_running_job, group->pp_running_sub_job) << 8),
+							      0, 0);
+
+				trace_mali_core_active(mali_pp_job_get_pid(group->pp_running_job),
+						       0 /* active */, 0 /* PP */, mali_pp_core_get_id(child->pp_core),
+						       mali_pp_job_get_frame_builder_id(group->pp_running_job),
+						       mali_pp_job_get_flush_id(group->pp_running_job));
+			}
+			if (0 != group->l2_cache_core_ref_count[0]) {
+				if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[0])) &&
+				    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[0]))) {
+					mali_group_report_l2_cache_counters_per_core(group, mali_l2_cache_get_id(group->l2_cache_core[0]));
+				}
+			}
+			if (0 != group->l2_cache_core_ref_count[1]) {
+				if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[1])) &&
+				    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[1]))) {
+					mali_group_report_l2_cache_counters_per_core(group, mali_l2_cache_get_id(group->l2_cache_core[1]));
+				}
+			}
+
+#endif
+		} else {
+			/* update performance counters for a physical group's pp core */
+			mali_pp_update_performance_counters(group->pp_core, group->pp_core, group->pp_running_job, group->pp_running_sub_job);
+
+#if defined(CONFIG_MALI400_PROFILING)
+			_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+						      MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(mali_pp_core_get_id(group->pp_core)) |
+						      MALI_PROFILING_EVENT_REASON_START_STOP_HW_PHYSICAL,
+						      mali_pp_job_get_perf_counter_value0(group->pp_running_job, group->pp_running_sub_job),
+						      mali_pp_job_get_perf_counter_value1(group->pp_running_job, group->pp_running_sub_job),
+						      mali_pp_job_get_perf_counter_src0(group->pp_running_job, group->pp_running_sub_job) | (mali_pp_job_get_perf_counter_src1(group->pp_running_job, group->pp_running_sub_job) << 8),
+						      0, 0);
+
+			trace_mali_core_active(mali_pp_job_get_pid(group->pp_running_job),
+					       0 /* active */, 0 /* PP */, mali_pp_core_get_id(group->pp_core),
+					       mali_pp_job_get_frame_builder_id(group->pp_running_job),
+					       mali_pp_job_get_flush_id(group->pp_running_job));
+
+			if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[0])) &&
+			    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[0]))) {
+				mali_group_report_l2_cache_counters_per_core(group, mali_l2_cache_get_id(group->l2_cache_core[0]));
+			}
+#endif
+		}
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+		trace_gpu_sched_switch(
+			mali_gp_core_description(group->gp_core),
+			sched_clock(), 0, 0, 0);
+#endif
+
+	}
+
+	if (success) {
+		/* Only do soft reset for successful jobs, a full recovery
+		 * reset will be done for failed jobs. */
+		mali_pp_reset_async(group->pp_core);
+	}
+
+	pp_job_to_return = group->pp_running_job;
+	group->pp_running_job = NULL;
+	group->is_working = MALI_FALSE;
+	*sub_job = group->pp_running_sub_job;
+
+	if (!success) {
+		MALI_DEBUG_PRINT(2, ("Mali group: Executing recovery reset due to job failure\n"));
+		mali_group_recovery_reset(group);
+	} else if (_MALI_OSK_ERR_OK != mali_pp_reset_wait(group->pp_core)) {
+		MALI_PRINT_ERROR(("Mali group: Executing recovery reset due to reset failure\n"));
+		mali_group_recovery_reset(group);
+	}
+
+	return pp_job_to_return;
+}
+
+struct mali_gp_job *mali_group_complete_gp(struct mali_group *group, mali_bool success)
+{
+	struct mali_gp_job *gp_job_to_return;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_running_job);
+	MALI_DEBUG_ASSERT(MALI_TRUE == group->is_working);
+
+	/* Stop/clear the timeout timer. */
+	_mali_osk_timer_del_async(group->timeout_timer);
+
+	if (NULL != group->gp_running_job) {
+		mali_gp_update_performance_counters(group->gp_core, group->gp_running_job);
+
+#if defined(CONFIG_MALI400_PROFILING)
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP | MALI_PROFILING_MAKE_EVENT_CHANNEL_GP(0),
+					      mali_gp_job_get_perf_counter_value0(group->gp_running_job),
+					      mali_gp_job_get_perf_counter_value1(group->gp_running_job),
+					      mali_gp_job_get_perf_counter_src0(group->gp_running_job) | (mali_gp_job_get_perf_counter_src1(group->gp_running_job) << 8),
+					      0, 0);
+
+		if ((MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src0(group->l2_cache_core[0])) &&
+		    (MALI_HW_CORE_NO_COUNTER != mali_l2_cache_core_get_counter_src1(group->l2_cache_core[0])))
+			mali_group_report_l2_cache_counters_per_core(group, 0);
+#endif
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+		trace_gpu_sched_switch(
+			mali_pp_core_description(group->pp_core),
+			sched_clock(), 0, 0, 0);
+#endif
+
+#if defined(CONFIG_MALI400_PROFILING)
+		trace_mali_core_active(mali_gp_job_get_pid(group->gp_running_job), 0 /* active */, 1 /* GP */,  0 /* core */,
+				       mali_gp_job_get_frame_builder_id(group->gp_running_job), mali_gp_job_get_flush_id(group->gp_running_job));
+#endif
+
+		mali_gp_job_set_current_heap_addr(group->gp_running_job,
+						  mali_gp_read_plbu_alloc_start_addr(group->gp_core));
+	}
+
+	if (success) {
+		/* Only do soft reset for successful jobs, a full recovery
+		 * reset will be done for failed jobs. */
+		mali_gp_reset_async(group->gp_core);
+	}
+
+	gp_job_to_return = group->gp_running_job;
+	group->gp_running_job = NULL;
+	group->is_working = MALI_FALSE;
+
+	if (!success) {
+		MALI_DEBUG_PRINT(2, ("Mali group: Executing recovery reset due to job failure\n"));
+		mali_group_recovery_reset(group);
+	} else if (_MALI_OSK_ERR_OK != mali_gp_reset_wait(group->gp_core)) {
+		MALI_PRINT_ERROR(("Mali group: Executing recovery reset due to reset failure\n"));
+		mali_group_recovery_reset(group);
+	}
+
+	return gp_job_to_return;
+}
+
+struct mali_group *mali_group_get_glob_group(u32 index)
+{
+	if (mali_global_num_groups > index) {
+		return mali_global_groups[index];
+	}
+
+	return NULL;
+}
+
+u32 mali_group_get_glob_num_groups(void)
+{
+	return mali_global_num_groups;
+}
+
+static void mali_group_activate_page_directory(struct mali_group *group, struct mali_session_data *session, mali_bool is_reload)
+{
+	MALI_DEBUG_PRINT(5, ("Mali group: Activating page directory 0x%08X from session 0x%08X on group %s\n",
+			     mali_session_get_page_directory(session), session,
+			     mali_group_core_description(group)));
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	if (group->session != session || MALI_TRUE == is_reload) {
+		/* Different session than last time, so we need to do some work */
+		MALI_DEBUG_PRINT(5, ("Mali group: Activate session: %08x previous: %08x on group %s\n",
+				     session, group->session,
+				     mali_group_core_description(group)));
+		mali_mmu_activate_page_directory(group->mmu, mali_session_get_page_directory(session));
+		group->session = session;
+	} else {
+		/* Same session as last time, so no work required */
+		MALI_DEBUG_PRINT(4, ("Mali group: Activate existing session 0x%08X on group %s\n",
+				     session->page_directory,
+				     mali_group_core_description(group)));
+		mali_mmu_zap_tlb_without_stall(group->mmu);
+	}
+}
+
+static void mali_group_recovery_reset(struct mali_group *group)
+{
+	_mali_osk_errcode_t err;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	/* Stop cores, bus stop */
+	if (NULL != group->pp_core) {
+		mali_pp_stop_bus(group->pp_core);
+	} else {
+		mali_gp_stop_bus(group->gp_core);
+	}
+
+	/* Flush MMU and clear page fault (if any) */
+	mali_mmu_activate_fault_flush_page_directory(group->mmu);
+	mali_mmu_page_fault_done(group->mmu);
+
+	/* Wait for cores to stop bus, then do a hard reset on them */
+	if (NULL != group->pp_core) {
+		if (mali_group_is_virtual(group)) {
+			struct mali_group *child, *temp;
+
+			/* Disable the broadcast unit while we do reset directly on the member cores. */
+			mali_bcast_disable(group->bcast_core);
+
+			_MALI_OSK_LIST_FOREACHENTRY(child, temp, &group->group_list, struct mali_group, group_list) {
+				mali_pp_stop_bus_wait(child->pp_core);
+				mali_pp_hard_reset(child->pp_core);
+			}
+
+			mali_bcast_enable(group->bcast_core);
+		} else {
+			mali_pp_stop_bus_wait(group->pp_core);
+			mali_pp_hard_reset(group->pp_core);
+		}
+	} else {
+		mali_gp_stop_bus_wait(group->gp_core);
+		mali_gp_hard_reset(group->gp_core);
+	}
+
+	/* Reset MMU */
+	err = mali_mmu_reset(group->mmu);
+	MALI_DEBUG_ASSERT(_MALI_OSK_ERR_OK == err);
+	MALI_IGNORE(err);
+
+	group->session = NULL;
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_group_dump_state(struct mali_group *group, char *buf, u32 size)
+{
+	int n = 0;
+	int i;
+
+	if (mali_group_is_virtual(group)) {
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"Virtual PP Group: %p\n", group);
+	} else if (mali_group_is_in_virtual(group)) {
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"Child PP Group: %p\n", group);
+	} else if (NULL != group->pp_core) {
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"Physical PP Group: %p\n", group);
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"GP Group: %p\n", group);
+	}
+
+	switch (group->state) {
+	case MALI_GROUP_STATE_INACTIVE:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"\tstate: INACTIVE\n");
+		break;
+	case MALI_GROUP_STATE_ACTIVATION_PENDING:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"\tstate: ACTIVATION_PENDING\n");
+		break;
+	case MALI_GROUP_STATE_ACTIVE:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"\tstate: MALI_GROUP_STATE_ACTIVE\n");
+		break;
+	default:
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"\tstate: UNKNOWN (%d)\n", group->state);
+		MALI_DEBUG_ASSERT(0);
+		break;
+	}
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tSW power: %s\n",
+				group->power_is_on ? "On" : "Off");
+
+	n += mali_pm_dump_state_domain(group->pm_domain, buf + n, size - n);
+
+	for (i = 0; i < 2; i++) {
+		if (NULL != group->l2_cache_core[i]) {
+			struct mali_pm_domain *domain;
+			domain = mali_l2_cache_get_pm_domain(
+					 group->l2_cache_core[i]);
+			n += mali_pm_dump_state_domain(domain,
+						       buf + n, size - n);
+		}
+	}
+
+	if (group->gp_core) {
+		n += mali_gp_dump_state(group->gp_core, buf + n, size - n);
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"\tGP running job: %p\n", group->gp_running_job);
+	}
+
+	if (group->pp_core) {
+		n += mali_pp_dump_state(group->pp_core, buf + n, size - n);
+		n += _mali_osk_snprintf(buf + n, size - n,
+					"\tPP running job: %p, subjob %d \n",
+					group->pp_running_job,
+					group->pp_running_sub_job);
+	}
+
+	return n;
+}
+#endif
+
+_mali_osk_errcode_t mali_group_upper_half_mmu(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+	_mali_osk_errcode_t ret;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_lock();
+	if (!mali_group_is_working(group)) {
+		/* Not working, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif
+	if (NULL != group->gp_core) {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+					      0, 0, /* No pid and tid for interrupt handler */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP_MMU(0),
+					      mali_mmu_get_rawstat(group->mmu), 0);
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+					      0, 0, /* No pid and tid for interrupt handler */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP_MMU(
+						      mali_pp_core_get_id(group->pp_core)),
+					      mali_mmu_get_rawstat(group->mmu), 0);
+	}
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_unlock();
+#endif
+#endif
+
+	ret = mali_executor_interrupt_mmu(group, MALI_TRUE);
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_lock();
+	if (!mali_group_is_working(group) && (!mali_group_power_is_on(group))) {
+		/* group complete and on job shedule on it, it already power off */
+		if (NULL != group->gp_core) {
+			_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+						      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+						      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+						      0, 0, /* No pid and tid for interrupt handler */
+						      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP_MMU(0),
+						      0xFFFFFFFF, 0);
+		} else {
+			_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+						      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+						      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+						      0, 0, /* No pid and tid for interrupt handler */
+						      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP_MMU(
+							      mali_pp_core_get_id(group->pp_core)),
+						      0xFFFFFFFF, 0);
+		}
+
+		mali_executor_unlock();
+		return ret;
+	}
+#endif
+
+	if (NULL != group->gp_core) {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+					      0, 0, /* No pid and tid for interrupt handler */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP_MMU(0),
+					      0xFFFFFFFF, 0);
+	} else {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+					      0, 0, /* No pid and tid for interrupt handler */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP_MMU(
+						      mali_pp_core_get_id(group->pp_core)),
+					      0xFFFFFFFF, 0);
+	}
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_unlock();
+#endif
+#endif
+
+	return ret;
+}
+
+static void mali_group_bottom_half_mmu(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+
+	if (NULL != group->gp_core) {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+					      0, _mali_osk_get_tid(), /* pid and tid */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP_MMU(0),
+					      0xFFFFFFFF, 0);
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+					      0, _mali_osk_get_tid(), /* pid and tid */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP_MMU(
+						      mali_pp_core_get_id(group->pp_core)),
+					      0xFFFFFFFF, 0);
+	}
+
+	mali_executor_interrupt_mmu(group, MALI_FALSE);
+
+	if (NULL != group->gp_core) {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+					      0, _mali_osk_get_tid(), /* pid and tid */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP_MMU(0),
+					      0xFFFFFFFF, 0);
+	} else {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+					      0, _mali_osk_get_tid(), /* pid and tid */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP_MMU(
+						      mali_pp_core_get_id(group->pp_core)),
+					      0xFFFFFFFF, 0);
+	}
+}
+
+_mali_osk_errcode_t mali_group_upper_half_gp(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+	_mali_osk_errcode_t ret;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_lock();
+	if (!mali_group_is_working(group)) {
+		/* Not working, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+				      0, 0, /* No pid and tid for interrupt handler */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP(0),
+				      mali_gp_get_rawstat(group->gp_core), 0);
+
+	MALI_DEBUG_PRINT(4, ("Group: Interrupt 0x%08X from %s\n",
+			     mali_gp_get_rawstat(group->gp_core),
+			     mali_group_core_description(group)));
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_unlock();
+#endif
+#endif
+	ret = mali_executor_interrupt_gp(group, MALI_TRUE);
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_lock();
+	if (!mali_group_is_working(group) && (!mali_group_power_is_on(group))) {
+		/* group complete and on job shedule on it, it already power off */
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+					      0, 0, /* No pid and tid for interrupt handler */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP(0),
+					      0xFFFFFFFF, 0);
+		mali_executor_unlock();
+		return ret;
+	}
+#endif
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+				      0, 0, /* No pid and tid for interrupt handler */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP(0),
+				      0xFFFFFFFF, 0);
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_unlock();
+#endif
+#endif
+	return ret;
+}
+
+static void mali_group_bottom_half_gp(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+				      0, _mali_osk_get_tid(), /* pid and tid */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP(0),
+				      0xFFFFFFFF, 0);
+
+	mali_executor_interrupt_gp(group, MALI_FALSE);
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+				      0, _mali_osk_get_tid(), /* pid and tid */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP(0),
+				      0xFFFFFFFF, 0);
+}
+
+_mali_osk_errcode_t mali_group_upper_half_pp(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+	_mali_osk_errcode_t ret;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_lock();
+	if (!mali_group_is_working(group)) {
+		/* Not working, so nothing to do */
+		mali_executor_unlock();
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+				      0, 0, /* No pid and tid for interrupt handler */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP(
+					      mali_pp_core_get_id(group->pp_core)),
+				      mali_pp_get_rawstat(group->pp_core), 0);
+
+	MALI_DEBUG_PRINT(4, ("Group: Interrupt 0x%08X from %s\n",
+			     mali_pp_get_rawstat(group->pp_core),
+			     mali_group_core_description(group)));
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_unlock();
+#endif
+#endif
+
+	ret = mali_executor_interrupt_pp(group, MALI_TRUE);
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_lock();
+	if (!mali_group_is_working(group) && (!mali_group_power_is_on(group))) {
+		/* group complete and on job shedule on it, it already power off */
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+					      0, 0, /* No pid and tid for interrupt handler */
+					      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP(
+						      mali_pp_core_get_id(group->pp_core)),
+					      0xFFFFFFFF, 0);
+		mali_executor_unlock();
+		return ret;
+	}
+#endif
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF,
+				      0, 0, /* No pid and tid for interrupt handler */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP(
+					      mali_pp_core_get_id(group->pp_core)),
+				      0xFFFFFFFF, 0);
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	mali_executor_unlock();
+#endif
+#endif
+	return ret;
+}
+
+static void mali_group_bottom_half_pp(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_START |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+				      0, _mali_osk_get_tid(), /* pid and tid */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP(
+					      mali_pp_core_get_id(group->pp_core)),
+				      0xFFFFFFFF, 0);
+
+	mali_executor_interrupt_pp(group, MALI_FALSE);
+
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_STOP |
+				      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+				      MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF,
+				      0, _mali_osk_get_tid(), /* pid and tid */
+				      MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP(
+					      mali_pp_core_get_id(group->pp_core)),
+				      0xFFFFFFFF, 0);
+}
+
+static void mali_group_timeout(void *data)
+{
+	struct mali_group *group = (struct mali_group *)data;
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	MALI_DEBUG_PRINT(2, ("Group: timeout handler for %s at %u\n",
+			     mali_group_core_description(group),
+			     _mali_osk_time_tickcount()));
+
+	if (NULL != group->gp_core) {
+		mali_group_schedule_bottom_half_gp(group);
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+		mali_group_schedule_bottom_half_pp(group);
+	}
+}
+
+mali_bool mali_group_zap_session(struct mali_group *group,
+				 struct mali_session_data *session)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	if (group->session != session) {
+		/* not running from this session */
+		return MALI_TRUE; /* success */
+	}
+
+	if (group->is_working) {
+		/* The Zap also does the stall and disable_stall */
+		mali_bool zap_success = mali_mmu_zap_tlb(group->mmu);
+		return zap_success;
+	} else {
+		/* Just remove the session instead of zapping */
+		mali_group_clear_session(group);
+		return MALI_TRUE; /* success */
+	}
+}
+
+#if defined(CONFIG_MALI400_PROFILING)
+static void mali_group_report_l2_cache_counters_per_core(struct mali_group *group, u32 core_num)
+{
+	u32 source0 = 0;
+	u32 value0 = 0;
+	u32 source1 = 0;
+	u32 value1 = 0;
+	u32 profiling_channel = 0;
+
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	switch (core_num) {
+	case 0:
+		profiling_channel = MALI_PROFILING_EVENT_TYPE_SINGLE |
+				    MALI_PROFILING_EVENT_CHANNEL_GPU |
+				    MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L20_COUNTERS;
+		break;
+	case 1:
+		profiling_channel = MALI_PROFILING_EVENT_TYPE_SINGLE |
+				    MALI_PROFILING_EVENT_CHANNEL_GPU |
+				    MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L21_COUNTERS;
+		break;
+	case 2:
+		profiling_channel = MALI_PROFILING_EVENT_TYPE_SINGLE |
+				    MALI_PROFILING_EVENT_CHANNEL_GPU |
+				    MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L22_COUNTERS;
+		break;
+	default:
+		profiling_channel = MALI_PROFILING_EVENT_TYPE_SINGLE |
+				    MALI_PROFILING_EVENT_CHANNEL_GPU |
+				    MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L20_COUNTERS;
+		break;
+	}
+
+	if (0 == core_num) {
+		mali_l2_cache_core_get_counter_values(group->l2_cache_core[0], &source0, &value0, &source1, &value1);
+	}
+	if (1 == core_num) {
+		if (1 == mali_l2_cache_get_id(group->l2_cache_core[0])) {
+			mali_l2_cache_core_get_counter_values(group->l2_cache_core[0], &source0, &value0, &source1, &value1);
+		} else if (1 == mali_l2_cache_get_id(group->l2_cache_core[1])) {
+			mali_l2_cache_core_get_counter_values(group->l2_cache_core[1], &source0, &value0, &source1, &value1);
+		}
+	}
+	if (2 == core_num) {
+		if (2 == mali_l2_cache_get_id(group->l2_cache_core[0])) {
+			mali_l2_cache_core_get_counter_values(group->l2_cache_core[0], &source0, &value0, &source1, &value1);
+		} else if (2 == mali_l2_cache_get_id(group->l2_cache_core[1])) {
+			mali_l2_cache_core_get_counter_values(group->l2_cache_core[1], &source0, &value0, &source1, &value1);
+		}
+	}
+
+	_mali_osk_profiling_add_event(profiling_channel, source1 << 8 | source0, value0, value1, 0, 0);
+}
+#endif /* #if defined(CONFIG_MALI400_PROFILING) */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_group.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_group.h
@@ -0,0 +1,460 @@
+/*
+ * Copyright (C) 2011-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_GROUP_H__
+#define __MALI_GROUP_H__
+
+#include "mali_osk.h"
+#include "mali_l2_cache.h"
+#include "mali_mmu.h"
+#include "mali_gp.h"
+#include "mali_pp.h"
+#include "mali_session.h"
+#include "mali_osk_profiling.h"
+
+/**
+ * @brief Default max runtime [ms] for a core job - used by timeout timers
+ */
+#define MALI_MAX_JOB_RUNTIME_DEFAULT 5000
+
+extern int mali_max_job_runtime;
+
+#define MALI_MAX_NUMBER_OF_GROUPS 10
+#define MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS 8
+
+enum mali_group_state {
+	MALI_GROUP_STATE_INACTIVE,
+	MALI_GROUP_STATE_ACTIVATION_PENDING,
+	MALI_GROUP_STATE_ACTIVE,
+};
+
+/**
+ * The structure represents a render group
+ * A render group is defined by all the cores that share the same Mali MMU
+ */
+
+struct mali_group {
+	struct mali_mmu_core        *mmu;
+	struct mali_session_data    *session;
+
+	enum mali_group_state        state;
+	mali_bool                    power_is_on;
+
+	mali_bool                    is_working;
+	unsigned long                start_time; /* in ticks */
+
+	struct mali_gp_core         *gp_core;
+	struct mali_gp_job          *gp_running_job;
+
+	struct mali_pp_core         *pp_core;
+	struct mali_pp_job          *pp_running_job;
+	u32                         pp_running_sub_job;
+
+	struct mali_pm_domain       *pm_domain;
+
+	struct mali_l2_cache_core   *l2_cache_core[2];
+	u32                         l2_cache_core_ref_count[2];
+
+	/* Parent virtual group (if any) */
+	struct mali_group           *parent_group;
+
+	struct mali_dlbu_core       *dlbu_core;
+	struct mali_bcast_unit      *bcast_core;
+
+	/* Used for working groups which needs to be disabled */
+	mali_bool                    disable_requested;
+
+	/* Used by group to link child groups (for virtual group) */
+	_mali_osk_list_t            group_list;
+
+	/* Used by executor module in order to link groups of same state */
+	_mali_osk_list_t            executor_list;
+
+	/* Used by PM domains to link groups of same domain */
+	_mali_osk_list_t             pm_domain_list;
+
+	_mali_osk_wq_work_t         *bottom_half_work_mmu;
+	_mali_osk_wq_work_t         *bottom_half_work_gp;
+	_mali_osk_wq_work_t         *bottom_half_work_pp;
+
+	_mali_osk_timer_t           *timeout_timer;
+};
+
+/** @brief Create a new Mali group object
+ *
+ * @return A pointer to a new group object
+ */
+struct mali_group *mali_group_create(struct mali_l2_cache_core *core,
+				     struct mali_dlbu_core *dlbu,
+				     struct mali_bcast_unit *bcast,
+				     u32 domain_index);
+
+void mali_group_dump_status(struct mali_group *group);
+
+void mali_group_delete(struct mali_group *group);
+
+_mali_osk_errcode_t mali_group_add_mmu_core(struct mali_group *group,
+		struct mali_mmu_core *mmu_core);
+void mali_group_remove_mmu_core(struct mali_group *group);
+
+_mali_osk_errcode_t mali_group_add_gp_core(struct mali_group *group,
+		struct mali_gp_core *gp_core);
+void mali_group_remove_gp_core(struct mali_group *group);
+
+_mali_osk_errcode_t mali_group_add_pp_core(struct mali_group *group,
+		struct mali_pp_core *pp_core);
+void mali_group_remove_pp_core(struct mali_group *group);
+
+MALI_STATIC_INLINE const char *mali_group_core_description(
+	struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	if (NULL != group->pp_core) {
+		return mali_pp_core_description(group->pp_core);
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+		return mali_gp_core_description(group->gp_core);
+	}
+}
+
+MALI_STATIC_INLINE mali_bool mali_group_is_virtual(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+#if (defined(CONFIG_MALI450) || defined(CONFIG_MALI470))
+	return (NULL != group->dlbu_core);
+#else
+	return MALI_FALSE;
+#endif
+}
+
+/** @brief Check if a group is a part of a virtual group or not
+ */
+MALI_STATIC_INLINE mali_bool mali_group_is_in_virtual(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+#if (defined(CONFIG_MALI450) || defined(CONFIG_MALI470))
+	return (NULL != group->parent_group) ? MALI_TRUE : MALI_FALSE;
+#else
+	return MALI_FALSE;
+#endif
+}
+
+/** @brief Reset group
+ *
+ * This function will reset the entire group,
+ * including all the cores present in the group.
+ *
+ * @param group Pointer to the group to reset
+ */
+void mali_group_reset(struct mali_group *group);
+
+MALI_STATIC_INLINE struct mali_session_data *mali_group_get_session(
+	struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	return group->session;
+}
+
+MALI_STATIC_INLINE void mali_group_clear_session(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	if (NULL != group->session) {
+		mali_mmu_activate_empty_page_directory(group->mmu);
+		group->session = NULL;
+	}
+}
+
+enum mali_group_state mali_group_activate(struct mali_group *group);
+
+/*
+ * Change state from ACTIVATION_PENDING to ACTIVE
+ * For virtual group, all childs need to be ACTIVE first
+ */
+mali_bool mali_group_set_active(struct mali_group *group);
+
+/*
+ * @return MALI_TRUE means one or more domains can now be powered off,
+ * and caller should call either mali_pm_update_async() or
+ * mali_pm_update_sync() in order to do so.
+ */
+mali_bool mali_group_deactivate(struct mali_group *group);
+
+MALI_STATIC_INLINE enum mali_group_state mali_group_get_state(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return group->state;
+}
+
+MALI_STATIC_INLINE mali_bool mali_group_power_is_on(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	return group->power_is_on;
+}
+
+void mali_group_power_up(struct mali_group *group);
+void mali_group_power_down(struct mali_group *group);
+
+MALI_STATIC_INLINE void mali_group_set_disable_request(
+	struct mali_group *group, mali_bool disable)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	group->disable_requested = disable;
+
+	/**
+	 * When one of child group's disable_requeset is set TRUE, then
+	 * the disable_request of parent group should also be set to TRUE.
+	 * While, the disable_request of parent group should only be set to FALSE
+	 * only when all of its child group's disable_request are set to FALSE.
+	 */
+	if (NULL != group->parent_group && MALI_TRUE == disable) {
+		group->parent_group->disable_requested = disable;
+	}
+}
+
+MALI_STATIC_INLINE mali_bool mali_group_disable_requested(
+	struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return group->disable_requested;
+}
+
+/** @brief Virtual groups */
+void mali_group_add_group(struct mali_group *parent, struct mali_group *child);
+struct mali_group *mali_group_acquire_group(struct mali_group *parent);
+void mali_group_remove_group(struct mali_group *parent, struct mali_group *child);
+
+/** @brief Checks if the group is working.
+ */
+MALI_STATIC_INLINE mali_bool mali_group_is_working(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	if (mali_group_is_in_virtual(group)) {
+		struct mali_group *tmp_group = mali_executor_get_virtual_group();
+		return tmp_group->is_working;
+	}
+	return group->is_working;
+}
+
+MALI_STATIC_INLINE struct mali_gp_job *mali_group_get_running_gp_job(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return group->gp_running_job;
+}
+
+/** @brief Zap MMU TLB on all groups
+ *
+ * Zap TLB on group if \a session is active.
+ */
+mali_bool mali_group_zap_session(struct mali_group *group,
+				 struct mali_session_data *session);
+
+/** @brief Get pointer to GP core object
+ */
+MALI_STATIC_INLINE struct mali_gp_core *mali_group_get_gp_core(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	return group->gp_core;
+}
+
+/** @brief Get pointer to PP core object
+ */
+MALI_STATIC_INLINE struct mali_pp_core *mali_group_get_pp_core(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	return group->pp_core;
+}
+
+/** @brief Start GP job
+ */
+void mali_group_start_gp_job(struct mali_group *group, struct mali_gp_job *job, mali_bool gpu_secure_mode_pre_enabled);
+
+void mali_group_start_pp_job(struct mali_group *group, struct mali_pp_job *job, u32 sub_job, mali_bool gpu_secure_mode_pre_enabled);
+
+/** @brief Start virtual group Job on a virtual group
+*/
+void mali_group_start_job_on_virtual(struct mali_group *group, struct mali_pp_job *job, u32 first_subjob, u32 last_subjob);
+
+
+/** @brief Start a subjob from a particular on a specific PP group
+*/
+void mali_group_start_job_on_group(struct mali_group *group, struct mali_pp_job *job, u32 subjob);
+
+
+/** @brief remove all the unused groups in tmp_unused group  list, so that the group is in consistent status.
+ */
+void mali_group_non_dlbu_job_done_virtual(struct mali_group *group);
+
+
+/** @brief Resume GP job that suspended waiting for more heap memory
+ */
+void mali_group_resume_gp_with_new_heap(struct mali_group *group, u32 job_id, u32 start_addr, u32 end_addr);
+
+MALI_STATIC_INLINE enum mali_interrupt_result mali_group_get_interrupt_result_gp(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_gp_get_interrupt_result(group->gp_core);
+}
+
+MALI_STATIC_INLINE enum mali_interrupt_result mali_group_get_interrupt_result_pp(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_pp_get_interrupt_result(group->pp_core);
+}
+
+MALI_STATIC_INLINE enum mali_interrupt_result mali_group_get_interrupt_result_mmu(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_mmu_get_interrupt_result(group->mmu);
+}
+
+MALI_STATIC_INLINE mali_bool mali_group_gp_is_active(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_gp_is_active(group->gp_core);
+}
+
+MALI_STATIC_INLINE mali_bool mali_group_pp_is_active(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_pp_is_active(group->pp_core);
+}
+
+MALI_STATIC_INLINE mali_bool mali_group_has_timed_out(struct mali_group *group)
+{
+	unsigned long time_cost;
+	struct mali_group *tmp_group = group;
+
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+
+	/* if the group is in virtual need to use virtual_group's start time */
+	if (mali_group_is_in_virtual(group)) {
+		tmp_group = mali_executor_get_virtual_group();
+	}
+
+	time_cost = _mali_osk_time_tickcount() - tmp_group->start_time;
+	if (_mali_osk_time_mstoticks(mali_max_job_runtime) <= time_cost) {
+		/*
+		 * current tick is at or after timeout end time,
+		 * so this is a valid timeout
+		 */
+		return MALI_TRUE;
+	} else {
+		/*
+		 * Not a valid timeout. A HW interrupt probably beat
+		 * us to it, and the timer wasn't properly deleted
+		 * (async deletion used due to atomic context).
+		 */
+		return MALI_FALSE;
+	}
+}
+
+MALI_STATIC_INLINE void mali_group_mask_all_interrupts_gp(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_gp_mask_all_interrupts(group->gp_core);
+}
+
+MALI_STATIC_INLINE void mali_group_mask_all_interrupts_pp(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return mali_pp_mask_all_interrupts(group->pp_core);
+}
+
+MALI_STATIC_INLINE void mali_group_enable_interrupts_gp(
+	struct mali_group *group,
+	enum mali_interrupt_result exceptions)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	mali_gp_enable_interrupts(group->gp_core, exceptions);
+}
+
+MALI_STATIC_INLINE void mali_group_schedule_bottom_half_gp(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->gp_core);
+	_mali_osk_wq_schedule_work(group->bottom_half_work_gp);
+}
+
+
+MALI_STATIC_INLINE void mali_group_schedule_bottom_half_pp(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->pp_core);
+	_mali_osk_wq_schedule_work(group->bottom_half_work_pp);
+}
+
+MALI_STATIC_INLINE void mali_group_schedule_bottom_half_mmu(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT_POINTER(group->mmu);
+	_mali_osk_wq_schedule_work(group->bottom_half_work_mmu);
+}
+
+struct mali_pp_job *mali_group_complete_pp(struct mali_group *group, mali_bool success, u32 *sub_job);
+
+struct mali_gp_job *mali_group_complete_gp(struct mali_group *group, mali_bool success);
+
+#if defined(CONFIG_MALI400_PROFILING)
+MALI_STATIC_INLINE void mali_group_oom(struct mali_group *group)
+{
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SUSPEND |
+				      MALI_PROFILING_MAKE_EVENT_CHANNEL_GP(0),
+				      0, 0, 0, 0, 0);
+}
+#endif
+
+struct mali_group *mali_group_get_glob_group(u32 index);
+u32 mali_group_get_glob_num_groups(void);
+
+u32 mali_group_dump_state(struct mali_group *group, char *buf, u32 size);
+
+
+_mali_osk_errcode_t mali_group_upper_half_mmu(void *data);
+_mali_osk_errcode_t mali_group_upper_half_gp(void *data);
+_mali_osk_errcode_t mali_group_upper_half_pp(void *data);
+
+MALI_STATIC_INLINE mali_bool mali_group_is_empty(struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(group);
+	MALI_DEBUG_ASSERT(mali_group_is_virtual(group));
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	return _mali_osk_list_empty(&group->group_list);
+}
+
+#endif /* __MALI_GROUP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_hw_core.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_hw_core.c
@@ -0,0 +1,47 @@
+/*
+ * Copyright (C) 2011-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_hw_core.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_osk_mali.h"
+
+_mali_osk_errcode_t mali_hw_core_create(struct mali_hw_core *core, const _mali_osk_resource_t *resource, u32 reg_size)
+{
+	core->phys_addr = resource->base;
+	core->phys_offset = resource->base - _mali_osk_resource_base_address();
+	core->description = resource->description;
+	core->size = reg_size;
+
+	MALI_DEBUG_ASSERT(core->phys_offset < core->phys_addr);
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_mem_reqregion(core->phys_addr, core->size, core->description)) {
+		core->mapped_registers = _mali_osk_mem_mapioregion(core->phys_addr, core->size, core->description);
+		if (NULL != core->mapped_registers) {
+			return _MALI_OSK_ERR_OK;
+		} else {
+			MALI_PRINT_ERROR(("Failed to map memory region for core %s at phys_addr 0x%08X\n", core->description, core->phys_addr));
+		}
+		_mali_osk_mem_unreqregion(core->phys_addr, core->size);
+	} else {
+		MALI_PRINT_ERROR(("Failed to request memory region for core %s at phys_addr 0x%08X\n", core->description, core->phys_addr));
+	}
+
+	return _MALI_OSK_ERR_FAULT;
+}
+
+void mali_hw_core_delete(struct mali_hw_core *core)
+{
+	if (NULL != core->mapped_registers) {
+		_mali_osk_mem_unmapioregion(core->phys_addr, core->size, core->mapped_registers);
+		core->mapped_registers = NULL;
+	}
+	_mali_osk_mem_unreqregion(core->phys_addr, core->size);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_hw_core.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_hw_core.h
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_HW_CORE_H__
+#define __MALI_HW_CORE_H__
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+/**
+ * The common parts for all Mali HW cores (GP, PP, MMU, L2 and PMU)
+ * This struct is embedded inside all core specific structs.
+ */
+struct mali_hw_core {
+	uintptr_t phys_addr;              /**< Physical address of the registers */
+	u32 phys_offset;                  /**< Offset from start of Mali to registers */
+	u32 size;                         /**< Size of registers */
+	mali_io_address mapped_registers; /**< Virtual mapping of the registers */
+	const char *description;          /**< Name of unit (as specified in device configuration) */
+};
+
+#define MALI_REG_POLL_COUNT_FAST 1000000
+#define MALI_REG_POLL_COUNT_SLOW 1000000
+
+/*
+ * GP and PP core translate their int_stat/rawstat into one of these
+ */
+enum mali_interrupt_result {
+	MALI_INTERRUPT_RESULT_NONE,
+	MALI_INTERRUPT_RESULT_SUCCESS,
+	MALI_INTERRUPT_RESULT_SUCCESS_VS,
+	MALI_INTERRUPT_RESULT_SUCCESS_PLBU,
+	MALI_INTERRUPT_RESULT_OOM,
+	MALI_INTERRUPT_RESULT_ERROR
+};
+
+_mali_osk_errcode_t mali_hw_core_create(struct mali_hw_core *core, const _mali_osk_resource_t *resource, u32 reg_size);
+void mali_hw_core_delete(struct mali_hw_core *core);
+
+MALI_STATIC_INLINE u32 mali_hw_core_register_read(struct mali_hw_core *core, u32 relative_address)
+{
+	u32 read_val;
+	read_val = _mali_osk_mem_ioread32(core->mapped_registers, relative_address);
+	MALI_DEBUG_PRINT(6, ("register_read for core %s, relative addr=0x%04X, val=0x%08X\n",
+			     core->description, relative_address, read_val));
+	return read_val;
+}
+
+MALI_STATIC_INLINE void mali_hw_core_register_write_relaxed(struct mali_hw_core *core, u32 relative_address, u32 new_val)
+{
+	MALI_DEBUG_PRINT(6, ("register_write_relaxed for core %s, relative addr=0x%04X, val=0x%08X\n",
+			     core->description, relative_address, new_val));
+	_mali_osk_mem_iowrite32_relaxed(core->mapped_registers, relative_address, new_val);
+}
+
+/* Conditionally write a register.
+ * The register will only be written if the new value is different from the old_value.
+ * If the new value is different, the old value will also be updated */
+MALI_STATIC_INLINE void mali_hw_core_register_write_relaxed_conditional(struct mali_hw_core *core, u32 relative_address, u32 new_val, const u32 old_val)
+{
+	MALI_DEBUG_PRINT(6, ("register_write_relaxed for core %s, relative addr=0x%04X, val=0x%08X\n",
+			     core->description, relative_address, new_val));
+	if (old_val != new_val) {
+		_mali_osk_mem_iowrite32_relaxed(core->mapped_registers, relative_address, new_val);
+	}
+}
+
+MALI_STATIC_INLINE void mali_hw_core_register_write(struct mali_hw_core *core, u32 relative_address, u32 new_val)
+{
+	MALI_DEBUG_PRINT(6, ("register_write for core %s, relative addr=0x%04X, val=0x%08X\n",
+			     core->description, relative_address, new_val));
+	_mali_osk_mem_iowrite32(core->mapped_registers, relative_address, new_val);
+}
+
+MALI_STATIC_INLINE void mali_hw_core_register_write_array_relaxed(struct mali_hw_core *core, u32 relative_address, u32 *write_array, u32 nr_of_regs)
+{
+	u32 i;
+	MALI_DEBUG_PRINT(6, ("register_write_array: for core %s, relative addr=0x%04X, nr of regs=%u\n",
+			     core->description, relative_address, nr_of_regs));
+
+	/* Do not use burst writes against the registers */
+	for (i = 0; i < nr_of_regs; i++) {
+		mali_hw_core_register_write_relaxed(core, relative_address + i * 4, write_array[i]);
+	}
+}
+
+/* Conditionally write a set of registers.
+ * The register will only be written if the new value is different from the old_value.
+ * If the new value is different, the old value will also be updated */
+MALI_STATIC_INLINE void mali_hw_core_register_write_array_relaxed_conditional(struct mali_hw_core *core, u32 relative_address, u32 *write_array, u32 nr_of_regs, const u32 *old_array)
+{
+	u32 i;
+	MALI_DEBUG_PRINT(6, ("register_write_array: for core %s, relative addr=0x%04X, nr of regs=%u\n",
+			     core->description, relative_address, nr_of_regs));
+
+	/* Do not use burst writes against the registers */
+	for (i = 0; i < nr_of_regs; i++) {
+		if (old_array[i] != write_array[i]) {
+			mali_hw_core_register_write_relaxed(core, relative_address + i * 4, write_array[i]);
+		}
+	}
+}
+
+#endif /* __MALI_HW_CORE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_kernel_common.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_kernel_common.h
@@ -0,0 +1,181 @@
+/*
+ * Copyright (C) 2010, 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_KERNEL_COMMON_H__
+#define __MALI_KERNEL_COMMON_H__
+
+#include "mali_osk.h"
+
+/* Make sure debug is defined when it should be */
+#ifndef DEBUG
+#if defined(_DEBUG)
+#define DEBUG
+#endif
+#endif
+
+/* The file include several useful macros for error checking, debugging and printing.
+ * - MALI_PRINTF(...)           Do not use this function: Will be included in Release builds.
+ * - MALI_DEBUG_PRINT(nr, (X) ) Prints the second argument if nr<=MALI_DEBUG_LEVEL.
+ * - MALI_DEBUG_ERROR( (X) )    Prints an errortext, a source trace, and the given error message.
+ * - MALI_DEBUG_ASSERT(exp,(X)) If the asserted expr is false, the program will exit.
+ * - MALI_DEBUG_ASSERT_POINTER(pointer)  Triggers if the pointer is a zero pointer.
+ * - MALI_DEBUG_CODE( X )       The code inside the macro is only compiled in Debug builds.
+ *
+ * The (X) means that you must add an extra parenthesis around the argumentlist.
+ *
+ * The  printf function: MALI_PRINTF(...) is routed to _mali_osk_debugmsg
+ *
+ * Suggested range for the DEBUG-LEVEL is [1:6] where
+ * [1:2] Is messages with highest priority, indicate possible errors.
+ * [3:4] Is messages with medium priority, output important variables.
+ * [5:6] Is messages with low priority, used during extensive debugging.
+ */
+
+/**
+*  Fundamental error macro. Reports an error code. This is abstracted to allow us to
+*  easily switch to a different error reporting method if we want, and also to allow
+*  us to search for error returns easily.
+*
+*  Note no closing semicolon - this is supplied in typical usage:
+*
+*  MALI_ERROR(MALI_ERROR_OUT_OF_MEMORY);
+*/
+#define MALI_ERROR(error_code) return (error_code)
+
+/**
+ *  Basic error macro, to indicate success.
+ *  Note no closing semicolon - this is supplied in typical usage:
+ *
+ *  MALI_SUCCESS;
+ */
+#define MALI_SUCCESS MALI_ERROR(_MALI_OSK_ERR_OK)
+
+/**
+ *  Basic error macro. This checks whether the given condition is true, and if not returns
+ *  from this function with the supplied error code. This is a macro so that we can override it
+ *  for stress testing.
+ *
+ *  Note that this uses the do-while-0 wrapping to ensure that we don't get problems with dangling
+ *  else clauses. Note also no closing semicolon - this is supplied in typical usage:
+ *
+ *  MALI_CHECK((p!=NULL), ERROR_NO_OBJECT);
+ */
+#define MALI_CHECK(condition, error_code) do { if(!(condition)) MALI_ERROR(error_code); } while(0)
+
+/**
+ *  Error propagation macro. If the expression given is anything other than
+ *  _MALI_OSK_NO_ERROR, then the value is returned from the enclosing function
+ *  as an error code. This effectively acts as a guard clause, and propagates
+ *  error values up the call stack. This uses a temporary value to ensure that
+ *  the error expression is not evaluated twice.
+ *  If the counter for forcing a failure has been set using _mali_force_error,
+ *  this error will be returned without evaluating the expression in
+ *  MALI_CHECK_NO_ERROR
+ */
+#define MALI_CHECK_NO_ERROR(expression) \
+	do { _mali_osk_errcode_t _check_no_error_result=(expression); \
+		if(_check_no_error_result != _MALI_OSK_ERR_OK) \
+			MALI_ERROR(_check_no_error_result); \
+	} while(0)
+
+/**
+ *  Pointer check macro. Checks non-null pointer.
+ */
+#define MALI_CHECK_NON_NULL(pointer, error_code) MALI_CHECK( ((pointer)!=NULL), (error_code) )
+
+/**
+ *  Error macro with goto. This checks whether the given condition is true, and if not jumps
+ *  to the specified label using a goto. The label must therefore be local to the function in
+ *  which this macro appears. This is most usually used to execute some clean-up code before
+ *  exiting with a call to ERROR.
+ *
+ *  Like the other macros, this is a macro to allow us to override the condition if we wish,
+ *  e.g. to force an error during stress testing.
+ */
+#define MALI_CHECK_GOTO(condition, label) do { if(!(condition)) goto label; } while(0)
+
+/**
+ *  Explicitly ignore a parameter passed into a function, to suppress compiler warnings.
+ *  Should only be used with parameter names.
+ */
+#define MALI_IGNORE(x) x=x
+
+#if defined(CONFIG_MALI_QUIET)
+#define MALI_PRINTF(args)
+#else
+#define MALI_PRINTF(args) _mali_osk_dbgmsg args;
+#endif
+
+#define MALI_PRINT_ERROR(args) do{ \
+		MALI_PRINTF(("Mali: ERR: %s\n" ,__FILE__)); \
+		MALI_PRINTF(("           %s()%4d\n           ", __FUNCTION__, __LINE__)) ; \
+		MALI_PRINTF(args); \
+		MALI_PRINTF(("\n")); \
+	} while(0)
+
+#define MALI_PRINT(args) do{ \
+		MALI_PRINTF(("Mali: ")); \
+		MALI_PRINTF(args); \
+	} while (0)
+
+#ifdef DEBUG
+#ifndef mali_debug_level
+extern int mali_debug_level;
+#endif
+
+#define MALI_DEBUG_CODE(code) code
+#define MALI_DEBUG_PRINT(level, args)  do { \
+		if((level) <=  mali_debug_level)\
+		{MALI_PRINTF(("Mali<" #level ">: ")); MALI_PRINTF(args); } \
+	} while (0)
+
+#define MALI_DEBUG_PRINT_ERROR(args) MALI_PRINT_ERROR(args)
+
+#define MALI_DEBUG_PRINT_IF(level,condition,args)  \
+	if((condition)&&((level) <=  mali_debug_level))\
+	{MALI_PRINTF(("Mali<" #level ">: ")); MALI_PRINTF(args); }
+
+#define MALI_DEBUG_PRINT_ELSE(level, args)\
+	else if((level) <=  mali_debug_level)\
+	{ MALI_PRINTF(("Mali<" #level ">: ")); MALI_PRINTF(args); }
+
+/**
+ * @note these variants of DEBUG ASSERTS will cause a debugger breakpoint
+ * to be entered (see _mali_osk_break() ). An alternative would be to call
+ * _mali_osk_abort(), on OSs that support it.
+ */
+#define MALI_DEBUG_PRINT_ASSERT(condition, args) do  {if( !(condition)) { MALI_PRINT_ERROR(args); _mali_osk_break(); } } while(0)
+#define MALI_DEBUG_ASSERT_POINTER(pointer) do  {if( (pointer)== NULL) {MALI_PRINT_ERROR(("NULL pointer " #pointer)); _mali_osk_break();} } while(0)
+#define MALI_DEBUG_ASSERT(condition) do  {if( !(condition)) {MALI_PRINT_ERROR(("ASSERT failed: " #condition )); _mali_osk_break();} } while(0)
+
+#else /* DEBUG */
+
+#define MALI_DEBUG_CODE(code)
+#define MALI_DEBUG_PRINT(string,args) do {} while(0)
+#define MALI_DEBUG_PRINT_ERROR(args) do {} while(0)
+#define MALI_DEBUG_PRINT_IF(level,condition,args) do {} while(0)
+#define MALI_DEBUG_PRINT_ELSE(level,condition,args) do {} while(0)
+#define MALI_DEBUG_PRINT_ASSERT(condition,args) do {} while(0)
+#define MALI_DEBUG_ASSERT_POINTER(pointer) do {} while(0)
+#define MALI_DEBUG_ASSERT(condition) do {} while(0)
+
+#endif /* DEBUG */
+
+/**
+ * variables from user space cannot be dereferenced from kernel space; tagging them
+ * with __user allows the GCC compiler to generate a warning. Other compilers may
+ * not support this so we define it here as an empty macro if the compiler doesn't
+ * define it.
+ */
+#ifndef __user
+#define __user
+#endif
+
+#endif /* __MALI_KERNEL_COMMON_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_kernel_core.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_kernel_core.c
@@ -0,0 +1,1349 @@
+/*
+ * Copyright (C) 2010-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_ukk.h"
+#include "mali_kernel_core.h"
+#include "mali_memory.h"
+#include "mali_mem_validation.h"
+#include "mali_mmu.h"
+#include "mali_mmu_page_directory.h"
+#include "mali_dlbu.h"
+#include "mali_broadcast.h"
+#include "mali_gp.h"
+#include "mali_pp.h"
+#include "mali_executor.h"
+#include "mali_pp_job.h"
+#include "mali_group.h"
+#include "mali_pm.h"
+#include "mali_pmu.h"
+#include "mali_scheduler.h"
+#include "mali_kernel_utilization.h"
+#include "mali_l2_cache.h"
+#include "mali_timeline.h"
+#include "mali_soft_job.h"
+#include "mali_pm_domain.h"
+#if defined(CONFIG_MALI400_PROFILING)
+#include "mali_osk_profiling.h"
+#endif
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+#include "mali_profiling_internal.h"
+#endif
+#include "mali_control_timer.h"
+#include "mali_dvfs_policy.h"
+#include <linux/sched.h>
+#include <linux/atomic.h>
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+#include <linux/dma-fence.h>
+#else
+#include <linux/fence.h>
+#endif
+#endif
+
+#define MALI_SHARED_MEMORY_DEFAULT_SIZE 0xffffffff
+
+/* Mali GPU memory. Real values come from module parameter or from device specific data */
+unsigned int mali_dedicated_mem_start = 0;
+unsigned int mali_dedicated_mem_size = 0;
+
+/* Default shared memory size is set to 4G. */
+unsigned int mali_shared_mem_size = MALI_SHARED_MEMORY_DEFAULT_SIZE;
+
+/* Frame buffer memory to be accessible by Mali GPU */
+int mali_fb_start = 0;
+int mali_fb_size = 0;
+
+/* Mali max job runtime */
+extern int mali_max_job_runtime;
+
+/** Start profiling from module load? */
+int mali_boot_profiling = 0;
+
+/** Limits for the number of PP cores behind each L2 cache. */
+int mali_max_pp_cores_group_1 = 0xFF;
+int mali_max_pp_cores_group_2 = 0xFF;
+
+int mali_inited_pp_cores_group_1 = 0;
+int mali_inited_pp_cores_group_2 = 0;
+
+static _mali_product_id_t global_product_id = _MALI_PRODUCT_ID_UNKNOWN;
+static uintptr_t global_gpu_base_address = 0;
+static u32 global_gpu_major_version = 0;
+static u32 global_gpu_minor_version = 0;
+
+mali_bool mali_gpu_class_is_mali450 = MALI_FALSE;
+mali_bool mali_gpu_class_is_mali470 = MALI_FALSE;
+
+static _mali_osk_errcode_t mali_set_global_gpu_base_address(void)
+{
+	_mali_osk_errcode_t err = _MALI_OSK_ERR_OK;
+
+	global_gpu_base_address = _mali_osk_resource_base_address();
+	if (0 == global_gpu_base_address) {
+		err = _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	}
+
+	return err;
+}
+
+static u32 mali_get_bcast_id(_mali_osk_resource_t *resource_pp)
+{
+	switch (resource_pp->base - global_gpu_base_address) {
+	case 0x08000:
+	case 0x20000: /* fall-through for aliased mapping */
+		return 0x01;
+	case 0x0A000:
+	case 0x22000: /* fall-through for aliased mapping */
+		return 0x02;
+	case 0x0C000:
+	case 0x24000: /* fall-through for aliased mapping */
+		return 0x04;
+	case 0x0E000:
+	case 0x26000: /* fall-through for aliased mapping */
+		return 0x08;
+	case 0x28000:
+		return 0x10;
+	case 0x2A000:
+		return 0x20;
+	case 0x2C000:
+		return 0x40;
+	case 0x2E000:
+		return 0x80;
+	default:
+		return 0;
+	}
+}
+
+static _mali_osk_errcode_t mali_parse_product_info(void)
+{
+	_mali_osk_resource_t first_pp_resource;
+
+	/* Find the first PP core resource (again) */
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI_OFFSET_PP0, &first_pp_resource)) {
+		/* Create a dummy PP object for this core so that we can read the version register */
+		struct mali_group *group = mali_group_create(NULL, NULL, NULL, MALI_DOMAIN_INDEX_PP0);
+		if (NULL != group) {
+			struct mali_pp_core *pp_core = mali_pp_create(&first_pp_resource, group, MALI_FALSE, mali_get_bcast_id(&first_pp_resource));
+			if (NULL != pp_core) {
+				u32 pp_version;
+
+				pp_version = mali_pp_core_get_version(pp_core);
+
+				mali_group_delete(group);
+
+				global_gpu_major_version = (pp_version >> 8) & 0xFF;
+				global_gpu_minor_version = pp_version & 0xFF;
+
+				switch (pp_version >> 16) {
+				case MALI200_PP_PRODUCT_ID:
+					global_product_id = _MALI_PRODUCT_ID_MALI200;
+					MALI_DEBUG_PRINT(2, ("Found Mali GPU Mali-200 r%up%u\n", global_gpu_major_version, global_gpu_minor_version));
+					MALI_PRINT_ERROR(("Mali-200 is not supported by this driver.\n"));
+					_mali_osk_abort();
+					break;
+				case MALI300_PP_PRODUCT_ID:
+					global_product_id = _MALI_PRODUCT_ID_MALI300;
+					MALI_DEBUG_PRINT(2, ("Found Mali GPU Mali-300 r%up%u\n", global_gpu_major_version, global_gpu_minor_version));
+					break;
+				case MALI400_PP_PRODUCT_ID:
+					global_product_id = _MALI_PRODUCT_ID_MALI400;
+					MALI_DEBUG_PRINT(2, ("Found Mali GPU Mali-400 MP r%up%u\n", global_gpu_major_version, global_gpu_minor_version));
+					break;
+				case MALI450_PP_PRODUCT_ID:
+					global_product_id = _MALI_PRODUCT_ID_MALI450;
+					MALI_DEBUG_PRINT(2, ("Found Mali GPU Mali-450 MP r%up%u\n", global_gpu_major_version, global_gpu_minor_version));
+					break;
+				case MALI470_PP_PRODUCT_ID:
+					global_product_id = _MALI_PRODUCT_ID_MALI470;
+					MALI_DEBUG_PRINT(2, ("Found Mali GPU Mali-470 MP r%up%u\n", global_gpu_major_version, global_gpu_minor_version));
+					break;
+				default:
+					MALI_DEBUG_PRINT(2, ("Found unknown Mali GPU (r%up%u)\n", global_gpu_major_version, global_gpu_minor_version));
+					return _MALI_OSK_ERR_FAULT;
+				}
+
+				return _MALI_OSK_ERR_OK;
+			} else {
+				MALI_PRINT_ERROR(("Failed to create initial PP object\n"));
+			}
+		} else {
+			MALI_PRINT_ERROR(("Failed to create initial group object\n"));
+		}
+	} else {
+		MALI_PRINT_ERROR(("First PP core not specified in config file\n"));
+	}
+
+	return _MALI_OSK_ERR_FAULT;
+}
+
+static void mali_delete_groups(void)
+{
+	struct mali_group *group;
+
+	group = mali_group_get_glob_group(0);
+	while (NULL != group) {
+		mali_group_delete(group);
+		group = mali_group_get_glob_group(0);
+	}
+
+	MALI_DEBUG_ASSERT(0 == mali_group_get_glob_num_groups());
+}
+
+static void mali_delete_l2_cache_cores(void)
+{
+	struct mali_l2_cache_core *l2;
+
+	l2 = mali_l2_cache_core_get_glob_l2_core(0);
+	while (NULL != l2) {
+		mali_l2_cache_delete(l2);
+		l2 = mali_l2_cache_core_get_glob_l2_core(0);
+	}
+
+	MALI_DEBUG_ASSERT(0 == mali_l2_cache_core_get_glob_num_l2_cores());
+}
+
+static struct mali_l2_cache_core *mali_create_l2_cache_core(_mali_osk_resource_t *resource, u32 domain_index)
+{
+	struct mali_l2_cache_core *l2_cache = NULL;
+
+	if (NULL != resource) {
+
+		MALI_DEBUG_PRINT(3, ("Found L2 cache %s\n", resource->description));
+
+		l2_cache = mali_l2_cache_create(resource, domain_index);
+		if (NULL == l2_cache) {
+			MALI_PRINT_ERROR(("Failed to create L2 cache object\n"));
+			return NULL;
+		}
+	}
+	MALI_DEBUG_PRINT(3, ("Created L2 cache core object\n"));
+
+	return l2_cache;
+}
+
+static _mali_osk_errcode_t mali_parse_config_l2_cache(void)
+{
+	struct mali_l2_cache_core *l2_cache = NULL;
+
+	if (mali_is_mali400()) {
+		_mali_osk_resource_t l2_resource;
+		if (_MALI_OSK_ERR_OK != _mali_osk_resource_find(MALI400_OFFSET_L2_CACHE0, &l2_resource)) {
+			MALI_DEBUG_PRINT(3, ("Did not find required Mali L2 cache in config file\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+
+		l2_cache = mali_create_l2_cache_core(&l2_resource, MALI_DOMAIN_INDEX_L20);
+		if (NULL == l2_cache) {
+			return _MALI_OSK_ERR_FAULT;
+		}
+	} else if (mali_is_mali450()) {
+		/*
+		 * L2 for GP    at 0x10000
+		 * L2 for PP0-3 at 0x01000
+		 * L2 for PP4-7 at 0x11000 (optional)
+		 */
+
+		_mali_osk_resource_t l2_gp_resource;
+		_mali_osk_resource_t l2_pp_grp0_resource;
+		_mali_osk_resource_t l2_pp_grp1_resource;
+
+		/* Make cluster for GP's L2 */
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI450_OFFSET_L2_CACHE0, &l2_gp_resource)) {
+			MALI_DEBUG_PRINT(3, ("Creating Mali-450 L2 cache core for GP\n"));
+			l2_cache = mali_create_l2_cache_core(&l2_gp_resource, MALI_DOMAIN_INDEX_L20);
+			if (NULL == l2_cache) {
+				return _MALI_OSK_ERR_FAULT;
+			}
+		} else {
+			MALI_DEBUG_PRINT(3, ("Did not find required Mali L2 cache for GP in config file\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+
+		/* Find corresponding l2 domain */
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI450_OFFSET_L2_CACHE1, &l2_pp_grp0_resource)) {
+			MALI_DEBUG_PRINT(3, ("Creating Mali-450 L2 cache core for PP group 0\n"));
+			l2_cache = mali_create_l2_cache_core(&l2_pp_grp0_resource, MALI_DOMAIN_INDEX_L21);
+			if (NULL == l2_cache) {
+				return _MALI_OSK_ERR_FAULT;
+			}
+		} else {
+			MALI_DEBUG_PRINT(3, ("Did not find required Mali L2 cache for PP group 0 in config file\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+
+		/* Second PP core group is optional, don't fail if we don't find it */
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI450_OFFSET_L2_CACHE2, &l2_pp_grp1_resource)) {
+			MALI_DEBUG_PRINT(3, ("Creating Mali-450 L2 cache core for PP group 1\n"));
+			l2_cache = mali_create_l2_cache_core(&l2_pp_grp1_resource, MALI_DOMAIN_INDEX_L22);
+			if (NULL == l2_cache) {
+				return _MALI_OSK_ERR_FAULT;
+			}
+		}
+	} else if (mali_is_mali470()) {
+		_mali_osk_resource_t l2c1_resource;
+
+		/* Make cluster for L2C1 */
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI470_OFFSET_L2_CACHE1, &l2c1_resource)) {
+			MALI_DEBUG_PRINT(3, ("Creating Mali-470 L2 cache 1\n"));
+			l2_cache = mali_create_l2_cache_core(&l2c1_resource, MALI_DOMAIN_INDEX_L21);
+			if (NULL == l2_cache) {
+				return _MALI_OSK_ERR_FAULT;
+			}
+		} else {
+			MALI_DEBUG_PRINT(3, ("Did not find required Mali L2 cache for L2C1\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static struct mali_group *mali_create_group(struct mali_l2_cache_core *cache,
+		_mali_osk_resource_t *resource_mmu,
+		_mali_osk_resource_t *resource_gp,
+		_mali_osk_resource_t *resource_pp,
+		u32 domain_index)
+{
+	struct mali_mmu_core *mmu;
+	struct mali_group *group;
+
+	MALI_DEBUG_PRINT(3, ("Starting new group for MMU %s\n", resource_mmu->description));
+
+	/* Create the group object */
+	group = mali_group_create(cache, NULL, NULL, domain_index);
+	if (NULL == group) {
+		MALI_PRINT_ERROR(("Failed to create group object for MMU %s\n", resource_mmu->description));
+		return NULL;
+	}
+
+	/* Create the MMU object inside group */
+	mmu = mali_mmu_create(resource_mmu, group, MALI_FALSE);
+	if (NULL == mmu) {
+		MALI_PRINT_ERROR(("Failed to create MMU object\n"));
+		mali_group_delete(group);
+		return NULL;
+	}
+
+	if (NULL != resource_gp) {
+		/* Create the GP core object inside this group */
+		struct mali_gp_core *gp_core = mali_gp_create(resource_gp, group);
+		if (NULL == gp_core) {
+			/* No need to clean up now, as we will clean up everything linked in from the cluster when we fail this function */
+			MALI_PRINT_ERROR(("Failed to create GP object\n"));
+			mali_group_delete(group);
+			return NULL;
+		}
+	}
+
+	if (NULL != resource_pp) {
+		struct mali_pp_core *pp_core;
+
+		/* Create the PP core object inside this group */
+		pp_core = mali_pp_create(resource_pp, group, MALI_FALSE, mali_get_bcast_id(resource_pp));
+		if (NULL == pp_core) {
+			/* No need to clean up now, as we will clean up everything linked in from the cluster when we fail this function */
+			MALI_PRINT_ERROR(("Failed to create PP object\n"));
+			mali_group_delete(group);
+			return NULL;
+		}
+	}
+
+	return group;
+}
+
+static _mali_osk_errcode_t mali_create_virtual_group(_mali_osk_resource_t *resource_mmu_pp_bcast,
+		_mali_osk_resource_t *resource_pp_bcast,
+		_mali_osk_resource_t *resource_dlbu,
+		_mali_osk_resource_t *resource_bcast)
+{
+	struct mali_mmu_core *mmu_pp_bcast_core;
+	struct mali_pp_core *pp_bcast_core;
+	struct mali_dlbu_core *dlbu_core;
+	struct mali_bcast_unit *bcast_core;
+	struct mali_group *group;
+
+	MALI_DEBUG_PRINT(2, ("Starting new virtual group for MMU PP broadcast core %s\n", resource_mmu_pp_bcast->description));
+
+	/* Create the DLBU core object */
+	dlbu_core = mali_dlbu_create(resource_dlbu);
+	if (NULL == dlbu_core) {
+		MALI_PRINT_ERROR(("Failed to create DLBU object \n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Create the Broadcast unit core */
+	bcast_core = mali_bcast_unit_create(resource_bcast);
+	if (NULL == bcast_core) {
+		MALI_PRINT_ERROR(("Failed to create Broadcast unit object!\n"));
+		mali_dlbu_delete(dlbu_core);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Create the group object */
+#if defined(DEBUG)
+	/* Get a physical PP group to temporarily add to broadcast unit.  IRQ
+	 * verification needs a physical group in the broadcast unit to test
+	 * the broadcast unit interrupt line. */
+	{
+		struct mali_group *phys_group = NULL;
+		int i;
+		for (i = 0; i < mali_group_get_glob_num_groups(); i++) {
+			phys_group = mali_group_get_glob_group(i);
+			if (NULL != mali_group_get_pp_core(phys_group)) break;
+		}
+		MALI_DEBUG_ASSERT(NULL != mali_group_get_pp_core(phys_group));
+
+		/* Add the group temporarily to the broadcast, and update the
+		 * broadcast HW. Since the HW is not updated when removing the
+		 * group the IRQ check will work when the virtual PP is created
+		 * later.
+		 *
+		 * When the virtual group gets populated, the actually used
+		 * groups will be added to the broadcast unit and the HW will
+		 * be updated.
+		 */
+		mali_bcast_add_group(bcast_core, phys_group);
+		mali_bcast_reset(bcast_core);
+		mali_bcast_remove_group(bcast_core, phys_group);
+	}
+#endif /* DEBUG */
+	group = mali_group_create(NULL, dlbu_core, bcast_core, MALI_DOMAIN_INDEX_DUMMY);
+	if (NULL == group) {
+		MALI_PRINT_ERROR(("Failed to create group object for MMU PP broadcast core %s\n", resource_mmu_pp_bcast->description));
+		mali_bcast_unit_delete(bcast_core);
+		mali_dlbu_delete(dlbu_core);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Create the MMU object inside group */
+	mmu_pp_bcast_core = mali_mmu_create(resource_mmu_pp_bcast, group, MALI_TRUE);
+	if (NULL == mmu_pp_bcast_core) {
+		MALI_PRINT_ERROR(("Failed to create MMU PP broadcast object\n"));
+		mali_group_delete(group);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Create the PP core object inside this group */
+	pp_bcast_core = mali_pp_create(resource_pp_bcast, group, MALI_TRUE, 0);
+	if (NULL == pp_bcast_core) {
+		/* No need to clean up now, as we will clean up everything linked in from the cluster when we fail this function */
+		MALI_PRINT_ERROR(("Failed to create PP object\n"));
+		mali_group_delete(group);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static _mali_osk_errcode_t mali_parse_config_groups(void)
+{
+	struct mali_group *group;
+	int cluster_id_gp = 0;
+	int cluster_id_pp_grp0 = 0;
+	int cluster_id_pp_grp1 = 0;
+	int i;
+
+	_mali_osk_resource_t resource_gp;
+	_mali_osk_resource_t resource_gp_mmu;
+	_mali_osk_resource_t resource_pp[8];
+	_mali_osk_resource_t resource_pp_mmu[8];
+	_mali_osk_resource_t resource_pp_mmu_bcast;
+	_mali_osk_resource_t resource_pp_bcast;
+	_mali_osk_resource_t resource_dlbu;
+	_mali_osk_resource_t resource_bcast;
+	_mali_osk_errcode_t resource_gp_found;
+	_mali_osk_errcode_t resource_gp_mmu_found;
+	_mali_osk_errcode_t resource_pp_found[8];
+	_mali_osk_errcode_t resource_pp_mmu_found[8];
+	_mali_osk_errcode_t resource_pp_mmu_bcast_found;
+	_mali_osk_errcode_t resource_pp_bcast_found;
+	_mali_osk_errcode_t resource_dlbu_found;
+	_mali_osk_errcode_t resource_bcast_found;
+
+	if (!(mali_is_mali400() || mali_is_mali450() || mali_is_mali470())) {
+		/* No known HW core */
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	if (MALI_MAX_JOB_RUNTIME_DEFAULT == mali_max_job_runtime) {
+		/* Group settings are not overridden by module parameters, so use device settings */
+		_mali_osk_device_data data = { 0, };
+
+		if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+			/* Use device specific settings (if defined) */
+			if (0 != data.max_job_runtime) {
+				mali_max_job_runtime = data.max_job_runtime;
+			}
+		}
+	}
+
+	if (mali_is_mali450()) {
+		/* Mali-450 have separate L2s for GP, and PP core group(s) */
+		cluster_id_pp_grp0 = 1;
+		cluster_id_pp_grp1 = 2;
+	}
+
+	resource_gp_found = _mali_osk_resource_find(MALI_OFFSET_GP, &resource_gp);
+	resource_gp_mmu_found = _mali_osk_resource_find(MALI_OFFSET_GP_MMU, &resource_gp_mmu);
+	resource_pp_found[0] = _mali_osk_resource_find(MALI_OFFSET_PP0, &(resource_pp[0]));
+	resource_pp_found[1] = _mali_osk_resource_find(MALI_OFFSET_PP1, &(resource_pp[1]));
+	resource_pp_found[2] = _mali_osk_resource_find(MALI_OFFSET_PP2, &(resource_pp[2]));
+	resource_pp_found[3] = _mali_osk_resource_find(MALI_OFFSET_PP3, &(resource_pp[3]));
+	resource_pp_found[4] = _mali_osk_resource_find(MALI_OFFSET_PP4, &(resource_pp[4]));
+	resource_pp_found[5] = _mali_osk_resource_find(MALI_OFFSET_PP5, &(resource_pp[5]));
+	resource_pp_found[6] = _mali_osk_resource_find(MALI_OFFSET_PP6, &(resource_pp[6]));
+	resource_pp_found[7] = _mali_osk_resource_find(MALI_OFFSET_PP7, &(resource_pp[7]));
+	resource_pp_mmu_found[0] = _mali_osk_resource_find(MALI_OFFSET_PP0_MMU, &(resource_pp_mmu[0]));
+	resource_pp_mmu_found[1] = _mali_osk_resource_find(MALI_OFFSET_PP1_MMU, &(resource_pp_mmu[1]));
+	resource_pp_mmu_found[2] = _mali_osk_resource_find(MALI_OFFSET_PP2_MMU, &(resource_pp_mmu[2]));
+	resource_pp_mmu_found[3] = _mali_osk_resource_find(MALI_OFFSET_PP3_MMU, &(resource_pp_mmu[3]));
+	resource_pp_mmu_found[4] = _mali_osk_resource_find(MALI_OFFSET_PP4_MMU, &(resource_pp_mmu[4]));
+	resource_pp_mmu_found[5] = _mali_osk_resource_find(MALI_OFFSET_PP5_MMU, &(resource_pp_mmu[5]));
+	resource_pp_mmu_found[6] = _mali_osk_resource_find(MALI_OFFSET_PP6_MMU, &(resource_pp_mmu[6]));
+	resource_pp_mmu_found[7] = _mali_osk_resource_find(MALI_OFFSET_PP7_MMU, &(resource_pp_mmu[7]));
+
+
+	if (mali_is_mali450() || mali_is_mali470()) {
+		resource_bcast_found = _mali_osk_resource_find(MALI_OFFSET_BCAST, &resource_bcast);
+		resource_dlbu_found = _mali_osk_resource_find(MALI_OFFSET_DLBU, &resource_dlbu);
+		resource_pp_mmu_bcast_found = _mali_osk_resource_find(MALI_OFFSET_PP_BCAST_MMU, &resource_pp_mmu_bcast);
+		resource_pp_bcast_found = _mali_osk_resource_find(MALI_OFFSET_PP_BCAST, &resource_pp_bcast);
+
+		if (_MALI_OSK_ERR_OK != resource_bcast_found ||
+		    _MALI_OSK_ERR_OK != resource_dlbu_found ||
+		    _MALI_OSK_ERR_OK != resource_pp_mmu_bcast_found ||
+		    _MALI_OSK_ERR_OK != resource_pp_bcast_found) {
+			/* Missing mandatory core(s) for Mali-450 or Mali-470 */
+			MALI_DEBUG_PRINT(2, ("Missing mandatory resources, Mali-450 needs DLBU, Broadcast unit, virtual PP core and virtual MMU\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+
+	if (_MALI_OSK_ERR_OK != resource_gp_found ||
+	    _MALI_OSK_ERR_OK != resource_gp_mmu_found ||
+	    _MALI_OSK_ERR_OK != resource_pp_found[0] ||
+	    _MALI_OSK_ERR_OK != resource_pp_mmu_found[0]) {
+		/* Missing mandatory core(s) */
+		MALI_DEBUG_PRINT(2, ("Missing mandatory resource, need at least one GP and one PP, both with a separate MMU\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	MALI_DEBUG_ASSERT(1 <= mali_l2_cache_core_get_glob_num_l2_cores());
+	group = mali_create_group(mali_l2_cache_core_get_glob_l2_core(cluster_id_gp), &resource_gp_mmu, &resource_gp, NULL, MALI_DOMAIN_INDEX_GP);
+	if (NULL == group) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Create group for first (and mandatory) PP core */
+	MALI_DEBUG_ASSERT(mali_l2_cache_core_get_glob_num_l2_cores() >= (cluster_id_pp_grp0 + 1)); /* >= 1 on Mali-300 and Mali-400, >= 2 on Mali-450 */
+	group = mali_create_group(mali_l2_cache_core_get_glob_l2_core(cluster_id_pp_grp0), &resource_pp_mmu[0], NULL, &resource_pp[0], MALI_DOMAIN_INDEX_PP0);
+	if (NULL == group) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	mali_inited_pp_cores_group_1++;
+
+	/* Create groups for rest of the cores in the first PP core group */
+	for (i = 1; i < 4; i++) { /* First half of the PP cores belong to first core group */
+		if (mali_inited_pp_cores_group_1 < mali_max_pp_cores_group_1) {
+			if (_MALI_OSK_ERR_OK == resource_pp_found[i] && _MALI_OSK_ERR_OK == resource_pp_mmu_found[i]) {
+				group = mali_create_group(mali_l2_cache_core_get_glob_l2_core(cluster_id_pp_grp0), &resource_pp_mmu[i], NULL, &resource_pp[i], MALI_DOMAIN_INDEX_PP0 + i);
+				if (NULL == group) {
+					return _MALI_OSK_ERR_FAULT;
+				}
+
+				mali_inited_pp_cores_group_1++;
+			}
+		}
+	}
+
+	/* Create groups for cores in the second PP core group */
+	for (i = 4; i < 8; i++) { /* Second half of the PP cores belong to second core group */
+		if (mali_inited_pp_cores_group_2 < mali_max_pp_cores_group_2) {
+			if (_MALI_OSK_ERR_OK == resource_pp_found[i] && _MALI_OSK_ERR_OK == resource_pp_mmu_found[i]) {
+				MALI_DEBUG_ASSERT(mali_l2_cache_core_get_glob_num_l2_cores() >= 2); /* Only Mali-450 have a second core group */
+				group = mali_create_group(mali_l2_cache_core_get_glob_l2_core(cluster_id_pp_grp1), &resource_pp_mmu[i], NULL, &resource_pp[i], MALI_DOMAIN_INDEX_PP0 + i);
+				if (NULL == group) {
+					return _MALI_OSK_ERR_FAULT;
+				}
+
+				mali_inited_pp_cores_group_2++;
+			}
+		}
+	}
+
+	if (mali_is_mali450() || mali_is_mali470()) {
+		_mali_osk_errcode_t err = mali_create_virtual_group(&resource_pp_mmu_bcast, &resource_pp_bcast, &resource_dlbu, &resource_bcast);
+		if (_MALI_OSK_ERR_OK != err) {
+			return err;
+		}
+	}
+
+	mali_max_pp_cores_group_1 = mali_inited_pp_cores_group_1;
+	mali_max_pp_cores_group_2 = mali_inited_pp_cores_group_2;
+	MALI_DEBUG_PRINT(2, ("%d+%d PP cores initialized\n", mali_inited_pp_cores_group_1, mali_inited_pp_cores_group_2));
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static _mali_osk_errcode_t mali_check_shared_interrupts(void)
+{
+#if !defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	if (MALI_TRUE == _mali_osk_shared_interrupts()) {
+		MALI_PRINT_ERROR(("Shared interrupts detected, but driver support is not enabled\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif /* !defined(CONFIG_MALI_SHARED_INTERRUPTS) */
+
+	/* It is OK to compile support for shared interrupts even if Mali is not using it. */
+	return _MALI_OSK_ERR_OK;
+}
+
+static _mali_osk_errcode_t mali_parse_config_pmu(void)
+{
+	_mali_osk_resource_t resource_pmu;
+
+	MALI_DEBUG_ASSERT(0 != global_gpu_base_address);
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI_OFFSET_PMU, &resource_pmu)) {
+		struct mali_pmu_core *pmu;
+
+		pmu = mali_pmu_create(&resource_pmu);
+		if (NULL == pmu) {
+			MALI_PRINT_ERROR(("Failed to create PMU\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+
+	/* It's ok if the PMU doesn't exist */
+	return _MALI_OSK_ERR_OK;
+}
+
+static _mali_osk_errcode_t mali_parse_config_memory(void)
+{
+	_mali_osk_device_data data = { 0, };
+	_mali_osk_errcode_t ret;
+
+	/* The priority of setting the value of mali_shared_mem_size,
+	 * mali_dedicated_mem_start and mali_dedicated_mem_size:
+	 * 1. module parameter;
+	 * 2. platform data;
+	 * 3. default value;
+	 **/
+	if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+		/* Memory settings are not overridden by module parameters, so use device settings */
+		if (0 == mali_dedicated_mem_start && 0 == mali_dedicated_mem_size) {
+			/* Use device specific settings (if defined) */
+			mali_dedicated_mem_start = data.dedicated_mem_start;
+			mali_dedicated_mem_size = data.dedicated_mem_size;
+		}
+
+		if (MALI_SHARED_MEMORY_DEFAULT_SIZE == mali_shared_mem_size &&
+		    0 != data.shared_mem_size) {
+			mali_shared_mem_size = data.shared_mem_size;
+		}
+	}
+
+	if (0 < mali_dedicated_mem_size && 0 != mali_dedicated_mem_start) {
+		MALI_DEBUG_PRINT(2, ("Mali memory settings (dedicated: 0x%08X@0x%08X)\n",
+				     mali_dedicated_mem_size, mali_dedicated_mem_start));
+
+		/* Dedicated memory */
+		ret = mali_memory_core_resource_dedicated_memory(mali_dedicated_mem_start, mali_dedicated_mem_size);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_PRINT_ERROR(("Failed to register dedicated memory\n"));
+			mali_memory_terminate();
+			return ret;
+		}
+	}
+
+	if (0 < mali_shared_mem_size) {
+		MALI_DEBUG_PRINT(2, ("Mali memory settings (shared: 0x%08X)\n", mali_shared_mem_size));
+
+		/* Shared OS memory */
+		ret = mali_memory_core_resource_os_memory(mali_shared_mem_size);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_PRINT_ERROR(("Failed to register shared OS memory\n"));
+			mali_memory_terminate();
+			return ret;
+		}
+	}
+
+	if (0 == mali_fb_start && 0 == mali_fb_size) {
+		/* Frame buffer settings are not overridden by module parameters, so use device settings */
+		_mali_osk_device_data data = { 0, };
+
+		if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+			/* Use device specific settings (if defined) */
+			mali_fb_start = data.fb_start;
+			mali_fb_size = data.fb_size;
+		}
+
+		MALI_DEBUG_PRINT(2, ("Using device defined frame buffer settings (0x%08X@0x%08X)\n",
+				     mali_fb_size, mali_fb_start));
+	} else {
+		MALI_DEBUG_PRINT(2, ("Using module defined frame buffer settings (0x%08X@0x%08X)\n",
+				     mali_fb_size, mali_fb_start));
+	}
+
+	if (0 != mali_fb_size) {
+		/* Register frame buffer */
+		ret = mali_mem_validation_add_range(mali_fb_start, mali_fb_size);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_PRINT_ERROR(("Failed to register frame buffer memory region\n"));
+			mali_memory_terminate();
+			return ret;
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static void mali_detect_gpu_class(void)
+{
+	if (_mali_osk_identify_gpu_resource() == 0x450)
+		mali_gpu_class_is_mali450 = MALI_TRUE;
+
+	if (_mali_osk_identify_gpu_resource() == 0x470)
+		mali_gpu_class_is_mali470 = MALI_TRUE;
+}
+
+static _mali_osk_errcode_t mali_init_hw_reset(void)
+{
+#if (defined(CONFIG_MALI450) || defined(CONFIG_MALI470))
+	_mali_osk_resource_t resource_bcast;
+
+	/* Ensure broadcast unit is in a good state before we start creating
+	 * groups and cores.
+	 */
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI_OFFSET_BCAST, &resource_bcast)) {
+		struct mali_bcast_unit *bcast_core;
+
+		bcast_core = mali_bcast_unit_create(&resource_bcast);
+		if (NULL == bcast_core) {
+			MALI_PRINT_ERROR(("Failed to create Broadcast unit object!\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+		mali_bcast_unit_delete(bcast_core);
+	}
+#endif /* (defined(CONFIG_MALI450) || defined(CONFIG_MALI470)) */
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_initialize_subsystems(void)
+{
+	_mali_osk_errcode_t err;
+
+#ifdef CONFIG_MALI_DT
+	err = _mali_osk_resource_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+#endif
+
+	mali_pp_job_initialize();
+
+	err = mali_timeline_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	err = mali_session_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/*Try to init gpu secure mode */
+	_mali_osk_gpu_secure_mode_init();
+
+#if defined(CONFIG_MALI400_PROFILING)
+	err = _mali_osk_profiling_init(mali_boot_profiling ? MALI_TRUE : MALI_FALSE);
+	if (_MALI_OSK_ERR_OK != err) {
+		/* No biggie if we weren't able to initialize the profiling */
+		MALI_PRINT_ERROR(("Failed to initialize profiling, feature will be unavailable\n"));
+	}
+#endif
+
+	err = mali_memory_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	err = mali_executor_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	err = mali_scheduler_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Configure memory early, needed by mali_mmu_initialize. */
+	err = mali_parse_config_memory();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	err = mali_set_global_gpu_base_address();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Detect GPU class (uses L2 cache count) */
+	mali_detect_gpu_class();
+
+	err = mali_check_shared_interrupts();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Initialize the MALI PMU (will not touch HW!) */
+	err = mali_parse_config_pmu();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Initialize the power management module */
+	err = mali_pm_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Make sure the entire GPU stays on for the rest of this function */
+	mali_pm_init_begin();
+
+	/* Ensure HW is in a good state before starting to access cores. */
+	err = mali_init_hw_reset();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Detect which Mali GPU we are dealing with */
+	err = mali_parse_product_info();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* The global_product_id is now populated with the correct Mali GPU */
+
+	/* Start configuring the actual Mali hardware. */
+
+	err = mali_mmu_initialize();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	if (mali_is_mali450() || mali_is_mali470()) {
+		err = mali_dlbu_initialize();
+		if (_MALI_OSK_ERR_OK != err) {
+			mali_pm_init_end();
+			mali_terminate_subsystems();
+			return err;
+		}
+	}
+
+	err = mali_parse_config_l2_cache();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	err = mali_parse_config_groups();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Move groups into executor */
+	mali_executor_populate();
+
+	/* Need call after all group has assigned a domain */
+	mali_pm_power_cost_setup();
+
+	/* Initialize the GPU timer */
+	err = mali_control_timer_init();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+
+	/* Initialize the GPU utilization tracking */
+	err = mali_utilization_init();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+
+#if defined(CONFIG_MALI_DVFS)
+	err = mali_dvfs_policy_init();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_init_end();
+		mali_terminate_subsystems();
+		return err;
+	}
+#endif
+
+	/* Allowing the system to be turned off */
+	mali_pm_init_end();
+
+	return _MALI_OSK_ERR_OK; /* all ok */
+}
+
+void mali_terminate_subsystems(void)
+{
+	struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+
+	MALI_DEBUG_PRINT(2, ("terminate_subsystems() called\n"));
+
+	mali_utilization_term();
+	mali_control_timer_term();
+
+	mali_executor_depopulate();
+	mali_delete_groups(); /* Delete groups not added to executor */
+	mali_executor_terminate();
+
+	mali_scheduler_terminate();
+	mali_pp_job_terminate();
+	mali_delete_l2_cache_cores();
+	mali_mmu_terminate();
+
+	if (mali_is_mali450() || mali_is_mali470()) {
+		mali_dlbu_terminate();
+	}
+
+	mali_pm_terminate();
+
+	if (NULL != pmu) {
+		mali_pmu_delete(pmu);
+	}
+
+#if defined(CONFIG_MALI400_PROFILING)
+	_mali_osk_profiling_term();
+#endif
+
+	_mali_osk_gpu_secure_mode_deinit();
+
+	mali_memory_terminate();
+
+	mali_session_terminate();
+
+	mali_timeline_terminate();
+
+	global_gpu_base_address = 0;
+}
+
+_mali_product_id_t mali_kernel_core_get_product_id(void)
+{
+	return global_product_id;
+}
+
+u32 mali_kernel_core_get_gpu_major_version(void)
+{
+	return global_gpu_major_version;
+}
+
+u32 mali_kernel_core_get_gpu_minor_version(void)
+{
+	return global_gpu_minor_version;
+}
+
+_mali_osk_errcode_t _mali_ukk_get_api_version(_mali_uk_get_api_version_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	/* check compatability */
+	if (args->version == _MALI_UK_API_VERSION) {
+		args->compatible = 1;
+	} else {
+		args->compatible = 0;
+	}
+
+	args->version = _MALI_UK_API_VERSION; /* report our version */
+
+	/* success regardless of being compatible or not */
+	MALI_SUCCESS;
+}
+
+_mali_osk_errcode_t _mali_ukk_get_api_version_v2(_mali_uk_get_api_version_v2_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	/* check compatability */
+	if (args->version == _MALI_UK_API_VERSION) {
+		args->compatible = 1;
+	} else {
+		args->compatible = 0;
+	}
+
+	args->version = _MALI_UK_API_VERSION; /* report our version */
+
+	/* success regardless of being compatible or not */
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_wait_for_notification(_mali_uk_wait_for_notification_s *args)
+{
+	_mali_osk_errcode_t err;
+	_mali_osk_notification_t *notification;
+	_mali_osk_notification_queue_t *queue;
+	struct mali_session_data *session;
+
+	/* check input */
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	queue = session->ioctl_queue;
+
+	/* if the queue does not exist we're currently shutting down */
+	if (NULL == queue) {
+		MALI_DEBUG_PRINT(1, ("No notification queue registered with the session. Asking userspace to stop querying\n"));
+		args->type = _MALI_NOTIFICATION_CORE_SHUTDOWN_IN_PROGRESS;
+		return _MALI_OSK_ERR_OK;
+	}
+
+	/* receive a notification, might sleep */
+	err = _mali_osk_notification_queue_receive(queue, &notification);
+	if (_MALI_OSK_ERR_OK != err) {
+		MALI_ERROR(err); /* errcode returned, pass on to caller */
+	}
+
+	/* copy the buffer to the user */
+	args->type = (_mali_uk_notification_type)notification->notification_type;
+	_mali_osk_memcpy(&args->data, notification->result_buffer, notification->result_buffer_size);
+
+	/* finished with the notification */
+	_mali_osk_notification_delete(notification);
+
+	return _MALI_OSK_ERR_OK; /* all ok */
+}
+
+_mali_osk_errcode_t _mali_ukk_post_notification(_mali_uk_post_notification_s *args)
+{
+	_mali_osk_notification_t *notification;
+	_mali_osk_notification_queue_t *queue;
+	struct mali_session_data *session;
+
+	/* check input */
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	queue = session->ioctl_queue;
+
+	/* if the queue does not exist we're currently shutting down */
+	if (NULL == queue) {
+		MALI_DEBUG_PRINT(1, ("No notification queue registered with the session. Asking userspace to stop querying\n"));
+		return _MALI_OSK_ERR_OK;
+	}
+
+	notification = _mali_osk_notification_create(args->type, 0);
+	if (NULL == notification) {
+		MALI_PRINT_ERROR(("Failed to create notification object\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	_mali_osk_notification_queue_send(queue, notification);
+
+	return _MALI_OSK_ERR_OK; /* all ok */
+}
+
+_mali_osk_errcode_t _mali_ukk_pending_submit(_mali_uk_pending_submit_s *args)
+{
+	wait_queue_head_t *queue;
+
+	/* check input */
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	queue = mali_session_get_wait_queue();
+
+	/* check pending big job number, might sleep if larger than MAX allowed number */
+	if (wait_event_interruptible(*queue, MALI_MAX_PENDING_BIG_JOB > mali_scheduler_job_gp_big_job_count())) {
+		return _MALI_OSK_ERR_RESTARTSYSCALL;
+	}
+
+	return _MALI_OSK_ERR_OK; /* all ok */
+}
+
+
+_mali_osk_errcode_t _mali_ukk_request_high_priority(_mali_uk_request_high_priority_s *args)
+{
+	struct mali_session_data *session;
+
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)args->ctx;
+
+	if (!session->use_high_priority_job_queue) {
+		session->use_high_priority_job_queue = MALI_TRUE;
+		MALI_DEBUG_PRINT(2, ("Session 0x%08X with pid %d was granted higher priority.\n", session, _mali_osk_get_pid()));
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_open(void **context)
+{
+	u32 i;
+	struct mali_session_data *session;
+
+	/* allocated struct to track this session */
+	session = (struct mali_session_data *)_mali_osk_calloc(1, sizeof(struct mali_session_data));
+	MALI_CHECK_NON_NULL(session, _MALI_OSK_ERR_NOMEM);
+
+	MALI_DEBUG_PRINT(3, ("Session starting\n"));
+
+	/* create a response queue for this session */
+	session->ioctl_queue = _mali_osk_notification_queue_init();
+	if (NULL == session->ioctl_queue) {
+		goto err;
+	}
+
+	/*create a wait queue for this session */
+	session->wait_queue = _mali_osk_wait_queue_init();
+	if (NULL == session->wait_queue) {
+		goto err_wait_queue;
+	}
+
+	session->page_directory = mali_mmu_pagedir_alloc();
+	if (NULL == session->page_directory) {
+		goto err_mmu;
+	}
+
+	if (_MALI_OSK_ERR_OK != mali_mmu_pagedir_map(session->page_directory, MALI_DLBU_VIRT_ADDR, _MALI_OSK_MALI_PAGE_SIZE)) {
+		MALI_PRINT_ERROR(("Failed to map DLBU page into session\n"));
+		goto err_mmu;
+	}
+
+	if (0 != mali_dlbu_phys_addr) {
+		mali_mmu_pagedir_update(session->page_directory, MALI_DLBU_VIRT_ADDR, mali_dlbu_phys_addr,
+					_MALI_OSK_MALI_PAGE_SIZE, MALI_MMU_FLAGS_DEFAULT);
+	}
+
+	if (_MALI_OSK_ERR_OK != mali_memory_session_begin(session)) {
+		goto err_session;
+	}
+
+	/* Create soft system. */
+	session->soft_job_system = mali_soft_job_system_create(session);
+	if (NULL == session->soft_job_system) {
+		goto err_soft;
+	}
+
+	/* Initialize the dma fence context.*/
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	session->fence_context = dma_fence_context_alloc(1);
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(3, 17, 0)
+	session->fence_context = fence_context_alloc(1);
+	_mali_osk_atomic_init(&session->fence_seqno, 0);
+#else
+	MALI_PRINT_ERROR(("The kernel version not support dma fence!\n"));
+	goto err_time_line;
+#endif
+#endif
+
+	/* Create timeline system. */
+	session->timeline_system = mali_timeline_system_create(session);
+	if (NULL == session->timeline_system) {
+		goto err_time_line;
+	}
+
+#if defined(CONFIG_MALI_DVFS)
+	_mali_osk_atomic_init(&session->number_of_window_jobs, 0);
+#endif
+
+	_mali_osk_atomic_init(&session->number_of_pp_jobs, 0);
+
+	session->use_high_priority_job_queue = MALI_FALSE;
+
+	/* Initialize list of PP jobs on this session. */
+	_MALI_OSK_INIT_LIST_HEAD(&session->pp_job_list);
+
+	/* Initialize the pp_job_fb_lookup_list array used to quickly lookup jobs from a given frame builder */
+	for (i = 0; i < MALI_PP_JOB_FB_LOOKUP_LIST_SIZE; ++i) {
+		_MALI_OSK_INIT_LIST_HEAD(&session->pp_job_fb_lookup_list[i]);
+	}
+
+	session->pid = _mali_osk_get_pid();
+	session->comm = _mali_osk_get_comm();
+	session->max_mali_mem_allocated_size = 0;
+	for (i = 0; i < MALI_MEM_TYPE_MAX; i ++) {
+		atomic_set(&session->mali_mem_array[i], 0);
+	}
+	atomic_set(&session->mali_mem_allocated_pages, 0);
+	*context = (void *)session;
+
+	/* Add session to the list of all sessions. */
+	mali_session_add(session);
+
+	MALI_DEBUG_PRINT(3, ("Session started\n"));
+	return _MALI_OSK_ERR_OK;
+
+err_time_line:
+	mali_soft_job_system_destroy(session->soft_job_system);
+err_soft:
+	mali_memory_session_end(session);
+err_session:
+	mali_mmu_pagedir_free(session->page_directory);
+err_mmu:
+	_mali_osk_wait_queue_term(session->wait_queue);
+err_wait_queue:
+	_mali_osk_notification_queue_term(session->ioctl_queue);
+err:
+	_mali_osk_free(session);
+	MALI_ERROR(_MALI_OSK_ERR_NOMEM);
+
+}
+
+#if defined(DEBUG)
+/* parameter used for debug */
+extern u32 num_pm_runtime_resume;
+extern u32 num_pm_updates;
+extern u32 num_pm_updates_up;
+extern u32 num_pm_updates_down;
+#endif
+
+_mali_osk_errcode_t _mali_ukk_close(void **context)
+{
+	struct mali_session_data *session;
+	MALI_CHECK_NON_NULL(context, _MALI_OSK_ERR_INVALID_ARGS);
+	session = (struct mali_session_data *)*context;
+
+	MALI_DEBUG_PRINT(3, ("Session ending\n"));
+
+	MALI_DEBUG_ASSERT_POINTER(session->soft_job_system);
+	MALI_DEBUG_ASSERT_POINTER(session->timeline_system);
+
+	/* Remove session from list of all sessions. */
+	mali_session_remove(session);
+
+	/* This flag is used to prevent queueing of jobs due to activation. */
+	session->is_aborting = MALI_TRUE;
+
+	/* Stop the soft job timer. */
+	mali_timeline_system_stop_timer(session->timeline_system);
+
+	/* Abort queued jobs */
+	mali_scheduler_abort_session(session);
+
+	/* Abort executing jobs */
+	mali_executor_abort_session(session);
+
+	/* Abort the soft job system. */
+	mali_soft_job_system_abort(session->soft_job_system);
+
+	/* Force execution of all pending bottom half processing for GP and PP. */
+	_mali_osk_wq_flush();
+
+	/* The session PP list should now be empty. */
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(&session->pp_job_list));
+
+	/* At this point the GP and PP scheduler no longer has any jobs queued or running from this
+	 * session, and all soft jobs in the soft job system has been destroyed. */
+
+	/* Any trackers left in the timeline system are directly or indirectly waiting on external
+	 * sync fences.  Cancel all sync fence waiters to trigger activation of all remaining
+	 * trackers.  This call will sleep until all timelines are empty. */
+	mali_timeline_system_abort(session->timeline_system);
+
+	/* Flush pending work.
+	 * Needed to make sure all bottom half processing related to this
+	 * session has been completed, before we free internal data structures.
+	 */
+	_mali_osk_wq_flush();
+
+	/* Destroy timeline system. */
+	mali_timeline_system_destroy(session->timeline_system);
+	session->timeline_system = NULL;
+
+	/* Destroy soft system. */
+	mali_soft_job_system_destroy(session->soft_job_system);
+	session->soft_job_system = NULL;
+
+	/*Wait for the session job lists become empty.*/
+	_mali_osk_wait_queue_wait_event(session->wait_queue, mali_session_pp_job_is_empty, (void *) session);
+
+	/* Free remaining memory allocated to this session */
+	mali_memory_session_end(session);
+
+#if defined(CONFIG_MALI_DVFS)
+	_mali_osk_atomic_term(&session->number_of_window_jobs);
+#endif
+
+#if defined(CONFIG_MALI400_PROFILING)
+	_mali_osk_profiling_stop_sampling(session->pid);
+#endif
+
+	/* Free session data structures */
+	mali_mmu_pagedir_unmap(session->page_directory, MALI_DLBU_VIRT_ADDR, _MALI_OSK_MALI_PAGE_SIZE);
+	mali_mmu_pagedir_free(session->page_directory);
+	_mali_osk_wait_queue_term(session->wait_queue);
+	_mali_osk_notification_queue_term(session->ioctl_queue);
+	_mali_osk_free(session);
+
+	*context = NULL;
+
+	MALI_DEBUG_PRINT(3, ("Session has ended\n"));
+
+#if defined(DEBUG)
+	MALI_DEBUG_PRINT(3, ("Stats: # runtime resumes: %u\n", num_pm_runtime_resume));
+	MALI_DEBUG_PRINT(3, ("       # PM updates: .... %u (up %u, down %u)\n", num_pm_updates, num_pm_updates_up, num_pm_updates_down));
+
+	num_pm_runtime_resume = 0;
+	num_pm_updates = 0;
+	num_pm_updates_up = 0;
+	num_pm_updates_down = 0;
+#endif
+
+	return _MALI_OSK_ERR_OK;;
+}
+
+#if MALI_STATE_TRACKING
+u32 _mali_kernel_core_dump_state(char *buf, u32 size)
+{
+	int n = 0; /* Number of bytes written to buf */
+
+	n += mali_scheduler_dump_state(buf + n, size - n);
+	n += mali_executor_dump_state(buf + n, size - n);
+
+	return n;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_kernel_core.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_kernel_core.h
@@ -0,0 +1,57 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_KERNEL_CORE_H__
+#define __MALI_KERNEL_CORE_H__
+
+#include "mali_osk.h"
+
+typedef enum {
+	_MALI_PRODUCT_ID_UNKNOWN,
+	_MALI_PRODUCT_ID_MALI200,
+	_MALI_PRODUCT_ID_MALI300,
+	_MALI_PRODUCT_ID_MALI400,
+	_MALI_PRODUCT_ID_MALI450,
+	_MALI_PRODUCT_ID_MALI470,
+} _mali_product_id_t;
+
+extern mali_bool mali_gpu_class_is_mali450;
+extern mali_bool mali_gpu_class_is_mali470;
+
+_mali_osk_errcode_t mali_initialize_subsystems(void);
+
+void mali_terminate_subsystems(void);
+
+_mali_product_id_t mali_kernel_core_get_product_id(void);
+
+u32 mali_kernel_core_get_gpu_major_version(void);
+
+u32 mali_kernel_core_get_gpu_minor_version(void);
+
+u32 _mali_kernel_core_dump_state(char *buf, u32 size);
+
+MALI_STATIC_INLINE mali_bool mali_is_mali470(void)
+{
+	return mali_gpu_class_is_mali470;
+}
+
+MALI_STATIC_INLINE mali_bool mali_is_mali450(void)
+{
+	return mali_gpu_class_is_mali450;
+}
+
+MALI_STATIC_INLINE mali_bool mali_is_mali400(void)
+{
+	if (mali_gpu_class_is_mali450 || mali_gpu_class_is_mali470)
+		return MALI_FALSE;
+
+	return MALI_TRUE;
+}
+#endif /* __MALI_KERNEL_CORE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_kernel_utilization.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_kernel_utilization.c
@@ -0,0 +1,440 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_utilization.h"
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_scheduler.h"
+
+#include "mali_executor.h"
+#include "mali_dvfs_policy.h"
+#include "mali_control_timer.h"
+
+/* Thresholds for GP bound detection. */
+#define MALI_GP_BOUND_GP_UTILIZATION_THRESHOLD 240
+#define MALI_GP_BOUND_PP_UTILIZATION_THRESHOLD 250
+
+static _mali_osk_spinlock_irq_t *utilization_data_lock;
+
+static u32 num_running_gp_cores = 0;
+static u32 num_running_pp_cores = 0;
+
+static u64 work_start_time_gpu = 0;
+static u64 work_start_time_gp = 0;
+static u64 work_start_time_pp = 0;
+static u64 accumulated_work_time_gpu = 0;
+static u64 accumulated_work_time_gp = 0;
+static u64 accumulated_work_time_pp = 0;
+
+static u32 last_utilization_gpu = 0 ;
+static u32 last_utilization_gp = 0 ;
+static u32 last_utilization_pp = 0 ;
+
+void (*mali_utilization_callback)(struct mali_gpu_utilization_data *data) = NULL;
+
+/* Define the first timer control timer timeout in milliseconds */
+static u32 mali_control_first_timeout = 100;
+static struct mali_gpu_utilization_data mali_util_data = {0, };
+
+struct mali_gpu_utilization_data *mali_utilization_calculate(u64 *start_time, u64 *time_period, mali_bool *need_add_timer)
+{
+	u64 time_now;
+	u32 leading_zeroes;
+	u32 shift_val;
+	u32 work_normalized_gpu;
+	u32 work_normalized_gp;
+	u32 work_normalized_pp;
+	u32 period_normalized;
+	u32 utilization_gpu;
+	u32 utilization_gp;
+	u32 utilization_pp;
+
+	mali_utilization_data_lock();
+
+	time_now = _mali_osk_time_get_ns();
+
+	*time_period = time_now - *start_time;
+
+	if (accumulated_work_time_gpu == 0 && work_start_time_gpu == 0) {
+		mali_control_timer_pause();
+		/*
+		 * No work done for this period
+		 * - No need to reschedule timer
+		 * - Report zero usage
+		 */
+		last_utilization_gpu = 0;
+		last_utilization_gp = 0;
+		last_utilization_pp = 0;
+
+		mali_util_data.utilization_gpu = last_utilization_gpu;
+		mali_util_data.utilization_gp = last_utilization_gp;
+		mali_util_data.utilization_pp = last_utilization_pp;
+
+		mali_utilization_data_unlock();
+
+		*need_add_timer = MALI_FALSE;
+
+		mali_executor_hint_disable(MALI_EXECUTOR_HINT_GP_BOUND);
+
+		MALI_DEBUG_PRINT(4, ("last_utilization_gpu = %d \n", last_utilization_gpu));
+		MALI_DEBUG_PRINT(4, ("last_utilization_gp = %d \n", last_utilization_gp));
+		MALI_DEBUG_PRINT(4, ("last_utilization_pp = %d \n", last_utilization_pp));
+
+		return &mali_util_data;
+	}
+
+	/* If we are currently busy, update working period up to now */
+	if (work_start_time_gpu != 0) {
+		accumulated_work_time_gpu += (time_now - work_start_time_gpu);
+		work_start_time_gpu = time_now;
+
+		/* GP and/or PP will also be busy if the GPU is busy at this point */
+
+		if (work_start_time_gp != 0) {
+			accumulated_work_time_gp += (time_now - work_start_time_gp);
+			work_start_time_gp = time_now;
+		}
+
+		if (work_start_time_pp != 0) {
+			accumulated_work_time_pp += (time_now - work_start_time_pp);
+			work_start_time_pp = time_now;
+		}
+	}
+
+	/*
+	 * We have two 64-bit values, a dividend and a divisor.
+	 * To avoid dependencies to a 64-bit divider, we shift down the two values
+	 * equally first.
+	 * We shift the dividend up and possibly the divisor down, making the result X in 256.
+	 */
+
+	/* Shift the 64-bit values down so they fit inside a 32-bit integer */
+	leading_zeroes = _mali_osk_clz((u32)(*time_period >> 32));
+	shift_val = 32 - leading_zeroes;
+	work_normalized_gpu = (u32)(accumulated_work_time_gpu >> shift_val);
+	work_normalized_gp = (u32)(accumulated_work_time_gp >> shift_val);
+	work_normalized_pp = (u32)(accumulated_work_time_pp >> shift_val);
+	period_normalized = (u32)(*time_period >> shift_val);
+
+	/*
+	 * Now, we should report the usage in parts of 256
+	 * this means we must shift up the dividend or down the divisor by 8
+	 * (we could do a combination, but we just use one for simplicity,
+	 * but the end result should be good enough anyway)
+	 */
+	if (period_normalized > 0x00FFFFFF) {
+		/* The divisor is so big that it is safe to shift it down */
+		period_normalized >>= 8;
+	} else {
+		/*
+		 * The divisor is so small that we can shift up the dividend, without loosing any data.
+		 * (dividend is always smaller than the divisor)
+		 */
+		work_normalized_gpu <<= 8;
+		work_normalized_gp <<= 8;
+		work_normalized_pp <<= 8;
+	}
+
+	utilization_gpu = work_normalized_gpu / period_normalized;
+	utilization_gp = work_normalized_gp / period_normalized;
+	utilization_pp = work_normalized_pp / period_normalized;
+
+	last_utilization_gpu = utilization_gpu;
+	last_utilization_gp = utilization_gp;
+	last_utilization_pp = utilization_pp;
+
+	if ((MALI_GP_BOUND_GP_UTILIZATION_THRESHOLD < last_utilization_gp) &&
+	    (MALI_GP_BOUND_PP_UTILIZATION_THRESHOLD > last_utilization_pp)) {
+		mali_executor_hint_enable(MALI_EXECUTOR_HINT_GP_BOUND);
+	} else {
+		mali_executor_hint_disable(MALI_EXECUTOR_HINT_GP_BOUND);
+	}
+
+	/* starting a new period */
+	accumulated_work_time_gpu = 0;
+	accumulated_work_time_gp = 0;
+	accumulated_work_time_pp = 0;
+
+	*start_time = time_now;
+
+	mali_util_data.utilization_gp = last_utilization_gp;
+	mali_util_data.utilization_gpu = last_utilization_gpu;
+	mali_util_data.utilization_pp = last_utilization_pp;
+
+	mali_utilization_data_unlock();
+
+	*need_add_timer = MALI_TRUE;
+
+	MALI_DEBUG_PRINT(4, ("last_utilization_gpu = %d \n", last_utilization_gpu));
+	MALI_DEBUG_PRINT(4, ("last_utilization_gp = %d \n", last_utilization_gp));
+	MALI_DEBUG_PRINT(4, ("last_utilization_pp = %d \n", last_utilization_pp));
+
+	return &mali_util_data;
+}
+
+_mali_osk_errcode_t mali_utilization_init(void)
+{
+#if USING_GPU_UTILIZATION
+	_mali_osk_device_data data;
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+		if (NULL != data.utilization_callback) {
+			mali_utilization_callback = data.utilization_callback;
+			MALI_DEBUG_PRINT(2, ("Mali GPU Utilization: Utilization handler installed \n"));
+		}
+	}
+#endif /* defined(USING_GPU_UTILIZATION) */
+
+	if (NULL == mali_utilization_callback) {
+		MALI_DEBUG_PRINT(2, ("Mali GPU Utilization: No platform utilization handler installed\n"));
+	}
+
+	utilization_data_lock = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_ORDERED, _MALI_OSK_LOCK_ORDER_UTILIZATION);
+	if (NULL == utilization_data_lock) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	num_running_gp_cores = 0;
+	num_running_pp_cores = 0;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_utilization_term(void)
+{
+	if (NULL != utilization_data_lock) {
+		_mali_osk_spinlock_irq_term(utilization_data_lock);
+	}
+}
+
+void mali_utilization_gp_start(void)
+{
+	mali_utilization_data_lock();
+
+	++num_running_gp_cores;
+	if (1 == num_running_gp_cores) {
+		u64 time_now = _mali_osk_time_get_ns();
+
+		/* First GP core started, consider GP busy from now and onwards */
+		work_start_time_gp = time_now;
+
+		if (0 == num_running_pp_cores) {
+			mali_bool is_resume = MALI_FALSE;
+			/*
+			 * There are no PP cores running, so this is also the point
+			 * at which we consider the GPU to be busy as well.
+			 */
+			work_start_time_gpu = time_now;
+
+			is_resume  = mali_control_timer_resume(time_now);
+
+			mali_utilization_data_unlock();
+
+			if (is_resume) {
+				/* Do some policy in new period for performance consideration */
+#if defined(CONFIG_MALI_DVFS)
+				/* Clear session->number_of_window_jobs, prepare parameter for dvfs */
+				mali_session_max_window_num();
+				if (0 == last_utilization_gpu) {
+					/*
+					 * for mali_dev_pause is called in set clock,
+					 * so each time we change clock, we will set clock to
+					 * highest step even if under down clock case,
+					 * it is not nessesary, so we only set the clock under
+					 * last time utilization equal 0, we stop the timer then
+					 * start the GPU again case
+					 */
+					mali_dvfs_policy_new_period();
+				}
+#endif
+				/*
+				 * First timeout using short interval for power consideration
+				 * because we give full power in the new period, but if the
+				 * job loading is light, finish in 10ms, the other time all keep
+				 * in high freq it will wast time.
+				 */
+				mali_control_timer_add(mali_control_first_timeout);
+			}
+		} else {
+			mali_utilization_data_unlock();
+		}
+
+	} else {
+		/* Nothing to do */
+		mali_utilization_data_unlock();
+	}
+}
+
+void mali_utilization_pp_start(void)
+{
+	mali_utilization_data_lock();
+
+	++num_running_pp_cores;
+	if (1 == num_running_pp_cores) {
+		u64 time_now = _mali_osk_time_get_ns();
+
+		/* First PP core started, consider PP busy from now and onwards */
+		work_start_time_pp = time_now;
+
+		if (0 == num_running_gp_cores) {
+			mali_bool is_resume = MALI_FALSE;
+			/*
+			 * There are no GP cores running, so this is also the point
+			 * at which we consider the GPU to be busy as well.
+			 */
+			work_start_time_gpu = time_now;
+
+			/* Start a new period if stoped */
+			is_resume = mali_control_timer_resume(time_now);
+
+			mali_utilization_data_unlock();
+
+			if (is_resume) {
+#if defined(CONFIG_MALI_DVFS)
+				/* Clear session->number_of_window_jobs, prepare parameter for dvfs */
+				mali_session_max_window_num();
+				if (0 == last_utilization_gpu) {
+					/*
+					 * for mali_dev_pause is called in set clock,
+					 * so each time we change clock, we will set clock to
+					 * highest step even if under down clock case,
+					 * it is not nessesary, so we only set the clock under
+					 * last time utilization equal 0, we stop the timer then
+					 * start the GPU again case
+					 */
+					mali_dvfs_policy_new_period();
+				}
+#endif
+
+				/*
+				 * First timeout using short interval for power consideration
+				 * because we give full power in the new period, but if the
+				 * job loading is light, finish in 10ms, the other time all keep
+				 * in high freq it will wast time.
+				 */
+				mali_control_timer_add(mali_control_first_timeout);
+			}
+		} else {
+			mali_utilization_data_unlock();
+		}
+	} else {
+		/* Nothing to do */
+		mali_utilization_data_unlock();
+	}
+}
+
+void mali_utilization_gp_end(void)
+{
+	mali_utilization_data_lock();
+
+	--num_running_gp_cores;
+	if (0 == num_running_gp_cores) {
+		u64 time_now = _mali_osk_time_get_ns();
+
+		/* Last GP core ended, consider GP idle from now and onwards */
+		accumulated_work_time_gp += (time_now - work_start_time_gp);
+		work_start_time_gp = 0;
+
+		if (0 == num_running_pp_cores) {
+			/*
+			 * There are no PP cores running, so this is also the point
+			 * at which we consider the GPU to be idle as well.
+			 */
+			accumulated_work_time_gpu += (time_now - work_start_time_gpu);
+			work_start_time_gpu = 0;
+		}
+	}
+
+	mali_utilization_data_unlock();
+}
+
+void mali_utilization_pp_end(void)
+{
+	mali_utilization_data_lock();
+
+	--num_running_pp_cores;
+	if (0 == num_running_pp_cores) {
+		u64 time_now = _mali_osk_time_get_ns();
+
+		/* Last PP core ended, consider PP idle from now and onwards */
+		accumulated_work_time_pp += (time_now - work_start_time_pp);
+		work_start_time_pp = 0;
+
+		if (0 == num_running_gp_cores) {
+			/*
+			 * There are no GP cores running, so this is also the point
+			 * at which we consider the GPU to be idle as well.
+			 */
+			accumulated_work_time_gpu += (time_now - work_start_time_gpu);
+			work_start_time_gpu = 0;
+		}
+	}
+
+	mali_utilization_data_unlock();
+}
+
+mali_bool mali_utilization_enabled(void)
+{
+#if defined(CONFIG_MALI_DVFS)
+	return mali_dvfs_policy_enabled();
+#else
+	return (NULL != mali_utilization_callback);
+#endif /* defined(CONFIG_MALI_DVFS) */
+}
+
+void mali_utilization_platform_realize(struct mali_gpu_utilization_data *util_data)
+{
+	MALI_DEBUG_ASSERT_POINTER(mali_utilization_callback);
+
+	mali_utilization_callback(util_data);
+}
+
+void mali_utilization_reset(void)
+{
+	accumulated_work_time_gpu = 0;
+	accumulated_work_time_gp = 0;
+	accumulated_work_time_pp = 0;
+
+	last_utilization_gpu = 0;
+	last_utilization_gp = 0;
+	last_utilization_pp = 0;
+}
+
+void mali_utilization_data_lock(void)
+{
+	_mali_osk_spinlock_irq_lock(utilization_data_lock);
+}
+
+void mali_utilization_data_unlock(void)
+{
+	_mali_osk_spinlock_irq_unlock(utilization_data_lock);
+}
+
+void mali_utilization_data_assert_locked(void)
+{
+	MALI_DEBUG_ASSERT_LOCK_HELD(utilization_data_lock);
+}
+
+u32 _mali_ukk_utilization_gp_pp(void)
+{
+	return last_utilization_gpu;
+}
+
+u32 _mali_ukk_utilization_gp(void)
+{
+	return last_utilization_gp;
+}
+
+u32 _mali_ukk_utilization_pp(void)
+{
+	return last_utilization_pp;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_kernel_utilization.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_kernel_utilization.h
@@ -0,0 +1,72 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_KERNEL_UTILIZATION_H__
+#define __MALI_KERNEL_UTILIZATION_H__
+
+#include <linux/mali/mali_utgard.h>
+#include "mali_osk.h"
+
+/**
+ * Initialize/start the Mali GPU utilization metrics reporting.
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t mali_utilization_init(void);
+
+/**
+ * Terminate the Mali GPU utilization metrics reporting
+ */
+void mali_utilization_term(void);
+
+/**
+ * Check if Mali utilization is enabled
+ */
+mali_bool mali_utilization_enabled(void);
+
+/**
+ * Should be called when a job is about to execute a GP job
+ */
+void mali_utilization_gp_start(void);
+
+/**
+ * Should be called when a job has completed executing a GP job
+ */
+void mali_utilization_gp_end(void);
+
+/**
+ * Should be called when a job is about to execute a PP job
+ */
+void mali_utilization_pp_start(void);
+
+/**
+ * Should be called when a job has completed executing a PP job
+ */
+void mali_utilization_pp_end(void);
+
+/**
+ * Should be called to calcution the GPU utilization
+ */
+struct mali_gpu_utilization_data *mali_utilization_calculate(u64 *start_time, u64 *time_period, mali_bool *need_add_timer);
+
+_mali_osk_spinlock_irq_t *mali_utilization_get_lock(void);
+
+void mali_utilization_platform_realize(struct mali_gpu_utilization_data *util_data);
+
+void mali_utilization_data_lock(void);
+
+void mali_utilization_data_unlock(void);
+
+void mali_utilization_data_assert_locked(void);
+
+void mali_utilization_reset(void);
+
+
+#endif /* __MALI_KERNEL_UTILIZATION_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_kernel_vsync.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_kernel_vsync.c
@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2011-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_ukk.h"
+
+#include "mali_osk_profiling.h"
+
+_mali_osk_errcode_t _mali_ukk_vsync_event_report(_mali_uk_vsync_event_report_s *args)
+{
+	_mali_uk_vsync_event event = (_mali_uk_vsync_event)args->event;
+	MALI_IGNORE(event); /* event is not used for release code, and that is OK */
+
+	/*
+	 * Manually generate user space events in kernel space.
+	 * This saves user space from calling kernel space twice in this case.
+	 * We just need to remember to add pid and tid manually.
+	 */
+	if (event == _MALI_UK_VSYNC_EVENT_BEGIN_WAIT) {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SUSPEND |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_VSYNC,
+					      _mali_osk_get_pid(), _mali_osk_get_tid(), 0, 0, 0);
+	}
+
+	if (event == _MALI_UK_VSYNC_EVENT_END_WAIT) {
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_RESUME |
+					      MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+					      MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_VSYNC,
+					      _mali_osk_get_pid(), _mali_osk_get_tid(), 0, 0, 0);
+	}
+
+
+	MALI_DEBUG_PRINT(4, ("Received VSYNC event: %d\n", event));
+	MALI_SUCCESS;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_l2_cache.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_l2_cache.c
@@ -0,0 +1,534 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_l2_cache.h"
+#include "mali_hw_core.h"
+#include "mali_scheduler.h"
+#include "mali_pm.h"
+#include "mali_pm_domain.h"
+
+/**
+ * Size of the Mali L2 cache registers in bytes
+ */
+#define MALI400_L2_CACHE_REGISTERS_SIZE 0x30
+
+/**
+ * Mali L2 cache register numbers
+ * Used in the register read/write routines.
+ * See the hardware documentation for more information about each register
+ */
+typedef enum mali_l2_cache_register {
+	MALI400_L2_CACHE_REGISTER_SIZE         = 0x0004,
+	MALI400_L2_CACHE_REGISTER_STATUS       = 0x0008,
+	/*unused                               = 0x000C */
+	MALI400_L2_CACHE_REGISTER_COMMAND      = 0x0010,
+	MALI400_L2_CACHE_REGISTER_CLEAR_PAGE   = 0x0014,
+	MALI400_L2_CACHE_REGISTER_MAX_READS    = 0x0018,
+	MALI400_L2_CACHE_REGISTER_ENABLE       = 0x001C,
+	MALI400_L2_CACHE_REGISTER_PERFCNT_SRC0 = 0x0020,
+	MALI400_L2_CACHE_REGISTER_PERFCNT_VAL0 = 0x0024,
+	MALI400_L2_CACHE_REGISTER_PERFCNT_SRC1 = 0x0028,
+	MALI400_L2_CACHE_REGISTER_PERFCNT_VAL1 = 0x002C,
+} mali_l2_cache_register;
+
+/**
+ * Mali L2 cache commands
+ * These are the commands that can be sent to the Mali L2 cache unit
+ */
+typedef enum mali_l2_cache_command {
+	MALI400_L2_CACHE_COMMAND_CLEAR_ALL = 0x01,
+} mali_l2_cache_command;
+
+/**
+ * Mali L2 cache commands
+ * These are the commands that can be sent to the Mali L2 cache unit
+ */
+typedef enum mali_l2_cache_enable {
+	MALI400_L2_CACHE_ENABLE_DEFAULT = 0x0, /* Default */
+	MALI400_L2_CACHE_ENABLE_ACCESS = 0x01,
+	MALI400_L2_CACHE_ENABLE_READ_ALLOCATE = 0x02,
+} mali_l2_cache_enable;
+
+/**
+ * Mali L2 cache status bits
+ */
+typedef enum mali_l2_cache_status {
+	MALI400_L2_CACHE_STATUS_COMMAND_BUSY = 0x01,
+	MALI400_L2_CACHE_STATUS_DATA_BUSY    = 0x02,
+} mali_l2_cache_status;
+
+#define MALI400_L2_MAX_READS_NOT_SET -1
+
+static struct mali_l2_cache_core *
+	mali_global_l2s[MALI_MAX_NUMBER_OF_L2_CACHE_CORES] = { NULL, };
+static u32 mali_global_num_l2s = 0;
+
+int mali_l2_max_reads = MALI400_L2_MAX_READS_NOT_SET;
+
+
+/* Local helper functions */
+
+static void mali_l2_cache_reset(struct mali_l2_cache_core *cache);
+
+static _mali_osk_errcode_t mali_l2_cache_send_command(
+	struct mali_l2_cache_core *cache, u32 reg, u32 val);
+
+static void mali_l2_cache_lock(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	_mali_osk_spinlock_irq_lock(cache->lock);
+}
+
+static void mali_l2_cache_unlock(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	_mali_osk_spinlock_irq_unlock(cache->lock);
+}
+
+/* Implementation of the L2 cache interface */
+
+struct mali_l2_cache_core *mali_l2_cache_create(
+	_mali_osk_resource_t *resource, u32 domain_index)
+{
+	struct mali_l2_cache_core *cache = NULL;
+#if defined(DEBUG)
+	u32 cache_size;
+#endif
+
+	MALI_DEBUG_PRINT(4, ("Mali L2 cache: Creating Mali L2 cache: %s\n",
+			     resource->description));
+
+	if (mali_global_num_l2s >= MALI_MAX_NUMBER_OF_L2_CACHE_CORES) {
+		MALI_PRINT_ERROR(("Mali L2 cache: Too many L2 caches\n"));
+		return NULL;
+	}
+
+	cache = _mali_osk_malloc(sizeof(struct mali_l2_cache_core));
+	if (NULL == cache) {
+		MALI_PRINT_ERROR(("Mali L2 cache: Failed to allocate memory for L2 cache core\n"));
+		return NULL;
+	}
+
+	cache->core_id =  mali_global_num_l2s;
+	cache->counter_src0 = MALI_HW_CORE_NO_COUNTER;
+	cache->counter_src1 = MALI_HW_CORE_NO_COUNTER;
+	cache->counter_value0_base = 0;
+	cache->counter_value1_base = 0;
+	cache->pm_domain = NULL;
+	cache->power_is_on = MALI_FALSE;
+	cache->last_invalidated_id = 0;
+
+	if (_MALI_OSK_ERR_OK != mali_hw_core_create(&cache->hw_core,
+			resource, MALI400_L2_CACHE_REGISTERS_SIZE)) {
+		_mali_osk_free(cache);
+		return NULL;
+	}
+
+#if defined(DEBUG)
+	cache_size = mali_hw_core_register_read(&cache->hw_core,
+						MALI400_L2_CACHE_REGISTER_SIZE);
+	MALI_DEBUG_PRINT(2, ("Mali L2 cache: Created %s: % 3uK, %u-way, % 2ubyte cache line, % 3ubit external bus\n",
+			     resource->description,
+			     1 << (((cache_size >> 16) & 0xff) - 10),
+			     1 << ((cache_size >> 8) & 0xff),
+			     1 << (cache_size & 0xff),
+			     1 << ((cache_size >> 24) & 0xff)));
+#endif
+
+	cache->lock = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_ORDERED,
+			_MALI_OSK_LOCK_ORDER_L2);
+	if (NULL == cache->lock) {
+		MALI_PRINT_ERROR(("Mali L2 cache: Failed to create counter lock for L2 cache core %s\n",
+				  cache->hw_core.description));
+		mali_hw_core_delete(&cache->hw_core);
+		_mali_osk_free(cache);
+		return NULL;
+	}
+
+	/* register with correct power domain */
+	cache->pm_domain = mali_pm_register_l2_cache(
+				   domain_index, cache);
+
+	mali_global_l2s[mali_global_num_l2s] = cache;
+	mali_global_num_l2s++;
+
+	return cache;
+}
+
+void mali_l2_cache_delete(struct mali_l2_cache_core *cache)
+{
+	u32 i;
+	for (i = 0; i < mali_global_num_l2s; i++) {
+		if (mali_global_l2s[i] != cache) {
+			continue;
+		}
+
+		mali_global_l2s[i] = NULL;
+		mali_global_num_l2s--;
+
+		if (i == mali_global_num_l2s) {
+			/* Removed last element, nothing more to do */
+			break;
+		}
+
+		/*
+		 * We removed a l2 cache from the middle of the array,
+		 * so move the last l2 cache to current position
+		 */
+		mali_global_l2s[i] = mali_global_l2s[mali_global_num_l2s];
+		mali_global_l2s[mali_global_num_l2s] = NULL;
+
+		/* All good */
+		break;
+	}
+
+	_mali_osk_spinlock_irq_term(cache->lock);
+	mali_hw_core_delete(&cache->hw_core);
+	_mali_osk_free(cache);
+}
+
+void mali_l2_cache_power_up(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+
+	mali_l2_cache_lock(cache);
+
+	mali_l2_cache_reset(cache);
+
+	if ((1 << MALI_DOMAIN_INDEX_DUMMY) != cache->pm_domain->pmu_mask)
+		MALI_DEBUG_ASSERT(MALI_FALSE == cache->power_is_on);
+	cache->power_is_on = MALI_TRUE;
+
+	mali_l2_cache_unlock(cache);
+}
+
+void mali_l2_cache_power_down(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+
+	mali_l2_cache_lock(cache);
+
+	MALI_DEBUG_ASSERT(MALI_TRUE == cache->power_is_on);
+
+	/*
+	 * The HW counters will start from zero again when we resume,
+	 * but we should report counters as always increasing.
+	 * Take a copy of the HW values now in order to add this to
+	 * the values we report after being powered up.
+	 *
+	 * The physical power off of the L2 cache might be outside our
+	 * own control (e.g. runtime PM). That is why we must manually
+	 * set set the counter value to zero as well.
+	 */
+
+	if (cache->counter_src0 != MALI_HW_CORE_NO_COUNTER) {
+		cache->counter_value0_base += mali_hw_core_register_read(
+						      &cache->hw_core,
+						      MALI400_L2_CACHE_REGISTER_PERFCNT_VAL0);
+		mali_hw_core_register_write(&cache->hw_core,
+					    MALI400_L2_CACHE_REGISTER_PERFCNT_VAL0, 0);
+	}
+
+	if (cache->counter_src1 != MALI_HW_CORE_NO_COUNTER) {
+		cache->counter_value1_base += mali_hw_core_register_read(
+						      &cache->hw_core,
+						      MALI400_L2_CACHE_REGISTER_PERFCNT_VAL1);
+		mali_hw_core_register_write(&cache->hw_core,
+					    MALI400_L2_CACHE_REGISTER_PERFCNT_VAL1, 0);
+	}
+
+
+	cache->power_is_on = MALI_FALSE;
+
+	mali_l2_cache_unlock(cache);
+}
+
+void mali_l2_cache_core_set_counter_src(
+	struct mali_l2_cache_core *cache, u32 source_id, u32 counter)
+{
+	u32 reg_offset_src;
+	u32 reg_offset_val;
+
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	MALI_DEBUG_ASSERT(source_id >= 0 && source_id <= 1);
+
+	mali_l2_cache_lock(cache);
+
+	if (0 == source_id) {
+		/* start counting from 0 */
+		cache->counter_value0_base = 0;
+		cache->counter_src0 = counter;
+		reg_offset_src = MALI400_L2_CACHE_REGISTER_PERFCNT_SRC0;
+		reg_offset_val = MALI400_L2_CACHE_REGISTER_PERFCNT_VAL0;
+	} else {
+		/* start counting from 0 */
+		cache->counter_value1_base = 0;
+		cache->counter_src1 = counter;
+		reg_offset_src = MALI400_L2_CACHE_REGISTER_PERFCNT_SRC1;
+		reg_offset_val = MALI400_L2_CACHE_REGISTER_PERFCNT_VAL1;
+	}
+
+	if (cache->power_is_on) {
+		u32 hw_src;
+
+		if (MALI_HW_CORE_NO_COUNTER != counter) {
+			hw_src = counter;
+		} else {
+			hw_src = 0; /* disable value for HW */
+		}
+
+		/* Set counter src */
+		mali_hw_core_register_write(&cache->hw_core,
+					    reg_offset_src, hw_src);
+
+		/* Make sure the HW starts counting from 0 again */
+		mali_hw_core_register_write(&cache->hw_core,
+					    reg_offset_val, 0);
+	}
+
+	mali_l2_cache_unlock(cache);
+}
+
+void mali_l2_cache_core_get_counter_values(
+	struct mali_l2_cache_core *cache,
+	u32 *src0, u32 *value0, u32 *src1, u32 *value1)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	MALI_DEBUG_ASSERT(NULL != src0);
+	MALI_DEBUG_ASSERT(NULL != value0);
+	MALI_DEBUG_ASSERT(NULL != src1);
+	MALI_DEBUG_ASSERT(NULL != value1);
+
+	mali_l2_cache_lock(cache);
+
+	*src0 = cache->counter_src0;
+	*src1 = cache->counter_src1;
+
+	if (cache->counter_src0 != MALI_HW_CORE_NO_COUNTER) {
+		if (MALI_TRUE == cache->power_is_on) {
+			*value0 = mali_hw_core_register_read(&cache->hw_core,
+							     MALI400_L2_CACHE_REGISTER_PERFCNT_VAL0);
+		} else {
+			*value0 = 0;
+		}
+
+		/* Add base offset value (in case we have been power off) */
+		*value0 += cache->counter_value0_base;
+	}
+
+	if (cache->counter_src1 != MALI_HW_CORE_NO_COUNTER) {
+		if (MALI_TRUE == cache->power_is_on) {
+			*value1 = mali_hw_core_register_read(&cache->hw_core,
+							     MALI400_L2_CACHE_REGISTER_PERFCNT_VAL1);
+		} else {
+			*value1 = 0;
+		}
+
+		/* Add base offset value (in case we have been power off) */
+		*value1 += cache->counter_value1_base;
+	}
+
+	mali_l2_cache_unlock(cache);
+}
+
+struct mali_l2_cache_core *mali_l2_cache_core_get_glob_l2_core(u32 index)
+{
+	if (mali_global_num_l2s > index) {
+		return mali_global_l2s[index];
+	}
+
+	return NULL;
+}
+
+u32 mali_l2_cache_core_get_glob_num_l2_cores(void)
+{
+	return mali_global_num_l2s;
+}
+
+void mali_l2_cache_invalidate(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+
+	if (NULL == cache) {
+		return;
+	}
+
+	mali_l2_cache_lock(cache);
+
+	cache->last_invalidated_id = mali_scheduler_get_new_cache_order();
+	mali_l2_cache_send_command(cache, MALI400_L2_CACHE_REGISTER_COMMAND,
+				   MALI400_L2_CACHE_COMMAND_CLEAR_ALL);
+
+	mali_l2_cache_unlock(cache);
+}
+
+void mali_l2_cache_invalidate_conditional(
+	struct mali_l2_cache_core *cache, u32 id)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+
+	if (NULL == cache) {
+		return;
+	}
+
+	/*
+	 * If the last cache invalidation was done by a job with a higher id we
+	 * don't have to flush. Since user space will store jobs w/ their
+	 * corresponding memory in sequence (first job #0, then job #1, ...),
+	 * we don't have to flush for job n-1 if job n has already invalidated
+	 * the cache since we know for sure that job n-1's memory was already
+	 * written when job n was started.
+	 */
+
+	mali_l2_cache_lock(cache);
+
+	if (((s32)id) > ((s32)cache->last_invalidated_id)) {
+		/* Set latest invalidated id to current "point in time" */
+		cache->last_invalidated_id =
+			mali_scheduler_get_new_cache_order();
+		mali_l2_cache_send_command(cache,
+					   MALI400_L2_CACHE_REGISTER_COMMAND,
+					   MALI400_L2_CACHE_COMMAND_CLEAR_ALL);
+	}
+
+	mali_l2_cache_unlock(cache);
+}
+
+void mali_l2_cache_invalidate_all(void)
+{
+	u32 i;
+	for (i = 0; i < mali_global_num_l2s; i++) {
+		struct mali_l2_cache_core *cache = mali_global_l2s[i];
+		_mali_osk_errcode_t ret;
+
+		MALI_DEBUG_ASSERT_POINTER(cache);
+
+		mali_l2_cache_lock(cache);
+
+		if (MALI_TRUE != cache->power_is_on) {
+			mali_l2_cache_unlock(cache);
+			continue;
+		}
+
+		cache->last_invalidated_id =
+			mali_scheduler_get_new_cache_order();
+
+		ret = mali_l2_cache_send_command(cache,
+						 MALI400_L2_CACHE_REGISTER_COMMAND,
+						 MALI400_L2_CACHE_COMMAND_CLEAR_ALL);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_PRINT_ERROR(("Failed to invalidate cache\n"));
+		}
+
+		mali_l2_cache_unlock(cache);
+	}
+}
+
+void mali_l2_cache_invalidate_all_pages(u32 *pages, u32 num_pages)
+{
+	u32 i;
+	for (i = 0; i < mali_global_num_l2s; i++) {
+		struct mali_l2_cache_core *cache = mali_global_l2s[i];
+		u32 j;
+
+		MALI_DEBUG_ASSERT_POINTER(cache);
+
+		mali_l2_cache_lock(cache);
+
+		if (MALI_TRUE != cache->power_is_on) {
+			mali_l2_cache_unlock(cache);
+			continue;
+		}
+
+		for (j = 0; j < num_pages; j++) {
+			_mali_osk_errcode_t ret;
+
+			ret = mali_l2_cache_send_command(cache,
+							 MALI400_L2_CACHE_REGISTER_CLEAR_PAGE,
+							 pages[j]);
+			if (_MALI_OSK_ERR_OK != ret) {
+				MALI_PRINT_ERROR(("Failed to invalidate cache (page)\n"));
+			}
+		}
+
+		mali_l2_cache_unlock(cache);
+	}
+}
+
+/* -------- local helper functions below -------- */
+
+static void mali_l2_cache_reset(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	MALI_DEBUG_ASSERT_LOCK_HELD(cache->lock);
+
+	/* Invalidate cache (just to keep it in a known state at startup) */
+	mali_l2_cache_send_command(cache, MALI400_L2_CACHE_REGISTER_COMMAND,
+				   MALI400_L2_CACHE_COMMAND_CLEAR_ALL);
+
+	/* Enable cache */
+	mali_hw_core_register_write(&cache->hw_core,
+				    MALI400_L2_CACHE_REGISTER_ENABLE,
+				    (u32)MALI400_L2_CACHE_ENABLE_ACCESS |
+				    (u32)MALI400_L2_CACHE_ENABLE_READ_ALLOCATE);
+
+	if (MALI400_L2_MAX_READS_NOT_SET != mali_l2_max_reads) {
+		mali_hw_core_register_write(&cache->hw_core,
+					    MALI400_L2_CACHE_REGISTER_MAX_READS,
+					    (u32)mali_l2_max_reads);
+	}
+
+	/* Restart any performance counters (if enabled) */
+	if (cache->counter_src0 != MALI_HW_CORE_NO_COUNTER) {
+
+		mali_hw_core_register_write(&cache->hw_core,
+					    MALI400_L2_CACHE_REGISTER_PERFCNT_SRC0,
+					    cache->counter_src0);
+	}
+
+	if (cache->counter_src1 != MALI_HW_CORE_NO_COUNTER) {
+		mali_hw_core_register_write(&cache->hw_core,
+					    MALI400_L2_CACHE_REGISTER_PERFCNT_SRC1,
+					    cache->counter_src1);
+	}
+}
+
+static _mali_osk_errcode_t mali_l2_cache_send_command(
+	struct mali_l2_cache_core *cache, u32 reg, u32 val)
+{
+	int i = 0;
+	const int loop_count = 100000;
+
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	MALI_DEBUG_ASSERT_LOCK_HELD(cache->lock);
+
+	/*
+	 * First, wait for L2 cache command handler to go idle.
+	 * (Commands received while processing another command will be ignored)
+	 */
+	for (i = 0; i < loop_count; i++) {
+		if (!(mali_hw_core_register_read(&cache->hw_core,
+						 MALI400_L2_CACHE_REGISTER_STATUS) &
+		      (u32)MALI400_L2_CACHE_STATUS_COMMAND_BUSY)) {
+			break;
+		}
+	}
+
+	if (i == loop_count) {
+		MALI_DEBUG_PRINT(1, ("Mali L2 cache: aborting wait for command interface to go idle\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* then issue the command */
+	mali_hw_core_register_write(&cache->hw_core, reg, val);
+
+	return _MALI_OSK_ERR_OK;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_l2_cache.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_l2_cache.h
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_KERNEL_L2_CACHE_H__
+#define __MALI_KERNEL_L2_CACHE_H__
+
+#include "mali_osk.h"
+#include "mali_hw_core.h"
+
+#define MALI_MAX_NUMBER_OF_L2_CACHE_CORES  3
+/* Maximum 1 GP and 4 PP for an L2 cache core (Mali-400 MP4) */
+#define MALI_MAX_NUMBER_OF_GROUPS_PER_L2_CACHE 5
+
+/**
+ * Definition of the L2 cache core struct
+ * Used to track a L2 cache unit in the system.
+ * Contains information about the mapping of the registers
+ */
+struct mali_l2_cache_core {
+	/* Common HW core functionality */
+	struct mali_hw_core hw_core;
+
+	/* Synchronize L2 cache access */
+	_mali_osk_spinlock_irq_t *lock;
+
+	/* Unique core ID */
+	u32 core_id;
+
+	/* The power domain this L2 cache belongs to */
+	struct mali_pm_domain *pm_domain;
+
+	/* MALI_TRUE if power is on for this L2 cache */
+	mali_bool power_is_on;
+
+	/* A "timestamp" to avoid unnecessary flushes */
+	u32 last_invalidated_id;
+
+	/* Performance counter 0, MALI_HW_CORE_NO_COUNTER for disabled */
+	u32 counter_src0;
+
+	/* Performance counter 1, MALI_HW_CORE_NO_COUNTER for disabled */
+	u32 counter_src1;
+
+	/*
+	 * Performance counter 0 value base/offset
+	 * (allows accumulative reporting even after power off)
+	 */
+	u32 counter_value0_base;
+
+	/*
+	 * Performance counter 0 value base/offset
+	 * (allows accumulative reporting even after power off)
+	 */
+	u32 counter_value1_base;
+
+	/* Used by PM domains to link L2 caches of same domain */
+	_mali_osk_list_t pm_domain_list;
+};
+
+_mali_osk_errcode_t mali_l2_cache_initialize(void);
+void mali_l2_cache_terminate(void);
+
+struct mali_l2_cache_core *mali_l2_cache_create(
+	_mali_osk_resource_t *resource, u32 domain_index);
+void mali_l2_cache_delete(struct mali_l2_cache_core *cache);
+
+MALI_STATIC_INLINE u32 mali_l2_cache_get_id(struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	return cache->core_id;
+}
+
+MALI_STATIC_INLINE struct mali_pm_domain *mali_l2_cache_get_pm_domain(
+	struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	return cache->pm_domain;
+}
+
+void mali_l2_cache_power_up(struct mali_l2_cache_core *cache);
+void mali_l2_cache_power_down(struct mali_l2_cache_core *cache);
+
+void mali_l2_cache_core_set_counter_src(
+	struct mali_l2_cache_core *cache, u32 source_id, u32 counter);
+
+MALI_STATIC_INLINE u32 mali_l2_cache_core_get_counter_src0(
+	struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	return cache->counter_src0;
+}
+
+MALI_STATIC_INLINE u32 mali_l2_cache_core_get_counter_src1(
+	struct mali_l2_cache_core *cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(cache);
+	return cache->counter_src1;
+}
+
+void mali_l2_cache_core_get_counter_values(
+	struct mali_l2_cache_core *cache,
+	u32 *src0, u32 *value0, u32 *src1, u32 *value1);
+
+struct mali_l2_cache_core *mali_l2_cache_core_get_glob_l2_core(u32 index);
+u32 mali_l2_cache_core_get_glob_num_l2_cores(void);
+
+struct mali_group *mali_l2_cache_get_group(
+	struct mali_l2_cache_core *cache, u32 index);
+
+void mali_l2_cache_invalidate(struct mali_l2_cache_core *cache);
+void mali_l2_cache_invalidate_conditional(
+	struct mali_l2_cache_core *cache, u32 id);
+
+void mali_l2_cache_invalidate_all(void);
+void mali_l2_cache_invalidate_all_pages(u32 *pages, u32 num_pages);
+
+#endif /* __MALI_KERNEL_L2_CACHE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_mem_validation.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_mem_validation.c
@@ -0,0 +1,65 @@
+/*
+ * Copyright (C) 2011-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_mem_validation.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+#define MALI_INVALID_MEM_ADDR 0xFFFFFFFF
+
+typedef struct {
+	u32 phys_base;        /**< Mali physical base of the memory, page aligned */
+	u32 size;             /**< size in bytes of the memory, multiple of page size */
+} _mali_mem_validation_t;
+
+static _mali_mem_validation_t mali_mem_validator = { MALI_INVALID_MEM_ADDR, MALI_INVALID_MEM_ADDR };
+
+_mali_osk_errcode_t mali_mem_validation_add_range(u32 start, u32 size)
+{
+	/* Check that no other MEM_VALIDATION resources exist */
+	if (MALI_INVALID_MEM_ADDR != mali_mem_validator.phys_base) {
+		MALI_PRINT_ERROR(("Failed to add frame buffer memory; another range is already specified\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Check restrictions on page alignment */
+	if ((0 != (start & (~_MALI_OSK_CPU_PAGE_MASK))) ||
+	    (0 != (size & (~_MALI_OSK_CPU_PAGE_MASK)))) {
+		MALI_PRINT_ERROR(("Failed to add frame buffer memory; incorrect alignment\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	mali_mem_validator.phys_base = start;
+	mali_mem_validator.size = size;
+	MALI_DEBUG_PRINT(2, ("Memory Validator installed for Mali physical address base=0x%08X, size=0x%08X\n",
+			     mali_mem_validator.phys_base, mali_mem_validator.size));
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_mem_validation_check(u32 phys_addr, u32 size)
+{
+	if (phys_addr < (phys_addr + size)) { /* Don't allow overflow (or zero size) */
+		if ((0 == (phys_addr & (~_MALI_OSK_CPU_PAGE_MASK))) &&
+		    (0 == (size & (~_MALI_OSK_CPU_PAGE_MASK)))) {
+			if ((phys_addr          >= mali_mem_validator.phys_base) &&
+			    ((phys_addr + (size - 1)) >= mali_mem_validator.phys_base) &&
+			    (phys_addr          <= (mali_mem_validator.phys_base + (mali_mem_validator.size - 1))) &&
+			    ((phys_addr + (size - 1)) <= (mali_mem_validator.phys_base + (mali_mem_validator.size - 1)))) {
+				MALI_DEBUG_PRINT(3, ("Accepted range 0x%08X + size 0x%08X (= 0x%08X)\n", phys_addr, size, (phys_addr + size - 1)));
+				return _MALI_OSK_ERR_OK;
+			}
+		}
+	}
+
+	MALI_PRINT_ERROR(("MALI PHYSICAL RANGE VALIDATION ERROR: The range supplied was: phys_base=0x%08X, size=0x%08X\n", phys_addr, size));
+
+	return _MALI_OSK_ERR_FAULT;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_mem_validation.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_mem_validation.h
@@ -0,0 +1,19 @@
+/*
+ * Copyright (C) 2011-2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEM_VALIDATION_H__
+#define __MALI_MEM_VALIDATION_H__
+
+#include "mali_osk.h"
+
+_mali_osk_errcode_t mali_mem_validation_add_range(u32 start, u32 size);
+_mali_osk_errcode_t mali_mem_validation_check(u32 phys_addr, u32 size);
+
+#endif /* __MALI_MEM_VALIDATION_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_mmu.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_mmu.c
@@ -0,0 +1,433 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_ukk.h"
+
+#include "mali_mmu.h"
+#include "mali_hw_core.h"
+#include "mali_group.h"
+#include "mali_mmu_page_directory.h"
+
+/**
+ * Size of the MMU registers in bytes
+ */
+#define MALI_MMU_REGISTERS_SIZE 0x24
+
+/**
+ * MMU commands
+ * These are the commands that can be sent
+ * to the MMU unit.
+ */
+typedef enum mali_mmu_command {
+	MALI_MMU_COMMAND_ENABLE_PAGING = 0x00, /**< Enable paging (memory translation) */
+	MALI_MMU_COMMAND_DISABLE_PAGING = 0x01, /**< Disable paging (memory translation) */
+	MALI_MMU_COMMAND_ENABLE_STALL = 0x02, /**<  Enable stall on page fault */
+	MALI_MMU_COMMAND_DISABLE_STALL = 0x03, /**< Disable stall on page fault */
+	MALI_MMU_COMMAND_ZAP_CACHE = 0x04, /**< Zap the entire page table cache */
+	MALI_MMU_COMMAND_PAGE_FAULT_DONE = 0x05, /**< Page fault processed */
+	MALI_MMU_COMMAND_HARD_RESET = 0x06 /**< Reset the MMU back to power-on settings */
+} mali_mmu_command;
+
+static void mali_mmu_probe_trigger(void *data);
+static _mali_osk_errcode_t mali_mmu_probe_ack(void *data);
+
+MALI_STATIC_INLINE _mali_osk_errcode_t mali_mmu_raw_reset(struct mali_mmu_core *mmu);
+
+/* page fault queue flush helper pages
+ * note that the mapping pointers are currently unused outside of the initialization functions */
+static mali_dma_addr mali_page_fault_flush_page_directory = MALI_INVALID_PAGE;
+static mali_io_address mali_page_fault_flush_page_directory_mapping = NULL;
+static mali_dma_addr mali_page_fault_flush_page_table = MALI_INVALID_PAGE;
+static mali_io_address mali_page_fault_flush_page_table_mapping = NULL;
+static mali_dma_addr mali_page_fault_flush_data_page = MALI_INVALID_PAGE;
+static mali_io_address mali_page_fault_flush_data_page_mapping = NULL;
+
+/* an empty page directory (no address valid) which is active on any MMU not currently marked as in use */
+static mali_dma_addr mali_empty_page_directory_phys   = MALI_INVALID_PAGE;
+static mali_io_address mali_empty_page_directory_virt = NULL;
+
+
+_mali_osk_errcode_t mali_mmu_initialize(void)
+{
+	/* allocate the helper pages */
+	mali_empty_page_directory_phys = mali_allocate_empty_page(&mali_empty_page_directory_virt);
+	if (0 == mali_empty_page_directory_phys) {
+		MALI_DEBUG_PRINT_ERROR(("Mali MMU: Could not allocate empty page directory.\n"));
+		mali_empty_page_directory_phys = MALI_INVALID_PAGE;
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	if (_MALI_OSK_ERR_OK != mali_create_fault_flush_pages(&mali_page_fault_flush_page_directory,
+			&mali_page_fault_flush_page_directory_mapping,
+			&mali_page_fault_flush_page_table,
+			&mali_page_fault_flush_page_table_mapping,
+			&mali_page_fault_flush_data_page,
+			&mali_page_fault_flush_data_page_mapping)) {
+		MALI_DEBUG_PRINT_ERROR(("Mali MMU: Could not allocate fault flush pages\n"));
+		mali_free_empty_page(mali_empty_page_directory_phys, mali_empty_page_directory_virt);
+		mali_empty_page_directory_phys = MALI_INVALID_PAGE;
+		mali_empty_page_directory_virt = NULL;
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mmu_terminate(void)
+{
+	MALI_DEBUG_PRINT(3, ("Mali MMU: terminating\n"));
+
+	/* Free global helper pages */
+	mali_free_empty_page(mali_empty_page_directory_phys, mali_empty_page_directory_virt);
+	mali_empty_page_directory_phys = MALI_INVALID_PAGE;
+	mali_empty_page_directory_virt = NULL;
+
+	/* Free the page fault flush pages */
+	mali_destroy_fault_flush_pages(&mali_page_fault_flush_page_directory,
+				       &mali_page_fault_flush_page_directory_mapping,
+				       &mali_page_fault_flush_page_table,
+				       &mali_page_fault_flush_page_table_mapping,
+				       &mali_page_fault_flush_data_page,
+				       &mali_page_fault_flush_data_page_mapping);
+}
+
+struct mali_mmu_core *mali_mmu_create(_mali_osk_resource_t *resource, struct mali_group *group, mali_bool is_virtual)
+{
+	struct mali_mmu_core *mmu = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(resource);
+
+	MALI_DEBUG_PRINT(2, ("Mali MMU: Creating Mali MMU: %s\n", resource->description));
+
+	mmu = _mali_osk_calloc(1, sizeof(struct mali_mmu_core));
+	if (NULL != mmu) {
+		if (_MALI_OSK_ERR_OK == mali_hw_core_create(&mmu->hw_core, resource, MALI_MMU_REGISTERS_SIZE)) {
+			if (_MALI_OSK_ERR_OK == mali_group_add_mmu_core(group, mmu)) {
+				if (is_virtual) {
+					/* Skip reset and IRQ setup for virtual MMU */
+					return mmu;
+				}
+
+				if (_MALI_OSK_ERR_OK == mali_mmu_reset(mmu)) {
+					/* Setup IRQ handlers (which will do IRQ probing if needed) */
+					mmu->irq = _mali_osk_irq_init(resource->irq,
+								      mali_group_upper_half_mmu,
+								      group,
+								      mali_mmu_probe_trigger,
+								      mali_mmu_probe_ack,
+								      mmu,
+								      resource->description);
+					if (NULL != mmu->irq) {
+						return mmu;
+					} else {
+						MALI_PRINT_ERROR(("Mali MMU: Failed to setup interrupt handlers for MMU %s\n", mmu->hw_core.description));
+					}
+				}
+				mali_group_remove_mmu_core(group);
+			} else {
+				MALI_PRINT_ERROR(("Mali MMU: Failed to add core %s to group\n", mmu->hw_core.description));
+			}
+			mali_hw_core_delete(&mmu->hw_core);
+		}
+
+		_mali_osk_free(mmu);
+	} else {
+		MALI_PRINT_ERROR(("Failed to allocate memory for MMU\n"));
+	}
+
+	return NULL;
+}
+
+void mali_mmu_delete(struct mali_mmu_core *mmu)
+{
+	if (NULL != mmu->irq) {
+		_mali_osk_irq_term(mmu->irq);
+	}
+
+	mali_hw_core_delete(&mmu->hw_core);
+	_mali_osk_free(mmu);
+}
+
+static void mali_mmu_enable_paging(struct mali_mmu_core *mmu)
+{
+	int i;
+
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_ENABLE_PAGING);
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; ++i) {
+		if (mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS) & MALI_MMU_STATUS_BIT_PAGING_ENABLED) {
+			break;
+		}
+	}
+	if (MALI_REG_POLL_COUNT_FAST == i) {
+		MALI_PRINT_ERROR(("Enable paging request failed, MMU status is 0x%08X\n", mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS)));
+	}
+}
+
+/**
+ * Issues the enable stall command to the MMU and waits for HW to complete the request
+ * @param mmu The MMU to enable paging for
+ * @return MALI_TRUE if HW stall was successfully engaged, otherwise MALI_FALSE (req timed out)
+ */
+static mali_bool mali_mmu_enable_stall(struct mali_mmu_core *mmu)
+{
+	int i;
+	u32 mmu_status = mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS);
+
+	if (0 == (mmu_status & MALI_MMU_STATUS_BIT_PAGING_ENABLED)) {
+		MALI_DEBUG_PRINT(4, ("MMU stall is implicit when Paging is not enabled.\n"));
+		return MALI_TRUE;
+	}
+
+	if (mmu_status & MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE) {
+		MALI_DEBUG_PRINT(3, ("Aborting MMU stall request since it is in pagefault state.\n"));
+		return MALI_FALSE;
+	}
+
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_ENABLE_STALL);
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; ++i) {
+		mmu_status = mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS);
+		if (mmu_status & MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE) {
+			break;
+		}
+		if ((mmu_status & MALI_MMU_STATUS_BIT_STALL_ACTIVE) && (0 == (mmu_status & MALI_MMU_STATUS_BIT_STALL_NOT_ACTIVE))) {
+			break;
+		}
+		if (0 == (mmu_status & (MALI_MMU_STATUS_BIT_PAGING_ENABLED))) {
+			break;
+		}
+	}
+	if (MALI_REG_POLL_COUNT_FAST == i) {
+		MALI_DEBUG_PRINT(2, ("Enable stall request failed, MMU status is 0x%08X\n", mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS)));
+		return MALI_FALSE;
+	}
+
+	if (mmu_status & MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE) {
+		MALI_DEBUG_PRINT(2, ("Aborting MMU stall request since it has a pagefault.\n"));
+		return MALI_FALSE;
+	}
+
+	return MALI_TRUE;
+}
+
+/**
+ * Issues the disable stall command to the MMU and waits for HW to complete the request
+ * @param mmu The MMU to enable paging for
+ */
+static void mali_mmu_disable_stall(struct mali_mmu_core *mmu)
+{
+	int i;
+	u32 mmu_status = mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS);
+
+	if (0 == (mmu_status & MALI_MMU_STATUS_BIT_PAGING_ENABLED)) {
+		MALI_DEBUG_PRINT(3, ("MMU disable skipped since it was not enabled.\n"));
+		return;
+	}
+	if (mmu_status & MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE) {
+		MALI_DEBUG_PRINT(2, ("Aborting MMU disable stall request since it is in pagefault state.\n"));
+		return;
+	}
+
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_DISABLE_STALL);
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; ++i) {
+		u32 status = mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS);
+		if (0 == (status & MALI_MMU_STATUS_BIT_STALL_ACTIVE)) {
+			break;
+		}
+		if (status &  MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE) {
+			break;
+		}
+		if (0 == (mmu_status & MALI_MMU_STATUS_BIT_PAGING_ENABLED)) {
+			break;
+		}
+	}
+	if (MALI_REG_POLL_COUNT_FAST == i) MALI_DEBUG_PRINT(1, ("Disable stall request failed, MMU status is 0x%08X\n", mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS)));
+}
+
+void mali_mmu_page_fault_done(struct mali_mmu_core *mmu)
+{
+	MALI_DEBUG_PRINT(4, ("Mali MMU: %s: Leaving page fault mode\n", mmu->hw_core.description));
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_PAGE_FAULT_DONE);
+}
+
+MALI_STATIC_INLINE _mali_osk_errcode_t mali_mmu_raw_reset(struct mali_mmu_core *mmu)
+{
+	int i;
+
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_DTE_ADDR, 0xCAFEBABE);
+	MALI_DEBUG_ASSERT(0xCAFEB000 == mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_DTE_ADDR));
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_HARD_RESET);
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; ++i) {
+		if (mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_DTE_ADDR) == 0) {
+			break;
+		}
+	}
+	if (MALI_REG_POLL_COUNT_FAST == i) {
+		MALI_PRINT_ERROR(("Reset request failed, MMU status is 0x%08X\n", mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS)));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_mmu_reset(struct mali_mmu_core *mmu)
+{
+	_mali_osk_errcode_t err = _MALI_OSK_ERR_FAULT;
+	mali_bool stall_success;
+	MALI_DEBUG_ASSERT_POINTER(mmu);
+
+	stall_success = mali_mmu_enable_stall(mmu);
+	if (!stall_success) {
+		err = _MALI_OSK_ERR_BUSY;
+	}
+
+	MALI_DEBUG_PRINT(3, ("Mali MMU: mali_kernel_mmu_reset: %s\n", mmu->hw_core.description));
+
+	if (_MALI_OSK_ERR_OK == mali_mmu_raw_reset(mmu)) {
+		mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_INT_MASK, MALI_MMU_INTERRUPT_PAGE_FAULT | MALI_MMU_INTERRUPT_READ_BUS_ERROR);
+		/* no session is active, so just activate the empty page directory */
+		mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_DTE_ADDR, mali_empty_page_directory_phys);
+		mali_mmu_enable_paging(mmu);
+		err = _MALI_OSK_ERR_OK;
+	}
+	mali_mmu_disable_stall(mmu);
+
+	return err;
+}
+
+mali_bool mali_mmu_zap_tlb(struct mali_mmu_core *mmu)
+{
+	mali_bool stall_success = mali_mmu_enable_stall(mmu);
+
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_ZAP_CACHE);
+
+	if (MALI_FALSE == stall_success) {
+		/* False means that it is in Pagefault state. Not possible to disable_stall then */
+		return MALI_FALSE;
+	}
+
+	mali_mmu_disable_stall(mmu);
+	return MALI_TRUE;
+}
+
+void mali_mmu_zap_tlb_without_stall(struct mali_mmu_core *mmu)
+{
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_ZAP_CACHE);
+}
+
+
+void mali_mmu_invalidate_page(struct mali_mmu_core *mmu, u32 mali_address)
+{
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_ZAP_ONE_LINE, MALI_MMU_PDE_ENTRY(mali_address));
+}
+
+static void mali_mmu_activate_address_space(struct mali_mmu_core *mmu, u32 page_directory)
+{
+	/* The MMU must be in stalled or page fault mode, for this writing to work */
+	MALI_DEBUG_ASSERT(0 != (mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS)
+				& (MALI_MMU_STATUS_BIT_STALL_ACTIVE | MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE)));
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_DTE_ADDR, page_directory);
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_COMMAND, MALI_MMU_COMMAND_ZAP_CACHE);
+
+}
+
+void mali_mmu_activate_page_directory(struct mali_mmu_core *mmu, struct mali_page_directory *pagedir)
+{
+	mali_bool stall_success;
+	MALI_DEBUG_ASSERT_POINTER(mmu);
+
+	MALI_DEBUG_PRINT(5, ("Asked to activate page directory 0x%x on MMU %s\n", pagedir, mmu->hw_core.description));
+
+	stall_success = mali_mmu_enable_stall(mmu);
+	MALI_DEBUG_ASSERT(stall_success);
+	MALI_IGNORE(stall_success);
+	mali_mmu_activate_address_space(mmu, pagedir->page_directory);
+	mali_mmu_disable_stall(mmu);
+}
+
+void mali_mmu_activate_empty_page_directory(struct mali_mmu_core *mmu)
+{
+	mali_bool stall_success;
+
+	MALI_DEBUG_ASSERT_POINTER(mmu);
+	MALI_DEBUG_PRINT(3, ("Activating the empty page directory on MMU %s\n", mmu->hw_core.description));
+
+	stall_success = mali_mmu_enable_stall(mmu);
+
+	/* This function can only be called when the core is idle, so it could not fail. */
+	MALI_DEBUG_ASSERT(stall_success);
+	MALI_IGNORE(stall_success);
+
+	mali_mmu_activate_address_space(mmu, mali_empty_page_directory_phys);
+	mali_mmu_disable_stall(mmu);
+}
+
+void mali_mmu_activate_fault_flush_page_directory(struct mali_mmu_core *mmu)
+{
+	mali_bool stall_success;
+	MALI_DEBUG_ASSERT_POINTER(mmu);
+
+	MALI_DEBUG_PRINT(3, ("Activating the page fault flush page directory on MMU %s\n", mmu->hw_core.description));
+	stall_success = mali_mmu_enable_stall(mmu);
+	/* This function is expect to fail the stalling, since it might be in PageFault mode when it is called */
+	mali_mmu_activate_address_space(mmu, mali_page_fault_flush_page_directory);
+	if (MALI_TRUE == stall_success) mali_mmu_disable_stall(mmu);
+}
+
+/* Is called when we want the mmu to give an interrupt */
+static void mali_mmu_probe_trigger(void *data)
+{
+	struct mali_mmu_core *mmu = (struct mali_mmu_core *)data;
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_INT_RAWSTAT, MALI_MMU_INTERRUPT_PAGE_FAULT | MALI_MMU_INTERRUPT_READ_BUS_ERROR);
+}
+
+/* Is called when the irq probe wants the mmu to acknowledge an interrupt from the hw */
+static _mali_osk_errcode_t mali_mmu_probe_ack(void *data)
+{
+	struct mali_mmu_core *mmu = (struct mali_mmu_core *)data;
+	u32 int_stat;
+
+	int_stat = mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_INT_STATUS);
+
+	MALI_DEBUG_PRINT(2, ("mali_mmu_probe_irq_acknowledge: intstat 0x%x\n", int_stat));
+	if (int_stat & MALI_MMU_INTERRUPT_PAGE_FAULT) {
+		MALI_DEBUG_PRINT(2, ("Probe: Page fault detect: PASSED\n"));
+		mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_INT_CLEAR, MALI_MMU_INTERRUPT_PAGE_FAULT);
+	} else {
+		MALI_DEBUG_PRINT(1, ("Probe: Page fault detect: FAILED\n"));
+	}
+
+	if (int_stat & MALI_MMU_INTERRUPT_READ_BUS_ERROR) {
+		MALI_DEBUG_PRINT(2, ("Probe: Bus read error detect: PASSED\n"));
+		mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_INT_CLEAR, MALI_MMU_INTERRUPT_READ_BUS_ERROR);
+	} else {
+		MALI_DEBUG_PRINT(1, ("Probe: Bus read error detect: FAILED\n"));
+	}
+
+	if ((int_stat & (MALI_MMU_INTERRUPT_PAGE_FAULT | MALI_MMU_INTERRUPT_READ_BUS_ERROR)) ==
+	    (MALI_MMU_INTERRUPT_PAGE_FAULT | MALI_MMU_INTERRUPT_READ_BUS_ERROR)) {
+		return _MALI_OSK_ERR_OK;
+	}
+
+	return _MALI_OSK_ERR_FAULT;
+}
+
+#if 0
+void mali_mmu_print_state(struct mali_mmu_core *mmu)
+{
+	MALI_DEBUG_PRINT(2, ("MMU: State of %s is 0x%08x\n", mmu->hw_core.description, mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS)));
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_mmu.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_mmu.h
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MMU_H__
+#define __MALI_MMU_H__
+
+#include "mali_osk.h"
+#include "mali_mmu_page_directory.h"
+#include "mali_hw_core.h"
+
+/* Forward declaration from mali_group.h */
+struct mali_group;
+
+/**
+ * MMU register numbers
+ * Used in the register read/write routines.
+ * See the hardware documentation for more information about each register
+ */
+typedef enum mali_mmu_register {
+	MALI_MMU_REGISTER_DTE_ADDR = 0x0000, /**< Current Page Directory Pointer */
+	MALI_MMU_REGISTER_STATUS = 0x0004, /**< Status of the MMU */
+	MALI_MMU_REGISTER_COMMAND = 0x0008, /**< Command register, used to control the MMU */
+	MALI_MMU_REGISTER_PAGE_FAULT_ADDR = 0x000C, /**< Logical address of the last page fault */
+	MALI_MMU_REGISTER_ZAP_ONE_LINE = 0x010, /**< Used to invalidate the mapping of a single page from the MMU */
+	MALI_MMU_REGISTER_INT_RAWSTAT = 0x0014, /**< Raw interrupt status, all interrupts visible */
+	MALI_MMU_REGISTER_INT_CLEAR = 0x0018, /**< Indicate to the MMU that the interrupt has been received */
+	MALI_MMU_REGISTER_INT_MASK = 0x001C, /**< Enable/disable types of interrupts */
+	MALI_MMU_REGISTER_INT_STATUS = 0x0020 /**< Interrupt status based on the mask */
+} mali_mmu_register;
+
+/**
+ * MMU interrupt register bits
+ * Each cause of the interrupt is reported
+ * through the (raw) interrupt status registers.
+ * Multiple interrupts can be pending, so multiple bits
+ * can be set at once.
+ */
+typedef enum mali_mmu_interrupt {
+	MALI_MMU_INTERRUPT_PAGE_FAULT = 0x01, /**< A page fault occured */
+	MALI_MMU_INTERRUPT_READ_BUS_ERROR = 0x02 /**< A bus read error occured */
+} mali_mmu_interrupt;
+
+typedef enum mali_mmu_status_bits {
+	MALI_MMU_STATUS_BIT_PAGING_ENABLED      = 1 << 0,
+	MALI_MMU_STATUS_BIT_PAGE_FAULT_ACTIVE   = 1 << 1,
+	MALI_MMU_STATUS_BIT_STALL_ACTIVE        = 1 << 2,
+	MALI_MMU_STATUS_BIT_IDLE                = 1 << 3,
+	MALI_MMU_STATUS_BIT_REPLAY_BUFFER_EMPTY = 1 << 4,
+	MALI_MMU_STATUS_BIT_PAGE_FAULT_IS_WRITE = 1 << 5,
+	MALI_MMU_STATUS_BIT_STALL_NOT_ACTIVE    = 1 << 31,
+} mali_mmu_status_bits;
+
+/**
+ * Definition of the MMU struct
+ * Used to track a MMU unit in the system.
+ * Contains information about the mapping of the registers
+ */
+struct mali_mmu_core {
+	struct mali_hw_core hw_core; /**< Common for all HW cores */
+	_mali_osk_irq_t *irq;        /**< IRQ handler */
+};
+
+_mali_osk_errcode_t mali_mmu_initialize(void);
+
+void mali_mmu_terminate(void);
+
+struct mali_mmu_core *mali_mmu_create(_mali_osk_resource_t *resource, struct mali_group *group, mali_bool is_virtual);
+void mali_mmu_delete(struct mali_mmu_core *mmu);
+
+_mali_osk_errcode_t mali_mmu_reset(struct mali_mmu_core *mmu);
+mali_bool mali_mmu_zap_tlb(struct mali_mmu_core *mmu);
+void mali_mmu_zap_tlb_without_stall(struct mali_mmu_core *mmu);
+void mali_mmu_invalidate_page(struct mali_mmu_core *mmu, u32 mali_address);
+
+void mali_mmu_activate_page_directory(struct mali_mmu_core *mmu, struct mali_page_directory *pagedir);
+void mali_mmu_activate_empty_page_directory(struct mali_mmu_core *mmu);
+void mali_mmu_activate_fault_flush_page_directory(struct mali_mmu_core *mmu);
+
+void mali_mmu_page_fault_done(struct mali_mmu_core *mmu);
+
+MALI_STATIC_INLINE enum mali_interrupt_result mali_mmu_get_interrupt_result(struct mali_mmu_core *mmu)
+{
+	u32 rawstat_used = mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_INT_RAWSTAT);
+	if (0 == rawstat_used) {
+		return MALI_INTERRUPT_RESULT_NONE;
+	}
+
+	return MALI_INTERRUPT_RESULT_ERROR;
+}
+
+
+MALI_STATIC_INLINE u32 mali_mmu_get_int_status(struct mali_mmu_core *mmu)
+{
+	return mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_INT_STATUS);
+}
+
+MALI_STATIC_INLINE u32 mali_mmu_get_rawstat(struct mali_mmu_core *mmu)
+{
+	return mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_INT_RAWSTAT);
+}
+
+MALI_STATIC_INLINE void mali_mmu_mask_all_interrupts(struct mali_mmu_core *mmu)
+{
+	mali_hw_core_register_write(&mmu->hw_core, MALI_MMU_REGISTER_INT_MASK, 0);
+}
+
+MALI_STATIC_INLINE u32 mali_mmu_get_status(struct mali_mmu_core *mmu)
+{
+	return mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_STATUS);
+}
+
+MALI_STATIC_INLINE u32 mali_mmu_get_page_fault_addr(struct mali_mmu_core *mmu)
+{
+	return mali_hw_core_register_read(&mmu->hw_core, MALI_MMU_REGISTER_PAGE_FAULT_ADDR);
+}
+
+#endif /* __MALI_MMU_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_mmu_page_directory.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_mmu_page_directory.c
@@ -0,0 +1,495 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_ukk.h"
+#include "mali_uk_types.h"
+#include "mali_mmu_page_directory.h"
+#include "mali_memory.h"
+#include "mali_l2_cache.h"
+
+static _mali_osk_errcode_t fill_page(mali_io_address mapping, u32 data);
+
+u32 mali_allocate_empty_page(mali_io_address *virt_addr)
+{
+	_mali_osk_errcode_t err;
+	mali_io_address mapping;
+	mali_dma_addr address;
+
+	if (_MALI_OSK_ERR_OK != mali_mmu_get_table_page(&address, &mapping)) {
+		/* Allocation failed */
+		MALI_DEBUG_PRINT(2, ("Mali MMU: Failed to get table page for empty pgdir\n"));
+		return 0;
+	}
+
+	MALI_DEBUG_ASSERT_POINTER(mapping);
+
+	err = fill_page(mapping, 0);
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_mmu_release_table_page(address, mapping);
+		MALI_DEBUG_PRINT(2, ("Mali MMU: Failed to zero page\n"));
+		return 0;
+	}
+
+	*virt_addr = mapping;
+	return address;
+}
+
+void mali_free_empty_page(mali_dma_addr address, mali_io_address virt_addr)
+{
+	if (MALI_INVALID_PAGE != address) {
+		mali_mmu_release_table_page(address, virt_addr);
+	}
+}
+
+_mali_osk_errcode_t mali_create_fault_flush_pages(mali_dma_addr *page_directory,
+		mali_io_address *page_directory_mapping,
+		mali_dma_addr *page_table, mali_io_address *page_table_mapping,
+		mali_dma_addr *data_page, mali_io_address *data_page_mapping)
+{
+	_mali_osk_errcode_t err;
+
+	err = mali_mmu_get_table_page(data_page, data_page_mapping);
+	if (_MALI_OSK_ERR_OK == err) {
+		err = mali_mmu_get_table_page(page_table, page_table_mapping);
+		if (_MALI_OSK_ERR_OK == err) {
+			err = mali_mmu_get_table_page(page_directory, page_directory_mapping);
+			if (_MALI_OSK_ERR_OK == err) {
+				fill_page(*data_page_mapping, 0);
+				fill_page(*page_table_mapping, *data_page | MALI_MMU_FLAGS_DEFAULT);
+				fill_page(*page_directory_mapping, *page_table | MALI_MMU_FLAGS_PRESENT);
+				MALI_SUCCESS;
+			}
+			mali_mmu_release_table_page(*page_table, *page_table_mapping);
+			*page_table = MALI_INVALID_PAGE;
+		}
+		mali_mmu_release_table_page(*data_page, *data_page_mapping);
+		*data_page = MALI_INVALID_PAGE;
+	}
+	return err;
+}
+
+void mali_destroy_fault_flush_pages(
+	mali_dma_addr *page_directory, mali_io_address *page_directory_mapping,
+	mali_dma_addr *page_table, mali_io_address *page_table_mapping,
+	mali_dma_addr *data_page, mali_io_address *data_page_mapping)
+{
+	if (MALI_INVALID_PAGE != *page_directory) {
+		mali_mmu_release_table_page(*page_directory, *page_directory_mapping);
+		*page_directory = MALI_INVALID_PAGE;
+		*page_directory_mapping = NULL;
+	}
+
+	if (MALI_INVALID_PAGE != *page_table) {
+		mali_mmu_release_table_page(*page_table, *page_table_mapping);
+		*page_table = MALI_INVALID_PAGE;
+		*page_table_mapping = NULL;
+	}
+
+	if (MALI_INVALID_PAGE != *data_page) {
+		mali_mmu_release_table_page(*data_page, *data_page_mapping);
+		*data_page = MALI_INVALID_PAGE;
+		*data_page_mapping = NULL;
+	}
+}
+
+static _mali_osk_errcode_t fill_page(mali_io_address mapping, u32 data)
+{
+	int i;
+	MALI_DEBUG_ASSERT_POINTER(mapping);
+
+	for (i = 0; i < MALI_MMU_PAGE_SIZE / 4; i++) {
+		_mali_osk_mem_iowrite32_relaxed(mapping, i * sizeof(u32), data);
+	}
+	_mali_osk_mem_barrier();
+	MALI_SUCCESS;
+}
+
+_mali_osk_errcode_t mali_mmu_pagedir_map(struct mali_page_directory *pagedir, u32 mali_address, u32 size)
+{
+	const int first_pde = MALI_MMU_PDE_ENTRY(mali_address);
+	const int last_pde = MALI_MMU_PDE_ENTRY(mali_address + size - 1);
+	_mali_osk_errcode_t err;
+	mali_io_address pde_mapping;
+	mali_dma_addr pde_phys;
+	int i, page_count;
+	u32 start_address;
+	if (last_pde < first_pde)
+		return _MALI_OSK_ERR_INVALID_ARGS;
+
+	for (i = first_pde; i <= last_pde; i++) {
+		if (0 == (_mali_osk_mem_ioread32(pagedir->page_directory_mapped,
+						 i * sizeof(u32)) & MALI_MMU_FLAGS_PRESENT)) {
+			/* Page table not present */
+			MALI_DEBUG_ASSERT(0 == pagedir->page_entries_usage_count[i]);
+			MALI_DEBUG_ASSERT(NULL == pagedir->page_entries_mapped[i]);
+
+			err = mali_mmu_get_table_page(&pde_phys, &pde_mapping);
+			if (_MALI_OSK_ERR_OK != err) {
+				MALI_PRINT_ERROR(("Failed to allocate page table page.\n"));
+				return err;
+			}
+			pagedir->page_entries_mapped[i] = pde_mapping;
+
+			/* Update PDE, mark as present */
+			_mali_osk_mem_iowrite32_relaxed(pagedir->page_directory_mapped, i * sizeof(u32),
+							pde_phys | MALI_MMU_FLAGS_PRESENT);
+
+			MALI_DEBUG_ASSERT(0 == pagedir->page_entries_usage_count[i]);
+		}
+
+		if (first_pde == last_pde) {
+			pagedir->page_entries_usage_count[i] += size / MALI_MMU_PAGE_SIZE;
+		} else if (i == first_pde) {
+			start_address = i * MALI_MMU_VIRTUAL_PAGE_SIZE;
+			page_count = (start_address + MALI_MMU_VIRTUAL_PAGE_SIZE - mali_address) / MALI_MMU_PAGE_SIZE;
+			pagedir->page_entries_usage_count[i] += page_count;
+		} else if (i == last_pde) {
+			start_address = i * MALI_MMU_VIRTUAL_PAGE_SIZE;
+			page_count = (mali_address + size - start_address) / MALI_MMU_PAGE_SIZE;
+			pagedir->page_entries_usage_count[i] += page_count;
+		} else {
+			pagedir->page_entries_usage_count[i] = 1024;
+		}
+	}
+	_mali_osk_write_mem_barrier();
+
+	return _MALI_OSK_ERR_OK;
+}
+
+MALI_STATIC_INLINE void mali_mmu_zero_pte(mali_io_address page_table, u32 mali_address, u32 size)
+{
+	int i;
+	const int first_pte = MALI_MMU_PTE_ENTRY(mali_address);
+	const int last_pte = MALI_MMU_PTE_ENTRY(mali_address + size - 1);
+
+	for (i = first_pte; i <= last_pte; i++) {
+		_mali_osk_mem_iowrite32_relaxed(page_table, i * sizeof(u32), 0);
+	}
+}
+
+static u32 mali_page_directory_get_phys_address(struct mali_page_directory *pagedir, u32 index)
+{
+	return (_mali_osk_mem_ioread32(pagedir->page_directory_mapped,
+				       index * sizeof(u32)) & ~MALI_MMU_FLAGS_MASK);
+}
+
+
+_mali_osk_errcode_t mali_mmu_pagedir_unmap(struct mali_page_directory *pagedir, u32 mali_address, u32 size)
+{
+	const int first_pde = MALI_MMU_PDE_ENTRY(mali_address);
+	const int last_pde = MALI_MMU_PDE_ENTRY(mali_address + size - 1);
+	u32 left = size;
+	int i;
+	mali_bool pd_changed = MALI_FALSE;
+	u32 pages_to_invalidate[3]; /* hard-coded to 3: max two pages from the PT level plus max one page from PD level */
+	u32 num_pages_inv = 0;
+	mali_bool invalidate_all = MALI_FALSE; /* safety mechanism in case page_entries_usage_count is unreliable */
+
+	/* For all page directory entries in range. */
+	for (i = first_pde; i <= last_pde; i++) {
+		u32 size_in_pde, offset;
+
+		MALI_DEBUG_ASSERT_POINTER(pagedir->page_entries_mapped[i]);
+		MALI_DEBUG_ASSERT(0 != pagedir->page_entries_usage_count[i]);
+
+		/* Offset into page table, 0 if mali_address is 4MiB aligned */
+		offset = (mali_address & (MALI_MMU_VIRTUAL_PAGE_SIZE - 1));
+		if (left < MALI_MMU_VIRTUAL_PAGE_SIZE - offset) {
+			size_in_pde = left;
+		} else {
+			size_in_pde = MALI_MMU_VIRTUAL_PAGE_SIZE - offset;
+		}
+
+		pagedir->page_entries_usage_count[i] -= size_in_pde / MALI_MMU_PAGE_SIZE;
+
+		/* If entire page table is unused, free it */
+		if (0 == pagedir->page_entries_usage_count[i]) {
+			u32 page_phys;
+			void *page_virt;
+			MALI_DEBUG_PRINT(4, ("Releasing page table as this is the last reference\n"));
+			/* last reference removed, no need to zero out each PTE  */
+
+			page_phys = MALI_MMU_ENTRY_ADDRESS(_mali_osk_mem_ioread32(pagedir->page_directory_mapped, i * sizeof(u32)));
+			page_virt = pagedir->page_entries_mapped[i];
+			pagedir->page_entries_mapped[i] = NULL;
+			_mali_osk_mem_iowrite32_relaxed(pagedir->page_directory_mapped, i * sizeof(u32), 0);
+
+			mali_mmu_release_table_page(page_phys, page_virt);
+			pd_changed = MALI_TRUE;
+		} else {
+			MALI_DEBUG_ASSERT(num_pages_inv < 2);
+			if (num_pages_inv < 2) {
+				pages_to_invalidate[num_pages_inv] = mali_page_directory_get_phys_address(pagedir, i);
+				num_pages_inv++;
+			} else {
+				invalidate_all = MALI_TRUE;
+			}
+
+			/* If part of the page table is still in use, zero the relevant PTEs */
+			mali_mmu_zero_pte(pagedir->page_entries_mapped[i], mali_address, size_in_pde);
+		}
+
+		left -= size_in_pde;
+		mali_address += size_in_pde;
+	}
+	_mali_osk_write_mem_barrier();
+
+	/* L2 pages invalidation */
+	if (MALI_TRUE == pd_changed) {
+		MALI_DEBUG_ASSERT(num_pages_inv < 3);
+		if (num_pages_inv < 3) {
+			pages_to_invalidate[num_pages_inv] = pagedir->page_directory;
+			num_pages_inv++;
+		} else {
+			invalidate_all = MALI_TRUE;
+		}
+	}
+
+	if (invalidate_all) {
+		mali_l2_cache_invalidate_all();
+	} else {
+		mali_l2_cache_invalidate_all_pages(pages_to_invalidate, num_pages_inv);
+	}
+
+	MALI_SUCCESS;
+}
+
+struct mali_page_directory *mali_mmu_pagedir_alloc(void)
+{
+	struct mali_page_directory *pagedir;
+	_mali_osk_errcode_t err;
+	mali_dma_addr phys;
+
+	pagedir = _mali_osk_calloc(1, sizeof(struct mali_page_directory));
+	if (NULL == pagedir) {
+		return NULL;
+	}
+
+	err = mali_mmu_get_table_page(&phys, &pagedir->page_directory_mapped);
+	if (_MALI_OSK_ERR_OK != err) {
+		_mali_osk_free(pagedir);
+		return NULL;
+	}
+
+	pagedir->page_directory = (u32)phys;
+
+	/* Zero page directory */
+	fill_page(pagedir->page_directory_mapped, 0);
+
+	return pagedir;
+}
+
+void mali_mmu_pagedir_free(struct mali_page_directory *pagedir)
+{
+	const int num_page_table_entries = sizeof(pagedir->page_entries_mapped) / sizeof(pagedir->page_entries_mapped[0]);
+	int i;
+
+	/* Free referenced page tables and zero PDEs. */
+	for (i = 0; i < num_page_table_entries; i++) {
+		if (pagedir->page_directory_mapped && (_mali_osk_mem_ioread32(
+				pagedir->page_directory_mapped,
+				sizeof(u32)*i) & MALI_MMU_FLAGS_PRESENT)) {
+			mali_dma_addr phys = _mali_osk_mem_ioread32(pagedir->page_directory_mapped,
+					     i * sizeof(u32)) & ~MALI_MMU_FLAGS_MASK;
+			_mali_osk_mem_iowrite32_relaxed(pagedir->page_directory_mapped, i * sizeof(u32), 0);
+			mali_mmu_release_table_page(phys, pagedir->page_entries_mapped[i]);
+		}
+	}
+	_mali_osk_write_mem_barrier();
+
+	/* Free the page directory page. */
+	mali_mmu_release_table_page(pagedir->page_directory, pagedir->page_directory_mapped);
+
+	_mali_osk_free(pagedir);
+}
+
+
+void mali_mmu_pagedir_update(struct mali_page_directory *pagedir, u32 mali_address,
+			     mali_dma_addr phys_address, u32 size, u32 permission_bits)
+{
+	u32 end_address = mali_address + size;
+	u32 mali_phys = (u32)phys_address;
+
+	/* Map physical pages into MMU page tables */
+	for (; mali_address < end_address; mali_address += MALI_MMU_PAGE_SIZE, mali_phys += MALI_MMU_PAGE_SIZE) {
+		MALI_DEBUG_ASSERT_POINTER(pagedir->page_entries_mapped[MALI_MMU_PDE_ENTRY(mali_address)]);
+		_mali_osk_mem_iowrite32_relaxed(pagedir->page_entries_mapped[MALI_MMU_PDE_ENTRY(mali_address)],
+						MALI_MMU_PTE_ENTRY(mali_address) * sizeof(u32),
+						mali_phys | permission_bits);
+	}
+}
+
+void mali_mmu_pagedir_diag(struct mali_page_directory *pagedir, u32 fault_addr)
+{
+#if defined(DEBUG)
+	u32 pde_index, pte_index;
+	u32 pde, pte;
+
+	pde_index = MALI_MMU_PDE_ENTRY(fault_addr);
+	pte_index = MALI_MMU_PTE_ENTRY(fault_addr);
+
+
+	pde = _mali_osk_mem_ioread32(pagedir->page_directory_mapped,
+				     pde_index * sizeof(u32));
+
+
+	if (pde & MALI_MMU_FLAGS_PRESENT) {
+		u32 pte_addr = MALI_MMU_ENTRY_ADDRESS(pde);
+
+		pte = _mali_osk_mem_ioread32(pagedir->page_entries_mapped[pde_index],
+					     pte_index * sizeof(u32));
+
+		MALI_DEBUG_PRINT(2, ("\tMMU: %08x: Page table present: %08x\n"
+				     "\t\tPTE: %08x, page %08x is %s\n",
+				     fault_addr, pte_addr, pte,
+				     MALI_MMU_ENTRY_ADDRESS(pte),
+				     pte & MALI_MMU_FLAGS_DEFAULT ? "rw" : "not present"));
+	} else {
+		MALI_DEBUG_PRINT(2, ("\tMMU: %08x: Page table not present: %08x\n",
+				     fault_addr, pde));
+	}
+#else
+	MALI_IGNORE(pagedir);
+	MALI_IGNORE(fault_addr);
+#endif
+}
+
+/* For instrumented */
+struct dump_info {
+	u32 buffer_left;
+	u32 register_writes_size;
+	u32 page_table_dump_size;
+	u32 *buffer;
+};
+
+static _mali_osk_errcode_t writereg(u32 where, u32 what, const char *comment, struct dump_info *info)
+{
+	if (NULL != info) {
+		info->register_writes_size += sizeof(u32) * 2; /* two 32-bit words */
+
+		if (NULL != info->buffer) {
+			/* check that we have enough space */
+			if (info->buffer_left < sizeof(u32) * 2) MALI_ERROR(_MALI_OSK_ERR_NOMEM);
+
+			*info->buffer = where;
+			info->buffer++;
+
+			*info->buffer = what;
+			info->buffer++;
+
+			info->buffer_left -= sizeof(u32) * 2;
+		}
+	}
+
+	MALI_SUCCESS;
+}
+
+static _mali_osk_errcode_t mali_mmu_dump_page(mali_io_address page, u32 phys_addr, struct dump_info *info)
+{
+	if (NULL != info) {
+		/* 4096 for the page and 4 bytes for the address */
+		const u32 page_size_in_elements = MALI_MMU_PAGE_SIZE / 4;
+		const u32 page_size_in_bytes = MALI_MMU_PAGE_SIZE;
+		const u32 dump_size_in_bytes = MALI_MMU_PAGE_SIZE + 4;
+
+		info->page_table_dump_size += dump_size_in_bytes;
+
+		if (NULL != info->buffer) {
+			if (info->buffer_left < dump_size_in_bytes) MALI_ERROR(_MALI_OSK_ERR_NOMEM);
+
+			*info->buffer = phys_addr;
+			info->buffer++;
+
+			_mali_osk_memcpy(info->buffer, page, page_size_in_bytes);
+			info->buffer += page_size_in_elements;
+
+			info->buffer_left -= dump_size_in_bytes;
+		}
+	}
+
+	MALI_SUCCESS;
+}
+
+static _mali_osk_errcode_t dump_mmu_page_table(struct mali_page_directory *pagedir, struct dump_info *info)
+{
+	MALI_DEBUG_ASSERT_POINTER(pagedir);
+	MALI_DEBUG_ASSERT_POINTER(info);
+
+	if (NULL != pagedir->page_directory_mapped) {
+		int i;
+
+		MALI_CHECK_NO_ERROR(
+			mali_mmu_dump_page(pagedir->page_directory_mapped, pagedir->page_directory, info)
+		);
+
+		for (i = 0; i < 1024; i++) {
+			if (NULL != pagedir->page_entries_mapped[i]) {
+				MALI_CHECK_NO_ERROR(
+					mali_mmu_dump_page(pagedir->page_entries_mapped[i],
+							   _mali_osk_mem_ioread32(pagedir->page_directory_mapped,
+									   i * sizeof(u32)) & ~MALI_MMU_FLAGS_MASK, info)
+				);
+			}
+		}
+	}
+
+	MALI_SUCCESS;
+}
+
+static _mali_osk_errcode_t dump_mmu_registers(struct mali_page_directory *pagedir, struct dump_info *info)
+{
+	MALI_CHECK_NO_ERROR(writereg(0x00000000, pagedir->page_directory,
+				     "set the page directory address", info));
+	MALI_CHECK_NO_ERROR(writereg(0x00000008, 4, "zap???", info));
+	MALI_CHECK_NO_ERROR(writereg(0x00000008, 0, "enable paging", info));
+	MALI_SUCCESS;
+}
+
+_mali_osk_errcode_t _mali_ukk_query_mmu_page_table_dump_size(_mali_uk_query_mmu_page_table_dump_size_s *args)
+{
+	struct dump_info info = { 0, 0, 0, NULL };
+	struct mali_session_data *session_data;
+
+	session_data = (struct mali_session_data *)(uintptr_t)(args->ctx);
+	MALI_DEBUG_ASSERT_POINTER(session_data);
+	MALI_DEBUG_ASSERT_POINTER(args);
+
+	MALI_CHECK_NO_ERROR(dump_mmu_registers(session_data->page_directory, &info));
+	MALI_CHECK_NO_ERROR(dump_mmu_page_table(session_data->page_directory, &info));
+	args->size = info.register_writes_size + info.page_table_dump_size;
+	MALI_SUCCESS;
+}
+
+_mali_osk_errcode_t _mali_ukk_dump_mmu_page_table(_mali_uk_dump_mmu_page_table_s *args)
+{
+	struct dump_info info = { 0, 0, 0, NULL };
+	struct mali_session_data *session_data;
+
+	MALI_DEBUG_ASSERT_POINTER(args);
+
+	session_data = (struct mali_session_data *)(uintptr_t)(args->ctx);
+	MALI_DEBUG_ASSERT_POINTER(session_data);
+
+	info.buffer_left = args->size;
+	info.buffer = (u32 *)(uintptr_t)args->buffer;
+
+	args->register_writes = (uintptr_t)info.buffer;
+	MALI_CHECK_NO_ERROR(dump_mmu_registers(session_data->page_directory, &info));
+
+	args->page_table_dump = (uintptr_t)info.buffer;
+	MALI_CHECK_NO_ERROR(dump_mmu_page_table(session_data->page_directory, &info));
+
+	args->register_writes_size = info.register_writes_size;
+	args->page_table_dump_size = info.page_table_dump_size;
+
+	MALI_SUCCESS;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_mmu_page_directory.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_mmu_page_directory.h
@@ -0,0 +1,110 @@
+/*
+ * Copyright (C) 2011-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MMU_PAGE_DIRECTORY_H__
+#define __MALI_MMU_PAGE_DIRECTORY_H__
+
+#include "mali_osk.h"
+
+/**
+ * Size of an MMU page in bytes
+ */
+#define MALI_MMU_PAGE_SIZE 0x1000
+
+/*
+ * Size of the address space referenced by a page table page
+ */
+#define MALI_MMU_VIRTUAL_PAGE_SIZE 0x400000 /* 4 MiB */
+
+/**
+ * Page directory index from address
+ * Calculates the page directory index from the given address
+ */
+#define MALI_MMU_PDE_ENTRY(address) (((address)>>22) & 0x03FF)
+
+/**
+ * Page table index from address
+ * Calculates the page table index from the given address
+ */
+#define MALI_MMU_PTE_ENTRY(address) (((address)>>12) & 0x03FF)
+
+/**
+ * Extract the memory address from an PDE/PTE entry
+ */
+#define MALI_MMU_ENTRY_ADDRESS(value) ((value) & 0xFFFFFC00)
+
+#define MALI_INVALID_PAGE ((u32)(~0))
+
+/**
+ *
+ */
+typedef enum mali_mmu_entry_flags {
+	MALI_MMU_FLAGS_PRESENT = 0x01,
+	MALI_MMU_FLAGS_READ_PERMISSION = 0x02,
+	MALI_MMU_FLAGS_WRITE_PERMISSION = 0x04,
+	MALI_MMU_FLAGS_OVERRIDE_CACHE  = 0x8,
+	MALI_MMU_FLAGS_WRITE_CACHEABLE  = 0x10,
+	MALI_MMU_FLAGS_WRITE_ALLOCATE  = 0x20,
+	MALI_MMU_FLAGS_WRITE_BUFFERABLE  = 0x40,
+	MALI_MMU_FLAGS_READ_CACHEABLE  = 0x80,
+	MALI_MMU_FLAGS_READ_ALLOCATE  = 0x100,
+	MALI_MMU_FLAGS_MASK = 0x1FF,
+} mali_mmu_entry_flags;
+
+
+#define MALI_MMU_FLAGS_FORCE_GP_READ_ALLOCATE ( \
+		MALI_MMU_FLAGS_PRESENT | \
+		MALI_MMU_FLAGS_READ_PERMISSION |  \
+		MALI_MMU_FLAGS_WRITE_PERMISSION | \
+		MALI_MMU_FLAGS_OVERRIDE_CACHE | \
+		MALI_MMU_FLAGS_WRITE_CACHEABLE | \
+		MALI_MMU_FLAGS_WRITE_BUFFERABLE | \
+		MALI_MMU_FLAGS_READ_CACHEABLE | \
+		MALI_MMU_FLAGS_READ_ALLOCATE )
+
+#define MALI_MMU_FLAGS_DEFAULT ( \
+				 MALI_MMU_FLAGS_PRESENT | \
+				 MALI_MMU_FLAGS_READ_PERMISSION |  \
+				 MALI_MMU_FLAGS_WRITE_PERMISSION )
+
+
+struct mali_page_directory {
+	u32 page_directory; /**< Physical address of the memory session's page directory */
+	mali_io_address page_directory_mapped; /**< Pointer to the mapped version of the page directory into the kernel's address space */
+
+	mali_io_address page_entries_mapped[1024]; /**< Pointers to the page tables which exists in the page directory mapped into the kernel's address space */
+	u32   page_entries_usage_count[1024]; /**< Tracks usage count of the page table pages, so they can be releases on the last reference */
+};
+
+/* Map Mali virtual address space (i.e. ensure page tables exist for the virtual range)  */
+_mali_osk_errcode_t mali_mmu_pagedir_map(struct mali_page_directory *pagedir, u32 mali_address, u32 size);
+_mali_osk_errcode_t mali_mmu_pagedir_unmap(struct mali_page_directory *pagedir, u32 mali_address, u32 size);
+
+/* Back virtual address space with actual pages. Assumes input is contiguous and 4k aligned. */
+void mali_mmu_pagedir_update(struct mali_page_directory *pagedir, u32 mali_address,
+			     mali_dma_addr phys_address, u32 size, u32 permission_bits);
+
+u32 mali_allocate_empty_page(mali_io_address *virtual);
+void mali_free_empty_page(mali_dma_addr address, mali_io_address virt_addr);
+_mali_osk_errcode_t mali_create_fault_flush_pages(mali_dma_addr *page_directory,
+		mali_io_address *page_directory_mapping,
+		mali_dma_addr *page_table, mali_io_address *page_table_mapping,
+		mali_dma_addr *data_page, mali_io_address *data_page_mapping);
+void mali_destroy_fault_flush_pages(
+	mali_dma_addr *page_directory, mali_io_address *page_directory_mapping,
+	mali_dma_addr *page_table, mali_io_address *page_table_mapping,
+	mali_dma_addr *data_page, mali_io_address *data_page_mapping);
+
+struct mali_page_directory *mali_mmu_pagedir_alloc(void);
+void mali_mmu_pagedir_free(struct mali_page_directory *pagedir);
+
+void mali_mmu_pagedir_diag(struct mali_page_directory *pagedir, u32 fault_addr);
+
+#endif /* __MALI_MMU_PAGE_DIRECTORY_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_osk.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_osk.h
@@ -0,0 +1,1402 @@
+/*
+ * Copyright (C) 2010-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk.h
+ * Defines the OS abstraction layer for the kernel device driver (OSK)
+ */
+
+#ifndef __MALI_OSK_H__
+#define __MALI_OSK_H__
+
+#include <linux/seq_file.h>
+#include "mali_osk_types.h"
+#include "mali_osk_specific.h"           /* include any per-os specifics */
+#include "mali_osk_locks.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @addtogroup uddapi Unified Device Driver (UDD) APIs
+ *
+ * @{
+ */
+
+/**
+ * @addtogroup oskapi UDD OS Abstraction for Kernel-side (OSK) APIs
+ *
+ * @{
+ */
+
+/** @addtogroup _mali_osk_lock OSK Mutual Exclusion Locks
+ * @{ */
+
+#ifdef DEBUG
+/** @brief Macro for asserting that the current thread holds a given lock
+ */
+#define MALI_DEBUG_ASSERT_LOCK_HELD(l) MALI_DEBUG_ASSERT(_mali_osk_lock_get_owner((_mali_osk_lock_debug_t *)l) == _mali_osk_get_tid());
+
+/** @brief returns a lock's owner (thread id) if debugging is enabled
+ */
+#else
+#define MALI_DEBUG_ASSERT_LOCK_HELD(l) do {} while(0)
+#endif
+
+#define _mali_osk_ctxprintf     seq_printf
+
+/** @} */ /* end group _mali_osk_lock */
+
+/** @addtogroup _mali_osk_miscellaneous
+ * @{ */
+
+/** @brief Find the containing structure of another structure
+ *
+ * This is the reverse of the operation 'offsetof'. This means that the
+ * following condition is satisfied:
+ *
+ *   ptr == _MALI_OSK_CONTAINER_OF( &ptr->member, type, member )
+ *
+ * When ptr is of type 'type'.
+ *
+ * Its purpose it to recover a larger structure that has wrapped a smaller one.
+ *
+ * @note no type or memory checking occurs to ensure that a wrapper structure
+ * does in fact exist, and that it is being recovered with respect to the
+ * correct member.
+ *
+ * @param ptr the pointer to the member that is contained within the larger
+ * structure
+ * @param type the type of the structure that contains the member
+ * @param member the name of the member in the structure that ptr points to.
+ * @return a pointer to a \a type object which contains \a member, as pointed
+ * to by \a ptr.
+ */
+#define _MALI_OSK_CONTAINER_OF(ptr, type, member) \
+	((type *)( ((char *)ptr) - offsetof(type,member) ))
+
+/** @addtogroup _mali_osk_wq
+ * @{ */
+
+/** @brief Initialize work queues (for deferred work)
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_wq_init(void);
+
+/** @brief Terminate work queues (for deferred work)
+ */
+void _mali_osk_wq_term(void);
+
+/** @brief Create work in the work queue
+ *
+ * Creates a work object which can be scheduled in the work queue. When
+ * scheduled, \a handler will be called with \a data as the argument.
+ *
+ * Refer to \ref _mali_osk_wq_schedule_work() for details on how work
+ * is scheduled in the queue.
+ *
+ * The returned pointer must be freed with \ref _mali_osk_wq_delete_work()
+ * when no longer needed.
+ */
+_mali_osk_wq_work_t *_mali_osk_wq_create_work(_mali_osk_wq_work_handler_t handler, void *data);
+
+/** @brief A high priority version of \a _mali_osk_wq_create_work()
+ *
+ * Creates a work object which can be scheduled in the high priority work queue.
+ *
+ * This is unfortunately needed to get low latency scheduling of the Mali cores.  Normally we would
+ * schedule the next job in hw_irq or tasklet, but often we can't since we need to synchronously map
+ * and unmap shared memory when a job is connected to external fences (timelines). And this requires
+ * taking a mutex.
+ *
+ * We do signal a lot of other (low priority) work also as part of the job being finished, and if we
+ * don't set this Mali scheduling thread as high priority, we see that the CPU scheduler often runs
+ * random things instead of starting the next GPU job when the GPU is idle.  So setting the gpu
+ * scheduler to high priority does give a visually more responsive system.
+ *
+ * Start the high priority work with: \a _mali_osk_wq_schedule_work_high_pri()
+ */
+_mali_osk_wq_work_t *_mali_osk_wq_create_work_high_pri(_mali_osk_wq_work_handler_t handler, void *data);
+
+/** @brief Delete a work object
+ *
+ * This will flush the work queue to ensure that the work handler will not
+ * be called after deletion.
+ */
+void _mali_osk_wq_delete_work(_mali_osk_wq_work_t *work);
+
+/** @brief Delete a work object
+ *
+ * This will NOT flush the work queue, so only call this if you are sure that the work handler will
+ * not be called after deletion.
+ */
+void _mali_osk_wq_delete_work_nonflush(_mali_osk_wq_work_t *work);
+
+/** @brief Cause a queued, deferred call of the work handler
+ *
+ * _mali_osk_wq_schedule_work provides a mechanism for enqueuing deferred calls
+ * to the work handler. After calling \ref _mali_osk_wq_schedule_work(), the
+ * work handler will be scheduled to run at some point in the future.
+ *
+ * Typically this is called by the IRQ upper-half to defer further processing of
+ * IRQ-related work to the IRQ bottom-half handler. This is necessary for work
+ * that cannot be done in an IRQ context by the IRQ upper-half handler. Timer
+ * callbacks also use this mechanism, because they are treated as though they
+ * operate in an IRQ context. Refer to \ref _mali_osk_timer_t for more
+ * information.
+ *
+ * Code that operates in a kernel-process context (with no IRQ context
+ * restrictions) may also enqueue deferred calls to the IRQ bottom-half. The
+ * advantage over direct calling is that deferred calling allows the caller and
+ * IRQ bottom half to hold the same mutex, with a guarantee that they will not
+ * deadlock just by using this mechanism.
+ *
+ * _mali_osk_wq_schedule_work() places deferred call requests on a queue, to
+ * allow for more than one thread to make a deferred call. Therfore, if it is
+ * called 'K' times, then the IRQ bottom-half will be scheduled 'K' times too.
+ * 'K' is a number that is implementation-specific.
+ *
+ * _mali_osk_wq_schedule_work() is guaranteed to not block on:
+ * - enqueuing a deferred call request.
+ * - the completion of the work handler.
+ *
+ * This is to prevent deadlock. For example, if _mali_osk_wq_schedule_work()
+ * blocked, then it would cause a deadlock when the following two conditions
+ * hold:
+ * - The work handler callback (of type _mali_osk_wq_work_handler_t) locks
+ * a mutex
+ * - And, at the same time, the caller of _mali_osk_wq_schedule_work() also
+ * holds the same mutex
+ *
+ * @note care must be taken to not overflow the queue that
+ * _mali_osk_wq_schedule_work() operates on. Code must be structured to
+ * ensure that the number of requests made to the queue is bounded. Otherwise,
+ * work will be lost.
+ *
+ * The queue that _mali_osk_wq_schedule_work implements is a FIFO of N-writer,
+ * 1-reader type. The writers are the callers of _mali_osk_wq_schedule_work
+ * (all OSK-registered IRQ upper-half handlers in the system, watchdog timers,
+ * callers from a Kernel-process context). The reader is a single thread that
+ * handles all OSK-registered work.
+ *
+ * @param work a pointer to the _mali_osk_wq_work_t object corresponding to the
+ * work to begin processing.
+ */
+void _mali_osk_wq_schedule_work(_mali_osk_wq_work_t *work);
+
+/** @brief Cause a queued, deferred call of the high priority work handler
+ *
+ * Function is the same as \a _mali_osk_wq_schedule_work() with the only
+ * difference that it runs in a high (real time) priority on the system.
+ *
+ * Should only be used as a substitue for doing the same work in interrupts.
+ *
+ * This is allowed to sleep, but the work should be small since it will block
+ * all other applications.
+*/
+void _mali_osk_wq_schedule_work_high_pri(_mali_osk_wq_work_t *work);
+
+/** @brief Flush the work queue
+ *
+ * This will flush the OSK work queue, ensuring all work in the queue has
+ * completed before returning.
+ *
+ * Since this blocks on the completion of work in the work-queue, the
+ * caller of this function \b must \b not hold any mutexes that are taken by
+ * any registered work handler. To do so may cause a deadlock.
+ *
+ */
+void _mali_osk_wq_flush(void);
+
+/** @brief Create work in the delayed work queue
+ *
+ * Creates a work object which can be scheduled in the work queue. When
+ * scheduled, a timer will be start and the \a handler will be called with
+ * \a data as the argument when timer out
+ *
+ * Refer to \ref _mali_osk_wq_delayed_schedule_work() for details on how work
+ * is scheduled in the queue.
+ *
+ * The returned pointer must be freed with \ref _mali_osk_wq_delayed_delete_work_nonflush()
+ * when no longer needed.
+ */
+_mali_osk_wq_delayed_work_t *_mali_osk_wq_delayed_create_work(_mali_osk_wq_work_handler_t handler, void *data);
+
+/** @brief Delete a work object
+ *
+ * This will NOT flush the work queue, so only call this if you are sure that the work handler will
+ * not be called after deletion.
+ */
+void _mali_osk_wq_delayed_delete_work_nonflush(_mali_osk_wq_delayed_work_t *work);
+
+/** @brief Cancel a delayed work without waiting for it to finish
+ *
+ * Note that the \a work callback function may still be running on return from
+ * _mali_osk_wq_delayed_cancel_work_async().
+ *
+ * @param work The delayed work to be cancelled
+ */
+void _mali_osk_wq_delayed_cancel_work_async(_mali_osk_wq_delayed_work_t *work);
+
+/** @brief Cancel a delayed work and wait for it to finish
+ *
+ * When this function returns, the \a work was either cancelled or it finished running.
+ *
+ * @param work The delayed work to be cancelled
+ */
+void _mali_osk_wq_delayed_cancel_work_sync(_mali_osk_wq_delayed_work_t *work);
+
+/** @brief Put \a work task in global workqueue after delay
+ *
+ * After waiting for a given time this puts a job in the kernel-global
+ * workqueue.
+ *
+ * If \a work was already on a queue, this function will return without doing anything
+ *
+ * @param work job to be done
+ * @param delay number of jiffies to wait or 0 for immediate execution
+ */
+void _mali_osk_wq_delayed_schedule_work(_mali_osk_wq_delayed_work_t *work, u32 delay);
+
+/** @} */ /* end group _mali_osk_wq */
+
+
+/** @addtogroup _mali_osk_irq
+ * @{ */
+
+/** @brief Initialize IRQ handling for a resource
+ *
+ * Registers an interrupt handler \a uhandler for the given IRQ number \a irqnum.
+ * \a data will be passed as argument to the handler when an interrupt occurs.
+ *
+ * If \a irqnum is -1, _mali_osk_irq_init will probe for the IRQ number using
+ * the supplied \a trigger_func and \a ack_func. These functions will also
+ * receive \a data as their argument.
+ *
+ * @param irqnum The IRQ number that the resource uses, as seen by the CPU.
+ * The value -1 has a special meaning which indicates the use of probing, and
+ * trigger_func and ack_func must be non-NULL.
+ * @param uhandler The interrupt handler, corresponding to a ISR handler for
+ * the resource
+ * @param int_data resource specific data, which will be passed to uhandler
+ * @param trigger_func Optional: a function to trigger the resource's irq, to
+ * probe for the interrupt. Use NULL if irqnum != -1.
+ * @param ack_func Optional: a function to acknowledge the resource's irq, to
+ * probe for the interrupt. Use NULL if irqnum != -1.
+ * @param probe_data resource-specific data, which will be passed to
+ * (if present) trigger_func and ack_func
+ * @param description textual description of the IRQ resource.
+ * @return on success, a pointer to a _mali_osk_irq_t object, which represents
+ * the IRQ handling on this resource. NULL on failure.
+ */
+_mali_osk_irq_t *_mali_osk_irq_init(u32 irqnum, _mali_osk_irq_uhandler_t uhandler, void *int_data, _mali_osk_irq_trigger_t trigger_func, _mali_osk_irq_ack_t ack_func, void *probe_data, const char *description);
+
+/** @brief Terminate IRQ handling on a resource.
+ *
+ * This will disable the interrupt from the device, and then waits for any
+ * currently executing IRQ handlers to complete.
+ *
+ * @note If work is deferred to an IRQ bottom-half handler through
+ * \ref _mali_osk_wq_schedule_work(), be sure to flush any remaining work
+ * with \ref _mali_osk_wq_flush() or (implicitly) with \ref _mali_osk_wq_delete_work()
+ *
+ * @param irq a pointer to the _mali_osk_irq_t object corresponding to the
+ * resource whose IRQ handling is to be terminated.
+ */
+void _mali_osk_irq_term(_mali_osk_irq_t *irq);
+
+/** @} */ /* end group _mali_osk_irq */
+
+
+/** @addtogroup _mali_osk_atomic
+ * @{ */
+
+/** @brief Decrement an atomic counter
+ *
+ * @note It is an error to decrement the counter beyond -(1<<23)
+ *
+ * @param atom pointer to an atomic counter */
+void _mali_osk_atomic_dec(_mali_osk_atomic_t *atom);
+
+/** @brief Decrement an atomic counter, return new value
+ *
+ * @param atom pointer to an atomic counter
+ * @return The new value, after decrement */
+u32 _mali_osk_atomic_dec_return(_mali_osk_atomic_t *atom);
+
+/** @brief Increment an atomic counter
+ *
+ * @note It is an error to increment the counter beyond (1<<23)-1
+ *
+ * @param atom pointer to an atomic counter */
+void _mali_osk_atomic_inc(_mali_osk_atomic_t *atom);
+
+/** @brief Increment an atomic counter, return new value
+ *
+ * @param atom pointer to an atomic counter */
+u32 _mali_osk_atomic_inc_return(_mali_osk_atomic_t *atom);
+
+/** @brief Initialize an atomic counter
+ *
+ * @note the parameter required is a u32, and so signed integers should be
+ * cast to u32.
+ *
+ * @param atom pointer to an atomic counter
+ * @param val the value to initialize the atomic counter.
+ */
+void _mali_osk_atomic_init(_mali_osk_atomic_t *atom, u32 val);
+
+/** @brief Read a value from an atomic counter
+ *
+ * This can only be safely used to determine the value of the counter when it
+ * is guaranteed that other threads will not be modifying the counter. This
+ * makes its usefulness limited.
+ *
+ * @param atom pointer to an atomic counter
+ */
+u32 _mali_osk_atomic_read(_mali_osk_atomic_t *atom);
+
+/** @brief Terminate an atomic counter
+ *
+ * @param atom pointer to an atomic counter
+ */
+void _mali_osk_atomic_term(_mali_osk_atomic_t *atom);
+
+/** @brief Assign a new val to atomic counter, and return the old atomic counter
+ *
+ * @param atom pointer to an atomic counter
+ * @param val the new value assign to the atomic counter
+ * @return the old value of the atomic counter
+ */
+u32 _mali_osk_atomic_xchg(_mali_osk_atomic_t *atom, u32 val);
+/** @} */  /* end group _mali_osk_atomic */
+
+
+/** @defgroup _mali_osk_memory OSK Memory Allocation
+ * @{ */
+
+/** @brief Allocate zero-initialized memory.
+ *
+ * Returns a buffer capable of containing at least \a n elements of \a size
+ * bytes each. The buffer is initialized to zero.
+ *
+ * If there is a need for a bigger block of memory (16KB or bigger), then
+ * consider to use _mali_osk_vmalloc() instead, as this function might
+ * map down to a OS function with size limitations.
+ *
+ * The buffer is suitably aligned for storage and subsequent access of every
+ * type that the compiler supports. Therefore, the pointer to the start of the
+ * buffer may be cast into any pointer type, and be subsequently accessed from
+ * such a pointer, without loss of information.
+ *
+ * When the buffer is no longer in use, it must be freed with _mali_osk_free().
+ * Failure to do so will cause a memory leak.
+ *
+ * @note Most toolchains supply memory allocation functions that meet the
+ * compiler's alignment requirements.
+ *
+ * @param n Number of elements to allocate
+ * @param size Size of each element
+ * @return On success, the zero-initialized buffer allocated. NULL on failure
+ */
+void *_mali_osk_calloc(u32 n, u32 size);
+
+/** @brief Allocate memory.
+ *
+ * Returns a buffer capable of containing at least \a size bytes. The
+ * contents of the buffer are undefined.
+ *
+ * If there is a need for a bigger block of memory (16KB or bigger), then
+ * consider to use _mali_osk_vmalloc() instead, as this function might
+ * map down to a OS function with size limitations.
+ *
+ * The buffer is suitably aligned for storage and subsequent access of every
+ * type that the compiler supports. Therefore, the pointer to the start of the
+ * buffer may be cast into any pointer type, and be subsequently accessed from
+ * such a pointer, without loss of information.
+ *
+ * When the buffer is no longer in use, it must be freed with _mali_osk_free().
+ * Failure to do so will cause a memory leak.
+ *
+ * @note Most toolchains supply memory allocation functions that meet the
+ * compiler's alignment requirements.
+ *
+ * Remember to free memory using _mali_osk_free().
+ * @param size Number of bytes to allocate
+ * @return On success, the buffer allocated. NULL on failure.
+ */
+void *_mali_osk_malloc(u32 size);
+
+/** @brief Free memory.
+ *
+ * Reclaims the buffer pointed to by the parameter \a ptr for the system.
+ * All memory returned from _mali_osk_malloc() and _mali_osk_calloc()
+ * must be freed before the application exits. Otherwise,
+ * a memory leak will occur.
+ *
+ * Memory must be freed once. It is an error to free the same non-NULL pointer
+ * more than once.
+ *
+ * It is legal to free the NULL pointer.
+ *
+ * @param ptr Pointer to buffer to free
+ */
+void _mali_osk_free(void *ptr);
+
+/** @brief Allocate memory.
+ *
+ * Returns a buffer capable of containing at least \a size bytes. The
+ * contents of the buffer are undefined.
+ *
+ * This function is potentially slower than _mali_osk_malloc() and _mali_osk_calloc(),
+ * but do support bigger sizes.
+ *
+ * The buffer is suitably aligned for storage and subsequent access of every
+ * type that the compiler supports. Therefore, the pointer to the start of the
+ * buffer may be cast into any pointer type, and be subsequently accessed from
+ * such a pointer, without loss of information.
+ *
+ * When the buffer is no longer in use, it must be freed with _mali_osk_free().
+ * Failure to do so will cause a memory leak.
+ *
+ * @note Most toolchains supply memory allocation functions that meet the
+ * compiler's alignment requirements.
+ *
+ * Remember to free memory using _mali_osk_free().
+ * @param size Number of bytes to allocate
+ * @return On success, the buffer allocated. NULL on failure.
+ */
+void *_mali_osk_valloc(u32 size);
+
+/** @brief Free memory.
+ *
+ * Reclaims the buffer pointed to by the parameter \a ptr for the system.
+ * All memory returned from _mali_osk_valloc() must be freed before the
+ * application exits. Otherwise a memory leak will occur.
+ *
+ * Memory must be freed once. It is an error to free the same non-NULL pointer
+ * more than once.
+ *
+ * It is legal to free the NULL pointer.
+ *
+ * @param ptr Pointer to buffer to free
+ */
+void _mali_osk_vfree(void *ptr);
+
+/** @brief Copies memory.
+ *
+ * Copies the \a len bytes from the buffer pointed by the parameter \a src
+ * directly to the buffer pointed by \a dst.
+ *
+ * It is an error for \a src to overlap \a dst anywhere in \a len bytes.
+ *
+ * @param dst Pointer to the destination array where the content is to be
+ * copied.
+ * @param src Pointer to the source of data to be copied.
+ * @param len Number of bytes to copy.
+ * @return \a dst is always passed through unmodified.
+ */
+void *_mali_osk_memcpy(void *dst, const void *src, u32 len);
+
+/** @brief Fills memory.
+ *
+ * Sets the first \a n bytes of the block of memory pointed to by \a s to
+ * the specified value
+ * @param s Pointer to the block of memory to fill.
+ * @param c Value to be set, passed as u32. Only the 8 Least Significant Bits (LSB)
+ * are used.
+ * @param n Number of bytes to be set to the value.
+ * @return \a s is always passed through unmodified
+ */
+void *_mali_osk_memset(void *s, u32 c, u32 n);
+/** @} */ /* end group _mali_osk_memory */
+
+
+/** @brief Checks the amount of memory allocated
+ *
+ * Checks that not more than \a max_allocated bytes are allocated.
+ *
+ * Some OS bring up an interactive out of memory dialogue when the
+ * system runs out of memory. This can stall non-interactive
+ * apps (e.g. automated test runs). This function can be used to
+ * not trigger the OOM dialogue by keeping allocations
+ * within a certain limit.
+ *
+ * @return MALI_TRUE when \a max_allocated bytes are not in use yet. MALI_FALSE
+ * when at least \a max_allocated bytes are in use.
+ */
+mali_bool _mali_osk_mem_check_allocated(u32 max_allocated);
+
+
+/** @addtogroup _mali_osk_low_level_memory
+ * @{ */
+
+/** @brief Issue a memory barrier
+ *
+ * This defines an arbitrary memory barrier operation, which forces an ordering constraint
+ * on memory read and write operations.
+ */
+void _mali_osk_mem_barrier(void);
+
+/** @brief Issue a write memory barrier
+ *
+ * This defines an write memory barrier operation which forces an ordering constraint
+ * on memory write operations.
+ */
+void _mali_osk_write_mem_barrier(void);
+
+/** @brief Map a physically contiguous region into kernel space
+ *
+ * This is primarily used for mapping in registers from resources, and Mali-MMU
+ * page tables. The mapping is only visable from kernel-space.
+ *
+ * Access has to go through _mali_osk_mem_ioread32 and _mali_osk_mem_iowrite32
+ *
+ * @param phys CPU-physical base address of the memory to map in. This must
+ * be aligned to the system's page size, which is assumed to be 4K.
+ * @param size the number of bytes of physically contiguous address space to
+ * map in
+ * @param description A textual description of the memory being mapped in.
+ * @return On success, a Mali IO address through which the mapped-in
+ * memory/registers can be accessed. NULL on failure.
+ */
+mali_io_address _mali_osk_mem_mapioregion(uintptr_t phys, u32 size, const char *description);
+
+/** @brief Unmap a physically contiguous address range from kernel space.
+ *
+ * The address range should be one previously mapped in through
+ * _mali_osk_mem_mapioregion.
+ *
+ * It is a programming error to do (but not limited to) the following:
+ * - attempt an unmap twice
+ * - unmap only part of a range obtained through _mali_osk_mem_mapioregion
+ * - unmap more than the range obtained through  _mali_osk_mem_mapioregion
+ * - unmap an address range that was not successfully mapped using
+ * _mali_osk_mem_mapioregion
+ * - provide a mapping that does not map to phys.
+ *
+ * @param phys CPU-physical base address of the memory that was originally
+ * mapped in. This must be aligned to the system's page size, which is assumed
+ * to be 4K
+ * @param size The number of bytes that were originally mapped in.
+ * @param mapping The Mali IO address through which the mapping is
+ * accessed.
+ */
+void _mali_osk_mem_unmapioregion(uintptr_t phys, u32 size, mali_io_address mapping);
+
+/** @brief Allocate and Map a physically contiguous region into kernel space
+ *
+ * This is used for allocating physically contiguous regions (such as Mali-MMU
+ * page tables) and mapping them into kernel space. The mapping is only
+ * visible from kernel-space.
+ *
+ * The alignment of the returned memory is guaranteed to be at least
+ * _MALI_OSK_CPU_PAGE_SIZE.
+ *
+ * Access must go through _mali_osk_mem_ioread32 and _mali_osk_mem_iowrite32
+ *
+ * @note This function is primarily to provide support for OSs that are
+ * incapable of separating the tasks 'allocate physically contiguous memory'
+ * and 'map it into kernel space'
+ *
+ * @param[out] phys CPU-physical base address of memory that was allocated.
+ * (*phys) will be guaranteed to be aligned to at least
+ * _MALI_OSK_CPU_PAGE_SIZE on success.
+ *
+ * @param[in] size the number of bytes of physically contiguous memory to
+ * allocate. This must be a multiple of _MALI_OSK_CPU_PAGE_SIZE.
+ *
+ * @return On success, a Mali IO address through which the mapped-in
+ * memory/registers can be accessed. NULL on failure, and (*phys) is unmodified.
+ */
+mali_io_address _mali_osk_mem_allocioregion(u32 *phys, u32 size);
+
+/** @brief Free a physically contiguous address range from kernel space.
+ *
+ * The address range should be one previously mapped in through
+ * _mali_osk_mem_allocioregion.
+ *
+ * It is a programming error to do (but not limited to) the following:
+ * - attempt a free twice on the same ioregion
+ * - free only part of a range obtained through _mali_osk_mem_allocioregion
+ * - free more than the range obtained through  _mali_osk_mem_allocioregion
+ * - free an address range that was not successfully mapped using
+ * _mali_osk_mem_allocioregion
+ * - provide a mapping that does not map to phys.
+ *
+ * @param phys CPU-physical base address of the memory that was originally
+ * mapped in, which was aligned to _MALI_OSK_CPU_PAGE_SIZE.
+ * @param size The number of bytes that were originally mapped in, which was
+ * a multiple of _MALI_OSK_CPU_PAGE_SIZE.
+ * @param mapping The Mali IO address through which the mapping is
+ * accessed.
+ */
+void _mali_osk_mem_freeioregion(u32 phys, u32 size, mali_io_address mapping);
+
+/** @brief Request a region of physically contiguous memory
+ *
+ * This is used to ensure exclusive access to a region of physically contigous
+ * memory.
+ *
+ * It is acceptable to implement this as a stub. However, it is then the job
+ * of the System Integrator to ensure that no other device driver will be using
+ * the physical address ranges used by Mali, while the Mali device driver is
+ * loaded.
+ *
+ * @param phys CPU-physical base address of the memory to request. This must
+ * be aligned to the system's page size, which is assumed to be 4K.
+ * @param size the number of bytes of physically contiguous address space to
+ * request.
+ * @param description A textual description of the memory being requested.
+ * @return _MALI_OSK_ERR_OK on success. Otherwise, a suitable
+ * _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_osk_mem_reqregion(uintptr_t phys, u32 size, const char *description);
+
+/** @brief Un-request a region of physically contiguous memory
+ *
+ * This is used to release a regious of physically contiguous memory previously
+ * requested through _mali_osk_mem_reqregion, so that other device drivers may
+ * use it. This will be called at time of Mali device driver termination.
+ *
+ * It is a programming error to attempt to:
+ * - unrequest a region twice
+ * - unrequest only part of a range obtained through _mali_osk_mem_reqregion
+ * - unrequest more than the range obtained through  _mali_osk_mem_reqregion
+ * - unrequest an address range that was not successfully requested using
+ * _mali_osk_mem_reqregion
+ *
+ * @param phys CPU-physical base address of the memory to un-request. This must
+ * be aligned to the system's page size, which is assumed to be 4K
+ * @param size the number of bytes of physically contiguous address space to
+ * un-request.
+ */
+void _mali_osk_mem_unreqregion(uintptr_t phys, u32 size);
+
+/** @brief Read from a location currently mapped in through
+ * _mali_osk_mem_mapioregion
+ *
+ * This reads a 32-bit word from a 32-bit aligned location. It is a programming
+ * error to provide unaligned locations, or to read from memory that is not
+ * mapped in, or not mapped through either _mali_osk_mem_mapioregion() or
+ * _mali_osk_mem_allocioregion().
+ *
+ * @param mapping Mali IO address to read from
+ * @param offset Byte offset from the given IO address to operate on, must be a multiple of 4
+ * @return the 32-bit word from the specified location.
+ */
+u32 _mali_osk_mem_ioread32(volatile mali_io_address mapping, u32 offset);
+
+/** @brief Write to a location currently mapped in through
+ * _mali_osk_mem_mapioregion without memory barriers
+ *
+ * This write a 32-bit word to a 32-bit aligned location without using memory barrier.
+ * It is a programming error to provide unaligned locations, or to write to memory that is not
+ * mapped in, or not mapped through either _mali_osk_mem_mapioregion() or
+ * _mali_osk_mem_allocioregion().
+ *
+ * @param mapping Mali IO address to write to
+ * @param offset Byte offset from the given IO address to operate on, must be a multiple of 4
+ * @param val the 32-bit word to write.
+ */
+void _mali_osk_mem_iowrite32_relaxed(volatile mali_io_address addr, u32 offset, u32 val);
+
+/** @brief Write to a location currently mapped in through
+ * _mali_osk_mem_mapioregion with write memory barrier
+ *
+ * This write a 32-bit word to a 32-bit aligned location. It is a programming
+ * error to provide unaligned locations, or to write to memory that is not
+ * mapped in, or not mapped through either _mali_osk_mem_mapioregion() or
+ * _mali_osk_mem_allocioregion().
+ *
+ * @param mapping Mali IO address to write to
+ * @param offset Byte offset from the given IO address to operate on, must be a multiple of 4
+ * @param val the 32-bit word to write.
+ */
+void _mali_osk_mem_iowrite32(volatile mali_io_address mapping, u32 offset, u32 val);
+
+/** @brief Flush all CPU caches
+ *
+ * This should only be implemented if flushing of the cache is required for
+ * memory mapped in through _mali_osk_mem_mapregion.
+ */
+void _mali_osk_cache_flushall(void);
+
+/** @brief Flush any caches necessary for the CPU and MALI to have the same view of a range of uncached mapped memory
+ *
+ * This should only be implemented if your OS doesn't do a full cache flush (inner & outer)
+ * after allocating uncached mapped memory.
+ *
+ * Some OS do not perform a full cache flush (including all outer caches) for uncached mapped memory.
+ * They zero the memory through a cached mapping, then flush the inner caches but not the outer caches.
+ * This is required for MALI to have the correct view of the memory.
+ */
+void _mali_osk_cache_ensure_uncached_range_flushed(void *uncached_mapping, u32 offset, u32 size);
+
+/** @brief Safely copy as much data as possible from src to dest
+ *
+ * Do not crash if src or dest isn't available.
+ *
+ * @param dest Destination buffer (limited to user space mapped Mali memory)
+ * @param src Source buffer
+ * @param size Number of bytes to copy
+ * @return Number of bytes actually copied
+ */
+u32 _mali_osk_mem_write_safe(void *dest, const void *src, u32 size);
+
+/** @} */ /* end group _mali_osk_low_level_memory */
+
+
+/** @addtogroup _mali_osk_notification
+ *
+ * User space notification framework
+ *
+ * Communication with user space of asynchronous events is performed through a
+ * synchronous call to the \ref u_k_api.
+ *
+ * Since the events are asynchronous, the events have to be queued until a
+ * synchronous U/K API call can be made by user-space. A U/K API call might also
+ * be received before any event has happened. Therefore the notifications the
+ * different subsystems wants to send to user space has to be queued for later
+ * reception, or a U/K API call has to be blocked until an event has occured.
+ *
+ * Typical uses of notifications are after running of jobs on the hardware or
+ * when changes to the system is detected that needs to be relayed to user
+ * space.
+ *
+ * After an event has occured user space has to be notified using some kind of
+ * message. The notification framework supports sending messages to waiting
+ * threads or queueing of messages until a U/K API call is made.
+ *
+ * The notification queue is a FIFO. There are no restrictions on the numbers
+ * of readers or writers in the queue.
+ *
+ * A message contains what user space needs to identifiy how to handle an
+ * event. This includes a type field and a possible type specific payload.
+ *
+ * A notification to user space is represented by a
+ * \ref _mali_osk_notification_t object. A sender gets hold of such an object
+ * using _mali_osk_notification_create(). The buffer given by the
+ * _mali_osk_notification_t::result_buffer field in the object is used to store
+ * any type specific data. The other fields are internal to the queue system
+ * and should not be touched.
+ *
+ * @{ */
+
+/** @brief Create a notification object
+ *
+ * Returns a notification object which can be added to the queue of
+ * notifications pending for user space transfer.
+ *
+ * The implementation will initialize all members of the
+ * \ref _mali_osk_notification_t object. In particular, the
+ * _mali_osk_notification_t::result_buffer member will be initialized to point
+ * to \a size bytes of storage, and that storage will be suitably aligned for
+ * storage of any structure. That is, the created buffer meets the same
+ * requirements as _mali_osk_malloc().
+ *
+ * The notification object must be deleted when not in use. Use
+ * _mali_osk_notification_delete() for deleting it.
+ *
+ * @note You \b must \b not call _mali_osk_free() on a \ref _mali_osk_notification_t,
+ * object, or on a _mali_osk_notification_t::result_buffer. You must only use
+ * _mali_osk_notification_delete() to free the resources assocaited with a
+ * \ref _mali_osk_notification_t object.
+ *
+ * @param type The notification type
+ * @param size The size of the type specific buffer to send
+ * @return Pointer to a notification object with a suitable buffer, or NULL on error.
+ */
+_mali_osk_notification_t *_mali_osk_notification_create(u32 type, u32 size);
+
+/** @brief Delete a notification object
+ *
+ * This must be called to reclaim the resources of a notification object. This
+ * includes:
+ * - The _mali_osk_notification_t::result_buffer
+ * - The \ref _mali_osk_notification_t itself.
+ *
+ * A notification object \b must \b not be used after it has been deleted by
+ * _mali_osk_notification_delete().
+ *
+ * In addition, the notification object may not be deleted while it is in a
+ * queue. That is, if it has been placed on a queue with
+ * _mali_osk_notification_queue_send(), then it must not be deleted until
+ * it has been received by a call to _mali_osk_notification_queue_receive().
+ * Otherwise, the queue may be corrupted.
+ *
+ * @param object the notification object to delete.
+ */
+void _mali_osk_notification_delete(_mali_osk_notification_t *object);
+
+/** @brief Create a notification queue
+ *
+ * Creates a notification queue which can be used to queue messages for user
+ * delivery and get queued messages from
+ *
+ * The queue is a FIFO, and has no restrictions on the numbers of readers or
+ * writers.
+ *
+ * When the queue is no longer in use, it must be terminated with
+ * \ref _mali_osk_notification_queue_term(). Failure to do so will result in a
+ * memory leak.
+ *
+ * @return Pointer to a new notification queue or NULL on error.
+ */
+_mali_osk_notification_queue_t *_mali_osk_notification_queue_init(void);
+
+/** @brief Destroy a notification queue
+ *
+ * Destroys a notification queue and frees associated resources from the queue.
+ *
+ * A notification queue \b must \b not be destroyed in the following cases:
+ * - while there are \ref _mali_osk_notification_t objects in the queue.
+ * - while there are writers currently acting upon the queue. That is, while
+ * a thread is currently calling \ref _mali_osk_notification_queue_send() on
+ * the queue, or while a thread may call
+ * \ref _mali_osk_notification_queue_send() on the queue in the future.
+ * - while there are readers currently waiting upon the queue. That is, while
+ * a thread is currently calling \ref _mali_osk_notification_queue_receive() on
+ * the queue, or while a thread may call
+ * \ref _mali_osk_notification_queue_receive() on the queue in the future.
+ *
+ * Therefore, all \ref _mali_osk_notification_t objects must be flushed and
+ * deleted by the code that makes use of the notification queues, since only
+ * they know the structure of the _mali_osk_notification_t::result_buffer
+ * (even if it may only be a flat sturcture).
+ *
+ * @note Since the queue is a FIFO, the code using notification queues may
+ * create its own 'flush' type of notification, to assist in flushing the
+ * queue.
+ *
+ * Once the queue has been destroyed, it must not be used again.
+ *
+ * @param queue The queue to destroy
+ */
+void _mali_osk_notification_queue_term(_mali_osk_notification_queue_t *queue);
+
+/** @brief Schedule notification for delivery
+ *
+ * When a \ref _mali_osk_notification_t object has been created successfully
+ * and set up, it may be added to the queue of objects waiting for user space
+ * transfer.
+ *
+ * The sending will not block if the queue is full.
+ *
+ * A \ref _mali_osk_notification_t object \b must \b not be put on two different
+ * queues at the same time, or enqueued twice onto a single queue before
+ * reception. However, it is acceptable for it to be requeued \em after reception
+ * from a call to _mali_osk_notification_queue_receive(), even onto the same queue.
+ *
+ * Again, requeuing must also not enqueue onto two different queues at the same
+ * time, or enqueue onto the same queue twice before reception.
+ *
+ * @param queue The notification queue to add this notification to
+ * @param object The entry to add
+ */
+void _mali_osk_notification_queue_send(_mali_osk_notification_queue_t *queue, _mali_osk_notification_t *object);
+
+/** @brief Receive a notification from a queue
+ *
+ * Receives a single notification from the given queue.
+ *
+ * If no notifciations are ready the thread will sleep until one becomes ready.
+ * Therefore, notifications may not be received into an
+ * IRQ or 'atomic' context (that is, a context where sleeping is disallowed).
+ *
+ * @param queue The queue to receive from
+ * @param result Pointer to storage of a pointer of type
+ * \ref _mali_osk_notification_t*. \a result will be written to such that the
+ * expression \a (*result) will evaluate to a pointer to a valid
+ * \ref _mali_osk_notification_t object, or NULL if none were received.
+ * @return _MALI_OSK_ERR_OK on success. _MALI_OSK_ERR_RESTARTSYSCALL if the sleep was interrupted.
+ */
+_mali_osk_errcode_t _mali_osk_notification_queue_receive(_mali_osk_notification_queue_t *queue, _mali_osk_notification_t **result);
+
+/** @brief Dequeues a notification from a queue
+ *
+ * Receives a single notification from the given queue.
+ *
+ * If no notifciations are ready the function call will return an error code.
+ *
+ * @param queue The queue to receive from
+ * @param result Pointer to storage of a pointer of type
+ * \ref _mali_osk_notification_t*. \a result will be written to such that the
+ * expression \a (*result) will evaluate to a pointer to a valid
+ * \ref _mali_osk_notification_t object, or NULL if none were received.
+ * @return _MALI_OSK_ERR_OK on success, _MALI_OSK_ERR_ITEM_NOT_FOUND if queue was empty.
+ */
+_mali_osk_errcode_t _mali_osk_notification_queue_dequeue(_mali_osk_notification_queue_t *queue, _mali_osk_notification_t **result);
+
+/** @} */ /* end group _mali_osk_notification */
+
+
+/** @addtogroup _mali_osk_timer
+ *
+ * Timers use the OS's representation of time, which are 'ticks'. This is to
+ * prevent aliasing problems between the internal timer time, and the time
+ * asked for.
+ *
+ * @{ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+/** @brief Initialize a timer
+ *
+ * Allocates resources for a new timer, and initializes them. This does not
+ * start the timer.
+ *
+ * @param callback Function to call when timer expires
+ * @return a pointer to the allocated timer object, or NULL on failure.
+ */
+_mali_osk_timer_t *_mali_osk_timer_init(_mali_osk_timer_callback_t callback);
+#else
+/** @brief Initialize a timer
+ *
+ * Allocates resources for a new timer, and initializes them. This does not
+ * start the timer.
+ *
+ * @return a pointer to the allocated timer object, or NULL on failure.
+ */
+_mali_osk_timer_t *_mali_osk_timer_init(void);
+#endif
+
+/** @brief Start a timer
+ *
+ * It is an error to start a timer without setting the callback via
+ * _mali_osk_timer_setcallback().
+ *
+ * It is an error to use this to start an already started timer.
+ *
+ * The timer will expire in \a ticks_to_expire ticks, at which point, the
+ * callback function will be invoked with the callback-specific data,
+ * as registered by _mali_osk_timer_setcallback().
+ *
+ * @param tim the timer to start
+ * @param ticks_to_expire the amount of time in ticks for the timer to run
+ * before triggering.
+ */
+void _mali_osk_timer_add(_mali_osk_timer_t *tim, unsigned long ticks_to_expire);
+
+/** @brief Modify a timer
+ *
+ * Set the relative time at which a timer will expire, and start it if it is
+ * stopped. If \a ticks_to_expire 0 the timer fires immediately.
+ *
+ * It is an error to modify a timer without setting the callback via
+ *  _mali_osk_timer_setcallback().
+ *
+ * The timer will expire at \a ticks_to_expire from the time of the call, at
+ * which point, the callback function will be invoked with the
+ * callback-specific data, as set by _mali_osk_timer_setcallback().
+ *
+ * @param tim the timer to modify, and start if necessary
+ * @param ticks_to_expire the \em absolute time in ticks at which this timer
+ * should trigger.
+ *
+ */
+void _mali_osk_timer_mod(_mali_osk_timer_t *tim, unsigned long ticks_to_expire);
+
+/** @brief Stop a timer, and block on its completion.
+ *
+ * Stop the timer. When the function returns, it is guaranteed that the timer's
+ * callback will not be running on any CPU core.
+ *
+ * Since stoping the timer blocks on compeletion of the callback, the callback
+ * may not obtain any mutexes that the caller holds. Otherwise, a deadlock will
+ * occur.
+ *
+ * @note While the callback itself is guaranteed to not be running, work
+ * enqueued on the work-queue by the timer (with
+ * \ref _mali_osk_wq_schedule_work()) may still run. The timer callback and
+ * work handler must take this into account.
+ *
+ * It is legal to stop an already stopped timer.
+ *
+ * @param tim the timer to stop.
+ *
+ */
+void _mali_osk_timer_del(_mali_osk_timer_t *tim);
+
+/** @brief Stop a timer.
+ *
+ * Stop the timer. When the function returns, the timer's callback may still be
+ * running on any CPU core.
+ *
+ * It is legal to stop an already stopped timer.
+ *
+ * @param tim the timer to stop.
+ */
+void _mali_osk_timer_del_async(_mali_osk_timer_t *tim);
+
+/** @brief Check if timer is pending.
+ *
+ * Check if timer is active.
+ *
+ * @param tim the timer to check
+ * @return MALI_TRUE if time is active, MALI_FALSE if it is not active
+ */
+mali_bool _mali_osk_timer_pending(_mali_osk_timer_t *tim);
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 14, 0)
+/** @brief Set a timer's callback parameters.
+ *
+ * This must be called at least once before a timer is started/modified.
+ *
+ * After a timer has been stopped or expires, the callback remains set. This
+ * means that restarting the timer will call the same function with the same
+ * parameters on expiry.
+ *
+ * @param tim the timer to set callback on.
+ * @param callback Function to call when timer expires
+ * @param data Function-specific data to supply to the function on expiry.
+ */
+void _mali_osk_timer_setcallback(_mali_osk_timer_t *tim, _mali_osk_timer_callback_t callback, void *data);
+#endif
+
+/** @brief Terminate a timer, and deallocate resources.
+ *
+ * The timer must first be stopped by calling _mali_osk_timer_del().
+ *
+ * It is a programming error for _mali_osk_timer_term() to be called on:
+ * - timer that is currently running
+ * - a timer that is currently executing its callback.
+ *
+ * @param tim the timer to deallocate.
+ */
+void _mali_osk_timer_term(_mali_osk_timer_t *tim);
+/** @} */ /* end group _mali_osk_timer */
+
+
+/** @defgroup _mali_osk_time OSK Time functions
+ *
+ * \ref _mali_osk_time use the OS's representation of time, which are
+ * 'ticks'. This is to prevent aliasing problems between the internal timer
+ * time, and the time asked for.
+ *
+ * OS tick time is measured as a u32. The time stored in a u32 may either be
+ * an absolute time, or a time delta between two events. Whilst it is valid to
+ * use math opeartors to \em change the tick value represented as a u32, it
+ * is often only meaningful to do such operations on time deltas, rather than
+ * on absolute time. However, it is meaningful to add/subtract time deltas to
+ * absolute times.
+ *
+ * Conversion between tick time and milliseconds (ms) may not be loss-less,
+ * and are \em implementation \em depenedant.
+ *
+ * Code use OS time must take this into account, since:
+ * - a small OS time may (or may not) be rounded
+ * - a large time may (or may not) overflow
+ *
+ * @{ */
+
+/** @brief Return whether ticka occurs after or at the same time as  tickb
+ *
+ * Systems where ticks can wrap must handle that.
+ *
+ * @param ticka ticka
+ * @param tickb tickb
+ * @return MALI_TRUE if ticka represents a time that occurs at or after tickb.
+ */
+mali_bool _mali_osk_time_after_eq(unsigned long ticka, unsigned long tickb);
+
+/** @brief Convert milliseconds to OS 'ticks'
+ *
+ * @param ms time interval in milliseconds
+ * @return the corresponding time interval in OS ticks.
+ */
+unsigned long _mali_osk_time_mstoticks(u32 ms);
+
+/** @brief Convert OS 'ticks' to milliseconds
+ *
+ * @param ticks time interval in OS ticks.
+ * @return the corresponding time interval in milliseconds
+ */
+u32 _mali_osk_time_tickstoms(unsigned long ticks);
+
+
+/** @brief Get the current time in OS 'ticks'.
+ * @return the current time in OS 'ticks'.
+ */
+unsigned long _mali_osk_time_tickcount(void);
+
+/** @brief Cause a microsecond delay
+ *
+ * The delay will have microsecond resolution, and is necessary for correct
+ * operation of the driver. At worst, the delay will be \b at least \a usecs
+ * microseconds, and so may be (significantly) more.
+ *
+ * This function may be implemented as a busy-wait, which is the most sensible
+ * implementation. On OSs where there are situations in which a thread must not
+ * sleep, this is definitely implemented as a busy-wait.
+ *
+ * @param usecs the number of microseconds to wait for.
+ */
+void _mali_osk_time_ubusydelay(u32 usecs);
+
+/** @brief Return time in nano seconds, since any given reference.
+ *
+ * @return Time in nano seconds
+ */
+u64 _mali_osk_time_get_ns(void);
+
+/** @brief Return time in nano seconds, since boot time.
+ *
+ * @return Time in nano seconds
+ */
+u64 _mali_osk_boot_time_get_ns(void);
+
+/** @} */ /* end group _mali_osk_time */
+
+/** @defgroup _mali_osk_math OSK Math
+ * @{ */
+
+/** @brief Count Leading Zeros (Little-endian)
+ *
+ * @note This function must be implemented to support the reference
+ * implementation of _mali_osk_find_first_zero_bit, as defined in
+ * mali_osk_bitops.h.
+ *
+ * @param val 32-bit words to count leading zeros on
+ * @return the number of leading zeros.
+ */
+u32 _mali_osk_clz(u32 val);
+
+/** @brief find last (most-significant) bit set
+ *
+ * @param val 32-bit words to count last bit set on
+ * @return last bit set.
+ */
+u32 _mali_osk_fls(u32 val);
+
+/** @} */ /* end group _mali_osk_math */
+
+/** @addtogroup _mali_osk_wait_queue OSK Wait Queue functionality
+ * @{ */
+
+/** @brief Initialize an empty Wait Queue */
+_mali_osk_wait_queue_t *_mali_osk_wait_queue_init(void);
+
+/** @brief Sleep if condition is false
+ *
+ * @param queue the queue to use
+ * @param condition function pointer to a boolean function
+ * @param data data parameter for condition function
+ *
+ * Put thread to sleep if the given \a condition function returns false. When
+ * being asked to wake up again, the condition will be re-checked and the
+ * thread only woken up if the condition is now true.
+ */
+void _mali_osk_wait_queue_wait_event(_mali_osk_wait_queue_t *queue, mali_bool(*condition)(void *), void *data);
+
+/** @brief Sleep if condition is false
+ *
+ * @param queue the queue to use
+ * @param condition function pointer to a boolean function
+ * @param data data parameter for condition function
+ * @param timeout timeout in ms
+ *
+ * Put thread to sleep if the given \a condition function returns false. When
+ * being asked to wake up again, the condition will be re-checked and the
+ * thread only woken up if the condition is now true.  Will return if time
+ * exceeds timeout.
+ */
+void _mali_osk_wait_queue_wait_event_timeout(_mali_osk_wait_queue_t *queue, mali_bool(*condition)(void *), void *data, u32 timeout);
+
+/** @brief Wake up all threads in wait queue if their respective conditions are
+ * true
+ *
+ * @param queue the queue whose threads should be woken up
+ *
+ * Wake up all threads in wait queue \a queue whose condition is now true.
+ */
+void _mali_osk_wait_queue_wake_up(_mali_osk_wait_queue_t *queue);
+
+/** @brief terminate a wait queue
+ *
+ * @param queue the queue to terminate.
+ */
+void _mali_osk_wait_queue_term(_mali_osk_wait_queue_t *queue);
+/** @} */ /* end group _mali_osk_wait_queue */
+
+
+/** @addtogroup _mali_osk_miscellaneous
+ * @{ */
+
+/** @brief Output a device driver debug message.
+ *
+ * The interpretation of \a fmt is the same as the \c format parameter in
+ * _mali_osu_vsnprintf().
+ *
+ * @param fmt a _mali_osu_vsnprintf() style format string
+ * @param ... a variable-number of parameters suitable for \a fmt
+ */
+void _mali_osk_dbgmsg(const char *fmt, ...);
+
+/** @brief Print fmt into buf.
+ *
+ * The interpretation of \a fmt is the same as the \c format parameter in
+ * _mali_osu_vsnprintf().
+ *
+ * @param buf a pointer to the result buffer
+ * @param size the total number of bytes allowed to write to \a buf
+ * @param fmt a _mali_osu_vsnprintf() style format string
+ * @param ... a variable-number of parameters suitable for \a fmt
+ * @return The number of bytes written to \a buf
+ */
+u32 _mali_osk_snprintf(char *buf, u32 size, const char *fmt, ...);
+
+/** @brief Abnormal process abort.
+ *
+ * Terminates the caller-process if this function is called.
+ *
+ * This function will be called from Debug assert-macros in mali_kernel_common.h.
+ *
+ * This function will never return - because to continue from a Debug assert
+ * could cause even more problems, and hinder debugging of the initial problem.
+ *
+ * This function is only used in Debug builds, and is not used in Release builds.
+ */
+void _mali_osk_abort(void);
+
+/** @brief Sets breakpoint at point where function is called.
+ *
+ * This function will be called from Debug assert-macros in mali_kernel_common.h,
+ * to assist in debugging. If debugging at this level is not required, then this
+ * function may be implemented as a stub.
+ *
+ * This function is only used in Debug builds, and is not used in Release builds.
+ */
+void _mali_osk_break(void);
+
+/** @brief Return an identificator for calling process.
+ *
+ * @return Identificator for calling process.
+ */
+u32 _mali_osk_get_pid(void);
+
+/** @brief Return an name for calling process.
+ *
+ * @return name for calling process.
+ */
+char *_mali_osk_get_comm(void);
+
+/** @brief Return an identificator for calling thread.
+ *
+ * @return Identificator for calling thread.
+ */
+u32 _mali_osk_get_tid(void);
+
+
+/** @brief Take a reference to the power manager system for the Mali device (synchronously).
+ *
+ * When function returns successfully, Mali is ON.
+ *
+ * @note Call \a _mali_osk_pm_dev_ref_put() to release this reference.
+ */
+_mali_osk_errcode_t _mali_osk_pm_dev_ref_get_sync(void);
+
+/** @brief Take a reference to the external power manager system for the Mali device (asynchronously).
+ *
+ * Mali might not yet be on after this function as returned.
+ * Please use \a _mali_osk_pm_dev_barrier() or \a _mali_osk_pm_dev_ref_get_sync()
+ * to wait for Mali to be powered on.
+ *
+ * @note Call \a _mali_osk_pm_dev_ref_dec() to release this reference.
+ */
+_mali_osk_errcode_t _mali_osk_pm_dev_ref_get_async(void);
+
+/** @brief Release the reference to the external power manger system for the Mali device.
+ *
+ * When reference count reach zero, the cores can be off.
+ *
+ * @note This must be used to release references taken with
+ * \a _mali_osk_pm_dev_ref_get_sync() or \a _mali_osk_pm_dev_ref_get_sync().
+ */
+void _mali_osk_pm_dev_ref_put(void);
+
+/** @brief Block until pending PM operations are done
+ */
+void _mali_osk_pm_dev_barrier(void);
+
+/** @} */ /* end group  _mali_osk_miscellaneous */
+
+/** @defgroup _mali_osk_bitmap OSK Bitmap
+ * @{ */
+
+/** @brief Allocate a unique number from the bitmap object.
+ *
+ * @param bitmap Initialized bitmap object.
+ * @return An unique existence in the bitmap object.
+ */
+u32 _mali_osk_bitmap_alloc(struct _mali_osk_bitmap *bitmap);
+
+/** @brief Free a interger to the bitmap object.
+ *
+ * @param bitmap Initialized bitmap object.
+ * @param obj An number allocated from bitmap object.
+ */
+void _mali_osk_bitmap_free(struct _mali_osk_bitmap *bitmap, u32 obj);
+
+/** @brief Allocate continuous number from the bitmap object.
+ *
+ * @param bitmap Initialized bitmap object.
+ * @return start number of the continuous number block.
+ */
+u32 _mali_osk_bitmap_alloc_range(struct _mali_osk_bitmap *bitmap, int cnt);
+
+/** @brief Free a block of continuous number block to the bitmap object.
+ *
+ * @param bitmap Initialized bitmap object.
+ * @param obj Start number.
+ * @param cnt The size of the continuous number block.
+ */
+void _mali_osk_bitmap_free_range(struct _mali_osk_bitmap *bitmap, u32 obj, int cnt);
+
+/** @brief Available count could be used to allocate in the given bitmap object.
+ *
+ */
+u32 _mali_osk_bitmap_avail(struct _mali_osk_bitmap *bitmap);
+
+/** @brief Initialize an bitmap object..
+ *
+ * @param bitmap An poiter of uninitialized bitmap object.
+ * @param num Size of thei bitmap object and decide the memory size allocated.
+ * @param reserve start number used to allocate.
+ */
+int _mali_osk_bitmap_init(struct _mali_osk_bitmap *bitmap, u32 num, u32 reserve);
+
+/** @brief Free the given bitmap object.
+ *
+ * @param bitmap Initialized bitmap object.
+ */
+void _mali_osk_bitmap_term(struct _mali_osk_bitmap *bitmap);
+/** @} */ /* end group  _mali_osk_bitmap */
+
+/** @} */ /* end group osuapi */
+
+/** @} */ /* end group uddapi */
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+/* Check standard inlines */
+#ifndef MALI_STATIC_INLINE
+#error MALI_STATIC_INLINE not defined on your OS
+#endif
+
+#ifndef MALI_NON_STATIC_INLINE
+#error MALI_NON_STATIC_INLINE not defined on your OS
+#endif
+
+#endif /* __MALI_OSK_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_osk_bitops.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_osk_bitops.h
@@ -0,0 +1,162 @@
+/*
+ * Copyright (C) 2010, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_bitops.h
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#ifndef __MALI_OSK_BITOPS_H__
+#define __MALI_OSK_BITOPS_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+MALI_STATIC_INLINE void _mali_internal_clear_bit(u32 bit, u32 *addr)
+{
+	MALI_DEBUG_ASSERT(bit < 32);
+	MALI_DEBUG_ASSERT(NULL != addr);
+
+	(*addr) &= ~(1 << bit);
+}
+
+MALI_STATIC_INLINE void _mali_internal_set_bit(u32 bit, u32 *addr)
+{
+	MALI_DEBUG_ASSERT(bit < 32);
+	MALI_DEBUG_ASSERT(NULL != addr);
+
+	(*addr) |= (1 << bit);
+}
+
+MALI_STATIC_INLINE u32 _mali_internal_test_bit(u32 bit, u32 value)
+{
+	MALI_DEBUG_ASSERT(bit < 32);
+	return value & (1 << bit);
+}
+
+MALI_STATIC_INLINE int _mali_internal_find_first_zero_bit(u32 value)
+{
+	u32 inverted;
+	u32 negated;
+	u32 isolated;
+	u32 leading_zeros;
+
+	/* Begin with xxx...x0yyy...y, where ys are 1, number of ys is in range  0..31 */
+	inverted = ~value; /* zzz...z1000...0 */
+	/* Using count_trailing_zeros on inverted value -
+	 * See ARM System Developers Guide for details of count_trailing_zeros */
+
+	/* Isolate the zero: it is preceeded by a run of 1s, so add 1 to it */
+	negated = (u32) - inverted ; /* -a == ~a + 1 (mod 2^n) for n-bit numbers */
+	/* negated = xxx...x1000...0 */
+
+	isolated = negated & inverted ; /* xxx...x1000...0 & zzz...z1000...0, zs are ~xs */
+	/* And so the first zero bit is in the same position as the 1 == number of 1s that preceeded it
+	 * Note that the output is zero if value was all 1s */
+
+	leading_zeros = _mali_osk_clz(isolated);
+
+	return 31 - leading_zeros;
+}
+
+
+/** @defgroup _mali_osk_bitops OSK Non-atomic Bit-operations
+ * @{ */
+
+/**
+ * These bit-operations do not work atomically, and so locks must be used if
+ * atomicity is required.
+ *
+ * Reference implementations for Little Endian are provided, and so it should
+ * not normally be necessary to re-implement these. Efficient bit-twiddling
+ * techniques are used where possible, implemented in portable C.
+ *
+ * Note that these reference implementations rely on _mali_osk_clz() being
+ * implemented.
+ */
+
+/** @brief Clear a bit in a sequence of 32-bit words
+ * @param nr bit number to clear, starting from the (Little-endian) least
+ * significant bit
+ * @param addr starting point for counting.
+ */
+MALI_STATIC_INLINE void _mali_osk_clear_nonatomic_bit(u32 nr, u32 *addr)
+{
+	addr += nr >> 5; /* find the correct word */
+	nr = nr & ((1 << 5) - 1); /* The bit number within the word */
+
+	_mali_internal_clear_bit(nr, addr);
+}
+
+/** @brief Set a bit in a sequence of 32-bit words
+ * @param nr bit number to set, starting from the (Little-endian) least
+ * significant bit
+ * @param addr starting point for counting.
+ */
+MALI_STATIC_INLINE void _mali_osk_set_nonatomic_bit(u32 nr, u32 *addr)
+{
+	addr += nr >> 5; /* find the correct word */
+	nr = nr & ((1 << 5) - 1); /* The bit number within the word */
+
+	_mali_internal_set_bit(nr, addr);
+}
+
+/** @brief Test a bit in a sequence of 32-bit words
+ * @param nr bit number to test, starting from the (Little-endian) least
+ * significant bit
+ * @param addr starting point for counting.
+ * @return zero if bit was clear, non-zero if set. Do not rely on the return
+ * value being related to the actual word under test.
+ */
+MALI_STATIC_INLINE u32 _mali_osk_test_bit(u32 nr, u32 *addr)
+{
+	addr += nr >> 5; /* find the correct word */
+	nr = nr & ((1 << 5) - 1); /* The bit number within the word */
+
+	return _mali_internal_test_bit(nr, *addr);
+}
+
+/* Return maxbit if not found */
+/** @brief Find the first zero bit in a sequence of 32-bit words
+ * @param addr starting point for search.
+ * @param maxbit the maximum number of bits to search
+ * @return the number of the first zero bit found, or maxbit if none were found
+ * in the specified range.
+ */
+MALI_STATIC_INLINE u32 _mali_osk_find_first_zero_bit(const u32 *addr, u32 maxbit)
+{
+	u32 total;
+
+	for (total = 0; total < maxbit; total += 32, ++addr) {
+		int result;
+		result = _mali_internal_find_first_zero_bit(*addr);
+
+		/* non-negative signifies the bit was found */
+		if (result >= 0) {
+			total += (u32)result;
+			break;
+		}
+	}
+
+	/* Now check if we reached maxbit or above */
+	if (total >= maxbit) {
+		total = maxbit;
+	}
+
+	return total; /* either the found bit nr, or maxbit if not found */
+}
+/** @} */ /* end group _mali_osk_bitops */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_OSK_BITOPS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_osk_list.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_osk_list.h
@@ -0,0 +1,273 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_list.h
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#ifndef __MALI_OSK_LIST_H__
+#define __MALI_OSK_LIST_H__
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+MALI_STATIC_INLINE void __mali_osk_list_add(_mali_osk_list_t *new_entry, _mali_osk_list_t *prev, _mali_osk_list_t *next)
+{
+	next->prev = new_entry;
+	new_entry->next = next;
+	new_entry->prev = prev;
+	prev->next = new_entry;
+}
+
+MALI_STATIC_INLINE void __mali_osk_list_del(_mali_osk_list_t *prev, _mali_osk_list_t *next)
+{
+	next->prev = prev;
+	prev->next = next;
+}
+
+/** @addtogroup _mali_osk_list OSK Doubly-Linked Circular Lists
+ * @{ */
+
+/** Reference implementations of Doubly-linked Circular Lists are provided.
+ * There is often no need to re-implement these.
+ *
+ * @note The implementation may differ subtly from any lists the OS provides.
+ * For this reason, these lists should not be mixed with OS-specific lists
+ * inside the OSK/UKK implementation. */
+
+/** @brief Initialize a list to be a head of an empty list
+ * @param exp the list to initialize. */
+#define _MALI_OSK_INIT_LIST_HEAD(exp) _mali_osk_list_init(exp)
+
+/** @brief Define a list variable, which is uninitialized.
+ * @param exp the name of the variable that the list will be defined as. */
+#define _MALI_OSK_LIST_HEAD(exp) _mali_osk_list_t exp
+
+/** @brief Define a list variable, which is initialized.
+ * @param exp the name of the variable that the list will be defined as. */
+#define _MALI_OSK_LIST_HEAD_STATIC_INIT(exp) _mali_osk_list_t exp = { &exp, &exp }
+
+/** @brief Initialize a list element.
+ *
+ * All list elements must be initialized before use.
+ *
+ * Do not use on any list element that is present in a list without using
+ * _mali_osk_list_del first, otherwise this will break the list.
+ *
+ * @param list the list element to initialize
+ */
+MALI_STATIC_INLINE void _mali_osk_list_init(_mali_osk_list_t *list)
+{
+	list->next = list;
+	list->prev = list;
+}
+
+/** @brief Insert a single list element after an entry in a list
+ *
+ * As an example, if this is inserted to the head of a list, then this becomes
+ * the first element of the list.
+ *
+ * Do not use to move list elements from one list to another, as it will break
+ * the originating list.
+ *
+ *
+ * @param newlist the list element to insert
+ * @param list the list in which to insert. The new element will be the next
+ * entry in this list
+ */
+MALI_STATIC_INLINE void _mali_osk_list_add(_mali_osk_list_t *new_entry, _mali_osk_list_t *list)
+{
+	__mali_osk_list_add(new_entry, list, list->next);
+}
+
+/** @brief Insert a single list element before an entry in a list
+ *
+ * As an example, if this is inserted to the head of a list, then this becomes
+ * the last element of the list.
+ *
+ * Do not use to move list elements from one list to another, as it will break
+ * the originating list.
+ *
+ * @param newlist the list element to insert
+ * @param list the list in which to insert. The new element will be the previous
+ * entry in this list
+ */
+MALI_STATIC_INLINE void _mali_osk_list_addtail(_mali_osk_list_t *new_entry, _mali_osk_list_t *list)
+{
+	__mali_osk_list_add(new_entry, list->prev, list);
+}
+
+/** @brief Remove a single element from a list
+ *
+ * The element will no longer be present in the list. The removed list element
+ * will be uninitialized, and so should not be traversed. It must be
+ * initialized before further use.
+ *
+ * @param list the list element to remove.
+ */
+MALI_STATIC_INLINE void _mali_osk_list_del(_mali_osk_list_t *list)
+{
+	__mali_osk_list_del(list->prev, list->next);
+}
+
+/** @brief Remove a single element from a list, and re-initialize it
+ *
+ * The element will no longer be present in the list. The removed list element
+ * will initialized, and so can be used as normal.
+ *
+ * @param list the list element to remove and initialize.
+ */
+MALI_STATIC_INLINE void _mali_osk_list_delinit(_mali_osk_list_t *list)
+{
+	__mali_osk_list_del(list->prev, list->next);
+	_mali_osk_list_init(list);
+}
+
+/** @brief Determine whether a list is empty.
+ *
+ * An empty list is one that contains a single element that points to itself.
+ *
+ * @param list the list to check.
+ * @return non-zero if the list is empty, and zero otherwise.
+ */
+MALI_STATIC_INLINE mali_bool _mali_osk_list_empty(_mali_osk_list_t *list)
+{
+	return list->next == list;
+}
+
+/** @brief Move a list element from one list to another.
+ *
+ * The list element must be initialized.
+ *
+ * As an example, moving a list item to the head of a new list causes this item
+ * to be the first element in the new list.
+ *
+ * @param move the list element to move
+ * @param list the new list into which the element will be inserted, as the next
+ * element in the list.
+ */
+MALI_STATIC_INLINE void _mali_osk_list_move(_mali_osk_list_t *move_entry, _mali_osk_list_t *list)
+{
+	__mali_osk_list_del(move_entry->prev, move_entry->next);
+	_mali_osk_list_add(move_entry, list);
+}
+
+/** @brief Move an entire list
+ *
+ * The list element must be initialized.
+ *
+ * Allows you to move a list from one list head to another list head
+ *
+ * @param old_list The existing list head
+ * @param new_list The new list head (must be an empty list)
+ */
+MALI_STATIC_INLINE void _mali_osk_list_move_list(_mali_osk_list_t *old_list, _mali_osk_list_t *new_list)
+{
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(new_list));
+	if (!_mali_osk_list_empty(old_list)) {
+		new_list->next = old_list->next;
+		new_list->prev = old_list->prev;
+		new_list->next->prev = new_list;
+		new_list->prev->next = new_list;
+		old_list->next = old_list;
+		old_list->prev = old_list;
+	}
+}
+
+/** @brief Find the containing structure of a list
+ *
+ * When traversing a list, this is used to recover the containing structure,
+ * given that is contains a _mali_osk_list_t member.
+ *
+ * Each list must be of structures of one type, and must link the same members
+ * together, otherwise it will not be possible to correctly recover the
+ * sturctures that the lists link.
+ *
+ * @note no type or memory checking occurs to ensure that a structure does in
+ * fact exist for the list entry, and that it is being recovered with respect
+ * to the correct list member.
+ *
+ * @param ptr the pointer to the _mali_osk_list_t member in this structure
+ * @param type the type of the structure that contains the member
+ * @param member the member of the structure that ptr points to.
+ * @return a pointer to a \a type object which contains the _mali_osk_list_t
+ * \a member, as pointed to by the _mali_osk_list_t \a *ptr.
+ */
+#define _MALI_OSK_LIST_ENTRY(ptr, type, member) \
+	_MALI_OSK_CONTAINER_OF(ptr, type, member)
+
+/** @brief Enumerate a list safely
+ *
+ * With this macro, lists can be enumerated in a 'safe' manner. That is,
+ * entries can be deleted from the list without causing an error during
+ * enumeration. To achieve this, a 'temporary' pointer is required, which must
+ * be provided to the macro.
+ *
+ * Use it like a 'for()', 'while()' or 'do()' construct, and so it must be
+ * followed by a statement or compound-statement which will be executed for
+ * each list entry.
+ *
+ * Upon loop completion, providing that an early out was not taken in the
+ * loop body, then it is guaranteed that ptr->member == list, even if the loop
+ * body never executed.
+ *
+ * @param ptr a pointer to an object of type 'type', which points to the
+ * structure that contains the currently enumerated list entry.
+ * @param tmp a pointer to an object of type 'type', which must not be used
+ * inside the list-execution statement.
+ * @param list a pointer to a _mali_osk_list_t, from which enumeration will
+ * begin
+ * @param type the type of the structure that contains the _mali_osk_list_t
+ * member that is part of the list to be enumerated.
+ * @param member the _mali_osk_list_t member of the structure that is part of
+ * the list to be enumerated.
+ */
+#define _MALI_OSK_LIST_FOREACHENTRY(ptr, tmp, list, type, member)         \
+	for (ptr = _MALI_OSK_LIST_ENTRY((list)->next, type, member),      \
+	     tmp = _MALI_OSK_LIST_ENTRY(ptr->member.next, type, member);  \
+	     &ptr->member != (list);                                      \
+	     ptr = tmp,                                                   \
+	     tmp = _MALI_OSK_LIST_ENTRY(tmp->member.next, type, member))
+
+/** @brief Enumerate a list in reverse order safely
+ *
+ * This macro is identical to @ref _MALI_OSK_LIST_FOREACHENTRY, except that
+ * entries are enumerated in reverse order.
+ *
+ * @param ptr a pointer to an object of type 'type', which points to the
+ * structure that contains the currently enumerated list entry.
+ * @param tmp a pointer to an object of type 'type', which must not be used
+ * inside the list-execution statement.
+ * @param list a pointer to a _mali_osk_list_t, from which enumeration will
+ * begin
+ * @param type the type of the structure that contains the _mali_osk_list_t
+ * member that is part of the list to be enumerated.
+ * @param member the _mali_osk_list_t member of the structure that is part of
+ * the list to be enumerated.
+ */
+#define _MALI_OSK_LIST_FOREACHENTRY_REVERSE(ptr, tmp, list, type, member) \
+	for (ptr = _MALI_OSK_LIST_ENTRY((list)->prev, type, member),      \
+	     tmp = _MALI_OSK_LIST_ENTRY(ptr->member.prev, type, member);  \
+	     &ptr->member != (list);                                      \
+	     ptr = tmp,                                                   \
+	     tmp = _MALI_OSK_LIST_ENTRY(tmp->member.prev, type, member))
+
+/** @} */ /* end group _mali_osk_list */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_OSK_LIST_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_osk_mali.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_osk_mali.h
@@ -0,0 +1,151 @@
+/*
+ * Copyright (C) 2010-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_mali.h
+ * Defines the OS abstraction layer which is specific for the Mali kernel device driver (OSK)
+ */
+
+#ifndef __MALI_OSK_MALI_H__
+#define __MALI_OSK_MALI_H__
+
+#include <linux/mali/mali_utgard.h>
+#include <mali_osk.h>
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#ifdef CONFIG_MALI_DEVFREQ
+struct mali_device {
+	struct device *dev;
+#ifdef CONFIG_HAVE_CLK
+	struct clk *clock;
+#endif
+#ifdef CONFIG_REGULATOR
+	struct regulator *regulator;
+#endif
+#ifdef CONFIG_PM_DEVFREQ
+	struct devfreq_dev_profile devfreq_profile;
+	struct devfreq *devfreq;
+	unsigned long current_freq;
+	unsigned long current_voltage;
+#ifdef CONFIG_DEVFREQ_THERMAL
+	struct thermal_cooling_device *devfreq_cooling;
+#endif
+#endif
+	struct mali_pm_metrics_data mali_metrics;
+};
+#endif
+
+/** @addtogroup _mali_osk_miscellaneous
+ * @{ */
+
+/** @brief Struct with device specific configuration data
+ */
+typedef struct mali_gpu_device_data _mali_osk_device_data;
+
+#ifdef CONFIG_MALI_DT
+/** @brief Initialize those device resources when we use device tree
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_resource_initialize(void);
+#endif
+
+/** @brief Find Mali GPU HW resource
+ *
+ * @param addr Address of Mali GPU resource to find
+ * @param res Storage for resource information if resource is found.
+ * @return _MALI_OSK_ERR_OK on success, _MALI_OSK_ERR_ITEM_NOT_FOUND if resource is not found
+ */
+_mali_osk_errcode_t _mali_osk_resource_find(u32 addr, _mali_osk_resource_t *res);
+
+
+/** @brief Find Mali GPU HW base address
+ *
+ * @return 0 if resources are found, otherwise the Mali GPU component with lowest address.
+ */
+uintptr_t _mali_osk_resource_base_address(void);
+
+/** @brief Find the specific GPU resource.
+ *
+ * @return value
+ * 0x400 if Mali 400 specific GPU resource identified
+ * 0x450 if Mali 450 specific GPU resource identified
+ * 0x470 if Mali 470 specific GPU resource identified
+ *
+ */
+u32 _mali_osk_identify_gpu_resource(void);
+
+/** @brief Retrieve the Mali GPU specific data
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_device_data_get(_mali_osk_device_data *data);
+
+/** @brief Find the pmu domain config from device data.
+ *
+ * @param domain_config_array used to store pmu domain config found in device data.
+ * @param array_size is the size of array domain_config_array.
+ */
+void _mali_osk_device_data_pmu_config_get(u16 *domain_config_array, int array_size);
+
+/** @brief Get Mali PMU switch delay
+ *
+ *@return pmu switch delay if it is configured
+ */
+u32 _mali_osk_get_pmu_switch_delay(void);
+
+/** @brief Determines if Mali GPU has been configured with shared interrupts.
+ *
+ * @return MALI_TRUE if shared interrupts, MALI_FALSE if not.
+ */
+mali_bool _mali_osk_shared_interrupts(void);
+
+/** @brief Initialize the gpu secure mode.
+ * The gpu secure mode will initially be in a disabled state.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_gpu_secure_mode_init(void);
+
+/** @brief Deinitialize the gpu secure mode.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_gpu_secure_mode_deinit(void);
+
+/** @brief Reset GPU and enable the gpu secure mode.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_gpu_reset_and_secure_mode_enable(void);
+
+/** @brief Reset GPU and disable the gpu secure mode.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_gpu_reset_and_secure_mode_disable(void);
+
+/** @brief Check if the gpu secure mode has been enabled.
+ * @return MALI_TRUE if enabled, otherwise MALI_FALSE.
+ */
+mali_bool _mali_osk_gpu_secure_mode_is_enabled(void);
+
+/** @brief Check if the gpu secure mode is supported.
+ * @return MALI_TRUE if supported, otherwise MALI_FALSE.
+ */
+mali_bool _mali_osk_gpu_secure_mode_is_supported(void);
+
+
+/** @} */ /* end group _mali_osk_miscellaneous */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_OSK_MALI_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_osk_profiling.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_osk_profiling.h
@@ -0,0 +1,146 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_OSK_PROFILING_H__
+#define __MALI_OSK_PROFILING_H__
+
+#if defined(CONFIG_MALI400_PROFILING) && defined (CONFIG_TRACEPOINTS)
+
+#include "mali_linux_trace.h"
+#include "mali_profiling_events.h"
+#include "mali_profiling_gator_api.h"
+
+#define MALI_PROFILING_MAX_BUFFER_ENTRIES 1048576
+
+#define MALI_PROFILING_NO_HW_COUNTER = ((u32)-1)
+
+/** @defgroup _mali_osk_profiling External profiling connectivity
+ * @{ */
+
+/**
+ * Initialize the profiling module.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_profiling_init(mali_bool auto_start);
+
+/*
+ * Terminate the profiling module.
+ */
+void _mali_osk_profiling_term(void);
+
+/**
+ * Stop the profile sampling operation.
+ */
+void _mali_osk_profiling_stop_sampling(u32 pid);
+
+/**
+ * Start recording profiling data
+ *
+ * The specified limit will determine how large the capture buffer is.
+ * MALI_PROFILING_MAX_BUFFER_ENTRIES determines the maximum size allowed by the device driver.
+ *
+ * @param limit The desired maximum number of events to record on input, the actual maximum on output.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_profiling_start(u32 *limit);
+
+/**
+ * Add an profiling event
+ *
+ * @param event_id The event identificator.
+ * @param data0 First data parameter, depending on event_id specified.
+ * @param data1 Second data parameter, depending on event_id specified.
+ * @param data2 Third data parameter, depending on event_id specified.
+ * @param data3 Fourth data parameter, depending on event_id specified.
+ * @param data4 Fifth data parameter, depending on event_id specified.
+ */
+void    _mali_osk_profiling_add_event(u32 event_id, u32 data0, u32 data1, u32 data2, u32 data3, u32 data4);
+
+/**
+ * Report a hardware counter event.
+ *
+ * @param counter_id The ID of the counter.
+ * @param value The value of the counter.
+ */
+
+/* Call Linux tracepoint directly */
+#define _mali_osk_profiling_report_hw_counter(counter_id, value) trace_mali_hw_counter(counter_id, value)
+
+/**
+ * Report SW counters
+ *
+ * @param counters array of counter values
+ */
+void _mali_osk_profiling_report_sw_counters(u32 *counters);
+
+void _mali_osk_profiling_record_global_counters(int counter_id, u32 value);
+
+/**
+ * Stop recording profiling data
+ *
+ * @param count Returns the number of recorded events.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_profiling_stop(u32 *count);
+
+/**
+ * Retrieves the number of events that can be retrieved
+ *
+ * @return The number of recorded events that can be retrieved.
+ */
+u32 _mali_osk_profiling_get_count(void);
+
+/**
+ * Retrieve an event
+ *
+ * @param index Event index (start with 0 and continue until this function fails to retrieve all events)
+ * @param timestamp The timestamp for the retrieved event will be stored here.
+ * @param event_id The event ID for the retrieved event will be stored here.
+ * @param data The 5 data values for the retrieved event will be stored here.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_profiling_get_event(u32 index, u64 *timestamp, u32 *event_id, u32 data[5]);
+
+/**
+ * Clear the recorded buffer.
+ *
+ * This is needed in order to start another recording.
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t _mali_osk_profiling_clear(void);
+
+/**
+ * Checks if a recording of profiling data is in progress
+ *
+ * @return MALI_TRUE if recording of profiling data is in progress, MALI_FALSE if not
+ */
+mali_bool _mali_osk_profiling_is_recording(void);
+
+/**
+ * Checks if profiling data is available for retrival
+ *
+ * @return MALI_TRUE if profiling data is avaiable, MALI_FALSE if not
+ */
+mali_bool _mali_osk_profiling_have_recording(void);
+
+/** @} */ /* end group _mali_osk_profiling */
+
+#else /* defined(CONFIG_MALI400_PROFILING)  && defined(CONFIG_TRACEPOINTS) */
+
+/* Dummy add_event, for when profiling is disabled. */
+
+#define _mali_osk_profiling_add_event(event_id, data0, data1, data2, data3, data4)
+
+#endif /* defined(CONFIG_MALI400_PROFILING)  && defined(CONFIG_TRACEPOINTS) */
+
+#endif /* __MALI_OSK_PROFILING_H__ */
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_osk_types.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_osk_types.h
@@ -0,0 +1,471 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_types.h
+ * Defines types of the OS abstraction layer for the kernel device driver (OSK)
+ */
+
+#ifndef __MALI_OSK_TYPES_H__
+#define __MALI_OSK_TYPES_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @addtogroup uddapi Unified Device Driver (UDD) APIs
+ *
+ * @{
+ */
+
+/**
+ * @addtogroup oskapi UDD OS Abstraction for Kernel-side (OSK) APIs
+ *
+ * @{
+ */
+
+/** @defgroup _mali_osk_miscellaneous OSK Miscellaneous functions, constants and types
+ * @{ */
+
+/* Define integer types used by OSK. Note: these currently clash with Linux so we only define them if not defined already */
+#ifndef __KERNEL__
+typedef unsigned char      u8;
+typedef signed char        s8;
+typedef unsigned short     u16;
+typedef signed short       s16;
+typedef unsigned int       u32;
+typedef signed int         s32;
+typedef unsigned long long u64;
+#define BITS_PER_LONG (sizeof(long)*8)
+#else
+/* Ensure Linux types u32, etc. are defined */
+#include <linux/types.h>
+#endif
+
+/** @brief Mali Boolean type which uses MALI_TRUE and MALI_FALSE
+  */
+typedef unsigned long mali_bool;
+
+#ifndef MALI_TRUE
+#define MALI_TRUE ((mali_bool)1)
+#endif
+
+#ifndef MALI_FALSE
+#define MALI_FALSE ((mali_bool)0)
+#endif
+
+#define MALI_HW_CORE_NO_COUNTER     ((u32)-1)
+
+
+#define MALI_S32_MAX 0x7fffffff
+
+/**
+ * @brief OSK Error codes
+ *
+ * Each OS may use its own set of error codes, and may require that the
+ * User/Kernel interface take certain error code. This means that the common
+ * error codes need to be sufficiently rich to pass the correct error code
+ * thorugh from the OSK to U/K layer, across all OSs.
+ *
+ * The result is that some error codes will appear redundant on some OSs.
+ * Under all OSs, the OSK layer must translate native OS error codes to
+ * _mali_osk_errcode_t codes. Similarly, the U/K layer must translate from
+ * _mali_osk_errcode_t codes to native OS error codes.
+ */
+typedef enum {
+	_MALI_OSK_ERR_OK = 0, /**< Success. */
+	_MALI_OSK_ERR_FAULT = -1, /**< General non-success */
+	_MALI_OSK_ERR_INVALID_FUNC = -2, /**< Invalid function requested through User/Kernel interface (e.g. bad IOCTL number) */
+	_MALI_OSK_ERR_INVALID_ARGS = -3, /**< Invalid arguments passed through User/Kernel interface */
+	_MALI_OSK_ERR_NOMEM = -4, /**< Insufficient memory */
+	_MALI_OSK_ERR_TIMEOUT = -5, /**< Timeout occurred */
+	_MALI_OSK_ERR_RESTARTSYSCALL = -6, /**< Special: On certain OSs, must report when an interruptable mutex is interrupted. Ignore otherwise. */
+	_MALI_OSK_ERR_ITEM_NOT_FOUND = -7, /**< Table Lookup failed */
+	_MALI_OSK_ERR_BUSY = -8, /**< Device/operation is busy. Try again later */
+	_MALI_OSK_ERR_UNSUPPORTED = -9, /**< Optional part of the interface used, and is unsupported */
+} _mali_osk_errcode_t;
+
+/** @} */ /* end group _mali_osk_miscellaneous */
+
+/** @defgroup _mali_osk_wq OSK work queues
+ * @{ */
+
+/** @brief Private type for work objects */
+typedef struct _mali_osk_wq_work_s _mali_osk_wq_work_t;
+typedef struct _mali_osk_wq_delayed_work_s _mali_osk_wq_delayed_work_t;
+
+/** @brief Work queue handler function
+ *
+ * This function type is called when the work is scheduled by the work queue,
+ * e.g. as an IRQ bottom-half handler.
+ *
+ * Refer to \ref _mali_osk_wq_schedule_work() for more information on the
+ * work-queue and work handlers.
+ *
+ * @param arg resource-specific data
+ */
+typedef void (*_mali_osk_wq_work_handler_t)(void *arg);
+
+/* @} */ /* end group _mali_osk_wq */
+
+/** @defgroup _mali_osk_irq OSK IRQ handling
+ * @{ */
+
+/** @brief Private type for IRQ handling objects */
+typedef struct _mali_osk_irq_t_struct _mali_osk_irq_t;
+
+/** @brief Optional function to trigger an irq from a resource
+ *
+ * This function is implemented by the common layer to allow probing of a resource's IRQ.
+ * @param arg resource-specific data */
+typedef void (*_mali_osk_irq_trigger_t)(void *arg);
+
+/** @brief Optional function to acknowledge an irq from a resource
+ *
+ * This function is implemented by the common layer to allow probing of a resource's IRQ.
+ * @param arg resource-specific data
+ * @return _MALI_OSK_ERR_OK if the IRQ was successful, or a suitable _mali_osk_errcode_t on failure. */
+typedef _mali_osk_errcode_t (*_mali_osk_irq_ack_t)(void *arg);
+
+/** @brief IRQ 'upper-half' handler callback.
+ *
+ * This function is implemented by the common layer to do the initial handling of a
+ * resource's IRQ. This maps on to the concept of an ISR that does the minimum
+ * work necessary before handing off to an IST.
+ *
+ * The communication of the resource-specific data from the ISR to the IST is
+ * handled by the OSK implementation.
+ *
+ * On most systems, the IRQ upper-half handler executes in IRQ context.
+ * Therefore, the system may have restrictions about what can be done in this
+ * context
+ *
+ * If an IRQ upper-half handler requires more work to be done than can be
+ * acheived in an IRQ context, then it may defer the work with
+ * _mali_osk_wq_schedule_work(). Refer to \ref _mali_osk_wq_create_work() for
+ * more information.
+ *
+ * @param arg resource-specific data
+ * @return _MALI_OSK_ERR_OK if the IRQ was correctly handled, or a suitable
+ * _mali_osk_errcode_t otherwise.
+ */
+typedef _mali_osk_errcode_t (*_mali_osk_irq_uhandler_t)(void *arg);
+
+
+/** @} */ /* end group _mali_osk_irq */
+
+
+/** @defgroup _mali_osk_atomic OSK Atomic counters
+ * @{ */
+
+/** @brief Public type of atomic counters
+ *
+ * This is public for allocation on stack. On systems that support it, this is just a single 32-bit value.
+ * On others, it could be encapsulating an object stored elsewhere.
+ *
+ * Regardless of implementation, the \ref _mali_osk_atomic functions \b must be used
+ * for all accesses to the variable's value, even if atomicity is not required.
+ * Do not access u.val or u.obj directly.
+ */
+typedef struct {
+	union {
+		u32 val;
+		void *obj;
+	} u;
+} _mali_osk_atomic_t;
+/** @} */ /* end group _mali_osk_atomic */
+
+
+/** @defgroup _mali_osk_lock OSK Mutual Exclusion Locks
+ * @{ */
+
+
+/** @brief OSK Mutual Exclusion Lock ordered list
+ *
+ * This lists the various types of locks in the system and is used to check
+ * that locks are taken in the correct order.
+ *
+ * - Holding more than one lock of the same order at the same time is not
+ *   allowed.
+ * - Taking a lock of a lower order than the highest-order lock currently held
+ *   is not allowed.
+ *
+ */
+typedef enum {
+	/*  ||    Locks    ||  */
+	/*  ||   must be   ||  */
+	/* _||_  taken in _||_ */
+	/* \  /    this   \  / */
+	/*  \/    order!   \/  */
+
+	_MALI_OSK_LOCK_ORDER_FIRST = 0,
+
+	_MALI_OSK_LOCK_ORDER_SESSIONS,
+	_MALI_OSK_LOCK_ORDER_MEM_SESSION,
+	_MALI_OSK_LOCK_ORDER_MEM_INFO,
+	_MALI_OSK_LOCK_ORDER_MEM_PT_CACHE,
+	_MALI_OSK_LOCK_ORDER_DESCRIPTOR_MAP,
+	_MALI_OSK_LOCK_ORDER_PM_EXECUTION,
+	_MALI_OSK_LOCK_ORDER_EXECUTOR,
+	_MALI_OSK_LOCK_ORDER_TIMELINE_SYSTEM,
+	_MALI_OSK_LOCK_ORDER_SCHEDULER,
+	_MALI_OSK_LOCK_ORDER_SCHEDULER_DEFERRED,
+	_MALI_OSK_LOCK_ORDER_PROFILING,
+	_MALI_OSK_LOCK_ORDER_L2,
+	_MALI_OSK_LOCK_ORDER_L2_COMMAND,
+	_MALI_OSK_LOCK_ORDER_UTILIZATION,
+	_MALI_OSK_LOCK_ORDER_SESSION_PENDING_JOBS,
+	_MALI_OSK_LOCK_ORDER_PM_STATE,
+
+	_MALI_OSK_LOCK_ORDER_LAST,
+} _mali_osk_lock_order_t;
+
+
+/** @brief OSK Mutual Exclusion Lock flags type
+ *
+ * - Any lock can use the order parameter.
+ */
+typedef enum {
+	_MALI_OSK_LOCKFLAG_UNORDERED        = 0x1, /**< Indicate that the order of this lock should not be checked */
+	_MALI_OSK_LOCKFLAG_ORDERED          = 0x2,
+	/** @enum _mali_osk_lock_flags_t
+	 *
+	 * Flags from 0x10000--0x80000000 are RESERVED for User-mode */
+
+} _mali_osk_lock_flags_t;
+
+/** @brief Mutual Exclusion Lock Mode Optimization hint
+ *
+ * The lock mode is used to implement the read/write locking of locks when we call
+ * functions _mali_osk_mutex_rw_init/wait/signal/term/. In this case, the RO mode can
+ * be used to allow multiple concurrent readers, but no writers. The RW mode is used for
+ * writers, and so will wait for all readers to release the lock (if any present).
+ * Further readers and writers will wait until the writer releases the lock.
+ *
+ * The mode is purely an optimization hint: for example, it is permissible for
+ * all locks to behave in RW mode, regardless of that supplied.
+ *
+ * It is an error to attempt to use locks in anything other that RW mode when
+ * call functions _mali_osk_mutex_rw_wait/signal().
+ *
+ */
+typedef enum {
+	_MALI_OSK_LOCKMODE_UNDEF = -1,  /**< Undefined lock mode. For internal use only */
+	_MALI_OSK_LOCKMODE_RW    = 0x0, /**< Read-write mode, default. All readers and writers are mutually-exclusive */
+	_MALI_OSK_LOCKMODE_RO,          /**< Read-only mode, to support multiple concurrent readers, but mutual exclusion in the presence of writers. */
+	/** @enum _mali_osk_lock_mode_t
+	 *
+	 * Lock modes 0x40--0x7F are RESERVED for User-mode */
+} _mali_osk_lock_mode_t;
+
+/** @brief Private types for Mutual Exclusion lock objects */
+typedef struct _mali_osk_lock_debug_s _mali_osk_lock_debug_t;
+typedef struct _mali_osk_spinlock_s _mali_osk_spinlock_t;
+typedef struct _mali_osk_spinlock_irq_s _mali_osk_spinlock_irq_t;
+typedef struct _mali_osk_mutex_s _mali_osk_mutex_t;
+typedef struct _mali_osk_mutex_rw_s _mali_osk_mutex_rw_t;
+
+/** @} */ /* end group _mali_osk_lock */
+
+/** @defgroup _mali_osk_low_level_memory OSK Low-level Memory Operations
+ * @{ */
+
+/**
+ * @brief Private data type for use in IO accesses to/from devices.
+ *
+ * This represents some range that is accessible from the device. Examples
+ * include:
+ * - Device Registers, which could be readable and/or writeable.
+ * - Memory that the device has access to, for storing configuration structures.
+ *
+ * Access to this range must be made through the _mali_osk_mem_ioread32() and
+ * _mali_osk_mem_iowrite32() functions.
+ */
+typedef struct _mali_io_address *mali_io_address;
+
+/** @defgroup _MALI_OSK_CPU_PAGE CPU Physical page size macros.
+ *
+ * The order of the page size is supplied for
+ * ease of use by algorithms that might require it, since it is easier to know
+ * it ahead of time rather than calculating it.
+ *
+ * The Mali Page Mask macro masks off the lower bits of a physical address to
+ * give the start address of the page for that physical address.
+ *
+ * @note The Mali device driver code is designed for systems with 4KB page size.
+ * Changing these macros will not make the entire Mali device driver work with
+ * page sizes other than 4KB.
+ *
+ * @note The CPU Physical Page Size has been assumed to be the same as the Mali
+ * Physical Page Size.
+ *
+ * @{
+ */
+
+/** CPU Page Order, as log to base 2 of the Page size. @see _MALI_OSK_CPU_PAGE_SIZE */
+#define _MALI_OSK_CPU_PAGE_ORDER ((u32)12)
+/** CPU Page Size, in bytes.               */
+#define _MALI_OSK_CPU_PAGE_SIZE (((u32)1) << (_MALI_OSK_CPU_PAGE_ORDER))
+/** CPU Page Mask, which masks off the offset within a page */
+#define _MALI_OSK_CPU_PAGE_MASK (~((((u32)1) << (_MALI_OSK_CPU_PAGE_ORDER)) - ((u32)1)))
+/** @} */ /* end of group _MALI_OSK_CPU_PAGE */
+
+/** @defgroup _MALI_OSK_MALI_PAGE Mali Physical Page size macros
+ *
+ * Mali Physical page size macros. The order of the page size is supplied for
+ * ease of use by algorithms that might require it, since it is easier to know
+ * it ahead of time rather than calculating it.
+ *
+ * The Mali Page Mask macro masks off the lower bits of a physical address to
+ * give the start address of the page for that physical address.
+ *
+ * @note The Mali device driver code is designed for systems with 4KB page size.
+ * Changing these macros will not make the entire Mali device driver work with
+ * page sizes other than 4KB.
+ *
+ * @note The Mali Physical Page Size has been assumed to be the same as the CPU
+ * Physical Page Size.
+ *
+ * @{
+ */
+
+/** Mali Page Order, as log to base 2 of the Page size. @see _MALI_OSK_MALI_PAGE_SIZE */
+#define _MALI_OSK_MALI_PAGE_ORDER PAGE_SHIFT
+/** Mali Page Size, in bytes.               */
+#define _MALI_OSK_MALI_PAGE_SIZE PAGE_SIZE
+/** Mali Page Mask, which masks off the offset within a page */
+#define _MALI_OSK_MALI_PAGE_MASK PAGE_MASK
+/** @} */ /* end of group _MALI_OSK_MALI_PAGE*/
+
+/** @brief flags for mapping a user-accessible memory range
+ *
+ * Where a function with prefix '_mali_osk_mem_mapregion' accepts flags as one
+ * of the function parameters, it will use one of these. These allow per-page
+ * control over mappings. Compare with the mali_memory_allocation_flag type,
+ * which acts over an entire range
+ *
+ * These may be OR'd together with bitwise OR (|), but must be cast back into
+ * the type after OR'ing.
+ */
+typedef enum {
+	_MALI_OSK_MEM_MAPREGION_FLAG_OS_ALLOCATED_PHYSADDR = 0x1, /**< Physical address is OS Allocated */
+} _mali_osk_mem_mapregion_flags_t;
+/** @} */ /* end group _mali_osk_low_level_memory */
+
+/** @defgroup _mali_osk_notification OSK Notification Queues
+ * @{ */
+
+/** @brief Private type for notification queue objects */
+typedef struct _mali_osk_notification_queue_t_struct _mali_osk_notification_queue_t;
+
+/** @brief Public notification data object type */
+typedef struct _mali_osk_notification_t_struct {
+	u32 notification_type;   /**< The notification type */
+	u32 result_buffer_size; /**< Size of the result buffer to copy to user space */
+	void *result_buffer;    /**< Buffer containing any type specific data */
+} _mali_osk_notification_t;
+
+/** @} */ /* end group _mali_osk_notification */
+
+
+/** @defgroup _mali_osk_timer OSK Timer Callbacks
+ * @{ */
+
+/** @brief Function to call when a timer expires
+ *
+ * When a timer expires, this function is called. Note that on many systems,
+ * a timer callback will be executed in IRQ context. Therefore, restrictions
+ * may apply on what can be done inside the timer callback.
+ *
+ * If a timer requires more work to be done than can be acheived in an IRQ
+ * context, then it may defer the work with a work-queue. For example, it may
+ * use \ref _mali_osk_wq_schedule_work() to make use of a bottom-half handler
+ * to carry out the remaining work.
+ *
+ * Stopping the timer with \ref _mali_osk_timer_del() blocks on compeletion of
+ * the callback. Therefore, the callback may not obtain any mutexes also held
+ * by any callers of _mali_osk_timer_del(). Otherwise, a deadlock may occur.
+ *
+ * @param arg Function-specific data */
+typedef void (*_mali_osk_timer_callback_t)(void *arg);
+
+/** @brief Private type for Timer Callback Objects */
+typedef struct _mali_osk_timer_t_struct _mali_osk_timer_t;
+/** @} */ /* end group _mali_osk_timer */
+
+
+/** @addtogroup _mali_osk_list OSK Doubly-Linked Circular Lists
+ * @{ */
+
+/** @brief Public List objects.
+ *
+ * To use, add a _mali_osk_list_t member to the structure that may become part
+ * of a list. When traversing the _mali_osk_list_t objects, use the
+ * _MALI_OSK_CONTAINER_OF() macro to recover the structure from its
+ *_mali_osk_list_t member
+ *
+ * Each structure may have multiple _mali_osk_list_t members, so that the
+ * structure is part of multiple lists. When traversing lists, ensure that the
+ * correct _mali_osk_list_t member is used, because type-checking will be
+ * lost by the compiler.
+ */
+typedef struct _mali_osk_list_s {
+	struct _mali_osk_list_s *next;
+	struct _mali_osk_list_s *prev;
+} _mali_osk_list_t;
+/** @} */ /* end group _mali_osk_list */
+
+/** @addtogroup _mali_osk_miscellaneous
+ * @{ */
+
+/** @brief resource description struct
+ *
+ * Platform independent representation of a Mali HW resource
+ */
+typedef struct _mali_osk_resource {
+	const char *description;        /**< short description of the resource */
+	uintptr_t base;                 /**< Physical base address of the resource, as seen by Mali resources. */
+	const char *irq_name;           /**< Name of irq belong to this resource */
+	u32 irq;                        /**< IRQ number delivered to the CPU, or -1 to tell the driver to probe for it (if possible) */
+} _mali_osk_resource_t;
+/** @} */ /* end group _mali_osk_miscellaneous */
+
+/** @defgroup _mali_osk_wait_queue OSK Wait Queue functionality
+ * @{ */
+/** @brief Private type for wait queue objects */
+typedef struct _mali_osk_wait_queue_t_struct _mali_osk_wait_queue_t;
+/** @} */ /* end group _mali_osk_wait_queue */
+
+/** @} */ /* end group osuapi */
+
+/** @} */ /* end group uddapi */
+
+/** @brief Mali print ctx type which uses seq_file
+  */
+typedef struct seq_file _mali_osk_print_ctx;
+
+#define _MALI_OSK_BITMAP_INVALIDATE_INDEX -1
+
+typedef struct _mali_osk_bitmap {
+	u32         reserve;
+	u32         last;
+	u32         max;
+	u32         avail;
+	_mali_osk_spinlock_t   *lock;
+	unsigned long          *table;
+} _mali_osk_bitmap_t;
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_OSK_TYPES_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pm.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pm.c
@@ -0,0 +1,1363 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_pm.h"
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_scheduler.h"
+#include "mali_group.h"
+#include "mali_pm_domain.h"
+#include "mali_pmu.h"
+
+#include "mali_executor.h"
+#include "mali_control_timer.h"
+
+#if defined(DEBUG)
+u32 num_pm_runtime_resume = 0;
+u32 num_pm_updates = 0;
+u32 num_pm_updates_up = 0;
+u32 num_pm_updates_down = 0;
+#endif
+
+#define MALI_PM_DOMAIN_DUMMY_MASK (1 << MALI_DOMAIN_INDEX_DUMMY)
+
+/* lock protecting power state (including pm_domains) */
+static _mali_osk_spinlock_irq_t *pm_lock_state = NULL;
+
+/* the wanted domain mask (protected by pm_lock_state) */
+static u32 pd_mask_wanted = 0;
+
+/* used to deferring the actual power changes */
+static _mali_osk_wq_work_t *pm_work = NULL;
+
+/* lock protecting power change execution */
+static _mali_osk_mutex_t *pm_lock_exec = NULL;
+
+/* PMU domains which are actually powered on (protected by pm_lock_exec) */
+static u32 pmu_mask_current = 0;
+
+/*
+ * domains which marked as powered on (protected by pm_lock_exec)
+ * This can be different from pmu_mask_current right after GPU power on
+ * if the PMU domains default to powered up.
+ */
+static u32 pd_mask_current = 0;
+
+static u16 domain_config[MALI_MAX_NUMBER_OF_DOMAINS] = {
+	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+	1 << MALI_DOMAIN_INDEX_DUMMY
+};
+
+/* The relative core power cost */
+#define MALI_GP_COST 3
+#define MALI_PP_COST 6
+#define MALI_L2_COST 1
+
+/*
+ *We have MALI_MAX_NUMBER_OF_PP_PHYSICAL_CORES + 1 rows in this matrix
+ *because we mush store the mask of different pp cores: 0, 1, 2, 3, 4, 5, 6, 7, 8.
+ */
+static int mali_pm_domain_power_cost_result[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS + 1][MALI_MAX_NUMBER_OF_DOMAINS];
+/*
+ * Keep track of runtime PM state, so that we know
+ * how to resume during OS resume.
+ */
+#ifdef CONFIG_PM_RUNTIME
+static mali_bool mali_pm_runtime_active = MALI_FALSE;
+#else
+/* when kernel don't enable PM_RUNTIME, set the flag always true,
+ * for GPU will not power off by runtime */
+static mali_bool mali_pm_runtime_active = MALI_TRUE;
+#endif
+
+static void mali_pm_state_lock(void);
+static void mali_pm_state_unlock(void);
+static _mali_osk_errcode_t mali_pm_create_pm_domains(void);
+static void mali_pm_set_pmu_domain_config(void);
+static u32 mali_pm_get_registered_cores_mask(void);
+static void mali_pm_update_sync_internal(void);
+static mali_bool mali_pm_common_suspend(void);
+static void mali_pm_update_work(void *data);
+#if defined(DEBUG)
+const char *mali_pm_mask_to_string(u32 mask);
+const char *mali_pm_group_stats_to_string(void);
+#endif
+
+_mali_osk_errcode_t mali_pm_initialize(void)
+{
+	_mali_osk_errcode_t err;
+	struct mali_pmu_core *pmu;
+
+	pm_lock_state = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_ORDERED,
+			_MALI_OSK_LOCK_ORDER_PM_STATE);
+	if (NULL == pm_lock_state) {
+		mali_pm_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	pm_lock_exec = _mali_osk_mutex_init(_MALI_OSK_LOCKFLAG_ORDERED,
+					    _MALI_OSK_LOCK_ORDER_PM_STATE);
+	if (NULL == pm_lock_exec) {
+		mali_pm_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	pm_work = _mali_osk_wq_create_work(mali_pm_update_work, NULL);
+	if (NULL == pm_work) {
+		mali_pm_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	pmu = mali_pmu_get_global_pmu_core();
+	if (NULL != pmu) {
+		/*
+		 * We have a Mali PMU, set the correct domain
+		 * configuration (default or custom)
+		 */
+
+		u32 registered_cores_mask;
+
+		mali_pm_set_pmu_domain_config();
+
+		registered_cores_mask = mali_pm_get_registered_cores_mask();
+		mali_pmu_set_registered_cores_mask(pmu, registered_cores_mask);
+
+		MALI_DEBUG_ASSERT(0 == pd_mask_wanted);
+	}
+
+	/* Create all power domains needed (at least one dummy domain) */
+	err = mali_pm_create_pm_domains();
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_pm_terminate();
+		return err;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_pm_terminate(void)
+{
+	if (NULL != pm_work) {
+		_mali_osk_wq_delete_work(pm_work);
+		pm_work = NULL;
+	}
+
+	mali_pm_domain_terminate();
+
+	if (NULL != pm_lock_exec) {
+		_mali_osk_mutex_term(pm_lock_exec);
+		pm_lock_exec = NULL;
+	}
+
+	if (NULL != pm_lock_state) {
+		_mali_osk_spinlock_irq_term(pm_lock_state);
+		pm_lock_state = NULL;
+	}
+}
+
+struct mali_pm_domain *mali_pm_register_l2_cache(u32 domain_index,
+		struct mali_l2_cache_core *l2_cache)
+{
+	struct mali_pm_domain *domain;
+
+	domain = mali_pm_domain_get_from_mask(domain_config[domain_index]);
+	if (NULL == domain) {
+		MALI_DEBUG_ASSERT(0 == domain_config[domain_index]);
+		domain = mali_pm_domain_get_from_index(
+				 MALI_DOMAIN_INDEX_DUMMY);
+		domain_config[domain_index] = MALI_PM_DOMAIN_DUMMY_MASK;
+	} else {
+		MALI_DEBUG_ASSERT(0 != domain_config[domain_index]);
+	}
+
+	MALI_DEBUG_ASSERT(NULL != domain);
+
+	mali_pm_domain_add_l2_cache(domain, l2_cache);
+
+	return domain; /* return the actual domain this was registered in */
+}
+
+struct mali_pm_domain *mali_pm_register_group(u32 domain_index,
+		struct mali_group *group)
+{
+	struct mali_pm_domain *domain;
+
+	domain = mali_pm_domain_get_from_mask(domain_config[domain_index]);
+	if (NULL == domain) {
+		MALI_DEBUG_ASSERT(0 == domain_config[domain_index]);
+		domain = mali_pm_domain_get_from_index(
+				 MALI_DOMAIN_INDEX_DUMMY);
+		domain_config[domain_index] = MALI_PM_DOMAIN_DUMMY_MASK;
+	} else {
+		MALI_DEBUG_ASSERT(0 != domain_config[domain_index]);
+	}
+
+	MALI_DEBUG_ASSERT(NULL != domain);
+
+	mali_pm_domain_add_group(domain, group);
+
+	return domain; /* return the actual domain this was registered in */
+}
+
+mali_bool mali_pm_get_domain_refs(struct mali_pm_domain **domains,
+				  struct mali_group **groups,
+				  u32 num_domains)
+{
+	mali_bool ret = MALI_TRUE; /* Assume all is powered on instantly */
+	u32 i;
+
+	mali_pm_state_lock();
+
+	for (i = 0; i < num_domains; i++) {
+		MALI_DEBUG_ASSERT_POINTER(domains[i]);
+		pd_mask_wanted |= mali_pm_domain_ref_get(domains[i]);
+		if (MALI_FALSE == mali_pm_domain_power_is_on(domains[i])) {
+			/*
+			 * Tell caller that the corresponding group
+			 * was not already powered on.
+			 */
+			ret = MALI_FALSE;
+		} else {
+			/*
+			 * There is a time gap between we power on the domain and
+			 * set the power state of the corresponding groups to be on.
+			 */
+			if (NULL != groups[i] &&
+			    MALI_FALSE == mali_group_power_is_on(groups[i])) {
+				ret = MALI_FALSE;
+			}
+		}
+	}
+
+	MALI_DEBUG_PRINT(3, ("PM: wanted domain mask = 0x%08X (get refs)\n", pd_mask_wanted));
+
+	mali_pm_state_unlock();
+
+	return ret;
+}
+
+mali_bool mali_pm_put_domain_refs(struct mali_pm_domain **domains,
+				  u32 num_domains)
+{
+	u32 mask = 0;
+	mali_bool ret;
+	u32 i;
+
+	mali_pm_state_lock();
+
+	for (i = 0; i < num_domains; i++) {
+		MALI_DEBUG_ASSERT_POINTER(domains[i]);
+		mask |= mali_pm_domain_ref_put(domains[i]);
+	}
+
+	if (0 == mask) {
+		/* return false, all domains should still stay on */
+		ret = MALI_FALSE;
+	} else {
+		/* Assert that we are dealing with a change */
+		MALI_DEBUG_ASSERT((pd_mask_wanted & mask) == mask);
+
+		/* Update our desired domain mask */
+		pd_mask_wanted &= ~mask;
+
+		/* return true; one or more domains can now be powered down */
+		ret = MALI_TRUE;
+	}
+
+	MALI_DEBUG_PRINT(3, ("PM: wanted domain mask = 0x%08X (put refs)\n", pd_mask_wanted));
+
+	mali_pm_state_unlock();
+
+	return ret;
+}
+
+void mali_pm_init_begin(void)
+{
+	struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+
+	_mali_osk_pm_dev_ref_get_sync();
+
+	/* Ensure all PMU domains are on */
+	if (NULL != pmu) {
+		mali_pmu_power_up_all(pmu);
+	}
+}
+
+void mali_pm_init_end(void)
+{
+	struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+
+	/* Ensure all PMU domains are off */
+	if (NULL != pmu) {
+		mali_pmu_power_down_all(pmu);
+	}
+
+	_mali_osk_pm_dev_ref_put();
+	_mali_osk_pm_dev_barrier();
+}
+
+void mali_pm_update_sync(void)
+{
+	mali_pm_exec_lock();
+
+	if (MALI_TRUE == mali_pm_runtime_active) {
+		/*
+		 * Only update if GPU is powered on.
+		 * Deactivation of the last group will result in both a
+		 * deferred runtime PM suspend operation and
+		 * deferred execution of this function.
+		 * mali_pm_runtime_active will be false if runtime PM
+		 * executed first and thus the GPU is now fully powered off.
+		 */
+		mali_pm_update_sync_internal();
+	}
+
+	mali_pm_exec_unlock();
+}
+
+void mali_pm_update_async(void)
+{
+	_mali_osk_wq_schedule_work(pm_work);
+}
+
+void mali_pm_os_suspend(mali_bool os_suspend)
+{
+	int ret;
+
+	MALI_DEBUG_PRINT(3, ("Mali PM: OS suspend\n"));
+
+	/* Suspend execution of all jobs, and go to inactive state */
+	mali_executor_suspend();
+
+	if (os_suspend) {
+		mali_control_timer_suspend(MALI_TRUE);
+	}
+
+	mali_pm_exec_lock();
+
+	ret = mali_pm_common_suspend();
+
+	MALI_DEBUG_ASSERT(MALI_TRUE == ret);
+	MALI_IGNORE(ret);
+
+	mali_pm_exec_unlock();
+}
+
+void mali_pm_os_resume(void)
+{
+	struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+
+	MALI_DEBUG_PRINT(3, ("Mali PM: OS resume\n"));
+
+	mali_pm_exec_lock();
+
+#if defined(DEBUG)
+	mali_pm_state_lock();
+
+	/* Assert that things are as we left them in os_suspend(). */
+	MALI_DEBUG_ASSERT(0 == pd_mask_wanted);
+	MALI_DEBUG_ASSERT(0 == pd_mask_current);
+	MALI_DEBUG_ASSERT(0 == pmu_mask_current);
+
+	MALI_DEBUG_ASSERT(MALI_TRUE == mali_pm_domain_all_unused());
+
+	mali_pm_state_unlock();
+#endif
+
+	if (MALI_TRUE == mali_pm_runtime_active) {
+		/* Runtime PM was active, so reset PMU */
+		if (NULL != pmu) {
+			mali_pmu_reset(pmu);
+			pmu_mask_current = mali_pmu_get_mask(pmu);
+
+			MALI_DEBUG_PRINT(3, ("Mali PM: OS resume 0x%x \n", pmu_mask_current));
+		}
+
+		mali_pm_update_sync_internal();
+	}
+
+	mali_pm_exec_unlock();
+
+	/* Start executing jobs again */
+	mali_executor_resume();
+}
+
+mali_bool mali_pm_runtime_suspend(void)
+{
+	mali_bool ret;
+
+	MALI_DEBUG_PRINT(3, ("Mali PM: Runtime suspend\n"));
+
+	mali_pm_exec_lock();
+
+	/*
+	 * Put SW state directly into "off" state, and do not bother to power
+	 * down each power domain, because entire GPU will be powered off
+	 * when we return.
+	 * For runtime PM suspend, in contrast to OS suspend, there is a race
+	 * between this function and the mali_pm_update_sync_internal(), which
+	 * is fine...
+	 */
+	ret = mali_pm_common_suspend();
+	if (MALI_TRUE == ret) {
+		mali_pm_runtime_active = MALI_FALSE;
+	} else {
+		/*
+		 * Process the "power up" instead,
+		 * which could have been "lost"
+		 */
+		mali_pm_update_sync_internal();
+	}
+
+	mali_pm_exec_unlock();
+
+	return ret;
+}
+
+void mali_pm_runtime_resume(void)
+{
+	struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+
+	mali_pm_exec_lock();
+
+	mali_pm_runtime_active = MALI_TRUE;
+
+#if defined(DEBUG)
+	++num_pm_runtime_resume;
+
+	mali_pm_state_lock();
+
+	/*
+	 * Assert that things are as we left them in runtime_suspend(),
+	 * except for pd_mask_wanted which normally will be the reason we
+	 * got here (job queued => domains wanted)
+	 */
+	MALI_DEBUG_ASSERT(0 == pd_mask_current);
+	MALI_DEBUG_ASSERT(0 == pmu_mask_current);
+
+	mali_pm_state_unlock();
+#endif
+
+	if (NULL != pmu) {
+		mali_pmu_reset(pmu);
+		pmu_mask_current = mali_pmu_get_mask(pmu);
+		MALI_DEBUG_PRINT(3, ("Mali PM: Runtime resume 0x%x \n", pmu_mask_current));
+	}
+
+	/*
+	 * Normally we are resumed because a job has just been queued.
+	 * pd_mask_wanted should thus be != 0.
+	 * It is however possible for others to take a Mali Runtime PM ref
+	 * without having a job queued.
+	 * We should however always call mali_pm_update_sync_internal(),
+	 * because this will take care of any potential mismatch between
+	 * pmu_mask_current and pd_mask_current.
+	 */
+	mali_pm_update_sync_internal();
+
+	mali_pm_exec_unlock();
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_pm_dump_state_domain(struct mali_pm_domain *domain,
+			      char *buf, u32 size)
+{
+	int n = 0;
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tPower domain: id %u\n",
+				mali_pm_domain_get_id(domain));
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\t\tMask: 0x%04x\n",
+				mali_pm_domain_get_mask(domain));
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\t\tUse count: %u\n",
+				mali_pm_domain_get_use_count(domain));
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\t\tCurrent power state: %s\n",
+				(mali_pm_domain_get_mask(domain) & pd_mask_current) ?
+				"On" : "Off");
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\t\tWanted power state: %s\n",
+				(mali_pm_domain_get_mask(domain) & pd_mask_wanted) ?
+				"On" : "Off");
+
+	return n;
+}
+#endif
+
+static void mali_pm_state_lock(void)
+{
+	_mali_osk_spinlock_irq_lock(pm_lock_state);
+}
+
+static void mali_pm_state_unlock(void)
+{
+	_mali_osk_spinlock_irq_unlock(pm_lock_state);
+}
+
+void mali_pm_exec_lock(void)
+{
+	_mali_osk_mutex_wait(pm_lock_exec);
+}
+
+void mali_pm_exec_unlock(void)
+{
+	_mali_osk_mutex_signal(pm_lock_exec);
+}
+
+static void mali_pm_domain_power_up(u32 power_up_mask,
+				    struct mali_group *groups_up[MALI_MAX_NUMBER_OF_GROUPS],
+				    u32 *num_groups_up,
+				    struct mali_l2_cache_core *l2_up[MALI_MAX_NUMBER_OF_L2_CACHE_CORES],
+				    u32 *num_l2_up)
+{
+	u32 domain_bit;
+	u32 notify_mask = power_up_mask;
+
+	MALI_DEBUG_ASSERT(0 != power_up_mask);
+	MALI_DEBUG_ASSERT_POINTER(groups_up);
+	MALI_DEBUG_ASSERT_POINTER(num_groups_up);
+	MALI_DEBUG_ASSERT(0 == *num_groups_up);
+	MALI_DEBUG_ASSERT_POINTER(l2_up);
+	MALI_DEBUG_ASSERT_POINTER(num_l2_up);
+	MALI_DEBUG_ASSERT(0 == *num_l2_up);
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_exec);
+	MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_state);
+
+	MALI_DEBUG_PRINT(5,
+			 ("PM update:      Powering up domains: . [%s]\n",
+			  mali_pm_mask_to_string(power_up_mask)));
+
+	pd_mask_current |= power_up_mask;
+
+	domain_bit = _mali_osk_fls(notify_mask);
+	while (0 != domain_bit) {
+		u32 domain_id = domain_bit - 1;
+		struct mali_pm_domain *domain =
+			mali_pm_domain_get_from_index(
+				domain_id);
+		struct mali_l2_cache_core *l2_cache;
+		struct mali_l2_cache_core *l2_cache_tmp;
+		struct mali_group *group;
+		struct mali_group *group_tmp;
+
+		/* Mark domain as powered up */
+		mali_pm_domain_set_power_on(domain, MALI_TRUE);
+
+		/*
+		 * Make a note of the L2 and/or group(s) to notify
+		 * (need to release the PM state lock before doing so)
+		 */
+
+		_MALI_OSK_LIST_FOREACHENTRY(l2_cache,
+					    l2_cache_tmp,
+					    mali_pm_domain_get_l2_cache_list(
+						    domain),
+					    struct mali_l2_cache_core,
+					    pm_domain_list) {
+			MALI_DEBUG_ASSERT(*num_l2_up <
+					  MALI_MAX_NUMBER_OF_L2_CACHE_CORES);
+			l2_up[*num_l2_up] = l2_cache;
+			(*num_l2_up)++;
+		}
+
+		_MALI_OSK_LIST_FOREACHENTRY(group,
+					    group_tmp,
+					    mali_pm_domain_get_group_list(domain),
+					    struct mali_group,
+					    pm_domain_list) {
+			MALI_DEBUG_ASSERT(*num_groups_up <
+					  MALI_MAX_NUMBER_OF_GROUPS);
+			groups_up[*num_groups_up] = group;
+
+			(*num_groups_up)++;
+		}
+
+		/* Remove current bit and find next */
+		notify_mask &= ~(1 << (domain_id));
+		domain_bit = _mali_osk_fls(notify_mask);
+	}
+}
+static void mali_pm_domain_power_down(u32 power_down_mask,
+				      struct mali_group *groups_down[MALI_MAX_NUMBER_OF_GROUPS],
+				      u32 *num_groups_down,
+				      struct mali_l2_cache_core *l2_down[MALI_MAX_NUMBER_OF_L2_CACHE_CORES],
+				      u32 *num_l2_down)
+{
+	u32 domain_bit;
+	u32 notify_mask = power_down_mask;
+
+	MALI_DEBUG_ASSERT(0 != power_down_mask);
+	MALI_DEBUG_ASSERT_POINTER(groups_down);
+	MALI_DEBUG_ASSERT_POINTER(num_groups_down);
+	MALI_DEBUG_ASSERT(0 == *num_groups_down);
+	MALI_DEBUG_ASSERT_POINTER(l2_down);
+	MALI_DEBUG_ASSERT_POINTER(num_l2_down);
+	MALI_DEBUG_ASSERT(0 == *num_l2_down);
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_exec);
+	MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_state);
+
+	MALI_DEBUG_PRINT(5,
+			 ("PM update:      Powering down domains: [%s]\n",
+			  mali_pm_mask_to_string(power_down_mask)));
+
+	pd_mask_current &= ~power_down_mask;
+
+	domain_bit = _mali_osk_fls(notify_mask);
+	while (0 != domain_bit) {
+		u32 domain_id = domain_bit - 1;
+		struct mali_pm_domain *domain =
+			mali_pm_domain_get_from_index(domain_id);
+		struct mali_l2_cache_core *l2_cache;
+		struct mali_l2_cache_core *l2_cache_tmp;
+		struct mali_group *group;
+		struct mali_group *group_tmp;
+
+		/* Mark domain as powered down */
+		mali_pm_domain_set_power_on(domain, MALI_FALSE);
+
+		/*
+		 * Make a note of the L2s and/or groups to notify
+		 * (need to release the PM state lock before doing so)
+		 */
+
+		_MALI_OSK_LIST_FOREACHENTRY(l2_cache,
+					    l2_cache_tmp,
+					    mali_pm_domain_get_l2_cache_list(domain),
+					    struct mali_l2_cache_core,
+					    pm_domain_list) {
+			MALI_DEBUG_ASSERT(*num_l2_down <
+					  MALI_MAX_NUMBER_OF_L2_CACHE_CORES);
+			l2_down[*num_l2_down] = l2_cache;
+			(*num_l2_down)++;
+		}
+
+		_MALI_OSK_LIST_FOREACHENTRY(group,
+					    group_tmp,
+					    mali_pm_domain_get_group_list(domain),
+					    struct mali_group,
+					    pm_domain_list) {
+			MALI_DEBUG_ASSERT(*num_groups_down <
+					  MALI_MAX_NUMBER_OF_GROUPS);
+			groups_down[*num_groups_down] = group;
+			(*num_groups_down)++;
+		}
+
+		/* Remove current bit and find next */
+		notify_mask &= ~(1 << (domain_id));
+		domain_bit = _mali_osk_fls(notify_mask);
+	}
+}
+
+/*
+ * Execute pending power domain changes
+ * pm_lock_exec lock must be taken by caller.
+ */
+static void mali_pm_update_sync_internal(void)
+{
+	/*
+	 * This should only be called in non-atomic context
+	 * (normally as deferred work)
+	 *
+	 * Look at the pending power domain changes, and execute these.
+	 * Make sure group and schedulers are notified about changes.
+	 */
+
+	struct mali_pmu_core *pmu = mali_pmu_get_global_pmu_core();
+
+	u32 power_down_mask;
+	u32 power_up_mask;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_exec);
+
+#if defined(DEBUG)
+	++num_pm_updates;
+#endif
+
+	/* Hold PM state lock while we look at (and obey) the wanted state */
+	mali_pm_state_lock();
+
+	MALI_DEBUG_PRINT(5, ("PM update pre:  Wanted domain mask: .. [%s]\n",
+			     mali_pm_mask_to_string(pd_mask_wanted)));
+	MALI_DEBUG_PRINT(5, ("PM update pre:  Current domain mask: . [%s]\n",
+			     mali_pm_mask_to_string(pd_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM update pre:  Current PMU mask: .... [%s]\n",
+			     mali_pm_mask_to_string(pmu_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM update pre:  Group power stats: ... <%s>\n",
+			     mali_pm_group_stats_to_string()));
+
+	/* Figure out which cores we need to power on */
+	power_up_mask = pd_mask_wanted &
+			(pd_mask_wanted ^ pd_mask_current);
+
+	if (0 != power_up_mask) {
+		u32 power_up_mask_pmu;
+		struct mali_group *groups_up[MALI_MAX_NUMBER_OF_GROUPS];
+		u32 num_groups_up = 0;
+		struct mali_l2_cache_core *
+			l2_up[MALI_MAX_NUMBER_OF_L2_CACHE_CORES];
+		u32 num_l2_up = 0;
+		u32 i;
+
+#if defined(DEBUG)
+		++num_pm_updates_up;
+#endif
+
+		/*
+		 * Make sure dummy/global domain is always included when
+		 * powering up, since this is controlled by runtime PM,
+		 * and device power is on at this stage.
+		 */
+		power_up_mask |= MALI_PM_DOMAIN_DUMMY_MASK;
+
+		/* Power up only real PMU domains */
+		power_up_mask_pmu = power_up_mask & ~MALI_PM_DOMAIN_DUMMY_MASK;
+
+		/* But not those that happen to be powered on already */
+		power_up_mask_pmu &= (power_up_mask ^ pmu_mask_current) &
+				     power_up_mask;
+
+		if (0 != power_up_mask_pmu) {
+			MALI_DEBUG_ASSERT(NULL != pmu);
+			pmu_mask_current |= power_up_mask_pmu;
+			mali_pmu_power_up(pmu, power_up_mask_pmu);
+		}
+
+		/*
+		 * Put the domains themselves in power up state.
+		 * We get the groups and L2s to notify in return.
+		 */
+		mali_pm_domain_power_up(power_up_mask,
+					groups_up, &num_groups_up,
+					l2_up, &num_l2_up);
+
+		/* Need to unlock PM state lock before notifying L2 + groups */
+		mali_pm_state_unlock();
+
+		/* Notify each L2 cache that we have be powered up */
+		for (i = 0; i < num_l2_up; i++) {
+			mali_l2_cache_power_up(l2_up[i]);
+		}
+
+		/*
+		 * Tell execution module about all the groups we have
+		 * powered up. Groups will be notified as a result of this.
+		 */
+		mali_executor_group_power_up(groups_up, num_groups_up);
+
+		/* Lock state again before checking for power down */
+		mali_pm_state_lock();
+	}
+
+	/* Figure out which cores we need to power off */
+	power_down_mask = pd_mask_current &
+			  (pd_mask_wanted ^ pd_mask_current);
+
+	/*
+	 * Never power down the dummy/global domain here. This is to be done
+	 * from a suspend request (since this domain is only physicall powered
+	 * down at that point)
+	 */
+	power_down_mask &= ~MALI_PM_DOMAIN_DUMMY_MASK;
+
+	if (0 != power_down_mask) {
+		u32 power_down_mask_pmu;
+		struct mali_group *groups_down[MALI_MAX_NUMBER_OF_GROUPS];
+		u32 num_groups_down = 0;
+		struct mali_l2_cache_core *
+			l2_down[MALI_MAX_NUMBER_OF_L2_CACHE_CORES];
+		u32 num_l2_down = 0;
+		u32 i;
+
+#if defined(DEBUG)
+		++num_pm_updates_down;
+#endif
+
+		/*
+		 * Put the domains themselves in power down state.
+		 * We get the groups and L2s to notify in return.
+		 */
+		mali_pm_domain_power_down(power_down_mask,
+					  groups_down, &num_groups_down,
+					  l2_down, &num_l2_down);
+
+		/* Need to unlock PM state lock before notifying L2 + groups */
+		mali_pm_state_unlock();
+
+		/*
+		 * Tell execution module about all the groups we will be
+		 * powering down. Groups will be notified as a result of this.
+		 */
+		if (0 < num_groups_down) {
+			mali_executor_group_power_down(groups_down, num_groups_down);
+		}
+
+		/* Notify each L2 cache that we will be powering down */
+		for (i = 0; i < num_l2_down; i++) {
+			mali_l2_cache_power_down(l2_down[i]);
+		}
+
+		/*
+		 * Power down only PMU domains which should not stay on
+		 * Some domains might for instance currently be incorrectly
+		 * powered up if default domain power state is all on.
+		 */
+		power_down_mask_pmu = pmu_mask_current & (~pd_mask_current);
+
+		if (0 != power_down_mask_pmu) {
+			MALI_DEBUG_ASSERT(NULL != pmu);
+			pmu_mask_current &= ~power_down_mask_pmu;
+			mali_pmu_power_down(pmu, power_down_mask_pmu);
+
+		}
+	} else {
+		/*
+		 * Power down only PMU domains which should not stay on
+		 * Some domains might for instance currently be incorrectly
+		 * powered up if default domain power state is all on.
+		 */
+		u32 power_down_mask_pmu;
+
+		/* No need for state lock since we'll only update PMU */
+		mali_pm_state_unlock();
+
+		power_down_mask_pmu = pmu_mask_current & (~pd_mask_current);
+
+		if (0 != power_down_mask_pmu) {
+			MALI_DEBUG_ASSERT(NULL != pmu);
+			pmu_mask_current &= ~power_down_mask_pmu;
+			mali_pmu_power_down(pmu, power_down_mask_pmu);
+		}
+	}
+
+	MALI_DEBUG_PRINT(5, ("PM update post: Current domain mask: . [%s]\n",
+			     mali_pm_mask_to_string(pd_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM update post: Current PMU mask: .... [%s]\n",
+			     mali_pm_mask_to_string(pmu_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM update post: Group power stats: ... <%s>\n",
+			     mali_pm_group_stats_to_string()));
+}
+
+static mali_bool mali_pm_common_suspend(void)
+{
+	mali_pm_state_lock();
+
+	if (0 != pd_mask_wanted) {
+		MALI_DEBUG_PRINT(5, ("PM: Aborting suspend operation\n\n\n"));
+		mali_pm_state_unlock();
+		return MALI_FALSE;
+	}
+
+	MALI_DEBUG_PRINT(5, ("PM suspend pre: Wanted domain mask: .. [%s]\n",
+			     mali_pm_mask_to_string(pd_mask_wanted)));
+	MALI_DEBUG_PRINT(5, ("PM suspend pre: Current domain mask: . [%s]\n",
+			     mali_pm_mask_to_string(pd_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM suspend pre: Current PMU mask: .... [%s]\n",
+			     mali_pm_mask_to_string(pmu_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM suspend pre: Group power stats: ... <%s>\n",
+			     mali_pm_group_stats_to_string()));
+
+	if (0 != pd_mask_current) {
+		/*
+		 * We have still some domains powered on.
+		 * It is for instance very normal that at least the
+		 * dummy/global domain is marked as powered on at this point.
+		 * (because it is physically powered on until this function
+		 * returns)
+		 */
+
+		struct mali_group *groups_down[MALI_MAX_NUMBER_OF_GROUPS];
+		u32 num_groups_down = 0;
+		struct mali_l2_cache_core *
+			l2_down[MALI_MAX_NUMBER_OF_L2_CACHE_CORES];
+		u32 num_l2_down = 0;
+		u32 i;
+
+		/*
+		 * Put the domains themselves in power down state.
+		 * We get the groups and L2s to notify in return.
+		 */
+		mali_pm_domain_power_down(pd_mask_current,
+					  groups_down,
+					  &num_groups_down,
+					  l2_down,
+					  &num_l2_down);
+
+		MALI_DEBUG_ASSERT(0 == pd_mask_current);
+		MALI_DEBUG_ASSERT(MALI_TRUE == mali_pm_domain_all_unused());
+
+		/* Need to unlock PM state lock before notifying L2 + groups */
+		mali_pm_state_unlock();
+
+		/*
+		 * Tell execution module about all the groups we will be
+		 * powering down. Groups will be notified as a result of this.
+		 */
+		if (0 < num_groups_down) {
+			mali_executor_group_power_down(groups_down, num_groups_down);
+		}
+
+		/* Notify each L2 cache that we will be powering down */
+		for (i = 0; i < num_l2_down; i++) {
+			mali_l2_cache_power_down(l2_down[i]);
+		}
+
+		pmu_mask_current = 0;
+	} else {
+		MALI_DEBUG_ASSERT(0 == pmu_mask_current);
+
+		MALI_DEBUG_ASSERT(MALI_TRUE == mali_pm_domain_all_unused());
+
+		mali_pm_state_unlock();
+	}
+
+	MALI_DEBUG_PRINT(5, ("PM suspend post: Current domain mask:  [%s]\n",
+			     mali_pm_mask_to_string(pd_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM suspend post: Current PMU mask: ... [%s]\n",
+			     mali_pm_mask_to_string(pmu_mask_current)));
+	MALI_DEBUG_PRINT(5, ("PM suspend post: Group power stats: .. <%s>\n",
+			     mali_pm_group_stats_to_string()));
+
+	return MALI_TRUE;
+}
+
+static void mali_pm_update_work(void *data)
+{
+	MALI_IGNORE(data);
+	mali_pm_update_sync();
+}
+
+static _mali_osk_errcode_t mali_pm_create_pm_domains(void)
+{
+	int i;
+
+	/* Create all domains (including dummy domain) */
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		if (0x0 == domain_config[i]) continue;
+
+		if (NULL == mali_pm_domain_create(domain_config[i])) {
+			return _MALI_OSK_ERR_NOMEM;
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static void mali_pm_set_default_pm_domain_config(void)
+{
+	MALI_DEBUG_ASSERT(0 != _mali_osk_resource_base_address());
+
+	/* GP core */
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_GP, NULL)) {
+		domain_config[MALI_DOMAIN_INDEX_GP] = 0x01;
+	}
+
+	/* PP0 - PP3 core */
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP0, NULL)) {
+		if (mali_is_mali400()) {
+			domain_config[MALI_DOMAIN_INDEX_PP0] = 0x01 << 2;
+		} else if (mali_is_mali450()) {
+			domain_config[MALI_DOMAIN_INDEX_PP0] = 0x01 << 1;
+		} else if (mali_is_mali470()) {
+			domain_config[MALI_DOMAIN_INDEX_PP0] = 0x01 << 0;
+		}
+	}
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP1, NULL)) {
+		if (mali_is_mali400()) {
+			domain_config[MALI_DOMAIN_INDEX_PP1] = 0x01 << 3;
+		} else if (mali_is_mali450()) {
+			domain_config[MALI_DOMAIN_INDEX_PP1] = 0x01 << 2;
+		} else if (mali_is_mali470()) {
+			domain_config[MALI_DOMAIN_INDEX_PP1] = 0x01 << 1;
+		}
+	}
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP2, NULL)) {
+		if (mali_is_mali400()) {
+			domain_config[MALI_DOMAIN_INDEX_PP2] = 0x01 << 4;
+		} else if (mali_is_mali450()) {
+			domain_config[MALI_DOMAIN_INDEX_PP2] = 0x01 << 2;
+		} else if (mali_is_mali470()) {
+			domain_config[MALI_DOMAIN_INDEX_PP2] = 0x01 << 1;
+		}
+	}
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP3, NULL)) {
+		if (mali_is_mali400()) {
+			domain_config[MALI_DOMAIN_INDEX_PP3] = 0x01 << 5;
+		} else if (mali_is_mali450()) {
+			domain_config[MALI_DOMAIN_INDEX_PP3] = 0x01 << 2;
+		} else if (mali_is_mali470()) {
+			domain_config[MALI_DOMAIN_INDEX_PP3] = 0x01 << 1;
+		}
+	}
+
+	/* PP4 - PP7 */
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP4, NULL)) {
+		domain_config[MALI_DOMAIN_INDEX_PP4] = 0x01 << 3;
+	}
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP5, NULL)) {
+		domain_config[MALI_DOMAIN_INDEX_PP5] = 0x01 << 3;
+	}
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP6, NULL)) {
+		domain_config[MALI_DOMAIN_INDEX_PP6] = 0x01 << 3;
+	}
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+		    MALI_OFFSET_PP7, NULL)) {
+		domain_config[MALI_DOMAIN_INDEX_PP7] = 0x01 << 3;
+	}
+
+	/* L2gp/L2PP0/L2PP4 */
+	if (mali_is_mali400()) {
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+			    MALI400_OFFSET_L2_CACHE0, NULL)) {
+			domain_config[MALI_DOMAIN_INDEX_L20] = 0x01 << 1;
+		}
+	} else if (mali_is_mali450()) {
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+			    MALI450_OFFSET_L2_CACHE0, NULL)) {
+			domain_config[MALI_DOMAIN_INDEX_L20] = 0x01 << 0;
+		}
+
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+			    MALI450_OFFSET_L2_CACHE1, NULL)) {
+			domain_config[MALI_DOMAIN_INDEX_L21] = 0x01 << 1;
+		}
+
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+			    MALI450_OFFSET_L2_CACHE2, NULL)) {
+			domain_config[MALI_DOMAIN_INDEX_L22] = 0x01 << 3;
+		}
+	} else if (mali_is_mali470()) {
+		if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(
+			    MALI470_OFFSET_L2_CACHE1, NULL)) {
+			domain_config[MALI_DOMAIN_INDEX_L21] = 0x01 << 0;
+		}
+	}
+}
+
+static u32 mali_pm_get_registered_cores_mask(void)
+{
+	int i = 0;
+	u32 mask = 0;
+
+	for (i = 0; i < MALI_DOMAIN_INDEX_DUMMY; i++) {
+		mask |= domain_config[i];
+	}
+
+	return mask;
+}
+
+static void mali_pm_set_pmu_domain_config(void)
+{
+	int i = 0;
+
+	_mali_osk_device_data_pmu_config_get(domain_config, MALI_MAX_NUMBER_OF_DOMAINS - 1);
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS - 1; i++) {
+		if (0 != domain_config[i]) {
+			MALI_DEBUG_PRINT(2, ("Using customer pmu config:\n"));
+			break;
+		}
+	}
+
+	if (MALI_MAX_NUMBER_OF_DOMAINS - 1 == i) {
+		MALI_DEBUG_PRINT(2, ("Using hw detect pmu config:\n"));
+		mali_pm_set_default_pm_domain_config();
+	}
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS - 1; i++) {
+		if (domain_config[i]) {
+			MALI_DEBUG_PRINT(2, ("domain_config[%d] = 0x%x \n", i, domain_config[i]));
+		}
+	}
+	/* Can't override dummy domain mask */
+	domain_config[MALI_DOMAIN_INDEX_DUMMY] =
+		1 << MALI_DOMAIN_INDEX_DUMMY;
+}
+
+#if defined(DEBUG)
+const char *mali_pm_mask_to_string(u32 mask)
+{
+	static char bit_str[MALI_MAX_NUMBER_OF_DOMAINS + 1];
+	int bit;
+	int str_pos = 0;
+
+	/* Must be protected by lock since we use shared string buffer */
+	if (NULL != pm_lock_exec) {
+		MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_exec);
+	}
+
+	for (bit = MALI_MAX_NUMBER_OF_DOMAINS - 1; bit >= 0; bit--) {
+		if (mask & (1 << bit)) {
+			bit_str[str_pos] = 'X';
+		} else {
+			bit_str[str_pos] = '-';
+		}
+		str_pos++;
+	}
+
+	bit_str[MALI_MAX_NUMBER_OF_DOMAINS] = '\0';
+
+	return bit_str;
+}
+
+const char *mali_pm_group_stats_to_string(void)
+{
+	static char bit_str[MALI_MAX_NUMBER_OF_GROUPS + 1];
+	u32 num_groups = mali_group_get_glob_num_groups();
+	u32 i;
+
+	/* Must be protected by lock since we use shared string buffer */
+	if (NULL != pm_lock_exec) {
+		MALI_DEBUG_ASSERT_LOCK_HELD(pm_lock_exec);
+	}
+
+	for (i = 0; i < num_groups && i < MALI_MAX_NUMBER_OF_GROUPS; i++) {
+		struct mali_group *group;
+
+		group = mali_group_get_glob_group(i);
+
+		if (MALI_TRUE == mali_group_power_is_on(group)) {
+			bit_str[i] = 'X';
+		} else {
+			bit_str[i] = '-';
+		}
+	}
+
+	bit_str[i] = '\0';
+
+	return bit_str;
+}
+#endif
+
+/*
+ * num_pp is the number of PP cores which will be powered on given this mask
+ * cost is the total power cost of cores which will be powered on given this mask
+ */
+static void mali_pm_stat_from_mask(u32 mask, u32 *num_pp, u32 *cost)
+{
+	u32 i;
+
+	/* loop through all cores */
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		if (!(domain_config[i] & mask)) {
+			continue;
+		}
+
+		switch (i) {
+		case MALI_DOMAIN_INDEX_GP:
+			*cost += MALI_GP_COST;
+
+			break;
+		case MALI_DOMAIN_INDEX_PP0: /* Fall through */
+		case MALI_DOMAIN_INDEX_PP1: /* Fall through */
+		case MALI_DOMAIN_INDEX_PP2: /* Fall through */
+		case MALI_DOMAIN_INDEX_PP3:
+			if (mali_is_mali400()) {
+				if ((domain_config[MALI_DOMAIN_INDEX_L20] & mask)
+				    || (domain_config[MALI_DOMAIN_INDEX_DUMMY]
+					== domain_config[MALI_DOMAIN_INDEX_L20])) {
+					*num_pp += 1;
+				}
+			} else {
+				if ((domain_config[MALI_DOMAIN_INDEX_L21] & mask)
+				    || (domain_config[MALI_DOMAIN_INDEX_DUMMY]
+					== domain_config[MALI_DOMAIN_INDEX_L21])) {
+					*num_pp += 1;
+				}
+			}
+
+			*cost += MALI_PP_COST;
+			break;
+		case MALI_DOMAIN_INDEX_PP4: /* Fall through */
+		case MALI_DOMAIN_INDEX_PP5: /* Fall through */
+		case MALI_DOMAIN_INDEX_PP6: /* Fall through */
+		case MALI_DOMAIN_INDEX_PP7:
+			MALI_DEBUG_ASSERT(mali_is_mali450());
+
+			if ((domain_config[MALI_DOMAIN_INDEX_L22] & mask)
+			    || (domain_config[MALI_DOMAIN_INDEX_DUMMY]
+				== domain_config[MALI_DOMAIN_INDEX_L22])) {
+				*num_pp += 1;
+			}
+
+			*cost += MALI_PP_COST;
+			break;
+		case MALI_DOMAIN_INDEX_L20: /* Fall through */
+		case MALI_DOMAIN_INDEX_L21: /* Fall through */
+		case MALI_DOMAIN_INDEX_L22:
+			*cost += MALI_L2_COST;
+
+			break;
+		}
+	}
+}
+
+void mali_pm_power_cost_setup(void)
+{
+	/*
+	 * Two parallel arrays which store the best domain mask and its cost
+	 * The index is the number of PP cores, E.g. Index 0 is for 1 PP option,
+	 * might have mask 0x2 and with cost of 1, lower cost is better
+	 */
+	u32 best_mask[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS] = { 0 };
+	u32 best_cost[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS] = { 0 };
+	/* Array cores_in_domain is used to store the total pp cores in each pm domain. */
+	u32 cores_in_domain[MALI_MAX_NUMBER_OF_DOMAINS] = { 0 };
+	/* Domain_count is used to represent the max domain we have.*/
+	u32 max_domain_mask = 0;
+	u32 max_domain_id = 0;
+	u32 always_on_pp_cores = 0;
+
+	u32 num_pp, cost, mask;
+	u32 i, j , k;
+
+	/* Initialize statistics */
+	for (i = 0; i < MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS; i++) {
+		best_mask[i] = 0;
+		best_cost[i] = 0xFFFFFFFF; /* lower cost is better */
+	}
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS + 1; i++) {
+		for (j = 0; j < MALI_MAX_NUMBER_OF_DOMAINS; j++) {
+			mali_pm_domain_power_cost_result[i][j] = 0;
+		}
+	}
+
+	/* Caculate number of pp cores of a given domain config. */
+	for (i = MALI_DOMAIN_INDEX_PP0; i <= MALI_DOMAIN_INDEX_PP7; i++) {
+		if (0 < domain_config[i]) {
+			/* Get the max domain mask value used to caculate power cost
+			 * and we don't count in always on pp cores. */
+			if (MALI_PM_DOMAIN_DUMMY_MASK != domain_config[i]
+			    && max_domain_mask < domain_config[i]) {
+				max_domain_mask = domain_config[i];
+			}
+
+			if (MALI_PM_DOMAIN_DUMMY_MASK == domain_config[i]) {
+				always_on_pp_cores++;
+			}
+		}
+	}
+	max_domain_id = _mali_osk_fls(max_domain_mask);
+
+	/*
+	 * Try all combinations of power domains and check how many PP cores
+	 * they have and their power cost.
+	 */
+	for (mask = 0; mask < (1 << max_domain_id); mask++) {
+		num_pp = 0;
+		cost = 0;
+
+		mali_pm_stat_from_mask(mask, &num_pp, &cost);
+
+		/* This mask is usable for all MP1 up to num_pp PP cores, check statistics for all */
+		for (i = 0; i < num_pp; i++) {
+			if (best_cost[i] >= cost) {
+				best_cost[i] = cost;
+				best_mask[i] = mask;
+			}
+		}
+	}
+
+	/*
+	 * If we want to enable x pp cores, if x is less than number of always_on pp cores,
+	 * all of pp cores we will enable must be always_on pp cores.
+	 */
+	for (i = 0; i < mali_executor_get_num_cores_total(); i++) {
+		if (i < always_on_pp_cores) {
+			mali_pm_domain_power_cost_result[i + 1][MALI_MAX_NUMBER_OF_DOMAINS - 1]
+				= i + 1;
+		} else {
+			mali_pm_domain_power_cost_result[i + 1][MALI_MAX_NUMBER_OF_DOMAINS - 1]
+				= always_on_pp_cores;
+		}
+	}
+
+	/* In this loop, variable i represent for the number of non-always on pp cores we want to enabled. */
+	for (i = 0; i < (mali_executor_get_num_cores_total() - always_on_pp_cores); i++) {
+		if (best_mask[i] == 0) {
+			/* This MP variant is not available */
+			continue;
+		}
+
+		for (j = 0; j < MALI_MAX_NUMBER_OF_DOMAINS; j++) {
+			cores_in_domain[j] = 0;
+		}
+
+		for (j = MALI_DOMAIN_INDEX_PP0; j <= MALI_DOMAIN_INDEX_PP7; j++) {
+			if (0 < domain_config[j]
+			    && (MALI_PM_DOMAIN_DUMMY_MASK != domain_config[i])) {
+				cores_in_domain[_mali_osk_fls(domain_config[j]) - 1]++;
+			}
+		}
+
+		/* In this loop, j represent for the number we have already enabled.*/
+		for (j = 0; j <= i;) {
+			/* j used to visit all of domain to get the number of pp cores remained in it. */
+			for (k = 0; k < max_domain_id; k++) {
+				/* If domain k in best_mask[i] is enabled and this domain has extra pp cores,
+				 * we know we must pick at least one pp core from this domain.
+				 * And then we move to next enabled pm domain. */
+				if ((best_mask[i] & (0x1 << k)) && (0 < cores_in_domain[k])) {
+					cores_in_domain[k]--;
+					mali_pm_domain_power_cost_result[always_on_pp_cores + i + 1][k]++;
+					j++;
+					if (j > i) {
+						break;
+					}
+				}
+			}
+		}
+	}
+}
+
+/*
+ * When we are doing core scaling,
+ * this function is called to return the best mask to
+ * achieve the best pp group power cost.
+ */
+void mali_pm_get_best_power_cost_mask(int num_requested, int *dst)
+{
+	MALI_DEBUG_ASSERT((mali_executor_get_num_cores_total() >= num_requested) && (0 <= num_requested));
+
+	_mali_osk_memcpy(dst, mali_pm_domain_power_cost_result[num_requested], MALI_MAX_NUMBER_OF_DOMAINS * sizeof(int));
+}
+
+u32 mali_pm_get_current_mask(void)
+{
+	return pd_mask_current;
+}
+
+u32 mali_pm_get_wanted_mask(void)
+{
+	return pd_mask_wanted;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pm.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pm.h
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PM_H__
+#define __MALI_PM_H__
+
+#include "mali_osk.h"
+#include "mali_pm_domain.h"
+
+#define MALI_DOMAIN_INDEX_GP        0
+#define MALI_DOMAIN_INDEX_PP0       1
+#define MALI_DOMAIN_INDEX_PP1       2
+#define MALI_DOMAIN_INDEX_PP2       3
+#define MALI_DOMAIN_INDEX_PP3       4
+#define MALI_DOMAIN_INDEX_PP4       5
+#define MALI_DOMAIN_INDEX_PP5       6
+#define MALI_DOMAIN_INDEX_PP6       7
+#define MALI_DOMAIN_INDEX_PP7       8
+#define MALI_DOMAIN_INDEX_L20       9
+#define MALI_DOMAIN_INDEX_L21      10
+#define MALI_DOMAIN_INDEX_L22      11
+/*
+ * The dummy domain is used when there is no physical power domain
+ * (e.g. no PMU or always on cores)
+ */
+#define MALI_DOMAIN_INDEX_DUMMY    12
+#define MALI_MAX_NUMBER_OF_DOMAINS 13
+
+/**
+ * Initialize the Mali PM module
+ *
+ * PM module covers Mali PM core, PM domains and Mali PMU
+ */
+_mali_osk_errcode_t mali_pm_initialize(void);
+
+/**
+ * Terminate the Mali PM module
+ */
+void mali_pm_terminate(void);
+
+void mali_pm_exec_lock(void);
+void mali_pm_exec_unlock(void);
+
+
+struct mali_pm_domain *mali_pm_register_l2_cache(u32 domain_index,
+		struct mali_l2_cache_core *l2_cache);
+struct mali_pm_domain *mali_pm_register_group(u32 domain_index,
+		struct mali_group *group);
+
+mali_bool mali_pm_get_domain_refs(struct mali_pm_domain **domains,
+				  struct mali_group **groups,
+				  u32 num_domains);
+mali_bool mali_pm_put_domain_refs(struct mali_pm_domain **domains,
+				  u32 num_domains);
+
+void mali_pm_init_begin(void);
+void mali_pm_init_end(void);
+
+void mali_pm_update_sync(void);
+void mali_pm_update_async(void);
+
+/* Callback functions for system power management */
+void mali_pm_os_suspend(mali_bool os_suspend);
+void mali_pm_os_resume(void);
+
+mali_bool mali_pm_runtime_suspend(void);
+void mali_pm_runtime_resume(void);
+
+#if MALI_STATE_TRACKING
+u32 mali_pm_dump_state_domain(struct mali_pm_domain *domain,
+			      char *buf, u32 size);
+#endif
+
+void mali_pm_power_cost_setup(void);
+
+void mali_pm_get_best_power_cost_mask(int num_requested, int *dst);
+
+#if defined(DEBUG)
+const char *mali_pm_mask_to_string(u32 mask);
+#endif
+
+u32 mali_pm_get_current_mask(void);
+u32 mali_pm_get_wanted_mask(void);
+#endif /* __MALI_PM_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pm_domain.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pm_domain.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright (C) 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_pm_domain.h"
+#include "mali_pmu.h"
+#include "mali_group.h"
+#include "mali_pm.h"
+
+static struct mali_pm_domain *mali_pm_domains[MALI_MAX_NUMBER_OF_DOMAINS] =
+{ NULL, };
+
+void mali_pm_domain_initialize(void)
+{
+	/* Domains will be initialized/created on demand */
+}
+
+void mali_pm_domain_terminate(void)
+{
+	int i;
+
+	/* Delete all domains that has been created */
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		mali_pm_domain_delete(mali_pm_domains[i]);
+		mali_pm_domains[i] = NULL;
+	}
+}
+
+struct mali_pm_domain *mali_pm_domain_create(u32 pmu_mask)
+{
+	struct mali_pm_domain *domain = NULL;
+	u32 domain_id = 0;
+
+	domain = mali_pm_domain_get_from_mask(pmu_mask);
+	if (NULL != domain) return domain;
+
+	MALI_DEBUG_PRINT(2,
+			 ("Mali PM domain: Creating Mali PM domain (mask=0x%08X)\n",
+			  pmu_mask));
+
+	domain = (struct mali_pm_domain *)_mali_osk_malloc(
+			 sizeof(struct mali_pm_domain));
+	if (NULL != domain) {
+		domain->power_is_on = MALI_FALSE;
+		domain->pmu_mask = pmu_mask;
+		domain->use_count = 0;
+		_mali_osk_list_init(&domain->group_list);
+		_mali_osk_list_init(&domain->l2_cache_list);
+
+		domain_id = _mali_osk_fls(pmu_mask) - 1;
+		/* Verify the domain_id */
+		MALI_DEBUG_ASSERT(MALI_MAX_NUMBER_OF_DOMAINS > domain_id);
+		/* Verify that pmu_mask only one bit is set */
+		MALI_DEBUG_ASSERT((1 << domain_id) == pmu_mask);
+		mali_pm_domains[domain_id] = domain;
+
+		return domain;
+	} else {
+		MALI_DEBUG_PRINT_ERROR(("Unable to create PM domain\n"));
+	}
+
+	return NULL;
+}
+
+void mali_pm_domain_delete(struct mali_pm_domain *domain)
+{
+	if (NULL == domain) {
+		return;
+	}
+
+	_mali_osk_list_delinit(&domain->group_list);
+	_mali_osk_list_delinit(&domain->l2_cache_list);
+
+	_mali_osk_free(domain);
+}
+
+void mali_pm_domain_add_group(struct mali_pm_domain *domain,
+			      struct mali_group *group)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	/*
+	 * Use addtail because virtual group is created last and it needs
+	 * to be at the end of the list (in order to be activated after
+	 * all children.
+	 */
+	_mali_osk_list_addtail(&group->pm_domain_list, &domain->group_list);
+}
+
+void mali_pm_domain_add_l2_cache(struct mali_pm_domain *domain,
+				 struct mali_l2_cache_core *l2_cache)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	MALI_DEBUG_ASSERT_POINTER(l2_cache);
+	_mali_osk_list_add(&l2_cache->pm_domain_list, &domain->l2_cache_list);
+}
+
+struct mali_pm_domain *mali_pm_domain_get_from_mask(u32 mask)
+{
+	u32 id = 0;
+
+	if (0 == mask) {
+		return NULL;
+	}
+
+	id = _mali_osk_fls(mask) - 1;
+
+	MALI_DEBUG_ASSERT(MALI_MAX_NUMBER_OF_DOMAINS > id);
+	/* Verify that pmu_mask only one bit is set */
+	MALI_DEBUG_ASSERT((1 << id) == mask);
+
+	return mali_pm_domains[id];
+}
+
+struct mali_pm_domain *mali_pm_domain_get_from_index(u32 id)
+{
+	MALI_DEBUG_ASSERT(MALI_MAX_NUMBER_OF_DOMAINS > id);
+
+	return mali_pm_domains[id];
+}
+
+u32 mali_pm_domain_ref_get(struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+
+	if (0 == domain->use_count) {
+		_mali_osk_pm_dev_ref_get_async();
+	}
+
+	++domain->use_count;
+	MALI_DEBUG_PRINT(4, ("PM domain %p: ref_get, use_count => %u\n", domain, domain->use_count));
+
+	/* Return our mask so caller can check this against wanted mask */
+	return domain->pmu_mask;
+}
+
+u32 mali_pm_domain_ref_put(struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+
+	--domain->use_count;
+	MALI_DEBUG_PRINT(4, ("PM domain %p: ref_put, use_count => %u\n", domain, domain->use_count));
+
+	if (0 == domain->use_count) {
+		_mali_osk_pm_dev_ref_put();
+	}
+
+	/*
+	 * Return the PMU mask which now could be be powered down
+	 * (the bit for this domain).
+	 * This is the responsibility of the caller (mali_pm)
+	 */
+	return (0 == domain->use_count ? domain->pmu_mask : 0);
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_pm_domain_get_id(struct mali_pm_domain *domain)
+{
+	u32 id = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	MALI_DEBUG_ASSERT(0 != domain->pmu_mask);
+
+	id = _mali_osk_fls(domain->pmu_mask) - 1;
+
+	MALI_DEBUG_ASSERT(MALI_MAX_NUMBER_OF_DOMAINS > id);
+	/* Verify that pmu_mask only one bit is set */
+	MALI_DEBUG_ASSERT((1 << id) == domain->pmu_mask);
+	/* Verify that we have stored the domain at right id/index */
+	MALI_DEBUG_ASSERT(domain == mali_pm_domains[id]);
+
+	return id;
+}
+#endif
+
+#if defined(DEBUG)
+mali_bool mali_pm_domain_all_unused(void)
+{
+	int i;
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_DOMAINS; i++) {
+		if (NULL == mali_pm_domains[i]) {
+			/* Nothing to check */
+			continue;
+		}
+
+		if (MALI_TRUE == mali_pm_domains[i]->power_is_on) {
+			/* Not ready for suspend! */
+			return MALI_FALSE;
+		}
+
+		if (0 != mali_pm_domains[i]->use_count) {
+			/* Not ready for suspend! */
+			return MALI_FALSE;
+		}
+	}
+
+	return MALI_TRUE;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pm_domain.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pm_domain.h
@@ -0,0 +1,104 @@
+/*
+ * Copyright (C) 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PM_DOMAIN_H__
+#define __MALI_PM_DOMAIN_H__
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+
+#include "mali_l2_cache.h"
+#include "mali_group.h"
+#include "mali_pmu.h"
+
+/* Instances are protected by PM state lock */
+struct mali_pm_domain {
+	mali_bool power_is_on;
+	s32 use_count;
+	u32 pmu_mask;
+
+	/* Zero or more groups can belong to this domain */
+	_mali_osk_list_t group_list;
+
+	/* Zero or more L2 caches can belong to this domain */
+	_mali_osk_list_t l2_cache_list;
+};
+
+
+void mali_pm_domain_initialize(void);
+void mali_pm_domain_terminate(void);
+
+struct mali_pm_domain *mali_pm_domain_create(u32 pmu_mask);
+void mali_pm_domain_delete(struct mali_pm_domain *domain);
+
+void mali_pm_domain_add_l2_cache(
+	struct mali_pm_domain *domain,
+	struct mali_l2_cache_core *l2_cache);
+void mali_pm_domain_add_group(struct mali_pm_domain *domain,
+			      struct mali_group *group);
+
+struct mali_pm_domain *mali_pm_domain_get_from_mask(u32 mask);
+struct mali_pm_domain *mali_pm_domain_get_from_index(u32 id);
+
+/* Ref counting */
+u32 mali_pm_domain_ref_get(struct mali_pm_domain *domain);
+u32 mali_pm_domain_ref_put(struct mali_pm_domain *domain);
+
+MALI_STATIC_INLINE _mali_osk_list_t *mali_pm_domain_get_group_list(
+	struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	return &domain->group_list;
+}
+
+MALI_STATIC_INLINE _mali_osk_list_t *mali_pm_domain_get_l2_cache_list(
+	struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	return &domain->l2_cache_list;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pm_domain_power_is_on(
+	struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	return domain->power_is_on;
+}
+
+MALI_STATIC_INLINE void mali_pm_domain_set_power_on(
+	struct mali_pm_domain *domain,
+	mali_bool power_is_on)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	domain->power_is_on = power_is_on;
+}
+
+MALI_STATIC_INLINE u32 mali_pm_domain_get_use_count(
+	struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	return domain->use_count;
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_pm_domain_get_id(struct mali_pm_domain *domain);
+
+MALI_STATIC_INLINE u32 mali_pm_domain_get_mask(struct mali_pm_domain *domain)
+{
+	MALI_DEBUG_ASSERT_POINTER(domain);
+	return domain->pmu_mask;
+}
+#endif
+
+#if defined(DEBUG)
+mali_bool mali_pm_domain_all_unused(void);
+#endif
+
+#endif /* __MALI_PM_DOMAIN_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pm_metrics.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pm_metrics.c
@@ -0,0 +1,255 @@
+/*
+ * Copyright (C) 2010-2014, 2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include "mali_pm_metrics.h"
+#include "mali_osk_locks.h"
+#include "mali_osk_mali.h"
+#include <linux/ktime.h>
+
+#define MALI_PM_TIME_SHIFT 0
+#define MALI_UTILIZATION_MAX_PERIOD 80000000/* ns = 100ms */
+
+_mali_osk_errcode_t mali_pm_metrics_init(struct mali_device *mdev)
+{
+	int i = 0;
+
+	MALI_DEBUG_ASSERT(mdev != NULL);
+
+	mdev->mali_metrics.time_period_start = ktime_get();
+	mdev->mali_metrics.time_period_start_gp = mdev->mali_metrics.time_period_start;
+	mdev->mali_metrics.time_period_start_pp = mdev->mali_metrics.time_period_start;
+
+	mdev->mali_metrics.time_busy = 0;
+	mdev->mali_metrics.time_idle = 0;
+	mdev->mali_metrics.prev_busy = 0;
+	mdev->mali_metrics.prev_idle = 0;
+	mdev->mali_metrics.num_running_gp_cores = 0;
+	mdev->mali_metrics.num_running_pp_cores = 0;
+	mdev->mali_metrics.time_busy_gp = 0;
+	mdev->mali_metrics.time_idle_gp = 0;
+
+	for (i = 0; i < MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS; i++) {
+		mdev->mali_metrics.time_busy_pp[i] = 0;
+		mdev->mali_metrics.time_idle_pp[i] = 0;
+	}
+	mdev->mali_metrics.gpu_active = MALI_FALSE;
+
+	mdev->mali_metrics.lock = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_UNORDERED, _MALI_OSK_LOCK_ORDER_FIRST);
+	if (NULL == mdev->mali_metrics.lock) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_pm_metrics_term(struct mali_device *mdev)
+{
+	_mali_osk_spinlock_irq_term(mdev->mali_metrics.lock);
+}
+
+/*caller needs to hold mdev->mali_metrics.lock before calling this function*/
+void mali_pm_record_job_status(struct mali_device *mdev)
+{
+	ktime_t now;
+	ktime_t diff;
+	u64 ns_time;
+
+	MALI_DEBUG_ASSERT(mdev != NULL);
+
+	now = ktime_get();
+	diff = ktime_sub(now, mdev->mali_metrics.time_period_start);
+
+	ns_time = (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+	mdev->mali_metrics.time_busy += ns_time;
+	mdev->mali_metrics.time_period_start = now;
+}
+
+void mali_pm_record_gpu_idle(mali_bool is_gp)
+{
+	ktime_t now;
+	ktime_t diff;
+	u64 ns_time;
+	struct mali_device *mdev = dev_get_drvdata(&mali_platform_device->dev);
+
+	MALI_DEBUG_ASSERT(mdev != NULL);
+
+	_mali_osk_spinlock_irq_lock(mdev->mali_metrics.lock);
+	now = ktime_get();
+
+	if (MALI_TRUE == is_gp) {
+		--mdev->mali_metrics.num_running_gp_cores;
+		if (0 == mdev->mali_metrics.num_running_gp_cores) {
+			diff = ktime_sub(now, mdev->mali_metrics.time_period_start_gp);
+			ns_time = (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+			mdev->mali_metrics.time_busy_gp += ns_time;
+			mdev->mali_metrics.time_period_start_gp = now;
+
+			if (0 == mdev->mali_metrics.num_running_pp_cores) {
+				MALI_DEBUG_ASSERT(mdev->mali_metrics.gpu_active == MALI_TRUE);
+				diff = ktime_sub(now, mdev->mali_metrics.time_period_start);
+				ns_time = (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+				mdev->mali_metrics.time_busy += ns_time;
+				mdev->mali_metrics.time_period_start = now;
+				mdev->mali_metrics.gpu_active = MALI_FALSE;
+			}
+		}
+	} else {
+		--mdev->mali_metrics.num_running_pp_cores;
+		if (0 == mdev->mali_metrics.num_running_pp_cores) {
+			diff = ktime_sub(now, mdev->mali_metrics.time_period_start_pp);
+			ns_time = (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+			mdev->mali_metrics.time_busy_pp[0] += ns_time;
+			mdev->mali_metrics.time_period_start_pp = now;
+
+			if (0 == mdev->mali_metrics.num_running_gp_cores) {
+				MALI_DEBUG_ASSERT(mdev->mali_metrics.gpu_active == MALI_TRUE);
+				diff = ktime_sub(now, mdev->mali_metrics.time_period_start);
+				ns_time = (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+				mdev->mali_metrics.time_busy += ns_time;
+				mdev->mali_metrics.time_period_start = now;
+				mdev->mali_metrics.gpu_active = MALI_FALSE;
+			}
+		}
+	}
+
+	_mali_osk_spinlock_irq_unlock(mdev->mali_metrics.lock);
+}
+
+void mali_pm_record_gpu_active(mali_bool is_gp)
+{
+	ktime_t now;
+	ktime_t diff;
+	struct mali_device *mdev = dev_get_drvdata(&mali_platform_device->dev);
+
+	MALI_DEBUG_ASSERT(mdev != NULL);
+
+	_mali_osk_spinlock_irq_lock(mdev->mali_metrics.lock);
+	now = ktime_get();
+
+	if (MALI_TRUE == is_gp) {
+		mdev->mali_metrics.num_running_gp_cores++;
+		if (1 == mdev->mali_metrics.num_running_gp_cores) {
+			diff = ktime_sub(now, mdev->mali_metrics.time_period_start_gp);
+			mdev->mali_metrics.time_idle_gp += (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+			mdev->mali_metrics.time_period_start_gp = now;
+			if (0 == mdev->mali_metrics.num_running_pp_cores) {
+				MALI_DEBUG_ASSERT(mdev->mali_metrics.gpu_active == MALI_FALSE);
+				diff = ktime_sub(now, mdev->mali_metrics.time_period_start);
+				mdev->mali_metrics.time_idle += (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+				mdev->mali_metrics.time_period_start = now;
+				mdev->mali_metrics.gpu_active = MALI_TRUE;
+			}
+		} else {
+			MALI_DEBUG_ASSERT(mdev->mali_metrics.gpu_active == MALI_TRUE);
+		}
+	} else {
+		mdev->mali_metrics.num_running_pp_cores++;
+		if (1 == mdev->mali_metrics.num_running_pp_cores) {
+			diff = ktime_sub(now, mdev->mali_metrics.time_period_start_pp);
+			mdev->mali_metrics.time_idle_pp[0] += (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+			mdev->mali_metrics.time_period_start_pp = now;
+			if (0 == mdev->mali_metrics.num_running_gp_cores) {
+				MALI_DEBUG_ASSERT(mdev->mali_metrics.gpu_active == MALI_FALSE);
+				diff = ktime_sub(now, mdev->mali_metrics.time_period_start);
+				mdev->mali_metrics.time_idle += (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+				mdev->mali_metrics.time_period_start = now;
+				mdev->mali_metrics.gpu_active = MALI_TRUE;
+			}
+		} else {
+			MALI_DEBUG_ASSERT(mdev->mali_metrics.gpu_active == MALI_TRUE);
+		}
+	}
+
+	_mali_osk_spinlock_irq_unlock(mdev->mali_metrics.lock);
+}
+
+
+/*caller needs to hold mdev->mali_metrics.lock before calling this function*/
+static void mali_pm_get_dvfs_utilisation_calc(struct mali_device *mdev, ktime_t now)
+{
+	ktime_t diff;
+
+	MALI_DEBUG_ASSERT(mdev != NULL);
+
+	diff = ktime_sub(now, mdev->mali_metrics.time_period_start);
+
+	if (mdev->mali_metrics.gpu_active) {
+		mdev->mali_metrics.time_busy += (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+	} else {
+		mdev->mali_metrics.time_idle += (u64)(ktime_to_ns(diff) >> MALI_PM_TIME_SHIFT);
+	}
+}
+
+/* Caller needs to hold mdev->mali_metrics.lock before calling this function. */
+static void mali_pm_reset_dvfs_utilisation_unlocked(struct mali_device *mdev, ktime_t now)
+{
+	/* Store previous value */
+	mdev->mali_metrics.prev_idle = mdev->mali_metrics.time_idle;
+	mdev->mali_metrics.prev_busy = mdev->mali_metrics.time_busy;
+
+	/* Reset current values */
+	mdev->mali_metrics.time_period_start = now;
+	mdev->mali_metrics.time_period_start_gp = now;
+	mdev->mali_metrics.time_period_start_pp = now;
+	mdev->mali_metrics.time_idle = 0;
+	mdev->mali_metrics.time_busy = 0;
+
+	mdev->mali_metrics.time_busy_gp = 0;
+	mdev->mali_metrics.time_idle_gp = 0;
+	mdev->mali_metrics.time_busy_pp[0] = 0;
+	mdev->mali_metrics.time_idle_pp[0] = 0;
+}
+
+void mali_pm_reset_dvfs_utilisation(struct mali_device *mdev)
+{
+	_mali_osk_spinlock_irq_lock(mdev->mali_metrics.lock);
+	mali_pm_reset_dvfs_utilisation_unlocked(mdev, ktime_get());
+	_mali_osk_spinlock_irq_unlock(mdev->mali_metrics.lock);
+}
+
+void mali_pm_get_dvfs_utilisation(struct mali_device *mdev,
+				  unsigned long *total_out, unsigned long *busy_out)
+{
+	ktime_t now = ktime_get();
+	u64 busy = 0;
+	u64 total = 0;
+
+	_mali_osk_spinlock_irq_lock(mdev->mali_metrics.lock);
+
+	mali_pm_get_dvfs_utilisation_calc(mdev, now);
+
+	busy = mdev->mali_metrics.time_busy;
+	total = busy + mdev->mali_metrics.time_idle;
+
+	/* Reset stats if older than MALI_UTILIZATION_MAX_PERIOD (default
+	 * 100ms) */
+	if (total >= MALI_UTILIZATION_MAX_PERIOD) {
+		mali_pm_reset_dvfs_utilisation_unlocked(mdev, now);
+	} else if (total < (MALI_UTILIZATION_MAX_PERIOD / 2)) {
+		total += mdev->mali_metrics.prev_idle +
+			 mdev->mali_metrics.prev_busy;
+		busy += mdev->mali_metrics.prev_busy;
+	}
+
+	*total_out = (unsigned long)total;
+	*busy_out = (unsigned long)busy;
+	_mali_osk_spinlock_irq_unlock(mdev->mali_metrics.lock);
+}
+
+void mali_pm_metrics_spin_lock(void)
+{
+	struct mali_device *mdev = dev_get_drvdata(&mali_platform_device->dev);
+	_mali_osk_spinlock_irq_lock(mdev->mali_metrics.lock);
+}
+
+void mali_pm_metrics_spin_unlock(void)
+{
+	struct mali_device *mdev = dev_get_drvdata(&mali_platform_device->dev);
+	_mali_osk_spinlock_irq_unlock(mdev->mali_metrics.lock);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pm_metrics.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pm_metrics.h
@@ -0,0 +1,74 @@
+/*
+ * Copyright (C) 2010-2014, 2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PM_METRICS_H__
+#define __MALI_PM_METRICS_H__
+
+#ifdef CONFIG_MALI_DEVFREQ
+#include "mali_osk_locks.h"
+#include "mali_group.h"
+
+struct mali_device;
+
+/**
+ * Metrics data collected for use by the power management framework.
+ */
+struct mali_pm_metrics_data {
+	ktime_t time_period_start;
+	u64 time_busy;
+	u64 time_idle;
+	u64 prev_busy;
+	u64 prev_idle;
+	u32 num_running_gp_cores;
+	u32 num_running_pp_cores;
+	ktime_t time_period_start_gp;
+	u64 time_busy_gp;
+	u64 time_idle_gp;
+	ktime_t time_period_start_pp;
+	u64 time_busy_pp[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS];
+	u64 time_idle_pp[MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS];
+	mali_bool gpu_active;
+	_mali_osk_spinlock_irq_t *lock;
+};
+
+/**
+ * Initialize/start the Mali GPU pm_metrics metrics reporting.
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t mali_pm_metrics_init(struct mali_device *mdev);
+
+/**
+ * Terminate the Mali GPU pm_metrics metrics reporting
+ */
+void mali_pm_metrics_term(struct mali_device *mdev);
+
+/**
+ * Should be called when a job is about to execute a GPU job
+ */
+void mali_pm_record_gpu_active(mali_bool is_gp);
+
+/**
+ * Should be called when a job is finished
+ */
+void mali_pm_record_gpu_idle(mali_bool is_gp);
+
+void mali_pm_reset_dvfs_utilisation(struct mali_device *mdev);
+
+void mali_pm_get_dvfs_utilisation(struct mali_device *mdev, unsigned long *total_out, unsigned long *busy_out);
+
+void mali_pm_metrics_spin_lock(void);
+
+void mali_pm_metrics_spin_unlock(void);
+#else
+void mali_pm_record_gpu_idle(mali_bool is_gp) {}
+void mali_pm_record_gpu_active(mali_bool is_gp) {}
+#endif
+#endif /* __MALI_PM_METRICS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pmu.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pmu.c
@@ -0,0 +1,270 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_pmu.c
+ * Mali driver functions for Mali 400 PMU hardware
+ */
+#include "mali_hw_core.h"
+#include "mali_pmu.h"
+#include "mali_pp.h"
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_pm.h"
+#include "mali_osk_mali.h"
+
+struct mali_pmu_core *mali_global_pmu_core = NULL;
+
+static _mali_osk_errcode_t mali_pmu_wait_for_command_finish(
+	struct mali_pmu_core *pmu);
+
+struct mali_pmu_core *mali_pmu_create(_mali_osk_resource_t *resource)
+{
+	struct mali_pmu_core *pmu;
+
+	MALI_DEBUG_ASSERT(NULL == mali_global_pmu_core);
+	MALI_DEBUG_PRINT(2, ("Mali PMU: Creating Mali PMU core\n"));
+
+	pmu = (struct mali_pmu_core *)_mali_osk_malloc(
+		      sizeof(struct mali_pmu_core));
+	if (NULL != pmu) {
+		pmu->registered_cores_mask = 0; /* to be set later */
+
+		if (_MALI_OSK_ERR_OK == mali_hw_core_create(&pmu->hw_core,
+				resource, PMU_REGISTER_ADDRESS_SPACE_SIZE)) {
+
+			pmu->switch_delay = _mali_osk_get_pmu_switch_delay();
+
+			mali_global_pmu_core = pmu;
+
+			return pmu;
+		}
+		_mali_osk_free(pmu);
+	}
+
+	return NULL;
+}
+
+void mali_pmu_delete(struct mali_pmu_core *pmu)
+{
+	MALI_DEBUG_ASSERT_POINTER(pmu);
+	MALI_DEBUG_ASSERT(pmu == mali_global_pmu_core);
+
+	MALI_DEBUG_PRINT(2, ("Mali PMU: Deleting Mali PMU core\n"));
+
+	mali_global_pmu_core = NULL;
+
+	mali_hw_core_delete(&pmu->hw_core);
+	_mali_osk_free(pmu);
+}
+
+void mali_pmu_set_registered_cores_mask(struct mali_pmu_core *pmu, u32 mask)
+{
+	pmu->registered_cores_mask = mask;
+}
+
+void mali_pmu_reset(struct mali_pmu_core *pmu)
+{
+	MALI_DEBUG_ASSERT_POINTER(pmu);
+	MALI_DEBUG_ASSERT(pmu->registered_cores_mask != 0);
+
+	/* Setup the desired defaults */
+	mali_hw_core_register_write_relaxed(&pmu->hw_core,
+					    PMU_REG_ADDR_MGMT_INT_MASK, 0);
+	mali_hw_core_register_write_relaxed(&pmu->hw_core,
+					    PMU_REG_ADDR_MGMT_SW_DELAY, pmu->switch_delay);
+}
+
+void mali_pmu_power_up_all(struct mali_pmu_core *pmu)
+{
+	u32 stat;
+
+	MALI_DEBUG_ASSERT_POINTER(pmu);
+	MALI_DEBUG_ASSERT(pmu->registered_cores_mask != 0);
+
+	mali_pm_exec_lock();
+
+	mali_pmu_reset(pmu);
+
+	/* Now simply power up the domains which are marked as powered down */
+	stat = mali_hw_core_register_read(&pmu->hw_core,
+					  PMU_REG_ADDR_MGMT_STATUS);
+	mali_pmu_power_up(pmu, stat);
+
+	mali_pm_exec_unlock();
+}
+
+void mali_pmu_power_down_all(struct mali_pmu_core *pmu)
+{
+	u32 stat;
+
+	MALI_DEBUG_ASSERT_POINTER(pmu);
+	MALI_DEBUG_ASSERT(pmu->registered_cores_mask != 0);
+
+	mali_pm_exec_lock();
+
+	/* Now simply power down the domains which are marked as powered up */
+	stat = mali_hw_core_register_read(&pmu->hw_core,
+					  PMU_REG_ADDR_MGMT_STATUS);
+	mali_pmu_power_down(pmu, (~stat) & pmu->registered_cores_mask);
+
+	mali_pm_exec_unlock();
+}
+
+_mali_osk_errcode_t mali_pmu_power_down(struct mali_pmu_core *pmu, u32 mask)
+{
+	u32 stat;
+	_mali_osk_errcode_t err;
+
+	MALI_DEBUG_ASSERT_POINTER(pmu);
+	MALI_DEBUG_ASSERT(pmu->registered_cores_mask != 0);
+	MALI_DEBUG_ASSERT(mask <= pmu->registered_cores_mask);
+	MALI_DEBUG_ASSERT(0 == (mali_hw_core_register_read(&pmu->hw_core,
+				PMU_REG_ADDR_MGMT_INT_RAWSTAT) &
+				PMU_REG_VAL_IRQ));
+
+	MALI_DEBUG_PRINT(3,
+			 ("PMU power down: ...................... [%s]\n",
+			  mali_pm_mask_to_string(mask)));
+
+	stat = mali_hw_core_register_read(&pmu->hw_core,
+					  PMU_REG_ADDR_MGMT_STATUS);
+
+	/*
+	 * Assert that we are not powering down domains which are already
+	 * powered down.
+	 */
+	MALI_DEBUG_ASSERT(0 == (stat & mask));
+
+	mask  &= ~(0x1 << MALI_DOMAIN_INDEX_DUMMY);
+
+	if (0 == mask || 0 == ((~stat) & mask)) return _MALI_OSK_ERR_OK;
+
+	mali_hw_core_register_write(&pmu->hw_core,
+				    PMU_REG_ADDR_MGMT_POWER_DOWN, mask);
+
+	/*
+	 * Do not wait for interrupt on Mali-300/400 if all domains are
+	 * powered off by our power down command, because the HW will simply
+	 * not generate an interrupt in this case.
+	 */
+	if (mali_is_mali450() || mali_is_mali470() || pmu->registered_cores_mask != (mask | stat)) {
+		err = mali_pmu_wait_for_command_finish(pmu);
+		if (_MALI_OSK_ERR_OK != err) {
+			return err;
+		}
+	} else {
+		mali_hw_core_register_write(&pmu->hw_core,
+					    PMU_REG_ADDR_MGMT_INT_CLEAR, PMU_REG_VAL_IRQ);
+	}
+
+#if defined(DEBUG)
+	/* Verify power status of domains after power down */
+	stat = mali_hw_core_register_read(&pmu->hw_core,
+					  PMU_REG_ADDR_MGMT_STATUS);
+	MALI_DEBUG_ASSERT(mask == (stat & mask));
+#endif
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_pmu_power_up(struct mali_pmu_core *pmu, u32 mask)
+{
+	u32 stat;
+	_mali_osk_errcode_t err;
+#if !defined(CONFIG_MALI_PMU_PARALLEL_POWER_UP)
+	u32 current_domain;
+#endif
+
+	MALI_DEBUG_ASSERT_POINTER(pmu);
+	MALI_DEBUG_ASSERT(pmu->registered_cores_mask != 0);
+	MALI_DEBUG_ASSERT(mask <= pmu->registered_cores_mask);
+	MALI_DEBUG_ASSERT(0 == (mali_hw_core_register_read(&pmu->hw_core,
+				PMU_REG_ADDR_MGMT_INT_RAWSTAT) &
+				PMU_REG_VAL_IRQ));
+
+	MALI_DEBUG_PRINT(3,
+			 ("PMU power up: ........................ [%s]\n",
+			  mali_pm_mask_to_string(mask)));
+
+	stat = mali_hw_core_register_read(&pmu->hw_core,
+					  PMU_REG_ADDR_MGMT_STATUS);
+	stat &= pmu->registered_cores_mask;
+
+	mask  &= ~(0x1 << MALI_DOMAIN_INDEX_DUMMY);
+	if (0 == mask || 0 == (stat & mask)) return _MALI_OSK_ERR_OK;
+
+	/*
+	 * Assert that we are only powering up domains which are currently
+	 * powered down.
+	 */
+	MALI_DEBUG_ASSERT(mask == (stat & mask));
+
+#if defined(CONFIG_MALI_PMU_PARALLEL_POWER_UP)
+	mali_hw_core_register_write(&pmu->hw_core,
+				    PMU_REG_ADDR_MGMT_POWER_UP, mask);
+
+	err = mali_pmu_wait_for_command_finish(pmu);
+	if (_MALI_OSK_ERR_OK != err) {
+		return err;
+	}
+#else
+	for (current_domain = 1;
+	     current_domain <= pmu->registered_cores_mask;
+	     current_domain <<= 1) {
+		if (current_domain & mask & stat) {
+			mali_hw_core_register_write(&pmu->hw_core,
+						    PMU_REG_ADDR_MGMT_POWER_UP,
+						    current_domain);
+
+			err = mali_pmu_wait_for_command_finish(pmu);
+			if (_MALI_OSK_ERR_OK != err) {
+				return err;
+			}
+		}
+	}
+#endif
+
+#if defined(DEBUG)
+	/* Verify power status of domains after power up */
+	stat = mali_hw_core_register_read(&pmu->hw_core,
+					  PMU_REG_ADDR_MGMT_STATUS);
+	MALI_DEBUG_ASSERT(0 == (stat & mask));
+#endif /* defined(DEBUG) */
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static _mali_osk_errcode_t mali_pmu_wait_for_command_finish(
+	struct mali_pmu_core *pmu)
+{
+	u32 rawstat;
+	u32 timeout = MALI_REG_POLL_COUNT_SLOW;
+
+	MALI_DEBUG_ASSERT(pmu);
+
+	/* Wait for the command to complete */
+	do {
+		rawstat = mali_hw_core_register_read(&pmu->hw_core,
+						     PMU_REG_ADDR_MGMT_INT_RAWSTAT);
+		--timeout;
+	} while (0 == (rawstat & PMU_REG_VAL_IRQ) && 0 < timeout);
+
+	MALI_DEBUG_ASSERT(0 < timeout);
+
+	if (0 == timeout) {
+		return _MALI_OSK_ERR_TIMEOUT;
+	}
+
+	mali_hw_core_register_write(&pmu->hw_core,
+				    PMU_REG_ADDR_MGMT_INT_CLEAR, PMU_REG_VAL_IRQ);
+
+	return _MALI_OSK_ERR_OK;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pmu.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pmu.h
@@ -0,0 +1,123 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_platform.h
+ * Platform specific Mali driver functions
+ */
+
+#ifndef __MALI_PMU_H__
+#define __MALI_PMU_H__
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_hw_core.h"
+
+/** @brief MALI inbuilt PMU hardware info and PMU hardware has knowledge of cores power mask
+ */
+struct mali_pmu_core {
+	struct mali_hw_core hw_core;
+	u32 registered_cores_mask;
+	u32 switch_delay;
+};
+
+/** @brief Register layout for hardware PMU
+ */
+typedef enum {
+	PMU_REG_ADDR_MGMT_POWER_UP                  = 0x00,     /*< Power up register */
+	PMU_REG_ADDR_MGMT_POWER_DOWN                = 0x04,     /*< Power down register */
+	PMU_REG_ADDR_MGMT_STATUS                    = 0x08,     /*< Core sleep status register */
+	PMU_REG_ADDR_MGMT_INT_MASK                  = 0x0C,     /*< Interrupt mask register */
+	PMU_REG_ADDR_MGMT_INT_RAWSTAT               = 0x10,     /*< Interrupt raw status register */
+	PMU_REG_ADDR_MGMT_INT_CLEAR                 = 0x18,     /*< Interrupt clear register */
+	PMU_REG_ADDR_MGMT_SW_DELAY                  = 0x1C,     /*< Switch delay register */
+	PMU_REGISTER_ADDRESS_SPACE_SIZE             = 0x28,     /*< Size of register space */
+} pmu_reg_addr_mgmt_addr;
+
+#define PMU_REG_VAL_IRQ 1
+
+extern struct mali_pmu_core *mali_global_pmu_core;
+
+/** @brief Initialisation of MALI PMU
+ *
+ * This is called from entry point of the driver in order to create and intialize the PMU resource
+ *
+ * @param resource it will be a pointer to a PMU resource
+ * @param number_of_pp_cores Number of found PP resources in configuration
+ * @param number_of_l2_caches Number of found L2 cache resources in configuration
+ * @return The created PMU object, or NULL in case of failure.
+ */
+struct mali_pmu_core *mali_pmu_create(_mali_osk_resource_t *resource);
+
+/** @brief It deallocates the PMU resource
+ *
+ * This is called on the exit of the driver to terminate the PMU resource
+ *
+ * @param pmu Pointer to PMU core object to delete
+ */
+void mali_pmu_delete(struct mali_pmu_core *pmu);
+
+/** @brief Set registered cores mask
+ *
+ * @param pmu Pointer to PMU core object
+ * @param mask All available/valid domain bits
+ */
+void mali_pmu_set_registered_cores_mask(struct mali_pmu_core *pmu, u32 mask);
+
+/** @brief Retrieves the Mali PMU core object (if any)
+ *
+ * @return The Mali PMU object, or NULL if no PMU exists.
+ */
+MALI_STATIC_INLINE struct mali_pmu_core *mali_pmu_get_global_pmu_core(void)
+{
+	return mali_global_pmu_core;
+}
+
+/** @brief Reset PMU core
+ *
+ * @param pmu Pointer to PMU core object to reset
+ */
+void mali_pmu_reset(struct mali_pmu_core *pmu);
+
+void mali_pmu_power_up_all(struct mali_pmu_core *pmu);
+
+void mali_pmu_power_down_all(struct mali_pmu_core *pmu);
+
+/** @brief Returns a mask of the currently powered up domains
+ *
+ * @param pmu Pointer to PMU core object
+ */
+MALI_STATIC_INLINE u32 mali_pmu_get_mask(struct mali_pmu_core *pmu)
+{
+	u32 stat = mali_hw_core_register_read(&pmu->hw_core, PMU_REG_ADDR_MGMT_STATUS);
+	return ((~stat) & pmu->registered_cores_mask);
+}
+
+/** @brief MALI GPU power down using MALI in-built PMU
+ *
+ * Called to power down the specified cores.
+ *
+ * @param pmu Pointer to PMU core object to power down
+ * @param mask Mask specifying which power domains to power down
+ * @return _MALI_OSK_ERR_OK on success otherwise, a suitable _mali_osk_errcode_t error.
+ */
+_mali_osk_errcode_t mali_pmu_power_down(struct mali_pmu_core *pmu, u32 mask);
+
+/** @brief MALI GPU power up using MALI in-built PMU
+ *
+ * Called to power up the specified cores.
+ *
+ * @param pmu Pointer to PMU core object to power up
+ * @param mask Mask specifying which power domains to power up
+ * @return _MALI_OSK_ERR_OK on success otherwise, a suitable _mali_osk_errcode_t error.
+ */
+_mali_osk_errcode_t mali_pmu_power_up(struct mali_pmu_core *pmu, u32 mask);
+
+#endif /* __MALI_PMU_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pp.c
@@ -0,0 +1,502 @@
+/*
+ * Copyright (C) 2011-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_pp_job.h"
+#include "mali_pp.h"
+#include "mali_hw_core.h"
+#include "mali_group.h"
+#include "regs/mali_200_regs.h"
+#include "mali_kernel_common.h"
+#include "mali_kernel_core.h"
+
+#if defined(CONFIG_MALI400_PROFILING)
+#include "mali_osk_profiling.h"
+#endif
+
+/* Number of frame registers on Mali-200 */
+#define MALI_PP_MALI200_NUM_FRAME_REGISTERS ((0x04C/4)+1)
+/* Number of frame registers on Mali-300 and later */
+#define MALI_PP_MALI400_NUM_FRAME_REGISTERS ((0x058/4)+1)
+
+static struct mali_pp_core *mali_global_pp_cores[MALI_MAX_NUMBER_OF_PP_CORES] = { NULL };
+static u32 mali_global_num_pp_cores = 0;
+
+/* Interrupt handlers */
+static void mali_pp_irq_probe_trigger(void *data);
+static _mali_osk_errcode_t mali_pp_irq_probe_ack(void *data);
+
+struct mali_pp_core *mali_pp_create(const _mali_osk_resource_t *resource, struct mali_group *group, mali_bool is_virtual, u32 bcast_id)
+{
+	struct mali_pp_core *core = NULL;
+
+	MALI_DEBUG_PRINT(2, ("Mali PP: Creating Mali PP core: %s\n", resource->description));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Base address of PP core: 0x%x\n", resource->base));
+
+	if (mali_global_num_pp_cores >= MALI_MAX_NUMBER_OF_PP_CORES) {
+		MALI_PRINT_ERROR(("Mali PP: Too many PP core objects created\n"));
+		return NULL;
+	}
+
+	core = _mali_osk_calloc(1, sizeof(struct mali_pp_core));
+	if (NULL != core) {
+		core->core_id = mali_global_num_pp_cores;
+		core->bcast_id = bcast_id;
+
+		if (_MALI_OSK_ERR_OK == mali_hw_core_create(&core->hw_core, resource, MALI200_REG_SIZEOF_REGISTER_BANK)) {
+			_mali_osk_errcode_t ret;
+
+			if (!is_virtual) {
+				ret = mali_pp_reset(core);
+			} else {
+				ret = _MALI_OSK_ERR_OK;
+			}
+
+			if (_MALI_OSK_ERR_OK == ret) {
+				ret = mali_group_add_pp_core(group, core);
+				if (_MALI_OSK_ERR_OK == ret) {
+					/* Setup IRQ handlers (which will do IRQ probing if needed) */
+					MALI_DEBUG_ASSERT(!is_virtual || -1 != resource->irq);
+
+					core->irq = _mali_osk_irq_init(resource->irq,
+								       mali_group_upper_half_pp,
+								       group,
+								       mali_pp_irq_probe_trigger,
+								       mali_pp_irq_probe_ack,
+								       core,
+								       resource->description);
+					if (NULL != core->irq) {
+						mali_global_pp_cores[mali_global_num_pp_cores] = core;
+						mali_global_num_pp_cores++;
+
+						return core;
+					} else {
+						MALI_PRINT_ERROR(("Mali PP: Failed to setup interrupt handlers for PP core %s\n", core->hw_core.description));
+					}
+					mali_group_remove_pp_core(group);
+				} else {
+					MALI_PRINT_ERROR(("Mali PP: Failed to add core %s to group\n", core->hw_core.description));
+				}
+			}
+			mali_hw_core_delete(&core->hw_core);
+		}
+
+		_mali_osk_free(core);
+	} else {
+		MALI_PRINT_ERROR(("Mali PP: Failed to allocate memory for PP core\n"));
+	}
+
+	return NULL;
+}
+
+void mali_pp_delete(struct mali_pp_core *core)
+{
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	_mali_osk_irq_term(core->irq);
+	mali_hw_core_delete(&core->hw_core);
+
+	/* Remove core from global list */
+	for (i = 0; i < mali_global_num_pp_cores; i++) {
+		if (mali_global_pp_cores[i] == core) {
+			mali_global_pp_cores[i] = NULL;
+			mali_global_num_pp_cores--;
+
+			if (i != mali_global_num_pp_cores) {
+				/* We removed a PP core from the middle of the array -- move the last
+				 * PP core to the current position to close the gap */
+				mali_global_pp_cores[i] = mali_global_pp_cores[mali_global_num_pp_cores];
+				mali_global_pp_cores[mali_global_num_pp_cores] = NULL;
+			}
+
+			break;
+		}
+	}
+
+	_mali_osk_free(core);
+}
+
+void mali_pp_stop_bus(struct mali_pp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	/* Will only send the stop bus command, and not wait for it to complete */
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_CTRL_MGMT, MALI200_REG_VAL_CTRL_MGMT_STOP_BUS);
+}
+
+_mali_osk_errcode_t mali_pp_stop_bus_wait(struct mali_pp_core *core)
+{
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	/* Send the stop bus command. */
+	mali_pp_stop_bus(core);
+
+	/* Wait for bus to be stopped */
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; i++) {
+		if (mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_STATUS) & MALI200_REG_VAL_STATUS_BUS_STOPPED)
+			break;
+	}
+
+	if (MALI_REG_POLL_COUNT_FAST == i) {
+		MALI_PRINT_ERROR(("Mali PP: Failed to stop bus on %s. Status: 0x%08x\n", core->hw_core.description, mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_STATUS)));
+		return _MALI_OSK_ERR_FAULT;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+/* Frame register reset values.
+ * Taken from the Mali400 TRM, 3.6. Pixel processor control register summary */
+static const u32 mali_frame_registers_reset_values[_MALI_PP_MAX_FRAME_REGISTERS] = {
+	0x0, /* Renderer List Address Register */
+	0x0, /* Renderer State Word Base Address Register */
+	0x0, /* Renderer Vertex Base Register */
+	0x2, /* Feature Enable Register */
+	0x0, /* Z Clear Value Register */
+	0x0, /* Stencil Clear Value Register */
+	0x0, /* ABGR Clear Value 0 Register */
+	0x0, /* ABGR Clear Value 1 Register */
+	0x0, /* ABGR Clear Value 2 Register */
+	0x0, /* ABGR Clear Value 3 Register */
+	0x0, /* Bounding Box Left Right Register */
+	0x0, /* Bounding Box Bottom Register */
+	0x0, /* FS Stack Address Register */
+	0x0, /* FS Stack Size and Initial Value Register */
+	0x0, /* Reserved */
+	0x0, /* Reserved */
+	0x0, /* Origin Offset X Register */
+	0x0, /* Origin Offset Y Register */
+	0x75, /* Subpixel Specifier Register */
+	0x0, /* Tiebreak mode Register */
+	0x0, /* Polygon List Format Register */
+	0x0, /* Scaling Register */
+	0x0 /* Tilebuffer configuration Register */
+};
+
+/* WBx register reset values */
+static const u32 mali_wb_registers_reset_values[_MALI_PP_MAX_WB_REGISTERS] = {
+	0x0, /* WBx Source Select Register */
+	0x0, /* WBx Target Address Register */
+	0x0, /* WBx Target Pixel Format Register */
+	0x0, /* WBx Target AA Format Register */
+	0x0, /* WBx Target Layout */
+	0x0, /* WBx Target Scanline Length */
+	0x0, /* WBx Target Flags Register */
+	0x0, /* WBx MRT Enable Register */
+	0x0, /* WBx MRT Offset Register */
+	0x0, /* WBx Global Test Enable Register */
+	0x0, /* WBx Global Test Reference Value Register */
+	0x0  /* WBx Global Test Compare Function Register */
+};
+
+/* Performance Counter 0 Enable Register reset value */
+static const u32 mali_perf_cnt_enable_reset_value = 0;
+
+_mali_osk_errcode_t mali_pp_hard_reset(struct mali_pp_core *core)
+{
+	/* Bus must be stopped before calling this function */
+	const u32 reset_wait_target_register = MALI200_REG_ADDR_MGMT_PERF_CNT_0_LIMIT;
+	const u32 reset_invalid_value = 0xC0FFE000;
+	const u32 reset_check_value = 0xC01A0000;
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+	MALI_DEBUG_PRINT(2, ("Mali PP: Hard reset of core %s\n", core->hw_core.description));
+
+	/* Set register to a bogus value. The register will be used to detect when reset is complete */
+	mali_hw_core_register_write_relaxed(&core->hw_core, reset_wait_target_register, reset_invalid_value);
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, MALI200_REG_VAL_IRQ_MASK_NONE);
+
+	/* Force core to reset */
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_CTRL_MGMT, MALI200_REG_VAL_CTRL_MGMT_FORCE_RESET);
+
+	/* Wait for reset to be complete */
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; i++) {
+		mali_hw_core_register_write(&core->hw_core, reset_wait_target_register, reset_check_value);
+		if (reset_check_value == mali_hw_core_register_read(&core->hw_core, reset_wait_target_register)) {
+			break;
+		}
+	}
+
+	if (MALI_REG_POLL_COUNT_FAST == i) {
+		MALI_PRINT_ERROR(("Mali PP: The hard reset loop didn't work, unable to recover\n"));
+	}
+
+	mali_hw_core_register_write(&core->hw_core, reset_wait_target_register, 0x00000000); /* set it back to the default */
+	/* Re-enable interrupts */
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_CLEAR, MALI200_REG_VAL_IRQ_MASK_ALL);
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, MALI200_REG_VAL_IRQ_MASK_USED);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_pp_reset_async(struct mali_pp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	MALI_DEBUG_PRINT(4, ("Mali PP: Reset of core %s\n", core->hw_core.description));
+
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, 0); /* disable the IRQs */
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_RAWSTAT, MALI200_REG_VAL_IRQ_MASK_ALL);
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_CTRL_MGMT, MALI400PP_REG_VAL_CTRL_MGMT_SOFT_RESET);
+}
+
+_mali_osk_errcode_t mali_pp_reset_wait(struct mali_pp_core *core)
+{
+	int i;
+	u32 rawstat = 0;
+
+	for (i = 0; i < MALI_REG_POLL_COUNT_FAST; i++) {
+		u32 status =  mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_STATUS);
+		if (!(status & MALI200_REG_VAL_STATUS_RENDERING_ACTIVE)) {
+			rawstat = mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_RAWSTAT);
+			if (rawstat == MALI400PP_REG_VAL_IRQ_RESET_COMPLETED) {
+				break;
+			}
+		}
+	}
+
+	if (i == MALI_REG_POLL_COUNT_FAST) {
+		MALI_PRINT_ERROR(("Mali PP: Failed to reset core %s, rawstat: 0x%08x\n",
+				  core->hw_core.description, rawstat));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Re-enable interrupts */
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_CLEAR, MALI200_REG_VAL_IRQ_MASK_ALL);
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, MALI200_REG_VAL_IRQ_MASK_USED);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_pp_reset(struct mali_pp_core *core)
+{
+	mali_pp_reset_async(core);
+	return mali_pp_reset_wait(core);
+}
+
+void mali_pp_job_start(struct mali_pp_core *core, struct mali_pp_job *job, u32 sub_job, mali_bool restart_virtual)
+{
+	u32 relative_address;
+	u32 start_index;
+	u32 nr_of_regs;
+	u32 *frame_registers = mali_pp_job_get_frame_registers(job);
+	u32 *wb0_registers = mali_pp_job_get_wb0_registers(job);
+	u32 *wb1_registers = mali_pp_job_get_wb1_registers(job);
+	u32 *wb2_registers = mali_pp_job_get_wb2_registers(job);
+	u32 counter_src0 = mali_pp_job_get_perf_counter_src0(job, sub_job);
+	u32 counter_src1 = mali_pp_job_get_perf_counter_src1(job, sub_job);
+
+	MALI_DEBUG_ASSERT_POINTER(core);
+
+	/* Write frame registers */
+
+	/*
+	 * There are two frame registers which are different for each sub job:
+	 * 1. The Renderer List Address Register (MALI200_REG_ADDR_FRAME)
+	 * 2. The FS Stack Address Register (MALI200_REG_ADDR_STACK)
+	 */
+	mali_hw_core_register_write_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_FRAME, mali_pp_job_get_addr_frame(job, sub_job), mali_frame_registers_reset_values[MALI200_REG_ADDR_FRAME / sizeof(u32)]);
+
+	/* For virtual jobs, the stack address shouldn't be broadcast but written individually */
+	if (!mali_pp_job_is_virtual(job) || restart_virtual) {
+		mali_hw_core_register_write_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_STACK, mali_pp_job_get_addr_stack(job, sub_job), mali_frame_registers_reset_values[MALI200_REG_ADDR_STACK / sizeof(u32)]);
+	}
+
+	/* Write registers between MALI200_REG_ADDR_FRAME and MALI200_REG_ADDR_STACK */
+	relative_address = MALI200_REG_ADDR_RSW;
+	start_index = MALI200_REG_ADDR_RSW / sizeof(u32);
+	nr_of_regs = (MALI200_REG_ADDR_STACK - MALI200_REG_ADDR_RSW) / sizeof(u32);
+
+	mali_hw_core_register_write_array_relaxed_conditional(&core->hw_core,
+			relative_address, &frame_registers[start_index],
+			nr_of_regs, &mali_frame_registers_reset_values[start_index]);
+
+	/* MALI200_REG_ADDR_STACK_SIZE */
+	relative_address = MALI200_REG_ADDR_STACK_SIZE;
+	start_index = MALI200_REG_ADDR_STACK_SIZE / sizeof(u32);
+
+	mali_hw_core_register_write_relaxed_conditional(&core->hw_core,
+			relative_address, frame_registers[start_index],
+			mali_frame_registers_reset_values[start_index]);
+
+	/* Skip 2 reserved registers */
+
+	/* Write remaining registers */
+	relative_address = MALI200_REG_ADDR_ORIGIN_OFFSET_X;
+	start_index = MALI200_REG_ADDR_ORIGIN_OFFSET_X / sizeof(u32);
+	nr_of_regs = MALI_PP_MALI400_NUM_FRAME_REGISTERS - MALI200_REG_ADDR_ORIGIN_OFFSET_X / sizeof(u32);
+
+	mali_hw_core_register_write_array_relaxed_conditional(&core->hw_core,
+			relative_address, &frame_registers[start_index],
+			nr_of_regs, &mali_frame_registers_reset_values[start_index]);
+
+	/* Write WBx registers */
+	if (wb0_registers[0]) { /* M200_WB0_REG_SOURCE_SELECT register */
+		mali_hw_core_register_write_array_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_WB0, wb0_registers, _MALI_PP_MAX_WB_REGISTERS, mali_wb_registers_reset_values);
+	}
+
+	if (wb1_registers[0]) { /* M200_WB1_REG_SOURCE_SELECT register */
+		mali_hw_core_register_write_array_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_WB1, wb1_registers, _MALI_PP_MAX_WB_REGISTERS, mali_wb_registers_reset_values);
+	}
+
+	if (wb2_registers[0]) { /* M200_WB2_REG_SOURCE_SELECT register */
+		mali_hw_core_register_write_array_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_WB2, wb2_registers, _MALI_PP_MAX_WB_REGISTERS, mali_wb_registers_reset_values);
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER != counter_src0) {
+		mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_0_SRC, counter_src0);
+		mali_hw_core_register_write_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_0_ENABLE, MALI200_REG_VAL_PERF_CNT_ENABLE, mali_perf_cnt_enable_reset_value);
+	}
+	if (MALI_HW_CORE_NO_COUNTER != counter_src1) {
+		mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_1_SRC, counter_src1);
+		mali_hw_core_register_write_relaxed_conditional(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_1_ENABLE, MALI200_REG_VAL_PERF_CNT_ENABLE, mali_perf_cnt_enable_reset_value);
+	}
+
+#ifdef CONFIG_MALI400_HEATMAPS_ENABLED
+	if (job->uargs.perf_counter_flag & _MALI_PERFORMANCE_COUNTER_FLAG_HEATMAP_ENABLE) {
+		mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_MGMT_PERFMON_CONTR, ((job->uargs.tilesx & 0x3FF) << 16) | 1);
+		mali_hw_core_register_write_relaxed(&core->hw_core,  MALI200_REG_ADDR_MGMT_PERFMON_BASE, job->uargs.heatmap_mem & 0xFFFFFFF8);
+	}
+#endif /* CONFIG_MALI400_HEATMAPS_ENABLED */
+
+	MALI_DEBUG_PRINT(3, ("Mali PP: Starting job 0x%08X part %u/%u on PP core %s\n", job, sub_job + 1, mali_pp_job_get_sub_job_count(job), core->hw_core.description));
+
+	/* Adding barrier to make sure all rester writes are finished */
+	_mali_osk_write_mem_barrier();
+
+	/* This is the command that starts the core.
+	 *
+	 * Don't actually run the job if PROFILING_SKIP_PP_JOBS are set, just
+	 * force core to assert the completion interrupt.
+	 */
+#if !defined(PROFILING_SKIP_PP_JOBS)
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_MGMT_CTRL_MGMT, MALI200_REG_VAL_CTRL_MGMT_START_RENDERING);
+#else
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_RAWSTAT, MALI200_REG_VAL_IRQ_END_OF_FRAME);
+#endif
+
+	/* Adding barrier to make sure previous rester writes is finished */
+	_mali_osk_write_mem_barrier();
+}
+
+u32 mali_pp_core_get_version(struct mali_pp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	return mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_VERSION);
+}
+
+struct mali_pp_core *mali_pp_get_global_pp_core(u32 index)
+{
+	if (mali_global_num_pp_cores > index) {
+		return mali_global_pp_cores[index];
+	}
+
+	return NULL;
+}
+
+u32 mali_pp_get_glob_num_pp_cores(void)
+{
+	return mali_global_num_pp_cores;
+}
+
+/* ------------- interrupt handling below ------------------ */
+static void mali_pp_irq_probe_trigger(void *data)
+{
+	struct mali_pp_core *core = (struct mali_pp_core *)data;
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, MALI200_REG_VAL_IRQ_MASK_USED);
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_RAWSTAT, MALI200_REG_VAL_IRQ_BUS_ERROR);
+	_mali_osk_mem_barrier();
+}
+
+static _mali_osk_errcode_t mali_pp_irq_probe_ack(void *data)
+{
+	struct mali_pp_core *core = (struct mali_pp_core *)data;
+	u32 irq_readout;
+
+	irq_readout = mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_STATUS);
+	if (MALI200_REG_VAL_IRQ_BUS_ERROR & irq_readout) {
+		mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_CLEAR, MALI200_REG_VAL_IRQ_BUS_ERROR);
+		_mali_osk_mem_barrier();
+		return _MALI_OSK_ERR_OK;
+	}
+
+	return _MALI_OSK_ERR_FAULT;
+}
+
+
+#if 0
+static void mali_pp_print_registers(struct mali_pp_core *core)
+{
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_VERSION = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_VERSION)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_CURRENT_REND_LIST_ADDR = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_CURRENT_REND_LIST_ADDR)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_STATUS = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_STATUS)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_INT_RAWSTAT = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_RAWSTAT)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_INT_MASK = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_INT_STATUS = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_STATUS)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_BUS_ERROR_STATUS = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_BUS_ERROR_STATUS)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_PERF_CNT_0_ENABLE = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_0_ENABLE)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_PERF_CNT_0_SRC = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_0_SRC)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_PERF_CNT_0_VALUE = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_0_VALUE)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_PERF_CNT_1_ENABLE = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_1_ENABLE)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_PERF_CNT_1_SRC = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_1_SRC)));
+	MALI_DEBUG_PRINT(2, ("Mali PP: Register MALI200_REG_ADDR_MGMT_PERF_CNT_1_VALUE = 0x%08X\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_1_VALUE)));
+}
+#endif
+
+#if 0
+void mali_pp_print_state(struct mali_pp_core *core)
+{
+	MALI_DEBUG_PRINT(2, ("Mali PP: State: 0x%08x\n", mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_STATUS)));
+}
+#endif
+
+void mali_pp_update_performance_counters(struct mali_pp_core *parent, struct mali_pp_core *child, struct mali_pp_job *job, u32 subjob)
+{
+	u32 val0 = 0;
+	u32 val1 = 0;
+	u32 counter_src0 = mali_pp_job_get_perf_counter_src0(job, subjob);
+	u32 counter_src1 = mali_pp_job_get_perf_counter_src1(job, subjob);
+#if defined(CONFIG_MALI400_PROFILING)
+	int counter_index = COUNTER_FP_0_C0 + (2 * child->core_id);
+#endif
+
+	if (MALI_HW_CORE_NO_COUNTER != counter_src0) {
+		val0 = mali_hw_core_register_read(&child->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_0_VALUE);
+		mali_pp_job_set_perf_counter_value0(job, subjob, val0);
+
+#if defined(CONFIG_MALI400_PROFILING)
+		_mali_osk_profiling_report_hw_counter(counter_index, val0);
+		_mali_osk_profiling_record_global_counters(counter_index, val0);
+#endif
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER != counter_src1) {
+		val1 = mali_hw_core_register_read(&child->hw_core, MALI200_REG_ADDR_MGMT_PERF_CNT_1_VALUE);
+		mali_pp_job_set_perf_counter_value1(job, subjob, val1);
+
+#if defined(CONFIG_MALI400_PROFILING)
+		_mali_osk_profiling_report_hw_counter(counter_index + 1, val1);
+		_mali_osk_profiling_record_global_counters(counter_index + 1, val1);
+#endif
+	}
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_pp_dump_state(struct mali_pp_core *core, char *buf, u32 size)
+{
+	int n = 0;
+
+	n += _mali_osk_snprintf(buf + n, size - n, "\tPP #%d: %s\n", core->core_id, core->hw_core.description);
+
+	return n;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pp.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pp.h
@@ -0,0 +1,138 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PP_H__
+#define __MALI_PP_H__
+
+#include "mali_osk.h"
+#include "mali_pp_job.h"
+#include "mali_hw_core.h"
+
+struct mali_group;
+
+#define MALI_MAX_NUMBER_OF_PP_CORES        9
+
+/**
+ * Definition of the PP core struct
+ * Used to track a PP core in the system.
+ */
+struct mali_pp_core {
+	struct mali_hw_core  hw_core;           /**< Common for all HW cores */
+	_mali_osk_irq_t     *irq;               /**< IRQ handler */
+	u32                  core_id;           /**< Unique core ID */
+	u32                  bcast_id;          /**< The "flag" value used by the Mali-450 broadcast and DLBU unit */
+};
+
+_mali_osk_errcode_t mali_pp_initialize(void);
+void mali_pp_terminate(void);
+
+struct mali_pp_core *mali_pp_create(const _mali_osk_resource_t *resource, struct mali_group *group, mali_bool is_virtual, u32 bcast_id);
+void mali_pp_delete(struct mali_pp_core *core);
+
+void mali_pp_stop_bus(struct mali_pp_core *core);
+_mali_osk_errcode_t mali_pp_stop_bus_wait(struct mali_pp_core *core);
+void mali_pp_reset_async(struct mali_pp_core *core);
+_mali_osk_errcode_t mali_pp_reset_wait(struct mali_pp_core *core);
+_mali_osk_errcode_t mali_pp_reset(struct mali_pp_core *core);
+_mali_osk_errcode_t mali_pp_hard_reset(struct mali_pp_core *core);
+
+void mali_pp_job_start(struct mali_pp_core *core, struct mali_pp_job *job, u32 sub_job, mali_bool restart_virtual);
+
+u32 mali_pp_core_get_version(struct mali_pp_core *core);
+
+MALI_STATIC_INLINE u32 mali_pp_core_get_id(struct mali_pp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	return core->core_id;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_core_get_bcast_id(struct mali_pp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	return core->bcast_id;
+}
+
+struct mali_pp_core *mali_pp_get_global_pp_core(u32 index);
+u32 mali_pp_get_glob_num_pp_cores(void);
+
+/* Debug */
+u32 mali_pp_dump_state(struct mali_pp_core *core, char *buf, u32 size);
+
+/**
+ * Put instrumented HW counters from the core(s) to the job object (if enabled)
+ *
+ * parent and child is always the same, except for virtual jobs on Mali-450.
+ * In this case, the counters will be enabled on the virtual core (parent),
+ * but values need to be read from the child cores.
+ *
+ * @param parent The core used to see if the counters was enabled
+ * @param child The core to actually read the values from
+ * @job Job object to update with counter values (if enabled)
+ * @subjob Which subjob the counters are applicable for (core ID for virtual jobs)
+ */
+void mali_pp_update_performance_counters(struct mali_pp_core *parent, struct mali_pp_core *child, struct mali_pp_job *job, u32 subjob);
+
+MALI_STATIC_INLINE const char *mali_pp_core_description(struct mali_pp_core *core)
+{
+	return core->hw_core.description;
+}
+
+MALI_STATIC_INLINE enum mali_interrupt_result mali_pp_get_interrupt_result(struct mali_pp_core *core)
+{
+	u32 rawstat_used = mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_RAWSTAT) &
+			   MALI200_REG_VAL_IRQ_MASK_USED;
+	if (0 == rawstat_used) {
+		return MALI_INTERRUPT_RESULT_NONE;
+	} else if (MALI200_REG_VAL_IRQ_END_OF_FRAME == rawstat_used) {
+		return MALI_INTERRUPT_RESULT_SUCCESS;
+	}
+
+	return MALI_INTERRUPT_RESULT_ERROR;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_get_rawstat(struct mali_pp_core *core)
+{
+	MALI_DEBUG_ASSERT_POINTER(core);
+	return mali_hw_core_register_read(&core->hw_core,
+					  MALI200_REG_ADDR_MGMT_INT_RAWSTAT);
+}
+
+
+MALI_STATIC_INLINE u32 mali_pp_is_active(struct mali_pp_core *core)
+{
+	u32 status = mali_hw_core_register_read(&core->hw_core, MALI200_REG_ADDR_MGMT_STATUS);
+	return (status & MALI200_REG_VAL_STATUS_RENDERING_ACTIVE) ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE void mali_pp_mask_all_interrupts(struct mali_pp_core *core)
+{
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, MALI200_REG_VAL_IRQ_MASK_NONE);
+}
+
+MALI_STATIC_INLINE void mali_pp_enable_interrupts(struct mali_pp_core *core)
+{
+	mali_hw_core_register_write(&core->hw_core, MALI200_REG_ADDR_MGMT_INT_MASK, MALI200_REG_VAL_IRQ_MASK_USED);
+}
+
+MALI_STATIC_INLINE void mali_pp_write_addr_renderer_list(struct mali_pp_core *core,
+		struct mali_pp_job *job, u32 subjob)
+{
+	u32 addr = mali_pp_job_get_addr_frame(job, subjob);
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_FRAME, addr);
+}
+
+
+MALI_STATIC_INLINE void mali_pp_write_addr_stack(struct mali_pp_core *core, struct mali_pp_job *job)
+{
+	u32 addr = mali_pp_job_get_addr_stack(job, core->core_id);
+	mali_hw_core_register_write_relaxed(&core->hw_core, MALI200_REG_ADDR_STACK, addr);
+}
+
+#endif /* __MALI_PP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pp_job.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pp_job.c
@@ -0,0 +1,316 @@
+/*
+ * Copyright (C) 2011-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_pp.h"
+#include "mali_pp_job.h"
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_kernel_common.h"
+#include "mali_uk_types.h"
+#include "mali_executor.h"
+#if defined(CONFIG_DMA_SHARED_BUFFER) && !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+#include "linux/mali_memory_dma_buf.h"
+#endif
+#include "mali_memory_swap_alloc.h"
+#include "mali_scheduler.h"
+
+static u32 pp_counter_src0 = MALI_HW_CORE_NO_COUNTER;   /**< Performance counter 0, MALI_HW_CORE_NO_COUNTER for disabled */
+static u32 pp_counter_src1 = MALI_HW_CORE_NO_COUNTER;   /**< Performance counter 1, MALI_HW_CORE_NO_COUNTER for disabled */
+static _mali_osk_atomic_t pp_counter_per_sub_job_count; /**< Number of values in the two arrays which is != MALI_HW_CORE_NO_COUNTER */
+static u32 pp_counter_per_sub_job_src0[_MALI_PP_MAX_SUB_JOBS] = { MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER };
+static u32 pp_counter_per_sub_job_src1[_MALI_PP_MAX_SUB_JOBS] = { MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER, MALI_HW_CORE_NO_COUNTER };
+
+void mali_pp_job_initialize(void)
+{
+	_mali_osk_atomic_init(&pp_counter_per_sub_job_count, 0);
+}
+
+void mali_pp_job_terminate(void)
+{
+	_mali_osk_atomic_term(&pp_counter_per_sub_job_count);
+}
+
+struct mali_pp_job *mali_pp_job_create(struct mali_session_data *session,
+				       _mali_uk_pp_start_job_s __user *uargs, u32 id)
+{
+	struct mali_pp_job *job;
+	u32 perf_counter_flag;
+
+	job = _mali_osk_calloc(1, sizeof(struct mali_pp_job));
+	if (NULL != job) {
+
+		_mali_osk_list_init(&job->list);
+		_mali_osk_list_init(&job->session_fb_lookup_list);
+		_mali_osk_atomic_inc(&session->number_of_pp_jobs);
+
+		if (0 != _mali_osk_copy_from_user(&job->uargs, uargs, sizeof(_mali_uk_pp_start_job_s))) {
+			goto fail;
+		}
+
+		if (job->uargs.num_cores > _MALI_PP_MAX_SUB_JOBS) {
+			MALI_PRINT_ERROR(("Mali PP job: Too many sub jobs specified in job object\n"));
+			goto fail;
+		}
+
+		if (!mali_pp_job_use_no_notification(job)) {
+			job->finished_notification = _mali_osk_notification_create(_MALI_NOTIFICATION_PP_FINISHED, sizeof(_mali_uk_pp_job_finished_s));
+			if (NULL == job->finished_notification) goto fail;
+		}
+
+		perf_counter_flag = mali_pp_job_get_perf_counter_flag(job);
+
+		/* case when no counters came from user space
+		 * so pass the debugfs / DS-5 provided global ones to the job object */
+		if (!((perf_counter_flag & _MALI_PERFORMANCE_COUNTER_FLAG_SRC0_ENABLE) ||
+		      (perf_counter_flag & _MALI_PERFORMANCE_COUNTER_FLAG_SRC1_ENABLE))) {
+			u32 sub_job_count = _mali_osk_atomic_read(&pp_counter_per_sub_job_count);
+
+			/* These counters apply for all virtual jobs, and where no per sub job counter is specified */
+			job->uargs.perf_counter_src0 = pp_counter_src0;
+			job->uargs.perf_counter_src1 = pp_counter_src1;
+
+			/* We only copy the per sub job array if it is enabled with at least one counter */
+			if (0 < sub_job_count) {
+				job->perf_counter_per_sub_job_count = sub_job_count;
+				_mali_osk_memcpy(job->perf_counter_per_sub_job_src0, pp_counter_per_sub_job_src0, sizeof(pp_counter_per_sub_job_src0));
+				_mali_osk_memcpy(job->perf_counter_per_sub_job_src1, pp_counter_per_sub_job_src1, sizeof(pp_counter_per_sub_job_src1));
+			}
+		}
+
+		job->session = session;
+		job->id = id;
+
+		job->sub_jobs_num = job->uargs.num_cores ? job->uargs.num_cores : 1;
+		job->pid = _mali_osk_get_pid();
+		job->tid = _mali_osk_get_tid();
+
+		_mali_osk_atomic_init(&job->sub_jobs_completed, 0);
+		_mali_osk_atomic_init(&job->sub_job_errors, 0);
+		job->swap_status = MALI_NO_SWAP_IN;
+		job->user_notification = MALI_FALSE;
+		job->num_pp_cores_in_virtual = 0;
+
+		if (job->uargs.num_memory_cookies > session->allocation_mgr.mali_allocation_num) {
+			MALI_PRINT_ERROR(("Mali PP job: The number of memory cookies is invalid !\n"));
+			goto fail;
+		}
+
+		if (job->uargs.num_memory_cookies > 0) {
+			u32 size;
+			u32 __user *memory_cookies = (u32 __user *)(uintptr_t)job->uargs.memory_cookies;
+
+			size = sizeof(*memory_cookies) * (job->uargs.num_memory_cookies);
+
+			job->memory_cookies = _mali_osk_malloc(size);
+			if (NULL == job->memory_cookies) {
+				MALI_PRINT_ERROR(("Mali PP job: Failed to allocate %d bytes of memory cookies!\n", size));
+				goto fail;
+			}
+
+			if (0 != _mali_osk_copy_from_user(job->memory_cookies, memory_cookies, size)) {
+				MALI_PRINT_ERROR(("Mali PP job: Failed to copy %d bytes of memory cookies from user!\n", size));
+				goto fail;
+			}
+		}
+
+		if (_MALI_OSK_ERR_OK != mali_pp_job_check(job)) {
+			/* Not a valid job. */
+			goto fail;
+		}
+
+		mali_timeline_tracker_init(&job->tracker, MALI_TIMELINE_TRACKER_PP, NULL, job);
+		mali_timeline_fence_copy_uk_fence(&(job->tracker.fence), &(job->uargs.fence));
+
+		mali_mem_swap_in_pages(job);
+
+		return job;
+	}
+
+fail:
+	if (NULL != job) {
+		mali_pp_job_delete(job);
+	}
+
+	return NULL;
+}
+
+void mali_pp_job_delete(struct mali_pp_job *job)
+{
+	struct mali_session_data *session;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(&job->list));
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(&job->session_fb_lookup_list));
+
+	session = mali_pp_job_get_session(job);
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (NULL != job->memory_cookies) {
+#if defined(CONFIG_DMA_SHARED_BUFFER) && !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+		/* Unmap buffers attached to job */
+		mali_dma_buf_unmap_job(job);
+#endif
+		if (MALI_NO_SWAP_IN != job->swap_status) {
+			mali_mem_swap_out_pages(job);
+		}
+
+		_mali_osk_free(job->memory_cookies);
+	}
+
+	if (job->user_notification) {
+		mali_scheduler_return_pp_job_to_user(job,
+						     job->num_pp_cores_in_virtual);
+	}
+
+	if (NULL != job->finished_notification) {
+		_mali_osk_notification_delete(job->finished_notification);
+	}
+
+	_mali_osk_atomic_term(&job->sub_jobs_completed);
+	_mali_osk_atomic_term(&job->sub_job_errors);
+	_mali_osk_atomic_dec(&session->number_of_pp_jobs);
+	_mali_osk_free(job);
+
+	_mali_osk_wait_queue_wake_up(session->wait_queue);
+}
+
+void mali_pp_job_list_add(struct mali_pp_job *job, _mali_osk_list_t *list)
+{
+	struct mali_pp_job *iter;
+	struct mali_pp_job *tmp;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+
+	/* Find position in list/queue where job should be added. */
+	_MALI_OSK_LIST_FOREACHENTRY_REVERSE(iter, tmp, list,
+					    struct mali_pp_job, list) {
+		/* job should be started after iter if iter is in progress. */
+		if (0 < iter->sub_jobs_started) {
+			break;
+		}
+
+		/*
+		 * job should be started after iter if it has a higher
+		 * job id. A span is used to handle job id wrapping.
+		 */
+		if ((mali_pp_job_get_id(job) -
+		     mali_pp_job_get_id(iter)) <
+		    MALI_SCHEDULER_JOB_ID_SPAN) {
+			break;
+		}
+	}
+
+	_mali_osk_list_add(&job->list, &iter->list);
+}
+
+
+u32 mali_pp_job_get_perf_counter_src0(struct mali_pp_job *job, u32 sub_job)
+{
+	/* Virtual jobs always use the global job counter (or if there are per sub job counters at all) */
+	if (mali_pp_job_is_virtual(job) || 0 == job->perf_counter_per_sub_job_count) {
+		return job->uargs.perf_counter_src0;
+	}
+
+	/* Use per sub job counter if enabled... */
+	if (MALI_HW_CORE_NO_COUNTER != job->perf_counter_per_sub_job_src0[sub_job]) {
+		return job->perf_counter_per_sub_job_src0[sub_job];
+	}
+
+	/* ...else default to global job counter */
+	return job->uargs.perf_counter_src0;
+}
+
+u32 mali_pp_job_get_perf_counter_src1(struct mali_pp_job *job, u32 sub_job)
+{
+	/* Virtual jobs always use the global job counter (or if there are per sub job counters at all) */
+	if (mali_pp_job_is_virtual(job) || 0 == job->perf_counter_per_sub_job_count) {
+		/* Virtual jobs always use the global job counter */
+		return job->uargs.perf_counter_src1;
+	}
+
+	/* Use per sub job counter if enabled... */
+	if (MALI_HW_CORE_NO_COUNTER != job->perf_counter_per_sub_job_src1[sub_job]) {
+		return job->perf_counter_per_sub_job_src1[sub_job];
+	}
+
+	/* ...else default to global job counter */
+	return job->uargs.perf_counter_src1;
+}
+
+void mali_pp_job_set_pp_counter_global_src0(u32 counter)
+{
+	pp_counter_src0 = counter;
+}
+
+void mali_pp_job_set_pp_counter_global_src1(u32 counter)
+{
+	pp_counter_src1 = counter;
+}
+
+void mali_pp_job_set_pp_counter_sub_job_src0(u32 sub_job, u32 counter)
+{
+	MALI_DEBUG_ASSERT(sub_job < _MALI_PP_MAX_SUB_JOBS);
+
+	if (MALI_HW_CORE_NO_COUNTER == pp_counter_per_sub_job_src0[sub_job]) {
+		/* increment count since existing counter was disabled */
+		_mali_osk_atomic_inc(&pp_counter_per_sub_job_count);
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER == counter) {
+		/* decrement count since new counter is disabled */
+		_mali_osk_atomic_dec(&pp_counter_per_sub_job_count);
+	}
+
+	/* PS: A change from MALI_HW_CORE_NO_COUNTER to MALI_HW_CORE_NO_COUNTER will inc and dec, result will be 0 change */
+
+	pp_counter_per_sub_job_src0[sub_job] = counter;
+}
+
+void mali_pp_job_set_pp_counter_sub_job_src1(u32 sub_job, u32 counter)
+{
+	MALI_DEBUG_ASSERT(sub_job < _MALI_PP_MAX_SUB_JOBS);
+
+	if (MALI_HW_CORE_NO_COUNTER == pp_counter_per_sub_job_src1[sub_job]) {
+		/* increment count since existing counter was disabled */
+		_mali_osk_atomic_inc(&pp_counter_per_sub_job_count);
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER == counter) {
+		/* decrement count since new counter is disabled */
+		_mali_osk_atomic_dec(&pp_counter_per_sub_job_count);
+	}
+
+	/* PS: A change from MALI_HW_CORE_NO_COUNTER to MALI_HW_CORE_NO_COUNTER will inc and dec, result will be 0 change */
+
+	pp_counter_per_sub_job_src1[sub_job] = counter;
+}
+
+u32 mali_pp_job_get_pp_counter_global_src0(void)
+{
+	return pp_counter_src0;
+}
+
+u32 mali_pp_job_get_pp_counter_global_src1(void)
+{
+	return pp_counter_src1;
+}
+
+u32 mali_pp_job_get_pp_counter_sub_job_src0(u32 sub_job)
+{
+	MALI_DEBUG_ASSERT(sub_job < _MALI_PP_MAX_SUB_JOBS);
+	return pp_counter_per_sub_job_src0[sub_job];
+}
+
+u32 mali_pp_job_get_pp_counter_sub_job_src1(u32 sub_job)
+{
+	MALI_DEBUG_ASSERT(sub_job < _MALI_PP_MAX_SUB_JOBS);
+	return pp_counter_per_sub_job_src1[sub_job];
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_pp_job.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_pp_job.h
@@ -0,0 +1,594 @@
+/*
+ * Copyright (C) 2011-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PP_JOB_H__
+#define __MALI_PP_JOB_H__
+
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_uk_types.h"
+#include "mali_session.h"
+#include "mali_kernel_common.h"
+#include "regs/mali_200_regs.h"
+#include "mali_kernel_core.h"
+#include "mali_dlbu.h"
+#include "mali_timeline.h"
+#include "mali_scheduler.h"
+#include "mali_executor.h"
+#if defined(CONFIG_DMA_SHARED_BUFFER) && !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+#include "linux/mali_memory_dma_buf.h"
+#endif
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+#include "linux/mali_dma_fence.h"
+#endif
+
+typedef enum pp_job_status {
+	MALI_NO_SWAP_IN,
+	MALI_SWAP_IN_FAIL,
+	MALI_SWAP_IN_SUCC,
+} pp_job_status;
+
+/**
+ * This structure represents a PP job, including all sub jobs.
+ *
+ * The PP job object itself is not protected by any single lock,
+ * but relies on other locks instead (scheduler, executor and timeline lock).
+ * Think of the job object as moving between these sub systems through-out
+ * its lifetime. Different part of the PP job struct is used by different
+ * subsystems. Accessor functions ensure that correct lock is taken.
+ * Do NOT access any data members directly from outside this module!
+ */
+struct mali_pp_job {
+	/*
+	 * These members are typically only set at creation,
+	 * and only read later on.
+	 * They do not require any lock protection.
+	 */
+	_mali_uk_pp_start_job_s uargs;                     /**< Arguments from user space */
+	struct mali_session_data *session;                 /**< Session which submitted this job */
+	u32 pid;                                           /**< Process ID of submitting process */
+	u32 tid;                                           /**< Thread ID of submitting thread */
+	u32 id;                                            /**< Identifier for this job in kernel space (sequential numbering) */
+	u32 cache_order;                                   /**< Cache order used for L2 cache flushing (sequential numbering) */
+	struct mali_timeline_tracker tracker;              /**< Timeline tracker for this job */
+	_mali_osk_notification_t *finished_notification;   /**< Notification sent back to userspace on job complete */
+	u32 perf_counter_per_sub_job_count;                /**< Number of values in the two arrays which is != MALI_HW_CORE_NO_COUNTER */
+	u32 perf_counter_per_sub_job_src0[_MALI_PP_MAX_SUB_JOBS]; /**< Per sub job counters src0 */
+	u32 perf_counter_per_sub_job_src1[_MALI_PP_MAX_SUB_JOBS]; /**< Per sub job counters src1 */
+	u32 sub_jobs_num;                                  /**< Number of subjobs; set to 1 for Mali-450 if DLBU is used, otherwise equals number of PP cores */
+
+	pp_job_status swap_status;                         /**< Used to track each PP job swap status, if fail, we need to drop them in scheduler part */
+	mali_bool user_notification;                       /**< When we deferred delete PP job, we need to judge if we need to send job finish notification to user space */
+	u32 num_pp_cores_in_virtual;                       /**< How many PP cores we have when job finished */
+
+	/*
+	 * These members are used by both scheduler and executor.
+	 * They are "protected" by atomic operations.
+	 */
+	_mali_osk_atomic_t sub_jobs_completed;                            /**< Number of completed sub-jobs in this superjob */
+	_mali_osk_atomic_t sub_job_errors;                                /**< Bitfield with errors (errors for each single sub-job is or'ed together) */
+
+	/*
+	 * These members are used by scheduler, but only when no one else
+	 * knows about this job object but the working function.
+	 * No lock is thus needed for these.
+	 */
+	u32 *memory_cookies;                               /**< Memory cookies attached to job */
+
+	/*
+	 * These members are used by the scheduler,
+	 * protected by scheduler lock
+	 */
+	_mali_osk_list_t list;                             /**< Used to link jobs together in the scheduler queue */
+	_mali_osk_list_t session_fb_lookup_list;           /**< Used to link jobs together from the same frame builder in the session */
+
+	u32 sub_jobs_started;                              /**< Total number of sub-jobs started (always started in ascending order) */
+
+	/*
+	 * Set by executor/group on job completion, read by scheduler when
+	 * returning job to user. Hold executor lock when setting,
+	 * no lock needed when reading
+	 */
+	u32 perf_counter_value0[_MALI_PP_MAX_SUB_JOBS];    /**< Value of performance counter 0 (to be returned to user space), one for each sub job */
+	u32 perf_counter_value1[_MALI_PP_MAX_SUB_JOBS];    /**< Value of performance counter 1 (to be returned to user space), one for each sub job */
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	struct mali_dma_fence_context dma_fence_context; /**< The mali dma fence context to record dma fence waiters that this job wait for */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	struct dma_fence *rendered_dma_fence; /**< the new dma fence link to this job */
+#else
+	struct fence *rendered_dma_fence; /**< the new dma fence link to this job */
+#endif
+#endif
+};
+
+void mali_pp_job_initialize(void);
+void mali_pp_job_terminate(void);
+
+struct mali_pp_job *mali_pp_job_create(struct mali_session_data *session, _mali_uk_pp_start_job_s *uargs, u32 id);
+void mali_pp_job_delete(struct mali_pp_job *job);
+
+u32 mali_pp_job_get_perf_counter_src0(struct mali_pp_job *job, u32 sub_job);
+u32 mali_pp_job_get_perf_counter_src1(struct mali_pp_job *job, u32 sub_job);
+
+void mali_pp_job_set_pp_counter_global_src0(u32 counter);
+void mali_pp_job_set_pp_counter_global_src1(u32 counter);
+void mali_pp_job_set_pp_counter_sub_job_src0(u32 sub_job, u32 counter);
+void mali_pp_job_set_pp_counter_sub_job_src1(u32 sub_job, u32 counter);
+
+u32 mali_pp_job_get_pp_counter_global_src0(void);
+u32 mali_pp_job_get_pp_counter_global_src1(void);
+u32 mali_pp_job_get_pp_counter_sub_job_src0(u32 sub_job);
+u32 mali_pp_job_get_pp_counter_sub_job_src1(u32 sub_job);
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_id(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (NULL == job) ? 0 : job->id;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_set_cache_order(struct mali_pp_job *job,
+		u32 cache_order)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	job->cache_order = cache_order;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_cache_order(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (NULL == job) ? 0 : job->cache_order;
+}
+
+MALI_STATIC_INLINE u64 mali_pp_job_get_user_id(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.user_job_ptr;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_frame_builder_id(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.frame_builder_id;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_flush_id(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.flush_id;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_pid(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->pid;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_tid(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->tid;
+}
+
+MALI_STATIC_INLINE u32 *mali_pp_job_get_frame_registers(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.frame_registers;
+}
+
+MALI_STATIC_INLINE u32 *mali_pp_job_get_dlbu_registers(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.dlbu_registers;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_is_virtual(struct mali_pp_job *job)
+{
+#if (defined(CONFIG_MALI450) || defined(CONFIG_MALI470))
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (0 == job->uargs.num_cores) ? MALI_TRUE : MALI_FALSE;
+#else
+	return MALI_FALSE;
+#endif
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_addr_frame(struct mali_pp_job *job, u32 sub_job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	if (mali_pp_job_is_virtual(job)) {
+		return MALI_DLBU_VIRT_ADDR;
+	} else if (0 == sub_job) {
+		return job->uargs.frame_registers[MALI200_REG_ADDR_FRAME / sizeof(u32)];
+	} else if (sub_job < _MALI_PP_MAX_SUB_JOBS) {
+		return job->uargs.frame_registers_addr_frame[sub_job - 1];
+	}
+
+	return 0;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_addr_stack(struct mali_pp_job *job, u32 sub_job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	if (0 == sub_job) {
+		return job->uargs.frame_registers[MALI200_REG_ADDR_STACK / sizeof(u32)];
+	} else if (sub_job < _MALI_PP_MAX_SUB_JOBS) {
+		return job->uargs.frame_registers_addr_stack[sub_job - 1];
+	}
+
+	return 0;
+}
+
+void mali_pp_job_list_add(struct mali_pp_job *job, _mali_osk_list_t *list);
+
+MALI_STATIC_INLINE void mali_pp_job_list_addtail(struct mali_pp_job *job,
+		_mali_osk_list_t *list)
+{
+	_mali_osk_list_addtail(&job->list, list);
+}
+
+MALI_STATIC_INLINE void mali_pp_job_list_move(struct mali_pp_job *job,
+		_mali_osk_list_t *list)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	MALI_DEBUG_ASSERT(!_mali_osk_list_empty(&job->list));
+	_mali_osk_list_move(&job->list, list);
+}
+
+MALI_STATIC_INLINE void mali_pp_job_list_remove(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	_mali_osk_list_delinit(&job->list);
+}
+
+MALI_STATIC_INLINE u32 *mali_pp_job_get_wb0_registers(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.wb0_registers;
+}
+
+MALI_STATIC_INLINE u32 *mali_pp_job_get_wb1_registers(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.wb1_registers;
+}
+
+MALI_STATIC_INLINE u32 *mali_pp_job_get_wb2_registers(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.wb2_registers;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_wb0_source_addr(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.wb0_registers[MALI200_REG_ADDR_WB_SOURCE_ADDR / sizeof(u32)];
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_wb1_source_addr(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.wb1_registers[MALI200_REG_ADDR_WB_SOURCE_ADDR / sizeof(u32)];
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_wb2_source_addr(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.wb2_registers[MALI200_REG_ADDR_WB_SOURCE_ADDR / sizeof(u32)];
+}
+
+MALI_STATIC_INLINE void mali_pp_job_disable_wb0(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	job->uargs.wb0_registers[MALI200_REG_ADDR_WB_SOURCE_SELECT] = 0;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_disable_wb1(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	job->uargs.wb1_registers[MALI200_REG_ADDR_WB_SOURCE_SELECT] = 0;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_disable_wb2(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	job->uargs.wb2_registers[MALI200_REG_ADDR_WB_SOURCE_SELECT] = 0;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_all_writeback_unit_disabled(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	if (job->uargs.wb0_registers[MALI200_REG_ADDR_WB_SOURCE_SELECT] ||
+	    job->uargs.wb1_registers[MALI200_REG_ADDR_WB_SOURCE_SELECT] ||
+	    job->uargs.wb2_registers[MALI200_REG_ADDR_WB_SOURCE_SELECT]
+	   ) {
+		/* At least one output unit active */
+		return MALI_FALSE;
+	}
+
+	/* All outputs are disabled - we can abort the job */
+	return MALI_TRUE;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_fb_lookup_add(struct mali_pp_job *job)
+{
+	u32 fb_lookup_id;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+
+	fb_lookup_id = MALI_PP_JOB_FB_LOOKUP_LIST_MASK & job->uargs.frame_builder_id;
+
+	MALI_DEBUG_ASSERT(MALI_PP_JOB_FB_LOOKUP_LIST_SIZE > fb_lookup_id);
+
+	_mali_osk_list_addtail(&job->session_fb_lookup_list,
+			       &job->session->pp_job_fb_lookup_list[fb_lookup_id]);
+}
+
+MALI_STATIC_INLINE void mali_pp_job_fb_lookup_remove(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	_mali_osk_list_delinit(&job->session_fb_lookup_list);
+}
+
+MALI_STATIC_INLINE struct mali_session_data *mali_pp_job_get_session(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->session;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_has_started_sub_jobs(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	return (0 < job->sub_jobs_started) ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_has_unstarted_sub_jobs(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	return (job->sub_jobs_started < job->sub_jobs_num) ? MALI_TRUE : MALI_FALSE;
+}
+
+/* Function used when we are terminating a session with jobs. Return TRUE if it has a rendering job.
+   Makes sure that no new subjobs are started. */
+MALI_STATIC_INLINE void mali_pp_job_mark_unstarted_failed(struct mali_pp_job *job)
+{
+	u32 jobs_remaining;
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+
+	jobs_remaining = job->sub_jobs_num - job->sub_jobs_started;
+	job->sub_jobs_started += jobs_remaining;
+
+	/* Not the most optimal way, but this is only used in error cases */
+	for (i = 0; i < jobs_remaining; i++) {
+		_mali_osk_atomic_inc(&job->sub_jobs_completed);
+		_mali_osk_atomic_inc(&job->sub_job_errors);
+	}
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_is_complete(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (job->sub_jobs_num ==
+		_mali_osk_atomic_read(&job->sub_jobs_completed)) ?
+	       MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_first_unstarted_sub_job(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	return job->sub_jobs_started;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_sub_job_count(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->sub_jobs_num;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_unstarted_sub_job_count(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	MALI_DEBUG_ASSERT(job->sub_jobs_num >= job->sub_jobs_started);
+	return (job->sub_jobs_num - job->sub_jobs_started);
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_num_memory_cookies(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.num_memory_cookies;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_memory_cookie(
+	struct mali_pp_job *job, u32 index)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT(index < job->uargs.num_memory_cookies);
+	MALI_DEBUG_ASSERT_POINTER(job->memory_cookies);
+	return job->memory_cookies[index];
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_needs_dma_buf_mapping(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	if (0 < job->uargs.num_memory_cookies) {
+		return MALI_TRUE;
+	}
+
+	return MALI_FALSE;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_mark_sub_job_started(struct mali_pp_job *job, u32 sub_job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+
+	/* Assert that we are marking the "first unstarted sub job" as started */
+	MALI_DEBUG_ASSERT(job->sub_jobs_started == sub_job);
+
+	job->sub_jobs_started++;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_mark_sub_job_completed(struct mali_pp_job *job, mali_bool success)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	_mali_osk_atomic_inc(&job->sub_jobs_completed);
+	if (MALI_FALSE == success) {
+		_mali_osk_atomic_inc(&job->sub_job_errors);
+	}
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_was_success(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	if (0 == _mali_osk_atomic_read(&job->sub_job_errors)) {
+		return MALI_TRUE;
+	}
+	return MALI_FALSE;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_use_no_notification(
+	struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (job->uargs.flags & _MALI_PP_JOB_FLAG_NO_NOTIFICATION) ?
+	       MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_is_pilot_job(struct mali_pp_job *job)
+{
+	/*
+	 * A pilot job is currently identified as jobs which
+	 * require no callback notification.
+	 */
+	return mali_pp_job_use_no_notification(job);
+}
+
+MALI_STATIC_INLINE _mali_osk_notification_t *
+mali_pp_job_get_finished_notification(struct mali_pp_job *job)
+{
+	_mali_osk_notification_t *notification;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(job->finished_notification);
+
+	notification = job->finished_notification;
+	job->finished_notification = NULL;
+
+	return notification;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_is_window_surface(
+	struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (job->uargs.flags & _MALI_PP_JOB_FLAG_IS_WINDOW_SURFACE)
+	       ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE mali_bool mali_pp_job_is_protected_job(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (job->uargs.flags & _MALI_PP_JOB_FLAG_PROTECTED)
+	       ? MALI_TRUE : MALI_FALSE;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_perf_counter_flag(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->uargs.perf_counter_flag;
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_perf_counter_value0(struct mali_pp_job *job, u32 sub_job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->perf_counter_value0[sub_job];
+}
+
+MALI_STATIC_INLINE u32 mali_pp_job_get_perf_counter_value1(struct mali_pp_job *job, u32 sub_job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return job->perf_counter_value1[sub_job];
+}
+
+MALI_STATIC_INLINE void mali_pp_job_set_perf_counter_value0(struct mali_pp_job *job, u32 sub_job, u32 value)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	job->perf_counter_value0[sub_job] = value;
+}
+
+MALI_STATIC_INLINE void mali_pp_job_set_perf_counter_value1(struct mali_pp_job *job, u32 sub_job, u32 value)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_EXECUTOR_LOCK_HELD();
+	job->perf_counter_value1[sub_job] = value;
+}
+
+MALI_STATIC_INLINE _mali_osk_errcode_t mali_pp_job_check(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	if (mali_pp_job_is_virtual(job) && job->sub_jobs_num != 1) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+/**
+ * Returns MALI_TRUE if this job has more than two sub jobs and all sub jobs are unstarted.
+ *
+ * @param job Job to check.
+ * @return MALI_TRUE if job has more than two sub jobs and all sub jobs are unstarted, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_pp_job_is_large_and_unstarted(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	MALI_DEBUG_ASSERT(!mali_pp_job_is_virtual(job));
+
+	return (0 == job->sub_jobs_started && 2 < job->sub_jobs_num);
+}
+
+/**
+ * Get PP job's Timeline tracker.
+ *
+ * @param job PP job.
+ * @return Pointer to Timeline tracker for the job.
+ */
+MALI_STATIC_INLINE struct mali_timeline_tracker *mali_pp_job_get_tracker(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return &(job->tracker);
+}
+
+MALI_STATIC_INLINE u32 *mali_pp_job_get_timeline_point_ptr(
+	struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	return (u32 __user *)(uintptr_t)job->uargs.timeline_point_ptr;
+}
+
+
+#endif /* __MALI_PP_JOB_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_scheduler.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_scheduler.c
@@ -0,0 +1,1548 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_scheduler.h"
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_osk_profiling.h"
+#include "mali_kernel_utilization.h"
+#include "mali_timeline.h"
+#include "mali_gp_job.h"
+#include "mali_pp_job.h"
+#include "mali_executor.h"
+#include "mali_group.h"
+#include <linux/wait.h>
+#include <linux/sched.h>
+#include "mali_pm_metrics.h"
+
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+#include "mali_memory_dma_buf.h"
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+#include "mali_dma_fence.h"
+#include <linux/dma-buf.h>
+#endif
+#endif
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+#include <linux/sched.h>
+#include <trace/events/gpu.h>
+#endif
+/*
+ * ---------- static defines/constants ----------
+ */
+
+/*
+ * If dma_buf with map on demand is used, we defer job queue
+ * if in atomic context, since both might sleep.
+ */
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+#if !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+#define MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE 1
+#endif
+#endif
+
+
+/*
+ * ---------- global variables (exported due to inline functions) ----------
+ */
+
+/* Lock protecting this module */
+_mali_osk_spinlock_irq_t *mali_scheduler_lock_obj = NULL;
+
+/* Queue of jobs to be executed on the GP group */
+struct mali_scheduler_job_queue job_queue_gp;
+
+/* Queue of PP jobs */
+struct mali_scheduler_job_queue job_queue_pp;
+
+_mali_osk_atomic_t mali_job_id_autonumber;
+_mali_osk_atomic_t mali_job_cache_order_autonumber;
+/*
+ * ---------- static variables ----------
+ */
+
+_mali_osk_wq_work_t *scheduler_wq_pp_job_delete = NULL;
+_mali_osk_spinlock_irq_t *scheduler_pp_job_delete_lock = NULL;
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(scheduler_pp_job_deletion_queue);
+
+#if defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE)
+static _mali_osk_wq_work_t *scheduler_wq_pp_job_queue = NULL;
+static _mali_osk_spinlock_irq_t *scheduler_pp_job_queue_lock = NULL;
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(scheduler_pp_job_queue_list);
+#endif
+
+/*
+ * ---------- Forward declaration of static functions ----------
+ */
+
+static mali_timeline_point mali_scheduler_submit_gp_job(
+	struct mali_session_data *session, struct mali_gp_job *job);
+static _mali_osk_errcode_t mali_scheduler_submit_pp_job(
+	struct mali_session_data *session, struct mali_pp_job *job, mali_timeline_point *point);
+
+static mali_bool mali_scheduler_queue_gp_job(struct mali_gp_job *job);
+static mali_bool mali_scheduler_queue_pp_job(struct mali_pp_job *job);
+
+static void mali_scheduler_return_gp_job_to_user(struct mali_gp_job *job,
+		mali_bool success);
+
+static void mali_scheduler_deferred_pp_job_delete(struct mali_pp_job *job);
+void mali_scheduler_do_pp_job_delete(void *arg);
+
+#if defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE)
+static void mali_scheduler_deferred_pp_job_queue(struct mali_pp_job *job);
+static void mali_scheduler_do_pp_job_queue(void *arg);
+#endif /* defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE) */
+
+/*
+ * ---------- Actual implementation ----------
+ */
+
+_mali_osk_errcode_t mali_scheduler_initialize(void)
+{
+	_mali_osk_atomic_init(&mali_job_id_autonumber, 0);
+	_mali_osk_atomic_init(&mali_job_cache_order_autonumber, 0);
+
+	_MALI_OSK_INIT_LIST_HEAD(&job_queue_gp.normal_pri);
+	_MALI_OSK_INIT_LIST_HEAD(&job_queue_gp.high_pri);
+	job_queue_gp.depth = 0;
+	job_queue_gp.big_job_num = 0;
+
+	_MALI_OSK_INIT_LIST_HEAD(&job_queue_pp.normal_pri);
+	_MALI_OSK_INIT_LIST_HEAD(&job_queue_pp.high_pri);
+	job_queue_pp.depth = 0;
+	job_queue_pp.big_job_num = 0;
+
+	mali_scheduler_lock_obj = _mali_osk_spinlock_irq_init(
+					  _MALI_OSK_LOCKFLAG_ORDERED,
+					  _MALI_OSK_LOCK_ORDER_SCHEDULER);
+	if (NULL == mali_scheduler_lock_obj) {
+		mali_scheduler_terminate();
+	}
+
+	scheduler_wq_pp_job_delete = _mali_osk_wq_create_work(
+					     mali_scheduler_do_pp_job_delete, NULL);
+	if (NULL == scheduler_wq_pp_job_delete) {
+		mali_scheduler_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	scheduler_pp_job_delete_lock = _mali_osk_spinlock_irq_init(
+					       _MALI_OSK_LOCKFLAG_ORDERED,
+					       _MALI_OSK_LOCK_ORDER_SCHEDULER_DEFERRED);
+	if (NULL == scheduler_pp_job_delete_lock) {
+		mali_scheduler_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+#if defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE)
+	scheduler_wq_pp_job_queue = _mali_osk_wq_create_work(
+					    mali_scheduler_do_pp_job_queue, NULL);
+	if (NULL == scheduler_wq_pp_job_queue) {
+		mali_scheduler_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	scheduler_pp_job_queue_lock = _mali_osk_spinlock_irq_init(
+					      _MALI_OSK_LOCKFLAG_ORDERED,
+					      _MALI_OSK_LOCK_ORDER_SCHEDULER_DEFERRED);
+	if (NULL == scheduler_pp_job_queue_lock) {
+		mali_scheduler_terminate();
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif /* defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE) */
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_scheduler_terminate(void)
+{
+#if defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE)
+	if (NULL != scheduler_pp_job_queue_lock) {
+		_mali_osk_spinlock_irq_term(scheduler_pp_job_queue_lock);
+		scheduler_pp_job_queue_lock = NULL;
+	}
+
+	if (NULL != scheduler_wq_pp_job_queue) {
+		_mali_osk_wq_delete_work(scheduler_wq_pp_job_queue);
+		scheduler_wq_pp_job_queue = NULL;
+	}
+#endif /* defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE) */
+
+	if (NULL != scheduler_pp_job_delete_lock) {
+		_mali_osk_spinlock_irq_term(scheduler_pp_job_delete_lock);
+		scheduler_pp_job_delete_lock = NULL;
+	}
+
+	if (NULL != scheduler_wq_pp_job_delete) {
+		_mali_osk_wq_delete_work(scheduler_wq_pp_job_delete);
+		scheduler_wq_pp_job_delete = NULL;
+	}
+
+	if (NULL != mali_scheduler_lock_obj) {
+		_mali_osk_spinlock_irq_term(mali_scheduler_lock_obj);
+		mali_scheduler_lock_obj = NULL;
+	}
+
+	_mali_osk_atomic_term(&mali_job_cache_order_autonumber);
+	_mali_osk_atomic_term(&mali_job_id_autonumber);
+}
+
+u32 mali_scheduler_job_physical_head_count(mali_bool gpu_mode_is_secure)
+{
+	/*
+	 * Count how many physical sub jobs are present from the head of queue
+	 * until the first virtual job is present.
+	 * Early out when we have reached maximum number of PP cores (8)
+	 */
+	u32 count = 0;
+	struct mali_pp_job *job;
+	struct mali_pp_job *temp;
+
+	/* Check for partially started normal pri jobs */
+	if (!_mali_osk_list_empty(&job_queue_pp.normal_pri)) {
+		MALI_DEBUG_ASSERT(0 < job_queue_pp.depth);
+
+		job = _MALI_OSK_LIST_ENTRY(job_queue_pp.normal_pri.next,
+					   struct mali_pp_job, list);
+
+		MALI_DEBUG_ASSERT_POINTER(job);
+
+		if (MALI_TRUE == mali_pp_job_has_started_sub_jobs(job)) {
+			/*
+			 * Remember; virtual jobs can't be queued and started
+			 * at the same time, so this must be a physical job
+			 */
+			if ((MALI_FALSE  == gpu_mode_is_secure && MALI_FALSE == mali_pp_job_is_protected_job(job))
+			    || (MALI_TRUE  == gpu_mode_is_secure && MALI_TRUE == mali_pp_job_is_protected_job(job))) {
+
+				count += mali_pp_job_unstarted_sub_job_count(job);
+				if (MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS <= count) {
+					return MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS;
+				}
+			}
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, temp, &job_queue_pp.high_pri,
+				    struct mali_pp_job, list) {
+		if ((MALI_FALSE == mali_pp_job_is_virtual(job))
+		    && ((MALI_FALSE  == gpu_mode_is_secure && MALI_FALSE == mali_pp_job_is_protected_job(job))
+			|| (MALI_TRUE  == gpu_mode_is_secure && MALI_TRUE == mali_pp_job_is_protected_job(job)))) {
+
+			count += mali_pp_job_unstarted_sub_job_count(job);
+			if (MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS <= count) {
+				return MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS;
+			}
+		} else {
+			/* Came across a virtual job, so stop counting */
+			return count;
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, temp, &job_queue_pp.normal_pri,
+				    struct mali_pp_job, list) {
+		if ((MALI_FALSE == mali_pp_job_is_virtual(job))
+		    && (MALI_FALSE == mali_pp_job_has_started_sub_jobs(job))
+		    && ((MALI_FALSE  == gpu_mode_is_secure && MALI_FALSE == mali_pp_job_is_protected_job(job))
+			|| (MALI_TRUE  == gpu_mode_is_secure && MALI_TRUE == mali_pp_job_is_protected_job(job)))) {
+
+			count += mali_pp_job_unstarted_sub_job_count(job);
+			if (MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS <= count) {
+				return MALI_MAX_NUMBER_OF_PHYSICAL_PP_GROUPS;
+			}
+		} else {
+			/* Came across a virtual job, so stop counting */
+			return count;
+		}
+	}
+	return count;
+}
+
+struct mali_pp_job *mali_scheduler_job_pp_next(void)
+{
+	struct mali_pp_job *job;
+	struct mali_pp_job *temp;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+
+	/* Check for partially started normal pri jobs */
+	if (!_mali_osk_list_empty(&job_queue_pp.normal_pri)) {
+		MALI_DEBUG_ASSERT(0 < job_queue_pp.depth);
+
+		job = _MALI_OSK_LIST_ENTRY(job_queue_pp.normal_pri.next,
+					   struct mali_pp_job, list);
+
+		MALI_DEBUG_ASSERT_POINTER(job);
+
+		if (MALI_TRUE == mali_pp_job_has_started_sub_jobs(job)) {
+			return job;
+		}
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, temp, &job_queue_pp.high_pri,
+				    struct mali_pp_job, list) {
+		return job;
+	}
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, temp, &job_queue_pp.normal_pri,
+				    struct mali_pp_job, list) {
+		return job;
+	}
+
+	return NULL;
+}
+
+mali_bool mali_scheduler_job_next_is_virtual(void)
+{
+	struct mali_pp_job *job;
+
+	job = mali_scheduler_job_pp_virtual_peek();
+	if (NULL != job) {
+		MALI_DEBUG_ASSERT(mali_pp_job_is_virtual(job));
+
+		return MALI_TRUE;
+	}
+
+	return MALI_FALSE;
+}
+
+struct mali_gp_job *mali_scheduler_job_gp_get(void)
+{
+	_mali_osk_list_t *queue;
+	struct mali_gp_job *job = NULL;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+	MALI_DEBUG_ASSERT(0 < job_queue_gp.depth);
+	MALI_DEBUG_ASSERT(job_queue_gp.big_job_num <= job_queue_gp.depth);
+
+	if (!_mali_osk_list_empty(&job_queue_gp.high_pri)) {
+		queue = &job_queue_gp.high_pri;
+	} else {
+		queue = &job_queue_gp.normal_pri;
+		MALI_DEBUG_ASSERT(!_mali_osk_list_empty(queue));
+	}
+
+	job = _MALI_OSK_LIST_ENTRY(queue->next, struct mali_gp_job, list);
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	mali_gp_job_list_remove(job);
+	job_queue_gp.depth--;
+	if (job->big_job) {
+		job_queue_gp.big_job_num --;
+		if (job_queue_gp.big_job_num < MALI_MAX_PENDING_BIG_JOB) {
+			/* wake up process */
+			wait_queue_head_t *queue = mali_session_get_wait_queue();
+			wake_up(queue);
+		}
+	}
+	return job;
+}
+
+struct mali_pp_job *mali_scheduler_job_pp_physical_peek(void)
+{
+	struct mali_pp_job *job = NULL;
+	struct mali_pp_job *tmp_job = NULL;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+
+	/*
+	 * For PP jobs we favour partially started jobs in normal
+	 * priority queue over unstarted jobs in high priority queue
+	 */
+
+	if (!_mali_osk_list_empty(&job_queue_pp.normal_pri)) {
+		MALI_DEBUG_ASSERT(0 < job_queue_pp.depth);
+
+		tmp_job = _MALI_OSK_LIST_ENTRY(job_queue_pp.normal_pri.next,
+					       struct mali_pp_job, list);
+		MALI_DEBUG_ASSERT(NULL != tmp_job);
+
+		if (MALI_FALSE == mali_pp_job_is_virtual(tmp_job)) {
+			job = tmp_job;
+		}
+	}
+
+	if (NULL == job ||
+	    MALI_FALSE == mali_pp_job_has_started_sub_jobs(job)) {
+		/*
+		 * There isn't a partially started job in normal queue, so
+		 * look in high priority queue.
+		 */
+		if (!_mali_osk_list_empty(&job_queue_pp.high_pri)) {
+			MALI_DEBUG_ASSERT(0 < job_queue_pp.depth);
+
+			tmp_job = _MALI_OSK_LIST_ENTRY(job_queue_pp.high_pri.next,
+						       struct mali_pp_job, list);
+			MALI_DEBUG_ASSERT(NULL != tmp_job);
+
+			if (MALI_FALSE == mali_pp_job_is_virtual(tmp_job)) {
+				job = tmp_job;
+			}
+		}
+	}
+
+	return job;
+}
+
+struct mali_pp_job *mali_scheduler_job_pp_virtual_peek(void)
+{
+	struct mali_pp_job *job = NULL;
+	struct mali_pp_job *tmp_job = NULL;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+
+	if (!_mali_osk_list_empty(&job_queue_pp.high_pri)) {
+		MALI_DEBUG_ASSERT(0 < job_queue_pp.depth);
+
+		tmp_job = _MALI_OSK_LIST_ENTRY(job_queue_pp.high_pri.next,
+					       struct mali_pp_job, list);
+
+		if (MALI_TRUE == mali_pp_job_is_virtual(tmp_job)) {
+			job = tmp_job;
+		}
+	}
+
+	if (NULL == job) {
+		if (!_mali_osk_list_empty(&job_queue_pp.normal_pri)) {
+			MALI_DEBUG_ASSERT(0 < job_queue_pp.depth);
+
+			tmp_job = _MALI_OSK_LIST_ENTRY(job_queue_pp.normal_pri.next,
+						       struct mali_pp_job, list);
+
+			if (MALI_TRUE == mali_pp_job_is_virtual(tmp_job)) {
+				job = tmp_job;
+			}
+		}
+	}
+
+	return job;
+}
+
+struct mali_pp_job *mali_scheduler_job_pp_physical_get(u32 *sub_job)
+{
+	struct mali_pp_job *job = mali_scheduler_job_pp_physical_peek();
+
+	MALI_DEBUG_ASSERT(MALI_FALSE == mali_pp_job_is_virtual(job));
+
+	if (NULL != job) {
+		*sub_job = mali_pp_job_get_first_unstarted_sub_job(job);
+
+		mali_pp_job_mark_sub_job_started(job, *sub_job);
+		if (MALI_FALSE == mali_pp_job_has_unstarted_sub_jobs(job)) {
+			/* Remove from queue when last sub job has been retrieved */
+			mali_pp_job_list_remove(job);
+		}
+
+		job_queue_pp.depth--;
+
+		/*
+		 * Job about to start so it is no longer be
+		 * possible to discard WB
+		 */
+		mali_pp_job_fb_lookup_remove(job);
+	}
+
+	return job;
+}
+
+struct mali_pp_job *mali_scheduler_job_pp_virtual_get(void)
+{
+	struct mali_pp_job *job = mali_scheduler_job_pp_virtual_peek();
+
+	MALI_DEBUG_ASSERT(MALI_TRUE == mali_pp_job_is_virtual(job));
+
+	if (NULL != job) {
+		MALI_DEBUG_ASSERT(0 ==
+				  mali_pp_job_get_first_unstarted_sub_job(job));
+		MALI_DEBUG_ASSERT(1 ==
+				  mali_pp_job_get_sub_job_count(job));
+
+		mali_pp_job_mark_sub_job_started(job, 0);
+
+		mali_pp_job_list_remove(job);
+
+		job_queue_pp.depth--;
+
+		/*
+		 * Job about to start so it is no longer be
+		 * possible to discard WB
+		 */
+		mali_pp_job_fb_lookup_remove(job);
+	}
+
+	return job;
+}
+
+mali_scheduler_mask mali_scheduler_activate_gp_job(struct mali_gp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	MALI_DEBUG_PRINT(4, ("Mali GP scheduler: Timeline activation for job %u (0x%08X).\n",
+			     mali_gp_job_get_id(job), job));
+
+	mali_scheduler_lock();
+
+	if (!mali_scheduler_queue_gp_job(job)) {
+		/* Failed to enqueue job, release job (with error) */
+
+		mali_scheduler_unlock();
+
+		mali_timeline_tracker_release(mali_gp_job_get_tracker(job));
+		mali_gp_job_signal_pp_tracker(job, MALI_FALSE);
+
+		/* This will notify user space and close the job object */
+		mali_scheduler_complete_gp_job(job, MALI_FALSE,
+					       MALI_TRUE, MALI_FALSE);
+
+		return MALI_SCHEDULER_MASK_EMPTY;
+	}
+
+	mali_scheduler_unlock();
+
+	return MALI_SCHEDULER_MASK_GP;
+}
+
+mali_scheduler_mask mali_scheduler_activate_pp_job(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	MALI_DEBUG_PRINT(4, ("Mali PP scheduler: Timeline activation for job %u (0x%08X).\n",
+			     mali_pp_job_get_id(job), job));
+
+	if (MALI_TRUE == mali_timeline_tracker_activation_error(
+		    mali_pp_job_get_tracker(job))) {
+		MALI_DEBUG_PRINT(3, ("Mali PP scheduler: Job %u (0x%08X) activated with error, aborting.\n",
+				     mali_pp_job_get_id(job), job));
+
+		mali_scheduler_lock();
+		mali_pp_job_fb_lookup_remove(job);
+		mali_pp_job_mark_unstarted_failed(job);
+		mali_scheduler_unlock();
+
+		mali_timeline_tracker_release(mali_pp_job_get_tracker(job));
+
+		/* This will notify user space and close the job object */
+		mali_scheduler_complete_pp_job(job, 0, MALI_TRUE, MALI_FALSE);
+
+		return MALI_SCHEDULER_MASK_EMPTY;
+	}
+
+#if defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE)
+	if (mali_pp_job_needs_dma_buf_mapping(job)) {
+		mali_scheduler_deferred_pp_job_queue(job);
+		return MALI_SCHEDULER_MASK_EMPTY;
+	}
+#endif /* defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE) */
+
+	mali_scheduler_lock();
+
+	if (!mali_scheduler_queue_pp_job(job)) {
+		/* Failed to enqueue job, release job (with error) */
+		mali_pp_job_fb_lookup_remove(job);
+		mali_pp_job_mark_unstarted_failed(job);
+		mali_scheduler_unlock();
+
+		mali_timeline_tracker_release(mali_pp_job_get_tracker(job));
+
+		/* This will notify user space and close the job object */
+		mali_scheduler_complete_pp_job(job, 0, MALI_TRUE, MALI_FALSE);
+
+		return MALI_SCHEDULER_MASK_EMPTY;
+	}
+
+	mali_scheduler_unlock();
+	return MALI_SCHEDULER_MASK_PP;
+}
+
+void mali_scheduler_complete_gp_job(struct mali_gp_job *job,
+				    mali_bool success,
+				    mali_bool user_notification,
+				    mali_bool dequeued)
+{
+	if (user_notification) {
+		mali_scheduler_return_gp_job_to_user(job, success);
+	}
+
+	if (dequeued) {
+		_mali_osk_pm_dev_ref_put();
+
+		if (mali_utilization_enabled()) {
+			mali_utilization_gp_end();
+		}
+		mali_pm_record_gpu_idle(MALI_TRUE);
+	}
+
+	mali_gp_job_delete(job);
+}
+
+void mali_scheduler_complete_pp_job(struct mali_pp_job *job,
+				    u32 num_cores_in_virtual,
+				    mali_bool user_notification,
+				    mali_bool dequeued)
+{
+	job->user_notification = user_notification;
+	job->num_pp_cores_in_virtual = num_cores_in_virtual;
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	if (NULL != job->rendered_dma_fence)
+		mali_dma_fence_signal_and_put(&job->rendered_dma_fence);
+#endif
+
+	if (dequeued) {
+#if defined(CONFIG_MALI_DVFS)
+		if (mali_pp_job_is_window_surface(job)) {
+			struct mali_session_data *session;
+			session = mali_pp_job_get_session(job);
+			mali_session_inc_num_window_jobs(session);
+		}
+#endif
+		_mali_osk_pm_dev_ref_put();
+
+		if (mali_utilization_enabled()) {
+			mali_utilization_pp_end();
+		}
+		mali_pm_record_gpu_idle(MALI_FALSE);
+	}
+
+	/* With ZRAM feature enabled, all pp jobs will be force to use deferred delete. */
+	mali_scheduler_deferred_pp_job_delete(job);
+}
+
+void mali_scheduler_abort_session(struct mali_session_data *session)
+{
+	struct mali_gp_job *gp_job;
+	struct mali_gp_job *gp_tmp;
+	struct mali_pp_job *pp_job;
+	struct mali_pp_job *pp_tmp;
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(removed_jobs_gp);
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(removed_jobs_pp);
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT(session->is_aborting);
+
+	MALI_DEBUG_PRINT(3, ("Mali scheduler: Aborting all queued jobs from session 0x%08X.\n",
+			     session));
+
+	mali_scheduler_lock();
+
+	/* Remove from GP normal priority queue */
+	_MALI_OSK_LIST_FOREACHENTRY(gp_job, gp_tmp, &job_queue_gp.normal_pri,
+				    struct mali_gp_job, list) {
+		if (mali_gp_job_get_session(gp_job) == session) {
+			mali_gp_job_list_move(gp_job, &removed_jobs_gp);
+			job_queue_gp.depth--;
+			job_queue_gp.big_job_num -= gp_job->big_job ? 1 : 0;
+		}
+	}
+
+	/* Remove from GP high priority queue */
+	_MALI_OSK_LIST_FOREACHENTRY(gp_job, gp_tmp, &job_queue_gp.high_pri,
+				    struct mali_gp_job, list) {
+		if (mali_gp_job_get_session(gp_job) == session) {
+			mali_gp_job_list_move(gp_job, &removed_jobs_gp);
+			job_queue_gp.depth--;
+			job_queue_gp.big_job_num -= gp_job->big_job ? 1 : 0;
+		}
+	}
+
+	/* Remove from PP normal priority queue */
+	_MALI_OSK_LIST_FOREACHENTRY(pp_job, pp_tmp,
+				    &job_queue_pp.normal_pri,
+				    struct mali_pp_job, list) {
+		if (mali_pp_job_get_session(pp_job) == session) {
+			mali_pp_job_fb_lookup_remove(pp_job);
+
+			job_queue_pp.depth -=
+				mali_pp_job_unstarted_sub_job_count(
+					pp_job);
+			mali_pp_job_mark_unstarted_failed(pp_job);
+
+			if (MALI_FALSE == mali_pp_job_has_unstarted_sub_jobs(pp_job)) {
+				if (mali_pp_job_is_complete(pp_job)) {
+					mali_pp_job_list_move(pp_job,
+							      &removed_jobs_pp);
+				} else {
+					mali_pp_job_list_remove(pp_job);
+				}
+			}
+		}
+	}
+
+	/* Remove from PP high priority queue */
+	_MALI_OSK_LIST_FOREACHENTRY(pp_job, pp_tmp,
+				    &job_queue_pp.high_pri,
+				    struct mali_pp_job, list) {
+		if (mali_pp_job_get_session(pp_job) == session) {
+			mali_pp_job_fb_lookup_remove(pp_job);
+
+			job_queue_pp.depth -=
+				mali_pp_job_unstarted_sub_job_count(
+					pp_job);
+			mali_pp_job_mark_unstarted_failed(pp_job);
+
+			if (MALI_FALSE == mali_pp_job_has_unstarted_sub_jobs(pp_job)) {
+				if (mali_pp_job_is_complete(pp_job)) {
+					mali_pp_job_list_move(pp_job,
+							      &removed_jobs_pp);
+				} else {
+					mali_pp_job_list_remove(pp_job);
+				}
+			}
+		}
+	}
+
+	/*
+	 * Release scheduler lock so we can release trackers
+	 * (which will potentially queue new jobs)
+	 */
+	mali_scheduler_unlock();
+
+	/* Release and complete all (non-running) found GP jobs  */
+	_MALI_OSK_LIST_FOREACHENTRY(gp_job, gp_tmp, &removed_jobs_gp,
+				    struct mali_gp_job, list) {
+		mali_timeline_tracker_release(mali_gp_job_get_tracker(gp_job));
+		mali_gp_job_signal_pp_tracker(gp_job, MALI_FALSE);
+		_mali_osk_list_delinit(&gp_job->list);
+		mali_scheduler_complete_gp_job(gp_job,
+					       MALI_FALSE, MALI_TRUE, MALI_TRUE);
+	}
+
+	/* Release and complete non-running PP jobs */
+	_MALI_OSK_LIST_FOREACHENTRY(pp_job, pp_tmp, &removed_jobs_pp,
+				    struct mali_pp_job, list) {
+		mali_timeline_tracker_release(mali_pp_job_get_tracker(pp_job));
+		_mali_osk_list_delinit(&pp_job->list);
+		mali_scheduler_complete_pp_job(pp_job, 0,
+					       MALI_TRUE, MALI_TRUE);
+	}
+}
+
+_mali_osk_errcode_t _mali_ukk_gp_start_job(void *ctx,
+		_mali_uk_gp_start_job_s *uargs)
+{
+	struct mali_session_data *session;
+	struct mali_gp_job *job;
+	mali_timeline_point point;
+	u32 __user *point_ptr = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(uargs);
+	MALI_DEBUG_ASSERT_POINTER(ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)ctx;
+
+	job = mali_gp_job_create(session, uargs, mali_scheduler_get_new_id(),
+				 NULL);
+	if (NULL == job) {
+		MALI_PRINT_ERROR(("Failed to create GP job.\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	point_ptr = (u32 __user *)(uintptr_t)mali_gp_job_get_timeline_point_ptr(job);
+
+	point = mali_scheduler_submit_gp_job(session, job);
+
+	if (0 != _mali_osk_put_user(((u32) point), point_ptr)) {
+		/*
+		 * Let user space know that something failed
+		 * after the job was started.
+		 */
+		return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_pp_start_job(void *ctx,
+		_mali_uk_pp_start_job_s *uargs)
+{
+	_mali_osk_errcode_t ret;
+	struct mali_session_data *session;
+	struct mali_pp_job *job;
+	mali_timeline_point point;
+	u32 __user *point_ptr = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(uargs);
+	MALI_DEBUG_ASSERT_POINTER(ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)ctx;
+
+	job = mali_pp_job_create(session, uargs, mali_scheduler_get_new_id());
+	if (NULL == job) {
+		MALI_PRINT_ERROR(("Failed to create PP job.\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	point_ptr = (u32 __user *)(uintptr_t)mali_pp_job_get_timeline_point_ptr(job);
+
+	/* Submit PP job. */
+	ret = mali_scheduler_submit_pp_job(session, job, &point);
+	job = NULL;
+
+	if (_MALI_OSK_ERR_OK == ret) {
+		if (0 != _mali_osk_put_user(((u32) point), point_ptr)) {
+			/*
+			* Let user space know that something failed
+			* after the jobs were started.
+			*/
+			return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+		}
+	}
+
+	return ret;
+}
+
+_mali_osk_errcode_t _mali_ukk_pp_and_gp_start_job(void *ctx,
+		_mali_uk_pp_and_gp_start_job_s *uargs)
+{
+	_mali_osk_errcode_t ret;
+	struct mali_session_data *session;
+	_mali_uk_pp_and_gp_start_job_s kargs;
+	struct mali_pp_job *pp_job;
+	struct mali_gp_job *gp_job;
+	u32 __user *point_ptr = NULL;
+	mali_timeline_point point;
+	_mali_uk_pp_start_job_s __user *pp_args;
+	_mali_uk_gp_start_job_s __user *gp_args;
+
+	MALI_DEBUG_ASSERT_POINTER(ctx);
+	MALI_DEBUG_ASSERT_POINTER(uargs);
+
+	session = (struct mali_session_data *) ctx;
+
+	if (0 != _mali_osk_copy_from_user(&kargs, uargs,
+					  sizeof(_mali_uk_pp_and_gp_start_job_s))) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	pp_args = (_mali_uk_pp_start_job_s __user *)(uintptr_t)kargs.pp_args;
+	gp_args = (_mali_uk_gp_start_job_s __user *)(uintptr_t)kargs.gp_args;
+
+	pp_job = mali_pp_job_create(session, pp_args,
+				    mali_scheduler_get_new_id());
+	if (NULL == pp_job) {
+		MALI_PRINT_ERROR(("Failed to create PP job.\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	gp_job = mali_gp_job_create(session, gp_args,
+				    mali_scheduler_get_new_id(),
+				    mali_pp_job_get_tracker(pp_job));
+	if (NULL == gp_job) {
+		MALI_PRINT_ERROR(("Failed to create GP job.\n"));
+		mali_pp_job_delete(pp_job);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	point_ptr = (u32 __user *)(uintptr_t)mali_pp_job_get_timeline_point_ptr(pp_job);
+
+	/* Submit GP job. */
+	mali_scheduler_submit_gp_job(session, gp_job);
+	gp_job = NULL;
+
+	/* Submit PP job. */
+	ret = mali_scheduler_submit_pp_job(session, pp_job, &point);
+	pp_job = NULL;
+
+	if (_MALI_OSK_ERR_OK == ret) {
+		if (0 != _mali_osk_put_user(((u32) point), point_ptr)) {
+			/*
+			* Let user space know that something failed
+			* after the jobs were started.
+			*/
+			return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+		}
+	}
+
+	return ret;
+}
+
+void _mali_ukk_pp_job_disable_wb(_mali_uk_pp_disable_wb_s *args)
+{
+	struct mali_session_data *session;
+	struct mali_pp_job *job;
+	struct mali_pp_job *tmp;
+	u32 fb_lookup_id;
+
+	MALI_DEBUG_ASSERT_POINTER(args);
+	MALI_DEBUG_ASSERT(NULL != (void *)(uintptr_t)args->ctx);
+
+	session = (struct mali_session_data *)(uintptr_t)args->ctx;
+
+	fb_lookup_id = args->fb_id & MALI_PP_JOB_FB_LOOKUP_LIST_MASK;
+
+	mali_scheduler_lock();
+
+	/* Iterate over all jobs for given frame builder_id. */
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp,
+				    &session->pp_job_fb_lookup_list[fb_lookup_id],
+				    struct mali_pp_job, session_fb_lookup_list) {
+		MALI_DEBUG_CODE(u32 disable_mask = 0);
+
+		if (mali_pp_job_get_frame_builder_id(job) !=
+		    (u32) args->fb_id) {
+			MALI_DEBUG_PRINT(4, ("Mali PP scheduler: Disable WB mismatching FB.\n"));
+			continue;
+		}
+
+		MALI_DEBUG_CODE(disable_mask |= 0xD << (4 * 3));
+
+		if (mali_pp_job_get_wb0_source_addr(job) == args->wb0_memory) {
+			MALI_DEBUG_CODE(disable_mask |= 0x1 << (4 * 1));
+			mali_pp_job_disable_wb0(job);
+		}
+
+		if (mali_pp_job_get_wb1_source_addr(job) == args->wb1_memory) {
+			MALI_DEBUG_CODE(disable_mask |= 0x2 << (4 * 2));
+			mali_pp_job_disable_wb1(job);
+		}
+
+		if (mali_pp_job_get_wb2_source_addr(job) == args->wb2_memory) {
+			MALI_DEBUG_CODE(disable_mask |= 0x3 << (4 * 3));
+			mali_pp_job_disable_wb2(job);
+		}
+		MALI_DEBUG_PRINT(3, ("Mali PP scheduler: Disable WB: 0x%X.\n",
+				     disable_mask));
+	}
+
+	mali_scheduler_unlock();
+}
+
+#if MALI_STATE_TRACKING
+u32 mali_scheduler_dump_state(char *buf, u32 size)
+{
+	int n = 0;
+
+	n += _mali_osk_snprintf(buf + n, size - n, "GP queues\n");
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tQueue depth: %u\n", job_queue_gp.depth);
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tNormal priority queue is %s\n",
+				_mali_osk_list_empty(&job_queue_gp.normal_pri) ?
+				"empty" : "not empty");
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tHigh priority queue is %s\n",
+				_mali_osk_list_empty(&job_queue_gp.high_pri) ?
+				"empty" : "not empty");
+
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"PP queues\n");
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tQueue depth: %u\n", job_queue_pp.depth);
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tNormal priority queue is %s\n",
+				_mali_osk_list_empty(&job_queue_pp.normal_pri)
+				? "empty" : "not empty");
+	n += _mali_osk_snprintf(buf + n, size - n,
+				"\tHigh priority queue is %s\n",
+				_mali_osk_list_empty(&job_queue_pp.high_pri)
+				? "empty" : "not empty");
+
+	n += _mali_osk_snprintf(buf + n, size - n, "\n");
+
+	return n;
+}
+#endif
+
+/*
+ * ---------- Implementation of static functions ----------
+ */
+
+static mali_timeline_point mali_scheduler_submit_gp_job(
+	struct mali_session_data *session, struct mali_gp_job *job)
+{
+	mali_timeline_point point;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	/* Add job to Timeline system. */
+	point = mali_timeline_system_add_tracker(session->timeline_system,
+			mali_gp_job_get_tracker(job), MALI_TIMELINE_GP);
+
+	return point;
+}
+
+static _mali_osk_errcode_t mali_scheduler_submit_pp_job(
+	struct mali_session_data *session, struct mali_pp_job *job, mali_timeline_point *point)
+
+{
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_OK;
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	struct ww_acquire_ctx ww_actx;
+	u32 i;
+	u32 num_memory_cookies = 0;
+	struct reservation_object **reservation_object_list = NULL;
+	unsigned int num_reservation_object = 0;
+#endif
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	mali_scheduler_lock();
+	/*
+	 * Adding job to the lookup list used to quickly discard
+	 * writeback units of queued jobs.
+	 */
+	mali_pp_job_fb_lookup_add(job);
+	mali_scheduler_unlock();
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+
+	/* Allocate the reservation_object_list to list the dma reservation object of dependent dma buffer */
+	num_memory_cookies = mali_pp_job_num_memory_cookies(job);
+	if (0 < num_memory_cookies) {
+		reservation_object_list = kzalloc(sizeof(struct reservation_object *) * num_memory_cookies, GFP_KERNEL);
+		if (NULL == reservation_object_list) {
+			MALI_PRINT_ERROR(("Failed to alloc the reservation object list.\n"));
+			ret = _MALI_OSK_ERR_NOMEM;
+			goto failed_to_alloc_reservation_object_list;
+		}
+	}
+
+	/* Add the dma reservation object into reservation_object_list*/
+	for (i = 0; i < num_memory_cookies; i++) {
+		mali_mem_backend *mem_backend = NULL;
+		struct reservation_object *tmp_reservation_object = NULL;
+		u32 mali_addr  = mali_pp_job_get_memory_cookie(job, i);
+
+		mem_backend = mali_mem_backend_struct_search(session, mali_addr);
+
+		MALI_DEBUG_ASSERT_POINTER(mem_backend);
+
+		if (NULL == mem_backend) {
+			MALI_PRINT_ERROR(("Failed to find the memory backend for memory cookie[%d].\n", i));
+			goto failed_to_find_mem_backend;
+		}
+
+		if (MALI_MEM_DMA_BUF != mem_backend->type)
+			continue;
+
+		tmp_reservation_object = mem_backend->dma_buf.attachment->buf->resv;
+
+		if (NULL != tmp_reservation_object) {
+			mali_dma_fence_add_reservation_object_list(tmp_reservation_object,
+					reservation_object_list, &num_reservation_object);
+		}
+	}
+
+	/*
+	 * Add the mali dma fence callback to wait for all dependent dma buf,
+	 * and extend the timeline system to support dma fence,
+	 * then create the new internal dma fence to replace all last dma fence for dependent dma buf.
+	 */
+	if (0 < num_reservation_object) {
+		int error;
+		int num_dma_fence_waiter = 0;
+		/* Create one new dma fence.*/
+		job->rendered_dma_fence = mali_dma_fence_new(job->session->fence_context,
+					  _mali_osk_atomic_inc_return(&job->session->fence_seqno));
+
+		if (NULL == job->rendered_dma_fence) {
+			MALI_PRINT_ERROR(("Failed to creat one new dma fence.\n"));
+			ret = _MALI_OSK_ERR_FAULT;
+			goto failed_to_create_dma_fence;
+		}
+
+		/* In order to avoid deadlock, wait/wound mutex lock to lock all dma buffers*/
+
+		error = mali_dma_fence_lock_reservation_object_list(reservation_object_list,
+				num_reservation_object, &ww_actx);
+
+		if (0 != error) {
+			MALI_PRINT_ERROR(("Failed to lock all reservation objects.\n"));
+			ret = _MALI_OSK_ERR_FAULT;
+			goto failed_to_lock_reservation_object_list;
+		}
+
+		mali_dma_fence_context_init(&job->dma_fence_context,
+					    mali_timeline_dma_fence_callback, (void *)job);
+
+		/* Add dma fence waiters and dma fence callback. */
+		for (i = 0; i < num_reservation_object; i++) {
+			ret = mali_dma_fence_context_add_waiters(&job->dma_fence_context, reservation_object_list[i]);
+			if (_MALI_OSK_ERR_OK != ret) {
+				MALI_PRINT_ERROR(("Failed to add waiter into mali dma fence context.\n"));
+				goto failed_to_add_dma_fence_waiter;
+			}
+		}
+
+		for (i = 0; i < num_reservation_object; i++) {
+			reservation_object_add_excl_fence(reservation_object_list[i], job->rendered_dma_fence);
+		}
+
+		num_dma_fence_waiter = job->dma_fence_context.num_dma_fence_waiter;
+
+		/* Add job to Timeline system. */
+		(*point) = mali_timeline_system_add_tracker(session->timeline_system,
+				mali_pp_job_get_tracker(job), MALI_TIMELINE_PP);
+
+		if (0 != num_dma_fence_waiter) {
+			mali_dma_fence_context_dec_count(&job->dma_fence_context);
+		}
+
+		/* Unlock all wait/wound mutex lock. */
+		mali_dma_fence_unlock_reservation_object_list(reservation_object_list,
+				num_reservation_object, &ww_actx);
+	} else {
+		/* Add job to Timeline system. */
+		(*point) = mali_timeline_system_add_tracker(session->timeline_system,
+				mali_pp_job_get_tracker(job), MALI_TIMELINE_PP);
+	}
+
+	kfree(reservation_object_list);
+	return ret;
+#else
+	/* Add job to Timeline system. */
+	(*point) = mali_timeline_system_add_tracker(session->timeline_system,
+			mali_pp_job_get_tracker(job), MALI_TIMELINE_PP);
+#endif
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+failed_to_add_dma_fence_waiter:
+	mali_dma_fence_context_term(&job->dma_fence_context);
+	mali_dma_fence_unlock_reservation_object_list(reservation_object_list,
+			num_reservation_object, &ww_actx);
+failed_to_lock_reservation_object_list:
+	mali_dma_fence_signal_and_put(&job->rendered_dma_fence);
+failed_to_create_dma_fence:
+failed_to_find_mem_backend:
+	if (NULL != reservation_object_list)
+		kfree(reservation_object_list);
+failed_to_alloc_reservation_object_list:
+	mali_pp_job_fb_lookup_remove(job);
+#endif
+	return ret;
+}
+
+static mali_bool mali_scheduler_queue_gp_job(struct mali_gp_job *job)
+{
+	struct mali_session_data *session;
+	_mali_osk_list_t *queue;
+
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	session = mali_gp_job_get_session(job);
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (unlikely(session->is_aborting)) {
+		MALI_DEBUG_PRINT(4, ("Mali GP scheduler: Job %u (0x%08X) queued while session is aborting.\n",
+				     mali_gp_job_get_id(job), job));
+		return MALI_FALSE; /* job not queued */
+	}
+
+	mali_gp_job_set_cache_order(job, mali_scheduler_get_new_cache_order());
+
+	/* Determine which queue the job should be added to. */
+	if (session->use_high_priority_job_queue) {
+		queue = &job_queue_gp.high_pri;
+	} else {
+		queue = &job_queue_gp.normal_pri;
+	}
+
+	job_queue_gp.depth += 1;
+	job_queue_gp.big_job_num += (job->big_job) ? 1 : 0;
+
+	/* Add job to queue (mali_gp_job_queue_add find correct place). */
+	mali_gp_job_list_add(job, queue);
+
+	/*
+	 * We hold a PM reference for every job we hold queued (and running)
+	 * It is important that we take this reference after job has been
+	 * added the the queue so that any runtime resume could schedule this
+	 * job right there and then.
+	 */
+	_mali_osk_pm_dev_ref_get_async();
+
+	if (mali_utilization_enabled()) {
+		/*
+		 * We cheat a little bit by counting the GP as busy from the
+		 * time a GP job is queued. This will be fine because we only
+		 * loose the tiny idle gap between jobs, but we will instead
+		 * get less utilization work to do (less locks taken)
+		 */
+		mali_utilization_gp_start();
+	}
+
+	mali_pm_record_gpu_active(MALI_TRUE);
+
+	/* Add profiling events for job enqueued */
+	_mali_osk_profiling_add_event(
+		MALI_PROFILING_EVENT_TYPE_SINGLE |
+		MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+		MALI_PROFILING_EVENT_REASON_SINGLE_SW_GP_ENQUEUE,
+		mali_gp_job_get_pid(job),
+		mali_gp_job_get_tid(job),
+		mali_gp_job_get_frame_builder_id(job),
+		mali_gp_job_get_flush_id(job),
+		0);
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+	trace_gpu_job_enqueue(mali_gp_job_get_tid(job),
+			      mali_gp_job_get_id(job), "GP");
+#endif
+
+	MALI_DEBUG_PRINT(3, ("Mali GP scheduler: Job %u (0x%08X) queued\n",
+			     mali_gp_job_get_id(job), job));
+
+	return MALI_TRUE; /* job queued */
+}
+
+static mali_bool mali_scheduler_queue_pp_job(struct mali_pp_job *job)
+{
+	struct mali_session_data *session;
+	_mali_osk_list_t *queue = NULL;
+
+	MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD();
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	session = mali_pp_job_get_session(job);
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (unlikely(session->is_aborting)) {
+		MALI_DEBUG_PRINT(2, ("Mali PP scheduler: Job %u (0x%08X) queued while session is aborting.\n",
+				     mali_pp_job_get_id(job), job));
+		return MALI_FALSE; /* job not queued */
+	} else if (unlikely(MALI_SWAP_IN_FAIL == job->swap_status)) {
+		MALI_DEBUG_PRINT(2, ("Mali PP scheduler: Job %u (0x%08X) queued while swap in failed.\n",
+				     mali_pp_job_get_id(job), job));
+		return MALI_FALSE;
+	}
+
+	mali_pp_job_set_cache_order(job, mali_scheduler_get_new_cache_order());
+
+	if (session->use_high_priority_job_queue) {
+		queue = &job_queue_pp.high_pri;
+	} else {
+		queue = &job_queue_pp.normal_pri;
+	}
+
+	job_queue_pp.depth +=
+		mali_pp_job_get_sub_job_count(job);
+
+	/* Add job to queue (mali_gp_job_queue_add find correct place). */
+	mali_pp_job_list_add(job, queue);
+
+	/*
+	 * We hold a PM reference for every job we hold queued (and running)
+	 * It is important that we take this reference after job has been
+	 * added the the queue so that any runtime resume could schedule this
+	 * job right there and then.
+	 */
+	_mali_osk_pm_dev_ref_get_async();
+
+	if (mali_utilization_enabled()) {
+		/*
+		 * We cheat a little bit by counting the PP as busy from the
+		 * time a PP job is queued. This will be fine because we only
+		 * loose the tiny idle gap between jobs, but we will instead
+		 * get less utilization work to do (less locks taken)
+		 */
+		mali_utilization_pp_start();
+	}
+
+	mali_pm_record_gpu_active(MALI_FALSE);
+
+	/* Add profiling events for job enqueued */
+	_mali_osk_profiling_add_event(
+		MALI_PROFILING_EVENT_TYPE_SINGLE |
+		MALI_PROFILING_EVENT_CHANNEL_SOFTWARE |
+		MALI_PROFILING_EVENT_REASON_SINGLE_SW_PP_ENQUEUE,
+		mali_pp_job_get_pid(job),
+		mali_pp_job_get_tid(job),
+		mali_pp_job_get_frame_builder_id(job),
+		mali_pp_job_get_flush_id(job),
+		0);
+
+#if defined(CONFIG_GPU_TRACEPOINTS) && defined(CONFIG_TRACEPOINTS)
+	trace_gpu_job_enqueue(mali_pp_job_get_tid(job),
+			      mali_pp_job_get_id(job), "PP");
+#endif
+
+	MALI_DEBUG_PRINT(3, ("Mali PP scheduler: %s job %u (0x%08X) with %u parts queued.\n",
+			     mali_pp_job_is_virtual(job)
+			     ? "Virtual" : "Physical",
+			     mali_pp_job_get_id(job), job,
+			     mali_pp_job_get_sub_job_count(job)));
+
+	return MALI_TRUE; /* job queued */
+}
+
+static void mali_scheduler_return_gp_job_to_user(struct mali_gp_job *job,
+		mali_bool success)
+{
+	_mali_uk_gp_job_finished_s *jobres;
+	struct mali_session_data *session;
+	_mali_osk_notification_t *notification;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	session = mali_gp_job_get_session(job);
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	notification = mali_gp_job_get_finished_notification(job);
+	MALI_DEBUG_ASSERT_POINTER(notification);
+
+	jobres = notification->result_buffer;
+	MALI_DEBUG_ASSERT_POINTER(jobres);
+
+	jobres->pending_big_job_num = mali_scheduler_job_gp_big_job_count();
+
+	jobres->user_job_ptr = mali_gp_job_get_user_id(job);
+	if (MALI_TRUE == success) {
+		jobres->status = _MALI_UK_JOB_STATUS_END_SUCCESS;
+	} else {
+		jobres->status = _MALI_UK_JOB_STATUS_END_UNKNOWN_ERR;
+	}
+	jobres->heap_current_addr = mali_gp_job_get_current_heap_addr(job);
+	jobres->perf_counter0 = mali_gp_job_get_perf_counter_value0(job);
+	jobres->perf_counter1 = mali_gp_job_get_perf_counter_value1(job);
+
+	mali_session_send_notification(session, notification);
+}
+
+void mali_scheduler_return_pp_job_to_user(struct mali_pp_job *job,
+		u32 num_cores_in_virtual)
+{
+	u32 i;
+	u32 num_counters_to_copy;
+	_mali_uk_pp_job_finished_s *jobres;
+	struct mali_session_data *session;
+	_mali_osk_notification_t *notification;
+
+	if (MALI_TRUE == mali_pp_job_use_no_notification(job)) {
+		return;
+	}
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	session = mali_pp_job_get_session(job);
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	notification = mali_pp_job_get_finished_notification(job);
+	MALI_DEBUG_ASSERT_POINTER(notification);
+
+	jobres = notification->result_buffer;
+	MALI_DEBUG_ASSERT_POINTER(jobres);
+
+	jobres->user_job_ptr = mali_pp_job_get_user_id(job);
+	if (MALI_TRUE == mali_pp_job_was_success(job)) {
+		jobres->status = _MALI_UK_JOB_STATUS_END_SUCCESS;
+	} else {
+		jobres->status = _MALI_UK_JOB_STATUS_END_UNKNOWN_ERR;
+	}
+
+	if (mali_pp_job_is_virtual(job)) {
+		num_counters_to_copy = num_cores_in_virtual;
+	} else {
+		num_counters_to_copy = mali_pp_job_get_sub_job_count(job);
+	}
+
+	for (i = 0; i < num_counters_to_copy; i++) {
+		jobres->perf_counter0[i] =
+			mali_pp_job_get_perf_counter_value0(job, i);
+		jobres->perf_counter1[i] =
+			mali_pp_job_get_perf_counter_value1(job, i);
+		jobres->perf_counter_src0 =
+			mali_pp_job_get_pp_counter_global_src0();
+		jobres->perf_counter_src1 =
+			mali_pp_job_get_pp_counter_global_src1();
+	}
+
+	mali_session_send_notification(session, notification);
+}
+
+static void mali_scheduler_deferred_pp_job_delete(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	_mali_osk_spinlock_irq_lock(scheduler_pp_job_delete_lock);
+	mali_pp_job_list_addtail(job, &scheduler_pp_job_deletion_queue);
+	_mali_osk_spinlock_irq_unlock(scheduler_pp_job_delete_lock);
+
+	_mali_osk_wq_schedule_work(scheduler_wq_pp_job_delete);
+}
+
+void mali_scheduler_do_pp_job_delete(void *arg)
+{
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(list);
+	struct mali_pp_job *job;
+	struct mali_pp_job *tmp;
+
+	MALI_IGNORE(arg);
+
+	/*
+	 * Quickly "unhook" the jobs pending to be deleted, so we can release
+	 * the lock before we start deleting the job objects
+	 * (without any locks held)
+	 */
+	_mali_osk_spinlock_irq_lock(scheduler_pp_job_delete_lock);
+	_mali_osk_list_move_list(&scheduler_pp_job_deletion_queue, &list);
+	_mali_osk_spinlock_irq_unlock(scheduler_pp_job_delete_lock);
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp, &list,
+				    struct mali_pp_job, list) {
+		_mali_osk_list_delinit(&job->list);
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+		mali_dma_fence_context_term(&job->dma_fence_context);
+#endif
+
+		mali_pp_job_delete(job); /* delete the job object itself */
+	}
+}
+
+#if defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE)
+
+static void mali_scheduler_deferred_pp_job_queue(struct mali_pp_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	_mali_osk_spinlock_irq_lock(scheduler_pp_job_queue_lock);
+	mali_pp_job_list_addtail(job, &scheduler_pp_job_queue_list);
+	_mali_osk_spinlock_irq_unlock(scheduler_pp_job_queue_lock);
+
+	_mali_osk_wq_schedule_work(scheduler_wq_pp_job_queue);
+}
+
+static void mali_scheduler_do_pp_job_queue(void *arg)
+{
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(list);
+	struct mali_pp_job *job;
+	struct mali_pp_job *tmp;
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_IGNORE(arg);
+
+	/*
+	 * Quickly "unhook" the jobs pending to be queued, so we can release
+	 * the lock before we start queueing the job objects
+	 * (without any locks held)
+	 */
+	_mali_osk_spinlock_irq_lock(scheduler_pp_job_queue_lock);
+	_mali_osk_list_move_list(&scheduler_pp_job_queue_list, &list);
+	_mali_osk_spinlock_irq_unlock(scheduler_pp_job_queue_lock);
+
+	/* First loop through all jobs and do the pre-work (no locks needed) */
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp, &list,
+				    struct mali_pp_job, list) {
+		if (mali_pp_job_needs_dma_buf_mapping(job)) {
+			/*
+			 * This operation could fail, but we continue anyway,
+			 * because the worst that could happen is that this
+			 * job will fail due to a Mali page fault.
+			 */
+			mali_dma_buf_map_job(job);
+		}
+	}
+
+	mali_scheduler_lock();
+
+	/* Then loop through all jobs again to queue them (lock needed) */
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp, &list,
+				    struct mali_pp_job, list) {
+
+		/* Remove from scheduler_pp_job_queue_list before queueing */
+		mali_pp_job_list_remove(job);
+
+		if (mali_scheduler_queue_pp_job(job)) {
+			/* Job queued successfully */
+			schedule_mask |= MALI_SCHEDULER_MASK_PP;
+		} else {
+			/* Failed to enqueue job, release job (with error) */
+			mali_pp_job_fb_lookup_remove(job);
+			mali_pp_job_mark_unstarted_failed(job);
+
+			/* unlock scheduler in this uncommon case */
+			mali_scheduler_unlock();
+
+			schedule_mask |= mali_timeline_tracker_release(
+						 mali_pp_job_get_tracker(job));
+
+			/* Notify user space and close the job object */
+			mali_scheduler_complete_pp_job(job, 0, MALI_TRUE,
+						       MALI_FALSE);
+
+			mali_scheduler_lock();
+		}
+	}
+
+	mali_scheduler_unlock();
+
+	/* Trigger scheduling of jobs */
+	mali_executor_schedule_from_mask(schedule_mask, MALI_FALSE);
+}
+
+#endif /* defined(MALI_SCHEDULER_USE_DEFERRED_PP_JOB_QUEUE) */
+
+void mali_scheduler_gp_pp_job_queue_print(void)
+{
+	struct mali_gp_job *gp_job = NULL;
+	struct mali_gp_job *tmp_gp_job = NULL;
+	struct mali_pp_job *pp_job = NULL;
+	struct mali_pp_job *tmp_pp_job = NULL;
+
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+	MALI_DEBUG_ASSERT_LOCK_HELD(mali_executor_lock_obj);
+
+	/* dump job queup status */
+	if ((0 == job_queue_gp.depth) && (0 == job_queue_pp.depth)) {
+		MALI_PRINT(("No GP&PP job in the job queue.\n"));
+		return;
+	}
+
+	MALI_PRINT(("Total (%d) GP job in the job queue.\n", job_queue_gp.depth));
+	if (job_queue_gp.depth > 0) {
+		if (!_mali_osk_list_empty(&job_queue_gp.high_pri)) {
+			_MALI_OSK_LIST_FOREACHENTRY(gp_job, tmp_gp_job, &job_queue_gp.high_pri,
+						    struct mali_gp_job, list) {
+				MALI_PRINT(("GP job(%p) id = %d tid = %d pid = %d in the gp job high_pri queue\n", gp_job, gp_job->id, gp_job->tid, gp_job->pid));
+			}
+		}
+
+		if (!_mali_osk_list_empty(&job_queue_gp.normal_pri)) {
+			_MALI_OSK_LIST_FOREACHENTRY(gp_job, tmp_gp_job, &job_queue_gp.normal_pri,
+						    struct mali_gp_job, list) {
+				MALI_PRINT(("GP job(%p) id = %d tid = %d pid = %d in the gp job normal_pri queue\n", gp_job, gp_job->id, gp_job->tid, gp_job->pid));
+			}
+		}
+	}
+
+	MALI_PRINT(("Total (%d) PP job in the job queue.\n", job_queue_pp.depth));
+	if (job_queue_pp.depth > 0) {
+		if (!_mali_osk_list_empty(&job_queue_pp.high_pri)) {
+			_MALI_OSK_LIST_FOREACHENTRY(pp_job, tmp_pp_job, &job_queue_pp.high_pri,
+						    struct mali_pp_job, list) {
+				if (mali_pp_job_is_virtual(pp_job)) {
+					MALI_PRINT(("PP Virtual job(%p) id = %d tid = %d pid = %d in the pp job high_pri queue\n", pp_job, pp_job->id, pp_job->tid, pp_job->pid));
+				} else {
+					MALI_PRINT(("PP Physical job(%p) id = %d tid = %d pid = %d in the pp job high_pri queue\n", pp_job, pp_job->id, pp_job->tid, pp_job->pid));
+				}
+			}
+		}
+
+		if (!_mali_osk_list_empty(&job_queue_pp.normal_pri)) {
+			_MALI_OSK_LIST_FOREACHENTRY(pp_job, tmp_pp_job, &job_queue_pp.normal_pri,
+						    struct mali_pp_job, list) {
+				if (mali_pp_job_is_virtual(pp_job)) {
+					MALI_PRINT(("PP Virtual job(%p) id = %d tid = %d pid = %d in the pp job normal_pri queue\n", pp_job, pp_job->id, pp_job->tid, pp_job->pid));
+				} else {
+					MALI_PRINT(("PP Physical job(%p) id = %d tid = %d pid = %d in the pp job normal_pri queue\n", pp_job, pp_job->id, pp_job->tid, pp_job->pid));
+				}
+			}
+		}
+	}
+
+	/* dump group running job status */
+	mali_executor_running_status_print();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_scheduler.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_scheduler.h
@@ -0,0 +1,131 @@
+/*
+ * Copyright (C) 2012-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_SCHEDULER_H__
+#define __MALI_SCHEDULER_H__
+
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_scheduler_types.h"
+#include "mali_session.h"
+
+struct mali_scheduler_job_queue {
+	_MALI_OSK_LIST_HEAD(normal_pri); /* Queued jobs with normal priority */
+	_MALI_OSK_LIST_HEAD(high_pri);   /* Queued jobs with high priority */
+	u32 depth;                       /* Depth of combined queues. */
+	u32 big_job_num;
+};
+
+extern _mali_osk_spinlock_irq_t *mali_scheduler_lock_obj;
+
+/* Queue of jobs to be executed on the GP group */
+extern struct mali_scheduler_job_queue job_queue_gp;
+
+/* Queue of PP jobs */
+extern struct mali_scheduler_job_queue job_queue_pp;
+
+extern _mali_osk_atomic_t mali_job_id_autonumber;
+extern _mali_osk_atomic_t mali_job_cache_order_autonumber;
+
+#define MALI_DEBUG_ASSERT_SCHEDULER_LOCK_HELD() MALI_DEBUG_ASSERT_LOCK_HELD(mali_scheduler_lock_obj);
+
+_mali_osk_errcode_t mali_scheduler_initialize(void);
+void mali_scheduler_terminate(void);
+
+MALI_STATIC_INLINE void mali_scheduler_lock(void)
+{
+	_mali_osk_spinlock_irq_lock(mali_scheduler_lock_obj);
+	MALI_DEBUG_PRINT(5, ("Mali scheduler: scheduler lock taken.\n"));
+}
+
+MALI_STATIC_INLINE void mali_scheduler_unlock(void)
+{
+	MALI_DEBUG_PRINT(5, ("Mali scheduler: Releasing scheduler lock.\n"));
+	_mali_osk_spinlock_irq_unlock(mali_scheduler_lock_obj);
+}
+
+MALI_STATIC_INLINE u32 mali_scheduler_job_gp_count(void)
+{
+	return job_queue_gp.depth;
+}
+MALI_STATIC_INLINE u32 mali_scheduler_job_gp_big_job_count(void)
+{
+	return job_queue_gp.big_job_num;
+}
+
+u32 mali_scheduler_job_physical_head_count(mali_bool gpu_mode_is_secure);
+
+mali_bool mali_scheduler_job_next_is_virtual(void);
+struct mali_pp_job *mali_scheduler_job_pp_next(void);
+
+struct mali_gp_job *mali_scheduler_job_gp_get(void);
+struct mali_pp_job *mali_scheduler_job_pp_physical_peek(void);
+struct mali_pp_job *mali_scheduler_job_pp_virtual_peek(void);
+struct mali_pp_job *mali_scheduler_job_pp_physical_get(u32 *sub_job);
+struct mali_pp_job *mali_scheduler_job_pp_virtual_get(void);
+
+MALI_STATIC_INLINE u32 mali_scheduler_get_new_id(void)
+{
+	return _mali_osk_atomic_inc_return(&mali_job_id_autonumber);
+}
+
+MALI_STATIC_INLINE u32 mali_scheduler_get_new_cache_order(void)
+{
+	return _mali_osk_atomic_inc_return(&mali_job_cache_order_autonumber);
+}
+
+/**
+ * @brief Used by the Timeline system to queue a GP job.
+ *
+ * @note @ref mali_executor_schedule_from_mask() should be called if this
+ * function returns non-zero.
+ *
+ * @param job The GP job that is being activated.
+ *
+ * @return A scheduling bitmask that can be used to decide if scheduling is
+ * necessary after this call.
+ */
+mali_scheduler_mask mali_scheduler_activate_gp_job(struct mali_gp_job *job);
+
+/**
+ * @brief Used by the Timeline system to queue a PP job.
+ *
+ * @note @ref mali_executor_schedule_from_mask() should be called if this
+ * function returns non-zero.
+ *
+ * @param job The PP job that is being activated.
+ *
+ * @return A scheduling bitmask that can be used to decide if scheduling is
+ * necessary after this call.
+ */
+mali_scheduler_mask mali_scheduler_activate_pp_job(struct mali_pp_job *job);
+
+void mali_scheduler_complete_gp_job(struct mali_gp_job *job,
+				    mali_bool success,
+				    mali_bool user_notification,
+				    mali_bool dequeued);
+
+void mali_scheduler_complete_pp_job(struct mali_pp_job *job,
+				    u32 num_cores_in_virtual,
+				    mali_bool user_notification,
+				    mali_bool dequeued);
+
+void mali_scheduler_abort_session(struct mali_session_data *session);
+
+void mali_scheduler_return_pp_job_to_user(struct mali_pp_job *job,
+		u32 num_cores_in_virtual);
+
+#if MALI_STATE_TRACKING
+u32 mali_scheduler_dump_state(char *buf, u32 size);
+#endif
+
+void mali_scheduler_gp_pp_job_queue_print(void);
+
+#endif /* __MALI_SCHEDULER_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_scheduler_types.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_scheduler_types.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_SCHEDULER_TYPES_H__
+#define __MALI_SCHEDULER_TYPES_H__
+
+#include "mali_osk.h"
+
+#define MALI_SCHEDULER_JOB_ID_SPAN 65535
+
+/**
+ * Bitmask used for defered scheduling of subsystems.
+ */
+typedef u32 mali_scheduler_mask;
+
+#define MALI_SCHEDULER_MASK_GP (1<<0)
+#define MALI_SCHEDULER_MASK_PP (1<<1)
+
+#define MALI_SCHEDULER_MASK_EMPTY 0
+#define MALI_SCHEDULER_MASK_ALL (MALI_SCHEDULER_MASK_GP | MALI_SCHEDULER_MASK_PP)
+
+#endif /* __MALI_SCHEDULER_TYPES_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_session.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_session.c
@@ -0,0 +1,155 @@
+/*
+ * Copyright (C) 2012-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_session.h"
+#include "mali_ukk.h"
+#ifdef MALI_MEM_SWAP_TRACKING
+#include "mali_memory_swap_alloc.h"
+#endif
+
+_MALI_OSK_LIST_HEAD(mali_sessions);
+static u32 mali_session_count = 0;
+
+_mali_osk_spinlock_irq_t *mali_sessions_lock = NULL;
+wait_queue_head_t pending_queue;
+
+_mali_osk_errcode_t mali_session_initialize(void)
+{
+	_MALI_OSK_INIT_LIST_HEAD(&mali_sessions);
+	/* init wait queue for big varying job */
+	init_waitqueue_head(&pending_queue);
+
+	mali_sessions_lock = _mali_osk_spinlock_irq_init(
+				     _MALI_OSK_LOCKFLAG_ORDERED,
+				     _MALI_OSK_LOCK_ORDER_SESSIONS);
+	if (NULL == mali_sessions_lock) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_session_terminate(void)
+{
+	if (NULL != mali_sessions_lock) {
+		_mali_osk_spinlock_irq_term(mali_sessions_lock);
+		mali_sessions_lock = NULL;
+	}
+}
+
+void mali_session_add(struct mali_session_data *session)
+{
+	mali_session_lock();
+	_mali_osk_list_add(&session->link, &mali_sessions);
+	mali_session_count++;
+	mali_session_unlock();
+}
+
+void mali_session_remove(struct mali_session_data *session)
+{
+	mali_session_lock();
+	_mali_osk_list_delinit(&session->link);
+	mali_session_count--;
+	mali_session_unlock();
+}
+
+u32 mali_session_get_count(void)
+{
+	return mali_session_count;
+}
+
+mali_bool mali_session_pp_job_is_empty(void *data)
+{
+	struct mali_session_data *session = (struct mali_session_data *)data;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (0 == _mali_osk_atomic_read(&session->number_of_pp_jobs)) {
+		return MALI_TRUE;
+	}
+	return MALI_FALSE;
+}
+
+wait_queue_head_t *mali_session_get_wait_queue(void)
+{
+	return &pending_queue;
+}
+
+/*
+ * Get the max completed window jobs from all active session,
+ * which will be used in window render frame per sec calculate
+ */
+#if defined(CONFIG_MALI_DVFS)
+u32 mali_session_max_window_num(void)
+{
+	struct mali_session_data *session, *tmp;
+	u32 max_window_num = 0;
+	u32 tmp_number = 0;
+
+	mali_session_lock();
+
+	MALI_SESSION_FOREACH(session, tmp, link) {
+		tmp_number = _mali_osk_atomic_xchg(
+				     &session->number_of_window_jobs, 0);
+		if (max_window_num < tmp_number) {
+			max_window_num = tmp_number;
+		}
+	}
+
+	mali_session_unlock();
+
+	return max_window_num;
+}
+#endif
+
+void mali_session_memory_tracking(_mali_osk_print_ctx *print_ctx)
+{
+	struct mali_session_data *session, *tmp;
+	u32 mali_mem_usage;
+	u32 total_mali_mem_size;
+#ifdef MALI_MEM_SWAP_TRACKING
+	u32 swap_pool_size;
+	u32 swap_unlock_size;
+#endif
+
+	MALI_DEBUG_ASSERT_POINTER(print_ctx);
+	mali_session_lock();
+	MALI_SESSION_FOREACH(session, tmp, link) {
+#ifdef MALI_MEM_SWAP_TRACKING
+		_mali_osk_ctxprintf(print_ctx, "  %-25s  %-10u  %-10u  %-15u  %-15u  %-10u  %-10u  %-10u\n",
+				    session->comm, session->pid,
+				    (atomic_read(&session->mali_mem_allocated_pages)) * _MALI_OSK_MALI_PAGE_SIZE,
+				    (unsigned int)session->max_mali_mem_allocated_size,
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_EXTERNAL])) * _MALI_OSK_MALI_PAGE_SIZE),
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_UMP])) * _MALI_OSK_MALI_PAGE_SIZE),
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_DMA_BUF])) * _MALI_OSK_MALI_PAGE_SIZE),
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_SWAP])) * _MALI_OSK_MALI_PAGE_SIZE)
+				   );
+#else
+		_mali_osk_ctxprintf(print_ctx, "  %-25s  %-10u  %-10u  %-15u  %-15u  %-10u  %-10u  \n",
+				    session->comm, session->pid,
+				    (unsigned int)((atomic_read(&session->mali_mem_allocated_pages)) * _MALI_OSK_MALI_PAGE_SIZE),
+				    (unsigned int)session->max_mali_mem_allocated_size,
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_EXTERNAL])) * _MALI_OSK_MALI_PAGE_SIZE),
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_UMP])) * _MALI_OSK_MALI_PAGE_SIZE),
+				    (unsigned int)((atomic_read(&session->mali_mem_array[MALI_MEM_DMA_BUF])) * _MALI_OSK_MALI_PAGE_SIZE)
+				   );
+#endif
+	}
+	mali_session_unlock();
+	mali_mem_usage  = _mali_ukk_report_memory_usage();
+	total_mali_mem_size = _mali_ukk_report_total_memory_size();
+	_mali_osk_ctxprintf(print_ctx, "Mali mem usage: %u\nMali mem limit: %u\n", mali_mem_usage, total_mali_mem_size);
+#ifdef MALI_MEM_SWAP_TRACKING
+	mali_mem_swap_tracking(&swap_pool_size, &swap_unlock_size);
+	_mali_osk_ctxprintf(print_ctx, "Mali swap mem pool : %u\nMali swap mem unlock: %u\n", swap_pool_size, swap_unlock_size);
+#endif
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_session.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_session.h
@@ -0,0 +1,136 @@
+/*
+ * Copyright (C) 2010-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_SESSION_H__
+#define __MALI_SESSION_H__
+
+#include "mali_mmu_page_directory.h"
+#include "mali_osk.h"
+#include "mali_osk_list.h"
+#include "mali_memory_types.h"
+#include "mali_memory_manager.h"
+
+struct mali_timeline_system;
+struct mali_soft_system;
+
+/* Number of frame builder job lists per session. */
+#define MALI_PP_JOB_FB_LOOKUP_LIST_SIZE 16
+#define MALI_PP_JOB_FB_LOOKUP_LIST_MASK (MALI_PP_JOB_FB_LOOKUP_LIST_SIZE - 1)
+/*Max pending big job allowed in kernel*/
+#define MALI_MAX_PENDING_BIG_JOB (2)
+
+struct mali_session_data {
+	_mali_osk_notification_queue_t *ioctl_queue;
+
+	_mali_osk_wait_queue_t *wait_queue; /**The wait queue to wait for the number of pp job become 0.*/
+
+	_mali_osk_mutex_t *memory_lock; /**< Lock protecting the vm manipulation */
+	_mali_osk_mutex_t *cow_lock; /** < Lock protecting the cow memory free manipulation */
+#if 0
+	_mali_osk_list_t memory_head; /**< Track all the memory allocated in this session, for freeing on abnormal termination */
+#endif
+	struct mali_page_directory *page_directory; /**< MMU page directory for this session */
+
+	_MALI_OSK_LIST_HEAD(link); /**< Link for list of all sessions */
+	_MALI_OSK_LIST_HEAD(pp_job_list); /**< List of all PP jobs on this session */
+
+#if defined(CONFIG_MALI_DVFS)
+	_mali_osk_atomic_t number_of_window_jobs; /**< Record the window jobs completed on this session in a period */
+#endif
+	_mali_osk_atomic_t number_of_pp_jobs; /** < Record the pp jobs on this session */
+
+	_mali_osk_list_t pp_job_fb_lookup_list[MALI_PP_JOB_FB_LOOKUP_LIST_SIZE]; /**< List of PP job lists per frame builder id.  Used to link jobs from same frame builder. */
+	struct mali_soft_job_system *soft_job_system; /**< Soft job system for this session. */
+	struct mali_timeline_system *timeline_system; /**< Timeline system for this session. */
+
+	mali_bool is_aborting; /**< MALI_TRUE if the session is aborting, MALI_FALSE if not. */
+	mali_bool use_high_priority_job_queue; /**< If MALI_TRUE, jobs added from this session will use the high priority job queues. */
+	u32 pid;
+	char *comm;
+	atomic_t mali_mem_array[MALI_MEM_TYPE_MAX]; /**< The array to record mem types' usage for this session. */
+	atomic_t mali_mem_allocated_pages; /** The current allocated mali memory pages, which include mali os memory and mali dedicated memory.*/
+	size_t max_mali_mem_allocated_size; /**< The past max mali memory allocated size, which include mali os memory and mali dedicated memory. */
+	/* Added for new memroy system */
+	struct mali_allocation_manager allocation_mgr;
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	u32 fence_context;      /** <  The execution dma fence context this fence is run on. */
+	_mali_osk_atomic_t fence_seqno; /** < Alinear increasing sequence number for this dma fence context. */
+#endif
+};
+
+_mali_osk_errcode_t mali_session_initialize(void);
+void mali_session_terminate(void);
+
+/* List of all sessions. Actual list head in mali_kernel_core.c */
+extern _mali_osk_list_t mali_sessions;
+/* Lock to protect modification and access to the mali_sessions list */
+extern _mali_osk_spinlock_irq_t *mali_sessions_lock;
+
+MALI_STATIC_INLINE void mali_session_lock(void)
+{
+	_mali_osk_spinlock_irq_lock(mali_sessions_lock);
+}
+
+MALI_STATIC_INLINE void mali_session_unlock(void)
+{
+	_mali_osk_spinlock_irq_unlock(mali_sessions_lock);
+}
+
+void mali_session_add(struct mali_session_data *session);
+void mali_session_remove(struct mali_session_data *session);
+u32 mali_session_get_count(void);
+mali_bool mali_session_pp_job_is_empty(void *data);
+wait_queue_head_t *mali_session_get_wait_queue(void);
+
+#define MALI_SESSION_FOREACH(session, tmp, link) \
+	_MALI_OSK_LIST_FOREACHENTRY(session, tmp, &mali_sessions, struct mali_session_data, link)
+
+MALI_STATIC_INLINE struct mali_page_directory *mali_session_get_page_directory(struct mali_session_data *session)
+{
+	return session->page_directory;
+}
+
+MALI_STATIC_INLINE void mali_session_memory_lock(struct mali_session_data *session)
+{
+	MALI_DEBUG_ASSERT_POINTER(session);
+	_mali_osk_mutex_wait(session->memory_lock);
+}
+
+MALI_STATIC_INLINE void mali_session_memory_unlock(struct mali_session_data *session)
+{
+	MALI_DEBUG_ASSERT_POINTER(session);
+	_mali_osk_mutex_signal(session->memory_lock);
+}
+
+MALI_STATIC_INLINE void mali_session_send_notification(struct mali_session_data *session, _mali_osk_notification_t *object)
+{
+	_mali_osk_notification_queue_send(session->ioctl_queue, object);
+}
+
+#if defined(CONFIG_MALI_DVFS)
+
+MALI_STATIC_INLINE void mali_session_inc_num_window_jobs(struct mali_session_data *session)
+{
+	MALI_DEBUG_ASSERT_POINTER(session);
+	_mali_osk_atomic_inc(&session->number_of_window_jobs);
+}
+
+/*
+ * Get the max completed window jobs from all active session,
+ * which will be used in  window render frame per sec calculate
+ */
+u32 mali_session_max_window_num(void);
+
+#endif
+
+void mali_session_memory_tracking(_mali_osk_print_ctx *print_ctx);
+
+#endif /* __MALI_SESSION_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_soft_job.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_soft_job.c
@@ -0,0 +1,440 @@
+/*
+ * Copyright (C) 2013-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_soft_job.h"
+#include "mali_osk.h"
+#include "mali_timeline.h"
+#include "mali_session.h"
+#include "mali_kernel_common.h"
+#include "mali_uk_types.h"
+#include "mali_scheduler.h"
+#include "mali_executor.h"
+
+MALI_STATIC_INLINE void mali_soft_job_system_lock(struct mali_soft_job_system *system)
+{
+	MALI_DEBUG_ASSERT_POINTER(system);
+	_mali_osk_spinlock_irq_lock(system->lock);
+	MALI_DEBUG_PRINT(5, ("Mali Soft Job: soft system %p lock taken\n", system));
+	MALI_DEBUG_ASSERT(0 == system->lock_owner);
+	MALI_DEBUG_CODE(system->lock_owner = _mali_osk_get_tid());
+}
+
+MALI_STATIC_INLINE void mali_soft_job_system_unlock(struct mali_soft_job_system *system)
+{
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_PRINT(5, ("Mali Soft Job: releasing soft system %p lock\n", system));
+	MALI_DEBUG_ASSERT(_mali_osk_get_tid() == system->lock_owner);
+	MALI_DEBUG_CODE(system->lock_owner = 0);
+	_mali_osk_spinlock_irq_unlock(system->lock);
+}
+
+#if defined(DEBUG)
+MALI_STATIC_INLINE void mali_soft_job_system_assert_locked(struct mali_soft_job_system *system)
+{
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT(_mali_osk_get_tid() == system->lock_owner);
+}
+#define MALI_ASSERT_SOFT_JOB_SYSTEM_LOCKED(system) mali_soft_job_system_assert_locked(system)
+#else
+#define MALI_ASSERT_SOFT_JOB_SYSTEM_LOCKED(system)
+#endif /* defined(DEBUG) */
+
+struct mali_soft_job_system *mali_soft_job_system_create(struct mali_session_data *session)
+{
+	struct mali_soft_job_system *system;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	system = (struct mali_soft_job_system *) _mali_osk_calloc(1, sizeof(struct mali_soft_job_system));
+	if (NULL == system) {
+		return NULL;
+	}
+
+	system->session = session;
+
+	system->lock = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_ORDERED, _MALI_OSK_LOCK_ORDER_SCHEDULER);
+	if (NULL == system->lock) {
+		mali_soft_job_system_destroy(system);
+		return NULL;
+	}
+	system->lock_owner = 0;
+	system->last_job_id = 0;
+
+	_MALI_OSK_INIT_LIST_HEAD(&(system->jobs_used));
+
+	return system;
+}
+
+void mali_soft_job_system_destroy(struct mali_soft_job_system *system)
+{
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	/* All jobs should be free at this point. */
+	MALI_DEBUG_ASSERT(_mali_osk_list_empty(&(system->jobs_used)));
+
+	if (NULL != system) {
+		if (NULL != system->lock) {
+			_mali_osk_spinlock_irq_term(system->lock);
+		}
+		_mali_osk_free(system);
+	}
+}
+
+static void mali_soft_job_system_free_job(struct mali_soft_job_system *system, struct mali_soft_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_soft_job_system_lock(job->system);
+
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_INVALID_ID != job->id);
+	MALI_DEBUG_ASSERT(system == job->system);
+
+	_mali_osk_list_del(&(job->system_list));
+
+	mali_soft_job_system_unlock(job->system);
+
+	_mali_osk_free(job);
+}
+
+MALI_STATIC_INLINE struct mali_soft_job *mali_soft_job_system_lookup_job(struct mali_soft_job_system *system, u32 job_id)
+{
+	struct mali_soft_job *job, *tmp;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_ASSERT_SOFT_JOB_SYSTEM_LOCKED(system);
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp, &system->jobs_used, struct mali_soft_job, system_list) {
+		if (job->id == job_id)
+			return job;
+	}
+
+	return NULL;
+}
+
+void mali_soft_job_destroy(struct mali_soft_job *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(job->system);
+
+	MALI_DEBUG_PRINT(4, ("Mali Soft Job: destroying soft job %u (0x%08X)\n", job->id, job));
+
+	if (NULL != job) {
+		if (0 < _mali_osk_atomic_dec_return(&job->refcount)) return;
+
+		_mali_osk_atomic_term(&job->refcount);
+
+		if (NULL != job->activated_notification) {
+			_mali_osk_notification_delete(job->activated_notification);
+			job->activated_notification = NULL;
+		}
+
+		mali_soft_job_system_free_job(job->system, job);
+	}
+}
+
+struct mali_soft_job *mali_soft_job_create(struct mali_soft_job_system *system, mali_soft_job_type type, u64 user_job)
+{
+	struct mali_soft_job *job;
+	_mali_osk_notification_t *notification = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT((MALI_SOFT_JOB_TYPE_USER_SIGNALED == type) ||
+			  (MALI_SOFT_JOB_TYPE_SELF_SIGNALED == type));
+
+	notification = _mali_osk_notification_create(_MALI_NOTIFICATION_SOFT_ACTIVATED, sizeof(_mali_uk_soft_job_activated_s));
+	if (unlikely(NULL == notification)) {
+		MALI_PRINT_ERROR(("Mali Soft Job: failed to allocate notification"));
+		return NULL;
+	}
+
+	job = _mali_osk_malloc(sizeof(struct mali_soft_job));
+	if (unlikely(NULL == job)) {
+		MALI_DEBUG_PRINT(2, ("Mali Soft Job: system alloc job failed. \n"));
+		return NULL;
+	}
+
+	mali_soft_job_system_lock(system);
+
+	job->system = system;
+	job->id = system->last_job_id++;
+	job->state = MALI_SOFT_JOB_STATE_ALLOCATED;
+
+	_mali_osk_list_add(&(job->system_list), &(system->jobs_used));
+
+	job->type = type;
+	job->user_job = user_job;
+	job->activated = MALI_FALSE;
+
+	job->activated_notification = notification;
+
+	_mali_osk_atomic_init(&job->refcount, 1);
+
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_ALLOCATED == job->state);
+	MALI_DEBUG_ASSERT(system == job->system);
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_INVALID_ID != job->id);
+
+	mali_soft_job_system_unlock(system);
+
+	return job;
+}
+
+mali_timeline_point mali_soft_job_start(struct mali_soft_job *job, struct mali_timeline_fence *fence)
+{
+	mali_timeline_point point;
+	struct mali_soft_job_system *system;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	MALI_DEBUG_ASSERT_POINTER(job->system);
+	system = job->system;
+
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+	MALI_DEBUG_ASSERT_POINTER(system->session->timeline_system);
+
+	mali_soft_job_system_lock(system);
+
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_ALLOCATED == job->state);
+	job->state = MALI_SOFT_JOB_STATE_STARTED;
+
+	mali_soft_job_system_unlock(system);
+
+	MALI_DEBUG_PRINT(4, ("Mali Soft Job: starting soft job %u (0x%08X)\n", job->id, job));
+
+	mali_timeline_tracker_init(&job->tracker, MALI_TIMELINE_TRACKER_SOFT, fence, job);
+	point = mali_timeline_system_add_tracker(system->session->timeline_system, &job->tracker, MALI_TIMELINE_SOFT);
+
+	return point;
+}
+
+static mali_bool mali_soft_job_is_activated(void *data)
+{
+	struct mali_soft_job *job;
+
+	job = (struct mali_soft_job *) data;
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	return job->activated;
+}
+
+_mali_osk_errcode_t mali_soft_job_system_signal_job(struct mali_soft_job_system *system, u32 job_id)
+{
+	struct mali_soft_job *job;
+	struct mali_timeline_system *timeline_system;
+	mali_scheduler_mask schedule_mask;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_soft_job_system_lock(system);
+
+	job = mali_soft_job_system_lookup_job(system, job_id);
+
+	if ((NULL == job) || (MALI_SOFT_JOB_TYPE_USER_SIGNALED != job->type)
+	    || !(MALI_SOFT_JOB_STATE_STARTED == job->state || MALI_SOFT_JOB_STATE_TIMED_OUT == job->state)) {
+		mali_soft_job_system_unlock(system);
+		MALI_PRINT_ERROR(("Mali Soft Job: invalid soft job id %u", job_id));
+		return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	}
+
+	if (MALI_SOFT_JOB_STATE_TIMED_OUT == job->state) {
+		job->state = MALI_SOFT_JOB_STATE_SIGNALED;
+		mali_soft_job_system_unlock(system);
+
+		MALI_DEBUG_ASSERT(MALI_TRUE == job->activated);
+		MALI_DEBUG_PRINT(4, ("Mali Soft Job: soft job %u (0x%08X) was timed out\n", job->id, job));
+		mali_soft_job_destroy(job);
+
+		return _MALI_OSK_ERR_TIMEOUT;
+	}
+
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_STARTED == job->state);
+
+	job->state = MALI_SOFT_JOB_STATE_SIGNALED;
+	mali_soft_job_system_unlock(system);
+
+	/* Since the job now is in signaled state, timeouts from the timeline system will be
+	 * ignored, and it is not possible to signal this job again. */
+
+	timeline_system = system->session->timeline_system;
+	MALI_DEBUG_ASSERT_POINTER(timeline_system);
+
+	/* Wait until activated. */
+	_mali_osk_wait_queue_wait_event(timeline_system->wait_queue, mali_soft_job_is_activated, (void *) job);
+
+	MALI_DEBUG_PRINT(4, ("Mali Soft Job: signaling soft job %u (0x%08X)\n", job->id, job));
+
+	schedule_mask = mali_timeline_tracker_release(&job->tracker);
+	mali_executor_schedule_from_mask(schedule_mask, MALI_FALSE);
+
+	mali_soft_job_destroy(job);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+static void mali_soft_job_send_activated_notification(struct mali_soft_job *job)
+{
+	if (NULL != job->activated_notification) {
+		_mali_uk_soft_job_activated_s *res = job->activated_notification->result_buffer;
+		res->user_job = job->user_job;
+		mali_session_send_notification(job->system->session, job->activated_notification);
+	}
+	job->activated_notification = NULL;
+}
+
+mali_scheduler_mask mali_soft_job_system_activate_job(struct mali_soft_job *job)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(job->system);
+	MALI_DEBUG_ASSERT_POINTER(job->system->session);
+
+	MALI_DEBUG_PRINT(4, ("Mali Soft Job: Timeline activation for soft job %u (0x%08X).\n", job->id, job));
+
+	mali_soft_job_system_lock(job->system);
+
+	if (unlikely(job->system->session->is_aborting)) {
+		MALI_DEBUG_PRINT(3, ("Mali Soft Job: Soft job %u (0x%08X) activated while session is aborting.\n", job->id, job));
+
+		mali_soft_job_system_unlock(job->system);
+
+		/* Since we are in shutdown, we can ignore the scheduling bitmask. */
+		mali_timeline_tracker_release(&job->tracker);
+		mali_soft_job_destroy(job);
+		return schedule_mask;
+	}
+
+	/* Send activated notification. */
+	mali_soft_job_send_activated_notification(job);
+
+	/* Wake up sleeping signaler. */
+	job->activated = MALI_TRUE;
+
+	/* If job type is self signaled, release tracker, move soft job to free list, and scheduler at once */
+	if (MALI_SOFT_JOB_TYPE_SELF_SIGNALED == job->type) {
+		MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_STARTED == job->state);
+
+		job->state = MALI_SOFT_JOB_STATE_SIGNALED;
+		mali_soft_job_system_unlock(job->system);
+
+		schedule_mask |= mali_timeline_tracker_release(&job->tracker);
+
+		mali_soft_job_destroy(job);
+	} else {
+		_mali_osk_wait_queue_wake_up(job->tracker.system->wait_queue);
+
+		mali_soft_job_system_unlock(job->system);
+	}
+
+	return schedule_mask;
+}
+
+mali_scheduler_mask mali_soft_job_system_timeout_job(struct mali_soft_job *job)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+	MALI_DEBUG_ASSERT_POINTER(job->system);
+	MALI_DEBUG_ASSERT_POINTER(job->system->session);
+	MALI_DEBUG_ASSERT(MALI_TRUE == job->activated);
+
+	MALI_DEBUG_PRINT(4, ("Mali Soft Job: Timeline timeout for soft job %u (0x%08X).\n", job->id, job));
+
+	mali_soft_job_system_lock(job->system);
+
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_STARTED  == job->state ||
+			  MALI_SOFT_JOB_STATE_SIGNALED == job->state);
+
+	if (unlikely(job->system->session->is_aborting)) {
+		/* The session is aborting.  This job will be released and destroyed by @ref
+		 * mali_soft_job_system_abort(). */
+		mali_soft_job_system_unlock(job->system);
+
+		return MALI_SCHEDULER_MASK_EMPTY;
+	}
+
+	if (MALI_SOFT_JOB_STATE_STARTED != job->state) {
+		MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_SIGNALED == job->state);
+
+		/* The job is about to be signaled, ignore timeout. */
+		MALI_DEBUG_PRINT(4, ("Mali Soft Job: Timeout on soft job %u (0x%08X) in signaled state.\n", job->id, job));
+		mali_soft_job_system_unlock(job->system);
+		return schedule_mask;
+	}
+
+	MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_STARTED == job->state);
+
+	job->state = MALI_SOFT_JOB_STATE_TIMED_OUT;
+	_mali_osk_atomic_inc(&job->refcount);
+
+	mali_soft_job_system_unlock(job->system);
+
+	schedule_mask = mali_timeline_tracker_release(&job->tracker);
+
+	mali_soft_job_destroy(job);
+
+	return schedule_mask;
+}
+
+void mali_soft_job_system_abort(struct mali_soft_job_system *system)
+{
+	struct mali_soft_job *job, *tmp;
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(jobs);
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+	MALI_DEBUG_ASSERT(system->session->is_aborting);
+
+	MALI_DEBUG_PRINT(3, ("Mali Soft Job: Aborting soft job system for session 0x%08X.\n", system->session));
+
+	mali_soft_job_system_lock(system);
+
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp, &system->jobs_used, struct mali_soft_job, system_list) {
+		MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_STARTED   == job->state ||
+				  MALI_SOFT_JOB_STATE_TIMED_OUT == job->state);
+
+		if (MALI_SOFT_JOB_STATE_STARTED == job->state) {
+			/* If the job has been activated, we have to release the tracker and destroy
+			 * the job.  If not, the tracker will be released and the job destroyed when
+			 * it is activated. */
+			if (MALI_TRUE == job->activated) {
+				MALI_DEBUG_PRINT(3, ("Mali Soft Job: Aborting unsignaled soft job %u (0x%08X).\n", job->id, job));
+
+				job->state = MALI_SOFT_JOB_STATE_SIGNALED;
+				_mali_osk_list_move(&job->system_list, &jobs);
+			}
+		} else if (MALI_SOFT_JOB_STATE_TIMED_OUT == job->state) {
+			MALI_DEBUG_PRINT(3, ("Mali Soft Job: Aborting timed out soft job %u (0x%08X).\n", job->id, job));
+
+			/* We need to destroy this soft job. */
+			_mali_osk_list_move(&job->system_list, &jobs);
+		}
+	}
+
+	mali_soft_job_system_unlock(system);
+
+	/* Release and destroy jobs. */
+	_MALI_OSK_LIST_FOREACHENTRY(job, tmp, &jobs, struct mali_soft_job, system_list) {
+		MALI_DEBUG_ASSERT(MALI_SOFT_JOB_STATE_SIGNALED  == job->state ||
+				  MALI_SOFT_JOB_STATE_TIMED_OUT == job->state);
+
+		if (MALI_SOFT_JOB_STATE_SIGNALED == job->state) {
+			mali_timeline_tracker_release(&job->tracker);
+		}
+
+		/* Move job back to used list before destroying. */
+		_mali_osk_list_move(&job->system_list, &system->jobs_used);
+
+		mali_soft_job_destroy(job);
+	}
+
+	mali_executor_schedule_from_mask(MALI_SCHEDULER_MASK_ALL, MALI_FALSE);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_soft_job.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_soft_job.h
@@ -0,0 +1,190 @@
+/*
+ * Copyright (C) 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_SOFT_JOB_H__
+#define __MALI_SOFT_JOB_H__
+
+#include "mali_osk.h"
+
+#include "mali_timeline.h"
+
+struct mali_timeline_fence;
+struct mali_session_data;
+struct mali_soft_job;
+struct mali_soft_job_system;
+
+/**
+ * Soft job types.
+ *
+ * Soft jobs of type MALI_SOFT_JOB_TYPE_USER_SIGNALED will only complete after activation if either
+ * they are signaled by user-space (@ref mali_soft_job_system_signaled_job) or if they are timed out
+ * by the Timeline system.
+ * Soft jobs of type MALI_SOFT_JOB_TYPE_SELF_SIGNALED will release job resource automatically
+ * in kernel when the job is activated.
+ */
+typedef enum mali_soft_job_type {
+	MALI_SOFT_JOB_TYPE_SELF_SIGNALED,
+	MALI_SOFT_JOB_TYPE_USER_SIGNALED,
+} mali_soft_job_type;
+
+/**
+ * Soft job state.
+ *
+ * mali_soft_job_system_start_job a job will first be allocated.The job's state set to MALI_SOFT_JOB_STATE_ALLOCATED.
+ * Once the job is added to the timeline system, the state changes to MALI_SOFT_JOB_STATE_STARTED.
+ *
+ * For soft jobs of type MALI_SOFT_JOB_TYPE_USER_SIGNALED the state is changed to
+ * MALI_SOFT_JOB_STATE_SIGNALED when @ref mali_soft_job_system_signal_job is called and the soft
+ * job's state is MALI_SOFT_JOB_STATE_STARTED or MALI_SOFT_JOB_STATE_TIMED_OUT.
+ *
+ * If a soft job of type MALI_SOFT_JOB_TYPE_USER_SIGNALED is timed out before being signaled, the
+ * state is changed to MALI_SOFT_JOB_STATE_TIMED_OUT.  This can only happen to soft jobs in state
+ * MALI_SOFT_JOB_STATE_STARTED.
+ *
+ */
+typedef enum mali_soft_job_state {
+	MALI_SOFT_JOB_STATE_ALLOCATED,
+	MALI_SOFT_JOB_STATE_STARTED,
+	MALI_SOFT_JOB_STATE_SIGNALED,
+	MALI_SOFT_JOB_STATE_TIMED_OUT,
+} mali_soft_job_state;
+
+#define MALI_SOFT_JOB_INVALID_ID ((u32) -1)
+
+/**
+ * Soft job struct.
+ *
+ * Soft job can be used to represent any kind of CPU work done in kernel-space.
+ */
+typedef struct mali_soft_job {
+	mali_soft_job_type            type;                   /**< Soft job type.  Must be one of MALI_SOFT_JOB_TYPE_*. */
+	u64                           user_job;               /**< Identifier for soft job in user space. */
+	_mali_osk_atomic_t            refcount;               /**< Soft jobs are reference counted to prevent premature deletion. */
+	struct mali_timeline_tracker  tracker;                /**< Timeline tracker for soft job. */
+	mali_bool                     activated;              /**< MALI_TRUE if the job has been activated, MALI_FALSE if not. */
+	_mali_osk_notification_t     *activated_notification; /**< Pre-allocated notification object for ACTIVATED_NOTIFICATION. */
+
+	/* Protected by soft job system lock. */
+	u32                           id;                     /**< Used by user-space to find corresponding soft job in kernel-space. */
+	mali_soft_job_state           state;                  /**< State of soft job, must be one of MALI_SOFT_JOB_STATE_*. */
+	struct mali_soft_job_system  *system;                 /**< The soft job system this job is in. */
+	_mali_osk_list_t              system_list;            /**< List element used by soft job system. */
+} mali_soft_job;
+
+/**
+ * Per-session soft job system.
+ *
+ * The soft job system is used to manage all soft jobs that belongs to a session.
+ */
+typedef struct mali_soft_job_system {
+	struct mali_session_data *session;                    /**< The session this soft job system belongs to. */
+	_MALI_OSK_LIST_HEAD(jobs_used);                       /**< List of all allocated soft jobs. */
+
+	_mali_osk_spinlock_irq_t *lock;                       /**< Lock used to protect soft job system and its soft jobs. */
+	u32 lock_owner;                                       /**< Contains tid of thread that locked the system or 0, if not locked. */
+	u32 last_job_id;                                      /**< Recored the last job id protected by lock. */
+} mali_soft_job_system;
+
+/**
+ * Create a soft job system.
+ *
+ * @param session The session this soft job system will belong to.
+ * @return The new soft job system, or NULL if unsuccessful.
+ */
+struct mali_soft_job_system *mali_soft_job_system_create(struct mali_session_data *session);
+
+/**
+ * Destroy a soft job system.
+ *
+ * @note The soft job must not have any started or activated jobs.  Call @ref
+ * mali_soft_job_system_abort first.
+ *
+ * @param system The soft job system we are destroying.
+ */
+void mali_soft_job_system_destroy(struct mali_soft_job_system *system);
+
+/**
+ * Create a soft job.
+ *
+ * @param system Soft job system to create soft job from.
+ * @param type Type of the soft job.
+ * @param user_job Identifier for soft job in user space.
+ * @return New soft job if successful, NULL if not.
+ */
+struct mali_soft_job *mali_soft_job_create(struct mali_soft_job_system *system, mali_soft_job_type type, u64 user_job);
+
+/**
+ * Destroy soft job.
+ *
+ * @param job Soft job to destroy.
+ */
+void mali_soft_job_destroy(struct mali_soft_job *job);
+
+/**
+ * Start a soft job.
+ *
+ * The soft job will be added to the Timeline system which will then activate it after all
+ * dependencies have been resolved.
+ *
+ * Create soft jobs with @ref mali_soft_job_create before starting them.
+ *
+ * @param job Soft job to start.
+ * @param fence Fence representing dependencies for this soft job.
+ * @return Point on soft job timeline.
+ */
+mali_timeline_point mali_soft_job_start(struct mali_soft_job *job, struct mali_timeline_fence *fence);
+
+/**
+ * Use by user-space to signal that a soft job has completed.
+ *
+ * @note Only valid for soft jobs with type MALI_SOFT_JOB_TYPE_USER_SIGNALED.
+ *
+ * @note The soft job must be in state MALI_SOFT_JOB_STATE_STARTED for the signal to be successful.
+ *
+ * @note If the soft job was signaled successfully, or it received a time out, the soft job will be
+ * destroyed after this call and should no longer be used.
+ *
+ * @note This function will block until the soft job has been activated.
+ *
+ * @param system The soft job system the job was started in.
+ * @param job_id ID of soft job we are signaling.
+ *
+ * @return _MALI_OSK_ERR_ITEM_NOT_FOUND if the soft job ID was invalid, _MALI_OSK_ERR_TIMEOUT if the
+ * soft job was timed out or _MALI_OSK_ERR_OK if we successfully signaled the soft job.
+ */
+_mali_osk_errcode_t mali_soft_job_system_signal_job(struct mali_soft_job_system *system, u32 job_id);
+
+/**
+ * Used by the Timeline system to activate a soft job.
+ *
+ * @param job The soft job that is being activated.
+ * @return A scheduling bitmask.
+ */
+mali_scheduler_mask mali_soft_job_system_activate_job(struct mali_soft_job *job);
+
+/**
+ * Used by the Timeline system to timeout a soft job.
+ *
+ * A soft job is timed out if it completes or is signaled later than MALI_TIMELINE_TIMEOUT_HZ after
+ * activation.
+ *
+ * @param job The soft job that is being timed out.
+ * @return A scheduling bitmask.
+ */
+mali_scheduler_mask mali_soft_job_system_timeout_job(struct mali_soft_job *job);
+
+/**
+ * Used to cleanup activated soft jobs in the soft job system on session abort.
+ *
+ * @param system The soft job system that is being aborted.
+ */
+void mali_soft_job_system_abort(struct mali_soft_job_system *system);
+
+#endif /* __MALI_SOFT_JOB_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_spinlock_reentrant.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_spinlock_reentrant.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_spinlock_reentrant.h"
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+struct mali_spinlock_reentrant *mali_spinlock_reentrant_init(_mali_osk_lock_order_t lock_order)
+{
+	struct mali_spinlock_reentrant *spinlock;
+
+	spinlock = _mali_osk_calloc(1, sizeof(struct mali_spinlock_reentrant));
+	if (NULL == spinlock) {
+		return NULL;
+	}
+
+	spinlock->lock = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_ORDERED, lock_order);
+	if (NULL == spinlock->lock) {
+		mali_spinlock_reentrant_term(spinlock);
+		return NULL;
+	}
+
+	return spinlock;
+}
+
+void mali_spinlock_reentrant_term(struct mali_spinlock_reentrant *spinlock)
+{
+	MALI_DEBUG_ASSERT_POINTER(spinlock);
+	MALI_DEBUG_ASSERT(0 == spinlock->counter && 0 == spinlock->owner);
+
+	if (NULL != spinlock->lock) {
+		_mali_osk_spinlock_irq_term(spinlock->lock);
+	}
+
+	_mali_osk_free(spinlock);
+}
+
+void mali_spinlock_reentrant_wait(struct mali_spinlock_reentrant *spinlock, u32 tid)
+{
+	MALI_DEBUG_ASSERT_POINTER(spinlock);
+	MALI_DEBUG_ASSERT_POINTER(spinlock->lock);
+	MALI_DEBUG_ASSERT(0 != tid);
+
+	MALI_DEBUG_PRINT(5, ("%s ^\n", __FUNCTION__));
+
+	if (tid != spinlock->owner) {
+		_mali_osk_spinlock_irq_lock(spinlock->lock);
+		MALI_DEBUG_ASSERT(0 == spinlock->owner && 0 == spinlock->counter);
+		spinlock->owner = tid;
+	}
+
+	MALI_DEBUG_PRINT(5, ("%s v\n", __FUNCTION__));
+
+	++spinlock->counter;
+}
+
+void mali_spinlock_reentrant_signal(struct mali_spinlock_reentrant *spinlock, u32 tid)
+{
+	MALI_DEBUG_ASSERT_POINTER(spinlock);
+	MALI_DEBUG_ASSERT_POINTER(spinlock->lock);
+	MALI_DEBUG_ASSERT(0 != tid && tid == spinlock->owner);
+
+	--spinlock->counter;
+	if (0 == spinlock->counter) {
+		spinlock->owner = 0;
+		MALI_DEBUG_PRINT(5, ("%s release last\n", __FUNCTION__));
+		_mali_osk_spinlock_irq_unlock(spinlock->lock);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_spinlock_reentrant.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_spinlock_reentrant.h
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_SPINLOCK_REENTRANT_H__
+#define __MALI_SPINLOCK_REENTRANT_H__
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+/**
+ * Reentrant spinlock.
+ */
+struct mali_spinlock_reentrant {
+	_mali_osk_spinlock_irq_t *lock;
+	u32               owner;
+	u32               counter;
+};
+
+/**
+ * Create a new reentrant spinlock.
+ *
+ * @param lock_order Lock order.
+ * @return New reentrant spinlock.
+ */
+struct mali_spinlock_reentrant *mali_spinlock_reentrant_init(_mali_osk_lock_order_t lock_order);
+
+/**
+ * Terminate reentrant spinlock and free any associated resources.
+ *
+ * @param spinlock Reentrant spinlock to terminate.
+ */
+void mali_spinlock_reentrant_term(struct mali_spinlock_reentrant *spinlock);
+
+/**
+ * Wait for reentrant spinlock to be signaled.
+ *
+ * @param spinlock Reentrant spinlock.
+ * @param tid Thread ID.
+ */
+void mali_spinlock_reentrant_wait(struct mali_spinlock_reentrant *spinlock, u32 tid);
+
+/**
+ * Signal reentrant spinlock.
+ *
+ * @param spinlock Reentrant spinlock.
+ * @param tid Thread ID.
+ */
+void mali_spinlock_reentrant_signal(struct mali_spinlock_reentrant *spinlock, u32 tid);
+
+/**
+ * Check if thread is holding reentrant spinlock.
+ *
+ * @param spinlock Reentrant spinlock.
+ * @param tid Thread ID.
+ * @return MALI_TRUE if thread is holding spinlock, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_spinlock_reentrant_is_held(struct mali_spinlock_reentrant *spinlock, u32 tid)
+{
+	MALI_DEBUG_ASSERT_POINTER(spinlock->lock);
+	return (tid == spinlock->owner && 0 < spinlock->counter);
+}
+
+#endif /* __MALI_SPINLOCK_REENTRANT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_timeline.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_timeline.c
@@ -0,0 +1,1965 @@
+/*
+ * Copyright (C) 2013-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/file.h>
+#include "mali_timeline.h"
+#include "mali_kernel_common.h"
+#include "mali_scheduler.h"
+#include "mali_soft_job.h"
+#include "mali_timeline_fence_wait.h"
+#include "mali_timeline_sync_fence.h"
+#include "mali_executor.h"
+#include "mali_pp_job.h"
+
+#define MALI_TIMELINE_SYSTEM_LOCKED(system) (mali_spinlock_reentrant_is_held((system)->spinlock, _mali_osk_get_tid()))
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+_mali_osk_wq_work_t *sync_fence_callback_work_t = NULL;
+_mali_osk_spinlock_irq_t *sync_fence_callback_list_lock = NULL;
+static _MALI_OSK_LIST_HEAD_STATIC_INIT(sync_fence_callback_queue);
+#endif
+
+/*
+ * Following three elements are used to record how many
+ * gp, physical pp or virtual pp jobs are delayed in the whole
+ * timeline system, we can use these three value to decide
+ * if need to deactivate idle group.
+ */
+_mali_osk_atomic_t gp_tracker_count;
+_mali_osk_atomic_t phy_pp_tracker_count;
+_mali_osk_atomic_t virt_pp_tracker_count;
+
+static mali_scheduler_mask mali_timeline_system_release_waiter(struct mali_timeline_system *system,
+		struct mali_timeline_waiter *waiter);
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+#include <linux/version.h>
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3,5,0)
+#include <linux/list.h>
+#include <linux/workqueue.h>
+#include <linux/spinlock.h>
+
+struct mali_deferred_fence_put_entry {
+	struct hlist_node list;
+	struct sync_fence *fence;
+};
+
+static HLIST_HEAD(mali_timeline_sync_fence_to_free_list);
+static DEFINE_SPINLOCK(mali_timeline_sync_fence_to_free_lock);
+
+static void put_sync_fences(struct work_struct *ignore)
+{
+	struct hlist_head list;
+	struct hlist_node *tmp, *pos;
+	unsigned long flags;
+	struct mali_deferred_fence_put_entry *o;
+
+	spin_lock_irqsave(&mali_timeline_sync_fence_to_free_lock, flags);
+	hlist_move_list(&mali_timeline_sync_fence_to_free_list, &list);
+	spin_unlock_irqrestore(&mali_timeline_sync_fence_to_free_lock, flags);
+
+	hlist_for_each_entry_safe(o, pos, tmp, &list, list) {
+		sync_fence_put(o->fence);
+		kfree(o);
+	}
+}
+
+static DECLARE_DELAYED_WORK(delayed_sync_fence_put, put_sync_fences);
+#endif /* LINUX_VERSION_CODE < KERNEL_VERSION(3,5,0) */
+
+/* Callback that is called when a sync fence a tracker is waiting on is signaled. */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static void mali_timeline_sync_fence_callback(struct sync_fence *sync_fence, struct sync_fence_waiter *sync_fence_waiter)
+#else
+static void mali_timeline_sync_fence_callback(struct mali_internal_sync_fence *sync_fence, struct mali_internal_sync_fence_waiter *sync_fence_waiter)
+#endif
+{
+	struct mali_timeline_tracker *tracker;
+
+	MALI_IGNORE(sync_fence);
+	MALI_DEBUG_ASSERT_POINTER(sync_fence_waiter);
+
+	tracker = _MALI_OSK_CONTAINER_OF(sync_fence_waiter, struct mali_timeline_tracker, sync_fence_waiter);
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	_mali_osk_spinlock_irq_lock(sync_fence_callback_list_lock);
+	_mali_osk_list_addtail(&tracker->sync_fence_signal_list, &sync_fence_callback_queue);
+	_mali_osk_spinlock_irq_unlock(sync_fence_callback_list_lock);
+
+	_mali_osk_wq_schedule_work(sync_fence_callback_work_t);
+}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+static mali_scheduler_mask mali_timeline_tracker_time_out(struct mali_timeline_tracker *tracker)
+{
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_TRACKER_SOFT == tracker->type);
+
+	return mali_soft_job_system_timeout_job((struct mali_soft_job *) tracker->job);
+}
+
+static void mali_timeline_timer_callback(void *data)
+{
+	struct mali_timeline_system *system;
+	struct mali_timeline_tracker *tracker;
+	struct mali_timeline *timeline;
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+	u32 tid = _mali_osk_get_tid();
+
+	timeline = (struct mali_timeline *) data;
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	system = timeline->system;
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	if (!system->timer_enabled) {
+		mali_spinlock_reentrant_signal(system->spinlock, tid);
+		return;
+	}
+
+	tracker = timeline->tracker_tail;
+	timeline->timer_active = MALI_FALSE;
+
+	if (NULL != tracker && MALI_TRUE == tracker->timer_active) {
+		/* This is likely the delayed work that has been schedule out before cancelled. */
+		if (MALI_TIMELINE_TIMEOUT_HZ > (_mali_osk_time_tickcount() - tracker->os_tick_activate)) {
+			mali_spinlock_reentrant_signal(system->spinlock, tid);
+			return;
+		}
+
+		schedule_mask = mali_timeline_tracker_time_out(tracker);
+		tracker->timer_active = MALI_FALSE;
+	} else {
+		MALI_PRINT_ERROR(("Mali Timeline: Soft job timer callback without a waiting tracker.\n"));
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	mali_executor_schedule_from_mask(schedule_mask, MALI_FALSE);
+}
+
+void mali_timeline_system_stop_timer(struct mali_timeline_system *system)
+{
+	u32 i;
+	u32 tid = _mali_osk_get_tid();
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+	system->timer_enabled = MALI_FALSE;
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline = system->timelines[i];
+
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		if (NULL != timeline->delayed_work) {
+			_mali_osk_wq_delayed_cancel_work_sync(timeline->delayed_work);
+			timeline->timer_active = MALI_FALSE;
+		}
+	}
+}
+
+static void mali_timeline_destroy(struct mali_timeline *timeline)
+{
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	if (NULL != timeline) {
+		/* Assert that the timeline object has been properly cleaned up before destroying it. */
+		MALI_DEBUG_ASSERT(timeline->point_oldest == timeline->point_next);
+		MALI_DEBUG_ASSERT(NULL == timeline->tracker_head);
+		MALI_DEBUG_ASSERT(NULL == timeline->tracker_tail);
+		MALI_DEBUG_ASSERT(NULL == timeline->waiter_head);
+		MALI_DEBUG_ASSERT(NULL == timeline->waiter_tail);
+		MALI_DEBUG_ASSERT(NULL != timeline->system);
+		MALI_DEBUG_ASSERT(MALI_TIMELINE_MAX > timeline->id);
+
+		if (NULL != timeline->delayed_work) {
+			_mali_osk_wq_delayed_cancel_work_sync(timeline->delayed_work);
+			_mali_osk_wq_delayed_delete_work_nonflush(timeline->delayed_work);
+		}
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+		if (NULL != timeline->sync_tl) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+			sync_timeline_destroy(timeline->sync_tl);
+#else
+			mali_internal_sync_timeline_destroy(timeline->sync_tl);
+#endif
+		}
+#else
+		_mali_osk_free(timeline);
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+	}
+}
+
+static struct mali_timeline *mali_timeline_create(struct mali_timeline_system *system, enum mali_timeline_id id)
+{
+	struct mali_timeline *timeline;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT(id < MALI_TIMELINE_MAX);
+
+	timeline = (struct mali_timeline *) _mali_osk_calloc(1, sizeof(struct mali_timeline));
+	if (NULL == timeline) {
+		return NULL;
+	}
+
+	/* Initially the timeline is empty. */
+#if defined(MALI_TIMELINE_DEBUG_START_POINT)
+	/* Start the timeline a bit before wrapping when debugging. */
+	timeline->point_next = UINT_MAX - MALI_TIMELINE_MAX_POINT_SPAN - 128;
+#else
+	timeline->point_next = 1;
+#endif
+	timeline->point_oldest = timeline->point_next;
+
+	/* The tracker and waiter lists will initially be empty. */
+
+	timeline->system = system;
+	timeline->id = id;
+
+	timeline->delayed_work = _mali_osk_wq_delayed_create_work(mali_timeline_timer_callback, timeline);
+	if (NULL == timeline->delayed_work) {
+		mali_timeline_destroy(timeline);
+		return NULL;
+	}
+
+	timeline->timer_active = MALI_FALSE;
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	{
+		char timeline_name[32];
+
+		switch (id) {
+		case MALI_TIMELINE_GP:
+			_mali_osk_snprintf(timeline_name, 32, "mali-%u-gp", _mali_osk_get_pid());
+			break;
+		case MALI_TIMELINE_PP:
+			_mali_osk_snprintf(timeline_name, 32, "mali-%u-pp", _mali_osk_get_pid());
+			break;
+		case MALI_TIMELINE_SOFT:
+			_mali_osk_snprintf(timeline_name, 32, "mali-%u-soft", _mali_osk_get_pid());
+			break;
+		default:
+			MALI_PRINT_ERROR(("Mali Timeline: Invalid timeline id %d\n", id));
+			mali_timeline_destroy(timeline);
+			return NULL;
+		}
+
+		timeline->destroyed = MALI_FALSE;
+
+		timeline->sync_tl = mali_sync_timeline_create(timeline, timeline_name);
+		if (NULL == timeline->sync_tl) {
+			mali_timeline_destroy(timeline);
+			return NULL;
+		}
+
+		timeline->spinlock = mali_spinlock_reentrant_init(_MALI_OSK_LOCK_ORDER_TIMELINE_SYSTEM);
+		if (NULL == timeline->spinlock) {
+			mali_timeline_destroy(timeline);
+			return NULL;
+		}
+	}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	return timeline;
+}
+
+static void mali_timeline_insert_tracker(struct mali_timeline *timeline, struct mali_timeline_tracker *tracker)
+{
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	if (mali_timeline_is_full(timeline)) {
+		/* Don't add tracker if timeline is full. */
+		tracker->point = MALI_TIMELINE_NO_POINT;
+		return;
+	}
+
+	tracker->timeline = timeline;
+	tracker->point    = timeline->point_next;
+
+	/* Find next available point. */
+	timeline->point_next++;
+	if (MALI_TIMELINE_NO_POINT == timeline->point_next) {
+		timeline->point_next++;
+	}
+
+	MALI_DEBUG_ASSERT(!mali_timeline_is_empty(timeline));
+
+	if (MALI_TIMELINE_TRACKER_GP == tracker->type) {
+		_mali_osk_atomic_inc(&gp_tracker_count);
+	} else if (MALI_TIMELINE_TRACKER_PP == tracker->type) {
+		if (mali_pp_job_is_virtual((struct mali_pp_job *)tracker->job)) {
+			_mali_osk_atomic_inc(&virt_pp_tracker_count);
+		} else {
+			_mali_osk_atomic_inc(&phy_pp_tracker_count);
+		}
+	}
+
+	/* Add tracker as new head on timeline's tracker list. */
+	if (NULL == timeline->tracker_head) {
+		/* Tracker list is empty. */
+		MALI_DEBUG_ASSERT(NULL == timeline->tracker_tail);
+
+		timeline->tracker_tail = tracker;
+
+		MALI_DEBUG_ASSERT(NULL == tracker->timeline_next);
+		MALI_DEBUG_ASSERT(NULL == tracker->timeline_prev);
+	} else {
+		MALI_DEBUG_ASSERT(NULL == timeline->tracker_head->timeline_next);
+
+		tracker->timeline_prev = timeline->tracker_head;
+		timeline->tracker_head->timeline_next = tracker;
+
+		MALI_DEBUG_ASSERT(NULL == tracker->timeline_next);
+	}
+	timeline->tracker_head = tracker;
+
+	MALI_DEBUG_ASSERT(NULL == timeline->tracker_head->timeline_next);
+	MALI_DEBUG_ASSERT(NULL == timeline->tracker_tail->timeline_prev);
+}
+
+/* Inserting the waiter object into the given timeline */
+static void mali_timeline_insert_waiter(struct mali_timeline *timeline, struct mali_timeline_waiter *waiter_new)
+{
+	struct mali_timeline_waiter *waiter_prev;
+	struct mali_timeline_waiter *waiter_next;
+
+	/* Waiter time must be between timeline head and tail, and there must
+	 * be less than MALI_TIMELINE_MAX_POINT_SPAN elements between */
+	MALI_DEBUG_ASSERT((waiter_new->point - timeline->point_oldest) < MALI_TIMELINE_MAX_POINT_SPAN);
+	MALI_DEBUG_ASSERT((-waiter_new->point + timeline->point_next) < MALI_TIMELINE_MAX_POINT_SPAN);
+
+	/* Finding out where to put this waiter, in the linked waiter list of the given timeline **/
+	waiter_prev = timeline->waiter_head; /* Insert new after  waiter_prev */
+	waiter_next = NULL;                  /* Insert new before waiter_next */
+
+	/* Iterating backwards from head (newest) to tail (oldest) until we
+	 * find the correct spot to insert the new waiter */
+	while (waiter_prev && mali_timeline_point_after(waiter_prev->point, waiter_new->point)) {
+		waiter_next = waiter_prev;
+		waiter_prev = waiter_prev->timeline_prev;
+	}
+
+	if (NULL == waiter_prev && NULL == waiter_next) {
+		/* list is empty */
+		timeline->waiter_head = waiter_new;
+		timeline->waiter_tail = waiter_new;
+	} else if (NULL == waiter_next) {
+		/* insert at head */
+		waiter_new->timeline_prev = timeline->waiter_head;
+		timeline->waiter_head->timeline_next = waiter_new;
+		timeline->waiter_head = waiter_new;
+	} else if (NULL == waiter_prev) {
+		/* insert at tail */
+		waiter_new->timeline_next = timeline->waiter_tail;
+		timeline->waiter_tail->timeline_prev = waiter_new;
+		timeline->waiter_tail = waiter_new;
+	} else {
+		/* insert between */
+		waiter_new->timeline_next = waiter_next;
+		waiter_new->timeline_prev = waiter_prev;
+		waiter_next->timeline_prev = waiter_new;
+		waiter_prev->timeline_next = waiter_new;
+	}
+}
+
+static void mali_timeline_update_delayed_work(struct mali_timeline *timeline)
+{
+	struct mali_timeline_system *system;
+	struct mali_timeline_tracker *oldest_tracker;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SOFT == timeline->id);
+
+	system = timeline->system;
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	/* Timer is disabled, early out. */
+	if (!system->timer_enabled) return;
+
+	oldest_tracker = timeline->tracker_tail;
+	if (NULL != oldest_tracker && 0 == oldest_tracker->trigger_ref_count) {
+		if (MALI_FALSE == oldest_tracker->timer_active) {
+			if (MALI_TRUE == timeline->timer_active) {
+				_mali_osk_wq_delayed_cancel_work_async(timeline->delayed_work);
+			}
+			_mali_osk_wq_delayed_schedule_work(timeline->delayed_work, MALI_TIMELINE_TIMEOUT_HZ);
+			oldest_tracker->timer_active = MALI_TRUE;
+			timeline->timer_active = MALI_TRUE;
+		}
+	} else if (MALI_TRUE == timeline->timer_active) {
+		_mali_osk_wq_delayed_cancel_work_async(timeline->delayed_work);
+		timeline->timer_active = MALI_FALSE;
+	}
+}
+
+static mali_scheduler_mask mali_timeline_update_oldest_point(struct mali_timeline *timeline)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	MALI_DEBUG_CODE({
+		struct mali_timeline_system *system = timeline->system;
+		MALI_DEBUG_ASSERT_POINTER(system);
+
+		MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+	});
+
+	if (NULL != timeline->tracker_tail) {
+		/* Set oldest point to oldest tracker's point */
+		timeline->point_oldest = timeline->tracker_tail->point;
+	} else {
+		/* No trackers, mark point list as empty */
+		timeline->point_oldest = timeline->point_next;
+	}
+
+	/* Release all waiters no longer on the timeline's point list.
+	 * Releasing a waiter can trigger this function to be called again, so
+	 * we do not store any pointers on stack. */
+	while (NULL != timeline->waiter_tail) {
+		u32 waiter_time_relative;
+		u32 time_head_relative;
+		struct mali_timeline_waiter *waiter = timeline->waiter_tail;
+
+		time_head_relative = timeline->point_next - timeline->point_oldest;
+		waiter_time_relative = waiter->point - timeline->point_oldest;
+
+		if (waiter_time_relative < time_head_relative) {
+			/* This and all following waiters are on the point list, so we are done. */
+			break;
+		}
+
+		/* Remove waiter from timeline's waiter list. */
+		if (NULL != waiter->timeline_next) {
+			waiter->timeline_next->timeline_prev = NULL;
+		} else {
+			/* This was the last waiter */
+			timeline->waiter_head = NULL;
+		}
+		timeline->waiter_tail = waiter->timeline_next;
+
+		/* Release waiter.  This could activate a tracker, if this was
+		 * the last waiter for the tracker. */
+		schedule_mask |= mali_timeline_system_release_waiter(timeline->system, waiter);
+	}
+
+	return schedule_mask;
+}
+
+static mali_scheduler_mask mali_timeline_release_with_depended_point(struct mali_timeline_tracker *tracker)
+{
+	struct mali_timeline *timeline;
+	struct mali_timeline_waiter *waiter;
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+	
+	timeline = tracker->timeline;
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SOFT == timeline->id);
+	
+	MALI_DEBUG_CODE({
+		struct mali_timeline_system *system = timeline->system;
+		MALI_DEBUG_ASSERT_POINTER(system);
+
+		MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+	});
+
+	/* Only release the waiter that wait for the tracker. */
+	waiter = timeline->waiter_tail;
+	while (NULL != waiter) {
+		if (waiter->point == tracker->point) {
+
+			struct mali_timeline_waiter *waiter_next;
+			struct mali_timeline_waiter *waiter_prev;
+			
+			waiter_next = waiter->timeline_next;
+			waiter_prev = waiter->timeline_prev;
+			waiter->timeline_next = NULL;
+			waiter->timeline_prev = NULL;
+
+			if (NULL != waiter_prev) {
+				waiter_prev->timeline_next = waiter_next;
+			}
+
+			if (NULL != waiter_next) {
+				waiter_next->timeline_prev = waiter_prev;
+			}
+
+			if (waiter ==  timeline->waiter_tail)
+				 timeline->waiter_tail = waiter_next;
+
+			if (waiter == timeline->waiter_head)
+				timeline->waiter_head = NULL;
+			
+			schedule_mask |= mali_timeline_system_release_waiter(timeline->system, waiter);
+			waiter = waiter_next;
+		}else {
+
+			waiter = waiter->timeline_next;
+		}
+	}
+
+	return schedule_mask;
+}
+
+void mali_timeline_tracker_init(struct mali_timeline_tracker *tracker,
+				mali_timeline_tracker_type type,
+				struct mali_timeline_fence *fence,
+				void *job)
+{
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_TRACKER_MAX > type);
+
+	/* Zero out all tracker members. */
+	_mali_osk_memset(tracker, 0, sizeof(*tracker));
+
+	tracker->type = type;
+	tracker->job = job;
+	tracker->trigger_ref_count = 1;  /* Prevents any callback from trigging while adding it */
+	tracker->os_tick_create = _mali_osk_time_tickcount();
+	MALI_DEBUG_CODE(tracker->magic = MALI_TIMELINE_TRACKER_MAGIC);
+
+	tracker->activation_error = MALI_TIMELINE_ACTIVATION_ERROR_NONE;
+
+	/* Copy fence. */
+	if (NULL != fence) {
+		_mali_osk_memcpy(&tracker->fence, fence, sizeof(struct mali_timeline_fence));
+	}
+}
+
+mali_scheduler_mask mali_timeline_tracker_release(struct mali_timeline_tracker *tracker)
+{
+	struct mali_timeline *timeline;
+	struct mali_timeline_system *system;
+	struct mali_timeline_tracker *tracker_next, *tracker_prev;
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+	u32 tid = _mali_osk_get_tid();
+
+	/* Upon entry a group lock will be held, but not a scheduler lock. */
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_TRACKER_MAGIC == tracker->magic);
+
+	/* Tracker should have been triggered */
+	MALI_DEBUG_ASSERT(0 == tracker->trigger_ref_count);
+
+	/* All waiters should have been released at this point */
+	MALI_DEBUG_ASSERT(NULL == tracker->waiter_head);
+	MALI_DEBUG_ASSERT(NULL == tracker->waiter_tail);
+
+	MALI_DEBUG_PRINT(3, ("Mali Timeline: releasing tracker for job 0x%08X\n", tracker->job));
+
+	timeline = tracker->timeline;
+	if (NULL == timeline) {
+		/* Tracker was not on a timeline, there is nothing to release. */
+		return MALI_SCHEDULER_MASK_EMPTY;
+	}
+
+	system = timeline->system;
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	/* Tracker should still be on timeline */
+	MALI_DEBUG_ASSERT(!mali_timeline_is_empty(timeline));
+	MALI_DEBUG_ASSERT(mali_timeline_is_point_on(timeline, tracker->point));
+
+	/* Tracker is no longer valid. */
+	MALI_DEBUG_CODE(tracker->magic = 0);
+
+	tracker_next = tracker->timeline_next;
+	tracker_prev = tracker->timeline_prev;
+	tracker->timeline_next = NULL;
+	tracker->timeline_prev = NULL;
+
+	/* Removing tracker from timeline's tracker list */
+	if (NULL == tracker_next) {
+		/* This tracker was the head */
+		timeline->tracker_head = tracker_prev;
+	} else {
+		tracker_next->timeline_prev = tracker_prev;
+	}
+
+	if (NULL == tracker_prev) {
+		/* This tracker was the tail */
+		timeline->tracker_tail = tracker_next;
+		MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+		/* Update the timeline's oldest time and release any waiters */
+		schedule_mask |= mali_timeline_update_oldest_point(timeline);
+		MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+	} else {
+		tracker_prev->timeline_next = tracker_next;
+		if (MALI_TIMELINE_SOFT == tracker->timeline->id) {
+			/* Use the signaled soft tracker to release the depended soft waiter */
+			schedule_mask |= mali_timeline_release_with_depended_point(tracker);
+			MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+		}
+	}
+
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	/* Update delayed work only when it is the soft job timeline */
+	if (MALI_TIMELINE_SOFT == tracker->timeline->id) {
+		mali_timeline_update_delayed_work(tracker->timeline);
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	return schedule_mask;
+}
+
+void mali_timeline_system_release_waiter_list(struct mali_timeline_system *system,
+		struct mali_timeline_waiter *tail,
+		struct mali_timeline_waiter *head)
+{
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(head);
+	MALI_DEBUG_ASSERT_POINTER(tail);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	head->tracker_next = system->waiter_empty_list;
+	system->waiter_empty_list = tail;
+}
+
+static mali_scheduler_mask mali_timeline_tracker_activate(struct mali_timeline_tracker *tracker)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+	struct mali_timeline_system *system;
+	struct mali_timeline *timeline;
+	u32 tid = _mali_osk_get_tid();
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_TRACKER_MAGIC == tracker->magic);
+
+	system = tracker->system;
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	tracker->os_tick_activate = _mali_osk_time_tickcount();
+
+	if (NULL != tracker->waiter_head) {
+		mali_timeline_system_release_waiter_list(system, tracker->waiter_tail, tracker->waiter_head);
+		tracker->waiter_head = NULL;
+		tracker->waiter_tail = NULL;
+	}
+
+	switch (tracker->type) {
+	case MALI_TIMELINE_TRACKER_GP:
+		schedule_mask = mali_scheduler_activate_gp_job((struct mali_gp_job *) tracker->job);
+
+		_mali_osk_atomic_dec(&gp_tracker_count);
+		break;
+	case MALI_TIMELINE_TRACKER_PP:
+		if (mali_pp_job_is_virtual((struct mali_pp_job *)tracker->job)) {
+			_mali_osk_atomic_dec(&virt_pp_tracker_count);
+		} else {
+			_mali_osk_atomic_dec(&phy_pp_tracker_count);
+		}
+		schedule_mask = mali_scheduler_activate_pp_job((struct mali_pp_job *) tracker->job);
+		break;
+	case MALI_TIMELINE_TRACKER_SOFT:
+		timeline = tracker->timeline;
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		schedule_mask |= mali_soft_job_system_activate_job((struct mali_soft_job *) tracker->job);
+
+		/* Start a soft timer to make sure the soft job be released in a limited time */
+		mali_spinlock_reentrant_wait(system->spinlock, tid);
+		mali_timeline_update_delayed_work(timeline);
+		mali_spinlock_reentrant_signal(system->spinlock, tid);
+		break;
+	case MALI_TIMELINE_TRACKER_WAIT:
+		mali_timeline_fence_wait_activate((struct mali_timeline_fence_wait_tracker *) tracker->job);
+		break;
+	case MALI_TIMELINE_TRACKER_SYNC:
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+		mali_timeline_sync_fence_activate((struct mali_timeline_sync_fence_tracker *) tracker->job);
+#else
+		MALI_PRINT_ERROR(("Mali Timeline: sync tracker not supported\n", tracker->type));
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+		break;
+	default:
+		MALI_PRINT_ERROR(("Mali Timeline - Illegal tracker type: %d\n", tracker->type));
+		break;
+	}
+
+	return schedule_mask;
+}
+
+void mali_timeline_system_tracker_get(struct mali_timeline_system *system, struct mali_timeline_tracker *tracker)
+{
+	u32 tid = _mali_osk_get_tid();
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	MALI_DEBUG_ASSERT(0 < tracker->trigger_ref_count);
+	tracker->trigger_ref_count++;
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+}
+
+mali_scheduler_mask mali_timeline_system_tracker_put(struct mali_timeline_system *system, struct mali_timeline_tracker *tracker, mali_timeline_activation_error activation_error)
+{
+	u32 tid = _mali_osk_get_tid();
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	MALI_DEBUG_ASSERT(0 < tracker->trigger_ref_count);
+	tracker->trigger_ref_count--;
+
+	tracker->activation_error |= activation_error;
+
+	if (0 == tracker->trigger_ref_count) {
+		schedule_mask |= mali_timeline_tracker_activate(tracker);
+		tracker = NULL;
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	return schedule_mask;
+}
+
+void mali_timeline_fence_copy_uk_fence(struct mali_timeline_fence *fence, _mali_uk_fence_t *uk_fence)
+{
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+	MALI_DEBUG_ASSERT_POINTER(uk_fence);
+
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		fence->points[i] = uk_fence->points[i];
+	}
+
+	fence->sync_fd = uk_fence->sync_fd;
+}
+
+struct mali_timeline_system *mali_timeline_system_create(struct mali_session_data *session)
+{
+	u32 i;
+	struct mali_timeline_system *system;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_PRINT(4, ("Mali Timeline: creating timeline system\n"));
+
+	system = (struct mali_timeline_system *) _mali_osk_calloc(1, sizeof(struct mali_timeline_system));
+	if (NULL == system) {
+		return NULL;
+	}
+
+	system->spinlock = mali_spinlock_reentrant_init(_MALI_OSK_LOCK_ORDER_TIMELINE_SYSTEM);
+	if (NULL == system->spinlock) {
+		mali_timeline_system_destroy(system);
+		return NULL;
+	}
+
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		system->timelines[i] = mali_timeline_create(system, (enum mali_timeline_id)i);
+		if (NULL == system->timelines[i]) {
+			mali_timeline_system_destroy(system);
+			return NULL;
+		}
+	}
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	system->signaled_sync_tl = mali_sync_timeline_create(NULL, "mali-always-signaled");
+	if (NULL == system->signaled_sync_tl) {
+		mali_timeline_system_destroy(system);
+		return NULL;
+	}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	system->waiter_empty_list = NULL;
+	system->session = session;
+	system->timer_enabled = MALI_TRUE;
+
+	system->wait_queue = _mali_osk_wait_queue_init();
+	if (NULL == system->wait_queue) {
+		mali_timeline_system_destroy(system);
+		return NULL;
+	}
+
+	return system;
+}
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE) ||defined(CONFIG_SYNC) ||defined(CONFIG_SYNC_FILE)
+/**
+ * Check if there are any trackers left on timeline.
+ *
+ * Used as a wait queue conditional.
+ *
+ * @param data Timeline.
+ * @return MALI_TRUE if there are no trackers on timeline, MALI_FALSE if not.
+ */
+static mali_bool mali_timeline_has_no_trackers(void *data)
+{
+	struct mali_timeline *timeline = (struct mali_timeline *) data;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	return mali_timeline_is_empty(timeline);
+}
+#if defined(CONFIG_SYNC) ||defined(CONFIG_SYNC_FILE)
+/**
+ * Cancel sync fence waiters waited upon by trackers on all timelines.
+ *
+ * Will return after all timelines have no trackers left.
+ *
+ * @param system Timeline system.
+ */
+static void mali_timeline_cancel_sync_fence_waiters(struct mali_timeline_system *system)
+{
+	u32 i;
+	u32 tid = _mali_osk_get_tid();
+	struct mali_timeline_tracker *tracker, *tracker_next;
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(tracker_list);
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+	MALI_DEBUG_ASSERT(system->session->is_aborting);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	/* Cancel sync fence waiters. */
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline = system->timelines[i];
+
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		tracker_next = timeline->tracker_tail;
+		while (NULL != tracker_next) {
+			tracker = tracker_next;
+			tracker_next = tracker->timeline_next;
+
+			if (NULL == tracker->sync_fence) continue;
+
+			MALI_DEBUG_PRINT(3, ("Mali Timeline: Cancelling sync fence wait for tracker 0x%08X.\n", tracker));
+
+			/* Cancel sync fence waiter. */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+			if (0 == sync_fence_cancel_async(tracker->sync_fence, &tracker->sync_fence_waiter)) {
+#else
+			if (0 == mali_internal_sync_fence_cancel_async(tracker->sync_fence, &tracker->sync_fence_waiter)) {
+#endif
+				/* Callback was not called, move tracker to local list. */
+				_mali_osk_list_add(&tracker->sync_fence_cancel_list, &tracker_list);
+			}
+		}
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	/* Manually call sync fence callback in order to release waiter and trigger activation of tracker. */
+	_MALI_OSK_LIST_FOREACHENTRY(tracker, tracker_next, &tracker_list, struct mali_timeline_tracker, sync_fence_cancel_list) {
+		mali_timeline_sync_fence_callback(tracker->sync_fence, &tracker->sync_fence_waiter);
+	}
+
+	/* Sleep until all sync fence callbacks are done and all timelines are empty. */
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline = system->timelines[i];
+
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		_mali_osk_wait_queue_wait_event(system->wait_queue, mali_timeline_has_no_trackers, (void *) timeline);
+	}
+}
+
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+static void mali_timeline_cancel_dma_fence_waiters(struct mali_timeline_system *system)
+{
+	u32 i, j;
+	u32 tid = _mali_osk_get_tid();
+	struct mali_pp_job *pp_job = NULL;
+	struct mali_pp_job *next_pp_job = NULL;
+	struct mali_timeline *timeline = NULL;
+	struct mali_timeline_tracker *tracker, *tracker_next;
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(pp_job_list);
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+	MALI_DEBUG_ASSERT(system->session->is_aborting);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	/* Cancel dma fence waiters. */
+	timeline = system->timelines[MALI_TIMELINE_PP];
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	tracker_next = timeline->tracker_tail;
+	while (NULL != tracker_next) {
+		mali_bool fence_is_signaled = MALI_TRUE;
+		tracker = tracker_next;
+		tracker_next = tracker->timeline_next;
+
+		if (NULL == tracker->waiter_dma_fence) continue;
+		pp_job = (struct mali_pp_job *)tracker->job;
+		MALI_DEBUG_ASSERT_POINTER(pp_job);
+		MALI_DEBUG_PRINT(3, ("Mali Timeline: Cancelling dma fence waiter for tracker 0x%08X.\n", tracker));
+
+		for (j = 0; j < pp_job->dma_fence_context.num_dma_fence_waiter; j++) {
+			if (pp_job->dma_fence_context.mali_dma_fence_waiters[j]) {
+				/* Cancel a previously callback from the fence.
+				* This function returns true if the callback is successfully removed,
+				* or false if the fence has already been signaled.
+				*/
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+				bool ret = dma_fence_remove_callback(pp_job->dma_fence_context.mali_dma_fence_waiters[j]->fence,
+								     &pp_job->dma_fence_context.mali_dma_fence_waiters[j]->base);
+
+#else
+				bool ret = fence_remove_callback(pp_job->dma_fence_context.mali_dma_fence_waiters[j]->fence,
+								 &pp_job->dma_fence_context.mali_dma_fence_waiters[j]->base);
+#endif
+				if (ret) {
+					fence_is_signaled = MALI_FALSE;
+				}
+			}
+		}
+
+		/* Callbacks were not called, move pp job to local list. */
+		if (MALI_FALSE == fence_is_signaled)
+			_mali_osk_list_add(&pp_job->list, &pp_job_list);
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	/* Manually call dma fence callback in order to release waiter and trigger activation of tracker. */
+	_MALI_OSK_LIST_FOREACHENTRY(pp_job, next_pp_job, &pp_job_list, struct mali_pp_job, list) {
+		mali_timeline_dma_fence_callback((void *)pp_job);
+	}
+
+	/* Sleep until all dma fence callbacks are done and all timelines are empty. */
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline = system->timelines[i];
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+		_mali_osk_wait_queue_wait_event(system->wait_queue, mali_timeline_has_no_trackers, (void *) timeline);
+	}
+}
+#endif
+#endif
+void mali_timeline_system_abort(struct mali_timeline_system *system)
+{
+	MALI_DEBUG_CODE(u32 tid = _mali_osk_get_tid(););
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+	MALI_DEBUG_ASSERT(system->session->is_aborting);
+
+	MALI_DEBUG_PRINT(3, ("Mali Timeline: Aborting timeline system for session 0x%08X.\n", system->session));
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	mali_timeline_cancel_sync_fence_waiters(system);
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	mali_timeline_cancel_dma_fence_waiters(system);
+#endif
+
+	/* Should not be any waiters or trackers left at this point. */
+	MALI_DEBUG_CODE({
+		u32 i;
+		mali_spinlock_reentrant_wait(system->spinlock, tid);
+		for (i = 0; i < MALI_TIMELINE_MAX; ++i)
+		{
+			struct mali_timeline *timeline = system->timelines[i];
+			MALI_DEBUG_ASSERT_POINTER(timeline);
+			MALI_DEBUG_ASSERT(timeline->point_oldest == timeline->point_next);
+			MALI_DEBUG_ASSERT(NULL == timeline->tracker_head);
+			MALI_DEBUG_ASSERT(NULL == timeline->tracker_tail);
+			MALI_DEBUG_ASSERT(NULL == timeline->waiter_head);
+			MALI_DEBUG_ASSERT(NULL == timeline->waiter_tail);
+		}
+		mali_spinlock_reentrant_signal(system->spinlock, tid);
+	});
+}
+
+void mali_timeline_system_destroy(struct mali_timeline_system *system)
+{
+	u32 i;
+	struct mali_timeline_waiter *waiter, *next;
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	u32 tid = _mali_osk_get_tid();
+#endif
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+
+	MALI_DEBUG_PRINT(4, ("Mali Timeline: destroying timeline system\n"));
+
+	if (NULL != system) {
+
+		/* There should be no waiters left on this queue. */
+		if (NULL != system->wait_queue) {
+			_mali_osk_wait_queue_term(system->wait_queue);
+			system->wait_queue = NULL;
+		}
+
+		/* Free all waiters in empty list */
+		waiter = system->waiter_empty_list;
+		while (NULL != waiter) {
+			next = waiter->tracker_next;
+			_mali_osk_free(waiter);
+			waiter = next;
+		}
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+		if (NULL != system->signaled_sync_tl) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+			sync_timeline_destroy(system->signaled_sync_tl);
+#else
+			mali_internal_sync_timeline_destroy(system->signaled_sync_tl);
+#endif
+		}
+
+		for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+			if ((NULL != system->timelines[i]) && (NULL != system->timelines[i]->spinlock)) {
+				mali_spinlock_reentrant_wait(system->timelines[i]->spinlock, tid);
+				system->timelines[i]->destroyed = MALI_TRUE;
+				mali_spinlock_reentrant_signal(system->timelines[i]->spinlock, tid);
+			}
+		}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+		for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+			if (NULL != system->timelines[i]) {
+				mali_timeline_destroy(system->timelines[i]);
+			}
+		}
+
+		if (NULL != system->spinlock) {
+			mali_spinlock_reentrant_term(system->spinlock);
+		}
+
+		_mali_osk_free(system);
+	}
+}
+
+/**
+ * Find how many waiters are needed for a given fence.
+ *
+ * @param fence The fence to check.
+ * @return Number of waiters needed for fence.
+ */
+static u32 mali_timeline_fence_num_waiters(struct mali_timeline_fence *fence)
+{
+	u32 i, num_waiters = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		if (MALI_TIMELINE_NO_POINT != fence->points[i]) {
+			++num_waiters;
+		}
+	}
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (-1 != fence->sync_fd) ++num_waiters;
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	return num_waiters;
+}
+
+static struct mali_timeline_waiter *mali_timeline_system_get_zeroed_waiter(struct mali_timeline_system *system)
+{
+	struct mali_timeline_waiter *waiter;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	waiter = system->waiter_empty_list;
+	if (NULL != waiter) {
+		/* Remove waiter from empty list and zero it */
+		system->waiter_empty_list = waiter->tracker_next;
+		_mali_osk_memset(waiter, 0, sizeof(*waiter));
+	}
+
+	/* Return NULL if list was empty. */
+	return waiter;
+}
+
+static void mali_timeline_system_allocate_waiters(struct mali_timeline_system *system,
+		struct mali_timeline_waiter **tail,
+		struct mali_timeline_waiter **head,
+		int max_num_waiters)
+{
+	u32 i, tid = _mali_osk_get_tid();
+	mali_bool do_alloc;
+	struct mali_timeline_waiter *waiter;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(tail);
+	MALI_DEBUG_ASSERT_POINTER(head);
+
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	*head = *tail = NULL;
+	do_alloc = MALI_FALSE;
+	i = 0;
+	while (i < max_num_waiters) {
+		if (MALI_FALSE == do_alloc) {
+			waiter = mali_timeline_system_get_zeroed_waiter(system);
+			if (NULL == waiter) {
+				do_alloc = MALI_TRUE;
+				mali_spinlock_reentrant_signal(system->spinlock, tid);
+				continue;
+			}
+		} else {
+			waiter = _mali_osk_calloc(1, sizeof(struct mali_timeline_waiter));
+			if (NULL == waiter) break;
+		}
+		++i;
+		if (NULL == *tail) {
+			*tail = waiter;
+			*head = waiter;
+		} else {
+			(*head)->tracker_next = waiter;
+			*head = waiter;
+		}
+	}
+	if (MALI_TRUE == do_alloc) {
+		mali_spinlock_reentrant_wait(system->spinlock, tid);
+	}
+}
+
+/**
+ * Create waiters for the given tracker. The tracker is activated when all waiters are release.
+ *
+ * @note Tracker can potentially be activated before this function returns.
+ *
+ * @param system Timeline system.
+ * @param tracker Tracker we will create waiters for.
+ * @param waiter_tail List of pre-allocated waiters.
+ * @param waiter_head List of pre-allocated waiters.
+ */
+static void mali_timeline_system_create_waiters_and_unlock(struct mali_timeline_system *system,
+		struct mali_timeline_tracker *tracker,
+		struct mali_timeline_waiter *waiter_tail,
+		struct mali_timeline_waiter *waiter_head)
+{
+	int i;
+	u32 tid = _mali_osk_get_tid();
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_fence *sync_fence = NULL;
+#else
+	struct mali_internal_sync_fence *sync_fence = NULL;
+#endif
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	MALI_DEBUG_ASSERT(NULL == tracker->waiter_head);
+	MALI_DEBUG_ASSERT(NULL == tracker->waiter_tail);
+	MALI_DEBUG_ASSERT(NULL != tracker->job);
+
+	/* Creating waiter object for all the timelines the fence is put on. Inserting this waiter
+	 * into the timelines sorted list of waiters */
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		mali_timeline_point point;
+		struct mali_timeline *timeline;
+		struct mali_timeline_waiter *waiter;
+
+		/* Get point on current timeline from tracker's fence. */
+		point = tracker->fence.points[i];
+
+		if (likely(MALI_TIMELINE_NO_POINT == point)) {
+			/* Fence contains no point on this timeline so we don't need a waiter. */
+			continue;
+		}
+
+		timeline = system->timelines[i];
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		if (unlikely(!mali_timeline_is_point_valid(timeline, point))) {
+			MALI_PRINT_ERROR(("Mali Timeline: point %d is not valid (oldest=%d, next=%d)\n",
+					  point, timeline->point_oldest, timeline->point_next));
+			continue;
+		}
+
+		if (likely(mali_timeline_is_point_released(timeline, point))) {
+			/* Tracker representing the point has been released so we don't need a
+			 * waiter. */
+			continue;
+		}
+
+		if ((MALI_TIMELINE_SOFT == timeline->id) && mali_timeline_is_tracker_released(timeline, point)) {
+			/* The tracker that the point related to has already been released, so no need to a waiter. */
+			continue;
+		}
+		
+
+		/* The point is on timeline. */
+		MALI_DEBUG_ASSERT(mali_timeline_is_point_on(timeline, point));
+
+		/* Get a new zeroed waiter object. */
+		if (likely(NULL != waiter_tail)) {
+			waiter = waiter_tail;
+			waiter_tail = waiter_tail->tracker_next;
+		} else {
+			MALI_PRINT_ERROR(("Mali Timeline: failed to allocate memory for waiter\n"));
+			continue;
+		}
+
+		/* Yanking the trigger ref count of the tracker. */
+		tracker->trigger_ref_count++;
+
+		waiter->point   = point;
+		waiter->tracker = tracker;
+
+		/* Insert waiter on tracker's singly-linked waiter list. */
+		if (NULL == tracker->waiter_head) {
+			/* list is empty */
+			MALI_DEBUG_ASSERT(NULL == tracker->waiter_tail);
+			tracker->waiter_tail = waiter;
+		} else {
+			tracker->waiter_head->tracker_next = waiter;
+		}
+		tracker->waiter_head = waiter;
+
+		/* Add waiter to timeline. */
+		mali_timeline_insert_waiter(timeline, waiter);
+	}
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (-1 != tracker->fence.sync_fd) {
+		int ret;
+		struct mali_timeline_waiter *waiter;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence = sync_fence_fdget(tracker->fence.sync_fd);
+#else
+		sync_fence = mali_internal_sync_fence_fdget(tracker->fence.sync_fd);
+#endif
+		if (unlikely(NULL == sync_fence)) {
+			MALI_PRINT_ERROR(("Mali Timeline: failed to get sync fence from fd %d\n", tracker->fence.sync_fd));
+			goto exit;
+		}
+
+		/* Check if we have a zeroed waiter object available. */
+		if (unlikely(NULL == waiter_tail)) {
+			MALI_PRINT_ERROR(("Mali Timeline: failed to allocate memory for waiter\n"));
+			goto exit;
+		}
+
+		/* Start asynchronous wait that will release waiter when the fence is signaled. */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence_waiter_init(&tracker->sync_fence_waiter, mali_timeline_sync_fence_callback);
+		ret = sync_fence_wait_async(sync_fence, &tracker->sync_fence_waiter);
+#else
+		mali_internal_sync_fence_waiter_init(&tracker->sync_fence_waiter, mali_timeline_sync_fence_callback);
+		ret = mali_internal_sync_fence_wait_async(sync_fence, &tracker->sync_fence_waiter);
+#endif
+		if (1 == ret) {
+			/* Fence already signaled, no waiter needed. */
+			tracker->fence.sync_fd = -1;
+			goto exit;
+		} else if (0 != ret) {
+			MALI_PRINT_ERROR(("Mali Timeline: sync fence fd %d signaled with error %d\n", tracker->fence.sync_fd, ret));
+			tracker->activation_error |= MALI_TIMELINE_ACTIVATION_ERROR_SYNC_BIT;
+			goto exit;
+		}
+
+		/* Grab new zeroed waiter object. */
+		waiter = waiter_tail;
+		waiter_tail = waiter_tail->tracker_next;
+
+		/* Increase the trigger ref count of the tracker. */
+		tracker->trigger_ref_count++;
+
+		waiter->point   = MALI_TIMELINE_NO_POINT;
+		waiter->tracker = tracker;
+
+		/* Insert waiter on tracker's singly-linked waiter list. */
+		if (NULL == tracker->waiter_head) {
+			/* list is empty */
+			MALI_DEBUG_ASSERT(NULL == tracker->waiter_tail);
+			tracker->waiter_tail = waiter;
+		} else {
+			tracker->waiter_head->tracker_next = waiter;
+		}
+		tracker->waiter_head = waiter;
+
+		/* Also store waiter in separate field for easy access by sync callback. */
+		tracker->waiter_sync = waiter;
+
+		/* Store the sync fence in tracker so we can retrieve in abort session, if needed. */
+		tracker->sync_fence = sync_fence;
+
+		sync_fence = NULL;
+	}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)*/
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	if ((NULL != tracker->timeline) && (MALI_TIMELINE_PP == tracker->timeline->id)) {
+
+		struct mali_pp_job *job = (struct mali_pp_job *)tracker->job;
+
+		if (0 < job->dma_fence_context.num_dma_fence_waiter) {
+			struct mali_timeline_waiter *waiter;
+			/* Check if we have a zeroed waiter object available. */
+			if (unlikely(NULL == waiter_tail)) {
+				MALI_PRINT_ERROR(("Mali Timeline: failed to allocate memory for waiter\n"));
+				goto exit;
+			}
+
+			/* Grab new zeroed waiter object. */
+			waiter = waiter_tail;
+			waiter_tail = waiter_tail->tracker_next;
+
+			/* Increase the trigger ref count of the tracker. */
+			tracker->trigger_ref_count++;
+
+			waiter->point   = MALI_TIMELINE_NO_POINT;
+			waiter->tracker = tracker;
+
+			/* Insert waiter on tracker's singly-linked waiter list. */
+			if (NULL == tracker->waiter_head) {
+				/* list is empty */
+				MALI_DEBUG_ASSERT(NULL == tracker->waiter_tail);
+				tracker->waiter_tail = waiter;
+			} else {
+				tracker->waiter_head->tracker_next = waiter;
+			}
+			tracker->waiter_head = waiter;
+
+			/* Also store waiter in separate field for easy access by sync callback. */
+			tracker->waiter_dma_fence = waiter;
+		}
+	}
+#endif /* defined(CONFIG_MALI_DMA_BUF_FENCE)*/
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE) ||defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+exit:
+#endif /* defined(CONFIG_MALI_DMA_BUF_FENCE) || defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	if (NULL != waiter_tail) {
+		mali_timeline_system_release_waiter_list(system, waiter_tail, waiter_head);
+	}
+
+	/* Release the initial trigger ref count. */
+	tracker->trigger_ref_count--;
+
+	/* If there were no waiters added to this tracker we activate immediately. */
+	if (0 == tracker->trigger_ref_count) {
+		schedule_mask |= mali_timeline_tracker_activate(tracker);
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (NULL != sync_fence) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence_put(sync_fence);
+#else
+		fput(sync_fence->file);
+#endif
+	}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	mali_executor_schedule_from_mask(schedule_mask, MALI_FALSE);
+}
+
+mali_timeline_point mali_timeline_system_add_tracker(struct mali_timeline_system *system,
+		struct mali_timeline_tracker *tracker,
+		enum mali_timeline_id timeline_id)
+{
+	int num_waiters = 0;
+	struct mali_timeline_waiter *waiter_tail, *waiter_head;
+	u32 tid = _mali_osk_get_tid();
+
+	mali_timeline_point point = MALI_TIMELINE_NO_POINT;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	MALI_DEBUG_ASSERT(MALI_FALSE == system->session->is_aborting);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_TRACKER_MAX > tracker->type);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_TRACKER_MAGIC == tracker->magic);
+
+	MALI_DEBUG_PRINT(4, ("Mali Timeline: adding tracker for job %p, timeline: %d\n", tracker->job, timeline_id));
+
+	MALI_DEBUG_ASSERT(0 < tracker->trigger_ref_count);
+	tracker->system = system;
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	num_waiters = mali_timeline_fence_num_waiters(&tracker->fence);
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	if (MALI_TIMELINE_PP == timeline_id) {
+		struct mali_pp_job *job = (struct mali_pp_job *)tracker->job;
+		if (0 < job->dma_fence_context.num_dma_fence_waiter)
+			num_waiters++;
+	}
+#endif
+
+	/* Allocate waiters. */
+	mali_timeline_system_allocate_waiters(system, &waiter_tail, &waiter_head, num_waiters);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	/* Add tracker to timeline.  This will allocate a point for the tracker on the timeline. If
+	 * timeline ID is MALI_TIMELINE_NONE the tracker will NOT be added to a timeline and the
+	 * point will be MALI_TIMELINE_NO_POINT.
+	 *
+	 * NOTE: the tracker can fail to be added if the timeline is full.  If this happens, the
+	 * point will be MALI_TIMELINE_NO_POINT. */
+	MALI_DEBUG_ASSERT(timeline_id < MALI_TIMELINE_MAX || timeline_id == MALI_TIMELINE_NONE);
+	if (likely(timeline_id < MALI_TIMELINE_MAX)) {
+		struct mali_timeline *timeline = system->timelines[timeline_id];
+		mali_timeline_insert_tracker(timeline, tracker);
+		MALI_DEBUG_ASSERT(!mali_timeline_is_empty(timeline));
+	}
+
+	point = tracker->point;
+
+	/* Create waiters for tracker based on supplied fence.  Each waiter will increase the
+	 * trigger ref count. */
+	mali_timeline_system_create_waiters_and_unlock(system, tracker, waiter_tail, waiter_head);
+	tracker = NULL;
+
+	/* At this point the tracker object might have been freed so we should no longer
+	 * access it. */
+
+
+	/* The tracker will always be activated after calling add_tracker, even if NO_POINT is
+	 * returned. */
+	return point;
+}
+
+static mali_scheduler_mask mali_timeline_system_release_waiter(struct mali_timeline_system *system,
+		struct mali_timeline_waiter *waiter)
+{
+	struct mali_timeline_tracker *tracker;
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(waiter);
+
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_SYSTEM_LOCKED(system));
+
+	tracker = waiter->tracker;
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	/* At this point the waiter has been removed from the timeline's waiter list, but it is
+	 * still on the tracker's waiter list.  All of the tracker's waiters will be released when
+	 * the tracker is activated. */
+
+	waiter->point   = MALI_TIMELINE_NO_POINT;
+	waiter->tracker = NULL;
+
+	tracker->trigger_ref_count--;
+	if (0 == tracker->trigger_ref_count) {
+		/* This was the last waiter; activate tracker */
+		schedule_mask |= mali_timeline_tracker_activate(tracker);
+		tracker = NULL;
+	}
+
+	return schedule_mask;
+}
+
+mali_timeline_point mali_timeline_system_get_latest_point(struct mali_timeline_system *system,
+		enum mali_timeline_id timeline_id)
+{
+	mali_timeline_point point;
+	struct mali_timeline *timeline;
+	u32 tid = _mali_osk_get_tid();
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	if (MALI_TIMELINE_MAX <= timeline_id) {
+		return MALI_TIMELINE_NO_POINT;
+	}
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	timeline = system->timelines[timeline_id];
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	point = MALI_TIMELINE_NO_POINT;
+	if (timeline->point_oldest != timeline->point_next) {
+		point = timeline->point_next - 1;
+		if (MALI_TIMELINE_NO_POINT == point) point--;
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	return point;
+}
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+static void mali_timeline_do_sync_fence_callback(void *arg)
+{
+	_MALI_OSK_LIST_HEAD_STATIC_INIT(list);
+	struct mali_timeline_tracker *tracker;
+	struct mali_timeline_tracker *tmp_tracker;
+	u32 tid = _mali_osk_get_tid();
+
+	MALI_IGNORE(arg);
+
+	/*
+	 * Quickly "unhook" the jobs pending to be deleted, so we can release
+	 * the lock before we start deleting the job objects
+	 * (without any locks held)
+	 */
+	_mali_osk_spinlock_irq_lock(sync_fence_callback_list_lock);
+	_mali_osk_list_move_list(&sync_fence_callback_queue, &list);
+	_mali_osk_spinlock_irq_unlock(sync_fence_callback_list_lock);
+
+	_MALI_OSK_LIST_FOREACHENTRY(tracker, tmp_tracker, &list,
+				    struct mali_timeline_tracker, sync_fence_signal_list) {
+		mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+		mali_bool is_aborting = MALI_FALSE;
+		int fence_status = 0;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		struct sync_fence *sync_fence = NULL;
+#else
+		struct mali_internal_sync_fence *sync_fence = NULL;
+#endif
+		struct mali_timeline_system  *system = NULL;
+		struct mali_timeline_waiter  *waiter = NULL;
+
+		_mali_osk_list_delinit(&tracker->sync_fence_signal_list);
+
+		sync_fence = tracker->sync_fence;
+		MALI_DEBUG_ASSERT_POINTER(sync_fence);
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 17, 0)
+		fence_status = sync_fence->status;
+#elif LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+		fence_status = atomic_read(&sync_fence->status);
+#else
+		fence_status = sync_fence->fence->ops->signaled(sync_fence->fence);
+#endif
+
+		system = tracker->system;
+		MALI_DEBUG_ASSERT_POINTER(system);
+		MALI_DEBUG_ASSERT_POINTER(system->session);
+
+		mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+		is_aborting = system->session->is_aborting;
+		if (!is_aborting && (0 > fence_status)) {
+			MALI_PRINT_ERROR(("Mali Timeline: sync fence fd %d signaled with error %d\n", tracker->fence.sync_fd, fence_status));
+			tracker->activation_error |= MALI_TIMELINE_ACTIVATION_ERROR_SYNC_BIT;
+		}
+
+		waiter = tracker->waiter_sync;
+		MALI_DEBUG_ASSERT_POINTER(waiter);
+
+		tracker->sync_fence = NULL;
+		tracker->fence.sync_fd = -1;
+
+		schedule_mask |= mali_timeline_system_release_waiter(system, waiter);
+
+		/* If aborting, wake up sleepers that are waiting for sync fence callbacks to complete. */
+		if (is_aborting) {
+			_mali_osk_wait_queue_wake_up(system->wait_queue);
+		}
+
+		mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+		/*
+		 * Older versions of Linux, before 3.5, doesn't support fput() in interrupt
+		 * context. For those older kernels, allocate a list object and put the
+		 * fence object on that and defer the call to sync_fence_put() to a workqueue.
+		 */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3,5,0)
+		{
+			struct mali_deferred_fence_put_entry *obj;
+
+			obj = kzalloc(sizeof(struct mali_deferred_fence_put_entry), GFP_ATOMIC);
+			if (obj) {
+				unsigned long flags;
+				mali_bool schedule = MALI_FALSE;
+
+				obj->fence = sync_fence;
+
+				spin_lock_irqsave(&mali_timeline_sync_fence_to_free_lock, flags);
+				if (hlist_empty(&mali_timeline_sync_fence_to_free_list))
+					schedule = MALI_TRUE;
+				hlist_add_head(&obj->list, &mali_timeline_sync_fence_to_free_list);
+				spin_unlock_irqrestore(&mali_timeline_sync_fence_to_free_lock, flags);
+
+				if (schedule)
+					schedule_delayed_work(&delayed_sync_fence_put, 0);
+			}
+		}
+#else
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence_put(sync_fence);
+#else
+		fput(sync_fence->file);
+#endif
+#endif /* LINUX_VERSION_CODE < KERNEL_VERSION(3,5,0) */
+
+		if (!is_aborting) {
+			mali_executor_schedule_from_mask(schedule_mask, MALI_TRUE);
+		}
+	}
+}
+#endif
+_mali_osk_errcode_t mali_timeline_initialize(void)
+{
+	_mali_osk_atomic_init(&gp_tracker_count, 0);
+	_mali_osk_atomic_init(&phy_pp_tracker_count, 0);
+	_mali_osk_atomic_init(&virt_pp_tracker_count, 0);
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	sync_fence_callback_list_lock = _mali_osk_spinlock_irq_init(_MALI_OSK_LOCKFLAG_UNORDERED, _MALI_OSK_LOCK_ORDER_FIRST);
+	if (NULL == sync_fence_callback_list_lock) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	sync_fence_callback_work_t = _mali_osk_wq_create_work(
+					     mali_timeline_do_sync_fence_callback, NULL);
+
+	if (NULL == sync_fence_callback_work_t) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif
+	return _MALI_OSK_ERR_OK;
+}
+
+
+void mali_timeline_terminate(void)
+{
+	_mali_osk_atomic_term(&gp_tracker_count);
+	_mali_osk_atomic_term(&phy_pp_tracker_count);
+	_mali_osk_atomic_term(&virt_pp_tracker_count);
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (NULL != sync_fence_callback_list_lock) {
+		_mali_osk_spinlock_irq_term(sync_fence_callback_list_lock);
+		sync_fence_callback_list_lock = NULL;
+	}
+
+	if (NULL != sync_fence_callback_work_t) {
+		_mali_osk_wq_delete_work(sync_fence_callback_work_t);
+		sync_fence_callback_work_t = NULL;
+	}
+#endif
+}
+
+#if defined(MALI_TIMELINE_DEBUG_FUNCTIONS)
+
+static mali_bool is_waiting_on_timeline(struct mali_timeline_tracker *tracker, enum mali_timeline_id id)
+{
+	struct mali_timeline *timeline;
+	struct mali_timeline_system *system;
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	MALI_DEBUG_ASSERT_POINTER(tracker->timeline);
+	timeline = tracker->timeline;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline->system);
+	system = timeline->system;
+
+	if (MALI_TIMELINE_MAX > id) {
+		if (MALI_TIMELINE_NO_POINT != tracker->fence.points[id]) {
+			return mali_timeline_is_point_on(system->timelines[id], tracker->fence.points[id]);
+		} else {
+			return MALI_FALSE;
+		}
+	} else {
+		MALI_DEBUG_ASSERT(MALI_TIMELINE_NONE == id);
+		return MALI_FALSE;
+	}
+}
+
+static const char *timeline_id_to_string(enum mali_timeline_id id)
+{
+	switch (id) {
+	case MALI_TIMELINE_GP:
+		return "GP";
+	case MALI_TIMELINE_PP:
+		return "PP";
+	case MALI_TIMELINE_SOFT:
+		return "SOFT";
+	default:
+		return "NONE";
+	}
+}
+
+static const char *timeline_tracker_type_to_string(enum mali_timeline_tracker_type type)
+{
+	switch (type) {
+	case MALI_TIMELINE_TRACKER_GP:
+		return "GP";
+	case MALI_TIMELINE_TRACKER_PP:
+		return "PP";
+	case MALI_TIMELINE_TRACKER_SOFT:
+		return "SOFT";
+	case MALI_TIMELINE_TRACKER_WAIT:
+		return "WAIT";
+	case MALI_TIMELINE_TRACKER_SYNC:
+		return "SYNC";
+	default:
+		return "INVALID";
+	}
+}
+
+mali_timeline_tracker_state mali_timeline_debug_get_tracker_state(struct mali_timeline_tracker *tracker)
+{
+	struct mali_timeline *timeline = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	timeline = tracker->timeline;
+
+	if (0 != tracker->trigger_ref_count) {
+		return MALI_TIMELINE_TS_WAITING;
+	}
+
+	if (timeline && (timeline->tracker_tail == tracker || NULL != tracker->timeline_prev)) {
+		return MALI_TIMELINE_TS_ACTIVE;
+	}
+
+	if (timeline && (MALI_TIMELINE_NO_POINT == tracker->point)) {
+		return MALI_TIMELINE_TS_INIT;
+	}
+
+	return MALI_TIMELINE_TS_FINISH;
+}
+
+void mali_timeline_debug_print_tracker(struct mali_timeline_tracker *tracker, _mali_osk_print_ctx *print_ctx)
+{
+	const char *tracker_state = "IWAF";
+	char state_char = 'I';
+	char tracker_type[32] = {0};
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	state_char = *(tracker_state + mali_timeline_debug_get_tracker_state(tracker));
+	_mali_osk_snprintf(tracker_type, sizeof(tracker_type), "%s", timeline_tracker_type_to_string(tracker->type));
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (0 != tracker->trigger_ref_count) {
+		if (print_ctx)
+			_mali_osk_ctxprintf(print_ctx, "TL:  %s %u %c - ref_wait:%u [%s(%u),%s(%u),%s(%u), fd:%d, fence:(0x%08X)]  job:(0x%08X)\n",
+					    tracker_type, tracker->point, state_char, tracker->trigger_ref_count,
+					    is_waiting_on_timeline(tracker, MALI_TIMELINE_GP) ? "WaitGP" : " ", tracker->fence.points[0],
+					    is_waiting_on_timeline(tracker, MALI_TIMELINE_PP) ? "WaitPP" : " ", tracker->fence.points[1],
+					    is_waiting_on_timeline(tracker, MALI_TIMELINE_SOFT) ? "WaitSOFT" : " ", tracker->fence.points[2],
+					    tracker->fence.sync_fd, (unsigned int)(uintptr_t)(tracker->sync_fence), (unsigned int)(uintptr_t)(tracker->job));
+		else
+			MALI_DEBUG_PRINT(2, ("TL:  %s %u %c - ref_wait:%u [%s(%u),%s(%u),%s(%u), fd:%d, fence:(0x%08X)]  job:(0x%08X)\n",
+					     tracker_type, tracker->point, state_char, tracker->trigger_ref_count,
+					     is_waiting_on_timeline(tracker, MALI_TIMELINE_GP) ? "WaitGP" : " ", tracker->fence.points[0],
+					     is_waiting_on_timeline(tracker, MALI_TIMELINE_PP) ? "WaitPP" : " ", tracker->fence.points[1],
+					     is_waiting_on_timeline(tracker, MALI_TIMELINE_SOFT) ? "WaitSOFT" : " ", tracker->fence.points[2],
+					     tracker->fence.sync_fd, (unsigned int)(uintptr_t)(tracker->sync_fence), (unsigned int)(uintptr_t)(tracker->job)));
+	} else {
+		if (print_ctx)
+			_mali_osk_ctxprintf(print_ctx, "TL:  %s %u %c  fd:%d  fence:(0x%08X)  job:(0x%08X)\n",
+					    tracker_type, tracker->point, state_char,
+					    tracker->fence.sync_fd, (unsigned int)(uintptr_t)(tracker->sync_fence), (unsigned int)(uintptr_t)(tracker->job));
+		else
+			MALI_DEBUG_PRINT(2, ("TL:  %s %u %c  fd:%d  fence:(0x%08X)  job:(0x%08X)\n",
+					     tracker_type, tracker->point, state_char,
+					     tracker->fence.sync_fd, (unsigned int)(uintptr_t)(tracker->sync_fence), (unsigned int)(uintptr_t)(tracker->job)));
+
+	}
+#else
+	if (0 != tracker->trigger_ref_count) {
+		if (print_ctx)
+			_mali_osk_ctxprintf(print_ctx, "TL:  %s %u %c - ref_wait:%u [%s(%u),%s(%u),%s(%u)]  job:(0x%08X)\n",
+					    tracker_type, tracker->point, state_char, tracker->trigger_ref_count,
+					    is_waiting_on_timeline(tracker, MALI_TIMELINE_GP) ? "WaitGP" : " ", tracker->fence.points[0],
+					    is_waiting_on_timeline(tracker, MALI_TIMELINE_PP) ? "WaitPP" : " ", tracker->fence.points[1],
+					    is_waiting_on_timeline(tracker, MALI_TIMELINE_SOFT) ? "WaitSOFT" : " ", tracker->fence.points[2],
+					    (unsigned int)(uintptr_t)(tracker->job));
+		else
+			MALI_DEBUG_PRINT(2, ("TL:  %s %u %c - ref_wait:%u [%s(%u),%s(%u),%s(%u)]  job:(0x%08X)\n",
+					     tracker_type, tracker->point, state_char, tracker->trigger_ref_count,
+					     is_waiting_on_timeline(tracker, MALI_TIMELINE_GP) ? "WaitGP" : " ", tracker->fence.points[0],
+					     is_waiting_on_timeline(tracker, MALI_TIMELINE_PP) ? "WaitPP" : " ", tracker->fence.points[1],
+					     is_waiting_on_timeline(tracker, MALI_TIMELINE_SOFT) ? "WaitSOFT" : " ", tracker->fence.points[2],
+					     (unsigned int)(uintptr_t)(tracker->job)));
+	} else {
+		if (print_ctx)
+			_mali_osk_ctxprintf(print_ctx, "TL:  %s %u %c  job:(0x%08X)\n",
+					    tracker_type, tracker->point, state_char,
+					    (unsigned int)(uintptr_t)(tracker->job));
+		else
+			MALI_DEBUG_PRINT(2, ("TL:  %s %u %c  job:(0x%08X)\n",
+					     tracker_type, tracker->point, state_char,
+					     (unsigned int)(uintptr_t)(tracker->job)));
+
+	}
+#endif
+}
+
+void mali_timeline_debug_print_timeline(struct mali_timeline *timeline, _mali_osk_print_ctx *print_ctx)
+{
+	struct mali_timeline_tracker *tracker = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	tracker = timeline->tracker_tail;
+	while (NULL != tracker) {
+		mali_timeline_debug_print_tracker(tracker, print_ctx);
+		tracker = tracker->timeline_next;
+	}
+}
+
+#if !(LINUX_VERSION_CODE < KERNEL_VERSION(3, 17, 0))
+void mali_timeline_debug_direct_print_tracker(struct mali_timeline_tracker *tracker)
+{
+	const char *tracker_state = "IWAF";
+	char state_char = 'I';
+	char tracker_type[32] = {0};
+
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	state_char = *(tracker_state + mali_timeline_debug_get_tracker_state(tracker));
+	_mali_osk_snprintf(tracker_type, sizeof(tracker_type), "%s", timeline_tracker_type_to_string(tracker->type));
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (0 != tracker->trigger_ref_count) {
+		MALI_PRINT(("TL:  %s %u %c - ref_wait:%u [%s(%u),%s(%u),%s(%u), fd:%d, fence:(0x%08X)]  job:(0x%08X)\n",
+			    tracker_type, tracker->point, state_char, tracker->trigger_ref_count,
+			    is_waiting_on_timeline(tracker, MALI_TIMELINE_GP) ? "WaitGP" : " ", tracker->fence.points[0],
+			    is_waiting_on_timeline(tracker, MALI_TIMELINE_PP) ? "WaitPP" : " ", tracker->fence.points[1],
+			    is_waiting_on_timeline(tracker, MALI_TIMELINE_SOFT) ? "WaitSOFT" : " ", tracker->fence.points[2],
+			    tracker->fence.sync_fd, tracker->sync_fence, tracker->job));
+	} else {
+		MALI_PRINT(("TL:  %s %u %c  fd:%d  fence:(0x%08X)  job:(0x%08X)\n",
+			    tracker_type, tracker->point, state_char,
+			    tracker->fence.sync_fd, tracker->sync_fence, tracker->job));
+	}
+#else
+	if (0 != tracker->trigger_ref_count) {
+		MALI_PRINT(("TL:  %s %u %c - ref_wait:%u [%s(%u),%s(%u),%s(%u)]  job:(0x%08X)\n",
+			    tracker_type, tracker->point, state_char, tracker->trigger_ref_count,
+			    is_waiting_on_timeline(tracker, MALI_TIMELINE_GP) ? "WaitGP" : " ", tracker->fence.points[0],
+			    is_waiting_on_timeline(tracker, MALI_TIMELINE_PP) ? "WaitPP" : " ", tracker->fence.points[1],
+			    is_waiting_on_timeline(tracker, MALI_TIMELINE_SOFT) ? "WaitSOFT" : " ", tracker->fence.points[2],
+			    tracker->job));
+	} else {
+		MALI_PRINT(("TL:  %s %u %c  job:(0x%08X)\n",
+			    tracker_type, tracker->point, state_char,
+			    tracker->job));
+	}
+#endif
+}
+
+void mali_timeline_debug_direct_print_timeline(struct mali_timeline *timeline)
+{
+	struct mali_timeline_tracker *tracker = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	tracker = timeline->tracker_tail;
+	while (NULL != tracker) {
+		mali_timeline_debug_direct_print_tracker(tracker);
+		tracker = tracker->timeline_next;
+	}
+}
+
+#endif
+
+void mali_timeline_debug_print_system(struct mali_timeline_system *system, _mali_osk_print_ctx *print_ctx)
+{
+	int i;
+	int num_printed = 0;
+	u32 tid = _mali_osk_get_tid();
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	/* Print all timelines */
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline = system->timelines[i];
+
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		if (NULL == timeline->tracker_head) continue;
+		if (print_ctx)
+			_mali_osk_ctxprintf(print_ctx, "TL: Timeline %s:\n",
+					    timeline_id_to_string((enum mali_timeline_id)i));
+		else
+			MALI_DEBUG_PRINT(2, ("TL: Timeline %s: oldest (%u) next(%u)\n",
+					     timeline_id_to_string((enum mali_timeline_id)i), timeline->point_oldest, timeline->point_next));
+
+		mali_timeline_debug_print_timeline(timeline, print_ctx);
+		num_printed++;
+	}
+
+	if (0 == num_printed) {
+		if (print_ctx)
+			_mali_osk_ctxprintf(print_ctx, "TL: All timelines empty\n");
+		else
+			MALI_DEBUG_PRINT(2, ("TL: All timelines empty\n"));
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+}
+
+#endif /* defined(MALI_TIMELINE_DEBUG_FUNCTIONS) */
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+void mali_timeline_dma_fence_callback(void *pp_job_ptr)
+{
+	struct mali_timeline_system  *system;
+	struct mali_timeline_waiter  *waiter;
+	struct mali_timeline_tracker *tracker;
+	struct mali_pp_job *pp_job = (struct mali_pp_job *)pp_job_ptr;
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+	u32 tid = _mali_osk_get_tid();
+	mali_bool is_aborting = MALI_FALSE;
+
+	MALI_DEBUG_ASSERT_POINTER(pp_job);
+
+	tracker = &pp_job->tracker;
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+
+	system = tracker->system;
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(system->session);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	waiter = tracker->waiter_dma_fence;
+	MALI_DEBUG_ASSERT_POINTER(waiter);
+
+	schedule_mask |= mali_timeline_system_release_waiter(system, waiter);
+
+	is_aborting = system->session->is_aborting;
+
+	/* If aborting, wake up sleepers that are waiting for dma fence callbacks to complete. */
+	if (is_aborting) {
+		_mali_osk_wait_queue_wake_up(system->wait_queue);
+	}
+
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+	if (!is_aborting) {
+		mali_executor_schedule_from_mask(schedule_mask, MALI_TRUE);
+	}
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_timeline.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_timeline.h
@@ -0,0 +1,588 @@
+/*
+ * Copyright (C) 2013-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_TIMELINE_H__
+#define __MALI_TIMELINE_H__
+
+#include "mali_osk.h"
+#include "mali_ukk.h"
+#include "mali_session.h"
+#include "mali_kernel_common.h"
+#include "mali_spinlock_reentrant.h"
+#include "mali_sync.h"
+#include "mali_scheduler_types.h"
+#include <linux/version.h>
+
+/**
+ * Soft job timeout.
+ *
+ * Soft jobs have to be signaled as complete after activation.  Normally this is done by user space,
+ * but in order to guarantee that every soft job is completed, we also have a timer.
+ */
+#define MALI_TIMELINE_TIMEOUT_HZ ((unsigned long) (HZ * 3 / 2)) /* 1500 ms. */
+
+/**
+ * Timeline type.
+ */
+typedef enum mali_timeline_id {
+	MALI_TIMELINE_GP   = MALI_UK_TIMELINE_GP,   /**< GP job timeline. */
+	MALI_TIMELINE_PP   = MALI_UK_TIMELINE_PP,   /**< PP job timeline. */
+	MALI_TIMELINE_SOFT = MALI_UK_TIMELINE_SOFT, /**< Soft job timeline. */
+	MALI_TIMELINE_MAX  = MALI_UK_TIMELINE_MAX
+} mali_timeline_id;
+
+/**
+ * Used by trackers that should not be added to a timeline (@ref mali_timeline_system_add_tracker).
+ */
+#define MALI_TIMELINE_NONE MALI_TIMELINE_MAX
+
+/**
+ * Tracker type.
+ */
+typedef enum mali_timeline_tracker_type {
+	MALI_TIMELINE_TRACKER_GP   = 0, /**< Tracker used by GP jobs. */
+	MALI_TIMELINE_TRACKER_PP   = 1, /**< Tracker used by PP jobs. */
+	MALI_TIMELINE_TRACKER_SOFT = 2, /**< Tracker used by soft jobs. */
+	MALI_TIMELINE_TRACKER_WAIT = 3, /**< Tracker used for fence wait. */
+	MALI_TIMELINE_TRACKER_SYNC = 4, /**< Tracker used for sync fence. */
+	MALI_TIMELINE_TRACKER_MAX  = 5,
+} mali_timeline_tracker_type;
+
+/**
+ * Tracker activation error.
+ */
+typedef u32 mali_timeline_activation_error;
+#define MALI_TIMELINE_ACTIVATION_ERROR_NONE      0
+#define MALI_TIMELINE_ACTIVATION_ERROR_SYNC_BIT  (1<<1)
+#define MALI_TIMELINE_ACTIVATION_ERROR_FATAL_BIT (1<<0)
+
+/**
+ * Type used to represent a point on a timeline.
+ */
+typedef u32 mali_timeline_point;
+
+/**
+ * Used to represent that no point on a timeline.
+ */
+#define MALI_TIMELINE_NO_POINT ((mali_timeline_point) 0)
+
+/**
+ * The maximum span of points on a timeline.  A timeline will be considered full if the difference
+ * between the oldest and newest points is equal or larger to this value.
+ */
+#define MALI_TIMELINE_MAX_POINT_SPAN 65536
+
+/**
+ * Magic value used to assert on validity of trackers.
+ */
+#define MALI_TIMELINE_TRACKER_MAGIC 0xabcdabcd
+
+struct mali_timeline;
+struct mali_timeline_waiter;
+struct mali_timeline_tracker;
+
+/**
+ * Timeline fence.
+ */
+struct mali_timeline_fence {
+	mali_timeline_point points[MALI_TIMELINE_MAX]; /**< For each timeline, a point or MALI_TIMELINE_NO_POINT. */
+	s32                 sync_fd;                   /**< A file descriptor representing a sync fence, or -1. */
+};
+
+/**
+ * Timeline system.
+ *
+ * The Timeline system has a set of timelines associated with a session.
+ */
+struct mali_timeline_system {
+	struct mali_spinlock_reentrant *spinlock;   /**< Spin lock protecting the timeline system */
+	struct mali_timeline           *timelines[MALI_TIMELINE_MAX]; /**< The timelines in this system */
+
+	/* Single-linked list of unused waiter objects.  Uses the tracker_next field in tracker. */
+	struct mali_timeline_waiter    *waiter_empty_list;
+
+	struct mali_session_data       *session;    /**< Session that owns this system. */
+
+	mali_bool                       timer_enabled; /**< Set to MALI_TRUE if soft job timer should be enabled, MALI_FALSE if not. */
+
+	_mali_osk_wait_queue_t         *wait_queue; /**< Wait queue. */
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_timeline           *signaled_sync_tl; /**< Special sync timeline used to create pre-signaled sync fences */
+#else
+	struct mali_internal_sync_timeline           *signaled_sync_tl; /**< Special sync timeline used to create pre-signaled sync fences */
+#endif
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+};
+
+/**
+ * Timeline.  Each Timeline system will have MALI_TIMELINE_MAX timelines.
+ */
+struct mali_timeline {
+	mali_timeline_point           point_next;   /**< The next available point. */
+	mali_timeline_point           point_oldest; /**< The oldest point not released. */
+
+	/* Double-linked list of trackers.  Sorted in ascending order by tracker->time_number with
+	 * tail pointing to the tracker with the oldest time. */
+	struct mali_timeline_tracker *tracker_head;
+	struct mali_timeline_tracker *tracker_tail;
+
+	/* Double-linked list of waiters.  Sorted in ascending order by waiter->time_number_wait
+	 * with tail pointing to the waiter with oldest wait time. */
+	struct mali_timeline_waiter  *waiter_head;
+	struct mali_timeline_waiter  *waiter_tail;
+
+	struct mali_timeline_system  *system;       /**< Timeline system this timeline belongs to. */
+	enum mali_timeline_id         id;           /**< Timeline type. */
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_timeline         *sync_tl;      /**< Sync timeline that corresponds to this timeline. */
+#else
+	struct mali_internal_sync_timeline *sync_tl;
+#endif
+	mali_bool destroyed;
+	struct mali_spinlock_reentrant *spinlock;       /**< Spin lock protecting the timeline system */
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	/* The following fields are used to time out soft job trackers. */
+	_mali_osk_wq_delayed_work_t  *delayed_work;
+	mali_bool                     timer_active;
+};
+
+/**
+ * Timeline waiter.
+ */
+struct mali_timeline_waiter {
+	mali_timeline_point           point;         /**< Point on timeline we are waiting for to be released. */
+	struct mali_timeline_tracker *tracker;       /**< Tracker that is waiting. */
+
+	struct mali_timeline_waiter  *timeline_next; /**< Next waiter on timeline's waiter list. */
+	struct mali_timeline_waiter  *timeline_prev; /**< Previous waiter on timeline's waiter list. */
+
+	struct mali_timeline_waiter  *tracker_next;  /**< Next waiter on tracker's waiter list. */
+};
+
+/**
+ * Timeline tracker.
+ */
+struct mali_timeline_tracker {
+	MALI_DEBUG_CODE(u32            magic); /**< Should always be MALI_TIMELINE_TRACKER_MAGIC for a valid tracker. */
+
+	mali_timeline_point            point; /**< Point on timeline for this tracker */
+
+	struct mali_timeline_tracker  *timeline_next; /**< Next tracker on timeline's tracker list */
+	struct mali_timeline_tracker  *timeline_prev; /**< Previous tracker on timeline's tracker list */
+
+	u32                            trigger_ref_count; /**< When zero tracker will be activated */
+	mali_timeline_activation_error activation_error;  /**< Activation error. */
+	struct mali_timeline_fence     fence;             /**< Fence used to create this tracker */
+
+	/* Single-linked list of waiters.  Sorted in order of insertions with
+	 * tail pointing to first waiter. */
+	struct mali_timeline_waiter   *waiter_head;
+	struct mali_timeline_waiter   *waiter_tail;
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	/* These are only used if the tracker is waiting on a sync fence. */
+	struct mali_timeline_waiter   *waiter_sync; /**< A direct pointer to timeline waiter representing sync fence. */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_fence_waiter       sync_fence_waiter; /**< Used to connect sync fence and tracker in sync fence wait callback. */
+	struct sync_fence             *sync_fence;   /**< The sync fence this tracker is waiting on. */
+#else
+	struct mali_internal_sync_fence_waiter       sync_fence_waiter; /**< Used to connect sync fence and tracker in sync fence wait callback. */
+	struct mali_internal_sync_fence             *sync_fence;   /**< The sync fence this tracker is waiting on. */
+#endif
+	_mali_osk_list_t               sync_fence_cancel_list; /**< List node used to cancel sync fence waiters. */
+	_mali_osk_list_t                sync_fence_signal_list; /** < List node used to singal sync fence callback function. */
+
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+	struct mali_timeline_waiter   *waiter_dma_fence; /**< A direct pointer to timeline waiter representing dma fence. */
+#endif
+
+	struct mali_timeline_system   *system;       /**< Timeline system. */
+	struct mali_timeline          *timeline;     /**< Timeline, or NULL if not on a timeline. */
+	enum mali_timeline_tracker_type type;        /**< Type of tracker. */
+	void                          *job;          /**< Owner of tracker. */
+
+	/* The following fields are used to time out soft job trackers. */
+	unsigned long                 os_tick_create;
+	unsigned long                 os_tick_activate;
+	mali_bool                     timer_active;
+};
+
+extern _mali_osk_atomic_t gp_tracker_count;
+extern _mali_osk_atomic_t phy_pp_tracker_count;
+extern _mali_osk_atomic_t virt_pp_tracker_count;
+
+/**
+ * What follows is a set of functions to check the state of a timeline and to determine where on a
+ * timeline a given point is.  Most of these checks will translate the timeline so the oldest point
+ * on the timeline is aligned with zero.  Remember that all of these calculation are done on
+ * unsigned integers.
+ *
+ * The following example illustrates the three different states a point can be in.  The timeline has
+ * been translated to put the oldest point at zero:
+ *
+ *
+ *
+ *                               [ point is in forbidden zone ]
+ *                                          64k wide
+ *                                MALI_TIMELINE_MAX_POINT_SPAN
+ *
+ *    [ point is on timeline     )                            ( point is released ]
+ *
+ *    0--------------------------##############################--------------------2^32 - 1
+ *    ^                          ^
+ *    \                          |
+ *     oldest point on timeline  |
+ *                               \
+ *                                next point on timeline
+ */
+
+/**
+ * Compare two timeline points
+ *
+ * Returns true if a is after b, false if a is before or equal to b.
+ *
+ * This funcion ignores MALI_TIMELINE_MAX_POINT_SPAN. Wrapping is supported and
+ * the result will be correct if the points is less then UINT_MAX/2 apart.
+ *
+ * @param a Point on timeline
+ * @param b Point on timeline
+ * @return MALI_TRUE if a is after b
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_point_after(mali_timeline_point a, mali_timeline_point b)
+{
+	return 0 > ((s32)b) - ((s32)a);
+}
+
+/**
+ * Check if a point is on timeline.  A point is on a timeline if it is greater than, or equal to,
+ * the oldest point, and less than the next point.
+ *
+ * @param timeline Timeline.
+ * @param point Point on timeline.
+ * @return MALI_TRUE if point is on timeline, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_is_point_on(struct mali_timeline *timeline, mali_timeline_point point)
+{
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_NO_POINT != point);
+
+	return (point - timeline->point_oldest) < (timeline->point_next - timeline->point_oldest);
+}
+
+/**
+ * Check if a point has been released.  A point is released if it is older than the oldest point on
+ * the timeline, newer than the next point, and also not in the forbidden zone.
+ *
+ * @param timeline Timeline.
+ * @param point Point on timeline.
+ * @return MALI_TRUE if point has been release, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_is_point_released(struct mali_timeline *timeline, mali_timeline_point point)
+{
+	mali_timeline_point point_normalized;
+	mali_timeline_point next_normalized;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_NO_POINT != point);
+
+	point_normalized = point - timeline->point_oldest;
+	next_normalized = timeline->point_next - timeline->point_oldest;
+
+	return point_normalized > (next_normalized + MALI_TIMELINE_MAX_POINT_SPAN);
+}
+
+/**
+ * Check if the tracker that the point relate to has been released.  A point is released if the tracker is not on the timeline.
+ * @param timeline Timeline.
+ * @param point Point on timeline.
+ * @return MALI_TRUE if the tracker has been release, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_is_tracker_released(struct mali_timeline *timeline, mali_timeline_point point)
+{
+	struct mali_timeline_tracker *tracker;
+	
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_NO_POINT != point);
+
+	tracker = timeline->tracker_tail;
+
+	while (NULL != tracker) {
+		if (point == tracker->point)
+			return MALI_FALSE;
+		tracker = tracker->timeline_next;
+	}
+
+	return MALI_TRUE;
+}
+
+
+/**
+ * Check if a point is valid.  A point is valid if is on the timeline or has been released.
+ *
+ * @param timeline Timeline.
+ * @param point Point on timeline.
+ * @return MALI_TRUE if point is valid, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_is_point_valid(struct mali_timeline *timeline, mali_timeline_point point)
+{
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	return mali_timeline_is_point_on(timeline, point) || mali_timeline_is_point_released(timeline, point);
+}
+
+/**
+ * Check if timeline is empty (has no points on it).  A timeline is empty if next == oldest.
+ *
+ * @param timeline Timeline.
+ * @return MALI_TRUE if timeline is empty, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_is_empty(struct mali_timeline *timeline)
+{
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	return timeline->point_next == timeline->point_oldest;
+}
+
+/**
+ * Check if timeline is full.  A valid timeline cannot span more than 64k points (@ref
+ * MALI_TIMELINE_MAX_POINT_SPAN).
+ *
+ * @param timeline Timeline.
+ * @return MALI_TRUE if timeline is full, MALI_FALSE if not.
+ */
+MALI_STATIC_INLINE mali_bool mali_timeline_is_full(struct mali_timeline *timeline)
+{
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	return MALI_TIMELINE_MAX_POINT_SPAN <= (timeline->point_next - timeline->point_oldest);
+}
+
+/**
+ * Create a new timeline system.
+ *
+ * @param session The session this timeline system will belong to.
+ * @return New timeline system.
+ */
+struct mali_timeline_system *mali_timeline_system_create(struct mali_session_data *session);
+
+/**
+ * Abort timeline system.
+ *
+ * This will release all pending waiters in the timeline system causing all trackers to be
+ * activated.
+ *
+ * @param system Timeline system to abort all jobs from.
+ */
+void mali_timeline_system_abort(struct mali_timeline_system *system);
+
+/**
+ * Destroy an empty timeline system.
+ *
+ * @note @ref mali_timeline_system_abort() should be called prior to this function.
+ *
+ * @param system Timeline system to destroy.
+ */
+void mali_timeline_system_destroy(struct mali_timeline_system *system);
+
+/**
+ * Stop the soft job timer.
+ *
+ * @param system Timeline system
+ */
+void mali_timeline_system_stop_timer(struct mali_timeline_system *system);
+
+/**
+ * Add a tracker to a timeline system and optionally also on a timeline.
+ *
+ * Once added to the timeline system, the tracker is guaranteed to be activated.  The tracker can be
+ * activated before this function returns.  Thus, it is also possible that the tracker is released
+ * before this function returns, depending on the tracker type.
+ *
+ * @note Tracker must be initialized (@ref mali_timeline_tracker_init) before being added to the
+ * timeline system.
+ *
+ * @param system Timeline system the tracker will be added to.
+ * @param tracker The tracker to be added.
+ * @param timeline_id Id of the timeline the tracker will be added to, or
+ *                    MALI_TIMELINE_NONE if it should not be added on a timeline.
+ * @return Point on timeline identifying this tracker, or MALI_TIMELINE_NO_POINT if not on timeline.
+ */
+mali_timeline_point mali_timeline_system_add_tracker(struct mali_timeline_system *system,
+		struct mali_timeline_tracker *tracker,
+		enum mali_timeline_id timeline_id);
+
+/**
+ * Get latest point on timeline.
+ *
+ * @param system Timeline system.
+ * @param timeline_id Id of timeline to get latest point from.
+ * @return Latest point on timeline, or MALI_TIMELINE_NO_POINT if the timeline is empty.
+ */
+mali_timeline_point mali_timeline_system_get_latest_point(struct mali_timeline_system *system,
+		enum mali_timeline_id timeline_id);
+
+/**
+ * Initialize tracker.
+ *
+ * Must be called before tracker is added to timeline system (@ref mali_timeline_system_add_tracker).
+ *
+ * @param tracker Tracker to initialize.
+ * @param type Type of tracker.
+ * @param fence Fence used to set up dependencies for tracker.
+ * @param job Pointer to job struct this tracker is associated with.
+ */
+void mali_timeline_tracker_init(struct mali_timeline_tracker *tracker,
+				mali_timeline_tracker_type type,
+				struct mali_timeline_fence *fence,
+				void *job);
+
+/**
+ * Grab trigger ref count on tracker.
+ *
+ * This will prevent tracker from being activated until the trigger ref count reaches zero.
+ *
+ * @note Tracker must have been initialized (@ref mali_timeline_tracker_init).
+ *
+ * @param system Timeline system.
+ * @param tracker Tracker.
+ */
+void mali_timeline_system_tracker_get(struct mali_timeline_system *system, struct mali_timeline_tracker *tracker);
+
+/**
+ * Release trigger ref count on tracker.
+ *
+ * If the trigger ref count reaches zero, the tracker will be activated.
+ *
+ * @param system Timeline system.
+ * @param tracker Tracker.
+ * @param activation_error Error bitmask if activated with error, or MALI_TIMELINE_ACTIVATION_ERROR_NONE if no error.
+ * @return Scheduling bitmask.
+ */
+mali_scheduler_mask mali_timeline_system_tracker_put(struct mali_timeline_system *system, struct mali_timeline_tracker *tracker, mali_timeline_activation_error activation_error);
+
+/**
+ * Release a tracker from the timeline system.
+ *
+ * This is used to signal that the job being tracker is finished, either due to normal circumstances
+ * (job complete/abort) or due to a timeout.
+ *
+ * We may need to schedule some subsystems after a tracker has been released and the returned
+ * bitmask will tell us if it is necessary.  If the return value is non-zero, this value needs to be
+ * sent as an input parameter to @ref mali_scheduler_schedule_from_mask() to do the scheduling.
+ *
+ * @note Tracker must have been activated before being released.
+ * @warning Not calling @ref mali_scheduler_schedule_from_mask() after releasing a tracker can lead
+ * to a deadlock.
+ *
+ * @param tracker Tracker being released.
+ * @return Scheduling bitmask.
+ */
+mali_scheduler_mask mali_timeline_tracker_release(struct mali_timeline_tracker *tracker);
+
+MALI_STATIC_INLINE mali_bool mali_timeline_tracker_activation_error(
+	struct mali_timeline_tracker *tracker)
+{
+	MALI_DEBUG_ASSERT_POINTER(tracker);
+	return (MALI_TIMELINE_ACTIVATION_ERROR_FATAL_BIT &
+		tracker->activation_error) ? MALI_TRUE : MALI_FALSE;
+}
+
+/**
+ * Copy data from a UK fence to a Timeline fence.
+ *
+ * @param fence Timeline fence.
+ * @param uk_fence UK fence.
+ */
+void mali_timeline_fence_copy_uk_fence(struct mali_timeline_fence *fence, _mali_uk_fence_t *uk_fence);
+
+_mali_osk_errcode_t mali_timeline_initialize(void);
+
+void mali_timeline_terminate(void);
+
+MALI_STATIC_INLINE mali_bool mali_timeline_has_gp_job(void)
+{
+	return 0 < _mali_osk_atomic_read(&gp_tracker_count);
+}
+
+MALI_STATIC_INLINE mali_bool mali_timeline_has_physical_pp_job(void)
+{
+	return 0 < _mali_osk_atomic_read(&phy_pp_tracker_count);
+}
+
+MALI_STATIC_INLINE mali_bool mali_timeline_has_virtual_pp_job(void)
+{
+	return 0 < _mali_osk_atomic_read(&virt_pp_tracker_count);
+}
+
+#if defined(DEBUG)
+#define MALI_TIMELINE_DEBUG_FUNCTIONS
+#endif /* DEBUG */
+#if defined(MALI_TIMELINE_DEBUG_FUNCTIONS)
+
+/**
+ * Tracker state.  Used for debug printing.
+ */
+typedef enum mali_timeline_tracker_state {
+	MALI_TIMELINE_TS_INIT    = 0,
+	MALI_TIMELINE_TS_WAITING = 1,
+	MALI_TIMELINE_TS_ACTIVE  = 2,
+	MALI_TIMELINE_TS_FINISH  = 3,
+} mali_timeline_tracker_state;
+
+/**
+ * Get tracker state.
+ *
+ * @param tracker Tracker to check.
+ * @return State of tracker.
+ */
+mali_timeline_tracker_state mali_timeline_debug_get_tracker_state(struct mali_timeline_tracker *tracker);
+
+/**
+ * Print debug information about tracker.
+ *
+ * @param tracker Tracker to print.
+ */
+void mali_timeline_debug_print_tracker(struct mali_timeline_tracker *tracker, _mali_osk_print_ctx *print_ctx);
+
+/**
+ * Print debug information about timeline.
+ *
+ * @param timeline Timeline to print.
+ */
+void mali_timeline_debug_print_timeline(struct mali_timeline *timeline, _mali_osk_print_ctx *print_ctx);
+
+#if !(LINUX_VERSION_CODE < KERNEL_VERSION(3, 17, 0))
+void mali_timeline_debug_direct_print_tracker(struct mali_timeline_tracker *tracker);
+void mali_timeline_debug_direct_print_timeline(struct mali_timeline *timeline);
+#endif
+
+/**
+ * Print debug information about timeline system.
+ *
+ * @param system Timeline system to print.
+ */
+void mali_timeline_debug_print_system(struct mali_timeline_system *system, _mali_osk_print_ctx *print_ctx);
+
+#endif /* defined(MALI_TIMELINE_DEBUG_FUNCTIONS) */
+
+#if defined(CONFIG_MALI_DMA_BUF_FENCE)
+/**
+ * The timeline dma fence callback when dma fence signal.
+ *
+ * @param pp_job_ptr The pointer to pp job that link to the signaled dma fence.
+ */
+void mali_timeline_dma_fence_callback(void *pp_job_ptr);
+#endif
+
+#endif /* __MALI_TIMELINE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_timeline_fence_wait.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_timeline_fence_wait.c
@@ -0,0 +1,218 @@
+/*
+ * Copyright (C) 2013-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/file.h>
+#include "mali_timeline_fence_wait.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_spinlock_reentrant.h"
+
+/**
+ * Allocate a fence waiter tracker.
+ *
+ * @return New fence waiter if successful, NULL if not.
+ */
+static struct mali_timeline_fence_wait_tracker *mali_timeline_fence_wait_tracker_alloc(void)
+{
+	return (struct mali_timeline_fence_wait_tracker *) _mali_osk_calloc(1, sizeof(struct mali_timeline_fence_wait_tracker));
+}
+
+/**
+ * Free fence waiter tracker.
+ *
+ * @param wait Fence wait tracker to free.
+ */
+static void mali_timeline_fence_wait_tracker_free(struct mali_timeline_fence_wait_tracker *wait)
+{
+	MALI_DEBUG_ASSERT_POINTER(wait);
+	_mali_osk_atomic_term(&wait->refcount);
+	_mali_osk_free(wait);
+}
+
+/**
+ * Check if fence wait tracker has been activated.  Used as a wait queue condition.
+ *
+ * @param data Fence waiter.
+ * @return MALI_TRUE if tracker has been activated, MALI_FALSE if not.
+ */
+static mali_bool mali_timeline_fence_wait_tracker_is_activated(void *data)
+{
+	struct mali_timeline_fence_wait_tracker *wait;
+
+	wait = (struct mali_timeline_fence_wait_tracker *) data;
+	MALI_DEBUG_ASSERT_POINTER(wait);
+
+	return wait->activated;
+}
+
+/**
+ * Check if fence has been signaled.
+ *
+ * @param system Timeline system.
+ * @param fence Timeline fence.
+ * @return MALI_TRUE if fence is signaled, MALI_FALSE if not.
+ */
+static mali_bool mali_timeline_fence_wait_check_status(struct mali_timeline_system *system, struct mali_timeline_fence *fence)
+{
+	int i;
+	u32 tid = _mali_osk_get_tid();
+	mali_bool ret = MALI_TRUE;
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_fence *sync_fence = NULL;
+#else
+	struct mali_internal_sync_fence *sync_fence = NULL;
+#endif
+#endif
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	mali_spinlock_reentrant_wait(system->spinlock, tid);
+
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline;
+		mali_timeline_point   point;
+
+		point = fence->points[i];
+
+		if (likely(MALI_TIMELINE_NO_POINT == point)) {
+			/* Fence contains no point on this timeline. */
+			continue;
+		}
+
+		timeline = system->timelines[i];
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		if (unlikely(!mali_timeline_is_point_valid(timeline, point))) {
+			MALI_PRINT_ERROR(("Mali Timeline: point %d is not valid (oldest=%d, next=%d)\n", point, timeline->point_oldest, timeline->point_next));
+		}
+
+		if (!mali_timeline_is_point_released(timeline, point)) {
+			ret = MALI_FALSE;
+			goto exit;
+		}
+	}
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (-1 != fence->sync_fd) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence = sync_fence_fdget(fence->sync_fd);
+#else
+		sync_fence = mali_internal_sync_fence_fdget(fence->sync_fd);
+#endif
+		if (likely(NULL != sync_fence)) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 17, 0)
+			if (0 == sync_fence->status) {
+#elif LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+			if (0 < atomic_read(&sync_fence->status)) {
+#else
+			if (0 == sync_fence->fence->ops->signaled(sync_fence->fence)) {
+#endif
+				ret = MALI_FALSE;
+
+			} else {
+				ret = MALI_TRUE;
+			}
+		} else {
+			MALI_PRINT_ERROR(("Mali Timeline: failed to get sync fence from fd %d\n", fence->sync_fd));
+		}
+	}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+exit:
+	mali_spinlock_reentrant_signal(system->spinlock, tid);
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	if (NULL != sync_fence) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence_put(sync_fence);
+#else
+		fput(sync_fence->file);
+#endif
+	}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	return ret;
+}
+
+mali_bool mali_timeline_fence_wait(struct mali_timeline_system *system, struct mali_timeline_fence *fence, u32 timeout)
+{
+	struct mali_timeline_fence_wait_tracker *wait;
+	mali_timeline_point point;
+	mali_bool ret;
+
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	MALI_DEBUG_PRINT(4, ("Mali Timeline: wait on fence\n"));
+
+	if (MALI_TIMELINE_FENCE_WAIT_TIMEOUT_IMMEDIATELY == timeout) {
+		return mali_timeline_fence_wait_check_status(system, fence);
+	}
+
+	wait = mali_timeline_fence_wait_tracker_alloc();
+	if (unlikely(NULL == wait)) {
+		MALI_PRINT_ERROR(("Mali Timeline: failed to allocate data for fence wait\n"));
+		return MALI_FALSE;
+	}
+
+	wait->activated = MALI_FALSE;
+	wait->system = system;
+
+	/* Initialize refcount to two references.  The reference first will be released by this
+	 * function after the wait is over.  The second reference will be released when the tracker
+	 * is activated. */
+	_mali_osk_atomic_init(&wait->refcount, 2);
+
+	/* Add tracker to timeline system, but not to a timeline. */
+	mali_timeline_tracker_init(&wait->tracker, MALI_TIMELINE_TRACKER_WAIT, fence, wait);
+	point = mali_timeline_system_add_tracker(system, &wait->tracker, MALI_TIMELINE_NONE);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_NO_POINT == point);
+	MALI_IGNORE(point);
+
+	/* Wait for the tracker to be activated or time out. */
+	if (MALI_TIMELINE_FENCE_WAIT_TIMEOUT_NEVER == timeout) {
+		_mali_osk_wait_queue_wait_event(system->wait_queue, mali_timeline_fence_wait_tracker_is_activated, (void *) wait);
+	} else {
+		_mali_osk_wait_queue_wait_event_timeout(system->wait_queue, mali_timeline_fence_wait_tracker_is_activated, (void *) wait, timeout);
+	}
+
+	ret = wait->activated;
+
+	if (0 == _mali_osk_atomic_dec_return(&wait->refcount)) {
+		mali_timeline_fence_wait_tracker_free(wait);
+	}
+
+	return ret;
+}
+
+void mali_timeline_fence_wait_activate(struct mali_timeline_fence_wait_tracker *wait)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(wait);
+	MALI_DEBUG_ASSERT_POINTER(wait->system);
+
+	MALI_DEBUG_PRINT(4, ("Mali Timeline: activation for fence wait tracker\n"));
+
+	MALI_DEBUG_ASSERT(MALI_FALSE == wait->activated);
+	wait->activated = MALI_TRUE;
+
+	_mali_osk_wait_queue_wake_up(wait->system->wait_queue);
+
+	/* Nothing can wait on this tracker, so nothing to schedule after release. */
+	schedule_mask = mali_timeline_tracker_release(&wait->tracker);
+	MALI_DEBUG_ASSERT(MALI_SCHEDULER_MASK_EMPTY == schedule_mask);
+	MALI_IGNORE(schedule_mask);
+
+	if (0 == _mali_osk_atomic_dec_return(&wait->refcount)) {
+		mali_timeline_fence_wait_tracker_free(wait);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_timeline_fence_wait.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_timeline_fence_wait.h
@@ -0,0 +1,67 @@
+/*
+ * Copyright (C) 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_timeline_fence_wait.h
+ *
+ * This file contains functions used to wait until a Timeline fence is signaled.
+ */
+
+#ifndef __MALI_TIMELINE_FENCE_WAIT_H__
+#define __MALI_TIMELINE_FENCE_WAIT_H__
+
+#include "mali_osk.h"
+#include "mali_timeline.h"
+
+/**
+ * If used as the timeout argument in @ref mali_timeline_fence_wait, a timer is not used and the
+ * function only returns when the fence is signaled.
+ */
+#define MALI_TIMELINE_FENCE_WAIT_TIMEOUT_NEVER ((u32) -1)
+
+/**
+ * If used as the timeout argument in @ref mali_timeline_fence_wait, the function will return
+ * immediately with the current state of the fence.
+ */
+#define MALI_TIMELINE_FENCE_WAIT_TIMEOUT_IMMEDIATELY 0
+
+/**
+ * Fence wait tracker.
+ *
+ * The fence wait tracker is added to the Timeline system with the fence we are waiting on as a
+ * dependency.  We will then perform a blocking wait, possibly with a timeout, until the tracker is
+ * activated, which happens when the fence is signaled.
+ */
+struct mali_timeline_fence_wait_tracker {
+	mali_bool activated;                  /**< MALI_TRUE if the tracker has been activated, MALI_FALSE if not. */
+	_mali_osk_atomic_t refcount;          /**< Reference count. */
+	struct mali_timeline_system *system;  /**< Timeline system. */
+	struct mali_timeline_tracker tracker; /**< Timeline tracker. */
+};
+
+/**
+ * Wait for a fence to be signaled, or timeout is reached.
+ *
+ * @param system Timeline system.
+ * @param fence Fence to wait on.
+ * @param timeout Timeout in ms, or MALI_TIMELINE_FENCE_WAIT_TIMEOUT_NEVER or
+ * MALI_TIMELINE_FENCE_WAIT_TIMEOUT_IMMEDIATELY.
+ * @return MALI_TRUE if signaled, MALI_FALSE if timed out.
+ */
+mali_bool mali_timeline_fence_wait(struct mali_timeline_system *system, struct mali_timeline_fence *fence, u32 timeout);
+
+/**
+ * Used by the Timeline system to activate a fence wait tracker.
+ *
+ * @param fence_wait_tracker Fence waiter tracker.
+ */
+void mali_timeline_fence_wait_activate(struct mali_timeline_fence_wait_tracker *fence_wait_tracker);
+
+#endif /* __MALI_TIMELINE_FENCE_WAIT_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_timeline_sync_fence.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_timeline_sync_fence.c
@@ -0,0 +1,179 @@
+/*
+ * Copyright (C) 2013, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/file.h>
+#include "mali_timeline_sync_fence.h"
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_sync.h"
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+/**
+ * Creates a sync fence tracker and a sync fence.  Adds sync fence tracker to Timeline system and
+ * returns sync fence.  The sync fence will be signaled when the sync fence tracker is activated.
+ *
+ * @param timeline Timeline.
+ * @param point Point on timeline.
+ * @return Sync fence that will be signaled when tracker is activated.
+ */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static struct sync_fence *mali_timeline_sync_fence_create_and_add_tracker(struct mali_timeline *timeline, mali_timeline_point point)
+#else
+static struct mali_internal_sync_fence *mali_timeline_sync_fence_create_and_add_tracker(struct mali_timeline *timeline, mali_timeline_point point)
+#endif
+{
+	struct mali_timeline_sync_fence_tracker *sync_fence_tracker;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_fence                       *sync_fence;
+#else
+	struct mali_internal_sync_fence                       *sync_fence;
+#endif
+	struct mali_timeline_fence               fence;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_NO_POINT != point);
+
+	/* Allocate sync fence tracker. */
+	sync_fence_tracker = _mali_osk_calloc(1, sizeof(struct mali_timeline_sync_fence_tracker));
+	if (NULL == sync_fence_tracker) {
+		MALI_PRINT_ERROR(("Mali Timeline: sync_fence_tracker allocation failed\n"));
+		return NULL;
+	}
+
+	/* Create sync flag. */
+	MALI_DEBUG_ASSERT_POINTER(timeline->sync_tl);
+	sync_fence_tracker->flag = mali_sync_flag_create(timeline->sync_tl, point);
+	if (NULL == sync_fence_tracker->flag) {
+		MALI_PRINT_ERROR(("Mali Timeline: sync_flag creation failed\n"));
+		_mali_osk_free(sync_fence_tracker);
+		return NULL;
+	}
+
+	/* Create sync fence from sync flag. */
+	sync_fence = mali_sync_flag_create_fence(sync_fence_tracker->flag);
+	if (NULL == sync_fence) {
+		MALI_PRINT_ERROR(("Mali Timeline: sync_fence creation failed\n"));
+		mali_sync_flag_put(sync_fence_tracker->flag);
+		_mali_osk_free(sync_fence_tracker);
+		return NULL;
+	}
+
+	/* Setup fence for tracker. */
+	_mali_osk_memset(&fence, 0, sizeof(struct mali_timeline_fence));
+	fence.sync_fd = -1;
+	fence.points[timeline->id] = point;
+
+	/* Finally, add the tracker to Timeline system. */
+	mali_timeline_tracker_init(&sync_fence_tracker->tracker, MALI_TIMELINE_TRACKER_SYNC, &fence, sync_fence_tracker);
+	point = mali_timeline_system_add_tracker(timeline->system, &sync_fence_tracker->tracker, MALI_TIMELINE_NONE);
+	MALI_DEBUG_ASSERT(MALI_TIMELINE_NO_POINT == point);
+
+	return sync_fence;
+}
+
+s32 mali_timeline_sync_fence_create(struct mali_timeline_system *system, struct mali_timeline_fence *fence)
+{
+	u32 i;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_fence *sync_fence_acc = NULL;
+#else
+	struct mali_internal_sync_fence *sync_fence_acc = NULL;
+#endif
+	MALI_DEBUG_ASSERT_POINTER(system);
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	for (i = 0; i < MALI_TIMELINE_MAX; ++i) {
+		struct mali_timeline *timeline;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		struct sync_fence *sync_fence;
+#else
+		struct mali_internal_sync_fence *sync_fence;
+#endif
+		if (MALI_TIMELINE_NO_POINT == fence->points[i]) continue;
+
+		timeline = system->timelines[i];
+		MALI_DEBUG_ASSERT_POINTER(timeline);
+
+		sync_fence = mali_timeline_sync_fence_create_and_add_tracker(timeline, fence->points[i]);
+		if (NULL == sync_fence) goto error;
+
+		if (NULL != sync_fence_acc) {
+			/* Merge sync fences. */
+			sync_fence_acc = mali_sync_fence_merge(sync_fence_acc, sync_fence);
+			if (NULL == sync_fence_acc) goto error;
+		} else {
+			/* This was the first sync fence created. */
+			sync_fence_acc = sync_fence;
+		}
+	}
+
+	if (-1 != fence->sync_fd) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		struct sync_fence *sync_fence;
+		sync_fence = sync_fence_fdget(fence->sync_fd);
+#else
+		struct mali_internal_sync_fence *sync_fence;
+		sync_fence = mali_internal_sync_fence_fdget(fence->sync_fd);
+#endif
+
+		if (NULL == sync_fence) goto error;
+
+		if (NULL != sync_fence_acc) {
+			sync_fence_acc = mali_sync_fence_merge(sync_fence_acc, sync_fence);
+			if (NULL == sync_fence_acc) goto error;
+		} else {
+			sync_fence_acc = sync_fence;
+		}
+	}
+
+	if (NULL == sync_fence_acc) {
+		MALI_DEBUG_ASSERT_POINTER(system->signaled_sync_tl);
+
+		/* There was nothing to wait on, so return an already signaled fence. */
+
+		sync_fence_acc = mali_sync_timeline_create_signaled_fence(system->signaled_sync_tl);
+		if (NULL == sync_fence_acc) goto error;
+	}
+
+	/* Return file descriptor for the accumulated sync fence. */
+	return mali_sync_fence_fd_alloc(sync_fence_acc);
+
+error:
+	if (NULL != sync_fence_acc) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+		sync_fence_put(sync_fence_acc);
+#else
+		fput(sync_fence_acc->file);
+#endif
+	}
+
+	return -1;
+}
+
+void mali_timeline_sync_fence_activate(struct mali_timeline_sync_fence_tracker *sync_fence_tracker)
+{
+	mali_scheduler_mask schedule_mask = MALI_SCHEDULER_MASK_EMPTY;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_fence_tracker);
+	MALI_DEBUG_ASSERT_POINTER(sync_fence_tracker->flag);
+
+	MALI_DEBUG_PRINT(4, ("Mali Timeline: activation for sync fence tracker\n"));
+
+	/* Signal flag and release reference. */
+	mali_sync_flag_signal(sync_fence_tracker->flag, 0);
+	mali_sync_flag_put(sync_fence_tracker->flag);
+
+	/* Nothing can wait on this tracker, so nothing to schedule after release. */
+	schedule_mask = mali_timeline_tracker_release(&sync_fence_tracker->tracker);
+	MALI_DEBUG_ASSERT(MALI_SCHEDULER_MASK_EMPTY == schedule_mask);
+
+	_mali_osk_free(sync_fence_tracker);
+}
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_timeline_sync_fence.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_timeline_sync_fence.h
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2013, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_timeline_sync_fence.h
+ *
+ * This file contains code related to creating sync fences from timeline fences.
+ */
+
+#ifndef __MALI_TIMELINE_SYNC_FENCE_H__
+#define __MALI_TIMELINE_SYNC_FENCE_H__
+
+#include "mali_timeline.h"
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+
+/**
+ * Sync fence tracker.
+ */
+struct mali_timeline_sync_fence_tracker {
+	struct mali_sync_flag        *flag;    /**< Sync flag used to connect tracker and sync fence. */
+	struct mali_timeline_tracker  tracker; /**< Timeline tracker. */
+};
+
+/**
+ * Create a sync fence that will be signaled when @ref fence is signaled.
+ *
+ * @param system Timeline system.
+ * @param fence Fence to create sync fence from.
+ * @return File descriptor for new sync fence, or -1 on error.
+ */
+s32 mali_timeline_sync_fence_create(struct mali_timeline_system *system, struct mali_timeline_fence *fence);
+
+/**
+ * Used by the Timeline system to activate a sync fence tracker.
+ *
+ * @param sync_fence_tracker Sync fence tracker.
+ *
+ */
+void mali_timeline_sync_fence_activate(struct mali_timeline_sync_fence_tracker *sync_fence_tracker);
+
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+#endif /* __MALI_TIMELINE_SYNC_FENCE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_ukk.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_ukk.h
@@ -0,0 +1,551 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_ukk.h
+ * Defines the kernel-side interface of the user-kernel interface
+ */
+
+#ifndef __MALI_UKK_H__
+#define __MALI_UKK_H__
+
+#include "mali_osk.h"
+#include "mali_uk_types.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @addtogroup uddapi Unified Device Driver (UDD) APIs
+ *
+ * @{
+ */
+
+/**
+ * @addtogroup u_k_api UDD User/Kernel Interface (U/K) APIs
+ *
+ * - The _mali_uk functions are an abstraction of the interface to the device
+ * driver. On certain OSs, this would be implemented via the IOCTL interface.
+ * On other OSs, it could be via extension of some Device Driver Class, or
+ * direct function call for Bare metal/RTOSs.
+ * - It is important to note that:
+ *   -  The Device Driver has implemented the _mali_ukk set of functions
+ *   -  The Base Driver calls the corresponding set of _mali_uku functions.
+ * - What requires porting is solely the calling mechanism from User-side to
+ * Kernel-side, and propagating back the results.
+ * - Each U/K function is associated with a (group, number) pair from
+ * \ref _mali_uk_functions to make it possible for a common function in the
+ * Base Driver and Device Driver to route User/Kernel calls from/to the
+ * correct _mali_uk function. For example, in an IOCTL system, the IOCTL number
+ * would be formed based on the group and number assigned to the _mali_uk
+ * function, as listed in \ref _mali_uk_functions. On the user-side, each
+ * _mali_uku function would just make an IOCTL with the IOCTL-code being an
+ * encoded form of the (group, number) pair. On the kernel-side, the Device
+ * Driver's IOCTL handler decodes the IOCTL-code back into a (group, number)
+ * pair, and uses this to determine which corresponding _mali_ukk should be
+ * called.
+ *   - Refer to \ref _mali_uk_functions for more information about this
+ * (group, number) pairing.
+ * - In a system where there is no distinction between user and kernel-side,
+ * the U/K interface may be implemented as:@code
+ * MALI_STATIC_INLINE _mali_osk_errcode_t _mali_uku_examplefunction( _mali_uk_examplefunction_s *args )
+ * {
+ *     return mali_ukk_examplefunction( args );
+ * }
+ * @endcode
+ * - Therefore, all U/K calls behave \em as \em though they were direct
+ * function calls (but the \b implementation \em need \em not be a direct
+ * function calls)
+ *
+ * @note Naming the _mali_uk functions the same on both User and Kernel sides
+ * on non-RTOS systems causes debugging issues when setting breakpoints. In
+ * this case, it is not clear which function the breakpoint is put on.
+ * Therefore the _mali_uk functions in user space are prefixed with \c _mali_uku
+ * and in kernel space with \c _mali_ukk. The naming for the argument
+ * structures is unaffected.
+ *
+ * - The _mali_uk functions are synchronous.
+ * - Arguments to the _mali_uk functions are passed in a structure. The only
+ * parameter passed to the _mali_uk functions is a pointer to this structure.
+ * This first member of this structure, ctx, is a pointer to a context returned
+ * by _mali_uku_open(). For example:@code
+ * typedef struct
+ * {
+ *     void *ctx;
+ *     u32 number_of_cores;
+ * } _mali_uk_get_gp_number_of_cores_s;
+ * @endcode
+ *
+ * - Each _mali_uk function has its own argument structure named after the
+ *  function. The argument is distinguished by the _s suffix.
+ * - The argument types are defined by the base driver and user-kernel
+ *  interface.
+ * - All _mali_uk functions return a standard \ref _mali_osk_errcode_t.
+ * - Only arguments of type input or input/output need be initialized before
+ * calling a _mali_uk function.
+ * - Arguments of type output and input/output are only valid when the
+ * _mali_uk function returns \ref _MALI_OSK_ERR_OK.
+ * - The \c ctx member is always invalid after it has been used by a
+ * _mali_uk function, except for the context management functions
+ *
+ *
+ * \b Interface \b restrictions
+ *
+ * The requirements of the interface mean that an implementation of the
+ * User-kernel interface may do no 'real' work. For example, the following are
+ * illegal in the User-kernel implementation:
+ * - Calling functions necessary for operation on all systems,  which would
+ * not otherwise get called on RTOS systems.
+ *     - For example, a  U/K interface that calls multiple _mali_ukk functions
+ * during one particular U/K call. This could not be achieved by the same code
+ * which uses direct function calls for the U/K interface.
+ * -  Writing in values to the args members, when otherwise these members would
+ * not hold a useful value for a direct function call U/K interface.
+ *     - For example, U/K interface implementation that take NULL members in
+ * their arguments structure from the user side, but those members are
+ * replaced with non-NULL values in the kernel-side of the U/K interface
+ * implementation. A scratch area for writing data is one such example. In this
+ * case, a direct function call U/K interface would segfault, because no code
+ * would be present to replace the NULL pointer with a meaningful pointer.
+ *     - Note that we discourage the case where the U/K implementation changes
+ * a NULL argument member to non-NULL, and then the Device Driver code (outside
+ * of the U/K layer) re-checks this member for NULL, and corrects it when
+ * necessary. Whilst such code works even on direct function call U/K
+ * intefaces, it reduces the testing coverage of the Device Driver code. This
+ * is because we have no way of testing the NULL == value path on an OS
+ * implementation.
+ *
+ * A number of allowable examples exist where U/K interfaces do 'real' work:
+ * - The 'pointer switching' technique for \ref _mali_ukk_get_system_info
+ *     - In this case, without the pointer switching on direct function call
+ * U/K interface, the Device Driver code still sees the same thing: a pointer
+ * to which it can write memory. This is because such a system has no
+ * distinction between a user and kernel pointer.
+ * - Writing an OS-specific value into the ukk_private member for
+ * _mali_ukk_mem_mmap().
+ *     - In this case, this value is passed around by Device Driver code, but
+ * its actual value is never checked. Device Driver code simply passes it from
+ * the U/K layer to the OSK layer, where it can be acted upon. In this case,
+ * \em some OS implementations of the U/K (_mali_ukk_mem_mmap()) and OSK
+ * (_mali_osk_mem_mapregion_init()) functions will collaborate on the
+ *  meaning of ukk_private member. On other OSs, it may be unused by both
+ * U/K and OSK layers
+ *     - Therefore, on error inside the U/K interface implementation itself,
+ * it will be as though the _mali_ukk function itself had failed, and cleaned
+ * up after itself.
+ *     - Compare this to a direct function call U/K implementation, where all
+ * error cleanup is handled by the _mali_ukk function itself. The direct
+ * function call U/K interface implementation is automatically atomic.
+ *
+ * The last example highlights a consequence of all U/K interface
+ * implementations: they must be atomic with respect to the Device Driver code.
+ * And therefore, should Device Driver code succeed but the U/K implementation
+ * fail afterwards (but before return to user-space), then the U/K
+ * implementation must cause appropriate cleanup actions to preserve the
+ * atomicity of the interface.
+ *
+ * @{
+ */
+
+
+/** @defgroup _mali_uk_context U/K Context management
+ *
+ * These functions allow for initialisation of the user-kernel interface once per process.
+ *
+ * Generally the context will store the OS specific object to communicate with the kernel device driver and further
+ * state information required by the specific implementation. The context is shareable among all threads in the caller process.
+ *
+ * On IOCTL systems, this is likely to be a file descriptor as a result of opening the kernel device driver.
+ *
+ * On a bare-metal/RTOS system with no distinction between kernel and
+ * user-space, the U/K interface simply calls the _mali_ukk variant of the
+ * function by direct function call. In this case, the context returned is the
+ * mali_session_data from _mali_ukk_open().
+ *
+ * The kernel side implementations of the U/K interface expect the first member of the argument structure to
+ * be the context created by _mali_uku_open(). On some OS implementations, the meaning of this context
+ * will be different between user-side and kernel-side. In which case, the kernel-side will need to replace this context
+ * with the kernel-side equivalent, because user-side will not have access to kernel-side data. The context parameter
+ * in the argument structure therefore has to be of type input/output.
+ *
+ * It should be noted that the caller cannot reuse the \c ctx member of U/K
+ * argument structure after a U/K call, because it may be overwritten. Instead,
+ * the context handle must always be stored  elsewhere, and copied into
+ * the appropriate U/K argument structure for each user-side call to
+ * the U/K interface. This is not usually a problem, since U/K argument
+ * structures are usually placed on the stack.
+ *
+ * @{ */
+
+/** @brief Begin a new Mali Device Driver session
+ *
+ * This is used to obtain a per-process context handle for all future U/K calls.
+ *
+ * @param context pointer to storage to return a (void*)context handle.
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_open(void **context);
+
+/** @brief End a Mali Device Driver session
+ *
+ * This should be called when the process no longer requires use of the Mali Device Driver.
+ *
+ * The context handle must not be used after it has been closed.
+ *
+ * @param context pointer to a stored (void*)context handle.
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_close(void **context);
+
+/** @} */ /* end group _mali_uk_context */
+
+
+/** @addtogroup _mali_uk_core U/K Core
+ *
+ * The core functions provide the following functionality:
+ * - verify that the user and kernel API are compatible
+ * - retrieve information about the cores and memory banks in the system
+ * - wait for the result of jobs started on a core
+ *
+ * @{ */
+
+/** @brief Waits for a job notification.
+ *
+ * Sleeps until notified or a timeout occurs. Returns information about the notification.
+ *
+ * @param args see _mali_uk_wait_for_notification_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_wait_for_notification(_mali_uk_wait_for_notification_s *args);
+
+/** @brief Post a notification to the notification queue of this application.
+ *
+ * @param args see _mali_uk_post_notification_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_post_notification(_mali_uk_post_notification_s *args);
+
+/** @brief Verifies if the user and kernel side of this API are compatible.
+ *
+ * This function is obsolete, but kept to allow old, incompatible user space
+ * clients to robustly detect the incompatibility.
+ *
+ * @param args see _mali_uk_get_api_version_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_api_version(_mali_uk_get_api_version_s *args);
+
+/** @brief Verifies if the user and kernel side of this API are compatible.
+ *
+ * @param args see _mali_uk_get_api_version_v2_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_api_version_v2(_mali_uk_get_api_version_v2_s *args);
+
+/** @brief Get the user space settings applicable for calling process.
+ *
+ * @param args see _mali_uk_get_user_settings_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_user_settings(_mali_uk_get_user_settings_s *args);
+
+/** @brief Get a user space setting applicable for calling process.
+ *
+ * @param args see _mali_uk_get_user_setting_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_user_setting(_mali_uk_get_user_setting_s *args);
+
+/* @brief Grant or deny high priority scheduling for this session.
+ *
+ * @param args see _mali_uk_request_high_priority_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_request_high_priority(_mali_uk_request_high_priority_s *args);
+
+/** @brief Make process sleep if the pending big job in kernel  >= MALI_MAX_PENDING_BIG_JOB
+ *
+ */
+_mali_osk_errcode_t _mali_ukk_pending_submit(_mali_uk_pending_submit_s *args);
+
+/** @} */ /* end group _mali_uk_core */
+
+
+/** @addtogroup _mali_uk_memory U/K Memory
+ *
+ * The memory functions provide functionality with and without a Mali-MMU present.
+ *
+ * For Mali-MMU based systems, the following functionality is provided:
+ * - Initialize and terminate MALI virtual address space
+ * - Allocate/deallocate physical memory to a MALI virtual address range and map into/unmap from the
+ * current process address space
+ * - Map/unmap external physical memory into the MALI virtual address range
+ *
+ * For Mali-nonMMU based systems:
+ * - Allocate/deallocate MALI memory
+ *
+ * @{ */
+
+/** @brief Map Mali Memory into the current user process
+ *
+ * Maps Mali memory into the current user process in a generic way.
+ *
+ * This function is to be used for Mali-MMU mode. The function is available in both Mali-MMU and Mali-nonMMU modes,
+ * but should not be called by a user process in Mali-nonMMU mode.
+ *
+ * The implementation and operation of _mali_ukk_mem_mmap() is dependant on whether the driver is built for Mali-MMU
+ * or Mali-nonMMU:
+ * - In the nonMMU case, _mali_ukk_mem_mmap() requires a physical address to be specified. For this reason, an OS U/K
+ * implementation should not allow this to be called from user-space. In any case, nonMMU implementations are
+ * inherently insecure, and so the overall impact is minimal. Mali-MMU mode should be used if security is desired.
+ * - In the MMU case, _mali_ukk_mem_mmap() the _mali_uk_mem_mmap_s::phys_addr
+ * member is used for the \em Mali-virtual address desired for the mapping. The
+ * implementation of _mali_ukk_mem_mmap() will allocate both the CPU-virtual
+ * and CPU-physical addresses, and can cope with mapping a contiguous virtual
+ * address range to a sequence of non-contiguous physical pages. In this case,
+ * the CPU-physical addresses are not communicated back to the user-side, as
+ * they are unnecsessary; the \em Mali-virtual address range must be used for
+ * programming Mali structures.
+ *
+ * In the second (MMU) case, _mali_ukk_mem_mmap() handles management of
+ * CPU-virtual and CPU-physical ranges, but the \em caller must manage the
+ * \em Mali-virtual address range from the user-side.
+ *
+ * @note Mali-virtual address ranges are entirely separate between processes.
+ * It is not possible for a process to accidentally corrupt another process'
+ * \em Mali-virtual address space.
+ *
+ * @param args see _mali_uk_mem_mmap_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_mem_mmap(_mali_uk_mem_mmap_s *args);
+
+/** @brief Unmap Mali Memory from the current user process
+ *
+ * Unmaps Mali memory from the current user process in a generic way. This only operates on Mali memory supplied
+ * from _mali_ukk_mem_mmap().
+ *
+ * @param args see _mali_uk_mem_munmap_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_mem_munmap(_mali_uk_mem_munmap_s *args);
+
+/** @brief Determine the buffer size necessary for an MMU page table dump.
+ * @param args see _mali_uk_query_mmu_page_table_dump_size_s in mali_utgard_uk_types.h
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_query_mmu_page_table_dump_size(_mali_uk_query_mmu_page_table_dump_size_s *args);
+/** @brief Dump MMU Page tables.
+ * @param args see _mali_uk_dump_mmu_page_table_s in mali_utgard_uk_types.h
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_dump_mmu_page_table(_mali_uk_dump_mmu_page_table_s *args);
+
+/** @brief Write user data to specified Mali memory without causing segfaults.
+ * @param args see _mali_uk_mem_write_safe_s in mali_utgard_uk_types.h
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_mem_write_safe(_mali_uk_mem_write_safe_s *args);
+
+/** @} */ /* end group _mali_uk_memory */
+
+
+/** @addtogroup _mali_uk_pp U/K Fragment Processor
+ *
+ * The Fragment Processor (aka PP (Pixel Processor)) functions provide the following functionality:
+ * - retrieving version of the fragment processors
+ * - determine number of fragment processors
+ * - starting a job on a fragment processor
+ *
+ * @{ */
+
+/** @brief Issue a request to start a new job on a Fragment Processor.
+ *
+ * If the request fails args->status is set to _MALI_UK_START_JOB_NOT_STARTED_DO_REQUEUE and you can
+ * try to start the job again.
+ *
+ * An existing job could be returned for requeueing if the new job has a higher priority than a previously started job
+ * which the hardware hasn't actually started processing yet. In this case the new job will be started instead and the
+ * existing one returned, otherwise the new job is started and the status field args->status is set to
+ * _MALI_UK_START_JOB_STARTED.
+ *
+ * Job completion can be awaited with _mali_ukk_wait_for_notification().
+ *
+ * @param ctx user-kernel context (mali_session)
+ * @param uargs see _mali_uk_pp_start_job_s in "mali_utgard_uk_types.h". Use _mali_osk_copy_from_user to retrieve data!
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_pp_start_job(void *ctx, _mali_uk_pp_start_job_s *uargs);
+
+/**
+ * @brief Issue a request to start new jobs on both Vertex Processor and Fragment Processor.
+ *
+ * @note Will call into @ref _mali_ukk_pp_start_job and @ref _mali_ukk_gp_start_job.
+ *
+ * @param ctx user-kernel context (mali_session)
+ * @param uargs see _mali_uk_pp_and_gp_start_job_s in "mali_utgard_uk_types.h". Use _mali_osk_copy_from_user to retrieve data!
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_pp_and_gp_start_job(void *ctx, _mali_uk_pp_and_gp_start_job_s *uargs);
+
+/** @brief Returns the number of Fragment Processors in the system
+ *
+ * @param args see _mali_uk_get_pp_number_of_cores_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_pp_number_of_cores(_mali_uk_get_pp_number_of_cores_s *args);
+
+/** @brief Returns the version that all Fragment Processor cores are compatible with.
+ *
+ * This function may only be called when _mali_ukk_get_pp_number_of_cores() indicated at least one Fragment
+ * Processor core is available.
+ *
+ * @param args see _mali_uk_get_pp_core_version_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_pp_core_version(_mali_uk_get_pp_core_version_s *args);
+
+/** @brief Disable Write-back unit(s) on specified job
+ *
+ * @param args see _mali_uk_get_pp_core_version_s in "mali_utgard_uk_types.h"
+ */
+void _mali_ukk_pp_job_disable_wb(_mali_uk_pp_disable_wb_s *args);
+
+
+/** @} */ /* end group _mali_uk_pp */
+
+
+/** @addtogroup _mali_uk_gp U/K Vertex Processor
+ *
+ * The Vertex Processor (aka GP (Geometry Processor)) functions provide the following functionality:
+ * - retrieving version of the Vertex Processors
+ * - determine number of Vertex Processors available
+ * - starting a job on a Vertex Processor
+ *
+ * @{ */
+
+/** @brief Issue a request to start a new job on a Vertex Processor.
+ *
+ * If the request fails args->status is set to _MALI_UK_START_JOB_NOT_STARTED_DO_REQUEUE and you can
+ * try to start the job again.
+ *
+ * An existing job could be returned for requeueing if the new job has a higher priority than a previously started job
+ * which the hardware hasn't actually started processing yet. In this case the new job will be started and the
+ * existing one returned, otherwise the new job is started and the status field args->status is set to
+ * _MALI_UK_START_JOB_STARTED.
+ *
+ * Job completion can be awaited with _mali_ukk_wait_for_notification().
+ *
+ * @param ctx user-kernel context (mali_session)
+ * @param uargs see _mali_uk_gp_start_job_s in "mali_utgard_uk_types.h". Use _mali_osk_copy_from_user to retrieve data!
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_gp_start_job(void *ctx, _mali_uk_gp_start_job_s *uargs);
+
+/** @brief Returns the number of Vertex Processors in the system.
+ *
+ * @param args see _mali_uk_get_gp_number_of_cores_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_gp_number_of_cores(_mali_uk_get_gp_number_of_cores_s *args);
+
+/** @brief Returns the version that all Vertex Processor cores are compatible with.
+ *
+ * This function may only be called when _mali_uk_get_gp_number_of_cores() indicated at least one Vertex
+ * Processor core is available.
+ *
+ * @param args see _mali_uk_get_gp_core_version_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_get_gp_core_version(_mali_uk_get_gp_core_version_s *args);
+
+/** @brief Resume or abort suspended Vertex Processor jobs.
+ *
+ * After receiving notification that a Vertex Processor job was suspended from
+ * _mali_ukk_wait_for_notification() you can use this function to resume or abort the job.
+ *
+ * @param args see _mali_uk_gp_suspend_response_s in "mali_utgard_uk_types.h"
+ * @return _MALI_OSK_ERR_OK on success, otherwise a suitable _mali_osk_errcode_t on failure.
+ */
+_mali_osk_errcode_t _mali_ukk_gp_suspend_response(_mali_uk_gp_suspend_response_s *args);
+
+/** @} */ /* end group _mali_uk_gp */
+
+#if defined(CONFIG_MALI400_PROFILING)
+/** @addtogroup _mali_uk_profiling U/K Timeline profiling module
+ * @{ */
+
+/** @brief Add event to profiling buffer.
+ *
+ * @param args see _mali_uk_profiling_add_event_s in "mali_utgard_uk_types.h"
+ */
+_mali_osk_errcode_t _mali_ukk_profiling_add_event(_mali_uk_profiling_add_event_s *args);
+
+/** @brief Get profiling stream fd.
+ *
+ * @param args see _mali_uk_profiling_stream_fd_get_s in "mali_utgard_uk_types.h"
+ */
+_mali_osk_errcode_t _mali_ukk_profiling_stream_fd_get(_mali_uk_profiling_stream_fd_get_s *args);
+
+/** @brief Profiling control set.
+ *
+ * @param args see _mali_uk_profiling_control_set_s in "mali_utgard_uk_types.h"
+ */
+_mali_osk_errcode_t _mali_ukk_profiling_control_set(_mali_uk_profiling_control_set_s *args);
+
+/** @} */ /* end group _mali_uk_profiling */
+#endif
+
+/** @addtogroup _mali_uk_vsync U/K VSYNC reporting module
+ * @{ */
+
+/** @brief Report events related to vsync.
+ *
+ * @note Events should be reported when starting to wait for vsync and when the
+ * waiting is finished. This information can then be used in kernel space to
+ * complement the GPU utilization metric.
+ *
+ * @param args see _mali_uk_vsync_event_report_s in "mali_utgard_uk_types.h"
+ */
+_mali_osk_errcode_t _mali_ukk_vsync_event_report(_mali_uk_vsync_event_report_s *args);
+
+/** @} */ /* end group _mali_uk_vsync */
+
+/** @addtogroup _mali_sw_counters_report U/K Software counter reporting
+ * @{ */
+
+/** @brief Report software counters.
+ *
+ * @param args see _mali_uk_sw_counters_report_s in "mali_uk_types.h"
+ */
+_mali_osk_errcode_t _mali_ukk_sw_counters_report(_mali_uk_sw_counters_report_s *args);
+
+/** @} */ /* end group _mali_sw_counters_report */
+
+/** @} */ /* end group u_k_api */
+
+/** @} */ /* end group uddapi */
+
+u32 _mali_ukk_report_memory_usage(void);
+
+u32 _mali_ukk_report_total_memory_size(void);
+
+u32 _mali_ukk_utilization_gp_pp(void);
+
+u32 _mali_ukk_utilization_gp(void);
+
+u32 _mali_ukk_utilization_pp(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_UKK_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_user_settings_db.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_user_settings_db.c
@@ -0,0 +1,147 @@
+/**
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_ukk.h"
+#include "mali_uk_types.h"
+#include "mali_user_settings_db.h"
+#include "mali_session.h"
+
+static u32 mali_user_settings[_MALI_UK_USER_SETTING_MAX];
+const char *_mali_uk_user_setting_descriptions[] = _MALI_UK_USER_SETTING_DESCRIPTIONS;
+
+static void mali_user_settings_notify(_mali_uk_user_setting_t setting, u32 value)
+{
+	mali_bool done = MALI_FALSE;
+
+	/*
+	 * This function gets a bit complicated because we can't hold the session lock while
+	 * allocating notification objects.
+	 */
+
+	while (!done) {
+		u32 i;
+		u32 num_sessions_alloc;
+		u32 num_sessions_with_lock;
+		u32 used_notification_objects = 0;
+		_mali_osk_notification_t **notobjs;
+
+		/* Pre allocate the number of notifications objects we need right now (might change after lock has been taken) */
+		num_sessions_alloc = mali_session_get_count();
+		if (0 == num_sessions_alloc) {
+			/* No sessions to report to */
+			return;
+		}
+
+		notobjs = (_mali_osk_notification_t **)_mali_osk_malloc(sizeof(_mali_osk_notification_t *) * num_sessions_alloc);
+		if (NULL == notobjs) {
+			MALI_PRINT_ERROR(("Failed to notify user space session about num PP core change (alloc failure)\n"));
+			return;
+		}
+
+		for (i = 0; i < num_sessions_alloc; i++) {
+			notobjs[i] = _mali_osk_notification_create(_MALI_NOTIFICATION_SETTINGS_CHANGED,
+					sizeof(_mali_uk_settings_changed_s));
+			if (NULL != notobjs[i]) {
+				_mali_uk_settings_changed_s *data;
+				data = notobjs[i]->result_buffer;
+
+				data->setting = setting;
+				data->value = value;
+			} else {
+				MALI_PRINT_ERROR(("Failed to notify user space session about setting change (alloc failure %u)\n", i));
+			}
+		}
+
+		mali_session_lock();
+
+		/* number of sessions will not change while we hold the lock */
+		num_sessions_with_lock = mali_session_get_count();
+
+		if (num_sessions_alloc >= num_sessions_with_lock) {
+			/* We have allocated enough notification objects for all the sessions atm */
+			struct mali_session_data *session, *tmp;
+			MALI_SESSION_FOREACH(session, tmp, link) {
+				MALI_DEBUG_ASSERT(used_notification_objects < num_sessions_alloc);
+				if (NULL != notobjs[used_notification_objects]) {
+					mali_session_send_notification(session, notobjs[used_notification_objects]);
+					notobjs[used_notification_objects] = NULL; /* Don't track this notification object any more */
+				}
+				used_notification_objects++;
+			}
+			done = MALI_TRUE;
+		}
+
+		mali_session_unlock();
+
+		/* Delete any remaining/unused notification objects */
+		for (; used_notification_objects < num_sessions_alloc; used_notification_objects++) {
+			if (NULL != notobjs[used_notification_objects]) {
+				_mali_osk_notification_delete(notobjs[used_notification_objects]);
+			}
+		}
+
+		_mali_osk_free(notobjs);
+	}
+}
+
+void mali_set_user_setting(_mali_uk_user_setting_t setting, u32 value)
+{
+	mali_bool notify = MALI_FALSE;
+
+	if (setting >= _MALI_UK_USER_SETTING_MAX) {
+		MALI_DEBUG_PRINT_ERROR(("Invalid user setting %ud\n"));
+		return;
+	}
+
+	if (mali_user_settings[setting] != value) {
+		notify = MALI_TRUE;
+	}
+
+	mali_user_settings[setting] = value;
+
+	if (notify) {
+		mali_user_settings_notify(setting, value);
+	}
+}
+
+u32 mali_get_user_setting(_mali_uk_user_setting_t setting)
+{
+	if (setting >= _MALI_UK_USER_SETTING_MAX) {
+		return 0;
+	}
+
+	return mali_user_settings[setting];
+}
+
+_mali_osk_errcode_t _mali_ukk_get_user_setting(_mali_uk_get_user_setting_s *args)
+{
+	_mali_uk_user_setting_t setting;
+	MALI_DEBUG_ASSERT_POINTER(args);
+
+	setting = args->setting;
+
+	if (_MALI_UK_USER_SETTING_MAX > setting) {
+		args->value = mali_user_settings[setting];
+		return _MALI_OSK_ERR_OK;
+	} else {
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	}
+}
+
+_mali_osk_errcode_t _mali_ukk_get_user_settings(_mali_uk_get_user_settings_s *args)
+{
+	MALI_DEBUG_ASSERT_POINTER(args);
+
+	_mali_osk_memcpy(args->settings, mali_user_settings, sizeof(mali_user_settings));
+
+	return _MALI_OSK_ERR_OK;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/common/mali_user_settings_db.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/common/mali_user_settings_db.h
@@ -0,0 +1,39 @@
+/**
+ * Copyright (C) 2012-2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_USER_SETTINGS_DB_H__
+#define __MALI_USER_SETTINGS_DB_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "mali_uk_types.h"
+
+/** @brief Set Mali user setting in DB
+ *
+ * Update the DB with a new value for \a setting. If the value is different from theprevious set value running sessions will be notified of the change.
+ *
+ * @param setting the setting to be changed
+ * @param value the new value to set
+ */
+void mali_set_user_setting(_mali_uk_user_setting_t setting, u32 value);
+
+/** @brief Get current Mali user setting value from DB
+ *
+ * @param setting the setting to extract
+ * @return the value of the selected setting
+ */
+u32 mali_get_user_setting(_mali_uk_user_setting_t setting);
+
+#ifdef __cplusplus
+}
+#endif
+#endif  /* __MALI_KERNEL_USER_SETTING__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/include/linux/mali/mali_utgard.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/include/linux/mali/mali_utgard.h
@@ -0,0 +1,526 @@
+/*
+ * Copyright (C) 2012-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_utgard.h
+ * Defines types and interface exposed by the Mali Utgard device driver
+ */
+
+#ifndef __MALI_UTGARD_H__
+#define __MALI_UTGARD_H__
+
+#include "mali_osk_types.h"
+#ifdef CONFIG_MALI_DEVFREQ
+#include <linux/devfreq.h>
+#include "mali_pm_metrics.h"
+#ifdef CONFIG_DEVFREQ_THERMAL
+#include <linux/devfreq_cooling.h>
+#endif
+#endif
+
+#define MALI_GPU_NAME_UTGARD "mali-utgard"
+
+
+#define MALI_OFFSET_GP                    0x00000
+#define MALI_OFFSET_GP_MMU                0x03000
+
+#define MALI_OFFSET_PP0                   0x08000
+#define MALI_OFFSET_PP0_MMU               0x04000
+#define MALI_OFFSET_PP1                   0x0A000
+#define MALI_OFFSET_PP1_MMU               0x05000
+#define MALI_OFFSET_PP2                   0x0C000
+#define MALI_OFFSET_PP2_MMU               0x06000
+#define MALI_OFFSET_PP3                   0x0E000
+#define MALI_OFFSET_PP3_MMU               0x07000
+
+#define MALI_OFFSET_PP4                   0x28000
+#define MALI_OFFSET_PP4_MMU               0x1C000
+#define MALI_OFFSET_PP5                   0x2A000
+#define MALI_OFFSET_PP5_MMU               0x1D000
+#define MALI_OFFSET_PP6                   0x2C000
+#define MALI_OFFSET_PP6_MMU               0x1E000
+#define MALI_OFFSET_PP7                   0x2E000
+#define MALI_OFFSET_PP7_MMU               0x1F000
+
+#define MALI_OFFSET_L2_RESOURCE0          0x01000
+#define MALI_OFFSET_L2_RESOURCE1          0x10000
+#define MALI_OFFSET_L2_RESOURCE2          0x11000
+
+#define MALI400_OFFSET_L2_CACHE0          MALI_OFFSET_L2_RESOURCE0
+#define MALI450_OFFSET_L2_CACHE0          MALI_OFFSET_L2_RESOURCE1
+#define MALI450_OFFSET_L2_CACHE1          MALI_OFFSET_L2_RESOURCE0
+#define MALI450_OFFSET_L2_CACHE2          MALI_OFFSET_L2_RESOURCE2
+#define MALI470_OFFSET_L2_CACHE1          MALI_OFFSET_L2_RESOURCE0
+
+#define MALI_OFFSET_BCAST                 0x13000
+#define MALI_OFFSET_DLBU                  0x14000
+
+#define MALI_OFFSET_PP_BCAST              0x16000
+#define MALI_OFFSET_PP_BCAST_MMU          0x15000
+
+#define MALI_OFFSET_PMU                   0x02000
+#define MALI_OFFSET_DMA                   0x12000
+
+/* Mali-300 */
+
+#define MALI_GPU_RESOURCES_MALI300(base_addr, gp_irq, gp_mmu_irq, pp_irq, pp_mmu_irq) \
+	MALI_GPU_RESOURCES_MALI400_MP1(base_addr, gp_irq, gp_mmu_irq, pp_irq, pp_mmu_irq)
+
+#define MALI_GPU_RESOURCES_MALI300_PMU(base_addr, gp_irq, gp_mmu_irq, pp_irq, pp_mmu_irq) \
+	MALI_GPU_RESOURCES_MALI400_MP1_PMU(base_addr, gp_irq, gp_mmu_irq, pp_irq, pp_mmu_irq)
+
+/* Mali-400 */
+
+#define MALI_GPU_RESOURCES_MALI400_MP1(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI400_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq)
+
+#define MALI_GPU_RESOURCES_MALI400_MP1_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq) \
+	MALI_GPU_RESOURCES_MALI400_MP1(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU)
+
+#define MALI_GPU_RESOURCES_MALI400_MP2(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI400_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq)
+
+#define MALI_GPU_RESOURCES_MALI400_MP2_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq) \
+	MALI_GPU_RESOURCES_MALI400_MP2(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU)
+
+#define MALI_GPU_RESOURCES_MALI400_MP3(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI400_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq)
+
+#define MALI_GPU_RESOURCES_MALI400_MP3_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq) \
+	MALI_GPU_RESOURCES_MALI400_MP3(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU)
+
+#define MALI_GPU_RESOURCES_MALI400_MP4(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI400_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(3, base_addr + MALI_OFFSET_PP3, pp3_irq, base_addr + MALI_OFFSET_PP3_MMU, pp3_mmu_irq)
+
+#define MALI_GPU_RESOURCES_MALI400_MP4_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq) \
+	MALI_GPU_RESOURCES_MALI400_MP4(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+	/* Mali-450 */
+#define MALI_GPU_RESOURCES_MALI450_MP2(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU) \
+	MALI_GPU_RESOURCE_DMA(base_addr + MALI_OFFSET_DMA)
+
+#define MALI_GPU_RESOURCES_MALI450_MP2_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI450_MP2(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI450_MP3(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU)
+
+#define MALI_GPU_RESOURCES_MALI450_MP3_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI450_MP3(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI450_MP4(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(3, base_addr + MALI_OFFSET_PP3, pp3_irq, base_addr + MALI_OFFSET_PP3_MMU, pp3_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU) \
+	MALI_GPU_RESOURCE_DMA(base_addr + MALI_OFFSET_DMA)
+
+#define MALI_GPU_RESOURCES_MALI450_MP4_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI450_MP4(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI450_MP6(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp4_irq, pp4_mmu_irq, pp5_irq, pp5_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE2) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(3, base_addr + MALI_OFFSET_PP4, pp3_irq, base_addr + MALI_OFFSET_PP4_MMU, pp3_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(4, base_addr + MALI_OFFSET_PP5, pp4_irq, base_addr + MALI_OFFSET_PP5_MMU, pp4_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(5, base_addr + MALI_OFFSET_PP6, pp5_irq, base_addr + MALI_OFFSET_PP6_MMU, pp5_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU) \
+	MALI_GPU_RESOURCE_DMA(base_addr + MALI_OFFSET_DMA)
+
+#define MALI_GPU_RESOURCES_MALI450_MP6_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp4_irq, pp4_mmu_irq, pp5_irq, pp5_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI450_MP6(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp4_irq, pp4_mmu_irq, pp5_irq, pp5_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI450_MP8(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp4_irq, pp4_mmu_irq, pp5_irq, pp5_mmu_irq, pp6_irq, pp6_mmu_irq, pp7_irq, pp7_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE0) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(3, base_addr + MALI_OFFSET_PP3, pp3_irq, base_addr + MALI_OFFSET_PP3_MMU, pp3_mmu_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI450_OFFSET_L2_CACHE2) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(4, base_addr + MALI_OFFSET_PP4, pp4_irq, base_addr + MALI_OFFSET_PP4_MMU, pp4_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(5, base_addr + MALI_OFFSET_PP5, pp5_irq, base_addr + MALI_OFFSET_PP5_MMU, pp5_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(6, base_addr + MALI_OFFSET_PP6, pp6_irq, base_addr + MALI_OFFSET_PP6_MMU, pp6_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(7, base_addr + MALI_OFFSET_PP7, pp7_irq, base_addr + MALI_OFFSET_PP7_MMU, pp7_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU) \
+	MALI_GPU_RESOURCE_DMA(base_addr + MALI_OFFSET_DMA)
+
+#define MALI_GPU_RESOURCES_MALI450_MP8_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp4_irq, pp4_mmu_irq, pp5_irq, pp5_mmu_irq, pp6_irq, pp6_mmu_irq, pp7_irq, pp7_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI450_MP8(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp4_irq, pp4_mmu_irq, pp5_irq, pp5_mmu_irq, pp6_irq, pp6_mmu_irq, pp7_irq, pp7_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+	/* Mali - 470 */
+#define MALI_GPU_RESOURCES_MALI470_MP1(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI470_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU)
+
+#define MALI_GPU_RESOURCES_MALI470_MP1_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI470_MP1(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI470_MP2(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI470_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU)
+
+#define MALI_GPU_RESOURCES_MALI470_MP2_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI470_MP2(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI470_MP3(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI470_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU)
+
+#define MALI_GPU_RESOURCES_MALI470_MP3_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI470_MP3(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCES_MALI470_MP4(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_L2(base_addr + MALI470_OFFSET_L2_CACHE1) \
+	MALI_GPU_RESOURCE_GP_WITH_MMU(base_addr + MALI_OFFSET_GP, gp_irq, base_addr + MALI_OFFSET_GP_MMU, gp_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(0, base_addr + MALI_OFFSET_PP0, pp0_irq, base_addr + MALI_OFFSET_PP0_MMU, pp0_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(1, base_addr + MALI_OFFSET_PP1, pp1_irq, base_addr + MALI_OFFSET_PP1_MMU, pp1_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(2, base_addr + MALI_OFFSET_PP2, pp2_irq, base_addr + MALI_OFFSET_PP2_MMU, pp2_mmu_irq) \
+	MALI_GPU_RESOURCE_PP_WITH_MMU(3, base_addr + MALI_OFFSET_PP3, pp3_irq, base_addr + MALI_OFFSET_PP3_MMU, pp3_mmu_irq) \
+	MALI_GPU_RESOURCE_BCAST(base_addr + MALI_OFFSET_BCAST) \
+	MALI_GPU_RESOURCE_DLBU(base_addr + MALI_OFFSET_DLBU) \
+	MALI_GPU_RESOURCE_PP_BCAST(base_addr + MALI_OFFSET_PP_BCAST, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PP_MMU_BCAST(base_addr + MALI_OFFSET_PP_BCAST_MMU)
+
+#define MALI_GPU_RESOURCES_MALI470_MP4_PMU(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCES_MALI470_MP4(base_addr, gp_irq, gp_mmu_irq, pp0_irq, pp0_mmu_irq, pp1_irq, pp1_mmu_irq, pp2_irq, pp2_mmu_irq, pp3_irq, pp3_mmu_irq, pp_bcast_irq) \
+	MALI_GPU_RESOURCE_PMU(base_addr + MALI_OFFSET_PMU) \
+
+#define MALI_GPU_RESOURCE_L2(addr) \
+	{ \
+		.name = "Mali_L2", \
+			.flags = IORESOURCE_MEM, \
+				 .start = addr, \
+					  .end   = addr + 0x200, \
+	},
+
+#define MALI_GPU_RESOURCE_GP(gp_addr, gp_irq) \
+	{ \
+		.name = "Mali_GP", \
+			.flags = IORESOURCE_MEM, \
+				 .start = gp_addr, \
+					  .end =   gp_addr + 0x100, \
+	}, \
+	{ \
+		.name = "Mali_GP_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = gp_irq, \
+					  .end   = gp_irq, \
+	}, \
+
+#define MALI_GPU_RESOURCE_GP_WITH_MMU(gp_addr, gp_irq, gp_mmu_addr, gp_mmu_irq) \
+	{ \
+		.name = "Mali_GP", \
+			.flags = IORESOURCE_MEM, \
+				 .start = gp_addr, \
+					  .end =   gp_addr + 0x100, \
+	}, \
+	{ \
+		.name = "Mali_GP_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = gp_irq, \
+					  .end   = gp_irq, \
+	}, \
+	{ \
+		.name = "Mali_GP_MMU", \
+			.flags = IORESOURCE_MEM, \
+				 .start = gp_mmu_addr, \
+					  .end =   gp_mmu_addr + 0x100, \
+	}, \
+	{ \
+		.name = "Mali_GP_MMU_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = gp_mmu_irq, \
+					  .end =   gp_mmu_irq, \
+	},
+
+#define MALI_GPU_RESOURCE_PP(pp_addr, pp_irq) \
+	{ \
+		.name = "Mali_PP", \
+			.flags = IORESOURCE_MEM, \
+				 .start = pp_addr, \
+					  .end =   pp_addr + 0x1100, \
+	}, \
+	{ \
+		.name = "Mali_PP_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = pp_irq, \
+					  .end =   pp_irq, \
+	}, \
+
+#define MALI_GPU_RESOURCE_PP_WITH_MMU(id, pp_addr, pp_irq, pp_mmu_addr, pp_mmu_irq) \
+	{ \
+		.name = "Mali_PP" #id, \
+			.flags = IORESOURCE_MEM, \
+				 .start = pp_addr, \
+					  .end =   pp_addr + 0x1100, \
+	}, \
+	{ \
+		.name = "Mali_PP" #id "_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = pp_irq, \
+					  .end =   pp_irq, \
+	}, \
+	{ \
+		.name = "Mali_PP" #id "_MMU", \
+			.flags = IORESOURCE_MEM, \
+				 .start = pp_mmu_addr, \
+					  .end =   pp_mmu_addr + 0x100, \
+	}, \
+	{ \
+		.name = "Mali_PP" #id "_MMU_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = pp_mmu_irq, \
+					  .end =   pp_mmu_irq, \
+	},
+
+#define MALI_GPU_RESOURCE_MMU(mmu_addr, mmu_irq) \
+	{ \
+		.name = "Mali_MMU", \
+			.flags = IORESOURCE_MEM, \
+				 .start = mmu_addr, \
+					  .end =   mmu_addr + 0x100, \
+	}, \
+	{ \
+		.name = "Mali_MMU_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = mmu_irq, \
+					  .end =   mmu_irq, \
+	},
+
+#define MALI_GPU_RESOURCE_PMU(pmu_addr) \
+	{ \
+		.name = "Mali_PMU", \
+			.flags = IORESOURCE_MEM, \
+				 .start = pmu_addr, \
+					  .end =   pmu_addr + 0x100, \
+	},
+
+#define MALI_GPU_RESOURCE_DMA(dma_addr) \
+	{ \
+		.name = "Mali_DMA", \
+			.flags = IORESOURCE_MEM, \
+				 .start = dma_addr, \
+					  .end = dma_addr + 0x100, \
+	},
+
+#define MALI_GPU_RESOURCE_DLBU(dlbu_addr) \
+	{ \
+		.name = "Mali_DLBU", \
+			.flags = IORESOURCE_MEM, \
+				 .start = dlbu_addr, \
+					  .end = dlbu_addr + 0x100, \
+	},
+
+#define MALI_GPU_RESOURCE_BCAST(bcast_addr) \
+	{ \
+		.name = "Mali_Broadcast", \
+			.flags = IORESOURCE_MEM, \
+				 .start = bcast_addr, \
+					  .end = bcast_addr + 0x100, \
+	},
+
+#define MALI_GPU_RESOURCE_PP_BCAST(pp_addr, pp_irq) \
+	{ \
+		.name = "Mali_PP_Broadcast", \
+			.flags = IORESOURCE_MEM, \
+				 .start = pp_addr, \
+					  .end =   pp_addr + 0x1100, \
+	}, \
+	{ \
+		.name = "Mali_PP_Broadcast_IRQ", \
+			.flags = IORESOURCE_IRQ, \
+				 .start = pp_irq, \
+					  .end =   pp_irq, \
+	}, \
+
+#define MALI_GPU_RESOURCE_PP_MMU_BCAST(pp_mmu_bcast_addr) \
+	{ \
+		.name = "Mali_PP_MMU_Broadcast", \
+			.flags = IORESOURCE_MEM, \
+				 .start = pp_mmu_bcast_addr, \
+					  .end = pp_mmu_bcast_addr + 0x100, \
+	},
+
+	struct mali_gpu_utilization_data {
+		unsigned int utilization_gpu; /* Utilization for GP and all PP cores combined, 0 = no utilization, 256 = full utilization */
+		unsigned int utilization_gp;  /* Utilization for GP core only, 0 = no utilization, 256 = full utilization */
+		unsigned int utilization_pp;  /* Utilization for all PP cores combined, 0 = no utilization, 256 = full utilization */
+	};
+
+	struct mali_gpu_clk_item {
+		unsigned int clock; /* unit(MHz) */
+		unsigned int vol;
+	};
+
+	struct mali_gpu_clock {
+		struct mali_gpu_clk_item *item;
+		unsigned int num_of_steps;
+	};
+
+	struct mali_gpu_device_data {
+		/* Shared GPU memory */
+		unsigned long shared_mem_size;
+
+		/*
+		 * Mali PMU switch delay.
+		 * Only needed if the power gates are connected to the PMU in a high fanout
+		 * network. This value is the number of Mali clock cycles it takes to
+		 * enable the power gates and turn on the power mesh.
+		 * This value will have no effect if a daisy chain implementation is used.
+		 */
+		u32 pmu_switch_delay;
+
+		/* Mali Dynamic power domain configuration in sequence from 0-11
+		 *  GP  PP0 PP1  PP2  PP3  PP4  PP5  PP6  PP7, L2$0 L2$1 L2$2
+		 */
+		u16 pmu_domain_config[12];
+
+		/* Dedicated GPU memory range (physical). */
+		unsigned long dedicated_mem_start;
+		unsigned long dedicated_mem_size;
+
+		/* Frame buffer memory to be accessible by Mali GPU (physical) */
+		unsigned long fb_start;
+		unsigned long fb_size;
+
+		/* Max runtime [ms] for jobs */
+		int max_job_runtime;
+
+		/* Report GPU utilization and related control in this interval (specified in ms) */
+		unsigned long control_interval;
+
+		/* Function that will receive periodic GPU utilization numbers */
+		void (*utilization_callback)(struct mali_gpu_utilization_data *data);
+
+		/* Fuction that platform callback for freq setting, needed when CONFIG_MALI_DVFS enabled */
+		int (*set_freq)(int setting_clock_step);
+		/* Function that platfrom report it's clock info which driver can set, needed when CONFIG_MALI_DVFS enabled */
+		void (*get_clock_info)(struct mali_gpu_clock **data);
+		/* Function that get the current clock info, needed when CONFIG_MALI_DVFS enabled */
+		int (*get_freq)(void);
+		/* Function that init the mali gpu secure mode */
+		int (*secure_mode_init)(void);
+		/* Function that deinit the mali gpu secure mode */
+		void (*secure_mode_deinit)(void);
+		/* Function that reset GPU and enable gpu secure mode */
+		int (*gpu_reset_and_secure_mode_enable)(void);
+		/* Function that Reset GPU and disable gpu secure mode */
+		int (*gpu_reset_and_secure_mode_disable)(void);
+		/* ipa related interface customer need register */
+#if defined(CONFIG_MALI_DEVFREQ) && defined(CONFIG_DEVFREQ_THERMAL)
+		struct devfreq_cooling_power *gpu_cooling_ops;
+#endif
+	};
+
+	/**
+	 * Pause the scheduling and power state changes of Mali device driver.
+	 * mali_dev_resume() must always be called as soon as possible after this function
+	 * in order to resume normal operation of the Mali driver.
+	 */
+	void mali_dev_pause(void);
+
+	/**
+	 * Resume scheduling and allow power changes in Mali device driver.
+	 * This must always be called after mali_dev_pause().
+	 */
+	void mali_dev_resume(void);
+
+	/** @brief Set the desired number of PP cores to use.
+	 *
+	 * The internal Mali PMU will be used, if present, to physically power off the PP cores.
+	 *
+	 * @param num_cores The number of desired cores
+	 * @return 0 on success, otherwise error. -EINVAL means an invalid number of cores was specified.
+	 */
+	int mali_perf_set_num_pp_cores(unsigned int num_cores);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/include/linux/mali/mali_utgard_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/include/linux/mali/mali_utgard_ioctl.h
@@ -0,0 +1,100 @@
+/*
+ * Copyright (C) 2010-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+
+ * Class Path Exception
+ * Linking this library statically or dynamically with other modules is making a combined work based on this library. 
+ * Thus, the terms and conditions of the GNU General Public License cover the whole combination.
+ * As a special exception, the copyright holders of this library give you permission to link this library with independent modules 
+ * to produce an executable, regardless of the license terms of these independent modules, and to copy and distribute the resulting 
+ * executable under terms of your choice, provided that you also meet, for each linked independent module, the terms and conditions 
+ * of the license of that module. An independent module is a module which is not derived from or based on this library. If you modify 
+ * this library, you may extend this exception to your version of the library, but you are not obligated to do so. 
+ * If you do not wish to do so, delete this exception statement from your version.
+ */
+
+#ifndef __MALI_UTGARD_IOCTL_H__
+#define __MALI_UTGARD_IOCTL_H__
+
+#include <linux/types.h>
+#include <linux/ioctl.h>
+#include <linux/fs.h>       /* file system operations */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @file mali_kernel_ioctl.h
+ * Interface to the Linux device driver.
+ * This file describes the interface needed to use the Linux device driver.
+ * Its interface is designed to used by the HAL implementation through a thin arch layer.
+ */
+
+/**
+ * ioctl commands
+ */
+
+#define MALI_IOC_BASE           0x82
+#define MALI_IOC_CORE_BASE      (_MALI_UK_CORE_SUBSYSTEM      + MALI_IOC_BASE)
+#define MALI_IOC_MEMORY_BASE    (_MALI_UK_MEMORY_SUBSYSTEM    + MALI_IOC_BASE)
+#define MALI_IOC_PP_BASE        (_MALI_UK_PP_SUBSYSTEM        + MALI_IOC_BASE)
+#define MALI_IOC_GP_BASE        (_MALI_UK_GP_SUBSYSTEM        + MALI_IOC_BASE)
+#define MALI_IOC_PROFILING_BASE (_MALI_UK_PROFILING_SUBSYSTEM + MALI_IOC_BASE)
+#define MALI_IOC_VSYNC_BASE     (_MALI_UK_VSYNC_SUBSYSTEM + MALI_IOC_BASE)
+
+#define MALI_IOC_WAIT_FOR_NOTIFICATION      _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_WAIT_FOR_NOTIFICATION, _mali_uk_wait_for_notification_s)
+#define MALI_IOC_GET_API_VERSION            _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_GET_API_VERSION, u32)
+#define MALI_IOC_GET_API_VERSION_V2         _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_GET_API_VERSION, _mali_uk_get_api_version_v2_s)
+#define MALI_IOC_POST_NOTIFICATION          _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_POST_NOTIFICATION, _mali_uk_post_notification_s)
+#define MALI_IOC_GET_USER_SETTING           _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_GET_USER_SETTING, _mali_uk_get_user_setting_s)
+#define MALI_IOC_GET_USER_SETTINGS          _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_GET_USER_SETTINGS, _mali_uk_get_user_settings_s)
+#define MALI_IOC_REQUEST_HIGH_PRIORITY      _IOW (MALI_IOC_CORE_BASE, _MALI_UK_REQUEST_HIGH_PRIORITY, _mali_uk_request_high_priority_s)
+#define MALI_IOC_TIMELINE_GET_LATEST_POINT  _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_TIMELINE_GET_LATEST_POINT, _mali_uk_timeline_get_latest_point_s)
+#define MALI_IOC_TIMELINE_WAIT              _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_TIMELINE_WAIT, _mali_uk_timeline_wait_s)
+#define MALI_IOC_TIMELINE_CREATE_SYNC_FENCE _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_TIMELINE_CREATE_SYNC_FENCE, _mali_uk_timeline_create_sync_fence_s)
+#define MALI_IOC_SOFT_JOB_START             _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_SOFT_JOB_START, _mali_uk_soft_job_start_s)
+#define MALI_IOC_SOFT_JOB_SIGNAL            _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_SOFT_JOB_SIGNAL, _mali_uk_soft_job_signal_s)
+#define MALI_IOC_PENDING_SUBMIT             _IOWR(MALI_IOC_CORE_BASE, _MALI_UK_PENDING_SUBMIT, _mali_uk_pending_submit_s)
+
+#define MALI_IOC_MEM_ALLOC                  _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_ALLOC_MEM, _mali_uk_alloc_mem_s)
+#define MALI_IOC_MEM_FREE                   _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_FREE_MEM, _mali_uk_free_mem_s)
+#define MALI_IOC_MEM_BIND                   _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_BIND_MEM, _mali_uk_bind_mem_s)
+#define MALI_IOC_MEM_UNBIND                 _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_UNBIND_MEM, _mali_uk_unbind_mem_s)
+#define MALI_IOC_MEM_COW                    _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_COW_MEM, _mali_uk_cow_mem_s)
+#define MALI_IOC_MEM_COW_MODIFY_RANGE       _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_COW_MODIFY_RANGE, _mali_uk_cow_modify_range_s)
+#define MALI_IOC_MEM_RESIZE                 _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_RESIZE_MEM, _mali_uk_mem_resize_s)
+#define MALI_IOC_MEM_DMA_BUF_GET_SIZE       _IOR(MALI_IOC_MEMORY_BASE, _MALI_UK_DMA_BUF_GET_SIZE, _mali_uk_dma_buf_get_size_s)
+#define MALI_IOC_MEM_QUERY_MMU_PAGE_TABLE_DUMP_SIZE _IOR (MALI_IOC_MEMORY_BASE, _MALI_UK_QUERY_MMU_PAGE_TABLE_DUMP_SIZE, _mali_uk_query_mmu_page_table_dump_size_s)
+#define MALI_IOC_MEM_DUMP_MMU_PAGE_TABLE    _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_DUMP_MMU_PAGE_TABLE, _mali_uk_dump_mmu_page_table_s)
+#define MALI_IOC_MEM_WRITE_SAFE             _IOWR(MALI_IOC_MEMORY_BASE, _MALI_UK_MEM_WRITE_SAFE, _mali_uk_mem_write_safe_s)
+
+#define MALI_IOC_PP_START_JOB               _IOWR(MALI_IOC_PP_BASE, _MALI_UK_PP_START_JOB, _mali_uk_pp_start_job_s)
+#define MALI_IOC_PP_AND_GP_START_JOB        _IOWR(MALI_IOC_PP_BASE, _MALI_UK_PP_AND_GP_START_JOB, _mali_uk_pp_and_gp_start_job_s)
+#define MALI_IOC_PP_NUMBER_OF_CORES_GET     _IOR (MALI_IOC_PP_BASE, _MALI_UK_GET_PP_NUMBER_OF_CORES, _mali_uk_get_pp_number_of_cores_s)
+#define MALI_IOC_PP_CORE_VERSION_GET        _IOR (MALI_IOC_PP_BASE, _MALI_UK_GET_PP_CORE_VERSION, _mali_uk_get_pp_core_version_s)
+#define MALI_IOC_PP_DISABLE_WB              _IOW (MALI_IOC_PP_BASE, _MALI_UK_PP_DISABLE_WB, _mali_uk_pp_disable_wb_s)
+
+#define MALI_IOC_GP2_START_JOB              _IOWR(MALI_IOC_GP_BASE, _MALI_UK_GP_START_JOB, _mali_uk_gp_start_job_s)
+#define MALI_IOC_GP2_NUMBER_OF_CORES_GET    _IOR (MALI_IOC_GP_BASE, _MALI_UK_GET_GP_NUMBER_OF_CORES, _mali_uk_get_gp_number_of_cores_s)
+#define MALI_IOC_GP2_CORE_VERSION_GET       _IOR (MALI_IOC_GP_BASE, _MALI_UK_GET_GP_CORE_VERSION, _mali_uk_get_gp_core_version_s)
+#define MALI_IOC_GP2_SUSPEND_RESPONSE       _IOW (MALI_IOC_GP_BASE, _MALI_UK_GP_SUSPEND_RESPONSE,_mali_uk_gp_suspend_response_s)
+
+#define MALI_IOC_PROFILING_ADD_EVENT        _IOWR(MALI_IOC_PROFILING_BASE, _MALI_UK_PROFILING_ADD_EVENT, _mali_uk_profiling_add_event_s)
+#define MALI_IOC_PROFILING_REPORT_SW_COUNTERS  _IOW (MALI_IOC_PROFILING_BASE, _MALI_UK_PROFILING_REPORT_SW_COUNTERS, _mali_uk_sw_counters_report_s)
+#define MALI_IOC_PROFILING_MEMORY_USAGE_GET _IOR(MALI_IOC_PROFILING_BASE, _MALI_UK_PROFILING_MEMORY_USAGE_GET, _mali_uk_profiling_memory_usage_get_s)
+#define MALI_IOC_PROFILING_STREAM_FD_GET        _IOR(MALI_IOC_PROFILING_BASE, _MALI_UK_PROFILING_STREAM_FD_GET, _mali_uk_profiling_stream_fd_get_s)
+#define MALI_IOC_PROILING_CONTROL_SET   _IOR(MALI_IOC_PROFILING_BASE, _MALI_UK_PROFILING_CONTROL_SET, _mali_uk_profiling_control_set_s)
+
+#define MALI_IOC_VSYNC_EVENT_REPORT         _IOW (MALI_IOC_VSYNC_BASE, _MALI_UK_VSYNC_EVENT_REPORT, _mali_uk_vsync_event_report_s)
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_UTGARD_IOCTL_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/include/linux/mali/mali_utgard_profiling_events.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/include/linux/mali/mali_utgard_profiling_events.h
@@ -0,0 +1,200 @@
+/*
+ * Copyright (C) 2010-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+
+ * Class Path Exception
+ * Linking this library statically or dynamically with other modules is making a combined work based on this library. 
+ * Thus, the terms and conditions of the GNU General Public License cover the whole combination.
+ * As a special exception, the copyright holders of this library give you permission to link this library with independent modules 
+ * to produce an executable, regardless of the license terms of these independent modules, and to copy and distribute the resulting 
+ * executable under terms of your choice, provided that you also meet, for each linked independent module, the terms and conditions 
+ * of the license of that module. An independent module is a module which is not derived from or based on this library. If you modify 
+ * this library, you may extend this exception to your version of the library, but you are not obligated to do so. 
+ * If you do not wish to do so, delete this exception statement from your version.
+ */
+
+#ifndef _MALI_UTGARD_PROFILING_EVENTS_H_
+#define _MALI_UTGARD_PROFILING_EVENTS_H_
+
+/*
+ * The event ID is a 32 bit value consisting of different fields
+ * reserved, 4 bits, for future use
+ * event type, 4 bits, cinstr_profiling_event_type_t
+ * event channel, 8 bits, the source of the event.
+ * event data, 16 bit field, data depending on event type
+ */
+
+/**
+ * Specifies what kind of event this is
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_TYPE_SINGLE  = 0 << 24,
+	MALI_PROFILING_EVENT_TYPE_START   = 1 << 24,
+	MALI_PROFILING_EVENT_TYPE_STOP    = 2 << 24,
+	MALI_PROFILING_EVENT_TYPE_SUSPEND = 3 << 24,
+	MALI_PROFILING_EVENT_TYPE_RESUME  = 4 << 24,
+} cinstr_profiling_event_type_t;
+
+
+/**
+ * Secifies the channel/source of the event
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_CHANNEL_SOFTWARE =  0 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_GP0      =  1 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP0      =  5 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP1      =  6 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP2      =  7 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP3      =  8 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP4      =  9 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP5      = 10 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP6      = 11 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_PP7      = 12 << 16,
+	MALI_PROFILING_EVENT_CHANNEL_GPU      = 21 << 16,
+} cinstr_profiling_event_channel_t;
+
+
+#define MALI_PROFILING_MAKE_EVENT_CHANNEL_GP(num) (((MALI_PROFILING_EVENT_CHANNEL_GP0 >> 16) + (num)) << 16)
+#define MALI_PROFILING_MAKE_EVENT_CHANNEL_PP(num) (((MALI_PROFILING_EVENT_CHANNEL_PP0 >> 16) + (num)) << 16)
+
+/**
+ * These events are applicable when the type MALI_PROFILING_EVENT_TYPE_SINGLE is used from software channel
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_NONE                  = 0,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_NEW_FRAME         = 1,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_FLUSH                 = 2,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_SWAP_BUFFERS      = 3,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_FB_EVENT              = 4,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_GP_ENQUEUE            = 5,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_PP_ENQUEUE            = 6,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_READBACK              = 7,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_WRITEBACK             = 8,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_ENTER_API_FUNC        = 10,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_LEAVE_API_FUNC        = 11,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_DISCARD_ATTACHMENTS   = 13,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_UMP_TRY_LOCK          = 53,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_UMP_LOCK              = 54,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_UMP_UNLOCK            = 55,
+	MALI_PROFILING_EVENT_REASON_SINGLE_LOCK_CONTENDED           = 56,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_MALI_FENCE_DUP    = 57,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_SET_PP_JOB_FENCE  = 58,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_WAIT_SYNC         = 59,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_CREATE_FENCE_SYNC = 60,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_CREATE_NATIVE_FENCE_SYNC = 61,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_FENCE_FLUSH       = 62,
+	MALI_PROFILING_EVENT_REASON_SINGLE_SW_EGL_FLUSH_SERVER_WAITS = 63,
+} cinstr_profiling_event_reason_single_sw_t;
+
+/**
+ * These events are applicable when the type MALI_PROFILING_EVENT_TYPE_START/STOP is used from software channel
+ * to inform whether the core is physical or virtual
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_REASON_START_STOP_HW_PHYSICAL  = 0,
+	MALI_PROFILING_EVENT_REASON_START_STOP_HW_VIRTUAL   = 1,
+} cinstr_profiling_event_reason_start_stop_hw_t;
+
+/**
+ * These events are applicable when the type MALI_PROFILING_EVENT_TYPE_START/STOP is used from software channel
+ */
+typedef enum {
+	/*MALI_PROFILING_EVENT_REASON_START_STOP_SW_NONE            = 0,*/
+	MALI_PROFILING_EVENT_REASON_START_STOP_SW_MALI            = 1,
+	MALI_PROFILING_EVENT_REASON_START_STOP_SW_CALLBACK_THREAD = 2,
+	MALI_PROFILING_EVENT_REASON_START_STOP_SW_WORKER_THREAD   = 3,
+	MALI_PROFILING_EVENT_REASON_START_STOP_SW_BOTTOM_HALF     = 4,
+	MALI_PROFILING_EVENT_REASON_START_STOP_SW_UPPER_HALF      = 5,
+} cinstr_profiling_event_reason_start_stop_sw_t;
+
+/**
+ * These events are applicable when the type MALI_PROFILING_EVENT_TYPE_SUSPEND/RESUME is used from software channel
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_NONE                     =  0, /* used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_PIPELINE_FULL            =  1, /* NOT used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_VSYNC                    = 26, /* used in some build configurations */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_FB_IFRAME_WAIT           = 27, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_FB_IFRAME_SYNC           = 28, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_VG_WAIT_FILTER_CLEANUP   = 29, /* used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_VG_WAIT_TEXTURE          = 30, /* used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_GLES_WAIT_MIPLEVEL       = 31, /* used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_GLES_WAIT_READPIXELS     = 32, /* used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_EGL_WAIT_SWAP_IMMEDIATE  = 33, /* NOT used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_ICS_QUEUE_BUFFER         = 34, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_ICS_DEQUEUE_BUFFER       = 35, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_UMP_LOCK                 = 36, /* Not currently used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_X11_GLOBAL_LOCK          = 37, /* Not currently used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_X11_SWAP                 = 38, /* Not currently used */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_MALI_EGL_IMAGE_SYNC_WAIT = 39, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_GP_JOB_HANDLING          = 40, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_PP_JOB_HANDLING          = 41, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_EGL_MALI_FENCE_MERGE     = 42, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_EGL_MALI_FENCE_DUP       = 43,
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_EGL_FLUSH_SERVER_WAITS   = 44,
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_EGL_WAIT_SYNC            = 45, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_FB_JOBS_WAIT             = 46, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_FB_NOFRAMES_WAIT         = 47, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_FB_NOJOBS_WAIT           = 48, /* USED */
+	MALI_PROFILING_EVENT_REASON_SUSPEND_RESUME_SW_SUBMIT_LIMITER_WAIT      = 49, /* USED */
+} cinstr_profiling_event_reason_suspend_resume_sw_t;
+
+/**
+ * These events are applicable when the type MALI_PROFILING_EVENT_TYPE_SINGLE is used from a HW channel (GPx+PPx)
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_REASON_SINGLE_HW_NONE          = 0,
+	MALI_PROFILING_EVENT_REASON_SINGLE_HW_INTERRUPT     = 1,
+	MALI_PROFILING_EVENT_REASON_SINGLE_HW_FLUSH         = 2,
+} cinstr_profiling_event_reason_single_hw_t;
+
+/**
+ * These events are applicable when the type MALI_PROFILING_EVENT_TYPE_SINGLE is used from the GPU channel
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_REASON_SINGLE_GPU_NONE              = 0,
+	MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE  = 1,
+	MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L20_COUNTERS      = 2,
+	MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L21_COUNTERS      = 3,
+	MALI_PROFILING_EVENT_REASON_SINGLE_GPU_L22_COUNTERS      = 4,
+} cinstr_profiling_event_reason_single_gpu_t;
+
+/**
+ * These values are applicable for the 3rd data parameter when
+ * the type MALI_PROFILING_EVENT_TYPE_START is used from the software channel
+ * with the MALI_PROFILING_EVENT_REASON_START_STOP_BOTTOM_HALF reason.
+ */
+typedef enum {
+	MALI_PROFILING_EVENT_DATA_CORE_GP0             =  1,
+	MALI_PROFILING_EVENT_DATA_CORE_PP0             =  5,
+	MALI_PROFILING_EVENT_DATA_CORE_PP1             =  6,
+	MALI_PROFILING_EVENT_DATA_CORE_PP2             =  7,
+	MALI_PROFILING_EVENT_DATA_CORE_PP3             =  8,
+	MALI_PROFILING_EVENT_DATA_CORE_PP4             =  9,
+	MALI_PROFILING_EVENT_DATA_CORE_PP5             = 10,
+	MALI_PROFILING_EVENT_DATA_CORE_PP6             = 11,
+	MALI_PROFILING_EVENT_DATA_CORE_PP7             = 12,
+	MALI_PROFILING_EVENT_DATA_CORE_GP0_MMU         = 22, /* GP0 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP0_MMU         = 26, /* PP0 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP1_MMU         = 27, /* PP1 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP2_MMU         = 28, /* PP2 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP3_MMU         = 29, /* PP3 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP4_MMU         = 30, /* PP4 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP5_MMU         = 31, /* PP5 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP6_MMU         = 32, /* PP6 + 21 */
+	MALI_PROFILING_EVENT_DATA_CORE_PP7_MMU         = 33, /* PP7 + 21 */
+
+} cinstr_profiling_event_data_core_t;
+
+#define MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP(num) (MALI_PROFILING_EVENT_DATA_CORE_GP0 + (num))
+#define MALI_PROFILING_MAKE_EVENT_DATA_CORE_GP_MMU(num) (MALI_PROFILING_EVENT_DATA_CORE_GP0_MMU + (num))
+#define MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP(num) (MALI_PROFILING_EVENT_DATA_CORE_PP0 + (num))
+#define MALI_PROFILING_MAKE_EVENT_DATA_CORE_PP_MMU(num) (MALI_PROFILING_EVENT_DATA_CORE_PP0_MMU + (num))
+
+
+#endif /*_MALI_UTGARD_PROFILING_EVENTS_H_*/
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/include/linux/mali/mali_utgard_profiling_gator_api.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/include/linux/mali/mali_utgard_profiling_gator_api.h
@@ -0,0 +1,315 @@
+/*
+ * Copyright (C) 2010-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+
+ * Class Path Exception
+ * Linking this library statically or dynamically with other modules is making a combined work based on this library. 
+ * Thus, the terms and conditions of the GNU General Public License cover the whole combination.
+ * As a special exception, the copyright holders of this library give you permission to link this library with independent modules 
+ * to produce an executable, regardless of the license terms of these independent modules, and to copy and distribute the resulting 
+ * executable under terms of your choice, provided that you also meet, for each linked independent module, the terms and conditions 
+ * of the license of that module. An independent module is a module which is not derived from or based on this library. If you modify 
+ * this library, you may extend this exception to your version of the library, but you are not obligated to do so. 
+ * If you do not wish to do so, delete this exception statement from your version.
+ */
+
+#ifndef __MALI_UTGARD_PROFILING_GATOR_API_H__
+#define __MALI_UTGARD_PROFILING_GATOR_API_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#define MALI_PROFILING_API_VERSION 4
+
+#define MAX_NUM_L2_CACHE_CORES 3
+#define MAX_NUM_FP_CORES 8
+#define MAX_NUM_VP_CORES 1
+
+#define _MALI_SPCIAL_COUNTER_DESCRIPTIONS \
+	{                                           \
+		"Filmstrip_cnt0",                 \
+		"Frequency",       \
+		"Voltage",       \
+		"vertex",     \
+		"fragment",         \
+		"Total_alloc_pages",        \
+	};
+
+#define _MALI_MEM_COUTNER_DESCRIPTIONS \
+	{                                           \
+		"untyped_memory",                 \
+		"vertex_index_buffer",       \
+		"texture_buffer",       \
+		"varying_buffer",     \
+		"render_target",         \
+		"pbuffer_buffer",        \
+		"plbu_heap",            \
+		"pointer_array_buffer",             \
+		"slave_tilelist",          \
+		"untyped_gp_cmdlist",     \
+		"polygon_cmdlist",               \
+		"texture_descriptor",               \
+		"render_state_word",               \
+		"shader",               \
+		"stream_buffer",               \
+		"fragment_stack",               \
+		"uniform",               \
+		"untyped_frame_pool",               \
+		"untyped_surface",               \
+	};
+
+/** The list of events supported by the Mali DDK. */
+typedef enum {
+	/* Vertex processor activity */
+	ACTIVITY_VP_0 = 0,
+
+	/* Fragment processor activity */
+	ACTIVITY_FP_0,
+	ACTIVITY_FP_1,
+	ACTIVITY_FP_2,
+	ACTIVITY_FP_3,
+	ACTIVITY_FP_4,
+	ACTIVITY_FP_5,
+	ACTIVITY_FP_6,
+	ACTIVITY_FP_7,
+
+	/* L2 cache counters */
+	COUNTER_L2_0_C0,
+	COUNTER_L2_0_C1,
+	COUNTER_L2_1_C0,
+	COUNTER_L2_1_C1,
+	COUNTER_L2_2_C0,
+	COUNTER_L2_2_C1,
+
+	/* Vertex processor counters */
+	COUNTER_VP_0_C0,
+	COUNTER_VP_0_C1,
+
+	/* Fragment processor counters */
+	COUNTER_FP_0_C0,
+	COUNTER_FP_0_C1,
+	COUNTER_FP_1_C0,
+	COUNTER_FP_1_C1,
+	COUNTER_FP_2_C0,
+	COUNTER_FP_2_C1,
+	COUNTER_FP_3_C0,
+	COUNTER_FP_3_C1,
+	COUNTER_FP_4_C0,
+	COUNTER_FP_4_C1,
+	COUNTER_FP_5_C0,
+	COUNTER_FP_5_C1,
+	COUNTER_FP_6_C0,
+	COUNTER_FP_6_C1,
+	COUNTER_FP_7_C0,
+	COUNTER_FP_7_C1,
+
+	/*
+	 * If more hardware counters are added, the _mali_osk_hw_counter_table
+	 * below should also be updated.
+	 */
+
+	/* EGL software counters */
+	COUNTER_EGL_BLIT_TIME,
+
+	/* GLES software counters */
+	COUNTER_GLES_DRAW_ELEMENTS_CALLS,
+	COUNTER_GLES_DRAW_ELEMENTS_NUM_INDICES,
+	COUNTER_GLES_DRAW_ELEMENTS_NUM_TRANSFORMED,
+	COUNTER_GLES_DRAW_ARRAYS_CALLS,
+	COUNTER_GLES_DRAW_ARRAYS_NUM_TRANSFORMED,
+	COUNTER_GLES_DRAW_POINTS,
+	COUNTER_GLES_DRAW_LINES,
+	COUNTER_GLES_DRAW_LINE_LOOP,
+	COUNTER_GLES_DRAW_LINE_STRIP,
+	COUNTER_GLES_DRAW_TRIANGLES,
+	COUNTER_GLES_DRAW_TRIANGLE_STRIP,
+	COUNTER_GLES_DRAW_TRIANGLE_FAN,
+	COUNTER_GLES_NON_VBO_DATA_COPY_TIME,
+	COUNTER_GLES_UNIFORM_BYTES_COPIED_TO_MALI,
+	COUNTER_GLES_UPLOAD_TEXTURE_TIME,
+	COUNTER_GLES_UPLOAD_VBO_TIME,
+	COUNTER_GLES_NUM_FLUSHES,
+	COUNTER_GLES_NUM_VSHADERS_GENERATED,
+	COUNTER_GLES_NUM_FSHADERS_GENERATED,
+	COUNTER_GLES_VSHADER_GEN_TIME,
+	COUNTER_GLES_FSHADER_GEN_TIME,
+	COUNTER_GLES_INPUT_TRIANGLES,
+	COUNTER_GLES_VXCACHE_HIT,
+	COUNTER_GLES_VXCACHE_MISS,
+	COUNTER_GLES_VXCACHE_COLLISION,
+	COUNTER_GLES_CULLED_TRIANGLES,
+	COUNTER_GLES_CULLED_LINES,
+	COUNTER_GLES_BACKFACE_TRIANGLES,
+	COUNTER_GLES_GBCLIP_TRIANGLES,
+	COUNTER_GLES_GBCLIP_LINES,
+	COUNTER_GLES_TRIANGLES_DRAWN,
+	COUNTER_GLES_DRAWCALL_TIME,
+	COUNTER_GLES_TRIANGLES_COUNT,
+	COUNTER_GLES_INDEPENDENT_TRIANGLES_COUNT,
+	COUNTER_GLES_STRIP_TRIANGLES_COUNT,
+	COUNTER_GLES_FAN_TRIANGLES_COUNT,
+	COUNTER_GLES_LINES_COUNT,
+	COUNTER_GLES_INDEPENDENT_LINES_COUNT,
+	COUNTER_GLES_STRIP_LINES_COUNT,
+	COUNTER_GLES_LOOP_LINES_COUNT,
+
+	/* Special counter */
+
+	/* Framebuffer capture pseudo-counter */
+	COUNTER_FILMSTRIP,
+	COUNTER_FREQUENCY,
+	COUNTER_VOLTAGE,
+	COUNTER_VP_ACTIVITY,
+	COUNTER_FP_ACTIVITY,
+	COUNTER_TOTAL_ALLOC_PAGES,
+
+	/* Memory usage counter */
+	COUNTER_MEM_UNTYPED,
+	COUNTER_MEM_VB_IB,
+	COUNTER_MEM_TEXTURE,
+	COUNTER_MEM_VARYING,
+	COUNTER_MEM_RT,
+	COUNTER_MEM_PBUFFER,
+	/* memory usages for gp command */
+	COUNTER_MEM_PLBU_HEAP,
+	COUNTER_MEM_POINTER_ARRAY,
+	COUNTER_MEM_SLAVE_TILELIST,
+	COUNTER_MEM_UNTYPE_GP_CMDLIST,
+	/* memory usages for polygon list command */
+	COUNTER_MEM_POLYGON_CMDLIST,
+	/* memory usages for pp command */
+	COUNTER_MEM_TD,
+	COUNTER_MEM_RSW,
+	/* other memory usages */
+	COUNTER_MEM_SHADER,
+	COUNTER_MEM_STREAMS,
+	COUNTER_MEM_FRAGMENT_STACK,
+	COUNTER_MEM_UNIFORM,
+	/* Special mem usage, which is used for mem pool allocation */
+	COUNTER_MEM_UNTYPE_MEM_POOL,
+	COUNTER_MEM_UNTYPE_SURFACE,
+
+	NUMBER_OF_EVENTS
+} _mali_osk_counter_id;
+
+#define FIRST_ACTIVITY_EVENT    ACTIVITY_VP_0
+#define LAST_ACTIVITY_EVENT     ACTIVITY_FP_7
+
+#define FIRST_HW_COUNTER        COUNTER_L2_0_C0
+#define LAST_HW_COUNTER         COUNTER_FP_7_C1
+
+#define FIRST_SW_COUNTER        COUNTER_EGL_BLIT_TIME
+#define LAST_SW_COUNTER         COUNTER_GLES_LOOP_LINES_COUNT
+
+#define FIRST_SPECIAL_COUNTER   COUNTER_FILMSTRIP
+#define LAST_SPECIAL_COUNTER    COUNTER_TOTAL_ALLOC_PAGES
+
+#define FIRST_MEM_COUNTER               COUNTER_MEM_UNTYPED
+#define LAST_MEM_COUNTER                COUNTER_MEM_UNTYPE_SURFACE
+
+#define MALI_PROFILING_MEM_COUNTERS_NUM (LAST_MEM_COUNTER - FIRST_MEM_COUNTER + 1)
+#define MALI_PROFILING_SPECIAL_COUNTERS_NUM     (LAST_SPECIAL_COUNTER - FIRST_SPECIAL_COUNTER + 1)
+#define MALI_PROFILING_SW_COUNTERS_NUM  (LAST_SW_COUNTER - FIRST_SW_COUNTER + 1)
+
+/**
+ * Define the stream header type for porfiling stream.
+ */
+#define  STREAM_HEADER_FRAMEBUFFER 0x05         /* The stream packet header type for framebuffer dumping. */
+#define STREAM_HEADER_COUNTER_VALUE  0x09       /* The stream packet header type for hw/sw/memory counter sampling. */
+#define STREAM_HEADER_CORE_ACTIVITY 0x0a                /* The stream packet header type for activity counter sampling. */
+#define STREAM_HEADER_SIZE      5
+
+/**
+ * Define the packet header type of profiling control packet.
+ */
+#define PACKET_HEADER_ERROR            0x80             /* The response packet header type if error. */
+#define PACKET_HEADER_ACK              0x81             /* The response packet header type if OK. */
+#define PACKET_HEADER_COUNTERS_REQUEST 0x82             /* The control packet header type to request counter information from ddk. */
+#define PACKET_HEADER_COUNTERS_ACK         0x83         /* The response packet header type to send out counter information. */
+#define PACKET_HEADER_COUNTERS_ENABLE  0x84             /* The control packet header type to enable counters. */
+#define PACKET_HEADER_START_CAPTURE_VALUE            0x85               /* The control packet header type to start capture values. */
+
+#define PACKET_HEADER_SIZE      5
+
+/**
+ * Structure to pass performance counter data of a Mali core
+ */
+typedef struct _mali_profiling_core_counters {
+	u32 source0;
+	u32 value0;
+	u32 source1;
+	u32 value1;
+} _mali_profiling_core_counters;
+
+/**
+ * Structure to pass performance counter data of Mali L2 cache cores
+ */
+typedef struct _mali_profiling_l2_counter_values {
+	struct _mali_profiling_core_counters cores[MAX_NUM_L2_CACHE_CORES];
+} _mali_profiling_l2_counter_values;
+
+/**
+ * Structure to pass data defining Mali instance in use:
+ *
+ * mali_product_id - Mali product id
+ * mali_version_major - Mali version major number
+ * mali_version_minor - Mali version minor number
+ * num_of_l2_cores - number of L2 cache cores
+ * num_of_fp_cores - number of fragment processor cores
+ * num_of_vp_cores - number of vertex processor cores
+ */
+typedef struct _mali_profiling_mali_version {
+	u32 mali_product_id;
+	u32 mali_version_major;
+	u32 mali_version_minor;
+	u32 num_of_l2_cores;
+	u32 num_of_fp_cores;
+	u32 num_of_vp_cores;
+} _mali_profiling_mali_version;
+
+/**
+ * Structure to define the mali profiling counter struct.
+ */
+typedef struct mali_profiling_counter {
+	char counter_name[40];
+	u32 counter_id;
+	u32 counter_event;
+	u32 prev_counter_value;
+	u32 current_counter_value;
+	u32 key;
+	int enabled;
+} mali_profiling_counter;
+
+/*
+ * List of possible actions to be controlled by Streamline.
+ * The following numbers are used by gator to control the frame buffer dumping and s/w counter reporting.
+ * We cannot use the enums in mali_uk_types.h because they are unknown inside gator.
+ */
+#define FBDUMP_CONTROL_ENABLE (1)
+#define FBDUMP_CONTROL_RATE (2)
+#define SW_COUNTER_ENABLE (3)
+#define FBDUMP_CONTROL_RESIZE_FACTOR (4)
+#define MEM_COUNTER_ENABLE (5)
+#define ANNOTATE_PROFILING_ENABLE (6)
+
+void _mali_profiling_control(u32 action, u32 value);
+
+u32 _mali_profiling_get_l2_counters(_mali_profiling_l2_counter_values *values);
+
+int _mali_profiling_set_event(u32 counter_id, s32 event_id);
+
+u32 _mali_profiling_get_api_version(void);
+
+void _mali_profiling_get_mali_version(struct _mali_profiling_mali_version *values);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_UTGARD_PROFILING_GATOR_API_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/include/linux/mali/mali_utgard_uk_types.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/include/linux/mali/mali_utgard_uk_types.h
@@ -0,0 +1,1100 @@
+/*
+ * Copyright (C) 2010-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+
+ * Class Path Exception
+ * Linking this library statically or dynamically with other modules is making a combined work based on this library. 
+ * Thus, the terms and conditions of the GNU General Public License cover the whole combination.
+ * As a special exception, the copyright holders of this library give you permission to link this library with independent modules 
+ * to produce an executable, regardless of the license terms of these independent modules, and to copy and distribute the resulting 
+ * executable under terms of your choice, provided that you also meet, for each linked independent module, the terms and conditions 
+ * of the license of that module. An independent module is a module which is not derived from or based on this library. If you modify 
+ * this library, you may extend this exception to your version of the library, but you are not obligated to do so. 
+ * If you do not wish to do so, delete this exception statement from your version.
+ */
+
+/**
+ * @file mali_uk_types.h
+ * Defines the types and constants used in the user-kernel interface
+ */
+
+#ifndef __MALI_UTGARD_UK_TYPES_H__
+#define __MALI_UTGARD_UK_TYPES_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Iteration functions depend on these values being consecutive. */
+#define MALI_UK_TIMELINE_GP   0
+#define MALI_UK_TIMELINE_PP   1
+#define MALI_UK_TIMELINE_SOFT 2
+#define MALI_UK_TIMELINE_MAX  3
+
+#define MALI_UK_BIG_VARYING_SIZE  (1024*1024*2)
+
+typedef struct {
+	u32 points[MALI_UK_TIMELINE_MAX];
+	s32 sync_fd;
+} _mali_uk_fence_t;
+
+/**
+ * @addtogroup uddapi Unified Device Driver (UDD) APIs
+ *
+ * @{
+ */
+
+/**
+ * @addtogroup u_k_api UDD User/Kernel Interface (U/K) APIs
+ *
+ * @{
+ */
+
+/** @defgroup _mali_uk_core U/K Core
+ * @{ */
+
+/** Definition of subsystem numbers, to assist in creating a unique identifier
+ * for each U/K call.
+ *
+ * @see _mali_uk_functions */
+typedef enum {
+	_MALI_UK_CORE_SUBSYSTEM,      /**< Core Group of U/K calls */
+	_MALI_UK_MEMORY_SUBSYSTEM,    /**< Memory Group of U/K calls */
+	_MALI_UK_PP_SUBSYSTEM,        /**< Fragment Processor Group of U/K calls */
+	_MALI_UK_GP_SUBSYSTEM,        /**< Vertex Processor Group of U/K calls */
+	_MALI_UK_PROFILING_SUBSYSTEM, /**< Profiling Group of U/K calls */
+	_MALI_UK_VSYNC_SUBSYSTEM,     /**< VSYNC Group of U/K calls */
+} _mali_uk_subsystem_t;
+
+/** Within a function group each function has its unique sequence number
+ * to assist in creating a unique identifier for each U/K call.
+ *
+ * An ordered pair of numbers selected from
+ * ( \ref _mali_uk_subsystem_t,\ref  _mali_uk_functions) will uniquely identify the
+ * U/K call across all groups of functions, and all functions. */
+typedef enum {
+	/** Core functions */
+
+	_MALI_UK_OPEN                    = 0, /**< _mali_ukk_open() */
+	_MALI_UK_CLOSE,                       /**< _mali_ukk_close() */
+	_MALI_UK_WAIT_FOR_NOTIFICATION,       /**< _mali_ukk_wait_for_notification() */
+	_MALI_UK_GET_API_VERSION,             /**< _mali_ukk_get_api_version() */
+	_MALI_UK_POST_NOTIFICATION,           /**< _mali_ukk_post_notification() */
+	_MALI_UK_GET_USER_SETTING,            /**< _mali_ukk_get_user_setting() *//**< [out] */
+	_MALI_UK_GET_USER_SETTINGS,           /**< _mali_ukk_get_user_settings() *//**< [out] */
+	_MALI_UK_REQUEST_HIGH_PRIORITY,       /**< _mali_ukk_request_high_priority() */
+	_MALI_UK_TIMELINE_GET_LATEST_POINT,   /**< _mali_ukk_timeline_get_latest_point() */
+	_MALI_UK_TIMELINE_WAIT,               /**< _mali_ukk_timeline_wait() */
+	_MALI_UK_TIMELINE_CREATE_SYNC_FENCE,  /**< _mali_ukk_timeline_create_sync_fence() */
+	_MALI_UK_SOFT_JOB_START,              /**< _mali_ukk_soft_job_start() */
+	_MALI_UK_SOFT_JOB_SIGNAL,             /**< _mali_ukk_soft_job_signal() */
+	_MALI_UK_PENDING_SUBMIT,             /**< _mali_ukk_pending_submit() */
+
+	/** Memory functions */
+
+	_MALI_UK_ALLOC_MEM                = 0,   /**< _mali_ukk_alloc_mem() */
+	_MALI_UK_FREE_MEM,                       /**< _mali_ukk_free_mem() */
+	_MALI_UK_BIND_MEM,                       /**< _mali_ukk_mem_bind() */
+	_MALI_UK_UNBIND_MEM,                     /**< _mali_ukk_mem_unbind() */
+	_MALI_UK_COW_MEM,                        /**< _mali_ukk_mem_cow() */
+	_MALI_UK_COW_MODIFY_RANGE,               /**< _mali_ukk_mem_cow_modify_range() */
+	_MALI_UK_RESIZE_MEM,                     /**<._mali_ukk_mem_resize() */
+	_MALI_UK_QUERY_MMU_PAGE_TABLE_DUMP_SIZE, /**< _mali_ukk_mem_get_mmu_page_table_dump_size() */
+	_MALI_UK_DUMP_MMU_PAGE_TABLE,            /**< _mali_ukk_mem_dump_mmu_page_table() */
+	_MALI_UK_DMA_BUF_GET_SIZE,               /**< _mali_ukk_dma_buf_get_size() */
+	_MALI_UK_MEM_WRITE_SAFE,                 /**< _mali_uku_mem_write_safe() */
+
+	/** Common functions for each core */
+
+	_MALI_UK_START_JOB           = 0,     /**< Start a Fragment/Vertex Processor Job on a core */
+	_MALI_UK_GET_NUMBER_OF_CORES,         /**< Get the number of Fragment/Vertex Processor cores */
+	_MALI_UK_GET_CORE_VERSION,            /**< Get the Fragment/Vertex Processor version compatible with all cores */
+
+	/** Fragment Processor Functions  */
+
+	_MALI_UK_PP_START_JOB            = _MALI_UK_START_JOB,            /**< _mali_ukk_pp_start_job() */
+	_MALI_UK_GET_PP_NUMBER_OF_CORES  = _MALI_UK_GET_NUMBER_OF_CORES,  /**< _mali_ukk_get_pp_number_of_cores() */
+	_MALI_UK_GET_PP_CORE_VERSION     = _MALI_UK_GET_CORE_VERSION,     /**< _mali_ukk_get_pp_core_version() */
+	_MALI_UK_PP_DISABLE_WB,                                           /**< _mali_ukk_pp_job_disable_wb() */
+	_MALI_UK_PP_AND_GP_START_JOB,                                     /**< _mali_ukk_pp_and_gp_start_job() */
+
+	/** Vertex Processor Functions  */
+
+	_MALI_UK_GP_START_JOB            = _MALI_UK_START_JOB,            /**< _mali_ukk_gp_start_job() */
+	_MALI_UK_GET_GP_NUMBER_OF_CORES  = _MALI_UK_GET_NUMBER_OF_CORES,  /**< _mali_ukk_get_gp_number_of_cores() */
+	_MALI_UK_GET_GP_CORE_VERSION     = _MALI_UK_GET_CORE_VERSION,     /**< _mali_ukk_get_gp_core_version() */
+	_MALI_UK_GP_SUSPEND_RESPONSE,                                     /**< _mali_ukk_gp_suspend_response() */
+
+	/** Profiling functions */
+
+	_MALI_UK_PROFILING_ADD_EVENT     = 0, /**< __mali_uku_profiling_add_event() */
+	_MALI_UK_PROFILING_REPORT_SW_COUNTERS,/**< __mali_uku_profiling_report_sw_counters() */
+	_MALI_UK_PROFILING_MEMORY_USAGE_GET,  /**< __mali_uku_profiling_memory_usage_get() */
+	_MALI_UK_PROFILING_STREAM_FD_GET, /** < __mali_uku_profiling_stream_fd_get() */
+	_MALI_UK_PROFILING_CONTROL_SET, /** < __mali_uku_profiling_control_set() */
+
+	/** VSYNC reporting fuctions */
+	_MALI_UK_VSYNC_EVENT_REPORT      = 0, /**< _mali_ukk_vsync_event_report() */
+} _mali_uk_functions;
+
+/** @defgroup _mali_uk_getsysteminfo U/K Get System Info
+ * @{ */
+
+/**
+ * Type definition for the core version number.
+ * Used when returning the version number read from a core
+ *
+ * Its format is that of the 32-bit Version register for a particular core.
+ * Refer to the "Mali200 and MaliGP2 3D Graphics Processor Technical Reference
+ * Manual", ARM DDI 0415C, for more information.
+ */
+typedef u32 _mali_core_version;
+
+/** @} */ /* end group _mali_uk_core */
+
+
+/** @defgroup _mali_uk_gp U/K Vertex Processor
+ * @{ */
+
+/** @defgroup _mali_uk_gp_suspend_response_s Vertex Processor Suspend Response
+ * @{ */
+
+/** @brief Arguments for _mali_ukk_gp_suspend_response()
+ *
+ * When _mali_wait_for_notification() receives notification that a
+ * Vertex Processor job was suspended, you need to send a response to indicate
+ * what needs to happen with this job. You can either abort or resume the job.
+ *
+ * - set @c code to indicate response code. This is either @c _MALIGP_JOB_ABORT or
+ * @c _MALIGP_JOB_RESUME_WITH_NEW_HEAP to indicate you will provide a new heap
+ * for the job that will resolve the out of memory condition for the job.
+ * - copy the @c cookie value from the @c _mali_uk_gp_job_suspended_s notification;
+ * this is an identifier for the suspended job
+ * - set @c arguments[0] and @c arguments[1] to zero if you abort the job. If
+ * you resume it, @c argument[0] should specify the Mali start address for the new
+ * heap and @c argument[1] the Mali end address of the heap.
+ * - pass in the user-kernel context @c ctx that was returned from _mali_ukk_open()
+ *
+ */
+typedef enum _maligp_job_suspended_response_code {
+	_MALIGP_JOB_ABORT,                  /**< Abort the Vertex Processor job */
+	_MALIGP_JOB_RESUME_WITH_NEW_HEAP    /**< Resume the Vertex Processor job with a new heap */
+} _maligp_job_suspended_response_code;
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 cookie;                     /**< [in] cookie from the _mali_uk_gp_job_suspended_s notification */
+	_maligp_job_suspended_response_code code; /**< [in] abort or resume response code, see \ref _maligp_job_suspended_response_code */
+	u32 arguments[2];               /**< [in] 0 when aborting a job. When resuming a job, the Mali start and end address for a new heap to resume the job with */
+} _mali_uk_gp_suspend_response_s;
+
+/** @} */ /* end group _mali_uk_gp_suspend_response_s */
+
+/** @defgroup _mali_uk_gpstartjob_s Vertex Processor Start Job
+ * @{ */
+
+/** @brief Status indicating the result of the execution of a Vertex or Fragment processor job  */
+typedef enum {
+	_MALI_UK_JOB_STATUS_END_SUCCESS         = 1 << (16 + 0),
+	_MALI_UK_JOB_STATUS_END_OOM             = 1 << (16 + 1),
+	_MALI_UK_JOB_STATUS_END_ABORT           = 1 << (16 + 2),
+	_MALI_UK_JOB_STATUS_END_TIMEOUT_SW      = 1 << (16 + 3),
+	_MALI_UK_JOB_STATUS_END_HANG            = 1 << (16 + 4),
+	_MALI_UK_JOB_STATUS_END_SEG_FAULT       = 1 << (16 + 5),
+	_MALI_UK_JOB_STATUS_END_ILLEGAL_JOB     = 1 << (16 + 6),
+	_MALI_UK_JOB_STATUS_END_UNKNOWN_ERR     = 1 << (16 + 7),
+	_MALI_UK_JOB_STATUS_END_SHUTDOWN        = 1 << (16 + 8),
+	_MALI_UK_JOB_STATUS_END_SYSTEM_UNUSABLE = 1 << (16 + 9)
+} _mali_uk_job_status;
+
+#define MALIGP2_NUM_REGS_FRAME (6)
+
+/** @brief Arguments for _mali_ukk_gp_start_job()
+ *
+ * To start a Vertex Processor job
+ * - associate the request with a reference to a @c mali_gp_job_info by setting
+ * user_job_ptr to the address of the @c mali_gp_job_info of the job.
+ * - set @c priority to the priority of the @c mali_gp_job_info
+ * - specify a timeout for the job by setting @c watchdog_msecs to the number of
+ * milliseconds the job is allowed to run. Specifying a value of 0 selects the
+ * default timeout in use by the device driver.
+ * - copy the frame registers from the @c mali_gp_job_info into @c frame_registers.
+ * - set the @c perf_counter_flag, @c perf_counter_src0 and @c perf_counter_src1 to zero
+ * for a non-instrumented build. For an instrumented build you can use up
+ * to two performance counters. Set the corresponding bit in @c perf_counter_flag
+ * to enable them. @c perf_counter_src0 and @c perf_counter_src1 specify
+ * the source of what needs to get counted (e.g. number of vertex loader
+ * cache hits). For source id values, see ARM DDI0415A, Table 3-60.
+ * - pass in the user-kernel context @c ctx that was returned from _mali_ukk_open()
+ *
+ * When @c _mali_ukk_gp_start_job() returns @c _MALI_OSK_ERR_OK, status contains the
+ * result of the request (see \ref _mali_uk_start_job_status). If the job could
+ * not get started (@c _MALI_UK_START_JOB_NOT_STARTED_DO_REQUEUE) it should be
+ * tried again.
+ *
+ * After the job has started, @c _mali_wait_for_notification() will be notified
+ * that the job finished or got suspended. It may get suspended due to
+ * resource shortage. If it finished (see _mali_ukk_wait_for_notification())
+ * the notification will contain a @c _mali_uk_gp_job_finished_s result. If
+ * it got suspended the notification will contain a @c _mali_uk_gp_job_suspended_s
+ * result.
+ *
+ * The @c _mali_uk_gp_job_finished_s contains the job status (see \ref _mali_uk_job_status),
+ * the number of milliseconds the job took to render, and values of core registers
+ * when the job finished (irq status, performance counters, renderer list
+ * address). A job has finished succesfully when its status is
+ * @c _MALI_UK_JOB_STATUS_FINISHED. If the hardware detected a timeout while rendering
+ * the job, or software detected the job is taking more than watchdog_msecs to
+ * complete, the status will indicate @c _MALI_UK_JOB_STATUS_HANG.
+ * If the hardware detected a bus error while accessing memory associated with the
+ * job, status will indicate @c _MALI_UK_JOB_STATUS_SEG_FAULT.
+ * status will indicate @c _MALI_UK_JOB_STATUS_NOT_STARTED if the driver had to
+ * stop the job but the job didn't start on the hardware yet, e.g. when the
+ * driver shutdown.
+ *
+ * In case the job got suspended, @c _mali_uk_gp_job_suspended_s contains
+ * the @c user_job_ptr identifier used to start the job with, the @c reason
+ * why the job stalled (see \ref _maligp_job_suspended_reason) and a @c cookie
+ * to identify the core on which the job stalled.  This @c cookie will be needed
+ * when responding to this nofication by means of _mali_ukk_gp_suspend_response().
+ * (see _mali_ukk_gp_suspend_response()). The response is either to abort or
+ * resume the job. If the job got suspended due to an out of memory condition
+ * you may be able to resolve this by providing more memory and resuming the job.
+ *
+ */
+typedef struct {
+	u64 ctx;                          /**< [in,out] user-kernel context (trashed on output) */
+	u64 user_job_ptr;                   /**< [in] identifier for the job in user space, a @c mali_gp_job_info* */
+	u32 priority;                       /**< [in] job priority. A lower number means higher priority */
+	u32 frame_registers[MALIGP2_NUM_REGS_FRAME]; /**< [in] core specific registers associated with this job */
+	u32 perf_counter_flag;              /**< [in] bitmask indicating which performance counters to enable, see \ref _MALI_PERFORMANCE_COUNTER_FLAG_SRC0_ENABLE and related macro definitions */
+	u32 perf_counter_src0;              /**< [in] source id for performance counter 0 (see ARM DDI0415A, Table 3-60) */
+	u32 perf_counter_src1;              /**< [in] source id for performance counter 1 (see ARM DDI0415A, Table 3-60) */
+	u32 frame_builder_id;               /**< [in] id of the originating frame builder */
+	u32 flush_id;                       /**< [in] flush id within the originating frame builder */
+	_mali_uk_fence_t fence;             /**< [in] fence this job must wait on */
+	u64 timeline_point_ptr;            /**< [in,out] pointer to u32: location where point on gp timeline for this job will be written */
+	u32 varying_memsize;            /** < [in] size of varying memory to use deffer bind*/
+	u32 deferred_mem_num;
+	u64 deferred_mem_list;         /** < [in] memory hanlde list of varying buffer to use deffer bind */
+} _mali_uk_gp_start_job_s;
+
+#define _MALI_PERFORMANCE_COUNTER_FLAG_SRC0_ENABLE (1<<0) /**< Enable performance counter SRC0 for a job */
+#define _MALI_PERFORMANCE_COUNTER_FLAG_SRC1_ENABLE (1<<1) /**< Enable performance counter SRC1 for a job */
+#define _MALI_PERFORMANCE_COUNTER_FLAG_HEATMAP_ENABLE (1<<2) /**< Enable per tile (aka heatmap) generation with for a job (using the enabled counter sources) */
+
+/** @} */ /* end group _mali_uk_gpstartjob_s */
+
+typedef struct {
+	u64 user_job_ptr;               /**< [out] identifier for the job in user space */
+	_mali_uk_job_status status;     /**< [out] status of finished job */
+	u32 heap_current_addr;          /**< [out] value of the GP PLB PL heap start address register */
+	u32 perf_counter0;              /**< [out] value of performance counter 0 (see ARM DDI0415A) */
+	u32 perf_counter1;              /**< [out] value of performance counter 1 (see ARM DDI0415A) */
+	u32 pending_big_job_num;
+} _mali_uk_gp_job_finished_s;
+
+typedef struct {
+	u64 user_job_ptr;                    /**< [out] identifier for the job in user space */
+	u32 cookie;                          /**< [out] identifier for the core in kernel space on which the job stalled */
+} _mali_uk_gp_job_suspended_s;
+
+/** @} */ /* end group _mali_uk_gp */
+
+
+/** @defgroup _mali_uk_pp U/K Fragment Processor
+ * @{ */
+
+#define _MALI_PP_MAX_SUB_JOBS 8
+
+#define _MALI_PP_MAX_FRAME_REGISTERS ((0x058/4)+1)
+
+#define _MALI_PP_MAX_WB_REGISTERS ((0x02C/4)+1)
+
+#define _MALI_DLBU_MAX_REGISTERS 4
+
+/** Flag for _mali_uk_pp_start_job_s */
+#define _MALI_PP_JOB_FLAG_NO_NOTIFICATION (1<<0)
+#define _MALI_PP_JOB_FLAG_IS_WINDOW_SURFACE (1<<1)
+#define _MALI_PP_JOB_FLAG_PROTECTED (1<<2)
+
+/** @defgroup _mali_uk_ppstartjob_s Fragment Processor Start Job
+ * @{ */
+
+/** @brief Arguments for _mali_ukk_pp_start_job()
+ *
+ * To start a Fragment Processor job
+ * - associate the request with a reference to a mali_pp_job by setting
+ * @c user_job_ptr to the address of the @c mali_pp_job of the job.
+ * - set @c priority to the priority of the mali_pp_job
+ * - specify a timeout for the job by setting @c watchdog_msecs to the number of
+ * milliseconds the job is allowed to run. Specifying a value of 0 selects the
+ * default timeout in use by the device driver.
+ * - copy the frame registers from the @c mali_pp_job into @c frame_registers.
+ * For MALI200 you also need to copy the write back 0,1 and 2 registers.
+ * - set the @c perf_counter_flag, @c perf_counter_src0 and @c perf_counter_src1 to zero
+ * for a non-instrumented build. For an instrumented build you can use up
+ * to two performance counters. Set the corresponding bit in @c perf_counter_flag
+ * to enable them. @c perf_counter_src0 and @c perf_counter_src1 specify
+ * the source of what needs to get counted (e.g. number of vertex loader
+ * cache hits). For source id values, see ARM DDI0415A, Table 3-60.
+ * - pass in the user-kernel context in @c ctx that was returned from _mali_ukk_open()
+ *
+ * When _mali_ukk_pp_start_job() returns @c _MALI_OSK_ERR_OK, @c status contains the
+ * result of the request (see \ref _mali_uk_start_job_status). If the job could
+ * not get started (@c _MALI_UK_START_JOB_NOT_STARTED_DO_REQUEUE) it should be
+ * tried again.
+ *
+ * After the job has started, _mali_wait_for_notification() will be notified
+ * when the job finished. The notification will contain a
+ * @c _mali_uk_pp_job_finished_s result. It contains the @c user_job_ptr
+ * identifier used to start the job with, the job @c status (see \ref _mali_uk_job_status),
+ * the number of milliseconds the job took to render, and values of core registers
+ * when the job finished (irq status, performance counters, renderer list
+ * address). A job has finished succesfully when its status is
+ * @c _MALI_UK_JOB_STATUS_FINISHED. If the hardware detected a timeout while rendering
+ * the job, or software detected the job is taking more than @c watchdog_msecs to
+ * complete, the status will indicate @c _MALI_UK_JOB_STATUS_HANG.
+ * If the hardware detected a bus error while accessing memory associated with the
+ * job, status will indicate @c _MALI_UK_JOB_STATUS_SEG_FAULT.
+ * status will indicate @c _MALI_UK_JOB_STATUS_NOT_STARTED if the driver had to
+ * stop the job but the job didn't start on the hardware yet, e.g. when the
+ * driver shutdown.
+ *
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u64 user_job_ptr;               /**< [in] identifier for the job in user space */
+	u32 priority;                   /**< [in] job priority. A lower number means higher priority */
+	u32 frame_registers[_MALI_PP_MAX_FRAME_REGISTERS];         /**< [in] core specific registers associated with first sub job, see ARM DDI0415A */
+	u32 frame_registers_addr_frame[_MALI_PP_MAX_SUB_JOBS - 1]; /**< [in] ADDR_FRAME registers for sub job 1-7 */
+	u32 frame_registers_addr_stack[_MALI_PP_MAX_SUB_JOBS - 1]; /**< [in] ADDR_STACK registers for sub job 1-7 */
+	u32 wb0_registers[_MALI_PP_MAX_WB_REGISTERS];
+	u32 wb1_registers[_MALI_PP_MAX_WB_REGISTERS];
+	u32 wb2_registers[_MALI_PP_MAX_WB_REGISTERS];
+	u32 dlbu_registers[_MALI_DLBU_MAX_REGISTERS]; /**< [in] Dynamic load balancing unit registers */
+	u32 num_cores;                      /**< [in] Number of cores to set up (valid range: 1-8(M450) or 4(M400)) */
+	u32 perf_counter_flag;              /**< [in] bitmask indicating which performance counters to enable, see \ref _MALI_PERFORMANCE_COUNTER_FLAG_SRC0_ENABLE and related macro definitions */
+	u32 perf_counter_src0;              /**< [in] source id for performance counter 0 (see ARM DDI0415A, Table 3-60) */
+	u32 perf_counter_src1;              /**< [in] source id for performance counter 1 (see ARM DDI0415A, Table 3-60) */
+	u32 frame_builder_id;               /**< [in] id of the originating frame builder */
+	u32 flush_id;                       /**< [in] flush id within the originating frame builder */
+	u32 flags;                          /**< [in] See _MALI_PP_JOB_FLAG_* for a list of avaiable flags */
+	u32 tilesx;                         /**< [in] number of tiles in the x direction (needed for heatmap generation */
+	u32 tilesy;                         /**< [in] number of tiles in y direction (needed for reading the heatmap memory) */
+	u32 heatmap_mem;                    /**< [in] memory address to store counter values per tile (aka heatmap) */
+	u32 num_memory_cookies;             /**< [in] number of memory cookies attached to job */
+	u64 memory_cookies;               /**< [in] pointer to array of u32 memory cookies attached to job */
+	_mali_uk_fence_t fence;             /**< [in] fence this job must wait on */
+	u64 timeline_point_ptr;           /**< [in,out] pointer to location of u32 where point on pp timeline for this job will be written */
+} _mali_uk_pp_start_job_s;
+
+typedef struct {
+	u64 ctx;       /**< [in,out] user-kernel context (trashed on output) */
+	u64 gp_args;   /**< [in,out] GP uk arguments (see _mali_uk_gp_start_job_s) */
+	u64 pp_args;   /**< [in,out] PP uk arguments (see _mali_uk_pp_start_job_s) */
+} _mali_uk_pp_and_gp_start_job_s;
+
+/** @} */ /* end group _mali_uk_ppstartjob_s */
+
+typedef struct {
+	u64 user_job_ptr;                          /**< [out] identifier for the job in user space */
+	_mali_uk_job_status status;                /**< [out] status of finished job */
+	u32 perf_counter0[_MALI_PP_MAX_SUB_JOBS];  /**< [out] value of perfomance counter 0 (see ARM DDI0415A), one for each sub job */
+	u32 perf_counter1[_MALI_PP_MAX_SUB_JOBS];  /**< [out] value of perfomance counter 1 (see ARM DDI0415A), one for each sub job */
+	u32 perf_counter_src0;
+	u32 perf_counter_src1;
+} _mali_uk_pp_job_finished_s;
+
+typedef struct {
+	u32 number_of_enabled_cores;               /**< [out] the new number of enabled cores */
+} _mali_uk_pp_num_cores_changed_s;
+
+
+
+/**
+ * Flags to indicate write-back units
+ */
+typedef enum {
+	_MALI_UK_PP_JOB_WB0 = 1,
+	_MALI_UK_PP_JOB_WB1 = 2,
+	_MALI_UK_PP_JOB_WB2 = 4,
+} _mali_uk_pp_job_wbx_flag;
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 fb_id;                      /**< [in] Frame builder ID of job to disable WB units for */
+	u32 wb0_memory;
+	u32 wb1_memory;
+	u32 wb2_memory;
+} _mali_uk_pp_disable_wb_s;
+
+
+/** @} */ /* end group _mali_uk_pp */
+
+/** @defgroup _mali_uk_soft_job U/K Soft Job
+ * @{ */
+
+typedef struct {
+	u64 ctx;                            /**< [in,out] user-kernel context (trashed on output) */
+	u64 user_job;                       /**< [in] identifier for the job in user space */
+	u64 job_id_ptr;                     /**< [in,out] pointer to location of u32 where job id will be written */
+	_mali_uk_fence_t fence;             /**< [in] fence this job must wait on */
+	u32 point;                          /**< [out] point on soft timeline for this job */
+	u32 type;                           /**< [in] type of soft job */
+} _mali_uk_soft_job_start_s;
+
+typedef struct {
+	u64 user_job;                       /**< [out] identifier for the job in user space */
+} _mali_uk_soft_job_activated_s;
+
+typedef struct {
+	u64 ctx;                          /**< [in,out] user-kernel context (trashed on output) */
+	u32 job_id;                         /**< [in] id for soft job */
+} _mali_uk_soft_job_signal_s;
+
+/** @} */ /* end group _mali_uk_soft_job */
+
+typedef struct {
+	u32 counter_id;
+	u32 key;
+	int enable;
+} _mali_uk_annotate_profiling_mem_counter_s;
+
+typedef struct {
+	u32 sampling_rate;
+	int enable;
+} _mali_uk_annotate_profiling_enable_s;
+
+
+/** @addtogroup _mali_uk_core U/K Core
+ * @{ */
+
+/** @defgroup _mali_uk_waitfornotification_s Wait For Notification
+ * @{ */
+
+/** @brief Notification type encodings
+ *
+ * Each Notification type is an ordered pair of (subsystem,id), and is unique.
+ *
+ * The encoding of subsystem,id into a 32-bit word is:
+ * encoding = (( subsystem << _MALI_NOTIFICATION_SUBSYSTEM_SHIFT ) & _MALI_NOTIFICATION_SUBSYSTEM_MASK)
+ *            | (( id <<  _MALI_NOTIFICATION_ID_SHIFT ) & _MALI_NOTIFICATION_ID_MASK)
+ *
+ * @see _mali_uk_wait_for_notification_s
+ */
+typedef enum {
+	/** core notifications */
+
+	_MALI_NOTIFICATION_CORE_SHUTDOWN_IN_PROGRESS = (_MALI_UK_CORE_SUBSYSTEM << 16) | 0x20,
+	_MALI_NOTIFICATION_APPLICATION_QUIT = (_MALI_UK_CORE_SUBSYSTEM << 16) | 0x40,
+	_MALI_NOTIFICATION_SETTINGS_CHANGED = (_MALI_UK_CORE_SUBSYSTEM << 16) | 0x80,
+	_MALI_NOTIFICATION_SOFT_ACTIVATED = (_MALI_UK_CORE_SUBSYSTEM << 16) | 0x100,
+
+	/** Fragment Processor notifications */
+
+	_MALI_NOTIFICATION_PP_FINISHED = (_MALI_UK_PP_SUBSYSTEM << 16) | 0x10,
+	_MALI_NOTIFICATION_PP_NUM_CORE_CHANGE = (_MALI_UK_PP_SUBSYSTEM << 16) | 0x20,
+
+	/** Vertex Processor notifications */
+
+	_MALI_NOTIFICATION_GP_FINISHED = (_MALI_UK_GP_SUBSYSTEM << 16) | 0x10,
+	_MALI_NOTIFICATION_GP_STALLED = (_MALI_UK_GP_SUBSYSTEM << 16) | 0x20,
+
+	/** Profiling notifications */
+	_MALI_NOTIFICATION_ANNOTATE_PROFILING_MEM_COUNTER = (_MALI_UK_PROFILING_SUBSYSTEM << 16) | 0x10,
+	_MALI_NOTIFICATION_ANNOTATE_PROFILING_ENABLE = (_MALI_UK_PROFILING_SUBSYSTEM << 16) | 0x20,
+} _mali_uk_notification_type;
+
+/** to assist in splitting up 32-bit notification value in subsystem and id value */
+#define _MALI_NOTIFICATION_SUBSYSTEM_MASK 0xFFFF0000
+#define _MALI_NOTIFICATION_SUBSYSTEM_SHIFT 16
+#define _MALI_NOTIFICATION_ID_MASK 0x0000FFFF
+#define _MALI_NOTIFICATION_ID_SHIFT 0
+
+
+/** @brief Enumeration of possible settings which match mali_setting_t in user space
+ *
+ *
+ */
+typedef enum {
+	_MALI_UK_USER_SETTING_SW_EVENTS_ENABLE = 0,
+	_MALI_UK_USER_SETTING_COLORBUFFER_CAPTURE_ENABLED,
+	_MALI_UK_USER_SETTING_DEPTHBUFFER_CAPTURE_ENABLED,
+	_MALI_UK_USER_SETTING_STENCILBUFFER_CAPTURE_ENABLED,
+	_MALI_UK_USER_SETTING_PER_TILE_COUNTERS_CAPTURE_ENABLED,
+	_MALI_UK_USER_SETTING_BUFFER_CAPTURE_COMPOSITOR,
+	_MALI_UK_USER_SETTING_BUFFER_CAPTURE_WINDOW,
+	_MALI_UK_USER_SETTING_BUFFER_CAPTURE_OTHER,
+	_MALI_UK_USER_SETTING_BUFFER_CAPTURE_N_FRAMES,
+	_MALI_UK_USER_SETTING_BUFFER_CAPTURE_RESIZE_FACTOR,
+	_MALI_UK_USER_SETTING_SW_COUNTER_ENABLED,
+	_MALI_UK_USER_SETTING_MAX,
+} _mali_uk_user_setting_t;
+
+/* See mali_user_settings_db.c */
+extern const char *_mali_uk_user_setting_descriptions[];
+#define _MALI_UK_USER_SETTING_DESCRIPTIONS \
+	{                                           \
+		"sw_events_enable",                 \
+		"colorbuffer_capture_enable",       \
+		"depthbuffer_capture_enable",       \
+		"stencilbuffer_capture_enable",     \
+		"per_tile_counters_enable",         \
+		"buffer_capture_compositor",        \
+		"buffer_capture_window",            \
+		"buffer_capture_other",             \
+		"buffer_capture_n_frames",          \
+		"buffer_capture_resize_factor",     \
+		"sw_counters_enable",               \
+	};
+
+/** @brief struct to hold the value to a particular setting as seen in the kernel space
+ */
+typedef struct {
+	_mali_uk_user_setting_t setting;
+	u32 value;
+} _mali_uk_settings_changed_s;
+
+/** @brief Arguments for _mali_ukk_wait_for_notification()
+ *
+ * On successful return from _mali_ukk_wait_for_notification(), the members of
+ * this structure will indicate the reason for notification.
+ *
+ * Specifically, the source of the notification can be identified by the
+ * subsystem and id fields of the mali_uk_notification_type in the code.type
+ * member. The type member is encoded in a way to divide up the types into a
+ * subsystem field, and a per-subsystem ID field. See
+ * _mali_uk_notification_type for more information.
+ *
+ * Interpreting the data union member depends on the notification type:
+ *
+ * - type == _MALI_NOTIFICATION_CORE_SHUTDOWN_IN_PROGRESS
+ *     - The kernel side is shutting down. No further
+ * _mali_uk_wait_for_notification() calls should be made.
+ *     - In this case, the value of the data union member is undefined.
+ *     - This is used to indicate to the user space client that it should close
+ * the connection to the Mali Device Driver.
+ * - type == _MALI_NOTIFICATION_PP_FINISHED
+ *    - The notification data is of type _mali_uk_pp_job_finished_s. It contains the user_job_ptr
+ * identifier used to start the job with, the job status, the number of milliseconds the job took to render,
+ * and values of core registers when the job finished (irq status, performance counters, renderer list
+ * address).
+ *    - A job has finished succesfully when its status member is _MALI_UK_JOB_STATUS_FINISHED.
+ *    - If the hardware detected a timeout while rendering the job, or software detected the job is
+ * taking more than watchdog_msecs (see _mali_ukk_pp_start_job()) to complete, the status member will
+ * indicate _MALI_UK_JOB_STATUS_HANG.
+ *    - If the hardware detected a bus error while accessing memory associated with the job, status will
+ * indicate _MALI_UK_JOB_STATUS_SEG_FAULT.
+ *    - Status will indicate MALI_UK_JOB_STATUS_NOT_STARTED if the driver had to stop the job but the job
+ * didn't start the hardware yet, e.g. when the driver closes.
+ * - type == _MALI_NOTIFICATION_GP_FINISHED
+ *     - The notification data is of type _mali_uk_gp_job_finished_s. The notification is similar to that of
+ * type == _MALI_NOTIFICATION_PP_FINISHED, except that several other GP core register values are returned.
+ * The status values have the same meaning for type == _MALI_NOTIFICATION_PP_FINISHED.
+ * - type == _MALI_NOTIFICATION_GP_STALLED
+ *     - The nofication data is of type _mali_uk_gp_job_suspended_s. It contains the user_job_ptr
+ * identifier used to start the job with, the reason why the job stalled and a cookie to identify the core on
+ * which the job stalled.
+ *     - The reason member of gp_job_suspended is set to _MALIGP_JOB_SUSPENDED_OUT_OF_MEMORY
+ * when the polygon list builder unit has run out of memory.
+ */
+typedef struct {
+	u64 ctx;                       /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_notification_type type; /**< [out] Type of notification available */
+	union {
+		_mali_uk_gp_job_suspended_s gp_job_suspended;/**< [out] Notification data for _MALI_NOTIFICATION_GP_STALLED notification type */
+		_mali_uk_gp_job_finished_s  gp_job_finished; /**< [out] Notification data for _MALI_NOTIFICATION_GP_FINISHED notification type */
+		_mali_uk_pp_job_finished_s  pp_job_finished; /**< [out] Notification data for _MALI_NOTIFICATION_PP_FINISHED notification type */
+		_mali_uk_settings_changed_s setting_changed;/**< [out] Notification data for _MALI_NOTIFICAATION_SETTINGS_CHANGED notification type */
+		_mali_uk_soft_job_activated_s soft_job_activated; /**< [out] Notification data for _MALI_NOTIFICATION_SOFT_ACTIVATED notification type */
+		_mali_uk_annotate_profiling_mem_counter_s profiling_mem_counter;
+		_mali_uk_annotate_profiling_enable_s profiling_enable;
+	} data;
+} _mali_uk_wait_for_notification_s;
+
+/** @brief Arguments for _mali_ukk_post_notification()
+ *
+ * Posts the specified notification to the notification queue for this application.
+ * This is used to send a quit message to the callback thread.
+ */
+typedef struct {
+	u64 ctx;                       /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_notification_type type; /**< [in] Type of notification to post */
+} _mali_uk_post_notification_s;
+
+/** @} */ /* end group _mali_uk_waitfornotification_s */
+
+/** @defgroup _mali_uk_getapiversion_s Get API Version
+ * @{ */
+
+/** helpers for Device Driver API version handling */
+
+/** @brief Encode a version ID from a 16-bit input
+ *
+ * @note the input is assumed to be 16 bits. It must not exceed 16 bits. */
+#define _MAKE_VERSION_ID(x) (((x) << 16UL) | (x))
+
+/** @brief Check whether a 32-bit value is likely to be Device Driver API
+ * version ID. */
+#define _IS_VERSION_ID(x) (((x) & 0xFFFF) == (((x) >> 16UL) & 0xFFFF))
+
+/** @brief Decode a 16-bit version number from a 32-bit Device Driver API version
+ * ID */
+#define _GET_VERSION(x) (((x) >> 16UL) & 0xFFFF)
+
+/** @brief Determine whether two 32-bit encoded version IDs match */
+#define _IS_API_MATCH(x, y) (IS_VERSION_ID((x)) && IS_VERSION_ID((y)) && (GET_VERSION((x)) == GET_VERSION((y))))
+
+/**
+ * API version define.
+ * Indicates the version of the kernel API
+ * The version is a 16bit integer incremented on each API change.
+ * The 16bit integer is stored twice in a 32bit integer
+ * For example, for version 1 the value would be 0x00010001
+ */
+#define _MALI_API_VERSION 900
+#define _MALI_UK_API_VERSION _MAKE_VERSION_ID(_MALI_API_VERSION)
+
+/**
+ * The API version is a 16-bit integer stored in both the lower and upper 16-bits
+ * of a 32-bit value. The 16-bit API version value is incremented on each API
+ * change. Version 1 would be 0x00010001. Used in _mali_uk_get_api_version_s.
+ */
+typedef u32 _mali_uk_api_version;
+
+/** @brief Arguments for _mali_uk_get_api_version()
+ *
+ * The user-side interface version must be written into the version member,
+ * encoded using _MAKE_VERSION_ID(). It will be compared to the API version of
+ * the kernel-side interface.
+ *
+ * On successful return, the version member will be the API version of the
+ * kernel-side interface. _MALI_UK_API_VERSION macro defines the current version
+ * of the API.
+ *
+ * The compatible member must be checked to see if the version of the user-side
+ * interface is compatible with the kernel-side interface, since future versions
+ * of the interface may be backwards compatible.
+ */
+typedef struct {
+	u32 ctx;                        /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_api_version version;   /**< [in,out] API version of user-side interface. */
+	int compatible;                 /**< [out] @c 1 when @version is compatible, @c 0 otherwise */
+} _mali_uk_get_api_version_s;
+
+/** @brief Arguments for _mali_uk_get_api_version_v2()
+ *
+ * The user-side interface version must be written into the version member,
+ * encoded using _MAKE_VERSION_ID(). It will be compared to the API version of
+ * the kernel-side interface.
+ *
+ * On successful return, the version member will be the API version of the
+ * kernel-side interface. _MALI_UK_API_VERSION macro defines the current version
+ * of the API.
+ *
+ * The compatible member must be checked to see if the version of the user-side
+ * interface is compatible with the kernel-side interface, since future versions
+ * of the interface may be backwards compatible.
+ */
+typedef struct {
+	u64 ctx;                        /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_api_version version;   /**< [in,out] API version of user-side interface. */
+	int compatible;                 /**< [out] @c 1 when @version is compatible, @c 0 otherwise */
+} _mali_uk_get_api_version_v2_s;
+
+/** @} */ /* end group _mali_uk_getapiversion_s */
+
+/** @defgroup _mali_uk_get_user_settings_s Get user space settings */
+
+/** @brief struct to keep the matching values of the user space settings within certain context
+ *
+ * Each member of the settings array corresponds to a matching setting in the user space and its value is the value
+ * of that particular setting.
+ *
+ * All settings are given reference to the context pointed to by the ctx pointer.
+ *
+ */
+typedef struct {
+	u64 ctx;                       /**< [in,out] user-kernel context (trashed on output) */
+	u32 settings[_MALI_UK_USER_SETTING_MAX]; /**< [out] The values for all settings */
+} _mali_uk_get_user_settings_s;
+
+/** @brief struct to hold the value of a particular setting from the user space within a given context
+ */
+typedef struct {
+	u64 ctx;                       /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_user_setting_t setting; /**< [in] setting to get */
+	u32 value;                       /**< [out] value of setting */
+} _mali_uk_get_user_setting_s;
+
+/** @brief Arguments for _mali_ukk_request_high_priority() */
+typedef struct {
+	u64 ctx;                       /**< [in,out] user-kernel context (trashed on output) */
+} _mali_uk_request_high_priority_s;
+
+/** @brief Arguments for _mali_ukk_pending_submit() */
+typedef struct {
+	u64 ctx;                       /**< [in,out] user-kernel context (trashed on output) */
+} _mali_uk_pending_submit_s;
+
+/** @} */ /* end group _mali_uk_core */
+
+
+/** @defgroup _mali_uk_memory U/K Memory
+ * @{ */
+
+#define _MALI_MEMORY_ALLOCATE_RESIZEABLE  (1<<4) /* BUFFER can trim dow/grow*/
+#define _MALI_MEMORY_ALLOCATE_NO_BIND_GPU (1<<5) /*Not map to GPU when allocate, must call bind later*/
+#define _MALI_MEMORY_ALLOCATE_SWAPPABLE   (1<<6) /* Allocate swappale memory. */
+#define _MALI_MEMORY_ALLOCATE_DEFER_BIND (1<<7) /*Not map to GPU when allocate, must call bind later*/
+#define _MALI_MEMORY_ALLOCATE_SECURE (1<<8) /* Allocate secure memory. */
+
+
+typedef struct {
+	u64 ctx;                                          /**< [in,out] user-kernel context (trashed on output) */
+	u32 gpu_vaddr;                                    /**< [in] GPU virtual address */
+	u32 vsize;                                        /**< [in] vitrual size of the allocation */
+	u32 psize;                                        /**< [in] physical size of the allocation */
+	u32 flags;
+	u64 backend_handle;                               /**< [out] backend handle */
+	s32 secure_shared_fd;                           /** < [in] the mem handle for secure mem */
+} _mali_uk_alloc_mem_s;
+
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 gpu_vaddr;                /**< [in] use as handle to free allocation */
+	u32 free_pages_nr;      /** < [out] record the number of free pages */
+} _mali_uk_free_mem_s;
+
+
+#define _MALI_MEMORY_BIND_BACKEND_UMP             (1<<8)
+#define _MALI_MEMORY_BIND_BACKEND_DMA_BUF         (1<<9)
+#define _MALI_MEMORY_BIND_BACKEND_MALI_MEMORY     (1<<10)
+#define _MALI_MEMORY_BIND_BACKEND_EXTERNAL_MEMORY (1<<11)
+#define _MALI_MEMORY_BIND_BACKEND_EXT_COW         (1<<12)
+#define _MALI_MEMORY_BIND_BACKEND_HAVE_ALLOCATION (1<<13)
+
+
+#define _MALI_MEMORY_BIND_BACKEND_MASK (_MALI_MEMORY_BIND_BACKEND_UMP| \
+					_MALI_MEMORY_BIND_BACKEND_DMA_BUF |\
+					_MALI_MEMORY_BIND_BACKEND_MALI_MEMORY |\
+					_MALI_MEMORY_BIND_BACKEND_EXTERNAL_MEMORY |\
+					_MALI_MEMORY_BIND_BACKEND_EXT_COW |\
+					_MALI_MEMORY_BIND_BACKEND_HAVE_ALLOCATION)
+
+
+#define _MALI_MEMORY_GPU_READ_ALLOCATE            (1<<16)
+
+
+typedef struct {
+	u64 ctx;                                        /**< [in,out] user-kernel context (trashed on output) */
+	u32 vaddr;                                      /**< [in] mali address to map the physical memory to */
+	u32 size;                                       /**< [in] size */
+	u32 flags;                                      /**< [in] see_MALI_MEMORY_BIND_BACKEND_* */
+	u32 padding;                                    /** padding for 32/64 struct alignment */
+	union {
+		struct {
+			u32 secure_id;                  /**< [in] secure id */
+			u32 rights;                     /**< [in] rights necessary for accessing memory */
+			u32 flags;                      /**< [in] flags, see \ref _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE */
+		} bind_ump;
+		struct {
+			u32 mem_fd;                     /**< [in] Memory descriptor */
+			u32 rights;                     /**< [in] rights necessary for accessing memory */
+			u32 flags;                      /**< [in] flags, see \ref _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE */
+		} bind_dma_buf;
+		struct {
+			u32 phys_addr;                  /**< [in] physical address */
+			u32 rights;                     /**< [in] rights necessary for accessing memory */
+			u32 flags;                      /**< [in] flags, see \ref _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE */
+		} bind_ext_memory;
+	} mem_union;
+} _mali_uk_bind_mem_s;
+
+typedef struct {
+	u64 ctx;                                        /**< [in,out] user-kernel context (trashed on output) */
+	u32 flags;                                      /**< [in] see_MALI_MEMORY_BIND_BACKEND_* */
+	u32 vaddr;                                      /**<  [in] identifier for mapped memory object in kernel space  */
+} _mali_uk_unbind_mem_s;
+
+typedef struct {
+	u64 ctx;                                        /**< [in,out] user-kernel context (trashed on output) */
+	u32 target_handle;                              /**< [in] handle of allocation need to do COW */
+	u32 target_offset;                              /**< [in] offset in target allocation to do COW(for support COW  a memory allocated from memory_bank, PAGE_SIZE align)*/
+	u32 target_size;                                /**< [in] size of target allocation to do COW (for support memory bank, PAGE_SIZE align)(in byte) */
+	u32 range_start;                                /**< [in] re allocate range start offset, offset from the start of allocation (PAGE_SIZE align)*/
+	u32 range_size;                                 /**< [in] re allocate size (PAGE_SIZE align)*/
+	u32 vaddr;                                      /**< [in] mali address for the new allocaiton */
+	u32 backend_handle;                             /**< [out] backend handle */
+	u32 flags;
+} _mali_uk_cow_mem_s;
+
+typedef struct {
+	u64 ctx;                                        /**< [in,out] user-kernel context (trashed on output) */
+	u32 range_start;                                /**< [in] re allocate range start offset, offset from the start of allocation */
+	u32 size;                                       /**< [in] re allocate size*/
+	u32 vaddr;                                      /**< [in] mali address for the new allocaiton */
+	s32 change_pages_nr;                            /**< [out] record the page number change for cow operation */
+} _mali_uk_cow_modify_range_s;
+
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 mem_fd;                     /**< [in] Memory descriptor */
+	u32 size;                       /**< [out] size */
+} _mali_uk_dma_buf_get_size_s;
+
+/** Flag for _mali_uk_map_external_mem_s, _mali_uk_attach_ump_mem_s and _mali_uk_attach_dma_buf_s */
+#define _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE (1<<0)
+
+
+typedef struct {
+	u64 ctx;                                /**< [in,out] user-kernel context (trashed on output) */
+	u64 vaddr;                              /* the buffer to do resize*/
+	u32 psize;                              /* wanted physical size of this memory */
+} _mali_uk_mem_resize_s;
+
+/**
+ * @brief Arguments for _mali_uk[uk]_mem_write_safe()
+ */
+typedef struct {
+	u64 ctx;  /**< [in,out] user-kernel context (trashed on output) */
+	u64 src;  /**< [in] Pointer to source data */
+	u64 dest; /**< [in] Destination Mali buffer */
+	u32 size;   /**< [in,out] Number of bytes to write/copy on input, number of bytes actually written/copied on output */
+} _mali_uk_mem_write_safe_s;
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 size;                       /**< [out] size of MMU page table information (registers + page tables) */
+} _mali_uk_query_mmu_page_table_dump_size_s;
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 size;                       /**< [in] size of buffer to receive mmu page table information */
+	u64 buffer;                   /**< [in,out] buffer to receive mmu page table information */
+	u32 register_writes_size;       /**< [out] size of MMU register dump */
+	u64 register_writes;           /**< [out] pointer within buffer where MMU register dump is stored */
+	u32 page_table_dump_size;       /**< [out] size of MMU page table dump */
+	u64 page_table_dump;           /**< [out] pointer within buffer where MMU page table dump is stored */
+} _mali_uk_dump_mmu_page_table_s;
+
+/** @} */ /* end group _mali_uk_memory */
+
+
+/** @addtogroup _mali_uk_pp U/K Fragment Processor
+ * @{ */
+
+/** @brief Arguments for _mali_ukk_get_pp_number_of_cores()
+ *
+ * - pass in the user-kernel context @c ctx that was returned from _mali_ukk_open()
+ * - Upon successful return from _mali_ukk_get_pp_number_of_cores(), @c number_of_cores
+ * will contain the number of Fragment Processor cores in the system.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 number_of_total_cores;      /**< [out] Total number of Fragment Processor cores in the system */
+	u32 number_of_enabled_cores;    /**< [out] Number of enabled Fragment Processor cores */
+} _mali_uk_get_pp_number_of_cores_s;
+
+/** @brief Arguments for _mali_ukk_get_pp_core_version()
+ *
+ * - pass in the user-kernel context @c ctx that was returned from _mali_ukk_open()
+ * - Upon successful return from _mali_ukk_get_pp_core_version(), @c version contains
+ * the version that all Fragment Processor cores are compatible with.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	_mali_core_version version;     /**< [out] version returned from core, see \ref _mali_core_version  */
+	u32 padding;
+} _mali_uk_get_pp_core_version_s;
+
+/** @} */ /* end group _mali_uk_pp */
+
+
+/** @addtogroup _mali_uk_gp U/K Vertex Processor
+ * @{ */
+
+/** @brief Arguments for _mali_ukk_get_gp_number_of_cores()
+ *
+ * - pass in the user-kernel context @c ctx that was returned from _mali_ukk_open()
+ * - Upon successful return from _mali_ukk_get_gp_number_of_cores(), @c number_of_cores
+ * will contain the number of Vertex Processor cores in the system.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 number_of_cores;            /**< [out] number of Vertex Processor cores in the system */
+} _mali_uk_get_gp_number_of_cores_s;
+
+/** @brief Arguments for _mali_ukk_get_gp_core_version()
+ *
+ * - pass in the user-kernel context @c ctx that was returned from _mali_ukk_open()
+ * - Upon successful return from _mali_ukk_get_gp_core_version(), @c version contains
+ * the version that all Vertex Processor cores are compatible with.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	_mali_core_version version;     /**< [out] version returned from core, see \ref _mali_core_version */
+} _mali_uk_get_gp_core_version_s;
+
+/** @} */ /* end group _mali_uk_gp */
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 event_id;                   /**< [in] event id to register (see  enum mali_profiling_events for values) */
+	u32 data[5];                    /**< [in] event specific data */
+} _mali_uk_profiling_add_event_s;
+
+typedef struct {
+	u64 ctx;                     /**< [in,out] user-kernel context (trashed on output) */
+	u32 memory_usage;              /**< [out] total memory usage */
+	u32 vaddr;                                      /**< [in] mali address for the cow allocaiton */
+	s32 change_pages_nr;            /**< [out] record the page number change for cow operation */
+} _mali_uk_profiling_memory_usage_get_s;
+
+
+/** @addtogroup _mali_uk_memory U/K Memory
+ * @{ */
+
+/** @brief Arguments to _mali_ukk_mem_mmap()
+ *
+ * Use of the phys_addr member depends on whether the driver is compiled for
+ * Mali-MMU or nonMMU:
+ * - in the nonMMU case, this is the physical address of the memory as seen by
+ * the CPU (which may be a constant offset from that used by Mali)
+ * - in the MMU case, this is the Mali Virtual base address of the memory to
+ * allocate, and the particular physical pages used to back the memory are
+ * entirely determined by _mali_ukk_mem_mmap(). The details of the physical pages
+ * are not reported to user-space for security reasons.
+ *
+ * The cookie member must be stored for use later when freeing the memory by
+ * calling _mali_ukk_mem_munmap(). In the Mali-MMU case, the cookie is secure.
+ *
+ * The ukk_private word must be set to zero when calling from user-space. On
+ * Kernel-side, the  OS implementation of the U/K interface can use it to
+ * communicate data to the OS implementation of the OSK layer. In particular,
+ * _mali_ukk_get_big_block() directly calls _mali_ukk_mem_mmap directly, and
+ * will communicate its own ukk_private word through the ukk_private member
+ * here. The common code itself will not inspect or modify the ukk_private
+ * word, and so it may be safely used for whatever purposes necessary to
+ * integrate Mali Memory handling into the OS.
+ *
+ * The uku_private member is currently reserved for use by the user-side
+ * implementation of the U/K interface. Its value must be zero.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	void *mapping;                  /**< [out] Returns user-space virtual address for the mapping */
+	u32 size;                       /**< [in] Size of the requested mapping */
+	u32 phys_addr;                  /**< [in] Physical address - could be offset, depending on caller+callee convention */
+	mali_bool writeable;
+} _mali_uk_mem_mmap_s;
+
+/** @brief Arguments to _mali_ukk_mem_munmap()
+ *
+ * The cookie and mapping members must be that returned from the same previous
+ * call to _mali_ukk_mem_mmap(). The size member must correspond to cookie
+ * and mapping - that is, it must be the value originally supplied to a call to
+ * _mali_ukk_mem_mmap that returned the values of mapping and cookie.
+ *
+ * An error will be returned if an attempt is made to unmap only part of the
+ * originally obtained range, or to unmap more than was originally obtained.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	void *mapping;                  /**< [in] The mapping returned from mmap call */
+	u32 size;                       /**< [in] The size passed to mmap call */
+} _mali_uk_mem_munmap_s;
+/** @} */ /* end group _mali_uk_memory */
+
+/** @defgroup _mali_uk_vsync U/K VSYNC Wait Reporting Module
+ * @{ */
+
+/** @brief VSYNC events
+ *
+ * These events are reported when DDK starts to wait for vsync and when the
+ * vsync has occured and the DDK can continue on the next frame.
+ */
+typedef enum _mali_uk_vsync_event {
+	_MALI_UK_VSYNC_EVENT_BEGIN_WAIT = 0,
+	_MALI_UK_VSYNC_EVENT_END_WAIT
+} _mali_uk_vsync_event;
+
+/** @brief Arguments to _mali_ukk_vsync_event()
+ *
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_vsync_event event;     /**< [in] VSYNCH event type */
+} _mali_uk_vsync_event_report_s;
+
+/** @} */ /* end group _mali_uk_vsync */
+
+/** @defgroup _mali_uk_sw_counters_report U/K Software Counter Reporting
+ * @{ */
+
+/** @brief Software counter values
+ *
+ * Values recorded for each of the software counters during a single renderpass.
+ */
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u64 counters;                  /**< [in] The array of u32 counter values */
+	u32 num_counters;              /**< [in] The number of elements in counters array */
+} _mali_uk_sw_counters_report_s;
+
+/** @} */ /* end group _mali_uk_sw_counters_report */
+
+/** @defgroup _mali_uk_timeline U/K Mali Timeline
+ * @{ */
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	u32 timeline;                   /**< [in] timeline id */
+	u32 point;                      /**< [out] latest point on timeline */
+} _mali_uk_timeline_get_latest_point_s;
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_fence_t fence;         /**< [in] fence */
+	u32 timeout;                    /**< [in] timeout (0 for no wait, -1 for blocking) */
+	u32 status;                     /**< [out] status of fence (1 if signaled, 0 if timeout) */
+} _mali_uk_timeline_wait_s;
+
+typedef struct {
+	u64 ctx;                      /**< [in,out] user-kernel context (trashed on output) */
+	_mali_uk_fence_t fence;         /**< [in] mali fence to create linux sync fence from */
+	s32 sync_fd;                    /**< [out] file descriptor for new linux sync fence */
+} _mali_uk_timeline_create_sync_fence_s;
+
+/** @} */ /* end group _mali_uk_timeline */
+
+/** @} */ /* end group u_k_api */
+
+/** @} */ /* end group uddapi */
+
+typedef struct {
+	u64 ctx;                 /**< [in,out] user-kernel context (trashed on output) */
+	s32 stream_fd;   /**< [in] The profiling kernel base stream fd handle */
+} _mali_uk_profiling_stream_fd_get_s;
+
+typedef struct {
+	u64 ctx;        /**< [in,out] user-kernel context (trashed on output) */
+	u64 control_packet_data; /**< [in] the control packet data for control settings */
+	u32 control_packet_size;  /**< [in] The control packet size */
+	u64 response_packet_data; /** < [out] The response packet data */
+	u32 response_packet_size; /** < [in,out] The response packet data */
+} _mali_uk_profiling_control_set_s;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_UTGARD_UK_TYPES_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/license/gpl/mali_kernel_license.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/license/gpl/mali_kernel_license.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2010, 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_kernel_license.h
+ * Defines for the macro MODULE_LICENSE.
+ */
+
+#ifndef __MALI_KERNEL_LICENSE_H__
+#define __MALI_KERNEL_LICENSE_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#define MALI_KERNEL_LINUX_LICENSE     "GPL"
+#define MALI_LICENSE_IS_GPL 1
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_KERNEL_LICENSE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_devfreq.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_devfreq.c
@@ -0,0 +1,310 @@
+/*
+ * Copyright (C) 2011-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_osk_mali.h"
+#include "mali_kernel_common.h"
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/driver.h>
+#ifdef CONFIG_DEVFREQ_THERMAL
+#include <linux/devfreq_cooling.h>
+#endif
+
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 13, 0)
+#include <linux/pm_opp.h>
+#else /* Linux >= 3.13 */
+/* In 3.13 the OPP include header file, types, and functions were all
+ * renamed. Use the old filename for the include, and define the new names to
+ * the old, when an old kernel is detected.
+ */
+#include <linux/opp.h>
+#define dev_pm_opp opp
+#define dev_pm_opp_get_voltage opp_get_voltage
+#define dev_pm_opp_get_opp_count opp_get_opp_count
+#define dev_pm_opp_find_freq_ceil opp_find_freq_ceil
+#endif /* Linux >= 3.13 */
+
+#include "mali_pm_metrics.h"
+
+static int
+mali_devfreq_target(struct device *dev, unsigned long *target_freq, u32 flags)
+{
+	struct mali_device *mdev = dev_get_drvdata(dev);
+	struct dev_pm_opp *opp;
+	unsigned long freq = 0;
+	unsigned long voltage;
+	int err;
+
+	freq = *target_freq;
+
+	rcu_read_lock();
+	opp = devfreq_recommended_opp(dev, &freq, flags);
+	voltage = dev_pm_opp_get_voltage(opp);
+	rcu_read_unlock();
+	if (IS_ERR_OR_NULL(opp)) {
+		MALI_PRINT_ERROR(("Failed to get opp (%ld)\n", PTR_ERR(opp)));
+		return PTR_ERR(opp);
+	}
+
+	MALI_DEBUG_PRINT(2, ("mali_devfreq_target:set_freq = %lld flags = 0x%x\n", freq, flags));
+	/*
+	 * Only update if there is a change of frequency
+	 */
+	if (mdev->current_freq == freq) {
+		*target_freq = freq;
+		mali_pm_reset_dvfs_utilisation(mdev);
+		return 0;
+	}
+
+#ifdef CONFIG_REGULATOR
+	if (mdev->regulator && mdev->current_voltage != voltage
+	    && mdev->current_freq < freq) {
+		err = regulator_set_voltage(mdev->regulator, voltage, voltage);
+		if (err) {
+			MALI_PRINT_ERROR(("Failed to increase voltage (%d)\n", err));
+			return err;
+		}
+	}
+#endif
+
+	err = clk_set_rate(mdev->clock, freq);
+	if (err) {
+		MALI_PRINT_ERROR(("Failed to set clock %lu (target %lu)\n", freq, *target_freq));
+		return err;
+	}
+
+#ifdef CONFIG_REGULATOR
+	if (mdev->regulator && mdev->current_voltage != voltage
+	    && mdev->current_freq > freq) {
+		err = regulator_set_voltage(mdev->regulator, voltage, voltage);
+		if (err) {
+			MALI_PRINT_ERROR(("Failed to decrease voltage (%d)\n", err));
+			return err;
+		}
+	}
+#endif
+
+	*target_freq = freq;
+	mdev->current_voltage = voltage;
+	mdev->current_freq = freq;
+
+	mali_pm_reset_dvfs_utilisation(mdev);
+
+	return err;
+}
+
+static int
+mali_devfreq_cur_freq(struct device *dev, unsigned long *freq)
+{
+	struct mali_device *mdev = dev_get_drvdata(dev);
+
+	*freq = mdev->current_freq;
+
+	MALI_DEBUG_PRINT(2, ("mali_devfreq_cur_freq: freq = %d \n", *freq));
+	return 0;
+}
+
+static int
+mali_devfreq_status(struct device *dev, struct devfreq_dev_status *stat)
+{
+	struct mali_device *mdev = dev_get_drvdata(dev);
+
+	stat->current_frequency = mdev->current_freq;
+
+	mali_pm_get_dvfs_utilisation(mdev,
+				     &stat->total_time, &stat->busy_time);
+
+	stat->private_data = NULL;
+
+#ifdef CONFIG_DEVFREQ_THERMAL
+	memcpy(&mdev->devfreq->last_status, stat, sizeof(*stat));
+#endif
+
+	return 0;
+}
+
+/* setup platform specific opp in platform.c*/
+int __weak setup_opps(void)
+{
+	return 0;
+}
+
+/* term platform specific opp in platform.c*/
+int __weak term_opps(struct device *dev)
+{
+	return 0;
+}
+
+static int mali_devfreq_init_freq_table(struct mali_device *mdev,
+					struct devfreq_dev_profile *dp)
+{
+	int err, count;
+	int i = 0;
+	unsigned long freq = 0;
+	struct dev_pm_opp *opp;
+
+	err = setup_opps();
+	if (err)
+		return err;
+
+	rcu_read_lock();
+	count = dev_pm_opp_get_opp_count(mdev->dev);
+	if (count < 0) {
+		rcu_read_unlock();
+		return count;
+	}
+	rcu_read_unlock();
+
+	MALI_DEBUG_PRINT(2, ("mali devfreq table count %d\n", count));
+
+	dp->freq_table = kmalloc_array(count, sizeof(dp->freq_table[0]),
+				       GFP_KERNEL);
+	if (!dp->freq_table)
+		return -ENOMEM;
+
+	rcu_read_lock();
+	for (i = 0; i < count; i++, freq++) {
+		opp = dev_pm_opp_find_freq_ceil(mdev->dev, &freq);
+		if (IS_ERR(opp))
+			break;
+
+		dp->freq_table[i] = freq;
+		MALI_DEBUG_PRINT(2, ("mali devfreq table array[%d] = %d\n", i, freq));
+	}
+	rcu_read_unlock();
+
+	if (count != i)
+		MALI_PRINT_ERROR(("Unable to enumerate all OPPs (%d!=%d)\n",
+				  count, i));
+
+	dp->max_state = i;
+
+	return 0;
+}
+
+static void mali_devfreq_term_freq_table(struct mali_device *mdev)
+{
+	struct devfreq_dev_profile *dp = mdev->devfreq->profile;
+
+	kfree(dp->freq_table);
+	term_opps(mdev->dev);
+}
+
+static void mali_devfreq_exit(struct device *dev)
+{
+	struct mali_device *mdev = dev_get_drvdata(dev);
+
+	mali_devfreq_term_freq_table(mdev);
+}
+
+int mali_devfreq_init(struct mali_device *mdev)
+{
+#ifdef CONFIG_DEVFREQ_THERMAL
+	struct devfreq_cooling_power *callbacks = NULL;
+	_mali_osk_device_data data;
+#endif
+	struct devfreq_dev_profile *dp;
+	int err;
+
+	MALI_DEBUG_PRINT(2, ("Init Mali devfreq\n"));
+
+	if (!mdev->clock)
+		return -ENODEV;
+
+	mdev->current_freq = clk_get_rate(mdev->clock);
+
+	dp = &mdev->devfreq_profile;
+
+	dp->initial_freq = mdev->current_freq;
+	dp->polling_ms = 100;
+	dp->target = mali_devfreq_target;
+	dp->get_dev_status = mali_devfreq_status;
+	dp->get_cur_freq = mali_devfreq_cur_freq;
+	dp->exit = mali_devfreq_exit;
+
+	if (mali_devfreq_init_freq_table(mdev, dp))
+		return -EFAULT;
+
+	mdev->devfreq = devfreq_add_device(mdev->dev, dp,
+					   "simple_ondemand", NULL);
+	if (IS_ERR(mdev->devfreq)) {
+		mali_devfreq_term_freq_table(mdev);
+		return PTR_ERR(mdev->devfreq);
+	}
+
+	err = devfreq_register_opp_notifier(mdev->dev, mdev->devfreq);
+	if (err) {
+		MALI_PRINT_ERROR(("Failed to register OPP notifier (%d)\n", err));
+		goto opp_notifier_failed;
+	}
+
+#ifdef CONFIG_DEVFREQ_THERMAL
+	/* Initilization last_status it will be used when first power allocate called */
+	mdev->devfreq->last_status.current_frequency = mdev->current_freq;
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+		if (NULL != data.gpu_cooling_ops) {
+			callbacks = data.gpu_cooling_ops;
+			MALI_DEBUG_PRINT(2, ("Mali GPU Thermal: Callback handler installed \n"));
+		}
+	}
+
+	if (callbacks) {
+		mdev->devfreq_cooling = of_devfreq_cooling_register_power(
+						mdev->dev->of_node,
+						mdev->devfreq,
+						callbacks);
+		if (IS_ERR_OR_NULL(mdev->devfreq_cooling)) {
+			err = PTR_ERR(mdev->devfreq_cooling);
+			MALI_PRINT_ERROR(("Failed to register cooling device (%d)\n", err));
+			goto cooling_failed;
+		} else {
+			MALI_DEBUG_PRINT(2, ("Mali GPU Thermal Cooling installed \n"));
+		}
+	}
+#endif
+
+	return 0;
+
+#ifdef CONFIG_DEVFREQ_THERMAL
+cooling_failed:
+	devfreq_unregister_opp_notifier(mdev->dev, mdev->devfreq);
+#endif /* CONFIG_DEVFREQ_THERMAL */
+opp_notifier_failed:
+	err = devfreq_remove_device(mdev->devfreq);
+	if (err)
+		MALI_PRINT_ERROR(("Failed to terminate devfreq (%d)\n", err));
+	else
+		mdev->devfreq = NULL;
+
+	return err;
+}
+
+void mali_devfreq_term(struct mali_device *mdev)
+{
+	int err;
+
+	MALI_DEBUG_PRINT(2, ("Term Mali devfreq\n"));
+
+#ifdef CONFIG_DEVFREQ_THERMAL
+	devfreq_cooling_unregister(mdev->devfreq_cooling);
+#endif
+
+	devfreq_unregister_opp_notifier(mdev->dev, mdev->devfreq);
+
+	err = devfreq_remove_device(mdev->devfreq);
+	if (err)
+		MALI_PRINT_ERROR(("Failed to terminate devfreq (%d)\n", err));
+	else
+		mdev->devfreq = NULL;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_devfreq.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_devfreq.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2011-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#ifndef _MALI_DEVFREQ_H_
+#define _MALI_DEVFREQ_H_
+
+int mali_devfreq_init(struct mali_device *mdev);
+
+void mali_devfreq_term(struct mali_device *mdev);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_device_pause_resume.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_device_pause_resume.c
@@ -0,0 +1,36 @@
+/**
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_device_pause_resume.c
+ * Implementation of the Mali pause/resume functionality
+ */
+
+#include <linux/module.h>
+#include <linux/mali/mali_utgard.h>
+#include "mali_pm.h"
+
+void mali_dev_pause(void)
+{
+	/*
+	 * Deactive all groups to prevent hardware being touched
+	 * during the period of mali device pausing
+	 */
+	mali_pm_os_suspend(MALI_FALSE);
+}
+
+EXPORT_SYMBOL(mali_dev_pause);
+
+void mali_dev_resume(void)
+{
+	mali_pm_os_resume();
+}
+
+EXPORT_SYMBOL(mali_dev_resume);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_dma_fence.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_dma_fence.c
@@ -0,0 +1,439 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/version.h>
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 17, 0)
+#include "mali_dma_fence.h"
+#include <linux/atomic.h>
+#include <linux/workqueue.h>
+#endif
+
+static DEFINE_SPINLOCK(mali_dma_fence_lock);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static bool mali_dma_fence_enable_signaling(struct dma_fence *fence)
+{
+	MALI_IGNORE(fence);
+	return true;
+}
+
+static const char *mali_dma_fence_get_driver_name(struct dma_fence *fence)
+{
+	MALI_IGNORE(fence);
+	return "mali";
+}
+
+static const char *mali_dma_fence_get_timeline_name(struct dma_fence *fence)
+{
+	MALI_IGNORE(fence);
+	return "mali_dma_fence";
+}
+
+static const struct dma_fence_ops mali_dma_fence_ops = {
+	.get_driver_name = mali_dma_fence_get_driver_name,
+	.get_timeline_name = mali_dma_fence_get_timeline_name,
+	.enable_signaling = mali_dma_fence_enable_signaling,
+	.signaled = NULL,
+	.wait = dma_fence_default_wait,
+	.release = NULL
+};
+#else
+static bool mali_dma_fence_enable_signaling(struct fence *fence)
+{
+	MALI_IGNORE(fence);
+	return true;
+}
+
+static const char *mali_dma_fence_get_driver_name(struct fence *fence)
+{
+	MALI_IGNORE(fence);
+	return "mali";
+}
+
+static const char *mali_dma_fence_get_timeline_name(struct fence *fence)
+{
+	MALI_IGNORE(fence);
+	return "mali_dma_fence";
+}
+
+static const struct fence_ops mali_dma_fence_ops = {
+	.get_driver_name = mali_dma_fence_get_driver_name,
+	.get_timeline_name = mali_dma_fence_get_timeline_name,
+	.enable_signaling = mali_dma_fence_enable_signaling,
+	.signaled = NULL,
+	.wait = fence_default_wait,
+	.release = NULL
+};
+#endif
+
+static void mali_dma_fence_context_cleanup(struct mali_dma_fence_context *dma_fence_context)
+{
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+
+	for (i = 0; i < dma_fence_context->num_dma_fence_waiter; i++) {
+		if (dma_fence_context->mali_dma_fence_waiters[i]) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+			dma_fence_remove_callback(dma_fence_context->mali_dma_fence_waiters[i]->fence,
+						  &dma_fence_context->mali_dma_fence_waiters[i]->base);
+			dma_fence_put(dma_fence_context->mali_dma_fence_waiters[i]->fence);
+
+#else
+			fence_remove_callback(dma_fence_context->mali_dma_fence_waiters[i]->fence,
+					      &dma_fence_context->mali_dma_fence_waiters[i]->base);
+			fence_put(dma_fence_context->mali_dma_fence_waiters[i]->fence);
+#endif
+			kfree(dma_fence_context->mali_dma_fence_waiters[i]);
+			dma_fence_context->mali_dma_fence_waiters[i] = NULL;
+		}
+	}
+
+	if (NULL != dma_fence_context->mali_dma_fence_waiters)
+		kfree(dma_fence_context->mali_dma_fence_waiters);
+
+	dma_fence_context->mali_dma_fence_waiters = NULL;
+	dma_fence_context->num_dma_fence_waiter = 0;
+}
+
+static void mali_dma_fence_context_work_func(struct work_struct *work_handle)
+{
+	struct mali_dma_fence_context *dma_fence_context;
+
+	MALI_DEBUG_ASSERT_POINTER(work_handle);
+
+	dma_fence_context = container_of(work_handle, struct mali_dma_fence_context, work_handle);
+
+	dma_fence_context->cb_func(dma_fence_context->pp_job_ptr);
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static void mali_dma_fence_callback(struct dma_fence *fence, struct dma_fence_cb *cb)
+#else
+static void mali_dma_fence_callback(struct fence *fence, struct fence_cb *cb)
+#endif
+{
+	struct mali_dma_fence_waiter *dma_fence_waiter = NULL;
+	struct mali_dma_fence_context *dma_fence_context = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+	MALI_DEBUG_ASSERT_POINTER(cb);
+
+	MALI_IGNORE(fence);
+
+	dma_fence_waiter = container_of(cb, struct mali_dma_fence_waiter, base);
+	dma_fence_context = dma_fence_waiter->parent;
+
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+
+	if (atomic_dec_and_test(&dma_fence_context->count))
+		schedule_work(&dma_fence_context->work_handle);
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static _mali_osk_errcode_t mali_dma_fence_add_callback(struct mali_dma_fence_context *dma_fence_context, struct dma_fence *fence)
+#else
+static _mali_osk_errcode_t mali_dma_fence_add_callback(struct mali_dma_fence_context *dma_fence_context, struct fence *fence)
+#endif
+{
+	int ret = 0;
+	struct mali_dma_fence_waiter *dma_fence_waiter;
+	struct mali_dma_fence_waiter **dma_fence_waiters;
+
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	dma_fence_waiters = krealloc(dma_fence_context->mali_dma_fence_waiters,
+				     (dma_fence_context->num_dma_fence_waiter + 1)
+				     * sizeof(struct mali_dma_fence_waiter *),
+				     GFP_KERNEL);
+
+	if (NULL == dma_fence_waiters) {
+		MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to realloc the dma fence waiters.\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	dma_fence_context->mali_dma_fence_waiters = dma_fence_waiters;
+
+	dma_fence_waiter = kzalloc(sizeof(struct mali_dma_fence_waiter), GFP_KERNEL);
+
+	if (NULL == dma_fence_waiter) {
+		MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to create mali dma fence waiter.\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	dma_fence_get(fence);
+#else
+	fence_get(fence);
+#endif
+	dma_fence_waiter->fence = fence;
+	dma_fence_waiter->parent = dma_fence_context;
+	atomic_inc(&dma_fence_context->count);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	ret = dma_fence_add_callback(fence, &dma_fence_waiter->base,
+				     mali_dma_fence_callback);
+#else
+	ret = fence_add_callback(fence, &dma_fence_waiter->base,
+				 mali_dma_fence_callback);
+#endif
+	if (0 > ret) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+		dma_fence_put(fence);
+#else
+		fence_put(fence);
+#endif
+		kfree(dma_fence_waiter);
+		atomic_dec(&dma_fence_context->count);
+		if (-ENOENT == ret) {
+			/*-ENOENT if fence has already been signaled, return _MALI_OSK_ERR_OK*/
+			return _MALI_OSK_ERR_OK;
+		}
+		/* Failed to add the fence callback into fence, return _MALI_OSK_ERR_FAULT*/
+		MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to add callback into fence.\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	dma_fence_context->mali_dma_fence_waiters[dma_fence_context->num_dma_fence_waiter] = dma_fence_waiter;
+	dma_fence_context->num_dma_fence_waiter++;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+struct dma_fence *mali_dma_fence_new(u32  context, u32 seqno)
+#else
+struct fence *mali_dma_fence_new(u32  context, u32 seqno)
+#endif
+{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	struct dma_fence *fence = NULL;
+	fence = kzalloc(sizeof(struct dma_fence), GFP_KERNEL);
+#else
+	struct fence *fence = NULL;
+	fence = kzalloc(sizeof(struct fence), GFP_KERNEL);
+#endif
+	if (NULL == fence) {
+		MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to create dma fence.\n"));
+		return fence;
+	}
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	dma_fence_init(fence,
+		       &mali_dma_fence_ops,
+		       &mali_dma_fence_lock,
+		       context, seqno);
+#else
+	fence_init(fence,
+		   &mali_dma_fence_ops,
+		   &mali_dma_fence_lock,
+		   context, seqno);
+#endif
+	return fence;
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+void mali_dma_fence_signal_and_put(struct dma_fence **fence)
+#else
+void mali_dma_fence_signal_and_put(struct fence **fence)
+#endif
+{
+	MALI_DEBUG_ASSERT_POINTER(fence);
+	MALI_DEBUG_ASSERT_POINTER(*fence);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	dma_fence_signal(*fence);
+	dma_fence_put(*fence);
+#else
+	fence_signal(*fence);
+	fence_put(*fence);
+#endif
+	*fence = NULL;
+}
+
+void mali_dma_fence_context_init(struct mali_dma_fence_context *dma_fence_context,
+				 mali_dma_fence_context_callback_func_t  cb_func,
+				 void *pp_job_ptr)
+{
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+
+	INIT_WORK(&dma_fence_context->work_handle, mali_dma_fence_context_work_func);
+	atomic_set(&dma_fence_context->count, 1);
+	dma_fence_context->num_dma_fence_waiter = 0;
+	dma_fence_context->mali_dma_fence_waiters = NULL;
+	dma_fence_context->cb_func = cb_func;
+	dma_fence_context->pp_job_ptr = pp_job_ptr;
+}
+
+_mali_osk_errcode_t mali_dma_fence_context_add_waiters(struct mali_dma_fence_context *dma_fence_context,
+		struct reservation_object *dma_reservation_object)
+{
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_OK;
+	u32 shared_count = 0, i;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	struct dma_fence *exclusive_fence = NULL;
+	struct dma_fence **shared_fences = NULL;
+#else
+	struct fence *exclusive_fence = NULL;
+	struct fence **shared_fences = NULL;
+#endif
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+	MALI_DEBUG_ASSERT_POINTER(dma_reservation_object);
+
+	/* Get all the shared/exclusive fences in the reservation object of dma buf*/
+	ret = reservation_object_get_fences_rcu(dma_reservation_object, &exclusive_fence,
+						&shared_count, &shared_fences);
+	if (ret < 0) {
+		MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to get  shared or exclusive_fence dma fences from  the reservation object of dma buf.\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	if (exclusive_fence) {
+		ret = mali_dma_fence_add_callback(dma_fence_context, exclusive_fence);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to add callback into exclusive fence.\n"));
+			mali_dma_fence_context_cleanup(dma_fence_context);
+			goto ended;
+		}
+	}
+
+
+	for (i = 0; i < shared_count; i++) {
+		ret = mali_dma_fence_add_callback(dma_fence_context, shared_fences[i]);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to add callback into shared fence [%d].\n", i));
+			mali_dma_fence_context_cleanup(dma_fence_context);
+			break;
+		}
+	}
+
+ended:
+
+	if (exclusive_fence)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+		dma_fence_put(exclusive_fence);
+#else
+		fence_put(exclusive_fence);
+#endif
+
+	if (shared_fences) {
+		for (i = 0; i < shared_count; i++) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+			dma_fence_put(shared_fences[i]);
+#else
+			fence_put(shared_fences[i]);
+#endif
+		}
+		kfree(shared_fences);
+	}
+
+	return ret;
+}
+
+
+void mali_dma_fence_context_term(struct mali_dma_fence_context *dma_fence_context)
+{
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+	atomic_set(&dma_fence_context->count, 0);
+	if (dma_fence_context->work_handle.func) {
+		cancel_work_sync(&dma_fence_context->work_handle);
+	}
+	mali_dma_fence_context_cleanup(dma_fence_context);
+}
+
+void mali_dma_fence_context_dec_count(struct mali_dma_fence_context *dma_fence_context)
+{
+	MALI_DEBUG_ASSERT_POINTER(dma_fence_context);
+
+	if (atomic_dec_and_test(&dma_fence_context->count))
+		schedule_work(&dma_fence_context->work_handle);
+}
+
+
+void mali_dma_fence_add_reservation_object_list(struct reservation_object *dma_reservation_object,
+		struct reservation_object **dma_reservation_object_list,
+		u32 *num_dma_reservation_object)
+{
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(dma_reservation_object);
+	MALI_DEBUG_ASSERT_POINTER(dma_reservation_object_list);
+	MALI_DEBUG_ASSERT_POINTER(num_dma_reservation_object);
+
+	for (i = 0; i < *num_dma_reservation_object; i++) {
+		if (dma_reservation_object_list[i] == dma_reservation_object)
+			return;
+	}
+
+	dma_reservation_object_list[*num_dma_reservation_object] = dma_reservation_object;
+	(*num_dma_reservation_object)++;
+}
+
+int mali_dma_fence_lock_reservation_object_list(struct reservation_object **dma_reservation_object_list,
+		u32 num_dma_reservation_object, struct ww_acquire_ctx *ww_actx)
+{
+	u32 i;
+
+	struct reservation_object *reservation_object_to_slow_lock = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(dma_reservation_object_list);
+	MALI_DEBUG_ASSERT_POINTER(ww_actx);
+
+	ww_acquire_init(ww_actx, &reservation_ww_class);
+
+again:
+	for (i = 0; i < num_dma_reservation_object; i++) {
+		int ret;
+
+		if (dma_reservation_object_list[i] == reservation_object_to_slow_lock) {
+			reservation_object_to_slow_lock = NULL;
+			continue;
+		}
+
+		ret = ww_mutex_lock(&dma_reservation_object_list[i]->lock, ww_actx);
+
+		if (ret < 0) {
+			u32  slow_lock_index = i;
+
+			/* unlock all pre locks we have already locked.*/
+			while (i > 0) {
+				i--;
+				ww_mutex_unlock(&dma_reservation_object_list[i]->lock);
+			}
+
+			if (NULL != reservation_object_to_slow_lock)
+				ww_mutex_unlock(&reservation_object_to_slow_lock->lock);
+
+			if (ret == -EDEADLK) {
+				reservation_object_to_slow_lock = dma_reservation_object_list[slow_lock_index];
+				ww_mutex_lock_slow(&reservation_object_to_slow_lock->lock, ww_actx);
+				goto again;
+			}
+			ww_acquire_fini(ww_actx);
+			MALI_DEBUG_PRINT(1, ("Mali dma fence: failed to lock all dma reservation objects.\n", i));
+			return ret;
+		}
+	}
+
+	ww_acquire_done(ww_actx);
+	return 0;
+}
+
+void mali_dma_fence_unlock_reservation_object_list(struct reservation_object **dma_reservation_object_list,
+		u32 num_dma_reservation_object, struct ww_acquire_ctx *ww_actx)
+{
+	u32 i;
+
+	for (i = 0; i < num_dma_reservation_object; i++)
+		ww_mutex_unlock(&dma_reservation_object_list[i]->lock);
+
+	ww_acquire_fini(ww_actx);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_dma_fence.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_dma_fence.h
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_dma_fence.h
+ *
+ * Mali interface for Linux dma buf fence objects.
+ */
+
+#ifndef _MALI_DMA_FENCE_H_
+#define _MALI_DMA_FENCE_H_
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 17, 0)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+#include <linux/dma-fence.h>
+#else
+#include <linux/fence.h>
+#endif
+#include <linux/reservation.h>
+#endif
+
+struct mali_dma_fence_context;
+
+/* The mali dma fence context callback function */
+typedef void (*mali_dma_fence_context_callback_func_t)(void *pp_job_ptr);
+
+struct mali_dma_fence_waiter {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	struct dma_fence *fence;
+	struct dma_fence_cb base;
+#else
+	struct fence_cb base;
+	struct fence *fence;
+#endif
+	struct mali_dma_fence_context *parent;
+};
+
+struct mali_dma_fence_context {
+	struct work_struct work_handle;
+	struct mali_dma_fence_waiter **mali_dma_fence_waiters;
+	u32 num_dma_fence_waiter;
+	atomic_t count;
+	void *pp_job_ptr; /* the mali pp job pointer */;
+	mali_dma_fence_context_callback_func_t cb_func;
+};
+
+/* Create a dma fence
+ * @param context The execution context this fence is run on
+ * @param seqno A linearly increasing sequence number for this context
+ * @return the new dma fence if success, or NULL on failure.
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+struct dma_fence *mali_dma_fence_new(u32  context, u32 seqno);
+#else
+struct fence *mali_dma_fence_new(u32  context, u32 seqno);
+#endif
+/* Signal and put dma fence
+ * @param fence The dma fence to signal and put
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+void mali_dma_fence_signal_and_put(struct dma_fence **fence);
+#else
+void mali_dma_fence_signal_and_put(struct fence **fence);
+#endif
+/**
+ * Initialize a mali dma fence context for pp job.
+ * @param dma_fence_context The mali dma fence context to initialize.
+ * @param cb_func The dma fence context callback function to call when all dma fence release.
+ * @param pp_job_ptr The pp_job to call function with.
+ */
+void mali_dma_fence_context_init(struct mali_dma_fence_context *dma_fence_context,
+				 mali_dma_fence_context_callback_func_t  cb_func,
+				 void *pp_job_ptr);
+
+/**
+ * Add new mali dma fence waiter into mali dma fence context
+ * @param dma_fence_context The mali dma fence context
+ * @param dma_reservation_object the reservation object to create new mali dma fence waiters
+ * @return _MALI_OSK_ERR_OK if success, or not.
+ */
+_mali_osk_errcode_t mali_dma_fence_context_add_waiters(struct mali_dma_fence_context *dma_fence_context,
+		struct reservation_object *dma_reservation_object);
+
+/**
+ * Release the dma fence context
+ * @param dma_fence_text The mali dma fence context.
+ */
+void mali_dma_fence_context_term(struct mali_dma_fence_context *dma_fence_context);
+
+/**
+ * Decrease the dma fence context atomic count
+ * @param dma_fence_text The mali dma fence context.
+ */
+void mali_dma_fence_context_dec_count(struct mali_dma_fence_context *dma_fence_context);
+
+/**
+ * Get all reservation object
+ * @param dma_reservation_object The reservation object to add into the reservation object list
+ * @param dma_reservation_object_list The reservation object list to store all reservation object
+ * @param num_dma_reservation_object The number of all reservation object
+ */
+void mali_dma_fence_add_reservation_object_list(struct reservation_object *dma_reservation_object,
+		struct reservation_object **dma_reservation_object_list,
+		u32 *num_dma_reservation_object);
+
+/**
+ * Wait/wound mutex lock to lock all reservation object.
+ */
+int mali_dma_fence_lock_reservation_object_list(struct reservation_object **dma_reservation_object_list,
+		u32  num_dma_reservation_object, struct ww_acquire_ctx *ww_actx);
+
+/**
+ * Wait/wound mutex lock to unlock all reservation object.
+ */
+void mali_dma_fence_unlock_reservation_object_list(struct reservation_object **dma_reservation_object_list,
+		u32 num_dma_reservation_object, struct ww_acquire_ctx *ww_actx);
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_internal_sync.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_internal_sync.c
@@ -0,0 +1,783 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_internal_sync.h"
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 6, 0)
+#include <linux/ioctl.h>
+#include <linux/export.h>
+#include <linux/file.h>
+#include <linux/fs.h>
+#include <linux/kernel.h>
+#include <linux/poll.h>
+#include <linux/sched.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/anon_inodes.h>
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#if defined(DEBUG)
+#include "mali_session.h"
+#include "mali_timeline.h"
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static const struct dma_fence_ops fence_ops;
+#else
+static const struct fence_ops fence_ops;
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static struct mali_internal_sync_point *mali_internal_fence_to_sync_pt(struct dma_fence *fence)
+#else
+static struct mali_internal_sync_point *mali_internal_fence_to_sync_pt(struct fence *fence)
+#endif
+{
+	MALI_DEBUG_ASSERT_POINTER(fence);
+	return container_of(fence, struct mali_internal_sync_point, base);
+}
+
+static inline struct mali_internal_sync_timeline *mali_internal_sync_pt_to_sync_timeline(struct mali_internal_sync_point *sync_pt)
+{
+	MALI_DEBUG_ASSERT_POINTER(sync_pt);
+	return container_of(sync_pt->base.lock, struct mali_internal_sync_timeline, sync_pt_list_lock);
+}
+
+static void mali_internal_sync_timeline_free(struct kref *kref_count)
+{
+	struct mali_internal_sync_timeline *sync_timeline;
+
+	MALI_DEBUG_ASSERT_POINTER(kref_count);
+
+	sync_timeline = container_of(kref_count, struct mali_internal_sync_timeline, kref_count);
+
+	if (sync_timeline->ops->release_obj)
+		sync_timeline->ops->release_obj(sync_timeline);
+
+	kfree(sync_timeline);
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+static void mali_internal_fence_check_cb_func(struct fence *fence, struct fence_cb *cb)
+#else
+static void mali_internal_fence_check_cb_func(struct dma_fence *fence, struct dma_fence_cb *cb)
+#endif
+{
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+	struct mali_internal_sync_fence_cb *check;
+#else
+	struct mali_internal_sync_fence_waiter *waiter;
+#endif
+	struct mali_internal_sync_fence *sync_fence;
+	int ret;
+	MALI_DEBUG_ASSERT_POINTER(cb);
+	MALI_IGNORE(fence);
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+	check = container_of(cb, struct mali_internal_sync_fence_cb, cb);
+	sync_fence = check->sync_file;
+#else
+	waiter = container_of(cb, struct mali_internal_sync_fence_waiter, cb);
+	sync_fence = (struct mali_internal_sync_fence *)waiter->work.private;
+#endif
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+	ret = atomic_dec_and_test(&sync_fence->status);
+	if (ret)
+		wake_up_all(&sync_fence->wq);
+#else
+	ret = sync_fence->fence->ops->signaled(sync_fence->fence);
+
+	if (0 > ret)
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to wait fence  0x%x for sync_fence 0x%x.\n", fence, sync_fence));
+	if (1 == ret)
+		wake_up_all(&sync_fence->wq);
+#endif
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+static void mali_internal_sync_fence_add_fence(struct mali_internal_sync_fence *sync_fence, struct fence *sync_pt)
+{
+	int fence_num = 0;
+	MALI_DEBUG_ASSERT_POINTER(sync_fence);
+	MALI_DEBUG_ASSERT_POINTER(sync_pt);
+
+	fence_num = sync_fence->num_fences;
+
+	sync_fence->cbs[fence_num].fence = sync_pt;
+	sync_fence->cbs[fence_num].sync_file = sync_fence;
+
+	if (!fence_add_callback(sync_pt, &sync_fence->cbs[fence_num].cb, mali_internal_fence_check_cb_func)) {
+		fence_get(sync_pt);
+		sync_fence->num_fences++;
+		atomic_inc(&sync_fence->status);
+	}
+}
+#endif
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 13, 0)
+static int mali_internal_sync_fence_wake_up_wq(wait_queue_entry_t *curr, unsigned mode,
+		int wake_flags, void *key)
+#else
+static int mali_internal_sync_fence_wake_up_wq(wait_queue_t *curr, unsigned mode,
+		int wake_flags, void *key)
+#endif
+{
+	struct mali_internal_sync_fence_waiter *wait;
+	MALI_IGNORE(mode);
+	MALI_IGNORE(wake_flags);
+	MALI_IGNORE(key);
+
+	wait = container_of(curr, struct mali_internal_sync_fence_waiter, work);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 13, 0)
+	list_del_init(&wait->work.entry);
+#else
+	list_del_init(&wait->work.task_list);
+#endif
+	wait->callback(wait->work.private, wait);
+	return 1;
+}
+
+struct mali_internal_sync_timeline *mali_internal_sync_timeline_create(const struct mali_internal_sync_timeline_ops *ops,
+		int size, const char *name)
+{
+	struct mali_internal_sync_timeline *sync_timeline = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(ops);
+
+	if (size < sizeof(struct mali_internal_sync_timeline)) {
+		MALI_PRINT_ERROR(("Mali internal sync:Invalid size to create the mali internal sync timeline.\n"));
+		goto err;
+	}
+
+	sync_timeline = kzalloc(size, GFP_KERNEL);
+	if (NULL == sync_timeline) {
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to  allocate buffer  for the mali internal sync timeline.\n"));
+		goto err;
+	}
+	kref_init(&sync_timeline->kref_count);
+	sync_timeline->ops = ops;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	sync_timeline->fence_context = dma_fence_context_alloc(1);
+#else
+	sync_timeline->fence_context = fence_context_alloc(1);
+#endif
+	strlcpy(sync_timeline->name, name, sizeof(sync_timeline->name));
+
+	INIT_LIST_HEAD(&sync_timeline->sync_pt_list_head);
+	spin_lock_init(&sync_timeline->sync_pt_list_lock);
+
+	return sync_timeline;
+err:
+	if (NULL != sync_timeline) {
+		kfree(sync_timeline);
+	}
+	return NULL;
+}
+
+void mali_internal_sync_timeline_destroy(struct mali_internal_sync_timeline *sync_timeline)
+{
+	MALI_DEBUG_ASSERT_POINTER(sync_timeline);
+
+	sync_timeline->destroyed = MALI_TRUE;
+
+	smp_wmb();
+
+	mali_internal_sync_timeline_signal(sync_timeline);
+	kref_put(&sync_timeline->kref_count, mali_internal_sync_timeline_free);
+}
+
+void mali_internal_sync_timeline_signal(struct mali_internal_sync_timeline *sync_timeline)
+{
+	unsigned long flags;
+	struct mali_internal_sync_point *sync_pt, *next;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_timeline);
+
+	spin_lock_irqsave(&sync_timeline->sync_pt_list_lock, flags);
+
+	list_for_each_entry_safe(sync_pt, next, &sync_timeline->sync_pt_list_head,
+				 sync_pt_list) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+		if (dma_fence_is_signaled_locked(&sync_pt->base))
+#else
+		if (fence_is_signaled_locked(&sync_pt->base))
+#endif
+			list_del_init(&sync_pt->sync_pt_list);
+	}
+
+	spin_unlock_irqrestore(&sync_timeline->sync_pt_list_lock, flags);
+}
+
+struct mali_internal_sync_point *mali_internal_sync_point_create(struct mali_internal_sync_timeline *sync_timeline, int size)
+{
+	unsigned long flags;
+	struct mali_internal_sync_point *sync_pt = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_timeline);
+
+	if (size < sizeof(struct mali_internal_sync_point)) {
+		MALI_PRINT_ERROR(("Mali internal sync:Invalid size to create the mali internal sync point.\n"));
+		goto err;
+	}
+
+	sync_pt = kzalloc(size, GFP_KERNEL);
+	if (NULL == sync_pt) {
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to  allocate buffer  for the mali internal sync point.\n"));
+		goto err;
+	}
+	spin_lock_irqsave(&sync_timeline->sync_pt_list_lock, flags);
+	kref_get(&sync_timeline->kref_count);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	dma_fence_init(&sync_pt->base, &fence_ops, &sync_timeline->sync_pt_list_lock,
+		       sync_timeline->fence_context, ++sync_timeline->value);
+#else
+	fence_init(&sync_pt->base, &fence_ops, &sync_timeline->sync_pt_list_lock,
+		   sync_timeline->fence_context, ++sync_timeline->value);
+#endif
+	INIT_LIST_HEAD(&sync_pt->sync_pt_list);
+	spin_unlock_irqrestore(&sync_timeline->sync_pt_list_lock, flags);
+
+	return sync_pt;
+err:
+	if (NULL != sync_pt) {
+		kfree(sync_pt);
+	}
+	return NULL;
+}
+
+struct mali_internal_sync_fence *mali_internal_sync_fence_fdget(int fd)
+{
+	struct file *file = fget(fd);
+
+	if (NULL == file) {
+		return NULL;
+	}
+
+	return file->private_data;
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+struct mali_internal_sync_fence *mali_internal_sync_fence_merge(
+	struct mali_internal_sync_fence *sync_fence1, struct mali_internal_sync_fence *sync_fence2)
+{
+	struct mali_internal_sync_fence *new_sync_fence;
+	int i, j, num_fence1, num_fence2, total_fences;
+	struct fence *fence0 = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_fence1);
+	MALI_DEBUG_ASSERT_POINTER(sync_fence2);
+
+	num_fence1 = sync_fence1->num_fences;
+	num_fence2 = sync_fence2->num_fences;
+
+	total_fences = num_fence1 + num_fence2;
+
+	i = 0;
+	j = 0;
+
+	if (num_fence1 > 0) {
+		fence0 = sync_fence1->cbs[i].fence;
+		i = 1;
+	} else if (num_fence2 > 0) {
+		fence0 = sync_fence2->cbs[i].fence;
+		j = 1;
+	}
+
+	new_sync_fence = (struct mali_internal_sync_fence *)sync_file_create(fence0);
+	if (NULL == new_sync_fence) {
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to  create the mali internal sync fence when merging sync fence.\n"));
+		return NULL;
+	}
+
+	fence_remove_callback(new_sync_fence->cb[0].fence, &new_sync_fence->cb[0].cb);
+	new_sync_fence->num_fences = 0;
+	atomic_dec(&new_sync_fence->status);
+
+	for (; i < num_fence1 && j < num_fence2;) {
+		struct fence *fence1 = sync_fence1->cbs[i].fence;
+		struct fence *fence2 = sync_fence2->cbs[j].fence;
+
+		if (fence1->context < fence2->context) {
+			mali_internal_sync_fence_add_fence(new_sync_fence, fence1);
+
+			i++;
+		} else if (fence1->context > fence2->context) {
+			mali_internal_sync_fence_add_fence(new_sync_fence, fence2);
+
+			j++;
+		} else {
+			if (fence1->seqno - fence2->seqno <= INT_MAX)
+				mali_internal_sync_fence_add_fence(new_sync_fence, fence1);
+			else
+				mali_internal_sync_fence_add_fence(new_sync_fence, fence2);
+			i++;
+			j++;
+		}
+	}
+
+	for (; i < num_fence1; i++)
+		mali_internal_sync_fence_add_fence(new_sync_fence, sync_fence1->cbs[i].fence);
+
+	for (; j < num_fence2; j++)
+		mali_internal_sync_fence_add_fence(new_sync_fence, sync_fence2->cbs[j].fence);
+
+	return new_sync_fence;
+}
+#else
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+static struct fence **mali_internal_get_fences(struct mali_internal_sync_fence *sync_fence, int *num_fences)
+#else
+static struct dma_fence **mali_internal_get_fences(struct mali_internal_sync_fence *sync_fence, int *num_fences)
+#endif
+{
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	if (sync_fence->fence->ops == &fence_array_ops) {
+		struct fence_array *fence_array = container_of(sync_fence->fence, struct fence_array, base);
+		*num_fences = fence_array->num_fences;
+		return fence_array->fences;
+	}
+#else
+	if (sync_fence->fence->ops == &dma_fence_array_ops) {
+		struct dma_fence_array *fence_array = container_of(sync_fence->fence, struct dma_fence_array, base);
+		*num_fences = fence_array->num_fences;
+		return fence_array->fences;
+	}
+#endif
+	*num_fences = 1;
+	return &sync_fence->fence;
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+static void mali_internal_add_fence_array(struct fence **fences, int *num_fences, struct fence *fence)
+#else
+static void mali_internal_add_fence_array(struct dma_fence **fences, int *num_fences, struct dma_fence *fence)
+#endif
+{
+	fences[*num_fences] = fence;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	if (!fence_is_signaled(fence)) {
+		fence_get(fence);
+		(*num_fences)++;
+	}
+#else
+	if (!dma_fence_is_signaled(fence)) {
+		dma_fence_get(fence);
+		(*num_fences)++;
+	}
+#endif
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+static int mali_internal_sync_fence_set_fence_array(struct mali_internal_sync_fence *sync_fence,
+		struct fence **fences, int num_fences)
+#else
+static int mali_internal_sync_fence_set_fence_array(struct mali_internal_sync_fence *sync_fence,
+		struct dma_fence **fences, int num_fences)
+#endif
+{
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	struct fence_array *array;
+#else
+	struct dma_fence_array *array;
+#endif
+	if(num_fences == 1) {
+		sync_fence->fence =fences[0];
+		kfree(fences);
+	} else {	
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	array = fence_array_create(num_fences, fences,
+				   fence_context_alloc(1), 1, false);
+#else
+	array = dma_fence_array_create(num_fences, fences,
+				       dma_fence_context_alloc(1), 1, false);
+#endif
+	if (!array)
+		return -ENOMEM;
+
+		sync_fence->fence = &array->base;
+	}
+	return 0;
+}
+
+struct mali_internal_sync_fence *mali_internal_sync_fence_merge(
+	struct mali_internal_sync_fence *sync_fence1, struct mali_internal_sync_fence *sync_fence2)
+{
+	struct mali_internal_sync_fence *sync_fence;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	struct fence **fences, **nfences, **fences1, **fences2;
+#else
+	struct dma_fence **fences, **nfences, **fences1, **fences2;
+#endif
+	int real_num_fences, i, j, num_fences, num_fences1, num_fences2;
+
+	fences1 = mali_internal_get_fences(sync_fence1, &num_fences1);
+	fences2 = mali_internal_get_fences(sync_fence2, &num_fences2);
+
+	num_fences = num_fences1 + num_fences2;
+
+	fences = kcalloc(num_fences, sizeof(*fences), GFP_KERNEL);
+	if (!fences) {
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to  alloc buffer for fences.\n"));
+		goto fences_alloc_failed;
+	}
+
+	for (real_num_fences = i = j = 0; i < num_fences1 && j < num_fences2;) {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+		struct fence *fence1 = fences1[i];
+		struct fence *fence2 = fences2[j];
+#else
+		struct dma_fence *fence1 = fences1[i];
+		struct dma_fence *fence2 = fences2[j];
+#endif
+		if (fence1->context < fence2->context) {
+			mali_internal_add_fence_array(fences, &real_num_fences, fence1);
+
+			i++;
+		} else if (fence1->context > fence2->context) {
+			mali_internal_add_fence_array(fences, &real_num_fences, fence2);
+
+			j++;
+		} else {
+			if (fence1->seqno - fence2->seqno <= INT_MAX)
+				mali_internal_add_fence_array(fences, &real_num_fences, fence1);
+			else
+				mali_internal_add_fence_array(fences, &real_num_fences, fence2);
+
+			i++;
+			j++;
+		}
+	}
+
+	for (; i < num_fences1; i++)
+		mali_internal_add_fence_array(fences, &real_num_fences, fences1[i]);
+
+	for (; j < num_fences2; j++)
+		mali_internal_add_fence_array(fences, &real_num_fences, fences2[j]);
+
+	if (0 == real_num_fences)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+		fences[real_num_fences++] = fence_get(fences1[0]);
+#else
+		fences[real_num_fences++] = dma_fence_get(fences1[0]);
+#endif
+
+	if (num_fences > real_num_fences) {
+		nfences = krealloc(fences, real_num_fences * sizeof(*fences),
+				   GFP_KERNEL);
+		if (!nfences)
+			goto nfences_alloc_failed;
+
+		fences = nfences;
+	}
+
+	sync_fence = (struct mali_internal_sync_fence *)sync_file_create(fences[0]);
+	if (NULL == sync_fence) {
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to  create the mali internal sync fence when merging sync fence.\n"));
+		goto sync_fence_alloc_failed;
+	}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	fence_put(fences[0]);
+#else
+	dma_fence_put(fences[0]);
+#endif
+
+	if (mali_internal_sync_fence_set_fence_array(sync_fence, fences, real_num_fences) < 0) {
+		MALI_PRINT_ERROR(("Mali internal sync:Failed to  set fence for sync fence.\n"));
+		goto sync_fence_set_failed;
+	}
+
+	return sync_fence;
+
+sync_fence_set_failed:
+	fput(sync_fence->file);
+sync_fence_alloc_failed:
+	for (i = 0; i < real_num_fences; i++)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+		fence_put(fences[i]);
+#else
+		dma_fence_put(fences[i]);
+#endif
+nfences_alloc_failed:
+	kfree(fences);
+fences_alloc_failed:
+	return NULL;
+}
+#endif
+
+void mali_internal_sync_fence_waiter_init(struct mali_internal_sync_fence_waiter *waiter,
+		mali_internal_sync_callback_t callback)
+{
+	MALI_DEBUG_ASSERT_POINTER(waiter);
+	MALI_DEBUG_ASSERT_POINTER(callback);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 13, 0)
+	INIT_LIST_HEAD(&waiter->work.entry);
+#else
+	INIT_LIST_HEAD(&waiter->work.task_list);
+#endif
+	waiter->callback = callback;
+}
+
+int mali_internal_sync_fence_wait_async(struct mali_internal_sync_fence *sync_fence,
+					struct mali_internal_sync_fence_waiter *waiter)
+{
+	int err;
+	unsigned long flags;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_fence);
+	MALI_DEBUG_ASSERT_POINTER(waiter);
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+	err = atomic_read(&sync_fence->status);
+
+	if (0 > err)
+		return err;
+
+	if (!err)
+		return 1;
+
+	init_waitqueue_func_entry(&waiter->work, mali_internal_sync_fence_wake_up_wq);
+	waiter->work.private = sync_fence;
+
+	spin_lock_irqsave(&sync_fence->wq.lock, flags);
+	err = atomic_read(&sync_fence->status);
+
+	if (0 < err)
+		__add_wait_queue_tail(&sync_fence->wq, &waiter->work);
+	spin_unlock_irqrestore(&sync_fence->wq.lock, flags);
+
+	if (0 > err)
+		return err;
+
+	return !err;
+#else
+	if ((sync_fence->fence) && (sync_fence->fence->ops) && (sync_fence->fence->ops->signaled))
+		err = sync_fence->fence->ops->signaled(sync_fence->fence);
+	else
+		err = -1;
+
+	if (0 > err)
+		return err;
+
+	if (1 == err)
+		return err;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	err = dma_fence_add_callback(sync_fence->fence, &waiter->cb, mali_internal_fence_check_cb_func);
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(4, 9, 0)
+	err = fence_add_callback(sync_fence->fence, &waiter->cb, mali_internal_fence_check_cb_func);
+#endif
+
+	if (0 != err) {
+		if (-ENOENT == err) 
+			err = 1;
+		return err;
+	}
+	init_waitqueue_func_entry(&waiter->work, mali_internal_sync_fence_wake_up_wq);
+	waiter->work.private = sync_fence;
+
+	spin_lock_irqsave(&sync_fence->wq.lock, flags);
+	err =  sync_fence->fence->ops->signaled(sync_fence->fence);
+
+	if (0 == err){
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 13, 0)
+		__add_wait_queue_entry_tail(&sync_fence->wq, &waiter->work);
+#else
+		__add_wait_queue_tail(&sync_fence->wq, &waiter->work);
+#endif
+        }
+	spin_unlock_irqrestore(&sync_fence->wq.lock, flags);
+
+	return err;
+#endif
+}
+
+int mali_internal_sync_fence_cancel_async(struct mali_internal_sync_fence *sync_fence,
+		struct mali_internal_sync_fence_waiter *waiter)
+{
+	unsigned long flags;
+	int ret = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_fence);
+	MALI_DEBUG_ASSERT_POINTER(waiter);
+
+	spin_lock_irqsave(&sync_fence->wq.lock, flags);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 13, 0)
+	if (!list_empty(&waiter->work.entry))
+		list_del_init(&waiter->work.entry);
+#else
+	if (!list_empty(&waiter->work.task_list))
+		list_del_init(&waiter->work.task_list);
+#endif
+	else
+		ret = -ENOENT;
+	spin_unlock_irqrestore(&sync_fence->wq.lock, flags);
+
+	if (0 == ret) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+		dma_fence_remove_callback(sync_fence->fence, &waiter->cb);
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(4, 9, 0)
+		fence_remove_callback(sync_fence->fence, &waiter->cb);
+#endif
+
+	}
+
+	return ret;
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static const char *mali_internal_fence_get_driver_name(struct dma_fence *fence)
+#else
+static const char *mali_internal_fence_get_driver_name(struct fence *fence)
+#endif
+{
+	struct mali_internal_sync_point *sync_pt;
+	struct mali_internal_sync_timeline *parent;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	sync_pt = mali_internal_fence_to_sync_pt(fence);
+	parent = mali_internal_sync_pt_to_sync_timeline(sync_pt);
+
+	return parent->ops->driver_name;
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static const char *mali_internal_fence_get_timeline_name(struct dma_fence *fence)
+#else
+static const char *mali_internal_fence_get_timeline_name(struct fence *fence)
+#endif
+{
+	struct mali_internal_sync_point *sync_pt;
+	struct mali_internal_sync_timeline *parent;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	sync_pt = mali_internal_fence_to_sync_pt(fence);
+	parent = mali_internal_sync_pt_to_sync_timeline(sync_pt);
+
+	return parent->name;
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static void mali_internal_fence_release(struct dma_fence *fence)
+#else
+static void mali_internal_fence_release(struct fence *fence)
+#endif
+{
+	unsigned long flags;
+	struct mali_internal_sync_point *sync_pt;
+	struct mali_internal_sync_timeline *parent;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	sync_pt = mali_internal_fence_to_sync_pt(fence);
+	parent = mali_internal_sync_pt_to_sync_timeline(sync_pt);
+
+
+	spin_lock_irqsave(fence->lock, flags);
+	if (WARN_ON_ONCE(!list_empty(&sync_pt->sync_pt_list)))
+		list_del(&sync_pt->sync_pt_list);
+	spin_unlock_irqrestore(fence->lock, flags);
+
+	if (parent->ops->free_pt)
+		parent->ops->free_pt(sync_pt);
+
+	kref_put(&parent->kref_count, mali_internal_sync_timeline_free);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	dma_fence_free(&sync_pt->base);
+#else
+	fence_free(&sync_pt->base);
+#endif
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static bool mali_internal_fence_signaled(struct dma_fence *fence)
+#else
+static bool mali_internal_fence_signaled(struct fence *fence)
+#endif
+{
+	int ret;
+	struct mali_internal_sync_point *sync_pt;
+	struct mali_internal_sync_timeline *parent;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	sync_pt = mali_internal_fence_to_sync_pt(fence);
+	parent = mali_internal_sync_pt_to_sync_timeline(sync_pt);
+
+	ret = parent->ops->has_signaled(sync_pt);
+	if (0 > ret)
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(4, 11, 0) \
+                || (LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0) && LINUX_VERSION_CODE >= KERNEL_VERSION(4, 9, 68)))
+		fence->error = ret;
+#else
+		fence->status = ret;
+#endif
+	return ret;
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static bool mali_internal_fence_enable_signaling(struct dma_fence *fence)
+#else
+static bool mali_internal_fence_enable_signaling(struct fence *fence)
+#endif
+{
+	struct mali_internal_sync_point *sync_pt;
+	struct mali_internal_sync_timeline *parent;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+
+	sync_pt = mali_internal_fence_to_sync_pt(fence);
+	parent = mali_internal_sync_pt_to_sync_timeline(sync_pt);
+
+	if (mali_internal_fence_signaled(fence))
+		return false;
+
+	list_add_tail(&sync_pt->sync_pt_list, &parent->sync_pt_list_head);
+	return true;
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static void mali_internal_fence_value_str(struct dma_fence *fence, char *str, int size)
+#else
+static void mali_internal_fence_value_str(struct fence *fence, char *str, int size)
+#endif
+{
+	struct mali_internal_sync_point *sync_pt;
+	struct mali_internal_sync_timeline *parent;
+
+	MALI_DEBUG_ASSERT_POINTER(fence);
+	MALI_IGNORE(str);
+	MALI_IGNORE(size);
+
+	sync_pt = mali_internal_fence_to_sync_pt(fence);
+	parent = mali_internal_sync_pt_to_sync_timeline(sync_pt);
+
+	parent->ops->print_sync_pt(sync_pt);
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+static const struct dma_fence_ops fence_ops = {
+#else
+static const struct fence_ops fence_ops = {
+#endif
+	.get_driver_name = mali_internal_fence_get_driver_name,
+	.get_timeline_name = mali_internal_fence_get_timeline_name,
+	.enable_signaling = mali_internal_fence_enable_signaling,
+	.signaled = mali_internal_fence_signaled,
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	.wait = dma_fence_default_wait,
+#else
+	.wait = fence_default_wait,
+#endif
+	.release = mali_internal_fence_release,
+	.fence_value_str = mali_internal_fence_value_str,
+};
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_internal_sync.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_internal_sync.h
@@ -0,0 +1,191 @@
+/*
+ * Copyright (C) 2012-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_internal_sync.h
+ *
+ * Mali internal structure/interface for sync.
+ */
+
+#ifndef _MALI_INTERNAL_SYNC_H
+#define _MALI_INTERNAL_SYNC_H
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 6, 0)
+#include <linux/types.h>
+#include <linux/kref.h>
+#include <linux/list.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 7, 0)
+#include <sync.h>
+#else
+#include <linux/sync_file.h>
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+#include <linux/dma-fence.h>
+#else
+#include <linux/fence.h>
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 9, 0)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+#include <linux/fence-array.h>
+#else
+#include <linux/dma-fence-array.h>
+#endif
+#endif
+
+struct mali_internal_sync_timeline;
+struct mali_internal_sync_point;
+struct mali_internal_sync_fence;
+
+struct mali_internal_sync_timeline_ops {
+	const char *driver_name;
+	int (*has_signaled)(struct mali_internal_sync_point *pt);
+	void (*free_pt)(struct mali_internal_sync_point *sync_pt);
+	void (*release_obj)(struct mali_internal_sync_timeline *sync_timeline);
+	void (*print_sync_pt)(struct mali_internal_sync_point *sync_pt);
+};
+
+struct mali_internal_sync_timeline {
+	struct kref             kref_count;
+	const struct mali_internal_sync_timeline_ops  *ops;
+	char                    name[32];
+	bool                    destroyed;
+	int                     fence_context;
+	int                     value;
+	spinlock_t              sync_pt_list_lock;
+	struct list_head        sync_pt_list_head;
+};
+
+struct mali_internal_sync_point {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	struct dma_fence base;
+#else
+	struct fence base;
+#endif
+	struct list_head        sync_pt_list;
+};
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+struct mali_internal_sync_fence_cb {
+	struct fence_cb cb;
+	struct fence *fence;
+	struct mali_internal_sync_fence *sync_file;
+};
+#endif
+
+struct mali_internal_sync_fence {
+	struct file             *file;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 13, 0)
+	struct kref             kref;
+#endif
+	char            name[32];
+#ifdef CONFIG_DEBUG_FS
+	struct list_head        sync_file_list;
+#endif
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+	int num_fences;
+#endif
+	wait_queue_head_t       wq;
+#if LINUX_VERSION_CODE > KERNEL_VERSION(4, 12, 0)
+	unsigned long		flags;
+#endif
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 9, 0)
+	atomic_t                status;
+	struct mali_internal_sync_fence_cb    cbs[];
+#elif LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	struct fence *fence;
+	struct fence_cb cb;
+#else
+	struct dma_fence *fence;
+	struct dma_fence_cb cb;
+#endif
+};
+
+struct mali_internal_sync_fence_waiter;
+
+typedef void (*mali_internal_sync_callback_t)(struct mali_internal_sync_fence *sync_fence,
+		struct mali_internal_sync_fence_waiter *waiter);
+
+struct mali_internal_sync_fence_waiter {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 13, 0)
+	wait_queue_entry_t work;
+#else
+	wait_queue_t work;
+#endif
+	mali_internal_sync_callback_t callback;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 9, 0)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	struct fence_cb cb;
+#else
+	struct dma_fence_cb cb;
+#endif
+#endif
+};
+
+/**
+ * Create a mali internal sync timeline.
+ * @param ops The implementation ops for the mali internal sync timeline
+ * @param size The size to allocate
+ * @param name The sync_timeline name
+ * @return The new mali internal sync timeline if successful, NULL if not.
+ */
+struct mali_internal_sync_timeline *mali_internal_sync_timeline_create(const struct mali_internal_sync_timeline_ops *ops,
+		int size, const char *name);
+
+/**
+ * Destroy one mali internal sync timeline.
+ * @param sync_timeline The mali internal sync timeline to destroy.
+ */
+void mali_internal_sync_timeline_destroy(struct mali_internal_sync_timeline *sync_timeline);
+
+/**
+ * Signal one mali internal sync timeline.
+ * @param sync_timeline The mali internal sync timeline to signal.
+ */
+void mali_internal_sync_timeline_signal(struct mali_internal_sync_timeline *sync_timeline);
+
+/**
+ * Create one mali internal sync point.
+ * @param sync_timeline The mali internal sync timeline to add this mali internal sync point.
+  * @return the new mali internal sync point if successful, NULL if not.
+ */
+struct mali_internal_sync_point *mali_internal_sync_point_create(struct mali_internal_sync_timeline *sync_timeline, int size);
+
+/**
+ * Merge mali internal sync fences
+ * @param sync_fence1 The mali internal sync fence to merge
+ * @param sync_fence2 The mali internal sync fence to merge
+ * @return the new mali internal sync fence if successful, NULL if not.
+ */
+struct mali_internal_sync_fence *mali_internal_sync_fence_merge(struct mali_internal_sync_fence *sync_fence1,
+		struct mali_internal_sync_fence *sync_fence2);
+
+/**
+ * Get the mali internal sync fence from sync fd
+ * @param fd The sync handle to get the mali internal sync fence
+ * @return the mali internal sync fence if successful, NULL if not.
+ */
+struct mali_internal_sync_fence *mali_internal_sync_fence_fdget(int fd);
+
+
+void mali_internal_sync_fence_waiter_init(struct mali_internal_sync_fence_waiter *waiter,
+		mali_internal_sync_callback_t callback);
+
+int mali_internal_sync_fence_wait_async(struct mali_internal_sync_fence *sync_fence,
+					struct mali_internal_sync_fence_waiter *waiter);
+
+int mali_internal_sync_fence_cancel_async(struct mali_internal_sync_fence *sync_fence,
+		struct mali_internal_sync_fence_waiter *waiter);
+
+#endif /*LINUX_VERSION_CODE >= KERNEL_VERSION(4, 6, 0)*/
+#endif /* _MALI_INTERNAL_SYNC_H */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_kernel_linux.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_kernel_linux.c
@@ -0,0 +1,1215 @@
+/**
+ * Copyright (C) 2010-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_kernel_linux.c
+ * Implementation of the Linux device driver entrypoints
+ */
+#include <linux/module.h>   /* kernel module definitions */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/cdev.h>     /* character device definitions */
+#include <linux/mm.h>       /* memory manager definitions */
+#include <linux/mali/mali_utgard_ioctl.h>
+#include <linux/version.h>
+#include <linux/device.h>
+#include "mali_kernel_license.h"
+#include <linux/platform_device.h>
+#include <linux/miscdevice.h>
+#include <linux/bug.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+
+#include <linux/mali/mali_utgard.h>
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_kernel_core.h"
+#include "mali_osk.h"
+#include "mali_kernel_linux.h"
+#include "mali_ukk.h"
+#include "mali_ukk_wrappers.h"
+#include "mali_kernel_sysfs.h"
+#include "mali_pm.h"
+#include "mali_kernel_license.h"
+#include "mali_memory.h"
+#include "mali_memory_dma_buf.h"
+#include "mali_memory_manager.h"
+#include "mali_memory_swap_alloc.h"
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+#include "mali_profiling_internal.h"
+#endif
+
+#if defined(CONFIG_ARCH_ZYNQMP)
+/* Initialize variables for clocks */
+struct clk *clk_gpu;
+struct clk *clk_gpu_pp0;
+struct clk *clk_gpu_pp1;
+mali_bool clk_enabled;
+#endif
+
+#if defined(CONFIG_MALI400_PROFILING) && defined(CONFIG_MALI_DVFS)
+#include "mali_osk_profiling.h"
+#include "mali_dvfs_policy.h"
+
+static int is_first_resume = 1;
+/*Store the clk and vol for boot/insmod and mali_resume*/
+static struct mali_gpu_clk_item mali_gpu_clk[2];
+#endif
+
+/* Streamline support for the Mali driver */
+#if defined(CONFIG_TRACEPOINTS) && defined(CONFIG_MALI400_PROFILING)
+/* Ask Linux to create the tracepoints */
+#define CREATE_TRACE_POINTS
+#include "mali_linux_trace.h"
+
+EXPORT_TRACEPOINT_SYMBOL_GPL(mali_timeline_event);
+EXPORT_TRACEPOINT_SYMBOL_GPL(mali_hw_counter);
+EXPORT_TRACEPOINT_SYMBOL_GPL(mali_sw_counters);
+#endif /* CONFIG_TRACEPOINTS */
+
+#ifdef CONFIG_MALI_DEVFREQ
+#include "mali_devfreq.h"
+#include "mali_osk_mali.h"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 4, 0)
+#include <linux/pm_opp.h>
+#else
+/* In 3.13 the OPP include header file, types, and functions were all
+ * renamed. Use the old filename for the include, and define the new names to
+ * the old, when an old kernel is detected.
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 13, 0)
+#include <linux/pm_opp.h>
+#else
+#include <linux/opp.h>
+#endif /* Linux >= 3.13*/
+#define dev_pm_opp_of_add_table of_init_opp_table
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 19, 0)
+#define dev_pm_opp_of_remove_table of_free_opp_table
+#endif /* Linux >= 3.19 */
+#endif /* Linux >= 4.4.0 */
+#endif
+
+/* from the __malidrv_build_info.c file that is generated during build */
+extern const char *__malidrv_build_info(void);
+
+/* Module parameter to control log level */
+int mali_debug_level = 2;
+module_param(mali_debug_level, int, S_IRUSR | S_IWUSR | S_IWGRP | S_IRGRP | S_IROTH); /* rw-rw-r-- */
+MODULE_PARM_DESC(mali_debug_level, "Higher number, more dmesg output");
+
+extern int mali_max_job_runtime;
+module_param(mali_max_job_runtime, int, S_IRUSR | S_IWUSR | S_IWGRP | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_max_job_runtime, "Maximum allowed job runtime in msecs.\nJobs will be killed after this no matter what");
+
+extern int mali_l2_max_reads;
+module_param(mali_l2_max_reads, int, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_l2_max_reads, "Maximum reads for Mali L2 cache");
+
+extern unsigned int mali_dedicated_mem_start;
+module_param(mali_dedicated_mem_start, uint, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_dedicated_mem_start, "Physical start address of dedicated Mali GPU memory.");
+
+extern unsigned int mali_dedicated_mem_size;
+module_param(mali_dedicated_mem_size, uint, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_dedicated_mem_size, "Size of dedicated Mali GPU memory.");
+
+extern unsigned int mali_shared_mem_size;
+module_param(mali_shared_mem_size, uint, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_shared_mem_size, "Size of shared Mali GPU memory.");
+
+#if defined(CONFIG_MALI400_PROFILING)
+extern int mali_boot_profiling;
+module_param(mali_boot_profiling, int, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_boot_profiling, "Start profiling as a part of Mali driver initialization");
+#endif
+
+extern int mali_max_pp_cores_group_1;
+module_param(mali_max_pp_cores_group_1, int, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_max_pp_cores_group_1, "Limit the number of PP cores to use from first PP group.");
+
+extern int mali_max_pp_cores_group_2;
+module_param(mali_max_pp_cores_group_2, int, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_max_pp_cores_group_2, "Limit the number of PP cores to use from second PP group (Mali-450 only).");
+
+extern unsigned int mali_mem_swap_out_threshold_value;
+module_param(mali_mem_swap_out_threshold_value, uint, S_IRUSR | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_mem_swap_out_threshold_value, "Threshold value used to limit how much swappable memory cached in Mali driver.");
+
+#if defined(CONFIG_MALI_DVFS)
+/** the max fps the same as display vsync default 60, can set by module insert parameter */
+extern int mali_max_system_fps;
+module_param(mali_max_system_fps, int, S_IRUSR | S_IWUSR | S_IWGRP | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_max_system_fps, "Max system fps the same as display VSYNC.");
+
+/** a lower limit on their desired FPS default 58, can set by module insert parameter*/
+extern int mali_desired_fps;
+module_param(mali_desired_fps, int, S_IRUSR | S_IWUSR | S_IWGRP | S_IRGRP | S_IROTH);
+MODULE_PARM_DESC(mali_desired_fps, "A bit lower than max_system_fps which user desired fps");
+#endif
+
+#if MALI_ENABLE_CPU_CYCLES
+#include <linux/cpumask.h>
+#include <linux/timer.h>
+#include <asm/smp.h>
+static struct timer_list mali_init_cpu_clock_timers[8];
+static u32 mali_cpu_clock_last_value[8] = {0,};
+#endif
+
+/* Export symbols from common code: mali_user_settings.c */
+#include "mali_user_settings_db.h"
+EXPORT_SYMBOL(mali_set_user_setting);
+EXPORT_SYMBOL(mali_get_user_setting);
+
+static char mali_dev_name[] = "mali"; /* should be const, but the functions we call requires non-cost */
+
+/* This driver only supports one Mali device, and this variable stores this single platform device */
+struct platform_device *mali_platform_device = NULL;
+
+/* This driver only supports one Mali device, and this variable stores the exposed misc device (/dev/mali) */
+static struct miscdevice mali_miscdevice = { 0, };
+
+static int mali_miscdevice_register(struct platform_device *pdev);
+static void mali_miscdevice_unregister(void);
+
+static int mali_open(struct inode *inode, struct file *filp);
+static int mali_release(struct inode *inode, struct file *filp);
+#ifdef HAVE_UNLOCKED_IOCTL
+static long mali_ioctl(struct file *filp, unsigned int cmd, unsigned long arg);
+#else
+static int mali_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long arg);
+#endif
+
+static int mali_probe(struct platform_device *pdev);
+static int mali_remove(struct platform_device *pdev);
+
+static int mali_driver_suspend_scheduler(struct device *dev);
+static int mali_driver_resume_scheduler(struct device *dev);
+
+#ifdef CONFIG_PM_RUNTIME
+static int mali_driver_runtime_suspend(struct device *dev);
+static int mali_driver_runtime_resume(struct device *dev);
+static int mali_driver_runtime_idle(struct device *dev);
+#endif
+
+#if defined(MALI_FAKE_PLATFORM_DEVICE)
+#if defined(CONFIG_MALI_DT)
+extern int mali_platform_device_init(struct platform_device *device);
+extern int mali_platform_device_deinit(struct platform_device *device);
+#else
+extern int mali_platform_device_register(void);
+extern int mali_platform_device_unregister(void);
+#endif
+#endif
+
+/* Linux power management operations provided by the Mali device driver */
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 29))
+struct pm_ext_ops mali_dev_ext_pm_ops = {
+	.base =
+	{
+		.suspend = mali_driver_suspend_scheduler,
+		.resume = mali_driver_resume_scheduler,
+		.freeze = mali_driver_suspend_scheduler,
+		.thaw =   mali_driver_resume_scheduler,
+	},
+};
+#else
+static const struct dev_pm_ops mali_dev_pm_ops = {
+#ifdef CONFIG_PM_RUNTIME
+	.runtime_suspend = mali_driver_runtime_suspend,
+	.runtime_resume = mali_driver_runtime_resume,
+	.runtime_idle = mali_driver_runtime_idle,
+#endif
+	.suspend = mali_driver_suspend_scheduler,
+	.resume = mali_driver_resume_scheduler,
+	.freeze = mali_driver_suspend_scheduler,
+	.thaw = mali_driver_resume_scheduler,
+	.poweroff = mali_driver_suspend_scheduler,
+};
+#endif
+
+#ifdef CONFIG_MALI_DT
+static struct of_device_id base_dt_ids[] = {
+	{.compatible = "arm,mali-300"},
+	{.compatible = "arm,mali-400"},
+	{.compatible = "arm,mali-450"},
+	{.compatible = "arm,mali-470"},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, base_dt_ids);
+#endif
+
+/* The Mali device driver struct */
+static struct platform_driver mali_platform_driver = {
+	.probe  = mali_probe,
+	.remove = mali_remove,
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 29))
+	.pm = &mali_dev_ext_pm_ops,
+#endif
+	.driver =
+	{
+		.name   = MALI_GPU_NAME_UTGARD,
+		.owner  = THIS_MODULE,
+		.bus = &platform_bus_type,
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 29))
+		.pm = &mali_dev_pm_ops,
+#endif
+#ifdef CONFIG_MALI_DT
+		.of_match_table = of_match_ptr(base_dt_ids),
+#endif
+	},
+};
+
+/* Linux misc device operations (/dev/mali) */
+struct file_operations mali_fops = {
+	.owner = THIS_MODULE,
+	.open = mali_open,
+	.release = mali_release,
+#ifdef HAVE_UNLOCKED_IOCTL
+	.unlocked_ioctl = mali_ioctl,
+#else
+	.ioctl = mali_ioctl,
+#endif
+	.compat_ioctl = mali_ioctl,
+	.mmap = mali_mmap
+};
+
+static int mali_enable_clk(void)
+{
+#if defined(CONFIG_ARCH_ZYNQMP)
+	int err = 0;
+
+	if (clk_enabled)
+		return 0;
+
+	clk_enabled = MALI_TRUE;
+	err = clk_prepare_enable(clk_gpu);
+	if (err) {
+		MALI_PRINT_ERROR(("Could not enable clock for GP\n\r"));
+		return err;
+	}
+	err = clk_prepare_enable(clk_gpu_pp0);
+	if (err) {
+		MALI_PRINT_ERROR(("Could not enable clock for PP0\n\r"));
+		return err;
+	}
+	err = clk_prepare_enable(clk_gpu_pp1);
+	if (err) {
+		MALI_PRINT_ERROR(("Could not enable clock for PP1\n\r"));
+		return err;
+	}
+#endif
+	return 0;
+}
+
+static void mali_disable_clk(void)
+{
+#if defined(CONFIG_ARCH_ZYNQMP)
+	if (clk_enabled) {
+		clk_enabled = MALI_FALSE;
+		clk_disable_unprepare(clk_gpu);
+		clk_disable_unprepare(clk_gpu_pp0);
+		clk_disable_unprepare(clk_gpu_pp1);
+	}
+#endif
+}
+
+#if MALI_ENABLE_CPU_CYCLES
+void mali_init_cpu_time_counters(int reset, int enable_divide_by_64)
+{
+	/* The CPU assembly reference used is: ARM Architecture Reference Manual ARMv7-AR C.b */
+	u32 write_value;
+
+	/* See B4.1.116 PMCNTENSET, Performance Monitors Count Enable Set register, VMSA */
+	/* setting p15 c9 c12 1 to 0x8000000f==CPU_CYCLE_ENABLE |EVENT_3_ENABLE|EVENT_2_ENABLE|EVENT_1_ENABLE|EVENT_0_ENABLE */
+	asm volatile("mcr p15, 0, %0, c9, c12, 1" :: "r"(0x8000000f));
+
+
+	/* See B4.1.117 PMCR, Performance Monitors Control Register. Writing to p15, c9, c12, 0 */
+	write_value = 1 << 0; /* Bit 0 set. Enable counters */
+	if (reset) {
+		write_value |= 1 << 1; /* Reset event counters */
+		write_value |= 1 << 2; /* Reset cycle counter  */
+	}
+	if (enable_divide_by_64) {
+		write_value |= 1 << 3; /* Enable the Clock divider by 64 */
+	}
+	write_value |= 1 << 4; /* Export enable. Not needed */
+	asm volatile("MCR p15, 0, %0, c9, c12, 0\t\n" :: "r"(write_value));
+
+	/* PMOVSR Overflow Flag Status Register - Clear Clock and Event overflows */
+	asm volatile("MCR p15, 0, %0, c9, c12, 3\t\n" :: "r"(0x8000000f));
+
+
+	/* See B4.1.124 PMUSERENR - setting p15 c9 c14 to 1" */
+	/* User mode access to the Performance Monitors enabled. */
+	/* Lets User space read cpu clock cycles */
+	asm volatile("mcr p15, 0, %0, c9, c14, 0" :: "r"(1));
+}
+
+/** A timer function that configures the cycle clock counter on current CPU.
+ * The function \a mali_init_cpu_time_counters_on_all_cpus sets up this
+ * function to trigger on all Cpus during module load.
+ */
+static void mali_init_cpu_clock_timer_func(unsigned long data)
+{
+	int reset_counters, enable_divide_clock_counter_by_64;
+	int current_cpu = raw_smp_processor_id();
+	unsigned int sample0;
+	unsigned int sample1;
+
+	MALI_IGNORE(data);
+
+	reset_counters = 1;
+	enable_divide_clock_counter_by_64 = 0;
+	mali_init_cpu_time_counters(reset_counters, enable_divide_clock_counter_by_64);
+
+	sample0 = mali_get_cpu_cyclecount();
+	sample1 = mali_get_cpu_cyclecount();
+
+	MALI_DEBUG_PRINT(3, ("Init Cpu %d cycle counter- First two samples: %08x %08x \n", current_cpu, sample0, sample1));
+}
+
+/** A timer functions for storing current time on all cpus.
+ * Used for checking if the clocks have similar values or if they are drifting.
+ */
+static void mali_print_cpu_clock_timer_func(unsigned long data)
+{
+	int current_cpu = raw_smp_processor_id();
+	unsigned int sample0;
+
+	MALI_IGNORE(data);
+	sample0 = mali_get_cpu_cyclecount();
+	if (current_cpu < 8) {
+		mali_cpu_clock_last_value[current_cpu] = sample0;
+	}
+}
+
+/** Init the performance registers on all CPUs to count clock cycles.
+ * For init \a print_only should be 0.
+ * If \a print_only is 1, it will intead print the current clock value of all CPUs.
+ */
+void mali_init_cpu_time_counters_on_all_cpus(int print_only)
+{
+	int i = 0;
+	int cpu_number;
+	int jiffies_trigger;
+	int jiffies_wait;
+
+	jiffies_wait = 2;
+	jiffies_trigger = jiffies + jiffies_wait;
+
+	for (i = 0 ; i < 8 ; i++) {
+		init_timer(&mali_init_cpu_clock_timers[i]);
+		if (print_only) mali_init_cpu_clock_timers[i].function = mali_print_cpu_clock_timer_func;
+		else            mali_init_cpu_clock_timers[i].function = mali_init_cpu_clock_timer_func;
+		mali_init_cpu_clock_timers[i].expires = jiffies_trigger ;
+	}
+	cpu_number = cpumask_first(cpu_online_mask);
+	for (i = 0 ; i < 8 ; i++) {
+		int next_cpu;
+		add_timer_on(&mali_init_cpu_clock_timers[i], cpu_number);
+		next_cpu = cpumask_next(cpu_number, cpu_online_mask);
+		if (next_cpu >= nr_cpu_ids) break;
+		cpu_number = next_cpu;
+	}
+
+	while (jiffies_wait) jiffies_wait = schedule_timeout_uninterruptible(jiffies_wait);
+
+	for (i = 0 ; i < 8 ; i++) {
+		del_timer_sync(&mali_init_cpu_clock_timers[i]);
+	}
+
+	if (print_only) {
+		if ((0 == mali_cpu_clock_last_value[2]) && (0 == mali_cpu_clock_last_value[3])) {
+			/* Diff can be printed if we want to check if the clocks are in sync
+			int diff = mali_cpu_clock_last_value[0] - mali_cpu_clock_last_value[1];*/
+			MALI_DEBUG_PRINT(2, ("CPU cycle counters readout all: %08x %08x\n", mali_cpu_clock_last_value[0], mali_cpu_clock_last_value[1]));
+		} else {
+			MALI_DEBUG_PRINT(2, ("CPU cycle counters readout all: %08x %08x %08x %08x\n", mali_cpu_clock_last_value[0], mali_cpu_clock_last_value[1], mali_cpu_clock_last_value[2], mali_cpu_clock_last_value[3]));
+		}
+	}
+}
+#endif
+
+int mali_module_init(void)
+{
+	int err = 0;
+
+	MALI_DEBUG_PRINT(2, ("Inserting Mali v%d device driver. \n", _MALI_API_VERSION));
+	MALI_DEBUG_PRINT(2, ("Compiled: %s, time: %s.\n", __DATE__, __TIME__));
+	MALI_DEBUG_PRINT(2, ("Driver revision: %s\n", SVN_REV_STRING));
+
+#if MALI_ENABLE_CPU_CYCLES
+	mali_init_cpu_time_counters_on_all_cpus(0);
+	MALI_DEBUG_PRINT(2, ("CPU cycle counter setup complete\n"));
+	/* Printing the current cpu counters */
+	mali_init_cpu_time_counters_on_all_cpus(1);
+#endif
+
+	/* Initialize module wide settings */
+#ifdef MALI_FAKE_PLATFORM_DEVICE
+#ifndef CONFIG_MALI_DT
+	MALI_DEBUG_PRINT(2, ("mali_module_init() registering device\n"));
+	err = mali_platform_device_register();
+	if (0 != err) {
+		return err;
+	}
+#endif
+#endif
+
+	MALI_DEBUG_PRINT(2, ("mali_module_init() registering driver\n"));
+
+	err = platform_driver_register(&mali_platform_driver);
+
+	if (0 != err) {
+		MALI_DEBUG_PRINT(2, ("mali_module_init() Failed to register driver (%d)\n", err));
+#ifdef MALI_FAKE_PLATFORM_DEVICE
+#ifndef CONFIG_MALI_DT
+		mali_platform_device_unregister();
+#endif
+#endif
+		mali_platform_device = NULL;
+		return err;
+	}
+
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+	err = _mali_internal_profiling_init(mali_boot_profiling ? MALI_TRUE : MALI_FALSE);
+	if (0 != err) {
+		/* No biggie if we wheren't able to initialize the profiling */
+		MALI_PRINT_ERROR(("Failed to initialize profiling, feature will be unavailable\n"));
+	}
+#endif
+
+	/* Tracing the current frequency and voltage from boot/insmod*/
+#if defined(CONFIG_MALI400_PROFILING) && defined(CONFIG_MALI_DVFS)
+	/* Just call mali_get_current_gpu_clk_item(),to record current clk info.*/
+	mali_get_current_gpu_clk_item(&mali_gpu_clk[0]);
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+				      MALI_PROFILING_EVENT_CHANNEL_GPU |
+				      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+				      mali_gpu_clk[0].clock,
+				      mali_gpu_clk[0].vol / 1000,
+				      0, 0, 0);
+#endif
+
+	MALI_PRINT(("Mali device driver loaded\n"));
+
+	return 0; /* Success */
+}
+
+void mali_module_exit(void)
+{
+	MALI_DEBUG_PRINT(2, ("Unloading Mali v%d device driver.\n", _MALI_API_VERSION));
+
+	MALI_DEBUG_PRINT(2, ("mali_module_exit() unregistering driver\n"));
+
+	platform_driver_unregister(&mali_platform_driver);
+
+#if defined(MALI_FAKE_PLATFORM_DEVICE)
+#ifndef CONFIG_MALI_DT
+	MALI_DEBUG_PRINT(2, ("mali_module_exit() unregistering device\n"));
+	mali_platform_device_unregister();
+#endif
+#endif
+
+	/* Tracing the current frequency and voltage from rmmod*/
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+				      MALI_PROFILING_EVENT_CHANNEL_GPU |
+				      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+				      0,
+				      0,
+				      0, 0, 0);
+
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+	_mali_internal_profiling_term();
+#endif
+
+	MALI_PRINT(("Mali device driver unloaded\n"));
+}
+
+#ifdef CONFIG_MALI_DEVFREQ
+struct mali_device *mali_device_alloc(void)
+{
+	return kzalloc(sizeof(struct mali_device), GFP_KERNEL);
+}
+
+void mali_device_free(struct mali_device *mdev)
+{
+	kfree(mdev);
+}
+#endif
+
+static int mali_probe(struct platform_device *pdev)
+{
+	int err;
+#ifdef CONFIG_MALI_DEVFREQ
+	struct mali_device *mdev;
+#endif
+
+	MALI_DEBUG_PRINT(2, ("mali_probe(): Called for platform device %s\n", pdev->name));
+
+	if (NULL != mali_platform_device) {
+		/* Already connected to a device, return error */
+		MALI_PRINT_ERROR(("mali_probe(): The Mali driver is already connected with a Mali device."));
+		return -EEXIST;
+	}
+
+	mali_platform_device = pdev;
+
+#ifdef CONFIG_MALI_DT
+	/* If we use DT to initialize our DDK, we have to prepare somethings. */
+	err = mali_platform_device_init(mali_platform_device);
+	if (0 != err) {
+		MALI_PRINT_ERROR(("mali_probe(): Failed to initialize platform device."));
+		mali_platform_device = NULL;
+		return -EFAULT;
+	}
+#endif
+
+#ifdef CONFIG_MALI_DEVFREQ
+	mdev = mali_device_alloc();
+	if (!mdev) {
+		MALI_PRINT_ERROR(("Can't allocate mali device private data\n"));
+		return -ENOMEM;
+	}
+
+	mdev->dev = &pdev->dev;
+	dev_set_drvdata(mdev->dev, mdev);
+
+	/*Initilization clock and regulator*/
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 12, 0)) && defined(CONFIG_OF) \
+                        && defined(CONFIG_REGULATOR)
+	mdev->regulator = regulator_get_optional(mdev->dev, "mali");
+	if (IS_ERR_OR_NULL(mdev->regulator)) {
+		MALI_DEBUG_PRINT(2, ("Continuing without Mali regulator control\n"));
+		mdev->regulator = NULL;
+		/* Allow probe to continue without regulator */
+	}
+#endif /* LINUX_VERSION_CODE >= 3, 12, 0 */
+
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 7, 0)) && defined(CONFIG_OF) \
+                        && defined(CONFIG_PM_OPP)
+	/* Register the OPPs if they are available in device tree */
+	if (dev_pm_opp_of_add_table(mdev->dev) < 0)
+		MALI_DEBUG_PRINT(3, ("OPP table not found\n"));
+#endif
+
+	/* Need to name the gpu clock "clk_mali" in the device tree */
+	mdev->clock = clk_get(mdev->dev, "clk_mali");
+	if (IS_ERR_OR_NULL(mdev->clock)) {
+		MALI_DEBUG_PRINT(2, ("Continuing without Mali clock control\n"));
+		mdev->clock = NULL;
+		/* Allow probe to continue without clock. */
+	} else {
+		err = clk_prepare_enable(mdev->clock);
+		if (err) {
+			MALI_PRINT_ERROR(("Failed to prepare and enable clock (%d)\n", err));
+			goto clock_prepare_failed;
+		}
+	}
+
+	/* initilize pm metrics related */
+	if (mali_pm_metrics_init(mdev) < 0) {
+		MALI_DEBUG_PRINT(2, ("mali pm metrics init failed\n"));
+		goto pm_metrics_init_failed;
+	}
+
+	if (mali_devfreq_init(mdev) < 0) {
+		MALI_DEBUG_PRINT(2, ("mali devfreq init failed\n"));
+		goto devfreq_init_failed;
+	}
+#endif
+
+#if defined(CONFIG_ARCH_ZYNQMP)
+	/* Initialize clocks for GPU and PP */
+	clk_gpu = devm_clk_get(&pdev->dev, "gpu");
+	if (IS_ERR(clk_gpu))
+		return PTR_ERR(clk_gpu);
+
+	clk_gpu_pp0 = devm_clk_get(&pdev->dev, "gpu_pp0");
+	if (IS_ERR(clk_gpu_pp0))
+		return PTR_ERR(clk_gpu_pp0);
+
+	clk_gpu_pp1 = devm_clk_get(&pdev->dev, "gpu_pp1");
+	if (IS_ERR(clk_gpu_pp1))
+		return PTR_ERR(clk_gpu_pp1);
+#endif
+
+	err = mali_enable_clk();
+	if (err)
+		return err;
+	if (_MALI_OSK_ERR_OK == _mali_osk_wq_init()) {
+		/* Initialize the Mali GPU HW specified by pdev */
+		if (_MALI_OSK_ERR_OK == mali_initialize_subsystems()) {
+			/* Register a misc device (so we are accessible from user space) */
+			err = mali_miscdevice_register(pdev);
+			if (0 == err) {
+				/* Setup sysfs entries */
+				err = mali_sysfs_register(mali_dev_name);
+
+				if (0 == err) {
+					MALI_DEBUG_PRINT(2, ("mali_probe(): Successfully initialized driver for platform device %s\n", pdev->name));
+
+					return 0;
+				} else {
+					MALI_PRINT_ERROR(("mali_probe(): failed to register sysfs entries"));
+				}
+				mali_miscdevice_unregister();
+			} else {
+				MALI_PRINT_ERROR(("mali_probe(): failed to register Mali misc device."));
+			}
+			mali_terminate_subsystems();
+		} else {
+			MALI_PRINT_ERROR(("mali_probe(): Failed to initialize Mali device driver."));
+		}
+		_mali_osk_wq_term();
+	}
+
+
+#ifdef CONFIG_MALI_DEVFREQ
+	mali_devfreq_term(mdev);
+devfreq_init_failed:
+	mali_pm_metrics_term(mdev);
+pm_metrics_init_failed:
+	clk_disable_unprepare(mdev->clock);
+	mali_disable_clk();
+clock_prepare_failed:
+	clk_put(mdev->clock);
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 19, 0)) && defined(CONFIG_OF) \
+                        && defined(CONFIG_PM_OPP)
+	dev_pm_opp_of_remove_table(mdev->dev);
+#endif
+
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 12, 0)) && defined(CONFIG_OF) \
+                        && defined(CONFIG_REGULATOR)
+	regulator_put(mdev->regulator);
+#endif /* LINUX_VERSION_CODE >= 3, 12, 0 */
+	mali_device_free(mdev);
+#endif
+
+#ifdef CONFIG_MALI_DT
+	mali_platform_device_deinit(mali_platform_device);
+#endif
+	mali_platform_device = NULL;
+	return -EFAULT;
+}
+
+static int mali_remove(struct platform_device *pdev)
+{
+#ifdef CONFIG_MALI_DEVFREQ
+	struct mali_device *mdev = dev_get_drvdata(&pdev->dev);
+#endif
+
+	MALI_DEBUG_PRINT(2, ("mali_remove() called for platform device %s\n", pdev->name));
+	mali_sysfs_unregister();
+	mali_miscdevice_unregister();
+	mali_terminate_subsystems();
+	_mali_osk_wq_term();
+
+#ifdef CONFIG_MALI_DEVFREQ
+	mali_devfreq_term(mdev);
+
+	mali_pm_metrics_term(mdev);
+
+	if (mdev->clock) {
+		clk_disable_unprepare(mdev->clock);
+		clk_put(mdev->clock);
+		mdev->clock = NULL;
+	}
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 19, 0)) && defined(CONFIG_OF) \
+                        && defined(CONFIG_PM_OPP)
+	dev_pm_opp_of_remove_table(mdev->dev);
+#endif
+
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 12, 0)) && defined(CONFIG_OF) \
+                        && defined(CONFIG_REGULATOR)
+	regulator_put(mdev->regulator);
+#endif /* LINUX_VERSION_CODE >= 3, 12, 0 */
+	mali_device_free(mdev);
+#endif
+
+#ifdef CONFIG_MALI_DT
+	mali_platform_device_deinit(mali_platform_device);
+#endif
+	mali_platform_device = NULL;
+
+#if defined(CONFIG_ARCH_ZYNQMP)
+	/* Remove clock */
+	mali_disable_clk();
+#endif
+
+	return 0;
+}
+
+static int mali_miscdevice_register(struct platform_device *pdev)
+{
+	int err;
+
+	mali_miscdevice.minor = MISC_DYNAMIC_MINOR;
+	mali_miscdevice.name = mali_dev_name;
+	mali_miscdevice.fops = &mali_fops;
+	mali_miscdevice.parent = get_device(&pdev->dev);
+
+	err = misc_register(&mali_miscdevice);
+	if (0 != err) {
+		MALI_PRINT_ERROR(("Failed to register misc device, misc_register() returned %d\n", err));
+	}
+
+	return err;
+}
+
+static void mali_miscdevice_unregister(void)
+{
+	misc_deregister(&mali_miscdevice);
+}
+
+static int mali_driver_suspend_scheduler(struct device *dev)
+{
+#ifdef CONFIG_MALI_DEVFREQ
+	struct mali_device *mdev = dev_get_drvdata(dev);
+	if (!mdev)
+		return -ENODEV;
+#endif
+
+#if defined(CONFIG_MALI_DEVFREQ) && \
+                (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0))
+	devfreq_suspend_device(mdev->devfreq);
+#endif
+
+	mali_pm_os_suspend(MALI_TRUE);
+	/* Tracing the frequency and voltage after mali is suspended */
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+				      MALI_PROFILING_EVENT_CHANNEL_GPU |
+				      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+				      0,
+				      0,
+				      0, 0, 0);
+	return 0;
+}
+
+static int mali_driver_resume_scheduler(struct device *dev)
+{
+#ifdef CONFIG_MALI_DEVFREQ
+	struct mali_device *mdev = dev_get_drvdata(dev);
+	if (!mdev)
+		return -ENODEV;
+#endif
+
+	/* Tracing the frequency and voltage after mali is resumed */
+#if defined(CONFIG_MALI400_PROFILING) && defined(CONFIG_MALI_DVFS)
+	/* Just call mali_get_current_gpu_clk_item() once,to record current clk info.*/
+	if (is_first_resume == 1) {
+		mali_get_current_gpu_clk_item(&mali_gpu_clk[1]);
+		is_first_resume = 0;
+	}
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+				      MALI_PROFILING_EVENT_CHANNEL_GPU |
+				      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+				      mali_gpu_clk[1].clock,
+				      mali_gpu_clk[1].vol / 1000,
+				      0, 0, 0);
+#endif
+	mali_pm_os_resume();
+
+#if defined(CONFIG_MALI_DEVFREQ) && \
+                (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0))
+	devfreq_resume_device(mdev->devfreq);
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_RUNTIME
+static int mali_driver_runtime_suspend(struct device *dev)
+{
+#ifdef CONFIG_MALI_DEVFREQ
+	struct mali_device *mdev = dev_get_drvdata(dev);
+	if (!mdev)
+		return -ENODEV;
+#endif
+
+	if (MALI_TRUE == mali_pm_runtime_suspend()) {
+		/* Tracing the frequency and voltage after mali is suspended */
+		_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+					      MALI_PROFILING_EVENT_CHANNEL_GPU |
+					      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+					      0,
+					      0,
+					      0, 0, 0);
+
+#if defined(CONFIG_MALI_DEVFREQ) && \
+                (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0))
+		MALI_DEBUG_PRINT(4, ("devfreq_suspend_device: stop devfreq monitor\n"));
+		devfreq_suspend_device(mdev->devfreq);
+#endif
+
+	mali_disable_clk();
+
+		return 0;
+	} else {
+		return -EBUSY;
+	}
+}
+
+static int mali_driver_runtime_resume(struct device *dev)
+{
+	int err ;
+
+	err = mali_enable_clk();
+	if (err)
+		return err;
+#ifdef CONFIG_MALI_DEVFREQ
+	struct mali_device *mdev = dev_get_drvdata(dev);
+	if (!mdev)
+		return -ENODEV;
+#endif
+
+	/* Tracing the frequency and voltage after mali is resumed */
+#if defined(CONFIG_MALI400_PROFILING) && defined(CONFIG_MALI_DVFS)
+	/* Just call mali_get_current_gpu_clk_item() once,to record current clk info.*/
+	if (is_first_resume == 1) {
+		mali_get_current_gpu_clk_item(&mali_gpu_clk[1]);
+		is_first_resume = 0;
+	}
+	_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
+				      MALI_PROFILING_EVENT_CHANNEL_GPU |
+				      MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
+				      mali_gpu_clk[1].clock,
+				      mali_gpu_clk[1].vol / 1000,
+				      0, 0, 0);
+#endif
+
+	mali_pm_runtime_resume();
+
+#if defined(CONFIG_MALI_DEVFREQ) && \
+                (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0))
+	MALI_DEBUG_PRINT(4, ("devfreq_resume_device: start devfreq monitor\n"));
+	devfreq_resume_device(mdev->devfreq);
+#endif
+	return 0;
+}
+
+static int mali_driver_runtime_idle(struct device *dev)
+{
+	/* Nothing to do */
+	return 0;
+}
+#endif
+
+static int mali_open(struct inode *inode, struct file *filp)
+{
+	struct mali_session_data *session_data;
+	_mali_osk_errcode_t err;
+
+	/* input validation */
+	if (mali_miscdevice.minor != iminor(inode)) {
+		MALI_PRINT_ERROR(("mali_open() Minor does not match\n"));
+		return -ENODEV;
+	}
+
+	/* allocated struct to track this session */
+	err = _mali_ukk_open((void **)&session_data);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	/* initialize file pointer */
+	filp->f_pos = 0;
+
+	/* link in our session data */
+	filp->private_data = (void *)session_data;
+
+	filp->f_mapping = mali_mem_swap_get_global_swap_file()->f_mapping;
+
+	return 0;
+}
+
+static int mali_release(struct inode *inode, struct file *filp)
+{
+	_mali_osk_errcode_t err;
+
+	/* input validation */
+	if (mali_miscdevice.minor != iminor(inode)) {
+		MALI_PRINT_ERROR(("mali_release() Minor does not match\n"));
+		return -ENODEV;
+	}
+
+	err = _mali_ukk_close((void **)&filp->private_data);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	return 0;
+}
+
+int map_errcode(_mali_osk_errcode_t err)
+{
+	switch (err) {
+	case _MALI_OSK_ERR_OK :
+		return 0;
+	case _MALI_OSK_ERR_FAULT:
+		return -EFAULT;
+	case _MALI_OSK_ERR_INVALID_FUNC:
+		return -ENOTTY;
+	case _MALI_OSK_ERR_INVALID_ARGS:
+		return -EINVAL;
+	case _MALI_OSK_ERR_NOMEM:
+		return -ENOMEM;
+	case _MALI_OSK_ERR_TIMEOUT:
+		return -ETIMEDOUT;
+	case _MALI_OSK_ERR_RESTARTSYSCALL:
+		return -ERESTARTSYS;
+	case _MALI_OSK_ERR_ITEM_NOT_FOUND:
+		return -ENOENT;
+	default:
+		return -EFAULT;
+	}
+}
+
+#ifdef HAVE_UNLOCKED_IOCTL
+static long mali_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
+#else
+static int mali_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long arg)
+#endif
+{
+	int err;
+	struct mali_session_data *session_data;
+
+#ifndef HAVE_UNLOCKED_IOCTL
+	/* inode not used */
+	(void)inode;
+#endif
+
+	MALI_DEBUG_PRINT(7, ("Ioctl received 0x%08X 0x%08lX\n", cmd, arg));
+
+	session_data = (struct mali_session_data *)filp->private_data;
+	if (NULL == session_data) {
+		MALI_DEBUG_PRINT(7, ("filp->private_data was NULL\n"));
+		return -ENOTTY;
+	}
+
+	if (NULL == (void *)arg) {
+		MALI_DEBUG_PRINT(7, ("arg was NULL\n"));
+		return -ENOTTY;
+	}
+
+	switch (cmd) {
+	case MALI_IOC_WAIT_FOR_NOTIFICATION:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_wait_for_notification_s), sizeof(u64)));
+		err = wait_for_notification_wrapper(session_data, (_mali_uk_wait_for_notification_s __user *)arg);
+		break;
+
+	case MALI_IOC_GET_API_VERSION_V2:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_get_api_version_v2_s), sizeof(u64)));
+		err = get_api_version_v2_wrapper(session_data, (_mali_uk_get_api_version_v2_s __user *)arg);
+		break;
+
+	case MALI_IOC_GET_API_VERSION:
+		err = get_api_version_wrapper(session_data, (_mali_uk_get_api_version_s __user *)arg);
+		break;
+
+	case MALI_IOC_POST_NOTIFICATION:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_post_notification_s), sizeof(u64)));
+		err = post_notification_wrapper(session_data, (_mali_uk_post_notification_s __user *)arg);
+		break;
+
+	case MALI_IOC_GET_USER_SETTINGS:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_get_user_settings_s), sizeof(u64)));
+		err = get_user_settings_wrapper(session_data, (_mali_uk_get_user_settings_s __user *)arg);
+		break;
+
+	case MALI_IOC_REQUEST_HIGH_PRIORITY:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_request_high_priority_s), sizeof(u64)));
+		err = request_high_priority_wrapper(session_data, (_mali_uk_request_high_priority_s __user *)arg);
+		break;
+
+	case MALI_IOC_PENDING_SUBMIT:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_pending_submit_s), sizeof(u64)));
+		err = pending_submit_wrapper(session_data, (_mali_uk_pending_submit_s __user *)arg);
+		break;
+
+#if defined(CONFIG_MALI400_PROFILING)
+	case MALI_IOC_PROFILING_ADD_EVENT:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_profiling_add_event_s), sizeof(u64)));
+		err = profiling_add_event_wrapper(session_data, (_mali_uk_profiling_add_event_s __user *)arg);
+		break;
+
+	case MALI_IOC_PROFILING_REPORT_SW_COUNTERS:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_sw_counters_report_s), sizeof(u64)));
+		err = profiling_report_sw_counters_wrapper(session_data, (_mali_uk_sw_counters_report_s __user *)arg);
+		break;
+
+	case MALI_IOC_PROFILING_STREAM_FD_GET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_profiling_stream_fd_get_s), sizeof(u64)));
+		err = profiling_get_stream_fd_wrapper(session_data, (_mali_uk_profiling_stream_fd_get_s __user *)arg);
+		break;
+
+	case MALI_IOC_PROILING_CONTROL_SET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_profiling_control_set_s), sizeof(u64)));
+		err = profiling_control_set_wrapper(session_data, (_mali_uk_profiling_control_set_s __user *)arg);
+		break;
+#else
+
+	case MALI_IOC_PROFILING_ADD_EVENT:          /* FALL-THROUGH */
+	case MALI_IOC_PROFILING_REPORT_SW_COUNTERS: /* FALL-THROUGH */
+		MALI_DEBUG_PRINT(2, ("Profiling not supported\n"));
+		err = -ENOTTY;
+		break;
+#endif
+
+	case MALI_IOC_PROFILING_MEMORY_USAGE_GET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_profiling_memory_usage_get_s), sizeof(u64)));
+		err = mem_usage_get_wrapper(session_data, (_mali_uk_profiling_memory_usage_get_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_ALLOC:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_alloc_mem_s), sizeof(u64)));
+		err = mem_alloc_wrapper(session_data, (_mali_uk_alloc_mem_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_FREE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_free_mem_s), sizeof(u64)));
+		err = mem_free_wrapper(session_data, (_mali_uk_free_mem_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_BIND:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_bind_mem_s), sizeof(u64)));
+		err = mem_bind_wrapper(session_data, (_mali_uk_bind_mem_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_UNBIND:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_unbind_mem_s), sizeof(u64)));
+		err = mem_unbind_wrapper(session_data, (_mali_uk_unbind_mem_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_COW:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_cow_mem_s), sizeof(u64)));
+		err = mem_cow_wrapper(session_data, (_mali_uk_cow_mem_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_COW_MODIFY_RANGE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_cow_modify_range_s), sizeof(u64)));
+		err = mem_cow_modify_range_wrapper(session_data, (_mali_uk_cow_modify_range_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_RESIZE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_mem_resize_s), sizeof(u64)));
+		err = mem_resize_mem_wrapper(session_data, (_mali_uk_mem_resize_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_WRITE_SAFE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_mem_write_safe_s), sizeof(u64)));
+		err = mem_write_safe_wrapper(session_data, (_mali_uk_mem_write_safe_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_QUERY_MMU_PAGE_TABLE_DUMP_SIZE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_query_mmu_page_table_dump_size_s), sizeof(u64)));
+		err = mem_query_mmu_page_table_dump_size_wrapper(session_data, (_mali_uk_query_mmu_page_table_dump_size_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_DUMP_MMU_PAGE_TABLE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_dump_mmu_page_table_s), sizeof(u64)));
+		err = mem_dump_mmu_page_table_wrapper(session_data, (_mali_uk_dump_mmu_page_table_s __user *)arg);
+		break;
+
+	case MALI_IOC_MEM_DMA_BUF_GET_SIZE:
+#ifdef CONFIG_DMA_SHARED_BUFFER
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_dma_buf_get_size_s), sizeof(u64)));
+		err = mali_dma_buf_get_size(session_data, (_mali_uk_dma_buf_get_size_s __user *)arg);
+#else
+		MALI_DEBUG_PRINT(2, ("DMA-BUF not supported\n"));
+		err = -ENOTTY;
+#endif
+		break;
+
+	case MALI_IOC_PP_START_JOB:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_pp_start_job_s), sizeof(u64)));
+		err = pp_start_job_wrapper(session_data, (_mali_uk_pp_start_job_s __user *)arg);
+		break;
+
+	case MALI_IOC_PP_AND_GP_START_JOB:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_pp_and_gp_start_job_s), sizeof(u64)));
+		err = pp_and_gp_start_job_wrapper(session_data, (_mali_uk_pp_and_gp_start_job_s __user *)arg);
+		break;
+
+	case MALI_IOC_PP_NUMBER_OF_CORES_GET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_get_pp_number_of_cores_s), sizeof(u64)));
+		err = pp_get_number_of_cores_wrapper(session_data, (_mali_uk_get_pp_number_of_cores_s __user *)arg);
+		break;
+
+	case MALI_IOC_PP_CORE_VERSION_GET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_get_pp_core_version_s), sizeof(u64)));
+		err = pp_get_core_version_wrapper(session_data, (_mali_uk_get_pp_core_version_s __user *)arg);
+		break;
+
+	case MALI_IOC_PP_DISABLE_WB:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_pp_disable_wb_s), sizeof(u64)));
+		err = pp_disable_wb_wrapper(session_data, (_mali_uk_pp_disable_wb_s __user *)arg);
+		break;
+
+	case MALI_IOC_GP2_START_JOB:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_gp_start_job_s), sizeof(u64)));
+		err = gp_start_job_wrapper(session_data, (_mali_uk_gp_start_job_s __user *)arg);
+		break;
+
+	case MALI_IOC_GP2_NUMBER_OF_CORES_GET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_get_gp_number_of_cores_s), sizeof(u64)));
+		err = gp_get_number_of_cores_wrapper(session_data, (_mali_uk_get_gp_number_of_cores_s __user *)arg);
+		break;
+
+	case MALI_IOC_GP2_CORE_VERSION_GET:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_get_gp_core_version_s), sizeof(u64)));
+		err = gp_get_core_version_wrapper(session_data, (_mali_uk_get_gp_core_version_s __user *)arg);
+		break;
+
+	case MALI_IOC_GP2_SUSPEND_RESPONSE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_gp_suspend_response_s), sizeof(u64)));
+		err = gp_suspend_response_wrapper(session_data, (_mali_uk_gp_suspend_response_s __user *)arg);
+		break;
+
+	case MALI_IOC_VSYNC_EVENT_REPORT:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_vsync_event_report_s), sizeof(u64)));
+		err = vsync_event_report_wrapper(session_data, (_mali_uk_vsync_event_report_s __user *)arg);
+		break;
+
+	case MALI_IOC_TIMELINE_GET_LATEST_POINT:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_timeline_get_latest_point_s), sizeof(u64)));
+		err = timeline_get_latest_point_wrapper(session_data, (_mali_uk_timeline_get_latest_point_s __user *)arg);
+		break;
+	case MALI_IOC_TIMELINE_WAIT:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_timeline_wait_s), sizeof(u64)));
+		err = timeline_wait_wrapper(session_data, (_mali_uk_timeline_wait_s __user *)arg);
+		break;
+	case MALI_IOC_TIMELINE_CREATE_SYNC_FENCE:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_timeline_create_sync_fence_s), sizeof(u64)));
+		err = timeline_create_sync_fence_wrapper(session_data, (_mali_uk_timeline_create_sync_fence_s __user *)arg);
+		break;
+	case MALI_IOC_SOFT_JOB_START:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_soft_job_start_s), sizeof(u64)));
+		err = soft_job_start_wrapper(session_data, (_mali_uk_soft_job_start_s __user *)arg);
+		break;
+	case MALI_IOC_SOFT_JOB_SIGNAL:
+		BUILD_BUG_ON(!IS_ALIGNED(sizeof(_mali_uk_soft_job_signal_s), sizeof(u64)));
+		err = soft_job_signal_wrapper(session_data, (_mali_uk_soft_job_signal_s __user *)arg);
+		break;
+
+	default:
+		MALI_DEBUG_PRINT(2, ("No handler for ioctl 0x%08X 0x%08lX\n", cmd, arg));
+		err = -ENOTTY;
+	};
+
+	return err;
+}
+
+
+module_init(mali_module_init);
+module_exit(mali_module_exit);
+
+MODULE_LICENSE(MALI_KERNEL_LINUX_LICENSE);
+MODULE_AUTHOR("ARM Ltd.");
+MODULE_VERSION(SVN_REV_STRING);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_kernel_linux.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_kernel_linux.h
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_KERNEL_LINUX_H__
+#define __MALI_KERNEL_LINUX_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include <linux/cdev.h>     /* character device definitions */
+#include <linux/idr.h>
+#include <linux/rbtree.h>
+#include "mali_kernel_license.h"
+#include "mali_osk_types.h"
+#include <linux/version.h>
+
+extern struct platform_device *mali_platform_device;
+
+/* After 3.19.0 kenrel droped CONFIG_PM_RUNTIME define,define by ourself */
+#if defined(CONFIG_PM) && LINUX_VERSION_CODE >= KERNEL_VERSION(3, 19, 0)
+#define CONFIG_PM_RUNTIME 1
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_KERNEL_LINUX_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_kernel_sysfs.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_kernel_sysfs.c
@@ -0,0 +1,1415 @@
+/**
+ * Copyright (C) 2011-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+
+/**
+ * @file mali_kernel_sysfs.c
+ * Implementation of some sysfs data exports
+ */
+
+#include <linux/kernel.h>
+#include <linux/fs.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include "mali_kernel_license.h"
+#include "mali_kernel_common.h"
+#include "mali_ukk.h"
+
+#if MALI_LICENSE_IS_GPL
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+#include <linux/module.h>
+#include <linux/mali/mali_utgard.h>
+#include "mali_kernel_sysfs.h"
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+#include <linux/slab.h>
+#include "mali_osk_profiling.h"
+#endif
+
+#include <linux/mali/mali_utgard.h>
+#include "mali_pm.h"
+#include "mali_pmu.h"
+#include "mali_group.h"
+#include "mali_gp.h"
+#include "mali_pp.h"
+#include "mali_l2_cache.h"
+#include "mali_hw_core.h"
+#include "mali_kernel_core.h"
+#include "mali_user_settings_db.h"
+#include "mali_profiling_internal.h"
+#include "mali_gp_job.h"
+#include "mali_pp_job.h"
+#include "mali_executor.h"
+
+#define PRIVATE_DATA_COUNTER_MAKE_GP(src) (src)
+#define PRIVATE_DATA_COUNTER_MAKE_PP(src) ((1 << 24) | src)
+#define PRIVATE_DATA_COUNTER_MAKE_PP_SUB_JOB(src, sub_job) ((1 << 24) | (1 << 16) | (sub_job << 8) | src)
+#define PRIVATE_DATA_COUNTER_IS_PP(a) ((((a) >> 24) & 0xFF) ? MALI_TRUE : MALI_FALSE)
+#define PRIVATE_DATA_COUNTER_GET_SRC(a) (a & 0xFF)
+#define PRIVATE_DATA_COUNTER_IS_SUB_JOB(a) ((((a) >> 16) & 0xFF) ? MALI_TRUE : MALI_FALSE)
+#define PRIVATE_DATA_COUNTER_GET_SUB_JOB(a) (((a) >> 8) & 0xFF)
+
+#define POWER_BUFFER_SIZE 3
+
+static struct dentry *mali_debugfs_dir = NULL;
+
+typedef enum {
+	_MALI_DEVICE_SUSPEND,
+	_MALI_DEVICE_RESUME,
+	_MALI_DEVICE_DVFS_PAUSE,
+	_MALI_DEVICE_DVFS_RESUME,
+	_MALI_MAX_EVENTS
+} _mali_device_debug_power_events;
+
+static const char *const mali_power_events[_MALI_MAX_EVENTS] = {
+	[_MALI_DEVICE_SUSPEND] = "suspend",
+	[_MALI_DEVICE_RESUME] = "resume",
+	[_MALI_DEVICE_DVFS_PAUSE] = "dvfs_pause",
+	[_MALI_DEVICE_DVFS_RESUME] = "dvfs_resume",
+};
+
+static mali_bool power_always_on_enabled = MALI_FALSE;
+
+static int open_copy_private_data(struct inode *inode, struct file *filp)
+{
+	filp->private_data = inode->i_private;
+	return 0;
+}
+
+static ssize_t group_enabled_read(struct file *filp, char __user *buf, size_t count, loff_t *offp)
+{
+	int r;
+	char buffer[64];
+	struct mali_group *group;
+
+	group = (struct mali_group *)filp->private_data;
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	r = snprintf(buffer, 64, "%u\n",
+		     mali_executor_group_is_disabled(group) ? 0 : 1);
+
+	return simple_read_from_buffer(buf, count, offp, buffer, r);
+}
+
+static ssize_t group_enabled_write(struct file *filp, const char __user *buf, size_t count, loff_t *offp)
+{
+	int r;
+	char buffer[64];
+	unsigned long val;
+	struct mali_group *group;
+
+	group = (struct mali_group *)filp->private_data;
+	MALI_DEBUG_ASSERT_POINTER(group);
+
+	if (count >= sizeof(buffer)) {
+		return -ENOMEM;
+	}
+
+	if (copy_from_user(&buffer[0], buf, count)) {
+		return -EFAULT;
+	}
+	buffer[count] = '\0';
+
+	r = kstrtoul(&buffer[0], 10, &val);
+	if (0 != r) {
+		return -EINVAL;
+	}
+
+	switch (val) {
+	case 1:
+		mali_executor_group_enable(group);
+		break;
+	case 0:
+		mali_executor_group_disable(group);
+		break;
+	default:
+		return -EINVAL;
+		break;
+	}
+
+	*offp += count;
+	return count;
+}
+
+static const struct file_operations group_enabled_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read = group_enabled_read,
+	.write = group_enabled_write,
+};
+
+static ssize_t hw_core_base_addr_read(struct file *filp, char __user *buf, size_t count, loff_t *offp)
+{
+	int r;
+	char buffer[64];
+	struct mali_hw_core *hw_core;
+
+	hw_core = (struct mali_hw_core *)filp->private_data;
+	MALI_DEBUG_ASSERT_POINTER(hw_core);
+
+	r = snprintf(buffer, 64, "0x%lX\n", hw_core->phys_addr);
+
+	return simple_read_from_buffer(buf, count, offp, buffer, r);
+}
+
+static const struct file_operations hw_core_base_addr_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read = hw_core_base_addr_read,
+};
+
+static ssize_t profiling_counter_src_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	u32 is_pp = PRIVATE_DATA_COUNTER_IS_PP((uintptr_t)filp->private_data);
+	u32 src_id = PRIVATE_DATA_COUNTER_GET_SRC((uintptr_t)filp->private_data);
+	mali_bool is_sub_job = PRIVATE_DATA_COUNTER_IS_SUB_JOB((uintptr_t)filp->private_data);
+	u32 sub_job = PRIVATE_DATA_COUNTER_GET_SUB_JOB((uintptr_t)filp->private_data);
+	char buf[64];
+	int r;
+	u32 val;
+
+	if (MALI_TRUE == is_pp) {
+		/* PP counter */
+		if (MALI_TRUE == is_sub_job) {
+			/* Get counter for a particular sub job */
+			if (0 == src_id) {
+				val = mali_pp_job_get_pp_counter_sub_job_src0(sub_job);
+			} else {
+				val = mali_pp_job_get_pp_counter_sub_job_src1(sub_job);
+			}
+		} else {
+			/* Get default counter for all PP sub jobs */
+			if (0 == src_id) {
+				val = mali_pp_job_get_pp_counter_global_src0();
+			} else {
+				val = mali_pp_job_get_pp_counter_global_src1();
+			}
+		}
+	} else {
+		/* GP counter */
+		if (0 == src_id) {
+			val = mali_gp_job_get_gp_counter_src0();
+		} else {
+			val = mali_gp_job_get_gp_counter_src1();
+		}
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER == val) {
+		r = snprintf(buf, 64, "-1\n");
+	} else {
+		r = snprintf(buf, 64, "%u\n", val);
+	}
+
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static ssize_t profiling_counter_src_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	u32 is_pp = PRIVATE_DATA_COUNTER_IS_PP((uintptr_t)filp->private_data);
+	u32 src_id = PRIVATE_DATA_COUNTER_GET_SRC((uintptr_t)filp->private_data);
+	mali_bool is_sub_job = PRIVATE_DATA_COUNTER_IS_SUB_JOB((uintptr_t)filp->private_data);
+	u32 sub_job = PRIVATE_DATA_COUNTER_GET_SUB_JOB((uintptr_t)filp->private_data);
+	char buf[64];
+	long val;
+	int ret;
+
+	if (cnt >= sizeof(buf)) {
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&buf, ubuf, cnt)) {
+		return -EFAULT;
+	}
+
+	buf[cnt] = 0;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret < 0) {
+		return ret;
+	}
+
+	if (val < 0) {
+		/* any negative input will disable counter */
+		val = MALI_HW_CORE_NO_COUNTER;
+	}
+
+	if (MALI_TRUE == is_pp) {
+		/* PP counter */
+		if (MALI_TRUE == is_sub_job) {
+			/* Set counter for a particular sub job */
+			if (0 == src_id) {
+				mali_pp_job_set_pp_counter_sub_job_src0(sub_job, (u32)val);
+			} else {
+				mali_pp_job_set_pp_counter_sub_job_src1(sub_job, (u32)val);
+			}
+		} else {
+			/* Set default counter for all PP sub jobs */
+			if (0 == src_id) {
+				mali_pp_job_set_pp_counter_global_src0((u32)val);
+			} else {
+				mali_pp_job_set_pp_counter_global_src1((u32)val);
+			}
+		}
+	} else {
+		/* GP counter */
+		if (0 == src_id) {
+			mali_gp_job_set_gp_counter_src0((u32)val);
+		} else {
+			mali_gp_job_set_gp_counter_src1((u32)val);
+		}
+	}
+
+	*ppos += cnt;
+	return cnt;
+}
+
+static const struct file_operations profiling_counter_src_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read  = profiling_counter_src_read,
+	.write = profiling_counter_src_write,
+};
+
+static ssize_t l2_l2x_counter_srcx_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos, u32 src_id)
+{
+	char buf[64];
+	int r;
+	u32 val;
+	struct mali_l2_cache_core *l2_core = (struct mali_l2_cache_core *)filp->private_data;
+
+	if (0 == src_id) {
+		val = mali_l2_cache_core_get_counter_src0(l2_core);
+	} else {
+		val = mali_l2_cache_core_get_counter_src1(l2_core);
+	}
+
+	if (MALI_HW_CORE_NO_COUNTER == val) {
+		r = snprintf(buf, 64, "-1\n");
+	} else {
+		r = snprintf(buf, 64, "%u\n", val);
+	}
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static ssize_t l2_l2x_counter_srcx_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos, u32 src_id)
+{
+	struct mali_l2_cache_core *l2_core = (struct mali_l2_cache_core *)filp->private_data;
+	char buf[64];
+	long val;
+	int ret;
+
+	if (cnt >= sizeof(buf)) {
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&buf, ubuf, cnt)) {
+		return -EFAULT;
+	}
+
+	buf[cnt] = 0;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret < 0) {
+		return ret;
+	}
+
+	if (val < 0) {
+		/* any negative input will disable counter */
+		val = MALI_HW_CORE_NO_COUNTER;
+	}
+
+	mali_l2_cache_core_set_counter_src(l2_core, src_id, (u32)val);
+
+	*ppos += cnt;
+	return cnt;
+}
+
+static ssize_t l2_all_counter_srcx_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos, u32 src_id)
+{
+	char buf[64];
+	long val;
+	int ret;
+	u32 l2_id;
+	struct mali_l2_cache_core *l2_cache;
+
+	if (cnt >= sizeof(buf)) {
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&buf, ubuf, cnt)) {
+		return -EFAULT;
+	}
+
+	buf[cnt] = 0;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret < 0) {
+		return ret;
+	}
+
+	if (val < 0) {
+		/* any negative input will disable counter */
+		val = MALI_HW_CORE_NO_COUNTER;
+	}
+
+	l2_id = 0;
+	l2_cache = mali_l2_cache_core_get_glob_l2_core(l2_id);
+	while (NULL != l2_cache) {
+		mali_l2_cache_core_set_counter_src(l2_cache, src_id, (u32)val);
+
+		/* try next L2 */
+		l2_id++;
+		l2_cache = mali_l2_cache_core_get_glob_l2_core(l2_id);
+	}
+
+	*ppos += cnt;
+	return cnt;
+}
+
+static ssize_t l2_l2x_counter_src0_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_l2x_counter_srcx_read(filp, ubuf, cnt, ppos, 0);
+}
+
+static ssize_t l2_l2x_counter_src1_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_l2x_counter_srcx_read(filp, ubuf, cnt, ppos, 1);
+}
+
+static ssize_t l2_l2x_counter_src0_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_l2x_counter_srcx_write(filp, ubuf, cnt, ppos, 0);
+}
+
+static ssize_t l2_l2x_counter_src1_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_l2x_counter_srcx_write(filp, ubuf, cnt, ppos, 1);
+}
+
+static ssize_t l2_all_counter_src0_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_all_counter_srcx_write(filp, ubuf, cnt, ppos, 0);
+}
+
+static ssize_t l2_all_counter_src1_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_all_counter_srcx_write(filp, ubuf, cnt, ppos, 1);
+}
+
+static const struct file_operations l2_l2x_counter_src0_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read  = l2_l2x_counter_src0_read,
+	.write = l2_l2x_counter_src0_write,
+};
+
+static const struct file_operations l2_l2x_counter_src1_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read  = l2_l2x_counter_src1_read,
+	.write = l2_l2x_counter_src1_write,
+};
+
+static const struct file_operations l2_all_counter_src0_fops = {
+	.owner = THIS_MODULE,
+	.write = l2_all_counter_src0_write,
+};
+
+static const struct file_operations l2_all_counter_src1_fops = {
+	.owner = THIS_MODULE,
+	.write = l2_all_counter_src1_write,
+};
+
+static ssize_t l2_l2x_counter_valx_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos, u32 src_id)
+{
+	char buf[64];
+	int r;
+	u32 src0 = 0;
+	u32 val0 = 0;
+	u32 src1 = 0;
+	u32 val1 = 0;
+	u32 val = -1;
+	struct mali_l2_cache_core *l2_core = (struct mali_l2_cache_core *)filp->private_data;
+
+	mali_l2_cache_core_get_counter_values(l2_core, &src0, &val0, &src1, &val1);
+
+	if (0 == src_id) {
+		if (MALI_HW_CORE_NO_COUNTER != val0) {
+			val = val0;
+		}
+	} else {
+		if (MALI_HW_CORE_NO_COUNTER != val1) {
+			val = val1;
+		}
+	}
+
+	r = snprintf(buf, 64, "%u\n", val);
+
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static ssize_t l2_l2x_counter_val0_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_l2x_counter_valx_read(filp, ubuf, cnt, ppos, 0);
+}
+
+static ssize_t l2_l2x_counter_val1_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	return l2_l2x_counter_valx_read(filp, ubuf, cnt, ppos, 1);
+}
+
+static const struct file_operations l2_l2x_counter_val0_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read  = l2_l2x_counter_val0_read,
+};
+
+static const struct file_operations l2_l2x_counter_val1_fops = {
+	.owner = THIS_MODULE,
+	.open  = open_copy_private_data,
+	.read  = l2_l2x_counter_val1_read,
+};
+
+static ssize_t power_always_on_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	unsigned long val;
+	int ret;
+	char buf[32];
+
+	cnt = min(cnt, sizeof(buf) - 1);
+	if (copy_from_user(buf, ubuf, cnt)) {
+		return -EFAULT;
+	}
+	buf[cnt] = '\0';
+
+	ret = kstrtoul(buf, 10, &val);
+	if (0 != ret) {
+		return ret;
+	}
+
+	/* Update setting (not exactly thread safe) */
+	if (1 == val && MALI_FALSE == power_always_on_enabled) {
+		power_always_on_enabled = MALI_TRUE;
+		_mali_osk_pm_dev_ref_get_sync();
+	} else if (0 == val && MALI_TRUE == power_always_on_enabled) {
+		power_always_on_enabled = MALI_FALSE;
+		_mali_osk_pm_dev_ref_put();
+	}
+
+	*ppos += cnt;
+	return cnt;
+}
+
+static ssize_t power_always_on_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	if (MALI_TRUE == power_always_on_enabled) {
+		return simple_read_from_buffer(ubuf, cnt, ppos, "1\n", 2);
+	} else {
+		return simple_read_from_buffer(ubuf, cnt, ppos, "0\n", 2);
+	}
+}
+
+static const struct file_operations power_always_on_fops = {
+	.owner = THIS_MODULE,
+	.read  = power_always_on_read,
+	.write = power_always_on_write,
+};
+
+static ssize_t power_power_events_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	if (!strncmp(ubuf, mali_power_events[_MALI_DEVICE_SUSPEND], strlen(mali_power_events[_MALI_DEVICE_SUSPEND]) - 1)) {
+		mali_pm_os_suspend(MALI_TRUE);
+	} else if (!strncmp(ubuf, mali_power_events[_MALI_DEVICE_RESUME], strlen(mali_power_events[_MALI_DEVICE_RESUME]) - 1)) {
+		mali_pm_os_resume();
+	} else if (!strncmp(ubuf, mali_power_events[_MALI_DEVICE_DVFS_PAUSE], strlen(mali_power_events[_MALI_DEVICE_DVFS_PAUSE]) - 1)) {
+		mali_dev_pause();
+	} else if (!strncmp(ubuf, mali_power_events[_MALI_DEVICE_DVFS_RESUME], strlen(mali_power_events[_MALI_DEVICE_DVFS_RESUME]) - 1)) {
+		mali_dev_resume();
+	}
+	*ppos += cnt;
+	return cnt;
+}
+
+static loff_t power_power_events_seek(struct file *file, loff_t offset, int orig)
+{
+	file->f_pos = offset;
+	return 0;
+}
+
+static const struct file_operations power_power_events_fops = {
+	.owner = THIS_MODULE,
+	.write = power_power_events_write,
+	.llseek = power_power_events_seek,
+};
+
+#if MALI_STATE_TRACKING
+static int mali_seq_internal_state_show(struct seq_file *seq_file, void *v)
+{
+	u32 len = 0;
+	u32 size;
+	char *buf;
+
+	size = seq_get_buf(seq_file, &buf);
+
+	if (!size) {
+		return -ENOMEM;
+	}
+
+	/* Create the internal state dump. */
+	len  = snprintf(buf + len, size - len, "Mali device driver %s\n", SVN_REV_STRING);
+	len += snprintf(buf + len, size - len, "License: %s\n\n", MALI_KERNEL_LINUX_LICENSE);
+
+	len += _mali_kernel_core_dump_state(buf + len, size - len);
+
+	seq_commit(seq_file, len);
+
+	return 0;
+}
+
+static int mali_seq_internal_state_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, mali_seq_internal_state_show, NULL);
+}
+
+static const struct file_operations mali_seq_internal_state_fops = {
+	.owner = THIS_MODULE,
+	.open = mali_seq_internal_state_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+#endif /* MALI_STATE_TRACKING */
+
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+static ssize_t profiling_record_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	char buf[64];
+	int r;
+
+	r = snprintf(buf, 64, "%u\n", _mali_internal_profiling_is_recording() ? 1 : 0);
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static ssize_t profiling_record_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	char buf[64];
+	unsigned long val;
+	int ret;
+
+	if (cnt >= sizeof(buf)) {
+		return -EINVAL;
+	}
+
+	if (copy_from_user(&buf, ubuf, cnt)) {
+		return -EFAULT;
+	}
+
+	buf[cnt] = 0;
+
+	ret = kstrtoul(buf, 10, &val);
+	if (ret < 0) {
+		return ret;
+	}
+
+	if (val != 0) {
+		u32 limit = MALI_PROFILING_MAX_BUFFER_ENTRIES; /* This can be made configurable at a later stage if we need to */
+
+		/* check if we are already recording */
+		if (MALI_TRUE == _mali_internal_profiling_is_recording()) {
+			MALI_DEBUG_PRINT(3, ("Recording of profiling events already in progress\n"));
+			return -EFAULT;
+		}
+
+		/* check if we need to clear out an old recording first */
+		if (MALI_TRUE == _mali_internal_profiling_have_recording()) {
+			if (_MALI_OSK_ERR_OK != _mali_internal_profiling_clear()) {
+				MALI_DEBUG_PRINT(3, ("Failed to clear existing recording of profiling events\n"));
+				return -EFAULT;
+			}
+		}
+
+		/* start recording profiling data */
+		if (_MALI_OSK_ERR_OK != _mali_internal_profiling_start(&limit)) {
+			MALI_DEBUG_PRINT(3, ("Failed to start recording of profiling events\n"));
+			return -EFAULT;
+		}
+
+		MALI_DEBUG_PRINT(3, ("Profiling recording started (max %u events)\n", limit));
+	} else {
+		/* stop recording profiling data */
+		u32 count = 0;
+		if (_MALI_OSK_ERR_OK != _mali_internal_profiling_stop(&count)) {
+			MALI_DEBUG_PRINT(2, ("Failed to stop recording of profiling events\n"));
+			return -EFAULT;
+		}
+
+		MALI_DEBUG_PRINT(2, ("Profiling recording stopped (recorded %u events)\n", count));
+	}
+
+	*ppos += cnt;
+	return cnt;
+}
+
+static const struct file_operations profiling_record_fops = {
+	.owner = THIS_MODULE,
+	.read  = profiling_record_read,
+	.write = profiling_record_write,
+};
+
+static void *profiling_events_start(struct seq_file *s, loff_t *pos)
+{
+	loff_t *spos;
+
+	/* check if we have data avaiable */
+	if (MALI_TRUE != _mali_internal_profiling_have_recording()) {
+		return NULL;
+	}
+
+	spos = kmalloc(sizeof(loff_t), GFP_KERNEL);
+	if (NULL == spos) {
+		return NULL;
+	}
+
+	*spos = *pos;
+	return spos;
+}
+
+static void *profiling_events_next(struct seq_file *s, void *v, loff_t *pos)
+{
+	loff_t *spos = v;
+
+	/* check if we have data avaiable */
+	if (MALI_TRUE != _mali_internal_profiling_have_recording()) {
+		return NULL;
+	}
+
+	/* check if the next entry actually is avaiable */
+	if (_mali_internal_profiling_get_count() <= (u32)(*spos + 1)) {
+		return NULL;
+	}
+
+	*pos = ++*spos;
+	return spos;
+}
+
+static void profiling_events_stop(struct seq_file *s, void *v)
+{
+	kfree(v);
+}
+
+static int profiling_events_show(struct seq_file *seq_file, void *v)
+{
+	loff_t *spos = v;
+	u32 index;
+	u64 timestamp;
+	u32 event_id;
+	u32 data[5];
+
+	index = (u32) * spos;
+
+	/* Retrieve all events */
+	if (_MALI_OSK_ERR_OK == _mali_internal_profiling_get_event(index, &timestamp, &event_id, data)) {
+		seq_printf(seq_file, "%llu %u %u %u %u %u %u\n", timestamp, event_id, data[0], data[1], data[2], data[3], data[4]);
+		return 0;
+	}
+
+	return 0;
+}
+
+static int profiling_events_show_human_readable(struct seq_file *seq_file, void *v)
+{
+#define MALI_EVENT_ID_IS_HW(event_id) (((event_id & 0x00FF0000) >= MALI_PROFILING_EVENT_CHANNEL_GP0) && ((event_id & 0x00FF0000) <= MALI_PROFILING_EVENT_CHANNEL_PP7))
+
+	static u64 start_time = 0;
+	loff_t *spos = v;
+	u32 index;
+	u64 timestamp;
+	u32 event_id;
+	u32 data[5];
+
+	index = (u32) * spos;
+
+	/* Retrieve all events */
+	if (_MALI_OSK_ERR_OK == _mali_internal_profiling_get_event(index, &timestamp, &event_id, data)) {
+		seq_printf(seq_file, "%llu %u %u %u %u %u %u # ", timestamp, event_id, data[0], data[1], data[2], data[3], data[4]);
+
+		if (0 == index) {
+			start_time = timestamp;
+		}
+
+		seq_printf(seq_file, "[%06u] ", index);
+
+		switch (event_id & 0x0F000000) {
+		case MALI_PROFILING_EVENT_TYPE_SINGLE:
+			seq_printf(seq_file, "SINGLE | ");
+			break;
+		case MALI_PROFILING_EVENT_TYPE_START:
+			seq_printf(seq_file, "START | ");
+			break;
+		case MALI_PROFILING_EVENT_TYPE_STOP:
+			seq_printf(seq_file, "STOP | ");
+			break;
+		case MALI_PROFILING_EVENT_TYPE_SUSPEND:
+			seq_printf(seq_file, "SUSPEND | ");
+			break;
+		case MALI_PROFILING_EVENT_TYPE_RESUME:
+			seq_printf(seq_file, "RESUME | ");
+			break;
+		default:
+			seq_printf(seq_file, "0x%01X | ", (event_id & 0x0F000000) >> 24);
+			break;
+		}
+
+		switch (event_id & 0x00FF0000) {
+		case MALI_PROFILING_EVENT_CHANNEL_SOFTWARE:
+			seq_printf(seq_file, "SW | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_GP0:
+			seq_printf(seq_file, "GP0 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP0:
+			seq_printf(seq_file, "PP0 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP1:
+			seq_printf(seq_file, "PP1 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP2:
+			seq_printf(seq_file, "PP2 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP3:
+			seq_printf(seq_file, "PP3 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP4:
+			seq_printf(seq_file, "PP4 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP5:
+			seq_printf(seq_file, "PP5 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP6:
+			seq_printf(seq_file, "PP6 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_PP7:
+			seq_printf(seq_file, "PP7 | ");
+			break;
+		case MALI_PROFILING_EVENT_CHANNEL_GPU:
+			seq_printf(seq_file, "GPU | ");
+			break;
+		default:
+			seq_printf(seq_file, "0x%02X | ", (event_id & 0x00FF0000) >> 16);
+			break;
+		}
+
+		if (MALI_EVENT_ID_IS_HW(event_id)) {
+			if (((event_id & 0x0F000000) == MALI_PROFILING_EVENT_TYPE_START) || ((event_id & 0x0F000000) == MALI_PROFILING_EVENT_TYPE_STOP)) {
+				switch (event_id & 0x0000FFFF) {
+				case MALI_PROFILING_EVENT_REASON_START_STOP_HW_PHYSICAL:
+					seq_printf(seq_file, "PHYSICAL | ");
+					break;
+				case MALI_PROFILING_EVENT_REASON_START_STOP_HW_VIRTUAL:
+					seq_printf(seq_file, "VIRTUAL | ");
+					break;
+				default:
+					seq_printf(seq_file, "0x%04X | ", event_id & 0x0000FFFF);
+					break;
+				}
+			} else {
+				seq_printf(seq_file, "0x%04X | ", event_id & 0x0000FFFF);
+			}
+		} else {
+			seq_printf(seq_file, "0x%04X | ", event_id & 0x0000FFFF);
+		}
+
+		seq_printf(seq_file, "T0 + 0x%016llX\n", timestamp - start_time);
+
+		return 0;
+	}
+
+	return 0;
+}
+
+static const struct seq_operations profiling_events_seq_ops = {
+	.start = profiling_events_start,
+	.next  = profiling_events_next,
+	.stop  = profiling_events_stop,
+	.show  = profiling_events_show
+};
+
+static int profiling_events_open(struct inode *inode, struct file *file)
+{
+	return seq_open(file, &profiling_events_seq_ops);
+}
+
+static const struct file_operations profiling_events_fops = {
+	.owner = THIS_MODULE,
+	.open = profiling_events_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = seq_release,
+};
+
+static const struct seq_operations profiling_events_human_readable_seq_ops = {
+	.start = profiling_events_start,
+	.next  = profiling_events_next,
+	.stop  = profiling_events_stop,
+	.show  = profiling_events_show_human_readable
+};
+
+static int profiling_events_human_readable_open(struct inode *inode, struct file *file)
+{
+	return seq_open(file, &profiling_events_human_readable_seq_ops);
+}
+
+static const struct file_operations profiling_events_human_readable_fops = {
+	.owner = THIS_MODULE,
+	.open = profiling_events_human_readable_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = seq_release,
+};
+
+#endif
+
+static int memory_debugfs_show(struct seq_file *s, void *private_data)
+{
+#ifdef MALI_MEM_SWAP_TRACKING
+	seq_printf(s, "  %-25s  %-10s  %-10s  %-15s  %-15s  %-10s  %-10s %-10s \n"\
+		   "=================================================================================================================================\n",
+		   "Name (:bytes)", "pid", "mali_mem", "max_mali_mem",
+		   "external_mem", "ump_mem", "dma_mem", "swap_mem");
+#else
+	seq_printf(s, "  %-25s  %-10s  %-10s  %-15s  %-15s  %-10s  %-10s \n"\
+		   "========================================================================================================================\n",
+		   "Name (:bytes)", "pid", "mali_mem", "max_mali_mem",
+		   "external_mem", "ump_mem", "dma_mem");
+#endif
+	mali_session_memory_tracking(s);
+	return 0;
+}
+
+static int memory_debugfs_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, memory_debugfs_show, inode->i_private);
+}
+
+static const struct file_operations memory_usage_fops = {
+	.owner = THIS_MODULE,
+	.open = memory_debugfs_open,
+	.read  = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+
+static ssize_t utilization_gp_pp_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	char buf[64];
+	size_t r;
+	u32 uval = _mali_ukk_utilization_gp_pp();
+
+	r = snprintf(buf, 64, "%u\n", uval);
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static ssize_t utilization_gp_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	char buf[64];
+	size_t r;
+	u32 uval = _mali_ukk_utilization_gp();
+
+	r = snprintf(buf, 64, "%u\n", uval);
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static ssize_t utilization_pp_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	char buf[64];
+	size_t r;
+	u32 uval = _mali_ukk_utilization_pp();
+
+	r = snprintf(buf, 64, "%u\n", uval);
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+
+static const struct file_operations utilization_gp_pp_fops = {
+	.owner = THIS_MODULE,
+	.read = utilization_gp_pp_read,
+};
+
+static const struct file_operations utilization_gp_fops = {
+	.owner = THIS_MODULE,
+	.read = utilization_gp_read,
+};
+
+static const struct file_operations utilization_pp_fops = {
+	.owner = THIS_MODULE,
+	.read = utilization_pp_read,
+};
+
+static ssize_t user_settings_write(struct file *filp, const char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	unsigned long val;
+	int ret;
+	_mali_uk_user_setting_t setting;
+	char buf[32];
+
+	cnt = min(cnt, sizeof(buf) - 1);
+	if (copy_from_user(buf, ubuf, cnt)) {
+		return -EFAULT;
+	}
+	buf[cnt] = '\0';
+
+	ret = kstrtoul(buf, 10, &val);
+	if (0 != ret) {
+		return ret;
+	}
+
+	/* Update setting */
+	setting = (_mali_uk_user_setting_t)(filp->private_data);
+	mali_set_user_setting(setting, val);
+
+	*ppos += cnt;
+	return cnt;
+}
+
+static ssize_t user_settings_read(struct file *filp, char __user *ubuf, size_t cnt, loff_t *ppos)
+{
+	char buf[64];
+	size_t r;
+	u32 value;
+	_mali_uk_user_setting_t setting;
+
+	setting = (_mali_uk_user_setting_t)(filp->private_data);
+	value = mali_get_user_setting(setting);
+
+	r = snprintf(buf, 64, "%u\n", value);
+	return simple_read_from_buffer(ubuf, cnt, ppos, buf, r);
+}
+
+static const struct file_operations user_settings_fops = {
+	.owner = THIS_MODULE,
+	.open = open_copy_private_data,
+	.read = user_settings_read,
+	.write = user_settings_write,
+};
+
+static int mali_sysfs_user_settings_register(void)
+{
+	struct dentry *mali_user_settings_dir = debugfs_create_dir("userspace_settings", mali_debugfs_dir);
+
+	if (mali_user_settings_dir != NULL) {
+		long i;
+		for (i = 0; i < _MALI_UK_USER_SETTING_MAX; i++) {
+			debugfs_create_file(_mali_uk_user_setting_descriptions[i],
+					    0600, mali_user_settings_dir, (void *)i,
+					    &user_settings_fops);
+		}
+	}
+
+	return 0;
+}
+
+static ssize_t pp_num_cores_enabled_write(struct file *filp, const char __user *buf, size_t count, loff_t *offp)
+{
+	int ret;
+	char buffer[32];
+	unsigned long val;
+
+	if (count >= sizeof(buffer)) {
+		return -ENOMEM;
+	}
+
+	if (copy_from_user(&buffer[0], buf, count)) {
+		return -EFAULT;
+	}
+	buffer[count] = '\0';
+
+	ret = kstrtoul(&buffer[0], 10, &val);
+	if (0 != ret) {
+		return -EINVAL;
+	}
+
+	ret = mali_executor_set_perf_level(val, MALI_TRUE); /* override even if core scaling is disabled */
+	if (ret) {
+		return ret;
+	}
+
+	*offp += count;
+	return count;
+}
+
+static ssize_t pp_num_cores_enabled_read(struct file *filp, char __user *buf, size_t count, loff_t *offp)
+{
+	int r;
+	char buffer[64];
+
+	r = snprintf(buffer, 64, "%u\n", mali_executor_get_num_cores_enabled());
+
+	return simple_read_from_buffer(buf, count, offp, buffer, r);
+}
+
+static const struct file_operations pp_num_cores_enabled_fops = {
+	.owner = THIS_MODULE,
+	.write = pp_num_cores_enabled_write,
+	.read = pp_num_cores_enabled_read,
+	.llseek = default_llseek,
+};
+
+static ssize_t pp_num_cores_total_read(struct file *filp, char __user *buf, size_t count, loff_t *offp)
+{
+	int r;
+	char buffer[64];
+
+	r = snprintf(buffer, 64, "%u\n", mali_executor_get_num_cores_total());
+
+	return simple_read_from_buffer(buf, count, offp, buffer, r);
+}
+
+static const struct file_operations pp_num_cores_total_fops = {
+	.owner = THIS_MODULE,
+	.read = pp_num_cores_total_read,
+};
+
+static ssize_t pp_core_scaling_enabled_write(struct file *filp, const char __user *buf, size_t count, loff_t *offp)
+{
+	int ret;
+	char buffer[32];
+	unsigned long val;
+
+	if (count >= sizeof(buffer)) {
+		return -ENOMEM;
+	}
+
+	if (copy_from_user(&buffer[0], buf, count)) {
+		return -EFAULT;
+	}
+	buffer[count] = '\0';
+
+	ret = kstrtoul(&buffer[0], 10, &val);
+	if (0 != ret) {
+		return -EINVAL;
+	}
+
+	switch (val) {
+	case 1:
+		mali_executor_core_scaling_enable();
+		break;
+	case 0:
+		mali_executor_core_scaling_disable();
+		break;
+	default:
+		return -EINVAL;
+		break;
+	}
+
+	*offp += count;
+	return count;
+}
+
+static ssize_t pp_core_scaling_enabled_read(struct file *filp, char __user *buf, size_t count, loff_t *offp)
+{
+	return simple_read_from_buffer(buf, count, offp, mali_executor_core_scaling_is_enabled() ? "1\n" : "0\n", 2);
+}
+static const struct file_operations pp_core_scaling_enabled_fops = {
+	.owner = THIS_MODULE,
+	.write = pp_core_scaling_enabled_write,
+	.read = pp_core_scaling_enabled_read,
+	.llseek = default_llseek,
+};
+
+static ssize_t version_read(struct file *filp, char __user *buf, size_t count, loff_t *offp)
+{
+	int r = 0;
+	char buffer[64];
+
+	switch (mali_kernel_core_get_product_id()) {
+	case _MALI_PRODUCT_ID_MALI200:
+		r = snprintf(buffer, 64, "Mali-200\n");
+		break;
+	case _MALI_PRODUCT_ID_MALI300:
+		r = snprintf(buffer, 64, "Mali-300\n");
+		break;
+	case _MALI_PRODUCT_ID_MALI400:
+		r = snprintf(buffer, 64, "Mali-400 MP\n");
+		break;
+	case _MALI_PRODUCT_ID_MALI450:
+		r = snprintf(buffer, 64, "Mali-450 MP\n");
+		break;
+	case _MALI_PRODUCT_ID_MALI470:
+		r = snprintf(buffer, 64, "Mali-470 MP\n");
+		break;
+	case _MALI_PRODUCT_ID_UNKNOWN:
+		return -EINVAL;
+		break;
+	};
+
+	return simple_read_from_buffer(buf, count, offp, buffer, r);
+}
+
+static const struct file_operations version_fops = {
+	.owner = THIS_MODULE,
+	.read = version_read,
+};
+
+#if defined(DEBUG)
+static int timeline_debugfs_show(struct seq_file *s, void *private_data)
+{
+	struct mali_session_data *session, *tmp;
+	u32 session_seq = 1;
+
+	seq_printf(s, "timeline system info: \n=================\n\n");
+
+	mali_session_lock();
+	MALI_SESSION_FOREACH(session, tmp, link) {
+		seq_printf(s, "session %d <%p> start:\n", session_seq, session);
+		mali_timeline_debug_print_system(session->timeline_system, s);
+		seq_printf(s, "session %d end\n\n\n", session_seq++);
+	}
+	mali_session_unlock();
+
+	return 0;
+}
+
+static int timeline_debugfs_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, timeline_debugfs_show, inode->i_private);
+}
+
+static const struct file_operations timeline_dump_fops = {
+	.owner = THIS_MODULE,
+	.open = timeline_debugfs_open,
+	.read  = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release
+};
+#endif
+
+int mali_sysfs_register(const char *mali_dev_name)
+{
+	mali_debugfs_dir = debugfs_create_dir(mali_dev_name, NULL);
+	if (ERR_PTR(-ENODEV) == mali_debugfs_dir) {
+		/* Debugfs not supported. */
+		mali_debugfs_dir = NULL;
+	} else {
+		if (NULL != mali_debugfs_dir) {
+			/* Debugfs directory created successfully; create files now */
+			struct dentry *mali_power_dir;
+			struct dentry *mali_gp_dir;
+			struct dentry *mali_pp_dir;
+			struct dentry *mali_l2_dir;
+			struct dentry *mali_profiling_dir;
+
+			debugfs_create_file("version", 0400, mali_debugfs_dir, NULL, &version_fops);
+
+			mali_power_dir = debugfs_create_dir("power", mali_debugfs_dir);
+			if (mali_power_dir != NULL) {
+				debugfs_create_file("always_on", 0600, mali_power_dir, NULL, &power_always_on_fops);
+				debugfs_create_file("power_events", 0200, mali_power_dir, NULL, &power_power_events_fops);
+			}
+
+			mali_gp_dir = debugfs_create_dir("gp", mali_debugfs_dir);
+			if (mali_gp_dir != NULL) {
+				u32 num_groups;
+				long i;
+
+				num_groups = mali_group_get_glob_num_groups();
+				for (i = 0; i < num_groups; i++) {
+					struct mali_group *group = mali_group_get_glob_group(i);
+
+					struct mali_gp_core *gp_core = mali_group_get_gp_core(group);
+					if (NULL != gp_core) {
+						struct dentry *mali_gp_gpx_dir;
+						mali_gp_gpx_dir = debugfs_create_dir("gp0", mali_gp_dir);
+						if (NULL != mali_gp_gpx_dir) {
+							debugfs_create_file("base_addr", 0400, mali_gp_gpx_dir, &gp_core->hw_core, &hw_core_base_addr_fops);
+							debugfs_create_file("enabled", 0600, mali_gp_gpx_dir, group, &group_enabled_fops);
+						}
+						break; /* no need to look for any other GP cores */
+					}
+
+				}
+			}
+
+			mali_pp_dir = debugfs_create_dir("pp", mali_debugfs_dir);
+			if (mali_pp_dir != NULL) {
+				u32 num_groups;
+				long i;
+
+				debugfs_create_file("num_cores_total", 0400, mali_pp_dir, NULL, &pp_num_cores_total_fops);
+				debugfs_create_file("num_cores_enabled", 0600, mali_pp_dir, NULL, &pp_num_cores_enabled_fops);
+				debugfs_create_file("core_scaling_enabled", 0600, mali_pp_dir, NULL, &pp_core_scaling_enabled_fops);
+
+				num_groups = mali_group_get_glob_num_groups();
+				for (i = 0; i < num_groups; i++) {
+					struct mali_group *group = mali_group_get_glob_group(i);
+
+					struct mali_pp_core *pp_core = mali_group_get_pp_core(group);
+					if (NULL != pp_core) {
+						char buf[16];
+						struct dentry *mali_pp_ppx_dir;
+						_mali_osk_snprintf(buf, sizeof(buf), "pp%u", mali_pp_core_get_id(pp_core));
+						mali_pp_ppx_dir = debugfs_create_dir(buf, mali_pp_dir);
+						if (NULL != mali_pp_ppx_dir) {
+							debugfs_create_file("base_addr", 0400, mali_pp_ppx_dir, &pp_core->hw_core, &hw_core_base_addr_fops);
+							if (!mali_group_is_virtual(group)) {
+								debugfs_create_file("enabled", 0600, mali_pp_ppx_dir, group, &group_enabled_fops);
+							}
+						}
+					}
+				}
+			}
+
+			mali_l2_dir = debugfs_create_dir("l2", mali_debugfs_dir);
+			if (mali_l2_dir != NULL) {
+				struct dentry *mali_l2_all_dir;
+				u32 l2_id;
+				struct mali_l2_cache_core *l2_cache;
+
+				mali_l2_all_dir = debugfs_create_dir("all", mali_l2_dir);
+				if (mali_l2_all_dir != NULL) {
+					debugfs_create_file("counter_src0", 0200, mali_l2_all_dir, NULL, &l2_all_counter_src0_fops);
+					debugfs_create_file("counter_src1", 0200, mali_l2_all_dir, NULL, &l2_all_counter_src1_fops);
+				}
+
+				l2_id = 0;
+				l2_cache = mali_l2_cache_core_get_glob_l2_core(l2_id);
+				while (NULL != l2_cache) {
+					char buf[16];
+					struct dentry *mali_l2_l2x_dir;
+					_mali_osk_snprintf(buf, sizeof(buf), "l2%u", l2_id);
+					mali_l2_l2x_dir = debugfs_create_dir(buf, mali_l2_dir);
+					if (NULL != mali_l2_l2x_dir) {
+						debugfs_create_file("counter_src0", 0600, mali_l2_l2x_dir, l2_cache, &l2_l2x_counter_src0_fops);
+						debugfs_create_file("counter_src1", 0600, mali_l2_l2x_dir, l2_cache, &l2_l2x_counter_src1_fops);
+						debugfs_create_file("counter_val0", 0600, mali_l2_l2x_dir, l2_cache, &l2_l2x_counter_val0_fops);
+						debugfs_create_file("counter_val1", 0600, mali_l2_l2x_dir, l2_cache, &l2_l2x_counter_val1_fops);
+						debugfs_create_file("base_addr", 0400, mali_l2_l2x_dir, &l2_cache->hw_core, &hw_core_base_addr_fops);
+					}
+
+					/* try next L2 */
+					l2_id++;
+					l2_cache = mali_l2_cache_core_get_glob_l2_core(l2_id);
+				}
+			}
+
+			debugfs_create_file("gpu_memory", 0444, mali_debugfs_dir, NULL, &memory_usage_fops);
+
+			debugfs_create_file("utilization_gp_pp", 0400, mali_debugfs_dir, NULL, &utilization_gp_pp_fops);
+			debugfs_create_file("utilization_gp", 0400, mali_debugfs_dir, NULL, &utilization_gp_fops);
+			debugfs_create_file("utilization_pp", 0400, mali_debugfs_dir, NULL, &utilization_pp_fops);
+
+			mali_profiling_dir = debugfs_create_dir("profiling", mali_debugfs_dir);
+			if (mali_profiling_dir != NULL) {
+				u32 max_sub_jobs;
+				long i;
+				struct dentry *mali_profiling_gp_dir;
+				struct dentry *mali_profiling_pp_dir;
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+				struct dentry *mali_profiling_proc_dir;
+#endif
+				/*
+				 * Create directory where we can set GP HW counters.
+				 */
+				mali_profiling_gp_dir = debugfs_create_dir("gp", mali_profiling_dir);
+				if (mali_profiling_gp_dir != NULL) {
+					debugfs_create_file("counter_src0", 0600, mali_profiling_gp_dir, (void *)PRIVATE_DATA_COUNTER_MAKE_GP(0), &profiling_counter_src_fops);
+					debugfs_create_file("counter_src1", 0600, mali_profiling_gp_dir, (void *)PRIVATE_DATA_COUNTER_MAKE_GP(1), &profiling_counter_src_fops);
+				}
+
+				/*
+				 * Create directory where we can set PP HW counters.
+				 * Possible override with specific HW counters for a particular sub job
+				 * (Disable core scaling before using the override!)
+				 */
+				mali_profiling_pp_dir = debugfs_create_dir("pp", mali_profiling_dir);
+				if (mali_profiling_pp_dir != NULL) {
+					debugfs_create_file("counter_src0", 0600, mali_profiling_pp_dir, (void *)PRIVATE_DATA_COUNTER_MAKE_PP(0), &profiling_counter_src_fops);
+					debugfs_create_file("counter_src1", 0600, mali_profiling_pp_dir, (void *)PRIVATE_DATA_COUNTER_MAKE_PP(1), &profiling_counter_src_fops);
+				}
+
+				max_sub_jobs = mali_executor_get_num_cores_total();
+				for (i = 0; i < max_sub_jobs; i++) {
+					char buf[16];
+					struct dentry *mali_profiling_pp_x_dir;
+					_mali_osk_snprintf(buf, sizeof(buf), "%u", i);
+					mali_profiling_pp_x_dir = debugfs_create_dir(buf, mali_profiling_pp_dir);
+					if (NULL != mali_profiling_pp_x_dir) {
+						debugfs_create_file("counter_src0",
+								    0600, mali_profiling_pp_x_dir,
+								    (void *)PRIVATE_DATA_COUNTER_MAKE_PP_SUB_JOB(0, i),
+								    &profiling_counter_src_fops);
+						debugfs_create_file("counter_src1",
+								    0600, mali_profiling_pp_x_dir,
+								    (void *)PRIVATE_DATA_COUNTER_MAKE_PP_SUB_JOB(1, i),
+								    &profiling_counter_src_fops);
+					}
+				}
+
+#if defined(CONFIG_MALI400_INTERNAL_PROFILING)
+				mali_profiling_proc_dir = debugfs_create_dir("proc", mali_profiling_dir);
+				if (mali_profiling_proc_dir != NULL) {
+					struct dentry *mali_profiling_proc_default_dir = debugfs_create_dir("default", mali_profiling_proc_dir);
+					if (mali_profiling_proc_default_dir != NULL) {
+						debugfs_create_file("enable", 0600, mali_profiling_proc_default_dir, (void *)_MALI_UK_USER_SETTING_SW_EVENTS_ENABLE, &user_settings_fops);
+					}
+				}
+				debugfs_create_file("record", 0600, mali_profiling_dir, NULL, &profiling_record_fops);
+				debugfs_create_file("events", 0400, mali_profiling_dir, NULL, &profiling_events_fops);
+				debugfs_create_file("events_human_readable", 0400, mali_profiling_dir, NULL, &profiling_events_human_readable_fops);
+#endif
+			}
+
+#if MALI_STATE_TRACKING
+			debugfs_create_file("state_dump", 0400, mali_debugfs_dir, NULL, &mali_seq_internal_state_fops);
+#endif
+
+#if defined(DEBUG)
+			debugfs_create_file("timeline_dump", 0400, mali_debugfs_dir, NULL, &timeline_dump_fops);
+#endif
+			if (mali_sysfs_user_settings_register()) {
+				/* Failed to create the debugfs entries for the user settings DB. */
+				MALI_DEBUG_PRINT(2, ("Failed to create user setting debugfs files. Ignoring...\n"));
+			}
+		}
+	}
+
+	/* Success! */
+	return 0;
+}
+
+int mali_sysfs_unregister(void)
+{
+	if (NULL != mali_debugfs_dir) {
+		debugfs_remove_recursive(mali_debugfs_dir);
+	}
+	return 0;
+}
+
+#else /* MALI_LICENSE_IS_GPL */
+
+/* Dummy implementations for non-GPL */
+
+int mali_sysfs_register(struct mali_dev *device, dev_t dev, const char *mali_dev_name)
+{
+	return 0;
+}
+
+int mali_sysfs_unregister(void)
+{
+	return 0;
+}
+
+#endif /* MALI_LICENSE_IS_GPL */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_kernel_sysfs.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_kernel_sysfs.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2011-2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_KERNEL_SYSFS_H__
+#define __MALI_KERNEL_SYSFS_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include <linux/device.h>
+
+#define MALI_PROC_DIR "driver/mali"
+
+int mali_sysfs_register(const char *mali_dev_name);
+int mali_sysfs_unregister(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_KERNEL_LINUX_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_linux_trace.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_linux_trace.h
@@ -0,0 +1,161 @@
+/*
+ * Copyright (C) 2012-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#if !defined (MALI_LINUX_TRACE_H) || defined (TRACE_HEADER_MULTI_READ)
+#define MALI_LINUX_TRACE_H
+
+#include <linux/types.h>
+
+#include <linux/tracepoint.h>
+
+#undef  TRACE_SYSTEM
+#define TRACE_SYSTEM mali
+#ifndef TRACEPOINTS_ENABLED
+#endif
+#define TRACE_INCLUDE_PATH .
+#define TRACE_INCLUDE_FILE mali_linux_trace
+
+/**
+ * Define the tracepoint used to communicate the status of a GPU. Called
+ * when a GPU turns on or turns off.
+ *
+ * @param event_id The type of the event. This parameter is a bitfield
+ *  encoding the type of the event.
+ *
+ * @param d0 First data parameter.
+ * @param d1 Second data parameter.
+ * @param d2 Third data parameter.
+ * @param d3 Fourth data parameter.
+ * @param d4 Fifth data parameter.
+ */
+TRACE_EVENT(mali_timeline_event,
+
+	    TP_PROTO(unsigned int event_id, unsigned int d0, unsigned int d1,
+		     unsigned int d2, unsigned int d3, unsigned int d4),
+
+	    TP_ARGS(event_id, d0, d1, d2, d3, d4),
+
+	    TP_STRUCT__entry(
+		    __field(unsigned int, event_id)
+		    __field(unsigned int, d0)
+		    __field(unsigned int, d1)
+		    __field(unsigned int, d2)
+		    __field(unsigned int, d3)
+		    __field(unsigned int, d4)
+	    ),
+
+	    TP_fast_assign(
+		    __entry->event_id = event_id;
+		    __entry->d0 = d0;
+		    __entry->d1 = d1;
+		    __entry->d2 = d2;
+		    __entry->d3 = d3;
+		    __entry->d4 = d4;
+	    ),
+
+	    TP_printk("event=%d", __entry->event_id)
+	   );
+
+/**
+ * Define a tracepoint used to regsiter the value of a hardware counter.
+ * Hardware counters belonging to the vertex or fragment processor are
+ * reported via this tracepoint each frame, whilst L2 cache hardware
+ * counters are reported continuously.
+ *
+ * @param counter_id The counter ID.
+ * @param value The value of the counter.
+ */
+TRACE_EVENT(mali_hw_counter,
+
+	    TP_PROTO(unsigned int counter_id, unsigned int value),
+
+	    TP_ARGS(counter_id, value),
+
+	    TP_STRUCT__entry(
+		    __field(unsigned int, counter_id)
+		    __field(unsigned int, value)
+	    ),
+
+	    TP_fast_assign(
+		    __entry->counter_id = counter_id;
+	    ),
+
+	    TP_printk("event %d = %d", __entry->counter_id, __entry->value)
+	   );
+
+/**
+ * Define a tracepoint used to send a bundle of software counters.
+ *
+ * @param counters The bundle of counters.
+ */
+TRACE_EVENT(mali_sw_counters,
+
+	    TP_PROTO(pid_t pid, pid_t tid, void *surface_id, unsigned int *counters),
+
+	    TP_ARGS(pid, tid, surface_id, counters),
+
+	    TP_STRUCT__entry(
+		    __field(pid_t, pid)
+		    __field(pid_t, tid)
+		    __field(void *, surface_id)
+		    __field(unsigned int *, counters)
+	    ),
+
+	    TP_fast_assign(
+		    __entry->pid = pid;
+		    __entry->tid = tid;
+		    __entry->surface_id = surface_id;
+		    __entry->counters = counters;
+	    ),
+
+	    TP_printk("counters were %s", __entry->counters == NULL ? "NULL" : "not NULL")
+	   );
+
+/**
+ * Define a tracepoint used to gather core activity for systrace
+ * @param pid The process id for which the core activity originates from
+ * @param active If the core is active (1) or not (0)
+ * @param core_type The type of core active, either GP (1) or PP (0)
+ * @param core_id The core id that is active for the core_type
+ * @param frame_builder_id The frame builder id associated with this core activity
+ * @param flush_id The flush id associated with this core activity
+ */
+TRACE_EVENT(mali_core_active,
+
+	    TP_PROTO(pid_t pid, unsigned int active, unsigned int core_type, unsigned int core_id, unsigned int frame_builder_id, unsigned int flush_id),
+
+	    TP_ARGS(pid, active, core_type, core_id, frame_builder_id, flush_id),
+
+	    TP_STRUCT__entry(
+		    __field(pid_t, pid)
+		    __field(unsigned int, active)
+		    __field(unsigned int, core_type)
+		    __field(unsigned int, core_id)
+		    __field(unsigned int, frame_builder_id)
+		    __field(unsigned int, flush_id)
+	    ),
+
+	    TP_fast_assign(
+		    __entry->pid = pid;
+		    __entry->active = active;
+		    __entry->core_type = core_type;
+		    __entry->core_id = core_id;
+		    __entry->frame_builder_id = frame_builder_id;
+		    __entry->flush_id = flush_id;
+	    ),
+
+	    TP_printk("%s|%d|%s%i:%x|%d", __entry->active ? "S" : "F", __entry->pid, __entry->core_type ? "GP" : "PP", __entry->core_id, __entry->flush_id, __entry->frame_builder_id)
+	   );
+
+#endif /* MALI_LINUX_TRACE_H */
+
+/* This part must exist outside the header guard. */
+#include <trace/define_trace.h>
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory.c
@@ -0,0 +1,587 @@
+/*
+ * Copyright (C) 2013-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/slab.h>
+#include <linux/version.h>
+#include <linux/platform_device.h>
+#include <linux/idr.h>
+
+#include "mali_osk.h"
+#include "mali_executor.h"
+
+#include "mali_memory.h"
+#include "mali_memory_os_alloc.h"
+#include "mali_memory_block_alloc.h"
+#include "mali_memory_util.h"
+#include "mali_memory_virtual.h"
+#include "mali_memory_manager.h"
+#include "mali_memory_cow.h"
+#include "mali_memory_swap_alloc.h"
+#include "mali_memory_defer_bind.h"
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+#include "mali_memory_secure.h"
+#endif
+
+extern unsigned int mali_dedicated_mem_size;
+extern unsigned int mali_shared_mem_size;
+
+#define MALI_VM_NUM_FAULT_PREFETCH (0x8)
+
+static void mali_mem_vma_open(struct vm_area_struct *vma)
+{
+	mali_mem_allocation *alloc = (mali_mem_allocation *)vma->vm_private_data;
+	MALI_DEBUG_PRINT(4, ("Open called on vma %p\n", vma));
+
+	/* If need to share the allocation, add ref_count here */
+	mali_allocation_ref(alloc);
+	return;
+}
+static void mali_mem_vma_close(struct vm_area_struct *vma)
+{
+	/* If need to share the allocation, unref ref_count here */
+	mali_mem_allocation *alloc = (mali_mem_allocation *)vma->vm_private_data;
+
+	if (NULL        != alloc) {
+		struct file *filp = NULL;
+		struct mali_session_data *session = NULL;
+
+		filp = vma->vm_file;
+		MALI_DEBUG_ASSERT(filp);
+		session = (struct mali_session_data *)filp->private_data;
+		MALI_DEBUG_ASSERT(session);
+
+		mali_session_memory_lock(session);
+		vma->vm_private_data = NULL;
+		mali_session_memory_unlock(session);
+
+		mali_allocation_unref(&alloc);
+	}
+}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 17, 0)
+static vm_fault_t  mali_mem_vma_fault(struct vm_fault *vmf)
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(4, 11, 0)
+static int mali_mem_vma_fault(struct vm_fault *vmf)
+#else
+static int mali_mem_vma_fault(struct vm_area_struct *vma, struct vm_fault *vmf)
+#endif
+{
+	struct file *filp = NULL;
+	struct mali_session_data *session = NULL;
+	mali_mem_allocation *alloc = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+	int ret;
+	int prefetch_num = MALI_VM_NUM_FAULT_PREFETCH;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 11, 0)
+	struct vm_area_struct *vma = vmf->vma;
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+	unsigned long address = (unsigned long)vmf->address;
+#else
+	unsigned long address = (unsigned long)vmf->virtual_address;
+#endif
+	filp = vma->vm_file;
+	MALI_DEBUG_ASSERT(filp);
+	session = (struct mali_session_data *)filp->private_data;
+	MALI_DEBUG_ASSERT(session);
+	mali_session_memory_lock(session);
+	if (NULL == vma->vm_private_data) {
+		MALI_DEBUG_PRINT(1, ("mali_vma_fault: The memory has been freed!\n"));
+		mali_session_memory_unlock(session);
+		return VM_FAULT_SIGBUS;
+	} else {
+		alloc = (mali_mem_allocation *)vma->vm_private_data;
+		MALI_DEBUG_ASSERT(alloc->backend_handle);
+		MALI_DEBUG_ASSERT(alloc->cpu_mapping.vma == vma);
+		MALI_DEBUG_ASSERT((unsigned long)alloc->cpu_mapping.addr <= address);
+		mali_allocation_ref(alloc);
+	}
+	mali_session_memory_unlock(session);
+
+
+	/* Get backend memory & Map on CPU */
+	mutex_lock(&mali_idr_mutex);
+	if (!(mem_bkend = idr_find(&mali_backend_idr, alloc->backend_handle))) {
+		MALI_DEBUG_PRINT(1, ("Can't find memory backend in mmap!\n"));
+		mutex_unlock(&mali_idr_mutex);
+		mali_allocation_unref(&alloc);
+		return VM_FAULT_SIGBUS;
+	}
+	mutex_unlock(&mali_idr_mutex);
+	MALI_DEBUG_ASSERT(mem_bkend->type == alloc->type);
+
+	if ((mem_bkend->type == MALI_MEM_COW && (MALI_MEM_BACKEND_FLAG_SWAP_COWED !=
+			(mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED))) &&
+	    (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_COW_CPU_NO_WRITE)) {
+		/*check if use page fault to do COW*/
+		MALI_DEBUG_PRINT(4, ("mali_vma_fault: do cow allocate on demand!, address=0x%x\n", address));
+		mutex_lock(&mem_bkend->mutex);
+		ret = mali_mem_cow_allocate_on_demand(mem_bkend,
+						      (address - vma->vm_start) / PAGE_SIZE);
+		mutex_unlock(&mem_bkend->mutex);
+
+		if (ret != _MALI_OSK_ERR_OK) {
+			mali_allocation_unref(&alloc);
+			return VM_FAULT_OOM;
+		}
+		prefetch_num = 1;
+
+		/* handle COW modified range cpu mapping
+		 we zap the mapping in cow_modify_range, it will trigger page fault
+		 when CPU access it, so here we map it to CPU*/
+		mutex_lock(&mem_bkend->mutex);
+		ret = mali_mem_cow_cpu_map_pages_locked(mem_bkend, vma, address, prefetch_num);
+		mutex_unlock(&mem_bkend->mutex);
+
+		if (unlikely(ret != _MALI_OSK_ERR_OK)) {
+			mali_allocation_unref(&alloc);
+			return VM_FAULT_SIGBUS;
+		}
+	} else if ((mem_bkend->type == MALI_MEM_SWAP) ||
+		   (mem_bkend->type == MALI_MEM_COW && (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED))) {
+		u32 offset_in_bkend = (address - vma->vm_start) / PAGE_SIZE;
+		int ret = _MALI_OSK_ERR_OK;
+
+		mutex_lock(&mem_bkend->mutex);
+		if (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_COW_CPU_NO_WRITE) {
+			ret = mali_mem_swap_cow_page_on_demand(mem_bkend, offset_in_bkend, &vmf->page);
+		} else {
+			ret = mali_mem_swap_allocate_page_on_demand(mem_bkend, offset_in_bkend, &vmf->page);
+		}
+		mutex_unlock(&mem_bkend->mutex);
+
+		if (ret != _MALI_OSK_ERR_OK) {
+			MALI_DEBUG_PRINT(2, ("Mali swap memory page fault process failed, address=0x%x\n", address));
+			mali_allocation_unref(&alloc);
+			return VM_FAULT_OOM;
+		} else {
+			mali_allocation_unref(&alloc);
+			return VM_FAULT_LOCKED;
+		}
+	} else {
+		MALI_PRINT_ERROR(("Mali vma fault! It never happen, indicating some logic errors in caller.\n"));
+		mali_allocation_unref(&alloc);
+		/*NOT support yet or OOM*/
+		return VM_FAULT_OOM;
+	}
+
+	mali_allocation_unref(&alloc);
+	return VM_FAULT_NOPAGE;
+}
+
+static struct vm_operations_struct mali_kernel_vm_ops = {
+	.open = mali_mem_vma_open,
+	.close = mali_mem_vma_close,
+	.fault = mali_mem_vma_fault,
+};
+
+
+/** @ map mali allocation to CPU address
+*
+* Supported backend types:
+* --MALI_MEM_OS
+* -- need to add COW?
+ *Not supported backend types:
+* -_MALI_MEMORY_BIND_BACKEND_UMP
+* -_MALI_MEMORY_BIND_BACKEND_DMA_BUF
+* -_MALI_MEMORY_BIND_BACKEND_EXTERNAL_MEMORY
+*
+*/
+int mali_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+	struct mali_session_data *session;
+	mali_mem_allocation *mali_alloc = NULL;
+	u32 mali_addr = vma->vm_pgoff << PAGE_SHIFT;
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+	int ret = -EFAULT;
+
+	session = (struct mali_session_data *)filp->private_data;
+	if (NULL == session) {
+		MALI_PRINT_ERROR(("mmap called without any session data available\n"));
+		return -EFAULT;
+	}
+
+	MALI_DEBUG_PRINT(4, ("MMap() handler: start=0x%08X, phys=0x%08X, size=0x%08X vma->flags 0x%08x\n",
+			     (unsigned int)vma->vm_start, (unsigned int)(vma->vm_pgoff << PAGE_SHIFT),
+			     (unsigned int)(vma->vm_end - vma->vm_start), vma->vm_flags));
+
+	/* Operations used on any memory system */
+	/* do not need to anything in vm open/close now */
+
+	/* find mali allocation structure by vaddress*/
+	mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_addr, 0);
+	if (likely(mali_vma_node)) {
+		mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+		MALI_DEBUG_ASSERT(mali_addr == mali_vma_node->vm_node.start);
+		if (unlikely(mali_addr != mali_vma_node->vm_node.start)) {
+			/* only allow to use start address for mmap */
+			MALI_DEBUG_PRINT(1, ("mali_addr != mali_vma_node->vm_node.start\n"));
+			return -EFAULT;
+		}
+	} else {
+		MALI_DEBUG_ASSERT(NULL == mali_vma_node);
+		return -EFAULT;
+	}
+
+	mali_alloc->cpu_mapping.addr = (void __user *)vma->vm_start;
+
+	if (mali_alloc->flags & _MALI_MEMORY_ALLOCATE_DEFER_BIND) {
+		MALI_DEBUG_PRINT(1, ("ERROR : trying to access varying memory by CPU!\n"));
+		return -EFAULT;
+	}
+
+	/* Get backend memory & Map on CPU */
+	mutex_lock(&mali_idr_mutex);
+	if (!(mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle))) {
+		MALI_DEBUG_PRINT(1, ("Can't find memory backend in mmap!\n"));
+		mutex_unlock(&mali_idr_mutex);
+		return -EFAULT;
+	}
+	mutex_unlock(&mali_idr_mutex);
+
+	if ((vma->vm_start + mem_bkend->size) > vma->vm_end) {
+		MALI_PRINT_ERROR(("mali_mmap: out of memory mapping map_size %d, physical_size %d\n",  vma->vm_end - vma->vm_start, mem_bkend->size));
+		return -EFAULT;
+	}
+
+	if (!(MALI_MEM_SWAP == mali_alloc->type ||
+	      (MALI_MEM_COW == mali_alloc->type && (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED)))) {
+		/* Set some bits which indicate that, the memory is IO memory, meaning
+		 * that no paging is to be performed and the memory should not be
+		 * included in crash dumps. And that the memory is reserved, meaning
+		 * that it's present and can never be paged out (see also previous
+		 * entry)
+		 */
+		vma->vm_flags |= VM_IO;
+		vma->vm_flags |= VM_DONTCOPY;
+		vma->vm_flags |= VM_PFNMAP;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 7, 0)
+		vma->vm_flags |= VM_RESERVED;
+#else
+		vma->vm_flags |= VM_DONTDUMP;
+		vma->vm_flags |= VM_DONTEXPAND;
+#endif
+	} else if (MALI_MEM_SWAP == mali_alloc->type) {
+		vma->vm_pgoff = mem_bkend->start_idx;
+	}
+
+	vma->vm_page_prot = pgprot_writecombine(vma->vm_page_prot);
+	vma->vm_ops = &mali_kernel_vm_ops;
+
+	mali_alloc->cpu_mapping.addr = (void __user *)vma->vm_start;
+
+	/* If it's a copy-on-write mapping, map to read only */
+	if (!(vma->vm_flags & VM_WRITE)) {
+		MALI_DEBUG_PRINT(4, ("mmap allocation with read only !\n"));
+		/* add VM_WRITE for do_page_fault will check this when a write fault */
+		vma->vm_flags |= VM_WRITE | VM_READ;
+		vma->vm_page_prot = PAGE_READONLY;
+		vma->vm_page_prot = pgprot_writecombine(vma->vm_page_prot);
+		mem_bkend->flags |= MALI_MEM_BACKEND_FLAG_COW_CPU_NO_WRITE;
+		goto out;
+	}
+
+	if (mem_bkend->type == MALI_MEM_OS) {
+		ret = mali_mem_os_cpu_map(mem_bkend, vma);
+	} else if (mem_bkend->type == MALI_MEM_COW &&
+		   (MALI_MEM_BACKEND_FLAG_SWAP_COWED != (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED))) {
+		ret = mali_mem_cow_cpu_map(mem_bkend, vma);
+	} else if (mem_bkend->type == MALI_MEM_BLOCK) {
+		ret = mali_mem_block_cpu_map(mem_bkend, vma);
+	} else if ((mem_bkend->type == MALI_MEM_SWAP) || (mem_bkend->type == MALI_MEM_COW &&
+			(MALI_MEM_BACKEND_FLAG_SWAP_COWED == (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED)))) {
+		/*For swappable memory, CPU page table will be created by page fault handler. */
+		ret = 0;
+	} else if (mem_bkend->type == MALI_MEM_SECURE) {
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+		ret = mali_mem_secure_cpu_map(mem_bkend, vma);
+#else
+		MALI_DEBUG_PRINT(1, ("DMA not supported for mali secure memory\n"));
+		return -EFAULT;
+#endif
+	} else {
+		/* Not support yet*/
+		MALI_DEBUG_PRINT_ERROR(("Invalid type of backend memory! \n"));
+		return -EFAULT;
+	}
+
+	if (ret != 0) {
+		MALI_DEBUG_PRINT(1, ("ret != 0\n"));
+		return -EFAULT;
+	}
+out:
+	MALI_DEBUG_ASSERT(MALI_MEM_ALLOCATION_VALID_MAGIC == mali_alloc->magic);
+
+	vma->vm_private_data = (void *)mali_alloc;
+	mali_alloc->cpu_mapping.vma = vma;
+
+	mali_allocation_ref(mali_alloc);
+
+	return 0;
+}
+
+_mali_osk_errcode_t mali_mem_mali_map_prepare(mali_mem_allocation *descriptor)
+{
+	u32 size = descriptor->psize;
+	struct mali_session_data *session = descriptor->session;
+
+	MALI_DEBUG_ASSERT(MALI_MEM_ALLOCATION_VALID_MAGIC == descriptor->magic);
+
+	/* Map dma-buf into this session's page tables */
+
+	if (descriptor->flags & MALI_MEM_FLAG_MALI_GUARD_PAGE) {
+		size += MALI_MMU_PAGE_SIZE;
+	}
+
+	return mali_mmu_pagedir_map(session->page_directory, descriptor->mali_vma_node.vm_node.start, size);
+}
+
+_mali_osk_errcode_t mali_mem_mali_map_resize(mali_mem_allocation *descriptor, u32 new_size)
+{
+	u32 old_size = descriptor->psize;
+	struct mali_session_data *session = descriptor->session;
+
+	MALI_DEBUG_ASSERT(MALI_MEM_ALLOCATION_VALID_MAGIC == descriptor->magic);
+
+	if (descriptor->flags & MALI_MEM_FLAG_MALI_GUARD_PAGE) {
+		new_size  += MALI_MMU_PAGE_SIZE;
+	}
+
+	if (new_size > old_size) {
+		MALI_DEBUG_ASSERT(new_size <= descriptor->mali_vma_node.vm_node.size);
+		return mali_mmu_pagedir_map(session->page_directory, descriptor->mali_vma_node.vm_node.start + old_size, new_size - old_size);
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mem_mali_map_free(struct mali_session_data *session, u32 size, mali_address_t vaddr, u32 flags)
+{
+	if (flags & MALI_MEM_FLAG_MALI_GUARD_PAGE) {
+		size += MALI_MMU_PAGE_SIZE;
+	}
+
+	/* Umap and flush L2 */
+	mali_mmu_pagedir_unmap(session->page_directory, vaddr, size);
+	mali_executor_zap_all_active(session);
+}
+
+u32 _mali_ukk_report_memory_usage(void)
+{
+	u32 sum = 0;
+
+	if (MALI_TRUE == mali_memory_have_dedicated_memory()) {
+		sum += mali_mem_block_allocator_stat();
+	}
+
+	sum += mali_mem_os_stat();
+
+	return sum;
+}
+
+u32 _mali_ukk_report_total_memory_size(void)
+{
+	return mali_dedicated_mem_size + mali_shared_mem_size;
+}
+
+
+/**
+ * Per-session memory descriptor mapping table sizes
+ */
+#define MALI_MEM_DESCRIPTORS_INIT 64
+#define MALI_MEM_DESCRIPTORS_MAX 65536
+
+_mali_osk_errcode_t mali_memory_session_begin(struct mali_session_data *session_data)
+{
+	MALI_DEBUG_PRINT(5, ("Memory session begin\n"));
+
+	session_data->memory_lock = _mali_osk_mutex_init(_MALI_OSK_LOCKFLAG_ORDERED,
+				    _MALI_OSK_LOCK_ORDER_MEM_SESSION);
+
+	if (NULL == session_data->memory_lock) {
+		MALI_ERROR(_MALI_OSK_ERR_FAULT);
+	}
+
+	session_data->cow_lock = _mali_osk_mutex_init(_MALI_OSK_LOCKFLAG_UNORDERED, 0);
+	if (NULL == session_data->cow_lock) {
+		_mali_osk_mutex_term(session_data->memory_lock);
+		MALI_ERROR(_MALI_OSK_ERR_FAULT);
+	}
+
+	mali_memory_manager_init(&session_data->allocation_mgr);
+
+	MALI_DEBUG_PRINT(5, ("MMU session begin: success\n"));
+	MALI_SUCCESS;
+}
+
+void mali_memory_session_end(struct mali_session_data *session)
+{
+	MALI_DEBUG_PRINT(3, ("MMU session end\n"));
+
+	if (NULL == session) {
+		MALI_DEBUG_PRINT(1, ("No session data found during session end\n"));
+		return;
+	}
+	/* free allocation */
+	mali_free_session_allocations(session);
+	/* do some check in unint*/
+	mali_memory_manager_uninit(&session->allocation_mgr);
+
+	/* Free the lock */
+	_mali_osk_mutex_term(session->memory_lock);
+	_mali_osk_mutex_term(session->cow_lock);
+	return;
+}
+
+_mali_osk_errcode_t mali_memory_initialize(void)
+{
+	_mali_osk_errcode_t err;
+
+	idr_init(&mali_backend_idr);
+	mutex_init(&mali_idr_mutex);
+
+	err = mali_mem_swap_init();
+	if (err != _MALI_OSK_ERR_OK) {
+		return err;
+	}
+	err = mali_mem_os_init();
+	if (_MALI_OSK_ERR_OK == err) {
+		err = mali_mem_defer_bind_manager_init();
+	}
+
+	return err;
+}
+
+void mali_memory_terminate(void)
+{
+	mali_mem_swap_term();
+	mali_mem_defer_bind_manager_destory();
+	mali_mem_os_term();
+	if (mali_memory_have_dedicated_memory()) {
+		mali_mem_block_allocator_destroy();
+	}
+}
+
+
+struct mali_page_node *_mali_page_node_allocate(mali_page_node_type type)
+{
+	mali_page_node *page_node = NULL;
+
+	page_node = kzalloc(sizeof(mali_page_node), GFP_KERNEL);
+	MALI_DEBUG_ASSERT(NULL != page_node);
+
+	if (page_node) {
+		page_node->type = type;
+		INIT_LIST_HEAD(&page_node->list);
+	}
+
+	return page_node;
+}
+
+void _mali_page_node_ref(struct mali_page_node *node)
+{
+	if (node->type == MALI_PAGE_NODE_OS) {
+		/* add ref to this page */
+		get_page(node->page);
+	} else if (node->type == MALI_PAGE_NODE_BLOCK) {
+		mali_mem_block_add_ref(node);
+	} else if (node->type == MALI_PAGE_NODE_SWAP) {
+		atomic_inc(&node->swap_it->ref_count);
+	} else {
+		MALI_DEBUG_PRINT_ERROR(("Invalid type of mali page node! \n"));
+	}
+}
+
+void _mali_page_node_unref(struct mali_page_node *node)
+{
+	if (node->type == MALI_PAGE_NODE_OS) {
+		/* unref to this page */
+		put_page(node->page);
+	} else if (node->type == MALI_PAGE_NODE_BLOCK) {
+		mali_mem_block_dec_ref(node);
+	} else {
+		MALI_DEBUG_PRINT_ERROR(("Invalid type of mali page node! \n"));
+	}
+}
+
+
+void _mali_page_node_add_page(struct mali_page_node *node, struct page *page)
+{
+	MALI_DEBUG_ASSERT(MALI_PAGE_NODE_OS == node->type);
+	node->page = page;
+}
+
+
+void _mali_page_node_add_swap_item(struct mali_page_node *node, struct mali_swap_item *item)
+{
+	MALI_DEBUG_ASSERT(MALI_PAGE_NODE_SWAP == node->type);
+	node->swap_it = item;
+}
+
+void _mali_page_node_add_block_item(struct mali_page_node *node, mali_block_item *item)
+{
+	MALI_DEBUG_ASSERT(MALI_PAGE_NODE_BLOCK == node->type);
+	node->blk_it = item;
+}
+
+
+int _mali_page_node_get_ref_count(struct mali_page_node *node)
+{
+	if (node->type == MALI_PAGE_NODE_OS) {
+		/* get ref count of this page */
+		return page_count(node->page);
+	} else if (node->type == MALI_PAGE_NODE_BLOCK) {
+		return mali_mem_block_get_ref_count(node);
+	} else if (node->type == MALI_PAGE_NODE_SWAP) {
+		return atomic_read(&node->swap_it->ref_count);
+	} else {
+		MALI_DEBUG_PRINT_ERROR(("Invalid type of mali page node! \n"));
+	}
+	return -1;
+}
+
+
+dma_addr_t _mali_page_node_get_dma_addr(struct mali_page_node *node)
+{
+	if (node->type == MALI_PAGE_NODE_OS) {
+		return page_private(node->page);
+	} else if (node->type == MALI_PAGE_NODE_BLOCK) {
+		return _mali_blk_item_get_phy_addr(node->blk_it);
+	} else if (node->type == MALI_PAGE_NODE_SWAP) {
+		return node->swap_it->dma_addr;
+	} else {
+		MALI_DEBUG_PRINT_ERROR(("Invalid type of mali page node! \n"));
+	}
+	return 0;
+}
+
+
+unsigned long _mali_page_node_get_pfn(struct mali_page_node *node)
+{
+	if (node->type == MALI_PAGE_NODE_OS) {
+		return page_to_pfn(node->page);
+	} else if (node->type == MALI_PAGE_NODE_BLOCK) {
+		/* get phy addr for BLOCK page*/
+		return _mali_blk_item_get_pfn(node->blk_it);
+	} else if (node->type == MALI_PAGE_NODE_SWAP) {
+		return page_to_pfn(node->swap_it->page);
+	} else {
+		MALI_DEBUG_PRINT_ERROR(("Invalid type of mali page node! \n"));
+	}
+	return 0;
+}
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory.h
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_H__
+#define __MALI_MEMORY_H__
+
+#include "mali_osk.h"
+#include "mali_session.h"
+
+#include <linux/list.h>
+#include <linux/mm.h>
+
+#include "mali_memory_types.h"
+#include "mali_memory_os_alloc.h"
+
+_mali_osk_errcode_t mali_memory_initialize(void);
+void mali_memory_terminate(void);
+
+/** @brief Allocate a page table page
+ *
+ * Allocate a page for use as a page directory or page table. The page is
+ * mapped into kernel space.
+ *
+ * @return _MALI_OSK_ERR_OK on success, otherwise an error code
+ * @param table_page GPU pointer to the allocated page
+ * @param mapping CPU pointer to the mapping of the allocated page
+ */
+MALI_STATIC_INLINE _mali_osk_errcode_t
+mali_mmu_get_table_page(mali_dma_addr *table_page, mali_io_address *mapping)
+{
+	return mali_mem_os_get_table_page(table_page, mapping);
+}
+
+/** @brief Release a page table page
+ *
+ * Release a page table page allocated through \a mali_mmu_get_table_page
+ *
+ * @param pa the GPU address of the page to release
+ */
+MALI_STATIC_INLINE void
+mali_mmu_release_table_page(mali_dma_addr phys, void *virt)
+{
+	mali_mem_os_release_table_page(phys, virt);
+}
+
+/** @brief mmap function
+ *
+ * mmap syscalls on the Mali device node will end up here.
+ *
+ * This function allocates Mali memory and maps it on CPU and Mali.
+ */
+int mali_mmap(struct file *filp, struct vm_area_struct *vma);
+
+/** @brief Start a new memory session
+ *
+ * Called when a process opens the Mali device node.
+ *
+ * @param session Pointer to session to initialize
+ */
+_mali_osk_errcode_t mali_memory_session_begin(struct mali_session_data *session);
+
+/** @brief Close a memory session
+ *
+ * Called when a process closes the Mali device node.
+ *
+ * Memory allocated by the session will be freed
+ *
+ * @param session Pointer to the session to terminate
+ */
+void mali_memory_session_end(struct mali_session_data *session);
+
+/** @brief Prepare Mali page tables for mapping
+ *
+ * This function will prepare the Mali page tables for mapping the memory
+ * described by \a descriptor.
+ *
+ * Page tables will be reference counted and allocated, if not yet present.
+ *
+ * @param descriptor Pointer to the memory descriptor to the mapping
+ */
+_mali_osk_errcode_t mali_mem_mali_map_prepare(mali_mem_allocation *descriptor);
+
+/** @brief Resize Mali page tables for mapping
+ *
+ * This function will Resize the Mali page tables for mapping the memory
+ * described by \a descriptor.
+ *
+ * Page tables will be reference counted and allocated, if not yet present.
+ *
+ * @param descriptor Pointer to the memory descriptor to the mapping
+ * @param new_size The new size of descriptor
+ */
+_mali_osk_errcode_t mali_mem_mali_map_resize(mali_mem_allocation *descriptor, u32 new_size);
+
+/** @brief Free Mali page tables for mapping
+ *
+ * This function will unmap pages from Mali memory and free the page tables
+ * that are now unused.
+ *
+ * The updated pages in the Mali L2 cache will be invalidated, and the MMU TLBs will be zapped if necessary.
+ *
+ * @param descriptor Pointer to the memory descriptor to unmap
+ */
+void mali_mem_mali_map_free(struct mali_session_data *session, u32 size, mali_address_t vaddr, u32 flags);
+
+/** @brief Parse resource and prepare the OS memory allocator
+ *
+ * @param size Maximum size to allocate for Mali GPU.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t mali_memory_core_resource_os_memory(u32 size);
+
+/** @brief Parse resource and prepare the dedicated memory allocator
+ *
+ * @param start Physical start address of dedicated Mali GPU memory.
+ * @param size Size of dedicated Mali GPU memory.
+ * @return _MALI_OSK_ERR_OK on success, otherwise failure.
+ */
+_mali_osk_errcode_t mali_memory_core_resource_dedicated_memory(u32 start, u32 size);
+
+
+struct mali_page_node *_mali_page_node_allocate(mali_page_node_type type);
+
+void _mali_page_node_ref(struct mali_page_node *node);
+void _mali_page_node_unref(struct mali_page_node *node);
+void _mali_page_node_add_page(struct mali_page_node *node, struct page *page);
+
+void _mali_page_node_add_block_item(struct mali_page_node *node, mali_block_item *item);
+
+void _mali_page_node_add_swap_item(struct mali_page_node *node, struct mali_swap_item *item);
+
+int _mali_page_node_get_ref_count(struct mali_page_node *node);
+dma_addr_t _mali_page_node_get_dma_addr(struct mali_page_node *node);
+unsigned long _mali_page_node_get_pfn(struct mali_page_node *node);
+
+#endif /* __MALI_MEMORY_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_block_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_block_alloc.c
@@ -0,0 +1,366 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_memory.h"
+#include "mali_memory_block_alloc.h"
+#include "mali_osk.h"
+#include <linux/mutex.h>
+
+
+static mali_block_allocator *mali_mem_block_gobal_allocator = NULL;
+
+unsigned long _mali_blk_item_get_phy_addr(mali_block_item *item)
+{
+	return (item->phy_addr & ~(MALI_BLOCK_REF_MASK));
+}
+
+
+unsigned long _mali_blk_item_get_pfn(mali_block_item *item)
+{
+	return (item->phy_addr / MALI_BLOCK_SIZE);
+}
+
+
+u32 mali_mem_block_get_ref_count(mali_page_node *node)
+{
+	MALI_DEBUG_ASSERT(node->type == MALI_PAGE_NODE_BLOCK);
+	return (node->blk_it->phy_addr & MALI_BLOCK_REF_MASK);
+}
+
+
+/* Increase the refence count
+* It not atomic, so it need to get sp_lock before call this function
+*/
+
+u32 mali_mem_block_add_ref(mali_page_node *node)
+{
+	MALI_DEBUG_ASSERT(node->type == MALI_PAGE_NODE_BLOCK);
+	MALI_DEBUG_ASSERT(mali_mem_block_get_ref_count(node) < MALI_BLOCK_MAX_REF_COUNT);
+	return (node->blk_it->phy_addr++ & MALI_BLOCK_REF_MASK);
+}
+
+/* Decase the refence count
+* It not atomic, so it need to get sp_lock before call this function
+*/
+u32 mali_mem_block_dec_ref(mali_page_node *node)
+{
+	MALI_DEBUG_ASSERT(node->type == MALI_PAGE_NODE_BLOCK);
+	MALI_DEBUG_ASSERT(mali_mem_block_get_ref_count(node) > 0);
+	return (node->blk_it->phy_addr-- & MALI_BLOCK_REF_MASK);
+}
+
+
+static mali_block_allocator *mali_mem_block_allocator_create(u32 base_address, u32 size)
+{
+	mali_block_allocator *info;
+	u32 usable_size;
+	u32 num_blocks;
+	mali_page_node *m_node;
+	mali_block_item *mali_blk_items = NULL;
+	int i = 0;
+
+	usable_size = size & ~(MALI_BLOCK_SIZE - 1);
+	MALI_DEBUG_PRINT(3, ("Mali block allocator create for region starting at 0x%08X length 0x%08X\n", base_address, size));
+	MALI_DEBUG_PRINT(4, ("%d usable bytes\n", usable_size));
+	num_blocks = usable_size / MALI_BLOCK_SIZE;
+	MALI_DEBUG_PRINT(4, ("which becomes %d blocks\n", num_blocks));
+
+	if (usable_size == 0) {
+		MALI_DEBUG_PRINT(1, ("Memory block of size %d is unusable\n", size));
+		return NULL;
+	}
+
+	info = _mali_osk_calloc(1, sizeof(mali_block_allocator));
+	if (NULL != info) {
+		INIT_LIST_HEAD(&info->free);
+		spin_lock_init(&info->sp_lock);
+		info->total_num = num_blocks;
+		mali_blk_items = _mali_osk_calloc(1, sizeof(mali_block_item) * num_blocks);
+
+		if (mali_blk_items) {
+			info->items = mali_blk_items;
+			/* add blocks(4k size) to free list*/
+			for (i = 0 ; i < num_blocks ; i++) {
+				/* add block information*/
+				mali_blk_items[i].phy_addr = base_address + (i * MALI_BLOCK_SIZE);
+				/* add  to free list */
+				m_node = _mali_page_node_allocate(MALI_PAGE_NODE_BLOCK);
+				if (m_node == NULL)
+					goto fail;
+				_mali_page_node_add_block_item(m_node, &(mali_blk_items[i]));
+				list_add_tail(&m_node->list, &info->free);
+				atomic_add(1, &info->free_num);
+			}
+			return info;
+		}
+	}
+fail:
+	mali_mem_block_allocator_destroy();
+	return NULL;
+}
+
+void mali_mem_block_allocator_destroy(void)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	mali_block_allocator *info = mali_mem_block_gobal_allocator;
+	MALI_DEBUG_ASSERT_POINTER(info);
+	MALI_DEBUG_PRINT(4, ("Memory block destroy !\n"));
+
+	if (NULL == info)
+		return;
+
+	list_for_each_entry_safe(m_page, m_tmp , &info->free, list) {
+		MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_BLOCK);
+		list_del(&m_page->list);
+		kfree(m_page);
+	}
+
+	_mali_osk_free(info->items);
+	_mali_osk_free(info);
+}
+
+u32 mali_mem_block_release(mali_mem_backend *mem_bkend)
+{
+	mali_mem_allocation *alloc = mem_bkend->mali_allocation;
+	u32 free_pages_nr = 0;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_BLOCK);
+
+	/* Unmap the memory from the mali virtual address space. */
+	mali_mem_block_mali_unmap(alloc);
+	mutex_lock(&mem_bkend->mutex);
+	free_pages_nr = mali_mem_block_free(&mem_bkend->block_mem);
+	mutex_unlock(&mem_bkend->mutex);
+	return free_pages_nr;
+}
+
+
+int mali_mem_block_alloc(mali_mem_block_mem *block_mem, u32 size)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	size_t page_count = PAGE_ALIGN(size) / _MALI_OSK_MALI_PAGE_SIZE;
+	mali_block_allocator *info = mali_mem_block_gobal_allocator;
+	MALI_DEBUG_ASSERT_POINTER(info);
+
+	MALI_DEBUG_PRINT(4, ("BLOCK Mem: Allocate size = 0x%x\n", size));
+	/*do some init */
+	INIT_LIST_HEAD(&block_mem->pfns);
+
+	spin_lock(&info->sp_lock);
+	/*check if have enough space*/
+	if (atomic_read(&info->free_num) > page_count) {
+		list_for_each_entry_safe(m_page, m_tmp , &info->free, list) {
+			if (page_count > 0) {
+				MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_BLOCK);
+				MALI_DEBUG_ASSERT(mali_mem_block_get_ref_count(m_page) == 0);
+				list_move(&m_page->list, &block_mem->pfns);
+				block_mem->count++;
+				atomic_dec(&info->free_num);
+				_mali_page_node_ref(m_page);
+			} else {
+				break;
+			}
+			page_count--;
+		}
+	} else {
+		/* can't allocate from BLOCK memory*/
+		spin_unlock(&info->sp_lock);
+		return -1;
+	}
+
+	spin_unlock(&info->sp_lock);
+	return 0;
+}
+
+u32 mali_mem_block_free(mali_mem_block_mem *block_mem)
+{
+	u32 free_pages_nr = 0;
+
+	free_pages_nr = mali_mem_block_free_list(&block_mem->pfns);
+	MALI_DEBUG_PRINT(4, ("BLOCK Mem free : allocated size = 0x%x, free size = 0x%x\n", block_mem->count * _MALI_OSK_MALI_PAGE_SIZE,
+			     free_pages_nr * _MALI_OSK_MALI_PAGE_SIZE));
+	block_mem->count = 0;
+	MALI_DEBUG_ASSERT(list_empty(&block_mem->pfns));
+
+	return free_pages_nr;
+}
+
+
+u32 mali_mem_block_free_list(struct list_head *list)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	mali_block_allocator *info = mali_mem_block_gobal_allocator;
+	u32 free_pages_nr = 0;
+
+	if (info) {
+		spin_lock(&info->sp_lock);
+		list_for_each_entry_safe(m_page, m_tmp , list, list) {
+			if (1 == _mali_page_node_get_ref_count(m_page)) {
+				free_pages_nr++;
+			}
+			mali_mem_block_free_node(m_page);
+		}
+		spin_unlock(&info->sp_lock);
+	}
+	return free_pages_nr;
+}
+
+/* free the node,*/
+void mali_mem_block_free_node(struct mali_page_node *node)
+{
+	mali_block_allocator *info = mali_mem_block_gobal_allocator;
+
+	/* only handle BLOCK node */
+	if (node->type == MALI_PAGE_NODE_BLOCK && info) {
+		/*Need to make this atomic?*/
+		if (1 == _mali_page_node_get_ref_count(node)) {
+			/*Move to free list*/
+			_mali_page_node_unref(node);
+			list_move_tail(&node->list, &info->free);
+			atomic_add(1, &info->free_num);
+		} else {
+			_mali_page_node_unref(node);
+			list_del(&node->list);
+			kfree(node);
+		}
+	}
+}
+
+/* unref the node, but not free it */
+_mali_osk_errcode_t mali_mem_block_unref_node(struct mali_page_node *node)
+{
+	mali_block_allocator *info = mali_mem_block_gobal_allocator;
+	mali_page_node *new_node;
+
+	/* only handle BLOCK node */
+	if (node->type == MALI_PAGE_NODE_BLOCK && info) {
+		/*Need to make this atomic?*/
+		if (1 == _mali_page_node_get_ref_count(node)) {
+			/* allocate a  new node, Add to free list, keep the old node*/
+			_mali_page_node_unref(node);
+			new_node = _mali_page_node_allocate(MALI_PAGE_NODE_BLOCK);
+			if (new_node) {
+				memcpy(new_node, node, sizeof(mali_page_node));
+				list_add(&new_node->list, &info->free);
+				atomic_add(1, &info->free_num);
+			} else
+				return _MALI_OSK_ERR_FAULT;
+
+		} else {
+			_mali_page_node_unref(node);
+		}
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+
+int mali_mem_block_mali_map(mali_mem_block_mem *block_mem, struct mali_session_data *session, u32 vaddr, u32 props)
+{
+	struct mali_page_directory *pagedir = session->page_directory;
+	struct mali_page_node *m_page;
+	dma_addr_t phys;
+	u32 virt = vaddr;
+	u32 prop = props;
+
+	list_for_each_entry(m_page, &block_mem->pfns, list) {
+		MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_BLOCK);
+		phys = _mali_page_node_get_dma_addr(m_page);
+#if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT)
+		/* Verify that the "physical" address is 32-bit and
+		 * usable for Mali, when on a system with bus addresses
+		 * wider than 32-bit. */
+		MALI_DEBUG_ASSERT(0 == (phys >> 32));
+#endif
+		mali_mmu_pagedir_update(pagedir, virt, (mali_dma_addr)phys, MALI_MMU_PAGE_SIZE, prop);
+		virt += MALI_MMU_PAGE_SIZE;
+	}
+
+	return 0;
+}
+
+void mali_mem_block_mali_unmap(mali_mem_allocation *alloc)
+{
+	struct mali_session_data *session;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	mali_session_memory_lock(session);
+	mali_mem_mali_map_free(session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+			       alloc->flags);
+	mali_session_memory_unlock(session);
+}
+
+
+int mali_mem_block_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma)
+{
+	int ret;
+	mali_mem_block_mem *block_mem = &mem_bkend->block_mem;
+	unsigned long addr = vma->vm_start;
+	struct mali_page_node *m_page;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_BLOCK);
+
+	list_for_each_entry(m_page, &block_mem->pfns, list) {
+		MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_BLOCK);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+		ret = vmf_insert_pfn(vma, addr, _mali_page_node_get_pfn(m_page));
+		if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+		ret = vm_insert_pfn(vma, addr, _mali_page_node_get_pfn(m_page));
+		if (unlikely(0 != ret)) {
+#endif
+			return -EFAULT;
+		}
+		addr += _MALI_OSK_MALI_PAGE_SIZE;
+
+	}
+
+	return 0;
+}
+
+
+_mali_osk_errcode_t mali_memory_core_resource_dedicated_memory(u32 start, u32 size)
+{
+	mali_block_allocator *allocator;
+
+	/* Do the low level linux operation first */
+
+	/* Request ownership of the memory */
+	if (_MALI_OSK_ERR_OK != _mali_osk_mem_reqregion(start, size, "Dedicated Mali GPU memory")) {
+		MALI_DEBUG_PRINT(1, ("Failed to request memory region for frame buffer (0x%08X - 0x%08X)\n", start, start + size - 1));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Create generic block allocator object to handle it */
+	allocator = mali_mem_block_allocator_create(start, size);
+
+	if (NULL == allocator) {
+		MALI_DEBUG_PRINT(1, ("Memory bank registration failed\n"));
+		_mali_osk_mem_unreqregion(start, size);
+		MALI_ERROR(_MALI_OSK_ERR_FAULT);
+	}
+
+	mali_mem_block_gobal_allocator = (mali_block_allocator *)allocator;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+mali_bool mali_memory_have_dedicated_memory(void)
+{
+	return mali_mem_block_gobal_allocator ? MALI_TRUE : MALI_FALSE;
+}
+
+u32 mali_mem_block_allocator_stat(void)
+{
+	mali_block_allocator *allocator = mali_mem_block_gobal_allocator;
+	MALI_DEBUG_ASSERT_POINTER(allocator);
+
+	return (allocator->total_num - atomic_read(&allocator->free_num)) * _MALI_OSK_MALI_PAGE_SIZE;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_block_alloc.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_block_alloc.h
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2010, 2013, 2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_BLOCK_ALLOCATOR_H__
+#define __MALI_BLOCK_ALLOCATOR_H__
+
+#include "mali_session.h"
+#include "mali_memory.h"
+#include <linux/spinlock.h>
+
+#include "mali_memory_types.h"
+
+#define MALI_BLOCK_SIZE (PAGE_SIZE)  /* 4 kB, manage BLOCK memory as page size */
+#define MALI_BLOCK_REF_MASK (0xFFF)
+#define MALI_BLOCK_MAX_REF_COUNT (0xFFF)
+
+
+
+typedef struct mali_block_allocator {
+	/*
+	* In free list, each node's ref_count is 0,
+	* ref_count added when allocated or referenced in COW
+	*/
+	mali_block_item *items; /* information for each block item*/
+	struct list_head free; /*free list of mali_memory_node*/
+	spinlock_t sp_lock; /*lock for reference count & free list opertion*/
+	u32 total_num; /* Number of total pages*/
+	atomic_t free_num; /*number of free pages*/
+} mali_block_allocator;
+
+unsigned long _mali_blk_item_get_phy_addr(mali_block_item *item);
+unsigned long _mali_blk_item_get_pfn(mali_block_item *item);
+u32 mali_mem_block_get_ref_count(mali_page_node *node);
+u32 mali_mem_block_add_ref(mali_page_node *node);
+u32 mali_mem_block_dec_ref(mali_page_node *node);
+u32 mali_mem_block_release(mali_mem_backend *mem_bkend);
+int mali_mem_block_alloc(mali_mem_block_mem *block_mem, u32 size);
+int mali_mem_block_mali_map(mali_mem_block_mem *block_mem, struct mali_session_data *session, u32 vaddr, u32 props);
+void mali_mem_block_mali_unmap(mali_mem_allocation *alloc);
+
+int mali_mem_block_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma);
+_mali_osk_errcode_t mali_memory_core_resource_dedicated_memory(u32 start, u32 size);
+mali_bool mali_memory_have_dedicated_memory(void);
+u32 mali_mem_block_free(mali_mem_block_mem *block_mem);
+u32 mali_mem_block_free_list(struct list_head *list);
+void mali_mem_block_free_node(struct mali_page_node *node);
+void mali_mem_block_allocator_destroy(void);
+_mali_osk_errcode_t mali_mem_block_unref_node(struct mali_page_node *node);
+u32 mali_mem_block_allocator_stat(void);
+
+#endif /* __MALI_BLOCK_ALLOCATOR_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_cow.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_cow.c
@@ -0,0 +1,790 @@
+/*
+ * Copyright (C) 2013-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/mm.h>
+#include <linux/list.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/highmem.h>
+#include <asm/cacheflush.h>
+#include <linux/sched.h>
+#ifdef CONFIG_ARM
+#include <asm/outercache.h>
+#endif
+#include <asm/dma-mapping.h>
+
+#include "mali_memory.h"
+#include "mali_kernel_common.h"
+#include "mali_uk_types.h"
+#include "mali_osk.h"
+#include "mali_kernel_linux.h"
+#include "mali_memory_cow.h"
+#include "mali_memory_block_alloc.h"
+#include "mali_memory_swap_alloc.h"
+
+/**
+* allocate pages for COW backend and flush cache
+*/
+static struct page *mali_mem_cow_alloc_page(void)
+
+{
+	mali_mem_os_mem os_mem;
+	struct mali_page_node *node;
+	struct page *new_page;
+
+	int ret = 0;
+	/* allocate pages from os mem */
+	ret = mali_mem_os_alloc_pages(&os_mem, _MALI_OSK_MALI_PAGE_SIZE);
+
+	if (ret) {
+		return NULL;
+	}
+
+	MALI_DEBUG_ASSERT(1 == os_mem.count);
+
+	node = _MALI_OSK_CONTAINER_OF(os_mem.pages.next, struct mali_page_node, list);
+	new_page = node->page;
+	node->page = NULL;
+	list_del(&node->list);
+	kfree(node);
+
+	return new_page;
+}
+
+
+static struct list_head *_mali_memory_cow_get_node_list(mali_mem_backend *target_bk,
+		u32 target_offset,
+		u32 target_size)
+{
+	MALI_DEBUG_ASSERT(MALI_MEM_OS == target_bk->type || MALI_MEM_COW == target_bk->type ||
+			  MALI_MEM_BLOCK == target_bk->type || MALI_MEM_SWAP == target_bk->type);
+
+	if (MALI_MEM_OS == target_bk->type) {
+		MALI_DEBUG_ASSERT(&target_bk->os_mem);
+		MALI_DEBUG_ASSERT(((target_size + target_offset) / _MALI_OSK_MALI_PAGE_SIZE) <= target_bk->os_mem.count);
+		return &target_bk->os_mem.pages;
+	} else if (MALI_MEM_COW == target_bk->type) {
+		MALI_DEBUG_ASSERT(&target_bk->cow_mem);
+		MALI_DEBUG_ASSERT(((target_size + target_offset) / _MALI_OSK_MALI_PAGE_SIZE) <= target_bk->cow_mem.count);
+		return  &target_bk->cow_mem.pages;
+	} else if (MALI_MEM_BLOCK == target_bk->type) {
+		MALI_DEBUG_ASSERT(&target_bk->block_mem);
+		MALI_DEBUG_ASSERT(((target_size + target_offset) / _MALI_OSK_MALI_PAGE_SIZE) <= target_bk->block_mem.count);
+		return  &target_bk->block_mem.pfns;
+	} else if (MALI_MEM_SWAP == target_bk->type) {
+		MALI_DEBUG_ASSERT(&target_bk->swap_mem);
+		MALI_DEBUG_ASSERT(((target_size + target_offset) / _MALI_OSK_MALI_PAGE_SIZE) <= target_bk->swap_mem.count);
+		return  &target_bk->swap_mem.pages;
+	}
+
+	return NULL;
+}
+
+/**
+* Do COW for os memory - support do COW for memory from bank memory
+* The range_start/size can be zero, which means it will call cow_modify_range
+* latter.
+* This function allocate new pages for COW backend from os mem for a modified range
+* It will keep the page which not in the modified range and Add ref to it
+*
+* @target_bk - target allocation's backend(the allocation need to do COW)
+* @target_offset - the offset in target allocation to do COW(for support COW  a memory allocated from memory_bank, 4K align)
+* @target_size - size of target allocation to do COW (for support memory bank)
+* @backend -COW backend
+* @range_start - offset of modified range (4K align)
+* @range_size - size of modified range
+*/
+_mali_osk_errcode_t mali_memory_cow_os_memory(mali_mem_backend *target_bk,
+		u32 target_offset,
+		u32 target_size,
+		mali_mem_backend *backend,
+		u32 range_start,
+		u32 range_size)
+{
+	mali_mem_cow *cow = &backend->cow_mem;
+	struct mali_page_node *m_page, *m_tmp, *page_node;
+	int target_page = 0;
+	struct page *new_page;
+	struct list_head *pages = NULL;
+
+	pages = _mali_memory_cow_get_node_list(target_bk, target_offset, target_size);
+
+	if (NULL == pages) {
+		MALI_DEBUG_PRINT_ERROR(("No memory page  need to cow ! \n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	MALI_DEBUG_ASSERT(0 == cow->count);
+
+	INIT_LIST_HEAD(&cow->pages);
+	mutex_lock(&target_bk->mutex);
+	list_for_each_entry_safe(m_page, m_tmp, pages, list) {
+		/* add page from (target_offset,target_offset+size) to cow backend */
+		if ((target_page >= target_offset / _MALI_OSK_MALI_PAGE_SIZE) &&
+		    (target_page < ((target_size + target_offset) / _MALI_OSK_MALI_PAGE_SIZE))) {
+
+			/* allocate a new page node, alway use OS memory for COW */
+			page_node = _mali_page_node_allocate(MALI_PAGE_NODE_OS);
+
+			if (NULL == page_node) {
+				mutex_unlock(&target_bk->mutex);
+				goto error;
+			}
+
+			INIT_LIST_HEAD(&page_node->list);
+
+			/* check if in the modified range*/
+			if ((cow->count >= range_start / _MALI_OSK_MALI_PAGE_SIZE) &&
+			    (cow->count < (range_start + range_size) / _MALI_OSK_MALI_PAGE_SIZE)) {
+				/* need to allocate a new page */
+				/* To simplify the case, All COW memory is allocated from os memory ?*/
+				new_page = mali_mem_cow_alloc_page();
+
+				if (NULL == new_page) {
+					kfree(page_node);
+					mutex_unlock(&target_bk->mutex);
+					goto error;
+				}
+
+				_mali_page_node_add_page(page_node, new_page);
+			} else {
+				/*Add Block memory case*/
+				if (m_page->type != MALI_PAGE_NODE_BLOCK) {
+					_mali_page_node_add_page(page_node, m_page->page);
+				} else {
+					page_node->type = MALI_PAGE_NODE_BLOCK;
+					_mali_page_node_add_block_item(page_node, m_page->blk_it);
+				}
+
+				/* add ref to this page */
+				_mali_page_node_ref(m_page);
+			}
+
+			/* add it to COW backend page list */
+			list_add_tail(&page_node->list, &cow->pages);
+			cow->count++;
+		}
+		target_page++;
+	}
+	mutex_unlock(&target_bk->mutex);
+	return _MALI_OSK_ERR_OK;
+error:
+	mali_mem_cow_release(backend, MALI_FALSE);
+	return _MALI_OSK_ERR_FAULT;
+}
+
+_mali_osk_errcode_t mali_memory_cow_swap_memory(mali_mem_backend *target_bk,
+		u32 target_offset,
+		u32 target_size,
+		mali_mem_backend *backend,
+		u32 range_start,
+		u32 range_size)
+{
+	mali_mem_cow *cow = &backend->cow_mem;
+	struct mali_page_node *m_page, *m_tmp, *page_node;
+	int target_page = 0;
+	struct mali_swap_item *swap_item;
+	struct list_head *pages = NULL;
+
+	pages = _mali_memory_cow_get_node_list(target_bk, target_offset, target_size);
+	if (NULL == pages) {
+		MALI_DEBUG_PRINT_ERROR(("No swap memory page need to cow ! \n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	MALI_DEBUG_ASSERT(0 == cow->count);
+
+	INIT_LIST_HEAD(&cow->pages);
+	mutex_lock(&target_bk->mutex);
+
+	backend->flags |= MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN;
+
+	list_for_each_entry_safe(m_page, m_tmp, pages, list) {
+		/* add page from (target_offset,target_offset+size) to cow backend */
+		if ((target_page >= target_offset / _MALI_OSK_MALI_PAGE_SIZE) &&
+		    (target_page < ((target_size + target_offset) / _MALI_OSK_MALI_PAGE_SIZE))) {
+
+			/* allocate a new page node, use swap memory for COW memory swap cowed flag. */
+			page_node = _mali_page_node_allocate(MALI_PAGE_NODE_SWAP);
+
+			if (NULL == page_node) {
+				mutex_unlock(&target_bk->mutex);
+				goto error;
+			}
+
+			/* check if in the modified range*/
+			if ((cow->count >= range_start / _MALI_OSK_MALI_PAGE_SIZE) &&
+			    (cow->count < (range_start + range_size) / _MALI_OSK_MALI_PAGE_SIZE)) {
+				/* need to allocate a new page */
+				/* To simplify the case, All COW memory is allocated from os memory ?*/
+				swap_item = mali_mem_swap_alloc_swap_item();
+
+				if (NULL == swap_item) {
+					kfree(page_node);
+					mutex_unlock(&target_bk->mutex);
+					goto error;
+				}
+
+				swap_item->idx = mali_mem_swap_idx_alloc();
+
+				if (_MALI_OSK_BITMAP_INVALIDATE_INDEX == swap_item->idx) {
+					MALI_DEBUG_PRINT(1, ("Failed to allocate swap index in swap CoW.\n"));
+					kfree(page_node);
+					kfree(swap_item);
+					mutex_unlock(&target_bk->mutex);
+					goto error;
+				}
+
+				_mali_page_node_add_swap_item(page_node, swap_item);
+			} else {
+				_mali_page_node_add_swap_item(page_node, m_page->swap_it);
+
+				/* add ref to this page */
+				_mali_page_node_ref(m_page);
+			}
+
+			list_add_tail(&page_node->list, &cow->pages);
+			cow->count++;
+		}
+		target_page++;
+	}
+	mutex_unlock(&target_bk->mutex);
+
+	return _MALI_OSK_ERR_OK;
+error:
+	mali_mem_swap_release(backend, MALI_FALSE);
+	return _MALI_OSK_ERR_FAULT;
+
+}
+
+
+_mali_osk_errcode_t _mali_mem_put_page_node(mali_page_node *node)
+{
+	if (node->type == MALI_PAGE_NODE_OS) {
+		return mali_mem_os_put_page(node->page);
+	} else if (node->type == MALI_PAGE_NODE_BLOCK) {
+		return mali_mem_block_unref_node(node);
+	} else if (node->type == MALI_PAGE_NODE_SWAP) {
+		return _mali_mem_swap_put_page_node(node);
+	} else
+		MALI_DEBUG_ASSERT(0);
+	return _MALI_OSK_ERR_FAULT;
+}
+
+
+/**
+* Modify a range of a exist COW backend
+* @backend -COW backend
+* @range_start - offset of modified range (4K align)
+* @range_size - size of modified range(in byte)
+*/
+_mali_osk_errcode_t mali_memory_cow_modify_range(mali_mem_backend *backend,
+		u32 range_start,
+		u32 range_size)
+{
+	mali_mem_allocation *alloc = NULL;
+	struct mali_session_data *session;
+	mali_mem_cow *cow = &backend->cow_mem;
+	struct mali_page_node *m_page, *m_tmp;
+	LIST_HEAD(pages);
+	struct page *new_page;
+	u32 count = 0;
+	s32 change_pages_nr = 0;
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_OK;
+
+	if (range_start % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+	if (range_size % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+
+	alloc = backend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == backend->type);
+	MALI_DEBUG_ASSERT(((range_start + range_size) / _MALI_OSK_MALI_PAGE_SIZE) <= cow->count);
+
+	mutex_lock(&backend->mutex);
+
+	/* free pages*/
+	list_for_each_entry_safe(m_page, m_tmp, &cow->pages, list) {
+
+		/* check if in the modified range*/
+		if ((count >= range_start / _MALI_OSK_MALI_PAGE_SIZE) &&
+		    (count < (range_start + range_size) / _MALI_OSK_MALI_PAGE_SIZE)) {
+			if (MALI_PAGE_NODE_SWAP != m_page->type) {
+				new_page = mali_mem_cow_alloc_page();
+
+				if (NULL == new_page) {
+					goto error;
+				}
+				if (1 != _mali_page_node_get_ref_count(m_page))
+					change_pages_nr++;
+				/* unref old page*/
+				_mali_osk_mutex_wait(session->cow_lock);
+				if (_mali_mem_put_page_node(m_page)) {
+					__free_page(new_page);
+					_mali_osk_mutex_signal(session->cow_lock);
+					goto error;
+				}
+				_mali_osk_mutex_signal(session->cow_lock);
+				/* add new page*/
+				/* always use OS for COW*/
+				m_page->type = MALI_PAGE_NODE_OS;
+				_mali_page_node_add_page(m_page, new_page);
+			} else {
+				struct mali_swap_item *swap_item;
+
+				swap_item = mali_mem_swap_alloc_swap_item();
+
+				if (NULL == swap_item) {
+					goto error;
+				}
+
+				swap_item->idx = mali_mem_swap_idx_alloc();
+
+				if (_MALI_OSK_BITMAP_INVALIDATE_INDEX == swap_item->idx) {
+					MALI_DEBUG_PRINT(1, ("Failed to allocate swap index in swap CoW modify range.\n"));
+					kfree(swap_item);
+					goto error;
+				}
+
+				if (1 != _mali_page_node_get_ref_count(m_page)) {
+					change_pages_nr++;
+				}
+
+				if (_mali_mem_put_page_node(m_page)) {
+					mali_mem_swap_free_swap_item(swap_item);
+					goto error;
+				}
+
+				_mali_page_node_add_swap_item(m_page, swap_item);
+			}
+		}
+		count++;
+	}
+	cow->change_pages_nr  = change_pages_nr;
+
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == alloc->type);
+
+	/* ZAP cpu mapping(modified range), and do cpu mapping here if need */
+	if (NULL != alloc->cpu_mapping.vma) {
+		MALI_DEBUG_ASSERT(0 != alloc->backend_handle);
+		MALI_DEBUG_ASSERT(NULL != alloc->cpu_mapping.vma);
+		MALI_DEBUG_ASSERT(alloc->cpu_mapping.vma->vm_end - alloc->cpu_mapping.vma->vm_start >= range_size);
+
+		if (MALI_MEM_BACKEND_FLAG_SWAP_COWED != (backend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED)) {
+			zap_vma_ptes(alloc->cpu_mapping.vma, alloc->cpu_mapping.vma->vm_start + range_start, range_size);
+
+			ret = mali_mem_cow_cpu_map_pages_locked(backend, alloc->cpu_mapping.vma, alloc->cpu_mapping.vma->vm_start  + range_start, range_size / _MALI_OSK_MALI_PAGE_SIZE);
+
+			if (unlikely(ret != _MALI_OSK_ERR_OK)) {
+				MALI_DEBUG_PRINT(2, ("mali_memory_cow_modify_range: cpu mapping failed !\n"));
+				ret =  _MALI_OSK_ERR_FAULT;
+			}
+		} else {
+			/* used to trigger page fault for swappable cowed memory. */
+			alloc->cpu_mapping.vma->vm_flags |= VM_PFNMAP;
+			alloc->cpu_mapping.vma->vm_flags |= VM_MIXEDMAP;
+
+			zap_vma_ptes(alloc->cpu_mapping.vma, alloc->cpu_mapping.vma->vm_start + range_start, range_size);
+			/* delete this flag to let swappble is ummapped regard to stauct page not page frame. */
+			alloc->cpu_mapping.vma->vm_flags &= ~VM_PFNMAP;
+			alloc->cpu_mapping.vma->vm_flags &= ~VM_MIXEDMAP;
+		}
+	}
+
+error:
+	mutex_unlock(&backend->mutex);
+	return ret;
+
+}
+
+
+/**
+* Allocate pages for COW backend
+* @alloc  -allocation for COW allocation
+* @target_bk - target allocation's backend(the allocation need to do COW)
+* @target_offset - the offset in target allocation to do COW(for support COW  a memory allocated from memory_bank, 4K align)
+* @target_size - size of target allocation to do COW (for support memory bank)(in byte)
+* @backend -COW backend
+* @range_start - offset of modified range (4K align)
+* @range_size - size of modified range(in byte)
+*/
+_mali_osk_errcode_t mali_memory_do_cow(mali_mem_backend *target_bk,
+				       u32 target_offset,
+				       u32 target_size,
+				       mali_mem_backend *backend,
+				       u32 range_start,
+				       u32 range_size)
+{
+	struct mali_session_data *session = backend->mali_allocation->session;
+
+	MALI_CHECK_NON_NULL(session, _MALI_OSK_ERR_INVALID_ARGS);
+
+	/* size & offset must be a multiple of the system page size */
+	if (target_size % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+	if (range_size % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+	if (target_offset % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+	if (range_start % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+
+	/* check backend type */
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == backend->type);
+
+	switch (target_bk->type) {
+	case MALI_MEM_OS:
+	case MALI_MEM_BLOCK:
+		return mali_memory_cow_os_memory(target_bk, target_offset, target_size, backend, range_start, range_size);
+		break;
+	case MALI_MEM_COW:
+		if (backend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED) {
+			return mali_memory_cow_swap_memory(target_bk, target_offset, target_size, backend, range_start, range_size);
+		} else {
+			return mali_memory_cow_os_memory(target_bk, target_offset, target_size, backend, range_start, range_size);
+		}
+		break;
+	case MALI_MEM_SWAP:
+		return mali_memory_cow_swap_memory(target_bk, target_offset, target_size, backend, range_start, range_size);
+		break;
+	case MALI_MEM_EXTERNAL:
+		/*NOT support yet*/
+		MALI_DEBUG_PRINT_ERROR(("External physical memory not supported ! \n"));
+		return _MALI_OSK_ERR_UNSUPPORTED;
+		break;
+	case MALI_MEM_DMA_BUF:
+		/*NOT support yet*/
+		MALI_DEBUG_PRINT_ERROR(("DMA buffer not supported ! \n"));
+		return _MALI_OSK_ERR_UNSUPPORTED;
+		break;
+	case MALI_MEM_UMP:
+		/*NOT support yet*/
+		MALI_DEBUG_PRINT_ERROR(("UMP buffer not supported ! \n"));
+		return _MALI_OSK_ERR_UNSUPPORTED;
+		break;
+	default:
+		/*Not support yet*/
+		MALI_DEBUG_PRINT_ERROR(("Invalid memory type not supported ! \n"));
+		return _MALI_OSK_ERR_UNSUPPORTED;
+		break;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+
+/**
+* Map COW backend memory to mali
+* Support OS/BLOCK for mali_page_node
+*/
+int mali_mem_cow_mali_map(mali_mem_backend *mem_bkend, u32 range_start, u32 range_size)
+{
+	mali_mem_allocation *cow_alloc;
+	struct mali_page_node *m_page;
+	struct mali_session_data *session;
+	struct mali_page_directory *pagedir;
+	u32 virt, start;
+
+	cow_alloc = mem_bkend->mali_allocation;
+	virt = cow_alloc->mali_vma_node.vm_node.start;
+	start = virt;
+
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend);
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == mem_bkend->type);
+	MALI_DEBUG_ASSERT_POINTER(cow_alloc);
+
+	session = cow_alloc->session;
+	pagedir = session->page_directory;
+	MALI_CHECK_NON_NULL(session, _MALI_OSK_ERR_INVALID_ARGS);
+	list_for_each_entry(m_page, &mem_bkend->cow_mem.pages, list) {
+		if ((virt - start >= range_start) && (virt - start < range_start + range_size)) {
+			dma_addr_t phys = _mali_page_node_get_dma_addr(m_page);
+#if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT)
+			MALI_DEBUG_ASSERT(0 == (phys >> 32));
+#endif
+			mali_mmu_pagedir_update(pagedir, virt, (mali_dma_addr)phys,
+						MALI_MMU_PAGE_SIZE, MALI_MMU_FLAGS_DEFAULT);
+		}
+		virt += MALI_MMU_PAGE_SIZE;
+	}
+	return 0;
+}
+
+/**
+* Map COW backend to cpu
+* support OS/BLOCK memory
+*/
+int mali_mem_cow_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma)
+{
+	mali_mem_cow *cow = &mem_bkend->cow_mem;
+	struct mali_page_node *m_page;
+	int ret;
+	unsigned long addr = vma->vm_start;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_COW);
+
+	list_for_each_entry(m_page, &cow->pages, list) {
+		/* We should use vm_insert_page, but it does a dcache
+		 * flush which makes it way slower than remap_pfn_range or vm_insert_pfn.
+		ret = vm_insert_page(vma, addr, page);
+		*/
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+		ret = vmf_insert_pfn(vma, addr, _mali_page_node_get_pfn(m_page));
+		if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+		ret = vm_insert_pfn(vma, addr, _mali_page_node_get_pfn(m_page));
+		if (unlikely(0 != ret)) {
+#endif
+
+			return ret;
+		}
+		addr += _MALI_OSK_MALI_PAGE_SIZE;
+	}
+
+	return 0;
+}
+
+/**
+* Map some pages(COW backend) to CPU vma@vaddr
+*@ mem_bkend - COW backend
+*@ vma
+*@ vaddr -start CPU vaddr mapped to
+*@ num - max number of pages to map to CPU vaddr
+*/
+_mali_osk_errcode_t mali_mem_cow_cpu_map_pages_locked(mali_mem_backend *mem_bkend,
+		struct vm_area_struct *vma,
+		unsigned long vaddr,
+		int num)
+{
+	mali_mem_cow *cow = &mem_bkend->cow_mem;
+	struct mali_page_node *m_page;
+	int ret;
+	int offset;
+	int count ;
+	unsigned long vstart = vma->vm_start;
+	count = 0;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_COW);
+	MALI_DEBUG_ASSERT(0 == vaddr % _MALI_OSK_MALI_PAGE_SIZE);
+	MALI_DEBUG_ASSERT(0 == vstart % _MALI_OSK_MALI_PAGE_SIZE);
+	offset = (vaddr - vstart) / _MALI_OSK_MALI_PAGE_SIZE;
+
+	list_for_each_entry(m_page, &cow->pages, list) {
+		if ((count >= offset) && (count < offset + num)) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+			ret = vmf_insert_pfn(vma, vaddr, _mali_page_node_get_pfn(m_page));
+			if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+			ret = vm_insert_pfn(vma, vaddr, _mali_page_node_get_pfn(m_page));
+			if (unlikely(0 != ret)) {
+#endif
+
+				if (count == offset) {
+					return _MALI_OSK_ERR_FAULT;
+				} else {
+					/* ret is EBUSY when page isn't in modify range, but now it's OK*/
+					return _MALI_OSK_ERR_OK;
+				}
+			}
+			vaddr += _MALI_OSK_MALI_PAGE_SIZE;
+		}
+		count++;
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+/**
+* Release COW backend memory
+* free it directly(put_page--unref page), not put into pool
+*/
+u32 mali_mem_cow_release(mali_mem_backend *mem_bkend, mali_bool is_mali_mapped)
+{
+	mali_mem_allocation *alloc;
+	struct mali_session_data *session;
+	u32 free_pages_nr = 0;
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend);
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == mem_bkend->type);
+	alloc = mem_bkend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (MALI_MEM_BACKEND_FLAG_SWAP_COWED != (MALI_MEM_BACKEND_FLAG_SWAP_COWED & mem_bkend->flags)) {
+		/* Unmap the memory from the mali virtual address space. */
+		if (MALI_TRUE == is_mali_mapped)
+			mali_mem_os_mali_unmap(alloc);
+		/* free cow backend list*/
+		_mali_osk_mutex_wait(session->cow_lock);
+		free_pages_nr = mali_mem_os_free(&mem_bkend->cow_mem.pages, mem_bkend->cow_mem.count, MALI_TRUE);
+		_mali_osk_mutex_signal(session->cow_lock);
+
+		free_pages_nr += mali_mem_block_free_list(&mem_bkend->cow_mem.pages);
+
+		MALI_DEBUG_ASSERT(list_empty(&mem_bkend->cow_mem.pages));
+	} else {
+		free_pages_nr = mali_mem_swap_release(mem_bkend, is_mali_mapped);
+	}
+
+
+	MALI_DEBUG_PRINT(4, ("COW Mem free : allocated size = 0x%x, free size = 0x%x\n", mem_bkend->cow_mem.count * _MALI_OSK_MALI_PAGE_SIZE,
+			     free_pages_nr * _MALI_OSK_MALI_PAGE_SIZE));
+
+	mem_bkend->cow_mem.count = 0;
+	return free_pages_nr;
+}
+
+
+/* Dst node could os node or swap node. */
+void _mali_mem_cow_copy_page(mali_page_node *src_node, mali_page_node *dst_node)
+{
+	void *dst, *src;
+	struct page *dst_page;
+	dma_addr_t dma_addr;
+
+	MALI_DEBUG_ASSERT(src_node != NULL);
+	MALI_DEBUG_ASSERT(dst_node != NULL);
+	MALI_DEBUG_ASSERT(dst_node->type == MALI_PAGE_NODE_OS
+			  || dst_node->type == MALI_PAGE_NODE_SWAP);
+
+	if (dst_node->type == MALI_PAGE_NODE_OS) {
+		dst_page = dst_node->page;
+	} else {
+		dst_page = dst_node->swap_it->page;
+	}
+
+	dma_unmap_page(&mali_platform_device->dev, _mali_page_node_get_dma_addr(dst_node),
+		       _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+
+	/* map it , and copy the content*/
+	dst = kmap_atomic(dst_page);
+
+	if (src_node->type == MALI_PAGE_NODE_OS ||
+	    src_node->type == MALI_PAGE_NODE_SWAP) {
+		struct page *src_page;
+
+		if (src_node->type == MALI_PAGE_NODE_OS) {
+			src_page = src_node->page;
+		} else {
+			src_page = src_node->swap_it->page;
+		}
+
+		/* Clear and invaliate cache */
+		/* In ARM architecture, speculative read may pull stale data into L1 cache
+		 * for kernel linear mapping page table. DMA_BIDIRECTIONAL could
+		 * invalidate the L1 cache so that following read get the latest data
+		*/
+		dma_unmap_page(&mali_platform_device->dev, _mali_page_node_get_dma_addr(src_node),
+			       _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+
+		src = kmap_atomic(src_page);
+		memcpy(dst, src , _MALI_OSK_MALI_PAGE_SIZE);
+		kunmap_atomic(src);
+		dma_addr = dma_map_page(&mali_platform_device->dev, src_page,
+					0, _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+
+		if (src_node->type == MALI_PAGE_NODE_SWAP) {
+			src_node->swap_it->dma_addr = dma_addr;
+		}
+	} else if (src_node->type == MALI_PAGE_NODE_BLOCK) {
+		/*
+		* use ioremap to map src for BLOCK memory
+		*/
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+		src = ioremap(_mali_page_node_get_dma_addr(src_node), _MALI_OSK_MALI_PAGE_SIZE);
+#else
+		src = ioremap_nocache(_mali_page_node_get_dma_addr(src_node), _MALI_OSK_MALI_PAGE_SIZE);
+#endif
+		memcpy(dst, src , _MALI_OSK_MALI_PAGE_SIZE);
+		iounmap(src);
+	}
+	kunmap_atomic(dst);
+	dma_addr = dma_map_page(&mali_platform_device->dev, dst_page,
+				0, _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+
+	if (dst_node->type == MALI_PAGE_NODE_SWAP) {
+		dst_node->swap_it->dma_addr = dma_addr;
+	}
+}
+
+
+/*
+* allocate page on demand when CPU access it,
+* THis used in page fault handler
+*/
+_mali_osk_errcode_t mali_mem_cow_allocate_on_demand(mali_mem_backend *mem_bkend, u32 offset_page)
+{
+	struct page *new_page = NULL;
+	struct mali_page_node *new_node = NULL;
+	int i = 0;
+	struct mali_page_node *m_page, *found_node = NULL;
+	struct  mali_session_data *session = NULL;
+	mali_mem_cow *cow = &mem_bkend->cow_mem;
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == mem_bkend->type);
+	MALI_DEBUG_ASSERT(offset_page < mem_bkend->size / _MALI_OSK_MALI_PAGE_SIZE);
+	MALI_DEBUG_PRINT(4, ("mali_mem_cow_allocate_on_demand !, offset_page =0x%x\n", offset_page));
+
+	/* allocate new page here */
+	new_page = mali_mem_cow_alloc_page();
+	if (!new_page)
+		return _MALI_OSK_ERR_NOMEM;
+
+	new_node = _mali_page_node_allocate(MALI_PAGE_NODE_OS);
+	if (!new_node) {
+		__free_page(new_page);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	/* find the page in backend*/
+	list_for_each_entry(m_page, &cow->pages, list) {
+		if (i == offset_page) {
+			found_node = m_page;
+			break;
+		}
+		i++;
+	}
+	MALI_DEBUG_ASSERT(found_node);
+	if (NULL == found_node) {
+		__free_page(new_page);
+		kfree(new_node);
+		return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	}
+
+	_mali_page_node_add_page(new_node, new_page);
+
+	/* Copy the src page's content to new page */
+	_mali_mem_cow_copy_page(found_node, new_node);
+
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend->mali_allocation);
+	session = mem_bkend->mali_allocation->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+	if (1 != _mali_page_node_get_ref_count(found_node)) {
+		atomic_add(1, &session->mali_mem_allocated_pages);
+		if (atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > session->max_mali_mem_allocated_size) {
+			session->max_mali_mem_allocated_size = atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+		}
+		mem_bkend->cow_mem.change_pages_nr++;
+	}
+
+	_mali_osk_mutex_wait(session->cow_lock);
+	if (_mali_mem_put_page_node(found_node)) {
+		__free_page(new_page);
+		kfree(new_node);
+		_mali_osk_mutex_signal(session->cow_lock);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+	_mali_osk_mutex_signal(session->cow_lock);
+
+	list_replace(&found_node->list, &new_node->list);
+
+	kfree(found_node);
+
+	/* map to GPU side*/
+	_mali_osk_mutex_wait(session->memory_lock);
+	mali_mem_cow_mali_map(mem_bkend, offset_page * _MALI_OSK_MALI_PAGE_SIZE, _MALI_OSK_MALI_PAGE_SIZE);
+	_mali_osk_mutex_signal(session->memory_lock);
+	return _MALI_OSK_ERR_OK;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_cow.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_cow.h
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_COW_H__
+#define __MALI_MEMORY_COW_H__
+
+#include "mali_osk.h"
+#include "mali_session.h"
+#include "mali_memory_types.h"
+
+int mali_mem_cow_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma);
+_mali_osk_errcode_t mali_mem_cow_cpu_map_pages_locked(mali_mem_backend *mem_bkend,
+		struct vm_area_struct *vma,
+		unsigned long vaddr,
+		int num);
+
+_mali_osk_errcode_t mali_memory_do_cow(mali_mem_backend *target_bk,
+				       u32 target_offset,
+				       u32 target_size,
+				       mali_mem_backend *backend,
+				       u32 range_start,
+				       u32 range_size);
+
+_mali_osk_errcode_t mali_memory_cow_modify_range(mali_mem_backend *backend,
+		u32 range_start,
+		u32 range_size);
+
+_mali_osk_errcode_t mali_memory_cow_os_memory(mali_mem_backend *target_bk,
+		u32 target_offset,
+		u32 target_size,
+		mali_mem_backend *backend,
+		u32 range_start,
+		u32 range_size);
+
+void _mali_mem_cow_copy_page(mali_page_node *src_node, mali_page_node *dst_node);
+
+int mali_mem_cow_mali_map(mali_mem_backend *mem_bkend, u32 range_start, u32 range_size);
+u32 mali_mem_cow_release(mali_mem_backend *mem_bkend, mali_bool is_mali_mapped);
+_mali_osk_errcode_t mali_mem_cow_allocate_on_demand(mali_mem_backend *mem_bkend, u32 offset_page);
+#endif
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_defer_bind.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_defer_bind.c
@@ -0,0 +1,262 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/mm.h>
+#include <linux/list.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/highmem.h>
+#include <asm/cacheflush.h>
+#include <linux/sched.h>
+#ifdef CONFIG_ARM
+#include <asm/outercache.h>
+#endif
+#include <asm/dma-mapping.h>
+
+#include "mali_memory.h"
+#include "mali_kernel_common.h"
+#include "mali_uk_types.h"
+#include "mali_osk.h"
+#include "mali_kernel_linux.h"
+#include "mali_memory_defer_bind.h"
+#include "mali_executor.h"
+#include "mali_osk.h"
+#include "mali_scheduler.h"
+#include "mali_gp_job.h"
+
+mali_defer_bind_manager *mali_dmem_man = NULL;
+
+static u32 mali_dmem_get_gp_varying_size(struct mali_gp_job *gp_job)
+{
+	return gp_job->required_varying_memsize / _MALI_OSK_MALI_PAGE_SIZE;
+}
+
+_mali_osk_errcode_t mali_mem_defer_bind_manager_init(void)
+{
+	mali_dmem_man = _mali_osk_calloc(1, sizeof(struct mali_defer_bind_manager));
+	if (!mali_dmem_man)
+		return _MALI_OSK_ERR_NOMEM;
+
+	atomic_set(&mali_dmem_man->num_used_pages, 0);
+	atomic_set(&mali_dmem_man->num_dmem, 0);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+
+void mali_mem_defer_bind_manager_destory(void)
+{
+	if (mali_dmem_man) {
+		MALI_DEBUG_ASSERT(0 == atomic_read(&mali_dmem_man->num_dmem));
+		kfree(mali_dmem_man);
+	}
+	mali_dmem_man = NULL;
+}
+
+
+/*allocate pages from OS memory*/
+_mali_osk_errcode_t mali_mem_defer_alloc_mem(u32 require, struct mali_session_data *session, mali_defer_mem_block *dblock)
+{
+	int retval = 0;
+	u32 num_pages = require;
+	mali_mem_os_mem os_mem;
+
+	retval = mali_mem_os_alloc_pages(&os_mem, num_pages * _MALI_OSK_MALI_PAGE_SIZE);
+
+	/* add to free pages list */
+	if (0 == retval) {
+		MALI_DEBUG_PRINT(4, ("mali_mem_defer_alloc_mem ,,*** pages allocate = 0x%x \n", num_pages));
+		list_splice(&os_mem.pages, &dblock->free_pages);
+		atomic_add(os_mem.count, &dblock->num_free_pages);
+		atomic_add(os_mem.count, &session->mali_mem_allocated_pages);
+		if (atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > session->max_mali_mem_allocated_size) {
+			session->max_mali_mem_allocated_size = atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+		}
+		return _MALI_OSK_ERR_OK;
+	} else
+		return _MALI_OSK_ERR_FAULT;
+}
+
+_mali_osk_errcode_t mali_mem_prepare_mem_for_job(struct mali_gp_job *next_gp_job, mali_defer_mem_block *dblock)
+{
+	u32 require_page;
+
+	if (!next_gp_job)
+		return _MALI_OSK_ERR_FAULT;
+
+	require_page = mali_dmem_get_gp_varying_size(next_gp_job);
+
+	MALI_DEBUG_PRINT(4, ("mali_mem_defer_prepare_mem_work, require alloc page 0x%x\n",
+			     require_page));
+	/* allocate more pages from OS */
+	if (_MALI_OSK_ERR_OK != mali_mem_defer_alloc_mem(require_page, next_gp_job->session, dblock)) {
+		MALI_DEBUG_PRINT(1, ("ERROR##mali_mem_defer_prepare_mem_work, allocate page failed!!"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	next_gp_job->bind_flag = MALI_DEFER_BIND_MEMORY_PREPARED;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+
+/* do preparetion for allocation before defer bind */
+_mali_osk_errcode_t mali_mem_defer_bind_allocation_prepare(mali_mem_allocation *alloc, struct list_head *list, u32 *required_varying_memsize)
+{
+	mali_mem_backend *mem_bkend = NULL;
+	struct mali_backend_bind_list *bk_list = _mali_osk_calloc(1, sizeof(struct mali_backend_bind_list));
+	if (NULL == bk_list)
+		return _MALI_OSK_ERR_FAULT;
+
+	INIT_LIST_HEAD(&bk_list->node);
+	/* Get backend memory */
+	mutex_lock(&mali_idr_mutex);
+	if (!(mem_bkend = idr_find(&mali_backend_idr, alloc->backend_handle))) {
+		MALI_DEBUG_PRINT(1, ("Can't find memory backend in defer bind!\n"));
+		mutex_unlock(&mali_idr_mutex);
+		_mali_osk_free(bk_list);
+		return _MALI_OSK_ERR_FAULT;
+	}
+	mutex_unlock(&mali_idr_mutex);
+
+	/* If the mem backend has already been bound, no need to bind again.*/
+	if (mem_bkend->os_mem.count > 0) {
+		_mali_osk_free(bk_list);
+		return _MALI_OSK_ERR_OK;
+	}
+
+	MALI_DEBUG_PRINT(4, ("bind_allocation_prepare:: allocation =%x vaddr=0x%x!\n", alloc, alloc->mali_vma_node.vm_node.start));
+
+	INIT_LIST_HEAD(&mem_bkend->os_mem.pages);
+
+	bk_list->bkend = mem_bkend;
+	bk_list->vaddr = alloc->mali_vma_node.vm_node.start;
+	bk_list->session = alloc->session;
+	bk_list->page_num = mem_bkend->size / _MALI_OSK_MALI_PAGE_SIZE;
+	*required_varying_memsize +=  mem_bkend->size;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_OS);
+
+	/* add to job to do list */
+	list_add(&bk_list->node, list);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+
+
+/* bind phyiscal memory to allocation
+This function will be called in IRQ handler*/
+static _mali_osk_errcode_t mali_mem_defer_bind_allocation(struct mali_backend_bind_list *bk_node,
+		struct list_head *pages)
+{
+	struct mali_session_data *session = bk_node->session;
+	mali_mem_backend *mem_bkend = bk_node->bkend;
+	MALI_DEBUG_PRINT(4, ("mali_mem_defer_bind_allocation, bind bkend = %x page num=0x%x vaddr=%x session=%x\n", mem_bkend, bk_node->page_num, bk_node->vaddr, session));
+
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_OS);
+	list_splice(pages, &mem_bkend->os_mem.pages);
+	mem_bkend->os_mem.count = bk_node->page_num;
+
+	if (mem_bkend->type == MALI_MEM_OS) {
+		mali_mem_os_mali_map(&mem_bkend->os_mem, session, bk_node->vaddr, 0,
+				     mem_bkend->os_mem.count, MALI_MMU_FLAGS_DEFAULT);
+	}
+	smp_wmb();
+	bk_node->flag = MALI_DEFER_BIND_MEMORY_BINDED;
+	mem_bkend->flags &= ~MALI_MEM_BACKEND_FLAG_NOT_BINDED;
+	mem_bkend->flags |= MALI_MEM_BACKEND_FLAG_BINDED;
+	return _MALI_OSK_ERR_OK;
+}
+
+
+static struct list_head *mali_mem_defer_get_free_page_list(u32 count, struct list_head *pages, mali_defer_mem_block *dblock)
+{
+	int i = 0;
+	struct mali_page_node *m_page, *m_tmp;
+
+	if (atomic_read(&dblock->num_free_pages) < count) {
+		return NULL;
+	} else {
+		list_for_each_entry_safe(m_page, m_tmp, &dblock->free_pages, list) {
+			if (i < count) {
+				list_move_tail(&m_page->list, pages);
+			} else {
+				break;
+			}
+			i++;
+		}
+		MALI_DEBUG_ASSERT(i == count);
+		atomic_sub(count, &dblock->num_free_pages);
+		return pages;
+	}
+}
+
+
+/* called in job start IOCTL to bind physical memory for each allocations
+@ bk_list backend list to do defer bind
+@ pages page list to do this bind
+@ count number of pages
+*/
+_mali_osk_errcode_t mali_mem_defer_bind(struct mali_gp_job *gp,
+					struct mali_defer_mem_block *dmem_block)
+{
+	struct mali_defer_mem *dmem = NULL;
+	struct mali_backend_bind_list *bkn, *bkn_tmp;
+	LIST_HEAD(pages);
+
+	if (gp->required_varying_memsize != (atomic_read(&dmem_block->num_free_pages) * _MALI_OSK_MALI_PAGE_SIZE)) {
+		MALI_DEBUG_PRINT_ERROR(("#BIND:  The memsize of varying buffer not match to the pagesize of the dmem_block!!## \n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	MALI_DEBUG_PRINT(4, ("#BIND: GP job=%x## \n", gp));
+	dmem = (mali_defer_mem *)_mali_osk_calloc(1, sizeof(struct mali_defer_mem));
+	if (dmem) {
+		INIT_LIST_HEAD(&dmem->node);
+		gp->dmem = dmem;
+	} else {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	atomic_add(1, &mali_dmem_man->num_dmem);
+	/* for each bk_list backend, do bind */
+	list_for_each_entry_safe(bkn, bkn_tmp , &gp->vary_todo, node) {
+		INIT_LIST_HEAD(&pages);
+		if (likely(mali_mem_defer_get_free_page_list(bkn->page_num, &pages, dmem_block))) {
+			list_del(&bkn->node);
+			mali_mem_defer_bind_allocation(bkn, &pages);
+			_mali_osk_free(bkn);
+		} else {
+			/* not enough memory will not happen */
+			MALI_DEBUG_PRINT_ERROR(("#BIND: NOT enough memory when binded !!## \n"));
+			_mali_osk_free(gp->dmem);
+			return _MALI_OSK_ERR_NOMEM;
+		}
+	}
+
+	if (!list_empty(&gp->vary_todo)) {
+		MALI_DEBUG_PRINT_ERROR(("#BIND:  The deferbind backend list isn't empty !!## \n"));
+		_mali_osk_free(gp->dmem);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	dmem->flag = MALI_DEFER_BIND_MEMORY_BINDED;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mem_defer_dmem_free(struct mali_gp_job *gp)
+{
+	if (gp->dmem) {
+		atomic_dec(&mali_dmem_man->num_dmem);
+		_mali_osk_free(gp->dmem);
+	}
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_defer_bind.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_defer_bind.h
@@ -0,0 +1,64 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#ifndef __MALI_MEMORY_DEFER_BIND_H_
+#define __MALI_MEMORY_DEFER_BIND_H_
+
+
+#include "mali_osk.h"
+#include "mali_session.h"
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/rbtree.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+
+#include "mali_memory_types.h"
+#include "mali_memory_os_alloc.h"
+#include "mali_uk_types.h"
+
+struct mali_gp_job;
+
+typedef struct mali_defer_mem {
+	struct list_head node;   /*dlist node in bind manager */
+	u32 flag;
+} mali_defer_mem;
+
+
+typedef struct mali_defer_mem_block {
+	struct list_head free_pages; /* page pool */
+	atomic_t num_free_pages;
+} mali_defer_mem_block;
+
+/* varying memory list need to bind */
+typedef struct mali_backend_bind_list {
+	struct list_head node;
+	struct mali_mem_backend *bkend;
+	u32 vaddr;
+	u32 page_num;
+	struct mali_session_data *session;
+	u32 flag;
+} mali_backend_bind_lists;
+
+
+typedef struct mali_defer_bind_manager {
+	atomic_t num_used_pages;
+	atomic_t num_dmem;
+} mali_defer_bind_manager;
+
+_mali_osk_errcode_t mali_mem_defer_bind_manager_init(void);
+void mali_mem_defer_bind_manager_destory(void);
+_mali_osk_errcode_t mali_mem_defer_bind(struct mali_gp_job *gp, struct mali_defer_mem_block *dmem_block);
+_mali_osk_errcode_t mali_mem_defer_bind_allocation_prepare(mali_mem_allocation *alloc, struct list_head *list,  u32 *required_varying_memsize);
+_mali_osk_errcode_t mali_mem_prepare_mem_for_job(struct mali_gp_job *next_gp_job, mali_defer_mem_block *dblock);
+void mali_mem_defer_dmem_free(struct mali_gp_job *gp);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_dma_buf.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_dma_buf.c
@@ -0,0 +1,407 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/fs.h>      /* file system operations */
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+#include <linux/dma-buf.h>
+#include <linux/scatterlist.h>
+#include <linux/rbtree.h>
+#include <linux/platform_device.h>
+#include <linux/wait.h>
+#include <linux/sched.h>
+#include <linux/mutex.h>
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_kernel_linux.h"
+
+#include "mali_memory.h"
+#include "mali_memory_dma_buf.h"
+#include "mali_memory_virtual.h"
+#include "mali_pp_job.h"
+
+/*
+ * Map DMA buf attachment \a mem into \a session at virtual address \a virt.
+ */
+static int mali_dma_buf_map(mali_mem_backend *mem_backend)
+{
+	mali_mem_allocation *alloc;
+	struct mali_dma_buf_attachment *mem;
+	struct  mali_session_data *session;
+	struct mali_page_directory *pagedir;
+	_mali_osk_errcode_t err;
+	struct scatterlist *sg;
+	u32 virt, flags, unmap_dma_size;
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+
+	alloc = mem_backend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	mem = mem_backend->dma_buf.attachment;
+	MALI_DEBUG_ASSERT_POINTER(mem);
+	MALI_DEBUG_ASSERT_POINTER(mem->buf);
+	unmap_dma_size = mem->buf->size;
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT(mem->session == session);
+
+	virt = alloc->mali_vma_node.vm_node.start;
+	flags = alloc->flags;
+
+	mali_session_memory_lock(session);
+	mem->map_ref++;
+
+	MALI_DEBUG_PRINT(5, ("Mali DMA-buf: map attachment %p, new map_ref = %d\n", mem, mem->map_ref));
+#if (!defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)) && (defined(CONFIG_MALI_DMA_BUF_LAZY_MAP))
+	if (MALI_FALSE == mem->is_mapped)
+#else
+	if (1 == mem->map_ref)
+#endif
+	{
+		/* First reference taken, so we need to map the dma buf */
+		MALI_DEBUG_ASSERT(!mem->is_mapped);
+
+		mem->sgt = dma_buf_map_attachment(mem->attachment, DMA_BIDIRECTIONAL);
+		if (IS_ERR_OR_NULL(mem->sgt)) {
+			MALI_DEBUG_PRINT_ERROR(("Failed to map dma-buf attachment\n"));
+			mem->map_ref--;
+			mali_session_memory_unlock(session);
+			return -EFAULT;
+		}
+
+		err = mali_mem_mali_map_prepare(alloc);
+		if (_MALI_OSK_ERR_OK != err) {
+			MALI_DEBUG_PRINT(1, ("Mapping of DMA memory failed\n"));
+			mem->map_ref--;
+			mali_session_memory_unlock(session);
+			return -ENOMEM;
+		}
+
+		pagedir = mali_session_get_page_directory(session);
+		MALI_DEBUG_ASSERT_POINTER(pagedir);
+
+		for_each_sg(mem->sgt->sgl, sg, mem->sgt->nents, i) {
+			u32 size = sg_dma_len(sg);
+			dma_addr_t phys = sg_dma_address(sg);
+
+			unmap_dma_size -= size;
+			/* sg must be page aligned. */
+			MALI_DEBUG_ASSERT(0 == size % MALI_MMU_PAGE_SIZE);
+			MALI_DEBUG_ASSERT(0 == (phys & ~(uintptr_t)0xFFFFFFFF));
+
+			mali_mmu_pagedir_update(pagedir, virt, phys, size, MALI_MMU_FLAGS_DEFAULT);
+
+			virt += size;
+		}
+
+		if (flags & MALI_MEM_FLAG_MALI_GUARD_PAGE) {
+			u32 guard_phys;
+			MALI_DEBUG_PRINT(7, ("Mapping in extra guard page\n"));
+
+			guard_phys = sg_dma_address(mem->sgt->sgl);
+			mali_mmu_pagedir_update(pagedir, virt, guard_phys, MALI_MMU_PAGE_SIZE, MALI_MMU_FLAGS_DEFAULT);
+		}
+
+		mem->is_mapped = MALI_TRUE;
+
+		if (0 != unmap_dma_size) {
+			MALI_DEBUG_PRINT_ERROR(("The dma buf size isn't equal to the total scatterlists' dma length.\n"));
+			mali_session_memory_unlock(session);
+			return -EFAULT;
+		}
+
+		/* Wake up any thread waiting for buffer to become mapped */
+		wake_up_all(&mem->wait_queue);
+
+		mali_session_memory_unlock(session);
+	} else {
+		MALI_DEBUG_ASSERT(mem->is_mapped);
+		mali_session_memory_unlock(session);
+	}
+
+	return 0;
+}
+
+static void mali_dma_buf_unmap(mali_mem_allocation *alloc, struct mali_dma_buf_attachment *mem)
+{
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	MALI_DEBUG_ASSERT_POINTER(mem);
+	MALI_DEBUG_ASSERT_POINTER(mem->attachment);
+	MALI_DEBUG_ASSERT_POINTER(mem->buf);
+	MALI_DEBUG_ASSERT_POINTER(alloc->session);
+
+	mali_session_memory_lock(alloc->session);
+	mem->map_ref--;
+
+	MALI_DEBUG_PRINT(5, ("Mali DMA-buf: unmap attachment %p, new map_ref = %d\n", mem, mem->map_ref));
+
+	if (0 == mem->map_ref) {
+		if (NULL != mem->sgt) {
+			dma_buf_unmap_attachment(mem->attachment, mem->sgt, DMA_BIDIRECTIONAL);
+			mem->sgt = NULL;
+		}
+		if (MALI_TRUE == mem->is_mapped) {
+			mali_mem_mali_map_free(alloc->session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+					       alloc->flags);
+		}
+		mem->is_mapped = MALI_FALSE;
+	}
+
+	/* Wake up any thread waiting for buffer to become unmapped */
+	wake_up_all(&mem->wait_queue);
+
+	mali_session_memory_unlock(alloc->session);
+}
+
+#if !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+int mali_dma_buf_map_job(struct mali_pp_job *job)
+{
+	struct mali_dma_buf_attachment *mem;
+	_mali_osk_errcode_t err;
+	int i;
+	int ret = 0;
+	u32 num_memory_cookies;
+	struct mali_session_data *session;
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_allocation *mali_alloc = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	num_memory_cookies = mali_pp_job_num_memory_cookies(job);
+
+	session = mali_pp_job_get_session(job);
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	for (i = 0; i < num_memory_cookies; i++) {
+		u32 mali_addr  = mali_pp_job_get_memory_cookie(job, i);
+		mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_addr, 0);
+		MALI_DEBUG_ASSERT(NULL != mali_vma_node);
+		mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+		MALI_DEBUG_ASSERT(NULL != mali_alloc);
+		if (MALI_MEM_DMA_BUF != mali_alloc->type) {
+			continue;
+		}
+
+		/* Get backend memory & Map on CPU */
+		mutex_lock(&mali_idr_mutex);
+		mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle);
+		mutex_unlock(&mali_idr_mutex);
+		MALI_DEBUG_ASSERT(NULL != mem_bkend);
+
+		mem = mem_bkend->dma_buf.attachment;
+
+		MALI_DEBUG_ASSERT_POINTER(mem);
+		MALI_DEBUG_ASSERT(mem->session == mali_pp_job_get_session(job));
+
+		err = mali_dma_buf_map(mem_bkend);
+		if (0 != err) {
+			MALI_DEBUG_PRINT_ERROR(("Mali DMA-buf: Failed to map dma-buf for mali address %x\n", mali_addr));
+			ret = -EFAULT;
+			continue;
+		}
+	}
+	return ret;
+}
+
+void mali_dma_buf_unmap_job(struct mali_pp_job *job)
+{
+	struct mali_dma_buf_attachment *mem;
+	int i;
+	u32 num_memory_cookies;
+	struct mali_session_data *session;
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_allocation *mali_alloc = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	num_memory_cookies = mali_pp_job_num_memory_cookies(job);
+
+	session = mali_pp_job_get_session(job);
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	for (i = 0; i < num_memory_cookies; i++) {
+		u32 mali_addr  = mali_pp_job_get_memory_cookie(job, i);
+		mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_addr, 0);
+		MALI_DEBUG_ASSERT(NULL != mali_vma_node);
+		mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+		MALI_DEBUG_ASSERT(NULL != mali_alloc);
+		if (MALI_MEM_DMA_BUF != mali_alloc->type) {
+			continue;
+		}
+
+		/* Get backend memory & Map on CPU */
+		mutex_lock(&mali_idr_mutex);
+		mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle);
+		mutex_unlock(&mali_idr_mutex);
+		MALI_DEBUG_ASSERT(NULL != mem_bkend);
+
+		mem = mem_bkend->dma_buf.attachment;
+
+		MALI_DEBUG_ASSERT_POINTER(mem);
+		MALI_DEBUG_ASSERT(mem->session == mali_pp_job_get_session(job));
+		mali_dma_buf_unmap(mem_bkend->mali_allocation, mem);
+	}
+}
+#endif /* !CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH */
+
+int mali_dma_buf_get_size(struct mali_session_data *session, _mali_uk_dma_buf_get_size_s __user *user_arg)
+{
+	_mali_uk_dma_buf_get_size_s args;
+	int fd;
+	struct dma_buf *buf;
+
+	/* get call arguments from user space. copy_from_user returns how many bytes which where NOT copied */
+	if (0 != copy_from_user(&args, (void __user *)user_arg, sizeof(_mali_uk_dma_buf_get_size_s))) {
+		return -EFAULT;
+	}
+
+	/* Do DMA-BUF stuff */
+	fd = args.mem_fd;
+
+	buf = dma_buf_get(fd);
+	if (IS_ERR_OR_NULL(buf)) {
+		MALI_DEBUG_PRINT_ERROR(("Failed to get dma-buf from fd: %d\n", fd));
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 7, 0)
+		return PTR_ERR_OR_ZERO(buf);
+#else
+		return PTR_RET(buf);
+#endif
+	}
+
+	if (0 != put_user(buf->size, &user_arg->size)) {
+		dma_buf_put(buf);
+		return -EFAULT;
+	}
+
+	dma_buf_put(buf);
+
+	return 0;
+}
+
+_mali_osk_errcode_t mali_mem_bind_dma_buf(mali_mem_allocation *alloc,
+		mali_mem_backend *mem_backend,
+		int fd, u32 flags)
+{
+	struct dma_buf *buf;
+	struct mali_dma_buf_attachment *dma_mem;
+	struct  mali_session_data *session = alloc->session;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	/* get dma buffer */
+	buf = dma_buf_get(fd);
+	if (IS_ERR_OR_NULL(buf)) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* Currently, mapping of the full buffer are supported. */
+	if (alloc->psize != buf->size) {
+		goto failed_alloc_mem;
+	}
+
+	dma_mem = _mali_osk_calloc(1, sizeof(struct mali_dma_buf_attachment));
+	if (NULL == dma_mem) {
+		goto failed_alloc_mem;
+	}
+
+	dma_mem->buf = buf;
+	dma_mem->session = session;
+#if (!defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)) && (defined(CONFIG_MALI_DMA_BUF_LAZY_MAP))
+	dma_mem->map_ref = 1;
+#else
+	dma_mem->map_ref = 0;
+#endif
+	init_waitqueue_head(&dma_mem->wait_queue);
+
+	dma_mem->attachment = dma_buf_attach(dma_mem->buf, &mali_platform_device->dev);
+	if (NULL == dma_mem->attachment) {
+		goto failed_dma_attach;
+	}
+
+	mem_backend->dma_buf.attachment = dma_mem;
+
+	alloc->flags |= MALI_MEM_FLAG_DONT_CPU_MAP;
+	if (flags & _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE) {
+		alloc->flags |= MALI_MEM_FLAG_MALI_GUARD_PAGE;
+	}
+
+
+#if defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+	/* Map memory into session's Mali virtual address space. */
+	if (0 != mali_dma_buf_map(mem_backend)) {
+		goto Failed_dma_map;
+	}
+#endif
+
+	return _MALI_OSK_ERR_OK;
+
+#if defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+Failed_dma_map:
+	mali_dma_buf_unmap(alloc, dma_mem);
+#endif
+	/* Wait for buffer to become unmapped */
+	wait_event(dma_mem->wait_queue, !dma_mem->is_mapped);
+	MALI_DEBUG_ASSERT(!dma_mem->is_mapped);
+	dma_buf_detach(dma_mem->buf, dma_mem->attachment);
+failed_dma_attach:
+	_mali_osk_free(dma_mem);
+failed_alloc_mem:
+	dma_buf_put(buf);
+	return _MALI_OSK_ERR_FAULT;
+}
+
+void mali_mem_unbind_dma_buf(mali_mem_backend *mem_backend)
+{
+	struct mali_dma_buf_attachment *mem;
+	struct  mali_session_data *session;
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_ASSERT(MALI_MEM_DMA_BUF == mem_backend->type);
+
+	mem = mem_backend->dma_buf.attachment;
+
+	MALI_DEBUG_ASSERT_POINTER(mem);
+	MALI_DEBUG_ASSERT_POINTER(mem->attachment);
+	MALI_DEBUG_ASSERT_POINTER(mem->buf);
+	MALI_DEBUG_PRINT(3, ("Mali DMA-buf: release attachment %p\n", mem));
+
+	MALI_DEBUG_ASSERT_POINTER(mem_backend->mali_allocation);
+	session = mem_backend->mali_allocation->session;
+
+#if (defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)) ||((!defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)) && (defined(CONFIG_MALI_DMA_BUF_LAZY_MAP)))
+	/* We mapped implicitly on attach, so we need to unmap on release */
+	mali_dma_buf_unmap(mem_backend->mali_allocation, mem);
+#endif
+	/* Wait for buffer to become unmapped */
+	wait_event(mem->wait_queue, !mem->is_mapped);
+	MALI_DEBUG_ASSERT(!mem->is_mapped);
+
+	dma_buf_detach(mem->buf, mem->attachment);
+	dma_buf_put(mem->buf);
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	mali_session_memory_lock(session);
+	_mali_osk_free(mem);
+	mali_session_memory_unlock(session);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_dma_buf.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_dma_buf.h
@@ -0,0 +1,53 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_DMA_BUF_H__
+#define __MALI_MEMORY_DMA_BUF_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "mali_uk_types.h"
+#include "mali_osk.h"
+#include "mali_memory.h"
+
+struct mali_pp_job;
+
+struct mali_dma_buf_attachment;
+struct mali_dma_buf_attachment {
+	struct dma_buf *buf;
+	struct dma_buf_attachment *attachment;
+	struct sg_table *sgt;
+	struct mali_session_data *session;
+	int map_ref;
+	struct mutex map_lock;
+	mali_bool is_mapped;
+	wait_queue_head_t wait_queue;
+};
+
+int mali_dma_buf_get_size(struct mali_session_data *session, _mali_uk_dma_buf_get_size_s __user *arg);
+
+void mali_mem_unbind_dma_buf(mali_mem_backend *mem_backend);
+
+_mali_osk_errcode_t mali_mem_bind_dma_buf(mali_mem_allocation *alloc,
+		mali_mem_backend *mem_backend,
+		int fd, u32 flags);
+
+#if !defined(CONFIG_MALI_DMA_BUF_MAP_ON_ATTACH)
+int mali_dma_buf_map_job(struct mali_pp_job *job);
+void mali_dma_buf_unmap_job(struct mali_pp_job *job);
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_MEMORY_DMA_BUF_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_external.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_external.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2013-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_ukk.h"
+#include "mali_memory.h"
+#include "mali_mem_validation.h"
+#include "mali_uk_types.h"
+
+void mali_mem_unbind_ext_buf(mali_mem_backend *mem_backend)
+{
+	mali_mem_allocation *alloc;
+	struct mali_session_data *session;
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	alloc = mem_backend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	MALI_DEBUG_ASSERT(MALI_MEM_EXTERNAL == mem_backend->type);
+
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+	mali_session_memory_lock(session);
+	mali_mem_mali_map_free(session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+			       alloc->flags);
+	mali_session_memory_unlock(session);
+}
+
+_mali_osk_errcode_t mali_mem_bind_ext_buf(mali_mem_allocation *alloc,
+		mali_mem_backend *mem_backend,
+		u32 phys_addr,
+		u32 flag)
+{
+	struct mali_session_data *session;
+	_mali_osk_errcode_t err;
+	u32 virt, phys, size;
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	size = alloc->psize;
+	session = (struct mali_session_data *)(uintptr_t)alloc->session;
+	MALI_CHECK_NON_NULL(session, _MALI_OSK_ERR_INVALID_ARGS);
+
+	/* check arguments */
+	/* NULL might be a valid Mali address */
+	if (!size) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+
+	/* size must be a multiple of the system page size */
+	if (size % _MALI_OSK_MALI_PAGE_SIZE) MALI_ERROR(_MALI_OSK_ERR_INVALID_ARGS);
+
+	/* Validate the mali physical range */
+	if (_MALI_OSK_ERR_OK != mali_mem_validation_check(phys_addr, size)) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	if (flag & _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE) {
+		alloc->flags |= MALI_MEM_FLAG_MALI_GUARD_PAGE;
+	}
+
+	mali_session_memory_lock(session);
+
+	virt = alloc->mali_vma_node.vm_node.start;
+	phys = phys_addr;
+
+	err = mali_mem_mali_map_prepare(alloc);
+	if (_MALI_OSK_ERR_OK != err) {
+		mali_session_memory_unlock(session);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	mali_mmu_pagedir_update(session->page_directory, virt, phys, size, MALI_MMU_FLAGS_DEFAULT);
+
+	if (alloc->flags & MALI_MEM_FLAG_MALI_GUARD_PAGE) {
+		mali_mmu_pagedir_update(session->page_directory, virt + size, phys, _MALI_OSK_MALI_PAGE_SIZE, MALI_MMU_FLAGS_DEFAULT);
+	}
+	MALI_DEBUG_PRINT(3,
+			 ("Requested to map physical memory 0x%x-0x%x into virtual memory 0x%x\n",
+			  phys_addr, (phys_addr + size - 1),
+			  virt));
+	mali_session_memory_unlock(session);
+
+	MALI_SUCCESS;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_external.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_external.h
@@ -0,0 +1,29 @@
+
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_EXTERNAL_H__
+#define __MALI_MEMORY_EXTERNAL_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+_mali_osk_errcode_t mali_mem_bind_ext_buf(mali_mem_allocation *alloc,
+		mali_mem_backend *mem_backend,
+		u32 phys_addr,
+		u32 flag);
+void mali_mem_unbind_ext_buf(mali_mem_backend *mem_backend);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_manager.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_manager.c
@@ -0,0 +1,1020 @@
+/*
+ * Copyright (C) 2013-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/slab.h>
+#include <linux/version.h>
+#include <linux/sched.h>
+
+#include <linux/platform_device.h>
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+#include <linux/dma-buf.h>
+#endif
+#include <linux/idr.h>
+
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_kernel_linux.h"
+#include "mali_scheduler.h"
+#include "mali_memory.h"
+#include "mali_memory_os_alloc.h"
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+#include "mali_memory_dma_buf.h"
+#include "mali_memory_secure.h"
+#endif
+#if defined(CONFIG_MALI400_UMP)
+#include "mali_memory_ump.h"
+#endif
+#include "mali_memory_manager.h"
+#include "mali_memory_virtual.h"
+#include "mali_memory_util.h"
+#include "mali_memory_external.h"
+#include "mali_memory_cow.h"
+#include "mali_memory_block_alloc.h"
+#include "mali_ukk.h"
+#include "mali_memory_swap_alloc.h"
+
+/*
+* New memory system interface
+*/
+
+/*inti idr for backend memory */
+struct idr mali_backend_idr;
+struct mutex mali_idr_mutex;
+
+/* init allocation manager */
+int mali_memory_manager_init(struct mali_allocation_manager *mgr)
+{
+	/* init Locks */
+	rwlock_init(&mgr->vm_lock);
+	mutex_init(&mgr->list_mutex);
+
+	/* init link */
+	INIT_LIST_HEAD(&mgr->head);
+
+	/* init RB tree */
+	mgr->allocation_mgr_rb = RB_ROOT;
+	mgr->mali_allocation_num = 0;
+	return 0;
+}
+
+/* Deinit allocation manager
+* Do some check for debug
+*/
+void mali_memory_manager_uninit(struct mali_allocation_manager *mgr)
+{
+	/* check RB tree is empty */
+	MALI_DEBUG_ASSERT(((void *)(mgr->allocation_mgr_rb.rb_node) == (void *)rb_last(&mgr->allocation_mgr_rb)));
+	/* check allocation List */
+	MALI_DEBUG_ASSERT(list_empty(&mgr->head));
+}
+
+/* Prepare memory descriptor */
+static mali_mem_allocation *mali_mem_allocation_struct_create(struct mali_session_data *session)
+{
+	mali_mem_allocation *mali_allocation;
+
+	/* Allocate memory */
+	mali_allocation = (mali_mem_allocation *)kzalloc(sizeof(mali_mem_allocation), GFP_KERNEL);
+	if (NULL == mali_allocation) {
+		MALI_DEBUG_PRINT(1, ("mali_mem_allocation_struct_create: descriptor was NULL\n"));
+		return NULL;
+	}
+
+	MALI_DEBUG_CODE(mali_allocation->magic = MALI_MEM_ALLOCATION_VALID_MAGIC);
+
+	/* do init */
+	mali_allocation->flags = 0;
+	mali_allocation->session = session;
+
+	INIT_LIST_HEAD(&mali_allocation->list);
+	_mali_osk_atomic_init(&mali_allocation->mem_alloc_refcount, 1);
+
+	/**
+	*add to session list
+	*/
+	mutex_lock(&session->allocation_mgr.list_mutex);
+	list_add_tail(&mali_allocation->list, &session->allocation_mgr.head);
+	session->allocation_mgr.mali_allocation_num++;
+	mutex_unlock(&session->allocation_mgr.list_mutex);
+
+	return mali_allocation;
+}
+
+void  mali_mem_allocation_struct_destory(mali_mem_allocation *alloc)
+{
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	MALI_DEBUG_ASSERT_POINTER(alloc->session);
+	mutex_lock(&alloc->session->allocation_mgr.list_mutex);
+	list_del(&alloc->list);
+	alloc->session->allocation_mgr.mali_allocation_num--;
+	mutex_unlock(&alloc->session->allocation_mgr.list_mutex);
+
+	kfree(alloc);
+}
+
+int mali_mem_backend_struct_create(mali_mem_backend **backend, u32 psize)
+{
+	mali_mem_backend *mem_backend = NULL;
+	s32 ret = -ENOSPC;
+	s32 index = -1;
+	*backend = (mali_mem_backend *)kzalloc(sizeof(mali_mem_backend), GFP_KERNEL);
+	if (NULL == *backend) {
+		MALI_DEBUG_PRINT(1, ("mali_mem_backend_struct_create: backend descriptor was NULL\n"));
+		return -1;
+	}
+	mem_backend = *backend;
+	mem_backend->size = psize;
+	mutex_init(&mem_backend->mutex);
+	INIT_LIST_HEAD(&mem_backend->list);
+	mem_backend->using_count = 0;
+
+
+	/* link backend with id */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 9, 0)
+again:
+	if (!idr_pre_get(&mali_backend_idr, GFP_KERNEL)) {
+		kfree(mem_backend);
+		return -ENOMEM;
+	}
+	mutex_lock(&mali_idr_mutex);
+	ret = idr_get_new_above(&mali_backend_idr, mem_backend, 1, &index);
+	mutex_unlock(&mali_idr_mutex);
+
+	if (-ENOSPC == ret) {
+		kfree(mem_backend);
+		return -ENOSPC;
+	}
+	if (-EAGAIN == ret)
+		goto again;
+#else
+	mutex_lock(&mali_idr_mutex);
+	ret = idr_alloc(&mali_backend_idr, mem_backend, 1, MALI_S32_MAX, GFP_KERNEL);
+	mutex_unlock(&mali_idr_mutex);
+	index = ret;
+	if (ret < 0) {
+		MALI_DEBUG_PRINT(1, ("mali_mem_backend_struct_create: Can't allocate idr for backend! \n"));
+		kfree(mem_backend);
+		return -ENOSPC;
+	}
+#endif
+	return index;
+}
+
+
+static void mali_mem_backend_struct_destory(mali_mem_backend **backend, s32 backend_handle)
+{
+	mali_mem_backend *mem_backend = *backend;
+
+	mutex_lock(&mali_idr_mutex);
+	idr_remove(&mali_backend_idr, backend_handle);
+	mutex_unlock(&mali_idr_mutex);
+	kfree(mem_backend);
+	*backend = NULL;
+}
+
+mali_mem_backend *mali_mem_backend_struct_search(struct mali_session_data *session, u32 mali_address)
+{
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+	mali_mem_allocation *mali_alloc = NULL;
+	MALI_DEBUG_ASSERT_POINTER(session);
+	mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_address, 0);
+	if (NULL == mali_vma_node)  {
+		MALI_DEBUG_PRINT(1, ("mali_mem_backend_struct_search:vma node was NULL\n"));
+		return NULL;
+	}
+	mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+	/* Get backend memory & Map on CPU */
+	mutex_lock(&mali_idr_mutex);
+	mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle);
+	mutex_unlock(&mali_idr_mutex);
+	MALI_DEBUG_ASSERT(NULL != mem_bkend);
+	return mem_bkend;
+}
+
+static _mali_osk_errcode_t mali_mem_resize(struct mali_session_data *session, mali_mem_backend *mem_backend, u32 physical_size)
+{
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+	int retval = 0;
+	mali_mem_allocation *mali_allocation = NULL;
+	mali_mem_os_mem tmp_os_mem;
+	s32 change_page_count;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_PRINT(4, (" mali_mem_resize_memory called! \n"));
+	MALI_DEBUG_ASSERT(0 == physical_size %  MALI_MMU_PAGE_SIZE);
+
+	mali_allocation = mem_backend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(mali_allocation);
+
+	MALI_DEBUG_ASSERT(MALI_MEM_FLAG_CAN_RESIZE & mali_allocation->flags);
+	MALI_DEBUG_ASSERT(MALI_MEM_OS == mali_allocation->type);
+
+	mutex_lock(&mem_backend->mutex);
+
+	/* Do resize*/
+	if (physical_size > mem_backend->size) {
+		u32 add_size = physical_size - mem_backend->size;
+
+		MALI_DEBUG_ASSERT(0 == add_size %  MALI_MMU_PAGE_SIZE);
+
+		/* Allocate new pages from os mem */
+		retval = mali_mem_os_alloc_pages(&tmp_os_mem, add_size);
+
+		if (retval) {
+			if (-ENOMEM == retval) {
+				ret = _MALI_OSK_ERR_NOMEM;
+			} else {
+				ret = _MALI_OSK_ERR_FAULT;
+			}
+			MALI_DEBUG_PRINT(2, ("_mali_ukk_mem_resize: memory allocation failed !\n"));
+			goto failed_alloc_memory;
+		}
+
+		MALI_DEBUG_ASSERT(tmp_os_mem.count == add_size / MALI_MMU_PAGE_SIZE);
+
+		/* Resize the memory of the backend */
+		ret = mali_mem_os_resize_pages(&tmp_os_mem, &mem_backend->os_mem, 0, tmp_os_mem.count);
+
+		if (ret) {
+			MALI_DEBUG_PRINT(2, ("_mali_ukk_mem_resize: memory	resizing failed !\n"));
+			goto failed_resize_pages;
+		}
+
+		/*Resize cpu mapping */
+		if (NULL != mali_allocation->cpu_mapping.vma) {
+			ret = mali_mem_os_resize_cpu_map_locked(mem_backend, mali_allocation->cpu_mapping.vma, mali_allocation->cpu_mapping.vma->vm_start  + mem_backend->size, add_size);
+			if (unlikely(ret != _MALI_OSK_ERR_OK)) {
+				MALI_DEBUG_PRINT(2, ("_mali_ukk_mem_resize: cpu mapping failed !\n"));
+				goto  failed_cpu_map;
+			}
+		}
+
+		/* Resize mali mapping */
+		_mali_osk_mutex_wait(session->memory_lock);
+		ret = mali_mem_mali_map_resize(mali_allocation, physical_size);
+
+		if (ret) {
+			MALI_DEBUG_PRINT(1, ("_mali_ukk_mem_resize: mali map resize fail !\n"));
+			goto failed_gpu_map;
+		}
+
+		ret = mali_mem_os_mali_map(&mem_backend->os_mem, session, mali_allocation->mali_vma_node.vm_node.start,
+					   mali_allocation->psize / MALI_MMU_PAGE_SIZE, add_size / MALI_MMU_PAGE_SIZE, mali_allocation->mali_mapping.properties);
+		if (ret) {
+			MALI_DEBUG_PRINT(2, ("_mali_ukk_mem_resize: mali mapping failed !\n"));
+			goto failed_gpu_map;
+		}
+
+		_mali_osk_mutex_signal(session->memory_lock);
+	} else {
+		u32 dec_size, page_count;
+		u32 vaddr = 0;
+		INIT_LIST_HEAD(&tmp_os_mem.pages);
+		tmp_os_mem.count = 0;
+
+		dec_size = mem_backend->size - physical_size;
+		MALI_DEBUG_ASSERT(0 == dec_size %  MALI_MMU_PAGE_SIZE);
+
+		page_count = dec_size / MALI_MMU_PAGE_SIZE;
+		vaddr = mali_allocation->mali_vma_node.vm_node.start + physical_size;
+
+		/* Resize the memory of the backend */
+		ret = mali_mem_os_resize_pages(&mem_backend->os_mem, &tmp_os_mem, physical_size / MALI_MMU_PAGE_SIZE, page_count);
+
+		if (ret) {
+			MALI_DEBUG_PRINT(4, ("_mali_ukk_mem_resize: mali map resize failed!\n"));
+			goto failed_resize_pages;
+		}
+
+		/* Resize mali map */
+		_mali_osk_mutex_wait(session->memory_lock);
+		mali_mem_mali_map_free(session, dec_size, vaddr, mali_allocation->flags);
+		_mali_osk_mutex_signal(session->memory_lock);
+
+		/* Zap cpu mapping */
+		if (0 != mali_allocation->cpu_mapping.addr) {
+			MALI_DEBUG_ASSERT(NULL != mali_allocation->cpu_mapping.vma);
+			zap_vma_ptes(mali_allocation->cpu_mapping.vma, mali_allocation->cpu_mapping.vma->vm_start + physical_size, dec_size);
+		}
+
+		/* Free those extra pages */
+		mali_mem_os_free(&tmp_os_mem.pages, tmp_os_mem.count, MALI_FALSE);
+	}
+
+	/* Resize memory allocation and memory backend */
+	change_page_count = (s32)(physical_size - mem_backend->size) / MALI_MMU_PAGE_SIZE;
+	mali_allocation->psize = physical_size;
+	mem_backend->size = physical_size;
+	mutex_unlock(&mem_backend->mutex);
+
+	if (change_page_count > 0) {
+		atomic_add(change_page_count, &session->mali_mem_allocated_pages);
+		if (atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > session->max_mali_mem_allocated_size) {
+			session->max_mali_mem_allocated_size = atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+		}
+
+	} else {
+		atomic_sub((s32)(-change_page_count), &session->mali_mem_allocated_pages);
+	}
+
+	return _MALI_OSK_ERR_OK;
+
+failed_gpu_map:
+	_mali_osk_mutex_signal(session->memory_lock);
+failed_cpu_map:
+	if (physical_size > mem_backend->size) {
+		mali_mem_os_resize_pages(&mem_backend->os_mem, &tmp_os_mem, mem_backend->size / MALI_MMU_PAGE_SIZE,
+					 (physical_size - mem_backend->size) / MALI_MMU_PAGE_SIZE);
+	} else {
+		mali_mem_os_resize_pages(&tmp_os_mem, &mem_backend->os_mem, 0, tmp_os_mem.count);
+	}
+failed_resize_pages:
+	if (0 != tmp_os_mem.count)
+		mali_mem_os_free(&tmp_os_mem.pages, tmp_os_mem.count, MALI_FALSE);
+failed_alloc_memory:
+
+	mutex_unlock(&mem_backend->mutex);
+	return ret;
+}
+
+
+/* Set GPU MMU properties */
+static void _mali_memory_gpu_map_property_set(u32 *properties, u32 flags)
+{
+	if (_MALI_MEMORY_GPU_READ_ALLOCATE & flags) {
+		*properties = MALI_MMU_FLAGS_FORCE_GP_READ_ALLOCATE;
+	} else {
+		*properties = MALI_MMU_FLAGS_DEFAULT;
+	}
+}
+
+_mali_osk_errcode_t mali_mem_add_mem_size(struct mali_session_data *session, u32 mali_addr, u32 add_size)
+{
+	mali_mem_backend *mem_backend = NULL;
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+	mali_mem_allocation *mali_allocation = NULL;
+	u32 new_physical_size;
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT(0 == add_size %  MALI_MMU_PAGE_SIZE);
+
+	/* Get the memory backend that need to be resize. */
+	mem_backend = mali_mem_backend_struct_search(session, mali_addr);
+
+	if (NULL == mem_backend)  {
+		MALI_DEBUG_PRINT(2, ("_mali_ukk_mem_resize: memory backend = NULL!\n"));
+		return ret;
+	}
+
+	mali_allocation = mem_backend->mali_allocation;
+
+	MALI_DEBUG_ASSERT_POINTER(mali_allocation);
+
+	new_physical_size = add_size + mem_backend->size;
+
+	if (new_physical_size > (mali_allocation->mali_vma_node.vm_node.size))
+		return ret;
+
+	MALI_DEBUG_ASSERT(new_physical_size != mem_backend->size);
+
+	ret = mali_mem_resize(session, mem_backend, new_physical_size);
+
+	return ret;
+}
+
+/**
+*  function@_mali_ukk_mem_allocate - allocate mali memory
+*/
+_mali_osk_errcode_t _mali_ukk_mem_allocate(_mali_uk_alloc_mem_s *args)
+{
+	struct mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	mali_mem_backend *mem_backend = NULL;
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+	int retval = 0;
+	mali_mem_allocation *mali_allocation = NULL;
+	struct mali_vma_node *mali_vma_node = NULL;
+
+	MALI_DEBUG_PRINT(4, (" _mali_ukk_mem_allocate, vaddr=0x%x, size =0x%x! \n", args->gpu_vaddr, args->psize));
+
+	if (args->vsize < args->psize) {
+		MALI_PRINT_ERROR(("_mali_ukk_mem_allocate: vsize %d  shouldn't be less than psize %d\n", args->vsize, args->psize));
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	} else if ((args->vsize % _MALI_OSK_MALI_PAGE_SIZE) || (args->psize % _MALI_OSK_MALI_PAGE_SIZE)) {
+		MALI_PRINT_ERROR(("_mali_ukk_mem_allocate: not supported non page aligned size-->pszie %d, vsize %d\n",  args->psize, args->vsize));
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	} else if ((args->vsize != args->psize) && ((args->flags & _MALI_MEMORY_ALLOCATE_SWAPPABLE) || (args->flags & _MALI_MEMORY_ALLOCATE_SECURE))) {
+		MALI_PRINT_ERROR(("_mali_ukk_mem_allocate: not supported mem resizeable for mem flag %d\n",  args->flags));
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	}
+
+	/* Check if the address is allocated
+	*/
+	mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, args->gpu_vaddr, 0);
+
+	if (unlikely(mali_vma_node)) {
+		MALI_DEBUG_PRINT_ERROR(("The mali virtual address has already been used ! \n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+	/**
+	*create mali memory allocation
+	*/
+
+	mali_allocation = mali_mem_allocation_struct_create(session);
+
+	if (mali_allocation == NULL) {
+		MALI_DEBUG_PRINT(1, ("_mali_ukk_mem_allocate: Failed to create allocation struct! \n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+	mali_allocation->psize = args->psize;
+	mali_allocation->vsize = args->vsize;
+
+	/* MALI_MEM_OS if need to support mem resize,
+	 * or MALI_MEM_BLOCK if have dedicated memory,
+	 * or MALI_MEM_OS,
+	 * or MALI_MEM_SWAP.
+	 */
+	if (args->flags & _MALI_MEMORY_ALLOCATE_SWAPPABLE) {
+		mali_allocation->type = MALI_MEM_SWAP;
+	} else if (args->flags & _MALI_MEMORY_ALLOCATE_RESIZEABLE) {
+		mali_allocation->type = MALI_MEM_OS;
+		mali_allocation->flags |= MALI_MEM_FLAG_CAN_RESIZE;
+	} else if (args->flags & _MALI_MEMORY_ALLOCATE_SECURE) {
+		mali_allocation->type = MALI_MEM_SECURE;
+	} else if (MALI_TRUE == mali_memory_have_dedicated_memory()) {
+		mali_allocation->type = MALI_MEM_BLOCK;
+	} else {
+		mali_allocation->type = MALI_MEM_OS;
+	}
+
+	/**
+	*add allocation node to RB tree for index
+	*/
+	mali_allocation->mali_vma_node.vm_node.start = args->gpu_vaddr;
+	mali_allocation->mali_vma_node.vm_node.size = args->vsize;
+
+	mali_vma_offset_add(&session->allocation_mgr, &mali_allocation->mali_vma_node);
+
+	mali_allocation->backend_handle = mali_mem_backend_struct_create(&mem_backend, args->psize);
+	if (mali_allocation->backend_handle < 0) {
+		ret = _MALI_OSK_ERR_NOMEM;
+		MALI_DEBUG_PRINT(1, ("mali_allocation->backend_handle < 0! \n"));
+		goto failed_alloc_backend;
+	}
+
+
+	mem_backend->mali_allocation = mali_allocation;
+	mem_backend->type = mali_allocation->type;
+
+	mali_allocation->mali_mapping.addr = args->gpu_vaddr;
+
+	/* set gpu mmu propery */
+	_mali_memory_gpu_map_property_set(&mali_allocation->mali_mapping.properties, args->flags);
+	/* do prepare for MALI mapping */
+	if (!(args->flags & _MALI_MEMORY_ALLOCATE_NO_BIND_GPU) && mali_allocation->psize > 0) {
+		_mali_osk_mutex_wait(session->memory_lock);
+
+		ret = mali_mem_mali_map_prepare(mali_allocation);
+		if (0 != ret) {
+			_mali_osk_mutex_signal(session->memory_lock);
+			goto failed_prepare_map;
+		}
+		_mali_osk_mutex_signal(session->memory_lock);
+	}
+
+	if (mali_allocation->psize == 0) {
+		mem_backend->os_mem.count = 0;
+		INIT_LIST_HEAD(&mem_backend->os_mem.pages);
+		goto done;
+	}
+
+	if (args->flags & _MALI_MEMORY_ALLOCATE_DEFER_BIND) {
+		mali_allocation->flags |= _MALI_MEMORY_ALLOCATE_DEFER_BIND;
+		mem_backend->flags |= MALI_MEM_BACKEND_FLAG_NOT_BINDED;
+		/* init for defer bind backend*/
+		mem_backend->os_mem.count = 0;
+		INIT_LIST_HEAD(&mem_backend->os_mem.pages);
+
+		goto done;
+	}
+
+	if (likely(mali_allocation->psize > 0)) {
+
+		if (MALI_MEM_SECURE == mem_backend->type) {
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+			ret = mali_mem_secure_attach_dma_buf(&mem_backend->secure_mem, mem_backend->size, args->secure_shared_fd);
+			if (_MALI_OSK_ERR_OK != ret) {
+				MALI_DEBUG_PRINT(1, ("Failed to attach dma buf for secure memory! \n"));
+				goto failed_alloc_pages;
+			}
+#else
+			ret = _MALI_OSK_ERR_UNSUPPORTED;
+			MALI_DEBUG_PRINT(1, ("DMA not supported for mali secure memory! \n"));
+			goto failed_alloc_pages;
+#endif
+		} else {
+
+			/**
+			*allocate physical memory
+			*/
+			if (mem_backend->type == MALI_MEM_OS) {
+				retval = mali_mem_os_alloc_pages(&mem_backend->os_mem, mem_backend->size);
+			} else if (mem_backend->type == MALI_MEM_BLOCK) {
+				/* try to allocated from BLOCK memory first, then try OS memory if failed.*/
+				if (mali_mem_block_alloc(&mem_backend->block_mem, mem_backend->size)) {
+					retval = mali_mem_os_alloc_pages(&mem_backend->os_mem, mem_backend->size);
+					mem_backend->type = MALI_MEM_OS;
+					mali_allocation->type = MALI_MEM_OS;
+				}
+			} else if (MALI_MEM_SWAP == mem_backend->type) {
+				retval = mali_mem_swap_alloc_pages(&mem_backend->swap_mem, mali_allocation->mali_vma_node.vm_node.size, &mem_backend->start_idx);
+			}  else {
+				/* ONLY support mem_os type */
+				MALI_DEBUG_ASSERT(0);
+			}
+
+			if (retval) {
+				ret = _MALI_OSK_ERR_NOMEM;
+				MALI_DEBUG_PRINT(1, (" can't allocate enough pages! \n"));
+				goto failed_alloc_pages;
+			}
+		}
+	}
+
+	/**
+	*map to GPU side
+	*/
+	if (!(args->flags & _MALI_MEMORY_ALLOCATE_NO_BIND_GPU) && mali_allocation->psize > 0) {
+		_mali_osk_mutex_wait(session->memory_lock);
+		/* Map on Mali */
+
+		if (mem_backend->type == MALI_MEM_OS) {
+			ret = mali_mem_os_mali_map(&mem_backend->os_mem, session, args->gpu_vaddr, 0,
+						   mem_backend->size / MALI_MMU_PAGE_SIZE, mali_allocation->mali_mapping.properties);
+
+		} else if (mem_backend->type == MALI_MEM_BLOCK) {
+			mali_mem_block_mali_map(&mem_backend->block_mem, session, args->gpu_vaddr,
+						mali_allocation->mali_mapping.properties);
+		} else if (mem_backend->type == MALI_MEM_SWAP) {
+			ret = mali_mem_swap_mali_map(&mem_backend->swap_mem, session, args->gpu_vaddr,
+						     mali_allocation->mali_mapping.properties);
+		} else if (mem_backend->type == MALI_MEM_SECURE) {
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+			ret = mali_mem_secure_mali_map(&mem_backend->secure_mem, session, args->gpu_vaddr, mali_allocation->mali_mapping.properties);
+#endif
+		} else { /* unsupport type */
+			MALI_DEBUG_ASSERT(0);
+		}
+
+		_mali_osk_mutex_signal(session->memory_lock);
+	}
+done:
+	if (MALI_MEM_OS == mem_backend->type) {
+		atomic_add(mem_backend->os_mem.count, &session->mali_mem_allocated_pages);
+	} else if (MALI_MEM_BLOCK == mem_backend->type) {
+		atomic_add(mem_backend->block_mem.count, &session->mali_mem_allocated_pages);
+	} else if (MALI_MEM_SECURE == mem_backend->type) {
+		atomic_add(mem_backend->secure_mem.count, &session->mali_mem_allocated_pages);
+	} else {
+		MALI_DEBUG_ASSERT(MALI_MEM_SWAP == mem_backend->type);
+		atomic_add(mem_backend->swap_mem.count, &session->mali_mem_allocated_pages);
+		atomic_add(mem_backend->swap_mem.count, &session->mali_mem_array[mem_backend->type]);
+	}
+
+	if (atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > session->max_mali_mem_allocated_size) {
+		session->max_mali_mem_allocated_size = atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+	}
+	return _MALI_OSK_ERR_OK;
+
+failed_alloc_pages:
+	mali_mem_mali_map_free(session, mali_allocation->psize, mali_allocation->mali_vma_node.vm_node.start, mali_allocation->flags);
+failed_prepare_map:
+	mali_mem_backend_struct_destory(&mem_backend, mali_allocation->backend_handle);
+failed_alloc_backend:
+
+	mali_vma_offset_remove(&session->allocation_mgr, &mali_allocation->mali_vma_node);
+	mali_mem_allocation_struct_destory(mali_allocation);
+
+	return ret;
+}
+
+
+_mali_osk_errcode_t _mali_ukk_mem_free(_mali_uk_free_mem_s *args)
+{
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	u32 vaddr = args->gpu_vaddr;
+	mali_mem_allocation *mali_alloc = NULL;
+	struct mali_vma_node *mali_vma_node = NULL;
+
+	/* find mali allocation structure by vaddress*/
+	mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, vaddr, 0);
+	if (NULL == mali_vma_node) {
+		MALI_DEBUG_PRINT(1, ("_mali_ukk_mem_free: invalid addr: 0x%x\n", vaddr));
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	}
+
+	mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+
+	if (mali_alloc) {
+		if ((MALI_MEM_UMP == mali_alloc->type) || (MALI_MEM_DMA_BUF == mali_alloc->type)
+		    || (MALI_MEM_EXTERNAL == mali_alloc->type)) {
+			MALI_PRINT_ERROR(("_mali_ukk_mem_free: not supported for memory type %d\n",  mali_alloc->type));
+			return _MALI_OSK_ERR_UNSUPPORTED;
+		}
+		/* check ref_count */
+		args->free_pages_nr = mali_allocation_unref(&mali_alloc);
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+
+/**
+* Function _mali_ukk_mem_bind -- bind a external memory to a new GPU address
+* It will allocate a new mem allocation and bind external memory to it.
+* Supported backend type are:
+* _MALI_MEMORY_BIND_BACKEND_UMP
+* _MALI_MEMORY_BIND_BACKEND_DMA_BUF
+* _MALI_MEMORY_BIND_BACKEND_EXTERNAL_MEMORY
+* CPU access is not supported yet
+*/
+_mali_osk_errcode_t _mali_ukk_mem_bind(_mali_uk_bind_mem_s *args)
+{
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	mali_mem_backend *mem_backend = NULL;
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+	mali_mem_allocation *mali_allocation = NULL;
+	MALI_DEBUG_PRINT(5, (" _mali_ukk_mem_bind, vaddr=0x%x, size =0x%x! \n", args->vaddr, args->size));
+
+	/**
+	* allocate mali allocation.
+	*/
+	mali_allocation = mali_mem_allocation_struct_create(session);
+
+	if (mali_allocation == NULL) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+	mali_allocation->psize = args->size;
+	mali_allocation->vsize = args->size;
+	mali_allocation->mali_mapping.addr = args->vaddr;
+
+	/* add allocation node to RB tree for index  */
+	mali_allocation->mali_vma_node.vm_node.start = args->vaddr;
+	mali_allocation->mali_vma_node.vm_node.size = args->size;
+	mali_vma_offset_add(&session->allocation_mgr, &mali_allocation->mali_vma_node);
+
+	/* allocate backend*/
+	if (mali_allocation->psize > 0) {
+		mali_allocation->backend_handle = mali_mem_backend_struct_create(&mem_backend, mali_allocation->psize);
+		if (mali_allocation->backend_handle < 0) {
+			goto Failed_alloc_backend;
+		}
+
+	} else {
+		goto Failed_alloc_backend;
+	}
+
+	mem_backend->size = mali_allocation->psize;
+	mem_backend->mali_allocation = mali_allocation;
+
+	switch (args->flags & _MALI_MEMORY_BIND_BACKEND_MASK) {
+	case  _MALI_MEMORY_BIND_BACKEND_UMP:
+#if defined(CONFIG_MALI400_UMP)
+		mali_allocation->type = MALI_MEM_UMP;
+		mem_backend->type = MALI_MEM_UMP;
+		ret = mali_mem_bind_ump_buf(mali_allocation, mem_backend,
+					    args->mem_union.bind_ump.secure_id, args->mem_union.bind_ump.flags);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_DEBUG_PRINT(1, ("Bind ump buf failed\n"));
+			goto  Failed_bind_backend;
+		}
+#else
+		MALI_DEBUG_PRINT(1, ("UMP not supported\n"));
+		goto Failed_bind_backend;
+#endif
+		break;
+	case  _MALI_MEMORY_BIND_BACKEND_DMA_BUF:
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+		mali_allocation->type = MALI_MEM_DMA_BUF;
+		mem_backend->type = MALI_MEM_DMA_BUF;
+		ret = mali_mem_bind_dma_buf(mali_allocation, mem_backend,
+					    args->mem_union.bind_dma_buf.mem_fd, args->mem_union.bind_dma_buf.flags);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_DEBUG_PRINT(1, ("Bind dma buf failed\n"));
+			goto Failed_bind_backend;
+		}
+#else
+		MALI_DEBUG_PRINT(1, ("DMA not supported\n"));
+		goto Failed_bind_backend;
+#endif
+		break;
+	case _MALI_MEMORY_BIND_BACKEND_MALI_MEMORY:
+		/* not allowed */
+		MALI_DEBUG_PRINT_ERROR(("Mali internal memory type not supported !\n"));
+		goto Failed_bind_backend;
+		break;
+
+	case _MALI_MEMORY_BIND_BACKEND_EXTERNAL_MEMORY:
+		mali_allocation->type = MALI_MEM_EXTERNAL;
+		mem_backend->type = MALI_MEM_EXTERNAL;
+		ret = mali_mem_bind_ext_buf(mali_allocation, mem_backend, args->mem_union.bind_ext_memory.phys_addr,
+					    args->mem_union.bind_ext_memory.flags);
+		if (_MALI_OSK_ERR_OK != ret) {
+			MALI_DEBUG_PRINT(1, ("Bind external buf failed\n"));
+			goto Failed_bind_backend;
+		}
+		break;
+
+	case _MALI_MEMORY_BIND_BACKEND_EXT_COW:
+		/* not allowed */
+		MALI_DEBUG_PRINT_ERROR(("External cow memory  type not supported !\n"));
+		goto Failed_bind_backend;
+		break;
+
+	default:
+		MALI_DEBUG_PRINT_ERROR(("Invalid memory type  not supported !\n"));
+		goto Failed_bind_backend;
+		break;
+	}
+	MALI_DEBUG_ASSERT(0 == mem_backend->size % MALI_MMU_PAGE_SIZE);
+	atomic_add(mem_backend->size / MALI_MMU_PAGE_SIZE, &session->mali_mem_array[mem_backend->type]);
+	return _MALI_OSK_ERR_OK;
+
+Failed_bind_backend:
+	mali_mem_backend_struct_destory(&mem_backend, mali_allocation->backend_handle);
+
+Failed_alloc_backend:
+	mali_vma_offset_remove(&session->allocation_mgr, &mali_allocation->mali_vma_node);
+	mali_mem_allocation_struct_destory(mali_allocation);
+
+	MALI_DEBUG_PRINT(1, (" _mali_ukk_mem_bind, return ERROR! \n"));
+	return ret;
+}
+
+
+/*
+* Function _mali_ukk_mem_unbind -- unbind a external memory to a new GPU address
+* This function unbind the backend memory and free the allocation
+* no ref_count for this type of memory
+*/
+_mali_osk_errcode_t _mali_ukk_mem_unbind(_mali_uk_unbind_mem_s *args)
+{
+	/**/
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	mali_mem_allocation *mali_allocation = NULL;
+	struct mali_vma_node *mali_vma_node = NULL;
+	u32 mali_addr = args->vaddr;
+	MALI_DEBUG_PRINT(5, (" _mali_ukk_mem_unbind, vaddr=0x%x! \n", args->vaddr));
+
+	/* find the allocation by vaddr */
+	mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_addr, 0);
+	if (likely(mali_vma_node)) {
+		MALI_DEBUG_ASSERT(mali_addr == mali_vma_node->vm_node.start);
+		mali_allocation = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+	} else {
+		MALI_DEBUG_ASSERT(NULL != mali_vma_node);
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	}
+
+	if (NULL != mali_allocation) {
+
+		if ((MALI_MEM_UMP != mali_allocation->type) && (MALI_MEM_DMA_BUF != mali_allocation->type)
+		    && (MALI_MEM_EXTERNAL != mali_allocation->type)) {
+			MALI_PRINT_ERROR(("_mali_ukk_mem_unbind not supported for memory type %d\n",  mali_allocation->type));
+			return _MALI_OSK_ERR_UNSUPPORTED;
+		}
+
+		/* check ref_count */
+		mali_allocation_unref(&mali_allocation);
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+/*
+* Function _mali_ukk_mem_cow --  COW for an allocation
+* This function allocate new pages for  a range (range, range+size) of allocation
+*  And Map it(keep use the not in range pages from target allocation ) to an GPU vaddr
+*/
+_mali_osk_errcode_t _mali_ukk_mem_cow(_mali_uk_cow_mem_s *args)
+{
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+	mali_mem_backend *target_backend = NULL;
+	mali_mem_backend *mem_backend = NULL;
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_allocation *mali_allocation = NULL;
+
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	/* Get the target backend for cow */
+	target_backend = mali_mem_backend_struct_search(session, args->target_handle);
+
+	if (NULL == target_backend || 0 == target_backend->size) {
+		MALI_DEBUG_ASSERT_POINTER(target_backend);
+		MALI_DEBUG_ASSERT(0 != target_backend->size);
+		return ret;
+	}
+
+	/*Cow not support resized mem */
+	MALI_DEBUG_ASSERT(MALI_MEM_FLAG_CAN_RESIZE != (MALI_MEM_FLAG_CAN_RESIZE & target_backend->mali_allocation->flags));
+
+	/* Check if the new mali address is allocated */
+	mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, args->vaddr, 0);
+
+	if (unlikely(mali_vma_node)) {
+		MALI_DEBUG_PRINT_ERROR(("The mali virtual address has already been used ! \n"));
+		return ret;
+	}
+
+	/* create new alloction for COW*/
+	mali_allocation = mali_mem_allocation_struct_create(session);
+	if (mali_allocation == NULL) {
+		MALI_DEBUG_PRINT(1, ("_mali_ukk_mem_cow: Failed to create allocation struct!\n"));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+	mali_allocation->psize = args->target_size;
+	mali_allocation->vsize = args->target_size;
+	mali_allocation->type = MALI_MEM_COW;
+
+	/*add allocation node to RB tree for index*/
+	mali_allocation->mali_vma_node.vm_node.start = args->vaddr;
+	mali_allocation->mali_vma_node.vm_node.size = mali_allocation->vsize;
+	mali_vma_offset_add(&session->allocation_mgr, &mali_allocation->mali_vma_node);
+
+	/* create new backend for COW memory */
+	mali_allocation->backend_handle = mali_mem_backend_struct_create(&mem_backend, mali_allocation->psize);
+	if (mali_allocation->backend_handle < 0) {
+		ret = _MALI_OSK_ERR_NOMEM;
+		MALI_DEBUG_PRINT(1, ("mali_allocation->backend_handle < 0! \n"));
+		goto failed_alloc_backend;
+	}
+	mem_backend->mali_allocation = mali_allocation;
+	mem_backend->type = mali_allocation->type;
+
+	if (target_backend->type == MALI_MEM_SWAP ||
+	    (MALI_MEM_COW == target_backend->type && (MALI_MEM_BACKEND_FLAG_SWAP_COWED & target_backend->flags))) {
+		mem_backend->flags |= MALI_MEM_BACKEND_FLAG_SWAP_COWED;
+		/**
+		 *     CoWed swap backends couldn't be mapped as non-linear vma, because if one
+		 * vma is set with flag VM_NONLINEAR, the vma->vm_private_data will be used by kernel,
+		 * while in mali driver, we use this variable to store the pointer of mali_allocation, so there
+		 * is a conflict.
+		 *     To resolve this problem, we have to do some fake things, we reserved about 64MB
+		 * space from index 0, there isn't really page's index will be set from 0 to (64MB>>PAGE_SHIFT_NUM),
+		 * and all of CoWed swap memory backends' start_idx will be assigned with 0, and these
+		 * backends will be mapped as linear and will add to priority tree of global swap file, while
+		 * these vmas will never be found by using normal page->index, these pages in those vma
+		 * also couldn't be swapped out.
+		 */
+		mem_backend->start_idx = 0;
+	}
+
+	/* Add the target backend's cow count, also allocate new pages for COW backend from os mem
+	*for a modified range and keep the page which not in the modified range and Add ref to it
+	*/
+	MALI_DEBUG_PRINT(3, ("Cow mapping: target_addr: 0x%x;  cow_addr: 0x%x,  size: %u\n", target_backend->mali_allocation->mali_vma_node.vm_node.start,
+			     mali_allocation->mali_vma_node.vm_node.start, mali_allocation->mali_vma_node.vm_node.size));
+
+	ret = mali_memory_do_cow(target_backend, args->target_offset, args->target_size, mem_backend, args->range_start, args->range_size);
+	if (_MALI_OSK_ERR_OK != ret) {
+		MALI_DEBUG_PRINT(1, ("_mali_ukk_mem_cow: Failed to cow!\n"));
+		goto failed_do_cow;
+	}
+
+	/**
+	*map to GPU side
+	*/
+	mali_allocation->mali_mapping.addr = args->vaddr;
+	/* set gpu mmu propery */
+	_mali_memory_gpu_map_property_set(&mali_allocation->mali_mapping.properties, args->flags);
+
+	_mali_osk_mutex_wait(session->memory_lock);
+	/* Map on Mali */
+	ret = mali_mem_mali_map_prepare(mali_allocation);
+	if (0 != ret) {
+		MALI_DEBUG_PRINT(1, (" prepare map fail! \n"));
+		goto failed_gpu_map;
+	}
+
+	if (!(mem_backend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED)) {
+		mali_mem_cow_mali_map(mem_backend, 0, mem_backend->size);
+	}
+
+	_mali_osk_mutex_signal(session->memory_lock);
+
+	mutex_lock(&target_backend->mutex);
+	target_backend->flags |= MALI_MEM_BACKEND_FLAG_COWED;
+	mutex_unlock(&target_backend->mutex);
+
+	atomic_add(args->range_size / MALI_MMU_PAGE_SIZE, &session->mali_mem_allocated_pages);
+	if (atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > session->max_mali_mem_allocated_size) {
+		session->max_mali_mem_allocated_size = atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+	}
+	return _MALI_OSK_ERR_OK;
+
+failed_gpu_map:
+	_mali_osk_mutex_signal(session->memory_lock);
+	mali_mem_cow_release(mem_backend, MALI_FALSE);
+	mem_backend->cow_mem.count = 0;
+failed_do_cow:
+	mali_mem_backend_struct_destory(&mem_backend, mali_allocation->backend_handle);
+failed_alloc_backend:
+	mali_vma_offset_remove(&session->allocation_mgr, &mali_allocation->mali_vma_node);
+	mali_mem_allocation_struct_destory(mali_allocation);
+
+	return ret;
+}
+
+_mali_osk_errcode_t _mali_ukk_mem_cow_modify_range(_mali_uk_cow_modify_range_s *args)
+{
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+	mali_mem_backend *mem_backend = NULL;
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+
+	MALI_DEBUG_PRINT(4, (" _mali_ukk_mem_cow_modify_range called! \n"));
+	/* Get the backend that need to be modified. */
+	mem_backend = mali_mem_backend_struct_search(session, args->vaddr);
+
+	if (NULL == mem_backend || 0 == mem_backend->size) {
+		MALI_DEBUG_ASSERT_POINTER(mem_backend);
+		MALI_DEBUG_ASSERT(0 != mem_backend->size);
+		return ret;
+	}
+
+	if (MALI_MEM_COW  != mem_backend->type) {
+		MALI_PRINT_ERROR(("_mali_ukk_mem_cow_modify_range: not supported for memory type %d !\n", mem_backend->type));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	ret =  mali_memory_cow_modify_range(mem_backend, args->range_start, args->size);
+	args->change_pages_nr = mem_backend->cow_mem.change_pages_nr;
+	if (_MALI_OSK_ERR_OK != ret)
+		return  ret;
+	_mali_osk_mutex_wait(session->memory_lock);
+	if (!(mem_backend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED)) {
+		mali_mem_cow_mali_map(mem_backend, args->range_start, args->size);
+	}
+	_mali_osk_mutex_signal(session->memory_lock);
+
+	atomic_add(args->change_pages_nr, &session->mali_mem_allocated_pages);
+	if (atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > session->max_mali_mem_allocated_size) {
+		session->max_mali_mem_allocated_size = atomic_read(&session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+
+_mali_osk_errcode_t _mali_ukk_mem_resize(_mali_uk_mem_resize_s *args)
+{
+	mali_mem_backend *mem_backend = NULL;
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_FAULT;
+
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_PRINT(4, (" mali_mem_resize_memory called! \n"));
+	MALI_DEBUG_ASSERT(0 == args->psize %  MALI_MMU_PAGE_SIZE);
+
+	/* Get the memory backend that need to be resize. */
+	mem_backend = mali_mem_backend_struct_search(session, args->vaddr);
+
+	if (NULL == mem_backend)  {
+		MALI_DEBUG_PRINT(2, ("_mali_ukk_mem_resize: memory backend = NULL!\n"));
+		return ret;
+	}
+
+	MALI_DEBUG_ASSERT(args->psize != mem_backend->size);
+
+	ret = mali_mem_resize(session, mem_backend, args->psize);
+
+	return ret;
+}
+
+_mali_osk_errcode_t _mali_ukk_mem_usage_get(_mali_uk_profiling_memory_usage_get_s *args)
+{
+	args->memory_usage = _mali_ukk_report_memory_usage();
+	if (0 != args->vaddr) {
+		mali_mem_backend *mem_backend = NULL;
+		struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+		/* Get the backend that need to be modified. */
+		mem_backend = mali_mem_backend_struct_search(session, args->vaddr);
+		if (NULL == mem_backend) {
+			MALI_DEBUG_ASSERT_POINTER(mem_backend);
+			return _MALI_OSK_ERR_FAULT;
+		}
+
+		if (MALI_MEM_COW == mem_backend->type)
+			args->change_pages_nr = mem_backend->cow_mem.change_pages_nr;
+	}
+	return _MALI_OSK_ERR_OK;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_manager.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_manager.h
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_MANAGER_H__
+#define __MALI_MEMORY_MANAGER_H__
+
+#include "mali_osk.h"
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/rbtree.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include "mali_memory_types.h"
+#include "mali_memory_os_alloc.h"
+#include "mali_uk_types.h"
+
+struct mali_allocation_manager {
+	rwlock_t vm_lock;
+	struct rb_root allocation_mgr_rb;
+	struct list_head head;
+	struct mutex list_mutex;
+	u32 mali_allocation_num;
+};
+
+extern struct idr mali_backend_idr;
+extern struct mutex mali_idr_mutex;
+
+int mali_memory_manager_init(struct mali_allocation_manager *mgr);
+void mali_memory_manager_uninit(struct mali_allocation_manager *mgr);
+
+void  mali_mem_allocation_struct_destory(mali_mem_allocation *alloc);
+_mali_osk_errcode_t mali_mem_add_mem_size(struct mali_session_data *session, u32 mali_addr, u32 add_size);
+mali_mem_backend *mali_mem_backend_struct_search(struct mali_session_data *session, u32 mali_address);
+_mali_osk_errcode_t _mali_ukk_mem_allocate(_mali_uk_alloc_mem_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_free(_mali_uk_free_mem_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_bind(_mali_uk_bind_mem_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_unbind(_mali_uk_unbind_mem_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_cow(_mali_uk_cow_mem_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_cow_modify_range(_mali_uk_cow_modify_range_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_usage_get(_mali_uk_profiling_memory_usage_get_s *args);
+_mali_osk_errcode_t _mali_ukk_mem_resize(_mali_uk_mem_resize_s *args);
+
+#endif
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_os_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_os_alloc.c
@@ -0,0 +1,852 @@
+/*
+ * Copyright (C) 2013-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/version.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+
+#include "mali_osk.h"
+#include "mali_memory.h"
+#include "mali_memory_os_alloc.h"
+#include "mali_kernel_linux.h"
+
+/* Minimum size of allocator page pool */
+#define MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES (MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_MB * 256)
+#define MALI_OS_MEMORY_POOL_TRIM_JIFFIES (10 * CONFIG_HZ) /* Default to 10s */
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 8, 0)
+static unsigned long dma_attrs_wc = 0;
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0)
+/* Write combine dma_attrs */
+static DEFINE_DMA_ATTRS(dma_attrs_wc);
+#endif
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 0, 0)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 35)
+static int mali_mem_os_shrink(int nr_to_scan, gfp_t gfp_mask);
+#else
+static int mali_mem_os_shrink(struct shrinker *shrinker, int nr_to_scan, gfp_t gfp_mask);
+#endif
+#else
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 12, 0)
+static int mali_mem_os_shrink(struct shrinker *shrinker, struct shrink_control *sc);
+#else
+static unsigned long mali_mem_os_shrink(struct shrinker *shrinker, struct shrink_control *sc);
+static unsigned long mali_mem_os_shrink_count(struct shrinker *shrinker, struct shrink_control *sc);
+#endif
+#endif
+static void mali_mem_os_trim_pool(struct work_struct *work);
+
+struct mali_mem_os_allocator mali_mem_os_allocator = {
+	.pool_lock = __SPIN_LOCK_UNLOCKED(pool_lock),
+	.pool_pages = LIST_HEAD_INIT(mali_mem_os_allocator.pool_pages),
+	.pool_count = 0,
+
+	.allocated_pages = ATOMIC_INIT(0),
+	.allocation_limit = 0,
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 12, 0)
+	.shrinker.shrink = mali_mem_os_shrink,
+#else
+	.shrinker.count_objects = mali_mem_os_shrink_count,
+	.shrinker.scan_objects = mali_mem_os_shrink,
+#endif
+	.shrinker.seeks = DEFAULT_SEEKS,
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 7, 0)
+	.timed_shrinker = __DELAYED_WORK_INITIALIZER(mali_mem_os_allocator.timed_shrinker, mali_mem_os_trim_pool, TIMER_DEFERRABLE),
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 38)
+	.timed_shrinker = __DEFERRED_WORK_INITIALIZER(mali_mem_os_allocator.timed_shrinker, mali_mem_os_trim_pool),
+#else
+	.timed_shrinker = __DELAYED_WORK_INITIALIZER(mali_mem_os_allocator.timed_shrinker, mali_mem_os_trim_pool),
+#endif
+};
+
+u32 mali_mem_os_free(struct list_head *os_pages, u32 pages_count, mali_bool cow_flag)
+{
+	LIST_HEAD(pages);
+	struct mali_page_node *m_page, *m_tmp;
+	u32 free_pages_nr = 0;
+
+	if (MALI_TRUE == cow_flag) {
+		list_for_each_entry_safe(m_page, m_tmp, os_pages, list) {
+			/*only handle OS node here */
+			if (m_page->type == MALI_PAGE_NODE_OS) {
+				if (1 == _mali_page_node_get_ref_count(m_page)) {
+					list_move(&m_page->list, &pages);
+					atomic_sub(1, &mali_mem_os_allocator.allocated_pages);
+					free_pages_nr ++;
+				} else {
+					_mali_page_node_unref(m_page);
+					m_page->page = NULL;
+					list_del(&m_page->list);
+					kfree(m_page);
+				}
+			}
+		}
+	} else {
+		list_cut_position(&pages, os_pages, os_pages->prev);
+		atomic_sub(pages_count, &mali_mem_os_allocator.allocated_pages);
+		free_pages_nr = pages_count;
+	}
+
+	/* Put pages on pool. */
+	spin_lock(&mali_mem_os_allocator.pool_lock);
+	list_splice(&pages, &mali_mem_os_allocator.pool_pages);
+	mali_mem_os_allocator.pool_count += free_pages_nr;
+	spin_unlock(&mali_mem_os_allocator.pool_lock);
+
+	if (MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES < mali_mem_os_allocator.pool_count) {
+		MALI_DEBUG_PRINT(5, ("OS Mem: Starting pool trim timer %u\n", mali_mem_os_allocator.pool_count));
+		queue_delayed_work(mali_mem_os_allocator.wq, &mali_mem_os_allocator.timed_shrinker, MALI_OS_MEMORY_POOL_TRIM_JIFFIES);
+	}
+	return free_pages_nr;
+}
+
+/**
+* put page without put it into page pool
+*/
+_mali_osk_errcode_t mali_mem_os_put_page(struct page *page)
+{
+	MALI_DEBUG_ASSERT_POINTER(page);
+	if (1 == page_count(page)) {
+		atomic_sub(1, &mali_mem_os_allocator.allocated_pages);
+		dma_unmap_page(&mali_platform_device->dev, page_private(page),
+			       _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+		ClearPagePrivate(page);
+	}
+	put_page(page);
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t mali_mem_os_resize_pages(mali_mem_os_mem *mem_from, mali_mem_os_mem *mem_to, u32 start_page, u32 page_count)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	u32 i = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(mem_from);
+	MALI_DEBUG_ASSERT_POINTER(mem_to);
+
+	if (mem_from->count < start_page + page_count) {
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	}
+
+	list_for_each_entry_safe(m_page, m_tmp, &mem_from->pages, list) {
+		if (i >= start_page && i < start_page + page_count) {
+			list_move_tail(&m_page->list, &mem_to->pages);
+			mem_from->count--;
+			mem_to->count++;
+		}
+		i++;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+
+int mali_mem_os_alloc_pages(mali_mem_os_mem *os_mem, u32 size)
+{
+	struct page *new_page;
+	LIST_HEAD(pages_list);
+	size_t page_count = PAGE_ALIGN(size) / _MALI_OSK_MALI_PAGE_SIZE;
+	size_t remaining = page_count;
+	struct mali_page_node *m_page, *m_tmp;
+	u32 i;
+
+	MALI_DEBUG_ASSERT_POINTER(os_mem);
+
+	if (atomic_read(&mali_mem_os_allocator.allocated_pages) * _MALI_OSK_MALI_PAGE_SIZE + size > mali_mem_os_allocator.allocation_limit) {
+		MALI_DEBUG_PRINT(2, ("Mali Mem: Unable to allocate %u bytes. Currently allocated: %lu, max limit %lu\n",
+				     size,
+				     atomic_read(&mali_mem_os_allocator.allocated_pages) * _MALI_OSK_MALI_PAGE_SIZE,
+				     mali_mem_os_allocator.allocation_limit));
+		return -ENOMEM;
+	}
+
+	INIT_LIST_HEAD(&os_mem->pages);
+	os_mem->count = page_count;
+
+	/* Grab pages from pool. */
+	{
+		size_t pool_pages;
+		spin_lock(&mali_mem_os_allocator.pool_lock);
+		pool_pages = min(remaining, mali_mem_os_allocator.pool_count);
+		for (i = pool_pages; i > 0; i--) {
+			BUG_ON(list_empty(&mali_mem_os_allocator.pool_pages));
+			list_move(mali_mem_os_allocator.pool_pages.next, &pages_list);
+		}
+		mali_mem_os_allocator.pool_count -= pool_pages;
+		remaining -= pool_pages;
+		spin_unlock(&mali_mem_os_allocator.pool_lock);
+	}
+
+	/* Process pages from pool. */
+	i = 0;
+	list_for_each_entry_safe(m_page, m_tmp, &pages_list, list) {
+		BUG_ON(NULL == m_page);
+
+		list_move_tail(&m_page->list, &os_mem->pages);
+	}
+
+	/* Allocate new pages, if needed. */
+	for (i = 0; i < remaining; i++) {
+		dma_addr_t dma_addr;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 15, 0)
+		gfp_t flags = __GFP_ZERO | __GFP_RETRY_MAYFAIL | __GFP_NOWARN;
+#elif LINUX_VERSION_CODE == KERNEL_VERSION(4, 14, 0)
+		gfp_t flags = __GFP_ZERO | __GFP_RETRY_MAYFAIL | __GFP_NOWARN | __GFP_COLD;
+#else
+		gfp_t flags = __GFP_ZERO | __GFP_REPEAT | __GFP_NOWARN | __GFP_COLD;
+#endif
+		int err;
+
+#if defined(CONFIG_ARM) && !defined(CONFIG_ARM_LPAE)
+		flags |= GFP_HIGHUSER;
+#else
+#ifdef CONFIG_ZONE_DMA32
+		flags |= GFP_DMA32;
+#else
+#ifdef CONFIG_ZONE_DMA
+		flags |= GFP_DMA;
+#else
+		/* arm64 utgard only work on < 4G, but the kernel
+		 * didn't provide method to allocte memory < 4G
+		 */
+		MALI_DEBUG_ASSERT(0);
+#endif
+#endif
+#endif
+
+		new_page = alloc_page(flags);
+
+		if (unlikely(NULL == new_page)) {
+			/* Calculate the number of pages actually allocated, and free them. */
+			os_mem->count = (page_count - remaining) + i;
+			atomic_add(os_mem->count, &mali_mem_os_allocator.allocated_pages);
+			mali_mem_os_free(&os_mem->pages, os_mem->count, MALI_FALSE);
+			return -ENOMEM;
+		}
+
+		/* Ensure page is flushed from CPU caches. */
+		dma_addr = dma_map_page(&mali_platform_device->dev, new_page,
+					0, _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+		err = dma_mapping_error(&mali_platform_device->dev, dma_addr);
+		if (likely(!err))
+			dma_unmap_page(&mali_platform_device->dev, dma_addr,
+				       _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+		dma_addr = dma_map_page(&mali_platform_device->dev, new_page,
+					0, _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+
+		err = dma_mapping_error(&mali_platform_device->dev, dma_addr);
+		if (unlikely(err)) {
+			MALI_DEBUG_PRINT_ERROR(("OS Mem: Failed to DMA map page %p: %u",
+						new_page, err));
+			__free_page(new_page);
+			os_mem->count = (page_count - remaining) + i;
+			atomic_add(os_mem->count, &mali_mem_os_allocator.allocated_pages);
+			mali_mem_os_free(&os_mem->pages, os_mem->count, MALI_FALSE);
+			return -EFAULT;
+		}
+
+		/* Store page phys addr */
+		SetPagePrivate(new_page);
+		set_page_private(new_page, dma_addr);
+
+		m_page = _mali_page_node_allocate(MALI_PAGE_NODE_OS);
+		if (unlikely(NULL == m_page)) {
+			MALI_PRINT_ERROR(("OS Mem: Can't allocate mali_page node! \n"));
+			dma_unmap_page(&mali_platform_device->dev, page_private(new_page),
+				       _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+			ClearPagePrivate(new_page);
+			__free_page(new_page);
+			os_mem->count = (page_count - remaining) + i;
+			atomic_add(os_mem->count, &mali_mem_os_allocator.allocated_pages);
+			mali_mem_os_free(&os_mem->pages, os_mem->count, MALI_FALSE);
+			return -EFAULT;
+		}
+		m_page->page = new_page;
+
+		list_add_tail(&m_page->list, &os_mem->pages);
+	}
+
+	atomic_add(page_count, &mali_mem_os_allocator.allocated_pages);
+
+	if (MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES > mali_mem_os_allocator.pool_count) {
+		MALI_DEBUG_PRINT(4, ("OS Mem: Stopping pool trim timer, only %u pages on pool\n", mali_mem_os_allocator.pool_count));
+		cancel_delayed_work(&mali_mem_os_allocator.timed_shrinker);
+	}
+
+	return 0;
+}
+
+
+_mali_osk_errcode_t mali_mem_os_mali_map(mali_mem_os_mem *os_mem, struct mali_session_data *session, u32 vaddr, u32 start_page, u32 mapping_pgae_num, u32 props)
+{
+	struct mali_page_directory *pagedir = session->page_directory;
+	struct mali_page_node *m_page;
+	u32 virt;
+	u32 prop = props;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+	MALI_DEBUG_ASSERT_POINTER(os_mem);
+
+	MALI_DEBUG_ASSERT(start_page <= os_mem->count);
+	MALI_DEBUG_ASSERT((start_page + mapping_pgae_num) <= os_mem->count);
+
+	if ((start_page + mapping_pgae_num) == os_mem->count) {
+
+		virt = vaddr + MALI_MMU_PAGE_SIZE * (start_page + mapping_pgae_num);
+
+		list_for_each_entry_reverse(m_page, &os_mem->pages, list) {
+
+			virt -= MALI_MMU_PAGE_SIZE;
+			if (mapping_pgae_num > 0) {
+				dma_addr_t phys = page_private(m_page->page);
+#if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT)
+				/* Verify that the "physical" address is 32-bit and
+				* usable for Mali, when on a system with bus addresses
+				* wider than 32-bit. */
+				MALI_DEBUG_ASSERT(0 == (phys >> 32));
+#endif
+				mali_mmu_pagedir_update(pagedir, virt, (mali_dma_addr)phys, MALI_MMU_PAGE_SIZE, prop);
+			} else {
+				break;
+			}
+			mapping_pgae_num--;
+		}
+
+	} else {
+		u32 i = 0;
+		virt = vaddr;
+		list_for_each_entry(m_page, &os_mem->pages, list) {
+
+			if (i >= start_page) {
+				dma_addr_t phys = page_private(m_page->page);
+
+#if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT)
+				/* Verify that the "physical" address is 32-bit and
+				* usable for Mali, when on a system with bus addresses
+				* wider than 32-bit. */
+				MALI_DEBUG_ASSERT(0 == (phys >> 32));
+#endif
+				mali_mmu_pagedir_update(pagedir, virt, (mali_dma_addr)phys, MALI_MMU_PAGE_SIZE, prop);
+			}
+			i++;
+			virt += MALI_MMU_PAGE_SIZE;
+		}
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+
+void mali_mem_os_mali_unmap(mali_mem_allocation *alloc)
+{
+	struct mali_session_data *session;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	mali_session_memory_lock(session);
+	mali_mem_mali_map_free(session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+			       alloc->flags);
+	mali_session_memory_unlock(session);
+}
+
+int mali_mem_os_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma)
+{
+	mali_mem_os_mem *os_mem = &mem_bkend->os_mem;
+	struct mali_page_node *m_page;
+	struct page *page;
+	int ret;
+	unsigned long addr = vma->vm_start;
+	MALI_DEBUG_ASSERT(MALI_MEM_OS == mem_bkend->type);
+
+	list_for_each_entry(m_page, &os_mem->pages, list) {
+		/* We should use vm_insert_page, but it does a dcache
+		 * flush which makes it way slower than remap_pfn_range or vm_insert_pfn.
+		ret = vm_insert_page(vma, addr, page);
+		*/
+		page = m_page->page;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+		ret = vmf_insert_pfn(vma, addr, page_to_pfn(page));
+		if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+		ret = vm_insert_pfn(vma, addr, page_to_pfn(page));
+		if (unlikely(0 != ret)) {
+#endif
+
+			return -EFAULT;
+		}
+		addr += _MALI_OSK_MALI_PAGE_SIZE;
+	}
+
+	return 0;
+}
+
+_mali_osk_errcode_t mali_mem_os_resize_cpu_map_locked(mali_mem_backend *mem_bkend, struct vm_area_struct *vma, unsigned long start_vaddr, u32 mappig_size)
+{
+	mali_mem_os_mem *os_mem = &mem_bkend->os_mem;
+	struct mali_page_node *m_page;
+	int ret;
+	int offset;
+	int mapping_page_num;
+	int count ;
+
+	unsigned long vstart = vma->vm_start;
+	count = 0;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_OS);
+	MALI_DEBUG_ASSERT(0 == start_vaddr % _MALI_OSK_MALI_PAGE_SIZE);
+	MALI_DEBUG_ASSERT(0 == vstart % _MALI_OSK_MALI_PAGE_SIZE);
+	offset = (start_vaddr - vstart) / _MALI_OSK_MALI_PAGE_SIZE;
+	MALI_DEBUG_ASSERT(offset <= os_mem->count);
+	mapping_page_num = mappig_size / _MALI_OSK_MALI_PAGE_SIZE;
+	MALI_DEBUG_ASSERT((offset + mapping_page_num) <= os_mem->count);
+
+	if ((offset + mapping_page_num) == os_mem->count) {
+
+		unsigned long vm_end = start_vaddr + mappig_size;
+
+		list_for_each_entry_reverse(m_page, &os_mem->pages, list) {
+
+			vm_end -= _MALI_OSK_MALI_PAGE_SIZE;
+			if (mapping_page_num > 0) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+				ret = vmf_insert_pfn(vma, vm_end, page_to_pfn(m_page->page));
+				if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+				ret = vm_insert_pfn(vma, vm_end, page_to_pfn(m_page->page));
+				if (unlikely(0 != ret)) {
+#endif
+					/*will return -EBUSY If the page has already been mapped into table, but it's OK*/
+					if (-EBUSY == ret) {
+						break;
+					} else {
+						MALI_DEBUG_PRINT(1, ("OS Mem: mali_mem_os_resize_cpu_map_locked failed, ret = %d, offset is %d,page_count is %d\n",
+								     ret,  offset + mapping_page_num, os_mem->count));
+					}
+					return _MALI_OSK_ERR_FAULT;
+				}
+			} else {
+				break;
+			}
+			mapping_page_num--;
+
+		}
+	} else {
+
+		list_for_each_entry(m_page, &os_mem->pages, list) {
+			if (count >= offset) {
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+				ret = vmf_insert_pfn(vma, vstart, page_to_pfn(m_page->page));
+				if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+				ret = vm_insert_pfn(vma, vstart, page_to_pfn(m_page->page));
+				if (unlikely(0 != ret)) {
+#endif
+
+					/*will return -EBUSY If the page has already been mapped into table, but it's OK*/
+					if (-EBUSY == ret) {
+						break;
+					} else {
+						MALI_DEBUG_PRINT(1, ("OS Mem: mali_mem_os_resize_cpu_map_locked failed, ret = %d, count is %d, offset is %d,page_count is %d\n",
+								     ret, count, offset, os_mem->count));
+					}
+					return _MALI_OSK_ERR_FAULT;
+				}
+			}
+			count++;
+			vstart += _MALI_OSK_MALI_PAGE_SIZE;
+		}
+	}
+	return _MALI_OSK_ERR_OK;
+}
+
+u32 mali_mem_os_release(mali_mem_backend *mem_bkend)
+{
+
+	mali_mem_allocation *alloc;
+	struct mali_session_data *session;
+	u32 free_pages_nr = 0;
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend);
+	MALI_DEBUG_ASSERT(MALI_MEM_OS == mem_bkend->type);
+
+	alloc = mem_bkend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	/* Unmap the memory from the mali virtual address space. */
+	mali_mem_os_mali_unmap(alloc);
+	mutex_lock(&mem_bkend->mutex);
+	/* Free pages */
+	if (MALI_MEM_BACKEND_FLAG_COWED & mem_bkend->flags) {
+		/* Lock to avoid the free race condition for the cow shared memory page node. */
+		_mali_osk_mutex_wait(session->cow_lock);
+		free_pages_nr = mali_mem_os_free(&mem_bkend->os_mem.pages, mem_bkend->os_mem.count, MALI_TRUE);
+		_mali_osk_mutex_signal(session->cow_lock);
+	} else {
+		free_pages_nr = mali_mem_os_free(&mem_bkend->os_mem.pages, mem_bkend->os_mem.count, MALI_FALSE);
+	}
+	mutex_unlock(&mem_bkend->mutex);
+
+	MALI_DEBUG_PRINT(4, ("OS Mem free : allocated size = 0x%x, free size = 0x%x\n", mem_bkend->os_mem.count * _MALI_OSK_MALI_PAGE_SIZE,
+			     free_pages_nr * _MALI_OSK_MALI_PAGE_SIZE));
+
+	mem_bkend->os_mem.count = 0;
+	return free_pages_nr;
+}
+
+
+#define MALI_MEM_OS_PAGE_TABLE_PAGE_POOL_SIZE 128
+static struct {
+	struct {
+		mali_dma_addr phys;
+		mali_io_address mapping;
+	} page[MALI_MEM_OS_PAGE_TABLE_PAGE_POOL_SIZE];
+	size_t count;
+	spinlock_t lock;
+} mali_mem_page_table_page_pool = {
+	.count = 0,
+	.lock = __SPIN_LOCK_UNLOCKED(pool_lock),
+};
+
+_mali_osk_errcode_t mali_mem_os_get_table_page(mali_dma_addr *phys, mali_io_address *mapping)
+{
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_NOMEM;
+	dma_addr_t tmp_phys;
+
+	spin_lock(&mali_mem_page_table_page_pool.lock);
+	if (0 < mali_mem_page_table_page_pool.count) {
+		u32 i = --mali_mem_page_table_page_pool.count;
+		*phys = mali_mem_page_table_page_pool.page[i].phys;
+		*mapping = mali_mem_page_table_page_pool.page[i].mapping;
+
+		ret = _MALI_OSK_ERR_OK;
+	}
+	spin_unlock(&mali_mem_page_table_page_pool.lock);
+
+	if (_MALI_OSK_ERR_OK != ret) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 8, 0)
+		*mapping = dma_alloc_attrs(&mali_platform_device->dev,
+					   _MALI_OSK_MALI_PAGE_SIZE, &tmp_phys,
+					   GFP_KERNEL, dma_attrs_wc);
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0)
+		*mapping = dma_alloc_attrs(&mali_platform_device->dev,
+					   _MALI_OSK_MALI_PAGE_SIZE, &tmp_phys,
+					   GFP_KERNEL, &dma_attrs_wc);
+#else
+		*mapping = dma_alloc_writecombine(&mali_platform_device->dev,
+						  _MALI_OSK_MALI_PAGE_SIZE, &tmp_phys, GFP_KERNEL);
+#endif
+		if (NULL != *mapping) {
+			ret = _MALI_OSK_ERR_OK;
+
+#if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT)
+			/* Verify that the "physical" address is 32-bit and
+			 * usable for Mali, when on a system with bus addresses
+			 * wider than 32-bit. */
+			MALI_DEBUG_ASSERT(0 == (tmp_phys >> 32));
+#endif
+
+			*phys = (mali_dma_addr)tmp_phys;
+		}
+	}
+
+	return ret;
+}
+
+void mali_mem_os_release_table_page(mali_dma_addr phys, void *virt)
+{
+	spin_lock(&mali_mem_page_table_page_pool.lock);
+	if (MALI_MEM_OS_PAGE_TABLE_PAGE_POOL_SIZE > mali_mem_page_table_page_pool.count) {
+		u32 i = mali_mem_page_table_page_pool.count;
+		mali_mem_page_table_page_pool.page[i].phys = phys;
+		mali_mem_page_table_page_pool.page[i].mapping = virt;
+
+		++mali_mem_page_table_page_pool.count;
+
+		spin_unlock(&mali_mem_page_table_page_pool.lock);
+	} else {
+		spin_unlock(&mali_mem_page_table_page_pool.lock);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 8, 0)
+		dma_free_attrs(&mali_platform_device->dev,
+			       _MALI_OSK_MALI_PAGE_SIZE, virt, phys,
+			       dma_attrs_wc);
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0)
+		dma_free_attrs(&mali_platform_device->dev,
+			       _MALI_OSK_MALI_PAGE_SIZE, virt, phys,
+			       &dma_attrs_wc);
+#else
+		dma_free_writecombine(&mali_platform_device->dev,
+				      _MALI_OSK_MALI_PAGE_SIZE, virt, phys);
+#endif
+	}
+}
+
+void mali_mem_os_free_page_node(struct mali_page_node *m_page)
+{
+	struct page *page = m_page->page;
+	MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_OS);
+
+	if (1  == page_count(page)) {
+		dma_unmap_page(&mali_platform_device->dev, page_private(page),
+			       _MALI_OSK_MALI_PAGE_SIZE, DMA_BIDIRECTIONAL);
+		ClearPagePrivate(page);
+	}
+	__free_page(page);
+	m_page->page = NULL;
+	list_del(&m_page->list);
+	kfree(m_page);
+}
+
+/* The maximum number of page table pool pages to free in one go. */
+#define MALI_MEM_OS_CHUNK_TO_FREE 64UL
+
+/* Free a certain number of pages from the page table page pool.
+ * The pool lock must be held when calling the function, and the lock will be
+ * released before returning.
+ */
+static void mali_mem_os_page_table_pool_free(size_t nr_to_free)
+{
+	mali_dma_addr phys_arr[MALI_MEM_OS_CHUNK_TO_FREE];
+	void *virt_arr[MALI_MEM_OS_CHUNK_TO_FREE];
+	u32 i;
+
+	MALI_DEBUG_ASSERT(nr_to_free <= MALI_MEM_OS_CHUNK_TO_FREE);
+
+	/* Remove nr_to_free pages from the pool and store them locally on stack. */
+	for (i = 0; i < nr_to_free; i++) {
+		u32 pool_index = mali_mem_page_table_page_pool.count - i - 1;
+
+		phys_arr[i] = mali_mem_page_table_page_pool.page[pool_index].phys;
+		virt_arr[i] = mali_mem_page_table_page_pool.page[pool_index].mapping;
+	}
+
+	mali_mem_page_table_page_pool.count -= nr_to_free;
+
+	spin_unlock(&mali_mem_page_table_page_pool.lock);
+
+	/* After releasing the spinlock: free the pages we removed from the pool. */
+	for (i = 0; i < nr_to_free; i++) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 8, 0)
+		dma_free_attrs(&mali_platform_device->dev, _MALI_OSK_MALI_PAGE_SIZE,
+			       virt_arr[i], (dma_addr_t)phys_arr[i], dma_attrs_wc);
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0)
+		dma_free_attrs(&mali_platform_device->dev, _MALI_OSK_MALI_PAGE_SIZE,
+			       virt_arr[i], (dma_addr_t)phys_arr[i], &dma_attrs_wc);
+#else
+		dma_free_writecombine(&mali_platform_device->dev,
+				      _MALI_OSK_MALI_PAGE_SIZE,
+				      virt_arr[i], (dma_addr_t)phys_arr[i]);
+#endif
+	}
+}
+
+static void mali_mem_os_trim_page_table_page_pool(void)
+{
+	size_t nr_to_free = 0;
+	size_t nr_to_keep;
+
+	/* Keep 2 page table pages for each 1024 pages in the page cache. */
+	nr_to_keep = mali_mem_os_allocator.pool_count / 512;
+	/* And a minimum of eight pages, to accomodate new sessions. */
+	nr_to_keep += 8;
+
+	if (0 == spin_trylock(&mali_mem_page_table_page_pool.lock)) return;
+
+	if (nr_to_keep < mali_mem_page_table_page_pool.count) {
+		nr_to_free = mali_mem_page_table_page_pool.count - nr_to_keep;
+		nr_to_free = min((size_t)MALI_MEM_OS_CHUNK_TO_FREE, nr_to_free);
+	}
+
+	/* Pool lock will be released by the callee. */
+	mali_mem_os_page_table_pool_free(nr_to_free);
+}
+
+static unsigned long mali_mem_os_shrink_count(struct shrinker *shrinker, struct shrink_control *sc)
+{
+	return mali_mem_os_allocator.pool_count;
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 0, 0)
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 35)
+static int mali_mem_os_shrink(int nr_to_scan, gfp_t gfp_mask)
+#else
+static int mali_mem_os_shrink(struct shrinker *shrinker, int nr_to_scan, gfp_t gfp_mask)
+#endif /* Linux < 2.6.35 */
+#else
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 12, 0)
+static int mali_mem_os_shrink(struct shrinker *shrinker, struct shrink_control *sc)
+#else
+static unsigned long mali_mem_os_shrink(struct shrinker *shrinker, struct shrink_control *sc)
+#endif /* Linux < 3.12.0 */
+#endif /* Linux < 3.0.0 */
+{
+	struct mali_page_node *m_page, *m_tmp;
+	unsigned long flags;
+	struct list_head *le, pages;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 0, 0)
+	int nr = nr_to_scan;
+#else
+	int nr = sc->nr_to_scan;
+#endif
+
+	if (0 == nr) {
+		return mali_mem_os_shrink_count(shrinker, sc);
+	}
+
+	if (0 == spin_trylock_irqsave(&mali_mem_os_allocator.pool_lock, flags)) {
+		/* Not able to lock. */
+		return -1;
+	}
+
+	if (0 == mali_mem_os_allocator.pool_count) {
+		/* No pages availble */
+		spin_unlock_irqrestore(&mali_mem_os_allocator.pool_lock, flags);
+		return 0;
+	}
+
+	/* Release from general page pool */
+	nr = min((size_t)nr, mali_mem_os_allocator.pool_count);
+	mali_mem_os_allocator.pool_count -= nr;
+	list_for_each(le, &mali_mem_os_allocator.pool_pages) {
+		--nr;
+		if (0 == nr) break;
+	}
+	list_cut_position(&pages, &mali_mem_os_allocator.pool_pages, le);
+	spin_unlock_irqrestore(&mali_mem_os_allocator.pool_lock, flags);
+
+	list_for_each_entry_safe(m_page, m_tmp, &pages, list) {
+		mali_mem_os_free_page_node(m_page);
+	}
+
+	if (MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES > mali_mem_os_allocator.pool_count) {
+		/* Pools are empty, stop timer */
+		MALI_DEBUG_PRINT(5, ("Stopping timer, only %u pages on pool\n", mali_mem_os_allocator.pool_count));
+		cancel_delayed_work(&mali_mem_os_allocator.timed_shrinker);
+	}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 12, 0)
+	return mali_mem_os_shrink_count(shrinker, sc);
+#else
+	return nr;
+#endif
+}
+
+static void mali_mem_os_trim_pool(struct work_struct *data)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	struct list_head *le;
+	LIST_HEAD(pages);
+	size_t nr_to_free;
+
+	MALI_IGNORE(data);
+
+	MALI_DEBUG_PRINT(3, ("OS Mem: Trimming pool %u\n", mali_mem_os_allocator.pool_count));
+
+	/* Release from general page pool */
+	spin_lock(&mali_mem_os_allocator.pool_lock);
+	if (MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES < mali_mem_os_allocator.pool_count) {
+		size_t count = mali_mem_os_allocator.pool_count - MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES;
+		const size_t min_to_free = min(64, MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES);
+
+		/* Free half the pages on the pool above the static limit. Or 64 pages, 256KB. */
+		nr_to_free = max(count / 2, min_to_free);
+
+		mali_mem_os_allocator.pool_count -= nr_to_free;
+		list_for_each(le, &mali_mem_os_allocator.pool_pages) {
+			--nr_to_free;
+			if (0 == nr_to_free) break;
+		}
+		list_cut_position(&pages, &mali_mem_os_allocator.pool_pages, le);
+	}
+	spin_unlock(&mali_mem_os_allocator.pool_lock);
+
+	list_for_each_entry_safe(m_page, m_tmp, &pages, list) {
+		mali_mem_os_free_page_node(m_page);
+	}
+
+	/* Release some pages from page table page pool */
+	mali_mem_os_trim_page_table_page_pool();
+
+	if (MALI_OS_MEMORY_KERNEL_BUFFER_SIZE_IN_PAGES < mali_mem_os_allocator.pool_count) {
+		MALI_DEBUG_PRINT(4, ("OS Mem: Starting pool trim timer %u\n", mali_mem_os_allocator.pool_count));
+		queue_delayed_work(mali_mem_os_allocator.wq, &mali_mem_os_allocator.timed_shrinker, MALI_OS_MEMORY_POOL_TRIM_JIFFIES);
+	}
+}
+
+_mali_osk_errcode_t mali_mem_os_init(void)
+{
+	mali_mem_os_allocator.wq = alloc_workqueue("mali-mem", WQ_UNBOUND, 1);
+	if (NULL == mali_mem_os_allocator.wq) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+#if LINUX_VERSION_CODE >=  KERNEL_VERSION(4, 8, 0)
+	dma_attrs_wc = DMA_ATTR_WRITE_COMBINE;
+#elif LINUX_VERSION_CODE >= KERNEL_VERSION(3, 8, 0)
+	dma_set_attr(DMA_ATTR_WRITE_COMBINE, &dma_attrs_wc);
+#endif
+
+	register_shrinker(&mali_mem_os_allocator.shrinker);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mem_os_term(void)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	unregister_shrinker(&mali_mem_os_allocator.shrinker);
+	cancel_delayed_work_sync(&mali_mem_os_allocator.timed_shrinker);
+
+	if (NULL != mali_mem_os_allocator.wq) {
+		destroy_workqueue(mali_mem_os_allocator.wq);
+		mali_mem_os_allocator.wq = NULL;
+	}
+
+	spin_lock(&mali_mem_os_allocator.pool_lock);
+	list_for_each_entry_safe(m_page, m_tmp, &mali_mem_os_allocator.pool_pages, list) {
+		mali_mem_os_free_page_node(m_page);
+
+		--mali_mem_os_allocator.pool_count;
+	}
+	BUG_ON(mali_mem_os_allocator.pool_count);
+	spin_unlock(&mali_mem_os_allocator.pool_lock);
+
+	/* Release from page table page pool */
+	do {
+		u32 nr_to_free;
+
+		spin_lock(&mali_mem_page_table_page_pool.lock);
+
+		nr_to_free = min((size_t)MALI_MEM_OS_CHUNK_TO_FREE, mali_mem_page_table_page_pool.count);
+
+		/* Pool lock will be released by the callee. */
+		mali_mem_os_page_table_pool_free(nr_to_free);
+	} while (0 != mali_mem_page_table_page_pool.count);
+}
+
+_mali_osk_errcode_t mali_memory_core_resource_os_memory(u32 size)
+{
+	mali_mem_os_allocator.allocation_limit = size;
+
+	MALI_SUCCESS;
+}
+
+u32 mali_mem_os_stat(void)
+{
+	return atomic_read(&mali_mem_os_allocator.allocated_pages) * _MALI_OSK_MALI_PAGE_SIZE;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_os_alloc.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_os_alloc.h
@@ -0,0 +1,54 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_OS_ALLOC_H__
+#define __MALI_MEMORY_OS_ALLOC_H__
+
+#include "mali_osk.h"
+#include "mali_memory_types.h"
+
+
+/** @brief Release Mali OS memory
+ *
+ * The session memory_lock must be held when calling this function.
+ *
+ * @param mem_bkend Pointer to the mali_mem_backend to release
+ */
+u32 mali_mem_os_release(mali_mem_backend *mem_bkend);
+
+_mali_osk_errcode_t mali_mem_os_get_table_page(mali_dma_addr *phys, mali_io_address *mapping);
+
+void mali_mem_os_release_table_page(mali_dma_addr phys, void *virt);
+
+_mali_osk_errcode_t mali_mem_os_init(void);
+
+void mali_mem_os_term(void);
+
+u32 mali_mem_os_stat(void);
+
+void mali_mem_os_free_page_node(struct mali_page_node *m_page);
+
+int mali_mem_os_alloc_pages(mali_mem_os_mem *os_mem, u32 size);
+
+u32 mali_mem_os_free(struct list_head *os_pages, u32 pages_count, mali_bool cow_flag);
+
+_mali_osk_errcode_t mali_mem_os_put_page(struct page *page);
+
+_mali_osk_errcode_t mali_mem_os_resize_pages(mali_mem_os_mem *mem_from, mali_mem_os_mem *mem_to, u32 start_page, u32 page_count);
+
+_mali_osk_errcode_t mali_mem_os_mali_map(mali_mem_os_mem *os_mem, struct mali_session_data *session, u32 vaddr, u32 start_page, u32 mapping_pgae_num, u32 props);
+
+void mali_mem_os_mali_unmap(mali_mem_allocation *alloc);
+
+int mali_mem_os_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma);
+
+_mali_osk_errcode_t mali_mem_os_resize_cpu_map_locked(mali_mem_backend *mem_bkend, struct vm_area_struct *vma, unsigned long start_vaddr, u32 mappig_size);
+
+#endif /* __MALI_MEMORY_OS_ALLOC_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_secure.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_secure.c
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2010-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_memory.h"
+#include "mali_memory_secure.h"
+#include "mali_osk.h"
+#include <linux/mutex.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 16, 0)
+#include <linux/dma-direct.h>
+#else
+#include <linux/dma-mapping.h>
+#endif
+#include <linux/dma-buf.h>
+
+_mali_osk_errcode_t mali_mem_secure_attach_dma_buf(mali_mem_secure *secure_mem, u32 size, int mem_fd)
+{
+	struct dma_buf *buf;
+	MALI_DEBUG_ASSERT_POINTER(secure_mem);
+
+	/* get dma buffer */
+	buf = dma_buf_get(mem_fd);
+	if (IS_ERR_OR_NULL(buf)) {
+		MALI_DEBUG_PRINT_ERROR(("Failed to get dma buf!\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	if (size != buf->size) {
+		MALI_DEBUG_PRINT_ERROR(("The secure mem size not match to the dma buf size!\n"));
+		goto failed_alloc_mem;
+	}
+
+	secure_mem->buf =  buf;
+	secure_mem->attachment = dma_buf_attach(secure_mem->buf, &mali_platform_device->dev);
+	if (NULL == secure_mem->attachment) {
+		MALI_DEBUG_PRINT_ERROR(("Failed to get dma buf attachment!\n"));
+		goto failed_dma_attach;
+	}
+
+	secure_mem->sgt = dma_buf_map_attachment(secure_mem->attachment, DMA_BIDIRECTIONAL);
+	if (IS_ERR_OR_NULL(secure_mem->sgt)) {
+		MALI_DEBUG_PRINT_ERROR(("Failed to map dma buf attachment\n"));
+		goto  failed_dma_map;
+	}
+
+	secure_mem->count = size / MALI_MMU_PAGE_SIZE;
+
+	return _MALI_OSK_ERR_OK;
+
+failed_dma_map:
+	dma_buf_detach(secure_mem->buf, secure_mem->attachment);
+failed_dma_attach:
+failed_alloc_mem:
+	dma_buf_put(buf);
+	return _MALI_OSK_ERR_FAULT;
+}
+
+_mali_osk_errcode_t mali_mem_secure_mali_map(mali_mem_secure *secure_mem, struct mali_session_data *session, u32 vaddr, u32 props)
+{
+	struct mali_page_directory *pagedir;
+	struct scatterlist *sg;
+	u32 virt = vaddr;
+	u32 prop = props;
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(secure_mem);
+	MALI_DEBUG_ASSERT_POINTER(secure_mem->sgt);
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	pagedir = session->page_directory;
+
+	for_each_sg(secure_mem->sgt->sgl, sg, secure_mem->sgt->nents, i) {
+		u32 size = sg_dma_len(sg);
+		dma_addr_t phys = sg_dma_address(sg);
+
+		/* sg must be page aligned. */
+		MALI_DEBUG_ASSERT(0 == size % MALI_MMU_PAGE_SIZE);
+		MALI_DEBUG_ASSERT(0 == (phys & ~(uintptr_t)0xFFFFFFFF));
+
+		mali_mmu_pagedir_update(pagedir, virt, phys, size, prop);
+
+		MALI_DEBUG_PRINT(3, ("The secure mem physical address: 0x%x gpu virtual address: 0x%x! \n", phys, virt));
+		virt += size;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mem_secure_mali_unmap(mali_mem_allocation *alloc)
+{
+	struct mali_session_data *session;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	mali_session_memory_lock(session);
+	mali_mem_mali_map_free(session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+			       alloc->flags);
+	mali_session_memory_unlock(session);
+}
+
+
+int mali_mem_secure_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma)
+{
+
+	int ret = 0;
+	struct scatterlist *sg;
+	mali_mem_secure *secure_mem = &mem_bkend->secure_mem;
+	unsigned long addr = vma->vm_start;
+	int i;
+
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_SECURE);
+
+	for_each_sg(secure_mem->sgt->sgl, sg, secure_mem->sgt->nents, i) {
+		phys_addr_t phys;
+		dma_addr_t dev_addr;
+		u32 size, j;
+		dev_addr = sg_dma_address(sg);
+#if defined(CONFIG_ARM64) ||LINUX_VERSION_CODE >= KERNEL_VERSION(3, 13, 0)
+		phys =  dma_to_phys(&mali_platform_device->dev, dev_addr);
+#else
+		phys = page_to_phys(pfn_to_page(dma_to_pfn(&mali_platform_device->dev, dev_addr)));
+#endif
+		size = sg_dma_len(sg);
+		MALI_DEBUG_ASSERT(0 == size % _MALI_OSK_MALI_PAGE_SIZE);
+
+		for (j = 0; j < size / _MALI_OSK_MALI_PAGE_SIZE; j++) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+			ret = vmf_insert_pfn(vma, addr, PFN_DOWN(phys));
+			if (unlikely(VM_FAULT_ERROR & ret)) {
+#else
+			ret = vm_insert_pfn(vma, addr, PFN_DOWN(phys));
+			if (unlikely(0 != ret)) {
+#endif
+
+				return -EFAULT;
+			}
+			addr += _MALI_OSK_MALI_PAGE_SIZE;
+			phys += _MALI_OSK_MALI_PAGE_SIZE;
+
+			MALI_DEBUG_PRINT(3, ("The secure mem physical address: 0x%x , cpu virtual address: 0x%x! \n", phys, addr));
+		}
+	}
+	return ret;
+}
+
+u32 mali_mem_secure_release(mali_mem_backend *mem_bkend)
+{
+	struct mali_mem_secure *mem;
+	mali_mem_allocation *alloc = mem_bkend->mali_allocation;
+	u32 free_pages_nr = 0;
+	MALI_DEBUG_ASSERT(mem_bkend->type == MALI_MEM_SECURE);
+
+	mem = &mem_bkend->secure_mem;
+	MALI_DEBUG_ASSERT_POINTER(mem->attachment);
+	MALI_DEBUG_ASSERT_POINTER(mem->buf);
+	MALI_DEBUG_ASSERT_POINTER(mem->sgt);
+	/* Unmap the memory from the mali virtual address space. */
+	mali_mem_secure_mali_unmap(alloc);
+	mutex_lock(&mem_bkend->mutex);
+	dma_buf_unmap_attachment(mem->attachment, mem->sgt, DMA_BIDIRECTIONAL);
+	dma_buf_detach(mem->buf, mem->attachment);
+	dma_buf_put(mem->buf);
+	mutex_unlock(&mem_bkend->mutex);
+
+	free_pages_nr = mem->count;
+
+	return free_pages_nr;
+}
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_secure.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_secure.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2010, 2013, 2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_SECURE_H__
+#define __MALI_MEMORY_SECURE_H__
+
+#include "mali_session.h"
+#include "mali_memory.h"
+#include <linux/spinlock.h>
+
+#include "mali_memory_types.h"
+
+_mali_osk_errcode_t mali_mem_secure_attach_dma_buf(mali_mem_secure *secure_mem, u32 size, int mem_fd);
+
+_mali_osk_errcode_t mali_mem_secure_mali_map(mali_mem_secure *secure_mem, struct mali_session_data *session, u32 vaddr, u32 props);
+
+void mali_mem_secure_mali_unmap(mali_mem_allocation *alloc);
+
+int mali_mem_secure_cpu_map(mali_mem_backend *mem_bkend, struct vm_area_struct *vma);
+
+u32 mali_mem_secure_release(mali_mem_backend *mem_bkend);
+
+#endif /* __MALI_MEMORY_SECURE_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_swap_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_swap_alloc.c
@@ -0,0 +1,949 @@
+/*
+ * Copyright (C) 2013-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/slab.h>
+#include <linux/version.h>
+#include <linux/sched.h>
+#include <linux/idr.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+#include <linux/shmem_fs.h>
+#include <linux/file.h>
+#include <linux/swap.h>
+#include <linux/pagemap.h>
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_memory.h"
+#include "mali_memory_manager.h"
+#include "mali_memory_virtual.h"
+#include "mali_memory_cow.h"
+#include "mali_ukk.h"
+#include "mali_kernel_utilization.h"
+#include "mali_memory_swap_alloc.h"
+
+
+static struct _mali_osk_bitmap idx_mgr;
+static struct file *global_swap_file;
+static struct address_space *global_swap_space;
+static _mali_osk_wq_work_t *mali_mem_swap_out_workq = NULL;
+static u32 mem_backend_swapped_pool_size;
+#ifdef MALI_MEM_SWAP_TRACKING
+static u32 mem_backend_swapped_unlock_size;
+#endif
+/* Lock order: mem_backend_swapped_pool_lock  > each memory backend's mutex lock.
+ * This lock used to protect mem_backend_swapped_pool_size and mem_backend_swapped_pool. */
+static struct mutex mem_backend_swapped_pool_lock;
+static struct list_head mem_backend_swapped_pool;
+
+extern struct mali_mem_os_allocator mali_mem_os_allocator;
+
+#define MALI_SWAP_LOW_MEM_DEFAULT_VALUE (60*1024*1024)
+#define MALI_SWAP_INVALIDATE_MALI_ADDRESS (0)               /* Used to mark the given memory cookie is invalidate. */
+#define MALI_SWAP_GLOBAL_SWAP_FILE_SIZE (0xFFFFFFFF)
+#define MALI_SWAP_GLOBAL_SWAP_FILE_INDEX ((MALI_SWAP_GLOBAL_SWAP_FILE_SIZE) >> PAGE_SHIFT)
+#define MALI_SWAP_GLOBAL_SWAP_FILE_INDEX_RESERVE (1 << 15) /* Reserved for CoW nonlinear swap backend memory, the space size is 128MB. */
+
+unsigned int mali_mem_swap_out_threshold_value = MALI_SWAP_LOW_MEM_DEFAULT_VALUE;
+
+/**
+ * We have two situations to do shrinking things, one is we met low GPU utilization which shows GPU needn't touch too
+ * swappable backends in short time, and the other one is we add new swappable backends, the total pool size exceed
+ * the threshold value of the swapped pool size.
+ */
+typedef enum {
+	MALI_MEM_SWAP_SHRINK_WITH_LOW_UTILIZATION = 100,
+	MALI_MEM_SWAP_SHRINK_FOR_ADDING_NEW_BACKENDS = 257,
+} _mali_mem_swap_pool_shrink_type_t;
+
+static void mali_mem_swap_swapped_bkend_pool_check_for_low_utilization(void *arg);
+
+_mali_osk_errcode_t mali_mem_swap_init(void)
+{
+	gfp_t flags = __GFP_NORETRY | __GFP_NOWARN;
+
+	if (_MALI_OSK_ERR_OK != _mali_osk_bitmap_init(&idx_mgr, MALI_SWAP_GLOBAL_SWAP_FILE_INDEX, MALI_SWAP_GLOBAL_SWAP_FILE_INDEX_RESERVE)) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	global_swap_file = shmem_file_setup("mali_swap", MALI_SWAP_GLOBAL_SWAP_FILE_SIZE, VM_NORESERVE);
+	if (IS_ERR(global_swap_file)) {
+		_mali_osk_bitmap_term(&idx_mgr);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	global_swap_space = global_swap_file->f_path.dentry->d_inode->i_mapping;
+
+	mali_mem_swap_out_workq = _mali_osk_wq_create_work(mali_mem_swap_swapped_bkend_pool_check_for_low_utilization, NULL);
+	if (NULL == mali_mem_swap_out_workq) {
+		_mali_osk_bitmap_term(&idx_mgr);
+		fput(global_swap_file);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+#if defined(CONFIG_ARM) && !defined(CONFIG_ARM_LPAE)
+	flags |= GFP_HIGHUSER;
+#else
+#ifdef CONFIG_ZONE_DMA32
+	flags |= GFP_DMA32;
+#else
+#ifdef CONFIG_ZONE_DMA
+	flags |= GFP_DMA;
+#else
+	/* arm64 utgard only work on < 4G, but the kernel
+	 * didn't provide method to allocte memory < 4G
+	 */
+	MALI_DEBUG_ASSERT(0);
+#endif
+#endif
+#endif
+
+	/* When we use shmem_read_mapping_page to allocate/swap-in, it will
+	 * use these flags to allocate new page if need.*/
+	mapping_set_gfp_mask(global_swap_space, flags);
+
+	mem_backend_swapped_pool_size = 0;
+#ifdef MALI_MEM_SWAP_TRACKING
+	mem_backend_swapped_unlock_size = 0;
+#endif
+	mutex_init(&mem_backend_swapped_pool_lock);
+	INIT_LIST_HEAD(&mem_backend_swapped_pool);
+
+	MALI_DEBUG_PRINT(2, ("Mali SWAP: Swap out threshold vaule is %uM\n", mali_mem_swap_out_threshold_value >> 20));
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mem_swap_term(void)
+{
+	_mali_osk_bitmap_term(&idx_mgr);
+
+	fput(global_swap_file);
+
+	_mali_osk_wq_delete_work(mali_mem_swap_out_workq);
+
+	MALI_DEBUG_ASSERT(list_empty(&mem_backend_swapped_pool));
+	MALI_DEBUG_ASSERT(0 == mem_backend_swapped_pool_size);
+
+	return;
+}
+
+struct file *mali_mem_swap_get_global_swap_file(void)
+{
+	return  global_swap_file;
+}
+
+/* Judge if swappable backend in swapped pool. */
+static mali_bool mali_memory_swap_backend_in_swapped_pool(mali_mem_backend *mem_bkend)
+{
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend);
+
+	return !list_empty(&mem_bkend->list);
+}
+
+void mali_memory_swap_list_backend_delete(mali_mem_backend *mem_bkend)
+{
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend);
+
+	mutex_lock(&mem_backend_swapped_pool_lock);
+	mutex_lock(&mem_bkend->mutex);
+
+	if (MALI_FALSE == mali_memory_swap_backend_in_swapped_pool(mem_bkend)) {
+		mutex_unlock(&mem_bkend->mutex);
+		mutex_unlock(&mem_backend_swapped_pool_lock);
+		return;
+	}
+
+	MALI_DEBUG_ASSERT(!list_empty(&mem_bkend->list));
+
+	list_del_init(&mem_bkend->list);
+
+	mutex_unlock(&mem_bkend->mutex);
+
+	mem_backend_swapped_pool_size -= mem_bkend->size;
+
+	mutex_unlock(&mem_backend_swapped_pool_lock);
+}
+
+static void mali_mem_swap_out_page_node(mali_page_node *page_node)
+{
+	MALI_DEBUG_ASSERT(page_node);
+
+	dma_unmap_page(&mali_platform_device->dev, page_node->swap_it->dma_addr,
+		       _MALI_OSK_MALI_PAGE_SIZE, DMA_TO_DEVICE);
+	set_page_dirty(page_node->swap_it->page);
+	put_page(page_node->swap_it->page);
+}
+
+void mali_mem_swap_unlock_single_mem_backend(mali_mem_backend *mem_bkend)
+{
+	mali_page_node *m_page;
+
+	MALI_DEBUG_ASSERT(1 == mutex_is_locked(&mem_bkend->mutex));
+
+	if (MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN == (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN)) {
+		return;
+	}
+
+	mem_bkend->flags |= MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN;
+
+	list_for_each_entry(m_page, &mem_bkend->swap_mem.pages, list) {
+		mali_mem_swap_out_page_node(m_page);
+	}
+
+	return;
+}
+
+static void mali_mem_swap_unlock_partial_locked_mem_backend(mali_mem_backend *mem_bkend, mali_page_node *page_node)
+{
+	mali_page_node *m_page;
+
+	MALI_DEBUG_ASSERT(1 == mutex_is_locked(&mem_bkend->mutex));
+
+	list_for_each_entry(m_page, &mem_bkend->swap_mem.pages, list) {
+		if (m_page == page_node) {
+			break;
+		}
+		mali_mem_swap_out_page_node(m_page);
+	}
+}
+
+static void mali_mem_swap_swapped_bkend_pool_shrink(_mali_mem_swap_pool_shrink_type_t shrink_type)
+{
+	mali_mem_backend *bkend, *tmp_bkend;
+	long system_free_size;
+	u32 last_gpu_utilization, gpu_utilization_threshold_value, temp_swap_out_threshold_value;
+
+	MALI_DEBUG_ASSERT(1 == mutex_is_locked(&mem_backend_swapped_pool_lock));
+
+	if (MALI_MEM_SWAP_SHRINK_WITH_LOW_UTILIZATION == shrink_type) {
+		/**
+		 * When we met that system memory is very low and Mali locked swappable memory size is less than
+		 * threshold value, and at the same time, GPU load is very low and don't need high performance,
+		 * at this condition, we can unlock more swap memory backend from swapped backends pool.
+		 */
+		gpu_utilization_threshold_value = MALI_MEM_SWAP_SHRINK_WITH_LOW_UTILIZATION;
+		temp_swap_out_threshold_value = (mali_mem_swap_out_threshold_value >> 2);
+	} else {
+		/* When we add swappable memory backends to swapped pool, we need to think that we couldn't
+		* hold too much swappable backends in Mali driver, and also we need considering performance.
+		* So there is a balance for swapping out memory backend, we should follow the following conditions:
+		* 1. Total memory size in global mem backend swapped pool is more than the defined threshold value.
+		* 2. System level free memory size is less than the defined threshold value.
+		* 3. Please note that GPU utilization problem isn't considered in this condition.
+		*/
+		gpu_utilization_threshold_value = MALI_MEM_SWAP_SHRINK_FOR_ADDING_NEW_BACKENDS;
+		temp_swap_out_threshold_value = mali_mem_swap_out_threshold_value;
+	}
+
+	/* Get system free pages number. */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+	system_free_size = global_zone_page_state(NR_FREE_PAGES) * PAGE_SIZE;
+#else
+	system_free_size = global_page_state(NR_FREE_PAGES) * PAGE_SIZE;
+#endif
+	last_gpu_utilization = _mali_ukk_utilization_gp_pp();
+
+	if ((last_gpu_utilization < gpu_utilization_threshold_value)
+	    && (system_free_size < mali_mem_swap_out_threshold_value)
+	    && (mem_backend_swapped_pool_size > temp_swap_out_threshold_value)) {
+		list_for_each_entry_safe(bkend, tmp_bkend, &mem_backend_swapped_pool, list) {
+			if (mem_backend_swapped_pool_size <= temp_swap_out_threshold_value) {
+				break;
+			}
+
+			mutex_lock(&bkend->mutex);
+
+			/* check if backend is in use. */
+			if (0 < bkend->using_count) {
+				mutex_unlock(&bkend->mutex);
+				continue;
+			}
+
+			mali_mem_swap_unlock_single_mem_backend(bkend);
+			list_del_init(&bkend->list);
+			mem_backend_swapped_pool_size -= bkend->size;
+#ifdef MALI_MEM_SWAP_TRACKING
+			mem_backend_swapped_unlock_size += bkend->size;
+#endif
+			mutex_unlock(&bkend->mutex);
+		}
+	}
+
+	return;
+}
+
+static void mali_mem_swap_swapped_bkend_pool_check_for_low_utilization(void *arg)
+{
+	MALI_IGNORE(arg);
+
+	mutex_lock(&mem_backend_swapped_pool_lock);
+
+	mali_mem_swap_swapped_bkend_pool_shrink(MALI_MEM_SWAP_SHRINK_WITH_LOW_UTILIZATION);
+
+	mutex_unlock(&mem_backend_swapped_pool_lock);
+}
+
+/**
+ * After PP job finished, we add all of swappable memory backend used by this PP
+ * job to the tail of the global swapped pool, and if the total size of swappable memory is more than threshold
+ * value, we also need to shrink the swapped pool start from the head of the list.
+ */
+void mali_memory_swap_list_backend_add(mali_mem_backend *mem_bkend)
+{
+	mutex_lock(&mem_backend_swapped_pool_lock);
+	mutex_lock(&mem_bkend->mutex);
+
+	if (mali_memory_swap_backend_in_swapped_pool(mem_bkend)) {
+		MALI_DEBUG_ASSERT(!list_empty(&mem_bkend->list));
+
+		list_del_init(&mem_bkend->list);
+		list_add_tail(&mem_bkend->list, &mem_backend_swapped_pool);
+		mutex_unlock(&mem_bkend->mutex);
+		mutex_unlock(&mem_backend_swapped_pool_lock);
+		return;
+	}
+
+	list_add_tail(&mem_bkend->list, &mem_backend_swapped_pool);
+
+	mutex_unlock(&mem_bkend->mutex);
+	mem_backend_swapped_pool_size += mem_bkend->size;
+
+	mali_mem_swap_swapped_bkend_pool_shrink(MALI_MEM_SWAP_SHRINK_FOR_ADDING_NEW_BACKENDS);
+
+	mutex_unlock(&mem_backend_swapped_pool_lock);
+	return;
+}
+
+
+u32 mali_mem_swap_idx_alloc(void)
+{
+	return _mali_osk_bitmap_alloc(&idx_mgr);
+}
+
+void mali_mem_swap_idx_free(u32 idx)
+{
+	_mali_osk_bitmap_free(&idx_mgr, idx);
+}
+
+static u32 mali_mem_swap_idx_range_alloc(u32 count)
+{
+	u32 index;
+
+	index = _mali_osk_bitmap_alloc_range(&idx_mgr, count);
+
+	return index;
+}
+
+static void mali_mem_swap_idx_range_free(u32 idx, int num)
+{
+	_mali_osk_bitmap_free_range(&idx_mgr, idx, num);
+}
+
+struct mali_swap_item *mali_mem_swap_alloc_swap_item(void)
+{
+	mali_swap_item *swap_item;
+
+	swap_item = kzalloc(sizeof(mali_swap_item), GFP_KERNEL);
+
+	if (NULL == swap_item) {
+		return NULL;
+	}
+
+	atomic_set(&swap_item->ref_count, 1);
+	swap_item->page = NULL;
+	atomic_add(1, &mali_mem_os_allocator.allocated_pages);
+
+	return swap_item;
+}
+
+void mali_mem_swap_free_swap_item(mali_swap_item *swap_item)
+{
+	struct inode *file_node;
+	long long start, end;
+
+	/* If this swap item is shared, we just reduce the reference counter. */
+	if (0 == atomic_dec_return(&swap_item->ref_count)) {
+		file_node = global_swap_file->f_path.dentry->d_inode;
+		start = swap_item->idx;
+		start = start << 12;
+		end = start + PAGE_SIZE;
+
+		shmem_truncate_range(file_node, start, (end - 1));
+
+		mali_mem_swap_idx_free(swap_item->idx);
+
+		atomic_sub(1, &mali_mem_os_allocator.allocated_pages);
+
+		kfree(swap_item);
+	}
+}
+
+/* Used to allocate new swap item for new memory allocation and cow page for write. */
+struct mali_page_node *_mali_mem_swap_page_node_allocate(void)
+{
+	struct mali_page_node *m_page;
+
+	m_page = _mali_page_node_allocate(MALI_PAGE_NODE_SWAP);
+
+	if (NULL == m_page) {
+		return NULL;
+	}
+
+	m_page->swap_it = mali_mem_swap_alloc_swap_item();
+
+	if (NULL == m_page->swap_it) {
+		kfree(m_page);
+		return NULL;
+	}
+
+	return m_page;
+}
+
+_mali_osk_errcode_t _mali_mem_swap_put_page_node(struct mali_page_node *m_page)
+{
+
+	mali_mem_swap_free_swap_item(m_page->swap_it);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void _mali_mem_swap_page_node_free(struct mali_page_node *m_page)
+{
+	_mali_mem_swap_put_page_node(m_page);
+
+	kfree(m_page);
+
+	return;
+}
+
+u32 mali_mem_swap_free(mali_mem_swap *swap_mem)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	u32 free_pages_nr = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(swap_mem);
+
+	list_for_each_entry_safe(m_page, m_tmp, &swap_mem->pages, list) {
+		MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_SWAP);
+
+		/* free the page node and release the swap item, if the ref count is 1,
+		 * then need also free the swap item. */
+		list_del(&m_page->list);
+		if (1 == _mali_page_node_get_ref_count(m_page)) {
+			free_pages_nr++;
+		}
+
+		_mali_mem_swap_page_node_free(m_page);
+	}
+
+	return free_pages_nr;
+}
+
+static u32 mali_mem_swap_cow_free(mali_mem_cow *cow_mem)
+{
+	struct mali_page_node *m_page, *m_tmp;
+	u32 free_pages_nr = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(cow_mem);
+
+	list_for_each_entry_safe(m_page, m_tmp, &cow_mem->pages, list) {
+		MALI_DEBUG_ASSERT(m_page->type == MALI_PAGE_NODE_SWAP);
+
+		/* free the page node and release the swap item, if the ref count is 1,
+		 * then need also free the swap item. */
+		list_del(&m_page->list);
+		if (1 == _mali_page_node_get_ref_count(m_page)) {
+			free_pages_nr++;
+		}
+
+		_mali_mem_swap_page_node_free(m_page);
+	}
+
+	return free_pages_nr;
+}
+
+u32 mali_mem_swap_release(mali_mem_backend *mem_bkend, mali_bool is_mali_mapped)
+{
+	mali_mem_allocation *alloc;
+	u32 free_pages_nr = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(mem_bkend);
+	alloc = mem_bkend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	if (is_mali_mapped) {
+		mali_mem_swap_mali_unmap(alloc);
+	}
+
+	mali_memory_swap_list_backend_delete(mem_bkend);
+
+	mutex_lock(&mem_bkend->mutex);
+	/* To make sure the given memory backend was unlocked from Mali side,
+	 * and then free this memory block. */
+	mali_mem_swap_unlock_single_mem_backend(mem_bkend);
+	mutex_unlock(&mem_bkend->mutex);
+
+	if (MALI_MEM_SWAP == mem_bkend->type) {
+		free_pages_nr = mali_mem_swap_free(&mem_bkend->swap_mem);
+	} else {
+		free_pages_nr = mali_mem_swap_cow_free(&mem_bkend->cow_mem);
+	}
+
+	return free_pages_nr;
+}
+
+mali_bool mali_mem_swap_in_page_node(struct mali_page_node *page_node)
+{
+	MALI_DEBUG_ASSERT(NULL != page_node);
+
+	page_node->swap_it->page = shmem_read_mapping_page(global_swap_space, page_node->swap_it->idx);
+
+	if (IS_ERR(page_node->swap_it->page)) {
+		MALI_DEBUG_PRINT_ERROR(("SWAP Mem: failed to swap in page with index: %d.\n", page_node->swap_it->idx));
+		return MALI_FALSE;
+	}
+
+	/* Ensure page is flushed from CPU caches. */
+	page_node->swap_it->dma_addr = dma_map_page(&mali_platform_device->dev, page_node->swap_it->page,
+				       0, _MALI_OSK_MALI_PAGE_SIZE, DMA_TO_DEVICE);
+
+	return MALI_TRUE;
+}
+
+int mali_mem_swap_alloc_pages(mali_mem_swap *swap_mem, u32 size, u32 *bkend_idx)
+{
+	size_t page_count = PAGE_ALIGN(size) / PAGE_SIZE;
+	struct mali_page_node *m_page;
+	long system_free_size;
+	u32 i, index;
+	mali_bool ret;
+
+	MALI_DEBUG_ASSERT(NULL != swap_mem);
+	MALI_DEBUG_ASSERT(NULL != bkend_idx);
+	MALI_DEBUG_ASSERT(page_count <= MALI_SWAP_GLOBAL_SWAP_FILE_INDEX_RESERVE);
+
+	if (atomic_read(&mali_mem_os_allocator.allocated_pages) * _MALI_OSK_MALI_PAGE_SIZE + size > mali_mem_os_allocator.allocation_limit) {
+		MALI_DEBUG_PRINT(2, ("Mali Mem: Unable to allocate %u bytes. Currently allocated: %lu, max limit %lu\n",
+				     size,
+				     atomic_read(&mali_mem_os_allocator.allocated_pages) * _MALI_OSK_MALI_PAGE_SIZE,
+				     mali_mem_os_allocator.allocation_limit));
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	INIT_LIST_HEAD(&swap_mem->pages);
+	swap_mem->count = page_count;
+	index = mali_mem_swap_idx_range_alloc(page_count);
+
+	if (_MALI_OSK_BITMAP_INVALIDATE_INDEX == index) {
+		MALI_PRINT_ERROR(("Mali Swap: Failed to allocate continuous index for swappable Mali memory."));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	for (i = 0; i < page_count; i++) {
+		m_page = _mali_mem_swap_page_node_allocate();
+
+		if (NULL == m_page) {
+			MALI_DEBUG_PRINT_ERROR(("SWAP Mem: Failed to allocate mali page node."));
+			swap_mem->count = i;
+
+			mali_mem_swap_free(swap_mem);
+			mali_mem_swap_idx_range_free(index + i, page_count - i);
+			return _MALI_OSK_ERR_FAULT;
+		}
+
+		m_page->swap_it->idx = index + i;
+
+		ret = mali_mem_swap_in_page_node(m_page);
+
+		if (MALI_FALSE == ret) {
+			MALI_DEBUG_PRINT_ERROR(("SWAP Mem: Allocate new page from SHMEM file failed."));
+			_mali_mem_swap_page_node_free(m_page);
+			mali_mem_swap_idx_range_free(index + i + 1, page_count - i - 1);
+
+			swap_mem->count = i;
+			mali_mem_swap_free(swap_mem);
+			return _MALI_OSK_ERR_NOMEM;
+		}
+
+		list_add_tail(&m_page->list, &swap_mem->pages);
+	}
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+	system_free_size = global_zone_page_state(NR_FREE_PAGES) * PAGE_SIZE;
+#else
+	system_free_size = global_page_state(NR_FREE_PAGES) * PAGE_SIZE;
+#endif
+        
+	if ((system_free_size < mali_mem_swap_out_threshold_value)
+	    && (mem_backend_swapped_pool_size > (mali_mem_swap_out_threshold_value >> 2))
+	    && mali_utilization_enabled()) {
+		_mali_osk_wq_schedule_work(mali_mem_swap_out_workq);
+	}
+
+	*bkend_idx = index;
+	return 0;
+}
+
+void mali_mem_swap_mali_unmap(mali_mem_allocation *alloc)
+{
+	struct mali_session_data *session;
+
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	mali_session_memory_lock(session);
+	mali_mem_mali_map_free(session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+			       alloc->flags);
+	mali_session_memory_unlock(session);
+}
+
+
+/* Insert these pages from shmem to mali page table*/
+_mali_osk_errcode_t mali_mem_swap_mali_map(mali_mem_swap *swap_mem, struct mali_session_data *session, u32 vaddr, u32 props)
+{
+	struct mali_page_directory *pagedir = session->page_directory;
+	struct mali_page_node *m_page;
+	dma_addr_t phys;
+	u32 virt = vaddr;
+	u32 prop = props;
+
+	list_for_each_entry(m_page, &swap_mem->pages, list) {
+		MALI_DEBUG_ASSERT(NULL != m_page->swap_it->page);
+		phys = m_page->swap_it->dma_addr;
+
+		mali_mmu_pagedir_update(pagedir, virt, phys, MALI_MMU_PAGE_SIZE, prop);
+		virt += MALI_MMU_PAGE_SIZE;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+int mali_mem_swap_in_pages(struct mali_pp_job *job)
+{
+	u32 num_memory_cookies;
+	struct mali_session_data *session;
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_allocation *mali_alloc = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+	struct mali_page_node *m_page;
+	mali_bool swap_in_success = MALI_TRUE;
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	num_memory_cookies = mali_pp_job_num_memory_cookies(job);
+	session = mali_pp_job_get_session(job);
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	for (i = 0; i < num_memory_cookies; i++) {
+
+		u32 mali_addr  = mali_pp_job_get_memory_cookie(job, i);
+
+		mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_addr, 0);
+		if (NULL == mali_vma_node) {
+			job->memory_cookies[i] = MALI_SWAP_INVALIDATE_MALI_ADDRESS;
+			swap_in_success = MALI_FALSE;
+			MALI_PRINT_ERROR(("SWAP Mem: failed to find mali_vma_node through Mali address: 0x%08x.\n", mali_addr));
+			continue;
+		}
+
+		mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+		MALI_DEBUG_ASSERT(NULL != mali_alloc);
+
+		if (MALI_MEM_SWAP != mali_alloc->type &&
+		    MALI_MEM_COW != mali_alloc->type) {
+			continue;
+		}
+
+		/* Get backend memory & Map on GPU */
+		mutex_lock(&mali_idr_mutex);
+		mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle);
+		mutex_unlock(&mali_idr_mutex);
+		MALI_DEBUG_ASSERT(NULL != mem_bkend);
+
+		/* We neednot hold backend's lock here, race safe.*/
+		if ((MALI_MEM_COW == mem_bkend->type) &&
+		    (!(mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED))) {
+			continue;
+		}
+
+		mutex_lock(&mem_bkend->mutex);
+
+		/* When swap_in_success is MALI_FALSE, it means this job has memory backend that could not be swapped in,
+		 * and it will be aborted in mali scheduler, so here, we just mark those memory cookies which
+		 * should not be swapped out when delete job to invalide */
+		if (MALI_FALSE == swap_in_success) {
+			job->memory_cookies[i] = MALI_SWAP_INVALIDATE_MALI_ADDRESS;
+			mutex_unlock(&mem_bkend->mutex);
+			continue;
+		}
+
+		/* Before swap in, checking if this memory backend has been swapped in by the latest flushed jobs. */
+		++mem_bkend->using_count;
+
+		if (1 < mem_bkend->using_count) {
+			MALI_DEBUG_ASSERT(MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN != (MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN & mem_bkend->flags));
+			mutex_unlock(&mem_bkend->mutex);
+			continue;
+		}
+
+		if (MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN != (MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN & mem_bkend->flags)) {
+			mutex_unlock(&mem_bkend->mutex);
+			continue;
+		}
+
+
+		list_for_each_entry(m_page, &mem_bkend->swap_mem.pages, list) {
+			if (MALI_FALSE == mali_mem_swap_in_page_node(m_page)) {
+				/* Don't have enough memory to swap in page, so release pages have already been swapped
+				 * in and then mark this pp job to be fail. */
+				mali_mem_swap_unlock_partial_locked_mem_backend(mem_bkend, m_page);
+				swap_in_success = MALI_FALSE;
+				break;
+			}
+		}
+
+		if (swap_in_success) {
+#ifdef MALI_MEM_SWAP_TRACKING
+			mem_backend_swapped_unlock_size -= mem_bkend->size;
+#endif
+			_mali_osk_mutex_wait(session->memory_lock);
+			mali_mem_swap_mali_map(&mem_bkend->swap_mem, session, mali_alloc->mali_mapping.addr, mali_alloc->mali_mapping.properties);
+			_mali_osk_mutex_signal(session->memory_lock);
+
+			/* Remove the unlock flag from mem backend flags, mark this backend has been swapped in. */
+			mem_bkend->flags &= ~(MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN);
+			mutex_unlock(&mem_bkend->mutex);
+		} else {
+			--mem_bkend->using_count;
+			/* Marking that this backend is not swapped in, need not to be processed anymore. */
+			job->memory_cookies[i] = MALI_SWAP_INVALIDATE_MALI_ADDRESS;
+			mutex_unlock(&mem_bkend->mutex);
+		}
+	}
+
+	job->swap_status = swap_in_success ? MALI_SWAP_IN_SUCC : MALI_SWAP_IN_FAIL;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+int mali_mem_swap_out_pages(struct mali_pp_job *job)
+{
+	u32 num_memory_cookies;
+	struct mali_session_data *session;
+	struct mali_vma_node *mali_vma_node = NULL;
+	mali_mem_allocation *mali_alloc = NULL;
+	mali_mem_backend *mem_bkend = NULL;
+	int i;
+
+	MALI_DEBUG_ASSERT_POINTER(job);
+
+	num_memory_cookies = mali_pp_job_num_memory_cookies(job);
+	session = mali_pp_job_get_session(job);
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+
+	for (i = 0; i < num_memory_cookies; i++) {
+		u32 mali_addr  = mali_pp_job_get_memory_cookie(job, i);
+
+		if (MALI_SWAP_INVALIDATE_MALI_ADDRESS == mali_addr) {
+			continue;
+		}
+
+		mali_vma_node = mali_vma_offset_search(&session->allocation_mgr, mali_addr, 0);
+
+		if (NULL == mali_vma_node) {
+			MALI_PRINT_ERROR(("SWAP Mem: failed to find mali_vma_node through Mali address: 0x%08x.\n", mali_addr));
+			continue;
+		}
+
+		mali_alloc = container_of(mali_vma_node, struct mali_mem_allocation, mali_vma_node);
+		MALI_DEBUG_ASSERT(NULL != mali_alloc);
+
+		if (MALI_MEM_SWAP != mali_alloc->type &&
+		    MALI_MEM_COW != mali_alloc->type) {
+			continue;
+		}
+
+		mutex_lock(&mali_idr_mutex);
+		mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle);
+		mutex_unlock(&mali_idr_mutex);
+		MALI_DEBUG_ASSERT(NULL != mem_bkend);
+
+		/* We neednot hold backend's lock here, race safe.*/
+		if ((MALI_MEM_COW == mem_bkend->type) &&
+		    (!(mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED))) {
+			continue;
+		}
+
+		mutex_lock(&mem_bkend->mutex);
+
+		MALI_DEBUG_ASSERT(0 < mem_bkend->using_count);
+
+		/* Reducing the using_count of mem backend means less pp job are using this memory backend,
+		 * if this count get to zero, it means no pp job is using it now, could put it to swap out list. */
+		--mem_bkend->using_count;
+
+		if (0 < mem_bkend->using_count) {
+			mutex_unlock(&mem_bkend->mutex);
+			continue;
+		}
+		mutex_unlock(&mem_bkend->mutex);
+
+		mali_memory_swap_list_backend_add(mem_bkend);
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+int mali_mem_swap_allocate_page_on_demand(mali_mem_backend *mem_bkend, u32 offset, struct page **pagep)
+{
+	struct mali_page_node *m_page, *found_node = NULL;
+	struct page *found_page;
+	mali_mem_swap *swap = NULL;
+	mali_mem_cow *cow = NULL;
+	dma_addr_t dma_addr;
+	u32 i = 0;
+
+	if (MALI_MEM_SWAP == mem_bkend->type) {
+		swap = &mem_bkend->swap_mem;
+		list_for_each_entry(m_page, &swap->pages, list) {
+			if (i == offset) {
+				found_node = m_page;
+				break;
+			}
+			i++;
+		}
+	} else {
+		MALI_DEBUG_ASSERT(MALI_MEM_COW == mem_bkend->type);
+		MALI_DEBUG_ASSERT(MALI_MEM_BACKEND_FLAG_SWAP_COWED == (MALI_MEM_BACKEND_FLAG_SWAP_COWED & mem_bkend->flags));
+
+		cow = &mem_bkend->cow_mem;
+		list_for_each_entry(m_page, &cow->pages, list) {
+			if (i == offset) {
+				found_node = m_page;
+				break;
+			}
+			i++;
+		}
+	}
+
+	if (NULL == found_node) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	found_page = shmem_read_mapping_page(global_swap_space, found_node->swap_it->idx);
+
+	if (!IS_ERR(found_page)) {
+		lock_page(found_page);
+		dma_addr = dma_map_page(&mali_platform_device->dev, found_page,
+					0, _MALI_OSK_MALI_PAGE_SIZE, DMA_TO_DEVICE);
+		dma_unmap_page(&mali_platform_device->dev, dma_addr,
+			       _MALI_OSK_MALI_PAGE_SIZE, DMA_TO_DEVICE);
+
+		*pagep = found_page;
+	} else {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+int mali_mem_swap_cow_page_on_demand(mali_mem_backend *mem_bkend, u32 offset, struct page **pagep)
+{
+	struct mali_page_node *m_page, *found_node = NULL, *new_node = NULL;
+	mali_mem_cow *cow = NULL;
+	u32 i = 0;
+
+	MALI_DEBUG_ASSERT(MALI_MEM_COW == mem_bkend->type);
+	MALI_DEBUG_ASSERT(MALI_MEM_BACKEND_FLAG_SWAP_COWED == (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED));
+	MALI_DEBUG_ASSERT(MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN == (MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN & mem_bkend->flags));
+	MALI_DEBUG_ASSERT(!mali_memory_swap_backend_in_swapped_pool(mem_bkend));
+
+	cow = &mem_bkend->cow_mem;
+	list_for_each_entry(m_page, &cow->pages, list) {
+		if (i == offset) {
+			found_node = m_page;
+			break;
+		}
+		i++;
+	}
+
+	if (NULL == found_node) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	new_node = _mali_mem_swap_page_node_allocate();
+
+	if (NULL == new_node) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	new_node->swap_it->idx = mali_mem_swap_idx_alloc();
+
+	if (_MALI_OSK_BITMAP_INVALIDATE_INDEX == new_node->swap_it->idx) {
+		MALI_DEBUG_PRINT(1, ("Failed to allocate swap index in swap CoW on demand.\n"));
+		kfree(new_node->swap_it);
+		kfree(new_node);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	if (MALI_FALSE == mali_mem_swap_in_page_node(new_node)) {
+		_mali_mem_swap_page_node_free(new_node);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	/* swap in found node for copy in kernel. */
+	if (MALI_FALSE == mali_mem_swap_in_page_node(found_node)) {
+		mali_mem_swap_out_page_node(new_node);
+		_mali_mem_swap_page_node_free(new_node);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	_mali_mem_cow_copy_page(found_node, new_node);
+
+	list_replace(&found_node->list, &new_node->list);
+
+	if (1 != _mali_page_node_get_ref_count(found_node)) {
+		atomic_add(1, &mem_bkend->mali_allocation->session->mali_mem_allocated_pages);
+		if (atomic_read(&mem_bkend->mali_allocation->session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE > mem_bkend->mali_allocation->session->max_mali_mem_allocated_size) {
+			mem_bkend->mali_allocation->session->max_mali_mem_allocated_size = atomic_read(&mem_bkend->mali_allocation->session->mali_mem_allocated_pages) * MALI_MMU_PAGE_SIZE;
+		}
+		mem_bkend->cow_mem.change_pages_nr++;
+	}
+
+	mali_mem_swap_out_page_node(found_node);
+	_mali_mem_swap_page_node_free(found_node);
+
+	/* When swap in the new page node, we have called dma_map_page for this page.\n */
+	dma_unmap_page(&mali_platform_device->dev, new_node->swap_it->dma_addr,
+		       _MALI_OSK_MALI_PAGE_SIZE, DMA_TO_DEVICE);
+
+	lock_page(new_node->swap_it->page);
+
+	*pagep = new_node->swap_it->page;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+#ifdef MALI_MEM_SWAP_TRACKING
+void mali_mem_swap_tracking(u32 *swap_pool_size, u32 *unlock_size)
+{
+	*swap_pool_size = mem_backend_swapped_pool_size;
+	*unlock_size =  mem_backend_swapped_unlock_size;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_swap_alloc.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_swap_alloc.h
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_SWAP_ALLOC_H__
+#define __MALI_MEMORY_SWAP_ALLOC_H__
+
+#include "mali_osk.h"
+#include "mali_session.h"
+
+#include "mali_memory_types.h"
+#include "mali_pp_job.h"
+
+/**
+ * Initialize memory swapping module.
+ */
+_mali_osk_errcode_t mali_mem_swap_init(void);
+
+void mali_mem_swap_term(void);
+
+/**
+ * Return global share memory file to other modules.
+ */
+struct file *mali_mem_swap_get_global_swap_file(void);
+
+/**
+ * Unlock the given memory backend and pages in it could be swapped out by kernel.
+ */
+void mali_mem_swap_unlock_single_mem_backend(mali_mem_backend *mem_bkend);
+
+/**
+ * Remove the given memory backend from global swap list.
+ */
+void mali_memory_swap_list_backend_delete(mali_mem_backend *mem_bkend);
+
+/**
+ * Add the given memory backend to global swap list.
+ */
+void mali_memory_swap_list_backend_add(mali_mem_backend *mem_bkend);
+
+/**
+ * Allocate 1 index from bitmap used as page index in global swap file.
+ */
+u32 mali_mem_swap_idx_alloc(void);
+
+void mali_mem_swap_idx_free(u32 idx);
+
+/**
+ * Allocate a new swap item without page index.
+ */
+struct mali_swap_item *mali_mem_swap_alloc_swap_item(void);
+
+/**
+ * Free a swap item, truncate the corresponding space in page cache and free index of page.
+ */
+void mali_mem_swap_free_swap_item(mali_swap_item *swap_item);
+
+/**
+ * Allocate a page node with swap item.
+ */
+struct mali_page_node *_mali_mem_swap_page_node_allocate(void);
+
+/**
+ * Reduce the reference count of given page node and if return 0, just free this page node.
+ */
+_mali_osk_errcode_t _mali_mem_swap_put_page_node(struct mali_page_node *m_page);
+
+void _mali_mem_swap_page_node_free(struct mali_page_node *m_page);
+
+/**
+ * Free a swappable memory backend.
+ */
+u32 mali_mem_swap_free(mali_mem_swap *swap_mem);
+
+/**
+ * Ummap and free.
+ */
+u32 mali_mem_swap_release(mali_mem_backend *mem_bkend, mali_bool is_mali_mapped);
+
+/**
+ * Read in a page from global swap file with the pre-allcated page index.
+ */
+mali_bool mali_mem_swap_in_page_node(struct mali_page_node *page_node);
+
+int mali_mem_swap_alloc_pages(mali_mem_swap *swap_mem, u32 size, u32 *bkend_idx);
+
+_mali_osk_errcode_t mali_mem_swap_mali_map(mali_mem_swap *swap_mem, struct mali_session_data *session, u32 vaddr, u32 props);
+
+void mali_mem_swap_mali_unmap(mali_mem_allocation *alloc);
+
+/**
+ * When pp job created, we need swap in all of memory backend needed by this pp job.
+ */
+int mali_mem_swap_in_pages(struct mali_pp_job *job);
+
+/**
+ * Put all of memory backends used this pp job to the global swap list.
+ */
+int mali_mem_swap_out_pages(struct mali_pp_job *job);
+
+/**
+ * This will be called in page fault to process CPU read&write.
+ */
+int mali_mem_swap_allocate_page_on_demand(mali_mem_backend *mem_bkend, u32 offset, struct page **pagep) ;
+
+/**
+ * Used to process cow on demand for swappable memory backend.
+ */
+int mali_mem_swap_cow_page_on_demand(mali_mem_backend *mem_bkend, u32 offset, struct page **pagep);
+
+#ifdef MALI_MEM_SWAP_TRACKING
+void mali_mem_swap_tracking(u32 *swap_pool_size, u32 *unlock_size);
+#endif
+#endif /* __MALI_MEMORY_SWAP_ALLOC_H__ */
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_types.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_types.h
@@ -0,0 +1,219 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_TYPES_H__
+#define __MALI_MEMORY_TYPES_H__
+
+#include <linux/mm.h>
+
+#if defined(CONFIG_MALI400_UMP)
+#include "ump_kernel_interface.h"
+#endif
+
+typedef u32 mali_address_t;
+
+typedef enum mali_mem_type {
+	MALI_MEM_OS,
+	MALI_MEM_EXTERNAL,
+	MALI_MEM_SWAP,
+	MALI_MEM_DMA_BUF,
+	MALI_MEM_UMP,
+	MALI_MEM_BLOCK,
+	MALI_MEM_COW,
+	MALI_MEM_SECURE,
+	MALI_MEM_TYPE_MAX,
+} mali_mem_type;
+
+typedef struct mali_block_item {
+	/* for block type, the block_phy is alway page size align
+	* so use low 12bit used for ref_cout.
+	*/
+	unsigned long phy_addr;
+} mali_block_item;
+
+/**
+ * idx is used to locate the given page in the address space of swap file.
+ * ref_count is used to mark how many memory backends are using this item.
+ */
+typedef struct mali_swap_item {
+	u32 idx;
+	atomic_t ref_count;
+	struct page *page;
+	dma_addr_t dma_addr;
+} mali_swap_item;
+
+typedef enum mali_page_node_type {
+	MALI_PAGE_NODE_OS,
+	MALI_PAGE_NODE_BLOCK,
+	MALI_PAGE_NODE_SWAP,
+} mali_page_node_type;
+
+typedef struct mali_page_node {
+	struct list_head list;
+	union {
+		struct page *page;
+		mali_block_item *blk_it; /*pointer to block item*/
+		mali_swap_item *swap_it;
+	};
+
+	u32 type;
+} mali_page_node;
+
+typedef struct mali_mem_os_mem {
+	struct list_head pages;
+	u32 count;
+} mali_mem_os_mem;
+
+typedef struct mali_mem_dma_buf {
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+	struct mali_dma_buf_attachment *attachment;
+#endif
+} mali_mem_dma_buf;
+
+typedef struct mali_mem_external {
+	dma_addr_t phys;
+	u32 size;
+} mali_mem_external;
+
+typedef struct mali_mem_ump {
+#if defined(CONFIG_MALI400_UMP)
+	ump_dd_handle handle;
+#endif
+} mali_mem_ump;
+
+typedef struct block_allocator_allocation {
+	/* The list will be released in reverse order */
+	struct block_info *last_allocated;
+	u32 mapping_length;
+	struct block_allocator *info;
+} block_allocator_allocation;
+
+typedef struct mali_mem_block_mem {
+	struct list_head pfns;
+	u32 count;
+} mali_mem_block_mem;
+
+typedef struct mali_mem_virt_mali_mapping {
+	mali_address_t addr; /* Virtual Mali address */
+	u32 properties;      /* MMU Permissions + cache, must match MMU HW */
+} mali_mem_virt_mali_mapping;
+
+typedef struct mali_mem_virt_cpu_mapping {
+	void __user *addr;
+	struct vm_area_struct *vma;
+} mali_mem_virt_cpu_mapping;
+
+#define MALI_MEM_ALLOCATION_VALID_MAGIC 0xdeda110c
+#define MALI_MEM_ALLOCATION_FREED_MAGIC 0x10101010
+
+typedef struct mali_mm_node {
+	/* MALI GPU vaddr start, use u32 for mmu only support 32bit address*/
+	uint32_t start; /* GPU vaddr */
+	uint32_t size;  /* GPU allocation virtual size */
+	unsigned allocated : 1;
+} mali_mm_node;
+
+typedef struct mali_vma_node {
+	struct mali_mm_node vm_node;
+	struct rb_node vm_rb;
+} mali_vma_node;
+
+
+typedef struct mali_mem_allocation {
+	MALI_DEBUG_CODE(u32 magic);
+	mali_mem_type type;                /**< Type of memory */
+	u32 flags;                         /**< Flags for this allocation */
+
+	struct mali_session_data *session; /**< Pointer to session that owns the allocation */
+
+	mali_mem_virt_cpu_mapping cpu_mapping; /**< CPU mapping */
+	mali_mem_virt_mali_mapping mali_mapping; /**< Mali mapping */
+
+	/* add for new memory system */
+	struct mali_vma_node mali_vma_node;
+	u32 vsize; /* virtual size*/
+	u32 psize; /* physical backend memory size*/
+	struct list_head list;
+	s32 backend_handle; /* idr for mem_backend */
+	_mali_osk_atomic_t mem_alloc_refcount;
+} mali_mem_allocation;
+
+struct mali_mem_os_allocator {
+	spinlock_t pool_lock;
+	struct list_head pool_pages;
+	size_t pool_count;
+
+	atomic_t allocated_pages;
+	size_t allocation_limit;
+
+	struct shrinker shrinker;
+	struct delayed_work timed_shrinker;
+	struct workqueue_struct *wq;
+};
+
+/* COW backend memory type */
+typedef struct mali_mem_cow {
+	struct list_head pages;  /**< all pages for this cow backend allocation,
+                                                                including new allocated pages for modified range*/
+	u32 count;               /**< number of pages */
+	s32 change_pages_nr;
+} mali_mem_cow;
+
+typedef struct mali_mem_swap {
+	struct list_head pages;
+	u32 count;
+} mali_mem_swap;
+
+typedef struct mali_mem_secure {
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+	struct dma_buf *buf;
+	struct dma_buf_attachment *attachment;
+	struct sg_table *sgt;
+#endif
+	u32 count;
+} mali_mem_secure;
+
+#define MALI_MEM_BACKEND_FLAG_COWED                   (0x1)  /* COW has happen on this backend */
+#define MALI_MEM_BACKEND_FLAG_COW_CPU_NO_WRITE        (0x2)  /* This is an COW backend, mapped as not allowed cpu to write */
+#define MALI_MEM_BACKEND_FLAG_SWAP_COWED              (0x4)  /* Mark the given backend is cowed from swappable memory. */
+/* Mark this backend is not swapped_in in MALI driver, and before using it,
+ * we should swap it in and set up corresponding page table. */
+#define MALI_MEM_BACKEND_FLAG_UNSWAPPED_IN            (0x8)
+#define MALI_MEM_BACKEND_FLAG_NOT_BINDED              (0x1 << 5) /* this backend it not back with physical memory, used for defer bind */
+#define MALI_MEM_BACKEND_FLAG_BINDED              (0x1 << 6) /* this backend it back with physical memory, used for defer bind */
+
+typedef struct mali_mem_backend {
+	mali_mem_type type;                /**< Type of backend memory */
+	u32 flags;                         /**< Flags for this allocation */
+	u32 size;
+	/* Union selected by type. */
+	union {
+		mali_mem_os_mem os_mem;       /**< MALI_MEM_OS */
+		mali_mem_external ext_mem;    /**< MALI_MEM_EXTERNAL */
+		mali_mem_dma_buf dma_buf;     /**< MALI_MEM_DMA_BUF */
+		mali_mem_ump ump_mem;         /**< MALI_MEM_UMP */
+		mali_mem_block_mem block_mem; /**< MALI_MEM_BLOCK */
+		mali_mem_cow cow_mem;
+		mali_mem_swap swap_mem;
+		mali_mem_secure secure_mem;
+	};
+	mali_mem_allocation *mali_allocation;
+	struct mutex mutex;
+	mali_mem_type cow_type;
+
+	struct list_head list;           /**< Used to link swappable memory backend to the global swappable list */
+	int using_count;                 /**< Mark how many PP jobs are using this memory backend */
+	u32 start_idx;                   /**< If the correspondign vma of this backend is linear, this value will be used to set vma->vm_pgoff */
+} mali_mem_backend;
+
+#define MALI_MEM_FLAG_MALI_GUARD_PAGE (_MALI_MAP_EXTERNAL_MAP_GUARD_PAGE)
+#define MALI_MEM_FLAG_DONT_CPU_MAP    (1 << 1)
+#define MALI_MEM_FLAG_CAN_RESIZE  (_MALI_MEMORY_ALLOCATE_RESIZEABLE)
+#endif /* __MALI_MEMORY_TYPES__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_ump.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_ump.c
@@ -0,0 +1,154 @@
+/*
+ * Copyright (C) 2012-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_kernel_linux.h"
+#include "mali_memory.h"
+#include "ump_kernel_interface.h"
+
+static int mali_mem_ump_map(mali_mem_backend *mem_backend)
+{
+	ump_dd_handle ump_mem;
+	mali_mem_allocation *alloc;
+	struct mali_session_data *session;
+	u32 nr_blocks;
+	u32 i;
+	ump_dd_physical_block *ump_blocks;
+	struct mali_page_directory *pagedir;
+	u32 offset = 0;
+	_mali_osk_errcode_t err;
+
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_ASSERT(MALI_MEM_UMP == mem_backend->type);
+
+	alloc = mem_backend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	ump_mem = mem_backend->ump_mem.handle;
+	MALI_DEBUG_ASSERT(UMP_DD_HANDLE_INVALID != ump_mem);
+
+	nr_blocks = ump_dd_phys_block_count_get(ump_mem);
+	if (nr_blocks == 0) {
+		MALI_DEBUG_PRINT(1, ("No block count\n"));
+		return -EINVAL;
+	}
+
+	ump_blocks = _mali_osk_malloc(sizeof(*ump_blocks) * nr_blocks);
+	if (NULL == ump_blocks) {
+		return -ENOMEM;
+	}
+
+	if (UMP_DD_INVALID == ump_dd_phys_blocks_get(ump_mem, ump_blocks, nr_blocks)) {
+		_mali_osk_free(ump_blocks);
+		return -EFAULT;
+	}
+
+	pagedir = session->page_directory;
+
+	mali_session_memory_lock(session);
+
+	err = mali_mem_mali_map_prepare(alloc);
+	if (_MALI_OSK_ERR_OK != err) {
+		MALI_DEBUG_PRINT(1, ("Mapping of UMP memory failed\n"));
+
+		_mali_osk_free(ump_blocks);
+		mali_session_memory_unlock(session);
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < nr_blocks; ++i) {
+		u32 virt = alloc->mali_vma_node.vm_node.start + offset;
+
+		MALI_DEBUG_PRINT(7, ("Mapping in 0x%08x size %d\n", ump_blocks[i].addr , ump_blocks[i].size));
+
+		mali_mmu_pagedir_update(pagedir, virt, ump_blocks[i].addr,
+					ump_blocks[i].size, MALI_MMU_FLAGS_DEFAULT);
+
+		offset += ump_blocks[i].size;
+	}
+
+	if (alloc->flags & _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE) {
+		u32 virt = alloc->mali_vma_node.vm_node.start + offset;
+
+		/* Map in an extra virtual guard page at the end of the VMA */
+		MALI_DEBUG_PRINT(6, ("Mapping in extra guard page\n"));
+
+		mali_mmu_pagedir_update(pagedir, virt, ump_blocks[0].addr, _MALI_OSK_MALI_PAGE_SIZE, MALI_MMU_FLAGS_DEFAULT);
+
+		offset += _MALI_OSK_MALI_PAGE_SIZE;
+	}
+	mali_session_memory_unlock(session);
+	_mali_osk_free(ump_blocks);
+	return 0;
+}
+
+static void mali_mem_ump_unmap(mali_mem_allocation *alloc)
+{
+	struct mali_session_data *session;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	session = alloc->session;
+	MALI_DEBUG_ASSERT_POINTER(session);
+	mali_session_memory_lock(session);
+	mali_mem_mali_map_free(session, alloc->psize, alloc->mali_vma_node.vm_node.start,
+			       alloc->flags);
+	mali_session_memory_unlock(session);
+}
+
+int mali_mem_bind_ump_buf(mali_mem_allocation *alloc, mali_mem_backend *mem_backend, u32  secure_id, u32 flags)
+{
+	ump_dd_handle ump_mem;
+	int ret;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_ASSERT(MALI_MEM_UMP == mem_backend->type);
+
+	MALI_DEBUG_PRINT(3,
+			 ("Requested to map ump memory with secure id %d into virtual memory 0x%08X, size 0x%08X\n",
+			  secure_id, alloc->mali_vma_node.vm_node.start, alloc->mali_vma_node.vm_node.size));
+
+	ump_mem = ump_dd_handle_create_from_secure_id(secure_id);
+	if (UMP_DD_HANDLE_INVALID == ump_mem) MALI_ERROR(_MALI_OSK_ERR_FAULT);
+	alloc->flags |= MALI_MEM_FLAG_DONT_CPU_MAP;
+	if (flags & _MALI_MAP_EXTERNAL_MAP_GUARD_PAGE) {
+		alloc->flags |= MALI_MEM_FLAG_MALI_GUARD_PAGE;
+	}
+
+	mem_backend->ump_mem.handle = ump_mem;
+
+	ret = mali_mem_ump_map(mem_backend);
+	if (0 != ret) {
+		ump_dd_reference_release(ump_mem);
+		return _MALI_OSK_ERR_FAULT;
+	}
+	MALI_DEBUG_PRINT(3, ("Returning from UMP bind\n"));
+	return _MALI_OSK_ERR_OK;
+}
+
+void mali_mem_unbind_ump_buf(mali_mem_backend *mem_backend)
+{
+	ump_dd_handle ump_mem;
+	mali_mem_allocation *alloc;
+	MALI_DEBUG_ASSERT_POINTER(mem_backend);
+	MALI_DEBUG_ASSERT(MALI_MEM_UMP == mem_backend->type);
+	ump_mem = mem_backend->ump_mem.handle;
+	MALI_DEBUG_ASSERT(UMP_DD_HANDLE_INVALID != ump_mem);
+
+	alloc = mem_backend->mali_allocation;
+	MALI_DEBUG_ASSERT_POINTER(alloc);
+	mali_mem_ump_unmap(alloc);
+	ump_dd_reference_release(ump_mem);
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_ump.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_ump.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2011-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_UMP_BUF_H__
+#define __MALI_MEMORY_UMP_BUF_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "mali_uk_types.h"
+#include "mali_osk.h"
+#include "mali_memory.h"
+
+int mali_mem_bind_ump_buf(mali_mem_allocation *alloc, mali_mem_backend *mem_backend, u32  secure_id, u32 flags);
+void mali_mem_unbind_ump_buf(mali_mem_backend *mem_backend);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_MEMORY_DMA_BUF_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_util.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_util.c
@@ -0,0 +1,161 @@
+/*
+ * Copyright (C) 2013-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_kernel_linux.h"
+#include "mali_scheduler.h"
+
+#include "mali_memory.h"
+#include "mali_memory_os_alloc.h"
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+#include "mali_memory_dma_buf.h"
+#include "mali_memory_secure.h"
+#endif
+#if defined(CONFIG_MALI400_UMP)
+#include "mali_memory_ump.h"
+#endif
+#include "mali_memory_external.h"
+#include "mali_memory_manager.h"
+#include "mali_memory_virtual.h"
+#include "mali_memory_cow.h"
+#include "mali_memory_block_alloc.h"
+#include "mali_memory_swap_alloc.h"
+
+
+
+/**
+*function @_mali_free_allocation_mem - free a memory allocation
+*/
+static u32 _mali_free_allocation_mem(mali_mem_allocation *mali_alloc)
+{
+	mali_mem_backend *mem_bkend = NULL;
+	u32 free_pages_nr = 0;
+
+	struct mali_session_data *session = mali_alloc->session;
+	MALI_DEBUG_PRINT(4, (" _mali_free_allocation_mem, psize =0x%x! \n", mali_alloc->psize));
+	if (0 == mali_alloc->psize)
+		goto out;
+
+	/* Get backend memory & Map on CPU */
+	mutex_lock(&mali_idr_mutex);
+	mem_bkend = idr_find(&mali_backend_idr, mali_alloc->backend_handle);
+	mutex_unlock(&mali_idr_mutex);
+	MALI_DEBUG_ASSERT(NULL != mem_bkend);
+
+	switch (mem_bkend->type) {
+	case MALI_MEM_OS:
+		free_pages_nr = mali_mem_os_release(mem_bkend);
+		atomic_sub(free_pages_nr, &session->mali_mem_allocated_pages);
+		break;
+	case MALI_MEM_UMP:
+#if defined(CONFIG_MALI400_UMP)
+		mali_mem_unbind_ump_buf(mem_bkend);
+		atomic_sub(mem_bkend->size / MALI_MMU_PAGE_SIZE, &session->mali_mem_array[mem_bkend->type]);
+#else
+		MALI_DEBUG_PRINT(1, ("UMP not supported\n"));
+#endif
+		break;
+	case MALI_MEM_DMA_BUF:
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+		mali_mem_unbind_dma_buf(mem_bkend);
+		atomic_sub(mem_bkend->size / MALI_MMU_PAGE_SIZE, &session->mali_mem_array[mem_bkend->type]);
+#else
+		MALI_DEBUG_PRINT(1, ("DMA not supported\n"));
+#endif
+		break;
+	case MALI_MEM_EXTERNAL:
+		mali_mem_unbind_ext_buf(mem_bkend);
+		atomic_sub(mem_bkend->size / MALI_MMU_PAGE_SIZE, &session->mali_mem_array[mem_bkend->type]);
+		break;
+
+	case MALI_MEM_BLOCK:
+		free_pages_nr = mali_mem_block_release(mem_bkend);
+		atomic_sub(free_pages_nr, &session->mali_mem_allocated_pages);
+		break;
+
+	case MALI_MEM_COW:
+		if (mem_bkend->flags & MALI_MEM_BACKEND_FLAG_SWAP_COWED) {
+			free_pages_nr = mali_mem_swap_release(mem_bkend, MALI_TRUE);
+		} else {
+			free_pages_nr = mali_mem_cow_release(mem_bkend, MALI_TRUE);
+		}
+		atomic_sub(free_pages_nr, &session->mali_mem_allocated_pages);
+		break;
+	case MALI_MEM_SWAP:
+		free_pages_nr = mali_mem_swap_release(mem_bkend, MALI_TRUE);
+		atomic_sub(free_pages_nr, &session->mali_mem_allocated_pages);
+		atomic_sub(free_pages_nr, &session->mali_mem_array[mem_bkend->type]);
+		break;
+	case MALI_MEM_SECURE:
+#if defined(CONFIG_DMA_SHARED_BUFFER)
+		free_pages_nr = mali_mem_secure_release(mem_bkend);
+		atomic_sub(free_pages_nr, &session->mali_mem_allocated_pages);
+#else
+		MALI_DEBUG_PRINT(1, ("DMA not supported for mali secure memory\n"));
+#endif
+		break;
+	default:
+		MALI_DEBUG_PRINT(1, ("mem type %d is not in the mali_mem_type enum.\n", mem_bkend->type));
+		break;
+	}
+
+	if ((NULL != mali_alloc->cpu_mapping.vma) && (mali_alloc == (mali_alloc->cpu_mapping.vma)->vm_private_data))
+		(mali_alloc->cpu_mapping.vma)->vm_private_data = NULL;
+
+	/*Remove backend memory idex */
+	mutex_lock(&mali_idr_mutex);
+	idr_remove(&mali_backend_idr, mali_alloc->backend_handle);
+	mutex_unlock(&mali_idr_mutex);
+	kfree(mem_bkend);
+out:
+	/* remove memory allocation  */
+	mali_vma_offset_remove(&session->allocation_mgr, &mali_alloc->mali_vma_node);
+	mali_mem_allocation_struct_destory(mali_alloc);
+	return free_pages_nr;
+}
+
+/**
+*  ref_count for allocation
+*/
+u32 mali_allocation_unref(struct mali_mem_allocation **alloc)
+{
+	u32 free_pages_nr = 0;
+	mali_mem_allocation *mali_alloc = *alloc;
+	*alloc = NULL;
+	if (0 == _mali_osk_atomic_dec_return(&mali_alloc->mem_alloc_refcount)) {
+		free_pages_nr = _mali_free_allocation_mem(mali_alloc);
+	}
+	return free_pages_nr;
+}
+
+void mali_allocation_ref(struct mali_mem_allocation *alloc)
+{
+	_mali_osk_atomic_inc(&alloc->mem_alloc_refcount);
+}
+
+void mali_free_session_allocations(struct mali_session_data *session)
+{
+	struct mali_mem_allocation *entry, *next;
+
+	MALI_DEBUG_PRINT(4, (" mali_free_session_allocations! \n"));
+
+	list_for_each_entry_safe(entry, next, &session->allocation_mgr.head, list) {
+		mali_allocation_unref(&entry);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_util.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_util.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_MEMORY_UTIL_H__
+#define __MALI_MEMORY_UTIL_H__
+
+u32 mali_allocation_unref(struct mali_mem_allocation **alloc);
+
+void mali_allocation_ref(struct mali_mem_allocation *alloc);
+
+void mali_free_session_allocations(struct mali_session_data *session);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_virtual.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_virtual.c
@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/mm_types.h>
+#include <linux/fs.h>
+#include <linux/dma-mapping.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_kernel_linux.h"
+#include "mali_scheduler.h"
+#include "mali_memory_os_alloc.h"
+#include "mali_memory_manager.h"
+#include "mali_memory_virtual.h"
+
+
+/**
+*internal helper to link node into the rb-tree
+*/
+static inline void _mali_vma_offset_add_rb(struct mali_allocation_manager *mgr,
+		struct mali_vma_node *node)
+{
+	struct rb_node **iter = &mgr->allocation_mgr_rb.rb_node;
+	struct rb_node *parent = NULL;
+	struct mali_vma_node *iter_node;
+
+	while (likely(*iter)) {
+		parent = *iter;
+		iter_node = rb_entry(*iter, struct mali_vma_node, vm_rb);
+
+		if (node->vm_node.start < iter_node->vm_node.start)
+			iter = &(*iter)->rb_left;
+		else if (node->vm_node.start > iter_node->vm_node.start)
+			iter = &(*iter)->rb_right;
+		else
+			MALI_DEBUG_ASSERT(0);
+	}
+
+	rb_link_node(&node->vm_rb, parent, iter);
+	rb_insert_color(&node->vm_rb, &mgr->allocation_mgr_rb);
+}
+
+/**
+ * mali_vma_offset_add() - Add offset node to RB Tree
+ */
+int mali_vma_offset_add(struct mali_allocation_manager *mgr,
+			struct mali_vma_node *node)
+{
+	int ret = 0;
+	write_lock(&mgr->vm_lock);
+
+	if (node->vm_node.allocated) {
+		goto out;
+	}
+
+	_mali_vma_offset_add_rb(mgr, node);
+	/* set to allocated */
+	node->vm_node.allocated = 1;
+
+out:
+	write_unlock(&mgr->vm_lock);
+	return ret;
+}
+
+/**
+ * mali_vma_offset_remove() - Remove offset node from RB tree
+ */
+void mali_vma_offset_remove(struct mali_allocation_manager *mgr,
+			    struct mali_vma_node *node)
+{
+	write_lock(&mgr->vm_lock);
+
+	if (node->vm_node.allocated) {
+		rb_erase(&node->vm_rb, &mgr->allocation_mgr_rb);
+		memset(&node->vm_node, 0, sizeof(node->vm_node));
+	}
+	write_unlock(&mgr->vm_lock);
+}
+
+/**
+* mali_vma_offset_search - Search the node in RB tree
+*/
+struct mali_vma_node *mali_vma_offset_search(struct mali_allocation_manager *mgr,
+		unsigned long start, unsigned long pages)
+{
+	struct mali_vma_node *node, *best;
+	struct rb_node *iter;
+	unsigned long offset;
+	read_lock(&mgr->vm_lock);
+
+	iter = mgr->allocation_mgr_rb.rb_node;
+	best = NULL;
+
+	while (likely(iter)) {
+		node = rb_entry(iter, struct mali_vma_node, vm_rb);
+		offset = node->vm_node.start;
+		if (start >= offset) {
+			iter = iter->rb_right;
+			best = node;
+			if (start == offset)
+				break;
+		} else {
+			iter = iter->rb_left;
+		}
+	}
+
+	if (best) {
+		offset = best->vm_node.start + best->vm_node.size;
+		if (offset <= start + pages)
+			best = NULL;
+	}
+	read_unlock(&mgr->vm_lock);
+
+	return best;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_memory_virtual.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_memory_virtual.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#ifndef __MALI_GPU_VMEM_H__
+#define __MALI_GPU_VMEM_H__
+
+#include "mali_osk.h"
+#include "mali_session.h"
+#include <linux/list.h>
+#include <linux/mm.h>
+#include <linux/rbtree.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include "mali_memory_types.h"
+#include "mali_memory_os_alloc.h"
+#include "mali_memory_manager.h"
+
+
+
+int mali_vma_offset_add(struct mali_allocation_manager *mgr,
+			struct mali_vma_node *node);
+
+void mali_vma_offset_remove(struct mali_allocation_manager *mgr,
+			    struct mali_vma_node *node);
+
+struct mali_vma_node *mali_vma_offset_search(struct mali_allocation_manager *mgr,
+		unsigned long start,    unsigned long pages);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_atomics.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_atomics.c
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2010, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_atomics.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include "mali_osk.h"
+#include <asm/atomic.h>
+#include "mali_kernel_common.h"
+
+void _mali_osk_atomic_dec(_mali_osk_atomic_t *atom)
+{
+	atomic_dec((atomic_t *)&atom->u.val);
+}
+
+u32 _mali_osk_atomic_dec_return(_mali_osk_atomic_t *atom)
+{
+	return atomic_dec_return((atomic_t *)&atom->u.val);
+}
+
+void _mali_osk_atomic_inc(_mali_osk_atomic_t *atom)
+{
+	atomic_inc((atomic_t *)&atom->u.val);
+}
+
+u32 _mali_osk_atomic_inc_return(_mali_osk_atomic_t *atom)
+{
+	return atomic_inc_return((atomic_t *)&atom->u.val);
+}
+
+void _mali_osk_atomic_init(_mali_osk_atomic_t *atom, u32 val)
+{
+	MALI_DEBUG_ASSERT_POINTER(atom);
+	atomic_set((atomic_t *)&atom->u.val, val);
+}
+
+u32 _mali_osk_atomic_read(_mali_osk_atomic_t *atom)
+{
+	return atomic_read((atomic_t *)&atom->u.val);
+}
+
+void _mali_osk_atomic_term(_mali_osk_atomic_t *atom)
+{
+	MALI_IGNORE(atom);
+}
+
+u32 _mali_osk_atomic_xchg(_mali_osk_atomic_t *atom, u32 val)
+{
+	return atomic_xchg((atomic_t *)&atom->u.val, val);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_bitmap.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_bitmap.c
@@ -0,0 +1,152 @@
+/*
+ * Copyright (C) 2010, 2013-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_bitmap.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/bitmap.h>
+#include <linux/vmalloc.h>
+#include "common/mali_kernel_common.h"
+#include "mali_osk_types.h"
+#include "mali_osk.h"
+
+u32 _mali_osk_bitmap_alloc(struct _mali_osk_bitmap *bitmap)
+{
+	u32 obj;
+
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+
+	_mali_osk_spinlock_lock(bitmap->lock);
+
+	obj = find_next_zero_bit(bitmap->table, bitmap->max, bitmap->reserve);
+
+	if (obj < bitmap->max) {
+		set_bit(obj, bitmap->table);
+	} else {
+		obj = -1;
+	}
+
+	if (obj != -1)
+		--bitmap->avail;
+	_mali_osk_spinlock_unlock(bitmap->lock);
+
+	return obj;
+}
+
+void _mali_osk_bitmap_free(struct _mali_osk_bitmap *bitmap, u32 obj)
+{
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+
+	_mali_osk_bitmap_free_range(bitmap, obj, 1);
+}
+
+u32 _mali_osk_bitmap_alloc_range(struct _mali_osk_bitmap *bitmap, int cnt)
+{
+	u32 obj;
+
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+
+	if (0 >= cnt) {
+		return -1;
+	}
+
+	if (1 == cnt) {
+		return _mali_osk_bitmap_alloc(bitmap);
+	}
+
+	_mali_osk_spinlock_lock(bitmap->lock);
+	obj = bitmap_find_next_zero_area(bitmap->table, bitmap->max,
+					 bitmap->last, cnt, 0);
+
+	if (obj >= bitmap->max) {
+		obj = bitmap_find_next_zero_area(bitmap->table, bitmap->max,
+						 bitmap->reserve, cnt, 0);
+	}
+
+	if (obj < bitmap->max) {
+		bitmap_set(bitmap->table, obj, cnt);
+
+		bitmap->last = (obj + cnt);
+		if (bitmap->last >= bitmap->max) {
+			bitmap->last = bitmap->reserve;
+		}
+	} else {
+		obj = -1;
+	}
+
+	if (obj != -1) {
+		bitmap->avail -= cnt;
+	}
+
+	_mali_osk_spinlock_unlock(bitmap->lock);
+
+	return obj;
+}
+
+u32 _mali_osk_bitmap_avail(struct _mali_osk_bitmap *bitmap)
+{
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+
+	return bitmap->avail;
+}
+
+void _mali_osk_bitmap_free_range(struct _mali_osk_bitmap *bitmap, u32 obj, int cnt)
+{
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+
+	_mali_osk_spinlock_lock(bitmap->lock);
+	bitmap_clear(bitmap->table, obj, cnt);
+	bitmap->last = min(bitmap->last, obj);
+
+	bitmap->avail += cnt;
+	_mali_osk_spinlock_unlock(bitmap->lock);
+}
+
+int _mali_osk_bitmap_init(struct _mali_osk_bitmap *bitmap, u32 num, u32 reserve)
+{
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+	MALI_DEBUG_ASSERT(reserve <= num);
+
+	bitmap->reserve = reserve;
+	bitmap->last = reserve;
+	bitmap->max  = num;
+	bitmap->avail = num - reserve;
+	bitmap->lock = _mali_osk_spinlock_init(_MALI_OSK_LOCKFLAG_UNORDERED, _MALI_OSK_LOCK_ORDER_FIRST);
+	if (!bitmap->lock) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+	bitmap->table = kzalloc(BITS_TO_LONGS(bitmap->max) *
+				sizeof(long), GFP_KERNEL);
+	if (!bitmap->table) {
+		_mali_osk_spinlock_term(bitmap->lock);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void _mali_osk_bitmap_term(struct _mali_osk_bitmap *bitmap)
+{
+	MALI_DEBUG_ASSERT_POINTER(bitmap);
+
+	if (NULL != bitmap->lock) {
+		_mali_osk_spinlock_term(bitmap->lock);
+	}
+
+	if (NULL != bitmap->table) {
+		kfree(bitmap->table);
+	}
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_irq.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_irq.c
@@ -0,0 +1,200 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_irq.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include <linux/slab.h> /* For memory allocation */
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/sched.h>
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+typedef struct _mali_osk_irq_t_struct {
+	u32 irqnum;
+	void *data;
+	_mali_osk_irq_uhandler_t uhandler;
+} mali_osk_irq_object_t;
+
+typedef irqreturn_t (*irq_handler_func_t)(int, void *, struct pt_regs *);
+static irqreturn_t irq_handler_upper_half(int port_name, void *dev_id);   /* , struct pt_regs *regs*/
+
+#if defined(DEBUG)
+
+struct test_interrupt_data {
+	_mali_osk_irq_ack_t ack_func;
+	void *probe_data;
+	mali_bool interrupt_received;
+	wait_queue_head_t wq;
+};
+
+static irqreturn_t test_interrupt_upper_half(int port_name, void *dev_id)
+{
+	irqreturn_t ret = IRQ_NONE;
+	struct test_interrupt_data *data = (struct test_interrupt_data *)dev_id;
+
+	if (_MALI_OSK_ERR_OK == data->ack_func(data->probe_data)) {
+		data->interrupt_received = MALI_TRUE;
+		wake_up(&data->wq);
+		ret = IRQ_HANDLED;
+	}
+
+	return ret;
+}
+
+static _mali_osk_errcode_t test_interrupt(u32 irqnum,
+		_mali_osk_irq_trigger_t trigger_func,
+		_mali_osk_irq_ack_t ack_func,
+		void *probe_data,
+		const char *description)
+{
+	unsigned long irq_flags = 0;
+	struct test_interrupt_data data = {
+		.ack_func = ack_func,
+		.probe_data = probe_data,
+		.interrupt_received = MALI_FALSE,
+	};
+
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	irq_flags |= IRQF_SHARED;
+#endif /* defined(CONFIG_MALI_SHARED_INTERRUPTS) */
+
+	if (0 != request_irq(irqnum, test_interrupt_upper_half, irq_flags, description, &data)) {
+		MALI_DEBUG_PRINT(2, ("Unable to install test IRQ handler for core '%s'\n", description));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	init_waitqueue_head(&data.wq);
+
+	trigger_func(probe_data);
+	wait_event_timeout(data.wq, data.interrupt_received, 100);
+
+	free_irq(irqnum, &data);
+
+	if (data.interrupt_received) {
+		MALI_DEBUG_PRINT(3, ("%s: Interrupt test OK\n", description));
+		return _MALI_OSK_ERR_OK;
+	} else {
+		MALI_PRINT_ERROR(("%s: Failed interrupt test on %u\n", description, irqnum));
+		return _MALI_OSK_ERR_FAULT;
+	}
+}
+
+#endif /* defined(DEBUG) */
+
+_mali_osk_irq_t *_mali_osk_irq_init(u32 irqnum, _mali_osk_irq_uhandler_t uhandler, void *int_data, _mali_osk_irq_trigger_t trigger_func, _mali_osk_irq_ack_t ack_func, void *probe_data, const char *description)
+{
+	mali_osk_irq_object_t *irq_object;
+	unsigned long irq_flags = 0;
+
+#if defined(CONFIG_MALI_SHARED_INTERRUPTS)
+	irq_flags |= IRQF_SHARED;
+#endif /* defined(CONFIG_MALI_SHARED_INTERRUPTS) */
+
+	irq_object = kmalloc(sizeof(mali_osk_irq_object_t), GFP_KERNEL);
+	if (NULL == irq_object) {
+		return NULL;
+	}
+
+	if (-1 == irqnum) {
+		/* Probe for IRQ */
+		if ((NULL != trigger_func) && (NULL != ack_func)) {
+			unsigned long probe_count = 3;
+			_mali_osk_errcode_t err;
+			int irq;
+
+			MALI_DEBUG_PRINT(2, ("Probing for irq\n"));
+
+			do {
+				unsigned long mask;
+
+				mask = probe_irq_on();
+				trigger_func(probe_data);
+
+				_mali_osk_time_ubusydelay(5);
+
+				irq = probe_irq_off(mask);
+				err = ack_func(probe_data);
+			} while (irq < 0 && (err == _MALI_OSK_ERR_OK) && probe_count--);
+
+			if (irq < 0 || (_MALI_OSK_ERR_OK != err)) irqnum = -1;
+			else irqnum = irq;
+		} else irqnum = -1; /* no probe functions, fault */
+
+		if (-1 != irqnum) {
+			/* found an irq */
+			MALI_DEBUG_PRINT(2, ("Found irq %d\n", irqnum));
+		} else {
+			MALI_DEBUG_PRINT(2, ("Probe for irq failed\n"));
+		}
+	}
+
+	irq_object->irqnum = irqnum;
+	irq_object->uhandler = uhandler;
+	irq_object->data = int_data;
+
+	if (-1 == irqnum) {
+		MALI_DEBUG_PRINT(2, ("No IRQ for core '%s' found during probe\n", description));
+		kfree(irq_object);
+		return NULL;
+	}
+
+#if defined(DEBUG)
+	/* Verify that the configured interrupt settings are working */
+	if (_MALI_OSK_ERR_OK != test_interrupt(irqnum, trigger_func, ack_func, probe_data, description)) {
+		MALI_DEBUG_PRINT(2, ("Test of IRQ(%d) handler for core '%s' failed\n", irqnum, description));
+		kfree(irq_object);
+		return NULL;
+	}
+#endif
+
+	if (0 != request_irq(irqnum, irq_handler_upper_half, irq_flags, description, irq_object)) {
+		MALI_DEBUG_PRINT(2, ("Unable to install IRQ handler for core '%s'\n", description));
+		kfree(irq_object);
+		return NULL;
+	}
+
+	return irq_object;
+}
+
+void _mali_osk_irq_term(_mali_osk_irq_t *irq)
+{
+	mali_osk_irq_object_t *irq_object = (mali_osk_irq_object_t *)irq;
+	free_irq(irq_object->irqnum, irq_object);
+	kfree(irq_object);
+}
+
+
+/** This function is called directly in interrupt context from the OS just after
+ * the CPU get the hw-irq from mali, or other devices on the same IRQ-channel.
+ * It is registered one of these function for each mali core. When an interrupt
+ * arrives this function will be called equal times as registered mali cores.
+ * That means that we only check one mali core in one function call, and the
+ * core we check for each turn is given by the \a dev_id variable.
+ * If we detect an pending interrupt on the given core, we mask the interrupt
+ * out by settging the core's IRQ_MASK register to zero.
+ * Then we schedule the mali_core_irq_handler_bottom_half to run as high priority
+ * work queue job.
+ */
+static irqreturn_t irq_handler_upper_half(int port_name, void *dev_id)   /* , struct pt_regs *regs*/
+{
+	irqreturn_t ret = IRQ_NONE;
+	mali_osk_irq_object_t *irq_object = (mali_osk_irq_object_t *)dev_id;
+
+	if (_MALI_OSK_ERR_OK == irq_object->uhandler(irq_object->data)) {
+		ret = IRQ_HANDLED;
+	}
+
+	return ret;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_locks.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_locks.c
@@ -0,0 +1,287 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_locks.c
+ * Implemenation of the OS abstraction layer for the kernel device driver
+ */
+
+#include "mali_osk_locks.h"
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+
+
+#ifdef DEBUG
+#ifdef LOCK_ORDER_CHECKING
+static DEFINE_SPINLOCK(lock_tracking_lock);
+static mali_bool add_lock_to_log_and_check(struct _mali_osk_lock_debug_s *lock, uint32_t tid);
+static void remove_lock_from_log(struct _mali_osk_lock_debug_s *lock, uint32_t tid);
+static const char *const lock_order_to_string(_mali_osk_lock_order_t order);
+#endif /* LOCK_ORDER_CHECKING */
+
+void _mali_osk_locks_debug_init(struct _mali_osk_lock_debug_s *checker, _mali_osk_lock_flags_t flags, _mali_osk_lock_order_t order)
+{
+	checker->orig_flags = flags;
+	checker->owner = 0;
+
+#ifdef LOCK_ORDER_CHECKING
+	checker->order = order;
+	checker->next = NULL;
+#endif
+}
+
+void _mali_osk_locks_debug_add(struct _mali_osk_lock_debug_s *checker)
+{
+	checker->owner = _mali_osk_get_tid();
+
+#ifdef LOCK_ORDER_CHECKING
+	if (!(checker->orig_flags & _MALI_OSK_LOCKFLAG_UNORDERED)) {
+		if (!add_lock_to_log_and_check(checker, _mali_osk_get_tid())) {
+			printk(KERN_ERR "%d: ERROR lock %p taken while holding a lock of a higher order.\n",
+			       _mali_osk_get_tid(), checker);
+			dump_stack();
+		}
+	}
+#endif
+}
+
+void _mali_osk_locks_debug_remove(struct _mali_osk_lock_debug_s *checker)
+{
+
+#ifdef LOCK_ORDER_CHECKING
+	if (!(checker->orig_flags & _MALI_OSK_LOCKFLAG_UNORDERED)) {
+		remove_lock_from_log(checker, _mali_osk_get_tid());
+	}
+#endif
+	checker->owner = 0;
+}
+
+
+#ifdef LOCK_ORDER_CHECKING
+/* Lock order checking
+ * -------------------
+ *
+ * To assure that lock ordering scheme defined by _mali_osk_lock_order_t is strictly adhered to, the
+ * following function will, together with a linked list and some extra members in _mali_osk_lock_debug_s,
+ * make sure that a lock that is taken has a higher order than the current highest-order lock a
+ * thread holds.
+ *
+ * This is done in the following manner:
+ * - A linked list keeps track of locks held by a thread.
+ * - A `next' pointer is added to each lock. This is used to chain the locks together.
+ * - When taking a lock, the `add_lock_to_log_and_check' makes sure that taking
+ *   the given lock is legal. It will follow the linked list  to find the last
+ *   lock taken by this thread. If the last lock's order was lower than the
+ *   lock that is to be taken, it appends the new lock to the list and returns
+ *   true, if not, it return false. This return value is assert()'ed on in
+ *   _mali_osk_lock_wait().
+ */
+
+static struct _mali_osk_lock_debug_s *lock_lookup_list;
+
+static void dump_lock_tracking_list(void)
+{
+	struct _mali_osk_lock_debug_s *l;
+	u32 n = 1;
+
+	/* print list for debugging purposes */
+	l = lock_lookup_list;
+
+	while (NULL != l) {
+		printk(" [lock: %p, tid_owner: %d, order: %d] ->", l, l->owner, l->order);
+		l = l->next;
+		MALI_DEBUG_ASSERT(n++ < 100);
+	}
+	printk(" NULL\n");
+}
+
+static int tracking_list_length(void)
+{
+	struct _mali_osk_lock_debug_s *l;
+	u32 n = 0;
+	l = lock_lookup_list;
+
+	while (NULL != l) {
+		l = l->next;
+		n++;
+		MALI_DEBUG_ASSERT(n < 100);
+	}
+	return n;
+}
+
+static mali_bool add_lock_to_log_and_check(struct _mali_osk_lock_debug_s *lock, uint32_t tid)
+{
+	mali_bool ret = MALI_FALSE;
+	_mali_osk_lock_order_t highest_order_for_tid = _MALI_OSK_LOCK_ORDER_FIRST;
+	struct _mali_osk_lock_debug_s *highest_order_lock = (struct _mali_osk_lock_debug_s *)0xbeefbabe;
+	struct _mali_osk_lock_debug_s *l;
+	unsigned long local_lock_flag;
+	u32 len;
+
+	spin_lock_irqsave(&lock_tracking_lock, local_lock_flag);
+	len = tracking_list_length();
+
+	l  = lock_lookup_list;
+	if (NULL == l) { /* This is the first lock taken by this thread -- record and return true */
+		lock_lookup_list = lock;
+		spin_unlock_irqrestore(&lock_tracking_lock, local_lock_flag);
+		return MALI_TRUE;
+	} else {
+		/* Traverse the locks taken and find the lock of the highest order.
+		 * Since several threads may hold locks, each lock's owner must be
+		 * checked so that locks not owned by this thread can be ignored. */
+		for (;;) {
+			MALI_DEBUG_ASSERT_POINTER(l);
+			if (tid == l->owner && l->order >= highest_order_for_tid) {
+				highest_order_for_tid = l->order;
+				highest_order_lock = l;
+			}
+
+			if (NULL != l->next) {
+				l = l->next;
+			} else {
+				break;
+			}
+		}
+
+		l->next = lock;
+		l->next = NULL;
+	}
+
+	/* We have now found the highest order lock currently held by this thread and can see if it is
+	 * legal to take the requested lock. */
+	ret = highest_order_for_tid < lock->order;
+
+	if (!ret) {
+		printk(KERN_ERR "Took lock of order %d (%s) while holding lock of order %d (%s)\n",
+		       lock->order, lock_order_to_string(lock->order),
+		       highest_order_for_tid, lock_order_to_string(highest_order_for_tid));
+		dump_lock_tracking_list();
+	}
+
+	if (len + 1 != tracking_list_length()) {
+		printk(KERN_ERR "************ lock: %p\n", lock);
+		printk(KERN_ERR "************ before: %d *** after: %d ****\n", len, tracking_list_length());
+		dump_lock_tracking_list();
+		MALI_DEBUG_ASSERT_POINTER(NULL);
+	}
+
+	spin_unlock_irqrestore(&lock_tracking_lock, local_lock_flag);
+	return ret;
+}
+
+static void remove_lock_from_log(struct _mali_osk_lock_debug_s *lock, uint32_t tid)
+{
+	struct _mali_osk_lock_debug_s *curr;
+	struct _mali_osk_lock_debug_s *prev = NULL;
+	unsigned long local_lock_flag;
+	u32 len;
+	u32 n = 0;
+
+	spin_lock_irqsave(&lock_tracking_lock, local_lock_flag);
+	len = tracking_list_length();
+	curr = lock_lookup_list;
+
+	if (NULL == curr) {
+		printk(KERN_ERR "Error: Lock tracking list was empty on call to remove_lock_from_log\n");
+		dump_lock_tracking_list();
+	}
+
+	MALI_DEBUG_ASSERT_POINTER(curr);
+
+
+	while (lock != curr) {
+		prev = curr;
+
+		MALI_DEBUG_ASSERT_POINTER(curr);
+		curr = curr->next;
+		MALI_DEBUG_ASSERT(n++ < 100);
+	}
+
+	if (NULL == prev) {
+		lock_lookup_list = curr->next;
+	} else {
+		MALI_DEBUG_ASSERT_POINTER(curr);
+		MALI_DEBUG_ASSERT_POINTER(prev);
+		prev->next = curr->next;
+	}
+
+	lock->next = NULL;
+
+	if (len - 1 != tracking_list_length()) {
+		printk(KERN_ERR "************ lock: %p\n", lock);
+		printk(KERN_ERR "************ before: %d *** after: %d ****\n", len, tracking_list_length());
+		dump_lock_tracking_list();
+		MALI_DEBUG_ASSERT_POINTER(NULL);
+	}
+
+	spin_unlock_irqrestore(&lock_tracking_lock, local_lock_flag);
+}
+
+static const char *const lock_order_to_string(_mali_osk_lock_order_t order)
+{
+	switch (order) {
+	case _MALI_OSK_LOCK_ORDER_SESSIONS:
+		return "_MALI_OSK_LOCK_ORDER_SESSIONS";
+		break;
+	case _MALI_OSK_LOCK_ORDER_MEM_SESSION:
+		return "_MALI_OSK_LOCK_ORDER_MEM_SESSION";
+		break;
+	case _MALI_OSK_LOCK_ORDER_MEM_INFO:
+		return "_MALI_OSK_LOCK_ORDER_MEM_INFO";
+		break;
+	case _MALI_OSK_LOCK_ORDER_MEM_PT_CACHE:
+		return "_MALI_OSK_LOCK_ORDER_MEM_PT_CACHE";
+		break;
+	case _MALI_OSK_LOCK_ORDER_DESCRIPTOR_MAP:
+		return "_MALI_OSK_LOCK_ORDER_DESCRIPTOR_MAP";
+		break;
+	case _MALI_OSK_LOCK_ORDER_PM_EXECUTION:
+		return "_MALI_OSK_LOCK_ORDER_PM_EXECUTION";
+		break;
+	case _MALI_OSK_LOCK_ORDER_EXECUTOR:
+		return "_MALI_OSK_LOCK_ORDER_EXECUTOR";
+		break;
+	case _MALI_OSK_LOCK_ORDER_TIMELINE_SYSTEM:
+		return "_MALI_OSK_LOCK_ORDER_TIMELINE_SYSTEM";
+		break;
+	case _MALI_OSK_LOCK_ORDER_SCHEDULER:
+		return "_MALI_OSK_LOCK_ORDER_SCHEDULER";
+		break;
+	case _MALI_OSK_LOCK_ORDER_SCHEDULER_DEFERRED:
+		return "_MALI_OSK_LOCK_ORDER_SCHEDULER_DEFERRED";
+		break;
+	case _MALI_OSK_LOCK_ORDER_DMA_COMMAND:
+		return "_MALI_OSK_LOCK_ORDER_DMA_COMMAND";
+		break;
+	case _MALI_OSK_LOCK_ORDER_PROFILING:
+		return "_MALI_OSK_LOCK_ORDER_PROFILING";
+		break;
+	case _MALI_OSK_LOCK_ORDER_L2:
+		return "_MALI_OSK_LOCK_ORDER_L2";
+		break;
+	case _MALI_OSK_LOCK_ORDER_L2_COMMAND:
+		return "_MALI_OSK_LOCK_ORDER_L2_COMMAND";
+		break;
+	case _MALI_OSK_LOCK_ORDER_UTILIZATION:
+		return "_MALI_OSK_LOCK_ORDER_UTILIZATION";
+		break;
+	case _MALI_OSK_LOCK_ORDER_SESSION_PENDING_JOBS:
+		return "_MALI_OSK_LOCK_ORDER_SESSION_PENDING_JOBS";
+		break;
+	case _MALI_OSK_LOCK_ORDER_PM_STATE:
+		return "_MALI_OSK_LOCK_ORDER_PM_STATE";
+		break;
+	default:
+		return "<UNKNOWN_LOCK_ORDER>";
+	}
+}
+#endif /* LOCK_ORDER_CHECKING */
+#endif /* DEBUG */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_locks.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_locks.h
@@ -0,0 +1,326 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_locks.h
+ * Defines OS abstraction of lock and mutex
+ */
+#ifndef _MALI_OSK_LOCKS_H
+#define _MALI_OSK_LOCKS_H
+
+#include <linux/spinlock.h>
+#include <linux/rwsem.h>
+#include <linux/mutex.h>
+
+#include <linux/slab.h>
+
+#include "mali_osk_types.h"
+
+#ifdef _cplusplus
+extern "C" {
+#endif
+
+	/* When DEBUG is enabled, this struct will be used to track owner, mode and order checking */
+#ifdef DEBUG
+	struct _mali_osk_lock_debug_s {
+		u32 owner;
+		_mali_osk_lock_flags_t orig_flags;
+		_mali_osk_lock_order_t order;
+		struct _mali_osk_lock_debug_s *next;
+	};
+#endif
+
+	/* Anstraction of spinlock_t */
+	struct _mali_osk_spinlock_s {
+#ifdef DEBUG
+		struct _mali_osk_lock_debug_s checker;
+#endif
+		spinlock_t spinlock;
+	};
+
+	/* Abstration of spinlock_t and lock flag which is used to store register's state before locking */
+	struct _mali_osk_spinlock_irq_s {
+#ifdef DEBUG
+		struct _mali_osk_lock_debug_s checker;
+#endif
+
+		spinlock_t spinlock;
+		unsigned long flags;
+	};
+
+	/* Abstraction of rw_semaphore in OS */
+	struct _mali_osk_mutex_rw_s {
+#ifdef DEBUG
+		struct _mali_osk_lock_debug_s checker;
+		_mali_osk_lock_mode_t mode;
+#endif
+
+		struct rw_semaphore rw_sema;
+	};
+
+	/* Mutex and mutex_interruptible functions share the same osk mutex struct */
+	struct _mali_osk_mutex_s {
+#ifdef DEBUG
+		struct _mali_osk_lock_debug_s checker;
+#endif
+		struct mutex mutex;
+	};
+
+#ifdef DEBUG
+	/** @brief _mali_osk_locks_debug_init/add/remove() functions are declared when DEBUG is enabled and
+	 * defined in file mali_osk_locks.c. When LOCK_ORDER_CHECKING is enabled, calling these functions when we
+	 * init/lock/unlock a lock/mutex, we could track lock order of a given tid. */
+	void _mali_osk_locks_debug_init(struct _mali_osk_lock_debug_s *checker, _mali_osk_lock_flags_t flags, _mali_osk_lock_order_t order);
+	void _mali_osk_locks_debug_add(struct _mali_osk_lock_debug_s *checker);
+	void _mali_osk_locks_debug_remove(struct _mali_osk_lock_debug_s *checker);
+
+	/** @brief This function can return a given lock's owner when DEBUG     is enabled. */
+	static inline u32 _mali_osk_lock_get_owner(struct _mali_osk_lock_debug_s *lock)
+	{
+		return lock->owner;
+	}
+#else
+#define _mali_osk_locks_debug_init(x, y, z) do {} while (0)
+#define _mali_osk_locks_debug_add(x) do {} while (0)
+#define _mali_osk_locks_debug_remove(x) do {} while (0)
+#endif
+
+	/** @brief Before use _mali_osk_spin_lock, init function should be used to allocate memory and initial spinlock*/
+	static inline _mali_osk_spinlock_t *_mali_osk_spinlock_init(_mali_osk_lock_flags_t flags, _mali_osk_lock_order_t order)
+	{
+		_mali_osk_spinlock_t *lock = NULL;
+
+		lock = kmalloc(sizeof(_mali_osk_spinlock_t), GFP_KERNEL);
+		if (NULL == lock) {
+			return NULL;
+		}
+		spin_lock_init(&lock->spinlock);
+		_mali_osk_locks_debug_init((struct _mali_osk_lock_debug_s *)lock, flags, order);
+		return lock;
+	}
+
+	/** @brief Lock a spinlock */
+	static inline void  _mali_osk_spinlock_lock(_mali_osk_spinlock_t *lock)
+	{
+		BUG_ON(NULL == lock);
+		spin_lock(&lock->spinlock);
+		_mali_osk_locks_debug_add((struct _mali_osk_lock_debug_s *)lock);
+	}
+
+	/** @brief Unlock a spinlock */
+	static inline void _mali_osk_spinlock_unlock(_mali_osk_spinlock_t *lock)
+	{
+		BUG_ON(NULL == lock);
+		_mali_osk_locks_debug_remove((struct _mali_osk_lock_debug_s *)lock);
+		spin_unlock(&lock->spinlock);
+	}
+
+	/** @brief Free a memory block which the argument lock pointed to and its type must be
+	 * _mali_osk_spinlock_t *. */
+	static inline void _mali_osk_spinlock_term(_mali_osk_spinlock_t *lock)
+	{
+		/* Parameter validation  */
+		BUG_ON(NULL == lock);
+
+		/* Linux requires no explicit termination of spinlocks, semaphores, or rw_semaphores */
+		kfree(lock);
+	}
+
+	/** @brief Before _mali_osk_spinlock_irq_lock/unlock/term() is called, init function should be
+	 * called to initial spinlock and flags in struct _mali_osk_spinlock_irq_t. */
+	static inline _mali_osk_spinlock_irq_t *_mali_osk_spinlock_irq_init(_mali_osk_lock_flags_t flags, _mali_osk_lock_order_t order)
+	{
+		_mali_osk_spinlock_irq_t *lock = NULL;
+		lock = kmalloc(sizeof(_mali_osk_spinlock_irq_t), GFP_KERNEL);
+
+		if (NULL == lock) {
+			return NULL;
+		}
+
+		lock->flags = 0;
+		spin_lock_init(&lock->spinlock);
+		_mali_osk_locks_debug_init((struct _mali_osk_lock_debug_s *)lock, flags, order);
+		return lock;
+	}
+
+	/** @brief Lock spinlock and save the register's state */
+	static inline void _mali_osk_spinlock_irq_lock(_mali_osk_spinlock_irq_t *lock)
+	{
+		unsigned long tmp_flags;
+
+		BUG_ON(NULL == lock);
+		spin_lock_irqsave(&lock->spinlock, tmp_flags);
+		lock->flags = tmp_flags;
+		_mali_osk_locks_debug_add((struct _mali_osk_lock_debug_s *)lock);
+	}
+
+	/** @brief Unlock spinlock with saved register's state */
+	static inline void _mali_osk_spinlock_irq_unlock(_mali_osk_spinlock_irq_t *lock)
+	{
+		BUG_ON(NULL == lock);
+		_mali_osk_locks_debug_remove((struct _mali_osk_lock_debug_s *)lock);
+		spin_unlock_irqrestore(&lock->spinlock, lock->flags);
+	}
+
+	/** @brief Destroy a given memory block which lock pointed to, and the lock type must be
+	 * _mali_osk_spinlock_irq_t *. */
+	static inline void _mali_osk_spinlock_irq_term(_mali_osk_spinlock_irq_t *lock)
+	{
+		/* Parameter validation  */
+		BUG_ON(NULL == lock);
+
+		/* Linux requires no explicit termination of spinlocks, semaphores, or rw_semaphores */
+		kfree(lock);
+	}
+
+	/** @brief Before _mali_osk_mutex_rw_wait/signal/term() is called, we should call
+	 * _mali_osk_mutex_rw_init() to kmalloc a memory block and initial part of elements in it. */
+	static inline _mali_osk_mutex_rw_t *_mali_osk_mutex_rw_init(_mali_osk_lock_flags_t flags, _mali_osk_lock_order_t order)
+	{
+		_mali_osk_mutex_rw_t *lock = NULL;
+
+		lock = kmalloc(sizeof(_mali_osk_mutex_rw_t), GFP_KERNEL);
+
+		if (NULL == lock) {
+			return NULL;
+		}
+
+		init_rwsem(&lock->rw_sema);
+		_mali_osk_locks_debug_init((struct _mali_osk_lock_debug_s *)lock, flags, order);
+		return lock;
+	}
+
+	/** @brief When call _mali_osk_mutex_rw_wait/signal() functions, the second argument mode
+	 * should be assigned with value _MALI_OSK_LOCKMODE_RO or _MALI_OSK_LOCKMODE_RW */
+	static inline void _mali_osk_mutex_rw_wait(_mali_osk_mutex_rw_t *lock, _mali_osk_lock_mode_t mode)
+	{
+		BUG_ON(NULL == lock);
+		BUG_ON(!(_MALI_OSK_LOCKMODE_RO == mode || _MALI_OSK_LOCKMODE_RW == mode));
+
+		if (mode == _MALI_OSK_LOCKMODE_RO) {
+			down_read(&lock->rw_sema);
+		} else {
+			down_write(&lock->rw_sema);
+		}
+
+#ifdef DEBUG
+		if (mode == _MALI_OSK_LOCKMODE_RW) {
+			lock->mode = mode;
+		} else { /* mode == _MALI_OSK_LOCKMODE_RO */
+			lock->mode = mode;
+		}
+		_mali_osk_locks_debug_add((struct _mali_osk_lock_debug_s *)lock);
+#endif
+	}
+
+	/** @brief Up lock->rw_sema with up_read/write() accordinf argument mode's value. */
+	static inline void  _mali_osk_mutex_rw_signal(_mali_osk_mutex_rw_t *lock, _mali_osk_lock_mode_t mode)
+	{
+		BUG_ON(NULL == lock);
+		BUG_ON(!(_MALI_OSK_LOCKMODE_RO == mode || _MALI_OSK_LOCKMODE_RW == mode));
+#ifdef DEBUG
+		/* make sure the thread releasing the lock actually was the owner */
+		if (mode == _MALI_OSK_LOCKMODE_RW) {
+			_mali_osk_locks_debug_remove((struct _mali_osk_lock_debug_s *)lock);
+			/* This lock now has no owner */
+			lock->checker.owner = 0;
+		}
+#endif
+
+		if (mode == _MALI_OSK_LOCKMODE_RO) {
+			up_read(&lock->rw_sema);
+		} else {
+			up_write(&lock->rw_sema);
+		}
+	}
+
+	/** @brief Free a given memory block which lock pointed to and its type must be
+	 * _mali_sok_mutex_rw_t *. */
+	static inline void _mali_osk_mutex_rw_term(_mali_osk_mutex_rw_t *lock)
+	{
+		/* Parameter validation  */
+		BUG_ON(NULL == lock);
+
+		/* Linux requires no explicit termination of spinlocks, semaphores, or rw_semaphores */
+		kfree(lock);
+	}
+
+	/** @brief Mutex & mutex_interruptible share the same init and term function, because they have the
+	 * same osk mutex struct, and the difference between them is which locking function they use */
+	static inline _mali_osk_mutex_t *_mali_osk_mutex_init(_mali_osk_lock_flags_t flags, _mali_osk_lock_order_t order)
+	{
+		_mali_osk_mutex_t *lock = NULL;
+
+		lock = kmalloc(sizeof(_mali_osk_mutex_t), GFP_KERNEL);
+
+		if (NULL == lock) {
+			return NULL;
+		}
+		mutex_init(&lock->mutex);
+
+		_mali_osk_locks_debug_init((struct _mali_osk_lock_debug_s *)lock, flags, order);
+		return lock;
+	}
+
+	/** @brief  Lock the lock->mutex with mutex_lock_interruptible function */
+	static inline _mali_osk_errcode_t _mali_osk_mutex_wait_interruptible(_mali_osk_mutex_t *lock)
+	{
+		_mali_osk_errcode_t err = _MALI_OSK_ERR_OK;
+
+		BUG_ON(NULL == lock);
+
+		if (mutex_lock_interruptible(&lock->mutex)) {
+			printk(KERN_WARNING "Mali: Can not lock mutex\n");
+			err = _MALI_OSK_ERR_RESTARTSYSCALL;
+		}
+
+		_mali_osk_locks_debug_add((struct _mali_osk_lock_debug_s *)lock);
+		return err;
+	}
+
+	/** @brief Unlock the lock->mutex which is locked with mutex_lock_interruptible() function. */
+	static inline void _mali_osk_mutex_signal_interruptible(_mali_osk_mutex_t *lock)
+	{
+		BUG_ON(NULL == lock);
+		_mali_osk_locks_debug_remove((struct _mali_osk_lock_debug_s *)lock);
+		mutex_unlock(&lock->mutex);
+	}
+
+	/** @brief Lock the lock->mutex just with mutex_lock() function which could not be interruptted. */
+	static inline void _mali_osk_mutex_wait(_mali_osk_mutex_t *lock)
+	{
+		BUG_ON(NULL == lock);
+		mutex_lock(&lock->mutex);
+		_mali_osk_locks_debug_add((struct _mali_osk_lock_debug_s *)lock);
+	}
+
+	/** @brief Unlock the lock->mutex which is locked with mutex_lock() function. */
+	static inline void _mali_osk_mutex_signal(_mali_osk_mutex_t *lock)
+	{
+		BUG_ON(NULL == lock);
+		_mali_osk_locks_debug_remove((struct _mali_osk_lock_debug_s *)lock);
+		mutex_unlock(&lock->mutex);
+	}
+
+	/** @brief Free a given memory block which lock point. */
+	static inline void _mali_osk_mutex_term(_mali_osk_mutex_t *lock)
+	{
+		/* Parameter validation  */
+		BUG_ON(NULL == lock);
+
+		/* Linux requires no explicit termination of spinlocks, semaphores, or rw_semaphores */
+		kfree(lock);
+	}
+
+#ifdef _cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_low_level_mem.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_low_level_mem.c
@@ -0,0 +1,150 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_low_level_mem.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include <asm/io.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_ukk.h"
+
+void _mali_osk_mem_barrier(void)
+{
+	mb();
+}
+
+void _mali_osk_write_mem_barrier(void)
+{
+	wmb();
+}
+
+mali_io_address _mali_osk_mem_mapioregion(uintptr_t phys, u32 size, const char *description)
+{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+	return (mali_io_address)ioremap(phys, size);
+#else
+	return (mali_io_address)ioremap_nocache(phys, size);
+#endif
+}
+
+void _mali_osk_mem_unmapioregion(uintptr_t phys, u32 size, mali_io_address virt)
+{
+	iounmap((void *)virt);
+}
+
+_mali_osk_errcode_t inline _mali_osk_mem_reqregion(uintptr_t phys, u32 size, const char *description)
+{
+#if MALI_LICENSE_IS_GPL
+	return _MALI_OSK_ERR_OK; /* GPL driver gets the mem region for the resources registered automatically */
+#else
+	return ((NULL == request_mem_region(phys, size, description)) ? _MALI_OSK_ERR_NOMEM : _MALI_OSK_ERR_OK);
+#endif
+}
+
+void inline _mali_osk_mem_unreqregion(uintptr_t phys, u32 size)
+{
+#if !MALI_LICENSE_IS_GPL
+	release_mem_region(phys, size);
+#endif
+}
+
+void inline _mali_osk_mem_iowrite32_relaxed(volatile mali_io_address addr, u32 offset, u32 val)
+{
+	__raw_writel(cpu_to_le32(val), ((u8 *)addr) + offset);
+}
+
+u32 inline _mali_osk_mem_ioread32(volatile mali_io_address addr, u32 offset)
+{
+	return ioread32(((u8 *)addr) + offset);
+}
+
+void inline _mali_osk_mem_iowrite32(volatile mali_io_address addr, u32 offset, u32 val)
+{
+	iowrite32(val, ((u8 *)addr) + offset);
+}
+
+void _mali_osk_cache_flushall(void)
+{
+	/** @note Cached memory is not currently supported in this implementation */
+}
+
+void _mali_osk_cache_ensure_uncached_range_flushed(void *uncached_mapping, u32 offset, u32 size)
+{
+	_mali_osk_write_mem_barrier();
+}
+
+u32 _mali_osk_mem_write_safe(void __user *dest, const void __user *src, u32 size)
+{
+#define MALI_MEM_SAFE_COPY_BLOCK_SIZE 4096
+	u32 retval = 0;
+	void *temp_buf;
+
+	temp_buf = kmalloc(MALI_MEM_SAFE_COPY_BLOCK_SIZE, GFP_KERNEL);
+	if (NULL != temp_buf) {
+		u32 bytes_left_to_copy = size;
+		u32 i;
+		for (i = 0; i < size; i += MALI_MEM_SAFE_COPY_BLOCK_SIZE) {
+			u32 size_to_copy;
+			u32 size_copied;
+			u32 bytes_left;
+
+			if (bytes_left_to_copy > MALI_MEM_SAFE_COPY_BLOCK_SIZE) {
+				size_to_copy = MALI_MEM_SAFE_COPY_BLOCK_SIZE;
+			} else {
+				size_to_copy = bytes_left_to_copy;
+			}
+
+			bytes_left = copy_from_user(temp_buf, ((char *)src) + i, size_to_copy);
+			size_copied = size_to_copy - bytes_left;
+
+			bytes_left = copy_to_user(((char *)dest) + i, temp_buf, size_copied);
+			size_copied -= bytes_left;
+
+			bytes_left_to_copy -= size_copied;
+			retval += size_copied;
+
+			if (size_copied != size_to_copy) {
+				break; /* Early out, we was not able to copy this entire block */
+			}
+		}
+
+		kfree(temp_buf);
+	}
+
+	return retval;
+}
+
+_mali_osk_errcode_t _mali_ukk_mem_write_safe(_mali_uk_mem_write_safe_s *args)
+{
+	void __user *src;
+	void __user *dst;
+	struct mali_session_data *session;
+
+	MALI_DEBUG_ASSERT_POINTER(args);
+
+	session = (struct mali_session_data *)(uintptr_t)args->ctx;
+
+	if (NULL == session) {
+		return _MALI_OSK_ERR_INVALID_ARGS;
+	}
+
+	src = (void __user *)(uintptr_t)args->src;
+	dst = (void __user *)(uintptr_t)args->dest;
+
+	/* Return number of bytes actually copied */
+	args->size = _mali_osk_mem_write_safe(dst, src, args->size);
+	return _MALI_OSK_ERR_OK;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_mali.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_mali.c
@@ -0,0 +1,496 @@
+/*
+ * Copyright (C) 2010-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_mali.c
+ * Implementation of the OS abstraction layer which is specific for the Mali kernel device driver
+ */
+#include <linux/kernel.h>
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+#include <linux/platform_device.h>
+#include <linux/mali/mali_utgard.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+#include "mali_osk_mali.h"
+#include "mali_kernel_common.h" /* MALI_xxx macros */
+#include "mali_osk.h"           /* kernel side OS functions */
+#include "mali_kernel_linux.h"
+
+static mali_bool mali_secure_mode_enabled = MALI_FALSE;
+static mali_bool mali_secure_mode_supported = MALI_FALSE;
+
+/* Function that init the mali gpu secure mode */
+void (*mali_secure_mode_deinit)(void) = NULL;
+/* Function that reset GPU and enable the mali gpu secure mode */
+int (*mali_gpu_reset_and_secure_mode_enable)(void) = NULL;
+/* Function that reset GPU and disable the mali gpu secure mode */
+int (*mali_gpu_reset_and_secure_mode_disable)(void) = NULL;
+
+#ifdef CONFIG_MALI_DT
+
+#define MALI_OSK_INVALID_RESOURCE_ADDRESS 0xFFFFFFFF
+
+/**
+ * Define the max number of resource we could have.
+ */
+#define MALI_OSK_MAX_RESOURCE_NUMBER 27
+
+/**
+ * Define the max number of resource with interrupts, and they are
+ * the first 20 elements in array mali_osk_resource_bank.
+ */
+#define MALI_OSK_RESOURCE_WITH_IRQ_NUMBER 20
+
+/**
+ * pp core start and end location in mali_osk_resource_bank array.
+ */
+#define MALI_OSK_RESOURCE_PP_LOCATION_START 2
+#define MALI_OSK_RESOURCE_PP_LOCATION_END 17
+
+/**
+ * L2 cache start and end location in mali_osk_resource_bank array.
+ */
+#define MALI_OSK_RESOURCE_L2_LOCATION_START 20
+#define MALI_OSK_RESOURCE_l2_LOCATION_END 22
+
+/**
+ * DMA unit location.
+ */
+#define MALI_OSK_RESOURCE_DMA_LOCATION 26
+
+static _mali_osk_resource_t mali_osk_resource_bank[MALI_OSK_MAX_RESOURCE_NUMBER] = {
+	{.description = "Mali_GP", .base = MALI_OFFSET_GP, .irq_name = "IRQGP",},
+	{.description = "Mali_GP_MMU", .base = MALI_OFFSET_GP_MMU, .irq_name = "IRQGPMMU",},
+	{.description = "Mali_PP0", .base = MALI_OFFSET_PP0, .irq_name = "IRQPP0",},
+	{.description = "Mali_PP0_MMU", .base = MALI_OFFSET_PP0_MMU, .irq_name = "IRQPPMMU0",},
+	{.description = "Mali_PP1", .base = MALI_OFFSET_PP1, .irq_name = "IRQPP1",},
+	{.description = "Mali_PP1_MMU", .base = MALI_OFFSET_PP1_MMU, .irq_name = "IRQPPMMU1",},
+	{.description = "Mali_PP2", .base = MALI_OFFSET_PP2, .irq_name = "IRQPP2",},
+	{.description = "Mali_PP2_MMU", .base = MALI_OFFSET_PP2_MMU, .irq_name = "IRQPPMMU2",},
+	{.description = "Mali_PP3", .base = MALI_OFFSET_PP3, .irq_name = "IRQPP3",},
+	{.description = "Mali_PP3_MMU", .base = MALI_OFFSET_PP3_MMU, .irq_name = "IRQPPMMU3",},
+	{.description = "Mali_PP4", .base = MALI_OFFSET_PP4, .irq_name = "IRQPP4",},
+	{.description = "Mali_PP4_MMU", .base = MALI_OFFSET_PP4_MMU, .irq_name = "IRQPPMMU4",},
+	{.description = "Mali_PP5", .base = MALI_OFFSET_PP5, .irq_name = "IRQPP5",},
+	{.description = "Mali_PP5_MMU", .base = MALI_OFFSET_PP5_MMU, .irq_name = "IRQPPMMU5",},
+	{.description = "Mali_PP6", .base = MALI_OFFSET_PP6, .irq_name = "IRQPP6",},
+	{.description = "Mali_PP6_MMU", .base = MALI_OFFSET_PP6_MMU, .irq_name = "IRQPPMMU6",},
+	{.description = "Mali_PP7", .base = MALI_OFFSET_PP7, .irq_name = "IRQPP7",},
+	{.description = "Mali_PP7_MMU", .base = MALI_OFFSET_PP7_MMU, .irq_name = "IRQPPMMU",},
+	{.description = "Mali_PP_Broadcast", .base = MALI_OFFSET_PP_BCAST, .irq_name = "IRQPP",},
+	{.description = "Mali_PMU", .base = MALI_OFFSET_PMU, .irq_name = "IRQPMU",},
+	{.description = "Mali_L2", .base = MALI_OFFSET_L2_RESOURCE0,},
+	{.description = "Mali_L2", .base = MALI_OFFSET_L2_RESOURCE1,},
+	{.description = "Mali_L2", .base = MALI_OFFSET_L2_RESOURCE2,},
+	{.description = "Mali_PP_MMU_Broadcast", .base = MALI_OFFSET_PP_BCAST_MMU,},
+	{.description = "Mali_Broadcast", .base = MALI_OFFSET_BCAST,},
+	{.description = "Mali_DLBU", .base = MALI_OFFSET_DLBU,},
+	{.description = "Mali_DMA", .base = MALI_OFFSET_DMA,},
+};
+
+static int _mali_osk_get_compatible_name(const char **out_string)
+{
+	struct device_node *node = mali_platform_device->dev.of_node;
+
+	MALI_DEBUG_ASSERT(NULL != node);
+
+	return of_property_read_string(node, "compatible", out_string);
+}
+
+_mali_osk_errcode_t _mali_osk_resource_initialize(void)
+{
+	mali_bool mali_is_450 = MALI_FALSE, mali_is_470 = MALI_FALSE;
+	int i, pp_core_num = 0, l2_core_num = 0;
+	struct resource *res;
+	const char *compatible_name = NULL;
+
+	if (0 == _mali_osk_get_compatible_name(&compatible_name)) {
+		if (0 == strncmp(compatible_name, "arm,mali-450", strlen("arm,mali-450"))) {
+			mali_is_450 = MALI_TRUE;
+			MALI_DEBUG_PRINT(2, ("mali-450 device tree detected."));
+		} else if (0 == strncmp(compatible_name, "arm,mali-470", strlen("arm,mali-470"))) {
+			mali_is_470 = MALI_TRUE;
+			MALI_DEBUG_PRINT(2, ("mali-470 device tree detected."));
+		}
+	}
+
+	for (i = 0; i < MALI_OSK_RESOURCE_WITH_IRQ_NUMBER; i++) {
+		res = platform_get_resource_byname(mali_platform_device, IORESOURCE_IRQ, mali_osk_resource_bank[i].irq_name);
+		if (res) {
+			mali_osk_resource_bank[i].irq = res->start;
+		} else {
+			mali_osk_resource_bank[i].base = MALI_OSK_INVALID_RESOURCE_ADDRESS;
+		}
+	}
+
+	for (i = MALI_OSK_RESOURCE_PP_LOCATION_START; i <= MALI_OSK_RESOURCE_PP_LOCATION_END; i++) {
+		if (MALI_OSK_INVALID_RESOURCE_ADDRESS != mali_osk_resource_bank[i].base) {
+			pp_core_num++;
+		}
+	}
+
+	/* We have to divide by 2, because we caculate twice for only one pp(pp_core and pp_mmu_core). */
+	if (0 != pp_core_num % 2) {
+		MALI_DEBUG_PRINT(2, ("The value of pp core number isn't normal."));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	pp_core_num /= 2;
+
+	/**
+	 * we can caculate the number of l2 cache core according the number of pp core number
+	 * and device type(mali400/mali450/mali470).
+	 */
+	l2_core_num = 1;
+	if (mali_is_450) {
+		if (pp_core_num > 4) {
+			l2_core_num = 3;
+		} else if (pp_core_num <= 4) {
+			l2_core_num = 2;
+		}
+	}
+
+	for (i = MALI_OSK_RESOURCE_l2_LOCATION_END; i > MALI_OSK_RESOURCE_L2_LOCATION_START + l2_core_num - 1; i--) {
+		mali_osk_resource_bank[i].base = MALI_OSK_INVALID_RESOURCE_ADDRESS;
+	}
+
+	/* If device is not mali-450 type, we have to remove related resource from resource bank. */
+	if (!(mali_is_450 || mali_is_470)) {
+		for (i = MALI_OSK_RESOURCE_l2_LOCATION_END + 1; i < MALI_OSK_MAX_RESOURCE_NUMBER; i++) {
+			mali_osk_resource_bank[i].base = MALI_OSK_INVALID_RESOURCE_ADDRESS;
+		}
+	}
+
+	if (mali_is_470)
+		mali_osk_resource_bank[MALI_OSK_RESOURCE_DMA_LOCATION].base = MALI_OSK_INVALID_RESOURCE_ADDRESS;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_osk_resource_find(u32 addr, _mali_osk_resource_t *res)
+{
+	int i;
+
+	if (NULL == mali_platform_device) {
+		return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	}
+
+	/* Traverse all of resources in resources bank to find the matching one. */
+	for (i = 0; i < MALI_OSK_MAX_RESOURCE_NUMBER; i++) {
+		if (mali_osk_resource_bank[i].base == addr) {
+			if (NULL != res) {
+				res->base = addr + _mali_osk_resource_base_address();
+				res->description = mali_osk_resource_bank[i].description;
+				res->irq = mali_osk_resource_bank[i].irq;
+			}
+			return _MALI_OSK_ERR_OK;
+		}
+	}
+
+	return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+}
+
+uintptr_t _mali_osk_resource_base_address(void)
+{
+	struct resource *reg_res = NULL;
+	uintptr_t ret = 0;
+
+	reg_res = platform_get_resource(mali_platform_device, IORESOURCE_MEM, 0);
+
+	if (NULL != reg_res) {
+		ret = reg_res->start;
+	}
+
+	return ret;
+}
+
+void _mali_osk_device_data_pmu_config_get(u16 *domain_config_array, int array_size)
+{
+	struct device_node *node = mali_platform_device->dev.of_node;
+	struct property *prop;
+	const __be32 *p;
+	int length = 0, i = 0;
+	u32 u;
+
+	MALI_DEBUG_PRINT(2, ("Get pmu config from device tree configuration.\n"));
+
+	MALI_DEBUG_ASSERT(NULL != node);
+
+	if (!of_get_property(node, "pmu_domain_config", &length)) {
+		return;
+	}
+
+	if (array_size != length / sizeof(u32)) {
+		MALI_PRINT_ERROR(("Wrong pmu domain config in device tree."));
+		return;
+	}
+
+	of_property_for_each_u32(node, "pmu_domain_config", prop, p, u) {
+		domain_config_array[i] = (u16)u;
+		i++;
+	}
+
+	return;
+}
+
+u32 _mali_osk_get_pmu_switch_delay(void)
+{
+	struct device_node *node = mali_platform_device->dev.of_node;
+	u32 switch_delay;
+
+	MALI_DEBUG_ASSERT(NULL != node);
+
+	if (0 == of_property_read_u32(node, "pmu_switch_delay", &switch_delay)) {
+		return switch_delay;
+	} else {
+		MALI_DEBUG_PRINT(2, ("Couldn't find pmu_switch_delay in device tree configuration.\n"));
+	}
+
+	return 0;
+}
+
+#else /* CONFIG_MALI_DT */
+
+_mali_osk_errcode_t _mali_osk_resource_find(u32 addr, _mali_osk_resource_t *res)
+{
+	int i;
+	uintptr_t phys_addr;
+
+	if (NULL == mali_platform_device) {
+		/* Not connected to a device */
+		return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	}
+
+	phys_addr = addr + _mali_osk_resource_base_address();
+	for (i = 0; i < mali_platform_device->num_resources; i++) {
+		if (IORESOURCE_MEM == resource_type(&(mali_platform_device->resource[i])) &&
+		    mali_platform_device->resource[i].start == phys_addr) {
+			if (NULL != res) {
+				res->base = phys_addr;
+				res->description = mali_platform_device->resource[i].name;
+
+				/* Any (optional) IRQ resource belonging to this resource will follow */
+				if ((i + 1) < mali_platform_device->num_resources &&
+				    IORESOURCE_IRQ == resource_type(&(mali_platform_device->resource[i + 1]))) {
+					res->irq = mali_platform_device->resource[i + 1].start;
+				} else {
+					res->irq = -1;
+				}
+			}
+			return _MALI_OSK_ERR_OK;
+		}
+	}
+
+	return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+}
+
+uintptr_t _mali_osk_resource_base_address(void)
+{
+	uintptr_t lowest_addr = (uintptr_t)(0 - 1);
+	uintptr_t ret = 0;
+
+	if (NULL != mali_platform_device) {
+		int i;
+		for (i = 0; i < mali_platform_device->num_resources; i++) {
+			if (mali_platform_device->resource[i].flags & IORESOURCE_MEM &&
+			    mali_platform_device->resource[i].start < lowest_addr) {
+				lowest_addr = mali_platform_device->resource[i].start;
+				ret = lowest_addr;
+			}
+		}
+	}
+
+	return ret;
+}
+
+void _mali_osk_device_data_pmu_config_get(u16 *domain_config_array, int array_size)
+{
+	_mali_osk_device_data data = { 0, };
+
+	MALI_DEBUG_PRINT(2, ("Get pmu config from platform device data.\n"));
+	if (_MALI_OSK_ERR_OK == _mali_osk_device_data_get(&data)) {
+		/* Copy the custom customer power domain config */
+		_mali_osk_memcpy(domain_config_array, data.pmu_domain_config, sizeof(data.pmu_domain_config));
+	}
+
+	return;
+}
+
+u32 _mali_osk_get_pmu_switch_delay(void)
+{
+	_mali_osk_errcode_t err;
+	_mali_osk_device_data data = { 0, };
+
+	err = _mali_osk_device_data_get(&data);
+
+	if (_MALI_OSK_ERR_OK == err) {
+		return data.pmu_switch_delay;
+	}
+
+	return 0;
+}
+#endif /* CONFIG_MALI_DT */
+
+_mali_osk_errcode_t _mali_osk_device_data_get(_mali_osk_device_data *data)
+{
+	MALI_DEBUG_ASSERT_POINTER(data);
+
+	if (NULL != mali_platform_device) {
+		struct mali_gpu_device_data *os_data = NULL;
+
+		os_data = (struct mali_gpu_device_data *)mali_platform_device->dev.platform_data;
+		if (NULL != os_data) {
+			/* Copy data from OS dependant struct to Mali neutral struct (identical!) */
+			BUILD_BUG_ON(sizeof(*os_data) != sizeof(*data));
+			_mali_osk_memcpy(data, os_data, sizeof(*os_data));
+
+			return _MALI_OSK_ERR_OK;
+		}
+	}
+
+	return _MALI_OSK_ERR_ITEM_NOT_FOUND;
+}
+
+u32 _mali_osk_identify_gpu_resource(void)
+{
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI_OFFSET_L2_RESOURCE1, NULL))
+		/* Mali 450 */
+		return 0x450;
+
+	if (_MALI_OSK_ERR_OK == _mali_osk_resource_find(MALI_OFFSET_DLBU, NULL))
+		/* Mali 470 */
+		return 0x470;
+
+	/* Mali 400 */
+	return 0x400;
+}
+
+mali_bool _mali_osk_shared_interrupts(void)
+{
+	u32 irqs[128];
+	u32 i, j, irq, num_irqs_found = 0;
+
+	MALI_DEBUG_ASSERT_POINTER(mali_platform_device);
+	MALI_DEBUG_ASSERT(128 >= mali_platform_device->num_resources);
+
+	for (i = 0; i < mali_platform_device->num_resources; i++) {
+		if (IORESOURCE_IRQ & mali_platform_device->resource[i].flags) {
+			irq = mali_platform_device->resource[i].start;
+
+			for (j = 0; j < num_irqs_found; ++j) {
+				if (irq == irqs[j]) {
+					return MALI_TRUE;
+				}
+			}
+
+			irqs[num_irqs_found++] = irq;
+		}
+	}
+
+	return MALI_FALSE;
+}
+
+_mali_osk_errcode_t _mali_osk_gpu_secure_mode_init(void)
+{
+	_mali_osk_device_data data = { 0, };
+
+	if (_MALI_OSK_ERR_OK ==  _mali_osk_device_data_get(&data)) {
+		if ((NULL != data.secure_mode_init) && (NULL != data.secure_mode_deinit)
+		    && (NULL != data.gpu_reset_and_secure_mode_enable) && (NULL != data.gpu_reset_and_secure_mode_disable)) {
+			int err = data.secure_mode_init();
+			if (err) {
+				MALI_DEBUG_PRINT(1, ("Failed to init gpu secure mode.\n"));
+				return _MALI_OSK_ERR_FAULT;
+			}
+
+			mali_secure_mode_deinit = data.secure_mode_deinit;
+			mali_gpu_reset_and_secure_mode_enable = data.gpu_reset_and_secure_mode_enable;
+			mali_gpu_reset_and_secure_mode_disable = data.gpu_reset_and_secure_mode_disable;
+
+			mali_secure_mode_supported = MALI_TRUE;
+			mali_secure_mode_enabled = MALI_FALSE;
+			return _MALI_OSK_ERR_OK;
+		}
+	}
+	MALI_DEBUG_PRINT(3, ("GPU secure mode not supported.\n"));
+	return _MALI_OSK_ERR_UNSUPPORTED;
+
+}
+
+_mali_osk_errcode_t _mali_osk_gpu_secure_mode_deinit(void)
+{
+	if (NULL !=  mali_secure_mode_deinit) {
+		mali_secure_mode_deinit();
+		mali_secure_mode_enabled = MALI_FALSE;
+		mali_secure_mode_supported = MALI_FALSE;
+		return _MALI_OSK_ERR_OK;
+	}
+	MALI_DEBUG_PRINT(3, ("GPU secure mode not supported.\n"));
+	return _MALI_OSK_ERR_UNSUPPORTED;
+
+}
+
+
+_mali_osk_errcode_t _mali_osk_gpu_reset_and_secure_mode_enable(void)
+{
+	/* the mali executor lock must be held before enter this function. */
+
+	MALI_DEBUG_ASSERT(MALI_FALSE == mali_secure_mode_enabled);
+
+	if (NULL !=  mali_gpu_reset_and_secure_mode_enable) {
+		if (mali_gpu_reset_and_secure_mode_enable()) {
+			MALI_DEBUG_PRINT(1, ("Failed to reset GPU or enable gpu secure mode.\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+		mali_secure_mode_enabled = MALI_TRUE;
+		return _MALI_OSK_ERR_OK;
+	}
+	MALI_DEBUG_PRINT(1, ("GPU secure mode not supported.\n"));
+	return _MALI_OSK_ERR_UNSUPPORTED;
+}
+
+_mali_osk_errcode_t _mali_osk_gpu_reset_and_secure_mode_disable(void)
+{
+	/* the mali executor lock must be held before enter this function. */
+
+	MALI_DEBUG_ASSERT(MALI_TRUE == mali_secure_mode_enabled);
+
+	if (NULL != mali_gpu_reset_and_secure_mode_disable) {
+		if (mali_gpu_reset_and_secure_mode_disable()) {
+			MALI_DEBUG_PRINT(1, ("Failed to reset GPU or disable gpu secure mode.\n"));
+			return _MALI_OSK_ERR_FAULT;
+		}
+		mali_secure_mode_enabled = MALI_FALSE;
+
+		return _MALI_OSK_ERR_OK;
+
+	}
+	MALI_DEBUG_PRINT(1, ("GPU secure mode not supported.\n"));
+	return _MALI_OSK_ERR_UNSUPPORTED;
+
+}
+
+mali_bool _mali_osk_gpu_secure_mode_is_enabled(void)
+{
+	return mali_secure_mode_enabled;
+}
+
+mali_bool _mali_osk_gpu_secure_mode_is_supported(void)
+{
+	return mali_secure_mode_supported;
+}
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_math.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_math.c
@@ -0,0 +1,27 @@
+/*
+ * Copyright (C) 2010, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_math.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include "mali_osk.h"
+#include <linux/bitops.h>
+
+u32 _mali_osk_clz(u32 input)
+{
+	return 32 - fls(input);
+}
+
+u32 _mali_osk_fls(u32 input)
+{
+	return fls(input);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_memory.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_memory.c
@@ -0,0 +1,61 @@
+/*
+ * Copyright (C) 2010-2011, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_memory.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include "mali_osk.h"
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+
+void inline *_mali_osk_calloc(u32 n, u32 size)
+{
+	return kcalloc(n, size, GFP_KERNEL);
+}
+
+void inline *_mali_osk_malloc(u32 size)
+{
+	return kmalloc(size, GFP_KERNEL);
+}
+
+void inline _mali_osk_free(void *ptr)
+{
+	kfree(ptr);
+}
+
+void inline *_mali_osk_valloc(u32 size)
+{
+	return vmalloc(size);
+}
+
+void inline _mali_osk_vfree(void *ptr)
+{
+	vfree(ptr);
+}
+
+void inline *_mali_osk_memcpy(void *dst, const void *src, u32  len)
+{
+	return memcpy(dst, src, len);
+}
+
+void inline *_mali_osk_memset(void *s, u32 c, u32 n)
+{
+	return memset(s, c, n);
+}
+
+mali_bool _mali_osk_mem_check_allocated(u32 max_allocated)
+{
+	/* No need to prevent an out-of-memory dialogue appearing on Linux,
+	 * so we always return MALI_TRUE.
+	 */
+	return MALI_TRUE;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_misc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_misc.c
@@ -0,0 +1,86 @@
+/*
+ * Copyright (C) 2010-2014, 2016-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_misc.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+#include <linux/kernel.h>
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+#include <asm/cacheflush.h>
+#include <linux/sched.h>
+#include <linux/seq_file.h>
+#include <linux/module.h>
+#include "mali_osk.h"
+
+#if !defined(CONFIG_MALI_QUIET)
+void _mali_osk_dbgmsg(const char *fmt, ...)
+{
+	va_list args;
+	va_start(args, fmt);
+	vprintk(fmt, args);
+	va_end(args);
+}
+#endif /* !defined(CONFIG_MALI_QUIET) */
+
+u32 _mali_osk_snprintf(char *buf, u32 size, const char *fmt, ...)
+{
+	int res;
+	va_list args;
+	va_start(args, fmt);
+
+	res = vscnprintf(buf, (size_t)size, fmt, args);
+
+	va_end(args);
+	return res;
+}
+
+void _mali_osk_abort(void)
+{
+	/* make a simple fault by dereferencing a NULL pointer */
+	dump_stack();
+	*(int *)0 = 0;
+}
+
+void _mali_osk_break(void)
+{
+	_mali_osk_abort();
+}
+
+u32 _mali_osk_get_pid(void)
+{
+	/* Thread group ID is the process ID on Linux */
+	return (u32)current->tgid;
+}
+
+char *_mali_osk_get_comm(void)
+{
+	return (char *)current->comm;
+}
+
+
+u32 _mali_osk_get_tid(void)
+{
+	/* pid is actually identifying the thread on Linux */
+	u32 tid = current->pid;
+
+	/* If the pid is 0 the core was idle.  Instead of returning 0 we return a special number
+	 * identifying which core we are on. */
+	if (0 == tid) {
+		tid = -(1 + raw_smp_processor_id());
+	}
+
+	return tid;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_notification.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_notification.c
@@ -0,0 +1,187 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_notification.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+/**
+ * Declaration of the notification queue object type
+ * Contains a linked list of notification pending delivery to user space.
+ * It also contains a wait queue of exclusive waiters blocked in the ioctl
+ * When a new notification is posted a single thread is resumed.
+ */
+struct _mali_osk_notification_queue_t_struct {
+	spinlock_t mutex; /**< Mutex protecting the list */
+	wait_queue_head_t receive_queue; /**< Threads waiting for new entries to the queue */
+	struct list_head head; /**< List of notifications waiting to be picked up */
+};
+
+typedef struct _mali_osk_notification_wrapper_t_struct {
+	struct list_head list;           /**< Internal linked list variable */
+	_mali_osk_notification_t data;   /**< Notification data */
+} _mali_osk_notification_wrapper_t;
+
+_mali_osk_notification_queue_t *_mali_osk_notification_queue_init(void)
+{
+	_mali_osk_notification_queue_t         *result;
+
+	result = (_mali_osk_notification_queue_t *)kmalloc(sizeof(_mali_osk_notification_queue_t), GFP_KERNEL);
+	if (NULL == result) return NULL;
+
+	spin_lock_init(&result->mutex);
+	init_waitqueue_head(&result->receive_queue);
+	INIT_LIST_HEAD(&result->head);
+
+	return result;
+}
+
+_mali_osk_notification_t *_mali_osk_notification_create(u32 type, u32 size)
+{
+	/* OPT Recycling of notification objects */
+	_mali_osk_notification_wrapper_t *notification;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+	notification = (_mali_osk_notification_wrapper_t *)kmalloc(sizeof(_mali_osk_notification_wrapper_t) + size,
+			GFP_KERNEL | __GFP_HIGH | __GFP_RETRY_MAYFAIL);
+#else
+	notification = (_mali_osk_notification_wrapper_t *)kmalloc(sizeof(_mali_osk_notification_wrapper_t) + size,
+			GFP_KERNEL | __GFP_HIGH | __GFP_REPEAT);
+#endif
+	if (NULL == notification) {
+		MALI_DEBUG_PRINT(1, ("Failed to create a notification object\n"));
+		return NULL;
+	}
+
+	/* Init the list */
+	INIT_LIST_HEAD(&notification->list);
+
+	if (0 != size) {
+		notification->data.result_buffer = ((u8 *)notification) + sizeof(_mali_osk_notification_wrapper_t);
+	} else {
+		notification->data.result_buffer = NULL;
+	}
+
+	/* set up the non-allocating fields */
+	notification->data.notification_type = type;
+	notification->data.result_buffer_size = size;
+
+	/* all ok */
+	return &(notification->data);
+}
+
+void _mali_osk_notification_delete(_mali_osk_notification_t *object)
+{
+	_mali_osk_notification_wrapper_t *notification;
+	MALI_DEBUG_ASSERT_POINTER(object);
+
+	notification = container_of(object, _mali_osk_notification_wrapper_t, data);
+
+	/* Free the container */
+	kfree(notification);
+}
+
+void _mali_osk_notification_queue_term(_mali_osk_notification_queue_t *queue)
+{
+	_mali_osk_notification_t *result;
+	MALI_DEBUG_ASSERT_POINTER(queue);
+
+	while (_MALI_OSK_ERR_OK == _mali_osk_notification_queue_dequeue(queue, &result)) {
+		_mali_osk_notification_delete(result);
+	}
+
+	/* not much to do, just free the memory */
+	kfree(queue);
+}
+void _mali_osk_notification_queue_send(_mali_osk_notification_queue_t *queue, _mali_osk_notification_t *object)
+{
+#if defined(MALI_UPPER_HALF_SCHEDULING)
+	unsigned long irq_flags;
+#endif
+
+	_mali_osk_notification_wrapper_t *notification;
+	MALI_DEBUG_ASSERT_POINTER(queue);
+	MALI_DEBUG_ASSERT_POINTER(object);
+
+	notification = container_of(object, _mali_osk_notification_wrapper_t, data);
+
+#if defined(MALI_UPPER_HALF_SCHEDULING)
+	spin_lock_irqsave(&queue->mutex, irq_flags);
+#else
+	spin_lock(&queue->mutex);
+#endif
+
+	list_add_tail(&notification->list, &queue->head);
+
+#if defined(MALI_UPPER_HALF_SCHEDULING)
+	spin_unlock_irqrestore(&queue->mutex, irq_flags);
+#else
+	spin_unlock(&queue->mutex);
+#endif
+
+	/* and wake up one possible exclusive waiter */
+	wake_up(&queue->receive_queue);
+}
+
+_mali_osk_errcode_t _mali_osk_notification_queue_dequeue(_mali_osk_notification_queue_t *queue, _mali_osk_notification_t **result)
+{
+#if defined(MALI_UPPER_HALF_SCHEDULING)
+	unsigned long irq_flags;
+#endif
+
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_ITEM_NOT_FOUND;
+	_mali_osk_notification_wrapper_t *wrapper_object;
+
+#if defined(MALI_UPPER_HALF_SCHEDULING)
+	spin_lock_irqsave(&queue->mutex, irq_flags);
+#else
+	spin_lock(&queue->mutex);
+#endif
+
+	if (!list_empty(&queue->head)) {
+		wrapper_object = list_entry(queue->head.next, _mali_osk_notification_wrapper_t, list);
+		*result = &(wrapper_object->data);
+		list_del_init(&wrapper_object->list);
+		ret = _MALI_OSK_ERR_OK;
+	}
+
+#if defined(MALI_UPPER_HALF_SCHEDULING)
+	spin_unlock_irqrestore(&queue->mutex, irq_flags);
+#else
+	spin_unlock(&queue->mutex);
+#endif
+
+	return ret;
+}
+
+_mali_osk_errcode_t _mali_osk_notification_queue_receive(_mali_osk_notification_queue_t *queue, _mali_osk_notification_t **result)
+{
+	/* check input */
+	MALI_DEBUG_ASSERT_POINTER(queue);
+	MALI_DEBUG_ASSERT_POINTER(result);
+
+	/* default result */
+	*result = NULL;
+
+	if (wait_event_interruptible(queue->receive_queue,
+				     _MALI_OSK_ERR_OK == _mali_osk_notification_queue_dequeue(queue, result))) {
+		return _MALI_OSK_ERR_RESTARTSYSCALL;
+	}
+
+	return _MALI_OSK_ERR_OK; /* all ok */
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_pm.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_pm.c
@@ -0,0 +1,83 @@
+/**
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_pm.c
+ * Implementation of the callback functions from common power management
+ */
+
+#include <linux/sched.h>
+
+#include "mali_kernel_linux.h"
+#ifdef CONFIG_PM_RUNTIME
+#include <linux/pm_runtime.h>
+#endif /* CONFIG_PM_RUNTIME */
+#include <linux/platform_device.h>
+#include <linux/version.h>
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+/* Can NOT run in atomic context */
+_mali_osk_errcode_t _mali_osk_pm_dev_ref_get_sync(void)
+{
+#ifdef CONFIG_PM_RUNTIME
+	int err;
+	MALI_DEBUG_ASSERT_POINTER(mali_platform_device);
+	err = pm_runtime_get_sync(&(mali_platform_device->dev));
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 37))
+	pm_runtime_mark_last_busy(&(mali_platform_device->dev));
+#endif
+	if (0 > err) {
+		MALI_PRINT_ERROR(("Mali OSK PM: pm_runtime_get_sync() returned error code %d\n", err));
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif
+	return _MALI_OSK_ERR_OK;
+}
+
+/* Can run in atomic context */
+_mali_osk_errcode_t _mali_osk_pm_dev_ref_get_async(void)
+{
+#ifdef CONFIG_PM_RUNTIME
+	int err;
+	MALI_DEBUG_ASSERT_POINTER(mali_platform_device);
+	err = pm_runtime_get(&(mali_platform_device->dev));
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 37))
+	pm_runtime_mark_last_busy(&(mali_platform_device->dev));
+#endif
+	if (0 > err && -EINPROGRESS != err) {
+		MALI_PRINT_ERROR(("Mali OSK PM: pm_runtime_get() returned error code %d\n", err));
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif
+	return _MALI_OSK_ERR_OK;
+}
+
+
+/* Can run in atomic context */
+void _mali_osk_pm_dev_ref_put(void)
+{
+#ifdef CONFIG_PM_RUNTIME
+	MALI_DEBUG_ASSERT_POINTER(mali_platform_device);
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 37))
+	pm_runtime_mark_last_busy(&(mali_platform_device->dev));
+	pm_runtime_put_autosuspend(&(mali_platform_device->dev));
+#else
+	pm_runtime_put(&(mali_platform_device->dev));
+#endif
+#endif
+}
+
+void _mali_osk_pm_dev_barrier(void)
+{
+#ifdef CONFIG_PM_RUNTIME
+	pm_runtime_barrier(&(mali_platform_device->dev));
+#endif
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_profiling.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_profiling.c
@@ -0,0 +1,1282 @@
+/*
+ * Copyright (C) 2012-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/hrtimer.h>
+#include <linux/module.h>
+#include <linux/file.h>
+#include <linux/poll.h>
+#include <linux/anon_inodes.h>
+#include <linux/sched.h>
+
+#include <mali_profiling_gator_api.h>
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_ukk.h"
+#include "mali_uk_types.h"
+#include "mali_osk_profiling.h"
+#include "mali_linux_trace.h"
+#include "mali_gp.h"
+#include "mali_pp.h"
+#include "mali_l2_cache.h"
+#include "mali_user_settings_db.h"
+#include "mali_executor.h"
+#include "mali_memory_manager.h"
+
+#define MALI_PROFILING_STREAM_DATA_DEFAULT_SIZE 100
+#define MALI_PROFILING_STREAM_HOLD_TIME 1000000         /*1 ms */
+
+#define MALI_PROFILING_STREAM_BUFFER_SIZE       (1 << 12)
+#define MALI_PROFILING_STREAM_BUFFER_NUM        100
+
+/**
+ * Define the mali profiling stream struct.
+ */
+typedef struct mali_profiling_stream {
+	u8 data[MALI_PROFILING_STREAM_BUFFER_SIZE];
+	u32 used_size;
+	struct list_head list;
+} mali_profiling_stream;
+
+typedef struct mali_profiling_stream_list {
+	spinlock_t spin_lock;
+	struct list_head free_list;
+	struct list_head queue_list;
+} mali_profiling_stream_list;
+
+static const char mali_name[] = "4xx";
+static const char utgard_setup_version[] = "ANNOTATE_SETUP 1\n";
+
+static u32 profiling_sample_rate = 0;
+static u32 first_sw_counter_index = 0;
+
+static mali_bool l2_cache_counter_if_enabled = MALI_FALSE;
+static u32 num_counters_enabled = 0;
+static u32 mem_counters_enabled = 0;
+
+static _mali_osk_atomic_t stream_fd_if_used;
+
+static wait_queue_head_t stream_fd_wait_queue;
+static mali_profiling_counter *global_mali_profiling_counters = NULL;
+static u32 num_global_mali_profiling_counters = 0;
+
+static mali_profiling_stream_list *global_mali_stream_list = NULL;
+static mali_profiling_stream *mali_counter_stream = NULL;
+static mali_profiling_stream *mali_core_activity_stream = NULL;
+static u64 mali_core_activity_stream_dequeue_time = 0;
+static spinlock_t mali_activity_lock;
+static u32 mali_activity_cores_num =  0;
+static struct hrtimer profiling_sampling_timer;
+
+const char *_mali_mem_counter_descriptions[] = _MALI_MEM_COUTNER_DESCRIPTIONS;
+const char *_mali_special_counter_descriptions[] = _MALI_SPCIAL_COUNTER_DESCRIPTIONS;
+
+static u32 current_profiling_pid = 0;
+
+static void _mali_profiling_stream_list_destory(mali_profiling_stream_list *profiling_stream_list)
+{
+	mali_profiling_stream *profiling_stream, *tmp_profiling_stream;
+	MALI_DEBUG_ASSERT_POINTER(profiling_stream_list);
+
+	list_for_each_entry_safe(profiling_stream, tmp_profiling_stream, &profiling_stream_list->free_list, list) {
+		list_del(&profiling_stream->list);
+		kfree(profiling_stream);
+	}
+
+	list_for_each_entry_safe(profiling_stream, tmp_profiling_stream, &profiling_stream_list->queue_list, list) {
+		list_del(&profiling_stream->list);
+		kfree(profiling_stream);
+	}
+
+	kfree(profiling_stream_list);
+}
+
+static void _mali_profiling_global_stream_list_free(void)
+{
+	mali_profiling_stream *profiling_stream, *tmp_profiling_stream;
+	unsigned long irq_flags;
+
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+	spin_lock_irqsave(&global_mali_stream_list->spin_lock, irq_flags);
+	list_for_each_entry_safe(profiling_stream, tmp_profiling_stream, &global_mali_stream_list->queue_list, list) {
+		profiling_stream->used_size = 0;
+		list_move(&profiling_stream->list, &global_mali_stream_list->free_list);
+	}
+	spin_unlock_irqrestore(&global_mali_stream_list->spin_lock, irq_flags);
+}
+
+static _mali_osk_errcode_t _mali_profiling_global_stream_list_dequeue(struct list_head *stream_list, mali_profiling_stream **new_mali_profiling_stream)
+{
+	unsigned long irq_flags;
+	_mali_osk_errcode_t ret = _MALI_OSK_ERR_OK;
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+	MALI_DEBUG_ASSERT_POINTER(stream_list);
+
+	spin_lock_irqsave(&global_mali_stream_list->spin_lock, irq_flags);
+
+	if (!list_empty(stream_list)) {
+		*new_mali_profiling_stream = list_entry(stream_list->next, mali_profiling_stream, list);
+		list_del_init(&(*new_mali_profiling_stream)->list);
+	} else {
+		ret = _MALI_OSK_ERR_NOMEM;
+	}
+
+	spin_unlock_irqrestore(&global_mali_stream_list->spin_lock, irq_flags);
+
+	return ret;
+}
+
+static void _mali_profiling_global_stream_list_queue(struct list_head *stream_list, mali_profiling_stream *current_mali_profiling_stream)
+{
+	unsigned long irq_flags;
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+	MALI_DEBUG_ASSERT_POINTER(stream_list);
+
+	spin_lock_irqsave(&global_mali_stream_list->spin_lock, irq_flags);
+	list_add_tail(&current_mali_profiling_stream->list, stream_list);
+	spin_unlock_irqrestore(&global_mali_stream_list->spin_lock, irq_flags);
+}
+
+static mali_bool _mali_profiling_global_stream_queue_list_if_empty(void)
+{
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+	return list_empty(&global_mali_stream_list->queue_list);
+}
+
+static u32 _mali_profiling_global_stream_queue_list_next_size(void)
+{
+	unsigned long irq_flags;
+	u32 size = 0;
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+
+	spin_lock_irqsave(&global_mali_stream_list->spin_lock, irq_flags);
+	if (!list_empty(&global_mali_stream_list->queue_list)) {
+		mali_profiling_stream *next_mali_profiling_stream =
+			list_entry(global_mali_stream_list->queue_list.next, mali_profiling_stream, list);
+		size = next_mali_profiling_stream->used_size;
+	}
+	spin_unlock_irqrestore(&global_mali_stream_list->spin_lock, irq_flags);
+	return size;
+}
+
+/* The mali profiling stream file operations functions. */
+static ssize_t _mali_profiling_stream_read(
+	struct file *filp,
+	char __user *buffer,
+	size_t      size,
+	loff_t      *f_pos);
+
+static unsigned int  _mali_profiling_stream_poll(struct file *filp, poll_table *wait);
+
+static int  _mali_profiling_stream_release(struct inode *inode, struct file *filp);
+
+/* The timeline stream file operations structure. */
+static const struct file_operations mali_profiling_stream_fops = {
+	.release = _mali_profiling_stream_release,
+	.read    = _mali_profiling_stream_read,
+	.poll    = _mali_profiling_stream_poll,
+};
+
+static ssize_t _mali_profiling_stream_read(
+	struct file *filp,
+	char __user *buffer,
+	size_t      size,
+	loff_t      *f_pos)
+{
+	u32 copy_len = 0;
+	mali_profiling_stream *current_mali_profiling_stream;
+	u32 used_size;
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+
+	while (!_mali_profiling_global_stream_queue_list_if_empty()) {
+		used_size = _mali_profiling_global_stream_queue_list_next_size();
+		if (used_size <= ((u32)size - copy_len)) {
+			current_mali_profiling_stream = NULL;
+			_mali_profiling_global_stream_list_dequeue(&global_mali_stream_list->queue_list,
+					&current_mali_profiling_stream);
+			MALI_DEBUG_ASSERT_POINTER(current_mali_profiling_stream);
+			if (copy_to_user(&buffer[copy_len], current_mali_profiling_stream->data, current_mali_profiling_stream->used_size)) {
+				current_mali_profiling_stream->used_size = 0;
+				_mali_profiling_global_stream_list_queue(&global_mali_stream_list->free_list, current_mali_profiling_stream);
+				return -EFAULT;
+			}
+			copy_len += current_mali_profiling_stream->used_size;
+			current_mali_profiling_stream->used_size = 0;
+			_mali_profiling_global_stream_list_queue(&global_mali_stream_list->free_list, current_mali_profiling_stream);
+		} else {
+			break;
+		}
+	}
+	return (ssize_t)copy_len;
+}
+
+static unsigned int  _mali_profiling_stream_poll(struct file *filp, poll_table *wait)
+{
+	poll_wait(filp, &stream_fd_wait_queue, wait);
+	if (!_mali_profiling_global_stream_queue_list_if_empty())
+		return POLLIN;
+	return 0;
+}
+
+static int  _mali_profiling_stream_release(struct inode *inode, struct file *filp)
+{
+	_mali_osk_atomic_init(&stream_fd_if_used, 0);
+	return 0;
+}
+
+/* The funs for control packet and stream data.*/
+static void _mali_profiling_set_packet_size(unsigned char *const buf, const u32 size)
+{
+	u32 i;
+
+	for (i = 0; i < sizeof(size); ++i)
+		buf[i] = (size >> 8 * i) & 0xFF;
+}
+
+static u32 _mali_profiling_get_packet_size(unsigned char *const buf)
+{
+	u32 i;
+	u32 size = 0;
+	for (i = 0; i < sizeof(size); ++i)
+		size |= (u32)buf[i] << 8 * i;
+	return size;
+}
+
+static u32 _mali_profiling_read_packet_int(unsigned char *const buf, u32 *const pos, u32 const packet_size)
+{
+	u64 int_value = 0;
+	u8 shift = 0;
+	u8 byte_value = ~0;
+
+	while ((byte_value & 0x80) != 0) {
+		if ((*pos) >= packet_size)
+			return -1;
+		byte_value = buf[*pos];
+		*pos += 1;
+		int_value |= (u32)(byte_value & 0x7f) << shift;
+		shift += 7;
+	}
+
+	if (shift < 8 * sizeof(int_value) && (byte_value & 0x40) != 0) {
+		int_value |= -(1 << shift);
+	}
+
+	return int_value;
+}
+
+static u32 _mali_profiling_pack_int(u8 *const buf, u32 const buf_size, u32 const pos, s32 value)
+{
+	u32 add_bytes = 0;
+	int more = 1;
+	while (more) {
+		/* low order 7 bits of val */
+		char byte_value = value & 0x7f;
+		value >>= 7;
+
+		if ((value == 0 && (byte_value & 0x40) == 0) || (value == -1 && (byte_value & 0x40) != 0)) {
+			more = 0;
+		} else {
+			byte_value |= 0x80;
+		}
+
+		if ((pos + add_bytes) >= buf_size)
+			return 0;
+		buf[pos + add_bytes] = byte_value;
+		add_bytes++;
+	}
+
+	return add_bytes;
+}
+
+static int _mali_profiling_pack_long(uint8_t *const buf, u32 const buf_size, u32 const pos, s64 val)
+{
+	int add_bytes = 0;
+	int more = 1;
+	while (more) {
+		/* low order 7 bits of x */
+		char byte_value = val & 0x7f;
+		val >>= 7;
+
+		if ((val == 0 && (byte_value & 0x40) == 0) || (val == -1 && (byte_value & 0x40) != 0)) {
+			more = 0;
+		} else {
+			byte_value |= 0x80;
+		}
+
+		MALI_DEBUG_ASSERT((pos + add_bytes) < buf_size);
+		buf[pos + add_bytes] = byte_value;
+		add_bytes++;
+	}
+
+	return add_bytes;
+}
+
+static void _mali_profiling_stream_add_counter(mali_profiling_stream *profiling_stream, s64 current_time, u32 key, u32 counter_value)
+{
+	u32 add_size = STREAM_HEADER_SIZE;
+	MALI_DEBUG_ASSERT_POINTER(profiling_stream);
+	MALI_DEBUG_ASSERT((profiling_stream->used_size) < MALI_PROFILING_STREAM_BUFFER_SIZE);
+
+	profiling_stream->data[profiling_stream->used_size] = STREAM_HEADER_COUNTER_VALUE;
+
+	add_size += _mali_profiling_pack_long(profiling_stream->data, MALI_PROFILING_STREAM_BUFFER_SIZE,
+					      profiling_stream->used_size + add_size, current_time);
+	add_size += _mali_profiling_pack_int(profiling_stream->data, MALI_PROFILING_STREAM_BUFFER_SIZE,
+					     profiling_stream->used_size + add_size, (s32)0);
+	add_size += _mali_profiling_pack_int(profiling_stream->data, MALI_PROFILING_STREAM_BUFFER_SIZE,
+					     profiling_stream->used_size + add_size, (s32)key);
+	add_size += _mali_profiling_pack_int(profiling_stream->data, MALI_PROFILING_STREAM_BUFFER_SIZE,
+					     profiling_stream->used_size + add_size, (s32)counter_value);
+
+	_mali_profiling_set_packet_size(profiling_stream->data + profiling_stream->used_size + 1,
+					add_size - STREAM_HEADER_SIZE);
+
+	profiling_stream->used_size += add_size;
+}
+
+/* The callback function for sampling timer.*/
+static enum hrtimer_restart  _mali_profiling_sampling_counters(struct hrtimer *timer)
+{
+	u32 counter_index;
+	s64 current_time;
+	MALI_DEBUG_ASSERT_POINTER(global_mali_profiling_counters);
+	MALI_DEBUG_ASSERT_POINTER(global_mali_stream_list);
+
+	MALI_DEBUG_ASSERT(NULL == mali_counter_stream);
+	if (_MALI_OSK_ERR_OK == _mali_profiling_global_stream_list_dequeue(
+		    &global_mali_stream_list->free_list, &mali_counter_stream)) {
+
+		MALI_DEBUG_ASSERT_POINTER(mali_counter_stream);
+		MALI_DEBUG_ASSERT(0 == mali_counter_stream->used_size);
+
+		/* Capture l2 cache counter values if enabled */
+		if (MALI_TRUE == l2_cache_counter_if_enabled) {
+			int i, j = 0;
+			_mali_profiling_l2_counter_values l2_counters_values;
+			_mali_profiling_get_l2_counters(&l2_counters_values);
+
+			for (i  = COUNTER_L2_0_C0; i <= COUNTER_L2_2_C1; i++) {
+				if (0 == (j % 2))
+					_mali_osk_profiling_record_global_counters(i, l2_counters_values.cores[j / 2].value0);
+				else
+					_mali_osk_profiling_record_global_counters(i, l2_counters_values.cores[j / 2].value1);
+				j++;
+			}
+		}
+
+		current_time = (s64)_mali_osk_boot_time_get_ns();
+
+		/* Add all enabled counter values into stream */
+		for (counter_index = 0; counter_index < num_global_mali_profiling_counters; counter_index++) {
+			/* No need to sample these couners here. */
+			if (global_mali_profiling_counters[counter_index].enabled) {
+				if ((global_mali_profiling_counters[counter_index].counter_id >= FIRST_MEM_COUNTER &&
+				     global_mali_profiling_counters[counter_index].counter_id <= LAST_MEM_COUNTER)
+				    || (global_mali_profiling_counters[counter_index].counter_id == COUNTER_VP_ACTIVITY)
+				    || (global_mali_profiling_counters[counter_index].counter_id == COUNTER_FP_ACTIVITY)
+				    || (global_mali_profiling_counters[counter_index].counter_id == COUNTER_FILMSTRIP)) {
+
+					continue;
+				}
+
+				if (global_mali_profiling_counters[counter_index].counter_id >= COUNTER_L2_0_C0 &&
+				    global_mali_profiling_counters[counter_index].counter_id <= COUNTER_L2_2_C1) {
+
+					u32 prev_val = global_mali_profiling_counters[counter_index].prev_counter_value;
+
+					_mali_profiling_stream_add_counter(mali_counter_stream, current_time, global_mali_profiling_counters[counter_index].key,
+									   global_mali_profiling_counters[counter_index].current_counter_value - prev_val);
+
+					prev_val = global_mali_profiling_counters[counter_index].current_counter_value;
+
+					global_mali_profiling_counters[counter_index].prev_counter_value = prev_val;
+				} else {
+
+					if (global_mali_profiling_counters[counter_index].counter_id == COUNTER_TOTAL_ALLOC_PAGES) {
+						u32 total_alloc_mem = _mali_ukk_report_memory_usage();
+						global_mali_profiling_counters[counter_index].current_counter_value = total_alloc_mem / _MALI_OSK_MALI_PAGE_SIZE;
+					}
+					_mali_profiling_stream_add_counter(mali_counter_stream, current_time, global_mali_profiling_counters[counter_index].key,
+									   global_mali_profiling_counters[counter_index].current_counter_value);
+					if (global_mali_profiling_counters[counter_index].counter_id < FIRST_SPECIAL_COUNTER)
+						global_mali_profiling_counters[counter_index].current_counter_value = 0;
+				}
+			}
+		}
+		_mali_profiling_global_stream_list_queue(&global_mali_stream_list->queue_list, mali_counter_stream);
+		mali_counter_stream = NULL;
+	} else {
+		MALI_DEBUG_PRINT(1, ("Not enough mali profiling stream buffer!\n"));
+	}
+
+	wake_up_interruptible(&stream_fd_wait_queue);
+
+	/*Enable the sampling timer again*/
+	if (0 != num_counters_enabled && 0 != profiling_sample_rate) {
+		hrtimer_forward_now(&profiling_sampling_timer, ns_to_ktime(profiling_sample_rate));
+		return HRTIMER_RESTART;
+	}
+	return HRTIMER_NORESTART;
+}
+
+static void _mali_profiling_sampling_core_activity_switch(int counter_id, int core, u32 activity, u32 pid)
+{
+	unsigned long irq_flags;
+
+	spin_lock_irqsave(&mali_activity_lock, irq_flags);
+	if (activity == 0)
+		mali_activity_cores_num--;
+	else
+		mali_activity_cores_num++;
+	spin_unlock_irqrestore(&mali_activity_lock, irq_flags);
+
+	if (NULL != global_mali_profiling_counters) {
+		int i ;
+		for (i = 0; i < num_global_mali_profiling_counters; i++) {
+			if (counter_id == global_mali_profiling_counters[i].counter_id && global_mali_profiling_counters[i].enabled) {
+				u64 current_time = _mali_osk_boot_time_get_ns();
+				u32 add_size = STREAM_HEADER_SIZE;
+
+				if (NULL != mali_core_activity_stream) {
+					if ((mali_core_activity_stream_dequeue_time +  MALI_PROFILING_STREAM_HOLD_TIME < current_time) ||
+					    (MALI_PROFILING_STREAM_DATA_DEFAULT_SIZE > MALI_PROFILING_STREAM_BUFFER_SIZE
+					     - mali_core_activity_stream->used_size)) {
+						_mali_profiling_global_stream_list_queue(&global_mali_stream_list->queue_list, mali_core_activity_stream);
+						mali_core_activity_stream = NULL;
+						wake_up_interruptible(&stream_fd_wait_queue);
+					}
+				}
+
+				if (NULL == mali_core_activity_stream) {
+					if (_MALI_OSK_ERR_OK == _mali_profiling_global_stream_list_dequeue(
+						    &global_mali_stream_list->free_list, &mali_core_activity_stream)) {
+						mali_core_activity_stream_dequeue_time = current_time;
+					} else {
+						MALI_DEBUG_PRINT(1, ("Not enough mali profiling stream buffer!\n"));
+						wake_up_interruptible(&stream_fd_wait_queue);
+						break;
+					}
+
+				}
+
+				mali_core_activity_stream->data[mali_core_activity_stream->used_size] = STREAM_HEADER_CORE_ACTIVITY;
+
+				add_size += _mali_profiling_pack_long(mali_core_activity_stream->data,
+								      MALI_PROFILING_STREAM_BUFFER_SIZE, mali_core_activity_stream->used_size + add_size, (s64)current_time);
+				add_size += _mali_profiling_pack_int(mali_core_activity_stream->data,
+								     MALI_PROFILING_STREAM_BUFFER_SIZE, mali_core_activity_stream->used_size + add_size, core);
+				add_size += _mali_profiling_pack_int(mali_core_activity_stream->data,
+								     MALI_PROFILING_STREAM_BUFFER_SIZE, mali_core_activity_stream->used_size + add_size, (s32)global_mali_profiling_counters[i].key);
+				add_size += _mali_profiling_pack_int(mali_core_activity_stream->data,
+								     MALI_PROFILING_STREAM_BUFFER_SIZE, mali_core_activity_stream->used_size + add_size, activity);
+				add_size += _mali_profiling_pack_int(mali_core_activity_stream->data,
+								     MALI_PROFILING_STREAM_BUFFER_SIZE, mali_core_activity_stream->used_size + add_size, pid);
+
+				_mali_profiling_set_packet_size(mali_core_activity_stream->data + mali_core_activity_stream->used_size + 1,
+								add_size - STREAM_HEADER_SIZE);
+
+				mali_core_activity_stream->used_size += add_size;
+
+				if (0 == mali_activity_cores_num) {
+					_mali_profiling_global_stream_list_queue(&global_mali_stream_list->queue_list, mali_core_activity_stream);
+					mali_core_activity_stream = NULL;
+					wake_up_interruptible(&stream_fd_wait_queue);
+				}
+
+				break;
+			}
+		}
+	}
+}
+
+static mali_bool _mali_profiling_global_counters_init(void)
+{
+	int core_id, counter_index, counter_number, counter_id;
+	u32 num_l2_cache_cores;
+	u32 num_pp_cores;
+	u32 num_gp_cores = 1;
+
+	MALI_DEBUG_ASSERT(NULL == global_mali_profiling_counters);
+	num_pp_cores = mali_pp_get_glob_num_pp_cores();
+	num_l2_cache_cores =    mali_l2_cache_core_get_glob_num_l2_cores();
+
+	num_global_mali_profiling_counters = 3 * (num_gp_cores + num_pp_cores) + 2 * num_l2_cache_cores
+					     + MALI_PROFILING_SW_COUNTERS_NUM
+					     + MALI_PROFILING_SPECIAL_COUNTERS_NUM
+					     + MALI_PROFILING_MEM_COUNTERS_NUM;
+	global_mali_profiling_counters = _mali_osk_calloc(num_global_mali_profiling_counters, sizeof(mali_profiling_counter));
+
+	if (NULL == global_mali_profiling_counters)
+		return MALI_FALSE;
+
+	counter_index = 0;
+	/*Vertex processor counters */
+	for (core_id = 0; core_id < num_gp_cores; core_id ++) {
+		global_mali_profiling_counters[counter_index].counter_id = ACTIVITY_VP_0 + core_id;
+		_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+				   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_VP_%d_active", mali_name, core_id);
+
+		for (counter_number = 0; counter_number < 2; counter_number++) {
+			counter_index++;
+			global_mali_profiling_counters[counter_index].counter_id = COUNTER_VP_0_C0 + (2 * core_id) + counter_number;
+			_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+					   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_VP_%d_cnt%d", mali_name, core_id, counter_number);
+		}
+	}
+
+	/* Fragment processors' counters */
+	for (core_id = 0; core_id < num_pp_cores; core_id++) {
+		counter_index++;
+		global_mali_profiling_counters[counter_index].counter_id = ACTIVITY_FP_0 + core_id;
+		_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+				   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_FP_%d_active", mali_name, core_id);
+
+		for (counter_number = 0; counter_number < 2; counter_number++) {
+			counter_index++;
+			global_mali_profiling_counters[counter_index].counter_id = COUNTER_FP_0_C0 + (2 * core_id) + counter_number;
+			_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+					   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_FP_%d_cnt%d", mali_name, core_id, counter_number);
+		}
+	}
+
+	/* L2 Cache counters */
+	for (core_id = 0; core_id < num_l2_cache_cores; core_id++) {
+		for (counter_number = 0; counter_number < 2; counter_number++) {
+			counter_index++;
+			global_mali_profiling_counters[counter_index].counter_id = COUNTER_L2_0_C0 + (2 * core_id) + counter_number;
+			_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+					   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_L2_%d_cnt%d", mali_name, core_id, counter_number);
+		}
+	}
+
+	/* Now set up the software counter entries */
+	for (counter_id = FIRST_SW_COUNTER; counter_id <= LAST_SW_COUNTER; counter_id++) {
+		counter_index++;
+
+		if (0 == first_sw_counter_index)
+			first_sw_counter_index = counter_index;
+
+		global_mali_profiling_counters[counter_index].counter_id = counter_id;
+		_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+				   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_SW_%d", mali_name, counter_id - FIRST_SW_COUNTER);
+	}
+
+	/* Now set up the special counter entries */
+	for (counter_id = FIRST_SPECIAL_COUNTER; counter_id <= LAST_SPECIAL_COUNTER; counter_id++) {
+
+		counter_index++;
+		_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+				   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_%s",
+				   mali_name, _mali_special_counter_descriptions[counter_id - FIRST_SPECIAL_COUNTER]);
+
+		global_mali_profiling_counters[counter_index].counter_id = counter_id;
+	}
+
+	/* Now set up the mem counter entries*/
+	for (counter_id = FIRST_MEM_COUNTER; counter_id <= LAST_MEM_COUNTER; counter_id++) {
+
+		counter_index++;
+		_mali_osk_snprintf(global_mali_profiling_counters[counter_index].counter_name,
+				   sizeof(global_mali_profiling_counters[counter_index].counter_name), "ARM_Mali-%s_%s",
+				   mali_name, _mali_mem_counter_descriptions[counter_id - FIRST_MEM_COUNTER]);
+
+		global_mali_profiling_counters[counter_index].counter_id = counter_id;
+	}
+
+	MALI_DEBUG_ASSERT((counter_index + 1) == num_global_mali_profiling_counters);
+
+	return MALI_TRUE;
+}
+
+void _mali_profiling_notification_mem_counter(struct mali_session_data *session, u32 counter_id, u32 key, int enable)
+{
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (NULL != session) {
+		_mali_osk_notification_t *notification;
+		_mali_osk_notification_queue_t *queue;
+
+		queue = session->ioctl_queue;
+		MALI_DEBUG_ASSERT(NULL != queue);
+
+		notification = _mali_osk_notification_create(_MALI_NOTIFICATION_ANNOTATE_PROFILING_MEM_COUNTER,
+				sizeof(_mali_uk_annotate_profiling_mem_counter_s));
+
+		if (NULL != notification) {
+			_mali_uk_annotate_profiling_mem_counter_s *data = notification->result_buffer;
+			data->counter_id = counter_id;
+			data->key = key;
+			data->enable = enable;
+
+			_mali_osk_notification_queue_send(queue, notification);
+		} else {
+			MALI_PRINT_ERROR(("Failed to create notification object!\n"));
+		}
+	} else {
+		MALI_PRINT_ERROR(("Failed to find the right session!\n"));
+	}
+}
+
+void _mali_profiling_notification_enable(struct mali_session_data *session, u32 sampling_rate, int enable)
+{
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (NULL != session) {
+		_mali_osk_notification_t *notification;
+		_mali_osk_notification_queue_t *queue;
+
+		queue = session->ioctl_queue;
+		MALI_DEBUG_ASSERT(NULL != queue);
+
+		notification = _mali_osk_notification_create(_MALI_NOTIFICATION_ANNOTATE_PROFILING_ENABLE,
+				sizeof(_mali_uk_annotate_profiling_enable_s));
+
+		if (NULL != notification) {
+			_mali_uk_annotate_profiling_enable_s *data = notification->result_buffer;
+			data->sampling_rate = sampling_rate;
+			data->enable = enable;
+
+			_mali_osk_notification_queue_send(queue, notification);
+		} else {
+			MALI_PRINT_ERROR(("Failed to create notification object!\n"));
+		}
+	} else {
+		MALI_PRINT_ERROR(("Failed to find the right session!\n"));
+	}
+}
+
+
+_mali_osk_errcode_t _mali_osk_profiling_init(mali_bool auto_start)
+{
+	int i;
+	mali_profiling_stream *new_mali_profiling_stream = NULL;
+	mali_profiling_stream_list *new_mali_profiling_stream_list = NULL;
+	if (MALI_TRUE == auto_start) {
+		mali_set_user_setting(_MALI_UK_USER_SETTING_SW_EVENTS_ENABLE, MALI_TRUE);
+	}
+
+	/*Init the global_mali_stream_list*/
+	MALI_DEBUG_ASSERT(NULL == global_mali_stream_list);
+	new_mali_profiling_stream_list = (mali_profiling_stream_list *)kmalloc(sizeof(mali_profiling_stream_list), GFP_KERNEL);
+
+	if (NULL == new_mali_profiling_stream_list) {
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	spin_lock_init(&new_mali_profiling_stream_list->spin_lock);
+	INIT_LIST_HEAD(&new_mali_profiling_stream_list->free_list);
+	INIT_LIST_HEAD(&new_mali_profiling_stream_list->queue_list);
+
+	spin_lock_init(&mali_activity_lock);
+	mali_activity_cores_num =  0;
+
+	for (i = 0; i < MALI_PROFILING_STREAM_BUFFER_NUM; i++) {
+		new_mali_profiling_stream = (mali_profiling_stream *)kmalloc(sizeof(mali_profiling_stream), GFP_KERNEL);
+		if (NULL == new_mali_profiling_stream) {
+			_mali_profiling_stream_list_destory(new_mali_profiling_stream_list);
+			return _MALI_OSK_ERR_NOMEM;
+		}
+
+		INIT_LIST_HEAD(&new_mali_profiling_stream->list);
+		new_mali_profiling_stream->used_size = 0;
+		list_add_tail(&new_mali_profiling_stream->list, &new_mali_profiling_stream_list->free_list);
+
+	}
+
+	_mali_osk_atomic_init(&stream_fd_if_used, 0);
+	init_waitqueue_head(&stream_fd_wait_queue);
+
+	hrtimer_init(&profiling_sampling_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+
+	profiling_sampling_timer.function = _mali_profiling_sampling_counters;
+
+	global_mali_stream_list = new_mali_profiling_stream_list;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void _mali_osk_profiling_term(void)
+{
+	if (0 != profiling_sample_rate) {
+		hrtimer_cancel(&profiling_sampling_timer);
+		profiling_sample_rate = 0;
+	}
+	_mali_osk_atomic_term(&stream_fd_if_used);
+
+	if (NULL != global_mali_profiling_counters) {
+		_mali_osk_free(global_mali_profiling_counters);
+		global_mali_profiling_counters = NULL;
+		num_global_mali_profiling_counters = 0;
+	}
+
+	if (NULL != global_mali_stream_list) {
+		_mali_profiling_stream_list_destory(global_mali_stream_list);
+		global_mali_stream_list = NULL;
+	}
+
+}
+
+void _mali_osk_profiling_stop_sampling(u32 pid)
+{
+	if (pid == current_profiling_pid) {
+
+		int i;
+		/* Reset all counter states when closing connection.*/
+		for (i = 0; i < num_global_mali_profiling_counters; ++i) {
+			_mali_profiling_set_event(global_mali_profiling_counters[i].counter_id, MALI_HW_CORE_NO_COUNTER);
+			global_mali_profiling_counters[i].enabled = 0;
+			global_mali_profiling_counters[i].prev_counter_value = 0;
+			global_mali_profiling_counters[i].current_counter_value = 0;
+		}
+		l2_cache_counter_if_enabled = MALI_FALSE;
+		num_counters_enabled = 0;
+		mem_counters_enabled = 0;
+		_mali_profiling_control(FBDUMP_CONTROL_ENABLE, 0);
+		_mali_profiling_control(SW_COUNTER_ENABLE, 0);
+		/* Delete sampling timer when closing connection. */
+		if (0 != profiling_sample_rate) {
+			hrtimer_cancel(&profiling_sampling_timer);
+			profiling_sample_rate = 0;
+		}
+		current_profiling_pid = 0;
+	}
+}
+
+void    _mali_osk_profiling_add_event(u32 event_id, u32 data0, u32 data1, u32 data2, u32 data3, u32 data4)
+{
+	/*Record the freq & volt to global_mali_profiling_counters here. */
+	if (0 != profiling_sample_rate) {
+		u32 channel;
+		u32 state;
+		channel = (event_id >> 16) & 0xFF;
+		state = ((event_id >> 24) & 0xF) << 24;
+
+		switch (state) {
+		case MALI_PROFILING_EVENT_TYPE_SINGLE:
+			if ((MALI_PROFILING_EVENT_CHANNEL_GPU >> 16) == channel) {
+				u32 reason = (event_id & 0xFFFF);
+				if (MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE == reason) {
+					_mali_osk_profiling_record_global_counters(COUNTER_FREQUENCY, data0);
+					_mali_osk_profiling_record_global_counters(COUNTER_VOLTAGE, data1);
+				}
+			}
+			break;
+		case MALI_PROFILING_EVENT_TYPE_START:
+			if ((MALI_PROFILING_EVENT_CHANNEL_GP0 >> 16) == channel) {
+				_mali_profiling_sampling_core_activity_switch(COUNTER_VP_ACTIVITY, 0, 1, data1);
+			} else if (channel >= (MALI_PROFILING_EVENT_CHANNEL_PP0 >> 16) &&
+				   (MALI_PROFILING_EVENT_CHANNEL_PP7 >> 16) >= channel) {
+				u32 core_id = channel - (MALI_PROFILING_EVENT_CHANNEL_PP0 >> 16);
+				_mali_profiling_sampling_core_activity_switch(COUNTER_FP_ACTIVITY, core_id, 1, data1);
+			}
+			break;
+		case MALI_PROFILING_EVENT_TYPE_STOP:
+			if ((MALI_PROFILING_EVENT_CHANNEL_GP0 >> 16) == channel) {
+				_mali_profiling_sampling_core_activity_switch(COUNTER_VP_ACTIVITY, 0, 0, 0);
+			} else if (channel >= (MALI_PROFILING_EVENT_CHANNEL_PP0 >> 16) &&
+				   (MALI_PROFILING_EVENT_CHANNEL_PP7 >> 16) >= channel) {
+				u32 core_id = channel - (MALI_PROFILING_EVENT_CHANNEL_PP0 >> 16);
+				_mali_profiling_sampling_core_activity_switch(COUNTER_FP_ACTIVITY, core_id, 0, 0);
+			}
+			break;
+		default:
+			break;
+		}
+	}
+	trace_mali_timeline_event(event_id, data0, data1, data2, data3, data4);
+}
+
+void _mali_osk_profiling_report_sw_counters(u32 *counters)
+{
+	trace_mali_sw_counters(_mali_osk_get_pid(), _mali_osk_get_tid(), NULL, counters);
+}
+
+void _mali_osk_profiling_record_global_counters(int counter_id, u32 value)
+{
+	if (NULL != global_mali_profiling_counters) {
+		int i ;
+		for (i = 0; i < num_global_mali_profiling_counters; i++) {
+			if (counter_id == global_mali_profiling_counters[i].counter_id && global_mali_profiling_counters[i].enabled) {
+				global_mali_profiling_counters[i].current_counter_value = value;
+				break;
+			}
+		}
+	}
+}
+
+_mali_osk_errcode_t _mali_ukk_profiling_add_event(_mali_uk_profiling_add_event_s *args)
+{
+	/* Always add process and thread identificator in the first two data elements for events from user space */
+	_mali_osk_profiling_add_event(args->event_id, _mali_osk_get_pid(), _mali_osk_get_tid(), args->data[2], args->data[3], args->data[4]);
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_sw_counters_report(_mali_uk_sw_counters_report_s *args)
+{
+	u32 *counters = (u32 *)(uintptr_t)args->counters;
+
+	_mali_osk_profiling_report_sw_counters(counters);
+
+	if (NULL != global_mali_profiling_counters) {
+		int i;
+		for (i = 0; i < MALI_PROFILING_SW_COUNTERS_NUM; i ++) {
+			if (global_mali_profiling_counters[first_sw_counter_index + i].enabled) {
+				global_mali_profiling_counters[first_sw_counter_index + i].current_counter_value = *(counters + i);
+			}
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_profiling_stream_fd_get(_mali_uk_profiling_stream_fd_get_s *args)
+{
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (1 == _mali_osk_atomic_inc_return(&stream_fd_if_used)) {
+
+		s32 fd = anon_inode_getfd("[mali_profiling_stream]", &mali_profiling_stream_fops,
+					  session,
+					  O_RDONLY | O_CLOEXEC);
+
+		args->stream_fd = fd;
+		if (0 > fd) {
+			_mali_osk_atomic_dec(&stream_fd_if_used);
+			return _MALI_OSK_ERR_FAULT;
+		}
+		args->stream_fd = fd;
+	} else {
+		_mali_osk_atomic_dec(&stream_fd_if_used);
+		args->stream_fd = -1;
+		return _MALI_OSK_ERR_BUSY;
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_ukk_profiling_control_set(_mali_uk_profiling_control_set_s *args)
+{
+	u32 control_packet_size;
+	u32 output_buffer_size;
+
+	struct  mali_session_data *session = (struct mali_session_data *)(uintptr_t)args->ctx;
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (NULL == global_mali_profiling_counters && MALI_FALSE == _mali_profiling_global_counters_init()) {
+		MALI_PRINT_ERROR(("Failed to create global_mali_profiling_counters.\n"));
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	control_packet_size = args->control_packet_size;
+	output_buffer_size = args->response_packet_size;
+
+	if (0 != control_packet_size) {
+		u8 control_type;
+		u8 *control_packet_data;
+		u8 *response_packet_data;
+		u32 version_length = sizeof(utgard_setup_version) - 1;
+
+		control_packet_data = (u8 *)(uintptr_t)args->control_packet_data;
+		MALI_DEBUG_ASSERT_POINTER(control_packet_data);
+		response_packet_data = (u8 *)(uintptr_t)args->response_packet_data;
+		MALI_DEBUG_ASSERT_POINTER(response_packet_data);
+
+		/*Decide if need to ignore Utgard setup version.*/
+		if (control_packet_size >= version_length) {
+			if (0 == memcmp(control_packet_data, utgard_setup_version, version_length)) {
+				if (control_packet_size == version_length) {
+					args->response_packet_size = 0;
+					return _MALI_OSK_ERR_OK;
+				} else {
+					control_packet_data += version_length;
+					control_packet_size -= version_length;
+				}
+			}
+		}
+
+		current_profiling_pid = _mali_osk_get_pid();
+
+		control_type = control_packet_data[0];
+		switch (control_type) {
+		case PACKET_HEADER_COUNTERS_REQUEST: {
+			int i;
+
+			if (PACKET_HEADER_SIZE > control_packet_size ||
+			    control_packet_size !=  _mali_profiling_get_packet_size(control_packet_data + 1)) {
+				MALI_PRINT_ERROR(("Wrong control packet  size, type 0x%x,size 0x%x.\n", control_packet_data[0], control_packet_size));
+				return _MALI_OSK_ERR_FAULT;
+			}
+
+			/* Send supported counters */
+			if (PACKET_HEADER_SIZE > output_buffer_size)
+				return _MALI_OSK_ERR_FAULT;
+
+			*response_packet_data = PACKET_HEADER_COUNTERS_ACK;
+			args->response_packet_size = PACKET_HEADER_SIZE;
+
+			for (i = 0; i < num_global_mali_profiling_counters; ++i) {
+				u32 name_size = strlen(global_mali_profiling_counters[i].counter_name);
+
+				if ((args->response_packet_size + name_size + 1) > output_buffer_size) {
+					MALI_PRINT_ERROR(("Response packet data is too large..\n"));
+					return _MALI_OSK_ERR_FAULT;
+				}
+
+				memcpy(response_packet_data + args->response_packet_size,
+				       global_mali_profiling_counters[i].counter_name, name_size + 1);
+
+				args->response_packet_size += (name_size + 1);
+
+				if (global_mali_profiling_counters[i].counter_id == COUNTER_VP_ACTIVITY) {
+					args->response_packet_size += _mali_profiling_pack_int(response_packet_data,
+								      output_buffer_size, args->response_packet_size, (s32)1);
+				} else if (global_mali_profiling_counters[i].counter_id == COUNTER_FP_ACTIVITY) {
+					args->response_packet_size += _mali_profiling_pack_int(response_packet_data,
+								      output_buffer_size, args->response_packet_size, (s32)mali_pp_get_glob_num_pp_cores());
+				} else {
+					args->response_packet_size += _mali_profiling_pack_int(response_packet_data,
+								      output_buffer_size, args->response_packet_size, (s32) - 1);
+				}
+			}
+
+			_mali_profiling_set_packet_size(response_packet_data + 1, args->response_packet_size);
+			break;
+		}
+
+		case PACKET_HEADER_COUNTERS_ENABLE: {
+			int i;
+			u32 request_pos = PACKET_HEADER_SIZE;
+			mali_bool sw_counter_if_enabled = MALI_FALSE;
+
+			if (PACKET_HEADER_SIZE > control_packet_size ||
+			    control_packet_size !=  _mali_profiling_get_packet_size(control_packet_data + 1)) {
+				MALI_PRINT_ERROR(("Wrong control packet  size , type 0x%x,size 0x%x.\n", control_packet_data[0], control_packet_size));
+				return _MALI_OSK_ERR_FAULT;
+			}
+
+			/* Init all counter states before enable requested counters.*/
+			for (i = 0; i < num_global_mali_profiling_counters; ++i) {
+				_mali_profiling_set_event(global_mali_profiling_counters[i].counter_id, MALI_HW_CORE_NO_COUNTER);
+				global_mali_profiling_counters[i].enabled = 0;
+				global_mali_profiling_counters[i].prev_counter_value = 0;
+				global_mali_profiling_counters[i].current_counter_value = 0;
+
+				if (global_mali_profiling_counters[i].counter_id >= FIRST_MEM_COUNTER &&
+				    global_mali_profiling_counters[i].counter_id <= LAST_MEM_COUNTER) {
+					_mali_profiling_notification_mem_counter(session, global_mali_profiling_counters[i].counter_id, 0, 0);
+				}
+			}
+
+			l2_cache_counter_if_enabled = MALI_FALSE;
+			num_counters_enabled = 0;
+			mem_counters_enabled = 0;
+			_mali_profiling_control(FBDUMP_CONTROL_ENABLE, 0);
+			_mali_profiling_control(SW_COUNTER_ENABLE, 0);
+			_mali_profiling_notification_enable(session, 0, 0);
+
+			/* Enable requested counters */
+			while (request_pos < control_packet_size) {
+				u32 begin = request_pos;
+				u32 event;
+				u32 key;
+
+				/* Check the counter name which should be ended with null */
+				while (request_pos < control_packet_size && control_packet_data[request_pos] != '\0') {
+					++request_pos;
+				}
+
+				if (request_pos >= control_packet_size)
+					return _MALI_OSK_ERR_FAULT;
+
+				++request_pos;
+				event = _mali_profiling_read_packet_int(control_packet_data, &request_pos, control_packet_size);
+				key = _mali_profiling_read_packet_int(control_packet_data, &request_pos, control_packet_size);
+
+				for (i = 0; i < num_global_mali_profiling_counters; ++i) {
+					u32 name_size = strlen((char *)(control_packet_data + begin));
+
+					if (strncmp(global_mali_profiling_counters[i].counter_name, (char *)(control_packet_data + begin), name_size) == 0) {
+						if (!sw_counter_if_enabled && (FIRST_SW_COUNTER <= global_mali_profiling_counters[i].counter_id
+									       && global_mali_profiling_counters[i].counter_id <= LAST_SW_COUNTER)) {
+							sw_counter_if_enabled = MALI_TRUE;
+							_mali_profiling_control(SW_COUNTER_ENABLE, 1);
+						}
+
+						if (COUNTER_FILMSTRIP == global_mali_profiling_counters[i].counter_id) {
+							_mali_profiling_control(FBDUMP_CONTROL_ENABLE, 1);
+							_mali_profiling_control(FBDUMP_CONTROL_RATE, event & 0xff);
+							_mali_profiling_control(FBDUMP_CONTROL_RESIZE_FACTOR, (event >> 8) & 0xff);
+						}
+
+						if (global_mali_profiling_counters[i].counter_id >= FIRST_MEM_COUNTER &&
+						    global_mali_profiling_counters[i].counter_id <= LAST_MEM_COUNTER) {
+							_mali_profiling_notification_mem_counter(session, global_mali_profiling_counters[i].counter_id,
+									key, 1);
+							mem_counters_enabled++;
+						}
+
+						global_mali_profiling_counters[i].counter_event = event;
+						global_mali_profiling_counters[i].key = key;
+						global_mali_profiling_counters[i].enabled = 1;
+
+						_mali_profiling_set_event(global_mali_profiling_counters[i].counter_id,
+									  global_mali_profiling_counters[i].counter_event);
+						num_counters_enabled++;
+						break;
+					}
+				}
+
+				if (i == num_global_mali_profiling_counters) {
+					MALI_PRINT_ERROR(("Counter name does not match for type %u.\n", control_type));
+					return _MALI_OSK_ERR_FAULT;
+				}
+			}
+
+			if (PACKET_HEADER_SIZE <= output_buffer_size) {
+				*response_packet_data = PACKET_HEADER_ACK;
+				_mali_profiling_set_packet_size(response_packet_data + 1, PACKET_HEADER_SIZE);
+				args->response_packet_size = PACKET_HEADER_SIZE;
+			} else {
+				return _MALI_OSK_ERR_FAULT;
+			}
+
+			break;
+		}
+
+		case PACKET_HEADER_START_CAPTURE_VALUE: {
+			u32 live_rate;
+			u32 request_pos = PACKET_HEADER_SIZE;
+
+			if (PACKET_HEADER_SIZE > control_packet_size ||
+			    control_packet_size !=  _mali_profiling_get_packet_size(control_packet_data + 1)) {
+				MALI_PRINT_ERROR(("Wrong control packet  size , type 0x%x,size 0x%x.\n", control_packet_data[0], control_packet_size));
+				return _MALI_OSK_ERR_FAULT;
+			}
+
+			/* Read samping rate in nanoseconds and live rate, start capture.*/
+			profiling_sample_rate =  _mali_profiling_read_packet_int(control_packet_data,
+						 &request_pos, control_packet_size);
+
+			live_rate = _mali_profiling_read_packet_int(control_packet_data, &request_pos, control_packet_size);
+
+			if (PACKET_HEADER_SIZE <= output_buffer_size) {
+				*response_packet_data = PACKET_HEADER_ACK;
+				_mali_profiling_set_packet_size(response_packet_data + 1, PACKET_HEADER_SIZE);
+				args->response_packet_size = PACKET_HEADER_SIZE;
+			} else {
+				return _MALI_OSK_ERR_FAULT;
+			}
+
+			if (0 != num_counters_enabled && 0 != profiling_sample_rate) {
+				_mali_profiling_global_stream_list_free();
+				if (mem_counters_enabled > 0) {
+					_mali_profiling_notification_enable(session, profiling_sample_rate, 1);
+				}
+				hrtimer_start(&profiling_sampling_timer,
+					      ktime_set(profiling_sample_rate / 1000000000, profiling_sample_rate % 1000000000),
+					      HRTIMER_MODE_REL_PINNED);
+			}
+
+			break;
+		}
+		default:
+			MALI_PRINT_ERROR(("Unsupported  profiling packet header type %u.\n", control_type));
+			args->response_packet_size  = 0;
+			return _MALI_OSK_ERR_FAULT;
+		}
+	} else {
+		_mali_osk_profiling_stop_sampling(current_profiling_pid);
+		_mali_profiling_notification_enable(session, 0, 0);
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+/**
+ * Called by gator.ko to set HW counters
+ *
+ * @param counter_id The counter ID.
+ * @param event_id Event ID that the counter should count (HW counter value from TRM).
+ *
+ * @return 1 on success, 0 on failure.
+ */
+int _mali_profiling_set_event(u32 counter_id, s32 event_id)
+{
+	if (COUNTER_VP_0_C0 == counter_id) {
+		mali_gp_job_set_gp_counter_src0(event_id);
+	} else if (COUNTER_VP_0_C1 == counter_id) {
+		mali_gp_job_set_gp_counter_src1(event_id);
+	} else if (COUNTER_FP_0_C0 <= counter_id && COUNTER_FP_7_C1 >= counter_id) {
+		/*
+		 * Two compatibility notes for this function:
+		 *
+		 * 1) Previously the DDK allowed per core counters.
+		 *
+		 *    This did not make much sense on Mali-450 with the "virtual PP core" concept,
+		 *    so this option was removed, and only the same pair of HW counters was allowed on all cores,
+		 *    beginning with r3p2 release.
+		 *
+		 *    Starting with r4p0, it is now possible to set different HW counters for the different sub jobs.
+		 *    This should be almost the same, since sub job 0 is designed to run on core 0,
+		 *    sub job 1 on core 1, and so on.
+		 *
+		 *    The scheduling of PP sub jobs is not predictable, and this often led to situations where core 0 ran 2
+		 *    sub jobs, while for instance core 1 ran zero. Having the counters set per sub job would thus increase
+		 *    the predictability of the returned data (as you would be guaranteed data for all the selected HW counters).
+		 *
+		 *    PS: Core scaling needs to be disabled in order to use this reliably (goes for both solutions).
+		 *
+		 *    The framework/#defines with Gator still indicates that the counter is for a particular core,
+		 *    but this is internally used as a sub job ID instead (no translation needed).
+		 *
+		 *  2) Global/default vs per sub job counters
+		 *
+		 *     Releases before r3p2 had only per PP core counters.
+		 *     r3p2 releases had only one set of default/global counters which applied to all PP cores
+		 *     Starting with r4p0, we have both a set of default/global counters,
+		 *     and individual counters per sub job (equal to per core).
+		 *
+		 *     To keep compatibility with Gator/DS-5/streamline, the following scheme is used:
+		 *
+		 *     r3p2 release; only counters set for core 0 is handled,
+		 *     this is applied as the default/global set of counters, and will thus affect all cores.
+		 *
+		 *     r4p0 release; counters set for core 0 is applied as both the global/default set of counters,
+		 *     and counters for sub job 0.
+		 *     Counters set for core 1-7 is only applied for the corresponding sub job.
+		 *
+		 *     This should allow the DS-5/Streamline GUI to have a simple mode where it only allows setting the
+		 *     values for core 0, and thus this will be applied to all PP sub jobs/cores.
+		 *     Advanced mode will also be supported, where individual pairs of HW counters can be selected.
+		 *
+		 *     The GUI will (until it is updated) still refer to cores instead of sub jobs, but this is probably
+		 *     something we can live with!
+		 *
+		 *     Mali-450 note: Each job is not divided into a deterministic number of sub jobs, as the HW DLBU
+		 *     automatically distributes the load between whatever number of cores is available at this particular time.
+		 *     A normal PP job on Mali-450 is thus considered a single (virtual) job, and it will thus only be possible
+		 *     to use a single pair of HW counters (even if the job ran on multiple PP cores).
+		 *     In other words, only the global/default pair of PP HW counters will be used for normal Mali-450 jobs.
+		 */
+		u32 sub_job = (counter_id - COUNTER_FP_0_C0) >> 1;
+		u32 counter_src = (counter_id - COUNTER_FP_0_C0) & 1;
+		if (0 == counter_src) {
+			mali_pp_job_set_pp_counter_sub_job_src0(sub_job, event_id);
+			if (0 == sub_job) {
+				mali_pp_job_set_pp_counter_global_src0(event_id);
+			}
+		} else {
+			mali_pp_job_set_pp_counter_sub_job_src1(sub_job, event_id);
+			if (0 == sub_job) {
+				mali_pp_job_set_pp_counter_global_src1(event_id);
+			}
+		}
+	} else if (COUNTER_L2_0_C0 <= counter_id && COUNTER_L2_2_C1 >= counter_id) {
+		u32 core_id = (counter_id - COUNTER_L2_0_C0) >> 1;
+		struct mali_l2_cache_core *l2_cache_core = mali_l2_cache_core_get_glob_l2_core(core_id);
+
+		if (NULL != l2_cache_core) {
+			u32 counter_src = (counter_id - COUNTER_L2_0_C0) & 1;
+			mali_l2_cache_core_set_counter_src(l2_cache_core,
+							   counter_src, event_id);
+			l2_cache_counter_if_enabled = MALI_TRUE;
+		}
+	} else {
+		return 0; /* Failure, unknown event */
+	}
+
+	return 1; /* success */
+}
+
+/**
+ * Called by gator.ko to retrieve the L2 cache counter values for all L2 cache cores.
+ * The L2 cache counters are unique in that they are polled by gator, rather than being
+ * transmitted via the tracepoint mechanism.
+ *
+ * @param values Pointer to a _mali_profiling_l2_counter_values structure where
+ *               the counter sources and values will be output
+ * @return 0 if all went well; otherwise, return the mask with the bits set for the powered off cores
+ */
+u32 _mali_profiling_get_l2_counters(_mali_profiling_l2_counter_values *values)
+{
+	u32 l2_cores_num = mali_l2_cache_core_get_glob_num_l2_cores();
+	u32 i;
+
+	MALI_DEBUG_ASSERT(l2_cores_num <= 3);
+
+	for (i = 0; i < l2_cores_num; i++) {
+		struct mali_l2_cache_core *l2_cache = mali_l2_cache_core_get_glob_l2_core(i);
+
+		if (NULL == l2_cache) {
+			continue;
+		}
+
+		mali_l2_cache_core_get_counter_values(l2_cache,
+						      &values->cores[i].source0,
+						      &values->cores[i].value0,
+						      &values->cores[i].source1,
+						      &values->cores[i].value1);
+	}
+
+	return 0;
+}
+
+/**
+ * Called by gator to control the production of profiling information at runtime.
+ */
+void _mali_profiling_control(u32 action, u32 value)
+{
+	switch (action) {
+	case FBDUMP_CONTROL_ENABLE:
+		mali_set_user_setting(_MALI_UK_USER_SETTING_COLORBUFFER_CAPTURE_ENABLED, (value == 0 ? MALI_FALSE : MALI_TRUE));
+		break;
+	case FBDUMP_CONTROL_RATE:
+		mali_set_user_setting(_MALI_UK_USER_SETTING_BUFFER_CAPTURE_N_FRAMES, value);
+		break;
+	case SW_COUNTER_ENABLE:
+		mali_set_user_setting(_MALI_UK_USER_SETTING_SW_COUNTER_ENABLED, value);
+		break;
+	case FBDUMP_CONTROL_RESIZE_FACTOR:
+		mali_set_user_setting(_MALI_UK_USER_SETTING_BUFFER_CAPTURE_RESIZE_FACTOR, value);
+		break;
+	default:
+		break;  /* Ignore unimplemented actions */
+	}
+}
+
+/**
+ * Called by gator to get mali api version.
+ */
+u32 _mali_profiling_get_api_version(void)
+{
+	return MALI_PROFILING_API_VERSION;
+}
+
+/**
+* Called by gator to get the data about Mali instance in use:
+* product id, version, number of cores
+*/
+void _mali_profiling_get_mali_version(struct _mali_profiling_mali_version *values)
+{
+	values->mali_product_id = (u32)mali_kernel_core_get_product_id();
+	values->mali_version_major = mali_kernel_core_get_gpu_major_version();
+	values->mali_version_minor = mali_kernel_core_get_gpu_minor_version();
+	values->num_of_l2_cores = mali_l2_cache_core_get_glob_num_l2_cores();
+	values->num_of_fp_cores = mali_executor_get_num_cores_total();
+	values->num_of_vp_cores = 1;
+}
+
+
+EXPORT_SYMBOL(_mali_profiling_set_event);
+EXPORT_SYMBOL(_mali_profiling_get_l2_counters);
+EXPORT_SYMBOL(_mali_profiling_control);
+EXPORT_SYMBOL(_mali_profiling_get_api_version);
+EXPORT_SYMBOL(_mali_profiling_get_mali_version);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_specific.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_specific.h
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2010, 2012-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_specific.h
+ * Defines per-OS Kernel level specifics, such as unusual workarounds for
+ * certain OSs.
+ */
+
+#ifndef __MALI_OSK_SPECIFIC_H__
+#define __MALI_OSK_SPECIFIC_H__
+
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+#include <linux/platform_device.h>
+#include <linux/gfp.h>
+#include <linux/hardirq.h>
+
+
+#include "mali_osk_types.h"
+#include "mali_kernel_linux.h"
+
+#define MALI_STATIC_INLINE static inline
+#define MALI_NON_STATIC_INLINE inline
+
+typedef struct dma_pool *mali_dma_pool;
+
+typedef u32 mali_dma_addr;
+
+#if MALI_ENABLE_CPU_CYCLES
+/* Reads out the clock cycle performance counter of the current cpu.
+   It is useful for cost-free (2 cycle) measuring of the time spent
+   in a code path. Sample before and after, the diff number of cycles.
+   When the CPU is idle it will not increase this clock counter.
+   It means that the counter is accurate if only spin-locks are used,
+   but mutexes may lead to too low values since the cpu might "idle"
+   waiting for the mutex to become available.
+   The clock source is configured on the CPU during mali module load,
+   but will not give useful output after a CPU has been power cycled.
+   It is therefore important to configure the system to not turn of
+   the cpu cores when using this functionallity.*/
+static inline unsigned int mali_get_cpu_cyclecount(void)
+{
+	unsigned int value;
+	/* Reading the CCNT Register - CPU clock counter */
+	asm volatile("MRC p15, 0, %0, c9, c13, 0\t\n": "=r"(value));
+	return value;
+}
+
+void mali_init_cpu_time_counters(int reset, int enable_divide_by_64);
+#endif
+
+
+MALI_STATIC_INLINE u32 _mali_osk_copy_from_user(void *to, void *from, u32 n)
+{
+	return (u32)copy_from_user(to, from, (unsigned long)n);
+}
+
+MALI_STATIC_INLINE mali_bool _mali_osk_in_atomic(void)
+{
+	return in_atomic();
+}
+
+#define _mali_osk_put_user(x, ptr) put_user(x, ptr)
+
+#endif /* __MALI_OSK_SPECIFIC_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_time.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_time.c
@@ -0,0 +1,71 @@
+/*
+ * Copyright (C) 2010, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_time.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include "mali_osk.h"
+#include <linux/jiffies.h>
+#include <linux/time.h>
+#include <asm/delay.h>
+
+mali_bool _mali_osk_time_after_eq(unsigned long ticka, unsigned long tickb)
+{
+	return time_after_eq(ticka, tickb) ?
+	       MALI_TRUE : MALI_FALSE;
+}
+
+unsigned long _mali_osk_time_mstoticks(u32 ms)
+{
+	return msecs_to_jiffies(ms);
+}
+
+u32 _mali_osk_time_tickstoms(unsigned long ticks)
+{
+	return jiffies_to_msecs(ticks);
+}
+
+unsigned long _mali_osk_time_tickcount(void)
+{
+	return jiffies;
+}
+
+void _mali_osk_time_ubusydelay(u32 usecs)
+{
+	udelay(usecs);
+}
+
+u64 _mali_osk_time_get_ns(void)
+{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+	struct timespec64 tsval;
+	ktime_get_real_ts64(&tsval);
+	return (u64)timespec64_to_ns(&tsval);
+#else
+	struct timespec tsval;
+	getnstimeofday(&tsval);
+	return (u64)timespec_to_ns(&tsval);
+#endif
+}
+
+u64 _mali_osk_boot_time_get_ns(void)
+{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 20, 0)
+	struct timespec64 tsval;
+	ktime_get_boottime_ts64(&tsval);
+	return (u64)timespec64_to_ns(&tsval);
+#else
+	struct timespec tsval;
+	get_monotonic_boottime(&tsval);
+	return (u64)timespec_to_ns(&tsval);
+#endif
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_timers.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_timers.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_timers.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include <linux/timer.h>
+#include <linux/slab.h>
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+struct _mali_osk_timer_t_struct {
+	struct timer_list timer;
+};
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+typedef void (*timer_timeout_function_t)(struct timer_list *);
+#else
+typedef void (*timer_timeout_function_t)(unsigned long);
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+_mali_osk_timer_t *_mali_osk_timer_init(_mali_osk_timer_callback_t callback)
+#else
+_mali_osk_timer_t *_mali_osk_timer_init(void)
+#endif
+{
+	_mali_osk_timer_t *t = (_mali_osk_timer_t *)kmalloc(sizeof(_mali_osk_timer_t), GFP_KERNEL);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 14, 0)
+	if (NULL != t) timer_setup(&t->timer, (timer_timeout_function_t)callback, 0);
+#else
+	if (NULL != t) init_timer(&t->timer);
+#endif
+	return t;
+}
+
+void _mali_osk_timer_add(_mali_osk_timer_t *tim, unsigned long ticks_to_expire)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	tim->timer.expires = jiffies + ticks_to_expire;
+	add_timer(&(tim->timer));
+}
+
+void _mali_osk_timer_mod(_mali_osk_timer_t *tim, unsigned long ticks_to_expire)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	mod_timer(&(tim->timer), jiffies + ticks_to_expire);
+}
+
+void _mali_osk_timer_del(_mali_osk_timer_t *tim)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	del_timer_sync(&(tim->timer));
+}
+
+void _mali_osk_timer_del_async(_mali_osk_timer_t *tim)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	del_timer(&(tim->timer));
+}
+
+mali_bool _mali_osk_timer_pending(_mali_osk_timer_t *tim)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	return 1 == timer_pending(&(tim->timer));
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 14, 0)
+void _mali_osk_timer_setcallback(_mali_osk_timer_t *tim, _mali_osk_timer_callback_t callback, void *data)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	tim->timer.data = (unsigned long)data;
+	tim->timer.function = (timer_timeout_function_t)callback;
+}
+#endif
+
+void _mali_osk_timer_term(_mali_osk_timer_t *tim)
+{
+	MALI_DEBUG_ASSERT_POINTER(tim);
+	kfree(tim);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_wait_queue.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_wait_queue.c
@@ -0,0 +1,78 @@
+/*
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_wait_queue.c
+ * Implemenation of the OS abstraction layer for the kernel device driver
+ */
+
+#include <linux/wait.h>
+#include <linux/slab.h>
+#include <linux/sched.h>
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+
+struct _mali_osk_wait_queue_t_struct {
+	wait_queue_head_t wait_queue;
+};
+
+_mali_osk_wait_queue_t *_mali_osk_wait_queue_init(void)
+{
+	_mali_osk_wait_queue_t *ret = NULL;
+
+	ret = kmalloc(sizeof(_mali_osk_wait_queue_t), GFP_KERNEL);
+
+	if (NULL == ret) {
+		return ret;
+	}
+
+	init_waitqueue_head(&ret->wait_queue);
+	MALI_DEBUG_ASSERT(!waitqueue_active(&ret->wait_queue));
+
+	return ret;
+}
+
+void _mali_osk_wait_queue_wait_event(_mali_osk_wait_queue_t *queue, mali_bool(*condition)(void *), void *data)
+{
+	MALI_DEBUG_ASSERT_POINTER(queue);
+	MALI_DEBUG_PRINT(6, ("Adding to wait queue %p\n", queue));
+	wait_event(queue->wait_queue, condition(data));
+}
+
+void _mali_osk_wait_queue_wait_event_timeout(_mali_osk_wait_queue_t *queue, mali_bool(*condition)(void *), void *data, u32 timeout)
+{
+	MALI_DEBUG_ASSERT_POINTER(queue);
+	MALI_DEBUG_PRINT(6, ("Adding to wait queue %p\n", queue));
+	wait_event_timeout(queue->wait_queue, condition(data), _mali_osk_time_mstoticks(timeout));
+}
+
+void _mali_osk_wait_queue_wake_up(_mali_osk_wait_queue_t *queue)
+{
+	MALI_DEBUG_ASSERT_POINTER(queue);
+
+	/* if queue is empty, don't attempt to wake up its elements */
+	if (!waitqueue_active(&queue->wait_queue)) return;
+
+	MALI_DEBUG_PRINT(6, ("Waking up elements in wait queue %p ....\n", queue));
+
+	wake_up_all(&queue->wait_queue);
+
+	MALI_DEBUG_PRINT(6, ("... elements in wait queue %p woken up\n", queue));
+}
+
+void _mali_osk_wait_queue_term(_mali_osk_wait_queue_t *queue)
+{
+	/* Parameter validation  */
+	MALI_DEBUG_ASSERT_POINTER(queue);
+
+	/* Linux requires no explicit termination of wait queues */
+	kfree(queue);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_osk_wq.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_osk_wq.c
@@ -0,0 +1,240 @@
+/*
+ * Copyright (C) 2010-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_osk_wq.c
+ * Implementation of the OS abstraction layer for the kernel device driver
+ */
+
+#include <linux/slab.h> /* For memory allocation */
+#include <linux/workqueue.h>
+#include <linux/version.h>
+#include <linux/sched.h>
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_kernel_license.h"
+#include "mali_kernel_linux.h"
+
+typedef struct _mali_osk_wq_work_s {
+	_mali_osk_wq_work_handler_t handler;
+	void *data;
+	mali_bool high_pri;
+	struct work_struct work_handle;
+} mali_osk_wq_work_object_t;
+
+typedef struct _mali_osk_wq_delayed_work_s {
+	_mali_osk_wq_work_handler_t handler;
+	void *data;
+	struct delayed_work work;
+} mali_osk_wq_delayed_work_object_t;
+
+#if MALI_LICENSE_IS_GPL
+static struct workqueue_struct *mali_wq_normal = NULL;
+static struct workqueue_struct *mali_wq_high = NULL;
+#endif
+
+static void _mali_osk_wq_work_func(struct work_struct *work);
+
+_mali_osk_errcode_t _mali_osk_wq_init(void)
+{
+#if MALI_LICENSE_IS_GPL
+	MALI_DEBUG_ASSERT(NULL == mali_wq_normal);
+	MALI_DEBUG_ASSERT(NULL == mali_wq_high);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 36)
+	mali_wq_normal = alloc_workqueue("mali", WQ_UNBOUND, 0);
+	mali_wq_high = alloc_workqueue("mali_high_pri", WQ_HIGHPRI | WQ_UNBOUND, 0);
+#else
+	mali_wq_normal = create_workqueue("mali");
+	mali_wq_high = create_workqueue("mali_high_pri");
+#endif
+	if (NULL == mali_wq_normal || NULL == mali_wq_high) {
+		MALI_PRINT_ERROR(("Unable to create Mali workqueues\n"));
+
+		if (mali_wq_normal) destroy_workqueue(mali_wq_normal);
+		if (mali_wq_high)   destroy_workqueue(mali_wq_high);
+
+		mali_wq_normal = NULL;
+		mali_wq_high   = NULL;
+
+		return _MALI_OSK_ERR_FAULT;
+	}
+#endif /* MALI_LICENSE_IS_GPL */
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void _mali_osk_wq_flush(void)
+{
+#if MALI_LICENSE_IS_GPL
+	flush_workqueue(mali_wq_high);
+	flush_workqueue(mali_wq_normal);
+#else
+	flush_scheduled_work();
+#endif
+}
+
+void _mali_osk_wq_term(void)
+{
+#if MALI_LICENSE_IS_GPL
+	MALI_DEBUG_ASSERT(NULL != mali_wq_normal);
+	MALI_DEBUG_ASSERT(NULL != mali_wq_high);
+
+	flush_workqueue(mali_wq_normal);
+	destroy_workqueue(mali_wq_normal);
+
+	flush_workqueue(mali_wq_high);
+	destroy_workqueue(mali_wq_high);
+
+	mali_wq_normal = NULL;
+	mali_wq_high   = NULL;
+#else
+	flush_scheduled_work();
+#endif
+}
+
+_mali_osk_wq_work_t *_mali_osk_wq_create_work(_mali_osk_wq_work_handler_t handler, void *data)
+{
+	mali_osk_wq_work_object_t *work = kmalloc(sizeof(mali_osk_wq_work_object_t), GFP_KERNEL);
+
+	if (NULL == work) return NULL;
+
+	work->handler = handler;
+	work->data = data;
+	work->high_pri = MALI_FALSE;
+
+	INIT_WORK(&work->work_handle, _mali_osk_wq_work_func);
+
+	return work;
+}
+
+_mali_osk_wq_work_t *_mali_osk_wq_create_work_high_pri(_mali_osk_wq_work_handler_t handler, void *data)
+{
+	mali_osk_wq_work_object_t *work = kmalloc(sizeof(mali_osk_wq_work_object_t), GFP_KERNEL);
+
+	if (NULL == work) return NULL;
+
+	work->handler = handler;
+	work->data = data;
+	work->high_pri = MALI_TRUE;
+
+	INIT_WORK(&work->work_handle, _mali_osk_wq_work_func);
+
+	return work;
+}
+
+void _mali_osk_wq_delete_work(_mali_osk_wq_work_t *work)
+{
+	mali_osk_wq_work_object_t *work_object = (mali_osk_wq_work_object_t *)work;
+	_mali_osk_wq_flush();
+	kfree(work_object);
+}
+
+void _mali_osk_wq_delete_work_nonflush(_mali_osk_wq_work_t *work)
+{
+	mali_osk_wq_work_object_t *work_object = (mali_osk_wq_work_object_t *)work;
+	kfree(work_object);
+}
+
+void _mali_osk_wq_schedule_work(_mali_osk_wq_work_t *work)
+{
+	mali_osk_wq_work_object_t *work_object = (mali_osk_wq_work_object_t *)work;
+#if MALI_LICENSE_IS_GPL
+	queue_work(mali_wq_normal, &work_object->work_handle);
+#else
+	schedule_work(&work_object->work_handle);
+#endif
+}
+
+void _mali_osk_wq_schedule_work_high_pri(_mali_osk_wq_work_t *work)
+{
+	mali_osk_wq_work_object_t *work_object = (mali_osk_wq_work_object_t *)work;
+#if MALI_LICENSE_IS_GPL
+	queue_work(mali_wq_high, &work_object->work_handle);
+#else
+	schedule_work(&work_object->work_handle);
+#endif
+}
+
+static void _mali_osk_wq_work_func(struct work_struct *work)
+{
+	mali_osk_wq_work_object_t *work_object;
+
+	work_object = _MALI_OSK_CONTAINER_OF(work, mali_osk_wq_work_object_t, work_handle);
+
+#if MALI_LICENSE_IS_GPL
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,36)
+	/* We want highest Dynamic priority of the thread so that the Jobs depending
+	** on this thread could be scheduled in time. Without this, this thread might
+	** sometimes need to wait for some threads in user mode to finish its round-robin
+	** time, causing *bubble* in the Mali pipeline. Thanks to the new implementation
+	** of high-priority workqueue in new kernel, this only happens in older kernel.
+	*/
+	if (MALI_TRUE == work_object->high_pri) {
+		set_user_nice(current, -19);
+	}
+#endif
+#endif /* MALI_LICENSE_IS_GPL */
+
+	work_object->handler(work_object->data);
+}
+
+static void _mali_osk_wq_delayed_work_func(struct work_struct *work)
+{
+	mali_osk_wq_delayed_work_object_t *work_object;
+
+	work_object = _MALI_OSK_CONTAINER_OF(work, mali_osk_wq_delayed_work_object_t, work.work);
+	work_object->handler(work_object->data);
+}
+
+mali_osk_wq_delayed_work_object_t *_mali_osk_wq_delayed_create_work(_mali_osk_wq_work_handler_t handler, void *data)
+{
+	mali_osk_wq_delayed_work_object_t *work = kmalloc(sizeof(mali_osk_wq_delayed_work_object_t), GFP_KERNEL);
+
+	if (NULL == work) return NULL;
+
+	work->handler = handler;
+	work->data = data;
+
+	INIT_DELAYED_WORK(&work->work, _mali_osk_wq_delayed_work_func);
+
+	return work;
+}
+
+void _mali_osk_wq_delayed_delete_work_nonflush(_mali_osk_wq_delayed_work_t *work)
+{
+	mali_osk_wq_delayed_work_object_t *work_object = (mali_osk_wq_delayed_work_object_t *)work;
+	kfree(work_object);
+}
+
+void _mali_osk_wq_delayed_cancel_work_async(_mali_osk_wq_delayed_work_t *work)
+{
+	mali_osk_wq_delayed_work_object_t *work_object = (mali_osk_wq_delayed_work_object_t *)work;
+	cancel_delayed_work(&work_object->work);
+}
+
+void _mali_osk_wq_delayed_cancel_work_sync(_mali_osk_wq_delayed_work_t *work)
+{
+	mali_osk_wq_delayed_work_object_t *work_object = (mali_osk_wq_delayed_work_object_t *)work;
+	cancel_delayed_work_sync(&work_object->work);
+}
+
+void _mali_osk_wq_delayed_schedule_work(_mali_osk_wq_delayed_work_t *work, u32 delay)
+{
+	mali_osk_wq_delayed_work_object_t *work_object = (mali_osk_wq_delayed_work_object_t *)work;
+
+#if MALI_LICENSE_IS_GPL
+	queue_delayed_work(mali_wq_normal, &work_object->work, delay);
+#else
+	schedule_delayed_work(&work_object->work, delay);
+#endif
+
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_pmu_power_up_down.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_pmu_power_up_down.c
@@ -0,0 +1,23 @@
+/**
+ * Copyright (C) 2010, 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_pmu_power_up_down.c
+ */
+
+#include <linux/module.h>
+#include "mali_executor.h"
+
+int mali_perf_set_num_pp_cores(unsigned int num_cores)
+{
+	return mali_executor_set_perf_level(num_cores, MALI_FALSE);
+}
+
+EXPORT_SYMBOL(mali_perf_set_num_pp_cores);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_profiling_events.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_profiling_events.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2012, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PROFILING_EVENTS_H__
+#define __MALI_PROFILING_EVENTS_H__
+
+/* Simple wrapper in order to find the OS specific location of this file */
+#include <linux/mali/mali_utgard_profiling_events.h>
+
+#endif /* __MALI_PROFILING_EVENTS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_profiling_gator_api.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_profiling_gator_api.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2012-2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PROFILING_GATOR_API_H__
+#define __MALI_PROFILING_GATOR_API_H__
+
+/* Simple wrapper in order to find the OS specific location of this file */
+#include <linux/mali/mali_utgard_profiling_gator_api.h>
+
+#endif /* __MALI_PROFILING_GATOR_API_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_profiling_internal.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_profiling_internal.c
@@ -0,0 +1,275 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_kernel_common.h"
+#include "mali_osk.h"
+#include "mali_osk_mali.h"
+#include "mali_ukk.h"
+#include "mali_timestamp.h"
+#include "mali_osk_profiling.h"
+#include "mali_user_settings_db.h"
+#include "mali_profiling_internal.h"
+
+typedef struct mali_profiling_entry {
+	u64 timestamp;
+	u32 event_id;
+	u32 data[5];
+} mali_profiling_entry;
+
+typedef enum mali_profiling_state {
+	MALI_PROFILING_STATE_UNINITIALIZED,
+	MALI_PROFILING_STATE_IDLE,
+	MALI_PROFILING_STATE_RUNNING,
+	MALI_PROFILING_STATE_RETURN,
+} mali_profiling_state;
+
+static _mali_osk_mutex_t *lock = NULL;
+static mali_profiling_state prof_state = MALI_PROFILING_STATE_UNINITIALIZED;
+static mali_profiling_entry *profile_entries = NULL;
+static _mali_osk_atomic_t profile_insert_index;
+static u32 profile_mask = 0;
+
+static inline void add_event(u32 event_id, u32 data0, u32 data1, u32 data2, u32 data3, u32 data4);
+
+void probe_mali_timeline_event(void *data, TP_PROTO(unsigned int event_id, unsigned int d0, unsigned int d1, unsigned
+			       int d2, unsigned int d3, unsigned int d4))
+{
+	add_event(event_id, d0, d1, d2, d3, d4);
+}
+
+_mali_osk_errcode_t _mali_internal_profiling_init(mali_bool auto_start)
+{
+	profile_entries = NULL;
+	profile_mask = 0;
+	_mali_osk_atomic_init(&profile_insert_index, 0);
+
+	lock = _mali_osk_mutex_init(_MALI_OSK_LOCKFLAG_ORDERED, _MALI_OSK_LOCK_ORDER_PROFILING);
+	if (NULL == lock) {
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	prof_state = MALI_PROFILING_STATE_IDLE;
+
+	if (MALI_TRUE == auto_start) {
+		u32 limit = MALI_PROFILING_MAX_BUFFER_ENTRIES; /* Use maximum buffer size */
+
+		mali_set_user_setting(_MALI_UK_USER_SETTING_SW_EVENTS_ENABLE, MALI_TRUE);
+		if (_MALI_OSK_ERR_OK != _mali_internal_profiling_start(&limit)) {
+			return _MALI_OSK_ERR_FAULT;
+		}
+	}
+
+	return _MALI_OSK_ERR_OK;
+}
+
+void _mali_internal_profiling_term(void)
+{
+	u32 count;
+
+	/* Ensure profiling is stopped */
+	_mali_internal_profiling_stop(&count);
+
+	prof_state = MALI_PROFILING_STATE_UNINITIALIZED;
+
+	if (NULL != profile_entries) {
+		_mali_osk_vfree(profile_entries);
+		profile_entries = NULL;
+	}
+
+	if (NULL != lock) {
+		_mali_osk_mutex_term(lock);
+		lock = NULL;
+	}
+}
+
+_mali_osk_errcode_t _mali_internal_profiling_start(u32 *limit)
+{
+	_mali_osk_errcode_t ret;
+	mali_profiling_entry *new_profile_entries;
+
+	_mali_osk_mutex_wait(lock);
+
+	if (MALI_PROFILING_STATE_RUNNING == prof_state) {
+		_mali_osk_mutex_signal(lock);
+		return _MALI_OSK_ERR_BUSY;
+	}
+
+	new_profile_entries = _mali_osk_valloc(*limit * sizeof(mali_profiling_entry));
+
+	if (NULL == new_profile_entries) {
+		_mali_osk_mutex_signal(lock);
+		_mali_osk_vfree(new_profile_entries);
+		return _MALI_OSK_ERR_NOMEM;
+	}
+
+	if (MALI_PROFILING_MAX_BUFFER_ENTRIES < *limit) {
+		*limit = MALI_PROFILING_MAX_BUFFER_ENTRIES;
+	}
+
+	profile_mask = 1;
+	while (profile_mask <= *limit) {
+		profile_mask <<= 1;
+	}
+	profile_mask >>= 1;
+
+	*limit = profile_mask;
+
+	profile_mask--; /* turns the power of two into a mask of one less */
+
+	if (MALI_PROFILING_STATE_IDLE != prof_state) {
+		_mali_osk_mutex_signal(lock);
+		_mali_osk_vfree(new_profile_entries);
+		return _MALI_OSK_ERR_INVALID_ARGS; /* invalid to call this function in this state */
+	}
+
+	profile_entries = new_profile_entries;
+
+	ret = _mali_timestamp_reset();
+
+	if (_MALI_OSK_ERR_OK == ret) {
+		prof_state = MALI_PROFILING_STATE_RUNNING;
+	} else {
+		_mali_osk_vfree(profile_entries);
+		profile_entries = NULL;
+	}
+
+	register_trace_mali_timeline_event(probe_mali_timeline_event, NULL);
+
+	_mali_osk_mutex_signal(lock);
+	return ret;
+}
+
+static inline void add_event(u32 event_id, u32 data0, u32 data1, u32 data2, u32 data3, u32 data4)
+{
+	u32 cur_index = (_mali_osk_atomic_inc_return(&profile_insert_index) - 1) & profile_mask;
+
+	profile_entries[cur_index].timestamp = _mali_timestamp_get();
+	profile_entries[cur_index].event_id = event_id;
+	profile_entries[cur_index].data[0] = data0;
+	profile_entries[cur_index].data[1] = data1;
+	profile_entries[cur_index].data[2] = data2;
+	profile_entries[cur_index].data[3] = data3;
+	profile_entries[cur_index].data[4] = data4;
+
+	/* If event is "leave API function", add current memory usage to the event
+	 * as data point 4.  This is used in timeline profiling to indicate how
+	 * much memory was used when leaving a function. */
+	if (event_id == (MALI_PROFILING_EVENT_TYPE_SINGLE | MALI_PROFILING_EVENT_CHANNEL_SOFTWARE | MALI_PROFILING_EVENT_REASON_SINGLE_SW_LEAVE_API_FUNC)) {
+		profile_entries[cur_index].data[4] = _mali_ukk_report_memory_usage();
+	}
+}
+
+_mali_osk_errcode_t _mali_internal_profiling_stop(u32 *count)
+{
+	_mali_osk_mutex_wait(lock);
+
+	if (MALI_PROFILING_STATE_RUNNING != prof_state) {
+		_mali_osk_mutex_signal(lock);
+		return _MALI_OSK_ERR_INVALID_ARGS; /* invalid to call this function in this state */
+	}
+
+	/* go into return state (user to retreive events), no more events will be added after this */
+	prof_state = MALI_PROFILING_STATE_RETURN;
+
+	unregister_trace_mali_timeline_event(probe_mali_timeline_event, NULL);
+
+	_mali_osk_mutex_signal(lock);
+
+	tracepoint_synchronize_unregister();
+
+	*count = _mali_osk_atomic_read(&profile_insert_index);
+	if (*count > profile_mask) *count = profile_mask;
+
+	return _MALI_OSK_ERR_OK;
+}
+
+u32 _mali_internal_profiling_get_count(void)
+{
+	u32 retval = 0;
+
+	_mali_osk_mutex_wait(lock);
+	if (MALI_PROFILING_STATE_RETURN == prof_state) {
+		retval = _mali_osk_atomic_read(&profile_insert_index);
+		if (retval > profile_mask) retval = profile_mask;
+	}
+	_mali_osk_mutex_signal(lock);
+
+	return retval;
+}
+
+_mali_osk_errcode_t _mali_internal_profiling_get_event(u32 index, u64 *timestamp, u32 *event_id, u32 data[5])
+{
+	u32 raw_index = _mali_osk_atomic_read(&profile_insert_index);
+
+	_mali_osk_mutex_wait(lock);
+
+	if (index < profile_mask) {
+		if ((raw_index & ~profile_mask) != 0) {
+			index += raw_index;
+			index &= profile_mask;
+		}
+
+		if (prof_state != MALI_PROFILING_STATE_RETURN) {
+			_mali_osk_mutex_signal(lock);
+			return _MALI_OSK_ERR_INVALID_ARGS; /* invalid to call this function in this state */
+		}
+
+		if (index >= raw_index) {
+			_mali_osk_mutex_signal(lock);
+			return _MALI_OSK_ERR_FAULT;
+		}
+
+		*timestamp = profile_entries[index].timestamp;
+		*event_id = profile_entries[index].event_id;
+		data[0] = profile_entries[index].data[0];
+		data[1] = profile_entries[index].data[1];
+		data[2] = profile_entries[index].data[2];
+		data[3] = profile_entries[index].data[3];
+		data[4] = profile_entries[index].data[4];
+	} else {
+		_mali_osk_mutex_signal(lock);
+		return _MALI_OSK_ERR_FAULT;
+	}
+
+	_mali_osk_mutex_signal(lock);
+	return _MALI_OSK_ERR_OK;
+}
+
+_mali_osk_errcode_t _mali_internal_profiling_clear(void)
+{
+	_mali_osk_mutex_wait(lock);
+
+	if (MALI_PROFILING_STATE_RETURN != prof_state) {
+		_mali_osk_mutex_signal(lock);
+		return _MALI_OSK_ERR_INVALID_ARGS; /* invalid to call this function in this state */
+	}
+
+	prof_state = MALI_PROFILING_STATE_IDLE;
+	profile_mask = 0;
+	_mali_osk_atomic_init(&profile_insert_index, 0);
+
+	if (NULL != profile_entries) {
+		_mali_osk_vfree(profile_entries);
+		profile_entries = NULL;
+	}
+
+	_mali_osk_mutex_signal(lock);
+	return _MALI_OSK_ERR_OK;
+}
+
+mali_bool _mali_internal_profiling_is_recording(void)
+{
+	return prof_state == MALI_PROFILING_STATE_RUNNING ? MALI_TRUE : MALI_FALSE;
+}
+
+mali_bool _mali_internal_profiling_have_recording(void)
+{
+	return prof_state == MALI_PROFILING_STATE_RETURN ? MALI_TRUE : MALI_FALSE;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_profiling_internal.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_profiling_internal.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2012-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_PROFILING_INTERNAL_H__
+#define __MALI_PROFILING_INTERNAL_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "mali_osk.h"
+
+int _mali_internal_profiling_init(mali_bool auto_start);
+void _mali_internal_profiling_term(void);
+
+mali_bool _mali_internal_profiling_is_recording(void);
+mali_bool _mali_internal_profiling_have_recording(void);
+_mali_osk_errcode_t _mali_internal_profiling_clear(void);
+_mali_osk_errcode_t _mali_internal_profiling_get_event(u32 index, u64 *timestamp, u32 *event_id, u32 data[5]);
+u32 _mali_internal_profiling_get_count(void);
+int _mali_internal_profiling_stop(u32 *count);
+int _mali_internal_profiling_start(u32 *limit);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_PROFILING_INTERNAL_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_sync.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_sync.c
@@ -0,0 +1,669 @@
+/*
+ * Copyright (C) 2012-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_sync.h"
+
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_timeline.h"
+#include "mali_executor.h"
+
+#include <linux/file.h>
+#include <linux/seq_file.h>
+#include <linux/module.h>
+
+struct mali_sync_pt {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_pt         sync_pt;
+#else
+	struct mali_internal_sync_point         sync_pt;
+#endif
+	struct mali_sync_flag *flag;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_timeline *sync_tl;  /**< Sync timeline this pt is connected to. */
+#else
+	struct mali_internal_sync_timeline *sync_tl;  /**< Sync timeline this pt is connected to. */
+#endif
+};
+
+/**
+ * The sync flag is used to connect sync fences to the Mali Timeline system.  Sync fences can be
+ * created from a sync flag, and when the flag is signaled, the sync fences will also be signaled.
+ */
+struct mali_sync_flag {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_timeline *sync_tl;  /**< Sync timeline this flag is connected to. */
+#else
+	struct mali_internal_sync_timeline *sync_tl;  /**< Sync timeline this flag is connected to. */
+#endif
+	u32                   point;    /**< Point on timeline. */
+	int                   status;   /**< 0 if unsignaled, 1 if signaled without error or negative if signaled with error. */
+	struct kref           refcount; /**< Reference count. */
+};
+
+/**
+ * Mali sync timeline is used to connect mali timeline to sync_timeline.
+ * When fence timeout can print more detailed mali timeline system info.
+ */
+struct mali_sync_timeline_container {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	struct sync_timeline sync_timeline;
+#else
+	struct mali_internal_sync_timeline sync_timeline;
+#endif
+	struct mali_timeline *timeline;
+};
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+MALI_STATIC_INLINE struct mali_sync_pt *to_mali_sync_pt(struct sync_pt *pt)
+#else
+MALI_STATIC_INLINE struct mali_sync_pt *to_mali_sync_pt(struct mali_internal_sync_point *pt)
+#endif
+{
+	return container_of(pt, struct mali_sync_pt, sync_pt);
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+MALI_STATIC_INLINE struct mali_sync_timeline_container *to_mali_sync_tl_container(struct sync_timeline *sync_tl)
+#else
+MALI_STATIC_INLINE struct mali_sync_timeline_container *to_mali_sync_tl_container(struct mali_internal_sync_timeline *sync_tl)
+#endif
+{
+	return container_of(sync_tl, struct mali_sync_timeline_container, sync_timeline);
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static int timeline_has_signaled(struct sync_pt *pt)
+#else
+static int timeline_has_signaled(struct mali_internal_sync_point *pt)
+#endif
+{
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(pt);
+	mpt = to_mali_sync_pt(pt);
+
+	MALI_DEBUG_ASSERT_POINTER(mpt->flag);
+
+	return mpt->flag->status;
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static void timeline_free_pt(struct sync_pt *pt)
+#else
+static void timeline_free_pt(struct mali_internal_sync_point *pt)
+#endif
+{
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(pt);
+	mpt = to_mali_sync_pt(pt);
+
+	mali_sync_flag_put(mpt->flag);
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static void timeline_release(struct sync_timeline *sync_timeline)
+#else
+static void timeline_release(struct mali_internal_sync_timeline *sync_timeline)
+#endif
+{
+	struct mali_sync_timeline_container *mali_sync_tl = NULL;
+	struct mali_timeline *mali_tl = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_timeline);
+
+	mali_sync_tl = to_mali_sync_tl_container(sync_timeline);
+	MALI_DEBUG_ASSERT_POINTER(mali_sync_tl);
+
+	mali_tl = mali_sync_tl->timeline;
+
+	/* always signaled timeline didn't have mali container */
+	if (mali_tl) {
+		if (NULL != mali_tl->spinlock) {
+			mali_spinlock_reentrant_term(mali_tl->spinlock);
+		}
+		_mali_osk_free(mali_tl);
+	}
+
+	module_put(THIS_MODULE);
+}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static struct sync_pt *timeline_dup(struct sync_pt *pt)
+{
+	struct mali_sync_pt *mpt, *new_mpt;
+	struct sync_pt *new_pt;
+	MALI_DEBUG_ASSERT_POINTER(pt);
+
+	mpt = to_mali_sync_pt(pt);
+
+	new_pt = sync_pt_create(mpt->sync_tl, sizeof(struct mali_sync_pt));
+	if (NULL == new_pt) return NULL;
+
+	new_mpt = to_mali_sync_pt(new_pt);
+
+	mali_sync_flag_get(mpt->flag);
+	new_mpt->flag = mpt->flag;
+	new_mpt->sync_tl = mpt->sync_tl;
+
+	return new_pt;
+}
+
+static int timeline_compare(struct sync_pt *pta, struct sync_pt *ptb)
+{
+	struct mali_sync_pt *mpta;
+	struct mali_sync_pt *mptb;
+	u32 a, b;
+
+	MALI_DEBUG_ASSERT_POINTER(pta);
+	MALI_DEBUG_ASSERT_POINTER(ptb);
+	mpta = to_mali_sync_pt(pta);
+	mptb = to_mali_sync_pt(ptb);
+
+	MALI_DEBUG_ASSERT_POINTER(mpta->flag);
+	MALI_DEBUG_ASSERT_POINTER(mptb->flag);
+
+	a = mpta->flag->point;
+	b = mptb->flag->point;
+
+	if (a == b) return 0;
+
+	return ((b - a) < (a - b) ? -1 : 1);
+}
+#endif
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 17, 0)
+static void timeline_print_pt(struct seq_file *s, struct sync_pt *sync_pt)
+{
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(s);
+	MALI_DEBUG_ASSERT_POINTER(sync_pt);
+
+	mpt = to_mali_sync_pt(sync_pt);
+
+	/* It is possible this sync point is just under construct,
+	 * make sure the flag is valid before accessing it
+	*/
+	if (mpt->flag) {
+		seq_printf(s, "%u", mpt->flag->point);
+	} else {
+		seq_printf(s, "uninitialized");
+	}
+}
+
+static void timeline_print_obj(struct seq_file *s, struct sync_timeline *sync_tl)
+{
+	struct mali_sync_timeline_container *mali_sync_tl = NULL;
+	struct mali_timeline *mali_tl = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_tl);
+
+	mali_sync_tl = to_mali_sync_tl_container(sync_tl);
+	MALI_DEBUG_ASSERT_POINTER(mali_sync_tl);
+
+	mali_tl = mali_sync_tl->timeline;
+
+	if (NULL != mali_tl) {
+		seq_printf(s, "oldest (%u) ", mali_tl->point_oldest);
+		seq_printf(s, "next (%u)", mali_tl->point_next);
+		seq_printf(s, "\n");
+
+#if defined(MALI_TIMELINE_DEBUG_FUNCTIONS)
+		{
+			u32 tid = _mali_osk_get_tid();
+			struct mali_timeline_system *system = mali_tl->system;
+
+			mali_spinlock_reentrant_wait(mali_tl->spinlock, tid);
+			if (!mali_tl->destroyed) {
+				mali_spinlock_reentrant_wait(system->spinlock, tid);
+				mali_timeline_debug_print_timeline(mali_tl, s);
+				mali_spinlock_reentrant_signal(system->spinlock, tid);
+			}
+			mali_spinlock_reentrant_signal(mali_tl->spinlock, tid);
+#ifndef CONFIG_FTRACE
+			/* dump job queue status and group running status */
+			mali_executor_status_dump();
+#endif
+		}
+#endif
+	}
+}
+#elif LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static void timeline_pt_value_str(struct sync_pt *pt, char *str, int size)
+{
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(str);
+	MALI_DEBUG_ASSERT_POINTER(pt);
+
+	mpt = to_mali_sync_pt(pt);
+
+	/* It is possible this sync point is just under construct,
+	 * make sure the flag is valid before accessing it
+	*/
+	if (mpt->flag) {
+		_mali_osk_snprintf(str, size, "%u", mpt->flag->point);
+	} else {
+		_mali_osk_snprintf(str, size, "uninitialized");
+	}
+}
+
+static void timeline_value_str(struct sync_timeline *timeline, char *str, int size)
+{
+	struct mali_sync_timeline_container *mali_sync_tl = NULL;
+	struct mali_timeline *mali_tl = NULL;
+
+	MALI_DEBUG_ASSERT_POINTER(timeline);
+
+	mali_sync_tl = to_mali_sync_tl_container(timeline);
+	MALI_DEBUG_ASSERT_POINTER(mali_sync_tl);
+
+	mali_tl = mali_sync_tl->timeline;
+
+	if (NULL != mali_tl) {
+		_mali_osk_snprintf(str, size, "oldest (%u) ", mali_tl->point_oldest);
+		_mali_osk_snprintf(str, size, "next (%u)", mali_tl->point_next);
+		_mali_osk_snprintf(str, size, "\n");
+
+#if defined(MALI_TIMELINE_DEBUG_FUNCTIONS)
+		{
+			u32 tid = _mali_osk_get_tid();
+			struct mali_timeline_system *system = mali_tl->system;
+
+			mali_spinlock_reentrant_wait(mali_tl->spinlock, tid);
+			if (!mali_tl->destroyed) {
+				mali_spinlock_reentrant_wait(system->spinlock, tid);
+				mali_timeline_debug_direct_print_timeline(mali_tl);
+				mali_spinlock_reentrant_signal(system->spinlock, tid);
+			}
+			mali_spinlock_reentrant_signal(mali_tl->spinlock, tid);
+#ifndef CONFIG_FTRACE
+			/* dump job queue status and group running status */
+			mali_executor_status_dump();
+#endif
+		}
+#endif
+	}
+}
+#else
+static void timeline_print_sync_pt(struct mali_internal_sync_point *sync_pt)
+{
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_pt);
+
+	mpt = to_mali_sync_pt(sync_pt);
+
+	if (mpt->flag) {
+		MALI_DEBUG_PRINT(2, ("mali_internal_sync_pt: %u\n", mpt->flag->point));
+	} else {
+		MALI_DEBUG_PRINT(2, ("uninitialized\n", mpt->flag->point));
+	}
+}
+#endif
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+static struct sync_timeline_ops mali_timeline_ops = {
+	.driver_name    = "Mali",
+	.dup            = timeline_dup,
+	.has_signaled   = timeline_has_signaled,
+	.compare        = timeline_compare,
+	.free_pt        = timeline_free_pt,
+	.release_obj    = timeline_release,
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 17, 0)
+	.print_pt       = timeline_print_pt,
+	.print_obj      = timeline_print_obj,
+#else
+	.pt_value_str = timeline_pt_value_str,
+	.timeline_value_str = timeline_value_str,
+#endif
+};
+
+struct sync_timeline *mali_sync_timeline_create(struct mali_timeline *timeline, const char *name)
+{
+	struct sync_timeline *sync_tl;
+	struct mali_sync_timeline_container *mali_sync_tl;
+
+	sync_tl = sync_timeline_create(&mali_timeline_ops, sizeof(struct mali_sync_timeline_container), name);
+	if (NULL == sync_tl) return NULL;
+
+	mali_sync_tl = to_mali_sync_tl_container(sync_tl);
+	mali_sync_tl->timeline = timeline;
+
+	/* Grab a reference on the module to ensure the callbacks are present
+	 * as long some timeline exists. The reference is released when the
+	 * timeline is freed.
+	 * Since this function is called from a ioctl on an open file we know
+	 * we already have a reference, so using __module_get is safe. */
+	__module_get(THIS_MODULE);
+
+	return sync_tl;
+}
+
+s32 mali_sync_fence_fd_alloc(struct sync_fence *sync_fence)
+{
+	s32 fd = -1;
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 19, 0)
+	fd = get_unused_fd();
+#else
+	fd = get_unused_fd_flags(0);
+#endif
+
+	if (fd < 0) {
+		sync_fence_put(sync_fence);
+		return -1;
+	}
+	sync_fence_install(sync_fence, fd);
+
+	return fd;
+}
+
+struct sync_fence *mali_sync_fence_merge(struct sync_fence *sync_fence1, struct sync_fence *sync_fence2)
+{
+	struct sync_fence *sync_fence;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_fence1);
+	MALI_DEBUG_ASSERT_POINTER(sync_fence1);
+
+	sync_fence = sync_fence_merge("mali_merge_fence", sync_fence1, sync_fence2);
+	sync_fence_put(sync_fence1);
+	sync_fence_put(sync_fence2);
+
+	return sync_fence;
+}
+
+struct sync_fence *mali_sync_timeline_create_signaled_fence(struct sync_timeline *sync_tl)
+{
+	struct mali_sync_flag *flag;
+	struct sync_fence *sync_fence;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_tl);
+
+	flag = mali_sync_flag_create(sync_tl, 0);
+	if (NULL == flag) return NULL;
+
+	sync_fence = mali_sync_flag_create_fence(flag);
+
+	mali_sync_flag_signal(flag, 0);
+	mali_sync_flag_put(flag);
+
+	return sync_fence;
+}
+
+struct mali_sync_flag *mali_sync_flag_create(struct sync_timeline *sync_tl, mali_timeline_point point)
+{
+	struct mali_sync_flag *flag;
+
+	if (NULL == sync_tl) return NULL;
+
+	flag = _mali_osk_calloc(1, sizeof(*flag));
+	if (NULL == flag) return NULL;
+
+	flag->sync_tl = sync_tl;
+	flag->point = point;
+
+	flag->status = 0;
+	kref_init(&flag->refcount);
+
+	return flag;
+}
+
+/**
+ * Create a sync point attached to given sync flag.
+ *
+ * @note Sync points must be triggered in *exactly* the same order as they are created.
+ *
+ * @param flag Sync flag.
+ * @return New sync point if successful, NULL if not.
+ */
+static struct sync_pt *mali_sync_flag_create_pt(struct mali_sync_flag *flag)
+{
+	struct sync_pt *pt;
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(flag);
+	MALI_DEBUG_ASSERT_POINTER(flag->sync_tl);
+
+	pt = sync_pt_create(flag->sync_tl, sizeof(struct mali_sync_pt));
+	if (NULL == pt) return NULL;
+
+	mali_sync_flag_get(flag);
+
+	mpt = to_mali_sync_pt(pt);
+	mpt->flag = flag;
+	mpt->sync_tl = flag->sync_tl;
+
+	return pt;
+}
+
+struct sync_fence *mali_sync_flag_create_fence(struct mali_sync_flag *flag)
+{
+	struct sync_pt    *sync_pt;
+	struct sync_fence *sync_fence;
+
+	MALI_DEBUG_ASSERT_POINTER(flag);
+	MALI_DEBUG_ASSERT_POINTER(flag->sync_tl);
+
+	sync_pt = mali_sync_flag_create_pt(flag);
+	if (NULL == sync_pt) return NULL;
+
+	sync_fence = sync_fence_create("mali_flag_fence", sync_pt);
+	if (NULL == sync_fence) {
+		sync_pt_free(sync_pt);
+		return NULL;
+	}
+
+	return sync_fence;
+}
+#else
+static struct mali_internal_sync_timeline_ops mali_timeline_ops = {
+	.driver_name    = "Mali",
+	.has_signaled   = timeline_has_signaled,
+	.free_pt        = timeline_free_pt,
+	.release_obj    = timeline_release,
+	.print_sync_pt = timeline_print_sync_pt,
+};
+
+struct mali_internal_sync_timeline *mali_sync_timeline_create(struct mali_timeline *timeline, const char *name)
+{
+	struct mali_internal_sync_timeline *sync_tl;
+	struct mali_sync_timeline_container *mali_sync_tl;
+
+	sync_tl = mali_internal_sync_timeline_create(&mali_timeline_ops, sizeof(struct mali_sync_timeline_container), name);
+	if (NULL == sync_tl) return NULL;
+
+	mali_sync_tl = to_mali_sync_tl_container(sync_tl);
+	mali_sync_tl->timeline = timeline;
+
+	/* Grab a reference on the module to ensure the callbacks are present
+	 * as long some timeline exists. The reference is released when the
+	 * timeline is freed.
+	 * Since this function is called from a ioctl on an open file we know
+	 * we already have a reference, so using __module_get is safe. */
+	__module_get(THIS_MODULE);
+
+	return sync_tl;
+}
+
+s32 mali_sync_fence_fd_alloc(struct mali_internal_sync_fence *sync_fence)
+{
+	s32 fd = -1;
+
+	fd = get_unused_fd_flags(0);
+
+	if (fd < 0) {
+		fput(sync_fence->file);
+		return -1;
+	}
+	fd_install(fd, sync_fence->file);
+	return fd;
+}
+
+struct mali_internal_sync_fence *mali_sync_fence_merge(struct mali_internal_sync_fence *sync_fence1, struct mali_internal_sync_fence *sync_fence2)
+{
+	struct mali_internal_sync_fence *sync_fence;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_fence1);
+	MALI_DEBUG_ASSERT_POINTER(sync_fence1);
+
+	sync_fence = mali_internal_sync_fence_merge(sync_fence1, sync_fence2);
+	fput(sync_fence1->file);
+	fput(sync_fence2->file);
+
+	return sync_fence;
+}
+
+struct mali_internal_sync_fence *mali_sync_timeline_create_signaled_fence(struct mali_internal_sync_timeline *sync_tl)
+{
+	struct mali_sync_flag *flag;
+	struct mali_internal_sync_fence *sync_fence;
+
+	MALI_DEBUG_ASSERT_POINTER(sync_tl);
+
+	flag = mali_sync_flag_create(sync_tl, 0);
+	if (NULL == flag) return NULL;
+
+	sync_fence = mali_sync_flag_create_fence(flag);
+
+	mali_sync_flag_signal(flag, 0);
+	mali_sync_flag_put(flag);
+
+	return sync_fence;
+}
+
+struct mali_sync_flag *mali_sync_flag_create(struct mali_internal_sync_timeline *sync_tl, mali_timeline_point point)
+{
+	struct mali_sync_flag *flag;
+
+	if (NULL == sync_tl) return NULL;
+
+	flag = _mali_osk_calloc(1, sizeof(*flag));
+	if (NULL == flag) return NULL;
+
+	flag->sync_tl = sync_tl;
+	flag->point = point;
+
+	flag->status = 0;
+	kref_init(&flag->refcount);
+
+	return flag;
+}
+
+/**
+ * Create a sync point attached to given sync flag.
+ *
+ * @note Sync points must be triggered in *exactly* the same order as they are created.
+ *
+ * @param flag Sync flag.
+ * @return New sync point if successful, NULL if not.
+ */
+static struct mali_internal_sync_point *mali_sync_flag_create_pt(struct mali_sync_flag *flag)
+{
+	struct mali_internal_sync_point *pt;
+	struct mali_sync_pt *mpt;
+
+	MALI_DEBUG_ASSERT_POINTER(flag);
+	MALI_DEBUG_ASSERT_POINTER(flag->sync_tl);
+
+	pt = mali_internal_sync_point_create(flag->sync_tl, sizeof(struct mali_sync_pt));
+
+	if (pt == NULL) {
+		MALI_PRINT_ERROR(("Mali sync: sync_pt creation failed\n"));
+		return NULL;
+	}
+	mali_sync_flag_get(flag);
+
+	mpt = to_mali_sync_pt(pt);
+	mpt->flag = flag;
+	mpt->sync_tl = flag->sync_tl;
+
+	return pt;
+}
+
+struct mali_internal_sync_fence *mali_sync_flag_create_fence(struct mali_sync_flag *flag)
+{
+	struct mali_internal_sync_point    *sync_pt;
+	struct mali_internal_sync_fence *sync_fence;
+
+	MALI_DEBUG_ASSERT_POINTER(flag);
+	MALI_DEBUG_ASSERT_POINTER(flag->sync_tl);
+
+	sync_pt = mali_sync_flag_create_pt(flag);
+	if (NULL == sync_pt) {
+		MALI_PRINT_ERROR(("Mali sync: sync_pt creation failed\n"));
+		return NULL;
+	}
+	sync_fence = (struct mali_internal_sync_fence *)sync_file_create(&sync_pt->base);
+	if (NULL == sync_fence) {
+		MALI_PRINT_ERROR(("Mali sync: sync_fence creation failed\n"));
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 10, 0)
+		dma_fence_put(&sync_pt->base);
+#else
+		fence_put(&sync_pt->base);
+#endif
+		return NULL;
+	}
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 10, 0)
+	fence_put(&sync_pt->base);
+#else
+	dma_fence_put(&sync_pt->base);
+#endif
+
+	return sync_fence;
+}
+#endif
+
+void mali_sync_flag_get(struct mali_sync_flag *flag)
+{
+	MALI_DEBUG_ASSERT_POINTER(flag);
+	kref_get(&flag->refcount);
+}
+
+/**
+ * Free sync flag.
+ *
+ * @param ref kref object embedded in sync flag that should be freed.
+ */
+static void mali_sync_flag_free(struct kref *ref)
+{
+	struct mali_sync_flag *flag;
+
+	MALI_DEBUG_ASSERT_POINTER(ref);
+	flag = container_of(ref, struct mali_sync_flag, refcount);
+
+	_mali_osk_free(flag);
+}
+
+void mali_sync_flag_put(struct mali_sync_flag *flag)
+{
+	MALI_DEBUG_ASSERT_POINTER(flag);
+	kref_put(&flag->refcount, mali_sync_flag_free);
+}
+
+void mali_sync_flag_signal(struct mali_sync_flag *flag, int error)
+{
+	MALI_DEBUG_ASSERT_POINTER(flag);
+
+	MALI_DEBUG_ASSERT(0 == flag->status);
+	flag->status = (0 > error) ? error : 1;
+
+	_mali_osk_write_mem_barrier();
+#if  LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+	sync_timeline_signal(flag->sync_tl);
+#else
+	mali_internal_sync_timeline_signal(flag->sync_tl);
+#endif
+}
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_sync.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_sync.h
@@ -0,0 +1,169 @@
+/*
+ * Copyright (C) 2012-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_sync.h
+ *
+ * Mali interface for Linux sync objects.
+ */
+
+#ifndef _MALI_SYNC_H_
+#define _MALI_SYNC_H_
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+
+#include <linux/seq_file.h>
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(3, 10, 0)
+#include <linux/sync.h>
+#elif LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+#include <sync.h>
+#else
+#include "mali_internal_sync.h"
+#endif
+
+
+#include "mali_osk.h"
+
+struct mali_sync_flag;
+struct mali_timeline;
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 6, 0)
+/**
+ * Create a sync timeline.
+ *
+ * @param name Name of the sync timeline.
+ * @return The new sync timeline if successful, NULL if not.
+ */
+struct sync_timeline *mali_sync_timeline_create(struct mali_timeline *timeline, const char *name);
+
+/**
+ * Creates a file descriptor representing the sync fence.  Will release sync fence if allocation of
+ * file descriptor fails.
+ *
+ * @param sync_fence Sync fence.
+ * @return File descriptor representing sync fence if successful, or -1 if not.
+ */
+s32 mali_sync_fence_fd_alloc(struct sync_fence *sync_fence);
+
+/**
+ * Merges two sync fences.  Both input sync fences will be released.
+ *
+ * @param sync_fence1 First sync fence.
+ * @param sync_fence2 Second sync fence.
+ * @return New sync fence that is the result of the merger if successful, or NULL if not.
+ */
+struct sync_fence *mali_sync_fence_merge(struct sync_fence *sync_fence1, struct sync_fence *sync_fence2);
+
+/**
+ * Create a sync fence that is already signaled.
+ *
+ * @param tl Sync timeline.
+ * @return New signaled sync fence if successful, NULL if not.
+ */
+struct sync_fence *mali_sync_timeline_create_signaled_fence(struct sync_timeline *sync_tl);
+
+
+/**
+ * Create a sync flag.
+ *
+ * @param sync_tl Sync timeline.
+ * @param point Point on Mali timeline.
+ * @return New sync flag if successful, NULL if not.
+ */
+struct mali_sync_flag *mali_sync_flag_create(struct sync_timeline *sync_tl, u32 point);
+
+/**
+ * Create a sync fence attached to given sync flag.
+ *
+ * @param flag Sync flag.
+ * @return New sync fence if successful, NULL if not.
+ */
+struct sync_fence *mali_sync_flag_create_fence(struct mali_sync_flag *flag);
+#else
+/**
+ * Create a sync timeline.
+ *
+ * @param name Name of the sync timeline.
+ * @return The new sync timeline if successful, NULL if not.
+ */
+struct mali_internal_sync_timeline *mali_sync_timeline_create(struct mali_timeline *timeline, const char *name);
+
+/**
+ * Creates a file descriptor representing the sync fence.  Will release sync fence if allocation of
+ * file descriptor fails.
+ *
+ * @param sync_fence Sync fence.
+ * @return File descriptor representing sync fence if successful, or -1 if not.
+ */
+s32 mali_sync_fence_fd_alloc(struct mali_internal_sync_fence *sync_fence);
+
+/**
+ * Merges two sync fences.  Both input sync fences will be released.
+ *
+ * @param sync_fence1 First sync fence.
+ * @param sync_fence2 Second sync fence.
+ * @return New sync fence that is the result of the merger if successful, or NULL if not.
+ */
+struct mali_internal_sync_fence *mali_sync_fence_merge(struct mali_internal_sync_fence *sync_fence1, struct mali_internal_sync_fence *sync_fence2);
+
+/**
+ * Create a sync fence that is already signaled.
+ *
+ * @param tl Sync timeline.
+ * @return New signaled sync fence if successful, NULL if not.
+ */
+struct mali_internal_sync_fence *mali_sync_timeline_create_signaled_fence(struct mali_internal_sync_timeline *sync_tl);
+
+
+/**
+ * Create a sync flag.
+ *
+ * @param sync_tl Sync timeline.
+ * @param point Point on Mali timeline.
+ * @return New sync flag if successful, NULL if not.
+ */
+struct mali_sync_flag *mali_sync_flag_create(struct mali_internal_sync_timeline *sync_tl, u32 point);
+
+/**
+ * Create a sync fence attached to given sync flag.
+ *
+ * @param flag Sync flag.
+ * @return New sync fence if successful, NULL if not.
+ */
+struct mali_internal_sync_fence *mali_sync_flag_create_fence(struct mali_sync_flag *flag);
+
+#endif
+/**
+ * Grab sync flag reference.
+ *
+ * @param flag Sync flag.
+ */
+void mali_sync_flag_get(struct mali_sync_flag *flag);
+
+/**
+ * Release sync flag reference.  If this was the last reference, the sync flag will be freed.
+ *
+ * @param flag Sync flag.
+ */
+void mali_sync_flag_put(struct mali_sync_flag *flag);
+
+/**
+ * Signal sync flag.  All sync fences created from this flag will be signaled.
+ *
+ * @param flag Sync flag to signal.
+ * @param error Negative error code, or 0 if no error.
+ */
+void mali_sync_flag_signal(struct mali_sync_flag *flag, int error);
+
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+#endif /* _MALI_SYNC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_uk_types.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_uk_types.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2012, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_UK_TYPES_H__
+#define __MALI_UK_TYPES_H__
+
+/* Simple wrapper in order to find the OS specific location of this file */
+#include <linux/mali/mali_utgard_uk_types.h>
+
+#endif /* __MALI_UK_TYPES_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_core.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_core.c
@@ -0,0 +1,151 @@
+/*
+ * Copyright (C) 2010-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/slab.h>     /* memort allocation functions */
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+int get_api_version_wrapper(struct mali_session_data *session_data, _mali_uk_get_api_version_s __user *uargs)
+{
+	_mali_uk_get_api_version_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != get_user(kargs.version, &uargs->version)) return -EFAULT;
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_get_api_version(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	if (0 != put_user(kargs.version, &uargs->version)) return -EFAULT;
+	if (0 != put_user(kargs.compatible, &uargs->compatible)) return -EFAULT;
+
+	return 0;
+}
+
+int get_api_version_v2_wrapper(struct mali_session_data *session_data, _mali_uk_get_api_version_v2_s __user *uargs)
+{
+	_mali_uk_get_api_version_v2_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != get_user(kargs.version, &uargs->version)) return -EFAULT;
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_get_api_version_v2(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	if (0 != put_user(kargs.version, &uargs->version)) return -EFAULT;
+	if (0 != put_user(kargs.compatible, &uargs->compatible)) return -EFAULT;
+
+	return 0;
+}
+
+int wait_for_notification_wrapper(struct mali_session_data *session_data, _mali_uk_wait_for_notification_s __user *uargs)
+{
+	_mali_uk_wait_for_notification_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_wait_for_notification(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	if (_MALI_NOTIFICATION_CORE_SHUTDOWN_IN_PROGRESS != kargs.type) {
+		kargs.ctx = (uintptr_t)NULL; /* prevent kernel address to be returned to user space */
+		if (0 != copy_to_user(uargs, &kargs, sizeof(_mali_uk_wait_for_notification_s))) return -EFAULT;
+	} else {
+		if (0 != put_user(kargs.type, &uargs->type)) return -EFAULT;
+	}
+
+	return 0;
+}
+
+int post_notification_wrapper(struct mali_session_data *session_data, _mali_uk_post_notification_s __user *uargs)
+{
+	_mali_uk_post_notification_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+
+	if (0 != get_user(kargs.type, &uargs->type)) {
+		return -EFAULT;
+	}
+
+	err = _mali_ukk_post_notification(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
+int get_user_settings_wrapper(struct mali_session_data *session_data, _mali_uk_get_user_settings_s __user *uargs)
+{
+	_mali_uk_get_user_settings_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_get_user_settings(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	kargs.ctx = 0; /* prevent kernel address to be returned to user space */
+	if (0 != copy_to_user(uargs, &kargs, sizeof(_mali_uk_get_user_settings_s))) return -EFAULT;
+
+	return 0;
+}
+
+int request_high_priority_wrapper(struct mali_session_data *session_data, _mali_uk_request_high_priority_s __user *uargs)
+{
+	_mali_uk_request_high_priority_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_request_high_priority(&kargs);
+
+	kargs.ctx = 0;
+
+	return map_errcode(err);
+}
+
+int pending_submit_wrapper(struct mali_session_data *session_data, _mali_uk_pending_submit_s __user *uargs)
+{
+	_mali_uk_pending_submit_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_pending_submit(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_gp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_gp.c
@@ -0,0 +1,96 @@
+/*
+ * Copyright (C) 2010, 2012-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+int gp_start_job_wrapper(struct mali_session_data *session_data, _mali_uk_gp_start_job_s __user *uargs)
+{
+	_mali_osk_errcode_t err;
+
+	/* If the job was started successfully, 0 is returned.  If there was an error, but the job
+	 * was started, we return -ENOENT.  For anything else returned, the job was not started. */
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	err = _mali_ukk_gp_start_job(session_data, uargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	return 0;
+}
+
+int gp_get_core_version_wrapper(struct mali_session_data *session_data, _mali_uk_get_gp_core_version_s __user *uargs)
+{
+	_mali_uk_get_gp_core_version_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err =  _mali_ukk_get_gp_core_version(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	/* no known transactions to roll-back */
+
+	if (0 != put_user(kargs.version, &uargs->version)) return -EFAULT;
+
+	return 0;
+}
+
+int gp_suspend_response_wrapper(struct mali_session_data *session_data, _mali_uk_gp_suspend_response_s __user *uargs)
+{
+	_mali_uk_gp_suspend_response_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_gp_suspend_response_s))) return -EFAULT;
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_gp_suspend_response(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	if (0 != put_user(kargs.cookie, &uargs->cookie)) return -EFAULT;
+
+	/* no known transactions to roll-back */
+	return 0;
+}
+
+int gp_get_number_of_cores_wrapper(struct mali_session_data *session_data, _mali_uk_get_gp_number_of_cores_s __user *uargs)
+{
+	_mali_uk_get_gp_number_of_cores_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_get_gp_number_of_cores(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	/* no known transactions to roll-back */
+
+	if (0 != put_user(kargs.number_of_cores, &uargs->number_of_cores)) return -EFAULT;
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_mem.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_mem.c
@@ -0,0 +1,347 @@
+/*
+ * Copyright (C) 2010-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+int mem_alloc_wrapper(struct mali_session_data *session_data, _mali_uk_alloc_mem_s __user *uargs)
+{
+	_mali_uk_alloc_mem_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_alloc_mem_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_allocate(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	if (0 != put_user(kargs.backend_handle, &uargs->backend_handle)) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+int mem_free_wrapper(struct mali_session_data *session_data, _mali_uk_free_mem_s __user *uargs)
+{
+	_mali_uk_free_mem_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_free_mem_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_free(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	if (0 != put_user(kargs.free_pages_nr, &uargs->free_pages_nr)) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+int mem_bind_wrapper(struct mali_session_data *session_data, _mali_uk_bind_mem_s __user *uargs)
+{
+	_mali_uk_bind_mem_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_bind_mem_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_bind(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
+int mem_unbind_wrapper(struct mali_session_data *session_data, _mali_uk_unbind_mem_s __user *uargs)
+{
+	_mali_uk_unbind_mem_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_unbind_mem_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_unbind(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
+
+int mem_cow_wrapper(struct mali_session_data *session_data, _mali_uk_cow_mem_s __user *uargs)
+{
+	_mali_uk_cow_mem_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_cow_mem_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_cow(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	if (0 != put_user(kargs.backend_handle, &uargs->backend_handle)) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+int mem_cow_modify_range_wrapper(struct mali_session_data *session_data, _mali_uk_cow_modify_range_s __user *uargs)
+{
+	_mali_uk_cow_modify_range_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_cow_modify_range_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_cow_modify_range(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	if (0 != put_user(kargs.change_pages_nr, &uargs->change_pages_nr)) {
+		return -EFAULT;
+	}
+	return 0;
+}
+
+
+int mem_resize_mem_wrapper(struct mali_session_data *session_data, _mali_uk_mem_resize_s __user *uargs)
+{
+	_mali_uk_mem_resize_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_mem_resize_s))) {
+		return -EFAULT;
+	}
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_mem_resize(&kargs);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
+int mem_write_safe_wrapper(struct mali_session_data *session_data, _mali_uk_mem_write_safe_s __user *uargs)
+{
+	_mali_uk_mem_write_safe_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_mem_write_safe_s))) {
+		return -EFAULT;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+
+	/* Check if we can access the buffers */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 0, 0)
+	if (!access_ok((const void __user *)kargs.dest, kargs.size)
+	    || !access_ok((const void __user *)kargs.src, kargs.size)) {
+#else
+	if (!access_ok(VERIFY_WRITE, kargs.dest, kargs.size)
+	    || !access_ok(VERIFY_READ, kargs.src, kargs.size)) {
+#endif
+		return -EINVAL;
+	}
+
+	/* Check if size wraps */
+	if ((kargs.size + kargs.dest) <= kargs.dest
+	    || (kargs.size + kargs.src) <= kargs.src) {
+		return -EINVAL;
+	}
+
+	err = _mali_ukk_mem_write_safe(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	if (0 != put_user(kargs.size, &uargs->size)) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+
+
+int mem_query_mmu_page_table_dump_size_wrapper(struct mali_session_data *session_data, _mali_uk_query_mmu_page_table_dump_size_s __user *uargs)
+{
+	_mali_uk_query_mmu_page_table_dump_size_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_query_mmu_page_table_dump_size(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	if (0 != put_user(kargs.size, &uargs->size)) return -EFAULT;
+
+	return 0;
+}
+
+int mem_dump_mmu_page_table_wrapper(struct mali_session_data *session_data, _mali_uk_dump_mmu_page_table_s __user *uargs)
+{
+	_mali_uk_dump_mmu_page_table_s kargs;
+	_mali_osk_errcode_t err;
+	void __user *user_buffer;
+	void *buffer = NULL;
+	int rc = -EFAULT;
+
+	/* validate input */
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	/* the session_data pointer was validated by caller */
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_dump_mmu_page_table_s)))
+		goto err_exit;
+
+	user_buffer = (void __user *)(uintptr_t)kargs.buffer;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 0, 0)
+	if (!access_ok(user_buffer, kargs.size))
+#else
+	if (!access_ok(VERIFY_WRITE, user_buffer, kargs.size))
+#endif
+		goto err_exit;
+
+	/* allocate temporary buffer (kernel side) to store mmu page table info */
+	if (kargs.size <= 0)
+		return -EINVAL;
+	/* Allow at most 8MiB buffers, this is more than enough to dump a fully
+	 * populated page table. */
+	if (kargs.size > SZ_8M)
+		return -EINVAL;
+
+	buffer = (void *)(uintptr_t)_mali_osk_valloc(kargs.size);
+	if (NULL == buffer) {
+		rc = -ENOMEM;
+		goto err_exit;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+	kargs.buffer = (uintptr_t)buffer;
+	err = _mali_ukk_dump_mmu_page_table(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		rc = map_errcode(err);
+		goto err_exit;
+	}
+
+	/* copy mmu page table info back to user space and update pointers */
+	if (0 != copy_to_user(user_buffer, buffer, kargs.size))
+		goto err_exit;
+
+	kargs.register_writes = kargs.register_writes -
+				(uintptr_t)buffer + (uintptr_t)user_buffer;
+	kargs.page_table_dump = kargs.page_table_dump -
+				(uintptr_t)buffer + (uintptr_t)user_buffer;
+
+	if (0 != copy_to_user(uargs, &kargs, sizeof(kargs)))
+		goto err_exit;
+
+	rc = 0;
+
+err_exit:
+	if (buffer) _mali_osk_vfree(buffer);
+	return rc;
+}
+
+int mem_usage_get_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_memory_usage_get_s __user *uargs)
+{
+	_mali_osk_errcode_t err;
+	_mali_uk_profiling_memory_usage_get_s kargs;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_profiling_memory_usage_get_s))) {
+		return -EFAULT;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_mem_usage_get(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	kargs.ctx = (uintptr_t)NULL; /* prevent kernel address to be returned to user space */
+	if (0 != copy_to_user(uargs, &kargs, sizeof(_mali_uk_profiling_memory_usage_get_s))) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_pp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_pp.c
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2010, 2012-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+int pp_start_job_wrapper(struct mali_session_data *session_data, _mali_uk_pp_start_job_s __user *uargs)
+{
+	_mali_osk_errcode_t err;
+
+	/* If the job was started successfully, 0 is returned.  If there was an error, but the job
+	 * was started, we return -ENOENT.  For anything else returned, the job was not started. */
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	err = _mali_ukk_pp_start_job(session_data, uargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	return 0;
+}
+
+int pp_and_gp_start_job_wrapper(struct mali_session_data *session_data, _mali_uk_pp_and_gp_start_job_s __user *uargs)
+{
+	_mali_osk_errcode_t err;
+
+	/* If the jobs were started successfully, 0 is returned.  If there was an error, but the
+	 * jobs were started, we return -ENOENT.  For anything else returned, the jobs were not
+	 * started. */
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	err = _mali_ukk_pp_and_gp_start_job(session_data, uargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	return 0;
+}
+
+int pp_get_number_of_cores_wrapper(struct mali_session_data *session_data, _mali_uk_get_pp_number_of_cores_s __user *uargs)
+{
+	_mali_uk_get_pp_number_of_cores_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+
+	err = _mali_ukk_get_pp_number_of_cores(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	kargs.ctx = (uintptr_t)NULL; /* prevent kernel address to be returned to user space */
+	if (0 != copy_to_user(uargs, &kargs, sizeof(_mali_uk_get_pp_number_of_cores_s))) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+int pp_get_core_version_wrapper(struct mali_session_data *session_data, _mali_uk_get_pp_core_version_s __user *uargs)
+{
+	_mali_uk_get_pp_core_version_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_get_pp_core_version(&kargs);
+	if (_MALI_OSK_ERR_OK != err) return map_errcode(err);
+
+	if (0 != put_user(kargs.version, &uargs->version)) return -EFAULT;
+
+	return 0;
+}
+
+int pp_disable_wb_wrapper(struct mali_session_data *session_data, _mali_uk_pp_disable_wb_s __user *uargs)
+{
+	_mali_uk_pp_disable_wb_s kargs;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session_data, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_pp_disable_wb_s))) return -EFAULT;
+
+	kargs.ctx = (uintptr_t)session_data;
+	_mali_ukk_pp_job_disable_wb(&kargs);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_profiling.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_profiling.c
@@ -0,0 +1,189 @@
+/*
+ * Copyright (C) 2010-2015, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+#include <linux/slab.h>
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+int profiling_add_event_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_add_event_s __user *uargs)
+{
+	_mali_uk_profiling_add_event_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_profiling_add_event_s))) {
+		return -EFAULT;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_profiling_add_event(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
+int profiling_report_sw_counters_wrapper(struct mali_session_data *session_data, _mali_uk_sw_counters_report_s __user *uargs)
+{
+	_mali_uk_sw_counters_report_s kargs;
+	_mali_osk_errcode_t err;
+	u32 *counter_buffer;
+	u32 __user *counters;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_sw_counters_report_s))) {
+		return -EFAULT;
+	}
+
+	/* make sure that kargs.num_counters is [at least somewhat] sane */
+	if (kargs.num_counters > 10000) {
+		MALI_DEBUG_PRINT(1, ("User space attempted to allocate too many counters.\n"));
+		return -EINVAL;
+	}
+
+	counter_buffer = (u32 *)kmalloc(sizeof(u32) * kargs.num_counters, GFP_KERNEL);
+	if (NULL == counter_buffer) {
+		return -ENOMEM;
+	}
+
+	counters = (u32 *)(uintptr_t)kargs.counters;
+
+	if (0 != copy_from_user(counter_buffer, counters, sizeof(u32) * kargs.num_counters)) {
+		kfree(counter_buffer);
+		return -EFAULT;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+	kargs.counters = (uintptr_t)counter_buffer;
+
+	err = _mali_ukk_sw_counters_report(&kargs);
+
+	kfree(counter_buffer);
+
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
+int profiling_get_stream_fd_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_stream_fd_get_s __user *uargs)
+{
+	_mali_uk_profiling_stream_fd_get_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_profiling_stream_fd_get_s))) {
+		return -EFAULT;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_profiling_stream_fd_get(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	if (0 != copy_to_user(uargs, &kargs, sizeof(_mali_uk_profiling_stream_fd_get_s))) {
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+int profiling_control_set_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_control_set_s __user *uargs)
+{
+	_mali_uk_profiling_control_set_s kargs;
+	_mali_osk_errcode_t err;
+	u8 *kernel_control_data = NULL;
+	u8 *kernel_response_data = NULL;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != get_user(kargs.control_packet_size, &uargs->control_packet_size)) return -EFAULT;
+	if (0 != get_user(kargs.response_packet_size, &uargs->response_packet_size)) return -EFAULT;
+
+	kargs.ctx = (uintptr_t)session_data;
+
+
+	/* Sanity check about the size */
+	if (kargs.control_packet_size > PAGE_SIZE || kargs.response_packet_size > PAGE_SIZE)
+		return -EINVAL;
+
+	if (0 !=  kargs.control_packet_size) {
+
+		if (0 == kargs.response_packet_size)
+			return -EINVAL;
+
+		kernel_control_data = _mali_osk_calloc(1, kargs.control_packet_size);
+		if (NULL == kernel_control_data) {
+			return -ENOMEM;
+		}
+
+		kernel_response_data = _mali_osk_calloc(1, kargs.response_packet_size);
+		if (NULL == kernel_response_data) {
+			_mali_osk_free(kernel_control_data);
+			return -ENOMEM;
+		}
+
+		kargs.control_packet_data = (uintptr_t)kernel_control_data;
+		kargs.response_packet_data = (uintptr_t)kernel_response_data;
+
+		if (0 != copy_from_user((void *)(uintptr_t)kernel_control_data, (void *)(uintptr_t)uargs->control_packet_data, kargs.control_packet_size)) {
+			_mali_osk_free(kernel_control_data);
+			_mali_osk_free(kernel_response_data);
+			return -EFAULT;
+		}
+
+		err = _mali_ukk_profiling_control_set(&kargs);
+		if (_MALI_OSK_ERR_OK != err) {
+			_mali_osk_free(kernel_control_data);
+			_mali_osk_free(kernel_response_data);
+			return map_errcode(err);
+		}
+
+		if (0 != kargs.response_packet_size && 0 != copy_to_user(((void *)(uintptr_t)uargs->response_packet_data), ((void *)(uintptr_t)kargs.response_packet_data), kargs.response_packet_size)) {
+			_mali_osk_free(kernel_control_data);
+			_mali_osk_free(kernel_response_data);
+			return -EFAULT;
+		}
+
+		if (0 != put_user(kargs.response_packet_size, &uargs->response_packet_size)) {
+			_mali_osk_free(kernel_control_data);
+			_mali_osk_free(kernel_response_data);
+			return -EFAULT;
+		}
+
+		_mali_osk_free(kernel_control_data);
+		_mali_osk_free(kernel_response_data);
+	} else {
+
+		err = _mali_ukk_profiling_control_set(&kargs);
+		if (_MALI_OSK_ERR_OK != err) {
+			return map_errcode(err);
+		}
+
+	}
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_soft_job.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_soft_job.c
@@ -0,0 +1,96 @@
+/*
+ * Copyright (C) 2013-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+#include "mali_soft_job.h"
+#include "mali_timeline.h"
+
+int soft_job_start_wrapper(struct mali_session_data *session, _mali_uk_soft_job_start_s __user *uargs)
+{
+	_mali_uk_soft_job_start_s kargs;
+	u32 type, point;
+	u64 user_job;
+	struct mali_timeline_fence fence;
+	struct mali_soft_job *job = NULL;
+	u32 __user *job_id_ptr = NULL;
+
+	/* If the job was started successfully, 0 is returned.  If there was an error, but the job
+	 * was started, we return -ENOENT.  For anything else returned, the job was not started. */
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+	MALI_CHECK_NON_NULL(session, -EINVAL);
+
+	MALI_DEBUG_ASSERT_POINTER(session->soft_job_system);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(kargs))) {
+		return -EFAULT;
+	}
+
+	type = kargs.type;
+	user_job = kargs.user_job;
+	job_id_ptr = (u32 __user *)(uintptr_t)kargs.job_id_ptr;
+
+	mali_timeline_fence_copy_uk_fence(&fence, &kargs.fence);
+
+	if ((MALI_SOFT_JOB_TYPE_USER_SIGNALED != type) && (MALI_SOFT_JOB_TYPE_SELF_SIGNALED != type)) {
+		MALI_DEBUG_PRINT_ERROR(("Invalid soft job type specified\n"));
+		return -EINVAL;
+	}
+
+	/* Create soft job. */
+	job = mali_soft_job_create(session->soft_job_system, (enum mali_soft_job_type)type, user_job);
+	if (unlikely(NULL == job)) {
+		return map_errcode(_MALI_OSK_ERR_NOMEM);
+	}
+
+	/* Write job id back to user space. */
+	if (0 != put_user(job->id, job_id_ptr)) {
+		MALI_PRINT_ERROR(("Mali Soft Job: failed to put job id"));
+		mali_soft_job_destroy(job);
+		return map_errcode(_MALI_OSK_ERR_NOMEM);
+	}
+
+	/* Start soft job. */
+	point = mali_soft_job_start(job, &fence);
+
+	if (0 != put_user(point, &uargs->point)) {
+		/* Let user space know that something failed after the job was started. */
+		return -ENOENT;
+	}
+
+	return 0;
+}
+
+int soft_job_signal_wrapper(struct mali_session_data *session, _mali_uk_soft_job_signal_s __user *uargs)
+{
+	u32 job_id;
+	_mali_osk_errcode_t err;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (0 != get_user(job_id, &uargs->job_id)) return -EFAULT;
+
+	err = mali_soft_job_system_signal_job(session->soft_job_system, job_id);
+
+	return map_errcode(err);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_timeline.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_timeline.c
@@ -0,0 +1,94 @@
+/*
+ * Copyright (C) 2013, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+#include "mali_timeline.h"
+#include "mali_timeline_fence_wait.h"
+#include "mali_timeline_sync_fence.h"
+
+int timeline_get_latest_point_wrapper(struct mali_session_data *session, _mali_uk_timeline_get_latest_point_s __user *uargs)
+{
+	u32 val;
+	mali_timeline_id timeline;
+	mali_timeline_point point;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (0 != get_user(val, &uargs->timeline)) return -EFAULT;
+
+	if (MALI_UK_TIMELINE_MAX <= val) {
+		return -EINVAL;
+	}
+
+	timeline = (mali_timeline_id)val;
+
+	point = mali_timeline_system_get_latest_point(session->timeline_system, timeline);
+
+	if (0 != put_user(point, &uargs->point)) return -EFAULT;
+
+	return 0;
+}
+
+int timeline_wait_wrapper(struct mali_session_data *session, _mali_uk_timeline_wait_s __user *uargs)
+{
+	u32 timeout, status;
+	mali_bool ret;
+	_mali_uk_fence_t uk_fence;
+	struct mali_timeline_fence fence;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (0 != copy_from_user(&uk_fence, &uargs->fence, sizeof(_mali_uk_fence_t))) return -EFAULT;
+	if (0 != get_user(timeout, &uargs->timeout)) return -EFAULT;
+
+	mali_timeline_fence_copy_uk_fence(&fence, &uk_fence);
+
+	ret = mali_timeline_fence_wait(session->timeline_system, &fence, timeout);
+	status = (MALI_TRUE == ret ? 1 : 0);
+
+	if (0 != put_user(status, &uargs->status)) return -EFAULT;
+
+	return 0;
+}
+
+int timeline_create_sync_fence_wrapper(struct mali_session_data *session, _mali_uk_timeline_create_sync_fence_s __user *uargs)
+{
+	s32 sync_fd = -1;
+	_mali_uk_fence_t uk_fence;
+	struct mali_timeline_fence fence;
+
+	MALI_DEBUG_ASSERT_POINTER(session);
+
+	if (0 != copy_from_user(&uk_fence, &uargs->fence, sizeof(_mali_uk_fence_t))) return -EFAULT;
+	mali_timeline_fence_copy_uk_fence(&fence, &uk_fence);
+
+#if defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE)
+	sync_fd = mali_timeline_sync_fence_create(session->timeline_system, &fence);
+#else
+	sync_fd = -1;
+#endif /* defined(CONFIG_SYNC) || defined(CONFIG_SYNC_FILE) */
+
+	if (0 != put_user(sync_fd, &uargs->sync_fd)) return -EFAULT;
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_vsync.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_vsync.c
@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2011-2014, 2017-2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+#include <linux/fs.h>       /* file system operations */
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4,12,0)
+#include <linux/uaccess.h>
+#else
+#include <asm/uaccess.h>
+#endif
+
+#include "mali_ukk.h"
+#include "mali_osk.h"
+#include "mali_kernel_common.h"
+#include "mali_session.h"
+#include "mali_ukk_wrappers.h"
+
+
+int vsync_event_report_wrapper(struct mali_session_data *session_data, _mali_uk_vsync_event_report_s __user *uargs)
+{
+	_mali_uk_vsync_event_report_s kargs;
+	_mali_osk_errcode_t err;
+
+	MALI_CHECK_NON_NULL(uargs, -EINVAL);
+
+	if (0 != copy_from_user(&kargs, uargs, sizeof(_mali_uk_vsync_event_report_s))) {
+		return -EFAULT;
+	}
+
+	kargs.ctx = (uintptr_t)session_data;
+	err = _mali_ukk_vsync_event_report(&kargs);
+	if (_MALI_OSK_ERR_OK != err) {
+		return map_errcode(err);
+	}
+
+	return 0;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/linux/mali_ukk_wrappers.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/linux/mali_ukk_wrappers.h
@@ -0,0 +1,75 @@
+/*
+ * Copyright (C) 2010-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_ukk_wrappers.h
+ * Defines the wrapper functions for each user-kernel function
+ */
+
+#ifndef __MALI_UKK_WRAPPERS_H__
+#define __MALI_UKK_WRAPPERS_H__
+
+#include "mali_uk_types.h"
+#include "mali_osk.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+int wait_for_notification_wrapper(struct mali_session_data *session_data, _mali_uk_wait_for_notification_s __user *uargs);
+int get_api_version_wrapper(struct mali_session_data *session_data, _mali_uk_get_api_version_s __user *uargs);
+int get_api_version_v2_wrapper(struct mali_session_data *session_data, _mali_uk_get_api_version_v2_s __user *uargs);
+int get_user_settings_wrapper(struct mali_session_data *session_data, _mali_uk_get_user_settings_s __user *uargs);
+int post_notification_wrapper(struct mali_session_data *session_data, _mali_uk_post_notification_s __user *uargs);
+int request_high_priority_wrapper(struct mali_session_data *session_data, _mali_uk_request_high_priority_s __user *uargs);
+int pending_submit_wrapper(struct mali_session_data *session_data, _mali_uk_pending_submit_s __user *uargs);
+
+int mem_alloc_wrapper(struct mali_session_data *session_data, _mali_uk_alloc_mem_s __user *uargs);
+int mem_free_wrapper(struct mali_session_data *session_data, _mali_uk_free_mem_s __user *uargs);
+int mem_bind_wrapper(struct mali_session_data *session_data, _mali_uk_bind_mem_s __user *uargs);
+int mem_unbind_wrapper(struct mali_session_data *session_data, _mali_uk_unbind_mem_s __user *uargs);
+int mem_cow_wrapper(struct mali_session_data *session_data, _mali_uk_cow_mem_s __user *uargs);
+int mem_cow_modify_range_wrapper(struct mali_session_data *session_data, _mali_uk_cow_modify_range_s __user *uargs);
+int mem_resize_mem_wrapper(struct mali_session_data *session_data, _mali_uk_mem_resize_s __user *uargs);
+int mem_write_safe_wrapper(struct mali_session_data *session_data, _mali_uk_mem_write_safe_s __user *uargs);
+int mem_query_mmu_page_table_dump_size_wrapper(struct mali_session_data *session_data, _mali_uk_query_mmu_page_table_dump_size_s __user *uargs);
+int mem_dump_mmu_page_table_wrapper(struct mali_session_data *session_data, _mali_uk_dump_mmu_page_table_s __user *uargs);
+int mem_usage_get_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_memory_usage_get_s __user *uargs);
+
+int timeline_get_latest_point_wrapper(struct mali_session_data *session, _mali_uk_timeline_get_latest_point_s __user *uargs);
+int timeline_wait_wrapper(struct mali_session_data *session, _mali_uk_timeline_wait_s __user *uargs);
+int timeline_create_sync_fence_wrapper(struct mali_session_data *session, _mali_uk_timeline_create_sync_fence_s __user *uargs);
+int soft_job_start_wrapper(struct mali_session_data *session, _mali_uk_soft_job_start_s __user *uargs);
+int soft_job_signal_wrapper(struct mali_session_data *session, _mali_uk_soft_job_signal_s __user *uargs);
+int pp_start_job_wrapper(struct mali_session_data *session_data, _mali_uk_pp_start_job_s __user *uargs);
+int pp_and_gp_start_job_wrapper(struct mali_session_data *session_data, _mali_uk_pp_and_gp_start_job_s __user *uargs);
+int pp_get_number_of_cores_wrapper(struct mali_session_data *session_data, _mali_uk_get_pp_number_of_cores_s __user *uargs);
+int pp_get_core_version_wrapper(struct mali_session_data *session_data, _mali_uk_get_pp_core_version_s __user *uargs);
+int pp_disable_wb_wrapper(struct mali_session_data *session_data, _mali_uk_pp_disable_wb_s __user *uargs);
+int gp_start_job_wrapper(struct mali_session_data *session_data, _mali_uk_gp_start_job_s __user *uargs);
+int gp_get_number_of_cores_wrapper(struct mali_session_data *session_data, _mali_uk_get_gp_number_of_cores_s __user *uargs);
+int gp_get_core_version_wrapper(struct mali_session_data *session_data, _mali_uk_get_gp_core_version_s __user *uargs);
+int gp_suspend_response_wrapper(struct mali_session_data *session_data, _mali_uk_gp_suspend_response_s __user *uargs);
+
+int profiling_add_event_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_add_event_s __user *uargs);
+int profiling_report_sw_counters_wrapper(struct mali_session_data *session_data, _mali_uk_sw_counters_report_s __user *uargs);
+int profiling_get_stream_fd_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_stream_fd_get_s __user *uargs);
+int profiling_control_set_wrapper(struct mali_session_data *session_data, _mali_uk_profiling_control_set_s __user *uargs);
+
+int vsync_event_report_wrapper(struct mali_session_data *session_data, _mali_uk_vsync_event_report_s __user *uargs);
+
+
+int map_errcode(_mali_osk_errcode_t err);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MALI_UKK_WRAPPERS_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/platform/arm/arm.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/platform/arm/arm.c
@@ -0,0 +1,650 @@
+/*
+ * Copyright (C) 2010, 2012-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file mali_platform.c
+ * Platform specific Mali driver functions for:
+ * - Realview Versatile platforms with ARM11 Mpcore and virtex 5.
+ * - Versatile Express platforms with ARM Cortex-A9 and virtex 6.
+ */
+#include <linux/platform_device.h>
+#include <linux/version.h>
+#include <linux/pm.h>
+#include "mali_kernel_linux.h"
+#ifdef CONFIG_PM_RUNTIME
+#include <linux/pm_runtime.h>
+#endif
+#include <asm/io.h>
+#include <linux/mali/mali_utgard.h>
+#include "mali_kernel_common.h"
+#include <linux/dma-mapping.h>
+#include <linux/moduleparam.h>
+
+#include "arm_core_scaling.h"
+#include "mali_executor.h"
+
+#if defined(CONFIG_MALI_DEVFREQ) && defined(CONFIG_DEVFREQ_THERMAL)
+#include <linux/devfreq_cooling.h>
+#include <linux/thermal.h>
+#endif
+
+static int mali_core_scaling_enable = 0;
+
+void mali_gpu_utilization_callback(struct mali_gpu_utilization_data *data);
+#if !(defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP))
+static u32 mali_read_phys(u32 phys_addr);
+#endif
+#if defined(CONFIG_ARCH_REALVIEW)
+static void mali_write_phys(u32 phys_addr, u32 value);
+#endif
+
+#if defined(CONFIG_ARCH_VEXPRESS) && defined(CONFIG_ARM64)
+
+#define SECURE_MODE_CONTROL_HANDLER     0x6F02006C
+void *secure_mode_mapped_addr = NULL;
+/**
+ * Reset GPU and enable/disable Mali secure mode.
+ * @Return value:
+ * 0: success
+ * non-0: failure.
+ */
+
+static int mali_gpu_reset_and_secure_mode_enable_juno(void)
+{
+	u32 phys_offset    = SECURE_MODE_CONTROL_HANDLER & 0x00001FFF;
+	MALI_DEBUG_ASSERT(NULL != secure_mode_mapped_addr);
+
+	iowrite32(1, ((u8 *)secure_mode_mapped_addr) + phys_offset);
+
+	if (1 == (u32)ioread32(((u8 *)secure_mode_mapped_addr) + phys_offset)) {
+		MALI_DEBUG_PRINT(3, ("Mali reset GPU and enable secured mode successfully! \n"));
+		return 0;
+	}
+
+	MALI_PRINT_ERROR(("Failed to reset GPU and enable Mali secured mode !!! \n"));
+
+	return -1;
+
+}
+
+static int mali_gpu_reset_and_secure_mode_disable_juno(void)
+{
+	u32 phys_offset    = SECURE_MODE_CONTROL_HANDLER & 0x00001FFF;
+	MALI_DEBUG_ASSERT(NULL != secure_mode_mapped_addr);
+
+	iowrite32(0, ((u8 *)secure_mode_mapped_addr) + phys_offset);
+
+	if (0 == (u32)ioread32(((u8 *)secure_mode_mapped_addr) + phys_offset)) {
+		MALI_DEBUG_PRINT(3, ("Mali reset GPU and disable secured mode successfully! \n"));
+		return 0;
+	}
+
+	MALI_PRINT_ERROR(("Failed to reset GPU and disable mali secured mode !!! \n"));
+	return -1;
+}
+
+static int mali_secure_mode_init_juno(void)
+{
+	u32 phys_addr_page = SECURE_MODE_CONTROL_HANDLER & 0xFFFFE000;
+	u32 phys_offset    = SECURE_MODE_CONTROL_HANDLER & 0x00001FFF;
+	u32 map_size       = phys_offset + sizeof(u32);
+
+	MALI_DEBUG_ASSERT(NULL == secure_mode_mapped_addr);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+	secure_mode_mapped_addr = ioremap(phys_addr_page, map_size);
+#else
+	secure_mode_mapped_addr = ioremap_nocache(phys_addr_page, map_size);
+#endif
+	if (NULL != secure_mode_mapped_addr) {
+		return mali_gpu_reset_and_secure_mode_disable_juno();
+	}
+	MALI_DEBUG_PRINT(2, ("Failed to ioremap for Mali secured mode! \n"));
+	return -1;
+}
+
+static void mali_secure_mode_deinit_juno(void)
+{
+	if (NULL != secure_mode_mapped_addr) {
+		mali_gpu_reset_and_secure_mode_disable_juno();
+		iounmap(secure_mode_mapped_addr);
+		secure_mode_mapped_addr = NULL;
+	}
+}
+#endif
+
+#ifndef CONFIG_MALI_DT
+static void mali_platform_device_release(struct device *device);
+
+#if defined(CONFIG_ARCH_VEXPRESS)
+
+#if defined(CONFIG_ARM64)
+/* Juno + Mali-450 MP6 in V7 FPGA */
+static struct resource mali_gpu_resources_m450_mp6[] = {
+	MALI_GPU_RESOURCES_MALI450_MP6_PMU(0x6F040000, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200)
+};
+
+static struct resource mali_gpu_resources_m470_mp4[] = {
+	MALI_GPU_RESOURCES_MALI470_MP4_PMU(0x6F040000, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200, 200)
+};
+
+static struct resource mali_gpu_resources_m470_mp3[] = {
+	MALI_GPU_RESOURCES_MALI470_MP3_PMU(0x6F040000, 200, 200, 200, 200, 200, 200, 200, 200, 200)
+};
+
+static struct resource mali_gpu_resources_m470_mp2[] = {
+	MALI_GPU_RESOURCES_MALI470_MP2_PMU(0x6F040000, 200, 200, 200, 200, 200, 200, 200)
+};
+
+static struct resource mali_gpu_resources_m470_mp1[] = {
+	MALI_GPU_RESOURCES_MALI470_MP1_PMU(0x6F040000, 200, 200, 200, 200, 200)
+};
+
+#else
+static struct resource mali_gpu_resources_m450_mp8[] = {
+	MALI_GPU_RESOURCES_MALI450_MP8_PMU(0xFC040000, -1, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 68)
+};
+
+static struct resource mali_gpu_resources_m450_mp6[] = {
+	MALI_GPU_RESOURCES_MALI450_MP6_PMU(0xFC040000, -1, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 70, 68)
+};
+
+static struct resource mali_gpu_resources_m450_mp4[] = {
+	MALI_GPU_RESOURCES_MALI450_MP4_PMU(0xFC040000, -1, 70, 70, 70, 70, 70, 70, 70, 70, 70, 68)
+};
+
+static struct resource mali_gpu_resources_m470_mp4[] = {
+	MALI_GPU_RESOURCES_MALI470_MP4_PMU(0xFC040000, -1, 70, 70, 70, 70, 70, 70, 70, 70, 70, 68)
+};
+#endif /* CONFIG_ARM64 */
+
+#elif defined(CONFIG_ARCH_REALVIEW)
+
+static struct resource mali_gpu_resources_m300[] = {
+	MALI_GPU_RESOURCES_MALI300_PMU(0xC0000000, -1, -1, -1, -1)
+};
+
+static struct resource mali_gpu_resources_m400_mp1[] = {
+	MALI_GPU_RESOURCES_MALI400_MP1_PMU(0xC0000000, -1, -1, -1, -1)
+};
+
+static struct resource mali_gpu_resources_m400_mp2[] = {
+	MALI_GPU_RESOURCES_MALI400_MP2_PMU(0xC0000000, -1, -1, -1, -1, -1, -1)
+};
+
+#endif
+#endif
+
+#if defined(CONFIG_MALI_DEVFREQ) && defined(CONFIG_DEVFREQ_THERMAL)
+
+#define FALLBACK_STATIC_TEMPERATURE 55000
+
+static struct thermal_zone_device *gpu_tz;
+
+/* Calculate gpu static power example for reference */
+static unsigned long arm_model_static_power(unsigned long voltage)
+{
+	int temperature, temp;
+	int temp_squared, temp_cubed, temp_scaling_factor;
+	const unsigned long coefficient = (410UL << 20) / (729000000UL >> 10);
+	const unsigned long voltage_cubed = (voltage * voltage * voltage) >> 10;
+	unsigned long static_power;
+
+	if (gpu_tz) {
+		int ret;
+
+		ret = gpu_tz->ops->get_temp(gpu_tz, &temperature);
+		if (ret) {
+			MALI_DEBUG_PRINT(2, ("Error reading temperature for gpu thermal zone: %d\n", ret));
+			temperature = FALLBACK_STATIC_TEMPERATURE;
+		}
+	} else {
+		temperature = FALLBACK_STATIC_TEMPERATURE;
+	}
+
+	/* Calculate the temperature scaling factor. To be applied to the
+	 * voltage scaled power.
+	 */
+	temp = temperature / 1000;
+	temp_squared = temp * temp;
+	temp_cubed = temp_squared * temp;
+	temp_scaling_factor =
+		(2 * temp_cubed)
+		- (80 * temp_squared)
+		+ (4700 * temp)
+		+ 32000;
+
+	static_power = (((coefficient * voltage_cubed) >> 20)
+			* temp_scaling_factor)
+		       / 1000000;
+
+	return static_power;
+}
+
+/* Calculate gpu dynamic power example for reference */
+static unsigned long arm_model_dynamic_power(unsigned long freq,
+		unsigned long voltage)
+{
+	/* The inputs: freq (f) is in Hz, and voltage (v) in mV.
+	 * The coefficient (c) is in mW/(MHz mV mV).
+	 *
+	 * This function calculates the dynamic power after this formula:
+	 * Pdyn (mW) = c (mW/(MHz*mV*mV)) * v (mV) * v (mV) * f (MHz)
+	 */
+	const unsigned long v2 = (voltage * voltage) / 1000; /* m*(V*V) */
+	const unsigned long f_mhz = freq / 1000000; /* MHz */
+	const unsigned long coefficient = 3600; /* mW/(MHz*mV*mV) */
+	unsigned long dynamic_power;
+
+	dynamic_power = (coefficient * v2 * f_mhz) / 1000000; /* mW */
+
+	return dynamic_power;
+}
+
+struct devfreq_cooling_power arm_cooling_ops = {
+	.get_static_power = arm_model_static_power,
+	.get_dynamic_power = arm_model_dynamic_power,
+};
+#endif
+
+static struct mali_gpu_device_data mali_gpu_data = {
+#ifndef CONFIG_MALI_DT
+	.pmu_switch_delay = 0xFF, /* do not have to be this high on FPGA, but it is good for testing to have a delay */
+#if defined(CONFIG_ARCH_VEXPRESS)
+	.shared_mem_size = 256 * 1024 * 1024, /* 256MB */
+#endif
+#endif
+	.max_job_runtime = 60000, /* 60 seconds */
+
+#if defined(CONFIG_ARCH_REALVIEW)
+	.dedicated_mem_start = 0x80000000, /* Physical start address (use 0xD0000000 for old indirect setup) */
+	.dedicated_mem_size = 0x10000000, /* 256MB */
+#endif
+#if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP)
+	.fb_start = 0x00000000,
+	.fb_size = 0xfffff000,
+#else
+#if defined(CONFIG_ARM64)
+	/* Some framebuffer drivers get the framebuffer dynamically, such as through GEM,
+	* in which the memory resource can't be predicted in advance.
+	*/
+	.fb_start = 0x0,
+	.fb_size = 0xFFFFF000,
+#else
+	.fb_start = 0xe0000000,
+	.fb_size = 0x01000000,
+#endif
+#endif /* !defined(CONFIG_ARCH_ZYNQ) && !defined(CONFIG_ARCH_ZYNQMP) */
+	.control_interval = 1000, /* 1000ms */
+	.utilization_callback = mali_gpu_utilization_callback,
+	.get_clock_info = NULL,
+	.get_freq = NULL,
+	.set_freq = NULL,
+#if defined(CONFIG_ARCH_VEXPRESS) && defined(CONFIG_ARM64)
+	.secure_mode_init = mali_secure_mode_init_juno,
+	.secure_mode_deinit = mali_secure_mode_deinit_juno,
+	.gpu_reset_and_secure_mode_enable = mali_gpu_reset_and_secure_mode_enable_juno,
+	.gpu_reset_and_secure_mode_disable = mali_gpu_reset_and_secure_mode_disable_juno,
+#else
+	.secure_mode_init = NULL,
+	.secure_mode_deinit = NULL,
+	.gpu_reset_and_secure_mode_enable = NULL,
+	.gpu_reset_and_secure_mode_disable = NULL,
+#endif
+#if defined(CONFIG_MALI_DEVFREQ) && defined(CONFIG_DEVFREQ_THERMAL)
+	.gpu_cooling_ops = &arm_cooling_ops,
+#endif
+};
+
+#ifndef CONFIG_MALI_DT
+static struct platform_device mali_gpu_device = {
+	.name = MALI_GPU_NAME_UTGARD,
+	.id = 0,
+	.dev.release = mali_platform_device_release,
+	.dev.dma_mask = &mali_gpu_device.dev.coherent_dma_mask,
+	.dev.coherent_dma_mask = DMA_BIT_MASK(32),
+
+	.dev.platform_data = &mali_gpu_data,
+};
+
+int mali_platform_device_register(void)
+{
+	int err = -1;
+	int num_pp_cores = 0;
+#if defined(CONFIG_ARCH_REALVIEW)
+	u32 m400_gp_version;
+#endif
+
+	MALI_DEBUG_PRINT(4, ("mali_platform_device_register() called\n"));
+
+	/* Detect present Mali GPU and connect the correct resources to the device */
+#if defined(CONFIG_ARCH_VEXPRESS)
+
+#if defined(CONFIG_ARM64)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 4, 0)
+	mali_gpu_device.dev.archdata.dma_ops = &dummy_dma_ops;
+#else
+	mali_gpu_device.dev.archdata.dma_ops = dma_ops;
+#endif
+	if ((mali_read_phys(0x6F000000) & 0x00600450) == 0x00600450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP6 device\n"));
+		num_pp_cores = 6;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m450_mp6);
+		mali_gpu_device.resource = mali_gpu_resources_m450_mp6;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00400430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP4 device\n"));
+		num_pp_cores = 4;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m470_mp4);
+		mali_gpu_device.resource = mali_gpu_resources_m470_mp4;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00300430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP3 device\n"));
+		num_pp_cores = 3;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m470_mp3);
+		mali_gpu_device.resource = mali_gpu_resources_m470_mp3;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00200430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP2 device\n"));
+		num_pp_cores = 2;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m470_mp2);
+		mali_gpu_device.resource = mali_gpu_resources_m470_mp2;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00100430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP1 device\n"));
+		num_pp_cores = 1;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m470_mp1);
+		mali_gpu_device.resource = mali_gpu_resources_m470_mp1;
+	}
+#else
+	if (mali_read_phys(0xFC000000) == 0x00000450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP8 device\n"));
+		num_pp_cores = 8;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m450_mp8);
+		mali_gpu_device.resource = mali_gpu_resources_m450_mp8;
+	} else if (mali_read_phys(0xFC000000) == 0x40600450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP6 device\n"));
+		num_pp_cores = 6;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m450_mp6);
+		mali_gpu_device.resource = mali_gpu_resources_m450_mp6;
+	} else if (mali_read_phys(0xFC000000) == 0x40400450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP4 device\n"));
+		num_pp_cores = 4;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m450_mp4);
+		mali_gpu_device.resource = mali_gpu_resources_m450_mp4;
+	} else if (mali_read_phys(0xFC000000) == 0xFFFFFFFF) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP4 device\n"));
+		num_pp_cores = 4;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m470_mp4);
+		mali_gpu_device.resource = mali_gpu_resources_m470_mp4;
+	}
+#endif /* CONFIG_ARM64 */
+
+#elif defined(CONFIG_ARCH_REALVIEW)
+
+	m400_gp_version = mali_read_phys(0xC000006C);
+	if ((m400_gp_version & 0xFFFF0000) == 0x0C070000) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-300 device\n"));
+		num_pp_cores = 1;
+		mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m300);
+		mali_gpu_device.resource = mali_gpu_resources_m300;
+		mali_write_phys(0xC0010020, 0xA); /* Enable direct memory mapping for FPGA */
+	} else if ((m400_gp_version & 0xFFFF0000) == 0x0B070000) {
+		u32 fpga_fw_version = mali_read_phys(0xC0010000);
+		if (fpga_fw_version == 0x130C008F || fpga_fw_version == 0x110C008F) {
+			/* Mali-400 MP1 r1p0 or r1p1 */
+			MALI_DEBUG_PRINT(4, ("Registering Mali-400 MP1 device\n"));
+			num_pp_cores = 1;
+			mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m400_mp1);
+			mali_gpu_device.resource = mali_gpu_resources_m400_mp1;
+			mali_write_phys(0xC0010020, 0xA); /* Enable direct memory mapping for FPGA */
+		} else if (fpga_fw_version == 0x130C000F) {
+			/* Mali-400 MP2 r1p1 */
+			MALI_DEBUG_PRINT(4, ("Registering Mali-400 MP2 device\n"));
+			num_pp_cores = 2;
+			mali_gpu_device.num_resources = ARRAY_SIZE(mali_gpu_resources_m400_mp2);
+			mali_gpu_device.resource = mali_gpu_resources_m400_mp2;
+			mali_write_phys(0xC0010020, 0xA); /* Enable direct memory mapping for FPGA */
+		}
+	}
+
+#endif
+	/* Register the platform device */
+	err = platform_device_register(&mali_gpu_device);
+	if (0 == err) {
+#ifdef CONFIG_PM_RUNTIME
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 37))
+		pm_runtime_set_autosuspend_delay(&(mali_gpu_device.dev), 1000);
+		pm_runtime_use_autosuspend(&(mali_gpu_device.dev));
+#endif
+		pm_runtime_enable(&(mali_gpu_device.dev));
+#endif
+		MALI_DEBUG_ASSERT(0 < num_pp_cores);
+		mali_core_scaling_init(num_pp_cores);
+
+		return 0;
+	}
+
+	return err;
+}
+
+void mali_platform_device_unregister(void)
+{
+	MALI_DEBUG_PRINT(4, ("mali_platform_device_unregister() called\n"));
+
+	mali_core_scaling_term();
+#ifdef CONFIG_PM_RUNTIME
+	pm_runtime_disable(&(mali_gpu_device.dev));
+#endif
+	platform_device_unregister(&mali_gpu_device);
+
+	platform_device_put(&mali_gpu_device);
+
+#if defined(CONFIG_ARCH_REALVIEW)
+	mali_write_phys(0xC0010020, 0x9); /* Restore default (legacy) memory mapping */
+#endif
+}
+
+static void mali_platform_device_release(struct device *device)
+{
+	MALI_DEBUG_PRINT(4, ("mali_platform_device_release() called\n"));
+}
+
+#else /* CONFIG_MALI_DT */
+int mali_platform_device_init(struct platform_device *device)
+{
+	int num_pp_cores = 0;
+	int err = -1;
+#if defined(CONFIG_ARCH_REALVIEW)
+	u32 m400_gp_version;
+#endif
+
+	/* Detect present Mali GPU and connect the correct resources to the device */
+#if defined(CONFIG_ARCH_VEXPRESS)
+
+#if defined(CONFIG_ARM64)
+	if ((mali_read_phys(0x6F000000) & 0x00600450) == 0x00600450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP6 device\n"));
+		num_pp_cores = 6;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00400430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP4 device\n"));
+		num_pp_cores = 4;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00300430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP3 device\n"));
+		num_pp_cores = 3;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00200430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP2 device\n"));
+		num_pp_cores = 2;
+	} else if ((mali_read_phys(0x6F000000) & 0x00F00430) == 0x00100430) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP1 device\n"));
+		num_pp_cores = 1;
+	}
+#else
+	if (mali_read_phys(0xFC000000) == 0x00000450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP8 device\n"));
+		num_pp_cores = 8;
+	} else if (mali_read_phys(0xFC000000) == 0x40400450) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-450 MP4 device\n"));
+		num_pp_cores = 4;
+	} else if (mali_read_phys(0xFC000000) == 0xFFFFFFFF) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-470 MP4 device\n"));
+		num_pp_cores = 4;
+	}
+#endif
+
+#elif defined(CONFIG_ARCH_REALVIEW)
+
+	m400_gp_version = mali_read_phys(0xC000006C);
+	if ((m400_gp_version & 0xFFFF0000) == 0x0C070000) {
+		MALI_DEBUG_PRINT(4, ("Registering Mali-300 device\n"));
+		num_pp_cores = 1;
+		mali_write_phys(0xC0010020, 0xA); /* Enable direct memory mapping for FPGA */
+	} else if ((m400_gp_version & 0xFFFF0000) == 0x0B070000) {
+		u32 fpga_fw_version = mali_read_phys(0xC0010000);
+		if (fpga_fw_version == 0x130C008F || fpga_fw_version == 0x110C008F) {
+			/* Mali-400 MP1 r1p0 or r1p1 */
+			MALI_DEBUG_PRINT(4, ("Registering Mali-400 MP1 device\n"));
+			num_pp_cores = 1;
+			mali_write_phys(0xC0010020, 0xA); /* Enable direct memory mapping for FPGA */
+		} else if (fpga_fw_version == 0x130C000F) {
+			/* Mali-400 MP2 r1p1 */
+			MALI_DEBUG_PRINT(4, ("Registering Mali-400 MP2 device\n"));
+			num_pp_cores = 2;
+			mali_write_phys(0xC0010020, 0xA); /* Enable direct memory mapping for FPGA */
+		}
+	}
+#elif defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP)
+
+	MALI_DEBUG_PRINT(4, ("Registering Zynq/ZynqMP Mali-400 device\n"));
+	num_pp_cores = 2;
+
+#endif
+
+	/* After kernel 3.15 device tree will default set dev
+	 * related parameters in of_platform_device_create_pdata.
+	 * But kernel changes from version to version,
+	 * For example 3.10 didn't include device->dev.dma_mask parameter setting,
+	 * if we didn't include here will cause dma_mapping error,
+	 * but in kernel 3.15 it include  device->dev.dma_mask parameter setting,
+	 * so it's better to set must need paramter by DDK itself.
+	 */
+	if (!device->dev.dma_mask)
+		device->dev.dma_mask = &device->dev.coherent_dma_mask;
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 8, 0))
+	device->dev.archdata.dma_ops = dma_ops;
+#endif
+	err = platform_device_add_data(device, &mali_gpu_data, sizeof(mali_gpu_data));
+
+	if (0 == err) {
+#ifdef CONFIG_PM_RUNTIME
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 37))
+		pm_runtime_set_autosuspend_delay(&(device->dev), 1000);
+		pm_runtime_use_autosuspend(&(device->dev));
+#endif
+		pm_runtime_enable(&(device->dev));
+#endif
+		MALI_DEBUG_ASSERT(0 < num_pp_cores);
+		mali_core_scaling_init(num_pp_cores);
+	}
+
+#if defined(CONFIG_MALI_DEVFREQ) && defined(CONFIG_DEVFREQ_THERMAL)
+	/* Get thermal zone */
+	gpu_tz = thermal_zone_get_zone_by_name("soc_thermal");
+	if (IS_ERR(gpu_tz)) {
+		MALI_DEBUG_PRINT(2, ("Error getting gpu thermal zone (%ld), not yet ready?\n",
+				     PTR_ERR(gpu_tz)));
+		gpu_tz = NULL;
+
+		err =  -EPROBE_DEFER;
+	}
+#endif
+
+	return err;
+}
+
+int mali_platform_device_deinit(struct platform_device *device)
+{
+	MALI_IGNORE(device);
+
+	MALI_DEBUG_PRINT(4, ("mali_platform_device_deinit() called\n"));
+
+	mali_core_scaling_term();
+#ifdef CONFIG_PM_RUNTIME
+	pm_runtime_disable(&(device->dev));
+#endif
+
+#if defined(CONFIG_ARCH_REALVIEW)
+	mali_write_phys(0xC0010020, 0x9); /* Restore default (legacy) memory mapping */
+#endif
+
+	return 0;
+}
+
+#endif /* CONFIG_MALI_DT */
+
+#if !(defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP))
+static u32 mali_read_phys(u32 phys_addr)
+{
+	u32 phys_addr_page = phys_addr & 0xFFFFE000;
+	u32 phys_offset    = phys_addr & 0x00001FFF;
+	u32 map_size       = phys_offset + sizeof(u32);
+	u32 ret = 0xDEADBEEF;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+	void *mem_mapped = ioremap(phys_addr_page, map_size);
+#else
+	void *mem_mapped = ioremap_nocache(phys_addr_page, map_size);
+#endif
+	if (NULL != mem_mapped) {
+		ret = (u32)ioread32(((u8 *)mem_mapped) + phys_offset);
+		iounmap(mem_mapped);
+	}
+
+	return ret;
+}
+#endif
+
+#if defined(CONFIG_ARCH_REALVIEW)
+static void mali_write_phys(u32 phys_addr, u32 value)
+{
+	u32 phys_addr_page = phys_addr & 0xFFFFE000;
+	u32 phys_offset    = phys_addr & 0x00001FFF;
+	u32 map_size       = phys_offset + sizeof(u32);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+	void *mem_mapped = ioremap(phys_addr_page, map_size);
+#else
+	void *mem_mapped = ioremap_nocache(phys_addr_page, map_size);
+#endif
+	if (NULL != mem_mapped) {
+		iowrite32(value, ((u8 *)mem_mapped) + phys_offset);
+		iounmap(mem_mapped);
+	}
+}
+#endif
+
+static int param_set_core_scaling(const char *val, const struct kernel_param *kp)
+{
+	int ret = param_set_int(val, kp);
+
+	if (1 == mali_core_scaling_enable) {
+		mali_core_scaling_sync(mali_executor_get_num_cores_enabled());
+	}
+	return ret;
+}
+
+static struct kernel_param_ops param_ops_core_scaling = {
+	.set = param_set_core_scaling,
+	.get = param_get_int,
+};
+
+module_param_cb(mali_core_scaling_enable, &param_ops_core_scaling, &mali_core_scaling_enable, 0644);
+MODULE_PARM_DESC(mali_core_scaling_enable, "1 means to enable core scaling policy, 0 means to disable core scaling policy");
+
+void mali_gpu_utilization_callback(struct mali_gpu_utilization_data *data)
+{
+	if (1 == mali_core_scaling_enable) {
+		mali_core_scaling_update(data);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/platform/arm/arm_core_scaling.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/platform/arm/arm_core_scaling.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file arm_core_scaling.c
+ * Example core scaling policy.
+ */
+
+#include "arm_core_scaling.h"
+
+#include <linux/mali/mali_utgard.h>
+#include "mali_kernel_common.h"
+
+#include <linux/workqueue.h>
+
+static int num_cores_total;
+static int num_cores_enabled;
+
+static struct work_struct wq_work;
+
+static void set_num_cores(struct work_struct *work)
+{
+	int err = mali_perf_set_num_pp_cores(num_cores_enabled);
+	MALI_DEBUG_ASSERT(0 == err);
+	MALI_IGNORE(err);
+}
+
+static void enable_one_core(void)
+{
+	if (num_cores_enabled < num_cores_total) {
+		++num_cores_enabled;
+		schedule_work(&wq_work);
+		MALI_DEBUG_PRINT(3, ("Core scaling: Enabling one more core\n"));
+	}
+
+	MALI_DEBUG_ASSERT(1 <= num_cores_enabled);
+	MALI_DEBUG_ASSERT(num_cores_total >= num_cores_enabled);
+}
+
+static void disable_one_core(void)
+{
+	if (1 < num_cores_enabled) {
+		--num_cores_enabled;
+		schedule_work(&wq_work);
+		MALI_DEBUG_PRINT(3, ("Core scaling: Disabling one core\n"));
+	}
+
+	MALI_DEBUG_ASSERT(1 <= num_cores_enabled);
+	MALI_DEBUG_ASSERT(num_cores_total >= num_cores_enabled);
+}
+
+static void enable_max_num_cores(void)
+{
+	if (num_cores_enabled < num_cores_total) {
+		num_cores_enabled = num_cores_total;
+		schedule_work(&wq_work);
+		MALI_DEBUG_PRINT(3, ("Core scaling: Enabling maximum number of cores\n"));
+	}
+
+	MALI_DEBUG_ASSERT(num_cores_total == num_cores_enabled);
+}
+
+void mali_core_scaling_init(int num_pp_cores)
+{
+	INIT_WORK(&wq_work, set_num_cores);
+
+	num_cores_total   = num_pp_cores;
+	num_cores_enabled = num_pp_cores;
+
+	/* NOTE: Mali is not fully initialized at this point. */
+}
+
+void mali_core_scaling_sync(int num_cores)
+{
+	num_cores_enabled = num_cores;
+}
+
+void mali_core_scaling_term(void)
+{
+	flush_scheduled_work();
+}
+
+#define PERCENT_OF(percent, max) ((int) ((percent)*(max)/100.0 + 0.5))
+
+void mali_core_scaling_update(struct mali_gpu_utilization_data *data)
+{
+	/*
+	 * This function implements a very trivial PP core scaling algorithm.
+	 *
+	 * It is _NOT_ of production quality.
+	 * The only intention behind this algorithm is to exercise and test the
+	 * core scaling functionality of the driver.
+	 * It is _NOT_ tuned for neither power saving nor performance!
+	 *
+	 * Other metrics than PP utilization need to be considered as well
+	 * in order to make a good core scaling algorithm.
+	 */
+
+	MALI_DEBUG_PRINT(3, ("Utilization: (%3d, %3d, %3d), cores enabled: %d/%d\n", data->utilization_gpu, data->utilization_gp, data->utilization_pp, num_cores_enabled, num_cores_total));
+
+	/* NOTE: this function is normally called directly from the utilization callback which is in
+	 * timer context. */
+
+	if (PERCENT_OF(90, 256) < data->utilization_pp) {
+		enable_max_num_cores();
+	} else if (PERCENT_OF(50, 256) < data->utilization_pp) {
+		enable_one_core();
+	} else if (PERCENT_OF(40, 256) < data->utilization_pp) {
+		/* do nothing */
+	} else if (PERCENT_OF(0, 256) < data->utilization_pp) {
+		disable_one_core();
+	} else {
+		/* do nothing */
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/platform/arm/arm_core_scaling.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/platform/arm/arm_core_scaling.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file arm_core_scaling.h
+ * Example core scaling policy.
+ */
+
+#ifndef __ARM_CORE_SCALING_H__
+#define __ARM_CORE_SCALING_H__
+
+struct mali_gpu_utilization_data;
+
+/**
+ * Initialize core scaling policy.
+ *
+ * @note The core scaling policy will assume that all PP cores are on initially.
+ *
+ * @param num_pp_cores Total number of PP cores.
+ */
+void mali_core_scaling_init(int num_pp_cores);
+
+/**
+ * Terminate core scaling policy.
+ */
+void mali_core_scaling_term(void);
+
+/**
+ * Update core scaling policy with new utilization data.
+ *
+ * @param data Utilization data.
+ */
+void mali_core_scaling_update(struct mali_gpu_utilization_data *data);
+
+void mali_core_scaling_sync(int num_cores);
+
+#endif /* __ARM_CORE_SCALING_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/platform/arm/juno_opp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/platform/arm/juno_opp.c
@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2010, 2012-2016, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+/**
+ * @file juno_opp.c
+ * Example: Set up opp table
+ * Using ARM64 juno specific SCPI_PROTOCOL get frequence inform
+ * Customer need implement your own platform releated logic
+ */
+#ifdef CONFIG_ARCH_VEXPRESS
+#ifdef CONFIG_MALI_DEVFREQ
+#ifdef CONFIG_ARM64
+#ifdef CONFIG_ARM_SCPI_PROTOCOL
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/scpi_protocol.h>
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 13, 0)
+#include <linux/pm_opp.h>
+#else /* Linux >= 3.13 */
+/* In 3.13 the OPP include header file, types, and functions were all
+ * renamed. Use the old filename for the include, and define the new names to
+ * the old, when an old kernel is detected.
+ */
+#include <linux/opp.h>
+#define dev_pm_opp_add opp_add
+#define dev_pm_opp_remove opp_remove
+#endif /* Linux >= 3.13 */
+
+#include "mali_kernel_common.h"
+
+static int init_juno_opps_from_scpi(struct device *dev)
+{
+	struct scpi_dvfs_info *sinfo;
+	struct scpi_ops *sops;
+
+	int i;
+
+	sops = get_scpi_ops();
+	if (NULL == sops) {
+		MALI_DEBUG_PRINT(2, ("Mali didn't get any scpi ops \n"));
+		return -1;
+	}
+
+	/* Hard coded for Juno. 2 is GPU domain */
+	sinfo = sops->dvfs_get_info(2);
+	if (IS_ERR_OR_NULL(sinfo))
+		return PTR_ERR(sinfo);
+
+	for (i = 0; i < sinfo->count; i++) {
+		struct scpi_opp *e = &sinfo->opps[i];
+
+		MALI_DEBUG_PRINT(2, ("Mali OPP from SCPI: %u Hz @ %u mV\n", e->freq, e->m_volt));
+
+		dev_pm_opp_add(dev, e->freq, e->m_volt * 1000);
+	}
+
+	return 0;
+}
+
+int setup_opps(void)
+{
+	struct device_node *np;
+	struct platform_device *pdev;
+	int err;
+
+	np = of_find_node_by_name(NULL, "gpu");
+	if (!np) {
+		pr_err("Failed to find DT entry for Mali\n");
+		return -EFAULT;
+	}
+
+	pdev = of_find_device_by_node(np);
+	if (!pdev) {
+		pr_err("Failed to find device for Mali\n");
+		of_node_put(np);
+		return -EFAULT;
+	}
+
+	err = init_juno_opps_from_scpi(&pdev->dev);
+
+	of_node_put(np);
+
+	return err;
+}
+
+int term_opps(struct device *dev)
+{
+	struct scpi_dvfs_info *sinfo;
+	struct scpi_ops *sops;
+
+	int i;
+
+	sops = get_scpi_ops();
+	if (NULL == sops) {
+		MALI_DEBUG_PRINT(2, ("Mali didn't get any scpi ops \n"));
+		return -1;
+	}
+
+	/* Hard coded for Juno. 2 is GPU domain */
+	sinfo = sops->dvfs_get_info(2);
+	if (IS_ERR_OR_NULL(sinfo))
+		return PTR_ERR(sinfo);
+
+	for (i = 0; i < sinfo->count; i++) {
+		struct scpi_opp *e = &sinfo->opps[i];
+
+		MALI_DEBUG_PRINT(2, ("Mali Remove OPP: %u Hz \n", e->freq));
+
+		dev_pm_opp_remove(dev, e->freq);
+	}
+
+	return 0;
+
+}
+#endif
+#endif
+#endif
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/readme.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/readme.txt
@@ -0,0 +1,28 @@
+Building the Mali Device Driver for Linux
+-----------------------------------------
+
+Build the Mali Device Driver for Linux by running the following make command:
+
+KDIR=<kdir_path> USING_UMP=<ump_option> BUILD=<build_option> make
+
+where
+    kdir_path: Path to your Linux Kernel directory
+    ump_option: 1 = Enable UMP support(*)
+                0 = disable UMP support
+    build_option: debug = debug build of driver
+                  release = release build of driver
+
+(*)  For newer Linux Kernels, the Module.symvers file for the UMP device driver
+     must be available. The UMP_SYMVERS_FILE variable in the Makefile should
+     point to this file. This file is generated when the UMP driver is built.
+
+The result will be a mali.ko file, which can be loaded into the Linux kernel
+by using the insmod command.
+
+Use of UMP is not recommended. The dma-buf API in the Linux kernel has
+replaced UMP. The Mali Device Driver will be built with dma-buf support if the
+kernel config includes enabled dma-buf.
+
+The kernel needs to be provided with a platform_device struct for the Mali GPU
+device. See the mali_utgard.h header file for how to set up the Mali GPU
+resources.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/regs/mali_200_regs.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/regs/mali_200_regs.h
@@ -0,0 +1,131 @@
+/*
+ * Copyright (C) 2010, 2012-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef _MALI200_REGS_H_
+#define _MALI200_REGS_H_
+
+/**
+ *  Enum for management register addresses.
+ */
+enum mali200_mgmt_reg {
+	MALI200_REG_ADDR_MGMT_VERSION                              = 0x1000,
+	MALI200_REG_ADDR_MGMT_CURRENT_REND_LIST_ADDR               = 0x1004,
+	MALI200_REG_ADDR_MGMT_STATUS                               = 0x1008,
+	MALI200_REG_ADDR_MGMT_CTRL_MGMT                            = 0x100c,
+
+	MALI200_REG_ADDR_MGMT_INT_RAWSTAT                          = 0x1020,
+	MALI200_REG_ADDR_MGMT_INT_CLEAR                            = 0x1024,
+	MALI200_REG_ADDR_MGMT_INT_MASK                             = 0x1028,
+	MALI200_REG_ADDR_MGMT_INT_STATUS                           = 0x102c,
+
+	MALI200_REG_ADDR_MGMT_BUS_ERROR_STATUS                     = 0x1050,
+
+	MALI200_REG_ADDR_MGMT_PERF_CNT_0_ENABLE                    = 0x1080,
+	MALI200_REG_ADDR_MGMT_PERF_CNT_0_SRC                       = 0x1084,
+	MALI200_REG_ADDR_MGMT_PERF_CNT_0_LIMIT                     = 0x1088,
+	MALI200_REG_ADDR_MGMT_PERF_CNT_0_VALUE                     = 0x108c,
+
+	MALI200_REG_ADDR_MGMT_PERF_CNT_1_ENABLE                    = 0x10a0,
+	MALI200_REG_ADDR_MGMT_PERF_CNT_1_SRC                       = 0x10a4,
+	MALI200_REG_ADDR_MGMT_PERF_CNT_1_VALUE                     = 0x10ac,
+
+	MALI200_REG_ADDR_MGMT_PERFMON_CONTR                        = 0x10b0,
+	MALI200_REG_ADDR_MGMT_PERFMON_BASE                         = 0x10b4,
+
+	MALI200_REG_SIZEOF_REGISTER_BANK                           = 0x10f0
+
+};
+
+#define MALI200_REG_VAL_PERF_CNT_ENABLE 1
+
+enum mali200_mgmt_ctrl_mgmt {
+	MALI200_REG_VAL_CTRL_MGMT_STOP_BUS         = (1 << 0),
+	MALI200_REG_VAL_CTRL_MGMT_FLUSH_CACHES     = (1 << 3),
+	MALI200_REG_VAL_CTRL_MGMT_FORCE_RESET      = (1 << 5),
+	MALI200_REG_VAL_CTRL_MGMT_START_RENDERING  = (1 << 6),
+	MALI400PP_REG_VAL_CTRL_MGMT_SOFT_RESET     = (1 << 7), /* Only valid for Mali-300 and later */
+};
+
+enum mali200_mgmt_irq {
+	MALI200_REG_VAL_IRQ_END_OF_FRAME          = (1 << 0),
+	MALI200_REG_VAL_IRQ_END_OF_TILE           = (1 << 1),
+	MALI200_REG_VAL_IRQ_HANG                  = (1 << 2),
+	MALI200_REG_VAL_IRQ_FORCE_HANG            = (1 << 3),
+	MALI200_REG_VAL_IRQ_BUS_ERROR             = (1 << 4),
+	MALI200_REG_VAL_IRQ_BUS_STOP              = (1 << 5),
+	MALI200_REG_VAL_IRQ_CNT_0_LIMIT           = (1 << 6),
+	MALI200_REG_VAL_IRQ_CNT_1_LIMIT           = (1 << 7),
+	MALI200_REG_VAL_IRQ_WRITE_BOUNDARY_ERROR  = (1 << 8),
+	MALI400PP_REG_VAL_IRQ_INVALID_PLIST_COMMAND = (1 << 9),
+	MALI400PP_REG_VAL_IRQ_CALL_STACK_UNDERFLOW  = (1 << 10),
+	MALI400PP_REG_VAL_IRQ_CALL_STACK_OVERFLOW   = (1 << 11),
+	MALI400PP_REG_VAL_IRQ_RESET_COMPLETED       = (1 << 12),
+};
+
+#define MALI200_REG_VAL_IRQ_MASK_ALL  ((enum mali200_mgmt_irq) (\
+				       MALI200_REG_VAL_IRQ_END_OF_FRAME                           |\
+				       MALI200_REG_VAL_IRQ_END_OF_TILE                            |\
+				       MALI200_REG_VAL_IRQ_HANG                                   |\
+				       MALI200_REG_VAL_IRQ_FORCE_HANG                             |\
+				       MALI200_REG_VAL_IRQ_BUS_ERROR                              |\
+				       MALI200_REG_VAL_IRQ_BUS_STOP                               |\
+				       MALI200_REG_VAL_IRQ_CNT_0_LIMIT                            |\
+				       MALI200_REG_VAL_IRQ_CNT_1_LIMIT                            |\
+				       MALI200_REG_VAL_IRQ_WRITE_BOUNDARY_ERROR                   |\
+				       MALI400PP_REG_VAL_IRQ_INVALID_PLIST_COMMAND                  |\
+				       MALI400PP_REG_VAL_IRQ_CALL_STACK_UNDERFLOW                   |\
+				       MALI400PP_REG_VAL_IRQ_CALL_STACK_OVERFLOW                    |\
+				       MALI400PP_REG_VAL_IRQ_RESET_COMPLETED))
+
+#define MALI200_REG_VAL_IRQ_MASK_USED ((enum mali200_mgmt_irq) (\
+				       MALI200_REG_VAL_IRQ_END_OF_FRAME                           |\
+				       MALI200_REG_VAL_IRQ_FORCE_HANG                             |\
+				       MALI200_REG_VAL_IRQ_BUS_ERROR                              |\
+				       MALI200_REG_VAL_IRQ_WRITE_BOUNDARY_ERROR                   |\
+				       MALI400PP_REG_VAL_IRQ_INVALID_PLIST_COMMAND                  |\
+				       MALI400PP_REG_VAL_IRQ_CALL_STACK_UNDERFLOW                   |\
+				       MALI400PP_REG_VAL_IRQ_CALL_STACK_OVERFLOW))
+
+#define MALI200_REG_VAL_IRQ_MASK_NONE ((enum mali200_mgmt_irq)(0))
+
+enum mali200_mgmt_status {
+	MALI200_REG_VAL_STATUS_RENDERING_ACTIVE     = (1 << 0),
+	MALI200_REG_VAL_STATUS_BUS_STOPPED          = (1 << 4),
+};
+
+enum mali200_render_unit {
+	MALI200_REG_ADDR_FRAME = 0x0000,
+	MALI200_REG_ADDR_RSW   = 0x0004,
+	MALI200_REG_ADDR_STACK = 0x0030,
+	MALI200_REG_ADDR_STACK_SIZE = 0x0034,
+	MALI200_REG_ADDR_ORIGIN_OFFSET_X  = 0x0040
+};
+
+enum mali200_wb_unit {
+	MALI200_REG_ADDR_WB0 = 0x0100,
+	MALI200_REG_ADDR_WB1 = 0x0200,
+	MALI200_REG_ADDR_WB2 = 0x0300
+};
+
+enum mali200_wb_unit_regs {
+	MALI200_REG_ADDR_WB_SOURCE_SELECT = 0x0000,
+	MALI200_REG_ADDR_WB_SOURCE_ADDR   = 0x0004,
+};
+
+/* This should be in the top 16 bit of the version register of Mali PP */
+#define MALI200_PP_PRODUCT_ID 0xC807
+#define MALI300_PP_PRODUCT_ID 0xCE07
+#define MALI400_PP_PRODUCT_ID 0xCD07
+#define MALI450_PP_PRODUCT_ID 0xCF07
+#define MALI470_PP_PRODUCT_ID 0xCF08
+
+
+
+#endif /* _MALI200_REGS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/regs/mali_gp_regs.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/regs/mali_gp_regs.h
@@ -0,0 +1,172 @@
+/*
+ * Copyright (C) 2010, 2012-2015, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef _MALIGP2_CONROL_REGS_H_
+#define _MALIGP2_CONROL_REGS_H_
+
+/**
+ * These are the different geometry processor control registers.
+ * Their usage is to control and monitor the operation of the
+ * Vertex Shader and the Polygon List Builder in the geometry processor.
+ * Addresses are in 32-bit word relative sizes.
+ * @see [P0081] "Geometry Processor Data Structures" for details
+ */
+
+typedef enum {
+	MALIGP2_REG_ADDR_MGMT_VSCL_START_ADDR           = 0x00,
+	MALIGP2_REG_ADDR_MGMT_VSCL_END_ADDR             = 0x04,
+	MALIGP2_REG_ADDR_MGMT_PLBUCL_START_ADDR         = 0x08,
+	MALIGP2_REG_ADDR_MGMT_PLBUCL_END_ADDR           = 0x0c,
+	MALIGP2_REG_ADDR_MGMT_PLBU_ALLOC_START_ADDR     = 0x10,
+	MALIGP2_REG_ADDR_MGMT_PLBU_ALLOC_END_ADDR       = 0x14,
+	MALIGP2_REG_ADDR_MGMT_CMD                       = 0x20,
+	MALIGP2_REG_ADDR_MGMT_INT_RAWSTAT               = 0x24,
+	MALIGP2_REG_ADDR_MGMT_INT_CLEAR                 = 0x28,
+	MALIGP2_REG_ADDR_MGMT_INT_MASK                  = 0x2C,
+	MALIGP2_REG_ADDR_MGMT_INT_STAT                  = 0x30,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_ENABLE         = 0x3C,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_1_ENABLE         = 0x40,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_SRC            = 0x44,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_1_SRC            = 0x48,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_VALUE          = 0x4C,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_1_VALUE          = 0x50,
+	MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_LIMIT          = 0x54,
+	MALIGP2_REG_ADDR_MGMT_STATUS                    = 0x68,
+	MALIGP2_REG_ADDR_MGMT_VERSION                   = 0x6C,
+	MALIGP2_REG_ADDR_MGMT_VSCL_START_ADDR_READ      = 0x80,
+	MALIGP2_REG_ADDR_MGMT_PLBCL_START_ADDR_READ     = 0x84,
+	MALIGP2_CONTR_AXI_BUS_ERROR_STAT                = 0x94,
+	MALIGP2_REGISTER_ADDRESS_SPACE_SIZE             = 0x98,
+} maligp_reg_addr_mgmt_addr;
+
+#define MALIGP2_REG_VAL_PERF_CNT_ENABLE 1
+
+/**
+ * Commands to geometry processor.
+ *  @see MALIGP2_CTRL_REG_CMD
+ */
+typedef enum {
+	MALIGP2_REG_VAL_CMD_START_VS                    = (1 << 0),
+	MALIGP2_REG_VAL_CMD_START_PLBU                  = (1 << 1),
+	MALIGP2_REG_VAL_CMD_UPDATE_PLBU_ALLOC   = (1 << 4),
+	MALIGP2_REG_VAL_CMD_RESET                               = (1 << 5),
+	MALIGP2_REG_VAL_CMD_FORCE_HANG                  = (1 << 6),
+	MALIGP2_REG_VAL_CMD_STOP_BUS                    = (1 << 9),
+	MALI400GP_REG_VAL_CMD_SOFT_RESET                = (1 << 10), /* only valid for Mali-300 and later */
+} mgp_contr_reg_val_cmd;
+
+
+/**  @defgroup MALIGP2_IRQ
+ * Interrupt status of geometry processor.
+ *  @see MALIGP2_CTRL_REG_INT_RAWSTAT, MALIGP2_REG_ADDR_MGMT_INT_CLEAR,
+ *       MALIGP2_REG_ADDR_MGMT_INT_MASK, MALIGP2_REG_ADDR_MGMT_INT_STAT
+ * @{
+ */
+#define MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST      (1 << 0)
+#define MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST    (1 << 1)
+#define MALIGP2_REG_VAL_IRQ_PLBU_OUT_OF_MEM     (1 << 2)
+#define MALIGP2_REG_VAL_IRQ_VS_SEM_IRQ          (1 << 3)
+#define MALIGP2_REG_VAL_IRQ_PLBU_SEM_IRQ        (1 << 4)
+#define MALIGP2_REG_VAL_IRQ_HANG                (1 << 5)
+#define MALIGP2_REG_VAL_IRQ_FORCE_HANG          (1 << 6)
+#define MALIGP2_REG_VAL_IRQ_PERF_CNT_0_LIMIT    (1 << 7)
+#define MALIGP2_REG_VAL_IRQ_PERF_CNT_1_LIMIT    (1 << 8)
+#define MALIGP2_REG_VAL_IRQ_WRITE_BOUND_ERR     (1 << 9)
+#define MALIGP2_REG_VAL_IRQ_SYNC_ERROR          (1 << 10)
+#define MALIGP2_REG_VAL_IRQ_AXI_BUS_ERROR       (1 << 11)
+#define MALI400GP_REG_VAL_IRQ_AXI_BUS_STOPPED     (1 << 12)
+#define MALI400GP_REG_VAL_IRQ_VS_INVALID_CMD      (1 << 13)
+#define MALI400GP_REG_VAL_IRQ_PLB_INVALID_CMD     (1 << 14)
+#define MALI400GP_REG_VAL_IRQ_RESET_COMPLETED     (1 << 19)
+#define MALI400GP_REG_VAL_IRQ_SEMAPHORE_UNDERFLOW (1 << 20)
+#define MALI400GP_REG_VAL_IRQ_SEMAPHORE_OVERFLOW  (1 << 21)
+#define MALI400GP_REG_VAL_IRQ_PTR_ARRAY_OUT_OF_BOUNDS  (1 << 22)
+
+/* Mask defining all IRQs in Mali GP */
+#define MALIGP2_REG_VAL_IRQ_MASK_ALL \
+	(\
+	 MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST      | \
+	 MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST    | \
+	 MALIGP2_REG_VAL_IRQ_PLBU_OUT_OF_MEM     | \
+	 MALIGP2_REG_VAL_IRQ_VS_SEM_IRQ          | \
+	 MALIGP2_REG_VAL_IRQ_PLBU_SEM_IRQ        | \
+	 MALIGP2_REG_VAL_IRQ_HANG                | \
+	 MALIGP2_REG_VAL_IRQ_FORCE_HANG          | \
+	 MALIGP2_REG_VAL_IRQ_PERF_CNT_0_LIMIT    | \
+	 MALIGP2_REG_VAL_IRQ_PERF_CNT_1_LIMIT    | \
+	 MALIGP2_REG_VAL_IRQ_WRITE_BOUND_ERR     | \
+	 MALIGP2_REG_VAL_IRQ_SYNC_ERROR          | \
+	 MALIGP2_REG_VAL_IRQ_AXI_BUS_ERROR       | \
+	 MALI400GP_REG_VAL_IRQ_AXI_BUS_STOPPED     | \
+	 MALI400GP_REG_VAL_IRQ_VS_INVALID_CMD      | \
+	 MALI400GP_REG_VAL_IRQ_PLB_INVALID_CMD     | \
+	 MALI400GP_REG_VAL_IRQ_RESET_COMPLETED     | \
+	 MALI400GP_REG_VAL_IRQ_SEMAPHORE_UNDERFLOW | \
+	 MALI400GP_REG_VAL_IRQ_SEMAPHORE_OVERFLOW  | \
+	 MALI400GP_REG_VAL_IRQ_PTR_ARRAY_OUT_OF_BOUNDS)
+
+/* Mask defining the IRQs in Mali GP which we use */
+#define MALIGP2_REG_VAL_IRQ_MASK_USED \
+	(\
+	 MALIGP2_REG_VAL_IRQ_VS_END_CMD_LST      | \
+	 MALIGP2_REG_VAL_IRQ_PLBU_END_CMD_LST    | \
+	 MALIGP2_REG_VAL_IRQ_PLBU_OUT_OF_MEM     | \
+	 MALIGP2_REG_VAL_IRQ_FORCE_HANG          | \
+	 MALIGP2_REG_VAL_IRQ_WRITE_BOUND_ERR     | \
+	 MALIGP2_REG_VAL_IRQ_SYNC_ERROR          | \
+	 MALIGP2_REG_VAL_IRQ_AXI_BUS_ERROR       | \
+	 MALI400GP_REG_VAL_IRQ_VS_INVALID_CMD      | \
+	 MALI400GP_REG_VAL_IRQ_PLB_INVALID_CMD     | \
+	 MALI400GP_REG_VAL_IRQ_SEMAPHORE_UNDERFLOW | \
+	 MALI400GP_REG_VAL_IRQ_SEMAPHORE_OVERFLOW  | \
+	 MALI400GP_REG_VAL_IRQ_PTR_ARRAY_OUT_OF_BOUNDS)
+
+/* Mask defining non IRQs on MaliGP2*/
+#define MALIGP2_REG_VAL_IRQ_MASK_NONE 0
+
+/** }@ defgroup MALIGP2_IRQ*/
+
+/** @defgroup MALIGP2_STATUS
+ * The different Status values to the geometry processor.
+ *  @see MALIGP2_CTRL_REG_STATUS
+ * @{
+ */
+#define MALIGP2_REG_VAL_STATUS_VS_ACTIVE         0x0002
+#define MALIGP2_REG_VAL_STATUS_BUS_STOPPED       0x0004
+#define MALIGP2_REG_VAL_STATUS_PLBU_ACTIVE       0x0008
+#define MALIGP2_REG_VAL_STATUS_BUS_ERROR         0x0040
+#define MALIGP2_REG_VAL_STATUS_WRITE_BOUND_ERR   0x0100
+/** }@ defgroup MALIGP2_STATUS*/
+
+#define MALIGP2_REG_VAL_STATUS_MASK_ACTIVE (\
+		MALIGP2_REG_VAL_STATUS_VS_ACTIVE|\
+		MALIGP2_REG_VAL_STATUS_PLBU_ACTIVE)
+
+
+#define MALIGP2_REG_VAL_STATUS_MASK_ERROR (\
+		MALIGP2_REG_VAL_STATUS_BUS_ERROR |\
+		MALIGP2_REG_VAL_STATUS_WRITE_BOUND_ERR )
+
+/* This should be in the top 16 bit of the version register of gp.*/
+#define MALI200_GP_PRODUCT_ID 0xA07
+#define MALI300_GP_PRODUCT_ID 0xC07
+#define MALI400_GP_PRODUCT_ID 0xB07
+#define MALI450_GP_PRODUCT_ID 0xD07
+
+/**
+ * The different sources for instrumented on the geometry processor.
+ *  @see MALIGP2_REG_ADDR_MGMT_PERF_CNT_0_SRC
+ */
+
+enum MALIGP2_cont_reg_perf_cnt_src {
+	MALIGP2_REG_VAL_PERF_CNT1_SRC_NUMBER_OF_VERTICES_PROCESSED = 0x0a,
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/timestamp-arm11-cc/mali_timestamp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/timestamp-arm11-cc/mali_timestamp.c
@@ -0,0 +1,13 @@
+/*
+ * Copyright (C) 2010-2011, 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_timestamp.h"
+
+/* This file is intentionally left empty, as all functions are inlined in mali_profiling_sampler.h */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/timestamp-arm11-cc/mali_timestamp.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/timestamp-arm11-cc/mali_timestamp.h
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2010-2011, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_TIMESTAMP_H__
+#define __MALI_TIMESTAMP_H__
+
+#include "mali_osk.h"
+
+MALI_STATIC_INLINE _mali_osk_errcode_t _mali_timestamp_reset(void)
+{
+	/*
+	 * reset counters and overflow flags
+	 */
+
+	u32 mask = (1 << 0) | /* enable all three counters */
+		   (0 << 1) | /* reset both Count Registers to 0x0 */
+		   (1 << 2) | /* reset the Cycle Counter Register to 0x0 */
+		   (0 << 3) | /* 1 = Cycle Counter Register counts every 64th processor clock cycle */
+		   (0 << 4) | /* Count Register 0 interrupt enable */
+		   (0 << 5) | /* Count Register 1 interrupt enable */
+		   (0 << 6) | /* Cycle Counter interrupt enable */
+		   (0 << 8) | /* Count Register 0 overflow flag (clear or write, flag on read) */
+		   (0 << 9) | /* Count Register 1 overflow flag (clear or write, flag on read) */
+		   (1 << 10); /* Cycle Counter Register overflow flag (clear or write, flag on read) */
+
+	__asm__ __volatile__("MCR    p15, 0, %0, c15, c12, 0" : : "r"(mask));
+
+	return _MALI_OSK_ERR_OK;
+}
+
+MALI_STATIC_INLINE u64 _mali_timestamp_get(void)
+{
+	u32 result;
+
+	/* this is for the clock cycles */
+	__asm__ __volatile__("MRC    p15, 0, %0, c15, c12, 1" : "=r"(result));
+
+	return (u64)result;
+}
+
+#endif /* __MALI_TIMESTAMP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/timestamp-default/mali_timestamp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/timestamp-default/mali_timestamp.c
@@ -0,0 +1,13 @@
+/*
+ * Copyright (C) 2010-2011, 2013, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include "mali_timestamp.h"
+
+/* This file is intentionally left empty, as all functions are inlined in mali_profiling_sampler.h */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/mali/timestamp-default/mali_timestamp.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/mali/timestamp-default/mali_timestamp.h
@@ -0,0 +1,26 @@
+/*
+ * Copyright (C) 2010-2011, 2013-2014, 2018 ARM Limited. All rights reserved.
+ * 
+ * This program is free software and is provided to you under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation, and any use by you of this program is subject to the terms of such GNU licence.
+ * 
+ * A copy of the licence is included with the program, and can also be obtained from Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#ifndef __MALI_TIMESTAMP_H__
+#define __MALI_TIMESTAMP_H__
+
+#include "mali_osk.h"
+
+MALI_STATIC_INLINE _mali_osk_errcode_t _mali_timestamp_reset(void)
+{
+	return _MALI_OSK_ERR_OK;
+}
+
+MALI_STATIC_INLINE u64 _mali_timestamp_get(void)
+{
+	return _mali_osk_boot_time_get_ns();
+}
+
+#endif /* __MALI_TIMESTAMP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/silabs,si5324.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/silabs,si5324.txt
@@ -0,0 +1,61 @@
+Binding for Silicon Labs Si5324 programmable i2c clock generator.
+
+Reference
+[1] Si5324 Data Sheet
+    http://www.silabs.com/Support%20Documents/TechnicalDocs/Si5324.pdf
+
+The Si5324 is programmable i2c low-bandwidth, jitter-attenuating, precision
+clock multiplier with up to 2 output clocks. The internal structure of the 
+clock multiplier can be found in [1].
+
+==I2C device node==
+
+Required properties:
+- compatible: shall be "silabs,si5324".
+- reg: i2c device address, shall be 0x68.
+- #clock-cells: from common clock binding; shall be set to 1.
+- clocks: from common clock binding; list of parent clock
+  handles, shall be xtal reference clock or xtal. Corresponding clock
+  input names is "xtal"
+- #address-cells: shall be set to 1.
+- #size-cells: shall be set to 0.
+
+==Child nodes==
+
+Each of the clock outputs can be overwritten individually by
+using a child node to the I2C device node. If a child node for a clock
+output is not set, the eeprom configuration is not overwritten.
+
+Required child node properties:
+- reg: number of clock output.
+- clock-frequency: default output frequency at power on
+
+==Example==
+
+	/* 114.285MHz reference crystal */
+	refhdmi: refhdmi {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <114285000>;
+	};
+
+	/* Si5324 i2c clock generator */
+	si5324: clock-generator@68 {
+		status = "okay";
+		compatible = "silabs,si5324";
+		reg = <0x68>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#clock-cells = <1>;
+	
+		/* input clock(s); the XTAL is hard-wired on the ZCU102 board */
+		clocks = <&refhdmi>;
+		clock-names = "xtal";
+	
+		/* output clocks */
+		clk0 {
+			reg = <0>;
+			/* Reference clock output frequency */
+			clock-frequency = <27000000>;
+		};
+	};
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/ti,dp159.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/ti,dp159.txt
@@ -0,0 +1,31 @@
+Binding for TI DP159 programmable i2c retimer
+
+Reference
+[1] DP159 Data Sheet
+	http://www.ti.com/lit/ds/symlink/sn65dp159.pdf
+
+The SNx5DP159 device is a dual mode DisplayPort to transition-minimized
+differential signal (TMDS) retimer supporting digital video interface
+(DVI) 1.0 and high-definition multimedia interface (HDMI) 1.4b and 2.0
+output signals. The internal structure of the retimer can be found in [1].
+
+==I2C device node==
+
+Required properties:
+- compatible: shall be "ti,dp159".
+- status: shall be "okay"
+- reg: i2c device address, shall be 0x5e.
+- #clock-cells: from common clock binding; shall be set to 0.
+- #address-cells: shall be set to 1.
+- #size-cells: shall be set to 0.
+
+==Example==
+
+	dp159: hdmi-retimer@5e {
+		status = "okay";
+		compatible = "ti,dp159";
+		reg = <0x5e>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#clock-cells = <0>;
+	};			
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/xlnx,v-hdmi-rx-ss.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/xlnx,v-hdmi-rx-ss.txt
@@ -0,0 +1,116 @@
+Xilinx HDMI RX Subsystem
+
+The Xilinx HDMI RX Subsystem contains several subcores to implement
+a HDMI receiver. /hdmi/xilinx-hdmi-rx.c implements a
+V4L2 video-capture sub-device for the Xilinx Video IP Pipeline device
+(xilinx-vipp).
+
+There are 2 optional HDCP cores that can be included in the IP configuration.
+Below provided sample device tree depicts the configuration when both cores are
+included. If an optional core is included then corresponding entries for the
+core parameters (interrupts, key-management block address) must be included in
+the device tree
+
+Note: If HDCP cores are included in the design, the user must provide valid
+	  HDCP keys for the encryption to work.
+
+Refer to xlnx,vphy.txt for the phy specifics.
+
+Required Properties:
+ - compatible: Should be "xlnx,v-hdmi-rx-ss-3.1".
+ - reg: Base address and size of the IP core and hdcp1x key management block
+ - reg-names: Identification string for included register blocks
+		"hdmi-rxss": Identification string for hdmirx subsystem. Always present
+		"hdcp1x-keymngmt": Identification string for Key management block for
+			hdcp1x. [Optional]
+ - interrupts-parent: phandle for interrupt controller.
+ - interrupts: Interrupt numbers for mandatory and optional blocks
+ - interrupt-names: Identification string that binds irq number to block
+		generating the interrupt
+		"irq": interrupt for tx subcore [always present]
+		"hdcp14_irq": interrupt for hdcp1.4 core [optional - present if hdcp1x
+		is included]
+		"hdcp14_timer_irq": interrupt for hdcp1.4 timer [optional - present if
+		hdcp1x is included]
+		"hdcp22_irq": interrupt for hdcp22 core [optional - present if hdcp22
+		is included]
+		"hdcp22_timer_irq": interrupt for hdcp2.2 timer [optional - present if
+		hdcp22 is included]
+
+ - clocks: phandle of all the clocks required by IP are listed here.
+ - clock-names: names of all the clocks required by IP are listed here.
+          NOTE: Auto generated DT is providing all the clock names and handles
+          reuired by the IP.
+          NOTE: Below are the identification string that are always required.
+              "s_axi_cpu_aclk", is always required for the axi-lite clock
+              "s_axis_video_aclk" is always required for video stream clock
+
+ - phys: phandle for phy lanes registered for hdmi protocol. HDMI always
+         require 3 lanes
+ - phy-names: The identification string, "hdmi-phy0" and so on
+
+ - xlnx,input-pixels-per-clock: IP configuration for samples/clk (2, 4)
+         Note: Only 2 is supported at this time
+ - xlnx,max-bits-per-component: The data width per video component (8,10,12,16)
+         Note: Only 8 & 10 is supported at this time
+ - xlnx,edid-ram-size: Denotes amount of BRAM allocated for EDID in IP
+ - xlnx,include-hdcp-1-4: Boolean parameter that denotes if hdcp14 is included.
+		If present indicates inclusion of the optional core
+ - xlnx,include-hdcp-2-2: Boolean parameter that denotes if hdcp22 is included.
+		If present indicates inclusion of the optional core
+ - xlnx,audio-enabled: Boolean parameter to convey that design has audio
+		functionality.
+		If present, indicates optional audio core needed for audio
+		usecase is included.
+ - xlnx,snd-pcm: Reference to audio formatter block. Add this if, audio formatter
+		is going to be used for HDMI audio.
+		Needed only if "xlnx,audio-enabled" is included.
+ - ports: Video ports, using the DT bindings defined in ../video-interfaces.txt.
+          The Rx only has an output port (0).
+
+==Example==
+If hdcp1.4 is included in the design then key management block node should be
+added to the device tree
+
+	hdcp_keymngmt_blk_1: hdcp_keymngmt_blk_top@88000000 {
+		clock-names = "s_axi_aclk", "m_axis_aclk";
+		clocks = <&zynqmp_clk 71>, <&misc_clk_0>;
+		compatible = "xlnx,hdcp-keymngmt-blk-top-1.0";
+		reg = <0x0 0x88000000 0x0 0x10000>;
+	};
+
+	v_hdmi_rx_ss: v_hdmi_rx_ss@80000000 {
+		compatible = "xlnx,v-hdmi-rx-ss-3.1";
+		reg = <0x0 0xa0000000 0x0 0x100000>, <0x0 0xa0270000 0x0 0x10000>;
+		reg-names = "hdmi-rxss", "hdcp1x-keymngmt";
+		interrupt-parent = <&gic>;
+		interrupts = <0 90 4 0 104 4 0 105 4 0 108 4 0 109 4>;
+		interrupt-names = "irq", "hdcp14_irq", "hdcp14_timer_irq", "hdcp22_irq", "hdcp22_timer_irq";
+		clock-names = "s_axi_cpu_aclk", "link_clk", "s_axis_audio_aclk", "video_clk", "s_axis_video_aclk";
+		clocks = <&zynqmp_clk 71>, <&misc_clk_1>, <&zynqmp_clk 71>, <&misc_clk_2>, <&zynqmp_clk 72>;
+		phy-names = "hdmi-phy0", "hdmi-phy1", "hdmi-phy2";
+		phys = <&vphy_lane0 0 1 1 0>, <&vphy_lane1 0 1 1 0>, <&vphy_lane2 0 1 1 0>;
+
+		xlnx,input-pixels-per-clock = <0x2>;
+		xlnx,max-bits-per-component = <0xa>;
+		xlnx,edid-ram-size = <0x100>;
+		xlnx,include-hdcp-1-4;
+		xlnx,include-hdcp-2-2;
+		xlnx,audio-enabled;
+		xlnx,snd-pcm = <&audio_ss_0_audio_formatter_0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+
+				/* HDMI RX SS -> FB-WR */
+				hdmi_rxss_out: endpoint {
+					remote-endpoint = <&vcap_hdmi_in>;
+				};
+			};
+		};
+	};
+
+	Documentation of "audio_ss_0_audio_formatter_0" node is located
+	at Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/xlnx,v-hdmi-tx-ss.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/xlnx,v-hdmi-tx-ss.txt
@@ -0,0 +1,181 @@
+Xilinx HDMI TX Subsystem
+
+The Xilinx HDMI TX Subsystem contains several subcores to implement
+a HDMI Transmitter. xilinx_drm_hdmi.c implements a DRM/KMS driver
+encoder/connector interface in the output pipeline.
+
+There are 2 optional HDCP cores that can be included in the IP configuration.
+Below provided sample device tree depicts the configuration when both cores are
+included. If an optional core is included then corresponding entries for the
+core parameters (interrupts, key-management block address) must be included in
+the device tree
+
+Note: If HDCP cores are included in the design, the user must provide valid
+	  HDCP keys for the encryption to work.
+
+Note: This version of the driver interfaces with the new Xilinx DRM component
+	  framework and is not backward compatible with the earlier encoder-slave
+	  interface. As such compatibility string has been reved up to indicate the
+	  new interface.
+
+Refer to xlnx,vphy.txt for the phy specifics.
+
+Required properties:
+ - compatible: Should be "xlnx,v-hdmi-tx-ss-3.1".
+ - reg: Base address and size of the IP core and hdcp1x key management block
+ - reg-names: Identification string for included register blocks
+		"hdmi-txss": Identification string for hdmitx subsystem. Always present
+		"hdcp1x-keymngmt": Identification string for Key management block for
+			hdcp1x. [Optional]
+
+ - interrupts-parent: phandle for interrupt controller.
+ - interrupts: Interrupt numbers for mandatory and optional blocks
+ - interrupt-names: Identification string that binds irq number to block
+		generating the interrupt
+		"irq": interrupt for tx subcore [always present]
+		"hdcp14_irq": interrupt for hdcp1.4 core [optional - present if hdcp1x
+		is included]
+		"hdcp14_timer_irq": interrupt for hdcp1.4 timer [optional - present if
+		hdcp1x is included]
+		"hdcp22_irq": interrupt for hdcp22 core [optional - present if hdcp22
+		is included]
+		"hdcp22_timer_irq": interrupt for hdcp2.2 timer [optional - present if
+		hdcp22 is included]
+
+ - clocks: phandle of all the clocks required by IP are listed here.
+ - clock-names: names of all the clocks required by IP are listed here.
+          NOTE: Auto generated DT is providing all the clock names and handles
+          reuired by the IP.
+          NOTE: Below are the identification string that are always required.
+              "s_axi_cpu_aclk", is always required for the axi-lite clock
+              "s_axis_video_aclk" is always required for video stream clock
+              "txref-clk" is always required for tmds clock
+              "retimer-clk" is required only when retimer is being used
+          NOTE: "txref-clk" and "retimer-clk" needs to be explicitly added in
+          the list of clock-names and its phandle in clocks as its derived by
+          external clock.
+
+ - phys: phandle for phy lanes registered for hdmi protocol. HDMI always
+         require 3 lanes
+ - phy-names: The identification string, "hdmi-phy0" and so on
+
+ - xlnx,input-pixels-per-clock: IP configuration for samples/clk (2, 4)
+         Note: Only 2 is supported at this time
+ - xlnx,max-bits-per-component: The data width per video component (8,10,12,16)
+         Note: Only 8 & 10 is supported at this time
+ - xlnx,include-hdcp-1-4: Boolean parameter that denotes if hdcp14 is included.
+		If present indicates inclusion of the optional core
+ - xlnx,include-hdcp-2-2: Boolean parameter that denotes if hdcp22 is included.
+		If present indicates inclusion of the optional core
+ - xlnx,hdcp-authenticate: Flag to enable/disable hdcp authentication.
+		Applicable when either hdcp14 or hdcp22 is included in the design
+ - xlnx,hdcp-encrypt: Flag to enable/disable stream encryption
+ 		Applicable when either hdcp14 or hdcp22 is included in the design
+ - xlnx,audio-enabled: Boolean parameter to convey that design has audio
+                functionality.
+		If present, indicates optional audio core needed for audio
+		usecase is included.
+ - xlnx,aes_parser: Alias to audio channel status extractor block.
+		Needed only if "xlnx,audio-enabled" is included.
+ - xlnx,snd-pcm: Reference to audio formatter block. Add this if, audio formatter
+                is going to be used for HDMI audio.
+		Needed only if "xlnx,audio-enabled" is included.
+ - xlnx,xlnx-hdmi-acr-ctrl: Alias to audio clock recovery block.
+		Needed only if "xlnx,audio-enabled" is included.
+ - xlnx,vid-interface: Indicates the video interface mode (0, 1, 2)
+		0: AXI-stream
+		1: Native video
+		2: Native video (vectored DE)
+
+Optional Properties:
+ - xlnx,vpss: vpss phandle. Requied only when vpss is connected to HDMI as bridge.
+
+Sub-Node Properties:
+	The device tree will need to include a sub-node for the encoder endpoint
+	interface. This port will bind the hdmi encoder with the crtc being used
+
+	Required Properties:
+	- ports: Connects to the crtc node through the device graph binding.
+	The port should contain a 'remote-endpoint' sub-node that points to the
+	endpoint in the port of the crtc/dma-engine device node.
+
+The "retimer-clk" is optional but recommended. If specified, the corresponding
+driver should offer a CCF clock that supports .set_rate(). Through this,
+the device can retime/redrive the HDMI TX signal on the connector
+depending on the TX clock line rate. Tested with dp159.c driver.
+
+==Example==
+If hdcp1.4 is included in the design then key management block node should be
+added to the device tree
+
+	hdcp_keymngmt_blk_0: hdcp_keymngmt_blk_top@90000000 {
+		clock-names = "s_axi_aclk", "m_axis_aclk";
+		clocks = <&zynqmp_clk 71>, <&misc_clk_0>;
+		compatible = "xlnx,hdcp-keymngmt-blk-top-1.0";
+		reg = <0x0 0x90000000 0x0 0x10000>;
+	};
+
+	hdmi_acr_ctrl_0: hdmi_acr_ctrl@a0059000 {
+		/* This is a place holder node for a custom IP, user may need to update the entries */
+		compatible = "xlnx,hdmi-acr-ctrl-1.0";
+		reg = <0x0 0xa0059000 0x0 0x1000>;
+	};
+
+	v_hdmi_tx_ss: v_hdmi_tx_ss@80080000 {
+		compatible = "xlnx,v-hdmi-tx-ss-3.1";
+		reg = <0x0 0xa0080000 0x0 0x80000>, <0x0 0xa0280000 0x0 0x10000>;
+		reg-names = "hdmi-txss", "hdcp1x-keymngmt";
+		interrupt-parent = <&gic>;
+		interrupts = <0 91 4 0 106 4 0 107 4 0 110 4 0 111 4>;
+		interrupt-names = "irq", "hdcp14_irq", "hdcp14_timer_irq", "hdcp22_irq", "hdcp22_timer_irq";
+
+		clock-names = "s_axi_cpu_aclk", "link_clk", "s_axis_audio_aclk", "video_clk", "s_axis_video_aclk", "txref-clk", "retimer-clk";
+		clocks = <&zynqmp_clk 71>, <&misc_clk_1>, <&zynqmp_clk 71>, <&misc_clk_2>, <&zynqmp_clk 72>, <&si5324 0>, <&dp159>;
+		phy-names = "hdmi-phy0", "hdmi-phy1", "hdmi-phy2";
+		phys = <&vphy_lane0 0 1 1 1>, <&vphy_lane1 0 1 1 1>, <&vphy_lane2 0 1 1 1>;
+
+		xlnx,input-pixels-per-clock = <0x2>;
+		xlnx,max-bits-per-component = <0xa>;
+		xlnx,include-hdcp-1-4;
+		xlnx,include-hdcp-2-2;
+		/* settings for HDCP */
+		xlnx,hdcp-authenticate = <0x1>;
+		xlnx,hdcp-encrypt = <0x1>;
+		xlnx,audio-enabled;
+		xlnx,xlnx-hdmi-acr-ctrl = <&hdmi_acr_ctrl_0>;
+		xlnx,snd-pcm = <&audio_ss_0_audio_formatter_0>;
+		xlnx,vid-interface = <0x1>;
+		xlnx,vpss = <&v_proc_ss_0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			encoder_hdmi_port: port@0 {
+				reg = <0>;
+				hdmi_encoder: endpoint {
+					remote-endpoint = <&dmaengine_crtc>;
+				};
+			};
+		};
+	};
+
+	v_drm_dmaengine_drv: drm-dmaengine-drv {
+		compatible = "xlnx,pl-disp";
+		dmas = <&hdmi_output_v_frmbuf_rd_0 0>;
+		dma-names = "dma0";
+		xlnx,vformat = "BG24";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dmaengine_port: port@0 {
+			reg = <0>;
+			dmaengine_crtc: endpoint {
+				remote-endpoint = <&hdmi_encoder>;
+			};
+		};
+	};
+
+	Documentation of "audio_ss_0_audio_formatter_0" node is located
+	at Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt
+
+	Documentation of "v_proc_ss_0" node is located at
+	Documentation/devicetree/bindings/display/xlnx/xlnx,vpss-scaler.txt
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/xlnx,vphy.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Documentation/devicetree/bindings/xlnx,vphy.txt
@@ -0,0 +1,154 @@
+Xilinx VPHY (Staging)
+
+The Xilinx Video PHY is a high-level video-specific wrapper around
+different versions of the GT PHY. Its driver is phy/phy-xilinx-vphy.c
+This now supports HDMI on Versal too.
+
+It offers the PHY driver interface as well as higher-level video
+specific support functions.
+
+Its current users are Xilinx HDMI RX/TX SS.
+(See xlnx,v-hdmi-rx-ss.txt and xlnx,v-hdmi-tx-ss.txt)
+
+
+Required Properties:
+ - compatible: Should be "xlnx,vid-phy-controller-2.2".
+   For Versal it should be "xlnx,hdmi-gt-controller-1.0".
+ - reg: Base address and size of the IP core.
+ - interrupts: Interrupt number.
+ - interrupts-parent: phandle for interrupt controller.
+
+ - clocks: phandle of all the clocks required by IP are listed here.
+ - clock-names: names of all the clocks required by IP are listed here.
+          NOTE: Auto generated DT is providing all the clock names and handles
+          reuired by the IP.
+          NOTE: The identification string, "vid_phy_axi4lite_aclk", is always
+          required in non Versal mode. In Versal, the string is "axi4lite_aclk".
+          NOTE: The identification string "dru-clk" is always required if
+          NI DRU (nidru parameter) is selected for phy. This needs to be
+          explicitly added in the list of clock-names and its phandle in clocks
+          as its derived by external clock.
+
+ - xlnx,input-pixels-per-clock: IP configuration for samples/clk (1, 2, 4)
+         Note: Only 2 is supported at this time
+ - xlnx,nidru: flag to indicate if DRU is present.
+ - xlnx,nidru-refclk-sel: DRU clock selector
+ - xlnx,rx-no-of-channels: Required Rx channels for registered protocol
+ - xlnx,rx-pll-selection: Rx pll selector
+ - xlnx,rx-protocol: 1=HDMI, 0=DP (Note: Only HDMI is supported at this time)
+ - xlnx,rx-refclk-sel: Reference Rx clock selector
+ - xlnx,tx-no-of-channels: Required Rx channels for registered protocol
+ - xlnx,tx-pll-selection = Tx pll selector
+ - xlnx,tx-protocol: 1=HDMI, 0=DP (Note: Only HDMI is supported at this time)
+ - xlnx,tx-refclk-sel: Reference Rx clock selector
+ - xlnx,hdmi-fast-switch: Flag to indicate fast switching logic availability
+ - xlnx,transceiver-type: GT type. Must be set per GT device used
+ - xlnx,tx-buffer-bypass: Flag to indicate buffer bypass logic availability
+ - xlnx,transceiver-width: Defines 4 Byte or 2 Byte mode
+                      (Note: Only 2 byte is supported at this time)
+ - xlnx,use-gt-ch4-hdmi: Enables the usage of 4th TX GT channel.
+                      (Default value is 0.
+                      If selected in GUI, then value will be 1)
+ - xlnx,rx-frl-refclk-sel: Reference clock for Rx in FRL mode in Versal only
+ - xlnx,tx-frl-refclk-sel: Reference clock for Tx in FRL mode in Versal only
+
+ - lane<n>: (port (child) nodes)
+	lane0:
+		- #phy-cells	: Should be 4
+			Cell after port phandle is device type from:
+			- <controller_type controller_instance is_shared direction_tx>
+
+			controller_type = 0 for HDMI
+            controller_instance = [0, ...] indexes the instance of the protocol
+                                  controller
+            is_shared = 1 if the RX and TX can be shared across the same
+			            protocol/controller
+            direction_tx = 0 for RX and 1 for TX
+
+(These properties are intended for future steering of multiple protocols
+sharing VPHYs, and are therefore subject to change.)
+
+==Example==
+
+	vid_phy_controller: vid_phy_controller@80120000 {
+		compatible = "xlnx,vid-phy-controller-2.2";
+		reg = <0x0 0xa0090000 0x0 0x10000>;
+		interrupts = <0 92 4>;
+		interrupt-parent = <&gic>;
+		clock-names = "mgtrefclk0_pad_p_in", "mgtrefclk0_pad_n_in", "mgtrefclk1_pad_p_in", "mgtrefclk1_pad_n_in", "gtsouthrefclk0_in", "gtsouthrefclk0_odiv2_in", "vid_phy_tx_axi4s_aclk", "vid_phy_rx_axi4s_aclk", "vid_phy_sb_aclk", "vid_phy_axi4lite_aclk", "drpclk", "dru-clk";
+		clocks = <&misc_clk_0>, <&misc_clk_0>, <&misc_clk_0>, <&misc_clk_0>, <&misc_clk_3>, <&misc_clk_3>, <&misc_clk_1>, <&misc_clk_1>, <&zynqmp_clk 71>, <&zynqmp_clk 71>, <&zynqmp_clk 71>, <&si570_2>;
+
+		xlnx,input-pixels-per-clock = <0x2>;
+		xlnx,nidru = <0x1>;
+		xlnx,nidru-refclk-sel = <0x4>;
+		xlnx,rx-no-of-channels = <0x3>;
+		xlnx,rx-pll-selection = <0x0>;
+		xlnx,rx-protocol = <0x1>;
+		xlnx,rx-refclk-sel = <0x1>;
+		xlnx,tx-no-of-channels = <0x3>;
+		xlnx,tx-pll-selection = <0x6>;
+		xlnx,tx-protocol = <0x1>;
+		xlnx,tx-refclk-sel = <0x0>;
+		xlnx,hdmi-fast-switch = <0x1>;
+		xlnx,transceiver-type = <0x5>;
+		xlnx,tx-buffer-bypass = <0x1>;
+		xlnx,transceiver-width = <0x2>;
+		xlnx,use-gt-ch4-hdmi = <0>;
+
+		vphy_lane0: vphy_lane@0 {
+			#phy-cells = <4>;
+		};
+		vphy_lane1: vphy_lane@1 {
+			#phy-cells = <4>;
+		};
+		vphy_lane2: vphy_lane@2 {
+			#phy-cells = <4>;
+		};
+		vphy_lane3: vphy_lane@3 {
+			#phy-cells = <4>;
+		};
+	};
+
+==Example for Versal==
+
+	hdmi_gt_controller_1: hdmi_gt_controller@a4080000 {
+			clock-names = "gt_refclk1_odiv2", "sb_aclk", "axi4lite_aclk", "apb_clk", "dru-clk";
+			clocks = <&misc_clk_0>, <&versal_clk 65>, <&versal_clk 65>, <&versal_clk 65>, <&si570_2>;
+			compatible = "xlnx,hdmi-gt-controller-1.0";
+			interrupt-names = "irq";
+			interrupt-parent = <&gic>;
+			interrupts = <0 84 4>;
+			reg = <0x0 0xa4080000 0x0 0x10000>;
+			xlnx,err-irq-en = <0>;
+			xlnx,hdmi-fast-switch = <0>;
+			xlnx,input-pixels-per-clock = <2>;
+			xlnx,nidru = <1>;
+			xlnx,nidru-refclk-sel = <2>;
+			xlnx,rx-frl-refclk-sel = <2>;
+			xlnx,rx-no-of-channels = <4>;
+			xlnx,rx-pll-selection = <8>;
+			xlnx,rx-protocol = <3>;
+			xlnx,rx-refclk-sel = <0>;
+			xlnx,transceiver-type = <7>;
+			xlnx,transceiver-width = <2>;
+			xlnx,tx-buffer-bypass = <1>;
+			xlnx,tx-frl-refclk-sel = <2>;
+			xlnx,tx-no-of-channels = <4>;
+			xlnx,tx-pll-selection = <7>;
+			xlnx,tx-protocol = <1>;
+			xlnx,tx-refclk-sel = <1>;
+			xlnx,use-gt-ch4-hdmi = <1>;
+			vphy_lane0: vphy_lane@0 {
+				#phy-cells = <4>;
+			};
+			vphy_lane1: vphy_lane@1 {
+				#phy-cells = <4>;
+			};
+			vphy_lane2: vphy_lane@2 {
+				#phy-cells = <4>;
+			};
+			vphy_lane3: vphy_lane@3 {
+				#phy-cells = <4>;
+			};
+		};
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Kbuild
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Kbuild
@@ -0,0 +1,2 @@
+obj-m	+= hdmi/
+obj-m	+= misc/
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/LICENSE.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/LICENSE.md
@@ -0,0 +1 @@
+see source code files for copyright notices and license text
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/Makefile
@@ -0,0 +1,18 @@
+SRC := $(shell pwd)
+
+obj-m	+= hdmi/
+obj-m	+= misc/
+
+all:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) O=$(O) modules
+
+modules_install:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules_install
+
+clean:
+	find . -name "*.ko" -type f -delete
+	find . -name "*.o" -type f -delete
+	find . -name "*.order" -type f -delete
+	find . -name "*.cmd" -type f -delete
+	find . -name "*.mod*" -type f -delete
+	rm -f Module.symvers
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/README.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/README.md
@@ -0,0 +1 @@
+Xilinx HDMI Linux out-of-tree modules for Yocto.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/Makefile
@@ -0,0 +1,154 @@
+# build 3 modules: vphy hdmi-rx and hdmi-tx
+obj-m += xilinx-vphy.o xilinx-hdmi-rx.o xilinx-hdmi-tx.o
+
+# in same cases only used to check against presence, i.e. >0, actual number is not used
+ccflags-y := -DXPAR_XVPHY_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XHDMIPHY1_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XV_HDMIRXSS_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XV_HDMITXSS_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XV_HDMIRX_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XV_HDMITX_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XVTC_NUM_INSTANCES=4
+
+ccflags-y += -DXPAR_VPHY_0_TRANSCEIVER=5
+ccflags-y += -DXPAR_VPHY_0_RX_PROTOCOL=1
+ccflags-y += -DXPAR_VPHY_0_TX_PROTOCOL=1
+ccflags-y += -DXPAR_HDMIPHY1_0_TRANSCEIVER=7
+# Below two parameters are notused anywhere in the code
+ccflags-y += -DXPAR_HDMIPHY1_0_RX_PROTOCOL=1
+ccflags-y += -DXPAR_HDMIPHY1_0_TX_PROTOCOL=1
+ccflags-y += -DXPAR_XV_HDMIRX_0_DEVICE_ID=0
+ccflags-y += -DXPAR_XV_HDMITX_0_DEVICE_ID=0
+
+ccflags-y += -DXPAR_XHDCP_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XHDCP22_RX_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XHDCP22_TX_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XHDCP22_MMULT_NUM_INSTANCES=4
+ccflags-y += -DXPAR_XHDCP22_CIPHER_NUM_INSTANCES=8
+ccflags-y += -DXPAR_XHDCP22_RNG_NUM_INSTANCES=8
+ccflags-y += -DXPAR_XTMRCTR_NUM_INSTANCES=16
+
+ccflags-y += -I${srctree}/${src}/include -I${srctree}/${src}/phy-xilinx-vphy
+
+# the BSP code uses C99 style declarations. The kernel is on C89, but steps to C11 are underway.
+ccflags-y += -Wno-declaration-after-statement
+ccflags-y += -Wno-unused-function
+ccflags-y += -Wno-unused-label
+ccflags-y += -Wno-unused-value
+ccflags-y += -Wno-unused-variable
+
+# V4L2 (HDMI RX)
+xilinx-hdmi-rx-objs := xilinx-hdmirx.o
+
+# the C API around the IP registers
+CFLAGS_xilinx-hdmirx.o += -I$(src)/xilinx-hdmi-rx/
+CFLAGS_xilinx-hdmirx.o += -I$(src)/include/
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirx.o
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirx_sinit.o
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirx_intr.o
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirxss.o
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirxss_log.o
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirxss_coreinit.o
+xilinx-hdmi-rx-objs += xilinx-hdmi-rx/xv_hdmirxss_hdcp.o
+xilinx-hdmi-rx-objs += xlnx_hdmirx_audio.o
+
+# DRM (HDMI TX)
+xilinx-hdmi-tx-objs := xilinx_drm_hdmi.o
+
+# the C API around the IP registers
+CFLAGS_xilinx_drm_hdmi.o += -I$(src)/xilinx-hdmi-tx/
+CFLAGS_xilinx_drm_hdmi.o += -I$(src)/include/ -Idrivers/gpu/drm/xilinx/
+
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitx.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitx_sinit.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitx_intr.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitxss.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitxss_log.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitxss_coreinit.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xv_hdmitxss_hdcp.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xvtc.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xvtc_intr.o
+xilinx-hdmi-tx-objs += xilinx-hdmi-tx/xvtc_sinit.o
+xilinx-hdmi-tx-objs += xlnx_hdmitx_audio.o
+
+# PHY (HDMI RX/TX)
+xilinx-vphy-objs := phy-vphy.o
+
+# the C API around the IP registers
+CFLAGS_phy-vphy.o += -I$(src)/phy-xilinx-vphy/
+CFLAGS_phy-vphy.o += -I$(src)/include/
+xilinx-vphy-objs += phy-xilinx-vphy/xdebug.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_i.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_gthe4.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_mmcme4.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_hdmi.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_hdmi_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_log.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvphy_sinit.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_i.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_gtye5.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_mmcme5.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_hdmi.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_hdmi_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_log.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdmiphy1_sinit.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvidc.o
+xilinx-vphy-objs += phy-xilinx-vphy/xvidc_timings_table.o
+
+#hdmi common
+xilinx-vphy-objs += phy-xilinx-vphy/xv_hdmic.o
+xilinx-vphy-objs += phy-xilinx-vphy/xv_hdmic_vsif.o
+
+#hdcp1x sources
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_platform.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_port.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_port_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_port_hdmi_rx.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_port_hdmi_tx.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_cipher.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_cipher_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_rx.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_tx.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_intr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_sinit.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp1x_selftest.o
+
+#hdcp22 common
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_cipher.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_cipher_sinit.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_mmult.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_mmult_sinit.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_rng.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_rng_sinit.o
+
+#hdcp library
+xilinx-vphy-objs += phy-xilinx-vphy/bigdigits.o
+xilinx-vphy-objs += phy-xilinx-vphy/aes.o
+xilinx-vphy-objs += phy-xilinx-vphy/hmac.o
+xilinx-vphy-objs += phy-xilinx-vphy/sha1.o
+xilinx-vphy-objs += phy-xilinx-vphy/sha2.o
+
+#hdcp key/password decryption
+xilinx-vphy-objs += phy-xilinx-vphy/aes256.o
+
+#timer
+xilinx-vphy-objs += phy-xilinx-vphy/xtmrctr.o
+xilinx-vphy-objs += phy-xilinx-vphy/xtmrctr_l.o
+xilinx-vphy-objs += phy-xilinx-vphy/xtmrctr_sinit.o
+xilinx-vphy-objs += phy-xilinx-vphy/xtmrctr_options.o
+xilinx-vphy-objs += phy-xilinx-vphy/xtmrctr_intr.o
+
+#hdcp22-tx
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_tx.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_tx_crypt.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_tx_sinit.o
+
+#hdcp22-rx
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_rx.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_rx_crypt.o
+xilinx-vphy-objs += phy-xilinx-vphy/xhdcp22_rx_sinit.o
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/include/linux/phy/phy-vphy.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/include/linux/phy/phy-vphy.h
@@ -0,0 +1,33 @@
+/*
+ * Xilinx VPHY header
+ *
+ * Copyright (C) 2016-2017 Xilinx, Inc.
+ *
+ * Author: Leon Woestenberg <leon@sidebranch.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _PHY_VPHY_H_
+#define _PHY_VPHY_H_
+
+/* @TODO change directory name on production release */
+#include "xvphy.h"
+#include "xhdmiphy1.h"
+
+struct phy;
+
+/* VPHY is built (either as module or built-in) */
+extern void *xvphy_get_xvphy(struct phy *phy);
+extern void xvphy_mutex_lock(struct phy *phy);
+extern void xvphy_mutex_unlock(struct phy *phy);
+extern int xvphy_do_something(struct phy *phy);
+
+#endif /* _PHY_VPHY_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-vphy.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-vphy.c
@@ -0,0 +1,1008 @@
+/*
+ * Xilinx VPHY driver
+ *
+ * The Video Phy is a high-level wrapper around the GT to configure it
+ * for video applications. The driver also provides common functionality
+ * for its tightly-bound video protocol drivers such as HDMI RX/TX.
+ *
+ * Copyright (C) 2016, 2017 Leon Woestenberg <leon@sidebranch.com>
+ * Copyright (C) 2014, 2015, 2017 Xilinx, Inc.
+ *
+ * Authors: Leon Woestenberg <leon@sidebranch.com>
+ *          Rohit Consul <rohitco@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <dt-bindings/phy/phy.h>
+#include <linux/list.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+
+#include "linux/phy/phy-vphy.h"
+
+/* baseline driver includes */
+#include "phy-xilinx-vphy/xvphy.h"
+#include "phy-xilinx-vphy/xvphy_i.h"
+#include "phy-xilinx-vphy/xhdmiphy1.h"
+#include "phy-xilinx-vphy/xhdmiphy1_i.h"
+
+/* common RX/TX */
+#include "phy-xilinx-vphy/xdebug.h"
+#include "phy-xilinx-vphy/xvidc.h"
+#include "phy-xilinx-vphy/xtmrctr.h"
+#include "phy-xilinx-vphy/xhdcp1x.h"
+#include "phy-xilinx-vphy/xhdcp22_rx.h"
+#include "phy-xilinx-vphy/xhdcp22_tx.h"
+#include "phy-xilinx-vphy/bigdigits.h"
+#include "phy-xilinx-vphy/xhdcp22_cipher.h"
+#include "phy-xilinx-vphy/xhdcp22_mmult.h"
+#include "phy-xilinx-vphy/xhdcp22_rng.h"
+#include "phy-xilinx-vphy/xhdcp22_common.h"
+#include "phy-xilinx-vphy/aes256.h"
+#include "phy-xilinx-vphy/xv_hdmic.h"
+#include "phy-xilinx-vphy/xv_hdmic_vsif.h"
+
+#define XVPHY_DRU_REF_CLK_HZ	156250000
+/* TODO - [Versal] - This needs to be changed for versal */
+#define XHDMIPHY1_DRU_REF_CLK_HZ	200000000
+
+#define hdmi_mutex_lock(x) mutex_lock(x)
+#define hdmi_mutex_unlock(x) mutex_unlock(x)
+
+/**
+ * struct xvphy_lane - representation of a lane
+ * @phy: pointer to the kernel PHY device
+ *
+ * @type: controller which uses this lane
+ * @lane: lane number
+ * @protocol: protocol in which the lane operates
+ * @ref_clk: enum of allowed ref clock rates for this lane PLL
+ * @pll_lock: PLL status
+ * @data: pointer to hold private data
+ * @direction: 0=rx, 1=tx
+ * @share_laneclk: lane number of the clock to be shared
+ */
+struct xvphy_lane {
+	struct phy *phy;
+	u8 type;
+	u8 lane;
+	u8 protocol;
+	bool pll_lock;
+	/* data is pointer to parent xvphy_dev */
+	void *data;
+	bool direction_tx;
+	u32 share_laneclk;
+};
+
+/**
+ * struct xvphy_dev - representation of a Xilinx Video PHY
+ * @dev: pointer to device
+ * @iomem: serdes base address
+ */
+struct xvphy_dev {
+	struct device *dev;
+	/* virtual remapped I/O memory */
+	void __iomem *iomem;
+	int irq;
+	/* protects the XVphy/XHdmiphy1 baseline against concurrent access */
+	struct mutex xvphy_mutex;
+	struct xvphy_lane *lanes[4];
+	/* bookkeeping for the baseline subsystem driver instance */
+	XVphy xvphy;
+	XHdmiphy1 xgtphy;
+	/* AXI Lite clock drives the clock detector */
+	struct clk *axi_lite_clk;
+	/* NI-DRU clock input */
+	struct clk *dru_clk;
+	/* If Video Phy flag */
+	u32 isvphy;
+};
+
+/* given the (Linux) phy handle, return the xvphy */
+void *xvphy_get_xvphy(struct phy *phy)
+{
+	struct xvphy_lane *vphy_lane = phy_get_drvdata(phy);
+	struct xvphy_dev *vphy_dev = vphy_lane->data;
+
+	if (vphy_dev->isvphy)
+		return (void *)&vphy_dev->xvphy;
+
+	return (void *)&vphy_dev->xgtphy;
+}
+EXPORT_SYMBOL_GPL(xvphy_get_xvphy);
+
+/* given the (Linux) phy handle, enter critical section of xvphy baseline code
+ * XVphy/XHdmiphy1 functions must be called with mutex acquired to prevent concurrent access
+ * by XVphy/XHdmiphy1 and upper-layer video protocol drivers */
+void xvphy_mutex_lock(struct phy *phy)
+{
+	struct xvphy_lane *vphy_lane = phy_get_drvdata(phy);
+	struct xvphy_dev *vphy_dev = vphy_lane->data;
+	hdmi_mutex_lock(&vphy_dev->xvphy_mutex);
+}
+EXPORT_SYMBOL_GPL(xvphy_mutex_lock);
+
+void xvphy_mutex_unlock(struct phy *phy)
+{
+	struct xvphy_lane *vphy_lane = phy_get_drvdata(phy);
+	struct xvphy_dev *vphy_dev = vphy_lane->data;
+	hdmi_mutex_unlock(&vphy_dev->xvphy_mutex);
+}
+EXPORT_SYMBOL_GPL(xvphy_mutex_unlock);
+
+/* XVphy functions must be called with mutex acquired to prevent concurrent access
+ * by XVphy and upper-layer video protocol drivers */
+EXPORT_SYMBOL_GPL(XVphy_GetPllType);
+EXPORT_SYMBOL_GPL(XVphy_IBufDsEnable);
+EXPORT_SYMBOL_GPL(XVphy_SetHdmiCallback);
+EXPORT_SYMBOL_GPL(XVphy_HdmiCfgCalcMmcmParam);
+EXPORT_SYMBOL_GPL(XVphy_MmcmStart);
+EXPORT_SYMBOL_GPL(XVphy_HdmiDebugInfo);
+EXPORT_SYMBOL_GPL(XVphy_RegisterDebug);
+EXPORT_SYMBOL_GPL(XVphy_LogShow);
+EXPORT_SYMBOL_GPL(XVphy_DruGetRefClkFreqHz);
+EXPORT_SYMBOL_GPL(XVphy_GetLineRateHz);
+
+/* exclusively required by TX */
+EXPORT_SYMBOL_GPL(XVphy_Clkout1OBufTdsEnable);
+EXPORT_SYMBOL_GPL(XVphy_SetHdmiTxParam);
+EXPORT_SYMBOL_GPL(XVphy_IsBonded);
+EXPORT_SYMBOL_GPL(XVphy_ClkDetFreqReset);
+EXPORT_SYMBOL_GPL(XVphy_ClkDetGetRefClkFreqHz);
+
+/* XHdmiphy1 functions must be called with mutex acquired to prevent concurrent access
+ * by XHdmiphy1 and upper-layer video protocol drivers */
+EXPORT_SYMBOL_GPL(XHdmiphy1_GetPllType);
+EXPORT_SYMBOL_GPL(XHdmiphy1_IBufDsEnable);
+EXPORT_SYMBOL_GPL(XHdmiphy1_SetHdmiCallback);
+EXPORT_SYMBOL_GPL(XHdmiphy1_HdmiCfgCalcMmcmParam);
+EXPORT_SYMBOL_GPL(XHdmiphy1_MmcmStart);
+EXPORT_SYMBOL_GPL(XHdmiphy1_HdmiDebugInfo);
+EXPORT_SYMBOL_GPL(XHdmiphy1_RegisterDebug);
+EXPORT_SYMBOL_GPL(XHdmiphy1_LogShow);
+EXPORT_SYMBOL_GPL(XHdmiphy1_DruGetRefClkFreqHz);
+EXPORT_SYMBOL_GPL(XHdmiphy1_GetLineRateHz);
+
+/* exclusively required by TX */
+EXPORT_SYMBOL_GPL(XHdmiphy1_Clkout1OBufTdsEnable);
+EXPORT_SYMBOL_GPL(XHdmiphy1_SetHdmiTxParam);
+//EXPORT_SYMBOL_GPL(XHdmiphy1_IsBonded);
+EXPORT_SYMBOL_GPL(XHdmiphy1_ClkDetFreqReset);
+EXPORT_SYMBOL_GPL(XHdmiphy1_ClkDetGetRefClkFreqHz);
+EXPORT_SYMBOL_GPL(XHdmiphy1_TxPllreset);
+
+static void xvphy_intr_disable(struct xvphy_dev *vphydev)
+{
+	if (vphydev->isvphy)
+		XVphy_IntrDisable(&vphydev->xvphy, XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE |
+			XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE |
+			XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK |
+			XVPHY_INTR_HANDLER_TYPE_QPLL0_LOCK |
+			XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE |
+			XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK |
+			XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT |
+			XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+	else
+		XHdmiphy1_IntrDisable(&vphydev->xgtphy, XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+}
+
+static void xvphy_intr_enable(struct xvphy_dev *vphydev)
+{
+	if (vphydev->isvphy)
+		XVphy_IntrEnable(&vphydev->xvphy, XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE |
+			XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE |
+			XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK |
+			XVPHY_INTR_HANDLER_TYPE_QPLL0_LOCK |
+			XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE |
+			XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK |
+			XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE |
+			XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT |
+			XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+	else
+		XHdmiphy1_IntrEnable(&vphydev->xgtphy, XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE |
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT |
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+}
+
+static irqreturn_t xvphy_irq_handler(int irq, void *dev_id)
+{
+	struct xvphy_dev *vphydev;
+
+	vphydev = (struct xvphy_dev *)dev_id;
+	if (!vphydev)
+		return IRQ_NONE;
+
+	/* Disable interrupts in the VPHY, they are re-enabled once serviced */
+	xvphy_intr_disable(vphydev);
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t xvphy_irq_thread(int irq, void *dev_id)
+{
+	struct xvphy_dev *vphydev;
+	u32 IntrStatus;
+
+	vphydev = (struct xvphy_dev *)dev_id;
+	if (!vphydev)
+		return IRQ_NONE;
+
+	/* call baremetal interrupt handler with mutex locked */
+	hdmi_mutex_lock(&vphydev->xvphy_mutex);
+
+	if (vphydev->isvphy) {
+		IntrStatus = XVphy_ReadReg(vphydev->xvphy.Config.BaseAddr, XVPHY_INTR_STS_REG);
+		dev_dbg(vphydev->dev,"XVphy IntrStatus = 0x%08x\n", IntrStatus);
+	} else {
+		IntrStatus = XHdmiphy1_ReadReg(vphydev->xgtphy.Config.BaseAddr, XHDMIPHY1_INTR_STS_REG);
+		dev_dbg(vphydev->dev,"XHdmiphy1 IntrStatus = 0x%08x\n", IntrStatus);
+	}
+
+	/* handle pending interrupts */
+	if (vphydev->isvphy)
+		XVphy_InterruptHandler(&vphydev->xvphy);
+	else
+		XHdmiphy1_InterruptHandler(&vphydev->xgtphy);
+	hdmi_mutex_unlock(&vphydev->xvphy_mutex);
+
+	/* Enable interrupt requesting in the VPHY */
+	xvphy_intr_enable(vphydev);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xvphy_phy_init - initializes a lane
+ * @phy: pointer to kernel PHY device
+ *
+ * Return: 0 on success or error on failure
+ */
+static int xvphy_phy_init(struct phy *phy)
+{
+	struct xvphy_lane *vphy_lane = phy_get_drvdata(phy);
+	struct xvphy_dev *vphy_dev = vphy_lane->data;
+
+	dev_dbg(vphy_dev->dev, "xvphy_phy_init(%p).\n", phy);
+	return 0;
+}
+
+/**
+ * xvphy_xlate - provides a PHY specific to a controller
+ * @dev: pointer to device
+ * @args: arguments from dts
+ *
+ * Return: pointer to kernel PHY device or error on failure
+ *
+ */
+static struct phy *xvphy_xlate(struct device *dev,
+				   struct of_phandle_args *args)
+{
+	struct xvphy_dev *vphydev = dev_get_drvdata(dev);
+	struct xvphy_lane *vphy_lane = NULL;
+	struct device_node *phynode = args->np;
+	int index;
+	u8 controller;
+	u8 instance_num;
+
+	if (args->args_count != 4) {
+		dev_err(dev, "Invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+	if (!of_device_is_available(phynode)) {
+		dev_warn(dev, "requested PHY is disabled\n");
+		return ERR_PTR(-ENODEV);
+	}
+	for (index = 0; index < of_get_child_count(dev->of_node); index++) {
+		if (phynode == vphydev->lanes[index]->phy->dev.of_node) {
+			vphy_lane = vphydev->lanes[index];
+			break;
+		}
+	}
+	if (!vphy_lane) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* get type of controller from lanes */
+	controller = args->args[0];
+
+	/* get controller instance number */
+	instance_num = args->args[1];
+
+	/* Check if lane sharing is required */
+	vphy_lane->share_laneclk = args->args[2];
+
+	/* get the direction for controller from lanes */
+	vphy_lane->direction_tx = args->args[3];
+
+	return vphy_lane->phy;
+}
+
+/* Local Global table for phy instance(s) configuration settings */
+XVphy_Config XVphy_ConfigTable[XPAR_XVPHY_NUM_INSTANCES];
+XHdmiphy1_Config XHdmiphy1_ConfigTable[XPAR_XHDMIPHY1_NUM_INSTANCES];
+
+static struct phy_ops xvphy_phyops = {
+	.init		= xvphy_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int instance = 0;
+/* TX uses [1, 127], RX uses [128, 254] and VPHY uses [256, ...]. Note that 255 is used for not-present. */
+#define VPHY_DEVICE_ID_BASE 256
+
+static int vphy_parse_of(struct xvphy_dev *vphydev, void *c)
+{
+	struct device *dev = vphydev->dev;
+	struct device_node *node = dev->of_node;
+	int rc;
+	u32 val;
+	bool has_err_irq;
+	XVphy_Config *vphycfg = (XVphy_Config *)c;
+	XHdmiphy1_Config *xgtphycfg = (XHdmiphy1_Config *)c;
+
+	rc = of_property_read_u32(node, "xlnx,transceiver-type", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->XcvrType = val;
+	else
+		xgtphycfg->XcvrType = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-buffer-bypass", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->TxBufferBypass = val;
+	else
+		xgtphycfg->TxBufferBypass = val;
+
+	rc = of_property_read_u32(node, "xlnx,input-pixels-per-clock", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->Ppc = val;
+	else
+		xgtphycfg->Ppc = val;
+
+	rc = of_property_read_u32(node, "xlnx,nidru", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->DruIsPresent = val;
+	else
+		xgtphycfg->DruIsPresent = val;
+
+	rc = of_property_read_u32(node, "xlnx,nidru-refclk-sel", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->DruRefClkSel = val;
+	else
+		xgtphycfg->DruRefClkSel = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-no-of-channels", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->RxChannels = val;
+	else
+		xgtphycfg->RxChannels = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-no-of-channels", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->TxChannels = val;
+	else
+		xgtphycfg->TxChannels = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-protocol", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->RxProtocol = val;
+	else
+		xgtphycfg->RxProtocol = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-protocol", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->TxProtocol = val;
+	else
+		xgtphycfg->TxProtocol = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-refclk-sel", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->RxRefClkSel = val;
+	else
+		xgtphycfg->RxRefClkSel = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-refclk-sel", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->TxRefClkSel = val;
+	else
+		xgtphycfg->TxRefClkSel = val;
+
+	rc = of_property_read_u32(node, "xlnx,rx-pll-selection", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->RxSysPllClkSel = val;
+	else
+		xgtphycfg->RxSysPllClkSel = val;
+
+	rc = of_property_read_u32(node, "xlnx,tx-pll-selection", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->TxSysPllClkSel = val;
+	else
+		xgtphycfg->TxSysPllClkSel = val;
+
+	rc = of_property_read_u32(node, "xlnx,hdmi-fast-switch", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->HdmiFastSwitch = val;
+	else
+		xgtphycfg->HdmiFastSwitch = val;
+
+	rc = of_property_read_u32(node, "xlnx,transceiver-width", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->TransceiverWidth = val;
+	else
+		xgtphycfg->TransceiverWidth = val;
+
+	has_err_irq = false;
+	has_err_irq = of_property_read_bool(node, "xlnx,err-irq-en");
+	if (vphydev->isvphy)
+		vphycfg->ErrIrq = has_err_irq;
+	else
+		xgtphycfg->ErrIrq = has_err_irq;
+
+	rc = of_property_read_u32(node, "xlnx,use-gt-ch4-hdmi", &val);
+	if (rc < 0)
+		goto error_dt;
+	if (vphydev->isvphy)
+		vphycfg->UseGtAsTxTmdsClk = val;
+	else
+		xgtphycfg->UseGtAsTxTmdsClk = val;
+
+	if (!vphydev->isvphy) {
+		rc = of_property_read_u32(node, "xlnx,rx-frl-refclk-sel", &val);
+		if (rc < 0)
+			goto error_dt;
+		xgtphycfg->RxFrlRefClkSel = val;
+
+		rc = of_property_read_u32(node, "xlnx,tx-frl-refclk-sel", &val);
+		if (rc < 0)
+			goto error_dt;
+		xgtphycfg->TxFrlRefClkSel = val;
+	}
+
+	return 0;
+
+error_dt:
+	dev_err(vphydev->dev, "Error parsing device tree");
+	return -EINVAL;
+}
+
+/* Match table for of_platform binding */
+static const struct of_device_id xvphy_of_match[] = {
+	{ .compatible = "xlnx,hdmi-gt-controller-1.0" },
+	{ .compatible = "xlnx,vid-phy-controller-2.2" },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xvphy_of_match);
+
+/**
+ * xvphy_probe - The device probe function for driver initialization.
+ * @pdev: pointer to the platform device structure.
+ *
+ * Return: 0 for success and error value on failure
+ */
+static int xvphy_probe(struct platform_device *pdev)
+{
+	struct device_node *child, *np = pdev->dev.of_node;
+	struct xvphy_dev *vphydev;
+	struct phy_provider *provider;
+	struct phy *phy;
+	unsigned long axi_lite_rate;
+	unsigned long dru_clk_rate;
+
+	struct resource *res;
+	int port = 0, index = 0;
+	int ret;
+	u32 Status;
+	u32 Data;
+	u16 DrpVal;
+
+	void __iomem *iomem1;
+	const struct of_device_id *match;
+
+	dev_info(&pdev->dev, "probe started\n");
+	vphydev = devm_kzalloc(&pdev->dev, sizeof(*vphydev), GFP_KERNEL);
+	if (!vphydev)
+		return -ENOMEM;
+
+	/* mutex that protects against concurrent access */
+	mutex_init(&vphydev->xvphy_mutex);
+
+	vphydev->dev = &pdev->dev;
+	/* set a pointer to our driver data */
+	platform_set_drvdata(pdev, vphydev);
+
+	match = of_match_node(xvphy_of_match, np);
+	if (!match)
+		return -ENODEV;
+
+	if (strncmp(match->compatible, "xlnx,vid-phy-controller", 23) == 0)
+		vphydev->isvphy = 1;
+	else
+		vphydev->isvphy = 0;
+
+	XVphy_ConfigTable[instance].DeviceId = VPHY_DEVICE_ID_BASE + instance;
+	XHdmiphy1_ConfigTable[instance].DeviceId = VPHY_DEVICE_ID_BASE + instance;
+
+	dev_dbg(vphydev->dev,"DT parse start\n");
+	if (vphydev->isvphy)
+		ret = vphy_parse_of(vphydev, &XVphy_ConfigTable[instance]);
+	else
+		ret = vphy_parse_of(vphydev, &XHdmiphy1_ConfigTable[instance]);
+	if (ret) return ret;
+	dev_dbg(vphydev->dev,"DT parse done\n");
+
+	for_each_child_of_node(np, child) {
+		struct xvphy_lane *vphy_lane;
+
+		vphy_lane = devm_kzalloc(&pdev->dev, sizeof(*vphy_lane),
+					 GFP_KERNEL);
+		if (!vphy_lane)
+			return -ENOMEM;
+
+		/* Assign lane number to gtr_phy instance */
+		vphy_lane->lane = index;
+
+		/* Disable lane sharing as default */
+		vphy_lane->share_laneclk = -1;
+
+		if (port >= 4) {
+			dev_err(&pdev->dev, "MAX 4 PHY Lanes are supported\n");
+			return -E2BIG;
+		}
+
+		/* array of pointer to vphy_lane structs */
+		vphydev->lanes[port] = vphy_lane;
+
+		/* create phy device for each lane */
+		phy = devm_phy_create(&pdev->dev, child, &xvphy_phyops);
+		if (IS_ERR(phy)) {
+			ret = PTR_ERR(phy);
+			if (ret == -EPROBE_DEFER)
+				dev_info(&pdev->dev, "xvphy probe deferred\n");
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "failed to create PHY\n");
+			return ret;
+		}
+		/* array of pointer to phy */
+		vphydev->lanes[port]->phy = phy;
+		/* where each phy device has vphy_lane as driver data */
+		phy_set_drvdata(phy, vphydev->lanes[port]);
+		/* and each vphy_lane points back to parent device */
+		vphy_lane->data = vphydev;
+		port++;
+		index++;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	vphydev->iomem = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(vphydev->iomem))
+		return PTR_ERR(vphydev->iomem);
+
+	/* set address in configuration data */
+	XVphy_ConfigTable[instance].BaseAddr = (uintptr_t)vphydev->iomem;
+	XHdmiphy1_ConfigTable[instance].BaseAddr = (uintptr_t)vphydev->iomem;
+
+	vphydev->irq = platform_get_irq(pdev, 0);
+	if (vphydev->irq <= 0) {
+		dev_err(&pdev->dev, "platform_get_irq() failed\n");
+		return vphydev->irq;
+	}
+
+	/* the AXI lite clock is used for the clock rate detector */
+	if (vphydev->isvphy)
+		vphydev->axi_lite_clk = devm_clk_get(&pdev->dev, "vid_phy_axi4lite_aclk");
+	else
+		vphydev->axi_lite_clk = devm_clk_get(&pdev->dev, "axi4lite_aclk");
+	if (IS_ERR(vphydev->axi_lite_clk)) {
+		ret = PTR_ERR(vphydev->axi_lite_clk);
+		vphydev->axi_lite_clk = NULL;
+		if (ret == -EPROBE_DEFER)
+			dev_info(&pdev->dev, "axi-lite-clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "failed to get the axi lite clk.\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(vphydev->axi_lite_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable axi-lite clk\n");
+		return ret;
+	}
+	axi_lite_rate = clk_get_rate(vphydev->axi_lite_clk);
+	dev_dbg(vphydev->dev,"AXI Lite clock rate = %lu Hz\n", axi_lite_rate);
+
+	/* set axi-lite clk in configuration data */
+	XVphy_ConfigTable[instance].AxiLiteClkFreq = axi_lite_rate;
+	XVphy_ConfigTable[instance].DrpClkFreq = axi_lite_rate;
+	XHdmiphy1_ConfigTable[instance].AxiLiteClkFreq = axi_lite_rate;
+	XHdmiphy1_ConfigTable[instance].DrpClkFreq = axi_lite_rate;
+
+	/* dru-clk is used for the nidru block for low res support */
+	if ((vphydev->isvphy && (XVphy_ConfigTable[instance].DruIsPresent == (TRUE))) ||
+		(!vphydev->isvphy && (XHdmiphy1_ConfigTable[instance].DruIsPresent == (TRUE)))) {
+		vphydev->dru_clk = devm_clk_get(&pdev->dev, "dru-clk");
+		if (IS_ERR(vphydev->dru_clk)) {
+			ret = PTR_ERR(vphydev->dru_clk);
+			vphydev->dru_clk = NULL;
+			if (ret == -EPROBE_DEFER)
+				dev_info(&pdev->dev, "dru-clk not ready -EPROBE_DEFER\n");
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "failed to get the nidru clk.\n");
+			return ret;
+		}
+
+		ret = clk_prepare_enable(vphydev->dru_clk);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to enable nidru clk\n");
+			return ret;
+		}
+
+		dru_clk_rate = clk_get_rate(vphydev->dru_clk);
+		dev_dbg(vphydev->dev, "default dru-clk rate = %lu\n", dru_clk_rate);
+		if ((vphydev->isvphy && (dru_clk_rate != XVPHY_DRU_REF_CLK_HZ)) ||
+			(!vphydev->isvphy && (dru_clk_rate != XHDMIPHY1_DRU_REF_CLK_HZ))) {
+
+			if (vphydev->isvphy)
+				ret = clk_set_rate(vphydev->dru_clk, XVPHY_DRU_REF_CLK_HZ);
+			else
+				ret = clk_set_rate(vphydev->dru_clk, XHDMIPHY1_DRU_REF_CLK_HZ);
+
+			if (ret != 0) {
+				dev_err(&pdev->dev, "Cannot set rate : %d\n", ret);
+			}
+			dru_clk_rate = clk_get_rate(vphydev->dru_clk);
+			dev_dbg(vphydev->dev, "ref dru-clk rate = %lu\n", dru_clk_rate);
+		}
+	}
+	else
+	{
+		dev_dbg(vphydev->dev, "DRU is not enabled from device tree\n");
+	}
+
+	provider = devm_of_phy_provider_register(&pdev->dev, xvphy_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(&pdev->dev, "registering provider failed\n");
+			return PTR_ERR(provider);
+	}
+
+	/* Initialize HDMI VPHY */
+	if (vphydev->isvphy)
+		Status = XVphy_Hdmi_CfgInitialize(&vphydev->xvphy, 0/*QuadID*/,
+				&XVphy_ConfigTable[instance]);
+	else
+		Status = XHdmiphy1_Hdmi_CfgInitialize(&vphydev->xgtphy, 0/*QuadID*/,
+				&XHdmiphy1_ConfigTable[instance]);
+	if (Status != XST_SUCCESS) {
+		dev_err(&pdev->dev, "HDMI VPHY initialization error\n");
+		return ENODEV;
+	}
+
+	if (vphydev->isvphy)
+		Data = XVphy_GetVersion(&vphydev->xvphy);
+	else
+		Data = XHdmiphy1_GetVersion(&vphydev->xgtphy);
+	dev_info(vphydev->dev, "VPhy version : %02d.%02d (%04x)\n", ((Data >> 24) & 0xFF),
+			((Data >> 16) & 0xFF), (Data & 0xFFFF));
+
+
+	ret = devm_request_threaded_irq(&pdev->dev, vphydev->irq, xvphy_irq_handler, xvphy_irq_thread,
+			IRQF_TRIGGER_HIGH /*IRQF_SHARED*/, "xilinx-vphy", vphydev/*dev_id*/);
+
+	if (ret) {
+		dev_err(&pdev->dev, "unable to request IRQ %d\n", vphydev->irq);
+		return ret;
+	}
+
+	if (vphydev->isvphy) {
+		dev_dbg(vphydev->dev,"config.DruIsPresent = %d\n", XVphy_ConfigTable[instance].DruIsPresent);
+		if (vphydev->xvphy.Config.DruIsPresent == (TRUE)) {
+			dev_dbg(vphydev->dev,"DRU reference clock frequency %0d Hz\n\r",
+						XVphy_DruGetRefClkFreqHz(&vphydev->xvphy));
+		}
+	} else {
+		dev_dbg(vphydev->dev,"config.DruIsPresent = %d\n", XHdmiphy1_ConfigTable[instance].DruIsPresent);
+		if (vphydev->xgtphy.Config.DruIsPresent == (TRUE)) {
+			dev_info(vphydev->dev,"DRU reference clock frequency %0d Hz\n",
+						XHdmiphy1_DruGetRefClkFreqHz(&vphydev->xgtphy));
+		}
+	}
+
+	dev_info(&pdev->dev, "probe successful\n");
+	/* probe has succeeded for this instance, increment instance index */
+	instance++;
+	return 0;
+}
+
+static int __maybe_unused xvphy_pm_suspend(struct device *dev)
+{
+	struct xvphy_dev *vphydev = dev_get_drvdata(dev);
+	dev_dbg(vphydev->dev, "Vphy suspend function called\n");
+	xvphy_intr_disable(vphydev);
+	return 0;
+}
+
+static int __maybe_unused xvphy_pm_resume(struct device *dev)
+{
+	struct xvphy_dev *vphydev = dev_get_drvdata(dev);
+	dev_dbg(vphydev->dev, "Vphy resume function called\n");
+	xvphy_intr_enable(vphydev);
+	return 0;
+}
+
+static const struct dev_pm_ops xvphy_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xvphy_pm_suspend, xvphy_pm_resume)
+};
+
+static struct platform_driver xvphy_driver = {
+	.probe = xvphy_probe,
+	.driver = {
+		.name = "xilinx-vphy",
+		.of_match_table	= xvphy_of_match,
+		.pm = &xvphy_pm_ops,
+	},
+};
+module_platform_driver(xvphy_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Leon Woestenberg <leon@sidebranch.com>");
+MODULE_DESCRIPTION("Xilinx Vphy / HDMI GT Controller  driver");
+
+/* phy sub-directory is used as a place holder for all shared code for
+   hdmi-rx and hdmi-tx driver. All shared API's need to be exported */
+
+/* Configuration Tables for hdcp */
+XHdcp1x_Config XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES];
+XTmrCtr_Config XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES];
+XHdcp22_Cipher_Config XHdcp22_Cipher_ConfigTable[XPAR_XHDCP22_CIPHER_NUM_INSTANCES];
+XHdcp22_mmult_Config XHdcp22_mmult_ConfigTable[XPAR_XHDCP22_MMULT_NUM_INSTANCES];
+XHdcp22_Rng_Config XHdcp22_Rng_ConfigTable[XPAR_XHDCP22_RNG_NUM_INSTANCES];
+XHdcp22_Rx_Config XHdcp22_Rx_ConfigTable[XPAR_XHDCP22_RX_NUM_INSTANCES];
+XHdcp22_Tx_Config XHdcp22_Tx_ConfigTable[XPAR_XHDCP22_TX_NUM_INSTANCES];
+
+
+/* common functionality shared between RX and TX */
+/* xvidc component */
+EXPORT_SYMBOL_GPL(XVidC_ReportTiming);
+EXPORT_SYMBOL_GPL(XVidC_SetVideoStream);
+EXPORT_SYMBOL_GPL(XVidC_ReportStreamInfo);
+EXPORT_SYMBOL_GPL(XVidC_Set3DVideoStream);
+EXPORT_SYMBOL_GPL(XVidC_GetPixelClockHzByVmId);
+EXPORT_SYMBOL_GPL(XVidC_GetVideoModeIdWBlanking);
+EXPORT_SYMBOL_GPL(XVidC_GetVideoModeId);
+EXPORT_SYMBOL_GPL(XVidC_GetPixelClockHzByHVFr);
+EXPORT_SYMBOL_GPL(XVidC_ShowStreamInfo);
+
+/* Configuration Tables for hdcp */
+EXPORT_SYMBOL_GPL(XHdcp1x_ConfigTable);
+EXPORT_SYMBOL_GPL(XTmrCtr_ConfigTable);
+EXPORT_SYMBOL_GPL(XHdcp22_Cipher_ConfigTable);
+EXPORT_SYMBOL_GPL(XHdcp22_mmult_ConfigTable);
+EXPORT_SYMBOL_GPL(XHdcp22_Rng_ConfigTable);
+EXPORT_SYMBOL_GPL(XHdcp22_Rx_ConfigTable);
+EXPORT_SYMBOL_GPL(XHdcp22_Tx_ConfigTable);
+
+/* Global API's for hdcp key */
+EXPORT_SYMBOL_GPL(XHdcp22Cmn_Sha256Hash);
+EXPORT_SYMBOL_GPL(XHdcp22Cmn_HmacSha256Hash);
+EXPORT_SYMBOL_GPL(XHdcp22Cmn_Aes128Encrypt);
+EXPORT_SYMBOL_GPL(aes256_done);
+EXPORT_SYMBOL_GPL(aes256_init);
+EXPORT_SYMBOL_GPL(aes256_decrypt_ecb);
+
+/* Global API's for xhdcp1x */
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTopologyUpdate);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_LoadPublicCert);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_LoadLc128);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_IsEnabled);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_IsRepeater);
+EXPORT_SYMBOL_GPL(XHdcp1x_GetVersion);
+EXPORT_SYMBOL_GPL(XHdcp1x_CipherIntrHandler);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTopologyField);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsAuthenticated);
+EXPORT_SYMBOL_GPL(XHdcp1x_Info);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetRepeater);
+EXPORT_SYMBOL_GPL(XHdcp1x_ProcessAKsv);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTimerStart);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTimerStop);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsRepeater);
+EXPORT_SYMBOL_GPL(XHdcp1x_SelfTest);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsInWaitforready);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetKeySelect);
+EXPORT_SYMBOL_GPL(XHdcp1x_Reset);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTimerDelay);
+EXPORT_SYMBOL_GPL(XHdcp1x_LookupConfig);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTopology);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsEnabled);
+EXPORT_SYMBOL_GPL(XHdcp1x_Disable);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetDebugLogMsg);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetTopologyKSVList);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsEncrypted);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetCallback);
+EXPORT_SYMBOL_GPL(XHdcp1x_HandleTimeout);
+EXPORT_SYMBOL_GPL(XHdcp1x_Poll);
+EXPORT_SYMBOL_GPL(XHdcp1x_Enable);
+EXPORT_SYMBOL_GPL(XHdcp1x_CfgInitialize);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsInProgress);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetHdmiMode);
+EXPORT_SYMBOL_GPL(XHdcp1x_SetPhysicalState);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsInComputations);
+EXPORT_SYMBOL_GPL(XHdcp1x_EnableBlank);
+EXPORT_SYMBOL_GPL(XHdcp1x_GetTopologyField);
+EXPORT_SYMBOL_GPL(XHdcp1x_DisableEncryption);
+EXPORT_SYMBOL_GPL(XHdcp1x_GetTopology);
+EXPORT_SYMBOL_GPL(XHdcp1x_GetTopologyKSVList);
+EXPORT_SYMBOL_GPL(XHdcp1x_DisableBlank);
+EXPORT_SYMBOL_GPL(XHdcp1x_EnableEncryption);
+EXPORT_SYMBOL_GPL(XHdcp1x_IsDwnstrmCapable);
+EXPORT_SYMBOL_GPL(XHdcp1x_LateInit);
+
+/* Global API's for XTmr */
+EXPORT_SYMBOL_GPL(XTmrCtr_CfgInitialize);
+EXPORT_SYMBOL_GPL(XTmrCtr_IsExpired);
+EXPORT_SYMBOL_GPL(XTmrCtr_Start);
+EXPORT_SYMBOL_GPL(XTmrCtr_InitHw);
+EXPORT_SYMBOL_GPL(XTmrCtr_SetOptions);
+EXPORT_SYMBOL_GPL(XTmrCtr_SetResetValue);
+EXPORT_SYMBOL_GPL(XTmrCtr_SetHandler);
+EXPORT_SYMBOL_GPL(XTmrCtr_InterruptHandler);
+EXPORT_SYMBOL_GPL(XTmrCtr_Offsets);
+EXPORT_SYMBOL_GPL(XTmrCtr_LookupConfig);
+EXPORT_SYMBOL_GPL(XTmrCtr_GetOptions);
+EXPORT_SYMBOL_GPL(XTmrCtr_Stop);
+
+/* Global API's for xhdcp22Rx */
+EXPORT_SYMBOL_GPL(XHdcp22Rx_IsAuthenticated);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetDdcError);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetCallback);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_Info);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetRepeater);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_LogReset);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_Reset);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetTopologyUpdate);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_Poll);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_LogShow);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_CfgInitialize);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_IsInProgress);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_GetTimer);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_Disable);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_LoadPrivateKey);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetTopologyField);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetReadMessageComplete);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_GetContentStreamType);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_LookupConfig);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetWriteMessageAvailable);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetTopology);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_Enable);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetTopologyReceiverIdList);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetLinkError);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_IsEncryptionEnabled);
+EXPORT_SYMBOL_GPL(XHdcp22Rx_SetBroadcast);
+
+/* Global API's for xhdcp22Tx */
+EXPORT_SYMBOL_GPL(XHdcp22Tx_IsInProgress);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_GetTopologyReceiverIdList);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_LoadRevocationTable);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_IsEnabled);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_GetTopologyField);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_Reset);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_SetMessagePollingValue);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_Enable);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_GetTimer);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_Disable);
+EXPORT_SYMBOL_GPL(XHdcp1x_Authenticate);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_DisableEncryption);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_LookupConfig);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_LogReset);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_IsDwnstrmCapable);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_IsEncryptionEnabled);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_SetRepeater);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_Authenticate);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_LoadLc128);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_CfgInitialize);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_Info);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_IsRepeater);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_IsAuthenticated);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_GetTopology);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_DisableBlank);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_GetVersion);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_SetCallback);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_SetContentStreamType);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_EnableBlank);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_LogShow);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_EnableEncryption);
+EXPORT_SYMBOL_GPL(XHdcp22Tx_Poll);
+
+/* Debug */
+EXPORT_SYMBOL_GPL(XDebug_SetDebugBufPrintf);
+EXPORT_SYMBOL_GPL(XDebug_SetDebugPrintf);
+
+/* xhdmic and VSIF component */
+EXPORT_SYMBOL_GPL(XV_HdmiC_VSIF_ParsePacket);
+EXPORT_SYMBOL_GPL(XV_HdmiC_IFAspectRatio_To_XVidC);
+EXPORT_SYMBOL_GPL(XV_HdmiC_ParseGCP);
+EXPORT_SYMBOL_GPL(XVidC_GetVideoModeIdExtensive);
+EXPORT_SYMBOL_GPL(XV_HdmiC_ParseAudioInfoFrame);
+EXPORT_SYMBOL_GPL(XV_HdmiC_ParseAVIInfoFrame);
+EXPORT_SYMBOL_GPL(XV_HdmiC_AudioIF_GeneratePacket);
+EXPORT_SYMBOL_GPL(XV_HdmiC_XVidC_To_IfColorformat);
+EXPORT_SYMBOL_GPL(XV_HdmiC_AVIIF_GeneratePacket);
+EXPORT_SYMBOL_GPL(XV_HdmiC_VSIF_GeneratePacket);
+EXPORT_SYMBOL_GPL(VicTable);
+EXPORT_SYMBOL_GPL(XV_HdmiC_ParseDRMIF);
+EXPORT_SYMBOL_GPL(XV_HdmiC_DRMIF_GeneratePacket);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/aes.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/aes.c
@@ -0,0 +1,1107 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file aes.c
+*
+* This code is the implementation of the AES algorithm and
+* the CTR, CBC, and CCM modes of operation it can be used in.
+* AES is, specified by the NIST in in publication FIPS PUB 197,
+* availible at:
+* - http://csrc.nist.gov/publications/fips/fips197/fips-197.pdf .
+* The CBC and CTR modes of operation are specified by
+* NIST SP 800-38 A, available at:
+* - http://csrc.nist.gov/publications/nistpubs/800-38a/sp800-38a.pdf .
+* The CCM mode of operation is specified by NIST SP80-38 C, available at:
+* - http://csrc.nist.gov/publications/nistpubs/800-38C/SP800-38C_updated-July20_2007.pdf
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+* 1.01  MH   01/28/17 Fixed warnings and errors.
+*</pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files *********************************/
+#include <linux/string.h>
+//#include "stdlib.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+/* This is the specified AES SBox. To look up a substitution value, put the first
+   nibble in the first index (row) and the second nibble in the second index (column). */
+static const u8 Aes_Sbox[16][16] = {
+	{0x63,0x7C,0x77,0x7B,0xF2,0x6B,0x6F,0xC5,0x30,0x01,0x67,0x2B,0xFE,0xD7,0xAB,0x76},
+	{0xCA,0x82,0xC9,0x7D,0xFA,0x59,0x47,0xF0,0xAD,0xD4,0xA2,0xAF,0x9C,0xA4,0x72,0xC0},
+	{0xB7,0xFD,0x93,0x26,0x36,0x3F,0xF7,0xCC,0x34,0xA5,0xE5,0xF1,0x71,0xD8,0x31,0x15},
+	{0x04,0xC7,0x23,0xC3,0x18,0x96,0x05,0x9A,0x07,0x12,0x80,0xE2,0xEB,0x27,0xB2,0x75},
+	{0x09,0x83,0x2C,0x1A,0x1B,0x6E,0x5A,0xA0,0x52,0x3B,0xD6,0xB3,0x29,0xE3,0x2F,0x84},
+	{0x53,0xD1,0x00,0xED,0x20,0xFC,0xB1,0x5B,0x6A,0xCB,0xBE,0x39,0x4A,0x4C,0x58,0xCF},
+	{0xD0,0xEF,0xAA,0xFB,0x43,0x4D,0x33,0x85,0x45,0xF9,0x02,0x7F,0x50,0x3C,0x9F,0xA8},
+	{0x51,0xA3,0x40,0x8F,0x92,0x9D,0x38,0xF5,0xBC,0xB6,0xDA,0x21,0x10,0xFF,0xF3,0xD2},
+	{0xCD,0x0C,0x13,0xEC,0x5F,0x97,0x44,0x17,0xC4,0xA7,0x7E,0x3D,0x64,0x5D,0x19,0x73},
+	{0x60,0x81,0x4F,0xDC,0x22,0x2A,0x90,0x88,0x46,0xEE,0xB8,0x14,0xDE,0x5E,0x0B,0xDB},
+	{0xE0,0x32,0x3A,0x0A,0x49,0x06,0x24,0x5C,0xC2,0xD3,0xAC,0x62,0x91,0x95,0xE4,0x79},
+	{0xE7,0xC8,0x37,0x6D,0x8D,0xD5,0x4E,0xA9,0x6C,0x56,0xF4,0xEA,0x65,0x7A,0xAE,0x08},
+	{0xBA,0x78,0x25,0x2E,0x1C,0xA6,0xB4,0xC6,0xE8,0xDD,0x74,0x1F,0x4B,0xBD,0x8B,0x8A},
+	{0x70,0x3E,0xB5,0x66,0x48,0x03,0xF6,0x0E,0x61,0x35,0x57,0xB9,0x86,0xC1,0x1D,0x9E},
+	{0xE1,0xF8,0x98,0x11,0x69,0xD9,0x8E,0x94,0x9B,0x1E,0x87,0xE9,0xCE,0x55,0x28,0xDF},
+	{0x8C,0xA1,0x89,0x0D,0xBF,0xE6,0x42,0x68,0x41,0x99,0x2D,0x0F,0xB0,0x54,0xBB,0x16}
+};
+
+static const u8 Aes_Invsbox[16][16] = {
+	{0x52,0x09,0x6A,0xD5,0x30,0x36,0xA5,0x38,0xBF,0x40,0xA3,0x9E,0x81,0xF3,0xD7,0xFB},
+	{0x7C,0xE3,0x39,0x82,0x9B,0x2F,0xFF,0x87,0x34,0x8E,0x43,0x44,0xC4,0xDE,0xE9,0xCB},
+	{0x54,0x7B,0x94,0x32,0xA6,0xC2,0x23,0x3D,0xEE,0x4C,0x95,0x0B,0x42,0xFA,0xC3,0x4E},
+	{0x08,0x2E,0xA1,0x66,0x28,0xD9,0x24,0xB2,0x76,0x5B,0xA2,0x49,0x6D,0x8B,0xD1,0x25},
+	{0x72,0xF8,0xF6,0x64,0x86,0x68,0x98,0x16,0xD4,0xA4,0x5C,0xCC,0x5D,0x65,0xB6,0x92},
+	{0x6C,0x70,0x48,0x50,0xFD,0xED,0xB9,0xDA,0x5E,0x15,0x46,0x57,0xA7,0x8D,0x9D,0x84},
+	{0x90,0xD8,0xAB,0x00,0x8C,0xBC,0xD3,0x0A,0xF7,0xE4,0x58,0x05,0xB8,0xB3,0x45,0x06},
+	{0xD0,0x2C,0x1E,0x8F,0xCA,0x3F,0x0F,0x02,0xC1,0xAF,0xBD,0x03,0x01,0x13,0x8A,0x6B},
+	{0x3A,0x91,0x11,0x41,0x4F,0x67,0xDC,0xEA,0x97,0xF2,0xCF,0xCE,0xF0,0xB4,0xE6,0x73},
+	{0x96,0xAC,0x74,0x22,0xE7,0xAD,0x35,0x85,0xE2,0xF9,0x37,0xE8,0x1C,0x75,0xDF,0x6E},
+	{0x47,0xF1,0x1A,0x71,0x1D,0x29,0xC5,0x89,0x6F,0xB7,0x62,0x0E,0xAA,0x18,0xBE,0x1B},
+	{0xFC,0x56,0x3E,0x4B,0xC6,0xD2,0x79,0x20,0x9A,0xDB,0xC0,0xFE,0x78,0xCD,0x5A,0xF4},
+	{0x1F,0xDD,0xA8,0x33,0x88,0x07,0xC7,0x31,0xB1,0x12,0x10,0x59,0x27,0x80,0xEC,0x5F},
+	{0x60,0x51,0x7F,0xA9,0x19,0xB5,0x4A,0x0D,0x2D,0xE5,0x7A,0x9F,0x93,0xC9,0x9C,0xEF},
+	{0xA0,0xE0,0x3B,0x4D,0xAE,0x2A,0xF5,0xB0,0xC8,0xEB,0xBB,0x3C,0x83,0x53,0x99,0x61},
+	{0x17,0x2B,0x04,0x7E,0xBA,0x77,0xD6,0x26,0xE1,0x69,0x14,0x63,0x55,0x21,0x0C,0x7D}
+};
+
+/* This table stores pre-calculated values for all possible GF(2^8) calculations.This
+   table is only used by the (Inv)MixColumns steps.
+   USAGE: The second index (column) is the coefficient of multiplication. Only 7 different
+   coefficients are used: 0x01, 0x02, 0x03, 0x09, 0x0b, 0x0d, 0x0e, but multiplication by
+   1 is negligible leaving only 6 coefficients. Each column of the table is devoted to one
+   of these coefficients, in the ascending order of value, from values 0x00 to 0xFF. */
+static const u8 Aes_GfMul[256][6] = {
+	{0x00,0x00,0x00,0x00,0x00,0x00},{0x02,0x03,0x09,0x0b,0x0d,0x0e},
+	{0x04,0x06,0x12,0x16,0x1a,0x1c},{0x06,0x05,0x1b,0x1d,0x17,0x12},
+	{0x08,0x0c,0x24,0x2c,0x34,0x38},{0x0a,0x0f,0x2d,0x27,0x39,0x36},
+	{0x0c,0x0a,0x36,0x3a,0x2e,0x24},{0x0e,0x09,0x3f,0x31,0x23,0x2a},
+	{0x10,0x18,0x48,0x58,0x68,0x70},{0x12,0x1b,0x41,0x53,0x65,0x7e},
+	{0x14,0x1e,0x5a,0x4e,0x72,0x6c},{0x16,0x1d,0x53,0x45,0x7f,0x62},
+	{0x18,0x14,0x6c,0x74,0x5c,0x48},{0x1a,0x17,0x65,0x7f,0x51,0x46},
+	{0x1c,0x12,0x7e,0x62,0x46,0x54},{0x1e,0x11,0x77,0x69,0x4b,0x5a},
+	{0x20,0x30,0x90,0xb0,0xd0,0xe0},{0x22,0x33,0x99,0xbb,0xdd,0xee},
+	{0x24,0x36,0x82,0xa6,0xca,0xfc},{0x26,0x35,0x8b,0xad,0xc7,0xf2},
+	{0x28,0x3c,0xb4,0x9c,0xe4,0xd8},{0x2a,0x3f,0xbd,0x97,0xe9,0xd6},
+	{0x2c,0x3a,0xa6,0x8a,0xfe,0xc4},{0x2e,0x39,0xaf,0x81,0xf3,0xca},
+	{0x30,0x28,0xd8,0xe8,0xb8,0x90},{0x32,0x2b,0xd1,0xe3,0xb5,0x9e},
+	{0x34,0x2e,0xca,0xfe,0xa2,0x8c},{0x36,0x2d,0xc3,0xf5,0xaf,0x82},
+	{0x38,0x24,0xfc,0xc4,0x8c,0xa8},{0x3a,0x27,0xf5,0xcf,0x81,0xa6},
+	{0x3c,0x22,0xee,0xd2,0x96,0xb4},{0x3e,0x21,0xe7,0xd9,0x9b,0xba},
+	{0x40,0x60,0x3b,0x7b,0xbb,0xdb},{0x42,0x63,0x32,0x70,0xb6,0xd5},
+	{0x44,0x66,0x29,0x6d,0xa1,0xc7},{0x46,0x65,0x20,0x66,0xac,0xc9},
+	{0x48,0x6c,0x1f,0x57,0x8f,0xe3},{0x4a,0x6f,0x16,0x5c,0x82,0xed},
+	{0x4c,0x6a,0x0d,0x41,0x95,0xff},{0x4e,0x69,0x04,0x4a,0x98,0xf1},
+	{0x50,0x78,0x73,0x23,0xd3,0xab},{0x52,0x7b,0x7a,0x28,0xde,0xa5},
+	{0x54,0x7e,0x61,0x35,0xc9,0xb7},{0x56,0x7d,0x68,0x3e,0xc4,0xb9},
+	{0x58,0x74,0x57,0x0f,0xe7,0x93},{0x5a,0x77,0x5e,0x04,0xea,0x9d},
+	{0x5c,0x72,0x45,0x19,0xfd,0x8f},{0x5e,0x71,0x4c,0x12,0xf0,0x81},
+	{0x60,0x50,0xab,0xcb,0x6b,0x3b},{0x62,0x53,0xa2,0xc0,0x66,0x35},
+	{0x64,0x56,0xb9,0xdd,0x71,0x27},{0x66,0x55,0xb0,0xd6,0x7c,0x29},
+	{0x68,0x5c,0x8f,0xe7,0x5f,0x03},{0x6a,0x5f,0x86,0xec,0x52,0x0d},
+	{0x6c,0x5a,0x9d,0xf1,0x45,0x1f},{0x6e,0x59,0x94,0xfa,0x48,0x11},
+	{0x70,0x48,0xe3,0x93,0x03,0x4b},{0x72,0x4b,0xea,0x98,0x0e,0x45},
+	{0x74,0x4e,0xf1,0x85,0x19,0x57},{0x76,0x4d,0xf8,0x8e,0x14,0x59},
+	{0x78,0x44,0xc7,0xbf,0x37,0x73},{0x7a,0x47,0xce,0xb4,0x3a,0x7d},
+	{0x7c,0x42,0xd5,0xa9,0x2d,0x6f},{0x7e,0x41,0xdc,0xa2,0x20,0x61},
+	{0x80,0xc0,0x76,0xf6,0x6d,0xad},{0x82,0xc3,0x7f,0xfd,0x60,0xa3},
+	{0x84,0xc6,0x64,0xe0,0x77,0xb1},{0x86,0xc5,0x6d,0xeb,0x7a,0xbf},
+	{0x88,0xcc,0x52,0xda,0x59,0x95},{0x8a,0xcf,0x5b,0xd1,0x54,0x9b},
+	{0x8c,0xca,0x40,0xcc,0x43,0x89},{0x8e,0xc9,0x49,0xc7,0x4e,0x87},
+	{0x90,0xd8,0x3e,0xae,0x05,0xdd},{0x92,0xdb,0x37,0xa5,0x08,0xd3},
+	{0x94,0xde,0x2c,0xb8,0x1f,0xc1},{0x96,0xdd,0x25,0xb3,0x12,0xcf},
+	{0x98,0xd4,0x1a,0x82,0x31,0xe5},{0x9a,0xd7,0x13,0x89,0x3c,0xeb},
+	{0x9c,0xd2,0x08,0x94,0x2b,0xf9},{0x9e,0xd1,0x01,0x9f,0x26,0xf7},
+	{0xa0,0xf0,0xe6,0x46,0xbd,0x4d},{0xa2,0xf3,0xef,0x4d,0xb0,0x43},
+	{0xa4,0xf6,0xf4,0x50,0xa7,0x51},{0xa6,0xf5,0xfd,0x5b,0xaa,0x5f},
+	{0xa8,0xfc,0xc2,0x6a,0x89,0x75},{0xaa,0xff,0xcb,0x61,0x84,0x7b},
+	{0xac,0xfa,0xd0,0x7c,0x93,0x69},{0xae,0xf9,0xd9,0x77,0x9e,0x67},
+	{0xb0,0xe8,0xae,0x1e,0xd5,0x3d},{0xb2,0xeb,0xa7,0x15,0xd8,0x33},
+	{0xb4,0xee,0xbc,0x08,0xcf,0x21},{0xb6,0xed,0xb5,0x03,0xc2,0x2f},
+	{0xb8,0xe4,0x8a,0x32,0xe1,0x05},{0xba,0xe7,0x83,0x39,0xec,0x0b},
+	{0xbc,0xe2,0x98,0x24,0xfb,0x19},{0xbe,0xe1,0x91,0x2f,0xf6,0x17},
+	{0xc0,0xa0,0x4d,0x8d,0xd6,0x76},{0xc2,0xa3,0x44,0x86,0xdb,0x78},
+	{0xc4,0xa6,0x5f,0x9b,0xcc,0x6a},{0xc6,0xa5,0x56,0x90,0xc1,0x64},
+	{0xc8,0xac,0x69,0xa1,0xe2,0x4e},{0xca,0xaf,0x60,0xaa,0xef,0x40},
+	{0xcc,0xaa,0x7b,0xb7,0xf8,0x52},{0xce,0xa9,0x72,0xbc,0xf5,0x5c},
+	{0xd0,0xb8,0x05,0xd5,0xbe,0x06},{0xd2,0xbb,0x0c,0xde,0xb3,0x08},
+	{0xd4,0xbe,0x17,0xc3,0xa4,0x1a},{0xd6,0xbd,0x1e,0xc8,0xa9,0x14},
+	{0xd8,0xb4,0x21,0xf9,0x8a,0x3e},{0xda,0xb7,0x28,0xf2,0x87,0x30},
+	{0xdc,0xb2,0x33,0xef,0x90,0x22},{0xde,0xb1,0x3a,0xe4,0x9d,0x2c},
+	{0xe0,0x90,0xdd,0x3d,0x06,0x96},{0xe2,0x93,0xd4,0x36,0x0b,0x98},
+	{0xe4,0x96,0xcf,0x2b,0x1c,0x8a},{0xe6,0x95,0xc6,0x20,0x11,0x84},
+	{0xe8,0x9c,0xf9,0x11,0x32,0xae},{0xea,0x9f,0xf0,0x1a,0x3f,0xa0},
+	{0xec,0x9a,0xeb,0x07,0x28,0xb2},{0xee,0x99,0xe2,0x0c,0x25,0xbc},
+	{0xf0,0x88,0x95,0x65,0x6e,0xe6},{0xf2,0x8b,0x9c,0x6e,0x63,0xe8},
+	{0xf4,0x8e,0x87,0x73,0x74,0xfa},{0xf6,0x8d,0x8e,0x78,0x79,0xf4},
+	{0xf8,0x84,0xb1,0x49,0x5a,0xde},{0xfa,0x87,0xb8,0x42,0x57,0xd0},
+	{0xfc,0x82,0xa3,0x5f,0x40,0xc2},{0xfe,0x81,0xaa,0x54,0x4d,0xcc},
+	{0x1b,0x9b,0xec,0xf7,0xda,0x41},{0x19,0x98,0xe5,0xfc,0xd7,0x4f},
+	{0x1f,0x9d,0xfe,0xe1,0xc0,0x5d},{0x1d,0x9e,0xf7,0xea,0xcd,0x53},
+	{0x13,0x97,0xc8,0xdb,0xee,0x79},{0x11,0x94,0xc1,0xd0,0xe3,0x77},
+	{0x17,0x91,0xda,0xcd,0xf4,0x65},{0x15,0x92,0xd3,0xc6,0xf9,0x6b},
+	{0x0b,0x83,0xa4,0xaf,0xb2,0x31},{0x09,0x80,0xad,0xa4,0xbf,0x3f},
+	{0x0f,0x85,0xb6,0xb9,0xa8,0x2d},{0x0d,0x86,0xbf,0xb2,0xa5,0x23},
+	{0x03,0x8f,0x80,0x83,0x86,0x09},{0x01,0x8c,0x89,0x88,0x8b,0x07},
+	{0x07,0x89,0x92,0x95,0x9c,0x15},{0x05,0x8a,0x9b,0x9e,0x91,0x1b},
+	{0x3b,0xab,0x7c,0x47,0x0a,0xa1},{0x39,0xa8,0x75,0x4c,0x07,0xaf},
+	{0x3f,0xad,0x6e,0x51,0x10,0xbd},{0x3d,0xae,0x67,0x5a,0x1d,0xb3},
+	{0x33,0xa7,0x58,0x6b,0x3e,0x99},{0x31,0xa4,0x51,0x60,0x33,0x97},
+	{0x37,0xa1,0x4a,0x7d,0x24,0x85},{0x35,0xa2,0x43,0x76,0x29,0x8b},
+	{0x2b,0xb3,0x34,0x1f,0x62,0xd1},{0x29,0xb0,0x3d,0x14,0x6f,0xdf},
+	{0x2f,0xb5,0x26,0x09,0x78,0xcd},{0x2d,0xb6,0x2f,0x02,0x75,0xc3},
+	{0x23,0xbf,0x10,0x33,0x56,0xe9},{0x21,0xbc,0x19,0x38,0x5b,0xe7},
+	{0x27,0xb9,0x02,0x25,0x4c,0xf5},{0x25,0xba,0x0b,0x2e,0x41,0xfb},
+	{0x5b,0xfb,0xd7,0x8c,0x61,0x9a},{0x59,0xf8,0xde,0x87,0x6c,0x94},
+	{0x5f,0xfd,0xc5,0x9a,0x7b,0x86},{0x5d,0xfe,0xcc,0x91,0x76,0x88},
+	{0x53,0xf7,0xf3,0xa0,0x55,0xa2},{0x51,0xf4,0xfa,0xab,0x58,0xac},
+	{0x57,0xf1,0xe1,0xb6,0x4f,0xbe},{0x55,0xf2,0xe8,0xbd,0x42,0xb0},
+	{0x4b,0xe3,0x9f,0xd4,0x09,0xea},{0x49,0xe0,0x96,0xdf,0x04,0xe4},
+	{0x4f,0xe5,0x8d,0xc2,0x13,0xf6},{0x4d,0xe6,0x84,0xc9,0x1e,0xf8},
+	{0x43,0xef,0xbb,0xf8,0x3d,0xd2},{0x41,0xec,0xb2,0xf3,0x30,0xdc},
+	{0x47,0xe9,0xa9,0xee,0x27,0xce},{0x45,0xea,0xa0,0xe5,0x2a,0xc0},
+	{0x7b,0xcb,0x47,0x3c,0xb1,0x7a},{0x79,0xc8,0x4e,0x37,0xbc,0x74},
+	{0x7f,0xcd,0x55,0x2a,0xab,0x66},{0x7d,0xce,0x5c,0x21,0xa6,0x68},
+	{0x73,0xc7,0x63,0x10,0x85,0x42},{0x71,0xc4,0x6a,0x1b,0x88,0x4c},
+	{0x77,0xc1,0x71,0x06,0x9f,0x5e},{0x75,0xc2,0x78,0x0d,0x92,0x50},
+	{0x6b,0xd3,0x0f,0x64,0xd9,0x0a},{0x69,0xd0,0x06,0x6f,0xd4,0x04},
+	{0x6f,0xd5,0x1d,0x72,0xc3,0x16},{0x6d,0xd6,0x14,0x79,0xce,0x18},
+	{0x63,0xdf,0x2b,0x48,0xed,0x32},{0x61,0xdc,0x22,0x43,0xe0,0x3c},
+	{0x67,0xd9,0x39,0x5e,0xf7,0x2e},{0x65,0xda,0x30,0x55,0xfa,0x20},
+	{0x9b,0x5b,0x9a,0x01,0xb7,0xec},{0x99,0x58,0x93,0x0a,0xba,0xe2},
+	{0x9f,0x5d,0x88,0x17,0xad,0xf0},{0x9d,0x5e,0x81,0x1c,0xa0,0xfe},
+	{0x93,0x57,0xbe,0x2d,0x83,0xd4},{0x91,0x54,0xb7,0x26,0x8e,0xda},
+	{0x97,0x51,0xac,0x3b,0x99,0xc8},{0x95,0x52,0xa5,0x30,0x94,0xc6},
+	{0x8b,0x43,0xd2,0x59,0xdf,0x9c},{0x89,0x40,0xdb,0x52,0xd2,0x92},
+	{0x8f,0x45,0xc0,0x4f,0xc5,0x80},{0x8d,0x46,0xc9,0x44,0xc8,0x8e},
+	{0x83,0x4f,0xf6,0x75,0xeb,0xa4},{0x81,0x4c,0xff,0x7e,0xe6,0xaa},
+	{0x87,0x49,0xe4,0x63,0xf1,0xb8},{0x85,0x4a,0xed,0x68,0xfc,0xb6},
+	{0xbb,0x6b,0x0a,0xb1,0x67,0x0c},{0xb9,0x68,0x03,0xba,0x6a,0x02},
+	{0xbf,0x6d,0x18,0xa7,0x7d,0x10},{0xbd,0x6e,0x11,0xac,0x70,0x1e},
+	{0xb3,0x67,0x2e,0x9d,0x53,0x34},{0xb1,0x64,0x27,0x96,0x5e,0x3a},
+	{0xb7,0x61,0x3c,0x8b,0x49,0x28},{0xb5,0x62,0x35,0x80,0x44,0x26},
+	{0xab,0x73,0x42,0xe9,0x0f,0x7c},{0xa9,0x70,0x4b,0xe2,0x02,0x72},
+	{0xaf,0x75,0x50,0xff,0x15,0x60},{0xad,0x76,0x59,0xf4,0x18,0x6e},
+	{0xa3,0x7f,0x66,0xc5,0x3b,0x44},{0xa1,0x7c,0x6f,0xce,0x36,0x4a},
+	{0xa7,0x79,0x74,0xd3,0x21,0x58},{0xa5,0x7a,0x7d,0xd8,0x2c,0x56},
+	{0xdb,0x3b,0xa1,0x7a,0x0c,0x37},{0xd9,0x38,0xa8,0x71,0x01,0x39},
+	{0xdf,0x3d,0xb3,0x6c,0x16,0x2b},{0xdd,0x3e,0xba,0x67,0x1b,0x25},
+	{0xd3,0x37,0x85,0x56,0x38,0x0f},{0xd1,0x34,0x8c,0x5d,0x35,0x01},
+	{0xd7,0x31,0x97,0x40,0x22,0x13},{0xd5,0x32,0x9e,0x4b,0x2f,0x1d},
+	{0xcb,0x23,0xe9,0x22,0x64,0x47},{0xc9,0x20,0xe0,0x29,0x69,0x49},
+	{0xcf,0x25,0xfb,0x34,0x7e,0x5b},{0xcd,0x26,0xf2,0x3f,0x73,0x55},
+	{0xc3,0x2f,0xcd,0x0e,0x50,0x7f},{0xc1,0x2c,0xc4,0x05,0x5d,0x71},
+	{0xc7,0x29,0xdf,0x18,0x4a,0x63},{0xc5,0x2a,0xd6,0x13,0x47,0x6d},
+	{0xfb,0x0b,0x31,0xca,0xdc,0xd7},{0xf9,0x08,0x38,0xc1,0xd1,0xd9},
+	{0xff,0x0d,0x23,0xdc,0xc6,0xcb},{0xfd,0x0e,0x2a,0xd7,0xcb,0xc5},
+	{0xf3,0x07,0x15,0xe6,0xe8,0xef},{0xf1,0x04,0x1c,0xed,0xe5,0xe1},
+	{0xf7,0x01,0x07,0xf0,0xf2,0xf3},{0xf5,0x02,0x0e,0xfb,0xff,0xfd},
+	{0xeb,0x13,0x79,0x92,0xb4,0xa7},{0xe9,0x10,0x70,0x99,0xb9,0xa9},
+	{0xef,0x15,0x6b,0x84,0xae,0xbb},{0xed,0x16,0x62,0x8f,0xa3,0xb5},
+	{0xe3,0x1f,0x5d,0xbe,0x80,0x9f},{0xe1,0x1c,0x54,0xb5,0x8d,0x91},
+	{0xe7,0x19,0x4f,0xa8,0x9a,0x83},{0xe5,0x1a,0x46,0xa3,0x97,0x8d}
+};
+
+/***************** Macros (Inline Functions) Definitions *********************/
+// The least significant byte of the word is rotated to the end.
+#define AES_BLOCK_SIZE 16 /* AES operates on 16 bytes at a time */
+#define KE_ROTWORD(x) (((x) << 8) | ((x) >> 24))
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+static u32  AesSubWord(u32 Word);
+static void AesKeySetup(const u8 Key[], u32 W[], int KeySizeBits);
+static void AesAddRoundKey(u8 State[][4], const u32 W[]);
+static void AesSubBytes(u8 State[][4]);
+static void AesInvSubBytes(u8 State[][4]);
+static void AesShiftRows(u8 State[][4]);
+static void AesInvShiftRows(u8 State[][4]);
+static void AesMixColumns(u8 State[][4]);
+static void AesInvMixColumns(u8 State[][4]);
+static void AesEncrypt(const u8 In[], u8 Out[], const u32 Key[], int KeySize);
+static void AesDecrypt(const u8 In[], u8 Out[], const u32 Key[], int KeySize);
+#ifdef AES_CIPHER_CTR_MODE
+static void Xor(u8 *C, const u8 *A, const u8 *B, u32 Size);
+static void AesIncrementIv(u8 Iv[], int CounterSize);
+static void AesEncryptCtr(const u8 In[], size_t InLen, u8 Out[],
+								  const u32 Key[], int KeySize, const u8 Iv[]);
+static void AesDecryptCtr(const u8 In[], size_t InLen, u8 Out[],
+								 const u32 Key[], int KeySize, const u8 Iv[]);
+#endif
+
+/************************** Variable Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function encrypts 128 bits data with a key of size 128 bits.
+*
+* @param	Input is the 16 byte plaintext
+* @param	Key is the user supplied input key
+* @param	Output is the 16 byte ciphertext
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp22Cmn_Aes128Encrypt(const u8 *Data, const u8 *Key, u8 *Output)
+{
+	u32 KeySchedule[60];
+
+	/* Setup the AES internal key */
+	AesKeySetup(Key, KeySchedule, 128);
+	/* Encrypt 128-bits*/
+	AesEncrypt(Data, Output, KeySchedule, 128);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function encrypts 128 bits data with a key of size 128 bits.
+*
+* @param	Input is the 16 byte ciphertext
+* @param	Key is the user supplied input key
+* @param	Output is the 16 byte plaintext
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp22Cmn_Aes128Decrypt(const u8 *Data, const u8 *Key, u8 *Output)
+{
+	u32 KeySchedule[60];
+
+	/* Setup the AES internal key */
+	AesKeySetup(Key, KeySchedule, 128);
+	/* Encrypt 128-bits*/
+	AesDecrypt(Data, Output, KeySchedule, 128);
+}
+
+#ifdef AES_CIPHER_CTR_MODE
+/****************************************************************************/
+/**
+*
+* This function calculates an XOR over each element of two equally sized
+* arrays.
+*
+* C = A ^ B.
+*
+* @param	C is the XOR of the input arrays.
+* @param    A is the input byte array.
+* @param    B is the input byte array.
+* @param    Size is the length of the input byte arrays.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+static void Xor(u8 *C, const u8 *A, const u8 *B, u32 Size)
+{
+	while(Size--)
+	{
+		C[Size] = A[Size] ^ B[Size];
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+*
+* This function substitutes a word using the AES S-Box.
+*
+* @param	Word to substitute.
+*
+* @return	Transformation word.
+*
+* @note		None.
+*
+******************************************************************************/
+static u32 AesSubWord(u32 Word)
+{
+	unsigned int result;
+
+	result = (int)Aes_Sbox[(Word >> 4) & 0x0000000F][Word & 0x0000000F];
+	result += (int)Aes_Sbox[(Word >> 12) & 0x0000000F][(Word >> 8) & 0x0000000F] << 8;
+	result += (int)Aes_Sbox[(Word >> 20) & 0x0000000F][(Word >> 16) & 0x0000000F] << 16;
+	result += (int)Aes_Sbox[(Word >> 28) & 0x0000000F][(Word >> 24) & 0x0000000F] << 24;
+	return(result);
+}
+
+/*****************************************************************************/
+/**
+*
+* Performs the action of generating the keys that will be used in every round of
+* encryption.
+*
+* @param	Key is the user-supplied input key.
+* @param	W is the output key schedule.
+* @param	KeySize is the length in bits of "Key", must be 128, 192, or 256.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesKeySetup(const u8 Key[], u32 W[], int KeySizeBits)
+{
+	int Nb=4, Nr, Nk, Idx;
+	u32 Temp, Rcon[]={0x01000000,0x02000000,0x04000000,0x08000000,0x10000000,0x20000000,
+	                  0x40000000,0x80000000,0x1b000000,0x36000000,0x6c000000,0xd8000000,
+	                  0xab000000,0x4d000000,0x9a000000};
+
+	switch (KeySizeBits) {
+		case 128: Nr = 10; Nk = 4; break;
+		case 192: Nr = 12; Nk = 6; break;
+		case 256: Nr = 14; Nk = 8; break;
+		default: return;
+	}
+
+	for (Idx=0; Idx < Nk; ++Idx) {
+		W[Idx] = ((Key[4 * Idx]) << 24) | ((Key[4 * Idx + 1]) << 16) |
+				   ((Key[4 * Idx + 2]) << 8) | ((Key[4 * Idx + 3]));
+	}
+
+	for (Idx = Nk; Idx < Nb * (Nr+1); ++Idx) {
+		Temp = W[Idx - 1];
+		if ((Idx % Nk) == 0)
+			Temp = AesSubWord(KE_ROTWORD(Temp)) ^ Rcon[(Idx-1)/Nk];
+		else if (Nk > 6 && (Idx % Nk) == 4)
+			Temp = AesSubWord(Temp);
+		W[Idx] = W[Idx-Nk] ^ Temp;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* Performs the AddRoundKey step.
+* Each round has its own pre-generated 16-byte key in the form of 4 integers W.
+* Each integer is XOR'd by one column of the state.
+* Also performs the job of InvAddRoundKey(); since the function is a simple XOR process,
+* it is its own inverse.
+*
+* @param	State are the statevalues of the AES conversion
+* @param	W are the 4 integers.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesAddRoundKey(u8 State[][4], const u32 w[])
+{
+	u8 subkey[4];
+
+	// memcpy(subkey,&w[Idx],4); // Not accurate for big endian machines
+	// Subkey 1
+	subkey[0] = w[0] >> 24;
+	subkey[1] = w[0] >> 16;
+	subkey[2] = w[0] >> 8;
+	subkey[3] = w[0];
+	State[0][0] ^= subkey[0];
+	State[1][0] ^= subkey[1];
+	State[2][0] ^= subkey[2];
+	State[3][0] ^= subkey[3];
+	// Subkey 2
+	subkey[0] = w[1] >> 24;
+	subkey[1] = w[1] >> 16;
+	subkey[2] = w[1] >> 8;
+	subkey[3] = w[1];
+	State[0][1] ^= subkey[0];
+	State[1][1] ^= subkey[1];
+	State[2][1] ^= subkey[2];
+	State[3][1] ^= subkey[3];
+	// Subkey 3
+	subkey[0] = w[2] >> 24;
+	subkey[1] = w[2] >> 16;
+	subkey[2] = w[2] >> 8;
+	subkey[3] = w[2];
+	State[0][2] ^= subkey[0];
+	State[1][2] ^= subkey[1];
+	State[2][2] ^= subkey[2];
+	State[3][2] ^= subkey[3];
+	// Subkey 4
+	subkey[0] = w[3] >> 24;
+	subkey[1] = w[3] >> 16;
+	subkey[2] = w[3] >> 8;
+	subkey[3] = w[3];
+	State[0][3] ^= subkey[0];
+	State[1][3] ^= subkey[1];
+	State[2][3] ^= subkey[2];
+	State[3][3] ^= subkey[3];
+}
+
+/*****************************************************************************/
+/**
+*
+* Performs the SubBytes step. All bytes in the State are substituted with a
+* pre-calculated value from a lookup table.
+*
+* @param	State are the statevalues of the AES conversion.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesSubBytes(u8 State[][4])
+{
+	State[0][0] = Aes_Sbox[State[0][0] >> 4][State[0][0] & 0x0F];
+	State[0][1] = Aes_Sbox[State[0][1] >> 4][State[0][1] & 0x0F];
+	State[0][2] = Aes_Sbox[State[0][2] >> 4][State[0][2] & 0x0F];
+	State[0][3] = Aes_Sbox[State[0][3] >> 4][State[0][3] & 0x0F];
+	State[1][0] = Aes_Sbox[State[1][0] >> 4][State[1][0] & 0x0F];
+	State[1][1] = Aes_Sbox[State[1][1] >> 4][State[1][1] & 0x0F];
+	State[1][2] = Aes_Sbox[State[1][2] >> 4][State[1][2] & 0x0F];
+	State[1][3] = Aes_Sbox[State[1][3] >> 4][State[1][3] & 0x0F];
+	State[2][0] = Aes_Sbox[State[2][0] >> 4][State[2][0] & 0x0F];
+	State[2][1] = Aes_Sbox[State[2][1] >> 4][State[2][1] & 0x0F];
+	State[2][2] = Aes_Sbox[State[2][2] >> 4][State[2][2] & 0x0F];
+	State[2][3] = Aes_Sbox[State[2][3] >> 4][State[2][3] & 0x0F];
+	State[3][0] = Aes_Sbox[State[3][0] >> 4][State[3][0] & 0x0F];
+	State[3][1] = Aes_Sbox[State[3][1] >> 4][State[3][1] & 0x0F];
+	State[3][2] = Aes_Sbox[State[3][2] >> 4][State[3][2] & 0x0F];
+	State[3][3] = Aes_Sbox[State[3][3] >> 4][State[3][3] & 0x0F];
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Performs the inverted substates step.
+*
+* @param	State are the statevalues of the AES conversion
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesInvSubBytes(u8 State[][4])
+{
+	State[0][0] = Aes_Invsbox[State[0][0] >> 4][State[0][0] & 0x0F];
+	State[0][1] = Aes_Invsbox[State[0][1] >> 4][State[0][1] & 0x0F];
+	State[0][2] = Aes_Invsbox[State[0][2] >> 4][State[0][2] & 0x0F];
+	State[0][3] = Aes_Invsbox[State[0][3] >> 4][State[0][3] & 0x0F];
+	State[1][0] = Aes_Invsbox[State[1][0] >> 4][State[1][0] & 0x0F];
+	State[1][1] = Aes_Invsbox[State[1][1] >> 4][State[1][1] & 0x0F];
+	State[1][2] = Aes_Invsbox[State[1][2] >> 4][State[1][2] & 0x0F];
+	State[1][3] = Aes_Invsbox[State[1][3] >> 4][State[1][3] & 0x0F];
+	State[2][0] = Aes_Invsbox[State[2][0] >> 4][State[2][0] & 0x0F];
+	State[2][1] = Aes_Invsbox[State[2][1] >> 4][State[2][1] & 0x0F];
+	State[2][2] = Aes_Invsbox[State[2][2] >> 4][State[2][2] & 0x0F];
+	State[2][3] = Aes_Invsbox[State[2][3] >> 4][State[2][3] & 0x0F];
+	State[3][0] = Aes_Invsbox[State[3][0] >> 4][State[3][0] & 0x0F];
+	State[3][1] = Aes_Invsbox[State[3][1] >> 4][State[3][1] & 0x0F];
+	State[3][2] = Aes_Invsbox[State[3][2] >> 4][State[3][2] & 0x0F];
+	State[3][3] = Aes_Invsbox[State[3][3] >> 4][State[3][3] & 0x0F];
+}
+
+/*****************************************************************************/
+/**
+*
+* This function erforms the ShiftRows step. All rows are shifted cylindrically
+* to the left.
+*
+* @param	State are the statevalues of the AES conversion.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesShiftRows(u8 State[][4])
+{
+	int t;
+
+	// Shift left by 1
+	t = State[1][0];
+	State[1][0] = State[1][1];
+	State[1][1] = State[1][2];
+	State[1][2] = State[1][3];
+	State[1][3] = t;
+	// Shift left by 2
+	t = State[2][0];
+	State[2][0] = State[2][2];
+	State[2][2] = t;
+	t = State[2][1];
+	State[2][1] = State[2][3];
+	State[2][3] = t;
+	// Shift left by 3
+	t = State[3][0];
+	State[3][0] = State[3][3];
+	State[3][3] = State[3][2];
+	State[3][2] = State[3][1];
+	State[3][1] = t;
+}
+
+/*****************************************************************************/
+/**
+*
+* All rows are shifted cylindrically to the right.
+*
+* @param	State are the statevalues of the AES conversion.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesInvShiftRows(u8 State[][4])
+{
+	int t;
+
+	// Shift right by 1
+	t = State[1][3];
+	State[1][3] = State[1][2];
+	State[1][2] = State[1][1];
+	State[1][1] = State[1][0];
+	State[1][0] = t;
+	// Shift right by 2
+	t = State[2][3];
+	State[2][3] = State[2][1];
+	State[2][1] = t;
+	t = State[2][2];
+	State[2][2] = State[2][0];
+	State[2][0] = t;
+	// Shift right by 3
+	t = State[3][3];
+	State[3][3] = State[3][0];
+	State[3][0] = State[3][1];
+	State[3][1] = State[3][2];
+	State[3][2] = t;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Performs the MixColums step.
+* The State is multiplied by itself using matrix
+* multiplication in a Galios Field 2^8. All multiplication is pre-computed in a table.
+* Addition is equivilent to XOR. (Must always make a copy of the column as the original
+* values will be destoyed.)
+*
+* @param	State are the statevalues of the AES conversion.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesMixColumns(u8 State[][4])
+{
+	u8 Col[4];
+
+	// Column 1
+	Col[0] = State[0][0];
+	Col[1] = State[1][0];
+	Col[2] = State[2][0];
+	Col[3] = State[3][0];
+	State[0][0] = Aes_GfMul[Col[0]][0];
+	State[0][0] ^= Aes_GfMul[Col[1]][1];
+	State[0][0] ^= Col[2];
+	State[0][0] ^= Col[3];
+	State[1][0] = Col[0];
+	State[1][0] ^= Aes_GfMul[Col[1]][0];
+	State[1][0] ^= Aes_GfMul[Col[2]][1];
+	State[1][0] ^= Col[3];
+	State[2][0] = Col[0];
+	State[2][0] ^= Col[1];
+	State[2][0] ^= Aes_GfMul[Col[2]][0];
+	State[2][0] ^= Aes_GfMul[Col[3]][1];
+	State[3][0] = Aes_GfMul[Col[0]][1];
+	State[3][0] ^= Col[1];
+	State[3][0] ^= Col[2];
+	State[3][0] ^= Aes_GfMul[Col[3]][0];
+	// Column 2
+	Col[0] = State[0][1];
+	Col[1] = State[1][1];
+	Col[2] = State[2][1];
+	Col[3] = State[3][1];
+	State[0][1] = Aes_GfMul[Col[0]][0];
+	State[0][1] ^= Aes_GfMul[Col[1]][1];
+	State[0][1] ^= Col[2];
+	State[0][1] ^= Col[3];
+	State[1][1] = Col[0];
+	State[1][1] ^= Aes_GfMul[Col[1]][0];
+	State[1][1] ^= Aes_GfMul[Col[2]][1];
+	State[1][1] ^= Col[3];
+	State[2][1] = Col[0];
+	State[2][1] ^= Col[1];
+	State[2][1] ^= Aes_GfMul[Col[2]][0];
+	State[2][1] ^= Aes_GfMul[Col[3]][1];
+	State[3][1] = Aes_GfMul[Col[0]][1];
+	State[3][1] ^= Col[1];
+	State[3][1] ^= Col[2];
+	State[3][1] ^= Aes_GfMul[Col[3]][0];
+	// Column 3
+	Col[0] = State[0][2];
+	Col[1] = State[1][2];
+	Col[2] = State[2][2];
+	Col[3] = State[3][2];
+	State[0][2] = Aes_GfMul[Col[0]][0];
+	State[0][2] ^= Aes_GfMul[Col[1]][1];
+	State[0][2] ^= Col[2];
+	State[0][2] ^= Col[3];
+	State[1][2] = Col[0];
+	State[1][2] ^= Aes_GfMul[Col[1]][0];
+	State[1][2] ^= Aes_GfMul[Col[2]][1];
+	State[1][2] ^= Col[3];
+	State[2][2] = Col[0];
+	State[2][2] ^= Col[1];
+	State[2][2] ^= Aes_GfMul[Col[2]][0];
+	State[2][2] ^= Aes_GfMul[Col[3]][1];
+	State[3][2] = Aes_GfMul[Col[0]][1];
+	State[3][2] ^= Col[1];
+	State[3][2] ^= Col[2];
+	State[3][2] ^= Aes_GfMul[Col[3]][0];
+	// Column 4
+	Col[0] = State[0][3];
+	Col[1] = State[1][3];
+	Col[2] = State[2][3];
+	Col[3] = State[3][3];
+	State[0][3] = Aes_GfMul[Col[0]][0];
+	State[0][3] ^= Aes_GfMul[Col[1]][1];
+	State[0][3] ^= Col[2];
+	State[0][3] ^= Col[3];
+	State[1][3] = Col[0];
+	State[1][3] ^= Aes_GfMul[Col[1]][0];
+	State[1][3] ^= Aes_GfMul[Col[2]][1];
+	State[1][3] ^= Col[3];
+	State[2][3] = Col[0];
+	State[2][3] ^= Col[1];
+	State[2][3] ^= Aes_GfMul[Col[2]][0];
+	State[2][3] ^= Aes_GfMul[Col[3]][1];
+	State[3][3] = Aes_GfMul[Col[0]][1];
+	State[3][3] ^= Col[1];
+	State[3][3] ^= Col[2];
+	State[3][3] ^= Aes_GfMul[Col[3]][0];
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Performs the the inverted MixColums step.
+*
+* @param	State are the statevalues of the AES conversion.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesInvMixColumns(u8 State[][4])
+{
+	u8 Col[4];
+
+	// Column 1
+	Col[0] = State[0][0];
+	Col[1] = State[1][0];
+	Col[2] = State[2][0];
+	Col[3] = State[3][0];
+	State[0][0] = Aes_GfMul[Col[0]][5];
+	State[0][0] ^= Aes_GfMul[Col[1]][3];
+	State[0][0] ^= Aes_GfMul[Col[2]][4];
+	State[0][0] ^= Aes_GfMul[Col[3]][2];
+	State[1][0] = Aes_GfMul[Col[0]][2];
+	State[1][0] ^= Aes_GfMul[Col[1]][5];
+	State[1][0] ^= Aes_GfMul[Col[2]][3];
+	State[1][0] ^= Aes_GfMul[Col[3]][4];
+	State[2][0] = Aes_GfMul[Col[0]][4];
+	State[2][0] ^= Aes_GfMul[Col[1]][2];
+	State[2][0] ^= Aes_GfMul[Col[2]][5];
+	State[2][0] ^= Aes_GfMul[Col[3]][3];
+	State[3][0] = Aes_GfMul[Col[0]][3];
+	State[3][0] ^= Aes_GfMul[Col[1]][4];
+	State[3][0] ^= Aes_GfMul[Col[2]][2];
+	State[3][0] ^= Aes_GfMul[Col[3]][5];
+	// Column 2
+	Col[0] = State[0][1];
+	Col[1] = State[1][1];
+	Col[2] = State[2][1];
+	Col[3] = State[3][1];
+	State[0][1] = Aes_GfMul[Col[0]][5];
+	State[0][1] ^= Aes_GfMul[Col[1]][3];
+	State[0][1] ^= Aes_GfMul[Col[2]][4];
+	State[0][1] ^= Aes_GfMul[Col[3]][2];
+	State[1][1] = Aes_GfMul[Col[0]][2];
+	State[1][1] ^= Aes_GfMul[Col[1]][5];
+	State[1][1] ^= Aes_GfMul[Col[2]][3];
+	State[1][1] ^= Aes_GfMul[Col[3]][4];
+	State[2][1] = Aes_GfMul[Col[0]][4];
+	State[2][1] ^= Aes_GfMul[Col[1]][2];
+	State[2][1] ^= Aes_GfMul[Col[2]][5];
+	State[2][1] ^= Aes_GfMul[Col[3]][3];
+	State[3][1] = Aes_GfMul[Col[0]][3];
+	State[3][1] ^= Aes_GfMul[Col[1]][4];
+	State[3][1] ^= Aes_GfMul[Col[2]][2];
+	State[3][1] ^= Aes_GfMul[Col[3]][5];
+	// Column 3
+	Col[0] = State[0][2];
+	Col[1] = State[1][2];
+	Col[2] = State[2][2];
+	Col[3] = State[3][2];
+	State[0][2] = Aes_GfMul[Col[0]][5];
+	State[0][2] ^= Aes_GfMul[Col[1]][3];
+	State[0][2] ^= Aes_GfMul[Col[2]][4];
+	State[0][2] ^= Aes_GfMul[Col[3]][2];
+	State[1][2] = Aes_GfMul[Col[0]][2];
+	State[1][2] ^= Aes_GfMul[Col[1]][5];
+	State[1][2] ^= Aes_GfMul[Col[2]][3];
+	State[1][2] ^= Aes_GfMul[Col[3]][4];
+	State[2][2] = Aes_GfMul[Col[0]][4];
+	State[2][2] ^= Aes_GfMul[Col[1]][2];
+	State[2][2] ^= Aes_GfMul[Col[2]][5];
+	State[2][2] ^= Aes_GfMul[Col[3]][3];
+	State[3][2] = Aes_GfMul[Col[0]][3];
+	State[3][2] ^= Aes_GfMul[Col[1]][4];
+	State[3][2] ^= Aes_GfMul[Col[2]][2];
+	State[3][2] ^= Aes_GfMul[Col[3]][5];
+	// Column 4
+	Col[0] = State[0][3];
+	Col[1] = State[1][3];
+	Col[2] = State[2][3];
+	Col[3] = State[3][3];
+	State[0][3] = Aes_GfMul[Col[0]][5];
+	State[0][3] ^= Aes_GfMul[Col[1]][3];
+	State[0][3] ^= Aes_GfMul[Col[2]][4];
+	State[0][3] ^= Aes_GfMul[Col[3]][2];
+	State[1][3] = Aes_GfMul[Col[0]][2];
+	State[1][3] ^= Aes_GfMul[Col[1]][5];
+	State[1][3] ^= Aes_GfMul[Col[2]][3];
+	State[1][3] ^= Aes_GfMul[Col[3]][4];
+	State[2][3] = Aes_GfMul[Col[0]][4];
+	State[2][3] ^= Aes_GfMul[Col[1]][2];
+	State[2][3] ^= Aes_GfMul[Col[2]][5];
+	State[2][3] ^= Aes_GfMul[Col[3]][3];
+	State[3][3] = Aes_GfMul[Col[0]][3];
+	State[3][3] ^= Aes_GfMul[Col[1]][4];
+	State[3][3] ^= Aes_GfMul[Col[2]][2];
+	State[3][3] ^= Aes_GfMul[Col[3]][5];
+}
+
+#ifdef AES_CIPHER_CTR_MODE
+/*****************************************************************************/
+/**
+*
+* This function increments IV. It is used for AES-CTR.
+*
+* @param	Iv is the initialization vector used.
+* @param	CounterSize is the size of the counter block.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesIncrementIv(u8 Iv[], int CounterSize)
+{
+	int Idx;
+
+	// Use CounterSize bytes at the end of the IV as the big-endian integer to increment.
+	for (Idx = AES_BLOCK_SIZE - 1; Idx >= AES_BLOCK_SIZE -
+		 CounterSize; Idx--) {
+		Iv[Idx]++;
+		if (Iv[Idx] != 0 || Idx == AES_BLOCK_SIZE - CounterSize)
+			break;
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+*
+* This function encrypts using AES encryption.
+*
+* @param	In is 16 bytes of plaintext
+* @param	Out is 16 bytes of ciphertext
+* @param	Key is from the key setup
+* @param	KeySize is the bit length of the key, 128, 192, or 256
+*
+* @return	None.
+*
+* @note		Key setup must be done before any AES en/de-cryption functions
+* 			can be used.
+*
+******************************************************************************/
+static void AesEncrypt(const u8 In[], u8 Out[], const u32 Key[], int KeySize)
+{
+	u8 State[4][4];
+
+	/* Copy input array (should be 16 bytes long) to a matrix (sequential bytes are ordered
+	   by row, not Col) called "State" for processing.
+	   *** Implementation note: The official AES documentation references the State by
+	   column, then row. Accessing an element in C requires row then column. Thus, all State
+	   references in AES must have the column and row indexes reversed for C implementation. */
+	State[0][0] = In[0];
+	State[1][0] = In[1];
+	State[2][0] = In[2];
+	State[3][0] = In[3];
+	State[0][1] = In[4];
+	State[1][1] = In[5];
+	State[2][1] = In[6];
+	State[3][1] = In[7];
+	State[0][2] = In[8];
+	State[1][2] = In[9];
+	State[2][2] = In[10];
+	State[3][2] = In[11];
+	State[0][3] = In[12];
+	State[1][3] = In[13];
+	State[2][3] = In[14];
+	State[3][3] = In[15];
+
+	// Perform the necessary number of rounds. The round key is added first.
+	// The last round does not perform the MixColumns step.
+	AesAddRoundKey(State,&Key[0]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[4]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[8]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[12]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[16]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[20]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[24]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[28]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[32]);
+	AesSubBytes(State); AesShiftRows(State);
+	AesMixColumns(State); AesAddRoundKey(State,&Key[36]);
+	if (KeySize != 128) {
+		AesSubBytes(State); AesShiftRows(State);
+		AesMixColumns(State); AesAddRoundKey(State,&Key[40]);
+		AesSubBytes(State); AesShiftRows(State);
+		AesMixColumns(State); AesAddRoundKey(State,&Key[44]);
+		if (KeySize != 192) {
+			AesSubBytes(State); AesShiftRows(State);
+			AesMixColumns(State); AesAddRoundKey(State,&Key[48]);
+			AesSubBytes(State); AesShiftRows(State);
+			AesMixColumns(State); AesAddRoundKey(State,&Key[52]);
+			AesSubBytes(State); AesShiftRows(State);
+			AesAddRoundKey(State,&Key[56]);
+		}
+		else {
+			AesSubBytes(State); AesShiftRows(State);
+			AesAddRoundKey(State,&Key[48]);
+		}
+	}
+	else {
+		AesSubBytes(State); AesShiftRows(State);
+		AesAddRoundKey(State,&Key[40]);
+	}
+
+	// Copy the State to the output array.
+	Out[0] = State[0][0];
+	Out[1] = State[1][0];
+	Out[2] = State[2][0];
+	Out[3] = State[3][0];
+	Out[4] = State[0][1];
+	Out[5] = State[1][1];
+	Out[6] = State[2][1];
+	Out[7] = State[3][1];
+	Out[8] = State[0][2];
+	Out[9] = State[1][2];
+	Out[10] = State[2][2];
+	Out[11] = State[3][2];
+	Out[12] = State[0][3];
+	Out[13] = State[1][3];
+	Out[14] = State[2][3];
+	Out[15] = State[3][3];
+}
+
+/*****************************************************************************/
+/**
+*
+* This function decrypts using AES.
+*
+* @param	In is 16 bytes of ciphertext
+* @param	Out is 16 bytes of plaintext
+* @param	Key is from the key setup
+* @param	KeySize is the bit length of the key, 128, 192, or 256
+*
+* @return	None.
+*
+* @note		Key setup must be done before any AES en/de-cryption functions
+* 			can be used.
+*
+******************************************************************************/
+static void AesDecrypt(const u8 In[], u8 Out[], const u32 Key[], int KeySize)
+{
+	u8 State[4][4];
+
+	// Copy the input to the State.
+	State[0][0] = In[0];
+	State[1][0] = In[1];
+	State[2][0] = In[2];
+	State[3][0] = In[3];
+	State[0][1] = In[4];
+	State[1][1] = In[5];
+	State[2][1] = In[6];
+	State[3][1] = In[7];
+	State[0][2] = In[8];
+	State[1][2] = In[9];
+	State[2][2] = In[10];
+	State[3][2] = In[11];
+	State[0][3] = In[12];
+	State[1][3] = In[13];
+	State[2][3] = In[14];
+	State[3][3] = In[15];
+
+	// Perform the necessary number of rounds. The round key is added first.
+	// The last round does not perform the MixColumns step.
+	if (KeySize > 128) {
+		if (KeySize > 192) {
+			AesAddRoundKey(State,&Key[56]);
+			AesInvShiftRows(State);AesInvSubBytes(State);
+			AesAddRoundKey(State,&Key[52]);AesInvMixColumns(State);
+			AesInvShiftRows(State);AesInvSubBytes(State);
+			AesAddRoundKey(State,&Key[48]);AesInvMixColumns(State);
+		}
+		else {
+			AesAddRoundKey(State,&Key[48]);
+		}
+		AesInvShiftRows(State);AesInvSubBytes(State);
+		AesAddRoundKey(State,&Key[44]);AesInvMixColumns(State);
+		AesInvShiftRows(State);AesInvSubBytes(State);
+		AesAddRoundKey(State,&Key[40]);AesInvMixColumns(State);
+	}
+	else {
+		AesAddRoundKey(State,&Key[40]);
+	}
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[36]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[32]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[28]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[24]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[20]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[16]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[12]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[8]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[4]);AesInvMixColumns(State);
+	AesInvShiftRows(State);AesInvSubBytes(State);
+	AesAddRoundKey(State,&Key[0]);
+
+	// Copy the State to the output array.
+	Out[0] = State[0][0];
+	Out[1] = State[1][0];
+	Out[2] = State[2][0];
+	Out[3] = State[3][0];
+	Out[4] = State[0][1];
+	Out[5] = State[1][1];
+	Out[6] = State[2][1];
+	Out[7] = State[3][1];
+	Out[8] = State[0][2];
+	Out[9] = State[1][2];
+	Out[10] = State[2][2];
+	Out[11] = State[3][2];
+	Out[12] = State[0][3];
+	Out[13] = State[1][3];
+	Out[14] = State[2][3];
+	Out[15] = State[3][3];
+}
+
+
+#ifdef AES_CIPHER_CTR_MODE
+/*****************************************************************************/
+/**
+*
+* This function encrypts using AES and a counter.
+*
+* @param	In is the plaintext
+* @param	InLen is any bytes length
+* @param	Out is is the ciphertext, same length as plaintext
+* @param	Key is from the key setup
+* @param	KeySize is the bit length of the key
+* @param	Iv must be AES_BLOCK_SIZE bytes long
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesEncryptCtr(const u8 In[], size_t InLen, u8 Out[],
+								  const u32 Key[], int KeySize, const u8 Iv[])
+{
+	size_t Idx = 0, LastBlockLength;
+	u8 iv_buf[AES_BLOCK_SIZE], out_buf[AES_BLOCK_SIZE];
+
+	if (In != Out)
+		memcpy(Out, In, InLen);
+
+	memcpy(iv_buf, Iv, AES_BLOCK_SIZE);
+	LastBlockLength = InLen - AES_BLOCK_SIZE;
+
+	if (InLen > AES_BLOCK_SIZE) {
+		for (Idx = 0; Idx < LastBlockLength; Idx += AES_BLOCK_SIZE) {
+			AesEncrypt(iv_buf, out_buf, Key, KeySize);
+			Xor(&Out[Idx], out_buf, &Out[Idx], AES_BLOCK_SIZE);
+			AesIncrementIv(iv_buf, AES_BLOCK_SIZE);
+		}
+	}
+
+	AesEncrypt(iv_buf, out_buf, Key, KeySize);
+	/* Use the Most Significant bytes. */
+	Xor(&Out[Idx], out_buf, &Out[Idx], InLen - Idx);
+}
+#endif
+
+#ifdef AES_CIPHER_CTR_MODE
+/*****************************************************************************/
+/**
+*
+* This function does a AES-CTR decryption (is the same as encryption)
+*
+* @param	In is the ciphertext
+* @param	InLen is any byte length
+* @param	Out is the ciphertext, same length as plaintext
+* @param	Key is from the key setup
+* @param	KeySize is the bit length of the key, 128, 192, or 256
+* @param	Iv must be AES_BLOCK_SIZE bytes long
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void AesDecryptCtr(const u8 In[], size_t InLen, u8 Out[],
+								 const u32 Key[], int KeySize, const u8 Iv[])
+{
+	// CTR encryption is its own inverse function.
+	AesEncryptCtr(In, InLen, Out, Key, KeySize, Iv);
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/aes256.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/aes256.c
@@ -0,0 +1,372 @@
+/******************************************************************************
+*
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*  
+*   Byte-oriented AES-256 implementation.
+*   All lookup tables replaced with 'on the fly' calculations.
+*
+*   Copyright (c) 2007-2009 Ilya O. Levin, http://www.literatecode.com
+*   Other contributors: Hal Finney
+*
+*   Permission to use, copy, modify, and distribute this software for any
+*   purpose with or without fee is hereby granted, provided that the above
+*   copyright notice and this permission notice appear in all copies.
+*
+*   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+*   WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+*   MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+*   ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+*   WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+*   ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+*   OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+*/
+#include "aes256.h"
+
+#define F(x)   (((x)<<1) ^ ((((x)>>7) & 1) * 0x1b))
+#define FD(x)  (((x) >> 1) ^ (((x) & 1) ? 0x8d : 0))
+
+#define BACK_TO_TABLES
+#ifdef BACK_TO_TABLES
+
+const uint8_t sbox[256] = {
+    0x63, 0x7c, 0x77, 0x7b, 0xf2, 0x6b, 0x6f, 0xc5,
+    0x30, 0x01, 0x67, 0x2b, 0xfe, 0xd7, 0xab, 0x76,
+    0xca, 0x82, 0xc9, 0x7d, 0xfa, 0x59, 0x47, 0xf0,
+    0xad, 0xd4, 0xa2, 0xaf, 0x9c, 0xa4, 0x72, 0xc0,
+    0xb7, 0xfd, 0x93, 0x26, 0x36, 0x3f, 0xf7, 0xcc,
+    0x34, 0xa5, 0xe5, 0xf1, 0x71, 0xd8, 0x31, 0x15,
+    0x04, 0xc7, 0x23, 0xc3, 0x18, 0x96, 0x05, 0x9a,
+    0x07, 0x12, 0x80, 0xe2, 0xeb, 0x27, 0xb2, 0x75,
+    0x09, 0x83, 0x2c, 0x1a, 0x1b, 0x6e, 0x5a, 0xa0,
+    0x52, 0x3b, 0xd6, 0xb3, 0x29, 0xe3, 0x2f, 0x84,
+    0x53, 0xd1, 0x00, 0xed, 0x20, 0xfc, 0xb1, 0x5b,
+    0x6a, 0xcb, 0xbe, 0x39, 0x4a, 0x4c, 0x58, 0xcf,
+    0xd0, 0xef, 0xaa, 0xfb, 0x43, 0x4d, 0x33, 0x85,
+    0x45, 0xf9, 0x02, 0x7f, 0x50, 0x3c, 0x9f, 0xa8,
+    0x51, 0xa3, 0x40, 0x8f, 0x92, 0x9d, 0x38, 0xf5,
+    0xbc, 0xb6, 0xda, 0x21, 0x10, 0xff, 0xf3, 0xd2,
+    0xcd, 0x0c, 0x13, 0xec, 0x5f, 0x97, 0x44, 0x17,
+    0xc4, 0xa7, 0x7e, 0x3d, 0x64, 0x5d, 0x19, 0x73,
+    0x60, 0x81, 0x4f, 0xdc, 0x22, 0x2a, 0x90, 0x88,
+    0x46, 0xee, 0xb8, 0x14, 0xde, 0x5e, 0x0b, 0xdb,
+    0xe0, 0x32, 0x3a, 0x0a, 0x49, 0x06, 0x24, 0x5c,
+    0xc2, 0xd3, 0xac, 0x62, 0x91, 0x95, 0xe4, 0x79,
+    0xe7, 0xc8, 0x37, 0x6d, 0x8d, 0xd5, 0x4e, 0xa9,
+    0x6c, 0x56, 0xf4, 0xea, 0x65, 0x7a, 0xae, 0x08,
+    0xba, 0x78, 0x25, 0x2e, 0x1c, 0xa6, 0xb4, 0xc6,
+    0xe8, 0xdd, 0x74, 0x1f, 0x4b, 0xbd, 0x8b, 0x8a,
+    0x70, 0x3e, 0xb5, 0x66, 0x48, 0x03, 0xf6, 0x0e,
+    0x61, 0x35, 0x57, 0xb9, 0x86, 0xc1, 0x1d, 0x9e,
+    0xe1, 0xf8, 0x98, 0x11, 0x69, 0xd9, 0x8e, 0x94,
+    0x9b, 0x1e, 0x87, 0xe9, 0xce, 0x55, 0x28, 0xdf,
+    0x8c, 0xa1, 0x89, 0x0d, 0xbf, 0xe6, 0x42, 0x68,
+    0x41, 0x99, 0x2d, 0x0f, 0xb0, 0x54, 0xbb, 0x16
+};
+const uint8_t sboxinv[256] = {
+    0x52, 0x09, 0x6a, 0xd5, 0x30, 0x36, 0xa5, 0x38,
+    0xbf, 0x40, 0xa3, 0x9e, 0x81, 0xf3, 0xd7, 0xfb,
+    0x7c, 0xe3, 0x39, 0x82, 0x9b, 0x2f, 0xff, 0x87,
+    0x34, 0x8e, 0x43, 0x44, 0xc4, 0xde, 0xe9, 0xcb,
+    0x54, 0x7b, 0x94, 0x32, 0xa6, 0xc2, 0x23, 0x3d,
+    0xee, 0x4c, 0x95, 0x0b, 0x42, 0xfa, 0xc3, 0x4e,
+    0x08, 0x2e, 0xa1, 0x66, 0x28, 0xd9, 0x24, 0xb2,
+    0x76, 0x5b, 0xa2, 0x49, 0x6d, 0x8b, 0xd1, 0x25,
+    0x72, 0xf8, 0xf6, 0x64, 0x86, 0x68, 0x98, 0x16,
+    0xd4, 0xa4, 0x5c, 0xcc, 0x5d, 0x65, 0xb6, 0x92,
+    0x6c, 0x70, 0x48, 0x50, 0xfd, 0xed, 0xb9, 0xda,
+    0x5e, 0x15, 0x46, 0x57, 0xa7, 0x8d, 0x9d, 0x84,
+    0x90, 0xd8, 0xab, 0x00, 0x8c, 0xbc, 0xd3, 0x0a,
+    0xf7, 0xe4, 0x58, 0x05, 0xb8, 0xb3, 0x45, 0x06,
+    0xd0, 0x2c, 0x1e, 0x8f, 0xca, 0x3f, 0x0f, 0x02,
+    0xc1, 0xaf, 0xbd, 0x03, 0x01, 0x13, 0x8a, 0x6b,
+    0x3a, 0x91, 0x11, 0x41, 0x4f, 0x67, 0xdc, 0xea,
+    0x97, 0xf2, 0xcf, 0xce, 0xf0, 0xb4, 0xe6, 0x73,
+    0x96, 0xac, 0x74, 0x22, 0xe7, 0xad, 0x35, 0x85,
+    0xe2, 0xf9, 0x37, 0xe8, 0x1c, 0x75, 0xdf, 0x6e,
+    0x47, 0xf1, 0x1a, 0x71, 0x1d, 0x29, 0xc5, 0x89,
+    0x6f, 0xb7, 0x62, 0x0e, 0xaa, 0x18, 0xbe, 0x1b,
+    0xfc, 0x56, 0x3e, 0x4b, 0xc6, 0xd2, 0x79, 0x20,
+    0x9a, 0xdb, 0xc0, 0xfe, 0x78, 0xcd, 0x5a, 0xf4,
+    0x1f, 0xdd, 0xa8, 0x33, 0x88, 0x07, 0xc7, 0x31,
+    0xb1, 0x12, 0x10, 0x59, 0x27, 0x80, 0xec, 0x5f,
+    0x60, 0x51, 0x7f, 0xa9, 0x19, 0xb5, 0x4a, 0x0d,
+    0x2d, 0xe5, 0x7a, 0x9f, 0x93, 0xc9, 0x9c, 0xef,
+    0xa0, 0xe0, 0x3b, 0x4d, 0xae, 0x2a, 0xf5, 0xb0,
+    0xc8, 0xeb, 0xbb, 0x3c, 0x83, 0x53, 0x99, 0x61,
+    0x17, 0x2b, 0x04, 0x7e, 0xba, 0x77, 0xd6, 0x26,
+    0xe1, 0x69, 0x14, 0x63, 0x55, 0x21, 0x0c, 0x7d
+};
+
+#define rj_sbox(x)     sbox[(x)]
+#define rj_sbox_inv(x) sboxinv[(x)]
+
+#else /* tableless subroutines */
+
+/* -------------------------------------------------------------------------- */
+uint8_t gf_alog(uint8_t x) // calculate anti-logarithm gen 3
+{
+    uint8_t atb = 1, z;
+
+    while (x--) {z = atb; atb <<= 1; if (z & 0x80) atb^= 0x1b; atb ^= z;}
+
+    return atb;
+} /* gf_alog */
+
+/* -------------------------------------------------------------------------- */
+uint8_t gf_log(uint8_t x) // calculate logarithm gen 3
+{
+    uint8_t atb = 1, i = 0, z;
+
+    do {
+        if (atb == x) break;
+        z = atb; atb <<= 1; if (z & 0x80) atb^= 0x1b; atb ^= z;
+    } while (++i > 0);
+
+    return i;
+} /* gf_log */
+
+
+/* -------------------------------------------------------------------------- */
+uint8_t gf_mulinv(uint8_t x) // calculate multiplicative inverse
+{
+    return (x) ? gf_alog(255 - gf_log(x)) : 0;
+} /* gf_mulinv */
+
+/* -------------------------------------------------------------------------- */
+uint8_t rj_sbox(uint8_t x)
+{
+    uint8_t y, sb;
+
+    sb = y = gf_mulinv(x);
+    y = (y<<1)|(y>>7); sb ^= y;  y = (y<<1)|(y>>7); sb ^= y;
+    y = (y<<1)|(y>>7); sb ^= y;  y = (y<<1)|(y>>7); sb ^= y;
+
+    return (sb ^ 0x63);
+} /* rj_sbox */
+
+/* -------------------------------------------------------------------------- */
+uint8_t rj_sbox_inv(uint8_t x)
+{
+    uint8_t y, sb;
+
+    y = x ^ 0x63;
+    sb = y = (y<<1)|(y>>7);
+    y = (y<<2)|(y>>6); sb ^= y; y = (y<<3)|(y>>5); sb ^= y;
+
+    return gf_mulinv(sb);
+} /* rj_sbox_inv */
+
+#endif
+
+/* -------------------------------------------------------------------------- */
+uint8_t rj_xtime(uint8_t x)
+{
+    return (x & 0x80) ? ((x << 1) ^ 0x1b) : (x << 1);
+} /* rj_xtime */
+
+/* -------------------------------------------------------------------------- */
+void aes_subBytes(uint8_t *buf)
+{
+    register uint8_t i = 16;
+
+    while (i--) buf[i] = rj_sbox(buf[i]);
+} /* aes_subBytes */
+
+/* -------------------------------------------------------------------------- */
+void aes_subBytes_inv(uint8_t *buf)
+{
+    register uint8_t i = 16;
+
+    while (i--) buf[i] = rj_sbox_inv(buf[i]);
+} /* aes_subBytes_inv */
+
+/* -------------------------------------------------------------------------- */
+void aes_addRoundKey(uint8_t *buf, uint8_t *key)
+{
+    register uint8_t i = 16;
+
+    while (i--) buf[i] ^= key[i];
+} /* aes_addRoundKey */
+
+/* -------------------------------------------------------------------------- */
+void aes_addRoundKey_cpy(uint8_t *buf, uint8_t *key, uint8_t *cpk)
+{
+    register uint8_t i = 16;
+
+    while (i--)  buf[i] ^= (cpk[i] = key[i]), cpk[16+i] = key[16 + i];
+} /* aes_addRoundKey_cpy */
+
+
+/* -------------------------------------------------------------------------- */
+void aes_shiftRows(uint8_t *buf)
+{
+    register uint8_t i, j; /* to make it potentially parallelable :) */
+
+    i = buf[1]; buf[1] = buf[5]; buf[5] = buf[9]; buf[9] = buf[13]; buf[13] = i;
+    i = buf[10]; buf[10] = buf[2]; buf[2] = i;
+    j = buf[3]; buf[3] = buf[15]; buf[15] = buf[11]; buf[11] = buf[7]; buf[7] = j;
+    j = buf[14]; buf[14] = buf[6]; buf[6]  = j;
+
+} /* aes_shiftRows */
+
+/* -------------------------------------------------------------------------- */
+void aes_shiftRows_inv(uint8_t *buf)
+{
+    register uint8_t i, j; /* same as above :) */
+
+    i = buf[1]; buf[1] = buf[13]; buf[13] = buf[9]; buf[9] = buf[5]; buf[5] = i;
+    i = buf[2]; buf[2] = buf[10]; buf[10] = i;
+    j = buf[3]; buf[3] = buf[7]; buf[7] = buf[11]; buf[11] = buf[15]; buf[15] = j;
+    j = buf[6]; buf[6] = buf[14]; buf[14] = j;
+
+} /* aes_shiftRows_inv */
+
+/* -------------------------------------------------------------------------- */
+void aes_mixColumns(uint8_t *buf)
+{
+    register uint8_t i, a, b, c, d, e;
+
+    for (i = 0; i < 16; i += 4)
+    {
+        a = buf[i]; b = buf[i + 1]; c = buf[i + 2]; d = buf[i + 3];
+        e = a ^ b ^ c ^ d;
+        buf[i] ^= e ^ rj_xtime(a^b);   buf[i+1] ^= e ^ rj_xtime(b^c);
+        buf[i+2] ^= e ^ rj_xtime(c^d); buf[i+3] ^= e ^ rj_xtime(d^a);
+    }
+} /* aes_mixColumns */
+
+/* -------------------------------------------------------------------------- */
+void aes_mixColumns_inv(uint8_t *buf)
+{
+    register uint8_t i, a, b, c, d, e, x, y, z;
+
+    for (i = 0; i < 16; i += 4)
+    {
+        a = buf[i]; b = buf[i + 1]; c = buf[i + 2]; d = buf[i + 3];
+        e = a ^ b ^ c ^ d;
+        z = rj_xtime(e);
+        x = e ^ rj_xtime(rj_xtime(z^a^c));  y = e ^ rj_xtime(rj_xtime(z^b^d));
+        buf[i] ^= x ^ rj_xtime(a^b);   buf[i+1] ^= y ^ rj_xtime(b^c);
+        buf[i+2] ^= x ^ rj_xtime(c^d); buf[i+3] ^= y ^ rj_xtime(d^a);
+    }
+} /* aes_mixColumns_inv */
+
+/* -------------------------------------------------------------------------- */
+void aes_expandEncKey(uint8_t *k, uint8_t *rc)
+{
+    register uint8_t i;
+
+    k[0] ^= rj_sbox(k[29]) ^ (*rc);
+    k[1] ^= rj_sbox(k[30]);
+    k[2] ^= rj_sbox(k[31]);
+    k[3] ^= rj_sbox(k[28]);
+    *rc = F( *rc);
+
+    for(i = 4; i < 16; i += 4)  k[i] ^= k[i-4],   k[i+1] ^= k[i-3],
+        k[i+2] ^= k[i-2], k[i+3] ^= k[i-1];
+    k[16] ^= rj_sbox(k[12]);
+    k[17] ^= rj_sbox(k[13]);
+    k[18] ^= rj_sbox(k[14]);
+    k[19] ^= rj_sbox(k[15]);
+
+    for(i = 20; i < 32; i += 4) k[i] ^= k[i-4],   k[i+1] ^= k[i-3],
+        k[i+2] ^= k[i-2], k[i+3] ^= k[i-1];
+
+} /* aes_expandEncKey */
+
+/* -------------------------------------------------------------------------- */
+void aes_expandDecKey(uint8_t *k, uint8_t *rc)
+{
+    uint8_t i;
+
+    for(i = 28; i > 16; i -= 4) k[i+0] ^= k[i-4], k[i+1] ^= k[i-3],
+        k[i+2] ^= k[i-2], k[i+3] ^= k[i-1];
+
+    k[16] ^= rj_sbox(k[12]);
+    k[17] ^= rj_sbox(k[13]);
+    k[18] ^= rj_sbox(k[14]);
+    k[19] ^= rj_sbox(k[15]);
+
+    for(i = 12; i > 0; i -= 4)  k[i+0] ^= k[i-4], k[i+1] ^= k[i-3],
+        k[i+2] ^= k[i-2], k[i+3] ^= k[i-1];
+
+    *rc = FD(*rc);
+    k[0] ^= rj_sbox(k[29]) ^ (*rc);
+    k[1] ^= rj_sbox(k[30]);
+    k[2] ^= rj_sbox(k[31]);
+    k[3] ^= rj_sbox(k[28]);
+} /* aes_expandDecKey */
+
+
+/* -------------------------------------------------------------------------- */
+void aes256_init(aes256_context *ctx, uint8_t *k)
+{
+    uint8_t rcon = 1;
+    register uint8_t i;
+
+    for (i = 0; i < sizeof(ctx->key); i++) ctx->enckey[i] = ctx->deckey[i] = k[i];
+    for (i = 8;--i;) aes_expandEncKey(ctx->deckey, &rcon);
+} /* aes256_init */
+
+/* -------------------------------------------------------------------------- */
+void aes256_done(aes256_context *ctx)
+{
+    register uint8_t i;
+
+    for (i = 0; i < sizeof(ctx->key); i++)
+        ctx->key[i] = ctx->enckey[i] = ctx->deckey[i] = 0;
+} /* aes256_done */
+
+/* -------------------------------------------------------------------------- */
+void aes256_encrypt_ecb(aes256_context *ctx, uint8_t *buf)
+{
+    uint8_t i, rcon;
+
+    aes_addRoundKey_cpy(buf, ctx->enckey, ctx->key);
+    for(i = 1, rcon = 1; i < 14; ++i)
+    {
+        aes_subBytes(buf);
+        aes_shiftRows(buf);
+        aes_mixColumns(buf);
+        if( i & 1 ) aes_addRoundKey( buf, &ctx->key[16]);
+        else aes_expandEncKey(ctx->key, &rcon), aes_addRoundKey(buf, ctx->key);
+    }
+    aes_subBytes(buf);
+    aes_shiftRows(buf);
+    aes_expandEncKey(ctx->key, &rcon);
+    aes_addRoundKey(buf, ctx->key);
+} /* aes256_encrypt */
+
+/* -------------------------------------------------------------------------- */
+void aes256_decrypt_ecb(aes256_context *ctx, uint8_t *buf)
+{
+    uint8_t i, rcon;
+
+    aes_addRoundKey_cpy(buf, ctx->deckey, ctx->key);
+    aes_shiftRows_inv(buf);
+    aes_subBytes_inv(buf);
+
+    for (i = 14, rcon = 0x80; --i;)
+    {
+        if( ( i & 1 ) )
+        {
+            aes_expandDecKey(ctx->key, &rcon);
+            aes_addRoundKey(buf, &ctx->key[16]);
+        }
+        else aes_addRoundKey(buf, ctx->key);
+        aes_mixColumns_inv(buf);
+        aes_shiftRows_inv(buf);
+        aes_subBytes_inv(buf);
+    }
+    aes_addRoundKey( buf, ctx->key);
+} /* aes256_decrypt */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/aes256.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/aes256.h
@@ -0,0 +1,55 @@
+/******************************************************************************
+*
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*  
+*   Byte-oriented AES-256 implementation.
+*   All lookup tables replaced with 'on the fly' calculations.
+*
+*   Copyright (c) 2007-2009 Ilya O. Levin, http://www.literatecode.com
+*   Other contributors: Hal Finney
+*
+*   Permission to use, copy, modify, and distribute this software for any
+*   purpose with or without fee is hereby granted, provided that the above
+*   copyright notice and this permission notice appear in all copies.
+*
+*   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+*   WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+*   MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+*   ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+*   WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+*   ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+*   OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+*/
+#ifndef uint8_t
+#define uint8_t  unsigned char
+#endif
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+    typedef struct {
+        uint8_t key[32];
+        uint8_t enckey[32];
+        uint8_t deckey[32];
+    } aes256_context;
+
+
+    void aes256_init(aes256_context *, uint8_t * /* key */);
+    void aes256_done(aes256_context *);
+    void aes256_encrypt_ecb(aes256_context *, uint8_t * /* plaintext */);
+    void aes256_decrypt_ecb(aes256_context *, uint8_t * /* cipertext */);
+
+#ifdef __cplusplus
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/bigdigits.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/bigdigits.c
@@ -0,0 +1,1075 @@
+/* $Id: bigdigits.c $ */
+
+/***** BEGIN LICENSE BLOCK *****
+ *
+ * This Source Code Form is subject to the terms of the Mozilla Public
+ * License, v. 2.0. If a copy of the MPL was not distributed with this
+ * file, You can obtain one at http://mozilla.org/MPL/2.0/.
+ *
+ * Copyright (c) 2001-15 David Ireland, D.I. Management Services Pty Limited
+ * <http://www.di-mgt.com.au/bigdigits.html>. All rights reserved.
+ *
+ * Alternatively, the contents of this file may be used under the terms
+ * of the GNU General Public License Version 2, as described below:
+ * 
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+ ***** END LICENSE BLOCK *****/
+/*
+ * Last updated:
+ * $Date: 2015-10-22 10:23:00 $
+ * $Revision: 2.5.0 $
+ * $Author: dai $
+ */
+
+#include "bigdigits.h"
+#include <linux/types.h>
+#include <linux/math64.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <asm-generic/bug.h>
+
+#define assert(a) BUG_ON(!(a))
+
+/* Useful definitions */
+#ifndef max
+#define max(a,b)            (((a) > (b)) ? (a) : (b))
+#endif
+
+/* Added in [v2.4] for ALLOC_BYTES and FREE_BYTES */
+volatile uint8_t zeroise_bytes(volatile void *v, size_t n)
+{	/* Zeroise byte array b and make sure optimiser does not ignore this */
+	volatile uint8_t optdummy;
+	volatile uint8_t *b = (uint8_t*)v;
+	while(n--)
+		b[n] = 0;
+	optdummy = *b;
+	return optdummy;
+}
+
+/* Force linker to include copyright notice in executable object image */
+volatile char *copyright_notice(void)
+{
+	return
+"Contains multiple-precision arithmetic code originally written by David Ireland,"
+" copyright (c) 2001-15 by D.I. Management Services Pty Limited <www.di-mgt.com.au>.";
+}
+
+#define IS_NONZERO_DIGIT(x) (((x)|(~(x)+1)) >> (BITS_PER_DIGIT-1))
+#define IS_ZER0_DIGIT(x) (1 ^ IS_NONZERO_DIGIT((x)))
+
+/** Returns 1 if a == b, else 0 (constant-time) */
+int mpEqual(const u32 a[], const u32 b[], size_t ndigits)
+{
+	u32 dif = 0;
+
+	while (ndigits--) {
+		dif |= a[ndigits] ^ b[ndigits];
+	}
+
+	return (IS_ZER0_DIGIT(dif));
+}
+
+/** Returns 1 if a == 0, else 0 (constant-time) */
+int mpIsZero(const u32 a[], size_t ndigits)
+{
+	u32 dif = 0;
+	const u32 ZERO = 0;
+
+	while (ndigits--) {
+		dif |= a[ndigits] ^ ZERO;
+	}
+
+	return (IS_ZER0_DIGIT(dif));
+}
+
+int spMultiply(u32 p[2], u32 x, u32 y)
+{
+	/* Use a 64-bit temp for product */
+	uint64_t t = (uint64_t)x * (uint64_t)y;
+	/* then split into two parts */
+	p[1] = (u32)(t >> 32);
+	p[0] = (u32)(t & 0xFFFFFFFF);
+
+	return 0;
+}
+
+u32 spDivide(u32 *pq, u32 *pr, const u32 u[2], u32 v)
+{
+	uint64_t uu, q;
+	uu = (uint64_t)u[1] << 32 | (uint64_t)u[0];
+	q = div64_ul(uu, (uint64_t)v);
+	//r = uu % (uint64_t)v;
+	*pr = (u32)(uu - q * v);
+	*pq = (u32)(q & 0xFFFFFFFF);
+	return (u32)(q >> 32);
+}
+
+u32 mpAdd(u32 w[], const u32 u[], const u32 v[], size_t ndigits)
+{
+	/*	Calculates w = u + v
+		where w, u, v are multiprecision integers of ndigits each
+		Returns carry if overflow. Carry = 0 or 1.
+
+		Ref: Knuth Vol 2 Ch 4.3.1 p 266 Algorithm A.
+	*/
+
+	u32 k;
+	size_t j;
+
+	assert(w != v);
+
+	/* Step A1. Initialise */
+	k = 0;
+
+	for (j = 0; j < ndigits; j++)
+	{
+		/*	Step A2. Add digits w_j = (u_j + v_j + k)
+			Set k = 1 if carry (overflow) occurs
+		*/
+		w[j] = u[j] + k;
+		if (w[j] < k)
+			k = 1;
+		else
+			k = 0;
+
+		w[j] += v[j];
+		if (w[j] < v[j])
+			k++;
+
+	}	/* Step A3. Loop on j */
+
+	return k;	/* w_n = k */
+}
+
+u32 mpSubtract(u32 w[], const u32 u[], const u32 v[], size_t ndigits)
+{
+	/*	Calculates w = u - v where u >= v
+		w, u, v are multiprecision integers of ndigits each
+		Returns 0 if OK, or 1 if v > u.
+
+		Ref: Knuth Vol 2 Ch 4.3.1 p 267 Algorithm S.
+	*/
+
+	u32 k;
+	size_t j;
+
+	assert(w != v);
+
+	/* Step S1. Initialise */
+	k = 0;
+
+	for (j = 0; j < ndigits; j++)
+	{
+		/*	Step S2. Subtract digits w_j = (u_j - v_j - k)
+			Set k = 1 if borrow occurs.
+		*/
+		w[j] = u[j] - k;
+		if (w[j] > MAX_DIGIT - k)
+			k = 1;
+		else
+			k = 0;
+
+		w[j] -= v[j];
+		if (w[j] > MAX_DIGIT - v[j])
+			k++;
+
+	}	/* Step S3. Loop on j */
+
+	return k;	/* Should be zero if u >= v */
+}
+
+int mpMultiply(u32 w[], const u32 u[], const u32 v[], size_t ndigits)
+{
+	/*	Computes product w = u * v
+		where u, v are multiprecision integers of ndigits each
+		and w is a multiprecision integer of 2*ndigits
+
+		Ref: Knuth Vol 2 Ch 4.3.1 p 268 Algorithm M.
+	*/
+
+	u32 k, t[2];
+	size_t i, j, m, n;
+
+	assert(w != u && w != v);
+
+	m = n = ndigits;
+
+	/* Step M1. Initialise */
+	for (i = 0; i < 2 * m; i++)
+		w[i] = 0;
+
+	for (j = 0; j < n; j++)
+	{
+		/* Step M2. Zero multiplier? */
+		if (v[j] == 0)
+		{
+			w[j + m] = 0;
+		}
+		else
+		{
+			/* Step M3. Initialise i */
+			k = 0;
+			for (i = 0; i < m; i++)
+			{
+				/* Step M4. Multiply and add */
+				/* t = u_i * v_j + w_(i+j) + k */
+				spMultiply(t, u[i], v[j]);
+
+				t[0] += k;
+				if (t[0] < k)
+					t[1]++;
+				t[0] += w[i+j];
+				if (t[0] < w[i+j])
+					t[1]++;
+
+				w[i+j] = t[0];
+				k = t[1];
+			}
+			/* Step M5. Loop on i, set w_(j+m) = k */
+			w[j+m] = k;
+		}
+	}	/* Step M6. Loop on j */
+
+	return 0;
+}
+
+static u32 mpMultSub(u32 wn, u32 w[], const u32 v[],
+					   u32 q, size_t n)
+{	/*	Compute w = w - qv
+		where w = (WnW[n-1]...W[0])
+		return modified Wn.
+	*/
+	u32 k, t[2];
+	size_t i;
+
+	if (q == 0)	/* No change */
+		return wn;
+
+	k = 0;
+
+	for (i = 0; i < n; i++)
+	{
+		spMultiply(t, q, v[i]);
+		w[i] -= k;
+		if (w[i] > MAX_DIGIT - k)
+			k = 1;
+		else
+			k = 0;
+		w[i] -= t[0];
+		if (w[i] > MAX_DIGIT - t[0])
+			k++;
+		k += t[1];
+	}
+
+	/* Cope with Wn not stored in array w[0..n-1] */
+	wn -= k;
+
+	return wn;
+}
+
+static int QhatTooBig(u32 qhat, u32 rhat,
+					  u32 vn2, u32 ujn2)
+{	/*	Returns true if Qhat is too big
+		i.e. if (Qhat * Vn-2) > (b.Rhat + Uj+n-2)
+	*/
+	u32 t[2];
+
+	spMultiply(t, qhat, vn2);
+	if (t[1] < rhat)
+		return 0;
+	else if (t[1] > rhat)
+		return 1;
+	else if (t[0] > ujn2)
+		return 1;
+
+	return 0;
+}
+
+int mpDivide(u32 q[], u32 r[], const u32 u[],
+	size_t udigits, u32 v[], size_t vdigits)
+{	/*	Computes quotient q = u / v and remainder r = u mod v
+		where q, r, u are multiple precision digits
+		all of udigits and the divisor v is vdigits.
+
+		Ref: Knuth Vol 2 Ch 4.3.1 p 272 Algorithm D.
+
+		Do without extra storage space, i.e. use r[] for
+		normalised u[], unnormalise v[] at end, and cope with
+		extra digit Uj+n added to u after normalisation.
+
+		WARNING: this trashes q and r first, so cannot do
+		u = u / v or v = u mod v.
+		It also changes v temporarily so cannot make it const.
+	*/
+	size_t shift;
+	int n, m, j;
+	u32 bitmask, overflow;
+	u32 qhat, rhat, t[2];
+	u32 *uu, *ww;
+	int qhatOK, cmp;
+
+	/* Clear q and r */
+	mpSetZero(q, udigits);
+	mpSetZero(r, udigits);
+
+	/* Work out exact sizes of u and v */
+	n = (int)mpSizeof(v, vdigits);
+	m = (int)mpSizeof(u, udigits);
+	m -= n;
+
+	/* Catch special cases */
+	if (n == 0)
+		return -1;	/* Error: divide by zero */
+
+	if (n == 1)
+	{	/* Use short division instead */
+		r[0] = mpShortDiv(q, u, v[0], udigits);
+		return 0;
+	}
+
+	if (m < 0)
+	{	/* v > u, so just set q = 0 and r = u */
+		mpSetEqual(r, u, udigits);
+		return 0;
+	}
+
+	if (m == 0)
+	{	/* u and v are the same length */
+		cmp = mpCompare(u, v, (size_t)n);
+		if (cmp < 0)
+		{	/* v > u, as above */
+			mpSetEqual(r, u, udigits);
+			return 0;
+		}
+		else if (cmp == 0)
+		{	/* v == u, so set q = 1 and r = 0 */
+			mpSetDigit(q, 1, udigits);
+			return 0;
+		}
+	}
+
+	/*	In Knuth notation, we have:
+		Given
+		u = (Um+n-1 ... U1U0)
+		v = (Vn-1 ... V1V0)
+		Compute
+		q = u/v = (QmQm-1 ... Q0)
+		r = u mod v = (Rn-1 ... R1R0)
+	*/
+
+	/*	Step D1. Normalise */
+	/*	Requires high bit of Vn-1
+		to be set, so find most signif. bit then shift left,
+		i.e. d = 2^shift, u' = u * d, v' = v * d.
+	*/
+	bitmask = HIBITMASK;
+	for (shift = 0; shift < BITS_PER_DIGIT; shift++)
+	{
+		if (v[n-1] & bitmask)
+			break;
+		bitmask >>= 1;
+	}
+
+	/* Normalise v in situ - NB only shift non-zero digits */
+	overflow = mpShiftLeft(v, v, shift, n);
+
+	/* Copy normalised dividend u*d into r */
+	overflow = mpShiftLeft(r, u, shift, n + m);
+	uu = r;	/* Use ptr to keep notation constant */
+
+	t[0] = overflow;	/* Extra digit Um+n */
+
+	/* Step D2. Initialise j. Set j = m */
+	for (j = m; j >= 0; j--)
+	{
+		/* Step D3. Set Qhat = [(b.Uj+n + Uj+n-1)/Vn-1]
+		   and Rhat = remainder */
+		qhatOK = 0;
+		t[1] = t[0];	/* This is Uj+n */
+		t[0] = uu[j+n-1];
+		overflow = spDivide(&qhat, &rhat, t, v[n-1]);
+
+		/* Test Qhat */
+		if (overflow)
+		{	/* Qhat == b so set Qhat = b - 1 */
+			qhat = MAX_DIGIT;
+			rhat = uu[j+n-1];
+			rhat += v[n-1];
+			if (rhat < v[n-1])	/* Rhat >= b, so no re-test */
+				qhatOK = 1;
+		}
+		/* [VERSION 2: Added extra test "qhat && "] */
+		if (qhat && !qhatOK && QhatTooBig(qhat, rhat, v[n-2], uu[j+n-2]))
+		{	/* If Qhat.Vn-2 > b.Rhat + Uj+n-2
+			   decrease Qhat by one, increase Rhat by Vn-1
+			*/
+			qhat--;
+			rhat += v[n-1];
+			/* Repeat this test if Rhat < b */
+			if (!(rhat < v[n-1]))
+				if (QhatTooBig(qhat, rhat, v[n-2], uu[j+n-2]))
+					qhat--;
+		}
+
+
+		/* Step D4. Multiply and subtract */
+		ww = &uu[j];
+		overflow = mpMultSub(t[1], ww, v, qhat, (size_t)n);
+
+		/* Step D5. Test remainder. Set Qj = Qhat */
+		q[j] = qhat;
+		if (overflow)
+		{	/* Step D6. Add back if D4 was negative */
+			q[j]--;
+			overflow = mpAdd(ww, ww, v, (size_t)n);
+		}
+
+		t[0] = uu[j+n-1];	/* Uj+n on next round */
+
+	}	/* Step D7. Loop on j */
+
+	/* Clear high digits in uu */
+	for (j = n; j < m+n; j++)
+		uu[j] = 0;
+
+	/* Step D8. Unnormalise. */
+
+	mpShiftRight(r, r, shift, n);
+	mpShiftRight(v, v, shift, n);
+
+	return 0;
+}
+
+int mpSquare(u32 w[], const u32 x[], size_t ndigits)
+/* New in Version 2.0 */
+{
+	/*	Computes square w = x * x
+		where x is a multiprecision integer of ndigits
+		and w is a multiprecision integer of 2*ndigits
+
+		Ref: Menezes p596 Algorithm 14.16 with errata.
+	*/
+
+	u32 k, p[2], u[2], cbit, carry;
+	size_t i, j, t, i2, cpos;
+
+	assert(w != x);
+
+	t = ndigits;
+
+	/* 1. For i from 0 to (2t-1) do: w_i = 0 */
+	i2 = t << 1;
+	for (i = 0; i < i2; i++)
+		w[i] = 0;
+
+	carry = 0;
+	cpos = i2-1;
+	/* 2. For i from 0 to (t-1) do: */
+	for (i = 0; i < t; i++)
+	{
+		/* 2.1 (uv) = w_2i + x_i * x_i, w_2i = v, c = u
+		   Careful, w_2i may be double-prec
+		*/
+		i2 = i << 1; /* 2*i */
+		spMultiply(p, x[i], x[i]);
+		p[0] += w[i2];
+		if (p[0] < w[i2])
+			p[1]++;
+		k = 0;	/* p[1] < b, so no overflow here */
+		if (i2 == cpos && carry)
+		{
+			p[1] += carry;
+			if (p[1] < carry)
+				k++;
+			carry = 0;
+		}
+		w[i2] = p[0];
+		u[0] = p[1];
+		u[1] = k;
+
+		/* 2.2 for j from (i+1) to (t-1) do:
+		   (uv) = w_{i+j} + 2x_j * x_i + c,
+		   w_{i+j} = v, c = u,
+		   u is double-prec
+		   w_{i+j} is dbl if [i+j] == cpos
+		*/
+		k = 0;
+		for (j = i+1; j < t; j++)
+		{
+			/* p = x_j * x_i */
+			spMultiply(p, x[j], x[i]);
+			/* p = 2p <=> p <<= 1 */
+			cbit = (p[0] & HIBITMASK) != 0;
+			k =  (p[1] & HIBITMASK) != 0;
+			p[0] <<= 1;
+			p[1] <<= 1;
+			p[1] |= cbit;
+			/* p = p + c */
+			p[0] += u[0];
+			if (p[0] < u[0])
+			{
+				p[1]++;
+				if (p[1] == 0)
+					k++;
+			}
+			p[1] += u[1];
+			if (p[1] < u[1])
+				k++;
+			/* p = p + w_{i+j} */
+			p[0] += w[i+j];
+			if (p[0] < w[i+j])
+			{
+				p[1]++;
+				if (p[1] == 0)
+					k++;
+			}
+			if ((i+j) == cpos && carry)
+			{	/* catch overflow from last round */
+				p[1] += carry;
+				if (p[1] < carry)
+					k++;
+				carry = 0;
+			}
+			/* w_{i+j} = v, c = u */
+			w[i+j] = p[0];
+			u[0] = p[1];
+			u[1] = k;
+		}
+		/* 2.3 w_{i+t} = u */
+		w[i+t] = u[0];
+		/* remember overflow in w_{i+t} */
+		carry = u[1];
+		cpos = i+t;
+	}
+
+	/* (NB original step 3 deleted in Menezes errata) */
+
+	/* Return w */
+
+	return 0;
+}
+
+/** Returns sign of (a - b) as 0, +1 or -1 (constant-time) */
+int mpCompare(const u32 a[], const u32 b[], size_t ndigits)
+{
+	/* All these vars are either 0 or 1 */
+	unsigned int gt = 0;
+	unsigned int lt = 0;
+	unsigned int mask = 1;	/* Set to zero once first inequality found */
+	unsigned int c;
+
+	while (ndigits--) {
+		gt |= (a[ndigits] > b[ndigits]) & mask;
+		lt |= (a[ndigits] < b[ndigits]) & mask;
+		c = (gt | lt);
+		mask &= (c-1);	/* Unchanged if c==0 or mask==0, else mask=0 */
+	}
+
+	return (int)gt - (int)lt;	/* EQ=0 GT=+1 LT=-1 */
+}
+
+/** Returns number of significant digits in a */
+size_t mpSizeof(const u32 a[], size_t ndigits)
+{
+	while(ndigits--)
+	{
+		if (a[ndigits] != 0)
+			return (++ndigits);
+	}
+	return 0;
+}
+
+size_t mpBitLength(const u32 d[], size_t ndigits)
+/* Returns no of significant bits in d */
+{
+	size_t n, i, bits;
+	u32 mask;
+
+	if (!d || ndigits == 0)
+		return 0;
+
+	n = mpSizeof(d, ndigits);
+	if (0 == n) return 0;
+
+	for (i = 0, mask = HIBITMASK; mask > 0; mask >>= 1, i++)
+	{
+		if (d[n-1] & mask)
+			break;
+	}
+
+	bits = n * BITS_PER_DIGIT - i;
+
+	return bits;
+}
+
+void mpSetEqual(u32 a[], const u32 b[], size_t ndigits)
+{	/* Sets a = b */
+	size_t i;
+
+	for (i = 0; i < ndigits; i++)
+	{
+		a[i] = b[i];
+	}
+}
+
+volatile u32 mpSetZero(volatile u32 a[], size_t ndigits)
+{	/* Sets a = 0 */
+
+	/* Prevent optimiser ignoring this */
+	volatile u32 optdummy;
+	volatile u32 *p = a;
+
+	while (ndigits--)
+		a[ndigits] = 0;
+
+	optdummy = *p;
+	return optdummy;
+}
+
+int mpGetBit(u32 a[], size_t ndigits, size_t ibit)
+	/* Returns value 1 or 0 of bit n (0..nbits-1); or -1 if out of range */
+{
+	size_t idigit, bit_to_get;
+	u32 mask;
+
+	/* Which digit? (0-based) */
+	idigit = ibit / BITS_PER_DIGIT;
+	if (idigit >= ndigits)
+		return -1;
+
+	/* Set mask */
+	bit_to_get = ibit % BITS_PER_DIGIT;
+	mask = 0x01 << bit_to_get;
+
+	return ((a[idigit] & mask) ? 1 : 0);
+}
+
+void mpSetDigit(u32 a[], u32 d, size_t ndigits)
+{	/* Sets a = d where d is a single digit */
+	size_t i;
+
+	for (i = 1; i < ndigits; i++)
+	{
+		a[i] = 0;
+	}
+	a[0] = d;
+}
+
+u32 mpShiftLeft(u32 a[], const u32 *b,
+	size_t shift, size_t ndigits)
+{	/* Computes a = b << shift */
+	/* [v2.1] Modified to cope with shift > BITS_PERDIGIT */
+	size_t i, y, nw, bits;
+	u32 mask, carry, nextcarry;
+
+	/* Do we shift whole digits? */
+	if (shift >= BITS_PER_DIGIT)
+	{
+		nw = shift / BITS_PER_DIGIT;
+		i = ndigits;
+		while (i--)
+		{
+			if (i >= nw)
+				a[i] = b[i-nw];
+			else
+				a[i] = 0;
+		}
+		/* Call again to shift bits inside digits */
+		bits = shift % BITS_PER_DIGIT;
+		carry = b[ndigits-nw] << bits;
+		if (bits)
+			carry |= mpShiftLeft(a, a, bits, ndigits);
+		return carry;
+	}
+	else
+	{
+		bits = shift;
+	}
+
+	/* Construct mask = high bits set */
+	mask = ~(~(u32)0 >> bits);
+
+	y = BITS_PER_DIGIT - bits;
+	carry = 0;
+	for (i = 0; i < ndigits; i++)
+	{
+		nextcarry = (b[i] & mask) >> y;
+		a[i] = b[i] << bits | carry;
+		carry = nextcarry;
+	}
+
+	return carry;
+}
+
+u32 mpShiftRight(u32 a[], const u32 b[], size_t shift, size_t ndigits)
+{	/* Computes a = b >> shift */
+	/* [v2.1] Modified to cope with shift > BITS_PERDIGIT */
+	size_t i, y, nw, bits;
+	u32 mask, carry, nextcarry;
+
+	/* Do we shift whole digits? */
+	if (shift >= BITS_PER_DIGIT)
+	{
+		nw = shift / BITS_PER_DIGIT;
+		for (i = 0; i < ndigits; i++)
+		{
+			if ((i+nw) < ndigits)
+				a[i] = b[i+nw];
+			else
+				a[i] = 0;
+		}
+		/* Call again to shift bits inside digits */
+		bits = shift % BITS_PER_DIGIT;
+		carry = b[nw-1] >> bits;
+		if (bits)
+			carry |= mpShiftRight(a, a, bits, ndigits);
+		return carry;
+	}
+	else
+	{
+		bits = shift;
+	}
+
+	/* Construct mask to set low bits */
+	/* (thanks to Jesse Chisholm for suggesting this improved technique) */
+	mask = ~(~(u32)0 << bits);
+
+	y = BITS_PER_DIGIT - bits;
+	carry = 0;
+	i = ndigits;
+	while (i--)
+	{
+		nextcarry = (b[i] & mask) << y;
+		a[i] = b[i] >> bits | carry;
+		carry = nextcarry;
+	}
+
+	return carry;
+}
+
+u32 mpShortDiv(u32 q[], const u32 u[], u32 v,
+				   size_t ndigits)
+{
+	/*	Calculates quotient q = u div v
+		Returns remainder r = u mod v
+		where q, u are multiprecision integers of ndigits each
+		and r, v are single precision digits.
+
+		Makes no assumptions about normalisation.
+
+		Ref: Knuth Vol 2 Ch 4.3.1 Exercise 16 p625
+	*/
+	size_t j;
+	u32 t[2], r;
+	size_t shift;
+	u32 bitmask, overflow, *uu;
+
+	if (ndigits == 0) return 0;
+	if (v == 0)	return 0;	/* Divide by zero error */
+
+	/*	Normalise first */
+	/*	Requires high bit of V
+		to be set, so find most signif. bit then shift left,
+		i.e. d = 2^shift, u' = u * d, v' = v * d.
+	*/
+	bitmask = HIBITMASK;
+	for (shift = 0; shift < BITS_PER_DIGIT; shift++)
+	{
+		if (v & bitmask)
+			break;
+		bitmask >>= 1;
+	}
+
+	v <<= shift;
+	overflow = mpShiftLeft(q, u, shift, ndigits);
+	uu = q;
+
+	/* Step S1 - modified for extra digit. */
+	r = overflow;	/* New digit Un */
+	j = ndigits;
+	while (j--)
+	{
+		/* Step S2. */
+		t[1] = r;
+		t[0] = uu[j];
+		overflow = spDivide(&q[j], &r, t, v);
+	}
+
+	/* Unnormalise */
+	r >>= shift;
+
+	return r;
+}
+
+/** Returns sign of (a - d) where d is a single digit */
+int mpShortCmp(const u32 a[], u32 d, size_t ndigits)
+{
+	size_t i;
+	int gt = 0;
+	int lt = 0;
+
+	/* Zero-length a => a is zero */
+	if (ndigits == 0) return (d ? -1 : 0);
+
+	/* If |a| > 1 then a > d */
+	for (i = 1; i < ndigits; i++) {
+		if (a[i] != 0)
+			return 1;	/* GT */
+	}
+
+	lt = (a[0] < d);
+	gt = (a[0] > d);
+
+	return gt - lt;	/* EQ=0 GT=+1 LT=-1 */
+}
+
+int mpModulo(u32 r[], const u32 u[], size_t udigits,
+			 u32 v[], size_t vdigits)
+{
+	/*	Computes r = u mod v
+		where r, v are multiprecision integers of length vdigits
+		and u is a multiprecision integer of length udigits.
+		r may overlap v.
+
+		Note that r here is only vdigits long,
+		whereas in mpDivide it is udigits long.
+
+		Use remainder from mpDivide function.
+	*/
+	u32 *qq, *rr;
+
+	size_t nn = max(udigits, vdigits);
+	qq = kzalloc(udigits * sizeof(u32), GFP_KERNEL);
+	BUG_ON(!qq);
+	rr = kzalloc(nn * sizeof(u32), GFP_KERNEL);
+	BUG_ON(!rr);
+
+	/* rr[nn] = u mod v */
+	mpDivide(qq, rr, u, udigits, v, vdigits);
+
+	/* Final r is only vdigits long */
+	mpSetEqual(r, rr, vdigits);
+
+	kfree(rr);
+	kfree(qq);
+
+	return 0;
+}
+
+int mpModMult(u32 a[], const u32 x[], const u32 y[],
+			  u32 m[], size_t ndigits)
+{	/*	Computes a = (x * y) mod m */
+
+	/* Double-length temp variable p */
+	u32 *p;
+	p = kzalloc(ndigits * 2 * sizeof(u32), GFP_KERNEL);
+	BUG_ON(!p);
+
+	/* Calc p[2n] = x * y */
+	mpMultiply(p, x, y, ndigits);
+
+	/* Then modulo (NOTE: a is OK at only ndigits long) */
+	mpModulo(a, p, ndigits * 2, m, ndigits);
+
+	kfree(p);
+
+	return 0;
+}
+
+int mpModInv(u32 inv[], const u32 u[], const u32 v[], size_t ndigits)
+{	/*	Computes inv = u^(-1) mod v */
+	/*	Ref: Knuth Algorithm X Vol 2 p 342
+		ignoring u2, v2, t2
+		and avoiding negative numbers.
+		Returns non-zero if inverse undefined.
+	*/
+	int bIterations;
+	int result;
+
+	/* 1 * ndigits each, except w = 2 * ndigits */
+	u32 *u1, *u3, *v1, *v3, *t1, *t3, *q, *w;
+	/* allocate 9 * ndigits */
+	u1 = kzalloc(9 * ndigits * sizeof(u32), GFP_KERNEL);
+	BUG_ON(!u1);
+	u3 = &u1[1 * ndigits];
+	v1 = &u1[2 * ndigits];
+	v3 = &u1[3 * ndigits];
+	t1 = &u1[4 * ndigits];
+	t3 = &u1[5 * ndigits];
+	q  = &u1[6 * ndigits];
+	/* 2 * ndigits each */
+	w =  &u1[7 * ndigits];
+
+	/* Step X1. Initialise */
+	mpSetDigit(u1, 1, ndigits);		/* u1 = 1 */
+	mpSetEqual(u3, u, ndigits);		/* u3 = u */
+	mpSetZero(v1, ndigits);			/* v1 = 0 */
+	mpSetEqual(v3, v, ndigits);		/* v3 = v */
+
+	bIterations = 1;	/* Remember odd/even iterations */
+	while (!mpIsZero(v3, ndigits))		/* Step X2. Loop while v3 != 0 */
+	{					/* Step X3. Divide and "Subtract" */
+		mpDivide(q, t3, u3, ndigits, v3, ndigits);
+						/* q = u3 / v3, t3 = u3 % v3 */
+		mpMultiply(w, q, v1, ndigits);	/* w = q * v1 */
+		mpAdd(t1, u1, w, ndigits);		/* t1 = u1 + w */
+
+		/* Swap u1 = v1; v1 = t1; u3 = v3; v3 = t3 */
+		mpSetEqual(u1, v1, ndigits);
+		mpSetEqual(v1, t1, ndigits);
+		mpSetEqual(u3, v3, ndigits);
+		mpSetEqual(v3, t3, ndigits);
+
+		bIterations = -bIterations;
+	}
+
+	if (bIterations < 0)
+		mpSubtract(inv, v, u1, ndigits);	/* inv = v - u1 */
+	else
+		mpSetEqual(inv, u1, ndigits);	/* inv = u1 */
+
+	/* Make sure u3 = gcd(u,v) == 1 */
+	if (mpShortCmp(u3, 1, ndigits) != 0)
+	{
+		result = 1;
+		mpSetZero(inv, ndigits);
+	}
+	else
+		result = 0;
+
+	/* Clear up */
+	kfree(u1);
+
+	return result;
+}
+
+size_t mpConvFromOctets(u32 a[], size_t ndigits, const unsigned char *c, size_t nbytes)
+/* Converts nbytes octets into big digit a of max size ndigits
+   Returns actual number of digits set (may be larger than mpSizeof)
+*/
+{
+	size_t i;
+	int j, k;
+	u32 t;
+
+	mpSetZero(a, ndigits);
+
+	/* Read in octets, least significant first */
+	/* i counts into big_d, j along c, and k is # bits to shift */
+	for (i = 0, j = (int)nbytes - 1; i < ndigits && j >= 0; i++)
+	{
+		t = 0;
+		for (k = 0; j >= 0 && k < BITS_PER_DIGIT; j--, k += 8)
+			t |= ((u32)c[j]) << k;
+		a[i] = t;
+	}
+
+	return i;
+}
+
+size_t mpConvToOctets(const u32 a[], size_t ndigits, unsigned char *c, size_t nbytes)
+/* Convert big digit a into string of octets, in big-endian order,
+   padding on the left to nbytes or truncating if necessary.
+   Return number of octets required excluding leading zero bytes.
+*/
+{
+	int j, k, len;
+	u32 t;
+	size_t i, noctets, nbits;
+
+	nbits = mpBitLength(a, ndigits);
+	noctets = (nbits + 7) / 8;
+
+	len = (int)nbytes;
+
+	for (i = 0, j = len - 1; i < ndigits && j >= 0; i++)
+	{
+		t = a[i];
+		for (k = 0; j >= 0 && k < BITS_PER_DIGIT; j--, k += 8)
+			c[j] = (unsigned char)(t >> k);
+	}
+
+	for ( ; j >= 0; j--)
+		c[j] = 0;
+
+	return (size_t)noctets;
+}
+
+/* MACROS TO DO MODULAR SQUARING AND MULTIPLICATION USING PRE-ALLOCATED TEMPS */
+/* Required lengths |y|=|t1|=|t2|=2*n, |m|=n; but final |y|=n */
+/* Square: y = (y * y) mod m */
+#define mpMODSQUARETEMP(y,m,n,t1,t2) do{mpSquare(t1,y,n);mpDivide(t2,y,t1,n*2,m,n);}while(0)
+/* Mult:   y = (y * x) mod m */
+#define mpMODMULTTEMP(y,x,m,n,t1,t2) do{mpMultiply(t1,x,y,n);mpDivide(t2,y,t1,n*2,m,n);}while(0)
+/* Mult:   w = (y * x) mod m */
+#define mpMODMULTXYTEMP(w,y,x,m,n,t1,t2) do{mpMultiply(t1,x,y,(n));mpDivide(t2,w,t1,(n)*2,m,(n));}while(0)
+
+#define mpNEXTBITMASK(mask, n) do{if(mask==1){mask=HIBITMASK;n--;}else{mask>>=1;}}while(0)
+
+
+int mpModExp(u32 yout[], const u32 x[], const u32 e[], u32 m[], size_t ndigits)
+{	/*	Computes y = x^e mod m */
+	/*	"Classic" binary left-to-right method */
+	/*  [v2.2] removed const restriction on m[] to avoid using an extra alloc'd var
+		(m is changed in-situ during the divide operation then restored) */
+	u32 mask;
+	size_t n;
+	size_t nn = ndigits * 2;
+	/* Create some double-length temps */
+
+	u32 *t1, *t2, *y;
+	t1 = kzalloc(nn * 3 * sizeof(u32), GFP_KERNEL);
+	t2 = &t1[nn * 1];
+	y  = &t1[nn * 2];
+
+	assert(ndigits != 0);
+
+	n = mpSizeof(e, ndigits);
+	/* Catch e==0 => x^0=1 */
+	if (0 == n)
+	{
+		mpSetDigit(yout, 1, ndigits);
+		goto done;
+	}
+	/* Find second-most significant bit in e */
+	for (mask = HIBITMASK; mask > 0; mask >>= 1)
+	{
+		if (e[n-1] & mask)
+			break;
+	}
+	mpNEXTBITMASK(mask, n);
+
+	/* Set y = x */
+	mpSetEqual(y, x, ndigits);
+
+	/* For bit j = k-2 downto 0 */
+	while (n)
+	{
+		/* Square y = y * y mod n */
+		mpMODSQUARETEMP(y, m, ndigits, t1, t2);
+		if (e[n-1] & mask)
+		{	/*	if e(j) == 1 then multiply
+				y = y * x mod n */
+			mpMODMULTTEMP(y, x, m, ndigits, t1, t2);
+		}
+
+		/* Move to next bit */
+		mpNEXTBITMASK(mask, n);
+	}
+
+	/* Return y */
+	mpSetEqual(yout, y, ndigits);
+
+done:
+	kfree(t1);
+
+	return 0;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/bigdigits.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/bigdigits.h
@@ -0,0 +1,176 @@
+/* $Id: bigdigits.h $ */
+
+/** @file
+    Interface to core BigDigits "mp" functions using fixed-length arrays
+*/
+
+/***** BEGIN LICENSE BLOCK *****
+ *
+ * This Source Code Form is subject to the terms of the Mozilla Public
+ * License, v. 2.0. If a copy of the MPL was not distributed with this
+ * file, You can obtain one at http://mozilla.org/MPL/2.0/.
+ *
+ * Copyright (c) 2001-15 David Ireland, D.I. Management Services Pty Limited
+ * <http://www.di-mgt.com.au/bigdigits.html>. All rights reserved.
+  *
+ * Alternatively, the contents of this file may be used under the terms
+ * of the GNU General Public License Version 2, as described below:
+ * 
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+ ***** END LICENSE BLOCK *****/
+/*
+ * Last updated:
+ * $Date: 2015-10-22 10:23:00 $
+ * $Revision: 2.5.0 $
+ * $Author: dai $
+ */
+
+#ifndef BIGDIGITS_H_
+#define BIGDIGITS_H_ 1
+
+#include <linux/types.h>
+
+/* Sizes to match */
+#define MAX_DIGIT 0xFFFFFFFFUL
+#define BITS_PER_DIGIT 32
+#define HIBITMASK 0x80000000UL
+
+volatile char *copyright_notice(void);
+	/* Forces linker to include copyright notice in executable */
+/** @endcond */
+
+/** Computes w = u + v, returns carry */
+u32 mpAdd(u32 w[], const u32 u[], const u32 v[], size_t ndigits);
+
+/** Computes w = u - v, returns borrow */
+u32 mpSubtract(u32 w[], const u32 u[], const u32 v[], size_t ndigits);
+
+/** Computes product w = u * v
+@param[out] w To receive the product, an array of size 2 x `ndigits`
+@param[in] u An array of size `ndigits`
+@param[in] v An array of size `ndigits`
+@param[in] ndigits size of arrays `u` and `v`
+@warning The product must be of size 2 x `ndigits`
+*/
+int mpMultiply(u32 w[], const u32 u[], const u32 v[], size_t ndigits);
+
+/** Computes integer division of u by v such that u=qv+r
+@param[out] q to receive quotient = u div v, an array of size `udigits`
+@param[out] r to receive divisor = u mod v, an array of size `udigits`
+@param[in]  u dividend of size `udigits`
+@param[in] udigits size of arrays `q` `r` and `u`
+@param[in]  v divisor of size `vdigits`
+@param[in] vdigits size of array `v`
+@warning Trashes q and r first
+*/
+int mpDivide(u32 q[], u32 r[], const u32 u[],
+	size_t udigits, u32 v[], size_t vdigits);
+
+
+/** Computes remainder r = u mod v
+@param[out] r to receive divisor = u mod v, an array of size `vdigits`
+@param[in]  u dividend of size `udigits`
+@param[in] udigits size of arrays `r` and `u`
+@param[in]  v divisor of size `vdigits`
+@param[in] vdigits size of array `v`
+@remark Note that `r` is `vdigits` long here, but is `udigits` long in mpDivide().
+*/
+int mpModulo(u32 r[], const u32 u[], size_t udigits, u32 v[], size_t vdigits);
+
+/** Computes square w = x^2
+@param[out] w array of size 2 x `ndigits` to receive square
+@param[in] x array of size `ndigits`
+@param[in] ndigits size of array `x`
+@warning The product `w` must be of size 2 x `ndigits`
+*/
+int mpSquare(u32 w[], const u32 x[], size_t ndigits);
+
+/** Returns true if a is zero, else false, using constant-time algorithm
+ *  @remark Constant-time with respect to `ndigits`
+ */
+int mpIsZero(const u32 a[], size_t ndigits);
+
+/*************************/
+/* COMPARISON OPERATIONS */
+/*************************/
+/* [v2.5] Changed to constant-time algorithms */
+
+/** Returns true if a == b, else false, using constant-time algorithm
+ *  @remark Constant-time with respect to `ndigits`
+ */
+int mpEqual(const u32 a[], const u32 b[], size_t ndigits);
+
+/** Returns sign of `(a-b)` as `{-1,0,+1}` using constant-time algorithm
+ *  @remark Constant-time with respect to `ndigits`
+ */
+int mpCompare(const u32 a[], const u32 b[], size_t ndigits);
+
+/** Returns true if a is zero, else false, using constant-time algorithm
+ *  @remark Constant-time with respect to `ndigits`
+ */
+int mpIsZero(const u32 a[], size_t ndigits);
+
+/** Computes a = (x * y) mod m */
+int mpModMult(u32 a[], const u32 x[], const u32 y[], u32 m[], size_t ndigits);
+
+/** Computes the inverse of `u` modulo `m`, inv = u^{-1} mod m */
+int mpModInv(u32 inv[], const u32 u[], const u32 m[], size_t ndigits);
+
+/** Returns number of significant bits in a */
+size_t mpBitLength(const u32 a[], size_t ndigits);
+
+/** Computes a = b << x */
+u32 mpShiftLeft(u32 a[], const u32 b[], size_t x, size_t ndigits);
+
+/** Computes a = b >> x */
+u32 mpShiftRight(u32 a[], const u32 b[], size_t x, size_t ndigits);
+
+/** Sets bit n of a (0..nbits-1) with value 1 or 0 */
+int mpSetBit(u32 a[], size_t ndigits, size_t n, int value);
+
+/** Sets a = 0 */
+volatile u32 mpSetZero(volatile u32 a[], size_t ndigits);
+
+/** Sets a = d where d is a single digit */
+void mpSetDigit(u32 a[], u32 d, size_t ndigits);
+
+/** Sets a = b */
+void mpSetEqual(u32 a[], const u32 b[], size_t ndigits);
+
+/** Returns value 1 or 0 of bit n (0..nbits-1) */
+int mpGetBit(u32 a[], size_t ndigits, size_t n);
+
+/** Returns number of significant non-zero digits in a */
+size_t mpSizeof(const u32 a[], size_t ndigits);
+
+/** Computes quotient q = u div d, returns remainder */
+u32 mpShortDiv(u32 q[], const u32 u[], u32 d, size_t ndigits);
+
+/** Returns sign of (a - d) where d is a single digit */
+int mpShortCmp(const u32 a[], u32 d, size_t ndigits);
+
+/** Computes p = x * y, where x and y are single digits */
+int spMultiply(u32 p[2], u32 x, u32 y);
+
+/** Computes quotient q = u div v, remainder r = u mod v, where q, r and v are single digits */
+u32 spDivide(u32 *q, u32 *r, const u32 u[2], u32 v);
+
+size_t mpConvFromOctets(u32 a[], size_t ndigits, const unsigned char *c, size_t nbytes);
+/** Converts big digit a into string of octets, in big-endian order, padding to nbytes or truncating if necessary.
+@returns number of non-zero octets required. */
+size_t mpConvToOctets(const u32 a[], size_t ndigits, unsigned char *c, size_t nbytes);
+
+/** Computes y = x^e mod m */
+int mpModExp(u32 y[], const u32 x[], const u32 e[], u32 m[], size_t ndigits);
+
+/** @endcond */
+
+#endif	/* BIGDIGITS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/hmac.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/hmac.c
@@ -0,0 +1,147 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file hmac.c
+*
+* This file contains the implementation of the HMAC Hash Message
+* Authentication Code.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+*</pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files *********************************/
+#include <linux/types.h>
+#include <linux/math64.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+
+#include "xil_types.h"
+#include "xstatus.h"
+
+#include "xhdcp22_common.h"
+
+/************************** Constant Definitions *****************************/
+#define SHA256_SIZE		256/8	/**< SHA256 Hash size */
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function does a HMAC_SHA256 transform:
+* SHA256(K XOR opad, SHA256(K XOR ipad, text))
+*
+* ipad is the byte 0x36 repeated 64 times
+* opad is the byte 0x5c repeated 64 times
+* and text is the data being protected
+*
+* @param	Data is the input data.
+* @param	DataSize is the size of the data buffer.
+* @param	Key is the hash-key to use.
+* @param	KeySize is the size of the hash key.
+* @param	HashedData is the output of this function.
+*
+* @return	- XST_SUCCESS if no errors occured
+*			- XST_FAILURE if the datasize execeeds the size of the local buffer.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp22Cmn_HmacSha256Hash(const u8 *Data, int DataSize, const u8 *Key, int KeySize, u8  *HashedData)
+{
+#if 0
+	u8 Ipad[65];   /* inner padding-key XORd with ipad */
+	u8 Opad[65];   /* outer padding-key XORd with opad */
+	u8 Ktemp[SHA256_SIZE];
+	u8 Ktemp2[SHA256_SIZE];
+	u8 BufferIn[256];
+	u8 BufferOut[256];
+	int i;
+
+	memset(BufferIn, 0x00, 256);
+	memset(BufferOut, 0x00, 256);
+#endif
+	u8 *Ipad, *Opad, *Ktemp, *Ktemp2, *BufferIn, *BufferOut;
+	Ipad = kzalloc(65, GFP_KERNEL);
+	Opad = kzalloc(65, GFP_KERNEL);
+	Ktemp = kzalloc(SHA256_SIZE, GFP_KERNEL);
+	Ktemp2 = kzalloc(SHA256_SIZE, GFP_KERNEL);
+	BufferIn = kzalloc(256, GFP_KERNEL);
+	BufferOut = kzalloc(256, GFP_KERNEL);
+	int i;
+
+	/* If the input size exceeds the local buffers, return an error */
+	if(DataSize + 64 >  256) {
+		return XST_FAILURE;
+	}
+
+	/* If key is longer than 64 bytes reset it to Key=sha256(Key) */
+	if(KeySize > 64) {
+		XHdcp22Cmn_Sha256Hash(Key, KeySize, Ktemp );
+		Key     = Ktemp;
+		KeySize = SHA256_SIZE;
+	}
+
+	/* start out by storing Key in pads */
+#if 0
+	memset(Ipad, 0, sizeof Ipad );
+	memset(Opad, 0, sizeof Opad );
+#endif
+	memcpy(Ipad, Key, KeySize );
+	memcpy(Opad, Key, KeySize );
+
+	/* XOR Key with Ipad and Opad values */
+	for(i = 0; i < 64; i++) {
+		Ipad[i] ^= 0x36;
+		Opad[i] ^= 0x5c;
+	}
+
+	/* Execute inner SHA256 */
+	memcpy(BufferIn, Ipad, 64 );
+	memcpy(BufferIn + 64, Data, DataSize );
+	XHdcp22Cmn_Sha256Hash(BufferIn, 64 + DataSize, Ktemp2 );
+
+	/* Execute outer SHA256 */
+	memcpy(BufferOut, Opad, 64);
+	memcpy(BufferOut + 64, Ktemp2, SHA256_SIZE );
+	XHdcp22Cmn_Sha256Hash(BufferOut, 64 + SHA256_SIZE,
+						(u8 *)HashedData );
+
+	kfree(BufferOut);
+	kfree(BufferIn);
+	kfree(Ktemp);
+	kfree(Ktemp2);
+	kfree(Opad);
+	kfree(Ipad);
+
+	return XST_SUCCESS;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sha1.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sha1.c
@@ -0,0 +1,406 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*
+ *  sha1.c
+ *
+ *  Description:
+ *      This file implements the Secure Hashing Algorithm 1 as
+ *      defined in FIPS PUB 180-1 published April 17, 1995.
+ *
+ *      The SHA-1, produces a 160-bit message digest for a given
+ *      data stream.  It should take about 2**n steps to find a
+ *      message with the same digest as a given message and
+ *      2**(n/2) to find any two messages with the same digest,
+ *      when n is the digest size in bits.  Therefore, this
+ *      algorithm can serve as a means of providing a
+ *      "fingerprint" for a message.
+ *
+ *  Portability Issues:
+ *      SHA-1 is defined in terms of 32-bit "words".  This code
+ *      uses <stdint.h> (included via "sha1.h" to define 32 and 8
+ *      bit unsigned integer types.  If your C compiler does not
+ *      support 32 bit unsigned integers, this code is not
+ *      appropriate.
+ *
+ *  Caveats:
+ *      SHA-1 is designed to work with messages less than 2^64 bits
+ *      long.  Although SHA-1 allows a message digest to be generated
+ *      for messages of any number of bits less than 2^64, this
+ *      implementation only works with messages with a length that is
+ *      a multiple of the size of an 8-bit character.
+ *
+ */
+
+#include "sha1.h"
+
+/*
+ *  Define the SHA1 circular left shift macro
+ */
+#define SHA1CircularShift(bits,word) \
+                (((word) << (bits)) | ((word) >> (32-(bits))))
+
+/* Local Function Prototyptes */
+void SHA1PadMessage(SHA1Context *);
+void SHA1ProcessMessageBlock(SHA1Context *);
+
+/*
+ *  SHA1Reset
+ *
+ *  Description:
+ *      This function will initialize the SHA1Context in preparation
+ *      for computing a new SHA1 message digest.
+ *
+ *  Parameters:
+ *      context: [in/out]
+ *          The context to reset.
+ *
+ *  Returns:
+ *      sha Error Code.
+ *
+ */
+int SHA1Reset(SHA1Context *context)
+{
+    if (!context)
+    {
+        return shaNull;
+    }
+
+    context->Length_Low             = 0;
+    context->Length_High            = 0;
+    context->Message_Block_Index    = 0;
+
+    memset(context->Message_Block, 0, 64);
+
+    context->Intermediate_Hash[0]   = 0x67452301;
+    context->Intermediate_Hash[1]   = 0xEFCDAB89;
+    context->Intermediate_Hash[2]   = 0x98BADCFE;
+    context->Intermediate_Hash[3]   = 0x10325476;
+    context->Intermediate_Hash[4]   = 0xC3D2E1F0;
+
+    context->Computed   = 0;
+    context->Corrupted  = 0;
+
+    return shaSuccess;
+}
+
+/*
+ *  SHA1Result
+ *
+ *  Description:
+ *      This function will return the 160-bit message digest into the
+ *      Message_Digest array  provided by the caller.
+ *      NOTE: The first octet of hash is stored in the 0th element,
+ *            the last octet of hash in the 19th element.
+ *
+ *  Parameters:
+ *      context: [in/out]
+ *          The context to use to calculate the SHA-1 hash.
+ *      Message_Digest: [out]
+ *          Where the digest is returned.
+ *
+ *  Returns:
+ *      sha Error Code.
+ *
+ */
+int SHA1Result( SHA1Context *context,
+                u8 Message_Digest[SHA1HashSize])
+{
+    int i;
+
+    if (!context || !Message_Digest)
+    {
+        return shaNull;
+    }
+
+    if (context->Corrupted)
+    {
+        return context->Corrupted;
+    }
+
+    if (!context->Computed)
+    {
+        SHA1PadMessage(context);
+        for(i=0; i<64; ++i)
+        {
+            /* message may be sensitive, clear it out */
+            context->Message_Block[i] = 0;
+        }
+        context->Length_Low = 0;    /* and clear length */
+        context->Length_High = 0;
+        context->Computed = 1;
+
+    }
+
+    for(i = 0; i < SHA1HashSize; ++i)
+    {
+        Message_Digest[i] = context->Intermediate_Hash[i>>2]
+                            >> 8 * ( 3 - ( i & 0x03 ) );
+    }
+
+    return shaSuccess;
+}
+
+/*
+ *  SHA1Input
+ *
+ *  Description:
+ *      This function accepts an array of octets as the next portion
+ *      of the message.
+ *
+ *  Parameters:
+ *      context: [in/out]
+ *          The SHA context to update
+ *      message_array: [in]
+ *          An array of characters representing the next portion of
+ *          the message.
+ *      length: [in]
+ *          The length of the message in message_array
+ *
+ *  Returns:
+ *      sha Error Code.
+ *
+ */
+int SHA1Input(    SHA1Context    *context,
+                  const u8  *message_array,
+                  unsigned       length)
+{
+    if (!length)
+    {
+        return shaSuccess;
+    }
+
+    if (!context || !message_array)
+    {
+        return shaNull;
+    }
+
+    if (context->Computed)
+    {
+        context->Corrupted = shaStateError;
+
+        return shaStateError;
+    }
+
+    if (context->Corrupted)
+    {
+         return context->Corrupted;
+    }
+    while(length-- && !context->Corrupted)
+    {
+    context->Message_Block[context->Message_Block_Index++] =
+                    (*message_array & 0xFF);
+
+    context->Length_Low += 8;
+    if (context->Length_Low == 0)
+    {
+        context->Length_High++;
+        if (context->Length_High == 0)
+        {
+            /* Message is too long */
+            context->Corrupted = 1;
+        }
+    }
+
+    if (context->Message_Block_Index == 64)
+    {
+        SHA1ProcessMessageBlock(context);
+    }
+
+    message_array++;
+    }
+
+    return shaSuccess;
+}
+
+/*
+ *  SHA1ProcessMessageBlock
+ *
+ *  Description:
+ *      This function will process the next 512 bits of the message
+ *      stored in the Message_Block array.
+ *
+ *  Parameters:
+ *      None.
+ *
+ *  Returns:
+ *      Nothing.
+ *
+ *  Comments:
+
+ *      Many of the variable names in this code, especially the
+ *      single character names, were used because those were the
+ *      names used in the publication.
+ *
+ *
+ */
+void SHA1ProcessMessageBlock(SHA1Context *context)
+{
+    const u32 K[] =    {       /* Constants defined in SHA-1   */
+                            0x5A827999,
+                            0x6ED9EBA1,
+                            0x8F1BBCDC,
+                            0xCA62C1D6
+                            };
+    int           t;                 /* Loop counter                */
+    u32      temp;              /* Temporary word value        */
+    u32      W[80];             /* Word sequence               */
+    u32      A, B, C, D, E;     /* Word buffers                */
+
+    /*
+     *  Initialize the first 16 words in the array W
+     */
+    for(t = 0; t < 16; t++)
+    {
+        W[t] = context->Message_Block[t * 4] << 24;
+        W[t] |= context->Message_Block[t * 4 + 1] << 16;
+        W[t] |= context->Message_Block[t * 4 + 2] << 8;
+        W[t] |= context->Message_Block[t * 4 + 3];
+    }
+
+    for(t = 16; t < 80; t++)
+    {
+       W[t] = SHA1CircularShift(1,W[t-3] ^ W[t-8] ^ W[t-14] ^ W[t-16]);
+    }
+
+    A = context->Intermediate_Hash[0];
+    B = context->Intermediate_Hash[1];
+    C = context->Intermediate_Hash[2];
+    D = context->Intermediate_Hash[3];
+    E = context->Intermediate_Hash[4];
+
+    for(t = 0; t < 20; t++)
+    {
+        temp =  SHA1CircularShift(5,A) +
+                ((B & C) | ((~B) & D)) + E + W[t] + K[0];
+        E = D;
+        D = C;
+        C = SHA1CircularShift(30,B);
+
+        B = A;
+        A = temp;
+    }
+
+    for(t = 20; t < 40; t++)
+    {
+        temp = SHA1CircularShift(5,A) + (B ^ C ^ D) + E + W[t] + K[1];
+        E = D;
+        D = C;
+        C = SHA1CircularShift(30,B);
+        B = A;
+        A = temp;
+    }
+
+    for(t = 40; t < 60; t++)
+    {
+        temp = SHA1CircularShift(5,A) +
+               ((B & C) | (B & D) | (C & D)) + E + W[t] + K[2];
+        E = D;
+        D = C;
+        C = SHA1CircularShift(30,B);
+        B = A;
+        A = temp;
+    }
+
+    for(t = 60; t < 80; t++)
+    {
+        temp = SHA1CircularShift(5,A) + (B ^ C ^ D) + E + W[t] + K[3];
+        E = D;
+        D = C;
+        C = SHA1CircularShift(30,B);
+        B = A;
+        A = temp;
+    }
+
+    context->Intermediate_Hash[0] += A;
+    context->Intermediate_Hash[1] += B;
+    context->Intermediate_Hash[2] += C;
+    context->Intermediate_Hash[3] += D;
+    context->Intermediate_Hash[4] += E;
+
+    context->Message_Block_Index = 0;
+}
+
+/*
+ *  SHA1PadMessage
+ *
+
+ *  Description:
+ *      According to the standard, the message must be padded to an even
+ *      512 bits.  The first padding bit must be a '1'.  The last 64
+ *      bits represent the length of the original message.  All bits in
+ *      between should be 0.  This function will pad the message
+ *      according to those rules by filling the Message_Block array
+ *      accordingly.  It will also call the ProcessMessageBlock function
+ *      provided appropriately.  When it returns, it can be assumed that
+ *      the message digest has been computed.
+ *
+ *  Parameters:
+ *      context: [in/out]
+ *          The context to pad
+ *      ProcessMessageBlock: [in]
+ *          The appropriate SHA*ProcessMessageBlock function
+ *  Returns:
+ *      Nothing.
+ *
+ */
+
+void SHA1PadMessage(SHA1Context *context)
+{
+    /*
+     *  Check to see if the current message block is too small to hold
+     *  the initial padding bits and length.  If so, we will pad the
+     *  block, process it, and then continue padding into a second
+     *  block.
+     */
+    if (context->Message_Block_Index > 55)
+    {
+        context->Message_Block[context->Message_Block_Index++] = 0x80;
+        while(context->Message_Block_Index < 64)
+        {
+            context->Message_Block[context->Message_Block_Index++] = 0;
+        }
+
+        SHA1ProcessMessageBlock(context);
+
+        while(context->Message_Block_Index < 56)
+        {
+            context->Message_Block[context->Message_Block_Index++] = 0;
+        }
+    }
+    else
+    {
+        context->Message_Block[context->Message_Block_Index++] = 0x80;
+        while(context->Message_Block_Index < 56)
+        {
+
+            context->Message_Block[context->Message_Block_Index++] = 0;
+        }
+    }
+
+    /*
+     *  Store the message length as the last 8 octets
+     */
+    context->Message_Block[56] = context->Length_High >> 24;
+    context->Message_Block[57] = context->Length_High >> 16;
+    context->Message_Block[58] = context->Length_High >> 8;
+    context->Message_Block[59] = context->Length_High;
+    context->Message_Block[60] = context->Length_Low >> 24;
+    context->Message_Block[61] = context->Length_Low >> 16;
+    context->Message_Block[62] = context->Length_Low >> 8;
+    context->Message_Block[63] = context->Length_Low;
+
+    SHA1ProcessMessageBlock(context);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sha1.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sha1.h
@@ -0,0 +1,88 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*
+ *  sha1.h
+ *
+ *  Description:
+ *      This is the header file for code which implements the Secure
+ *      Hashing Algorithm 1 as defined in FIPS PUB 180-1 published
+ *      April 17, 1995.
+ *
+ *      Many of the variable names in this code, especially the
+ *      single character names, were used because those were the names
+ *      used in the publication.
+ *
+ *      Please read the file sha1.c for more information.
+ *
+ */
+
+#ifndef _SHA1_H_
+#define _SHA1_H_
+
+#include <linux/types.h>
+#include <linux/string.h>
+/*
+ * If you do not have the ISO standard stdint.h header file, then you
+ * must typdef the following:
+ *    name              meaning
+ *  uint32_t         unsigned 32 bit integer
+ *  uint8_t          unsigned 8 bit integer (i.e., unsigned char)
+ *  int    integer of >= 16 bits
+ *
+ */
+
+#ifndef _SHA_enum_
+#define _SHA_enum_
+enum
+{
+    shaSuccess = 0,
+    shaNull,            /* Null pointer parameter */
+    shaInputTooLong,    /* input data too long */
+    shaStateError       /* called Input after Result */
+};
+#endif
+#define SHA1HashSize 20
+
+/**
+ *  This structure will hold context information for the SHA-1
+ *  hashing operation
+ */
+typedef struct SHA1Context
+{
+    uint32_t Intermediate_Hash[SHA1HashSize/4];    /**< Message Digest       */
+
+    uint32_t Length_Low;               /**< Message length in bits           */
+    uint32_t Length_High;              /**< Message length in bits           */
+
+    int Message_Block_Index; /**< Index into message block array   */
+    uint8_t Message_Block[64];         /**< 512-bit message blocks           */
+
+    int Computed;                      /**< Is the digest computed?          */
+    int Corrupted;                     /**< Is the message digest corrupted? */
+} SHA1Context;
+
+/*
+ *  Function Prototypes
+ */
+
+int SHA1Reset(  SHA1Context *);
+int SHA1Input(  SHA1Context *,
+                const uint8_t *,
+                unsigned int);
+int SHA1Result( SHA1Context *,
+                uint8_t Message_Digest[SHA1HashSize]);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sha2.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sha2.c
@@ -0,0 +1,270 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file sha2.c
+*
+* This file contains the implementation of the SHA-2 Secure Hashing Algorithm.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+* 1.10  GM   10/14/19 Added "volatile" attribute to all "i" variables
+*</pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files ********************************/
+#include <linux/string.h>
+#include "xil_types.h"
+
+/**************************** Type Definitions ******************************/
+typedef struct {
+   u8 data[64];
+   u32 datalen;
+   u32 bitlen[2];
+   u32 state[8];
+} Sha256Type;
+
+/***************** Macros (Inline Functions) Definitions ********************/
+// DBL_INT_ADD treats two unsigned ints a and b as one 64-bit integer and adds c to it
+#define DBL_INT_ADD(a,b,c) if (a > 0xffffffff - (c)) ++b; a += c;
+#define ROTLEFT(a,b) (((a) << (b)) | ((a) >> (32-(b))))
+#define ROTRIGHT(a,b) (((a) >> (b)) | ((a) << (32-(b))))
+
+#define CH(x,y,z) (((x) & (y)) ^ (~(x) & (z)))
+#define MAJ(x,y,z) (((x) & (y)) ^ ((x) & (z)) ^ ((y) & (z)))
+#define EP0(x) (ROTRIGHT(x,2) ^ ROTRIGHT(x,13) ^ ROTRIGHT(x,22))
+#define EP1(x) (ROTRIGHT(x,6) ^ ROTRIGHT(x,11) ^ ROTRIGHT(x,25))
+#define SIG0(x) (ROTRIGHT(x,7) ^ ROTRIGHT(x,18) ^ ((x) >> 3))
+#define SIG1(x) (ROTRIGHT(x,17) ^ ROTRIGHT(x,19) ^ ((x) >> 10))
+
+/************************** Variable Definitions ****************************/
+static const u32 k[64] = {
+   0x428a2f98,0x71374491,0xb5c0fbcf,0xe9b5dba5,0x3956c25b,0x59f111f1,0x923f82a4,0xab1c5ed5,
+   0xd807aa98,0x12835b01,0x243185be,0x550c7dc3,0x72be5d74,0x80deb1fe,0x9bdc06a7,0xc19bf174,
+   0xe49b69c1,0xefbe4786,0x0fc19dc6,0x240ca1cc,0x2de92c6f,0x4a7484aa,0x5cb0a9dc,0x76f988da,
+   0x983e5152,0xa831c66d,0xb00327c8,0xbf597fc7,0xc6e00bf3,0xd5a79147,0x06ca6351,0x14292967,
+   0x27b70a85,0x2e1b2138,0x4d2c6dfc,0x53380d13,0x650a7354,0x766a0abb,0x81c2c92e,0x92722c85,
+   0xa2bfe8a1,0xa81a664b,0xc24b8b70,0xc76c51a3,0xd192e819,0xd6990624,0xf40e3585,0x106aa070,
+   0x19a4c116,0x1e376c08,0x2748774c,0x34b0bcb5,0x391c0cb3,0x4ed8aa4a,0x5b9cca4f,0x682e6ff3,
+   0x748f82ee,0x78a5636f,0x84c87814,0x8cc70208,0x90befffa,0xa4506ceb,0xbef9a3f7,0xc67178f2
+};
+
+/************************** Function Prototypes *****************************/
+
+/* SHA-256 Hashing */
+static void Sha256Transform(Sha256Type *Ctx, u8 *Data);
+static void Sha256Init(Sha256Type *Ctx);
+static void Sha256Update(Sha256Type *Ctx, const u8 *Data, u32 Len);
+static void Sha256Final(Sha256Type *Ctx, u8 *Hash);
+
+/************************** Function Implementation *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function computes a SHA256 hash on a array of data.
+*
+* @param  Data is the data on which a hash is calculated.
+* @param  DataSize is the size of the data array..
+* @param  HashedData is a 256-bits size hash.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Cmn_Sha256Hash(const u8 *Data, u32 DataSize, u8 *HashedData)
+{
+	Sha256Type Ctx;
+
+	Sha256Init(&Ctx);
+
+	Sha256Update(&Ctx, Data, DataSize);
+	Sha256Final(&Ctx, HashedData);
+}
+
+/*****************************************************************************/
+/**
+* This function executes a SHA256 transformation.
+*
+* @param  Ctx is the context data for SHA256.
+* @param  Data is the data to transform.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void Sha256Transform(Sha256Type *Ctx, u8 *Data)
+{
+  volatile u32 i;
+  u32 a,b,c,d,e,f,g,h,j,t1,t2,m[64];
+
+   for (i=0,j=0; i < 16; ++i, j += 4)
+      m[i] = (Data[j] << 24) | (Data[j+1] << 16) | (Data[j+2] << 8) | (Data[j+3]);
+   for ( ; i < 64; ++i)
+      m[i] = SIG1(m[i-2]) + m[i-7] + SIG0(m[i-15]) + m[i-16];
+
+   a = Ctx->state[0];
+   b = Ctx->state[1];
+   c = Ctx->state[2];
+   d = Ctx->state[3];
+   e = Ctx->state[4];
+   f = Ctx->state[5];
+   g = Ctx->state[6];
+   h = Ctx->state[7];
+
+   for (i = 0; i < 64; ++i) {
+      t1 = h + EP1(e) + CH(e,f,g) + k[i] + m[i];
+      t2 = EP0(a) + MAJ(a,b,c);
+      h = g;
+      g = f;
+      f = e;
+      e = d + t1;
+      d = c;
+      c = b;
+      b = a;
+      a = t1 + t2;
+   }
+
+   Ctx->state[0] += a;
+   Ctx->state[1] += b;
+   Ctx->state[2] += c;
+   Ctx->state[3] += d;
+   Ctx->state[4] += e;
+   Ctx->state[5] += f;
+   Ctx->state[6] += g;
+   Ctx->state[7] += h;
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the context data for a SHA 256 hash calculation.
+*
+* @param  Ctx is the context data for SHA256.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void Sha256Init(Sha256Type *Ctx)
+{
+   Ctx->datalen = 0;
+   Ctx->bitlen[0] = 0;
+   Ctx->bitlen[1] = 0;
+   Ctx->state[0] = 0x6a09e667;
+   Ctx->state[1] = 0xbb67ae85;
+   Ctx->state[2] = 0x3c6ef372;
+   Ctx->state[3] = 0xa54ff53a;
+   Ctx->state[4] = 0x510e527f;
+   Ctx->state[5] = 0x9b05688c;
+   Ctx->state[6] = 0x1f83d9ab;
+   Ctx->state[7] = 0x5be0cd19;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function updates the SHA data before adding padding data.
+*
+* @param  Ctx is the context data for SHA256.
+* @param  Data is the input data.
+* @param  Len is size of the input data array.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void Sha256Update(Sha256Type *Ctx, const u8 *Data, u32 Len)
+{
+   volatile u32 i;
+
+   for (i=0; i < Len; ++i) {
+      Ctx->data[Ctx->datalen] = Data[i];
+      Ctx->datalen++;
+      if (Ctx->datalen == 64) {
+	  Sha256Transform(Ctx,Ctx->data);
+         DBL_INT_ADD(Ctx->bitlen[0],Ctx->bitlen[1],512);
+         Ctx->datalen = 0;
+      }
+   }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function adds padding
+*
+* @param  Ctx is the context data for SHA256.
+* @param  Hash is the calculated hash (256-bits).
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void Sha256Final(Sha256Type *Ctx, u8 *Hash)
+{
+   volatile u32 i;
+
+   i = Ctx->datalen;
+
+   // Pad whatever data is left in the buffer.
+   if (Ctx->datalen < 56) {
+      Ctx->data[i++] = 0x80;
+      while (i < 56)
+         Ctx->data[i++] = 0x00;
+   }
+   else {
+      Ctx->data[i++] = 0x80;
+      while (i < 64)
+         Ctx->data[i++] = 0x00;
+      Sha256Transform(Ctx,Ctx->data);
+      memset(Ctx->data,0,56);
+   }
+
+   // Append to the padding the total message's length in bits and transform.
+   DBL_INT_ADD(Ctx->bitlen[0],Ctx->bitlen[1],Ctx->datalen * 8);
+   Ctx->data[63] = Ctx->bitlen[0];
+   Ctx->data[62] = Ctx->bitlen[0] >> 8;
+   Ctx->data[61] = Ctx->bitlen[0] >> 16;
+   Ctx->data[60] = Ctx->bitlen[0] >> 24;
+   Ctx->data[59] = Ctx->bitlen[1];
+   Ctx->data[58] = Ctx->bitlen[1] >> 8;
+   Ctx->data[57] = Ctx->bitlen[1] >> 16;
+   Ctx->data[56] = Ctx->bitlen[1] >> 24;
+   Sha256Transform(Ctx,Ctx->data);
+
+   // Since this implementation uses little endian byte ordering and SHA uses big endian,
+   // reverse all the bytes when copying the final state to the output hash.
+   for (i=0; i < 4; ++i) {
+      Hash[i]    = (Ctx->state[0] >> (24-i*8)) & 0x000000ff;
+      Hash[i+4]  = (Ctx->state[1] >> (24-i*8)) & 0x000000ff;
+      Hash[i+8]  = (Ctx->state[2] >> (24-i*8)) & 0x000000ff;
+      Hash[i+12] = (Ctx->state[3] >> (24-i*8)) & 0x000000ff;
+      Hash[i+16] = (Ctx->state[4] >> (24-i*8)) & 0x000000ff;
+      Hash[i+20] = (Ctx->state[5] >> (24-i*8)) & 0x000000ff;
+      Hash[i+24] = (Ctx->state[6] >> (24-i*8)) & 0x000000ff;
+      Hash[i+28] = (Ctx->state[7] >> (24-i*8)) & 0x000000ff;
+   }
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sleep.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/sleep.h
@@ -0,0 +1,34 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+
+#ifndef SLEEP_H
+#define SLEEP_H
+
+#include "xil_types.h"
+#include "xil_io.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+int usleep(unsigned long useconds);
+unsigned sleep(unsigned int seconds);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xdebug.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xdebug.c
@@ -0,0 +1,90 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+#include <linux/kernel.h>
+#include <stdarg.h>
+#include "xil_types.h"
+#include "xdebug.h"
+
+void XHdcp1x_SetDebugPrintf(XDebug_Printf PrintfFunc);
+
+XDebug_Printf xdebugPrintf = NULL;	/**< Instance of function
+											  *  interface used for debug
+											  *  print statement */
+
+char *xdebugBuff = NULL;
+int xdebugBuffSize = 0;
+int *xdebugBuffPos = NULL;
+
+static void XDebug_DebugBufPrintf(const char *fmt, ...)
+{
+	if(xdebugBuff != NULL)
+	{
+		va_list args;
+		va_start(args, fmt);
+		*xdebugBuffPos += vscnprintf(xdebugBuff + *xdebugBuffPos,
+				xdebugBuffSize - *xdebugBuffPos, fmt, args);
+		va_end(args);
+	}
+}
+
+
+/*****************************************************************************/
+/**
+* This function sets the debug printf function for the module to print to the
+* supplied buffer.
+*
+* @param	buff is the buffer to print to.
+* @param	buff_size is the maximum size of the buffer
+* @param	buff_pos is the current (and will be updated) position in the buffer
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XDebug_SetDebugBufPrintf(char *buff, int buff_size, int *buff_pos)
+{
+	if(buff)
+	{
+		xdebugBuff = buff;
+		xdebugBuffSize = buff_size;
+		xdebugBuffPos = buff_pos;
+		XDebug_SetDebugPrintf(XDebug_DebugBufPrintf);
+	} else {
+		XDebug_SetDebugPrintf(NULL);
+		xdebugBuff = NULL;
+		xdebugBuffSize = 0;
+		xdebugBuffPos = NULL;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the debug printf function for the module.
+*
+* @param	PrintfFunc is the printf function.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XDebug_SetDebugPrintf(XDebug_Printf PrintfFunc)
+{
+	xdebugPrintf = PrintfFunc;
+}
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xdebug.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xdebug.h
@@ -0,0 +1,65 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+
+#ifndef XDEBUG  /* prevent circular inclusions */
+#define XDEBUG  /* by using protection macros */
+
+/**
+ * This typedef defines the function interface that is to be used for debug
+ * print statements within this driver
+ */
+typedef void (*XDebug_Printf)(const char *fmt, ...);
+
+#if defined(DEBUG) && !defined(NDEBUG)
+
+//#ifndef XDEBUG_WARNING
+//#define XDEBUG_WARNING
+//#warning DEBUG is enabled
+//#endif
+
+int printf(const char *format, ...);
+
+#define XDBG_DEBUG_ERROR             0x00000001U    /* error  condition messages */
+#define XDBG_DEBUG_GENERAL           0x00000002U    /* general debug  messages */
+#define XDBG_DEBUG_ALL               0xFFFFFFFFU    /* all debugging data */
+
+#define xdbg_current_types (XDBG_DEBUG_GENERAL)
+
+#define xdbg_stmnt(x)  x
+
+#define xdbg_printf(type, ...) (((type) & xdbg_current_types) ? printf (__VA_ARGS__) : 0)
+
+
+#else /* defined(DEBUG) && !defined(NDEBUG) */
+
+#define xdbg_stmnt(x)
+
+#define xdbg_printf(...)
+
+#endif /* defined(DEBUG) && !defined(NDEBUG) */
+
+void XDebug_SetDebugBufPrintf(char *buff, int buff_size, int *buff_pos);
+void XDebug_SetDebugPrintf(XDebug_Printf PrintfFunc);
+
+extern XDebug_Printf xdebugPrintf;	/**< Instance of function
+						  *  interface used for debug
+						  *  print statement */
+/***************** Macros (Inline Functions) Definitions *********************/
+
+#define XDEBUG_PRINTF if (xdebugPrintf != NULL) xdebugPrintf
+
+
+#endif /* XDEBUG */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x.c
@@ -0,0 +1,1755 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x.c
+* @{
+*
+* This contains the implementation of the HDCP state machine module
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 2.00  als    09/30/15 Added EffectiveAddr argument to
+*                       XHdcp1x_CfgInitialize.
+* 2.10  MG     01/18/16 Added function XHdcp1x_IsEnabled.
+* 2.20  MG     01/20/16 Added function XHdcp1x_GetHdcpCallback.
+* 2.30  MG     02/25/16 Added function XHdcp1x_SetCallback and authenticated
+*                       callback.
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added functions:
+*                       XHdcp1x_DownstreamReady, XHdcp1x_GetRepeaterInfo,
+*                       XHdcp1x_SetCallBack, XHdcp1x_ReadDownstream
+* 4.0   yas    07/30/16 Addded function:
+*                       XHdcp1x_SetRepeater, XHdcp1x_IsInComputations,
+*                       XHdcp1x_IsInWaitforready, XHdcp1x_IsDwnstrmCapable,
+*                       XHdcp1x_GetTopology, XHdcp1x_DisableBlank,
+*                       XHdcp1x_EnableBlank, XHdcp1x_GetTopologyKSVList,
+*                       XHdcp1x_GetTopologyBKSV, XHdcp1x_SetTopologyField,
+*                       Hdcp1x_GetTopologyField, XHdcp1x_IsRepeater,
+*                       XHdcp1x_SetTopology, XHdcp1x_SetTopologyKSVList,
+*                       XHdcp1x_SetTopologyUpdate.
+* 4.0   yas    08/16/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XHdcp1x_CfgInitialize
+* 4.1   yas    11/10/16 Added function XHdcp1x_SetHdmiMode.
+* 4.1   yas    08/03/17 Updated the initialization to memset the XHdcp1x
+*                       structure to 0.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+#include "xhdcp1x_debug.h"
+#include "xhdcp1x_port.h"
+#include "xhdcp1x_rx.h"
+#include "xhdcp1x_tx.h"
+#include "xil_types.h"
+#include "xstatus.h"
+
+/************************** Constant Definitions *****************************/
+
+#if defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+    (XPAR_XV_HDMITX1_NUM_INSTANCES > 0)
+#define INCLUDE_TX
+#endif
+#if defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+    (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0)
+#define INCLUDE_RX
+#endif
+#if defined(XPAR_XV_HDMITX_NUM_INSTANCES) && (XPAR_XV_HDMITX_NUM_INSTANCES > 0)
+#define INCLUDE_TX
+#endif
+#if defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)
+#define INCLUDE_RX
+#endif
+#if defined(XPAR_XDP_NUM_INSTANCES) && (XPAR_XDP_NUM_INSTANCES > 0)
+#define INCLUDE_RX
+#define INCLUDE_TX
+#endif
+
+/**
+ * This defines the version of the software driver
+ */
+#define	DRIVER_VERSION			(0x00010023ul)
+
+/**************************** Type Definitions *******************************/
+
+/************************** Extern Declarations ******************************/
+
+/************************** Global Declarations ******************************/
+
+XHdcp1x_LogMsg XHdcp1xDebugLogMsg = NULL;	/**< Instance of function
+						  *  interface used for debug
+						  *  log message statement */
+XHdcp1x_KsvRevokeCheck XHdcp1xKsvRevokeCheck = NULL; /**< Instance of function
+						       *  interface used for
+						       *  checking a specific
+						       *  KSV against the
+						       *  platforms revocation
+						       *  list */
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function retrieves the configuration for this HDCP instance and fills
+* in the InstancePtr->Config structure.
+*
+* @param	InstancePtr is the device whose adaptor is to be determined.
+* @param	CfgPtr is the configuration of the instance.
+* @param	PhyIfPtr is pointer to the underlying physical interface.
+* @param	EffectiveAddr is the device base address in the virtual
+*		memory space. If the address translation is not used,
+*		then the physical address is passed.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CfgInitialize(XHdcp1x *InstancePtr, const XHdcp1x_Config *CfgPtr,
+		void *PhyIfPtr, UINTPTR EffectiveAddr)
+{
+	int Status;
+	u32 RegVal;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+	Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+	/* Setup the InstancePtr. */
+	(void)memset((void *)InstancePtr, 0, sizeof(XHdcp1x));
+
+	/* Initialize InstancePtr. */
+	InstancePtr->Config = *CfgPtr;
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+	InstancePtr->Port.PhyIfPtr = PhyIfPtr;
+
+	/* Update IsRx. */
+	RegVal = XHdcp1x_ReadReg(EffectiveAddr, XHDCP1X_CIPHER_REG_TYPE);
+	RegVal &= XHDCP1X_CIPHER_BITMASK_TYPE_DIRECTION;
+	InstancePtr->Config.IsRx = (RegVal ==
+		XHDCP1X_CIPHER_VALUE_TYPE_DIRECTION_RX) ? TRUE : FALSE;
+
+	/* Update IsHDMI. */
+	RegVal = XHdcp1x_ReadReg(EffectiveAddr, XHDCP1X_CIPHER_REG_TYPE);
+	RegVal &= XHDCP1X_CIPHER_BITMASK_TYPE_PROTOCOL;
+	InstancePtr->Config.IsHDMI = (RegVal ==
+		XHDCP1X_CIPHER_VALUE_TYPE_PROTOCOL_HDMI) ? TRUE : FALSE;
+
+	InstancePtr->Port.Adaptor = XHdcp1x_PortDetermineAdaptor(InstancePtr);
+
+	/* Ensure existence of an adaptor initialization function. */
+	if (!InstancePtr->Port.Adaptor || !InstancePtr->Port.Adaptor->Init) {
+		return (XST_NO_FEATURE);
+	}
+	/* Invoke adaptor initialization function. */
+	Status = (*(InstancePtr->Port.Adaptor->Init))(InstancePtr);
+	if (Status != XST_SUCCESS) {
+		return (Status);
+	}
+
+	/* Initialize the cipher core. */
+	XHdcp1x_CipherInit(InstancePtr);
+	/* Initialize the transmitter/receiver state machine. */
+	if (!InstancePtr->Config.IsRx) {
+		/* Set all handlers to stub values, let user configure this
+		 * data later. If any new callbacks are added to the HDCP
+		 * RX interface they should be initialized to null. */
+		InstancePtr->Tx.AuthenticatedCallback = NULL;
+		InstancePtr->Tx.IsAuthenticatedCallbackSet = (FALSE);
+
+		InstancePtr->Tx.DdcRead = NULL;
+		InstancePtr->Tx.IsDdcReadSet = (FALSE);
+
+		InstancePtr->Tx.DdcWrite = NULL;
+		InstancePtr->Tx.IsDdcWriteSet = (FALSE);
+
+		InstancePtr->Tx.RepeaterExchangeCallback = NULL;
+		InstancePtr->Tx.IsRepeaterExchangeCallbackSet = (FALSE);
+
+		InstancePtr->Tx.UnauthenticatedCallback = NULL;
+		InstancePtr->Tx.IsUnauthenticatedCallbackSet = (FALSE);
+
+		/* Initialize TX */
+		XHdcp1x_TxInit(InstancePtr);
+	}
+	else {
+		/* Set all the receiver handlers to stub value, let
+		 * user configure this data later. If any new callbacks
+		 * are added to the HDCP TX interface they should be
+		 * initialized to null. */
+		InstancePtr->Rx.DdcSetAddressCallback = NULL;
+		InstancePtr->Rx.IsDdcSetAddressCallbackSet = (FALSE);
+
+		InstancePtr->Rx.DdcSetDataCallback = NULL;
+		InstancePtr->Rx.IsDdcSetDataCallbackSet = (FALSE);
+
+		InstancePtr->Rx.DdcGetDataCallback = NULL;
+		InstancePtr->Rx.IsDdcGetDataCallbackSet = (FALSE);
+
+		InstancePtr->Rx.RepeaterDownstreamAuthCallback = NULL;
+		InstancePtr->Rx.IsRepeaterDownstreamAuthCallbackSet = (FALSE);
+
+		InstancePtr->Rx.AuthenticatedCallback = NULL;
+		InstancePtr->Rx.IsAuthenticatedCallbackSet = (FALSE);
+
+		InstancePtr->Rx.UnauthenticatedCallback = NULL;
+		InstancePtr->Rx.IsUnauthenticatedCallbackSet = (FALSE);
+
+		InstancePtr->Rx.TopologyUpdateCallback = NULL;
+		InstancePtr->Rx.IsTopologyUpdateCallbackSet = (FALSE);
+
+		InstancePtr->Rx.EncryptionUpdateCallback = NULL;
+		InstancePtr->Rx.IsEncryptionUpdateCallbackSet = (FALSE);
+
+		/* Initialize RX */
+		XHdcp1x_RxInit(InstancePtr);
+	}
+
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+
+	return (XST_SUCCESS);
+}
+
+void XHdcp1x_LateInit(XHdcp1x *InstancePtr)
+{
+	if (InstancePtr->Config.IsRx)
+		XHdcp1x_RxLoadBksvToBuf(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+* This function polls an HDCP interface.
+*
+* @param	InstancePtr is the interface to poll.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_Poll(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxPoll(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxPoll(InstancePtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function posts a DOWNSTREAMREADY event to an HDCP interface.
+*
+* @param 	InstancePtr is the interface to reset.
+*
+* @return
+*		- XST_SUCCESS if successful.
+* 		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_DownstreamReady(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		/* No downstreamready for TX */
+		Status = XST_FAILURE;
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxDownstreamReady(InstancePtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function copies the V'H0, V'H1, V'H2, V'H3, V'H4, KSVList and BInfo
+* values in the HDCP RX HDCP Instance for Repeater validation .
+*
+* @param	InstancePtr is the receiver instance.
+* @param	RepeaterInfoPtr is the Repeater information in the transmitter
+* 		instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+* 		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_GetRepeaterInfo(XHdcp1x *InstancePtr,
+		XHdcp1x_RepeaterExchange *RepeaterInfoPtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(RepeaterInfoPtr != NULL);
+
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxGetRepeaterInfo(InstancePtr,
+			RepeaterInfoPtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return Status;
+}
+
+
+/*****************************************************************************/
+/**
+* This function sets the Repeater functionality for an HDCP interface.
+*
+* @param	InstancePtr is the interface to disable.
+* @param	State is etiher TRUE or FALSE
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_SetRepeater(XHdcp1x *InstancePtr, u8 State)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	InstancePtr->IsRepeater = State;
+
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxSetRepeaterBcaps(InstancePtr,
+			State);
+	}
+#endif
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function resets an HDCP interface.
+*
+* @param 	InstancePtr is the interface to reset.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_Reset(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxReset(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxReset(InstancePtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function enables an HDCP interface.
+*
+* @param	InstancePtr is the interface to enable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_Enable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxEnable(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxEnable(InstancePtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables an HDCP interface.
+*
+* @param	InstancePtr is the interface to disable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_Disable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxDisable(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxDisable(InstancePtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function updates the state of the underlying physical interface.
+*
+* @param	InstancePtr is the interface to update.
+* @param	IsUp indicates the state of the underlying physical interface.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_SetPhysicalState(XHdcp1x *InstancePtr, int IsUp)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxSetPhysicalState(InstancePtr, IsUp);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxSetPhysicalState(InstancePtr, IsUp);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the lane count of a hdcp interface
+*
+* @param	InstancePtr is the interface to update.
+* @param	LaneCount is the lane count.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_SetLaneCount(XHdcp1x *InstancePtr, int LaneCount)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if ((!InstancePtr->Config.IsRx) && (!InstancePtr->Config.IsHDMI)) {
+		Status = XHdcp1x_TxSetLaneCount(InstancePtr, LaneCount);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if ((InstancePtr->Config.IsRx) && (!InstancePtr->Config.IsHDMI)) {
+		Status = XHdcp1x_RxSetLaneCount(InstancePtr, LaneCount);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initiates authentication of an HDCP interface.
+*
+* @param	InstancePtr is the interface to initiate authentication on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_Authenticate(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxAuthenticate(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxAuthenticate(InstancePtr);
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initiates downstream read of READY bit and consequently the
+* second part of Repeater authentication.
+*
+* @param	InstancePtr is the interface to initiate authentication on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_ReadDownstream(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxReadDownstream(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		/* Does nothing for Rx state machine.*/
+	}
+	else
+#endif
+	{
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to determine if authentication is in
+* progress.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	Truth value indicating authentication in progress (TRUE)
+*		or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsInProgress(const XHdcp1x *InstancePtr)
+{
+	int IsInProgress = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		IsInProgress = XHdcp1x_TxIsInProgress(InstancePtr);
+	}
+#endif
+
+	return (IsInProgress);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to determine if it has successfully
+* completed authentication.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	Truth value indicating authenticated (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsAuthenticated(const XHdcp1x *InstancePtr)
+{
+	int IsAuth = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		IsAuth = XHdcp1x_TxIsAuthenticated(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		IsAuth = XHdcp1x_RxIsAuthenticated(InstancePtr);
+	}
+	else
+#endif
+	{
+		IsAuth = FALSE;
+	}
+
+	return (IsAuth);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to determine if it is in the state of
+* computations or not.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	Truth value indicating authenticated (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsInComputations(const XHdcp1x *InstancePtr)
+{
+	int IsInComp = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		IsInComp = XHdcp1x_TxIsInComputations(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		IsInComp = XHdcp1x_RxIsInComputations(InstancePtr);
+	}
+	else
+#endif
+	{
+		IsInComp = FALSE;
+	}
+
+	return (IsInComp);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to determine if it is in the
+* wait-for-ready state or not.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	Truth value indicating authenticated (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsInWaitforready(const XHdcp1x *InstancePtr)
+{
+	int IsInWfr = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		IsInWfr = XHdcp1x_TxIsInWaitforready(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		IsInWfr = XHdcp1x_RxIsInWaitforready(InstancePtr);
+	}
+	else
+#endif
+	{
+		IsInWfr = FALSE;
+	}
+
+	return (IsInWfr);
+}
+
+/*****************************************************************************/
+/**
+* This function queries the device connected to the downstream interface to
+* determine if it supports hdcp or not.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	Truth value indicating HDCP capability (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsDwnstrmCapable(const XHdcp1x *InstancePtr)
+{
+	int IsCapable = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		IsCapable = XHdcp1x_TxIsDownstrmCapable(InstancePtr);
+	}
+#endif
+
+	return (IsCapable);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to determine if it is enabled.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	Truth value indicating enabled (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsEnabled(const XHdcp1x *InstancePtr)
+{
+	int IsEnabled = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		IsEnabled = XHdcp1x_TxIsEnabled(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		IsEnabled = XHdcp1x_RxIsEnabled(InstancePtr);
+	}
+	else
+#endif
+	{
+		IsEnabled = FALSE;
+	}
+
+	return (IsEnabled);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the current encryption map of the video streams
+* traversing an hdcp interface.
+*
+* @param 	InstancePtr is the interface to query.
+*
+* @return	The current encryption map.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_GetEncryption(const XHdcp1x *InstancePtr)
+{
+	u64 StreamMap = 0;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		StreamMap = XHdcp1x_TxGetEncryption(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		StreamMap = XHdcp1x_RxGetEncryption(InstancePtr);
+	}
+	else
+#endif
+	{
+		StreamMap = 0;
+	}
+
+	return (StreamMap);
+}
+
+/*****************************************************************************/
+/**
+* This function determines if the video stream is encrypted.
+* The traffic is encrypted if the encryption bit map is non-zero and the
+* interface is authenticated.
+*
+* @param	InstancePtr is a pointer to the HDCP instance.
+*
+* @return	Truth value indicating encrypted (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsEncrypted(const XHdcp1x *InstancePtr)
+{
+	return (XHdcp1x_GetEncryption(InstancePtr) &&
+		XHdcp1x_IsAuthenticated(InstancePtr));
+}
+
+/*****************************************************************************/
+/**
+* This function enables encryption on a series of streams within an HDCP
+* interface.
+*
+* @param	InstancePtr is the interface to configure.
+* @param	Map is the stream map to enable encryption on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_EnableEncryption(XHdcp1x *InstancePtr, u64 Map)
+{
+	int Status = XST_FAILURE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxEnableEncryption(InstancePtr, Map);
+	}
+#else
+	UNUSED(Map);
+#endif
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables encryption on a series of streams within an HDCP
+* interface.
+*
+* @param	InstancePtr is the interface to configure.
+* @param	Map is the stream map to disable encryption on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_DisableEncryption(XHdcp1x *InstancePtr, u64 Map)
+{
+	int Status = XST_FAILURE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxDisableEncryption(InstancePtr, Map);
+	}
+#else
+	UNUSED(Map);
+#endif
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the key selection vector that is to be used by the HDCP
+* cipher.
+*
+* @param	InstancePtr is the interface to configure.
+* @param	KeySelect is the key selection vector.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_SetKeySelect(XHdcp1x *InstancePtr, u8 KeySelect)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	Status = XHdcp1x_CipherSetKeySelect(InstancePtr, KeySelect);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function handles a timeout on an HDCP interface.
+*
+* @param	InstancePtr is the interface.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_HandleTimeout(void *InstancePtr)
+{
+	XHdcp1x *HdcpPtr = InstancePtr;
+
+	/* Verify argument. */
+	Xil_AssertVoid(HdcpPtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!HdcpPtr->Config.IsRx) {
+		XHdcp1x_TxHandleTimeout(HdcpPtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	if (HdcpPtr->Config.IsRx) {
+		XHdcp1x_RxHandleTimeout(HdcpPtr);
+	}
+	else
+#endif
+	{
+		XDEBUG_PRINTF("unknown interface type\r\n");
+	}
+}
+
+#if 0
+void XHdcp1x_DebugBufPrintf(const char *fmt, ...)
+{
+	if(XHdcp1xDebugBuff != NULL)
+	{
+		va_list args;
+		va_start(args, fmt);
+		*XHdcp1xDebugBuffPos += vscnprintf(XHdcp1xDebugBuff + *XHdcp1xDebugBuffPos,
+				XHdcp1xDebugBuffSize - *XHdcp1xDebugBuffPos, fmt, args);
+		va_end(args);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the debug printf function for the module to print to the
+* supplied buffer.
+*
+* @param	buff is the buffer to print to.
+* @param	buff_size is the maximum size of the buffer
+* @param	buff_pos is the current (and will be updated) position in the buffer
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_SetDebugBufPrintf(char *buff, int buff_size, int *buff_pos)
+{
+	if(buff)
+	{
+		XHdcp1xDebugBuff = buff;
+		XHdcp1xDebugBuffSize = buff_size;
+		XHdcp1xDebugBuffPos = buff_pos;
+		XHdcp1x_SetDebugPrintf(XHdcp1x_DebugBufPrintf);
+	} else {
+		XHdcp1x_SetDebugPrintf(NULL);
+		XHdcp1xDebugBuff = NULL;
+		XHdcp1xDebugBuffSize = 0;
+		XHdcp1xDebugBuffPos = NULL;
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function sets the debug log message function for the module.
+*
+* @param	LogFunc is the debug logging function.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_SetDebugLogMsg(XHdcp1x_LogMsg LogFunc)
+{
+	XHdcp1xDebugLogMsg = LogFunc;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the KSV revocation list check function for the module.
+*
+* @param	RevokeCheckFunc is the KSV revocation list check function.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_SetKsvRevokeCheck(XHdcp1x_KsvRevokeCheck RevokeCheckFunc)
+{
+	XHdcp1xKsvRevokeCheck = RevokeCheckFunc;
+}
+
+/*****************************************************************************/
+/**
+* This function sets timer start function for the module.
+*
+* @param	InstancePtr is the pointer to the HDCP interface.
+* @param	TimerStartFunc is the timer start function.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_SetTimerStart(XHdcp1x *InstancePtr, XHdcp1x_TimerStart TimerStartFunc)
+{
+	/* Verify Argument */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->XHdcp1xTimerStart = TimerStartFunc;
+}
+
+/*****************************************************************************/
+/**
+* This function sets timer stop function for the module.
+*
+* @param	InstancePtr is the pointer to the HDCP interface.
+* @param	TimerStopFunc is the timer stop function.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_SetTimerStop(XHdcp1x *InstancePtr, XHdcp1x_TimerStop TimerStopFunc)
+{
+	/* Verify Argument */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->XHdcp1xTimerStop = TimerStopFunc;
+}
+
+/*****************************************************************************/
+/**
+* This function sets timer busy delay function for the module.
+*
+* @param	InstancePtr is the pointer to the HDCP interface.
+* @param	TimerDelayFunc is the timer busy delay function.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_SetTimerDelay(XHdcp1x *InstancePtr, XHdcp1x_TimerDelay TimerDelayFunc)
+{
+	/* Verify Argument */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->XHdcp1xTimerDelay = TimerDelayFunc;
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the version of the HDCP driver software.
+*
+* @return	The software driver version.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdcp1x_GetDriverVersion(void)
+{
+	return (DRIVER_VERSION);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the cipher version of an HDCP interface.
+*
+* @param	InstancePtr is the interface to query.
+*
+* @return	The cipher version used by the interface
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdcp1x_GetVersion(const XHdcp1x *InstancePtr)
+{
+	u32 Version = 0;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	Version = XHdcp1x_CipherGetVersion(InstancePtr);
+
+	return (Version);
+}
+
+/*****************************************************************************/
+/**
+* This function performs a debug display of an HDCP instance.
+*
+* @param	InstancePtr is the interface to display.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_Info(const XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		XHdcp1x_TxInfo(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		XHdcp1x_RxInfo(InstancePtr);
+	}
+	else
+#endif
+	{
+		XDEBUG_PRINTF("unknown interface type\r\n");
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function processes the AKsv.
+*
+* @param	InstancePtr is the interface to display.
+*
+* @return	None
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_ProcessAKsv(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		InstancePtr->Port.Adaptor->CallbackHandler(InstancePtr);
+	}
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pointer to the downstream Topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return   A pointer to the XHdcp14 Topology structure or NULL when
+*           the topology info is invalid.
+*
+* @note     None.
+*
+******************************************************************************/
+void *XHdcp1x_GetTopology(XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	void *TopologyPtr = NULL;
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		TopologyPtr = XHdcp1x_TxGetTopology(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		/* Not currently applicable */
+	}
+	else
+#endif
+	{
+		XDEBUG_PRINTF("unknown interface type\r\n");
+	}
+
+	return TopologyPtr;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the blank output for the cipher.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdcp1x_DisableBlank(XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		XHdcp1x_TxDisableBlank(InstancePtr);
+	}
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the blank output for the cipher.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdcp1x_EnableBlank(XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		XHdcp1x_TxEnableBlank(InstancePtr);
+	}
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the value of KSV List read in the downstream interface
+* of the repeater topology.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - List of KSVs of the downstream devices
+*
+* @note     None.
+*
+******************************************************************************/
+u8 *XHdcp1x_GetTopologyKSVList(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u8 *KSVList = NULL;
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		KSVList = XHdcp1x_TxGetTopologyKSVList(InstancePtr);
+	}
+#endif
+
+	return (KSVList);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the value of KSV of the device attached to the
+* downstream interface of the repeater.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - TRUE if MAX_DEPTH_EXCEEDED
+*
+* @note     None.
+*
+******************************************************************************/
+u8 *XHdcp1x_GetTopologyBKSV(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u8 *BKSV = NULL;
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		BKSV = XHdcp1x_TxGetTopologyBKSV(InstancePtr);
+	}
+#endif
+
+	return (BKSV);
+}
+
+/*****************************************************************************/
+/**
+* This function is used to set various fields inside the topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp1x core instance.
+* @param    Field indicates what field of the topology structure to update.
+* @param    Value is the value assigned to the field of the topology structure.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_SetTopologyField(XHdcp1x *InstancePtr,
+		XHdcp1x_TopologyField Field, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Field < XHDCP1X_TOPOLOGY_INVALID);
+
+	switch(Field)
+	{
+	case XHDCP1X_TOPOLOGY_DEPTH :
+		XHdcp1x_RxSetTopologyDepth(InstancePtr, Value);
+		break;
+	case XHDCP1X_TOPOLOGY_DEVICECNT :
+		XHdcp1x_RxSetTopologyDeviceCnt(InstancePtr, Value);
+		break;
+	case XHDCP1X_TOPOLOGY_MAXDEVSEXCEEDED :
+		XHdcp1x_RxSetTopologyMaxDevsExceeded(InstancePtr, Value);
+		break;
+	case XHDCP1X_TOPOLOGY_MAXCASCADEEXCEEDED :
+		XHdcp1x_RxSetTopologyMaxCascadeExceeded(InstancePtr, Value);
+		break;
+	case XHDCP1X_TOPOLOGY_HDCP20REPEATERDOWNSTREAM :
+		/* Not currently applicable */
+		break;
+	case XHDCP1X_TOPOLOGY_HDCP1DEVICEDOWNSTREAM :
+		/* Not currently applicable */
+		break;
+	case XHDCP1X_TOPOLOGY_INVALID :
+		/* Not currently applicable */
+		break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is used to get various fields inside the topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp1x core instance.
+* @param    Field indicates what field of the topology structure to update.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+u32 XHdcp1x_GetTopologyField(XHdcp1x *InstancePtr, XHdcp1x_TopologyField Field)
+{
+	u32 Value = 0;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Field < XHDCP1X_TOPOLOGY_INVALID);
+
+	switch(Field)
+	{
+	case XHDCP1X_TOPOLOGY_DEPTH :
+		Value = XHdcp1x_TxGetTopologyDepth(InstancePtr);
+		break;
+	case XHDCP1X_TOPOLOGY_DEVICECNT :
+		Value = XHdcp1x_TxGetTopologyDeviceCnt(InstancePtr);
+		break;
+	case XHDCP1X_TOPOLOGY_MAXDEVSEXCEEDED :
+		Value = XHdcp1x_TxGetTopologyMaxDevsExceeded(InstancePtr);
+		break;
+	case XHDCP1X_TOPOLOGY_MAXCASCADEEXCEEDED :
+		Value = XHdcp1x_TxGetTopologyMaxCascadeExceeded(InstancePtr);
+		break;
+	case XHDCP1X_TOPOLOGY_HDCP20REPEATERDOWNSTREAM :
+		/* Not currently applicable */
+		break;
+	case XHDCP1X_TOPOLOGY_HDCP1DEVICEDOWNSTREAM :
+		/* Not currently applicable */
+		break;
+	case XHDCP1X_TOPOLOGY_INVALID :
+		/* Not currently applicable */
+		break;
+	}
+
+	return Value;
+}
+
+/*****************************************************************************/
+/**
+* This function return if the HDCP interface is a repeater in case of Rx or
+* is connected to a repeater in case of Tx
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- TRUE if Repeater.
+*		- FALSE if not Repeater,
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_IsRepeater(XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u8 Status = FALSE;
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxIsRepeater(InstancePtr);
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		Status = (InstancePtr->IsRepeater)? TRUE : FALSE;
+	}
+	else
+#endif
+	{
+		XDEBUG_PRINTF("unknown interface type\r\n");
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the RepeaterInfo value int the HDCP RX instance
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    TopologyPtr is a pointer to the Repeater Info value(s).
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_SetTopology(XHdcp1x *InstancePtr,
+		const XHdcp1x_RepeaterExchange *TopologyPtr)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TopologyPtr != NULL);
+
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		 XHdcp1x_RxSetTopology(InstancePtr, TopologyPtr);
+	}
+	else
+#endif
+	{
+		TopologyPtr = NULL;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the KSVList value(s) in the HDCP RX KSV Fifo register
+* space for the upstream interface to read.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    ListPtr is a pointer to the KSV list.
+* @param    ListSize is the number of KSVs in the list.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_SetTopologyKSVList(XHdcp1x *InstancePtr, u8 *ListPtr,
+		u32 ListSize)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(ListPtr != NULL);
+
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		XHdcp1x_RxSetTopologyKSVList(InstancePtr, ListPtr,	ListSize);
+	}
+	else
+#else
+	UNUSED(ListSize);
+#endif
+	{
+		ListPtr = NULL;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function does the necessary actions to update HDCP
+* after the topology has been set.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_SetTopologyUpdate(XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		/* Not currently applicable */
+	}
+	else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		XHdcp1x_RxSetTopologyUpdate(InstancePtr);
+	}
+	else
+#endif
+	{
+		XDEBUG_PRINTF("unknown interface type\r\n");
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function set the HDMI_MODE in the BStatus register of the HDMI DDC
+* space.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param	Value is the truth-value.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_SetHdmiMode(XHdcp1x *InstancePtr, u8 Value)
+{
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if defined(INCLUDE_TX)
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		XHdcp1x_TxSetHdmiMode(InstancePtr, Value);
+	} else
+#endif
+#if defined(INCLUDE_RX)
+	/* Check for RX */
+	if (InstancePtr->Config.IsRx) {
+		XHdcp1x_RxSetHdmiMode(InstancePtr, Value);
+	} else
+#endif
+	{
+		XDEBUG_PRINTF("unknown interface type\r\n");
+	}
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x.h
@@ -0,0 +1,1248 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x.h
+* @{
+* @details
+*
+* This is the Xilinx HDCP device drivers. The Xilinx HDCP driver software is
+* provided to allow for the integration of HDCP functionality into designs
+* that make use of the DisplayPort and HDMI LogiCORE IP video interface
+* cores. This software is distributed within the Xilinx SDK (Software
+* Development Kit) and is tightly coupled with the SDK drivers for these
+* interfaces. This appendix serves as a technical reference describing the
+* architecture and functionality of HDCP driver software as well as providing
+* guidelines for integrating it into a custom DisplayPort and/or HDMI system
+* designs based on Xilinx programmable devices.
+*
+* <b> Platform Requirements </b>
+* The current platform requirements for the HDCP driver software are as
+* follows:
+* - One or more of the following video interfaces (subject to any and all
+*   identified Restrictions and Limitations):
+*    - DisplayPort receive
+*    - DisplayPort transmit
+*    - HDMI receive
+*    - HDMI transmit
+* - One HDCP 1.x cipher LogiCORE IP instance per video interface that
+*   supports HDCP 1.x.
+* - One HDCP device key set per video interface that supports HDCP 1.x and
+*   the associated RTL/IP to interface these to the HDCP 1.x ciphers.
+* - One timer resource per HDCP 1.x transmit interface that can support
+*   durations from a few milliseconds up to several seconds in length.
+* - Approximately 128 KB of free code space (HDCP specifics only)
+* - Approximately 1 KB of free data space per HDCP interface (HDCP specifics
+*   only).
+*
+* <b> Restrictions and Limitations </b>
+* The HDCP driver software has the following restrictions and limitations:
+* - DisplayPort receiver and HDMI receiver interfaces are not supported
+*   within the same platform design.
+* - DisplayPort transmitter and HDMI transmitter interfaces are not supported
+*   within the same platform design.
+*
+* -- -- -- -- -- -- -- -- -- -- -- -- --
+*
+* <b> HDCP Driver Architecture </b>
+*
+* The architecture of the HDCP software driver can be divided into three
+* distinct submodules.
+* - Cipher device
+* - Port device
+* - Authentication state machine(s)
+* Each of these modules represents a specific function and/or entity within
+* the driver and work in unison to implement the HDCP software support within
+* the system design. The design of the driver encapsulates all of these
+* submodules into a unified API that is used by the client software
+* application with a single instance of an HDCP interface.
+*
+* <b> Cipher Device </b>
+*
+* The cipher device is contained within the HDCP driver software and represents
+* an instance of the HDCP cipher LogiCORE IP block within a system design.
+* Given that the variants of this cipher core provide the same interface to the
+* software, a single implementation of this submodule is used to drive all of
+* them. In the few places where behaviors differ slightly between variants,
+* this software adjusts at runtime based on the contents of a Type/ID
+* register within the IP core.
+*
+* The principal function of the cipher device submodule is to initialize,
+* configure, and monitor the physical encryption cipher used within the HDCP
+* application. As part of this, it provides an interface that allows the
+* software to trigger the reading of the appropriate device key set
+* from the custom key management solution that is attached to the cipher core.
+*
+* The cipher device submodule is used by higher-level authentication state
+* machines to run re-authentication requests, generate pseudo-random numbers,
+* and enable/disable encryption on individual video streams passing through
+* the cipher core.
+*
+* It also provides a status output from the actual encryption process that can
+* be used by the authentication state machines to monitor the correct operation
+* of the HDCP function.
+*
+* The interrupts generated by the cipher core are fully consumed within the
+* HDCP software driver; the client software application needs only to register
+* the cipher core interrupt with the associated vector within the appropriate
+* interrupt controller of the system design. These interrupts are forwarded to
+* the cipher submodule through an appropriate external API of the software
+* driver (XHdcp1x_CipherIntrHandler).
+*
+* The software driver source files that are associated with this submodule are
+* as follows:
+* - xhdcp1x_cipher.c
+* - xhdcp1x_cipher.h
+* - xhdcp1x_cipher_intr.c
+* - xhdcp1x_hw.h
+*
+* <b> Port Device </b>
+*
+* The port device(s) that exists within the HDCP software driver represent the
+* management and access to the HDCP register sets that are defined within the
+* HDCP specifications. While the register sets are similar between HDMI and
+* DisplayPort, they do differ, and as a result there are slightly different
+* implementations of these port devices between the two. Regardless of the
+* physical interface type, the transmit port device is always the master of the
+* register set transactions and the receive port device is always the slave.
+*
+* For transmit port devices, they provide the ability to read and write the
+* HDCP register set that exists on their attached receive (slave) device.
+* These transactions are always run to completion and are initiated solely by
+* the corresponding transmit state machine and/or as part of a debug process
+* if explicitly requested.
+*
+* For receive port devices, they only provide access to the local HDCP register
+* set; they cannot be used to read the register set from the attached transmit
+* device. Local reads and writes of this register set are performed by the
+* appropriate receive state machine (or debug process) and remote reads and
+* writes can be performed by the transmit port (master) device.
+*
+* Remote access (either read or write) to a subset of the register set
+* generates notifications (for example, interrupts) to the device that are then
+* in turn posted to the corresponding receive state machine for driving
+* authentication and related procedures. The underlying implementation of the
+* supported HDCP port device modules is completely dependent on the Xilinx BSP
+* device driver for the corresponding video interface type. As a result, the
+* client application software is required to provide the device handle of the
+* video interface that the specific HDCP driver instance is bound to during
+* initialization of the HDCP software driver.
+*
+* For more information on the BSP Standalone driver, see the following
+* documents:
+* - Xilinx Software Developer Kit Help (UG782)
+* - OS and Libraries Document Collection (UG643)
+*
+* The internals of the port device rely on the use of an adapter structure
+* (a jump table) which maps the HDCP port device API into a protocol
+* (DisplayPort/HDMI) and direction (RX/TX) specific function that implements
+* the associated functionality.
+* This adapter structure (XHdcp1x_PortPhyIfAdaptor) allows for the correct
+* function to be determined and called at run-time based on the exact type of
+* the HDCP interface in question. In some instances (specifically DisplayPort
+* TX), there is no specific port device interrupt defined and, as such, the
+* relevant interrupt(s) (HPD) must be forwarded to the port device submodule
+* through an appropriate external API of the software driver
+* (XHdcp1x_PortIntrHandler).
+*
+* The software driver source files that are associated with this submodule
+* are as follows:
+* - xhdcp1x_port.c
+* - xhdcp1x_port.h
+* - xhdcp1x_port_dp.h
+* - xhdcp1x_port_dp_rx.c
+* - xhdcp1x_port_dp_tx.c
+* - xhdcp1x_port_hdmi.h
+* - xhdcp1x_port_hdmi_rx.c
+* - xhdcp1x_port_hdmi_tx.c
+* - xhdcp1x_port_intr.c
+*
+* <b> Authentication State Machines </b>
+*
+* The transmit and receive authentication state machines contained within the
+* driver software mirror those that are defined within the appropriate HDCP
+* specifications. To facilitate integration and debugging, the names of the
+* individual states are aligned with those defined within the specifications
+* wherever possible.
+*
+* The state machines are responsible for driving the authentication,
+* encryption, and link monitoring processes as requested by the client
+* application software.
+*
+* The state machines co-ordinate the operation of the cipher, port device(s),
+* and the physical video interface (HDMI or DisplayPort), and rely upon the
+* proper programming and availability of HDCP device keys.
+*
+* The state machines make use of a simple, OS-independent scheduler to allow
+* for messages and requests to be posted to and from them. This requires the
+* client application software to regularly call a poll function on each HDCP
+* interface to ensure the timely servicing of these messages/requests.
+*
+* The transmit state machine provides interfaces that allow for the client
+* application software to request authentication, enable/disable the encryption
+* of video streams, and monitor the progress/outcome of authentication and the
+* ongoing integrity of the encrypted video data. The transmit state must be
+* notified of changes in the physical state of the interface it is running over
+* (either HDMI or DisplayPort) to ensure that any required re-authentication is
+* performed without explicit intervention of the client software application.
+* It fully supports downstream HDCP receivers and repeaters. For a detailed
+* diagram of this state machine, see either figure 2-6 in the High-bandwidth
+* Digital Content Protection System v1.3 Amendment for DisplayPort
+* specification or figure 2-9 in the High-bandwidth Digital Content
+* Protection System v1.4 specification. The transmit state definitions are
+* contained within the XHdcp1x_StateType contained within the
+* xhdcp1x_tx.c source file.
+*
+* The receive state machine is much simpler than the transmit in that it is
+* not entirely aware of the success/failure of the authentication process.
+* It merely initiates the calculations required for authentication and makes
+* the result available within its HDCP register set for examination by the
+* transmitter. It allows for the client application software to explicitly
+* enable/disable the HDCP capability of the underlying video interface and to
+* query whether encrypted video is being received at any point in time. It
+* also requires that it be notified of changes in the physical interface it is
+* running over so that the appropriate side effects can be initiated. For a
+* detailed diagram of this state machine, see either figure 2-7 in the the
+* High-bandwidth Digital Content Protection System v1.3 Amendment for
+* DisplayPort specification or figure 2-10 in the High-bandwidth Digital
+* Content Protection System v1.4 specification. The receive state definitions
+* are contained within the XHdcp1x_StateType contained within the
+* xhdcp1x_rx.c source file.
+*
+* Both the transmit and receive state machines make use of a link verification
+* procedure to ensure that both ends of the encrypted link remain synchronized
+* over time. This mechanism differs between DisplayPort and HDMI and is
+* detailed in section 2.2.4 of the High-bandwidth Digital Content Protection
+* System v1.3 Amendment for DisplayPort specification [Ref 1] and section 2.2.3
+* of the High-bandwidth Digital Content Protection System v1.4 specification
+* respectively.
+*
+* The software driver source files that are associated with this submodule are
+* as follows:
+* - xhdcp1x.c
+* - xhdcp1x.h
+* - xhdcp1x_intr.c
+* - xhdcp1x_platform.c
+* - xhdcp1x_platform.h
+* - xhdcp1x_rx.c
+* - xhdcp1x_rx.h
+* - xhdcp1x_selftest.c
+* - xhdcp1x_sinit.c
+* - xhdcp1x_tx.c
+* - xhdcp1x_tx.h
+*
+* <b> Device Key Management </b>
+*
+* The device key management software and RTL/IP implementation interact with
+* the HDCP software driver but are, in the strictest sense, outside of the
+* scope of this driver. The Xilinx HDCP solution is designed such that each
+* individual platform integrator is responsible for the security and storage of
+* the HDCP device keys that are issued to them by DCP LLC. The physical
+* interface between the LogiCORE IP HDCP Cipher Product Guide and the custom
+* implemented key storage is described in the High-bandwidth Digital Content
+* Protection System v1.3 Amendment for DisplayPort specification and the
+* High-bandwidth Digital Content Protection System v1.4 specification.
+*
+* <b> Dependencies </b>
+*
+* The only dependencies between the HDCP driver software and the actual device
+* key management implementation are, as follows:
+*   - The device keys must be available to be loaded into the HDCP cipher
+*   LogiCORE IP prior to initializing the corresponding instance of the
+*   HDCP software driver.
+*   - The HDCP software driver supports the programming of key set selection
+*   vector. This can be used in applications where multiple sets of device keys
+*   are available for use. This vector allows for one of up to eight different
+*   device key sets to be selected as the data to be loaded when requested by
+*   the cipher core. The API function used to set this selection vector
+*   is XHdcp1x_SetKeySelect.
+*
+* -- -- -- -- -- -- -- -- -- -- -- -- --
+*
+* <b> HDCP Driver Porting Guide </b>
+*
+* The following system resources are required by the HDCP software driver
+* software:
+* - Approximately 128 KB of free code space
+* - Approximately 1 KB of free data space per HDCP driver instance
+* - Approximately 1 KB of stack space
+* - One dedicated operating system thread/task for HDCP (if an operating
+*   system is being used)
+* Note: These resource requirements are those needed explicitly for HDCP. The
+* requirements associated with the mandatory video interface(s), HDMI or
+* DisplayPort (DP) are not included.
+*
+* <b> Integrating Into Your Application </b>
+*
+* The HDCP software driver can be integrated into any client software
+* application, regardless of whether an operating system is used or not. This
+* integration generally consists of a few simple steps.
+*
+* 1. Allocation of the required number of HDCP driver instances.
+*
+* 2. Binding of the system timer interface functions (only needed if HDCP
+*    transmit interfaces are to be used). These functions are used by the state
+*    machines to run guard timers where appropriate within the authentication
+*    procedure. These functions are, as follows:
+*        - XHdcp1x_SetTimerStart
+*        - XHdcp1x_SetTimerStop
+*        - XHdcp1x_SetTimerDelay
+*
+* 3. Binding of the platform-specific timer expiry handling to call
+*    XHdcp1x_HandleTimeout when a timer started using the interfaces in step
+*    2 expires.
+*
+* 4. Optional binding of the platform specific function that tests KSV against
+*    a stored revocation list (HDCP transmit interfaces only) using
+*    XHdcp1x_SetKsvRevokeCheck.
+*
+* 5. Initialization, self-test, and basic configuration of the HDCP driver
+*    instances. The relevant functions are:
+*        - XHdcp1x_CfgInitialize
+*        - XHdcp1x_LookupConfig
+*        - XHdcp1x_SelfTest
+*        - XHdcp1x_SetKeySelect
+*
+* 6. Binding of the HDCP cipher core interrupt lines and callback functions
+*    with the platform interrupt controller(s). The relevant function is
+*    XHdcp1x_CipherIntrHandler.
+*
+* 7. Registration of the HDCP 1.x port interrupt handler with the corresponding
+*    HDMI or DisplayPort device driver. The relevant function is
+*    XHdcp1x_PortIntrHandler.
+*        - DisplayPort RX: not used
+*        - DisplayPort TX: insert into the HPD event and interrupt callback
+*          functions
+*        - HDMI RX/TX: not used
+*
+* 8. Insertion of calls to HDCP set physical state and lane count function(s)
+*    in the appropriate physical interface driver callback functions (HDMI or
+*    DisplayPort). The functions of interest are:
+*        - XHdcp1x_SetPhysicalState
+*             - DisplayPort RX: insert into the driver callbacks that handle
+*               training done (up), training lost (down), bandwidth change
+*               (down), and cable unplug (down)
+*             - DisplayPort TX: insert in the function that starts/trains the
+*               DisplayPort link (up or down based on the outcome)
+*             - HDMI RX/TX: call in the stream up/down callback functions
+*        - XHdcp1x_SetLaneCount
+*             - DisplayPort RX: insert into the training done driver callback
+*             - DisplayPort TX: insert in the function that starts/trains the
+*               DisplayPort link
+*             - HDMI RX/TX: not used
+*
+* 9. Insertion of a call to poll each of the HDCP driver instances within
+*    either the main loop of the client software application (bare-metal) or
+*    within an HDCP specific thread (operating system). The relevant function
+*    within the driver software is XHdcp1x_Poll.
+*
+* 10. Insertion of calls where appropriate within the client specific
+*     application software to administratively manage and monitor the operation
+*     of the HDCP driver instances.
+*        - XHdcp1x_Authenticate (transmit interfaces only)
+*        - XHdcp1x_Disable
+*        - XHdcp1x_DisableEncryption (transmit interfaces only)
+*        - XHdcp1x_Enable
+*        - XHdcp1x_EnableEncryption (transmit interfaces only)
+*        - XHdcp1x_GetEncryption
+*        - XHdcp1x_IsAuthenticated
+*        - XHdcp1x_IsInProgress
+*
+* It is important to note that the physical video interfaces over which HDCP
+* is to be run must physically exist and be initialized prior to the
+* initialization of the corresponding HDCP driver instance. If this is not the
+* case, then the HDCP driver software will not work as designed. In addition,
+* interrupts on the physical interface should not be enabled until after the
+* corresponding HDCP driver instance has been initialized. While the successful
+* operation of this driver relies on the use interrupts, there are no external
+* interrupt callbacks to be registered specifically by the client software
+* using the HDCP software driver. All of the HDCP-specific interrupts are fully
+* consumed within the software driver and all the client software needs to do
+* is properly complete integration using step 6, step 7, and step 8.
+*
+* IMPORTANT: Virtually all of the exported API functions that do not query the
+* state of the driver require a subsequent call to the poll function in order
+* for the request to be fully serviced by the indicated driver instance. As a
+* result, it is crucial that the interface be polled in a timely fashion
+* subsequent to such an API call.
+*
+* <b> Debugging </b>
+*
+* The HDCP software driver software provides two different mechanisms for
+* facilitating the integration and debug into client application software.
+* These are:
+* - Runtime debug logging information
+* - On demand detailed status display
+*
+* To enable the runtime debug logging of the driver software, the client
+* application can register a printf-style debug logging function with the
+* driver using the appropriate API.
+*
+* If this is done, then the authentication state machines log all state
+* transitions and periodic status information, providing significant insight
+* into their operation. The function that can be used to register this logging
+* function is XHdcp1x_SetDebugLogMsg.
+*
+* Note: This debug logging is enabled/disabled on the driver as a whole (as
+* opposed to on a single interface at a time) and does not support priorities
+* of any kind.
+*
+* In addition to runtime logging, the client application can register a
+* printf-style debug print function with the driver software.
+* This registration permits the driver to perform a one-time dump of detailed
+* status information related to a specific HDCP driver instance when triggered
+* by the client application software. The relevant functions for this are:
+* - XHdcp1x_SetDebugPrintf
+* - XHdcp1x_Info
+*
+* The information displayed using the XHdcp1x_Info function includes details
+* on the current/previous state, encryption status, driver/core version(s),
+* as well as statistics detailing the operation of the authentication state
+* machine (RX and TX) and as its corresponding cipher and port sub-modules.
+* The format of the information displayed differs slightly based on whether
+* the HDCP interface is in the receive or transmit direction
+*
+* -- -- -- -- -- -- -- -- -- -- -- -- --
+*
+* <b> Receive Authentication </b>
+*
+* The CE register accesses associated with the receiver authentication should
+* be as follows:
+* - Write of the Control register to enable the core, enable immediate register
+*   updates and set the number of lanes to be used.
+* - Write the Cipher Control register to set Bit[0] (the XOR function is to be
+*   enabled on the receiver for authentication).
+* - Write of the Key Management Block Control register to load local KSV. Set
+*   and then immediately clear Bit[0].
+* - Read of Key Management Block Status register and check Bit[0] to confirm
+*   local KSV available (poll as required).
+* - Read of the Local KSV (H) and Local KSV (L) registers.
+* - Write of the Remote KSV (H) and Remote KSV (L) registers with the KSV
+*   value sent by the TX.
+* - Write of the Key Management Block Control register to trigger the
+*   calculation of Km. Set and then immediately clear Bit[1]. Set Key
+*   Management Block control register to abort Km calculation, and then
+*   immediately clear Bit[2].
+* - Read of the Key Management Status register and check Bit[1] to confirm Km
+*   available (poll as required).
+* - Write of Cipher Bx, By, and Bz registers (with An).
+* - Read the calculated value of Km and write of Cipher Kx, Ky, and Kz
+*   registers (with Km) if needed by the Cipher version.
+* - Write to Cipher Control register to initiate block cipher. Clear Bit[16]
+*   to ensure that the calculated Km value is used. Set and then immediately
+*   clear Bit[8].
+* - Read of Cipher Status register and check Bit[8] to confirm block cipher
+*   complete (poll as required).
+* - Read of Cipher Ri register.
+*
+* Note: Any step that requires the writing of multiple registers are
+* "book ended" with the clearing and subsequent setting of the register update
+* bit within the Control register.
+*
+* -- -- -- -- -- -- -- -- -- -- -- -- --
+*
+* <b> Transmit Authentication </b>
+*
+* The CE register accesses associated with the transmitter authentication
+* should be as follows:
+* - Write of the Control register to enable the core, enable immediate register
+*   updates and set the number of lanes to be used.
+* - Write the Cipher Control register to clear Bit[0] (the XOR function is to
+*   be disabled on the transmitter for authentication).
+* - Write of the Cipher Control register to generate random number. Bit[10]
+*   should be set and immediately cleared.
+* - Read of Cipher Status register and check Bit[10] to confirm RNG complete
+*   (poll as required).
+* - Read of the Cipher Mi (H) and Cipher Mi (L) registers (this value is An).
+* - Write of the Key Management Control register to load local KSV. Set and
+*   then immediately clear Bit[0].
+* - Read of Key Management Status register and check Bit[0] to confirm local
+*   KSV available (poll as required).
+* - Read of the Local KSV (H) and Local KSV (L) registers.
+* - Write of the Remote KSV (H) and Remote KSV (L) registers with the value
+*   read from the RX.
+* - Write of the Key Management Control register to calculate Km. Set and
+*   immediately clear Bit[1]. Set Key Management Block control register to
+*   abort Km calculation, and then immediately clear Bit[2]
+* - Read of the Key Management Status register and check Bit[1] to confirm Km
+*   available (poll as required).
+* - Write of Cipher Bx, By, and Bz registers (with An + repeater bit).
+* - Read the calculated value of Km and write of Cipher Kx, Ky, and Kz
+*   registers (with Km) if needed by the Cipher version.
+* - Write to Cipher Control register to initiate block Cipher. Clear Bit[16]
+*   to ensure that the calculated Km value is used. Set and then immediately
+*   clear Bit[8].
+* - Read of Cipher Status register and check Bit[8] to confirm block cipher
+*   complete (poll as required).
+* - Read of Cipher Ri register.
+*
+* Note: Any step that requires the writing of multiple registers are
+* "book ended" with the clearing and subsequent setting of the register update
+* bit within the Control register.
+*
+* -- -- -- -- -- -- -- -- -- -- -- -- --
+*
+* <b> HDCP REPEATER </b>
+*
+* The HDCP Repeater functionality is implemented in the drivers. Here however,
+* the user has to ensure that the right setup is available for the HDCP
+* repeater drivers.
+* - The use must also ensure that the variable IsRepeater in the instance
+*   of the structure XHdcp1x defined in the user application is set to 1. For
+*   example, DpRxSsInst.Hdcp1x->IsRepeater = 1.
+*
+* <b> Requirements </b>
+*
+* - The system has both the receiver and the transmitter interface.
+* - The IsRepeater variable of the hdcp core structure, XHdcp1x is set.
+* - The callbacks for Repeater are set in the user application.
+*
+* <b> Repeater State Machine for Transmitter </b>
+*
+* For the transmitter system, the repeater state machine has the following
+* states:
+*  - STATE_DISABLED
+*  - STATE_UNAUTHENTICATED
+*  - STATE_COMPUTATIONS
+*  - STATE_WAITFORDOWNSTREAM (in repeater only)
+*  - STATE_ASSEMBLEKSVLIST (in repeater only)
+*  - STATE_AUTHENTICATED
+*  - STATE_LINKINTEGRITYFAILED
+*  - STATE_PHYDOWN
+*
+*  For the receiver system, the repeater state machine has the following
+*  states:
+*  - STATE_DISABLED
+*  - STATE_DETERMINERXCAPABLE
+*  - STATE_EXCHANGEKSVS
+*  - STATE_COMPUTATIONS
+*  - STATE_VALIDATERX
+*  - STATE_AUTHENTICATED
+*  - STATE_LINKINTEGRITYCHECK
+*  - STATE_TESTFORREPEATER
+*  - STATE_WAITFORREADY (in repeater only)
+*  - STATE_READKSVLIST (in repeater only)
+*  - STATE_UNAUTHENTICATED
+*  - STATE_PHYDOWN
+*
+* <b> Repeater Flow </b>
+*
+* <pre>
+*   |> Receiver <|   |> User App <|        |> Transmitter <|
+*
+* -> AKSV Written
+*    to Receiver
+*       |
+*    Ro' written
+*    to upstream
+*       |
+*       ---->   Trigger Downstream
+*               (Hdcp1x.Rx.Repeater
+*               DownstreamAuthCallBack) ----> Transmitter writes
+*                                             AKSV and An downstream
+*                                                       |
+*                                             Transmitter reads back
+*                                             Ro' and completes
+*                                             first part of
+*                                             authentication
+*                                                       |
+*                               -----(No)---- Is Downstream Repeater?
+*                               |                       | (Yes)
+*                               |             Read the downstream KSV
+*                               |             FIFO, calculate the SHA-1
+*                               |             value and complete 2nd part
+*                               |             of authentication.
+*                               |
+*                               ------------> Setup the KSV FIFO for
+*                                             upstream.
+*                                                       |
+*               Exchange Repeater <----------------------
+*               Values (Hdcp1x.Tx.
+*               ExchangeRepeaterCallBack)
+*               Here Get the KSV
+*               FIFO and update it
+*               for the Receiver.
+*                       |
+*    Assemble the  <-----
+*    KSV List and
+*    calculate the SHA-1
+*    value and write
+*    it to upstream.
+*          |
+*    Goto Authenticated
+*    state.
+*
+* </pre>
+*
+* The Repeater authentication requires the presence of both RX and TX
+* interfaces. The authentication begins when the upstream transmitter writes
+* the An and AKSV to the RX interface. After completing the first part of
+* authentication the Receiver calls the DownstremaAuthCallBack callback
+* handler. This handler should be set in the user application and should post
+* the authenticate event to the TX state machine. This will trigger the TX
+* authentication process. The TX completes the first part of authentication,
+* by writing the AKSV and An downstreama and then reading an comparing the
+* downstream Ro' value. If the downstream device is also Repeater, then the
+* TX waits for the READY bit to get set in the downstream and reads the KSV
+* FIFO. The TX then commences the second part of the authentication, where it
+* calculates the SHA-1 value V and compares it with the V' read from the
+* downstream. If the SHA-1 value V matches with the V' value read from
+* downstream, authentication is successful. Here the TX sets up a
+* RepeaterExchange value which it populates with the KSV FIFO of the
+* downstream and the depth and device count values read from downstream. At
+* this point the KSV FIFO calls the ExchangeRepeaterCallBack, which needs to
+* be set in the user application. Here the user application receives the
+* KSV FIFO value, depth and device count from the TX of the downstream
+* topology. The user applicaition needs to update these value and set them
+* for the receiver. At this point the RX is expected to be in the
+* WAIT-FOR-READY state. Here the user should post EVENT_DOWNSTREAMREADY to the
+* RX state machine. Consequently, the RX state machine will
+* calculate the SHA-1 value, update the device count and depth value and set
+* the READY bit for the upstream transmitter device to read and complete the
+* authentication.
+*
+* If the authentication fails and the upstream device triggers the
+* authentication again, then the entire authenitcation process is re-started.
+*
+* <b> HDCP (Repeater) Callback functions </b>
+* - Transmitter
+*   - XHdcp1xInst.Tx.RepeaterExchangeCallback (Repeater)
+*   - XHdcp1xInst.Tx.UnauthenticatedCallback
+* - Receiver
+*   - XHdcp1xInst.Rx.RepeaterDownstreamAuthCallback (Repeater)
+*   - XHdcp1xInst.Rx.AuthenticatedCallback
+*   - XHdcp1xInst.Rx.UnauthenticatedCallback
+*   - XHdcp1xInst.Rx.TopologyUpdateCallback
+*   - XHdcp1xInst.Rx.EncryptionUpdateCallback
+*
+* Handler associated with each callback:
+* - XHdcp1xInst.Tx.RepeaterExchangeCallback
+*   - XHDCP1X_HANDLER_RPTR_RPTREXCHANGE
+*   - RepeaterExchangeCallback has to be defined by the user, in order to
+*     set get the KSV values from the downstream transmitter and set the
+*     values in the Receiver's Ksv List. This function is called by the
+*     drivers.
+* - XHdcp1xInst.Tx.UnauthenticatedCallback
+*   - XHDCP1X_HANDLER_UNAUTHENTICATED
+*   - UnauthenticatedCallback has to be defined by the user , to handle
+*     repeater situations where the transmitter state machine goes to the
+*     unauthenticate state.
+* - XHdcp1xInst.Rx.RepeaterDownstreamAuthCallback
+*   - XHDCP1X_HANDLER_RPTR_TRIGDWNSTRMAUTH
+*   - RepeaterDownstreamAuthCallback has to be defined by the user in order
+*     to ensure that the downstream is ready to begin afer 1st part of
+*     authentication is completed on the RX side. The user must ensure that
+*     TX is not in physical-layer-down state and consequently post the
+*     EVENT_AUTHENTICATE to the TX interface in order to begin the
+*     authentication process for the downstream TX interface. Called by the
+*     drivers.
+* - XHdcp1xInst.Rx.AuthenticatedCallback
+*   - XHDCP1X_HANDLER_AUTHENTICATED
+*   - AuthenticatedCallback has to be defined by the user and is called
+*     when the HDCP state machine has completed authentication.
+* - XHdcp1xInst.Rx.UnauthenticatedCallback
+*   - XHDCP1X_HANDLER_UNAUTHENTICATED
+*   - UnauthenticatedCallback has to be defined by the user , to handle
+*     repeater situations where the transmitter state machine goes to the
+*     unauthenticate state.
+* - XHdcp1xInst.Rx.TopologyUpdateCallback
+*   - XHDCP1X_HANDLER_TOPOLOGY_UPDATE
+*   - The TopologyUpdateCallback should be set by the user to handle changes
+*     in downstream topology. This is currently not supprted for hdcp 1.4.
+* - XHdcp1xInst.Rx.EncryptionUpdateCallback
+*   - XHDCP1X_HANDLER_ENCRYPTION_UPDATE
+*   - The EncryptionUpdateCallback needs to be set by the user and is called
+*     if the upstream device stops sending encrypted content to the receiver
+*     after authentication or vice-versa.
+*
+* -- -- -- -- -- -- -- -- -- -- -- -- --
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 2.00  als    09/30/15 Added EffectiveAddr argument to XHdcp1x_CfgInitialize.
+* 2.10  MG     01/18/16 Added function XHdcp1x_IsEnabled.
+* 2.20  MG     01/20/16 Added function XHdcp1x_GetHdcpCallback.
+* 2.30  MG     02/25/16 Added function XHdcp1x_SetCallback and
+*                       AuthenticatedCallback.
+* 2.40  MG     01/29/16 Removed function XHdcp1x_GetHdcpCallback and added
+*                       function XHdcp1x_ProcessAKsv
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added constants:
+*                       XHDCP1X_RPTR_MAX_CASCADE and
+*                       XHDCP1X_RPTR_MAX_DEVS_COUNT.
+*                       Added enumeration type:
+*                       XHdcp1x_RepeaterStateMachineHandlerType.
+*                       Added typedef data type XHdcp1x_Ksv.
+*                       Added structure XHdcp1x_RepeaterExchange.
+*                       Updated core structure XHdcp1x_Tx, XHdcp1x_Rx and
+*                       XHdcp1x for Repeater support.
+*                       Added following functions:
+*                       XHdcp1x_DownstreamReady, XHdcp1x_GetRepeaterInfo,
+*                       XHdcp1x_SetCallBack, XHdcp1x_ReadDownstream.
+* 4.0   yas    06/15/16 Added support for Cipher Blank Value and select.
+*                       Extended support for Repeater functionality.
+* 4.0   yas    08/16/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XHdcp1x_CfgInitialize
+* 4.1   yas    11/10/16 Added function XHdcp1x_SetHdmiMode.
+* 4.1   yas    08/03/17 Added flag IsAuthReqPending to the XHdcp1x_Tx data
+*                       structure to track any pending authentication requests.
+* 4.2   yas    13/08/18 Addded hdcp14_PropagateTopoErrUpstream flag to track
+*                       topology failures and ready the topology for the
+*                       repeater application to read.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_types.h"
+#include "xhdcp1x_hw.h"
+#include "xstatus.h"
+#include "xtmrctr.h"
+
+/************************** Constant Definitions *****************************/
+#define XHDCP1X_KSV_SIZE	5 /**< Size of each hdcp 1.4 Public Key
+				    *  in bytes */
+#define XHDCP1X_RPTR_MAX_CASCADE	4	/**< Maximum depth that the
+						  *  Repeater can support on
+						  *  the downstream
+						  *  interface */
+#define XHDCP1X_RPTR_MAX_DEVS_COUNT	32	/**< Maximum devices that can
+						  *  be cascaded to the
+						  *  Repeater */
+
+#define XHdcp1x_SetCallBack  XHdcp1x_SetCallback	/**< Alternative name
+							  *  for the function
+							  *  to set callback
+							  *  for HDCP
+							  *  functions */
+
+#define UNUSED(x)  ((void)x) /**< Used to remove warnings for
+			       *  unused variables. */
+#define XHDCP1X_ADDITIONAL_DEBUG  0 /**< Adds extra functions for
+				      *  additional debugging. */
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * This enumerates the State Types for HDCP Receiver state machine.
+ */
+enum XHdcp1x_Rx_StateType {
+	XHDCP1X_RX_STATE_DISABLED,
+	XHDCP1X_RX_STATE_UNAUTHENTICATED,
+	XHDCP1X_RX_STATE_COMPUTATIONS,
+	XHDCP1X_RX_STATE_WAITFORDOWNSTREAM,
+	XHDCP1X_RX_STATE_ASSEMBLEKSVLIST,
+	XHDCP1X_RX_STATE_AUTHENTICATED,
+	XHDCP1X_RX_STATE_LINKINTEGRITYFAILED,
+	XHDCP1X_RX_STATE_PHYDOWN,
+};
+
+/**
+ * This enumerates the Event Types for HDCP Transmitter state machine.
+ */
+enum XHdcp1x_Tx_StateType {
+	XHDCP1X_TX_STATE_DISABLED,
+	XHDCP1X_TX_STATE_DETERMINERXCAPABLE,
+	XHDCP1X_TX_STATE_EXCHANGEKSVS,
+	XHDCP1X_TX_STATE_COMPUTATIONS,
+	XHDCP1X_TX_STATE_VALIDATERX,
+	XHDCP1X_TX_STATE_AUTHENTICATED,
+	XHDCP1X_TX_STATE_LINKINTEGRITYCHECK,
+	XHDCP1X_TX_STATE_TESTFORREPEATER,
+	XHDCP1X_TX_STATE_WAITFORREADY,
+	XHDCP1X_TX_STATE_READKSVLIST,
+	XHDCP1X_TX_STATE_UNAUTHENTICATED,
+	XHDCP1X_TX_STATE_PHYDOWN,
+};
+
+/**
+ * These constants are used to identify callback functions.
+ */
+typedef enum
+{
+	XHDCP1X_HANDLER_UNDEFINED,
+	XHDCP1X_HANDLER_DDC_SETREGADDR,
+	XHDCP1X_HANDLER_DDC_SETREGDATA,
+	XHDCP1X_HANDLER_DDC_GETREGDATA,
+	XHDCP1X_HANDLER_DDC_WRITE,
+	XHDCP1X_HANDLER_DDC_READ,
+	XHDCP1X_HANDLER_AUTHENTICATED,
+	XHDCP1X_HANDLER_UNAUTHENTICATED,
+	XHDCP1X_HANDLER_RPTR_RPTREXCHANGE,
+	XHDCP1X_HANDLER_RPTR_TRIGDWNSTRMAUTH,
+	XHDCP1X_HANDLER_TOPOLOGY_UPDATE,
+	XHDCP1X_HANDLER_ENCRYPTION_UPDATE,
+	XHDCP1X_HANDLER_INVALID
+} XHdcp1x_HandlerType;
+
+/**
+ * This typedef defines the callback interface that is to be used for
+ * interrupts within this driver
+ */
+typedef void (*XHdcp1x_Callback)(void *CallbackRef);
+
+/**
+ * This typedef defines the function interface that is to be used for debug
+ * log message statements within this driver
+ */
+typedef void (*XHdcp1x_LogMsg)(const char *fmt, ...);
+
+/**
+ * This enumerates the call back for the HDCP Repeater Tx state machine
+ */
+typedef enum {
+	XHDCP1X_RPTR_HDLR_REPEATER_EXCHANGE =
+			XHDCP1X_HANDLER_RPTR_RPTREXCHANGE,
+	XHDCP1X_RPTR_HDLR_TRIG_DOWNSTREAM_AUTH =
+			XHDCP1X_HANDLER_RPTR_TRIGDWNSTRMAUTH,
+} XHdcp1x_RepeaterStateMachineHandlerType;
+
+/**
+* These constants are used to identify fields inside the topology structure
+*/
+typedef enum {
+	XHDCP1X_TOPOLOGY_DEPTH,
+	XHDCP1X_TOPOLOGY_DEVICECNT,
+	XHDCP1X_TOPOLOGY_MAXDEVSEXCEEDED,
+	XHDCP1X_TOPOLOGY_MAXCASCADEEXCEEDED,
+	XHDCP1X_TOPOLOGY_HDCP20REPEATERDOWNSTREAM,
+	XHDCP1X_TOPOLOGY_HDCP1DEVICEDOWNSTREAM,
+	XHDCP1X_TOPOLOGY_INVALID
+} XHdcp1x_TopologyField;
+
+/**
+* Callback type used for calling DDC read and write functions.
+*
+* @param  DeviceAddress is the (i2c) device address of the HDCP port.
+* @param  ByteCount is the amount of data bytes in the buffer to read or write.
+* @param  BufferPtr is a pointer to a buffer that is used
+*         for reading or writing.
+* @param  Stop is a flag to control if a stop token is set or not.
+* @param  RefPtr is a callback reference passed in by the
+*         upper layer when setting the DDC reading and writing functions,
+*         and passed back to the upper layer when the callback is invoked.
+*
+* @return
+*         - XST_SUCCESS The read action was successful.
+*         - XST_FAILURE The read action failed.
+*
+* @note   None.
+*
+*/
+typedef int (*XHdcp1x_RunDdcHandler)(u8 DeviceAddress, u16 ByteCount,
+		u8* BufferPtr, u8 Stop, void *RefPtr);
+
+/**
+ * This typedef defines the function interface that is to be used for setting
+ * the DDC handler for HDMI implementation of HDCP functionality over HDMI
+ * within this driver
+ */
+typedef void (*XHdcp1x_SetDdcHandler)(void *HandlerRef, u32 Data);
+
+/**
+ * This typedef defines the function interface that is to be used to get
+ * the DDC handler for implementation of HDCP functionality over HDMI
+ * within this driver
+ */
+typedef u32 (*XHdcp1x_GetDdcHandler)(void *HandlerRef);
+
+/**
+* This typedef contains configuration information for the HDCP core.
+*/
+typedef struct {
+	u16 DeviceId;		/**< Device instance ID. */
+	UINTPTR BaseAddress;	/**< The base address of the core  */
+	u32 SysFrequency;	/**< The main clock frequency of the core */
+	u16 IsRx;		/**< Flag indicating the core direction */
+	u16 IsHDMI;		/**< Flag indicating if the core is meant to
+				  *  work with HDMI. */
+} XHdcp1x_Config;
+
+/**
+* This typedef defines the statistics collected by a cipher instance
+*/
+typedef struct {
+	u32 IntCount;		/**< The number of interrupts detected */
+} XHdcp1x_CipherStats;
+
+/**
+* This typedef contains an instance of the HDCP cipher core
+*/
+typedef struct {
+	XHdcp1x_Callback LinkFailCallback;	/**< Link fail callback */
+	void *LinkFailRef;			/**< Link fail reference */
+	u32 IsLinkFailCallbackSet;		/**< Link fail config flag */
+	XHdcp1x_Callback RiUpdateCallback;	/**< Ri update callback */
+	void *RiUpdateRef;			/**< Ri update reference */
+	u32 IsRiUpdateCallbackSet;		/**< Ri update config flag */
+	XHdcp1x_CipherStats Stats;		/**< Cipher statistics */
+} XHdcp1x_Cipher;
+
+/**
+ * This typedef defines the statistics collected by a port instance
+ */
+typedef struct {
+	u32 IntCount;		/**< The number of interrupts detected */
+} XHdcp1x_PortStats;
+
+/**
+ * Forward declaration of a structure defined within xhdcxp1x_port.h
+ */
+struct XHdcp1x_PortPhyIfAdaptorS;
+
+/**
+ * This typedef defines a memory to store a Key Selection Vector (KSV)
+ */
+typedef u64 XHdcp1x_Ksv;
+
+/**
+ * This typedef contains an instance of the HDCP Repeater values to
+ * exchanged between HDCP Tx and HDCP Rx
+ */
+typedef struct {
+	u32 V[5];	/**< 20 bytes value of SHA 1 hash, V'H0, V'H1, V'H2 ,
+			  *  V'H3 ,V'H4 read from the downstream Repeater*/
+	XHdcp1x_Ksv KsvList[32];	/**< An array of 32 elements each
+					  *  of 64 bits to store the KSVs
+					  *  for the KSV FIFO*/
+	u8 Depth;	/**< Depth of the Repeater's downstream topology*/
+	u8 DeviceCount;		/**< Number of downstream devices attached
+				  *  to the Repeater*/
+	u8 hdcp14_PropagateTopoErrUpstream;
+} XHdcp1x_RepeaterExchange;
+
+/**
+ * This typedef contains an instance of the HDCP port
+ */
+typedef struct XHdcp1x_PortStruct {
+	const struct XHdcp1x_PortPhyIfAdaptorS *Adaptor; /**< Port adaptor */
+	void *PhyIfPtr;		/**< The port's physical interface */
+	XHdcp1x_Callback AuthCallback;	/**< (Re)Authentication callback */
+	void *AuthRef;		/**< (Re)Authentication reference */
+	u32 IsAuthCallbackSet;		/**< (Re)Authentication config flag */
+	XHdcp1x_PortStats Stats;	/**< Port statistics */
+} XHdcp1x_Port;
+
+/**
+ * This typedef defines the statistics collected transmit port instance
+ */
+typedef struct {
+	u32 AuthFailed;		/**< Num of failed authentication attempts */
+	u32 AuthPassed;		/**< Num of passed authentication attempts */
+	u32 ReauthRequested;	/**< Num of rxd re-authentication requests */
+	u32 ReadFailures;	/**< Num of remote read failures */
+	u32 LinkCheckPassed;	/**< Num of link verifications that passed */
+	u32 LinkCheckFailed;	/**< Num of link verifications that failed */
+} XHdcp1x_TxStats;
+
+/**
+ * This typedef defines the statistics collected receive port instance
+ */
+typedef struct {
+	u32 AuthAttempts;	/**< Num of rxd authentication requests */
+	u32 LinkFailures;	/**< Num of link verifications that failed */
+	u32 RiUpdates;		/**< Num of Ri updates performed */
+} XHdcp1x_RxStats;
+
+/**
+ * This typedef is used to keep a tab on the changes in the encryption
+ * status of the HDCP receiver, depending on whether the incoming
+ * data non the receiver is HDCP protected or not.
+ */
+typedef struct {
+	u8 PreviousState;	/**< Previous state of encryption */
+	u8 CurrentState;	/**< Current state of encryption */
+} XHdcp1x_RxEncyptionWatch;
+
+/**
+ * This typedef contains the transmit HDCP interface
+ */
+typedef struct {
+	u32 CurrentState;	/**< The interface's current state */
+	u32 PreviousState;	/**< The interface's previous state */
+	u64 StateHelper;	/**< The interface's state helper */
+	u16 Flags;		/**< The interface flags */
+	u16 PendingEvents;	/**< The bit map of pending events */
+	u64 EncryptionMap;	/**< The configured encryption map */
+	u16 WaitForReadyPollCntFlag; /**< Count of the times we have
+				  * polled the BCaps every 100ms interval. */
+	XHdcp1x_TxStats Stats;	/**< The interface's statistics */
+	u8 TxIsHdmi;	/**< Flag determines if TX is HDMI or DVI */
+	u8 IsAuthReqPending; /**< Flag to track if a auth request is alive */
+	XHdcp1x_Callback AuthenticatedCallback;	/**< Authentication callback */
+	void *AuthenticatedCallbackRef;	/**< Authentication reference */
+	u32 IsAuthenticatedCallbackSet;	/**< Authentication config flag */
+	XHdcp1x_RunDdcHandler DdcRead;	/**< Function pointer for reading DDC*/
+	void *DdcReadRef;	/**< Reference pointer set with
+				  *  XHdcp1x_SetCallback function. */
+	u8 IsDdcReadSet;	/**< Set if DdcRead handler is defined. */
+	XHdcp1x_RunDdcHandler DdcWrite;	/**< Function pointer for writing DDC*/
+	void *DdcWriteRef;	/**< Reference pointer set with
+				  *  XHdcp1x_SetCallback function. */
+	u8 IsDdcWriteSet;	/**< Set if DdcWrite handler is defined. */
+	XHdcp1x_Callback RepeaterExchangeCallback; /**< (Repeater)Exchange
+						     *  Repeater Values
+						     *  callback */
+	void *RepeaterExchangeRef;	/**< (Repeater)Exchange Repeater
+					  *  Values reference */
+	u32 IsRepeaterExchangeCallbackSet;	/**< (Repeater)Check to
+						  *  determine if Exchange
+						  *  Repeater Values
+						  *  callback is set flag */
+	XHdcp1x_Callback UnauthenticatedCallback; /**< Unauthenticated
+						    * callback */
+	void *UnauthenticatedCallbackRef;	/**< Unauthenticated
+						  *  reference */
+	u32 IsUnauthenticatedCallbackSet;	/**< Unauthenticated config
+						  *  flag */
+	u16 DownstreamReady;/**< The downstream interface's status flag */
+} XHdcp1x_Tx;
+
+/**
+ * This typedef contains the receive HDCP interface
+ */
+typedef struct {
+	u32 CurrentState;		/**< The interface's current state */
+	u32 PreviousState;		/**< The interface's previous state */
+	u16 Flags;			/**< The interface flags */
+	u16 PendingEvents;		/**< The bit map of pending events */
+	XHdcp1x_RxStats Stats;		/**< The interface's statistics */
+	XHdcp1x_RxEncyptionWatch XORState;	/**< The interface's encryption
+						  *  state */
+	XHdcp1x_SetDdcHandler DdcSetAddressCallback; /**< Function pointer for
+						       *  setting DDC register
+						       *  address */
+	void *DdcSetAddressCallbackRef;	/**< To be passed to callback
+					  *  function */
+	u8 IsDdcSetAddressCallbackSet;	/**< This flag is set true when the
+					  *  callback has been registered */
+	XHdcp1x_SetDdcHandler DdcSetDataCallback; /**< Function pointer for
+						    *  setting DDC register
+						    *  data */
+	void *DdcSetDataCallbackRef;	/**< To be passed to callback
+					  *  function */
+	u8 IsDdcSetDataCallbackSet;	/**< This flag is set true when the
+					  *  callback has been registered */
+	XHdcp1x_GetDdcHandler DdcGetDataCallback; /**< Function pointer for
+						    *  getting DDC register
+						    *  data */
+	void *DdcGetDataCallbackRef;	/**< To be passed to callback
+					  *  function */
+	u8 IsDdcGetDataCallbackSet;	/**< This flag is set true when the
+					  *  callback has been registered */
+	XHdcp1x_Callback RepeaterDownstreamAuthCallback; /**< (Repeater)Post
+							   *  authenticate to
+							   *  downstream,
+							   *  second part of
+							   *  authentication
+							   *  start callback*/
+	void *RepeaterDownstreamAuthRef; /**< (Repeater)Post authenticate to
+					   *  downstream, second part of
+					   *  authentication start reference */
+	u32 IsRepeaterDownstreamAuthCallbackSet; /**< (Repeater)Is "Post
+						   *  authenticate to
+						   *  downstream to trigger
+						   *  second part of
+						   *  authentication" callback
+						   *  set flag*/
+	XHdcp1x_Callback AuthenticatedCallback; /**< Authenticated callback*/
+	void *AuthenticatedCallbackRef;	/**< Authenticated reference */
+	u32 IsAuthenticatedCallbackSet;	/**< Authenticated config flag */
+	XHdcp1x_Callback UnauthenticatedCallback; /**< Unauthenticated
+						    *  callback */
+	void *UnauthenticatedCallbackRef;	/**< Unauthenticated
+						  *  reference */
+	u32 IsUnauthenticatedCallbackSet;	/**< Unauthenticated config
+						  *  flag */
+	XHdcp1x_Callback TopologyUpdateCallback; /**< Topology Update
+						   *  callback */
+	void *TopologyUpdateCallbackRef;	/**< Topology Update
+						  *  reference */
+	u32 IsTopologyUpdateCallbackSet;	/**< Topology Update config
+						  *  flag */
+	XHdcp1x_Callback EncryptionUpdateCallback; /**< Encryption Update
+						     *  callback */
+	void *EncryptionUpdateCallbackRef;	/**< Encryption Update
+						  *  reference */
+	u32 IsEncryptionUpdateCallbackSet;	/**< Encryption Update
+						  *  config flag */
+} XHdcp1x_Rx;
+
+/**
+ * This typedef defines the function interface that is to be used
+ * for starting a one shot timer on behalf of an HDCP interface within
+ * the underlying platform
+ */
+typedef int (*XHdcp1x_TimerStart)(void *InstancePtr, u16 TmoInMs);
+
+/**
+ * This typedef defines the function interface that is to be used
+ * for stopping a timer on behalf of an HDCP interface
+ */
+typedef int (*XHdcp1x_TimerStop)(void *InstancePtr);
+
+/**
+ * This typedef defines the function interface that is to be used for
+ * performing a busy delay on behalf of an HDCP interface
+ */
+typedef int (*XHdcp1x_TimerDelay)(void *InstancePtr, u16 DelayInMs);
+
+/**
+ * This typedef contains an instance of an HDCP interface
+ */
+typedef struct {
+	XHdcp1x_Config Config;	/**< The core config */
+	XHdcp1x_Cipher Cipher;	/**< The interface's cipher */
+	XHdcp1x_Port Port;	/**< The interface's port */
+	union {
+		XHdcp1x_Tx Tx;	/**< The transmit interface elements */
+		XHdcp1x_Rx Rx;	/**< The receive interface elements */
+	};
+	u32 IsReady;		/**< The ready flag */
+	u32 IsRepeater;		/**< The IsRepeater flag determines if the
+				  *  HDCP is part of a Repeater system
+				  *  or a non-repeater interface */
+	XHdcp1x_RepeaterExchange RepeaterValues; /**< The Repeater value to
+						   *  be exchanged between
+						   *  Tx and Rx */
+	void *Hdcp1xRef;	/**< A void reference pointer for
+				  *  association of a external core
+				  *  in our case a timer with the
+				  *  HDCP instance */
+	XHdcp1x_TimerStart XHdcp1xTimerStart; 	/**< Instance of function
+						*  interface used for
+						*  starting a timer on behalf
+						*  of an HDCP interface*/
+	XHdcp1x_TimerStop XHdcp1xTimerStop; 	/**< Instance of function
+						*  interface used for
+						*  stopping a timer on behalf
+						*  of an HDCP interface*/
+	XHdcp1x_TimerDelay XHdcp1xTimerDelay;	/**< Instance of function
+						*  interface used for
+						*  performing a busy delay on
+						*  behalf of an HDCP
+						*  interface*/
+} XHdcp1x;
+
+/**
+ * This typedef defines the function interface that is to be used
+ * for checking a specific KSV against the platforms revocation list
+ */
+typedef int (*XHdcp1x_KsvRevokeCheck)(const XHdcp1x *InstancePtr, u64 Ksv);
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Prototypes ******************************/
+
+XHdcp1x_Config *XHdcp1x_LookupConfig(u16 DeviceId);
+
+int XHdcp1x_CfgInitialize(XHdcp1x *InstancePtr, const XHdcp1x_Config *CfgPtr,
+		void *PhyIfPtr, UINTPTR EffectiveAddr);
+void XHdcp1x_LateInit(XHdcp1x *InstancePtr);
+
+int XHdcp1x_SelfTest(XHdcp1x *InstancePtr);
+
+int XHdcp1x_Poll(XHdcp1x *InstancePtr);
+
+int XHdcp1x_DownstreamReady(XHdcp1x *InstancePtr);
+int XHdcp1x_GetRepeaterInfo(XHdcp1x *InstancePtr,
+		XHdcp1x_RepeaterExchange *RepeaterInfoPtr);
+int XHdcp1x_SetRepeater(XHdcp1x *InstancePtr, u8 State);
+
+int XHdcp1x_Reset(XHdcp1x *InstancePtr);
+int XHdcp1x_Enable(XHdcp1x *InstancePtr);
+int XHdcp1x_Disable(XHdcp1x *InstancePtr);
+
+int XHdcp1x_SetPhysicalState(XHdcp1x *InstancePtr, int IsUp);
+int XHdcp1x_SetLaneCount(XHdcp1x *InstancePtr, int LaneCount);
+
+int XHdcp1x_Authenticate(XHdcp1x *InstancePtr);
+int XHdcp1x_ReadDownstream(XHdcp1x *InstancePtr);
+int XHdcp1x_IsInProgress(const XHdcp1x *InstancePtr);
+int XHdcp1x_IsAuthenticated(const XHdcp1x *InstancePtr);
+int XHdcp1x_IsInComputations(const XHdcp1x *InstancePtr);
+int XHdcp1x_IsInWaitforready(const XHdcp1x *InstancePtr);
+int XHdcp1x_IsDwnstrmCapable(const XHdcp1x *InstancePtr);
+int XHdcp1x_IsEnabled(const XHdcp1x *InstancePtr);
+
+u64 XHdcp1x_GetEncryption(const XHdcp1x *InstancePtr);
+int XHdcp1x_IsEncrypted(const XHdcp1x *InstancePtr);
+int XHdcp1x_EnableEncryption(XHdcp1x *InstancePtr, u64 StreamMap);
+int XHdcp1x_DisableEncryption(XHdcp1x *InstancePtr, u64 StreamMap);
+
+int XHdcp1x_SetKeySelect(XHdcp1x *InstancePtr, u8 KeySelect);
+
+void XHdcp1x_HandleTimeout(void *InstancePtr);
+
+int XHdcp1x_SetCallback(XHdcp1x *InstancePtr,
+		XHdcp1x_HandlerType HandlerType,
+		void *CallbackFunc, void *CallbackRef);
+void XHdcp1x_CipherIntrHandler(void *InstancePtr);
+void XHdcp1x_PortIntrHandler(void *InstancePtr, u32 IntCause);
+
+void XHdcp1x_SetDebugLogMsg(XHdcp1x_LogMsg LogFunc);
+
+void XHdcp1x_SetKsvRevokeCheck(XHdcp1x_KsvRevokeCheck RevokeCheckFunc);
+void XHdcp1x_SetTimerStart(XHdcp1x *InstancePtr,
+		XHdcp1x_TimerStart TimerStartFunc);
+void XHdcp1x_SetTimerStop(XHdcp1x *InstancePtr,
+		XHdcp1x_TimerStop TimerStopFunc);
+void XHdcp1x_SetTimerDelay(XHdcp1x *InstancePtr,
+		XHdcp1x_TimerDelay TimerDelayFunc);
+
+u32 XHdcp1x_GetDriverVersion(void);
+u32 XHdcp1x_GetVersion(const XHdcp1x *InstancePtr);
+void XHdcp1x_Info(const XHdcp1x *InstancePtr);
+void XHdcp1x_ProcessAKsv(XHdcp1x *InstancePtr);
+
+void *XHdcp1x_GetTopology(XHdcp1x *InstancePtr);
+void XHdcp1x_DisableBlank(XHdcp1x *InstancePtr);
+void XHdcp1x_EnableBlank(XHdcp1x *InstancePtr);
+void XHdcp1x_SetTopologyField(XHdcp1x *InstancePtr,
+		XHdcp1x_TopologyField Field, u8 Value);
+u32 XHdcp1x_GetTopologyField(XHdcp1x *InstancePtr,
+		XHdcp1x_TopologyField Field);
+u8 *XHdcp1x_GetTopologyKSVList(XHdcp1x *InstancePtr);
+u8 *XHdcp1x_GetTopologyBKSV(XHdcp1x *InstancePtr);
+int XHdcp1x_IsRepeater(XHdcp1x *InstancePtr);
+
+void XHdcp1x_SetTopology(XHdcp1x *InstancePtr,
+		const XHdcp1x_RepeaterExchange *TopologyPtr);
+void XHdcp1x_SetTopologyKSVList(XHdcp1x *InstancePtr, u8 *ListPtr,
+		u32 ListSize);
+void XHdcp1x_SetTopologyUpdate(XHdcp1x *InstancePtr);
+void XHdcp1x_SetHdmiMode(XHdcp1x *InstancePtr, u8 Value);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_cipher.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_cipher.c
@@ -0,0 +1,1297 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_cipher.c
+* @{
+*
+* This file contains the main implementation of the driver associated with
+* the Xilinx HDCP Cipher core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 3.1   yas    06/14/16 Added new functions XHdcp1x_CipherEnableBlank
+*                       and XHdcp1x_CipherDisableBlank
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+#include "xil_assert.h"
+#include "xil_types.h"
+#include "xhdcp1x_debug.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*************************** Function Prototypes *****************************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function initializes an HDCP cipher.
+*
+* @param	InstancePtr is the device to initialize.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_CipherInit(XHdcp1x *InstancePtr)
+{
+	u32 Value = 0;
+
+	/* Reset it */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_RESET;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_RESET;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Ensure all interrupts are disabled and cleared */
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_INTERRUPT_MASK, (u32)(-1));
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_INTERRUPT_STATUS, (u32)(-1));
+
+	/* Check for DP */
+	if (XHdcp1x_IsDP(InstancePtr)) {
+		/* Configure for four lanes SST */
+		Value  = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL);
+		Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_NUM_LANES;
+		Value |= (4u << 4);
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL, Value);
+	}
+
+	/* Ensure that the register update bit is set */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+}
+
+/*****************************************************************************/
+/**
+* This function queries the link state of a cipher device.
+*
+* @param	InstancePtr is	the device to query.
+*
+* @return	Truth value.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherIsLinkUp(const XHdcp1x *InstancePtr)
+{
+	u32 Value;
+	int IsUp = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check for currently enabled */
+	if (XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_STATUS);
+		if ((Value &
+			XHDCP1X_CIPHER_BITMASK_INTERRUPT_LINK_FAIL) != 0) {
+			IsUp = TRUE;
+		}
+	}
+
+	return (IsUp);
+}
+
+/*****************************************************************************/
+/**
+* This function enables a HDCP cipher.
+*
+* @param	InstancePtr is the device to enable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherEnable(XHdcp1x *InstancePtr)
+{
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check for currently disabled */
+	if (XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_FAILURE);
+	}
+
+	/* Clear the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Ensure that all encryption is disabled for now */
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H, 0x00ul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L, 0x00ul);
+
+	/* Ensure that XOR is disabled on tx and enabled for rx to start */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_XOR_ENABLE;
+	if (XHdcp1x_IsRX(InstancePtr)) {
+		Value |= XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_XOR_ENABLE;
+	}
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL, Value);
+
+	/* Enable it */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_ENABLE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Ensure that the register update bit is set */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables a HDCP cipher.
+*
+* @param	InstancePtr is the device to disable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherDisable(XHdcp1x *InstancePtr)
+{
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Ensure all interrupts are disabled */
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_INTERRUPT_MASK, 0xFFFFFFFFul);
+
+	/* Enable bypass operation */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_ENABLE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Ensure that all encryption is disabled for now */
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H, 0x00ul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L, 0x00ul);
+
+	/* Ensure that XOR is disabled */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_XOR_ENABLE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL, Value);
+
+	/* Ensure that the register update bit is set */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function configures the key selection value.
+*
+* @param	InstancePtr is the device to configure.
+* @param	KeySelect is the desired key select value.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetKeySelect(XHdcp1x *InstancePtr, u8 KeySelect)
+{
+	int Status = XST_SUCCESS;
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(KeySelect < 8);
+
+	/* Update the device */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_SET_SELECT;
+	Value |= (KeySelect << 16);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Value);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initiates a request within the HDCP cipher.
+*
+* @param	InstancePtr is the device to submit the request to.
+* @param	Request is the request to submit.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLE if the core is disabled.
+*		- XST_DEVICE_BUSY if the core is busy.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherDoRequest(XHdcp1x *InstancePtr,
+		XHdcp1x_CipherRequestType Request)
+{
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Request < (XHDCP1X_CIPHER_REQUEST_MAX));
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Determine if there is a request in progress */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_STATUS);
+	Value &= XHDCP1X_CIPHER_BITMASK_CIPHER_STATUS_REQUEST_IN_PROG;
+
+	/* Check that it is not busy */
+	if (Value != 0) {
+		return (XST_DEVICE_BUSY);
+	}
+
+	/* Ensure that the register update bit is set */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Set the appropriate request bit
+	 * and ensure that Km is always used
+	 */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_REQUEST;
+	Value |= (XHDCP1X_CIPHER_VALUE_CIPHER_CONTROL_REQUEST_BLOCK
+								<< Request);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL, Value);
+
+	/* Ensure that the request bit(s) get cleared for next time */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_REQUEST;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL, Value);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function queries the progress of the current request.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	Truth value.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherIsRequestComplete(const XHdcp1x *InstancePtr)
+{
+	u32 Value = 0;
+	int IsComplete = TRUE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Value */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_STATUS);
+	Value &= XHDCP1X_CIPHER_BITMASK_CIPHER_STATUS_REQUEST_IN_PROG;
+
+	/* Update IsComplete */
+	if (Value != 0) {
+		IsComplete = FALSE;
+	}
+
+	return (IsComplete);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the current number of lanes of the HDCP cipher.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The current number of lanes.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdcp1x_CipherGetNumLanes(const XHdcp1x *InstancePtr)
+{
+	u32 NumLanes = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check for currently enabled */
+	if (XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		/* Determine NumLanes */
+		NumLanes = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL);
+		NumLanes &= XHDCP1X_CIPHER_BITMASK_CONTROL_NUM_LANES;
+		NumLanes >>= 4;
+	}
+
+	return (NumLanes);
+}
+
+/*****************************************************************************/
+/**
+* This function configures the number of lanes of the HDCP cipher.
+*
+* @param	InstancePtr is the device to configure.
+* @param	NumLanes is the number of lanes to configure.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetNumLanes(XHdcp1x *InstancePtr, u32 NumLanes)
+{
+	int Status = XST_SUCCESS;
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(NumLanes > 0);
+	Xil_AssertNonvoid(NumLanes <= 4);
+
+	/* Check for HDMI */
+	if (XHdcp1x_IsHDMI(InstancePtr)) {
+		/* Verify NumLanes (again) */
+		Xil_AssertNonvoid(NumLanes == 1);
+
+		/* Update the control register */
+		Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL);
+		Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_NUM_LANES;
+		Value |= (NumLanes << 4);
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL, Value);
+	}
+	/* Otherwise - must be DP */
+	else {
+		/* Verify NumLanes (again) */
+		Xil_AssertNonvoid(NumLanes != 3);
+
+		/* Update the control register */
+		Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL);
+		Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_NUM_LANES;
+		Value |= (NumLanes << 4);
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CONTROL, Value);
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the current encryption stream map.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The current encryption stream map.
+*
+* @note		In the case of the receiver version of this core, the XOR in
+*		progress bit needs to be checked as well as the encryption map
+*		to fully determine if encryption is enabled for the SST case.
+*		This is the reason for the additional check in this code.
+*
+******************************************************************************/
+u64 XHdcp1x_CipherGetEncryption(const XHdcp1x *InstancePtr)
+{
+	u64 StreamMap = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (StreamMap);
+	}
+
+	/* Determine StreamMap */
+	StreamMap  = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H);
+	StreamMap <<= 32;
+	StreamMap |= XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L);
+
+	/* Check for special case of just XOR in progress */
+	if ((StreamMap == 0) &&
+			(XHdcp1x_CipherXorInProgress(InstancePtr))) {
+		StreamMap = 0x01ul;
+	}
+
+	return (StreamMap);
+}
+
+/*****************************************************************************/
+/**
+* This function enables encryption on a set of streams.
+*
+* @param	InstancePtr is the device to configure.
+* @param	StreamMap is the bit map of streams to enable encryption on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLE if the core is not enabled.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherEnableEncryption(XHdcp1x *InstancePtr, u64 StreamMap)
+{
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Check that it is not a receiver */
+	if (XHdcp1x_IsRX(InstancePtr)) {
+		return (XST_FAILURE);
+	}
+
+	/* Check for nothing to do */
+	if (StreamMap == 0) {
+		return (XST_SUCCESS);
+	}
+
+	/* Clear the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Update the LS 32-bits */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L);
+	Value |= ((u32) (StreamMap & 0xFFFFFFFFul));
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L, Value);
+
+	/* Write the MS 32-bits */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H);
+	Value |= ((u32) ((StreamMap >> 32) & 0xFFFFFFFFul));
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H, Value);
+
+	/* Ensure that the XOR is enabled */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_XOR_ENABLE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_CONTROL, Value);
+
+	/* Set the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Check if XORInProgress bit is set in the status register*/
+	if (!XHdcp1x_CipherXorInProgress(InstancePtr)) {
+		/* Do nothing for now. We can depend on the Cipher
+		 * to set the XorInProgress in status register when
+		 * we receive protected content. */
+	}
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function disables encryption on a set of streams.
+*
+* @param	InstancePtr is the device to configure.
+* @param	StreamMap is the bit map of streams to disable encryption on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLE if the core is not enabled.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherDisableEncryption(XHdcp1x *InstancePtr, u64 StreamMap)
+{
+	u32 Val = 0;
+	int DisableXor = TRUE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Check that it is not a receiver */
+	if (XHdcp1x_IsRX(InstancePtr)) {
+		return (XST_FAILURE);
+	}
+
+	/* Check for nothing to do */
+	if (StreamMap == 0) {
+		return (XST_SUCCESS);
+	}
+
+	/* Clear the register update bit */
+	Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Val &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Val);
+
+	/* Update the LS 32-bits */
+	Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L);
+	Val &= ~((u32) (StreamMap & 0xFFFFFFFFul));
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L, Val);
+	if (Val != 0) {
+		DisableXor = FALSE;
+	}
+
+	/* Write the MS 32-bits */
+	Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H);
+	Val &= ~((u32) ((StreamMap >> 32) & 0xFFFFFFFFul));
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H, Val);
+	if (Val != 0) {
+		DisableXor = FALSE;
+	}
+
+	/* Check HDMI special case */
+	if (XHdcp1x_IsHDMI(InstancePtr)) {
+		DisableXor = TRUE;
+	}
+
+	/* Check for XOR disable */
+	if (DisableXor) {
+		Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_CONTROL);
+		Val &= ~XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_XOR_ENABLE;
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_CONTROL, Val);
+	}
+
+	/* Set the register update bit */
+	Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Val |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Val);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the local KSV value from the cipher.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The local KSV value.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_CipherGetLocalKsv(const XHdcp1x *InstancePtr)
+{
+	u32 Val = 0;
+	u32 Guard = 0x400ul;
+	u64 Ksv = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (Ksv);
+	}
+
+	/* Check if the local ksv is not available */
+	Val  = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KEYMGMT_STATUS);
+	Val &= XHDCP1X_CIPHER_BITMASK_KEYMGMT_STATUS_KSV_READY;
+	if (Val == 0) {
+		/* Abort any running Km calculation just in case */
+		Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL);
+		Val |= XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_ABORT_Km;
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Val);
+		Val &= ~XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_ABORT_Km;
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Val);
+
+		/* Load the local ksv */
+		Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL);
+		Val |= XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_LOCAL_KSV;
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Val);
+		Val &= ~XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_LOCAL_KSV;
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Val);
+
+		/* Wait until local KSV available */
+		while ((!XHdcp1x_CipherLocalKsvReady(InstancePtr)) &&
+			(--Guard > 0));
+	}
+
+	/* Confirm no timeout */
+	if (Guard != 0) {
+		/* Update Ksv */
+		Ksv = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KSV_LOCAL_H);
+		Ksv &= 0xFFul;
+		Ksv <<= 32;
+		Ksv |= XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_KSV_LOCAL_L);
+	}
+
+	return (Ksv);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the remote KSV value from the cipher.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The remote KSV value.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_CipherGetRemoteKsv(const XHdcp1x *InstancePtr)
+{
+	u64 Ksv = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Ksv */
+	Ksv = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KSV_REMOTE_H);
+	Ksv <<= 32;
+	Ksv |= XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KSV_REMOTE_L);
+
+	return (Ksv);
+}
+
+/*****************************************************************************/
+/**
+* This function writes the remote KSV value to the cipher.
+*
+* @param	InstancePtr is the device to write to.
+* @param	Ksv is the remote KSV value to write.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLED otherwise.
+*
+* @note		Whenever this function is called, the underlying driver will
+*		initiate the calculation of the Km value and wait for it to
+*		complete.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetRemoteKsv(XHdcp1x *InstancePtr, u64 Ksv)
+{
+	u32 Value = 0;
+	u32 Guard = 0x400ul;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Read local ksv to put things into a known state */
+	XHdcp1x_CipherGetLocalKsv(InstancePtr);
+
+	/* Clear the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Write the LS 32-bits */
+	Value = (u32)(Ksv & 0xFFFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KSV_REMOTE_L, Value);
+
+	/* Write the MS 8-bits */
+	Value = (u32)((Ksv >> 32) & 0xFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KSV_REMOTE_H, Value);
+
+	/* Set the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Trigger the calculation of theKm */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL);
+	Value &= 0xFFFFFFF0ul;
+	Value |= XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_BEGIN_Km;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Value);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_BEGIN_Km;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL, Value);
+
+	/* Wait until Km is available */
+	while ((!XHdcp1x_CipherKmReady(InstancePtr)) && (--Guard > 0));
+
+	/* Check for timeout */
+	if (Guard == 0) {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the contents of the B register in BM0.
+*
+* @param	InstancePtr is the device to query.
+* @param	X is to be loaded with the contents of Bx.
+* @param	Y is to be loaded with the contents of By.
+* @param	Z is to be loaded with the contents of Bz.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLED otherwise.
+*
+* @note		A NULL pointer can be passed in any of X, Y and Z.  If so, then
+*		this portion of the B register is not returned to the caller.
+*
+******************************************************************************/
+int XHdcp1x_CipherGetB(const XHdcp1x *InstancePtr, u32 *X, u32 *Y, u32 *Z)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Get X if requested */
+	if (X != NULL) {
+		*X = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_Bx);
+		*X &= 0x0FFFFFFFul;
+	}
+
+	/* Get Y if requested */
+	if (Y != NULL) {
+		*Y = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_By);
+		*Y &= 0x0FFFFFFFul;
+	}
+
+	/* Get Z if requested */
+	if (Z != NULL) {
+		*Z = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_Bz);
+		*Z &= 0x0FFFFFFFul;
+	}
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function writes the contents of the B register in BM0.
+*
+* @param	InstancePtr is the device to write to.
+* @param	X is the value to be written to Bx.
+* @param	Y is the value to be written to By.
+* @param	Z is the value to be written to Bz.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLED otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetB(XHdcp1x *InstancePtr, u32 X, u32 Y, u32 Z)
+{
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Clear the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Update the Bx */
+	Value = (X & 0x0FFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Bx, Value);
+
+	/* Update the By */
+	Value = (Y & 0x0FFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_By, Value);
+
+	/* Update the Bz */
+	Value = (Z & 0x0FFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Bz, Value);
+
+	/* Set the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the contents of the K register in BM0.
+*
+* @param	InstancePtr is the device to query.
+* @param	X is to be loaded with the contents of Kx.
+* @param	Y is to be loaded with the contents of Ky.
+* @param	Z is to be loaded with the contents of Kz.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLED otherwise.
+*
+* @note		A NULL pointer can be passed in any of X, Y and Z. If so,
+*		then this portion of the K register is not returned
+*		to the caller.
+*
+******************************************************************************/
+int XHdcp1x_CipherGetK(const XHdcp1x *InstancePtr, u32 *X, u32 *Y, u32 *Z)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Get X if requested */
+	if (X != NULL) {
+		*X = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_Kx);
+		*X &= 0x0FFFFFFFul;
+	}
+
+	/* Get Y if requested */
+	if (Y != NULL) {
+		*Y = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_Ky);
+		*Y &= 0x0FFFFFFFul;
+	}
+
+	/* Get Z if requested */
+	if (Z != NULL) {
+		*Z = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_CIPHER_Kz);
+		*Z &= 0x0FFFFFFFul;
+	}
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function writes the contents of the K register in BM0.
+*
+* @param	InstancePtr is the device to write to.
+* @param	X is the value to be written to Kx.
+* @param	Y is the value to be written to Ky.
+* @param	Z is the value to be written to Kz.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NOT_ENABLED otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetK(XHdcp1x *InstancePtr, u32 X, u32 Y, u32 Z)
+{
+	u32 Value = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Clear the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	/* Update the Kx */
+	Value = (X & 0x0FFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Kx, Value);
+
+	/* Update the Ky */
+	Value = (Y & 0x0FFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Ky, Value);
+
+	/* Update the Kz */
+	Value = (Z & 0x0FFFFFFFul);
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Kz, Value);
+
+	/* Set the register update bit */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL);
+	Value |= XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CONTROL, Value);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the contents of the Mi/An register of BM0.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The contents of the register.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_CipherGetMi(const XHdcp1x *InstancePtr)
+{
+	u64 Mi = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Update Mi */
+	Mi = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Mi_H);
+	Mi <<= 32;
+	Mi |= XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Mi_L);
+
+	return (Mi);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the contents of the Ri register of BM0.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The contents of the register.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XHdcp1x_CipherGetRi(const XHdcp1x *InstancePtr)
+{
+	u16 Ri = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Determine Ri */
+	Ri = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Ri);
+
+	return (Ri);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the contents of the Mo register of the device.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The contents of the Mo register.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_CipherGetMo(const XHdcp1x *InstancePtr)
+{
+	u64 Mo = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Determine Mo */
+	Mo = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Mo_H);
+	Mo <<= 32;
+	Mo |= XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Mo_L);
+
+	return (Mo);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the contents of the Ro register of the device.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The contents of the Ro register.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XHdcp1x_CipherGetRo(const XHdcp1x *InstancePtr)
+{
+	u16 Ro = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check that it is not disabled */
+	if (!XHdcp1x_CipherIsEnabled(InstancePtr)) {
+		return (XST_NOT_ENABLED);
+	}
+
+	/* Determine Ro */
+	Ro = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_CIPHER_Ro);
+
+	return (Ro);
+}
+
+/*****************************************************************************/
+/**
+* This function reads the version of the HDCP cipher core.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	The version of the HDCP cipher device.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdcp1x_CipherGetVersion(const XHdcp1x *InstancePtr)
+{
+	u32 Version = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Version */
+	Version = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_VERSION);
+
+	return (Version);
+}
+
+/*****************************************************************************/
+/**
+ * This function sets the cipher blank value to 0x0000FF (blue),
+ * and sets the cipher blank select to TRUE
+ *
+ * @param	InstancePtr is the device to query.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+ *****************************************************************************/
+void XHdcp1x_CipherEnableBlank(XHdcp1x *InstancePtr)
+{
+	u32 Value = 0;
+
+	/* Verify Arguments */
+	Xil_AssertVoid(InstancePtr);
+
+	/* Set the cipher blank value */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_BLANK_VALUE);
+	Value |= XHDCP1X_CIPHER_BITMASK_BLANK_VALUE;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_BLANK_VALUE, Value);
+
+	/* Enable the cipher blank */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_BLANK_SEL);
+	Value |= XHDCP1X_CIPHER_BITMASK_BLANK_SEL;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_BLANK_SEL, Value);
+}
+
+/*****************************************************************************/
+/**
+ *  This function sets the cipher blank select to FALSE
+ *
+ * @param	InstancePtr is the device to query.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+ *****************************************************************************/
+void XHdcp1x_CipherDisableBlank(XHdcp1x *InstancePtr)
+{
+	u32 Value = 0;
+
+	/* Verify Arguments */
+	Xil_AssertVoid(InstancePtr);
+
+	/* Disable the cipher blank */
+	Value = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_BLANK_SEL);
+	Value &= ~XHDCP1X_CIPHER_BITMASK_BLANK_SEL;
+	XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_BLANK_SEL, Value);
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_cipher.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_cipher.h
@@ -0,0 +1,146 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_cipher.h
+* @{
+*
+* This is the main header file for Xilinx HDCP Cipher core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added macro HDCP1X_CIPHER_BIT_REPEATER_ENABLE
+* 3.1   yas    06/15/16 Added new functions XHdcp1x_CipherEnableBlank
+*                       and XHdcp1x_CipherDisableBlank.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_CIPHER_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_CIPHER_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+#include "xstatus.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+/** @name Handler Types
+* @{
+*/
+/**
+* These constants specify different types of handler and used to differentiate
+* interrupt requests from peripheral.
+*/
+typedef enum {
+	XHDCP1X_CIPHER_HANDLER_LINK_FAILURE = 1,
+	XHDCP1X_CIPHER_HANDLER_Ri_UPDATE,
+} XHdcp1x_CipherHandlerType;
+/*@}*/
+
+
+/** @name Request Types
+* @{
+*/
+/**
+* These constants specify different types of authentication requests that
+* can be initiated within a peripheral
+*/
+typedef enum {
+	XHDCP1X_CIPHER_REQUEST_BLOCK,
+	XHDCP1X_CIPHER_REQUEST_REKEY,
+	XHDCP1X_CIPHER_REQUEST_RNG,
+	XHDCP1X_CIPHER_REQUEST_MAX,
+} XHdcp1x_CipherRequestType;
+/*@}*/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+#define HDCP1X_CIPHER_BIT_REPEATER_ENABLE	(1 << 8) /**< Bit in the cipher
+							   *  Bz register to
+							   *  indicate
+							   *  Repeater */
+
+/************************** Function Prototypes ******************************/
+
+void XHdcp1x_CipherInit(XHdcp1x *InstancePtr);
+
+int XHdcp1x_CipherSetCallback(XHdcp1x *InstancePtr, u32 HandlerType,
+		XHdcp1x_Callback Callback, void *Ref);
+
+int XHdcp1x_CipherSetLinkStateCheck(XHdcp1x *InstancePtr, int IsEnabled);
+int XHdcp1x_CipherIsLinkUp(const XHdcp1x *InstancePtr);
+int XHdcp1x_CipherSetRiUpdate(XHdcp1x *InstancePtr, int IsEnabled);
+
+int XHdcp1x_CipherEnable(XHdcp1x *InstancePtr);
+int XHdcp1x_CipherDisable(XHdcp1x *InstancePtr);
+
+int XHdcp1x_CipherSetKeySelect(XHdcp1x *InstancePtr, u8 KeySelect);
+
+int XHdcp1x_CipherDoRequest(XHdcp1x *InstancePtr,
+		XHdcp1x_CipherRequestType Request);
+int XHdcp1x_CipherIsRequestComplete(const XHdcp1x *InstancePtr);
+
+u32 XHdcp1x_CipherGetNumLanes(const XHdcp1x *InstancePtr);
+int XHdcp1x_CipherSetNumLanes(XHdcp1x *InstancePtr, u32 NumLanes);
+
+u64 XHdcp1x_CipherGetEncryption(const XHdcp1x *InstancePtr);
+int XHdcp1x_CipherEnableEncryption(XHdcp1x *InstancePtr, u64 StreamMap);
+int XHdcp1x_CipherDisableEncryption(XHdcp1x *InstancePtr, u64 StreamMap);
+
+u64 XHdcp1x_CipherGetLocalKsv(const XHdcp1x *InstancePtr);
+u64 XHdcp1x_CipherGetRemoteKsv(const XHdcp1x *InstancePtr);
+int XHdcp1x_CipherSetRemoteKsv(XHdcp1x *InstancePtr, u64 Ksv);
+
+int XHdcp1x_CipherGetB(const XHdcp1x *InstancePtr, u32 *X, u32 *Y, u32 *Z);
+int XHdcp1x_CipherSetB(XHdcp1x *InstancePtr, u32 X, u32 Y, u32 Z);
+int XHdcp1x_CipherGetK(const XHdcp1x *InstancePtr, u32 *X, u32 *Y, u32 *Z);
+int XHdcp1x_CipherSetK(XHdcp1x *InstancePtr, u32 X, u32 Y, u32 Z);
+
+u64 XHdcp1x_CipherGetMi(const XHdcp1x *InstancePtr);
+u16 XHdcp1x_CipherGetRi(const XHdcp1x *InstancePtr);
+u64 XHdcp1x_CipherGetMo(const XHdcp1x *InstancePtr);
+u16 XHdcp1x_CipherGetRo(const XHdcp1x *InstancePtr);
+
+u32 XHdcp1x_CipherGetVersion(const XHdcp1x *InstancePtr);
+
+void XHdcp1x_CipherHandleInterrupt(void *InstancePtr);
+
+void XHdcp1x_CipherEnableBlank(XHdcp1x *InstancePtr);
+void XHdcp1x_CipherDisableBlank(XHdcp1x *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_CIPHER_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_cipher_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_cipher_intr.c
@@ -0,0 +1,263 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_cipher_intr.c
+* @{
+*
+* This file contains interrupt related functions for Xilinx HDCP core.
+* Please see xhdcp1x_cipher.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 4.1   yas    08/03/17 Updated the XHdcp1x_CipherHandleInterrupt function to
+*                       not mask the interrupts, as it is being done in
+*                       hardware now.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x_hw.h"
+#include "xhdcp1x_cipher.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                             Callback Function Type
+* -----------------------------------     -----------------------------------
+* (XHDCP1X_CIPHER_HANDLER_LINK_FAILURE)   LinkFailCallback
+* (XHDCP1X_CIPHER_HANDLER_Ri_UPDATE)      RiUpdateCallback
+* </pre>
+*
+* @param	InstancePtr is a pointer to the HDCP cipher core instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return
+*		- XST_SUCCESS if callback function installed successfully.
+*		- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*		installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetCallback(XHdcp1x *InstancePtr, u32 HandlerType,
+                XHdcp1x_Callback CallbackFunc, void *CallbackRef)
+{
+	u32 Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType >= XHDCP1X_CIPHER_HANDLER_LINK_FAILURE);
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	/* Check for handler type */
+	switch (HandlerType) {
+		/* Link Failure Callback */
+		case (XHDCP1X_CIPHER_HANDLER_LINK_FAILURE):
+			InstancePtr->Cipher.LinkFailCallback = CallbackFunc;
+			InstancePtr->Cipher.LinkFailRef = CallbackRef;
+			InstancePtr->Cipher.IsLinkFailCallbackSet = (TRUE);
+			break;
+
+		/* Ri Update Callback */
+		case (XHDCP1X_CIPHER_HANDLER_Ri_UPDATE):
+			InstancePtr->Cipher.RiUpdateCallback = CallbackFunc;
+			InstancePtr->Cipher.RiUpdateRef = CallbackRef;
+			InstancePtr->Cipher.IsRiUpdateCallbackSet = (TRUE);
+			break;
+
+		default:
+			Status = (XST_INVALID_PARAM);
+			break;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function enables/disables the reporting of link check state changes.
+*
+* @param	InstancePtr is the cipher core instance.
+* @param	IsEnabled enables/disables link state change notifications.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetLinkStateCheck(XHdcp1x *InstancePtr, int IsEnabled)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check DP receive */
+	if (XHdcp1x_IsDP(InstancePtr) && XHdcp1x_IsRX(InstancePtr)) {
+		u32 Val = 0;
+
+		/* Clear any pending link state failure interrupt */
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_STATUS,
+			XHDCP1X_CIPHER_BITMASK_INTERRUPT_LINK_FAIL);
+
+		/* Update it */
+		Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK);
+		if (IsEnabled) {
+			Val &= ~XHDCP1X_CIPHER_BITMASK_INTERRUPT_LINK_FAIL;
+		}
+		else {
+			Val |= XHDCP1X_CIPHER_BITMASK_INTERRUPT_LINK_FAIL;
+		}
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK, Val);
+	}
+	else {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function enables/disables the reporting of Ri update notifications.
+*
+* @param	InstancePtr is the cipher core instance.
+* @param	IsEnabled enables/disables Ri update notifications.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_CipherSetRiUpdate(XHdcp1x *InstancePtr, int IsEnabled)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check HDMI receive */
+	if (XHdcp1x_IsHDMI(InstancePtr)) {
+		u32 Val = 0;
+
+		/* Clear any pending link state failure interrupt */
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_STATUS,
+			XHDCP1X_CIPHER_BITMASK_INTERRUPT_Ri_UPDATE);
+
+		/* Update theDevice */
+		Val = XHdcp1x_ReadReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK);
+		if (IsEnabled) {
+			Val &= ~XHDCP1X_CIPHER_BITMASK_INTERRUPT_Ri_UPDATE;
+		}
+		else {
+			Val |= XHDCP1X_CIPHER_BITMASK_INTERRUPT_Ri_UPDATE;
+		}
+		XHdcp1x_WriteReg(InstancePtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK, Val);
+	}
+	else {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function is the interrupt handler for the cipher core driver.
+*
+* @param	InstancePtr is the cipher core instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_CipherHandleInterrupt(void *InstancePtr)
+{
+	XHdcp1x *HdcpPtr = InstancePtr;
+	u32 Pending = 0;
+
+	/* Verify arguments */
+	Xil_AssertVoid(HdcpPtr != NULL);
+	Xil_AssertVoid(HdcpPtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Determine Pending */
+	Pending = XHdcp1x_ReadReg(HdcpPtr->Config.BaseAddress,
+		XHDCP1X_CIPHER_REG_INTERRUPT_STATUS);
+
+	/* Check for pending */
+	if (Pending != 0) {
+		/* Clear Pending */
+		XHdcp1x_WriteReg(HdcpPtr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_STATUS, Pending);
+
+		/* Update statistics */
+		HdcpPtr->Cipher.Stats.IntCount++;
+
+		/* Check for link integrity failure */
+		if (Pending & XHDCP1X_CIPHER_BITMASK_INTERRUPT_LINK_FAIL) {
+			/* Invoke callback if set */
+			if (HdcpPtr->Cipher.IsLinkFailCallbackSet) {
+				(*HdcpPtr->Cipher.LinkFailCallback)(
+						HdcpPtr->Cipher.LinkFailRef);
+			}
+		}
+
+		/* Check for change to Ri register */
+		if (Pending & XHDCP1X_CIPHER_BITMASK_INTERRUPT_Ri_UPDATE) {
+			/* Invoke callback if set */
+			if (HdcpPtr->Cipher.IsRiUpdateCallbackSet) {
+				(*HdcpPtr->Cipher.RiUpdateCallback)(
+						HdcpPtr->Cipher.RiUpdateRef);
+			}
+		}
+	}
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_debug.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_debug.h
@@ -0,0 +1,70 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_debug.h
+* @{
+*
+* This file provides the interface of the HDCP debug commands
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_DEBUG_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_DEBUG_H
+
+#include "xdebug.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+#define XHDCP1X_DEBUG_LOGMSG if (XHdcp1xDebugLogMsg != NULL) XHdcp1xDebugLogMsg
+ /**< Instance of the function interface used for debug log messages. */
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************* External Declarations *****************************/
+
+extern XHdcp1x_LogMsg XHdcp1xDebugLogMsg;	/**< Instance of function
+						  *  interface used for debug
+						  *  log message statement */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif  /* XHDCP1X_DEBUG_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_hw.h
@@ -0,0 +1,411 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_hw.h
+* @{
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx HDCP cipher core.
+*
+* For more information about the operation of this core see the hardware
+* specification and documentation in the higher level driver xhdcp1x_ciper.h
+* file.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 3.10  yas    06/14/16 Added cipher registers XHDCP1X_CIPHER_REG_BLANK_VALUE
+*                       and XHDCP1X_CIPHER_REG_BLANK_SEL
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_HW_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_HW_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+
+/* HDCP Cipher register offsets */
+#define XHDCP1X_CIPHER_REG_VERSION	(0x0000u)  /**< Version register
+						offset */
+#define XHDCP1X_CIPHER_REG_TYPE		(0x0004u)  /**< Type register offset */
+#define XHDCP1X_CIPHER_REG_SCRATCH	(0x0008u)  /**< Scratch pad register
+						offset */
+#define XHDCP1X_CIPHER_REG_CONTROL	(0x000Cu)  /**< Control register
+						offset */
+#define XHDCP1X_CIPHER_REG_STATUS	(0x0010u)  /**< Status register
+						offset */
+#define XHDCP1X_CIPHER_REG_INTERRUPT_MASK (0x0014u)  /**< Interrupt Mask
+						register offset */
+#define XHDCP1X_CIPHER_REG_INTERRUPT_STATUS \
+					(0x0018u)  /**< Interrupt Status
+						register offset */
+#define XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_H \
+					(0x0020u)  /**< Encryption Enable (High)
+						register offset */
+#define XHDCP1X_CIPHER_REG_ENCRYPT_ENABLE_L \
+					(0x0024u)  /**< Encryption Enable (Low)
+						register offset */
+
+#define XHDCP1X_CIPHER_REG_KEYMGMT_CONTROL \
+					(0x002Cu)  /**< Key Management Control
+						register offset */
+#define XHDCP1X_CIPHER_REG_KEYMGMT_STATUS (0x0030u)  /**< Key Management Status
+						register offset */
+#define XHDCP1X_CIPHER_REG_KSV_LOCAL_H	(0x0038u)  /**< Local KSV (High)
+						register offset */
+#define XHDCP1X_CIPHER_REG_KSV_LOCAL_L	(0x003Cu)  /**< Local KSV (Low) register
+						offset */
+#define XHDCP1X_CIPHER_REG_KSV_REMOTE_H	(0x0040u)  /**< Remote KSV (High)
+						offset */
+#define XHDCP1X_CIPHER_REG_KSV_REMOTE_L	(0x0044u)  /**< Remote KSV (Low)
+						register offset */
+#define XHDCP1X_CIPHER_REG_Km_H		(0x0048u)  /**< Km (High) register
+						offset */
+#define XHDCP1X_CIPHER_REG_Km_L		(0x004Cu)  /**< Km (Low) register
+						offset */
+
+#define XHDCP1X_CIPHER_REG_CIPHER_CONTROL \
+					(0x0050u)  /**< Cipher Control register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_STATUS (0x0054u)  /**< Cipher Status register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Bx	(0x0058u)  /**< Cipher Bx register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_By	(0x005Cu)  /**< Cipher By register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Bz	(0x0060u)  /**< Cipher Bz register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Kx	(0x0064u)  /**< Cipher Kx register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Ky	(0x0068u)  /**< Cipher Ky register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Kz	(0x006Cu)  /**< Cipher Kz register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Mi_H	(0x0070u)  /**< Cipher Mi (High)
+						register offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Mi_L	(0x0074u)  /**< Cipher Mi (Low) register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Ri	(0x0078u)  /**< Cipher Ri register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Ro	(0x007Cu)  /**< Cipher Ro register
+						offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Mo_H	(0x0080u)  /**< Cipher Mo (High)
+						register offset */
+#define XHDCP1X_CIPHER_REG_CIPHER_Mo_L	(0x0084u)  /**< Cipher Mo (Low) register
+						offset */
+#define XHDCP1X_CIPHER_REG_BLANK_VALUE 	(0x00BCu)  /**< Cipher blank value
+						register */
+#define XHDCP1X_CIPHER_REG_BLANK_SEL (0x00C0u)  /**< Cipher blank select
+						register */
+
+/* HDCP Cipher register bit mask definitions */
+#define XHDCP1X_CIPHER_BITMASK_TYPE_PROTOCOL \
+					(0x03u <<  0)	/**< Protocol bitmask in
+						Type register */
+#define XHDCP1X_CIPHER_BITMASK_TYPE_DIRECTION \
+					(0x01u <<  2)  /**< Direction bitmask in
+						Type register */
+
+#define XHDCP1X_CIPHER_BITMASK_CONTROL_ENABLE \
+					(0x01u <<  0)  /**< Enable bitmask in
+						Control register */
+#define XHDCP1X_CIPHER_BITMASK_CONTROL_UPDATE \
+					(0x01u <<  1)  /**< Update bitmask in
+						Control register */
+#define XHDCP1X_CIPHER_BITMASK_CONTROL_NUM_LANES \
+					(0x07u <<  4)  /**< Num Lanes bitmask in
+						Control register */
+#define XHDCP1X_CIPHER_BITMASK_CONTROL_RESET \
+					(0x01u << 31)  /**< Reset bitmask in
+						Control register */
+
+#define XHDCP1X_CIPHER_BITMASK_INTERRUPT_LINK_FAIL \
+					(0x01u <<  0)  /**< Link Failure bitmask
+						in Interrupt register(s) */
+#define XHDCP1X_CIPHER_BITMASK_INTERRUPT_Ri_UPDATE \
+					(0x01u <<  1)  /**< Ri bitmask in
+						Interrupt register(s) */
+
+#define XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_LOCAL_KSV \
+					(0x01u <<  0)  /**< Read Local KSV
+						bitmask in Key Management
+						Control register */
+#define XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_BEGIN_Km \
+					(0x01u <<  1)  /**< Being Km bitmask in
+						Key Management Control
+						register */
+#define XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_ABORT_Km \
+					(0x01u <<  2)  /**< Abort Km bitmask in
+						Key Management Control
+						register */
+#define XHDCP1X_CIPHER_BITMASK_KEYMGMT_CONTROL_SET_SELECT \
+					(0x07u << 16)  /**< Key Set Select
+						bitmask in Key Management
+						Control register */
+
+#define XHDCP1X_CIPHER_BITMASK_KEYMGMT_STATUS_KSV_READY \
+					(0x01u <<  0)  /**< Local KSV ready
+						bitmask in Key Management Status
+						register */
+#define XHDCP1X_CIPHER_BITMASK_KEYMGMT_STATUS_Km_READY \
+					(0x01u <<  1)  /**< Km Value ready
+						bitmask in Key Management Status
+						register */
+
+#define XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_XOR_ENABLE \
+					(0x01u <<  0)  /**< XOR Enable bitmask
+						in Cipher Control register */
+#define XHDCP1X_CIPHER_BITMASK_CIPHER_CONTROL_REQUEST \
+					(0x07u <<  8)  /**< Request bitmask in
+						Cipher Control register */
+
+#define XHDCP1X_CIPHER_BITMASK_CIPHER_STATUS_XOR_IN_PROG \
+					(0x01u <<  0)  /**< XOR In Progress
+						bitmask in Cipher Status
+						register */
+#define XHDCP1X_CIPHER_BITMASK_CIPHER_STATUS_REQUEST_IN_PROG \
+					(0x07u <<  8)  /**< Request In Progress
+						bitmask in Cipher Status
+						register */
+
+#define XHDCP1X_CIPHER_BITMASK_BLANK_VALUE \
+					(0x000000FF) /**< Cipher blank value
+					bitmask, lower 24 bits */
+#define XHDCP1X_CIPHER_BITMASK_BLANK_SEL \
+					(0x1u)  /**< Cipher blank
+						select bitmask */
+
+/* HDCP Cipher register bit value definitions */
+#define XHDCP1X_CIPHER_VALUE_TYPE_PROTOCOL_DP \
+					(0x00u <<  0)  /**< DP Protocol value in
+						Type register */
+#define XHDCP1X_CIPHER_VALUE_TYPE_PROTOCOL_HDMI \
+					(0x01u <<  0)  /**< HDMI Protocol value
+						in Type register */
+
+#define XHDCP1X_CIPHER_VALUE_TYPE_DIRECTION_RX \
+					(0x00u <<  2)  /**< RX Direction value
+						in Type register */
+#define XHDCP1X_CIPHER_VALUE_TYPE_DIRECTION_TX \
+					(0x01u <<  2)  /**< TX Direction value
+						in Type register */
+
+#define XHDCP1X_CIPHER_VALUE_CIPHER_CONTROL_REQUEST_BLOCK \
+					(0x01u <<  8)  /**< Block Request value
+						in Cipher Control register */
+#define XHDCP1X_CIPHER_VALUE_CIPHER_CONTROL_REQUEST_REKEY \
+					(0x01u <<  9)  /**< ReKey Request value
+						in Cipher Control register */
+#define XHDCP1X_CIPHER_VALUE_CIPHER_CONTROL_REQUEST_RNG \
+					(0x01u << 10)  /**< RNG Request value in
+						Cipher Control register */
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/* Register access macro definition */
+#define XHdcp1x_In32		Xil_In32	/**< Input Operations */
+#define XHdcp1x_Out32		Xil_Out32	/**< Output Operations */
+
+/*****************************************************************************/
+/**
+*
+* This macro reads a value from a HDCP cipher register. A 32 bit read is
+* always performed.
+*
+* @param  BaseAddress is the base address of the HDCP cipher core instance.
+* @param  RegOffset is the register offset of the register
+*
+* @return
+*  The 32-bit value of the register.
+*
+* @note
+* C-style: u32 XHdcp1x_ReadReg(UINTPTR BaseAddress, u32 RegOffset)
+*
+******************************************************************************/
+#define XHdcp1x_ReadReg(BaseAddress, RegOffset) \
+	XHdcp1x_In32((BaseAddress) + ((u32)RegOffset))
+
+/*****************************************************************************/
+/**
+*
+* This macro writes a value to a HDCP cipher register. A 32 bit write is
+* always performed.
+*
+* @param  BaseAddress is the base address of the HDCP cipher core instance.
+* @param  RegOffset is the register offset of the register
+* @param  Data is the 32-bit value to write into the register.
+*
+* @return
+*  None.
+*
+* @note
+* C-style: void XHdcp1x_WriteReg(UINTPTR BaseAddress, u32 RegOffset, u32 Data)
+*
+******************************************************************************/
+#define XHdcp1x_WriteReg(BaseAddress, RegOffset, Data) \
+	XHdcp1x_Out32((BaseAddress) + ((u32)RegOffset), (u32)(Data))
+
+/*****************************************************************************/
+/**
+* This queries a cipher to determine if it is enabled.
+*
+* @param	InstancePtr is the instance to query.
+*
+* @return	Truth value indicating transmitter (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHdcp1x_CipherIsEnabled(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_CONTROL) & \
+	XHDCP1X_CIPHER_BITMASK_CONTROL_ENABLE) != 0)
+
+/*****************************************************************************/
+/**
+* This queries a cipher to determine if the XOR (encryption) function is
+* currently in progress.
+*
+* @param	InstancePtr is the instance to query.
+*
+* @return	Truth value indicating in progress (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHdcp1x_CipherXorInProgress(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_CIPHER_STATUS) & \
+	XHDCP1X_CIPHER_BITMASK_CIPHER_STATUS_XOR_IN_PROG) != 0)
+
+/*****************************************************************************/
+/**
+* This queries a cipher to determine if the local KSV is ready to read.
+*
+* @param	InstancePtr is the instance to query.
+*
+* @return	Truth value indicating ready (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHdcp1x_CipherLocalKsvReady(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_KEYMGMT_STATUS) & \
+	XHDCP1X_CIPHER_BITMASK_KEYMGMT_STATUS_KSV_READY) != 0)
+
+/*****************************************************************************/
+/**
+* This queries a cipher to determine if the Km value is ready.
+*
+* @param	InstancePtr is the instance to query.
+*
+* @return	Truth value indicating ready (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHdcp1x_CipherKmReady(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_KEYMGMT_STATUS) & \
+	XHDCP1X_CIPHER_BITMASK_KEYMGMT_STATUS_Km_READY) != 0)
+
+/*****************************************************************************/
+/**
+*
+* This macro checks if a core supports the Display Port protocol
+*
+* @param	InstancePtr is a pointer to the XHdcp1x core instance.
+*
+* @return	Truth value indicating DP (TRUE) or not (FALSE)
+*
+******************************************************************************/
+#define XHdcp1x_IsDP(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_TYPE) & XHDCP1X_CIPHER_BITMASK_TYPE_PROTOCOL) \
+	== XHDCP1X_CIPHER_VALUE_TYPE_PROTOCOL_DP)
+
+/*****************************************************************************/
+/**
+*
+* This macro checks if a core supports the HDMI protocol
+*
+* @param	InstancePtr is a pointer to the XHdcp1x core instance.
+*
+* @return	Truth value indicating HDMI (TRUE) or not (FALSE)
+*
+******************************************************************************/
+#define XHdcp1x_IsHDMI(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_TYPE) & XHDCP1X_CIPHER_BITMASK_TYPE_PROTOCOL) \
+	== XHDCP1X_CIPHER_VALUE_TYPE_PROTOCOL_HDMI)
+
+/*****************************************************************************/
+/**
+*
+* This macro checks if a core supports the receive direction
+*
+* @param	InstancePtr is a pointer to the XHdcp1x core instance.
+*
+* @return	Truth value indicating receive (TRUE) or not (FALSE)
+*
+******************************************************************************/
+#define XHdcp1x_IsRX(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_TYPE) & XHDCP1X_CIPHER_BITMASK_TYPE_DIRECTION) \
+	== XHDCP1X_CIPHER_VALUE_TYPE_DIRECTION_RX)
+
+/*****************************************************************************/
+/**
+*
+* This macro checks if a core supports the transmit direction
+*
+* @param	InstancePtr is a pointer to the XHdcp1x core instance.
+*
+* @return	Truth value indicating transmit (TRUE) or not (FALSE)
+*
+******************************************************************************/
+#define XHdcp1x_IsTX(InstancePtr) \
+	((XHdcp1x_ReadReg((InstancePtr)->Config.BaseAddress, \
+	XHDCP1X_CIPHER_REG_TYPE) & XHDCP1X_CIPHER_BITMASK_TYPE_DIRECTION) \
+	== XHDCP1X_CIPHER_VALUE_TYPE_DIRECTION_TX)
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_HW_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_intr.c
@@ -0,0 +1,149 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_cipher_intr.c
+* @{
+*
+* This file contains interrupt related functions for Xilinx HDCP core.
+* Please see xhdcp_cipher.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 3.0   yas    02/13/16 Added function XHdcp1x_SetCallBack.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+#include "xhdcp1x_port.h"
+#include "xil_types.h"
+#include "xhdcp1x_tx.h"
+#include "xhdcp1x_rx.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function installs callback functions for the given HandlerType.
+*
+* @param	InstancePtr is a pointer to the HDCP core instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return
+*		- XST_SUCCESS if callback function installed successfully.
+*		- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*		installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp1x_SetCallback(XHdcp1x *InstancePtr, XHdcp1x_HandlerType HandlerType,
+		void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType > (XHDCP1X_HANDLER_UNDEFINED));
+	Xil_AssertNonvoid(HandlerType < (XHDCP1X_HANDLER_INVALID));
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	u32 Status;
+
+	/* Check for TX */
+	if (!InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_TxSetCallback(InstancePtr, HandlerType,
+			CallbackFunc, CallbackRef);
+	}
+	/* Check for RX */
+	else if (InstancePtr->Config.IsRx) {
+		Status = XHdcp1x_RxSetCallback(InstancePtr, HandlerType,
+			CallbackFunc, CallbackRef);
+	}
+	else {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function is the cipher interrupt handler for the HDCP module.
+*
+* @param	InstancePtr is the device instance that just interrupted.
+*
+* @return	None.
+*
+* @note		This function just forwards the interrupt along to the
+*		corresponding cipher core.
+*
+******************************************************************************/
+void XHdcp1x_CipherIntrHandler(void *InstancePtr)
+{
+	XHdcp1x *HdcpPtr = InstancePtr;
+
+	/* Verify arguments */
+	Xil_AssertVoid(HdcpPtr != NULL);
+	Xil_AssertVoid(HdcpPtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Dispatch it to the corresponding cipher */
+	XHdcp1x_CipherHandleInterrupt(HdcpPtr);
+}
+
+/*****************************************************************************/
+/**
+* This function is the port interrupt handler for the HDCP module.
+*
+* @param	InstancePtr is the device instance that just interrupted.
+* @param	IntCause is the interrupt cause bit map.
+*
+* @return	None.
+*
+* @note		This function just forwards the interrupt along to the
+*		corresponding cipher core.
+*
+******************************************************************************/
+void XHdcp1x_PortIntrHandler(void *InstancePtr, u32 IntCause)
+{
+	XHdcp1x *HdcpPtr = InstancePtr;
+
+	/* Verify arguments */
+	Xil_AssertVoid(HdcpPtr != NULL);
+	Xil_AssertVoid(HdcpPtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Dispatch it to the corresponding port */
+	XHdcp1x_PortHandleInterrupt(HdcpPtr, IntCause);
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_platform.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_platform.c
@@ -0,0 +1,172 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_platform.c
+* @{
+*
+* This file provides the implementation for the hdcp platform integration
+* module
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+#include "xhdcp1x_platform.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Extern Declarations ******************************/
+
+extern XHdcp1x_KsvRevokeCheck XHdcp1xKsvRevokeCheck; /**< Instance of function
+						       *  interface used for
+						       *  checking a specific
+						       *  KSV against the
+						       *  platforms revocation
+						       *  list */
+
+/************************** Function Prototypes ******************************/
+
+/*****************************************************************************/
+/**
+* This function checks a KSV value to determine if it has been revoked or not.
+*
+* @param	InstancePtr is the HDCP interface.
+* @param	Ksv is the KSV to check.
+*
+* @return	Truth value indicating the KSV is revoked (TRUE) or not (FALSE)
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PlatformIsKsvRevoked(const XHdcp1x *InstancePtr, u64 Ksv)
+{
+	int IsRevoked = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Sanity Check */
+	if (XHdcp1xKsvRevokeCheck != NULL) {
+		IsRevoked = (*XHdcp1xKsvRevokeCheck)(InstancePtr, Ksv);
+	}
+
+	return (IsRevoked);
+}
+
+/*****************************************************************************/
+/**
+* This function starts a timer on behalf of an HDCP interface.
+*
+* @param	InstancePtr is the hdcp interface.
+* @param	TimeoutInMs is the duration of the timer in milliseconds.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PlatformTimerStart(XHdcp1x *InstancePtr, u16 TimeoutInMs)
+{
+	int Status = XST_SUCCESS;
+
+	/* Sanity Check */
+	if (InstancePtr->XHdcp1xTimerStart != NULL) {
+	Status = (*(InstancePtr->XHdcp1xTimerStart))((void *)InstancePtr,
+			TimeoutInMs);
+	}
+	else {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function stop a timer on behalf of an HDCP interface.
+*
+* @param	InstancePtr is the HDCP interface.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PlatformTimerStop(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Sanity Check */
+	if (InstancePtr->XHdcp1xTimerStop != NULL) {
+	Status = (*(InstancePtr->XHdcp1xTimerStop))((void *)InstancePtr);
+	}
+	else {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function busy waits on a timer for a number of milliseconds.
+*
+* @param	InstancePtr is the hdcp interface.
+* @param	DelayInMs is the delay time in milliseconds.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PlatformTimerBusy(XHdcp1x *InstancePtr, u16 DelayInMs)
+{
+	int Status = XST_SUCCESS;
+
+	/* Sanity Check */
+	if (InstancePtr->XHdcp1xTimerDelay != NULL) {
+	Status = (*(InstancePtr->XHdcp1xTimerDelay))((void *)InstancePtr,
+			DelayInMs);
+	}
+	else {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_platform.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_platform.h
@@ -0,0 +1,65 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_platform.h
+* @{
+*
+* This file provides the interface for the hdcp platform integration module
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_PLATFORM_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_PLATFORM_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+int XHdcp1x_PlatformIsKsvRevoked(const XHdcp1x *InstancePtr, u64 Ksv);
+int XHdcp1x_PlatformTimerStart(XHdcp1x *InstancePtr, u16 TimeoutInMs);
+int XHdcp1x_PlatformTimerStop(XHdcp1x *InstancePtr);
+int XHdcp1x_PlatformTimerBusy(XHdcp1x *InstancePtr, u16 DelayInMs);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif  /* XHDCP1X_PLATFORM_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port.c
@@ -0,0 +1,422 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_port.c
+* @{
+*
+* This contains the main implementation file for the Xilinx HDCP Port driver
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 3.10  yas    07/28/16 Added fucntion XHdcp1x_PortSetRepeater
+* </pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files *********************************/
+
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x_port.h"
+#include "xil_assert.h"
+#include "xil_types.h"
+
+
+/************************** Constant Definitions *****************************/
+#if defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+    (XPAR_XV_HDMITX1_NUM_INSTANCES > 0)
+#define INCLUDE_HDMI_TX
+#endif
+#if defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+    (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0)
+#define INCLUDE_HDMI_RX
+#endif
+#if defined(XPAR_XV_HDMITX_NUM_INSTANCES) && (XPAR_XV_HDMITX_NUM_INSTANCES > 0)
+#define INCLUDE_HDMI_TX
+#endif
+#if defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)
+#define INCLUDE_HDMI_RX
+#endif
+#if defined(XPAR_XDPRXSS_NUM_INSTANCES) && (XPAR_XDPRXSS_NUM_INSTANCES > 0)
+#define INCLUDE_DP_RX
+#endif
+#if defined(XPAR_XDPTXSS_NUM_INSTANCES) && (XPAR_XDPTXSS_NUM_INSTANCES > 0)
+#define INCLUDE_DP_TX
+#endif
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Extern Declarations ******************************/
+
+#if defined(INCLUDE_HDMI_TX)
+extern const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortHdmiTxAdaptor;
+#endif
+#if defined(INCLUDE_HDMI_RX)
+extern const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortHdmiRxAdaptor;
+#endif
+#if defined(INCLUDE_DP_TX)
+extern const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortDpTxAdaptor;
+#endif
+#if defined(INCLUDE_DP_RX)
+extern const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortDpRxAdaptor;
+#endif
+
+/*************************** Function Prototypes *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function determines the adaptor for a specified port device.
+*
+* @param	InstancePtr is the device whose adaptor is to be determined.
+*
+* @return	A pointer to the adaptor table. NULL if not found.
+*
+* @note		None.
+*
+******************************************************************************/
+const XHdcp1x_PortPhyIfAdaptor *XHdcp1x_PortDetermineAdaptor(
+		XHdcp1x *InstancePtr)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	XHdcp1x_Config *CfgPtr = &InstancePtr->Config;
+
+#if defined(INCLUDE_HDMI_RX)
+	/* Check for HDMI Rx */
+	if ((CfgPtr->IsRx) && (CfgPtr->IsHDMI)) {
+		Adaptor = &XHdcp1x_PortHdmiRxAdaptor;
+	}
+	else
+#endif
+#if defined(INCLUDE_HDMI_TX)
+	/* Check for HDMI Tx */
+	if (!(CfgPtr->IsRx) && (CfgPtr->IsHDMI)) {
+		Adaptor = &XHdcp1x_PortHdmiTxAdaptor;
+	}
+	else
+#endif
+#if defined(INCLUDE_DP_RX)
+	/* Check for DP Rx */
+	if ((CfgPtr->IsRx) && !(CfgPtr->IsHDMI)) {
+		Adaptor = &XHdcp1x_PortDpRxAdaptor;
+	}
+	else
+#endif
+#if defined(INCLUDE_DP_TX)
+	/* Check for DP Tx */
+	if (!(CfgPtr->IsRx) && !(CfgPtr->IsHDMI)) {
+		Adaptor = &XHdcp1x_PortDpTxAdaptor;
+	}
+	else
+#endif
+	{
+		Adaptor = NULL;
+	}
+
+	return (Adaptor);
+}
+
+/*****************************************************************************/
+/**
+* This function enables a port device.
+*
+* @param	InstancePtr is the device to enables.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NO_FEATURE if the port lacks an Enable function.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortEnable(XHdcp1x *InstancePtr)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Sanity Check */
+	if (Adaptor == NULL) {
+		Status = XST_NO_FEATURE;
+	}
+	/* Invoke adaptor function if present */
+	else if (Adaptor->Enable != NULL) {
+		Status = (*(Adaptor->Enable))(InstancePtr);
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables a port device.
+*
+* @param	InstancePtr is the device to disables.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NO_FEATURE if the port lacks a Disable function.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortDisable(XHdcp1x *InstancePtr)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Sanity Check */
+	if (Adaptor == NULL) {
+		Status = XST_NO_FEATURE;
+	}
+	/* Invoke adaptor function if present */
+	else if (Adaptor->Disable != NULL) {
+		Status = (*(Adaptor->Disable))(InstancePtr);
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function queries a port device to determine if hdcp is supported.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	Truth value.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortIsCapable(const XHdcp1x *InstancePtr)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int IsCapable = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Invoke adaptor function if present */
+	if ((Adaptor != NULL) && (Adaptor->IsCapable != NULL)) {
+		IsCapable = (*(Adaptor->IsCapable))(InstancePtr);
+	}
+
+	return (IsCapable);
+}
+
+/*****************************************************************************/
+/**
+* This function queries a port device to determine if it is connected to a
+* repeater.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	Truth value.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortIsRepeater(const XHdcp1x *InstancePtr)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int IsRepeater = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Invoke adaptor function if present */
+	if ((Adaptor != NULL) && (Adaptor->IsRepeater != NULL)) {
+		IsRepeater = (*(Adaptor->IsRepeater))(InstancePtr);
+	}
+
+	return (IsRepeater);
+}
+
+/*****************************************************************************/
+/**
+* This function set the REPEATER information in the connected device.
+*
+* @param	InstancePtr is the device to query.
+* @param	RptrConf is the configuration of the device as repeater.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NO_FEATURE if the port fails to set the Repeater value.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortSetRepeater(XHdcp1x *InstancePtr, u8 RptrConf)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Sanity Check */
+	if (Adaptor == NULL) {
+		Status = XST_NO_FEATURE;
+	}
+	/* Invoke adaptor function if present */
+	else if (Adaptor->SetRepeater != NULL) {
+		Status = (*(Adaptor->SetRepeater))(InstancePtr, RptrConf);
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the repeater information from the connected device.
+*
+* @param	InstancePtr is the device to query.
+* @param	InfoPtr is the repeater info.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_NO_FEATURE if the port lacks a GetRepeaterInfo function.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortGetRepeaterInfo(XHdcp1x *InstancePtr, u16 *InfoPtr)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InfoPtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Sanity Check */
+	if (Adaptor == NULL) {
+		Status = XST_NO_FEATURE;
+	}
+	/* Invoke adaptor function if present */
+	else if (Adaptor->GetRepeaterInfo != NULL) {
+		Status = (*(Adaptor->GetRepeaterInfo))(InstancePtr, InfoPtr);
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function reads a register from a HDCP port device.
+*
+* @param	InstancePtr is the device to read from.
+* @param	Offset is the offset to start reading from.
+* @param	Buf is the buffer to copy the data read.
+* @param	BufSize is the size of the buffer.
+*
+* @return	The number of bytes read.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortRead(const XHdcp1x *InstancePtr, u8 Offset, void *Buf,
+                u32 BufSize)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int NumRead = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Buf != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Invoke adaptor function if present */
+	if ((Adaptor != NULL) && (Adaptor->Read != NULL)) {
+		NumRead = (*(Adaptor->Read))(InstancePtr, Offset, Buf,
+				BufSize);
+	}
+
+	return (NumRead);
+}
+
+/*****************************************************************************/
+/**
+* This function writes a register within a HDCP port device.
+*
+* @param	InstancePtr is the device to write to.
+* @param	Offset is the offset to start writing at.
+* @param	Buf is the buffer containing the data to write.
+* @param	BufSize is the size of the buffer.
+*
+* @return	The number of bytes written.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_PortWrite(XHdcp1x *InstancePtr, u8 Offset, const void *Buf,
+                u32 BufSize)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+	int NumWritten = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Buf != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Invoke adaptor function if present */
+	if ((Adaptor != NULL) && (Adaptor->Write != NULL)) {
+		NumWritten = (*(Adaptor->Write))(InstancePtr, Offset, Buf,
+		                BufSize);
+	}
+
+	return (NumWritten);
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port.h
@@ -0,0 +1,204 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/**
+*
+* @file xhdcp1x_port.h
+* @{
+*
+* This header file contains the external declarations associated with the
+* HDCP port driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 2.00  MG     01/20/16 Added callback handler to XHdcp1x_PortPhyIfAdaptor
+* 3.10  yas    07/28/16 Added callback handler SetRepeater to
+*                       XHdcp1x_PortPhyIfAdaptor
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_PORT_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_PORT_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+
+#include "xstatus.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * This typedef defines the different types of handlers that can be registered
+ * to service interrupt requests from the HDCP port instance
+ */
+typedef enum {
+	XHDCP1X_PORT_HANDLER_AUTHENTICATE = 1, /**< An (re)auth request */
+} XHdcp1x_PortHandlerType;
+
+/**
+ * The typedef defines the HDCP port adaptor table.  This contains a series of
+ * functions that map the external interface of the HDCP port device to the
+ * underlying physical interface that it is running over
+ */
+typedef struct XHdcp1x_PortPhyIfAdaptorS {
+	int (*Init)(XHdcp1x *);			/**< Initialization function */
+	int (*Enable)(XHdcp1x *);		/**< Enable function */
+	int (*Disable)(XHdcp1x *);		/**< Disable function */
+	int (*Read)(const XHdcp1x *, u8, void *, u32); /**< Reg read */
+	int (*Write)(XHdcp1x *, u8, const void *, u32); /**< Reg write */
+	int (*IsCapable)(const XHdcp1x *);	/**< Tests for HDCP capable */
+	int (*IsRepeater)(const XHdcp1x *);	/**< Tests for repeater */
+	int (*SetRepeater)(XHdcp1x *, u8);	/**< Sets repeater */
+	int (*GetRepeaterInfo)(const XHdcp1x *, u16 *); /**< Gets repeater
+							  *  info */
+	void (*IntrHandler)(XHdcp1x *, u32); /**< Interrupt handler */
+	void (*CallbackHandler)(void *CallbackRef); /**< Callback handler */
+} XHdcp1x_PortPhyIfAdaptor;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+* This macro converts from an unsigned integer to a little endian formatted
+* buffer
+*
+* @param	buf the buffer to write to
+* @param	uint the unsigned integer to convert
+* @param	numbits the number of bits within the unsigned integer to use
+*
+* @return	None.
+*
+* @note		The value of the "uint" parameter is destroyed by a call to this
+*		macro
+*
+******************************************************************************/
+#define XHDCP1X_PORT_UINT_TO_BUF(buf, uint, numbits)			\
+	if ((numbits) > 0) {						\
+		int byte;						\
+		for (byte = 0; byte <= (int)(((numbits) - 1) >> 3); byte++) { \
+			buf[byte] = (uint8_t) (uint & 0xFFu);		\
+			uint >>= 8;					\
+		}							\
+	}
+
+/*****************************************************************************/
+/**
+* This macro converts from a little endian formatted buffer to an unsigned
+* integer value
+*
+* @param	uint the unsigned integer to write
+* @param	buf the buffer to convert
+* @param	numbits the number of bits within the buffer to use
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHDCP1X_PORT_BUF_TO_UINT(uint, buf, numbits)			\
+	if ((numbits) > 0) {						\
+		int byte;						\
+		uint = 0;	 					\
+		for (byte = (((numbits) - 1) >> 3); byte >= 0; byte--) { \
+			uint <<= 8;					\
+			uint  |= buf[byte];				\
+		}							\
+	}
+
+/*****************************************************************************/
+/**
+* This macro sets a bit within a little endian formatted buffer
+*
+* @param	buf the buffer to write to
+* @param	bitnum the bit to set
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHDCP1X_PORT_BSET_IN_BUF(buf, bitnum)	\
+	buf[(bitnum) >> 3] |=  (1u << ((bitnum) & 0x07u));
+
+/*****************************************************************************/
+/**
+* This macro clears a bit within a little endian formatted buffer
+*
+* @param	buf the buffer to write to
+* @param	bitnum the bit to clear
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHDCP1X_PORT_BCLR_IN_BUF(buf, bitnum)	\
+	buf[(bitnum) >> 3] &= ~(1u << ((bitnum) & 0x07u));
+
+/*****************************************************************************/
+/**
+* This macro tests a bit within a little endian formatted buffer
+*
+* @param	buf the buffer containing the bit to test
+* @param	bitnum the bit to test
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+#define XHDCP1X_PORT_BTST_IN_BUF(buf, bitnum)	\
+	(buf[(bitnum) >> 3] & (1u << ((bitnum) & 0x07u)))
+
+/************************** Function Prototypes ******************************/
+
+const XHdcp1x_PortPhyIfAdaptor *XHdcp1x_PortDetermineAdaptor(
+		XHdcp1x *InstancePtr);
+int XHdcp1x_PortSetCallback(XHdcp1x *InstancePtr, u32 HandlerType,
+	XHdcp1x_Callback Callback, void *Parameter);
+
+int XHdcp1x_PortEnable(XHdcp1x *InstancePtr);
+int XHdcp1x_PortDisable(XHdcp1x *InstancePtr);
+int XHdcp1x_PortIsCapable(const XHdcp1x *InstancePtr);
+int XHdcp1x_PortIsRepeater(const XHdcp1x *InstancePtr);
+int XHdcp1x_PortSetRepeater(XHdcp1x *InstancePtr, u8 RptrConf);
+int XHdcp1x_PortGetRepeaterInfo(XHdcp1x *InstancePtr, u16 *Info);
+int XHdcp1x_PortRead(const XHdcp1x *InstancePtr, u8 Offset, void *Buf,
+	u32 BufSize);
+int XHdcp1x_PortWrite(XHdcp1x *InstancePtr, u8 Offset, const void *Buf,
+	u32 BufSize);
+
+void XHdcp1x_PortHandleInterrupt(XHdcp1x *InstancePtr, u32 IntCause);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_PORT_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_hdmi.h
@@ -0,0 +1,149 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_port_hdmi.h
+* @{
+*
+* This file contains the definitions for the hdcp port registers/offsets for
+* HDMI interfaces
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 3.1   yas    07/28/16 Added Bitmasks for BSTATUS register.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_PORT_HDMI_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_PORT_HDMI_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#if defined(XHDCP1X_PORT_DP_H)
+#error "cannot include both xhdcp1x_port_dp.h and xhdcp1x_port_hdmi.h"
+#endif
+
+/************************** Constant Definitions *****************************/
+
+/**
+ * These constants specify the offsets for the various fields and/or
+ * attributes within the hdcp port
+ */
+#define XHDCP1X_PORT_OFFSET_BKSV	(0x00u)   /**< Bksv Offset        */
+#define XHDCP1X_PORT_OFFSET_RO		(0x08u)   /**< Ri'/Ro' Offset     */
+#define XHDCP1X_PORT_OFFSET_PJ		(0x0Au)   /**< Pj' Offset         */
+#define XHDCP1X_PORT_OFFSET_AKSV	(0x10u)   /**< Aksv Offset        */
+#define XHDCP1X_PORT_OFFSET_AINFO	(0x15u)   /**< Ainfo Offset       */
+#define XHDCP1X_PORT_OFFSET_AN		(0x18u)   /**< An Offset          */
+#define XHDCP1X_PORT_OFFSET_VH0		(0x20u)   /**< V'.H0 Offset       */
+#define XHDCP1X_PORT_OFFSET_VH1		(0x24u)   /**< V'.H1 Offset       */
+#define XHDCP1X_PORT_OFFSET_VH2		(0x28u)   /**< V'.H2 Offset       */
+#define XHDCP1X_PORT_OFFSET_VH3		(0x2Cu)   /**< V'.H3 Offset       */
+#define XHDCP1X_PORT_OFFSET_VH4		(0x30u)   /**< V'.H4 Offset       */
+#define XHDCP1X_PORT_OFFSET_BCAPS	(0x40u)   /**< Bcaps Offset       */
+#define XHDCP1X_PORT_OFFSET_BSTATUS	(0x41u)   /**< Bstatus Offset     */
+#define XHDCP1X_PORT_OFFSET_KSVFIFO	(0x43u)   /**< KSV FIFO Offset    */
+#define XHDCP1X_PORT_OFFSET_DBG		(0xC0u)   /**< Debug Space Offset */
+
+/**
+ * These constants specify the sizes for the various fields and/or
+ * attributes within the hdcp port
+ */
+#define XHDCP1X_PORT_SIZE_BKSV		(0x05u)   /**< Bksv Size          */
+#define XHDCP1X_PORT_SIZE_RO		(0x02u)   /**< Ri' Size           */
+#define XHDCP1X_PORT_SIZE_PJ		(0x01u)   /**< Pj' Size           */
+#define XHDCP1X_PORT_SIZE_AKSV		(0x05u)   /**< Aksv Size          */
+#define XHDCP1X_PORT_SIZE_AINFO		(0x01u)   /**< Ainfo Size         */
+#define XHDCP1X_PORT_SIZE_AN		(0x08u)   /**< An Size            */
+#define XHDCP1X_PORT_SIZE_VH0		(0x04u)   /**< V'.H0 Size         */
+#define XHDCP1X_PORT_SIZE_VH1		(0x04u)   /**< V'.H1 Size         */
+#define XHDCP1X_PORT_SIZE_VH2		(0x04u)   /**< V'.H2 Size         */
+#define XHDCP1X_PORT_SIZE_VH3		(0x04u)   /**< V'.H3 Size         */
+#define XHDCP1X_PORT_SIZE_VH4		(0x04u)   /**< V'.H4 Size         */
+#define XHDCP1X_PORT_SIZE_BCAPS		(0x01u)   /**< Bcaps Size         */
+#define XHDCP1X_PORT_SIZE_BSTATUS	(0x02u)   /**< Bstatus Size       */
+#define XHDCP1X_PORT_SIZE_KSVFIFO	(0x01u)   /**< KSV FIFO Size      */
+#define XHDCP1X_PORT_SIZE_DBG		(0xC0u)   /**< Debug Space Size   */
+
+/**
+ * These constants specify the bit definitions within the various fields
+ * and/or attributes within the hdcp port
+ */
+#define XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE  (1u << 12) /**< BStatus HDMI Mode
+							 *  Mask */
+#define XHDCP1X_PORT_BIT_BCAPS_FAST_REAUTH  (1u <<  0) /**< BCaps Fast Reauth
+							 *  Mask */
+#define XHDCP1X_PORT_BIT_BCAPS_1d1_FEATURES (1u <<  1) /**< BCaps HDCP 1.1
+							 *  Features Support
+							 *  Mask */
+#define XHDCP1X_PORT_BIT_BCAPS_FAST	    (1u <<  4) /**< BCaps Fast
+							 *  Transfers Mask */
+#define XHDCP1X_PORT_BIT_BCAPS_READY	    (1u <<  5) /**< BCaps KSV FIFO
+							 *  Ready bit Mask */
+#define XHDCP1X_PORT_BIT_BCAPS_REPEATER	    (1u <<  6) /**< BCaps Repeater
+							 *  Capable Mask */
+#define XHDCP1X_PORT_BIT_BCAPS_HDMI	    (1u <<  7) /**< BCaps HDMI
+							 *  Supported Mask */
+#define XHDCP1X_PORT_BIT_AINFO_ENABLE_1d1_FEATURES (1u <<  1) /**< AInfo Enable
+								*  1.1
+								*  Features */
+
+#define XHDCP1X_PORT_BSTATUS_BIT_DEV_CNT_ERR	(1u << 7) /**< BStatus Device
+							 *  Count Error Mask */
+#define XHDCP1X_PORT_BSTATUS_BIT_DEV_CNT_NO_ERR	(0u << 7) /**< BStatus Device
+						  *  Count for No Error Mask */
+#define XHDCP1X_PORT_BSTATUS_DEV_CNT_MASK		(0x7F) /**< BStatus
+						  *  Device Count Error Mask */
+#define XHDCP1X_PORT_BSTATUS_BIT_DEPTH_ERR		(1u << 11) /**< BStatus
+							  * Depth Error Mask */
+#define XHDCP1X_PORT_BSTATUS_BIT_DEPTH_NO_ERR	(0u << 11) /**< BStatus Depth
+						  *  Error for No Error Mask */
+#define XHDCP1X_PORT_BSTATUS_DEV_CNT_ERR_SHIFT	(7) /**< BStatus Device
+						    *  Count Error Shift Mask*/
+#define XHDCP1X_PORT_BSTATUS_DEPTH_ERR_SHIFT	(11) /**< BStatus Depth
+							  *  Error Shift Mask*/
+#define XHDCP1X_PORT_BSTATUS_DEPTH_SHIFT		(8) /**< BStatus Device
+							 *  Count Error Mask */
+
+/**
+ * This constant defines the i2c address of the hdcp port
+ */
+#define XHDCP1X_PORT_PRIMARY_I2C_ADDR	(0x74u)  /**< I2C Addr Primary Link  */
+#define XHDCP1X_PORT_SECONDARY_I2C_ADDR	(0x76u)  /**< I2C Addr Secondary Link*/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Prototypes ******************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_PORT_HDMI_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_hdmi_rx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_hdmi_rx.c
@@ -0,0 +1,406 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_port_hdmi_rx.c
+* @{
+*
+* This contains the implementation of the HDCP port driver for HDMI RX
+* interfaces
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 2.00  MG     01/20/16 Disabled hdcp call back in function
+*                       XHdcp1x_PortHdmiRxEnable.
+* 2.10  MG     02/29/16 Added DDC write and read handlers
+* 3.0   yas    02/13/16 Upgraded function XHdcp1x_PortHdmiRxEnable to
+*                       support HDCP Repeater functionality.
+* 3.1   yas    07/28/16 Added function XHdcp1x_PortHdmiRxSetRepeater
+* 3.2   yas    10/27/16 Updated the XHdcp1x_PortHdmiRxDisable function to not
+*                       clear the AKSV, An and AInfo values in the DDC space.
+* 4.2   yas    08/15/18 Updated XHdcp1x_PortHdmiRxDisable function to clear
+*                       KSV_FIFO.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x_port.h"
+#include "xhdcp1x_port_hdmi.h"
+#include "xil_assert.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/* Adaptor definition at the end of this file. */
+const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortHdmiRxAdaptor;
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*************************** Function Prototypes *****************************/
+
+static int XHdcp1x_PortHdmiRxEnable(XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiRxDisable(XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiRxInit(XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiRxRead(const XHdcp1x *InstancePtr, u8 Offset,
+		void *Buf, u32 BufSize);
+static int XHdcp1x_PortHdmiRxWrite(XHdcp1x *InstancePtr, u8 Offset,
+		const void *Buf, u32 BufSize);
+static int XHdcp1x_PortHdmiRxSetRepeater(XHdcp1x *InstancePtr, u8 RptrConf);
+static void XHdcp1x_ProcessAKsvWrite(void *CallbackRef);
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function enables a HDCP port device.
+*
+* @param	InstancePtr is the id of the device to enable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiRxEnable(XHdcp1x *InstancePtr)
+{
+	u8 Buf[4];
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->Port.PhyIfPtr != NULL);
+
+	/* Initialize the Bcaps register */
+	memset(Buf, 0, 4);
+	Buf[0] |= XHDCP1X_PORT_BIT_BCAPS_HDMI;
+	Buf[0] |= XHDCP1X_PORT_BIT_BCAPS_FAST_REAUTH;
+	if(InstancePtr->IsRepeater) {
+		Buf[0] |= XHDCP1X_PORT_BIT_BCAPS_REPEATER;
+	}
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS, Buf, 1);
+
+	/* Initialize some debug registers */
+	Buf[0] = 0xDE;
+	Buf[1] = 0xAD;
+	Buf[2] = 0xBE;
+	Buf[3] = 0xEF;
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_DBG,
+			Buf, 4);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables a HDCP port device.
+*
+* @param	InstancePtr is the id of the device to disable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiRxDisable(XHdcp1x *InstancePtr)
+{
+	u8 Offset = 0;
+	u8 Value = 0;
+	int NumLeft = 0;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->Port.PhyIfPtr != NULL);
+
+	/* Clear the hdcp registers */
+	Value = 0;
+	Offset = 0x05;
+	/* Clear HDCP register space from 0x05 to AKSV (0x10) */
+	NumLeft = 11;
+	while (NumLeft-- > 0) {
+		XHdcp1x_PortHdmiRxWrite(InstancePtr, Offset++, &Value, 1);
+	}
+	/* Clear the HDCP RSVD (0x16) register */
+	Offset = 22;
+	NumLeft = 2;
+	while (NumLeft-- > 0) {
+		XHdcp1x_PortHdmiRxWrite(InstancePtr, Offset++, &Value, 1);
+	}
+	/* Clear HDCP register space from VH0 (0x20) to RSVD (0x34) */
+	Offset = 32;
+	NumLeft = 20;
+	while (NumLeft-- > 0) {
+		XHdcp1x_PortHdmiRxWrite(InstancePtr, Offset++, &Value, 1);
+	}
+	/* Clear HDCP register space for Bcaps (0x40) */
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+					&Value, 1);
+
+	/* Clear HDCP register space for Bstatus (0x41 and 0x42).
+	 * Do not clear HDMI_MODE field. */
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+					&Value, 1);
+	XHdcp1x_PortHdmiRxRead(InstancePtr, (XHDCP1X_PORT_OFFSET_BSTATUS + 1),
+					&Value, 1);
+	Value &= (XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE >> 8);
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, (XHDCP1X_PORT_OFFSET_BSTATUS + 1),
+					&Value, 1);
+
+	/* Clear HDCP register space for KSV FIFO (0x43) */
+	Value = 0;
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_KSVFIFO,
+					&Value, 1);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes a HDCP port device.
+*
+* @param	InstancePtr is the device to initialize.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiRxInit(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->Port.PhyIfPtr != NULL);
+
+	/* Disable it */
+	if (XHdcp1x_PortHdmiRxDisable(InstancePtr) != XST_SUCCESS) {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function reads a register from a HDCP port device.
+*
+* @param	InstancePtr is the device to read from.
+* @param	Offset is the offset to start reading from.
+* @param	Buf is the buffer to copy the data read.
+* @param	BufSize is the size of the buffer.
+*
+* @return	The number of bytes read.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiRxRead(const XHdcp1x *InstancePtr, u8 Offset,
+		void *Buf, u32 BufSize)
+{
+	u32 NumLeft = BufSize;
+	u8 *ReadBuf = Buf;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Buf != NULL);
+
+	/* Truncate if necessary */
+	if ((BufSize + Offset) > 0x100u) {
+		BufSize = (0x100u - Offset);
+	}
+
+	/* Write the offset */
+	if (InstancePtr->Rx.IsDdcSetAddressCallbackSet) {
+		InstancePtr->Rx.DdcSetAddressCallback(
+		    InstancePtr->Rx.DdcSetAddressCallbackRef, Offset);
+	}
+
+	/* Read the buffer */
+	while (NumLeft-- > 0) {
+		if (InstancePtr->Rx.IsDdcGetDataCallbackSet) {
+			*ReadBuf++ = InstancePtr->Rx.DdcGetDataCallback(
+			    InstancePtr->Rx.DdcGetDataCallbackRef);
+		}
+	}
+
+	return ((int)BufSize);
+}
+
+/*****************************************************************************/
+/**
+* This function writes a register from a HDCP port device.
+*
+* @param	InstancePtr is the device to write to.
+* @param	Offset is the offset to start writing to.
+* @param	Buf is the buffer containing the data to write.
+* @param	BufSize is the size of the buffer.
+*
+* @return	The number of bytes written.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiRxWrite(XHdcp1x *InstancePtr, u8 Offset,
+		const void *Buf, u32 BufSize)
+{
+	u32 NumLeft = BufSize;
+	const u8 *WriteBuf = Buf;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Buf != NULL);
+
+	/* Truncate if necessary */
+	if ((BufSize + Offset) > 0x100u) {
+		BufSize = (0x100u - Offset);
+	}
+
+	/* Write the offset */
+	if (InstancePtr->Rx.IsDdcSetAddressCallbackSet) {
+		InstancePtr->Rx.DdcSetAddressCallback(
+		    InstancePtr->Rx.DdcSetAddressCallbackRef, Offset);
+	}
+
+	/* Write the buffer */
+	while (NumLeft-- > 0) {
+		if (InstancePtr->Rx.IsDdcSetDataCallbackSet) {
+			InstancePtr->Rx.DdcSetDataCallback(
+			    InstancePtr->Rx.DdcSetDataCallbackRef, *WriteBuf++);
+		}
+	}
+
+	return ((int)BufSize);
+}
+
+/*****************************************************************************/
+/**
+* This function set the REPEATER bit in the BCaps of the device.
+*
+* @param	InstancePtr is the device to write to.
+* @param	RptrConf is the repeater capability for the device.
+*
+* @return	XST_SUCCESS.
+*
+* @note		This function sets the REPEATER bit in the BCaps register for the
+* 		upstream device to read. This can be used to update the device
+* 		configuration if it changes in real time.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiRxSetRepeater(XHdcp1x *InstancePtr, u8 RptrConf)
+{
+	u8 Value = 0;
+
+	/* Set the Ready bit in the BCaps Register */
+	XHdcp1x_PortHdmiRxRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, XHDCP1X_PORT_SIZE_BCAPS);
+	if(RptrConf) {
+		Value |= XHDCP1X_PORT_BIT_BCAPS_REPEATER;
+	}
+	else {
+		Value &= ~XHDCP1X_PORT_BIT_BCAPS_REPEATER;
+	}
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, XHDCP1X_PORT_SIZE_BCAPS);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function process a write to the AKsv register from the tx device.
+*
+* @param	CallbackRef is the device to whose register was written.
+*
+* @return	None.
+*
+* @note		This function initiates the side effects of the tx device
+*		writing the Aksv register. This is currently updates some status
+*		bits as well as kick starts a re-authentication process.
+*
+******************************************************************************/
+static void XHdcp1x_ProcessAKsvWrite(void *CallbackRef)
+{
+	XHdcp1x *InstancePtr = CallbackRef;
+	u8 Value = 0;
+
+	/* Update statistics */
+	InstancePtr->Port.Stats.IntCount++;
+
+	/* Clear bit 1 of the Ainfo register */
+	XHdcp1x_PortHdmiRxRead(InstancePtr, XHDCP1X_PORT_OFFSET_AINFO,
+			&Value, 1);
+	Value &= 0xFDu;
+	XHdcp1x_PortHdmiRxWrite(InstancePtr, XHDCP1X_PORT_OFFSET_AINFO,
+			&Value, 1);
+
+	/* Clear the Ready bit in the BCaps Register */
+	Value = 0;
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, XHDCP1X_PORT_SIZE_BCAPS);
+	Value &= 0xDFu;
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, XHDCP1X_PORT_SIZE_BCAPS);
+
+	/* Invoke authentication callback if set */
+	if (InstancePtr->Port.IsAuthCallbackSet) {
+		(*(InstancePtr->Port.AuthCallback))(InstancePtr->Port.AuthRef);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This tables defines the adaptor for the HDMI RX HDCP port driver
+*
+******************************************************************************/
+const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortHdmiRxAdaptor =
+{
+	&XHdcp1x_PortHdmiRxInit,
+	&XHdcp1x_PortHdmiRxEnable,
+	&XHdcp1x_PortHdmiRxDisable,
+	&XHdcp1x_PortHdmiRxRead,
+	&XHdcp1x_PortHdmiRxWrite,
+	NULL,
+	NULL,
+	&XHdcp1x_PortHdmiRxSetRepeater,
+	NULL,
+	NULL,
+	&XHdcp1x_ProcessAKsvWrite
+};
+
+#endif
+/* defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && (XPAR_XV_HDMIRX_NUM_INSTANCES > 0) */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_hdmi_tx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_hdmi_tx.c
@@ -0,0 +1,460 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_port_hdmi_tx.c
+* @{
+*
+* This contains the implementation of the HDCP port driver for HDMI TX
+* interfaces
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 2.00  MG     01/20/16 Assigned callback function in
+*              XHdcp1x_PortHdmiTxAdaptor to NULL
+* 2.10  MG     02/29/16 Added DDC write and read handlers
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x_port.h"
+#include "xhdcp1x_port_hdmi.h"
+#include "xil_assert.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+#define XHDCP1X_WRITE_CHUNK_SZ		(8)
+
+/* Adaptor definition at the end of this file. */
+const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortHdmiTxAdaptor;
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*************************** Function Prototypes *****************************/
+
+static int XHdcp1x_PortHdmiTxEnable(XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiTxDisable(XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiTxInit(XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiTxIsCapable(const XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiTxIsRepeater(const XHdcp1x *InstancePtr);
+static int XHdcp1x_PortHdmiTxGetRepeaterInfo(const XHdcp1x *InstancePtr,
+		u16 *Info);
+static int XHdcp1x_PortHdmiTxRead(const XHdcp1x *InstancePtr, u8 Offset,
+		void *Buf, u32 BufSize);
+static int XHdcp1x_PortHdmiTxWrite(XHdcp1x *InstancePtr, u8 Offset,
+		const void *Buf, u32 BufSize);
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function enables a HDCP port device.
+*
+* @param	InstancePtr is the id of the device to enable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxEnable(XHdcp1x *InstancePtr)
+{
+	u8 Value = 0;
+	int Status = XST_NOT_ENABLED;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->Port.PhyIfPtr != NULL);
+
+	/* Read anything to ensure that the remote end is present */
+	if ((XHdcp1x_PortHdmiTxRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, 1)) > 0) {
+		Status = XST_SUCCESS;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables a HDCP port device.
+*
+* @param	InstancePtr is the id of the device to disable.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxDisable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Nothing to do at this time */
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes an HDCP port device.
+*
+* @param	InstancePtr is the device to initialize.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxInit(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->Port.PhyIfPtr != NULL);
+
+	/* Disable it */
+	if (XHdcp1x_PortHdmiTxDisable(InstancePtr) != XST_SUCCESS) {
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function confirms the presence/capability of the remote HDCP device.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	Truth value.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxIsCapable(const XHdcp1x *InstancePtr)
+{
+	u8 Value[2] = {0, 0};
+	u16 Bstatus = 0;
+	int IsCapable = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if the transmitter device is HDMI or DVI. */
+	if(InstancePtr->Tx.TxIsHdmi == TRUE) {
+
+		/* If an HDCP 1.x register is successfully read, then the
+	        downstream device is ready to authenticate. */
+		if (XHdcp1x_PortHdmiTxRead(InstancePtr,
+			XHDCP1X_PORT_OFFSET_BCAPS, Value, 1)) {
+
+			/* Check if connected device is DVI or HDMI
+			 * capable in Bcaps. */
+			if (Value[0] & 0x80) {
+
+				if (XHdcp1x_PortHdmiTxRead(InstancePtr,
+				     XHDCP1X_PORT_OFFSET_BSTATUS, Value, 2)) {
+					/* If it is HDMI capable, check if
+					 * HDMI_MODE in BStatus is true. */
+					Bstatus = Value[0];
+					Bstatus |= Value[1] << 8;
+
+					/* Downstream receiver has
+					 * transitioned to HDMI mode and is
+					 * ready to authenticate. */
+					if (Bstatus & 0x1000) {
+						IsCapable = TRUE;
+					}
+					/* If the downstream receiver has
+					 * not yet set the HDMI_MODE in
+					 * BStatus it isn't ready yet. */
+				}
+			}
+			/* The downstream device is DVI, but the transmitter is
+			 * configured in HDMI mode. This is an error. In this
+			 * case we keep the IsCapable value set to FALSE. */
+			else {
+				IsCapable = FALSE;
+			}
+		}
+	}
+	/* DVI */
+	else if (InstancePtr->Tx.TxIsHdmi == FALSE) {
+		/* If an HDCP 1.x register is successfully read, then the
+	        downstream device is ready to authenticate. */
+		if (XHdcp1x_PortHdmiTxRead(InstancePtr,
+			XHDCP1X_PORT_OFFSET_BCAPS, Value, 1)) {
+			IsCapable = TRUE;
+		}
+	}
+
+
+	return (IsCapable);
+}
+
+/*****************************************************************************/
+/**
+* This function confirms if the remote HDCP device is a repeater.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return	Truth value.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxIsRepeater(const XHdcp1x *InstancePtr)
+{
+	u8 Value = 0;
+	int IsRepeater = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check for repeater */
+	if (XHdcp1x_PortHdmiTxRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, 1) > 0) {
+		if ((Value & XHDCP1X_PORT_BIT_BCAPS_REPEATER) != 0) {
+			IsRepeater = TRUE;
+		}
+	}
+
+	return (IsRepeater);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the repeater information.
+*
+* @param	InstancePtr is the device to query.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_DEVICE_BUSY if the device is busy.
+*		- XST_RECV_ERROR if receiver read failed.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxGetRepeaterInfo(const XHdcp1x *InstancePtr,
+		u16 *Info)
+{
+	u8 Value = 0;
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Info != NULL);
+
+	/* Read the remote capabilities */
+	if (XHdcp1x_PortHdmiTxRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+			&Value, 1) > 0) {
+		u8 ReadyMask = 0;
+
+		/* Determine ReadyMask */
+		ReadyMask  = XHDCP1X_PORT_BIT_BCAPS_REPEATER;
+		ReadyMask |= XHDCP1X_PORT_BIT_BCAPS_READY;
+
+		/* Check for repeater and ksv fifo ready */
+		if ((Value & ReadyMask) == ReadyMask) {
+			u8 Buf[2];
+			u16 U16Value = 0;
+
+			/* Read the Bstatus */
+			XHdcp1x_PortHdmiTxRead(InstancePtr,
+				XHDCP1X_PORT_OFFSET_BSTATUS, Buf, 2);
+
+			/* Determine Value */
+			XHDCP1X_PORT_BUF_TO_UINT(U16Value, Buf, 16);
+
+			/* Update Info */
+			*Info = (U16Value & 0x1FFFu);
+
+		}
+		else {
+			Status = XST_DEVICE_BUSY;
+		}
+	}
+	else {
+		Status = XST_RECV_ERROR;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function reads a register from a HDCP port device.
+*
+* @param	InstancePtr is the device to read from.
+* @param	Offset is the offset to start reading from.
+* @param	Buf is the buffer to copy the data read.
+* @param	BufSize is the size of the buffer.
+*
+* @return	The number of bytes read.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxRead(const XHdcp1x *InstancePtr, u8 Offset,
+		void *Buf, u32 BufSize)
+{
+	u8 Slave = 0x3Au;
+	int NumRead = 0;
+	u8 *ReadBuf = Buf;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Buf != NULL);
+	Xil_AssertNonvoid(InstancePtr->Tx.DdcRead != NULL);
+	Xil_AssertNonvoid(InstancePtr->Tx.DdcWrite != NULL);
+
+	/* Truncate if necessary */
+	if ((BufSize + Offset) > 0x100u) {
+		BufSize = (0x100u - Offset);
+	}
+
+	/* Write the address and check for failure */
+	if (InstancePtr->Tx.DdcWrite(Slave, 1, &Offset, FALSE,
+		InstancePtr->Tx.DdcWriteRef) != XST_SUCCESS) {
+		NumRead = -1;
+	}
+	/* Read the data back and check for failure */
+	else if (InstancePtr->Tx.DdcRead(Slave, BufSize, ReadBuf, TRUE,
+		InstancePtr->Tx.DdcReadRef) != XST_SUCCESS) {
+		NumRead = -2;
+	}
+	/* Success - just update NumRead */
+	else {
+		NumRead = (int)BufSize;
+	}
+
+	return (NumRead);
+}
+
+/*****************************************************************************/
+/**
+* This function writes a register from a HDCP port device.
+*
+* @param	InstancePtr is the device to write to.
+* @param	Offset is the offset to start writing to.
+* @param	Buf is the buffer containing the data to write.
+* @param	BufSize is the size of the buffer.
+*
+* @return	The number of bytes written.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_PortHdmiTxWrite(XHdcp1x *InstancePtr, u8 Offset,
+		const void *Buf, u32 BufSize)
+{
+	u8 Slave = 0x3Au;
+	u8 TxBuf[XHDCP1X_WRITE_CHUNK_SZ + 1];
+	int NumWritten = 0;
+	u32 ThisTime = 0;
+	const u8 *WriteBuf = Buf;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Buf != NULL);
+	Xil_AssertNonvoid(InstancePtr->Tx.DdcWrite != NULL);
+
+	/* Truncate if necessary */
+	if ((BufSize + Offset) > 0x100u) {
+		BufSize = (0x100u - Offset);
+	}
+
+	/* Iterate through the buffer */
+	do {
+		/* Determine ThisTime */
+		ThisTime = XHDCP1X_WRITE_CHUNK_SZ;
+		if (ThisTime > BufSize) {
+			ThisTime = BufSize;
+		}
+
+		/* Format TxBuf */
+		TxBuf[0] = Offset;
+		memcpy(&(TxBuf[1]), WriteBuf, ThisTime);
+
+		/* Write the TxBuf */
+		if (InstancePtr->Tx.DdcWrite(Slave, (ThisTime + 1), TxBuf,
+			TRUE, InstancePtr->Tx.DdcWriteRef)
+				!= XST_SUCCESS) {
+			/* Update NumWritten and break */
+			NumWritten = -1;
+			break;
+		}
+
+		/* Update for loop */
+		NumWritten += ThisTime;
+		WriteBuf += ThisTime;
+		BufSize -= ThisTime;
+	} while ((BufSize != 0) && (NumWritten > 0));
+
+	/* Return */
+	return (NumWritten);
+}
+
+/*****************************************************************************/
+/**
+* This tables defines the adaptor for the HDMI TX HDCP port driver
+*
+******************************************************************************/
+const XHdcp1x_PortPhyIfAdaptor XHdcp1x_PortHdmiTxAdaptor =
+{
+	&XHdcp1x_PortHdmiTxInit,
+	&XHdcp1x_PortHdmiTxEnable,
+	&XHdcp1x_PortHdmiTxDisable,
+	&XHdcp1x_PortHdmiTxRead,
+	&XHdcp1x_PortHdmiTxWrite,
+	&XHdcp1x_PortHdmiTxIsCapable,
+	&XHdcp1x_PortHdmiTxIsRepeater,
+	NULL,
+	&XHdcp1x_PortHdmiTxGetRepeaterInfo,
+	NULL,
+	NULL
+};
+
+#endif
+/* defined(XPAR_XV_HDMITX_NUM_INSTANCES) && (XPAR_XV_HDMITX_NUM_INSTANCES > 0) */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_port_intr.c
@@ -0,0 +1,130 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_port_intr.c
+* @{
+*
+* This contains the interrupt related functions of the Xilinx HDCP port driver
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x_port.h"
+#include "xil_assert.h"
+#include "xil_types.h"
+
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                           Callback Function Type
+* ------------------------------------  -------------------------------------
+* (XHDCP1X_PORT_HANDLER_AUTHENTICATE)   AuthCallback
+* </pre>
+*
+* @param	InstancePtr is a pointer to the HDCP port instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return
+*		- XST_SUCCESS if callback function installed successfully.
+*		- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*		installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp1x_PortSetCallback(XHdcp1x *InstancePtr, u32 HandlerType,
+                XHdcp1x_Callback CallbackFunc, void *CallbackRef)
+{
+	u32 Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType >= (XHDCP1X_PORT_HANDLER_AUTHENTICATE));
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	/* Check for handler type */
+	switch (HandlerType) {
+		/* Authentication Callback */
+		case (XHDCP1X_PORT_HANDLER_AUTHENTICATE):
+			InstancePtr->Port.AuthCallback = CallbackFunc;
+			InstancePtr->Port.AuthRef = CallbackRef;
+			InstancePtr->Port.IsAuthCallbackSet = (TRUE);
+			break;
+
+		default:
+			Status = (XST_INVALID_PARAM);
+			break;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This handles an interrupt generated by a HDCP port device.
+*
+* @param	InstancePtr is the device to write to.
+* @param	IntCause is the interrupt cause bit map.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_PortHandleInterrupt(XHdcp1x *InstancePtr, u32 IntCause)
+{
+	const XHdcp1x_PortPhyIfAdaptor *Adaptor = NULL;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Determine Adaptor */
+	Adaptor = InstancePtr->Port.Adaptor;
+
+	/* Check for adaptor function and invoke if present */
+	if ((Adaptor != NULL) && (Adaptor->IntrHandler != NULL)) {
+		InstancePtr->Port.Stats.IntCount++;
+		(*(Adaptor->IntrHandler))(InstancePtr, IntCause);
+	}
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_rx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_rx.c
@@ -0,0 +1,2837 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_rx.c
+* @{
+*
+* This contains the main implementation file for the Xilinx HDCP receive state
+* machine
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 1.10  MG     01/18/16 Added function XHdcp1x_RxIsEnabled and
+*                       XHdcp1x_RxIsInProgress.
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added a new enum XHdcp1x_EventType value:
+*                       XHDCP1X_EVENT_DOWNSTREAMREADY.
+*                       Added new XHdcp1x_StateType values:
+*                       XHDCP1X_STATE_WAITFORDOWNSTREAM,
+*                       XHDCP1X_STATE_ASSEMBLEKSVLIST.
+*                       Added a new function:
+*                       XHdcp1x_RxDownstreamReady, XHdcp1x_RxGetRepeaterInfo,
+*                       XHdcp1x_RxSetCallBack.
+*                       Updated the following functions for Repeater:
+*                       XHdcp1x_RxStartComputations,
+*                       XHdcp1x_RxPollForComputations, XHdcp1x_RxEnterState,
+*                       XHdcp1x_RxDoTheState.
+* 3.1   yas    07/28/16 Repeater functionality extended to support HDMI.
+*                       Removed the XHdcp1x_RxDownstreamReadyCallback.
+*                       Added fucntions,
+*                       XHdcp1x_RxSetRepeaterBcaps,XHdcp1x_RxIsInComputations,
+*                       XHdcp1x_RxIsInWaitforready, XHdcp1x_RxHandleTimeout,
+*                       XHdcp1x_RxStartTimer, XHdcp1x_RxStopTimer,
+*                       XHdcp1x_RxBusyDelay, XHdcp1x_RxSetTopologyUpdate,
+*                       XHdcp1x_RxSetTopology, XHdcp1x_RxSetTopologyKSVList,
+*                       XHdcp1x_RxSetTopologyDepth,
+*                       XHdcp1x_RxSetTopologyDeviceCnt,
+*                       XHdcp1x_RxSetTopologyMaxCascadeExceeded,
+*                       XHdcp1x_RxSetTopologyMaxDevsExceeded,
+*                       XHdcp1x_RxCheckEncryptionChange.
+* 4.1   yas    11/10/16 Added function XHdcp1x_RxSetHdmiMode.
+* </pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files *********************************/
+
+
+//#include <stdio.h>
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+#include "xhdcp1x_debug.h"
+#include "xhdcp1x_port.h"
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+#include "xhdcp1x_port_hdmi.h"
+#else
+#include "xhdcp1x_port_dp.h"
+#endif
+#include "xhdcp1x_rx.h"
+#include "xhdcp1x_platform.h"
+#include "sha1.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+#define XVPHY_FLAG_PHY_UP	(1u << 0)  /**< Flag to track physical state */
+
+#define XVPHY_TMO_5MS		(5u)    /**< Timeout value for 5ms */
+#define XVPHY_TMO_100MS		(100u)    /**< Timeout value for 100ms */
+#define XVPHY_TMO_1SECOND	(1000u)    /**< Timeout value for 1s */
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * This enumerates the Event Types for HDCP Receiver state machine.
+ */
+typedef enum {
+	XHDCP1X_EVENT_NULL,
+	XHDCP1X_EVENT_AUTHENTICATE,
+	XHDCP1X_EVENT_CHECK,
+	XHDCP1X_EVENT_DISABLE,
+	XHDCP1X_EVENT_ENABLE,
+	XHDCP1X_EVENT_PHYDOWN,
+	XHDCP1X_EVENT_PHYUP,
+	XHDCP1X_EVENT_POLL,
+	XHDCP1X_EVENT_UPDATERi,
+	XHDCP1X_EVENT_TIMEOUT,
+	XHDCP1X_EVENT_DOWNSTREAMREADY,
+} XHdcp1x_EventType;
+
+/**
+ * This enumerates the State Types for HDCP Receiver state machine.
+ */
+typedef enum {
+	XHDCP1X_STATE_DISABLED = XHDCP1X_RX_STATE_DISABLED,
+	XHDCP1X_STATE_UNAUTHENTICATED = XHDCP1X_RX_STATE_UNAUTHENTICATED,
+	XHDCP1X_STATE_COMPUTATIONS = XHDCP1X_RX_STATE_COMPUTATIONS,
+	XHDCP1X_STATE_WAITFORDOWNSTREAM = XHDCP1X_RX_STATE_WAITFORDOWNSTREAM,
+	XHDCP1X_STATE_ASSEMBLEKSVLIST = XHDCP1X_RX_STATE_ASSEMBLEKSVLIST,
+	XHDCP1X_STATE_AUTHENTICATED = XHDCP1X_RX_STATE_AUTHENTICATED,
+	XHDCP1X_STATE_LINKINTEGRITYFAILED = XHDCP1X_RX_STATE_LINKINTEGRITYFAILED,
+	XHDCP1X_STATE_PHYDOWN = XHDCP1X_RX_STATE_PHYDOWN,
+} XHdcp1x_StateType;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*************************** Function Prototypes *****************************/
+
+static void XHdcp1x_RxDebugLog(const XHdcp1x *InstancePtr, const char *LogMsg);
+static void XHdcp1x_RxPostEvent(XHdcp1x *InstancePtr, XHdcp1x_EventType Event);
+static void XHdcp1x_RxStartTimer(XHdcp1x *InstancePtr, u16 TimeoutInMs);
+static void XHdcp1x_RxStopTimer(XHdcp1x *InstancePtr);
+#if XHDCP1X_ADDITIONAL_DEBUG
+static void XHdcp1x_RxBusyDelay(XHdcp1x *InstancePtr, u16 DelayInMs);
+#endif
+static void XHdcp1x_RxAuthCallback(void *Parameter);
+static void XHdcp1x_RxLinkFailCallback(void *Parameter);
+static void XHdcp1x_RxRiUpdateCallback(void *Parameter);
+static void XHdcp1x_RxSetCheckLinkState(XHdcp1x *InstancePtr, int IsEnabled);
+static void XHdcp1x_RxEnableState(XHdcp1x *InstancePtr);
+static void XHdcp1x_RxDisableState(XHdcp1x *InstancePtr);
+static void XHdcp1x_RxStartComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxPollForComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static int XHdcp1x_RxCalculateSHA1Value(XHdcp1x *InstancePtr,
+		u16 RepeaterInfo);
+static void XHdcp1x_RxAssembleKSVList(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxUpdateRi(XHdcp1x *InstancePtr);
+static void XHdcp1x_RxCheckLinkIntegrity(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxReportLinkIntegrityFailure(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxRunDisabledState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxRunUnauthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxRunComputationsState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxRunAuthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxRunLinkIntegrityFailedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxRunPhysicalLayerDownState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxEnterState(XHdcp1x *InstancePtr, XHdcp1x_StateType State,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_RxExitState(XHdcp1x *InstancePtr, XHdcp1x_StateType State);
+static void XHdcp1x_RxDoTheState(XHdcp1x *InstancePtr, XHdcp1x_EventType Event);
+static void XHdcp1x_RxProcessPending(XHdcp1x *InstancePtr);
+static const char *XHdcp1x_RxStateToString(XHdcp1x_StateType State);
+#if XHDCP1X_ADDITIONAL_DEBUG
+static const char *XHdcp1x_RxEventToString(XHdcp1x_EventType Event);
+#endif
+
+/************************** Function Definitions *****************************/
+/*****************************************************************************/
+/**
+* This function installs callback functions for the given
+* HandlerType:
+*
+* @param	InstancePtr is a pointer to the HDCP core instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*			callback function when it is invoked.
+*
+* @return
+*		- XST_SUCCESS if callback function installed successfully.
+*		- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*			installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp1x_RxSetCallback(XHdcp1x *InstancePtr,
+	XHdcp1x_HandlerType HandlerType, void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType > (XHDCP1X_HANDLER_UNDEFINED));
+	Xil_AssertNonvoid(HandlerType < (XHDCP1X_HANDLER_INVALID));
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	u32 Status;
+
+	/* Check for handler type */
+	switch (HandlerType)
+	{
+		case (XHDCP1X_HANDLER_DDC_SETREGADDR):
+			InstancePtr->Rx.DdcSetAddressCallback
+				= (XHdcp1x_SetDdcHandler)CallbackFunc;
+			InstancePtr->Rx.DdcSetAddressCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsDdcSetAddressCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		case (XHDCP1X_HANDLER_DDC_SETREGDATA):
+			InstancePtr->Rx.DdcSetDataCallback
+				= (XHdcp1x_SetDdcHandler)CallbackFunc;
+			InstancePtr->Rx.DdcSetDataCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsDdcSetDataCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		case (XHDCP1X_HANDLER_DDC_GETREGDATA):
+			InstancePtr->Rx.DdcGetDataCallback
+				= (XHdcp1x_GetDdcHandler)CallbackFunc;
+			InstancePtr->Rx.DdcGetDataCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsDdcGetDataCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		/* Repeater - trigger Downstream Authentication */
+		/* Eqilvalent of case
+		 * (XHDCP1X_RPTR_HDLR_TRIG_DOWNSTREAM_AUTH):
+		 */
+		case (XHDCP1X_HANDLER_RPTR_TRIGDWNSTRMAUTH):
+			InstancePtr->Rx.RepeaterDownstreamAuthCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Rx.RepeaterDownstreamAuthRef
+				= CallbackRef;
+			InstancePtr->Rx.IsRepeaterDownstreamAuthCallbackSet
+				= (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		// authenticated
+		case (XHDCP1X_HANDLER_AUTHENTICATED):
+			InstancePtr->Rx.AuthenticatedCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Rx.AuthenticatedCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsAuthenticatedCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		// unauthenticated
+		case (XHDCP1X_HANDLER_UNAUTHENTICATED):
+			InstancePtr->Rx.UnauthenticatedCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Rx.UnauthenticatedCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsUnauthenticatedCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		// topology updated
+		case (XHDCP1X_HANDLER_TOPOLOGY_UPDATE):
+			InstancePtr->Rx.TopologyUpdateCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Rx.TopologyUpdateCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsTopologyUpdateCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		// encryption updated
+		case (XHDCP1X_HANDLER_ENCRYPTION_UPDATE):
+			InstancePtr->Rx.EncryptionUpdateCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Rx.EncryptionUpdateCallbackRef
+				= CallbackRef;
+			InstancePtr->Rx.IsEncryptionUpdateCallbackSet = (TRUE);
+			Status = XST_SUCCESS;
+			break;
+
+		default:
+			Status = XST_INVALID_PARAM;
+			break;
+	}
+
+	return (Status);
+}
+
+void XHdcp1x_RxLoadBksvToBuf(XHdcp1x *InstancePtr)
+{
+	u64 MyKsv = 0;
+	u8 Buf[8];
+	int IsEnabled = FALSE;
+
+	IsEnabled = XHdcp1x_CipherIsEnabled(InstancePtr);
+
+	/* Enable the crypto engine */
+	XHdcp1x_CipherEnable(InstancePtr);
+
+	/* Read MyKsv */
+	MyKsv = XHdcp1x_CipherGetLocalKsv(InstancePtr);
+
+	/* If unknown - try again for good luck */
+	if (MyKsv == 0) {
+		MyKsv = XHdcp1x_CipherGetLocalKsv(InstancePtr);
+	}
+
+	/* Initialize Bksv */
+	memset(Buf, 0, 8);
+	XHDCP1X_PORT_UINT_TO_BUF(Buf, MyKsv,
+			XHDCP1X_PORT_SIZE_BKSV * 8);
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BKSV, Buf,
+			XHDCP1X_PORT_SIZE_BKSV);
+
+	if (!IsEnabled)
+		XHdcp1x_CipherDisable(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes a HDCP receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_RxInit(XHdcp1x *InstancePtr)
+{
+	XHdcp1x_StateType DummyState = XHDCP1X_STATE_DISABLED;
+
+	/* Update theHandler */
+	InstancePtr->Rx.PendingEvents = 0;
+
+	/* Kick the state machine */
+	XHdcp1x_RxEnterState(InstancePtr, XHDCP1X_STATE_DISABLED, &DummyState);
+}
+
+/*****************************************************************************/
+/**
+* This function polls the HDCP receiver module.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+ ******************************************************************************/
+int XHdcp1x_RxPoll(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Process any pending events */
+	XHdcp1x_RxProcessPending(InstancePtr);
+
+	/* Poll it */
+	XHdcp1x_RxDoTheState(InstancePtr, XHDCP1X_EVENT_POLL);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function set the REPEATER bit for the HDCP RX interface.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	IsRptr is the truth value to determine if the repeater bit
+* 		in the port registers is to be set.
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		This function disables and then re-enables the interface.
+*
+ ******************************************************************************/
+int XHdcp1x_RxSetRepeaterBcaps(XHdcp1x *InstancePtr, u8 IsRptr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	Status = XHdcp1x_PortSetRepeater(InstancePtr, IsRptr);
+	if (Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function resets an HDCP interface.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		This function disables and then re-enables the interface.
+*
+ ******************************************************************************/
+int XHdcp1x_RxReset(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Reset it */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_DISABLE);
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_ENABLE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function enables a HDCP receive interface.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxEnable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post it */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_ENABLE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables a HDCP receive interface.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxDisable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post it */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_DISABLE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if is enabled.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	Truth value indicating is enabled (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxIsEnabled(const XHdcp1x *InstancePtr)
+{
+	int IsEnabled = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Case-wise process the current state of Rx state machine */
+	switch (InstancePtr->Rx.CurrentState) {
+		case XHDCP1X_STATE_DISABLED:
+			IsEnabled = FALSE;
+			break;
+
+		/* Otherwise */
+		default:
+			IsEnabled = TRUE;
+			break;
+	}
+
+	return (IsEnabled);
+}
+
+/*****************************************************************************/
+/**
+* This function updates the physical state of an HDCP interface.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	IsUp is truth value indicating the status of physical interface.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxSetPhysicalState(XHdcp1x *InstancePtr, int IsUp)
+{
+	int Status = XST_SUCCESS;
+	XHdcp1x_EventType Event = XHDCP1X_EVENT_PHYDOWN;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Event */
+	if (IsUp) {
+		Event = XHDCP1X_EVENT_PHYUP;
+	}
+
+	/* Post it */
+	XHdcp1x_RxPostEvent(InstancePtr, Event);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function set the lane count of an hdcp interface.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	LaneCount is the number of lanes of the interface.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxSetLaneCount(XHdcp1x *InstancePtr, int LaneCount)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(LaneCount > 0);
+
+	/* Set it */
+	return (XHdcp1x_CipherSetNumLanes(InstancePtr, LaneCount));
+}
+
+/*****************************************************************************/
+/**
+* This function initiates downstream ready/ assemble ksv list on an interface.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxDownstreamReady(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post the re-authentication request */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_DOWNSTREAMREADY);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initiates authentication on an interface.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxAuthenticate(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post the re-authentication request */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_AUTHENTICATE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if authentication is in
+* progress.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	Truth value indicating in progress (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxIsInProgress(const XHdcp1x *InstancePtr)
+{
+	int IsInProgress = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Case-wise process the current state of Rx state machine  */
+	switch (InstancePtr->Rx.CurrentState) {
+		case XHDCP1X_STATE_COMPUTATIONS:
+			IsInProgress = TRUE;
+			break;
+
+		/* Otherwise */
+		default:
+			IsInProgress = FALSE;
+			break;
+	}
+
+	return (IsInProgress);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if its been authenticated.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	Truth value indicating authenticated (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxIsAuthenticated(const XHdcp1x *InstancePtr)
+{
+	int IsAuthenticated = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine IsAuthenticated */
+	if (InstancePtr->Rx.CurrentState == XHDCP1X_STATE_AUTHENTICATED) {
+		IsAuthenticated = TRUE;
+	}
+
+	return (IsAuthenticated);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if its in the computations state.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	Truth value indicating authenticated (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxIsInComputations(const XHdcp1x *InstancePtr)
+{
+	int IsInComp = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine IsAuthenticated */
+	if (InstancePtr->Rx.CurrentState == XHDCP1X_STATE_COMPUTATIONS) {
+		IsInComp = TRUE;
+	}
+
+	return (IsInComp);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if its in the
+* wait-for-downstream-ready state.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	Truth value indicating authenticated (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxIsInWaitforready(const XHdcp1x *InstancePtr)
+{
+	int IsInWfr = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine IsAuthenticated */
+	if (InstancePtr->Rx.CurrentState == XHDCP1X_STATE_WAITFORDOWNSTREAM) {
+		IsInWfr = TRUE;
+	}
+
+	return (IsInWfr);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the current encryption stream map.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	The current encryption stream map.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_RxGetEncryption(const XHdcp1x *InstancePtr)
+{
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Get it */
+	return (XHdcp1x_CipherGetEncryption(InstancePtr));
+}
+
+/*****************************************************************************/
+/**
+* This function handles a timeout on an HDCP interface.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_RxHandleTimeout(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Post the timeout */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_TIMEOUT);
+}
+
+/*****************************************************************************/
+/**
+* This function implements the debug display output for receiver instances.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxInfo(const XHdcp1x *InstancePtr)
+{
+	u64 LocalKsv = 0;
+	u32 Version = 0;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Display it */
+	XDEBUG_PRINTF("Type:            ");
+	if (InstancePtr->Config.IsHDMI) {
+		XDEBUG_PRINTF("hdmi-rx\r\n");
+	}
+	else {
+		XDEBUG_PRINTF("dp-rx\r\n");
+	}
+	XDEBUG_PRINTF("Current State:   %s\r\n",
+		XHdcp1x_RxStateToString(InstancePtr->Rx.CurrentState));
+	XDEBUG_PRINTF("Previous State:  %s\r\n",
+		XHdcp1x_RxStateToString(InstancePtr->Rx.PreviousState));
+	XDEBUG_PRINTF("Encrypted?:      %s\r\n",
+		XHdcp1x_IsEncrypted(InstancePtr) ? "Yes" : "No");
+	XDEBUG_PRINTF("Flags:           %04X\r\n",
+		InstancePtr->Rx.Flags);
+	Version = XHdcp1x_GetDriverVersion();
+	XDEBUG_PRINTF("Driver Version:  %d.%02d.%02d\r\n",
+		((Version >> 16) &0xFFFFu), ((Version >> 8) & 0xFFu),
+		(Version & 0xFFu));
+	Version = XHdcp1x_CipherGetVersion(InstancePtr);
+	XDEBUG_PRINTF("Cipher Version:  %d.%02d.%02d\r\n",
+		((Version >> 16) &0xFFFFu), ((Version >> 8) & 0xFFu),
+		(Version & 0xFFu));
+	LocalKsv = XHdcp1x_CipherGetLocalKsv(InstancePtr);
+	XDEBUG_PRINTF("Local KSV:       %02lX", (LocalKsv >> 32));
+	XDEBUG_PRINTF("%08lX\r\n", (LocalKsv & 0xFFFFFFFFu));
+
+	XDEBUG_PRINTF("\r\n");
+	XDEBUG_PRINTF("Rx Stats\r\n");
+	XDEBUG_PRINTF("Auth Attempts:   %d\r\n",
+		InstancePtr->Rx.Stats.AuthAttempts);
+	XDEBUG_PRINTF("Link Failures:   %d\r\n",
+		InstancePtr->Rx.Stats.LinkFailures);
+	XDEBUG_PRINTF("Ri Updates:      %d\r\n",
+		InstancePtr->Rx.Stats.RiUpdates);
+
+	XDEBUG_PRINTF("\r\n");
+	XDEBUG_PRINTF("Cipher Stats\r\n");
+	XDEBUG_PRINTF("Int Count:       %d\r\n",
+		InstancePtr->Cipher.Stats.IntCount);
+
+	XDEBUG_PRINTF("\r\n");
+	XDEBUG_PRINTF("Port Stats\r\n");
+	XDEBUG_PRINTF("Int Count:       %d\r\n",
+		InstancePtr->Port.Stats.IntCount);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function copies the V'H0, V'H1, V'H2, V'H3, V'H4, KSVList and
+* BInfo values in the HDCP RX HDCP Instance for Repeater validation .
+*
+* @param	InstancePtr is the receiver instance.
+* @param	RepeaterInfoPtr is the Repeater information in the
+* 		transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_RxGetRepeaterInfo(XHdcp1x *InstancePtr,
+		XHdcp1x_RepeaterExchange *RepeaterInfoPtr)
+{
+	int Status = XST_SUCCESS;
+	u32 ksvCount=0;
+	u32 ksvsToCopy;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(RepeaterInfoPtr != NULL);
+
+	/*
+	 * Copy the Depth read from the downstream HDCP device and
+	 * increment it by one to account for the Repeater itself
+	 */
+	InstancePtr->RepeaterValues.Depth = RepeaterInfoPtr->Depth + 1;
+
+	/* Copy the device count read from the downstream HDCP device */
+	InstancePtr->RepeaterValues.DeviceCount
+			= RepeaterInfoPtr->DeviceCount;
+
+	/* Copy the KSVList */
+	ksvsToCopy = InstancePtr->RepeaterValues.DeviceCount;
+
+	for(ksvCount=0 ; ksvCount < ksvsToCopy ; ksvCount++) {
+		InstancePtr->RepeaterValues.KsvList[ksvCount]
+			= RepeaterInfoPtr->KsvList[ksvCount];
+	}
+
+	/* Copy the SHA1 Hash value V'H0 */
+	InstancePtr->RepeaterValues.V[0] = RepeaterInfoPtr->V[0];
+
+	/* Copy the SHA1 Hash value V'H1 */
+	InstancePtr->RepeaterValues.V[1] = RepeaterInfoPtr->V[1];
+
+	/* Copy the SHA1 Hash value V'H2 */
+	InstancePtr->RepeaterValues.V[2] = RepeaterInfoPtr->V[2];
+
+	/* Copy the SHA1 Hash value V'H3 */
+	InstancePtr->RepeaterValues.V[3] = RepeaterInfoPtr->V[3];
+
+	/* Copy the SHA1 Hash value V'H4 */
+	InstancePtr->RepeaterValues.V[4] = RepeaterInfoPtr->V[4];
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function logs a debug message on behalf of a handler state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	LogMsg is the message to log.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxDebugLog(const XHdcp1x *InstancePtr, const char *LogMsg)
+{
+	char Label[16];
+
+	/* Format Label */
+	snprintf(Label, sizeof(Label), "hdcp-rx(%hu) - ",
+			 InstancePtr->Config.DeviceId);
+
+	/* Log it */
+	XHDCP1X_DEBUG_LOGMSG(Label);
+	XHDCP1X_DEBUG_LOGMSG(LogMsg);
+	XHDCP1X_DEBUG_LOGMSG("\n");
+}
+
+/*****************************************************************************/
+/**
+* This function posts an event to a state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to post.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxPostEvent(XHdcp1x *InstancePtr, XHdcp1x_EventType Event)
+{
+	/* Check for disable and clear any pending enable */
+	if (Event == XHDCP1X_EVENT_DISABLE) {
+		InstancePtr->Rx.PendingEvents &= ~(1u << XHDCP1X_EVENT_ENABLE);
+	}
+	/* Check for phy-down and clear any pending phy-up */
+	else if (Event == XHDCP1X_EVENT_PHYDOWN) {
+		InstancePtr->Rx.PendingEvents &= ~(1u << XHDCP1X_EVENT_PHYUP);
+	}
+
+	/* Post it */
+	InstancePtr->Rx.PendingEvents |= (1u << Event);
+}
+
+/*****************************************************************************/
+/**
+* This function starts a state machine's timer.
+*
+* @param	InstancePtr is the state machine.
+* @param	TimeoutInMs is the timeout in milli-seconds.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxStartTimer(XHdcp1x *InstancePtr, u16 TimeoutInMs)
+{
+	/* Start it */
+	XHdcp1x_PlatformTimerStart(InstancePtr, TimeoutInMs);
+}
+
+/*****************************************************************************/
+/**
+* This function stops a state machine's timer.
+*
+* @param	InstancePtr is the state machine.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxStopTimer(XHdcp1x *InstancePtr)
+{
+	/* Stop it */
+	XHdcp1x_PlatformTimerStop(InstancePtr);
+}
+
+#if XHDCP1X_ADDITIONAL_DEBUG
+/*****************************************************************************/
+/**
+* This function busy delays a state machine.
+*
+* @param	InstancePtr is the state machine.
+* @param	DelayInMs is the delay time in milli-seconds.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxBusyDelay(XHdcp1x *InstancePtr, u16 DelayInMs)
+{
+	/* Busy wait */
+	XHdcp1x_PlatformTimerBusy(InstancePtr, DelayInMs);
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function acts as the re-authentication callback for a state machine.
+*
+* @param	Parameter is the parameter specified during registration.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxAuthCallback(void *Parameter)
+{
+	XHdcp1x *InstancePtr = (XHdcp1x *)Parameter;
+
+	/* Post the re-authentication request */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_AUTHENTICATE);
+}
+
+/*****************************************************************************/
+/**
+* This function acts as the link failure callback for a state machine.
+*
+* @param	Parameter is the parameter specified during registration.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxLinkFailCallback(void *Parameter)
+{
+	XHdcp1x *InstancePtr = (XHdcp1x *)Parameter;
+
+	/* Post the check request */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_CHECK);
+}
+
+/*****************************************************************************/
+/**
+* This function acts as the Ri register update callback for a state machine.
+*
+* @param	Parameter is the parameter specified during registration.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRiUpdateCallback(void *Parameter)
+{
+	XHdcp1x *InstancePtr = (XHdcp1x *)Parameter;
+
+	if(InstancePtr->Rx.CurrentState == XHDCP1X_STATE_AUTHENTICATED) {
+		/* Update the Ri value. */
+		XHdcp1x_RxUpdateRi(InstancePtr);
+	} else {
+		/* Post the update Ri request. */
+		XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_UPDATERi);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the check link state of the handler.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	IsEnabled is truth value indicating on/off.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxSetCheckLinkState(XHdcp1x *InstancePtr, int IsEnabled)
+{
+	/* Check for HDMI */
+	if (InstancePtr->Config.IsHDMI) {
+		XHdcp1x_CipherSetRiUpdate(InstancePtr, IsEnabled);
+	}
+	/* Check for DP */
+	else {
+		XHdcp1x_CipherSetLinkStateCheck(InstancePtr, IsEnabled);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function enables a receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxEnableState(XHdcp1x *InstancePtr)
+{
+	u64 MyKsv = 0;
+	u8 Buf[8];
+
+	/* Disable and register the link failure callback */
+	XHdcp1x_CipherSetLinkStateCheck(InstancePtr, FALSE);
+	XHdcp1x_CipherSetCallback(InstancePtr,
+			XHDCP1X_CIPHER_HANDLER_LINK_FAILURE,
+			&XHdcp1x_RxLinkFailCallback, InstancePtr);
+
+	/* Disable and register the Ri callback */
+	XHdcp1x_CipherSetRiUpdate(InstancePtr, FALSE);
+	XHdcp1x_CipherSetCallback(InstancePtr,
+			XHDCP1X_CIPHER_HANDLER_Ri_UPDATE,
+			&XHdcp1x_RxRiUpdateCallback, InstancePtr);
+
+	/* Enable the crypto engine */
+	XHdcp1x_CipherEnable(InstancePtr);
+
+	/* Register the re-authentication callback */
+	XHdcp1x_PortSetCallback(InstancePtr,
+			XHDCP1X_PORT_HANDLER_AUTHENTICATE,
+			&XHdcp1x_RxAuthCallback, InstancePtr);
+
+	/* Enable the hdcp port */
+	XHdcp1x_PortEnable(InstancePtr);
+
+	/* Update the hdcp encryption status */
+	InstancePtr->Rx.XORState.CurrentState = FALSE;
+}
+
+/*****************************************************************************/
+/**
+* This function disables a receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxDisableState(XHdcp1x *InstancePtr)
+{
+	/* Disable the hdcp cipher and port */
+	XHdcp1x_PortDisable(InstancePtr);
+	XHdcp1x_CipherDisable(InstancePtr);
+
+	/* Clear statistics */
+	memset(&(InstancePtr->Rx.Stats), 0, sizeof(InstancePtr->Rx.Stats));
+}
+
+/*****************************************************************************/
+/**
+* This function initiates the computations for a receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxStartComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* NextStatePtr not being used */
+	UNUSED(NextStatePtr);
+
+	u8 Buf[8];
+	u64 Value = 0;
+	u32 X = 0;
+	u32 Y = 0;
+	u32 Z = 0;
+
+	/* Log */
+	XHdcp1x_RxDebugLog(InstancePtr, "starting computations");
+
+	/* Update statistics */
+	InstancePtr->Rx.Stats.AuthAttempts++;
+
+	/* Determine theAKsv */
+	memset(Buf, 0, 8);
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_AKSV, Buf,
+			XHDCP1X_PORT_SIZE_AKSV);
+	XHDCP1X_PORT_BUF_TO_UINT(Value, Buf, XHDCP1X_PORT_SIZE_AKSV * 8);
+
+	/* Load the cipher with the remote ksv */
+	XHdcp1x_CipherSetRemoteKsv(InstancePtr, Value);
+
+	/* Update theU64Value with An */
+	memset(Buf, 0, 8);
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_AN, Buf,
+			XHDCP1X_PORT_SIZE_AN);
+	XHDCP1X_PORT_BUF_TO_UINT(Value, Buf, XHDCP1X_PORT_SIZE_AN * 8);
+
+	/* Load the cipher B registers with An */
+	X = (u32)(Value & 0x0FFFFFFFul);
+	Value >>= 28;
+	Y = (u32)(Value & 0x0FFFFFFFul);
+	Value >>= 28;
+	if (InstancePtr->IsRepeater) {
+		Z = (u32)((Value | 0x00000100) & 0x000001FFul);
+	}
+	else {
+		Z = (u32)(Value & 0x000000FFul);
+	}
+	XHdcp1x_CipherSetB(InstancePtr, X, Y, Z);
+
+	/* Initiate the block cipher */
+	XHdcp1x_CipherDoRequest(InstancePtr, XHDCP1X_CIPHER_REQUEST_BLOCK);
+}
+
+/*****************************************************************************/
+/**
+* This function polls the progress of the computations for a state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxPollForComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Check for done */
+	if (XHdcp1x_CipherIsRequestComplete(InstancePtr)) {
+		u8 Buf[4];
+		u16 Ro = 0;
+
+		/* Log */
+		XHdcp1x_RxDebugLog(InstancePtr, "computations complete");
+
+		/* Read theRo */
+		Ro = XHdcp1x_CipherGetRo(InstancePtr);
+
+		/* Initialize Buf */
+		memset(Buf, 0, 4);
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, Ro, 16);
+
+		/* Update the value of Ro' */
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_RO,
+				Buf, 2);
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+		/* No reset required in the sofware for HDMI. KSV fifo
+		 * pointer reset is implemented in the hardware. */
+
+#else
+		u32 KSVPtrReset = 0;
+
+		/* Reset the KSV FIFO read pointer to ox6802C */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_HDCP_RESET_KSV,
+				&KSVPtrReset, 4);
+		KSVPtrReset |= XHDCP1X_PORT_HDCP_RESET_KSV_RST;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_HDCP_RESET_KSV,
+				&KSVPtrReset, 4);
+
+		KSVPtrReset &= ~XHDCP1X_PORT_HDCP_RESET_KSV_RST;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_HDCP_RESET_KSV,
+				&KSVPtrReset, 4);
+
+#if defined(XHDCP1X_PORT_BIT_BSTATUS_RO_AVAILABLE)
+		/* Update the Bstatus to indicate Ro' available */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+				Buf, XHDCP1X_PORT_SIZE_BSTATUS);
+		Buf[0] |= XHDCP1X_PORT_BIT_BSTATUS_RO_AVAILABLE;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+				Buf, XHDCP1X_PORT_SIZE_BSTATUS);
+#endif
+
+#endif
+
+		if (InstancePtr->IsRepeater) {
+			*NextStatePtr = XHDCP1X_STATE_WAITFORDOWNSTREAM;
+			if (InstancePtr->Rx.
+				IsRepeaterDownstreamAuthCallbackSet) {
+				if (InstancePtr->Rx.
+					RepeaterDownstreamAuthCallback
+							!= NULL) {
+				InstancePtr->Rx.RepeaterDownstreamAuthCallback
+				(InstancePtr->Rx.RepeaterDownstreamAuthRef);
+				}
+				else {
+					XHdcp1x_RxDebugLog(InstancePtr,
+					"Warning: Repeater Downstream"
+					"interface not triggered,"
+					"CallBack not Initialized !!!");
+				}
+			}
+		}
+		else {
+			*NextStatePtr = XHDCP1X_STATE_AUTHENTICATED;
+		}
+	}
+	else {
+		XHdcp1x_RxDebugLog(InstancePtr, "waiting for computations");
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the SHA-1 Hash value for the Repeater Rx interface.
+*
+* @param	InstancePtr is the hdcp state machine.
+* @param	RepeaterInfo is the repeater information.
+*
+* @return	Truth value indicating valid (TRUE) or invalid (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_RxCalculateSHA1Value(XHdcp1x *InstancePtr, u16 RepeaterInfo)
+{
+	SHA1Context Sha1Context;
+	u8 Buf[24];
+	u32 NumToRead = 0;
+	int IsValid = FALSE;
+	u32 KsvCount;
+	u64 tempKsv;
+
+	/* Initialize Buf */
+	memset(Buf, 0, 24);
+
+	/* Initialize Sha1Context */
+	SHA1Reset(&Sha1Context);
+
+	/* Assume success */
+	IsValid = TRUE;
+
+	/* Determine theNumToRead */
+	NumToRead = ((RepeaterInfo & 0x7Fu));
+
+	/* Read one ksv at a time from the
+	 * Ksv List and send it to SHA1 Input
+	 */
+	KsvCount = 0;
+
+	while (KsvCount < NumToRead) {
+		if (InstancePtr->RepeaterValues.DeviceCount > 0) {
+			tempKsv = InstancePtr->RepeaterValues.KsvList[KsvCount];
+			XHDCP1X_PORT_UINT_TO_BUF(Buf , tempKsv ,
+					(XHDCP1X_PORT_SIZE_BKSV*8));
+			SHA1Input(&Sha1Context , Buf , XHDCP1X_PORT_SIZE_BKSV);
+		}
+		else {
+			IsValid = FALSE;
+		}
+		KsvCount++;
+	}
+
+	/* Check for success */
+	if (IsValid) {
+		u64 Mo = 0;
+		u8 Sha1Result[SHA1HashSize];
+
+		/* Insert RepeaterInfo into the SHA-1 transform */
+		Buf[0] = (u8) (RepeaterInfo & 0xFFu);
+		Buf[1] = (u8) ((RepeaterInfo >> 8) & 0xFFu);
+		SHA1Input(&Sha1Context, Buf, 2);
+
+		/* Insert the Mo into the SHA-1 transform */
+		Mo = XHdcp1x_CipherGetMo(InstancePtr);
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, Mo, 64);
+
+		SHA1Input(&Sha1Context, Buf, 8);
+
+		/* Finalize the SHA-1 result and confirm success */
+		if (SHA1Result(&Sha1Context, Sha1Result) == shaSuccess) {
+			/* Offset(XHDCP1X_PORT_OFFSET_VH0) = 0 */
+			u8 Offset = 0;
+			const u8 *Sha1Buf = Sha1Result;
+			int NumIterations = (SHA1HashSize >> 2);
+
+			/* Iterate through the SHA-1 chunks */
+			do {
+				u32 CalcValue = 0;
+
+				/* Determine CalcValue */
+				CalcValue = *Sha1Buf++;
+				CalcValue <<= 8;
+				CalcValue |= *Sha1Buf++;
+				CalcValue <<= 8;
+				CalcValue |= *Sha1Buf++;
+				CalcValue <<= 8;
+				CalcValue |= *Sha1Buf++;
+
+				/* Update the V' value in the Instance
+				 * Pointer for the HDCP state machine
+				 */
+				InstancePtr->RepeaterValues.V[Offset]
+					= CalcValue;
+
+				/* Update for loop */
+				Offset++;
+				NumIterations--;
+			}
+			while (NumIterations > 0);
+		}
+		/* Otherwise */
+		else {
+			IsValid = FALSE;
+		}
+	}
+
+	return (IsValid);
+}
+
+/*****************************************************************************/
+/**
+* This function does the necessary actions to update HDCP
+* after the topology has been set.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopologyUpdate(XHdcp1x *InstancePtr)
+{
+	/* Post the re-authentication request */
+	XHdcp1x_RxPostEvent(InstancePtr, XHDCP1X_EVENT_DOWNSTREAMREADY);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the RepeaterInfo value int the HDCP RX instance
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    TopologyPtr is the pointer to topology information.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopology(XHdcp1x *InstancePtr,
+		const XHdcp1x_RepeaterExchange *TopologyPtr)
+{
+	memcpy(&(InstancePtr->RepeaterValues), TopologyPtr,
+			sizeof(XHdcp1x_RepeaterExchange));
+}
+
+/*****************************************************************************/
+/**
+* This function sets the KSVList value(s) in the HDCP RX KSV Fifo register
+* space for the upstream interface to read.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    ListPtr is a pointer to the KSV list.
+* @param    ListSize is the number of KSVs in the list.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopologyKSVList(XHdcp1x *InstancePtr, u8 *ListPtr,
+		u32 ListSize)
+{
+	u32 i;
+
+	for(i=0 ; i<ListSize; i++) {
+		memcpy(&InstancePtr->RepeaterValues.KsvList[i],
+				(ListPtr + (i*5)), XHDCP1X_PORT_SIZE_BKSV);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the Depth value in the HDCP RX BStatus/BInfo register
+* space for the upstream interface to read.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    Value is the Depth value.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopologyDepth(XHdcp1x *InstancePtr, u32 Value)
+{
+	InstancePtr->RepeaterValues.Depth = Value;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the DEVICE_COUNT value in the HDCP RX register space
+* for the upstream interface to read.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    Value is the device count value.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopologyDeviceCnt(XHdcp1x *InstancePtr, u32 Value)
+{
+	InstancePtr->RepeaterValues.DeviceCount = Value;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the MAX_CASCADE_EXCEEDED error flag in the HDCP
+* BStatus/BInfo register to indicate a topology error. Setting the flag
+* indicates a depth of more than (4 - 1).
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    Value is either TRUE or FALSE.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopologyMaxCascadeExceeded(XHdcp1x *InstancePtr, u8 Value)
+{
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+
+	u32 BStatus;
+
+	/* Update the value of Max Devices exceeded in BStatus */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+		&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+	BStatus |= (u32)(Value << XHDCP1X_PORT_BSTATUS_DEPTH_ERR_SHIFT);
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+		&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+
+#else
+
+	u32 BInfo;
+
+	/* Update the value of Depth in BInfo */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+		&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+	BInfo |= (Value << XHDCP1X_PORT_BINFO_DEPTH_ERR_SHIFT);
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+		&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function sets the MAX_DEVS_EXCEEDED error flag in the HDCP
+* BStatus register to indicate a topology error. Setting the flag
+* indicates that more than 31 downstream devices are attached.
+*
+* @param    InstancePtr is a pointer to the Hdcp1x core instance.
+* @param    Value is either TRUE or FALSE.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp1x_RxSetTopologyMaxDevsExceeded(XHdcp1x *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Value == FALSE || Value == TRUE);
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+
+	u16 DevCntErr = (Value & 0xFFFF);
+	u32 BStatus;
+
+	/* Update the value of Max Devices exceeded in BStatus */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+		&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+	BStatus |= (DevCntErr << XHDCP1X_PORT_BSTATUS_DEV_CNT_ERR_SHIFT);
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+		&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+
+#else
+
+	u32 BInfo;
+
+	/* Update the value of Depth in BInfo */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+		&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+	BInfo |= (Value << XHDCP1X_PORT_BINFO_DEV_CNT_ERR_SHIFT);
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+		&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function set the HDMI_MODE in the BStatus register of the HDMI RX DDC
+* space.
+*
+* @param	InstancePtr is a pointer to the Hdcp1x core instance.
+* @param	Value is the truth-value.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp1x_RxSetHdmiMode(XHdcp1x *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+	u32 BStatus;
+
+	/* Update the value of HDMI_MODE bit in the BStatus Register */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+		&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+	if (Value == TRUE) {
+		BStatus |= XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE;
+	} else {
+		BStatus &= ~XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE;
+	}
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+		&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+#else
+	UNUSED(Value);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function writes the KSV List and the BInfo values to the RX
+* DPCD register space and sets the READY bit.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxAssembleKSVList(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(NextStatePtr != NULL);
+
+	/* Check if the max cascade and max depth is not exceeded */
+	if (InstancePtr->RepeaterValues.Depth > XHDCP1X_RPTR_MAX_CASCADE) {
+		XHdcp1x_RxDebugLog(InstancePtr, "Repeater maximum\
+						cascade exceeded");
+		*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+	}
+	else if (InstancePtr->RepeaterValues.DeviceCount >
+				XHDCP1X_RPTR_MAX_DEVS_COUNT) {
+		XHdcp1x_RxDebugLog(InstancePtr, "Repeater maximum\
+						Depth exceeded");
+		*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+	}
+	else {
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+		u32 BCaps;
+#else
+		u32 BInfo;
+		u32 KSVPtrReset;
+#endif
+
+		u32 BStatus;
+		u8 Buf[5];
+		u8 Buf_full[XHDCP1X_PORT_SIZE_BKSV * XHDCP1X_RPTR_MAX_DEVS_COUNT];
+		u32 sha1value;
+		u32 ksvCount, ksvsToWrite;
+		u16 RepeaterInfo = 0;
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+
+		/* Ensure that the READY bit is clear */
+		/* Update the Ready bit in the BCaps Register */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+				&BCaps, XHDCP1X_PORT_SIZE_BCAPS);
+		if(BCaps & XHDCP1X_PORT_BIT_BCAPS_READY) {
+			BCaps &= ~XHDCP1X_PORT_BIT_BCAPS_READY;
+			XHdcp1x_PortWrite(InstancePtr,
+				XHDCP1X_PORT_OFFSET_BCAPS ,
+				&BCaps, XHDCP1X_PORT_SIZE_BCAPS);
+		}
+
+		/* Update the value of Depth and Device count in BStatus */
+		memset(Buf,0,5);
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+			&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+		BStatus |= ((InstancePtr->RepeaterValues.Depth<<8) & 0x0700);
+		BStatus |= ((InstancePtr->RepeaterValues.DeviceCount) & 0x007F);
+		BStatus |= XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+			&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+
+#else
+		/* Update the value of Depth in BInfo */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+		BInfo |= ((InstancePtr->RepeaterValues.Depth<<8) & 0x0700);
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+
+		/*Update the value of Device Count in the BInfo register */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+		BInfo |= ((InstancePtr->RepeaterValues.DeviceCount) & 0x007F);
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&BInfo, XHDCP1X_PORT_SIZE_BINFO);
+#endif
+		/* Update the KSV List in the KSV Fifo */
+		ksvsToWrite = InstancePtr->RepeaterValues.DeviceCount;
+		ksvCount = 0;
+		while(ksvsToWrite>0) {
+			u64 tempKsv;
+			memset(Buf,0,5);
+			tempKsv = InstancePtr->RepeaterValues.KsvList[ksvCount];
+			XHDCP1X_PORT_UINT_TO_BUF(Buf, tempKsv ,
+					(XHDCP1X_PORT_SIZE_BKSV * 8));
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+
+			/* Write the KSV to the HDCP_DAT register each time,
+			 * The KSV Fifo will auto increment
+			 */
+			XHdcp1x_PortWrite(InstancePtr,
+					XHDCP1X_PORT_OFFSET_KSVFIFO,
+					Buf, XHDCP1X_PORT_SIZE_BKSV);
+
+#else
+			memcpy((Buf_full + (ksvCount * XHDCP1X_PORT_SIZE_BKSV)),
+					Buf, XHDCP1X_PORT_SIZE_BKSV);
+
+			if (ksvsToWrite == 1) {
+				XHdcp1x_PortWrite(InstancePtr,
+					XHDCP1X_PORT_OFFSET_KSVFIFO,
+					Buf_full,
+					(InstancePtr->RepeaterValues.DeviceCount *
+					 XHDCP1X_PORT_SIZE_BKSV));
+			}
+#endif
+			ksvCount++;
+			ksvsToWrite -= 1;
+		}
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+		RepeaterInfo = (XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE) |
+				(XHDCP1X_PORT_BSTATUS_BIT_DEPTH_NO_ERR) |
+			(InstancePtr->RepeaterValues.Depth <<
+					XHDCP1X_PORT_BSTATUS_DEPTH_SHIFT) |
+			(XHDCP1X_PORT_BSTATUS_BIT_DEV_CNT_NO_ERR) |
+			(InstancePtr->RepeaterValues.DeviceCount &
+					XHDCP1X_PORT_BSTATUS_DEV_CNT_MASK);
+#else
+		RepeaterInfo = (XHDCP1X_PORT_BINFO_BIT_DEPTH_NO_ERR) |
+			(InstancePtr->RepeaterValues.Depth <<
+					XHDCP1X_PORT_BINFO_DEPTH_SHIFT) |
+			(XHDCP1X_PORT_BINFO_BIT_DEV_CNT_NO_ERR) |
+			(InstancePtr->RepeaterValues.DeviceCount &
+					XHDCP1X_PORT_BINFO_DEV_CNT_MASK);
+#endif
+
+		XHdcp1x_RxCalculateSHA1Value(InstancePtr,RepeaterInfo);
+
+#if (defined(XPAR_XV_HDMIRX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMIRX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMIRX1_NUM_INSTANCES > 0))
+
+		/* Update the value of V'H0 */
+		sha1value = 0;
+		sha1value = InstancePtr->RepeaterValues.V[0];
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, sha1value ,
+					(XHDCP1X_PORT_SIZE_VH0 * 8));
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH0,
+				Buf, XHDCP1X_PORT_SIZE_VH0);
+
+		/* Update the value of V'H1 */
+		sha1value = InstancePtr->RepeaterValues.V[1];
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, sha1value ,
+					(XHDCP1X_PORT_SIZE_VH1 * 8));
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH1,
+				Buf, XHDCP1X_PORT_SIZE_VH1);
+
+		/* Update the value of V'H2 */
+		sha1value = InstancePtr->RepeaterValues.V[2];
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, sha1value ,
+					(XHDCP1X_PORT_SIZE_VH2 * 8));
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH2,
+				Buf , XHDCP1X_PORT_SIZE_VH2);
+
+		/* Update the value of V'H3 */
+		sha1value = InstancePtr->RepeaterValues.V[3];
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, sha1value ,
+					(XHDCP1X_PORT_SIZE_VH3 * 8));
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH3,
+				Buf , XHDCP1X_PORT_SIZE_VH3);
+
+		/* Update the value of V'H4 */
+		sha1value = InstancePtr->RepeaterValues.V[4];
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, sha1value ,
+					(XHDCP1X_PORT_SIZE_VH4 * 8));
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH4,
+				Buf, XHDCP1X_PORT_SIZE_VH4);
+
+		/* Update the Ready bit in the BCaps Register */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS,
+				&BCaps, XHDCP1X_PORT_SIZE_BCAPS);
+		BCaps |= XHDCP1X_PORT_BIT_BCAPS_READY;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BCAPS ,
+				&BCaps, XHDCP1X_PORT_SIZE_BCAPS);
+
+#else
+
+		/* Update the value of V'H0 */
+		sha1value = 0;
+		sha1value = InstancePtr->RepeaterValues.V[0];
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH0,
+				&sha1value, XHDCP1X_PORT_SIZE_VH0);
+
+		/* Update the value of V'H1 */
+		sha1value = InstancePtr->RepeaterValues.V[1];
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH1,
+				&sha1value, XHDCP1X_PORT_SIZE_VH1);
+
+		/* Update the value of V'H2 */
+		sha1value = InstancePtr->RepeaterValues.V[2];
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH2,
+				&sha1value , XHDCP1X_PORT_SIZE_VH2);
+
+		/* Update the value of V'H3 */
+		sha1value = InstancePtr->RepeaterValues.V[3];
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH3,
+				&sha1value , XHDCP1X_PORT_SIZE_VH3);
+
+		/* Update the value of V'H4 */
+		sha1value = InstancePtr->RepeaterValues.V[4];
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_VH4,
+				&sha1value, XHDCP1X_PORT_SIZE_VH4);
+
+		/* Reset the KSV FIFO read pointer to ox6802C */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_HDCP_RESET_KSV,
+			&KSVPtrReset, XHDCP1X_PORT_SIZE_HDCP_RESET_KSV);
+		KSVPtrReset |= XHDCP1X_PORT_HDCP_RESET_KSV_RST;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_HDCP_RESET_KSV,
+			&KSVPtrReset, XHDCP1X_PORT_SIZE_HDCP_RESET_KSV);
+
+		KSVPtrReset &= ~XHDCP1X_PORT_HDCP_RESET_KSV_RST;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_HDCP_RESET_KSV,
+			&KSVPtrReset, XHDCP1X_PORT_SIZE_HDCP_RESET_KSV);
+
+		/* Update the Ready bit in the BStatus Register */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+				&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+		BStatus |= XHDCP1X_PORT_BIT_BSTATUS_READY;
+		XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS ,
+				&BStatus, XHDCP1X_PORT_SIZE_BSTATUS);
+#endif
+
+		*NextStatePtr = XHDCP1X_STATE_AUTHENTICATED;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function updates the Ro'/Ri' register of the state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		This function has to save the value of Ri (in RememberRi) as
+*		the macro that converts from a uint16 to a HDCP buffer
+*		destroys the original value.
+*
+******************************************************************************/
+static void XHdcp1x_RxUpdateRi(XHdcp1x *InstancePtr)
+{
+	char LogBuf[20];
+	u8 Buf[4];
+	u16 Ri = 0;
+	u16 RememberRi = 0;
+
+	/* Read Ri */
+	Ri = XHdcp1x_CipherGetRi(InstancePtr);
+
+	/* Update RememberRi */
+	RememberRi = Ri;
+
+	/* Initialize theBuf */
+	memset(Buf, 0, 4);
+	XHDCP1X_PORT_UINT_TO_BUF(Buf, Ri, XHDCP1X_PORT_SIZE_RO * 8);
+
+	/* Update the value of Ro' */
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_RO,
+			Buf, sizeof(Ri));
+
+#if defined(XHDCP1X_PORT_BIT_BSTATUS_RO_AVAILABLE)
+	/* Update the Bstatus to indicate Ro' available */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS, Buf,
+			XHDCP1X_PORT_SIZE_BSTATUS);
+	Buf[0] |= XHDCP1X_PORT_BIT_BSTATUS_RO_AVAILABLE;
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS, Buf,
+			XHDCP1X_PORT_SIZE_BSTATUS);
+#endif
+
+	/* Update statistics */
+	InstancePtr->Rx.Stats.RiUpdates++;
+
+	/* Determine theLogBuf */
+	snprintf(LogBuf, 20, "update Ri (%04X)", RememberRi);
+
+	/* Log */
+	XHdcp1x_RxDebugLog(InstancePtr, LogBuf);
+}
+
+/*****************************************************************************/
+/**
+* This functions handles check the integrity of the link.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxCheckLinkIntegrity(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	if (XHdcp1x_CipherIsLinkUp(InstancePtr)) {
+		*NextStatePtr = XHDCP1X_STATE_AUTHENTICATED;
+	}
+	else {
+		*NextStatePtr = XHDCP1X_STATE_LINKINTEGRITYFAILED;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This functions handles check if the encryption status (enable/disable) of
+* the HDCP cipher has changed.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxCheckEncryptionChange(XHdcp1x *InstancePtr)
+{
+	InstancePtr->Rx.XORState.PreviousState =
+			InstancePtr->Rx.XORState.CurrentState;
+
+	InstancePtr->Rx.XORState.CurrentState =
+			XHdcp1x_CipherXorInProgress(InstancePtr);
+
+	/* Check if encrypted */
+	if (InstancePtr->Rx.XORState.CurrentState !=
+			InstancePtr->Rx.XORState.PreviousState) {
+		/* Call encryption update callback */
+		if (InstancePtr->Rx.IsEncryptionUpdateCallbackSet) {
+			InstancePtr->Rx.EncryptionUpdateCallback(
+			InstancePtr->Rx.EncryptionUpdateCallbackRef);
+		}
+	}
+
+	/* Start a 2 second timer again */
+	XHdcp1x_RxStartTimer(InstancePtr, (2 * XVPHY_TMO_1SECOND));
+}
+
+/*****************************************************************************/
+/**
+* This functions reports the failure of link integrity.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxReportLinkIntegrityFailure(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* NextStatePtr not being used */
+	UNUSED(NextStatePtr);
+
+#if defined(XHDCP1X_PORT_BIT_BSTATUS_LINK_FAILURE)
+	u8 Buf[XHDCP1X_PORT_SIZE_BSTATUS];
+
+	/* Update the Bstatus register */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS, Buf,
+			XHDCP1X_PORT_SIZE_BSTATUS);
+	Buf[0] |= XHDCP1X_PORT_BIT_BSTATUS_LINK_FAILURE;
+	XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS, Buf,
+			XHDCP1X_PORT_SIZE_BSTATUS);
+#endif
+
+	/* Log */
+	XHdcp1x_RxDebugLog(InstancePtr, "link integrity failed");
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "disabled" state of the receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunDisabledState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For enable */
+		case XHDCP1X_EVENT_ENABLE:
+			*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+			if ((InstancePtr->Rx.Flags & XVPHY_FLAG_PHY_UP) == 0) {
+				*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			}
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			InstancePtr->Rx.Flags &= ~XVPHY_FLAG_PHY_UP;
+			break;
+
+		/* For physical layer up */
+		case XHDCP1X_EVENT_PHYUP:
+			InstancePtr->Rx.Flags |= XVPHY_FLAG_PHY_UP;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "unauthenticated" state of the receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunUnauthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_COMPUTATIONS;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "computations" state of the receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunComputationsState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			XHdcp1x_RxStartComputations(InstancePtr,
+					NextStatePtr);
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For poll */
+		case XHDCP1X_EVENT_POLL:
+			XHdcp1x_RxPollForComputations(InstancePtr,
+					NextStatePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "wait for downstream" state of the receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunWaitForDownstreamState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_COMPUTATIONS;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For timeout event */
+		case XHDCP1X_EVENT_TIMEOUT:
+			*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+			break;
+
+		case XHDCP1X_EVENT_DOWNSTREAMREADY:
+			*NextStatePtr = XHDCP1X_STATE_ASSEMBLEKSVLIST;
+			break;
+
+		case XHDCP1X_EVENT_NULL:
+			/*Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_CHECK:
+			/*Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_ENABLE:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_PHYUP:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_POLL:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_UPDATERi:
+			/* Do nothing */
+			break;
+
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "assemble KSV list" state of the receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunAssembleKsvListState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		case XHDCP1X_EVENT_NULL:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_CHECK:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_ENABLE:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_PHYUP:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_POLL:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_UPDATERi:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_TIMEOUT:
+			/* Do nothing */
+			break;
+
+		case XHDCP1X_EVENT_DOWNSTREAMREADY:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "authenticated" state of the receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunAuthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_COMPUTATIONS;
+			break;
+
+		/* For check */
+		case XHDCP1X_EVENT_CHECK:
+			XHdcp1x_RxCheckLinkIntegrity(InstancePtr,
+					NextStatePtr);
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For update Ri */
+		case XHDCP1X_EVENT_UPDATERi:
+			XHdcp1x_RxUpdateRi(InstancePtr);
+			break;
+
+		/* In every 2 second priodically checks encryption status */
+		case XHDCP1X_EVENT_TIMEOUT:
+			XHdcp1x_RxCheckEncryptionChange(InstancePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "link integrity failed" state of the receiver state
+* machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunLinkIntegrityFailedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_COMPUTATIONS;
+			break;
+
+		/* For check */
+		case XHDCP1X_EVENT_CHECK:
+			XHdcp1x_RxCheckLinkIntegrity(InstancePtr,
+					NextStatePtr);
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "physical layer down" state of the receiver state
+* machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxRunPhysicalLayerDownState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer up */
+		case XHDCP1X_EVENT_PHYUP:
+			*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function enters a HDCP receiver state.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	State is the state to enter.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxEnterState(XHdcp1x *InstancePtr, XHdcp1x_StateType State,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of state called */
+	switch (State) {
+		/* For the disabled state */
+		case XHDCP1X_STATE_DISABLED:
+			XHdcp1x_RxDisableState(InstancePtr);
+			break;
+
+		/* For the unauthenticated state */
+		case XHDCP1X_STATE_UNAUTHENTICATED:
+			XHdcp1x_RxSetCheckLinkState(InstancePtr, FALSE);
+			InstancePtr->Rx.Flags |= XVPHY_FLAG_PHY_UP;
+			if (InstancePtr->Rx.IsUnauthenticatedCallbackSet) {
+				InstancePtr->Rx.UnauthenticatedCallback(
+				InstancePtr->Rx.UnauthenticatedCallbackRef);
+			}
+			break;
+
+		/* For the computations state */
+		case XHDCP1X_STATE_COMPUTATIONS:
+			XHdcp1x_RxStartComputations(InstancePtr,
+						NextStatePtr);
+			break;
+
+		/* For the wait-for-downstream state */
+		case XHDCP1X_STATE_WAITFORDOWNSTREAM:
+			XHdcp1x_RxSetCheckLinkState(InstancePtr, TRUE);
+			XHdcp1x_RxStartTimer(InstancePtr,
+			((5 * XVPHY_TMO_1SECOND) + (5 * XVPHY_TMO_100MS)) );
+			break;
+
+		/* For assemble KSV list */
+		case XHDCP1X_STATE_ASSEMBLEKSVLIST:
+			XHdcp1x_RxAssembleKSVList(InstancePtr,
+						NextStatePtr);
+			break;
+
+		/* For the authenticated state */
+		case XHDCP1X_STATE_AUTHENTICATED:
+			XHdcp1x_RxDebugLog(InstancePtr, "authenticated");
+			XHdcp1x_RxSetCheckLinkState(InstancePtr, TRUE);
+			if(InstancePtr->Rx.IsAuthenticatedCallbackSet) {
+				InstancePtr->Rx.AuthenticatedCallback(
+				InstancePtr->Rx.AuthenticatedCallbackRef);
+			}
+			XHdcp1x_RxStartTimer(InstancePtr,
+					(2 * XVPHY_TMO_1SECOND));
+			break;
+
+		/* For the link integrity failed state */
+		case XHDCP1X_STATE_LINKINTEGRITYFAILED:
+			InstancePtr->Rx.Stats.LinkFailures++;
+			XHdcp1x_RxReportLinkIntegrityFailure(InstancePtr,
+					NextStatePtr);
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_STATE_PHYDOWN:
+			InstancePtr->Rx.Flags &= ~XVPHY_FLAG_PHY_UP;
+			XHdcp1x_CipherDisable(InstancePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function exits a HDCP receiver state.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	State is the state to exit.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxExitState(XHdcp1x *InstancePtr, XHdcp1x_StateType State)
+{
+	/* Case-wise process the kind of state called */
+	switch (State) {
+		/* For the disabled state */
+		case XHDCP1X_STATE_DISABLED:
+			XHdcp1x_RxEnableState(InstancePtr);
+			break;
+
+		/* For the authenticated state */
+		case XHDCP1X_STATE_AUTHENTICATED:
+			XHdcp1x_RxStopTimer(InstancePtr);
+			XHdcp1x_RxSetCheckLinkState(InstancePtr, FALSE);
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_STATE_PHYDOWN:
+			XHdcp1x_CipherEnable(InstancePtr);
+			break;
+
+		/* For wait-for-downstream ready */
+		case XHDCP1X_STATE_WAITFORDOWNSTREAM:
+			XHdcp1x_RxStopTimer(InstancePtr);
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function drives a HDCP receiver state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	Event is the event to process.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxDoTheState(XHdcp1x *InstancePtr, XHdcp1x_EventType Event)
+{
+	XHdcp1x_StateType NextState = InstancePtr->Rx.CurrentState;
+
+	/* Case-wise process the kind of state called */
+	switch (InstancePtr->Rx.CurrentState) {
+		/* For the disabled state */
+		case XHDCP1X_STATE_DISABLED:
+			XHdcp1x_RxRunDisabledState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the unauthenticated state */
+		case XHDCP1X_STATE_UNAUTHENTICATED:
+			XHdcp1x_RxRunUnauthenticatedState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the computations state */
+		case XHDCP1X_STATE_COMPUTATIONS:
+			XHdcp1x_RxRunComputationsState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the Wait For Downstream state */
+		case XHDCP1X_STATE_WAITFORDOWNSTREAM:
+			XHdcp1x_RxRunWaitForDownstreamState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the assemble ksv list state */
+		case XHDCP1X_STATE_ASSEMBLEKSVLIST:
+			XHdcp1x_RxRunAssembleKsvListState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the authenticated state */
+		case XHDCP1X_STATE_AUTHENTICATED:
+			XHdcp1x_RxRunAuthenticatedState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the link integrity failed state */
+		case XHDCP1X_STATE_LINKINTEGRITYFAILED:
+			XHdcp1x_RxRunLinkIntegrityFailedState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* For the physical layer down state */
+		case XHDCP1X_STATE_PHYDOWN:
+			XHdcp1x_RxRunPhysicalLayerDownState(InstancePtr,
+					Event, &NextState);
+			break;
+
+		/* Otherwise */
+		default:
+			break;
+	}
+
+	/* Check for state change */
+	while (InstancePtr->Rx.CurrentState != NextState) {
+		/* Perform the state transition */
+		XHdcp1x_RxExitState(InstancePtr,
+				InstancePtr->Rx.CurrentState);
+		InstancePtr->Rx.PreviousState = InstancePtr->Rx.CurrentState;
+		InstancePtr->Rx.CurrentState = NextState;
+		XHdcp1x_RxEnterState(InstancePtr,
+				InstancePtr->Rx.CurrentState,
+				&NextState);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function processes the events pending on a state machine.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_RxProcessPending(XHdcp1x *InstancePtr)
+{
+	/* Check for any pending events */
+	if (InstancePtr->Rx.PendingEvents != 0) {
+		u16 Pending = InstancePtr->Rx.PendingEvents;
+		XHdcp1x_EventType Event = XHDCP1X_EVENT_NULL;
+
+		/* Update InstancePtr */
+		InstancePtr->Rx.PendingEvents = 0;
+
+		/* Iterate through thePending */
+		do {
+			/* Check for a pending event */
+			if ((Pending & 1u) != 0) {
+				XHdcp1x_RxDoTheState(InstancePtr, Event);
+			}
+
+			/* Update for loop */
+			Pending >>= 1;
+			Event++;
+		}
+		while (Pending != 0);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function converts from a state to a display string.
+*
+* @param	State is the state to convert.
+*
+* @return	The corresponding display string.
+*
+* @note		None.
+*
+******************************************************************************/
+static const char *XHdcp1x_RxStateToString(XHdcp1x_StateType State)
+{
+	const char *String = NULL;
+
+	/* Case-wise process the input state */
+	switch (State) {
+		case XHDCP1X_STATE_DISABLED:
+			String = "disabled";
+			break;
+
+		case XHDCP1X_STATE_UNAUTHENTICATED:
+			String = "unauthenticated";
+			break;
+
+		case XHDCP1X_STATE_COMPUTATIONS:
+			String = "computations";
+			break;
+
+		case XHDCP1X_STATE_WAITFORDOWNSTREAM:
+			String = "wait-for-downstream";
+			break;
+
+		case XHDCP1X_STATE_ASSEMBLEKSVLIST:
+			String = "assemble-ksv-list";
+			break;
+
+		case XHDCP1X_STATE_AUTHENTICATED:
+			String = "authenticated";
+			break;
+
+		case XHDCP1X_STATE_LINKINTEGRITYFAILED:
+			String = "link-integrity-failed";
+			break;
+
+		case XHDCP1X_STATE_PHYDOWN:
+			String = "physical-layer-down";
+			break;
+
+		default:
+			String = "unknown?";
+			break;
+	}
+
+	return (String);
+}
+
+#if XHDCP1X_ADDITIONAL_DEBUG
+/*****************************************************************************/
+/**
+* This function converts from a event to a display string.
+*
+* @param	Event is the event to convert.
+*
+* @return	The corresponding display string.
+*
+* @note		None.
+*
+******************************************************************************/
+static const char *XHdcp1x_RxEventToString(XHdcp1x_EventType Event)
+{
+	const char *String = NULL;
+
+	/* Case-wise process the input event */
+	switch (Event) {
+		case XHDCP1X_EVENT_NULL:
+			String = "null";
+			break;
+
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			String = "authenticate";
+			break;
+
+		case XHDCP1X_EVENT_CHECK:
+			String = "check";
+			break;
+
+		case XHDCP1X_EVENT_DISABLE:
+			String = "disable";
+			break;
+
+		case XHDCP1X_EVENT_ENABLE:
+			String = "enable";
+			break;
+
+		case XHDCP1X_EVENT_PHYDOWN:
+			String = "phy-down";
+			break;
+
+		case XHDCP1X_EVENT_PHYUP:
+			String = "phy-up";
+			break;
+
+		case XHDCP1X_EVENT_POLL:
+			String = "poll";
+			break;
+
+		case XHDCP1X_EVENT_UPDATERi:
+			String = "update-ri";
+			break;
+
+		case XHDCP1X_EVENT_DOWNSTREAMREADY:
+			String = "downstream-ready";
+			break;
+
+		default:
+			String = "unknown?";
+			break;
+	}
+
+	return (String);
+}
+#endif
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_rx.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_rx.h
@@ -0,0 +1,125 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_rx.h
+* @{
+*
+* This file provides the interface of the HDCP RX state machine
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 1.10  MG     01/18/16 Added function XHdcp1x_RxIsEnabled and
+*                       XHdcp1x_RxIsInProgress.
+* 1.20  MG     02/25/16 Added function XHdcp1x_RxSetCallback.
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added functions:
+*                       XHdcp1x_RxDownstreamReady, XHdcp1x_RxGetRepeaterInfo,
+*                       XHdcp1x_RxDownstreamReadyCallback,
+*                       XHdcp1x_RxSetCallBack.
+* 3.1   yas    07/28/16 Repeater functionality extended to support HDMI.
+*                       Removed the XHdcp1x_RxDownstreamReadyCallback.
+*                       Added fucntions,
+*                       XHdcp1x_RxSetRepeaterBcaps,XHdcp1x_RxIsInComputations,
+*                       XHdcp1x_RxIsInWaitforready, XHdcp1x_RxHandleTimeout,
+*                       XHdcp1x_RxStartTimer, XHdcp1x_RxStopTimer,
+*                       XHdcp1x_RxBusyDelay, XHdcp1x_RxSetTopologyUpdate,
+*                       XHdcp1x_RxSetTopology, XHdcp1x_RxSetTopologyKSVList,
+*                       XHdcp1x_RxSetTopologyDepth,
+*                       XHdcp1x_RxSetTopologyDeviceCnt,
+*                       XHdcp1x_RxSetTopologyMaxCascadeExceeded,
+*                       XHdcp1x_RxSetTopologyMaxDevsExceeded,
+*                       XHdcp1x_RxCheckEncryptionChange.
+* 4.1   yas    11/10/16 Added function XHdcp1x_RxSetHdmiMode.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_RX_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_RX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+
+#include "xstatus.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Prototypes ******************************/
+
+void XHdcp1x_RxInit(XHdcp1x *InstancePtr);
+void XHdcp1x_RxLoadBksvToBuf(XHdcp1x *InstancePtr);
+int XHdcp1x_RxSetCallback(XHdcp1x *InstancePtr,
+		XHdcp1x_HandlerType HandlerType, void *CallbackFunc,
+		void *CallbackRef);
+
+int XHdcp1x_RxPoll(XHdcp1x *InstancePtr);
+int XHdcp1x_RxSetRepeaterBcaps(XHdcp1x *InstancePtr, u8 IsRptr);
+
+int XHdcp1x_RxReset(XHdcp1x *InstancePtr);
+int XHdcp1x_RxEnable(XHdcp1x *InstancePtr);
+int XHdcp1x_RxDisable(XHdcp1x *InstancePtr);
+
+int XHdcp1x_RxSetPhysicalState(XHdcp1x *InstancePtr, int IsUp);
+int XHdcp1x_RxSetLaneCount(XHdcp1x *InstancePtr, int LaneCount);
+int XHdcp1x_RxDownstreamReady(XHdcp1x *InstancePtr);
+int XHdcp1x_RxAuthenticate(XHdcp1x *InstancePtr);
+int XHdcp1x_RxIsAuthenticated(const XHdcp1x *InstancePtr);
+int XHdcp1x_RxIsInComputations(const XHdcp1x *InstancePtr);
+int XHdcp1x_RxIsInWaitforready(const XHdcp1x *InstancePtr);
+int XHdcp1x_RxIsEnabled(const XHdcp1x *InstancePtr);
+int XHdcp1x_RxIsInProgress(const XHdcp1x *InstancePtr);
+
+u64 XHdcp1x_RxGetEncryption(const XHdcp1x *InstancePtr);
+
+void XHdcp1x_RxHandleTimeout(XHdcp1x *InstancePtr);
+int XHdcp1x_RxInfo(const XHdcp1x *InstancePtr);
+int XHdcp1x_RxGetRepeaterInfo(XHdcp1x *InstancePtr,
+		XHdcp1x_RepeaterExchange *RepeaterInfoPtr);
+
+void XHdcp1x_RxSetTopologyMaxDevsExceeded(XHdcp1x *InstancePtr, u8 Value);
+void XHdcp1x_RxSetTopologyMaxCascadeExceeded(XHdcp1x *InstancePtr, u8 Value);
+void XHdcp1x_RxSetTopologyDeviceCnt(XHdcp1x *InstancePtr, u32 Value);
+void XHdcp1x_RxSetTopologyDepth(XHdcp1x *InstancePtr, u32 Value);
+void XHdcp1x_RxSetTopologyKSVList(XHdcp1x *InstancePtr, u8 *ListPtr,
+		u32 ListSize);
+void XHdcp1x_RxSetTopologyUpdate(XHdcp1x *InstancePtr);
+void XHdcp1x_RxSetTopology(XHdcp1x *InstancePtr,
+		const XHdcp1x_RepeaterExchange *TopologyPtr);
+void XHdcp1x_RxSetHdmiMode(XHdcp1x *InstancePtr, u8 Value);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_RX_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_selftest.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_selftest.c
@@ -0,0 +1,98 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_selftest.c
+* @{
+*
+* This file contains self test function for the hdcp interface
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+#include "xhdcp1x_debug.h"
+#include "xhdcp1x_port.h"
+#include "xil_types.h"
+
+#include "xstatus.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Extern Declarations ******************************/
+
+/************************** Global Declarations ******************************/
+
+/*****************************************************************************/
+/**
+* This function self tests an HDCP interface.
+*
+* @param	InstancePtr is the interface to test.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_SelfTest(XHdcp1x *InstancePtr)
+{
+	const XHdcp1x_Config *CfgPtr = &InstancePtr->Config;
+	u32 RegVal;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Confirm that the version is reasonable. */
+	RegVal = XHdcp1x_ReadReg(CfgPtr->BaseAddress,
+			XHDCP1X_CIPHER_REG_VERSION);
+	if (!RegVal || (RegVal == ((u32)(-1)))) {
+		return (XST_FAILURE);
+	}
+
+	/* Confirm that the direction matches in both SW and HW. */
+	if ((!CfgPtr->IsRx && XHdcp1x_IsRX(InstancePtr)) ||
+			(CfgPtr->IsRx && XHdcp1x_IsTX(InstancePtr))) {
+		return (XST_FAILURE);
+	}
+
+	/* Confirm that the protocol matches in both SW and HW. */
+	if ((!CfgPtr->IsHDMI && XHdcp1x_IsHDMI(InstancePtr)) ||
+			(CfgPtr->IsHDMI && XHdcp1x_IsDP(InstancePtr))) {
+		return (XST_FAILURE);
+	}
+
+	return (XST_SUCCESS);
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_sinit.c
@@ -0,0 +1,88 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_sinit.c
+* @{
+*
+* This file contains static initialization method for Xilinx HDCP driver
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+
+
+/************************** Constant Definitions *****************************/
+
+#ifndef XPAR_XHDCP_NUM_INSTANCES
+#define XPAR_XHDCP_NUM_INSTANCES 0	/**< Number of HDCP Instances */
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+
+extern XHdcp1x_Config XHdcp1x_ConfigTable[];	/**< Instance of Lookup table
+						  *  of HDCP instance(s) in
+						  *  the design */
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function returns a reference to an XHdcp1x_Config structure based on
+* specified device ID.
+*
+* @param	DeviceId is the unique core ID of the HDCP interface.
+*
+* @return	A reference to the config record in the configuration table (in
+*		xhdcp_g.c) corresponding the specified DeviceId. NULL if no
+*		match is found.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdcp1x_Config *XHdcp1x_LookupConfig(u16 DeviceId)
+{
+	XHdcp1x_Config *CfgPtr = NULL;
+	u32 Index;
+
+	for (Index = 0; Index < XPAR_XHDCP_NUM_INSTANCES; Index++) {
+		if (XHdcp1x_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XHdcp1x_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return (CfgPtr);
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_tx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_tx.c
@@ -0,0 +1,3748 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_tx.c
+* @{
+*
+* This contains the main implementation file for the Xilinx HDCP transmit
+* state machine
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 1.10  MG     01/18/16 Added function XHdcp1x_TxIsEnabled.
+* 1.20  MG     02/25/16 Added function XHdcp1x_TxSetCallback and
+*                       authenticated callback.
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added enum XHDCP1X_EVENT_READDOWNSTREAM, of
+*                       XHdcp1x_EventType.
+*                       Added new functions:
+*                       XHdcp1x_TxReadDownstream, XHdcp1x_TxSetCallBack,
+*                       XHdcp1x_TxTriggerDownstreamAuth,
+*                       XHdcp1x_TxSetRepeaterInfo.
+* 3.1   yas    06/15/16 Repeater functionality extended to support HDMI.
+*                       Added fucntions,
+*                       XHdcp1x_TxIsInComputations,XHdcp1x_TxIsInWaitforready,
+*                       XHdcp1x_TxIsDownstrmCapable, XHdcp1x_TxIsRepeater,
+*                       XHdcp1x_TxEnableBlank, XHdcp1x_TxDisableBlank,
+*                       XHdcp1x_TxGetTopologyKSVList,
+*                       XHdcp1x_TxGetTopologyDepth,
+*                       XHdcp1x_TxGetTopologyDeviceCnt,
+*                       XHdcp1x_TxGetTopologyMaxCascadeExceeded,
+*                       XHdcp1x_TxGetTopologyBKSV,
+*                       XHdcp1x_TxGetTopologyMaxDevsExceeded,
+*                       XHdcp1x_TxGetTopology
+* 4.1   yas    03/07/17 Updated to remove compliance failures.
+* 4.1   yas    22/04/17 Added function XHdcp1x_TxSetHdmiMode.
+* 4.1   MH     11/05/17 Update to enable encryption immediately after Ro' check.
+*                       Increase timeout for topology propagation.
+* 4.1   yas    08/03/17 Updated the XHdcp1x_TxIsInProgress to track any
+*                       pending authentication requests.
+* 4.2   yas    08/14/18 Updated the XHdcp1x_TxPollForWaitForReady function to
+*                       ready topology in case of a topology error, and make
+*                       it available in XHdcp1x_TxGetTopology().
+*                       Updating the XHdcp1x_TxReset() to clear the
+*                       Authentication Request flag.
+* </pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files *********************************/
+
+
+#include "sha1.h"
+//#include <stdio.h>
+//#include <stdlib.h>
+#include <linux/string.h>
+#include "xhdcp1x.h"
+#include "xhdcp1x_cipher.h"
+#include "xhdcp1x_debug.h"
+#include "xhdcp1x_platform.h"
+#include "xhdcp1x_port.h"
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+#include "xhdcp1x_port_hdmi.h"
+#else
+#include "xhdcp1x_port_dp.h"
+#endif
+#include "xhdcp1x_tx.h"
+#include "xil_types.h"
+#include "xil_printf.h"
+
+/************************** Constant Definitions *****************************/
+
+#define XVPHY_FLAG_PHY_UP	(1u << 0)  /**< Flag to track physical state */
+#define XVPHY_FLAG_IS_REPEATER	(1u << 1)  /**< Flag to track repeater state */
+
+#define XVPHY_TMO_5MS		(5u)    /**< Timeout value for 5ms */
+#define XVPHY_TMO_100MS		(100u)    /**< Timeout value for 100ms */
+#define XVPHY_TMO_1SECOND	(1000u)    /**< Timeout value for 1s */
+
+#define XHDCP1X_MAX_BCAPS_RDY_POLL_CNT	(55) /**< Max times to poll on BCaps
+					  *  Ready bit at 100ms interval */
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * This enumerates the Event Types for HDCP Transmitter state machine.
+ */
+typedef enum {
+	XHDCP1X_EVENT_NULL,
+	XHDCP1X_EVENT_AUTHENTICATE,
+	XHDCP1X_EVENT_CHECK,
+	XHDCP1X_EVENT_DISABLE,
+	XHDCP1X_EVENT_ENABLE,
+	XHDCP1X_EVENT_LINKDOWN,
+	XHDCP1X_EVENT_PHYDOWN,
+	XHDCP1X_EVENT_PHYUP,
+	XHDCP1X_EVENT_POLL,
+	XHDCP1X_EVENT_TIMEOUT,
+	XHDCP1X_EVENT_READDOWNSTREAM,
+} XHdcp1x_EventType;
+
+/**
+ * This enumerates the Event Types for HDCP Transmitter state machine.
+ */
+typedef enum {
+	XHDCP1X_STATE_DISABLED = XHDCP1X_TX_STATE_DISABLED,
+	XHDCP1X_STATE_DETERMINERXCAPABLE = XHDCP1X_TX_STATE_DETERMINERXCAPABLE,
+	XHDCP1X_STATE_EXCHANGEKSVS = XHDCP1X_TX_STATE_EXCHANGEKSVS,
+	XHDCP1X_STATE_COMPUTATIONS = XHDCP1X_TX_STATE_COMPUTATIONS,
+	XHDCP1X_STATE_VALIDATERX = XHDCP1X_TX_STATE_VALIDATERX,
+	XHDCP1X_STATE_AUTHENTICATED = XHDCP1X_TX_STATE_AUTHENTICATED,
+	XHDCP1X_STATE_LINKINTEGRITYCHECK = XHDCP1X_TX_STATE_LINKINTEGRITYCHECK,
+	XHDCP1X_STATE_TESTFORREPEATER = XHDCP1X_TX_STATE_TESTFORREPEATER,
+	XHDCP1X_STATE_WAITFORREADY = XHDCP1X_TX_STATE_WAITFORREADY,
+	XHDCP1X_STATE_READKSVLIST = XHDCP1X_TX_STATE_READKSVLIST,
+	XHDCP1X_STATE_UNAUTHENTICATED = XHDCP1X_TX_STATE_UNAUTHENTICATED,
+	XHDCP1X_STATE_PHYDOWN = XHDCP1X_TX_STATE_PHYDOWN,
+} XHdcp1x_StateType;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*************************** Function Prototypes *****************************/
+
+static void XHdcp1x_TxDebugLog(const XHdcp1x *InstancePtr, const char *LogMsg);
+static void XHdcp1x_TxPostEvent(XHdcp1x *InstancePtr, XHdcp1x_EventType Event);
+static void XHdcp1x_TxStartTimer(XHdcp1x *InstancePtr, u16 TimeoutInMs);
+static void XHdcp1x_TxStopTimer(XHdcp1x *InstancePtr);
+static void XHdcp1x_TxBusyDelay(XHdcp1x *InstancePtr, u16 DelayInMs);
+static void XHdcp1x_TxReauthenticateCallback(void *Parameter);
+static void XHdcp1x_TxCheckLinkCallback(void *Parameter);
+static void XHdcp1x_TxSetCheckLinkState(XHdcp1x *InstancePtr, int IsEnabled);
+static void XHdcp1x_TxEnableEncryptionState(XHdcp1x *InstancePtr);
+static void XHdcp1x_TxDisableEncryptionState(XHdcp1x *InstancePtr);
+static void XHdcp1x_TxEnableState(XHdcp1x *InstancePtr);
+static void XHdcp1x_TxDisableState(XHdcp1x *InstancePtr);
+static void XHdcp1x_TxCheckRxCapable(const XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static u64 XHdcp1x_TxGenerateAn(XHdcp1x *InstancePtr);
+static int XHdcp1x_TxIsKsvValid(u64 Ksv);
+static void XHdcp1x_TxExchangeKsvs(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxStartComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxPollForComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxValidateRx(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxCheckLinkIntegrity(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxTestForRepeater(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxPollForWaitForReady(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static int XHdcp1x_TxSetRepeaterInfo(XHdcp1x *InstancePtr);
+static int XHdcp1x_TxValidateKsvList(XHdcp1x *InstancePtr, u16 RepeaterInfo);
+static void XHdcp1x_TxReadKsvList(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunDisabledState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunDetermineRxCapableState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunExchangeKsvsState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunComputationsState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunValidateRxState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunAuthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunLinkIntegrityCheckState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunTestForRepeaterState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunWaitForReadyState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunReadKsvListState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunUnauthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxRunPhysicalLayerDownState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxEnterState(XHdcp1x *InstancePtr, XHdcp1x_StateType State,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxExitState(XHdcp1x *InstancePtr, XHdcp1x_StateType State,
+		XHdcp1x_StateType *NextStatePtr);
+static void XHdcp1x_TxDoTheState(XHdcp1x *InstancePtr, XHdcp1x_EventType Event);
+static void XHdcp1x_TxProcessPending(XHdcp1x *InstancePtr);
+static const char *XHdcp1x_TxStateToString(XHdcp1x_StateType State);
+#if XHDCP1X_ADDITIONAL_DEBUG
+static const char *XHdcp1x_TxEventToString(XHdcp1x_EventType Event);
+#endif
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function installs callback functions for the given
+* HandlerType:
+*
+* @param	InstancePtr is a pointer to the HDCP core instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return
+*		- XST_SUCCESS if callback function installed successfully.
+*		- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*			installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp1x_TxSetCallback(XHdcp1x *InstancePtr,
+	XHdcp1x_HandlerType HandlerType, void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType > (XHDCP1X_HANDLER_UNDEFINED));
+	Xil_AssertNonvoid(HandlerType < (XHDCP1X_HANDLER_INVALID));
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	u32 Status = XST_NO_DATA;
+
+	/* Check for handler type */
+	switch (HandlerType)
+	{
+		/* DDC write */
+		case (XHDCP1X_HANDLER_DDC_WRITE):
+			InstancePtr->Tx.DdcWrite
+				= (XHdcp1x_RunDdcHandler)CallbackFunc;
+			InstancePtr->Tx.DdcWriteRef = CallbackRef;
+			InstancePtr->Tx.IsDdcWriteSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		/* DDC read */
+		case (XHDCP1X_HANDLER_DDC_READ):
+			InstancePtr->Tx.DdcRead
+				= (XHdcp1x_RunDdcHandler)CallbackFunc;
+			InstancePtr->Tx.DdcReadRef = CallbackRef;
+			InstancePtr->Tx.IsDdcReadSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		/* Authenticated */
+		case (XHDCP1X_HANDLER_AUTHENTICATED):
+			InstancePtr->Tx.AuthenticatedCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Tx.AuthenticatedCallbackRef = CallbackRef;
+			InstancePtr->Tx.IsAuthenticatedCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		/* Repeater - Repeater exchange (values) */
+		/* Equivalent of case (XHDCP1X_RPTR_HDLR_REPEATER_EXCHANGE): */
+		case (XHDCP1X_HANDLER_RPTR_RPTREXCHANGE):
+			InstancePtr->Tx.RepeaterExchangeCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Tx.RepeaterExchangeRef = CallbackRef;
+			InstancePtr->Tx.IsRepeaterExchangeCallbackSet = (TRUE);
+			break;
+
+		/* Un-authenticated */
+		case (XHDCP1X_HANDLER_UNAUTHENTICATED):
+			InstancePtr->Tx.UnauthenticatedCallback
+				= (XHdcp1x_Callback)CallbackFunc;
+			InstancePtr->Tx.UnauthenticatedCallbackRef
+				= CallbackRef;
+			InstancePtr->Tx.IsUnauthenticatedCallbackSet = (TRUE);
+			break;
+
+		default:
+			Status = (XST_INVALID_PARAM);
+			break;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes a transmit state machine.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_TxInit(XHdcp1x *InstancePtr)
+{
+	XHdcp1x_StateType DummyState = XHDCP1X_STATE_DISABLED;
+
+	/* Update theHandler */
+	InstancePtr->Tx.PendingEvents = 0;
+
+	/* Kick the state machine */
+	XHdcp1x_TxEnterState(InstancePtr, XHDCP1X_STATE_DISABLED, &DummyState);
+}
+
+/*****************************************************************************/
+/**
+* This function polls an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxPoll(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Process any pending events */
+	XHdcp1x_TxProcessPending(InstancePtr);
+
+	/* Poll it */
+	XHdcp1x_TxDoTheState(InstancePtr, XHDCP1X_EVENT_POLL);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function resets an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		This function disables and then re-enables the interface.
+*
+******************************************************************************/
+int XHdcp1x_TxReset(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Reset it */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_DISABLE);
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_ENABLE);
+
+	/* Reset the Authentication In Progress Flag. */
+	InstancePtr->Tx.IsAuthReqPending = (FALSE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function enables an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxEnable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post it */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_ENABLE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxDisable(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post it */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_DISABLE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if it is enabled.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	Truth value indicating is enabled (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsEnabled(const XHdcp1x *InstancePtr)
+{
+	int IsEnabled = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Which state? */
+	switch (InstancePtr->Tx.CurrentState) {
+		case XHDCP1X_STATE_DISABLED:
+			IsEnabled = FALSE;
+			break;
+
+		/* Otherwise */
+		default:
+			IsEnabled = TRUE;
+			break;
+	}
+
+	return (IsEnabled);
+}
+
+/*****************************************************************************/
+/**
+* This function updates the physical state of an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	IsUp is truth value indicating the status of physical interface.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxSetPhysicalState(XHdcp1x *InstancePtr, int IsUp)
+{
+	int Status = XST_SUCCESS;
+	XHdcp1x_EventType Event = XHDCP1X_EVENT_PHYDOWN;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine Event */
+	if (IsUp) {
+		Event = XHDCP1X_EVENT_PHYUP;
+	}
+
+	/* Post it */
+	XHdcp1x_TxPostEvent(InstancePtr, Event);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function set the lane count of an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	LaneCount is the number of lanes of the interface.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxSetLaneCount(XHdcp1x *InstancePtr, int LaneCount)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(LaneCount > 0);
+
+	/* Set it */
+	return (XHdcp1x_CipherSetNumLanes(InstancePtr, LaneCount));
+}
+
+/*****************************************************************************/
+/**
+* This function initiates authentication on an interface.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxAuthenticate(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Set auth request pending flag */
+	InstancePtr->Tx.IsAuthReqPending = (TRUE);
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post the re-authentication request */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_AUTHENTICATE);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function initiates the transmitter to read READY bit from downstream and
+* complete second part of authentication.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxReadDownstream(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Post the re-authentication request */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_READDOWNSTREAM);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if authentication is still in
+* progress.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	Truth value indicating in progress (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsInProgress(const XHdcp1x *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Tx.IsAuthReqPending);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if its been authenticated.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	Truth value indicating authenticated (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsAuthenticated(const XHdcp1x *InstancePtr)
+{
+	int Authenticated = FALSE;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Case-wise process the kind of state called */
+	switch (InstancePtr->Tx.CurrentState) {
+		/* For the authenticated and link integrity check states */
+		case XHDCP1X_STATE_AUTHENTICATED:
+		case XHDCP1X_STATE_LINKINTEGRITYCHECK:
+			Authenticated = TRUE;
+			break;
+
+		/* Otherwise */
+		default:
+			Authenticated = FALSE;
+			break;
+	}
+
+	return (Authenticated);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if its in the computations state.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	Truth value indicating authenticated (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsInComputations(const XHdcp1x *InstancePtr)
+{
+	int IsInComp = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine IsInComputations */
+	if (InstancePtr->Tx.CurrentState == XHDCP1X_STATE_COMPUTATIONS) {
+		IsInComp = TRUE;
+	}
+
+	return (IsInComp);
+}
+
+/*****************************************************************************/
+/**
+* This function queries an interface to check if its in the
+* wait-for-ready state.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	Truth value indicating authenticated (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsInWaitforready(const XHdcp1x *InstancePtr)
+{
+	int IsInWfr = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine IsInWaitforready */
+	if (InstancePtr->Tx.CurrentState == XHDCP1X_STATE_WAITFORREADY) {
+		IsInWfr = TRUE;
+	}
+
+	return (IsInWfr);
+}
+
+/*****************************************************************************/
+/**
+* This function queries the downstream device to check if the downstream
+* device is HDCP capable.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	Truth value indicating HDCP capability (true) or not (false).
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsDownstrmCapable(const XHdcp1x *InstancePtr)
+{
+	int IsCapable = FALSE;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Determine IsCapable */
+	if (XHdcp1x_PortIsCapable(InstancePtr)) {
+		IsCapable = TRUE;
+	}
+
+	return (IsCapable);
+}
+
+/*****************************************************************************/
+/**
+* This function retrieves the current encryption stream map.
+*
+* @param	InstancePtr the transmitter instance.
+*
+* @return	The current encryption stream map.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdcp1x_TxGetEncryption(const XHdcp1x *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Tx.EncryptionMap);
+}
+
+/*****************************************************************************/
+/**
+* This function enables encryption on set of streams on an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	StreamMap is the bit map of streams to enable encryption on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxEnableEncryption(XHdcp1x *InstancePtr, u64 StreamMap)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Update InstancePtr */
+	InstancePtr->Tx.EncryptionMap |= StreamMap;
+
+	/* Check for authenticated */
+	if (XHdcp1x_TxIsAuthenticated(InstancePtr)) {
+		XHdcp1x_TxEnableEncryptionState(InstancePtr);
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function disables encryption on set of streams on an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	StreamMap is the bit map of streams to disable encryption on.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxDisableEncryption(XHdcp1x *InstancePtr, u64 StreamMap)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Only disable encryption when the TX is enabled */
+	if (XHdcp1x_TxIsEnabled(InstancePtr)) {
+
+		/* Disable it */
+		Status = XHdcp1x_CipherDisableEncryption(InstancePtr, StreamMap);
+
+		/* Update InstancePtr */
+		if (Status == XST_SUCCESS) {
+			InstancePtr->Tx.EncryptionMap &= ~StreamMap;
+		}
+	}
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This set a flag that allows the hdcp1x drivers to determine if the
+* transmitter is HDMI or DVI.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_TxSetHdmiMode(XHdcp1x *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Value == FALSE || Value == TRUE);
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+	InstancePtr->Tx.TxIsHdmi = Value;
+#else
+	UNUSED(Value);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function handles a timeout on an HDCP interface.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_TxHandleTimeout(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Post the timeout */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_TIMEOUT);
+}
+
+
+/*****************************************************************************/
+/**
+* This function returns if HDCP TX interface is connected
+* to a downstream repeater.
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		- TRUE if Repeater.
+*		- FALSE if not Repeater,
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxIsRepeater(XHdcp1x *InstancePtr)
+{
+	int Status = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if downstream is Repeater */
+	Status = XHdcp1x_PortIsRepeater(InstancePtr);
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function implements the debug display output for transmit instances.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return
+*		- XST_SUCCESS if successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp1x_TxInfo(const XHdcp1x *InstancePtr)
+{
+	u64 LocalKsv = 0;
+	u32 Version = 0;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Display it */
+	XDEBUG_PRINTF("Type:            ");
+	if (InstancePtr->Config.IsHDMI) {
+		XDEBUG_PRINTF("hdmi-tx\r\n");
+	}
+	else {
+		XDEBUG_PRINTF("dp-tx\r\n");
+	}
+	XDEBUG_PRINTF("Current State:   %s\r\n",
+			XHdcp1x_TxStateToString(InstancePtr->Tx.CurrentState));
+	XDEBUG_PRINTF("Previous State:  %s\r\n",
+			XHdcp1x_TxStateToString(InstancePtr->Tx.PreviousState));
+	XDEBUG_PRINTF("Encrypted?:      %s\r\n",
+			XHdcp1x_IsEncrypted(InstancePtr) ? "Yes" : "No");
+	XDEBUG_PRINTF("State Helper:    %016llX\r\n",
+			InstancePtr->Tx.StateHelper);
+	XDEBUG_PRINTF("Flags:           %04X\r\n",
+			InstancePtr->Tx.Flags);
+	XDEBUG_PRINTF("Encryption Map:  %016llX\r\n",
+			InstancePtr->Tx.EncryptionMap);
+	Version = XHdcp1x_GetDriverVersion();
+	XDEBUG_PRINTF("Driver Version:  %d.%02d.%02d\r\n",
+			((Version >> 16) &0xFFFFu), ((Version >> 8) & 0xFFu),
+			(Version & 0xFFu));
+	Version = XHdcp1x_CipherGetVersion(InstancePtr);
+	XDEBUG_PRINTF("Cipher Version:  %d.%02d.%02d\r\n",
+			((Version >> 16) &0xFFFFu), ((Version >> 8) & 0xFFu),
+			(Version & 0xFFu));
+	LocalKsv = XHdcp1x_CipherGetLocalKsv(InstancePtr);
+	XDEBUG_PRINTF("Local KSV:       %02lX", (LocalKsv >> 32));
+	XDEBUG_PRINTF("%08lX\r\n", (LocalKsv & 0xFFFFFFFFu));
+
+	XDEBUG_PRINTF("\r\n");
+	XDEBUG_PRINTF("Tx Stats\r\n");
+	XDEBUG_PRINTF("Auth Passed:     %d\r\n",
+			InstancePtr->Tx.Stats.AuthPassed);
+	XDEBUG_PRINTF("Auth Failed:     %d\r\n",
+			InstancePtr->Tx.Stats.AuthFailed);
+	XDEBUG_PRINTF("Reauth Requests: %d\r\n",
+			InstancePtr->Tx.Stats.ReauthRequested);
+	XDEBUG_PRINTF("Check Passed:    %d\r\n",
+			InstancePtr->Tx.Stats.LinkCheckPassed);
+	XDEBUG_PRINTF("Check Failed:    %d\r\n",
+			InstancePtr->Tx.Stats.LinkCheckFailed);
+	XDEBUG_PRINTF("Read Failures:   %d\r\n",
+			InstancePtr->Tx.Stats.ReadFailures);
+
+	XDEBUG_PRINTF("\r\n");
+	XDEBUG_PRINTF("Cipher Stats\r\n");
+	XDEBUG_PRINTF("Int Count:       %d\r\n",
+			InstancePtr->Cipher.Stats.IntCount);
+
+	XDEBUG_PRINTF("\r\n");
+	XDEBUG_PRINTF("Port Stats\r\n");
+	XDEBUG_PRINTF("Int Count:       %d\r\n",
+			InstancePtr->Port.Stats.IntCount);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the blank output for the cipher.
+*
+* @param  InstancePtr is a pointer to the Hdcp1.4 core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp1x_TxEnableBlank(XHdcp1x *InstancePtr)
+{
+	XHdcp1x_CipherEnableBlank(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the blank output for the cipher.
+*
+* @param  InstancePtr is a pointer to the Hdcp1.4 core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp1x_TxDisableBlank(XHdcp1x *InstancePtr)
+{
+	XHdcp1x_CipherDisableBlank(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+* This function logs a debug message on behalf of a handler state machine.
+*
+* @param	InstancePtr is the receiver instance.
+* @param	LogMsg is the message to log.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxDebugLog(const XHdcp1x *InstancePtr, const char *LogMsg)
+{
+#if 0
+	char Label[16];
+
+	/* Format Label */
+	snprintf(Label, sizeof(Label), "hdcp-tx(%hu) - ",
+			 InstancePtr->Config.DeviceId);
+
+	/* Log it */
+	XHDCP1X_DEBUG_LOGMSG(Label);
+	XHDCP1X_DEBUG_LOGMSG(LogMsg);
+	XHDCP1X_DEBUG_LOGMSG("\r\n");
+#else
+	//xil_printf("hdcp-tx(%d) - %s\n", InstancePtr->Config.DeviceId, LogMsg);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function posts an event to a state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to post.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxPostEvent(XHdcp1x *InstancePtr, XHdcp1x_EventType Event)
+{
+	/* Check for disable and clear any pending enable */
+	if (Event == XHDCP1X_EVENT_DISABLE) {
+		InstancePtr->Tx.PendingEvents &= ~(1u << XHDCP1X_EVENT_ENABLE);
+	}
+	/* Check for phy-down and clear any pending phy-up */
+	else if (Event == XHDCP1X_EVENT_PHYDOWN) {
+		InstancePtr->Tx.PendingEvents &= ~(1u << XHDCP1X_EVENT_PHYUP);
+	}
+
+	/* Post it */
+	InstancePtr->Tx.PendingEvents |= (1u << Event);
+}
+
+/*****************************************************************************/
+/**
+* This function starts a state machine's timer.
+*
+* @param	InstancePtr is the state machine.
+* @param	TimeoutInMs is the timeout in milli-seconds.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxStartTimer(XHdcp1x *InstancePtr, u16 TimeoutInMs)
+{
+	/* Start it */
+	XHdcp1x_PlatformTimerStart(InstancePtr, TimeoutInMs);
+}
+
+/*****************************************************************************/
+/**
+* This function stops a state machine's timer.
+*
+* @param	InstancePtr is the state machine.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxStopTimer(XHdcp1x *InstancePtr)
+{
+	/* Stop it */
+	XHdcp1x_PlatformTimerStop(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+* This function busy delays a state machine.
+*
+* @param	InstancePtr is the state machine.
+* @param	DelayInMs is the delay time in milli-seconds.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxBusyDelay(XHdcp1x *InstancePtr, u16 DelayInMs)
+{
+	/* Busy wait */
+	XHdcp1x_PlatformTimerBusy(InstancePtr, DelayInMs);
+}
+
+/*****************************************************************************/
+/**
+* This function acts as the reauthentication callback for a state machine.
+*
+* @param	Parameter is the parameter specified during registration.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxReauthenticateCallback(void *Parameter)
+{
+	XHdcp1x *InstancePtr = Parameter;
+
+	/* Update statistics */
+	InstancePtr->Tx.Stats.ReauthRequested++;
+
+	/* Post the re-authentication request */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_AUTHENTICATE);
+}
+
+/*****************************************************************************/
+/**
+* This function acts as the downstream authentication trigger callback for a
+* Repeater state machine, to start the second part of authentication.
+*
+* @param	Parameter is the parameter specified during registration.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp1x_TxTriggerDownstreamAuth(void *Parameter)
+{
+	XHdcp1x *InstancePtr = Parameter;
+
+	/* Post the re-authentication request */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_AUTHENTICATE);
+}
+
+/*****************************************************************************/
+/**
+* This function acts as the check link callback for a state machine.
+*
+* @param	Parameter is the parameter specified during registration.
+*
+* @return	Mpme/
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxCheckLinkCallback(void *Parameter)
+{
+	XHdcp1x *InstancePtr = Parameter;
+
+	/* Post the check request */
+	XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_CHECK);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the check link state of the handler.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	IsEnabled is truth value indicating on/off.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxSetCheckLinkState(XHdcp1x *InstancePtr, int IsEnabled)
+{
+	/* Check for HDMI */
+	if (InstancePtr->Config.IsHDMI) {
+		/* Check for enabled */
+		if (IsEnabled) {
+			/* Register Callback */
+			XHdcp1x_CipherSetCallback(InstancePtr,
+				XHDCP1X_CIPHER_HANDLER_Ri_UPDATE,
+				&XHdcp1x_TxCheckLinkCallback, InstancePtr);
+
+			/* Enable it */
+			XHdcp1x_CipherSetRiUpdate(InstancePtr, TRUE);
+		}
+		/* Otherwise */
+		else {
+			/* Disable it */
+			XHdcp1x_CipherSetRiUpdate(InstancePtr, FALSE);
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function enables encryption for a state machine.
+*
+* @param	InstancePtr is the HDCP state machine.
+*
+* @return	None.
+*
+* @note		This function inserts a 5ms delay for things to settle when
+*		encryption is actually being disabled.
+*
+******************************************************************************/
+static void XHdcp1x_TxEnableEncryptionState(XHdcp1x *InstancePtr)
+{
+	/* Check for encryption enabled */
+	if (InstancePtr->Tx.EncryptionMap != 0) {
+		u64 StreamMap = 0;
+
+		/* Determine StreamMap */
+		StreamMap =
+			XHdcp1x_CipherGetEncryption(InstancePtr);
+
+		/* Check if there is something to do */
+		if (StreamMap != InstancePtr->Tx.EncryptionMap) {
+			/* Wait a bit */
+			XHdcp1x_TxBusyDelay(InstancePtr, XVPHY_TMO_5MS);
+
+			/* Enable it */
+			XHdcp1x_CipherEnableEncryption(InstancePtr,
+					InstancePtr->Tx.EncryptionMap);
+
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function disables encryption for a state machine.
+*
+* @param	InstancePtr is the HDCP state machine.
+*
+* @return	None.
+*
+* @note		This function inserts a 5ms delay for things to settle when
+*		encryption is actually being disabled.
+*
+******************************************************************************/
+static void XHdcp1x_TxDisableEncryptionState(XHdcp1x *InstancePtr)
+{
+	u64 StreamMap = XHdcp1x_CipherGetEncryption(InstancePtr);
+
+	/* Check if encryption actually enabled */
+	if (StreamMap != 0) {
+		/* Update StreamMap for all stream */
+		StreamMap = (u64)(-1);
+
+		/* Disable it all */
+		XHdcp1x_CipherDisableEncryption(InstancePtr, StreamMap);
+
+		/* Wait at least a frame */
+		XHdcp1x_TxBusyDelay(InstancePtr, XVPHY_TMO_5MS);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function enables a state machine.
+*
+* @param	InstancePtr is the HDCP state machine.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxEnableState(XHdcp1x *InstancePtr)
+{
+	/* Clear statistics */
+	memset(&(InstancePtr->Tx.Stats), 0, sizeof(InstancePtr->Tx.Stats));
+
+	/* Enable the crypto engine */
+	XHdcp1x_CipherEnable(InstancePtr);
+
+	/* Register the re-authentication callback */
+	XHdcp1x_PortSetCallback(InstancePtr,
+			XHDCP1X_PORT_HANDLER_AUTHENTICATE,
+			&XHdcp1x_TxReauthenticateCallback, InstancePtr);
+
+	/* Enable the hdcp port */
+	XHdcp1x_PortEnable(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+* This function disables a state machine.
+*
+* @param	InstancePtr is the HDCP state machine.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxDisableState(XHdcp1x *InstancePtr)
+{
+	/* Disable the hdcp port */
+	XHdcp1x_PortDisable(InstancePtr);
+
+	/* Disable the cryto engine */
+	XHdcp1x_CipherDisable(InstancePtr);
+
+	/* Disable the timer */
+	XHdcp1x_TxStopTimer(InstancePtr);
+
+	/* Update InstancePtr */
+	InstancePtr->Tx.Flags &= ~XVPHY_FLAG_IS_REPEATER;
+	InstancePtr->Tx.StateHelper = 0;
+	InstancePtr->Tx.EncryptionMap = 0;
+}
+
+/*****************************************************************************/
+/**
+* This function checks to ensure that the remote end is HDCP capable.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxCheckRxCapable(const XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Check for capable */
+	if (XHdcp1x_PortIsCapable(InstancePtr)) {
+		/* Log */
+		XHdcp1x_TxDebugLog(InstancePtr, "rx hdcp capable");
+
+		/* Update NextStatePtr */
+		*NextStatePtr = XHDCP1X_STATE_EXCHANGEKSVS;
+	}
+	else {
+		/* Log */
+		XHdcp1x_TxDebugLog(InstancePtr, "rx not capable");
+
+		/* Update NextStatePtr */
+		*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function generates the An from a random number generator.
+*
+* @param	InstancePtr is the HDCP state machine.
+*
+* @return	A 64-bit pseudo random number (An).
+*
+* @note		None.
+*
+******************************************************************************/
+static u64 XHdcp1x_TxGenerateAn(XHdcp1x *InstancePtr)
+{
+	u64 An = 0;
+
+	/* Attempt to generate An */
+	if (XHdcp1x_CipherDoRequest(InstancePtr,
+		XHDCP1X_CIPHER_REQUEST_RNG) == XST_SUCCESS) {
+		/* Wait until done */
+		while (!XHdcp1x_CipherIsRequestComplete(InstancePtr));
+
+		/* Update theAn */
+		An = XHdcp1x_CipherGetMi(InstancePtr);
+	}
+
+	/* Check if zero */
+	if (An == 0) {
+		An = 0x351F7175406A74Dull;
+	}
+
+	return (An);
+}
+
+/*****************************************************************************/
+/**
+* This function validates a KSV value as having 20 1s and 20 0s.
+*
+* @param	Ksv is the value to validate.
+*
+* @return	Truth value indicating valid (TRUE) or not (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_TxIsKsvValid(u64 Ksv)
+{
+	int IsValid = FALSE;
+	int NumOnes = 0;
+
+	/* Determine NumOnes */
+	while (Ksv != 0) {
+		if ((Ksv & 1) != 0) {
+			NumOnes++;
+		}
+		Ksv >>= 1;
+	}
+
+	/* Check for 20 1s */
+	if (NumOnes == 20) {
+		IsValid = TRUE;
+	}
+
+	return (IsValid);
+}
+
+/*****************************************************************************/
+/**
+* This function exchanges the ksvs between the two ends of the link.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxExchangeKsvs(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	u8 Buf[8];
+
+	/* Initialize Buf */
+	memset(Buf, 0, 8);
+
+	/* Update NextStatePtr - assume failure */
+	*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+
+	/* Read the Bksv from remote end */
+	if (XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BKSV,
+			Buf, 5) > 0) {
+		u64 RemoteKsv = 0;
+
+		/* Determine theRemoteKsv */
+		XHDCP1X_PORT_BUF_TO_UINT(RemoteKsv, Buf,
+				XHDCP1X_PORT_SIZE_BKSV * 8);
+
+		/* Check for invalid */
+		if (!XHdcp1x_TxIsKsvValid(RemoteKsv)) {
+			XHdcp1x_TxDebugLog(InstancePtr, "Bksv invalid");
+		}
+		/* Check for revoked */
+		else if (XHdcp1x_PlatformIsKsvRevoked(InstancePtr,
+				RemoteKsv)) {
+			XHdcp1x_TxDebugLog(InstancePtr, "Bksv is revoked");
+		}
+		/* Otherwise we're good to go */
+		else {
+			u64 LocalKsv = 0;
+			u64 An = 0;
+			u8 Buf_AInfo[XHDCP1X_PORT_SIZE_AINFO];
+
+			/* Check for repeater and update InstancePtr */
+			if (XHdcp1x_PortIsRepeater(InstancePtr)) {
+				InstancePtr->Tx.Flags |= XVPHY_FLAG_IS_REPEATER;
+			}
+			else {
+				InstancePtr->Tx.Flags &=
+						~XVPHY_FLAG_IS_REPEATER;
+			}
+
+			/* Generate theAn */
+			An = XHdcp1x_TxGenerateAn(InstancePtr);
+
+			/* Save theAn into the state helper for use later */
+			InstancePtr->Tx.StateHelper = An;
+
+			/* Determine theLocalKsv */
+			LocalKsv = XHdcp1x_CipherGetLocalKsv(InstancePtr);
+
+			/* Load the cipher with the remote ksv */
+			XHdcp1x_CipherSetRemoteKsv(InstancePtr, RemoteKsv);
+
+			/* Clear AINFO */
+			memset(Buf_AInfo, 0, XHDCP1X_PORT_SIZE_AINFO);
+			XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_AINFO,
+					Buf_AInfo, XHDCP1X_PORT_SIZE_AINFO);
+
+			/* Send An to remote */
+			XHDCP1X_PORT_UINT_TO_BUF(Buf, An,
+					XHDCP1X_PORT_SIZE_AN * 8);
+			XHdcp1x_PortWrite(InstancePtr, XHDCP1X_PORT_OFFSET_AN,
+					Buf, XHDCP1X_PORT_SIZE_AN);
+
+			/* Send AKsv to remote */
+			XHDCP1X_PORT_UINT_TO_BUF(Buf, LocalKsv,
+					XHDCP1X_PORT_SIZE_AKSV * 8);
+			XHdcp1x_PortWrite(InstancePtr,
+					XHDCP1X_PORT_OFFSET_AKSV,
+					Buf, XHDCP1X_PORT_SIZE_AKSV);
+
+			/* Update NextStatePtr */
+			*NextStatePtr = XHDCP1X_STATE_COMPUTATIONS;
+		}
+	}
+	/* Otherwise */
+	else {
+		/* Update the statistics */
+		InstancePtr->Tx.Stats.ReadFailures++;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function initiates the computations for a state machine.
+*
+* @param	InstancePtr is the HDCP receiver state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxStartComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	u64 Value = 0;
+	u32 X = 0;
+	u32 Y = 0;
+	u32 Z = 0;
+
+	/* Log */
+	XHdcp1x_TxDebugLog(InstancePtr, "starting computations");
+
+	/* Update Value with An */
+	Value = InstancePtr->Tx.StateHelper;
+
+	/* Load the cipher B registers with An */
+	X = (u32)(Value & 0x0FFFFFFFul);
+	Value >>= 28;
+	Y = (u32)(Value & 0x0FFFFFFFul);
+	Value >>= 28;
+	Z = (u32)(Value & 0x000000FFul);
+	if ((InstancePtr->Tx.Flags & XVPHY_FLAG_IS_REPEATER) != 0) {
+		Z |= (1ul << 8);
+	}
+	XHdcp1x_CipherSetB(InstancePtr, X, Y, Z);
+
+	/* Initiate the block cipher */
+	XHdcp1x_CipherDoRequest(InstancePtr, XHDCP1X_CIPHER_REQUEST_BLOCK);
+
+	/* Update NextStatePtr */
+	*NextStatePtr = XHDCP1X_STATE_COMPUTATIONS;
+}
+
+/*****************************************************************************/
+/**
+* This function polls the progress of the computations for a state machine.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxPollForComputations(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Check for done */
+	if (XHdcp1x_CipherIsRequestComplete(InstancePtr)) {
+		XHdcp1x_TxDebugLog(InstancePtr, "computations complete");
+		*NextStatePtr = XHDCP1X_STATE_VALIDATERX;
+	}
+	else {
+		XHdcp1x_TxDebugLog(InstancePtr, "waiting for computations");
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function validates the attached receiver.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxValidateRx(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	u8 Buf[2];
+	int NumTries = 3;
+
+	/* Update NextStatePtr */
+	*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+
+	/* Attempt to read Ro */
+	do {
+		/* Read the remote Ro' */
+		if (XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_RO,
+				Buf, 2) > 0) {
+			char LogBuf[32];
+			u16 RemoteRo = 0;
+			u16 LocalRo = 0;
+
+			/* Determine RemoteRo */
+			XHDCP1X_PORT_BUF_TO_UINT(RemoteRo, Buf, (2 * 8));
+
+			/* Determine theLLocalRoocalRo */
+			LocalRo = XHdcp1x_CipherGetRo(InstancePtr);
+
+			/* Compare the Ro values */
+			if (LocalRo == RemoteRo) {
+
+				/* Determine theLogBuf */
+				snprintf(LogBuf, 32, "rx valid Ro/Ro' (%04X)",
+						LocalRo);
+
+				/* Update NextStatePtr */
+				*NextStatePtr = XHDCP1X_STATE_TESTFORREPEATER;
+			}
+			/* Otherwise */
+			else {
+				/* Determine theLogBuf */
+				snprintf(LogBuf, 32, "Ro/Ro' mismatch (%04X/"
+						"%04X)", LocalRo, RemoteRo);
+
+				/* Update statistics if the last attempt */
+				if (NumTries == 1)
+					InstancePtr->Tx.Stats.AuthFailed++;
+			}
+
+			/* Log */
+			XHdcp1x_TxDebugLog(InstancePtr, LogBuf);
+		}
+		/* Otherwise */
+		else {
+			/* Log */
+			XHdcp1x_TxDebugLog(InstancePtr, "Ro' read failure");
+
+			/* Update the statistics */
+			InstancePtr->Tx.Stats.ReadFailures++;
+		}
+
+		/* Update for loop */
+		NumTries--;
+	}
+	while ((*NextStatePtr == XHDCP1X_STATE_UNAUTHENTICATED) &&
+		(NumTries > 0));
+}
+
+/*****************************************************************************/
+/**
+* This function checks the integrity of a HDCP link.
+*
+* @param	InstancePtr is the hdcp state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxCheckLinkIntegrity(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	u8 Buf[2];
+	int NumTries = 3;
+
+	/* Update theNextState */
+	*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+
+	/* Iterate through the tries */
+	do {
+		/* Read the remote Ri' */
+		if (XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_RO,
+				Buf, 2) > 0) {
+
+			char LogBuf[48];
+			u16 RemoteRi = 0;
+			u16 LocalRi = 0;
+
+			/* Determine theRemoteRo */
+			XHDCP1X_PORT_BUF_TO_UINT(RemoteRi, Buf, 16);
+
+			/* Determine theLocalRi */
+			LocalRi = XHdcp1x_CipherGetRi(InstancePtr);
+
+			/* Compare the local and remote values */
+			if (LocalRi == RemoteRi) {
+				*NextStatePtr = XHDCP1X_STATE_AUTHENTICATED;
+				snprintf(LogBuf, 48, "link check passed Ri/Ri'"
+						"(%04X)", LocalRi);
+			}
+			/* Check for last attempt */
+			else if (NumTries == 1) {
+				snprintf(LogBuf, 48, "link check failed Ri/Ri'"
+						"(%04X/%04X)", LocalRi,
+						RemoteRi);
+			}
+
+			/* Log */
+			XHdcp1x_TxDebugLog(InstancePtr, LogBuf);
+		}
+		else {
+			XHdcp1x_TxDebugLog(InstancePtr, "Ri' read failure");
+			InstancePtr->Tx.Stats.ReadFailures++;
+		}
+
+		/* Update for loop */
+		NumTries--;
+	} while ((*NextStatePtr != XHDCP1X_STATE_AUTHENTICATED) &&
+		(NumTries > 0));
+
+	/* Check for success */
+	if (*NextStatePtr == XHDCP1X_STATE_AUTHENTICATED) {
+		InstancePtr->Tx.Stats.LinkCheckPassed++;
+	}
+	else {
+		InstancePtr->Tx.Stats.LinkCheckFailed++;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function checks the remote end to see if its a repeater.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		The implementation of this function enables encryption when a
+*		repeater is detected downstream. The standard is ambiguous
+*		as to the handling of this specific case by this behaviour is
+*		required in order to pass the Unigraf compliance test suite.
+*
+******************************************************************************/
+static void XHdcp1x_TxTestForRepeater(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Check for repeater */
+	if (XHdcp1x_PortIsRepeater(InstancePtr)) {
+
+		/* Update InstancePtr */
+		InstancePtr->Tx.Flags |= XVPHY_FLAG_IS_REPEATER;
+
+		/* Update NextStatePtr */
+		*NextStatePtr = XHDCP1X_STATE_WAITFORREADY;
+
+		/* Log */
+		XHdcp1x_TxDebugLog(InstancePtr, "repeater detected");
+
+	}
+	else {
+		/* Update InstancePtr */
+		InstancePtr->Tx.Flags &= ~XVPHY_FLAG_IS_REPEATER;
+
+		/* Set the Down Stream Ready flag - in case of repeater
+		 * we are ready to send repeater values upstream */
+		InstancePtr->Tx.DownstreamReady = 1;
+
+		/* Update NextStatePtr */
+		*NextStatePtr = XHDCP1X_STATE_AUTHENTICATED;
+
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function polls a state machine in the "wait for ready" state.
+*
+* @param	InstancePtr is the hdcp state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxPollForWaitForReady(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	u16 RepeaterInfo = 0;
+	int Status = XST_SUCCESS;
+
+	/* Attempt to read the repeater info */
+	Status = XHdcp1x_PortGetRepeaterInfo(InstancePtr, &RepeaterInfo);
+	if (Status == XST_SUCCESS) {
+		/* Check that neither cascade or device numbers exceeded */
+		if ((!XHdcp1x_TxGetTopologyMaxCascadeExceeded(InstancePtr)) &&
+		    (!XHdcp1x_TxGetTopologyMaxDevsExceeded(InstancePtr))) {
+
+			/* Check for at least one attached device */
+			if ((RepeaterInfo & 0x007Fu) != 0) {
+				/* Update InstancePtr */
+				InstancePtr->Tx.StateHelper = RepeaterInfo;
+
+				/* Update NextStatePtr */
+				*NextStatePtr = XHDCP1X_STATE_READKSVLIST;
+
+				/* No topology errors. */
+				InstancePtr->RepeaterValues.hdcp14_PropagateTopoErrUpstream = FALSE;
+
+				/* Log */
+				XHdcp1x_TxDebugLog(InstancePtr,
+					"devices attached: ksv list ready");
+			}
+			/* Otherwise */
+			else {
+				/*
+				 * Check if Repeater. If repeater, goto
+				 * unauthenticated state and wait for the
+				 * Repeater RX interface to trigger
+				 * authentication after timing out of
+				 * WaitForDownstream state.
+				 * Otherwise, restart authentication on the TX.
+				 */
+				if (InstancePtr->IsRepeater) {
+				/* Update NextStatePtr */
+				*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+				} else {
+				/* Update NextStatePtr */
+				*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+				}
+
+				/* Log */
+				XHdcp1x_TxDebugLog(InstancePtr,
+					"no attached devices");
+			}
+		}
+		/* Check for cascade exceeded */
+		else {
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			/* Disable the hdcp encryption for both HDMI and DP.
+			 * But currently only doing it for HDMI. */
+			XHdcp1x_TxDisableEncryptionState(InstancePtr);
+
+			/* Propagate the failure upstream */
+			InstancePtr->RepeaterValues.Depth =
+					((RepeaterInfo & 0x0700u) >>
+					 XHDCP1X_PORT_BSTATUS_DEPTH_SHIFT);
+			InstancePtr->RepeaterValues.DeviceCount =
+					(RepeaterInfo &
+					 XHDCP1X_PORT_BSTATUS_DEV_CNT_MASK);
+			/* Set the KSV List to include the downstream
+			 * device's BKSV. Do not Validate or assemble the KSV
+			 * List from downstream.*/
+			u8 Bksv[8];
+
+			XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BKSV,
+					Bksv, 5);
+
+			u64 RemoteKsv = 0;
+
+			/* Determine theRemoteKsv */
+			XHDCP1X_PORT_BUF_TO_UINT(RemoteKsv, Bksv,
+					XHDCP1X_PORT_SIZE_BKSV * 8);
+
+			/* Check for invalid */
+			if (!XHdcp1x_TxIsKsvValid(RemoteKsv)) {
+				InstancePtr->RepeaterValues.KsvList[0] =
+					RemoteKsv;
+			} else {
+				InstancePtr->RepeaterValues.KsvList[0] = 0x0;
+			}
+
+			/* Set V' to 0x0. */
+			memset(InstancePtr->RepeaterValues.V, 0x0,
+			       sizeof(u32)*5);
+
+			InstancePtr->RepeaterValues.hdcp14_PropagateTopoErrUpstream = TRUE;
+
+			if (InstancePtr->Tx.IsRepeaterExchangeCallbackSet) {
+				InstancePtr->Tx.RepeaterExchangeCallback(
+					InstancePtr->Tx.RepeaterExchangeRef);
+			}
+#endif
+
+			/* Update NextStatePtr */
+			*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+
+			/* Log */
+			if ((RepeaterInfo & 0x0800u) != 0) {
+				XHdcp1x_TxDebugLog(InstancePtr,
+					"max cascade exceeded");
+			}
+			else {
+				XHdcp1x_TxDebugLog(InstancePtr,
+					"max devices exceeded");
+			}
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function validates the ksv list from an attached repeater.
+*
+* @param	InstancePtr is the hdcp state machine.
+* @param	RepeaterInfo is the repeater information.
+*
+* @return	Truth value indicating valid (TRUE) or invalid (FALSE).
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_TxValidateKsvList(XHdcp1x *InstancePtr, u16 RepeaterInfo)
+{
+	SHA1Context Sha1Context;
+	u8 Buf[24];
+	int NumToRead = 0;
+	int KsvCount = 0;
+	int IsValid = FALSE;
+
+	u8 ksvListHolder[127*XHDCP1X_PORT_SIZE_BKSV];
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+
+#else
+
+	int NumOfKsvsToRead = 0;
+	unsigned int KSVListSize = 0;
+	unsigned int ksvListByteCount = 0;
+
+#endif
+
+	/* Initialize the local KSV fifo */
+	memset(ksvListHolder, 0, (127*XHDCP1X_PORT_SIZE_BKSV));
+
+	/* Initialize Buf */
+	memset(Buf, 0, 24);
+
+	/* Initialize Sha1Context */
+	SHA1Reset(&Sha1Context);
+
+	/* Assume success */
+	IsValid = TRUE;
+
+	/* Determine theNumToRead */
+	NumToRead = (((RepeaterInfo & 0x7Fu) * 5));
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+	/* Read the ksv list */
+	/* Read the entire KSV fifo list in one go */
+	int ByteCount = 0;
+
+	if(XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_KSVFIFO,
+			ksvListHolder, NumToRead) ) {
+
+		/* Update the calculation of V */
+		SHA1Input(&Sha1Context, ksvListHolder, NumToRead);
+
+		/* Update this value in the RepeaterExchange
+		 * structure to be read later by RX */
+
+		u64 Value = 0;
+		u32 Index;
+		while (ByteCount < NumToRead) {
+			if((ByteCount + 1) % 5 == 0) {
+
+				Index = (((ByteCount+1) / XHDCP1X_PORT_SIZE_BKSV) - 1) * XHDCP1X_PORT_SIZE_BKSV;
+
+				XHDCP1X_PORT_BUF_TO_UINT(Value ,
+						(ksvListHolder + ( (((ByteCount+1)
+						/ XHDCP1X_PORT_SIZE_BKSV) - 1)
+						* XHDCP1X_PORT_SIZE_BKSV)),
+					XHDCP1X_PORT_SIZE_BKSV * 8);
+				if (!(Value)) {
+					XHdcp1x_TxDebugLog(InstancePtr ,
+						"Error: Null KSV read "
+						"from downstream KSV List");
+				}
+				InstancePtr->RepeaterValues.KsvList[KsvCount++] =
+					(Value & 0xFFFFFFFFFFul);
+				Value = 0;
+			}
+
+			ByteCount++;
+
+		}
+
+		UNUSED(Index);
+	}
+	else {
+		/* Update the statistics */
+		InstancePtr->Tx.Stats.ReadFailures++;
+
+		/* Update IsValid */
+		IsValid = FALSE;
+	}
+
+#else
+
+	NumOfKsvsToRead = (NumToRead / 5);
+
+	KSVListSize = NumOfKsvsToRead;
+
+	/* Read the ksv list */
+	do {
+		/* Read 15 bytes at a go */
+		int NumThisTime = XHDCP1X_PORT_SIZE_KSVFIFO;
+		int NumOfKsvsThisTime = 3;
+
+		/* Truncate if necessary */
+		if (NumThisTime > NumToRead) {
+			NumThisTime = NumToRead;
+		}
+
+		if (NumOfKsvsThisTime > NumOfKsvsToRead) {
+			NumOfKsvsThisTime = NumOfKsvsToRead;
+		}
+
+		/* Read the next chunk of the list */
+		if (XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_KSVFIFO,
+				Buf, NumThisTime) > 0) {
+
+			/* Update the calculation of V */
+			SHA1Input(&Sha1Context, Buf, NumThisTime);
+
+			/* Duplicate the buffer */
+			int BufReadKsvCount=0;
+			while(BufReadKsvCount < NumThisTime) {
+				ksvListHolder[ksvListByteCount++] = Buf[BufReadKsvCount];
+				BufReadKsvCount++;
+			}
+
+		}
+		else {
+			/* Update the statistics */
+			InstancePtr->Tx.Stats.ReadFailures++;
+
+			/* Update IsValid */
+			IsValid = FALSE;
+		}
+
+		/* Update for loop */
+		NumToRead -= NumThisTime;
+		NumOfKsvsToRead -= NumOfKsvsThisTime;
+
+	} while ((NumToRead > 0) && (IsValid));
+
+#endif
+
+	/* Check for success */
+	if (IsValid) {
+		u64 Mo = 0;
+		u8 Sha1Result[SHA1HashSize];
+
+		/* Insert RepeaterInfo into the SHA-1 transform */
+		Buf[0] = (u8) (RepeaterInfo & 0xFFu);
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+		Buf[1] = (u8) ( ((RepeaterInfo |
+			(XHDCP1X_PORT_BIT_BSTATUS_HDMI_MODE))
+			>> XHDCP1X_PORT_BSTATUS_DEPTH_SHIFT) & 0xFFu);
+#else
+		Buf[1] = (u8) ((RepeaterInfo >> XHDCP1X_PORT_BINFO_DEPTH_SHIFT)
+						& 0xFFu);
+#endif
+		SHA1Input(&Sha1Context, Buf, 2);
+
+		/* Insert the Mo into the SHA-1 transform */
+		Mo = XHdcp1x_CipherGetMo(InstancePtr);
+		XHDCP1X_PORT_UINT_TO_BUF(Buf, Mo, 64);
+		SHA1Input(&Sha1Context, Buf, 8);
+
+		/* Finalize the SHA-1 result and confirm success */
+		if (SHA1Result(&Sha1Context, Sha1Result) == shaSuccess) {
+
+			u8 Offset = XHDCP1X_PORT_OFFSET_VH0;
+			const u8 *Sha1Buf = Sha1Result;
+			int NumIterations = (SHA1HashSize >> 2);
+
+			/* Iterate through the SHA-1 chunks */
+			do {
+				u32 CalcValue = 0;
+				u32 ReadValue = 0;
+
+				/* Determine CalcValue */
+				CalcValue = *Sha1Buf++;
+				CalcValue <<= 8;
+				CalcValue |= *Sha1Buf++;
+				CalcValue <<= 8;
+				CalcValue |= *Sha1Buf++;
+				CalcValue <<= 8;
+				CalcValue |= *Sha1Buf++;
+
+				/* Read the value from the far end */
+				if (XHdcp1x_PortRead(InstancePtr, Offset,
+						Buf, 4) > 0) {
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+					/* Storing the V' prime values later */
+#else
+					memcpy(&InstancePtr->RepeaterValues.V[Offset -
+								XHDCP1X_PORT_OFFSET_VH0], Buf, 4);
+#endif
+
+					/* Determine ReadValue */
+					XHDCP1X_PORT_BUF_TO_UINT(ReadValue,
+							Buf, 32);
+				}
+				else {
+					/* Update ReadValue */
+					ReadValue = 0;
+
+					/* Update the statistics */
+					InstancePtr->Tx.Stats.ReadFailures++;
+				}
+
+				/* Check for mismatch */
+				if (CalcValue != ReadValue) {
+					IsValid = FALSE;
+				}
+
+				/* Update for loop */
+				Offset += 4;
+				NumIterations--;
+			}
+			while (NumIterations > 0);
+		}
+		/* Otherwise */
+		else {
+			IsValid = FALSE;
+		}
+	}
+
+	if (InstancePtr->IsRepeater) {
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			/* Do nothing */
+#else
+		/* Update this value in the RepeaterExchange
+		 * structure to be read later by RX
+		 */
+		u64 Value = 0;
+		u32 thisKsv = 0;
+		while(thisKsv < KSVListSize) {
+
+			XHDCP1X_PORT_BUF_TO_UINT(Value ,
+				(ksvListHolder +
+				(thisKsv * XHDCP1X_PORT_SIZE_BKSV)) ,
+				XHDCP1X_PORT_SIZE_BKSV * 8);
+			if (!(Value)) {
+				XHdcp1x_TxDebugLog(InstancePtr ,
+					"Error: Null KSV read "
+					"from downstream KSV List");
+				thisKsv++;
+				continue;
+			}
+
+
+			InstancePtr->RepeaterValues.KsvList[KsvCount++] =
+				(Value & 0xFFFFFFFFFFul);
+
+			Value = 0;
+			thisKsv++;
+		}
+#endif
+
+		{
+			u8 Bksv[5];
+
+			/* Clear Bksv read buffer */
+			memset(Bksv, 0 , 5);
+
+			/* Add the BKSV of the attached downstream repeater to
+			 * the KSV List */
+			XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BKSV,
+					Bksv, 5);
+
+			u64 RemoteKsv = 0;
+
+			/* Determine theRemoteKsv */
+			XHDCP1X_PORT_BUF_TO_UINT(RemoteKsv, Bksv,
+					XHDCP1X_PORT_SIZE_BKSV * 8);
+
+			/* Check for invalid */
+			if (!XHdcp1x_TxIsKsvValid(RemoteKsv)) {
+				XHdcp1x_TxDebugLog(InstancePtr, "Bksv invalid");
+				return FALSE;
+			}
+
+			InstancePtr->RepeaterValues.KsvList[KsvCount] = RemoteKsv;
+		}
+	}
+
+	return (IsValid);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the value of KSV List read in the downstream interface
+* of the repeater topology.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - TRUE if MAX_DEPTH_EXCEEDED
+*           - FALSE if not
+*
+* @note     None.
+*
+******************************************************************************/
+u8 *XHdcp1x_TxGetTopologyKSVList(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	static u8  DeviceList[256][5];
+	u32 DeviceCnt;
+	u32 i;
+
+	memset(DeviceList[0],0,(32*5));
+	DeviceCnt = InstancePtr->RepeaterValues.DeviceCount;
+
+	for(i=0;i<DeviceCnt;i++) {
+		memcpy(&DeviceList[i][0],
+			&InstancePtr->RepeaterValues.KsvList[i], 5);
+	}
+
+	return(DeviceList[0]);
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the value of Depth read in the downstream interface
+* of the repeater topology.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return	Value of Depth.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdcp1x_TxGetTopologyDepth(XHdcp1x *InstancePtr)
+{
+	return (InstancePtr->RepeaterValues.Depth);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the value of Device Count read in the downstream
+* interface of the repeater topology.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - TRUE if MAX_DEPTH_EXCEEDED
+*           - FALSE if not
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdcp1x_TxGetTopologyDeviceCnt(XHdcp1x *InstancePtr)
+{
+	return (InstancePtr->RepeaterValues.DeviceCount);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the MAX_DEPTH_EXCEEDED flag in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - TRUE if MAX_DEPTH_EXCEEDED
+*           - FALSE if not
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdcp1x_TxGetTopologyMaxCascadeExceeded(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 Buf;
+	u32 Status;
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+	/* Read the BStatus Register */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+			&Buf, XHDCP1X_PORT_SIZE_BSTATUS);
+
+	/* BInfo : Max_device_exceeded[7] */
+	Status = (Buf & XHDCP1X_PORT_BSTATUS_BIT_DEPTH_ERR)? TRUE : FALSE;
+#else
+	/* Read the BInfo Register */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&Buf, XHDCP1X_PORT_SIZE_BINFO);
+
+	/* BInfo : Max_device_exceeded[7] */
+	Status = (Buf & XHDCP1X_PORT_BINFO_BIT_DEPTH_ERR)? TRUE : FALSE;
+#endif
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the value of BKSV of the device connected to the
+* repeater downstream interface.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - TRUE if MAX_DEPTH_EXCEEDED
+*           - FALSE if not
+*
+* @note     None.
+*
+******************************************************************************/
+u8 *XHdcp1x_TxGetTopologyBKSV(XHdcp1x *InstancePtr)
+{
+	u8 Buf[8];
+	u64 RemoteKsv = 0;
+	static u8 Bksv[5];
+
+	/* Initialize Buf */
+	memset(Buf, 0, 8);
+	memset(Bksv, 0, 5);
+
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BKSV,
+				Buf, XHDCP1X_PORT_SIZE_BKSV);
+
+	XHDCP1X_PORT_BUF_TO_UINT(RemoteKsv, Buf,
+					XHDCP1X_PORT_SIZE_BKSV * 8);
+
+	memcpy(&Bksv[0], &RemoteKsv, XHDCP1X_PORT_SIZE_BKSV);
+
+	return(&Bksv[0]);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the MAX_DEVICS_EXCEEDED flag in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return
+*           - TRUE if MAX_DEVICES_EXCEEDED
+*           - FALSE if not
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdcp1x_TxGetTopologyMaxDevsExceeded(XHdcp1x *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 Buf;
+	u32 Status;
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+	/* Read the BStatus Register */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+			&Buf, XHDCP1X_PORT_SIZE_BSTATUS);
+
+	/* BInfo : Max_device_exceeded[7] */
+	Status = (Buf & XHDCP1X_PORT_BSTATUS_BIT_DEV_CNT_ERR)? TRUE : FALSE;
+#else
+	/* Read the BInfo Register */
+	XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+			&Buf, XHDCP1X_PORT_SIZE_BINFO);
+
+	/* BInfo : Max_device_exceeded[7] */
+	Status = (Buf & XHDCP1X_PORT_BINFO_BIT_DEV_CNT_ERR)? TRUE : FALSE;
+#endif
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pointer to the downstream Topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp14 core instance.
+*
+* @return   A pointer to the XHdcp14 Topology structure or NULL when
+*           the topology info is invalid.
+*
+* @note     None.
+*
+******************************************************************************/
+XHdcp1x_RepeaterExchange *XHdcp1x_TxGetTopology(XHdcp1x *InstancePtr)
+{
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	if (InstancePtr->IsRepeater) {
+		if (InstancePtr->Tx.CurrentState == XHDCP1X_STATE_AUTHENTICATED) {
+			return &InstancePtr->RepeaterValues;
+		} else if (InstancePtr->RepeaterValues.hdcp14_PropagateTopoErrUpstream == TRUE) {
+			return &InstancePtr->RepeaterValues;
+		}
+	}
+
+	return NULL;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the V'H0, V'H1, V'H2, V'H3, V'H4, KSVList and BInfo values
+* in the HDCP TX HDCP Instance for Repeater validation .
+*
+* @param	InstancePtr is the transmitter instance.
+*
+* @return
+*		-XST_SUCCESS if successful.
+* 		-XST_FAILURE if unsuccessful.
+*
+* @note		None.
+*
+******************************************************************************/
+static int XHdcp1x_TxSetRepeaterInfo(XHdcp1x *InstancePtr)
+{
+	u8 Bksv[8];
+	u32 KsvCount = 0;
+
+	/* Check for repeater */
+	if (XHdcp1x_PortIsRepeater(InstancePtr)) {
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+		u32 Buf;
+#else
+		u16 RepeaterInfo;
+#endif
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+
+		/* Set the SHA1 Hash value */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_VH0,
+				&Buf, XHDCP1X_PORT_SIZE_VH0);
+
+		/* V'H0 */
+		InstancePtr->RepeaterValues.V[0] = (Buf&0xFFFF);
+
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_VH1,
+				&Buf, XHDCP1X_PORT_SIZE_VH1);
+
+		/* V'H1 */
+		InstancePtr->RepeaterValues.V[1] = (Buf&0xFFFF);
+
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_VH2,
+				&Buf, XHDCP1X_PORT_SIZE_VH2);
+
+		/* V'H2 */
+		InstancePtr->RepeaterValues.V[2] = (Buf&0xFFFF);
+
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_VH3,
+				&Buf, XHDCP1X_PORT_SIZE_VH3);
+
+		/* V'H3 */
+		InstancePtr->RepeaterValues.V[3] = (Buf&0xFFFF);
+
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_VH4,
+				&Buf, XHDCP1X_PORT_SIZE_VH4);
+
+		/* V'H4 */
+		InstancePtr->RepeaterValues.V[4] = (Buf&0xFFFF);
+
+#else
+		/* Do nothing for DP */
+#endif
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+
+		/* Copy the Depth read from the downstream HDCP device */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BSTATUS,
+				&Buf, XHDCP1X_PORT_SIZE_BSTATUS);
+		/* BInfo : Device_Count[6:0], Max_device_exceeded[7],
+		 * Depth[10:8], Max_cascade_exceeded[11], Hdmi_Mode[12],
+		 * Hdmi_Reserved_2[13], Rsvd[15:14].
+		 */
+		InstancePtr->RepeaterValues.Depth = ((Buf & 0x0700)>>8);
+
+		/* Copy the device count read from
+		 * the downstream HDCP device */
+		InstancePtr->RepeaterValues.DeviceCount = (Buf & 0x007F);
+		/* Increment the device count by 1 to account for
+		 * the HDCP Repeater system itsef */
+		InstancePtr->RepeaterValues.DeviceCount++;
+#else
+		/* Get the Depth read from the downstream HDCP device */
+		RepeaterInfo = (u16)(InstancePtr->Tx.StateHelper & 0x0FFFu);
+
+		/* BInfo : Device_Count[6:0], Max_device_exceeded[7],
+		 * Depth[10:8], Max_cascade_exceeded[11]
+		 */
+		InstancePtr->RepeaterValues.Depth = ((RepeaterInfo & 0x0700)>>8);
+
+		/* Copy the device count read from
+		 * the downstream HDCP device */
+		InstancePtr->RepeaterValues.DeviceCount = (RepeaterInfo & 0x007F);
+
+		/* Increment the device count by 1 to account for
+		 * the HDCP Repeater system itsef */
+		InstancePtr->RepeaterValues.DeviceCount++;
+#endif
+
+	}/* end of (if (downstream is a Repeater)) */
+	else {
+		/* The downstream is not Repeater and we need to
+		* add the downstream BKSV to the KSV FIFO
+		*/
+
+		/* Write the Depth to the RepeaterValues */
+		InstancePtr->RepeaterValues.Depth = 0;
+
+		/* Write the Device Count to the RepeaterValues */
+		InstancePtr->RepeaterValues.DeviceCount = 1;
+
+		/* Add the BKSV of the attached downstream receiver
+		* to the KSV List */
+		XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BKSV,
+				Bksv, 5);
+
+		u64 RemoteKsv = 0;
+
+		/* Determine theRemoteKsv */
+		XHDCP1X_PORT_BUF_TO_UINT(RemoteKsv, Bksv,
+				XHDCP1X_PORT_SIZE_BKSV * 8);
+
+		/* Check for invalid */
+		if (!XHdcp1x_TxIsKsvValid(RemoteKsv)) {
+			XHdcp1x_TxDebugLog(InstancePtr, "Bksv invalid");
+			return XST_FAILURE;
+		}
+
+		InstancePtr->RepeaterValues.KsvList[KsvCount++] = RemoteKsv;
+	}/* end of (else (downstream is a Repeater)) */
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function reads the ksv list from an attached repeater.
+*
+* @param	InstancePtr is the hdcp state machine.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxReadKsvList(XHdcp1x *InstancePtr,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	int NumAttempts = 3;
+	int KsvListIsValid = FALSE;
+	u16 RepeaterInfo = 0;
+
+	/* Determine RepeaterInfo */
+	RepeaterInfo = (u16)(InstancePtr->Tx.StateHelper & 0x1FFFu);
+
+	/* Iterate through the attempts */
+	do {
+		/* Attempt to validate the ksv list */
+		KsvListIsValid =
+			XHdcp1x_TxValidateKsvList(InstancePtr, RepeaterInfo);
+
+		/* Update for loop */
+		NumAttempts--;
+	}
+	while ((NumAttempts > 0) && (!KsvListIsValid));
+
+	/* Check for success */
+	if (KsvListIsValid) {
+		/* Log */
+		XHdcp1x_TxDebugLog(InstancePtr, "ksv list validated");
+
+		/* Check for Repeater */
+		if (InstancePtr->IsRepeater) {
+			/* Set the Repeater information to be
+			* passes to HDCP RX setup */
+			XHdcp1x_TxSetRepeaterInfo(InstancePtr);
+		}
+
+		/* Set the downstream ready variable to 1, as Tx is now
+		* authenticated and call back the RX
+		*/
+		InstancePtr->Tx.DownstreamReady = 1;
+
+		/* Update NextStatePtr */
+		*NextStatePtr = XHDCP1X_STATE_AUTHENTICATED;
+	}
+	else {
+		/* Log */
+		XHdcp1x_TxDebugLog(InstancePtr, "ksv list invalid");
+
+		/* Update NextStatePtr */
+		*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "disabled" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunDisabledState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For enable */
+		case XHDCP1X_EVENT_ENABLE:
+			*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+			if ((InstancePtr->Tx.Flags & XVPHY_FLAG_PHY_UP) == 0) {
+				*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			}
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			InstancePtr->Tx.Flags &= ~XVPHY_FLAG_PHY_UP;
+			break;
+
+		/* For physical layer up */
+		case XHDCP1X_EVENT_PHYUP:
+			InstancePtr->Tx.Flags |= XVPHY_FLAG_PHY_UP;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "determine rx capable" state of the transmit state
+* machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunDetermineRxCapableState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "exchange ksvs" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunExchangeKsvsState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "computations" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunComputationsState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For poll */
+		case XHDCP1X_EVENT_POLL:
+			XHdcp1x_TxPollForComputations(InstancePtr,
+					NextStatePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "validate-rx" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunValidateRxState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For timeout */
+		case XHDCP1X_EVENT_TIMEOUT:
+			XHdcp1x_TxDebugLog(InstancePtr, "validate-rx timeout");
+			XHdcp1x_TxValidateRx(InstancePtr, NextStatePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "authenticated" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunAuthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For check */
+		case XHDCP1X_EVENT_CHECK:
+			*NextStatePtr = XHDCP1X_STATE_LINKINTEGRITYCHECK;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "link-integrity check" state of the transmit state
+* machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunLinkIntegrityCheckState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For poll */
+		case XHDCP1X_EVENT_POLL:
+			XHdcp1x_TxCheckLinkIntegrity(InstancePtr,
+						NextStatePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "test-for-repeater" state of the transmit state
+* machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunTestForRepeaterState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For poll */
+		case XHDCP1X_EVENT_POLL:
+			XHdcp1x_TxTestForRepeater(InstancePtr, NextStatePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "wait-for-ready" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunWaitForReadyState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For poll */
+		case XHDCP1X_EVENT_POLL:
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			/* Don't read the Repeater info for HDMI from a
+			 * poll from application. We'll poll every 100ms. */
+#else
+			/* Attempt to read the repeater info */
+			XHdcp1x_TxPollForWaitForReady(InstancePtr,
+				NextStatePtr);
+#endif
+			break;
+
+		/* For reading the READY bit in BStatus register of the
+		 * attached downstream device.
+		 */
+		case XHDCP1X_EVENT_READDOWNSTREAM:
+			XHdcp1x_TxPollForWaitForReady(InstancePtr,
+				NextStatePtr);
+			break;
+
+		/* For timeout */
+		case XHDCP1X_EVENT_TIMEOUT:
+			XHdcp1x_TxDebugLog(InstancePtr,
+					"wait-for-ready timeout");
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			InstancePtr->Tx.WaitForReadyPollCntFlag++;
+			XHdcp1x_TxStopTimer(InstancePtr);
+			XHdcp1x_TxPollForWaitForReady(InstancePtr,
+						      NextStatePtr);
+			if (InstancePtr->Tx.WaitForReadyPollCntFlag >
+					XHDCP1X_MAX_BCAPS_RDY_POLL_CNT) {
+				*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+				InstancePtr->Tx.WaitForReadyPollCntFlag = 0;
+			} else {
+				if (*NextStatePtr == XHDCP1X_STATE_READKSVLIST ||
+				    *NextStatePtr == XHDCP1X_STATE_UNAUTHENTICATED) {
+					/* Do nothing, timer
+					 * is already stopped */
+				} else {
+					XHdcp1x_TxStartTimer(InstancePtr, XVPHY_TMO_100MS);
+				}
+			}
+#else
+			/* Poll on DisplayPort to check
+			 * if the READY bit is set. */
+			XHdcp1x_TxPollForWaitForReady(InstancePtr,
+						      NextStatePtr);
+			if (*NextStatePtr == XHDCP1X_STATE_WAITFORREADY) {
+				*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+			}
+#endif
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "read-ksv-list" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunReadKsvListState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* InstancePtr not being used */
+	UNUSED(InstancePtr);
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		/* For timeout event */
+		case XHDCP1X_EVENT_TIMEOUT:
+			/* Do nothing */
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "unauthenticated" state of the transmit state machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunUnauthenticatedState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For authenticate */
+		case XHDCP1X_EVENT_AUTHENTICATE:
+			XHdcp1x_TxStartTimer(InstancePtr, XVPHY_TMO_100MS);
+			break;
+
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_EVENT_PHYDOWN:
+			*NextStatePtr = XHDCP1X_STATE_PHYDOWN;
+			break;
+
+		case XHDCP1X_EVENT_TIMEOUT:
+			*NextStatePtr = XHDCP1X_STATE_DETERMINERXCAPABLE;
+			XHdcp1x_TxStopTimer(InstancePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function runs the "physical-layer-down" state of the transmit state
+* machine.
+*
+* @param	InstancePtr is the transmitter instance.
+* @param	Event is the event to process.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxRunPhysicalLayerDownState(XHdcp1x *InstancePtr,
+		XHdcp1x_EventType Event, XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		/* For disable */
+		case XHDCP1X_EVENT_DISABLE:
+			*NextStatePtr = XHDCP1X_STATE_DISABLED;
+			break;
+
+		/* For physical layer up */
+		case XHDCP1X_EVENT_PHYUP:
+			*NextStatePtr = XHDCP1X_STATE_UNAUTHENTICATED;
+			if (InstancePtr->Tx.EncryptionMap != 0) {
+				XHdcp1x_TxPostEvent(InstancePtr,
+					XHDCP1X_EVENT_AUTHENTICATE);
+			}
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function enters a state.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	State is the state to enter.
+* @param	NextStatePtr is the next state.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxEnterState(XHdcp1x *InstancePtr, XHdcp1x_StateType State,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of state called */
+	switch (State) {
+		/* For the disabled state */
+		case XHDCP1X_STATE_DISABLED:
+			/* Clear auth request pending flag */
+			InstancePtr->Tx.IsAuthReqPending = FALSE;
+			XHdcp1x_TxDisableState(InstancePtr);
+			break;
+
+		/* For determine rx capable */
+		case XHDCP1X_STATE_DETERMINERXCAPABLE:
+			InstancePtr->RepeaterValues.hdcp14_PropagateTopoErrUpstream = FALSE;
+			InstancePtr->Tx.Flags |= XVPHY_FLAG_PHY_UP;
+			XHdcp1x_TxSetCheckLinkState(InstancePtr, FALSE);
+			XHdcp1x_TxDisableEncryptionState(InstancePtr);
+			XHdcp1x_TxCheckRxCapable(InstancePtr, NextStatePtr);
+			break;
+
+		/* For the exchange ksvs state */
+		case XHDCP1X_STATE_EXCHANGEKSVS:
+			InstancePtr->Tx.StateHelper = 0;
+			XHdcp1x_TxExchangeKsvs(InstancePtr, NextStatePtr);
+			break;
+
+		/* For the computations state */
+		case XHDCP1X_STATE_COMPUTATIONS:
+			XHdcp1x_TxStartComputations(InstancePtr,
+						    NextStatePtr);
+			break;
+
+		/* For the validate rx state */
+		case XHDCP1X_STATE_VALIDATERX:
+			InstancePtr->Tx.StateHelper = 0;
+			XHdcp1x_TxStartTimer(InstancePtr, XVPHY_TMO_100MS);
+			break;
+
+		/* For the validate rx state */
+		case XHDCP1X_STATE_TESTFORREPEATER:
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			/* Enable encryption for HDMI (this will come immediately
+			 * after Ro' has been read and successfully compared). */
+			InstancePtr->Tx.EncryptionMap = 0x1;
+			XHdcp1x_TxEnableEncryptionState(InstancePtr);
+#else
+			/* Enable encryption for DP (this will come immediately
+			 * after Ro' has been read and successfully compared). */
+			XHdcp1x_TxEnableEncryptionState(InstancePtr);
+#endif
+			break;
+
+		/* For the wait for ready state */
+		case XHDCP1X_STATE_WAITFORREADY:
+			InstancePtr->Tx.StateHelper = 0;
+
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			InstancePtr->Tx.WaitForReadyPollCntFlag = 0;
+			/* Post the timeout */
+			XHdcp1x_TxPostEvent(InstancePtr, XHDCP1X_EVENT_TIMEOUT);
+#else
+			XHdcp1x_TxStartTimer(InstancePtr,
+					     (5 * XVPHY_TMO_1SECOND));
+#endif
+
+			break;
+
+		/* For the read ksv list state */
+		case XHDCP1X_STATE_READKSVLIST:
+			XHdcp1x_TxReadKsvList(InstancePtr, NextStatePtr);
+			break;
+
+		/* For the authenticated state */
+		case XHDCP1X_STATE_AUTHENTICATED:
+			InstancePtr->Tx.StateHelper = 0;
+
+			if (InstancePtr->Tx.PreviousState !=
+					XHDCP1X_STATE_LINKINTEGRITYCHECK) {
+				InstancePtr->Tx.Stats.AuthPassed++;
+				XHdcp1x_TxSetCheckLinkState(InstancePtr, TRUE);
+				XHdcp1x_TxDebugLog(InstancePtr,
+					"authenticated");
+
+				/* Authenticated callback */
+				if (InstancePtr->Tx.IsAuthenticatedCallbackSet)
+				{
+					/* Clear auth request pending flag */
+					InstancePtr->Tx.IsAuthReqPending = (FALSE);
+
+					InstancePtr->Tx.AuthenticatedCallback
+					(InstancePtr->Tx.AuthenticatedCallbackRef);
+				}
+			}
+
+			if (InstancePtr->IsRepeater == 1) {
+			  if(InstancePtr->Tx.DownstreamReady == 1) {
+			    InstancePtr->Tx.DownstreamReady = 0;
+#if (defined(XPAR_XV_HDMITX_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX_NUM_INSTANCES > 0)) || \
+    (defined(XPAR_XV_HDMITX1_NUM_INSTANCES) && \
+     (XPAR_XV_HDMITX1_NUM_INSTANCES > 0))
+			    /* Do nothing for HDMI. */
+#else
+			    /* In case of DisplayPort , read the Downstream Repeater
+			     * Configuration values, and update the StateHelper flag. */
+			    u32 Buf;
+				XHdcp1x_PortRead(InstancePtr, XHDCP1X_PORT_OFFSET_BINFO,
+							&Buf, XHDCP1X_PORT_SIZE_BINFO);
+				InstancePtr->Tx.StateHelper = (Buf & 0x0000FFFFu);
+#endif
+			    XHdcp1x_TxSetRepeaterInfo(InstancePtr);
+			    if (InstancePtr->Tx.IsRepeaterExchangeCallbackSet)
+			    {
+			      InstancePtr->Tx.RepeaterExchangeCallback(
+			        InstancePtr->Tx.RepeaterExchangeRef);
+			    }
+			  }
+			}
+			break;
+
+		/* For the link integrity check state */
+		case XHDCP1X_STATE_LINKINTEGRITYCHECK:
+			XHdcp1x_TxCheckLinkIntegrity(InstancePtr,
+						NextStatePtr);
+			break;
+
+		/* For the unauthenticated state */
+		case XHDCP1X_STATE_UNAUTHENTICATED:
+			InstancePtr->Tx.Flags &= ~XVPHY_FLAG_IS_REPEATER;
+			InstancePtr->Tx.Flags |= XVPHY_FLAG_PHY_UP;
+			XHdcp1x_TxDisableEncryptionState(InstancePtr);
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_STATE_PHYDOWN:
+			InstancePtr->Tx.Flags &= ~XVPHY_FLAG_PHY_UP;
+			XHdcp1x_TxDisableEncryptionState(InstancePtr);
+			XHdcp1x_CipherDisable(InstancePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function exits a state.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	State is the state to exit.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxExitState(XHdcp1x *InstancePtr, XHdcp1x_StateType State,
+		XHdcp1x_StateType *NextStatePtr)
+{
+	/* Case-wise process the kind of state called */
+	switch (State) {
+		/* For the disabled state */
+		case XHDCP1X_STATE_DISABLED:
+			XHdcp1x_TxEnableState(InstancePtr);
+			break;
+
+		/* For the computations state */
+		case XHDCP1X_STATE_COMPUTATIONS:
+			InstancePtr->Tx.StateHelper = 0;
+			break;
+
+		/* For the validate rx state */
+		case XHDCP1X_STATE_VALIDATERX:
+			XHdcp1x_TxStopTimer(InstancePtr);
+			break;
+
+		/* For the wait for ready state */
+		case XHDCP1X_STATE_WAITFORREADY:
+			if (*NextStatePtr == XHDCP1X_STATE_READKSVLIST ||
+			    *NextStatePtr == XHDCP1X_STATE_UNAUTHENTICATED) {
+				/* Timer already stopped. */
+			} else {
+				XHdcp1x_TxStopTimer(InstancePtr);
+			}
+			break;
+
+		/* For the read ksv list state */
+		case XHDCP1X_STATE_READKSVLIST:
+			InstancePtr->Tx.StateHelper = 0;
+			break;
+
+		/* For physical layer down */
+		case XHDCP1X_STATE_PHYDOWN:
+			XHdcp1x_CipherEnable(InstancePtr);
+			break;
+
+		/* Otherwise */
+		default:
+			/* Do nothing */
+			break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function drives a transmit state machine.
+*
+* @param	InstancePtr is the HDCP state machine.
+* @param	Event is the event to process.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxDoTheState(XHdcp1x *InstancePtr, XHdcp1x_EventType Event)
+{
+	XHdcp1x_StateType NextState = InstancePtr->Tx.CurrentState;
+
+	/* Case-wise process the kind of state called */
+	switch (InstancePtr->Tx.CurrentState) {
+		/* For the disabled state */
+		case XHDCP1X_STATE_DISABLED:
+			XHdcp1x_TxRunDisabledState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For determine rx capable state */
+		case XHDCP1X_STATE_DETERMINERXCAPABLE:
+			XHdcp1x_TxRunDetermineRxCapableState(InstancePtr,
+				Event, &NextState);
+			break;
+
+		/* For exchange ksvs state */
+		case XHDCP1X_STATE_EXCHANGEKSVS:
+			XHdcp1x_TxRunExchangeKsvsState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the computations state */
+		case XHDCP1X_STATE_COMPUTATIONS:
+			XHdcp1x_TxRunComputationsState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the validate rx state */
+		case XHDCP1X_STATE_VALIDATERX:
+			XHdcp1x_TxRunValidateRxState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the authenticated state */
+		case XHDCP1X_STATE_AUTHENTICATED:
+			XHdcp1x_TxRunAuthenticatedState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the link integrity check state */
+		case XHDCP1X_STATE_LINKINTEGRITYCHECK:
+			XHdcp1x_TxRunLinkIntegrityCheckState(InstancePtr,
+				Event, &NextState);
+			break;
+
+		/* For the test for repeater state */
+		case XHDCP1X_STATE_TESTFORREPEATER:
+			XHdcp1x_TxRunTestForRepeaterState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the wait for ready state */
+		case XHDCP1X_STATE_WAITFORREADY:
+			XHdcp1x_TxRunWaitForReadyState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the reads ksv list state */
+		case XHDCP1X_STATE_READKSVLIST:
+			XHdcp1x_TxRunReadKsvListState(InstancePtr, Event,
+				&NextState);
+			break;
+
+		/* For the unauthenticated state */
+		case XHDCP1X_STATE_UNAUTHENTICATED:
+			XHdcp1x_TxRunUnauthenticatedState(InstancePtr,
+				Event, &NextState);
+			break;
+
+		/* For the physical layer down state */
+		case XHDCP1X_STATE_PHYDOWN:
+			XHdcp1x_TxRunPhysicalLayerDownState(InstancePtr,
+				Event, &NextState);
+			break;
+
+		/* Otherwise */
+		default:
+			break;
+	}
+
+	/* Check for state change */
+	while (InstancePtr->Tx.CurrentState != NextState) {
+		/* Perform the state transition */
+		XHdcp1x_TxExitState(InstancePtr,
+				InstancePtr->Tx.CurrentState, &NextState);
+		InstancePtr->Tx.PreviousState = InstancePtr->Tx.CurrentState;
+		InstancePtr->Tx.CurrentState = NextState;
+		XHdcp1x_TxEnterState(InstancePtr, InstancePtr->Tx.CurrentState,
+				&NextState);
+		if( ((InstancePtr->Tx.PreviousState != XHDCP1X_STATE_DISABLED)
+		&& (InstancePtr->Tx.PreviousState != XHDCP1X_STATE_PHYDOWN))
+		&& (InstancePtr->Tx.CurrentState
+			== XHDCP1X_STATE_UNAUTHENTICATED) ){
+			/* Clear auth request pending flag */
+			InstancePtr->Tx.IsAuthReqPending = (FALSE);
+
+			if (InstancePtr->Tx.IsUnauthenticatedCallbackSet) {
+				InstancePtr->Tx.UnauthenticatedCallback(
+				InstancePtr->Tx.UnauthenticatedCallbackRef);
+			}
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function processes the events pending on a state machine.
+*
+* @param	InstancePtr is the receiver instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdcp1x_TxProcessPending(XHdcp1x *InstancePtr)
+{
+	/* Check for any pending events */
+	if (InstancePtr->Tx.PendingEvents != 0) {
+		u16 Pending = InstancePtr->Tx.PendingEvents;
+		XHdcp1x_EventType Event = XHDCP1X_EVENT_NULL;
+
+		/* Update InstancePtr */
+		InstancePtr->Tx.PendingEvents = 0;
+
+		/* Iterate through thePending */
+		do {
+			/* Check for a pending event */
+			if ((Pending & 1u) != 0) {
+				XHdcp1x_TxDoTheState(InstancePtr, Event);
+			}
+
+			/* Update for loop */
+			Pending >>= 1;
+			Event++;
+		}
+		while (Pending != 0);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function converts from a state to a display string.
+*
+* @param	State is the state to convert.
+*
+* @return	The corresponding display string.
+*
+* @note		None.
+*
+******************************************************************************/
+static const char *XHdcp1x_TxStateToString(XHdcp1x_StateType State)
+{
+	const char *String = NULL;
+
+	/* Case-wise process the kind of state called */
+	switch (State) {
+		case XHDCP1X_STATE_DISABLED:
+			String = "disabled";
+			break;
+
+		case XHDCP1X_STATE_DETERMINERXCAPABLE:
+			String = "determine-rx-capable";
+			break;
+
+		case XHDCP1X_STATE_EXCHANGEKSVS:
+			String = "exchange-ksvs";
+			break;
+
+		case XHDCP1X_STATE_COMPUTATIONS:
+			String = "computations";
+			break;
+
+		case XHDCP1X_STATE_VALIDATERX:
+			String = "validate-rx";
+			break;
+
+		case XHDCP1X_STATE_AUTHENTICATED:
+			String = "authenticated";
+			break;
+
+		case XHDCP1X_STATE_LINKINTEGRITYCHECK:
+			String = "link-integrity-check";
+			break;
+
+		case XHDCP1X_STATE_TESTFORREPEATER:
+			String = "test-for-repeater";
+			break;
+
+		case XHDCP1X_STATE_WAITFORREADY:
+			String = "wait-for-ready";
+			break;
+
+		case XHDCP1X_STATE_READKSVLIST:
+			String = "read-ksv-list";
+			break;
+
+		case XHDCP1X_STATE_UNAUTHENTICATED:
+			String = "unauthenticated";
+			break;
+
+		case XHDCP1X_STATE_PHYDOWN:
+			String = "physical-layer-down";
+			break;
+
+		default:
+			String = "unknown?";
+			break;
+	}
+
+	return (String);
+}
+
+#if XHDCP1X_ADDITIONAL_DEBUG
+/*****************************************************************************/
+/**
+* This function converts from a state to a display string.
+*
+* @param	Event is the event to convert.
+*
+* @return	The corresponding display string.
+*
+* @note		None.
+*
+******************************************************************************/
+static const char *XHdcp1x_TxEventToString(XHdcp1x_EventType Event)
+{
+	const char *String = NULL;
+
+	/* Case-wise process the kind of event called */
+	switch (Event) {
+		case 	XHDCP1X_EVENT_NULL:
+			String = "null";
+			break;
+
+		case 	XHDCP1X_EVENT_AUTHENTICATE:
+			String = "authenticate";
+			break;
+
+		case	XHDCP1X_EVENT_CHECK:
+			String = "check";
+			break;
+
+		case	XHDCP1X_EVENT_DISABLE:
+			String = "disable";
+			break;
+
+		case	XHDCP1X_EVENT_ENABLE:
+			String = "enable";
+			break;
+
+		case	XHDCP1X_EVENT_LINKDOWN:
+			String = "link-down";
+			break;
+
+		case	XHDCP1X_EVENT_PHYDOWN:
+			String = "phy-down";
+			break;
+
+		case	XHDCP1X_EVENT_PHYUP:
+			String = "phy-up";
+			break;
+
+		case	XHDCP1X_EVENT_POLL:
+			String = "poll";
+			break;
+
+		case	XHDCP1X_EVENT_TIMEOUT:
+			String = "timeout";
+			break;
+
+		case	XHDCP1X_EVENT_READDOWNSTREAM:
+			String = "read-downstream";
+			break;
+
+		default:
+			String = "unknown?";
+			break;
+	}
+
+	return (String);
+}
+#endif
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_tx.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp1x_tx.h
@@ -0,0 +1,125 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp1x_tx.h
+* @{
+*
+* This file provides the interface of the HDCP TX state machine
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  fidus  07/16/15 Initial release.
+* 1.10  MG     01/18/16 Added function XHdcp1x_TxIsEnabled.
+* 1.20  MG     02/25/16 Added function XHdcp1x_TxSetCallback.
+* 3.0   yas    02/13/16 Upgraded to support HDCP Repeater functionality.
+*                       Added the following functions:
+*                       XHdcp1x_TxReadDownstream, XHdcp1x_TxSetCallBack,
+*                       XHdcp1x_TxTriggerDownstreamAuth.
+* 3.1   yas    06/15/16 Repeater functionality extended to support HDMI.
+*                       Added fucntions,
+*                       XHdcp1x_TxIsInComputations,XHdcp1x_TxIsInWaitforready,
+*                       XHdcp1x_TxIsDownstrmCapable, XHdcp1x_TxIsRepeater,
+*                       XHdcp1x_TxEnableBlank, XHdcp1x_TxDisableBlank,
+*                       XHdcp1x_TxGetTopologyKSVList,
+*                       XHdcp1x_TxGetTopologyDepth,
+*                       XHdcp1x_TxGetTopologyDeviceCnt,
+*                       XHdcp1x_TxGetTopologyMaxCascadeExceeded,
+*                       XHdcp1x_TxGetTopologyBKSV,
+*                       XHdcp1x_TxGetTopologyMaxDevsExceeded,
+*                       XHdcp1x_TxGetTopology
+* 4.1   yas    22/04/16 Added function XHdcp1x_TxSetHdmiMode.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP1X_TX_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP1X_TX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp1x.h"
+
+#include "xstatus.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Prototypes ******************************/
+
+void XHdcp1x_TxInit(XHdcp1x *InstancePtr);
+int XHdcp1x_TxSetCallback(XHdcp1x *InstancePtr,
+	XHdcp1x_HandlerType HandlerType, void *CallbackFunc,
+	void *CallbackRef);
+
+int XHdcp1x_TxPoll(XHdcp1x *InstancePtr);
+
+int XHdcp1x_TxReset(XHdcp1x *InstancePtr);
+int XHdcp1x_TxEnable(XHdcp1x *InstancePtr);
+int XHdcp1x_TxDisable(XHdcp1x *InstancePtr);
+
+int XHdcp1x_TxIsDownstrmCapable(const XHdcp1x *InstancePtr);
+u64 XHdcp1x_TxGetEncryption(const XHdcp1x *InstancePtr);
+int XHdcp1x_TxEnableEncryption(XHdcp1x *InstancePtr, u64 StreamMap);
+int XHdcp1x_TxDisableEncryption(XHdcp1x *InstancePtr, u64 StreamMap);
+void XHdcp1x_TxSetHdmiMode(XHdcp1x *InstancePtr, u8 Value);
+
+int XHdcp1x_TxSetPhysicalState(XHdcp1x *InstancePtr, int IsUp);
+int XHdcp1x_TxSetLaneCount(XHdcp1x *InstancePtr, int LaneCount);
+
+int XHdcp1x_TxAuthenticate(XHdcp1x *InstancePtr);
+int XHdcp1x_TxReadDownstream(XHdcp1x *InstancePtr);
+int XHdcp1x_TxIsInProgress(const XHdcp1x *InstancePtr);
+int XHdcp1x_TxIsAuthenticated(const XHdcp1x *InstancePtr);
+int XHdcp1x_TxIsInComputations(const XHdcp1x *InstancePtr);
+int XHdcp1x_TxIsInWaitforready(const XHdcp1x *InstancePtr);
+int XHdcp1x_TxIsEnabled(const XHdcp1x *InstancePtr);
+void XHdcp1x_TxHandleTimeout(XHdcp1x *InstancePtr);
+
+int XHdcp1x_TxInfo(const XHdcp1x *InstancePtr);
+void XHdcp1x_TxTriggerDownstreamAuth(void *Parameter);
+
+void XHdcp1x_TxEnableBlank(XHdcp1x *InstancePtr);
+void XHdcp1x_TxDisableBlank(XHdcp1x *InstancePtr);
+int XHdcp1x_TxIsRepeater(XHdcp1x *InstancePtr);
+
+XHdcp1x_RepeaterExchange *XHdcp1x_TxGetTopology(XHdcp1x *InstancePtr);
+u32 XHdcp1x_TxGetTopologyMaxDevsExceeded(XHdcp1x *InstancePtr);
+u8 *XHdcp1x_TxGetTopologyBKSV(XHdcp1x *InstancePtr);
+u32 XHdcp1x_TxGetTopologyMaxCascadeExceeded(XHdcp1x *InstancePtr);
+u32 XHdcp1x_TxGetTopologyDeviceCnt(XHdcp1x *InstancePtr);
+u32 XHdcp1x_TxGetTopologyDepth(XHdcp1x *InstancePtr);
+u8 *XHdcp1x_TxGetTopologyKSVList(XHdcp1x *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP1X_TX_H */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher.c
@@ -0,0 +1,226 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_cipher.c
+* @{
+* @details
+*
+* This file contains the main implementation of the Xilinx HDCP 2.2 Cipher
+* device driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* 1.10  MH     08/04/16 Added 64 bit address support.
+* </pre>
+*
+******************************************************************************/
+
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_cipher.h"
+#include <linux/string.h>
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+
+/************************** Function Definitions *****************************/
+
+
+/*****************************************************************************/
+/**
+*
+* This function initializes the HDCP22 Cipher core. This function must be called
+* prior to using the HDCP22 Cipher core. Initialization of the HDCP22 Cipher includes
+* setting up the instance data, and ensuring the hardware is in a quiescent
+* state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Cipher core instance.
+* @param  CfgPtr points to the configuration structure associated with
+*         the HDCP22 Cipher core core.
+* @param  EffectiveAddr is the base address of the device. If address
+*         translation is being used, then this parameter must reflect the
+*         virtual base address. Otherwise, the physical address should be
+*         used.
+*
+* @return
+*   - XST_SUCCESS if XHdcp22Cipher_CfgInitialize was successful.
+*   - XST_FAILURE if HDCP22 Cipher ID mismatched.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp22Cipher_CfgInitialize(XHdcp22_Cipher *InstancePtr,
+                                XHdcp22_Cipher_Config *CfgPtr,
+                                UINTPTR EffectiveAddr)
+{
+	u32 RegValue;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+	Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+	/* Setup the instance */
+	(void)memset((void *)InstancePtr, 0, sizeof(XHdcp22_Cipher));
+	(void)memcpy((void *)&(InstancePtr->Config), (const void *)CfgPtr, sizeof(XHdcp22_Cipher_Config));
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+
+	/* Check ID */
+	RegValue = XHdcp22Cipher_ReadReg(InstancePtr->Config.BaseAddress, (XHDCP22_CIPHER_VER_ID_OFFSET));
+	RegValue = ((RegValue) >> (XHDCP22_CIPHER_SHIFT_16)) & (XHDCP22_CIPHER_MASK_16);
+	if (RegValue != (XHDCP22_CIPHER_VER_ID)) {
+		return (XST_FAILURE);
+	}
+
+	/* Reset the hardware and set the flag to indicate the driver is ready */
+	InstancePtr->IsReady = (u32)(XIL_COMPONENT_IS_READY);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the Ks key in the HDCP22 Cipher core.
+*
+* @param  BaseAddress is the base address of the HDCP22 Cipher core instance.
+* @param  KsPtr is a pointer to the Ks key.
+* @param  Length indicates the number of bytes.
+*
+* @return None.
+*
+* @note   The Ks should be in big endian notation.
+*
+******************************************************************************/
+void XHdcp22Cipher_SetKs(XHdcp22_Cipher *InstancePtr, const u8 *KsPtr, u16 Length)
+{
+	Xil_AssertVoid(KsPtr != NULL);
+	Xil_AssertVoid(Length == 16);
+
+	u32 i = 0;
+	u32* U32Ptr = NULL;
+	u32 Offset = XHDCP22_CIPHER_REG_KS_1_OFFSET;
+
+
+	u8 Buf[16] __attribute__((aligned(sizeof(u32))));
+	/* The HDCP cipher expects the Ks to be written in little endian format */
+	/* Swap the endianess */
+	for (i=0; i<16; i++){
+		Buf[(15-i)] = KsPtr[i];
+	}
+
+	/* KsPtr contains 16 bytes (128 bits). Map to 4 u32 values for writing */
+	for (i=0; i<Length; i+=4)
+	{
+		U32Ptr = (u32 *)&Buf[i];
+		XHdcp22Cipher_WriteReg(InstancePtr->Config.BaseAddress, Offset, *U32Ptr);
+		/* Increase offset to the next register */
+		Offset+=4;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the Lc128 key in the HDCP22 Cipher core.
+*
+* @param  BaseAddress is the base address of the HDCP22 Cipher core instance.
+* @param  Lc128Ptr is a pointer to the LC128 key.
+* @param  Length indicates the number of bytes.
+*
+* @return None.
+*
+* @note   The Lc128 should be in big endian notation.
+*
+******************************************************************************/
+void XHdcp22Cipher_SetLc128(XHdcp22_Cipher *InstancePtr, const u8 *Lc128Ptr,  u16 Length)
+{
+	Xil_AssertVoid(Lc128Ptr != NULL);
+	Xil_AssertVoid(Length == 16);
+
+	u32 i = 0;
+	u32* U32Ptr = NULL;
+	u32 Offset = XHDCP22_CIPHER_REG_LC128_1_OFFSET;
+
+	u8 Buf[16] __attribute__((aligned(sizeof(u32))));
+	/* The HDCP cipher expects the Ks to be written in little endian format */
+	/* Swap the endianess */
+	for (i=0; i<16; i++){
+		Buf[(15-i)] = Lc128Ptr[i];
+	}
+
+	/* Lc128Ptr contains 16 bytes (128 bits). Map to 4 u32 values for writing */
+	for (i=0; i<Length; i+=4)
+	{
+		U32Ptr = (u32 *)&Buf[i];
+		XHdcp22Cipher_WriteReg(InstancePtr->Config.BaseAddress, Offset, *U32Ptr);
+		/* Increase offset to the next register */
+		Offset+=4;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the Riv key in the HDCP22 Cipher core.
+*
+* @param  BaseAddress is the base address of the HDCP22 Cipher core instance.
+* @param  RivPtr is a pointer to the Riv key.
+* @param  Length indicates the number of bytes.
+*
+* @return None.
+*
+* @note   The Riv should be in big endian notation.
+*
+******************************************************************************/
+void XHdcp22Cipher_SetRiv(XHdcp22_Cipher *InstancePtr, const u8 *RivPtr,  u16 Length)
+{
+	Xil_AssertVoid(RivPtr != NULL);
+	Xil_AssertVoid(Length == 8);
+
+	u32 i = 0;
+	u32* U32Ptr = NULL;
+	u32 Offset = XHDCP22_CIPHER_REG_RIV_1_OFFSET;
+
+	u8 Buf[8] __attribute__((aligned(sizeof(u32))));
+	/* The HDCP cipher expects the Riv to be written in little endian format */
+	/* Swap the endianess */
+	for (i=0; i<8; i++)
+	{
+		Buf[(7-i)] = RivPtr[i];
+	}
+
+	/* RivPtr contains 8 bytes (64 bits). Map to 2 u32 values for writing */
+	for (i=0; i<Length; i+=4)
+	{
+		U32Ptr = (u32 *)&Buf[i];
+		XHdcp22Cipher_WriteReg(InstancePtr->Config.BaseAddress, Offset, *U32Ptr);
+		/* Increase offset to the next register */
+		Offset+=4;
+	}
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher.h
@@ -0,0 +1,344 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_cipher.h
+* @{
+* @details
+*
+* This is the main header file of the Xilinx HDCP 2.2 Cipher device driver.
+* The Cipher implements the AES-128 standard for encrypting and decrypting
+* audiovisual content. The Cipher is required to be programmed with the
+* global constant Lc128, random number Riv, and session key Ks before encryption
+* is enabled. Internally, the cipher uses the Enhanced Encryption Signaling
+* Status (EESS) to determine when to encrypt and decrypt frames. It also
+* manages the data and frame counters to ensure the transmitter and receiver
+* Ciphers are synchronized.
+*
+* <b>Software Initialization and Configuration</b>
+*
+* The application needs to do the following steps to run the Cipher.
+* - Call XHdcp22Cipher_LookupConfig using the device ID to find the
+*   core configuration instance.
+* - Call XHdcp22Cipher_CfgInitialize to intitialize the device instance.
+* - Call XHdcp22Cipher_SetTxMode or XHdcp22Cipher_SetRxMode to setup
+*   the Cipher as either a transmitter or receiver.
+* - Call XHdcp22Cipher_Enable to enable the cipher.
+* - Call XHdcp22Cipher_SetLc128 to program the Lc128 constant.
+* - Call XHdcp22Cipher_SetRiv to program the random number Riv.
+* - Call XHdcp22Cipher_SetKs to program the session key Ks.
+* - If operating as a transmitter call XHdcp22Cipher_EnableTxEncryption
+*   to enable encryption or XHdcp22Cipher_DisableTxEncryption to
+*   disable encryption.
+*
+* <b>Interrupts</b>
+*
+* None.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* 1.01  MG     10/28/15 Added Noise and blank macros
+* 1.02  MG     02/25/15 Added GetVersion macro
+* 1.03  MH     08/04/16 Added 64 bit address support.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP22_CIPHER_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP22_CIPHER_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_cipher_hw.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/**
+* This typedef contains configuration information for the HDCP22 Cipher core.
+* Each HDCP22 Cipher device should have a configuration structure associated.
+*/
+typedef struct {
+	u16 DeviceId;     /**< DeviceId is the unique ID of the HDCP22 Cipher core */
+	UINTPTR BaseAddress;  /**< BaseAddress is the physical base address of the core's registers */
+} XHdcp22_Cipher_Config;
+
+/**
+* The XHdcp22 Cipher driver instance data. An instance must be allocated for each
+* HDCP22 Cipher core in use.
+*/
+typedef struct {
+	XHdcp22_Cipher_Config Config; /**< Hardware Configuration */
+	u32 IsReady;                  /**< Core and the driver instance are initialized */
+} XHdcp22_Cipher;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_Enable(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_Enable(InstancePtr) \
+        XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_CIPHER_REG_CTRL_SET_OFFSET),(XHDCP22_CIPHER_REG_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_Disable(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_Disable(InstancePtr) \
+        XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_CIPHER_REG_CTRL_CLR_OFFSET), (XHDCP22_CIPHER_REG_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the encrypted enabled state of the HDCP22 Cipher core
+* instance.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return TRUE if HDCP22 cipher is enabled, FALSE otherwise.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Cipher_IsEnabled(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_IsEnabled(InstancePtr) \
+        ((XHdcp22Cipher_GetControlReg((InstancePtr)->Config.BaseAddress)\
+        & XHDCP22_CIPHER_REG_CTRL_RUN_MASK) ==  XHDCP22_CIPHER_REG_CTRL_RUN_MASK)
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the HDCP operation mode for the HDCP22 Cipher peripheral.
+* The mode
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_SetTxMode(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_SetTxMode(InstancePtr) \
+        XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_CIPHER_REG_CTRL_CLR_OFFSET), (XHDCP22_CIPHER_REG_CTRL_MODE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the HDCP RX operation mode for the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_SetRxMode(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_SetRxMode(InstancePtr) \
+        XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_CIPHER_REG_CTRL_SET_OFFSET), (XHDCP22_CIPHER_REG_CTRL_MODE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables HDCP TX encryption for the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_EnableTxEncryption(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_EnableTxEncryption(InstancePtr) \
+        XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_CIPHER_REG_CTRL_SET_OFFSET), (XHDCP22_CIPHER_REG_CTRL_ENCRYPT_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables HDCP TX encryption for the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_DisableTxEncryption(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_DisableTxEncryption(InstancePtr) \
+        XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_CIPHER_REG_CTRL_CLR_OFFSET), (XHDCP22_CIPHER_REG_CTRL_ENCRYPT_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the encrypted enabled state of HDCP TX encryption
+* for the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return TRUE if HDCP22 TX encryption is enabled, FALSE otherwise.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Cipher_IsTxEncryptionEnabled(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_IsTxEncryptionEnabled(InstancePtr) \
+        ((XHdcp22Cipher_GetControlReg((InstancePtr)->Config.BaseAddress)\
+        & XHDCP22_CIPHER_REG_CTRL_ENCRYPT_MASK) ==  XHDCP22_CIPHER_REG_CTRL_ENCRYPT_MASK)
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the encrypted state for the HDCP22 Cipher peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return TRUE if the frame is encrypted, FALSE otherwise.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_DisableTxEncryption(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_IsEncrypted(InstancePtr) \
+        ((XHdcp22Cipher_GetStatusReg((InstancePtr)->Config.BaseAddress) \
+        & XHDCP22_CIPHER_REG_STA_ENCRYPTED_MASK) ==  XHDCP22_CIPHER_REG_STA_ENCRYPTED_MASK)
+
+/*****************************************************************************/
+/**
+*
+* This macro enables or disables noise output for the HDCP22 Cipher
+* peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+* @param  Set specifies TRUE/FALSE either to enable/disable noise output.
+*
+* @return none.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_Noise(u32 BaseAddress, u8 Set)
+*
+******************************************************************************/
+#define XHdcp22Cipher_Noise(InstancePtr, Set) \
+{ \
+        if (Set) { \
+                XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, (XHDCP22_CIPHER_REG_CTRL_SET_OFFSET), (XHDCP22_CIPHER_REG_CTRL_NOISE_MASK)); \
+        } \
+        else { \
+                XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, (XHDCP22_CIPHER_REG_CTRL_CLR_OFFSET), (XHDCP22_CIPHER_REG_CTRL_NOISE_MASK)); \
+        } \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro enables or disables blank screen for the HDCP22 Cipher
+* peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+* @param  Set specifies TRUE/FALSE either to enable/disable blank screen.
+*
+* @return none.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_Blank(u32 BaseAddress, u8 Set)
+*
+******************************************************************************/
+#define XHdcp22Cipher_Blank(InstancePtr, Set) \
+{ \
+        if (Set) { \
+                XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, (XHDCP22_CIPHER_REG_CTRL_SET_OFFSET), (XHDCP22_CIPHER_REG_CTRL_BLANK_MASK)); \
+        } \
+        else { \
+                XHdcp22Cipher_WriteReg((InstancePtr)->Config.BaseAddress, (XHDCP22_CIPHER_REG_CTRL_CLR_OFFSET), (XHDCP22_CIPHER_REG_CTRL_BLANK_MASK)); \
+        } \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro reads the version for the HDCP22 Cipher
+* peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 Cipher core instance.
+*
+* @return version.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_GetVersion(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_GetVersion(InstancePtr) \
+        XHdcp22Cipher_ReadReg((InstancePtr)->Config.BaseAddress, XHDCP22_CIPHER_VER_VERSION_OFFSET)
+
+/************************** Function Prototypes ******************************/
+/* Initialization function in xhdcp22_cipher_sinit.c */
+XHdcp22_Cipher_Config *XHdcp22Cipher_LookupConfig(u16 DeviceId);
+
+/* Initialization and control functions in xhdcp22_cipher.c */
+int XHdcp22Cipher_CfgInitialize(XHdcp22_Cipher *InstancePtr, XHdcp22_Cipher_Config *CfgPtr, UINTPTR EffectiveAddr);
+
+void XHdcp22Cipher_SetKs(XHdcp22_Cipher *InstancePtr, const u8 *KsPtr, u16 Length);
+void XHdcp22Cipher_SetLc128(XHdcp22_Cipher *InstancePtr, const u8 *Lc128Ptr,  u16 Length);
+void XHdcp22Cipher_SetRiv(XHdcp22_Cipher *InstancePtr, const u8 *RivPtr,  u16 Length);
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP2_CIPHER_H */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher_hw.h
@@ -0,0 +1,215 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_cipher_hw.h
+* @{
+* @details
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx HDCP 2.2 Cipher core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* 1.01  MG     10/28/15 Added InputCtr register
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP22_CIPHER_HW_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP22_CIPHER_HW_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xil_types.h"
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+/* HDCP22 Cipher Version Interface base */
+#define XHDCP22_CIPHER_VER_BASE             (0*64)
+/** VER Identification register * register offset */
+#define XHDCP22_CIPHER_VER_ID_OFFSET        ((XHDCP22_CIPHER_VER_BASE)+(0*4))
+/** VER Version register * offset */
+#define XHDCP22_CIPHER_VER_VERSION_OFFSET   ((XHDCP22_CIPHER_VER_BASE)+(1*4))
+
+/* HDCP22 Cipher Register peripheral interface base */
+#define XHDCP22_CIPHER_REG_BASE             (1*64)
+/** Control register * register offset */
+#define XHDCP22_CIPHER_REG_CTRL_OFFSET      ((XHDCP22_CIPHER_REG_BASE)+(0*4))
+/** Control set register * offset */
+#define XHDCP22_CIPHER_REG_CTRL_SET_OFFSET  ((XHDCP22_CIPHER_REG_BASE)+(1*4))
+/** Control clear register * offset */
+#define XHDCP22_CIPHER_REG_CTRL_CLR_OFFSET  ((XHDCP22_CIPHER_REG_BASE)+(2*4))
+/** Status register * offset */
+#define XHDCP22_CIPHER_REG_STA_OFFSET       ((XHDCP22_CIPHER_REG_BASE)+(3*4))
+/** Ks register 1 * offset */
+#define XHDCP22_CIPHER_REG_KS_1_OFFSET      ((XHDCP22_CIPHER_REG_BASE)+(4*4))
+/** Ks register 2 * offset */
+#define XHDCP22_CIPHER_REG_KS_2_OFFSET      ((XHDCP22_CIPHER_REG_BASE)+(5*4))
+/** Ks register 3 * offset */
+#define XHDCP22_CIPHER_REG_KS_3_OFFSET      ((XHDCP22_CIPHER_REG_BASE)+(6*4))
+/** Ks register 4 * offset */
+#define XHDCP22_CIPHER_REG_KS_4_OFFSET      ((XHDCP22_CIPHER_REG_BASE)+(7*4))
+/** Lc128 register 1 * offset */
+#define XHDCP22_CIPHER_REG_LC128_1_OFFSET   ((XHDCP22_CIPHER_REG_BASE)+(8*4))
+/** Lc128 register 2 * offset */
+#define XHDCP22_CIPHER_REG_LC128_2_OFFSET   ((XHDCP22_CIPHER_REG_BASE)+(9*4))
+/** Lc128 register 3 * offset */
+#define XHDCP22_CIPHER_REG_LC128_3_OFFSET   ((XHDCP22_CIPHER_REG_BASE)+(10*4))
+/** Lc128 register 4 * offset */
+#define XHDCP22_CIPHER_REG_LC128_4_OFFSET   ((XHDCP22_CIPHER_REG_BASE)+(11*4))
+/** Riv register 1 * offset */
+#define XHDCP22_CIPHER_REG_RIV_1_OFFSET     ((XHDCP22_CIPHER_REG_BASE)+(12*4))
+/** Riv register 2 * offset */
+#define XHDCP22_CIPHER_REG_RIV_2_OFFSET     ((XHDCP22_CIPHER_REG_BASE)+(13*4))
+/** InputCtr register 1 * offset */
+#define XHDCP22_CIPHER_REG_INPUTCTR_1_OFFSET    ((XHDCP22_CIPHER_REG_BASE)+(14*4))
+/** InputCtr register 2 * offset */
+#define XHDCP22_CIPHER_REG_INPUTCTR_2_OFFSET    ((XHDCP22_CIPHER_REG_BASE)+(15*4))
+
+/* HDCP22 Cipher Control register masks */
+/** Control register Run mask */
+#define XHDCP22_CIPHER_REG_CTRL_RUN_MASK        (1<<0)
+/** Control register Interrupt Enable mask. Reserved for future use. */
+#define XHDCP22_CIPHER_REG_CTRL_IE_MASK         (1<<1)
+/** Control register Mode mask */
+#define XHDCP22_CIPHER_REG_CTRL_MODE_MASK       (1<<2)
+/** Control register Encrypt mask */
+#define XHDCP22_CIPHER_REG_CTRL_ENCRYPT_MASK    (1<<3)
+/** Control register blank mask */
+#define XHDCP22_CIPHER_REG_CTRL_BLANK_MASK    	(1<<4)
+/** Control register noise mask */
+#define XHDCP22_CIPHER_REG_CTRL_NOISE_MASK    	(1<<5)
+
+/* HDCP22 Cipher Status register masks */
+/** Status register interrupt mask. Reserved for future use.*/
+#define XHDCP22_CIPHER_REG_STA_IRQ_MASK         (1<<0)
+/** Status register event mask. Reserved for future use.*/
+#define XHDCP22_CIPHER_REG_STA_EVT_MASK         (1<<1)
+/** Status register encrypted mask. */
+#define XHDCP22_CIPHER_REG_STA_ENCRYPTED_MASK   (1<<2)
+
+/* Peripheral ID and General shift values. */
+#define XHDCP22_CIPHER_SHIFT_16               16      /**< 16 shift value */
+#define XHDCP22_CIPHER_MASK_16                0xFFFF  /**< 16 bit mask value */
+#define XHDCP22_CIPHER_VER_ID                 0x2200  /**< Version ID */
+
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/** @name Register access macro definition
+* @{
+*/
+#define XHdcp22Cipher_In32        Xil_In32        /**< Input Operations */
+#define XHdcp22Cipher_Out32       Xil_Out32       /**< Output Operations */
+
+/*****************************************************************************/
+/**
+*
+* This macro reads a value from a HDCP22 Cipher register.
+* A 32 bit read is performed.
+* If the component is implemented in a smaller width, only the least
+* significant data is read from the register. The most significant data
+* will be read as 0.
+*
+* @param  BaseAddress is the base address of the HDCP22 Cipher core instance.
+* @param  RegOffset is the register offset of the register (defined at
+*         the top of this file).
+*
+* @return The 32-bit value of the register.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Cipher_ReadReg(u32 BaseAddress, u32 RegOffset)
+*
+******************************************************************************/
+#define XHdcp22Cipher_ReadReg(BaseAddress, RegOffset) \
+        XHdcp22Cipher_In32((BaseAddress) + ((u32)RegOffset))
+
+/*****************************************************************************/
+/**
+*
+* This macro writes a value to a HDCP22 Cipher register.
+* A 32 bit write is performed. If the component is implemented in a smaller
+* width, only the least significant data is written.
+*
+* @param  BaseAddress is the base address of the HDCP22 Cipher core instance.
+* @param  RegOffset is the register offset of the register (defined at
+*         the top of this file) to be written.
+* @param  Data is the 32-bit value to write into the register.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Cipher_WriteReg(u32 BaseAddress, u32 RegOffset, u32 Data)
+*
+******************************************************************************/
+#define XHdcp22Cipher_WriteReg(BaseAddress, RegOffset, Data) \
+        XHdcp22Cipher_Out32((BaseAddress) + ((u32)RegOffset), (u32)(Data))
+/*****************************************************************************/
+/**
+*
+* This macro reads the status register from the HDCP22 Cipher.
+*
+* @param  IBaseAddress is the base address of the HDCP22 Cipher core instance.
+*
+* @return A 32-bit value representing the contents of the status register.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Cipher_GetStatusReg(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_GetStatusReg(BaseAddress) \
+        XHdcp22Cipher_ReadReg(BaseAddress, XHDCP22_CIPHER_REG_STA_OFFSET)
+
+/*****************************************************************************/
+/**
+*
+* This macro reads the control register from the HDCP22 Cipher.
+*
+* @param  BaseAddress is the base address of the HDCP22 Cipher core instance.
+*
+* @return A 32-bit value representing the contents of the control register.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Cipher_GetStatusReg(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Cipher_GetControlReg(BaseAddress) \
+        XHdcp22Cipher_ReadReg(BaseAddress, XHDCP22_CIPHER_REG_CTRL_OFFSET)
+/*@}*/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP2_CIPHER_HW_H */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_cipher_sinit.c
@@ -0,0 +1,96 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_cipher_sinit.c
+* @{
+* @details
+*
+* This file contains the static initialization methods for the Xilinx
+* HDCP 2.2 Cipher core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_cipher.h"
+
+
+/************************** Constant Definitions *****************************/
+#ifndef XPAR_XHDCP22_CIPHER_NUM_INSTANCES
+#define XPAR_XHDCP22_CIPHER_NUM_INSTANCES 0
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+extern XHdcp22_Cipher_Config XHdcp22_Cipher_ConfigTable[];
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XHdcp22_Cipher_Config structure based
+* on the core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xhdcp22_cipher_g.c file.
+*
+* @param  DeviceId is the unique core ID of the XHDCP22 Cipher core for the
+*         lookup operation.
+*
+* @return XHdcp22Cipher_LookupConfig returns a reference to a config record
+*         in the configuration table (in xhdcp22_cipher_g.c) corresponding
+*         to <i>DeviceId</i>, or NULL if no match is found.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdcp22_Cipher_Config *XHdcp22Cipher_LookupConfig(u16 DeviceId)
+{
+
+	XHdcp22_Cipher_Config *CfgPtr = NULL;
+	u32 Index;
+
+	/* Checking for device id for which instance it is matching */
+	for (Index = (u32)0x0; Index < (u32)(XPAR_XHDCP22_CIPHER_NUM_INSTANCES);
+		Index++) {
+
+		/* Assigning address of config table if both device ids
+		 * are matched
+		 */
+		if (XHdcp22_Cipher_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XHdcp22_Cipher_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return (XHdcp22_Cipher_Config *)CfgPtr;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_common.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_common.h
@@ -0,0 +1,62 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file xhdcp22_common.h
+*
+* This file contains common functions shared between HDCP22 drivers.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release.
+* 1.01  MH   01/15/16 Added prefix to function names.
+* 2.00  MH   06/21/17 Changed DIGIT_T type to u32 for ARM support.
+*</pre>
+*
+*****************************************************************************/
+
+#ifndef XHDCP22_COMMON_H_
+#define XHDCP22_COMMON_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files ********************************/
+#include "bigdigits.h"
+
+/************************** Constant Definitions ****************************/
+
+/**************************** Type Definitions ******************************/
+
+/***************** Macros (Inline Functions) Definitions ********************/
+
+/************************** Function Prototypes *****************************/
+
+/* Cryptographic functions */
+void XHdcp22Cmn_Sha256Hash(const u8 *Data, u32 DataSize, u8 *HashedData);
+int  XHdcp22Cmn_HmacSha256Hash(const u8 *Data, int DataSize, const u8 *Key, int KeySize, u8  *HashedData);
+void XHdcp22Cmn_Aes128Encrypt(const u8 *Data, const u8 *Key, u8 *Output);
+void XHdcp22Cmn_Aes128Decrypt(const u8 *Data, const u8 *Key, u8 *Output);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP22_COMMON_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult.c
@@ -0,0 +1,639 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_mmult.c
+* @{
+* @details
+*
+* This file contains the main implementation of the driver associated with
+* the Xilinx HDCP 2.2 Montgomery Multiplier core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  MH     12/07/15 Initial release.
+* 1.01  MH     08/04/16 Added 64 bit address support.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_mmult.h"
+
+/************************** Function Implementation *************************/
+#if (defined(__KERNEL__) || (!defined(__linux__)))
+int XHdcp22_mmult_CfgInitialize(XHdcp22_mmult *InstancePtr, XHdcp22_mmult_Config *ConfigPtr, UINTPTR EffectiveAddr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(ConfigPtr != NULL);
+    Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+    InstancePtr->Config.BaseAddress = EffectiveAddr;
+    InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+
+    return XST_SUCCESS;
+}
+#endif
+
+void XHdcp22_mmult_Start(XHdcp22_mmult *InstancePtr) {
+    u32 Data;
+
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    Data = XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL) & 0x80;
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL, Data | 0x01);
+}
+
+u32 XHdcp22_mmult_IsDone(XHdcp22_mmult *InstancePtr) {
+    u32 Data;
+
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    Data = XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL);
+    return (Data >> 1) & 0x1;
+}
+
+u32 XHdcp22_mmult_IsIdle(XHdcp22_mmult *InstancePtr) {
+    u32 Data;
+
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    Data = XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL);
+    return (Data >> 2) & 0x1;
+}
+
+u32 XHdcp22_mmult_IsReady(XHdcp22_mmult *InstancePtr) {
+    u32 Data;
+
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    Data = XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL);
+    // check ap_start to see if the pcore is ready for next input
+    return !(Data & 0x1);
+}
+
+void XHdcp22_mmult_EnableAutoRestart(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL, 0x80);
+}
+
+void XHdcp22_mmult_DisableAutoRestart(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_AP_CTRL, 0);
+}
+
+u32 XHdcp22_mmult_Get_U_BaseAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_U_BASE);
+}
+
+u32 XHdcp22_mmult_Get_U_HighAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_U_HIGH);
+}
+
+u32 XHdcp22_mmult_Get_U_TotalBytes(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (XHDCP22_MMULT_CTRL_ADDR_U_HIGH - XHDCP22_MMULT_CTRL_ADDR_U_BASE + 1);
+}
+
+u32 XHdcp22_mmult_Get_U_BitWidth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_WIDTH_U;
+}
+
+u32 XHdcp22_mmult_Get_U_Depth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_DEPTH_U;
+}
+
+u32 XHdcp22_mmult_Write_U_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_U_HIGH - XHDCP22_MMULT_CTRL_ADDR_U_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_U_BASE + (offset + i)*4) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_U_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_U_HIGH - XHDCP22_MMULT_CTRL_ADDR_U_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_U_BASE + (offset + i)*4);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Write_U_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_U_HIGH - XHDCP22_MMULT_CTRL_ADDR_U_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_U_BASE + offset + i) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_U_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_U_HIGH - XHDCP22_MMULT_CTRL_ADDR_U_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_U_BASE + offset + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Get_A_BaseAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_A_BASE);
+}
+
+u32 XHdcp22_mmult_Get_A_HighAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_A_HIGH);
+}
+
+u32 XHdcp22_mmult_Get_A_TotalBytes(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (XHDCP22_MMULT_CTRL_ADDR_A_HIGH - XHDCP22_MMULT_CTRL_ADDR_A_BASE + 1);
+}
+
+u32 XHdcp22_mmult_Get_A_BitWidth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_WIDTH_A;
+}
+
+u32 XHdcp22_mmult_Get_A_Depth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_DEPTH_A;
+}
+
+u32 XHdcp22_mmult_Write_A_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_A_HIGH - XHDCP22_MMULT_CTRL_ADDR_A_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_A_BASE + (offset + i)*4) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_A_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_A_HIGH - XHDCP22_MMULT_CTRL_ADDR_A_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_A_BASE + (offset + i)*4);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Write_A_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_A_HIGH - XHDCP22_MMULT_CTRL_ADDR_A_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_A_BASE + offset + i) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_A_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_A_HIGH - XHDCP22_MMULT_CTRL_ADDR_A_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_A_BASE + offset + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Get_B_BaseAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_B_BASE);
+}
+
+u32 XHdcp22_mmult_Get_B_HighAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_B_HIGH);
+}
+
+u32 XHdcp22_mmult_Get_B_TotalBytes(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (XHDCP22_MMULT_CTRL_ADDR_B_HIGH - XHDCP22_MMULT_CTRL_ADDR_B_BASE + 1);
+}
+
+u32 XHdcp22_mmult_Get_B_BitWidth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_WIDTH_B;
+}
+
+u32 XHdcp22_mmult_Get_B_Depth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_DEPTH_B;
+}
+
+u32 XHdcp22_mmult_Write_B_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_B_HIGH - XHDCP22_MMULT_CTRL_ADDR_B_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_B_BASE + (offset + i)*4) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_B_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_B_HIGH - XHDCP22_MMULT_CTRL_ADDR_B_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_B_BASE + (offset + i)*4);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Write_B_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_B_HIGH - XHDCP22_MMULT_CTRL_ADDR_B_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_B_BASE + offset + i) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_B_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_B_HIGH - XHDCP22_MMULT_CTRL_ADDR_B_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_B_BASE + offset + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Get_N_BaseAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_N_BASE);
+}
+
+u32 XHdcp22_mmult_Get_N_HighAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_N_HIGH);
+}
+
+u32 XHdcp22_mmult_Get_N_TotalBytes(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (XHDCP22_MMULT_CTRL_ADDR_N_HIGH - XHDCP22_MMULT_CTRL_ADDR_N_BASE + 1);
+}
+
+u32 XHdcp22_mmult_Get_N_BitWidth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_WIDTH_N;
+}
+
+u32 XHdcp22_mmult_Get_N_Depth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_DEPTH_N;
+}
+
+u32 XHdcp22_mmult_Write_N_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_N_HIGH - XHDCP22_MMULT_CTRL_ADDR_N_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_N_BASE + (offset + i)*4) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_N_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_N_HIGH - XHDCP22_MMULT_CTRL_ADDR_N_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_N_BASE + (offset + i)*4);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Write_N_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_N_HIGH - XHDCP22_MMULT_CTRL_ADDR_N_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_N_BASE + offset + i) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_N_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_N_HIGH - XHDCP22_MMULT_CTRL_ADDR_N_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_N_BASE + offset + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Get_NPrime_BaseAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE);
+}
+
+u32 XHdcp22_mmult_Get_NPrime_HighAddress(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH);
+}
+
+u32 XHdcp22_mmult_Get_NPrime_TotalBytes(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return (XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH - XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + 1);
+}
+
+u32 XHdcp22_mmult_Get_NPrime_BitWidth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_WIDTH_NPRIME;
+}
+
+u32 XHdcp22_mmult_Get_NPrime_Depth(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHDCP22_MMULT_CTRL_DEPTH_NPRIME;
+}
+
+u32 XHdcp22_mmult_Write_NPrime_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH - XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + (offset + i)*4) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_NPrime_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length)*4 > (XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH - XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u32 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + (offset + i)*4);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Write_NPrime_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH - XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + offset + i) = *(data + i);
+    }
+    return length;
+}
+
+u32 XHdcp22_mmult_Read_NPrime_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr -> IsReady == XIL_COMPONENT_IS_READY);
+
+    int i;
+
+    if ((offset + length) > (XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH - XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + 1))
+        return 0;
+
+    for (i = 0; i < length; i++) {
+        *(data + i) = *(u8 *)(InstancePtr->Config.BaseAddress + XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE + offset + i);
+    }
+    return length;
+}
+
+void XHdcp22_mmult_InterruptGlobalEnable(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_GIE, 1);
+}
+
+void XHdcp22_mmult_InterruptGlobalDisable(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_GIE, 0);
+}
+
+void XHdcp22_mmult_InterruptEnable(XHdcp22_mmult *InstancePtr, u32 Mask) {
+    u32 Register;
+
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    Register =  XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_IER);
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_IER, Register | Mask);
+}
+
+void XHdcp22_mmult_InterruptDisable(XHdcp22_mmult *InstancePtr, u32 Mask) {
+    u32 Register;
+
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    Register =  XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_IER);
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_IER, Register & (~Mask));
+}
+
+void XHdcp22_mmult_InterruptClear(XHdcp22_mmult *InstancePtr, u32 Mask) {
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    XHdcp22_mmult_WriteReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_ISR, Mask);
+}
+
+u32 XHdcp22_mmult_InterruptGetEnabled(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_IER);
+}
+
+u32 XHdcp22_mmult_InterruptGetStatus(XHdcp22_mmult *InstancePtr) {
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    return XHdcp22_mmult_ReadReg(InstancePtr->Config.BaseAddress, XHDCP22_MMULT_CTRL_ADDR_ISR);
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult.h
@@ -0,0 +1,179 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_mmult.h
+* @{
+* @details
+*
+* This is the main header file for the Xilinx HDCP 2.2 Montgomery Multipler
+* device driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  MH     12/07/15 Initial release.
+* 1.01  MH     08/04/16 Added 64 bit address support.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP22_MMULT_H
+#define XHDCP22_MMULT_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#if (defined(__KERNEL__) || (!defined(__linux__)))
+#include "xil_types.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xil_io.h"
+#else
+#include <stdint.h>
+#include <assert.h>
+#include <dirent.h>
+#include <fcntl.h>
+//#include <stdio.h>
+#include <stdlib.h>
+#include <linux/string.h>
+#include <sys/mman.h>
+#include <unistd.h>
+#include <stddef.h>
+#endif
+#include "xhdcp22_mmult_hw.h"
+
+/**************************** Type Definitions ******************************/
+#if (defined(__linux__) && (!defined(__KERNEL__)))
+typedef uint8_t u8;
+typedef uint16_t u16;
+typedef uint32_t u32;
+#else
+typedef struct {
+    u16 DeviceId;
+    UINTPTR BaseAddress;
+} XHdcp22_mmult_Config;
+#endif
+
+typedef struct {
+	XHdcp22_mmult_Config Config;
+    u32 IsReady;
+} XHdcp22_mmult;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+#if (defined(__KERNEL__) || (!defined(__linux__)))
+#define XHdcp22_mmult_WriteReg(BaseAddress, RegOffset, Data) \
+    Xil_Out32((BaseAddress) + (RegOffset), (u32)(Data))
+#define XHdcp22_mmult_ReadReg(BaseAddress, RegOffset) \
+    Xil_In32((BaseAddress) + (RegOffset))
+#else
+#define XHdcp22_mmult_WriteReg(BaseAddress, RegOffset, Data) \
+    *(volatile u32*)((BaseAddress) + (RegOffset)) = (u32)(Data)
+#define XHdcp22_mmult_ReadReg(BaseAddress, RegOffset) \
+    *(volatile u32*)((BaseAddress) + (RegOffset))
+
+#define Xil_AssertVoid(expr)    assert(expr)
+#define Xil_AssertNonvoid(expr) assert(expr)
+
+#define XST_SUCCESS             0
+#define XST_DEVICE_NOT_FOUND    2
+#define XST_OPEN_DEVICE_FAILED  3
+#define XIL_COMPONENT_IS_READY  1
+#endif
+
+/************************** Function Prototypes *****************************/
+#if (defined(__KERNEL__) || (!defined(__linux__)))
+int XHdcp22_mmult_Initialize(XHdcp22_mmult *InstancePtr, u16 DeviceId);
+XHdcp22_mmult_Config* XHdcp22_mmult_LookupConfig(u16 DeviceId);
+int XHdcp22_mmult_CfgInitialize(XHdcp22_mmult *InstancePtr, XHdcp22_mmult_Config *ConfigPtr, UINTPTR EffectiveAddr);
+#else
+int XHdcp22_mmult_Initialize(XHdcp22_mmult *InstancePtr, const char* InstanceName);
+int XHdcp22_mmult_Release(XHdcp22_mmult *InstancePtr);
+#endif
+
+void XHdcp22_mmult_Start(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_IsDone(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_IsIdle(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_IsReady(XHdcp22_mmult *InstancePtr);
+void XHdcp22_mmult_EnableAutoRestart(XHdcp22_mmult *InstancePtr);
+void XHdcp22_mmult_DisableAutoRestart(XHdcp22_mmult *InstancePtr);
+
+u32 XHdcp22_mmult_Get_U_BaseAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_U_HighAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_U_TotalBytes(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_U_BitWidth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_U_Depth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Write_U_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Read_U_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Write_U_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Read_U_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Get_A_BaseAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_A_HighAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_A_TotalBytes(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_A_BitWidth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_A_Depth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Write_A_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Read_A_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Write_A_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Read_A_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Get_B_BaseAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_B_HighAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_B_TotalBytes(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_B_BitWidth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_B_Depth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Write_B_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Read_B_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Write_B_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Read_B_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Get_N_BaseAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_N_HighAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_N_TotalBytes(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_N_BitWidth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_N_Depth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Write_N_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Read_N_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Write_N_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Read_N_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Get_NPrime_BaseAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_NPrime_HighAddress(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_NPrime_TotalBytes(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_NPrime_BitWidth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Get_NPrime_Depth(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_Write_NPrime_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Read_NPrime_Words(XHdcp22_mmult *InstancePtr, int offset, u32 *data, int length);
+u32 XHdcp22_mmult_Write_NPrime_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+u32 XHdcp22_mmult_Read_NPrime_Bytes(XHdcp22_mmult *InstancePtr, int offset, u8 *data, int length);
+
+void XHdcp22_mmult_InterruptGlobalEnable(XHdcp22_mmult *InstancePtr);
+void XHdcp22_mmult_InterruptGlobalDisable(XHdcp22_mmult *InstancePtr);
+void XHdcp22_mmult_InterruptEnable(XHdcp22_mmult *InstancePtr, u32 Mask);
+void XHdcp22_mmult_InterruptDisable(XHdcp22_mmult *InstancePtr, u32 Mask);
+void XHdcp22_mmult_InterruptClear(XHdcp22_mmult *InstancePtr, u32 Mask);
+u32 XHdcp22_mmult_InterruptGetEnabled(XHdcp22_mmult *InstancePtr);
+u32 XHdcp22_mmult_InterruptGetStatus(XHdcp22_mmult *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult_hw.h
@@ -0,0 +1,98 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_mmult_hw.h
+* @{
+* @details
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx HDCP22 Montgomery Multipler
+* (Mmult) core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  MH     12/07/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+// CTRL
+// 0x000 : Control signals
+//         bit 0  - ap_start (Read/Write/COH)
+//         bit 1  - ap_done (Read/COR)
+//         bit 2  - ap_idle (Read)
+//         bit 3  - ap_ready (Read)
+//         bit 7  - auto_restart (Read/Write)
+//         others - reserved
+// 0x004 : Global Interrupt Enable Register
+//         bit 0  - Global Interrupt Enable (Read/Write)
+//         others - reserved
+// 0x008 : IP Interrupt Enable Register (Read/Write)
+//         bit 0  - Channel 0 (ap_done)
+//         bit 1  - Channel 1 (ap_ready)
+//         others - reserved
+// 0x00c : IP Interrupt Status Register (Read/TOW)
+//         bit 0  - Channel 0 (ap_done)
+//         bit 1  - Channel 1 (ap_ready)
+//         others - reserved
+// 0x040 ~
+// 0x07f : Memory 'U' (16 * 32b)
+//         Word n : bit [31:0] - U[n]
+// 0x080 ~
+// 0x0bf : Memory 'A' (16 * 32b)
+//         Word n : bit [31:0] - A[n]
+// 0x0c0 ~
+// 0x0ff : Memory 'B' (16 * 32b)
+//         Word n : bit [31:0] - B[n]
+// 0x100 ~
+// 0x13f : Memory 'N' (16 * 32b)
+//         Word n : bit [31:0] - N[n]
+// 0x140 ~
+// 0x17f : Memory 'NPrime' (16 * 32b)
+//         Word n : bit [31:0] - NPrime[n]
+// (SC = Self Clear, COR = Clear on Read, TOW = Toggle on Write, COH = Clear on Handshake)
+
+#define XHDCP22_MMULT_CTRL_ADDR_AP_CTRL     0x000
+#define XHDCP22_MMULT_CTRL_ADDR_GIE         0x004
+#define XHDCP22_MMULT_CTRL_ADDR_IER         0x008
+#define XHDCP22_MMULT_CTRL_ADDR_ISR         0x00c
+#define XHDCP22_MMULT_CTRL_ADDR_U_BASE      0x040
+#define XHDCP22_MMULT_CTRL_ADDR_U_HIGH      0x07f
+#define XHDCP22_MMULT_CTRL_WIDTH_U          32
+#define XHDCP22_MMULT_CTRL_DEPTH_U          16
+#define XHDCP22_MMULT_CTRL_ADDR_A_BASE      0x080
+#define XHDCP22_MMULT_CTRL_ADDR_A_HIGH      0x0bf
+#define XHDCP22_MMULT_CTRL_WIDTH_A          32
+#define XHDCP22_MMULT_CTRL_DEPTH_A          16
+#define XHDCP22_MMULT_CTRL_ADDR_B_BASE      0x0c0
+#define XHDCP22_MMULT_CTRL_ADDR_B_HIGH      0x0ff
+#define XHDCP22_MMULT_CTRL_WIDTH_B          32
+#define XHDCP22_MMULT_CTRL_DEPTH_B          16
+#define XHDCP22_MMULT_CTRL_ADDR_N_BASE      0x100
+#define XHDCP22_MMULT_CTRL_ADDR_N_HIGH      0x13f
+#define XHDCP22_MMULT_CTRL_WIDTH_N          32
+#define XHDCP22_MMULT_CTRL_DEPTH_N          16
+#define XHDCP22_MMULT_CTRL_ADDR_NPRIME_BASE 0x140
+#define XHDCP22_MMULT_CTRL_ADDR_NPRIME_HIGH 0x17f
+#define XHDCP22_MMULT_CTRL_WIDTH_NPRIME     32
+#define XHDCP22_MMULT_CTRL_DEPTH_NPRIME     16
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_mmult_sinit.c
@@ -0,0 +1,79 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_mmult_sinit.c
+* @{
+* @details
+*
+* This file contains the static initialization file for the Xilinx
+* Montgomery Multiplier (Mmult) core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  MH     10/01/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+#if (defined(__KERNEL__) || (!defined(__linux__)))
+
+#include "xstatus.h"
+
+#include "xhdcp22_mmult.h"
+
+#ifndef XPAR_XHDCP22_MMULT_NUM_INSTANCES
+#define XPAR_XHDCP22_MMULT_NUM_INSTANCES 0
+#endif
+
+extern XHdcp22_mmult_Config XHdcp22_mmult_ConfigTable[];
+
+XHdcp22_mmult_Config *XHdcp22_mmult_LookupConfig(u16 DeviceId) {
+	XHdcp22_mmult_Config *ConfigPtr = NULL;
+
+	int Index;
+
+	for (Index = 0; Index < XPAR_XHDCP22_MMULT_NUM_INSTANCES; Index++) {
+		if (XHdcp22_mmult_ConfigTable[Index].DeviceId == DeviceId) {
+			ConfigPtr = &XHdcp22_mmult_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return ConfigPtr;
+}
+
+int XHdcp22_mmult_Initialize(XHdcp22_mmult *InstancePtr, u16 DeviceId) {
+	XHdcp22_mmult_Config *ConfigPtr;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	ConfigPtr = XHdcp22_mmult_LookupConfig(DeviceId);
+	if (ConfigPtr == NULL) {
+		InstancePtr->IsReady = 0;
+		return (XST_DEVICE_NOT_FOUND);
+	}
+
+	return XHdcp22_mmult_CfgInitialize(InstancePtr, ConfigPtr, ConfigPtr->BaseAddress);
+}
+
+#endif
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng.c
@@ -0,0 +1,151 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_rng.c
+* @{
+* @details
+*
+* This file contains the main implementation of the Xilinx HDCP 2.2 RNG
+* device driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* 1.01  MH     08/04/16 Added 64 bit address support.
+* 1.02  MH     02/17/16 Fixed pointer alignment problem in function
+*                       XHdcp22Rng_GetRandom
+* </pre>
+*
+******************************************************************************/
+
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_rng.h"
+#include <linux/string.h>
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function initializes the HDCP22 Rng core. This function must be called
+* prior to using the HDCP22 Rng core. Initialization of the HDCP22 Rng includes
+* setting up the instance data, and ensuring the hardware is in a quiescent
+* state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Rng core instance.
+* @param  CfgPtr points to the configuration structure associated with
+*         the HDCP22 Rng core core.
+* @param  EffectiveAddr is the base address of the device. If address
+*         translation is being used, then this parameter must reflect the
+*         virtual base address. Otherwise, the physical address should be
+*         used.
+*
+* @return
+*   - XST_SUCCESS if XHdcp22Rng_CfgInitialize was successful.
+*   - XST_FAILURE if HDCP22 Rng ID mismatched.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp22Rng_CfgInitialize(XHdcp22_Rng *InstancePtr,
+                                XHdcp22_Rng_Config *CfgPtr,
+                                UINTPTR EffectiveAddr)
+{
+	u32 RegValue;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+	Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+	/* Setup the instance */
+	(void)memset((void *)InstancePtr, 0, sizeof(XHdcp22_Rng));
+	(void)memcpy((void *)&(InstancePtr->Config), (const void *)CfgPtr, sizeof(XHdcp22_Rng_Config));
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+
+	/* Check ID */
+	RegValue = XHdcp22Rng_ReadReg(InstancePtr->Config.BaseAddress, (XHDCP22_RNG_VER_ID_OFFSET));
+	RegValue = ((RegValue) >> (XHDCP22_RNG_SHIFT_16)) & (XHDCP22_RNG_MASK_16);
+	if (RegValue != (XHDCP22_RNG_VER_ID)) {
+		return (XST_FAILURE);
+	}
+
+	/* Reset the hardware and set the flag to indicate the driver is ready */
+	InstancePtr->IsReady = (u32)(XIL_COMPONENT_IS_READY);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a random number.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Rng core instance.
+* @param  BufferPtr points to the buffer that will contain a random number.
+* @param  BufferLength is the length of the BufferPtr in bytes.
+*         The length must be greater than or equal to RandomLength.
+* @param  RandomLength is the requested length of the random number in bytes.
+*         The length must be a multiple of 4
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Rng_GetRandom(XHdcp22_Rng *InstancePtr, u8 *BufferPtr, u16 BufferLength, u16 RandomLength)
+{
+	u32 i, j;
+	u32 Offset = 0;
+	u32 RandomWord;
+	u8 *RandomPtr = (u8 *)&RandomWord;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(BufferPtr != NULL);
+	Xil_AssertVoid(RandomLength%4 == 0);
+	Xil_AssertVoid(BufferLength >= RandomLength);
+
+	for (i=0; i<RandomLength; i+=4)
+	{
+		RandomWord = XHdcp22Rng_ReadReg(InstancePtr->Config.BaseAddress,
+					XHDCP22_RNG_REG_RN_1_OFFSET + Offset);
+		for (j=0; j<4; j++) {
+			BufferPtr[i + j] = RandomPtr[j];
+		}
+
+		/* Increase offset to the next register and wrap after the last register
+		   (RNG length is 16 bytes) */
+		Offset = (Offset+4) % 16;
+	}
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng.h
@@ -0,0 +1,157 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_rng.h
+* @{
+* @details
+*
+* This is the main header file of the Xilinx HDCP 2.2 RNG device driver.
+* The RNG is a random number generator, which is used to produce
+* random numbers during the authentication and key exchange.
+*
+* <b>Software Initialization and Configuration</b>
+*
+* The application needs to do the following steps to run the RNG.
+* - Call XHdcp22Rng_LookupConfig using the device ID to find the
+*   core configuration instance.
+* - Call XHdcp22Rng_CfgInitialize to intitialize the device instance.
+* - Call XHdcp22Rng_Enable to enable the device.
+* - Call XHdcp22Rng_GetRandom to get random words.
+*
+* <b>Interrupts</b>
+*
+* None.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* 1.01  MH     08/04/16 Added 64 bit address support.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP22_RNG_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP22_RNG_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_rng_hw.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+/**
+* This typedef contains configuration information for the HDCP22 Rng core.
+* Each HDCP22 Rng device should have a configuration structure associated.
+*/
+typedef struct {
+	u16 DeviceId;     /**< DeviceId is the unique ID of the HDCP22 Rng core */
+	UINTPTR BaseAddress;  /**< BaseAddress is the physical base address of the core's registers */
+} XHdcp22_Rng_Config;
+
+/**
+* The XHdcp22 Rng driver instance data. An instance must be allocated for each
+* HDCP22 Rng core in use.
+*/
+typedef struct {
+	XHdcp22_Rng_Config Config; /**< Hardware Configuration */
+	u32 IsReady;               /**< Core and the driver instance are initialized */
+} XHdcp22_Rng;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDCP22 RNG peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 RNG core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Rng_Enable(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Rng_Enable(InstancePtr) \
+        XHdcp22Rng_WriteReg((InstancePtr)->Config.BaseAddress, \
+       (XHDCP22_RNG_REG_CTRL_SET_OFFSET), (XHDCP22_RNG_REG_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDCP22 RNG peripheral.
+*
+* @param  InstancePtr is a pointer to the HDCP22 RNG core instance.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Rng_Disable(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Rng_Disable(InstancePtr) \
+        XHdcp22Rng_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XHDCP22_RNG_REG_CTRL_CLR_OFFSET), (XHDCP22_RNG_REG_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the enabled state of HDCP22 RNG.
+* for the HDCP22 RNG peripheral.
+* @param  InstancePtr is a pointer to the HDCP22 RNG core instance.
+*
+* @return TRUE if HDCP22 RNG is enabled, FALSE otherwise.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Rng_IsEnabled(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Rng_IsEnabled(InstancePtr) \
+        ((XHdcp22Rng_GetControlReg((InstancePtr)->Config.BaseAddress)\
+        & XHDCP22_RNG_REG_CTRL_RUN_MASK) ==  XHDCP22_RNG_REG_CTRL_RUN_MASK)
+
+
+/************************** Function Prototypes ******************************/
+/* Initialization function in xhdcp22_rng_sinit.c */
+XHdcp22_Rng_Config *XHdcp22Rng_LookupConfig(u16 DeviceId);
+
+/* Initialization and control functions in xhdcp22_rng.c */
+int XHdcp22Rng_CfgInitialize(XHdcp22_Rng *InstancePtr, XHdcp22_Rng_Config *CfgPtr, UINTPTR EffectiveAddr);
+
+/* Return a random number */
+void XHdcp22Rng_GetRandom(XHdcp22_Rng *InstancePtr, u8 *BufferPtr, u16 BufferLength, u16 RandomLength);
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP22_RNG_H */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng_hw.h
@@ -0,0 +1,187 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_rng_hw.h
+* @{
+* @details
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx HDCP 2.2 RNG core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDCP22_RNG_HW_H
+/**< Prevent circular inclusions by using protection macros */
+#define XHDCP22_RNG_HW_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+/* HDCP22 RNG Version Interface base */
+#define XHDCP22_RNG_VER_BASE                (0*64)
+/** VER Identification register * register offset */
+#define XHDCP22_RNG_VER_ID_OFFSET           ((XHDCP22_RNG_VER_BASE)+(0*4))
+/** VER Version register * offset */
+#define XHDCP22_RNG_VER_VERSION_OFFSET      ((XHDCP22_RNG_VER_BASE)+(1*4))
+
+/* HDCP22 RNG Register peripheral interface base */
+#define XHDCP22_RNG_REG_BASE                (1*64)
+/** Control register * register offset */
+#define XHDCP22_RNG_REG_CTRL_OFFSET         ((XHDCP22_RNG_REG_BASE)+(0*4))
+/** Control set register * offset */
+#define XHDCP22_RNG_REG_CTRL_SET_OFFSET     ((XHDCP22_RNG_REG_BASE)+(1*4))
+/** Control clear register * offset */
+#define XHDCP22_RNG_REG_CTRL_CLR_OFFSET     ((XHDCP22_RNG_REG_BASE)+(2*4))
+/** Status register * offset */
+#define XHDCP22_RNG_REG_STA_OFFSET          ((XHDCP22_RNG_REG_BASE)+(3*4))
+/** Random number register 1 * offset */
+#define XHDCP22_RNG_REG_RN_1_OFFSET         ((XHDCP22_RNG_REG_BASE)+(4*4))
+/** Random number 2 * offset */
+#define XHDCP22_RNG_REG_RN_2_OFFSET         ((XHDCP22_RNG_REG_BASE)+(5*4))
+/** Random number 3 * offset */
+#define XHDCP22_RNG_REG_RN_3_OFFSET         ((XHDCP22_RNG_REG_BASE)+(6*4))
+/** Random number 4 * offset */
+#define XHDCP22_RNG_REG_RN_4_OFFSET         ((XHDCP22_RNG_REG_BASE)+(7*4))
+
+/* HDCP22 RNG Control register masks */
+/** Control register Run mask */
+#define XHDCP22_RNG_REG_CTRL_RUN_MASK       (1<<0)
+/** Control register Interrupt Enable mask. Reserved for future use. */
+#define XHDCP22_RNG_REG_CTRL_IE_MASK        (1<<1)
+
+/* HDCP22 RNG Status register masks */
+/** Status register interrupt mask. Reserved for future use.*/
+#define XHDCP22_RN_REG_STA_IRQ_MASK         (1<<0)
+/** Status register event mask. Reserved for future use.*/
+#define XHDCP22_RN_REG_STA_EVT_MASK         (1<<1)
+
+#define XHDCP22_RNG_SHIFT_16                16      /**< 16 shift value */
+#define XHDCP22_RNG_MASK_16                 0xFFFF  /**< 16 bit mask value */
+#define XHDCP22_RNG_VER_ID                  0x2200  /**< Version ID */
+
+
+/**************************** Type Definitions *******************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/** @name Register access macro definition
+* @{
+*/
+#define XHdcp22Rng_In32        Xil_In32        /**< Input Operations */
+#define XHdcp22Rng_Out32       Xil_Out32       /**< Output Operations */
+
+/*****************************************************************************/
+/**
+*
+* This macro reads a value from a HDCP22 RNG register.
+* A 32 bit read is performed.
+* If the component is implemented in a smaller width, only the least
+* significant data is read from the register. The most significant data
+* will be read as 0.
+*
+* @param  BaseAddress is the base address of the HDCP22 RNG core instance.
+* @param  RegOffset is the register offset of the register (defined at
+*         the top of this file).
+*
+* @return The 32-bit value of the register.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Rng_ReadReg(u32 BaseAddress, u32 RegOffset)
+*
+******************************************************************************/
+#define XHdcp22Rng_ReadReg(BaseAddress, RegOffset) \
+        XHdcp22Rng_In32((BaseAddress) + ((u32)RegOffset))
+
+/*****************************************************************************/
+/**
+*
+* This macro writes a value to a HDCP22 RNG register.
+* A 32 bit write is performed. If the component is implemented in a smaller
+* width, only the least significant data is written.
+*
+* @param  BaseAddress is the base address of the HDCP22 RNG core instance.
+* @param  RegOffset is the register offset of the register (defined at
+*         the top of this file) to be written.
+* @param  Data is the 32-bit value to write into the register.
+*
+* @return None.
+*
+* @note   C-style signature:
+*         void XHdcp22Rng_WriteReg(u32 BaseAddress, u32 RegOffset, u32 Data)
+*
+******************************************************************************/
+#define XHdcp22Rng_WriteReg(BaseAddress, RegOffset, Data) \
+        XHdcp22Rng_Out32((BaseAddress) + ((u32)RegOffset), (u32)(Data))
+
+/*****************************************************************************/
+/**
+*
+* This macro reads the status register from the HDCP22 RNG.
+*
+* @param  BaseAddress is the base address of the HDCP22 RNG core instance.
+*
+* @return A 32-bit value representing the contents of the status register.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Rng_GetStatusReg(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Rng_GetStatusReg(BaseAddress) \
+        XHdcp22Rng_ReadReg(BaseAddress, XHDCP22_RNG_REG_STA_OFFSET)
+
+/*****************************************************************************/
+/**
+*
+* This macro reads the control register from the HDCP22 RNG.
+*
+* @param  BaseAddress is the base address of the HDCP22 RNG core instance.
+*
+* @return A 32-bit value representing the contents of the control register.
+*
+* @note   C-style signature:
+*         u32 XHdcp22Rng_GetStatusReg(u32 BaseAddress)
+*
+******************************************************************************/
+#define XHdcp22Rng_GetControlReg(BaseAddress) \
+        XHdcp22Rng_ReadReg(BaseAddress, XHDCP22_RNG_REG_CTRL_OFFSET)
+/*@}*/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP2_RNG_HW_H */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rng_sinit.c
@@ -0,0 +1,96 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_rng_sinit.c
+* @{
+* @details
+*
+* This file contains the static initialization methods for the Xilinx HDCP
+* 2.2 RNG core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     10/01/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_rng.h"
+
+
+/************************** Constant Definitions *****************************/
+#ifndef XPAR_XHDCP22_RNG_NUM_INSTANCES
+#define XPAR_XHDCP22_RNG_NUM_INSTANCES 0
+#endif
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+extern XHdcp22_Rng_Config XHdcp22_Rng_ConfigTable[];
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XHdcp22_Rng_Config structure based
+* on the core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xhdcp22_rng_g.c file.
+*
+* @param  DeviceId is the unique core ID of the XHDCP22 Rng core for the
+*         lookup operation.
+*
+* @return XHdcp22Rng_LookupConfig returns a reference to a config record
+*         in the configuration table (in xhdcp22_rng_g.c) corresponding
+*         to <i>DeviceId</i>, or NULL if no match is found.
+*
+* @note   None.
+*
+******************************************************************************/
+
+/* Definitions for driver XHDCP22 RNG */
+XHdcp22_Rng_Config *XHdcp22Rng_LookupConfig(u16 DeviceId)
+{
+	XHdcp22_Rng_Config *CfgPtr = NULL;
+	u32 Index;
+
+	/* Checking for device id for which instance it is matching */
+	for (Index = (u32)0x0; Index < (u32)(XPAR_XHDCP22_RNG_NUM_INSTANCES);
+		Index++) {
+
+		/* Assigning address of config table if both device ids
+		 * are matched
+		 */
+		if (XHdcp22_Rng_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XHdcp22_Rng_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return (XHdcp22_Rng_Config *)CfgPtr;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx.c
@@ -0,0 +1,4312 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file xhdcp22_rx.c
+* @{
+* @details
+*
+* This file contains the main implementation of the Xilinx HDCP 2.2 Receiver
+* device driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+* 1.01  MH   01/15/16 Updated function XHdcp22Rx_SetDdcReauthReq to remove
+*                     static. Replaced function XHdcp22Rx_SetDdcHandles
+*                     with XHdcp22Rx_SetCallback. Added callback for
+*                     authenticated event.
+* 1.02  MH   03/02/16 Updated to perform Montgomery NPrime calcuation
+*                     when XHdcp22Rx_LoadPrivateKey is called.
+*                     Added function XHDCP22Rx_GetVersion.
+* 1.03  MH   03/15/16 Fixed XHdcp22Rx_SetLinkError and XHdcp22Rx_SetDdcError
+*                     functions to update error flag.
+* 2.00  MH   04/14/16 Updated for repeater upstream support.
+* 2.01  MH   02/28/17 Fixed compiler warnings.
+* 2.20  MH   06/08/17 Updated for 64 bit support.
+*</pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files ********************************/
+//#include "stdio.h"
+#include <linux/string.h>
+#include "xstatus.h"
+#include "xdebug.h"
+#include "xil_printf.h"
+
+#include "xhdcp22_rx_i.h"
+#include "xhdcp22_rx.h"
+#include "xtmrctr.h"
+
+/************************** Constant Definitions ****************************/
+
+/**************************** Type Definitions ******************************/
+
+/***************** Macros (Inline Functions) Definitions ********************/
+
+/************************** Variable Definitions ****************************/
+
+/************************** Function Prototypes *****************************/
+/* Functions for initializing subcores */
+static int  XHdcp22Rx_InitializeCipher(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_InitializeMmult(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_InitializeRng(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_InitializeTimer(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ComputeBaseAddress(UINTPTR BaseAddress, UINTPTR SubcoreOffset, UINTPTR *SubcoreAddressPtr);
+
+/* Functions for generating authentication parameters */
+static int  XHdcp22Rx_GenerateRrx(XHdcp22_Rx *InstancePtr, u8 *RrxPtr);
+
+/* Functions for performing various tasks during authentication */
+static u8   XHdcp22Rx_IsWriteMessageAvailable(XHdcp22_Rx *InstancePtr);
+static u8   XHdcp22Rx_IsReadMessageComplete(XHdcp22_Rx *InstancePtr);
+static void XHdcp22Rx_SetRxStatus(XHdcp22_Rx *InstancePtr, u16 MessageSize,
+              u8 ReauthReq, u8 TopologyReady);
+static void	XHdcp22Rx_SetDdcReauthReq(XHdcp22_Rx *InstancePtr);
+static void XHdcp22Rx_ResetDdc(XHdcp22_Rx *InstancePtr, u8 ClrWrBuffer,
+              u8 ClrRdBuffer, u8 ClrReady, u8 ClrReauthReq);
+static void XHdcp22Rx_ResetAfterError(XHdcp22_Rx *InstancePtr);
+static void XHdcp22Rx_ResetParams(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_PollMessage(XHdcp22_Rx *InstancePtr);
+static void XHdcp22Rx_TimerHandler(void *CallbackRef, u8 TmrCntNumber);
+static void XHdcp22Rx_StartTimer(XHdcp22_Rx *InstancePtr, u32 TimeOut_mSec,
+              u8 ReasonId);
+static void XHdcp22Rx_StopTimer(XHdcp22_Rx *InstancePtr);
+
+/* Functions for implementing the receiver state machine */
+static void *XHdcp22Rx_StateB0(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateB1(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateB2(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateB3(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateB4(XHdcp22_Rx *InstancePtr);
+
+/* Functions for implementing the repeater upstream state machine.
+   Repeater states C0-C3 are identical to receiver states B0-B3. */
+static void *XHdcp22Rx_StateC4(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateC5(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateC6(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateC7(XHdcp22_Rx *InstancePtr);
+static void *XHdcp22Rx_StateC8(XHdcp22_Rx *InstancePtr);
+
+/* Functions for processing received messages */
+static int  XHdcp22Rx_ProcessMessageAKEInit(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ProcessMessageAKENoStoredKm(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ProcessMessageAKEStoredKm(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ProcessMessageLCInit(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ProcessMessageSKESendEks(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ProcessMessageRepeaterAuthSendAck(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_ProcessMessageRepeaterAuthStreamManage(XHdcp22_Rx *InstancePtr);
+
+/* Functions for generating and sending messages */
+static int  XHdcp22Rx_SendMessageAKESendCert(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_SendMessageAKESendHPrime(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_SendMessageAKESendPairingInfo(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_SendMessageLCSendLPrime(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_SendMessageRepeaterAuthSendRxIdList(XHdcp22_Rx *InstancePtr);
+static int  XHdcp22Rx_SendMessageRepeaterAuthStreamReady(XHdcp22_Rx *InstancePtr);
+
+/* Function for setting fields inside the topology structure */
+static void XHdcp22Rx_SetTopologyDepth(XHdcp22_Rx *InstancePtr, u8 Depth);
+static void XHdcp22Rx_SetTopologyDeviceCnt(XHdcp22_Rx *InstancePtr, u8 DeviceCnt);
+static void XHdcp22Rx_SetTopologyMaxDevsExceeded(XHdcp22_Rx *InstancePtr, u8 Value);
+static void XHdcp22Rx_SetTopologyMaxCascadeExceeded(XHdcp22_Rx *InstancePtr, u8 Value);
+static void XHdcp22Rx_SetTopologyHdcp2LegacyDeviceDownstream(XHdcp22_Rx *InstancePtr, u8 Value);
+static void XHdcp22Rx_SetTopologyHdcp1DeviceDownstream(XHdcp22_Rx *InstancePtr, u8 Value);
+
+/* Functions for stub callbacks */
+static void XHdcp22_Rx_StubRunHandler(void *HandlerRef);
+static void XHdcp22_Rx_StubSetHandler(void *HandlerRef, u32 Data);
+static u32  XHdcp22_Rx_StubGetHandler(void *HandlerRef);
+
+/****************************************************************************/
+/**
+* Initialize the instance provided by the caller based on the given
+* configuration data.
+*
+* @param 	InstancePtr is a pointer to an XHdcp22_Rx instance.
+*			The memory the pointer references must be pre-allocated by
+*			the caller. Further calls to manipulate the driver through
+*			the HDCP22-RX API must be made with this pointer.
+* @param	Config is a reference to a structure containing information
+*			about a specific HDCP22-RX device. This function
+*			initializes an InstancePtr object for a specific device
+*			specified by the contents of Config. This function can
+*			initialize multiple instance objects with the use of multiple
+*			calls giving different Config information on each call.
+* @param	EffectiveAddr is the base address of the device. If address
+*			translation is being used, then this parameter must reflect the
+*			virtual base address. Otherwise, the physical address should be
+*			used.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+int XHdcp22Rx_CfgInitialize(XHdcp22_Rx *InstancePtr, XHdcp22_Rx_Config *ConfigPtr,
+      UINTPTR EffectiveAddr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(ConfigPtr != NULL);
+	Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+	int Status;
+
+	/* Clear the instance */
+	memset((void *)InstancePtr, 0, sizeof(XHdcp22_Rx));
+
+	/* Copy configuration settings */
+	memcpy((void *)&(InstancePtr->Config), (const void *)ConfigPtr, sizeof(XHdcp22_Rx_Config));
+
+	/* Set default values */
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+	InstancePtr->StateFunc = (XHdcp22_Rx_StateFunc)(&XHdcp22Rx_StateB0);
+	InstancePtr->Info.IsEnabled = FALSE;
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_UNAUTHENTICATED;
+	InstancePtr->Info.IsNoStoredKm = FALSE;
+	InstancePtr->Info.ReauthReq = FALSE;
+	InstancePtr->Info.TopologyReady = FALSE;
+	InstancePtr->Info.IsEncrypted = FALSE;
+	InstancePtr->Info.LCInitAttempts = 0;
+	InstancePtr->Info.AuthRequestCnt = 0;
+	InstancePtr->Info.ReauthRequestCnt = 0;
+	InstancePtr->Info.LinkErrorCnt = 0;
+	InstancePtr->Info.DdcErrorCnt = 0;
+	InstancePtr->Info.ErrorFlag = XHDCP22_RX_ERROR_FLAG_NONE;
+	InstancePtr->Info.ErrorFlagSticky = XHDCP22_RX_ERROR_FLAG_NONE;
+	InstancePtr->Info.CurrentState = XHDCP22_RX_STATE_B0_WAIT_AKEINIT;
+	InstancePtr->Info.NextState = XHDCP22_RX_STATE_B0_WAIT_AKEINIT;
+
+	/* Set default repeater values */
+	InstancePtr->Info.IsTopologyValid = FALSE;
+	InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+	InstancePtr->Info.SeqNumV = 0;
+	InstancePtr->Info.HasStreamManagementInfo = FALSE;
+	InstancePtr->Info.SkipRead = FALSE;
+
+	/* Set the callback functions to stubs */
+	InstancePtr->Handles.DdcSetAddressCallback = XHdcp22_Rx_StubSetHandler;
+	InstancePtr->Handles.IsDdcSetAddressCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcSetDataCallback = XHdcp22_Rx_StubSetHandler;
+	InstancePtr->Handles.IsDdcSetDataCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcGetDataCallback = XHdcp22_Rx_StubGetHandler;
+	InstancePtr->Handles.IsDdcGetDataCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcGetWriteBufferSizeCallback = XHdcp22_Rx_StubGetHandler;
+	InstancePtr->Handles.IsDdcGetWriteBufferSizeCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcGetReadBufferSizeCallback = XHdcp22_Rx_StubGetHandler;
+	InstancePtr->Handles.IsDdcGetReadBufferSizeCallbackRefSet = (FALSE);
+
+	InstancePtr->Handles.DdcIsWriteBufferEmptyCallback = XHdcp22_Rx_StubGetHandler;
+	InstancePtr->Handles.IsDdcIsWriteBufferEmptyCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcIsReadBufferEmptyCallback = XHdcp22_Rx_StubGetHandler;
+	InstancePtr->Handles.IsDdcIsReadBufferEmptyCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcClearReadBufferCallback = XHdcp22_Rx_StubRunHandler;
+	InstancePtr->Handles.IsDdcClearReadBufferCallbackSet = (FALSE);
+
+	InstancePtr->Handles.DdcClearWriteBufferCallback = XHdcp22_Rx_StubRunHandler;
+	InstancePtr->Handles.IsDdcClearWriteBufferCallbackSet = (FALSE);
+
+	InstancePtr->Handles.AuthenticatedCallback = XHdcp22_Rx_StubRunHandler;
+	InstancePtr->Handles.IsAuthenticatedCallbackSet = (FALSE);
+
+	InstancePtr->Handles.AuthenticationRequestCallback = XHdcp22_Rx_StubRunHandler;
+	InstancePtr->Handles.IsAuthenticationRequestCallbackSet = (FALSE);
+
+	InstancePtr->Handles.StreamManageRequestCallback = XHdcp22_Rx_StubRunHandler;
+	InstancePtr->Handles.IsStreamManageRequestCallbackSet = (FALSE);
+
+	InstancePtr->Handles.TopologyUpdateCallback = XHdcp22_Rx_StubRunHandler;
+	InstancePtr->Handles.IsTopologyUpdateCallbackSet = (FALSE);
+
+	InstancePtr->Handles.IsDdcAllCallbacksSet = (FALSE);
+
+	/* Set RXCAPS repeater mode */
+	InstancePtr->RxCaps[0] = 0x02;
+	InstancePtr->RxCaps[1] = 0x00;
+	InstancePtr->RxCaps[2] = (InstancePtr->Config.Mode == XHDCP22_RX_RECEIVER) ? 0x00 : 0x01;
+
+	/* Reset stored parameters */
+	XHdcp22Rx_ResetParams(InstancePtr);
+
+	/* Configure Cipher Instance */
+	Status = XHdcp22Rx_InitializeCipher(InstancePtr);
+	if(Status == XST_FAILURE)
+	{
+		return Status;
+	}
+
+	/* Configure Mmult Instance */
+	Status = XHdcp22Rx_InitializeMmult(InstancePtr);
+	if(Status == XST_FAILURE)
+	{
+		return Status;
+	}
+
+	/* Configure Rng Instance */
+	Status = XHdcp22Rx_InitializeRng(InstancePtr);
+	if(Status == XST_FAILURE)
+	{
+		return Status;
+	}
+
+	/* Configure Timer Instance */
+	Status = XHdcp22Rx_InitializeTimer(InstancePtr);
+	if(Status == XST_FAILURE)
+	{
+		return Status;
+	}
+
+	/* Reset log */
+	XHdcp22Rx_LogReset(InstancePtr, FALSE);
+
+	/* Indicate component has been initialized */
+	InstancePtr->IsReady = (XIL_COMPONENT_IS_READY);
+	/* Default enable broadcasting */
+	InstancePtr->Hdcp22Broadcast = TRUE;
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function resets the HDCP22-RX system to the default state.
+* The HDCP22-RX DDC registers are set to their default value
+* and the message buffer is reset.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		The DDC message handles must be assigned by the
+* 			XHdcp22Rx_SetDdcHandles function prior to calling
+* 			this reset function.
+******************************************************************************/
+int XHdcp22Rx_Reset(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	/* Verify DDC handles assigned */
+	Xil_AssertNonvoid(InstancePtr->Handles.IsDdcAllCallbacksSet == TRUE);
+
+	int AuthenticationStatus = InstancePtr->Info.AuthenticationStatus;
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO, XHDCP22_RX_LOG_INFO_RESET);
+
+	/* Clear message buffer */
+	memset(&InstancePtr->MessageBuffer, 0, sizeof(XHdcp22_Rx_Message));
+	InstancePtr->MessageSize = 0;
+
+	/* Set default values */
+	InstancePtr->StateFunc = (XHdcp22_Rx_StateFunc)(&XHdcp22Rx_StateB0);
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_UNAUTHENTICATED;
+	InstancePtr->Info.IsNoStoredKm = FALSE;
+	InstancePtr->Info.ReauthReq = FALSE;
+	InstancePtr->Info.TopologyReady = FALSE;
+	InstancePtr->Info.IsEncrypted = FALSE;
+	InstancePtr->Info.LCInitAttempts = 0;
+	InstancePtr->Info.AuthRequestCnt = 0;
+	InstancePtr->Info.ReauthRequestCnt = 0;
+	InstancePtr->Info.LinkErrorCnt = 0;
+	InstancePtr->Info.DdcErrorCnt = 0;
+	InstancePtr->Info.ErrorFlag = XHDCP22_RX_ERROR_FLAG_NONE;
+	InstancePtr->Info.ErrorFlagSticky = XHDCP22_RX_ERROR_FLAG_NONE;
+	InstancePtr->Info.CurrentState = XHDCP22_RX_STATE_B0_WAIT_AKEINIT;
+	InstancePtr->Info.NextState = XHDCP22_RX_STATE_B0_WAIT_AKEINIT;
+
+	/* Reset repeater values */
+	memset(&InstancePtr->Topology, 0, sizeof(XHdcp22_Rx_Topology));
+	InstancePtr->Info.IsTopologyValid = FALSE;
+	InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+	InstancePtr->Info.SeqNumV = 0;
+	InstancePtr->Info.HasStreamManagementInfo = FALSE;
+	InstancePtr->Info.SkipRead = FALSE;
+
+	/* Reset stored parameters */
+	XHdcp22Rx_ResetParams(InstancePtr);
+
+	/* Reset DDC registers */
+	XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+
+	/* Disable timer */
+	XHdcp22Rx_StopTimer(InstancePtr);
+
+	/* Disable cipher */
+	XHdcp22Cipher_Disable(&InstancePtr->CipherInst);
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_UNAUTHENTICATED */
+	if((InstancePtr->Handles.IsUnauthenticatedCallbackSet) &&
+		 (AuthenticationStatus == XHDCP22_RX_AUTHENTICATED))
+	{
+		InstancePtr->Handles.UnauthenticatedCallback(InstancePtr->Handles.UnauthenticatedCallbackRef);
+	}
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function enables the HDCP22-RX state machine. The HDCP2Version
+* register is set to active.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		Before enabling the state machine ensure that the instance has
+*			been initialized, DDC message handles have been assigned, and keys
+*			have been loaded.
+******************************************************************************/
+int XHdcp22Rx_Enable(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	/* Verify DDC handles assigned */
+	Xil_AssertNonvoid(InstancePtr->Handles.IsDdcAllCallbacksSet == TRUE);
+	/* Verify keys loaded */
+	Xil_AssertNonvoid(InstancePtr->PublicCertPtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->PrivateKeyPtr != NULL);
+	/* Verify devices ready */
+	Xil_AssertNonvoid(InstancePtr->MmultInst.IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertNonvoid(InstancePtr->TimerInst.IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertNonvoid(InstancePtr->RngInst.IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertNonvoid(InstancePtr->CipherInst.IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO, XHDCP22_RX_LOG_INFO_ENABLE);
+
+	/* Enable RNG and Cipher */
+	XHdcp22Rng_Enable(&InstancePtr->RngInst);
+	XHdcp22Cipher_Enable(&InstancePtr->CipherInst);
+
+	/* Assert enabled flag */
+	InstancePtr->Info.IsEnabled = TRUE;
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function disables the HDCP22-RX state machine. The HDCP2Version
+* register is cleared, and the ReauthReq bit is set in the
+* RxStatus register to allow the transmitter to recover when it has
+* already authenticated. Without setting the ReauthReq bit the
+* transmitter will not know that HDCP 2.2 protocol has been disabled
+* by the Receiver after it has already authenticated.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		The HDCP22-RX cipher is disabled.
+******************************************************************************/
+int XHdcp22Rx_Disable(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO, XHDCP22_RX_LOG_INFO_DISABLE);
+
+	/* Set ReauthReq for recovery when already authenticated */
+	XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+
+	/* Disable, Rng, Cipher, and Timer */
+	XHdcp22Rng_Disable(&InstancePtr->RngInst);
+	XHdcp22Cipher_Disable(&InstancePtr->CipherInst);
+	XHdcp22Rx_StopTimer(InstancePtr);
+
+	/* Deassert device enable flag */
+	InstancePtr->Info.IsEnabled = FALSE;
+
+	return (XST_SUCCESS);
+}
+
+void XHdcp22Rx_SetBroadcast(XHdcp22_Rx *InstancePtr, u8 enable)
+{
+	InstancePtr->Hdcp22Broadcast = enable;
+	if(enable == TRUE) {
+		/* Set HDCP2Version register */
+		InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef, XHDCP22_RX_DDC_VERSION_REG);
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef, 0x4);
+	} else {
+		/* Disable HDCP2Version register */
+		InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef, XHDCP22_RX_DDC_VERSION_REG);
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef, 0x0);
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs callback functions for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                                           Callback Function Type
+* -------------------------                             ---------------------------
+* (XHDCP22_RX_HANDLER_DDC_SETREGADDR)                   DdcSetAddressCallback
+* (XHDCP22_RX_HANDLER_DDC_SETREGDATA)                   DdcSetDataCallback
+* (XHDCP22_RX_HANDLER_DDC_GETREGDATA)                   DdcGetDataCallback
+* (XHDCP22_RX_HANDLER_DDC_GETWBUFSIZE)                  DdcGetWriteBufferSizeCallback
+* (XHDCP22_RX_HANDLER_DDC_GETRBUFSIZE)                  DdcGetReadBufferSizeCallback
+* (XHDCP22_RX_HANDLER_DDC_ISWBUFEMPTY)                  DdcIsWriteBufferEmptyCallback
+* (XHDCP22_RX_HANDLER_DDC_ISRBUFEMPTY)                  DdcIsReadBufferEmptyCallback
+* (XHDCP22_RX_HANDLER_DDC_CLEARRBUF)                    DdcClearReadBufferCallback
+* (XHDCP22_RX_HANDLER_DDC_CLEARWBUF)                    DdcClearWriteBufferCallback
+* (XHDCP22_RX_HANDLER_AUTHENTICATED)                    AuthenticatedCallback
+* (XHDCP22_RX_HANDLER_UNAUTHENTICATED)                  UnauthenticatedCallback
+* (XHDCP22_RX_HANDLER_AUTHENTICATION_REQUEST)           AuthenticationRequestCallback
+* (XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST)            StreamManageRequestCallback
+* (XHDCP22_RX_HANDLER_TOPOLOGY_UPDATE)                  TopologyUpdateCallback
+* </pre>
+*
+* @param	InstancePtr is a pointer to the HDMI RX core instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*			callback function when it is invoked.
+*
+* @return
+*			- XST_SUCCESS if callback function installed successfully.
+*			- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*			installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp22Rx_SetCallback(XHdcp22_Rx *InstancePtr, XHdcp22_Rx_HandlerType HandlerType, void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType > (XHDCP22_RX_HANDLER_UNDEFINED));
+	Xil_AssertNonvoid(HandlerType < (XHDCP22_RX_HANDLER_INVALID));
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	u32 Status;
+
+	/* Check for handler type */
+	switch(HandlerType)
+	{
+		// DDC Set Register Address
+		case (XHDCP22_RX_HANDLER_DDC_SETREGADDR):
+			InstancePtr->Handles.DdcSetAddressCallback = (XHdcp22_Rx_SetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcSetAddressCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcSetAddressCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Set Register Data
+		case (XHDCP22_RX_HANDLER_DDC_SETREGDATA):
+			InstancePtr->Handles.DdcSetDataCallback = (XHdcp22_Rx_SetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcSetDataCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcSetDataCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Get Register Data
+		case (XHDCP22_RX_HANDLER_DDC_GETREGDATA):
+			InstancePtr->Handles.DdcGetDataCallback = (XHdcp22_Rx_GetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcGetDataCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcGetDataCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Get Write Buffer Size
+		case (XHDCP22_RX_HANDLER_DDC_GETWBUFSIZE):
+			InstancePtr->Handles.DdcGetWriteBufferSizeCallback = (XHdcp22_Rx_GetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcGetWriteBufferSizeCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcGetWriteBufferSizeCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Get Read Buffer Size
+		case (XHDCP22_RX_HANDLER_DDC_GETRBUFSIZE):
+			InstancePtr->Handles.DdcGetReadBufferSizeCallback = (XHdcp22_Rx_GetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcGetReadBufferSizeCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcGetReadBufferSizeCallbackRefSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Is Write Buffer Empty
+		case (XHDCP22_RX_HANDLER_DDC_ISWBUFEMPTY):
+			InstancePtr->Handles.DdcIsWriteBufferEmptyCallback = (XHdcp22_Rx_GetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcIsWriteBufferEmptyCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcIsWriteBufferEmptyCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Is Read Buffer Empty
+		case (XHDCP22_RX_HANDLER_DDC_ISRBUFEMPTY):
+			InstancePtr->Handles.DdcIsReadBufferEmptyCallback = (XHdcp22_Rx_GetHandler)CallbackFunc;
+			InstancePtr->Handles.DdcIsReadBufferEmptyCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcIsReadBufferEmptyCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Clear Read Buffer
+		case (XHDCP22_RX_HANDLER_DDC_CLEARRBUF):
+			InstancePtr->Handles.DdcClearReadBufferCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.DdcClearReadBufferCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcClearReadBufferCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC Clear Write Buffer
+		case (XHDCP22_RX_HANDLER_DDC_CLEARWBUF):
+			InstancePtr->Handles.DdcClearWriteBufferCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.DdcClearWriteBufferCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsDdcClearWriteBufferCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Authenticated
+		case (XHDCP22_RX_HANDLER_AUTHENTICATED):
+			InstancePtr->Handles.AuthenticatedCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.AuthenticatedCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsAuthenticatedCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Unauthenticated
+		case (XHDCP22_RX_HANDLER_UNAUTHENTICATED):
+			InstancePtr->Handles.UnauthenticatedCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.UnauthenticatedCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsUnauthenticatedCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Authentication Request
+		case (XHDCP22_RX_HANDLER_AUTHENTICATION_REQUEST):
+			InstancePtr->Handles.AuthenticationRequestCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.AuthenticationRequestCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsAuthenticationRequestCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Management Request
+		case (XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST):
+			InstancePtr->Handles.StreamManageRequestCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.StreamManageRequestCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsStreamManageRequestCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Topology Update
+		case (XHDCP22_RX_HANDLER_TOPOLOGY_UPDATE):
+			InstancePtr->Handles.TopologyUpdateCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.TopologyUpdateCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsTopologyUpdateCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Encryption Status Update
+		case (XHDCP22_RX_HANDLER_ENCRYPTION_UPDATE):
+			InstancePtr->Handles.EncryptionStatusCallback = (XHdcp22_Rx_RunHandler)CallbackFunc;
+			InstancePtr->Handles.EncryptionStatusCallbackRef = CallbackRef;
+			InstancePtr->Handles.IsEncryptionStatusCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		default:
+			Status = (XST_INVALID_PARAM);
+			break;
+	}
+
+	/* Reset DDC registers only when all handlers have been registered */
+    if(InstancePtr->Handles.IsDdcSetAddressCallbackSet &&
+		InstancePtr->Handles.IsDdcSetDataCallbackSet &&
+		InstancePtr->Handles.IsDdcGetDataCallbackSet &&
+		InstancePtr->Handles.IsDdcGetWriteBufferSizeCallbackSet &&
+		InstancePtr->Handles.IsDdcGetReadBufferSizeCallbackRefSet &&
+		InstancePtr->Handles.IsDdcIsWriteBufferEmptyCallbackSet &&
+		InstancePtr->Handles.IsDdcIsReadBufferEmptyCallbackSet &&
+		InstancePtr->Handles.IsDdcClearReadBufferCallbackSet &&
+		InstancePtr->Handles.IsDdcClearWriteBufferCallbackSet &&
+        InstancePtr->Handles.IsDdcAllCallbacksSet == (FALSE))
+	{
+		InstancePtr->Handles.IsDdcAllCallbacksSet = (TRUE);
+		XHdcp22Rx_ResetDdc(InstancePtr, TRUE, TRUE, TRUE, TRUE);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function executes the HDCP22-RX state machine.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		State transitions are logged.
+******************************************************************************/
+int XHdcp22Rx_Poll(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Run state machine */
+	if(InstancePtr->Info.IsEnabled == TRUE)
+	{
+		InstancePtr->StateFunc = (XHdcp22_Rx_StateFunc)(*InstancePtr->StateFunc)(InstancePtr);
+	}
+
+	/* Log state transitions */
+	if(InstancePtr->Info.NextState != InstancePtr->Info.CurrentState)
+	{
+	    XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_STATE, InstancePtr->Info.NextState);
+	}
+
+	return (int)(InstancePtr->Info.AuthenticationStatus);
+}
+
+/*****************************************************************************/
+/**
+* This function checks if the HDCP22-RX state machine is enabled.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+u8 XHdcp22Rx_IsEnabled(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return InstancePtr->Info.IsEnabled;
+}
+
+/*****************************************************************************/
+/**
+* This function checks if the HDCP22-RX cipher encryption is enabled.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+u8 XHdcp22Rx_IsEncryptionEnabled(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 Status;
+
+	Status = XHdcp22Cipher_IsEncrypted(&InstancePtr->CipherInst);
+
+	return (Status) ? TRUE : FALSE;
+}
+
+/*****************************************************************************/
+/**
+* This function checks if the HDCP22-RX state machine is enabled but
+* not yet in the Authenticated state.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+u8 XHdcp22Rx_IsInProgress(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Info.AuthenticationStatus == XHDCP22_RX_AUTHENTICATION_BUSY) ? (TRUE) : (FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function checks if the HDCP22-RX state machine is in the
+* Authenticated state.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+u8 XHdcp22Rx_IsAuthenticated(XHdcp22_Rx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Info.AuthenticationStatus == XHDCP22_RX_AUTHENTICATED) ? (TRUE) : (FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function checks if the HDCP22-RX state machine has detected an error
+* condition.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+u8 XHdcp22Rx_IsError(XHdcp22_Rx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Info.ErrorFlagSticky != XHDCP22_RX_ERROR_FLAG_NONE) ? (TRUE) : (FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current repeater mode status.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return
+*   - TRUE if the HDCP 2.2 instance is the upstream port of a repeater
+*   - FALSE if the HDCP 2.2 instance is a receiver
+*
+******************************************************************************/
+u8 XHdcp22Rx_IsRepeater(XHdcp22_Rx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Config.Mode != XHDCP22_RX_RECEIVER) ? (TRUE) : (FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the repeater mode status.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param  Set is TRUE to enable repeater mode and FALSE to disable.
+*
+* @return None.
+*
+******************************************************************************/
+void XHdcp22Rx_SetRepeater(XHdcp22_Rx *InstancePtr, u8 Set)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Update mode */
+	if (Set)
+		InstancePtr->Config.Mode = XHDCP22_RX_REPEATER;
+	else
+		InstancePtr->Config.Mode = XHDCP22_RX_RECEIVER;
+
+	/* Set RxCaps */
+	InstancePtr->RxCaps[0] = 0x02;
+	InstancePtr->RxCaps[1] = 0x00;
+	InstancePtr->RxCaps[2] = (InstancePtr->Config.Mode == XHDCP22_RX_RECEIVER) ? 0x00 : 0x01;
+}
+
+/*****************************************************************************/
+/**
+* This function is called when 50 consecutive data island ECC errors are
+* detected indicating a link integrity problem. The error flag is set
+* indicating to the state machine that REAUTH_REQ bit in the RXSTATUS
+* register be set. Setting this flag only takes effect when the
+* authentication state machine is in the Authenticated state B4.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		This function can be registered as an asynchronous callback.
+******************************************************************************/
+void XHdcp22Rx_SetLinkError(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Increment link error count */
+	InstancePtr->Info.LinkErrorCnt++;
+
+	/* Set Error Flag */
+	InstancePtr->Info.ErrorFlag |= XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY;
+
+	/* Log error event set flag */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY);
+}
+
+/*****************************************************************************/
+/**
+* This function is called when a DDC read/write burst stops prior to completing
+* the expected message size. This will cause the message buffers to be flushed
+* and state machine reset.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		This function can be registered as an asynchronous callback.
+******************************************************************************/
+void XHdcp22Rx_SetDdcError(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Increment link error count */
+	InstancePtr->Info.DdcErrorCnt++;
+
+	/* Set Error Flag */
+	InstancePtr->Info.ErrorFlag |= XHDCP22_RX_ERROR_FLAG_DDC_BURST;
+
+	/* Log error event and set flag */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_DDC_BURST);
+}
+
+/*****************************************************************************/
+/**
+* This function is called when a complete message is available in the
+* write message buffer.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		This function can be registered as an asynchronous callback.
+******************************************************************************/
+void XHdcp22Rx_SetWriteMessageAvailable(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_WRITE_MESSAGE_AVAILABLE);
+
+	/* Update DDC flag */
+	InstancePtr->Info.DdcFlag |= XHDCP22_RX_DDC_FLAG_WRITE_MESSAGE_READY;
+}
+
+/*****************************************************************************/
+/**
+* This function is called when a message has been read out of the read
+* message buffer.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		This function can be registered as an asynchronous callback.
+******************************************************************************/
+void XHdcp22Rx_SetReadMessageComplete(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_READ_MESSAGE_COMPLETE);
+
+	/* Update DDC flag */
+	InstancePtr->Info.DdcFlag |= XHDCP22_RX_DDC_FLAG_READ_MESSAGE_READY;
+}
+
+/*****************************************************************************/
+/**
+* This function is used to load the Lc128 value by copying the contents
+* of the array referenced by Lc128Ptr into the cipher.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	Lc128Ptr is a pointer to an array.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_LoadLc128(XHdcp22_Rx *InstancePtr, const u8 *Lc128Ptr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Lc128Ptr != NULL);
+
+	XHdcp22Cipher_SetLc128(&InstancePtr->CipherInst, Lc128Ptr,  XHDCP22_RX_LC128_SIZE);
+}
+
+/*****************************************************************************/
+/**
+* This function is used to load the public certificate.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	PublicCertPtr is a pointer to an array.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_LoadPublicCert(XHdcp22_Rx *InstancePtr, const u8 *PublicCertPtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(PublicCertPtr != NULL);
+
+	InstancePtr->PublicCertPtr = PublicCertPtr;
+}
+
+/*****************************************************************************/
+/**
+* This function is used to load the private key.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	PrivateKeyPtr is a pointer to an array.
+*
+* @return	- XST_SUCCESS if MMULT keys are calcualted correctly.
+* 			- XST_FAILURE if MMULT keys are not calculated correctly.
+*
+* @note		None.
+******************************************************************************/
+int XHdcp22Rx_LoadPrivateKey(XHdcp22_Rx *InstancePtr, const u8 *PrivateKeyPtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(PrivateKeyPtr != NULL);
+
+	int Status = XST_SUCCESS;
+	XHdcp22_Rx_KprivRx *PrivateKey = (XHdcp22_Rx_KprivRx *)PrivateKeyPtr;
+
+	/* Load the Private Key */
+	InstancePtr->PrivateKeyPtr = PrivateKeyPtr;
+
+	/* Calculate Montgomery Multiplier NPrimeP */
+	Status = XHdcp22Rx_CalcMontNPrime(InstancePtr->NPrimeP, (u8 *)PrivateKey->p, XHDCP22_RX_P_SIZE/4);
+    if(Status != XST_SUCCESS)
+	{
+	    xil_printf("ERROR: HDCP22-RX MMult NPrimeP Generation Failed\n\r");
+		return Status;
+	}
+
+	/* Calculate Montgomery Multiplier NPrimeQ */
+	Status = XHdcp22Rx_CalcMontNPrime(InstancePtr->NPrimeQ, (u8 *)PrivateKey->q, XHDCP22_RX_P_SIZE/4);
+	if(Status != XST_SUCCESS)
+	{
+	    xil_printf("ERROR: HDCP22-RX MMult NPrimeQ Generation Failed\n\r");
+	    return Status;
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function reads the version.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Returns the version register of the cipher.
+*
+* @note     None.
+******************************************************************************/
+u32 XHdcp22Rx_GetVersion(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return XHdcp22Cipher_GetVersion(&InstancePtr->CipherInst);
+}
+
+/*****************************************************************************/
+/**
+* This function returns the pointer to the internal timer control instance
+* needed for connecting the timer interrupt to an interrupt controller.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   A pointer to the internal timer control instance.
+*
+* @note     None.
+******************************************************************************/
+XTmrCtr* XHdcp22Rx_GetTimer(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return &InstancePtr->TimerInst;
+}
+
+/*****************************************************************************/
+/**
+* This function copies a complete repeater topology table into the instance
+* repeater topology table.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    TopologyPtr is a pointer to the repeater topology table.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp22Rx_SetTopology(XHdcp22_Rx *InstancePtr, const XHdcp22_Rx_Topology *TopologyPtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TopologyPtr != NULL);
+
+	memcpy(&(InstancePtr->Topology), TopologyPtr, sizeof(XHdcp22_Rx_Topology));
+}
+
+/*****************************************************************************/
+/**
+* This function copies the RECEIVER_ID_LIST into the repeater topology table.
+* Receiver ID list is constructed by appending Receiver IDs in big-endian order.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    ListPtr is a pointer to the Receiver ID list. The list consists
+*           of a contiguous set of bytes stored in big-endian order, with
+*           each Receiver ID occuping five bytes with a maximum of 31
+*           Receiver IDs.
+* @param    ListSize is the number of Receiver IDs in the list. The
+*           list size cannot exceed 31 devices.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp22Rx_SetTopologyReceiverIdList(XHdcp22_Rx *InstancePtr, const u8 *ListPtr, u32 ListSize)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(ListPtr != NULL);
+	Xil_AssertVoid(ListSize <= XHDCP22_RX_MAX_DEVICE_COUNT);
+
+	memcpy(InstancePtr->Topology.ReceiverIdList, ListPtr, (ListSize*XHDCP22_RX_RCVID_SIZE));
+}
+
+/*****************************************************************************/
+/**
+* This function is used to set various fields inside the topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    Field indicates what field of the topology structure to update.
+* @param    Value is the value assigned to the field of the topology structure.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp22Rx_SetTopologyField(XHdcp22_Rx *InstancePtr, XHdcp22_Rx_TopologyField Field, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Field < XHDCP22_RX_TOPOLOGY_INVALID);
+
+	switch(Field)
+	{
+	case XHDCP22_RX_TOPOLOGY_DEPTH :
+		XHdcp22Rx_SetTopologyDepth(InstancePtr, Value);
+		break;
+	case XHDCP22_RX_TOPOLOGY_DEVICECNT :
+		XHdcp22Rx_SetTopologyDeviceCnt(InstancePtr, Value);
+		break;
+	case XHDCP22_RX_TOPOLOGY_MAXDEVSEXCEEDED :
+		XHdcp22Rx_SetTopologyMaxDevsExceeded(InstancePtr, Value);
+		break;
+	case XHDCP22_RX_TOPOLOGY_MAXCASCADEEXCEEDED :
+		XHdcp22Rx_SetTopologyMaxCascadeExceeded(InstancePtr, Value);
+		break;
+	case XHDCP22_RX_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM :
+		XHdcp22Rx_SetTopologyHdcp2LegacyDeviceDownstream(InstancePtr, Value);
+		break;
+	case XHDCP22_RX_TOPOLOGY_HDCP1DEVICEDOWNSTREAM :
+		XHdcp22Rx_SetTopologyHdcp1DeviceDownstream(InstancePtr, Value);
+		break;
+	default:
+		break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is used to indicate that the topology table has been
+* updated and is ready for upstream propagation. Before calling this
+* function ensure that all the fields in the repeater topology table
+* have been updated.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+void XHdcp22Rx_SetTopologyUpdate(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Info.IsTopologyValid = TRUE;
+
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO, XHDCP22_RX_LOG_INFO_TOPOLOGY_UPDATE);
+}
+
+/*****************************************************************************/
+/**
+* This function is gets the type information received from the
+* RepeaterAuth_Stream_Manage message for downstream propagation
+* of management information. This function should be called only
+* after the RepeaterAuth_Stream_Manage message has been received,
+* and can be called inside the user callback function type
+* XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - 0x00: Type 0 Content Stream. May be transmitted by the
+*             HDCP Repeater to all HDCP Devices.
+*           - 0x01: Type 1 Content Stream. Must not be transmitted
+*             by the HDCP Repeater to HDCP 1.x-compliant Devices and
+*             HDCP 2.1-compliant Devices.
+*           - 0x02-0xFF: Reserved for future use only. Content
+*             Streams with reserved Type values must be treated
+*             similar to Type 1 Content Streams.
+*
+* @note     None.
+******************************************************************************/
+u8 XHdcp22Rx_GetContentStreamType(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Params.StreamIdType[1]);
+}
+
+/*****************************************************************************/
+/**
+* This function is called to initialize the cipher.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+******************************************************************************/
+static int XHdcp22Rx_InitializeCipher(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status = XST_SUCCESS;
+	UINTPTR SubcoreBaseAddr;
+	XHdcp22_Cipher_Config *CipherConfigPtr = NULL;
+
+	CipherConfigPtr = XHdcp22Cipher_LookupConfig(InstancePtr->Config.CipherDeviceId);
+	if(CipherConfigPtr == NULL)
+	{
+		return XST_FAILURE;
+	}
+
+	Status = XHdcp22Rx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, CipherConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	Status |= XHdcp22Cipher_CfgInitialize(&InstancePtr->CipherInst, CipherConfigPtr, SubcoreBaseAddr);
+
+	XHdcp22Cipher_SetRxMode(&InstancePtr->CipherInst);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function is called to initialize the modular multiplier.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+******************************************************************************/
+static int XHdcp22Rx_InitializeMmult(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status = XST_SUCCESS;
+	UINTPTR SubcoreBaseAddr;
+	XHdcp22_mmult_Config *MmultConfigPtr;
+
+	MmultConfigPtr = XHdcp22_mmult_LookupConfig(InstancePtr->Config.MontMultDeviceId);
+	if(MmultConfigPtr == NULL)
+	{
+		return XST_FAILURE;
+	}
+
+	Status = XHdcp22Rx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, MmultConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	Status |= XHdcp22_mmult_CfgInitialize(&InstancePtr->MmultInst, MmultConfigPtr, SubcoreBaseAddr);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function is called to initialize the random number generator.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+******************************************************************************/
+static int XHdcp22Rx_InitializeRng(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status = XST_SUCCESS;
+	UINTPTR SubcoreBaseAddr;
+	XHdcp22_Rng_Config *RngConfigPtr;
+
+	RngConfigPtr = XHdcp22Rng_LookupConfig(InstancePtr->Config.RngDeviceId);
+	if(RngConfigPtr == NULL)
+	{
+		return XST_FAILURE;
+	}
+
+	Status |= XHdcp22Rx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, RngConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	Status |= XHdcp22Rng_CfgInitialize(&InstancePtr->RngInst, RngConfigPtr, SubcoreBaseAddr);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function is called to initialize the timer.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+******************************************************************************/
+static int XHdcp22Rx_InitializeTimer(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status = XST_SUCCESS;
+	UINTPTR SubcoreBaseAddr;
+	XTmrCtr_Config *TimerConfigPtr;
+
+	TimerConfigPtr = XTmrCtr_LookupConfig(InstancePtr->Config.TimerDeviceId);
+	if(TimerConfigPtr == NULL)
+	{
+		return XST_FAILURE;
+	}
+
+	Status = XHdcp22Rx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, TimerConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	XTmrCtr_CfgInitialize(&InstancePtr->TimerInst, TimerConfigPtr, SubcoreBaseAddr);
+	if (Status != XST_SUCCESS) {
+		return Status;
+	}
+
+	XTmrCtr_SetOptions(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_0,
+	                   XTC_AUTO_RELOAD_OPTION);
+	XTmrCtr_SetOptions(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_1,
+	                   XTC_INT_MODE_OPTION | XTC_DOWN_COUNT_OPTION);
+	XTmrCtr_SetHandler(&InstancePtr->TimerInst, XHdcp22Rx_TimerHandler,
+	                   InstancePtr);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function handles timer interrupts.
+*
+* @param  CallbackRef refers to a XHdcp22_Rx structure
+* @param  TmrCntNumber the number of used timer.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Rx_TimerHandler(void *CallbackRef, u8 TmrCntNumber)
+{
+	XHdcp22_Rx *InstancePtr = (XHdcp22_Rx *)CallbackRef;
+
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	if (TmrCntNumber == XHDCP22_RX_TMR_CTR_0) {
+		return;
+	}
+
+	/* Set timer expired signaling flag */
+	InstancePtr->Info.TimerExpired = (TRUE);
+
+	/* Log error event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_TIMER_EXPIRED);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function starts the count down timer needed for checking
+* protocol timeouts.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    TimeOut_mSec is the timeout for the next status update.
+*
+* @return   XST_SUCCESS or XST_FAILURE.
+*
+* @note     None.
+*
+******************************************************************************/
+static void XHdcp22Rx_StartTimer(XHdcp22_Rx *InstancePtr, u32 TimeOut_mSec,
+                                u8 ReasonId)
+{
+	u32 Ticks = (u32)(InstancePtr->TimerInst.Config.SysClockFreqHz / 1000000) * TimeOut_mSec * 1000;
+
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	InstancePtr->Info.TimerExpired = (FALSE);
+	InstancePtr->Info.TimerReasonId = ReasonId;
+	InstancePtr->Info.TimerInitialTicks = Ticks;
+
+#ifndef _XHDCP22_RX_DISABLE_TIMEOUT_CHECKING_
+	XTmrCtr_SetResetValue(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_1, Ticks);
+	XTmrCtr_Start(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_1);
+
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG,
+	                XHDCP22_RX_LOG_DEBUG_TIMER_START);
+#endif /* _XHDCP22_RX_DISABLE_TIMEOUT_CHECKING_ */
+}
+
+/*****************************************************************************/
+/**
+*
+* This function stops the count down timer used for protocol timeouts.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    TimeOut_mSec is the timeout for the next status update.
+*
+* @return   XST_SUCCESS or XST_FAILURE.
+*
+* @note     None.
+*
+******************************************************************************/
+static void XHdcp22Rx_StopTimer(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	InstancePtr->Info.TimerExpired = (FALSE);
+
+	XTmrCtr_Stop(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_1);
+}
+
+/*****************************************************************************/
+/**
+* This function computes the subcore absolute address on axi-lite interface
+* Subsystem is mapped at an absolute address and all included sub-cores are
+* at pre-defined offset from the subsystem base address. To access the subcore
+* register map from host CPU an absolute address is required.
+*
+* @param	BaseAddress is the base address of the subsystem instance
+* @param	SubcoreOffset is the offset of the the subcore instance
+* @param	SubcoreAddressPtr is the computed base address of the subcore instance
+*
+* @return	XST_SUCCESS if base address computation is successful and within
+* 			subsystem address range else XST_FAILURE
+*
+******************************************************************************/
+static int XHdcp22Rx_ComputeBaseAddress(UINTPTR BaseAddress, UINTPTR SubcoreOffset, UINTPTR *SubcoreAddressPtr)
+{
+	int Status;
+	UINTPTR Address;
+
+	Address = BaseAddress | SubcoreOffset;
+	if((Address >= BaseAddress))
+	{
+		*SubcoreAddressPtr = Address;
+		Status = XST_SUCCESS;
+	}
+	else
+	{
+		*SubcoreAddressPtr = 0;
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+* This function is used to get a random value Rrx of 64bits for AKEInit.
+* When the test mode is set to XHDCP22_RX_TESTMODE_NO_TX a preloaded test
+* value is copied into the array with pointer RrxPtr. Otherwise, a
+* random value is generated and copied.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	RrxPtr is a pointer to an array where the 64bit Rrx is
+* 			to be copied.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+******************************************************************************/
+static int XHdcp22Rx_GenerateRrx(XHdcp22_Rx *InstancePtr, u8 *RrxPtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(RrxPtr != NULL);
+
+	XHdcp22Rx_GenerateRandom(InstancePtr, XHDCP22_RX_RRX_SIZE, RrxPtr);
+
+#ifdef _XHDCP22_RX_TEST_
+	/* In test mode copy the test vector */
+	XHdcp22Rx_TestGenerateRrx(InstancePtr, RrxPtr);
+#endif
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function is used to check if a complete message is available in
+* the write message buffer. The DDC flag is cleared when a message
+* available is detected.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+static u8 XHdcp22Rx_IsWriteMessageAvailable(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if write message is available then clear flag */
+	if(InstancePtr->Info.DdcFlag & XHDCP22_RX_DDC_FLAG_WRITE_MESSAGE_READY)
+	{
+		InstancePtr->Info.DdcFlag &= ~XHDCP22_RX_DDC_FLAG_WRITE_MESSAGE_READY;
+		return (TRUE);
+	}
+
+	return (FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function is used to check if a complete message has been read
+* out of the read message buffer, indicating that the buffer is empty.
+* The DDC flag is cleared when a read message complete has been detected.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	TRUE or FALSE.
+*
+* @note		None.
+******************************************************************************/
+static u8 XHdcp22Rx_IsReadMessageComplete(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if read message is complete then clear flag */
+	if((InstancePtr->Info.DdcFlag & XHDCP22_RX_DDC_FLAG_READ_MESSAGE_READY))
+		return (TRUE);
+	else
+		return (FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the DDC RxStatus registers (0x70-0x71) MessageSize bits.
+* The HDCP22-RX state machine calls this function immediately after writing
+* a complete message into the read message buffer. The repeater READY bit
+* can also be updated in conjunction to the message size.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param  MessageSize indicates the size in bytes of the message
+*         available in the read message buffer.
+* @param  ReauthReq is set to TRUE to assert the REAUTH_REQ bit.
+* @param  TopologyReady is set to TRUE to assert the READY bit.
+*
+* @return None.
+*
+* @note	  None.
+******************************************************************************/
+static void XHdcp22Rx_SetRxStatus(XHdcp22_Rx *InstancePtr, u16 MessageSize, u8 ReauthReq, u8 TopologyReady)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(MessageSize <= 0x03FF);
+
+	u8 RxStatus[2] = {0, 0};
+
+	/* Update RxStatus[11:0] */
+	RxStatus[1] &= (0x0C00 >> 8);                  // Clear fields except for RxStatus[11:10], REAUTH_REQ and READY
+	RxStatus[0] = (MessageSize & 0x00FF);          // Update RxStatus[7:0], Message_Size
+	RxStatus[1] |= ((MessageSize & 0x0300) >> 8);  // Update RxStatus[9:8], Message_Size
+	if(TopologyReady)
+		RxStatus[1] |= (0x0400 >> 8);                // Set RxStatus[10], READY bit
+	if(ReauthReq)
+		RxStatus[1] |= (0x0800 >> 8);                // Set RxStatus[11], REAUTH_REQ bit
+
+	/* Set RxStatus */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef, XHDCP22_RX_DDC_RXSTATUS0_REG);
+	InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef, RxStatus[0]);
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef, XHDCP22_RX_DDC_RXSTATUS1_REG);
+	InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef, RxStatus[1]);
+
+	/* Clear DDC read message buffer ready */
+	if (MessageSize > 0)
+		InstancePtr->Info.DdcFlag &= ~XHDCP22_RX_DDC_FLAG_READ_MESSAGE_READY;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the DDC RxStatus registers (0x70-0x71) ReauthReq bit
+* and clears the link integrity error flag. Setting the ReauthReq bit
+* signals the transmitter to re-initiate authentication.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+static void XHdcp22Rx_SetDdcReauthReq(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#ifndef _XHDCP22_RX_DISABLE_REAUTH_REQUEST_
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO, XHDCP22_RX_LOG_INFO_REQAUTH_REQ);
+
+	/* Increment re-authentication request count */
+	InstancePtr->Info.ReauthRequestCnt++;
+
+	/* Set the ReauthReq flag */
+	InstancePtr->Info.ReauthReq = TRUE;
+
+	/* Set the RxStatus register */
+	XHdcp22Rx_SetRxStatus(InstancePtr, 0,
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Clear link integrity error flag */
+	InstancePtr->Info.ErrorFlag &= ~XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY;
+#endif /* _XHDCP22_RX_DISABLE_REAUTH_REQUEST_ */
+}
+
+/*****************************************************************************/
+/**
+* This function resets the HDCP22-RX DDC registers to their default values
+* and clears the read/write message buffers. The DDC status flag is set to
+* it's initial state and the DDC error flags are cleared.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	ClrWrBuffer is TRUE to clear the write message buffer.
+* @param	ClrRdBuffer is TRUE to clear the read message buffer.
+* @param	ClrReady is TRUE to clear the READY bit.
+* @param	ClrReauthReq is set to TRUE to clear the REAUTH_REQ bit.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+static void XHdcp22Rx_ResetDdc(XHdcp22_Rx *InstancePtr, u8 ClrWrBuffer,
+	u8 ClrRdBuffer, u8 ClrReady, u8 ClrReauthReq)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->Handles.IsDdcAllCallbacksSet == TRUE);
+
+	/* Clear READY flag */
+	if(ClrReady) {
+		InstancePtr->Info.TopologyReady = FALSE;
+	}
+
+	/* Clear REAUTH_REQ flag */
+	if(ClrReauthReq) {
+		InstancePtr->Info.ReauthReq = FALSE;
+	}
+
+	/* Update RxStatus register */
+	XHdcp22Rx_SetRxStatus(InstancePtr, 0, InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Reset read message buffers */
+	if(ClrRdBuffer)
+	{
+		InstancePtr->Handles.DdcClearReadBufferCallback(InstancePtr->Handles.DdcClearReadBufferCallbackRef);
+		/* Initialize DDC status flag */
+		InstancePtr->Info.DdcFlag = XHDCP22_RX_DDC_FLAG_READ_MESSAGE_READY;
+	}
+
+	/* Reset write message buffers */
+	if(ClrWrBuffer) {
+		InstancePtr->Handles.DdcClearWriteBufferCallback(InstancePtr->Handles.DdcClearWriteBufferCallbackRef);
+	}
+
+	/* Clear DDC error flags */
+	InstancePtr->Info.ErrorFlag &= ~XHDCP22_RX_ERROR_FLAG_DDC_BURST;
+}
+
+/*****************************************************************************/
+/**
+* This function resets the HDCP22-RX system after an error event. The
+* driver calls this function when recovering from error conditions.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+static void XHdcp22Rx_ResetAfterError(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	int AuthenticationStatus = InstancePtr->Info.AuthenticationStatus;
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_FORCE_RESET);
+
+	/* Reset cipher */
+	XHdcp22Cipher_Disable(&InstancePtr->CipherInst);
+	XHdcp22Cipher_Enable(&InstancePtr->CipherInst);
+
+	/* Clear message buffer */
+	memset(&InstancePtr->MessageBuffer, 0, sizeof(XHdcp22_Rx_Message));
+	InstancePtr->MessageSize = 0;
+
+	/* Set default values */
+	InstancePtr->StateFunc = (XHdcp22_Rx_StateFunc)(&XHdcp22Rx_StateB0);
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_UNAUTHENTICATED;
+	InstancePtr->Info.IsNoStoredKm = FALSE;
+	InstancePtr->Info.IsEncrypted = FALSE;
+	InstancePtr->Info.LCInitAttempts = 0;
+	InstancePtr->Info.CurrentState = XHDCP22_RX_STATE_B0_WAIT_AKEINIT;
+	InstancePtr->Info.NextState = XHDCP22_RX_STATE_B0_WAIT_AKEINIT;
+
+	/* Reset repeater values */
+	memset(&InstancePtr->Topology, 0, sizeof(XHdcp22_Rx_Topology));
+	InstancePtr->Info.IsTopologyValid = FALSE;
+	InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+	InstancePtr->Info.SeqNumV = 0;
+	InstancePtr->Info.HasStreamManagementInfo = FALSE;
+	InstancePtr->Info.SkipRead = FALSE;
+
+	/* Disable timer */
+	XHdcp22Rx_StopTimer(InstancePtr);
+
+	/* Reset parameters */
+	XHdcp22Rx_ResetParams(InstancePtr);
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_UNAUTHENTICATED */
+	if((InstancePtr->Handles.IsUnauthenticatedCallbackSet) &&
+		 (AuthenticationStatus == XHDCP22_RX_AUTHENTICATED))
+	{
+		InstancePtr->Handles.UnauthenticatedCallback(InstancePtr->Handles.UnauthenticatedCallbackRef);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function resets the HDCP22-RX parameters stored in memory during the
+* authentication process.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	None.
+*
+* @note		This function is called each time an AKE_Init message is
+*			received.
+******************************************************************************/
+static void XHdcp22Rx_ResetParams(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Clear stored parameters */
+	memset(InstancePtr->Params.Km,           0, sizeof(InstancePtr->Params.Km));
+	memset(InstancePtr->Params.Ks,           0, sizeof(InstancePtr->Params.Ks));
+	memset(InstancePtr->Params.Rn,           0, sizeof(InstancePtr->Params.Rn));
+	memset(InstancePtr->Params.EKh,          0, sizeof(InstancePtr->Params.EKh));
+	memset(InstancePtr->Params.Riv,          0, sizeof(InstancePtr->Params.Riv));
+	memset(InstancePtr->Params.Rrx,          0, sizeof(InstancePtr->Params.Rrx));
+	memset(InstancePtr->Params.Rtx,          0, sizeof(InstancePtr->Params.Rtx));
+	memset(InstancePtr->Params.RxCaps,       0, sizeof(InstancePtr->Params.RxCaps));
+	memset(InstancePtr->Params.TxCaps,       0, sizeof(InstancePtr->Params.TxCaps));
+	memset(InstancePtr->Params.HPrime,       0, sizeof(InstancePtr->Params.HPrime));
+	memset(InstancePtr->Params.LPrime,       0, sizeof(InstancePtr->Params.LPrime));
+	memset(InstancePtr->Params.VPrime,       0, sizeof(InstancePtr->Params.VPrime));
+	memset(InstancePtr->Params.SeqNumM,      0, sizeof(InstancePtr->Params.SeqNumM));
+	memset(InstancePtr->Params.StreamIdType, 0, sizeof(InstancePtr->Params.StreamIdType));
+	memset(InstancePtr->Params.MPrime,       0, sizeof(InstancePtr->Params.MPrime));
+}
+
+/*****************************************************************************/
+/**
+* This function uses polling to read a complete message out of the read
+* message buffer.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return	Size of message read out of read message buffer.
+*
+* @note		None.
+******************************************************************************/
+static int XHdcp22Rx_PollMessage(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 Size = 0;
+	u32 Offset = 0;
+
+	/* Get message */
+	if(XHdcp22Rx_IsWriteMessageAvailable(InstancePtr) == TRUE)
+	{
+		Size = InstancePtr->Handles.DdcGetWriteBufferSizeCallback(InstancePtr->Handles.DdcGetWriteBufferSizeCallbackRef);
+
+		InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef, XHDCP22_RX_DDC_WRITE_REG);
+
+		for(Offset = 0; Offset < Size; Offset++)
+		{
+			InstancePtr->MessageBuffer[Offset] = InstancePtr->Handles.DdcGetDataCallback(InstancePtr->Handles.DdcGetDataCallbackRef);
+		}
+	}
+
+	return Size;
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Receiver State B0 (Unauthenticated). In this
+* state the receiver is awaiting the reception of AKE_Init from the
+* transmitter to trigger the authentication protocol.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     When an unexpected or malformed message is received
+*           the system is reset to a known state to allow graceful
+*           recovery from error.
+******************************************************************************/
+static void *XHdcp22Rx_StateB0(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_UNAUTHENTICATED;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition B0->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+			    InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+			    return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	return (void *)XHdcp22Rx_StateB0;
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Receiver State B1 (ComputeKm). In this
+* state the receiver makes the AKESendCert message available for reading
+* by the transmitter in response to AKEInit. If AKENoStoredKm is received,
+* the receiver decrypts Km with KprivRx and calculates HPrime. If AKEStoredKm
+* is received it decrypts Ekh(Km) to derive Km and calculate HPrime. It makes
+* AKESendHPrime message available for reading immediately after computation
+* of HPrime to ensure that the message is received by the transmitter within
+* the specified 1s timeout at the transmitter for NoStoredKm and 200ms timeout
+* for StoredKm. When AKENoStoredKm is received the AKESendPairingInfo message
+* is made available to the transmitter for reading after within 200ms after
+* AKESendHPrime message is received by the transmitter.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     When an unexpected or malformed message is received the
+*           system is reset to the default state B0 to allow graceful
+*           recovery from error.
+******************************************************************************/
+static void *XHdcp22Rx_StateB1(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT:
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+			    InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+			    break;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_AKENOSTOREDKM:
+			if(InstancePtr->Info.CurrentState == XHDCP22_RX_STATE_B1_WAIT_AKEKM)
+			{
+				Status = XHdcp22Rx_ProcessMessageAKENoStoredKm(InstancePtr);
+				if(Status == XST_SUCCESS)
+				{
+					InstancePtr->Info.IsNoStoredKm = TRUE;
+					InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDHPRIME;
+					break;
+				}
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKENOSTOREDKM);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_AKESTOREDKM:
+			if(InstancePtr->Info.CurrentState == XHDCP22_RX_STATE_B1_WAIT_AKEKM)
+			{
+				Status = XHdcp22Rx_ProcessMessageAKEStoredKm(InstancePtr);
+				if(Status == XST_SUCCESS)
+				{
+					InstancePtr->Info.IsNoStoredKm = FALSE;
+					InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDHPRIME;
+					break;
+				}
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKESTOREDKM);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	/* Message send */
+	switch(InstancePtr->Info.NextState)
+	{
+	case XHDCP22_RX_STATE_B1_SEND_AKESENDCERT:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			Status = XHdcp22Rx_SendMessageAKESendCert(InstancePtr);
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_WAIT_AKEKM;
+		}
+		break;
+	case XHDCP22_RX_STATE_B1_SEND_AKESENDHPRIME:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			Status = XHdcp22Rx_SendMessageAKESendHPrime(InstancePtr);
+			if(InstancePtr->Info.IsNoStoredKm)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDPAIRINGINFO;
+			}
+			else
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_WAIT_LCINIT;
+				return (void *)XHdcp22Rx_StateB2; /* Transition B1->B2 */
+			}
+		}
+		break;
+	case XHDCP22_RX_STATE_B1_SEND_AKESENDPAIRINGINFO:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			Status = XHdcp22Rx_SendMessageAKESendPairingInfo(InstancePtr);
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_WAIT_LCINIT;
+			return (void *)XHdcp22Rx_StateB2;
+		}
+		break;
+	default:
+		break;
+	}
+
+	return (void *)XHdcp22Rx_StateB1;
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Receiver State B2 (Compute_LPrime). The
+* receiver computes LPrime required during locality check and makes
+* LCSendLPrime message available for reading by the transmitter.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     When an unexpected or malformed message is received
+*           the system is reset to the default state B0 to allow
+*           graceful recovery from error.
+******************************************************************************/
+static void *XHdcp22Rx_StateB2(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition B2->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+				return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_LCINIT:
+			/* Maximum of 1024 locality check attempts allowed */
+			if(InstancePtr->Info.CurrentState == XHDCP22_RX_STATE_B1_WAIT_LCINIT ||
+				InstancePtr->Info.CurrentState == XHDCP22_RX_STATE_B2_WAIT_SKESENDEKS)
+			{
+				if(InstancePtr->Info.LCInitAttempts <= XHDCP22_RX_MAX_LCINIT)
+				{
+					Status = XHdcp22Rx_ProcessMessageLCInit(InstancePtr);
+					if(Status == XST_SUCCESS)
+					{
+						InstancePtr->Info.NextState = XHDCP22_RX_STATE_B2_SEND_LCSENDLPRIME;
+						break;
+					}
+				}
+				else
+				{
+					XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MAX_LCINIT_ATTEMPTS);
+				}
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_LCINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_SKESENDEKS: /* Transition B2->B3 */
+			if(InstancePtr->Info.CurrentState == XHDCP22_RX_STATE_B2_WAIT_SKESENDEKS)
+			{
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_B3_COMPUTE_KS;
+			return (void *)XHdcp22Rx_StateB3;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_SKESENDEKS);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	/* Message send */
+	switch(InstancePtr->Info.NextState)
+	{
+	case XHDCP22_RX_STATE_B2_SEND_LCSENDLPRIME:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			Status = XHdcp22Rx_SendMessageLCSendLPrime(InstancePtr);
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_B2_WAIT_SKESENDEKS;
+		}
+		break;
+	default:
+		break;
+	}
+
+	return (void *)XHdcp22Rx_StateB2; /* Transition B2->B2 */
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Receiver State B3 (ComputeKs). The
+* receiver decrypts Edkey(Ks) to derive Ks. The cipher is updated
+* with the session key and enabled within 200ms after the encrypted
+* session key is received.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     When an unexpected or malformed message is received the
+*           system is reset to the default state B0 to allow graceful
+*           recovery from error.
+******************************************************************************/
+static void *XHdcp22Rx_StateB3(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+
+	/* Compute Ks */
+	XHdcp22Rx_ProcessMessageSKESendEks(InstancePtr);
+
+	/* Transition to next state is conditioned on operating mode */
+	if(InstancePtr->Config.Mode == XHDCP22_RX_RECEIVER)
+	{
+		InstancePtr->Info.NextState = XHDCP22_RX_STATE_B4_AUTHENTICATED;
+		return (void *)XHdcp22Rx_StateB4; /* Transition B3->B4, Receiver */
+	}
+	else
+	{
+		InstancePtr->Info.NextState = XHDCP22_RX_STATE_C4_WAIT_FOR_DOWNSTREAM;
+		return (void *)XHdcp22Rx_StateC4; /* Transition B3->C4, Repeater */
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Receiver State B4 (Authenticated). The
+* receiver has completed the authentication protocol. This function
+* executes the XHDCP22_RX_HANDLER_AUTHENTICATED user callback function
+* on transition to this state. An ongoing link integrity check is performed
+* external to the HDCP22-RX system to detect synchronization mismatches
+* between transmitter and receiver. RxStatus REAUTH_REQ bit is set if
+* 50 consecutive data island CRC errors are detected. Setting the REAUTH_REQ
+* bit signals the transmitter to re-initiate authentication.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     When an unexpected or malformed message is received the
+*           system is reset to the default state B0 to allow graceful
+*           recovery from error.
+******************************************************************************/
+static void *XHdcp22Rx_StateB4(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_AUTHENTICATED */
+	if(InstancePtr->Info.CurrentState != InstancePtr->Info.NextState)
+	{
+		if(InstancePtr->Handles.IsAuthenticatedCallbackSet)
+		{
+			InstancePtr->Handles.AuthenticatedCallback(InstancePtr->Handles.AuthenticatedCallbackRef);
+		}
+
+	  /* Start 1 second timer */
+	  XHdcp22Rx_StartTimer(InstancePtr, XHDCP22_RX_ENCRYPTION_STATUS_INTERVAL, 0);
+	}
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_ENCRYPTION_UPDATE */
+	if(InstancePtr->Info.TimerExpired == TRUE)
+	{
+	  Status = XHdcp22Cipher_IsEncrypted(&InstancePtr->CipherInst);
+
+	/* Encryption Enabled */
+	  if((InstancePtr->Info.IsEncrypted != Status)) {
+		  if(InstancePtr->Handles.IsEncryptionStatusCallbackSet)
+		  {
+			InstancePtr->Handles.EncryptionStatusCallback(InstancePtr->Handles.EncryptionStatusCallbackRef);
+		  }
+	}
+
+	  InstancePtr->Info.IsEncrypted = Status;
+
+	  /* Start 1 second timer */
+	  XHdcp22Rx_StartTimer(InstancePtr, XHDCP22_RX_ENCRYPTION_STATUS_INTERVAL, 0);
+	}
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATED;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+	else if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY)
+	{
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_REAUTHENTICATE_REQUESTED;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition B4->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+
+			if(Status == XST_SUCCESS)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+				return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	return (void *)XHdcp22Rx_StateB4; /* Transition B4->B4 */
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Repeater State C4 (WaitForDownstream). In this
+* state the receiver upstream is waiting for all downstream HDCP-protected
+* interface ports of the HDCP Repeater to enter one of the following states:
+* Unconnected (State P0), Unauthenticated (State P1), Authenticated (State F5),
+* or ReceiverIdListAck (State F8). This state checks if the topology table
+* is available for upstream propogation based on the flag set in the function
+* XHdcp22Rx_SetTopologyUpdate by the higher level repeater function.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     If a link integrity problem is detected during this state
+*           then the REAUTH_REQ bit is set in the RxStatus register.
+*           If the RepeaterAuth_Stream_Manage message is received then
+*           transition to State C7 then return back to this state.
+******************************************************************************/
+static void *XHdcp22Rx_StateC4(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Run topology update callback */
+	if((InstancePtr->Info.CurrentState != InstancePtr->Info.NextState) &&
+	(InstancePtr->Handles.IsTopologyUpdateCallbackSet))
+	{
+		InstancePtr->Handles.TopologyUpdateCallback(
+			InstancePtr->Handles.TopologyUpdateCallbackRef);
+	}
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+	else if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY)
+	{
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_REAUTHENTICATE_REQUESTED;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition C4->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+			    InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+			    return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+				XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE: /* Transition C4->C7 */
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT;
+			InstancePtr->Info.ReturnState = InstancePtr->Info.CurrentState;
+			InstancePtr->Info.SkipRead = TRUE;
+			return (void *)XHdcp22Rx_StateC7;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	/* Check the topology update flag */
+	if(InstancePtr->Info.IsTopologyValid == TRUE)
+	{
+		InstancePtr->Info.IsTopologyValid = FALSE;
+		InstancePtr->Info.NextState = XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST;
+		return (void *)XHdcp22Rx_StateC5; /* Transition C4->C5 */
+	}
+
+	return (void *)XHdcp22Rx_StateC4; /* Transition C4->C4 */
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Repeater State C5 (AssembleReceiverIdList).
+* If MAX_DEVS_EXCEEDED or MAX_CASCADE_EXCEEDED is not set then this state
+* calculates VPrime based on the Receiver ID List in the topology table.
+* After VPrime is calculated the Repeaterauth_Send_ReceiverID_List message
+* is populated based on the topology table, VPrime computation, and
+* current seq_num_V counter value. seq_num_V is initialized to a value
+* of zero after AKE_Init and is incremented by one after the transmission
+* of every RepeaterAuth_Send_ReceiverID_List message. The upstream
+* transmitter is responsible for detecting roll over of seq_num_V.
+* The READY bit is asserted once the Repeaterauth_Send_ReceiverID_List
+* message is made available to the upstream and a watchdog timer is set
+* to detect if the acknowledgement arrives within a 2 second period.
+* If the topology maximum flags are asserted in the topology table then
+* the state machine transitions to StateC0 immediately after the
+* Repeaterauth_Send_ReceiverID_List message is read, and the
+* REAUTH_REQ bit is set the in the RxStatus register.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     If a link integrity problem is detected during this state
+*           then the REAUTH_REQ bit is set in the RxStatus register.
+*           If the RepeaterAuth_Stream_Manage message is received then
+*           transition to State C7 then return back to this state.
+******************************************************************************/
+static void *XHdcp22Rx_StateC5(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+	else if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY)
+	{
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_REAUTHENTICATE_REQUESTED;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition C5->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+			    InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+			    return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+				XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE: /* Transition C5->C7 */
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT;
+			InstancePtr->Info.ReturnState = InstancePtr->Info.CurrentState;
+			InstancePtr->Info.SkipRead = TRUE;
+			return (void *)XHdcp22Rx_StateC7;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	/* Message send */
+	switch(InstancePtr->Info.NextState)
+	{
+	case XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			Status = XHdcp22Rx_SendMessageRepeaterAuthSendRxIdList(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST_DONE;
+			}
+			else
+			{
+				XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+					XHDCP22_RX_ERROR_FLAG_EMPTY_REPEATER_TOPOLOGY);
+				XHdcp22Rx_ResetAfterError(InstancePtr);
+				XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+				return (void *)XHdcp22Rx_StateB0; /* Transition C5->B0 */
+			}
+		}
+		break;
+	case XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST_DONE:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			XHdcp22Rx_ResetDdc(InstancePtr, FALSE, FALSE, TRUE, FALSE);
+
+			if(InstancePtr->Topology.MaxDevsExceeded == TRUE ||
+				InstancePtr->Topology.MaxCascadeExceeded == TRUE)
+			{
+				XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+					XHDCP22_RX_ERROR_FLAG_MAX_REPEATER_TOPOLOGY);
+				XHdcp22Rx_ResetAfterError(InstancePtr);
+				XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+				return (void *)XHdcp22Rx_StateB0; /* Transition C5->B0 */
+			}
+			else
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_C6_VERIFY_RECEIVERIDLISTACK;
+				return (void *)XHdcp22Rx_StateC6; /* Transition C5->C6 */
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return (void *)XHdcp22Rx_StateC5; /* Transition C5->C5 */
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Repeater State C6 (VerifyReceiverIdListAck).
+* The RepeaterAuth_Send_Ack message should be available for the receiver
+* upstream interface within two seconds from when the READY bit in the
+* RxStatus register was set in State C5. If the message is not
+* available within the two second window then the state machine
+* transitions back into the un-authenticated state. If the message
+* is received in-time and the least significant 128-bits of V and VPrime
+* match, this indicated successful upstream transmission of topology
+* information and triggers a transition to State C7. If there is a
+* mismatch then the state machine transitions back to the un-authenticated
+* state, and the REAUTH_REQ bit is set in the RxStatus Register.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     If a link integrity problem is detected during this state
+*           then the REAUTH_REQ bit is set in the RxStatus register.
+*           If the RepeaterAuth_Stream_Manage message is received then
+*           transition to State C7 then return back to this state.
+******************************************************************************/
+static void *XHdcp22Rx_StateC6(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+	else if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY)
+	{
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_REAUTHENTICATE_REQUESTED;
+	}
+
+	/* Check timeout for RepeaterAuth_Send_Ack message */
+	if(InstancePtr->Info.TimerExpired == TRUE)
+	{
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0; /* Transition C6->B0 */
+	}
+
+	/* Check if message is available.
+	   When SkipRead flag is set, this indicates that a message has
+	   already been read by another state and should get processed
+	   by this state; therefore, skip the first read. */
+	if(InstancePtr->Info.SkipRead != TRUE)
+	{
+		InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+	}
+	InstancePtr->Info.SkipRead = FALSE;
+
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition C6->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+			    InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+			    return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+				XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE: /* Transition C6->C7 */
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT;
+			InstancePtr->Info.ReturnState = InstancePtr->Info.CurrentState;
+			InstancePtr->Info.SkipRead = TRUE;
+			return (void *)XHdcp22Rx_StateC7;
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSENDACK:
+			Status = XHdcp22Rx_ProcessMessageRepeaterAuthSendAck(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+				if(InstancePtr->Info.HasStreamManagementInfo == TRUE) /* Transition C6->C8 */
+				{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_C8_AUTHENTICATED;
+				return (void *)XHdcp22Rx_StateC8;
+				}
+				else /* Transition C6->C7 */
+				{
+					if(InstancePtr->Info.ReturnState == XHDCP22_RX_STATE_UNDEFINED)
+					{
+					InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT;
+					return (void *)XHdcp22Rx_StateC7;
+					}
+					else
+					{
+						InstancePtr->Info.NextState = InstancePtr->Info.ReturnState;
+						switch(InstancePtr->Info.ReturnState)
+						{
+						case XHDCP22_RX_STATE_C7_SEND_STREAM_READY:
+							InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+							return (void *)XHdcp22Rx_StateC7;
+						default:
+							break;
+						}
+					}
+				}
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+				XHDCP22_RX_ERROR_FLAG_PROCESSING_REPEATERAUTHSENDACK);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0; /* Transition C6->B0 */
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	return (void *)XHdcp22Rx_StateC6; /* Transition C6->C6 */
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Repeater State C7 (ContentStreamManagement).
+* This state waits to receive the RepeaterAuth_Stream_Manage message from
+* the upstream transmitter. Once the message is received the MPrime value is
+* computed and made available to the upstream transmitter to read as part of
+* the RepeaterAuth_Stream_Ready message. Note that state executes in parallel
+* with the upstream propagation of topology information (State C4, State C5,
+* and State C6). A transition in to this state may occur from State C4,
+* State C5, or State C6 if content stream management information is received
+* from the upstream transmitter. Also, the transition from State C7 may
+* return to the appropriate state to allow undisrupted operation.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     If a link integrity problem is detected during this state
+*           then the REAUTH_REQ bit is set in the RxStatus register.
+*           If the RepeaterAuth_Stream_Manage message is received then
+*           transition to State C7 then return back to this state.
+******************************************************************************/
+static void *XHdcp22Rx_StateC7(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+	else if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY)
+	{
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_REAUTHENTICATE_REQUESTED;
+	}
+
+	/* Check if message is available.
+	   When SkipRead flag is set, this indicates that a message has
+	   already been read by another state and should get processed
+	   by this state; therefore, skip the first read. */
+	if(InstancePtr->Info.SkipRead != TRUE)
+	{
+		InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+	}
+	InstancePtr->Info.SkipRead = FALSE;
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition C7->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+				return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+				XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSENDACK:
+			InstancePtr->Info.NextState = InstancePtr->Info.ReturnState;
+			InstancePtr->Info.ReturnState = InstancePtr->Info.CurrentState;
+			InstancePtr->Info.SkipRead = TRUE;
+			return (void *)XHdcp22Rx_StateC6; /* Transition C7->C6 */
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE:
+			Status = XHdcp22Rx_ProcessMessageRepeaterAuthStreamManage(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_SEND_STREAM_READY;
+				break;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+				XHDCP22_RX_ERROR_FLAG_PROCESSING_REPEATERAUTHSTREAMMANAGE);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0; /* Transition C7->B0 */
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	/* Message send */
+	switch(InstancePtr->Info.NextState)
+	{
+	case XHDCP22_RX_STATE_C7_SEND_STREAM_READY:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			Status = XHdcp22Rx_SendMessageRepeaterAuthStreamReady(InstancePtr);
+			InstancePtr->Info.HasStreamManagementInfo = TRUE;
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_SEND_STREAM_READY_DONE;
+		}
+		break;
+	case XHDCP22_RX_STATE_C7_SEND_STREAM_READY_DONE:
+		if(XHdcp22Rx_IsReadMessageComplete(InstancePtr) == TRUE)
+		{
+			if(InstancePtr->Info.ReturnState == XHDCP22_RX_STATE_UNDEFINED)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_C8_AUTHENTICATED;
+				return (void *)XHdcp22Rx_StateC8; /* Transition C7->C8 */
+			}
+			else
+			{
+				InstancePtr->Info.NextState = InstancePtr->Info.ReturnState;
+				switch(InstancePtr->Info.ReturnState)
+				{
+				case XHDCP22_RX_STATE_C4_WAIT_FOR_DOWNSTREAM:
+					InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+					return (void *)XHdcp22Rx_StateC4; /* Transition C7->C4 */
+				case XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST:
+					InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+					return (void *)XHdcp22Rx_StateC5; /* Transition C7->C5 */
+				case XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST_DONE:
+					InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+					return (void *)XHdcp22Rx_StateC5; /* Transition C7->C5 */
+				case XHDCP22_RX_STATE_C6_VERIFY_RECEIVERIDLISTACK:
+					InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+					return (void *)XHdcp22Rx_StateC6; /* Transition C7->C6 */
+				case XHDCP22_RX_STATE_C8_AUTHENTICATED:
+					InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+					return (void *)XHdcp22Rx_StateC8; /* Transition C7->C8 */
+				default:
+					break;
+				}
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return (void *)XHdcp22Rx_StateC7; /* Transition C7->C7 */
+}
+
+/*****************************************************************************/
+/**
+* This function implements the Receiver State C8 (Authenticated). The
+* repeater has completed the authentication protocol. Upon detection
+* of any changes to the topology a transition back to State C5
+* (AssembleReceiverIdList) occurs. Change to the topology occur when
+* a repeater downstream port has transitioned to the following:
+* authenticated, unauthenticated, or unconnected. This function
+* executes the XHDCP22_RX_HANDLER_AUTHENTICATED user callback function
+* on transition to this state. An ongoing link integrity check is performed
+* external to the HDCP22-RX system to detect synchronization mismatches
+* between transmitter and receiver. RxStatus REAUTH_REQ bit is set if
+* 50 consecutive data island CRC errors are detected. Setting the REAUTH_REQ
+* bit signals the transmitter to re-initiate authentication.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   Pointer to the function that implements the next state.
+*
+* @note     When an unexpected or malformed message is received the
+*           system is reset to the default state B0 to allow graceful
+*           recovery from error.
+******************************************************************************/
+static void *XHdcp22Rx_StateC8(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_AUTHENTICATED
+	   Only run once and clear params */
+	if(InstancePtr->Info.CurrentState != InstancePtr->Info.NextState)
+	{
+	    if(InstancePtr->Handles.IsAuthenticatedCallbackSet)
+		{
+			InstancePtr->Handles.AuthenticatedCallback(InstancePtr->Handles.AuthenticatedCallbackRef);
+		}
+
+	  /* Start 1 second timer */
+	  XHdcp22Rx_StartTimer(InstancePtr, XHDCP22_RX_ENCRYPTION_STATUS_INTERVAL, 0);
+	}
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_ENCRYPTION_UPDATE */
+	if(InstancePtr->Info.TimerExpired == TRUE)
+	{
+	  Status = XHdcp22Cipher_IsEncrypted(&InstancePtr->CipherInst);
+
+	/* Encryption Enabled */
+	  if((InstancePtr->Info.IsEncrypted != Status)) {
+		  if(InstancePtr->Handles.IsEncryptionStatusCallbackSet)
+		  {
+			InstancePtr->Handles.EncryptionStatusCallback(InstancePtr->Handles.EncryptionStatusCallbackRef);
+		  }
+	}
+
+	  InstancePtr->Info.IsEncrypted = Status;
+
+	  /* Start 1 second timer */
+	  XHdcp22Rx_StartTimer(InstancePtr, XHDCP22_RX_ENCRYPTION_STATUS_INTERVAL, 0);
+	}
+
+	/* Update state */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_AUTHENTICATED;
+	InstancePtr->Info.CurrentState = InstancePtr->Info.NextState;
+
+	/* Check error condition */
+	if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_DDC_BURST)
+	{
+		XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+		XHdcp22Rx_ResetAfterError(InstancePtr);
+		return (void *)XHdcp22Rx_StateB0;
+	}
+	else if(InstancePtr->Info.ErrorFlag & XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY)
+	{
+		XHdcp22Rx_SetDdcReauthReq(InstancePtr);
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_RX_REAUTHENTICATE_REQUESTED;
+	}
+
+	/* Check if message is available */
+	InstancePtr->MessageSize = XHdcp22Rx_PollMessage(InstancePtr);
+
+	/* Message handling */
+	if(InstancePtr->MessageSize > 0)
+	{
+		switch(MsgPtr->MsgId)
+		{
+		case XHDCP22_RX_MSG_ID_AKEINIT: /* Transition C8->B1 */
+			Status = XHdcp22Rx_ProcessMessageAKEInit(InstancePtr);
+			if(Status == XST_SUCCESS)
+			{
+				InstancePtr->Info.NextState = XHDCP22_RX_STATE_B1_SEND_AKESENDCERT;
+				return (void *)XHdcp22Rx_StateB1;
+			}
+			XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT);
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE:
+			InstancePtr->Info.NextState = XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT;
+			InstancePtr->Info.ReturnState = InstancePtr->Info.CurrentState;
+			InstancePtr->Info.SkipRead = TRUE;
+			return (void *)XHdcp22Rx_StateC7;
+		default:
+			XHdcp22Rx_ResetAfterError(InstancePtr);
+			return (void *)XHdcp22Rx_StateB0;
+		}
+	}
+
+	/* Check the topology update flag */
+	if(InstancePtr->Info.IsTopologyValid == TRUE)
+	{
+		InstancePtr->Info.IsTopologyValid = FALSE;
+		InstancePtr->Info.NextState = XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST;
+		return (void *)XHdcp22Rx_StateC5; /* Transition C8->C5 */
+	}
+
+	return (void *)XHdcp22Rx_StateC8; /* Transition C8->C8 */
+}
+
+/*****************************************************************************/
+/**
+* This function processes the AKE_Init message received from the transmitter.
+* The stored authentication parameters are reset so that no state
+* information is stored between authentication attempts. The DDC
+* registers are reset to their default value including the REAUTH_REQ
+* flag. The cipher is disabled.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message processed successfully.
+*           - XST_FAILURE if message size is incorrect.
+*
+* @note     None.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageAKEInit(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_AKEINIT);
+
+	/* Increment authentication request count */
+	InstancePtr->Info.AuthRequestCnt++;
+
+	/* Reset cipher */
+	XHdcp22Cipher_Disable(&InstancePtr->CipherInst);
+	XHdcp22Cipher_Enable(&InstancePtr->CipherInst);
+
+	/* Reset timer counter */
+	XTmrCtr_Reset(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_0);
+	XHdcp22Rx_StopTimer(InstancePtr);
+
+	/* Reset repeater values */
+	memset(&InstancePtr->Topology, 0, sizeof(XHdcp22_Rx_Topology));
+	InstancePtr->Info.ReauthReq = FALSE;
+	InstancePtr->Info.TopologyReady = FALSE;
+	InstancePtr->Info.IsTopologyValid = FALSE;
+	InstancePtr->Info.ReturnState = XHDCP22_RX_STATE_UNDEFINED;
+	InstancePtr->Info.SeqNumV = 0;
+	InstancePtr->Info.HasStreamManagementInfo = FALSE;
+	InstancePtr->Info.SkipRead = FALSE;
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_AKEInit))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Reset state variables and DDC registers */
+	XHdcp22Rx_ResetParams(InstancePtr);
+	XHdcp22Rx_ResetDdc(InstancePtr, FALSE, TRUE, TRUE, TRUE);
+
+	/* Record Rtx and TxCaps parameters */
+	memcpy(InstancePtr->Params.Rtx, MsgPtr->AKEInit.Rtx, XHDCP22_RX_RTX_SIZE);
+	memcpy(InstancePtr->Params.TxCaps, MsgPtr->AKEInit.TxCaps, XHDCP22_RX_TXCAPS_SIZE);
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_UNAUTHENTICATED */
+	if((InstancePtr->Handles.IsUnauthenticatedCallbackSet) &&
+		 (InstancePtr->Info.AuthenticationStatus == XHDCP22_RX_AUTHENTICATED))
+	{
+		InstancePtr->Handles.UnauthenticatedCallback(InstancePtr->Handles.UnauthenticatedCallbackRef);
+	}
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_AUTHENTICATION_REQUEST */
+	if(InstancePtr->Handles.IsAuthenticationRequestCallbackSet)
+	{
+		InstancePtr->Handles.AuthenticationRequestCallback(
+			InstancePtr->Handles.AuthenticationRequestCallbackRef);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function generates the AKE_Send_Cert message and writes it into the
+* read message buffer. After the complete message has been written to the
+* buffer the MessageSize is set in the DDC RxStatus register signaling
+* the transmitter that the message is available for reading.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message written successfully.
+*           - XST_FAILURE if generation of random integer Rrx failed.
+*
+* @note     This message must be available for the transmitter with 100ms
+*           after receiving AKEInit.
+******************************************************************************/
+static int XHdcp22Rx_SendMessageAKESendCert(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 Offset = 0;
+	int Status = XST_SUCCESS;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Generate AKE_Send_Cert message */
+	MsgPtr->AKESendCert.MsgId = XHDCP22_RX_MSG_ID_AKESENDCERT;
+	memcpy(MsgPtr->AKESendCert.RxCaps, InstancePtr->RxCaps, XHDCP22_RX_RXCAPS_SIZE);
+	Status = XHdcp22Rx_GenerateRrx(InstancePtr, MsgPtr->AKESendCert.Rrx);
+	memcpy(MsgPtr->AKESendCert.CertRx, InstancePtr->PublicCertPtr, XHDCP22_RX_CERT_SIZE);
+
+	/* Write message to read buffer */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef,
+		XHDCP22_RX_DDC_READ_REG);
+	for(Offset = 0; Offset < sizeof(XHdcp22_Rx_AKESendCert); Offset++)
+	{
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef,
+			InstancePtr->MessageBuffer[Offset]);
+	}
+
+	/* Write message size signaling completion */
+	XHdcp22Rx_SetRxStatus(InstancePtr, sizeof(XHdcp22_Rx_AKESendCert),
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Record Rrx and RxCaps */
+	memcpy(InstancePtr->Params.Rrx, MsgPtr->AKESendCert.Rrx, XHDCP22_RX_RRX_SIZE);
+	memcpy(InstancePtr->Params.RxCaps, MsgPtr->AKESendCert.RxCaps, XHDCP22_RX_RXCAPS_SIZE);
+
+	/* Log message write completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_AKESENDCERT);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function processes the AKE_No_Stored_km message received from the
+* transmitter. The RSAES-OAEP operation decrypts Km with the receiver
+* private key.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message processed successfully.
+*           - XST_FAILURE if message size is incorrect or Km
+*             decryption failed.
+*
+* @note     None.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageAKENoStoredKm(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Size;
+	int Status = XST_SUCCESS;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_AKENOSTOREDKM);
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_AKENoStoredKm))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Compute Km, Perform RSA decryption */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_KM);
+	Status = XHdcp22Rx_RsaesOaepDecrypt(InstancePtr, (XHdcp22_Rx_KprivRx *)(InstancePtr->PrivateKeyPtr),
+										MsgPtr->AKENoStoredKm.EKpubKm, InstancePtr->Params.Km, &Size);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_KM_DONE);
+
+	return (Status == XST_SUCCESS && Size == XHDCP22_RX_KM_SIZE) ? XST_SUCCESS : XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+* This function processes the AKE_Stored_km message received from the
+* transmitter. Decrypts Ekh(Km) using AES with the received m as
+* input and Kh as key into the AES module.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message processed successfully.
+*           - XST_FAILURE if message size is incorrect.
+*
+* @note     None.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageAKEStoredKm(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status = XST_SUCCESS;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_AKESTOREDKM);
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_AKEStoredKm))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Compute Km */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_KM);
+	XHdcp22Rx_ComputeEkh(InstancePtr->PrivateKeyPtr, MsgPtr->AKEStoredKm.EKhKm, MsgPtr->AKEStoredKm.M,
+		InstancePtr->Params.Km);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_KM_DONE);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function computes HPrime, generates AKE_Send_H_prime message, and
+* writes it into the read message buffer. After the complete message has
+* been written to the buffer the MessageSize is set in the DDC RxStatus
+* register signaling the transmitter that the message is available for
+* reading.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   XST_SUCCESS.
+*
+* @note     This message must be available for the transmitter within
+*           1s after receiving AKENoStoredKm or 200ms after receiving
+*           AKEStoredKm.
+******************************************************************************/
+static int XHdcp22Rx_SendMessageAKESendHPrime(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 Offset;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Compute H Prime */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_HPRIME);
+	XHdcp22Rx_ComputeHPrime(InstancePtr->Params.Rrx, InstancePtr->Params.RxCaps,
+			InstancePtr->Params.Rtx, InstancePtr->Params.TxCaps, InstancePtr->Params.Km,
+			MsgPtr->AKESendHPrime.HPrime);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_HPRIME_DONE);
+
+	/* Generate AKE_Send_H_prime message */
+	MsgPtr->AKESendHPrime.MsgId = XHDCP22_RX_MSG_ID_AKESENDHPRIME;
+
+	/* Write message to buffer */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef,
+		XHDCP22_RX_DDC_READ_REG);
+	for(Offset = 0; Offset < sizeof(XHdcp22_Rx_AKESendHPrime); Offset++)
+	{
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef,
+			InstancePtr->MessageBuffer[Offset]);
+	}
+
+	/* Write message size signaling completion */
+	XHdcp22Rx_SetRxStatus(InstancePtr, sizeof(XHdcp22_Rx_AKESendHPrime),
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Record HPrime */
+	memcpy(InstancePtr->Params.HPrime, MsgPtr->AKESendHPrime.HPrime, XHDCP22_RX_HPRIME_SIZE);
+
+	/* Log message write completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_AKESENDHPRIME);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function computes Ekh(Km), generates AKE_Send_Pairing_Info message,
+* and writes it into the read message buffer. After the complete message
+* has been written to the buffer the MessageSize is set in the DDC RxStatus
+* register signaling the transmitter that the message is available for
+* reading.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   XST_SUCCESS.
+*
+* @note     The AKESendPairingInfo message is sent only in response to
+*           receiving AKENoStoredKm message. This message must be
+*           available for the transmitter within 200ms after sending
+*           AKESendHPrime.
+******************************************************************************/
+static int XHdcp22Rx_SendMessageAKESendPairingInfo(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u8 M[XHDCP22_RX_RTX_SIZE+XHDCP22_RX_RRX_SIZE];
+	u8 EKhKm[XHDCP22_RX_EKH_SIZE];
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+	u32 Offset;
+
+	/* Concatenate M = (Rtx || Rrx) */
+	memcpy(M, InstancePtr->Params.Rtx, XHDCP22_RX_RTX_SIZE);
+	memcpy(M+XHDCP22_RX_RTX_SIZE, InstancePtr->Params.Rrx, XHDCP22_RX_RRX_SIZE);
+
+	/* Compute Ekh */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_EKH);
+	XHdcp22Rx_ComputeEkh(InstancePtr->PrivateKeyPtr, InstancePtr->Params.Km, M, EKhKm);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_EKH_DONE);
+
+	/* Generate AKE_Send_Pairing_Info message */
+	MsgPtr->AKESendPairingInfo.MsgId = XHDCP22_RX_MSG_ID_AKESENDPAIRINGINFO;
+	memcpy(MsgPtr->AKESendPairingInfo.EKhKm, EKhKm, XHDCP22_RX_EKH_SIZE);
+
+	/* Write message to buffer */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef,
+		XHDCP22_RX_DDC_READ_REG);
+	for(Offset = 0; Offset < sizeof(XHdcp22_Rx_AKESendPairingInfo); Offset++)
+	{
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef,
+			InstancePtr->MessageBuffer[Offset]);
+	}
+
+	/* Write message size signaling completion */
+	XHdcp22Rx_SetRxStatus(InstancePtr, sizeof(XHdcp22_Rx_AKESendPairingInfo),
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Record Ekh */
+	memcpy(InstancePtr->Params.EKh, EKhKm, XHDCP22_RX_EKH_SIZE);
+
+	/* Log message write completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_AKESENDPAIRINGINFO);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function processes the LC_Init message received from the
+* transmitter. The locality check attempts is incremented for
+* each LCInit message received. The random nonce Rn is recorded.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message processed successfully.
+*           - XST_FAILURE if message size is incorrect.
+*
+* @note     None.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageLCInit(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_LCINIT);
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_LCInit))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Update locality check attempts */
+	InstancePtr->Info.LCInitAttempts++;
+
+	/* Record Rn parameter */
+	memcpy(InstancePtr->Params.Rn, MsgPtr->LCInit.Rn, XHDCP22_RX_RN_SIZE);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function computes LPrime, generates LC_Send_L_prime message,
+* and writes it into the read message buffer. After the complete message
+* has been written to the buffer the MessageSize is set in the DDC RxStatus
+* register signaling the transmitter that the message is available for
+* reading.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   XST_SUCCESS.
+*
+* @note     The LCSendLPrime message must be available for the transmitter
+*           within 20ms after receiving LCInit.
+******************************************************************************/
+static int XHdcp22Rx_SendMessageLCSendLPrime(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+	u32 Offset;
+
+	/* Compute LPrime */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_LPRIME);
+	XHdcp22Rx_ComputeLPrime(InstancePtr->Params.Rn, InstancePtr->Params.Km, InstancePtr->Params.Rrx,
+		InstancePtr->Params.Rtx, MsgPtr->LCSendLPrime.LPrime);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_LPRIME_DONE);
+
+	/* Generate LC_Send_L_prime message */
+	MsgPtr->LCSendLPrime.MsgId = XHDCP22_RX_MSG_ID_LCSENDLPRIME;
+
+	/* Write message to buffer */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef,
+		XHDCP22_RX_DDC_READ_REG);
+	for(Offset = 0; Offset < sizeof(XHdcp22_Rx_LCSendLPrime); Offset++)
+	{
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef,
+			InstancePtr->MessageBuffer[Offset]);
+	}
+
+	/* Write message size signaling completion */
+	XHdcp22Rx_SetRxStatus(InstancePtr, sizeof(XHdcp22_Rx_LCSendLPrime),
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Record LPrime parameter */
+	memcpy(InstancePtr->Params.LPrime, MsgPtr->LCSendLPrime.LPrime, XHDCP22_RX_LPRIME_SIZE);
+
+	/* Log message write completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_LCSENDLPRIME);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function processes the SKE_Send_Eks message received from the
+* transmitter. The session key Ks is decrypted and written to the
+* cipher.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message processed successfully.
+*           - XST_FAILURE if message size is incorrect.
+*
+* @note     The cipher must be enabled within 200ms after receiving
+*           SKESendEks.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageSKESendEks(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_SKESENDEKS);
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_SKESendEks))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Compute Ks */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_KS);
+	XHdcp22Rx_ComputeKs(InstancePtr->Params.Rrx, InstancePtr->Params.Rtx, InstancePtr->Params.Km,
+						InstancePtr->Params.Rn, MsgPtr->SKESendEks.EDkeyKs, InstancePtr->Params.Ks);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_KS_DONE);
+
+	/* Record Riv parameter */
+	memcpy(InstancePtr->Params.Riv, MsgPtr->SKESendEks.Riv, XHDCP22_RX_RIV_SIZE);
+
+	/* Load cipher Ks and Riv */
+	XHdcp22Cipher_SetKs(&InstancePtr->CipherInst, InstancePtr->Params.Ks, XHDCP22_RX_KS_SIZE);
+	XHdcp22Cipher_SetRiv(&InstancePtr->CipherInst, InstancePtr->Params.Riv, XHDCP22_RX_RIV_SIZE);
+
+	/* Log info event */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO, XHDCP22_RX_LOG_INFO_ENCRYPTION_ENABLE);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function generates the RepeaterAuth_Send_ReceiverID_List message
+* and writes it into the read message buffer. After the complete message
+* has been written to the buffer the MessageSize and READY fields are set
+* in the DDC RxStatus register signaling the transmitter that the message
+* is available for reading. When the topology maximums are not exceeded
+* VPrime is computed. seq_num_v is incremented after the transmission of
+* each RepeaterAuth_Send_ReceiverID_List message. The READY bit in the
+* RxStatus register is cleared automatically.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if device count is equal to zero.
+*           - XST_FAILURE if device count is greater than zero.
+*
+* @note     The RepeaterAuth_Send_ReceiverID_List must be available
+*           and READY bit asserted in the RxStatus register for
+*           the upstream transmitter within 3 seconds.
+******************************************************************************/
+static int XHdcp22Rx_SendMessageRepeaterAuthSendRxIdList(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+	u32 Offset;
+	u32 MessageSize;
+
+	/* Set message ID */
+	MsgPtr->RepeaterAuthSendRxIdList.MsgId      =
+		XHDCP22_RX_MSG_ID_REPEATERAUTHSENDRXIDLIST;
+
+	/* Set RxInfo bit fields */
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[0]  =
+		(u8)((InstancePtr->Topology.Depth & 0x07) << 1);                    // RxInfo[11:9] = Depth[2:0]
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[0] |=
+		(u8)((InstancePtr->Topology.DeviceCnt & 0x10) >> 4);                // RxInfo[8]    = DeviceCnt[4]
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[1]  =
+		(u8)((InstancePtr->Topology.DeviceCnt & 0x0F) << 4);                // RxInfo[7:4]  = DeviceCnt[3:0]
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[1] |=
+		(u8)((InstancePtr->Topology.MaxDevsExceeded & 0x01) << 3);          // RxInfo[3]    = MaxDevsExceeded
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[1] |=
+		(u8)((InstancePtr->Topology.MaxCascadeExceeded & 0x01) << 2);       // RxInfo[2]    = MaxCascadeExceeded
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[1] |=
+		(u8)((InstancePtr->Topology.Hdcp2LegacyDeviceDownstream & 0x01) << 1); // RxInfo[1]    = Hdcp2LegacyDeviceDownstream
+	MsgPtr->RepeaterAuthSendRxIdList.RxInfo[1] |=
+		(u8)(InstancePtr->Topology.Hdcp1DeviceDownstream & 0x01);           // RxInfo[0]    = Hdcp1DeviceDownstream
+
+	/* Set seq_numb_V bytes */
+	MsgPtr->RepeaterAuthSendRxIdList.SeqNumV[0] = (InstancePtr->Info.SeqNumV >> 16) & 0xFF;
+	MsgPtr->RepeaterAuthSendRxIdList.SeqNumV[1] = (InstancePtr->Info.SeqNumV >> 8) & 0xFF;
+	MsgPtr->RepeaterAuthSendRxIdList.SeqNumV[2] = (InstancePtr->Info.SeqNumV) & 0xFF;
+
+	/* Set other message fields
+	 * - When topology maximums are not exceeded send seq_num_V, VPrime, and Receiver ID List
+	 * - Otherwise, only send RxInfo
+	 */
+	if(InstancePtr->Topology.MaxDevsExceeded != TRUE &&
+		InstancePtr->Topology.MaxCascadeExceeded != TRUE)
+	{
+		/* Increment seq_num_V count with rollover */
+		InstancePtr->Info.SeqNumV = (InstancePtr->Info.SeqNumV + 1) % XHDCP22_RX_MAX_SEQNUMV;
+
+		/* Compute VPrime */
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_VPRIME);
+		XHdcp22Rx_ComputeVPrime((u8 *)InstancePtr->Topology.ReceiverIdList,
+			InstancePtr->Topology.DeviceCnt,
+			MsgPtr->RepeaterAuthSendRxIdList.RxInfo,
+			MsgPtr->RepeaterAuthSendRxIdList.SeqNumV,
+			InstancePtr->Params.Km,
+			InstancePtr->Params.Rrx,
+			InstancePtr->Params.Rtx,
+			InstancePtr->Params.VPrime);
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_VPRIME_DONE);
+
+		/* Copy VPrime[0:16], most significant 128-bits */
+		memcpy(MsgPtr->RepeaterAuthSendRxIdList.VPrime, InstancePtr->Params.VPrime, 16);
+
+		/* Copy receiver ID list */
+		memcpy(MsgPtr->RepeaterAuthSendRxIdList.ReceiverIdList,
+				InstancePtr->Topology.ReceiverIdList,
+				XHDCP22_RX_RCVID_SIZE*InstancePtr->Topology.DeviceCnt);
+
+		/* Update message size */
+		MessageSize = 22 + XHDCP22_RX_RCVID_SIZE*InstancePtr->Topology.DeviceCnt;
+	}
+	else
+	{
+		/* Update message size */
+		MessageSize = 3;
+	}
+
+	/* Write message to buffer */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef,
+		XHDCP22_RX_DDC_READ_REG);
+	for(Offset = 0; Offset < MessageSize; Offset++)
+	{
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef,
+			InstancePtr->MessageBuffer[Offset]);
+	}
+
+	/* Set the TopologyReady flag */
+	InstancePtr->Info.TopologyReady = TRUE;
+
+	/* Write message size and assert the RxStatus READY bit signaling completion */
+	XHdcp22Rx_SetRxStatus(InstancePtr, MessageSize,
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Start 2 second timer */
+	XHdcp22Rx_StartTimer(InstancePtr, XHDCP22_RX_REPEATERAUTH_ACK_INTERVAL, 0);
+
+	/* Log message write completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_REPEATERAUTHSENDRXIDLIST);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function processes the RepeaterAuth_Send_Ack message received from
+* the upstream transmitter. The least significant 128-bits of the value
+* V are compared against VPrime. The timer is stopped.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS when V and VPrime match.
+*           - XST_FAILURE when V and VPrime do not match.
+*
+* @note     The RepeaterAuth_Send_Ack message must be available for the
+*           repeater upstream interface within 2 seconds after asserting
+*           the READY bit in the RxStatus register.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageRepeaterAuthSendAck(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Status;
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Stop the timer */
+	XHdcp22Rx_StopTimer(InstancePtr);
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr,
+		XHDCP22_RX_LOG_EVT_INFO_MESSAGE,
+		XHDCP22_RX_MSG_ID_REPEATERAUTHSENDACK);
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_RepeaterAuthSendAck))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR, XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Compare LSb's of V and VPrime */
+	Status = memcmp(MsgPtr->RepeaterAuthSendAck.V, InstancePtr->Params.VPrime+16, 16);
+
+	return (Status == 0) ? XST_SUCCESS : XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+* This function processes the RepeaterAuth_Repeater_Manage message.
+* The message values seq_num_M and StreamID_Type are stored for
+* later computation of MPrime. The user callback function
+* type XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST is executed.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   - XST_SUCCESS if message processed successfully.
+*           - XST_FAILURE if message size is incorrect.
+*
+* @note     After receiving RepeaterAuth_Repeater_Manage message the
+*           repeater upstream interface has 100ms to respond with the
+*           RepeaterAuth_Stream_Ready message. Detection of seq_num_M
+*           roll-over is the responsibility of the upstream transmitter.
+******************************************************************************/
+static int XHdcp22Rx_ProcessMessageRepeaterAuthStreamManage(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+
+	/* Log message read completion */
+	XHdcp22Rx_LogWr(InstancePtr,
+		XHDCP22_RX_LOG_EVT_INFO_MESSAGE,
+		XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE);
+
+	/* Check message size */
+	if(InstancePtr->MessageSize != sizeof(XHdcp22_Rx_RepeaterAuthStreamManage))
+	{
+		XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_ERROR,
+			XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE);
+		return XST_FAILURE;
+	}
+
+	/* Record seq_num_M and StreamID_Type parameter */
+	memcpy(InstancePtr->Params.SeqNumM,
+		MsgPtr->RepeaterAuthStreamManage.SeqNumM,
+		XHDCP22_RX_SEQNUMM_SIZE);
+	memcpy(InstancePtr->Params.StreamIdType,
+		MsgPtr->RepeaterAuthStreamManage.StreamIdType,
+		XHDCP22_RX_STREAMID_SIZE);
+
+	/* Run callback function type: XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST */
+	if(InstancePtr->Handles.IsStreamManageRequestCallbackSet)
+	{
+		InstancePtr->Handles.StreamManageRequestCallback(
+			InstancePtr->Handles.StreamManageRequestCallbackRef);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function computes MPrime and sends the RepeaterAuth_Stream_Ready
+* message.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return   XST_SUCCESS.
+*
+* @note     None.
+******************************************************************************/
+static int XHdcp22Rx_SendMessageRepeaterAuthStreamReady(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	XHdcp22_Rx_Message *MsgPtr = (XHdcp22_Rx_Message*)InstancePtr->MessageBuffer;
+	u32 Offset;
+
+	/* Compute MPrime */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_MPRIME);
+	XHdcp22Rx_ComputeMPrime(InstancePtr->Params.StreamIdType, InstancePtr->Params.SeqNumM,
+		InstancePtr->Params.Km, InstancePtr->Params.Rrx, InstancePtr->Params.Rtx,
+		MsgPtr->RepeaterAuthStreamReady.MPrime);
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_MPRIME_DONE);
+
+	/* Generate RepeaterAuth_Stream_Ready message */
+	MsgPtr->RepeaterAuthStreamReady.MsgId = XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMREADY;
+
+	/* Write message to buffer */
+	InstancePtr->Handles.DdcSetAddressCallback(InstancePtr->Handles.DdcSetAddressCallbackRef,
+		XHDCP22_RX_DDC_READ_REG);
+	for(Offset = 0; Offset < sizeof(XHdcp22_Rx_RepeaterAuthStreamReady); Offset++)
+	{
+		InstancePtr->Handles.DdcSetDataCallback(InstancePtr->Handles.DdcSetDataCallbackRef,
+			InstancePtr->MessageBuffer[Offset]);
+	}
+
+	/* Write message size signaling completion */
+	XHdcp22Rx_SetRxStatus(InstancePtr, sizeof(XHdcp22_Rx_RepeaterAuthStreamReady),
+		InstancePtr->Info.ReauthReq, InstancePtr->Info.TopologyReady);
+
+	/* Record MPrime parameter */
+	memcpy(InstancePtr->Params.MPrime, MsgPtr->RepeaterAuthStreamReady.MPrime, XHDCP22_RX_MPRIME_SIZE);
+
+	/* Log message write completion */
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_INFO_MESSAGE, XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMREADY);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function sets DEPTH in the repeater topology table.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    Depth is the Repeater cascade depth. This value gives the
+*           number of attached levels through the connection topology.
+*           The depth cannot cannot exceed 4 levels.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+static void XHdcp22Rx_SetTopologyDepth(XHdcp22_Rx *InstancePtr, u8 Depth)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Depth <= XHDCP22_RX_MAX_DEPTH);
+
+	InstancePtr->Topology.Depth = Depth;
+}
+
+/*****************************************************************************/
+/**
+* This function sets DEVICE_COUNT in the repeater topology table.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    DeviceCnt is the Total number of connected downstream devices.
+*           Always zero for HDCP Receivers. The device count does not include
+*           the HDCP Repeater itself, but only devices downstream from the
+*           HDCP Repeater. The device count cannot exceed 31 devices.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+static void XHdcp22Rx_SetTopologyDeviceCnt(XHdcp22_Rx *InstancePtr, u8 DeviceCnt)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(DeviceCnt > 0);
+	Xil_AssertVoid(DeviceCnt <= XHDCP22_RX_MAX_DEVICE_COUNT);
+
+	InstancePtr->Topology.DeviceCnt = DeviceCnt;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the MAX_DEVS_EXCEEDED error flag in the repeater
+* topology table used to indicate a topology error. Setting the flag
+* indicates that more than 31 downstream devices are attached.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    Value is either TRUE or FALSE.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+static void XHdcp22Rx_SetTopologyMaxDevsExceeded(XHdcp22_Rx *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Value == FALSE || Value == TRUE);
+
+	InstancePtr->Topology.MaxDevsExceeded = Value;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the MAX_CASCADE_EXCEEDED flag in the repeater
+* topology table used to indicate a topology error. Setting the error
+* flag indicates that more than four levels of repeaters have been
+* cascaded together.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    Value is either TRUE or FALSE.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+static void XHdcp22Rx_SetTopologyMaxCascadeExceeded(XHdcp22_Rx *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Value == FALSE || Value == TRUE);
+
+	InstancePtr->Topology.MaxCascadeExceeded = Value;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the HDCP2_LEGACY_DEVICE_DOWNSTREAM flag in the repeater
+* topology table used to indicate the presence of an HDCP2.0-compliant
+* Device in the topology.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    Value is either TRUE or FALSE.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+static void XHdcp22Rx_SetTopologyHdcp2LegacyDeviceDownstream(XHdcp22_Rx *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Value == FALSE || Value == TRUE);
+
+	InstancePtr->Topology.Hdcp2LegacyDeviceDownstream = Value;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the HDCP1_DEVICE_DOWNSTREAM flag in the repeater
+* topology table used to indicate the presence of an HDCP1.x-compliant
+* device in the topology.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param    Value is either TRUE or FALSE.
+*
+* @return   None.
+*
+* @note     None.
+******************************************************************************/
+static void XHdcp22Rx_SetTopologyHdcp1DeviceDownstream(XHdcp22_Rx *InstancePtr, u8 Value)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Value == FALSE || Value == TRUE);
+
+	InstancePtr->Topology.Hdcp1DeviceDownstream = Value;
+}
+
+/*****************************************************************************/
+/**
+* This function clears the log pointers.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	Verbose allows to add debug logging.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_LogReset(XHdcp22_Rx *InstancePtr, u8 Verbose)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Log.Head = 0;
+	InstancePtr->Log.Tail = 0;
+	InstancePtr->Log.Verbose = Verbose;
+
+	/* Reset and start the logging timer. */
+	/* Note: This timer increments continuously and will wrap at 42 second (100 Mhz clock) */
+	if (InstancePtr->TimerInst.IsReady == XIL_COMPONENT_IS_READY) {
+	  XTmrCtr_Reset(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_0);
+	  XTmrCtr_Start(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_0);
+	}
+}
+
+
+/*****************************************************************************/
+/**
+* This function returns the time expired since a log reset was called.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return The expired logging time in useconds.
+*
+* @note   None.
+******************************************************************************/
+u32 XHdcp22Rx_LogGetTimeUSecs(XHdcp22_Rx *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	u32 PeriodUsec = InstancePtr->TimerInst.Config.SysClockFreqHz / 1000000;
+	return (XTmrCtr_GetValue(&InstancePtr->TimerInst, XHDCP22_RX_TMR_CTR_0) / PeriodUsec);
+}
+
+
+/*****************************************************************************/
+/**
+* This function writes HDCP22-RX log event into buffer. If the log event
+* is of type error, the sticky error flag is set. The sticky error flag
+* is used to keep history of error conditions.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	Evt specifies an action to be carried out.
+* @param	Data specifies the information that gets written into log
+*			buffer.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_LogWr(XHdcp22_Rx *InstancePtr, u16 Evt, u16 Data)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Evt < XHDCP22_RX_LOG_EVT_INVALID);
+
+	/* When logging a debug event check if verbose is set to true */
+	if ((InstancePtr->Log.Verbose == FALSE) &&
+			((Evt == XHDCP22_RX_LOG_EVT_DEBUG) ||
+			 (Evt == XHDCP22_RX_LOG_EVT_INFO_MESSAGE))) {
+		return;
+	}
+
+	/* Write data and event into log buffer */
+	InstancePtr->Log.LogItems[InstancePtr->Log.Head].Data = Data;
+	InstancePtr->Log.LogItems[InstancePtr->Log.Head].LogEvent = Evt;
+	InstancePtr->Log.LogItems[InstancePtr->Log.Head].TimeStamp =
+			XHdcp22Rx_LogGetTimeUSecs(InstancePtr);
+
+	/* Update head pointer if reached to end of the buffer */
+	if (InstancePtr->Log.Head == XHDCP22_RX_LOG_BUFFER_SIZE - 1) {
+		/* Clear pointer */
+		InstancePtr->Log.Head = 0;
+	} else {
+		/* Increment pointer */
+		InstancePtr->Log.Head++;
+	}
+
+	/* Check tail pointer. When the two pointer are equal, then the buffer
+	* is full.In this case then increment the tail pointer as well to
+	* remove the oldest entry from the buffer.
+	*/
+	if (InstancePtr->Log.Tail == InstancePtr->Log.Head) {
+		if (InstancePtr->Log.Tail == XHDCP22_RX_LOG_BUFFER_SIZE - 1) {
+			InstancePtr->Log.Tail = 0;
+		} else {
+			InstancePtr->Log.Tail++;
+		}
+	}
+
+	/* Update sticky error flag */
+	if(Evt == XHDCP22_RX_LOG_EVT_ERROR)
+	{
+		InstancePtr->Info.ErrorFlagSticky |= (u32)Data;
+	}
+}
+
+
+/*****************************************************************************/
+/**
+* This function provides the log information from the log buffer.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return
+*           - Content of log buffer if log pointers are not equal.
+*           - Otherwise Zero.
+*
+* @note		None.
+******************************************************************************/
+XHdcp22_Rx_LogItem* XHdcp22Rx_LogRd(XHdcp22_Rx *InstancePtr)
+{
+	XHdcp22_Rx_LogItem* LogPtr;
+	u8 Tail = 0;
+	u8 Head = 0;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	Tail = InstancePtr->Log.Tail;
+	Head = InstancePtr->Log.Head;
+
+	/* Check if there is any data in the log and return a NONE defined log item */
+	if (Tail == Head) {
+		LogPtr = &InstancePtr->Log.LogItems[Tail];
+		LogPtr->Data = 0;
+		LogPtr->LogEvent = XHDCP22_RX_LOG_EVT_NONE;
+		LogPtr->TimeStamp = 0;
+		return LogPtr;
+	}
+
+	LogPtr = &InstancePtr->Log.LogItems[Tail];
+
+	/* Increment tail pointer */
+	if (Tail == XHDCP22_RX_LOG_BUFFER_SIZE - 1) {
+		InstancePtr->Log.Tail = 0;
+	}
+	else {
+		InstancePtr->Log.Tail++;
+	}
+	return LogPtr;
+}
+
+
+/*****************************************************************************/
+/**
+* This function prints the contents of the log buffer.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+* @param	buff is a pointer to the buffer to write to.
+* @param	buff_size is the size of the passed buffer
+*
+* @return	Number of characters printed to the buffer.
+*
+* @note		None.
+******************************************************************************/
+int XHdcp22Rx_LogShow(XHdcp22_Rx *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+	XHdcp22_Rx_LogItem* LogPtr;
+	char str[255];
+	u32 TimeStampPrev = 0;
+
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	strSize = scnprintf(buff+strSize, buff_size-strSize,
+			"\r\n-------HDCP22 RX log start-------\r\n");
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"[Time(us):Delta(us)] <Event>\n\r");
+	strcpy(str, "UNDEFINED");
+	do {
+		/* Read log data */
+		LogPtr = XHdcp22Rx_LogRd(InstancePtr);
+
+		/* Print timestamp */
+		if(LogPtr->LogEvent != XHDCP22_RX_LOG_EVT_NONE)
+		{
+			if(LogPtr->TimeStamp < TimeStampPrev) TimeStampPrev = 0;
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"[%8u:", LogPtr->TimeStamp);
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"%8u] ", (LogPtr->TimeStamp - TimeStampPrev));
+			TimeStampPrev = LogPtr->TimeStamp;
+		}
+
+		/* Print log event */
+		switch(LogPtr->LogEvent) {
+		case(XHDCP22_RX_LOG_EVT_NONE):
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"-------HDCP22 RX log end-------\r\n\r\n");
+			break;
+		case XHDCP22_RX_LOG_EVT_INFO:
+			switch(LogPtr->Data)
+			{
+			/* Print General Log Data */
+			case XHDCP22_RX_LOG_INFO_RESET:
+				strcpy(str, "Asserted [RESET]"); break;
+			case XHDCP22_RX_LOG_INFO_ENABLE:
+				strcpy(str, "State machine [ENABLED]"); break;
+			case XHDCP22_RX_LOG_INFO_DISABLE:
+				strcpy(str, "State machine [DISABLED]"); break;
+			case XHDCP22_RX_LOG_INFO_REQAUTH_REQ:
+				strcpy(str, "Asserted [REAUTH_REQ]"); break;
+			case XHDCP22_RX_LOG_INFO_ENCRYPTION_ENABLE:
+				strcpy(str, "Asserted [ENCRYPTION_ENABLE]"); break;
+			case XHDCP22_RX_LOG_INFO_TOPOLOGY_UPDATE:
+				strcpy(str, "Asserted [TOPOLOGY_UPDATE]"); break;
+			default:
+				strcpy(str, "Unknown?"); break;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"%s\r\n", str);
+			break;
+		case XHDCP22_RX_LOG_EVT_INFO_STATE:
+			switch(LogPtr->Data)
+			{
+			/* Print State Log Data */
+			case XHDCP22_RX_STATE_B0_WAIT_AKEINIT:
+				strcpy(str, "B0_WAIT_AKEINIT"); break;
+			case XHDCP22_RX_STATE_B1_SEND_AKESENDCERT:
+				strcpy(str, "B1_SEND_AKESENDCERT"); break;
+			case XHDCP22_RX_STATE_B1_WAIT_AKEKM:
+				strcpy(str, "B1_WAIT_AKEKM"); break;
+			case XHDCP22_RX_STATE_B1_SEND_AKESENDHPRIME:
+				strcpy(str, "B1_SEND_AKESENDHPRIME"); break;
+			case XHDCP22_RX_STATE_B1_SEND_AKESENDPAIRINGINFO:
+				strcpy(str, "B1_SEND_AKESENDPAIRINGINFO"); break;
+			case XHDCP22_RX_STATE_B1_WAIT_LCINIT:
+				strcpy(str, "B1_WAIT_LCINIT"); break;
+			case XHDCP22_RX_STATE_B2_SEND_LCSENDLPRIME:
+				strcpy(str, "B2_SEND_LCSENDLPRIME"); break;
+			case XHDCP22_RX_STATE_B2_WAIT_SKESENDEKS:
+				strcpy(str, "B2_WAIT_SKESENDEKS"); break;
+			case XHDCP22_RX_STATE_B3_COMPUTE_KS:
+				strcpy(str, "B3_COMPUTE_KS"); break;
+			case XHDCP22_RX_STATE_B4_AUTHENTICATED:
+				strcpy(str, "B4_AUTHENTICATED"); break;
+			case XHDCP22_RX_STATE_C4_WAIT_FOR_DOWNSTREAM:
+				strcpy(str, "C4_WAIT_FOR_DOWNSTREAM"); break;
+			case XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST:
+				strcpy(str, "C5_SEND_RECEIVERIDLIST"); break;
+			case XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST_DONE:
+				strcpy(str, "C5_SEND_RECEIVERIDLIST_DONE"); break;
+			case XHDCP22_RX_STATE_C6_VERIFY_RECEIVERIDLISTACK:
+				strcpy(str, "C6_WAIT_RECEIVERIDLISTACK"); break;
+			case XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT:
+				strcpy(str, "C7_WAIT_STREAMMANAGEMENT"); break;
+			case XHDCP22_RX_STATE_C7_SEND_STREAM_READY:
+				strcpy(str, "C7_SEND_STREAM_READY"); break;
+			case XHDCP22_RX_STATE_C7_SEND_STREAM_READY_DONE:
+				strcpy(str, "C7_SEND_STREAM_READY_DONE"); break;
+			case XHDCP22_RX_STATE_C8_AUTHENTICATED:
+				strcpy(str, "C8_AUTHENTICATED"); break;
+			default:
+				strcpy(str, "Unknown?"); break;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Current state [%s]\r\n", str);
+			break;
+		case XHDCP22_RX_LOG_EVT_INFO_MESSAGE:
+			switch(LogPtr->Data)
+			{
+			/* Print Message Log Data */
+			case XHDCP22_RX_MSG_ID_AKEINIT:
+				strcpy(str, "Received message [AKEINIT]"); break;
+			case XHDCP22_RX_MSG_ID_AKESENDCERT:
+				strcpy(str, "Sent message [AKESENDCERT]"); break;
+			case XHDCP22_RX_MSG_ID_AKENOSTOREDKM:
+				strcpy(str, "Received message [AKENOSTOREDKM]"); break;
+			case XHDCP22_RX_MSG_ID_AKESTOREDKM:
+				strcpy(str, "Received message [AKESTOREDKM]"); break;
+			case XHDCP22_RX_MSG_ID_AKESENDHPRIME:
+				strcpy(str, "Sent message [AKESENDHPRIME]"); break;
+			case XHDCP22_RX_MSG_ID_AKESENDPAIRINGINFO:
+				strcpy(str, "Sent message [AKESENDPAIRINGINFO]"); break;
+			case XHDCP22_RX_MSG_ID_LCINIT:
+				strcpy(str, "Received message [LCINIT]"); break;
+			case XHDCP22_RX_MSG_ID_LCSENDLPRIME:
+				strcpy(str, "Sent message [LCSENDLPRIME]"); break;
+			case XHDCP22_RX_MSG_ID_SKESENDEKS:
+				strcpy(str, "Received message [SKESENDEKS]"); break;
+			case XHDCP22_RX_MSG_ID_REPEATERAUTHSENDRXIDLIST:
+				strcpy(str, "Sent message [REPEATERAUTHSENDRXIDLIST]"); break;
+			case XHDCP22_RX_MSG_ID_REPEATERAUTHSENDACK:
+				strcpy(str, "Received message [REPEATERAUTHSENDACK]"); break;
+			case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE:
+				strcpy(str, "Received message [REPEATERAUTHSTREAMMANAGE]"); break;
+			case XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMREADY:
+				strcpy(str, "Sent message [REPEATERAUTHSTREAMREADY]"); break;
+			default:
+				strcpy(str, "Unknown?"); break;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"%s\r\n", str);
+			break;
+		case XHDCP22_RX_LOG_EVT_DEBUG:
+			switch(LogPtr->Data)
+			{
+			/* Print Debug Log Data */
+			case XHDCP22_RX_LOG_DEBUG_WRITE_MESSAGE_AVAILABLE:
+				strcpy(str, "Write message available"); break;
+			case XHDCP22_RX_LOG_DEBUG_READ_MESSAGE_COMPLETE:
+				strcpy(str, "Read message complete"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_RSA:
+				strcpy(str, "COMPUTE_RSA"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_RSA_DONE:
+				strcpy(str, "COMPUTE_RSA_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_KM:
+				strcpy(str, "COMPUTE_KM"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_KM_DONE:
+				strcpy(str, "COMPUTE_KM_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_HPRIME:
+				strcpy(str, "COMPUTE_HPRIME"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_HPRIME_DONE:
+				strcpy(str, "COMPUTE_HPRIME_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_EKH:
+				strcpy(str, "COMPUTE_EKHKM"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_EKH_DONE:
+				strcpy(str, "COMPUTE_EKHKM_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_LPRIME:
+				strcpy(str, "COMPUTE_LPRIME"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_LPRIME_DONE:
+				strcpy(str, "COMPUTE_LPRIME_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_KS:
+				strcpy(str, "COMPUTE_KS"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_KS_DONE:
+				strcpy(str, "COMPUTE_KS_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_VPRIME:
+				strcpy(str, "COMPUTE_VPRIME"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_VPRIME_DONE:
+				strcpy(str, "COMPUTE_VPRIME_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_MPRIME:
+				strcpy(str, "COMPUTE_MPRIME"); break;
+			case XHDCP22_RX_LOG_DEBUG_COMPUTE_MPRIME_DONE:
+				strcpy(str, "COMPUTE_MPRIME_DONE"); break;
+			case XHDCP22_RX_LOG_DEBUG_TIMER_START:
+				strcpy(str, "TIMER_START"); break;
+			case XHDCP22_RX_LOG_DEBUG_TIMER_EXPIRED:
+				strcpy(str, "TIMER_EXPIRED"); break;
+			default:
+				strcpy(str, "Unknown?"); break;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Debug: Event [%s]\r\n", str);
+			break;
+		case XHDCP22_RX_LOG_EVT_ERROR:
+			switch(LogPtr->Data)
+			{
+			/* Print Error Log Data */
+			case XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE:
+				strcpy(str, "Received message with unexpected size"); break;
+			case XHDCP22_RX_ERROR_FLAG_FORCE_RESET:
+				strcpy(str, "Forcing reset after error"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT:
+				strcpy(str, "Problem processing received message [AKEINIT]"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_AKENOSTOREDKM:
+				strcpy(str, "Problem processing received message [AKENOSTOREDKM]"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_AKESTOREDKM:
+				strcpy(str, "Problem processing received message [AKESTOREDKM]"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_LCINIT:
+				strcpy(str, "Problem processing received message [LCINIT]"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_SKESENDEKS:
+				strcpy(str, "Problem processing received message [SKESENDEKS]"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_REPEATERAUTHSENDACK:
+				strcpy(str, "Problem processing received message [REPEATERAUTHSENDACK]"); break;
+			case XHDCP22_RX_ERROR_FLAG_PROCESSING_REPEATERAUTHSTREAMMANAGE:
+				strcpy(str, "Problem processing received message [REPEATERAUTHSTREAMMANAGE]"); break;
+			case XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY:
+				strcpy(str, "Detected problem with link integrity"); break;
+			case XHDCP22_RX_ERROR_FLAG_DDC_BURST:
+				strcpy(str, "Detected problem with DDC burst read/write"); break;
+			case XHDCP22_RX_ERROR_FLAG_MAX_LCINIT_ATTEMPTS:
+				strcpy(str, "Exceeded maximum LCINIT attempts"); break;
+			case XHDCP22_RX_ERROR_FLAG_EMPTY_REPEATER_TOPOLOGY:
+				strcpy(str, "Empty repeater topology, device count is zero"); break;
+			case XHDCP22_RX_ERROR_FLAG_MAX_REPEATER_TOPOLOGY:
+				strcpy(str, "Exceeded repeater topology maximums"); break;
+			default:
+				strcpy(str, "Unknown?"); break;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: %s\r\n", str);
+			break;
+		case XHDCP22_RX_LOG_EVT_USER:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"User: %d\r\n", LogPtr->Data);
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Unknown log event\r\n");
+			break;
+		}
+	} while (LogPtr->LogEvent != XHDCP22_RX_LOG_EVT_NONE);
+	return strSize;
+}
+
+/*****************************************************************************/
+/**
+* This function prints the state machine information.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Rx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Rx_Info(XHdcp22_Rx *InstancePtr)
+{
+	XDEBUG_PRINTF("Status: ");
+	if (XHdcp22Rx_IsEnabled(InstancePtr)) {
+		switch (InstancePtr->Info.AuthenticationStatus) {
+			case XHDCP22_RX_UNAUTHENTICATED :
+				XDEBUG_PRINTF("Not Authenticated.\n\r");
+			break;
+
+			case XHDCP22_RX_AUTHENTICATION_BUSY :
+				XDEBUG_PRINTF("Authentication Busy.\n\r");
+			break;
+
+			case XHDCP22_RX_AUTHENTICATED :
+				XDEBUG_PRINTF("Authenticated.\n\r");
+			break;
+
+			case XHDCP22_RX_REAUTHENTICATE_REQUESTED :
+				XDEBUG_PRINTF("Reauthentication Requested.\n\r");
+			break;
+
+			default :
+				XDEBUG_PRINTF("Unknown?\n\r");
+			break;
+		}
+	} else {
+		XDEBUG_PRINTF("Core is disabled.\n\r");
+	}
+
+	XDEBUG_PRINTF("Encryption: ");
+	if (XHdcp22Rx_IsEncryptionEnabled(InstancePtr)) {
+		XDEBUG_PRINTF("Enabled.\n\r");
+	} else {
+		XDEBUG_PRINTF("Disabled.\n\r");
+	}
+
+	XDEBUG_PRINTF("Repeater: ");
+	if (XHdcp22Rx_IsRepeater(InstancePtr)) {
+		if (InstancePtr->Topology.MaxDevsExceeded)
+			XDEBUG_PRINTF("MaxDevsExceeded, ");
+
+		if (InstancePtr->Topology.MaxCascadeExceeded)
+			XDEBUG_PRINTF("MaxCascadeExceeded, ");
+
+		if (InstancePtr->Topology.Hdcp2LegacyDeviceDownstream)
+			XDEBUG_PRINTF("Hdcp2LegacyDeviceDownstream, ");
+
+		if (InstancePtr->Topology.Hdcp1DeviceDownstream)
+			XDEBUG_PRINTF("Hdcp1DeviceDownstream, ");
+
+		XDEBUG_PRINTF("Depth=%d, ", InstancePtr->Topology.Depth);
+		XDEBUG_PRINTF("DeviceCnt=%d, ", InstancePtr->Topology.DeviceCnt);
+		XDEBUG_PRINTF("StreamType=%d\n\r", XHdcp22Rx_GetContentStreamType(InstancePtr));
+	} else {
+		XDEBUG_PRINTF("Disabled.\n\r");
+	}
+
+	XDEBUG_PRINTF("Auth Requests: %d\n\r", InstancePtr->Info.AuthRequestCnt);
+	XDEBUG_PRINTF("Reauth Requests: %d\n\r", InstancePtr->Info.ReauthRequestCnt);
+	XDEBUG_PRINTF("Link Errors: %d\n\r", InstancePtr->Info.LinkErrorCnt);
+	XDEBUG_PRINTF("DDC Errors: %d\n\r", InstancePtr->Info.DdcErrorCnt);
+}
+
+/*****************************************************************************/
+/**
+* This function is a stub for the run handler. The stub is here in
+* case the upper layer forgot to set the handlers. On initialization, all
+* handlers are set to this callback. It is considered an error for this
+* handler to be invoked.
+*
+* @param	HandlerRef is a callback reference passed in by the upper
+*			layer when setting the callback functions, and passed back to
+*			the upper layer when the callback is invoked.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+static void XHdcp22_Rx_StubRunHandler(void *HandlerRef)
+{
+	Xil_AssertVoid(HandlerRef != NULL);
+	Xil_AssertVoidAlways();
+}
+
+/*****************************************************************************/
+/**
+* This function is a stub for the set handler. The stub is here in
+* case the upper layer forgot to set the handlers. On initialization, all
+* handlers are set to this callback. It is considered an error for this
+* handler to be invoked.
+*
+* @param	HandlerRef is a callback reference passed in by the upper
+*			layer when setting the callback functions, and passed back to
+*			the upper layer when the callback is invoked.
+* @param	Data is a value to be set.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+static void XHdcp22_Rx_StubSetHandler(void *HandlerRef, u32 Data)
+{
+	Xil_AssertVoid(HandlerRef != NULL);
+	Xil_AssertVoid(Data != 0);
+	Xil_AssertVoidAlways();
+}
+
+/*****************************************************************************/
+/**
+* This function is a stub for the set handler. The stub is here in
+* case the upper layer forgot to set the handlers. On initialization, all
+* handlers are set to this callback. It is considered an error for this
+* handler to be invoked.
+*
+* @param	HandlerRef is a callback reference passed in by the upper
+*			layer when setting the callback functions, and passed back to
+*			the upper layer when the callback is invoked.
+*
+* @return	Returns the get value.
+*
+* @note		None.
+******************************************************************************/
+static u32 XHdcp22_Rx_StubGetHandler(void *HandlerRef)
+{
+	Xil_AssertNonvoid(HandlerRef != NULL);
+	Xil_AssertNonvoidAlways();
+
+	return 0;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx.h
@@ -0,0 +1,667 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file xhdcp22_rx.h
+* @{
+* @details
+*
+* This is the main header file for the Xilinx HDCP 2.2 Receiver device
+* driver. The HDCP 2.2 Receiver driver implements the authentication
+* state machine.
+* It consists of:
+* - A state machine handling the states as specified in the HDCP revision 2.2
+*   specification.
+* - Message handling from/to the HDCP 2.2 transmitter.
+* - Logging functionality including time stamps.
+*
+* <b>Software Initialization and Configuration</b>
+*
+* The application needs to do the following steps to run the Receiver.
+* - Call XHdcp22Rx_LookupConfig using the device ID to find the
+*   core configuration instance.
+* - Call XHdcp22Rx_CfgInitialize to intitialize the device instance.
+* - Call XHdcp22Rx_SetCallback to set the pointers to the callback
+*   functions defined by the enumerated type XHdcp22_Rx_HandlerType.
+* - Call XHdcp22Rx_LoadPublicCert to load the DCP public certificate.
+* - Call XHdcp22Rx_LoadPrivateKey to load the RSA private key.
+* - Call XHdcp22Rx_LoadLc128 to load the DCP global constant.
+* - Call XHdcp22Rx_LogReset to reset the log buffer.
+* - The following functions should be called in the interfacing
+*   protocol driver (i.e. HDMI) to set event flags:
+*   - XHdcp22Rx_SetLinkError
+*   - XHdcp22Rx_SetDdcError
+*   - XHdcp22Rx_SetWriteMessageAvailable
+*   - XHdcp22Rx_SetReadMessageComplete
+* - Call XHdcp22Rx_Enable to enable the state machine.
+* - Call XHdcp22Rx_Poll to run the Receiver state machine. The
+*   call to this function is non-blocking and should be called
+*   repeatedly in a spin loop as long as the receiver is active.
+*
+* <b>Interrupts</b>
+*
+* None.
+*
+* <b> Threads </b>
+*
+* This driver is not thread safe. Any needs for threads or thread mutual
+* exclusion must be satisfied by the layer above this driver.
+*
+* <b> Asserts </b>
+*
+* Asserts are used within all Xilinx drivers to enforce constraints on argument
+* values. Asserts can be turned off on a system-wide basis by defining at
+* compile time, the NDEBUG identifier. By default, asserts are turned on and it
+* is recommended that users leave asserts on during development.
+*
+* <b> Building the driver </b>
+*
+* The HDCP TX driver is composed of several source files. This allows the user
+* to build and link only those parts of the driver that are necessary.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+* 1.01  MH   01/15/16 Added XHdcp22Rx_SetDdcReauthReq to function prototypes.
+*                     Replaced function XHdcp22Rx_SetDdcHandles with
+*                     XHdcp22Rx_SetCallback.
+* 1.02  MH   03/02/16 Updated to change NPrimeP and NPrimeQ from pointer
+*                     to array. Added function XHDCP22Rx_GetVersion.
+* 2.00  MH   04/14/16 Updated for repeater upstream support.
+* 2.01  MH   02/28/17 Fixed compiler warnings.
+*</pre>
+*
+*****************************************************************************/
+
+#ifndef XHDCP22_RX_H		/* prevent circular inclusions */
+#define XHDCP22_RX_H		/* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files ********************************/
+#include "xil_types.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xdebug.h"
+#include "xtmrctr.h"
+#include "xhdcp22_rng.h"
+#include "xhdcp22_mmult.h"
+#include "xhdcp22_cipher.h"
+
+/************************** Constant Definitions ****************************/
+#define XHDCP22_RX_MAX_MESSAGE_SIZE           534  /**< Maximum message size */
+#define XHDCP22_RX_LOG_BUFFER_SIZE            256  /**< The size of the log buffer */
+#define XHDCP22_RX_ENCRYPTION_STATUS_INTERVAL 1000 /**< 1sec encryption status check interval */
+#define XHDCP22_RX_REPEATERAUTH_ACK_INTERVAL  2000 /**< 2sec RepeaterAuth Ack interval */
+
+/************************** Variable Declaration ****************************/
+
+/**************************** Type Definitions ******************************/
+/** Type for pointer to state function */
+typedef void *(*XHdcp22_Rx_StateFunc)(void *InstancePtr);
+/** Type for pointer to single input function */
+typedef void (*XHdcp22_Rx_RunHandler)(void *HandlerRef);
+/** Type for pointer to two input function */
+typedef void (*XHdcp22_Rx_SetHandler)(void *HandlerRef, u32 Data);
+/** Type for pointer to single input function with a return value */
+typedef u32  (*XHdcp22_Rx_GetHandler)(void *HandlerRef);
+
+/**
+ * These constants are used to define the protocol.
+ */
+typedef enum
+{
+	XHDCP22_RX_HDMI, /**< HDCP22 over HDMI */
+	XHDCP22_RX_DP    /**< HDCP22 over DP, Not yet supported */
+} XHdcp22_Rx_Protocol;
+
+/**
+ * These constants are used to define the mode.
+ */
+typedef enum
+{
+	XHDCP22_RX_RECEIVER,  /**< HDCP22 receiver */
+	XHDCP22_RX_REPEATER,  /**< HDCP22 repeater upstream interface */
+	XHDCP22_RX_CONVERTER  /**< HDCP22 converter upstream interface */
+} XHdcp22_Rx_Mode;
+
+/**
+ * These constants are used to identify callback functions.
+ */
+typedef enum
+{
+	XHDCP22_RX_HANDLER_UNDEFINED,             /**< Undefined */
+	XHDCP22_RX_HANDLER_DDC_SETREGADDR,        /**< Set the DDC register address */
+	XHDCP22_RX_HANDLER_DDC_SETREGDATA,        /**< Set the DDC register data */
+	XHDCP22_RX_HANDLER_DDC_GETREGDATA,        /**< Get the DDC register data */
+	XHDCP22_RX_HANDLER_DDC_GETWBUFSIZE,       /**< Get the DDC the write buffer size */
+	XHDCP22_RX_HANDLER_DDC_GETRBUFSIZE,       /**< Get the DDC the read buffer size */
+	XHDCP22_RX_HANDLER_DDC_ISWBUFEMPTY,       /**< Check if the DDC write buffer is empty */
+	XHDCP22_RX_HANDLER_DDC_ISRBUFEMPTY,       /**< Check if the DDC read buffer is empty */
+	XHDCP22_RX_HANDLER_DDC_CLEARRBUF,         /**< Clear the DDC read buffer */
+	XHDCP22_RX_HANDLER_DDC_CLEARWBUF,         /**< Clear the DDC write buffer */
+	XHDCP22_RX_HANDLER_AUTHENTICATED,         /**< Executed when state machine transitions to authenticated */
+	XHDCP22_RX_HANDLER_UNAUTHENTICATED,       /**< Executed when state machine transitions to unauthenticated */
+	XHDCP22_RX_HANDLER_AUTHENTICATION_REQUEST,/**< Executed when authentication request is received */
+	XHDCP22_RX_HANDLER_TOPOLOGY_UPDATE,       /**< Executed when state machine is ready for the topology update. */
+	XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST, /**< Executed when stream management request is received. */
+	XHDCP22_RX_HANDLER_ENCRYPTION_UPDATE,     /**< Executed when encryption status update. */
+	XHDCP22_RX_HANDLER_INVALID                /**< Invalid */
+} XHdcp22_Rx_HandlerType;
+
+/**
+ * These constants are the authentication and key exchange states.
+ */
+typedef enum
+{
+	XHDCP22_RX_STATE_UNDEFINED                    = 0x000,  /**< Undefined */
+	XHDCP22_RX_STATE_B0_WAIT_AKEINIT              = 0xB00,  /**< Unauthenticated */
+	XHDCP22_RX_STATE_B1_SEND_AKESENDCERT          = 0xB10,  /**< Compute Km: Send AKE_Send_Cert */
+	XHDCP22_RX_STATE_B1_WAIT_AKEKM                = 0xB11,  /**< Compute Km: Wait for AKE_No_Stored_km or AKE_Stored_km */
+	XHDCP22_RX_STATE_B1_SEND_AKESENDHPRIME        = 0xB12,  /**< Compute Km: Send AKE_Send_H_prime */
+	XHDCP22_RX_STATE_B1_SEND_AKESENDPAIRINGINFO   = 0xB13,  /**< Compute Km: Send AKE_Send_Pairing_Info */
+	XHDCP22_RX_STATE_B1_WAIT_LCINIT               = 0xB14,  /**< Compute Km: Wait for LCInit */
+	XHDCP22_RX_STATE_B2_SEND_LCSENDLPRIME         = 0xB20,  /**< Compute L': Send LC_Send_L_prime */
+	XHDCP22_RX_STATE_B2_WAIT_SKESENDEKS           = 0xB21,  /**< Compute L': Wait for SKE_Send_Eks */
+	XHDCP22_RX_STATE_B3_COMPUTE_KS                = 0xB30,  /**< Compute Ks */
+	XHDCP22_RX_STATE_B4_AUTHENTICATED             = 0xB40,  /**< Receiver Authenticated */
+	XHDCP22_RX_STATE_C4_WAIT_FOR_DOWNSTREAM       = 0xC40,  /**< Wait for Downstream */
+	XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST       = 0xC50,  /**< Assemble Receiver ID List: Send RepeaterAuth_Send_ReceiverID_List */
+	XHDCP22_RX_STATE_C5_SEND_RECEIVERIDLIST_DONE  = 0xC51,  /**< Assemble Receiver ID List: Send RepeaterAuth_Send_ReceiverID_List Done */
+	XHDCP22_RX_STATE_C6_VERIFY_RECEIVERIDLISTACK  = 0xC60,  /**< Verify Receiver ID List Acknowledgement*/
+	XHDCP22_RX_STATE_C7_WAIT_STREAM_MANAGEMENT    = 0xC70,  /**< Content Stream Management: Wait for RepeaterAuth_Stream_Manage */
+	XHDCP22_RX_STATE_C7_SEND_STREAM_READY         = 0xC71,  /**< Content Stream Management: Send RepeaterAuth_Stream_Ready */
+	XHDCP22_RX_STATE_C7_SEND_STREAM_READY_DONE    = 0xC72,  /**< Content Stream Management: Send RepeaterAuth_Stream_Ready Done */
+	XHDCP22_RX_STATE_C8_AUTHENTICATED             = 0xC80,  /**< Repeater Authenticated */
+	XHDCP22_RX_STATE_INVALID                                /**< Invalid */
+} XHdcp22_Rx_StateType;
+
+/**
+ * These constants define the authentication status.
+ */
+typedef enum
+{
+	XHDCP22_RX_UNAUTHENTICATED,         /**< Unauthenticated */
+	XHDCP22_RX_AUTHENTICATION_BUSY,     /**< Authentication Busy */
+	XHDCP22_RX_AUTHENTICATED,           /**< Authenticated */
+	XHDCP22_RX_REAUTHENTICATE_REQUESTED /**< Reauthentication requested */
+} XHdcp22_Rx_AuthenticationType;
+
+/**
+* These constants are the general logging events.
+*/
+typedef enum {
+	XHDCP22_RX_LOG_EVT_NONE,          /** Log Event None */
+	XHDCP22_RX_LOG_EVT_INFO,          /** Log General Info Event */
+	XHDCP22_RX_LOG_EVT_INFO_STATE,    /** Log State Info Event */
+	XHDCP22_RX_LOG_EVT_INFO_MESSAGE,  /** Log Messsage Info Event */
+	XHDCP22_RX_LOG_EVT_DEBUG,         /** Log Debug Event */
+	XHDCP22_RX_LOG_EVT_ERROR,         /** Log Error Event */
+	XHDCP22_RX_LOG_EVT_USER,          /** User logging */
+	XHDCP22_RX_LOG_EVT_INVALID        /** Last value the list, only used for checking */
+} XHdcp22_Rx_LogEvt;
+
+/**
+* These constants are used to identify fields inside the topology structure
+*/
+typedef enum {
+	XHDCP22_RX_TOPOLOGY_DEPTH,
+	XHDCP22_RX_TOPOLOGY_DEVICECNT,
+	XHDCP22_RX_TOPOLOGY_MAXDEVSEXCEEDED,
+	XHDCP22_RX_TOPOLOGY_MAXCASCADEEXCEEDED,
+	XHDCP22_RX_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM,
+	XHDCP22_RX_TOPOLOGY_HDCP1DEVICEDOWNSTREAM,
+	XHDCP22_RX_TOPOLOGY_INVALID
+} XHdcp22_Rx_TopologyField;
+
+/**
+ * This typedef is the test DDC register definition.
+ */
+typedef struct
+{
+	u8 Address;
+	u8 Name[20];
+	int Access;
+	u8 Value;
+} XHdcp22_Rx_TestDdcReg;
+
+/**
+ * This typedef is the test structure used for standalone driver testing.
+ */
+typedef struct
+{
+	int                    TestFlag;
+	int                    TestMode;
+	int                    TestReceiver;
+	int                    State;
+	int                    *NextStateVector;
+	int                    TestReturnCode;
+	u32                    NextStateOffset;
+	u32                    NextStateSize;
+	u32                    NextStateStatus;
+	XHdcp22_Rx_TestDdcReg  DdcRegisterMap[5];
+	u32                    DdcRegisterMapAddress;
+	u32                    DdcRegisterAddress;
+	u8                     WriteMessageBuffer[XHDCP22_RX_MAX_MESSAGE_SIZE];
+	u32                    WriteMessageSize;
+	u32                    WriteMessageOffset;
+	u8                     ReadMessageBuffer[XHDCP22_RX_MAX_MESSAGE_SIZE];
+	u32                    ReadMessageSize;
+	u32                    ReadMessageOffset;
+	u32                    WaitCounter;
+	u8                     Rrx[8];
+	u8                     RxCaps[3];
+	u8                     Verbose;
+} XHdcp22_Rx_Test;
+
+/**
+ * This typedef is used to store handles to function pointers
+ */
+typedef struct
+{
+	/** Function pointer used to set the DDC register address */
+	XHdcp22_Rx_SetHandler DdcSetAddressCallback;
+	/** To be passed to callback function */
+	void                  *DdcSetAddressCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcSetAddressCallbackSet;
+
+	/** Function pointer used to set the DDC register data */
+	XHdcp22_Rx_SetHandler DdcSetDataCallback;
+	/** To be passed to callback function */
+	void                  *DdcSetDataCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcSetDataCallbackSet;
+
+	/** Function pointer used to get the DDC register data */
+	XHdcp22_Rx_GetHandler DdcGetDataCallback;
+	/** To be passed to callback function */
+	void                  *DdcGetDataCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcGetDataCallbackSet;
+
+	/** Function pointer used to get the DDC write buffer size */
+	XHdcp22_Rx_GetHandler DdcGetWriteBufferSizeCallback;
+	/** To be passed to callback function */
+	void                  *DdcGetWriteBufferSizeCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcGetWriteBufferSizeCallbackSet;
+
+	/** Function pointer used to get the DDC read buffer size */
+	XHdcp22_Rx_GetHandler DdcGetReadBufferSizeCallback;
+	/** To be passed to callback function */
+	void                  *DdcGetReadBufferSizeCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcGetReadBufferSizeCallbackRefSet;
+
+	/** Function pointer used to check if the DDC write buffer is empty */
+	XHdcp22_Rx_GetHandler DdcIsWriteBufferEmptyCallback;
+	/** To be passed to callback function */
+	void                  *DdcIsWriteBufferEmptyCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcIsWriteBufferEmptyCallbackSet;
+
+	/** Function pointer used to check if the DDC read buffer is empty */
+	XHdcp22_Rx_GetHandler DdcIsReadBufferEmptyCallback;
+	/** To be passed to callback function */
+	void                  *DdcIsReadBufferEmptyCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcIsReadBufferEmptyCallbackSet;
+
+	/** Function pointer used to clear the DDC read buffer */
+	XHdcp22_Rx_RunHandler DdcClearReadBufferCallback;
+	/** To be passed to callback function */
+	void                  *DdcClearReadBufferCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcClearReadBufferCallbackSet;
+
+	/** Function pointer used to clear the DDC write buffer */
+	XHdcp22_Rx_RunHandler DdcClearWriteBufferCallback;
+	/** To be passed to callback function */
+	void                  *DdcClearWriteBufferCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcClearWriteBufferCallbackSet;
+
+	/** Function pointer used to set auto clear on the DDC RxStatus READY bit*/
+	XHdcp22_Rx_RunHandler DdcClearRepeaterReadyCallback;
+	/** To be passed to callback function */
+	void                  *DdcClearRepeaterReadyCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsDdcClearRepeaterReadyCallbackSet;
+
+	/** This flag is set true when all the DDC callbacks have been registered */
+	u8                    IsDdcAllCallbacksSet;
+
+	/** Function pointer called when statemachine transitions to authenticated */
+	XHdcp22_Rx_RunHandler AuthenticatedCallback;
+	/** To be passed to callback function */
+	void                  *AuthenticatedCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsAuthenticatedCallbackSet;
+
+	/** Function pointer called when statemachine transitions to unauthenticated */
+	XHdcp22_Rx_RunHandler UnauthenticatedCallback;
+	/** To be passed to callback function */
+	void                  *UnauthenticatedCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsUnauthenticatedCallbackSet;
+
+	/** Function pointer called when authentication request message is received */
+	XHdcp22_Rx_RunHandler AuthenticationRequestCallback;
+	/** To be passed to callback function */
+	void                  *AuthenticationRequestCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsAuthenticationRequestCallbackSet;
+
+	/** Function pointer called when stream management message is received */
+	XHdcp22_Rx_RunHandler StreamManageRequestCallback;
+	/** To be passed to callback function */
+	void                  *StreamManageRequestCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsStreamManageRequestCallbackSet;
+
+	/** Function pointer called when repeater is ready to for a topology update */
+	XHdcp22_Rx_RunHandler TopologyUpdateCallback;
+	/** To be passed to callback function */
+	void                  *TopologyUpdateCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsTopologyUpdateCallbackSet;
+
+	/** Function pointer called when encryption status has changed */
+	XHdcp22_Rx_RunHandler EncryptionStatusCallback;
+	/** To be passed to callback function */
+	void                  *EncryptionStatusCallbackRef;
+	/** This flag is set true when the callback has been registered */
+	u8                    IsEncryptionStatusCallbackSet;
+} XHdcp22_Rx_Handles;
+
+/**
+ * This typedef is used to store temporary parameters for computations
+ */
+typedef struct
+{
+	u8 Rtx[8];
+	u8 TxCaps[3];
+	u8 Rrx[8];
+	u8 RxCaps[3];
+	u8 Km[16];
+	u8 Rn[8];
+	u8 HPrime[32];
+	u8 LPrime[32];
+	u8 EKh[16];
+	u8 Riv[8];
+	u8 Ks[16];
+	u8 VPrime[32];
+	u8 SeqNumM[3];
+	u8 StreamIdType[2];
+	u8 MPrime[32];
+} XHdcp22_Rx_Parameters;
+
+/**
+ * This typedef is used to store logging events.
+ */
+typedef struct {
+	/** Event that has been triggered */
+	u16 LogEvent;
+	/** Optional data */
+	u16 Data;
+	/** Timestamp on when event occured. Only used for time critical events */
+	u32 TimeStamp;
+} XHdcp22_Rx_LogItem;
+
+/**
+* This typedef contains the HDCP22 log list.
+*/
+typedef struct {
+	/** Data */
+	XHdcp22_Rx_LogItem LogItems[XHDCP22_RX_LOG_BUFFER_SIZE];
+	/** Tail pointer */
+	u8 Tail;
+	/** Head pointer */
+	u8 Head;
+	/** Logging is extended with debug events. */
+	u8 Verbose;
+} XHdcp22_Rx_Log;
+
+/**
+ * This typedef provides information about status of HDCP-RX authentication.
+ */
+typedef struct
+{
+	/** Flag indicates that device is enabled */
+	u8  IsEnabled;
+	/** Flag indicates that AKE_No_Stored_Km message was received */
+	u8  IsNoStoredKm;
+	/** Number of LC_Init attempts */
+	u16 LCInitAttempts;
+	/** Reauthentication request flag */
+	u8  ReauthReq;
+	/** Topology ready flag */
+	u8  TopologyReady;
+	/** Flag to capture error events that require service */
+	u32 ErrorFlag;
+	/** Flag to capture all error conditions persistently */
+	u32 ErrorFlagSticky;
+	/** Flag to capture DDC events */
+	u32 DdcFlag;
+	/** Expiration flag set when the hardware timer has interrupted. */
+	u8  TimerExpired;
+	/** Keep track of why the timer was started (message or status checking). */
+	u8  TimerReasonId;
+	/** Keep track of the start value of the timer. */
+	u32 TimerInitialTicks;
+	/** Counter for repeater topology upstream propogation */
+	u32 SeqNumV;
+	/** Flag indicated that content stream management info messsage has been processed */
+	u8  HasStreamManagementInfo;
+	/** State machine current state */
+	XHdcp22_Rx_StateType CurrentState;
+	/** State machine next state */
+	XHdcp22_Rx_StateType NextState;
+	/** State machine return state. Used for parallel execution of content stream
+	    management and topology information propagation */
+	XHdcp22_Rx_StateType ReturnState;
+	/** Authentication status */
+	XHdcp22_Rx_AuthenticationType AuthenticationStatus;
+	/** Skip read, indicates that message has been read but not yet processed */
+	u8 SkipRead;
+	/** Flag used to indicate topology change. When set to one, indicates
+	    that the topology table has been updated and is available for
+	    upstream propagation. */
+	u8 IsTopologyValid;
+	/** Flag indicates encryption is enabled */
+	u8 IsEncrypted;
+	/** Authentication request count */
+	u32 AuthRequestCnt;
+	/** Re-authentication request count */
+	u32 ReauthRequestCnt;
+	/** Link error count */
+	u32 LinkErrorCnt;
+	/** Ddc error count */
+	u32 DdcErrorCnt;
+} XHdcp22_Rx_Info;
+
+/**
+ * This typedef is the repeater topology table used to communicate topology
+ * information to the receiver upstream interface.
+ */
+typedef struct
+{
+	/** Receiver ID list of all downstream devices. The list consists of
+	    a contiguous set of bytes stored in big-endian order, with each
+	    Receiver ID occuping five bytes and a total of 31 Receiver IDs. */
+	u8 ReceiverIdList[31][5];
+	/** Repeater cascade depth. This value gives the number of attached
+	    levels through the connection topology with maximum depth of 4. */
+	u8 Depth;
+	/** Total number of connected downstream devices. Always zero for
+	    HDCP Receivers. This count does not include the HDCP Repeater
+	    itself, but only devices downstream from the HDCP Repeater. */
+	u8 DeviceCnt;
+	/** Flag used to indicate topology error. When set to one, more
+	    than 31 downstream devices are attached. */
+	u8 MaxDevsExceeded;
+	/** Flag used to indicate topology error. When set to one, more
+	    than four levels of repeaters have been casaded together. */
+	u8 MaxCascadeExceeded;
+	/** Flag used to indicate topology information. When set to one,
+	    indicates presence of an HDCP2.1-compliant Device in the topology. */
+	u8 Hdcp2LegacyDeviceDownstream;
+	/** Flag used to indicate topology information. When set to one,
+	    indicates precense of an HDCP1.x-compliant device in the topology. */
+	u8 Hdcp1DeviceDownstream;
+} XHdcp22_Rx_Topology;
+
+/**
+ * This typedef contains configuration information for the device.
+ */
+typedef struct
+{
+	/** Unique ID of device instance */
+	u16 DeviceId;
+	/** Base address of subsystem */
+	UINTPTR BaseAddress;
+	/** HDCP22 over specified protocol (i.e. hdmi) */
+	int Protocol;
+	/** HDCP22 mode (i.e. receiver, repeater, or converter) */
+	int Mode;
+	/** Timer device instance ID */
+	u32 TimerDeviceId;
+	/** Cipher device instance ID */
+	u32 CipherDeviceId;
+	/** Mongomery multiplier device instance ID */
+	u32 MontMultDeviceId;
+	/** Random number generator device instance ID */
+	u32 RngDeviceId;
+} XHdcp22_Rx_Config;
+
+/**
+ * The XHdcp driver instance data. The user is required to
+ * allocate a variable of this type for every HDCP-RX device in the
+ * system. A pointer to a variable of this type is then passed to the driver
+ * API functions.
+ */
+typedef struct
+{
+	/** HDCP-RX config structure */
+	XHdcp22_Rx_Config Config;
+	/** Indicates device is initialized and ready */
+	u32 IsReady;
+	/** RxCaps set during initialization */
+	u8 RxCaps[3];
+	/** DCP public certificate pointer */
+	const u8 *PublicCertPtr;
+	/** RSA private key pointer */
+	const u8 *PrivateKeyPtr;
+	/** Montgomery NPrimeP array */
+	u8 NPrimeP[64];
+	/** Montgomery NPrimeQ array */
+	u8 NPrimeQ[64];
+	/** HDCP-RX authentication and key exchange info */
+	XHdcp22_Rx_Info Info;
+	/** HDCP-RX authentication and key exchange parameters */
+	XHdcp22_Rx_Parameters Params;
+	/** State function pointer */
+	XHdcp22_Rx_StateFunc StateFunc;
+	/** Message handles */
+	XHdcp22_Rx_Handles Handles;
+	/** Log instance */
+	XHdcp22_Rx_Log Log;
+	/** Montgomery multiplier instance */
+	XHdcp22_mmult MmultInst;
+	/** Timer instance */
+	XTmrCtr TimerInst;
+	/** Random number generator instance */
+	XHdcp22_Rng RngInst;
+	/** Cipher instance */
+	XHdcp22_Cipher CipherInst;
+	/** Message structure */
+	u8 MessageBuffer[XHDCP22_RX_MAX_MESSAGE_SIZE];
+	/** Message size */
+	int MessageSize;
+	/** Repeater topology instance */
+	XHdcp22_Rx_Topology Topology;
+#ifdef _XHDCP22_RX_TEST_
+	/** Test instance */
+	XHdcp22_Rx_Test Test;
+#endif
+	u8 Hdcp22Broadcast;
+} XHdcp22_Rx;
+
+/***************** Macros (Inline Functions) Definitions ********************/
+
+/************************** Function Prototypes *****************************/
+/* Functions for initializing and running driver */
+XHdcp22_Rx_Config *XHdcp22Rx_LookupConfig(u16 DeviceId);
+int  XHdcp22Rx_CfgInitialize(XHdcp22_Rx *InstancePtr, XHdcp22_Rx_Config *ConfigPtr,
+       UINTPTR EffectiveAddr);
+int  XHdcp22Rx_Enable(XHdcp22_Rx *InstancePtr);
+int  XHdcp22Rx_Disable(XHdcp22_Rx *InstancePtr);
+int  XHdcp22Rx_Reset(XHdcp22_Rx *InstancePtr);
+int  XHdcp22Rx_Poll(XHdcp22_Rx *InstancePtr);
+int  XHdcp22Rx_SetCallback(XHdcp22_Rx *InstancePtr,
+       XHdcp22_Rx_HandlerType HandlerType, void *CallbackFunc, void *CallbackRef);
+u32  XHdcp22Rx_GetVersion(XHdcp22_Rx *InstancePtr);
+XTmrCtr* XHdcp22Rx_GetTimer(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_SetBroadcast(XHdcp22_Rx *InstancePtr, u8 enable);
+
+/* Functions for checking status */
+u8   XHdcp22Rx_IsEnabled(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_IsEncryptionEnabled(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_IsInProgress(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_IsAuthenticated(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_IsError(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_Info(XHdcp22_Rx *InstancePtr);
+
+/* Functions used in callback routines */
+void XHdcp22Rx_SetLinkError(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_SetDdcError(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_SetWriteMessageAvailable(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_SetReadMessageComplete(XHdcp22_Rx *InstancePtr);
+
+/* Functions for loading authentication constants */
+void XHdcp22Rx_LoadLc128(XHdcp22_Rx *InstancePtr, const u8 *Lc128Ptr);
+void XHdcp22Rx_LoadPublicCert(XHdcp22_Rx *InstancePtr, const u8 *PublicCertPtr);
+int  XHdcp22Rx_LoadPrivateKey(XHdcp22_Rx *InstancePtr, const u8 *PrivateKeyPtr);
+
+/* Functions for logging */
+void XHdcp22Rx_LogReset(XHdcp22_Rx *InstancePtr, u8 Verbose);
+u32  XHdcp22Rx_LogGetTimeUSecs(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_LogWr(XHdcp22_Rx *InstancePtr, u16 Evt, u16 Data);
+XHdcp22_Rx_LogItem* XHdcp22Rx_LogRd(XHdcp22_Rx *InstancePtr);
+int XHdcp22Rx_LogShow(XHdcp22_Rx *InstancePtr, char *buff, int buff_size);
+
+/* Functions for repeater upstream interface */
+void XHdcp22Rx_SetTopology(XHdcp22_Rx *InstancePtr, const XHdcp22_Rx_Topology *TopologyPtr);
+void XHdcp22Rx_SetTopologyReceiverIdList(XHdcp22_Rx *InstancePtr, const u8 *ListPtr, u32 ListSize);
+void XHdcp22Rx_SetTopologyField(XHdcp22_Rx *InstancePtr, XHdcp22_Rx_TopologyField Field, u8 Value);
+void XHdcp22Rx_SetTopologyUpdate(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_SetRepeater(XHdcp22_Rx *InstancePtr, u8 Set);
+u8   XHdcp22Rx_IsRepeater(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_GetContentStreamType(XHdcp22_Rx *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP22_RX_H_ */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx_crypt.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx_crypt.c
@@ -0,0 +1,1323 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file xhdcp22_rx_crypt.c
+* @{
+* @details
+*
+* This file contains the implementation of the PKCS #1 Public Key Cryptography
+* Standard and other cryptographic functions used during HDCP 2.2 receiver
+* authentication and key exchange.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+* 2.00  MH   04/14/16 Updated for repeater upstream support.
+* 2.20  MH   06/21/17 Updated for 64 bit support.
+*</pre>
+*
+*****************************************************************************/
+
+/***************************** Include Files ********************************/
+//#include "stdio.h"
+//#include "stdlib.h"
+#include <linux/string.h>
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xil_printf.h"
+#include "xhdcp22_rx_i.h"
+#include "xhdcp22_common.h"
+
+/************************** Constant Definitions ****************************/
+
+/**************************** Type Definitions ******************************/
+
+/***************** Macros (Inline Functions) Definitions ********************/
+#define XHdcp22Rx_MpSizeof(A) (sizeof(A)/sizeof(u32))
+
+/************************** Variable Definitions ****************************/
+
+/************************** Function Prototypes *****************************/
+/* Functions for implementing PCKS1 */
+static int  XHdcp22Rx_Pkcs1Rsaep(const XHdcp22_Rx_KpubRx *KpubRx, u8 *Message,
+	            u8 *EncryptedMessage);
+static int  XHdcp22Rx_Pkcs1Rsadp(XHdcp22_Rx *InstancePtr, const XHdcp22_Rx_KprivRx *KprivRx,
+	            u8 *EncryptedMessage, u8 *Message);
+static int  XHdcp22Rx_Pkcs1Mgf1(const u8 *seed, const u32 seedlen, u8  *mask, u32 masklen);
+static int  XHdcp22Rx_Pkcs1EmeOaepEncode(const u8 *Message, const u32 MessageLen,
+	            const u8 *MaskingSeed, u8 *EncodedMessage);
+static int  XHdcp22Rx_Pkcs1EmeOaepDecode(u8 *EncodedMessage, u8 *Message, int *MessageLen);
+static void XHdcp22Rx_Pkcs1MontMultFiosInit(XHdcp22_Rx *InstancePtr, u32 *N,
+	            const u32 *NPrime, int NDigits);
+#ifndef _XHDCP22_RX_SW_MMULT_
+static void XHdcp22Rx_Pkcs1MontMultFios(XHdcp22_Rx *InstancePtr, u32 *U, u32 *A,
+	            u32 *B, int NDigits);
+#else
+static void XHdcp22Rx_Pkcs1MontMultFiosStub(u32 *U, u32 *A, u32 *B, u32 *N,
+	            const u32 *NPrime, int NDigits);
+static void XHdcp22Rx_Pkcs1MontMultAdd(u32 *A, u32 C, int SDigit, int NDigits);
+#endif
+static int  XHdcp22Rx_Pkcs1MontExp(XHdcp22_Rx *InstancePtr, u32 *C, u32 *A, u32 *E,
+	            u32 *N, const u32 *NPrime, int NDigits);
+
+/* Functions for implementing other cryptographic tasks */
+static void XHdcp22Rx_ComputeDKey(const u8* Rrx, const u8* Rtx, const u8 *Km,
+	            const u8 *Rn, u8 *Ctr, u8 *DKey);
+static void XHdcp22Rx_Xor(u8 *Cout, const u8 *Ain, const u8 *Bin, u32 Len);
+
+/*****************************************************************************/
+/**
+* This function is used to calculate the Montgomery NPrime. NPrime is
+* calculated from the following equation R*Rinv - N*NPrime == 1.
+* For the HDCP2.2 receiver the modulus N has a fixed size
+* of k = 512bits. Given k, the value R = 2^(k), and Rinv is the modular
+* inverse of R.
+*
+* Reference:
+* Analyzing and Comparing Montgomery Multiplication Algorithms
+* IEEE Micro, 16(3):26-33,June 1996
+* By: Cetin Koc, Tolga Acar, and Burton Kaliski
+*
+* @param	NPrime is the calculated value and 2*NDigits in Size.
+* @param	N is modulus
+* @param	NDigits is the integer precision of arguments (N, NPrime), which
+* 			should always be 16 for the HDCP2.2 receiver.
+*
+* @return	XST_SUCCESS or FAILURE.
+*
+* @note		None.
+******************************************************************************/
+int XHdcp22Rx_CalcMontNPrime(u8 *NPrime, const u8 *N, int NDigits)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(NPrime != NULL);
+	Xil_AssertNonvoid(N != NULL);
+	Xil_AssertNonvoid(NDigits == 16);
+
+	u32 N_i[XHDCP22_RX_N_SIZE/4];
+	u32 NPrime_i[XHDCP22_RX_N_SIZE/4];
+	u32 R[XHDCP22_RX_N_SIZE/4];
+	u32 RInv[XHDCP22_RX_N_SIZE/4];
+	u32 T1[XHDCP22_RX_N_SIZE/2];
+	u32 T2[XHDCP22_RX_N_SIZE/2];
+
+	/* Clear variables */
+	memset(N_i, 0, sizeof(N_i));
+	memset(NPrime_i, 0, sizeof(NPrime_i));
+	memset(R, 0, sizeof(R));
+	memset(RInv, 0, sizeof(RInv));
+	memset(T1, 0, sizeof(T1));
+	memset(T2, 0, sizeof(T2));
+
+	/* Convert from octet string */
+	mpConvFromOctets(N_i, XHdcp22Rx_MpSizeof(N_i), N, 4*NDigits);
+
+	/* Step 1: R = 2^(NDigits*32) */
+	R[0] = 1;
+	mpShiftLeft(R, R, 32*NDigits, XHdcp22Rx_MpSizeof(R));
+
+	/* Step 2: Rinv = R^(-1)*mod(N) */
+	T1[0] = 0;
+	memcpy(T1, N_i, sizeof(N_i)); // Increase precision of N
+	if(mpModInv(RInv, R, T1, XHdcp22Rx_MpSizeof(RInv)))
+	{
+		xil_printf("ERROR: Failed Rinv Calculation\n\r");
+		return XST_FAILURE;
+	}
+
+	/* Step 3: NPrime = (R*Rinv-1)/N */
+	mpMultiply(T1, R, RInv, 2*NDigits);
+	memset(T2, 0, sizeof(T2));
+	T2[0] = 1;
+	mpSubtract(T1, T1, T2, XHdcp22Rx_MpSizeof(T1));
+	mpDivide(NPrime_i, T2, T1, XHdcp22Rx_MpSizeof(NPrime_i), (u32 *)N_i, NDigits);
+
+	/* Step 4: Sanity Check, R*Rinv - N*NPrime == 1 */
+	mpMultiply(T1, R, RInv, 2*NDigits);
+	mpMultiply(T2, (u32 *)N_i, NPrime_i, XHdcp22Rx_MpSizeof(NPrime_i));
+	mpSubtract(T1, T1, T2, XHdcp22Rx_MpSizeof(T1));
+	memset(T2, 0, sizeof(T2));
+	T2[0] = 1;
+	if(!mpEqual(T1, T2, XHdcp22Rx_MpSizeof(T1)))
+	{
+		xil_printf("ERROR: Failed NPrime Calculation\n\r");
+		return XST_FAILURE;
+	}
+
+	/* Convert to octet string */
+	mpConvToOctets(NPrime_i, NDigits, NPrime, 4*NDigits);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements the RSAES-OAEP-Encrypt operation. The message
+* is encoded using EME-OAEP and then encrypted with the public key
+* using RSAEP.
+*
+* Reference: PKCS#1 v2.1, Section 7.1.1
+*
+* @param	KpubRx is the RSA public key structure containing the 1024 bit
+* 			modulus and 24 bit public exponent.
+* @param	Message is the octet string to be encrypted.
+* @param	MessageLen is the length of octet string to be encrypted and
+* 			must be less than or equal to (nLen - 2*hLen - 2)
+* @param	MaskingSeed is the random octet string seed of length hLen
+* 			used by EME-OAEP encoding function.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+int XHdcp22Rx_RsaesOaepEncrypt(const XHdcp22_Rx_KpubRx *KpubRx, const u8 *Message,
+	const u32 MessageLen, const u8 *MaskingSeed, u8 *EncryptedMessage)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(KpubRx != NULL);
+	Xil_AssertNonvoid(Message != NULL);
+	Xil_AssertNonvoid(MessageLen > 0);
+	Xil_AssertNonvoid(MaskingSeed != NULL);
+	Xil_AssertNonvoid(EncryptedMessage != NULL);
+
+	u8 em[XHDCP22_RX_N_SIZE];
+	int Status;
+
+	/* Step 1: Length checking */
+	if(MessageLen > (XHDCP22_RX_N_SIZE - 2*XHDCP22_RX_HASH_SIZE - 2))
+	{
+		return XST_FAILURE;
+	}
+
+	/* Step 2: EME-OAEP Encoding */
+	Status = XHdcp22Rx_Pkcs1EmeOaepEncode(Message, MessageLen, MaskingSeed, em);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 3: RSA encryption */
+	Status = XHdcp22Rx_Pkcs1Rsaep(KpubRx, em, EncryptedMessage);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements the RSAES-OAEP-Decrypt operation. The message is
+* 	decrypted using RSADP and then decoded using EME-OAEP.
+*
+* Reference: PKCS#1 v2.1, Section 7.1.2
+*
+* @param	InstancePtr is a pointer to the MMULT instance.
+* @param	KprivRx is the RSA private key structure containing the quintuple.
+* @param	EncryptedMessage is the 128 byte octet string to be decrypted.
+* @param	Message is the octet string after decryption.
+* @param	MessageLen is the length of the message octet string after decryption.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+int  XHdcp22Rx_RsaesOaepDecrypt(XHdcp22_Rx *InstancePtr, const XHdcp22_Rx_KprivRx *KprivRx,
+	u8 *EncryptedMessage, u8 *Message, int *MessageLen)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(KprivRx != NULL);
+	Xil_AssertNonvoid(EncryptedMessage != NULL);
+	Xil_AssertNonvoid(Message != NULL);
+
+	u8  em[XHDCP22_RX_N_SIZE];
+	u32 Status;
+
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_RSA);
+
+	/* Step 1: Length checking, Skip */
+
+	/* Step 2: RSA decryption */
+	Status = XHdcp22Rx_Pkcs1Rsadp(InstancePtr, KprivRx, EncryptedMessage, em);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 3: EME-OAEP decoding */
+	Status = XHdcp22Rx_Pkcs1EmeOaepDecode(em, Message, MessageLen);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	XHdcp22Rx_LogWr(InstancePtr, XHDCP22_RX_LOG_EVT_DEBUG, XHDCP22_RX_LOG_DEBUG_COMPUTE_RSA_DONE);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function generates random octets.
+*
+* @param  NumOctets is the number of octets in the random number.
+* @param  RandomNumberPtr is a pointer to the random number.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Rx_GenerateRandom(XHdcp22_Rx *InstancePtr, int NumOctets,
+                              u8* RandomNumberPtr)
+{
+	/* Use hardware generator */
+	XHdcp22Rng_GetRandom(&InstancePtr->RngInst, RandomNumberPtr, NumOctets, NumOctets);
+}
+
+/****************************************************************************/
+/**
+* This function implements the RSAEP primitive.
+*
+* Reference: PKCS#1 v2.1, Section 5.1.1
+*
+* @param	KpubRx is the RSA public key structure containing the 1024 bit
+* 			modulus and 24 bit public exponent.
+* @param	Message is the 128 byte octet string to be encrypted.
+* @param	EncryptedMessage is the 128 byte octet string after encryption.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Rx_Pkcs1Rsaep(const XHdcp22_Rx_KpubRx *KpubRx, u8 *Message, u8 *EncryptedMessage)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(KpubRx != NULL);
+	Xil_AssertNonvoid(Message != NULL);
+	Xil_AssertNonvoid(EncryptedMessage != NULL);
+
+	u32 N[XHDCP22_RX_N_SIZE/4];
+	u32 E[XHDCP22_RX_N_SIZE/4];
+	u32 M[XHDCP22_RX_N_SIZE/4];
+	u32 C[XHDCP22_RX_N_SIZE/4];
+
+	/* Convert octet string to integer */
+	mpConvFromOctets(N, XHDCP22_RX_N_SIZE/4, KpubRx->N, XHDCP22_RX_N_SIZE);
+	mpConvFromOctets(E, XHDCP22_RX_N_SIZE/4, KpubRx->e, 3);
+	mpConvFromOctets(M, XHDCP22_RX_N_SIZE/4, Message, XHDCP22_RX_N_SIZE);
+
+	/* Generate cipher text, c = m^e*mod(n) */
+	mpModExp(C, M, E, N, XHDCP22_RX_N_SIZE/4);
+
+	/* Convert integer to octet string */
+	mpConvToOctets(C, XHDCP22_RX_N_SIZE/4, EncryptedMessage, XHDCP22_RX_N_SIZE);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements the RSADP primitive using the Chinese Remainder
+* Theorem (CRT).
+*
+* Reference: PKCS#1 v2.1, Section 5.1.2
+*
+* @param	InstancePtr is a pointer to the MMULT instance.
+* @param	KprivRx is the RSA private key structure containing the quintuple.
+* @param	EncryptedMessage is the 128 byte octet string to be decrypted.
+* @param	Message is the 128 byte decrypted octet string.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Rx_Pkcs1Rsadp(XHdcp22_Rx *InstancePtr, const XHdcp22_Rx_KprivRx *KprivRx,
+	u8 *EncryptedMessage, u8 *Message)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(KprivRx != NULL);
+	Xil_AssertNonvoid(EncryptedMessage != NULL);
+	Xil_AssertNonvoid(Message != NULL);
+
+	u32 A[XHDCP22_RX_N_SIZE/4];
+	u32 B[XHDCP22_RX_N_SIZE/4];
+	u32 C[XHDCP22_RX_N_SIZE/4];
+	u32 D[XHDCP22_RX_N_SIZE/4];
+	u32 M1[XHDCP22_RX_N_SIZE/4];
+	u32 M2[XHDCP22_RX_N_SIZE/4];
+	u32 Status;
+
+	/* Clear variables */
+	memset(A, 0, sizeof(A));
+	memset(B, 0, sizeof(B));
+	memset(C, 0, sizeof(C));
+	memset(D, 0, sizeof(D));
+	memset(M1, 0, sizeof(M1));
+	memset(M2, 0, sizeof(M2));
+
+	/* Step 2b part I: Generate m1 = c^dP * mod(p) */
+	mpConvFromOctets(A, XHdcp22Rx_MpSizeof(A), KprivRx->p, XHDCP22_RX_P_SIZE);
+	mpConvFromOctets(B, XHdcp22Rx_MpSizeof(B), KprivRx->dp, XHDCP22_RX_P_SIZE);
+	mpConvFromOctets(C, XHdcp22Rx_MpSizeof(C), EncryptedMessage, XHDCP22_RX_N_SIZE);
+	mpConvFromOctets(D, XHdcp22Rx_MpSizeof(D), InstancePtr->NPrimeP, XHDCP22_RX_P_SIZE);
+	//Status = mpModExp(M1, C, B, A, XHDCP22_RX_N_SIZE/4);
+	Status = XHdcp22Rx_Pkcs1MontExp(InstancePtr, M1, C, B, A, D, 16);
+
+	/* Step 2b part I: Generate m2 = c^dQ * mod(q) */
+	mpConvFromOctets(A, XHdcp22Rx_MpSizeof(A), KprivRx->q, XHDCP22_RX_P_SIZE);
+	mpConvFromOctets(B, XHdcp22Rx_MpSizeof(B), KprivRx->dq, XHDCP22_RX_P_SIZE);
+	mpConvFromOctets(D, XHdcp22Rx_MpSizeof(D), InstancePtr->NPrimeQ, XHDCP22_RX_P_SIZE);
+	//Status = mpModExp(M2, C, D, B, XHDCP22_RX_N_SIZE/4);
+	Status = XHdcp22Rx_Pkcs1MontExp(InstancePtr, M2, C, B, A, D, 16);
+
+	/* Step 2b part II: Skip since u=2 */
+
+	/* Step 2b part III: Generate h = (m1 - m2) * qInv * mod(p) */
+	mpConvFromOctets(A, XHdcp22Rx_MpSizeof(A), KprivRx->p, XHDCP22_RX_P_SIZE);
+	Status = mpSubtract(D, M1, M2, XHdcp22Rx_MpSizeof(D)); // mdiff = m1 -m2
+	if(Status != XST_SUCCESS)
+	{
+		mpAdd(M1, M1, A, XHdcp22Rx_MpSizeof(M1));
+		mpSubtract(D, M1, M2, XHdcp22Rx_MpSizeof(D));
+	}
+	mpConvFromOctets(C, XHdcp22Rx_MpSizeof(C), KprivRx->qinv, XHDCP22_RX_P_SIZE);
+	Status = mpModMult(C, D, C, A, XHDCP22_RX_N_SIZE/4); // h = mdiff * qInv * mod(p)
+
+	/* Step 2b part IV: Generate m = m2 + q * h */
+	mpConvFromOctets(A, XHdcp22Rx_MpSizeof(A), KprivRx->q, XHDCP22_RX_P_SIZE);
+	Status = mpMultiply(D, A, C, XHDCP22_RX_P_SIZE/4); // qh = q * h
+	Status = mpAdd(C, M2, D, XHDCP22_RX_N_SIZE/4); // m = m2 + qh
+
+	/* Convert integer to octet string */
+	mpConvToOctets(C, XHdcp22Rx_MpSizeof(C), Message, XHDCP22_RX_N_SIZE);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements the Mask Generation Function MGF1.
+* The underlying hash function used is SHA256.
+*
+* Reference: PKCS#1 v2.1, Section B.2.1
+*
+* @param	Seed is the octet string from which the mask is generated.
+* @param	SeedLen is the length of the seed in octet string.
+* @param	Mask is the output octet string after MGF1.
+* @param	MaskLen is the desired length of the mask with a length
+* 			less than or equal to 128 bytes.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Rx_Pkcs1Mgf1(const u8 *Seed, const u32 SeedLen, u8  *Mask, u32 MaskLen)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(Seed != NULL);
+	Xil_AssertNonvoid(SeedLen > 0);
+	Xil_AssertNonvoid(Mask != NULL);
+	Xil_AssertNonvoid(MaskLen > 0);
+
+	u8  Hash[XHDCP22_RX_HASH_SIZE];
+	u8  HashData[XHDCP22_RX_N_SIZE];	// SeedLen+4
+	u32 C;
+	u8  Cbig[4];
+	u8  T[XHDCP22_RX_N_SIZE]; 		// MaskLen + XHDCP22_RX_HASH_SIZE
+
+	/* Step 2: Clear T */
+	memset(T, 0x00, sizeof(T));
+
+	/* Step 3: T = T || SHA256(mgfSeed || C) */
+	memcpy(HashData, Seed, SeedLen);
+
+	for(C=0; (C*XHDCP22_RX_HASH_SIZE) < MaskLen; C++)
+	{
+		/* Convert counter value to big endian */
+		Cbig[0] = ((C >> 24) & 0xFF);
+		Cbig[1] = ((C >> 16) & 0xFF);
+		Cbig[2] = ((C >> 8) & 0xFF);
+		Cbig[3] = (C & 0xFF);
+
+		/* Constructing Hash Input */
+		memcpy(HashData+SeedLen, &Cbig, 4);
+
+		/* Computing Hash */
+		XHdcp22Cmn_Sha256Hash(HashData, SeedLen+4, Hash);
+
+		/* Appending Hash to T */
+		memcpy(T+C*XHDCP22_RX_HASH_SIZE, Hash, XHDCP22_RX_HASH_SIZE);
+	}
+
+	/* Step 4: Output leading maskLen octets of T */
+	memcpy(Mask, T, MaskLen);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements EME-OAEP encoding. The label L is the empty
+* string and the underlying hash function is SHA256.
+*
+* Reference: PKCS#1 v2.1, Section 7.1.1, Part 2
+*
+* @param	Message is the octet string to be encoded
+* @param	MessageLen is the length of the octet string to be encoded.
+* @param	MaskingSeed is the random octet string seed of length hLen.
+* @param	EncodedMessage is the 128 byte encoded octet string.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Rx_Pkcs1EmeOaepEncode(const u8 *Message, const u32 MessageLen,
+	const u8 *MaskingSeed, u8 *EncodedMessage)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(Message != NULL);
+	Xil_AssertNonvoid(MessageLen > 0);
+	Xil_AssertNonvoid(MaskingSeed != NULL);
+	Xil_AssertNonvoid(EncodedMessage != NULL);
+
+	u8  lHash[XHDCP22_RX_HASH_SIZE];
+	u8  seed[XHDCP22_RX_HASH_SIZE];
+	u8  dbMask[XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1];
+	u8  DB[XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1];
+	u8  seedMask[XHDCP22_RX_HASH_SIZE];
+	u32 Status;
+
+	/* Step 2a: L is the empty string */
+	XHdcp22Cmn_Sha256Hash(NULL,0,lHash);
+
+	/* Step 2b: Generate PS by initializing DB to zeros */
+	memset(DB, 0x00, sizeof(DB));
+
+	/* Step 2c: Generate DB = lHash || PS || 0x01 || M */
+	memcpy(DB, lHash, XHDCP22_RX_HASH_SIZE);
+	DB[XHDCP22_RX_N_SIZE-MessageLen-XHDCP22_RX_HASH_SIZE-2] = 0x01;
+	memcpy(DB+XHDCP22_RX_N_SIZE-MessageLen-XHDCP22_RX_HASH_SIZE-1, Message, MessageLen);
+
+	/* Step 2d: Generate random seed of length hLen
+	 *   The random seed is passed in as an argument to this function.
+	 */
+
+	/* Step 2e: Generate dbMask = MGF1(seed, length(DB)) */
+	Status = XHdcp22Rx_Pkcs1Mgf1(MaskingSeed, XHDCP22_RX_HASH_SIZE, dbMask,
+						XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 2f: Generate maskedDB = DB xor dbMask */
+	XHdcp22Rx_Xor(DB, DB, dbMask, XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1);
+
+	/* Step 2g: Generate seedMask = MGF(maskedDB, length(seed)) */
+	Status = XHdcp22Rx_Pkcs1Mgf1(DB, XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1,
+						seedMask, XHDCP22_RX_HASH_SIZE);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 2h: Generate maskedSeed = seed xor seedMask */
+	XHdcp22Rx_Xor(seed, MaskingSeed, seedMask, XHDCP22_RX_HASH_SIZE);
+
+	/* Step 2i: Form encoded message EM = 0x00 || maskedSeed || maskedDB */
+	memset(EncodedMessage, 0x00, XHDCP22_RX_N_SIZE);
+	memcpy(EncodedMessage+1, seed, XHDCP22_RX_HASH_SIZE);
+	memcpy(EncodedMessage+1+XHDCP22_RX_HASH_SIZE, DB, XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements EME-OAEP decoding. The label L is the empty string
+* and the underlying hash function is SHA256.
+*
+* Reference: PKCS#1 v2.1, Section 7.1.2, Part 3
+*
+* @param	EncodedMessage is the 128 byte encoded octet string.
+* @param	Message is decoded octet string.
+* @param	MessageLen is the length of the decoded octet string.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Rx_Pkcs1EmeOaepDecode(u8 *EncodedMessage, u8 *Message, int *MessageLen)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(EncodedMessage != NULL);
+	Xil_AssertNonvoid(Message != NULL);
+	Xil_AssertNonvoid(MessageLen != NULL);
+
+	u8  lHash[XHDCP22_RX_HASH_SIZE];
+	u8  *maskedSeed;
+	u8  seed[XHDCP22_RX_HASH_SIZE];
+	u8  *maskedDB;
+	u8  DB[XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1];
+	u32 Offset = XHDCP22_RX_HASH_SIZE;
+	u32 Status;
+
+	/* Step 3a: L is the empty string */
+	XHdcp22Cmn_Sha256Hash(NULL,0,lHash);
+
+	/* Step 3b: Separate EM = Y || maskedSeed || maskedDB */
+	maskedSeed = EncodedMessage+1;
+	maskedDB = EncodedMessage+1+XHDCP22_RX_HASH_SIZE;
+
+	/* Step 3c: Generate seedMask = MGF(maskedDB, hLen) */
+	Status = XHdcp22Rx_Pkcs1Mgf1(maskedDB, XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1,
+						seed, XHDCP22_RX_HASH_SIZE);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 3d: Generate seed = maskedSeed xor seedMask */
+	XHdcp22Rx_Xor(seed, maskedSeed, seed, XHDCP22_RX_HASH_SIZE);
+
+	/* Step 3e: Generate dbMask = MGF(seed, k-hLen-1) */
+	Status = XHdcp22Rx_Pkcs1Mgf1(seed, XHDCP22_RX_HASH_SIZE, DB,
+						XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 3f: Generate DB = maskedDB xor dbMask */
+	XHdcp22Rx_Xor(DB, maskedDB, DB, XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1);
+
+	/*
+	 * Step 3g: Separate DB = lHash' || PS || 0x01 || M
+	 *
+	 * - Note: To avoid side channel attacks from now on run all
+	 * code even in the error case. This avoids possible timing
+	 * attacks as described by Manger.
+	 */
+	Status = XST_SUCCESS;
+
+	/* Compare Y */
+	if(*(EncodedMessage) != 0x00)
+	{
+		Status = XST_FAILURE;
+	}
+
+	/* Compare lHash' */
+	if(memcmp(DB, lHash, XHDCP22_RX_HASH_SIZE) != 0)
+	{
+		Status = XST_FAILURE;
+	}
+
+	/* Compare PS */
+	for(Offset = XHDCP22_RX_HASH_SIZE; Offset < (XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1); Offset++)
+	{
+		if(DB[Offset] == 0x01)
+		{
+			break;
+		}
+		else if(DB[Offset] != 0x00)
+		{
+			Status = XST_FAILURE;
+		}
+	}
+
+	/* Return Error */
+	if(Status != XST_SUCCESS)
+	{
+		return XST_FAILURE;
+	}
+
+	/* Extract M */
+	*MessageLen = (XHDCP22_RX_N_SIZE-XHDCP22_RX_HASH_SIZE-1) - (Offset + 1);
+	memcpy(Message, DB+Offset+1, *MessageLen);
+
+	return XST_SUCCESS;
+}
+
+#ifdef _XHDCP22_RX_SW_MMULT_
+/****************************************************************************/
+/**
+* This function performs a carry propagation adding C to the input
+* array A of size NDigits, given by the first argument starting from
+* the first element SDigit, and propagates it until no further carry
+* is generated.
+*
+* ADD(A[i],C)
+*
+* Reference:
+* Analyzing and Comparing Montgomery Multiplication Algorithms
+* IEEE Micro, 16(3):26-33,June 1996
+* By: Cetin Koc, Tolga Acar, and Burton Kaliski
+*
+* @param	A is an input array of size NDigits
+* @param	C is the value being added to the input A
+* @param	SDigit is the start digit
+* @param	NDigits is the integer precision of the arguments (A)
+*
+* @return	None.
+*
+* @note		None.
+*****************************************************************************/
+static void XHdcp22Rx_Pkcs1MontMultAdd(u32 *A, u32 C, int SDigit, int NDigits)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(A != NULL);
+	Xil_AssertVoid(SDigit <= NDigits);
+
+	int i;
+
+	for(i=SDigit; i<NDigits; i++)
+	{
+		C = mpAdd(A+i, A+i, &C, 1);
+
+		if(C == 0)
+		{
+			return;
+		}
+	}
+}
+#endif
+
+#ifdef _XHDCP22_RX_SW_MMULT_
+/****************************************************************************/
+/**
+* This function implements the Montgomery Modular Multiplication (MMM)
+* Finely Integrated Operand Scanning (FIOS) algorithm. The FIOS method
+* interleaves multiplication and reduction operations. Requires NDigits+3
+* words of temporary storage.
+*
+* U = MontMult(A,B,N)
+*
+* Reference:
+* Analyzing and Comparing Montgomery Multiplication Algorithms
+* IEEE Micro, 16(3):26-33,June 1996
+* By: Cetin Koc, Tolga Acar, and Burton Kaliski
+*
+* @param	U is the MMM result
+* @param	A is the n-residue input, A' = A*R mod N
+* @param	B is the n-residue input, B' = B*R mod N
+* @param	N is the modulus
+* @param	NPrime is a pre-computed constant, NPrime = (1-R*Rbar)/N
+* @param	NDigits is the integer precision of the arguments (C,A,B,N,NPrime)
+*
+* @return	None.
+*
+* @note		None.
+*****************************************************************************/
+static void XHdcp22Rx_Pkcs1MontMultFiosStub(u32 *U, u32 *A, u32 *B,
+	u32 *N, const u32 *NPrime, int NDigits)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(U != NULL);
+	Xil_AssertVoid(A != NULL);
+	Xil_AssertVoid(B != NULL);
+	Xil_AssertVoid(N != NULL);
+	Xil_AssertVoid(NPrime != NULL);
+	Xil_AssertVoid(NDigits == 16);
+
+	int i, j;
+	u32 S, C, C1, C2, M[2], X[2];
+	u32 T[XHDCP22_RX_N_SIZE];
+
+	memset(T, 0, 4*(NDigits+3));
+
+	for(i=0; i<NDigits; i++)
+	{
+		// (C,S) = t[0] + a[0]*b[i], worst case 2 words
+		spMultiply(X, A[0], B[i]);	// X[Upper,Lower] = a[0]*b[i]
+		C = mpAdd(&S, T+0, X+0, 1);	// [C,S] = t[0] + X[Lower]
+		mpAdd(&C, &C, X+1, 1);		// [~,C] = C + X[Upper], No carry
+
+		// ADD(t[1],C)
+		XHdcp22Rx_Pkcs1MontMultAdd(T, C, 1, NDigits+3);
+
+		// m = S*n'[0] mod W, where W=2^32
+		// Note: X[Upper,Lower] = S*n'[0], m=X[Lower]
+		spMultiply(M, S, NPrime[0]);
+
+		// (C,S) = S + m*n[0], worst case 2 words
+		spMultiply(X, M[0], N[0]);	// X[Upper,Lower] = m*n[0]
+		C = mpAdd(&S, &S, X+0, 1);	// [C,S] = S + X[Lower]
+		mpAdd(&C, &C, X+1, 1);		// [~,C] = C + X[Upper]
+
+		for(j=1; j<NDigits; j++)
+		{
+			// (C,S) = t[j] + a[j]*b[i] + C, worst case 2 words
+			spMultiply(X, A[j], B[i]);	 	// X[Upper,Lower] = a[j]*b[i], double precision
+			C1 = mpAdd(&S, T+j, &C, 1);		// (C1,S) = t[j] + C
+			C2 = mpAdd(&S, &S, X+0, 1); 	// (C2,S) = S + X[Lower]
+			mpAdd(&C, &C1, X+1, 1);			// (~,C)  = C1 + X[Upper], doesn't produce carry
+			mpAdd(&C, &C, &C2, 1); 			// (~,C)  = C + C2, doesn't produce carry
+
+			// ADD(t[j+1],C)
+			XHdcp22Rx_Pkcs1MontMultAdd(T, C, j+1, NDigits+3);
+
+			// (C,S) = S + m*n[j]
+			spMultiply(X, M[0], N[j]);	// X[Upper,Lower] = m*n[j]
+			C = mpAdd(&S, &S, X+0, 1);	// [C,S] = S + X[Lower]
+			mpAdd(&C, &C, X+1, 1);		// [~,C] = C + X[Upper]
+
+			// t[j-1] = S
+			T[j-1] = S;
+		}
+
+		// (C,S) = t[s] + C
+		C = mpAdd(&S, T+NDigits, &C, 1);
+		// t[s-1] = S
+		T[NDigits-1] = S;
+		// t[s] = t[s+1] + C
+		mpAdd(T+NDigits, T+NDigits+1, &C, 1);
+		// t[s+1] = 0
+		T[NDigits+1] = 0;
+	}
+
+	/* Step 3: if(u>=n) return u-n else return u */
+	if(mpCompare(T, N, NDigits+3) >= 0)
+	{
+		mpSubtract(T, T, N, NDigits+3);
+	}
+
+	memcpy(U, T, 4*NDigits);
+}
+#endif
+
+/****************************************************************************/
+/**
+* This function initializes the Montgomery Multiplier (MMULT) hardware
+* by writing the N and NPrime registers.
+*
+* U = MontMult(A,B,N)
+*
+* Reference:
+* Analyzing and Comparing Montgomery Multiplication Algorithms
+* IEEE Micro, 16(3):26-33,June 1996
+* By: Cetin Koc, Tolga Acar, and Burton Kaliski
+*
+* @param	InstancePtr is a pointer to the MMULT instance.
+* @param	N is the modulus
+* @param	NPrime is a pre-computed constant, NPrime = (1-R*Rbar)/N
+* @param	NDigits is the integer precision of the arguments (C,A,B,N,NPrime)
+*
+* @return	None.
+*
+* @note		None.
+*****************************************************************************/
+static void XHdcp22Rx_Pkcs1MontMultFiosInit(XHdcp22_Rx *InstancePtr, u32 *N,
+	const u32 *NPrime, int NDigits)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(N != NULL);
+	Xil_AssertVoid(NPrime != NULL);
+	Xil_AssertVoid(NDigits == 16);
+
+	/* Check Ready */
+	while(XHdcp22_mmult_IsReady(&InstancePtr->MmultInst) == 0);
+
+	/* Write Register N */
+	XHdcp22_mmult_Write_N_Words(&InstancePtr->MmultInst, 0, (int *)N, NDigits);
+
+	/* Write Register NPrime */
+	XHdcp22_mmult_Write_NPrime_Words(&InstancePtr->MmultInst, 0, (int *)NPrime, NDigits);
+}
+
+#ifndef _XHDCP22_RX_SW_MMULT_
+/****************************************************************************/
+/**
+* This function runs the Montgomery Multiplier (MMULT) hardware to perform
+* the modular multiplication operation required by RSA decryption.
+*
+* U = MontMult(A,B,N)
+*
+* @param	InstancePtr is a pointer to the MMULT instance.
+* @param	U is the MMM result
+* @param	A is the n-residue input, A' = A*R mod N
+* @param	B is the n-residue input, B' = B*R mod N
+* @param	NDigits is the integer precision of the arguments (C,A,B,N,NPrime)
+*
+* @return	None.
+*
+* @note		None.
+*****************************************************************************/
+static void XHdcp22Rx_Pkcs1MontMultFios(XHdcp22_Rx *InstancePtr, u32 *U,
+	u32 *A, u32 *B, int NDigits)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(U != NULL);
+	Xil_AssertVoid(A != NULL);
+	Xil_AssertVoid(B != NULL);
+	Xil_AssertVoid(NDigits == 16);
+
+	/* Check Ready */
+	while(XHdcp22_mmult_IsReady(&InstancePtr->MmultInst) == 0);
+
+	/* Write Register A */
+	XHdcp22_mmult_Write_A_Words(&InstancePtr->MmultInst, 0, (int *)A, NDigits);
+
+	/* Write Register B */
+	XHdcp22_mmult_Write_B_Words(&InstancePtr->MmultInst, 0, (int *)B, NDigits);
+
+	/* Run MontMult */
+	XHdcp22_mmult_Start(&InstancePtr->MmultInst);
+
+	/* Poll Result */
+	while(XHdcp22_mmult_IsDone(&InstancePtr->MmultInst) == 0);
+
+	/* Read Register U */
+	XHdcp22_mmult_Read_U_Words(&InstancePtr->MmultInst, 0, (int *)U, NDigits);
+}
+#endif
+
+/****************************************************************************/
+/**
+* This function performs the modular exponentation operation using the
+* binary square and multiply method.
+*
+* C = ModExp(A, E, N) = A^E*mod(N)
+*
+* @param	C is result of the modular exponentiation
+* @param	A is the base
+* @param	E is the exponent
+* @param	N is the modulus
+* @param	NPrime is a constant
+* @param	NDigits is the integer precision of the arguments (C,A,B,N,NPrime).
+* 			Maximum integer precision is 16.
+*
+* @return	None.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Rx_Pkcs1MontExp(XHdcp22_Rx *InstancePtr, u32 *C, u32 *A,
+	u32 *E, u32 *N, const u32 *NPrime, int NDigits)
+{
+	int Offset;
+	u32 R[XHDCP22_RX_N_SIZE/4];
+	u32 Abar[XHDCP22_RX_N_SIZE/4];
+	u32 Xbar[XHDCP22_RX_N_SIZE/4];
+
+	memset(R, 0, sizeof(R));
+	memset(Abar, 0, sizeof(Abar));
+	memset(Xbar, 0, sizeof(Xbar));
+
+#ifndef _XHDCP22_RX_SW_MMULT_
+	XHdcp22Rx_Pkcs1MontMultFiosInit(InstancePtr, N, NPrime, NDigits);
+#endif
+
+	/* Step 0: R = 2^(NDigits*32) */
+	R[0] = 1;
+	mpShiftLeft(R, R, NDigits*32, XHDCP22_RX_N_SIZE/4);
+
+	/* Step 1: Xbar = 1*R*mod(N) */
+	mpModulo(Xbar, R, XHDCP22_RX_N_SIZE/4, N, NDigits); // Optimization
+
+	/* Step 2: Abar = A*R*mod(N) */
+	mpModMult(Abar, A, Xbar, N, 2*NDigits);
+
+	/* Step 3: Binary square and multiply */
+	for(Offset=32*NDigits-1; Offset>=0; Offset--)
+	{
+#ifndef _XHDCP22_RX_SW_MMULT_
+		XHdcp22Rx_Pkcs1MontMultFios(InstancePtr, Xbar, Xbar, Xbar, NDigits);
+#else
+		XHdcp22Rx_Pkcs1MontMultFiosStub(Xbar, Xbar, Xbar, N, NPrime, NDigits);
+#endif
+
+		if(mpGetBit(E, NDigits, Offset) == TRUE)
+		{
+#ifndef _XHDCP22_RX_SW_MMULT_
+			XHdcp22Rx_Pkcs1MontMultFios(InstancePtr, Xbar, Xbar, Abar, NDigits);
+#else
+			XHdcp22Rx_Pkcs1MontMultFiosStub(Xbar, Xbar, Abar, N, NPrime, NDigits);
+#endif
+		}
+	}
+
+	/* Step 4: C=MonPro(Xbar,1) */
+	memset(R, 0, sizeof(R));
+	R[0] = 1;
+
+#ifndef _XHDCP22_RX_SW_MMULT_
+	XHdcp22Rx_Pkcs1MontMultFios(InstancePtr, C, Xbar, R, NDigits);
+#else
+	XHdcp22Rx_Pkcs1MontMultFiosStub(C, Xbar, R, N, NPrime, NDigits);
+#endif
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function calculates XOR for any array.
+*
+* @param	Cout is the XOR of the input arrays.
+* @param    Ain is the input byte array.
+* @param    Bin is the input byte array.
+* @param    Len is the length of the arrays in bytes.
+*
+* @return	None.
+*
+* @note		None.
+*****************************************************************************/
+static void XHdcp22Rx_Xor(u8 *Cout, const u8 *Ain, const u8 *Bin, u32 Len)
+{
+	while(Len--)
+	{
+		Cout[Len] = Ain[Len] ^ Bin[Len];
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function computes the derived keys used during HDCP 2.2 authentication
+* and key exchange.
+*
+* Reference: HDCP v2.2, section 2.7
+*
+* @param	Rrx is the Rx random generated value.
+* @param	Rtx is the Tx random generated value.
+* @param	Km is the master key generated by tx.
+* @param	Rn is the 64-bit psuedo-random nonce generated by the transmitter.
+* @param	Ctr is the 64-bit AES counter value.
+* @param	DKey is the 128-bit derived key.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+static void XHdcp22Rx_ComputeDKey(const u8* Rrx, const u8* Rtx, const u8 *Km,
+	const u8 *Rn, u8 *Ctr, u8 *DKey)
+{
+	u8 Aes_Iv[XHDCP22_RX_AES_SIZE];
+	u8 Aes_Key[XHDCP22_RX_AES_SIZE];
+
+	/* Verify arguments */
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(DKey != NULL);
+
+	/* AES Key = Km xor Rn */
+	memcpy(Aes_Key, Km, XHDCP22_RX_AES_SIZE);
+	if(Rn != NULL)
+	{
+		XHdcp22Rx_Xor(Aes_Key+XHDCP22_RX_RN_SIZE, Km+XHDCP22_RX_RN_SIZE, Rn, XHDCP22_RX_RN_SIZE);
+	}
+
+	/* AES Input = Rtx || (Rrx xor Ctr) */
+	memcpy(Aes_Iv, Rtx, XHDCP22_RX_RTX_SIZE);
+	if(Ctr == NULL)
+	{
+		memcpy(&Aes_Iv[XHDCP22_RX_RRX_SIZE], Rrx, XHDCP22_RX_RRX_SIZE);
+	}
+	else
+	{
+		XHdcp22Rx_Xor(Aes_Iv+XHDCP22_RX_RTX_SIZE, Rrx, Ctr, XHDCP22_RX_RRX_SIZE);
+	}
+
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, DKey);
+}
+
+/*****************************************************************************/
+/**
+* This function computes HPrime used during HDCP 2.2 authentication and key
+* exchange.
+*
+* Reference: HDCP v2.2, section 2.2
+*
+* @param	Rrx is the Rx random generated value.
+* @param	RxCaps are the capabilities of the receiver.
+* @param	Rtx is the Tx random generated value.
+* @param	TxCaps are the capabilities of the receiver.
+* @param	Km is the master key generated by tx.
+* @param	HPrime is a pointer to the HPrime hash from the HDCP2.2 receiver.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_ComputeHPrime(const u8* Rrx, const u8 *RxCaps, const u8* Rtx,
+	const u8 *TxCaps, const u8 *Km, u8 *HPrime)
+{
+	u8 HashInput[XHDCP22_RX_RTX_SIZE + XHDCP22_RX_RXCAPS_SIZE + XHDCP22_RX_TXCAPS_SIZE];
+	int Idx = 0;
+	u8 Ctr[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01};
+	u8 Kd[2 * XHDCP22_RX_AES_SIZE]; /* dkey0 || dkey 1 */
+
+
+	/* Verify arguments */
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(RxCaps != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(TxCaps != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(HPrime != NULL);
+
+	/* Generate derived keys dkey0 and dkey1
+	   HashKey Kd = dkey0 || dkey1 */
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, NULL, Kd);
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, Ctr, Kd+XHDCP22_RX_AES_SIZE);
+
+	/* HashInput = Rtx || RxCaps || TxCaps */
+	memcpy(HashInput, Rtx, XHDCP22_RX_RTX_SIZE);
+	Idx += XHDCP22_RX_RTX_SIZE;
+	memcpy(&HashInput[Idx], RxCaps, XHDCP22_RX_RXCAPS_SIZE);
+	Idx += XHDCP22_RX_RXCAPS_SIZE;
+	memcpy(&HashInput[Idx], TxCaps, XHDCP22_RX_TXCAPS_SIZE);
+
+	/* Compute H' = HMAC-SHA256(HashInput, Kd) */
+	XHdcp22Cmn_HmacSha256Hash(HashInput, sizeof(HashInput), Kd, XHDCP22_RX_KD_SIZE, HPrime);
+}
+
+/*****************************************************************************/
+/**
+* This function computes Ekh used during HDCP 2.2 authentication and key
+* exchange for pairing with receiver.
+*
+* Reference: HDCP v2.2, section 2.2.1
+*
+* @param	KprivRx is the RSA private key structure containing the quintuple.
+* @param	Km is the master key generated by tx.
+* @param	M is constructed by concatenating Rtx || Rrx.
+* @param	Ekh is the encrypted Km used for pairing.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_ComputeEkh(const u8 *KprivRx, const u8 *Km, const u8 *M, u8 *Ekh)
+{
+	u8 Kh[XHDCP22_RX_HASH_SIZE];
+
+	/* Verify arguments */
+	Xil_AssertVoid(KprivRx != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(M != NULL);
+	Xil_AssertVoid(Ekh != NULL);
+
+	/* Generate Kh = SHA256(p || q || dP || dQ || qInv)[127:0] */
+	XHdcp22Cmn_Sha256Hash(KprivRx, sizeof(XHdcp22_Rx_KprivRx), Kh);
+
+	/* Compute Ekh = AES128(Kh, (Rtx || Rrx)) xor Km */
+	XHdcp22Cmn_Aes128Encrypt(M, Kh+XHDCP22_RX_EKH_SIZE, Ekh);
+	XHdcp22Rx_Xor(Ekh, Ekh, Km, XHDCP22_RX_EKH_SIZE);
+}
+
+/*****************************************************************************/
+/**
+* This function computes LPrime used during HDCP 2.2 locality check.
+*
+* Reference: HDCP v2.2, section 2.3
+*
+* @param	Rn is the 64-bit psuedo-random nonce generated by the transmitter.
+* @param	Km is the 128-bit master key generated by tx.
+* @param	Rrx is the 64-bit pseudo-random number generated by the receiver.
+* @param	Rtx is the 64-bit pseudo-random number generated by the transmitter.
+* @param	LPrime is the 256-bit value generated for locality check.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_ComputeLPrime(const u8 *Rn, const u8 *Km, const u8 *Rrx, const u8 *Rtx, u8 *LPrime)
+{
+	u8 HashKey[XHDCP22_RX_KD_SIZE];
+	u8 Ctr[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01};
+	u8 Kd[2 * XHDCP22_RX_AES_SIZE]; /* dkey0 || dkey 1 */
+
+	/* Verify arguments */
+	Xil_AssertVoid(Rn != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(LPrime != NULL);
+
+	/* Generate derived keys dkey0 and dkey1
+	   HashKey Kd = dkey0 || dkey1 */
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, NULL, Kd);
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, Ctr, Kd+XHDCP22_RX_AES_SIZE);
+
+	/* HashKey = Kd[256:64] || (Kd[63:0] xor Rrx) */
+	memcpy(HashKey, Kd, XHDCP22_RX_KD_SIZE);
+	XHdcp22Rx_Xor(HashKey+(XHDCP22_RX_KD_SIZE-XHDCP22_RX_RRX_SIZE),
+		Kd+(XHDCP22_RX_KD_SIZE-XHDCP22_RX_RRX_SIZE), Rrx, XHDCP22_RX_RRX_SIZE);
+
+	/* LPrime = HMAC-SHA256(Rn, HashKey) */
+	XHdcp22Cmn_HmacSha256Hash(Rn, XHDCP22_RX_RN_SIZE, HashKey, XHDCP22_RX_KD_SIZE, LPrime);
+}
+
+/*****************************************************************************/
+/**
+* This function computes the Ks used during HDCP 2.2 session key exchange.
+*
+* Reference: HDCP v2.2, section 2.4
+*
+* @param	Rrx is the Rx random generated value.
+* @param	Rtx is the Tx random generated value.
+* @param	Km is the master key generated by the transmitter.
+* @param	Rn is the 64-bit psuedo-random nonce generated by the transmitter.
+* @param	Eks is the encrypted session generated by the transmitter.
+* @param	Ks is the decrypted session key.
+*
+* @return	None.
+*
+* @note		None.
+******************************************************************************/
+void XHdcp22Rx_ComputeKs(const u8* Rrx, const u8* Rtx, const u8 *Km, const u8 *Rn,
+	     const u8 *Eks, u8 *Ks)
+{
+	u8 Dkey2[XHDCP22_RX_KS_SIZE];
+	u8 Ctr[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x02};
+
+	/* Verify arguments */
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(Rn != NULL);
+	Xil_AssertVoid(Eks != NULL);
+	Xil_AssertVoid(Ks != NULL);
+
+	/* Generate derived key dkey2 */
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, Rn, Ctr, Dkey2);
+
+	/* Compute Ks = EKs xor (Dkey2 xor Rrx) */
+	memcpy(Ks, Dkey2, XHDCP22_RX_KS_SIZE);
+	XHdcp22Rx_Xor(Ks+XHDCP22_RX_RRX_SIZE, Ks+XHDCP22_RX_RRX_SIZE, Rrx, XHDCP22_RX_RRX_SIZE);
+	XHdcp22Rx_Xor(Ks, Ks, Eks, XHDCP22_RX_KS_SIZE);
+}
+
+/*****************************************************************************/
+/**
+* This function computes VPrime used during HDCP 2.2 repeater
+* authentication.
+*
+* Reference: HDCP v2.2, section 2.3
+*
+* @param  ReceiverIdList is a list of downstream receivers IDs in big-endian
+*         order. Each receiver ID is 5 Bytes.
+* @param  ReceiverIdListSize is the number of receiver Ids in ReceiverIdList.
+*         There can be between 1 and 31 devices in the list.
+* @param  RxInfo is the 16-bit field in the RepeaterAuth_Send_ReceiverID_List
+*         message.
+* @param  Km is the 128-bit master key generated by tx.
+* @param  Rrx is the 64-bit pseudo-random number generated by the receiver.
+* @param  Rtx is the 64-bit pseudo-random number generated by the transmitter.
+* @param  VPrime is the 256-bit value generated for repeater authentication.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+void XHdcp22Rx_ComputeVPrime(const u8 *ReceiverIdList, u32 ReceiverIdListSize,
+       const u8 *RxInfo, const u8 *SeqNumV, const u8 *Km, const u8 *Rrx,
+       const u8 *Rtx, u8 *VPrime)
+{
+	int Idx = 0;
+	u8 HashInput[XHDCP22_RX_SEQNUMV_SIZE +
+					XHDCP22_RX_RXINFO_SIZE +
+					(XHDCP22_RX_MAX_DEVICE_COUNT*XHDCP22_RX_RCVID_SIZE)];
+	int HashInputSize = (ReceiverIdListSize*XHDCP22_RX_RCVID_SIZE) +
+					XHDCP22_RX_SEQNUMV_SIZE + XHDCP22_RX_RXINFO_SIZE;
+	u8 Ctr[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01};
+	u8 Kd[2 * XHDCP22_RX_AES_SIZE]; /* dkey0 || dkey 1 */
+
+	/* Verify arguments */
+	Xil_AssertVoid(ReceiverIdList != NULL);
+	Xil_AssertVoid(ReceiverIdListSize > 0);
+	Xil_AssertVoid(RxInfo != NULL);
+	Xil_AssertVoid(SeqNumV != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(VPrime != NULL);
+
+	/* Generate derived keys dkey0 and dkey1
+	   HashKey Kd = dkey0 || dkey1 */
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, NULL, Kd);
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, Ctr, Kd+XHDCP22_RX_AES_SIZE);
+
+	/* HashInput = ReceiverIdList || RxInfo || SeqNumV */
+	memcpy(HashInput, ReceiverIdList, ReceiverIdListSize*XHDCP22_RX_RCVID_SIZE);
+	Idx += ReceiverIdListSize*XHDCP22_RX_RCVID_SIZE;
+	memcpy(&HashInput[Idx], RxInfo, XHDCP22_RX_RXINFO_SIZE);
+	Idx += XHDCP22_RX_RXINFO_SIZE;
+	memcpy(&HashInput[Idx], SeqNumV, XHDCP22_RX_SEQNUMV_SIZE);
+
+	/* VPrime = HMAC-SHA256(HashInput, Kd) */
+	XHdcp22Cmn_HmacSha256Hash(HashInput, HashInputSize, Kd, XHDCP22_RX_KD_SIZE, VPrime);
+}
+
+/*****************************************************************************/
+/**
+* This function computes VPrime used during HDCP 2.2 repeater
+* authentication.
+*
+* Reference: HDCP v2.2, section 2.3
+*
+* @param  StreamIdType is the 16-bit field in the RepeaterAuth_Send_ReceiverID_List
+* 			  message.
+* @param  SeqNumM is the 24-bit field in the RepeaterAuth_Stream_Manage
+* 			  message.
+* @param  Km is the 128-bit master key generated by tx.
+* @param  Rrx is the 64-bit pseudo-random number generated by the receiver.
+* @param  Rtx is the 64-bit pseudo-random number generated by the transmitter.
+* @param  MPrime is the 256-bit value generated for repeater stream
+*         management ready.
+*
+* @return None.
+*
+* @note	  None.
+******************************************************************************/
+void XHdcp22Rx_ComputeMPrime(const u8 *StreamIdType, const u8 *SeqNumM,
+       const u8 *Km, const u8 *Rrx, const u8 *Rtx, u8 *MPrime)
+{
+	int Idx = 0;
+	u8 HashInput[XHDCP22_RX_STREAMID_SIZE + XHDCP22_RX_SEQNUMM_SIZE];
+	u8 HashKey[XHDCP22_RX_HASH_SIZE];
+	u8 Ctr[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01};
+	u8 Kd[2 * XHDCP22_RX_AES_SIZE]; /* dkey0 || dkey 1 */
+
+	/* Verify arguments */
+	Xil_AssertVoid(StreamIdType != NULL);
+	Xil_AssertVoid(SeqNumM != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(MPrime != NULL);
+
+	/* HashInput = StreamIdType || SeqNumM */
+	memcpy(HashInput, StreamIdType, XHDCP22_RX_STREAMID_SIZE);
+	Idx += XHDCP22_RX_STREAMID_SIZE;
+	memcpy(&HashInput[Idx], SeqNumM, XHDCP22_RX_SEQNUMM_SIZE);
+
+	/* Generate derived keys dkey0 and dkey1
+	   HashKey Kd = dkey0 || dkey1 */
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, NULL, Kd);
+	XHdcp22Rx_ComputeDKey(Rrx, Rtx, Km, NULL, Ctr, Kd+XHDCP22_RX_AES_SIZE);
+
+	/* Hashkey = SHA256(Kd) */
+	XHdcp22Cmn_Sha256Hash(Kd, XHDCP22_RX_KD_SIZE, HashKey);
+
+	/* VPrime = HMAC-SHA256(HashInput, Kd) */
+	XHdcp22Cmn_HmacSha256Hash(HashInput, sizeof(HashInput), HashKey, XHDCP22_RX_HASH_SIZE, MPrime);
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx_i.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx_i.h
@@ -0,0 +1,470 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file xhdcp22_rx_i.h
+* @{
+* @details
+*
+* This header file contains internal data types and functions declarations
+* for the Xilinx HDCP 2.2 Receiver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+* 1.01  MH   03/02/16 Moved prototype of XHdcp22Rx_CalcMontNPrime to
+*                     to internal functions.
+* 1.02  MH   04/14/16 Updated for repeater upstream support.
+*</pre>
+*
+*****************************************************************************/
+
+#ifndef XHDCP22_RX_I_H_		/* prevent circular inclusions */
+#define XHDCP22_RX_I_H_		/* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files ********************************/
+#include "xhdcp22_rx.h"
+#include "xhdcp22_mmult.h"
+
+/************************** Constant Definitions ****************************/
+
+#define XHDCP22_RX_HASH_SIZE              32            /** Hash size in bytes */
+#define XHDCP22_RX_N_SIZE                 128           /** Modulus size in bytes */
+#define XHDCP22_RX_P_SIZE                 64            /** RSA private parameter size in bytes */
+#define XHDCP22_RX_KM_SIZE                16            /** Km size in bytes */
+#define XHDCP22_RX_EKH_SIZE               16            /** Ekh size size in bytes */
+#define XHDCP22_RX_KD_SIZE                32            /** Kd size size in bytes */
+#define XHDCP22_RX_HPRIME_SIZE            32            /** HPrime size size in bytes */
+#define XHDCP22_RX_LPRIME_SIZE            32            /** LPrime size size in bytes */
+#define XHDCP22_RX_RN_SIZE                8             /** Rn size size in bytes */
+#define XHDCP22_RX_RIV_SIZE               8             /** Riv size size in bytes */
+#define XHDCP22_RX_KS_SIZE                16            /** Ks size size in bytes */
+#define XHDCP22_RX_AES_SIZE               16            /** AES size size in bytes */
+#define XHDCP22_RX_RTX_SIZE               8             /** Rtx size size in bytes */
+#define XHDCP22_RX_RRX_SIZE               8             /** Rrx size size in bytes */
+#define XHDCP22_RX_TXCAPS_SIZE            3             /** TxCaps size size in bytes */
+#define XHDCP22_RX_RXCAPS_SIZE            3             /** RxCaps size size in bytes */
+#define XHDCP22_RX_CERT_SIZE              522           /** DCP certificate size in bytes */
+#define XHDCP22_RX_PRIVATEKEY_SIZE        320           /** RSA private key size (64*5) in bytes */
+#define XHDCP22_RX_LC128_SIZE             16            /** Lc128 global constant size in bytes */
+
+#define XHDCP22_RX_RCVID_SIZE             5             /** Repeater ReceiverID size in bytes */
+#define XHDCP22_RX_SEQNUMV_SIZE           3             /** Repeater seq_num_V size in bytes */
+#define XHDCP22_RX_RXINFO_SIZE            2             /** Repeater RxInfo size in bytes */
+#define XHDCP22_RX_VPRIME_SIZE            32            /** Repeater VPrime size in bytes */
+#define XHDCP22_RX_SEQNUMM_SIZE           3             /** Repeater seq_num_M size in bytes */
+#define XHDCP22_RX_MPRIME_SIZE            32            /** Repeater MPrime size in bytes */
+#define XHDCP22_RX_STREAMID_SIZE          2             /** Repeater MPrime size in bytes */
+
+#define XHDCP22_RX_MAX_SEQNUMV            ((1<<24)-1)   /** Repeater maximum seq_num_V count */
+#define XHDCP22_RX_MAX_LCINIT             1024          /** Maximum LC_Init attempts */
+#define XHDCP22_RX_MAX_DEVICE_COUNT       31            /** Repeater maximum devices */
+#define XHDCP22_RX_MAX_DEPTH              4             /** Repeater maximum depth */
+
+#define XHDCP22_RX_DDC_VERSION_REG        0x50          /** Address of DDC version regiser */
+#define XHDCP22_RX_DDC_WRITE_REG          0x60          /** Address of DDC write message regiser */
+#define XHDCP22_RX_DDC_RXSTATUS0_REG      0x70          /** Address of first DDC RxStatus register */
+#define XHDCP22_RX_DDC_RXSTATUS1_REG      0x71          /** Address of second DDC RxStatus register */
+#define XHDCP22_RX_DDC_READ_REG           0x80          /** Address of DDC read message regiser */
+#define XHDCP22_RX_TMR_CTR_0              0             /** First timer counter, used for log timestamps */
+#define XHDCP22_RX_TMR_CTR_1              1             /** Second timer counter, used for protocol timeout*/
+
+#define XHDCP22_RX_TEST_DDC_REGMAP_SIZE   5             /** Size of ddc register map for testing */
+
+/**************************** Type Definitions ******************************/
+
+/**
+ * These constants are the message identification codes.
+ */
+typedef enum
+{
+	XHDCP22_RX_MSG_ID_AKEINIT                   = 2,   /**< AKE_Init message ID */
+	XHDCP22_RX_MSG_ID_AKESENDCERT               = 3,   /**< AKE_Send_Cert message ID */
+	XHDCP22_RX_MSG_ID_AKENOSTOREDKM             = 4,   /**< AKE_No_Stored_km message ID */
+	XHDCP22_RX_MSG_ID_AKESTOREDKM               = 5,   /**< AKE_Stored_km message ID */
+	XHDCP22_RX_MSG_ID_AKESENDHPRIME             = 7,   /**< AKE_Send_H_prime message ID */
+	XHDCP22_RX_MSG_ID_AKESENDPAIRINGINFO        = 8,   /**< AKE_Send_Pairing_Info message ID */
+	XHDCP22_RX_MSG_ID_LCINIT                    = 9,   /**< LC_Init message ID */
+	XHDCP22_RX_MSG_ID_LCSENDLPRIME              = 10,  /**< LC_Send_L_prime message ID */
+	XHDCP22_RX_MSG_ID_SKESENDEKS                = 11,  /**< SKE_Send_Eks message ID */
+	XHDCP22_RX_MSG_ID_REPEATERAUTHSENDRXIDLIST  = 12,  /**< RepeaterAuth_Send_ReceiverID_List message ID */
+	XHDCP22_RX_MSG_ID_REPEATERAUTHSENDACK       = 15,  /**< RepeaterAuth_Send_Ack message ID */
+	XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMMANAGE  = 16,  /**< RepeaterAuth_Stream_Manage message ID */
+	XHDCP22_RX_MSG_ID_REPEATERAUTHSTREAMREADY   = 17   /**< RepeaterAuth_Stream_Ready message ID */
+} XHdcp22_Rx_MessageIds;
+
+/**
+ * These constants define the error conditions encountered during authentication and key exchange.
+ */
+typedef enum
+{
+	XHDCP22_RX_ERROR_FLAG_NONE                                 = 0,     /**< No errors */
+	XHDCP22_RX_ERROR_FLAG_MESSAGE_SIZE                         = 1,     /**< Message size error */
+	XHDCP22_RX_ERROR_FLAG_FORCE_RESET                          = 2,     /**< Force reset after error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_AKEINIT                   = 4,     /**< AKE_Init message processing error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_AKENOSTOREDKM             = 8,     /**< AKE_No_Stored_km message processing error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_AKESTOREDKM               = 16,    /**< AKE_Stored_km message processing error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_LCINIT                    = 32,    /**< LC_Init message processing error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_SKESENDEKS                = 64,    /**< SKE_Send_Eks message processing error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_REPEATERAUTHSENDACK       = 128,   /**< RepeaterAuthSendAck message processing error */
+	XHDCP22_RX_ERROR_FLAG_PROCESSING_REPEATERAUTHSTREAMMANAGE  = 256,   /**< RepeaterAuthStreamManage message processing error */
+	XHDCP22_RX_ERROR_FLAG_LINK_INTEGRITY                       = 512,   /**< Link integrity check error */
+	XHDCP22_RX_ERROR_FLAG_DDC_BURST                            = 1024,  /**< DDC message burst read/write error */
+	XHDCP22_RX_ERROR_FLAG_MAX_LCINIT_ATTEMPTS                  = 2048,  /**< Maximum LC_Init attempts error */
+	XHDCP22_RX_ERROR_FLAG_MAX_REPEATER_TOPOLOGY                = 4096,  /**< Maximum LC_Init attempts error */
+	XHDCP22_RX_ERROR_FLAG_EMPTY_REPEATER_TOPOLOGY              = 8192   /**< Maximum LC_Init attempts error */
+} XHdcp22_Rx_ErrorFlag;
+
+/**
+ * These constants defines the DDC flags used to determine when messages are available
+ * in the write message buffer or when a message has been read out of the read message
+ * buffer.
+ */
+typedef enum
+{
+	XHDCP22_RX_DDC_FLAG_NONE                = 0, /**< Clear DDC flag */
+	XHDCP22_RX_DDC_FLAG_WRITE_MESSAGE_READY = 1, /**< Write message buffer ready to read */
+	XHDCP22_RX_DDC_FLAG_READ_MESSAGE_READY  = 2  /**< Read message buffer ready to write */
+} XHdcp22_Rx_DdcFlag;
+
+/**
+ * These constants are the detailed logging events.
+ */
+typedef enum
+{
+	XHDCP22_RX_LOG_INFO_RESET,                     /**< Reset event */
+	XHDCP22_RX_LOG_INFO_ENABLE,                    /**< Enable event */
+	XHDCP22_RX_LOG_INFO_DISABLE,                   /**< Disable event */
+	XHDCP22_RX_LOG_INFO_REQAUTH_REQ,               /**< Reauthentication request */
+	XHDCP22_RX_LOG_INFO_ENCRYPTION_ENABLE,         /**< Encryption enabled */
+	XHDCP22_RX_LOG_INFO_TOPOLOGY_UPDATE,           /**< Topology update triggered */
+	XHDCP22_RX_LOG_DEBUG_WRITE_MESSAGE_AVAILABLE,  /**< Write message available */
+	XHDCP22_RX_LOG_DEBUG_READ_MESSAGE_COMPLETE,    /**< Read message complete */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_RSA,              /**< RSA decryption of Km computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_RSA_DONE,         /**< RSA decryption of Km computation done */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_KM,               /**< Authentication Km computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_KM_DONE,          /**< Authentication Km computation done */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_HPRIME,           /**< Authentication HPrime computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_HPRIME_DONE,      /**< Authentication HPrime computation done */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_EKH,              /**< Pairing EKh computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_EKH_DONE,         /**< Pairing Ekh computation done */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_LPRIME,           /**< Locality check LPrime computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_LPRIME_DONE,      /**< Locality check LPrime computation done */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_KS,               /**< Session key exchange Ks computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_KS_DONE,          /**< Session key exchange Ks computation done */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_VPRIME,           /**< Locality check VPrime computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_VPRIME_DONE,      /**< Locality check VPrime computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_MPRIME,           /**< Locality check MPrime computation start */
+	XHDCP22_RX_LOG_DEBUG_COMPUTE_MPRIME_DONE,      /**< Locality check MPrime computation start */
+	XHDCP22_RX_LOG_DEBUG_TIMER_START,              /**< Start protocol timer */
+	XHDCP22_RX_LOG_DEBUG_TIMER_EXPIRED             /**< Timer expired */
+} XHdcp22_Rx_LogData;
+
+/**
+ * These constants are used for setting up the desired unit test for standalong testing.
+ */
+typedef enum {
+	XHDCP22_RX_TEST_FLAG_NONE,                           /**< No directed test */
+	XHDCP22_RX_TEST_FLAG_NOSTOREDKM_WITH_RECEIVER,       /**< Directed test flag [No_Stored_km with Receiver] */
+	XHDCP22_RX_TEST_FLAG_STOREDKM_WITH_RECEIVER,         /**< Directed test flag [Stored_km with Receiver]*/
+	XHDCP22_RX_TEST_FLAG_NOSTOREDKM_WITH_REPEATER,       /**< Directed test flag [No_Stored_km with Repeater], Sequence: [List, ListAck, StreamManage, StreamReady] */
+	XHDCP22_RX_TEST_FLAG_STOREDKM_WITH_REPEATER,         /**< Directed test flag [Stored_km with Repeater], Sequence: [List, ListAck, StreamManage, StreamReady] */
+	XHDCP22_RX_TEST_FLAG_REPEATER_MISORDERED_SEQUENCE_1, /**< Directed test flag [Repeater Misordered Sequence 1], Sequence: [StreamManage, StreamReady, List, ListAck] */
+	XHDCP22_RX_TEST_FLAG_REPEATER_MISORDERED_SEQUENCE_2, /**< Directed test flag [Repeater Misordered Sequence 2], Sequence [List, StreamManage, StreamReady, ListAck] */
+	XHDCP22_RX_TEST_FLAG_REPEATER_MISORDERED_SEQUENCE_3, /**< Directed test flag [Repeater Misordered Sequence 3], Sequence [List, StreamManage, ListAck, StreamReady] */
+	XHDCP22_RX_TEST_FLAG_REPEATER_TOPOLOGY_CHANGE,       /**< Directed test flag [Repeater Topology Change] */
+	XHDCP22_RX_TEST_FLAG_REPEATER_TOPOLOGY_TIMEOUT,      /**< Directed test flag [Repeater Topology Timeout] */
+	XHDCP22_RX_TEST_FLAG_INVALID                         /**< Last value the list, only used for checking */
+} XHdcp22_Rx_TestFlags;
+
+/**
+ * These constants are used to set the cores test mode.
+ */
+typedef enum {
+	XHDCP22_RX_TESTMODE_DISABLED,  /**< Test mode disabled */
+	XHDCP22_RX_TESTMODE_NO_TX,     /**< Test mode to emulate transmitter internally used for unit testing */
+	XHDCP22_RX_TESTMODE_SW_TX,     /**< Test mode to emulate transmitter externally used for loopback testing */
+	XHDCP22_RX_TESTMODE_INVALID    /**< Last value the list, only used for checking */
+} XHdcp22_Rx_TestMode;
+
+/**
+ * These constants define the test ddc access types for standalone self testing.
+ */
+typedef enum
+{
+	XHDCP22_RX_TEST_DDC_ACCESS_WO,  /**< Write-Only */
+	XHDCP22_RX_TEST_DDC_ACCESS_RO,  /**< Read-Only */
+	XHDCP22_RX_TEST_DDC_ACCESS_RW   /**< Read-Write */
+} XHdcp22_Rx_TestDdcAccess;
+
+/**
+ * These constants are the discrete event states for standalone self testing.
+ */
+typedef enum
+{
+	XHDCP22_RX_TEST_STATE_UNAUTHENTICATED          = 0xB00,
+	XHDCP22_RX_TEST_STATE_SEND_AKEINIT             = 0xB10,
+	XHDCP22_RX_TEST_STATE_WAIT_AKESENDCERT         = 0xB11,
+	XHDCP22_RX_TEST_STATE_SEND_AKENOSTOREDKM       = 0xB12,
+	XHDCP22_RX_TEST_STATE_SEND_AKESTOREDKM         = 0xB13,
+	XHDCP22_RX_TEST_STATE_WAIT_AKESENDHPRIME       = 0xB14,
+	XHDCP22_RX_TEST_STATE_WAIT_AKESENDPAIRING      = 0xB15,
+	XHDCP22_RX_TEST_STATE_SEND_LCINIT              = 0xB20,
+	XHDCP22_RX_TEST_STATE_WAIT_LCSENDLPRIME        = 0xB21,
+	XHDCP22_RX_TEST_STATE_SEND_SKESENDEKS          = 0xB30,
+	XHDCP22_RX_TEST_STATE_WAIT_AUTHENTICATED       = 0xB40,
+	XHDCP22_RX_TEST_STATE_UPDATE_TOPOLOGY          = 0xC40,
+	XHDCP22_RX_TEST_STATE_WAIT_RECEIVERIDLIST      = 0xC50,
+	XHDCP22_RX_TEST_STATE_SEND_RECEIVERIDLISTACK   = 0xC60,
+	XHDCP22_RX_TEST_STATE_SEND_STREAMMANAGEMENT    = 0xC70,
+	XHDCP22_RX_TEST_STATE_WAIT_STREAMREADY         = 0xC80,
+	XHDCP22_RX_TEST_STATE_WAIT_REAUTHREQ,
+	XHDCP22_RX_TEST_STATE_WAIT_REPEATERREADY
+} XHdcp22_Rx_TestState;
+
+/**
+ * This typedef is the RSA private key quintuple definition.
+ */
+typedef struct
+{
+	u8 p[64];
+	u8 q[64];
+	u8 dp[64];
+	u8 dq[64];
+	u8 qinv[64];
+} XHdcp22_Rx_KprivRx;
+
+/**
+ * This typedef is the RSA public key definition.
+ */
+typedef struct
+{
+	u8 N[128];
+	u8 e[3];
+} XHdcp22_Rx_KpubRx;
+
+/**
+ * This typedef is the DCP public certificate definition.
+ */
+typedef struct
+{
+	u8 ReceiverId[5];
+	u8 KpubRx[131];
+	u8 Reserved[2];
+	u8 Signature[384];
+} XHdcp22_Rx_CertRx;
+
+/**
+ * This typedef is the AKE_Init message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 Rtx[8];
+	u8 TxCaps[3];
+} XHdcp22_Rx_AKEInit;
+
+/**
+ * This typedef is the AKE_Send_Cert message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 CertRx[522];
+	u8 Rrx[8];
+	u8 RxCaps[3];
+} XHdcp22_Rx_AKESendCert;
+
+/**
+ * This typedef is the AKE_No_Stored_km message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 EKpubKm[128];
+} XHdcp22_Rx_AKENoStoredKm;
+
+/**
+ * This typedef is the AKE_Stored_km message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 EKhKm[16];
+	u8 M[16];
+} XHdcp22_Rx_AKEStoredKm;
+
+/**
+ * This typedef is the AKE_Send_H_prime message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 HPrime[32];
+} XHdcp22_Rx_AKESendHPrime;
+
+/**
+ * This typedef is the AKE_Send_Pairing_Info message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 EKhKm[16];
+} XHdcp22_Rx_AKESendPairingInfo;
+
+/**
+ * This typedef is the LC_Init message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 Rn[8];
+} XHdcp22_Rx_LCInit;
+
+/**
+ * This typdef is the LC_Send_L_prime message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 LPrime[32];
+} XHdcp22_Rx_LCSendLPrime;
+
+/**
+ * This typedef is the SKE_Send_Eks message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 EDkeyKs[16];
+	u8 Riv[8];
+} XHdcp22_Rx_SKESendEks;
+
+/**
+ * This typedef is the RepeaterAuth_Send_RceiverID_List message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 RxInfo[2];
+	u8 SeqNumV[3];
+	u8 VPrime[16];
+	u8 ReceiverIdList[5*31];
+} XHdcp22_Rx_RepeaterAuthSendRxIdList;
+
+/**
+ * This typedef is the RepeaterAuth_Send_Ack message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 V[16];
+} XHdcp22_Rx_RepeaterAuthSendAck;
+
+/**
+ * This typedef is the RepeaterAuth_Stream_Manage message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 SeqNumM[3];
+	u8 K[2];
+	u8 StreamIdType[2];
+} XHdcp22_Rx_RepeaterAuthStreamManage;
+
+/**
+ * This typedef is the RepeaterAuth_Stream_Ready message definition.
+ */
+typedef struct
+{
+	u8 MsgId;
+	u8 MPrime[32];
+} XHdcp22_Rx_RepeaterAuthStreamReady;
+
+/**
+ * This typedef is the union of all the message types.
+ */
+typedef union
+{
+	u8 MsgId;
+	XHdcp22_Rx_AKEInit            		AKEInit;
+	XHdcp22_Rx_AKESendCert        		AKESendCert;
+	XHdcp22_Rx_AKENoStoredKm      		AKENoStoredKm;
+	XHdcp22_Rx_AKEStoredKm        		AKEStoredKm;
+	XHdcp22_Rx_AKESendHPrime      		AKESendHPrime;
+	XHdcp22_Rx_AKESendPairingInfo 		AKESendPairingInfo;
+	XHdcp22_Rx_LCInit					LCInit;
+	XHdcp22_Rx_LCSendLPrime       		LCSendLPrime;
+	XHdcp22_Rx_SKESendEks         		SKESendEks;
+	XHdcp22_Rx_RepeaterAuthSendRxIdList	RepeaterAuthSendRxIdList;
+	XHdcp22_Rx_RepeaterAuthSendAck		RepeaterAuthSendAck;
+	XHdcp22_Rx_RepeaterAuthStreamManage	RepeaterAuthStreamManage;
+	XHdcp22_Rx_RepeaterAuthStreamReady	RepeaterAuthStreamReady;
+} XHdcp22_Rx_Message;
+
+/***************** Macros (Inline Functions) Definitions ********************/
+
+/************************** Function Prototypes *****************************/
+
+/* Crypto Functions */
+int  XHdcp22Rx_CalcMontNPrime(u8 *NPrime, const u8 *N, int NDigits);
+void XHdcp22Rx_GenerateRandom(XHdcp22_Rx *InstancePtr, int NumOctets, u8* RandomNumberPtr);
+int  XHdcp22Rx_RsaesOaepEncrypt(const XHdcp22_Rx_KpubRx *KpubRx, const u8 *Message,
+			const u32 MessageLen, const u8 *MaskingSeed, u8 *EncryptedMessage);
+int  XHdcp22Rx_RsaesOaepDecrypt(XHdcp22_Rx *InstancePtr, const XHdcp22_Rx_KprivRx *KprivRx,
+			 u8 *EncryptedMessage, u8 *Message, int *MessageLen);
+void XHdcp22Rx_ComputeHPrime(const u8* Rrx, const u8 *RxCaps, const u8* Rtx,
+	     const u8 *TxCaps, const u8 *Km, u8 *HPrime);
+void XHdcp22Rx_ComputeEkh(const u8 *KprivRx, const u8 *Km, const u8 *M, u8 *Ekh);
+void XHdcp22Rx_ComputeLPrime(const u8 *Rn, const u8 *Km, const u8 *Rrx, const u8 *Rtx, u8 *LPrime);
+void XHdcp22Rx_ComputeKs(const u8* Rrx, const u8* Rtx, const u8 *Km, const u8 *Rn,
+			 const u8 *Eks, u8 * Ks);
+void XHdcp22Rx_ComputeVPrime(const u8 *ReceiverIdList, u32 ReceiverIdListSize,
+       const u8 *RxInfo, const u8 *SeqNumV, const u8 *Km, const u8 *Rrx,
+       const u8 *Rtx, u8 *VPrime);
+void XHdcp22Rx_ComputeMPrime(const u8 *StreamIdType, const u8 *SeqNumM,
+       const u8 *Km, const u8 *Rrx, const u8 *Rtx, u8 *MPrime);
+
+#ifdef _XHDCP22_RX_TEST_
+/* External functions used for self-testing */
+int  XHdcp22Rx_TestSetMode(XHdcp22_Rx *InstancePtr, XHdcp22_Rx_TestMode TestMode,
+			 XHdcp22_Rx_TestFlags TestVectorFlag);
+int  XHdcp22Rx_TestRun(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_TestIsFinished(XHdcp22_Rx *InstancePtr);
+u8   XHdcp22Rx_TestIsPassed(XHdcp22_Rx *InstancePtr);
+int  XHdcp22Rx_TestLoadKeys(XHdcp22_Rx *InstancePtr);
+void XHdcp22Rx_TestSetVerbose(XHdcp22_Rx *InstancePtr, u8 Verbose);
+
+/* Internal functions used for self-testing */
+int  XHdcp22Rx_TestDdcWriteReg(XHdcp22_Rx *InstancePtr, u8 DeviceAddress, int Size, u8 *Data, u8 Stop);
+int  XHdcp22Rx_TestDdcReadReg(XHdcp22_Rx *InstancePtr, u8 DeviceAddress, int Size, u8 *Data, u8 Stop);
+void XHdcp22Rx_TestGenerateRrx(XHdcp22_Rx *InstancePtr, u8* RrxPtr);
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDCP22_RX_I_H_ */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_rx_sinit.c
@@ -0,0 +1,91 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+* @file xhdcp22_rx_sinit.c
+* @{
+* @details
+*
+* This file contains static initialization method for Xilinx HDCP 2.2 Receiver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00  MH   10/30/15 First Release
+*</pre>
+*
+*****************************************************************************/
+
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp22_rx.h"
+
+
+/************************** Constant Definitions *****************************/
+#ifndef XPAR_XHDCP22_RX_NUM_INSTANCES
+#define XPAR_XHDCP22_RX_NUM_INSTANCES  0
+#endif
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+/************************** Variable Definitions *****************************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XHdcp22_Rx_Config structure based
+* on the core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xhdcp22_rx_g.c file.
+*
+* @param	DeviceId is the unique core ID of the HDCP RX core for the
+*			lookup operation.
+*
+* @return	XHdcp22Rx_LookupConfig returns a reference to a config record
+*			in the configuration table (in xhdmi_tx_g.c) corresponding
+*			to <i>DeviceId</i>, or NULL if no match is found.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdcp22_Rx_Config *XHdcp22Rx_LookupConfig(u16 DeviceId)
+{
+	extern XHdcp22_Rx_Config XHdcp22_Rx_ConfigTable[XPAR_XHDCP22_RX_NUM_INSTANCES];
+	XHdcp22_Rx_Config *CfgPtr = NULL;
+	u32 Index;
+
+	/* Checking for device id for which instance it is matching */
+	for (Index = (u32)0x0; Index < (u32)(XPAR_XHDCP22_RX_NUM_INSTANCES); Index++) {
+		/* Assigning address of config table if both device ids
+		 * are matched
+		 */
+		if (XHdcp22_Rx_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XHdcp22_Rx_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return CfgPtr;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx.c
@@ -0,0 +1,4581 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_tx.c
+* @{
+* @details
+*
+* This file contains the main implementation of the Xilinx HDCP 2.2 Transmitter
+* device driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- -------------------------------------------------------
+* 1.00  JO     06/24/15 Initial release.
+* 1.01  MH     01/15/16 Replaced function XHdcp22Tx_SetDdcHandles with
+*                       XHdcp22Tx_SetCallback. Removed test directives.
+* 1.02  MG     02/25/16 Added authenticated callback and GetVersion.
+* 1.03  MG     02/29/16 Added XHdcp22Cipher_Disable in function XHdcp22Tx_Reset.
+* 1.04  MH     03/14/16 Updated StateA5 to check re-authentication request
+*                       before enabling the cipher.
+* 2.00  MH     06/28/16 Updated for repeater downstream support.
+* 2.01  MH     02/13/17 1. Fixed function XHdcp22Tx_IsInProgress to correctly
+*                          return TRUE while state machine is executing.
+*                       2. Fixed checking of seq_num_V for topology propagation.
+*                       3. Updated state A0 to set 100ms timer before sending
+*                          AKE_Init message to ensure encryption is disabled.
+*                       4. Fixed function XHdcp22Tx_UpdatePairingInfo to check
+*                          for empty slots before overriding entry.
+*                       5. Fixed problem with pairing table update that was
+*                          causing corrupted entries.
+*                       6. Update to check return status of DDC read/write.
+*                       7. Fixed compiler warnings.
+* 2.20  MH     04/12/17 Added function XHdcp22Tx_IsDwnstrmCapable.
+* 2.30  MH     07/06/17 1. Updated for 64 bit ARM support.
+*                       2. Added HDCP2Capable check for re-authentication
+*                       3. Update cipher enablement
+*                       4. Fix in XHdcp22Tx_WaitForReceiver to poll RxStatus
+*                          based on fixed interval.
+*                       5. Fix in XHdcp22Tx_WaitForReceiver to wait for READY
+*                          and non-zero Message_Size before reading message
+*                          buffer.
+*                       6. Check return status of DDC write/read when polling
+*                          RxStatus register.
+* 2.31  YB     03/28/19 Moved the reading of the DDC status from
+*                          XHdcp22Tx_TimerHandler to XHdcp22Tx_Poll.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_tx.h"
+#include "xhdcp22_tx_i.h"
+#include "xil_printf.h"
+
+/************************** Constant Definitions *****************************/
+
+/** RxStatus value used to force re-authentication */
+#define XHDCP22_TX_INVALID_RXSTATUS 0xFFFF
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/** Case replacement to copy a case Id to a string with a pre-lead */
+#define XHDCP22_TX_CASE_TO_STR_PRE(pre, arg) \
+case pre ## arg : strcpy(str, #arg); break;
+
+/**************************** Type Definitions *******************************/
+/**
+* Pointer to the state handling functions
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return The next state that should be executed.
+*
+* @note   None.
+*
+*/
+typedef XHdcp22_Tx_StateType XHdcp22Tx_StateFuncType(XHdcp22_Tx *InstancePtr);
+
+/**
+* Pointer to the transition functions going from one state to the next.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+*/
+typedef void XHdcp22_Tx_TransitionFuncType(XHdcp22_Tx *InstancePtr);
+
+/************************** Function Prototypes ******************************/
+
+/* Initialization of peripherals */
+static int XHdcp22Tx_InitializeTimer(XHdcp22_Tx *InstancePtr);
+static int XHdcp22Tx_InitializeCipher(XHdcp22_Tx *InstancePtr);
+static int XHdcp22Tx_InitializeRng(XHdcp22_Tx *InstancePtr);
+static int XHdcp22Tx_ComputeBaseAddress(UINTPTR BaseAddress, UINTPTR SubcoreOffset, UINTPTR *SubcoreAddressPtr);
+
+/* Stubs for callbacks */
+static int XHdcp22Tx_StubDdc(u8 DeviceAddress, u16 ByteCount, u8* BufferPtr,
+                             u8 Stop, void *RefPtr);
+static void XHdcp22Tx_StubCallback(void* RefPtr);
+
+/* state handling  functions */
+static XHdcp22_Tx_StateType XHdcp22Tx_StateH0(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateH1(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA0(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA1(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_1(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_Nsk0(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_Nsk1(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_Sk0(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA2(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA2_1(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA3(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA4(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA5(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA6_A7_A8(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA6(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA7(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA8(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA9(XHdcp22_Tx *InstancePtr);
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA9_1(XHdcp22_Tx *InstancePtr);
+
+/* State transition handling functions are used to do initial code before
+* entering a new state. This is used in cases that a state is executed
+* repeatedly due to the polling mechanism. A state transisition ensures in
+* this case that the code is executed only once during authentication.
+*/
+static void XHdcp22Tx_A1A0(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A1A2(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A2A0(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A3A0(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A3A4(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A4A5(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A6A7A0(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_A9A0(XHdcp22_Tx *InstancePtr);
+
+/* Protocol specific functions */
+static int XHdcp22Tx_WriteAKEInit(XHdcp22_Tx *InstancePtr);
+static int XHdcp22Tx_WriteAKENoStoredKm(XHdcp22_Tx *InstancePtr,
+                    const XHdcp22_Tx_PairingInfo *PairingInfoPtr,
+                    const XHdcp22_Tx_CertRx *CertificatePtr);
+static int XHdcp22Tx_WriteAKEStoredKm(XHdcp22_Tx *InstancePtr,
+                    const XHdcp22_Tx_PairingInfo *PairingInfoPtr);
+static int XHdcp22Tx_WriteLcInit(XHdcp22_Tx *InstancePtr, const u8 *Rn);
+static int XHdcp22Tx_WriteSkeSendEks(XHdcp22_Tx *InstancePtr,
+                    const u8 *EdkeyKsPtr, const u8 *RivPtr);
+static int XHdcp22Tx_WriteRepeaterAuth_Send_Ack(XHdcp22_Tx *InstancePtr, const u8 *V);
+static int XHdcp22Tx_WriteRepeaterAuth_Stream_Manage(XHdcp22_Tx *InstancePtr);
+static int XHdcp22Tx_ReceiveMsg(XHdcp22_Tx *InstancePtr, u8 MessageId,
+                    u32 MessageSize);
+
+/* Generators and functions that return a generated value or a testvector */
+static void XHdcp22Tx_GenerateRtx(XHdcp22_Tx *InstancePtr, u8* RtxPtr);
+static void XHdcp22Tx_GenerateKm(XHdcp22_Tx *InstancePtr, u8* KmPtr);
+static void XHdcp22Tx_GenerateKmMaskingSeed(XHdcp22_Tx *InstancePtr, u8* SeedPtr);
+static void XHdcp22Tx_GenerateRn(XHdcp22_Tx *InstancePtr, u8* RnPtr);
+static void XHdcp22Tx_GenerateRiv(XHdcp22_Tx *InstancePtr, u8* RivPtr);
+static void XHdcp22Tx_GenerateKs(XHdcp22_Tx *InstancePtr, u8* KsPtr);
+static const u8* XHdcp22Tx_GetKPubDpc(XHdcp22_Tx *InstancePtr);
+
+/* Cryptographic functions */
+static XHdcp22_Tx_PairingInfo *XHdcp22Tx_GetPairingInfo(XHdcp22_Tx *InstancePtr,
+                                                        const u8 *ReceiverId);
+static void XHdcp22Tx_InvalidatePairingInfo(XHdcp22_Tx *InstancePtr,
+                                             const u8* ReceiverId);
+static XHdcp22_Tx_PairingInfo *XHdcp22Tx_UpdatePairingInfo(XHdcp22_Tx *InstancePtr,
+                              const XHdcp22_Tx_PairingInfo *PairingInfo, u8 Ready);
+
+/* Timer functions */
+static void XHdcp22Tx_TimerHandler(void *CallbackRef, u8 TmrCntNumber);
+static int XHdcp22Tx_StartTimer(XHdcp22_Tx *InstancePtr, u32 TimeOut_mSec,
+                                u8 ReasonId);
+static int XHdcp22Tx_WaitForReceiver(XHdcp22_Tx *InstancePtr, int ExpectedSize, u8 ReadyBit);
+static u32 XHdcp22Tx_GetTimerCount(XHdcp22_Tx *InstancePtr);
+
+/* RxStatus handling */
+static void XHdcp22Tx_ReadRxStatus(XHdcp22_Tx *InstancePtr);
+
+/* Status handling */
+static void XHdcp22Tx_HandleAuthenticationFailed(XHdcp22_Tx *InstancePtr);
+static void XHdcp22Tx_HandleReauthenticationRequest(XHdcp22_Tx * InstancePtr);
+
+/* Function for setting fields inside the topology structure */
+static u32 XHdcp22Tx_GetTopologyDepth(XHdcp22_Tx *InstancePtr);
+static u32 XHdcp22Tx_GetTopologyDeviceCnt(XHdcp22_Tx *InstancePtr);
+static u32 XHdcp22Tx_GetTopologyMaxDevsExceeded(XHdcp22_Tx *InstancePtr);
+static u32 XHdcp22Tx_GetTopologyMaxCascadeExceeded(XHdcp22_Tx *InstancePtr);
+static u32 XHdcp22Tx_GetTopologyHdcp2LegacyDeviceDownstream(XHdcp22_Tx *InstancePtr);
+static u32 XHdcp22Tx_GetTopologyHdcp1DeviceDownstream(XHdcp22_Tx *InstancePtr);
+
+/************************** Variable Definitions *****************************/
+
+/**
+* This table contains the function pointers for all possible states.
+* The order of elements must match the #XHdcp22_Tx_StateType enumerator definitions.
+*/
+XHdcp22Tx_StateFuncType* const XHdcp22_Tx_StateTable[XHDCP22_TX_NUM_STATES] =
+{
+	XHdcp22Tx_StateH0, XHdcp22Tx_StateH1, XHdcp22Tx_StateA0,
+	XHdcp22Tx_StateA1, Xhdcp22Tx_StateA1_1,
+	Xhdcp22Tx_StateA1_Nsk0, Xhdcp22Tx_StateA1_Nsk1, Xhdcp22Tx_StateA1_Sk0,
+	XHdcp22Tx_StateA2, XHdcp22Tx_StateA2_1,
+	XHdcp22Tx_StateA3, XHdcp22Tx_StateA4, XHdcp22Tx_StateA5,
+	XHdcp22Tx_StateA6_A7_A8,
+	XHdcp22Tx_StateA6, XHdcp22Tx_StateA7, XHdcp22Tx_StateA8, XHdcp22Tx_StateA9, XHdcp22Tx_StateA9_1
+};
+
+/**
+* This table is a matrix that contains the function pointers for functions to execute on
+* state transition.
+* It is filled dynamically.
+* A NULL value is used if no transition is required.
+*/
+static XHdcp22_Tx_TransitionFuncType * transition_table[XHDCP22_TX_NUM_STATES][XHDCP22_TX_NUM_STATES];
+
+/* public transmitter DCP LLC key - n=384 bytes, e=1 byte */
+static const u8 XHdcp22_Tx_KpubDcp[XHDCP22_TX_KPUB_DCP_LLC_N_SIZE + XHDCP22_TX_KPUB_DCP_LLC_E_SIZE] = {
+	0xB0, 0xE9, 0xAA, 0x45, 0xF1, 0x29, 0xBA, 0x0A, 0x1C, 0xBE, 0x17, 0x57, 0x28, 0xEB, 0x2B, 0x4E,
+	0x8F, 0xD0, 0xC0, 0x6A, 0xAD, 0x79, 0x98, 0x0F, 0x8D, 0x43, 0x8D, 0x47, 0x04, 0xB8, 0x2B, 0xF4,
+	0x15, 0x21, 0x56, 0x19, 0x01, 0x40, 0x01, 0x3B, 0xD0, 0x91, 0x90, 0x62, 0x9E, 0x89, 0xC2, 0x27,
+	0x8E, 0xCF, 0xB6, 0xDB, 0xCE, 0x3F, 0x72, 0x10, 0x50, 0x93, 0x8C, 0x23, 0x29, 0x83, 0x7B, 0x80,
+	0x64, 0xA7, 0x59, 0xE8, 0x61, 0x67, 0x4C, 0xBC, 0xD8, 0x58, 0xB8, 0xF1, 0xD4, 0xF8, 0x2C, 0x37,
+	0x98, 0x16, 0x26, 0x0E, 0x4E, 0xF9, 0x4E, 0xEE, 0x24, 0xDE, 0xCC, 0xD1, 0x4B, 0x4B, 0xC5, 0x06,
+	0x7A, 0xFB, 0x49, 0x65, 0xE6, 0xC0, 0x00, 0x83, 0x48, 0x1E, 0x8E, 0x42, 0x2A, 0x53, 0xA0, 0xF5,
+	0x37, 0x29, 0x2B, 0x5A, 0xF9, 0x73, 0xC5, 0x9A, 0xA1, 0xB5, 0xB5, 0x74, 0x7C, 0x06, 0xDC, 0x7B,
+	0x7C, 0xDC, 0x6C, 0x6E, 0x82, 0x6B, 0x49, 0x88, 0xD4, 0x1B, 0x25, 0xE0, 0xEE, 0xD1, 0x79, 0xBD,
+	0x39, 0x85, 0xFA, 0x4F, 0x25, 0xEC, 0x70, 0x19, 0x23, 0xC1, 0xB9, 0xA6, 0xD9, 0x7E, 0x3E, 0xDA,
+	0x48, 0xA9, 0x58, 0xE3, 0x18, 0x14, 0x1E, 0x9F, 0x30, 0x7F, 0x4C, 0xA8, 0xAE, 0x53, 0x22, 0x66,
+	0x2B, 0xBE, 0x24, 0xCB, 0x47, 0x66, 0xFC, 0x83, 0xCF, 0x5C, 0x2D, 0x1E, 0x3A, 0xAB, 0xAB, 0x06,
+	0xBE, 0x05, 0xAA, 0x1A, 0x9B, 0x2D, 0xB7, 0xA6, 0x54, 0xF3, 0x63, 0x2B, 0x97, 0xBF, 0x93, 0xBE,
+	0xC1, 0xAF, 0x21, 0x39, 0x49, 0x0C, 0xE9, 0x31, 0x90, 0xCC, 0xC2, 0xBB, 0x3C, 0x02, 0xC4, 0xE2,
+	0xBD, 0xBD, 0x2F, 0x84, 0x63, 0x9B, 0xD2, 0xDD, 0x78, 0x3E, 0x90, 0xC6, 0xC5, 0xAC, 0x16, 0x77,
+	0x2E, 0x69, 0x6C, 0x77, 0xFD, 0xED, 0x8A, 0x4D, 0x6A, 0x8C, 0xA3, 0xA9, 0x25, 0x6C, 0x21, 0xFD,
+	0xB2, 0x94, 0x0C, 0x84, 0xAA, 0x07, 0x29, 0x26, 0x46, 0xF7, 0x9B, 0x3A, 0x19, 0x87, 0xE0, 0x9F,
+	0xEB, 0x30, 0xA8, 0xF5, 0x64, 0xEB, 0x07, 0xF1, 0xE9, 0xDB, 0xF9, 0xAF, 0x2C, 0x8B, 0x69, 0x7E,
+	0x2E, 0x67, 0x39, 0x3F, 0xF3, 0xA6, 0xE5, 0xCD, 0xDA, 0x24, 0x9B, 0xA2, 0x78, 0x72, 0xF0, 0xA2,
+	0x27, 0xC3, 0xE0, 0x25, 0xB4, 0xA1, 0x04, 0x6A, 0x59, 0x80, 0x27, 0xB5, 0xDA, 0xB4, 0xB4, 0x53,
+	0x97, 0x3B, 0x28, 0x99, 0xAC, 0xF4, 0x96, 0x27, 0x0F, 0x7F, 0x30, 0x0C, 0x4A, 0xAF, 0xCB, 0x9E,
+	0xD8, 0x71, 0x28, 0x24, 0x3E, 0xBC, 0x35, 0x15, 0xBE, 0x13, 0xEB, 0xAF, 0x43, 0x01, 0xBD, 0x61,
+	0x24, 0x54, 0x34, 0x9F, 0x73, 0x3E, 0xB5, 0x10, 0x9F, 0xC9, 0xFC, 0x80, 0xE8, 0x4D, 0xE3, 0x32,
+	0x96, 0x8F, 0x88, 0x10, 0x23, 0x25, 0xF3, 0xD3, 0x3E, 0x6E, 0x6D, 0xBB, 0xDC, 0x29, 0x66, 0xEB,
+	0x03
+};
+
+
+/**
+* This array contains the capabilities of the HDCP22 TX core, and is transmitted during
+* authentication as part of the AKE_Init message.
+*/
+static const u8 XHdcp22_Tx_TxCaps[] = { 0x02, 0x00, 0x00 };
+
+
+/************************** Function Definitions *****************************/
+/*****************************************************************************/
+/**
+*
+* This function initializes the HDCP22 TX core. This function must be called
+* prior to using the HDCP TX core. Initialization of the HDCP TX includes
+* setting up the instance data and ensuring the hardware is in a quiescent
+* state.
+*
+* @param InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param CfgPtr points to the configuration structure associated with
+*        the HDCP TX core.
+* @param EffectiveAddr is the base address of the device. If address
+*        translation is being used, then this parameter must reflect the
+*        virtual base address. Otherwise, the physical address should be
+*        used.
+*
+* @return
+*    - XST_SUCCESS Initialization was successful.
+*    - XST_FAILURE Initialization of the internal timer failed or there was a
+*               HDCP TX PIO ID mismatch.
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_CfgInitialize(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_Config *CfgPtr,
+                            UINTPTR EffectiveAddr)
+{
+	int Result = XST_SUCCESS;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+	Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+	/* Setup the instance */
+	(void)memset((void *)InstancePtr, 0, sizeof(XHdcp22_Tx));
+
+	/* copy configuration settings */
+	(void)memcpy((void *)&(InstancePtr->Config), (const void *)CfgPtr,
+				 sizeof(XHdcp22_Tx_Config));
+
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+
+	/* Set all handlers to stub values, let user configure this data later */
+	InstancePtr->DdcRead = XHdcp22Tx_StubDdc;
+	InstancePtr->IsDdcReadSet = (FALSE);
+	InstancePtr->DdcWrite = XHdcp22Tx_StubDdc;
+	InstancePtr->IsDdcWriteSet = (FALSE);
+	InstancePtr->AuthenticatedCallback = XHdcp22Tx_StubCallback;
+	InstancePtr->IsAuthenticatedCallbackSet = (FALSE);
+	InstancePtr->UnauthenticatedCallback = XHdcp22Tx_StubCallback;
+	InstancePtr->IsUnauthenticatedCallbackSet = (FALSE);
+	InstancePtr->DownstreamTopologyAvailableCallback = XHdcp22Tx_StubCallback;
+	InstancePtr->IsDownstreamTopologyAvailableCallbackSet = (FALSE);
+
+	InstancePtr->Info.Protocol = XHDCP22_TX_HDMI;
+
+	/* Initialize global parameters */
+	InstancePtr->Info.IsReceiverHDCP2Capable = (FALSE);
+
+	/* Initialize statemachine, but do not run it */
+	/* Dynamically setup the transition table */
+	memset(transition_table, 0x00, sizeof(transition_table));
+	transition_table[XHDCP22_TX_STATE_A1][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A1A0;
+	transition_table[XHDCP22_TX_STATE_A1_1][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A1A0;
+	transition_table[XHDCP22_TX_STATE_A1_NSK0][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A1A0;
+	transition_table[XHDCP22_TX_STATE_A1_NSK1][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A1A0;
+	transition_table[XHDCP22_TX_STATE_A1_SK0][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A1A0;
+
+	transition_table[XHDCP22_TX_STATE_A1_NSK1][XHDCP22_TX_STATE_A2] = XHdcp22Tx_A1A2;
+	transition_table[XHDCP22_TX_STATE_A1_SK0][XHDCP22_TX_STATE_A2] = XHdcp22Tx_A1A2;
+
+	transition_table[XHDCP22_TX_STATE_A2][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A2A0;
+	transition_table[XHDCP22_TX_STATE_A2_1][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A2A0;
+	transition_table[XHDCP22_TX_STATE_A3][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A3A0;
+	transition_table[XHDCP22_TX_STATE_A4][XHDCP22_TX_STATE_A5] = XHdcp22Tx_A4A5;
+	transition_table[XHDCP22_TX_STATE_A3][XHDCP22_TX_STATE_A4] = XHdcp22Tx_A3A4;
+	transition_table[XHDCP22_TX_STATE_A6_A7_A8][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A6A7A0;
+	transition_table[XHDCP22_TX_STATE_A9][XHDCP22_TX_STATE_A0] = XHdcp22Tx_A9A0;
+
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_UNAUTHENTICATED;
+	InstancePtr->Info.CurrentState = XHDCP22_TX_STATE_H0;
+	InstancePtr->Info.PrvState = XHDCP22_TX_STATE_H0;
+	InstancePtr->Info.IsEnabled = (FALSE);
+	InstancePtr->Info.StateContext = NULL;
+	InstancePtr->Info.MsgAvailable = (FALSE);
+	InstancePtr->Info.PollingValue = XHDCP22_TX_DEFAULT_RX_STATUS_POLLVALUE;
+
+	/* Topology info */
+	InstancePtr->Info.IsTopologyAvailable = (FALSE);
+
+	/* Timer configuration */
+	InstancePtr->Timer.TimerExpired = (TRUE);
+	InstancePtr->Timer.ReasonId = XHDCP22_TX_TS_UNDEFINED;
+	InstancePtr->Timer.InitialTicks = 0;
+
+	/* Receiver ID list */
+	InstancePtr->Info.ReceivedFirstSeqNum_V = (FALSE);
+
+	/* Revocation List */
+	InstancePtr->Info.IsRevocationListValid = (FALSE);
+	InstancePtr->RevocationList.NumDevices = 0;
+
+	/* Content Stream Management */
+	InstancePtr->Info.ContentStreamType = XHDCP22_STREAMTYPE_0; // Default
+	InstancePtr->Info.IsContentStreamTypeSet = (TRUE);
+
+	/* Clear pairing info */
+	XHdcp22Tx_ClearPairingInfo(InstancePtr);
+
+	/* Initialize hardware timer */
+	Result = XHdcp22Tx_InitializeTimer(InstancePtr);
+	if (Result != XST_SUCCESS) {
+		return Result;
+	}
+
+	/* Initialize random number generator */
+	Result = XHdcp22Tx_InitializeRng(InstancePtr);
+	if (Result != XST_SUCCESS) {
+		return Result;
+	}
+
+	/* Initialize cipher */
+	Result = XHdcp22Tx_InitializeCipher(InstancePtr);
+	if (Result != XST_SUCCESS) {
+		return Result;
+	}
+
+	/* Indicate the instance is now ready to use, initialized without error */
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+
+	XHdcp22Tx_LogReset(InstancePtr, FALSE);
+
+	return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a called to initialize the hardware timer.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*    - XST_SUCCESS if authenticated is started successfully.
+*    - XST_FAIL if the state machine is disabled.
+*
+* @note  None.
+*
+******************************************************************************/
+static int XHdcp22Tx_InitializeTimer(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	UINTPTR SubcoreBaseAddr;
+
+	int Result = XST_SUCCESS;
+
+	XTmrCtr_Config *TimerConfigPtr;
+
+	TimerConfigPtr = XTmrCtr_LookupConfig(InstancePtr->Config.TimerDeviceId);
+	if(TimerConfigPtr == NULL) {
+		return XST_FAILURE;
+	}
+
+	Result = XHdcp22Tx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, TimerConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	XTmrCtr_CfgInitialize(&InstancePtr->Timer.TmrCtr, TimerConfigPtr, SubcoreBaseAddr);
+	if (Result != XST_SUCCESS) {
+		return Result;
+	}
+
+	XTmrCtr_SetOptions(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0,
+	                   XTC_INT_MODE_OPTION | XTC_DOWN_COUNT_OPTION);
+	XTmrCtr_SetOptions(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_1,
+	                   XTC_AUTO_RELOAD_OPTION);
+	XTmrCtr_SetHandler(&InstancePtr->Timer.TmrCtr, XHdcp22Tx_TimerHandler,
+	                   InstancePtr);
+	return Result;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a called to initialize the cipher.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*    - XST_SUCCESS if authenticated is started successfully.
+*    - XST_FAIL if the state machine is disabled.
+*
+* @note  None.
+*
+******************************************************************************/
+static int XHdcp22Tx_InitializeCipher(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Result = XST_SUCCESS;
+
+	XHdcp22_Cipher_Config *ConfigPtr = NULL;
+	UINTPTR SubcoreBaseAddr;
+
+	ConfigPtr = XHdcp22Cipher_LookupConfig(InstancePtr->Config.CipherId);
+	if (ConfigPtr == NULL) {
+		return XST_DEVICE_NOT_FOUND;
+	}
+
+	Result = XHdcp22Tx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, ConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	Result |= XHdcp22Cipher_CfgInitialize(&InstancePtr->Cipher, ConfigPtr, SubcoreBaseAddr);
+	if (Result != XST_SUCCESS) {
+		return Result;
+	}
+
+	/* Set cipher to TX mode */
+	XHdcp22Cipher_SetTxMode(&InstancePtr->Cipher);
+
+	/* Disable encryption */
+	XHdcp22Tx_DisableEncryption(InstancePtr);
+
+	/* Disable cipher */
+	XHdcp22Cipher_Disable(&InstancePtr->Cipher);
+
+	return Result;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a called to initialize the hardware random generator.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*    - XST_SUCCESS if authenticated is started successfully.
+*    - XST_FAIL if the state machine is disabled.
+*
+* @note  None.
+*
+******************************************************************************/
+static int XHdcp22Tx_InitializeRng(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	int Result = XST_SUCCESS;
+	UINTPTR SubcoreBaseAddr;
+
+	XHdcp22_Rng_Config *ConfigPtr = NULL;
+
+	ConfigPtr = XHdcp22Rng_LookupConfig(InstancePtr->Config.RngId);
+	if (ConfigPtr == NULL) {
+		return XST_DEVICE_NOT_FOUND;
+	}
+
+	Result = XHdcp22Tx_ComputeBaseAddress(InstancePtr->Config.BaseAddress, ConfigPtr->BaseAddress, &SubcoreBaseAddr);
+	Result |= XHdcp22Rng_CfgInitialize(&InstancePtr->Rng, ConfigPtr, SubcoreBaseAddr);
+	if (Result != XST_SUCCESS) {
+		return Result;
+	}
+	XHdcp22Rng_Enable(&InstancePtr->Rng);
+	return Result;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is used to load the Lc128 value by copying the contents
+* of the array referenced by Lc128Ptr into the cipher.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param	Lc128Ptr is a pointer to an array.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdcp22Tx_LoadLc128(XHdcp22_Tx *InstancePtr, const u8 *Lc128Ptr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Lc128Ptr != NULL);
+
+	XHdcp22Cipher_SetLc128(&InstancePtr->Cipher, Lc128Ptr,
+	                       XHDCP22_TX_LC128_SIZE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is used to load the system renewability messages (SRMs)
+* which carries the Receiver ID revocation list.
+*
+* @param	InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param	SrmPtr is a pointer to an array.
+*
+* @return
+*    - XST_SUCCESS if loaded SRM successfully.
+*    - XST_FAILURE if SRM signature verification failed.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdcp22Tx_LoadRevocationTable(XHdcp22_Tx *InstancePtr, const u8 *SrmPtr)
+{
+	int Result;
+	const u8* KPubDpcPtr = NULL;
+	const u8* SrmBlockPtr = NULL;
+	u8 SrmId;
+	u16 SrmVersion;
+	u8 SrmGenNr;
+	u32 BlockSize;
+	u32 LengthField;
+	u16 NumDevices;
+	const u8* ReceiverIdPtr;
+	XHdcp22_Tx_RevocationList* RevocationListPtr = NULL;
+	int i, j;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(SrmPtr != NULL);
+
+	SrmBlockPtr = SrmPtr;
+
+	/* byte 1 contains the SRM ID and HDCP2 Indicator field */
+	SrmId = SrmBlockPtr[0];
+	if (SrmId != 0x91) {
+		/* Unknown SRM ID so ignore the SRM */
+		return XST_FAILURE;
+	}
+
+	/* byte 2 is reserved */
+
+	/* byte 3-4 contain the SRM Version.
+	 * Value is in big endian format, Microblaze is little endian */
+	SrmVersion  = SrmBlockPtr[2] << 8; // MSB
+	SrmVersion |= SrmBlockPtr[3];      // LSB
+
+	/* byte 5 contains the SRM Generation Number */
+	SrmGenNr = SrmBlockPtr[4];
+
+	/* byte 6,7,8 contain the length of the first-generation SRM in bytes.
+	 * Value is in big endian format, Microblaze is little endian */
+	LengthField  = SrmBlockPtr[5] << 16; // MSB
+	LengthField |= SrmBlockPtr[6] << 8;
+	LengthField |= SrmBlockPtr[7];       // LSB
+
+	/* The size of the first-generation SRM block */
+	BlockSize = LengthField + 5;
+
+	KPubDpcPtr = XHdcp22Tx_GetKPubDpc(InstancePtr);
+
+	/* Verify the first-generation SRM block */
+	Result = XHdcp22Tx_VerifySRM(SrmBlockPtr,
+	                             BlockSize,
+	                             KPubDpcPtr, // N
+	                             XHDCP22_TX_KPUB_DCP_LLC_N_SIZE,
+	                             &KPubDpcPtr[XHDCP22_TX_KPUB_DCP_LLC_N_SIZE], // e
+	                             XHDCP22_TX_KPUB_DCP_LLC_E_SIZE);
+	if (Result != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Update the SRM Block pointer */
+	SrmBlockPtr += BlockSize;
+
+	for (i = 1; i < SrmGenNr; i++) {
+		/* byte 1-2 contain the length of the next-generation SRM in bytes.
+		 * Value is in big endian format, Microblaze is little endian */
+		LengthField  = SrmBlockPtr[0] << 8; // MSB
+		LengthField |= SrmBlockPtr[1];      // LSB
+
+		/* The size of the next-generation SRM block */
+		BlockSize = LengthField;
+
+		/* Verify the next-generation SRM block */
+		Result = XHdcp22Tx_VerifySRM(SrmBlockPtr,
+		                             BlockSize,
+		                             KPubDpcPtr, // N
+		                             XHDCP22_TX_KPUB_DCP_LLC_N_SIZE,
+		                             &KPubDpcPtr[XHDCP22_TX_KPUB_DCP_LLC_N_SIZE], // e
+		                             XHDCP22_TX_KPUB_DCP_LLC_E_SIZE);
+		if (Result != XST_SUCCESS) {
+			return XST_FAILURE;
+		}
+
+		/* Update the SRM Block pointer */
+		SrmBlockPtr += BlockSize;
+	}
+
+	/* SRM has been verified to be correct.
+	 * Now extract the revocation information */
+	SrmBlockPtr = SrmPtr;
+
+	/* byte 6,7,8 contain the length of the first-generation SRM in bytes.
+	 * Value is in big endian format, Microblaze is little endian */
+	LengthField  = SrmBlockPtr[5] << 16; // MSB
+	LengthField |= SrmBlockPtr[6] << 8;
+	LengthField |= SrmBlockPtr[7];       // LSB
+
+	/* The size of the first-generation SRM block */
+	BlockSize = LengthField + 5;
+
+	/* byte 9,10 contain the number of devices of the firs-generation SRM block
+	 * Value is in big endian format, Microblaze is little endian */
+	NumDevices  = SrmBlockPtr[8] << 2; // MSB
+	NumDevices |= SrmBlockPtr[9] >> 6; // LSB
+
+	RevocationListPtr = XHdcp22Tx_GetRevocationReceiverIdList(InstancePtr);
+	RevocationListPtr->NumDevices = 0;
+
+	/* byte 12 will contain the first byte of the first receiver ID */
+	ReceiverIdPtr = &SrmBlockPtr[12];
+
+	for (i = 0; i < NumDevices; i++) {
+		/* Is the revocation list full? */
+		if (RevocationListPtr->NumDevices == XHDCP22_TX_REVOCATION_LIST_MAX_DEVICES) {
+			return XST_FAILURE;
+		}
+
+		memcpy(RevocationListPtr->ReceiverId[RevocationListPtr->NumDevices], ReceiverIdPtr, XHDCP22_TX_SRM_RCVID_SIZE);
+		RevocationListPtr->NumDevices++;
+		ReceiverIdPtr += XHDCP22_TX_SRM_RCVID_SIZE;
+	}
+
+	/* Update the SRM Block pointer */
+	SrmBlockPtr += BlockSize;
+
+	for (j = 1; j < SrmGenNr; j++) {
+		/* byte 1-2 contain the length of the next-generation SRM in bytes.
+		 * Value is in big endian format, Microblaze is little endian */
+		LengthField  = SrmBlockPtr[0] << 8; // MSB
+		LengthField |= SrmBlockPtr[1];      // LSB
+
+		/* The size of the next-generation SRM block */
+		BlockSize = LengthField;
+
+		/* byte 3,4 contain the number of devices of the next-generation SRM block
+		 * Value is in big endian format, Microblaze is little endian */
+		NumDevices  = (SrmBlockPtr[2] & 0x3) << 8; // MSB
+		NumDevices |=  SrmBlockPtr[3]; // LSB
+
+		/* byte 5 will contain the first byte of the first receiver ID */
+		ReceiverIdPtr = &SrmBlockPtr[4];
+
+		for (i = 0; i < NumDevices; i++) {
+			/* Is the revocation list full? */
+			if (RevocationListPtr->NumDevices == XHDCP22_TX_REVOCATION_LIST_MAX_DEVICES) {
+				return XST_FAILURE;
+			}
+
+			memcpy(RevocationListPtr->ReceiverId[RevocationListPtr->NumDevices], ReceiverIdPtr, XHDCP22_TX_SRM_RCVID_SIZE);
+			RevocationListPtr->NumDevices++;
+			ReceiverIdPtr += XHDCP22_TX_SRM_RCVID_SIZE;
+		}
+
+		/* Update the SRM Block pointer */
+		SrmBlockPtr += BlockSize;
+	}
+
+	InstancePtr->Info.IsRevocationListValid = (TRUE);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function searches for the specified ReceiverID in the revocation list.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param    RecvIdPtr is a pointer to the ReceiverID to lookup
+*
+* @return
+*    - TRUE if Receiver ID was found in the revocation list
+*    - FALSE if Receiver ID was not found in the revocation list
+*
+* @note     None.
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsDeviceRevoked(XHdcp22_Tx *InstancePtr, u8 *RecvIdPtr)
+{
+	int Result;
+	u32 i;
+	XHdcp22_Tx_RevocationList* RevocationListPtr = NULL;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(RecvIdPtr != NULL);
+
+	RevocationListPtr = XHdcp22Tx_GetRevocationReceiverIdList(InstancePtr);
+
+	/* Loop over the revocation list */
+	for (i = 0; i < RevocationListPtr->NumDevices; i++) {
+		Result = memcmp(RecvIdPtr, RevocationListPtr->ReceiverId[i], XHDCP22_TX_SRM_RCVID_SIZE);
+		if (Result == 0)
+			return TRUE;
+	}
+	return FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pointer to the Revocation Receiver ID list.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx instance.
+*
+* @return Pointer to the XHdcp22_Tx_RevocationList instance.
+*
+******************************************************************************/
+XHdcp22_Tx_RevocationList* XHdcp22Tx_GetRevocationReceiverIdList(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return &InstancePtr->RevocationList;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pointer to the downstream topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   A pointer to the XHdcp22_Tx_Topology structure or NULL when
+*           the topology info is invalid.
+*
+* @note     None.
+*
+******************************************************************************/
+XHdcp22_Tx_Topology *XHdcp22Tx_GetTopology(XHdcp22_Tx *InstancePtr)
+{
+	if (InstancePtr->Info.IsTopologyAvailable)
+		return &InstancePtr->Topology;
+	else
+		return NULL;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pointer to the ReceiverID list in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   A pointer to the ReceiverID list in the topology structure.
+*
+* @note     None.
+*
+******************************************************************************/
+u8 *XHdcp22Tx_GetTopologyReceiverIdList(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.ReceiverId[0]);
+}
+
+/*****************************************************************************/
+/**
+* This function is used to get various fields inside the topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param    Field indicates what field of the topology structure to get.
+*
+* @return   Value associated to field inside the topology structure.
+*
+* @note     None.
+******************************************************************************/
+u32 XHdcp22Tx_GetTopologyField(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_TopologyField Field)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(Field < XHDCP22_TX_TOPOLOGY_INVALID);
+
+	switch(Field)
+	{
+	case XHDCP22_TX_TOPOLOGY_DEPTH :
+		return XHdcp22Tx_GetTopologyDepth(InstancePtr);
+	case XHDCP22_TX_TOPOLOGY_DEVICECNT :
+		return XHdcp22Tx_GetTopologyDeviceCnt(InstancePtr);
+	case XHDCP22_TX_TOPOLOGY_MAXDEVSEXCEEDED :
+		return XHdcp22Tx_GetTopologyMaxDevsExceeded(InstancePtr);
+	case XHDCP22_TX_TOPOLOGY_MAXCASCADEEXCEEDED :
+		return XHdcp22Tx_GetTopologyMaxCascadeExceeded(InstancePtr);
+	case XHDCP22_TX_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM:
+		return XHdcp22Tx_GetTopologyHdcp2LegacyDeviceDownstream(InstancePtr);
+	case XHDCP22_TX_TOPOLOGY_HDCP1DEVICEDOWNSTREAM :
+		return XHdcp22Tx_GetTopologyHdcp1DeviceDownstream(InstancePtr);
+	default:
+		return 0;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the Content Stream Type.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx instance.
+* @param  StreamType specifies the content stream type.
+*
+* @return None
+*
+******************************************************************************/
+void XHdcp22Tx_SetContentStreamType(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_ContentStreamType StreamType)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Info.ContentStreamType = StreamType;
+	InstancePtr->Info.IsContentStreamTypeSet = (TRUE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads the version.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   Returns the version register of the cipher.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdcp22Tx_GetVersion(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	return XHdcp22Cipher_GetVersion(&InstancePtr->Cipher);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function computes the subcore absolute address on axi-lite interface
+* Subsystem is mapped at an absolute address and all included sub-cores are
+* at pre-defined offset from the subsystem base address. To access the subcore
+* register map from host CPU an absolute address is required.
+*
+* @param  BaseAddress is the base address of the subsystem instance
+* @param  SubcoreOffset is the offset of the the subcore instance
+* @param  SubcoreAddressPtr is the computed base address of the subcore instance
+*
+* @return XST_SUCCESS if base address computation is successful and within
+*         subsystem address range else XST_FAILURE
+*
+******************************************************************************/
+static int XHdcp22Tx_ComputeBaseAddress(UINTPTR BaseAddress, UINTPTR SubcoreOffset, UINTPTR *SubcoreAddressPtr)
+{
+	int Status;
+	UINTPTR Address;
+
+	Address = BaseAddress | SubcoreOffset;
+	if((Address >= BaseAddress))
+	{
+		*SubcoreAddressPtr = Address;
+		Status = XST_SUCCESS;
+	}
+	else
+	{
+		*SubcoreAddressPtr = 0;
+		Status = XST_FAILURE;
+	}
+
+	return (Status);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a called to start authentication.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*    - XST_SUCCESS if authenticated is started successfully.
+*    - XST_FAIL if the state machine is disabled.
+*
+* @note  None.
+*
+******************************************************************************/
+int XHdcp22Tx_Authenticate(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr);
+
+	/* return a failure if not enabled */
+	if (InstancePtr->Info.IsEnabled == (FALSE))
+		return XST_FAILURE;
+
+	/* state H1 checks this one */
+	InstancePtr->Info.IsReceiverHDCP2Capable = (FALSE);
+
+	/* initialize statemachine, and set to busy status */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_AUTHENTICATION_BUSY;
+	InstancePtr->Info.CurrentState = XHDCP22_TX_STATE_H0;
+	InstancePtr->Info.PrvState = XHDCP22_TX_STATE_H0;
+
+	/* Clear Topology Available flag */
+	InstancePtr->Info.IsTopologyAvailable = (FALSE);
+
+	/* If in repeater mode, clear the content stream type is set flag */
+	if (XHdcp22Tx_IsRepeater(InstancePtr)) {
+		InstancePtr->Info.IsContentStreamTypeSet = (FALSE);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a executed every time to trigger the state machine.
+* The user of HDCP22 TX is responsible to call this function on a regular base.
+*
+* @param   InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return  Enumerated authentication status defined in
+*          #XHdcp22_Tx_AuthenticationType.
+*
+* @note    None.
+*
+******************************************************************************/
+int XHdcp22Tx_Poll(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22_Tx_StateType NewState;
+	XHdcp22_Tx_TransitionFuncType *Transition;
+	XHdcp22_Tx_AuthenticationType PrvAuthenticationStatus;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* return immediately if not enabled */
+	if (InstancePtr->Info.IsEnabled == (FALSE))
+		return (int)(InstancePtr->Info.AuthenticationStatus);
+
+	/* Store the authentication status before executing the next state */
+	PrvAuthenticationStatus = InstancePtr->Info.AuthenticationStatus;
+
+	/* Set timer expired signaling flag */
+	if (InstancePtr->Timer.TimerExpired == (TRUE) && InstancePtr->Info.IsEnabled) {
+		XHdcp22Tx_ReadRxStatus(InstancePtr);
+	}
+
+	/* continue executing the statemachine */
+	NewState = XHdcp22_Tx_StateTable[InstancePtr->Info.CurrentState](InstancePtr);
+	Transition = transition_table[InstancePtr->Info.CurrentState][NewState];
+
+	if (Transition != NULL)
+		Transition(InstancePtr);
+
+	InstancePtr->Info.PrvState = InstancePtr->Info.CurrentState;
+	InstancePtr->Info.CurrentState = NewState;
+
+	/* Log only if the AuthenticationStatus status changes and do not log
+	 * XHDCP22_TX_AUTHENTICATION_BUSY to avoid polluting the log buffer
+	 */
+	if(PrvAuthenticationStatus != InstancePtr->Info.AuthenticationStatus &&
+	   InstancePtr->Info.AuthenticationStatus != XHDCP22_TX_AUTHENTICATION_BUSY) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_POLL_RESULT,
+		                (u8)InstancePtr->Info.AuthenticationStatus);
+	}
+
+	return (int)(InstancePtr->Info.AuthenticationStatus);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function resets the state machine.
+*
+* @param   InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return  XST_SUCCESS
+*
+* @note    None.
+*
+******************************************************************************/
+int XHdcp22Tx_Reset(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* If in a authenticated state, execute the unauthenticated callback */
+	if (InstancePtr->Info.AuthenticationStatus == XHDCP22_TX_AUTHENTICATED) {
+		if (InstancePtr->IsUnauthenticatedCallbackSet)
+			InstancePtr->UnauthenticatedCallback(InstancePtr->UnauthenticatedCallbackRef);
+	}
+
+	/* Initialize statemachine, but do not run it */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_UNAUTHENTICATED;
+	InstancePtr->Info.CurrentState = XHDCP22_TX_STATE_H0;
+	InstancePtr->Info.PrvState = XHDCP22_TX_STATE_H0;
+
+	/* Clear statistics counters */
+	InstancePtr->Info.AuthRequestCnt = 0;
+	InstancePtr->Info.ReauthRequestCnt = 0;
+
+	/* Stop the timer if it's still running */
+	XTmrCtr_Stop(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0);
+
+	/* Clear Topology Available flag */
+	InstancePtr->Info.IsTopologyAvailable = (FALSE);
+
+	/* Disable encryption */
+	XHdcp22Tx_DisableEncryption(InstancePtr);
+
+     /* Reset Cipher */
+	XHdcp22Cipher_Disable(&InstancePtr->Cipher);
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_RESET, 0);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the state machine and acts as a resume.
+*
+* @param   InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return  XST_SUCCESS
+*
+* @note    None.
+*
+******************************************************************************/
+int XHdcp22Tx_Enable(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	InstancePtr->Info.IsEnabled = (TRUE);
+	XHdcp22Cipher_Enable(&InstancePtr->Cipher);
+	XTmrCtr_Stop(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_ENABLED, 1);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the state machine and acts as a pause.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return XST_SUCCESS.
+*
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_Disable(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	InstancePtr->Info.IsEnabled = (FALSE);
+	XHdcp22Cipher_Disable(&InstancePtr->Cipher);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_ENABLED, 0);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables HDMI stream encryption by enabling the cipher.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return - XST_SUCCESS if authenticated is started successfully.
+*         - XST_FAIL if the state machine is disabled.
+*
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_EnableEncryption(XHdcp22_Tx *InstancePtr)
+{
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	if (XHdcp22Tx_IsAuthenticated(InstancePtr)) {
+		XHdcp22Cipher_EnableTxEncryption(&InstancePtr->Cipher);
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_ENCR_ENABLED, 1);
+		return XST_SUCCESS;
+  }
+
+  return XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables HDMI stream encryption by disabling the cipher.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return XST_SUCCESS.
+*
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_DisableEncryption(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	XHdcp22Cipher_DisableTxEncryption(&InstancePtr->Cipher);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_ENCR_ENABLED, 0);
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the blank output for the cipher.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return - XST_SUCCESS if authenticated is started successfully.
+*         - XST_FAIL if the state machine is disabled.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_EnableBlank(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	XHdcp22Cipher_Blank(&InstancePtr->Cipher, TRUE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the blank output for the cipher.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return - XST_SUCCESS if authenticated is started successfully.
+*         - XST_FAIL if the state machine is disabled.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_DisableBlank(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	XHdcp22Cipher_Blank(&InstancePtr->Cipher, FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current repeater mode status.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx instance.
+*
+* @return
+*   - TRUE if the HDCP 2.2 instance is part of the downstream port of a repeater
+*   - FALSE if the HDCP 2.2 instance is a transmitter
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsRepeater(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Config.Mode != XHDCP22_TX_TRANSMITTER)?TRUE:FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the repeater mode status.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx instance.
+* @param  Set is TRUE to enable the repeater mode and FALSE to disable.
+*
+* @return None.
+*
+******************************************************************************/
+void XHdcp22Tx_SetRepeater(XHdcp22_Tx *InstancePtr, u8 Set)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	if (Set)
+		InstancePtr->Config.Mode = XHDCP22_TX_REPEATER;
+	else
+		InstancePtr->Config.Mode = XHDCP22_TX_TRANSMITTER;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current enabled state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return TRUE if enabled otherwise FALSE.
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsEnabled (XHdcp22_Tx *InstancePtr)
+{
+	return InstancePtr->Info.IsEnabled;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current encryption enabled state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return TRUE if encryption is enabled otherwise FALSE.
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsEncryptionEnabled (XHdcp22_Tx *InstancePtr)
+{
+	u32 Status;
+
+	Status = XHdcp22Cipher_IsEncrypted(&InstancePtr->Cipher);
+
+	return (Status) ? TRUE : FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current progress state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return TRUE if authentication is in progress otherwise FALSE.
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsInProgress (XHdcp22_Tx *InstancePtr)
+{
+	return (InstancePtr->Info.AuthenticationStatus !=
+	       XHDCP22_TX_UNAUTHENTICATED) ? (TRUE) : (FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current authenticated state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return TRUE if authenticated otherwise FALSE.
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsAuthenticated (XHdcp22_Tx *InstancePtr)
+{
+	return (InstancePtr->Info.AuthenticationStatus ==
+	                    XHDCP22_TX_AUTHENTICATED) ? (TRUE) : (FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function checks if the downstream device HDCP2Version register is set.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return - TRUE if downstream device is HDCP 2.2 capable.
+*         - FALSE if downstream device is not HDCP 2.2 capable.
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XHdcp22Tx_IsDwnstrmCapable (XHdcp22_Tx *InstancePtr)
+{
+	u8 DdcBuf[1];
+	int Status = XST_FAILURE;
+
+	if (InstancePtr->DdcHandlerRef) {
+		/* Read HDCP2Version register */
+		InstancePtr->IsReceiverHDCP2Capable = (FALSE);
+		DdcBuf[0] = XHDCP22_TX_HDCPPORT_VERSION_OFFSET;
+		Status = InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS, 1, DdcBuf,
+		                              (FALSE), InstancePtr->DdcHandlerRef);
+		if (Status == (XST_SUCCESS)) {
+			Status = InstancePtr->DdcRead(XHDCP22_TX_DDC_BASE_ADDRESS,
+			                              sizeof(DdcBuf), DdcBuf, (TRUE),
+			                              InstancePtr->DdcHandlerRef);
+		}
+	}
+
+	/* Check expected value */
+	if (Status == (XST_SUCCESS)) {
+		if (DdcBuf[0]  == 0x04) {
+			return TRUE;
+		}
+		else {
+			return FALSE;
+          }
+	}
+	else {
+		return FALSE;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs callback functions for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                                        Callback Function Type
+* -------------------------                          ---------------------------
+* (XHDCP22_TX_HANDLER_DDC_WRITE)                     DdcWrite
+* (XHDCP22_TX_HANDLER_DDC_READ)                      DdcRead
+* (XHDCP22_TX_HANDLER_AUTHENTICATED)                 AuthenticatedCallback
+* (XHDCP22_TX_HANDLER_UNAUTHENTICATED)               UnauthenticatedCallback
+* (XHDCP22_TX_HANDLER_DOWNSTREAM_TOPOLOGY_AVAILABLE) DownstreamTopologyAvailableCallback
+* </pre>
+*
+* @param	InstancePtr is a pointer to the HDMI RX core instance.
+* @param	HandlerType specifies the type of handler.
+* @param	CallbackFunc is the address of the callback function.
+* @param	CallbackRef is a user data item that will be passed to the
+*			callback function when it is invoked.
+*
+* @return
+*			- XST_SUCCESS if callback function installed successfully.
+*			- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*			installed replaces it with the new handler.
+*
+******************************************************************************/
+int XHdcp22Tx_SetCallback(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_HandlerType HandlerType, void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(HandlerType > (XHDCP22_TX_HANDLER_UNDEFINED));
+	Xil_AssertNonvoid(HandlerType < (XHDCP22_TX_HANDLER_INVALID));
+	Xil_AssertNonvoid(CallbackFunc != NULL);
+	Xil_AssertNonvoid(CallbackRef != NULL);
+
+	u32 Status;
+
+	/* Check for handler type */
+	switch (HandlerType)
+	{
+		// DDC write
+		case (XHDCP22_TX_HANDLER_DDC_WRITE):
+			InstancePtr->DdcWrite = (XHdcp22_Tx_DdcHandler)CallbackFunc;
+			InstancePtr->DdcHandlerRef = CallbackRef;
+			InstancePtr->IsDdcWriteSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// DDC read
+		case (XHDCP22_TX_HANDLER_DDC_READ):
+			InstancePtr->DdcRead = (XHdcp22_Tx_DdcHandler)CallbackFunc;
+			InstancePtr->DdcHandlerRef = CallbackRef;
+			InstancePtr->IsDdcReadSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Authenticated
+		case (XHDCP22_TX_HANDLER_AUTHENTICATED):
+			InstancePtr->AuthenticatedCallback = (XHdcp22_Tx_Callback)CallbackFunc;
+			InstancePtr->AuthenticatedCallbackRef = CallbackRef;
+			InstancePtr->IsAuthenticatedCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Authentication failed
+		case (XHDCP22_TX_HANDLER_UNAUTHENTICATED):
+			InstancePtr->UnauthenticatedCallback = (XHdcp22_Tx_Callback)CallbackFunc;
+			InstancePtr->UnauthenticatedCallbackRef = CallbackRef;
+			InstancePtr->IsUnauthenticatedCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		// Downstream topology is available
+		case (XHDCP22_TX_HANDLER_DOWNSTREAM_TOPOLOGY_AVAILABLE) :
+			InstancePtr->DownstreamTopologyAvailableCallback = (XHdcp22_Tx_Callback)CallbackFunc;
+			InstancePtr->DownstreamTopologyAvailableCallbackRef = CallbackRef;
+			InstancePtr->IsDownstreamTopologyAvailableCallbackSet = (TRUE);
+			Status = (XST_SUCCESS);
+			break;
+
+		default:
+			Status = (XST_INVALID_PARAM);
+			break;
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to the internal timer control instance
+* needed for connecting the timer interrupt to an interrupt controller.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return A pointer to the internal timer control instance.
+*
+* @note   None.
+*
+******************************************************************************/
+XTmrCtr* XHdcp22Tx_GetTimer(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	return &InstancePtr->Timer.TmrCtr;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the implementation of the HDCP transmit H0 state.
+* According protocol this is the reset state that is entered initially.
+* As soon as hot plug is detected and Rx is available, a transisition to state h1 is
+* performed. Since hotplug detect is controlled by the user,
+* the next state is always state H1.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return XHDCP22_TX_STATE_H1
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateH0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_H0);
+
+	return XHDCP22_TX_STATE_H1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the implementation of the HDCP transmit H1 state.
+* As soon as hot plug is detected and Rx is available, a transisition to
+* this state is performed. Hotplug detection if controlled by the user of this core.
+* This means that this state is practically the entry state.
+*
+* @param  InstancePtr is a pointer to the XHDCP22 TX core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_A0 if the attached receiver is HDCP2 capable.
+*         - XHDCP22_TX_STATE_H1 if the attached receiver is NOT HDCP2 capable.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateH1(XHdcp22_Tx *InstancePtr)
+{
+	/* Avoid polluting */
+	if (InstancePtr->Info.PrvState != InstancePtr->Info.CurrentState) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_H1);
+	}
+
+	/* Stay in this state until XHdcp22Tx_Authenticate is called and the status
+	 * is set to XHDCP22_TX_AUTHENTICATION_BUSY */
+	if (InstancePtr->Info.AuthenticationStatus != XHDCP22_TX_AUTHENTICATION_BUSY) {
+		return XHDCP22_TX_STATE_H1;
+	}
+
+	/* HDCP2Version */
+	InstancePtr->IsReceiverHDCP2Capable = XHdcp22Tx_IsDwnstrmCapable(InstancePtr);
+
+	if (InstancePtr->IsReceiverHDCP2Capable) {
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_INCOMPATIBLE_RX;
+	return XHDCP22_TX_STATE_H1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the implementation of the HDCP transmit A0 state.
+* If content protection not desired, return to H1 state.
+*
+* @param  InstancePtr is a pointer to the XHDCP22 TX core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_H1 if state machine is set to disabled (content protection
+*           NOT desired).
+*         - XHDCP22_TX_STATE_A1 if authentication must start.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_A0);
+
+	/* Check if HDCP2Capable flag is true */
+	if (!InstancePtr->IsReceiverHDCP2Capable) {
+		InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_INCOMPATIBLE_RX;
+		return XHDCP22_TX_STATE_H1;
+	}
+
+	/* Content protection not desired; go back to H1 state */
+	if (InstancePtr->Info.IsEnabled == (FALSE))
+		return XHDCP22_TX_STATE_H1;
+
+	/* Authentication starts, set status as BUSY */
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_AUTHENTICATION_BUSY;
+
+	/* Disable encryption */
+	XHdcp22Tx_DisableEncryption(InstancePtr);
+
+	/* Start the timer for authentication.
+        This is required to ensure that encryption is disabled before
+        authentication is requested */
+	XHdcp22Tx_StartTimer(InstancePtr, 100, XHDCP22_TX_AKE_INIT);
+
+	return XHDCP22_TX_STATE_A1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the first part of the A1 state of the
+* HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return XHDCP22_TX_STATE_A1_1
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA1(XHdcp22_Tx *InstancePtr)
+{
+	int Result = XST_SUCCESS;
+
+#ifndef _XHDCP22_TX_DISABLE_TIMEOUT_CHECKING_
+     /* Wait for 100ms timer to expire
+        This timeout ensures that encryption is disabled
+        before authentication is requested */
+	if (InstancePtr->Timer.TimerExpired == (FALSE)) {
+		return XHDCP22_TX_STATE_A1;
+	}
+#endif
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_A1);
+
+	/* Write AKE_Init message */
+	Result = XHdcp22Tx_WriteAKEInit(InstancePtr);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Start the timer for receiving XHDCP22_TX_AKE_SEND_CERT */
+	XHdcp22Tx_StartTimer(InstancePtr, 100, XHDCP22_TX_AKE_SEND_CERT);
+
+	/* Reset some variables */
+	InstancePtr->Topology.DeviceCnt = 0;
+	InstancePtr->Topology.Depth = 0;
+	InstancePtr->Topology.MaxDevsExceeded = FALSE;
+	InstancePtr->Topology.MaxCascadeExceeded = FALSE;
+	InstancePtr->Topology.Hdcp2LegacyDeviceDownstream = FALSE;
+	InstancePtr->Topology.Hdcp1DeviceDownstream = FALSE;
+	InstancePtr->Info.ReceivedFirstSeqNum_V = FALSE;
+	InstancePtr->Info.SentFirstSeqNum_M = FALSE;
+	InstancePtr->Info.IsContentStreamTypeSent = FALSE;
+	InstancePtr->Info.SeqNum_M = 0;
+	InstancePtr->Info.ContentStreamManageCheckCounter = 0;
+
+	/* Goto the waiting state for AKE_SEND_CERT */
+	return XHDCP22_TX_STATE_A1_1;
+}
+
+/******************************************************************************/
+/**
+*
+* This function executes a part of the A1 state functionality of the HDCP2.2
+* TX protocol.
+* It receives the certificate and decides if it should continue to a
+* 'no stored km' or 'stored Km'intermediate state.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_A0 on errors.
+*         - XHDCP22_TX_STATE_A1_1 if busy waiting for the
+*           XHDCP22_TX_AKE_SEND_CERT message.
+*         - XHDCP22_TX_STATE_A1_SK0 for a 'Stored Km' scenario.
+*         - XHDCP22_TX_STATE_A1_NSK0 for a 'Non Stored Km' scenario.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_1(XHdcp22_Tx *InstancePtr)
+{
+	int Result = XST_SUCCESS;
+	XHdcp22_Tx_DDCMessage *MsgPtr = (XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr = NULL;
+	const u8* KPubDpcPtr = NULL;
+	XHdcp22_Tx_PairingInfo NewPairingInfo;
+
+	/* receive AKE Send message, wait for 100 ms */
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, sizeof(XHdcp22_Tx_AKESendCert), FALSE);
+	if (Result != XST_SUCCESS) {
+		return XHDCP22_TX_STATE_A0;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A1_1;
+	}
+
+	/* Log after waiting */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_A1_1);
+
+	/* Receive the RX certificate */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_CERT);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_AKE_SEND_CERT,
+									sizeof(XHdcp22_Tx_AKESendCert));
+	if (Result != XST_SUCCESS) {
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Verify the signature */
+	KPubDpcPtr = XHdcp22Tx_GetKPubDpc(InstancePtr);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_VERIFY_SIGNATURE);
+	Result = XHdcp22Tx_VerifyCertificate(&MsgPtr->Message.AKESendCert.CertRx,
+	                   KPubDpcPtr, /* N */
+	                   XHDCP22_TX_KPUB_DCP_LLC_N_SIZE,
+	                   &KPubDpcPtr[XHDCP22_TX_KPUB_DCP_LLC_N_SIZE], /* e */
+	                   XHDCP22_TX_KPUB_DCP_LLC_E_SIZE);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_VERIFY_SIGNATURE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+	else {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_VERIFY_SIGNATURE_PASS);
+	}
+
+	/* SRM and revocation check are only performed by the top-level HDCP transmitter */
+	if (InstancePtr->Config.Mode == XHDCP22_TX_TRANSMITTER) {
+		/* Check to see wether there is a valid SRM loaded */
+		if (InstancePtr->Info.IsRevocationListValid == FALSE) {
+			/* No valid revocation list loaded. According to
+			 * the HDCP spec, authentication has to be aborted */
+			InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_NO_SRM_LOADED;
+			return XHDCP22_TX_STATE_A0;
+		}
+
+		/* Check to see wether the Receiver ID is in the revocation list */
+		if (XHdcp22Tx_IsDeviceRevoked(InstancePtr, MsgPtr->Message.AKESendCert.CertRx.ReceiverId)) {
+			XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+				XHDCP22_TX_LOG_DBG_DEVICE_IS_REVOKED);
+			InstancePtr->Info.IsDeviceRevoked = TRUE;
+			InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_DEVICE_IS_REVOKED;
+			return XHDCP22_TX_STATE_A0;
+		}
+		else {
+			InstancePtr->Info.IsDeviceRevoked = FALSE;
+		}
+	}
+
+	/* Add receiver ID to the topology info */
+	memcpy(&InstancePtr->Topology.ReceiverId[0],
+		MsgPtr->Message.AKESendCert.CertRx.ReceiverId,
+		XHDCP22_TX_RCVID_SIZE);
+	InstancePtr->Topology.DeviceCnt = 1;
+
+	/* Check to see wether the Receiver is an HDCP Repeater */
+	if (MsgPtr->Message.AKESendCert.RxCaps[2] & 0x1) { /* big endian! */
+		InstancePtr->Info.IsReceiverRepeater = TRUE;
+	}
+	else {
+		InstancePtr->Info.IsReceiverRepeater = FALSE;
+	}
+
+	/* Store received Rrx for calculations in other states */
+	memcpy(InstancePtr->Info.Rrx,  MsgPtr->Message.AKESendCert.Rrx,
+			 sizeof(InstancePtr->Info.Rrx));
+
+	/* Get pairing info pointer for the connected receiver */
+	PairingInfoPtr = XHdcp22Tx_GetPairingInfo(InstancePtr, MsgPtr->Message.AKESendCert.CertRx.ReceiverId);
+
+	/********************* Handle Stored Km **********************************/
+	/* If already existing handle Stored Km sequence: Write AKE_Stored_Km
+	 * and wait for H Prime */
+	if (PairingInfoPtr != NULL) {
+		if (PairingInfoPtr->Ready == TRUE) {
+			/* Update RxCaps in pairing info */
+			memcpy(PairingInfoPtr->RxCaps, MsgPtr->Message.AKESendCert.RxCaps,
+				sizeof(PairingInfoPtr->RxCaps));
+
+			/* Write encrypted Km */
+			Result = XHdcp22Tx_WriteAKEStoredKm(InstancePtr, PairingInfoPtr);
+
+			if (Result != XST_SUCCESS) {
+				XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+					XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+				return XHDCP22_TX_STATE_A0;
+			}
+
+			InstancePtr->Info.StateContext = PairingInfoPtr;
+
+			/* Start the timer for receiving XHDCP22_TX_AKE_SEND_HPRIME */
+			XHdcp22Tx_StartTimer(InstancePtr, 200, XHDCP22_TX_AKE_SEND_H_PRIME);
+			return XHDCP22_TX_STATE_A1_SK0;
+		}
+	}
+
+	/********************* Handle No Stored Km *******************************/
+	/* Update pairing info */
+	memcpy(NewPairingInfo.Rrx, InstancePtr->Info.Rrx,
+	       sizeof(NewPairingInfo.Rrx));
+	memcpy(NewPairingInfo.Rtx, InstancePtr->Info.Rtx,
+	       sizeof(NewPairingInfo.Rtx));
+	memcpy(NewPairingInfo.RxCaps, MsgPtr->Message.AKESendCert.RxCaps,
+	       sizeof(NewPairingInfo.RxCaps));
+	memcpy(NewPairingInfo.ReceiverId, MsgPtr->Message.AKESendCert.CertRx.ReceiverId,
+	       sizeof(NewPairingInfo.ReceiverId));
+
+	/* Generate the hashed Km */
+	XHdcp22Tx_GenerateKm(InstancePtr, NewPairingInfo.Km);
+
+	/* Done with first step, update pairing info and goto the next
+	 * step in the No Stored Km sequence: waiting for H Prime*/
+	PairingInfoPtr = XHdcp22Tx_UpdatePairingInfo(InstancePtr, &NewPairingInfo, FALSE);
+	if (PairingInfoPtr == NULL) {
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	InstancePtr->Info.StateContext = (void *)PairingInfoPtr;
+
+	/* Write encrypted Km  */
+	Result = XHdcp22Tx_WriteAKENoStoredKm(InstancePtr, &NewPairingInfo,
+	                             &MsgPtr->Message.AKESendCert.CertRx);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Start the timer for receiving XHDCP22_TX_AKE_SEND_HPRIME */
+	XHdcp22Tx_StartTimer(InstancePtr, 1000, XHDCP22_TX_AKE_SEND_H_PRIME);
+
+	return XHDCP22_TX_STATE_A1_NSK0;
+}
+
+/******************************************************************************/
+/**
+*
+* This function executes a part of the A1 state functionality of the HDCP2.2
+* TX protocol.
+* It handles a part of the 'No Stored Km' scenario and receives and verifies H'
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_A0 on errors.
+*         - XHDCP22_TX_STATE_A1_NSK0 if busy waiting for
+*           the XHDCP22_TX_AKE_SEND_H_PRIME message.
+*         - XHDCP22_TX_STATE_A1_NSK1 for the next part of the 'Stored Km' scenario.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_Nsk0(XHdcp22_Tx *InstancePtr)
+{
+	int Result = XST_SUCCESS;
+	u8 HPrime[XHDCP22_TX_H_PRIME_SIZE];
+
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+	                       (XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+	XHdcp22_Tx_DDCMessage *MsgPtr = (XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+
+	/* Wait for the receiver to respond within 1 second.
+	 * If the receiver has timed out we go to state A0.
+	 * If the receiver is busy, we stay in this state (return from polling).
+	 * If the receiver has finished, but the message was not handled yet,
+	 * we handle the message.*/
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, sizeof(XHdcp22_Tx_AKESendHPrime), FALSE);
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_InvalidatePairingInfo(InstancePtr, PairingInfoPtr->ReceiverId);
+		return XHDCP22_TX_STATE_A0;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A1_NSK0;
+	}
+
+	/* Log after waiting */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_A1_NSK0);
+
+	/* Receive H' */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_H1);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_AKE_SEND_H_PRIME,
+	                              sizeof(XHdcp22_Tx_AKESendHPrime));
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_InvalidatePairingInfo(InstancePtr, PairingInfoPtr->ReceiverId);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Verify the received H' */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+                  XHDCP22_TX_LOG_DBG_COMPUTE_H);
+	XHdcp22Tx_ComputeHPrime(PairingInfoPtr->Rrx, PairingInfoPtr->RxCaps,
+	                        PairingInfoPtr->Rtx, XHdcp22_Tx_TxCaps,
+	                        PairingInfoPtr->Km, HPrime);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_COMPUTE_H_DONE);
+
+	if(memcmp(MsgPtr->Message.AKESendHPrime.HPrime, HPrime, sizeof(HPrime)) != 0) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+		                XHDCP22_TX_LOG_DBG_COMPARE_H_FAIL);
+		XHdcp22Tx_InvalidatePairingInfo(InstancePtr, PairingInfoPtr->ReceiverId);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Start the timer for receiving XHDCP22_TX_AKE_SEND_PAIRING_INFO */
+	XHdcp22Tx_StartTimer(InstancePtr, 200, XHDCP22_TX_AKE_SEND_PAIRING_INFO);
+	return XHDCP22_TX_STATE_A1_NSK1;
+}
+
+/******************************************************************************/
+/**
+*
+* This function executes a part of the A1 state functionality of the HDCP2.2
+* TX protocol.
+* It handles a part of the  'No Stored Km' scenario and receives and
+* stores pairing info.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_A0 on errors.
+*         - XHDCP22_TX_STATE_A1_NSK1 if busy waiting for
+*           the XHDCP22_TX_AKE_SEND_PAIRING_INFO message.
+*         - XHDCP22_TX_STATE_A2 if authentication is done.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_Nsk1(XHdcp22_Tx *InstancePtr)
+{
+	int Result = XST_SUCCESS;
+
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+	                       (XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+	XHdcp22_Tx_DDCMessage *MsgPtr =
+	                       (XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+
+	/* Wait for the receiver to send AKE_Send_Pairing_Info */
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, sizeof(XHdcp22_Tx_AKESendPairingInfo), FALSE);
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_InvalidatePairingInfo(InstancePtr, PairingInfoPtr->ReceiverId);
+		return XHDCP22_TX_STATE_A0;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A1_NSK1;
+	}
+
+	/* Log after waiting */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+	                (u16)XHDCP22_TX_STATE_A1_NSK1);
+
+	/* Receive the expected message */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_EKHKM);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_AKE_SEND_PAIRING_INFO,
+	                              sizeof(XHdcp22_Tx_AKESendPairingInfo));
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_InvalidatePairingInfo(InstancePtr, PairingInfoPtr->ReceiverId);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Store the pairing info with the received Ekh(Km) */
+	memcpy(PairingInfoPtr->Ekh_Km, MsgPtr->Message.AKESendPairingInfo.EKhKm,
+	       sizeof(PairingInfoPtr->Ekh_Km));
+
+	XHdcp22Tx_UpdatePairingInfo(InstancePtr, PairingInfoPtr, TRUE);
+
+	/* Authentication done, goto the next state (exchange Ks) */
+	return XHDCP22_TX_STATE_A2;
+}
+
+/******************************************************************************/
+/**
+*
+* This function executes a part of the A1 state functionality of the HDCP2.2
+* TX protocol.
+* It handles a part of the  'Stored Km' scenario and receives and verifies
+* H'.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_A0 on errors.
+*         - XHDCP22_TX_STATE_A1_SK0 if busy waiting for the
+*         - XHDCP22_TX_AKE_SEND_H_PRIME message.
+*         - XHDCP22_TX_STATE_A2 if authentication is done.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType Xhdcp22Tx_StateA1_Sk0(XHdcp22_Tx *InstancePtr)
+{
+	int Result = XST_SUCCESS;
+	u8 HPrime[XHDCP22_TX_H_PRIME_SIZE];
+
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+						(XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+	XHdcp22_Tx_DDCMessage *MsgPtr = (XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+
+	/* Wait for the receiver to respond within 1 second.
+	 * If the receiver has timed out we go to state A0.
+	 * If the receiver is busy, we stay in this state (return from polling).
+	 * If the receiver has finished, but the message was not handled yet,
+	 * we handle the message.*/
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, sizeof(XHdcp22_Tx_AKESendHPrime), FALSE);
+	if (Result != XST_SUCCESS) {
+		return XHDCP22_TX_STATE_A0;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A1_SK0;
+	}
+
+	/* Log after waiting */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+	(u16)XHDCP22_TX_STATE_A1_SK0);
+
+	/* Receive the expected message */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_H1);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_AKE_SEND_H_PRIME,
+									sizeof(XHdcp22_Tx_AKESendHPrime));
+	if (Result != XST_SUCCESS) {
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Verify the received H' */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+								 XHDCP22_TX_LOG_DBG_COMPUTE_H);
+	XHdcp22Tx_ComputeHPrime(InstancePtr->Info.Rrx, PairingInfoPtr->RxCaps,
+							InstancePtr->Info.Rtx, XHdcp22_Tx_TxCaps,
+							PairingInfoPtr->Km, HPrime);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+								 XHDCP22_TX_LOG_DBG_COMPUTE_H_DONE);
+
+	if(memcmp(MsgPtr->Message.AKESendHPrime.HPrime, HPrime, sizeof(HPrime)) != 0) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+		                XHDCP22_TX_LOG_DBG_COMPARE_H_FAIL);
+		XHdcp22Tx_InvalidatePairingInfo(InstancePtr, PairingInfoPtr->ReceiverId);
+		return XHDCP22_TX_STATE_A0;
+	}
+	return XHDCP22_TX_STATE_A2;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A2 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA2(XHdcp22_Tx *InstancePtr)
+{
+	int Result;
+
+	/* Log but don't clutter our log buffer, check on counter */
+	if (InstancePtr->Info.LocalityCheckCounter == 0) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+		                (u16)XHDCP22_TX_STATE_A2);
+	}
+
+	/* It is allowed to retry locality check until it has been
+	 * checked for 1024 times */
+	InstancePtr->Info.LocalityCheckCounter++;
+
+	if (InstancePtr->Info.LocalityCheckCounter > XHDCP22_TX_MAX_ALLOWED_LOCALITY_CHECKS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_LCCHK_COUNT,
+		                (u16)InstancePtr->Info.LocalityCheckCounter-1);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Generate Rn */
+	XHdcp22Tx_GenerateRn(InstancePtr, InstancePtr->Info.Rn);
+
+	/* Send LC Init message */
+	Result = XHdcp22Tx_WriteLcInit(InstancePtr, InstancePtr->Info.Rn);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Start the timer for receiving XHDCP22_TX_AKE_SEND_PAIRING_INFO */
+	XHdcp22Tx_StartTimer(InstancePtr, 20, XHDCP22_TX_LC_SEND_L_PRIME);
+
+	return XHDCP22_TX_STATE_A2_1;
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function executes a part of the A2 state functionality of the HDCP2.2
+* TX protocol.
+* It receives and verifies L' (locality check).
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XHDCP22_TX_STATE_A2_1 if busy waiting for the
+*           XHDCP22_TX_AKE_SEND_L_PRIME message.
+*         - XHDCP22_TX_STATE_A3 if authentication is done.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA2_1(XHdcp22_Tx *InstancePtr)
+{
+	int Result = XST_SUCCESS;
+	u8 LPrime[XHDCP22_TX_H_PRIME_SIZE];
+
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+	                       (XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+	XHdcp22_Tx_DDCMessage *MsgPtr =
+	                      (XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+
+	/* Wait for the receiver to respond within 20 msecs.
+	 * If the receiver has timed out we go to state A2 for a retry.
+	 * If the receiver is busy, we stay in this state (return from polling).
+	 * If the receiver has finished, but the message was not handled yet,
+	 * we handle the message.*/
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, sizeof(XHdcp22_Tx_LCSendLPrime), FALSE);
+	if (Result != XST_SUCCESS) {
+		/* Retry state state A2 */
+		return XHDCP22_TX_STATE_A2;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A2_1;
+	}
+
+	/* Log after waiting (don't clutter our log buffer, check on counter) */
+	if (InstancePtr->Info.LocalityCheckCounter == 1) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+		                (u16)XHDCP22_TX_STATE_A2_1);
+	}
+
+	/* Receive the expected message */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_L1);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_LC_SEND_L_PRIME,
+	                              sizeof(XHdcp22_Tx_LCSendLPrime));
+	if (Result != XST_SUCCESS) {
+		/* Retry state state A2 */
+		return XHDCP22_TX_STATE_A2;
+	}
+
+	/* Verify the received L' */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	XHDCP22_TX_LOG_DBG_COMPUTE_L);
+	XHdcp22Tx_ComputeLPrime(InstancePtr->Info.Rn, PairingInfoPtr->Km,
+	                        InstancePtr->Info.Rrx, InstancePtr->Info.Rtx,
+	                        LPrime);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+		XHDCP22_TX_LOG_DBG_COMPUTE_L_DONE);
+
+	if(memcmp(MsgPtr->Message.LCSendLPrime.LPrime, LPrime, sizeof(LPrime)) != 0) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+			XHDCP22_TX_LOG_DBG_COMPARE_L_FAIL);
+		/* Retry state A2 */
+		return XHDCP22_TX_STATE_A2;
+	}
+
+	/* Log how many times the locality check was repeated (*/
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_LCCHK_COUNT,
+	                (u16)InstancePtr->Info.LocalityCheckCounter);
+	return XHDCP22_TX_STATE_A3;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A3 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA3(XHdcp22_Tx *InstancePtr)
+{
+	int Result;
+	u8 Riv[XHDCP22_TX_RIV_SIZE];
+	u8 Ks[XHDCP22_TX_KS_SIZE];
+	u8 EdkeyKs[XHDCP22_TX_EDKEY_KS_SIZE];
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+	                       (XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+	                (u16)XHDCP22_TX_STATE_A3);
+
+
+	XHdcp22Tx_GenerateRiv(InstancePtr, Riv);
+
+	/* Set Riv in the cipher */
+	XHdcp22Cipher_SetRiv(&InstancePtr->Cipher, Riv, XHDCP22_TX_RIV_SIZE);
+	XHdcp22Tx_GenerateKs(InstancePtr, Ks);
+
+	/* Set Ks in the cipher */
+	XHdcp22Cipher_SetKs(&InstancePtr->Cipher, Ks, XHDCP22_TX_KS_SIZE);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_COMPUTE_EDKEYKS);
+	XHdcp22Tx_ComputeEdkeyKs(InstancePtr->Info.Rn, PairingInfoPtr->Km, Ks,
+	                         InstancePtr->Info.Rrx, InstancePtr->Info.Rtx, EdkeyKs);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_COMPUTE_EDKEYKS_DONE);
+
+	/* Write encrypted sesssion key */
+	Result = XHdcp22Tx_WriteSkeSendEks(InstancePtr, EdkeyKs, Riv);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	return XHDCP22_TX_STATE_A4;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A4 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA4(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+	                (u16)XHDCP22_TX_STATE_A4);
+
+	if (InstancePtr->Info.IsReceiverRepeater) {
+
+		return XHDCP22_TX_STATE_A6_A7_A8;
+	}
+	else {
+		/* Start the mandatory 200 ms timer before authentication can be granted
+		 * and the cipher may be enabled */
+		XHdcp22Tx_StartTimer(InstancePtr, 200, XHDCP22_TX_TS_WAIT_FOR_CIPHER);
+
+		/* The downstream topology is definitive  */
+		InstancePtr->Info.IsTopologyAvailable = (TRUE);
+		if (InstancePtr->IsDownstreamTopologyAvailableCallbackSet)
+			InstancePtr->DownstreamTopologyAvailableCallback(InstancePtr->DownstreamTopologyAvailableCallbackRef);
+
+		return XHDCP22_TX_STATE_A5;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A5 state of the HDCP2.2 TX protocol.
+* Before authentication is granted, a 200 ms mandatory wait is added, so the
+* integrating application does not start the cipher premature.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA5(XHdcp22_Tx *InstancePtr)
+{
+
+#ifndef _XHDCP22_TX_DISABLE_TIMEOUT_CHECKING_
+	/* wait for a timer to expire, either it is the 200 ms mandatory time
+	 * before cipher enabling, or the re-authentication check timer */
+	if (InstancePtr->Timer.TimerExpired == (FALSE)) {
+		return XHDCP22_TX_STATE_A5;
+	}
+#endif
+
+	/* Do not pollute the logging on polling log authenticated only once */
+	if (InstancePtr->Info.AuthenticationStatus != XHDCP22_TX_AUTHENTICATED) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+		                (u16)XHDCP22_TX_STATE_A5);
+	}
+
+	/* Timer has expired, handle it */
+
+	/* Handle mandatory 200 ms cipher timeout */
+	if (InstancePtr->Timer.ReasonId == XHDCP22_TX_TS_WAIT_FOR_CIPHER) {
+		/* Check re-authentication before enabling cipher */
+		if ((InstancePtr->Info.RxStatus&XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK) ==
+		    XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK)
+		{
+			XHdcp22Tx_HandleReauthenticationRequest(InstancePtr);
+			return XHDCP22_TX_STATE_A0;
+		}
+		else
+		{
+			/* Authenticated ! */
+			InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_AUTHENTICATED;
+			InstancePtr->Info.ReAuthenticationRequested = (FALSE);
+
+			/* Authenticated callback */
+			if (InstancePtr->IsAuthenticatedCallbackSet) {
+				InstancePtr->AuthenticatedCallback(InstancePtr->AuthenticatedCallbackRef);
+			}
+
+			/* Start the re-authentication check timer */
+			XHdcp22Tx_StartTimer(InstancePtr, 1000, XHDCP22_TX_TS_RX_REAUTH_CHECK);
+			return XHDCP22_TX_STATE_A5;
+		}
+	}
+
+	/* Handle the re-authentication check timer */
+	if (InstancePtr->Timer.ReasonId == XHDCP22_TX_TS_RX_REAUTH_CHECK) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+		                XHDCP22_TX_LOG_DBG_CHECK_REAUTH);
+
+		if ((InstancePtr->Info.RxStatus&XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK) ==
+		    XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK)
+		{
+			XHdcp22Tx_HandleReauthenticationRequest(InstancePtr);
+			return XHDCP22_TX_STATE_A0;
+		}
+		/* Has the repeater built an updated downstream receiver ID list? */
+		if ((InstancePtr->Info.RxStatus&XHDCP22_TX_RXSTATUS_READY_MASK) ==
+			XHDCP22_TX_RXSTATUS_READY_MASK) {
+
+			/* The downstream topology has changed */
+			return XHDCP22_TX_STATE_A6_A7_A8;
+		}
+
+		/* Re-Start the timer for the next status check */
+		XHdcp22Tx_StartTimer(InstancePtr, 1000, XHDCP22_TX_TS_RX_REAUTH_CHECK);
+	}
+	return XHDCP22_TX_STATE_A5;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the states A6, A7 and A8 of the HDCP2.2 TX protocol.
+* Within these states the HDCP2.2 TX receives and verifies the receiver ID list.
+* The HDCP2.2 TX is required to send a respons within 2 seconds after the
+* HDCP2.2 repeater has made the receiver ID list available.
+* These states have been grouped in order to guarantee that the HDCP2.2 TX
+* responds as fast as it can.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA6_A7_A8(XHdcp22_Tx *InstancePtr)
+{
+	int Result;
+	u8 DeviceCount;
+	u8 V[XHDCP22_TX_V_SIZE];
+	u32 SeqNum_V;
+	int i;
+
+	/* When we (re)-enter this state the topology info is not available
+	 * so clear the topology available flag */
+	InstancePtr->Info.IsTopologyAvailable = (FALSE);
+
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+		(XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+	XHdcp22_Tx_DDCMessage *MsgPtr =
+		(XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+	/* Wait for the receiver to respond within 3 secs.
+	* If the receiver has timed out we go to state A0.
+	* If the receiver is busy, we stay in this state (return from polling).
+	* If the receiver has finished, but the message was not handled yet,
+	* we handle the message.*/
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, 0, TRUE);
+	if (Result != XST_SUCCESS) {
+		return XHDCP22_TX_STATE_A0;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A6_A7_A8;
+	}
+
+	/* Log after waiting */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE, (u16)XHDCP22_TX_STATE_A6_A7_A8);
+
+	/* Receive the expected message */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_RCVIDLIST);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_REPEATAUTH_SEND_RECVID_LIST,
+		InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK);
+	if (Result != XST_SUCCESS) {
+		/* Received message is invalid. Go to state A0 */
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Extract the RxInfo and set the topology info.
+	 * RxInfo is in big endian format */
+	DeviceCount = (MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[0] & 0x1) << 4;  // MSB
+	DeviceCount |= (MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[1] >> 4) & 0xF; // LSB
+
+	/* The device count extracted from RxInfo does not include
+	 * the HDCP repeater itself, hence the +1 */
+	InstancePtr->Topology.DeviceCnt = DeviceCount + 1;
+	InstancePtr->Topology.Depth =
+		(MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[0] >> 1) & 0x7;
+	InstancePtr->Topology.MaxDevsExceeded =
+		(MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[1] & 0x8) ? TRUE : FALSE;
+	InstancePtr->Topology.MaxCascadeExceeded =
+		(MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[1] & 0x4) ? TRUE : FALSE;
+	InstancePtr->Topology.Hdcp2LegacyDeviceDownstream =
+		(MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[1] & 0x2) ? TRUE : FALSE;
+	InstancePtr->Topology.Hdcp1DeviceDownstream =
+		(MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo[1] & 0x1) ? TRUE : FALSE;
+
+	/* State A7: Verify Receiver ID list */
+
+	/* Check the topology */
+	if (InstancePtr->Topology.MaxDevsExceeded == TRUE ||
+	    InstancePtr->Topology.MaxCascadeExceeded == TRUE) {
+		InstancePtr->Info.IsTopologyAvailable = (TRUE);
+		if (InstancePtr->IsDownstreamTopologyAvailableCallbackSet)
+			InstancePtr->DownstreamTopologyAvailableCallback(InstancePtr->DownstreamTopologyAvailableCallbackRef);
+		/* Topology error. Go to state A0 */
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Verify the received VPrime */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_COMPUTE_V);
+	XHdcp22Tx_ComputeV(InstancePtr->Info.Rn, InstancePtr->Info.Rrx,
+		MsgPtr->Message.RepeatAuthSendRecvIDList.RxInfo,
+		InstancePtr->Info.Rtx,
+		(u8 *)MsgPtr->Message.RepeatAuthSendRecvIDList.ReceiverIDs,
+		DeviceCount,
+		MsgPtr->Message.RepeatAuthSendRecvIDList.SeqNum_V,
+		PairingInfoPtr->Km,
+		V);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_COMPUTE_V_DONE);
+
+	/* Compare VPrime with the most significant 128-bits of V */
+	if (memcmp(MsgPtr->Message.RepeatAuthSendRecvIDList.VPrime, V, XHDCP22_TX_V_PRIME_SIZE) != 0) {
+		/* Missmatch V MSB and VPrime. Go to state A0 */
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_COMPARE_V_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	InstancePtr->Info.IsDeviceRevoked = FALSE;
+	for (i = 0; i < DeviceCount; i++) {
+		/* Add receiver ID to topology info. */
+		memcpy(&InstancePtr->Topology.ReceiverId[i + 1],
+			&MsgPtr->Message.RepeatAuthSendRecvIDList.ReceiverIDs[i],
+			XHDCP22_TX_RCVID_SIZE);
+
+		/* SRM and revocation check are only performed by the top-level HDCP transmitter */
+		if (InstancePtr->Config.Mode == XHDCP22_TX_TRANSMITTER) {
+			/* Check to see wether the receiver ID is revoked */
+			if (XHdcp22Tx_IsDeviceRevoked(InstancePtr,
+				MsgPtr->Message.RepeatAuthSendRecvIDList.ReceiverIDs[i])) {
+				InstancePtr->Info.IsDeviceRevoked = TRUE;
+				InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_DEVICE_IS_REVOKED;
+				/* Device is revoked. Go to state A0 */
+				return XHDCP22_TX_STATE_A0;
+			}
+		}
+	}
+
+	/* Get the seq_num_V. Value is in big endian format */
+	SeqNum_V  = MsgPtr->Message.RepeatAuthSendRecvIDList.SeqNum_V[0] << 16; // MSB
+	SeqNum_V |= MsgPtr->Message.RepeatAuthSendRecvIDList.SeqNum_V[1] << 8;
+	SeqNum_V |= MsgPtr->Message.RepeatAuthSendRecvIDList.SeqNum_V[2];       // LSB
+
+	/* Verify the seq_num_V value */
+	if (InstancePtr->Info.ReceivedFirstSeqNum_V == FALSE) {
+		if (SeqNum_V != 0) {
+			/* First value should be 0. Go to state A0 */
+			return XHDCP22_TX_STATE_A0;
+		}
+		InstancePtr->Info.ReceivedFirstSeqNum_V = TRUE;
+	}
+	else {
+		/* Check for roll-over of seq_num_V */
+		if (SeqNum_V == 0) {
+			/* Roll-over of seq_num_V. Go to state A0 */
+			return XHDCP22_TX_STATE_A0;
+		}
+	}
+
+	/* State A8: Send Receiver ID list acknowledgement */
+	Result = XHdcp22Tx_WriteRepeaterAuth_Send_Ack(InstancePtr, &V[XHDCP22_TX_V_PRIME_SIZE]);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* The downstream topology is definitive  */
+	InstancePtr->Info.IsTopologyAvailable = (TRUE);
+	if (InstancePtr->IsDownstreamTopologyAvailableCallbackSet)
+		InstancePtr->DownstreamTopologyAvailableCallback(InstancePtr->DownstreamTopologyAvailableCallbackRef);
+
+	/* Have we already sent the Content Stream Type? */
+	if (InstancePtr->Info.IsContentStreamTypeSent == TRUE) {
+		/* Start the re-authentication check timer */
+		XHdcp22Tx_StartTimer(InstancePtr, 1000, XHDCP22_TX_TS_RX_REAUTH_CHECK);
+
+		/* Go to state A5 */
+		return XHDCP22_TX_STATE_A5;
+	}
+	else {
+		/* Go to state A9 */
+		return XHDCP22_TX_STATE_A9;
+	}
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A6 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA6(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+		(u16)XHDCP22_TX_STATE_A6);
+	return XHDCP22_TX_STATE_A0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A7 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA7(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+	                (u16)XHDCP22_TX_STATE_A7);
+	return XHDCP22_TX_STATE_A0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the A8 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA8(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+	                (u16)XHDCP22_TX_STATE_A8);
+	return XHDCP22_TX_STATE_A0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the first portion of the A9 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA9(XHdcp22_Tx *InstancePtr)
+{
+	int Result;
+
+#ifndef _XHDCP22_TX_DISABLE_TIMEOUT_CHECKING_
+	/* Wait for the stream manage timer to expire */
+	if (InstancePtr->Timer.TimerExpired == (FALSE)) {
+		return XHDCP22_TX_STATE_A9;
+	}
+#endif
+
+	/* Timer has expired, handle it */
+
+	/* Check re-authentication */
+	XHdcp22Tx_ReadRxStatus(InstancePtr);
+	if ((InstancePtr->Info.RxStatus&XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK) ==
+		XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK) {
+		XHdcp22Tx_HandleReauthenticationRequest(InstancePtr);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Check if the Content Stream Type is available.
+	 * If not set, we stay in this state (return from polling) and set a timer */
+	if (InstancePtr->Info.IsContentStreamTypeSet == FALSE) {
+		/* Start the wait for stream type timer */
+		XHdcp22Tx_StartTimer(InstancePtr, 50, XHDCP22_TX_TS_WAIT_FOR_STREAM_TYPE);
+		return XHDCP22_TX_STATE_A9;
+	}
+
+	/* Log but don't clutter our log buffer, check on counter */
+	if (InstancePtr->Info.ContentStreamManageCheckCounter == 0) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+		                (u16)XHDCP22_TX_STATE_A9);
+	}
+
+	if (InstancePtr->Info.ContentStreamManageCheckCounter >= XHDCP22_TX_MAX_ALLOWED_STREAM_MANAGE_CHECKS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STRMMNGCHK_COUNT,
+		                (u16)InstancePtr->Info.ContentStreamManageCheckCounter);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Check for roll-over of seq_num_M */
+	if ((InstancePtr->Info.SentFirstSeqNum_M == TRUE) &&
+		(InstancePtr->Info.SeqNum_M == 0)) {
+		/* Roll-over detected. According to the state-diagram
+		 * we should go to state H1 and restart authentication.
+		 * Instead of doing that we restart authentication by going to state A0 */
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Send the Content Stream Manage message */
+	Result = XHdcp22Tx_WriteRepeaterAuth_Stream_Manage(InstancePtr);
+
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL);
+		return XHDCP22_TX_STATE_A0;
+	}
+
+	/* Start the timer for receiving XHDCP22_TX_REPEATAUTH_STREAM_READY */
+	XHdcp22Tx_StartTimer(InstancePtr, 100, XHDCP22_TX_REPEATAUTH_STREAM_READY);
+
+	InstancePtr->Info.SentFirstSeqNum_M = TRUE;
+	InstancePtr->Info.ContentStreamManageCheckCounter++;
+
+	return XHDCP22_TX_STATE_A9_1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes the second portion of the A9 state of the HDCP2.2 TX protocol.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return The next state to execute.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_StateType XHdcp22Tx_StateA9_1(XHdcp22_Tx *InstancePtr)
+{
+	int Result;
+
+	XHdcp22_Tx_DDCMessage *MsgPtr =
+		(XHdcp22_Tx_DDCMessage *)InstancePtr->MessageBuffer;
+
+	/* Wait for the receiver to respond within 100 msecs.
+	* If the receiver has timed out we go to state A9 for a retry.
+	* If the receiver is busy, we stay in this state (return from polling).
+	* If the receiver has finished, but the message was not handled yet,
+	* we handle the message.*/
+	Result = XHdcp22Tx_WaitForReceiver(InstancePtr, XHDCP22_TX_REPEATAUTH_STREAM_READY_SIZE, FALSE);
+	if (Result != XST_SUCCESS) {
+		/* Timeout. Go to state A9 for a retry */
+		InstancePtr->Info.ContentStreamManageFailed = TRUE;
+		return XHDCP22_TX_STATE_A9;
+	}
+	if (InstancePtr->Info.MsgAvailable == (FALSE)) {
+		return XHDCP22_TX_STATE_A9_1;
+	}
+
+	/* Log after waiting (don't clutter our log buffer, check on counter) */
+	if (InstancePtr->Info.ContentStreamManageCheckCounter == 1) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_STATE,
+		                (u16)XHDCP22_TX_STATE_A9_1);
+	}
+
+	/* Receive the expected message */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_RX_M1);
+	Result = XHdcp22Tx_ReceiveMsg(InstancePtr, XHDCP22_TX_REPEATAUTH_STREAM_READY,
+		                                            XHDCP22_TX_REPEATAUTH_STREAM_READY_SIZE);
+	if (Result != XST_SUCCESS) {
+		/* Received message is invalid. Go to state A9 for a retry */
+		InstancePtr->Info.ContentStreamManageFailed = TRUE;
+		return XHDCP22_TX_STATE_A9;
+	}
+
+	/* Verify the received MPrime */
+	/* We've allready calculated and stored the expected value in the
+	 * XHdcp22Tx_WriteRepeaterAuth_Stream_Manage function */
+	/* Compare MPrime with M */
+	if (memcmp(MsgPtr->Message.RepeatAuthStreamReady.MPrime, InstancePtr->Info.M,
+		XHDCP22_TX_M_PRIME_SIZE) != 0) {
+		/* Missmatch M and MPrime. Go to state A9 for a retry */
+		InstancePtr->Info.ContentStreamManageFailed = TRUE;
+		return XHDCP22_TX_STATE_A9;
+	}
+
+	/* According to the spec, the HDCP transmitter must write the
+	 * RepeaterAuth_Stream_Manage message at least 100ms before the
+	 * transmission of the corresponding Content Stream. Just to make
+	 * sure the wait time is met, wait for 100ms. */
+	XHdcp22Tx_StartTimer(InstancePtr, 100, XHDCP22_TX_TS_WAIT_FOR_CIPHER);
+
+	InstancePtr->Info.ContentStreamManageFailed = FALSE;
+	InstancePtr->Info.IsContentStreamTypeSent = TRUE;
+	return XHDCP22_TX_STATE_A5;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A1 or one of its sub states
+* to A0, which means that an error in authentication has occured.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A1A0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_HandleAuthenticationFailed(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A1_SK0 or A1_NSK1 to A2,
+* which means that state A2 is executed for the first time.
+* The locality check counter is initialized.
+* Subsequent locality checks are then executed for an extra 1023 times.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A1A2(XHdcp22_Tx *InstancePtr)
+{
+	InstancePtr->Info.LocalityCheckCounter = 0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A2 or one of its substates
+* to A0, which means that an error in authentication has occured.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A2A0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_HandleAuthenticationFailed(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A3 to A0, which means that
+* an error in authetication has occured.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A3A0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_HandleAuthenticationFailed(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A3 to A4, which means that
+* the Session Key Exchange (SKE) has completed.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A3A4(XHdcp22_Tx *InstancePtr)
+{
+	/* Check to see wether the Receiver is an HDCP Repeater */
+	if (InstancePtr->Info.IsReceiverRepeater) {
+		/* Start timer for receiving the Receiver ID list */
+		XHdcp22Tx_StartTimer(InstancePtr, 3000, XHDCP22_TX_REPEATAUTH_SEND_RECVID_LIST);
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A4 to A5, which means that
+* an authetication has succeeded and state A5 is executed the first time.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A4A5(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A6 or A7 to A0, which means that
+* an error in authetication has occured.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A6A7A0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_HandleAuthenticationFailed(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function executes on transition from state A9 to A0, which means that
+* an error in the content stream management has occured.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_A9A0(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22Tx_HandleAuthenticationFailed(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a dummy called as long as there is no valid ddc handler set.
+* It always returns an error.
+*
+* @param  DeviceAddress is the DDC (i2c) device address.
+* @param  ByteCount is the number of bytes in the buffer.
+* @param  BufferPtr is the buffer that stores the data to be written or read.
+* @param  Stop is a flag to signal i2c stop condition.
+* @param  RefPtr is the reference pointer for the handler.
+*
+* @return XST_FAILURE
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_StubDdc(u8 DeviceAddress, u16 ByteCount, u8* BufferPtr,
+                             u8 Stop, void* RefPtr)
+{
+	Xil_AssertNonvoidAlways();
+	Xil_AssertNonvoid(DeviceAddress);
+	Xil_AssertNonvoid(ByteCount);
+	Xil_AssertNonvoid(BufferPtr != NULL);
+	Xil_AssertNonvoid(Stop);
+	Xil_AssertNonvoid(RefPtr != NULL);
+
+	return XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a dummy called as long as there is no valid
+* authenticated handler set. It always returns an error.
+*
+* @param  RefPtr is the reference pointer for the handler.
+*
+* @return XST_FAILURE
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_StubCallback(void* RefPtr)
+{
+	Xil_AssertVoidAlways();
+	Xil_AssertVoid(RefPtr != NULL);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pseudo random 64-bit value for Rtx as part of the
+* HDCP22 TX initiation message. If appropriate it is overwritten with a test
+* vector.
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  RtxPtr is a 64-bit random value;
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_GenerateRtx(XHdcp22_Tx *InstancePtr, u8* RtxPtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* get a 64 bits random number */
+	XHdcp22Tx_GenerateRandom(InstancePtr, XHDCP22_TX_RTX_SIZE, RtxPtr);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	XHdcp22Tx_TestGenerateRtx(InstancePtr, RtxPtr);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pseudo random 128-bit value for Km as part of the HDCP22 TX
+* initiation message. If appropriate it is overwritten with a test vector.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  KmPtr is a pointer to a 128 bits random value.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_GenerateKm(XHdcp22_Tx *InstancePtr, u8* KmPtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* get a 128 bits random number */
+	XHdcp22Tx_GenerateRandom(InstancePtr, XHDCP22_TX_KM_SIZE, KmPtr);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	XHdcp22Tx_TestGenerateKm(InstancePtr, KmPtr);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pseudo random 64-bit value for Rn as part
+* of the locality check.
+* If appropriate it is overwritten with a test vector.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  KmPtr is a pointer to a 256 bits random seed value.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_GenerateKmMaskingSeed(XHdcp22_Tx *InstancePtr,
+                                             u8* SeedPtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* get a 128 bits random number */
+	XHdcp22Tx_GenerateRandom(InstancePtr, XHDCP22_TX_KM_MSK_SEED_SIZE, SeedPtr);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	XHdcp22Tx_TestGenerateKmMaskingSeed(InstancePtr, SeedPtr);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pseudo random 64-bit value for Rn as part of the
+* HDCP22 TX locality check. If appropriate it is overwritten with a test vector.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  RnPtr is a pointer to a 64 bits random value.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_GenerateRn(XHdcp22_Tx *InstancePtr, u8* RnPtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* get a 128 bits random number */
+	XHdcp22Tx_GenerateRandom(InstancePtr, XHDCP22_TX_RN_SIZE, RnPtr);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	XHdcp22Tx_TestGenerateRn(InstancePtr, RnPtr);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pseudo random 128-bit value for Ks as part of the HDCP22 TX
+* session key exchange message. If appropriate it is overwritten with a test vector.
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  KsPtr is a 128-bit random value;
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_GenerateKs(XHdcp22_Tx *InstancePtr, u8* KsPtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* get a 64 bits random number */
+	XHdcp22Tx_GenerateRandom(InstancePtr, XHDCP22_TX_KS_SIZE, KsPtr);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	XHdcp22Tx_TestGenerateKs(InstancePtr, KsPtr);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a pseudo random 64-bit value for Riv as part of the HDCP22 TX
+* session key exchange message. If appropriate it is overwritten with a test vector.
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  RivPtr is a 64-bit random value;
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_GenerateRiv(XHdcp22_Tx *InstancePtr, u8* RivPtr)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* get a 64 bits random number */
+	XHdcp22Tx_GenerateRandom(InstancePtr, XHDCP22_TX_RIV_SIZE, RivPtr);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	XHdcp22Tx_TestGenerateRiv(InstancePtr, RivPtr);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the DCP LLC public key
+* If appropriate it returns a test vector.
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  RivPtr is a 64-bit random value;
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static const u8* XHdcp22Tx_GetKPubDpc(XHdcp22_Tx *InstancePtr)
+{
+	const u8* KPubDpcPtr = NULL;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#ifdef _XHDCP22_TX_TEST_
+	/* Let the test module decide if it should be overwritten with a test vector */
+	KPubDpcPtr = XHdcp22Tx_TestGetKPubDpc(InstancePtr);
+#endif
+
+	if (KPubDpcPtr == NULL) {
+		KPubDpcPtr = XHdcp22_Tx_KpubDcp;
+	}
+
+	return KPubDpcPtr;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function starts the timer needed for checking the HDCP22 Receive status
+* register. In case the timer is started to receive a message,
+* the MsgAvailable flag is reset.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  TimeOut_mSec is the timeout for the next status update.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_StartTimer(XHdcp22_Tx *InstancePtr, u32 TimeOut_mSec,
+                                u8 ReasonId)
+{
+	u32 Ticks = (u32)(InstancePtr->Timer.TmrCtr.Config.SysClockFreqHz / 1000000) * TimeOut_mSec * 1000;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	InstancePtr->Timer.TimerExpired = (FALSE);
+	InstancePtr->Timer.ReasonId = ReasonId;
+	InstancePtr->Timer.InitialTicks = Ticks;
+
+	/* If the timer was started for receiving a message,
+	 * the message available flag must be reset */
+	if (ReasonId != XHDCP22_TX_TS_UNDEFINED &&
+	    ReasonId != XHDCP22_TX_TS_RX_REAUTH_CHECK &&
+	    ReasonId != XHDCP22_TX_TS_WAIT_FOR_CIPHER) {
+		InstancePtr->Info.MsgAvailable = (FALSE);
+	}
+
+#ifndef _XHDCP22_TX_DISABLE_TIMEOUT_CHECKING_
+#ifdef _XHDCP22_TX_TEST_
+	if (InstancePtr->Test.TestMode == XHDCP22_TX_TESTMODE_UNIT) {
+		XHdcp22Tx_TimerHandler(InstancePtr, XHDCP22_TX_TIMER_CNTR_0);
+	}
+#else
+	if (InstancePtr->Timer.TmrCtr.IsReady == (FALSE)) {
+		return XST_FAILURE;
+	}
+
+	XTmrCtr_SetResetValue(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0, Ticks);
+	XTmrCtr_Start(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0);
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_STARTIMER);
+#endif /* _XHDCP22_TX_TEST_ */
+#endif /* _XHDCP22_TX_DISABLE_TIMEOUT_CHECKING_ */
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the current timer count value of the expiration timer.
+* register.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  TimeOut_mSec is the timeout for the next status update.
+*
+* @return
+*         - XST_SUCCESS if the timer count could be acquired.
+*         - XST_FAILURE if not.
+*
+* @note None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTimerCount(XHdcp22_Tx *InstancePtr)
+{
+	return XTmrCtr_GetValue(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function handles timer interrupts
+*
+* @param  CallbackRef refers to a XHdcp22_Tx structure
+* @param  TmrCntNumber the number of used timer.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_TimerHandler(void *CallbackRef, u8 TmrCntNumber)
+{
+	XHdcp22_Tx *InstancePtr = (XHdcp22_Tx *)CallbackRef;
+
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	if (TmrCntNumber == XHDCP22_TX_TIMER_CNTR_1) {
+		return;
+	}
+
+	/* Set timer expired signaling flag */
+	InstancePtr->Timer.TimerExpired = (TRUE);
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function can be used to change the polling value. The polling value
+* is the amount of time in milliseconds to wait between successive reads
+* of the RxStatus register. The RxStatus register is polled to determine
+* when a message is available for reading during authentication or during
+* the link integrity check phase to determine when to issue re-authentication.
+* The polling value needs to be at most 20ms to account for the locality
+* check.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  PollingValue is the polling interval defined in milliseconds
+*         - 0 : Always Poll
+*         - 1 : Poll after 1ms
+*         - 2 : Poll after 2ms
+*         - 3 : Poll after 3ms etc...
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_SetMessagePollingValue(XHdcp22_Tx *InstancePtr, u32 PollingValue)
+{
+	InstancePtr->Info.PollingValue = PollingValue;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function waits for receiving expected messages from the receiver.
+* If the timer is not started, it will be started.
+* This has to be used to avoid blocking waits, and allows polling to return
+* to allow the main thread to continue handling other requests.
+* Some receivers require to read status as soon as possible otherwise the
+* receiver may request for a re-authentication so we must poll!
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  ExpectedSize indicates the expected message size in bytes.
+* @param  ReadyBit indicates if the repeater ready bit from RxStatus register
+*         should be used or the specified ExpectedSize.
+*         - TRUE Ready bit from RxStatus is used. ExpectedSize will be ignored.
+*         - FALSE ExpectedSize is used. Ready bit from RxStatus will be ignored.
+*
+* @return
+*         - XST_SUCCESS if no problems
+*         - XST_FAILURE if the receiver has timed out
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WaitForReceiver(XHdcp22_Tx *InstancePtr, int ExpectedSize, u8 ReadyBit)
+{
+	/*
+	 * Timer is counting down.
+	 * The interval count is the number of clock ticks for a polling interval.
+	 * The RxStatus register is read each time the difference between the
+	 * previous poll count and the current timer count is greater than
+	 * or equal to the interval count.
+	 */
+	u32 TimerCount = 0;
+	u32 IntervalCount = InstancePtr->Info.PollingValue *
+		((u32)InstancePtr->Timer.TmrCtr.Config.SysClockFreqHz / 1000);
+
+#ifdef _XHDCP22_TX_TEST_
+	if (XHdcp22Tx_TestSimulateTimeout(InstancePtr) == TRUE) {
+		return XST_FAILURE;
+	}
+#endif
+
+#ifdef _XHDCP22_TX_TEST_
+	/* If the timeout flag is disabled, we disable the timer and keep on polling */
+	if ((InstancePtr->Test.TestFlags & XHDCP22_TX_TEST_NO_TIMEOUT) == XHDCP22_TX_TEST_NO_TIMEOUT) {
+		if (InstancePtr->Timer.TmrCtr.IsStartedTmrCtr0) {
+			XTmrCtr_Stop(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0);
+		}
+		XHdcp22Tx_ReadRxStatus(InstancePtr);
+		InstancePtr->Timer.TimerExpired = (FALSE);
+		if (((ReadyBit == FALSE) && ((InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK) == ExpectedSize)) ||
+			((ReadyBit == TRUE)  &&  (InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_READY_MASK))){
+			/* Set timer expired flag to signal we've finished waiting */
+			XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSGAVAILABLE);
+			InstancePtr->Timer.TimerExpired = (TRUE);
+			InstancePtr->Info.MsgAvailable = (TRUE);
+		}
+
+		return XST_SUCCESS;
+	}
+#endif
+
+	/* busy waiting...*/
+	if (InstancePtr->Timer.TimerExpired == (FALSE)) {
+
+		/* Poll if requested */
+		/* Read current timer count */
+		TimerCount = XHdcp22Tx_GetTimerCount(InstancePtr);
+
+		/* Apply polling value: 0=poll always, 1=poll after 1ms, etc... */
+		if ((InstancePtr->Info.PollingValue == 0) ||
+			((InstancePtr->Timer.InitialTicks - TimerCount) >= IntervalCount))
+		{
+			/* Update InitialTicks to the current counter value */
+			InstancePtr->Timer.InitialTicks = TimerCount;
+
+			/* Read Rx status. */
+			XHdcp22Tx_ReadRxStatus(InstancePtr);
+
+			if (((ReadyBit == FALSE) && ((InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK) == ExpectedSize)) ||
+				(((ReadyBit == TRUE) && (InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_READY_MASK)) &&
+				((InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK) > 0))) {
+
+				/* Stop the hardware timer */
+				XTmrCtr_Stop(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_0);
+
+				/* Set timer expired flag and MsgAvailable flag to signal we've finished waiting */
+				XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSGAVAILABLE);
+				InstancePtr->Timer.TimerExpired = (TRUE);
+				InstancePtr->Info.MsgAvailable = (TRUE);
+			}
+		}
+		return XST_SUCCESS;
+	}
+
+	/* timer expired: waiting done...check size in the status */
+	if (((ReadyBit == FALSE) && ((InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK) == ExpectedSize)) ||
+		((ReadyBit == TRUE) && (InstancePtr->Info.RxStatus & XHDCP22_TX_RXSTATUS_READY_MASK))) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSGAVAILABLE);
+		InstancePtr->Info.MsgAvailable = (TRUE);
+		return XST_SUCCESS;
+	}
+
+	/* The receiver has timed out...and the data size does not match
+	 * the expected size! */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_TIMEOUT);
+	return XST_FAILURE;
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function reads RxStatus from the DDC channel. If the read
+* is not successful it will default to an RxStatus value of 0xFFFF
+* to initiate re-authentication.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  MsgBufferPtr the buffer to use for messaging.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_ReadRxStatus(XHdcp22_Tx *InstancePtr)
+{
+	u8 DdcBuf[2];
+	int Status = XST_FAILURE;
+
+	/* Set the RxStatus register address */
+	DdcBuf[0] = XHDCP22_TX_HDCPPORT_RXSTATUS_OFFSET;
+
+	Status = InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS, 1, DdcBuf, (FALSE),
+	                      InstancePtr->DdcHandlerRef);
+
+	/* If write fails, request re-authentication */
+	if (Status != XST_SUCCESS) {
+		InstancePtr->Info.RxStatus = XHDCP22_TX_INVALID_RXSTATUS;
+		return;
+	}
+
+	Status = InstancePtr->DdcRead(XHDCP22_TX_DDC_BASE_ADDRESS, sizeof(DdcBuf),
+					DdcBuf, (TRUE), InstancePtr->DdcHandlerRef);
+
+	/* If read fails, request re-authentication */
+	if (Status != XST_SUCCESS) {
+		InstancePtr->Info.RxStatus = XHDCP22_TX_INVALID_RXSTATUS;
+		return;
+	}
+
+	InstancePtr->Info.RxStatus = DdcBuf[0] | (DdcBuf[1] << 8);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function handles authentication failures.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_HandleAuthenticationFailed(XHdcp22_Tx * InstancePtr)
+{
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_AUTHENTICATION_BUSY;
+
+     /* Run user callback */
+	if (InstancePtr->IsUnauthenticatedCallbackSet)
+		InstancePtr->UnauthenticatedCallback(InstancePtr->UnauthenticatedCallbackRef);
+
+	/* HDCP2Version */
+	InstancePtr->IsReceiverHDCP2Capable = XHdcp22Tx_IsDwnstrmCapable(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function handles reauthentication requests.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_HandleReauthenticationRequest(XHdcp22_Tx * InstancePtr)
+{
+	InstancePtr->Info.ReAuthenticationRequested = (TRUE);
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_REAUTHENTICATE_REQUESTED;
+
+	/* Reset cipher */
+	XHdcp22Tx_DisableEncryption(InstancePtr);
+	XHdcp22Cipher_Disable(&InstancePtr->Cipher);
+	XHdcp22Cipher_Enable(&InstancePtr->Cipher);
+
+	/* Increment re-authentication request count */
+	InstancePtr->Info.ReauthRequestCnt++;
+
+	/* Clear Topology Available flag */
+	InstancePtr->Info.IsTopologyAvailable = (FALSE);
+
+	if (InstancePtr->IsUnauthenticatedCallbackSet)
+		InstancePtr->UnauthenticatedCallback(InstancePtr->UnauthenticatedCallbackRef);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function issues a AKE_Init message
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  MsgBufferPtr the buffer to use for messaging.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteAKEInit(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22_Tx_DDCMessage* MsgPtr = (XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_TX_AKEINIT);
+
+	/* Increment authentication request count */
+	InstancePtr->Info.AuthRequestCnt++;
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_AKE_INIT;
+
+	/* Generate Rtx and add to the buffer*/
+	XHdcp22Tx_GenerateRtx(InstancePtr, InstancePtr->Info.Rtx);
+
+	memcpy(&MsgPtr->Message.AKEInit.Rtx, InstancePtr->Info.Rtx,
+	       sizeof(MsgPtr->Message.AKEInit.Rtx));
+	/* Add TxCaps to the buffer*/
+	memcpy(&MsgPtr->Message.AKEInit.TxCaps, XHdcp22_Tx_TxCaps,
+	       sizeof(MsgPtr->Message.AKEInit.TxCaps));
+
+	/* Execute write */
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+	                             sizeof(XHdcp22_Tx_AKEInit)+1,
+	                             (u8 *)MsgPtr, (TRUE),
+	                             InstancePtr->DdcHandlerRef);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function issues a AKE_No_Stored_km message
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  MsgBufferPtr the buffer containing the certificate and re-used
+*         for sending the message.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteAKENoStoredKm(XHdcp22_Tx *InstancePtr,
+                                         const XHdcp22_Tx_PairingInfo *PairingInfoPtr,
+                                         const XHdcp22_Tx_CertRx *CertificatePtr)
+{
+	XHdcp22_Tx_DDCMessage* MsgPtr = (XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+	u8 MaskingSeed[XHDCP22_TX_KM_MSK_SEED_SIZE];
+	u8 EKpubKm[XHDCP22_TX_E_KPUB_KM_SIZE];
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_ENCRYPT_KM_DONE);
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_AKE_NO_STORED_KM;
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_ENCRYPT_KM);
+
+	/* Get the seed for the masking RSA-OEAP masking function */
+	XHdcp22Tx_GenerateKmMaskingSeed(InstancePtr, MaskingSeed);
+
+	/* Encrypt, pass certificate (1st value is messageId) */
+	XHdcp22Tx_EncryptKm(CertificatePtr, PairingInfoPtr->Km, MaskingSeed, EKpubKm);
+	memcpy(MsgPtr->Message.AKENoStoredKm.EKpubKm, EKpubKm,
+	       sizeof(MsgPtr->Message.AKENoStoredKm.EKpubKm));
+
+	/* Execute write */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_TX_NOSTOREDKM);
+
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+	                      sizeof(XHdcp22_Tx_AKENoStoredKm)+1, (u8 *)MsgPtr,
+	                      (TRUE), InstancePtr->DdcHandlerRef);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function issues a AKE_Stored_km message
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  MsgBufferPtr the buffer to use for messaging.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteAKEStoredKm(XHdcp22_Tx *InstancePtr,
+                                       const XHdcp22_Tx_PairingInfo *PairingInfoPtr)
+{
+	XHdcp22_Tx_DDCMessage* MsgPtr =
+	                       (XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_TX_STOREDKM);
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_AKE_STORED_KM;
+
+	memcpy(MsgPtr->Message.AKEStoredKm.EKhKm, PairingInfoPtr->Ekh_Km,
+	       sizeof(MsgPtr->Message.AKEStoredKm.EKhKm));
+	memcpy(MsgPtr->Message.AKEStoredKm.Rtx, PairingInfoPtr->Rtx,
+	       sizeof(MsgPtr->Message.AKEStoredKm.Rtx));
+	memcpy(MsgPtr->Message.AKEStoredKm.Rrx, PairingInfoPtr->Rrx,
+	       sizeof(MsgPtr->Message.AKEStoredKm.Rrx));
+
+	/* Execute write */
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+	                      sizeof(XHdcp22_Tx_AKEStoredKm)+1, (u8 *)MsgPtr,
+	                      (TRUE), InstancePtr->DdcHandlerRef);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function write a locality check has value.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  RnPtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteLcInit(XHdcp22_Tx *InstancePtr, const u8* RnPtr)
+{
+	XHdcp22_Tx_DDCMessage* MsgPtr =
+	                      (XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG,
+	                XHDCP22_TX_LOG_DBG_TX_LCINIT);
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_LC_INIT;
+
+	memcpy(MsgPtr->Message.LCInit.Rn, RnPtr, sizeof(MsgPtr->Message.LCInit.Rn));
+
+	/* Execute write */
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+	                      sizeof(XHdcp22_Tx_LCInit)+1, (u8 *)MsgPtr,
+	                      (TRUE), InstancePtr->DdcHandlerRef);
+}
+
+/******************************************************************************/
+/**
+*
+* This function sends the session key to the receiver.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  EdkeyKsPtr is a pointer to the encrypted session key.
+* @param  RivPtr is a pointer to the random IV pair.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteSkeSendEks(XHdcp22_Tx *InstancePtr,
+                                      const u8 *EdkeyKsPtr, const u8 *RivPtr)
+{
+	XHdcp22_Tx_DDCMessage* MsgPtr =
+	                      (XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_TX_EKS);
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_SKE_SEND_EKS;
+
+	memcpy(MsgPtr->Message.SKESendEks.EDkeyKs, EdkeyKsPtr,
+	       sizeof(MsgPtr->Message.SKESendEks.EDkeyKs));
+
+	memcpy(MsgPtr->Message.SKESendEks.Riv, RivPtr,
+	       sizeof(MsgPtr->Message.SKESendEks.Riv));
+
+	/* Execute write */
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+	                      sizeof(XHdcp22_Tx_SKESendEks)+1, (u8 *)MsgPtr,
+	                      (TRUE), InstancePtr->DdcHandlerRef);
+}
+
+/******************************************************************************/
+/**
+*
+* This function sends the Receiver ID List acknowledgement to the repeater.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  VPtr is a pointer to the least significant 128-bits of V.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteRepeaterAuth_Send_Ack(XHdcp22_Tx *InstancePtr, const u8 *VPtr)
+{
+	XHdcp22_Tx_DDCMessage* MsgPtr =
+		(XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_REPEATAUTH_SEND_ACK;
+
+	memcpy(MsgPtr->Message.RepeatAuthSendAck.V, VPtr,
+		sizeof(MsgPtr->Message.RepeatAuthSendAck.V));
+
+	/* Execute write */
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+	                      sizeof(XHdcp22_Tx_RepeatAuthSendAck) + 1, (u8 *)MsgPtr,
+	                      (TRUE), InstancePtr->DdcHandlerRef);
+}
+
+/******************************************************************************/
+/**
+*
+* This function sends the Content Stream Type to the repeater.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return
+*         - XST_SUCCESS if writing succeeded
+*         - XST_FAILURE if failed to write
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_WriteRepeaterAuth_Stream_Manage(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22_Tx_PairingInfo *PairingInfoPtr =
+		(XHdcp22_Tx_PairingInfo *)InstancePtr->Info.StateContext;
+	XHdcp22_Tx_DDCMessage* MsgPtr =
+		(XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET;
+	MsgPtr->Message.MsgId = XHDCP22_TX_REPEATAUTH_STREAM_MANAGE;
+
+	/* Value is sent in big endian format */
+	MsgPtr->Message.RepeatAuthStreamManage.SeqNum_M[0] = (InstancePtr->Info.SeqNum_M >> 16) & 0xFF; // MSB
+	MsgPtr->Message.RepeatAuthStreamManage.SeqNum_M[1] = (InstancePtr->Info.SeqNum_M >> 8)  & 0xFF;
+	MsgPtr->Message.RepeatAuthStreamManage.SeqNum_M[2] =  InstancePtr->Info.SeqNum_M        & 0xFF; // LSB
+
+	/* The parameter K is always set to 0x1 by the HDCP transmitter */
+	/* Value is sent in big endian format */
+	MsgPtr->Message.RepeatAuthStreamManage.K[0] = 0x0; // MSB
+	MsgPtr->Message.RepeatAuthStreamManage.K[1] = 0x1; // LSB
+
+	/* StreamID_Type = STREAM_ID || Type */
+	/* Value is sent in big endian format */
+	MsgPtr->Message.RepeatAuthStreamManage.StreamID_Type[0] = 0x0; // STREAM_ID: must always be 0x0
+	MsgPtr->Message.RepeatAuthStreamManage.StreamID_Type[1] = (u8)InstancePtr->Info.ContentStreamType; // Stream Type
+
+	/* To make verifying the MPrime from the repeater easier,
+	 * the M is calculated and stored before executing the write */
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_COMPUTE_M);
+	XHdcp22Tx_ComputeM(InstancePtr->Info.Rn,
+		InstancePtr->Info.Rrx,
+		InstancePtr->Info.Rtx,
+		MsgPtr->Message.RepeatAuthStreamManage.StreamID_Type,
+		MsgPtr->Message.RepeatAuthStreamManage.K,
+		MsgPtr->Message.RepeatAuthStreamManage.SeqNum_M,
+		PairingInfoPtr->Km,
+		InstancePtr->Info.M);
+	XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_COMPUTE_M_DONE);
+
+	/* Increment the M */
+	InstancePtr->Info.SeqNum_M += 1;
+	/* Seq_num_M is 3 bytes, the variable is a u32.
+	 * Mask out the most-significant byte.
+	 */
+	InstancePtr->Info.SeqNum_M &= 0xFFF;
+
+	/* Execute write */
+	return InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS,
+		XHDCP22_TX_REPEATAUTH_STREAM_MANAGE_SIZE + 1, (u8 *)MsgPtr,
+		(TRUE), InstancePtr->DdcHandlerRef);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function receives a message send by HDCP22 RX.
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  MessageId the message Id of the expected message.
+* @param  MessageSize the size of the expected message.
+*
+* @return
+*         - XST_SUCCESS if the message size and id are as expected.
+*         - XST_FAILURE if if the message size and id are incorrect.
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_ReceiveMsg(XHdcp22_Tx *InstancePtr, u8 MessageId,
+                                u32 MessageSize)
+{
+	int Result = XST_SUCCESS;
+	XHdcp22_Tx_DDCMessage* MsgPtr =
+	                       (XHdcp22_Tx_DDCMessage*)InstancePtr->MessageBuffer;
+
+	u32 ReceivedSize = InstancePtr->Info.RxStatus &
+	                   XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK;
+
+	/* Check if the received size matches the expected size. */
+	if (ReceivedSize != MessageSize) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_READ_FAIL);
+		return XST_FAILURE;
+	}
+
+	MsgPtr->DdcAddress = XHDCP22_TX_HDCPPORT_READ_MSG_OFFSET;
+	/* Set the Expected msg ID in the buffer for testing purposes */
+	MsgPtr->Message.MsgId = MessageId;
+
+	Result = InstancePtr->DdcWrite(XHDCP22_TX_DDC_BASE_ADDRESS, 1,
+	                               &MsgPtr->DdcAddress, (FALSE),
+	                               InstancePtr->DdcHandlerRef);
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_READ_FAIL);
+		return Result;
+	}
+
+	/* Reading starts on message id */
+	Result = InstancePtr->DdcRead(XHDCP22_TX_DDC_BASE_ADDRESS, ReceivedSize,
+	                              (u8 *)&MsgPtr->Message.MsgId,
+	                              (TRUE), InstancePtr->DdcHandlerRef);
+	if (Result != XST_SUCCESS) {
+		XHdcp22Tx_LogWr(InstancePtr, XHDCP22_TX_LOG_EVT_DBG, XHDCP22_TX_LOG_DBG_MSG_READ_FAIL);
+		return Result;
+	}
+
+	/* Check if the received message id matches the expected message id */
+	if (MsgPtr->Message.MsgId != MessageId)
+		return XST_FAILURE;
+
+	return XST_SUCCESS;
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function clear the global pairing info structure, so every
+* HDCP2.2 receiver will have to go through the 'no stored km' sequence
+* to authenticate.
+*
+* @param   InstancePtr is a pointer to the XHdcp22Tx core instance.
+*
+* @return  XST_SUCCESS
+*
+* @note    None.
+*
+******************************************************************************/
+int XHdcp22Tx_ClearPairingInfo(XHdcp22_Tx *InstancePtr)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	memset(InstancePtr->Info.PairingInfo, 0x00,
+	       sizeof(InstancePtr->Info.PairingInfo));
+
+	return XST_SUCCESS;
+}
+/*****************************************************************************/
+/**
+*
+* This function gets a stored pairing info entry from the storage.
+*
+* @param  ReceiverId is a pointer to a 5-byte receiver Id.
+*
+* @return A pointer to the found ReceiverId or NULL if the pairing info wasn't
+*         stored yet.
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_PairingInfo *XHdcp22Tx_GetPairingInfo(XHdcp22_Tx *InstancePtr,
+	                                                     const u8 *ReceiverId)
+{
+	int i = 0;
+	u8 IllegalRecvID[] = {0x0, 0x0, 0x0, 0x0, 0x0};
+	XHdcp22_Tx_PairingInfo * PairingInfoPtr = NULL;
+
+	/* Check for illegal Receiver ID */
+	if (memcmp(ReceiverId, IllegalRecvID, XHDCP22_TX_CERT_RCVID_SIZE) == 0) {
+		return NULL;
+	}
+
+	for (i=0; i<XHDCP22_TX_MAX_STORED_PAIRINGINFO; i++) {
+		PairingInfoPtr = &InstancePtr->Info.PairingInfo[i];
+		if (memcmp(ReceiverId, PairingInfoPtr->ReceiverId,
+		           XHDCP22_TX_CERT_RCVID_SIZE) == 0) {
+			return PairingInfoPtr;
+		}
+	}
+	return NULL;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function updates a pairing info entry in the storage.
+*
+* @param  PairingInfo is a pointer to a pairing info structure.
+*
+* @return
+*         - XST_SUCCESS if there was enough room
+*         - XST_FAILURE if there was no room for this receiver
+*
+* @note   None.
+*
+******************************************************************************/
+static XHdcp22_Tx_PairingInfo *XHdcp22Tx_UpdatePairingInfo(
+	                          XHdcp22_Tx *InstancePtr,
+                              const XHdcp22_Tx_PairingInfo *PairingInfo,
+                              u8 Ready)
+{
+	int i = 0;
+	int i_match = 0;
+	u8 Match = (FALSE);
+	XHdcp22_Tx_PairingInfo * PairingInfoPtr = NULL;
+
+	/* Find slot */
+	for (i=0; i<XHDCP22_TX_MAX_STORED_PAIRINGINFO; i++) {
+
+		PairingInfoPtr = &InstancePtr->Info.PairingInfo[i];
+
+		/* Look for empty slot */
+		if ((PairingInfoPtr->Ready == FALSE) && (Match == FALSE)) {
+			i_match = i;
+			Match = (TRUE);
+		}
+
+		/* Look for match, match overrides empty slot */
+		if (memcmp(PairingInfo->ReceiverId, PairingInfoPtr->ReceiverId,
+		           XHDCP22_TX_CERT_RCVID_SIZE) == 0) {
+			i_match = i;
+			break;
+		}
+	}
+
+	PairingInfoPtr = &InstancePtr->Info.PairingInfo[i_match];
+
+	/* Copy pairing info*/
+	memcpy(PairingInfoPtr, PairingInfo, sizeof(XHdcp22_Tx_PairingInfo));
+
+	/* Set table ready */
+	PairingInfoPtr->Ready = Ready;
+
+	return PairingInfoPtr;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function invalidates a pairing info structure
+*
+* @param  ReceiverId is a pointer to a 5-byte receiver Id.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XHdcp22Tx_InvalidatePairingInfo(XHdcp22_Tx *InstancePtr,
+	                                        const u8* ReceiverId)
+{
+	XHdcp22_Tx_PairingInfo *InfoPtr = XHdcp22Tx_GetPairingInfo(InstancePtr,
+		                                                       ReceiverId);
+
+	/* do nothing if the id was not found */
+	if (InfoPtr == NULL) {
+		return;
+	}
+	/* clear the found structure */
+	memset(InfoPtr, 0x00, sizeof(XHdcp22_Tx_PairingInfo));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function adds a ReceiverID to RevocationList
+*
+* @param  InstancePtr is a pointer to the XHdcp22Tx core instance.
+* @param  ReceiverId is a pointer to a 5-byte receiver Id.
+*
+* @return None.
+*
+* @note Supposed to be called by Upstream Content Control Function
+*
+******************************************************************************/
+void XHdcp22Tx_RevokeReceiverId(XHdcp22_Tx *InstancePtr,
+				u8* ReceiverIdPtr)
+{
+	XHdcp22_Tx_RevocationList* RevocationListPtr;
+	u32 NumDevices;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(ReceiverIdPtr != NULL);
+
+	RevocationListPtr =
+			XHdcp22Tx_GetRevocationReceiverIdList(InstancePtr);
+	NumDevices = RevocationListPtr->NumDevices;
+
+	if (InstancePtr->Config.Mode != XHDCP22_TX_TRANSMITTER)
+		return;
+
+	if (!XHdcp22Tx_IsDeviceRevoked(InstancePtr, ReceiverIdPtr)) {
+		memcpy(RevocationListPtr->ReceiverId[NumDevices],
+				ReceiverIdPtr, XHDCP22_TX_SRM_RCVID_SIZE);
+		RevocationListPtr->NumDevices++;
+		InstancePtr->Info.IsRevocationListValid = TRUE;
+	}
+
+	InstancePtr->Info.IsDeviceRevoked = TRUE;
+	InstancePtr->Info.AuthenticationStatus = XHDCP22_TX_DEVICE_IS_REVOKED;
+
+	XHdcp22Tx_HandleAuthenticationFailed(InstancePtr);
+	InstancePtr->Info.CurrentState = XHDCP22_TX_STATE_A0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the DEPTH in the repeater topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   Repeater topology DEPTH.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTopologyDepth(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.Depth);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the DEVICE_COUNT in the repeater topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   DEVICE_COUNT in the repeater topology structure.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTopologyDeviceCnt(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.DeviceCnt);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the MAX_DEVICS_EXCEEDED flag in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   MAX_DEVICS_EXCEEDED flag in the repeater structure.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTopologyMaxDevsExceeded(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.MaxDevsExceeded) ? TRUE : FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the MAX_CASCADE_EXCEEDED flag in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   MAX_CASCADE_EXCEEDED flag in the repeater structure.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTopologyMaxCascadeExceeded(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.MaxCascadeExceeded) ? TRUE : FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the HDCP2_LEGACY_DEVICE_DOWNSTREAM flag in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   HDCP2_LEGACY_DEVICE_DOWNSTREAM flag in the repeater structure.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTopologyHdcp2LegacyDeviceDownstream(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.Hdcp2LegacyDeviceDownstream) ? TRUE : FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the HDCP1_DEVICE_DOWNSTREAM flag in the repeater
+* topology structure.
+*
+* @param    InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return   HDCP1_DEVICE_DOWNSTREAM flag in the repeater structure.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XHdcp22Tx_GetTopologyHdcp1DeviceDownstream(XHdcp22_Tx *InstancePtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	return (InstancePtr->Topology.Hdcp1DeviceDownstream) ? TRUE : FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function clears the log pointers
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param  Verbose allows to add debug logging.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_LogReset(XHdcp22_Tx *InstancePtr, u8 Verbose)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Log.Head = 0;
+	InstancePtr->Log.Tail = 0;
+	InstancePtr->Log.Verbose = Verbose;
+	/* Reset and start the logging timer. */
+	/* Note: This timer increments continuously and will wrap at 42 second (100 Mhz clock) */
+	if (InstancePtr->Timer.TmrCtr.IsReady == XIL_COMPONENT_IS_READY) {
+	   XTmrCtr_SetResetValue(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_1, 0);
+	   XTmrCtr_Start(&InstancePtr->Timer.TmrCtr, XHDCP22_TX_TIMER_CNTR_1);
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the time expired since a log reset was called
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return The expired logging time in useconds.
+*
+* @note   None.
+*
+******************************************************************************/
+u32 XHdcp22Tx_LogGetTimeUSecs(XHdcp22_Tx *InstancePtr)
+{
+	if (InstancePtr->Timer.TmrCtr.IsReady != XIL_COMPONENT_IS_READY)
+		return 0;
+
+	u32 PeriodUsec = (u32)InstancePtr->Timer.TmrCtr.Config.SysClockFreqHz / 1000000;
+	return 	 ( XTmrCtr_GetValue(&InstancePtr->Timer.TmrCtr,
+			   XHDCP22_TX_TIMER_CNTR_1) / PeriodUsec);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function writes HDCP TX logs into buffer.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx core instance.
+* @param  Evt specifies an action to be carried out. Please refer
+*         #XHdcp22_Tx_LogEvt enum in xhdcp22_tx.h.
+* @param  Data specifies the information that gets written into log
+*         buffer.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_LogWr(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_LogEvt Evt, u16 Data)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Evt < (XHDCP22_TX_LOG_INVALID));
+
+	if (InstancePtr->Log.Verbose == FALSE && Evt == XHDCP22_TX_LOG_EVT_DBG) {
+		return;
+	}
+
+	/* Write data and event into log buffer */
+	InstancePtr->Log.LogItems[InstancePtr->Log.Head].Data = Data;
+	InstancePtr->Log.LogItems[InstancePtr->Log.Head].LogEvent = Evt;
+	InstancePtr->Log.LogItems[InstancePtr->Log.Head].TimeStamp =
+                            XHdcp22Tx_LogGetTimeUSecs(InstancePtr);
+
+	/* Update head pointer if reached to end of the buffer */
+	if (InstancePtr->Log.Head == XHDCP22_TX_LOG_BUFFER_SIZE - 1) {
+		/* Clear pointer */
+		InstancePtr->Log.Head = 0;
+	} else {
+		/* Increment pointer */
+		InstancePtr->Log.Head++;
+	}
+
+	/* Check tail pointer. When the two pointer are equal, then the buffer
+	 * is full.In this case then increment the tail pointer as well to
+	 * remove the oldest entry from the buffer.
+	 */
+	if (InstancePtr->Log.Tail == InstancePtr->Log.Head) {
+		if (InstancePtr->Log.Tail == XHDCP22_TX_LOG_BUFFER_SIZE - 1) {
+			InstancePtr->Log.Tail = 0;
+		} else {
+			InstancePtr->Log.Tail++;
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides the log information from the log buffer.
+*
+* @param  InstancePtr is a pointer to the XHdcp22_Tx core instance.
+*
+* @return
+*         - Content of log buffer if log pointers are not equal.
+*         - Otherwise Zero.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdcp22_Tx_LogItem* XHdcp22Tx_LogRd(XHdcp22_Tx *InstancePtr)
+{
+	XHdcp22_Tx_LogItem* LogPtr;
+	u16 Tail = 0;
+	u16 Head = 0;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	Tail = InstancePtr->Log.Tail;
+	Head = InstancePtr->Log.Head;
+
+	/* Check if there is any data in the log and return a NONE defined log item */
+	if (Tail == Head) {
+		LogPtr = &InstancePtr->Log.LogItems[Tail];
+		LogPtr->Data = 0;
+		LogPtr->LogEvent = XHDCP22_TX_LOG_EVT_NONE;
+		LogPtr->TimeStamp = 0;
+		return LogPtr;
+	}
+
+	LogPtr = &InstancePtr->Log.LogItems[Tail];
+
+	/* Increment tail pointer */
+	if (Tail == XHDCP22_TX_LOG_BUFFER_SIZE - 1) {
+		InstancePtr->Log.Tail = 0;
+	}
+	else {
+		InstancePtr->Log.Tail++;
+	}
+	return LogPtr;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the content of log buffer.
+*
+* @param  InstancePtr is a pointer to the HDCP22 TX core instance.
+* @param  buff is a pointer to the buffer to write to.
+* @param  buff_size is the size of the passed buffer
+*
+* @return Number of characters printed to the buffer.
+*
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_LogShow(XHdcp22_Tx *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+	XHdcp22_Tx_LogItem* LogPtr;
+	char str[255];
+	u32 TimeStampPrev = 0;
+
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+#ifdef _XHDCP22_TX_TEST_
+	if (InstancePtr->Test.TestMode == XHDCP22_TX_TESTMODE_UNIT) {
+		XHdcp22Tx_LogDisplayUnitTest(InstancePtr);
+		return;
+	}
+#endif
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"\r\n-------HDCP22 TX log start-------\r\n");
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"[Time(us):Delta(us)] <Event>\n\r");
+	strcpy(str, "UNDEFINED");
+	do {
+		/* Read log data */
+		LogPtr = XHdcp22Tx_LogRd(InstancePtr);
+
+		/* Print timestamp */
+		if(LogPtr->LogEvent != XHDCP22_TX_LOG_EVT_NONE)
+		{
+			if(LogPtr->TimeStamp < TimeStampPrev) TimeStampPrev = 0;
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"[%8u:", LogPtr->TimeStamp);
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"%8u] ", (LogPtr->TimeStamp - TimeStampPrev));
+			TimeStampPrev = LogPtr->TimeStamp;
+		}
+
+		/* Print log event */
+		switch (LogPtr->LogEvent) {
+		case (XHDCP22_TX_LOG_EVT_NONE):
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"-------HDCP22 TX log end-------\r\n\r\n");
+			break;
+		case XHDCP22_TX_LOG_EVT_STATE:
+			switch(LogPtr->Data)
+			{
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, H0)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, H1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A0)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A1_1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A1_NSK0)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A1_NSK1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A1_SK0)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A2)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A2_1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A3)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A4)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A5)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A6_A7_A8)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A6)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A7)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A8)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A9)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_STATE_, A9_1)
+				default: break;
+			};
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Current state [%s]\r\n", str);
+			break;
+		case XHDCP22_TX_LOG_EVT_POLL_RESULT:
+			switch(LogPtr->Data)
+			{
+			case XHDCP22_TX_INCOMPATIBLE_RX: strcpy(str, "INCOMPATIBLE RX"); break;
+			case XHDCP22_TX_AUTHENTICATION_BUSY: strcpy(str, "AUTHENTICATION BUSY"); break;
+			case XHDCP22_TX_AUTHENTICATED: strcpy(str, "AUTHENTICATED"); break;
+			case XHDCP22_TX_UNAUTHENTICATED: strcpy(str, "UN-AUTHENTICATED"); break;
+			case XHDCP22_TX_REAUTHENTICATE_REQUESTED: strcpy(str, "RE-AUTHENTICATION REQUESTED"); break;
+			default: break;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Poll result [%s]\r\n", str);
+			break;
+		case XHDCP22_TX_LOG_EVT_ENABLED:
+			if (LogPtr->Data == (FALSE)) {
+				strcpy(str, "DISABLED");
+			} else {
+				strcpy(str, "ENABLED");
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"State machine [%s]\r\n", str);
+			break;
+		case XHDCP22_TX_LOG_EVT_RESET:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Asserted [RESET]\r\n");
+			break;
+		case XHDCP22_TX_LOG_EVT_ENCR_ENABLED:
+			if (LogPtr->Data == (FALSE)) {
+				strcpy(str, "DISABLED");
+			} else {
+				strcpy(str, "ENABLED");
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Encryption [%s]\r\n", str);
+			break;
+		case XHDCP22_TX_LOG_EVT_TEST_ERROR:
+			switch(LogPtr->Data)
+			{
+			case XHDCP22_TX_AKE_NO_STORED_KM:
+			      strcpy(str, "EkpubKm does not match the calculated value.");
+			      break;
+			case XHDCP22_TX_SKE_SEND_EKS:
+			      strcpy(str, "EdkeyKs does not match the calculated value.");
+			      break;
+			case XHDCP22_TX_MSG_UNDEFINED:
+			      strcpy(str, "Trying to write an unexpected message.");
+			      break;
+			default: break;
+			};
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Test error [%s]\r\n", str);
+			break;
+		case XHDCP22_TX_LOG_EVT_LCCHK_COUNT:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Locality check count [%d]\r\n", LogPtr->Data);
+			break;
+		case XHDCP22_TX_LOG_EVT_STRMMNGCHK_COUNT:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Content Stream Management check count [%d]\r\n", LogPtr->Data);
+			break;
+		case XHDCP22_TX_LOG_EVT_DBG:
+			switch(LogPtr->Data)
+			{
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, STARTIMER)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, MSGAVAILABLE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TX_AKEINIT)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RX_CERT)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, VERIFY_SIGNATURE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, VERIFY_SIGNATURE_PASS)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, VERIFY_SIGNATURE_FAIL)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, DEVICE_IS_REVOKED)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, ENCRYPT_KM)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, ENCRYPT_KM_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TX_NOSTOREDKM)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TX_STOREDKM)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RX_H1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RX_EKHKM)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_H)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_H_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPARE_H_FAIL)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TX_LCINIT)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RX_L1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_L)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_L_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPARE_L_FAIL)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_EDKEYKS)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_EDKEYKS_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TX_EKS)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RX_RCVIDLIST)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_V)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_V_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPARE_V_FAIL)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RX_M1)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_M)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, COMPUTE_M_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, CHECK_REAUTH)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TIMEOUT)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, TIMESTAMP)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, AES128ENC)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, AES128ENC_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, SHA256HASH)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, SHA256HASH_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, OEAPENC)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, OEAPENC_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RSAENC)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, RSAENC_DONE)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, MSG_WRITE_FAIL)
+				XHDCP22_TX_CASE_TO_STR_PRE(XHDCP22_TX_LOG_DBG_, MSG_READ_FAIL)
+				default: break;
+			};
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Debug: Event [%s]\r\n", str);
+			break;
+		case XHDCP22_TX_LOG_EVT_USER:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"User: %d\r\n", LogPtr->Data);
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Unknown log event\r\n");
+			break;
+		}
+	} while (LogPtr->LogEvent != XHDCP22_TX_LOG_EVT_NONE);
+
+	return strSize;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the state machine information.
+*
+* @param  InstancePtr is a pointer to the HDCP22 TX core instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_Info(XHdcp22_Tx *InstancePtr)
+{
+	XDEBUG_PRINTF("Status : ");
+	if (XHdcp22Tx_IsEnabled(InstancePtr)) {
+		switch (InstancePtr->Info.AuthenticationStatus) {
+			case XHDCP22_TX_INCOMPATIBLE_RX :
+				XDEBUG_PRINTF("RX is incompatible.\n\r");
+			break;
+
+			case XHDCP22_TX_AUTHENTICATION_BUSY :
+				XDEBUG_PRINTF("Busy Authentication.\n\r");
+			break;
+
+			case XHDCP22_TX_REAUTHENTICATE_REQUESTED :
+				XDEBUG_PRINTF("Re-authentication Requested.\n\r");
+			break;
+
+			case XHDCP22_TX_UNAUTHENTICATED :
+				XDEBUG_PRINTF("Not Authenticated.\n\r");
+			break;
+
+			case XHDCP22_TX_AUTHENTICATED :
+				XDEBUG_PRINTF("Authenticated.\n\r");
+			break;
+
+            case XHDCP22_TX_DEVICE_IS_REVOKED :
+            	XDEBUG_PRINTF("Device Revoked.\n\r");
+			break;
+
+            case XHDCP22_TX_NO_SRM_LOADED :
+            	XDEBUG_PRINTF("No SRM Loaded.\n\r");
+			break;
+
+			default :
+				XDEBUG_PRINTF("Unknown state.\n\r");
+			break;
+		}
+	} else {
+		XDEBUG_PRINTF("Core is disabled.\n\r");
+	}
+
+	XDEBUG_PRINTF("Encryption : ");
+	if (XHdcp22Tx_IsEncryptionEnabled(InstancePtr)) {
+		XDEBUG_PRINTF("Enabled.\n\r");
+	} else {
+		XDEBUG_PRINTF("Disabled.\n\r");
+	}
+
+	XDEBUG_PRINTF("Repeater: ");
+	if (XHdcp22Tx_IsRepeater(InstancePtr)) {
+		if (InstancePtr->Topology.MaxDevsExceeded)
+			XDEBUG_PRINTF("MaxDevsExceeded, ");
+
+		if (InstancePtr->Topology.MaxCascadeExceeded)
+			XDEBUG_PRINTF("MaxCascadeExceeded, ");
+
+		if (InstancePtr->Topology.Hdcp2LegacyDeviceDownstream)
+			XDEBUG_PRINTF("Hdcp2LegacyDeviceDownstream, ");
+
+		if (InstancePtr->Topology.Hdcp1DeviceDownstream)
+			XDEBUG_PRINTF("Hdcp1DeviceDownstream, ");
+
+		XDEBUG_PRINTF("Depth=%d, ", InstancePtr->Topology.Depth);
+		XDEBUG_PRINTF("DeviceCnt=%d, ", InstancePtr->Topology.DeviceCnt);
+		XDEBUG_PRINTF("StreamType=%d\n\r", InstancePtr->Info.ContentStreamType);
+	} else {
+		XDEBUG_PRINTF("Disabled.\n\r");
+	}
+
+	XDEBUG_PRINTF("Auth Requests: %d\n\r", InstancePtr->Info.AuthRequestCnt);
+	XDEBUG_PRINTF("Reauth Requests: %d\n\r", InstancePtr->Info.ReauthRequestCnt);
+	XDEBUG_PRINTF("Polling Interval: %d ms\n\r", InstancePtr->Info.PollingValue);
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx.h
@@ -0,0 +1,631 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_tx.h
+* @{
+* @details
+*
+* This is the main header file for Xilinx HDCP 2.2 Transmiter device driver.
+* The HDCP 2.2 Transmitter driver implements the authentication state machine.
+* It consists of:
+* - A state machine handling the states as specified in the HDCP revision 2.2
+*   specification.
+* - Functionality for checking if the HDCP 2.2 Receiver sink does respond within
+*   specified times.
+* - Message handling from/to the HDCP 2.2 receiver sink.
+* - Logging functionality including time stamps.
+
+* <b>Interrupts </b>
+*
+* The driver uses a hardware timer interrupt. The interrupt controller that should
+* be used, must be passed with the #XHdcp22Tx_SetInterruptController function.
+*
+* Application developer needs to register interrupt handler with the processor,
+* within their examples. Whenever processor calls registered application's
+* interrupt handler associated with interrupt id, application's interrupt
+* handler needs to call appropriate peripheral interrupt handler reading
+* peripheral's Status register.
+*
+* <b> Threads </b>
+*
+* This driver is not thread safe. Any needs for threads or thread mutual
+* exclusion must be satisfied by the layer above this driver.
+*
+* <b> Asserts </b>
+*
+* Asserts are used within all Xilinx drivers to enforce constraints on argument
+* values. Asserts can be turned off on a system-wide basis by defining at
+* compile time, the NDEBUG identifier. By default, asserts are turned on and it
+* is recommended that users leave asserts on during development.
+*
+* <b> Building the driver </b>
+*
+* The HDCP TX driver is composed of several source files. This allows the user
+* to build and link only those parts of the driver that are necessary.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     06/24/15 Initial release.
+* 1.01  MG     02/25/16 Added authenticated callback and GetVersion.
+* 2.00  MH     06/28/16 Updated for repeater downstream support.
+* 2.01  MH     02/28/17 Fixed compiler warnings.
+* 2.20  MH     04/12/17 Added function XHdcp22Tx_IsDwnstrmCapable.
+* 2.30  MH     07/06/17 Changed default polling value to 10 ms.
+* </pre>
+*
+******************************************************************************/
+#ifndef XHDCP22_TX_H
+/**  prevent circular inclusions by using protection macros */
+#define XHDCP22_TX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include <linux/string.h>
+
+
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xdebug.h"
+#include "xtmrctr.h"
+#include "xhdcp22_cipher.h"
+#include "xhdcp22_rng.h"
+
+/************************** Constant Definitions *****************************/
+
+/**
+* This value is the default polling interval defined in millseconds.
+* The polling interval defines the amount of time to wait between
+* successive reads of the RxStatus register.
+*/
+#define XHDCP22_TX_DEFAULT_RX_STATUS_POLLVALUE  10
+
+/**
+* Needed storage to transmit/receive messages to the HDCP2.2 receiver
+* This includes 1 extra byte for the DDC address used.
+*/
+#define  XHDCP22_TX_MAX_MESSAGE_SIZE    1+534
+
+/**
+* Needed storage for the Device IDs in the revocation list.
+*/
+#define XHDCP22_TX_REVOCATION_LIST_MAX_DEVICES 944
+
+/**
+* The list of maximum pairing info items to store.
+*/
+#define XHDCP22_TX_MAX_STORED_PAIRINGINFO  2
+
+/**
+* The size of the log buffer.
+*/
+#define XHDCP22_TX_LOG_BUFFER_SIZE 256
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * These constants are used to identify callback functions.
+ */
+typedef enum
+{
+	XHDCP22_TX_HANDLER_UNDEFINED,
+	XHDCP22_TX_HANDLER_DDC_WRITE,
+	XHDCP22_TX_HANDLER_DDC_READ,
+	XHDCP22_TX_HANDLER_AUTHENTICATED,
+	XHDCP22_TX_HANDLER_UNAUTHENTICATED,
+	XHDCP22_TX_HANDLER_DOWNSTREAM_TOPOLOGY_AVAILABLE,
+	XHDCP22_TX_HANDLER_INVALID
+} XHdcp22_Tx_HandlerType;
+
+/**
+* These constants specify the different states in the internal state machine.
+*/
+typedef enum
+{
+	XHDCP22_TX_STATE_H0,      /**< No Rx Attached. */
+	XHDCP22_TX_STATE_H1,      /**< Transmit Low value content. */
+	XHDCP22_TX_STATE_A0,      /**< Known HDCP2 Capable Rx. */
+	XHDCP22_TX_STATE_A1,      /**< Exchange Km. */
+	XHDCP22_TX_STATE_A1_1,    /**< substate of A1: wait for AKE_SEND_CERT. */
+	XHDCP22_TX_STATE_A1_NSK0, /**< No stored Km substate of A1: wait for AKE_SEND_H_PRIME. */
+	XHDCP22_TX_STATE_A1_NSK1, /**< No stored Km substate of A1, wait for AKE_SEND_PAIRING_INFO. */
+	XHDCP22_TX_STATE_A1_SK0,  /**< Stored substate of A1, wait for AKE_SEND_PAIRING_INFO. */
+	XHDCP22_TX_STATE_A2,      /**< Locality Check. */
+	XHDCP22_TX_STATE_A2_1,    /**< Locality Check. Receive and verify L_Prime. */
+	XHDCP22_TX_STATE_A3,      /**< Exchange Ks. */
+	XHDCP22_TX_STATE_A4,      /**< Test for repeater. */
+	XHDCP22_TX_STATE_A5,      /**< Authenticated. */
+	XHDCP22_TX_STATE_A6_A7_A8,/**< Wait for receiver ID list, verify and send acknowledgment */
+	XHDCP22_TX_STATE_A6,      /**< Wait for receiver ID list. */
+	XHDCP22_TX_STATE_A7,      /**< Verify Receiver ID List. */
+	XHDCP22_TX_STATE_A8,      /**< Send Receiver ID List acknowledgment. */
+	XHDCP22_TX_STATE_A9,      /**< Content Stream Management. */
+	XHDCP22_TX_STATE_A9_1,    /**< Content Stream Management. Receive and verify M_Prime. */
+	XHDCP22_TX_NUM_STATES     /**< Number of states in the state machine. */
+}XHdcp22_Tx_StateType;
+
+/**
+* These constants specify return values on polling with #XHdcp22Tx_Poll.
+* Depending on this return value, encryption of the HDMI signal should be
+* set to encrypted or un-encrypted. See also #XHdcp22Tx_EnableEncryption and
+* #XHdcp22Tx_DisableEncryption
+*/
+typedef enum
+{
+	XHDCP22_TX_INCOMPATIBLE_RX,          /**< A HDCP2 compatible receiver is not found. */
+	XHDCP22_TX_AUTHENTICATION_BUSY,      /**< Authentication is busy. */
+	XHDCP22_TX_AUTHENTICATED,            /**< Authentication is completed successfully. */
+	XHDCP22_TX_UNAUTHENTICATED,          /**< Authentication failed. */
+	XHDCP22_TX_REAUTHENTICATE_REQUESTED, /**< ReAuthentication requested.*/
+	XHDCP22_TX_DEVICE_IS_REVOKED,        /**< A device in the HDCP chain is revoked. */
+	XHDCP22_TX_NO_SRM_LOADED             /**< No valid SRM is loaded. */
+} XHdcp22_Tx_AuthenticationType;
+
+/**
+* These constants are used to define the content stream type.
+*/
+typedef enum {
+	XHDCP22_STREAMTYPE_0, /**< Type 0 Content Stream.
+	                        * Stream may be transmitted to all HDCP devices. */
+	XHDCP22_STREAMTYPE_1, /**< Type 1 Content Stream.
+	                        * Stream must not be transmitted to HDCP1.x devices
+	                        * and HDCP2.0 Repeaters. */
+} XHdcp22_Tx_ContentStreamType;
+
+/**
+* These constants are events as stored in the logging list.
+*/
+typedef enum {
+	XHDCP22_TX_LOG_EVT_NONE,            /**< Log Event None. */
+	XHDCP22_TX_LOG_EVT_STATE,           /**< State of the state machine. */
+	XHDCP22_TX_LOG_EVT_POLL_RESULT,     /**< Authentication result of polling. */
+	XHDCP22_TX_LOG_EVT_ENABLED,         /**< HDCP2.2 core is enabled or disabled. */
+	XHDCP22_TX_LOG_EVT_RESET,           /**< HDCP2.2 core is reset. */
+	XHDCP22_TX_LOG_EVT_ENCR_ENABLED,    /**< HDCP2.2 stream is encrypted or not. */
+	XHDCP22_TX_LOG_EVT_TEST_ERROR,      /**< An error was detected in one of the test modes. */
+	XHDCP22_TX_LOG_EVT_DBG,             /**< Log event for debugging. */
+	XHDCP22_TX_LOG_EVT_LCCHK_COUNT,     /**< Number of times Locality check has been done. */
+	XHDCP22_TX_LOG_EVT_STRMMNGCHK_COUNT,/**< Number of times Content Stream Management check has been done. */
+	XHDCP22_TX_LOG_EVT_USER,            /**< User logging. */
+	XHDCP22_TX_LOG_INVALID              /**< Last value the list, only used for checking. */
+} XHdcp22_Tx_LogEvt;
+
+/**
+ * These constants are used to define the used protocol.
+ */
+typedef enum {
+	XHDCP22_TX_HDMI,                    /**< HDMI protocol. */
+	XHDCP22_TX_DP,                      /**< Display Port protocol. */
+} XHdcp22_Tx_Protocol;
+
+/**
+ * These constants are used to define the used mode.
+ */
+typedef enum {
+	XHDCP22_TX_TRANSMITTER,             /**< Module acts as a HDCP 2.2 transmitter. */
+	XHDCP22_TX_REPEATER,                /**< Module acts as a HDCP 2.2 repeater.  */
+	XHDCP22_TX_CONVERTER                /**< Module acts as a HDCP 2.2 converter.  */
+} XHdcp22_Tx_Mode;
+
+/**
+* These constants are used to identify fields inside the topology structure
+*/
+typedef enum {
+	XHDCP22_TX_TOPOLOGY_DEPTH,
+	XHDCP22_TX_TOPOLOGY_DEVICECNT,
+	XHDCP22_TX_TOPOLOGY_MAXDEVSEXCEEDED,
+	XHDCP22_TX_TOPOLOGY_MAXCASCADEEXCEEDED,
+	XHDCP22_TX_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM,
+	XHDCP22_TX_TOPOLOGY_HDCP1DEVICEDOWNSTREAM,
+	XHDCP22_TX_TOPOLOGY_INVALID
+} XHdcp22_Tx_TopologyField;
+
+/**
+* Callback type for status.
+*
+* @param  CallbackRef is a callback reference passed in by the upper
+*         layer when setting the callback functions, and passed back to
+*         the upper layer when the callback is invoked.
+*
+* @return None.
+*
+* @note   None.
+*
+*/
+typedef void (*XHdcp22_Tx_Callback)(void *CallbackRef);
+
+/**
+* This typedef contains configuration information for the device.
+*/
+typedef struct
+{
+	/** DeviceId is the unique ID of the device. */
+	u16 DeviceId;
+	/** Base Address is the physical base address of the device's registers. */
+	UINTPTR BaseAddress;
+	/** HDMI or DP (Always HDCP22_TX_HDMI: Currently DP is not supported). */
+	int Protocol;
+	/** Future expansion. */
+	int Mode;
+	/** DeviceId of the internal used timer. */
+	u16 TimerDeviceId;
+	/** DeviceId of the used cipher. */
+	u16 CipherId;
+	/** Device Id of the random generator. */
+	u16 RngId;
+} XHdcp22_Tx_Config;
+
+/**
+ * The current state and data for internal used timer.
+ */
+typedef struct
+{
+	/** Expiration flag set when the hardware timer has interrupted. */
+	u8 TimerExpired;
+	/** Keep track of why the timer was started (message or status checking). */
+	u8 ReasonId;
+	/** Keep track of the start value of the timer. */
+	u32 InitialTicks;
+	/** The hardware timer instance.*/
+	XTmrCtr TmrCtr;
+} XHdcp22_Tx_Timer;
+
+/**
+* This typedef contains the the used keys used for authentication with stored Km.
+*/
+typedef struct {
+	u8 ReceiverId[5];    /**< Unique receiver Id. */
+	u8 RxCaps[3];        /**< Capabilities of the receiver. */
+	u8 Rtx[8];           /**< Random nonce for tx. */
+	u8 Rrx[8];           /**< Random nonce for Rx (m: Rtx || Rrx). */
+	u8 Km[16];           /**< Km. */
+	u8 Ekh_Km[16];       /**< Ekh(Km). */
+     u8 Ready;            /**< Indicates a valid entry */
+} XHdcp22_Tx_PairingInfo;
+/**
+* This typedef contains information about the HDCP22 transmitter.
+*/
+typedef struct
+{
+	XHdcp22_Tx_Protocol Protocol;       /**< Copy of configuration setting Protocol.*/
+
+	/* state handling. */
+	XHdcp22_Tx_StateType CurrentState;  /**< Current state of the internal state machine. */
+	XHdcp22_Tx_StateType PrvState;      /**< Previous state of the internal state machine. */
+	u8 Rtx[8];                          /**< Internal used Rtx. */
+	u8 Rrx[8];                          /**< Internal used Rrx. */
+	u8 Rn[8];                           /**< Internal used Rn. */
+	void *StateContext;                 /**< Context used internally by the state machine. */
+	u16  LocalityCheckCounter;          /**< Locality may attempt 1024 times. */
+	u8 MsgAvailable;                    /**< Message is available for reading. */
+
+	XHdcp22_Tx_PairingInfo PairingInfo[XHDCP22_TX_MAX_STORED_PAIRINGINFO];
+	/** The result after a call to #XHdcp22Tx_Poll. */
+	XHdcp22_Tx_AuthenticationType AuthenticationStatus;
+
+	/** Content stream type used with Content Stream Management */
+	XHdcp22_Tx_ContentStreamType ContentStreamType;
+
+	/** Sequence number M used with Content Stream Management */
+	u32 SeqNum_M;
+
+	/** Indicates if the first seq_num_M value is sent */
+	u8 SentFirstSeqNum_M;
+
+	/** Calculated M value */
+	u8 M[32];
+
+	/** Is topology info available */
+	u8 IsTopologyAvailable;
+
+	/** Content stream type is sent */
+	u8 IsContentStreamTypeSent;
+
+	/** Content stream type is set */
+	u8 IsContentStreamTypeSet;
+
+	/** Keeps track of the number of Content Stream Management checks performed */
+	u16 ContentStreamManageCheckCounter;
+
+	/** Content stream management failed */
+	u8 ContentStreamManageFailed;
+
+	/** Indicates if the first seq_num_V value is received */
+	u8 ReceivedFirstSeqNum_V;
+
+	/** Is re-authentication requested by HDCP 2.2 RX. */
+	u8 ReAuthenticationRequested;
+
+	/** HDCP RX status read on timer interrupt. */
+	u16 RxStatus;
+
+	/** Is HDCP TX enabled (state machine is active). */
+	u8 IsEnabled;
+
+	/** Is the receiver a HDCP 2.2 type. */
+	u8 IsReceiverHDCP2Capable;
+
+	/** Is the receiver a HDCP repeater */
+	u8 IsReceiverRepeater;
+
+	/** Is revocation list valid */
+	u8 IsRevocationListValid;
+
+	/** Is a device listed in the revocation list */
+	u8 IsDeviceRevoked;
+
+	/** The currently used polling value see also #XHDCP22_TX_DEFAULT_RX_STATUS_POLLVALUE. */
+	u32 PollingValue;
+
+	/** Authentication request count */
+	u32 AuthRequestCnt;
+
+	/** Re-authentication request count */
+	u32 ReauthRequestCnt;
+}XHdcp22_Tx_Info;
+
+/**
+ * This typedef is used to store logging events.
+ */
+typedef struct {
+	u8  LogEvent;       /**< Event that has been triggered. */
+	u16  Data;          /**< Optional data. */
+	u32 TimeStamp;      /**< Time stamp on when event occurred. Only used for time critical events. */
+} XHdcp22_Tx_LogItem;
+
+/**
+* This typedef contains the HDCP22 log list.
+*/
+typedef struct {
+	XHdcp22_Tx_LogItem LogItems[XHDCP22_TX_LOG_BUFFER_SIZE]; /**< Data. */
+	u16 Tail;                         /**< Tail pointer. */
+	u16 Head;                         /**< Head pointer. */
+	u8 Verbose;                       /**< Logging is extended with debug events. */
+} XHdcp22_Tx_Log;
+
+/**
+* This typedef contains the HDCP22 test parameters and settings.
+*/
+typedef struct {
+	u32 TestMode;                 /**< Current used test mode. */
+	u32 TestFlags;                /**< Current used test flags. */
+	u8 CurrentDdcAddress;         /**< Current DDC address by the testing framework. */
+} XHdcp22_Tx_Test;
+
+/**
+* This structure contains the HDCP2 Revocation information.
+*/
+typedef struct
+{
+	u32 NumDevices;
+	u8  ReceiverId[XHDCP22_TX_REVOCATION_LIST_MAX_DEVICES][5];
+} XHdcp22_Tx_RevocationList;
+
+/**
+* This structure contains the HDCP topology information.
+*/
+typedef struct
+{
+	/** Receiver ID list of all downstream devices. The list consists of
+	a contiguous set of bytes stored in big-endian order. */
+	u8  ReceiverId[32][5];
+
+	/** Repeater cascade depth. This value gives the number of attached
+	    levels through the connection topology. */
+	u8  Depth;
+
+	/** Total number of connected downstream devices. */
+	u8  DeviceCnt;
+
+	/** Flag used to indicate topology error. When set to one, more
+	    than 31 devices are attached to a downstream repeater. */
+	u8  MaxDevsExceeded;
+
+	/** Flag used to indicate topology error. When set to one, more
+	    than four levels of repeaters have been cascaded together. */
+	u8  MaxCascadeExceeded;
+
+	/** Flag used to indicate topology information. When set to one,
+	    indicates presence of an HDCP2.1-compliant Device in the topology. */
+	u8  Hdcp2LegacyDeviceDownstream;
+
+	/** Flag used to indicate topology information. When set to one,
+	    indicates presence of an HDCP1.x-compliant device in the topology. */
+	u8  Hdcp1DeviceDownstream;
+} XHdcp22_Tx_Topology;
+
+/**
+* Callback type used for calling DDC read and write functions.
+*
+* @param  DeviceAddress is the (i2c) device address of the HDCP port.
+* @param  ByteCount is the amount of data bytes in the buffer to read or write.
+* @param  BufferPtr is a pointer to a buffer that is used for reading or writing.
+* @param  Stop is a flag to control if a stop token is set or not.
+* @param  RefPtr is a callback reference passed in by the upper layer when setting
+*         the DDC reading and writing functions, and passed back to the upper layer when
+*         the callback is invoked.
+*
+* @return
+*         - XST_SUCCESS The read action was successful.
+*         - XST_FAILURE The read action failed.
+*
+* @note   None.
+*
+*/
+typedef int (*XHdcp22_Tx_DdcHandler)(u8 DeviceAddress, u16 ByteCount, u8* BufferPtr,
+             u8 Stop, void *RefPtr);
+
+/** Callback type used for pointer to single input function */
+typedef void (*XHdcp22_Tx_Callback)(void *HandlerRef);
+
+
+/**
+* The XHdcpTx driver instance data. An instance must be allocated for each
+* HDCP TX core in use.
+*/
+typedef struct
+{
+	/** Config */
+	XHdcp22_Tx_Config Config;
+	/** Is the component ready for usage. */
+	u32 IsReady;
+
+	/** Is the attached receiver HDCP2 capable. */
+	u8 IsReceiverHDCP2Capable;
+
+	/** Function pointer for reading DDC (Rx HDCP DeviceAddress: 0x74)
+	    using the XHdcp22_Tx_Ddc stucture as parameter. */
+	XHdcp22_Tx_DdcHandler DdcRead;
+	/** Set if DdcRead handler is defined. */
+	u8 IsDdcReadSet;
+
+	/** Function pointer for writing DDC (Rx HDCP DeviceAddress: 0x74)
+	    using the XHdcp22_Tx_Ddc stucture as parameter. */
+	XHdcp22_Tx_DdcHandler DdcWrite;
+	/** Set if DdcWrite handler is defined. */
+	u8 IsDdcWriteSet;
+
+	/** Reference pointer set with #XHdcp22Tx_SetCallback function. */
+	void *DdcHandlerRef;
+
+	/** Function pointer called after successful authentication */
+	XHdcp22_Tx_Callback AuthenticatedCallback;
+	/** Set if AuthenticatedCallback handler is defined. */
+	u8 IsAuthenticatedCallbackSet;
+	void *AuthenticatedCallbackRef;
+
+	/** Function pointer called after authentication failure */
+	XHdcp22_Tx_Callback UnauthenticatedCallback;
+	/** Set if UnauthenticatedCallback handler is defined. */
+	u8 IsUnauthenticatedCallbackSet;
+	void *UnauthenticatedCallbackRef;
+
+	/** Function pointer called after the downstream topology is available */
+	XHdcp22_Tx_Callback DownstreamTopologyAvailableCallback;
+	/** Set if DownstreamTopologyAvailableCallback handler is defined. */
+	u8 IsDownstreamTopologyAvailableCallbackSet;
+	void *DownstreamTopologyAvailableCallbackRef;
+
+	/** Internal used timer. */
+	XHdcp22_Tx_Timer Timer;
+
+	/** Internal used hardware random number generator. */
+	XHdcp22_Rng Rng;
+
+	/** Internal used cipher. */
+	XHdcp22_Cipher Cipher;
+
+	/** Info. */
+	XHdcp22_Tx_Info Info;
+
+	/** Logging. */
+	XHdcp22_Tx_Log Log;
+
+	/** Message buffer for messages that are sent/received. */
+	u8 MessageBuffer[XHDCP22_TX_MAX_MESSAGE_SIZE];
+
+	/** Revocation List. */
+	XHdcp22_Tx_RevocationList RevocationList;
+
+	/** Topology info. */
+	XHdcp22_Tx_Topology Topology;
+
+#ifdef _XHDCP22_TX_TEST_
+	/** Testing. */
+	XHdcp22_Tx_Test Test;
+#endif
+}XHdcp22_Tx;
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+/* Initialization function in xhdcp22_tx_sinit.c */
+XHdcp22_Tx_Config  *XHdcp22Tx_LookupConfig (u16 DeviceId);
+
+/* Initialization and control functions in xhdcp_tx.c */
+int XHdcp22Tx_CfgInitialize(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_Config *CfgPtr,
+                            UINTPTR EffectiveAddr);
+int XHdcp22Tx_Reset(XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_ClearPairingInfo(XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_Authenticate (XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_Poll(XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_Enable (XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_Disable (XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_EnableEncryption (XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_DisableEncryption (XHdcp22_Tx *InstancePtr);
+void XHdcp22Tx_EnableBlank (XHdcp22_Tx *InstancePtr);
+void XHdcp22Tx_DisableBlank (XHdcp22_Tx *InstancePtr);
+u8  XHdcp22Tx_IsEnabled (XHdcp22_Tx *InstancePtr);
+u8  XHdcp22Tx_IsEncryptionEnabled (XHdcp22_Tx *InstancePtr);
+u8  XHdcp22Tx_IsInProgress (XHdcp22_Tx *InstancePtr);
+u8  XHdcp22Tx_IsAuthenticated (XHdcp22_Tx *InstancePtr);
+u8  XHdcp22Tx_IsDwnstrmCapable (XHdcp22_Tx *InstancePtr);
+u32 XHdcp22Tx_GetVersion(XHdcp22_Tx *InstancePtr);
+
+/* Set DDC handler function pointers. */
+int XHdcp22Tx_SetCallback(XHdcp22_Tx *InstancePtr,
+                          XHdcp22_Tx_HandlerType HandlerType,
+                          void *CallbackFunc, void *CallbackRef);
+
+/* Return the internal timer instance. */
+XTmrCtr* XHdcp22Tx_GetTimer(XHdcp22_Tx *InstancePtr);
+
+/* Logging and testing */
+void XHdcp22Tx_LogReset(XHdcp22_Tx *InstancePtr, u8 Verbose);
+void XHdcp22Tx_LogWr(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_LogEvt Evt, u16 Data);
+XHdcp22_Tx_LogItem* XHdcp22Tx_LogRd(XHdcp22_Tx *InstancePtr);
+int XHdcp22Tx_LogShow(XHdcp22_Tx *InstancePtr, char *buff, int buff_size);
+u32  XHdcp22Tx_LogGetTimeUSecs(XHdcp22_Tx *InstancePtr);
+void XHdcp22Tx_SetMessagePollingValue(XHdcp22_Tx *InstancePtr, u32 PollingValue);
+void XHdcp22Tx_Info(XHdcp22_Tx *InstancePtr);
+
+/* Functions for loading authentication constants */
+void XHdcp22Tx_LoadLc128(XHdcp22_Tx *InstancePtr, const u8 *Lc128Ptr);
+
+/* SRM and revocation */
+int XHdcp22Tx_LoadRevocationTable(XHdcp22_Tx *InstancePtr, const u8 *SrmPtr);
+XHdcp22_Tx_RevocationList* XHdcp22Tx_GetRevocationReceiverIdList(XHdcp22_Tx *InstancePtr);
+u8 XHdcp22Tx_IsDeviceRevoked(XHdcp22_Tx *InstancePtr, u8 *RecvIdPtr);
+void XHdcp22Tx_RevokeReceiverId(XHdcp22_Tx *InstancePtr,
+				u8* ReceiverIdPtr);
+
+/* Functions for repeater downstream interface */
+XHdcp22_Tx_Topology *XHdcp22Tx_GetTopology(XHdcp22_Tx *InstancePtr);
+u8 *XHdcp22Tx_GetTopologyReceiverIdList(XHdcp22_Tx *InstancePtr);
+u32 XHdcp22Tx_GetTopologyField(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_TopologyField Field);
+u8 XHdcp22Tx_IsRepeater(XHdcp22_Tx *InstancePtr);
+void XHdcp22Tx_SetRepeater(XHdcp22_Tx *InstancePtr, u8 Set);
+void XHdcp22Tx_SetContentStreamType(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_ContentStreamType StreamType);
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* End of protection macro */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx_crypt.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx_crypt.c
@@ -0,0 +1,918 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_tx_crypt.c
+* @{
+* @details
+*
+* This is the file for Xilinx HDCP 2.2 transmitter cryptographic functionality.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- -------------------------------------------------------
+* 1.00  JO     10/06/15 Initial release.
+* 1.01  MH     01/15/16 Replaced mallocs with fixed size arrays.
+* 2.00  MH     06/28/16 Updated for repeater downstream support.
+* 2.30  MH     05/16/16 1. Reduced BD_MAX_MOD_SIZE to optimize stack size.
+*                       2. Updated for 64 bit support.
+* 2.40  MH     01/30/18 Added function XHdcp22Tx_RsaSignatureVerify.
+*                       Signature verification has been updated to
+*                       check entire encoded message EM including
+*                       padding PS.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_tx_i.h"
+#include "xhdcp22_common.h"
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/** Size RSA encryption parameters to support 384 byte maximum modulus size */
+#define BD_MAX_MOD_SIZE  (384/sizeof(u32))
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+static int XHdcp22Tx_Mgf1(const u8 *Seed, unsigned int Seedlen, u8 *Mask,
+                          unsigned int MaskLen);
+static int XHdcp22Tx_RsaOaepEncrypt(const u8 *KeyPubNPtr, int KeyPubNSize,
+                                    const u8 *KeyPubEPtr, int KeyEPubSize,
+                                    const u8 *Message, const u32 MessageLen,
+                                    const u8 *MaskingSeed, u8 *EncryptedMessage);
+static int XHdcp22Tx_Pkcs1EmeOaepEncode(const u8 *Message, const u32 MessageLen,
+										const u8 *MaskingSeed, u8 *EncodedMessage);
+static int XHdcp22Tx_RsaEncryptMsg(const u8 *KeyPubNPtr, int KeyPubNSize,
+                                   const u8 *KeyPubEPtr, int KeyPubESize,
+                                   const u8 *MsgPtr, int MsgSize,
+                                   u8 *EncryptedMsgPtr);
+static int XHdcp22Tx_RsaSignatureVerify(const u8 *MessagePtr, int MessageSize,
+                                        const u8 *SignaturePtr,
+                                        const u8 *KpubDcpNPtr, int KpubDcpNSize,
+                                        const u8 *KpubDcpEPtr, int KpubDcpESize);
+
+/************************** Variable Definitions *****************************/
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function is the RSA OAEP masking function.
+*
+* @param  Seed is the masking seed to use.
+* @param  Seedlen is the size of the masking seed .
+* @param  Mask is the output mask.
+* @param  MaskLen is size of the mask.
+*
+* @return XST_SUCCESS
+*
+* @note   None.
+*
+******************************************************************************/
+static int XHdcp22Tx_Mgf1(const u8 *Seed, unsigned int Seedlen,
+                          u8 *Mask, unsigned int MaskLen)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(Seed != NULL);
+	Xil_AssertNonvoid(Seedlen > 0);
+	Xil_AssertNonvoid(Mask != NULL);
+	Xil_AssertNonvoid(MaskLen > 0);
+
+	u8  Hash[XHDCP22_TX_SHA256_HASH_SIZE];
+	u8  HashData[XHDCP22_TX_CERT_PUB_KEY_N_SIZE];	// Seedlen+4
+	u32 C;
+	u8  Cbig[4];
+	u8  T[XHDCP22_TX_CERT_PUB_KEY_N_SIZE]; 		// MaskLen + XHDCP22_TX_SHA256_HASH_SIZE
+
+	/* Step 2: Clear T */
+	memset(T, 0x00, sizeof(T));
+
+	/* Step 3: T = T || SHA256(mgfSeed || C) */
+	memcpy(HashData, Seed, Seedlen);
+
+	for(C=0; (C*XHDCP22_TX_SHA256_HASH_SIZE) < MaskLen; C++)
+	{
+		/* Convert counter value to big endian */
+		Cbig[0] = ((C >> 24) & 0xFF);
+		Cbig[1] = ((C >> 16) & 0xFF);
+		Cbig[2] = ((C >> 8) & 0xFF);
+		Cbig[3] = (C & 0xFF);
+
+		/* Constructing Hash Input */
+		memcpy(HashData+Seedlen, &Cbig, 4);
+
+		/* Computing Hash */
+		XHdcp22Cmn_Sha256Hash(HashData, Seedlen+4, Hash);
+
+		/* Appending Hash to T */
+		memcpy(T+C*XHDCP22_TX_SHA256_HASH_SIZE, Hash, XHDCP22_TX_SHA256_HASH_SIZE);
+	}
+
+	/* Step 4: Output leading maskLen octets of T */
+	memcpy(Mask, T, MaskLen);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements EME-OAEP encoding. The label L is the empty
+* string and the underlying hash function is SHA256.
+*
+* Reference: PKCS#1 v2.1, Section 7.1.1, Part 2
+*
+* @param	Message is the octet string to be encoded
+* @param	MessageLen is the length of the octet string to be encoded.
+* @param	MaskingSeed is the random octet string seed of length hLen.
+* @param	EncodedMessage is the 128 byte encoded octet string.
+*
+* @return	XST_SUCCESS or XST_FAILURE.
+*
+* @note		None.
+*****************************************************************************/
+static int XHdcp22Tx_Pkcs1EmeOaepEncode(const u8 *Message, const u32 MessageLen,
+	const u8 *MaskingSeed, u8 *EncodedMessage)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(Message != NULL);
+	Xil_AssertNonvoid(MessageLen > 0);
+	Xil_AssertNonvoid(MaskingSeed != NULL);
+	Xil_AssertNonvoid(EncodedMessage != NULL);
+
+	u8  lHash[XHDCP22_TX_SHA256_HASH_SIZE];
+	u8  seed[XHDCP22_TX_SHA256_HASH_SIZE];
+	u8  dbMask[XHDCP22_TX_CERT_PUB_KEY_N_SIZE-XHDCP22_TX_SHA256_HASH_SIZE-1];
+	u8  DB[XHDCP22_TX_CERT_PUB_KEY_N_SIZE-XHDCP22_TX_SHA256_HASH_SIZE-1];
+	u8  seedMask[XHDCP22_TX_SHA256_HASH_SIZE];
+	u32 Status;
+
+	/* Step 2a: L is the empty string */
+	XHdcp22Cmn_Sha256Hash(NULL,0,lHash);
+
+	/* Step 2b: Generate PS by initializing DB to zeros */
+	memset(DB, 0x00, sizeof(DB));
+
+	/* Step 2c: Generate DB = lHash || PS || 0x01 || M */
+	memcpy(DB, lHash, XHDCP22_TX_SHA256_HASH_SIZE);
+	DB[XHDCP22_TX_CERT_PUB_KEY_N_SIZE-MessageLen-XHDCP22_TX_SHA256_HASH_SIZE-2] = 0x01;
+	memcpy(DB+XHDCP22_TX_CERT_PUB_KEY_N_SIZE-MessageLen-XHDCP22_TX_SHA256_HASH_SIZE-1,
+			Message, MessageLen);
+
+	/* Step 2d: Generate random seed of length hLen
+	 *   The random seed is passed in as an argument to this function.
+	 */
+
+	/* Step 2e: Generate dbMask = MGF1(seed, length(DB)) */
+	Status = XHdcp22Tx_Mgf1(MaskingSeed, XHDCP22_TX_SHA256_HASH_SIZE, dbMask,
+									XHDCP22_TX_CERT_PUB_KEY_N_SIZE-XHDCP22_TX_SHA256_HASH_SIZE-1);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 2f: Generate maskedDB = DB xor dbMask */
+	XHdcp22Tx_MemXor(DB, DB, dbMask, XHDCP22_TX_CERT_PUB_KEY_N_SIZE-XHDCP22_TX_SHA256_HASH_SIZE-1);
+
+	/* Step 2g: Generate seedMask = MGF(maskedDB, length(seed)) */
+	Status = XHdcp22Tx_Mgf1(DB, XHDCP22_TX_CERT_PUB_KEY_N_SIZE-XHDCP22_TX_SHA256_HASH_SIZE-1,
+									seedMask, XHDCP22_TX_SHA256_HASH_SIZE);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 2h: Generate maskedSeed = seed xor seedMask */
+	XHdcp22Tx_MemXor(seed, MaskingSeed, seedMask, XHDCP22_TX_SHA256_HASH_SIZE);
+
+	/* Step 2i: Form encoded message EM = 0x00 || maskedSeed || maskedDB */
+	memset(EncodedMessage, 0x00, XHDCP22_TX_CERT_PUB_KEY_N_SIZE);
+	memcpy(EncodedMessage+1, seed, XHDCP22_TX_SHA256_HASH_SIZE);
+	memcpy(EncodedMessage+1+XHDCP22_TX_SHA256_HASH_SIZE, DB,
+			XHDCP22_TX_CERT_PUB_KEY_N_SIZE-XHDCP22_TX_SHA256_HASH_SIZE-1);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* RSA verification primitive recovers the message representative from
+* the signature representative under the control of a public key.
+* This is the same as encryption, but it in a totally different context.
+*
+* @param  KeyPubNPtr is the RSA public key modulus part.
+* @param  KeyPubNSize is size of the RSA public key modulus in bytes.
+* @param  KeyPubEPtr is the RSA public key E (exponential) part.
+* @param  KeyEPubSize is the sizeof the RSA public key E (exponential) part in
+*         bytes.
+* @param  MsgPtr is the data to verify (for example a cryptographic signature).
+* @param  MsgSize is the size of the data to verify.
+* @param  EncodedMsgPtr is the resulting data for verification.
+*
+* @return
+*         - XST_SUCCESS if encryption succeeds.
+*         - XST_FAILURE if the message buffer size != key size.
+*
+* @note		Note: Verification with a public key is the same as RSA encoding.
+*
+******************************************************************************/
+static int XHdcp22Tx_RsaEncryptMsg(const u8 *KeyPubNPtr, int KeyPubNSize,
+								   const u8 *KeyPubEPtr, int KeyPubESize,
+								   const u8 *MsgPtr, int MsgSize, u8 *EncryptedMsgPtr)
+{
+	u32 n[BD_MAX_MOD_SIZE], e[BD_MAX_MOD_SIZE],
+	        m[BD_MAX_MOD_SIZE], s[BD_MAX_MOD_SIZE];
+	unsigned int ModSize = KeyPubNSize / sizeof(u32);
+
+
+	/* Check if the length of the data is not equal to the key length. */
+	if(MsgSize != KeyPubNSize) {
+		return XST_FAILURE;
+	}
+
+	mpConvFromOctets(n, ModSize, KeyPubNPtr, KeyPubNSize);
+	mpConvFromOctets(e, ModSize, KeyPubEPtr, KeyPubESize);
+
+	mpConvFromOctets(m, ModSize, MsgPtr, MsgSize);
+	mpModExp(s, m, e, n, ModSize);
+	mpConvToOctets(s, ModSize, EncryptedMsgPtr, MsgSize);
+
+	return XST_SUCCESS;
+}
+
+/****************************************************************************/
+/**
+* This function implements the RSAES-OAEP-Encrypt operation. The message
+* is encoded using EME-OAEP and then encrypted with the public key
+* using RSAEP.
+*
+* Reference: PKCS#1 v2.1, Section 7.1.1
+*
+* @param  KeyPubNPtr is the public certicate modulus.
+* @param  KeyPubNSize is the size public certicate modulus.
+* @param  KeyPubEPtr is the public certicate exponent.
+* @param  KeyEPubSizeis the public certicate exponent size.
+* @param  Message is the octet string to be encrypted.
+* @param  MessageLen is the length of octet string to be encrypted and
+*         must be less than or equal to (nLen - 2*hLen - 2)
+* @param  MaskingSeed is the random octet string seed of length hLen
+*         used by EME-OAEP encoding function.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*****************************************************************************/
+static int XHdcp22Tx_RsaOaepEncrypt(const u8 *KeyPubNPtr, int KeyPubNSize,
+                                    const u8 *KeyPubEPtr, int KeyEPubSize,
+                                    const u8 *Message, const u32 MessageLen,
+                                    const u8 *MaskingSeed, u8 *EncryptedMessage)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(Message != NULL);
+	Xil_AssertNonvoid(MessageLen > 0);
+	Xil_AssertNonvoid(MaskingSeed != NULL);
+	Xil_AssertNonvoid(EncryptedMessage != NULL);
+
+	u8 em[XHDCP22_TX_CERT_PUB_KEY_N_SIZE];
+	int Status;
+
+	/* Step 1: Length checking */
+	if(MessageLen > (XHDCP22_TX_CERT_PUB_KEY_N_SIZE - 2*XHDCP22_TX_SHA256_HASH_SIZE - 2))
+	{
+		return XST_FAILURE;
+	}
+
+	/* Step 2: EME-OAEP Encoding */
+	Status = XHdcp22Tx_Pkcs1EmeOaepEncode(Message, MessageLen, MaskingSeed, em);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Step 3: RSA encryption */
+	Status = XHdcp22Tx_RsaEncryptMsg(KeyPubNPtr, KeyPubNSize, KeyPubEPtr,
+	                                 KeyEPubSize, em, KeyPubNSize,
+	                                 EncryptedMessage);
+	if(Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	return XST_SUCCESS;
+}
+
+
+/****************************************************************************/
+/**
+* This function implements RSASSA-PKCS1-v1_5-Verify for signature
+* verification. The encoding scheme used to generate EM is EMSA-PKCS1-v1_5.
+* The signature size is assumed to be 3072 bits. The underlying hash function
+* is SHA256.
+*
+* Reference: PKCS#1 v2.1, Section 8.2.2 and Section 9.2
+*
+* @param  MessagePtr is a pointer to the start of the message to be hashed.
+* @param  MessageSize is the size of the message to be hashed.
+* @param  SignaturePtr is a pointer to the start of the DCP generated signature.
+* @param  KpubDcpNPtr is a pointer to the N-value of the certificate signature.
+* @param  KpubDcpNSize is the size of the N-value of the certificates signature.
+* @param  KpubDcpEPtr iis a pointer to the E-value of the certificate signature.
+* @param  KpubDcpESize is the size of the E-value of the certificates signature.
+*
+* @return
+*         - XST_SUCCESS if the certificate is valid.
+*         - XST_FAILURE if the certificate is invalid.
+* @note   None.
+*
+*****************************************************************************/
+static int XHdcp22Tx_RsaSignatureVerify(const u8 *MessagePtr, int MessageSize,
+                                        const u8 *SignaturePtr,
+                                        const u8 *KpubDcpNPtr, int KpubDcpNSize,
+                                        const u8 *KpubDcpEPtr, int KpubDcpESize)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(MessagePtr   != NULL);
+	Xil_AssertNonvoid(SignaturePtr != NULL);
+	Xil_AssertNonvoid(KpubDcpNPtr  != NULL);
+	Xil_AssertNonvoid(KpubDcpEPtr  != NULL);
+	Xil_AssertNonvoid(KpubDcpNSize > 0);
+	Xil_AssertNonvoid(KpubDcpESize > 0);
+
+	int i;
+	int Result = XST_SUCCESS;
+	u8 THash[XHDCP22_TX_SHA256_HASH_SIZE];
+	u8 TIdentifer[] = {	0x30, 0x31, 0x30, 0x0d, 0x06, 0x09, 0x60, 0x86,
+					0x48, 0x01, 0x65, 0x03, 0x04, 0x02, 0x01, 0x05,
+					0x00, 0x04, 0x20};
+	u8 Em[XHDCP22_TX_CERT_SIGNATURE_SIZE];
+	u8* EmPtr = NULL;
+
+	/* Create hash of first part of the certificate (without the signature). */
+	XHdcp22Cmn_Sha256Hash(MessagePtr, MessageSize, THash);
+
+	/* Perform RSA decryption and recover EM */
+	Result = XHdcp22Tx_RsaEncryptMsg(KpubDcpNPtr, KpubDcpNSize,
+                                   KpubDcpEPtr, KpubDcpESize,
+                                   SignaturePtr,
+                                   XHDCP22_TX_CERT_SIGNATURE_SIZE,
+                                   Em);
+	if (Result != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/*
+	 * Compare EM to EM'
+	 * where EM = 0x00 || 0x01 || PS || 0x00 || T
+	 * with size 384 bytes
+	 *
+	 * Do the following checks:
+	 *   Check 1: padding start delimiter (2   bytes)
+	 *   Check 2: padding sequence        (330 bytes)
+	 *   Check 3: padding end delimiter   (1   bytes)
+	 *   Check 4: ASN.1 encoding of hash  (51  bytes)
+	 */
+
+	/* Check 1 */
+	if ((Em[0] != 0x00) || (Em[1] != 0x01))
+		return XST_FAILURE;
+
+	/* Check 2 */
+	EmPtr = &Em[2];
+	for (i=0; i<330; i++) {
+		if (EmPtr[i] != 0xFF)
+			return XST_FAILURE;
+	}
+
+	/* Check 3 */
+	EmPtr = &Em[332];
+	if (EmPtr[0] != 0x00)
+		return XST_FAILURE;
+
+	/* Check 4 */
+	EmPtr = &Em[333];
+	if (memcmp(TIdentifer, EmPtr, 19) != 0)
+		return XST_FAILURE;
+	EmPtr = &Em[352];
+	if (memcmp(THash, EmPtr, 32) != 0)
+		return XST_FAILURE;
+
+	return Result;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function generates random octets.
+* Otherwise it uses offloading from hardware.
+*
+* @param  NumOctets is the number of octets in the random number.
+* @param  RandomNumberPtr is a pointer to the random number.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_GenerateRandom(XHdcp22_Tx *InstancePtr, int NumOctets,
+                              u8* RandomNumberPtr)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* Use hardware generator */
+	XHdcp22Rng_GetRandom(&InstancePtr->Rng, RandomNumberPtr, NumOctets, NumOctets);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function verifies the HDCP receivers certificate.
+*
+* @param  CertificatePtr is a pointer to the certificate from the HDCP2.2
+*         receiver.
+* @param  KpubDcpNPtr is a pointer to the N-value of the certificate signature.
+* @param  KpubDcpNSize is the size of the N-value of the certificates signature.
+* @param  KpubDcpEPtr iis a pointer to the E-value of the certificate signature.
+* @param  KpubDcpESize is the size of the E-value of the certificates signature.
+*
+* @return
+*         - XST_SUCCESS if the certificate is valid.
+*         - XST_FAILURE if the certificate is invalid.
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_VerifyCertificate(const XHdcp22_Tx_CertRx* CertificatePtr,
+                                const u8* KpubDcpNPtr, int KpubDcpNSize,
+                                const u8* KpubDcpEPtr, int KpubDcpESize)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(CertificatePtr != NULL);
+	Xil_AssertNonvoid(KpubDcpNPtr != NULL);
+	Xil_AssertNonvoid(KpubDcpEPtr != NULL);
+	Xil_AssertNonvoid(KpubDcpNSize > 0);
+	Xil_AssertNonvoid(KpubDcpESize > 0);
+
+	int Result = XST_SUCCESS;
+
+	Result = XHdcp22Tx_RsaSignatureVerify (
+				(u8 *)CertificatePtr,
+                    (sizeof(XHdcp22_Tx_CertRx) - sizeof(CertificatePtr->Signature)),
+				CertificatePtr->Signature,
+				KpubDcpNPtr, KpubDcpNSize,
+				KpubDcpEPtr, KpubDcpESize);
+
+	return Result;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function verifies a HDCP2 system renewability message (SRM) block.
+*
+* @param  SrmPtr is a pointer to the SRM.
+* @param  SrmSize is the size of the SRM in bytes.
+* @param  KpubDcpNPtr is a pointer to the N-value of the DCP LLC key.
+* @param  KpubDcpNSize is the size of the N-value of the DCP LLC key.
+* @param  KpubDcpEPtr iis a pointer to the E-value of the DCP LLC key.
+* @param  KpubDcpESize is the size of the E-value of the DCP LLC key.
+*
+* @return
+*         - XST_SUCCESS if the SRM block is valid.
+*         - XST_FAILURE if the SRM block is invalid.
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_VerifySRM(const u8* SrmPtr, int SrmSize,
+	const u8* KpubDcpNPtr, int KpubDcpNSize,
+	const u8* KpubDcpEPtr, int KpubDcpESize)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(SrmPtr != NULL);
+	Xil_AssertNonvoid(KpubDcpNPtr != NULL);
+	Xil_AssertNonvoid(KpubDcpEPtr != NULL);
+	Xil_AssertNonvoid(SrmSize > 0);
+	Xil_AssertNonvoid(KpubDcpNSize > 0);
+	Xil_AssertNonvoid(KpubDcpESize > 0);
+
+	int Result = XST_SUCCESS;
+
+	Result = XHdcp22Tx_RsaSignatureVerify (
+				(u8 *)SrmPtr,
+                    SrmSize - XHDCP22_TX_SRM_SIGNATURE_SIZE,
+				SrmPtr + (SrmSize - XHDCP22_TX_SRM_SIGNATURE_SIZE),
+				KpubDcpNPtr, KpubDcpNSize,
+				KpubDcpEPtr, KpubDcpESize);
+
+	return Result;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function computes HPrime
+*
+* @param  Rrx is the Rx random generated value on start of authentication.
+* @param  RxCaps are the capabilities of the receiver.
+* @param  Rtx is the Tx random generated value start of authentication.
+* @param  TxCaps are the capabilities of the receiver.
+* @param  Km is the master key generated by tx.
+* @param  HPrime is a pointer to the HPrime hash from the HDCP2.2 receiver.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_ComputeHPrime(const u8* Rrx, const u8 *RxCaps,
+                             const u8* Rtx, const u8 *TxCaps,
+                             const u8 *Km, u8 *HPrime)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(RxCaps != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(TxCaps != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(HPrime != NULL);
+
+	u8 Aes_Iv[XHDCP22_TX_AES128_SIZE];
+	u8 Aes_Key[XHDCP22_TX_AES128_SIZE];
+	u8 Kd[2 * XHDCP22_TX_AES128_SIZE]; /* Dkey0 || Dkey 1. */
+
+	u8 HashInput[XHDCP22_TX_RTX_SIZE + XHDCP22_TX_RXCAPS_SIZE +
+               XHDCP22_TX_TXCAPS_SIZE];
+	int Idx = 0;
+
+	/* Normally we should do: Key XOR with Rn, but Rn is 0. */
+	memcpy(Aes_Key, Km, XHDCP22_TX_KM_SIZE);
+
+	/* Determine dkey0. */
+	/* Add m = Rtx || Rrx. */
+	memcpy(Aes_Iv, Rtx, XHDCP22_TX_RTX_SIZE);
+	/* Normally we should do Rrx XOR with Ctr0, but Ctr0 is 0. */
+	memcpy(&Aes_Iv[XHDCP22_TX_RTX_SIZE], Rrx, XHDCP22_TX_RRX_SIZE);
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, Kd);
+
+
+	/* Determine dkey1, counter is 1: Rrx | 0x01. */
+	Aes_Iv[15] ^= 0x01; /* big endian! */
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, &Kd[XHDCP22_TX_KM_SIZE]);
+
+
+	/* Create hash with HMAC-SHA256. */
+	/* Input: Rtx || RxCaps || TxCaps. */
+	memcpy(HashInput, Rtx, XHDCP22_TX_RTX_SIZE);
+	Idx += XHDCP22_TX_RTX_SIZE;
+	memcpy(&HashInput[Idx], RxCaps, XHDCP22_TX_RXCAPS_SIZE);
+	Idx += XHDCP22_TX_RXCAPS_SIZE;
+	memcpy(&HashInput[Idx], TxCaps, XHDCP22_TX_TXCAPS_SIZE);
+
+	/* HashKey:	Kd*/
+	XHdcp22Cmn_HmacSha256Hash(HashInput, sizeof(HashInput), Kd,
+                           sizeof(Kd), HPrime);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function computes EdkeyKs. Kd is calculated as in
+* #XHdcp22Tx_ComputeHPrime, but could also be stored the first time.
+* This could save some computing time.
+* According protocol however, only Rrx and Rtx are supposed to be stored.
+*
+* @param  Rn is a pseudo-random nonce.
+* @param  Km is the master key generated by tx..
+*         See also #XHdcp22Tx_ComputeHPrime
+* @param  Ks is the session key.
+* @param  Rrx is the random value generated by rx.
+* @param  Rtx is the random value generated by tx.
+* @param  EdkeyKs is the encrypted Ks output.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+void XHdcp22Tx_ComputeEdkeyKs(const u8* Rn, const u8* Km,
+                              const u8 *Ks,
+                              const u8 *Rrx, const u8 *Rtx,
+                              u8 *EdkeyKs)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(Rn != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(Ks != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(EdkeyKs != NULL);
+
+	u8 Aes_Iv[XHDCP22_TX_AES128_SIZE];
+	u8 Aes_Key[XHDCP22_TX_AES128_SIZE];
+	u8 Dkey2[XHDCP22_TX_AES128_SIZE]; /* Dkey2. */
+
+	/* Key XOR with Rn. */
+	/* Copy Rn to least significant 64-bits. */
+	memset(Aes_Key, 0x0, XHDCP22_TX_KM_SIZE);
+	memcpy(&Aes_Key[XHDCP22_TX_RN_SIZE], Rn, XHDCP22_TX_RN_SIZE);
+	XHdcp22Tx_MemXor(Aes_Key, Aes_Key, Km, XHDCP22_TX_KM_SIZE);
+
+	/* Determine dkey2. */
+	/* Add m = Rtx || Rrx. */
+	memcpy(Aes_Iv, Rtx, XHDCP22_TX_RTX_SIZE);
+	memcpy(&Aes_Iv[XHDCP22_TX_RTX_SIZE], Rrx, XHDCP22_TX_RRX_SIZE);
+	Aes_Iv[15] ^= 0x02; /* big endian! */
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, Dkey2);
+
+
+	/* EdkeyKs = Ks XOR (Dkey2 XOR Rrx). */
+	/* Rrx XOR Dkey2. */
+	memset(EdkeyKs, 0x00, XHDCP22_TX_EDKEY_KS_SIZE);
+	/* Copy Rrx to the least significant 64 bits. */
+	memcpy(&EdkeyKs[XHDCP22_TX_EDKEY_KS_SIZE - XHDCP22_TX_RRX_SIZE], Rrx,
+					XHDCP22_TX_RRX_SIZE);
+	XHdcp22Tx_MemXor(EdkeyKs, EdkeyKs, Dkey2, XHDCP22_TX_AES128_SIZE);
+	/* XOR with Ks. */
+	XHdcp22Tx_MemXor(EdkeyKs, EdkeyKs, Ks, XHDCP22_TX_KS_SIZE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function computes LPrime. Kd is calculated as in
+* #XHdcp22Tx_ComputeHPrime, but could also be stored the first time.
+* This could save some computing time.
+* According protocol however, only Rrx and Rtx are supposed to be stored.
+*
+* @param  Rn is a pseudo-random nonce.
+* @param  Km is the master key generated by tx and previouslyd stored.
+* @param  Rrx is the random value generated by rx.
+* @param  Rtx is the random value generated by tx.
+* @param  LPrime is a pointer to the computed LPrime hash.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+void XHdcp22Tx_ComputeLPrime(const u8* Rn, const u8 *Km,
+                             const u8 *Rrx, const u8 *Rtx,
+                             u8 *LPrime)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(Rn != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(LPrime != NULL);
+
+	u8 Aes_Iv[XHDCP22_TX_AES128_SIZE];
+	u8 Aes_Key[XHDCP22_TX_AES128_SIZE];
+	u8 Kd[2 * XHDCP22_TX_AES128_SIZE]; /* Dkey0 || Dkey 1. */
+	u8 HashKey[XHDCP22_TX_SHA256_HASH_SIZE];
+
+	/* For key derivation, use Km XOR Rn as AES key where Rn=0 during AKE.
+	 * Note: Protocol says we should use incoming Rn and XOR it with Km,
+	 * but then the output does not match the errata output.
+	 * For now we use for Rn 0, which matches the test vectors.
+	 */
+	memcpy(Aes_Key, Km, XHDCP22_TX_KM_SIZE);
+
+	/* Compute Dkey0. */
+	/* Add m = Rtx || Rrx. */
+	memcpy(Aes_Iv, Rtx, XHDCP22_TX_RTX_SIZE);
+	/* Rrx XOR Ctr0, where Ctr0 is 0. */
+	memcpy(&Aes_Iv[XHDCP22_TX_RTX_SIZE], Rrx, XHDCP22_TX_RRX_SIZE);
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, Kd);
+
+
+	/* Compute Dkey0 , counter is 1: Rrx | 0x01. */
+	Aes_Iv[15] ^= 0x01; /* big endian! */
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, &Kd[XHDCP22_TX_KM_SIZE]);
+
+
+	/* Create hash with HMAC-SHA256. */
+	/* Input: Rn. */
+	/* Key:	Kd XOR Rrx (least sign. 64 bits). */
+	memset(HashKey, 0x00, XHDCP22_TX_SHA256_HASH_SIZE);
+	memcpy(&HashKey[XHDCP22_TX_SHA256_HASH_SIZE-XHDCP22_TX_RRX_SIZE], Rrx,
+         XHDCP22_TX_RRX_SIZE);
+	XHdcp22Tx_MemXor(HashKey, HashKey, Kd, XHDCP22_TX_SHA256_HASH_SIZE);
+	XHdcp22Cmn_HmacSha256Hash(Rn, XHDCP22_TX_RN_SIZE, HashKey,
+                           XHDCP22_TX_SHA256_HASH_SIZE, LPrime);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function computes V
+*
+* @param
+* @param  V is a pointer to the computed V hash.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_ComputeV(const u8* Rn, const u8* Rrx, const u8* RxInfo,
+	const u8* Rtx, const u8* RecvIDList, const u8 RecvIDCount,
+	const u8* SeqNum_V, const u8* Km, u8* V)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(Rn != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(RxInfo != NULL);
+	Xil_AssertVoid(SeqNum_V != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(V != NULL);
+
+	u8 Aes_Iv[XHDCP22_TX_AES128_SIZE];
+	u8 Aes_Key[XHDCP22_TX_AES128_SIZE];
+	u8 Kd[2 * XHDCP22_TX_AES128_SIZE]; /* Dkey0 || Dkey 1. */
+
+	u8 HashInput[(XHDCP22_TX_REPEATER_MAX_DEVICE_COUNT * XHDCP22_TX_RCVID_SIZE) +
+		XHDCP22_TX_RXINFO_SIZE + XHDCP22_TX_SEQ_NUM_V_SIZE];
+	int Idx = 0;
+
+	/* For key derivation, use Km XOR Rn as AES key where Rn=0 during AKE.
+	* Note: Protocol says we should use incoming Rn and XOR it with Km,
+	* but then the output does not match the errata output.
+	* For now we use for Rn 0, which matches the test vectors.
+	*/
+	memcpy(Aes_Key, Km, XHDCP22_TX_KM_SIZE);
+
+	/* Determine dkey0. */
+	/* Add m = Rtx || Rrx. */
+	memcpy(Aes_Iv, Rtx, XHDCP22_TX_RTX_SIZE);
+	/* Normally we should do Rrx XOR with Ctr0, but Ctr0 is 0. */
+	memcpy(&Aes_Iv[XHDCP22_TX_RTX_SIZE], Rrx, XHDCP22_TX_RRX_SIZE);
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, Kd);
+
+	/* Determine dkey1, counter is 1: Rrx | 0x01. */
+	Aes_Iv[15] ^= 0x01; /* big endian! */
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, &Kd[XHDCP22_TX_KM_SIZE]);
+
+	/* Create hash with HMAC-SHA256. */
+	/* Input: ReceiverID list || RxInfo || seq_num_V. */
+	memcpy(HashInput, RecvIDList, (RecvIDCount*XHDCP22_TX_RCVID_SIZE));
+	Idx += (RecvIDCount*XHDCP22_TX_RCVID_SIZE);
+	memcpy(&HashInput[Idx], RxInfo, XHDCP22_TX_RXINFO_SIZE);
+	Idx += XHDCP22_TX_RXINFO_SIZE;
+	memcpy(&HashInput[Idx], SeqNum_V, XHDCP22_TX_SEQ_NUM_V_SIZE);
+	Idx += XHDCP22_TX_SEQ_NUM_V_SIZE;
+	/* HashKey:	Kd*/
+	XHdcp22Cmn_HmacSha256Hash(HashInput, Idx, Kd, sizeof(Kd), V);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function computes M
+*
+* @param
+* @param  M is a pointer to the computed M hash.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_ComputeM(const u8* Rn, const u8* Rrx, const u8* Rtx,
+	const u8* StreamIDType, const u8* k,
+	const u8* SeqNum_M, const u8* Km, u8* M)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(Rn != NULL);
+	Xil_AssertVoid(Rrx != NULL);
+	Xil_AssertVoid(Rtx != NULL);
+	Xil_AssertVoid(StreamIDType != NULL);
+	Xil_AssertVoid(k != NULL);
+	Xil_AssertVoid(SeqNum_M != NULL);
+	Xil_AssertVoid(Km != NULL);
+	Xil_AssertVoid(M != NULL);
+
+	u8 Aes_Iv[XHDCP22_TX_AES128_SIZE];
+	u8 Aes_Key[XHDCP22_TX_AES128_SIZE];
+	u8 Kd[2 * XHDCP22_TX_AES128_SIZE]; /* Dkey0 || Dkey 1. */
+
+	u8 SHA256_Kd[XHDCP22_TX_SHA256_HASH_SIZE];
+
+	u16 StreamIDCount;
+
+	/* K value is in big endian format */
+	StreamIDCount  = k[0] << 8; // MSB
+	StreamIDCount |= k[1];      // LSB
+
+	u8 HashInput[(XHDCP22_TX_REPEATER_MAX_DEVICE_COUNT * XHDCP22_TX_RCVID_SIZE) +
+		XHDCP22_TX_RXINFO_SIZE + XHDCP22_TX_SEQ_NUM_M_SIZE];
+	int Idx = 0;
+
+	/* For key derivation, use Km XOR Rn as AES key where Rn=0 during AKE.
+	* Note: Protocol says we should use incoming Rn and XOR it with Km,
+	* but then the output does not match the errata output.
+	* For now we use for Rn 0, which matches the test vectors.
+	*/
+	memcpy(Aes_Key, Km, XHDCP22_TX_KM_SIZE);
+
+	/* Determine dkey0. */
+	/* Add m = Rtx || Rrx. */
+	memcpy(Aes_Iv, Rtx, XHDCP22_TX_RTX_SIZE);
+	/* Normally we should do Rrx XOR with Ctr0, but Ctr0 is 0. */
+	memcpy(&Aes_Iv[XHDCP22_TX_RTX_SIZE], Rrx, XHDCP22_TX_RRX_SIZE);
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, Kd);
+
+	/* Determine dkey1, counter is 1: Rrx | 0x01. */
+	Aes_Iv[15] ^= 0x01; /* big endian! */
+	XHdcp22Cmn_Aes128Encrypt(Aes_Iv, Aes_Key, &Kd[XHDCP22_TX_KM_SIZE]);
+
+	/* Create hash with SHA256 */
+	XHdcp22Cmn_Sha256Hash(Kd, sizeof(Kd), SHA256_Kd);
+
+	/* Create hash with HMAC-SHA256. */
+	/* Input: StreamID_Type list || seq_num_M. */
+	memcpy(HashInput, StreamIDType, (StreamIDCount*XHDCP22_TX_STREAMID_TYPE_SIZE));
+	Idx += (StreamIDCount*XHDCP22_TX_STREAMID_TYPE_SIZE);
+	memcpy(&HashInput[Idx], SeqNum_M, XHDCP22_TX_SEQ_NUM_M_SIZE);
+	Idx += XHDCP22_TX_SEQ_NUM_M_SIZE;
+	/* HashKey:	SHA256(Kd) */
+	XHdcp22Cmn_HmacSha256Hash(HashInput, Idx, SHA256_Kd, sizeof(SHA256_Kd), M);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function encrypts the Km value with the receivers public key into Ekh(Km)
+*
+* @param  CertificatePtr is a pointer to the certificate from the HDCP2.2 receiver.
+* @param  KmPtr is the random master key.
+* @param  MaskingSeedPtr is a pointer to a 32 byte seed for masking in the MGF1 function
+*         used in RSA-OEAP encryption.
+* @param  EncryptedKmPtr output of the encryption with a 128 byte (1024 bit) size.
+*
+* @return
+*         - XST_SUCCESS if encryption succeeded.
+*         - XST_FAILURE if encryption failed.
+*
+* @note   None.
+*
+******************************************************************************/
+int XHdcp22Tx_EncryptKm(const XHdcp22_Tx_CertRx* CertificatePtr,
+                        const u8* KmPtr, u8 *MaskingSeedPtr, u8* EncryptedKmPtr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(CertificatePtr != NULL);
+	Xil_AssertNonvoid(KmPtr != NULL);
+	Xil_AssertNonvoid(MaskingSeedPtr != NULL);
+	Xil_AssertNonvoid(EncryptedKmPtr != NULL);
+
+	return XHdcp22Tx_RsaOaepEncrypt(CertificatePtr->N, 	XHDCP22_TX_CERT_PUB_KEY_N_SIZE,
+                                  CertificatePtr->e, XHDCP22_TX_CERT_PUB_KEY_E_SIZE,
+                                  KmPtr, XHDCP22_TX_KM_SIZE,
+                                  MaskingSeedPtr, EncryptedKmPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function calculates a XOR on a array.
+*
+* @param  Output is the XOR of the input arrays.
+* @param  InputA is a input array.
+* @param  InputB is a input array.
+* @param  Size is the size of the buffers to XOR.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XHdcp22Tx_MemXor(u8 *Output, const u8 *InputA, const u8 *InputB,
+                      unsigned int Size)
+{
+	/* Verify arguments */
+	Xil_AssertVoid(Output != NULL);
+	Xil_AssertVoid(InputA != NULL);
+	Xil_AssertVoid(InputB != NULL);
+
+	unsigned int i=0;
+	for (i=0; i<Size; i++) {
+		Output[i] = InputA[i] ^ InputB[i];
+	}
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx_i.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx_i.h
@@ -0,0 +1,536 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_tx_i.h
+* @{
+* @details
+*
+* This file contains data which is shared between files and internal to the
+* XIntc component. It is intended for internal use only.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     06/24/15 Initial release.
+* 1.01  MH     03/14/15 Changed maximum locality check count
+*                       from 1024 to 128.
+* 2.00  MH     06/28/16 Updated for repeater downstream support.
+* 2.01  MH     02/13/17 1. Updated maximum locality check count
+*                       from 128 to 8 to avoid delays in re-auth.
+*                       2. Added log events for failures.
+* </pre>
+*
+******************************************************************************/
+#ifndef XHDCP22_TX_I_H
+/** prevent circular inclusions by using protection macros. */
+#define XHDCP22_TX_I_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xhdcp22_tx.h"
+
+/************************** Constant Definitions *****************************/
+/** Maximum allowed re-checking locality, prescribed by LLC. */
+#define XHDCP22_TX_MAX_ALLOWED_LOCALITY_CHECKS  8
+/** Maximum allowed re-checking content stream management */
+#define XHDCP22_TX_MAX_ALLOWED_STREAM_MANAGE_CHECKS 128
+
+#define XHDCP22_TX_LC128_SIZE                   16  /**< Lc128 global constant size */
+
+#define XHDCP22_TX_RCVID_SIZE                   5   /**< Unique receiver Id size in bytes */
+
+#define XHDCP22_TX_REPEATER_MAX_DEVICE_COUNT    31  /**< Max number of downstream devices allowed */
+#define XHDCP22_TX_REPEATER_MAX_CASCADE_DEPTH   4   /**< Max cascade depth */
+
+/* Message Ids. */
+#define XHDCP22_TX_MSG_UNDEFINED                0   /**< Undefined. */
+#define XHDCP22_TX_AKE_INIT                     2   /**< AKE Init message. */
+#define XHDCP22_TX_AKE_INIT_SIZE                12  /**< AKE Init message size. */
+#define XHDCP22_TX_AKE_SEND_CERT                3   /**< AKE Send Certificate message. */
+#define XHDCP22_TX_AKE_SEND_CERT_SIZE           534 /**< AKE Send Certificate message size. */
+#define XHDCP22_TX_AKE_NO_STORED_KM             4   /**< AKE No Stored Km message. */
+#define XHDCP22_TX_AKE_NO_STORED_KM_SIZE        129 /**< AKE No Stored Km message size. */
+#define XHDCP22_TX_AKE_STORED_KM                5   /**< AKE Stored Km message size. */
+#define XHDCP22_TX_AKE_STORED_KM_SIZE           33  /**< AKE Stored Km message size. */
+#define XHDCP22_TX_AKE_SEND_H_PRIME             7   /**< AKE H' message. */
+#define XHDCP22_TX_AKE_SEND_H_PRIME_SIZE        33  /**< AKE H' message size. */
+#define XHDCP22_TX_AKE_SEND_PAIRING_INFO        8   /**< AKE Pairing info message.*/
+#define XHDCP22_TX_AKE_SEND_PAIRING_INFO_SIZE   17  /**< AKE Pairing info message size. */
+#define XHDCP22_TX_LC_INIT                      9   /**< LC Init message. */
+#define XHDCP22_TX_LC_INIT_SIZE                 9   /**< LC Init message size. */
+#define XHDCP22_TX_LC_SEND_L_PRIME              10  /**< Send L' message. */
+#define XHDCP22_TX_LC_SEND_L_PRIME_SIZE         33  /**< Send L' message size. */
+#define XHDCP22_TX_SKE_SEND_EKS                 11  /**< Send Eks message. */
+#define XHDCP22_TX_SKE_SEND_EKS_SIZE            25  /**< Send Eks message size.*/
+#define XHDCP22_TX_REPEATAUTH_SEND_RECVID_LIST  12  /**< Repeater Auth send receiver ID list message. */
+#define XHDCP22_TX_REPEATAUTH_SEND_RECVID_LIST_SIZE 177 /**< Repeater Auth send receiver ID list maximum message size. */
+#define XHDCP22_TX_REPEATAUTH_SEND_ACK          15  /**< RepeaterAuth send ack message. */
+#define XHDCP22_TX_REPEATAUTH_SEND_ACK_SIZE     17  /**< RepeaterAuth send ack message size in bytes. */
+#define XHDCP22_TX_REPEATAUTH_STREAM_MANAGE     16  /**< RepeaterAuth stream manage message. */
+#define XHDCP22_TX_REPEATAUTH_STREAM_MANAGE_SIZE 8  /**< RepeaterAuth stream manage message size in bytes. */
+#define XHDCP22_TX_REPEATAUTH_STREAM_READY      17  /**< RepeaterAuth stream ready message. */
+#define XHDCP22_TX_REPEATAUTH_STREAM_READY_SIZE 33  /**< RepeaterAuth stream ready message size in bytes. */
+
+/** Reason why the timer was started: Undefined. */
+#define XHDCP22_TX_TS_UNDEFINED                 XHDCP22_TX_MSG_UNDEFINED
+
+/** Reason why the timer was started:
+* Waiting for Content Stream Type to be set when in repeater mode.
+* @note: The message ids also double as a reason identifier.
+*        Thus, the value of this define should NOT overlap a message Id.*/
+#define XHDCP22_TX_TS_WAIT_FOR_STREAM_TYPE      0xFD
+/** Reason why the timer was started:
+* Mandatory wait of 200 ms before the cipher may be activated.
+* Authenticated flag is only set after this period has expired.
+* @note: The message ids also double as a reason identifier.
+*        Thus, the value of this define should NOT overlap a message Id.*/
+#define XHDCP22_TX_TS_WAIT_FOR_CIPHER           0xFE
+/** Reason why the timer was started: Status checking.
+* @note: The message ids also double as a reason identifier.
+*        Thus, the value of this define should NOT overlap a message Id.*/
+#define XHDCP22_TX_TS_RX_REAUTH_CHECK           0xFF
+
+/** Internal used timer counter for timeout checking. */
+#define XHDCP22_TX_TIMER_CNTR_0                 0
+/** Internal used timer counter for logging. */
+#define XHDCP22_TX_TIMER_CNTR_1                 1
+
+#define XHDCP22_TX_HDCPPORT_VERSION_OFFSET      0x50 /**< DDC version offset. */
+#define XHDCP22_TX_HDCPPORT_WRITE_MSG_OFFSET    0x60 /**< DDC write message buffer offset. */
+#define XHDCP22_TX_HDCPPORT_RXSTATUS_OFFSET     0x70 /**< DDC RX status offset. */
+#define XHDCP22_TX_HDCPPORT_READ_MSG_OFFSET     0x80 /**< DDC read message buffer offset. */
+
+/** HDCP Port DDC Rx status register masks. */
+#define XHDCP22_TX_RXSTATUS_REAUTH_REQ_MASK     (1<<11) /**< RX status REAUTHENTICATION bit. */
+#define XHDCP22_TX_RXSTATUS_READY_MASK          (1<<10) /**< RX status READY bit. */
+#define XHDCP22_TX_RXSTATUS_AVAIL_BYTES_MASK    (0x3FF) /**< RX status available bytes in read message buffer. */
+
+/** RX certificate and Tx public key sizes in bytes. */
+#define XHDCP22_TX_CERT_RCVID_SIZE              5   /**< Unique receiver Id size in the RX certificate. */
+#define XHDCP22_TX_CERT_PUB_KEY_N_SIZE          128 /**< Public key-N size in the RX certificate. */
+#define XHDCP22_TX_CERT_PUB_KEY_E_SIZE          3   /**< Public key-E size in the RX certificate. */
+#define XHDCP22_TX_CERT_RSVD_SIZE               2   /**< Reserved size in the RX certificate. */
+#define XHDCP22_TX_CERT_SIGNATURE_SIZE          384 /**< Signature size in the RX certificate. */
+/** Total size of the RX certificate. */
+#define XHDCP22_TX_CERT_SIZE                     \
+       ( XHDCP22_TX_CERT_RCVID_SIZE +            \
+         XHDCP22_TX_CERT_PUB_KEY_N_SIZE +        \
+         XHDCP22_TX_CERT_PUB_KEY_E_SIZE +        \
+         XHDCP22_TX_CERT_RSVD_SIZE +             \
+         XHDCP22_TX_CERT_SIGNATURE_SIZE )
+#define XHDCP22_TX_RXCAPS_SIZE                  3   /**< RX capabilities size. */
+#define XHDCP22_TX_TXCAPS_SIZE                  3   /**< TX capabilities size. */
+#define XHDCP22_TX_KPUB_DCP_LLC_N_SIZE          384 /**< LLC public key-N size. */
+#define XHDCP22_TX_KPUB_DCP_LLC_E_SIZE          1   /**< LLC public key-E size. */
+
+/* defines for de/encryption. */
+#define XHDCP22_TX_SHA256_HASH_SIZE             32 /**< SHA256 hash size in bytes. */
+#define XHDCP22_TX_AES128_SIZE                  16 /**< AES128 keys in bytes. */
+
+/* Sizes of keys in bytes. */
+#define XHDCP22_TX_RTX_SIZE                     8     /**< 64 bits. */
+#define XHDCP22_TX_RRX_SIZE                     8     /**< 64 bits. */
+#define XHDCP22_TX_KM_SIZE                      XHDCP22_TX_AES128_SIZE
+#define XHDCP22_TX_E_KPUB_KM_SIZE               128   /**< 1024 bits. */
+#define XHDCP22_TX_H_PRIME_SIZE                 32    /**< 256 bits. */
+#define XHDCP22_TX_EKH_KM_SIZE                  16    /**< 128 bits. */
+#define XHDCP22_TX_KM_MSK_SEED_SIZE             XHDCP22_TX_SHA256_HASH_SIZE
+#define XHDCP22_TX_RN_SIZE                      8     /**< 64-bits. */
+#define XHDCP22_TX_RIV_SIZE                     8     /**< 64-bits. */
+#define XHDCP22_TX_L_PRIME_SIZE                 32    /**< 256 bits. */
+#define XHDCP22_TX_KS_SIZE                      16    /**< 128 bits. */
+#define XHDCP22_TX_EDKEY_KS_SIZE                16    /**< 128 bits. */
+
+/* Sizes of SRM Fields in bytes. */
+#define XHDCP22_TX_SRM_RCVID_SIZE       XHDCP22_TX_RCVID_SIZE   /**< Receiver Id size in the SRM block. */
+#define XHDCP22_TX_SRM_SIGNATURE_SIZE   384                     /**< Signature size in the SRM block. */
+
+/* Defines for Repeater Authentication messages */
+#define XHDCP22_TX_RXINFO_SIZE                  2     /**< RxInfo size in bytes. */
+#define XHDCP22_TX_SEQ_NUM_V_SIZE               3     /**< Seq_num_v size in bytes. */
+#define XHDCP22_TX_V_SIZE                       32    /**< V size in bytes. */
+#define XHDCP22_TX_V_PRIME_SIZE                 16    /**< VPrime size in bytes. */
+#define XHDCP22_TX_SEQ_NUM_M_SIZE               3     /**< Seq_num_m size in bytes. */
+#define XHDCP22_TX_K_SIZE                       2     /**< K size in bytes. */
+#define XHDCP22_TX_STREAMID_TYPE_SIZE           2     /**< Stream ID and Type size in bytes. */
+#define XHDCP22_TX_M_PRIME_SIZE                 32    /**< MPrime size in bytes. */
+
+/* Test flags to trigger errors for unit tests. */
+
+/** Use a certificate test vector. */
+#define XHDCP22_TX_TEST_CERT_RX         0x00000001
+/** Use a H_Prime test vector.*/
+#define XHDCP22_TX_TEST_H1              0x00000002
+/** Use a L_Prime test vector.*/
+#define XHDCP22_TX_TEST_L1              0x00000004
+/** Use a pairing info Ekh(Km) test vector, use i.c.w #XHDCP22_TX_TEST_RCV_TIMEOUT*/
+#define XHDCP22_TX_TEST_EKH_KM          0x00000008
+/** Invalidate a value */
+#define XHDCP22_TX_TEST_INVALID_VALUE   0x00000010
+/** Timeout on a received message. */
+#define XHDCP22_TX_TEST_RCV_TIMEOUT     0x00000020
+/** Use a V_Prime test vector. */
+#define XHDCP22_TX_TEST_V1              0x00000040
+/** Use a M_Prime test vector. */
+#define XHDCP22_TX_TEST_M1              0x00000080
+/** AKE is forced using a stored Km scenarion. Pairing info is pre-loaded
+* with test vectors that forces Stored Km scenario.*/
+#define XHDCP22_TX_TEST_STORED_KM       0x00000100
+/** Disable timeout checking. this is mainly used to check the HDCP RX core in
+* loopback mode in case it cannot meet timing requirements (no offloading to
+* hardware) and reponsetimes need to be logged.*/
+#define XHDCP22_TX_TEST_NO_TIMEOUT      0x00000200
+/** Pairing info is cleared, to force a non-stored Km scenario */
+#define XHDCP22_TX_TEST_CLR_PAIRINGINFO 0x00000400
+/** Use testvectors for receiver R1 */
+#define XHDCP22_TX_TEST_USE_TEST_VECTOR_R1 0x80000000
+
+/** DDC base address (0x74 >> 1) */
+#define XHDCP22_TX_DDC_BASE_ADDRESS     0x3A
+
+/**************************** Type Definitions *******************************/
+/**
+* These constants are used to set the core into testing mode with #XHdcp22Tx_TestSetMode.
+*/
+typedef enum {
+	XHDCP22_TX_TESTMODE_DISABLED,       /**< Testmode is disabled. */
+	XHDCP22_TX_TESTMODE_SW_RX,          /**< Actual HDCP2.2 RX component is connected. */
+	XHDCP22_TX_TESTMODE_NO_RX,          /**< HDCP2.2 RX software component is not available and will be emulated. */
+	XHDCP22_TX_TESTMODE_UNIT,           /**< HDCP2.2 RX is emulated, #XHdcp22Tx_LogDisplay shows source code.*/
+	XHDCP22_TX_TESTMODE_USE_TESTKEYS,   /**< Use test keys as defined in Errata to HDCP on HDMI Specification
+	                                         Revision 2.2, February 09, 2015. */
+	XHDCP22_TX_TESTMODE_INVALID         /**< Last value the list, only used for checking. */
+} XHdcp22_Tx_TestMode;
+
+/**
+* Value definitions for debugging.
+* These values are used as parameter for the #XHDCP22_TX_LOG_EVT_DBG
+* logging event.
+*/
+typedef enum
+{
+	XHDCP22_TX_LOG_DBG_STARTIMER,
+	XHDCP22_TX_LOG_DBG_MSGAVAILABLE,
+	XHDCP22_TX_LOG_DBG_TX_AKEINIT,
+	XHDCP22_TX_LOG_DBG_RX_CERT,
+	XHDCP22_TX_LOG_DBG_VERIFY_SIGNATURE,
+	XHDCP22_TX_LOG_DBG_VERIFY_SIGNATURE_PASS,
+	XHDCP22_TX_LOG_DBG_VERIFY_SIGNATURE_FAIL,
+	XHDCP22_TX_LOG_DBG_DEVICE_IS_REVOKED,
+	XHDCP22_TX_LOG_DBG_ENCRYPT_KM,
+	XHDCP22_TX_LOG_DBG_ENCRYPT_KM_DONE,
+	XHDCP22_TX_LOG_DBG_TX_NOSTOREDKM,
+	XHDCP22_TX_LOG_DBG_TX_STOREDKM,
+	XHDCP22_TX_LOG_DBG_RX_H1,
+	XHDCP22_TX_LOG_DBG_RX_EKHKM,
+	XHDCP22_TX_LOG_DBG_COMPUTE_H,
+	XHDCP22_TX_LOG_DBG_COMPUTE_H_DONE,
+	XHDCP22_TX_LOG_DBG_COMPARE_H_FAIL,
+	XHDCP22_TX_LOG_DBG_TX_LCINIT,
+	XHDCP22_TX_LOG_DBG_RX_L1,
+	XHDCP22_TX_LOG_DBG_COMPUTE_L,
+	XHDCP22_TX_LOG_DBG_COMPUTE_L_DONE,
+	XHDCP22_TX_LOG_DBG_COMPARE_L_FAIL,
+	XHDCP22_TX_LOG_DBG_TX_EKS,
+	XHDCP22_TX_LOG_DBG_COMPUTE_EDKEYKS,
+	XHDCP22_TX_LOG_DBG_COMPUTE_EDKEYKS_DONE,
+	XHDCP22_TX_LOG_DBG_RX_RCVIDLIST,
+	XHDCP22_TX_LOG_DBG_COMPUTE_V,
+	XHDCP22_TX_LOG_DBG_COMPUTE_V_DONE,
+	XHDCP22_TX_LOG_DBG_COMPARE_V_FAIL,
+	XHDCP22_TX_LOG_DBG_RX_M1,
+	XHDCP22_TX_LOG_DBG_COMPUTE_M,
+	XHDCP22_TX_LOG_DBG_COMPUTE_M_DONE,
+	XHDCP22_TX_LOG_DBG_CHECK_REAUTH,
+	XHDCP22_TX_LOG_DBG_TIMEOUT,
+	XHDCP22_TX_LOG_DBG_TIMESTAMP,
+	XHDCP22_TX_LOG_DBG_AES128ENC,
+	XHDCP22_TX_LOG_DBG_AES128ENC_DONE,
+	XHDCP22_TX_LOG_DBG_SHA256HASH,
+	XHDCP22_TX_LOG_DBG_SHA256HASH_DONE,
+	XHDCP22_TX_LOG_DBG_OEAPENC,
+	XHDCP22_TX_LOG_DBG_OEAPENC_DONE,
+	XHDCP22_TX_LOG_DBG_RSAENC,
+	XHDCP22_TX_LOG_DBG_RSAENC_DONE,
+	XHDCP22_TX_LOG_DBG_MSG_WRITE_FAIL,
+	XHDCP22_TX_LOG_DBG_MSG_READ_FAIL
+} XHdcp22_Tx_LogDebugValue;
+
+/**
+
+* This typedef contains the public key certificate of Receiver that is received
+* with AKE_Send_Cert.
+*/
+typedef	struct {
+	u8 ReceiverId[XHDCP22_TX_CERT_RCVID_SIZE];
+	u8 N[XHDCP22_TX_CERT_PUB_KEY_N_SIZE];
+	u8 e[XHDCP22_TX_CERT_PUB_KEY_E_SIZE];
+	u8 Reserved[XHDCP22_TX_CERT_RSVD_SIZE];
+	u8 Signature[XHDCP22_TX_CERT_SIGNATURE_SIZE];
+} XHdcp22_Tx_CertRx;
+
+/**
+* This typedef contains the received AKE_Send_Cert message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	XHdcp22_Tx_CertRx CertRx;
+	u8 Rrx[XHDCP22_TX_RRX_SIZE];
+	u8 RxCaps[XHDCP22_TX_RXCAPS_SIZE];
+} XHdcp22_Tx_AKESendCert;
+
+/**
+* This typedef contains the received AKE_Send_H_prime message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 HPrime[XHDCP22_TX_H_PRIME_SIZE];
+} XHdcp22_Tx_AKESendHPrime;
+
+/**
+* This typedef contains the received AKE_Send_Pairing_Info message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 EKhKm[XHDCP22_TX_EKH_KM_SIZE];
+} XHdcp22_Tx_AKESendPairingInfo;
+
+/**
+* This typedef contains the received AKE_Send_L_prime message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 LPrime[XHDCP22_TX_L_PRIME_SIZE];
+} XHdcp22_Tx_LCSendLPrime;
+
+/**
+* This typedef contains the transmitted AKE_Init message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 Rtx[XHDCP22_TX_RTX_SIZE];
+	u8 TxCaps[XHDCP22_TX_TXCAPS_SIZE];
+} XHdcp22_Tx_AKEInit;
+
+/**
+* This typedef contains the transmitted AKE_No_Stored_km message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 EKpubKm[XHDCP22_TX_E_KPUB_KM_SIZE];
+} XHdcp22_Tx_AKENoStoredKm;
+
+
+/**
+* This typedef contains the transmitted AKE_Stored_km message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 EKhKm[XHDCP22_TX_EKH_KM_SIZE];
+	u8 Rtx[XHDCP22_TX_RTX_SIZE];	// In the protocol defined as M=Rtx || Rrx
+	u8 Rrx[XHDCP22_TX_RRX_SIZE];
+} XHdcp22_Tx_AKEStoredKm;
+
+/**
+* This typedef contains the transmitted LC_Init message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 Rn[XHDCP22_TX_RN_SIZE];
+} XHdcp22_Tx_LCInit;
+
+/**
+* This typedef contains the transmitted SKE_Send_Eks message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 EDkeyKs[XHDCP22_TX_EDKEY_KS_SIZE];
+	u8 Riv[XHDCP22_TX_RIV_SIZE];
+} XHdcp22_Tx_SKESendEks;
+
+/**
+* This typedef contains the RepeaterAuth_Send_ReceiverID_List message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 RxInfo[XHDCP22_TX_RXINFO_SIZE];
+	u8 SeqNum_V[XHDCP22_TX_SEQ_NUM_V_SIZE];
+	u8 VPrime[XHDCP22_TX_V_PRIME_SIZE];
+	u8 ReceiverIDs[XHDCP22_TX_REPEATER_MAX_DEVICE_COUNT][XHDCP22_TX_RCVID_SIZE];
+} XHdcp22_Tx_RepeatAuthSendRecvIDList;
+
+/**
+* This typedef contains the RepeaterAuth_Send_Ack message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 V[XHDCP22_TX_V_PRIME_SIZE];
+} XHdcp22_Tx_RepeatAuthSendAck;
+
+/**
+* This typedef contains the RepeaterAuth_Stream_Manage message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 SeqNum_M[XHDCP22_TX_SEQ_NUM_M_SIZE];
+	u8 K[XHDCP22_TX_K_SIZE];
+	u8 StreamID_Type[XHDCP22_TX_STREAMID_TYPE_SIZE];
+} XHdcp22_Tx_RepeatAuthStreamManage;
+
+/**
+* This typedef contains the RepeaterAuth_Stream_Ready message definition.
+*/
+typedef struct
+{
+	u8 MsgId;
+
+	u8 MPrime[XHDCP22_TX_M_PRIME_SIZE];
+} XHdcp22_Tx_RepeatAuthStreamReady;
+
+/**
+* Message buffer structure.
+*/
+typedef union
+{
+	/* Message Id. */
+	u8 MsgId;
+
+	/* Received messages. */
+	XHdcp22_Tx_AKESendCert        AKESendCert;
+	XHdcp22_Tx_AKESendHPrime      AKESendHPrime;
+	XHdcp22_Tx_AKESendPairingInfo AKESendPairingInfo;
+	XHdcp22_Tx_LCSendLPrime       LCSendLPrime;
+	XHdcp22_Tx_RepeatAuthSendRecvIDList RepeatAuthSendRecvIDList;
+	XHdcp22_Tx_RepeatAuthStreamReady RepeatAuthStreamReady;
+
+	/* Transmitted messages. */
+	XHdcp22_Tx_AKEInit            AKEInit;
+	XHdcp22_Tx_AKENoStoredKm      AKENoStoredKm;
+	XHdcp22_Tx_AKEStoredKm        AKEStoredKm;
+	XHdcp22_Tx_LCInit             LCInit;
+	XHdcp22_Tx_SKESendEks         SKESendEks;
+	XHdcp22_Tx_RepeatAuthSendAck  RepeatAuthSendAck;
+	XHdcp22_Tx_RepeatAuthStreamManage RepeatAuthStreamManage;
+} XHdcp22_Tx_Message;
+
+/**
+* Message including the DDC Address.
+*/
+typedef struct
+{
+	u8 DdcAddress;
+	XHdcp22_Tx_Message Message;
+} XHdcp22_Tx_DDCMessage;
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Prototypes ******************************/
+
+/* Crypto functions */
+void XHdcp22Tx_MemXor(u8 *Output, const u8 *InputA, const u8 *InputB,
+                      unsigned int Size);
+int XHdcp22Tx_VerifyCertificate(const XHdcp22_Tx_CertRx *CertificatePtr,
+                                const u8* KpubDcpNPtr, int KpubDcpNSize,
+                                const u8* KpubDcpEPtr, int KpubDcpESize);
+int XHdcp22Tx_VerifySRM(const u8* SrmPtr, int SrmSize,
+                        const u8* KpubDcpNPtr, int KpubDcpNSize,
+                        const u8* KpubDcpEPtr, int KpubDcpESize);
+void XHdcp22Tx_ComputeHPrime(const u8 *Rrx, const u8 *RxCaps,
+                             const u8* Rtx,  const u8 *TxCaps,
+                             const u8 *Km, u8 *HPrime);
+void XHdcp22Tx_ComputeLPrime(const u8* Rn, const u8 *Km,
+                             const u8 *Rrx, const u8 *Rtx,
+                             u8 *LPrime);
+void XHdcp22Tx_ComputeV(const u8* Rn, const u8* Rrx, const u8* RxInfo,
+	                    const u8* Rtx, const u8* RecvIDList, const u8 RecvIDCount,
+	                    const u8* SeqNum_V, const u8* Km, u8* V);
+void XHdcp22Tx_ComputeM(const u8* Rn, const u8* Rrx, const u8* Rtx,
+                        const u8* StreamIDType, const u8* k,
+                        const u8* SeqNum_M, const u8* Km, u8* M);
+void XHdcp22Tx_ComputeEdkeyKs(const u8* Rn, const u8* Km,
+                              const u8 *Ks, const u8 *Rrx,
+                              const u8 *Rtx,  u8 *EdkeyKs);
+int XHdcp22Tx_EncryptKm(const XHdcp22_Tx_CertRx* CertificatePtr,
+                        const u8* KmPtr, u8 *MaskingSeedPtr,
+                        u8* EncryptedKmPtr);
+void XHdcp22Tx_GenerateRandom(XHdcp22_Tx *InstancePtr, int NumOctets,
+                              u8* RandomNumberPtr);
+
+/* Functions for logging */
+void XHdcp22Tx_Dump(const char *string, const u8 *m, u32 mlen);
+void XHdcp22Tx_LogWrNoInst(XHdcp22_Tx_LogEvt Evt, u16 Data);
+
+#ifdef _XHDCP22_TX_TEST_
+/* External functions used for self-testing */
+void XHdcp22Tx_TestSetMode(XHdcp22_Tx *InstancePtr, XHdcp22_Tx_TestMode Mode,
+                           u32 TestFlags);
+u8 XHdcp22Tx_TestCheckResults(XHdcp22_Tx *InstancePtr,
+                              XHdcp22_Tx_LogItem *Expected, u32 nExpected);
+
+/* Internal functions used for self-testing */
+u8   XHdcp22Tx_TestSimulateTimeout(XHdcp22_Tx *InstancePtr);
+void XHdcp22Tx_TestGenerateRtx(XHdcp22_Tx *InstancePtr, u8* RtxPtr);
+void XHdcp22Tx_TestGenerateKm(XHdcp22_Tx *InstancePtr, u8* KmPtr);
+void XHdcp22Tx_TestGenerateKmMaskingSeed(XHdcp22_Tx *InstancePtr, u8* SeedPtr);
+void XHdcp22Tx_TestGenerateRn(XHdcp22_Tx *InstancePtr, u8* RnPtr);
+void XHdcp22Tx_TestGenerateRiv(XHdcp22_Tx *InstancePtr, u8* RivPtr);
+void XHdcp22Tx_TestGenerateKs(XHdcp22_Tx *InstancePtr, u8* KsPtr);
+const u8* XHdcp22Tx_TestGetKPubDpc(XHdcp22_Tx *InstancePtr);
+const u8* XHdcp22Tx_TestGetSrm(XHdcp22_Tx *InstancePtr, u8 Select);
+void XHdcp22Tx_LogDisplayUnitTest(XHdcp22_Tx *InstancePtr);
+#endif
+
+
+/************************** Variable Definitions *****************************/
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* End of protection macro. */
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdcp22_tx_sinit.c
@@ -0,0 +1,97 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdcp22_tx_sinit.c
+* @{
+* @details
+*
+* This file contains static initialization method for Xilinx HDCP 2.2
+* Transmitter driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  JO     16/06/15 Initial release.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xhdcp22_tx.h"
+
+
+/************************** Constant Definitions *****************************/
+#ifndef XPAR_XHDCP22_TX_NUM_INSTANCES
+#define XPAR_XHDCP22_TX_NUM_INSTANCES  0
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XHdcp22_Tx_Config structure based
+* on the core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xhdcp22_tx_g.c file.
+*
+* @param  DeviceId is the unique core ID of the HDCP2.2 TX core for the
+*         lookup operation.
+*
+* @return XHdcp22Tx_LookupConfig returns a reference to a config record
+*         in the configuration table (in xhdcp22_tx_g.c) corresponding
+*         to <i>DeviceId</i>, or NULL if no match is found.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdcp22_Tx_Config *XHdcp22Tx_LookupConfig(u16 DeviceId)
+{
+	extern XHdcp22_Tx_Config XHdcp22_Tx_ConfigTable[XPAR_XHDCP22_TX_NUM_INSTANCES];
+	XHdcp22_Tx_Config *CfgPtr = NULL;
+	u32 Index;
+
+	/* Checking for device id for which instance it is matching */
+	for (Index = (u32)0x0; Index < (u32)(XPAR_XHDCP22_TX_NUM_INSTANCES); Index++) {
+		/* Assigning address of config table if both device ids
+		 * are matched
+		 */
+		if (XHdcp22_Tx_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XHdcp22_Tx_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return CfgPtr;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1.c
@@ -0,0 +1,1377 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1.c
+ *
+ * Contains a minimal set of functions for the XHdmiphy1 driver that allow
+ * access to all of the Video PHY core's functionality. See xhdmiphy1.h for a
+ * detailed description of the driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * 1.1   ku   17/05/20 Adding uniquification to avoid clash with vphy
+ * 1.1   ku   27/07/20 Removed GTHE3 related code
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include <linux/string.h>
+#include "xstatus.h"
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+#include "xhdmiphy1_hdmi.h"
+#include <linux/delay.h>
+#include "xhdmiphy1_gt.h"
+
+/**************************** Function Prototypes *****************************/
+static u32 XHdmiphy1_DrpAccess(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        u16 Addr, u16 *Val);
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function retrieves the configuration for this Video PHY instance and
+ * fills in the InstancePtr->Config structure.
+ *
+ * @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+ * @param	ConfigPtr is a pointer to the configuration structure that will
+ *		be used to copy the settings from.
+ * @param	EffectiveAddr is the device base address in the virtual memory
+ *		space. If the address translation is not used, then the physical
+ *		address is passed.
+ *
+ * @return	None.
+ *
+ * @note	Unexpected errors may occur if the address mapping is changed
+ *		after this function is invoked.
+ *
+*******************************************************************************/
+void XHdmiphy1_CfgInitialize(XHdmiphy1 *InstancePtr,
+		XHdmiphy1_Config *ConfigPtr,
+		UINTPTR EffectiveAddr)
+{
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	u8 Sel;
+#endif
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(ConfigPtr != NULL);
+	Xil_AssertVoid(EffectiveAddr != 0x0);
+
+	(void)memset((void *)InstancePtr, 0, sizeof(XHdmiphy1));
+	InstancePtr->IsReady = 0;
+
+	InstancePtr->Config = *ConfigPtr;
+	InstancePtr->Config.BaseAddr = EffectiveAddr;
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+	InstancePtr->GtAdaptor = &XHdmiphy1_Gthe4Config;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	InstancePtr->GtAdaptor = &XHdmiphy1_Gtye4Config;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+	InstancePtr->GtAdaptor = &Gtye5Config;
+#endif
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	const XHdmiphy1_SysClkDataSelType SysClkCfg[7][2] = {
+		{(XHdmiphy1_SysClkDataSelType)0,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_CPLL_OUTCLK},
+		{(XHdmiphy1_SysClkDataSelType)1,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK},
+		{(XHdmiphy1_SysClkDataSelType)2,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK},
+		{(XHdmiphy1_SysClkDataSelType)3,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL_OUTCLK},
+		{(XHdmiphy1_SysClkDataSelType)4,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_PLL0_OUTCLK},
+		{(XHdmiphy1_SysClkDataSelType)5,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_PLL1_OUTCLK},
+		{(XHdmiphy1_SysClkDataSelType)6,
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK},
+	};
+	for (Sel = 0; Sel < 7; Sel++) {
+		if (InstancePtr->Config.TxSysPllClkSel == SysClkCfg[Sel][0]) {
+			InstancePtr->Config.TxSysPllClkSel = SysClkCfg[Sel][1];
+		}
+		if (InstancePtr->Config.RxSysPllClkSel == SysClkCfg[Sel][0]) {
+			InstancePtr->Config.RxSysPllClkSel = SysClkCfg[Sel][1];
+		}
+	}
+
+	InstancePtr->Config.TxRefClkSel = (XHdmiphy1_PllRefClkSelType)
+			(InstancePtr->Config.TxRefClkSel +
+					XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+	InstancePtr->Config.RxRefClkSel = (XHdmiphy1_PllRefClkSelType)
+			(InstancePtr->Config.RxRefClkSel +
+					XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+	InstancePtr->Config.TxFrlRefClkSel = (XHdmiphy1_PllRefClkSelType)
+			(InstancePtr->Config.TxFrlRefClkSel +
+					XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+	InstancePtr->Config.RxFrlRefClkSel = (XHdmiphy1_PllRefClkSelType)
+			(InstancePtr->Config.RxFrlRefClkSel +
+					XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+	InstancePtr->Config.DruRefClkSel = (XHdmiphy1_PllRefClkSelType)
+			(InstancePtr->Config.DruRefClkSel +
+					XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+#endif
+
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* This function will initialize the PLL selection for a given channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	QpllRefClkSel is the QPLL reference clock selection for the
+*		quad.
+* @param	CpllRefClkSel is the CPLL reference clock selection for the
+*		quad.
+* @param	TxPllSelect is the reference clock selection for the quad's
+*		TX PLL dividers.
+* @param	RxPllSelect is the reference clock selection for the quad's
+*		RX PLL dividers.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_PllInitialize(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId,
+		XHdmiphy1_PllRefClkSelType QpllRefClkSel,
+		XHdmiphy1_PllRefClkSelType CpllRefClkSel,
+		XHdmiphy1_PllType TxPllSelect, XHdmiphy1_PllType RxPllSelect)
+{
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	/* Set configuration in software. */
+    XHdmiphy1_CfgPllRefClkSel(InstancePtr, QuadId,
+            XHDMIPHY1_CHANNEL_ID_CMNA, QpllRefClkSel);
+    XHdmiphy1_CfgPllRefClkSel(InstancePtr, QuadId,
+            XHDMIPHY1_CHANNEL_ID_CHA, CpllRefClkSel);
+	XHdmiphy1_CfgSysClkDataSel(InstancePtr, QuadId, XHDMIPHY1_DIR_TX,
+			XHdmiphy1_Pll2SysClkData(TxPllSelect));
+	XHdmiphy1_CfgSysClkDataSel(InstancePtr, QuadId, XHDMIPHY1_DIR_RX,
+			XHdmiphy1_Pll2SysClkData(RxPllSelect));
+	XHdmiphy1_CfgSysClkOutSel(InstancePtr, QuadId, XHDMIPHY1_DIR_TX,
+			XHdmiphy1_Pll2SysClkOut(TxPllSelect));
+	XHdmiphy1_CfgSysClkOutSel(InstancePtr, QuadId, XHDMIPHY1_DIR_RX,
+			XHdmiphy1_Pll2SysClkOut(RxPllSelect));
+
+	/* Write configuration to hardware at once. */
+	XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, QuadId);
+
+	return XST_SUCCESS;
+}
+#endif
+
+/******************************************************************************/
+/*
+* This function installs a custom delay/sleep function to be used by the
+* XHdmiphy1 driver.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+* @param	CallbackFunc is the address to the callback function.
+* @param	CallbackRef is the user data item (microseconds to delay) that
+*		will be passed to the custom sleep/delay function when it is
+*		invoked.
+*
+* @return	None.
+*
+* @note		None.
+*
+*******************************************************************************/
+void XHdmiphy1_SetUserTimerHandler(XHdmiphy1 *InstancePtr,
+		XHdmiphy1_TimerHandler CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	InstancePtr->UserTimerWaitUs = CallbackFunc;
+	InstancePtr->UserTimerPtr = CallbackRef;
+}
+
+/******************************************************************************/
+/**
+* This function is the delay/sleep function for the XHdmiphy1 driver. For the
+* Zynq family, there exists native sleep functionality. For MicroBlaze however,
+* there does not exist such functionality. In the MicroBlaze case, the default
+* method for delaying is to use a predetermined amount of loop iterations. This
+* method is prone to inaccuracy and dependent on system configuration; for
+* greater accuracy, the user may supply their own delay/sleep handler, pointed
+* to by InstancePtr->UserTimerWaitUs, which may have better accuracy if a
+* hardware timer is used.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+* @param	MicroSeconds is the number of microseconds to delay/sleep for.
+*
+* @return	None.
+*
+* @note		None.
+*
+*******************************************************************************/
+void XHdmiphy1_WaitUs(XHdmiphy1 *InstancePtr, u32 MicroSeconds)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	if (MicroSeconds == 0) {
+		return;
+	}
+
+	if (InstancePtr->UserTimerWaitUs != NULL) {
+		/* Use the timer handler specified by the user for better
+		 * accuracy. */
+		InstancePtr->UserTimerWaitUs(InstancePtr, MicroSeconds);
+	}
+	else {
+	    /* Wait the requested amount of time. */
+	    usleep_range(MicroSeconds, MicroSeconds + MicroSeconds/10);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will obtian the IP version.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	The IP version of the Video PHY core.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_GetVersion(XHdmiphy1 *InstancePtr)
+{
+	return XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+                XHDMIPHY1_VERSION_REG);
+}
+
+/*****************************************************************************/
+/**
+* Configure the channel's line rate. This is a software only configuration and
+* this value is used in the PLL calculator.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	LineRate is the line rate to configure software.
+*
+* @return
+*		- XST_SUCCESS if the reference clock type is valid.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_CfgLineRate(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u64 LineRateHz)
+{
+	u8 Id;
+	u8 Id0;
+	u8 Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].LineRateHz =
+								LineRateHz;
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* Obtain the channel's PLL reference clock selection.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return	The PLL type being used by the channel.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdmiphy1_PllType XHdmiphy1_GetPllType(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, XHdmiphy1_ChannelId ChId)
+{
+	XHdmiphy1_PllType PllType;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_SysClkDataSelType SysClkDataSel;
+	XHdmiphy1_SysClkOutSelType SysClkOutSel;
+
+	SysClkDataSel = XHdmiphy1_GetSysClkDataSel(InstancePtr, QuadId, Dir, ChId);
+	SysClkOutSel = XHdmiphy1_GetSysClkOutSel(InstancePtr, QuadId, Dir, ChId);
+
+	/* The sysclk data and output reference clocks should match. */
+
+	if ((SysClkDataSel == XHDMIPHY1_SYSCLKSELDATA_TYPE_CPLL_OUTCLK) &&
+	(SysClkOutSel == XHDMIPHY1_SYSCLKSELOUT_TYPE_CPLL_REFCLK)) {
+		PllType = XHDMIPHY1_PLL_TYPE_CPLL;
+	}
+	else if ((SysClkDataSel == XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL_OUTCLK) &&
+	(SysClkOutSel == XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL_REFCLK)) {
+		PllType = XHDMIPHY1_PLL_TYPE_QPLL;
+	}
+	else if ((SysClkDataSel == XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK) &&
+	(SysClkOutSel == XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL0_REFCLK)) {
+		PllType = XHDMIPHY1_PLL_TYPE_QPLL0;
+	}
+	else if ((SysClkDataSel == XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK) &&
+	(SysClkOutSel == XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL1_REFCLK)) {
+		PllType = XHDMIPHY1_PLL_TYPE_QPLL1;
+	}
+	else {
+		PllType = XHDMIPHY1_PLL_TYPE_UNKNOWN;
+	}
+#else
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	ChId = ChId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		PllType = (XHdmiphy1_PllType) InstancePtr->Config.TxSysPllClkSel-2;
+	}
+	else if (Dir == XHDMIPHY1_DIR_RX) {
+		PllType = (XHdmiphy1_PllType) InstancePtr->Config.RxSysPllClkSel-2;
+	}
+	else {
+		PllType = XHDMIPHY1_PLL_TYPE_UNKNOWN;
+	}
+#endif
+
+	return PllType;
+}
+
+/*****************************************************************************/
+/**
+* This function will return the line rate in Hz for a given channel / quad.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to check.
+* @param	ChId is the channel ID for which to retrieve the line rate.
+*
+* @return	The line rate in Hz.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdmiphy1_GetLineRateHz(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid((ChId < XHDMIPHY1_CHANNEL_ID_CMNA));
+
+	XHdmiphy1_ChannelId Ch_Id = ChId;
+
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		Ch_Id = XHDMIPHY1_CHANNEL_ID_CH1;
+	} else if (ChId == XHDMIPHY1_CHANNEL_ID_CMNA) {
+		Ch_Id = XHDMIPHY1_CHANNEL_ID_CMN0;
+	}
+
+	return InstancePtr->Quads[QuadId].Plls[Ch_Id -
+		XHDMIPHY1_CHANNEL_ID_CH1].LineRateHz;
+}
+
+/*****************************************************************************/
+/**
+* This function will reset the GT's PLL logic.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_ResetGtPll(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Hold)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_TX_INIT_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_RX_INIT_REG;
+	}
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		MaskVal = XHDMIPHY1_TXRX_INIT_PLLGTRESET_ALL_MASK;
+	}
+	else {
+		MaskVal = XHDMIPHY1_TXRX_INIT_PLLGTRESET_MASK(ChId);
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	/* Assert reset. */
+	RegVal |= MaskVal;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~MaskVal;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will reset the GT's TX/RX logic.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_ResetGtTxRx(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Hold)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_TX_INIT_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_RX_INIT_REG;
+	}
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		MaskVal =  XHDMIPHY1_TXRX_INIT_GTRESET_ALL_MASK;
+	}
+	else {
+		MaskVal = XHDMIPHY1_TXRX_INIT_GTRESET_MASK(ChId);
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	/* Assert reset. */
+	RegVal |= MaskVal;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~MaskVal;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set/clear the TX/RX polarity bit.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Polarity 0-Not inverted 1-Inverted
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_SetPolarity(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Polarity)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_TX_CONTROL_REG;
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+			MaskVal =  XHDMIPHY1_TX_CONTROL_TXPOLARITY_ALL_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_TX_CONTROL_TXPOLARITY_MASK(ChId);
+		}
+	}
+	else {
+		RegOffset = XHDMIPHY1_RX_CONTROL_REG;
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+			MaskVal = XHDMIPHY1_RX_CONTROL_RXPOLARITY_ALL_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_RX_CONTROL_RXPOLARITY_MASK(ChId);
+		}
+	}
+
+	/* Read TX|RX Control Register */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Clear Polarity Register bits */
+	RegVal &= ~MaskVal;
+
+	if (Polarity) {
+		RegVal |= MaskVal;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX/RXPRBSEL of the GT
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Pattern is the pattern XHdmiphy1_PrbsPattern
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_SetPrbsSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        XHdmiphy1_PrbsPattern Pattern)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+	u32 PrbsEnc = 0x0;
+	u8 Id, Id0, Id1;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_TX_CONTROL_REG;
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+			MaskVal =  XHDMIPHY1_TX_CONTROL_TXPRBSSEL_ALL_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_TX_CONTROL_TXPRBSSEL_MASK(ChId);
+		}
+		PrbsEnc = (u32) (((Pattern & 0x8) << 1) | (Pattern & 0x7));
+	}
+	else {
+		RegOffset = XHDMIPHY1_RX_CONTROL_REG;
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+			MaskVal = XHDMIPHY1_RX_CONTROL_RXPRBSSEL_ALL_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_RX_CONTROL_RXPRBSSEL_MASK(ChId);
+		}
+		PrbsEnc = (u32) (Pattern & 0xF);
+	}
+
+	/* Read TX|RX Control Register */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Mask out PRBS Register bits */
+	RegVal &= ~MaskVal;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		RegVal |= PrbsEnc << ((Dir == XHDMIPHY1_DIR_TX) ?
+					XHDMIPHY1_TX_CONTROL_TXPRBSSEL_SHIFT(Id) :
+					XHDMIPHY1_RX_CONTROL_RXPRBSSEL_SHIFT(Id));
+	}
+
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX/RXPRBSEL of the GT
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ForceErr 0-No Error 1-Force Error
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_TxPrbsForceError(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, u8 ForceErr)
+{
+	u32 RegVal;
+	u32 MaskVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		MaskVal =  XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_ALL_MASK;
+	}
+	else {
+		MaskVal = XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_MASK(ChId);
+	}
+
+	/* Read TX|RX Control Register */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_TX_CONTROL_REG);
+
+	/* Clear Polarity Register bits */
+	RegVal &= ~MaskVal;
+
+	if (ForceErr) {
+		RegVal |= MaskVal;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_TX_CONTROL_REG, RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX voltage swing value for a given channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Vs is the voltage swing value to write.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_SetTxVoltageSwing(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, u8 Vs)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+        (ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+		RegOffset = XHDMIPHY1_TX_DRIVER_CH12_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_TX_DRIVER_CH34_REG;
+	}
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	MaskVal = XHDMIPHY1_TX_DRIVER_TXDIFFCTRL_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= ((Vs & 0xF) << XHDMIPHY1_TX_DRIVER_TXDIFFCTRL_SHIFT(ChId));
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_TX_DRIVER_EXT_REG);
+	MaskVal = XHDMIPHY1_TX_DRIVER_EXT_TXDIFFCTRL_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= ((Vs && 0x10) <<
+			XHDMIPHY1_TX_DRIVER_EXT_TXDIFFCTRL_SHIFT(ChId));
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_TX_DRIVER_EXT_REG, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX pre-emphasis value for a given channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Pe is the pre-emphasis value to write.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_SetTxPreEmphasis(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Pe)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+        (ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+		RegOffset = XHDMIPHY1_TX_DRIVER_CH12_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_TX_DRIVER_CH34_REG;
+	}
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	MaskVal = XHDMIPHY1_TX_DRIVER_TXPRECURSOR_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= (Pe << XHDMIPHY1_TX_DRIVER_TXPRECURSOR_SHIFT(ChId));
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX post-curosr value for a given channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Pe is the pre-emphasis value to write.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_SetTxPostCursor(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Pc)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+        (ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+		RegOffset = XHDMIPHY1_TX_DRIVER_CH12_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_TX_DRIVER_CH34_REG;
+	}
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	MaskVal = XHDMIPHY1_TX_DRIVER_TXPOSTCURSOR_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= (Pc << XHDMIPHY1_TX_DRIVER_TXPOSTCURSOR_SHIFT(ChId));
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will enable or disable the LPM logic in the Video PHY core.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable will enable (if 1) or disable (if 0) the LPM logic.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_SetRxLpm(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Enable)
+{
+	u32 RegVal;
+	u32 MaskVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	Dir = Dir;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+							XHDMIPHY1_RX_EQ_CDR_REG);
+
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		MaskVal = XHDMIPHY1_RX_CONTROL_RXLPMEN_ALL_MASK;
+	}
+	else {
+		MaskVal = XHDMIPHY1_RX_CONTROL_RXLPMEN_MASK(ChId);
+	}
+
+	if (Enable) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_RX_EQ_CDR_REG,
+									RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will initiate a write DRP transaction. It is a wrapper around
+* XHdmiphy1_DrpAccess.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID on which to direct the DRP access.
+* @param	Addr is the DRP address to issue the DRP access to.
+* @param	Val is the value to write to the DRP address.
+*
+* @return
+*		- XST_SUCCESS if the DRP access was successful.
+*		- XST_FAILURE otherwise, if the busy bit did not go low, or if
+*		  the ready bit did not go high.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_DrpWr(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u16 Addr, u16 Val)
+{
+	return XHdmiphy1_DrpAccess(InstancePtr, QuadId, ChId,
+			XHDMIPHY1_DIR_TX, /* Write. */
+			Addr, &Val);
+}
+
+/*****************************************************************************/
+/**
+* This function will initiate a read DRP transaction. It is a wrapper around
+* XHdmiphy1_DrpAccess.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID on which to direct the DRP access.
+* @param	Addr is the DRP address to issue the DRP access to.
+* @param	RetVal is the DRP read_value returned implicitly.
+*
+* @return
+*		- XST_SUCCESS if the DRP access was successful.
+*		- XST_FAILURE otherwise, if the busy bit did not go low, or if
+*		  the ready bit did not go high.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XHdmiphy1_DrpRd(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u16 Addr, u16 *RetVal)
+{
+	u32 Status;
+	u16 Val;
+
+	Status = XHdmiphy1_DrpAccess(InstancePtr, QuadId, ChId,
+			XHDMIPHY1_DIR_RX, /* Read. */
+			Addr, &Val);
+
+    *RetVal = Val;
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will power down the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the power down if set
+*		to 1. If set to 0: power down, then power back up.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_MmcmPowerDown(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u8 Hold)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	/* Power down. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+	RegVal |= XHDMIPHY1_MMCM_USRCLK_CTRL_PWRDWN_MASK;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	if (!Hold) {
+		/* Power up. */
+		RegVal &= ~XHDMIPHY1_MMCM_USRCLK_CTRL_PWRDWN_MASK;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl,
+									RegVal);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will start the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_MmcmStart(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir)
+{
+	XHdmiphy1_Mmcm *MmcmPtr;
+
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		MmcmPtr= &InstancePtr->Quads[QuadId].RxMmcm;
+	}
+	else {
+		MmcmPtr= &InstancePtr->Quads[QuadId].TxMmcm;
+	}
+
+	/* Check values if valid */
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	if (!((MmcmPtr->ClkOut0Div > 0) && (MmcmPtr->ClkOut0Div <= 128) &&
+		  (MmcmPtr->ClkOut1Div > 0) && (MmcmPtr->ClkOut1Div <= 128) &&
+		  (MmcmPtr->ClkOut2Div > 0) && (MmcmPtr->ClkOut2Div <= 128))) {
+#else
+	if (!((MmcmPtr->ClkOut0Div > 0) && (MmcmPtr->ClkOut0Div <= 432) &&
+		  (MmcmPtr->ClkOut1Div > 0) && (MmcmPtr->ClkOut1Div <= 432) &&
+		  (MmcmPtr->ClkOut2Div > 0) && (MmcmPtr->ClkOut2Div <= 432))) {
+#endif
+		return;
+	}
+
+	/* Assert MMCM reset. */
+	XHdmiphy1_MmcmReset(InstancePtr, QuadId, Dir, TRUE);
+
+	/* Configure MMCM. */
+	XHdmiphy1_MmcmWriteParameters(InstancePtr, QuadId, Dir);
+
+	/* Release MMCM reset. */
+	XHdmiphy1_MmcmReset(InstancePtr, QuadId, Dir, FALSE);
+
+	/* Unmask the MMCM Lock */
+	XHdmiphy1_MmcmLockedMaskEnable(InstancePtr, 0, Dir, FALSE);
+
+	XHdmiphy1_LogWrite(InstancePtr, (Dir == XHDMIPHY1_DIR_TX) ?
+		XHDMIPHY1_LOG_EVT_TXPLL_RECONFIG :
+		XHDMIPHY1_LOG_EVT_RXPLL_RECONFIG, 1);
+}
+
+/*****************************************************************************/
+/**
+* This function enables the TX or RX IBUFDS peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the IBUFDS, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_IBufDsEnable(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u8 Enable)
+{
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_PllRefClkSelType *TypePtr, *DruTypePtr, DruTypeDummy;
+	DruTypeDummy = XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTGREFCLK;
+	DruTypePtr = &DruTypeDummy;
+#endif
+	u32 RegAddr = XHDMIPHY1_IBUFDS_GTXX_CTRL_REG;
+	u32 RegVal;
+	u32 MaskVal = 0;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		TypePtr = &InstancePtr->Config.TxRefClkSel;
+	}
+	else {
+		TypePtr = &InstancePtr->Config.RxRefClkSel;
+		if (InstancePtr->Config.DruIsPresent) {
+			DruTypePtr = &InstancePtr->Config.DruRefClkSel;
+		}
+	}
+
+	if ((*TypePtr == XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0) ||
+			((InstancePtr->Config.DruIsPresent) &&
+			(*DruTypePtr == XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0))) {
+		MaskVal = XHDMIPHY1_IBUFDS_GTXX_CTRL_GTREFCLK0_CEB_MASK;
+	}
+	else if ((*TypePtr == XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK1) ||
+			((InstancePtr->Config.DruIsPresent) &&
+			(*DruTypePtr == XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK1))) {
+		MaskVal = XHDMIPHY1_IBUFDS_GTXX_CTRL_GTREFCLK1_CEB_MASK;
+	}
+	else {
+#endif
+		if (Dir == XHDMIPHY1_DIR_TX) {
+			RegAddr = XHDMIPHY1_MISC_TXUSRCLK_REG;
+		}
+		else {
+			RegAddr = XHDMIPHY1_MISC_RXUSRCLK_REG;
+		}
+		MaskVal = XHDMIPHY1_MISC_XXUSRCLK_REFCLK_CEB_MASK;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	}
+#endif
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegAddr);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	if (Enable) {
+		RegVal &= ~MaskVal;
+	}
+	else {
+		RegVal |= MaskVal;
+	}
+#else
+	if (Enable) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+#endif
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegAddr, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function enables the TX or RX CLKOUT1 OBUFTDS peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the OBUFTDS, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_Clkout1OBufTdsEnable(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir, u8 Enable)
+{
+	u32 RegVal;
+	u32 RegOffset;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_MISC_TXUSRCLK_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_MISC_RXUSRCLK_REG;
+	}
+
+	/* Read XXUSRCLK MISC register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Write new value to XXUSRCLK MISC register. */
+	if (Enable) {
+		RegVal |= XHDMIPHY1_MISC_XXUSRCLK_CKOUT1_OEN_MASK;
+	}
+	else {
+		RegVal &= ~XHDMIPHY1_MISC_XXUSRCLK_CKOUT1_OEN_MASK;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will initiate a DRP transaction (either read or write).
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID on which to direct the DRP access.
+* @param	Dir is an indicator for write (TX) or read (RX).
+* @param	Addr is the DRP address to issue the DRP access to.
+* @param	Val is a pointer to the data value. In write mode, this pointer
+*		will hold the value to write. In read mode, this pointer will
+*		be populated with the read value.
+*
+* @return
+*		- XST_SUCCESS if the DRP access was successful.
+*		- XST_FAILURE otherwise, if the busy bit did not go low, or if
+*		  the ready bit did not go high.
+*
+* @note		In read mode (Dir == XHDMIPHY1_DIR_RX), the data pointed to by Val
+*		will be populated with the u16 value that was read._
+*
+******************************************************************************/
+static u32 XHdmiphy1_DrpAccess(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        u16 Addr, u16 *Val)
+{
+	u32 RegOffsetCtrl;
+	u32 RegOffsetSts;
+	u32 RegVal;
+	u8 Retry;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	/* Determine which DRP registers to use based on channel. */
+	if (XHDMIPHY1_ISCMN(ChId)) {
+		RegOffsetCtrl = XHDMIPHY1_DRP_CONTROL_COMMON_REG;
+		RegOffsetSts = XHDMIPHY1_DRP_STATUS_COMMON_REG;
+	}
+	else if (XHDMIPHY1_ISTXMMCM(ChId)) {
+		RegOffsetCtrl = XHDMIPHY1_DRP_CONTROL_TXMMCM_REG;
+		RegOffsetSts = XHDMIPHY1_DRP_STATUS_TXMMCM_REG;
+	}
+	else if (XHDMIPHY1_ISRXMMCM(ChId)) {
+		RegOffsetCtrl = XHDMIPHY1_DRP_CONTROL_RXMMCM_REG;
+		RegOffsetSts = XHDMIPHY1_DRP_STATUS_RXMMCM_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_DRP_CONTROL_CH1_REG +
+			(4 * XHDMIPHY1_CH2IDX(ChId));
+		RegOffsetSts = XHDMIPHY1_DRP_STATUS_CH1_REG +
+			(4 * (XHDMIPHY1_CH2IDX(ChId)));
+	}
+
+	/* Wait until the DRP status indicates that it is not busy.*/
+	Retry = 0;
+	do {
+		RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+								RegOffsetSts);
+		if (Retry > 150) {
+			return XST_FAILURE;
+		}
+		Retry++;
+	} while (RegVal & XHDMIPHY1_DRP_STATUS_DRPBUSY_MASK);
+
+	/* Write the command to the channel's DRP. */
+	RegVal = (Addr & XHDMIPHY1_DRP_CONTROL_DRPADDR_MASK);
+	RegVal |= XHDMIPHY1_DRP_CONTROL_DRPEN_MASK;
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		/* Enable write. */
+		RegVal |= XHDMIPHY1_DRP_CONTROL_DRPWE_MASK;
+		RegVal |= ((*Val << XHDMIPHY1_DRP_CONTROL_DRPDI_SHIFT) &
+						XHDMIPHY1_DRP_CONTROL_DRPDI_MASK);
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	/* Wait until the DRP status indicates ready.*/
+	Retry = 0;
+	do {
+		RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+								RegOffsetSts);
+		if (Retry > 150) {
+			return XST_FAILURE;
+		}
+		Retry++;
+	} while (!(RegVal & XHDMIPHY1_DRP_STATUS_DRPRDY_MASK));
+
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		/* Mask non-data out for read. */
+		RegVal &= XHDMIPHY1_DRP_STATUS_DRPO_MASK;
+		/* Populate Val with read contents. */
+		*Val = RegVal;
+	}
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function installs a callback function for the HDMIPHY error conditions
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+* @param	CallbackFunc is the address to the callback function.
+* @param	CallbackRef is the user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return	None.
+*
+* @note		The XHdmiphy1_ErrorHandler API calls the registered function in
+* 			  ErrorCallback and passes two arguments: 1) CallbackRef
+* 			  2) Error Type as defined by XHdmiphy1_ErrType.
+*
+* 			Sample Function Call:
+* 				CallbackFunc(CallbackRef, XHdmiphy1_ErrType);
+*
+******************************************************************************/
+void XHdmiphy1_SetErrorCallback(XHdmiphy1 *InstancePtr,
+		void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	InstancePtr->ErrorCallback = (XHdmiphy1_ErrorCallback)CallbackFunc;
+	InstancePtr->ErrorRef = CallbackRef;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs an asynchronous callback function for the LogWrite
+* API:
+*
+* @param    InstancePtr is a pointer to the XHdmiphy1 instance.
+* @param    CallbackFunc is the address of the callback function.
+* @param    CallbackRef is a user data item that will be passed to the
+*       callback function when it is invoked.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_SetLogCallback(XHdmiphy1 *InstancePtr,
+		u64 *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	InstancePtr->LogWriteCallback = (XHdmiphy1_LogCallback)CallbackFunc;
+	InstancePtr->LogWriteRef = CallbackRef;
+}
+
+/*****************************************************************************/
+/**
+* This function prints out Video PHY register and GT Channel and Common
+* DRP register contents.
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_RegisterDebug(XHdmiphy1 *InstancePtr)
+{
+	u32 RegOffset;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	u16 DrpAddr, MaxDrpAddr;
+	u16 DrpVal, ChId;
+	u8  MaxChannels;
+#endif
+
+	xil_printf("\r\nHDMIPHY Registers\r\n");
+	xil_printf("-----------------\r\n");
+	xil_printf("Offset   |  Value\r\n");
+	xil_printf("-----------------\r\n");
+	for (RegOffset = 0; RegOffset <= 0x334; ) {
+		xil_printf("0x%04x      0x%08x\r\n",RegOffset,
+		XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset));
+		RegOffset += 4;
+	}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+	MaxDrpAddr = 0x00B0;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	MaxDrpAddr = 0x00B0;
+#endif
+
+	xil_printf("\r\nHDMIPHY GT COMMON DRP Registers\r\n");
+	xil_printf("----------------------------\r\n");
+	if (InstancePtr->HdmiIsQpllPresent == TRUE) {
+		xil_printf("Offset   |  Value\r\n");
+		xil_printf("----------------------------\r\n");
+		for (DrpAddr = 0x0000; DrpAddr <= MaxDrpAddr; DrpAddr++) {
+			XHdmiphy1_DrpRd(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CMN0,
+					DrpAddr, &DrpVal);
+			xil_printf("0x%04x      0x%04x\r\n",DrpAddr, DrpVal);
+		}
+	} else {
+		xil_printf("No QPLL in this HDMIPHY Instance\r\n");
+	}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+	MaxDrpAddr = 0x0125;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	MaxDrpAddr = 0x0135;
+#endif
+	/* Get Max number of channels in HDMIPHY */
+	MaxChannels = (InstancePtr->Config.RxChannels >
+					InstancePtr->Config.TxChannels) ?
+					InstancePtr->Config.RxChannels :
+					InstancePtr->Config.TxChannels;
+
+	for (ChId = 1; ChId <= MaxChannels; ChId++) {
+	xil_printf("\r\nHDMIPHY GT CHANNEL %d DRP Registers\r\n", ChId);
+	xil_printf("-------------------------------\r\n");
+	xil_printf("Offset   |  Value\r\n");
+	xil_printf("-------------------------------\r\n");
+		for (DrpAddr = 0x0000; DrpAddr <= MaxDrpAddr; DrpAddr++) {
+			XHdmiphy1_DrpRd(InstancePtr, 0, ChId, DrpAddr, &DrpVal);
+			xil_printf("0x%04x      0x%04x\r\n",DrpAddr, DrpVal);
+		}
+	}
+#endif
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1.h
@@ -0,0 +1,1029 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1.h
+ * @addtogroup xhdmiphy1_v1_0
+ * @{
+ * @details
+ * This is main header file of the Xilinx HDMI PHY Controller driver
+ *
+ * <b>Video PHY Controller Overview</b>
+ *
+ * The PHY is intended to simplify the use of serial transceivers and adds
+ * domain-specific configurability. The Video PHY Controller IP is not intended
+ * to be used as a stand alone IP and must be used with Xilinx Video MACs such
+ * as HDMI 2.1 Transmitter/Receiver Subsystems. The core enables simpler
+ * connectivity between MAC layers for TX and RX paths. However, it is still
+ * important to understand the behavior, usage, and any limitations of the
+ * transceivers. See the device specific transceiver user guide for details.
+ *
+ * <b>Video PHY Controller Driver Features</b>
+ *
+ * Video PHY Controller driver supports following features
+ *   - Xilinx HDMI 2.1 MAC IP
+ *   - GTHE3, GTHE4 and GTYE4 GT types
+ *   - HDMI:
+ *   -   4 pixel-wide video interface
+ *   -   8/10/12 bits per component
+ *   -   RGB & YCbCr color space
+ *   -   Up to 10k resolution at both Input and Output interface
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+#ifndef XHDMIPHY1_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XHDMIPHY1_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if !defined(XV_CONFIG_LOG_HDMIPHY1_DISABLE) && \
+    !defined(XV_CONFIG_LOG_DISABLE_ALL)
+#define XV_HDMIPHY1_LOG_ENABLE
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xil_assert.h"
+#include "xhdmiphy1_hw.h"
+#include "xvidc.h"
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+#define XHDMIPHY1_GTHE4 5
+#define XHDMIPHY1_GTYE4 6
+#define XHDMIPHY1_GTYE5 7
+
+/****************************** Type Definitions ******************************/
+
+/* This typedef enumerates the different GT types available. */
+typedef enum {
+    XHDMIPHY1_GT_TYPE_GTHE4 = 5,
+    XHDMIPHY1_GT_TYPE_GTYE4 = 6,
+    XHDMIPHY1_GT_TYPE_GTYE5 = 7,
+} XHdmiphy1_GtType;
+
+/**
+ * This typedef enumerates the various protocols handled by the Video PHY
+ * controller (HDMIPHY).
+ */
+typedef enum {
+    XHDMIPHY1_PROTOCOL_HDMI   = 1,
+    XHDMIPHY1_PROTOCOL_HDMI21 = 2,
+    XHDMIPHY1_PROTOCOL_NONE   = 3
+} XHdmiphy1_ProtocolType;
+
+/* This typedef enumerates is used to specify RX/TX direction information. */
+typedef enum {
+    XHDMIPHY1_DIR_RX = 0,
+    XHDMIPHY1_DIR_TX,
+    XHDMIPHY1_DIR_NONE
+} XHdmiphy1_DirectionType;
+
+/**
+ * This typedef enumerates the list of available interrupt handler types. The
+ * values are used as parameters to the XHdmiphy1_SetIntrHandler function.
+ */
+typedef enum {
+    XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE =
+        XHDMIPHY1_INTR_TXRESETDONE_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE =
+        XHDMIPHY1_INTR_RXRESETDONE_MASK,
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    XHDMIPHY1_INTR_HANDLER_TYPE_CPLL_LOCK =
+        XHDMIPHY1_INTR_CPLL_LOCK_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_QPLL_LOCK =
+        XHDMIPHY1_INTR_QPLL_LOCK_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_QPLL0_LOCK =
+        XHDMIPHY1_INTR_QPLL_LOCK_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_TXALIGN_DONE =
+        XHDMIPHY1_INTR_TXALIGNDONE_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_QPLL1_LOCK =
+        XHDMIPHY1_INTR_QPLL1_LOCK_MASK,
+#else
+    XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK =
+        XHDMIPHY1_INTR_LCPLL_LOCK_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK =
+        XHDMIPHY1_INTR_RPLL_LOCK_MASK,
+#endif
+    XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE =
+        XHDMIPHY1_INTR_TXCLKDETFREQCHANGE_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE =
+        XHDMIPHY1_INTR_RXCLKDETFREQCHANGE_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE =
+        XHDMIPHY1_INTR_TXMMCMUSRCLK_LOCK_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE =
+        XHDMIPHY1_INTR_RXMMCMUSRCLK_LOCK_MASK,
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+    XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE =
+	XHDMIPHY1_INTR_TXGPO_RE_MASK,
+	XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE =
+	XHDMIPHY1_INTR_RXGPO_RE_MASK,
+#endif
+    XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT =
+        XHDMIPHY1_INTR_TXTMRTIMEOUT_MASK,
+    XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT =
+        XHDMIPHY1_INTR_RXTMRTIMEOUT_MASK,
+} XHdmiphy1_IntrHandlerType;
+
+/**
+ * This typedef enumerates the list of available hdmi handler types. The
+ * values are used as parameters to the XHdmiphy1_SetHdmiCallback function.
+ */
+typedef enum {
+    XHDMIPHY1_HDMI_HANDLER_TXINIT = 1,   /**< TX init handler. */
+    XHDMIPHY1_HDMI_HANDLER_TXREADY,      /**< TX ready handler. */
+    XHDMIPHY1_HDMI_HANDLER_RXINIT,       /**< RX init handler. */
+    XHDMIPHY1_HDMI_HANDLER_RXREADY       /**< RX ready handler. */
+} XHdmiphy1_HdmiHandlerType;
+
+/**
+ * This typedef enumerates the different PLL types for a given GT channel.
+ */
+typedef enum {
+    XHDMIPHY1_PLL_TYPE_CPLL    = 1,
+    XHDMIPHY1_PLL_TYPE_QPLL    = 2,
+    XHDMIPHY1_PLL_TYPE_QPLL0   = 3,
+    XHDMIPHY1_PLL_TYPE_QPLL1   = 4,
+    XHDMIPHY1_PLL_TYPE_LCPLL   = 5,
+    XHDMIPHY1_PLL_TYPE_RPLL    = 6,
+    XHDMIPHY1_PLL_TYPE_UNKNOWN = 7,
+} XHdmiphy1_PllType;
+
+/**
+ * This typedef enumerates the available channels.
+ */
+typedef enum {
+    XHDMIPHY1_CHANNEL_ID_CH1    = 1,
+    XHDMIPHY1_CHANNEL_ID_CH2    = 2,
+    XHDMIPHY1_CHANNEL_ID_CH3    = 3,
+    XHDMIPHY1_CHANNEL_ID_CH4    = 4,
+    XHDMIPHY1_CHANNEL_ID_CMN0   = 5, /* QPLL, QPLL0, LCPLL */
+    XHDMIPHY1_CHANNEL_ID_CMN1   = 6, /* QPLL1, RPLL */
+    XHDMIPHY1_CHANNEL_ID_CHA    = 7,
+    XHDMIPHY1_CHANNEL_ID_CMNA   = 8,
+    XHDMIPHY1_CHANNEL_ID_TXMMCM = 9,
+    XHDMIPHY1_CHANNEL_ID_RXMMCM = 10,
+    XHDMIPHY1_CHANNEL_ID_CMN = XHDMIPHY1_CHANNEL_ID_CMN0,
+} XHdmiphy1_ChannelId;
+
+/**
+ * This typedef enumerates the available reference clocks for the PLL clock
+ * selection multiplexer.
+ */
+typedef enum {
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTREFCLK0,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK1 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTREFCLK1,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTNORTHREFCLK0 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTNORTHREFCLK0,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTNORTHREFCLK1 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTNORTHREFCLK1,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTSOUTHREFCLK0 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTSOUTHREFCLK0,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTSOUTHREFCLK1 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTSOUTHREFCLK1,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTEASTREFCLK0 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTEASTREFCLK0,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTEASTREFCLK1 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTEASTREFCLK1,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTWESTREFCLK0 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTWESTREFCLK0,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTWESTREFCLK1 =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTWESTREFCLK1,
+    XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTGREFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XPLL_GTGREFCLK,
+} XHdmiphy1_PllRefClkSelType;
+
+/**
+ * This typedef enumerates the available reference clocks used to drive the
+ * RX/TX datapaths.
+ */
+typedef enum {
+    XHDMIPHY1_SYSCLKSELDATA_TYPE_PLL0_OUTCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL0,
+    XHDMIPHY1_SYSCLKSELDATA_TYPE_PLL1_OUTCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL1,
+    XHDMIPHY1_SYSCLKSELDATA_TYPE_CPLL_OUTCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_CPLL,
+    XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL_OUTCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL,
+    XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL0,
+    XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL1,
+} XHdmiphy1_SysClkDataSelType;
+
+/**
+ * This typedef enumerates the available reference clocks used to drive the
+ * RX/TX output clocks.
+ */
+typedef enum {
+    XHDMIPHY1_SYSCLKSELOUT_TYPE_CPLL_REFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CH,
+    XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL_REFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN,
+    XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL0_REFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN0,
+    XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL1_REFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN1,
+    XHDMIPHY1_SYSCLKSELOUT_TYPE_PLL0_REFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CH,
+    XHDMIPHY1_SYSCLKSELOUT_TYPE_PLL1_REFCLK =
+        XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN,
+} XHdmiphy1_SysClkOutSelType;
+
+/**
+ * This typedef enumerates the available clocks that are used as multiplexer
+ * input selections for the RX/TX output clock.
+ */
+typedef enum {
+    XHDMIPHY1_OUTCLKSEL_TYPE_OUTCLKPCS = 1,
+    XHDMIPHY1_OUTCLKSEL_TYPE_OUTCLKPMA,
+    XHDMIPHY1_OUTCLKSEL_TYPE_PLLREFCLK_DIV1,
+    XHDMIPHY1_OUTCLKSEL_TYPE_PLLREFCLK_DIV2,
+    XHDMIPHY1_OUTCLKSEL_TYPE_PROGDIVCLK
+} XHdmiphy1_OutClkSelType;
+
+/* This typedef enumerates the possible states a transceiver can be in. */
+typedef enum {
+    XHDMIPHY1_GT_STATE_IDLE,     /**< Idle state. */
+	XHDMIPHY1_GT_STATE_GPO_RE,   /**< GPO RE state. */
+    XHDMIPHY1_GT_STATE_LOCK,     /**< Lock state. */
+    XHDMIPHY1_GT_STATE_RESET,    /**< Reset state. */
+    XHDMIPHY1_GT_STATE_ALIGN,    /**< Align state. */
+    XHDMIPHY1_GT_STATE_READY,    /**< Ready state. */
+} XHdmiphy1_GtState;
+
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+typedef enum {
+    XHDMIPHY1_LOG_EVT_NONE = 1,      /**< Log event none. */
+    XHDMIPHY1_LOG_EVT_QPLL_EN,       /**< Log event QPLL enable. */
+    XHDMIPHY1_LOG_EVT_QPLL_RST,      /**< Log event QPLL reset. */
+    XHDMIPHY1_LOG_EVT_QPLL_LOCK,     /**< Log event QPLL lock. */
+    XHDMIPHY1_LOG_EVT_QPLL_RECONFIG, /**< Log event QPLL reconfig. */
+    XHDMIPHY1_LOG_EVT_QPLL0_EN,      /**< Log event QPLL0 enable. */
+    XHDMIPHY1_LOG_EVT_QPLL0_RST,     /**< Log event QPLL0 reset. */
+    XHDMIPHY1_LOG_EVT_QPLL0_LOCK,    /**< Log event QPLL0 lock. */
+    XHDMIPHY1_LOG_EVT_QPLL0_RECONFIG,/**< Log event QPLL0 reconfig. */
+    XHDMIPHY1_LOG_EVT_QPLL1_EN,      /**< Log event QPLL1 enable. */
+    XHDMIPHY1_LOG_EVT_QPLL1_RST,     /**< Log event QPLL1 reset. */
+    XHDMIPHY1_LOG_EVT_QPLL1_LOCK,    /**< Log event QPLL1 lock. */
+    XHDMIPHY1_LOG_EVT_QPLL1_RECONFIG,/**< Log event QPLL1 reconfig. */
+    XHDMIPHY1_LOG_EVT_PLL0_EN,       /**< Log event PLL0 reset. */
+    XHDMIPHY1_LOG_EVT_PLL0_RST,      /**< Log event PLL0 reset. */
+    XHDMIPHY1_LOG_EVT_PLL1_EN,       /**< Log event PLL1 reset. */
+    XHDMIPHY1_LOG_EVT_PLL1_RST,      /**< Log event PLL1 reset. */
+    XHDMIPHY1_LOG_EVT_CPLL_EN,       /**< Log event CPLL reset. */
+    XHDMIPHY1_LOG_EVT_CPLL_RST,      /**< Log event CPLL reset. */
+    XHDMIPHY1_LOG_EVT_CPLL_LOCK,     /**< Log event CPLL lock. */
+    XHDMIPHY1_LOG_EVT_CPLL_RECONFIG, /**< Log event CPLL reconfig. */
+    XHDMIPHY1_LOG_EVT_LCPLL_LOCK,    /**< Log event LCPLL lock. */
+    XHDMIPHY1_LOG_EVT_RPLL_LOCK,     /**< Log event RPLL lock. */
+    XHDMIPHY1_LOG_EVT_TXPLL_EN,      /**< Log event TXPLL enable. */
+    XHDMIPHY1_LOG_EVT_TXPLL_RST,     /**< Log event TXPLL reset. */
+    XHDMIPHY1_LOG_EVT_RXPLL_EN,      /**< Log event RXPLL enable. */
+    XHDMIPHY1_LOG_EVT_RXPLL_RST,     /**< Log event RXPLL reset. */
+    XHDMIPHY1_LOG_EVT_GTRX_RST,      /**< Log event GT RX reset. */
+    XHDMIPHY1_LOG_EVT_GTTX_RST,      /**< Log event GT TX reset. */
+    XHDMIPHY1_LOG_EVT_VID_TX_RST,    /**< Log event Vid TX reset. */
+    XHDMIPHY1_LOG_EVT_VID_RX_RST,    /**< Log event Vid RX reset. */
+    XHDMIPHY1_LOG_EVT_TX_ALIGN,      /**< Log event TX align. */
+    XHDMIPHY1_LOG_EVT_TX_ALIGN_TMOUT,/**< Log event TX align Timeout. */
+    XHDMIPHY1_LOG_EVT_TX_TMR,        /**< Log event TX timer. */
+    XHDMIPHY1_LOG_EVT_RX_TMR,        /**< Log event RX timer. */
+    XHDMIPHY1_LOG_EVT_GT_RECONFIG,   /**< Log event GT reconfig. */
+    XHDMIPHY1_LOG_EVT_GT_TX_RECONFIG,/**< Log event GT reconfig. */
+    XHDMIPHY1_LOG_EVT_GT_RX_RECONFIG,/**< Log event GT reconfig. */
+    XHDMIPHY1_LOG_EVT_INIT,          /**< Log event init. */
+    XHDMIPHY1_LOG_EVT_TXPLL_RECONFIG,/**< Log event TXPLL reconfig. */
+    XHDMIPHY1_LOG_EVT_RXPLL_RECONFIG,/**< Log event RXPLL reconfig. */
+    XHDMIPHY1_LOG_EVT_RXPLL_LOCK,    /**< Log event RXPLL lock. */
+    XHDMIPHY1_LOG_EVT_TXPLL_LOCK,    /**< Log event TXPLL lock. */
+    XHDMIPHY1_LOG_EVT_TX_RST_DONE,   /**< Log event TX reset done. */
+    XHDMIPHY1_LOG_EVT_RX_RST_DONE,   /**< Log event RX reset done. */
+    XHDMIPHY1_LOG_EVT_TX_FREQ,       /**< Log event TX frequency. */
+    XHDMIPHY1_LOG_EVT_RX_FREQ,       /**< Log event RX frequency. */
+    XHDMIPHY1_LOG_EVT_DRU_EN,        /**< Log event DRU enable/disable. */
+	XHDMIPHY1_LOG_EVT_TXGPO_RE,     /**< Log event TX GPO Rising Edge. */
+	XHDMIPHY1_LOG_EVT_RXGPO_RE,     /**< Log event RX GPO Rising Edge. */
+    XHDMIPHY1_LOG_EVT_FRL_RECONFIG,  /**< Log event FRL TX Reconfig. */
+    XHDMIPHY1_LOG_EVT_TMDS_RECONFIG, /**< Log event TMDS TX Reconfig. */
+    XHDMIPHY1_LOG_EVT_1PPC_ERR,      /**< Log event 1 PPC Error. */
+    XHDMIPHY1_LOG_EVT_PPC_MSMTCH_ERR,/**< Log event PPC MismatchError. */
+    XHDMIPHY1_LOG_EVT_VDCLK_HIGH_ERR,/**< Log evt VidClk > 148.5 MHz. */
+    XHDMIPHY1_LOG_EVT_NO_DRU,        /**< Log evt Vid not supported no DRU. */
+    XHDMIPHY1_LOG_EVT_GT_QPLL_CFG_ERR,/**< Log event QPLL Config not found. */
+    XHDMIPHY1_LOG_EVT_GT_CPLL_CFG_ERR,/**< Log evt LCPLL Config not found. */
+    XHDMIPHY1_LOG_EVT_GT_LCPLL_CFG_ERR,/**< Log evt RPLL Config not found. */
+    XHDMIPHY1_LOG_EVT_GT_RPLL_CFG_ERR,/**< Log event QPLL Config not found. */
+    XHDMIPHY1_LOG_EVT_VD_NOT_SPRTD_ERR,/**< Log evt Vid fmt not supported. */
+    XHDMIPHY1_LOG_EVT_MMCM_ERR,      /**< Log event MMCM Config not found. */
+    XHDMIPHY1_LOG_EVT_HDMI20_ERR,    /**< Log event HDMI2.0 not supported. */
+    XHDMIPHY1_LOG_EVT_NO_QPLL_ERR,   /**< Log event QPLL not present. */
+    XHDMIPHY1_LOG_EVT_DRU_CLK_ERR,   /**< Log event DRU clk wrong freq. */
+    XHDMIPHY1_LOG_EVT_USRCLK_ERR,    /**< Log event usrclk > 297 MHz. */
+    XHDMIPHY1_LOG_EVT_SPDGRDE_ERR,   /**< Log event Speed Grade -1 error. */
+    XHDMIPHY1_LOG_EVT_DUMMY,         /**< Dummy Event should be last */
+} XHdmiphy1_LogEvent;
+#endif
+
+/* This typedef enumerates the different MMCM Dividers */
+typedef enum {
+    XHDMIPHY1_MMCM_CLKFBOUT_MULT_F, /* M */
+    XHDMIPHY1_MMCM_DIVCLK_DIVIDE,   /* D */
+    XHDMIPHY1_MMCM_CLKOUT_DIVIDE    /* On */
+} XHdmiphy1_MmcmDivType;
+
+/* This typedef enumerates the different MMCM CLKINSEL */
+typedef enum {
+	XHDMIPHY1_MMCM_CLKINSEL_CLKIN1 = 1,
+	XHDMIPHY1_MMCM_CLKINSEL_CLKIN2 = 0,
+} XHdmiphy1_MmcmClkinsel;
+
+/* This typedef enumerates the Linerate to TMDS Clock ratio
+ * for HDMI TX TMDS Clock pattern generator. */
+typedef enum {
+    XHDMIPHY1_Patgen_Ratio_10    = 0x1,  /**< LR:Clock Ratio = 10 */
+    XHDMIPHY1_Patgen_Ratio_20    = 0x2,  /**< LR:Clock Ratio = 20 */
+    XHDMIPHY1_Patgen_Ratio_30    = 0x3,  /**< LR:Clock Ratio = 30 */
+    XHDMIPHY1_Patgen_Ratio_40    = 0x4,  /**< LR:Clock Ratio = 40 */
+    XHDMIPHY1_Patgen_Ratio_50    = 0x5,  /**< LR:Clock Ratio = 50 */
+} XHdmiphy1_HdmiTx_Patgen;
+
+/**
+ * This typedef enumerates the available PRBS patterns available
+ * from the
+ */
+typedef enum {
+    XHDMIPHY1_PRBSSEL_STD_MODE       = 0x0, /**< Pattern gen/mon OFF  */
+    XHDMIPHY1_PRBSSEL_PRBS7          = 0x1, /**< PRBS-7  */
+    XHDMIPHY1_PRBSSEL_PRBS9          = 0x2, /**< PRBS-9  */
+    XHDMIPHY1_PRBSSEL_PRBS15         = 0x3, /**< PRBS-15  */
+    XHDMIPHY1_PRBSSEL_PRBS23         = 0x4, /**< PRBS-23  */
+    XHDMIPHY1_PRBSSEL_PRBS31         = 0x5, /**< PRBS-31  */
+    XHDMIPHY1_PRBSSEL_PCIE           = 0x8, /**< PCIE Compliance Pattern  */
+    XHDMIPHY1_PRBSSEL_SQUARE_2UI     = 0x9, /**< Square wave with 2 UI  */
+    XHDMIPHY1_PRBSSEL_SQUARE_16UI    = 0xA, /**< Square wave with 16 UI  */
+} XHdmiphy1_PrbsPattern;
+
+/******************************************************************************/
+/**
+ * Callback type which represents the handler for interrupts.
+ *
+ * @param   InstancePtr is a pointer to the XHdmiphy1 instance.
+ *
+ * @note    None.
+ *
+*******************************************************************************/
+typedef void (*XHdmiphy1_IntrHandler)(void *InstancePtr);
+
+/******************************************************************************/
+/**
+ * Callback type which represents a custom timer wait handler. This is only
+ * used for Microblaze since it doesn't have a native sleep function. To avoid
+ * dependency on a hardware timer, the default wait functionality is
+ * implemented using loop iterations; this isn't too accurate. If a custom
+ * timer handler is used, the user may implement their own wait implementation
+ * using a hardware timer (see example/) for better accuracy.
+ *
+ * @param   InstancePtr is a pointer to the XHdmiphy1 instance.
+ * @param   MicroSeconds is the number of microseconds to be passed to the
+ *      timer function.
+ *
+ * @note    None.
+ *
+*******************************************************************************/
+typedef void (*XHdmiphy1_TimerHandler)(void *InstancePtr, u32 MicroSeconds);
+
+/******************************************************************************/
+/**
+ * Generic callback type.
+ *
+ * @param   CallbackRef is a pointer to the callback reference.
+ *
+ * @note    None.
+ *
+*******************************************************************************/
+typedef void (*XHdmiphy1_Callback)(void *CallbackRef);
+
+/******************************************************************************/
+/**
+ * Generic callback type.
+ *
+ * @param   CallbackRef is a pointer to the callback reference.
+ *
+ * @note    u8 value.
+ *
+*******************************************************************************/
+typedef u64 (*XHdmiphy1_LogCallback)(void *CallbackRef);
+
+/******************************************************************************/
+/**
+ * Error callback type.
+ *
+ * @param   CallbackRef is a pointer to the callback reference.
+ *
+ * @note    None.
+ *
+*******************************************************************************/
+typedef void (*XHdmiphy1_ErrorCallback)(void *CallbackRef);
+/**
+ * This typedef contains configuration information for CPLL/QPLL programming.
+ */
+typedef struct {
+    u8 MRefClkDiv;
+    /* Aliases for N (QPLL) and N1/N2 (CPLL). */
+    union {
+        u8 NFbDivs[2];
+        u8 NFbDiv;
+        struct {
+            u8 N1FbDiv;
+            u8 N2FbDiv;
+        };
+    };
+    u16 Cdr[5];
+    u8 IsLowerBand;
+} XHdmiphy1_PllParam;
+
+/**
+ * This typedef contains configuration information for PLL type and its
+ * reference clock.
+ */
+typedef struct {
+    /* Below members are common between CPLL/QPLL. */
+    u64 LineRateHz;             /**< The line rate for the
+                            channel. */
+    union {
+        XHdmiphy1_PllParam QpllParams;
+        XHdmiphy1_PllParam CpllParams;   /**< Parameters for a CPLL. */
+        XHdmiphy1_PllParam PllParams;
+        u16 LineRateCfg;
+    };
+    union {
+        XHdmiphy1_PllRefClkSelType CpllRefClkSel;
+                        /**< Multiplexer selection for
+                            the reference clock of
+                            the CPLL. */
+        XHdmiphy1_PllRefClkSelType PllRefClkSel;
+    };
+    /* Below members are CPLL specific. */
+    union {
+        struct {
+            u8 RxOutDiv;        /**< Output clock divider D for
+                            the RX datapath. */
+            u8 TxOutDiv;        /**< Output clock divider D for
+                            the TX datapath. */
+        };
+        u8 OutDiv[2];
+    };
+    union {
+        struct {
+            XHdmiphy1_GtState RxState;   /**< Current state of RX GT. */
+            XHdmiphy1_GtState TxState;   /**< Current state of TX GT. */
+        };
+        XHdmiphy1_GtState GtState[2];
+    };
+    union {
+        struct {
+            XHdmiphy1_ProtocolType RxProtocol;
+                        /**< The protocol which the RX
+                            path is used for. */
+            XHdmiphy1_ProtocolType TxProtocol;
+                        /**< The protocol which the TX
+                            path is used for. */
+        };
+        XHdmiphy1_ProtocolType Protocol[2];
+    };
+    union {
+        struct {
+            XHdmiphy1_SysClkDataSelType RxDataRefClkSel;
+                        /**< Multiplexer selection for
+                            the reference clock of
+                            the RX datapath. */
+            XHdmiphy1_SysClkDataSelType TxDataRefClkSel;
+                        /**< Multiplexer selection for
+                            the reference clock of
+                            the TX datapath. */
+        };
+        XHdmiphy1_SysClkDataSelType DataRefClkSel[2];
+    };
+    union {
+        struct {
+            XHdmiphy1_SysClkOutSelType RxOutRefClkSel;
+                        /**< Multiplexer selection for
+                            the reference clock of
+                            the RX output clock. */
+            XHdmiphy1_SysClkOutSelType TxOutRefClkSel;
+                        /**< Multiplexer selection for
+                            the reference clock of
+                            the TX output clock. */
+        };
+        XHdmiphy1_SysClkOutSelType OutRefClkSel[2];
+    };
+    union {
+        struct {
+            XHdmiphy1_OutClkSelType RxOutClkSel;
+                        /**< Multiplexer selection for
+                            which clock to use as
+                            the RX output clock. */
+            XHdmiphy1_OutClkSelType TxOutClkSel;
+                        /**< Multiplexer selection for
+                            which clock to use as
+                            the TX output clock. */
+        };
+        XHdmiphy1_OutClkSelType OutClkSel[2];
+    };
+    union {
+        struct {
+            u8 RxDelayBypass;   /**< Bypasses the delay
+                            alignment block for the
+                            RX output clock. */
+            u8 TxDelayBypass;   /**< Bypasses the delay
+                            alignment block for the
+                            TX output clock. */
+        };
+        u8 DelayBypass;
+    };
+    u8 RxDataWidth;             /**< In bits. */
+    u8 RxIntDataWidth;          /**< In bytes. */
+    u8 TxDataWidth;             /**< In bits. */
+    u8 TxIntDataWidth;          /**< In bytes. */
+} XHdmiphy1_Channel;
+
+/**
+ * This typedef contains configuration information for MMCM programming.
+ */
+typedef struct {
+    u16 DivClkDivide;
+    u16 ClkFbOutMult;
+    u16 ClkFbOutFrac;
+    u16 ClkOut0Div;
+    u16 ClkOut0Frac;
+    u16 ClkOut1Div;
+    u16 ClkOut2Div;
+} XHdmiphy1_Mmcm;
+
+/**
+ * This typedef represents a GT quad.
+ */
+typedef struct {
+    union {
+        struct {
+            XHdmiphy1_Mmcm RxMmcm;   /**< Mixed-mode clock manager
+                            (MMCM) parameters for
+                            RX. */
+            XHdmiphy1_Mmcm TxMmcm;   /**< MMCM parameters for TX. */
+        };
+        XHdmiphy1_Mmcm Mmcm[2];      /**< MMCM parameters. */
+    };
+    union {
+        struct {
+            XHdmiphy1_Channel Ch1;
+            XHdmiphy1_Channel Ch2;
+            XHdmiphy1_Channel Ch3;
+            XHdmiphy1_Channel Ch4;
+            union {
+            	XHdmiphy1_Channel Cmn0;
+            	XHdmiphy1_Channel Lcpll;
+            };
+            union {
+            	XHdmiphy1_Channel Cmn1;
+            	XHdmiphy1_Channel Rpll;
+            };
+        };
+        XHdmiphy1_Channel Plls[6];
+    };
+    union {
+        struct {
+            u32 GtRefClk0Hz;
+            u32 GtRefClk1Hz;
+            u32 GtNorthRefClk0Hz;
+            u32 GtNorthRefClk1Hz;
+            u32 GtSouthRefClk0Hz;
+            u32 GtSouthRefClk1Hz;
+            u32 GtgRefClkHz;
+        };
+        u32 RefClkHz[7];
+    };
+} XHdmiphy1_Quad;
+
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+/**
+ * This typedef contains the logging mechanism for debug.
+ */
+typedef struct {
+    u16 DataBuffer[128];        /**< Log buffer with event data. */
+    u64 TimeRecord[128];        /**< Log time for the event */
+    u8 HeadIndex;           /**< Index of the head entry of the
+                        Event/DataBuffer. */
+    u8 TailIndex;           /**< Index of the tail entry of the
+                        Event/DataBuffer. */
+} XHdmiphy1_Log;
+#endif
+
+/**
+ * This typedef contains the HDMI 2.1 FRL configurations.
+ */
+typedef struct {
+    u8 IsEnabled;       /**< Is HDMI operation is enabled? */
+    u64 LineRate;       /**< Linerate in bps. */
+    u8 NChannels;       /**< No of Channels. */
+} XHdmiphy1_Hdmi21Cfg;
+
+/**
+ * This typedef contains configuration information for the Video PHY core.
+ */
+typedef struct {
+    u16 DeviceId;           /**< Device instance ID. */
+    UINTPTR BaseAddr;       /**< The base address of the core instance. */
+    XHdmiphy1_GtType XcvrType;       /**< HDMIPHY Transceiver Type */
+    u8 TxChannels;          /**< No. of active channels in TX */
+    u8 RxChannels;          /**< No. of active channels in RX */
+    XHdmiphy1_ProtocolType TxProtocol;   /**< Protocol which TX is used for. */
+    XHdmiphy1_ProtocolType RxProtocol;   /**< Protocol which RX is used for. */
+    XHdmiphy1_PllRefClkSelType TxRefClkSel; /**< TX REFCLK selection. */
+    XHdmiphy1_PllRefClkSelType RxRefClkSel; /**< RX REFCLK selection. */
+    XHdmiphy1_PllRefClkSelType TxFrlRefClkSel; /**< TX FRL REFCLK selection. */
+    XHdmiphy1_PllRefClkSelType RxFrlRefClkSel; /**< RX FRL REFCLK selection. */
+    XHdmiphy1_SysClkDataSelType TxSysPllClkSel; /**< TX SYSCLK selection. */
+    XHdmiphy1_SysClkDataSelType RxSysPllClkSel; /**< RX SYSCLK selectino. */
+    u8 DruIsPresent;        /**< A data recovery unit (DRU) exists
+                                 in the design .*/
+    XHdmiphy1_PllRefClkSelType DruRefClkSel; /**< DRU REFCLK selection. */
+    XVidC_PixelsPerClock Ppc;   /**< Number of input pixels per
+                                     clock. */
+    u8 TxBufferBypass;      /**< TX Buffer Bypass is enabled in the
+                                 design. */
+    u8  HdmiFastSwitch;     /**< HDMI fast switching is enabled in the
+                                 design. */
+    u8  TransceiverWidth;   /**< Transceiver Width seeting in the design */
+    u32 ErrIrq;             /**< Error IRQ is enalbed in design */
+    u32 AxiLiteClkFreq;     /**< AXI Lite Clock Frequency in Hz */
+    u32 DrpClkFreq;         /**< DRP Clock Frequency in Hz */
+    u8  UseGtAsTxTmdsClk;   /**< Use 4th GT channel as TX TMDS clock */
+    u8  RxMaxRate;          /**< Max rate of RX */
+    u8  TxMaxRate;          /**< Max rate of TX */
+} XHdmiphy1_Config;
+
+/* Forward declaration. */
+struct XHdmiphy1_GtConfigS;
+
+/**
+ * The XHdmiphy1 driver instance data. The user is required to allocate a
+ * variable of this type for every XHdmiphy1 device in the system. A pointer
+ * to a variable of this type is then passed to the driver API functions.
+ */
+typedef struct {
+    u32 IsReady;                /**< Device is initialized and ready. */
+    XHdmiphy1_Config Config;     /**< Configuration structure for
+                            the Video PHY core. */
+    const struct XHdmiphy1_GtConfigS *GtAdaptor;
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+    XHdmiphy1_Log Log;               /**< A log of events. */
+#endif
+    XHdmiphy1_Quad Quads[2];         /**< The quads available to the
+                            Video PHY core.*/
+    u32 HdmiRxRefClkHz;         /**< HDMI RX refclk. */
+    u32 HdmiTxRefClkHz;         /**< HDMI TX refclk. */
+    u8 HdmiRxTmdsClockRatio;        /**< HDMI TMDS clock ratio. */
+    u8 HdmiTxSampleRate;            /**< HDMI TX sample rate. */
+    u8 HdmiRxDruIsEnabled;          /**< The DRU is enabled. */
+    u8 HdmiIsQpllPresent;           /**< QPLL is present in HW */
+    XHdmiphy1_Hdmi21Cfg TxHdmi21Cfg; /**< TX HDMI Config */
+    XHdmiphy1_Hdmi21Cfg RxHdmi21Cfg; /**< TX HDMI Config */
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    XHdmiphy1_IntrHandler IntrCpllLockHandler; /**< Callback function for CPLL
+                            lock interrupts. */
+    void *IntrCpllLockCallbackRef;      /**< A pointer to the user data
+                            passed to the CPLL lock
+                            callback function. */
+    XHdmiphy1_IntrHandler IntrQpllLockHandler; /**< Callback function for QPLL
+                            lock interrupts. */
+    void *IntrQpllLockCallbackRef;      /**< A pointer to the user data
+                            passed to the QPLL lock
+                            callback function. */
+    XHdmiphy1_IntrHandler IntrQpll1LockHandler; /**< Callback function for QPLL
+                            lock interrupts. */
+    void *IntrQpll1LockCallbackRef;     /**< A pointer to the user data
+                            passed to the QPLL lock
+                            callback function. */
+    XHdmiphy1_IntrHandler IntrTxAlignDoneHandler; /**< Callback function for TX
+                            align done lock
+                            interrupts. */
+    void *IntrTxAlignDoneCallbackRef;   /**< A pointer to the user data
+                            passed to the TX align
+                            done lock callback
+                            function. */
+#else
+    XHdmiphy1_IntrHandler IntrLcpllLockHandler; /**< Callback function for
+                            LCPLL lock interrupts. */
+    void *IntrLcpllLockCallbackRef;      /**< A pointer to the user data
+                            passed to the LCPLL lock callback function. */
+    XHdmiphy1_IntrHandler IntrRpllLockHandler;   /**< Callback function for
+                            RPLL lock interrupts. */
+    void *IntrRpllLockCallbackRef;      /**< A pointer to the user data
+                            passed to the RPLL lock callback function. */
+    XHdmiphy1_IntrHandler IntrTxGpoRisingEdgeHandler;   /**< Callback function
+    						for TX GPO [3:0] Rising Edge. */
+    void *IntrTxGpoRisingEdgeCallbackRef;      /**< A pointer to the user data
+                            passed to the TX GPO [3:0] Rising Edge
+                            callback function. */
+    XHdmiphy1_IntrHandler IntrRxGpoRisingEdgeHandler;   /**< Callback function
+    						for RX GPO [7:4] Rising Edge. */
+    void *IntrRxGpoRisingEdgeCallbackRef;      /**< A pointer to the user data
+                            passed to the RX GPO [7:4] Rising Edge
+                            callback function. */
+#endif
+    XHdmiphy1_IntrHandler IntrTxResetDoneHandler; /**< Callback function for TX
+                            reset done lock
+                            interrupts. */
+    void *IntrTxResetDoneCallbackRef;   /**< A pointer to the user data
+                            passed to the TX reset
+                            done lock callback
+                            function. */
+    XHdmiphy1_IntrHandler IntrRxResetDoneHandler; /**< Callback function for RX
+                            reset done lock
+                            interrupts. */
+    void *IntrRxResetDoneCallbackRef;   /**< A pointer to the user data
+                            passed to the RX reset
+                            done lock callback
+                            function. */
+    XHdmiphy1_IntrHandler IntrTxClkDetFreqChangeHandler; /**< Callback function
+                            for TX clock detector
+                            frequency change
+                            interrupts. */
+    void *IntrTxClkDetFreqChangeCallbackRef; /**< A pointer to the user data
+                            passed to the TX clock
+                            detector frequency
+                            change callback
+                            function. */
+    XHdmiphy1_IntrHandler IntrRxClkDetFreqChangeHandler; /**< Callback function
+                            for RX clock detector
+                            frequency change
+                            interrupts. */
+    void *IntrRxClkDetFreqChangeCallbackRef; /**< A pointer to the user data
+                            passed to the RX clock
+                            detector frequency
+                            change callback
+                            function. */
+    XHdmiphy1_IntrHandler IntrTxMmcmLockHandler; /**< Callback function
+                            for TX MMCM lock
+                            interrupts. */
+    void *IntrTxMmcmLockCallbackRef; /**< A pointer to the user data
+                            passed to the TX MMCM lock
+                            callback function. */
+    XHdmiphy1_IntrHandler IntrRxMmcmLockHandler; /**< Callback function
+                            for RX MMCM lock
+                            interrupts. */
+    void *IntrRxMmcmLockCallbackRef; /**< A pointer to the user data
+                            passed to the RX MMCM lock
+                            callback function. */
+    XHdmiphy1_IntrHandler IntrTxTmrTimeoutHandler; /**< Callback function for
+                            TX timer timeout interrupts. */
+    void *IntrTxTmrTimeoutCallbackRef;  /**< A pointer to the user data
+                            passed to the TX timer
+                            timeout callback
+                            function. */
+    XHdmiphy1_IntrHandler IntrRxTmrTimeoutHandler; /**< Callback function for
+                            RX timer timeout interrupts. */
+    void *IntrRxTmrTimeoutCallbackRef;  /**< A pointer to the user data
+                            passed to the RX timer timeout
+                            callback function. */
+        /* Error Condition callbacks. */
+    XHdmiphy1_ErrorCallback ErrorCallback; /**< Callback for Error Condition.*/
+    void *ErrorRef;         /**< To be passed to the Error condition
+                             callback. */
+    XHdmiphy1_ErrorCallback PllLayoutErrorCallback;  /**< Callback for Error
+                            Condition. */
+    void *PllLayoutErrorRef;/**< To be passed to the Error condition
+                             callback. */
+        /* HDMI callbacks. */
+    XHdmiphy1_Callback HdmiTxInitCallback;   /**< Callback for TX init. */
+    void *HdmiTxInitRef;            /**< To be passed to the TX init
+                            callback. */
+    XHdmiphy1_Callback HdmiTxReadyCallback;  /**< Callback for TX ready. */
+    void *HdmiTxReadyRef;           /**< To be passed to the TX
+                            ready callback. */
+    XHdmiphy1_Callback HdmiRxInitCallback;   /**< Callback for RX init. */
+    void *HdmiRxInitRef;            /**< To be passed to the RX
+                            init callback. */
+    XHdmiphy1_Callback HdmiRxReadyCallback;  /**< Callback for RX ready. */
+    void *HdmiRxReadyRef;           /**< To be passed to the RX
+                            ready callback. */
+    XHdmiphy1_LogCallback LogWriteCallback; /**< Callback for log write */
+    u32 *LogWriteRef;  /**< To be passed to the log write callback */
+    XHdmiphy1_TimerHandler UserTimerWaitUs;  /**< Custom user function for
+                            delay/sleep. */
+    void *UserTimerPtr;         /**< Pointer to a timer instance
+                            used by the custom user
+                            delay/sleep function. */
+} XHdmiphy1;
+
+/**************************** Function Prototypes *****************************/
+
+/* xhdmiphy1.c: Setup and initialization functions. */
+void XHdmiphy1_CfgInitialize(XHdmiphy1 *InstancePtr,
+		XHdmiphy1_Config *ConfigPtr,
+        UINTPTR EffectiveAddr);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+u32 XHdmiphy1_PllInitialize(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId,
+        XHdmiphy1_PllRefClkSelType QpllRefClkSel,
+        XHdmiphy1_PllRefClkSelType CpllxRefClkSel,
+        XHdmiphy1_PllType TxPllSelect, XHdmiphy1_PllType RxPllSelect);
+#endif
+u32 XHdmiphy1_GetVersion(XHdmiphy1 *InstancePtr);
+void XHdmiphy1_WaitUs(XHdmiphy1 *InstancePtr, u32 MicroSeconds);
+void XHdmiphy1_SetUserTimerHandler(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_TimerHandler CallbackFunc, void *CallbackRef);
+
+/* xhdmiphy1.c: Channel configuration functions - setters. */
+u32 XHdmiphy1_CfgLineRate(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u64 LineRateHz);
+
+/* xhdmiphy1.c: Channel configuration functions - getters. */
+XHdmiphy1_PllType XHdmiphy1_GetPllType(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, XHdmiphy1_ChannelId ChId);
+u64 XHdmiphy1_GetLineRateHz(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+
+/* xhdmiphy1.c: Reset functions. */
+u32 XHdmiphy1_ResetGtPll(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Hold);
+u32 XHdmiphy1_ResetGtTxRx(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Hold);
+
+/* xhdmiphy1.c: TX|RX Control functions. */
+u32 XHdmiphy1_SetPolarity(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Polarity);
+u32 XHdmiphy1_SetPrbsSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        XHdmiphy1_PrbsPattern Pattern);
+u32 XHdmiphy1_TxPrbsForceError(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 ForceErr);
+void XHdmiphy1_SetTxVoltageSwing(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Vs);
+void XHdmiphy1_SetTxPreEmphasis(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Pe);
+void XHdmiphy1_SetTxPostCursor(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Pc);
+void XHdmiphy1_SetRxLpm(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Enable);
+
+/* xhdmiphy1.c: GT/MMCM DRP access. */
+u32 XHdmiphy1_DrpWr(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u16 Addr, u16 Val);
+u16 XHdmiphy1_DrpRd(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u16 Addr, u16 *RetVal);
+void XHdmiphy1_MmcmPowerDown(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u8 Hold);
+void XHdmiphy1_MmcmStart(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_IBufDsEnable(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u8 Enable);
+void XHdmiphy1_Clkout1OBufTdsEnable(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir, u8 Enable);
+
+/* xhdmiphy1.c: Error Condition. */
+void XHdmiphy1_SetErrorCallback(XHdmiphy1 *InstancePtr,
+        void *CallbackFunc, void *CallbackRef);
+
+/* xhdmiphy1_log.c: Logging functions. */
+void XHdmiphy1_SetLogCallback(XHdmiphy1 *InstancePtr,
+        u64 *CallbackFunc, void *CallbackRef);
+int XHdmiphy1_LogShow(XHdmiphy1 *InstancePtr, char *buff, int buff_size);
+void XHdmiphy1_LogReset(XHdmiphy1 *InstancePtr);
+u16 XHdmiphy1_LogRead(XHdmiphy1 *InstancePtr);
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+void XHdmiphy1_LogWrite(XHdmiphy1 *InstancePtr, XHdmiphy1_LogEvent Evt,
+		u8 Data);
+#else
+#define XHdmiphy1_LogWrite(...)
+#endif
+
+/* xhdmiphy1_intr.c: Interrupt handling functions. */
+void XHdmiphy1_InterruptHandler(XHdmiphy1 *InstancePtr);
+
+/* xhdmiphy1_selftest.c: Self test function. */
+u32 XHdmiphy1_SelfTest(XHdmiphy1 *InstancePtr);
+
+/* xhdmiphy1_sinit.c: Configuration extraction function. */
+XHdmiphy1_Config *XHdmiphy1_LookupConfig(u16 DeviceId);
+
+/* xhdmiphy1_hdmi.c, xhdmiphy1_hdmi_intr.c: Protocol specific functions. */
+u32 XHdmiphy1_Hdmi_CfgInitialize(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_Config *CfgPtr);
+u32 XHdmiphy1_SetHdmiTxParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId,
+        XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc,
+        XVidC_ColorFormat ColorFormat);
+u32 XHdmiphy1_SetHdmiRxParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+
+u32 XHdmiphy1_HdmiCfgCalcMmcmParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+void XHdmiphy1_HdmiUpdateClockSelection(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_SysClkDataSelType TxSysPllClkSel,
+        XHdmiphy1_SysClkDataSelType RxSysPllClkSel);
+#endif
+void XHdmiphy1_ClkDetFreqReset(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir);
+u32 XHdmiphy1_ClkDetGetRefClkFreqHz(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir);
+u32 XHdmiphy1_DruGetRefClkFreqHz(XHdmiphy1 *InstancePtr);
+int XHdmiphy1_HdmiDebugInfo(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, char *buff, int buff_size);
+void XHdmiphy1_SetHdmiCallback(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_HdmiHandlerType HandlerType,
+        void *CallbackFunc, void *CallbackRef);
+u32 XHdmiphy1_Hdmi20Config(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir);
+u32 XHdmiphy1_Hdmi21Config(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir,
+        u64 LineRate, u8 NChannels);
+void XHdmiphy1_RegisterDebug(XHdmiphy1 *InstancePtr);
+void XHdmiphy1_TxPllreset(XHdmiphy1 *InstancePtr);
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+#define XHDMIPHY1_CH2IDX(Id) ((Id) - XHDMIPHY1_CHANNEL_ID_CH1)
+#define XHDMIPHY1_ISCH(Id)       (((Id) == XHDMIPHY1_CHANNEL_ID_CHA) || \
+	((XHDMIPHY1_CHANNEL_ID_CH1 <= (Id)) && ((Id) <= XHDMIPHY1_CHANNEL_ID_CH4)))
+#define XHDMIPHY1_ISCMN(Id)      (((Id) == XHDMIPHY1_CHANNEL_ID_CMNA) || \
+  ((XHDMIPHY1_CHANNEL_ID_CMN0 <= (Id)) && ((Id) <= XHDMIPHY1_CHANNEL_ID_CMN1)))
+#define XHDMIPHY1_ISTXMMCM(Id)   ((Id) == XHDMIPHY1_CHANNEL_ID_TXMMCM)
+#define XHDMIPHY1_ISRXMMCM(Id)   ((Id) == XHDMIPHY1_CHANNEL_ID_RXMMCM)
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+#define XHdmiphy1_IsTxUsingQpll(InstancePtr, QuadId, ChId) \
+        ((XHDMIPHY1_PLL_TYPE_QPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, ChId)) || \
+        (XHDMIPHY1_PLL_TYPE_QPLL0 == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, ChId)) || \
+        (XHDMIPHY1_PLL_TYPE_QPLL1 == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, ChId)))
+#define XHdmiphy1_IsRxUsingQpll(InstancePtr, QuadId, ChId) \
+        ((XHDMIPHY1_PLL_TYPE_QPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, ChId)) || \
+        (XHDMIPHY1_PLL_TYPE_QPLL0 == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, ChId)) || \
+        (XHDMIPHY1_PLL_TYPE_QPLL1 == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, ChId)))
+#define XHdmiphy1_IsTxUsingCpll(InstancePtr, QuadId, ChId) \
+        (XHDMIPHY1_PLL_TYPE_CPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, ChId))
+#define XHdmiphy1_IsRxUsingCpll(InstancePtr, QuadId, ChId) \
+        (XHDMIPHY1_PLL_TYPE_CPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, ChId))
+#else
+#define XHdmiphy1_IsTxUsingLcpll(InstancePtr, QuadId, ChId) \
+        (XHDMIPHY1_PLL_TYPE_LCPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, ChId))
+#define XHdmiphy1_IsRxUsingLcpll(InstancePtr, QuadId, ChId) \
+        (XHDMIPHY1_PLL_TYPE_LCPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, ChId))
+#define XHdmiphy1_IsTxUsingRpll(InstancePtr, QuadId, ChId) \
+        (XHDMIPHY1_PLL_TYPE_RPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, ChId))
+#define XHdmiphy1_IsRxUsingRpll(InstancePtr, QuadId, ChId) \
+        (XHDMIPHY1_PLL_TYPE_RPLL == \
+        XHdmiphy1_GetPllType(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, ChId))
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDMIPHY1_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_gt.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_gt.h
@@ -0,0 +1,126 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_gt.h
+ *
+ * The Xilinx HDMI PHY (HDMIPHY) driver. This driver supports the 
+ * Xilinx HDMI PHY IP core.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * 1.1   ku   17/05/20 Adding uniquification to avoid clash with vphy
+ * </pre>
+ *
+ * @addtogroup xhdmiphy1_v2_2
+ * @{
+*******************************************************************************/
+
+#ifndef XHDMIPHY1_GT_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XHDMIPHY1_GT_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+#include "xil_assert.h"
+
+/****************************** Type Definitions ******************************/
+
+typedef struct {
+	const u8 *M;
+	const u8 *N1;
+	const u8 *N2;
+	const u8 *D;
+} XHdmiphy1_GtPllDivs;
+
+typedef struct XHdmiphy1_GtConfigS {
+	u32 (*CfgSetCdr)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId);
+	u32 (*CheckPllOpRange)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId, u64);
+	u32 (*OutDivChReconfig)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId,
+			XHdmiphy1_DirectionType);
+	u32 (*ClkChReconfig)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId);
+	u32 (*ClkCmnReconfig)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId);
+	u32 (*RxChReconfig)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId);
+	u32 (*TxChReconfig)(XHdmiphy1 *, u8, XHdmiphy1_ChannelId);
+
+	XHdmiphy1_GtPllDivs CpllDivs;
+	XHdmiphy1_GtPllDivs QpllDivs;
+} XHdmiphy1_GtConfig;
+
+/******************* Macros (Inline Functions) Definitions ********************/
+#ifdef __cplusplus
+u32 XHdmiphy1_CfgSetCdr(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_CheckPllOpRange(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, u64 PllClkOutFreqHz);
+u32 XHdmiphy1_OutDivChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+u32 XHdmiphy1_ClkChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_ClkCmnReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_RxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_TxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+#else
+#define XHdmiphy1_CfgSetCdr(Ip, ...) \
+		((Ip)->GtAdaptor->CfgSetCdr(Ip, __VA_ARGS__))
+#define XHdmiphy1_CheckPllOpRange(Ip, ...) \
+		((Ip)->GtAdaptor->CheckPllOpRange(Ip, __VA_ARGS__))
+#define XHdmiphy1_OutDivChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->OutDivChReconfig(Ip, __VA_ARGS__))
+#define XHdmiphy1_ClkChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->ClkChReconfig(Ip, __VA_ARGS__))
+#define XHdmiphy1_ClkCmnReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->ClkCmnReconfig(Ip, __VA_ARGS__))
+#define XHdmiphy1_RxChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->RxChReconfig(Ip, __VA_ARGS__))
+#define XHdmiphy1_TxChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->TxChReconfig(Ip, __VA_ARGS__))
+#endif
+
+/*************************** Variable Declarations ****************************/
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+extern const XHdmiphy1_GtConfig XHdmiphy1_Gthe4Config;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+extern const XHdmiphy1_GtConfig XHdmiphy1_Gtye4Config;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+extern const XHdmiphy1_GtConfig Gtye5Config;
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDMIPHY1_GT_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_gtye5.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_gtye5.c
@@ -0,0 +1,620 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_gtye4.c
+ *
+ * Contains a minimal set of functions for the XHdmiphy1 driver that allow
+ * access to all of the Video PHY core's functionality. See xhdmiphy1.h for a
+ * detailed description of the driver.
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xhdmiphy1_gt.h"
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+#include "xstatus.h"
+
+/**************************** Function Prototypes *****************************/
+
+u32 XHdmiphy1_Gtye5RxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_Gtye5TxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+
+/************************** Constant Definitions ******************************/
+/* PLL operating ranges. */
+#define XHDMIPHY1_LCPLL_MIN        		8000000000LL
+#define XHDMIPHY1_LCPLL_MAX        		16375000000LL
+#define XHDMIPHY1_LCPLL_MIN_REFCLK 		120000000LL
+#define XHDMIPHY1_RPLL_MIN         		4000000000LL
+#define XHDMIPHY1_RPLL_MAX         		8000000000LL
+#define XHDMIPHY1_RPLL_MIN_REFCLK  		120000000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_LRATE  3000000000U
+
+
+const XHdmiphy1_GtConfig Gtye5Config = {
+/*  .CfgSetCdr = XHdmiphy1_Gtye4CfgSetCdr,
+    .CheckPllOpRange = XHdmiphy1_Gtye4CheckPllOpRange,
+    .OutDivChReconfig = XHdmiphy1_Gtye4OutDivChReconfig,
+    .ClkChReconfig = XHdmiphy1_Gtye4ClkChReconfig,
+    .ClkCmnReconfig = XHdmiphy1_Gtye4ClkCmnReconfig, */
+    .RxChReconfig = XHdmiphy1_Gtye5RxChReconfig,
+    .TxChReconfig = XHdmiphy1_Gtye5TxChReconfig,
+
+    .CpllDivs = {
+        .M = 0,
+        .N1 = 0,
+        .N2 = 0,
+        .D = 0,
+    },
+    .QpllDivs = {
+        .M = 0,
+        .N1 = 0,
+        .N2 = 0,
+        .D = 0,
+    },
+};
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function calculates the LCPLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if calculated LCPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiLcpllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 Status = XST_SUCCESS;
+	u32 *RefClkPtr;
+	u8 TmdsClockRatio = 0;
+	u8 IsHdmi21 = 0;
+	u64 LineRate = 0;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+
+	/* Pre-calculation. */
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		RefClkPtr = &InstancePtr->HdmiRxRefClkHz;
+		IsHdmi21 = InstancePtr->RxHdmi21Cfg.IsEnabled;
+		TmdsClockRatio = InstancePtr->HdmiRxTmdsClockRatio;
+
+		/* Calculate Line Rate */
+		if (IsHdmi21) {
+			LineRate = InstancePtr->RxHdmi21Cfg.LineRate;
+		}
+		else {
+			LineRate = (u64)(*RefClkPtr) * ((TmdsClockRatio ? 40 : 10));
+		}
+
+		/* Disable DRU */
+		InstancePtr->HdmiRxDruIsEnabled = 0;
+
+		/* Enable DRU based on incoming REFCLK */
+		if ((!IsHdmi21) && (!TmdsClockRatio) &&
+			(InstancePtr->HdmiRxRefClkHz < XHDMIPHY1_LCPLL_MIN_REFCLK)) {
+			if (InstancePtr->Config.DruIsPresent) {
+	            /* Check DRU frequency */
+				if (XHdmiphy1_DruGetRefClkFreqHz(InstancePtr) == XST_FAILURE) {
+					XHdmiphy1_LogWrite(InstancePtr,
+							XHDMIPHY1_LOG_EVT_DRU_CLK_ERR, 1);
+					XHdmiphy1_ErrorHandler(InstancePtr);
+					return (XST_FAILURE);
+				}
+
+				InstancePtr->HdmiRxDruIsEnabled = 1;
+				LineRate = XHDMIPHY1_HDMI_GTYE5_DRU_LRATE;
+			}
+			else {
+				XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_NO_DRU, 1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+		}
+	}
+	else {
+		RefClkPtr = &InstancePtr->HdmiTxRefClkHz;
+		IsHdmi21 = InstancePtr->TxHdmi21Cfg.IsEnabled;
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		if (!IsHdmi21) {
+			/* Determine if HDMI 2.0 Mode */
+			if (*RefClkPtr >= 340000000) {
+				TmdsClockRatio = 1;
+				(*RefClkPtr) = (*RefClkPtr) / 4;
+			}
+			/* Check for x1 Over Sampling Mode*/
+			else if (*RefClkPtr >= 124990000) {
+				InstancePtr->HdmiTxSampleRate = 1;
+			}
+			/* Check for x2 Over Sampling Mode*/
+			else if (*RefClkPtr >= 99000000) {
+				InstancePtr->HdmiTxSampleRate = 2;
+				(*RefClkPtr) = (*RefClkPtr) * 2;
+			}
+			/* Check for x3 Over Sampling Mode*/
+			else if (*RefClkPtr >= 59400000) {
+				InstancePtr->HdmiTxSampleRate = 3;
+				(*RefClkPtr) = (*RefClkPtr) * 3;
+			}
+			/* Check for x5 Over Sampling Mode*/
+			else if (*RefClkPtr < 59400000) {
+				InstancePtr->HdmiTxSampleRate = 5;
+				(*RefClkPtr) = (*RefClkPtr) * 5;
+			}
+		}
+
+		/* Calculate Line Rate */
+		if (IsHdmi21) {
+			LineRate = InstancePtr->TxHdmi21Cfg.LineRate;
+		}
+		else {
+			LineRate = (u64)(*RefClkPtr) * ((TmdsClockRatio ? 40 : 10));
+		}
+
+	}
+
+	/* Check for DRU mode */
+	if ((Dir == XHDMIPHY1_DIR_RX) &&
+		(InstancePtr->HdmiRxDruIsEnabled)) {
+		InstancePtr->Quads[0].Lcpll.LineRateCfg = 0;
+	}
+	/* Check for HDMI 1.4/2.0 GT LineRate Config */
+	else if (!IsHdmi21) {
+		/* HDMI 1.4 */
+		if (!TmdsClockRatio) {
+			if ((119990000 <= (*RefClkPtr)) &&
+					((*RefClkPtr) <= 204687500)) {
+				InstancePtr->Quads[0].Lcpll.LineRateCfg = 1;
+			}
+			else if ((204687500 <= (*RefClkPtr)) &&
+						/* 297 MHz + 0.5% + 10 KHz error */
+						((*RefClkPtr) <= 298500000)) {
+				InstancePtr->Quads[0].Lcpll.LineRateCfg = 2;
+			}
+			else{
+				Status = XST_FAILURE;
+			}
+		}
+		/* HDMI 2.0 */
+		else {
+			if ((84570000 <= (*RefClkPtr)) &&
+						((*RefClkPtr) <= 102343750)) {
+				InstancePtr->Quads[0].Lcpll.LineRateCfg = 3;
+			}
+			else if ((102343750 <= (*RefClkPtr)) &&
+						((*RefClkPtr) <= 149500000)) {
+				InstancePtr->Quads[0].Lcpll.LineRateCfg = 4;
+			}
+			else{
+				Status = XST_FAILURE;
+			}
+		}
+	}
+	/* Check for HDMI 2.1 GT LineRate Config */
+	else if (IsHdmi21) {
+		if (LineRate == 3000000000) {
+			InstancePtr->Quads[0].Lcpll.LineRateCfg = 5;
+		}
+		else if (LineRate == 6000000000) {
+			InstancePtr->Quads[0].Lcpll.LineRateCfg = 6;
+		}
+		else if (LineRate == 8000000000) {
+			InstancePtr->Quads[0].Lcpll.LineRateCfg = 7;
+		}
+		else if (LineRate == 10000000000) {
+			InstancePtr->Quads[0].Lcpll.LineRateCfg = 8;
+		}
+		else if (LineRate == 12000000000) {
+			InstancePtr->Quads[0].Lcpll.LineRateCfg = 9;
+		}
+		else {
+			Status = XST_FAILURE;
+		}
+	}
+
+	/* Update Line Rate Value */
+	XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+			/* LCPLL is CMN0 */
+			XHDMIPHY1_CHANNEL_ID_CMN0, LineRate);
+
+	if (Status == XST_FAILURE) {
+		XHdmiphy1_LogWrite(InstancePtr,
+				XHDMIPHY1_LOG_EVT_GT_LCPLL_CFG_ERR, 1);
+		XHdmiphy1_ErrorHandler(InstancePtr);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the RPLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if calculated RPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiRpllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 Status = XST_SUCCESS;
+	u32 *RefClkPtr;
+	u8 TmdsClockRatio = 0;
+	u8 IsHdmi21 = 0;
+	u64 LineRate = 0;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+
+	/* Pre-calculation. */
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		RefClkPtr = &InstancePtr->HdmiRxRefClkHz;
+		IsHdmi21 = InstancePtr->RxHdmi21Cfg.IsEnabled;
+		TmdsClockRatio = InstancePtr->HdmiRxTmdsClockRatio;
+
+		/* Calculate Line Rate */
+		if (IsHdmi21) {
+			LineRate = InstancePtr->RxHdmi21Cfg.LineRate;
+		}
+		else {
+			LineRate = (u64)(*RefClkPtr) * ((TmdsClockRatio ? 40 : 10));
+		}
+
+		/* Disable DRU */
+		InstancePtr->HdmiRxDruIsEnabled = 0;
+
+		/* Enable DRU based on incoming REFCLK */
+		if ((!IsHdmi21) && (!TmdsClockRatio) &&
+			(InstancePtr->HdmiRxRefClkHz < XHDMIPHY1_RPLL_MIN_REFCLK)) {
+			if (InstancePtr->Config.DruIsPresent) {
+	            /* Check DRU frequency */
+				if (XHdmiphy1_DruGetRefClkFreqHz(InstancePtr) == XST_FAILURE) {
+					XHdmiphy1_LogWrite(InstancePtr,
+							XHDMIPHY1_LOG_EVT_DRU_CLK_ERR, 1);
+					XHdmiphy1_ErrorHandler(InstancePtr);
+					return (XST_FAILURE);
+				}
+
+				InstancePtr->HdmiRxDruIsEnabled = 1;
+				LineRate = XHDMIPHY1_HDMI_GTYE5_DRU_LRATE;
+			}
+			else {
+				XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_NO_DRU, 1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+		}
+	}
+	else {
+		RefClkPtr = &InstancePtr->HdmiTxRefClkHz;
+		IsHdmi21 = InstancePtr->TxHdmi21Cfg.IsEnabled;
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		if (!IsHdmi21) {
+			/* Determine if HDMI 2.0 Mode */
+			if (*RefClkPtr >= 340000000) {
+				TmdsClockRatio = 1;
+				(*RefClkPtr) = (*RefClkPtr) / 4;
+			}
+			/* Check for x1 Over Sampling Mode*/
+			else if (*RefClkPtr >= 124990000) {
+				InstancePtr->HdmiTxSampleRate = 1;
+			}
+			/* Check for x2 Over Sampling Mode*/
+			else if (*RefClkPtr >= 99000000) {
+				InstancePtr->HdmiTxSampleRate = 2;
+				(*RefClkPtr) = (*RefClkPtr) * 2;
+			}
+			/* Check for x3 Over Sampling Mode*/
+			else if (*RefClkPtr >= 59400000) {
+				InstancePtr->HdmiTxSampleRate = 3;
+				(*RefClkPtr) = (*RefClkPtr) * 3;
+			}
+			/* Check for x5 Over Sampling Mode*/
+			else if (*RefClkPtr < 59400000) {
+				InstancePtr->HdmiTxSampleRate = 5;
+				(*RefClkPtr) = (*RefClkPtr) * 5;
+			}
+		}
+
+		/* Calculate Line Rate */
+		if (IsHdmi21) {
+			LineRate = InstancePtr->TxHdmi21Cfg.LineRate;
+		}
+		else {
+			LineRate = (u64)(*RefClkPtr) * ((TmdsClockRatio ? 40 : 10));
+		}
+
+	}
+
+	/* Check for DRU mode */
+	if ((Dir == XHDMIPHY1_DIR_RX) &&
+		(InstancePtr->HdmiRxDruIsEnabled)) {
+		InstancePtr->Quads[0].Rpll.LineRateCfg = 0;
+	}
+	/* Check for HDMI 1.4/2.0 GT LineRate Config */
+	else if (!IsHdmi21) {
+		/* HDMI 1.4 */
+		if (!TmdsClockRatio) {
+			if ((119990000 <= (*RefClkPtr)) &&
+					((*RefClkPtr) <= 200000000)) {
+				InstancePtr->Quads[0].Rpll.LineRateCfg = 1;
+			}
+			else if ((200000000 <= (*RefClkPtr)) &&
+						/* 297 MHz + 0.5% + 10 KHz error */
+						((*RefClkPtr) <= 298500000)) {
+				InstancePtr->Quads[0].Rpll.LineRateCfg = 2;
+			}
+			else{
+				Status = XST_FAILURE;
+			}
+		}
+		/* HDMI 2.0 */
+		else {
+			if ((84570000 <= (*RefClkPtr)) &&
+						((*RefClkPtr) <= 100000000)) {
+				InstancePtr->Quads[0].Rpll.LineRateCfg = 3;
+			}
+			else if ((100000000 <= (*RefClkPtr)) &&
+						((*RefClkPtr) <= 149500000)) {
+				InstancePtr->Quads[0].Rpll.LineRateCfg = 4;
+			}
+			else{
+				Status = XST_FAILURE;
+			}
+		}
+	}
+	/* Check for HDMI 2.1 GT LineRate Config */
+	else if (IsHdmi21) {
+		if (LineRate == 3000000000) {
+			InstancePtr->Quads[0].Rpll.LineRateCfg = 5;
+		}
+		else if (LineRate == 6000000000) {
+			InstancePtr->Quads[0].Rpll.LineRateCfg = 6;
+		}
+		else if (LineRate == 8000000000) {
+			InstancePtr->Quads[0].Rpll.LineRateCfg = 7;
+		}
+		else if (LineRate == 10000000000) {
+			InstancePtr->Quads[0].Rpll.LineRateCfg = 8;
+		}
+		else if (LineRate == 12000000000) {
+			InstancePtr->Quads[0].Rpll.LineRateCfg = 9;
+		}
+		else {
+			Status = XST_FAILURE;
+		}
+	}
+
+	/* Update Line Rate Value */
+	XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+			/* RPLL is CMN1 */
+			XHDMIPHY1_CHANNEL_ID_CMN1, LineRate);
+
+	if (Status == XST_FAILURE) {
+		XHdmiphy1_LogWrite(InstancePtr,
+				XHDMIPHY1_LOG_EVT_GT_RPLL_CFG_ERR, 1);
+		XHdmiphy1_ErrorHandler(InstancePtr);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the TX PLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if calculated QPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiTxPllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	u32 Status;
+	XHdmiphy1_PllType PllType;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+        XHDMIPHY1_CHANNEL_ID_CH1);
+
+    if (PllType == XHDMIPHY1_PLL_TYPE_LCPLL) {
+    	Status = XHdmiphy1_HdmiLcpllParam(InstancePtr, 0, ChId,
+    				XHDMIPHY1_DIR_TX);
+    }
+    else { /* RPLL */
+    	Status = XHdmiphy1_HdmiRpllParam(InstancePtr, 0, ChId,
+    				XHDMIPHY1_DIR_TX);
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the RX PLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if calculated QPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiRxPllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+    u32 Status;
+	XHdmiphy1_PllType PllType;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+        XHDMIPHY1_CHANNEL_ID_CH1);
+
+    if (PllType == XHDMIPHY1_PLL_TYPE_LCPLL) {
+    	Status = XHdmiphy1_HdmiLcpllParam(InstancePtr, 0, ChId,
+    				XHDMIPHY1_DIR_RX);
+    }
+    else { /* RPLL */
+    	Status = XHdmiphy1_HdmiRpllParam(InstancePtr, 0, ChId,
+    				XHDMIPHY1_DIR_RX);
+    }
+
+	return Status;
+}
+
+
+/*****************************************************************************/
+/**
+* This function will configure the channel's RX settings.
+*
+* @param    InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param    QuadId is the GT quad ID to operate on.
+* @param    ChId is the channel ID to operate on.
+*
+* @return
+*       - XST_SUCCESS if the configuration was successful.
+*       - XST_FAILURE otherwise.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Gtye5RxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	u8 CfgValComp;
+
+	/* Compare the current and next CFG values */
+	CfgValComp = XHdmiphy1_CheckLineRateCfg(InstancePtr, QuadId, ChId,
+					XHDMIPHY1_DIR_RX);
+
+	if (!CfgValComp) {
+		/* If CFG values are different */
+		XHdmiphy1_SetGtLineRateCfg(InstancePtr, QuadId, ChId,
+					XHDMIPHY1_DIR_RX);
+	}
+	else {
+		/* Toggle RX Master Reset */
+		XHdmiphy1_GtMstReset(InstancePtr, QuadId, ChId, XHDMIPHY1_DIR_RX,
+					TRUE);
+		XHdmiphy1_GtMstReset(InstancePtr, QuadId, ChId, XHDMIPHY1_DIR_RX,
+					FALSE);
+	}
+
+    return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the channel's TX settings.
+*
+* @param    InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param    QuadId is the GT quad ID to operate on.
+* @param    ChId is the channel ID to operate on.
+*
+* @return
+*       - XST_SUCCESS if the configuration was successful.
+*       - XST_FAILURE otherwise.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Gtye5TxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	u8 CfgValComp;
+
+	/* Compare the current and next CFG values */
+	CfgValComp = XHdmiphy1_CheckLineRateCfg(InstancePtr, QuadId, ChId,
+					XHDMIPHY1_DIR_TX);
+
+	if (!CfgValComp) {
+		/* If CFG values are different */
+		XHdmiphy1_SetGtLineRateCfg(InstancePtr, QuadId, ChId,
+					XHDMIPHY1_DIR_TX);
+	}
+	else {
+		/* Toggle RX Master Reset */
+		XHdmiphy1_GtMstReset(InstancePtr, QuadId, ChId, XHDMIPHY1_DIR_TX,
+					TRUE);
+		XHdmiphy1_GtMstReset(InstancePtr, QuadId, ChId, XHDMIPHY1_DIR_TX,
+					FALSE);
+	}
+
+    return XST_SUCCESS;
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hdmi.c
@@ -0,0 +1,2931 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_hdmi.c
+ *
+ * This file contains video PHY functionality specific to the HDMI protocol.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * 1.1   ku   24/07/20 Program MMCM params based on max line rate
+ *                     configured in IP GUI
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xstatus.h"
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+#include "xhdmiphy1_hdmi.h"
+
+/****************************** Type Definitions ******************************/
+
+typedef struct {
+	u64 DruLineRate;
+	u16 PllScale;
+	u32 Qpll0RefClkMin;
+	u32 Qpll1RefClkMin;
+	u32 CpllRefClkMin;
+	u16 TxMmcmScale;
+	u64 TxMmcmFvcoMin;
+	u64 TxMmcmFvcoMax;
+	u16 RxMmcmScale;
+	u64 RxMmcmFvcoMin;
+	u64 RxMmcmFvcoMax;
+} XHdmiphy1_GtHdmiChars;
+
+/**************************** Function Prototypes *****************************/
+
+extern void XHdmiphy1_Ch2Ids(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+		u8 *Id0, u8 *Id1);
+static const XHdmiphy1_GtHdmiChars *GetGtHdmiPtr(XHdmiphy1 *InstancePtr);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+static void XHdmiphy1_HdmiSetSystemClockSelection(XHdmiphy1 *InstancePtr,
+                u8 QuadId);
+#endif
+static void XHdmiphy1_MmcmParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir);
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function initializes the Video PHY for HDMI.
+ *
+ * @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+ * @param	CfgPtr is a pointer to the configuration structure that will
+ *		        be used to copy the settings from.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u32 XHdmiphy1_Hdmi_CfgInitialize(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_Config *CfgPtr)
+{
+	u8 Id, Id0, Id1;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+
+	/* Init done. */
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_INIT, 0);
+
+	/* Setup the instance. */
+	XHdmiphy1_CfgInitialize(InstancePtr, CfgPtr, CfgPtr->BaseAddr);
+
+	/* Set default. */
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+			XHDMIPHY1_GT_STATE_IDLE;
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+			XHDMIPHY1_GT_STATE_IDLE;
+		/* Initialize Transceiver Width values */
+		if (InstancePtr->Config.TransceiverWidth == 2) {
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				TxDataWidth = 20;
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				TxIntDataWidth = 2;
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				RxDataWidth = 20;
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				RxIntDataWidth = 2;
+		}
+		else {
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				TxDataWidth = 40;
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				TxIntDataWidth = 4;
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				RxDataWidth = 40;
+			InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+				RxIntDataWidth = 4;
+		}
+	}
+
+	/* Interrupt Disable. */
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_CPLL_LOCK);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_QPLL0_LOCK);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TXALIGN_DONE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_QPLL1_LOCK);
+#else
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE);
+#endif
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT);
+	XHdmiphy1_IntrDisable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+
+	/* Setup HDMI interrupt handler callback*/
+	XHdmiphy1_HdmiIntrHandlerCallbackInit(InstancePtr);
+
+	/* Configure clock detector. */
+	XHdmiphy1_ClkDetEnable(InstancePtr, FALSE);
+	XHdmiphy1_ClkDetSetFreqTimeout(InstancePtr,
+                InstancePtr->Config.AxiLiteClkFreq);
+	XHdmiphy1_ClkDetSetFreqLockThreshold(InstancePtr, 40);
+
+	/* Start capturing logs. */
+	XHdmiphy1_LogReset(InstancePtr);
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_INIT, 0);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_HdmiSetSystemClockSelection(InstancePtr, QuadId);
+
+	/* Indicate of QPLL is present in design */
+	if ((XHdmiphy1_IsTxUsingQpll(InstancePtr,
+			QuadId, XHDMIPHY1_CHANNEL_ID_CH1) &&
+			(XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX))) ||
+		(XHdmiphy1_IsRxUsingQpll(InstancePtr,
+				QuadId, XHDMIPHY1_CHANNEL_ID_CH1) &&
+			(XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)))) {
+		InstancePtr->HdmiIsQpllPresent = TRUE;
+	} else {
+		InstancePtr->HdmiIsQpllPresent = FALSE;
+	}
+
+	if ((InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTHE4) ||
+	    (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTYE4)) {
+		XHdmiphy1_SetBufgGtDiv(InstancePtr, XHDMIPHY1_DIR_TX, 1);
+		XHdmiphy1_SetBufgGtDiv(InstancePtr, XHDMIPHY1_DIR_RX, 1);
+	}
+    XHdmiphy1_PowerDownGtPll(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CMNA,
+            TRUE);
+    XHdmiphy1_PowerDownGtPll(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CHA,
+            TRUE);
+	XHdmiphy1_ResetGtPll(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CHA,
+			XHDMIPHY1_DIR_RX, TRUE);
+	XHdmiphy1_ResetGtPll(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CHA,
+			XHDMIPHY1_DIR_TX, TRUE);
+#endif
+	XHdmiphy1_MmcmReset(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, TRUE);
+	XHdmiphy1_MmcmReset(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, TRUE);
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+		XHdmiphy1_IBufDsEnable(InstancePtr, QuadId, XHDMIPHY1_DIR_TX, (FALSE));
+	}
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+		XHdmiphy1_IBufDsEnable(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, (FALSE));
+	}
+
+	/* DRU Settings. */
+	if (InstancePtr->Config.DruIsPresent) {
+		XHdmiphy1_IBufDsEnable(InstancePtr, QuadId, XHDMIPHY1_DIR_RX, TRUE);
+		XHdmiphy1_DruReset(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, TRUE);
+		XHdmiphy1_DruEnable(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, FALSE);
+	}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	/* Set to DFE */
+	XHdmiphy1_SetRxLpm(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_RX, 0);
+#endif
+
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		XHdmiphy1_SetTxVoltageSwing(InstancePtr, QuadId,
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+			(XHdmiphy1_ChannelId)Id, 0xB);
+#else
+			(XHdmiphy1_ChannelId)Id, 0x1F);
+#endif
+		XHdmiphy1_SetTxPreEmphasis(InstancePtr, QuadId,
+            (XHdmiphy1_ChannelId)Id, 0x4);
+		XHdmiphy1_SetTxPostCursor(InstancePtr, QuadId,
+            (XHdmiphy1_ChannelId)Id, 0x4);
+	}
+
+	/* Clear Interrupt Register */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_INTR_STS_REG,
+			0xFFFFFFFF);
+
+	/* Interrupt Enable. */
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_CPLL_LOCK);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_QPLL0_LOCK);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TXALIGN_DONE);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_QPLL1_LOCK);
+#else
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE);
+#endif
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+	XHdmiphy1_IntrEnable(InstancePtr,
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE);
+	XHdmiphy1_ClkDetEnable(InstancePtr, TRUE);
+
+	/* Set the flag to indicate the driver is. */
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+
+	/* Init done. */
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_INIT, 1);
+
+	return XST_SUCCESS;
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* This function Sets the System Clock Selection
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XHdmiphy1_HdmiSetSystemClockSelection(XHdmiphy1 *InstancePtr,
+                u8 QuadId)
+{
+	XHdmiphy1_PllType XHdmiphy1_QPllType;
+
+     XHdmiphy1_QPllType = XHDMIPHY1_PLL_TYPE_QPLL0;
+
+    /* Set system clock selections */
+    if (InstancePtr->Config.TxSysPllClkSel ==
+            InstancePtr->Config.RxSysPllClkSel) {
+        if (InstancePtr->Config.RxSysPllClkSel ==
+                XHDMIPHY1_SYSCLKSELDATA_TYPE_CPLL_OUTCLK) {
+            XHdmiphy1_PllInitialize(InstancePtr, QuadId,
+                    XHDMIPHY1_CHANNEL_ID_CHA,
+                    InstancePtr->Config.RxRefClkSel,
+                    InstancePtr->Config.RxRefClkSel,
+                    XHDMIPHY1_PLL_TYPE_CPLL,
+                    XHDMIPHY1_PLL_TYPE_CPLL);
+        }
+        else {
+            XHdmiphy1_PllInitialize(InstancePtr, QuadId,
+                    XHDMIPHY1_CHANNEL_ID_CMN0,
+                    InstancePtr->Config.RxRefClkSel,
+                    InstancePtr->Config.RxRefClkSel,
+                    XHdmiphy1_QPllType,
+                    XHdmiphy1_QPllType);
+        }
+    }
+    else if (InstancePtr->Config.TxSysPllClkSel ==
+            XHDMIPHY1_SYSCLKSELDATA_TYPE_CPLL_OUTCLK) {
+        XHdmiphy1_PllInitialize(InstancePtr, QuadId,
+                XHDMIPHY1_CHANNEL_ID_CHA,
+                InstancePtr->Config.RxRefClkSel,
+                InstancePtr->Config.TxRefClkSel,
+                XHDMIPHY1_PLL_TYPE_CPLL,
+                XHdmiphy1_QPllType);
+    }
+    else {
+        XHdmiphy1_PllInitialize(InstancePtr, QuadId,
+                XHDMIPHY1_CHANNEL_ID_CMN0,
+                InstancePtr->Config.TxRefClkSel,
+                InstancePtr->Config.RxRefClkSel,
+                XHdmiphy1_QPllType,
+                XHDMIPHY1_PLL_TYPE_CPLL);
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function Updates the HDMIPHY clocking.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	TxSysPllClkSel is the SYSCLKDATA selection for TX.
+* @param	RxSysPllClkSel is the SYSCLKDATA selection for RX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiUpdateClockSelection(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_SysClkDataSelType TxSysPllClkSel,
+		XHdmiphy1_SysClkDataSelType RxSysPllClkSel)
+{
+	u8 Id, Id0, Id1;
+
+	/* Reset PLL */
+	XHdmiphy1_ResetGtPll(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CHA,
+			XHDMIPHY1_DIR_RX, TRUE);
+	XHdmiphy1_ResetGtPll(InstancePtr, QuadId, XHDMIPHY1_CHANNEL_ID_CHA,
+			XHDMIPHY1_DIR_TX, TRUE);
+
+	/* Set default. */
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+			XHDMIPHY1_GT_STATE_IDLE;
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+			XHDMIPHY1_GT_STATE_IDLE;
+	}
+
+	/* Update Hdmiphy Clocking */
+	InstancePtr->Config.TxSysPllClkSel = TxSysPllClkSel;
+	InstancePtr->Config.RxSysPllClkSel = RxSysPllClkSel;
+	XHdmiphy1_HdmiSetSystemClockSelection(InstancePtr, QuadId);
+}
+
+/*****************************************************************************/
+/**
+* This function resets the GT TX alignment module.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Reset specifies TRUE/FALSE value to either assert or deassert
+*		reset on the TX alignment module, respectively.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_TxAlignReset(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Reset)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read TX align register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_TX_BUFFER_BYPASS_REG);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XHDMIPHY1_TX_BUFFER_BYPASS_TXPHDLYRESET_MASK(Id);
+	}
+
+	/* Write new value to BUFG_GT register. */
+	if (Reset) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+        XHDMIPHY1_TX_BUFFER_BYPASS_REG, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function resets the GT TX alignment module.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Start specifies TRUE/FALSE value to either start or ttop the TX
+*		alignment module, respectively.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_TxAlignStart(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Start)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read TX align register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_TX_BUFFER_BYPASS_REG);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XHDMIPHY1_TX_BUFFER_BYPASS_TXPHALIGN_MASK(Id);
+	}
+
+	/* Write new value to BUFG_GT register. */
+	if (Start) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+        XHDMIPHY1_TX_BUFFER_BYPASS_REG, RegVal);
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function enables the HDMIPHY's detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the clock detector respectively.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetEnable(XHdmiphy1 *InstancePtr, u8 Enable)
+{
+	u32 RegVal;
+
+	/* Read clkdet ctrl register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_CLKDET_CTRL_REG);
+
+	/* Write new value to clkdet ctrl register. */
+	if (Enable) {
+		RegVal |= XHDMIPHY1_CLKDET_CTRL_RUN_MASK;
+	}
+	else {
+		RegVal &= ~XHDMIPHY1_CLKDET_CTRL_RUN_MASK;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function clears the clock detector TX/RX timer.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetTimerClear(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	/* Read the clock detector control register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_CLKDET_CTRL_REG);
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegVal |= XHDMIPHY1_CLKDET_CTRL_TX_TMR_CLR_MASK;
+	}
+	else {
+		RegVal |= XHDMIPHY1_CLKDET_CTRL_RX_TMR_CLR_MASK;
+	}
+
+	/* Write new value to clkdet ctrl register. */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function resets clock detector TX/RX frequency.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetFreqReset(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	/* Read clkdet ctrl register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_CLKDET_CTRL_REG);
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegVal |= XHDMIPHY1_CLKDET_CTRL_TX_FREQ_RST_MASK;
+	}
+	else {
+		RegVal |= XHDMIPHY1_CLKDET_CTRL_RX_FREQ_RST_MASK;
+	}
+
+	/* Write new value to clkdet ctrl register. */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+void XHdmiphy1_TxPllreset(XHdmiphy1 *InstancePtr)
+{
+	u32 RegVal;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_PLL_RESET_REG);
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_PLL_RESET_REG, RegVal | 0x1);
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_PLL_RESET_REG, RegVal & ~0x1);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the clock detector frequency lock counter threshold value.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ThresholdVal is the threshold value to be set.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetSetFreqLockThreshold(XHdmiphy1 *InstancePtr,
+        u16 ThresholdVal)
+{
+	u32 RegVal;
+
+	/* Read clkdet ctrl register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_CLKDET_CTRL_REG);
+	RegVal &= ~XHDMIPHY1_CLKDET_CTRL_RX_FREQ_RST_MASK;
+
+	/* Update with new threshold. */
+	RegVal |= (ThresholdVal << XHDMIPHY1_CLKDET_CTRL_FREQ_LOCK_THRESH_SHIFT);
+
+	/* Write new value to clkdet ctrl register. */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function checks clock detector RX/TX frequency zero indicator bit.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	- TRUE if zero frequency.
+*		- FALSE otherwise, if non-zero frequency.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XHdmiphy1_ClkDetCheckFreqZero(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir)
+{
+	u32 MaskVal = 0;
+	u32 RegVal;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		MaskVal = XHDMIPHY1_CLKDET_STAT_TX_FREQ_ZERO_MASK;
+	}
+	else {
+		MaskVal = XHDMIPHY1_CLKDET_STAT_RX_FREQ_ZERO_MASK;
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_DRU_STAT_REG);
+	RegVal &= MaskVal;
+
+	if (RegVal) {
+		return (TRUE);
+	}
+
+	return (FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function sets clock detector frequency lock counter threshold value.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	TimeoutVal is the timeout value and is normally the system clock
+*		frequency.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetSetFreqTimeout(XHdmiphy1 *InstancePtr, u32 TimeoutVal)
+{
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_CLKDET_FREQ_TMR_TO_REG, TimeoutVal);
+}
+
+/*****************************************************************************/
+/**
+* This function loads the timer to TX/RX in the clock detector.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+* @param	TimeoutVal is the timeout value to store in the clock detector.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetTimerLoad(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, u32 TimeoutVal)
+{
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_CLKDET_TMR_TX_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_CLKDET_TMR_RX_REG;
+	}
+
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, TimeoutVal);
+}
+
+/*****************************************************************************/
+/**
+* This function returns the frequency of the RX/TX reference clock as
+* measured by the clock detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	The measured frequency of the RX/TX reference clock.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_ClkDetGetRefClkFreqHz(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir)
+{
+	u32 RegOffset;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_CLKDET_FREQ_TX_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_CLKDET_FREQ_RX_REG;
+	}
+
+	return XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+}
+
+/*****************************************************************************/
+/**
+* This function returns the frequency of the DRU reference clock as measured by
+* the clock detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	The measured frequency of the DRU reference clock.
+*
+* @note		The design must have a DRU for this function to return a valid
+*		value.
+*
+******************************************************************************/
+u32 XHdmiphy1_DruGetRefClkFreqHz(XHdmiphy1 *InstancePtr)
+{
+	u32 DruFreqHz = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_CLKDET_FREQ_DRU_REG);
+
+
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	if (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTHE4) {
+		if (DruFreqHz > XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK_MAX){
+			return XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK;
+		}
+		else if (DruFreqHz > XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK2_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK2_MAX){
+			return XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK2;
+		}
+	}
+	else if (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTYE4) {
+		if (DruFreqHz > XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK_MAX){
+			return XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK;
+		}
+		else if (DruFreqHz > XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK2_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK2_MAX){
+			return XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK2;
+		}
+	}
+	else {
+		if (DruFreqHz > XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK_MAX){
+			return XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK;
+		}
+		if (DruFreqHz > XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK1_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK1_MAX){
+			return XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK1;
+		}
+		if (DruFreqHz > XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK2_MIN &&
+				DruFreqHz < XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK2_MAX){
+			return XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK2;
+		}
+	}
+
+	/* Return Failure */
+	return XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+* This function resets the DRU in the HDMIPHY.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Reset specifies TRUE/FALSE value to either enable or disable
+*		the DRU respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_DruReset(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Reset)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read DRU ctrl register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_DRU_CTRL_REG);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XHDMIPHY1_DRU_CTRL_RST_MASK(Id);
+	}
+
+	/* Write DRU ctrl register. */
+	if (Reset) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_DRU_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function enabled/disables the DRU in the HDMIPHY.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the DRU, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_DruEnable(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Enable)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read DRU ctrl register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_DRU_CTRL_REG);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XHDMIPHY1_DRU_CTRL_EN_MASK(Id);
+	}
+
+	/* Write DRU ctrl register. */
+	if (Enable) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_DRU_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function gets the DRU version
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	None.
+*
+******************************************************************************/
+u16 XHdmiphy1_DruGetVersion(XHdmiphy1 *InstancePtr)
+{
+	u32 RegVal;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_DRU_STAT_REG);
+	RegVal &= XHDMIPHY1_DRU_STAT_VERSION_MASK;
+	RegVal >>= XHDMIPHY1_DRU_STAT_VERSION_SHIFT;
+
+	return ((u16)RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the DRU center frequency.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ChId specifies the channel ID.
+* @param	CenterFreqHz is the frequency value to set.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_DruSetCenterFreqHz(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_ChannelId ChId, u64 CenterFreqHz)
+{
+	u32 CenterFreqL;
+	u32 CenterFreqH;
+	u32 RegOffset;
+	u8 Id, Id0, Id1;
+
+	/* Split the 64-bit input into 2 32-bit values. */
+	CenterFreqL = (u32)CenterFreqHz;
+	CenterFreqHz >>= 32;
+	CenterFreqHz &= XHDMIPHY1_DRU_CFREQ_H_MASK;;
+	CenterFreqH = (u32)CenterFreqHz;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		RegOffset = XHDMIPHY1_DRU_CFREQ_L_REG(Id);
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset,
+				CenterFreqL);
+
+		RegOffset = XHDMIPHY1_DRU_CFREQ_H_REG(Id);
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset,
+				CenterFreqH);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the center frequency value for the DRU.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return	The calculated DRU Center frequency value.
+*
+* @note		According to XAPP1240:
+*			Center_f = fDIN * (2^32)/fdruclk
+*		The DRU clock is derived from the measured reference clock and
+*		the current QPLL settings.
+*
+******************************************************************************/
+u64 XHdmiphy1_DruCalcCenterFreqHz(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId)
+{
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_Channel *ChPtr;
+	u64 DruRefClk;
+#endif
+	u64 ClkDetRefClk;
+	u64 DataRate;
+	u64 FDin;
+	u64 FDruClk;
+
+	ClkDetRefClk = XHdmiphy1_ClkDetGetRefClkFreqHz(InstancePtr,
+                        XHDMIPHY1_DIR_RX);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	DruRefClk = XHdmiphy1_DruGetRefClkFreqHz(InstancePtr);
+
+	/* Take the master channel (channel 1). */
+	ChPtr = &InstancePtr->Quads[QuadId].Ch1;
+
+	if ((ChId == XHDMIPHY1_CHANNEL_ID_CMN0) ||
+			(ChId == XHDMIPHY1_CHANNEL_ID_CMN1)) {
+		FDruClk = (DruRefClk * InstancePtr->Quads[QuadId].Plls[
+			          XHDMIPHY1_CH2IDX(ChId)].PllParams.NFbDiv) /
+			      (InstancePtr->Quads[QuadId].Plls[
+			          XHDMIPHY1_CH2IDX(ChId)].PllParams.MRefClkDiv *
+			          (ChPtr->RxOutDiv * 20));
+	}
+	else {
+		FDruClk = (DruRefClk * ChPtr->PllParams.N1FbDiv *
+			ChPtr->PllParams.N2FbDiv * 2) /
+			(ChPtr->PllParams.MRefClkDiv * ChPtr->RxOutDiv * 20);
+	}
+#else
+	/* Supress Warning */
+	QuadId = QuadId;
+	ChId = ChId;
+
+	FDruClk = (u64) (XHDMIPHY1_HDMI_GTYE5_DRU_LRATE / 20);
+#endif
+	DataRate = 10 * ClkDetRefClk;
+	FDin = DataRate * ((u64)1 << 32);
+
+	/* Check for divide by zero. */
+	if (FDin && FDruClk) {
+		return (FDin / FDruClk);
+	}
+	return 0;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the GT RX CDR and Equalization for DRU mode.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Enable enables the DRU logic (when 1), or disables (when 0).
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiGtDruModeEnable(XHdmiphy1 *InstancePtr, u8 Enable)
+{
+	u32 RegVal;
+	u32 RegMask = 0;
+	u8 Id, Id0, Id1;
+
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_DRU_EN, Enable);
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_RX_EQ_CDR_REG);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		RegMask |= XHDMIPHY1_RX_STATUS_RXCDRHOLD_MASK(Id) |
+			XHDMIPHY1_RX_STATUS_RXOSOVRDEN_MASK(Id) |
+			XHDMIPHY1_RX_STATUS_RXLPMLFKLOVRDEN_MASK(Id) |
+			XHDMIPHY1_RX_STATUS_RXLPMHFOVRDEN_MASK(Id);
+	}
+
+	if (Enable) {
+		RegVal |= RegMask;
+	}
+	else {
+		RegVal &= ~RegMask;
+	}
+
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_RX_EQ_CDR_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the HDMI MMCM parameters.
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+* @param	Ppc specifies the total number of pixels per clock.
+*		- 1 = XVIDC_PPC_1
+*		- 2 = XVIDC_PPC_2
+*		- 4 = XVIDC_PPC_4
+* @param	Bpc specifies the color depth/bits per color component.
+*		- 6 = XVIDC_BPC_6
+*		- 8 = XVIDC_BPC_8
+*		- 10 = XVIDC_BPC_10
+*		- 12 = XVIDC_BPC_12
+*		- 16 = XVIDC_BPC_16
+*
+* @return
+*		- XST_SUCCESS if calculated PLL parameters updated successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiCfgCalcMmcmParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+		XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc)
+{
+	u32 RefClk;
+	u16 Div;
+	u16 Mult;
+	u16 MultDiv;
+	u8 Valid;
+	u64 LineRate = 0;
+	XHdmiphy1_Mmcm *MmcmPtr;
+	XHdmiphy1_PllType PllType;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	/* Get line rate. */
+	PllType = XHdmiphy1_GetPllType(InstancePtr, 0, Dir,
+			XHDMIPHY1_CHANNEL_ID_CH1);
+
+	switch (PllType) {
+		case XHDMIPHY1_PLL_TYPE_QPLL:
+		case XHDMIPHY1_PLL_TYPE_QPLL0:
+		case XHDMIPHY1_PLL_TYPE_LCPLL:
+			LineRate = InstancePtr->Quads[QuadId].Cmn0.LineRateHz;
+			break;
+		case XHDMIPHY1_PLL_TYPE_QPLL1:
+		case XHDMIPHY1_PLL_TYPE_RPLL:
+			LineRate = InstancePtr->Quads[QuadId].Cmn1.LineRateHz;
+			break;
+		default:
+			LineRate = InstancePtr->Quads[QuadId].Ch1.LineRateHz;
+			break;
+	}
+
+	if (((LineRate / 1000000) > 2970) && (Ppc == XVIDC_PPC_1)) {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_1PPC_ERR, 1);
+		XHdmiphy1_ErrorHandler(InstancePtr);
+		return (XST_FAILURE);
+	}
+
+	Div = 1;
+
+	do {
+		if (Dir == XHDMIPHY1_DIR_RX) {
+			RefClk = InstancePtr->HdmiRxRefClkHz;
+			MmcmPtr= &InstancePtr->Quads[QuadId].RxMmcm;
+
+			RefClk = RefClk / (GetGtHdmiPtr(InstancePtr))->RxMmcmScale;
+			Mult = (GetGtHdmiPtr(InstancePtr))->RxMmcmFvcoMax * Div / RefClk;
+		}
+		else {
+			RefClk = InstancePtr->HdmiTxRefClkHz;
+			MmcmPtr= &InstancePtr->Quads[QuadId].TxMmcm;
+
+			RefClk = RefClk / (GetGtHdmiPtr(InstancePtr))->TxMmcmScale;
+			Mult = (GetGtHdmiPtr(InstancePtr))->TxMmcmFvcoMax * Div / RefClk;
+		}
+
+		/* Return if RefClk is below valid range */
+		if (RefClk < 20000000) {
+			return (XST_FAILURE);
+		}
+
+		/* In case of 4 pixels per clock, the M must be a multiple of four. */
+		if (Ppc == XVIDC_PPC_4) {
+			Mult = Mult / 4;
+			Mult = Mult * 4;
+		}
+		/* Else the M must be a multiple of two. */
+		else if (Ppc == XVIDC_PPC_2) {
+			Mult = Mult / 2;
+			Mult = Mult * 2;
+		}
+
+
+		Valid = (FALSE);
+		do {
+            MultDiv = Mult / Div;
+			MmcmPtr->ClkFbOutMult = Mult;
+			MmcmPtr->DivClkDivide = Div;
+
+			if (InstancePtr->Config.TransceiverWidth == 4) {
+				/* Link clock: TMDS clock ratio 1/40. */
+				if ((LineRate / 1000000) >= 3400) {
+					if ((Dir == XHDMIPHY1_DIR_TX) &&
+							(((LineRate / 1000000) / InstancePtr->
+									HdmiTxSampleRate) < 3400)) {
+						MmcmPtr->ClkOut0Div = MultDiv * 4;
+					}
+					else {
+						MmcmPtr->ClkOut0Div = MultDiv;
+					}
+				}
+				/* Link clock: TMDS clock ratio 1/10. */
+				else {
+					MmcmPtr->ClkOut0Div = MultDiv * 4;
+				}
+			}
+			else { /* 2 Byte Mode */
+				/* Link clock: TMDS clock ratio 1/40. */
+				if ((LineRate / 1000000) >= 3400) {
+					if ((Dir == XHDMIPHY1_DIR_TX) &&
+							(((LineRate / 1000000) / InstancePtr->
+									HdmiTxSampleRate) < 3400)) {
+						MmcmPtr->ClkOut0Div = MultDiv * 2;
+					}
+					else {
+						MmcmPtr->ClkOut0Div = MultDiv / 2;
+					}
+				}
+				/* Link clock: TMDS clock ratio 1/10. */
+				else {
+					MmcmPtr->ClkOut0Div = MultDiv * 2;
+				}
+			}
+
+			/* TMDS Clock */
+			MmcmPtr->ClkOut1Div = MultDiv * ((Dir == XHDMIPHY1_DIR_TX) ?
+					(InstancePtr->HdmiTxSampleRate) : 1);
+
+			/* Video clock. */
+			MmcmPtr->ClkOut2Div = 0;
+
+			switch (Bpc) {
+			case XVIDC_BPC_10:
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 5 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					/* The clock ratio is 2.5 */
+					/* The PLL only supports integer values */
+					/* The MultDiv must be dividable by two (2 * 2.5 = 5)
+						to get an integer number */
+					if ((MultDiv % 2) == 0) {
+						MmcmPtr->ClkOut2Div = (MultDiv * 5 / 2 *
+							((Dir == XHDMIPHY1_DIR_TX)?
+							(InstancePtr->HdmiTxSampleRate) : 1));
+					}
+				}
+				/* Single pixel. */
+				else {
+					/* The clock ratio is 1.25 */
+					/* The PLL only supports integer values */
+					/* The MultDiv must be dividable by four (4 * 1.25 = 5)
+						to get an integer number */
+					if ((MultDiv % 4) == 0) {
+						MmcmPtr->ClkOut2Div = (MultDiv * 5 / 4 *
+							((Dir == XHDMIPHY1_DIR_TX) ?
+							(InstancePtr->HdmiTxSampleRate) : 1));
+					}
+				}
+				break;
+			case XVIDC_BPC_12:
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 6 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 3 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Single pixel. */
+				else {
+					/* The clock ratio is 1.5 */
+					/* The PLL only supports integer values */
+					/* The MultDiv must be dividable by two (2 * 1.5 = 3)
+						to get an integer number */
+					if ((MultDiv % 2) == 0) {
+						MmcmPtr->ClkOut2Div = (MultDiv * 3 / 2 *
+							((Dir == XHDMIPHY1_DIR_TX) ?
+							(InstancePtr->HdmiTxSampleRate) : 1));
+					}
+				}
+				break;
+			case XVIDC_BPC_16 :
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 8 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 4 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Single pixel. */
+				else {
+					MmcmPtr->ClkOut2Div = (MultDiv * 2 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				break;
+			case XVIDC_BPC_8:
+			default:
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 4 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 2 *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Single pixel. */
+				else {
+					MmcmPtr->ClkOut2Div = (MultDiv *
+						((Dir == XHDMIPHY1_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				break;
+			}
+
+			/* Only do this when the ClkOut2Div has been set */
+			if (MmcmPtr->ClkOut2Div) {
+				if (Dir == XHDMIPHY1_DIR_RX) {
+					/* Correct divider value if TMDS clock ratio is 1/40. */
+					if (InstancePtr->HdmiRxTmdsClockRatio) {
+						if ((MmcmPtr->ClkOut2Div % 4) == 0) {
+							MmcmPtr->ClkOut2Div = MmcmPtr->ClkOut2Div / 4;
+						}
+						/* Not divisible by 4: repeat loop with a lower
+						 * multiply value. */
+						else {
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+							MmcmPtr->ClkOut2Div = 255;
+#else
+							MmcmPtr->ClkOut2Div = 65535;
+#endif
+						}
+					}
+				}
+				/* TX. */
+				else if ((((LineRate / 1000000) >= 3400) &&
+							(InstancePtr->HdmiTxSampleRate == 1)) ||
+						 (((LineRate / 1000000) / InstancePtr->
+								HdmiTxSampleRate) >= 3400)) {
+					if ((MmcmPtr->ClkOut2Div % 4) == 0) {
+						MmcmPtr->ClkOut2Div = MmcmPtr->ClkOut2Div / 4;
+					}
+					/* Not divisible by 4: repeat loop with a lower
+					 * multiply value. */
+					else {
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+						MmcmPtr->ClkOut2Div = 255;
+#else
+						MmcmPtr->ClkOut2Div = 65535;
+#endif
+					}
+				}
+			}
+
+			/* Check values. */
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+			if ((MmcmPtr->ClkOut0Div > 0) && (MmcmPtr->ClkOut0Div <= 128) &&
+				(MmcmPtr->ClkOut1Div > 0) && (MmcmPtr->ClkOut1Div <= 128) &&
+				(MmcmPtr->ClkOut2Div > 0) && (MmcmPtr->ClkOut2Div <= 128)) {
+#else
+			if ((MmcmPtr->ClkOut0Div > 0) && (MmcmPtr->ClkOut0Div <= 511) &&
+				(MmcmPtr->ClkOut1Div > 0) && (MmcmPtr->ClkOut1Div <= 511) &&
+				(MmcmPtr->ClkOut2Div > 0) && (MmcmPtr->ClkOut2Div <= 511)) {
+#endif
+				Valid = (TRUE);
+			}
+			else {
+				/* 4 pixels per clock. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					/* Decrease Mult value. */
+					Mult -= 4;
+				}
+				/* 2 pixels per clock. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					/* Decrease M value. */
+					Mult -= 2;
+				}
+				/* 1 pixel per clock */
+				else {
+					/* Decrease M value */
+					Mult -= 1;
+				}
+			}
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+		} while (!Valid && (Mult > 3) && (Mult < 432));
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4 || \
+     XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+		} while (!Valid && (Mult > 0) && (Mult < 129));
+#else
+		} while (!Valid && (Mult > 0) && (Mult < 65));
+#endif
+
+		/* Increment divider */
+		Div++;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+	} while (!Valid && (Div > 0) && (Div < 124));
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4 || \
+     XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	} while (!Valid && (Div > 0) && (Div < 107));
+#else
+	} while (!Valid && (Div > 0) && (Div < 20));
+#endif
+
+	if (Valid) {
+		return (XST_SUCCESS);
+	}
+	else {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_MMCM_ERR, 1);
+		XHdmiphy1_ErrorHandler(InstancePtr);
+		return (XST_FAILURE);
+	}
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* This function calculates the QPLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if calculated QPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiQpllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 Status;
+	u64 RefClk = 0;
+	u32 *RefClkPtr;
+	u64 TxLineRate = 0;
+	u8 Id, Id0, Id1;
+
+	u8 SRArray[] = {1, 3, 5};
+	u8 SRIndex;
+	u8 SRValue;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	XHdmiphy1_SysClkDataSelType SysClkDataSel =
+        (XHdmiphy1_SysClkDataSelType) 0;
+	XHdmiphy1_SysClkOutSelType SysClkOutSel =
+        (XHdmiphy1_SysClkOutSelType) 0;
+	XHdmiphy1_ChannelId ActiveCmnId =
+        XHDMIPHY1_CHANNEL_ID_CMN0;
+
+	u32 QpllRefClk;
+	u32 QpllClkMin = 0;
+
+	/* Determine QPLL reference clock from the first (master) channel. */
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		QpllRefClk = InstancePtr->HdmiRxRefClkHz;
+		RefClkPtr = &InstancePtr->HdmiRxRefClkHz;
+	}
+	else {
+		QpllRefClk = InstancePtr->HdmiTxRefClkHz;
+		RefClkPtr = &InstancePtr->HdmiTxRefClkHz;
+	}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+	/* Determine which QPLL to use. */
+	if (((102343750 <= QpllRefClk) && (QpllRefClk <= 122500000)) ||
+		((204687500 <= QpllRefClk) && (QpllRefClk <= 245000000)) ||
+		((409375000 <= QpllRefClk) && (QpllRefClk <= 490000000))) {
+		SysClkDataSel = XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK;
+		SysClkOutSel = XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL1_REFCLK;
+		ActiveCmnId = XHDMIPHY1_CHANNEL_ID_CMN1;
+		QpllClkMin = (u32) XHDMIPHY1_HDMI_GTHE4_QPLL1_REFCLK_MIN;
+	}
+	else {
+		SysClkDataSel = XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK;
+		SysClkOutSel = XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL0_REFCLK;
+		ActiveCmnId = XHDMIPHY1_CHANNEL_ID_CMN0;
+		QpllClkMin = (u32) XHDMIPHY1_HDMI_GTHE4_QPLL0_REFCLK_MIN;
+	}
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	/* Determine which QPLL to use. */
+	if (((102343750 <= QpllRefClk) && (QpllRefClk <= 122500000)) ||
+		((204687500 <= QpllRefClk) && (QpllRefClk <= 245000000)) ||
+		((409375000 <= QpllRefClk) && (QpllRefClk <= 490000000))) {
+		SysClkDataSel = XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK;
+		SysClkOutSel = XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL1_REFCLK;
+		ActiveCmnId = XHDMIPHY1_CHANNEL_ID_CMN1;
+		QpllClkMin = (u32) XHDMIPHY1_HDMI_GTYE4_QPLL1_REFCLK_MIN;
+	}
+	else {
+		SysClkDataSel = XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK;
+		SysClkOutSel = XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL0_REFCLK;
+		ActiveCmnId = XHDMIPHY1_CHANNEL_ID_CMN0;
+		QpllClkMin = (u32) XHDMIPHY1_HDMI_GTYE4_QPLL0_REFCLK_MIN;
+	}
+#endif
+
+	/* Update QPLL clock selections. */
+	XHdmiphy1_CfgSysClkDataSel(InstancePtr, QuadId, Dir, SysClkDataSel);
+	XHdmiphy1_CfgSysClkOutSel(InstancePtr, QuadId, Dir, SysClkOutSel);
+
+	/* RX is using QPLL. */
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		/* Check if the reference clock is not below the minimum QPLL
+		 * input frequency. */
+		if (QpllRefClk >= QpllClkMin) {
+			RefClk = QpllRefClk;
+
+			/* Scaled line rate. */
+			if (InstancePtr->RxHdmi21Cfg.IsEnabled == 0) {
+				if (InstancePtr->HdmiRxTmdsClockRatio) {
+					XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						XHDMIPHY1_CHANNEL_ID_CMNA, (RefClk * 40));
+				}
+				else {
+					XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						XHDMIPHY1_CHANNEL_ID_CMNA, (RefClk * 10));
+				}
+			} else { /* InstancePtr->RxHdmi21Cfg.IsEnabled == 1 */
+				XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						XHDMIPHY1_CHANNEL_ID_CMNA,
+						InstancePtr->RxHdmi21Cfg.LineRate);
+			}
+
+			/* Clear DRU is enabled flag. */
+			InstancePtr->HdmiRxDruIsEnabled = 0;
+
+			/* Set RX data width. */
+			XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA,
+					&Id0, &Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				if (InstancePtr->Config.TransceiverWidth == 2) {
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxDataWidth = 20;
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxIntDataWidth = 2;
+				}
+				else {
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxDataWidth = 40;
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxIntDataWidth = 4;
+				}
+			}
+
+		}
+		/* The reference clock is below the minimum frequency thus
+		 * select the DRU. */
+		else if (InstancePtr->Config.DruIsPresent) {
+			RefClk = XHdmiphy1_DruGetRefClkFreqHz(InstancePtr);
+            /* Check DRU frequency */
+			if (RefClk == XST_FAILURE) {
+				XHdmiphy1_LogWrite(InstancePtr,
+						XHDMIPHY1_LOG_EVT_DRU_CLK_ERR, 1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+
+			/* Round input frequency to 10 kHz. */
+			RefClk = (RefClk+5000) / 10000;
+			RefClk = RefClk * 10000;
+
+			/* Set the DRU to operate at a linerate of 2.5 Gbps. */
+			XHdmiphy1_CfgLineRate(InstancePtr,
+				QuadId, XHDMIPHY1_CHANNEL_ID_CMNA,
+				(GetGtHdmiPtr(InstancePtr))->DruLineRate);
+
+			/* Set DRU is enabled flag. */
+			InstancePtr->HdmiRxDruIsEnabled = 1;
+
+			/* Set RX data width to 40 and 4 bytes. */
+			XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA,
+					&Id0, &Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[QuadId].Plls[
+					XHDMIPHY1_CH2IDX(Id)].RxDataWidth = 20;
+				InstancePtr->Quads[QuadId].Plls[
+					XHDMIPHY1_CH2IDX(Id)].RxIntDataWidth = 2;
+			}
+		}
+		else {
+			XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_NO_DRU, 1);
+			XHdmiphy1_ErrorHandler(InstancePtr);
+			return (XST_FAILURE);
+		}
+	}
+
+	/* TX is using QPLL. */
+	else {
+		/* Set default TX sample rate. */
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		if (InstancePtr->TxHdmi21Cfg.IsEnabled == 0) {
+			/* Update TX line rates. */
+			XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+                XHDMIPHY1_CHANNEL_ID_CMNA, (u64)((*RefClkPtr) * 10));
+			TxLineRate = (*RefClkPtr) / 100000;;
+
+			/* Check if the linerate is above the 340 Mcsc. */
+			if ((TxLineRate) >= 3400) {
+				(*RefClkPtr) = (*RefClkPtr) / 4;
+			}
+		} else { /* InstancePtr->TxHdmi21Cfg.IsEnabled == 1 */
+			XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+					XHDMIPHY1_CHANNEL_ID_CMNA,
+					InstancePtr->TxHdmi21Cfg.LineRate);
+		}
+	}
+
+	/* Calculate QPLL values. */
+	for (SRIndex = 0; SRIndex < sizeof(SRArray); SRIndex++) {
+		/* Only use oversampling when then TX is using the QPLL. */
+		if (Dir == XHDMIPHY1_DIR_TX) {
+			SRValue = SRArray[SRIndex];
+
+			if (InstancePtr->TxHdmi21Cfg.IsEnabled == 0) {
+				/* TX reference clock is below the minimum QPLL clock
+				 * input frequency. */
+				if ((*RefClkPtr) < QpllClkMin) {
+					RefClk = ((*RefClkPtr) * SRValue);
+
+					/* Calculate scaled line rate. */
+					if (TxLineRate >= 3400) {
+						XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+							XHDMIPHY1_CHANNEL_ID_CMNA,
+							(u64)(RefClk * 40));
+					}
+					else {
+						XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+							XHDMIPHY1_CHANNEL_ID_CMNA,
+							(u64)(RefClk * 10));
+					}
+				}
+				/* TX reference clock is in QPLL clock input range.
+				 * In this case don't increase the reference clock, but
+				 * increase the line rate. */
+				else {
+					RefClk = (*RefClkPtr);
+
+					/* Calculate scaled line rate. */
+					if (TxLineRate >= 3400) {
+						XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+							XHDMIPHY1_CHANNEL_ID_CMNA,
+							(u64)(RefClk * 40 *SRValue));
+					}
+
+					else {
+						XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+							XHDMIPHY1_CHANNEL_ID_CMNA,
+							(u64)(RefClk * 10 *SRValue));
+					}
+				}
+			}
+			else { /* InstancePtr->TxHdmi21Cfg.IsEnabled == 1 */
+				RefClk = (*RefClkPtr);
+			}
+		}
+		/* For all other reference clocks force sample rate to one. */
+		else {
+			SRValue = 1;
+		}
+
+		Status = XHdmiphy1_ClkCalcParams(InstancePtr, QuadId, ActiveCmnId,
+						Dir, RefClk);
+		if (Status == (XST_SUCCESS)) {
+			/* Only execute when the TX is using the QPLL. */
+			if (Dir == XHDMIPHY1_DIR_TX) {
+				/* Set TX sample rate. */
+				InstancePtr->HdmiTxSampleRate = SRValue;
+
+				/* Update reference clock only when the
+				 * reference clock is below the minimum QPLL
+				 * input frequency. */
+				if ((*RefClkPtr) < QpllClkMin) {
+					(*RefClkPtr) = (*RefClkPtr) * SRValue;
+				}
+				else if (SRValue > 1) {
+					XHdmiphy1_LogWrite(InstancePtr,
+							XHDMIPHY1_LOG_EVT_GT_QPLL_CFG_ERR, 1);
+					XHdmiphy1_ErrorHandler(InstancePtr);
+					return (XST_FAILURE);
+				}
+			}
+
+			/* Check Userclock Frequency */
+            /* (300 MHz + 0.5%) + 10 KHz (Clkdet accuracy) */
+			if (301500000 <
+					(XHdmiphy1_GetLineRateHz(InstancePtr, QuadId,
+							ActiveCmnId) /
+					(InstancePtr->Config.TransceiverWidth * 10))) {
+				XHdmiphy1_LogWrite(InstancePtr,
+						XHDMIPHY1_LOG_EVT_USRCLK_ERR, 1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+			return (XST_SUCCESS);
+		}
+	}
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_GT_QPLL_CFG_ERR, 1);
+	XHdmiphy1_ErrorHandler(InstancePtr);
+	return (XST_FAILURE);
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the CPLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if calculated CPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_HdmiCpllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 Status;
+	u64 RefClk = 0;
+	u32 *RefClkPtr;
+	u32 TxLineRate = 0;
+	XHdmiphy1_ChannelId ChannelId = XHDMIPHY1_CHANNEL_ID_CHA;
+	u8 Id, Id0, Id1;
+
+	u8 SRArray[] = {1, 3, 5};
+	u8 SRIndex;
+	u8 SRValue;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	/* TX is using CPLL. */
+	if (Dir == XHDMIPHY1_DIR_TX) {
+
+		/* Set default TX sample rate. */
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		/* Set line rate.  */
+		RefClkPtr = &InstancePtr->HdmiTxRefClkHz;
+		if (InstancePtr->TxHdmi21Cfg.IsEnabled == 0) {
+			XHdmiphy1_CfgLineRate(InstancePtr, QuadId, ChannelId,
+					(u64)((*RefClkPtr) * 10));
+			TxLineRate = (*RefClkPtr)  / 100000;
+
+			/* Check if the line rate is above the 340 Mcsc. */
+			if (TxLineRate >= 3400) {
+				(*RefClkPtr) = (*RefClkPtr) / 4;
+			}
+		} else { /* InstancePtr->TxHdmi21Cfg.IsEnabled == 1 */
+			XHdmiphy1_CfgLineRate(InstancePtr, QuadId, ChannelId,
+					(u64)(InstancePtr->TxHdmi21Cfg.LineRate));
+			TxLineRate = InstancePtr->TxHdmi21Cfg.LineRate / 100000;
+		}
+	}
+	/* RX is using CPLL. */
+	else {
+		RefClkPtr = &InstancePtr->HdmiRxRefClkHz;
+
+		/* Check if the reference clock is not below the minimum CPLL
+		 * input frequency. */
+		if ((*RefClkPtr) >=
+				(GetGtHdmiPtr(InstancePtr))->CpllRefClkMin) {
+			RefClk = (*RefClkPtr);
+
+			/* Scaled linerate */
+			if (InstancePtr->RxHdmi21Cfg.IsEnabled == 0) {
+				if (InstancePtr->HdmiRxTmdsClockRatio) {
+					XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						ChannelId, (RefClk * 40));
+				}
+				else {
+					XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						ChannelId, (RefClk * 10));
+				}
+			} else { /* InstancePtr->RxHdmi21Cfg.IsEnabled == 1 */
+				XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+					ChannelId, InstancePtr->RxHdmi21Cfg.LineRate);
+			}
+
+			/* Clear DRU is enabled flag. */
+			InstancePtr->HdmiRxDruIsEnabled = 0;
+
+			/* Set RX data width. */
+			XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA,
+					&Id0, &Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				if (InstancePtr->Config.TransceiverWidth == 2) {
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxDataWidth = 20;
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxIntDataWidth = 2;
+				}
+				else {
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxDataWidth = 40;
+					InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].
+						RxIntDataWidth = 4;
+				}
+			}
+
+		}
+		/* The reference clock is below the minimum frequency thus
+		 * select the DRU. */
+		else {
+			if (InstancePtr->Config.DruIsPresent) {
+				/* Return config not found error when TMDS ratio is 1/40 */
+                if (InstancePtr->HdmiRxTmdsClockRatio) {
+                    XHdmiphy1_LogWrite(InstancePtr,
+                        XHDMIPHY1_LOG_EVT_GT_CPLL_CFG_ERR, 1);
+                    XHdmiphy1_ErrorHandler(InstancePtr);
+                    return (XST_FAILURE);
+                }
+
+                RefClk = XHdmiphy1_DruGetRefClkFreqHz(InstancePtr);
+                /* Check DRU frequency */
+			if (RefClk == XST_FAILURE) {
+				XHdmiphy1_LogWrite(InstancePtr,
+						XHDMIPHY1_LOG_EVT_DRU_CLK_ERR, 1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+				/* Round input frequency to 10 kHz. */
+				RefClk = (RefClk+5000) / 10000;
+				RefClk = RefClk * 10000;
+
+				/* Set the DRU to operate at a linerate of
+				 * 2.5 Gbps. */
+				XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						ChannelId,
+						(GetGtHdmiPtr(InstancePtr))->
+						DruLineRate);
+
+				/* Set DRU is enabled flag. */
+				InstancePtr->HdmiRxDruIsEnabled = 1;
+
+				/* Set RX data width. */
+				XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA,
+						&Id0, &Id1);
+				for (Id = Id0; Id <= Id1; Id++) {
+					InstancePtr->Quads[QuadId].Plls[
+						XHDMIPHY1_CH2IDX(Id)].
+						RxDataWidth = 20;
+					InstancePtr->Quads[QuadId].Plls[
+						XHDMIPHY1_CH2IDX(Id)].
+						RxIntDataWidth = 2;
+				}
+
+				if (TxLineRate > (((GetGtHdmiPtr(InstancePtr))
+						->DruLineRate) / 1000000)) {
+					XHdmiphy1_LogWrite(InstancePtr,
+							XHDMIPHY1_LOG_EVT_VD_NOT_SPRTD_ERR, 1);
+                    XHdmiphy1_ErrorHandler(InstancePtr);
+                    return (XST_FAILURE);
+				}
+			}
+			else {
+				/* Return config not found error when TMDS ratio is 1/40 */
+                if (InstancePtr->HdmiRxTmdsClockRatio) {
+                    XHdmiphy1_LogWrite(InstancePtr,
+                        XHDMIPHY1_LOG_EVT_GT_CPLL_CFG_ERR, 1);
+                    XHdmiphy1_ErrorHandler(InstancePtr);
+                }
+                else {
+					XHdmiphy1_LogWrite(InstancePtr,
+							XHDMIPHY1_LOG_EVT_NO_DRU, 1);
+					XHdmiphy1_ErrorHandler(InstancePtr);
+                }
+                return (XST_FAILURE);
+			}
+		}
+	}
+
+	/* Try different sample rates. */
+	for (SRIndex = 0; SRIndex < sizeof(SRArray); SRIndex++) {
+		/* Only use oversampling when then TX is using the CPLL. */
+		if (Dir == XHDMIPHY1_DIR_TX) {
+			SRValue = SRArray[SRIndex];
+
+			if (InstancePtr->TxHdmi21Cfg.IsEnabled == 0) {
+				/* Multiply the reference clock with the sample rate
+				 * value. */
+				RefClk = ((*RefClkPtr) * SRValue);
+
+				/* Calculate scaled line rate. */
+				if (TxLineRate >= 3400) {
+					XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						ChannelId, (RefClk * 40));
+				}
+				else {
+					XHdmiphy1_CfgLineRate(InstancePtr, QuadId,
+						ChannelId, (RefClk * 10));
+				}
+			}
+			else { /* InstancePtr->TxHdmi21Cfg.IsEnabled == 1 */
+				RefClk = (*RefClkPtr);
+			}
+		}
+		/* For all other reference clocks force sample rate to one. */
+		else {
+			SRValue = 1;
+		}
+
+		Status = XHdmiphy1_ClkCalcParams(InstancePtr, QuadId,
+					ChannelId, Dir, RefClk);
+		if (Status == (XST_SUCCESS)) {
+			/* Only execute when the TX is using the QPLL. */
+			if (Dir == XHDMIPHY1_DIR_TX) {
+				InstancePtr->HdmiTxSampleRate = SRValue;
+				(*RefClkPtr) = (*RefClkPtr) * SRValue;
+			}
+
+			/* Check Userclock Frequency */
+            /* (300 MHz + 0.5%) + 10 KHz (Clkdet accuracy) */
+			if (301500000 <	(XHdmiphy1_GetLineRateHz(InstancePtr, QuadId,
+							XHDMIPHY1_CHANNEL_ID_CH1) /
+					(InstancePtr->Config.TransceiverWidth * 10))) {
+				XHdmiphy1_LogWrite(InstancePtr,
+						XHDMIPHY1_LOG_EVT_USRCLK_ERR, 1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+			return (XST_SUCCESS);
+		}
+	}
+
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_GT_CPLL_CFG_ERR, 1);
+	XHdmiphy1_ErrorHandler(InstancePtr);
+	return (XST_FAILURE);
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function sets the MMCM programming values based on Max Rate
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return       None
+*
+* @note         Based on the MAX Rate set in the GUI, the MMCM values are
+*               selected.
+*               3  -> Max Rate selected in GUI is 3G
+*               6  -> Max Rate selected in GUI is 6G
+*               8  -> Max Rate selected in GUI is 8G
+*               10 -> Max Rate selected in GUI is 10G
+*               12 -> Max Rate selected in GUI in 12G
+*
+******************************************************************************/
+static void XHdmiphy1_MmcmParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir)
+{
+	u8 MaxRate;
+	u8 NumChannels;
+	XHdmiphy1_Mmcm *MmcmPtr;
+
+	if (Dir == XHDMIPHY1_DIR_RX) {
+		MmcmPtr = &InstancePtr->Quads[QuadId].RxMmcm;
+		MaxRate = InstancePtr->Config.RxMaxRate;
+		NumChannels = InstancePtr->Config.RxChannels;
+	}
+	else {
+		MmcmPtr = &InstancePtr->Quads[QuadId].TxMmcm;
+		MaxRate = InstancePtr->Config.TxMaxRate;
+		NumChannels = InstancePtr->Config.TxChannels;
+	}
+
+	switch (MaxRate) {
+	case 3:
+		MmcmPtr->ClkFbOutMult =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT3x3;
+		MmcmPtr->DivClkDivide =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK3x3;
+		MmcmPtr->ClkOut0Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV3x3;
+		MmcmPtr->ClkOut1Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV3x3;
+		MmcmPtr->ClkOut2Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV3x3;
+		break;
+	case 6:
+		if (NumChannels == 3) {
+			MmcmPtr->ClkFbOutMult =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT6x3;
+			MmcmPtr->DivClkDivide =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK6x3;
+			MmcmPtr->ClkOut0Div =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV6x3;
+			MmcmPtr->ClkOut1Div =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV6x3;
+			MmcmPtr->ClkOut2Div =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV6x3;
+		} else {
+			MmcmPtr->ClkFbOutMult =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT6;
+			MmcmPtr->DivClkDivide =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK6;
+			MmcmPtr->ClkOut0Div =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV6;
+			MmcmPtr->ClkOut1Div =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV6;
+			MmcmPtr->ClkOut2Div =
+				XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV6;
+		}
+		break;
+	case 8:
+		MmcmPtr->ClkFbOutMult =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT8;
+		MmcmPtr->DivClkDivide =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK8;
+		MmcmPtr->ClkOut0Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV8;
+		MmcmPtr->ClkOut1Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV8;
+		MmcmPtr->ClkOut2Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV8;
+		break;
+	case 10:
+		MmcmPtr->ClkFbOutMult =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT10;
+		MmcmPtr->DivClkDivide =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK10;
+		MmcmPtr->ClkOut0Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV10;
+		MmcmPtr->ClkOut1Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV10;
+		MmcmPtr->ClkOut2Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV10;
+		break;
+	case 12:
+		MmcmPtr->ClkFbOutMult =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT;
+		MmcmPtr->DivClkDivide =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK;
+		MmcmPtr->ClkOut0Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV;
+		MmcmPtr->ClkOut1Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV;
+		MmcmPtr->ClkOut2Div =
+			XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV;
+		break;
+	default:
+		break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function update/set the HDMI TX parameter.
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Ppc is the pixels per clock to set.
+* @param	Bpc is the bits per color to set.
+* @param	ColorFormat is the color format to set.
+*
+* @return
+*		- XST_SUCCESS if TX parameters set/updated.
+*		- XST_FAILURE if low resolution video not supported.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_SetHdmiTxParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId,
+		XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc,
+		XVidC_ColorFormat ColorFormat)
+{
+	u32 Status;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid((Ppc == (XVIDC_PPC_1)) || (Ppc == (XVIDC_PPC_2)) ||
+			(Ppc == (XVIDC_PPC_4)));
+	Xil_AssertNonvoid((Bpc == (XVIDC_BPC_8)) || (Bpc == (XVIDC_BPC_10)) ||
+			(Bpc == (XVIDC_BPC_12)) || (Bpc == (XVIDC_BPC_16)));
+	Xil_AssertNonvoid((ColorFormat == (XVIDC_CSF_RGB)) ||
+			(ColorFormat == (XVIDC_CSF_YCRCB_444)) ||
+			(ColorFormat == (XVIDC_CSF_YCRCB_422)) ||
+			(ColorFormat == (XVIDC_CSF_YCRCB_420)));
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	/* Only calculate the QPLL/CPLL parameters when the GT TX and RX are not
+	 * coupled. */
+    if (XHdmiphy1_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+        Status = XHdmiphy1_HdmiCpllParam(InstancePtr, QuadId, ChId,
+                XHDMIPHY1_DIR_TX);
+    }
+    else {
+        Status = XHdmiphy1_HdmiQpllParam(InstancePtr, QuadId, ChId,
+                XHDMIPHY1_DIR_TX);
+        /* Update SysClk and PLL Clk registers immediately. */
+        XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, QuadId);
+    }
+#else
+    Status = XHdmiphy1_HdmiTxPllParam(InstancePtr, QuadId, ChId);
+#endif
+
+    if (Status == XST_FAILURE) {
+        return Status;
+    }
+
+	/* Is HDMITXSS PPC match with HDMIPHY PPC? */
+	if (Ppc == InstancePtr->Config.Ppc) {
+		Status = (XST_SUCCESS);
+	}
+	else {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_PPC_MSMTCH_ERR, 1);
+		XHdmiphy1_ErrorHandler(InstancePtr);
+		Status = (XST_FAILURE);
+	}
+	if (Status == (XST_SUCCESS)) {
+		/* HDMI 2.1 */
+		if (InstancePtr->TxHdmi21Cfg.IsEnabled) {
+			XHdmiphy1_MmcmParam(InstancePtr, QuadId, XHDMIPHY1_DIR_TX);
+			return Status;
+		}
+
+		/* Calculate TXPLL parameters.
+		 * In HDMI the colordepth in YUV422 is always 12 bits,
+		 * although on the link itself it is being transmitted as
+		 * 8-bits. Therefore if the colorspace is YUV422, then force the
+		 * colordepth to 8 bits. */
+		if (ColorFormat == XVIDC_CSF_YCRCB_422) {
+			Status = XHdmiphy1_HdmiCfgCalcMmcmParam(InstancePtr, QuadId,
+                        ChId, XHDMIPHY1_DIR_TX, Ppc, XVIDC_BPC_8);
+		}
+		/* Other colorspaces. */
+		else {
+			Status = XHdmiphy1_HdmiCfgCalcMmcmParam(InstancePtr, QuadId,
+                        ChId, XHDMIPHY1_DIR_TX, Ppc, Bpc);
+		}
+	}
+	else {
+		Status = (XST_FAILURE);
+	}
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function update/set the HDMI RX parameter.
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if RX parameters set/updated.
+*		- XST_FAILURE if low resolution video not supported.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_SetHdmiRxParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	XHdmiphy1_ChannelId ChanId = ChId;
+	XHdmiphy1_PllType PllType;
+	u32 Status;
+	u64 DruCenterFreq;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	if (XHdmiphy1_IsRxUsingCpll(InstancePtr, QuadId, ChId)) {
+		Status = XHdmiphy1_HdmiCpllParam(InstancePtr, QuadId, ChId,
+                    XHDMIPHY1_DIR_RX);
+	}
+	else {
+        Status = XHdmiphy1_HdmiQpllParam(InstancePtr, QuadId, ChId,
+                    XHDMIPHY1_DIR_RX);
+		/* Update SysClk and PLL Clk registers immediately */
+		XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, QuadId);
+	}
+#else
+        Status = XHdmiphy1_HdmiRxPllParam(InstancePtr, QuadId, ChId);
+#endif
+
+	if (InstancePtr->HdmiRxDruIsEnabled) {
+		/* Determine PLL type. */
+		PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+                    XHDMIPHY1_CHANNEL_ID_CH1);
+		/* Update the ChId */
+		ChanId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+                    XHDMIPHY1_DIR_RX, PllType);
+
+		DruCenterFreq = XHdmiphy1_DruCalcCenterFreqHz(InstancePtr, QuadId,
+					ChanId);
+		XHdmiphy1_DruSetCenterFreqHz(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA,
+						DruCenterFreq);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function enables or disables the Pattern Generator for the GT Channel 4
+* when it isused to generate the TX TMDS Clock.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Enable TRUE/FALSE
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_PatgenEnable(XHdmiphy1 *InstancePtr, u8 QuadId, u8 Enable)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+    QuadId = QuadId;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+							XHDMIPHY1_PATGEN_CTRL_REG);
+
+	if (Enable) {
+		RegVal |= XHDMIPHY1_PATGEN_CTRL_ENABLE_MASK;
+	}
+	else {
+		RegVal &= ~XHDMIPHY1_PATGEN_CTRL_ENABLE_MASK;
+	}
+
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+						XHDMIPHY1_PATGEN_CTRL_REG, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the Pattern Generator for the GT Channel 4 when it is
+* used to generate the TX TMDS Clock.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	TxLineRate in Mbps.
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_PatgenSetRatio(XHdmiphy1 *InstancePtr, u8 QuadId,
+        u64 TxLineRate)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+    QuadId = QuadId;
+
+	RegVal = (XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_PATGEN_CTRL_REG)
+				& ~XHDMIPHY1_PATGEN_CTRL_RATIO_MASK);
+
+	if ((TxLineRate >= 3400) && (InstancePtr->HdmiTxSampleRate == 1)) {
+		RegVal |= XHDMIPHY1_Patgen_Ratio_40 &
+                        XHDMIPHY1_PATGEN_CTRL_RATIO_MASK;
+	}
+	else {
+		RegVal |= InstancePtr->HdmiTxSampleRate &
+						XHDMIPHY1_PATGEN_CTRL_RATIO_MASK;
+	}
+
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+						XHDMIPHY1_PATGEN_CTRL_REG, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the HDMIPHY to HDMI 2.0 mode
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if TX parameters set/updated.
+*		- XST_FAILURE if low resolution video not supported.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Hdmi20Config(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir)
+{
+	XHdmiphy1_PllType PllType;
+	u32 Status = XST_SUCCESS;
+
+	/* Suppress Warning Messages */
+    QuadId = QuadId;
+
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TMDS_RECONFIG, Dir);
+
+	/* Determine PLL type. */
+	PllType = XHdmiphy1_GetPllType(InstancePtr, 0, Dir,
+                XHDMIPHY1_CHANNEL_ID_CH1);
+
+	/* Update HDMI Configurations */
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		InstancePtr->TxHdmi21Cfg.LineRate = 0;
+		InstancePtr->TxHdmi21Cfg.NChannels = 0;
+		InstancePtr->TxHdmi21Cfg.IsEnabled = FALSE;
+	} else {
+		InstancePtr->RxHdmi21Cfg.LineRate = 0;
+		InstancePtr->RxHdmi21Cfg.NChannels = 0;
+		InstancePtr->RxHdmi21Cfg.IsEnabled = FALSE;
+	}
+
+	XHdmiphy1_MmcmSetClkinsel(InstancePtr, QuadId, Dir,
+			XHDMIPHY1_MMCM_CLKINSEL_CLKIN1);
+
+	/* Disable Clock Detector Interrupts */
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		XHdmiphy1_IntrEnable(InstancePtr,
+				XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE);
+	} else {
+		XHdmiphy1_IntrEnable(InstancePtr,
+				XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE);
+	}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	/* Update reference clock election. */
+	XHdmiphy1_CfgPllRefClkSel(InstancePtr, 0,
+		((PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+			XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA),
+		((Dir == XHDMIPHY1_DIR_TX) ?
+			InstancePtr->Config.TxRefClkSel :
+			InstancePtr->Config.RxRefClkSel));
+
+	/* Update RefClk selection. */
+	XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, 0);
+#else
+	/* Suppress Warning Messages */
+	PllType = PllType;
+#endif
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the GT for HDMI 2.1 operation
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if TX parameters set/updated.
+*		- XST_FAILURE if low resolution video not supported.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Hdmi21Config(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u64 LineRate, u8 NChannels)
+{
+	XHdmiphy1_PllType PllType;
+	u32 Status = XST_SUCCESS;
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4) || \
+	(XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	char SpeedGrade[5] = XPAR_HDMIPHY1_0_SPEEDGRADE_STR;
+	char CompVal[5] = "-1";
+	char *SpeedGradePtr = &SpeedGrade[0];
+	char *CompValPtr = &CompVal[0];
+
+	/* Look for -1 Parts. Max Line rate is 8Gbps */
+	if (strncmp(SpeedGradePtr, CompValPtr, 2) == 0) {
+		if (LineRate > 8e9) {
+			XHdmiphy1_LogWrite(InstancePtr,
+                XHDMIPHY1_LOG_EVT_SPDGRDE_ERR, Dir);
+			XHdmiphy1_ErrorHandler(InstancePtr);
+			return XST_FAILURE;
+		}
+	}
+#endif
+
+	XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_FRL_RECONFIG, Dir);
+
+	/* Determine PLL type. */
+	PllType = XHdmiphy1_GetPllType(InstancePtr, 0, Dir,
+                XHDMIPHY1_CHANNEL_ID_CH1);
+
+	/* Disable Clock Detector Interrupts */
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		if (InstancePtr->Config.TxRefClkSel !=
+				InstancePtr->Config.TxFrlRefClkSel) {
+			XHdmiphy1_IntrDisable(InstancePtr,
+					XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE);
+		}
+		/* Enable 4th Channel output */
+		XHdmiphy1_Clkout1OBufTdsEnable(InstancePtr, XHDMIPHY1_DIR_TX, (TRUE));
+	} else {
+		if (InstancePtr->Config.RxRefClkSel !=
+						InstancePtr->Config.RxFrlRefClkSel) {
+			XHdmiphy1_IntrDisable(InstancePtr,
+					XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE);
+		}
+	}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	/* Update reference clock election. */
+	XHdmiphy1_CfgPllRefClkSel(InstancePtr, 0,
+		((PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+			XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA),
+		((Dir == XHDMIPHY1_DIR_TX) ?
+			InstancePtr->Config.TxFrlRefClkSel :
+			InstancePtr->Config.RxFrlRefClkSel));
+
+	/* Update RefClk selection. */
+	XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, 0);
+#endif
+
+	/* Update HDMI Configurations */
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		InstancePtr->HdmiTxRefClkHz = XHDMIPHY1_HDMI21_FRL_REFCLK;
+		InstancePtr->TxHdmi21Cfg.LineRate = LineRate;
+		InstancePtr->TxHdmi21Cfg.NChannels = NChannels;
+		InstancePtr->TxHdmi21Cfg.IsEnabled = TRUE;
+
+		Status = XHdmiphy1_SetHdmiTxParam(InstancePtr, 0,
+				((PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+				XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA),
+				InstancePtr->Config.Ppc,
+				XVIDC_BPC_8,
+				XVIDC_CSF_RGB);
+
+		/* Mask the MMCM Lock */
+		XHdmiphy1_MmcmLockedMaskEnable(InstancePtr, 0, Dir, TRUE);
+
+		if (InstancePtr->Config.TxRefClkSel ==
+				InstancePtr->Config.TxFrlRefClkSel) {
+			XHdmiphy1_MmcmSetClkinsel(InstancePtr, QuadId, Dir,
+					XHDMIPHY1_MMCM_CLKINSEL_CLKIN1);
+		} else {
+			XHdmiphy1_MmcmSetClkinsel(InstancePtr, QuadId, Dir,
+					XHDMIPHY1_MMCM_CLKINSEL_CLKIN2);
+		}
+		if (InstancePtr->Config.TxRefClkSel !=
+				InstancePtr->Config.TxFrlRefClkSel) {
+			XHdmiphy1_HdmiTxTimerTimeoutHandler(InstancePtr);
+		}
+	} else {
+		InstancePtr->HdmiRxRefClkHz = XHDMIPHY1_HDMI21_FRL_REFCLK;
+		InstancePtr->RxHdmi21Cfg.LineRate = LineRate;
+		InstancePtr->RxHdmi21Cfg.NChannels = NChannels;
+		InstancePtr->RxHdmi21Cfg.IsEnabled = TRUE;
+
+		/* Set MMCM dividers for FRL mode */
+		XHdmiphy1_MmcmParam(InstancePtr, QuadId, XHDMIPHY1_DIR_RX);
+
+		/* Mask the MMCM Lock */
+		XHdmiphy1_MmcmLockedMaskEnable(InstancePtr, 0, Dir, TRUE);
+
+		if (InstancePtr->Config.RxRefClkSel !=
+				InstancePtr->Config.RxFrlRefClkSel) {
+			/* Set MMCM CLKINSEL to CLK2 */
+			XHdmiphy1_MmcmSetClkinsel(InstancePtr, QuadId, Dir,
+					XHDMIPHY1_MMCM_CLKINSEL_CLKIN2);
+
+			/* Start RX MMCM. */
+			XHdmiphy1_MmcmStart(InstancePtr, 0, XHDMIPHY1_DIR_RX);
+
+			XHdmiphy1_HdmiRxTimerTimeoutHandler(InstancePtr);
+		}
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function prints Video PHY debug information related to HDMI.
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	buff Buffer to print to
+* @param	buff_size Maximum size of buff
+*
+* @return	Number of characters printed in buff.
+*
+* @note		None.
+*
+******************************************************************************/
+
+int XHdmiphy1_HdmiDebugInfo(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, char *buff, int buff_size)
+{
+	int strSize = 0;
+	u32 RegValue;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_Channel *ChPtr;
+	XHdmiphy1_ChannelId CmnId = XHDMIPHY1_CHANNEL_ID_CMN0;
+	u8 CpllDVal;
+	u8 QpllDVal;
+	u8 UsesQpll0 = 0;
+
+	ChPtr = &InstancePtr->Quads[QuadId].Plls[0];
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+		if (XHdmiphy1_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: CPLL\n");
+		}
+		else {
+			if ((ChPtr->TxDataRefClkSel ==
+					XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL_OUTCLK) ||
+				(ChPtr->TxDataRefClkSel ==
+					XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK)) {
+				UsesQpll0 = (TRUE);
+				CmnId = XHDMIPHY1_CHANNEL_ID_CMN0;
+			}
+			else {
+				UsesQpll0 = (FALSE);
+				CmnId = XHDMIPHY1_CHANNEL_ID_CMN1;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: QPLL%d\n", (UsesQpll0 ? 0 : 1));
+		}
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+		if (XHdmiphy1_IsRxUsingCpll(InstancePtr, QuadId, ChId)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: CPLL\n");
+		}
+		else {
+			if ((ChPtr->RxDataRefClkSel ==
+					XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL_OUTCLK) ||
+				(ChPtr->RxDataRefClkSel ==
+					XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK)) {
+				UsesQpll0 = (TRUE);
+				CmnId = XHDMIPHY1_CHANNEL_ID_CMN0;
+			}
+			else {
+				UsesQpll0 = (FALSE);
+				CmnId = XHDMIPHY1_CHANNEL_ID_CMN1;
+			}
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: QPLL%d\n", (UsesQpll0 ? 0 : 1));
+		}
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"TX state: ");
+		switch (InstancePtr->Quads[QuadId].
+                    Plls[XHDMIPHY1_CH2IDX(ChId)].TxState) {
+		case (XHDMIPHY1_GT_STATE_IDLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"idle\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_LOCK):
+			if (XHdmiphy1_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"CPLL lock\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL%d lock\n", (UsesQpll0 ? 0 : 1));
+			}
+			break;
+		case (XHDMIPHY1_GT_STATE_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GT reset\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_ALIGN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,	
+				"align\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_READY):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ready\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"unknown\n");
+			break;
+		}
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"RX state: ");
+		switch (InstancePtr->Quads[QuadId].
+                    Plls[XHDMIPHY1_CH2IDX(ChId)].RxState) {
+		case (XHDMIPHY1_GT_STATE_IDLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"idle\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_LOCK):
+			if (XHdmiphy1_IsRxUsingCpll(InstancePtr, QuadId, ChId)) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"CPLL lock\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL%d lock\n", (UsesQpll0 ? 0 : 1));
+			}
+			break;
+		case (XHDMIPHY1_GT_STATE_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GT reset\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_READY):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ready\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"unknown\n");
+			break;
+		}
+	}
+
+	if (XHdmiphy1_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+		QpllDVal = ChPtr->RxOutDiv;
+		CpllDVal = ChPtr->TxOutDiv;
+	}
+	else {
+		CpllDVal = ChPtr->RxOutDiv;
+		QpllDVal = ChPtr->TxOutDiv;
+	}
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize, "\n");
+    if ((XHdmiphy1_IsTxUsingQpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX))) ||
+        (XHdmiphy1_IsRxUsingQpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)))) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"QPLL%d settings\n", (UsesQpll0 ? 0 : 1));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,	
+			"-------------\n" \
+			"M : %d - N : %d - D : %d\n\n",
+            InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(CmnId)].
+                PllParams.MRefClkDiv,
+            InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(CmnId)].
+                PllParams.NFbDiv, QpllDVal);
+	}
+
+    if ((XHdmiphy1_IsTxUsingCpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX))) ||
+        (XHdmiphy1_IsRxUsingCpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)))) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"CPLL settings\n" \
+				"-------------\n" \
+				"M : %d - N1 : %d - N2 : %d - D : %d\n\n",
+				ChPtr->PllParams.MRefClkDiv,
+				ChPtr->PllParams.N1FbDiv, ChPtr->PllParams.N2FbDiv,
+				CpllDVal);
+	}
+#else
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+		if (XHdmiphy1_IsTxUsingLcpll(InstancePtr, QuadId, ChId)) {
+			xil_printf("TX: LCPLL\r\n");
+		}
+		else {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: RPLL\n");
+		}
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+		if (XHdmiphy1_IsRxUsingLcpll(InstancePtr, QuadId, ChId)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: LCPLL\n");
+		}
+		else {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"RX: RPLL\n");
+		}
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"TX state: ");
+		switch (InstancePtr->Quads[QuadId].
+                    Plls[XHDMIPHY1_CH2IDX(ChId)].TxState) {
+		case (XHDMIPHY1_GT_STATE_IDLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"idle\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_GPO_RE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GPO Assert\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_LOCK):
+			if (XHdmiphy1_IsTxUsingLcpll(InstancePtr, QuadId, ChId)) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"LCPLL lock\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RPLL lock\n");
+			}
+			break;
+		case (XHDMIPHY1_GT_STATE_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GT reset\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_ALIGN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"align\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_READY):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ready\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"unknown\n");
+			break;
+		}
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+		xil_printf("RX state: ");
+		switch (InstancePtr->Quads[QuadId].
+                    Plls[XHDMIPHY1_CH2IDX(ChId)].RxState) {
+		case (XHDMIPHY1_GT_STATE_IDLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"idle\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_GPO_RE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GPO Assert\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_LOCK):
+			if (XHdmiphy1_IsRxUsingLcpll(InstancePtr, QuadId, ChId)) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"LCPLL lock\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RPLL lock\n");
+			}
+			break;
+		case (XHDMIPHY1_GT_STATE_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GT reset\n");
+			break;
+		case (XHDMIPHY1_GT_STATE_READY):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ready\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"unknown\n");
+			break;
+		}
+	}
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize, "\n");
+    if ((XHdmiphy1_IsTxUsingLcpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX))) ||
+        (XHdmiphy1_IsRxUsingLcpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)))) {
+            strSize += scnprintf(buff+strSize, buff_size-strSize,
+                "LCPLL settings\n" \
+                "-------------\n" \
+                "LR CFG : %d\n",
+            InstancePtr->Quads[QuadId].Lcpll.LineRateCfg);
+            strSize += scnprintf(buff+strSize, buff_size-strSize, "\n");
+    }
+
+    if ((XHdmiphy1_IsTxUsingRpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX))) ||
+        (XHdmiphy1_IsRxUsingRpll(InstancePtr, QuadId, ChId) &&
+            (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)))) {
+            strSize += scnprintf(buff+strSize, buff_size-strSize,
+                "RPLL settings\n" \
+                "-------------\n" \
+                "LR CFG : %d\n",
+            InstancePtr->Quads[QuadId].Rpll.LineRateCfg);
+            strSize += scnprintf(buff+strSize, buff_size-strSize, "\n");
+    }
+#endif
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"RX MMCM settings\n"
+			"-------------\n"
+			"Mult : %d - Div : %d - Clk0Div : %d - Clk1Div : %d - "
+			   "Clk2Div : %d\n\n",
+			InstancePtr->Quads[QuadId].RxMmcm.ClkFbOutMult,
+			InstancePtr->Quads[QuadId].RxMmcm.DivClkDivide,
+			InstancePtr->Quads[QuadId].RxMmcm.ClkOut0Div,
+			InstancePtr->Quads[QuadId].RxMmcm.ClkOut1Div,
+			InstancePtr->Quads[QuadId].RxMmcm.ClkOut2Div);
+	}
+
+	if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"TX MMCM settings\n" \
+			"-------------\n" \
+			"Mult : %d - Div : %d - Clk0Div : %d - Clk1Div : %d - "
+			   "Clk2Div : %d\n\n",
+			InstancePtr->Quads[QuadId].TxMmcm.ClkFbOutMult,
+			InstancePtr->Quads[QuadId].TxMmcm.DivClkDivide,
+			InstancePtr->Quads[QuadId].TxMmcm.ClkOut0Div,
+			InstancePtr->Quads[QuadId].TxMmcm.ClkOut1Div,
+			InstancePtr->Quads[QuadId].TxMmcm.ClkOut2Div);
+	}
+
+	if ((InstancePtr->Config.DruIsPresent) &&
+		(XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)))	{
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"DRU Settings\n" \
+			"-------------\n");
+		RegValue = XHdmiphy1_DruGetVersion(InstancePtr);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"Version  : %d\n", RegValue);
+
+		if (InstancePtr->HdmiRxDruIsEnabled) {
+			RegValue = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_DRU_GAIN_REG(ChId));
+
+
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"G1       : %d\nG1_P     : %d\n"
+				"G2       : %d\n",
+				((RegValue & XHDMIPHY1_DRU_GAIN_G1_MASK)),
+				((RegValue & XHDMIPHY1_DRU_GAIN_G1_P_MASK) >>
+					XHDMIPHY1_DRU_GAIN_G1_P_SHIFT),
+				((RegValue & XHDMIPHY1_DRU_GAIN_G2_MASK) >>
+					XHDMIPHY1_DRU_GAIN_G2_SHIFT));
+
+
+			RegValue = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_DRU_CFREQ_H_REG(ChId));
+
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Center_F : %x", RegValue);
+
+			RegValue = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_DRU_CFREQ_L_REG(ChId));
+
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"%x\n", RegValue);
+		}
+		else {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"DRU is disabled\n");
+		}
+
+		strSize += scnprintf(buff+strSize, buff_size-strSize," \n");
+	}
+	return strSize;
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+static const XHdmiphy1_GtHdmiChars Gthe4HdmiChars = {
+	.DruLineRate = XHDMIPHY1_HDMI_GTHE4_DRU_LRATE,
+	.PllScale = XHDMIPHY1_HDMI_GTHE4_PLL_SCALE,
+	.Qpll0RefClkMin = XHDMIPHY1_HDMI_GTHE4_QPLL0_REFCLK_MIN,
+	.Qpll1RefClkMin = XHDMIPHY1_HDMI_GTHE4_QPLL1_REFCLK_MIN,
+	.CpllRefClkMin = XHDMIPHY1_HDMI_GTHE4_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XHDMIPHY1_HDMI_GTHE4_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XHDMIPHY1_HDMI_GTHE4_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XHDMIPHY1_HDMI_GTHE4_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XHDMIPHY1_HDMI_GTHE4_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XHDMIPHY1_HDMI_GTHE4_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XHDMIPHY1_HDMI_GTHE4_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+static const XHdmiphy1_GtHdmiChars Gtye4HdmiChars = {
+	.DruLineRate = XHDMIPHY1_HDMI_GTYE4_DRU_LRATE,
+	.PllScale = XHDMIPHY1_HDMI_GTYE4_PLL_SCALE,
+	.Qpll0RefClkMin = XHDMIPHY1_HDMI_GTYE4_QPLL0_REFCLK_MIN,
+	.Qpll1RefClkMin = XHDMIPHY1_HDMI_GTYE4_QPLL1_REFCLK_MIN,
+	.CpllRefClkMin = XHDMIPHY1_HDMI_GTYE4_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XHDMIPHY1_HDMI_GTYE4_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XHDMIPHY1_HDMI_GTYE4_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XHDMIPHY1_HDMI_GTYE4_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XHDMIPHY1_HDMI_GTYE4_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XHDMIPHY1_HDMI_GTYE4_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XHDMIPHY1_HDMI_GTYE4_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+static const XHdmiphy1_GtHdmiChars Gtye5HdmiChars = {
+	.DruLineRate = XHDMIPHY1_HDMI_GTYE5_DRU_LRATE,
+	.PllScale = XHDMIPHY1_HDMI_GTYE5_PLL_SCALE,
+	.Qpll0RefClkMin = XHDMIPHY1_HDMI_GTYE5_LCPLL_REFCLK_MIN,
+	.Qpll1RefClkMin = XHDMIPHY1_HDMI_GTYE5_RPLL_REFCLK_MIN,
+	.CpllRefClkMin = 0,
+	.TxMmcmScale = XHDMIPHY1_HDMI_GTYE5_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XHDMIPHY1_HDMI_GTYE5_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XHDMIPHY1_HDMI_GTYE5_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XHDMIPHY1_HDMI_GTYE5_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XHDMIPHY1_HDMI_GTYE5_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XHDMIPHY1_HDMI_GTYE5_RX_MMCM_FVCO_MAX,
+};
+#endif
+
+/*****************************************************************************/
+/**
+* This function returns a pointer to the HDMI parameters based on the GT type.
+*
+* @param	InstancePtr is a pointer to the Hdmiphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- A pointer to the HDMI GT characteristics.
+*		- NULL if the GT type is unsupported.
+*
+* @note		None.
+*
+******************************************************************************/
+static const XHdmiphy1_GtHdmiChars *GetGtHdmiPtr(XHdmiphy1 *InstancePtr)
+{
+	/* Suppress Warning Messages */
+	InstancePtr = InstancePtr;
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTHE4)
+	return &Gthe4HdmiChars;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE4)
+	return &Gtye4HdmiChars;
+#elif (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+	return &Gtye5HdmiChars;
+#endif
+
+	return NULL;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hdmi.h
@@ -0,0 +1,253 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_hdmi.h
+ *
+ * The Xilinx HDMI PHY (HDMIPHY) driver. This driver supports the
+ * Xilinx HDMI PHY IP core.
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * 1.1   ku   24/07/20 Removed GTHE3 parameters
+ *                     Added MMCM parameters to support MAX Rate
+ * 1.2   ku   28/04/21 Updated Min Max limits for DRU Refclk
+ * </pre>
+ *
+ * @addtogroup xhdmiphy1_v2_2
+ * @{
+*******************************************************************************/
+
+#ifndef XHDMIPHY1_HDMI_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XHDMIPHY1_HDMI_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/************************** Constant Definitions ******************************/
+
+#define XHDMIPHY1_HDMI_GTYE5_DRU_LRATE           2500000000U
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK          200000000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK_MIN      199990000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK_MAX      200010000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK1         125000000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK1_MIN     124990000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK1_MAX     125010000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK2         400000000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK2_MIN     399980000LL
+#define XHDMIPHY1_HDMI_GTYE5_DRU_REFCLK2_MAX     400020000LL
+#define XHDMIPHY1_HDMI_GTYE5_PLL_SCALE           1000
+#define XHDMIPHY1_HDMI_GTYE5_LCPLL_REFCLK_MIN    120000000LL
+#define XHDMIPHY1_HDMI_GTYE5_RPLL_REFCLK_MIN     120000000LL
+#define XHDMIPHY1_HDMI_GTYE5_TX_MMCM_SCALE       1
+#define XHDMIPHY1_HDMI_GTYE5_TX_MMCM_FVCO_MIN    2160000000U
+#define XHDMIPHY1_HDMI_GTYE5_TX_MMCM_FVCO_MAX    4320000000U
+#define XHDMIPHY1_HDMI_GTYE5_RX_MMCM_SCALE       1
+#define XHDMIPHY1_HDMI_GTYE5_RX_MMCM_FVCO_MIN    2160000000U
+#define XHDMIPHY1_HDMI_GTYE5_RX_MMCM_FVCO_MAX    4320000000U
+
+#define XHDMIPHY1_HDMI_GTYE4_DRU_LRATE           2500000000U
+#define XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK          156250000LL
+#define XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK_MIN      156240000LL
+#define XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK_MAX      156260000LL
+#define XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK2         400000000LL
+#define XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK2_MIN     399980000LL
+#define XHDMIPHY1_HDMI_GTYE4_DRU_REFCLK2_MAX     400020000LL
+#define XHDMIPHY1_HDMI_GTYE4_PLL_SCALE           1000
+#define XHDMIPHY1_HDMI_GTYE4_QPLL0_REFCLK_MIN    61250000LL
+#define XHDMIPHY1_HDMI_GTYE4_QPLL1_REFCLK_MIN    50000000LL
+#define XHDMIPHY1_HDMI_GTYE4_CPLL_REFCLK_MIN     50000000LL
+#define XHDMIPHY1_HDMI_GTYE4_TX_MMCM_SCALE       1
+#define XHDMIPHY1_HDMI_GTYE4_TX_MMCM_FVCO_MIN    800000000U
+#define XHDMIPHY1_HDMI_GTYE4_TX_MMCM_FVCO_MAX    1600000000U
+#define XHDMIPHY1_HDMI_GTYE4_RX_MMCM_SCALE       1
+#define XHDMIPHY1_HDMI_GTYE4_RX_MMCM_FVCO_MIN    800000000U
+#define XHDMIPHY1_HDMI_GTYE4_RX_MMCM_FVCO_MAX    1600000000U
+
+#define XHDMIPHY1_HDMI_GTHE4_DRU_LRATE           2500000000U
+#define XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK          156250000LL
+#define XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK_MIN      156240000LL
+#define XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK_MAX      156260000LL
+#define XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK2         400000000LL
+#define XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK2_MIN     399980000LL
+#define XHDMIPHY1_HDMI_GTHE4_DRU_REFCLK2_MAX     400020000LL
+#define XHDMIPHY1_HDMI_GTHE4_PLL_SCALE           1000
+#define XHDMIPHY1_HDMI_GTHE4_QPLL0_REFCLK_MIN    61250000LL
+#define XHDMIPHY1_HDMI_GTHE4_QPLL1_REFCLK_MIN    50000000LL
+#define XHDMIPHY1_HDMI_GTHE4_CPLL_REFCLK_MIN     50000000LL
+#define XHDMIPHY1_HDMI_GTHE4_TX_MMCM_SCALE       1
+#define XHDMIPHY1_HDMI_GTHE4_TX_MMCM_FVCO_MIN    800000000U
+#define XHDMIPHY1_HDMI_GTHE4_TX_MMCM_FVCO_MAX    1600000000U
+#define XHDMIPHY1_HDMI_GTHE4_RX_MMCM_SCALE       1
+#define XHDMIPHY1_HDMI_GTHE4_RX_MMCM_FVCO_MIN    800000000U
+#define XHDMIPHY1_HDMI_GTHE4_RX_MMCM_FVCO_MAX    1600000000U
+
+/*
+ * Following are the MMCM Parameter values for each rate.
+ * Based on the MAX rate config in PHY the MMCM
+ * should be programmed to generate the vid clk in
+ * FRL mode
+ */
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/* 12 G -> (400 * 3/1) / 3 -> 400Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT		3
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK		1
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV	3
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV	3
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV	3
+
+/* 10 G -> 375Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT10 15
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK10 4
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV10 4
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV10 4
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV10 4
+
+/* 8 G -> 300Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT8 3
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK8 1
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV8 4
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV8 4
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV8 4
+
+/* 6x4 G -> 225Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT6 54
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK6 16
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV6 6
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV6 6
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV6 6
+
+/* 6x3 G -> 175Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT6x3 49
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK6x3 16
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV6x3 7
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV6x3 7
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV6x3 7
+
+/* 3x3 G -> 150Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT3x3 3
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK3x3 1
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV3x3 8
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV3x3 8
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV3x3 8
+
+#else
+/* 12 G -> (400 * 3/1) / 3 -> 400Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT		7
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK		1
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV	7
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV	7
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV	7
+
+/* 10 G -> 375Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT10 15
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK10 2
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV10 8
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV10 8
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV10 8
+
+/* 8 G -> 300Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT8 15
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK8 2
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV8 10
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV8 10
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV8 10
+
+/* 6x4 G -> 225Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT6 54
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK6 8
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV6 12
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV6 12
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV6 12
+
+/* 6x3 G -> 175Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT6x3 49
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK6x3 8
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV6x3 14
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV6x3 14
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV6x3 14
+
+/* 3x3 G -> 150Mhz */
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_FBOUTMULT3x3 15
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_DIVCLK3x3 2
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT0DIV3x3 20
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT1DIV3x3 20
+#define XHDMIPHY1_FRL_VIDCLK_MMCM_CLKOUT2DIV3x3 20
+
+#endif
+
+#define XHDMIPHY1_HDMI21_FRL_REFCLK              400000000U
+
+/**************************** Function Prototypes *****************************/
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+u32 XHdmiphy1_HdmiQpllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+u32 XHdmiphy1_HdmiCpllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_TxAlignReset(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Reset);
+void XHdmiphy1_TxAlignStart(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Start);
+#else
+u32 XHdmiphy1_HdmiTxPllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_HdmiRxPllParam(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+#endif
+void XHdmiphy1_ClkDetEnable(XHdmiphy1 *InstancePtr, u8 Enable);
+void XHdmiphy1_ClkDetTimerClear(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_ClkDetSetFreqLockThreshold(XHdmiphy1 *InstancePtr,
+        u16 ThresholdVal);
+u8 XHdmiphy1_ClkDetCheckFreqZero(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_ClkDetSetFreqTimeout(XHdmiphy1 *InstancePtr, u32 TimeoutVal);
+void XHdmiphy1_ClkDetTimerLoad(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u32 TimeoutVal);
+void XHdmiphy1_DruReset(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Reset);
+void XHdmiphy1_DruEnable(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 Enable);
+u16 XHdmiphy1_DruGetVersion(XHdmiphy1 *InstancePtr);
+void XHdmiphy1_DruSetCenterFreqHz(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_ChannelId ChId, u64 CenterFreqHz);
+u64 XHdmiphy1_DruCalcCenterFreqHz(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+void XHdmiphy1_HdmiGtDruModeEnable(XHdmiphy1 *InstancePtr, u8 Enable);
+void XHdmiphy1_PatgenSetRatio(XHdmiphy1 *InstancePtr,
+		u8 QuadId, u64 TxLineRate);
+void XHdmiphy1_PatgenEnable(XHdmiphy1 *InstancePtr, u8 QuadId, u8 Enable);
+void XHdmiphy1_HdmiIntrHandlerCallbackInit(XHdmiphy1 *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDMIPHY1_HDMI_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hdmi_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hdmi_intr.c
@@ -0,0 +1,1317 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_hdmi_intr.c
+ *
+ * This file contains video PHY functionality specific to the HDMI protocol
+ * related to interrupts.
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xstatus.h"
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+#include "xhdmiphy1_hdmi.h"
+#include "xhdmiphy1_gt.h"
+
+/************************** Function Prototypes ******************************/
+
+extern void XHdmiphy1_Ch2Ids(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+        u8 *Id0, u8 *Id1);
+
+static void XHdmiphy1_HdmiGtHandler(XHdmiphy1 *InstancePtr);
+static void XHdmiphy1_ClkDetHandler(XHdmiphy1 *InstancePtr);
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+* This function installs an HDMI callback function for the specified handler
+* type
+*
+* @param    InstancePtr is a pointer to the XHdmiphy1 instance.
+* @param    HandlerType is the interrupt handler type which specifies which
+*       interrupt event to attach the callback for.
+* @param    CallbackFunc is the address to the callback function.
+* @param    CallbackRef is the user data item that will be passed to the
+*       callback function when it is invoked.
+*
+* @return   None.
+*
+* @note     None.
+*
+*******************************************************************************/
+void XHdmiphy1_SetHdmiCallback(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_HdmiHandlerType HandlerType,
+        void *CallbackFunc, void *CallbackRef)
+{
+    /* Verify arguments. */
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid((HandlerType == XHDMIPHY1_HDMI_HANDLER_TXINIT) ||
+            (HandlerType == XHDMIPHY1_HDMI_HANDLER_TXREADY) ||
+            (HandlerType == XHDMIPHY1_HDMI_HANDLER_RXINIT) ||
+            (HandlerType == XHDMIPHY1_HDMI_HANDLER_RXREADY));
+    Xil_AssertVoid(CallbackFunc != NULL);
+    Xil_AssertVoid(CallbackRef != NULL);
+
+    switch (HandlerType) {
+    case XHDMIPHY1_HDMI_HANDLER_TXINIT:
+        InstancePtr->HdmiTxInitCallback = (XHdmiphy1_Callback)CallbackFunc;
+        InstancePtr->HdmiTxInitRef = CallbackRef;
+        break;
+
+    case XHDMIPHY1_HDMI_HANDLER_TXREADY:
+        InstancePtr->HdmiTxReadyCallback = (XHdmiphy1_Callback)CallbackFunc;
+        InstancePtr->HdmiTxReadyRef = CallbackRef;
+        break;
+
+    case XHDMIPHY1_HDMI_HANDLER_RXINIT:
+        InstancePtr->HdmiRxInitCallback = (XHdmiphy1_Callback)CallbackFunc;
+        InstancePtr->HdmiRxInitRef = CallbackRef;
+        break;
+
+    case XHDMIPHY1_HDMI_HANDLER_RXREADY:
+        InstancePtr->HdmiRxReadyCallback = (XHdmiphy1_Callback)CallbackFunc;
+        InstancePtr->HdmiRxReadyRef = CallbackRef;
+        break;
+
+    default:
+        break;
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function sets the appropriate HDMI interupt handlers.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiIntrHandlerCallbackInit(XHdmiphy1 *InstancePtr)
+{
+    /* GT Interrupts */
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_CPLL_LOCK,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_QPLL_LOCK,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_TXALIGN_DONE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_QPLL1_LOCK,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+#else
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+		XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+		XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+#endif
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_HdmiGtHandler, InstancePtr);
+
+    /* Clock Detector Interrupts */
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_ClkDetHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_ClkDetHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_ClkDetHandler, InstancePtr);
+
+    XHdmiphy1_SetIntrHandler(InstancePtr,
+            XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT,
+            (XHdmiphy1_IntrHandler)XHdmiphy1_ClkDetHandler, InstancePtr);
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by TX GPO Rising Edge.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiTxGpoRisingEdgeHandler(XHdmiphy1 *InstancePtr)
+{
+	u8 Id, Id0, Id1;
+	u8 CfgValComp;
+
+	/* Compare the current and next CFG values */
+	CfgValComp = XHdmiphy1_CheckLineRateCfg(InstancePtr, 0,
+						XHDMIPHY1_CHANNEL_ID_CH1,
+						XHDMIPHY1_DIR_TX);
+
+	if (CfgValComp) {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TXGPO_RE, 0);
+	} else {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TXGPO_RE, 1);
+	}
+
+	/* De-assert GPI port. */
+	XHdmiphy1_SetGpi(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+			 XHDMIPHY1_DIR_TX, FALSE);
+
+	/* Wait for GPO TX = 0 */
+	while (XHdmiphy1_GetGpo(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+				XHDMIPHY1_DIR_TX));
+
+	/* Start TX MMCM. */
+	XHdmiphy1_MmcmStart(InstancePtr, 0, XHDMIPHY1_DIR_TX);
+
+	/* Configure TXRATE Port */
+	XHdmiphy1_DirReconfig(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+			      XHDMIPHY1_DIR_TX);
+
+	/* Deassert reset on GT Reset IP TX */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_COMMON_INIT_REG,
+			   (XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					      XHDMIPHY1_COMMON_INIT_REG) & ~0x1));
+
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+			XHDMIPHY1_GT_STATE_LOCK;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by RX GPO Rising Edge.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiRxGpoRisingEdgeHandler(XHdmiphy1 *InstancePtr)
+{
+	u8 Id, Id0, Id1;
+	u8 CfgValComp;
+
+	/* Compare the current and next CFG values */
+	CfgValComp = XHdmiphy1_CheckLineRateCfg(InstancePtr, 0,
+						XHDMIPHY1_CHANNEL_ID_CH1, XHDMIPHY1_DIR_RX);
+
+	if (CfgValComp) {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RXGPO_RE, 0);
+	} else {
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RXGPO_RE, 1);
+	}
+
+	/* De-assert GPI port. */
+	XHdmiphy1_SetGpi(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+			 XHDMIPHY1_DIR_RX, FALSE);
+
+	/* Wait for GPO RX = 0 */
+	while (XHdmiphy1_GetGpo(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+				XHDMIPHY1_DIR_RX));
+
+	/* Configure RXRATE Port */
+	XHdmiphy1_DirReconfig(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+			      XHDMIPHY1_DIR_RX);
+
+	/* Deassert reset on GT Reset IP RX */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_COMMON_INIT_REG,
+			   (XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					      XHDMIPHY1_COMMON_INIT_REG) & ~0x2));
+
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+			XHDMIPHY1_GT_STATE_LOCK;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by LCPLL lock done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiLcpllLockHandler(XHdmiphy1 *InstancePtr)
+{
+	XHdmiphy1_PllType TxPllType;
+	u8 Id, Id0, Id1;
+	XHdmiphy1_ChannelId ChId;
+
+	/* Determine PLL type. */
+	TxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+					 XHDMIPHY1_CHANNEL_ID_CH1);
+
+	/* Determine which channel(s) to operate on. */
+	ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+				     XHDMIPHY1_DIR_NONE, XHDMIPHY1_PLL_TYPE_LCPLL);
+
+	if (XHdmiphy1_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+		/* Log, lock */
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_LCPLL_LOCK, 1);
+
+		XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0,
+				 &Id1);
+		for (Id = Id0; Id <= Id1; Id++) {
+			if (TxPllType == XHDMIPHY1_PLL_TYPE_LCPLL) {
+				InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+					TxState = XHDMIPHY1_GT_STATE_RESET;
+			}
+			else {
+				InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+					RxState = XHDMIPHY1_GT_STATE_RESET;
+			}
+		}
+	}
+	else {
+		/* Log, Lost lock */
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_LCPLL_LOCK, 0);
+	}
+
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by RPLL lock done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiRpllLockHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_PllType TxPllType;
+    u8 Id, Id0, Id1;
+    XHdmiphy1_ChannelId ChId;
+
+    /* Determine PLL type. */
+    TxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+        XHDMIPHY1_CHANNEL_ID_CH1);
+
+	/* Determine which channel(s) to operate on. */
+	ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+				XHDMIPHY1_DIR_NONE, XHDMIPHY1_PLL_TYPE_RPLL);
+
+	if (XHdmiphy1_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+		/* Log, lock */
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RPLL_LOCK, 1);
+
+        XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0,
+                &Id1);
+        for (Id = Id0; Id <= Id1; Id++) {
+        	if (TxPllType == XHDMIPHY1_PLL_TYPE_RPLL) {
+				InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+					TxState = XHDMIPHY1_GT_STATE_RESET;
+        	}
+        	else {
+				InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+					RxState = XHDMIPHY1_GT_STATE_RESET;
+        	}
+        }
+	}
+	else {
+		/* Log, Lost lock */
+		XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RPLL_LOCK, 0);
+	}
+
+}
+#else
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by QPLL lock done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiQpllLockHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_PllType TxPllType;
+    XHdmiphy1_PllType RxPllType;
+    u8 Id, Id0, Id1;
+    XHdmiphy1_ChannelId ChId;
+
+    /* Determine PLL type. */
+    TxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+        XHDMIPHY1_CHANNEL_ID_CH1);
+    RxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+        XHDMIPHY1_CHANNEL_ID_CH1);
+
+    /* RX is using QPLL. */
+    if ((RxPllType == XHDMIPHY1_PLL_TYPE_QPLL) ||
+            (RxPllType == XHDMIPHY1_PLL_TYPE_QPLL0) ||
+            (RxPllType == XHDMIPHY1_PLL_TYPE_QPLL1)) {
+
+        /* Determine which channel(s) to operate on. */
+        ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+                    XHDMIPHY1_DIR_RX, RxPllType);
+
+        if (XHdmiphy1_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+            /* Log, lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_QPLL_LOCK, 1);
+
+            /* GT RX reset. */
+            XHdmiphy1_ResetGtTxRx(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+                    XHDMIPHY1_DIR_RX, FALSE);
+
+            XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0,
+                    &Id1);
+            for (Id = Id0; Id <= Id1; Id++) {
+                InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+                    RxState = XHDMIPHY1_GT_STATE_RESET;
+            }
+        }
+        else {
+            /* Log, Lost lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_QPLL_LOCK, 0);
+        }
+    }
+    /* TX is using QPLL. */
+    else {
+        /* Determine which channel(s) to operate on. */
+        ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+                    XHDMIPHY1_DIR_TX, TxPllType);
+
+        if (XHdmiphy1_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+            /* Log, lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_QPLL_LOCK, 1);
+
+            /* GT TX reset. */
+            XHdmiphy1_ResetGtTxRx(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+                    XHDMIPHY1_DIR_TX, FALSE);
+
+            XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0,
+                    &Id1);
+            for (Id = Id0; Id <= Id1; Id++) {
+                InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+                    TxState = XHDMIPHY1_GT_STATE_RESET;
+            }
+        }
+        else {
+            /* Log, Lost lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_QPLL_LOCK, 0);
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by CPLL lock done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiCpllLockHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_PllType TxPllType;
+    XHdmiphy1_PllType RxPllType;
+    u8 Id, Id0, Id1;
+    XHdmiphy1_ChannelId ChId;
+
+    /* Determine PLL type. */
+    TxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+    RxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+
+    /* RX is using CPLL. */
+    if (RxPllType == XHDMIPHY1_PLL_TYPE_CPLL) {
+        /* Determine which channel(s) to operate on. */
+        ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+                    XHDMIPHY1_DIR_RX, RxPllType);
+
+        if (XHdmiphy1_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+            /* Log, lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_CPLL_LOCK, 1);
+            /* GT RX reset. */
+            XHdmiphy1_ResetGtTxRx(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+                    XHDMIPHY1_DIR_RX, FALSE);
+
+            for (Id = Id0; Id <= Id1; Id++) {
+                InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+                    RxState = XHDMIPHY1_GT_STATE_RESET;
+            }
+        }
+        else {
+            /* Log, Lost lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_CPLL_LOCK, 0);
+        }
+    }
+    /* TX is using CPLL. */
+    else {
+        /* Determine which channel(s) to operate on. */
+        ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0,
+                    XHDMIPHY1_DIR_TX, TxPllType);
+
+        if (XHdmiphy1_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+            /* Log, lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_CPLL_LOCK, 1);
+
+            /* GT TX reset. */
+            XHdmiphy1_ResetGtTxRx(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+                    XHDMIPHY1_DIR_TX, FALSE);
+
+            for (Id = Id0; Id <= Id1; Id++) {
+                InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].
+                    TxState = XHDMIPHY1_GT_STATE_RESET;
+            }
+        }
+        else {
+            /* Log, Lost lock */
+            XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_CPLL_LOCK, 0);
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GT TX alignment done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiGtTxAlignDoneLockHandler(XHdmiphy1 *InstancePtr)
+{
+    u8 Id, Id0, Id1;
+
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TX_ALIGN, 1);
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+            XHDMIPHY1_GT_STATE_READY;
+    }
+
+    /* TX ready callback. */
+    if (InstancePtr->HdmiTxReadyCallback) {
+        InstancePtr->HdmiTxReadyCallback(InstancePtr->HdmiTxReadyRef);
+    }
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GT TX reset lock done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiGtTxResetDoneLockHandler(XHdmiphy1 *InstancePtr)
+{
+    u8 Id, Id0, Id1;
+	XHdmiphy1_PllType PllType;
+    XHdmiphy1_ChannelId ChId;
+
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TX_RST_DONE, 0);
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+                       XHDMIPHY1_CHANNEL_ID_CH1);
+    /* Determine which channel(s) to operate on. */
+    ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+                PllType);
+
+    /* Set TX TMDS Clock Pattern Generator */
+    if ((InstancePtr->Config.UseGtAsTxTmdsClk == TRUE) &&
+         ((InstancePtr->TxHdmi21Cfg.IsEnabled == 0) ||
+         (InstancePtr->TxHdmi21Cfg.IsEnabled == 1 &&
+                InstancePtr->TxHdmi21Cfg.NChannels == 3))) {
+         XHdmiphy1_PatgenSetRatio(InstancePtr, 0,
+                       (u64)((XHdmiphy1_GetLineRateHz(InstancePtr,
+                                    0, ChId)) / 1000000));
+         XHdmiphy1_PatgenEnable(InstancePtr, 0, TRUE);
+    } else {
+         XHdmiphy1_PatgenEnable(InstancePtr, 0, FALSE);
+    }
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    if ((InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTHE4) ||
+        (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTYE4)) {
+        XHdmiphy1_TxAlignReset(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, TRUE);
+        XHdmiphy1_TxAlignReset(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, FALSE);
+    }
+
+    /* GT alignment. */
+    XHdmiphy1_TxAlignStart(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, TRUE);
+    XHdmiphy1_TxAlignStart(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, FALSE);
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+            XHDMIPHY1_GT_STATE_ALIGN;
+    }
+#else
+	/* Deassert TX LNKRDY MASK */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_TX_INIT_REG,
+			(XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_TX_INIT_REG) & ~0x10101010));
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+        	XHDMIPHY1_GT_STATE_READY;
+    }
+
+    /* TX ready callback. */
+    if (InstancePtr->HdmiTxReadyCallback) {
+        InstancePtr->HdmiTxReadyCallback(InstancePtr->HdmiTxReadyRef);
+    }
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GT RX reset lock done.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiGtRxResetDoneLockHandler(XHdmiphy1 *InstancePtr)
+{
+    u8 Id, Id0, Id1;
+
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RX_RST_DONE, 0);
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+            XHDMIPHY1_GT_STATE_READY;
+    }
+
+	/* Deassert RX LNKRDY MASK */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_RX_INIT_REG,
+			(XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_RX_INIT_REG) & ~0x10101010));
+
+    /* If DRU is use/d, release its reset. */
+    if (InstancePtr->HdmiRxDruIsEnabled) {
+        XHdmiphy1_DruReset(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, FALSE);
+    }
+
+    /* RX ready callback. */
+    if (InstancePtr->HdmiRxReadyCallback) {
+        InstancePtr->HdmiRxReadyCallback(InstancePtr->HdmiRxReadyRef);
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by a change in TX frequency
+* as detected by the HDMI clock detector logic.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiTxClkDetFreqChangeHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_PllType PllType;
+    u8 Id, Id0, Id1;
+
+    if (InstancePtr->TxHdmi21Cfg.IsEnabled) {
+        if (InstancePtr->Config.TxRefClkSel !=
+                InstancePtr->Config.TxFrlRefClkSel) {
+            return;
+        }
+    }
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TX_FREQ, 0);
+
+	/* Set TX TMDS Clock Pattern Generator */
+	if ((InstancePtr->Config.UseGtAsTxTmdsClk == TRUE) &&
+		((InstancePtr->TxHdmi21Cfg.IsEnabled == 0) ||
+		 (InstancePtr->TxHdmi21Cfg.IsEnabled == 1 &&
+			InstancePtr->TxHdmi21Cfg.NChannels == 3))) {
+		XHdmiphy1_PatgenEnable(InstancePtr, 0, FALSE);
+	}
+
+	/* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+
+	/* If the TX frequency has changed, the PLL is always disabled. */
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    XHdmiphy1_PowerDownGtPll(InstancePtr, 0,
+        (PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+        XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA, TRUE);
+
+    XHdmiphy1_ResetGtPll(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_TX, TRUE);
+#else
+	/* Suppress Warning Messages */
+    PllType = PllType;
+
+    /* Mask RESET DONE */
+	/* Deassert TX LNKRDY MASK */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_TX_INIT_REG,
+			(XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_TX_INIT_REG) | 0x10101010));
+#endif
+    /* Mask the MMCM Lock */
+    XHdmiphy1_MmcmLockedMaskEnable(InstancePtr, 0, XHDMIPHY1_DIR_TX, TRUE);
+
+    /* Disable TX MMCM. */
+    /* XHdmiphy1_MmcmPowerDown(InstancePtr, 0, XHDMIPHY1_DIR_TX, TRUE); */
+
+    /* Clear TX timer. */
+    XHdmiphy1_ClkDetTimerClear(InstancePtr, 0, XHDMIPHY1_DIR_TX);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    /* Clear GT alignment. */
+    XHdmiphy1_TxAlignStart(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, FALSE);
+#endif
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+            XHDMIPHY1_GT_STATE_IDLE;
+    }
+
+    /* If there is no reference clock, load TX timer in usec. */
+    if (XHdmiphy1_ClkDetGetRefClkFreqHz(InstancePtr, XHDMIPHY1_DIR_TX)) {
+        XHdmiphy1_ClkDetTimerLoad(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+                        InstancePtr->Config.AxiLiteClkFreq/1000);
+    }
+
+    /* Callback to re-initialize. */
+    if (InstancePtr->HdmiTxInitCallback) {
+        InstancePtr->HdmiTxInitCallback(InstancePtr->HdmiTxInitRef);
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by a change in RX frequency
+* as detected by the HDMI clock detector logic.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiRxClkDetFreqChangeHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_PllType PllType;
+    u32 RxRefClkHz;
+    u8 Id, Id0, Id1;
+
+    if (InstancePtr->RxHdmi21Cfg.IsEnabled) {
+        if (InstancePtr->Config.RxRefClkSel !=
+                InstancePtr->Config.RxFrlRefClkSel) {
+            return;
+        }
+    }
+
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RX_FREQ, 0);
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+            XHDMIPHY1_GT_STATE_IDLE;
+    }
+
+    if (!InstancePtr->RxHdmi21Cfg.IsEnabled) {
+        /* Mask the MMCM Lock */
+        XHdmiphy1_MmcmLockedMaskEnable(InstancePtr, 0, XHDMIPHY1_DIR_RX, TRUE);
+    }
+
+    /* Determine PLL type and RX reference clock selection. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+
+    /* Fetch New RX Reference Clock Frequency */
+    RxRefClkHz = XHdmiphy1_ClkDetGetRefClkFreqHz(InstancePtr,
+                    XHDMIPHY1_DIR_RX);
+
+    /* Round input frequency to 10 kHz. */
+    RxRefClkHz = (RxRefClkHz+5000) / 10000;
+    RxRefClkHz = RxRefClkHz * 10000;
+
+    /* Store RX reference clock. */
+    if (InstancePtr->RxHdmi21Cfg.IsEnabled) {
+        InstancePtr->HdmiRxRefClkHz = XHDMIPHY1_HDMI21_FRL_REFCLK;
+    }
+    else {
+        InstancePtr->HdmiRxRefClkHz = RxRefClkHz;
+    }
+
+    /* If the RX frequency has changed, the PLL is always disabled. */
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    XHdmiphy1_PowerDownGtPll(InstancePtr, 0,
+        (PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+        XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA, TRUE);
+
+    XHdmiphy1_ResetGtPll(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+        XHDMIPHY1_DIR_RX, TRUE);
+#else
+	/* Suppress Warning Messages */
+    PllType = PllType;
+
+    /* Mask RESET DONE */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_RX_INIT_REG,
+			(XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_RX_INIT_REG) | 0x10101010));
+
+#endif
+
+    /* If DRU is present, disable it and assert reset. */
+    if (InstancePtr->Config.DruIsPresent) {
+        XHdmiphy1_DruReset(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, TRUE);
+        XHdmiphy1_DruEnable(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, FALSE);
+    }
+
+    /* Clear RX timer. */
+    XHdmiphy1_ClkDetTimerClear(InstancePtr, 0, XHDMIPHY1_DIR_RX);
+
+    /* If there is reference clock, load RX timer in usec.
+     * The reference clock should be larger than 25Mhz. We are using a 20Mhz
+     * instead to keep some margin for errors. */
+    if (RxRefClkHz > 20000000) {
+        XHdmiphy1_ClkDetTimerLoad(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+                        InstancePtr->Config.AxiLiteClkFreq/1000);
+
+        /* Callback to re-initialize. */
+        if (InstancePtr->HdmiRxInitCallback) {
+            InstancePtr->HdmiRxInitCallback(InstancePtr->HdmiRxInitRef);
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for TX timer timeout events.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiTxTimerTimeoutHandler(XHdmiphy1 *InstancePtr)
+{
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    XHdmiphy1_ChannelId ChId;
+    XHdmiphy1_PllType PllType;
+#else
+	u8 CfgValComp;
+#endif
+    u8 Id, Id0, Id1;
+
+    if (!InstancePtr->TxHdmi21Cfg.IsEnabled) {
+        XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TX_TMR, 1);
+    }
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+    /* Determine which channel(s) to operate on. */
+    ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0, XHDMIPHY1_DIR_TX, PllType);
+
+    /* Start TX MMCM. */
+    XHdmiphy1_MmcmStart(InstancePtr, 0, XHDMIPHY1_DIR_TX);
+
+    /* Enable PLL. */
+    XHdmiphy1_PowerDownGtPll(InstancePtr, 0,
+        (PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+        XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA, FALSE);
+
+    if (PllType != XHDMIPHY1_PLL_TYPE_CPLL) {
+        /* Set QPLL Selection in PIO. */
+        XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, 0);
+    }
+
+    XHdmiphy1_ClkReconfig(InstancePtr, 0, ChId);
+    XHdmiphy1_OutDivReconfig(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_TX);
+    if ((InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTHE4) ||
+        (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTYE4)) {
+        XHdmiphy1_SetBufgGtDiv(InstancePtr, XHDMIPHY1_DIR_TX,
+                (PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+                InstancePtr->Quads[0].Plls[0].TxOutDiv :
+                (InstancePtr->Quads[0].Plls[0].TxOutDiv != 16) ?
+                        InstancePtr->Quads[0].Plls[0].TxOutDiv :
+                        InstancePtr->Quads[0].Plls[0].TxOutDiv / 2);
+    }
+
+    XHdmiphy1_DirReconfig(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+        XHDMIPHY1_DIR_TX);
+
+    /* Assert PLL reset. */
+    XHdmiphy1_ResetGtPll(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_TX, TRUE);
+
+    /* De-assert PLL reset. */
+    XHdmiphy1_ResetGtPll(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_TX, FALSE);
+
+    if ((InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTHE4) ||
+        (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTYE4)) {
+        /* Clear GT alignment. */
+        XHdmiphy1_TxAlignStart(InstancePtr, ChId, FALSE);
+    }
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+            XHDMIPHY1_GT_STATE_LOCK;
+    }
+#else
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].TxState =
+            XHDMIPHY1_GT_STATE_GPO_RE;
+    }
+
+    /* Compare the current and next CFG values */
+	CfgValComp = XHdmiphy1_CheckLineRateCfg(InstancePtr, 0,
+					XHDMIPHY1_CHANNEL_ID_CH1, XHDMIPHY1_DIR_TX);
+
+	if (!CfgValComp) {
+		/* Assert GPI port. */
+		XHdmiphy1_SetGpi(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+				XHDMIPHY1_DIR_TX, TRUE);
+	}
+	else {
+		XHdmiphy1_HdmiTxGpoRisingEdgeHandler(InstancePtr);
+	}
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for RX timer timeout events.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiRxTimerTimeoutHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_ChannelId ChId;
+    XHdmiphy1_PllType PllType;
+    u32 Status;
+    u8 Id, Id0, Id1;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+	u8 CfgValComp;
+#endif
+
+    if (!InstancePtr->RxHdmi21Cfg.IsEnabled) {
+        XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RX_TMR, 1);
+    } else {
+		if (InstancePtr->Config.RxRefClkSel ==
+				InstancePtr->Config.RxFrlRefClkSel) {
+			/* Set MMCM CLKINSEL to CLK1 */
+			XHdmiphy1_MmcmSetClkinsel(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+					XHDMIPHY1_MMCM_CLKINSEL_CLKIN1);
+
+			/* Start RX MMCM. */
+			XHdmiphy1_MmcmStart(InstancePtr, 0, XHDMIPHY1_DIR_RX);
+		}
+    }
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+    /* Determine which channel(s) to operate on. */
+    ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0, XHDMIPHY1_DIR_RX, PllType);
+
+    XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+
+
+    /* Set RX parameters. */
+    Status = XHdmiphy1_SetHdmiRxParam(InstancePtr, 0, ChId);
+    if (Status != XST_SUCCESS) {
+        for (Id = Id0; Id <= Id1; Id++) {
+            InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+                XHDMIPHY1_GT_STATE_IDLE;
+        }
+
+        return;
+    }
+
+    /* Enable DRU to set the clock muxes. */
+    XHdmiphy1_DruEnable(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA,
+            InstancePtr->HdmiRxDruIsEnabled);
+
+    /* Update GT DRU mode. */
+    XHdmiphy1_HdmiGtDruModeEnable(InstancePtr,
+    		InstancePtr->HdmiRxDruIsEnabled);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    /* Enable PLL. */
+    XHdmiphy1_PowerDownGtPll(InstancePtr, 0,
+        (PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+        XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA, FALSE);
+
+    /* Update reference clock election. */
+    if (InstancePtr->RxHdmi21Cfg.IsEnabled == FALSE) {
+        XHdmiphy1_CfgPllRefClkSel(InstancePtr, 0,
+            ((PllType == XHDMIPHY1_PLL_TYPE_CPLL) ?
+                XHDMIPHY1_CHANNEL_ID_CHA : XHDMIPHY1_CHANNEL_ID_CMNA),
+            ((InstancePtr->HdmiRxDruIsEnabled) ?
+                InstancePtr->Config.DruRefClkSel :
+                InstancePtr->Config.RxRefClkSel));
+    }
+
+    /* Update RefClk selection. */
+    XHdmiphy1_WriteCfgRefClkSelReg(InstancePtr, 0);
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+    /* Determine which channel(s) to operate on. */
+    ChId = XHdmiphy1_GetRcfgChId(InstancePtr, 0, XHDMIPHY1_DIR_RX, PllType);
+
+    XHdmiphy1_ClkReconfig(InstancePtr, 0, ChId);
+    XHdmiphy1_OutDivReconfig(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_RX);
+
+    XHdmiphy1_DirReconfig(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+        XHDMIPHY1_DIR_RX);
+
+    /* Assert RX PLL reset. */
+    XHdmiphy1_ResetGtPll(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+        XHDMIPHY1_DIR_RX, TRUE);
+
+    /* De-assert RX PLL reset. */
+    XHdmiphy1_ResetGtPll(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+            XHDMIPHY1_DIR_RX, FALSE);
+
+    for (Id = Id0; Id <= Id1; Id++) {
+            InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+			XHDMIPHY1_GT_STATE_LOCK;
+    }
+
+
+#else
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+    for (Id = Id0; Id <= Id1; Id++) {
+        InstancePtr->Quads[0].Plls[XHDMIPHY1_CH2IDX(Id)].RxState =
+            XHDMIPHY1_GT_STATE_GPO_RE;
+    }
+
+    /* Compare the current and next CFG values */
+	CfgValComp = XHdmiphy1_CheckLineRateCfg(InstancePtr, 0,
+					XHDMIPHY1_CHANNEL_ID_CH1, XHDMIPHY1_DIR_RX);
+
+	if (!CfgValComp) {
+		/* Assert GPI port. */
+		XHdmiphy1_SetGpi(InstancePtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+				XHDMIPHY1_DIR_RX, TRUE);
+	}
+	else {
+		XHdmiphy1_HdmiRxGpoRisingEdgeHandler(InstancePtr);
+	}
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for TX MMCM Lock events.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiTxMmcmLockHandler(XHdmiphy1 *InstancePtr)
+{
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_TXPLL_LOCK, 1);
+
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for RX MMCM Lock events.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiRxMmcmLockHandler(XHdmiphy1 *InstancePtr)
+{
+
+    XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_RXPLL_LOCK, 1);
+
+}
+
+/*****************************************************************************/
+/**
+* This function is the interrupt handler for the GT events.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_HdmiGtHandler(XHdmiphy1 *InstancePtr)
+{
+    u32 Event;
+    u32 EventMask;
+    u32 EventAck;
+    XHdmiphy1_GtState *TxStatePtr;
+    XHdmiphy1_GtState *RxStatePtr;
+    XHdmiphy1_PllType TxPllType;
+    XHdmiphy1_PllType RxPllType;
+
+
+    EventMask =
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHDMIPHY1_INTR_QPLL0_LOCK_MASK | XHDMIPHY1_INTR_CPLL_LOCK_MASK |
+		XHDMIPHY1_INTR_QPLL1_LOCK_MASK |
+		XHDMIPHY1_INTR_TXALIGNDONE_MASK |
+#else
+		XHDMIPHY1_INTR_LCPLL_LOCK_MASK | XHDMIPHY1_INTR_RPLL_LOCK_MASK |
+        XHDMIPHY1_INTR_TXGPO_RE_MASK | XHDMIPHY1_INTR_RXGPO_RE_MASK |
+#endif
+		XHDMIPHY1_INTR_TXRESETDONE_MASK | XHDMIPHY1_INTR_RXRESETDONE_MASK |
+		XHDMIPHY1_INTR_TXMMCMUSRCLK_LOCK_MASK |
+        XHDMIPHY1_INTR_RXMMCMUSRCLK_LOCK_MASK;
+
+    u8 QuadId = 0;
+
+    /* Read Interrupt Status register */
+    Event = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+                XHDMIPHY1_INTR_STS_REG);
+
+    EventAck = EventMask & Event;
+
+    /* Read States for Quad=0 Ch1 */
+    TxStatePtr = &InstancePtr->Quads[QuadId].Ch1.TxState;
+    RxStatePtr = &InstancePtr->Quads[QuadId].Ch1.RxState;
+
+    /* Determine PLL type. */
+    TxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_TX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+    RxPllType = XHdmiphy1_GetPllType(InstancePtr, 0, XHDMIPHY1_DIR_RX,
+            XHDMIPHY1_CHANNEL_ID_CH1);
+
+    if (Event & XHDMIPHY1_INTR_TXMMCMUSRCLK_LOCK_MASK) {
+        XHdmiphy1_HdmiTxMmcmLockHandler(InstancePtr);
+    }
+    if (Event & XHDMIPHY1_INTR_RXMMCMUSRCLK_LOCK_MASK) {
+        XHdmiphy1_HdmiRxMmcmLockHandler(InstancePtr);
+    }
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+    if ((Event & XHDMIPHY1_INTR_QPLL0_LOCK_MASK) ||
+        (Event & XHDMIPHY1_INTR_QPLL1_LOCK_MASK)) {
+        XHdmiphy1_HdmiQpllLockHandler(InstancePtr);
+    }
+    if (Event & XHDMIPHY1_INTR_CPLL_LOCK_MASK) {
+        XHdmiphy1_HdmiCpllLockHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_TXRESETDONE_MASK)
+            && (*TxStatePtr == XHDMIPHY1_GT_STATE_RESET)) {
+        XHdmiphy1_HdmiGtTxResetDoneLockHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_TXALIGNDONE_MASK)
+            && (*TxStatePtr == XHDMIPHY1_GT_STATE_ALIGN)) {
+        XHdmiphy1_HdmiGtTxAlignDoneLockHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_RXRESETDONE_MASK)
+            && (*RxStatePtr == XHDMIPHY1_GT_STATE_RESET)) {
+        XHdmiphy1_HdmiGtRxResetDoneLockHandler(InstancePtr);
+    }
+
+	/* Suppress Warning Messages */
+    TxPllType = TxPllType;
+    RxPllType = RxPllType;
+#else
+    if (Event & XHDMIPHY1_INTR_TXGPO_RE_MASK) {
+        XHdmiphy1_HdmiTxGpoRisingEdgeHandler(InstancePtr);
+    }
+    if (Event & XHDMIPHY1_INTR_RXGPO_RE_MASK) {
+	XHdmiphy1_HdmiRxGpoRisingEdgeHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_LCPLL_LOCK_MASK) &&
+		(((*TxStatePtr != XHDMIPHY1_GT_STATE_IDLE) &&
+				(TxPllType == XHDMIPHY1_PLL_TYPE_LCPLL)) ||
+			 ((*RxStatePtr != XHDMIPHY1_GT_STATE_IDLE) &&
+					(RxPllType == XHDMIPHY1_PLL_TYPE_LCPLL)))) {
+        XHdmiphy1_HdmiLcpllLockHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_RPLL_LOCK_MASK) &&
+		(((*TxStatePtr != XHDMIPHY1_GT_STATE_IDLE) &&
+				(TxPllType == XHDMIPHY1_PLL_TYPE_RPLL)) ||
+			 ((*RxStatePtr != XHDMIPHY1_GT_STATE_IDLE) &&
+					(RxPllType == XHDMIPHY1_PLL_TYPE_RPLL)))) {
+        XHdmiphy1_HdmiRpllLockHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_TXRESETDONE_MASK)
+        && (*TxStatePtr == XHDMIPHY1_GT_STATE_RESET)) {
+        XHdmiphy1_HdmiGtTxResetDoneLockHandler(InstancePtr);
+    }
+    if ((Event & XHDMIPHY1_INTR_RXRESETDONE_MASK)
+        && (*RxStatePtr == XHDMIPHY1_GT_STATE_RESET)) {
+        XHdmiphy1_HdmiGtRxResetDoneLockHandler(InstancePtr);
+    }
+
+	/* Suppress Warning Messages */
+    TxStatePtr = TxStatePtr;
+    RxStatePtr = RxStatePtr;
+#endif
+
+    /* Clear event flags by writing to Interrupt Status register */
+    XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_INTR_STS_REG,
+            EventAck);
+}
+
+/*****************************************************************************/
+/**
+* This function is the interrupt handler for the clock detector events.
+*
+* @param    InstancePtr is a pointer to the HDMIPHY instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XHdmiphy1_ClkDetHandler(XHdmiphy1 *InstancePtr)
+{
+    u32 Event;
+    u32 EventMask;
+    u32 EventAck;
+
+    EventMask = XHDMIPHY1_INTR_TXCLKDETFREQCHANGE_MASK |
+                XHDMIPHY1_INTR_RXCLKDETFREQCHANGE_MASK |
+                XHDMIPHY1_INTR_TXTMRTIMEOUT_MASK |
+                XHDMIPHY1_INTR_RXTMRTIMEOUT_MASK;
+
+    /* Read Interrupt Status register */
+    Event = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+                XHDMIPHY1_INTR_STS_REG);
+
+    EventAck = EventMask & Event;
+
+    if (Event & XHDMIPHY1_INTR_TXCLKDETFREQCHANGE_MASK) {
+        XHdmiphy1_HdmiTxClkDetFreqChangeHandler(InstancePtr);
+    }
+    if (Event & XHDMIPHY1_INTR_RXCLKDETFREQCHANGE_MASK) {
+        XHdmiphy1_HdmiRxClkDetFreqChangeHandler(InstancePtr);
+    }
+    if (Event & XHDMIPHY1_INTR_TXTMRTIMEOUT_MASK) {
+        XHdmiphy1_HdmiTxTimerTimeoutHandler(InstancePtr);
+    }
+    if (Event & XHDMIPHY1_INTR_RXTMRTIMEOUT_MASK) {
+        XHdmiphy1_HdmiRxTimerTimeoutHandler(InstancePtr);
+    }
+
+    /* Clear event flags by writing to Interrupt Status register */
+    XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_INTR_STS_REG,
+            EventAck);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_hw.h
@@ -0,0 +1,697 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_hw.h
+ *
+ * This header file contains the identifiers and low-level driver functions (or
+ * macros) that can be used to access the device. High-level driver functions
+ * are defined in xhdmiphy1.h.
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+ * @addtogroup xhdmiphy1_v2_2
+ * @{
+*******************************************************************************/
+
+#ifndef XHDMIPHY1_HW_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XHDMIPHY1_HW_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files **********************************/
+
+#include "xil_io.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions ******************************/
+
+/******************************************************************************/
+/**
+ * Address mapping for the Video PHY core.
+ *
+*******************************************************************************/
+/** @name HDMIPHY core registers: General registers.
+  * @{
+  */
+#define XHDMIPHY1_VERSION_REG            0x000
+#define XHDMIPHY1_BANK_SELECT_REG        0x00C
+#define XHDMIPHY1_REF_CLK_SEL_REG        0x010
+#define XHDMIPHY1_PLL_RESET_REG          0x014
+#define XHDMIPHY1_COMMON_INIT_REG        0x014
+#define XHDMIPHY1_PLL_LOCK_STATUS_REG    0x018
+#define XHDMIPHY1_TX_INIT_REG            0x01C
+#define XHDMIPHY1_TX_INIT_STATUS_REG     0x020
+#define XHDMIPHY1_RX_INIT_REG            0x024
+#define XHDMIPHY1_RX_INIT_STATUS_REG     0x028
+#define XHDMIPHY1_IBUFDS_GTXX_CTRL_REG   0x02C
+#define XHDMIPHY1_POWERDOWN_CONTROL_REG  0x030
+#define XHDMIPHY1_LOOPBACK_CONTROL_REG   0x038
+/* @} */
+
+/** @name HDMIPHY core registers: Dynamic reconfiguration port (DRP) registers.
+  * @{
+  */
+#define XHDMIPHY1_DRP_CONTROL_CH1_REG    0x040
+#define XHDMIPHY1_DRP_CONTROL_CH2_REG    0x044
+#define XHDMIPHY1_DRP_CONTROL_CH3_REG    0x048
+#define XHDMIPHY1_DRP_CONTROL_CH4_REG    0x04C
+#define XHDMIPHY1_DRP_STATUS_CH1_REG     0x050
+#define XHDMIPHY1_DRP_STATUS_CH2_REG     0x054
+#define XHDMIPHY1_DRP_STATUS_CH3_REG     0x058
+#define XHDMIPHY1_DRP_STATUS_CH4_REG     0x05C
+#define XHDMIPHY1_DRP_CONTROL_COMMON_REG 0x060
+#define XHDMIPHY1_DRP_STATUS_COMMON_REG  0x064
+#define XHDMIPHY1_DRP_CONTROL_TXMMCM_REG 0x124
+#define XHDMIPHY1_DRP_STATUS_TXMMCM_REG  0x128
+#define XHDMIPHY1_DRP_CONTROL_RXMMCM_REG 0x144
+#define XHDMIPHY1_DRP_STATUS_RXMMCM_REG  0x148
+/* @} */
+
+/** @name HDMIPHY core registers: CPLL Calibration registers.
+  * @{
+  */
+#define XHDMIPHY1_CPLL_CAL_PERIOD_REG    0x068
+#define XHDMIPHY1_CPLL_CAL_TOL_REG       0x06C
+/* @} */
+/** @name HDMIPHY core registers: GT Debug INTF registers.
+  * @{
+  */
+#define XHDMIPHY1_GT_DBG_GPI_REG         0x068
+#define XHDMIPHY1_GT_DBG_GPO_REG         0x06C
+/* @} */
+
+/** @name HDMIPHY core registers: Transmitter function registers.
+  * @{
+  */
+#define XHDMIPHY1_TX_CONTROL_REG         0x070
+#define XHDMIPHY1_TX_BUFFER_BYPASS_REG   0x074
+#define XHDMIPHY1_TX_STATUS_REG          0x078
+#define XHDMIPHY1_TX_DRIVER_CH12_REG     0x07C
+#define XHDMIPHY1_TX_DRIVER_CH34_REG     0x080
+#define XHDMIPHY1_TX_DRIVER_EXT_REG      0x084
+#define XHDMIPHY1_TX_RATE_CH12_REG       0x08C
+#define XHDMIPHY1_TX_RATE_CH34_REG       0x090
+/* @} */
+
+/** @name HDMIPHY core registers: Receiver function registers.
+  * @{
+  */
+#define XHDMIPHY1_RX_RATE_CH12_REG       0x98
+#define XHDMIPHY1_RX_RATE_CH34_REG       0x9C
+#define XHDMIPHY1_RX_CONTROL_REG         0x100
+#define XHDMIPHY1_RX_STATUS_REG          0x104
+#define XHDMIPHY1_RX_EQ_CDR_REG          0x108
+#define XHDMIPHY1_RX_TDLOCK_REG          0x10C
+/* @} */
+
+/** @name HDMIPHY core registers: Interrupt registers.
+  * @{
+  */
+#define XHDMIPHY1_INTR_EN_REG            0x110
+#define XHDMIPHY1_INTR_DIS_REG           0x114
+#define XHDMIPHY1_INTR_MASK_REG          0x118
+#define XHDMIPHY1_INTR_STS_REG           0x11C
+/* @} */
+
+/** @name User clocking registers: MMCM and BUFGGT registers.
+  * @{
+  */
+#define XHDMIPHY1_MMCM_TXUSRCLK_CTRL_REG 0x0120
+#define XHDMIPHY1_MMCM_TXUSRCLK_REG1     0x0124
+#define XHDMIPHY1_MMCM_TXUSRCLK_REG2     0x0128
+#define XHDMIPHY1_MMCM_TXUSRCLK_REG3     0x012C
+#define XHDMIPHY1_MMCM_TXUSRCLK_REG4     0x0130
+#define XHDMIPHY1_BUFGGT_TXUSRCLK_REG    0x0134
+#define XHDMIPHY1_MISC_TXUSRCLK_REG      0x0138
+
+#define XHDMIPHY1_MMCM_RXUSRCLK_CTRL_REG 0x0140
+#define XHDMIPHY1_MMCM_RXUSRCLK_REG1     0x0144
+#define XHDMIPHY1_MMCM_RXUSRCLK_REG2     0x0148
+#define XHDMIPHY1_MMCM_RXUSRCLK_REG3     0x014C
+#define XHDMIPHY1_MMCM_RXUSRCLK_REG4     0x0150
+#define XHDMIPHY1_BUFGGT_RXUSRCLK_REG    0x0154
+#define XHDMIPHY1_MISC_RXUSRCLK_REG      0x0158
+/* @} */
+
+/** @name Clock detector (HDMI) registers.
+  * @{
+  */
+#define XHDMIPHY1_CLKDET_CTRL_REG        0x0200
+#define XHDMIPHY1_CLKDET_STAT_REG        0x0204
+#define XHDMIPHY1_CLKDET_FREQ_TMR_TO_REG 0x0208
+#define XHDMIPHY1_CLKDET_FREQ_TX_REG     0x020C
+#define XHDMIPHY1_CLKDET_FREQ_RX_REG     0x0210
+#define XHDMIPHY1_CLKDET_TMR_TX_REG      0x0214
+#define XHDMIPHY1_CLKDET_TMR_RX_REG      0x0218
+#define XHDMIPHY1_CLKDET_FREQ_DRU_REG    0x021C
+/* @} */
+
+/** @name Data recovery unit registers (HDMI).
+  * @{
+  */
+#define XHDMIPHY1_DRU_CTRL_REG           0x0300
+#define XHDMIPHY1_DRU_STAT_REG           0x0304
+
+#define XHDMIPHY1_DRU_CFREQ_L_REG(Ch)    (0x0308 + (12 * (Ch - 1)))
+#define XHDMIPHY1_DRU_CFREQ_H_REG(Ch)    (0x030C + (12 * (Ch - 1)))
+#define XHDMIPHY1_DRU_GAIN_REG(Ch)       (0x0310 + (12 * (Ch - 1)))
+/* @} */
+
+/** @name TMDS Clock Pattern Generator registers (HDMI).
+  * @{
+  */
+#define XHDMIPHY1_PATGEN_CTRL_REG        0x0340
+/* @} */
+
+/******************************************************************************/
+
+/** @name HDMIPHY core masks, shifts, and register values.
+  * @{
+  */
+/* 0x0F8: VERSION */
+#define XHDMIPHY1_VERSION_INTER_REV_MASK \
+                0x000000FF  /**< Internal revision. */
+#define XHDMIPHY1_VERSION_CORE_PATCH_MASK \
+                0x00000F00  /**< Core patch details. */
+#define XHDMIPHY1_VERSION_CORE_PATCH_SHIFT 8 /**< Shift bits for core patch
+                            details. */
+#define XHDMIPHY1_VERSION_CORE_VER_REV_MASK \
+                0x0000F000  /**< Core version revision. */
+#define XHDMIPHY1_VERSION_CORE_VER_REV_SHIFT 12 /**< Shift bits for core
+                            version revision. */
+#define XHDMIPHY1_VERSION_CORE_VER_MNR_MASK \
+                0x00FF0000  /**< Core minor version. */
+#define XHDMIPHY1_VERSION_CORE_VER_MNR_SHIFT 16  /**< Shift bits for core minor
+                            version. */
+#define XHDMIPHY1_VERSION_CORE_VER_MJR_MASK \
+                0xFF000000  /**< Core major version. */
+#define XHDMIPHY1_VERSION_CORE_VER_MJR_SHIFT 24  /**< Shift bits for core major
+                            version. */
+/* 0x00C: BANK_SELECT_REG */
+#define XHDMIPHY1_BANK_SELECT_TX_MASK    0x00F
+#define XHDMIPHY1_BANK_SELECT_RX_MASK    0xF00
+#define XHDMIPHY1_BANK_SELECT_RX_SHIFT   8
+/* 0x010: REF_CLK_SEL */
+#define XHDMIPHY1_REF_CLK_SEL_QPLL0_MASK 0x0000000F
+#define XHDMIPHY1_REF_CLK_SEL_CPLL_MASK  0x000000F0
+#define XHDMIPHY1_REF_CLK_SEL_CPLL_SHIFT 4
+#define XHDMIPHY1_REF_CLK_SEL_QPLL1_MASK 0x00000F00
+#define XHDMIPHY1_REF_CLK_SEL_QPLL1_SHIFT    8
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTREFCLK0 1
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTREFCLK1 2
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTNORTHREFCLK0 3
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTNORTHREFCLK1 4
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTSOUTHREFCLK0 5
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTSOUTHREFCLK1 6
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTEASTREFCLK0 3
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTEASTREFCLK1 4
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTWESTREFCLK0 5
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTWESTREFCLK1 6
+#define XHDMIPHY1_REF_CLK_SEL_XPLL_GTGREFCLK 7
+#define XHDMIPHY1_REF_CLK_SEL_SYSCLKSEL_MASK 0x0F000000
+#define XHDMIPHY1_REF_CLK_SEL_SYSCLKSEL_SHIFT 24
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL0 0
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL1 1
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_CPLL 0
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL 1
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL0 3
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL1 2
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CH 0
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN 1
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN0 2
+#define XHDMIPHY1_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN1 3
+#define XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_OUT_MASK(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 0x03000000 : 0x02000000)
+#define XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_OUT_MASK(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 0x0C000000 : 0x08000000)
+#define XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_DATA_MASK(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 0x30000000 : 0x01000000)
+#define XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_DATA_MASK(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 0xC0000000 : 0x04000000)
+#define XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_OUT_SHIFT(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 24 : 25)
+#define XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_OUT_SHIFT(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 26 : 27)
+#define XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_DATA_SHIFT(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 28 : 24)
+#define XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_DATA_SHIFT(G) \
+    ((((G) == XHDMIPHY1_GT_TYPE_GTHE4) || \
+        ((G) == XHDMIPHY1_GT_TYPE_GTYE4)) ? 30 : 26)
+/* 0x014: PLL_RESET */
+#define XHDMIPHY1_PLL_RESET_CPLL_MASK    0x1
+#define XHDMIPHY1_PLL_RESET_QPLL0_MASK   0x2
+#define XHDMIPHY1_PLL_RESET_QPLL1_MASK   0x4
+/* 0x014: COMMON INIT for Versal Only */
+#define XHDMIPHY1_GTWIZ_RESET_ALL_MASK   0x1
+#define XHDMIPHY1_PCIERST_ALL_CH_MASK    0x2
+/* 0x018: PLL_LOCK_STATUS */
+#define XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(Ch) \
+        (0x01 << (Ch - 1))
+#define XHDMIPHY1_PLL_LOCK_STATUS_QPLL0_MASK 0x10
+#define XHDMIPHY1_PLL_LOCK_STATUS_QPLL1_MASK 0x20
+#define XHDMIPHY1_PLL_LOCK_STATUS_CPLL_ALL_MASK \
+        (XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_PLL_LOCK_STATUS_CPLL_HDMI_MASK \
+        (XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(XHDMIPHY1_CHANNEL_ID_CH3))
+#define XHDMIPHY1_PLL_LOCK_STATUS_RPLL_MASK 0xC0
+#define XHDMIPHY1_PLL_LOCK_STATUS_LCPLL_MASK 0x300
+/* 0x01C, 0x024: TX_INIT, RX_INIT */
+#define XHDMIPHY1_TXRX_INIT_GTRESET_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_PMARESET_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_PCSRESET_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_INIT_USERRDY_MASK(Ch) \
+        (0x08 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_LNKRDY_SB_MASK(Ch) \
+        (0x10 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_MSTRESET_MASK(Ch) \
+        (0x20 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_INIT_USERRDY_MASK(Ch) \
+        (0x40 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_PLLGTRESET_MASK(Ch) \
+        (0x80 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_GTRESET_ALL_MASK \
+        (XHDMIPHY1_TXRX_INIT_GTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_TXRX_INIT_GTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_TXRX_INIT_GTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_TXRX_INIT_GTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TXRX_LNKRDY_SB_ALL_MASK \
+        (XHDMIPHY1_TXRX_LNKRDY_SB_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_TXRX_LNKRDY_SB_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_TXRX_LNKRDY_SB_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_TXRX_LNKRDY_SB_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TXRX_MSTRESET_ALL_MASK \
+        (XHDMIPHY1_TXRX_MSTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_TXRX_MSTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_TXRX_MSTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_TXRX_MSTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TX_INIT_USERRDY_ALL_MASK \
+        (XHDMIPHY1_TX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_TX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_TX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_TX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_RX_INIT_USERRDY_ALL_MASK \
+        (XHDMIPHY1_RX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_RX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_RX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_RX_INIT_USERRDY_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TXRX_INIT_PLLGTRESET_ALL_MASK \
+        (XHDMIPHY1_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+         XHDMIPHY1_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+         XHDMIPHY1_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+         XHDMIPHY1_TXRX_INIT_PLLGTRESET_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+/* 0x020, 0x028: TX_STATUS, RX_STATUS */
+#define XHDMIPHY1_TXRX_INIT_STATUS_RESETDONE_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_STATUS_PMARESETDONE_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_STATUS_POWERGOOD_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TXRX_INIT_STATUS_RESETDONE_ALL_MASK \
+    (XHDMIPHY1_TXRX_INIT_STATUS_RESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+     XHDMIPHY1_TXRX_INIT_STATUS_RESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+     XHDMIPHY1_TXRX_INIT_STATUS_RESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+     XHDMIPHY1_TXRX_INIT_STATUS_RESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TXRX_INIT_STATUS_PMARESETDONE_ALL_MASK \
+    (XHDMIPHY1_TXRX_INIT_STATUS_PMARESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+     XHDMIPHY1_TXRX_INIT_STATUS_PMARESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+     XHDMIPHY1_TXRX_INIT_STATUS_PMARESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+     XHDMIPHY1_TXRX_INIT_STATUS_PMARESETDONE_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+/* 0x02C: IBUFDS_GTXX_CTRL */
+#define XHDMIPHY1_IBUFDS_GTXX_CTRL_GTREFCLK0_CEB_MASK    0x1
+#define XHDMIPHY1_IBUFDS_GTXX_CTRL_GTREFCLK1_CEB_MASK    0x2
+/* 0x030: POWERDOWN_CONTROL */
+#define XHDMIPHY1_POWERDOWN_CONTROL_CPLLPD_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_POWERDOWN_CONTROL_QPLL0PD_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_POWERDOWN_CONTROL_QPLL1PD_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_POWERDOWN_CONTROL_RXPD_MASK(Ch) \
+        (0x18 << (8 * (Ch - 1)))
+#define XHDMIPHY1_POWERDOWN_CONTROL_RXPD_SHIFT(Ch) \
+        (3 + (8 * (Ch - 1)))
+#define XHDMIPHY1_POWERDOWN_CONTROL_TXPD_MASK(Ch) \
+        (0x60 << (8 * (Ch - 1)))
+#define XHDMIPHY1_POWERDOWN_CONTROL_TXPD_SHIFT(Ch) \
+        (5 + (8 * (Ch - 1)))
+/* 0x038: LOOPBACK_CONTROL */
+#define XHDMIPHY1_LOOPBACK_CONTROL_CH_MASK(Ch) \
+        (0x03 << (8 * (Ch - 1)))
+#define XHDMIPHY1_LOOPBACK_CONTROL_CH_SHIFT(Ch) \
+        (8 * (Ch - 1))
+/* 0x040, 0x044, 0x048, 0x04C, 0x060: DRP_CONTROL_CH[1-4], DRP_CONTROL_COMMON*/
+#define XHDMIPHY1_DRP_CONTROL_DRPADDR_MASK   0x00000FFF
+#define XHDMIPHY1_DRP_CONTROL_DRPEN_MASK 0x00001000
+#define XHDMIPHY1_DRP_CONTROL_DRPWE_MASK 0x00002000
+#define XHDMIPHY1_DRP_CONTROL_DRPRESET_MASK  0x00004000
+#define XHDMIPHY1_DRP_CONTROL_DRPDI_MASK 0xFFFF0000
+#define XHDMIPHY1_DRP_CONTROL_DRPDI_SHIFT    16
+/* 0x050, 0x054, 0x058, 0x05C, 0x064: DRP_STATUS_CH[1-4], DRP_STATUS_COMMON */
+#define XHDMIPHY1_DRP_STATUS_DRPO_MASK   0x0FFFF
+#define XHDMIPHY1_DRP_STATUS_DRPRDY_MASK 0x10000
+#define XHDMIPHY1_DRP_STATUS_DRPBUSY_MASK    0x20000
+/* 0x068: CPLL CAL PERIOD */
+#define XHDMIPHY1_CPLL_CAL_PERIOD_MASK      0x3FFFF
+/* 0x06C: CPLL CAL TOLERANCE */
+#define XHDMIPHY1_CPLL_CAL_TOL_MASK         0x3FFFF
+/* 0x068: GPI */
+#define XHDMIPHY1_TX_GPI_MASK(Ch) \
+        (0x01 << (Ch - 1))
+#define XHDMIPHY1_RX_GPI_MASK(Ch) \
+        (0x10 << (Ch - 1))
+/* 0x06C: GPO */
+#define XHDMIPHY1_TX_GPO_MASK(Ch) \
+        (0x01 << (Ch - 1))
+#define XHDMIPHY1_TX_GPO_MASK_ALL(NCh) \
+		((NCh == 3) ? 0x7 : 0xF)
+#define XHDMIPHY1_TX_GPO_SHIFT 0
+#define XHDMIPHY1_RX_GPO_MASK(Ch) \
+        (0x10 << (Ch - 1))
+#define XHDMIPHY1_RX_GPO_MASK_ALL(NCh) \
+		((NCh == 3) ? 0x70 : 0xF0)
+#define XHDMIPHY1_RX_GPO_SHIFT 4
+/* 0x070: TX_CONTROL */
+#define XHDMIPHY1_TX_CONTROL_TX8B10BEN_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_CONTROL_TX8B10BEN_ALL_MASK \
+        (XHDMIPHY1_TX_CONTROL_TX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_TX_CONTROL_TX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_TX_CONTROL_TX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_TX_CONTROL_TX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TX_CONTROL_TXPOLARITY_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_CONTROL_TXPOLARITY_ALL_MASK \
+        (XHDMIPHY1_TX_CONTROL_TXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_TX_CONTROL_TXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_TX_CONTROL_TXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_TX_CONTROL_TXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TX_CONTROL_TXPRBSSEL_MASK(Ch) \
+        (0x5C << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_CONTROL_TXPRBSSEL_ALL_MASK \
+        (XHDMIPHY1_TX_CONTROL_TXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_TX_CONTROL_TXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_TX_CONTROL_TXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_TX_CONTROL_TXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_TX_CONTROL_TXPRBSSEL_SHIFT(Ch) \
+        (2 + (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_MASK(Ch) \
+        (0x20 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_ALL_MASK \
+        (XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_TX_CONTROL_TXPRBSFORCEERR_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+/* 0x074: TX_BUFFER_BYPASS */
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXPHDLYRESET_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXPHALIGN_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXPHALIGNEN_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXPHDLYPD_MASK(Ch) \
+        (0x08 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXPHINIT_MASK(Ch) \
+        (0x10 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXDLYRESET_MASK(Ch) \
+        (0x20 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXDLYBYPASS_MASK(Ch) \
+        (0x40 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_BUFFER_BYPASS_TXDLYEN_MASK(Ch) \
+        (0x80 << (8 * (Ch - 1)))
+/* 0x078: TX_STATUS */
+#define XHDMIPHY1_TX_STATUS_TXPHALIGNDONE_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_STATUS_TXPHINITDONE_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_STATUS_TXDLYRESETDONE_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_STATUS_TXBUFSTATUS_MASK(Ch) \
+        (0x18 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_STATUS_TXBUFSTATUS_SHIFT(Ch) \
+        (3 + (8 * (Ch - 1)))
+/* 0x07C, 0x080: TX_DRIVER_CH12, TX_DRIVER_CH34 */
+#define XHDMIPHY1_TX_DRIVER_TXDIFFCTRL_MASK(Ch) \
+        (0x000F << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXDIFFCTRL_SHIFT(Ch) \
+        (16 * ((Ch - 1) % 2))
+#define XHDMIPHY1_TX_DRIVER_TXELECIDLE_MASK(Ch) \
+        (0x0010 << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXELECIDLE_SHIFT(Ch) \
+        (4 + (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXINHIBIT_MASK(Ch) \
+        (0x0020 << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXINHIBIT_SHIFT(Ch) \
+        (5 + (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXPOSTCURSOR_MASK(Ch) \
+        (0x07C0 << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXPOSTCURSOR_SHIFT(Ch) \
+        (6 + (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXPRECURSOR_MASK(Ch) \
+        (0xF800 << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_DRIVER_TXPRECURSOR_SHIFT(Ch) \
+        (11 + (16 * ((Ch - 1) % 2)))
+/* 0x084: TX_DRIVER_EXT */
+#define XHDMIPHY1_TX_DRIVER_EXT_TXDIFFCTRL_MASK(Ch) \
+        (0x0001 << (8 * (Ch - 1)))
+#define XHDMIPHY1_TX_DRIVER_EXT_TXDIFFCTRL_SHIFT(Ch) \
+        (8 * (Ch - 1))
+/* 0x08C, 0x090: TX_RATE_CH12, TX_RATE_CH34 */
+#define XHDMIPHY1_TX_RATE_MASK(Ch) \
+        (0x00FF << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_TX_RATE_SHIFT(Ch) \
+        (16 * ((Ch - 1) % 2))
+/* 0x098, 0x09C: RX_RATE_CH12, RX_RATE_CH34 */
+#define XHDMIPHY1_RX_RATE_MASK(Ch) \
+        (0x00FF << (16 * ((Ch - 1) % 2)))
+#define XHDMIPHY1_RX_RATE_SHIFT(Ch) \
+        (16 * ((Ch - 1) % 2))
+/* 0x100: RX_CONTROL */
+#define XHDMIPHY1_RX_CONTROL_RX8B10BEN_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_CONTROL_RX8B10BEN_ALL_MASK \
+        (XHDMIPHY1_RX_CONTROL_RX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_RX_CONTROL_RX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_RX_CONTROL_RX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_RX_CONTROL_RX8B10BEN_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_RX_CONTROL_RXPOLARITY_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_CONTROL_RXPOLARITY_ALL_MASK \
+        (XHDMIPHY1_RX_CONTROL_RXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_RX_CONTROL_RXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_RX_CONTROL_RXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_RX_CONTROL_RXPOLARITY_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_RX_CONTROL_RXPRBSCNTRESET_MASK(Ch) \
+        (0x08 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_CONTROL_RXPRBSSEL_MASK(Ch) \
+        (0xF0 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_CONTROL_RXPRBSSEL_ALL_MASK \
+        (XHDMIPHY1_RX_CONTROL_RXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_RX_CONTROL_RXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_RX_CONTROL_RXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_RX_CONTROL_RXPRBSSEL_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+#define XHDMIPHY1_RX_CONTROL_RXPRBSSEL_SHIFT(Ch) \
+        (4 + (8 * (Ch - 1)))
+/* 0x104: RX_STATUS */
+#define XHDMIPHY1_RX_STATUS_RXCDRLOCK_MASK(Ch) \
+        (0x1 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_STATUS_RXBUFSTATUS_MASK(Ch) \
+        (0xE << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_STATUS_RXBUFSTATUS_SHIFT(Ch) \
+        (1 + (8 * (Ch - 1)))
+/* 0x104: RX_EQ_CDR */
+#define XHDMIPHY1_RX_CONTROL_RXLPMEN_MASK(Ch) \
+        (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_STATUS_RXCDRHOLD_MASK(Ch) \
+        (0x02 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_STATUS_RXOSOVRDEN_MASK(Ch) \
+        (0x04 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_STATUS_RXLPMLFKLOVRDEN_MASK(Ch) \
+        (0x08 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_STATUS_RXLPMHFOVRDEN_MASK(Ch) \
+        (0x10 << (8 * (Ch - 1)))
+#define XHDMIPHY1_RX_CONTROL_RXLPMEN_ALL_MASK \
+        (XHDMIPHY1_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY1_CHANNEL_ID_CH1) | \
+        XHDMIPHY1_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY1_CHANNEL_ID_CH2) | \
+        XHDMIPHY1_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY1_CHANNEL_ID_CH3) | \
+        XHDMIPHY1_RX_CONTROL_RXLPMEN_MASK(XHDMIPHY1_CHANNEL_ID_CH4))
+/* 0x110, 0x114, 0x118, 0x11C: INTR_EN, INTR_DIS, INTR_MASK, INTR_STS */
+#define XHDMIPHY1_INTR_TXRESETDONE_MASK      0x00000001
+#define XHDMIPHY1_INTR_RXRESETDONE_MASK      0x00000002
+#define XHDMIPHY1_INTR_CPLL_LOCK_MASK        0x00000004
+#define XHDMIPHY1_INTR_QPLL0_LOCK_MASK       0x00000008
+#define XHDMIPHY1_INTR_LCPLL_LOCK_MASK       0x00000008
+#define XHDMIPHY1_INTR_TXALIGNDONE_MASK      0x00000010
+#define XHDMIPHY1_INTR_QPLL1_LOCK_MASK       0x00000020
+#define XHDMIPHY1_INTR_RPLL_LOCK_MASK        0x00000020
+#define XHDMIPHY1_INTR_TXCLKDETFREQCHANGE_MASK   0x00000040
+#define XHDMIPHY1_INTR_RXCLKDETFREQCHANGE_MASK   0x00000080
+#define XHDMIPHY1_INTR_TXMMCMUSRCLK_LOCK_MASK    0x00000200
+#define XHDMIPHY1_INTR_RXMMCMUSRCLK_LOCK_MASK    0x00000400
+#define XHDMIPHY1_INTR_TXGPO_RE_MASK             0x00000800
+#define XHDMIPHY1_INTR_RXGPO_RE_MASK             0x00001000
+#define XHDMIPHY1_INTR_TXTMRTIMEOUT_MASK     0x40000000
+#define XHDMIPHY1_INTR_RXTMRTIMEOUT_MASK     0x80000000
+#define XHDMIPHY1_INTR_QPLL_LOCK_MASK        XHDMIPHY1_INTR_QPLL0_LOCK_MASK
+/* 0x120, 0x140: MMCM_TXUSRCLK_CTRL, MMCM_RXUSRCLK_CTRL */
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_CFG_NEW_MASK  0x01
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_RST_MASK      0x02
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_CFG_SUCCESS_MASK  0x10
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_LOCKED_MASK   0x200
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_PWRDWN_MASK   0x400
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK  0x800
+#define XHDMIPHY1_MMCM_USRCLK_CTRL_CLKINSEL_MASK 0x1000
+/* 0x124, 0x144: MMCM_TXUSRCLK_REG1, MMCM_RXUSRCLK_REG1 */
+#define XHDMIPHY1_MMCM_USRCLK_REG1_DIVCLK_MASK \
+                    0x00000FF
+#define XHDMIPHY1_MMCM_USRCLK_REG1_CLKFBOUT_MULT_MASK \
+                    0x000FF00
+#define XHDMIPHY1_MMCM_USRCLK_REG1_CLKFBOUT_MULT_SHIFT \
+                    8
+#define XHDMIPHY1_MMCM_USRCLK_REG1_CLKFBOUT_FRAC_MASK \
+                    0x3FF0000
+#define XHDMIPHY1_MMCM_USRCLK_REG1_CLKFBOUT_FRAC_SHIFT \
+                    16
+/* 0x128, 0x148: MMCM_TXUSRCLK_REG2, MMCM_RXUSRCLK_REG2 */
+#define XHDMIPHY1_MMCM_USRCLK_REG2_DIVCLK_MASK \
+                    0x00000FF
+#define XHDMIPHY1_MMCM_USRCLK_REG2_CLKOUT0_FRAC_MASK \
+                    0x3FF0000
+#define XHDMIPHY1_MMCM_USRCLK_REG2_CLKOUT0_FRAC_SHIFT \
+                    16
+/* 0x12C, 0x130, 0x14C, 0x150: MMCM_TXUSRCLK_REG[3,4], MMCM_RXUSRCLK_REG[3,4]*/
+#define XHDMIPHY1_MMCM_USRCLK_REG34_DIVCLK_MASK \
+                    0x00000FF
+/* 0x134, 0x154: BUFGT_TXUSRCLK, BUFGT_RXUSRCLK */
+#define XHDMIPHY1_BUFGGT_XXUSRCLK_CLR_MASK   0x1
+#define XHDMIPHY1_BUFGGT_XXUSRCLK_DIV_MASK   0xE
+#define XHDMIPHY1_BUFGGT_XXUSRCLK_DIV_SHIFT  1
+/* 0x138, 0x158: MISC_TXUSRCLK_REG, MISC_RXUSERCLK_REG */
+#define XHDMIPHY1_MISC_XXUSRCLK_CKOUT1_OEN_MASK  0x1
+#define XHDMIPHY1_MISC_XXUSRCLK_REFCLK_CEB_MASK  0x2
+/* 0x200: CLKDET_CTRL */
+#define XHDMIPHY1_CLKDET_CTRL_RUN_MASK           0x1
+#define XHDMIPHY1_CLKDET_CTRL_TX_TMR_CLR_MASK        0x2
+#define XHDMIPHY1_CLKDET_CTRL_RX_TMR_CLR_MASK        0x4
+#define XHDMIPHY1_CLKDET_CTRL_TX_FREQ_RST_MASK       0x8
+#define XHDMIPHY1_CLKDET_CTRL_RX_FREQ_RST_MASK       0x10
+#define XHDMIPHY1_CLKDET_CTRL_FREQ_LOCK_THRESH_MASK      0x1FE0
+#define XHDMIPHY1_CLKDET_CTRL_FREQ_LOCK_THRESH_SHIFT 5
+/* 0x204: CLKDET_STAT */
+#define XHDMIPHY1_CLKDET_STAT_TX_FREQ_ZERO_MASK      0x1
+#define XHDMIPHY1_CLKDET_STAT_RX_FREQ_ZERO_MASK      0x2
+#define XHDMIPHY1_CLKDET_STAT_TX_REFCLK_LOCK_MASK        0x3
+#define XHDMIPHY1_CLKDET_STAT_TX_REFCLK_LOCK_CAP_MASK    0x4
+/* 0x300: DRU_CTRL */
+#define XHDMIPHY1_DRU_CTRL_RST_MASK(Ch)  (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_DRU_CTRL_EN_MASK(Ch)   (0x02 << (8 * (Ch - 1)))
+/* 0x304: DRU_STAT */
+#define XHDMIPHY1_DRU_STAT_ACTIVE_MASK(Ch)   (0x01 << (8 * (Ch - 1)))
+#define XHDMIPHY1_DRU_STAT_VERSION_MASK  0xFF000000
+#define XHDMIPHY1_DRU_STAT_VERSION_SHIFT 24
+/* 0x30C, 0x318, 0x324, 0x330: DRU_CFREQ_H_CH[1-4] */
+#define XHDMIPHY1_DRU_CFREQ_H_MASK       0x1F
+/* 0x310, 0x31C, 0x328, 0x334: DRU_GAIN_CH[1-4] */
+#define XHDMIPHY1_DRU_GAIN_G1_MASK       0x00001F
+#define XHDMIPHY1_DRU_GAIN_G1_SHIFT      0
+#define XHDMIPHY1_DRU_GAIN_G1_P_MASK 0x001F00
+#define XHDMIPHY1_DRU_GAIN_G1_P_SHIFT    8
+#define XHDMIPHY1_DRU_GAIN_G2_MASK       0x1F0000
+#define XHDMIPHY1_DRU_GAIN_G2_SHIFT      16
+/* 0x340 TMDS PATGEN */
+#define XHDMIPHY1_PATGEN_CTRL_ENABLE_MASK        0x80000000
+#define XHDMIPHY1_PATGEN_CTRL_ENABLE_SHIFT       31
+#define XHDMIPHY1_PATGEN_CTRL_RATIO_MASK     0x7
+#define XHDMIPHY1_PATGEN_CTRL_RATIO_SHIFT        0
+/* @} */
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+/** @name Register access macro definitions.
+  * @{
+  */
+#define XHdmiphy1_In32 Xil_In32
+#define XHdmiphy1_Out32 Xil_Out32
+/* @} */
+
+/******************************************************************************/
+/**
+ * This is a low-level function that reads from the specified register.
+ *
+ * @param   BaseAddress is the base address of the device.
+ * @param   RegOffset is the register offset to be read from.
+ *
+ * @return  The 32-bit value of the specified register.
+ *
+ * @note    C-style signature:
+ *      u32 XHdmiphy1_ReadReg(u32 BaseAddress, u32 RegOffset)
+ *
+*******************************************************************************/
+#define XHdmiphy1_ReadReg(BaseAddress, RegOffset) \
+    XHdmiphy1_In32((BaseAddress) + (RegOffset))
+
+/******************************************************************************/
+/**
+ * This is a low-level function that writes to the specified register.
+ *
+ * @param   BaseAddress is the base address of the device.
+ * @param   RegOffset is the register offset to write to.
+ * @param   Data is the 32-bit data to write to the specified register.
+ *
+ * @return  None.
+ *
+ * @note    C-style signature:
+ *      void XHdmiphy1_WriteReg(u32 BaseAddress, u32 RegOffset, u32 Data)
+ *
+*******************************************************************************/
+#define XHdmiphy1_WriteReg(BaseAddress, RegOffset, Data) \
+    XHdmiphy1_Out32((BaseAddress) + (RegOffset), (Data))
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDMIPHY1_HW_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_i.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_i.c
@@ -0,0 +1,1881 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_i.c
+ *
+ * Contains generic APIs that are locally called or used within the
+ * HDMIPHY driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * 1.1   ku   17/05/20 Adding uniquification to avoid clash with vphy
+ * 1.1   ku   23/05/20 Corrected XHdmiphy1_Ch2Ids to set correct value
+ *                     for Id1
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include <linux/string.h>
+#include "xstatus.h"
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+#include "xhdmiphy1_hdmi.h"
+#include <linux/delay.h>
+#include "xhdmiphy1_gt.h"
+
+/**************************** Function Prototypes *****************************/
+
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function will set the channel IDs to correspond with the supplied
+* channel ID based on the protocol. HDMI uses 3 channels; This ID
+* translation is done to allow other functions to operate iteratively over
+* multiple channels.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	ChId is the channel ID used to determine the indices.
+* @param	Id0 is a pointer to the start channel ID to set.
+* @param	Id1 is a pointer to the end channel ID to set.
+*
+* @return	None.
+*
+* @note		The contents of Id0 and Id1 will be set according to ChId.
+*
+******************************************************************************/
+void XHdmiphy1_Ch2Ids(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+		u8 *Id0, u8 *Id1)
+{
+	u8 Channels = 4;
+
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		*Id0 = XHDMIPHY1_CHANNEL_ID_CH1;
+		if ((XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) ||
+			(XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX))) {
+			if ((InstancePtr->Config.TxProtocol == XHDMIPHY1_PROTOCOL_HDMI21) ||
+					(InstancePtr->Config.RxProtocol == XHDMIPHY1_PROTOCOL_HDMI21)) {
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH4;
+			}
+			else if ((InstancePtr->Config.TxProtocol == XHDMIPHY1_PROTOCOL_HDMI) &&
+					(InstancePtr->Config.UseGtAsTxTmdsClk == TRUE)){
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH4;
+			}
+			else {
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH3;
+			}
+		}
+		else {
+			Channels = ((InstancePtr->Config.TxChannels >=
+				InstancePtr->Config.RxChannels) ?
+				InstancePtr->Config.TxChannels :
+				InstancePtr->Config.RxChannels);
+
+			if (Channels == 1) {
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH1;
+			}
+			else if (Channels == 2) {
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH2;
+			}
+			else if (Channels == 3) {
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH3;
+			}
+			else {
+				*Id1 = XHDMIPHY1_CHANNEL_ID_CH4;
+			}
+		}
+	}
+	else if (ChId == XHDMIPHY1_CHANNEL_ID_CMNA) {
+		*Id0 = XHDMIPHY1_CHANNEL_ID_CMN0;
+		if ((InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTHE4) ||
+		    (InstancePtr->Config.XcvrType == XHDMIPHY1_GT_TYPE_GTYE4)) {
+			*Id1 = XHDMIPHY1_CHANNEL_ID_CMN1;
+		}
+		else {
+			*Id1 = XHDMIPHY1_CHANNEL_ID_CMN0;
+		}
+	}
+	else {
+		*Id0 = *Id1 = ChId;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will set the current RX/TX configuration over DRP.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID for which to write the settings for.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_DirReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 Status = XST_SUCCESS;
+	u8 Id, Id0, Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (Dir == XHDMIPHY1_DIR_TX) {
+			Status |= XHdmiphy1_TxChReconfig(InstancePtr, QuadId,
+						(XHdmiphy1_ChannelId)Id);
+		}
+		else {
+			Status |= XHdmiphy1_RxChReconfig(InstancePtr, QuadId,
+						(XHdmiphy1_ChannelId)Id);
+		}
+		if (Status != XST_SUCCESS) {
+			Status = XST_FAILURE;
+			break;
+		}
+	}
+
+	XHdmiphy1_LogWrite(InstancePtr, (Dir == XHDMIPHY1_DIR_TX) ?
+	XHDMIPHY1_LOG_EVT_GT_TX_RECONFIG : XHDMIPHY1_LOG_EVT_GT_RX_RECONFIG, 1);
+
+	return Status;
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* This function writes the current software configuration for the reference
+* clock selections to hardware for the specified quad on all channels.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_WriteCfgRefClkSelReg(XHdmiphy1 *InstancePtr, u8 QuadId)
+{
+	u32 RegVal = 0;
+	XHdmiphy1_Channel *ChPtr;
+	XHdmiphy1_GtType GtType = InstancePtr->Config.XcvrType;
+
+	/* Point to the first channel since settings apply to all channels. */
+	ChPtr = &InstancePtr->Quads[QuadId].Ch1;
+
+	/* PllRefClkSel. */
+	/* - QPLL0. */
+	RegVal &= ~XHDMIPHY1_REF_CLK_SEL_QPLL0_MASK;
+	RegVal = InstancePtr->Quads[QuadId].Cmn0.PllRefClkSel;
+	/* - CPLL. */
+	RegVal &= ~XHDMIPHY1_REF_CLK_SEL_CPLL_MASK;
+	RegVal |= (ChPtr->CpllRefClkSel << XHDMIPHY1_REF_CLK_SEL_CPLL_SHIFT);
+	if ((GtType == XHDMIPHY1_GT_TYPE_GTHE4) ||
+            (GtType == XHDMIPHY1_GT_TYPE_GTYE4)) {
+		/* - QPLL1. */
+		RegVal &= ~XHDMIPHY1_REF_CLK_SEL_QPLL1_MASK;
+		RegVal |= (InstancePtr->Quads[QuadId].Cmn1.PllRefClkSel <<
+				XHDMIPHY1_REF_CLK_SEL_QPLL1_SHIFT);
+	}
+
+	/* SysClkDataSel. PLLCLKSEL */
+	RegVal &= ~XHDMIPHY1_REF_CLK_SEL_SYSCLKSEL_MASK;
+	/* - TXSYSCLKSEL[0]. TXPLLCLKSEL*/
+	RegVal |= (ChPtr->TxDataRefClkSel <<
+		XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_DATA_SHIFT(GtType)) &
+		XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_DATA_MASK(GtType);
+	/* - RXSYSCLKSEL[0]. RXPLLCLKSEL*/
+	RegVal |= (ChPtr->RxDataRefClkSel <<
+		XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_DATA_SHIFT(GtType)) &
+		XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_DATA_MASK(GtType);
+
+	/* SysClkOutSel. */
+	/* - TXSYSCLKSEL[1]. */
+	RegVal |= (ChPtr->TxOutRefClkSel <<
+		XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_OUT_SHIFT(GtType)) &
+		XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_OUT_MASK(GtType);
+	/* - RXSYSCLKSEL[1]. */
+	RegVal |= (ChPtr->RxOutRefClkSel <<
+		XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_OUT_SHIFT(GtType)) &
+		XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_OUT_MASK(GtType);
+
+	/* Write to hardware. */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+			 XHDMIPHY1_REF_CLK_SEL_REG,RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* Configure the PLL reference clock selection for the specified channel(s).
+* This is applied to both direction to the software configuration only.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	SysClkDataSel is the reference clock selection to configure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_CfgPllRefClkSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_PllRefClkSelType RefClkSel)
+{
+	u8 Id, Id0, Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].PllRefClkSel =
+					RefClkSel;
+	}
+}
+
+/*****************************************************************************/
+/**
+* Configure the SYSCLKDATA reference clock selection for the direction. Same
+* configuration applies to all channels in the quad. This is applied to the
+* software configuration only.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	SysClkDataSel is the reference clock selection to configure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_CfgSysClkDataSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir,
+		XHdmiphy1_SysClkDataSelType SysClkDataSel)
+{
+	XHdmiphy1_Channel *ChPtr;
+	u8 Id, Id0, Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	/* Select in software - same for all channels. */
+	for (Id = Id0; Id <= Id1; Id++) {
+		ChPtr = &InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)];
+		ChPtr->DataRefClkSel[Dir] = SysClkDataSel;
+	}
+}
+
+/*****************************************************************************/
+/**
+* Configure the SYSCLKOUT reference clock selection for the direction. Same
+* configuration applies to all channels in the quad. This is applied to the
+* software configuration only.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	SysClkOutSel is the reference clock selection to configure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_CfgSysClkOutSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir,
+		XHdmiphy1_SysClkOutSelType SysClkOutSel)
+{
+	XHdmiphy1_Channel *ChPtr;
+	u8 Id, Id0, Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	/* Select in software - same for all channels. */
+	for (Id = Id0; Id <= Id1; Id++) {
+		ChPtr = &InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)];
+		ChPtr->OutRefClkSel[Dir] = SysClkOutSel;
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+* Obtain the reconfiguration channel ID for given PLL type
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	PllType is the PLL type being used by the channel.
+*
+* @return	The Channel ID to be used for reconfiguration
+*
+* @note		None.
+*
+******************************************************************************/
+XHdmiphy1_ChannelId XHdmiphy1_GetRcfgChId(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, XHdmiphy1_PllType PllType)
+{
+	XHdmiphy1_ChannelId ChId;
+
+	/* Suppress Warning Messages */
+	InstancePtr = InstancePtr;
+	QuadId = QuadId;
+	Dir = Dir;
+
+	/* Determine which channel(s) to operate on. */
+	switch (PllType) {
+	case XHDMIPHY1_PLL_TYPE_QPLL:
+	case XHDMIPHY1_PLL_TYPE_QPLL0:
+	case XHDMIPHY1_PLL_TYPE_LCPLL:
+		ChId = XHDMIPHY1_CHANNEL_ID_CMN0;
+		break;
+	case XHDMIPHY1_PLL_TYPE_QPLL1:
+	case XHDMIPHY1_PLL_TYPE_RPLL:
+		ChId = XHDMIPHY1_CHANNEL_ID_CMN1;
+		break;
+	default:
+		ChId = XHDMIPHY1_CHANNEL_ID_CHA;
+		break;
+	}
+
+	return ChId;
+}
+
+/*****************************************************************************/
+/**
+* This function will check the status of a PLL lock on the specified channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return
+*		- XST_SUCCESS if the specified PLL is locked.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_IsPllLocked(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	u32 RegVal;
+	u32 MaskVal;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	XHdmiphy1_PllType TxPllType;
+	XHdmiphy1_PllType RxPllType;
+#endif
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (ChId == XHDMIPHY1_CHANNEL_ID_CMN0) {
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_QPLL0_MASK;
+#else
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_LCPLL_MASK;
+#endif
+	}
+	else if (ChId == XHDMIPHY1_CHANNEL_ID_CMN1) {
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_QPLL1_MASK;
+#else
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_RPLL_MASK;
+	}
+	else {
+		/* This will result to XST_FAILURE */
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_CPLL_ALL_MASK;
+#endif
+	}
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	else if (ChId == XHDMIPHY1_CHANNEL_ID_CMNA) {
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_QPLL0_MASK |
+			  XHDMIPHY1_PLL_LOCK_STATUS_QPLL1_MASK;
+	}
+	else if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+		TxPllType = XHdmiphy1_GetPllType(InstancePtr, 0,
+				XHDMIPHY1_DIR_TX, XHDMIPHY1_CHANNEL_ID_CH1);
+		RxPllType = XHdmiphy1_GetPllType(InstancePtr, 0,
+				XHDMIPHY1_DIR_RX, XHDMIPHY1_CHANNEL_ID_CH1);
+		if (RxPllType == XHDMIPHY1_PLL_TYPE_CPLL &&
+			XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+			MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_CPLL_HDMI_MASK;
+		}
+		else if (TxPllType == XHDMIPHY1_PLL_TYPE_CPLL &&
+			XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+			MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_CPLL_HDMI_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_CPLL_ALL_MASK;
+		}
+	}
+	else {
+		MaskVal = XHDMIPHY1_PLL_LOCK_STATUS_CPLL_MASK(ChId);
+	}
+#endif
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_PLL_LOCK_STATUS_REG);
+
+	if ((RegVal & MaskVal) == MaskVal) {
+		return XST_SUCCESS;
+	}
+
+	return XST_FAILURE;
+}
+
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* Obtain the current reference clock frequency for the quad based on the
+* reference clock type.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	RefClkType is the type to obtain the clock selection for.
+*
+* @return	The current reference clock frequency for the quad for the
+*		specified type selection.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_GetQuadRefClkFreq(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_PllRefClkSelType RefClkType)
+{
+	u32 FreqHz;
+
+	u8 RefClkIndex = RefClkType - XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTREFCLK0;
+
+	FreqHz = (RefClkType > XHDMIPHY1_PLL_REFCLKSEL_TYPE_GTGREFCLK) ? 0 :
+		InstancePtr->Quads[QuadId].RefClkHz[RefClkIndex];
+
+	return FreqHz;
+}
+
+/*****************************************************************************/
+/**
+* Obtain the current [RT]XSYSCLKSEL[0] configuration.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return	The current [RT]XSYSCLKSEL[0] selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdmiphy1_SysClkDataSelType XHdmiphy1_GetSysClkDataSel(XHdmiphy1 *InstancePtr,
+        u8 QuadId, XHdmiphy1_DirectionType Dir, XHdmiphy1_ChannelId ChId)
+{
+	u32 Sel;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	ChId = ChId;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+						XHDMIPHY1_REF_CLK_SEL_REG);
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_DATA_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_DATA_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+	else {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_DATA_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_DATA_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+
+	return (XHdmiphy1_SysClkDataSelType) Sel;
+}
+
+/*****************************************************************************/
+/**
+* Obtain the current [RT]XSYSCLKSEL[1] configuration.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return	The current [RT]XSYSCLKSEL[1] selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdmiphy1_SysClkOutSelType XHdmiphy1_GetSysClkOutSel(XHdmiphy1 *InstancePtr,
+        u8 QuadId, XHdmiphy1_DirectionType Dir, XHdmiphy1_ChannelId ChId)
+{
+	u32 Sel;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	ChId = ChId;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_REF_CLK_SEL_REG);
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_OUT_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XHDMIPHY1_REF_CLK_SEL_TXSYSCLKSEL_OUT_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+	else {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_OUT_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XHDMIPHY1_REF_CLK_SEL_RXSYSCLKSEL_OUT_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+
+	return (XHdmiphy1_SysClkOutSelType)Sel;
+}
+
+/*****************************************************************************/
+/**
+* This function will reset and enable the Video PHY's user core logic.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_GtUserRdyEnable(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Hold)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_TX_INIT_REG;
+
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+			MaskVal = XHDMIPHY1_TX_INIT_USERRDY_ALL_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_TX_INIT_USERRDY_MASK(ChId);
+		}
+	}
+	else {
+		RegOffset = XHDMIPHY1_RX_INIT_REG;
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CHA) {
+			MaskVal = XHDMIPHY1_RX_INIT_USERRDY_ALL_MASK;
+		}
+		else {
+			MaskVal = XHDMIPHY1_RX_INIT_USERRDY_MASK(ChId);
+		}
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	/* Assert reset. */
+	RegVal |= MaskVal;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~MaskVal;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+					RegOffset, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+#else
+/*****************************************************************************/
+/**
+* This function will set the TXRATE or RXRATE port to select the GT Wizard
+* configuration
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_SetGtLineRateCfg(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 ShiftVal;
+	u32 RegOffset;
+	u16 LRCfgVal;
+	XHdmiphy1_PllType PllType;
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, Dir,
+    			XHDMIPHY1_CHANNEL_ID_CH1);
+
+    /* Extract Line Rate Config Value */
+    if (PllType == XHDMIPHY1_PLL_TYPE_LCPLL) {
+    	LRCfgVal = InstancePtr->Quads[QuadId].Lcpll.LineRateCfg;
+    }
+    else { /* RPLL */
+    	LRCfgVal = InstancePtr->Quads[QuadId].Rpll.LineRateCfg;
+    }
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+			(ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+			RegOffset = XHDMIPHY1_TX_RATE_CH12_REG;
+		}
+		else {
+			RegOffset = XHDMIPHY1_TX_RATE_CH34_REG;
+		}
+		MaskVal = XHDMIPHY1_TX_RATE_MASK(ChId);
+		ShiftVal = XHDMIPHY1_TX_RATE_SHIFT(ChId);
+	}
+	else{
+		if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+			(ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+			RegOffset = XHDMIPHY1_RX_RATE_CH12_REG;
+		}
+		else {
+			RegOffset = XHDMIPHY1_RX_RATE_CH34_REG;
+		}
+		MaskVal = XHDMIPHY1_RX_RATE_MASK(ChId);
+		ShiftVal = XHDMIPHY1_RX_RATE_SHIFT(ChId);
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	RegVal &= ~MaskVal;
+	RegVal |= (LRCfgVal << ShiftVal);
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will get the TXRATE or RXRATE port to select the GT Wizard
+* configuration
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XHdmiphy1_GetGtLineRateCfg(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 ShiftVal;
+	u32 RegOffset;
+	u16 LRCfgVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+			(ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+			RegOffset = XHDMIPHY1_TX_RATE_CH12_REG;
+		}
+		else {
+			RegOffset = XHDMIPHY1_TX_RATE_CH34_REG;
+		}
+		MaskVal = XHDMIPHY1_TX_RATE_MASK(ChId);
+		ShiftVal = XHDMIPHY1_TX_RATE_SHIFT(ChId);
+	}
+	else{
+		if ((ChId == XHDMIPHY1_CHANNEL_ID_CH1) ||
+			(ChId == XHDMIPHY1_CHANNEL_ID_CH2)) {
+			RegOffset = XHDMIPHY1_RX_RATE_CH12_REG;
+		}
+		else {
+			RegOffset = XHDMIPHY1_RX_RATE_CH34_REG;
+		}
+		MaskVal = XHDMIPHY1_RX_RATE_MASK(ChId);
+		ShiftVal = XHDMIPHY1_RX_RATE_SHIFT(ChId);
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	RegVal &= MaskVal;
+	LRCfgVal = (u16)(RegVal >> ShiftVal);
+
+	return LRCfgVal;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the GPI ports to the GT Wizard
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Set Set=TRUE; Clear=FALSE
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_SetGpi(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Set)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+    /* Read GPI Register*/
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_GT_DBG_GPI_REG);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (Dir == XHDMIPHY1_DIR_TX) {
+			MaskVal |=  XHDMIPHY1_TX_GPI_MASK(Id);
+		}
+		else {
+			MaskVal |=  XHDMIPHY1_RX_GPI_MASK(Id);
+		}
+	}
+
+	/* Construct Register Value */
+	if (Set) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+
+	/* Write GPI Register*/
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_GT_DBG_GPI_REG, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will get the GPI ports value from the GT Wizard
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	Value.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XHdmiphy1_GetGpo(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	ChId = ChId;
+
+    /* Read GPI Register*/
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_GT_DBG_GPO_REG);
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		return ((RegVal &
+					XHDMIPHY1_TX_GPO_MASK_ALL(InstancePtr->Config.TxChannels))
+						>> XHDMIPHY1_TX_GPO_SHIFT);
+	}
+	else {
+		return ((RegVal &
+					XHDMIPHY1_RX_GPO_MASK_ALL(InstancePtr->Config.RxChannels))
+						>> XHDMIPHY1_RX_GPO_SHIFT);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will set the (TX|RX) MSTRESET port of the GT
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Reset Set=TRUE; Clear=FALSE
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_GtMstReset(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Reset)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |=  XHDMIPHY1_TXRX_MSTRESET_MASK(Id);
+	}
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffsetCtrl = XHDMIPHY1_TX_INIT_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_RX_INIT_REG;
+	}
+
+	/* Read TX|RX INIT Register*/
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+				RegOffsetCtrl);
+
+	/* Construct Register Value */
+	if (Reset) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+
+	/* Write TX|RX INIT Register*/
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+			RegOffsetCtrl, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will will check the current CFG setting and compare
+* it with the next CFG value
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Reset Set=TRUE; Clear=FALSE
+*
+* @return	TRUE if Current and Next CFG are the same
+*           FALSE if Current and Next CFG are different
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XHdmiphy1_CheckLineRateCfg(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u16 CurrCfgVal, LRCfgVal;
+	XHdmiphy1_PllType PllType;
+
+    /* Determine PLL type. */
+    PllType = XHdmiphy1_GetPllType(InstancePtr, 0, Dir,
+			XHDMIPHY1_CHANNEL_ID_CH1);
+
+    /* Extract Line Rate Config Value */
+    if (PllType == XHDMIPHY1_PLL_TYPE_LCPLL) {
+	LRCfgVal = InstancePtr->Quads[QuadId].Lcpll.LineRateCfg;
+    }
+    else { /* RPLL */
+	LRCfgVal = InstancePtr->Quads[QuadId].Rpll.LineRateCfg;
+    }
+
+    /* Get current line rate configuration value */
+	CurrCfgVal = XHdmiphy1_GetGtLineRateCfg(InstancePtr, QuadId, ChId, Dir);
+
+	if (CurrCfgVal != LRCfgVal) {
+		return FALSE;
+	}
+	else {
+		return TRUE;
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will reset the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_MmcmReset(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u8 Hold)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	/* Assert reset. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+	RegVal |= XHDMIPHY1_MMCM_USRCLK_CTRL_RST_MASK;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~XHDMIPHY1_MMCM_USRCLK_CTRL_RST_MASK;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl,
+									RegVal);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will reset the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable is an indicator whether to "Enable" the locked mask
+*		if set to 1. If set to 0: reset, then disable.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_MmcmLockedMaskEnable(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, u8 Enable)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	/* Assert reset. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+	RegVal |= XHDMIPHY1_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	if (!Enable) {
+		/* De-assert reset. */
+		RegVal &= ~XHDMIPHY1_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl,
+									RegVal);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will get the lock status of the mixed-mode clock
+* manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+
+*
+* @return	TRUE if Locked else FALSE.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XHdmiphy1_MmcmLocked(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			RegOffsetCtrl) & XHDMIPHY1_MMCM_USRCLK_CTRL_LOCKED_MASK;
+
+	return (RegVal ? TRUE : FALSE);
+
+}
+
+/*****************************************************************************/
+/**
+* This function will set the CLKINSEL port of the MMCM
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Sel CLKINSEL value
+* 				0 - CLKIN1
+* 				1 - CLKIN2
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_MmcmSetClkinsel(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, XHdmiphy1_MmcmClkinsel Sel)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XHDMIPHY1_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+
+	if (Sel == XHDMIPHY1_MMCM_CLKINSEL_CLKIN2) {
+		RegVal &= ~XHDMIPHY1_MMCM_USRCLK_CTRL_CLKINSEL_MASK;
+	}
+	else {
+		RegVal |= XHDMIPHY1_MMCM_USRCLK_CTRL_CLKINSEL_MASK;
+	}
+
+	 XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+				RegOffsetCtrl, RegVal);
+
+}
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+/*****************************************************************************/
+/**
+* This function obtains the divider value of the BUFG_GT peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Dir is an indicator for TX or RX
+* @param	Div 3-bit divider value
+*
+* @return	None.
+*
+******************************************************************************/
+void XHdmiphy1_SetBufgGtDiv(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir, u8 Div)
+{
+	u32 RegVal;
+	u32 RegOffset;
+	u8 Divider = Div;
+
+	if (Divider == 0) {
+		Divider = 1;
+	}
+	else {
+		Divider = Divider - 1;
+	}
+
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		RegOffset = XHDMIPHY1_BUFGGT_TXUSRCLK_REG;
+	}
+	else {
+		RegOffset = XHDMIPHY1_BUFGGT_RXUSRCLK_REG;
+	}
+
+	/* Read BUFG_GT register. */
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	RegVal &= ~XHDMIPHY1_BUFGGT_XXUSRCLK_DIV_MASK;
+
+	/* Shift divider value to correct position. */
+	Divider <<= XHDMIPHY1_BUFGGT_XXUSRCLK_DIV_SHIFT;
+	Divider &= XHDMIPHY1_BUFGGT_XXUSRCLK_DIV_MASK;
+	RegVal |= Divider;
+
+	/* Write new value to BUFG_GT ctrl register. */
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will power down the specified GT PLL.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to power down the PLL for.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the power down if set
+*		to 1. If set to 0: power down, then power back up.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_PowerDownGtPll(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Hold)
+{
+	u32 MaskVal = 0;
+	u32 RegVal;
+	u8 Id, Id0, Id1;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (XHDMIPHY1_ISCH(ChId)) {
+		XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	}
+	else {
+		/* When powering down a QPLL, power down for all channels. */
+		XHdmiphy1_Ch2Ids(InstancePtr,
+				XHDMIPHY1_CHANNEL_ID_CHA, &Id0, &Id1);
+	}
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (ChId == XHDMIPHY1_CHANNEL_ID_CMN0) {
+			MaskVal |= XHDMIPHY1_POWERDOWN_CONTROL_QPLL0PD_MASK(Id);
+		}
+		else if (ChId == XHDMIPHY1_CHANNEL_ID_CMN1) {
+			MaskVal |= XHDMIPHY1_POWERDOWN_CONTROL_QPLL1PD_MASK(Id);
+		}
+		else if (ChId == XHDMIPHY1_CHANNEL_ID_CMNA) {
+			MaskVal |= XHDMIPHY1_POWERDOWN_CONTROL_QPLL0PD_MASK(Id) |
+				   XHDMIPHY1_POWERDOWN_CONTROL_QPLL1PD_MASK(Id);
+		}
+		else {
+			MaskVal |= XHDMIPHY1_POWERDOWN_CONTROL_CPLLPD_MASK(Id);
+		}
+	}
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+					XHDMIPHY1_POWERDOWN_CONTROL_REG);
+	RegVal |= MaskVal;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_POWERDOWN_CONTROL_REG, RegVal);
+
+	if (!Hold) {
+		RegVal &= ~MaskVal;
+		XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr,
+				XHDMIPHY1_POWERDOWN_CONTROL_REG, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will try to find the necessary PLL divisor values to produce
+* the configured line rate given the specified PLL input frequency. This will
+* be done for all channels specified by ChId.
+* This function is a wrapper for XHdmiphy1_PllCalculator.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to calculate the PLL values for.
+* @param	ChId is the channel ID to calculate the PLL values for.
+* @param	Dir is an indicator for TX or RX.
+* @param	PllClkInFreqHz is the PLL input frequency on which to base the
+*		calculations on. A value of 0 indicates to use the currently
+*		configured quad PLL reference clock. A non-zero value indicates
+*		to ignore what is currently configured in SW, and use a custom
+*		frequency instead.
+*
+* @return
+*		- XST_SUCCESS if valid PLL values were found to satisfy the
+*		  constraints.
+*		- XST_FAILURE otherwise.
+*
+* @note		If successful, the channel's PllParams structure will be
+*		modified with the valid PLL parameters.
+*
+******************************************************************************/
+u32 XHdmiphy1_ClkCalcParams(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        u32 PllClkInFreqHz)
+{
+	u32 Status = XST_SUCCESS;
+	u8 Id, Id0, Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		Status = XHdmiphy1_PllCalculator(InstancePtr, QuadId,
+				(XHdmiphy1_ChannelId)Id, Dir, PllClkInFreqHz);
+		if (Status != XST_SUCCESS) {
+			return Status;
+		}
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the current output divider configuration over DRP.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID for which to write the settings for.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_OutDivReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u32 Status;
+	u8 Id;
+	u8 Id0;
+	u8 Id1;
+
+	if (!XHDMIPHY1_ISCH(ChId)) {
+		ChId = XHDMIPHY1_CHANNEL_ID_CHA;
+	}
+
+	XHdmiphy1_LogWrite(InstancePtr, (Dir == XHDMIPHY1_DIR_TX) ?
+	XHDMIPHY1_LOG_EVT_GT_TX_RECONFIG : XHDMIPHY1_LOG_EVT_GT_RX_RECONFIG, 0);
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		Status = XHdmiphy1_OutDivChReconfig(InstancePtr, QuadId,
+					(XHdmiphy1_ChannelId)Id, Dir);
+		if (Status != XST_SUCCESS) {
+			break;
+		}
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the current clocking settings for each channel to
+* hardware based on the configuration stored in the driver's instance.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID for which to write the settings for.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_ClkReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	u32 Status = XST_SUCCESS;
+	u8 Id;
+	u8 Id0;
+	u8 Id1;
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (XHDMIPHY1_ISCH(Id)) {
+			Status |= XHdmiphy1_ClkChReconfig(InstancePtr, QuadId,
+						(XHdmiphy1_ChannelId)Id);
+		}
+		else if (XHDMIPHY1_ISCMN(ChId)) {
+			if (((XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) ||
+				(XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX))) &&
+			    (InstancePtr->HdmiIsQpllPresent == FALSE)) {
+				XHdmiphy1_LogWrite(InstancePtr, XHDMIPHY1_LOG_EVT_NO_QPLL_ERR,
+                    1);
+				XHdmiphy1_ErrorHandler(InstancePtr);
+				Status = XST_FAILURE;
+				return Status;
+			}
+			Status |= XHdmiphy1_ClkCmnReconfig(InstancePtr, QuadId,
+						(XHdmiphy1_ChannelId)Id);
+		}
+		if (Status != XST_SUCCESS) {
+			Status = XST_FAILURE;
+			return Status;
+		}
+	}
+
+	if (XHDMIPHY1_ISCH(ChId)) {
+		XHdmiphy1_LogWrite(InstancePtr,
+			XHDMIPHY1_LOG_EVT_CPLL_RECONFIG, 1);
+	}
+	else if (XHDMIPHY1_ISCMN(ChId)) {
+		XHdmiphy1_LogWrite(InstancePtr,
+			XHDMIPHY1_LOG_EVT_QPLL_RECONFIG, 1);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate from XHdmiphy1_PllType to
+* XHdmiphy1_SysClkDataSelType.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	The reference clock type based on the PLL selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdmiphy1_SysClkDataSelType XHdmiphy1_Pll2SysClkData(XHdmiphy1_PllType PllSelect)
+{
+	return	(PllSelect == XHDMIPHY1_PLL_TYPE_CPLL) ?
+			XHDMIPHY1_SYSCLKSELDATA_TYPE_CPLL_OUTCLK :
+		(PllSelect == XHDMIPHY1_PLL_TYPE_QPLL) ?
+			XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL_OUTCLK :
+		(PllSelect == XHDMIPHY1_PLL_TYPE_QPLL0) ?
+			XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK :
+		/*(PllSelect == XHDMIPHY1_PLL_TYPE_QPLL1) ?*/
+			XHDMIPHY1_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate from XHdmiphy1_PllType to
+* XHdmiphy1_SysClkOutSelType.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	The reference clock type based on the PLL selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XHdmiphy1_SysClkOutSelType XHdmiphy1_Pll2SysClkOut(XHdmiphy1_PllType PllSelect)
+{
+	return	(PllSelect == XHDMIPHY1_PLL_TYPE_CPLL) ?
+			XHDMIPHY1_SYSCLKSELOUT_TYPE_CPLL_REFCLK :
+		(PllSelect == XHDMIPHY1_PLL_TYPE_QPLL) ?
+			XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL_REFCLK :
+		(PllSelect == XHDMIPHY1_PLL_TYPE_QPLL0) ?
+			XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL0_REFCLK :
+		/*(PllSelect == XHDMIPHY1_PLL_TYPE_QPLL1) ?*/
+			XHDMIPHY1_SYSCLKSELOUT_TYPE_QPLL1_REFCLK;
+}
+
+/*****************************************************************************/
+/**
+* This function will try to find the necessary PLL divisor values to produce
+* the configured line rate given the specified PLL input frequency.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to calculate the PLL values for.
+* @param	ChId is the channel ID to calculate the PLL values for.
+* @param	Dir is an indicator for TX or RX.
+* @param	PllClkInFreqHz is the PLL input frequency on which to base the
+*		calculations on. A value of 0 indicates to use the currently
+*		configured quad PLL reference clock. A non-zero value indicates
+*		to ignore what is currently configured in SW, and use a custom
+*		frequency instead.
+*
+* @return
+*		- XST_SUCCESS if valid PLL values were found to satisfy the
+*		  constraints.
+*		- XST_FAILURE otherwise.
+*
+* @note		If successful, the channel's PllParams structure will be
+*		modified with the valid PLL parameters.
+*
+******************************************************************************/
+u32 XHdmiphy1_PllCalculator(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+		u32 PllClkInFreqHz)
+{
+	u32 Status;
+	u64 PllClkOutFreqHz;
+	u64 CalcLineRateFreqHz;
+	u8 Id, Id0, Id1;
+	u64 PllClkInFreqHzIn = PllClkInFreqHz;
+	XHdmiphy1_Channel *PllPtr = &InstancePtr->Quads[QuadId].
+		Plls[XHDMIPHY1_CH2IDX(ChId)];
+
+	if (!PllClkInFreqHzIn) {
+		PllClkInFreqHzIn = XHdmiphy1_GetQuadRefClkFreq(InstancePtr,
+					QuadId,
+					PllPtr->PllRefClkSel);
+	}
+
+	/* Select PLL value table offsets. */
+	const XHdmiphy1_GtPllDivs *GtPllDivs;
+	if (XHDMIPHY1_ISCH(ChId)) {
+		GtPllDivs = &InstancePtr->GtAdaptor->CpllDivs;
+	}
+	else {
+		GtPllDivs = &InstancePtr->GtAdaptor->QpllDivs;
+	}
+
+	const u8 *M, *N1, *N2, *D;
+	for (N2 = GtPllDivs->N2; *N2 != 0; N2++) {
+	for (N1 = GtPllDivs->N1; *N1 != 0; N1++) {
+	for (M = GtPllDivs->M;   *M != 0;  M++) {
+		PllClkOutFreqHz = (PllClkInFreqHzIn * *N1 * *N2) / *M;
+
+		/* Test if the calculated PLL clock is in the VCO range. */
+		Status = XHdmiphy1_CheckPllOpRange(InstancePtr, QuadId, ChId,
+				PllClkOutFreqHz);
+		if (Status != XST_SUCCESS) {
+			continue;
+		}
+
+		if ((XHDMIPHY1_ISCH(ChId))) {
+			PllClkOutFreqHz *= 2;
+		}
+
+		/* Apply TX/RX divisor. */
+		for (D = GtPllDivs->D; *D != 0; D++) {
+			CalcLineRateFreqHz = PllClkOutFreqHz / *D;
+			if (CalcLineRateFreqHz == PllPtr->LineRateHz) {
+				goto calc_done;
+			}
+		}
+	}
+	}
+	}
+	/* Calculation failed, don't change divisor settings. */
+	return XST_FAILURE;
+
+calc_done:
+	/* Found the multiplier and divisor values for requested line rate. */
+	PllPtr->PllParams.MRefClkDiv = *M;
+	PllPtr->PllParams.NFbDiv = *N1;
+	PllPtr->PllParams.N2FbDiv = *N2; /* Won't be used for QPLL.*/
+	PllPtr->PllParams.IsLowerBand = 1; /* Won't be used for CPLL. */
+
+	if (XHDMIPHY1_ISCMN(ChId)) {
+		/* Same divisor value for all channels if using a QPLL. */
+		ChId = XHDMIPHY1_CHANNEL_ID_CHA;
+	}
+
+	XHdmiphy1_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(Id)].OutDiv[Dir] =
+			*D;
+		if (Dir == XHDMIPHY1_DIR_RX) {
+			XHdmiphy1_CfgSetCdr(InstancePtr,\
+				QuadId, (XHdmiphy1_ChannelId)Id);
+		}
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the PLL VCO operating frequency.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	PLL VCO frequency in Hz
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XHdmiphy1_GetPllVcoFreqHz(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	u64 PllxVcoRateHz;
+	u64 PllRefClkHz;
+	XHdmiphy1_Channel *PllPtr = &InstancePtr->Quads[QuadId].
+                    Plls[XHDMIPHY1_CH2IDX(ChId)];
+
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_TX)) {
+			PllRefClkHz = InstancePtr->HdmiTxRefClkHz;
+		}
+		else {
+			PllRefClkHz = XHdmiphy1_GetQuadRefClkFreq(InstancePtr,
+							QuadId,
+							PllPtr->PllRefClkSel);
+		}
+	}
+	else {
+		if (XHdmiphy1_IsHDMI(InstancePtr, XHDMIPHY1_DIR_RX)) {
+			if (InstancePtr->HdmiRxDruIsEnabled) {
+				PllRefClkHz =
+				XHdmiphy1_DruGetRefClkFreqHz(InstancePtr);
+			}
+			else {
+				PllRefClkHz = InstancePtr->HdmiRxRefClkHz;
+			}
+		}
+		else {
+			PllRefClkHz = XHdmiphy1_GetQuadRefClkFreq(InstancePtr,
+							QuadId,
+							PllPtr->PllRefClkSel);
+		}
+	}
+
+	PllxVcoRateHz = (u64)(PllRefClkHz *
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(ChId)].
+						PllParams.N1FbDiv *
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(ChId)].
+						PllParams.N2FbDiv) /
+		InstancePtr->Quads[QuadId].Plls[XHDMIPHY1_CH2IDX(ChId)].
+						PllParams.MRefClkDiv;
+
+	return PllxVcoRateHz;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the number of active reference clock sources
+* based in the CFG
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	No of active REFCLK sources
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XHdmiphy1_GetRefClkSourcesCount(XHdmiphy1 *InstancePtr)
+{
+	u8 RefClkNum = 0;
+	u8 RefClkNumMax = 5;
+	XHdmiphy1_PllRefClkSelType RefClkSel[RefClkNumMax];
+	XHdmiphy1_PllRefClkSelType RefClkSelTemp[RefClkNumMax];
+	u8 i, j, Match;
+
+	/* TxRefClkSel */
+	RefClkSel[0] = (InstancePtr->Config.TxProtocol !=
+                        XHDMIPHY1_PROTOCOL_NONE) ?
+                            InstancePtr->Config.TxRefClkSel : 99;
+	/* RxRefClkSel */
+	RefClkSel[1] = (InstancePtr->Config.RxProtocol !=
+                        XHDMIPHY1_PROTOCOL_NONE) ?
+                            InstancePtr->Config.RxRefClkSel : 99;
+	/* DruRefClkSel */
+	RefClkSel[2] = (InstancePtr->Config.DruIsPresent) ?
+                            InstancePtr->Config.DruRefClkSel : 99;
+	/* TxFrlRefClkSel */
+	RefClkSel[3] = (InstancePtr->Config.TxProtocol ==
+                        XHDMIPHY1_PROTOCOL_HDMI21) ?
+                            InstancePtr->Config.TxFrlRefClkSel : 99;
+	/* RxFrlRefClkSel */
+	RefClkSel[4] = (InstancePtr->Config.RxProtocol ==
+                        XHDMIPHY1_PROTOCOL_HDMI21) ?
+                            InstancePtr->Config.RxFrlRefClkSel : 99;
+
+	/* Initialize Unique RefClk holder */
+	for (i=0; i<RefClkNumMax; i++) {
+		RefClkSelTemp[i] = 99;
+	}
+
+	i = 0;
+	do {
+		if (RefClkSel[i] != 99) {
+			Match = 0;
+			j = 0;
+			/* Check if RefClkSel is already in Unique Holder array */
+			do {
+				if (RefClkSelTemp[j] == RefClkSel[i]) {
+					Match |= 1;
+				}
+				j++;
+			} while (j<RefClkNum);
+
+			/* Register in Unique Holder if new RefClk is detected */
+			if (Match == 0) {
+				RefClkSelTemp[RefClkNum] = RefClkSel[i];
+				/* Increment RefClk counter */
+				RefClkNum++;
+			}
+		}
+		i++;
+	} while (i<RefClkNumMax);
+
+	return RefClkNum;
+}
+#endif
+
+#ifdef __cplusplus
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to set the clock and data recovery
+* (CDR) values for a given channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_CfgSetCdr(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->CfgSetCdr(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to check if a given PLL output
+* frequency is within the operating range of the PLL for the GT type.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	PllClkOutFreqHz is the frequency to check.
+*
+* @return
+*		- XST_SUCCESS if the frequency resides within the PLL's range.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_CheckPllOpRange(XHdmiphy1 *InstancePtr, u8 QuadId,
+				XHdmiphy1_ChannelId ChId,
+				u64 PllClkOutFreqHz)
+{
+	return InstancePtr->GtAdaptor->CheckPllOpRange(InstancePtr,
+							QuadId, ChId,
+							PllClkOutFreqHz);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to set the output divider logic for
+* a given channel.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_OutDivChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir)
+{
+	return InstancePtr->GtAdaptor->OutDivChReconfig(InstancePtr, QuadId,
+							ChId, Dir);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the channel
+* clock settings.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_ClkChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->ClkChReconfig(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the common channel
+* clock settings.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	CmnId is the common channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_ClkCmnReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->ClkCmnReconfig(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the channel's
+* RX settings.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_RxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->RxChReconfig(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the channel's
+* TX settings.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_TxChReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->TxChReconfig(InstancePtr, QuadId, ChId);
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function checks if Instance is HDMI 2.0 or HDMI 2.1
+*
+* @param	InstancePtr is a pointer to the HDMIPHY instance.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	TRUE if HDMI 2.0 or 2.1 else FALSE.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XHdmiphy1_IsHDMI(XHdmiphy1 *InstancePtr, XHdmiphy1_DirectionType Dir)
+{
+	if (Dir == XHDMIPHY1_DIR_TX) {
+		if ((InstancePtr->Config.TxProtocol == XHDMIPHY1_PROTOCOL_HDMI) ||
+			(InstancePtr->Config.TxProtocol == XHDMIPHY1_PROTOCOL_HDMI21)) {
+			return TRUE;
+		}
+	} else { /* Dir == XHDMIPHY1_DIR_RX */
+		if ((InstancePtr->Config.RxProtocol == XHDMIPHY1_PROTOCOL_HDMI) ||
+			(InstancePtr->Config.RxProtocol == XHDMIPHY1_PROTOCOL_HDMI21)) {
+			return TRUE;
+		}
+	}
+
+	return FALSE;
+}
+
+/*****************************************************************************/
+/**
+* This function is the error condition handler
+*
+* @param	InstancePtr is a pointer to the HDMIPHY instance.
+* @param    ErrIrqType is the error type
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_ErrorHandler(XHdmiphy1 *InstancePtr)
+{
+	if (InstancePtr->ErrorCallback != NULL) {
+		InstancePtr->ErrorCallback(InstancePtr->ErrorRef);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_i.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_i.h
@@ -0,0 +1,172 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_i.h
+ *
+ * Contains generic APIs that are locally called or used within the
+ * HDMIPHY driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * 1.1   ku   17/05/20 Adding uniquification to avoid clash with vphy
+ * </pre>
+ *
+ * @addtogroup xhdmiphy1_v2_2
+ * @{
+*******************************************************************************/
+
+#ifndef XHDMIPHY1_I_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XHDMIPHY1_I_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xil_assert.h"
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_hw.h"
+#include "xvidc.h"
+
+/****************************** Type Definitions ******************************/
+
+
+/**************************** Function Prototypes *****************************/
+
+
+void XHdmiphy1_Ch2Ids(XHdmiphy1 *InstancePtr, XHdmiphy1_ChannelId ChId,
+		u8 *Id0, u8 *Id1);
+u32 XHdmiphy1_DirReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+XHdmiphy1_SysClkDataSelType XHdmiphy1_Pll2SysClkData(XHdmiphy1_PllType PllSelect);
+XHdmiphy1_SysClkOutSelType XHdmiphy1_Pll2SysClkOut(XHdmiphy1_PllType PllSelect);
+u32 XHdmiphy1_PllCalculator(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+		u32 PllClkInFreqHz);
+
+/* xhdmiphy1.c: Channel configuration functions - setters. */
+u32 XHdmiphy1_WriteCfgRefClkSelReg(XHdmiphy1 *InstancePtr, u8 QuadId);
+void XHdmiphy1_CfgPllRefClkSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_PllRefClkSelType RefClkSel);
+void XHdmiphy1_CfgSysClkDataSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+	XHdmiphy1_DirectionType Dir, XHdmiphy1_SysClkDataSelType SysClkDataSel);
+void XHdmiphy1_CfgSysClkOutSel(XHdmiphy1 *InstancePtr, u8 QuadId,
+	XHdmiphy1_DirectionType Dir, XHdmiphy1_SysClkOutSelType SysClkOutSel);
+
+u32 XHdmiphy1_ClkCalcParams(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        u32 PllClkInFreqHz);
+u32 XHdmiphy1_OutDivReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+u32 XHdmiphy1_ClkReconfig(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+#endif
+
+/* xhdmiphy1.c: Channel configuration functions - getters. */
+XHdmiphy1_ChannelId XHdmiphy1_GetRcfgChId(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, XHdmiphy1_PllType PllType);
+u32 XHdmiphy1_IsPllLocked(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+u32 XHdmiphy1_GetQuadRefClkFreq(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_PllRefClkSelType RefClkType);
+XHdmiphy1_SysClkDataSelType XHdmiphy1_GetSysClkDataSel(XHdmiphy1 *InstancePtr,
+        u8 QuadId, XHdmiphy1_DirectionType Dir, XHdmiphy1_ChannelId ChId);
+XHdmiphy1_SysClkOutSelType XHdmiphy1_GetSysClkOutSel(XHdmiphy1 *InstancePtr,
+        u8 QuadId, XHdmiphy1_DirectionType Dir, XHdmiphy1_ChannelId ChId);
+u32 XHdmiphy1_GtUserRdyEnable(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Hold);
+u32 XHdmiphy1_CfgCpllCalPeriodandTol(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir,
+        u32 FreeRunClkFreq);
+#else
+void XHdmiphy1_SetGtLineRateCfg(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+u16 XHdmiphy1_GetGtLineRateCfg(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_SetGpi(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Set);
+u8 XHdmiphy1_GetGpo(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_GtMstReset(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir, u8 Reset);
+u8 XHdmiphy1_CheckLineRateCfg(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+#endif
+
+/* xhdmiphy1.c: GT/MMCM DRP access. */
+u32 XHdmiphy1_MmcmWriteParameters(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_MmcmReset(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir, u8 Hold);
+void XHdmiphy1_MmcmLockedMaskEnable(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, u8 Enable);
+u8 XHdmiphy1_MmcmLocked(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_MmcmSetClkinsel(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_DirectionType Dir, XHdmiphy1_MmcmClkinsel Sel);
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+void XHdmiphy1_SetBufgGtDiv(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_DirectionType Dir, u8 Div);
+/* xhdmiphy1.c Miscellaneous control. */
+u32 XHdmiphy1_PowerDownGtPll(XHdmiphy1 *InstancePtr, u8 QuadId,
+        XHdmiphy1_ChannelId ChId, u8 Hold);
+#endif
+
+/* xhdmiphy1_intr.c: Interrupt handling functions. */
+void XHdmiphy1_SetIntrHandler(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_IntrHandlerType HandlerType,
+	XHdmiphy1_IntrHandler CallbackFunc, void *CallbackRef);
+void XHdmiphy1_IntrEnable(XHdmiphy1 *InstancePtr,
+		XHdmiphy1_IntrHandlerType Intr);
+void XHdmiphy1_IntrDisable(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_IntrHandlerType Intr);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+u64 XHdmiphy1_GetPllVcoFreqHz(XHdmiphy1 *InstancePtr, u8 QuadId,
+		XHdmiphy1_ChannelId ChId, XHdmiphy1_DirectionType Dir);
+u8 XHdmiphy1_GetRefClkSourcesCount(XHdmiphy1 *InstancePtr);
+#endif
+
+u8 XHdmiphy1_IsHDMI(XHdmiphy1 *InstancePtr, XHdmiphy1_DirectionType Dir);
+void XHdmiphy1_HdmiTxTimerTimeoutHandler(XHdmiphy1 *InstancePtr);
+void XHdmiphy1_HdmiRxTimerTimeoutHandler(XHdmiphy1 *InstancePtr);
+
+void XHdmiphy1_ErrorHandler(XHdmiphy1 *InstancePtr);
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDMIPHY1_I_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_intr.c
@@ -0,0 +1,312 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_intr.c
+ *
+ * This file contains functions related to XHdmiphy1 interrupt handling.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function enables interrupts associated with the specified interrupt type
+ *
+ * @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+ * @param	Intr is the interrupt type/mask to enable.
+ *
+ * @return	None.
+ *
+ * @note	None.
+*
+*******************************************************************************/
+void XHdmiphy1_IntrEnable(XHdmiphy1 *InstancePtr,
+		XHdmiphy1_IntrHandlerType Intr)
+{
+	u32 RegVal;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+                XHDMIPHY1_INTR_EN_REG);
+	RegVal |= Intr;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_INTR_EN_REG,
+        RegVal);
+}
+
+/******************************************************************************/
+/**
+ * This function disabled interrupts associated with the specified interrupt
+ * type.
+ *
+ * @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+ * @param	Intr is the interrupt type/mask to disable.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XHdmiphy1_IntrDisable(XHdmiphy1 *InstancePtr,
+		XHdmiphy1_IntrHandlerType Intr)
+{
+	u32 RegVal;
+
+	RegVal = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_INTR_DIS_REG);
+	RegVal |= Intr;
+	XHdmiphy1_WriteReg(InstancePtr->Config.BaseAddr, XHDMIPHY1_INTR_DIS_REG,
+			RegVal);
+}
+
+/******************************************************************************/
+/**
+ * This function installs a callback function for the specified handler type.
+ *
+ * @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+ * @param	HandlerType is the interrupt handler type which specifies which
+ *		interrupt event to attach the callback for.
+ * @param	CallbackFunc is the address to the callback function.
+ * @param	CallbackRef is the user data item that will be passed to the
+ *		callback function when it is invoked.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XHdmiphy1_SetIntrHandler(XHdmiphy1 *InstancePtr,
+        XHdmiphy1_IntrHandlerType HandlerType,
+        XHdmiphy1_IntrHandler CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid((HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE) ||
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_CPLL_LOCK) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_QPLL_LOCK) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_TXALIGN_DONE) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_QPLL1_LOCK) ||
+#else
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE) ||
+#endif
+		(HandlerType ==
+			XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE) ||
+		(HandlerType ==
+			XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT) ||
+		(HandlerType == XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT));
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	switch (HandlerType) {
+	case XHDMIPHY1_INTR_HANDLER_TYPE_TXRESET_DONE:
+		InstancePtr->IntrTxResetDoneHandler = CallbackFunc;
+		InstancePtr->IntrTxResetDoneCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_RXRESET_DONE:
+		InstancePtr->IntrRxResetDoneHandler = CallbackFunc;
+		InstancePtr->IntrRxResetDoneCallbackRef = CallbackRef;
+		break;
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	case XHDMIPHY1_INTR_HANDLER_TYPE_CPLL_LOCK:
+		InstancePtr->IntrCpllLockHandler = CallbackFunc;
+		InstancePtr->IntrCpllLockCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_QPLL_LOCK:
+		InstancePtr->IntrQpllLockHandler = CallbackFunc;
+		InstancePtr->IntrQpllLockCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_TXALIGN_DONE:
+		InstancePtr->IntrTxAlignDoneHandler = CallbackFunc;
+		InstancePtr->IntrTxAlignDoneCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_QPLL1_LOCK:
+		InstancePtr->IntrQpll1LockHandler = CallbackFunc;
+		InstancePtr->IntrQpll1LockCallbackRef = CallbackRef;
+		break;
+#else
+	case XHDMIPHY1_INTR_HANDLER_TYPE_TX_GPO_RISING_EDGE:
+		InstancePtr->IntrTxGpoRisingEdgeHandler = CallbackFunc;
+		InstancePtr->IntrTxGpoRisingEdgeCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_RX_GPO_RISING_EDGE:
+		InstancePtr->IntrRxGpoRisingEdgeHandler = CallbackFunc;
+		InstancePtr->IntrRxGpoRisingEdgeCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_LCPLL_LOCK:
+		InstancePtr->IntrLcpllLockHandler = CallbackFunc;
+		InstancePtr->IntrLcpllLockCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_RPLL_LOCK:
+		InstancePtr->IntrRpllLockHandler = CallbackFunc;
+		InstancePtr->IntrRpllLockCallbackRef = CallbackRef;
+		break;
+#endif
+	case XHDMIPHY1_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE:
+		InstancePtr->IntrTxClkDetFreqChangeHandler =
+							CallbackFunc;
+		InstancePtr->IntrTxClkDetFreqChangeCallbackRef =
+							CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE:
+		InstancePtr->IntrRxClkDetFreqChangeHandler =
+							CallbackFunc;
+		InstancePtr->IntrRxClkDetFreqChangeCallbackRef =
+							CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE:
+		InstancePtr->IntrTxMmcmLockHandler = CallbackFunc;
+		InstancePtr->IntrTxMmcmLockCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE:
+		InstancePtr->IntrRxMmcmLockHandler = CallbackFunc;
+		InstancePtr->IntrRxMmcmLockCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT:
+		InstancePtr->IntrTxTmrTimeoutHandler = CallbackFunc;
+		InstancePtr->IntrTxTmrTimeoutCallbackRef = CallbackRef;
+		break;
+	case XHDMIPHY1_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT:
+		InstancePtr->IntrRxTmrTimeoutHandler = CallbackFunc;
+		InstancePtr->IntrRxTmrTimeoutCallbackRef = CallbackRef;
+		break;
+	default:
+		break;
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function is the interrupt handler for the XHdmiphy1 driver. It will
+ * detect what kind of interrupt has happened, and will invoke the appropriate
+ * callback function.
+ *
+ * @param	InstancePtr is a pointer to the XHdmiphy1 instance.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XHdmiphy1_InterruptHandler(XHdmiphy1 *InstancePtr)
+{
+	u32 IntrStatus;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Determine what kind of interrupts have occurred. */
+	IntrStatus = XHdmiphy1_ReadReg(InstancePtr->Config.BaseAddr,
+			XHDMIPHY1_INTR_STS_REG);
+
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER != XHDMIPHY1_GTYE5)
+	if (IntrStatus & XHDMIPHY1_INTR_CPLL_LOCK_MASK) {
+		InstancePtr->IntrCpllLockHandler(
+				InstancePtr->IntrCpllLockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_QPLL_LOCK_MASK) {
+		InstancePtr->IntrQpllLockHandler(
+				InstancePtr->IntrQpllLockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_QPLL1_LOCK_MASK) {
+		InstancePtr->IntrQpll1LockHandler(
+				InstancePtr->IntrQpll1LockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_TXRESETDONE_MASK) {
+		InstancePtr->IntrTxResetDoneHandler(
+				InstancePtr->IntrTxResetDoneCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_TXALIGNDONE_MASK) {
+		InstancePtr->IntrTxAlignDoneHandler(
+				InstancePtr->IntrTxAlignDoneCallbackRef);
+	}
+#else
+	if (IntrStatus & XHDMIPHY1_INTR_TXGPO_RE_MASK) {
+		InstancePtr->IntrTxGpoRisingEdgeHandler(
+				InstancePtr->IntrTxGpoRisingEdgeCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_RXGPO_RE_MASK) {
+		InstancePtr->IntrRxGpoRisingEdgeHandler(
+				InstancePtr->IntrRxGpoRisingEdgeCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_LCPLL_LOCK_MASK) {
+		InstancePtr->IntrLcpllLockHandler(
+				InstancePtr->IntrLcpllLockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_RPLL_LOCK_MASK) {
+		InstancePtr->IntrRpllLockHandler(
+				InstancePtr->IntrRpllLockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_TXRESETDONE_MASK) {
+		InstancePtr->IntrTxResetDoneHandler(
+				InstancePtr->IntrTxResetDoneCallbackRef);
+	}
+#endif
+	if (IntrStatus & XHDMIPHY1_INTR_RXRESETDONE_MASK) {
+		InstancePtr->IntrRxResetDoneHandler(
+				InstancePtr->IntrRxResetDoneCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_TXCLKDETFREQCHANGE_MASK) {
+		InstancePtr->IntrTxClkDetFreqChangeHandler(
+				InstancePtr->IntrTxClkDetFreqChangeCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_RXCLKDETFREQCHANGE_MASK) {
+		InstancePtr->IntrRxClkDetFreqChangeHandler(
+				InstancePtr->IntrRxClkDetFreqChangeCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_TXMMCMUSRCLK_LOCK_MASK) {
+		InstancePtr->IntrTxMmcmLockHandler(
+				InstancePtr->IntrTxMmcmLockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_RXMMCMUSRCLK_LOCK_MASK) {
+		InstancePtr->IntrRxMmcmLockHandler(
+				InstancePtr->IntrRxMmcmLockCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_TXTMRTIMEOUT_MASK) {
+		InstancePtr->IntrTxTmrTimeoutHandler(
+				InstancePtr->IntrTxTmrTimeoutCallbackRef);
+	}
+	if (IntrStatus & XHDMIPHY1_INTR_RXTMRTIMEOUT_MASK) {
+		InstancePtr->IntrRxTmrTimeoutHandler(
+				InstancePtr->IntrRxTmrTimeoutCallbackRef);
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_log.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_log.c
@@ -0,0 +1,608 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1.c
+ *
+ * Contains a minimal set of functions for the XHdmiphy1 driver that allow
+ * access to all of the Video PHY core's functionality. See xhdmiphy1.h for a
+ * detailed description of the driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+
+/************************** Constant Definitions *****************************/
+#define ANSI_COLOR_RED     "\x1b[31m"
+#define ANSI_COLOR_GREEN   "\x1b[32m"
+#define ANSI_COLOR_YELLOW  "\x1b[33m"
+#define ANSI_COLOR_BLUE    "\x1b[34m"
+#define ANSI_COLOR_MAGENTA "\x1b[35m"
+#define ANSI_COLOR_CYAN    "\x1b[36m"
+#define ANSI_COLOR_WHITE   "\x1b[37m"
+#define ANSI_COLOR_RESET   "\x1b[0m"
+
+
+/**************************** Function Prototypes *****************************/
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function will reset the driver's logginc mechanism.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_LogReset(XHdmiphy1 *InstancePtr)
+{
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Log.HeadIndex = 0;
+	InstancePtr->Log.TailIndex = 0;
+#endif
+}
+
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+/*****************************************************************************/
+/**
+* This function will insert an event in the driver's logginc mechanism.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	Evt is the event type to log.
+* @param	Data is the associated data for the event.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XHdmiphy1_LogWrite(XHdmiphy1 *InstancePtr, XHdmiphy1_LogEvent Evt,
+        u8 Data)
+{
+	u64 TimeUnit = 0;
+
+	if (InstancePtr->LogWriteCallback) {
+		TimeUnit = InstancePtr->LogWriteCallback(InstancePtr->LogWriteRef);
+	}
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Evt <= (XHDMIPHY1_LOG_EVT_DUMMY));
+	Xil_AssertVoid(Data < 0xFF);
+
+	/* Write data and event into log buffer */
+	InstancePtr->Log.DataBuffer[InstancePtr->Log.HeadIndex] =
+			(Data << 8) | Evt;
+	InstancePtr->Log.TimeRecord[InstancePtr->Log.HeadIndex] = TimeUnit;
+
+	/* Update head pointer if reached to end of the buffer */
+	if (InstancePtr->Log.HeadIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) /
+            sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+		/* Clear pointer */
+		InstancePtr->Log.HeadIndex = 0;
+	}
+	else {
+		/* Increment pointer */
+		InstancePtr->Log.HeadIndex++;
+	}
+
+	/* Check tail pointer. When the two pointer are equal, then the buffer
+	 * is full. In this case then increment the tail pointer as well to
+	 * remove the oldest entry from the buffer. */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) /
+            sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will read the last event from the log.
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+*
+* @return	The log data.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XHdmiphy1_LogRead(XHdmiphy1 *InstancePtr)
+{
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+	u16 Log;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if there is any data in the log */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		Log = 0;
+	}
+	else {
+		Log = InstancePtr->Log.DataBuffer[InstancePtr->Log.TailIndex];
+
+		/* Increment tail pointer */
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) /
+            sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+
+	return Log;
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function will print the entire log to the passed buffer.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	buff Buffer to print to
+* @param	buff_size size off buff passed
+*
+* @return	number of bytes written to buff.
+*
+* @note		None.
+*
+******************************************************************************/
+int XHdmiphy1_LogShow(XHdmiphy1 *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+#ifdef XV_HDMIPHY1_LOG_ENABLE
+	u32 Log;
+	u8 Evt;
+	u8 Data;
+	u64 TimeUnit;
+
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	strSize = scnprintf(buff, buff_size,
+			"\r\n\n\nHDMIPHY log\r\n" \
+			"------\r\n");
+
+	/* Read time record */
+	TimeUnit = InstancePtr->Log.TimeRecord[InstancePtr->Log.TailIndex];
+
+	/* Read log data */
+	Log = XHdmiphy1_LogRead(InstancePtr);
+
+	while (Log != 0 && (buff_size - strSize) > 30 ) {
+		/* Event */
+		Evt = Log & 0xff;
+
+		/* Data */
+		Data = (Log >> 8) & 0xFF;
+
+		switch (Evt) {
+		case (XHDMIPHY1_LOG_EVT_NONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"GT log end\r\n-------\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_QPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL enable (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_QPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_CPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"CPLL enable (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_CPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"CPLL reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_TXPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX MMCM enable (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_TXPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX MMCM reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_RXPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX MMCM enable (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_RXPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX MMCM reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_GTRX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"GT RX reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_GTTX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"GT TX reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_VID_TX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Video TX reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_VID_RX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Video RX reset (%0d)\r\n", Data);
+			break;
+		case (XHDMIPHY1_LOG_EVT_TX_ALIGN):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX alignment done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX alignment start.\r\n.");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_TX_ALIGN_TMOUT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX alignment watchdog timed out.\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_TX_TMR):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX timer event\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX timer load\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_RX_TMR):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX timer event\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX timer load\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_CPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_TX_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT TX reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT TX reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_RX_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT RX reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT RX reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_QPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_INIT):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT init done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT init start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_TXPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_RXPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM reconfig start\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_QPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL lost lock\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_CPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL lost lock\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_LCPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"LCPLL lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"LCPLL lost lock\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_RPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RPLL lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RPLL lost lock\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_RXPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM lost lock\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_TXPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM lost lock\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_TX_RST_DONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX reset done\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_RX_RST_DONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX reset done\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_TX_FREQ):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX frequency event\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_RX_FREQ):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX frequency event\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_DRU_EN):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX DRU enable\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX DRU disable\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_TXGPO_RE):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX GPO Rising Edge Detected\r\n");
+			} else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX MSTRESET Toggled\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_RXGPO_RE):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX GPO Rising Edge Detected\r\n");
+			} else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX MSTRESET Toggled\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_FRL_RECONFIG):
+			if (Data == XHDMIPHY1_DIR_RX) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX FRL Reconfig\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX FRL Reconfig\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_TMDS_RECONFIG):
+			if (Data == XHDMIPHY1_DIR_RX) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX TMDS Reconfig\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX TMDS Reconfig\r\n");
+			}
+			break;
+		case (XHDMIPHY1_LOG_EVT_1PPC_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! The HDMIPHY cannot support this video ");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"format at PPC = 1\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_PPC_MSMTCH_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! HDMI TX SS PPC value, doesn't match with"
+					" HDMIPHY PPC value\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_VDCLK_HIGH_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! Video PHY cannot"
+					"support resolutions with video clock"
+					" > 148.5 MHz.\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_NO_DRU):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Warning: No DRU instance. ");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Low resolution video isn't supported in this "
+					"design.\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_QPLL_CFG_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! QPLL config not found!\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_CPLL_CFG_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! CPLL config not found!\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_LCPLL_CFG_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! LCPLL config not found!\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_GT_RPLL_CFG_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! RPLL config not found!\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_VD_NOT_SPRTD_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: This video format "
+					"is not supported by this device\r\n");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Change to another format\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_MMCM_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! MMCM config not found!\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_HDMI20_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error!  The Video PHY doesn't "
+					"support HDMI 2.0 line rates\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_NO_QPLL_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error!  There's no QPLL instance in the design\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_DRU_CLK_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Wrong DRU REFCLK frequency detected\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_USRCLK_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error! User Clock frequency is more than 300 MHz\r\n");
+			break;
+		case (XHDMIPHY1_LOG_EVT_SPDGRDE_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error!  %s: Line rates > 8.0 "
+					"Gbps are not supported by -1/-1LV devices"
+					ANSI_COLOR_RESET "\r\n",
+					(Data == XHDMIPHY1_DIR_RX) ? "RX" : "TX");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Unknown event %i\r\n", Evt);
+			break;
+		}
+
+		if((buff_size - strSize) > 30) {
+			/* Read log data */
+			Log = XHdmiphy1_LogRead(InstancePtr);
+		} else {
+			Log = 0;
+		}
+	}
+#else
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"\r\nINFO:: HDMIPHY Log Feature is Disabled \r\n");
+#endif
+    return strSize;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_mmcme5.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_mmcme5.c
@@ -0,0 +1,607 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_mmcme5.c
+ *
+ * Contains a minimal set of functions for the XHdmiphy1 driver that allow
+ * access to all of the Video PHY core's functionality. See xhdmiphy1.h for a
+ * detailed description of the driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xstatus.h"
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+#if (XPAR_HDMIPHY1_0_TRANSCEIVER == XHDMIPHY1_GTYE5)
+
+/**************************** Function Prototypes *****************************/
+static u32 XHdmiphy1_Mmcme5DividerEncoding(XHdmiphy1_MmcmDivType DivType,
+		u16 Div);
+static u32 XHdmiphy1_Mmcme5CpResEncoding(u16 Mult);
+static u32 XHdmiphy1_Mmcme5LockReg1Reg2Encoding(u16 Mult);
+
+/************************** Constant Definitions ******************************/
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of ClkFbOutMult optimized for:
+* Phase = 0; Dutycycle = 0.5; No Fractional division
+* The calculations are based on XAPP888
+*
+* @param	Div is the divider to be encoded
+*
+* @return
+*		- Encoded Value for ClkReg1 [15: 0]
+*       - Encoded Value for ClkReg2 [31:16]
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Mmcme5DividerEncoding(XHdmiphy1_MmcmDivType DivType, u16 Div)
+{
+	u32 DrpEnc;
+	u32 ClkReg1;
+    u32 ClkReg2;
+    u8 HiTime, LoTime;
+    u16 Divide = Div;
+
+    if (DivType == XHDMIPHY1_MMCM_CLKOUT_DIVIDE) {
+	/* Div is an odd number */
+		if (Div % 2) {
+		Divide = (Div / 2);
+		}
+		/* Div is an even number */
+		else {
+		Divide = (Div / 2) + (Div % 2);
+		}
+    }
+
+	HiTime = Divide / 2;
+	LoTime = HiTime;
+
+	ClkReg2 = LoTime & 0xFF;
+	ClkReg2 |= (HiTime & 0xFF) << 8;
+
+	if (DivType == XHDMIPHY1_MMCM_CLKFBOUT_MULT_F) {
+		ClkReg1 = (Divide % 2) ? 0x00001700 : 0x00001600;
+	}
+	else {
+		/* Div is an odd number */
+		if (Div % 2) {
+			ClkReg1 = (Divide % 2) ? 0x0000BB00 : 0x0000BA00;
+		}
+		/* Div is an even number */
+		else {
+			ClkReg1 = (Divide % 2) ? 0x00001B00 : 0x00001A00;
+		}
+	}
+
+    DrpEnc = (ClkReg2 << 16) | ClkReg1;
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of CP and Res optimized for:
+* Phase = 0; Dutycycle = 0.5; BW = low; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- [3:0]   CP
+*		- [20:17] RES
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Mmcme5CpResEncoding(u16 Mult)
+{
+	u32 DrpEnc;
+	u16 cp;
+	u16 res;
+
+    switch (Mult) {
+    case 4:
+         cp = 5; res = 15;
+         break;
+    case 5:
+         cp = 6; res = 15;
+         break;
+    case 6:
+         cp = 7; res = 15;
+         break;
+    case 7:
+         cp = 13; res = 15;
+         break;
+    case 8:
+         cp = 14; res = 15;
+         break;
+    case 9:
+         cp = 15; res = 15;
+         break;
+    case 10:
+         cp = 14; res = 7;
+         break;
+    case 11:
+         cp = 15; res = 7;
+         break;
+    case 12 ... 13:
+         cp = 15; res = 11;
+         break;
+    case 14:
+         cp = 15; res = 13;
+         break;
+    case 15:
+         cp = 15; res = 3;
+         break;
+    case 16 ... 17:
+         cp = 14; res = 5;
+         break;
+    case 18 ... 19:
+         cp = 15; res = 5;
+         break;
+    case 20 ... 21:
+         cp = 15; res = 9;
+         break;
+    case 22 ... 23:
+         cp = 14; res = 14;
+         break;
+    case 24 ... 26:
+         cp = 15; res = 14;
+         break;
+    case 27 ... 28:
+         cp = 14; res = 1;
+         break;
+    case 29 ... 33:
+         cp = 15; res = 1;
+         break;
+    case 34 ... 37:
+         cp = 14; res = 6;
+         break;
+    case 38 ... 44:
+         cp = 15; res = 6;
+         break;
+    case 45 ... 57:
+         cp = 15; res = 10;
+         break;
+    case 58 ... 63:
+         cp = 13; res = 12;
+         break;
+    case 64 ... 70:
+         cp = 14; res = 12;
+         break;
+    case 71 ... 86:
+         cp = 15; res = 12;
+         break;
+    case 87 ... 93:
+         cp = 14; res = 2;
+         break;
+    case 94:
+         cp = 5; res = 15;
+         break;
+    case 95:
+         cp = 6; res = 15;
+         break;
+    case 96:
+         cp = 7; res = 15;
+         break;
+    case 97:
+         cp = 13; res = 15;
+         break;
+    case 98:
+         cp = 14; res = 15;
+         break;
+    case 99:
+         cp = 15; res = 15;
+         break;
+    case 100:
+         cp = 14; res = 7;
+         break;
+    case 101:
+         cp = 15; res = 7;
+         break;
+    case 102 ... 103:
+         cp = 15; res = 11;
+         break;
+    case 104:
+         cp = 15; res = 13;
+         break;
+    case 105:
+         cp = 15; res = 3;
+         break;
+    case 106 ... 107:
+         cp = 14; res = 5;
+         break;
+    case 108 ... 109:
+         cp = 15; res = 5;
+         break;
+    case 110 ... 111:
+         cp = 15; res = 9;
+         break;
+    case 112 ... 113:
+         cp = 14; res = 14;
+         break;
+    case 114 ... 116:
+         cp = 15; res = 14;
+         break;
+    case 117 ... 118:
+         cp = 14; res = 1;
+         break;
+    case 119 ... 123:
+         cp = 15; res = 1;
+         break;
+    case 124 ... 127:
+         cp = 14; res = 6;
+         break;
+    case 128 ... 134:
+         cp = 15; res = 6;
+         break;
+    case 135 ... 147:
+         cp = 15; res = 10;
+         break;
+    case 148 ... 153:
+         cp = 13; res = 12;
+         break;
+    case 154 ... 160:
+         cp = 14; res = 12;
+         break;
+    case 161 ... 176:
+         cp = 15; res = 12;
+         break;
+    case 177 ... 183:
+         cp = 14; res = 2;
+         break;
+    case 184 ... 200:
+         cp = 14; res = 4;
+         break;
+    case 201 ... 273:
+         cp = 15; res = 4;
+         break;
+    case 274 ... 300:
+         cp = 13; res = 8;
+         break;
+    case 301 ... 325:
+         cp = 14; res = 8;
+         break;
+    case 326 ... 432:
+         cp = 15; res = 8;
+         break;
+	 default:
+         cp = 13; res = 8;
+	     break;
+	}
+
+    /* Construct the return value */
+    DrpEnc = ((res & 0xf) << 17) | ((cp & 0xf) | 0x160);
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of Lock Reg1 & Reg2 optimized for:
+* Phase = 0; Dutycycle = 0.5; BW = low; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- [15:0]  Lock_1 Reg
+*		- [31:16] Lock_2 Reg
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_Mmcme5LockReg1Reg2Encoding(u16 Mult)
+{
+	u32 DrpEnc;
+	u16 Lock_1;
+	u16 Lock_2;
+	u16 lock_ref_dly;
+	u16 lock_fb_dly;
+	u16 lock_cnt;
+	u16 lock_sat_high = 9;
+
+	switch (Mult) {
+		case 4:
+			lock_ref_dly = 4;
+			lock_fb_dly = 4;
+			lock_cnt = 1000;
+			break;
+		case 5:
+			lock_ref_dly = 6;
+			lock_fb_dly = 6;
+			lock_cnt = 1000;
+			break;
+		case 6 ... 7:
+			lock_ref_dly = 7;
+			lock_fb_dly = 7;
+			lock_cnt = 1000;
+			break;
+		case 8:
+			lock_ref_dly = 9;
+			lock_fb_dly = 9;
+			lock_cnt = 1000;
+			break;
+		case 9 ... 10:
+			lock_ref_dly = 10;
+			lock_fb_dly = 10;
+			lock_cnt = 1000;
+			break;
+		case 11:
+			lock_ref_dly = 11;
+			lock_fb_dly = 11;
+			lock_cnt = 1000;
+			break;
+		case 12:
+			lock_ref_dly = 13;
+			lock_fb_dly = 13;
+			lock_cnt = 1000;
+			break;
+		case 13 ... 14:
+			lock_ref_dly = 14;
+			lock_fb_dly = 14;
+			lock_cnt = 1000;
+			break;
+		case 15:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 900;
+			break;
+		case 16 ... 17:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 825;
+			break;
+		case 18:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 750;
+			break;
+		case 19 ... 20:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 700;
+			break;
+		case 21:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 650;
+			break;
+		case 22 ... 23:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 625;
+			break;
+		case 24:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 575;
+			break;
+		case 25:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 550;
+			break;
+		case 26 ... 28:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 525;
+			break;
+		case 29 ... 30:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 475;
+			break;
+		case 31:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 450;
+			break;
+		case 32 ... 33:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 425;
+			break;
+		case 34 ... 36:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 400;
+			break;
+		case 37:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 375;
+			break;
+		case 38 ... 40:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 350;
+			break;
+		case 41 ... 43:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 325;
+			break;
+		case 44 ... 47:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 300;
+			break;
+		case 48 ... 51:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 275;
+			break;
+		case 52 ... 205:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 950;
+			break;
+		case 206 ... 432:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 925;
+			break;
+		default:
+			lock_ref_dly = 16;
+			lock_fb_dly = 16;
+			lock_cnt = 250;
+			break;
+	}
+
+	/* Construct Lock_1 Reg */
+	Lock_1 = ((lock_fb_dly & 0x1F) << 10) | (lock_cnt & 0x3FF);
+
+	/* Construct Lock_2 Reg */
+	Lock_2 = ((lock_ref_dly & 0x1F) << 10) | (lock_sat_high & 0x3FF);
+
+	/* Construct Return Value */
+	DrpEnc = (Lock_2 << 16) | Lock_1;
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function will write the mixed-mode clock manager (MMCM) values currently
+* stored in the driver's instance structure to hardware .
+*
+* @param	InstancePtr is a pointer to the XHdmiphy1 core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return
+*		- XST_SUCCESS if the MMCM write was successful.
+*		- XST_FAILURE otherwise, if the configuration success bit did
+*		  not go low.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XHdmiphy1_MmcmWriteParameters(XHdmiphy1 *InstancePtr, u8 QuadId,
+							XHdmiphy1_DirectionType Dir)
+{
+	u8 ChId;
+	u32 DrpVal32;
+	u16 DrpRdVal;
+	XHdmiphy1_Mmcm *MmcmParams;
+
+    ChId = (Dir == XHDMIPHY1_DIR_TX) ?
+						XHDMIPHY1_CHANNEL_ID_TXMMCM :
+						XHDMIPHY1_CHANNEL_ID_RXMMCM;
+
+	MmcmParams = &InstancePtr->Quads[QuadId].Mmcm[Dir];
+
+	/* Check Parameters if has been Initialized */
+	if (!MmcmParams->DivClkDivide && !MmcmParams->ClkFbOutMult &&
+			!MmcmParams->ClkOut0Div && !MmcmParams->ClkOut1Div &&
+			!MmcmParams->ClkOut2Div) {
+		return XST_FAILURE;
+	}
+
+	/* Write CLKFBOUT_1 & CLKFBOUT_2 Values */
+	DrpVal32 = XHdmiphy1_Mmcme5DividerEncoding(XHDMIPHY1_MMCM_CLKFBOUT_MULT_F,
+						MmcmParams->ClkFbOutMult);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x0C,
+						(u16)(DrpVal32 & 0xFFFF));
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x0D,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write DIVCLK_DIVIDE & DESKEW_2 Values */
+	DrpVal32 = XHdmiphy1_Mmcme5DividerEncoding(XHDMIPHY1_MMCM_DIVCLK_DIVIDE,
+						MmcmParams->DivClkDivide) ;
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x21,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x20,
+						((MmcmParams->DivClkDivide == 0) ? 0x0000 :
+								((MmcmParams->DivClkDivide % 2) ?
+                                    0x0400 : 0x0000)));
+
+	/* Write CLKOUT0_1 & CLKOUT0_2 Values */
+	DrpVal32 = XHdmiphy1_Mmcme5DividerEncoding(XHDMIPHY1_MMCM_CLKOUT_DIVIDE,
+						MmcmParams->ClkOut0Div);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x0E,
+						(u16)(DrpVal32 & 0xFFFF));
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x0F,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write CLKOUT1_1 & CLKOUT1_2 Values */
+	DrpVal32 = XHdmiphy1_Mmcme5DividerEncoding(XHDMIPHY1_MMCM_CLKOUT_DIVIDE,
+						MmcmParams->ClkOut1Div);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x10,
+						(u16)(DrpVal32 & 0xFFFF));
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x11,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write CLKOUT2_1 & CLKOUT2_2 Values */
+	DrpVal32 = XHdmiphy1_Mmcme5DividerEncoding(XHDMIPHY1_MMCM_CLKOUT_DIVIDE,
+						MmcmParams->ClkOut2Div);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x12,
+						(u16)(DrpVal32 & 0xFFFF));
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x13,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write CP & RES Values */
+	DrpVal32 = XHdmiphy1_Mmcme5CpResEncoding(MmcmParams->ClkFbOutMult);
+	/* CP */
+	DrpRdVal = XHdmiphy1_DrpRd(InstancePtr, QuadId, ChId, 0x1E, &DrpRdVal);
+	DrpRdVal &= ~(0xF);
+
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x1E,
+						(u16)((DrpVal32 & 0xF) | DrpRdVal));
+
+	/* RES */
+	DrpRdVal = XHdmiphy1_DrpRd(InstancePtr, QuadId, ChId, 0x2A, &DrpRdVal);
+	DrpRdVal &= ~(0x1E);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x2A,
+						(u16)(((DrpVal32 >> 15) & 0x1E) | DrpRdVal));
+
+	/* Write Lock Reg1 & Reg2 Values */
+	DrpVal32 = XHdmiphy1_Mmcme5LockReg1Reg2Encoding(MmcmParams->ClkFbOutMult);
+	/* LOCK_1 */
+	DrpRdVal = XHdmiphy1_DrpRd(InstancePtr, QuadId, ChId, 0x27, &DrpRdVal);
+	DrpRdVal &= ~(0x8000);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x27,
+						(u16)((DrpVal32 & 0x7FFF) | DrpRdVal));
+
+	/* LOCK_2 */
+	DrpRdVal = XHdmiphy1_DrpRd(InstancePtr, QuadId, ChId, 0x28, &DrpRdVal);
+	DrpRdVal &= ~(0x8000);
+	XHdmiphy1_DrpWr(InstancePtr, QuadId, ChId, 0x28,
+						(u16)(((DrpVal32 >> 16) & 0x7FFF) | DrpRdVal));
+
+	return XST_SUCCESS;
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xhdmiphy1_sinit.c
@@ -0,0 +1,83 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmiphy1_sinit.c
+ *
+ * This file contains static initialization methods for the XHdmiphy1 driver.
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ *            dd/mm/yy
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/12/18 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xhdmiphy1.h"
+#include "xhdmiphy1_i.h"
+
+/*************************** Variable Declarations ****************************/
+
+#ifndef XPAR_XHDMIPHY1_NUM_INSTANCES
+#define XPAR_XHDMIPHY1_NUM_INSTANCES 0
+#endif
+
+/**
+ * A table of configuration structures containing the configuration information
+ * for each Video PHY core in the system.
+ */
+extern XHdmiphy1_Config XHdmiphy1_ConfigTable[XPAR_XHDMIPHY1_NUM_INSTANCES];
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function looks for the device configuration based on the unique device
+ * ID. The table XHdmiphy1_ConfigTable[] contains the configuration information
+ * for each device in the system.
+ *
+ * @param	DeviceId is the unique device ID of the device being looked up.
+ *
+ * @return	A pointer to the configuration table entry corresponding to the
+ *		given device ID, or NULL if no match is found.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+XHdmiphy1_Config *XHdmiphy1_LookupConfig(u16 DeviceId)
+{
+	XHdmiphy1_Config *CfgPtr = NULL;
+	u32 Index;
+
+	for (Index = 0; Index < XPAR_XHDMIPHY1_NUM_INSTANCES; Index++) {
+		if (XHdmiphy1_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XHdmiphy1_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return CfgPtr;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_assert.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_assert.h
@@ -0,0 +1,74 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xil_assert.h
+*
+* This file contains assert related functions.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date   Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00a hbm  07/14/09 First release
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XIL_ASSERT_H	/* prevent circular inclusions */
+#define XIL_ASSERT_H	/* by using protection macros */
+
+#include "xil_types.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+
+/************************** Constant Definitions *****************************/
+
+#define XIL_ASSERT_NONE     0U
+#define XIL_ASSERT_OCCURRED 1U
+#define XNULL NULL
+
+/**
+ * This data type defines a callback to be invoked when an
+ * assert occurs. The callback is invoked only when asserts are enabled
+ */
+//typedef void (*Xil_AssertCallback) (const char8 *File, s32 Line);
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+//#define Xil_Assert(const char8 *File, s32 Line)
+//#define Xil_AssertSetCallback(Xil_AssertCallback Routine)
+
+#define Xil_AssertVoid(Expression)
+#define Xil_AssertVoidAlways()
+#define Xil_AssertNonvoid(Expression)
+#define Xil_AssertNonvoidAlways()
+
+
+/************************** Function Prototypes ******************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif	/* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_io.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_io.h
@@ -0,0 +1,56 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xil_io.h
+*
+* This file contains the interface for the general IO component, which
+* encapsulates the Input/Output functions for processors that do not
+* require any special I/O handling.
+*
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who      Date     Changes
+* ----- -------- -------- -----------------------------------------------
+* 5.00 	pkp  	 05/29/14 First release
+* </pre>
+******************************************************************************/
+
+#ifndef XIL_IO_H           /* prevent circular inclusions */
+#define XIL_IO_H           /* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_types.h"
+#include <linux/io.h>
+
+static inline void Xil_Out32(INTPTR Addr, u32 Value)
+{
+	iowrite32(Value, (volatile void *)Addr);
+}
+static inline u32 Xil_In32(INTPTR Addr)
+{
+	return ioread32((const volatile void *)Addr);
+}
+
+#endif /* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_printf.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_printf.h
@@ -0,0 +1,66 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+
+ #ifndef XIL_PRINTF_H
+ #define XIL_PRINTF_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#ifndef __KERNEL__
+#include <ctype.h>
+#include <string.h>
+#include <stdarg.h>
+#endif
+#include "xil_types.h"
+
+
+/*----------------------------------------------------*/
+/* Use the following parameter passing structure to   */
+/* make xil_printf re-entrant.                        */
+/*----------------------------------------------------*/
+
+struct params_s;
+
+
+/*---------------------------------------------------*/
+/* The purpose of this routine is to output data the */
+/* same as the standard printf function without the  */
+/* overhead most run-time libraries involve. Usually */
+/* the printf brings in many kilobytes of code and   */
+/* that is unacceptable in most embedded systems.    */
+/*---------------------------------------------------*/
+
+typedef char8* charptr;
+typedef s32 (*func_ptr)(int c);
+
+/*                                                   */
+
+void xil_printf( const char8 *ctrl1, ...);
+void print( const char8 *ptr);
+extern void outbyte (char8 c);
+extern char8 inbyte(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#include <linux/module.h> 
+#define xil_printf(format, ...) printk(KERN_INFO format, ## __VA_ARGS__) 
+#define print(format) printk(KERN_INFO format)
+
+#endif	/* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_types.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xil_types.h
@@ -0,0 +1,198 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xil_types.h
+*
+*
+* The xil_types.h file contains basic types for Xilinx software IP. These data types
+* are applicable for all processors supported by Xilinx.
+* @{
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date   Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00a hbm  07/14/09 First release
+* 3.03a sdm  05/30/11 Added Xuint64 typedef and XUINT64_MSW/XUINT64_LSW macros
+* 5.00 	pkp  05/29/14 Made changes for 64 bit architecture
+*	srt  07/14/14 Use standard definitions from stdint.h and stddef.h
+*		      Define LONG and ULONG datatypes and mask values
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XIL_TYPES_H	/* prevent circular inclusions */
+#define XIL_TYPES_H	/* by using protection macros */
+
+#ifndef __KERNEL__
+#include <stdint.h>
+#include <stddef.h>
+#endif
+
+/************************** Constant Definitions *****************************/
+
+#ifndef TRUE
+#  define TRUE		1U
+#endif
+
+#ifndef FALSE
+#  define FALSE		0U
+#endif
+
+#ifndef NULL
+#define NULL ((void *)0)
+#endif
+
+#define XIL_COMPONENT_IS_READY     0x11111111U  /**< In device drivers, This macro will be
+                                                 assigend to "IsReady" member of driver
+												 instance to indicate that driver
+												 instance is initialized and ready to use. */
+#define XIL_COMPONENT_IS_STARTED   0x22222222U  /**< In device drivers, This macro will be assigend to
+                                                 "IsStarted" member of driver instance
+												 to indicate that driver instance is
+												 started and it can be enabled. */
+
+/* @name New types
+ * New simple types.
+ * @{
+ */
+#ifndef __KERNEL__
+#ifndef XBASIC_TYPES_H
+/*
+ * guarded against xbasic_types.h.
+ */
+typedef uint8_t u8;
+typedef uint16_t u16;
+typedef uint32_t u32;
+/** @}*/
+#define __XUINT64__
+typedef struct
+{
+	u32 Upper;
+	u32 Lower;
+} Xuint64;
+
+
+/*****************************************************************************/
+/**
+* @brief    Return the most significant half of the 64 bit data type.
+*
+* @param    x is the 64 bit word.
+*
+* @return   The upper 32 bits of the 64 bit word.
+*
+******************************************************************************/
+#define XUINT64_MSW(x) ((x).Upper)
+
+/*****************************************************************************/
+/**
+* @brief    Return the least significant half of the 64 bit data type.
+*
+* @param    x is the 64 bit word.
+*
+* @return   The lower 32 bits of the 64 bit word.
+*
+******************************************************************************/
+#define XUINT64_LSW(x) ((x).Lower)
+
+#endif /* XBASIC_TYPES_H */
+
+/*
+ * xbasic_types.h does not typedef s* or u64
+ */
+/** @{ */
+typedef char char8;
+typedef int8_t s8;
+typedef int16_t s16;
+typedef int32_t s32;
+typedef int64_t s64;
+typedef uint64_t u64;
+typedef int sint32;
+
+typedef intptr_t INTPTR;
+typedef uintptr_t UINTPTR;
+typedef ptrdiff_t PTRDIFF;
+/** @}*/
+#if !defined(LONG) || !defined(ULONG)
+typedef long LONG;
+typedef unsigned long ULONG;
+#endif
+
+#define ULONG64_HI_MASK	0xFFFFFFFF00000000U
+#define ULONG64_LO_MASK	~ULONG64_HI_MASK
+
+#else
+#include <linux/types.h>
+// Used by xil_io.h
+typedef char char8;
+typedef long INTPTR;
+typedef uintptr_t UINTPTR;
+typedef ptrdiff_t PTRDIFF;
+#endif
+
+/** @{ */
+/**
+ * This data type defines an interrupt handler for a device.
+ * The argument points to the instance of the component
+ */
+typedef void (*XInterruptHandler) (void *InstancePtr);
+
+/**
+ * This data type defines an exception handler for a processor.
+ * The argument points to the instance of the component
+ */
+typedef void (*XExceptionHandler) (void *InstancePtr);
+
+/**
+ * @brief  Returns 32-63 bits of a number.
+ * @param  n : Number being accessed.
+ * @return Bits 32-63 of number.
+ *
+ * @note    A basic shift-right of a 64- or 32-bit quantity.
+ *          Use this to suppress the "right shift count >= width of type"
+ *          warning when that quantity is 32-bits.
+ */
+#define UPPER_32_BITS(n) ((u32)(((n) >> 16) >> 16))
+
+/**
+ * @brief  Returns 0-31 bits of a number
+ * @param  n : Number being accessed.
+ * @return Bits 0-31 of number
+ */
+#define LOWER_32_BITS(n) ((u32)(n))
+
+
+
+
+/************************** Constant Definitions *****************************/
+
+#ifndef TRUE
+#define TRUE		1U
+#endif
+
+#ifndef FALSE
+#define FALSE		0U
+#endif
+
+#ifndef NULL
+#define NULL ((void *)0)
+#endif
+
+#endif	/* end of protection macro */
+/**
+*/
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xstatus.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xstatus.h
@@ -0,0 +1,517 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xstatus.h
+*
+*
+* The xstatus.h file contains the Xilinx&reg; software status codes.These codes are
+* used throughout the Xilinx device drivers.
+*
+* @{
+******************************************************************************/
+
+#ifndef XSTATUS_H		/* prevent circular inclusions */
+#define XSTATUS_H		/* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_types.h"
+#include "xil_assert.h"
+
+/************************** Constant Definitions *****************************/
+
+/*********************** Common statuses 0 - 500 *****************************/
+/**
+@name Common Status Codes for All Device Drivers
+@{
+*/
+#define XST_SUCCESS                     0L
+#define XST_FAILURE                     1L
+#define XST_DEVICE_NOT_FOUND            2L
+#define XST_DEVICE_BLOCK_NOT_FOUND      3L
+#define XST_INVALID_VERSION             4L
+#define XST_DEVICE_IS_STARTED           5L
+#define XST_DEVICE_IS_STOPPED           6L
+#define XST_FIFO_ERROR                  7L	/*!< An error occurred during an
+						   operation with a FIFO such as
+						   an underrun or overrun, this
+						   error requires the device to
+						   be reset */
+#define XST_RESET_ERROR                 8L	/*!< An error occurred which requires
+						   the device to be reset */
+#define XST_DMA_ERROR                   9L	/*!< A DMA error occurred, this error
+						   typically requires the device
+						   using the DMA to be reset */
+#define XST_NOT_POLLED                  10L	/*!< The device is not configured for
+						   polled mode operation */
+#define XST_FIFO_NO_ROOM                11L	/*!< A FIFO did not have room to put
+						   the specified data into */
+#define XST_BUFFER_TOO_SMALL            12L	/*!< The buffer is not large enough
+						   to hold the expected data */
+#define XST_NO_DATA                     13L	/*!< There was no data available */
+#define XST_REGISTER_ERROR              14L	/*!< A register did not contain the
+						   expected value */
+#define XST_INVALID_PARAM               15L	/*!< An invalid parameter was passed
+						   into the function */
+#define XST_NOT_SGDMA                   16L	/*!< The device is not configured for
+						   scatter-gather DMA operation */
+#define XST_LOOPBACK_ERROR              17L	/*!< A loopback test failed */
+#define XST_NO_CALLBACK                 18L	/*!< A callback has not yet been
+						   registered */
+#define XST_NO_FEATURE                  19L	/*!< Device is not configured with
+						   the requested feature */
+#define XST_NOT_INTERRUPT               20L	/*!< Device is not configured for
+						   interrupt mode operation */
+#define XST_DEVICE_BUSY                 21L	/*!< Device is busy */
+#define XST_ERROR_COUNT_MAX             22L	/*!< The error counters of a device
+						   have maxed out */
+#define XST_IS_STARTED                  23L	/*!< Used when part of device is
+						   already started i.e.
+						   sub channel */
+#define XST_IS_STOPPED                  24L	/*!< Used when part of device is
+						   already stopped i.e.
+						   sub channel */
+#define XST_DATA_LOST                   26L	/*!< Driver defined error */
+#define XST_RECV_ERROR                  27L	/*!< Generic receive error */
+#define XST_SEND_ERROR                  28L	/*!< Generic transmit error */
+#define XST_NOT_ENABLED                 29L	/*!< A requested service is not
+						   available because it has not
+						   been enabled */
+/** @} */
+/***************** Utility Component statuses 401 - 500  *********************/
+/**
+@name Utility Component Status Codes 401 - 500
+@{
+*/
+#define XST_MEMTEST_FAILED              401L	/*!< Memory test failed */
+
+/** @} */
+/***************** Common Components statuses 501 - 1000 *********************/
+/**
+@name Packet Fifo Status Codes 501 - 510
+@{
+*/
+/********************* Packet Fifo statuses 501 - 510 ************************/
+
+#define XST_PFIFO_LACK_OF_DATA          501L	/*!< Not enough data in FIFO   */
+#define XST_PFIFO_NO_ROOM               502L	/*!< Not enough room in FIFO   */
+#define XST_PFIFO_BAD_REG_VALUE         503L	/*!< Self test, a register value
+						   was invalid after reset */
+#define XST_PFIFO_ERROR                 504L	/*!< Generic packet FIFO error */
+#define XST_PFIFO_DEADLOCK              505L	/*!< Packet FIFO is reporting
+						 * empty and full simultaneously
+						 */
+/** @} */
+/**
+@name DMA Status Codes 511 - 530
+@{
+*/
+/************************** DMA statuses 511 - 530 ***************************/
+
+#define XST_DMA_TRANSFER_ERROR          511L	/*!< Self test, DMA transfer
+						   failed */
+#define XST_DMA_RESET_REGISTER_ERROR    512L	/*!< Self test, a register value
+						   was invalid after reset */
+#define XST_DMA_SG_LIST_EMPTY           513L	/*!< Scatter gather list contains
+						   no buffer descriptors ready
+						   to be processed */
+#define XST_DMA_SG_IS_STARTED           514L	/*!< Scatter gather not stopped */
+#define XST_DMA_SG_IS_STOPPED           515L	/*!< Scatter gather not running */
+#define XST_DMA_SG_LIST_FULL            517L	/*!< All the buffer desciptors of
+						   the scatter gather list are
+						   being used */
+#define XST_DMA_SG_BD_LOCKED            518L	/*!< The scatter gather buffer
+						   descriptor which is to be
+						   copied over in the scatter
+						   list is locked */
+#define XST_DMA_SG_NOTHING_TO_COMMIT    519L	/*!< No buffer descriptors have been
+						   put into the scatter gather
+						   list to be commited */
+#define XST_DMA_SG_COUNT_EXCEEDED       521L	/*!< The packet count threshold
+						   specified was larger than the
+						   total # of buffer descriptors
+						   in the scatter gather list */
+#define XST_DMA_SG_LIST_EXISTS          522L	/*!< The scatter gather list has
+						   already been created */
+#define XST_DMA_SG_NO_LIST              523L	/*!< No scatter gather list has
+						   been created */
+#define XST_DMA_SG_BD_NOT_COMMITTED     524L	/*!< The buffer descriptor which was
+						   being started was not committed
+						   to the list */
+#define XST_DMA_SG_NO_DATA              525L	/*!< The buffer descriptor to start
+						   has already been used by the
+						   hardware so it can't be reused
+						 */
+#define XST_DMA_SG_LIST_ERROR           526L	/*!< General purpose list access
+						   error */
+#define XST_DMA_BD_ERROR                527L	/*!< General buffer descriptor
+						   error */
+/** @} */
+/**
+@name IPIF Status Codes Codes 531 - 550
+@{
+*/
+/************************** IPIF statuses 531 - 550 ***************************/
+
+#define XST_IPIF_REG_WIDTH_ERROR        531L	/*!< An invalid register width
+						   was passed into the function */
+#define XST_IPIF_RESET_REGISTER_ERROR   532L	/*!< The value of a register at
+						   reset was not valid */
+#define XST_IPIF_DEVICE_STATUS_ERROR    533L	/*!< A write to the device interrupt
+						   status register did not read
+						   back correctly */
+#define XST_IPIF_DEVICE_ACK_ERROR       534L	/*!< The device interrupt status
+						   register did not reset when
+						   acked */
+#define XST_IPIF_DEVICE_ENABLE_ERROR    535L	/*!< The device interrupt enable
+						   register was not updated when
+						   other registers changed */
+#define XST_IPIF_IP_STATUS_ERROR        536L	/*!< A write to the IP interrupt
+						   status register did not read
+						   back correctly */
+#define XST_IPIF_IP_ACK_ERROR           537L	/*!< The IP interrupt status register
+						   did not reset when acked */
+#define XST_IPIF_IP_ENABLE_ERROR        538L	/*!< IP interrupt enable register was
+						   not updated correctly when other
+						   registers changed */
+#define XST_IPIF_DEVICE_PENDING_ERROR   539L	/*!< The device interrupt pending
+						   register did not indicate the
+						   expected value */
+#define XST_IPIF_DEVICE_ID_ERROR        540L	/*!< The device interrupt ID register
+						   did not indicate the expected
+						   value */
+#define XST_IPIF_ERROR                  541L	/*!< Generic ipif error */
+/** @} */
+
+/****************** Device specific statuses 1001 - 4095 *********************/
+/**
+@name Ethernet Status Codes 1001 - 1050
+@{
+*/
+/********************* Ethernet statuses 1001 - 1050 *************************/
+
+#define XST_EMAC_MEMORY_SIZE_ERROR  1001L	/*!< Memory space is not big enough
+						 * to hold the minimum number of
+						 * buffers or descriptors */
+#define XST_EMAC_MEMORY_ALLOC_ERROR 1002L	/*!< Memory allocation failed */
+#define XST_EMAC_MII_READ_ERROR     1003L	/*!< MII read error */
+#define XST_EMAC_MII_BUSY           1004L	/*!< An MII operation is in progress */
+#define XST_EMAC_OUT_OF_BUFFERS     1005L	/*!< Driver is out of buffers */
+#define XST_EMAC_PARSE_ERROR        1006L	/*!< Invalid driver init string */
+#define XST_EMAC_COLLISION_ERROR    1007L	/*!< Excess deferral or late
+						 * collision on polled send */
+/** @} */
+/**
+@name UART Status Codes 1051 - 1075
+@{
+*/
+/*********************** UART statuses 1051 - 1075 ***************************/
+#define XST_UART
+
+#define XST_UART_INIT_ERROR         1051L
+#define XST_UART_START_ERROR        1052L
+#define XST_UART_CONFIG_ERROR       1053L
+#define XST_UART_TEST_FAIL          1054L
+#define XST_UART_BAUD_ERROR         1055L
+#define XST_UART_BAUD_RANGE         1056L
+
+/** @} */
+/**
+@name IIC Status Codes 1076 - 1100
+@{
+*/
+/************************ IIC statuses 1076 - 1100 ***************************/
+
+#define XST_IIC_SELFTEST_FAILED         1076	/*!< self test failed            */
+#define XST_IIC_BUS_BUSY                1077	/*!< bus found busy              */
+#define XST_IIC_GENERAL_CALL_ADDRESS    1078	/*!< mastersend attempted with   */
+					     /* general call address        */
+#define XST_IIC_STAND_REG_RESET_ERROR   1079	/*!< A non parameterizable reg   */
+					     /* value after reset not valid */
+#define XST_IIC_TX_FIFO_REG_RESET_ERROR 1080	/*!< Tx fifo included in design  */
+					     /* value after reset not valid */
+#define XST_IIC_RX_FIFO_REG_RESET_ERROR 1081	/*!< Rx fifo included in design  */
+					     /* value after reset not valid */
+#define XST_IIC_TBA_REG_RESET_ERROR     1082	/*!< 10 bit addr incl in design  */
+					     /* value after reset not valid */
+#define XST_IIC_CR_READBACK_ERROR       1083	/*!< Read of the control register */
+					     /* didn't return value written */
+#define XST_IIC_DTR_READBACK_ERROR      1084	/*!< Read of the data Tx reg     */
+					     /* didn't return value written */
+#define XST_IIC_DRR_READBACK_ERROR      1085	/*!< Read of the data Receive reg */
+					     /* didn't return value written */
+#define XST_IIC_ADR_READBACK_ERROR      1086	/*!< Read of the data Tx reg     */
+					     /* didn't return value written */
+#define XST_IIC_TBA_READBACK_ERROR      1087	/*!< Read of the 10 bit addr reg */
+					     /* didn't return written value */
+#define XST_IIC_NOT_SLAVE               1088	/*!< The device isn't a slave    */
+/** @} */
+/**
+@name ATMC Status Codes 1101 - 1125
+@{
+*/
+/*********************** ATMC statuses 1101 - 1125 ***************************/
+
+#define XST_ATMC_ERROR_COUNT_MAX    1101L	/*!< the error counters in the ATM
+						   controller hit the max value
+						   which requires the statistics
+						   to be cleared */
+/** @} */
+/**
+@name Flash Status Codes 1126 - 1150
+@{
+*/
+/*********************** Flash statuses 1126 - 1150 **************************/
+
+#define XST_FLASH_BUSY                1126L	/*!< Flash is erasing or programming
+						 */
+#define XST_FLASH_READY               1127L	/*!< Flash is ready for commands */
+#define XST_FLASH_ERROR               1128L	/*!< Flash had detected an internal
+						   error. Use XFlash_DeviceControl
+						   to retrieve device specific codes
+						 */
+#define XST_FLASH_ERASE_SUSPENDED     1129L	/*!< Flash is in suspended erase state
+						 */
+#define XST_FLASH_WRITE_SUSPENDED     1130L	/*!< Flash is in suspended write state
+						 */
+#define XST_FLASH_PART_NOT_SUPPORTED  1131L	/*!< Flash type not supported by
+						   driver */
+#define XST_FLASH_NOT_SUPPORTED       1132L	/*!< Operation not supported */
+#define XST_FLASH_TOO_MANY_REGIONS    1133L	/*!< Too many erase regions */
+#define XST_FLASH_TIMEOUT_ERROR       1134L	/*!< Programming or erase operation
+						   aborted due to a timeout */
+#define XST_FLASH_ADDRESS_ERROR       1135L	/*!< Accessed flash outside its
+						   addressible range */
+#define XST_FLASH_ALIGNMENT_ERROR     1136L	/*!< Write alignment error */
+#define XST_FLASH_BLOCKING_CALL_ERROR 1137L	/*!< Couldn't return immediately from
+						   write/erase function with
+						   XFL_NON_BLOCKING_WRITE/ERASE
+						   option cleared */
+#define XST_FLASH_CFI_QUERY_ERROR     1138L	/*!< Failed to query the device */
+/** @} */
+/**
+@name SPI Status Codes 1151 - 1175
+@{
+*/
+/*********************** SPI statuses 1151 - 1175 ****************************/
+
+#define XST_SPI_MODE_FAULT          1151	/*!< master was selected as slave */
+#define XST_SPI_TRANSFER_DONE       1152	/*!< data transfer is complete */
+#define XST_SPI_TRANSMIT_UNDERRUN   1153	/*!< slave underruns transmit register */
+#define XST_SPI_RECEIVE_OVERRUN     1154	/*!< device overruns receive register */
+#define XST_SPI_NO_SLAVE            1155	/*!< no slave has been selected yet */
+#define XST_SPI_TOO_MANY_SLAVES     1156	/*!< more than one slave is being
+						 * selected */
+#define XST_SPI_NOT_MASTER          1157	/*!< operation is valid only as master */
+#define XST_SPI_SLAVE_ONLY          1158	/*!< device is configured as slave-only
+						 */
+#define XST_SPI_SLAVE_MODE_FAULT    1159	/*!< slave was selected while disabled */
+#define XST_SPI_SLAVE_MODE          1160	/*!< device has been addressed as slave */
+#define XST_SPI_RECEIVE_NOT_EMPTY   1161	/*!< device received data in slave mode */
+
+#define XST_SPI_COMMAND_ERROR       1162	/*!< unrecognised command - qspi only */
+#define XST_SPI_POLL_DONE           1163        /*!< controller completed polling the
+						   device for status */
+/** @} */
+/**
+@name OPB Arbiter Status Codes 1176 - 1200
+@{
+*/
+/********************** OPB Arbiter statuses 1176 - 1200 *********************/
+
+#define XST_OPBARB_INVALID_PRIORITY  1176	/*!< the priority registers have either
+						 * one master assigned to two or more
+						 * priorities, or one master not
+						 * assigned to any priority
+						 */
+#define XST_OPBARB_NOT_SUSPENDED     1177	/*!< an attempt was made to modify the
+						 * priority levels without first
+						 * suspending the use of priority
+						 * levels
+						 */
+#define XST_OPBARB_PARK_NOT_ENABLED  1178	/*!< bus parking by id was enabled but
+						 * bus parking was not enabled
+						 */
+#define XST_OPBARB_NOT_FIXED_PRIORITY 1179	/*!< the arbiter must be in fixed
+						 * priority mode to allow the
+						 * priorities to be changed
+						 */
+/** @} */
+/**
+@name INTC Status Codes 1201 - 1225
+@{
+*/
+/************************ Intc statuses 1201 - 1225 **************************/
+
+#define XST_INTC_FAIL_SELFTEST      1201	/*!< self test failed */
+#define XST_INTC_CONNECT_ERROR      1202	/*!< interrupt already in use */
+/** @} */
+/**
+@name TmrCtr Status Codes 1226 - 1250
+@{
+*/
+/********************** TmrCtr statuses 1226 - 1250 **************************/
+
+#define XST_TMRCTR_TIMER_FAILED     1226	/*!< self test failed */
+/** @} */
+/**
+@name WdtTb Status Codes 1251 - 1275
+@{
+*/
+/********************** WdtTb statuses 1251 - 1275 ***************************/
+
+#define XST_WDTTB_TIMER_FAILED      1251L
+/** @} */
+/**
+@name PlbArb status Codes 1276 - 1300
+@{
+*/
+/********************** PlbArb statuses 1276 - 1300 **************************/
+
+#define XST_PLBARB_FAIL_SELFTEST    1276L
+/** @} */
+/**
+@name Plb2Opb Status Codes 1301 - 1325
+@{
+*/
+/********************** Plb2Opb statuses 1301 - 1325 *************************/
+
+#define XST_PLB2OPB_FAIL_SELFTEST   1301L
+/** @} */
+/**
+@name Opb2Plb Status 1326 - 1350
+@{
+*/
+/********************** Opb2Plb statuses 1326 - 1350 *************************/
+
+#define XST_OPB2PLB_FAIL_SELFTEST   1326L
+/** @} */
+/**
+@name SysAce Status Codes 1351 - 1360
+@{
+*/
+/********************** SysAce statuses 1351 - 1360 **************************/
+
+#define XST_SYSACE_NO_LOCK          1351L	/*!< No MPU lock has been granted */
+/** @} */
+/**
+@name PCI Bridge Status Codes 1361 - 1375
+@{
+*/
+/********************** PCI Bridge statuses 1361 - 1375 **********************/
+
+#define XST_PCI_INVALID_ADDRESS     1361L
+/** @} */
+/**
+@name FlexRay Constants 1400 - 1409
+@{
+*/
+/********************** FlexRay constants 1400 - 1409 *************************/
+
+#define XST_FR_TX_ERROR			1400
+#define XST_FR_TX_BUSY			1401
+#define XST_FR_BUF_LOCKED		1402
+#define XST_FR_NO_BUF			1403
+/** @} */
+/**
+@name USB constants 1410 - 1420
+@{
+*/
+/****************** USB constants 1410 - 1420  *******************************/
+
+#define XST_USB_ALREADY_CONFIGURED	1410
+#define XST_USB_BUF_ALIGN_ERROR		1411
+#define XST_USB_NO_DESC_AVAILABLE	1412
+#define XST_USB_BUF_TOO_BIG		1413
+#define XST_USB_NO_BUF			1414
+/** @} */
+/**
+@name HWICAP constants 1421 - 1429
+@{
+*/
+/****************** HWICAP constants 1421 - 1429  *****************************/
+
+#define XST_HWICAP_WRITE_DONE		1421
+
+/** @} */
+/**
+@name AXI VDMA constants 1430 - 1440
+@{
+*/
+/****************** AXI VDMA constants 1430 - 1440  *****************************/
+
+#define XST_VDMA_MISMATCH_ERROR		1430
+/** @} */
+/**
+@name NAND Flash Status Codes 1441 - 1459
+@{
+*/
+/*********************** NAND Flash statuses 1441 - 1459  *********************/
+
+#define XST_NAND_BUSY			1441L	/*!< Flash is erasing or
+						 * programming
+						 */
+#define XST_NAND_READY			1442L	/*!< Flash is ready for commands
+						 */
+#define XST_NAND_ERROR			1443L	/*!< Flash had detected an
+						 * internal error.
+						 */
+#define XST_NAND_PART_NOT_SUPPORTED	1444L	/*!< Flash type not supported by
+						 * driver
+						 */
+#define XST_NAND_OPT_NOT_SUPPORTED	1445L	/*!< Operation not supported
+						 */
+#define XST_NAND_TIMEOUT_ERROR		1446L	/*!< Programming or erase
+						 * operation aborted due to a
+						 * timeout
+						 */
+#define XST_NAND_ADDRESS_ERROR		1447L	/*!< Accessed flash outside its
+						 * addressible range
+						 */
+#define XST_NAND_ALIGNMENT_ERROR	1448L	/*!< Write alignment error
+						 */
+#define XST_NAND_PARAM_PAGE_ERROR	1449L	/*!< Failed to read parameter
+						 * page of the device
+						 */
+#define XST_NAND_CACHE_ERROR		1450L	/*!< Flash page buffer error
+						 */
+
+#define XST_NAND_WRITE_PROTECTED	1451L	/*!< Flash is write protected
+						 */
+/** @} */
+
+/**************************** Type Definitions *******************************/
+
+typedef s32 XStatus;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
+/**
+*/
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr.c
@@ -0,0 +1,715 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr.c
+* @{
+*
+* Contains required functions for the XTmrCtr driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00a ecm  08/16/01 First release
+* 1.00b jhl  02/21/02 Repartitioned the driver for smaller files
+* 1.10b mta  03/21/07 Updated to new coding style
+* 2.00a ktn  10/30/09 Updated to use HAL API's. _m is removed from all the macro
+*		      definitions.
+* 2.05a adk  15/05/13 Fixed the CR:693066
+*		      Added the IsStartedTmrCtr0/IsStartedTmrCtr1 members to the
+*		      XTmrCtr instance structure.
+*		      The IsStartedTmrCtrX will be assigned XIL_COMPONENT_IS_STARTED in
+*		      the XTmrCtr_Start function.
+*		      The IsStartedTmrCtrX will be cleared in the XTmrCtr_Stop function.
+*		      There will be no Initialization done in the
+*		      XTmrCtr_Initialize if both the timers have already started and
+*		      the XST_DEVICE_IS_STARTED Status is returned.
+*		      Removed the logic in the XTmrCtr_Initialize function
+*		      which was checking the Register Value to know whether
+*		      a timer has started or not.
+* 4.0   als  09/30/15 Updated initialization API.
+* 4.1   sk   11/10/15 Used UINTPTR instead of u32 for Baseaddress CR# 867425.
+*                     Changed the prototype of XTmrCtr_CfgInitialize API.
+* 4.5   cjp  03/22/18 Added APIs to support PWM feature. XTmrCtr_PwmConfigure
+*                     is used to configure PWM to operate for specific period
+*                     and high time. XTmrCtr_PwmEnable and XTmrCtr_PwmDisable
+*                     are used to enable/disable the PWM output.
+* 4.8   dp   02/12/21 Fix compilation errors that arise when -Werror=conversion
+*                     is enabled in compilation flags.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xstatus.h"
+
+#include "xtmrctr.h"
+#include "xtmrctr_i.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+static void XTmrCtr_StubCallback(void *CallBackRef, u8 TmrCtrNumber);
+
+/************************** Variable Definitions *****************************/
+
+/*****************************************************************************/
+/**
+* This function populates the timer counter's configuration structure and sets
+* some configurations defaults.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	ConfigPtr is a pointer to the configuration structure that will
+*		be used to copy the settings from.
+* @param	EffectiveAddr is the device base address in the virtual memory
+*		space. If the address translation is not used, then the physical
+*		address is passed.
+*
+* @return	None.
+*
+* @note		Unexpected errors may occur if the address mapping is changed
+*		after this function is invoked.
+*
+******************************************************************************/
+void XTmrCtr_CfgInitialize(XTmrCtr *InstancePtr, XTmrCtr_Config *ConfigPtr,
+		UINTPTR EffectiveAddr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(ConfigPtr != NULL);
+	Xil_AssertVoid(EffectiveAddr != 0x0);
+
+	InstancePtr->IsReady = 0;
+	InstancePtr->Config = *ConfigPtr;
+
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+	InstancePtr->BaseAddress = EffectiveAddr;
+
+	InstancePtr->Handler = XTmrCtr_StubCallback;
+	InstancePtr->CallBackRef = InstancePtr;
+	InstancePtr->Stats.Interrupts = 0;
+
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+}
+
+/*****************************************************************************/
+/**
+* (Re-)initialzes all timer counters which aren't started already.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+*
+* @return
+*		- XST_SUCCESS if at least one timer counter is stopped.
+*		- XST_DEVICE_IS_STARTED otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XTmrCtr_InitHw(XTmrCtr *InstancePtr)
+{
+	int Status = XST_DEVICE_IS_STARTED;
+	u8 TmrIndex;
+	u32 TmrCtrStarted[XTC_DEVICE_TIMER_COUNT];
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	TmrCtrStarted[0] = InstancePtr->IsStartedTmrCtr0;
+	TmrCtrStarted[1] = InstancePtr->IsStartedTmrCtr1;
+
+	for (TmrIndex = 0; TmrIndex < XTC_DEVICE_TIMER_COUNT; TmrIndex++) {
+		/* Only initialize timers counters which aren't started. */
+		if (TmrCtrStarted[TmrIndex] == XIL_COMPONENT_IS_STARTED) {
+			continue;
+		}
+
+		/* Set the compare register to 0. */
+		XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrIndex,
+				  XTC_TLR_OFFSET, 0);
+		/* Reset the timer and the interrupt. */
+		XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrIndex,
+				  XTC_TCSR_OFFSET,
+				  XTC_CSR_INT_OCCURED_MASK | XTC_CSR_LOAD_MASK);
+		/* Release the reset. */
+		XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrIndex,
+				  XTC_TCSR_OFFSET, 0);
+
+		/* Indicate that at least one timer is not running and has been
+		 * initialized. */
+		Status = XST_SUCCESS;
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* Initializes a specific timer/counter instance/driver. Initialize fields of
+* the XTmrCtr structure, then reset the timer/counter.If a timer is already
+* running then it is not initialized.
+*
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	DeviceId is the unique id of the device controlled by this
+*		XTmrCtr component.  Passing in a device id associates the
+*		generic XTmrCtr component to a specific device, as chosen by
+*		the caller or application developer.
+*
+* @return
+*		- XST_SUCCESS if initialization was successful
+*		- XST_DEVICE_IS_STARTED if the device has already been started
+*		- XST_DEVICE_NOT_FOUND if the device doesn't exist
+*
+* @note		None.
+*
+******************************************************************************/
+int XTmrCtr_Initialize(XTmrCtr *InstancePtr, u16 DeviceId)
+{
+	XTmrCtr_Config *ConfigPtr;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* In case all timer counters are already started, don't proceed with
+	 * re-initialization. */
+	if ((InstancePtr->IsStartedTmrCtr0 == XIL_COMPONENT_IS_STARTED) &&
+	    (InstancePtr->IsStartedTmrCtr1 == XIL_COMPONENT_IS_STARTED)) {
+		return XST_DEVICE_IS_STARTED;
+	}
+
+	/* Retrieve configuration of timer counter core with matching ID. */
+	ConfigPtr = XTmrCtr_LookupConfig(DeviceId);
+	if (!ConfigPtr) {
+		return XST_DEVICE_NOT_FOUND;
+	}
+
+	XTmrCtr_CfgInitialize(InstancePtr, ConfigPtr, ConfigPtr->BaseAddress);
+
+	return XTmrCtr_InitHw(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* Starts the specified timer counter of the device such that it starts running.
+* The timer counter is reset before it is started and the reset value is
+* loaded into the timer counter.
+*
+* If interrupt mode is specified in the options, it is necessary for the caller
+* to connect the interrupt handler of the timer/counter to the interrupt source,
+* typically an interrupt controller, and enable the interrupt within the
+* interrupt controller.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XTmrCtr_Start(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+	u32 ControlStatusReg;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/*
+	 * Read the current register contents such that only the necessary bits
+	 * of the register are modified in the following operations
+	 */
+	ControlStatusReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					      TmrCtrNumber, XTC_TCSR_OFFSET);
+	/*
+	 * Reset the timer counter such that it reloads from the compare
+	 * register and the interrupt is cleared simultaneously, the interrupt
+	 * can only be cleared after reset such that the interrupt condition is
+	 * cleared
+	 */
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TCSR_OFFSET,
+			  XTC_CSR_LOAD_MASK);
+
+
+
+	/*
+	 * Indicate that the timer is started before enabling it
+	 */
+	if (TmrCtrNumber == 0) {
+		InstancePtr->IsStartedTmrCtr0 = XIL_COMPONENT_IS_STARTED;
+	} else {
+		InstancePtr->IsStartedTmrCtr1 = XIL_COMPONENT_IS_STARTED;
+	}
+
+
+	/*
+	 * Remove the reset condition such that the timer counter starts running
+	 * with the value loaded from the compare register
+	 */
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TCSR_OFFSET,
+			  ControlStatusReg | XTC_CSR_ENABLE_TMR_MASK);
+}
+
+/*****************************************************************************/
+/**
+*
+* Stops the timer counter by disabling it.
+*
+* It is the callers' responsibility to disconnect the interrupt handler of the
+* timer_counter from the interrupt source, typically an interrupt controller,
+* and disable the interrupt within the interrupt controller.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XTmrCtr_Stop(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+	u32 ControlStatusReg;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/*
+	 * Read the current register contents
+	 */
+	ControlStatusReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					      TmrCtrNumber, XTC_TCSR_OFFSET);
+	/*
+	 * Disable the timer counter such that it's not running
+	 */
+	ControlStatusReg &= (u32)~(XTC_CSR_ENABLE_TMR_MASK);
+
+	/*
+	 * Write out the updated value to the actual register.
+	 */
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TCSR_OFFSET, ControlStatusReg);
+
+	/*
+	 * Indicate that the timer is stopped
+	 */
+	if (TmrCtrNumber == 0) {
+		InstancePtr->IsStartedTmrCtr0 = 0;
+	} else {
+		InstancePtr->IsStartedTmrCtr1 = 0;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* Get the current value of the specified timer counter.  The timer counter
+* may be either incrementing or decrementing based upon the current mode of
+* operation.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number  with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	The current value for the timer counter.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XTmrCtr_GetValue(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	return XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+				  TmrCtrNumber, XTC_TCR_OFFSET);
+}
+
+/*****************************************************************************/
+/**
+*
+* Set the reset value for the specified timer counter. This is the value
+* that is loaded into the timer counter when it is reset. This value is also
+* loaded when the timer counter is started.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number  with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+* @param	ResetValue contains the value to be used to reset the timer
+*		counter.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XTmrCtr_SetResetValue(XTmrCtr * InstancePtr, u8 TmrCtrNumber,
+			   u32 ResetValue)
+{
+
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TLR_OFFSET, ResetValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* Returns the timer counter value that was captured the last time the external
+* capture input was asserted.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number  with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	The current capture value for the indicated timer counter.
+*
+* @note		None.
+*
+*******************************************************************************/
+u32 XTmrCtr_GetCaptureValue(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	return XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+				  TmrCtrNumber, XTC_TLR_OFFSET);
+}
+
+/*****************************************************************************/
+/**
+*
+* Resets the specified timer counter of the device. A reset causes the timer
+* counter to set it's value to the reset value.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number  with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XTmrCtr_Reset(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+	u32 CounterControlReg;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/*
+	 * Read current contents of the register so it won't be destroyed
+	 */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					       TmrCtrNumber, XTC_TCSR_OFFSET);
+	/*
+	 * Reset the timer by toggling the reset bit in the register
+	 */
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TCSR_OFFSET,
+			  CounterControlReg | XTC_CSR_LOAD_MASK);
+
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TCSR_OFFSET, CounterControlReg);
+}
+
+/*****************************************************************************/
+/**
+*
+* Checks if the specified timer counter of the device has expired. In capture
+* mode, expired is defined as a capture occurred. In compare mode, expired is
+* defined as the timer counter rolled over/under for up/down counting.
+*
+* When interrupts are enabled, the expiration causes an interrupt. This function
+* is typically used to poll a timer counter to determine when it has expired.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number  with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	TRUE if the timer has expired, and FALSE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+int XTmrCtr_IsExpired(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+	u32 CounterControlReg;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/*
+	 * Check if timer is expired
+	 */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					       TmrCtrNumber, XTC_TCSR_OFFSET);
+
+	return ((CounterControlReg & XTC_CSR_INT_OCCURED_MASK) ==
+		XTC_CSR_INT_OCCURED_MASK);
+}
+
+/*****************************************************************************/
+/**
+*
+* Configures timers to generate PWM output.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	PwmPeriod is the period of pwm signal in nano seconds.
+* @param	PwmHighTime is the high time of pwm signal in nano seconds.
+*
+* @return	the duty cycle that will possibly be achieved.
+*
+* @note		This function needs to be called before enabling PWM otherwise
+*		the output of PWM may be indeterminate. Here Down count mode of
+*		timers are used for generating PWM output.
+*
+******************************************************************************/
+u8 XTmrCtr_PwmConfigure(XTmrCtr *InstancePtr, u32 PwmPeriod, u32 PwmHighTime)
+{
+	u32 CounterControlReg;
+	u32 SysClkPeriod;
+	u64 Period;
+	u64 High;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Stop the timers if they are running */
+	if (InstancePtr->IsStartedTmrCtr0 == XIL_COMPONENT_IS_STARTED) {
+		XTmrCtr_Stop(InstancePtr, XTC_TIMER_0);
+	}
+	if (InstancePtr->IsStartedTmrCtr1 == XIL_COMPONENT_IS_STARTED) {
+		XTmrCtr_Stop(InstancePtr, XTC_TIMER_1);
+	}
+
+	/* Configure timers modes to be used for PWM */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_0, XTC_TCSR_OFFSET);
+	CounterControlReg |=
+		(XTC_CSR_DOWN_COUNT_MASK | XTC_CSR_AUTO_RELOAD_MASK);
+	CounterControlReg &= (u32)~(XTC_CSR_CASC_MASK | XTC_CSR_EXT_GENERATE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_0,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_1, XTC_TCSR_OFFSET);
+	CounterControlReg |=
+		(XTC_CSR_DOWN_COUNT_MASK | XTC_CSR_AUTO_RELOAD_MASK);
+	CounterControlReg &= (u32)~(XTC_CSR_CASC_MASK | XTC_CSR_EXT_GENERATE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_1,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	/* Set period and high time for PWM */
+	SysClkPeriod = XTC_HZ_TO_NS(InstancePtr->Config.SysClockFreqHz);
+	if (PwmPeriod < PwmHighTime ||
+		PwmPeriod < (2 * SysClkPeriod) ||
+		PwmHighTime < (2 * SysClkPeriod)) {
+		return XST_INVALID_PARAM;
+	}
+
+	Period = XTC_ROUND_DIV(PwmPeriod, SysClkPeriod) - 2;
+	High = XTC_ROUND_DIV(PwmHighTime, SysClkPeriod) - 2;
+	if (Period > XTC_MAX_LOAD_VALUE) {
+		return XST_INVALID_PARAM;
+	}
+
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_0,
+						XTC_TLR_OFFSET, (u32)Period);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_1,
+						XTC_TLR_OFFSET, (u32)High);
+
+	/* Configure timers in generate mode */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_0, XTC_TCSR_OFFSET);
+	CounterControlReg &= (u32)~(XTC_CSR_CAPTURE_MODE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_0,
+					XTC_TCSR_OFFSET, CounterControlReg);
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_1, XTC_TCSR_OFFSET);
+	CounterControlReg &= (u32)~(XTC_CSR_CAPTURE_MODE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_1,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	return (u8)XTC_ROUND_DIV(High * 100, Period);
+}
+
+/*****************************************************************************/
+/**
+*
+* Enables the PWM output as per configurations set by XTmrCtr_PwmConfigure.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+*
+* @return	none.
+*
+* @note		none.
+*
+******************************************************************************/
+void XTmrCtr_PwmEnable(XTmrCtr *InstancePtr)
+{
+	u32 CounterControlReg;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* PWM already running */
+	if (InstancePtr->IsPwmEnabled) {
+		return;
+	}
+
+	/* Enable PWM, Generate Out */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_0, XTC_TCSR_OFFSET);
+	CounterControlReg |=
+			(XTC_CSR_ENABLE_PWM_MASK | XTC_CSR_EXT_GENERATE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_0,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_1, XTC_TCSR_OFFSET);
+	CounterControlReg |=
+			(XTC_CSR_ENABLE_PWM_MASK | XTC_CSR_EXT_GENERATE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_1,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	/* Reset Counters */
+	XTmrCtr_Reset(InstancePtr, XTC_TIMER_0);
+	XTmrCtr_Reset(InstancePtr, XTC_TIMER_1);
+
+	/* Enable all timers */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_0, XTC_TCSR_OFFSET);
+	CounterControlReg |= XTC_CSR_ENABLE_ALL_MASK;
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_0,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	InstancePtr->IsPwmEnabled = TRUE;
+}
+
+/*****************************************************************************/
+/**
+*
+* Disables the PWM output.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+*
+* @return	none.
+*
+* @note		Call to this function disables only the PWM output and do not
+*		alter any configuration. PWM output can again be enabled by
+*		calling XTmrCtr_PwmEnable without the need of re-configuration.
+*
+******************************************************************************/
+void XTmrCtr_PwmDisable(XTmrCtr *InstancePtr)
+{
+	u32 CounterControlReg;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/* PWM already disabled */
+	if (!InstancePtr->IsPwmEnabled) {
+		return;
+	}
+
+	/* Disable timers */
+	XTmrCtr_Stop(InstancePtr, XTC_TIMER_0);
+	XTmrCtr_Stop(InstancePtr, XTC_TIMER_1);
+
+	/* Reset Counters */
+	XTmrCtr_Reset(InstancePtr, XTC_TIMER_0);
+	XTmrCtr_Reset(InstancePtr, XTC_TIMER_1);
+
+	/* Disable PWM, Generate Out */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_0, XTC_TCSR_OFFSET);
+	CounterControlReg &=
+			(u32)~(XTC_CSR_ENABLE_PWM_MASK | XTC_CSR_EXT_GENERATE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_0,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					XTC_TIMER_1, XTC_TCSR_OFFSET);
+	CounterControlReg &=
+			(u32)~(XTC_CSR_ENABLE_PWM_MASK | XTC_CSR_EXT_GENERATE_MASK);
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, XTC_TIMER_1,
+					XTC_TCSR_OFFSET, CounterControlReg);
+
+	InstancePtr->IsPwmEnabled = FALSE;
+}
+
+/*****************************************************************************/
+/**
+* Default callback for the driver does nothing. It matches the signature of the
+* XTmrCtr_Handler type.
+*
+* @param	CallBackRef is a pointer to the callback's data.
+* @param	TmrCtrNumber is the ID of the timer counter which a user-defined
+*		callback would normally operate on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XTmrCtr_StubCallback(void *CallBackRef, u8 TmrCtrNumber)
+{
+	Xil_AssertVoid(CallBackRef != NULL);
+	Xil_AssertVoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr.h
@@ -0,0 +1,318 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr.h
+* @{
+* @details
+*
+* The Xilinx timer/counter component. This component supports the Xilinx
+* timer/counter. More detailed description of the driver operation can
+* be found in the xtmrctr.c file.
+*
+* The Xilinx timer/counter supports the following features:
+*   - Polled mode.
+*   - Interrupt driven mode
+*   - enabling and disabling specific timers
+*   - PWM operation
+*   - Cascade Operation (This is to be used for getting a 64 bit timer and this
+*     feature is present in the latest versions of the axi_timer IP)
+*
+* The timer counter operates in 2 primary modes, compare and capture. In
+* either mode, the timer counter may count up or down, with up being the
+* default.
+*
+* Compare mode is typically used for creating a single time period or multiple
+* repeating time periods in the auto reload mode, such as a periodic interrupt.
+* When started, the timer counter loads an initial value, referred to as the
+* compare value, into the timer counter and starts counting down or up. The
+* timer counter expires when it rolls over/under depending upon the mode of
+* counting. An external compare output signal may be configured such that a
+* pulse is generated with this signal when it hits the compare value.
+*
+* Capture mode is typically used for measuring the time period between
+* external events. This mode uses an external capture input signal to cause
+* the value of the timer counter to be captured. When started, the timer
+* counter loads an initial value, referred to as the compare value,
+
+* The timer can be configured to either cause an interrupt when the count
+* reaches the compare value in compare mode or latch the current count
+* value in the capture register when an external input is asserted
+* in capture mode. The external capture input can be enabled/disabled using the
+* XTmrCtr_SetOptions function. While in compare mode, it is also possible to
+* drive an external output when the compare value is reached in the count
+* register The external compare output can be enabled/disabled using the
+* XTmrCtr_SetOptions function.
+*
+* <b>Interrupts</b>
+*
+* It is the responsibility of the application to connect the interrupt
+* handler of the timer/counter to the interrupt source. The interrupt
+* handler function, XTmrCtr_InterruptHandler, is visible such that the user
+* can connect it to the interrupt source. Note that this interrupt handler
+* does not provide interrupt context save and restore processing, the user
+* must perform this processing.
+*
+* The driver services interrupts and passes timeouts to the upper layer
+* software through callback functions. The upper layer software must register
+* its callback functions during initialization. The driver requires callback
+* functions for timers.
+*
+* @note
+* The default settings for the timers are:
+*   - Interrupt generation disabled
+*   - Count up mode
+*   - Compare mode
+*   - Hold counter (will not reload the timer)
+*   - External compare output disabled
+*   - External capture input disabled
+*   - Pulse width modulation disabled
+*   - Timer disabled, waits for Start function to be called
+* <br><br>
+* A timer counter device may contain multiple timer counters. The symbol
+* XTC_DEVICE_TIMER_COUNT defines the number of timer counters in the device.
+* The device currently contains 2 timer counters.
+* <br><br>
+* This driver is intended to be RTOS and processor independent. It works with
+* physical addresses only. Any needs for dynamic memory management, threads
+* or thread mutual exclusion, virtual memory, or cache control must be
+* satisfied by the layer above this driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00a ecm  08/16/01 First release
+* 1.00b jhl  02/21/02 Repartitioned the driver for smaller files
+* 1.10b mta  03/21/07 Updated to new coding style.
+* 1.11a sdm  08/22/08 Removed support for static interrupt handlers from the MDD
+*		      file
+* 2.00a ktn  10/30/09 Updated to use HAL API's. _m is removed from all the macro
+*		      definitions.
+* 2.01a ktn  07/12/10 Renamed the macro XTimerCtr_ReadReg as XTmrCtr_ReadReg
+*		      for naming consistency (CR 559142).
+* 2.02a sdm  09/28/10 Updated the driver tcl to generate the xparameters
+*		      for the timer clock frequency (CR 572679).
+* 2.03a rvo  11/30/10 Added check to see if interrupt is enabled before further
+*		      processing for CR 584557.
+* 2.04a sdm  07/12/11 Added support for cascade mode operation.
+* 		      The cascade mode of operation is present in the latest
+*		      versions of the axi_timer IP. Please check the HW
+*		      Datasheet to see whether this feature is present in the
+*		      version of the IP that you are using.
+* 2.05a adk  15/05/13 Fixed the CR:693066
+*		      Added the IsStartedTmrCtr0/IsStartedTmrCtr1 members to the
+*		      XTmrCtr instance structure.
+*		      The IsStartedTmrCtrX will be assigned XIL_COMPONENT_IS_STARTED in
+*		      the XTmrCtr_Start function.
+*		      The IsStartedTmrCtrX will be cleared in the XTmrCtr_Stop function.
+*		      There will be no Initialization done in the
+*		      XTmrCtr_Initialize if both the timers have already started and
+*		      the XST_DEVICE_IS_STARTED Status is returned.
+*		      Removed the logic in the XTmrCtr_Initialize function
+*		      which was checking the Register Value to know whether
+*		      a timer has started or not.
+* 3.0   adk  19/12/13 Updated as per the New Tcl API's
+* 4.0   als  09/30/15 Updated initialization API.
+* 4.1   sk   11/10/15 Used UINTPTR instead of u32 for Baseaddress CR# 867425.
+*                     Changed the prototype of XTmrCtr_CfgInitialize API.
+* 4.2   nsk  15/09/16 Updated tcl, to get correct device id for canonical defines,
+*                     when there exist more than one timer perepheral
+*       ms   01/23/17 Added xil_printf statement in main function for all
+*                     examples to ensure that "Successfully ran" and "Failed"
+*                     strings are available in all examples. This is a fix
+*                     for CR-965028.
+*       ms   03/17/17 Added readme.txt file in examples folder for doxygen
+*                     generation.
+* 4.4   ms   04/18/17 Modified tcl file to add suffix U for all macros
+*                     definitions of tmrctr in xparameters.h
+* 4.5   cjp  03/22/18 Added APIs to support PWM feature. XTmrCtr_PwmConfigure
+*                     is used to configure PWM to operate for specific period
+*                     and high time. XTmrCtr_PwmEnable and XTmrCtr_PwmDisable
+*                     are used to enable/disable the PWM output.
+* 4.6   mus  03/13/19 tmrctr_tapp tcl is updated to support scenario where
+*                     AXI TIMER is interrupting ARM processor through more
+*                     than one interrupt pin. Fix for CR#1024699
+* 4.7   mus  08/31/20 Updated makefile to support parallel make and
+*                     incremental builds. It would help to reduce
+*                     compilation time.
+* 4.8   dp   02/12/21 Fix compilation errors that arise when -Werror=conversion
+*                     is enabled in compilation flags.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XTMRCTR_H		/* prevent circular inclusions */
+#define XTMRCTR_H		/* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_types.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xtmrctr_l.h"
+
+/************************** Constant Definitions *****************************/
+
+/**
+ * @name Configuration options
+ * These options are used in XTmrCtr_SetOptions() and XTmrCtr_GetOptions()
+ * @{
+ */
+/**
+ * Used to configure the timer counter device.
+ * <pre>
+ * XTC_CASCADE_MODE_OPTION	Enables the Cascade Mode only valid for TCSRO.
+ * XTC_ENABLE_ALL_OPTION	Enables all timer counters at once.
+ * XTC_DOWN_COUNT_OPTION	Configures the timer counter to count down from
+ *				start value, the default is to count up.
+ * XTC_CAPTURE_MODE_OPTION	Configures the timer to capture the timer
+ *				counter value when the external capture line is
+ *				asserted. The default mode is compare mode.
+ * XTC_INT_MODE_OPTION		Enables the timer counter interrupt output.
+ * XTC_AUTO_RELOAD_OPTION	In compare mode, configures the timer counter to
+ *				reload from the compare value. The default mode
+ *				causes the timer counter to hold when the
+ *				compare value is hit.
+ *				In capture mode, configures the timer counter to
+ *				not hold the previous capture value if a new
+ *				event occurs. The default mode cause the timer
+ *				counter to hold the capture value until
+ *				recognized.
+ * XTC_EXT_COMPARE_OPTION	Enables the external compare output signal.
+ * </pre>
+ */
+#define XTC_CASCADE_MODE_OPTION		0x00000080UL
+#define XTC_ENABLE_ALL_OPTION		0x00000040UL
+#define XTC_DOWN_COUNT_OPTION		0x00000020UL
+#define XTC_CAPTURE_MODE_OPTION		0x00000010UL
+#define XTC_INT_MODE_OPTION		0x00000008UL
+#define XTC_AUTO_RELOAD_OPTION		0x00000004UL
+#define XTC_EXT_COMPARE_OPTION		0x00000002UL
+/*@}*/
+
+/* Round division  */
+#define XTC_ROUND_DIV(a, b)		((a + (b / 2)) / b)
+
+/* Convert clock frequency in hertz to period in nano seconds */
+#define XTC_HZ_TO_NS(Hz)		XTC_ROUND_DIV(1000000000, Hz)
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * This typedef contains configuration information for the device.
+ */
+typedef struct {
+	u16 DeviceId;		/**< Unique ID  of device */
+	UINTPTR BaseAddress;	/**< Register base address */
+	u32 SysClockFreqHz;	/**< The AXI bus clock frequency */
+} XTmrCtr_Config;
+
+/**
+ * Signature for the callback function.
+ *
+ * @param	CallBackRef is a callback reference passed in by the upper layer
+ *		when setting the callback functions, and passed back to the
+ *		upper layer when the callback is invoked. Its type is
+ *		 unimportant to the driver, so it is a void pointer.
+ * @param 	TmrCtrNumber is the number of the timer/counter within the
+ *		device. The device typically contains at least two
+ *		timer/counters. The timer number is a zero based number with a
+ *		range of 0 to (XTC_DEVICE_TIMER_COUNT - 1).
+ */
+typedef void (*XTmrCtr_Handler) (void *CallBackRef, u8 TmrCtrNumber);
+
+
+/**
+ * Timer/Counter statistics
+ */
+typedef struct {
+	u32 Interrupts;	 /**< The number of interrupts that have occurred */
+} XTmrCtrStats;
+
+/**
+ * The XTmrCtr driver instance data. The user is required to allocate a
+ * variable of this type for every timer/counter device in the system. A
+ * pointer to a variable of this type is then passed to the driver API
+ * functions.
+ */
+typedef struct {
+	XTmrCtr_Config Config;   /**< Core configuration. */
+	XTmrCtrStats Stats;	 /**< Component Statistics */
+	UINTPTR BaseAddress;	 /**< Base address of registers */
+	u32 IsReady;		 /**< Device is initialized and ready */
+	u32 IsStartedTmrCtr0;	 /**< Is Timer Counter 0 started */
+	u32 IsStartedTmrCtr1;	 /**< Is Timer Counter 1 started */
+	u32 IsPwmEnabled;        /**< Is PWM Enabled */
+
+	XTmrCtr_Handler Handler; /**< Callback function */
+	void *CallBackRef;	 /**< Callback reference for handler */
+} XTmrCtr;
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+/* Required functions, in file xtmrctr.c */
+void XTmrCtr_CfgInitialize(XTmrCtr *InstancePtr, XTmrCtr_Config *ConfigPtr,
+		UINTPTR EffectiveAddr);
+int XTmrCtr_InitHw(XTmrCtr *InstancePtr);
+int XTmrCtr_Initialize(XTmrCtr * InstancePtr, u16 DeviceId);
+void XTmrCtr_Start(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+void XTmrCtr_Stop(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+u32 XTmrCtr_GetValue(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+void XTmrCtr_SetResetValue(XTmrCtr * InstancePtr, u8 TmrCtrNumber,
+			   u32 ResetValue);
+u32 XTmrCtr_GetCaptureValue(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+int XTmrCtr_IsExpired(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+void XTmrCtr_Reset(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+u8 XTmrCtr_PwmConfigure(XTmrCtr *InstancePtr, u32 PwmPeriod, u32 PwmHighTime);
+void XTmrCtr_PwmEnable(XTmrCtr *InstancePtr);
+void XTmrCtr_PwmDisable(XTmrCtr *InstancePtr);
+
+/* Lookup configuration in xtmrctr_sinit.c */
+XTmrCtr_Config *XTmrCtr_LookupConfig(u16 DeviceId);
+
+/* Functions for options, in file xtmrctr_options.c */
+void XTmrCtr_SetOptions(XTmrCtr * InstancePtr, u8 TmrCtrNumber, u32 Options);
+u32 XTmrCtr_GetOptions(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+
+/* Functions for statistics, in file xtmrctr_stats.c */
+void XTmrCtr_GetStats(XTmrCtr * InstancePtr, XTmrCtrStats * StatsPtr);
+void XTmrCtr_ClearStats(XTmrCtr * InstancePtr);
+
+/* Functions for self-test, in file xtmrctr_selftest.c */
+int XTmrCtr_SelfTest(XTmrCtr * InstancePtr, u8 TmrCtrNumber);
+
+/* Functions for interrupts, in file xtmrctr_intr.c */
+void XTmrCtr_SetHandler(XTmrCtr * InstancePtr, XTmrCtr_Handler FuncPtr,
+			void *CallBackRef);
+void XTmrCtr_InterruptHandler(void *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_i.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_i.h
@@ -0,0 +1,63 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr_i.h
+* @{
+*
+* This file contains data which is shared between files internal to the
+* XTmrCtr component. It is intended for internal use only.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00b jhl  02/06/02 First release
+* 1.10b mta  03/21/07 Updated to new coding style
+* 2.00a ktn  10/30/09 _m is removed from all the macro definitions.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XTMRCTR_I_H		/* prevent circular inclusions */
+#define XTMRCTR_I_H		/* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_types.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+extern u8 XTmrCtr_Offsets[];
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_intr.c
@@ -0,0 +1,219 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr_intr.c
+* @{
+*
+* Contains interrupt-related functions for the XTmrCtr component.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00b jhl  02/06/02 First release
+* 1.10b mta  03/21/07 Updated to new coding style
+* 2.00a ktn  10/30/09 Updated to use HAL API's. _m is removed from all the macro
+*		      definitions.
+* 2.03a rvo  11/30/10 Added check to see if interrupt is enabled before further
+*		      processing for CR 584557.
+* 4.8   dp   02/12/21 Fix compilation errors that arise when -Werror=conversion
+*                     is enabled in compilation flags.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xtmrctr.h"
+#include "xil_printf.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+
+/*****************************************************************************/
+/**
+*
+* Sets the timer callback function, which the driver calls when the specified
+* timer times out.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance .
+* @param	CallBackRef is the upper layer callback reference passed back
+*		when the callback function is invoked.
+* @param	FuncPtr is the pointer to the callback function.
+*
+* @return	None.
+*
+* @note
+*
+* The handler is called within interrupt context so the function that is
+* called should either be short or pass the more extensive processing off
+* to another task to allow the interrupt to return and normal processing
+* to continue.
+*
+******************************************************************************/
+void XTmrCtr_SetHandler(XTmrCtr * InstancePtr, XTmrCtr_Handler FuncPtr,
+			void *CallBackRef)
+{
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(FuncPtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	InstancePtr->Handler = FuncPtr;
+	InstancePtr->CallBackRef = CallBackRef;
+}
+
+/*****************************************************************************/
+/**
+*
+* Interrupt Service Routine (ISR) for the driver.  This function only performs
+* processing for the device and does not save and restore the interrupt context.
+*
+* @param	InstancePtr contains a pointer to the timer/counter instance for
+*		the interrupt.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XTmrCtr_InterruptHandler(void *InstancePtr)
+{
+	XTmrCtr *TmrCtrPtr = NULL;
+	u8 TmrCtrNumber;
+	u32 ControlStatusReg;
+
+	/*
+	 * Verify that each of the inputs are valid.
+	 */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	/*
+	 * Convert the non-typed pointer to an timer/counter instance pointer
+	 * such that there is access to the timer/counter
+	 */
+	TmrCtrPtr = (XTmrCtr *) InstancePtr;
+
+	/*
+	 * Loop thru each timer counter in the device and call the callback
+	 * function for each timer which has caused an interrupt
+	 */
+	for (TmrCtrNumber = 0;
+		TmrCtrNumber < XTC_DEVICE_TIMER_COUNT; TmrCtrNumber++) {
+
+		ControlStatusReg = XTmrCtr_ReadReg(TmrCtrPtr->BaseAddress,
+						   TmrCtrNumber,
+						   XTC_TCSR_OFFSET);
+		/*
+		 * Linux - 	Do not check if interrupt is enabled as top half will 
+					mask the interrupt
+		 */
+//		if (ControlStatusReg & XTC_CSR_ENABLE_INT_MASK) {
+
+			/*
+			 * Check if timer expired and interrupt occured
+			 */
+			if (ControlStatusReg & XTC_CSR_INT_OCCURED_MASK) {
+				/*
+				 * Increment statistics for the number of
+				 * interrupts and call the callback to handle
+				 * any application specific processing
+				 */
+				TmrCtrPtr->Stats.Interrupts++;
+				TmrCtrPtr->Handler(TmrCtrPtr->CallBackRef,
+						   TmrCtrNumber);
+				/*
+				 * Read the new Control/Status Register content.
+				 */
+				ControlStatusReg =
+					XTmrCtr_ReadReg(TmrCtrPtr->BaseAddress,
+								TmrCtrNumber,
+								XTC_TCSR_OFFSET);
+				/*
+				 * If in compare mode and a single shot rather
+				 * than auto reload mode then disable the timer
+				 * and reset it such so that the interrupt can
+				 * be acknowledged, this should be only temporary
+				 * till the hardware is fixed
+				 */
+				if (((ControlStatusReg &
+					XTC_CSR_AUTO_RELOAD_MASK) == 0) &&
+					((ControlStatusReg &
+					  XTC_CSR_CAPTURE_MODE_MASK)== 0)) {
+						/*
+						 * Disable the timer counter and
+						 * reset it such that the timer
+						 * counter is loaded with the
+						 * reset value allowing the
+						 * interrupt to be acknowledged
+						 */
+						ControlStatusReg &=
+							(u32)~XTC_CSR_ENABLE_TMR_MASK;
+
+						XTmrCtr_WriteReg(
+							TmrCtrPtr->BaseAddress,
+							TmrCtrNumber,
+							XTC_TCSR_OFFSET,
+							ControlStatusReg |
+							XTC_CSR_LOAD_MASK);
+
+						/*
+						 * Clear the reset condition,
+						 * the reset bit must be
+						 * manually cleared by a 2nd write
+						 * to the register
+						 */
+						XTmrCtr_WriteReg(
+							TmrCtrPtr->BaseAddress,
+							TmrCtrNumber,
+							XTC_TCSR_OFFSET,
+							ControlStatusReg);
+				}
+
+				/*
+				 * Acknowledge the interrupt by clearing the
+				 * interrupt bit in the timer control status
+				 * register, this is done after calling the
+				 * handler so the application could call
+				 * IsExpired, the interrupt is cleared by
+				 * writing a 1 to the interrupt bit of the
+				 * register without changing any of the other
+				 * bits
+				 */
+				XTmrCtr_WriteReg(TmrCtrPtr->BaseAddress,
+						 TmrCtrNumber,
+						 XTC_TCSR_OFFSET,
+						 ControlStatusReg |
+						 XTC_CSR_INT_OCCURED_MASK);
+			}
+//		}
+	} //for
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_l.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_l.c
@@ -0,0 +1,62 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr_l.c
+* @{
+*
+* This file contains low-level driver functions that can be used to access the
+* device.  The user should refer to the hardware device specification for more
+* details of the device operation.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00b jhl  04/24/02 First release
+* 1.10b mta  03/21/07 Updated to new coding style
+* 2.00a ktn  10/30/09 Updated to use HAL API's
+* </pre>
+*
+******************************************************************************/
+
+
+/***************************** Include Files *********************************/
+
+#include "xtmrctr_l.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+/* The following table contains the offset from the base address of a timer
+ * counter device for each timer counter.  A single device may contain multiple
+ * timer counters and the functions specify which one to operate on.
+ */
+u8 XTmrCtr_Offsets[] = { 0, XTC_TIMER_COUNTER_OFFSET };
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_l.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_l.h
@@ -0,0 +1,424 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr_l.h
+* @{
+*
+* This header file contains identifiers and low-level driver functions (or
+* macros) that can be used to access the device.  The user should refer to the
+* hardware device specification for more details of the device operation.
+* High-level driver functions are defined in xtmrctr.h.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00b jhl  04/24/02 First release
+* 1.10b mta  03/21/07 Updated to new coding style
+* 2.00a ktn  10/30/09 Updated to use HAL API's. _m is removed from all the macro
+*		      definitions.
+* 2.01a ktn  07/12/10 Renamed the macro XTimerCtr_ReadReg as XTmrCtr_ReadReg
+*		      for naming consistency (CR 559142).
+* 2.04a sdm  07/12/11 Added the CASC mode bit in the TCSRO register for the
+*		      cascade mode operation.
+*		      The cascade mode of operation is present in the latest
+*		      versions of the axi_timer IP. Please check the HW
+*		      Datasheet to see whether this feature is present in the
+*		      version of the IP that you are using.
+* 4.4   mus  07/21/17 Updated XTmrCtr_DisableIntr macro to not to clear
+*             T0INT flag
+* 4.5   cjp  03/22/18 Added macros for timer/counter instance number and max
+*                     load value.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XTMRCTR_L_H		/* prevent circular inclusions */
+#define XTMRCTR_L_H		/* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_types.h"
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+
+/**
+ * Defines the number of timer counters within a single hardware device. This
+ * number is not currently parameterized in the hardware but may be in the
+ * future.
+ */
+#define XTC_DEVICE_TIMER_COUNT		2
+
+/* Each timer counter consumes 16 bytes of address space */
+
+#define XTC_TIMER_COUNTER_OFFSET	16
+
+/* Timer counter instance number used for PWM */
+#define XTC_TIMER_0			0
+#define XTC_TIMER_1			1
+
+/* Max supported load value for timer/counter */
+#define XTC_MAX_LOAD_VALUE		0xFFFFFFFF
+
+/** @name Register Offset Definitions
+ * Register offsets within a timer counter, there are multiple
+ * timer counters within a single device
+ * @{
+ */
+
+#define XTC_TCSR_OFFSET		0	/**< Control/Status register */
+#define XTC_TLR_OFFSET		4	/**< Load register */
+#define XTC_TCR_OFFSET		8	/**< Timer counter register */
+
+/* @} */
+
+/** @name Control Status Register Bit Definitions
+ * Control Status Register bit masks
+ * Used to configure the timer counter device.
+ * @{
+ */
+
+#define XTC_CSR_CASC_MASK		0x00000800 /**< Cascade Mode */
+#define XTC_CSR_ENABLE_ALL_MASK		0x00000400 /**< Enables all timer
+							counters */
+#define XTC_CSR_ENABLE_PWM_MASK		0x00000200 /**< Enables the Pulse Width
+							Modulation */
+#define XTC_CSR_INT_OCCURED_MASK	0x00000100 /**< If bit is set, an
+							interrupt has occured.
+							If set and '1' is
+							written to this bit
+							position, bit is
+							cleared. */
+#define XTC_CSR_ENABLE_TMR_MASK		0x00000080 /**< Enables only the
+							specific timer */
+#define XTC_CSR_ENABLE_INT_MASK		0x00000040 /**< Enables the interrupt
+							output. */
+#define XTC_CSR_LOAD_MASK		0x00000020 /**< Loads the timer using
+							the load value provided
+							earlier in the Load
+							Register,
+							XTC_TLR_OFFSET. */
+#define XTC_CSR_AUTO_RELOAD_MASK	0x00000010 /**< In compare mode,
+							configures
+							the timer counter to
+							reload  from the
+							Load Register. The
+							default  mode
+							causes the timer counter
+							to hold when the compare
+							value is hit. In capture
+							mode, configures  the
+							timer counter to not
+							hold the previous
+							capture value if a new
+							event occurs. The
+							default mode cause the
+							timer counter to hold
+							the capture value until
+							recognized. */
+#define XTC_CSR_EXT_CAPTURE_MASK	0x00000008 /**< Enables the
+							external input
+							to the timer counter. */
+#define XTC_CSR_EXT_GENERATE_MASK	0x00000004 /**< Enables the
+							external generate output
+							for the timer. */
+#define XTC_CSR_DOWN_COUNT_MASK		0x00000002 /**< Configures the timer
+							counter to count down
+							from start value, the
+							default is to count
+							up.*/
+#define XTC_CSR_CAPTURE_MODE_MASK	0x00000001 /**< Enables the timer to
+							capture the timer
+							counter value when the
+							external capture line is
+							asserted. The default
+							mode is compare mode.*/
+/* @} */
+
+/**************************** Type Definitions *******************************/
+
+extern u8 XTmrCtr_Offsets[];
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+* Read one of the timer counter registers.
+*
+* @param	BaseAddress contains the base address of the timer counter
+*		device.
+* @param	TmrCtrNumber contains the specific timer counter within the
+*		device, a zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+* @param	RegOffset contains the offset from the 1st register of the timer
+*		counter to select the specific register of the timer counter.
+*
+* @return	The value read from the register, a 32 bit value.
+*
+* @note		C-Style signature:
+* 		u32 XTmrCtr_ReadReg(u32 BaseAddress, u8 TimerNumber,
+					unsigned RegOffset);
+******************************************************************************/
+#define XTmrCtr_ReadReg(BaseAddress, TmrCtrNumber, RegOffset)	\
+	Xil_In32((BaseAddress) + XTmrCtr_Offsets[(TmrCtrNumber)] + \
+			(RegOffset))
+
+#ifndef XTimerCtr_ReadReg
+#define XTimerCtr_ReadReg XTmrCtr_ReadReg
+#endif
+
+/*****************************************************************************/
+/**
+* Write a specified value to a register of a timer counter.
+*
+* @param	BaseAddress is the base address of the timer counter device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+* @param	RegOffset contain the offset from the 1st register of the timer
+*		counter to select the specific register of the timer counter.
+* @param	ValueToWrite is the 32 bit value to be written to the register.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_WriteReg(u32 BaseAddress, u8 TimerNumber,
+*					unsigned RegOffset, u32 ValueToWrite);
+******************************************************************************/
+#define XTmrCtr_WriteReg(BaseAddress, TmrCtrNumber, RegOffset, ValueToWrite)\
+	Xil_Out32(((BaseAddress) + XTmrCtr_Offsets[(TmrCtrNumber)] +	\
+			   (RegOffset)), (ValueToWrite))
+
+/****************************************************************************/
+/**
+*
+* Set the Control Status Register of a timer counter to the specified value.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+* @param	RegisterValue is the 32 bit value to be written to the register.
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_SetControlStatusReg(u32 BaseAddress,
+*					u8 TmrCtrNumber,u32 RegisterValue);
+*****************************************************************************/
+#define XTmrCtr_SetControlStatusReg(BaseAddress, TmrCtrNumber, RegisterValue)\
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET,     \
+					   (RegisterValue))
+
+/****************************************************************************/
+/**
+*
+* Get the Control Status Register of a timer counter.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device,
+*		a zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	The value read from the register, a 32 bit value.
+*
+* @note		C-Style signature:
+* 		u32 XTmrCtr_GetControlStatusReg(u32 BaseAddress,
+*						u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_GetControlStatusReg(BaseAddress, TmrCtrNumber)		\
+	XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET)
+
+/****************************************************************************/
+/**
+*
+* Get the Timer Counter Register of a timer counter.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device,
+*		a zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	The value read from the register, a 32 bit value.
+*
+* @note		C-Style signature:
+* 		u32 XTmrCtr_GetTimerCounterReg(u32 BaseAddress,
+*						u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_GetTimerCounterReg(BaseAddress, TmrCtrNumber)		  \
+	XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber), XTC_TCR_OFFSET) \
+
+/****************************************************************************/
+/**
+*
+* Set the Load Register of a timer counter to the specified value.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+* @param	RegisterValue is the 32 bit value to be written to the register.
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_SetLoadReg(u32 BaseAddress, u8 TmrCtrNumber,
+*						  u32 RegisterValue);
+*****************************************************************************/
+#define XTmrCtr_SetLoadReg(BaseAddress, TmrCtrNumber, RegisterValue)	 \
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TLR_OFFSET, \
+					   (RegisterValue))
+
+/****************************************************************************/
+/**
+*
+* Get the Load Register of a timer counter.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	The value read from the register, a 32 bit value.
+*
+* @note		C-Style signature:
+* 		u32 XTmrCtr_GetLoadReg(u32 BaseAddress, u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_GetLoadReg(BaseAddress, TmrCtrNumber)	\
+XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber), XTC_TLR_OFFSET)
+
+/****************************************************************************/
+/**
+*
+* Enable a timer counter such that it starts running.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_Enable(u32 BaseAddress, u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_Enable(BaseAddress, TmrCtrNumber)			    \
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET,   \
+			(XTmrCtr_ReadReg((BaseAddress), ( TmrCtrNumber), \
+			XTC_TCSR_OFFSET) | XTC_CSR_ENABLE_TMR_MASK))
+
+/****************************************************************************/
+/**
+*
+* Disable a timer counter such that it stops running.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device,
+*		a zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_Disable(u32 BaseAddress, u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_Disable(BaseAddress, TmrCtrNumber)			  \
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET, \
+			(XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber),\
+			XTC_TCSR_OFFSET) & ~ XTC_CSR_ENABLE_TMR_MASK))
+
+/****************************************************************************/
+/**
+*
+* Enable the interrupt for a timer counter.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_EnableIntr(u32 BaseAddress, u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_EnableIntr(BaseAddress, TmrCtrNumber)			    \
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET,   \
+			(XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber),  \
+			XTC_TCSR_OFFSET) | XTC_CSR_ENABLE_INT_MASK))
+
+/****************************************************************************/
+/**
+*
+* Disable the interrupt for a timer counter. 
+* (Linux - do not clear interrupt status bit TxINT)
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_DisableIntr(u32 BaseAddress, u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_DisableIntr(BaseAddress, TmrCtrNumber)			   \
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET,  \
+	(XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber),		   \
+		XTC_TCSR_OFFSET) & ~(XTC_CSR_ENABLE_INT_MASK|XTC_CSR_INT_OCCURED_MASK)))
+
+/****************************************************************************/
+/**
+*
+* Cause the timer counter to load it's Timer Counter Register with the value
+* in the Load Register.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		   zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return	None.
+*
+* @note		C-Style signature:
+* 		void XTmrCtr_LoadTimerCounterReg(u32 BaseAddress,
+					u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_LoadTimerCounterReg(BaseAddress, TmrCtrNumber)		  \
+	XTmrCtr_WriteReg((BaseAddress), (TmrCtrNumber), XTC_TCSR_OFFSET, \
+			(XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber),\
+			XTC_TCSR_OFFSET) | XTC_CSR_LOAD_MASK))
+
+/****************************************************************************/
+/**
+*
+* Determine if a timer counter event has occurred.  Events are defined to be
+* when a capture has occurred or the counter has roller over.
+*
+* @param	BaseAddress is the base address of the device.
+* @param	TmrCtrNumber is the specific timer counter within the device, a
+*		zero based number, 0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @note		C-Style signature:
+* 		int XTmrCtr_HasEventOccurred(u32 BaseAddress, u8 TmrCtrNumber);
+*****************************************************************************/
+#define XTmrCtr_HasEventOccurred(BaseAddress, TmrCtrNumber)		\
+		((XTmrCtr_ReadReg((BaseAddress), (TmrCtrNumber),	\
+		XTC_TCSR_OFFSET) & XTC_CSR_INT_OCCURED_MASK) ==		\
+		XTC_CSR_INT_OCCURED_MASK)
+
+/************************** Function Prototypes ******************************/
+/************************** Variable Definitions *****************************/
+#ifdef __cplusplus
+}
+#endif
+#endif /* end of protection macro */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_options.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_options.c
@@ -0,0 +1,200 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr_options.c
+* @{
+*
+* Contains configuration options functions for the XTmrCtr component.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00b jhl  02/06/02 First release
+* 1.10b mta  03/21/07 Updated to new coding style
+* 2.00a ktn  10/30/09 Updated to use HAL API's. _m is removed from all the macro
+*		      definitions.
+* 2.04a sdm  07/12/11 Added support for the cascade mode operation.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xtmrctr.h"
+#include "xtmrctr_i.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+/*
+ * The following data type maps an option to a register mask such that getting
+ * and setting the options may be table driven.
+ */
+typedef struct {
+	u32 Option;
+	u32 Mask;
+} Mapping;
+
+/*
+ * Create the table which contains options which are to be processed to get/set
+ * the options. These options are table driven to allow easy maintenance and
+ * expansion of the options.
+ */
+static Mapping OptionsTable[] = {
+	{XTC_CASCADE_MODE_OPTION, XTC_CSR_CASC_MASK},
+	{XTC_ENABLE_ALL_OPTION, XTC_CSR_ENABLE_ALL_MASK},
+	{XTC_DOWN_COUNT_OPTION, XTC_CSR_DOWN_COUNT_MASK},
+	{XTC_CAPTURE_MODE_OPTION, XTC_CSR_CAPTURE_MODE_MASK |
+	 XTC_CSR_EXT_CAPTURE_MASK},
+	{XTC_INT_MODE_OPTION, XTC_CSR_ENABLE_INT_MASK},
+	{XTC_AUTO_RELOAD_OPTION, XTC_CSR_AUTO_RELOAD_MASK},
+	{XTC_EXT_COMPARE_OPTION, XTC_CSR_EXT_GENERATE_MASK}
+};
+
+/* Create a constant for the number of entries in the table */
+
+#define XTC_NUM_OPTIONS   (sizeof(OptionsTable) / sizeof(Mapping))
+
+/*****************************************************************************/
+/**
+*
+* Enables the specified options for the specified timer counter. This function
+* sets the options without regard to the current options of the driver. To
+* prevent a loss of the current options, the user should call
+* XTmrCtr_GetOptions() prior to this function and modify the retrieved options
+* to pass into this function to prevent loss of the current options.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on.
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+* @param	Options contains the desired options to be set or cleared.
+*		Setting the option to '1' enables the option, clearing the to
+*		'0' disables the option. The options are bit masks such that
+*		multiple options may be set or cleared. The options are
+*		described in xtmrctr.h.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XTmrCtr_SetOptions(XTmrCtr * InstancePtr, u8 TmrCtrNumber, u32 Options)
+{
+	u32 CounterControlReg = 0;
+	u32 Index;
+
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/*
+	 * Loop through the Options table, turning the enable on or off
+	 * depending on whether the bit is set in the incoming Options flag.
+	 */
+
+	for (Index = 0; Index < XTC_NUM_OPTIONS; Index++) {
+		if (Options & OptionsTable[Index].Option) {
+
+			/*
+			 * Turn the option on
+			 */
+			CounterControlReg |= OptionsTable[Index].Mask;
+		}
+		else {
+			/*
+			 * Turn the option off
+			 */
+			CounterControlReg &= ~OptionsTable[Index].Mask;
+		}
+	}
+
+	/*
+	 * Write out the updated value to the actual register
+	 */
+	XTmrCtr_WriteReg(InstancePtr->BaseAddress, TmrCtrNumber,
+			  XTC_TCSR_OFFSET, CounterControlReg);
+}
+
+/*****************************************************************************/
+/**
+*
+* Get the options for the specified timer counter.
+*
+* @param	InstancePtr is a pointer to the XTmrCtr instance.
+* @param	TmrCtrNumber is the timer counter of the device to operate on
+*		Each device may contain multiple timer counters. The timer
+*		number is a zero based number with a range of
+*		0 - (XTC_DEVICE_TIMER_COUNT - 1).
+*
+* @return
+*
+* The currently set options. An option which is set to a '1' is enabled and
+* set to a '0' is disabled. The options are bit masks such that multiple
+* options may be set or cleared. The options are described in xtmrctr.h.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XTmrCtr_GetOptions(XTmrCtr * InstancePtr, u8 TmrCtrNumber)
+{
+
+	u32 Options = 0;
+	u32 CounterControlReg;
+	u32 Index;
+
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(TmrCtrNumber < XTC_DEVICE_TIMER_COUNT);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/*
+	 * Read the current contents of the control status register to allow
+	 * the current options to be determined
+	 */
+	CounterControlReg = XTmrCtr_ReadReg(InstancePtr->BaseAddress,
+					       TmrCtrNumber, XTC_TCSR_OFFSET);
+	/*
+	 * Loop through the Options table, turning the enable on or off
+	 * depending on whether the bit is set in the current register settings.
+	 */
+	for (Index = 0; Index < XTC_NUM_OPTIONS; Index++) {
+		if (CounterControlReg & OptionsTable[Index].Mask) {
+			Options |= OptionsTable[Index].Option;	/* turn it on */
+		}
+		else {
+			Options &= ~OptionsTable[Index].Option;	/* turn it off */
+		}
+	}
+
+	return Options;
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xtmrctr_sinit.c
@@ -0,0 +1,86 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xtmrctr_sinit.c
+* @{
+*
+* This file contains static initialization methods for the XTmrCtr driver.
+*
+* @note	None.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 4.0   als  09/30/15 Creation of this file. Moved LookupConfig from xtmrctr.c.
+* 4.4	mn   07/31/17 Resolve Compilation warning
+* </pre>
+*
+******************************************************************************/
+
+/******************************* Include Files *******************************/
+
+
+#include "xtmrctr.h"
+
+/************************** Constant Definitions *****************************/
+
+#ifndef XPAR_XTMRCTR_NUM_INSTANCES
+#define XPAR_XTMRCTR_NUM_INSTANCES	0
+#endif
+
+/*************************** Variable Declarations ***************************/
+
+/* A table of configuration structures containing the configuration information
+ * for each timer core in the system. */
+extern XTmrCtr_Config XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES];
+
+/**************************** Function Definitions ***************************/
+
+/*****************************************************************************/
+/**
+* Looks up the device configuration based on the unique device ID. The table
+* TmrCtr_ConfigTable contains the configuration info for each device in the
+* system.
+*
+* @param	DeviceId is the unique device ID to search for in the config
+*		table.
+*
+* @return	A pointer to the configuration that matches the given device
+* 		ID, or NULL if no match is found.
+*
+* @note		None.
+*
+******************************************************************************/
+XTmrCtr_Config *XTmrCtr_LookupConfig(u16 DeviceId)
+{
+	XTmrCtr_Config *CfgPtr = NULL;
+	u16 Index;
+
+	for (Index = 0; Index < XPAR_XTMRCTR_NUM_INSTANCES; Index++) {
+		if (XTmrCtr_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XTmrCtr_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return CfgPtr;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic.c
@@ -0,0 +1,1385 @@
+/*******************************************************************************
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+*******************************************************************************/
+/**
+ *
+ * @file xhdmic.c
+ * @{
+ *
+ * Contains common utility functions that are typically used by hdmi-related
+ * drivers and applications.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   EB  21/12/17 Initial release.
+ * 1.1   EB  10/04/18 Fixed a bug in XV_HdmiC_ParseAudioInfoFrame
+ * 1.2   EB  18/06/19 Added FrlRateTable
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+#include "xv_hdmic.h"
+
+/************************** Constant Definitions ******************************/
+
+/*****************************************************************************/
+/**
+* This table contains the attributes for various standard resolutions.
+* Each entry is of the format:
+* 1) Resolution ID
+* 2) Video Identification Code.
+* 3) Width
+* 4) Height
+* 5) Frame rate
+* 6) Aspect Ratio
+*/
+const XHdmiC_VicTable VicTable[VICTABLE_SIZE] = {
+    {XVIDC_VM_640x480_60_P, 1, 640, 480, 60, 0},      /* Vic 1 */
+    {XVIDC_VM_720x480_60_P, 2, 720, 480, 60, 0},      /* Vic 2 */
+    {XVIDC_VM_720x480_60_P, 3, 720, 480, 60, 1},      /* Vic 3 */
+    {XVIDC_VM_1280x720_60_P, 4, 1280, 720, 60, 1},     /* Vic 4 */
+    {XVIDC_VM_1920x1080_60_I, 5, 1920, 540, 120, 1},    /* Vic 5 */
+    {XVIDC_VM_1440x480_60_I, 6, 1440, 240, 120, 0},     /* Vic 6 */
+    {XVIDC_VM_1440x480_60_I, 7, 1440, 240, 120, 1},     /* Vic 7 */
+    {XVIDC_VM_1440x240_60_P, 8, 1440, 240, 60, 0},     /* Vic 8 */
+    {XVIDC_VM_1440x240_60_P, 9, 1440, 240, 60, 1},     /* Vic 9 */
+    {XVIDC_VM_2880x480_60_I, 10, 2880, 240, 120, 0},    /* Vic 10 */
+    {XVIDC_VM_2880x480_60_I, 11, 2880, 240, 120, 1},    /* Vic 11 */
+    {XVIDC_VM_2880x240_60_P, 12, 2880, 240, 60, 0},    /* Vic 12 */
+    {XVIDC_VM_2880x240_60_P, 13, 2880, 240, 60, 1},    /* Vic 13 */
+    {XVIDC_VM_1440x480_60_P, 14, 1440, 480, 60, 0},    /* Vic 14 */
+    {XVIDC_VM_1440x480_60_P, 15, 1440, 480, 60, 1},    /* Vic 15 */
+    {XVIDC_VM_1920x1080_60_P, 16, 1920, 1080, 60, 1},   /* Vic 16 */
+    {XVIDC_VM_720x576_50_P, 17, 720, 576, 50, 0},     /* Vic 17 */
+    {XVIDC_VM_720x576_50_P, 18, 720, 576, 50, 1},     /* Vic 18 */
+    {XVIDC_VM_1280x720_50_P, 19, 1280, 720, 50, 1},    /* Vic 19 */
+    {XVIDC_VM_1920x1080_50_I, 20, 1920, 540, 100, 1},   /* Vic 20 */
+    {XVIDC_VM_1440x576_50_I, 21, 1440, 288, 100, 0},    /* Vic 21 */
+    {XVIDC_VM_1440x576_50_I, 22, 1440, 288, 100, 1},    /* Vic 22 */
+    {XVIDC_VM_1440x288_50_P, 23, 1440, 288, 50, 0},    /* Vic 23 */
+    {XVIDC_VM_1440x288_50_P, 24, 1440, 288, 50, 1},    /* Vic 24 */
+    {XVIDC_VM_2880x576_50_I, 25, 2880, 288, 100, 0},    /* Vic 25 */
+    {XVIDC_VM_2880x576_50_I, 26, 2880, 288, 100, 1},    /* Vic 26 */
+    {XVIDC_VM_2880x288_50_P, 27, 2880, 288, 50, 0},    /* Vic 27 */
+    {XVIDC_VM_2880x288_50_P, 28, 2880, 288, 50, 1},    /* Vic 28 */
+    {XVIDC_VM_1440x576_50_P, 29, 1440, 576, 50, 0},    /* Vic 29 */
+    {XVIDC_VM_1440x576_50_P, 30, 1440, 576, 50, 1},    /* Vic 30 */
+    {XVIDC_VM_1920x1080_50_P, 31, 1920, 1080, 50, 1},   /* Vic 31 */
+    {XVIDC_VM_1920x1080_24_P, 32, 1920, 1080, 24, 1},   /* Vic 32 */
+    {XVIDC_VM_1920x1080_25_P, 33, 1920, 1080, 25, 1},   /* Vic 33 */
+    {XVIDC_VM_1920x1080_30_P, 34, 1920, 1080, 30, 1},   /* Vic 34 */
+    {XVIDC_VM_2880x480_60_P, 35, 2880, 480, 60, 0},    /* Vic 35 */
+    {XVIDC_VM_2880x480_60_P, 36, 2880, 480, 60, 1},    /* Vic 36 */
+    {XVIDC_VM_2880x576_50_P, 37, 2880, 576, 50, 0},    /* Vic 37 */
+    {XVIDC_VM_2880x576_50_P, 38, 2880, 576, 50, 1},    /* Vic 38 */
+    {XVIDC_VM_1920x1080_100_I, 40, 1920, 540, 200, 1},  /* Vic 40 */
+    {XVIDC_VM_1280x720_100_P, 41, 1280, 720, 100, 1},   /* Vic 41 */
+    {XVIDC_VM_720x576_100_P, 42, 720, 576, 100, 0},    /* Vic 42 */
+    {XVIDC_VM_720x576_100_P, 43, 720, 576, 100, 1},    /* Vic 43 */
+    {XVIDC_VM_1440x576_100_I, 44, 1440, 288, 200, 0},   /* Vic 44 */
+    {XVIDC_VM_1440x576_100_I, 45, 1440, 288, 200, 1},   /* Vic 45 */
+    {XVIDC_VM_1920x1080_120_I, 46, 1920, 540, 240, 1},  /* Vic 46 */
+    {XVIDC_VM_1280x720_120_P, 47, 1280, 720, 120, 1},   /* Vic 47 */
+    {XVIDC_VM_720x480_120_P, 48, 720, 480, 120, 0},    /* Vic 48 */
+    {XVIDC_VM_720x480_120_P, 49, 720, 480, 120, 1},    /* Vic 49 */
+    {XVIDC_VM_1440x480_120_I, 50, 1440, 240, 240, 0},   /* Vic 50 */
+    {XVIDC_VM_1440x480_120_I, 51, 1440, 240, 240, 1},   /* Vic 51 */
+    {XVIDC_VM_720x576_200_P, 52, 720, 576, 200, 0},    /* Vic 52 */
+    {XVIDC_VM_720x576_200_P, 53, 720, 576, 200, 1},    /* Vic 53 */
+    {XVIDC_VM_1440x576_200_I, 54, 1440, 288, 400, 0},   /* Vic 54 */
+    {XVIDC_VM_1440x576_200_I, 55, 1440, 288, 400, 1},   /* Vic 55 */
+    {XVIDC_VM_720x480_240_P, 56, 720, 480, 240, 0},    /* Vic 56 */
+    {XVIDC_VM_720x480_240_P, 57, 720, 480, 240, 1},    /* Vic 57 */
+    {XVIDC_VM_1440x480_240_I, 58, 1440, 240, 480, 0},   /* Vic 58 */
+    {XVIDC_VM_1440x480_240_I, 59, 1440, 240, 480, 1},   /* Vic 59 */
+    {XVIDC_VM_1280x720_24_P, 60, 1280, 720, 24, 1},    /* Vic 60 */
+    {XVIDC_VM_1280x720_25_P, 61, 1280, 720, 25, 1},    /* Vic 61 */
+    {XVIDC_VM_1280x720_30_P, 62, 1280, 720, 30, 1},    /* Vic 62 */
+    {XVIDC_VM_1920x1080_120_P, 63, 1920, 1080, 120, 1},  /* Vic 63 */
+    {XVIDC_VM_1920x1080_100_P, 64, 1920, 1080, 100, 1},  /* Vic 64 */
+
+    /* 1280 x 720 */
+    {XVIDC_VM_1280x720_24_P, 65, 1280, 720, 24, 2},    /* Vic 65 */
+    {XVIDC_VM_1280x720_25_P, 66, 1280, 720, 25, 2},    /* Vic 66 */
+    {XVIDC_VM_1280x720_30_P, 67, 1280, 720, 30, 2},    /* Vic 67 */
+    {XVIDC_VM_1280x720_50_P, 68, 1280, 720, 50, 2},    /* Vic 68 */
+    {XVIDC_VM_1280x720_60_P, 69, 1280, 720, 60, 2},    /* Vic 69 */
+    {XVIDC_VM_1280x720_100_P, 70, 1280, 720, 100, 2},   /* Vic 70 */
+    {XVIDC_VM_1280x720_120_P, 71, 1280, 720, 120, 2},   /* Vic 71 */
+
+    /* 1680 x 720 */
+    {XVIDC_VM_1680x720_24_P, 79, 1680, 720, 24, 2},    /* Vic 79 */
+    {XVIDC_VM_1680x720_25_P, 80, 1680, 720, 25, 2},    /* Vic 80 */
+    {XVIDC_VM_1680x720_30_P, 81, 1680, 720, 30, 2},    /* Vic 81 */
+    {XVIDC_VM_1680x720_50_P, 82, 1680, 720, 50, 2},    /* Vic 82 */
+    {XVIDC_VM_1680x720_60_P, 83, 1680, 720, 60, 2},    /* Vic 83 */
+    {XVIDC_VM_1680x720_100_P, 84, 1680, 720, 100, 2},   /* Vic 84 */
+    {XVIDC_VM_1680x720_120_P, 85, 1680, 720, 120, 2},   /* Vic 85 */
+
+    /* 1920 x 1080 */
+    {XVIDC_VM_1920x1080_24_P, 72, 1920, 1080, 24, 2},   /* Vic 72 */
+    {XVIDC_VM_1920x1080_25_P, 73, 1920, 1080, 25, 2},   /* Vic 73 */
+    {XVIDC_VM_1920x1080_30_P, 74, 1920, 1080, 30, 2},   /* Vic 74 */
+    {XVIDC_VM_1920x1080_50_P, 75, 1920, 1080, 50, 2},   /* Vic 75 */
+    {XVIDC_VM_1920x1080_60_P, 76, 1920, 1080, 60, 2},   /* Vic 76 */
+    {XVIDC_VM_1920x1080_100_P, 77, 1920, 1080, 100, 2},  /* Vic 77 */
+    {XVIDC_VM_1920x1080_120_P, 78, 1920, 1080, 120, 2},  /* Vic 78 */
+
+    /* 2560 x 1080 */
+    {XVIDC_VM_2560x1080_24_P, 86, 2560, 1080, 24, 2},   /* Vic 86 */
+    {XVIDC_VM_2560x1080_25_P, 87, 2560, 1080, 25, 2},   /* Vic 87 */
+    {XVIDC_VM_2560x1080_30_P, 88, 2560, 1080, 30, 2},   /* Vic 88 */
+    {XVIDC_VM_2560x1080_50_P, 89, 2560, 1080, 50, 2},   /* Vic 89 */
+    {XVIDC_VM_2560x1080_60_P, 90, 2560, 1080, 60, 2},   /* Vic 90 */
+    {XVIDC_VM_2560x1080_100_P, 91, 2560, 1080, 100, 2},  /* Vic 91 */
+    {XVIDC_VM_2560x1080_120_P, 92, 2560, 1080, 120, 2},  /* Vic 92 */
+
+    /* 3840 x 2160 */
+    {XVIDC_VM_3840x2160_24_P, 93, 3840, 2160, 24, 1},   /* Vic 93  */
+    {XVIDC_VM_3840x2160_25_P, 94, 3840, 2160, 25, 1},   /* Vic 94  */
+    {XVIDC_VM_3840x2160_30_P, 95, 3840, 2160, 30, 1},   /* Vic 95  */
+    {XVIDC_VM_3840x2160_50_P, 96, 3840, 2160, 50, 1},   /* Vic 96  */
+    {XVIDC_VM_3840x2160_60_P, 97, 3840, 2160, 60, 1},   /* Vic 97  */
+    {XVIDC_VM_3840x2160_100_P, 117, 3840, 2160, 100, 1}, /* Vic 117 */
+    {XVIDC_VM_3840x2160_120_P, 118, 3840, 2160, 120, 1}, /* Vic 118 */
+
+    /* 4096 x 2160 */
+    {XVIDC_VM_4096x2160_24_P, 98, 4096, 2160, 24, 3},   /* Vic 98  */
+    {XVIDC_VM_4096x2160_25_P, 99, 4096, 2160, 25, 3},   /* Vic 99  */
+    {XVIDC_VM_4096x2160_30_P, 100, 4096, 2160, 30, 3},  /* Vic 100 */
+    {XVIDC_VM_4096x2160_50_P, 101, 4096, 2160, 50, 3},  /* Vic 101 */
+    {XVIDC_VM_4096x2160_60_P, 102, 4096, 2160, 60, 3},  /* Vic 102 */
+    {XVIDC_VM_4096x2160_100_P, 218, 4096, 2160, 100, 3}, /* Vic 218 */
+    {XVIDC_VM_4096x2160_120_P, 219, 4096, 2160, 120, 3}, /* Vic 219 */
+
+    /* 5120 x 2160 */
+    {XVIDC_VM_5120x2160_24_P, 121, 5120, 2160, 24, 2},  /* Vic 121 */
+    {XVIDC_VM_5120x2160_25_P, 122, 5120, 2160, 25, 2},  /* Vic 122 */
+    {XVIDC_VM_5120x2160_30_P, 123, 5120, 2160, 30, 2},  /* Vic 123 */
+    {XVIDC_VM_5120x2160_50_P, 125, 5120, 2160, 50, 2},  /* Vic 125 */
+    {XVIDC_VM_5120x2160_60_P, 126, 5120, 2160, 60, 2},  /* Vic 126 */
+    {XVIDC_VM_5120x2160_100_P, 127, 5120, 2160, 100, 2}, /* Vic 127 */
+    {XVIDC_VM_5120x2160_120_P, 193, 5120, 2160, 120, 2}, /* Vic 193 */
+
+    /* 7680 x 4320 */
+    {XVIDC_VM_7680x4320_24_P, 194, 7680, 4320, 24, 1},  /* Vic 194 */
+    {XVIDC_VM_7680x4320_25_P, 195, 7680, 4320, 25, 1},  /* Vic 195 */
+    {XVIDC_VM_7680x4320_30_P, 196, 7680, 4320, 30, 1},  /* Vic 196 */
+    {XVIDC_VM_7680x4320_50_P, 198, 7680, 4320, 50, 1},  /* Vic 198 */
+    {XVIDC_VM_7680x4320_60_P, 199, 7680, 4320, 60, 1},  /* Vic 199 */
+    {XVIDC_VM_7680x4320_100_P, 200, 7680, 4320, 100, 1}, /* Vic 200 */
+    {XVIDC_VM_7680x4320_120_P, 201, 7680, 4320, 120, 1}, /* Vic 201 */
+
+    /* 10240 x 4320 */
+    {XVIDC_VM_10240x4320_24_P, 210, 10240, 4320, 24, 2},  /* Vic 210 */
+    {XVIDC_VM_10240x4320_25_P, 211, 10240, 4320, 25, 2},  /* Vic 211 */
+    {XVIDC_VM_10240x4320_30_P, 212, 10240, 4320, 30, 2},  /* Vic 212 */
+    {XVIDC_VM_10240x4320_50_P, 214, 10240, 4320, 50, 2},  /* Vic 214 */
+    {XVIDC_VM_10240x4320_60_P, 215, 10240, 4320, 60, 2},  /* Vic 215 */
+    {XVIDC_VM_10240x4320_100_P, 216, 10240, 4320, 100, 2}, /* Vic 216 */
+    {XVIDC_VM_10240x4320_120_P, 217, 10240, 4320, 120, 2}, /* Vic 217 */
+};
+
+/**
+* This table contains the attributes for various FRL Rate.
+* Each entry is of the format:
+* 1) Number of lanes
+* 2) Line Rate.
+*/
+const XHdmiC_FrlRate FrlRateTable[] = {
+    {3, 0},	/* XHDMIC_MAXFRLRATE_NOT_SUPPORTED */
+    {3, 3},	/* XHDMIC_MAXFRLRATE_3X3GBITSPS */
+    {3, 6},	/* XHDMIC_MAXFRLRATE_3X6GBITSPS */
+    {4, 6},	/* XHDMIC_MAXFRLRATE_4X6GBITSPS */
+    {4, 8},	/* XHDMIC_MAXFRLRATE_4X8GBITSPS */
+    {4, 10},	/* XHDMIC_MAXFRLRATE_4X10GBITSPS */
+    {4, 12},	/* XHDMIC_MAXFRLRATE_4X12GBITSPS */
+};
+
+/**
+* This table contains the CTS and N value of each TMDS character rate.
+* Each entry is of the format:
+* 1) Sample Frequency TMDS CLk, (32kHz, 44.1kHz, and 48kHz)
+*/
+const XHdmiC_TMDS_N_Table TMDSChar_N_Table[] =
+{
+	/* TMDSClk    32k   44k1   48k   88k2    96k  176k4   192k */
+	{        0, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 25200000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 27000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 31500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 33750000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 37800000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 40500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 50400000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 54000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 67500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 74250000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 81000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{ 92812500, { 8192, 6272, 12288, 12544, 24576, 25088, 49152}},
+	{108000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{111375000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{148500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{185625000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{222750000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{297000000, { 3072, 4704,  5120,  9408, 10240, 18816, 20480}},
+	{371250000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{445500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576}},
+	{594000000, { 3072, 9408,  6144, 18816, 12288, 37632, 24576}}
+};
+
+/**
+* This returns the the N Value based Audio Sampling Rate and TMDS
+* Character Rate
+*/
+u32 XHdmiC_TMDS_GetNVal(u32 TMDSCharRate,
+	XHdmiC_SamplingFrequency AudSampleFreq)
+{
+  XHdmiC_TMDS_N_Table const *item;
+  u32 i = 0;
+
+  /* Proceed only with supported Audio Sampling Frequency */
+  if (AudSampleFreq == XHDMIC_SAMPLING_FREQUENCY ||
+                  AudSampleFreq > XHDMIC_SAMPLING_FREQUENCY_192K) {
+          /* Since AudSampFreq not valid, return N Value = 0 */
+          return 0;
+  }
+
+  for(i = 0; i < sizeof(TMDSChar_N_Table)/sizeof(XHdmiC_TMDS_N_Table); i++) {
+    item = &TMDSChar_N_Table[i];
+    /* 10kHz  Tolerance */
+	if(TMDSCharRate <= (item->TMDSCharRate + 10000) &&
+			(TMDSCharRate >= (item->TMDSCharRate - 10000))) {
+      return item->ACR_NVal[AudSampleFreq-1];
+    }
+  }
+
+  /* If TMDS character rate could not be found return default values */
+  item = &TMDSChar_N_Table[0];
+
+  return item->ACR_NVal[AudSampleFreq-1];
+}
+
+/**
+* This returns the Audio Sampling Rate and TMDS
+* Character Rate.
+*
+* This function is not expected to be called for CTS/N as 0.
+*/
+XHdmiC_SamplingFrequency XHdmiC_TMDS_GetAudSampFreq(u32 TMDSCharRate,
+		u32 N, u32 CTSVal)
+{
+  XHdmiC_TMDS_N_Table const *item;
+  u8 i = 0;
+  u8 j = 0;
+  u64 fs;
+  u32 FsTol = 1000; /* Max Fs tolerance limit */
+
+  /* Look for standard TMDS rates */
+  for(i = 0; i < sizeof(TMDSChar_N_Table)/sizeof(XHdmiC_TMDS_N_Table); i++) {
+		item = &TMDSChar_N_Table[i];
+		if(TMDSCharRate <= (item->TMDSCharRate + 10000) &&
+			(TMDSCharRate >= (item->TMDSCharRate - 10000))) {
+			for (j = 0; j < 7; j++) {
+				if(N == item->ACR_NVal[j]) {
+					/*
+					 * starts from
+					 * XHDMIC_SAMPLING_FREQUENCY_32K
+					 */
+					return (j + 1);
+					break;
+				}
+			}
+		}
+  }
+
+  if (!CTSVal)
+          return XHDMIC_SAMPLING_FREQUENCY;
+
+ /* compute and approximate */
+  fs = ((u64)TMDSCharRate * (u64)N) ;
+  fs = fs / (128 * CTSVal);
+
+  if (((XHDMIC_SAMPLING_FREQ_32K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_32K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_32K;
+  else if (((XHDMIC_SAMPLING_FREQ_44_1K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_44_1K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_44_1K;
+  else if (((XHDMIC_SAMPLING_FREQ_48K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_48K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_48K;
+  else if (((XHDMIC_SAMPLING_FREQ_88_2K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_88_2K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_88_2K;
+  else if (((XHDMIC_SAMPLING_FREQ_96K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_96K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_96K;
+  else if (((XHDMIC_SAMPLING_FREQ_176_4K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_176_4K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_176_4K;
+  else if (((XHDMIC_SAMPLING_FREQ_192K - FsTol) <= fs) &&
+		  (fs <= (XHDMIC_SAMPLING_FREQ_192K + FsTol)))
+	  return XHDMIC_SAMPLING_FREQUENCY_192K;
+  else
+	  return  XHDMIC_SAMPLING_FREQUENCY; /* invalid */
+}
+
+/**
+* Top level data structure for XHdmiC_FRL_CTS_N_Table_t
+*/
+typedef struct {
+	/* 5 = FRL Rate 12,10,8,6,3 */
+	XHdmiC_FRL_CTS_N_Val CTS_NVal[5];
+} XHdmiC_FRL_CTS_N_Table_t;
+
+
+/**
+* This table contains the CTS and N value of each FRL character rate.
+* Each entry is of the format:
+* 1) Sample Frequency (32kHz, 44.1kHz, and 48kHz)
+*/
+const XHdmiC_FRL_CTS_N_Table_t FRL_CTS_N_Table[] =
+{
+	{/* 32kHz */
+		{	/* 3 Gbps */
+			{171875, {4224, 8448, 16896, 33792, 67584, 135168}},
+			/* 6 Gbps */
+			{328125, {4032, 8064, 16128, 32256, 64512, 129024}},
+			/* 8 Gbps */
+			{437500, {4032, 8064, 16128, 32256, 64512, 129024}},
+			/* 10 Gbps */
+			{468750, {3456, 6912, 13824, 27648, 55296, 110592}},
+			/* 12 Gbps */
+			{500000, {3072, 6144, 12288, 24576, 49152, 98304 }},
+		},
+	},
+	{/* 44.1kHz */
+		{
+			{156250 ,{5292 ,10584 ,21168 ,42336 ,84672 ,169344}},
+			{312500 ,{5292 ,10584 ,21168 ,42336 ,84672 ,169344}},
+			{312500 ,{3969 ,7938  ,15876 ,31752 ,63504 ,127008}},
+			{390625 ,{3969 ,7938  ,15876 ,31752 ,63504 ,127008}},
+			{468750 ,{3969 ,7938  ,15876 ,31752 ,63504 ,127008}},
+		},
+	},
+	{/* 48kHz */
+		{
+			{156250 ,{5760 ,11520 ,23040 ,46080 ,92160 ,184320}},
+			{328125 ,{6048 ,12096 ,24192 ,48384 ,96768 ,193536}},
+			{437500 ,{6048 ,12096 ,24192 ,48384 ,96768 ,193536}},
+			{468750 ,{5184 ,10368 ,20736 ,41472 ,82944 ,165888}},
+			{515625 ,{4752 ,9504  ,19008 ,38016 ,76032 ,152064}},
+		},
+	},
+};
+
+/**
+* This returns the N value in FRL mode based on its Audio Sample Frequency
+*/
+u32 XHdmiC_FRL_GetNVal(XHdmiC_FRLCharRate FRLCharRate,
+		XHdmiC_SamplingFrequencyVal AudSampleFreqVal)
+{
+	XHdmiC_FRL_CTS_N_Table_t const *item;
+	u8 SampleFreq;
+	u8 MultSampleFreq;
+	u8 FrlAudioCharRate = FRLCharRate;
+
+	/* Check for valid FRL Character Rate */
+	if (FrlAudioCharRate > R_666_667 ) {
+		/* Since AudSampFreq not valid, return N Value = 0 */
+		FrlAudioCharRate = R_166_667;
+	}
+
+	if (AudSampleFreqVal%XHDMIC_SAMPLING_FREQ_48K == 0) {
+		SampleFreq = 2;
+		MultSampleFreq = AudSampleFreqVal/XHDMIC_SAMPLING_FREQ_48K;
+	} else if (AudSampleFreqVal%XHDMIC_SAMPLING_FREQ_44_1K == 0) {
+		SampleFreq = 1;
+		MultSampleFreq = AudSampleFreqVal/XHDMIC_SAMPLING_FREQ_44_1K;
+	} else if (AudSampleFreqVal%XHDMIC_SAMPLING_FREQ_32K == 0) {
+		SampleFreq = 0;
+		MultSampleFreq = AudSampleFreqVal/XHDMIC_SAMPLING_FREQ_32K;
+	} else {
+		/* Not Valid Scenario */
+		SampleFreq = 0;
+		MultSampleFreq = 0;
+	}
+
+	/* MultSampleFreq is the divisible value from the 3 base
+	 * Sample Frequency.
+	 * However the N value array for FRL are based on the power of 2.
+	 * {base_freq*(2^0),base_freq*(2^1),base_freq*(2^2),base_freq*(2^3),..}
+	 */
+	switch (MultSampleFreq) {
+		case 1:
+		case 2:
+			MultSampleFreq = MultSampleFreq - 1;
+			break;
+
+		case 4:
+			MultSampleFreq = 2;
+			break;
+
+		case 8:
+			MultSampleFreq = 3;
+			break;
+
+		case 16:
+			MultSampleFreq = 4;
+			break;
+
+		case 32:
+			MultSampleFreq = 5;
+			break;
+
+		default:
+			MultSampleFreq = 0;
+			break;
+	}
+
+	item = &FRL_CTS_N_Table[SampleFreq];
+	return item->CTS_NVal[FrlAudioCharRate].ACR_NVal[MultSampleFreq];
+
+}
+
+/**
+* This returns the Audio Sample Frequency for FRL
+*/
+XHdmiC_SamplingFrequencyVal
+	XHdmiC_FRL_GetAudSampFreq(XHdmiC_FRLCharRate FRLCharRate,
+					u32 CTS, u32 N)
+{
+    XHdmiC_FRL_CTS_N_Table_t const *item;
+    u8 Index_0 = 0;
+    u8 Index_1 = 0;
+    XHdmiC_SamplingFrequencyVal SampleFreq = XHDMIC_SAMPLING_FREQ;
+
+    item = &FRL_CTS_N_Table[SampleFreq];
+    for (Index_0 = 0; Index_0 < 3; Index_0++) {
+        item = &FRL_CTS_N_Table[Index_0];
+        /* Adding tolerance of 10k CTS */
+        if ((CTS <  (item->CTS_NVal[FRLCharRate].ACR_CTSVal + 10000)) &&
+        (CTS >  (item->CTS_NVal[FRLCharRate].ACR_CTSVal - 10000))) {
+        	for (Index_1 = 0; Index_1 < 6; Index_1++) {
+        		if (N ==
+        			item->CTS_NVal[FRLCharRate].ACR_NVal[Index_1]){
+        			if (Index_0 == 0) {
+        				SampleFreq =
+        				XHDMIC_SAMPLING_FREQ_32K << Index_1;
+        			} else if (Index_0 == 1) {
+        				SampleFreq =
+        				XHDMIC_SAMPLING_FREQ_44_1K << Index_1;
+        			} else {
+        				SampleFreq =
+        				XHDMIC_SAMPLING_FREQ_48K << Index_1;
+        			}
+        			break;
+        		}
+        	}
+        }
+    }
+    return SampleFreq;
+}
+
+/**
+* This converts the Aud. Sampling Freq. Value to
+* Audio Info-frame Sampling Freq. Format.
+*/
+XHdmiC_SamplingFrequency
+	XHdmiC_GetAudIFSampFreq (XHdmiC_SamplingFrequencyVal AudSampFreqVal)
+{
+	XHdmiC_SamplingFrequency ExtACRSampFreq;
+
+	switch (AudSampFreqVal) {
+		case XHDMIC_SAMPLING_FREQ_32K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_32K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQ_44_1K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_44_1K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQ_48K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_48K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQ_88_2K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_88_2K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQ_96K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_96K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQ_176_4K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_176_4K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQ_192K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQUENCY_192K;
+		break;
+
+		default:
+			ExtACRSampFreq =
+					XHDMIC_SAMPLING_FREQ;
+		break;
+	}
+
+	return ExtACRSampFreq;
+}
+
+/**
+* This converts the Audio Info-frame Sampling Freq. Format. to
+* Audio Sampling Freq. Value.
+*/
+XHdmiC_SamplingFrequencyVal
+	XHdmiC_GetAudSampFreqVal(XHdmiC_SamplingFrequency AudSampFreqVal)
+{
+	XHdmiC_SamplingFrequencyVal ExtACRSampFreq;
+
+	switch (AudSampFreqVal) {
+		case XHDMIC_SAMPLING_FREQUENCY_32K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_32K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQUENCY_44_1K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_44_1K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQUENCY_48K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_48K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQUENCY_88_2K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_88_2K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQUENCY_96K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_96K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQUENCY_176_4K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_176_4K;
+		break;
+
+		case XHDMIC_SAMPLING_FREQUENCY_192K:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_192K;
+		break;
+
+		default:
+			ExtACRSampFreq =
+				XHDMIC_SAMPLING_FREQ_32K;
+		break;
+	}
+
+	return ExtACRSampFreq;
+}
+
+/*************************** Function Definitions *****************************/
+/**
+*
+* This function retrieves the Auxiliary Video Information Info Frame.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiC_ParseAVIInfoFrame(XHdmiC_Aux *AuxPtr, XHdmiC_AVI_InfoFrame *infoFramePtr)
+{
+	if (AuxPtr->Header.Byte[0] == AUX_AVI_INFOFRAME_TYPE) {
+
+		/* Header, Version */
+		infoFramePtr->Version = AuxPtr->Header.Byte[1];
+
+		/* PB1 */
+		infoFramePtr->ColorSpace = (AuxPtr->Data.Byte[1] >> 5) & 0x7;
+		infoFramePtr->ActiveFormatDataPresent = (AuxPtr->Data.Byte[1] >> 4) & 0x1;
+		infoFramePtr->BarInfo = (AuxPtr->Data.Byte[1] >> 2) & 0x3;
+		infoFramePtr->ScanInfo = AuxPtr->Data.Byte[1] & 0x3;
+
+		/* PB2 */
+		infoFramePtr->Colorimetry = (AuxPtr->Data.Byte[2] >> 6) & 0x3;
+		infoFramePtr->PicAspectRatio = (AuxPtr->Data.Byte[2] >> 4) & 0x3;
+		infoFramePtr->ActiveAspectRatio = AuxPtr->Data.Byte[2] & 0xf;
+
+		/* PB3 */
+		infoFramePtr->Itc = (AuxPtr->Data.Byte[3] >> 7) & 0x1;
+		infoFramePtr->ExtendedColorimetry = (AuxPtr->Data.Byte[3] >> 4) & 0x7;
+		infoFramePtr->QuantizationRange = (AuxPtr->Data.Byte[3] >> 2) & 0x3;
+		infoFramePtr->NonUniformPictureScaling = AuxPtr->Data.Byte[3] & 0x3;
+
+		/* PB4 */
+		infoFramePtr->VIC = AuxPtr->Data.Byte[4] & 0x7f;
+
+		/* PB5 */
+		infoFramePtr->YccQuantizationRange = (AuxPtr->Data.Byte[5] >> 6) & 0x3;
+		infoFramePtr->ContentType = (AuxPtr->Data.Byte[5] >> 4) & 0x3;
+		infoFramePtr->PixelRepetition = AuxPtr->Data.Byte[5] & 0xf;
+
+		/* PB6/7 */
+		infoFramePtr->TopBar = (AuxPtr->Data.Byte[8] << 8) | AuxPtr->Data.Byte[6];
+
+		/* PB8/9 */
+		infoFramePtr->BottomBar = (AuxPtr->Data.Byte[10] << 8) | AuxPtr->Data.Byte[9];
+
+		/* PB10/11 */
+		infoFramePtr->LeftBar = (AuxPtr->Data.Byte[12] << 8) | AuxPtr->Data.Byte[11];
+
+		/* PB12/13 */
+		infoFramePtr->RightBar = (AuxPtr->Data.Byte[14] << 8) | AuxPtr->Data.Byte[13];
+
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function retrieves the General Control Packet.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiC_ParseGCP(XHdmiC_Aux *AuxPtr, XHdmiC_GeneralControlPacket *GcpPtr)
+{
+	if (AuxPtr->Header.Byte[0] == AUX_GENERAL_CONTROL_PACKET_TYPE) {
+
+		/* SB0 */
+		GcpPtr->Clear_AVMUTE = (AuxPtr->Data.Byte[0] >> 4) & 0x1;
+		GcpPtr->Set_AVMUTE = AuxPtr->Data.Byte[0] & 0x1;
+
+		/* SB1 */
+		GcpPtr->PixelPackingPhase = (AuxPtr->Data.Byte[1] >> 4) & 0xf;
+		GcpPtr->ColorDepth = AuxPtr->Data.Byte[1] & 0xf;
+
+		/* SB2 */
+		GcpPtr->Default_Phase = AuxPtr->Data.Byte[2] & 0x1;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function retrieves the Audio Info Frame.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiC_ParseAudioInfoFrame(XHdmiC_Aux *AuxPtr, XHdmiC_AudioInfoFrame *AudIFPtr)
+{
+	if (AuxPtr->Header.Byte[0] == AUX_AUDIO_INFOFRAME_TYPE) {
+
+		/* HB1, Version */
+		AudIFPtr->Version = AuxPtr->Header.Byte[1];
+
+		/* PB1 */
+		AudIFPtr->CodingType = (AuxPtr->Data.Byte[1] >> 4) & 0xf;
+		AudIFPtr->ChannelCount = (AuxPtr->Data.Byte[1]) & 0x7;
+
+		/* PB2 */
+		AudIFPtr->SampleFrequency = (AuxPtr->Data.Byte[2] >> 2) & 0x7;
+		AudIFPtr->SampleSize = AuxPtr->Data.Byte[2] & 0x3;
+
+		/* PB4 */
+		AudIFPtr->ChannelAllocation = AuxPtr->Data.Byte[4];
+
+		/* PB5 */
+		AudIFPtr->Downmix_Inhibit = (AuxPtr->Data.Byte[5] >> 7) & 0x1;
+		AudIFPtr->LevelShiftVal = (AuxPtr->Data.Byte[5] >> 4) & 0xf;
+		AudIFPtr->LFE_Playback_Level = AuxPtr->Data.Byte[5] & 0x3;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function retrieves the Audio Metadata.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiC_ParseAudioMetadata(XHdmiC_Aux *AuxPtr,
+		XHdmiC_AudioMetadata *AudMetadata)
+{
+	if (AuxPtr->Header.Byte[0] == AUX_AUDIO_METADATA_PACKET_TYPE) {
+		/* 3D Audio */
+		AudMetadata->Audio3D = AuxPtr->Header.Byte[1] & 0x1;
+
+		/* HB2 */
+		AudMetadata->Num_Audio_Str =
+				(AuxPtr->Header.Byte[2] >> 2) & 0x3;
+		AudMetadata->Num_Views = AuxPtr->Header.Byte[2] & 0x3;
+
+		/* PB0 */
+		AudMetadata->Audio3D_ChannelCount =
+				AuxPtr->Data.Byte[0] & 0x1F;
+
+		/* PB1 */
+		AudMetadata->ACAT = AuxPtr->Data.Byte[1] & 0x0F;
+
+		/* PB2 */
+		AudMetadata->Audio3D_ChannelAllocation =
+				AuxPtr->Data.Byte[2] & 0xFF;
+	}
+}
+
+/*****************************************************************************/
+/**
+ *
+ * This function retrieves the SPD Infoframes.
+ *
+ * @param  None.
+ *
+ * @return None.
+ *
+ * @note   None.
+ *
+******************************************************************************/
+void XV_HdmiC_ParseSPDIF(XHdmiC_Aux *AuxPtr, XHdmiC_SPDInfoFrame *SPDInfoFrame)
+{
+	if (AuxPtr->Header.Byte[0] == AUX_SPD_INFOFRAME_TYPE) {
+		/* 3D Audio */
+		SPDInfoFrame->Version = AuxPtr->Header.Byte[1];
+
+		/* Vendor Name Characters */
+		SPDInfoFrame->VN1 = AuxPtr->Data.Byte[1];
+		SPDInfoFrame->VN2 = AuxPtr->Data.Byte[2];
+		SPDInfoFrame->VN3 = AuxPtr->Data.Byte[3];
+		SPDInfoFrame->VN4 = AuxPtr->Data.Byte[4];
+		SPDInfoFrame->VN5 = AuxPtr->Data.Byte[5];
+		SPDInfoFrame->VN6 = AuxPtr->Data.Byte[6];
+		SPDInfoFrame->VN7 = AuxPtr->Data.Byte[8];
+		SPDInfoFrame->VN8 = AuxPtr->Data.Byte[9];
+
+		/* Product Description Character */
+		SPDInfoFrame->PD1 = AuxPtr->Data.Byte[10];
+		SPDInfoFrame->PD2 = AuxPtr->Data.Byte[11];
+		SPDInfoFrame->PD3 = AuxPtr->Data.Byte[12];
+		SPDInfoFrame->PD4 = AuxPtr->Data.Byte[13];
+		SPDInfoFrame->PD5 = AuxPtr->Data.Byte[14];
+		SPDInfoFrame->PD6 = AuxPtr->Data.Byte[16];
+		SPDInfoFrame->PD7 = AuxPtr->Data.Byte[17];
+		SPDInfoFrame->PD8 = AuxPtr->Data.Byte[18];
+		SPDInfoFrame->PD9 = AuxPtr->Data.Byte[19];
+		SPDInfoFrame->PD10 = AuxPtr->Data.Byte[20];
+		SPDInfoFrame->PD11 = AuxPtr->Data.Byte[21];
+		SPDInfoFrame->PD12 = AuxPtr->Data.Byte[22];
+		SPDInfoFrame->PD13 = AuxPtr->Data.Byte[24];
+		SPDInfoFrame->PD14 = AuxPtr->Data.Byte[25];
+		SPDInfoFrame->PD15 = AuxPtr->Data.Byte[26];
+		SPDInfoFrame->PD16 = AuxPtr->Data.Byte[27];
+
+		/* Source Information */
+		SPDInfoFrame->SourceInfo = AuxPtr->Data.Byte[28];
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function retrieves the DRM Infoframes.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiC_ParseDRMIF(XHdmiC_Aux *AuxPtr, struct v4l2_hdr10_payload *DRMInfoFrame)
+{
+	if (AuxPtr->Header.Byte[0] == AUX_DRM_INFOFRAME_TYPE) {
+
+		/* Vendor Name Characters */
+		DRMInfoFrame->eotf = AuxPtr->Data.Byte[1] & 0x7;
+
+		DRMInfoFrame->metadata_type =
+				AuxPtr->Data.Byte[2] & 0x7;
+
+		DRMInfoFrame->display_primaries[0].x =
+				(AuxPtr->Data.Byte[3] & 0xFF) |
+				(AuxPtr->Data.Byte[4] << 8);
+
+		DRMInfoFrame->display_primaries[0].y =
+				(AuxPtr->Data.Byte[5] & 0xFF) |
+				(AuxPtr->Data.Byte[6] << 8);
+
+		DRMInfoFrame->display_primaries[1].x =
+				(AuxPtr->Data.Byte[8] & 0xFF) |
+				(AuxPtr->Data.Byte[9] << 8);
+
+		DRMInfoFrame->display_primaries[1].y =
+				(AuxPtr->Data.Byte[10] & 0xFF) |
+				(AuxPtr->Data.Byte[11] << 8);
+
+		DRMInfoFrame->display_primaries[2].x =
+				(AuxPtr->Data.Byte[12] & 0xFF) |
+				(AuxPtr->Data.Byte[13] << 8);
+
+		DRMInfoFrame->display_primaries[2].y =
+				(AuxPtr->Data.Byte[14] & 0xFF) |
+				(AuxPtr->Data.Byte[16] << 8);
+
+		DRMInfoFrame->white_point.x =
+				(AuxPtr->Data.Byte[17] & 0xFF) |
+				(AuxPtr->Data.Byte[18] << 8);
+
+		DRMInfoFrame->white_point.y =
+				(AuxPtr->Data.Byte[19] & 0xFF) |
+				(AuxPtr->Data.Byte[20] << 8);
+
+		DRMInfoFrame->max_mdl =
+				(AuxPtr->Data.Byte[21] & 0xFF) |
+				(AuxPtr->Data.Byte[22] << 8);
+
+		DRMInfoFrame->min_mdl =
+				(AuxPtr->Data.Byte[24] & 0xFF) |
+				(AuxPtr->Data.Byte[25] << 8);
+
+		DRMInfoFrame->max_cll =
+				(AuxPtr->Data.Byte[26] & 0xFF) |
+				(AuxPtr->Data.Byte[27] << 8);
+
+		DRMInfoFrame->max_fall =
+				(AuxPtr->Data.Byte[28] & 0xFF) |
+				(AuxPtr->Data.Byte[29] << 8);
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function generates and sends Auxilliary Video Infoframes
+*
+* @param  InstancePtr is a pointer to the HDMI TX Subsystem instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_Aux XV_HdmiC_AVIIF_GeneratePacket(XHdmiC_AVI_InfoFrame *infoFramePtr)
+{
+//	Xil_AssertNonvoid(infoFramePtr != NULL);
+
+	u8 Index;
+	u8 Crc;
+	XHdmiC_Aux aux;
+
+	(void)memset((void *)&aux, 0, sizeof(XHdmiC_Aux));
+
+	/* Header, Packet type*/
+	aux.Header.Byte[0] = AUX_AVI_INFOFRAME_TYPE;
+
+	/* Version */
+	aux.Header.Byte[1] = infoFramePtr->Version;
+
+	/* Length */
+	aux.Header.Byte[2] = 13;
+
+	/* Checksum (this will be calculated by the HDMI TX IP) */
+	aux.Header.Byte[3] = 0;
+
+	/* PB1 */
+   aux.Data.Byte[1] = (infoFramePtr->ColorSpace & 0x7) << 5 |
+		   ((infoFramePtr->ActiveFormatDataPresent << 4) & 0x10) |
+		   ((infoFramePtr->BarInfo << 2) & 0xc) |
+		   (infoFramePtr->ScanInfo & 0x3);
+
+   /* PB2 */
+   aux.Data.Byte[2] = ((infoFramePtr->Colorimetry & 0x3) << 6  |
+		   ((infoFramePtr->PicAspectRatio << 4) & 0x30) |
+		   (infoFramePtr->ActiveAspectRatio & 0xf));
+
+   /* PB3 */
+   aux.Data.Byte[3] = (infoFramePtr->Itc & 0x1) << 7 |
+		   ((infoFramePtr->ExtendedColorimetry << 4) & 0x70) |
+		   ((infoFramePtr->QuantizationRange << 2) & 0xc) |
+		   (infoFramePtr->NonUniformPictureScaling & 0x3);
+
+   /* PB4 */
+   aux.Data.Byte[4] = infoFramePtr->VIC;
+
+   /* PB5 */
+   aux.Data.Byte[5] = (infoFramePtr->YccQuantizationRange & 0x3) << 6 |
+		   ((infoFramePtr->ContentType << 4) & 0x30) |
+		   (infoFramePtr->PixelRepetition & 0xf);
+
+   /* PB6 */
+   aux.Data.Byte[6] = infoFramePtr->TopBar & 0xff;
+
+   aux.Data.Byte[7] = 0;
+
+   /* PB8 */
+   aux.Data.Byte[8] = (infoFramePtr->TopBar & 0xff00) >> 8;
+
+   /* PB9 */
+   aux.Data.Byte[9] = infoFramePtr->BottomBar & 0xff;
+
+   /* PB10 */
+   aux.Data.Byte[10] = (infoFramePtr->BottomBar & 0xff00) >> 8;
+
+   /* PB11 */
+   aux.Data.Byte[11] = infoFramePtr->LeftBar & 0xff;
+
+   /* PB12 */
+   aux.Data.Byte[12] = (infoFramePtr->LeftBar & 0xff00) >> 8;
+
+   /* PB13 */
+   aux.Data.Byte[13] = infoFramePtr->RightBar & 0xff;
+
+   /* PB14 */
+   aux.Data.Byte[14] = (infoFramePtr->RightBar & 0xff00) >> 8;
+
+   /* Index references the length to calculate start of loop from where values are reserved */
+   for (Index = aux.Header.Byte[2] + 2; Index < 32; Index++) {
+	   aux.Data.Byte[Index] = 0;
+   }
+
+   /* Calculate AVI infoframe checksum */
+   Crc = 0;
+
+   /* Header */
+   for (Index = 0; Index < 3; Index++) {
+     Crc += aux.Header.Byte[Index];
+   }
+
+   /* Data */
+   for (Index = 1; Index < (aux.Header.Byte[2] + 2); Index++) {
+     Crc += aux.Data.Byte[Index];
+   }
+
+   Crc = 256 - Crc;
+
+   /* PB0 */
+   aux.Data.Byte[0] = Crc;
+
+   return aux;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function generates and sends Audio Infoframes
+*
+* @param  InstancePtr is a pointer to the HDMI TX Subsystem instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_Aux XV_HdmiC_AudioIF_GeneratePacket(XHdmiC_AudioInfoFrame *AudioInfoFrame)
+{
+//	Xil_AssertNonvoid(AudioInfoFrame != NULL);
+
+	u8 Index;
+	u8 Crc;
+	XHdmiC_Aux aux;
+
+	(void)memset((void *)&aux, 0, sizeof(XHdmiC_Aux));
+
+	/* Header, Packet Type */
+	aux.Header.Byte[0] = AUX_AUDIO_INFOFRAME_TYPE;
+
+	/* Version */
+	aux.Header.Byte[1] = 0x01;
+
+	/* Length */
+	aux.Header.Byte[2] = 0x0A;
+
+	aux.Header.Byte[3] = 0;
+
+	/* PB1 */
+	aux.Data.Byte[1] = AudioInfoFrame->CodingType << 4 |
+			(AudioInfoFrame->ChannelCount & 0x7);
+
+	/* PB2 */
+	aux.Data.Byte[2] = ((AudioInfoFrame->SampleFrequency << 2) & 0x1c) |
+			(AudioInfoFrame->SampleSize & 0x3);
+
+	/* PB3 */
+	aux.Data.Byte[3] = 0;
+
+
+	/* PB4 */
+	aux.Data.Byte[4] = AudioInfoFrame->ChannelAllocation;
+
+	/* PB5 */
+	aux.Data.Byte[5] = (AudioInfoFrame->Downmix_Inhibit << 7) |
+			((AudioInfoFrame->LevelShiftVal << 3) & 0x78) |
+			(AudioInfoFrame->LFE_Playback_Level & 0x3);
+
+	for (Index = 6; Index < 32; Index++)
+	{
+		aux.Data.Byte[Index] = 0;
+	}
+
+	/* Calculate Audio infoframe checksum */
+	  Crc = 0;
+
+	  /* Header */
+	  for (Index = 0; Index < 3; Index++) {
+	    Crc += aux.Header.Byte[Index];
+	  }
+
+	  /* Data */
+	  for (Index = 1; Index < aux.Header.Byte[2] + 1; Index++) {
+		  Crc += aux.Data.Byte[Index];
+	  }
+
+	  Crc = 256 - Crc;
+
+	  aux.Data.Byte[0] = Crc;
+
+	  return aux;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function generates and sends Audio Metadata Packet
+*
+* @param  InstancePtr is a pointer to the HDMI TX Subsystem instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_Aux XV_HdmiC_AudioMetadata_GeneratePacket(XHdmiC_AudioMetadata
+		*AudMetadata)
+{
+	u8 Index;
+	XHdmiC_Aux aux;
+
+	(void)memset((void *)&aux, 0, sizeof(XHdmiC_Aux));
+
+	/* Header, Packet Type */
+	aux.Header.Byte[0] = AUX_AUDIO_METADATA_PACKET_TYPE;
+
+	/* 3D Audio */
+	aux.Header.Byte[1] = AudMetadata->Audio3D & 0x1;
+
+	/* HB2 */
+	aux.Header.Byte[2] = ((AudMetadata->Num_Audio_Str & 0x3) << 2) |
+			(AudMetadata->Num_Views & 0x3);
+
+	/* HB3 */
+	aux.Header.Byte[3] = 0;
+
+	/* PB0 */
+	aux.Data.Byte[0] = AudMetadata->Audio3D_ChannelCount & 0x1F;
+
+	/* PB1 */
+	aux.Data.Byte[1] = AudMetadata->ACAT & 0x0F;
+
+	/* PB2 */
+	aux.Data.Byte[2] = AudMetadata->Audio3D_ChannelAllocation & 0xFF;
+
+	for (Index = 3; Index < 32; Index++)
+		aux.Data.Byte[Index] = 0;
+
+	return aux;
+}
+
+/*****************************************************************************/
+/**
+ *
+ * This function generates and sends SPD Infoframes
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem instance.
+ *
+ * @return None.
+ *
+ * @note   None.
+ *
+******************************************************************************/
+XHdmiC_Aux XV_HdmiC_SPDIF_GeneratePacket(XHdmiC_SPDInfoFrame *SPDInfoFrame)
+{
+	u8 Index;
+	u8 Crc;
+	XHdmiC_Aux aux;
+
+	(void)memset((void *)&aux, 0, sizeof(XHdmiC_Aux));
+
+	/* Header, Packet Type */
+	aux.Header.Byte[0] = AUX_SPD_INFOFRAME_TYPE;
+
+	/* 3D Audio */
+	aux.Header.Byte[1] = SPDInfoFrame->Version;
+
+	/* Length of SPD InfoFrame */
+	aux.Header.Byte[2] = 25;
+
+	/* HB3 */
+	aux.Header.Byte[3] = 0; /* CRC */
+
+	/* Vendor Name Characters */
+	aux.Data.Byte[0] = 0; /* CRC */
+	aux.Data.Byte[1] = SPDInfoFrame->VN1;
+	aux.Data.Byte[2] = SPDInfoFrame->VN2;
+	aux.Data.Byte[3] = SPDInfoFrame->VN3;
+	aux.Data.Byte[4] = SPDInfoFrame->VN4;
+	aux.Data.Byte[5] = SPDInfoFrame->VN5;
+	aux.Data.Byte[6] = SPDInfoFrame->VN6;
+	aux.Data.Byte[7] = 0; /* ECC */
+	aux.Data.Byte[8] = SPDInfoFrame->VN7;
+	aux.Data.Byte[9] = SPDInfoFrame->VN8;
+
+	/* Product Description Character */
+	aux.Data.Byte[10] = SPDInfoFrame->PD1;
+	aux.Data.Byte[11] = SPDInfoFrame->PD2;
+	aux.Data.Byte[12] = SPDInfoFrame->PD3;
+	aux.Data.Byte[13] = SPDInfoFrame->PD4;
+	aux.Data.Byte[14] = SPDInfoFrame->PD5;
+	aux.Data.Byte[15] = 0; /* ECC */
+	aux.Data.Byte[16] = SPDInfoFrame->PD6;
+	aux.Data.Byte[17] = SPDInfoFrame->PD7;
+	aux.Data.Byte[18] = SPDInfoFrame->PD8;
+	aux.Data.Byte[19] = SPDInfoFrame->PD9;
+	aux.Data.Byte[20] = SPDInfoFrame->PD10;
+	aux.Data.Byte[21] = SPDInfoFrame->PD11;
+	aux.Data.Byte[22] = SPDInfoFrame->PD12;
+	aux.Data.Byte[23] = 0; /* ECC */
+	aux.Data.Byte[24] = SPDInfoFrame->PD13;
+	aux.Data.Byte[25] = SPDInfoFrame->PD14;
+	aux.Data.Byte[26] = SPDInfoFrame->PD15;
+	aux.Data.Byte[27] = SPDInfoFrame->PD16;
+
+	/* Source Information */
+	aux.Data.Byte[28] = SPDInfoFrame->SourceInfo;
+	aux.Data.Byte[29] = 0;
+	aux.Data.Byte[30] = 0;
+	aux.Data.Byte[31] = 0; /* ECC */
+
+	/* Calculate SPD infoframe checksum */
+	Crc = 0;
+
+	/* Header */
+	for (Index = 0; Index < 3; Index++)
+		Crc += aux.Header.Byte[Index];
+
+	/* Data */
+	for (Index = 1; Index < aux.Header.Byte[2] + 4; Index++)
+		Crc += aux.Data.Byte[Index];
+
+	Crc = 256 - Crc;
+
+	aux.Data.Byte[0] = Crc;
+
+	return aux;
+}
+
+/*****************************************************************************/
+/**
+ *
+ * This function generates and sends DRM Infoframes
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem instance.
+ *
+ * @return None.
+ *
+ * @note   None.
+ *
+******************************************************************************/
+void XV_HdmiC_DRMIF_GeneratePacket(struct v4l2_hdr10_payload *DRMInfoFrame, XHdmiC_Aux *aux)
+{
+	u8 Index;
+	u8 Crc;
+
+	memset(aux, 0, sizeof(XHdmiC_Aux));
+
+	/* Header, Packet Type */
+	aux->Header.Byte[0] = AUX_DRM_INFOFRAME_TYPE;
+
+	/* Version Refer CEA-861-G */
+	aux->Header.Byte[1] = 0x1;
+
+	/* Length of DRM InfoFrame */
+	aux->Header.Byte[2] = 26;
+
+	/* HB3 */
+	aux->Header.Byte[3] = 0; /* CRC */
+
+	/* Vendor Name Characters */
+	aux->Data.Byte[0] = 0; /* CRC */
+	aux->Data.Byte[1] = DRMInfoFrame->eotf & 0x7;
+
+	aux->Data.Byte[2] = DRMInfoFrame->metadata_type & 0x7;
+
+	aux->Data.Byte[3] = DRMInfoFrame->display_primaries[0].x & 0xFF;
+	aux->Data.Byte[4] = DRMInfoFrame->display_primaries[0].x >> 8;
+
+	aux->Data.Byte[5] = DRMInfoFrame->display_primaries[0].y & 0xFF;
+	aux->Data.Byte[6] = DRMInfoFrame->display_primaries[0].y >> 8;
+	aux->Data.Byte[7] = 0; /* ECC */
+
+	aux->Data.Byte[8] = DRMInfoFrame->display_primaries[1].x & 0xFF;
+	aux->Data.Byte[9] = DRMInfoFrame->display_primaries[1].x >> 8;
+
+	aux->Data.Byte[10] = DRMInfoFrame->display_primaries[1].y & 0xFF;
+	aux->Data.Byte[11] = DRMInfoFrame->display_primaries[1].y >> 8;
+
+	aux->Data.Byte[12] = DRMInfoFrame->display_primaries[2].x & 0xFF;
+	aux->Data.Byte[13] = DRMInfoFrame->display_primaries[2].x >> 8;
+
+	aux->Data.Byte[14] = DRMInfoFrame->display_primaries[2].y & 0xFF;
+	aux->Data.Byte[15] = 0; /* ECC */
+	aux->Data.Byte[16] = DRMInfoFrame->display_primaries[2].y >> 8;
+
+	aux->Data.Byte[17] = DRMInfoFrame->white_point.x & 0xFF;
+	aux->Data.Byte[18] = DRMInfoFrame->white_point.x >> 8;
+
+	aux->Data.Byte[19] = DRMInfoFrame->white_point.y & 0xFF;
+	aux->Data.Byte[20] = DRMInfoFrame->white_point.y >> 8;
+
+	aux->Data.Byte[21] = DRMInfoFrame->max_mdl & 0xFF;
+	aux->Data.Byte[22] = DRMInfoFrame->max_mdl >> 8;
+	aux->Data.Byte[23] = 0; /* ECC */
+
+	aux->Data.Byte[24] = DRMInfoFrame->min_mdl & 0xFF;
+	aux->Data.Byte[25] = DRMInfoFrame->min_mdl >> 8;
+
+	aux->Data.Byte[26] = DRMInfoFrame->max_cll & 0xFF;
+	aux->Data.Byte[27] = DRMInfoFrame->max_cll >> 8;
+
+	aux->Data.Byte[28] = DRMInfoFrame->max_fall & 0xFF;
+	aux->Data.Byte[29] = DRMInfoFrame->max_fall >> 8;
+
+	aux->Data.Byte[30] = 0;
+	aux->Data.Byte[31] = 0; /* ECC */
+
+	/* Calculate DRM infoframe checksum */
+	Crc = 0;
+
+	/* Header */
+	for (Index = 0; Index < 3; Index++)
+		Crc += aux->Header.Byte[Index];
+
+	/* Data */
+	for (Index = 1; Index < aux->Header.Byte[2] + 4; Index++)
+		Crc += aux->Data.Byte[Index];
+
+	Crc = 256 - Crc;
+
+	aux->Data.Byte[0] = Crc;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts the XVidC_ColorFormat to XHdmiC_Colorspace
+*
+* @param  ColorFormat is the XVidC_ColorFormat value to be converted
+*
+* @return XHdmiC_Colorspace value.
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_Colorspace XV_HdmiC_XVidC_To_IfColorformat(XVidC_ColorFormat ColorFormat) {
+	XHdmiC_Colorspace Colorspace;
+
+	switch(ColorFormat) {
+		case XVIDC_CSF_RGB :
+			Colorspace = XHDMIC_COLORSPACE_RGB;
+			break;
+
+		case XVIDC_CSF_YCRCB_422 :
+			Colorspace = XHDMIC_COLORSPACE_YUV422;
+			break;
+
+		case XVIDC_CSF_YCRCB_444 :
+			Colorspace = XHDMIC_COLORSPACE_YUV444;
+			break;
+
+		case XVIDC_CSF_YCRCB_420 :
+			Colorspace = XHDMIC_COLORSPACE_YUV420;
+			break;
+
+		default:
+			Colorspace = XHDMIC_COLORSPACE_RESERVED;
+			break;
+	}
+
+	return Colorspace;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts the XVidC_ColorDepth to XHdmiC_ColorDepth
+*
+* @param  Bpc is the XVidC_ColorDepth value to be converted
+*
+* @return XHdmiC_ColorDepth value.
+*
+* @note   None.
+*
+******************************************************************************/
+XVidC_AspectRatio XV_HdmiC_IFAspectRatio_To_XVidC(XHdmiC_PicAspectRatio AR) {
+	XVidC_AspectRatio AspectRatio;
+
+	switch(AR) {
+		case XHDMIC_PIC_ASPECT_RATIO_4_3 :
+			AspectRatio = XVIDC_AR_4_3;
+			break;
+
+		case XHDMIC_PIC_ASPECT_RATIO_16_9 :
+			AspectRatio = XVIDC_AR_16_9;
+			break;
+
+		default:
+			AspectRatio = XVIDC_AR_16_9;
+			break;
+	}
+
+	return AspectRatio;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic.h
@@ -0,0 +1,586 @@
+/*******************************************************************************
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xhdmic.h
+ * @{
+ * @details
+ *
+ * Contains common structures, definitions, macros, and utility functions that
+ * are typically used by hdmi-related drivers and applications.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   EB   21/12/17 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+#ifndef XV_HDMIC_H_  /* Prevent circular inclusions by
+                              using protection macros. */
+#define XV_HDMIC_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+#include <linux/clk.h>
+#include <uapi/linux/videodev2.h>
+#include <media/hdr-ctrls.h>
+#include "xil_types.h"
+#include "xil_printf.h"
+#include "xvidc.h"
+#include "xil_assert.h"
+
+/************************** Constant Definitions ******************************/
+#define VICTABLE_SIZE 126
+#define AUX_VSIF_TYPE 0x81
+#define AUX_AVI_INFOFRAME_TYPE 0x82
+#define AUX_GENERAL_CONTROL_PACKET_TYPE 0x3
+#define AUX_AUDIO_INFOFRAME_TYPE 0x84
+#define AUX_AUDIO_METADATA_PACKET_TYPE 0x0D
+#define AUX_SPD_INFOFRAME_TYPE 0x83
+#define AUX_DRM_INFOFRAME_TYPE 0x87
+
+/****************************** Type Definitions ******************************/
+
+/**
+* This typedef contains Video identification information in tabular form.
+*/
+typedef struct {
+	XVidC_VideoMode VmId;	/**< Video mode/Resolution ID */
+	u8 Vic;			/**< Video Identification code */
+	u32 Width;		/**< Width of the Video Resolution */
+	u32 Height;		/**< Height of the Video Resolution */
+	u16 FrameRate;		/**< Frame Rate */
+	u16 AspectRatio;	/**< Aspect Ratio of Video */
+} XHdmiC_VicTable;
+
+typedef union {
+    u32 Data;   /**< AUX header data field */
+    u8 Byte[4]; /**< AUX header byte field */
+} XHdmiC_AuxHeader;
+
+typedef union {
+    u32 Data[8];    /**< AUX data field */
+    u8 Byte[32];    /**< AUX data byte field */
+} XHdmiC_AuxData;
+
+typedef struct {
+	XHdmiC_AuxHeader Header; /**< AUX header field */
+	XHdmiC_AuxData Data;     /**< AUX data field */
+} XHdmiC_Aux;
+
+typedef enum {
+	XHDMIC_COLORSPACE_RGB,
+	XHDMIC_COLORSPACE_YUV422,
+	XHDMIC_COLORSPACE_YUV444,
+	XHDMIC_COLORSPACE_YUV420,	/**< Version 3 AVI InfoFrame */
+	XHDMIC_COLORSPACE_RESERVED,
+	XHDMIC_COLORSPACE_IDO_DEFINED = 7,
+} XHdmiC_Colorspace;
+
+typedef enum {
+	XHDMIC_ACTIVE_ASPECT_16_9_TOP = 2,
+	XHDMIC_ACTIVE_ASPECT_14_9_TOP = 3,
+	XHDMIC_ACTIVE_ASPECT_16_9_CENTER = 4,
+	XHDMIC_ACTIVE_ASPECT_PICTURE = 8,
+	XHDMIC_ACTIVE_ASPECT_4_3 = 9,
+	XHDMIC_ACTIVE_ASPECT_16_9 = 10,
+	XHDMIC_ACTIVE_ASPECT_14_9 = 11,
+	XHDMIC_ACTIVE_ASPECT_4_3_SP_14_9 = 13,
+	XHDMIC_ACTIVE_ASPECT_16_9_SP_14_9 = 14,
+	XHDMIC_ACTIVE_ASPECT_16_9_SP_4_3 = 15
+} XHdmiC_ActiveAspectRatio;
+
+typedef enum {
+	XHDMIC_BAR_INFO_NA,
+	XHDMIC_BAR_INFO_VERT_BAR,
+	XHDMIC_BAR_INFO_HORI_BAR,
+	XHDMIC_BAR_INFO_VERT_AND_HORI_BAR
+} XHdmiC_BarInfo;
+
+typedef enum {
+	XHDMIC_SCAN_INFO_NA,
+	XHDMIC_SCAN_INFO_OVERSCAN,
+	XHDMIC_SCAN_INFO_UNDERSCAN,
+	XHDMIC_SCAN_INFO_RESERVED
+} XHdmiC_ScanInfo;
+
+typedef enum {
+	XHDMIC_COLORIMETRY_NA,
+	XHDMIC_COLORIMETRY_ITU_601,
+	XHDMIC_COLORIMETRY_ITU709,
+	XHDMIC_COLORIMETRY_EXTENDED
+} XHdmiC_Colorimetry;
+
+typedef enum {
+	XHDMIC_PIC_ASPECT_RATIO_NA,
+	XHDMIC_PIC_ASPECT_RATIO_4_3,
+	XHDMIC_PIC_ASPECT_RATIO_16_9,
+	XHDMIC_PIC_ASPECT_RATIO_RESERVED
+} XHdmiC_PicAspectRatio;
+
+typedef enum {
+	XHDMIC_EXTENDED_COLORIMETRY_YCC_601,
+	XHDMIC_EXTENDED_COLORIMETRY_YCC_709,
+	XHDMIC_EXTENDED_COLORIMETRY_S_YCC_601,
+	XHDMIC_EXTENDED_COLORIMETRY_ADOBE_YCC_601,
+	XHDMIC_EXTENDED_COLORIMETRY_ADOBE_RGB,
+	XHDMIC_EXTENDED_COLORIMETRY_RESERVED_1,
+	XHDMIC_EXTENDED_COLORIMETRY_RESERVED_2,
+	XHDMIC_EXTENDED_COLORIMETRY_RESERVED_3
+} XHdmiC_ExtendedColorimetry;
+
+typedef enum {
+	XHDMIC_RGB_QUANTIZATION_RANGE_DEFAULT,
+	XHDMIC_RGB_QUANTIZATION_RANGE_LIMITED,
+	XHDMIC_RGB_QUANTIZATION_RANGE_FULL
+} XHdmiC_RGBQuantizationRange;
+
+typedef enum{
+	XHDMIC_PIXEL_REPETITION_FACTOR_1,
+	XHDMIC_PIXEL_REPETITION_FACTOR_2,
+	XHDMIC_PIXEL_REPETITION_FACTOR_3,
+	XHDMIC_PIXEL_REPETITION_FACTOR_4,
+	XHDMIC_PIXEL_REPETITION_FACTOR_5,
+	XHDMIC_PIXEL_REPETITION_FACTOR_6,
+	XHDMIC_PIXEL_REPETITION_FACTOR_7,
+	XHDMIC_PIXEL_REPETITION_FACTOR_8,
+	XHDMIC_PIXEL_REPETITION_FACTOR_9,
+	XHDMIC_PIXEL_REPETITION_FACTOR_10
+} XHdmiC_PixelRepetitionFactor;
+
+typedef enum {
+	XHDMIC_YCC_QUANTIZATION_RANGE_LIMITED,
+	XHDMIC_YCC_QUANTIZATION_RANGE_FULL,
+	XHDMIC_YCC_QUANTIZATION_RANGE_RESERVED_1,
+	XHDMIC_YCC_QUANTIZATION_RANGE_RESERVED_2
+} XHdmiC_YccQuantizationRange;
+
+typedef enum {
+	XHDMIC_NON_UNIFORM_PICTURE_SCALING_NA,
+	XHDMIC_NON_UNIFORM_PICTURE_SCALING_HORI,
+	XHDMIC_NON_UNIFORM_PICTURE_SCALING_VERT,
+	XHDMIC_NON_UNIFORM_PICTURE_SCALING_VERT_AND_HORI_SCALING
+} XHdmiC_NonUniformPictureScaling;
+
+typedef enum {
+	XHDMIC_CONTENT_TYPE_GRAPHICS,
+	XHDMIC_CONTENT_TYPE_PHOTO,
+	XHDMIC_CONTENT_TYPE_CINEMA,
+	XHDMIC_CONTENT_TYPE_GAME
+} XHdmiC_ContentType;
+
+typedef enum {
+	XHDMIC_COLORDEPTH_NOT_INDICATED,
+	XHDMIC_COLORDEPTH_24 = 4,
+	XHDMIC_COLORDEPTH_30,
+	XHDMIC_COLORDEPTH_36,
+	XHDMIC_COLORDEPTH_48
+} XHdmiC_ColorDepth;
+
+typedef enum {
+	XHDMIC_PIXELPACKINGPHASE_4,
+	XHDMIC_PIXELPACKINGPHASE_1,
+	XHDMIC_PIXELPACKINGPHASE_2,
+	XHDMIC_PIXELPACKINGPHASE_3
+} XHdmiC_PixelPackingPhase;
+
+typedef enum {
+	XHDMIC_SAMPLING_FREQUENCY,
+	XHDMIC_SAMPLING_FREQUENCY_32K,
+	XHDMIC_SAMPLING_FREQUENCY_44_1K,
+	XHDMIC_SAMPLING_FREQUENCY_48K,
+	XHDMIC_SAMPLING_FREQUENCY_88_2K,
+	XHDMIC_SAMPLING_FREQUENCY_96K,
+	XHDMIC_SAMPLING_FREQUENCY_176_4K,
+	XHDMIC_SAMPLING_FREQUENCY_192K
+} XHdmiC_SamplingFrequency;
+
+typedef enum {
+	XHDMIC_SAMPLING_FREQ             = 0,
+	XHDMIC_SAMPLING_FREQ_32K         = 32000,
+	XHDMIC_SAMPLING_FREQ_64K         = 32000,
+	XHDMIC_SAMPLING_FREQ_128K        = 128000,
+	XHDMIC_SAMPLING_FREQ_256K        = 128000,
+	XHDMIC_SAMPLING_FREQ_512K        = 128000,
+	XHDMIC_SAMPLING_FREQ_1024K       = 1024000,
+
+	XHDMIC_SAMPLING_FREQ_44_1K       = 44100,
+	XHDMIC_SAMPLING_FREQ_88_2K       = 88200,
+	XHDMIC_SAMPLING_FREQ_176_4K      = 176400,
+	XHDMIC_SAMPLING_FREQ_352_8K      = 352800,
+	XHDMIC_SAMPLING_FREQ_705_6K      = 705600,
+	XHDMIC_SAMPLING_FREQ_1411_2K     = 1411200,
+
+	XHDMIC_SAMPLING_FREQ_48K         = 48000,
+	XHDMIC_SAMPLING_FREQ_96K         = 96000,
+	XHDMIC_SAMPLING_FREQ_192K        = 192000,
+	XHDMIC_SAMPLING_FREQ_384K        = 384000,
+	XHDMIC_SAMPLING_FREQ_768K        = 768000,
+	XHDMIC_SAMPLING_FREQ_1536K       = 1536000,
+} XHdmiC_SamplingFrequencyVal;
+
+typedef enum {
+	XHDMIC_SAMPLE_SIZE,
+	XHDMIC_SAMPLE_SIZE_16,
+	XHDMIC_SAMPLE_SIZE_20,
+	XHDMIC_SAMPLE_SIZE_24
+} XHdmiC_SampleSize;
+
+typedef enum {
+	XHDMIC_AUDIO_CODING_TYPE,
+	XHDMIC_AUDIO_CODING_TYPE_PCM,
+	XHDMIC_AUDIO_CODING_TYPE_AC3,
+	XHDMIC_AUDIO_CODING_TYPE_MPEG1,
+	XHDMIC_AUDIO_CODING_TYPE_MP3,
+	XHDMIC_AUDIO_CODING_TYPE_MPEG2,
+	XHDMIC_AUDIO_CODING_TYPE_AAC,
+	XHDMIC_AUDIO_CODING_TYPE_DTS,
+	XHDMIC_AUDIO_CODING_TYPE_ATRAC,
+	XHDMIC_AUDIO_CODING_TYPE_ONE_BIT_AUDIO,
+	XHDMIC_AUDIO_CODING_TYPE_DOLBY_DIGITAL_PLUS,
+	XHDMIC_AUDIO_CODING_TYPE_DTS_HD,
+	XHDMIC_AUDIO_CODING_TYPE_MAT,
+	XHDMIC_AUDIO_CODING_TYPE_DST,
+	XHDMIC_AUDIO_CODING_TYPE_WMA_PRO
+} XHdmiC_AudioCodingType;
+
+typedef enum {
+	XHDMIC_AUDIO_CHANNEL_COUNT,
+	XHDMIC_AUDIO_CHANNEL_COUNT_2,
+	XHDMIC_AUDIO_CHANNEL_COUNT_3,
+	XHDMIC_AUDIO_CHANNEL_COUNT_4,
+	XHDMIC_AUDIO_CHANNEL_COUNT_5,
+	XHDMIC_AUDIO_CHANNEL_COUNT_6,
+	XHDMIC_AUDIO_CHANNEL_COUNT_7,
+	XHDMIC_AUDIO_CHANNEL_COUNT_8
+} XHdmiC_AudioChannelCount;
+
+typedef enum {
+	XHDMIC_LFEPBL,
+	XHDMIC_LFEPBL_0,
+	XHDMIC_LFEPBL_10,
+} XHdmiC_LFEPlaybackLevel;
+
+typedef enum {
+	XHDMIC_LSV_0,
+	XHDMIC_LSV_1,
+	XHDMIC_LSV_2,
+	XHDMIC_LSV_3,
+	XHDMIC_LSV_4,
+	XHDMIC_LSV_5,
+	XHDMIC_LSV_6,
+	XHDMIC_LSV_7,
+	XHDMIC_LSV_8,
+	XHDMIC_LSV_9,
+	XHDMIC_LSV_10,
+	XHDMIC_LSV_11,
+	XHDMIC_LSV_12,
+	XHDMIC_LSV_13,
+	XHDMIC_LSV_14,
+	XHDMIC_LSV_15
+} XHdmiC_LevelShiftValue;
+
+/**
+* FRL Character Rate Enumeration
+*/
+typedef enum {
+	R_166_667 = 0,	/*  3 Gbps */
+	R_333_333,		/*  6 Gbps */
+	R_444_444,		/*  8 Gbps */
+	R_555_556,		/* 10 Gbps */
+	R_666_667,		/* 12 Gbps */
+	XHDMIC_FRLCHARRATE_SIZE,
+} XHdmiC_FRLCharRate;
+
+/**
+* FRL Rate Enumeration
+*/
+typedef enum {
+	XHDMIC_MAXFRLRATE_NOT_SUPPORTED,
+	XHDMIC_MAXFRLRATE_3X3GBITSPS,
+	XHDMIC_MAXFRLRATE_3X6GBITSPS,
+	XHDMIC_MAXFRLRATE_4X6GBITSPS,
+	XHDMIC_MAXFRLRATE_4X8GBITSPS,
+	XHDMIC_MAXFRLRATE_4X10GBITSPS,
+	XHDMIC_MAXFRLRATE_4X12GBITSPS,
+	XHDMIC_MAXFRLRATE_SIZE,
+	XHDMIC_MAXFRLRATE_TMDSONLY = XHDMIC_MAXFRLRATE_NOT_SUPPORTED
+} XHdmiC_MaxFrlRate;
+
+/**
+* FRL CTS/N Value Table
+*/
+typedef struct {
+	u32 ACR_CTSVal;
+	u32 ACR_NVal[6];	/* multiply of 6 of the initial Sample Freq */
+} XHdmiC_FRL_CTS_N_Val;
+
+/**
+* TMDS Char/N Value Table
+*/
+typedef struct {
+  u32 TMDSCharRate;
+  u32 ACR_NVal[7];
+} XHdmiC_TMDS_N_Table;
+
+/**
+* This typedef contains translations of FRL_Rate to Lanes and Line Rates.
+*/
+typedef struct {
+	u8 Lanes;		/**< No of Lanes */
+	u8 LineRate;		/**< Line Rate */
+} XHdmiC_FrlRate;
+
+typedef enum {
+	XHDMIC_SPD_UNKNOWN = 0x0,
+	XHDMIC_SPD_DIGITAL_STB,
+	XHDMIC_SPD_DVD_PLAYER,
+	XHDMIC_SPD_DVHS,
+	XHDMIC_SPD_HDD_VIDEORECORDER,
+	XHDMIC_SPD_DVC,
+	XHDMIC_SPD_DSC,
+	XHDMIC_SPD_VIDEOCD,
+	XHDMIC_SPD_GAME,
+	XHDMIC_SPD_PC_GENERAL,
+	XHDMIC_SPD_BLURAY_DISC,
+	XHDMIC_SPD_SUPER_AUDIO_CD,
+	XHDMIC_SPD_HD_DVD,
+	XHDMIC_SPD_PMP
+} XHdmiC_SPD_SourceInfo;
+
+typedef enum {
+	XHDMIC_DRM_TRADITIONAL_GAMMA_SDR = 0x0,
+	XHDMIC_DRM_TRADITIONAL_GAMMA_HDR,
+	XHDMIC_DRM_SMPTE_ST_2084,
+	XHDMIC_DRM_HLG
+} XHdmiC_DRM_EOTF;
+
+typedef enum {
+	XHDMIC_DRM_STATIC_METADATA_TYPE1 = 0
+} XHdmiC_DRM_Static_Metadata_Descp_Id;
+
+/**
+ * This typedef contains the data structure for
+ * Auxiliary Video Information Info frame
+ */
+typedef struct XHDMIC_AVI_InfoFrame {
+	unsigned char Version;
+	XHdmiC_Colorspace ColorSpace;
+	u8 ActiveFormatDataPresent;
+	XHdmiC_BarInfo BarInfo;
+	XHdmiC_ScanInfo ScanInfo;
+	XHdmiC_Colorimetry Colorimetry;
+	XHdmiC_PicAspectRatio PicAspectRatio;
+	XHdmiC_ActiveAspectRatio ActiveAspectRatio;
+	unsigned char Itc;
+	XHdmiC_ExtendedColorimetry ExtendedColorimetry;
+	XHdmiC_RGBQuantizationRange QuantizationRange;
+	XHdmiC_NonUniformPictureScaling NonUniformPictureScaling;
+	unsigned char VIC;
+	XHdmiC_YccQuantizationRange YccQuantizationRange;
+	XHdmiC_ContentType ContentType;
+	XHdmiC_PixelRepetitionFactor PixelRepetition;
+	u16 TopBar;
+	u16 BottomBar;
+	u16 LeftBar;
+	u16 RightBar;
+} XHdmiC_AVI_InfoFrame;
+
+/**
+ * This typedef contains the data structure for General Control Packet
+ */
+typedef struct XHdmiC_GCP_Packet {
+	unsigned char Set_AVMUTE;
+	unsigned char Clear_AVMUTE;
+	XHdmiC_ColorDepth ColorDepth;
+	XHdmiC_PixelPackingPhase PixelPackingPhase;
+	unsigned char Default_Phase;
+} XHdmiC_GeneralControlPacket;
+
+/**
+ * This typedef contains the data structure for Audio Infoframe
+ */
+typedef struct XHdmiC_Audio_InfoFrame {
+	unsigned char Version;
+	XHdmiC_AudioChannelCount ChannelCount;
+	XHdmiC_AudioCodingType CodingType;
+	XHdmiC_SampleSize SampleSize;
+	XHdmiC_SamplingFrequency SampleFrequency;
+	u8 CodingTypeExt;
+	u8 ChannelAllocation;
+	XHdmiC_LFEPlaybackLevel LFE_Playback_Level;
+	XHdmiC_LevelShiftValue LevelShiftVal;
+	unsigned char Downmix_Inhibit;
+} XHdmiC_AudioInfoFrame;
+
+/**
+ * This typedef contains the data structure for Audio Metadata Infoframe
+ */
+typedef struct XHdmiC_Audio_Metadata_Packet {
+	u8 Audio3D;
+	u8 Num_Audio_Str;
+	u8 Num_Views;
+	u8 Audio3D_ChannelCount; /* 5 bits */
+	u8 ACAT; /* 4 bits - Audio Channel Allication Standard */
+	u8 Audio3D_ChannelAllocation; /* 8 bits */
+} XHdmiC_AudioMetadata;
+
+/**
+ * This typedef contains the data structure for Source Product Descriptor
+ * Infoframe
+ */
+typedef struct XHdmiC_SPD_InfoFrame {
+	unsigned char Version;
+	unsigned char VN1;
+	unsigned char VN2;
+	unsigned char VN3;
+	unsigned char VN4;
+	unsigned char VN5;
+	unsigned char VN6;
+	unsigned char VN7;
+	unsigned char VN8;
+	unsigned char PD1;
+	unsigned char PD2;
+	unsigned char PD3;
+	unsigned char PD4;
+	unsigned char PD5;
+	unsigned char PD6;
+	unsigned char PD7;
+	unsigned char PD8;
+	unsigned char PD9;
+	unsigned char PD10;
+	unsigned char PD11;
+	unsigned char PD12;
+	unsigned char PD13;
+	unsigned char PD14;
+	unsigned char PD15;
+	unsigned char PD16;
+	XHdmiC_SPD_SourceInfo SourceInfo;
+} XHdmiC_SPDInfoFrame;
+
+/**
+* This typedef contains Video Timing Extended Metadata
+* specific data structure.
+*/
+typedef struct {
+	u8	VRREnabled;
+	u8 	MConstEnabled;
+	u8	FVAFactorMinus1;
+	u8	BaseVFront;
+	u16	BaseRefreshRate;
+	u8	RBEnabled;
+} XV_HdmiC_VideoTimingExtMeta;
+
+typedef struct {
+	u8	Version;
+	u8	FreeSyncSupported;
+	u8	FreeSyncEnabled;
+	u8	FreeSyncActive;
+	u8	FreeSyncMinRefreshRate;
+	u8	FreeSyncMaxRefreshRate;
+} XV_HdmiC_FreeSync;
+
+typedef struct {
+	XV_HdmiC_FreeSync FreeSync;
+	u8	NativeColorSpaceActive;
+	u8	BrightnessControlActive;
+	u8	LocalDimControlActive;
+	u8	sRGBEOTFActive;
+	u8	BT709EOTFActive;
+	u8	Gamma22EOTFActive;
+	u8	Gamma26EOTFActive;
+	u8	PQEOTFActive;
+	u8	BrightnessControl;
+} XV_HdmiC_FreeSyncPro;
+
+/**
+* This typedef contains AMD Source Product Descriptor Infoframe
+* specific data structure.
+*/
+typedef union {
+	XV_HdmiC_FreeSync FreeSync;
+	XV_HdmiC_FreeSyncPro FreeSyncPro;
+} XV_HdmiC_SrcProdDescIF;
+
+typedef enum {
+	XV_HDMIC_VRRINFO_TYPE_NONE,
+	XV_HDMIC_VRRINFO_TYPE_VTEM,
+	XV_HDMIC_VRRINFO_TYPE_SPDIF,
+} XV_HdmiC_VrrInfoframeType;
+
+typedef struct {
+	XV_HdmiC_VrrInfoframeType VrrIfType;
+	union {
+		XV_HdmiC_VideoTimingExtMeta VidTimingExtMeta;
+		XV_HdmiC_SrcProdDescIF SrcProdDescIF;
+	};
+} XV_HdmiC_VrrInfoFrame;
+
+/*************************** Variable Declarations ****************************/
+extern const XHdmiC_VicTable VicTable[VICTABLE_SIZE];
+extern const XHdmiC_FrlRate FrlRateTable[];
+
+/************************** Function Prototypes ******************************/
+
+void XV_HdmiC_ParseAVIInfoFrame(XHdmiC_Aux *AuxPtr,
+			XHdmiC_AVI_InfoFrame *infoFramePtr);
+void XV_HdmiC_ParseGCP(XHdmiC_Aux *AuxPtr,
+			XHdmiC_GeneralControlPacket *GcpPtr);
+void XV_HdmiC_ParseAudioInfoFrame(XHdmiC_Aux *AuxPtr,
+			XHdmiC_AudioInfoFrame *AudIFPtr);
+void XV_HdmiC_ParseDRMIF(XHdmiC_Aux *AuxPtr,
+			struct v4l2_hdr10_payload *DRMInfoFrame);
+XHdmiC_Aux XV_HdmiC_AVIIF_GeneratePacket(XHdmiC_AVI_InfoFrame *infoFramePtr);
+XHdmiC_Aux
+	XV_HdmiC_AudioIF_GeneratePacket(XHdmiC_AudioInfoFrame *AudioInfoFrame);
+XHdmiC_Colorspace
+		XV_HdmiC_XVidC_To_IfColorformat(XVidC_ColorFormat ColorFormat);
+XHdmiC_Aux XV_HdmiC_AudioMetadata_GeneratePacket(XHdmiC_AudioMetadata
+		*AudMetadata);
+XHdmiC_Aux XV_HdmiC_SPDIF_GeneratePacket(XHdmiC_SPDInfoFrame *SPDInfoFrame);
+void XV_HdmiC_DRMIF_GeneratePacket(struct v4l2_hdr10_payload *DRMInfoFrame,
+					XHdmiC_Aux *aux);
+XVidC_AspectRatio XV_HdmiC_IFAspectRatio_To_XVidC(XHdmiC_PicAspectRatio AR);
+
+u32 XHdmiC_FRL_GetNVal(XHdmiC_FRLCharRate FRLCharRate,
+		XHdmiC_SamplingFrequencyVal AudSampleFreqVal);
+u32 XHdmiC_TMDS_GetNVal(u32 TMDSCharRate,
+		XHdmiC_SamplingFrequency AudSampleFreq);
+XHdmiC_SamplingFrequencyVal
+	XHdmiC_FRL_GetAudSampFreq(XHdmiC_FRLCharRate FRLCharRate,
+		u32 CTS, u32 N);
+XHdmiC_SamplingFrequency XHdmiC_TMDS_GetAudSampFreq(u32 TMDSCharRate,
+		u32 N, u32 CTSVal);
+XHdmiC_SamplingFrequency
+	XHdmiC_GetAudIFSampFreq (XHdmiC_SamplingFrequencyVal AudSampFreqVal);
+XHdmiC_SamplingFrequencyVal
+	XHdmiC_GetAudSampFreqVal(XHdmiC_SamplingFrequency AudSampFreqVal);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XHDMIC_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic_vsif.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic_vsif.c
@@ -0,0 +1,699 @@
+/*******************************************************************************
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdmic_vsif.c
+*
+* Contains function definitions related to Vendor Specific InfoFrames used
+* in HDMI. Please see xhdmic_vsif.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  yh     15/01/15 Initial release for 3D video support
+* 1.01  YH  2017/07/19   Clean up Print Statement line ending to "\r\n"
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include <linux/string.h>
+#include "xv_hdmic_vsif.h"
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/**************************** Type Definitions *******************************/
+
+/*************************** Function Prototypes *****************************/
+static int XV_HdmiC_VSIF_Extract3DInfo(u8 *VSIFRaw, XHdmiC_3D_Info *InstancePtr);
+static XHdmiC_3D_Struct_Field XV_HdmiC_VSIF_Conv3DInfoTo3DStruct(XVidC_3DInfo *InfoPtr);
+static XHdmiC_3D_Sampling_Method XV_HdmiC_VSIF_Conv3DInfoTo3DSampMethod(XVidC_3DInfo *InfoPtr);
+static XHdmiC_3D_Sampling_Position XV_HdmiC_VSIF_Conv3DInfoTo3DSampPos(XVidC_3DInfo *InfoPtr);
+static XVidC_3DFormat XV_HdmiC_VSIF_Conv3DStructTo3DFormat(XHdmiC_3D_Struct_Field Value);
+static XVidC_3DSamplingMethod XV_HdmiC_VSIF_Conv3DSampMethodTo3DSampMethod(XHdmiC_3D_Sampling_Method Value);
+static XVidC_3DSamplingPosition XV_HdmiC_VSIF_Conv3DSampPosTo3DSampPos(XHdmiC_3D_Sampling_Position Value);
+
+/************************** Variable Definitions *****************************/
+
+/*************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function extracts the 3D format from XVidC_3DInfo
+* and returns a XV_HdmiC_3D_Struct_Field type.
+*
+* @param InfoPtr is a pointer to the XVidC_3DInfo instance.
+*
+* @return The extracted value.
+*
+******************************************************************************/
+static XHdmiC_3D_Struct_Field XV_HdmiC_VSIF_Conv3DInfoTo3DStruct(XVidC_3DInfo *InfoPtr)
+{
+    switch(InfoPtr->Format) {
+        case XVIDC_3D_FRAME_PACKING :
+            return XHDMIC_3D_STRUCT_FRAME_PACKING;
+            break;
+
+        case XVIDC_3D_FIELD_ALTERNATIVE :
+            return XHDMIC_3D_STRUCT_FIELD_ALTERNATIVE;
+            break;
+
+        case XVIDC_3D_LINE_ALTERNATIVE :
+            return XHDMIC_3D_STRUCT_LINE_ALTERNATIVE;
+            break;
+
+        case XVIDC_3D_SIDE_BY_SIDE_FULL :
+            return XHDMIC_3D_STRUCT_SIDE_BY_SIDE_FULL;
+            break;
+
+        case XVIDC_3D_TOP_AND_BOTTOM_HALF :
+            return XHDMIC_3D_STRUCT_TOP_AND_BOTTOM;
+            break;
+
+        case XVIDC_3D_SIDE_BY_SIDE_HALF :
+            return XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF;
+            break;
+
+        default :
+            return XHDMIC_3D_STRUCT_UNKNOWN;
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function extracts the sampling method info from XVidC_3DInfo
+* and returns a XV_HdmiC_3D_Sampling_Method type.
+*
+* @param InfoPtr is a pointer to the XVidC_3DInfo instance.
+*
+* @return The extracted value.
+*
+******************************************************************************/
+static XHdmiC_3D_Sampling_Method XV_HdmiC_VSIF_Conv3DInfoTo3DSampMethod(XVidC_3DInfo *InfoPtr)
+{
+    switch(InfoPtr->Sampling.Method) {
+        case XVIDC_3D_SAMPLING_HORIZONTAL :
+            return XHDMIC_3D_SAMPLING_HORIZONTAL;
+            break;
+
+        case XVIDC_3D_SAMPLING_QUINCUNX :
+            return XHDMIC_3D_SAMPLING_QUINCUNX;
+            break;
+
+        default :
+            return XHDMIC_3D_SAMPLING_UNKNOWN;
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function extracts the sampling position info from XVidC_3DInfo
+* and returns a XV_HdmiC_3D_Sampling_Position type.
+*
+* @param InfoPtr is a pointer to the XVidC_3DInfo instance.
+*
+* @return The extracted value.
+*
+******************************************************************************/
+static XHdmiC_3D_Sampling_Position XV_HdmiC_VSIF_Conv3DInfoTo3DSampPos(XVidC_3DInfo *InfoPtr)
+{
+    switch(InfoPtr->Sampling.Position) {
+        case XVIDC_3D_SAMPPOS_OLOR :
+            return XHDMIC_3D_SAMPPOS_OLOR;
+            break;
+
+        case XVIDC_3D_SAMPPOS_OLER :
+            return XHDMIC_3D_SAMPPOS_OLER;
+            break;
+
+        case XVIDC_3D_SAMPPOS_ELOR :
+            return XHDMIC_3D_SAMPPOS_ELOR;
+            break;
+
+        case XVIDC_3D_SAMPPOS_ELER :
+            return XHDMIC_3D_SAMPPOS_ELER;
+            break;
+
+        default :
+            return XHDMIC_3D_SAMPPOS_UNKNOWN;
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts a XV_HdmiC_3D_Struct_Field type
+* to a XVidC_3DFormat type.
+*
+* @param Value is the value to convert.
+*
+* @return The converted value.
+*
+******************************************************************************/
+static XVidC_3DFormat XV_HdmiC_VSIF_Conv3DStructTo3DFormat(XHdmiC_3D_Struct_Field Value)
+{
+    switch(Value) {
+        case XHDMIC_3D_STRUCT_FRAME_PACKING :
+            return XVIDC_3D_FRAME_PACKING;
+            break;
+
+        case XHDMIC_3D_STRUCT_FIELD_ALTERNATIVE :
+            return XVIDC_3D_FIELD_ALTERNATIVE;
+            break;
+
+        case XHDMIC_3D_STRUCT_LINE_ALTERNATIVE :
+            return XVIDC_3D_LINE_ALTERNATIVE;
+            break;
+
+        case XHDMIC_3D_STRUCT_SIDE_BY_SIDE_FULL :
+            return XVIDC_3D_SIDE_BY_SIDE_FULL;
+            break;
+
+        case XHDMIC_3D_STRUCT_TOP_AND_BOTTOM :
+            return XVIDC_3D_TOP_AND_BOTTOM_HALF;
+            break;
+
+        case XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF :
+            return XVIDC_3D_SIDE_BY_SIDE_HALF;
+            break;
+
+        default :
+            return XVIDC_3D_UNKNOWN;
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts a XV_HdmiC_3D_Sampling_Method type
+* to a XVidC_3DSamplingMethod type.
+*
+* @param Value is the value to convert.
+*
+* @return The converted value.
+*
+******************************************************************************/
+static XVidC_3DSamplingMethod XV_HdmiC_VSIF_Conv3DSampMethodTo3DSampMethod(XHdmiC_3D_Sampling_Method Value)
+{
+    switch(Value) {
+        case XHDMIC_3D_SAMPLING_HORIZONTAL :
+            return XVIDC_3D_SAMPLING_HORIZONTAL;
+            break;
+
+        case XHDMIC_3D_SAMPLING_QUINCUNX :
+            return XVIDC_3D_SAMPLING_QUINCUNX;
+            break;
+
+        default :
+            return XVIDC_3D_SAMPLING_UNKNOWN;
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts a XV_HdmiC_3D_Sampling_Position type
+* to a XVidC_3DSamplingPosition type.
+*
+* @param Value is the value to convert.
+*
+* @return The converted value.
+*
+******************************************************************************/
+static XVidC_3DSamplingPosition XV_HdmiC_VSIF_Conv3DSampPosTo3DSampPos(XHdmiC_3D_Sampling_Position Value)
+{
+    switch(Value) {
+        case XHDMIC_3D_SAMPPOS_OLOR :
+            return XVIDC_3D_SAMPPOS_OLOR;
+            break;
+
+        case XHDMIC_3D_SAMPPOS_OLER :
+            return XVIDC_3D_SAMPPOS_OLER;
+            break;
+
+        case XHDMIC_3D_SAMPPOS_ELOR :
+            return XVIDC_3D_SAMPPOS_ELOR;
+            break;
+
+        case XHDMIC_3D_SAMPPOS_ELER :
+            return XVIDC_3D_SAMPPOS_ELER;
+            break;
+
+        default :
+            return XVIDC_3D_SAMPPOS_UNKNOWN;
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function parses a Vendor Specific InfoFrame (VSIF).
+*
+* @param AuxPtr is a pointer to the XV_HdmiTx_Rx_Aux instance.
+*
+* @param VSIFPtr is a pointer to the XV_HdmiC_VSIF instance.
+*
+* @return
+*  - XST_SUCCESS if operation was successful
+*  - XST_FAILURE if an error was detected during parsing
+*
+******************************************************************************/
+int XV_HdmiC_VSIF_ParsePacket(XHdmiC_Aux *AuxPtr, XHdmiC_VSIF  *VSIFPtr)
+{
+    u8 *pData;
+    u32 temp;
+    int Index;
+    int Status = XST_FAILURE;
+
+    /* Verify arguments */
+    Xil_AssertNonvoid(AuxPtr != NULL);
+    Xil_AssertNonvoid(VSIFPtr != NULL);
+
+    pData = &AuxPtr->Data.Byte[0];
+
+    /* Clear the instance */
+    (void)memset((void *)VSIFPtr, 0, sizeof(XHdmiC_VSIF));
+
+    /* Set packet version */
+    VSIFPtr->Version = AuxPtr->Header.Byte[1];
+
+    /* IEEE Registration Identifier */
+    for (Index = 0; Index < 3; Index++){
+        temp = pData[Index+1];
+        VSIFPtr->IEEE_ID |= (temp << (Index * 8));
+    }
+
+    /*
+     * Check if the IEEE_ID is 0x000C03 as per
+     * Table H1 from HDMI 1.4b spec
+     */
+    if (VSIFPtr->IEEE_ID != 0xC03)
+	    return XST_FAILURE;
+
+    /* HDMI Video Format */
+    temp = (pData[4] & XHDMIC_VSIF_VIDEO_FORMAT_MASK) >> XHDMIC_VSIF_VIDEO_FORMAT_SHIFT;
+    if (temp >= XHDMIC_VSIF_VF_UNKNOWN) {
+        VSIFPtr->Format = XHDMIC_VSIF_VF_UNKNOWN;
+    }
+    else {
+        VSIFPtr->Format = (XHdmiC_VSIF_Video_Format)temp;
+    }
+
+    switch(VSIFPtr->Format) {
+        /* HDMI VIC */
+        case XHDMIC_VSIF_VF_EXTRES :
+            VSIFPtr->HDMI_VIC = pData[5];
+            Status = XST_SUCCESS;
+            break;
+
+        /* 3D Information */
+        case XHDMIC_VSIF_VF_3D :
+            Status = XV_HdmiC_VSIF_Extract3DInfo(pData, &VSIFPtr->Info_3D);
+            break;
+
+        /* No additional information */
+        case XHDMIC_VSIF_VF_NOINFO :
+            Status = XST_SUCCESS;
+            break;
+
+        default :
+
+            break;
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function extracts the 3D information from the
+* Vendor Specific InfoFrame (VSIF).
+*
+* @param VSIFRaw is a pointer to the VSIF payload.
+*
+* @param InstancePtr is a pointer to the XV_HdmiC_3D_Info instance.
+*
+* @return
+*  - XST_SUCCESS if operation was successful
+*  - XST_FAILURE if an error was detected during parsing
+*
+******************************************************************************/
+int XV_HdmiC_VSIF_Extract3DInfo(u8 *VSIFRaw, XHdmiC_3D_Info *InstancePtr)
+{
+    u8 *pData;
+    u8 temp;
+
+    /* Verify arguments */
+    Xil_AssertNonvoid(VSIFRaw != NULL);
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* 3D info starts at byte PB5 */
+    pData = &VSIFRaw[5];
+
+    /* Clear the instance */
+    (void)memset((void *)InstancePtr, 0, sizeof(XHdmiC_3D_Info));
+
+    /* Set default values for the items that are not always set */
+    InstancePtr->Stream.Sampling.Method = XV_HdmiC_VSIF_Conv3DSampMethodTo3DSampMethod(XHDMIC_3D_SAMPLING_UNKNOWN);
+    InstancePtr->Stream.Sampling.Position = XV_HdmiC_VSIF_Conv3DSampPosTo3DSampPos(XHDMIC_3D_SAMPPOS_UNKNOWN);
+
+    /* Detect 3D Metadata presence */
+    if (*pData & XHDMIC_3D_META_PRESENT_MASK)
+        InstancePtr->MetaData.IsPresent = TRUE;
+    else
+        InstancePtr->MetaData.IsPresent = FALSE;
+
+    /* Extract the 3D_Structure */
+    temp = (*pData & XHDMIC_3D_STRUCT_MASK) >> XHDMIC_3D_STRUCT_SHIFT;
+    if (temp >= XHDMIC_3D_STRUCT_UNKNOWN || temp == 7) {
+        InstancePtr->Stream.Format = XV_HdmiC_VSIF_Conv3DStructTo3DFormat(XHDMIC_3D_STRUCT_UNKNOWN);
+    }
+    else {
+        InstancePtr->Stream.Format = XV_HdmiC_VSIF_Conv3DStructTo3DFormat((XHdmiC_3D_Struct_Field)temp);
+    }
+
+    /* Extract the 3D_Ext_Data */
+    if (temp >= XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF) {
+        /* Go to next byte */
+        pData++;
+
+        /* Extract the sampling method */
+        temp = (*pData & XHDMIC_3D_SAMP_METHOD_MASK) >> XHDMIC_3D_SAMP_METHOD_SHIFT;
+        if (temp >= XHDMIC_3D_SAMPLING_UNKNOWN)
+            InstancePtr->Stream.Sampling.Method = XV_HdmiC_VSIF_Conv3DSampMethodTo3DSampMethod(XHDMIC_3D_SAMPLING_UNKNOWN);
+        else
+            InstancePtr->Stream.Sampling.Method = XV_HdmiC_VSIF_Conv3DSampMethodTo3DSampMethod((XHdmiC_3D_Sampling_Method)temp);
+
+        /* Extract the sampling position */
+        temp = (*pData & XHDMIC_3D_SAMP_POS_MASK) >> XHDMIC_3D_SAMP_POS_SHIFT;
+        if (temp >= XHDMIC_3D_SAMPPOS_UNKNOWN)
+            InstancePtr->Stream.Sampling.Position = XV_HdmiC_VSIF_Conv3DSampPosTo3DSampPos(XHDMIC_3D_SAMPPOS_UNKNOWN);
+        else
+            InstancePtr->Stream.Sampling.Position = XV_HdmiC_VSIF_Conv3DSampPosTo3DSampPos((XHdmiC_3D_Sampling_Position)temp);
+    }
+
+    /* Extract the 3D_Metadata */
+    if (InstancePtr->MetaData.IsPresent) {
+        /* Go to next byte */
+        pData++;
+
+        /* Extract the 3D Metadata type */
+        temp = (*pData & XHDMIC_3D_META_TYPE_MASK) >> XHDMIC_3D_META_TYPE_SHIFT;
+        if (temp >= XHDMIC_3D_META_UNKNOWN)
+            InstancePtr->MetaData.Type = XHDMIC_3D_META_UNKNOWN;
+        else
+            InstancePtr->MetaData.Type = (XHdmiC_3D_MetaData_Type)temp;
+
+        /* Extract the 3D Metadata length */
+        InstancePtr->MetaData.Length = (*pData & XHDMIC_3D_META_LENGTH_MASK) >> XHDMIC_3D_META_LENGTH_SHIFT;
+
+        /* Extract the 3D Metadata */
+        int i;
+        for (i = 0; i<InstancePtr->MetaData.Length; i++){
+            if (i < XHDMIC_3D_META_MAX_SIZE)
+                InstancePtr->MetaData.Data[i] = *(++pData);
+            else
+                return XST_FAILURE;
+        }
+    }
+
+    return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function generates a Vendor Specific InfoFrame (VSIF).
+*
+* @param VSIFPtr is a pointer to the XV_HdmiC_VSIF instance.
+*
+* @param AuxPtr is a pointer to the XV_HdmiTx_Tx_Aux instance.
+*
+* @return
+*  - XST_SUCCESS if operation was successful
+*  - XST_FAILURE if an error was detected during generation
+*
+******************************************************************************/
+XHdmiC_Aux XV_HdmiC_VSIF_GeneratePacket(XHdmiC_VSIF  *VSIFPtr)
+{
+    u8 Index = 0;
+    u8 ByteCount = 0;
+    u8 Crc = 0;
+    XHdmiC_Aux Aux;
+
+    (void)memset((void *)&Aux, 0, sizeof(XHdmiC_Aux));
+
+    XHdmiC_3D_Struct_Field Format;
+    XHdmiC_3D_Sampling_Method SampMethod;
+    XHdmiC_3D_Sampling_Position SampPos;
+
+    /* Header, Packet type*/
+    Aux.Header.Byte[0] = AUX_VSIF_TYPE;
+
+    /* Version */
+    Aux.Header.Byte[1] = VSIFPtr->Version;
+
+    /* Checksum (this will be calculated by the HDMI TX IP) */
+    Aux.Header.Byte[3] = 0;
+
+    /* Data */
+
+    /* IEEE Registration ID */
+    Aux.Data.Byte[++ByteCount] = VSIFPtr->IEEE_ID;
+    Aux.Data.Byte[++ByteCount] = VSIFPtr->IEEE_ID >> 8;
+    Aux.Data.Byte[++ByteCount] = VSIFPtr->IEEE_ID >> 16;
+
+    Aux.Data.Byte[++ByteCount] = (VSIFPtr->Format << XHDMIC_VSIF_VIDEO_FORMAT_SHIFT) & XHDMIC_VSIF_VIDEO_FORMAT_MASK;
+
+    switch (VSIFPtr->Format) {
+        /* Extended resolution format present */
+        case XHDMIC_VSIF_VF_EXTRES :
+            /* HDMI_VIC */
+            Aux.Data.Byte[++ByteCount] = VSIFPtr->HDMI_VIC;
+            break;
+
+        /* 3D format indication present */
+        case XHDMIC_VSIF_VF_3D :
+            /* 3D_Structure */
+            Format = XV_HdmiC_VSIF_Conv3DInfoTo3DStruct(&VSIFPtr->Info_3D.Stream);
+            Aux.Data.Byte[++ByteCount] = (Format << XHDMIC_3D_STRUCT_SHIFT) & XHDMIC_3D_STRUCT_MASK;
+
+            /* 3D_Meta_present*/
+            Aux.Data.Byte[ByteCount] |= (VSIFPtr->Info_3D.MetaData.IsPresent << XHDMIC_3D_META_PRESENT_SHIFT) & XHDMIC_3D_META_PRESENT_MASK;
+
+            /* 3D_Ext_Data */
+            if (Format >= XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF) {
+                SampMethod = XV_HdmiC_VSIF_Conv3DInfoTo3DSampMethod(&VSIFPtr->Info_3D.Stream);
+                Aux.Data.Byte[++ByteCount] = (SampMethod << XHDMIC_3D_SAMP_METHOD_SHIFT) & XHDMIC_3D_SAMP_METHOD_MASK;
+                SampPos = XV_HdmiC_VSIF_Conv3DInfoTo3DSampPos(&VSIFPtr->Info_3D.Stream);
+                Aux.Data.Byte[ByteCount] |= (SampPos << XHDMIC_3D_SAMP_POS_SHIFT) & XHDMIC_3D_SAMP_POS_MASK;
+            }
+
+            /* 3D Metadata */
+            if (VSIFPtr->Info_3D.MetaData.IsPresent) {
+                /* 3D_Metadata_type */
+                Aux.Data.Byte[++ByteCount] = (VSIFPtr->Info_3D.MetaData.Type << XHDMIC_3D_META_TYPE_SHIFT) & XHDMIC_3D_META_TYPE_MASK;
+                /* 3D_Metadata_length */
+                Aux.Data.Byte[ByteCount] |= (VSIFPtr->Info_3D.MetaData.Length << XHDMIC_3D_META_LENGTH_SHIFT) & XHDMIC_3D_META_LENGTH_MASK;
+
+                /* 3D_Metadata */
+                for (Index = 0; Index < VSIFPtr->Info_3D.MetaData.Length; Index++) {
+                    Aux.Data.Byte[++ByteCount] = VSIFPtr->Info_3D.MetaData.Data[Index];
+                }
+            }
+
+            break;
+
+        default :
+            break;
+    }
+
+    /* Set the payload length */
+    Aux.Header.Byte[2] = ByteCount;
+
+    /* Calculate checksum */
+    /* Header */
+    for (Index = 0; Index < 3; Index++) {
+        Crc += Aux.Header.Byte[Index];
+    }
+
+    /* Data */
+    for (Index = 1; Index <= ByteCount; Index++) {
+        Crc += Aux.Data.Byte[Index];
+    }
+
+    /* Set the checksum */
+    Aux.Data.Byte[0] = 256 - Crc;
+
+    return Aux;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function displays the contents of an XV_HdmiC_VSIF instance.
+*
+* @param VSIFPtr is a pointer to the XV_HdmiC_VSIF instance.
+*
+* @return None.
+*
+******************************************************************************/
+void XV_HdmiC_VSIF_DisplayInfo(XHdmiC_VSIF  *VSIFPtr)
+{
+    switch (VSIFPtr->Format) {
+        /* Extended resolution format present */
+        case XHDMIC_VSIF_VF_EXTRES :
+            /* HDMI_VIC */
+            xil_printf("HDMI_VIC : %d\r\n", VSIFPtr->HDMI_VIC);
+            break;
+
+        /* 3D format indication present */
+        case XHDMIC_VSIF_VF_3D :
+            /* 3D_Structure */
+            xil_printf("3D Format : %s\r\n", XV_HdmiC_VSIF_3DStructToString(XV_HdmiC_VSIF_Conv3DInfoTo3DStruct(&VSIFPtr->Info_3D.Stream)));
+
+            /* 3D_Ext_Data */
+            if (XV_HdmiC_VSIF_Conv3DInfoTo3DStruct(&VSIFPtr->Info_3D.Stream) >= XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF) {
+                xil_printf("Sampling Method : %s\r\n", XV_HdmiC_VSIF_3DSampMethodToString(XV_HdmiC_VSIF_Conv3DInfoTo3DSampMethod(&VSIFPtr->Info_3D.Stream)));
+                xil_printf("Sampling Position : %s\r\n", XV_HdmiC_VSIF_3DSampPosToString(XV_HdmiC_VSIF_Conv3DInfoTo3DSampPos(&VSIFPtr->Info_3D.Stream)));
+            }
+
+            /* 3D Metadata */
+            if (VSIFPtr->Info_3D.MetaData.IsPresent) {
+                /* 3D_Metadata_type */
+
+                /* 3D_Metadata */
+            }
+
+            break;
+
+        default :
+            break;
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a string representation of the
+* enumerated type XV_HdmiC_3D_Struct_Field.
+*
+* @param Item specifies the value to convert.
+*
+* @return Pointer to the converted string.
+*
+******************************************************************************/
+char* XV_HdmiC_VSIF_3DStructToString(XHdmiC_3D_Struct_Field Item)
+{
+    switch(Item) {
+        case XHDMIC_3D_STRUCT_FRAME_PACKING :
+            return (char*) "Frame Packing";
+
+        case XHDMIC_3D_STRUCT_FIELD_ALTERNATIVE :
+            return (char*) "Field Alternative";
+
+        case XHDMIC_3D_STRUCT_LINE_ALTERNATIVE :
+            return (char*) "Line Alternative";
+
+        case XHDMIC_3D_STRUCT_SIDE_BY_SIDE_FULL :
+            return (char*) "Side-by-Side(Full)";
+
+        case XHDMIC_3D_STRUCT_L_DEPTH :
+            return (char*) "L + Depth";
+
+        case XHDMIC_3D_STRUCT_L_DEPTH_GRAPH_GDEPTH :
+            return (char*) "L + Depth + Graphics + Graphics-depth";
+
+        case XHDMIC_3D_STRUCT_TOP_AND_BOTTOM :
+            return (char*) "Top-and-Bottom";
+
+        case XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF :
+            return (char*) "Side-by-Side(Half)";
+
+        default :
+            return (char*) "Unknown";
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a string representation of the
+* enumerated type XV_HdmiC_3D_Sampling_Method.
+*
+* @param Item specifies the value to convert.
+*
+* @return Pointer to the converted string.
+*
+******************************************************************************/
+char* XV_HdmiC_VSIF_3DSampMethodToString(XHdmiC_3D_Sampling_Method Item)
+{
+    switch(Item) {
+        case XHDMIC_3D_SAMPLING_HORIZONTAL :
+            return (char*) "Horizontal Sub-Sampling";
+
+        case XHDMIC_3D_SAMPLING_QUINCUNX :
+            return (char*) "Quincunx Matrix";
+
+        default :
+            return (char*) "Unknown";
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns a string representation of the
+* enumerated type XV_HdmiC_3D_Sampling_Position.
+*
+* @param Item specifies the value to convert.
+*
+* @return Pointer to the converted string.
+*
+******************************************************************************/
+char* XV_HdmiC_VSIF_3DSampPosToString(XHdmiC_3D_Sampling_Position Item)
+{
+    switch(Item) {
+        case XHDMIC_3D_SAMPPOS_OLOR :
+            return (char*) "Odd/Left, Odd/Right";
+
+        case XHDMIC_3D_SAMPPOS_OLER :
+            return (char*) "Odd/Left, Even/Right";
+
+        case XHDMIC_3D_SAMPPOS_ELOR :
+            return (char*) "Even/Left, Odd/Right";
+
+        case XHDMIC_3D_SAMPPOS_ELER :
+            return (char*) "Even/Left, Even/Right";
+
+        default :
+            return (char*) "Unknown";
+    }
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic_vsif.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xv_hdmic_vsif.h
@@ -0,0 +1,184 @@
+/******************************************************************************
+*
+* Copyright (C) 2018 Xilinx, Inc..
+*
+* This software is licensed under the terms of the GNU General Public
+* License version 2, as published by the Free Software Foundation, and
+* may be copied, distributed, and modified under those terms.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+* GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xhdmic_vsif.h
+*
+* This is the main header file for Vendor Specific InfoFrames used in HDMI.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  yh     15/01/15 Initial release for 3D video support
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XHDMIC_VSIF_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XHDMIC_VSIF_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+#include "xil_types.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xv_hdmic.h"
+#include "xvidc.h"
+
+/************************** Constant Definitions ******************************/
+
+/** @name Vendor Specific InfoFrame Field Masks and Shifts.
+ * @{
+ */
+#define XHDMIC_VSIF_VIDEO_FORMAT_SHIFT 5
+#define XHDMIC_VSIF_VIDEO_FORMAT_MASK (0x7 << XHDMIC_VSIF_VIDEO_FORMAT_SHIFT)
+
+#define XHDMIC_3D_STRUCT_SHIFT 4
+#define XHDMIC_3D_STRUCT_MASK (0xF << XHDMIC_3D_STRUCT_SHIFT)
+
+#define XHDMIC_3D_SAMP_METHOD_SHIFT 6
+#define XHDMIC_3D_SAMP_METHOD_MASK (0x3 << XHDMIC_3D_SAMP_METHOD_SHIFT)
+
+#define XHDMIC_3D_SAMP_POS_SHIFT 4
+#define XHDMIC_3D_SAMP_POS_MASK (0x3 << XHDMIC_3D_SAMP_POS_SHIFT)
+
+#define XHDMIC_3D_META_PRESENT_SHIFT 3
+#define XHDMIC_3D_META_PRESENT_MASK (0x1 << XHDMIC_3D_META_PRESENT_SHIFT)
+
+#define XHDMIC_3D_META_TYPE_SHIFT 5
+#define XHDMIC_3D_META_TYPE_MASK (0x7 << XHDMIC_3D_META_TYPE_SHIFT)
+
+#define XHDMIC_3D_META_LENGTH_SHIFT 0
+#define XHDMIC_3D_META_LENGTH_MASK (0x1F << XHDMIC_3D_META_LENGTH_SHIFT)
+/* @} */
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * HDMI Video Format
+ */
+typedef enum {
+    XHDMIC_VSIF_VF_NOINFO = 0, /**<No additional HDMI video format is presented */
+    XHDMIC_VSIF_VF_EXTRES = 1, /**<Extended resolution format present */
+    XHDMIC_VSIF_VF_3D     = 2, /**<3D format indication present */
+    XHDMIC_VSIF_VF_UNKNOWN
+} XHdmiC_VSIF_Video_Format;
+
+/**
+ * 3D structure definitions as defined in the HDMI 1.4a specification
+ */
+typedef enum {
+    XHDMIC_3D_STRUCT_FRAME_PACKING        = 0, /**<Frame packing */
+    XHDMIC_3D_STRUCT_FIELD_ALTERNATIVE    = 1, /**<Field alternative */
+    XHDMIC_3D_STRUCT_LINE_ALTERNATIVE     = 2, /**<Line alternative */
+    XHDMIC_3D_STRUCT_SIDE_BY_SIDE_FULL    = 3, /**<Side-by-side (full) */
+    XHDMIC_3D_STRUCT_L_DEPTH              = 4, /**<L + depth */
+    XHDMIC_3D_STRUCT_L_DEPTH_GRAPH_GDEPTH = 5, /**<L + depth + graphics + graphics-depth */
+    XHDMIC_3D_STRUCT_TOP_AND_BOTTOM       = 6, /**<Top-and-bottom */
+    // 7 is reserved for future use
+    XHDMIC_3D_STRUCT_SIDE_BY_SIDE_HALF    = 8, /**<Side-by-side (half) */
+    XHDMIC_3D_STRUCT_UNKNOWN
+} XHdmiC_3D_Struct_Field;
+
+/**
+ * Sub-sampling methods for Side-by-side(half)
+ */
+typedef enum {
+    XHDMIC_3D_SAMPLING_HORIZONTAL = 0, /**<Horizontal sub-sampling */
+    XHDMIC_3D_SAMPLING_QUINCUNX   = 1, /**<Quincunx matrix */
+    XHDMIC_3D_SAMPLING_UNKNOWN
+} XHdmiC_3D_Sampling_Method;
+
+/**
+ * Sub-sampling positions for the sub-sampling methods
+ */
+typedef enum {
+    XHDMIC_3D_SAMPPOS_OLOR = 0, /**<Odd/Left, Odd/Right */
+    XHDMIC_3D_SAMPPOS_OLER = 1, /**<Odd/Left, Even/Right */
+    XHDMIC_3D_SAMPPOS_ELOR = 2, /**<Even/Left, Odd/Right */
+    XHDMIC_3D_SAMPPOS_ELER = 3, /**<Even/Left, Even/Right */
+    XHDMIC_3D_SAMPPOS_UNKNOWN
+} XHdmiC_3D_Sampling_Position;
+
+/**
+ * 3D Metadata types
+ */
+typedef enum {
+    XHDMIC_3D_META_PARALLAX = 0, /**<Parallax information */
+    XHDMIC_3D_META_UNKNOWN
+} XHdmiC_3D_MetaData_Type;
+
+
+// 8 is the maximum size for currently defined meta types (HDMI 1.4a)
+#define XHDMIC_3D_META_MAX_SIZE 8 /**<Maximum 3D Metadata size in bytes */
+
+/**
+ * Structure for 3D meta data
+ */
+typedef struct {
+    u8                     IsPresent;                    /**<Indicates 3D metadata presence */
+    XHdmiC_3D_MetaData_Type Type;                         /**<Type */
+    u8                     Length;                       /**<Length in bytes */
+    u8                     Data[XHDMIC_3D_META_MAX_SIZE]; /**<Data */
+} XHdmiC_3D_MetaData;
+
+/**
+ * Structure containing 3D information
+ */
+typedef struct {
+    XVidC_3DInfo               Stream;
+    XHdmiC_3D_MetaData          MetaData;   /**<3D Metadata */
+} XHdmiC_3D_Info;
+
+/**
+ * Structure for holding the VSIF.
+ * Format indicates the used union member.
+ */
+typedef struct {
+    u8                      Version; /**<Version */
+    u32                     IEEE_ID; /**<IEEE Registration Identifier */
+    XHdmiC_VSIF_Video_Format Format;  /**<HDMI Video Format */
+
+    union {
+        u8            HDMI_VIC; /**<XHDMIC_VSIF_VF_EXTRES: HDMI Video Format Identification Code */
+        XHdmiC_3D_Info Info_3D;  /**<XHDMIC_VSIF_VF_3D: 3D Information */
+    };
+} XHdmiC_VSIF;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Prototypes ******************************/
+
+/* Vendor Specific Infomation related functions */
+int XV_HdmiC_VSIF_ParsePacket(XHdmiC_Aux *AuxPtr, XHdmiC_VSIF  *VSIFPtr);
+XHdmiC_Aux XV_HdmiC_VSIF_GeneratePacket(XHdmiC_VSIF  *VSIFPtr);
+
+void XV_HdmiC_VSIF_DisplayInfo(XHdmiC_VSIF  *VSIFPtr);
+char* XV_HdmiC_VSIF_3DStructToString(XHdmiC_3D_Struct_Field Item);
+char* XV_HdmiC_VSIF_3DSampMethodToString(XHdmiC_3D_Sampling_Method Item);
+char* XV_HdmiC_VSIF_3DSampPosToString(XHdmiC_3D_Sampling_Position Item);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* End of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvidc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvidc.c
@@ -0,0 +1,1330 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvidc.c
+ * @{
+ *
+ * Contains common utility functions that are typically used by video-related
+ * drivers and applications.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   rc,  01/10/15 Initial release.
+ *       als
+ * 2.2   als  02/01/16 Functions with pointer arguments that don't modify
+ *                     contents now const.
+ *                     Added ability to insert a custom video timing table.
+ *       yh            Added 3D support.
+ * 3.0   aad  05/13/16 Added API to search for RB video modes.
+ * 3.1   rco  07/26/16 Added extern definition for timing table array
+ *                     Added video-in-memory color formats
+ *                     Updated XVidC_RegisterCustomTimingModes API signature
+ * 4.1   rco  11/23/16 Added new memory formats
+ *                     Added new API to get video mode id that matches exactly
+ *                     with provided timing information
+ *                     Fix c++ warnings
+ * 4.2	 jsr  07/22/17 Added new framerates and color formats to support SDI
+ *                     Reordered YCBCR422 colorforamt and removed other formats
+ *                     that are not needed for SDI which were added earlier.
+ *       vyc  10/04/17 Added new streaming alpha formats and new memory formats
+ * 4.3   eb   26/01/18 Added API XVidC_GetVideoModeIdExtensive
+ *       jsr  02/22/18 Added XVIDC_CSF_YCBCR_420 color space format
+ *       vyc  04/04/18 Added BGR8 memory format
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xvidc.h"
+
+/*************************** Variable Declarations ****************************/
+extern const XVidC_VideoTimingMode XVidC_VideoTimingModes[XVIDC_VM_NUM_SUPPORTED];
+
+const XVidC_VideoTimingMode *XVidC_CustomTimingModes = NULL;
+int XVidC_NumCustomModes = 0;
+
+/**************************** Function Prototypes *****************************/
+
+static const XVidC_VideoTimingMode *XVidC_GetCustomVideoModeData(
+		XVidC_VideoMode VmId);
+static u8 XVidC_IsVtmRb(const char *VideoModeStr, u8 RbN);
+
+/*************************** Function Definitions *****************************/
+
+/******************************************************************************/
+/**
+ * This function registers a user-defined custom video mode timing table with
+ * video_common. Functions which search the available video modes, or take VmId
+ * as an input, will operate on or check the custom video mode timing table in
+ * addition to the pre-defined video mode timing table (XVidC_VideoTimingModes).
+ *
+ * @param	CustomTable is a pointer to the user-defined custom vide mode
+ *		timing table to register.
+ * @param	NumElems is the number of video modes supported by CustomTable.
+ *
+ * @return
+ *		- XST_SUCCESS if the custom table was successfully registered.
+ *		- XST_FAILURE if an existing custom table is already present.
+ *
+ * @note	IDs in the custom table may not conflict with IDs reserved by
+ *		the XVidC_VideoMode enum.
+ *
+*******************************************************************************/
+u32 XVidC_RegisterCustomTimingModes(const XVidC_VideoTimingMode *CustomTable,
+		                            u16 NumElems)
+{
+	u16 Index;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(CustomTable != NULL);
+	for (Index = 0; Index < NumElems; Index++) {
+		Xil_AssertNonvoid((CustomTable[Index].VmId > XVIDC_VM_CUSTOM));
+		/* The IDs of each video mode in the custom table must not
+		 * conflict with IDs reserved by video_common. */
+	}
+
+	/* Fail if a custom table is currently already registered. */
+	if (XVidC_CustomTimingModes) {
+		return XST_FAILURE;
+	}
+
+	XVidC_CustomTimingModes = CustomTable;
+	XVidC_NumCustomModes    = NumElems;
+
+	return XST_SUCCESS;
+}
+
+/******************************************************************************/
+/**
+ * This function unregisters the user-defined custom video mode timing table
+ * previously registered by XVidC_RegisterCustomTimingModes().
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVidC_UnregisterCustomTimingModes(void)
+{
+	XVidC_CustomTimingModes = NULL;
+	XVidC_NumCustomModes    = 0;
+}
+
+/******************************************************************************/
+/**
+ * This function calculates pixel clock based on the inputs.
+ *
+ * @param	HTotal specifies horizontal total.
+ * @param	VTotal specifies vertical total.
+ * @param	FrameRate specifies rate at which frames are generated.
+ *
+ * @return	Pixel clock in Hz.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u64 XVidC_GetPixelClockHzByHVFr(u32 HTotal, u32 VTotal, u8 FrameRate)
+{
+	return (HTotal * VTotal * FrameRate);
+}
+
+/******************************************************************************/
+/**
+ * This function calculates pixel clock from video mode.
+ *
+ * @param	VmId specifies the resolution id.
+ *
+ * @return	Pixel clock in Hz.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u64 XVidC_GetPixelClockHzByVmId(XVidC_VideoMode VmId)
+{
+	u64 ClkHz;
+	const XVidC_VideoTimingMode *VmPtr;
+
+	VmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VmPtr) {
+		return 0;
+	}
+
+	if (XVidC_IsInterlaced(VmId)) {
+		/* For interlaced mode, use both frame 0 and frame 1 vertical
+		 * totals. */
+		ClkHz = VmPtr->Timing.F0PVTotal + VmPtr->Timing.F1VTotal;
+
+		/* Multiply the number of pixels by the frame rate of each
+		 * individual frame (half of the total frame rate). */
+		ClkHz *= VmPtr->FrameRate / 2;
+	}
+	else {
+		/* For progressive mode, use only frame 0 vertical total. */
+		ClkHz = VmPtr->Timing.F0PVTotal;
+
+		/* Multiply the number of pixels by the frame rate. */
+		ClkHz *= VmPtr->FrameRate;
+	}
+
+	/* Multiply the vertical total by the horizontal total for number of
+	 * pixels. */
+	ClkHz *= VmPtr->Timing.HTotal;
+
+	return ClkHz;
+}
+
+/******************************************************************************/
+/**
+ * This function checks if the input video mode is interlaced/progressive based
+ * on its ID from the video timings table.
+ *
+ * @param	VmId specifies the resolution ID from the video timings table.
+ *
+ * @return	Video format.
+ *		- XVIDC_VF_PROGRESSIVE
+ *		- XVIDC_VF_INTERLACED
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+XVidC_VideoFormat XVidC_GetVideoFormat(XVidC_VideoMode VmId)
+{
+	const XVidC_VideoTimingMode *VmPtr;
+
+	VmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VmPtr) {
+		return XVIDC_VF_UNKNOWN;
+	}
+
+	if (VmPtr->Timing.F1VTotal == 0) {
+		return (XVIDC_VF_PROGRESSIVE);
+	}
+
+	return (XVIDC_VF_INTERLACED);
+}
+
+/******************************************************************************/
+/**
+ * This function checks if the input video mode is interlaced based on its ID
+ * from the video timings table.
+ *
+ * @param	VmId specifies the resolution ID from the video timings table.
+ *
+ * @return
+ *		- 1 if the video timing with the supplied table ID is
+ *		  interlaced.
+ *		- 0 if the video timing is progressive.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u8 XVidC_IsInterlaced(XVidC_VideoMode VmId)
+{
+	if (XVidC_GetVideoFormat(VmId) == XVIDC_VF_INTERLACED) {
+		return 1;
+	}
+
+	return 0;
+}
+
+/******************************************************************************/
+/**
+ * This function returns the Video Mode ID that matches the detected input
+ * timing, frame rate and I/P flag
+ *
+ * @param	Timing is the pointer to timing parameters to match
+ * @param	FrameRate specifies refresh rate in HZ
+ * @param	IsInterlaced is flag.
+ *		      - 0 = Progressive
+ *			  - 1 = Interlaced.
+ *
+ * @return	Id of a supported video mode.
+ *
+ * @note	This is an extension of XVidC_GetVideoModeId API to include
+ *          blanking information in match process. No attempt is made to
+ *          search for reduced blanking entries, if any.
+ *
+*******************************************************************************/
+XVidC_VideoMode XVidC_GetVideoModeIdWBlanking(const XVidC_VideoTiming *Timing,
+		                                      u32 FrameRate, u8 IsInterlaced)
+{
+  XVidC_VideoMode VmId;
+  XVidC_VideoTiming const *StdTiming = NULL;
+
+  /* First search for ID with matching Width & Height */
+  VmId = XVidC_GetVideoModeId(Timing->HActive, Timing->VActive, FrameRate,
+		                      IsInterlaced);
+
+  if(VmId == XVIDC_VM_NOT_SUPPORTED) {
+	return(VmId);
+  } else {
+
+	/* Get standard timing info from default timing table */
+	StdTiming = XVidC_GetTimingInfo(VmId);
+
+	/* Match against detected timing parameters */
+	if((Timing->HActive        == StdTiming->HActive) &&
+	   (Timing->VActive        == StdTiming->VActive) &&
+	   (Timing->HTotal         == StdTiming->HTotal) &&
+	   (Timing->F0PVTotal      == StdTiming->F0PVTotal) &&
+	   (Timing->HFrontPorch    == StdTiming->HFrontPorch) &&
+	   (Timing->HSyncWidth     == StdTiming->HSyncWidth) &&
+	   (Timing->HBackPorch     == StdTiming->HBackPorch) &&
+	   (Timing->F0PVFrontPorch == StdTiming->F0PVFrontPorch) &&
+	   (Timing->F0PVSyncWidth  == StdTiming->F0PVSyncWidth) &&
+	   (Timing->F0PVBackPorch  == StdTiming->F0PVBackPorch)) {
+       return(VmId);
+	 } else {
+	   return(XVIDC_VM_NOT_SUPPORTED);
+	 }
+  }
+}
+
+/******************************************************************************/
+/**
+ * This function returns the Video Mode ID that matches the detected input
+ * width, height, frame rate and I/P flag
+ *
+ * @param	Width specifies the number pixels per scanline.
+ * @param	Height specifies the number of scanline's.
+ * @param	FrameRate specifies refresh rate in HZ
+ * @param	IsInterlaced is flag.
+ *		- 0 = Progressive
+ *		- 1 = Interlaced.
+ *
+ * @return	Id of a supported video mode.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+XVidC_VideoMode XVidC_GetVideoModeId(u32 Width, u32 Height, u32 FrameRate,
+					u8 IsInterlaced)
+{
+	u32 Low;
+	u32 High;
+	u32 Mid;
+	u32 HActive;
+	u32 VActive;
+	u32 Rate;
+	u32 ResFound = (FALSE);
+	XVidC_VideoMode Mode;
+	u16 Index;
+
+	/* First, attempt a linear search on the custom video timing table. */
+	if(XVidC_CustomTimingModes) {
+	  for (Index = 0; Index < XVidC_NumCustomModes; Index++) {
+		HActive = XVidC_CustomTimingModes[Index].Timing.HActive;
+		VActive = XVidC_CustomTimingModes[Index].Timing.VActive;
+		Rate = XVidC_CustomTimingModes[Index].FrameRate;
+		if ((Width  == HActive) &&
+			(Height == VActive) &&
+			(FrameRate == Rate)) {
+			   return XVidC_CustomTimingModes[Index].VmId;
+		}
+	  }
+	}
+
+	if (IsInterlaced) {
+		Low = (XVIDC_VM_INTL_START);
+		High = (XVIDC_VM_INTL_END);
+	}
+	else {
+		Low = (XVIDC_VM_PROG_START);
+		High = (XVIDC_VM_PROG_END);
+	}
+
+	HActive = VActive = Rate = 0;
+
+	/* Binary search finds item in sorted array.
+	 * And returns index (zero based) of item
+	 * If item is not found returns flag remains
+	 * FALSE. Search key is "width or HActive"
+	 */
+	while (Low <= High) {
+		Mid = (Low + High) / 2;
+		HActive = XVidC_VideoTimingModes[Mid].Timing.HActive;
+		if (Width == HActive) {
+			ResFound = (TRUE);
+			break;
+		}
+		else if (Width < HActive) {
+			if (Mid == 0) {
+				break;
+			}
+			else {
+				High = Mid - 1;
+			}
+		}
+		else {
+			Low = Mid + 1;
+		}
+	}
+
+	 /* HActive matched at middle */
+	if (ResFound) {
+		/* Rewind to start index of mode with matching width */
+		while ((Mid > 0) &&
+			(XVidC_VideoTimingModes[Mid - 1].Timing.HActive ==
+								Width)) {
+			--Mid;
+		}
+
+		ResFound = (FALSE);
+		VActive = XVidC_VideoTimingModes[Mid].Timing.VActive;
+		Rate = XVidC_VideoTimingModes[Mid].FrameRate;
+
+		/* Now do a linear search for matching VActive and Frame
+		 * Rate
+		 */
+		while (HActive == Width) {
+			/* check current entry */
+			if ((VActive == Height) && (Rate == FrameRate)) {
+				ResFound = (TRUE);
+				break;
+			}
+			/* Check next entry */
+			else {
+				Mid = Mid + 1;
+				HActive =
+				XVidC_VideoTimingModes[Mid].Timing.HActive;
+				VActive =
+				XVidC_VideoTimingModes[Mid].Timing.VActive;
+				Rate = XVidC_VideoTimingModes[Mid].FrameRate;
+			}
+		}
+		Mode =
+		(ResFound) ? (XVidC_VideoMode)Mid : (XVIDC_VM_NOT_SUPPORTED);
+	}
+	else {
+		Mode = (XVIDC_VM_NOT_SUPPORTED);
+	}
+
+	return (Mode);
+}
+
+/******************************************************************************/
+/**
+ * This function returns the Video Mode ID that matches the detected input
+ * timing, frame rate and I/P flag
+ *
+ * @param	Timing is the pointer to timing parameters to match
+ * @param	FrameRate specifies refresh rate in HZ
+ * @param	IsInterlaced is flag.
+ *		      - 0 = Progressive
+ *			  - 1 = Interlaced.
+ * @param	IsExtensive is flag.
+ *		      - 0 = Basic matching of timing parameters
+ *			  - 1 = Extensive matching of timing parameters
+ *
+ * @return	Id of a supported video mode.
+ *
+ * @note	This function attempts to search for reduced blanking entries, if
+ *          any.
+ *
+*******************************************************************************/
+XVidC_VideoMode XVidC_GetVideoModeIdExtensive(XVidC_VideoTiming *Timing,
+											  u32 FrameRate,
+											  u8 IsInterlaced,
+											  u8 IsExtensive)
+{
+	u32 Low;
+	u32 High;
+	u32 Mid;
+	u32 HActive;
+	u32 VActive;
+	u32 Rate;
+	u32 ResFound = (FALSE);
+	XVidC_VideoMode Mode;
+	u16 Index;
+
+	/* First, attempt a linear search on the custom video timing table. */
+	if(XVidC_CustomTimingModes) {
+	  for (Index = 0; Index < XVidC_NumCustomModes; Index++) {
+		HActive = XVidC_CustomTimingModes[Index].Timing.HActive;
+		VActive = XVidC_CustomTimingModes[Index].Timing.VActive;
+		Rate = XVidC_CustomTimingModes[Index].FrameRate;
+		if ((HActive == Timing->HActive) && (VActive == Timing->VActive) &&
+				(Rate == FrameRate) && (IsExtensive == 0 || (
+			XVidC_CustomTimingModes[Index].Timing.HTotal == Timing->HTotal &&
+			XVidC_CustomTimingModes[Index].Timing.F0PVTotal ==
+					Timing->F0PVTotal &&
+			XVidC_CustomTimingModes[Index].Timing.HFrontPorch ==
+					Timing->HFrontPorch &&
+			XVidC_CustomTimingModes[Index].Timing.F0PVFrontPorch ==
+					Timing->F0PVFrontPorch &&
+			XVidC_CustomTimingModes[Index].Timing.HSyncWidth ==
+					Timing->HSyncWidth &&
+			XVidC_CustomTimingModes[Index].Timing.F0PVSyncWidth ==
+					Timing->F0PVSyncWidth &&
+			XVidC_CustomTimingModes[Index].Timing.VSyncPolarity ==
+					Timing->VSyncPolarity))) {
+				if (!IsInterlaced || IsExtensive == 0 || (
+						XVidC_CustomTimingModes[Index].Timing.F1VTotal ==
+						Timing->F1VTotal &&
+						XVidC_CustomTimingModes[Index].Timing.F1VFrontPorch ==
+								Timing->F1VFrontPorch &&
+						XVidC_CustomTimingModes[Index].Timing.F1VSyncWidth ==
+								Timing->F1VSyncWidth)) {
+					return XVidC_CustomTimingModes[Index].VmId;
+				}
+		}
+	  }
+	}
+
+	if (IsInterlaced) {
+		Low = (XVIDC_VM_INTL_START);
+		High = (XVIDC_VM_INTL_END);
+	}
+	else {
+		Low = (XVIDC_VM_PROG_START);
+		High = (XVIDC_VM_PROG_END);
+	}
+
+	HActive = VActive = Rate = 0;
+
+	/* Binary search finds item in sorted array.
+	 * And returns index (zero based) of item
+	 * If item is not found returns flag remains
+	 * FALSE. Search key is "Timing->HActive or HActive"
+	 */
+	while (Low <= High) {
+		Mid = (Low + High) / 2;
+		HActive = XVidC_VideoTimingModes[Mid].Timing.HActive;
+		if (Timing->HActive == HActive) {
+			ResFound = (TRUE);
+			break;
+		}
+		else if (Timing->HActive < HActive) {
+			if (Mid == 0) {
+				break;
+			}
+			else {
+				High = Mid - 1;
+			}
+		}
+		else {
+			Low = Mid + 1;
+		}
+	}
+
+	 /* HActive matched at middle */
+	if (ResFound) {
+		/* Rewind to start index of mode with matching Timing->HActive */
+		while ((Mid > 0) &&
+			(XVidC_VideoTimingModes[Mid - 1].Timing.HActive ==
+								Timing->HActive)) {
+			--Mid;
+		}
+
+		ResFound = (FALSE);
+		VActive = XVidC_VideoTimingModes[Mid].Timing.VActive;
+		Rate = XVidC_VideoTimingModes[Mid].FrameRate;
+
+		/* Now do a linear search for matching VActive and Frame
+		 * Rate
+		 */
+		while (HActive == Timing->HActive) {
+			/* check current entry */
+			if ((VActive == Timing->VActive) && (Rate == FrameRate) &&
+					(IsExtensive == 0 ||
+					(XVidC_VideoTimingModes[Mid].Timing.HTotal ==
+							Timing->HTotal &&
+					XVidC_VideoTimingModes[Mid].Timing.F0PVTotal ==
+							Timing->F0PVTotal &&
+					XVidC_VideoTimingModes[Mid].Timing.HFrontPorch ==
+							Timing->HFrontPorch &&
+					XVidC_VideoTimingModes[Mid].Timing.F0PVFrontPorch ==
+							Timing->F0PVFrontPorch &&
+					XVidC_VideoTimingModes[Mid].Timing.HSyncWidth ==
+							Timing->HSyncWidth &&
+					XVidC_VideoTimingModes[Mid].Timing.F0PVSyncWidth ==
+							Timing->F0PVSyncWidth &&
+					XVidC_VideoTimingModes[Mid].Timing.VSyncPolarity ==
+							Timing->VSyncPolarity))) {
+				if (!IsInterlaced || IsExtensive == 0 || (
+						XVidC_VideoTimingModes[Mid].Timing.F1VTotal ==
+								Timing->F1VTotal &&
+						XVidC_VideoTimingModes[Mid].Timing.F1VFrontPorch ==
+								Timing->F1VFrontPorch &&
+						XVidC_VideoTimingModes[Mid].Timing.F1VSyncWidth ==
+								Timing->F1VSyncWidth)) {
+					ResFound = (TRUE);
+					break;
+				} else {
+					Mid = Mid + 1;
+					HActive =
+					XVidC_VideoTimingModes[Mid].Timing.HActive;
+					VActive =
+					XVidC_VideoTimingModes[Mid].Timing.VActive;
+					Rate = XVidC_VideoTimingModes[Mid].FrameRate;
+				}
+			}
+			/* Check next entry */
+			else {
+				Mid = Mid + 1;
+				HActive =
+				XVidC_VideoTimingModes[Mid].Timing.HActive;
+				VActive =
+				XVidC_VideoTimingModes[Mid].Timing.VActive;
+				Rate = XVidC_VideoTimingModes[Mid].FrameRate;
+			}
+		}
+		Mode =
+		(ResFound) ? (XVidC_VideoMode)Mid : (XVIDC_VM_NOT_SUPPORTED);
+	}
+	else {
+		Mode = (XVIDC_VM_NOT_SUPPORTED);
+	}
+
+	return (Mode);
+}
+
+/******************************************************************************/
+/**
+ * This function returns the video mode ID that matches the detected input
+ * width, height, frame rate, interlaced or progressive, and reduced blanking.
+ *
+ * @param	Width specifies the number pixels per scanline.
+ * @param	Height specifies the number of scanline's.
+ * @param	FrameRate specifies refresh rate in HZ
+ * @param	IsInterlaced specifies interlaced or progressive mode:
+ *		- 0 = Progressive
+ *		- 1 = Interlaced.
+ * @param	RbN specifies the type of reduced blanking:
+ *		- 0 = No reduced blanking
+ *		- 1 = RB
+ *		- 2 = RB2
+ *
+ * @return	ID of a supported video mode.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+XVidC_VideoMode XVidC_GetVideoModeIdRb(u32 Width, u32 Height,
+		u32 FrameRate, u8 IsInterlaced, u8 RbN)
+{
+	XVidC_VideoMode VmId;
+	const XVidC_VideoTimingMode *VtmPtr;
+	u8 Found = 0;
+
+	VmId = XVidC_GetVideoModeId(Width, Height, FrameRate,
+				IsInterlaced);
+
+	VtmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VtmPtr) {
+		return XVIDC_VM_NOT_SUPPORTED;
+	}
+
+	while (!Found) {
+		VtmPtr = XVidC_GetVideoModeData(VmId);
+		if ((Height != VtmPtr->Timing.VActive) ||
+		    (Width != VtmPtr->Timing.HActive) ||
+		    (FrameRate != VtmPtr->FrameRate) ||
+		    (IsInterlaced && !XVidC_IsInterlaced(VmId))) {
+			VmId = XVIDC_VM_NOT_SUPPORTED;
+			break;
+		}
+		Found = XVidC_IsVtmRb(XVidC_GetVideoModeStr(VmId), RbN);
+		if (Found) {
+			break;
+		}
+		VmId = (XVidC_VideoMode)((int)VmId + 1);
+	}
+
+	return VmId;
+}
+
+/******************************************************************************/
+/**
+ * This function returns the pointer to video mode data at index provided.
+ *
+ * @param	VmId specifies the resolution id.
+ *
+ * @return	Pointer to XVidC_VideoTimingMode structure based on the given
+ *		video mode.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+const XVidC_VideoTimingMode *XVidC_GetVideoModeData(XVidC_VideoMode VmId)
+{
+	if (VmId < XVIDC_VM_NUM_SUPPORTED) {
+		return &XVidC_VideoTimingModes[VmId];
+	}
+
+	return XVidC_GetCustomVideoModeData(VmId);
+}
+
+/******************************************************************************/
+/**
+ *
+ * This function returns the resolution name for index specified.
+ *
+ * @param	VmId specifies the resolution id.
+ *
+ * @return	Pointer to a resolution name string.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+const char *XVidC_GetVideoModeStr(XVidC_VideoMode VmId)
+{
+	const XVidC_VideoTimingMode *VmPtr;
+
+	if (VmId == XVIDC_VM_CUSTOM) {
+		return ("Custom video mode");
+	}
+
+	VmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VmPtr) {
+		return ("Video mode not supported");
+	}
+
+	return VmPtr->Name;
+}
+
+/******************************************************************************/
+/**
+ * This function returns the frame rate name for index specified.
+ *
+ * @param	VmId specifies the resolution id.
+ *
+ * @return	Pointer to a frame rate name string.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+const char *XVidC_GetFrameRateStr(XVidC_VideoMode VmId)
+{
+	const XVidC_VideoTimingMode *VmPtr;
+
+	VmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VmPtr) {
+		return ("Video mode not supported");
+	}
+
+	switch (VmPtr->FrameRate) {
+		case (XVIDC_FR_24HZ):   return ("24Hz");
+		case (XVIDC_FR_25HZ):   return ("25Hz");
+		case (XVIDC_FR_30HZ):   return ("30Hz");
+		case (XVIDC_FR_48HZ):   return ("48Hz");
+		case (XVIDC_FR_50HZ):   return ("50Hz");
+		case (XVIDC_FR_56HZ):   return ("56Hz");
+		case (XVIDC_FR_60HZ):   return ("60Hz");
+		case (XVIDC_FR_65HZ):   return ("65Hz");
+		case (XVIDC_FR_67HZ):   return ("67Hz");
+		case (XVIDC_FR_70HZ):   return ("70Hz");
+		case (XVIDC_FR_72HZ):   return ("72Hz");
+		case (XVIDC_FR_75HZ):   return ("75Hz");
+		case (XVIDC_FR_85HZ):   return ("85Hz");
+		case (XVIDC_FR_87HZ):   return ("87Hz");
+		case (XVIDC_FR_88HZ):   return ("88Hz");
+		case (XVIDC_FR_96HZ):   return ("96Hz");
+		case (XVIDC_FR_100HZ):  return ("100Hz");
+		case (XVIDC_FR_120HZ):  return ("120Hz");
+		case (XVIDC_FR_144HZ):  return ("144Hz");
+		case (XVIDC_FR_200HZ):  return ("200Hz");
+		case (XVIDC_FR_240HZ):  return ("240Hz");
+
+		default:
+		     return ("Frame rate not supported");
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function returns a string representation of the enumerated type,
+ * XVidC_3DFormat.
+ *
+ * @param	Format specifies the value to convert.
+ *
+ * @return	Pointer to the converted string.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+const char *XVidC_Get3DFormatStr(XVidC_3DFormat Format)
+{
+	switch (Format) {
+		case XVIDC_3D_FRAME_PACKING:
+			return ("Frame Packing");
+
+		case XVIDC_3D_FIELD_ALTERNATIVE:
+			return ("Field Alternative");
+
+		case XVIDC_3D_LINE_ALTERNATIVE:
+			return ("Line Alternative");
+
+		case XVIDC_3D_SIDE_BY_SIDE_FULL:
+			return ("Side-by-Side(full)");
+
+		case XVIDC_3D_TOP_AND_BOTTOM_HALF:
+			return ("Top-and-Bottom(half)");
+
+		case XVIDC_3D_SIDE_BY_SIDE_HALF:
+			return ("Side-by-Side(half)");
+
+		default:
+			return ("Unknown");
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function returns the color format name for index specified.
+ *
+ * @param	ColorFormatId specifies the index of color format space.
+ *
+ * @return	Pointer to a color space name string.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+const char *XVidC_GetColorFormatStr(XVidC_ColorFormat ColorFormatId)
+{
+	switch (ColorFormatId) {
+		case XVIDC_CSF_RGB:            return ("RGB");
+		case XVIDC_CSF_YCRCB_444:      return ("YUV_444");
+		case XVIDC_CSF_YCRCB_422:      return ("YUV_422");
+		case XVIDC_CSF_YCRCB_420:      return ("YUV_420");
+		case XVIDC_CSF_YONLY:          return ("Y_ONLY");
+		case XVIDC_CSF_RGBA:           return ("RGBA");
+		case XVIDC_CSF_YCRCBA_444:     return ("YUVA_444");
+		case XVIDC_CSF_MEM_RGBX8:      return ("RGBX8");
+		case XVIDC_CSF_MEM_YUVX8:      return ("YUVX8");
+		case XVIDC_CSF_MEM_YUYV8:      return ("YUYV8");
+		case XVIDC_CSF_MEM_RGBA8:      return ("RGBA8");
+		case XVIDC_CSF_MEM_YUVA8:      return ("YUVA8");
+		case XVIDC_CSF_MEM_RGBX10:     return ("RGBX10");
+		case XVIDC_CSF_MEM_YUVX10:     return ("YUVX10");
+		case XVIDC_CSF_MEM_RGB565:     return ("RGB565");
+		case XVIDC_CSF_MEM_Y_UV8:      return ("Y_UV8");
+		case XVIDC_CSF_MEM_Y_UV8_420:  return ("Y_UV8_420");
+		case XVIDC_CSF_MEM_RGB8:       return ("RGB8");
+		case XVIDC_CSF_MEM_YUV8:       return ("YUV8");
+		case XVIDC_CSF_MEM_Y_UV10:     return ("Y_UV10");
+		case XVIDC_CSF_MEM_Y_UV10_420: return ("Y_UV10_420");
+		case XVIDC_CSF_MEM_Y8:         return ("Y8");
+		case XVIDC_CSF_MEM_Y10:        return ("Y10");
+		case XVIDC_CSF_MEM_BGRA8:      return ("BGRA8");
+		case XVIDC_CSF_MEM_BGRX8:      return ("BGRX8");
+		case XVIDC_CSF_MEM_UYVY8:      return ("UYVY8");
+		case XVIDC_CSF_MEM_BGR8:       return ("BGR8");
+		case XVIDC_CSF_YCBCR_422:      return ("YCBCR_422");
+		case XVIDC_CSF_YCBCR_420:      return ("YCBCR_420");
+		case XVIDC_CSF_YCBCR_444:      return ("YCBCR_444");
+		case XVIDC_CSF_MEM_RGBX12:     return ("RGBX12");
+		case XVIDC_CSF_MEM_RGB16:      return ("RGB16");
+		case XVIDC_CSF_MEM_YUVX12:     return ("YUVX12");
+		case XVIDC_CSF_MEM_YUV16:      return ("YUV16");
+		case XVIDC_CSF_MEM_Y_UV12:     return ("Y_UV12");
+		case XVIDC_CSF_MEM_Y_UV16:     return ("Y_UV16");
+		case XVIDC_CSF_MEM_Y_UV12_420: return ("Y_UV12_420");
+		case XVIDC_CSF_MEM_Y_UV16_420: return ("Y_UV16_420");
+		case XVIDC_CSF_MEM_Y12:        return ("Y12");
+		case XVIDC_CSF_MEM_Y16:        return ("Y16");
+		default:
+					       return ("Color space format not supported");
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function returns the frame rate for index specified.
+ *
+ * @param	VmId specifies the resolution id.
+ *
+ * @return	Frame rate in Hz.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+XVidC_FrameRate XVidC_GetFrameRate(XVidC_VideoMode VmId)
+{
+	const XVidC_VideoTimingMode *VmPtr;
+
+	VmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VmPtr) {
+		return XVIDC_FR_NUM_SUPPORTED;
+	}
+
+	return VmPtr->FrameRate;
+}
+
+/******************************************************************************/
+/**
+ * This function returns the timing parameters for specified resolution.
+ *
+ * @param	VmId specifies the resolution id.
+ *
+ * @return	Pointer to a XVidC_VideoTiming structure.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+const XVidC_VideoTiming *XVidC_GetTimingInfo(XVidC_VideoMode VmId)
+{
+	const XVidC_VideoTimingMode *VmPtr;
+
+	VmPtr = XVidC_GetVideoModeData(VmId);
+	if (!VmPtr) {
+		return NULL;
+	}
+
+	return &VmPtr->Timing;
+}
+
+/******************************************************************************/
+/**
+ * This function sets the VideoStream structure for the specified video format.
+ *
+ * @param	VidStrmPtr is a pointer to the XVidC_VideoStream structure to be
+ *		set.
+ * @param	VmId specifies the resolution ID.
+ * @param	ColorFormat specifies the color format type.
+ * @param	Bpc specifies the color depth/bits per color component.
+ * @param	Ppc specifies the pixels per clock.
+ *
+ * @return
+ *		- XST_SUCCESS if the timing for the supplied ID was found.
+ *		- XST_FAILURE, otherwise.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u32 XVidC_SetVideoStream(XVidC_VideoStream *VidStrmPtr, XVidC_VideoMode VmId,
+			 XVidC_ColorFormat ColorFormat, XVidC_ColorDepth Bpc,
+			 XVidC_PixelsPerClock Ppc)
+{
+	const XVidC_VideoTiming *TimingPtr;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(VidStrmPtr != NULL);
+	Xil_AssertNonvoid(ColorFormat < XVIDC_CSF_NUM_SUPPORTED);
+	Xil_AssertNonvoid((Bpc == XVIDC_BPC_6)  ||
+			  (Bpc == XVIDC_BPC_8)  ||
+			  (Bpc == XVIDC_BPC_10) ||
+			  (Bpc == XVIDC_BPC_12) ||
+			  (Bpc == XVIDC_BPC_14) ||
+			  (Bpc == XVIDC_BPC_16) ||
+			  (Bpc == XVIDC_BPC_UNKNOWN));
+	Xil_AssertNonvoid((Ppc == XVIDC_PPC_1) ||
+			  (Ppc == XVIDC_PPC_2) ||
+			  (Ppc == XVIDC_PPC_4) ||
+			  (Ppc == XVIDC_PPC_8));
+
+	/* Get the timing from the video timing table. */
+	if (VmId != XVIDC_VM_CUSTOM) {
+	  TimingPtr = XVidC_GetTimingInfo(VmId);
+	  if (!TimingPtr) {
+		return XST_FAILURE;
+	  }
+
+	  VidStrmPtr->Timing		= *TimingPtr;
+	  VidStrmPtr->FrameRate		= XVidC_GetFrameRate(VmId);
+	  VidStrmPtr->IsInterlaced	= XVidC_IsInterlaced(VmId);
+
+	} else {
+	  /* In custom timing no need to set Timing, FrameRate and IsInterlaced
+	   * as they are already set previously in wrapper code */
+	}
+
+	VidStrmPtr->VmId		= VmId;
+	VidStrmPtr->ColorFormatId	= ColorFormat;
+	VidStrmPtr->ColorDepth		= Bpc;
+	VidStrmPtr->PixPerClk		= Ppc;
+
+	/* Set stream to 2D. */
+	VidStrmPtr->Is3D			= FALSE;
+	VidStrmPtr->Info_3D.Format		= XVIDC_3D_UNKNOWN;
+	VidStrmPtr->Info_3D.Sampling.Method	= XVIDC_3D_SAMPLING_UNKNOWN;
+	VidStrmPtr->Info_3D.Sampling.Position	= XVIDC_3D_SAMPPOS_UNKNOWN;
+
+	return XST_SUCCESS;
+}
+
+/******************************************************************************/
+/**
+ * This function sets the VideoStream structure for the specified 3D video
+ * format.
+ *
+ * @param	VidStrmPtr is a pointer to the XVidC_VideoStream structure to be
+ *		set.
+ * @param	VmId specifies the resolution ID.
+ * @param	ColorFormat specifies the color format type.
+ * @param	Bpc specifies the color depth/bits per color component.
+ * @param	Ppc specifies the pixels per clock.
+ * @param	Info3DPtr is a pointer to a XVidC_3DInfo structure.
+ *
+ * @return
+ *		- XST_SUCCESS if the timing for the supplied ID was found.
+ *		- XST_FAILURE, otherwise.
+ *
+ * @return
+ *		- XST_SUCCESS
+ *		- XST_FAILURE
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u32 XVidC_Set3DVideoStream(XVidC_VideoStream *VidStrmPtr, XVidC_VideoMode VmId,
+			   XVidC_ColorFormat ColorFormat, XVidC_ColorDepth Bpc,
+			   XVidC_PixelsPerClock Ppc, XVidC_3DInfo *Info3DPtr)
+{
+	u32 Status;
+	u16 Vblank0;
+	u16 Vblank1;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(Info3DPtr != NULL);
+
+	/* Initialize with info for 2D frame. */
+	Status = XVidC_SetVideoStream(VidStrmPtr, VmId, ColorFormat, Bpc, Ppc);
+	if (Status != XST_SUCCESS) {
+		return XST_FAILURE;
+	}
+
+	/* Set stream to 3D. */
+	VidStrmPtr->Is3D	= TRUE;
+	VidStrmPtr->Info_3D	= *Info3DPtr;
+
+	/* Only 3D format supported is frame packing. */
+	if (Info3DPtr->Format != XVIDC_3D_FRAME_PACKING) {
+		return XST_FAILURE;
+	}
+
+	/* Update the timing based on the 3D format. */
+
+	/* An interlaced format is converted to a progressive frame: */
+	/*	3D VActive = (2D VActive * 4) + (2D VBlank field0) +
+						(2D Vblank field1 * 2) */
+	if (VidStrmPtr->IsInterlaced) {
+		Vblank0 = VidStrmPtr->Timing.F0PVTotal -
+						VidStrmPtr->Timing.VActive;
+		Vblank1 = VidStrmPtr->Timing.F1VTotal -
+						VidStrmPtr->Timing.VActive;
+		VidStrmPtr->Timing.VActive = (VidStrmPtr->Timing.VActive * 4) +
+						Vblank0 + (Vblank1 * 2);
+
+		/* Set VTotal */
+		VidStrmPtr->Timing.F0PVTotal *= 2;
+		VidStrmPtr->Timing.F0PVTotal += VidStrmPtr->Timing.F1VTotal * 2;
+
+		/* Clear field 1 values. */
+		VidStrmPtr->Timing.F1VFrontPorch = 0;
+		VidStrmPtr->Timing.F1VSyncWidth  = 0;
+		VidStrmPtr->Timing.F1VBackPorch  = 0;
+		VidStrmPtr->Timing.F1VTotal      = 0;
+
+		/* Set format to progressive */
+		VidStrmPtr->IsInterlaced = FALSE;
+	}
+	/* Progressive */
+	else {
+		/* 3D Vactive = (2D VActive * 2) + (2D VBlank) */
+		Vblank0 = VidStrmPtr->Timing.F0PVTotal -
+						VidStrmPtr->Timing.VActive;
+		VidStrmPtr->Timing.VActive = (VidStrmPtr->Timing.VActive * 2) +
+						Vblank0;
+
+		/* Set VTotal. */
+		VidStrmPtr->Timing.F0PVTotal = VidStrmPtr->Timing.F0PVTotal * 2;
+	}
+
+	return XST_SUCCESS;
+}
+
+/******************************************************************************/
+/**
+ * This function prints the stream information on STDIO/UART console.
+ *
+ * @param	Stream is a pointer to video stream.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVidC_ReportStreamInfo(const XVidC_VideoStream *Stream)
+{
+	if (!XVidC_GetVideoModeData(Stream->VmId) &&
+			(Stream->VmId != XVIDC_VM_CUSTOM)) {
+		xil_printf("\tThe stream ID (%d) is not supported.\r\n",
+				Stream->VmId);
+		return;
+	}
+
+	xil_printf("\tColor Format:     %s\r\n",
+			XVidC_GetColorFormatStr(Stream->ColorFormatId));
+	xil_printf("\tColor Depth:      %d\r\n", Stream->ColorDepth);
+	xil_printf("\tPixels Per Clock: %d\r\n", Stream->PixPerClk);
+	xil_printf("\tMode:             %s\r\n",
+			Stream->IsInterlaced ? "Interlaced" : "Progressive");
+
+	if (Stream->Is3D) {
+		xil_printf("\t3D Format:        %s\r\n",
+		XVidC_Get3DFormatStr(Stream->Info_3D.Format));
+	}
+
+	if (Stream->VmId == XVIDC_VM_CUSTOM) {
+		xil_printf("\tFrame Rate:       %dHz\r\n",
+				Stream->FrameRate);
+		xil_printf("\tResolution:       %dx%d [Custom Mode]\r\n",
+				Stream->Timing.HActive, Stream->Timing.VActive);
+		xil_printf("\tPixel Clock:      %d kHz\r\n",
+				(u32)(XVidC_GetPixelClockHzByHVFr(
+					Stream->Timing.HTotal,
+					Stream->Timing.F0PVTotal,
+					Stream->FrameRate)/1000));
+	}
+	else {
+		xil_printf("\tFrame Rate:       %s\r\n",
+				XVidC_GetFrameRateStr(Stream->VmId));
+		xil_printf("\tResolution:       %s\r\n",
+				XVidC_GetVideoModeStr(Stream->VmId));
+		xil_printf("\tPixel Clock:      %d kHz\r\n",
+				(u32)(XVidC_GetPixelClockHzByVmId(Stream->VmId)
+						/1000));
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function prints timing information on STDIO/Uart console.
+ *
+ * @param	Timing is a pointer to Video Timing structure of the stream.
+ * @param	IsInterlaced is a TRUE/FALSE flag that denotes the timing
+ *		parameter is for interlaced/progressive stream.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVidC_ReportTiming(const XVidC_VideoTiming *Timing, u8 IsInterlaced)
+{
+	xil_printf("\r\n\tHSYNC Timing: hav=%04d, hfp=%02d, hsw=%02d(hsp=%d), "
+			"hbp=%03d, htot=%04d \r\n", Timing->HActive,
+			Timing->HFrontPorch, Timing->HSyncWidth,
+			Timing->HSyncPolarity,
+			Timing->HBackPorch, Timing->HTotal);
+
+	/* Interlaced */
+	if (IsInterlaced) {
+		xil_printf("\tVSYNC Timing (Field 0): vav=%04d, vfp=%02d, "
+			"vsw=%02d(vsp=%d), vbp=%03d, vtot=%04d\r\n",
+			Timing->VActive, Timing->F0PVFrontPorch,
+			Timing->F0PVSyncWidth, Timing->VSyncPolarity,
+			Timing->F0PVBackPorch, Timing->F0PVTotal);
+	xil_printf("\tVSYNC Timing (Field 1): vav=%04d, vfp=%02d, "
+			"vsw=%02d(vsp=%d), vbp=%03d, vtot=%04d\r\n",
+			Timing->VActive, Timing->F1VFrontPorch,
+			Timing->F1VSyncWidth, Timing->VSyncPolarity,
+			Timing->F1VBackPorch, Timing->F1VTotal);
+	}
+	/* Progressive */
+	else {
+		xil_printf("\tVSYNC Timing: vav=%04d, vfp=%02d, "
+			"vsw=%02d(vsp=%d), vbp=%03d, vtot=%04d\r\n",
+			Timing->VActive, Timing->F0PVFrontPorch,
+			Timing->F0PVSyncWidth, Timing->VSyncPolarity,
+			Timing->F0PVBackPorch, Timing->F0PVTotal);
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function returns the pointer to video mode data at the provided index
+ * of the custom video mode table.
+ *
+ * @param	VmId specifies the resolution ID.
+ *
+ * @return	Pointer to XVidC_VideoTimingMode structure based on the given
+ *		video mode.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+static const XVidC_VideoTimingMode *XVidC_GetCustomVideoModeData(
+		XVidC_VideoMode VmId)
+{
+	u16 Index;
+
+	for (Index = 0; Index < XVidC_NumCustomModes; Index++) {
+		if (VmId == (XVidC_CustomTimingModes[Index].VmId)) {
+			return &(XVidC_CustomTimingModes[Index]);
+		}
+	}
+
+	/* ID not found within the custom video mode table. */
+	return NULL;
+}
+
+/******************************************************************************/
+/**
+ * This function returns whether or not the video timing mode is a reduced
+ * blanking mode or not.
+ *
+ * @param	VideoModeStr specifies the resolution name string.
+ * @param	RbN specifies the type of reduced blanking:
+ *		- 0 = No Reduced Blanking
+ *		- 1 = RB
+ *		- 2 = RB2
+ *
+ * @return	If the reduced blanking type is compatible with the video mode:
+ *		- 0 = Not supported
+ *		- 1 = Video mode supports the RB type
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+static u8 XVidC_IsVtmRb(const char *VideoModeStr, u8 RbN)
+{
+	while ((*VideoModeStr !='\0') && (*VideoModeStr != 'R')) {
+		VideoModeStr++;
+	}
+
+	if (*(VideoModeStr + 2) == ')') {
+		return RbN == 1;
+	}
+	if (*(VideoModeStr + 2) == '2') {
+		return RbN == 2;
+	}
+	return 0;
+}
+
+/******************************************************************************/
+/**
+ * This function prints the stream information to passed buffer
+ *
+ * @param	Stream is a pointer to video stream.
+ * @param	buff Buffer to print to
+ * @param	buff_size size off buff passed
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+int XVidC_ShowStreamInfo(const XVidC_VideoStream *Stream, char *buff, int buff_size)
+{
+	int strSize = 0;
+
+	strSize = scnprintf(buff+strSize, buff_size-strSize,
+				"\r\n  Stream Info\r\n" \
+				" -------------\r\n");
+	if (!XVidC_GetVideoModeData(Stream->VmId) &&
+			(Stream->VmId != XVIDC_VM_CUSTOM)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"\tThe stream ID (%d) is not supported.\r\n",
+			Stream->VmId);
+		return strSize;
+	}
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tColor Format:     %s\r\n",
+			XVidC_GetColorFormatStr(Stream->ColorFormatId));
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tColor Depth:      %d\r\n", Stream->ColorDepth);
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tPixels Per Clock: %d\r\n", Stream->PixPerClk);
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tMode:             %s\r\n",
+			Stream->IsInterlaced ? "Interlaced" : "Progressive");
+
+	if (Stream->Is3D) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"\t3D Format:        %s\r\n",
+				XVidC_Get3DFormatStr(Stream->Info_3D.Format));
+	}
+
+	if (Stream->VmId == XVIDC_VM_CUSTOM) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tFrame Rate:       %dHz\r\n",
+				Stream->FrameRate);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tResolution:       %dx%d [Custom Mode]\r\n",
+				Stream->Timing.HActive, Stream->Timing.VActive);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tPixel Clock:      %lld\r\n",
+				XVidC_GetPixelClockHzByHVFr(
+					Stream->Timing.HTotal,
+					Stream->Timing.F0PVTotal,
+					Stream->FrameRate));
+	}
+	else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tFrame Rate:       %s\r\n",
+				XVidC_GetFrameRateStr(Stream->VmId));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tResolution:       %s\r\n",
+				XVidC_GetVideoModeStr(Stream->VmId));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\tPixel Clock:      %lld\r\n",
+				XVidC_GetPixelClockHzByVmId(Stream->VmId));
+	}
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\n  Stream Timing\r\n" \
+				" ----------------\r\n");
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+		"\r\n\tHSYNC Timing: hav=%04d, hfp=%02d, hsw=%02d(hsp=%d), " \
+		"hbp=%03d, htot=%04d \n\r", Stream->Timing.HActive,
+			Stream->Timing.HFrontPorch, Stream->Timing.HSyncWidth,
+			Stream->Timing.HSyncPolarity,
+			Stream->Timing.HBackPorch, Stream->Timing.HTotal);
+
+	/* Interlaced */
+	if (Stream->IsInterlaced) {
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+		"\tVSYNC Timing (Field 0): vav=%04d, vfp=%02d, " \
+		"vsw=%02d(vsp=%d), vbp=%03d, vtot=%04d\n\r",
+			Stream->Timing.VActive,       Stream->Timing.F0PVFrontPorch,
+			Stream->Timing.F0PVSyncWidth, Stream->Timing.VSyncPolarity,
+			Stream->Timing.F0PVBackPorch, Stream->Timing.F0PVTotal);
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+		"\tVSYNC Timing (Field 1): vav=%04d, vfp=%02d, " \
+		"vsw=%02d(vsp=%d), vbp=%03d, vtot=%04d\r\n",
+			Stream->Timing.VActive,      Stream->Timing.F1VFrontPorch,
+			Stream->Timing.F1VSyncWidth, Stream->Timing.VSyncPolarity,
+			Stream->Timing.F1VBackPorch, Stream->Timing.F1VTotal);
+	}
+	/* Progressive */
+	else {
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+		"\tVSYNC Timing: vav=%04d, vfp=%02d, " \
+		"vsw=%02d(vsp=%d), vbp=%03d, vtot=%04d\r\n\r\n",
+			Stream->Timing.VActive,       Stream->Timing.F0PVFrontPorch,
+			Stream->Timing.F0PVSyncWidth, Stream->Timing.VSyncPolarity,
+			Stream->Timing.F0PVBackPorch, Stream->Timing.F0PVTotal);
+	}
+
+	return strSize;
+}
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvidc.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvidc.h
@@ -0,0 +1,699 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvidc.h
+ * @{
+ * @details
+ *
+ * Contains common structures, definitions, macros, and utility functions that
+ * are typically used by video-related drivers and applications.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   rc,  01/10/15 Initial release.
+ *       als
+ * 2.0   als  08/14/15 Added new video timings.
+ * 2.2   als  02/01/16 Functions with pointer arguments that don't modify
+ *                     contents now const.
+ *                     Added ability to insert a custom video timing table:
+ *                         XVidC_RegisterCustomTimingModes
+ *                         XVidC_UnregisterCustomTimingMode
+ *       yh            Added 3D support.
+ * 3.0   aad  05/13/16 Added API to search for RB video modes.
+ *       als  05/16/16 Added Y-only to color format enum.
+ * 3.1   rco  07/26/17 Moved timing table extern definition to xvidc.c
+ *                     Added video-in-memory color formats
+ *                     Updated XVidC_RegisterCustomTimingModes API signature
+ * 4.1   rco  11/23/17 Added new memory formats
+ *                     Added xil_printf include statement
+ *                     Added new API XVidC_GetVideoModeIdWBlanking
+ *                     Fix C++ warnings
+ * 4.2   jsr  07/22/17 Added new video modes, framerates, color formats for SDI
+ *                     New member AspectRatio is added to video stream structure
+ *                     Reordered XVidC_VideoMode enum variables and corrected the
+ *                     memory format enums
+ *       aad  07/10/17 Add XVIDC_VM_3840x2160_60_P_RB video format
+ *       vyc  10/04/17 Added new streaming alpha formats and new memory formats
+ *       aad  09/05/17 Add XVIDC_VM_1366x768_60_P_RB resolution
+ * 4.3   eb   26/01/18 Added API XVidC_GetVideoModeIdExtensive
+ *       jsr  02/22/18 Added XVIDC_CSF_YCBCR_420 color space format
+ *       vyc  04/04/18 Added BGR8 memory format
+ * 4.5   jsr  07/03/18 Added XVIDC_VM_720x486_60_I video format
+ * 4.5   yas  03/08/19 Added support for frame rates 144HZ and 240HZ
+ * 4.6   mmo  02/14/19 Added 5k, 8k, 10k and Low Resolution with 200Hz, 240Hz
+ * </pre>
+ *
+*******************************************************************************/
+
+#ifndef XVIDC_H_  /* Prevent circular inclusions by using protection macros. */
+#define XVIDC_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xil_types.h"
+#include "xil_printf.h"
+
+/************************** Constant Definitions ******************************/
+
+/**
+ * This typedef enumerates the list of available standard display monitor
+ * timings as specified in the xvidc_timings_table.c file. The naming format is:
+ *
+ * XVIDC_VM_<RESOLUTION>_<REFRESH RATE (HZ)>_<P|I>(_RB)
+ *
+ * Where RB stands for reduced blanking.
+ */
+typedef enum {
+	/* Interlaced modes. */
+	XVIDC_VM_720x480_60_I = 0,
+	XVIDC_VM_720x486_60_I,
+	XVIDC_VM_720x576_50_I,
+	XVIDC_VM_1440x480_60_I,
+	XVIDC_VM_1440x480_120_I,
+	XVIDC_VM_1440x480_240_I,
+	XVIDC_VM_1440x576_50_I,
+	XVIDC_VM_1440x576_100_I,
+	XVIDC_VM_1440x576_200_I,
+	XVIDC_VM_1920x1080_48_I,
+	XVIDC_VM_1920x1080_50_I,
+	XVIDC_VM_1920x1080_60_I,
+	XVIDC_VM_1920x1080_96_I,
+	XVIDC_VM_1920x1080_100_I,
+	XVIDC_VM_1920x1080_120_I,
+	XVIDC_VM_2048x1080_48_I,
+	XVIDC_VM_2048x1080_50_I,
+	XVIDC_VM_2048x1080_60_I,
+	XVIDC_VM_2048x1080_96_I,
+	XVIDC_VM_2048x1080_100_I,
+	XVIDC_VM_2048x1080_120_I,
+	XVIDC_VM_2880x480_60_I,
+	XVIDC_VM_2880x576_50_I,
+
+
+	/* Progressive modes. */
+	XVIDC_VM_640x350_85_P,
+	XVIDC_VM_640x480_60_P,
+	XVIDC_VM_640x480_72_P,
+	XVIDC_VM_640x480_75_P,
+	XVIDC_VM_640x480_85_P,
+	XVIDC_VM_720x400_85_P,
+	XVIDC_VM_720x480_60_P,
+	XVIDC_VM_720x480_120_P,
+	XVIDC_VM_720x480_240_P,
+	XVIDC_VM_720x576_50_P,
+	XVIDC_VM_720x576_100_P,
+	XVIDC_VM_720x576_200_P,
+	XVIDC_VM_800x600_56_P,
+	XVIDC_VM_800x600_60_P,
+	XVIDC_VM_800x600_72_P,
+	XVIDC_VM_800x600_75_P,
+	XVIDC_VM_800x600_85_P,
+	XVIDC_VM_800x600_120_P_RB,
+	XVIDC_VM_848x480_60_P,
+	XVIDC_VM_1024x768_60_P,
+	XVIDC_VM_1024x768_70_P,
+	XVIDC_VM_1024x768_75_P,
+	XVIDC_VM_1024x768_85_P,
+	XVIDC_VM_1024x768_120_P_RB,
+	XVIDC_VM_1152x864_75_P,
+	XVIDC_VM_1280x720_24_P,
+	XVIDC_VM_1280x720_25_P,
+	XVIDC_VM_1280x720_30_P,
+	XVIDC_VM_1280x720_50_P,
+	XVIDC_VM_1280x720_60_P,
+	XVIDC_VM_1280x720_100_P,
+	XVIDC_VM_1280x720_120_P,
+	XVIDC_VM_1280x768_60_P,
+	XVIDC_VM_1280x768_60_P_RB,
+	XVIDC_VM_1280x768_75_P,
+	XVIDC_VM_1280x768_85_P,
+	XVIDC_VM_1280x768_120_P_RB,
+	XVIDC_VM_1280x800_60_P,
+	XVIDC_VM_1280x800_60_P_RB,
+	XVIDC_VM_1280x800_75_P,
+	XVIDC_VM_1280x800_85_P,
+	XVIDC_VM_1280x800_120_P_RB,
+	XVIDC_VM_1280x960_60_P,
+	XVIDC_VM_1280x960_85_P,
+	XVIDC_VM_1280x960_120_P_RB,
+	XVIDC_VM_1280x1024_60_P,
+	XVIDC_VM_1280x1024_75_P,
+	XVIDC_VM_1280x1024_85_P,
+	XVIDC_VM_1280x1024_120_P_RB,
+	XVIDC_VM_1360x768_60_P,
+	XVIDC_VM_1360x768_120_P_RB,
+	XVIDC_VM_1366x768_60_P,
+	XVIDC_VM_1366x768_60_P_RB,
+	XVIDC_VM_1400x1050_60_P,
+	XVIDC_VM_1400x1050_60_P_RB,
+	XVIDC_VM_1400x1050_75_P,
+	XVIDC_VM_1400x1050_85_P,
+	XVIDC_VM_1400x1050_120_P_RB,
+	XVIDC_VM_1440x240_60_P,
+	XVIDC_VM_1440x288_50_P,
+	XVIDC_VM_1440x480_60_P,
+	XVIDC_VM_1440x576_50_P,
+	XVIDC_VM_1440x900_60_P,
+	XVIDC_VM_1440x900_60_P_RB,
+	XVIDC_VM_1440x900_75_P,
+	XVIDC_VM_1440x900_85_P,
+	XVIDC_VM_1440x900_120_P_RB,
+	XVIDC_VM_1600x1200_60_P,
+	XVIDC_VM_1600x1200_65_P,
+	XVIDC_VM_1600x1200_70_P,
+	XVIDC_VM_1600x1200_75_P,
+	XVIDC_VM_1600x1200_85_P,
+	XVIDC_VM_1600x1200_120_P_RB,
+	XVIDC_VM_1680x720_24_P,
+	XVIDC_VM_1680x720_25_P,
+	XVIDC_VM_1680x720_30_P,
+	XVIDC_VM_1680x720_50_P,
+	XVIDC_VM_1680x720_60_P,
+	XVIDC_VM_1680x720_100_P,
+	XVIDC_VM_1680x720_120_P,
+	XVIDC_VM_1680x1050_50_P,
+	XVIDC_VM_1680x1050_60_P,
+	XVIDC_VM_1680x1050_60_P_RB,
+	XVIDC_VM_1680x1050_75_P,
+	XVIDC_VM_1680x1050_85_P,
+	XVIDC_VM_1680x1050_120_P_RB,
+	XVIDC_VM_1792x1344_60_P,
+	XVIDC_VM_1792x1344_75_P,
+	XVIDC_VM_1792x1344_120_P_RB,
+	XVIDC_VM_1856x1392_60_P,
+	XVIDC_VM_1856x1392_75_P,
+	XVIDC_VM_1856x1392_120_P_RB,
+	XVIDC_VM_1920x1080_24_P,
+	XVIDC_VM_1920x1080_25_P,
+	XVIDC_VM_1920x1080_30_P,
+	XVIDC_VM_1920x1080_48_P,
+	XVIDC_VM_1920x1080_50_P,
+	XVIDC_VM_1920x1080_60_P,
+	XVIDC_VM_1920x1080_100_P,
+	XVIDC_VM_1920x1080_120_P,
+	XVIDC_VM_1920x1200_60_P,
+	XVIDC_VM_1920x1200_60_P_RB,
+	XVIDC_VM_1920x1200_75_P,
+	XVIDC_VM_1920x1200_85_P,
+	XVIDC_VM_1920x1200_120_P_RB,
+	XVIDC_VM_1920x1440_60_P,
+	XVIDC_VM_1920x1440_75_P,
+	XVIDC_VM_1920x1440_120_P_RB,
+	XVIDC_VM_1920x2160_60_P,
+	XVIDC_VM_2048x1080_24_P,
+	XVIDC_VM_2048x1080_25_P,
+	XVIDC_VM_2048x1080_30_P,
+	XVIDC_VM_2048x1080_48_P,
+	XVIDC_VM_2048x1080_50_P,
+	XVIDC_VM_2048x1080_60_P,
+	XVIDC_VM_2048x1080_100_P,
+	XVIDC_VM_2048x1080_120_P,
+	XVIDC_VM_2560x1080_24_P,
+	XVIDC_VM_2560x1080_25_P,
+	XVIDC_VM_2560x1080_30_P,
+	XVIDC_VM_2560x1080_48_P,
+	XVIDC_VM_2560x1080_50_P,
+	XVIDC_VM_2560x1080_60_P,
+	XVIDC_VM_2560x1080_100_P,
+	XVIDC_VM_2560x1080_120_P,
+	XVIDC_VM_2560x1600_60_P,
+	XVIDC_VM_2560x1600_60_P_RB,
+	XVIDC_VM_2560x1600_75_P,
+	XVIDC_VM_2560x1600_85_P,
+	XVIDC_VM_2560x1600_120_P_RB,
+	XVIDC_VM_2880x240_60_P,
+	XVIDC_VM_2880x288_50_P,
+	XVIDC_VM_2880x480_60_P,
+	XVIDC_VM_2880x576_50_P,
+	XVIDC_VM_3840x2160_24_P,
+	XVIDC_VM_3840x2160_25_P,
+	XVIDC_VM_3840x2160_30_P,
+	XVIDC_VM_3840x2160_48_P,
+	XVIDC_VM_3840x2160_50_P,
+	XVIDC_VM_3840x2160_60_P,
+	XVIDC_VM_3840x2160_60_P_RB,
+	XVIDC_VM_3840x2160_100_P,
+	XVIDC_VM_3840x2160_120_P,
+	XVIDC_VM_4096x2160_24_P,
+	XVIDC_VM_4096x2160_25_P,
+	XVIDC_VM_4096x2160_30_P,
+	XVIDC_VM_4096x2160_48_P,
+	XVIDC_VM_4096x2160_50_P,
+	XVIDC_VM_4096x2160_60_P,
+	XVIDC_VM_4096x2160_60_P_RB,
+	XVIDC_VM_4096x2160_100_P,
+	XVIDC_VM_4096x2160_120_P,
+	XVIDC_VM_5120x2160_24_P,
+	XVIDC_VM_5120x2160_25_P,
+	XVIDC_VM_5120x2160_30_P,
+	XVIDC_VM_5120x2160_48_P,
+	XVIDC_VM_5120x2160_50_P,
+	XVIDC_VM_5120x2160_60_P,
+	XVIDC_VM_5120x2160_100_P,
+	XVIDC_VM_5120x2160_120_P,
+	XVIDC_VM_7680x4320_24_P,
+	XVIDC_VM_7680x4320_25_P,
+	XVIDC_VM_7680x4320_30_P,
+	XVIDC_VM_7680x4320_48_P,
+	XVIDC_VM_7680x4320_50_P,
+	XVIDC_VM_7680x4320_60_P,
+	XVIDC_VM_7680x4320_120_P,
+	XVIDC_VM_7680x4320_100_P,
+	XVIDC_VM_10240x4320_24_P,
+	XVIDC_VM_10240x4320_25_P,
+	XVIDC_VM_10240x4320_30_P,
+	XVIDC_VM_10240x4320_48_P,
+	XVIDC_VM_10240x4320_50_P,
+	XVIDC_VM_10240x4320_60_P,
+	XVIDC_VM_10240x4320_100_P,
+	XVIDC_VM_10240x4320_120_P,
+
+	XVIDC_VM_NUM_SUPPORTED,
+	XVIDC_VM_USE_EDID_PREFERRED,
+	XVIDC_VM_NO_INPUT,
+	XVIDC_VM_NOT_SUPPORTED,
+	XVIDC_VM_CUSTOM,
+
+	/* Marks beginning/end of interlaced/progressive modes in the table. */
+	XVIDC_VM_INTL_START = XVIDC_VM_720x480_60_I,
+	XVIDC_VM_PROG_START = XVIDC_VM_640x350_85_P,
+	XVIDC_VM_INTL_END = (XVIDC_VM_PROG_START - 1),
+	XVIDC_VM_PROG_END = (XVIDC_VM_NUM_SUPPORTED - 1),
+
+	/* Common naming. */
+	XVIDC_VM_480_60_I = XVIDC_VM_720x480_60_I,
+	XVIDC_VM_486_60_I = XVIDC_VM_720x486_60_I,
+	XVIDC_VM_576_50_I = XVIDC_VM_720x576_50_I,
+	XVIDC_VM_1080_50_I = XVIDC_VM_1920x1080_50_I,
+	XVIDC_VM_1080_60_I = XVIDC_VM_1920x1080_60_I,
+	XVIDC_VM_VGA_60_P = XVIDC_VM_640x480_60_P,
+	XVIDC_VM_480_60_P = XVIDC_VM_720x480_60_P,
+	XVIDC_VM_SVGA_60_P = XVIDC_VM_800x600_60_P,
+	XVIDC_VM_XGA_60_P = XVIDC_VM_1024x768_60_P,
+	XVIDC_VM_720_50_P = XVIDC_VM_1280x720_50_P,
+	XVIDC_VM_720_60_P = XVIDC_VM_1280x720_60_P,
+	XVIDC_VM_WXGA_60_P = XVIDC_VM_1366x768_60_P,
+	XVIDC_VM_UXGA_60_P = XVIDC_VM_1600x1200_60_P,
+	XVIDC_VM_WSXGA_60_P = XVIDC_VM_1680x1050_60_P,
+	XVIDC_VM_1080_24_P = XVIDC_VM_1920x1080_24_P,
+	XVIDC_VM_1080_25_P = XVIDC_VM_1920x1080_25_P,
+	XVIDC_VM_1080_30_P = XVIDC_VM_1920x1080_30_P,
+	XVIDC_VM_1080_50_P = XVIDC_VM_1920x1080_50_P,
+	XVIDC_VM_1080_60_P = XVIDC_VM_1920x1080_60_P,
+	XVIDC_VM_WUXGA_60_P = XVIDC_VM_1920x1200_60_P,
+	XVIDC_VM_UHD2_60_P = XVIDC_VM_1920x2160_60_P,
+	XVIDC_VM_UHD_24_P = XVIDC_VM_3840x2160_24_P,
+	XVIDC_VM_UHD_25_P = XVIDC_VM_3840x2160_25_P,
+	XVIDC_VM_UHD_30_P = XVIDC_VM_3840x2160_30_P,
+	XVIDC_VM_UHD_60_P = XVIDC_VM_3840x2160_60_P,
+	XVIDC_VM_4K2K_60_P = XVIDC_VM_4096x2160_60_P,
+	XVIDC_VM_4K2K_60_P_RB = XVIDC_VM_4096x2160_60_P_RB,
+} XVidC_VideoMode;
+
+/**
+ * Progressive/interlaced video format.
+ */
+typedef enum {
+	XVIDC_VF_PROGRESSIVE = 0,
+	XVIDC_VF_INTERLACED,
+	XVIDC_VF_UNKNOWN
+} XVidC_VideoFormat;
+
+/**
+ * Frame rate.
+ */
+typedef enum {
+	XVIDC_FR_24HZ = 24,
+	XVIDC_FR_25HZ = 25,
+	XVIDC_FR_30HZ = 30,
+	XVIDC_FR_48HZ = 48,
+	XVIDC_FR_50HZ = 50,
+	XVIDC_FR_56HZ = 56,
+	XVIDC_FR_60HZ = 60,
+	XVIDC_FR_65HZ = 65,
+	XVIDC_FR_67HZ = 67,
+	XVIDC_FR_70HZ = 70,
+	XVIDC_FR_72HZ = 72,
+	XVIDC_FR_75HZ = 75,
+	XVIDC_FR_85HZ = 85,
+	XVIDC_FR_87HZ = 87,
+	XVIDC_FR_88HZ = 88,
+	XVIDC_FR_96HZ = 96,
+	XVIDC_FR_100HZ = 100,
+	XVIDC_FR_120HZ = 120,
+	XVIDC_FR_144HZ = 144,
+	XVIDC_FR_200HZ = 200,
+	XVIDC_FR_240HZ = 240,
+	XVIDC_FR_NUM_SUPPORTED = 21,
+	XVIDC_FR_UNKNOWN
+} XVidC_FrameRate;
+
+/**
+ * Color depth - bits per color component.
+ */
+typedef enum {
+	XVIDC_BPC_6 = 6,
+	XVIDC_BPC_8 = 8,
+	XVIDC_BPC_10 = 10,
+	XVIDC_BPC_12 = 12,
+	XVIDC_BPC_14 = 14,
+	XVIDC_BPC_16 = 16,
+	XVIDC_BPC_NUM_SUPPORTED = 6,
+	XVIDC_BPC_UNKNOWN
+} XVidC_ColorDepth;
+
+/**
+ * Pixels per clock.
+ */
+typedef enum {
+	XVIDC_PPC_1 = 1,
+	XVIDC_PPC_2 = 2,
+	XVIDC_PPC_4 = 4,
+	XVIDC_PPC_8 = 8,
+	XVIDC_PPC_NUM_SUPPORTED = 4,
+} XVidC_PixelsPerClock;
+
+/**
+ * Color space format.
+ */
+typedef enum {
+	/* Streaming video formats */
+	XVIDC_CSF_RGB = 0,
+	XVIDC_CSF_YCRCB_444,
+	XVIDC_CSF_YCRCB_422,
+	XVIDC_CSF_YCRCB_420,
+	XVIDC_CSF_YONLY,
+	XVIDC_CSF_RGBA,
+	XVIDC_CSF_YCRCBA_444,
+
+	/* 6 empty slots reserved for video formats for future
+	 * extension
+	 */
+
+	/* Video in memory formats */
+	XVIDC_CSF_MEM_RGBX8 = 10,   // [31:0] x:B:G:R 8:8:8:8
+	XVIDC_CSF_MEM_YUVX8,        // [31:0] x:V:U:Y 8:8:8:8
+	XVIDC_CSF_MEM_YUYV8,        // [31:0] V:Y:U:Y 8:8:8:8
+	XVIDC_CSF_MEM_RGBA8,        // [31:0] A:B:G:R 8:8:8:8
+	XVIDC_CSF_MEM_YUVA8,        // [31:0] A:V:U:Y 8:8:8:8
+	XVIDC_CSF_MEM_RGBX10,       // [31:0] x:B:G:R 2:10:10:10
+	XVIDC_CSF_MEM_YUVX10,       // [31:0] x:V:U:Y 2:10:10:10
+	XVIDC_CSF_MEM_RGB565,       // [15:0] B:G:R 5:6:5
+	XVIDC_CSF_MEM_Y_UV8,        // [15:0] Y:Y 8:8, [15:0] V:U 8:8
+	XVIDC_CSF_MEM_Y_UV8_420,    // [15:0] Y:Y 8:8, [15:0] V:U 8:8
+	XVIDC_CSF_MEM_RGB8,         // [23:0] B:G:R 8:8:8
+	XVIDC_CSF_MEM_YUV8,         // [24:0] V:U:Y 8:8:8
+	XVIDC_CSF_MEM_Y_UV10,       // [31:0] x:Y:Y:Y 2:10:10:10 [31:0] x:U:V:U 2:10:10:10
+	XVIDC_CSF_MEM_Y_UV10_420,   // [31:0] x:Y:Y:Y 2:10:10:10 [31:0] x:U:V:U 2:10:10:10
+	XVIDC_CSF_MEM_Y8,           // [31:0] Y:Y:Y:Y 8:8:8:8
+	XVIDC_CSF_MEM_Y10,          // [31:0] x:Y:Y:Y 2:10:10:10
+	XVIDC_CSF_MEM_BGRA8,        // [31:0] A:R:G:B 8:8:8:8
+	XVIDC_CSF_MEM_BGRX8,        // [31:0] X:R:G:B 8:8:8:8
+	XVIDC_CSF_MEM_UYVY8,        // [31:0] Y:V:Y:U 8:8:8:8
+	XVIDC_CSF_MEM_BGR8,         // [23:0] R:G:B 8:8:8
+	XVIDC_CSF_MEM_RGBX12,       // [39:0] x:R:G:B 4:12:12:12
+	XVIDC_CSF_MEM_YUVX12,       // [39:0] x:V:U:Y 4:12:12:12
+	XVIDC_CSF_MEM_Y_UV12,       // [23:0] Y:Y 12:12, [23:0] V:U 12:12
+	XVIDC_CSF_MEM_Y_UV12_420,   // [23:0] Y:Y 12:12, [23:0] V:U 12:12
+	XVIDC_CSF_MEM_Y12,          // [39:0] x:Y2:Y1:Y0 4:12:12:12
+	XVIDC_CSF_MEM_RGB16,        // [47:0] R:G:B 16:16:16
+	XVIDC_CSF_MEM_YUV16,        // [47:0] V:U:Y 16:16:16
+	XVIDC_CSF_MEM_Y_UV16,       // [31:0] Y:Y 16:16, [31:0] V:U 16:16
+	XVIDC_CSF_MEM_Y_UV16_420,   // [31:0] Y:Y 16:16, [31:0] V:U 16:16
+	XVIDC_CSF_MEM_Y16,          // [47:0] Y2:Y1:Y0 16:16:16
+	XVIDC_CSF_MEM_END,          // End of memory formats
+
+	/* Streaming formats with components re-ordered */
+	XVIDC_CSF_YCBCR_422 = 64,
+	XVIDC_CSF_YCBCR_420,
+	XVIDC_CSF_YCBCR_444,
+
+	XVIDC_CSF_NUM_SUPPORTED,    // includes the reserved slots
+	XVIDC_CSF_UNKNOWN,
+	XVIDC_CSF_STRM_START = XVIDC_CSF_RGB,
+	XVIDC_CSF_STRM_END   = XVIDC_CSF_YONLY,
+	XVIDC_CSF_MEM_START  = XVIDC_CSF_MEM_RGBX8,
+	XVIDC_CSF_NUM_STRM   = (XVIDC_CSF_STRM_END - XVIDC_CSF_STRM_START + 1),
+	XVIDC_CSF_NUM_MEM    = (XVIDC_CSF_MEM_END - XVIDC_CSF_MEM_START)
+} XVidC_ColorFormat;
+
+
+/**
+ * Image Aspect Ratio.
+ */
+typedef enum {
+	XVIDC_AR_4_3 = 0,
+	XVIDC_AR_16_9 = 1,
+	XVIDC_AR_64_27 = 2,
+	XVIDC_AR_256_135 = 3
+} XVidC_AspectRatio;
+
+/**
+ * Color space conversion standard.
+ */
+typedef enum {
+	XVIDC_BT_2020 = 0,
+	XVIDC_BT_709,
+	XVIDC_BT_601,
+	XVIDC_BT_NUM_SUPPORTED,
+	XVIDC_BT_UNKNOWN
+} XVidC_ColorStd;
+
+/**
+ * Color conversion output range.
+ */
+typedef enum {
+	XVIDC_CR_16_235 = 0,
+	XVIDC_CR_16_240,
+	XVIDC_CR_0_255,
+	XVIDC_CR_NUM_SUPPORTED,
+	XVIDC_CR_UNKNOWN_RANGE
+} XVidC_ColorRange;
+
+/**
+ * 3D formats.
+ */
+typedef enum {
+	XVIDC_3D_FRAME_PACKING = 0,	/**< Frame packing.         */
+	XVIDC_3D_FIELD_ALTERNATIVE,	/**< Field alternative.     */
+	XVIDC_3D_LINE_ALTERNATIVE,	/**< Line alternative.      */
+	XVIDC_3D_SIDE_BY_SIDE_FULL,	/**< Side-by-side (full).   */
+	XVIDC_3D_TOP_AND_BOTTOM_HALF,	/**< Top-and-bottom (half). */
+	XVIDC_3D_SIDE_BY_SIDE_HALF,	/**< Side-by-side (half).   */
+	XVIDC_3D_UNKNOWN
+} XVidC_3DFormat;
+
+/**
+ * 3D Sub-sampling methods.
+ */
+typedef enum {
+	XVIDC_3D_SAMPLING_HORIZONTAL = 0, /**< Horizontal sub-sampling. */
+	XVIDC_3D_SAMPLING_QUINCUNX,	  /**< Quincunx matrix.         */
+	XVIDC_3D_SAMPLING_UNKNOWN
+} XVidC_3DSamplingMethod;
+
+/**
+ * 3D Sub-sampling positions.
+ */
+typedef enum {
+	XVIDC_3D_SAMPPOS_OLOR = 0,	/**< Odd/Left,  Odd/Right.  */
+	XVIDC_3D_SAMPPOS_OLER,		/**< Odd/Left,  Even/Right. */
+	XVIDC_3D_SAMPPOS_ELOR,		/**< Even/Left, Odd/Right.  */
+	XVIDC_3D_SAMPPOS_ELER,		/**< Even/Left, Even/Right. */
+	XVIDC_3D_SAMPPOS_UNKNOWN
+} XVidC_3DSamplingPosition;
+
+/****************************** Type Definitions ******************************/
+
+/**
+ * Video timing structure.
+ */
+typedef struct {
+	u16 HActive;
+	u16 HFrontPorch;
+	u16 HSyncWidth;
+	u16 HBackPorch;
+	u16 HTotal;
+	u8 HSyncPolarity;
+	u16 VActive;
+	u16 F0PVFrontPorch;
+	u16 F0PVSyncWidth;
+	u16 F0PVBackPorch;
+	u16 F0PVTotal;
+	u16 F1VFrontPorch;
+	u16 F1VSyncWidth;
+	u16 F1VBackPorch;
+	u16 F1VTotal;
+	u8 VSyncPolarity;
+} XVidC_VideoTiming;
+
+/**
+ * 3D Sampling info structure.
+ */
+typedef struct {
+	XVidC_3DSamplingMethod   Method;
+	XVidC_3DSamplingPosition Position;
+} XVidC_3DSamplingInfo;
+
+/**
+ * 3D info structure.
+ */
+typedef struct {
+	XVidC_3DFormat		  Format;
+	XVidC_3DSamplingInfo  Sampling;
+} XVidC_3DInfo;
+
+/**
+ * Electro Optical Transfer Function
+ *
+ * Based on CTA861-G
+ */
+typedef enum {
+	/* TG - Traditional Gamma */
+	XVIDC_EOTF_TG_SDR = 0,
+	XVIDC_EOTF_TG_HDR,
+	XVIDC_EOTF_SMPTE2084,
+	XVIDC_EOTF_HLG,
+	XVIDC_EOTF_NUM_SUPPORTED,
+	XVIDC_EOTF_UNKNOWN,
+} XVidC_Eotf;
+
+/**
+ * Video stream structure.
+ */
+typedef struct {
+	XVidC_ColorFormat	  ColorFormatId;
+	XVidC_ColorDepth	  ColorDepth;
+	XVidC_PixelsPerClock  PixPerClk;
+	XVidC_FrameRate		  FrameRate;
+	XVidC_AspectRatio	  AspectRatio;
+	u8			          IsInterlaced;
+	u8			          Is3D;
+	XVidC_3DInfo		  Info_3D;
+	XVidC_VideoMode		  VmId;
+	XVidC_VideoTiming	  Timing;
+	XVidC_Eotf		Eotf;
+	XVidC_ColorStd		ColorStd;
+	XVidC_FrameRate		  BaseFrameRate;
+	XVidC_VideoTiming	  BaseTiming;
+} XVidC_VideoStream;
+
+/**
+ * Video window structure.
+ */
+typedef struct {
+	u32 StartX;
+	u32 StartY;
+	u32 Width;
+	u32 Height;
+} XVidC_VideoWindow;
+
+/**
+ * Video timing mode from the video timing table.
+ */
+typedef struct {
+	XVidC_VideoMode		VmId;
+	char			Name[21];
+	XVidC_FrameRate		FrameRate;
+	XVidC_VideoTiming	Timing;
+} XVidC_VideoTimingMode;
+
+/**
+ * Callback type which represents a custom timer wait handler. This is only
+ * used for Microblaze since it doesn't have a native sleep function. To avoid
+ * dependency on a hardware timer, the default wait functionality is implemented
+ * using loop iterations; this isn't too accurate. Therefore a custom timer
+ * handler is used, the user may implement their own wait implementation.
+ *
+ * @param	TimerPtr is a pointer to the timer instance.
+ * @param	Delay is the duration (msec/usec) to be passed to the timer
+ *		function.
+ *
+*******************************************************************************/
+typedef void (*XVidC_DelayHandler)(void *TimerPtr, u32 Delay);
+
+/**************************** Function Prototypes *****************************/
+
+u32 XVidC_RegisterCustomTimingModes(const XVidC_VideoTimingMode *CustomTable,
+		                            u16 NumElems);
+void XVidC_UnregisterCustomTimingModes(void);
+u64 XVidC_GetPixelClockHzByHVFr(u32 HTotal, u32 VTotal, u8 FrameRate);
+u64 XVidC_GetPixelClockHzByVmId(XVidC_VideoMode VmId);
+XVidC_VideoFormat XVidC_GetVideoFormat(XVidC_VideoMode VmId);
+u8 XVidC_IsInterlaced(XVidC_VideoMode VmId);
+const XVidC_VideoTimingMode* XVidC_GetVideoModeData(XVidC_VideoMode VmId);
+const char *XVidC_GetVideoModeStr(XVidC_VideoMode VmId);
+const char *XVidC_GetFrameRateStr(XVidC_VideoMode VmId);
+const char *XVidC_GetColorFormatStr(XVidC_ColorFormat ColorFormatId);
+XVidC_FrameRate XVidC_GetFrameRate(XVidC_VideoMode VmId);
+const XVidC_VideoTiming* XVidC_GetTimingInfo(XVidC_VideoMode VmId);
+void XVidC_ReportStreamInfo(const XVidC_VideoStream *Stream);
+void XVidC_ReportTiming(const XVidC_VideoTiming *Timing, u8 IsInterlaced);
+const char *XVidC_Get3DFormatStr(XVidC_3DFormat Format);
+u32 XVidC_SetVideoStream(XVidC_VideoStream *VidStrmPtr, XVidC_VideoMode VmId,
+			             XVidC_ColorFormat ColorFormat, XVidC_ColorDepth Bpc,
+			             XVidC_PixelsPerClock Ppc);
+u32 XVidC_Set3DVideoStream(XVidC_VideoStream *VidStrmPtr, XVidC_VideoMode VmId,
+			               XVidC_ColorFormat ColorFormat, XVidC_ColorDepth Bpc,
+			               XVidC_PixelsPerClock Ppc, XVidC_3DInfo *Info3DPtr);
+XVidC_VideoMode XVidC_GetVideoModeId(u32 Width, u32 Height, u32 FrameRate,
+		                             u8 IsInterlaced);
+XVidC_VideoMode XVidC_GetVideoModeIdExtensive(XVidC_VideoTiming *Timing,
+											  u32 FrameRate,
+											  u8 IsInterlaced,
+											  u8 IsExtensive);
+XVidC_VideoMode XVidC_GetVideoModeIdRb(u32 Width, u32 Height, u32 FrameRate,
+		                               u8 IsInterlaced, u8 RbN);
+XVidC_VideoMode XVidC_GetVideoModeIdWBlanking(const XVidC_VideoTiming *Timing,
+		                                      u32 FrameRate, u8 IsInterlaced);
+
+int XVidC_ShowStreamInfo(const XVidC_VideoStream *Stream, char *buff, int buff_size);
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+/*****************************************************************************/
+/**
+ * This macro check if video stream is 3D or 2D.
+ *
+ * @param	VidStreamPtr is a pointer to the XVidC_VideoStream structure.
+ *
+ * @return	3D(1)/2D(0)
+ *
+ * @note	C-style signature:
+ *		u8 XDp_IsStream3D(XVidC_VideoStream *VidStreamPtr)
+ *
+ *****************************************************************************/
+#define XVidC_IsStream3D(VidStreamPtr)       ((VidStreamPtr)->Is3D)
+
+/*************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XVIDC_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvidc_timings_table.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvidc_timings_table.c
@@ -0,0 +1,685 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvidc_timings_table.c
+ * @{
+ *
+ * Contains video timings for various standard resolutions.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als, 01/10/15 Initial release.
+ *       rc
+ * 2.0   als  08/14/15 Added new video timings.
+ * 2.1   als  11/04/15 Fixed video timings for some resolutions.
+ *       rco  02/09/17 Fix c++ compilation warnings
+ * 4.2   jsr  07/08/17 Added new video timings for SDI supported resolutions
+ *       aad  07/10/17 Add XVIDC_VM_3840x2160_60_P_RB video format
+ *       aad  09/05/17 Fixed timings for 1366x768_60_P
+ *       aad  09/05/17 Added 1366x768_60_P_RB
+ * 4.4   eb   09/04/18 Fixed timings for 1280x720_24_P, 1280x720_25_P,
+ *                         1280x720_30_P
+ * 4.5	 jsr  07/03/18 Added timing for new video mode XVIDC_VM_720x486_60_I
+ * 4.5   mmo  02/14/19 Added 5k, 8k, 10k and Low Resolution with 200Hz, 240Hz
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xvidc.h"
+
+/**************************** Variable Definitions ****************************/
+
+/**
+ * This table contains the main stream attributes for various standard
+ * resolutions. Each entry is of the format:
+ * 1) ID: XVIDC_VM_<HRES>x<VRES>_<FRAME RATE (HZ)>_<P|I>(_RB = Reduced Blanking)
+ * 2) Resolution naming: "<HRES>x<VRES>@<FRAME RATE (HZ)>"
+ * 3) Frame rate: XVIDC_FR_<FRAME RATE (HZ)>
+ * 4) Video timing structure:
+ *    1) Horizontal active resolution (pixels)
+ *    2) Horizontal front porch (pixels)
+ *    3) Horizontal sync width (pixels)
+ *    4) Horizontal back porch (pixels)
+ *    5) Horizontal total (pixels)
+ *    6) Horizontal sync polarity (0=negative|1=positive)
+ *    7) Vertical active resolution (lines)
+ *    8) Frame 0: Vertical front porch (lines)
+ *    9) Frame 0: Vertical sync width (lines)
+ *    10) Frame 0: Vertical back porch (lines)
+ *    11) Frame 0: Vertical total (lines)
+ *    12) Frame 1: Vertical front porch (lines)
+ *    13) Frame 1: Vertical sync width (lines)
+ *    14) Frame 1: Vertical back porch (lines)
+ *    15) Frame 1: Vertical total (lines)
+ *    16) Vertical sync polarity (0=negative|1=positive)
+ */
+#ifdef __cplusplus
+extern "C"
+#endif
+const XVidC_VideoTimingMode XVidC_VideoTimingModes[XVIDC_VM_NUM_SUPPORTED] =
+{
+	/* Interlaced modes. */
+	{ XVIDC_VM_720x480_60_I, "720x480@60Hz (I)", XVIDC_FR_60HZ,
+		{720, 19, 62, 57, 858, 0,
+		240, 4, 3, 15, 262, 5, 3, 15, 263, 0} },
+	{ XVIDC_VM_720x486_60_I, "720x486@60Hz (I)", XVIDC_FR_60HZ,
+		{720, 19, 62, 57, 858, 0,
+		243, 1, 3, 15, 262, 2, 3, 15, 263, 0} },
+	{ XVIDC_VM_720x576_50_I, "720x576@50Hz (I)", XVIDC_FR_50HZ,
+		{720, 12, 63, 69, 864, 0,
+		288, 2, 3, 19, 312, 3, 3, 19, 313, 0} },
+	{ XVIDC_VM_1440x480_60_I, "1440x480@60Hz (I)", XVIDC_FR_60HZ,
+		{1440, 38, 124, 114, 1716, 0,
+		240, 4, 3, 15, 262, 5, 3, 15, 263, 0} },
+	{ XVIDC_VM_1440x480_120_I, "1440x480@120Hz (I)", XVIDC_FR_120HZ,
+		{1440, 38, 124, 114, 1716, 0,
+		240, 4, 3, 15, 262, 5, 3, 15, 263, 0} },
+	{ XVIDC_VM_1440x480_240_I, "1440x480@240Hz (I)", XVIDC_FR_240HZ,
+		{1440, 38, 124, 114, 1716, 0,
+		240, 4, 3, 15, 262, 5, 3, 15, 263, 0} },
+	{ XVIDC_VM_1440x576_50_I, "1440x576@50Hz (I)", XVIDC_FR_50HZ,
+		{1440, 24, 126, 138, 1728, 0,
+		288, 2, 3, 19, 312, 3, 3, 19, 313, 0} },
+	{ XVIDC_VM_1440x576_100_I, "1440x576@100Hz (I)", XVIDC_FR_100HZ,
+		{1440, 24, 126, 138, 1728, 0,
+		288, 2, 3, 19, 312, 3, 3, 19, 313, 0} },
+	{ XVIDC_VM_1440x576_200_I, "1440x576@200Hz (I)", XVIDC_FR_200HZ,
+		{1440, 24, 126, 138, 1728, 0,
+		288, 2, 3, 19, 312, 3, 3, 19, 313, 0} },
+	{ XVIDC_VM_1920x1080_48_I, "1920x1080@48Hz (I)", XVIDC_FR_48HZ,
+		{1920, 371, 88, 371, 2750, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_1920x1080_50_I, "1920x1080@50Hz (I)", XVIDC_FR_50HZ,
+		{1920, 528, 44, 148, 2640, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_1920x1080_60_I, "1920x1080@60Hz (I)", XVIDC_FR_60HZ,
+		{1920, 88, 44, 148, 2200, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_1920x1080_96_I, "1920x1080@96Hz (I)", XVIDC_FR_96HZ,
+		{1920, 371, 88, 371, 2750, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_1920x1080_100_I, "1920x1080@100Hz (I)", XVIDC_FR_100HZ,
+		{1920, 528, 44, 148, 2640, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_1920x1080_120_I, "1920x1080@120Hz (I)", XVIDC_FR_120HZ,
+		{1920, 88, 44, 148, 2200, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2048x1080_48_I, "2048x1080@48Hz (I)", XVIDC_FR_48HZ,
+		{2048, 329, 44, 329, 2750, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2048x1080_50_I, "2048x1080@50Hz (I)", XVIDC_FR_50HZ,
+		{2048, 274, 44, 274, 2640, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2048x1080_60_I, "2048x1080@60Hz (I)", XVIDC_FR_60HZ,
+		{2048, 66, 20, 66, 2200, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2048x1080_96_I, "2048x1080@96Hz (I)", XVIDC_FR_96HZ,
+		{2048, 329, 44, 329, 2750, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2048x1080_100_I, "2048x1080@100Hz (I)", XVIDC_FR_100HZ,
+		{2048, 274, 44, 274, 2640, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2048x1080_120_I, "2048x1080@120Hz (I)", XVIDC_FR_120HZ,
+		{2048, 66, 20, 66, 2200, 1,
+		540, 2, 5, 15, 562, 3, 5, 15, 563, 1} },
+	{ XVIDC_VM_2880x480_60_I, "2880x480@60Hz (I)", XVIDC_FR_60HZ,
+		{2880, 76, 248, 228, 3432, 0,
+		240, 4, 3, 15, 262, 5, 3, 15, 263, 0} },
+	{XVIDC_VM_2880x576_50_I, "2880x576@50Hz (I)", XVIDC_FR_50HZ,
+		{2880, 48, 252, 276, 3456, 0,
+		576, 2, 3, 19, 312, 2, 3, 19, 313, 0} },
+
+	/* Progressive modes. */
+	{ XVIDC_VM_640x350_85_P, "640x350@85Hz", XVIDC_FR_85HZ,
+		{640, 32, 64, 96, 832, 1,
+		350, 32, 3, 60, 445, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_640x480_60_P, "640x480@60Hz", XVIDC_FR_60HZ,
+		{640, 8+8, 96, 40+8, 800, 0,
+		480, 2+8, 2, 25+8, 525, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_640x480_72_P, "640x480@72Hz", XVIDC_FR_72HZ,
+		{640, 8+16, 40, 120+8, 832, 0,
+		480, 8+1, 3, 20+8, 520, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_640x480_75_P, "640x480@75Hz", XVIDC_FR_75HZ,
+		{640, 16, 64, 120, 840, 0,
+		480, 1, 3, 16, 500, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_640x480_85_P, "640x480@85Hz", XVIDC_FR_85HZ,
+		{640, 56, 56, 80, 832, 0,
+		480, 1, 3, 25, 509, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_720x400_85_P, "720x400@85Hz", XVIDC_FR_85HZ,
+		{720, 36, 72, 108, 936, 0,
+		400, 1, 3, 42, 446, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_720x480_60_P, "720x480@60Hz", XVIDC_FR_60HZ,
+		{720, 16, 62, 60, 858, 0,
+		480, 9, 6, 30, 525, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_720x480_120_P, "720x480@120Hz", XVIDC_FR_120HZ,
+		{720, 16, 62, 60, 858, 0,
+		480, 9, 6, 30, 525, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_720x480_240_P, "720x480@240Hz", XVIDC_FR_240HZ,
+		{720, 16, 62, 60, 858, 0,
+		480, 9, 6, 30, 525, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_720x576_50_P, "720x576@50Hz", XVIDC_FR_50HZ,
+		{720, 12, 64, 68, 864, 0,
+		576, 5, 5, 39, 625, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_720x576_100_P, "720x576@100Hz", XVIDC_FR_100HZ,
+		{720, 12, 64, 68, 864, 0,
+		576, 5, 5, 39, 625, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_720x576_200_P, "720x576@200Hz", XVIDC_FR_200HZ,
+		{720, 12, 64, 68, 864, 0,
+		576, 5, 5, 39, 625, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_800x600_56_P, "800x600@56Hz", XVIDC_FR_56HZ,
+		{800, 24, 72, 128, 1024, 1,
+		600, 1, 2, 22, 625, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_800x600_60_P, "800x600@60Hz", XVIDC_FR_60HZ,
+		{800, 40, 128, 88, 1056, 1,
+		600, 1, 4, 23, 628, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_800x600_72_P, "800x600@72Hz", XVIDC_FR_72HZ,
+		{800, 56, 120, 64, 1040, 1,
+		600, 37, 6, 23, 666, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_800x600_75_P, "800x600@75Hz", XVIDC_FR_75HZ,
+		{800, 16, 80, 160, 1056, 1,
+		600, 1, 3, 21, 625, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_800x600_85_P, "800x600@85Hz", XVIDC_FR_85HZ,
+		{800, 32, 64, 152, 1048, 1,
+		600, 1, 3, 27, 631, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_800x600_120_P_RB, "800x600@120Hz (RB)", XVIDC_FR_120HZ,
+		{800, 48, 32, 80, 960, 1,
+		600, 3, 4, 29, 636, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_848x480_60_P, "848x480@60Hz", XVIDC_FR_60HZ,
+		{848, 16, 112, 112, 1088, 1,
+		480, 6, 8, 23, 517, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1024x768_60_P, "1024x768@60Hz", XVIDC_FR_60HZ,
+		{1024, 24, 136, 160, 1344, 0,
+		768, 3, 6, 29, 806, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1024x768_70_P, "1024x768@70Hz", XVIDC_FR_70HZ,
+		{1024, 24, 136, 144, 1328, 0,
+		768, 3, 6, 29, 806, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1024x768_75_P, "1024x768@75Hz", XVIDC_FR_75HZ,
+		{1024, 16, 96, 176, 1312, 1,
+		768, 1, 3, 28, 800, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1024x768_85_P, "1024x768@85Hz", XVIDC_FR_85HZ,
+		{1024, 48, 96, 208, 1376, 1,
+		768, 1, 3, 36, 808, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1024x768_120_P_RB, "1024x768@120Hz (RB)", XVIDC_FR_120HZ,
+		{1024, 48, 32, 80, 1184, 1,
+		768, 3, 4, 38, 813, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1152x864_75_P, "1152x864@75Hz", XVIDC_FR_75HZ,
+		{1152, 64, 128, 256, 1600, 1,
+		864, 1, 3, 32, 900, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_24_P, "1280x720@24Hz", XVIDC_FR_24HZ,
+		{1280, 1760, 40, 220, 3300, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_25_P, "1280x720@25Hz", XVIDC_FR_25HZ,
+		{1280, 2420, 40, 220, 3960, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_30_P, "1280x720@30Hz", XVIDC_FR_30HZ,
+		{1280, 1760, 40, 220, 3300, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_50_P, "1280x720@50Hz", XVIDC_FR_50HZ,
+		{1280, 440, 40, 220, 1980, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_60_P, "1280x720@60Hz", XVIDC_FR_60HZ,
+		{1280, 110, 40, 220, 1650, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_100_P, "1280x720@100Hz", XVIDC_FR_100HZ,
+		{1280, 440, 40, 220, 1980, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x720_120_P, "1280x720@120Hz", XVIDC_FR_120HZ,
+		{1280, 110, 40, 220, 1650, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x768_60_P, "1280x768@60Hz", XVIDC_FR_60HZ,
+		{1280, 64, 128, 192, 1664, 0,
+		768, 3, 7, 20, 798, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x768_60_P_RB, "1280x768@60Hz (RB)", XVIDC_FR_60HZ,
+		{1280, 48, 32, 80, 1440, 1,
+		768, 3, 7, 12, 790, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1280x768_75_P, "1280x768@75Hz", XVIDC_FR_75HZ,
+		{1280, 80, 128, 208, 1696, 0,
+		768, 3, 7, 27, 805, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x768_85_P, "1280x768@85Hz", XVIDC_FR_85HZ,
+		{1280, 80, 136, 216, 1712, 0,
+		768, 3, 7, 31, 809, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x768_120_P_RB, "1280x768@120Hz (RB)", XVIDC_FR_120HZ,
+		{1280, 48, 32, 80, 1440, 1,
+		768, 3, 7, 35, 813, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1280x800_60_P, "1280x800@60Hz", XVIDC_FR_60HZ,
+		{1280, 72, 128, 200, 1680, 0,
+		800, 3, 6, 22, 831, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x800_60_P_RB, "1280x800@60Hz (RB)", XVIDC_FR_60HZ,
+		{1280, 48, 32, 80, 1440, 1,
+		800, 3, 6, 14, 823, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1280x800_75_P, "1280x800@75Hz", XVIDC_FR_75HZ,
+		{1280, 80, 128, 208, 1696, 0,
+		800, 3, 6, 29, 838, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x800_85_P, "1280x800@85Hz", XVIDC_FR_85HZ,
+		{1280, 80, 136, 216, 1712, 0,
+		800, 3, 6, 34, 843, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x800_120_P_RB, "1280x800@120Hz (RB)", XVIDC_FR_120HZ,
+		{1280, 48, 32, 80, 1440, 1,
+		800, 3, 6, 38, 847, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1280x960_60_P, "1280x960@60Hz", XVIDC_FR_60HZ,
+		{1280, 96, 112, 312, 1800, 1,
+		960, 1, 3, 36, 1000, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x960_85_P, "1280x960@85Hz", XVIDC_FR_85HZ,
+		{1280, 64, 160, 224, 1728, 1,
+		960, 1, 3, 47, 1011, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x960_120_P_RB, "1280x960@120Hz (RB)", XVIDC_FR_120HZ,
+		{1280, 48, 32, 80, 1440, 1,
+		960, 3, 4, 50, 1017, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1280x1024_60_P, "1280x1024@60Hz", XVIDC_FR_60HZ,
+		{1280, 48, 112, 248, 1688, 1,
+		1024, 1, 3, 38, 1066, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x1024_75_P, "1280x1024@75Hz", XVIDC_FR_75HZ,
+		{1280, 16, 144, 248, 1688, 1,
+		1024, 1, 3, 38, 1066, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x1024_85_P, "1280x1024@85Hz", XVIDC_FR_85HZ,
+		{1280, 64, 160, 224, 1728, 1,
+		1024, 1, 3, 44, 1072, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1280x1024_120_P_RB, "1280x1024@120Hz (RB)", XVIDC_FR_120HZ,
+		{1280, 48, 32, 80, 1440, 1,
+		1024, 3, 7, 50, 1084, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1360x768_60_P, "1360x768@60Hz", XVIDC_FR_60HZ,
+		{1360, 64, 112, 256, 1792, 1,
+		768, 3, 6, 18, 795, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1360x768_120_P_RB, "1360x768@120Hz (RB)", XVIDC_FR_120HZ,
+		{1360, 48, 32, 80, 1520, 1,
+		768, 3, 5, 37, 813, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1366x768_60_P, "1366x768@60Hz", XVIDC_FR_60HZ,
+		{1366, 70, 143, 213, 1792, 1,
+		768, 3, 3, 24, 798, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1366x768_60_P_RB, "1366x768@60Hz (RB)", XVIDC_FR_60HZ,
+		{1366, 14, 56, 64, 1500, 1,
+		768, 1, 3, 28, 800, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1400x1050_60_P, "1400x1050@60Hz", XVIDC_FR_60HZ,
+		{1400, 88, 144, 232, 1864, 0,
+		1050, 3, 4, 32, 1089, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1400x1050_60_P_RB, "1400x1050@60Hz (RB)", XVIDC_FR_60HZ,
+		{1400, 48, 32, 80, 1560, 1,
+		1050, 3, 4, 23, 1080, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1400x1050_75_P, "1400x1050@75Hz", XVIDC_FR_75HZ,
+		{1400, 104, 144, 248, 1896, 0,
+		1050, 3, 4, 42, 1099, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1400x1050_85_P, "1400x1050@85Hz", XVIDC_FR_85HZ,
+		{1400, 104, 152, 256, 1912, 0,
+		1050, 3, 4, 48, 1105, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1400x1050_120_P_RB, "1400x1050@120Hz (RB)", XVIDC_FR_120HZ,
+		{1400, 48, 32, 80, 1560, 1,
+		1050, 3, 4, 55, 1112, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1440x240_60_P, "1440x240@60Hz", XVIDC_FR_60HZ,
+		{1440, 38, 124, 114, 1716, 0,
+		240, 4, 3, 15, 262, 0, 0, 0, 0, 1} },
+	{XVIDC_VM_1440x288_50_P, "1440x288@50Hz", XVIDC_FR_50HZ,
+		{1440, 24, 126, 138, 1728, 0,
+		288, 3, 3, 19, 313, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1440x480_60_P, "1440x240@60Hz", XVIDC_FR_60HZ,
+		{1440, 32, 124, 120, 1716, 0,
+		480, 9, 6, 30, 525, 0, 0, 0, 0, 0} },
+	{XVIDC_VM_1440x576_50_P, "1440x576@50Hz", XVIDC_FR_50HZ,
+		{1440, 24, 128, 136, 1728, 0,
+		576, 5, 5, 39, 625, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1440x900_60_P, "1440x900@60Hz", XVIDC_FR_60HZ,
+		{1440, 80, 152, 232, 1904, 0,
+		900, 3, 6, 25, 934, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1440x900_60_P_RB, "1440x900@60Hz (RB)", XVIDC_FR_60HZ,
+		{1440, 48, 32, 80, 1600, 1,
+		900, 3, 6, 17, 926, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1440x900_75_P, "1440x900@75Hz", XVIDC_FR_75HZ,
+		{1440, 96, 152, 248, 1936, 0,
+		900, 3, 6, 33, 942, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1440x900_85_P, "1440x900@85Hz", XVIDC_FR_85HZ,
+		{1440, 104, 152, 256, 1952, 0,
+		900, 3, 6, 39, 948, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1440x900_120_P_RB, "1440x900@120Hz (RB)", XVIDC_FR_120HZ,
+		{1440, 48, 32, 80, 1600, 1,
+		900, 3, 6, 44, 953, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1600x1200_60_P, "1600x1200@60Hz", XVIDC_FR_60HZ,
+		{1600, 64, 192, 304, 2160, 1,
+		1200, 1, 3, 46, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1600x1200_65_P, "1600x1200@65Hz", XVIDC_FR_65HZ,
+		{1600, 64, 192, 304, 2160, 1,
+		1200, 1, 3, 46, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1600x1200_70_P, "1600x1200@70Hz", XVIDC_FR_70HZ,
+		{1600, 64, 192, 304, 2160, 1,
+		1200, 1, 3, 46, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1600x1200_75_P, "1600x1200@75Hz", XVIDC_FR_75HZ,
+		{1600, 64, 192, 304, 2160, 1,
+		1200, 1, 3, 46, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1600x1200_85_P, "1600x1200@85Hz", XVIDC_FR_85HZ,
+		{1600, 64, 192, 304, 2160, 1,
+		1200, 1, 3, 46, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1600x1200_120_P_RB, "1600x1200@120Hz (RB)", XVIDC_FR_120HZ,
+		{1600, 48, 32, 80, 1760, 1,
+		1200, 3, 4, 64, 1271, 0, 0, 0, 0, 0} },
+	{XVIDC_VM_1680x720_24_P, "1680x720@24Hz", XVIDC_FR_24HZ,
+		{1680, 1360, 40, 220, 3300, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 0} },
+	{XVIDC_VM_1680x720_25_P, "1680x720@25Hz", XVIDC_FR_25HZ,
+		{1680, 1228, 40, 220, 3168, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 0} },
+	{XVIDC_VM_1680x720_30_P, "1680x720@30Hz", XVIDC_FR_30HZ,
+		{1680, 700, 40, 220, 2640, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1680x720_50_P, "1680x720@50Hz", XVIDC_FR_50HZ,
+		{1680, 260, 40, 220, 2200, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x720_60_P, "1680x720@60Hz", XVIDC_FR_60HZ,
+		{1680, 260, 40, 220, 2200, 1,
+		720, 5, 5, 20, 750, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x720_100_P, "1680x720@100Hz", XVIDC_FR_100HZ,
+		{1680, 60, 40, 220, 2000, 1,
+		720, 5, 5, 95, 825, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x720_120_P, "1680x720@120Hz", XVIDC_FR_120HZ,
+		{1680, 60, 40, 220, 2000, 1,
+		720, 5, 5, 95, 825, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x1050_50_P, "1680x1050@50Hz", XVIDC_FR_50HZ,
+		{1680, 88, 176, 264, 2208, 0,
+		1050, 3, 6, 24, 1083, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x1050_60_P, "1680x1050@60Hz", XVIDC_FR_60HZ,
+		{1680, 104, 176, 280, 2240, 0,
+		1050, 3, 6, 30, 1089, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x1050_60_P_RB, "1680x1050@60Hz (RB)", XVIDC_FR_60HZ,
+		{1680, 48, 32, 80, 1840, 1,
+		1050, 3, 6, 21, 1080, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1680x1050_75_P, "1680x1050@75Hz", XVIDC_FR_75HZ,
+		{1680, 120, 176, 296, 2272, 0,
+		1050, 3, 6, 40, 1099, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x1050_85_P, "1680x1050@85Hz", XVIDC_FR_85HZ,
+		{1680, 128, 176, 304, 2288, 0,
+		1050, 3, 6, 46, 1105, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1680x1050_120_P_RB, "1680x1050@120Hz (RB)", XVIDC_FR_120HZ,
+		{1680, 48, 32, 80, 1840, 1,
+		1050, 3, 6, 53, 1112, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1792x1344_60_P, "1792x1344@60Hz", XVIDC_FR_60HZ,
+		{1792, 128, 200, 328, 2448, 0,
+		1344, 1, 3, 46, 1394, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1792x1344_75_P, "1792x1344@75Hz", XVIDC_FR_75HZ,
+		{1792, 96, 216, 352, 2456, 0,
+		1344, 1, 3, 69, 1417, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1792x1344_120_P_RB, "1792x1344@120Hz (RB)", XVIDC_FR_120HZ,
+		{1792, 48, 32, 80, 1952, 1,
+		1344, 3, 4, 72, 1423, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1856x1392_60_P, "1856x1392@60Hz", XVIDC_FR_60HZ,
+		{1856, 96, 224, 352, 2528, 0,
+		1392, 1, 3, 43, 1439, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1856x1392_75_P, "1856x1392@75Hz", XVIDC_FR_75HZ,
+		{1856, 128, 224, 352, 2560, 0,
+		1392, 1, 3, 104, 1500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1856x1392_120_P_RB, "1856x1392@120Hz (RB)", XVIDC_FR_120HZ,
+		{1856, 48, 32, 80, 2016, 1,
+		1392, 3, 4, 75, 1474, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1920x1080_24_P, "1920x1080@24Hz", XVIDC_FR_24HZ,
+		{1920, 638, 44, 148, 2750, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_25_P, "1920x1080@25Hz", XVIDC_FR_25HZ,
+		{1920, 528, 44, 148, 2640, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_30_P, "1920x1080@30Hz", XVIDC_FR_30HZ,
+		{1920, 88, 44, 148, 2200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_48_P, "1920x1080@48Hz", XVIDC_FR_48HZ,
+		{1920, 638, 44, 148, 2750, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_50_P, "1920x1080@50Hz", XVIDC_FR_50HZ,
+		{1920, 528, 44, 148, 2640, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_60_P, "1920x1080@60Hz", XVIDC_FR_60HZ,
+		{1920, 88, 44, 148, 2200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_100_P, "1920x1080@100Hz", XVIDC_FR_100HZ,
+		{1920, 528, 44, 148, 2640, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1080_120_P, "1920x1080@120Hz", XVIDC_FR_120HZ,
+		{1920, 88, 44, 148, 2200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1200_60_P, "1920x1200@60Hz", XVIDC_FR_60HZ,
+		{1920, 136, 200, 336, 2592, 0,
+		1200, 3, 6, 36, 1245, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1200_60_P_RB, "1920x1200@60Hz (RB)", XVIDC_FR_60HZ,
+		{1920, 48, 32, 80, 2080, 1,
+		1200, 3, 6, 26, 1235, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1920x1200_75_P, "1920x1200@75Hz", XVIDC_FR_75HZ,
+		{1920, 136, 208, 344, 2608, 0,
+		1200, 3, 6, 46, 1255, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1200_85_P, "1920x1200@85Hz", XVIDC_FR_85HZ,
+		{1920, 144, 208, 352, 2624, 0,
+		1200, 3, 6, 53, 1262, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1200_120_P_RB, "1920x1200@120Hz (RB)", XVIDC_FR_120HZ,
+		{1920, 48, 32, 80, 2080, 1,
+		1200, 3, 6, 62, 1271, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1920x1440_60_P, "1920x1440@60Hz", XVIDC_FR_60HZ,
+		{1920, 128, 208, 344, 2600, 0,
+		1440, 1, 3, 56, 1500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1440_75_P, "1920x1440@75Hz", XVIDC_FR_75HZ,
+		{1920, 144, 224, 352, 2640, 0,
+		1440, 1, 3, 56, 1500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_1920x1440_120_P_RB, "1920x1440@120Hz (RB)", XVIDC_FR_120HZ,
+		{1920, 48, 32, 80, 2080, 1,
+		1440, 3, 4, 78, 1525, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_1920x2160_60_P, "1920x2160@60Hz", XVIDC_FR_60HZ,
+		{1920, 88, 44, 148, 2200, 1,
+		2160, 20, 10, 60, 2250, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_2048x1080_24_P, "2048x1080@24Hz", XVIDC_FR_24HZ,
+		{2048, 510, 44, 148, 2750, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_25_P, "2048x1080@25Hz", XVIDC_FR_25HZ,
+		{2048, 400, 44, 148, 2640, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_30_P, "2048x1080@30Hz", XVIDC_FR_30HZ,
+		{2048, 66, 20, 66, 2200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_48_P, "2048x1080@48Hz", XVIDC_FR_48HZ,
+		{2048, 510, 44, 148, 2750, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_50_P, "2048x1080@50Hz", XVIDC_FR_50HZ,
+		{2048, 400, 44, 148, 2640, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_60_P, "2048x1080@60Hz", XVIDC_FR_60HZ,
+		{2048, 88, 44, 20, 2200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_100_P, "2048x1080@100Hz", XVIDC_FR_100HZ,
+		{2048, 528, 44, 148, 2640, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2048x1080_120_P, "2048x1080@120Hz", XVIDC_FR_120HZ,
+		{2048, 88, 44, 148, 2200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_24_P, "2560x1080@24Hz", XVIDC_FR_24HZ,
+		{2560, 998, 44, 148, 3750, 1,
+		1080, 4, 5, 11, 1100, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_25_P, "2560x1080@25Hz", XVIDC_FR_25HZ,
+		{2560, 448, 44, 148, 3200, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_30_P, "2560x1080@30Hz", XVIDC_FR_30HZ,
+		{2560, 768, 44, 148, 3520, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_48_P, "2560x1080@48Hz", XVIDC_FR_48HZ,
+		{2560, 998, 44, 148, 3750, 1,
+		1080, 4, 5, 11, 1100, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_50_P, "2560x1080@50Hz", XVIDC_FR_50HZ,
+		{2560, 548, 44, 148, 3300, 1,
+		1080, 4, 5, 36, 1125, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_60_P, "2560x1080@60Hz", XVIDC_FR_60HZ,
+		{2560, 248, 44, 148, 3000, 1,
+		1080, 4, 5, 11, 1100, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_100_P, "2560x1080@100Hz", XVIDC_FR_100HZ,
+		{2560, 218, 44, 148, 2970, 1,
+		1080, 4, 5, 161, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1080_120_P, "2560x1080@120Hz", XVIDC_FR_120HZ,
+		{2560, 548, 44, 148, 3300, 1,
+		1080, 4, 5, 161, 1250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1600_60_P, "2560x1600@60Hz", XVIDC_FR_60HZ,
+		{2560, 192, 280, 472, 3504, 0,
+		1600, 3, 6, 49, 1658, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1600_60_P_RB, "2560x1600@60Hz (RB)", XVIDC_FR_60HZ,
+		{2560, 48, 32, 80, 2720, 1,
+		1600, 3, 6, 37, 1646, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_2560x1600_75_P, "2560x1600@75Hz", XVIDC_FR_75HZ,
+		{2560, 208, 280, 488, 3536, 0,
+		1600, 3, 6, 63, 1672, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1600_85_P, "2560x1600@85Hz", XVIDC_FR_85HZ,
+		{2560, 208, 280, 488, 3536, 0,
+		1600, 3, 6, 73, 1682, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2560x1600_120_P_RB, "2560x1600@120Hz (RB)", XVIDC_FR_120HZ,
+		{2560, 48, 32, 80, 2720, 1,
+		1600, 3, 6, 85, 1694, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_2880x240_60_P, "2880x240@60Hz", XVIDC_FR_60HZ,
+		{2880, 76, 248, 228, 3432, 0,
+		240, 14, 3, 4, 262, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_2880x288_50_P, "2880x288@50Hz", XVIDC_FR_50HZ,
+		{2880, 48, 252, 276, 3456, 0,
+		288, 3, 3, 19, 313, 0, 0, 0, 0, 0} },
+	{XVIDC_VM_2880x480_60_P, "2880x480@60Hz", XVIDC_FR_60HZ,
+		{2880, 64, 248, 240, 3432, 0,
+		480, 9, 6, 30, 525, 0, 0, 0, 0, 0} },
+	{XVIDC_VM_2880x576_50_P, "2880x576@50Hz", XVIDC_FR_50HZ,
+		{2880, 48, 256, 272, 3456, 0,
+		576, 5, 5, 39, 625, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_3840x2160_24_P, "3840x2160@24Hz", XVIDC_FR_24HZ,
+		{3840, 1276, 88, 296, 5500, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_25_P, "3840x2160@25Hz", XVIDC_FR_25HZ,
+		{3840, 1056, 88, 296, 5280, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_30_P, "3840x2160@30Hz", XVIDC_FR_30HZ,
+		{3840, 176, 88, 296, 4400, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_48_P, "3840x2160@48Hz", XVIDC_FR_48HZ,
+		{3840, 1276, 88, 296, 5500, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_50_P, "3840x2160@50Hz", XVIDC_FR_50HZ,
+		{3840, 1056, 88, 296, 5280, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_60_P, "3840x2160@60Hz", XVIDC_FR_60HZ,
+		{3840, 176, 88, 296, 4400, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_60_P_RB, "3840x2160@60Hz (RB)", XVIDC_FR_60HZ,
+		{3840, 48, 32, 80, 4000, 1,
+		2160, 3, 5, 54, 2222, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_3840x2160_100_P, "3840x2160@100Hz", XVIDC_FR_100HZ,
+		{3840, 1056, 88, 296, 5280, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_3840x2160_120_P, "3840x2160@120Hz", XVIDC_FR_120HZ,
+		{3840, 176, 88, 296, 4400, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_24_P, "4096x2160@24Hz", XVIDC_FR_24HZ,
+		{4096, 1020, 88, 296, 5500, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_25_P, "4096x2160@25Hz", XVIDC_FR_25HZ,
+		{4096, 968, 88, 128, 5280, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_30_P, "4096x2160@30Hz", XVIDC_FR_30HZ,
+		{4096, 88, 88, 128, 4400, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_48_P, "4096x2160@48Hz", XVIDC_FR_48HZ,
+		{4096, 1020, 88, 296, 5500, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_50_P, "4096x2160@50Hz", XVIDC_FR_50HZ,
+		{4096, 968, 88, 128, 5280, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_60_P, "4096x2160@60Hz", XVIDC_FR_60HZ,
+		{4096, 88, 88, 128, 4400, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_60_P_RB, "4096x2160@60Hz (RB)", XVIDC_FR_60HZ,
+		{4096, 8, 32, 40, 4176, 1,
+		2160, 48, 8, 6, 2222, 0, 0, 0, 0, 0} },
+	{ XVIDC_VM_4096x2160_100_P, "4096x2160@100Hz", XVIDC_FR_100HZ,
+		{4096, 800, 88, 296, 5280, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_4096x2160_120_P, "4096x2160@120Hz", XVIDC_FR_120HZ,
+		{4096, 88, 88, 128, 4400, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_24_P, "5120x2160@24Hz", XVIDC_FR_24HZ,
+		{5120, 1996, 88, 296, 7500, 1,
+		2160, 8, 10, 22, 2200, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_25_P, "5120x2160@25Hz", XVIDC_FR_25HZ,
+		{5120, 1696, 88, 296, 7200, 1,
+		2160, 8, 10, 22, 2200, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_30_P, "5120x2160@30Hz", XVIDC_FR_30HZ,
+		{5120, 664,  88, 128, 6000, 1,
+		2160, 8, 10, 22, 2200, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_48_P, "5120x2160@48Hz", XVIDC_FR_48HZ,
+		{5120, 746,  88, 296, 6250, 1,
+		2160, 8, 10, 297, 2475, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_50_P, "5120x2160@50Hz", XVIDC_FR_50HZ,
+		{5120, 1096, 88, 296, 6600, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_60_P, "5120x2160@60Hz", XVIDC_FR_60HZ,
+		{5120, 164,  88, 128, 5500, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_100_P, "5120x2160@100Hz", XVIDC_FR_100HZ,
+		{5120, 1096, 88, 296, 6600, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_5120x2160_120_P, "5120x2160@120Hz", XVIDC_FR_120HZ,
+		{5120, 164, 88, 128, 5500, 1,
+		2160, 8, 10, 72, 2250, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_24_P, "7680x4320@24Hz", XVIDC_FR_24HZ,
+		{7680, 2552, 176, 592, 11000, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_25_P, "7680x4320@25Hz", XVIDC_FR_25HZ,
+		{7680, 2352, 176, 592, 10800, 1,
+		4320, 16, 20, 44,  4400, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_30_P, "7680x4320@30Hz", XVIDC_FR_30HZ,
+		{7680, 552, 176, 592, 9000, 1,
+		4320, 16, 20, 44, 4400, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_48_P, "7680x4320@48Hz", XVIDC_FR_48HZ,
+		{7680, 2552, 176, 592, 11000, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_50_P, "7680x4320@50Hz", XVIDC_FR_50HZ,
+		{7680, 2352, 176, 592, 10800, 1,
+		4320, 16, 20, 44,  4400, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_60_P, "7680x4320@60Hz", XVIDC_FR_60HZ,
+		{7680, 552, 176, 592, 9000, 1,
+		4320, 16, 20, 44,  4400, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_100_P, "7680x4320@100Hz" , XVIDC_FR_100HZ,
+		{7680, 2112, 176, 592, 10560, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_7680x4320_120_P, "7680x4320@120Hz" , XVIDC_FR_120HZ,
+		{7680, 352, 176, 592, 8800, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_24_P, "10240x4320@24Hz", XVIDC_FR_24HZ,
+		{10240, 1492, 176, 592, 12500, 1,
+		4320, 16, 20, 594, 4950, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_25_P, "10240x4320@25Hz", XVIDC_FR_25HZ,
+		{10240, 2492, 176, 592, 13500, 1,
+		4320, 16, 20, 44, 4400, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_30_P, "10240x4320@30Hz", XVIDC_FR_30HZ,
+		{10240, 288, 176, 296, 11000, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_48_P, "10240x4320@48Hz", XVIDC_FR_48HZ,
+		{10240, 1492, 176, 592, 12500, 1,
+		4320, 16, 20, 594, 4950, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_50_P, "10240x4320@50Hz", XVIDC_FR_50HZ,
+		{10240, 2492, 176, 592, 13500, 1,
+		4320, 16, 20, 44, 4400, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_60_P, "10240x4320@60Hz", XVIDC_FR_60HZ,
+		{10240, 288, 176, 296, 11000, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_100_P, "10240x4320@100Hz", XVIDC_FR_100HZ,
+		{10240, 2192, 176, 592, 13200, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+	{ XVIDC_VM_10240x4320_120_P, "10240x4320@120Hz", XVIDC_FR_120HZ,
+		{10240, 288, 176, 296, 11000, 1,
+		4320, 16, 20, 144, 4500, 0, 0, 0, 0, 1} },
+};
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy.c
@@ -0,0 +1,1785 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy.c
+ *
+ * Contains a minimal set of functions for the XVphy driver that allow access
+ * to all of the Video PHY core's functionality. See xvphy.h for a detailed
+ * description of the driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als, 10/19/15 Initial release.
+ *       gm
+ * 1.1   gm   02/01/16 Added GTPE2 and GTHE4 support
+ *                     Added more events to XVphy_LogEvent definitions.
+ *                     Added TxBufferBypass in XVphy_Config structure.
+ *                     Added XVphy_SetDefaultPpc and XVphy_SetPpc functions.
+ *       als           Added XVphy_GetLineRateHz function.
+ *       gm   20/04/16 Added XVphy_GetRcfgChId function
+ * 1.2   gm            Added HdmiFastSwitch in XVphy_Config
+ *                     Fixed bug in XVphy_IsPllLocked function
+ *                     Changed EffectiveAddr datatype in XVphy_CfgInitialize
+ *                       to UINTPTR
+ *                     Used usleep API instead of MB_Sleep API
+ *                     Fixed Null pointer dereference in XVphy_IBufDsEnable
+ *                     Suppressed warning messages due to unused arguments
+ * 1.4   gm   29/11/16 Moved internally used APIs to xvphy_i.c/h
+ *                     Added preprocessor directives for sw footprint reduction
+ *                     Fixed c++ compiler warnings
+ * 1.6   gm   12/06/17 Changed FAILURE return value of XVphy_DrpRead to 0xDEAD
+ *                     Added XVphy_DrpRd, XVphy_SetErrorCallback,
+ *                        XVphy_SetPllLayoutErrorCallback and
+ *                        XVphy_RegisterDebug APIs
+ *                     Added filter in XVphy_MmcmStart to prevent MMCM from
+ *                        starting when divider values are invalid
+ * 1.7   gm   13/09/17 Added GTYE4 support
+ *                     Updated XVphy_MmcmStart to be able to support a system
+ *                        with active HDMI and DP
+ *                     Added xvphy_mmcme2/3/4.c drivers to move MMCM
+ *                        configuration from RTL to SW
+ *                     Moved XVphy_MmcmWriteParameters to xvphy_mmcme2/3/4.c
+ *                     Added XVphy_SetPolarity, XVphy_SetPrbsSel and
+ *                        XVphy_TxPrbsForceError APIs
+ * 1.8   gm   05/14/18 Removed XVphy_DrpWrite and XVphy_DrpRead APIs
+ *            23/07/18 Added APIs XVphy_SetTxVoltageSwing and
+ *                       XVphy_SetTxPreEmphasis from xvphy_i.c/h
+ *                     Added XVphy_SetTxPostCursor API
+ * 1.9   gm   14/05/18 Added XVphy_SetRxLpm from xvphy_i.c/.h
+ *
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include <linux/string.h>
+#include "xstatus.h"
+#include "xvphy.h"
+#include "xvphy_i.h"
+#include "xvphy_hdmi.h"
+#include <linux/delay.h>
+#include "xvphy_gt.h"
+
+/**************************** Function Prototypes *****************************/
+static u32 XVphy_DrpAccess(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u16 Addr, u16 *Val);
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function retrieves the configuration for this Video PHY instance and
+ * fills in the InstancePtr->Config structure.
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ * @param	ConfigPtr is a pointer to the configuration structure that will
+ *		be used to copy the settings from.
+ * @param	EffectiveAddr is the device base address in the virtual memory
+ *		space. If the address translation is not used, then the physical
+ *		address is passed.
+ *
+ * @return	None.
+ *
+ * @note	Unexpected errors may occur if the address mapping is changed
+ *		after this function is invoked.
+ *
+*******************************************************************************/
+void XVphy_CfgInitialize(XVphy *InstancePtr, XVphy_Config *ConfigPtr,
+		UINTPTR EffectiveAddr)
+{
+	u8 Sel;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(ConfigPtr != NULL);
+	Xil_AssertVoid(EffectiveAddr != 0x0);
+
+	(void)memset((void *)InstancePtr, 0, sizeof(XVphy));
+	InstancePtr->IsReady = 0;
+
+	InstancePtr->Config = *ConfigPtr;
+	InstancePtr->Config.BaseAddr = EffectiveAddr;
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	InstancePtr->GtAdaptor = &Gtxe2Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+	InstancePtr->GtAdaptor = &Gthe2Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+	InstancePtr->GtAdaptor = &Gtpe2Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+	InstancePtr->GtAdaptor = &Gthe3Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+	InstancePtr->GtAdaptor = &Gthe4Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+	InstancePtr->GtAdaptor = &Gtye4Config;
+#endif
+
+	const XVphy_SysClkDataSelType SysClkCfg[7][2] = {
+		{(XVphy_SysClkDataSelType)0, XVPHY_SYSCLKSELDATA_TYPE_CPLL_OUTCLK},
+		{(XVphy_SysClkDataSelType)1, XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK},
+		{(XVphy_SysClkDataSelType)2, XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK},
+		{(XVphy_SysClkDataSelType)3, XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK},
+		{(XVphy_SysClkDataSelType)4, XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK},
+		{(XVphy_SysClkDataSelType)5, XVPHY_SYSCLKSELDATA_TYPE_PLL1_OUTCLK},
+		{(XVphy_SysClkDataSelType)6, XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK},
+	};
+	for (Sel = 0; Sel < 7; Sel++) {
+		if (InstancePtr->Config.TxSysPllClkSel == SysClkCfg[Sel][0]) {
+			InstancePtr->Config.TxSysPllClkSel = SysClkCfg[Sel][1];
+		}
+		if (InstancePtr->Config.RxSysPllClkSel == SysClkCfg[Sel][0]) {
+			InstancePtr->Config.RxSysPllClkSel = SysClkCfg[Sel][1];
+		}
+	}
+
+	InstancePtr->Config.TxRefClkSel = (XVphy_PllRefClkSelType)
+			(InstancePtr->Config.TxRefClkSel +
+					XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+	InstancePtr->Config.RxRefClkSel = (XVphy_PllRefClkSelType)
+			(InstancePtr->Config.RxRefClkSel +
+					XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+	InstancePtr->Config.DruRefClkSel = (XVphy_PllRefClkSelType)
+			(InstancePtr->Config.DruRefClkSel +
+					XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0);
+
+	/* Correct RefClkSel offsets for GTPE2 EAST and WEST RefClks */
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+		if (InstancePtr->Config.TxRefClkSel > 6) {
+			InstancePtr->Config.TxRefClkSel = (XVphy_PllRefClkSelType)
+					(InstancePtr->Config.TxRefClkSel - 4);
+		}
+		if (InstancePtr->Config.RxRefClkSel > 6) {
+			InstancePtr->Config.RxRefClkSel = (XVphy_PllRefClkSelType)
+					(InstancePtr->Config.RxRefClkSel - 4);
+		}
+		if (InstancePtr->Config.DruRefClkSel > 6) {
+			InstancePtr->Config.DruRefClkSel = (XVphy_PllRefClkSelType)
+					(InstancePtr->Config.DruRefClkSel - 4);
+		}
+	}
+
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+}
+
+/*****************************************************************************/
+/**
+* This function will initialize the PLL selection for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	QpllRefClkSel is the QPLL reference clock selection for the
+*		quad.
+*		- In GTP, this is used to hold PLL0 refclk selection.
+* @param	CpllRefClkSel is the CPLL reference clock selection for the
+*		quad.
+*		- In GTP, this is used to hold PLL1 refclk selection.
+* @param	TxPllSelect is the reference clock selection for the quad's
+*		TX PLL dividers.
+* @param	RxPllSelect is the reference clock selection for the quad's
+*		RX PLL dividers.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_PllInitialize(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_PllRefClkSelType QpllRefClkSel,
+		XVphy_PllRefClkSelType CpllRefClkSel,
+		XVphy_PllType TxPllSelect, XVphy_PllType RxPllSelect)
+{
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	/* Set configuration in software. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_CfgPllRefClkSel(InstancePtr, QuadId,
+				XVPHY_CHANNEL_ID_CMNA, QpllRefClkSel);
+		XVphy_CfgPllRefClkSel(InstancePtr, QuadId,
+				XVPHY_CHANNEL_ID_CHA, CpllRefClkSel);
+	}
+	/* GTP. */
+	else {
+		XVphy_CfgPllRefClkSel(InstancePtr, QuadId,
+				XVPHY_CHANNEL_ID_CMN0,	QpllRefClkSel);
+		XVphy_CfgPllRefClkSel(InstancePtr, QuadId,
+				XVPHY_CHANNEL_ID_CMN1, CpllRefClkSel);
+	}
+	XVphy_CfgSysClkDataSel(InstancePtr, QuadId, XVPHY_DIR_TX,
+			Pll2SysClkData(TxPllSelect));
+	XVphy_CfgSysClkDataSel(InstancePtr, QuadId, XVPHY_DIR_RX,
+			Pll2SysClkData(RxPllSelect));
+	XVphy_CfgSysClkOutSel(InstancePtr, QuadId, XVPHY_DIR_TX,
+			Pll2SysClkOut(TxPllSelect));
+	XVphy_CfgSysClkOutSel(InstancePtr, QuadId, XVPHY_DIR_RX,
+			Pll2SysClkOut(RxPllSelect));
+
+	/* Write configuration to hardware at once. */
+	XVphy_WriteCfgRefClkSelReg(InstancePtr, QuadId);
+
+	return XST_SUCCESS;
+}
+
+/******************************************************************************/
+/*
+* This function installs a custom delay/sleep function to be used by the XVphy
+* driver.
+*
+* @param	InstancePtr is a pointer to the XVphy instance.
+* @param	CallbackFunc is the address to the callback function.
+* @param	CallbackRef is the user data item (microseconds to delay) that
+*		will be passed to the custom sleep/delay function when it is
+*		invoked.
+*
+* @return	None.
+*
+* @note		None.
+*
+*******************************************************************************/
+void XVphy_SetUserTimerHandler(XVphy *InstancePtr,
+		XVphy_TimerHandler CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	InstancePtr->UserTimerWaitUs = CallbackFunc;
+	InstancePtr->UserTimerPtr = CallbackRef;
+}
+
+/******************************************************************************/
+/**
+* This function is the delay/sleep function for the XVphy driver. For the Zynq
+* family, there exists native sleep functionality. For MicroBlaze however,
+* there does not exist such functionality. In the MicroBlaze case, the default
+* method for delaying is to use a predetermined amount of loop iterations. This
+* method is prone to inaccuracy and dependent on system configuration; for
+* greater accuracy, the user may supply their own delay/sleep handler, pointed
+* to by InstancePtr->UserTimerWaitUs, which may have better accuracy if a
+* hardware timer is used.
+*
+* @param	InstancePtr is a pointer to the XVphy instance.
+* @param	MicroSeconds is the number of microseconds to delay/sleep for.
+*
+* @return	None.
+*
+* @note		None.
+*
+*******************************************************************************/
+void XVphy_WaitUs(XVphy *InstancePtr, u32 MicroSeconds)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	if (MicroSeconds == 0) {
+		return;
+	}
+
+	if (InstancePtr->UserTimerWaitUs != NULL) {
+		/* Use the timer handler specified by the user for better
+		 * accuracy. */
+		InstancePtr->UserTimerWaitUs(InstancePtr, MicroSeconds);
+	}
+	else {
+	    /* Wait the requested amount of time. */
+	    usleep_range(MicroSeconds, MicroSeconds + MicroSeconds/10);
+	}
+}
+
+#if defined (XPAR_XDP_0_DEVICE_ID)
+/*****************************************************************************/
+/**
+* This function will initialize the clocking for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ClkInitialize(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir)
+{
+	u32 Status;
+
+	Status = XVphy_ClkCalcParams(InstancePtr, QuadId, ChId, Dir, 0);
+	if (Status != XST_SUCCESS) {
+		return Status;
+	}
+
+	Status = XVphy_ClkReconfig(InstancePtr, QuadId, ChId);
+	if (Status != XST_SUCCESS) {
+		return Status;
+	}
+
+	Status = XVphy_OutDivReconfig(InstancePtr, QuadId, ChId, Dir);
+	if (Status != XST_SUCCESS) {
+		return Status;
+	}
+
+	Status = XVphy_DirReconfig(InstancePtr, QuadId, ChId, Dir);
+
+	return Status;
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will obtian the IP version.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	The IP version of the Video PHY core.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_GetVersion(XVphy *InstancePtr)
+{
+	return XVphy_ReadReg(InstancePtr->Config.BaseAddr, XVPHY_VERSION_REG);
+}
+
+/*****************************************************************************/
+/**
+* Configure the channel's line rate. This is a software only configuration and
+* this value is used in the PLL calculator.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	LineRate is the line rate to configure software.
+*
+* @return
+*		- XST_SUCCESS if the reference clock type is valid.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_CfgLineRate(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u64 LineRateHz)
+{
+	u8 Id;
+	u8 Id0;
+	u8 Id1;
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].LineRateHz =
+								LineRateHz;
+	}
+
+	return XST_SUCCESS;
+}
+
+#if defined (XPAR_XDP_0_DEVICE_ID)
+/*****************************************************************************/
+/**
+* Configure the quad's reference clock frequency. This is a software only
+* configuration and this value is used in the PLL calculator.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	RefClkType is the reference clock type to operate on.
+* @param	FreqHz is the reference clock frequency to configure software.
+*
+* @return
+*		- XST_SUCCESS if the reference clock type is valid.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_CfgQuadRefClkFreq(XVphy *InstancePtr, u8 QuadId,
+		XVphy_PllRefClkSelType RefClkType, u32 FreqHz)
+{
+	u8 RefClkIndex = RefClkType - XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0;
+
+	if (RefClkType > XVPHY_PLL_REFCLKSEL_TYPE_GTGREFCLK) {
+		return XST_FAILURE;
+	}
+	InstancePtr->Quads[QuadId].RefClkHz[RefClkIndex] = FreqHz;
+
+	return XST_SUCCESS;
+}
+#endif
+
+/*****************************************************************************/
+/**
+* Obtain the channel's PLL reference clock selection.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return	The PLL type being used by the channel.
+*
+* @note		None.
+*
+******************************************************************************/
+XVphy_PllType XVphy_GetPllType(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_ChannelId ChId)
+{
+	XVphy_SysClkDataSelType SysClkDataSel;
+	XVphy_SysClkOutSelType SysClkOutSel;
+	XVphy_PllType PllType;
+
+	SysClkDataSel = XVphy_GetSysClkDataSel(InstancePtr, QuadId, Dir, ChId);
+	SysClkOutSel = XVphy_GetSysClkOutSel(InstancePtr, QuadId, Dir, ChId);
+
+	/* The sysclk data and output reference clocks should match. */
+
+	if ((SysClkDataSel == XVPHY_SYSCLKSELDATA_TYPE_CPLL_OUTCLK) &&
+	(SysClkOutSel == XVPHY_SYSCLKSELOUT_TYPE_CPLL_REFCLK)) {
+		PllType = XVPHY_PLL_TYPE_CPLL;
+	}
+	else if ((SysClkDataSel == XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK) &&
+	(SysClkOutSel == XVPHY_SYSCLKSELOUT_TYPE_QPLL_REFCLK)) {
+		PllType = XVPHY_PLL_TYPE_QPLL;
+	}
+	else if ((SysClkDataSel == XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK) &&
+	(SysClkOutSel == XVPHY_SYSCLKSELOUT_TYPE_QPLL0_REFCLK)) {
+		PllType = XVPHY_PLL_TYPE_QPLL0;
+	}
+	else if ((SysClkDataSel == XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK) &&
+	(SysClkOutSel == XVPHY_SYSCLKSELOUT_TYPE_QPLL1_REFCLK)) {
+		PllType = XVPHY_PLL_TYPE_QPLL1;
+	}
+	else {
+		PllType = XVPHY_PLL_TYPE_UNKNOWN;
+	}
+	/* For GTHE2, GTHE3, GTHE4, GTYE4, and GTXE2. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		return PllType;
+	}
+
+	if ((SysClkDataSel == XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK) &&
+	(SysClkOutSel == XVPHY_SYSCLKSELOUT_TYPE_PLL0_REFCLK)) {
+		PllType = XVPHY_PLL_TYPE_PLL0;
+	}
+	else if ((SysClkDataSel == XVPHY_SYSCLKSELDATA_TYPE_PLL1_OUTCLK) &&
+	(SysClkOutSel == XVPHY_SYSCLKSELOUT_TYPE_PLL1_REFCLK)) {
+		PllType = XVPHY_PLL_TYPE_PLL1;
+	}
+	else {
+		PllType = XVPHY_PLL_TYPE_UNKNOWN;
+	}
+	/* For GTPE2. */
+	return PllType;
+}
+
+/*****************************************************************************/
+/**
+* This function will return the line rate in Hz for a given channel / quad.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to check.
+* @param	ChId is the channel ID for which to retrieve the line rate.
+*
+* @return	The line rate in Hz.
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XVphy_GetLineRateHz(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid((XVPHY_CHANNEL_ID_CH1 <= ChId) &&
+			(ChId <= XVPHY_CHANNEL_ID_CMN1));
+
+	return InstancePtr->Quads[QuadId].Plls[ChId -
+		XVPHY_CHANNEL_ID_CH1].LineRateHz;
+}
+
+#if defined (XPAR_XDP_0_DEVICE_ID)
+/*****************************************************************************/
+/**
+* This function will wait for a PMA reset done on the specified channel(s) or
+* time out.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return
+*		- XST_SUCCESS if the PMA reset has finalized.
+*		- XST_FAILURE otherwise; waiting for the reset done timed out.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_WaitForPmaResetDone(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+	u8 Retry = 0;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_INIT_STATUS_REG;
+	}
+	else {
+		RegOffset = XVPHY_RX_INIT_STATUS_REG;
+	}
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		MaskVal = XVPHY_TXRX_INIT_STATUS_PMARESETDONE_ALL_MASK;
+	}
+	else {
+		MaskVal = XVPHY_TXRX_INIT_STATUS_PMARESETDONE_MASK(ChId);
+	}
+	do {
+		RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+		if (!(RegVal & MaskVal)){
+			XVphy_WaitUs(InstancePtr, 1000);
+			Retry++;
+		}
+	} while ((!(RegVal & MaskVal)) && (Retry < 15));
+
+	if (Retry == 15){
+		return XST_FAILURE;
+	}
+	else {
+		return XST_SUCCESS;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will wait for a reset done on the specified channel(s) or time
+* out.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return
+*		- XST_SUCCESS if the reset has finalized.
+*		- XST_FAILURE otherwise; waiting for the reset done timed out.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_WaitForResetDone(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+	u8 Retry = 0;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_INIT_STATUS_REG;
+	}
+	else {
+		RegOffset = XVPHY_RX_INIT_STATUS_REG;
+	}
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		MaskVal = XVPHY_TXRX_INIT_STATUS_RESETDONE_ALL_MASK;
+	}
+	else {
+		MaskVal = XVPHY_TXRX_INIT_STATUS_RESETDONE_MASK(ChId);
+	}
+	do {
+		RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+		if (!(RegVal & MaskVal)){
+			XVphy_WaitUs(InstancePtr, 1000);
+			Retry++;
+		}
+	} while ((!(RegVal & MaskVal)) && (Retry < 15));
+
+	if (Retry == 15){
+		return XST_FAILURE;
+	}
+	else {
+		return XST_SUCCESS;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will wait for a PLL lock on the specified channel(s) or time
+* out.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return
+*		- XST_SUCCESS if the PLL(s) have locked.
+*		- XST_FAILURE otherwise; waiting for the lock timed out.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_WaitForPllLock(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	u32 Status = XST_FAILURE;
+	u8 Retry = 0;
+
+	do {
+		XVphy_WaitUs(InstancePtr, 1000);
+		Status = XVphy_IsPllLocked(InstancePtr, QuadId, ChId);
+		Retry++;
+	} while ((Status != XST_SUCCESS) && (Retry < 15));
+
+	return Status;
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will reset the GT's PLL logic.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ResetGtPll(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Hold)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_INIT_REG;
+	}
+	else {
+		RegOffset = XVPHY_RX_INIT_REG;
+	}
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		MaskVal = XVPHY_TXRX_INIT_PLLGTRESET_ALL_MASK;
+	}
+	else {
+		MaskVal = XVPHY_TXRX_INIT_PLLGTRESET_MASK(ChId);
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	/* Assert reset. */
+	RegVal |= MaskVal;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~MaskVal;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will reset the GT's TX/RX logic.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ResetGtTxRx(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Hold)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_INIT_REG;
+	}
+	else {
+		RegOffset = XVPHY_RX_INIT_REG;
+	}
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		MaskVal =  XVPHY_TXRX_INIT_GTRESET_ALL_MASK;
+	}
+	else {
+		MaskVal = XVPHY_TXRX_INIT_GTRESET_MASK(ChId);
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	/* Assert reset. */
+	RegVal |= MaskVal;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~MaskVal;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set/clear the TX/RX polarity bit.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Polarity 0-Not inverted 1-Inverted
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_SetPolarity(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Polarity)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_CONTROL_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal =  XVPHY_TX_CONTROL_TXPOLARITY_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_TX_CONTROL_TXPOLARITY_MASK(ChId);
+		}
+	}
+	else {
+		RegOffset = XVPHY_RX_CONTROL_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal = XVPHY_RX_CONTROL_RXPOLARITY_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_RX_CONTROL_RXPOLARITY_MASK(ChId);
+		}
+	}
+
+	/* Read TX|RX Control Register */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Clear Polarity Register bits */
+	RegVal &= ~MaskVal;
+
+	if (Polarity) {
+		RegVal |= MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX/RXPRBSEL of the GT
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Pattern is the pattern XVphy_PrbsPattern
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_SetPrbsSel(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, XVphy_PrbsPattern Pattern)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+	u32 PrbsEnc = 0x0;
+	u8 Id, Id0, Id1;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_CONTROL_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal =  XVPHY_TX_CONTROL_TXPRBSSEL_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_TX_CONTROL_TXPRBSSEL_MASK(ChId);
+		}
+		PrbsEnc = (u32) (((Pattern & 0x8) << 1) | (Pattern & 0x7));
+	}
+	else {
+		RegOffset = XVPHY_RX_CONTROL_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal = XVPHY_RX_CONTROL_RXPRBSSEL_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_RX_CONTROL_RXPRBSSEL_MASK(ChId);
+		}
+		PrbsEnc = (u32) (Pattern & 0xF);
+	}
+
+	/* Read TX|RX Control Register */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Mask out PRBS Register bits */
+	RegVal &= ~MaskVal;
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		RegVal |= PrbsEnc << ((Dir == XVPHY_DIR_TX) ?
+					XVPHY_TX_CONTROL_TXPRBSSEL_SHIFT(Id) :
+					XVPHY_RX_CONTROL_RXPRBSSEL_SHIFT(Id));
+	}
+
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX/RXPRBSEL of the GT
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ForceErr 0-No Error 1-Force Error
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_TxPrbsForceError(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, u8 ForceErr)
+{
+	u32 RegVal;
+	u32 MaskVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		MaskVal =  XVPHY_TX_CONTROL_TXPRBSFORCEERR_ALL_MASK;
+	}
+	else {
+		MaskVal = XVPHY_TX_CONTROL_TXPRBSFORCEERR_MASK(ChId);
+	}
+
+	/* Read TX|RX Control Register */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+					XVPHY_TX_CONTROL_REG);
+
+	/* Clear Polarity Register bits */
+	RegVal &= ~MaskVal;
+
+	if (ForceErr) {
+		RegVal |= MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+					XVPHY_TX_CONTROL_REG, RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX voltage swing value for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Vs is the voltage swing value to write.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_SetTxVoltageSwing(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, u8 Vs)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if ((ChId == XVPHY_CHANNEL_ID_CH1) || (ChId == XVPHY_CHANNEL_ID_CH2)) {
+		RegOffset = XVPHY_TX_DRIVER_CH12_REG;
+	}
+	else {
+		RegOffset = XVPHY_TX_DRIVER_CH34_REG;
+	}
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	MaskVal = XVPHY_TX_DRIVER_TXDIFFCTRL_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= (Vs << XVPHY_TX_DRIVER_TXDIFFCTRL_SHIFT(ChId));
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX pre-emphasis value for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Pe is the pre-emphasis value to write.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_SetTxPreEmphasis(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId, u8 Pe)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if ((ChId == XVPHY_CHANNEL_ID_CH1) || (ChId == XVPHY_CHANNEL_ID_CH2)) {
+		RegOffset = XVPHY_TX_DRIVER_CH12_REG;
+	}
+	else {
+		RegOffset = XVPHY_TX_DRIVER_CH34_REG;
+	}
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	MaskVal = XVPHY_TX_DRIVER_TXPRECURSOR_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= (Pe << XVPHY_TX_DRIVER_TXPRECURSOR_SHIFT(ChId));
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will set the TX post-curosr value for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Pe is the pre-emphasis value to write.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_SetTxPostCursor(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u8 Pc)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if ((ChId == XVPHY_CHANNEL_ID_CH1) || (ChId == XVPHY_CHANNEL_ID_CH2)) {
+		RegOffset = XVPHY_TX_DRIVER_CH12_REG;
+	}
+	else {
+		RegOffset = XVPHY_TX_DRIVER_CH34_REG;
+	}
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	MaskVal = XVPHY_TX_DRIVER_TXPOSTCURSOR_MASK(ChId);
+	RegVal &= ~MaskVal;
+	RegVal |= (Pc << XVPHY_TX_DRIVER_TXPOSTCURSOR_SHIFT(ChId));
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will enable or disable the LPM logic in the Video PHY core.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable will enable (if 1) or disable (if 0) the LPM logic.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_SetRxLpm(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Enable)
+{
+	u32 RegVal;
+	u32 MaskVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	Dir = Dir;
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+							XVPHY_RX_EQ_CDR_REG);
+
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		MaskVal = XVPHY_RX_CONTROL_RXLPMEN_ALL_MASK;
+	}
+	else {
+		MaskVal = XVPHY_RX_CONTROL_RXLPMEN_MASK(ChId);
+	}
+
+	if (Enable) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_RX_EQ_CDR_REG,
+									RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will initiate a write DRP transaction. It is a wrapper around
+* XVphy_DrpAccess.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID on which to direct the DRP access.
+* @param	Addr is the DRP address to issue the DRP access to.
+* @param	Val is the value to write to the DRP address.
+*
+* @return
+*		- XST_SUCCESS if the DRP access was successful.
+*		- XST_FAILURE otherwise, if the busy bit did not go low, or if
+*		  the ready bit did not go high.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_DrpWr(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u16 Addr, u16 Val)
+{
+	return XVphy_DrpAccess(InstancePtr, QuadId, ChId,
+			XVPHY_DIR_TX, /* Write. */
+			Addr, &Val);
+}
+
+/*****************************************************************************/
+/**
+* This function will initiate a read DRP transaction. It is a wrapper around
+* XVphy_DrpAccess.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID on which to direct the DRP access.
+* @param	Addr is the DRP address to issue the DRP access to.
+* @param	RetVal is the DRP read_value returned implicitly.
+*
+* @return
+*		- XST_SUCCESS if the DRP access was successful.
+*		- XST_FAILURE otherwise, if the busy bit did not go low, or if
+*		  the ready bit did not go high.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_DrpRd(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+        u16 Addr, u16 *RetVal)
+{
+	u32 Status;
+	u16 Val;
+
+	Status = XVphy_DrpAccess(InstancePtr, QuadId, ChId,
+			XVPHY_DIR_RX, /* Read. */
+			Addr, &Val);
+
+    *RetVal = Val;
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will power down the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the power down if set
+*		to 1. If set to 0: power down, then power back up.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_MmcmPowerDown(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir,
+		u8 Hold)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffsetCtrl = XVPHY_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XVPHY_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	/* Power down. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+	RegVal |= XVPHY_MMCM_USRCLK_CTRL_PWRDWN_MASK;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	if (!Hold) {
+		/* Power up. */
+		RegVal &= ~XVPHY_MMCM_USRCLK_CTRL_PWRDWN_MASK;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl,
+									RegVal);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will start the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_MmcmStart(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir)
+{
+#if defined (XPAR_XDP_0_DEVICE_ID)
+#if defined (XPAR_XV_HDMITX_0_DEVICE_ID) || defined (XPAR_XV_HDMIRX_0_DEVICE_ID)
+	if (InstancePtr->Config.TxProtocol == XVPHY_PROTOCOL_DP ||
+		InstancePtr->Config.RxProtocol == XVPHY_PROTOCOL_DP) {
+#endif
+	/* Enable MMCM. */
+	XVphy_MmcmPowerDown(InstancePtr, QuadId, Dir, FALSE);
+
+	XVphy_WaitUs(InstancePtr, 10000);
+
+	/* Toggle MMCM reset. */
+	XVphy_MmcmReset(InstancePtr, QuadId, Dir, TRUE);
+
+	/* Configure MMCM. */
+	XVphy_MmcmWriteParameters(InstancePtr, QuadId, Dir);
+
+	/* Toggle MMCM reset. */
+	XVphy_MmcmReset(InstancePtr, QuadId, Dir, FALSE);
+#endif
+#if defined (XPAR_XV_HDMITX_0_DEVICE_ID) || defined (XPAR_XV_HDMIRX_0_DEVICE_ID)
+#if defined (XPAR_XDP_0_DEVICE_ID)
+	} else if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX) ||
+			   XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+#endif
+	XVphy_Mmcm *MmcmPtr;
+
+	if (Dir == XVPHY_DIR_RX) {
+		MmcmPtr= &InstancePtr->Quads[QuadId].RxMmcm;
+	}
+	else {
+		MmcmPtr= &InstancePtr->Quads[QuadId].TxMmcm;
+	}
+
+	/* Check values if valid */
+	if (!((MmcmPtr->ClkOut0Div > 0) && (MmcmPtr->ClkOut0Div <= 128) &&
+		  (MmcmPtr->ClkOut1Div > 0) && (MmcmPtr->ClkOut1Div <= 128) &&
+		  (MmcmPtr->ClkOut2Div > 0) && (MmcmPtr->ClkOut2Div <= 128))) {
+		return;
+	}
+
+	/* Assert MMCM reset. */
+	XVphy_MmcmReset(InstancePtr, QuadId, Dir, TRUE);
+
+	/* Configure MMCM. */
+	XVphy_MmcmWriteParameters(InstancePtr, QuadId, Dir);
+
+	/* Release MMCM reset. */
+	XVphy_MmcmReset(InstancePtr, QuadId, Dir, FALSE);
+
+	/* Unmask the MMCM Lock */
+	XVphy_MmcmLockedMaskEnable(InstancePtr, 0, Dir, FALSE);
+#if defined (XPAR_XDP_0_DEVICE_ID)
+	}
+#endif
+#endif
+
+	XVphy_LogWrite(InstancePtr, (Dir == XVPHY_DIR_TX) ?
+		XVPHY_LOG_EVT_TXPLL_RECONFIG : XVPHY_LOG_EVT_RXPLL_RECONFIG, 1);
+}
+
+/*****************************************************************************/
+/**
+* This function enables the TX or RX IBUFDS peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the IBUFDS, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_IBufDsEnable(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir,
+		u8 Enable)
+{
+	XVphy_PllRefClkSelType *TypePtr, *DruTypePtr, DruTypeDummy;
+	u32 RegAddr = XVPHY_IBUFDS_GTXX_CTRL_REG;
+	u32 RegVal;
+	u32 MaskVal = 0;
+	DruTypeDummy = XVPHY_PLL_REFCLKSEL_TYPE_GTGREFCLK;
+	DruTypePtr = &DruTypeDummy;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		TypePtr = &InstancePtr->Config.TxRefClkSel;
+	}
+	else {
+		TypePtr = &InstancePtr->Config.RxRefClkSel;
+		if (InstancePtr->Config.DruIsPresent) {
+			DruTypePtr = &InstancePtr->Config.DruRefClkSel;
+		}
+	}
+
+	if ((*TypePtr == XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0) ||
+			((InstancePtr->Config.DruIsPresent) &&
+			(*DruTypePtr == XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0))) {
+		MaskVal = XVPHY_IBUFDS_GTXX_CTRL_GTREFCLK0_CEB_MASK;
+	}
+	else if ((*TypePtr == XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK1) ||
+			((InstancePtr->Config.DruIsPresent) &&
+			(*DruTypePtr == XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK1))) {
+		MaskVal = XVPHY_IBUFDS_GTXX_CTRL_GTREFCLK1_CEB_MASK;
+	}
+	else {
+		if (Dir == XVPHY_DIR_TX) {
+			RegAddr = XVPHY_MISC_TXUSRCLK_REG;
+		}
+		else {
+			RegAddr = XVPHY_MISC_RXUSRCLK_REG;
+		}
+		MaskVal = XVPHY_MISC_XXUSRCLK_REFCLK_CEB_MASK;
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegAddr);
+
+	if (Enable) {
+		RegVal &= ~MaskVal;
+	}
+	else {
+		RegVal |= MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegAddr, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function enables the TX or RX CLKOUT1 OBUFTDS peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the OBUFTDS, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_Clkout1OBufTdsEnable(XVphy *InstancePtr, XVphy_DirectionType Dir,
+		u8 Enable)
+{
+	u32 RegVal;
+	u32 RegOffset;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_MISC_TXUSRCLK_REG;
+	}
+	else {
+		RegOffset = XVPHY_MISC_RXUSRCLK_REG;
+	}
+
+	/* Read XXUSRCLK MISC register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Write new value to XXUSRCLK MISC register. */
+	if (Enable) {
+		RegVal |= XVPHY_MISC_XXUSRCLK_CKOUT1_OEN_MASK;
+	}
+	else {
+		RegVal &= ~XVPHY_MISC_XXUSRCLK_CKOUT1_OEN_MASK;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+#if defined (XPAR_XDP_0_DEVICE_ID)
+/*****************************************************************************/
+/**
+* This function resets the BUFG_GT peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Dir is an indicator for TX or RX
+* @param	Reset specifies TRUE/FALSE value to either assert or deassert
+*		reset on the BUFG_GT, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_BufgGtReset(XVphy *InstancePtr, XVphy_DirectionType Dir, u8 Reset)
+{
+	u32 RegVal;
+	u32 RegOffset;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_BUFGGT_TXUSRCLK_REG;
+	}
+	else {
+		RegOffset = XVPHY_BUFGGT_RXUSRCLK_REG;
+	}
+
+	/* Read BUFG_GT register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+
+	/* Write new value to BUFG_GT register. */
+	if (Reset) {
+		RegVal |= XVPHY_BUFGGT_XXUSRCLK_CLR_MASK;
+	}
+	else {
+		RegVal &= ~XVPHY_BUFGGT_XXUSRCLK_CLR_MASK;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will set 8b10b encoding for the specified GT PLL.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable is an indicator to enable/disable 8b10b encoding.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_Set8b10b(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Enable)
+{
+	u32 RegOffset;
+	u32 MaskVal;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_CONTROL_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal = XVPHY_TX_CONTROL_TX8B10BEN_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_TX_CONTROL_TX8B10BEN_MASK(ChId);
+		}
+	}
+	else {
+		RegOffset = XVPHY_RX_CONTROL_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal = XVPHY_RX_CONTROL_RX8B10BEN_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_RX_CONTROL_RX8B10BEN_MASK(ChId);
+		}
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	if (Enable) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function returns true when the RX and TX are bonded and are running
+* from the same (RX) reference clock.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	TRUE if the RX and TX are using the same PLL, FALSE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_IsBonded(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	XVphy_SysClkDataSelType RxSysClkDataSel;
+	XVphy_SysClkOutSelType RxSysClkOutSel;
+	XVphy_SysClkDataSelType TxSysClkDataSel;
+	XVphy_SysClkOutSelType TxSysClkOutSel;
+
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		ChId = XVPHY_CHANNEL_ID_CH1;
+	}
+
+	RxSysClkDataSel = XVphy_GetSysClkDataSel(InstancePtr, QuadId,
+							XVPHY_DIR_RX, ChId);
+	RxSysClkOutSel = XVphy_GetSysClkOutSel(InstancePtr, QuadId,
+							XVPHY_DIR_RX, ChId);
+	TxSysClkDataSel = XVphy_GetSysClkDataSel(InstancePtr, QuadId,
+							XVPHY_DIR_TX, ChId);
+	TxSysClkOutSel = XVphy_GetSysClkOutSel(InstancePtr, QuadId,
+							XVPHY_DIR_TX, ChId);
+
+	if ((RxSysClkDataSel == TxSysClkDataSel) &&
+					(RxSysClkOutSel == TxSysClkOutSel)) {
+		return TRUE;
+	}
+
+	return FALSE;
+}
+
+/*****************************************************************************/
+/**
+* This function will initiate a DRP transaction (either read or write).
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID on which to direct the DRP access.
+* @param	Dir is an indicator for write (TX) or read (RX).
+* @param	Addr is the DRP address to issue the DRP access to.
+* @param	Val is a pointer to the data value. In write mode, this pointer
+*		will hold the value to write. In read mode, this pointer will
+*		be populated with the read value.
+*
+* @return
+*		- XST_SUCCESS if the DRP access was successful.
+*		- XST_FAILURE otherwise, if the busy bit did not go low, or if
+*		  the ready bit did not go high.
+*
+* @note		In read mode (Dir == XVPHY_DIR_RX), the data pointed to by Val
+*		will be populated with the u16 value that was read._
+*
+******************************************************************************/
+static u32 XVphy_DrpAccess(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u16 Addr, u16 *Val)
+{
+	u32 RegOffsetCtrl;
+	u32 RegOffsetSts;
+	u32 RegVal;
+	u8 Retry;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	/* Determine which DRP registers to use based on channel. */
+	if (XVPHY_ISCMN(ChId)) {
+		RegOffsetCtrl = XVPHY_DRP_CONTROL_COMMON_REG;
+		RegOffsetSts = XVPHY_DRP_STATUS_COMMON_REG;
+	}
+	else if (XVPHY_ISTXMMCM(ChId)) {
+		RegOffsetCtrl = XVPHY_DRP_CONTROL_TXMMCM_REG;
+		RegOffsetSts = XVPHY_DRP_STATUS_TXMMCM_REG;
+	}
+	else if (XVPHY_ISRXMMCM(ChId)) {
+		RegOffsetCtrl = XVPHY_DRP_CONTROL_RXMMCM_REG;
+		RegOffsetSts = XVPHY_DRP_STATUS_RXMMCM_REG;
+	}
+	else {
+		RegOffsetCtrl = XVPHY_DRP_CONTROL_CH1_REG +
+			(4 * XVPHY_CH2IDX(ChId));
+		RegOffsetSts = XVPHY_DRP_STATUS_CH1_REG +
+			(4 * (XVPHY_CH2IDX(ChId)));
+	}
+
+    if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) &&
+		((InstancePtr->Config.TxProtocol == XVPHY_PROTOCOL_DP) ||
+		 (InstancePtr->Config.RxProtocol == XVPHY_PROTOCOL_DP))) {
+               ChId = XVPHY_CHANNEL_ID_CHA;
+		XVphy_WaitUs(InstancePtr, 3000);
+	}
+
+	/* Wait until the DRP status indicates that it is not busy.*/
+	Retry = 0;
+	do {
+		RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+								RegOffsetSts);
+		if (Retry > 150) {
+			return XST_FAILURE;
+		}
+		Retry++;
+	} while (RegVal & XVPHY_DRP_STATUS_DRPBUSY_MASK);
+
+	/* Write the command to the channel's DRP. */
+	RegVal = (Addr & XVPHY_DRP_CONTROL_DRPADDR_MASK);
+	RegVal |= XVPHY_DRP_CONTROL_DRPEN_MASK;
+	if (Dir == XVPHY_DIR_TX) {
+		/* Enable write. */
+		RegVal |= XVPHY_DRP_CONTROL_DRPWE_MASK;
+		RegVal |= ((*Val << XVPHY_DRP_CONTROL_DRPDI_SHIFT) &
+						XVPHY_DRP_CONTROL_DRPDI_MASK);
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	/* Wait until the DRP status indicates ready.*/
+	Retry = 0;
+	do {
+		RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+								RegOffsetSts);
+		if (Retry > 150) {
+			return XST_FAILURE;
+		}
+		Retry++;
+	} while (!(RegVal & XVPHY_DRP_STATUS_DRPRDY_MASK));
+
+	if (Dir == XVPHY_DIR_RX) {
+		/* Mask non-data out for read. */
+		RegVal &= XVPHY_DRP_STATUS_DRPO_MASK;
+		/* Populate Val with read contents. */
+		*Val = RegVal;
+	}
+	return XST_SUCCESS;
+}
+
+/******************************************************************************/
+/**
+* This function installs a callback function for the VPHY error conditions
+*
+* @param	InstancePtr is a pointer to the XVPhy instance.
+* @param	CallbackFunc is the address to the callback function.
+* @param	CallbackRef is the user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return	None.
+*
+* @note		The XVphy_ErrorHandler API calls the registered function in
+* 			  ErrorCallback and passes two arguments: 1) CallbackRef
+* 			  2) Error Type as defined by XVphy_ErrType.
+*
+* 			Sample Function Call:
+* 				CallbackFunc(CallbackRef, XVphy_ErrType);
+*
+*******************************************************************************/
+void XVphy_SetErrorCallback(XVphy *InstancePtr,
+		void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	InstancePtr->ErrorCallback = (XVphy_ErrorCallback)CallbackFunc;
+	InstancePtr->ErrorRef = CallbackRef;
+}
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+/******************************************************************************/
+/**
+* This function installs a callback function for the VPHY PLL Layout error
+* conditions
+*
+* @param	InstancePtr is a pointer to the XVPhy instance.
+* @param	CallbackFunc is the address to the callback function.
+* @param	CallbackRef is the user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return	None.
+*
+* @note		The XVphy_ErrorHandler API calls the registered function in
+* 			  ErrorCallback and passes two arguments: 1) CallbackRef
+* 			  2) Error Type as defined by XVphy_ErrType.
+*
+* 			Sample Function Call:
+* 				CallbackFunc(CallbackRef, XVphy_ErrType);
+*
+*******************************************************************************/
+void XVphy_SetPllLayoutErrorCallback(XVphy *InstancePtr,
+		void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	InstancePtr->PllLayoutErrorCallback = (XVphy_ErrorCallback)CallbackFunc;
+	InstancePtr->PllLayoutErrorRef = CallbackRef;
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function prints out Video PHY register and GT Channel and Common
+* DRP register contents.
+*
+* @param	InstancePtr is a pointer to the Vphy core instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_RegisterDebug(XVphy *InstancePtr)
+{
+	u32 RegOffset;
+	u16 DrpAddr, MaxDrpAddr;
+	u16 DrpVal, ChId;
+	u8  MaxChannels;
+
+	xil_printf("\r\nVPHY Registers\r\n");
+	xil_printf("-----------------\r\n");
+	xil_printf("Offset   |  Value\r\n");
+	xil_printf("-----------------\r\n");
+	for (RegOffset = 0; RegOffset <= 0x334; ) {
+		xil_printf("0x%04x      0x%08x\r\n",RegOffset,
+		XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset));
+		RegOffset += 4;
+	}
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	MaxDrpAddr = 0x0044;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+	MaxDrpAddr = 0x0047;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+	MaxDrpAddr = 0x002D;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+	MaxDrpAddr = 0x00B0;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+	MaxDrpAddr = 0x00B0;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+	MaxDrpAddr = 0x00B0;
+#endif
+
+	xil_printf("\r\nVPHY GT COMMON DRP Registers\r\n");
+	xil_printf("----------------------------\r\n");
+	if ((InstancePtr->HdmiIsQpllPresent == TRUE) ||
+			(InstancePtr->Config.TxProtocol == XVPHY_PROTOCOL_DP) ||
+			(InstancePtr->Config.RxProtocol == XVPHY_PROTOCOL_DP)) {
+		xil_printf("Offset   |  Value\r\n");
+		xil_printf("----------------------------\r\n");
+		for (DrpAddr = 0x0000; DrpAddr <= MaxDrpAddr; DrpAddr++) {
+			XVphy_DrpRd(InstancePtr, 0, XVPHY_CHANNEL_ID_CMN0,
+					DrpAddr, &DrpVal);
+			xil_printf("0x%04x      0x%04x\r\n",DrpAddr, DrpVal);
+		}
+	} else {
+		xil_printf("No QPLL in this VPHY Instance\r\n");
+	}
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	MaxDrpAddr = 0x015C;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+	MaxDrpAddr = 0x015E;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+	MaxDrpAddr = 0x00AD;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+	MaxDrpAddr = 0x015F;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+	MaxDrpAddr = 0x025F;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+	MaxDrpAddr = 0x028C;
+#endif
+	/* Get Max number of channels in VPHY */
+	MaxChannels = (InstancePtr->Config.RxChannels >
+					InstancePtr->Config.TxChannels) ?
+					InstancePtr->Config.RxChannels :
+					InstancePtr->Config.TxChannels;
+
+	for (ChId = 1; ChId <= MaxChannels; ChId++) {
+	xil_printf("\r\nVPHY GT CHANNEL %d DRP Registers\r\n", ChId);
+	xil_printf("-------------------------------\r\n");
+	xil_printf("Offset   |  Value\r\n");
+	xil_printf("-------------------------------\r\n");
+		for (DrpAddr = 0x0000; DrpAddr <= MaxDrpAddr; DrpAddr++) {
+			XVphy_DrpRd(InstancePtr, 0, ChId, DrpAddr, &DrpVal);
+			xil_printf("0x%04x      0x%04x\r\n",DrpAddr, DrpVal);
+		}
+	}
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy.h
@@ -0,0 +1,1011 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy.h
+ * @{
+ * @details
+ * This is main header file of the Xilinx Video PHY Controller driver
+ *
+ * <b>Video PHY Controller Overview</b>
+ *
+ * The PHY is intended to simplify the use of serial transceivers and adds
+ * domain-specific configurability. The Video PHY Controller IP is not intended
+ * to be used as a stand alone IP and must be used with Xilinx Video MACs such
+ * as HDMI 1.4/2.0 Transmitter/Receiver Subsystems and DisplayPort TX/RX
+ * Subsystems. The core enables simpler connectivity between MAC layers for TX
+ * and RX paths. However, it is still important to understand the behavior,
+ * usage, and any limitations of the transceivers. See the device specific
+ * transceiver user guide for details.
+ *
+ * <b>Video PHY Controller Driver Features</b>
+ *
+ * Video PHY Controller driver supports following features
+ *   - Xilinx DisplayPort and HDMI MAC IPs
+ *   - GTXE2, GTPE2, GTHE2, GTHE3, GTHE4 and GTYE4 GT types
+ *   - HDMI:
+ *   -   2 or 4 pixel-wide video interface
+ *   -   8/10/12/16 bits per component
+ *   -   RGB & YCbCr color space
+ *   -   Up to 4k2k 60Hz resolution at both Input and Output interface
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Added EAST, WEST, PLL0 and PLL1 definitions
+ *                     for GTPE2.
+ *                     Added more events to XVphy_LogEvent definitions
+ *                     Added TxBufferBypass in XVphy_Config structure
+ *                     Added XVphy_SetDefaultPpc and XVphy_SetPpc functions
+ *       als           Added XVphy_GetLineRateHz function.
+ * 1.2   gm            Added HdmiFastSwitch in XVphy_Config
+ *                     Changed EffectiveAddr datatype in XVphy_CfgInitialize
+ *                       to UINTPTR
+ *                     Added log events for debugging
+ * 1.2   gm   11/11/19 Added TransceiverWidth in XVphy_Config
+ * 1.4   gm   29/11/16 Moved internally used APIs to xvphy_i.c/h
+ *                     Added preprocessor directives for sw footprint reduction
+ *                     Made debug log optional (can be disabled via makefile)
+ *                     Added ERR_IRQ type_defs (not for official use for
+ *                       Xilinx debugging)
+ *                     Added transceiver width, AXIlite clk frequency and
+ *                       err_irq in XVphy_Config
+ * 1.5   gm   08/05/17 Added DrpClkFreq in XVphy_Config
+ * 1.6   gm   06/08/17 Added XVPHY_LOG_EVT_HDMI20_ERR &
+ *                       XVPHY_LOG_EVT_DRU_CLK_ERR XVphy_LogEvent enum
+ *                     Added intr events for TX and RX MMCM lock
+ *                     Marked XVphy_DrpWrite and XVphy_DrpRead as deprecated
+ *                     Added XVphy_SetErrorCallback API
+ *                     Changed ClkOutxDiv declaration to u16
+ *                     Marked XVphy_HdmiInitialize deprecated and replaced by
+ *                        XVphy_Hdmi_CfgInitialize
+ * 1.7   gm   13/09/17 Added GTYE4 support
+ *                     Added XVphy_SetPolarity, XVphy_SetPrbsSel and
+ *                        XVphy_TxPrbsForceError APIs
+ * 1.8   gm   05/14/18 Updated CDR values for DP in xvphy_gtye4.c
+ *                     Removed XVphy_DrpWrite and XVphy_DrpRead APIs
+ *            23/07/18 Added APIs XVphy_SetTxVoltageSwing and
+ *                       XVphy_SetTxPreEmphasis from xvphy_i.c/h
+ *                     Added XVphy_SetTxPostCursor API
+ * 1.9   gm   14/05/18 Added XVphy_SetRxLpm from xvphy_i.c/.h
+ *                     Removed deprecated XVphy_HdmiInitialize API
+ * </pre>
+ *
+*******************************************************************************/
+
+#ifndef XVPHY_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XVPHY_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if !defined(XV_CONFIG_LOG_VPHY_DISABLE) && !defined(XV_CONFIG_LOG_DISABLE_ALL)
+#define XV_VPHY_LOG_ENABLE
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xil_assert.h"
+#include "xvphy_hw.h"
+#include "xvidc.h"
+
+/****************************** Type Definitions ******************************/
+
+/* This typedef enumerates the different GT types available. */
+typedef enum {
+	XVPHY_GT_TYPE_GTXE2 = 1,
+	XVPHY_GT_TYPE_GTHE2 = 2,
+	XVPHY_GT_TYPE_GTPE2 = 3,
+	XVPHY_GT_TYPE_GTHE3 = 4,
+	XVPHY_GT_TYPE_GTHE4 = 5,
+	XVPHY_GT_TYPE_GTYE4 = 6,
+} XVphy_GtType;
+
+/**
+ * This typedef enumerates the various protocols handled by the Video PHY
+ * controller (VPHY).
+ */
+typedef enum {
+	XVPHY_PROTOCOL_DP = 0,
+	XVPHY_PROTOCOL_HDMI = 1,
+	XVPHY_PROTOCOL_NONE = 3
+} XVphy_ProtocolType;
+
+/* This typedef enumerates is used to specify RX/TX direction information. */
+typedef enum {
+	XVPHY_DIR_RX = 0,
+	XVPHY_DIR_TX
+} XVphy_DirectionType;
+
+/**
+ * This typedef enumerates the list of available interrupt handler types. The
+ * values are used as parameters to the XVphy_SetIntrHandler function.
+ */
+typedef enum {
+	XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE = XVPHY_INTR_TXRESETDONE_MASK,
+	XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE = XVPHY_INTR_RXRESETDONE_MASK,
+	XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK = XVPHY_INTR_CPLL_LOCK_MASK,
+	XVPHY_INTR_HANDLER_TYPE_QPLL_LOCK = XVPHY_INTR_QPLL_LOCK_MASK,
+	XVPHY_INTR_HANDLER_TYPE_QPLL0_LOCK = XVPHY_INTR_QPLL_LOCK_MASK,
+	XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE = XVPHY_INTR_TXALIGNDONE_MASK,
+	XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK = XVPHY_INTR_QPLL1_LOCK_MASK,
+	XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE =
+		XVPHY_INTR_TXCLKDETFREQCHANGE_MASK,
+	XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE =
+		XVPHY_INTR_RXCLKDETFREQCHANGE_MASK,
+	XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE =
+		XVPHY_INTR_TXMMCMUSRCLK_LOCK_MASK,
+	XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE =
+		XVPHY_INTR_RXMMCMUSRCLK_LOCK_MASK,
+	XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT = XVPHY_INTR_TXTMRTIMEOUT_MASK,
+	XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT = XVPHY_INTR_RXTMRTIMEOUT_MASK,
+} XVphy_IntrHandlerType;
+
+/**
+ * This typedef enumerates the list of available hdmi handler types. The
+ * values are used as parameters to the XVphy_SetHdmiCallback function.
+ */
+typedef enum {
+	XVPHY_HDMI_HANDLER_TXINIT = 1,	/**< TX init handler. */
+	XVPHY_HDMI_HANDLER_TXREADY,	/**< TX ready handler. */
+	XVPHY_HDMI_HANDLER_RXINIT,	/**< RX init handler. */
+	XVPHY_HDMI_HANDLER_RXREADY	/**< RX ready handler. */
+} XVphy_HdmiHandlerType;
+
+/**
+ * This typedef enumerates the different PLL types for a given GT channel.
+ */
+typedef enum {
+	XVPHY_PLL_TYPE_CPLL = 1,
+	XVPHY_PLL_TYPE_QPLL = 2,
+	XVPHY_PLL_TYPE_QPLL0 = 3,
+	XVPHY_PLL_TYPE_QPLL1 = 4,
+	XVPHY_PLL_TYPE_PLL0 = 5,
+	XVPHY_PLL_TYPE_PLL1 = 6,
+	XVPHY_PLL_TYPE_UNKNOWN = 7,
+} XVphy_PllType;
+
+/**
+ * This typedef enumerates the available channels.
+ */
+typedef enum {
+	XVPHY_CHANNEL_ID_CH1 = 1,
+	XVPHY_CHANNEL_ID_CH2 = 2,
+	XVPHY_CHANNEL_ID_CH3 = 3,
+	XVPHY_CHANNEL_ID_CH4 = 4,
+	XVPHY_CHANNEL_ID_CMN0 = 5,
+	XVPHY_CHANNEL_ID_CMN1 = 6,
+	XVPHY_CHANNEL_ID_CHA = 7,
+	XVPHY_CHANNEL_ID_CMNA = 8,
+	XVPHY_CHANNEL_ID_TXMMCM = 9,
+	XVPHY_CHANNEL_ID_RXMMCM = 10,
+	XVPHY_CHANNEL_ID_CMN = XVPHY_CHANNEL_ID_CMN0,
+} XVphy_ChannelId;
+
+/**
+ * This typedef enumerates the available reference clocks for the PLL clock
+ * selection multiplexer.
+ */
+typedef enum {
+	XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0 = XVPHY_REF_CLK_SEL_XPLL_GTREFCLK0,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK1 = XVPHY_REF_CLK_SEL_XPLL_GTREFCLK1,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTNORTHREFCLK0 =
+		XVPHY_REF_CLK_SEL_XPLL_GTNORTHREFCLK0,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTNORTHREFCLK1 =
+		XVPHY_REF_CLK_SEL_XPLL_GTNORTHREFCLK1,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTSOUTHREFCLK0 =
+		XVPHY_REF_CLK_SEL_XPLL_GTSOUTHREFCLK0,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTSOUTHREFCLK1 =
+		XVPHY_REF_CLK_SEL_XPLL_GTSOUTHREFCLK1,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTEASTREFCLK0 =
+		XVPHY_REF_CLK_SEL_XPLL_GTEASTREFCLK0,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTEASTREFCLK1 =
+		XVPHY_REF_CLK_SEL_XPLL_GTEASTREFCLK1,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTWESTREFCLK0 =
+		XVPHY_REF_CLK_SEL_XPLL_GTWESTREFCLK0,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTWESTREFCLK1 =
+		XVPHY_REF_CLK_SEL_XPLL_GTWESTREFCLK1,
+	XVPHY_PLL_REFCLKSEL_TYPE_GTGREFCLK =
+		XVPHY_REF_CLK_SEL_XPLL_GTGREFCLK,
+} XVphy_PllRefClkSelType;
+
+/**
+ * This typedef enumerates the available reference clocks used to drive the
+ * RX/TX datapaths.
+ */
+typedef enum {
+	XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL0,
+	XVPHY_SYSCLKSELDATA_TYPE_PLL1_OUTCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL1,
+	XVPHY_SYSCLKSELDATA_TYPE_CPLL_OUTCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_CPLL,
+	XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL,
+	XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL0,
+	XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL1,
+} XVphy_SysClkDataSelType;
+
+/**
+ * This typedef enumerates the available reference clocks used to drive the
+ * RX/TX output clocks.
+ */
+typedef enum {
+	XVPHY_SYSCLKSELOUT_TYPE_CPLL_REFCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CH,
+	XVPHY_SYSCLKSELOUT_TYPE_QPLL_REFCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN,
+	XVPHY_SYSCLKSELOUT_TYPE_QPLL0_REFCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN0,
+	XVPHY_SYSCLKSELOUT_TYPE_QPLL1_REFCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN1,
+	XVPHY_SYSCLKSELOUT_TYPE_PLL0_REFCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CH,
+	XVPHY_SYSCLKSELOUT_TYPE_PLL1_REFCLK =
+		XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN,
+} XVphy_SysClkOutSelType;
+
+/**
+ * This typedef enumerates the available clocks that are used as multiplexer
+ * input selections for the RX/TX output clock.
+ */
+typedef enum {
+	XVPHY_OUTCLKSEL_TYPE_OUTCLKPCS = 1,
+	XVPHY_OUTCLKSEL_TYPE_OUTCLKPMA,
+	XVPHY_OUTCLKSEL_TYPE_PLLREFCLK_DIV1,
+	XVPHY_OUTCLKSEL_TYPE_PLLREFCLK_DIV2,
+	XVPHY_OUTCLKSEL_TYPE_PROGDIVCLK
+} XVphy_OutClkSelType;
+
+/* This typedef enumerates the possible states a transceiver can be in. */
+typedef enum {
+	XVPHY_GT_STATE_IDLE,		/**< Idle state. */
+	XVPHY_GT_STATE_LOCK,		/**< Lock state. */
+	XVPHY_GT_STATE_RESET,		/**< Reset state. */
+	XVPHY_GT_STATE_ALIGN,		/**< Align state. */
+	XVPHY_GT_STATE_READY,		/**< Ready state. */
+} XVphy_GtState;
+
+#ifdef XV_VPHY_LOG_ENABLE
+typedef enum {
+	XVPHY_LOG_EVT_NONE = 1,		/**< Log event none. */
+	XVPHY_LOG_EVT_QPLL_EN,		/**< Log event QPLL enable. */
+	XVPHY_LOG_EVT_QPLL_RST,		/**< Log event QPLL reset. */
+	XVPHY_LOG_EVT_QPLL_LOCK,	/**< Log event QPLL lock. */
+	XVPHY_LOG_EVT_QPLL_RECONFIG,	/**< Log event QPLL reconfig. */
+	XVPHY_LOG_EVT_QPLL0_EN,		/**< Log event QPLL0 enable. */
+	XVPHY_LOG_EVT_QPLL0_RST,	/**< Log event QPLL0 reset. */
+	XVPHY_LOG_EVT_QPLL0_LOCK,	/**< Log event QPLL0 lock. */
+	XVPHY_LOG_EVT_QPLL0_RECONFIG,	/**< Log event QPLL0 reconfig. */
+	XVPHY_LOG_EVT_QPLL1_EN,		/**< Log event QPLL1 enable. */
+	XVPHY_LOG_EVT_QPLL1_RST,	/**< Log event QPLL1 reset. */
+	XVPHY_LOG_EVT_QPLL1_LOCK,	/**< Log event QPLL1 lock. */
+	XVPHY_LOG_EVT_QPLL1_RECONFIG,	/**< Log event QPLL1 reconfig. */
+	XVPHY_LOG_EVT_PLL0_EN,		/**< Log event PLL0 reset. */
+	XVPHY_LOG_EVT_PLL0_RST,		/**< Log event PLL0 reset. */
+	XVPHY_LOG_EVT_PLL0_LOCK,	/**< Log event PLL0 lock. */
+	XVPHY_LOG_EVT_PLL0_RECONFIG,	/**< Log event PLL0 reconfig. */
+	XVPHY_LOG_EVT_PLL1_EN,		/**< Log event PLL1 reset. */
+	XVPHY_LOG_EVT_PLL1_RST,		/**< Log event PLL1 reset. */
+	XVPHY_LOG_EVT_PLL1_LOCK,	/**< Log event PLL1 lock. */
+	XVPHY_LOG_EVT_PLL1_RECONFIG,	/**< Log event PLL1 reconfig. */
+	XVPHY_LOG_EVT_CPLL_EN,		/**< Log event CPLL reset. */
+	XVPHY_LOG_EVT_CPLL_RST,		/**< Log event CPLL reset. */
+	XVPHY_LOG_EVT_CPLL_LOCK,	/**< Log event CPLL lock. */
+	XVPHY_LOG_EVT_CPLL_RECONFIG,	/**< Log event CPLL reconfig. */
+	XVPHY_LOG_EVT_TXPLL_EN,		/**< Log event TXPLL enable. */
+	XVPHY_LOG_EVT_TXPLL_RST,	/**< Log event TXPLL reset. */
+	XVPHY_LOG_EVT_RXPLL_EN,		/**< Log event RXPLL enable. */
+	XVPHY_LOG_EVT_RXPLL_RST,	/**< Log event RXPLL reset. */
+	XVPHY_LOG_EVT_GTRX_RST,		/**< Log event GT RX reset. */
+	XVPHY_LOG_EVT_GTTX_RST,		/**< Log event GT TX reset. */
+	XVPHY_LOG_EVT_VID_TX_RST,	/**< Log event Vid TX reset. */
+	XVPHY_LOG_EVT_VID_RX_RST,	/**< Log event Vid RX reset. */
+	XVPHY_LOG_EVT_TX_ALIGN,		/**< Log event TX align. */
+	XVPHY_LOG_EVT_TX_ALIGN_TMOUT,	/**< Log event TX align Timeout. */
+	XVPHY_LOG_EVT_TX_TMR,		/**< Log event TX timer. */
+	XVPHY_LOG_EVT_RX_TMR,		/**< Log event RX timer. */
+	XVPHY_LOG_EVT_GT_RECONFIG,	/**< Log event GT reconfig. */
+	XVPHY_LOG_EVT_GT_TX_RECONFIG,	/**< Log event GT reconfig. */
+	XVPHY_LOG_EVT_GT_RX_RECONFIG,	/**< Log event GT reconfig. */
+	XVPHY_LOG_EVT_INIT,		/**< Log event init. */
+	XVPHY_LOG_EVT_TXPLL_RECONFIG,	/**< Log event TXPLL reconfig. */
+	XVPHY_LOG_EVT_RXPLL_RECONFIG,	/**< Log event RXPLL reconfig. */
+	XVPHY_LOG_EVT_RXPLL_LOCK,	/**< Log event RXPLL lock. */
+	XVPHY_LOG_EVT_TXPLL_LOCK,	/**< Log event TXPLL lock. */
+	XVPHY_LOG_EVT_TX_RST_DONE,	/**< Log event TX reset done. */
+	XVPHY_LOG_EVT_RX_RST_DONE,	/**< Log event RX reset done. */
+	XVPHY_LOG_EVT_TX_FREQ,		/**< Log event TX frequency. */
+	XVPHY_LOG_EVT_RX_FREQ,		/**< Log event RX frequency. */
+	XVPHY_LOG_EVT_DRU_EN,		/**< Log event DRU enable/disable. */
+	XVPHY_LOG_EVT_GT_PLL_LAYOUT,/**< Log event GT PLL Layout Change. */
+	XVPHY_LOG_EVT_GT_UNBONDED,  /**< Log event GT Unbonded Change. */
+	XVPHY_LOG_EVT_1PPC_ERR,     /**< Log event 1 PPC Error. */
+	XVPHY_LOG_EVT_PPC_MSMTCH_ERR,/**< Log event PPC MismatchError. */
+	XVPHY_LOG_EVT_VDCLK_HIGH_ERR,/**< Log event VidClk more than 148.5 MHz. */
+	XVPHY_LOG_EVT_NO_DRU,		/**< Log event Vid not supported no DRU. */
+	XVPHY_LOG_EVT_GT_QPLL_CFG_ERR,/**< Log event QPLL Config not found. */
+	XVPHY_LOG_EVT_GT_CPLL_CFG_ERR,/**< Log event QPLL Config not found. */
+	XVPHY_LOG_EVT_VD_NOT_SPRTD_ERR,/**< Log event Vid format not supported. */
+	XVPHY_LOG_EVT_MMCM_ERR,		/**< Log event MMCM Config not found. */
+	XVPHY_LOG_EVT_HDMI20_ERR,	/**< Log event HDMI2.0 not supported. */
+	XVPHY_LOG_EVT_NO_QPLL_ERR,	/**< Log event QPLL not present. */
+	XVPHY_LOG_EVT_DRU_CLK_ERR,	/**< Log event DRU clk wrong freq. */
+	XVPHY_LOG_EVT_USRCLK_ERR,	/**< Log event usrclk more than 297 MHz. */
+	XVPHY_LOG_EVT_DUMMY,		/**< Dummy Event should be last */
+} XVphy_LogEvent;
+#endif
+
+/* This typedef enumerates the different MMCM Dividers */
+typedef enum {
+  MMCM_CLKFBOUT_MULT_F, /* M */
+  MMCM_DIVCLK_DIVIDE,   /* D */
+  MMCM_CLKOUT_DIVIDE    /* On */
+} XVphy_MmcmDivType;
+
+/* This typedef enumerates the possible error conditions. */
+typedef enum {
+	XVPHY_ERR_QPLL_CFG    = 0x1,	/**< QPLL CFG not found. */
+	XVPHY_ERR_CPLL_CFG    = 0x2,	/**< CPLL CFG not found. */
+	XVPHY_ERR_NO_DRU      = 0x4,	/**< No DRU in design. */
+	XVPHY_ERR_VD_NOT_SPRTD= 0x8,	/**< Video Not Supported. */
+	XVPHY_ERR_MMCM_CFG    = 0x10,	/**< MMCM CFG not found. */
+	XVPHY_ERR_PLL_LAYOUT  = 0x20,	/**< PLL Error. */
+	XVPHY_ERR_BONDED_DRU  = 0x40,	/**< DRU and Bonded Mode Error. */
+	XVPHY_ERR_NO_QPLL     = 0x80,	/**< No QPLL Error. */
+	XVPHY_ERR_DRU_CLK     = 0x100,	/**< Wrong DRU clk freq Error. */
+	XVPHY_ERR_USRCLK      = 0x200,	/**< USRCLK Error. */
+} XVphy_ErrType;
+
+/* This typedef enumerates the Linerate to TMDS Clock ratio
+ * for HDMI TX TMDS Clock pattern generator. */
+typedef enum {
+	XVPHY_Patgen_Ratio_10    = 0x1,	/**< LR:Clock Ratio = 10 */
+	XVPHY_Patgen_Ratio_20    = 0x2,	/**< LR:Clock Ratio = 20 */
+	XVPHY_Patgen_Ratio_30    = 0x3,	/**< LR:Clock Ratio = 30 */
+	XVPHY_Patgen_Ratio_40    = 0x4,	/**< LR:Clock Ratio = 40 */
+	XVPHY_Patgen_Ratio_50    = 0x5,	/**< LR:Clock Ratio = 50 */
+} XVphy_HdmiTx_Patgen;
+
+/**
+ * This typedef enumerates the available PRBS patterns available
+ * from the
+ */
+typedef enum {
+#if (XPAR_VPHY_0_TRANSCEIVER == 2) || \
+	(XPAR_VPHY_0_TRANSCEIVER == 4) || \
+	(XPAR_VPHY_0_TRANSCEIVER == 5) || \
+	(XPAR_VPHY_0_TRANSCEIVER == 6)
+	XVPHY_PRBSSEL_STD_MODE 	    = 0x0, /**< Pattern gen/mon OFF  */
+	XVPHY_PRBSSEL_PRBS7    	    = 0x1, /**< PRBS-7  */
+	XVPHY_PRBSSEL_PRBS9    	    = 0x2, /**< PRBS-9  */
+	XVPHY_PRBSSEL_PRBS15   	    = 0x3, /**< PRBS-15  */
+	XVPHY_PRBSSEL_PRBS23   	    = 0x4, /**< PRBS-23  */
+	XVPHY_PRBSSEL_PRBS31   	    = 0x5, /**< PRBS-31  */
+	XVPHY_PRBSSEL_PCIE     	    = 0x8, /**< PCIE Compliance Pattern  */
+	XVPHY_PRBSSEL_SQUARE_2UI    = 0x9, /**< Square wave with 2 UI  */
+	XVPHY_PRBSSEL_SQUARE_16UI   = 0xA, /**< Square wave with 16 UI  */
+#else
+	XVPHY_PRBSSEL_STD_MODE 	    = 0x0, /**< Pattern gen/mon OFF  */
+	XVPHY_PRBSSEL_PRBS7    	    = 0x1, /**< PRBS-7  */
+	XVPHY_PRBSSEL_PRBS15   	    = 0x2, /**< PRBS-15  */
+	XVPHY_PRBSSEL_PRBS23   	    = 0x3, /**< PRBS-23  */
+	XVPHY_PRBSSEL_PRBS31   	    = 0x4, /**< PRBS-31  */
+#endif
+} XVphy_PrbsPattern;
+
+/******************************************************************************/
+/**
+ * Callback type which represents the handler for interrupts.
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+typedef void (*XVphy_IntrHandler)(void *InstancePtr);
+
+/******************************************************************************/
+/**
+ * Callback type which represents a custom timer wait handler. This is only
+ * used for Microblaze since it doesn't have a native sleep function. To avoid
+ * dependency on a hardware timer, the default wait functionality is implemented
+ * using loop iterations; this isn't too accurate. If a custom timer handler is
+ * used, the user may implement their own wait implementation using a hardware
+ * timer (see example/) for better accuracy.
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ * @param	MicroSeconds is the number of microseconds to be passed to the
+ *		timer function.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+typedef void (*XVphy_TimerHandler)(void *InstancePtr, u32 MicroSeconds);
+
+/******************************************************************************/
+/**
+ * Generic callback type.
+ *
+ * @param	CallbackRef is a pointer to the callback reference.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+typedef void (*XVphy_Callback)(void *CallbackRef);
+
+/******************************************************************************/
+/**
+ * Error callback type.
+ *
+ * @param	CallbackRef is a pointer to the callback reference.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+typedef void (*XVphy_ErrorCallback)(void *CallbackRef);
+/**
+ * This typedef contains configuration information for CPLL/QPLL programming.
+ */
+typedef struct {
+	u8 MRefClkDiv;
+	/* Aliases for N (QPLL) and N1/N2 (CPLL). */
+	union {
+		u8 NFbDivs[2];
+		u8 NFbDiv;
+		struct {
+			u8 N1FbDiv;
+			u8 N2FbDiv;
+		};
+	};
+	u16 Cdr[5];
+	u8 IsLowerBand;
+} XVphy_PllParam;
+
+/**
+ * This typedef contains configuration information for PLL type and its
+ * reference clock.
+ */
+typedef struct {
+	/* Below members are common between CPLL/QPLL. */
+	u64 LineRateHz;				/**< The line rate for the
+							channel. */
+	union {
+		XVphy_PllParam QpllParams;
+		XVphy_PllParam CpllParams;	/**< Parameters for a CPLL. */
+		XVphy_PllParam PllParams;
+	};
+	union {
+		XVphy_PllRefClkSelType CpllRefClkSel;
+						/**< Multiplexer selection for
+							the reference clock of
+							the CPLL. */
+		XVphy_PllRefClkSelType PllRefClkSel;
+	};
+	/* Below members are CPLL specific. */
+	union {
+		struct {
+			u8 RxOutDiv;		/**< Output clock divider D for
+							the RX datapath. */
+			u8 TxOutDiv;		/**< Output clock divider D for
+							the TX datapath. */
+		};
+		u8 OutDiv[2];
+	};
+	union {
+		struct {
+			XVphy_GtState RxState;	/**< Current state of RX GT. */
+			XVphy_GtState TxState;	/**< Current state of TX GT. */
+		};
+		XVphy_GtState GtState[2];
+	};
+	union {
+		struct {
+			XVphy_ProtocolType RxProtocol;
+						/**< The protocol which the RX
+							path is used for. */
+			XVphy_ProtocolType TxProtocol;
+						/**< The protocol which the TX
+							path is used for. */
+		};
+		XVphy_ProtocolType Protocol[2];
+	};
+	union {
+		struct {
+			XVphy_SysClkDataSelType RxDataRefClkSel;
+						/**< Multiplexer selection for
+							the reference clock of
+							the RX datapath. */
+			XVphy_SysClkDataSelType TxDataRefClkSel;
+						/**< Multiplexer selection for
+							the reference clock of
+							the TX datapath. */
+		};
+		XVphy_SysClkDataSelType DataRefClkSel[2];
+	};
+	union {
+		struct {
+			XVphy_SysClkOutSelType RxOutRefClkSel;
+						/**< Multiplexer selection for
+							the reference clock of
+							the RX output clock. */
+			XVphy_SysClkOutSelType TxOutRefClkSel;
+						/**< Multiplexer selection for
+							the reference clock of
+							the TX output clock. */
+		};
+		XVphy_SysClkOutSelType OutRefClkSel[2];
+	};
+	union {
+		struct {
+			XVphy_OutClkSelType RxOutClkSel;
+						/**< Multiplexer selection for
+							which clock to use as
+							the RX output clock. */
+			XVphy_OutClkSelType TxOutClkSel;
+						/**< Multiplexer selection for
+							which clock to use as
+							the TX output clock. */
+		};
+		XVphy_OutClkSelType OutClkSel[2];
+	};
+	union {
+		struct {
+			u8 RxDelayBypass;	/**< Bypasses the delay
+							alignment block for the
+							RX output clock. */
+			u8 TxDelayBypass;	/**< Bypasses the delay
+							alignment block for the
+							TX output clock. */
+		};
+		u8 DelayBypass;
+	};
+	u8 RxDataWidth;				/**< In bits. */
+	u8 RxIntDataWidth;			/**< In bytes. */
+	u8 TxDataWidth;				/**< In bits. */
+	u8 TxIntDataWidth;			/**< In bytes. */
+} XVphy_Channel;
+
+/**
+ * This typedef contains configuration information for MMCM programming.
+ */
+typedef struct {
+	u8 DivClkDivide;
+	u8 ClkFbOutMult;
+	u16 ClkFbOutFrac;
+	u16 ClkOut0Div;
+	u16 ClkOut0Frac;
+	u16 ClkOut1Div;
+	u16 ClkOut2Div;
+} XVphy_Mmcm;
+
+/**
+ * This typedef represents a GT quad.
+ */
+typedef struct {
+	union {
+		struct {
+			XVphy_Mmcm RxMmcm;	/**< Mixed-mode clock manager
+							(MMCM) parameters for
+							RX. */
+			XVphy_Mmcm TxMmcm;	/**< MMCM parameters for TX. */
+		};
+		XVphy_Mmcm Mmcm[2];		/**< MMCM parameters. */
+	};
+	union {
+		struct {
+			XVphy_Channel Ch1;
+			XVphy_Channel Ch2;
+			XVphy_Channel Ch3;
+			XVphy_Channel Ch4;
+			XVphy_Channel Cmn0;
+			XVphy_Channel Cmn1;
+		};
+		XVphy_Channel Plls[6];
+	};
+	union {
+		struct {
+			u32 GtRefClk0Hz;
+			u32 GtRefClk1Hz;
+			u32 GtNorthRefClk0Hz;
+			u32 GtNorthRefClk1Hz;
+			u32 GtSouthRefClk0Hz;
+			u32 GtSouthRefClk1Hz;
+			u32 GtgRefClkHz;
+		};
+		u32 RefClkHz[7];
+	};
+} XVphy_Quad;
+
+#ifdef XV_VPHY_LOG_ENABLE
+/**
+ * This typedef contains the logging mechanism for debug.
+ */
+typedef struct {
+	u16 DataBuffer[256];		/**< Log buffer with event data. */
+	u8 HeadIndex;			/**< Index of the head entry of the
+						Event/DataBuffer. */
+	u8 TailIndex;			/**< Index of the tail entry of the
+						Event/DataBuffer. */
+} XVphy_Log;
+#endif
+
+/**
+ * This typedef contains configuration information for the Video PHY core.
+ */
+typedef struct {
+	u16 DeviceId;			/**< Device instance ID. */
+	UINTPTR BaseAddr;		/**< The base address of the core
+						instance. */
+	XVphy_GtType XcvrType;		/**< VPHY Transceiver Type */
+	u8 TxChannels;			/**< No. of active channels in TX */
+	u8 RxChannels;			/**< No. of active channels in RX */
+	XVphy_ProtocolType TxProtocol;	/**< Protocol which TX is used for. */
+	XVphy_ProtocolType RxProtocol;	/**< Protocol which RX is used for. */
+	XVphy_PllRefClkSelType TxRefClkSel; /**< TX REFCLK selection. */
+	XVphy_PllRefClkSelType RxRefClkSel; /**< RX REFCLK selection. */
+	XVphy_SysClkDataSelType TxSysPllClkSel; /**< TX SYSCLK selection. */
+	XVphy_SysClkDataSelType RxSysPllClkSel; /**< RX SYSCLK selectino. */
+	u8 DruIsPresent;		/**< A data recovery unit (DRU) exists
+						in the design .*/
+	XVphy_PllRefClkSelType DruRefClkSel; /**< DRU REFCLK selection. */
+	XVidC_PixelsPerClock Ppc;	/**< Number of input pixels per
+						 clock. */
+	u8 TxBufferBypass;		/**< TX Buffer Bypass is enabled in the
+						design. */
+	u8  HdmiFastSwitch;		/**< HDMI fast switching is enabled in the
+						design. */
+	u8  TransceiverWidth;	/**< Transceiver Width seeting in the design */
+	u32 ErrIrq;	            /**< Error IRQ is enalbed in design */
+	u32 AxiLiteClkFreq;	    /**< AXI Lite Clock Frequency in Hz */
+	u32 DrpClkFreq;	        /**< DRP Clock Frequency in Hz */
+	u8  UseGtAsTxTmdsClk;	/**< Use 4th GT channel as TX TMDS clock */
+} XVphy_Config;
+
+/* Forward declaration. */
+struct XVphy_GtConfigS;
+
+/**
+ * The XVphy driver instance data. The user is required to allocate a variable
+ * of this type for every XVphy device in the system. A pointer to a variable of
+ * this type is then passed to the driver API functions.
+ */
+typedef struct {
+	u32 IsReady;				/**< Device is initialized and
+							ready. */
+	XVphy_Config Config;			/**< Configuration structure for
+							the Video PHY core. */
+	const struct XVphy_GtConfigS *GtAdaptor;
+#ifdef XV_VPHY_LOG_ENABLE
+	XVphy_Log Log;				/**< A log of events. */
+#endif
+	XVphy_Quad Quads[2];			/**< The quads available to the
+							Video PHY core.*/
+	u32 HdmiRxRefClkHz;			/**< HDMI RX refclk. */
+	u32 HdmiTxRefClkHz;			/**< HDMI TX refclk. */
+	u8 HdmiRxTmdsClockRatio;		/**< HDMI TMDS clock ratio. */
+	u8 HdmiTxSampleRate;			/**< HDMI TX sample rate. */
+	u8 HdmiRxDruIsEnabled;			/**< The DRU is enabled. */
+	u8 HdmiIsQpllPresent;           /**< QPLL is present in HW */
+	XVphy_IntrHandler IntrCpllLockHandler;	/**< Callback function for CPLL
+							lock interrupts. */
+	void *IntrCpllLockCallbackRef;		/**< A pointer to the user data
+							passed to the CPLL lock
+							callback function. */
+	XVphy_IntrHandler IntrQpllLockHandler;	/**< Callback function for QPLL
+							lock interrupts. */
+	void *IntrQpllLockCallbackRef;		/**< A pointer to the user data
+							passed to the QPLL lock
+							callback function. */
+	XVphy_IntrHandler IntrQpll1LockHandler;	/**< Callback function for QPLL
+							lock interrupts. */
+	void *IntrQpll1LockCallbackRef;		/**< A pointer to the user data
+							passed to the QPLL lock
+							callback function. */
+	XVphy_IntrHandler IntrTxResetDoneHandler; /**< Callback function for TX
+							reset done lock
+							interrupts. */
+	void *IntrTxResetDoneCallbackRef;	/**< A pointer to the user data
+							passed to the TX reset
+							done lock callback
+							function. */
+	XVphy_IntrHandler IntrRxResetDoneHandler; /**< Callback function for RX
+							reset done lock
+							interrupts. */
+	void *IntrRxResetDoneCallbackRef;	/**< A pointer to the user data
+							passed to the RX reset
+							done lock callback
+							function. */
+	XVphy_IntrHandler IntrTxAlignDoneHandler; /**< Callback function for TX
+							align done lock
+							interrupts. */
+	void *IntrTxAlignDoneCallbackRef;	/**< A pointer to the user data
+							passed to the TX align
+							done lock callback
+							function. */
+	XVphy_IntrHandler IntrTxClkDetFreqChangeHandler; /**< Callback function
+							for TX clock detector
+							frequency change
+							interrupts. */
+	void *IntrTxClkDetFreqChangeCallbackRef; /**< A pointer to the user data
+							passed to the TX clock
+							detector frequency
+							change callback
+							function. */
+	XVphy_IntrHandler IntrRxClkDetFreqChangeHandler; /**< Callback function
+							for RX clock detector
+							frequency change
+							interrupts. */
+	void *IntrRxClkDetFreqChangeCallbackRef; /**< A pointer to the user data
+							passed to the RX clock
+							detector frequency
+							change callback
+							function. */
+	XVphy_IntrHandler IntrTxMmcmLockHandler; /**< Callback function
+							for TX MMCM lock
+							interrupts. */
+	void *IntrTxMmcmLockCallbackRef; /**< A pointer to the user data
+							passed to the TX MMCM lock
+							callback function. */
+	XVphy_IntrHandler IntrRxMmcmLockHandler; /**< Callback function
+							for RX MMCM lock
+							interrupts. */
+	void *IntrRxMmcmLockCallbackRef; /**< A pointer to the user data
+							passed to the RX MMCM lock
+							callback function. */
+	XVphy_IntrHandler IntrTxTmrTimeoutHandler; /**< Callback function for TX
+							timer timeout
+							interrupts. */
+	void *IntrTxTmrTimeoutCallbackRef;	/**< A pointer to the user data
+							passed to the TX timer
+							timeout callback
+							function. */
+	XVphy_IntrHandler IntrRxTmrTimeoutHandler; /**< Callback function for RX
+							timer timeout
+							interrupts. */
+	void *IntrRxTmrTimeoutCallbackRef;	/**< A pointer to the user data
+							passed to the RX timer
+							timeout callback
+							function. */
+        /* Error Condition callbacks. */
+	XVphy_ErrorCallback ErrorCallback;	/**< Callback for Error Condition. */
+	void *ErrorRef;			/**< To be passed to the Error condition
+							 callback. */
+	XVphy_ErrorCallback PllLayoutErrorCallback;	/**< Callback for Error
+							Condition. */
+	void *PllLayoutErrorRef;/**< To be passed to the Error condition
+							 callback. */
+        /* HDMI callbacks. */
+	XVphy_Callback HdmiTxInitCallback;	/**< Callback for TX init. */
+	void *HdmiTxInitRef;			/**< To be passed to the TX init
+							callback. */
+	XVphy_Callback HdmiTxReadyCallback;	/**< Callback for TX ready. */
+	void *HdmiTxReadyRef;			/**< To be passed to the TX
+							ready callback. */
+	XVphy_Callback HdmiRxInitCallback;	/**< Callback for RX init. */
+	void *HdmiRxInitRef;			/**< To be passed to the RX
+							init callback. */
+	XVphy_Callback HdmiRxReadyCallback;	/**< Callback for RX ready. */
+	void *HdmiRxReadyRef;			/**< To be passed to the RX
+							ready callback. */
+	XVphy_TimerHandler UserTimerWaitUs;	/**< Custom user function for
+							delay/sleep. */
+	void *UserTimerPtr;			/**< Pointer to a timer instance
+							used by the custom user
+							delay/sleep function. */
+} XVphy;
+
+/**************************** Function Prototypes *****************************/
+
+/* xvphy.c: Setup and initialization functions. */
+void XVphy_CfgInitialize(XVphy *InstancePtr, XVphy_Config *ConfigPtr,
+		UINTPTR EffectiveAddr);
+u32 XVphy_PllInitialize(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_PllRefClkSelType QpllRefClkSel,
+		XVphy_PllRefClkSelType CpllxRefClkSel,
+		XVphy_PllType TxPllSelect, XVphy_PllType RxPllSelect);
+#if defined (XPAR_XDP_0_DEVICE_ID)
+u32 XVphy_ClkInitialize(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir);
+#endif
+u32 XVphy_GetVersion(XVphy *InstancePtr);
+void XVphy_WaitUs(XVphy *InstancePtr, u32 MicroSeconds);
+void XVphy_SetUserTimerHandler(XVphy *InstancePtr,
+		XVphy_TimerHandler CallbackFunc, void *CallbackRef);
+
+/* xvphy.c: Channel configuration functions - setters. */
+u32 XVphy_CfgLineRate(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u64 LineRateHz);
+#if defined (XPAR_XDP_0_DEVICE_ID)
+u32 XVphy_CfgQuadRefClkFreq(XVphy *InstancePtr, u8 QuadId,
+	XVphy_PllRefClkSelType RefClkType, u32 FreqHz);
+#endif
+
+/* xvphy.c: Channel configuration functions - getters. */
+XVphy_PllType XVphy_GetPllType(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_ChannelId ChId);
+u64 XVphy_GetLineRateHz(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+
+/* xvphy.c: Reset functions. */
+#if defined (XPAR_XDP_0_DEVICE_ID)
+u32 XVphy_WaitForPmaResetDone(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir);
+u32 XVphy_WaitForResetDone(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir);
+u32 XVphy_WaitForPllLock(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+#endif
+u32 XVphy_ResetGtPll(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Hold);
+u32 XVphy_ResetGtTxRx(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Hold);
+
+/* xvphy.c: TX|RX Control functions. */
+u32 XVphy_SetPolarity(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Polarity);
+u32 XVphy_SetPrbsSel(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, XVphy_PrbsPattern Pattern);
+u32 XVphy_TxPrbsForceError(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, u8 ForceErr);
+void XVphy_SetTxVoltageSwing(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, u8 Vs);
+void XVphy_SetTxPreEmphasis(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId, u8 Pe);
+void XVphy_SetTxPostCursor(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u8 Pc);
+void XVphy_SetRxLpm(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Enable);
+
+/* xvphy.c: GT/MMCM DRP access. */
+u32 XVphy_DrpWr(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u16 Addr, u16 Val);
+u16 XVphy_DrpRd(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+        u16 Addr, u16 *RetVal);
+void XVphy_MmcmPowerDown(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir,
+		u8 Hold);
+void XVphy_MmcmStart(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir);
+void XVphy_IBufDsEnable(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir,
+		u8 Enable);
+void XVphy_Clkout1OBufTdsEnable(XVphy *InstancePtr, XVphy_DirectionType Dir,
+		u8 Enable);
+#if defined (XPAR_XDP_0_DEVICE_ID)
+void XVphy_BufgGtReset(XVphy *InstancePtr, XVphy_DirectionType Dir, u8 Reset);
+
+/* xvphy.c Miscellaneous control. */
+void XVphy_Set8b10b(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Enable);
+#endif
+u32 XVphy_IsBonded(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+
+/* xvphy.c: Error Condition. */
+void XVphy_SetErrorCallback(XVphy *InstancePtr,
+		void *CallbackFunc, void *CallbackRef);
+#if (XPAR_VPHY_0_TRANSCEIVER == 1)
+void XVphy_SetPllLayoutErrorCallback(XVphy *InstancePtr,
+		void *CallbackFunc, void *CallbackRef);
+#endif
+
+/* xvphy_log.c: Logging functions. */
+int XVphy_LogShow(XVphy *InstancePtr, char *buff, int buff_size);
+void XVphy_LogReset(XVphy *InstancePtr);
+u16 XVphy_LogRead(XVphy *InstancePtr);
+#ifdef XV_VPHY_LOG_ENABLE
+void XVphy_LogWrite(XVphy *InstancePtr, XVphy_LogEvent Evt, u8 Data);
+#else
+#define XVphy_LogWrite(...)
+#endif
+
+/* xvphy_intr.c: Interrupt handling functions. */
+void XVphy_InterruptHandler(XVphy *InstancePtr);
+
+/* xvphy_selftest.c: Self test function. */
+u32 XVphy_SelfTest(XVphy *InstancePtr);
+
+/* xvphy_sinit.c: Configuration extraction function. */
+XVphy_Config *XVphy_LookupConfig(u16 DeviceId);
+
+/* xvphy_dp.c, xvphy_hdmi.c, xvphy_hdmi_intr.c: Protocol specific functions. */
+u32 XVphy_DpInitialize(XVphy *InstancePtr, XVphy_Config *CfgPtr, u8 QuadId,
+		XVphy_PllRefClkSelType CpllRefClkSel,
+		XVphy_PllRefClkSelType QpllRefClkSel,
+		XVphy_PllType TxPllSelect, XVphy_PllType RxPllSelect,
+		u8 LinkRate);
+u32 XVphy_Hdmi_CfgInitialize(XVphy *InstancePtr, u8 QuadId,
+        XVphy_Config *CfgPtr);
+u32 XVphy_SetHdmiTxParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc,
+		XVidC_ColorFormat ColorFormat);
+u32 XVphy_SetHdmiRxParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+
+u32 XVphy_HdmiCfgCalcMmcmParam(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir,
+		XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc);
+
+void XVphy_HdmiUpdateClockSelection(XVphy *InstancePtr, u8 QuadId,
+		XVphy_SysClkDataSelType TxSysPllClkSel,
+		XVphy_SysClkDataSelType RxSysPllClkSel);
+void XVphy_ClkDetFreqReset(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir);
+u32 XVphy_ClkDetGetRefClkFreqHz(XVphy *InstancePtr, XVphy_DirectionType Dir);
+u32 XVphy_DruGetRefClkFreqHz(XVphy *InstancePtr);
+int XVphy_HdmiDebugInfo(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		char *buff, int buff_size);
+
+void XVphy_DpDebugInfo(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+void XVphy_SetHdmiCallback(XVphy *InstancePtr,
+		XVphy_HdmiHandlerType HandlerType,
+		void *CallbackFunc, void *CallbackRef);
+void XVphy_RegisterDebug(XVphy *InstancePtr);
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+#define XVPHY_CH2IDX(Id)	((Id) - XVPHY_CHANNEL_ID_CH1)
+#define XVPHY_ISCH(Id)		(((Id) == XVPHY_CHANNEL_ID_CHA) || \
+	((XVPHY_CHANNEL_ID_CH1 <= (Id)) && ((Id) <= XVPHY_CHANNEL_ID_CH4)))
+#define XVPHY_ISCMN(Id)		(((Id) == XVPHY_CHANNEL_ID_CMNA) || \
+	((XVPHY_CHANNEL_ID_CMN0 <= (Id)) && ((Id) <= XVPHY_CHANNEL_ID_CMN1)))
+#define XVPHY_ISTXMMCM(Id)	((Id) == XVPHY_CHANNEL_ID_TXMMCM)
+#define XVPHY_ISRXMMCM(Id)	((Id) == XVPHY_CHANNEL_ID_RXMMCM)
+
+#define XVphy_IsTxUsingQpll(InstancePtr, QuadId, ChId) \
+        ((XVPHY_PLL_TYPE_QPLL == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId)) || \
+        (XVPHY_PLL_TYPE_QPLL0 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId)) || \
+        (XVPHY_PLL_TYPE_QPLL1 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId)) || \
+	(XVPHY_PLL_TYPE_PLL0 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId)) || \
+	(XVPHY_PLL_TYPE_PLL1 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId)))
+#define XVphy_IsRxUsingQpll(InstancePtr, QuadId, ChId) \
+        ((XVPHY_PLL_TYPE_QPLL == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId)) || \
+        (XVPHY_PLL_TYPE_QPLL0 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId)) || \
+        (XVPHY_PLL_TYPE_QPLL1 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId)) || \
+	(XVPHY_PLL_TYPE_PLL0 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId)) || \
+	(XVPHY_PLL_TYPE_PLL1 == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId)))
+#define XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId) \
+        (XVPHY_PLL_TYPE_CPLL == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId))
+#define XVphy_IsRxUsingCpll(InstancePtr, QuadId, ChId) \
+        (XVPHY_PLL_TYPE_CPLL == \
+		XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId))
+
+#define XVPHY_GTXE2 1
+#define XVPHY_GTHE2 2
+#define XVPHY_GTPE2 3
+#define XVPHY_GTHE3 4
+#define XVPHY_GTHE4 5
+#define XVPHY_GTYE4 6
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XVPHY_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_gt.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_gt.h
@@ -0,0 +1,130 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_gt.h
+ *
+ * The Xilinx Video PHY (VPHY) driver. This driver supports the Xilinx Video PHY
+ * IP core.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Added Gtpe2Config and Gtpe4Config variables.
+ * 1.4   gm   29/11/16 Added preprocessor directives for sw footprint reduction
+ *                     Changed TX reconfig hook from TxPllRefClkDiv1Reconfig to
+ *                       TxChReconfig
+ *                     Fixed c++ compiler warnings
+ *                     Added xcvr adaptor functions for C++ compilations
+ * 1.7   gm   13/09/17 Added GTYE4 support
+ * </pre>
+ *
+ * @{
+*******************************************************************************/
+
+#ifndef XVPHY_GT_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XVPHY_GT_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xvphy.h"
+#include "xvphy_i.h"
+#include "xil_assert.h"
+
+/****************************** Type Definitions ******************************/
+
+typedef struct {
+	const u8 *M;
+	const u8 *N1;
+	const u8 *N2;
+	const u8 *D;
+} XVphy_GtPllDivs;
+
+typedef struct XVphy_GtConfigS {
+	u32 (*CfgSetCdr)(XVphy *, u8, XVphy_ChannelId);
+	u32 (*CheckPllOpRange)(XVphy *, u8, XVphy_ChannelId, u64);
+	u32 (*OutDivChReconfig)(XVphy *, u8, XVphy_ChannelId,
+			XVphy_DirectionType);
+	u32 (*ClkChReconfig)(XVphy *, u8, XVphy_ChannelId);
+	u32 (*ClkCmnReconfig)(XVphy *, u8, XVphy_ChannelId);
+	u32 (*RxChReconfig)(XVphy *, u8, XVphy_ChannelId);
+	u32 (*TxChReconfig)(XVphy *, u8, XVphy_ChannelId);
+
+	XVphy_GtPllDivs CpllDivs;
+	XVphy_GtPllDivs QpllDivs;
+} XVphy_GtConfig;
+
+/******************* Macros (Inline Functions) Definitions ********************/
+#ifdef __cplusplus
+u32 XVphy_CfgSetCdr(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+u32 XVphy_CheckPllOpRange(XVphy *InstancePtr, u8 QuadId,
+							XVphy_ChannelId ChId, u64 PllClkOutFreqHz);
+u32 XVphy_OutDivChReconfig(XVphy *InstancePtr, u8 QuadId,
+							XVphy_ChannelId ChId, XVphy_DirectionType Dir);
+u32 XVphy_ClkChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+u32 XVphy_ClkCmnReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+u32 XVphy_RxChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+u32 XVphy_TxChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+#else
+#define XVphy_CfgSetCdr(Ip, ...) \
+		((Ip)->GtAdaptor->CfgSetCdr(Ip, __VA_ARGS__))
+#define XVphy_CheckPllOpRange(Ip, ...) \
+		((Ip)->GtAdaptor->CheckPllOpRange(Ip, __VA_ARGS__))
+#define XVphy_OutDivChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->OutDivChReconfig(Ip, __VA_ARGS__))
+#define XVphy_ClkChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->ClkChReconfig(Ip, __VA_ARGS__))
+#define XVphy_ClkCmnReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->ClkCmnReconfig(Ip, __VA_ARGS__))
+#define XVphy_RxChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->RxChReconfig(Ip, __VA_ARGS__))
+#define XVphy_TxChReconfig(Ip, ...) \
+		((Ip)->GtAdaptor->TxChReconfig(Ip, __VA_ARGS__))
+#endif
+
+/*************************** Variable Declarations ****************************/
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+extern const XVphy_GtConfig Gtxe2Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+extern const XVphy_GtConfig Gthe2Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+extern const XVphy_GtConfig Gtpe2Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+extern const XVphy_GtConfig Gthe3Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+extern const XVphy_GtConfig Gthe4Config;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+extern const XVphy_GtConfig Gtye4Config;
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XVPHY_GT_H_ */
+/** @} */
\ No newline at end of file
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_gthe4.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_gthe4.c
@@ -0,0 +1,1353 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_gthe4.c
+ *
+ * Contains a minimal set of functions for the XVphy driver that allow access
+ * to all of the Video PHY core's functionality. See xvphy.h for a detailed
+ * description of the driver.
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  19/10/15 Initial release.
+ * 1.1   gm   18/03/16 Added XVphy_Gthe4RxPllRefClkDiv1Reconfig function
+ *                     Added XVphy_Gthe4TxChReconfig function
+ *                     Corrected RXCDRCFG2 values
+ * 1.2   gm   26/08/16 Suppressed warning messages due to unused arguments
+ * 1.4   gm   29/11/16 Added preprocessor directives for sw footprint reduction
+ *                     Changed TX reconfig hook from TxPllRefClkDiv1Reconfig to
+ *                       TxChReconfig
+ *                     Added TX datawidth dynamic reconfiguration
+ *                     Added N2=8 divider for CPLL for DP
+ *                     Added CPLL_CFGx reconfiguration in
+ *                       XVphy_Gthe4ClkChReconfig API
+ *                     Corrected the default return value of DRP encoding
+ *                       APIs to prevent overwritting the reserved bits
+ * 1.5   gm   27/04/17 Updated the RXPI_CFG0 according to new GTWiz rules
+ *                     Corrected RXCDR_CFG values for DP
+ *                     Added XVphy_CfgCpllCalPeriodandTol API
+ * 1.6   gm   12/06/17 Changed XVphy_DrpRead with XVphy_DrpRd
+ *                     Changed XVphy_DrpWrite with XVphy_DrpWr
+ *                     Improved status return of APIs with DRP Rd and Wr
+ *                     Added N2=8 divider for CPLL for HDMI
+ * 1.7   gm   13/09/17 Disabled intelligent clock sel in QPLL0/1 configuration
+ *                     Updated DP CDR config for 8.1 Gbps
+ *                     Updated XVPHY_QPLL0_MAX to 16375000000LL
+ * 1.8   gm   05/09/18 Enable IPS only when XVphy_GetRefClkSourcesCount
+ *                       returns more than 1.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xvphy_gt.h"
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+#include "xstatus.h"
+
+/**************************** Function Prototypes *****************************/
+
+static u8 XVphy_MToDrpEncoding(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId);
+static u16 XVphy_NToDrpEncoding(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId, u8 NId);
+static u8 XVphy_DToDrpEncoding(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId, XVphy_DirectionType Dir);
+static u8 XVphy_DrpEncodeQpllMCpllMN2(u8 AttrEncode);
+static u8 XVphy_DrpEncodeCpllN1(u8 AttrEncode);
+static u8 XVphy_DrpEncodeCpllTxRxD(u8 AttrEncode);
+static u16 XVphy_DrpEncodeQpllN(u8 AttrEncode);
+static u8 Xvphy_DrpEncodeDataWidth(u8 AttrEncode);
+static u8 Xvphy_DrpEncodeIntDataWidth(u8 AttrEncode);
+static u16 XVphy_DrpEncodeClk25(u32 RefClkFreqHz);
+
+u32 XVphy_Gthe4CfgSetCdr(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+u32 XVphy_Gthe4CheckPllOpRange(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId, u64 PllClkOutFreqHz);
+u32 XVphy_Gthe4OutDivChReconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId, XVphy_DirectionType Dir);
+u32 XVphy_Gthe4ClkChReconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId);
+u32 XVphy_Gthe4ClkCmnReconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId CmnId);
+u32 XVphy_Gthe4RxChReconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId);
+u32 XVphy_Gthe4TxChReconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId);
+u32 XVphy_Gthe4TxPllRefClkDiv1Reconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId);
+u32 XVphy_Gthe4RxPllRefClkDiv1Reconfig(XVphy *InstancePtr, u8 QuadId,
+        XVphy_ChannelId ChId);
+
+/************************** Constant Definitions ******************************/
+
+/* DRP register space. */
+#define XVPHY_DRP_RXCDR_CFG(n)		(0x0E + n)
+#define XVPHY_DRP_RXCDR_CFG_GEN3(n)	(0xA2 + n)
+#define XVPHY_DRP_RXCDR_CFG_GEN4(n)	(0x119 + n)
+
+#define XVPHY_DRP_CPLL_FBDIV		0x28
+#define XVPHY_DRP_CPLL_REFCLK_DIV	0x2A
+#define XVPHY_DRP_RXOUT_DIV		0x63
+#define XVPHY_DRP_RXCLK25		0x6D
+#define XVPHY_DRP_TXCLK25		0x7A
+#define XVPHY_DRP_TXOUT_DIV		0x7C
+#define XVPHY_DRP_QPLL1_FBDIV		0x94
+#define XVPHY_DRP_QPLL1_REFCLK_DIV	0x98
+#define XVPHY_DRP_RXCDR_CFG_WORD0	0x0E
+#define XVPHY_DRP_RXCDR_CFG_WORD1	0x0F
+#define XVPHY_DRP_RXCDR_CFG_WORD2	0x10
+#define XVPHY_DRP_RXCDR_CFG_WORD3	0x11
+#define XVPHY_DRP_RXCDR_CFG_WORD4	0x12
+
+/* PLL operating ranges. */
+#define XVPHY_QPLL0_MIN		 9800000000LL
+#define XVPHY_QPLL0_MAX		16375000000LL
+#define XVPHY_QPLL1_MIN		 8000000000LL
+#define XVPHY_QPLL1_MAX		13000000000LL
+#define XVPHY_CPLL_MIN		 2000000000LL
+#define XVPHY_CPLL_MAX		 6250000000LL
+
+const u8 Gthe4CpllDivsM[]	= {1, 2, 0};
+const u8 Gthe4CpllDivsN1[]	= {4, 5, 0};
+const u8 Gthe4CpllDivsN2[]	= {1, 2, 3, 4, 5, 8, 0};
+const u8 Gthe4CpllDivsD[]	= {1, 2, 4, 8, 0};
+
+const u8 Gthe4QpllDivsM[]	= {4, 3, 2, 1, 0};
+const u8 Gthe4QpllDivsN1[]	= {16, 20, 32, 40, 60, 64, 66, 75, 80, 84, 90,
+				   96, 100, 112, 120, 125, 150, 160, 0};
+const u8 Gthe4QpllDivsN2[]	= {1, 0};
+const u8 Gthe4QpllDivsD[]	= {16, 8, 4, 2, 1, 0};
+
+const XVphy_GtConfig Gthe4Config = {
+	.CfgSetCdr = XVphy_Gthe4CfgSetCdr,
+	.CheckPllOpRange = XVphy_Gthe4CheckPllOpRange,
+	.OutDivChReconfig = XVphy_Gthe4OutDivChReconfig,
+	.ClkChReconfig = XVphy_Gthe4ClkChReconfig,
+	.ClkCmnReconfig = XVphy_Gthe4ClkCmnReconfig,
+	.RxChReconfig = XVphy_Gthe4RxChReconfig,
+	.TxChReconfig = XVphy_Gthe4TxChReconfig,
+
+	.CpllDivs = {
+		.M = Gthe4CpllDivsM,
+		.N1 = Gthe4CpllDivsN1,
+		.N2 = Gthe4CpllDivsN2,
+		.D = Gthe4CpllDivsD,
+	},
+	.QpllDivs = {
+		.M = Gthe4QpllDivsM,
+		.N1 = Gthe4QpllDivsN1,
+		.N2 = Gthe4QpllDivsN2,
+		.D = Gthe4QpllDivsD,
+	},
+};
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function will set the clock and data recovery (CDR) values for a given
+* channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4CfgSetCdr(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	XVphy_Channel *ChPtr;
+	u32 Status = XST_SUCCESS;
+	u64 LineRateHz;
+
+	/* Set CDR values only for CPLLs. */
+	if ((ChId < XVPHY_CHANNEL_ID_CH1) || (ChId > XVPHY_CHANNEL_ID_CH4)) {
+		return XST_FAILURE;
+	}
+
+	/* This is DP specific. */
+	ChPtr = &InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)];
+
+	ChPtr->PllParams.Cdr[0] = 0x0000;
+	ChPtr->PllParams.Cdr[1] = 0x0000;
+	ChPtr->PllParams.Cdr[3] = 0x0000;
+	ChPtr->PllParams.Cdr[4] = 0x0000;
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		/* RxOutDiv = 1  => Cdr[2] = 0x0269
+		 * RxOutDiv = 2  => Cdr[2] = 0x0259
+		 * RxOutDiv = 4  => Cdr[2] = 0x0249
+		 * RxOutDiv = 8  => Cdr[2] = 0x0239
+		 * RxOutDiv = 16 => Cdr[2] = 0x0229 */
+		ChPtr->PllParams.Cdr[2] = 0x0269;
+		while (ChPtr->RxOutDiv >>= 1) {
+			ChPtr->PllParams.Cdr[2] -= 0x10;
+		}
+		/* Restore RxOutDiv. */
+		ChPtr->RxOutDiv = 1 << ((0x0269 - ChPtr->PllParams.Cdr[2]) >> 4);
+	} else {
+		Status = XST_FAILURE;
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will check if a given PLL output frequency is within the
+* operating range of the PLL for the GT type.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	PllClkOutFreqHz is the frequency to check.
+*
+* @return
+*		- XST_SUCCESS if the frequency resides within the PLL's range.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4CheckPllOpRange(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, u64 PllClkOutFreqHz)
+{
+	u32 Status = XST_FAILURE;
+
+	/* Suppress Warning Messages */
+	InstancePtr = InstancePtr;
+	QuadId = QuadId;
+
+	if (((ChId == XVPHY_CHANNEL_ID_CMN0) &&
+			(XVPHY_QPLL0_MIN <= PllClkOutFreqHz) &&
+			(PllClkOutFreqHz <= XVPHY_QPLL0_MAX)) ||
+	    ((ChId == XVPHY_CHANNEL_ID_CMN1) &&
+			(XVPHY_QPLL1_MIN <= PllClkOutFreqHz) &&
+			(PllClkOutFreqHz <= XVPHY_QPLL1_MAX)) ||
+	    ((ChId >= XVPHY_CHANNEL_ID_CH1) &&
+			(ChId <= XVPHY_CHANNEL_ID_CH4) &&
+			(XVPHY_CPLL_MIN <= PllClkOutFreqHz) &&
+			(PllClkOutFreqHz <= XVPHY_CPLL_MAX))) {
+		Status = XST_SUCCESS;
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the output divider logic for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4OutDivChReconfig(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir)
+{
+	u16 DrpVal;
+	u16 WriteVal;
+    u32 Status = XST_SUCCESS;
+
+	if (Dir == XVPHY_DIR_RX) {
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x63, &DrpVal);
+		/* Mask out RX_OUT_DIV. */
+		DrpVal &= ~0x07;
+		/* Set RX_OUT_DIV. */
+		WriteVal = (XVphy_DToDrpEncoding(InstancePtr, QuadId, ChId,
+				XVPHY_DIR_RX) & 0x7);
+		DrpVal |= WriteVal;
+		/* Write new DRP register value for RX dividers. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x63, DrpVal);
+	}
+	else {
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x7C, &DrpVal);
+		/* Mask out TX_OUT_DIV. */
+		DrpVal &= ~0x700;
+		/* Set TX_OUT_DIV. */
+		WriteVal = (XVphy_DToDrpEncoding(InstancePtr, QuadId, ChId,
+				XVPHY_DIR_TX) & 0x7);
+		DrpVal |= (WriteVal << 8);
+		/* Write new DRP register value for RX dividers. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x7C, DrpVal);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the channel clock settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4ClkChReconfig(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId)
+{
+	u16 DrpVal;
+	u16 WriteVal;
+	u32 CpllxVcoRateMHz;
+    u32 Status = XST_SUCCESS;
+
+	/* Obtain current DRP register value for PLL dividers. */
+	Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x28, &DrpVal);
+	/* Mask out clock divider bits. */
+	DrpVal &= ~(0xFF80);
+	/* Set CPLL_FBDIV. */
+	WriteVal = (XVphy_NToDrpEncoding(InstancePtr, QuadId, ChId, 2) & 0xFF);
+	DrpVal |= (WriteVal << 8);
+	/* Set CPLL_FBDIV_45. */
+	WriteVal = (XVphy_NToDrpEncoding(InstancePtr, QuadId, ChId, 1) & 0x1);
+	DrpVal |= (WriteVal << 7);
+	/* Write new DRP register value for PLL dividers. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x28, DrpVal);
+
+	/* Write CPLL Ref Clk Div. */
+	Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x2A, &DrpVal);
+	/* Mask out clock divider bits. */
+	DrpVal &= ~(0xF800);
+	/* Set CPLL_REFCLKDIV. */
+	WriteVal = (XVphy_MToDrpEncoding(InstancePtr, QuadId, ChId) & 0x1F);
+	DrpVal |= (WriteVal << 11);
+	/* Write new DRP register value for PLL dividers. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x2A, DrpVal);
+
+	CpllxVcoRateMHz = XVphy_GetPllVcoFreqHz(InstancePtr, QuadId, ChId,
+			XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId) ?
+					XVPHY_DIR_TX : XVPHY_DIR_RX) / 1000000;
+
+	/* CPLL_CFG0 */
+	if (CpllxVcoRateMHz <= 3000) {
+		DrpVal = 0x01FA;
+	}
+	else if (CpllxVcoRateMHz <= 4250) {
+		DrpVal = 0x0FFA;
+	}
+	else {
+		DrpVal = 0x03FE;
+	}
+	/* Write new DRP register value for CPLL_CFG0. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0xCB, DrpVal);
+
+	/* CPLL_CFG1 */
+	if (CpllxVcoRateMHz <= 3000) {
+		DrpVal = 0x0023;
+	}
+	else {
+		DrpVal = 0x0021;
+	}
+	/* Write new DRP register value for CPLL_CFG1. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0xCC, DrpVal);
+
+	/* CPLL_CFG2 */
+	if (CpllxVcoRateMHz <= 3000) {
+		DrpVal = 0x0002;
+	}
+	else if (CpllxVcoRateMHz <= 4250) {
+		DrpVal = 0x0202;
+	}
+	else {
+		DrpVal = 0x0203;
+	}
+	/* Write new DRP register value for CPLL_CFG2. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0xBC, DrpVal);
+
+	/* Configure CPLL Calibration Registers */
+	XVphy_CfgCpllCalPeriodandTol(InstancePtr, QuadId, ChId,
+			(XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId) ?
+								XVPHY_DIR_TX : XVPHY_DIR_RX),
+			InstancePtr->Config.DrpClkFreq);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the common channel clock settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	CmnId is the common channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4ClkCmnReconfig(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId CmnId)
+{
+	u16 DrpVal;
+	u16 WriteVal;
+	u32 QpllxVcoRateMHz;
+	u32 QpllxClkOutMHz;
+    u32 Status = XST_SUCCESS;
+
+	/* Obtain current DRP register value for QPLLx_FBDIV. */
+	Status |= XVphy_DrpRd(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x14 : 0x94, &DrpVal);
+	/* Mask out QPLLx_FBDIV. */
+	DrpVal &= ~(0xFF);
+	/* Set QPLLx_FBDIV. */
+	WriteVal = (XVphy_NToDrpEncoding(InstancePtr, QuadId, CmnId, 0) & 0xFF);
+	DrpVal |= WriteVal;
+	/* Write new DRP register value for QPLLx_FBDIV. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x14 : 0x94, DrpVal);
+
+	/* Obtain current DRP register value for QPLLx_REFCLK_DIV. */
+	Status |= XVphy_DrpRd(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x18 : 0x98, &DrpVal);
+	/* Mask out QPLLx_REFCLK_DIV. */
+	DrpVal &= ~(0xF80);
+	/* Disable Intelligent Reference Clock Selection */
+	if (XVphy_GetRefClkSourcesCount(InstancePtr) > 1) {
+		DrpVal |= (1 << 6);
+	}
+	/* Set QPLLx_REFCLK_DIV. */
+	WriteVal = (XVphy_MToDrpEncoding(InstancePtr, QuadId, CmnId) & 0x1F);
+	DrpVal |= (WriteVal << 7);
+	/* Write new DRP register value for QPLLx_REFCLK_DIV. */
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x18 : 0x98, DrpVal);
+
+	if ((XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) ||
+		(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX))) {
+
+		QpllxVcoRateMHz = XVphy_GetPllVcoFreqHz(InstancePtr, QuadId, CmnId,
+				XVphy_IsTxUsingQpll(InstancePtr, QuadId, CmnId) ?
+						XVPHY_DIR_TX : XVPHY_DIR_RX) / 1000000;
+		QpllxClkOutMHz = QpllxVcoRateMHz / 2;
+
+		/* PPFx_CFG */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+                (CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x0D : 0x8D, &DrpVal);
+		DrpVal &= ~(0x0FC0);
+		/* PPF_MUX_CRNT_CTRL0 */
+		if (QpllxVcoRateMHz >= 15000) {
+			DrpVal |= 0x0E00;
+		}
+		else if (QpllxVcoRateMHz >= 11000) {
+			DrpVal |= 0x0800;
+		}
+		else if (QpllxVcoRateMHz >= 7000) {
+			DrpVal |= 0x0600;
+		}
+		else {
+			DrpVal |= 0x0400;
+		}
+		/* PPF_MUX_TERM_CTRL0 */
+		if (QpllxVcoRateMHz >= 13000) {
+			DrpVal |= 0x0100;
+		}
+		else {
+			DrpVal |= 0x0000;
+		}
+		/* Write new DRP register value for PPFx_CFG. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x0D : 0x8D, DrpVal);
+
+		/* QPLLx_CP */
+		if (InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+				PllParams.NFbDiv <= 40) {
+			DrpVal = 0x007F;
+		}
+		else {
+			DrpVal = 0x03FF;
+		}
+		/* Write new DRP register value for QPLLx_CP. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x16 : 0x96, DrpVal);
+
+		/* QPLLx_LPF */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+            (CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x19 : 0x99, &DrpVal);
+		DrpVal &= ~(0x0003);
+		if (InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+				PllParams.NFbDiv <= 40) {
+			DrpVal |= 0x3;
+		}
+		else {
+			DrpVal |= 0x1;
+		}
+		/* Write new DRP register value for QPLLx_LPF. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x19 : 0x99, DrpVal);
+
+		/* QPLLx_CFG4 */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+            (CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x30 : 0xB0, &DrpVal);
+		DrpVal &= ~(0x00E7);
+		/* Q_TERM_CLK */
+		if (QpllxClkOutMHz >= 7500) {
+			DrpVal |= 0x2 << 5;
+		}
+		else if (QpllxClkOutMHz >= 3500) {
+			DrpVal |= 0x0 << 5;
+		}
+		else {
+			DrpVal |= 0x6 << 5;
+		}
+		/* Q_DCRNT_CLK */
+		if (QpllxClkOutMHz >= 7500) {
+			DrpVal |= 0x5;
+		}
+		else if (QpllxClkOutMHz >= 5500) {
+			DrpVal |= 0x4;
+		}
+		else {
+			DrpVal |= 0x3;
+		}
+		/* Write new DRP register value for QPLLx_CFG4. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMN,
+			(CmnId == XVPHY_CHANNEL_ID_CMN0) ? 0x30 : 0xB0, DrpVal);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the channel's RX settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4RxChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	XVphy_Channel *ChPtr;
+	u16 DrpVal;
+	u16 WriteVal;
+	u8 CfgIndex;
+	XVphy_ChannelId ChIdPll;
+	XVphy_PllType PllType;
+	u32 PllxVcoRateMHz;
+	u32 PllxClkOutMHz;
+	u32 PllxClkOutDiv;
+    u32 Status = XST_SUCCESS;
+
+	ChPtr = &InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)];
+
+	/* RXCDR_CFG(CfgIndex) */
+	for (CfgIndex = 0; CfgIndex < 5; CfgIndex++) {
+		DrpVal = ChPtr->PllParams.Cdr[CfgIndex];
+		if (!DrpVal) {
+			/* Don't modify RX_CDR configuration. */
+			continue;
+		}
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId,
+				XVPHY_DRP_RXCDR_CFG(CfgIndex), DrpVal);
+		if (CfgIndex == 2) {
+			Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId,
+					XVPHY_DRP_RXCDR_CFG_GEN3(CfgIndex), DrpVal);
+			Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId,
+					XVPHY_DRP_RXCDR_CFG_GEN4(CfgIndex), DrpVal);
+
+		}
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		/* RX_INT_DATAWIDTH */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x66, &DrpVal);
+		DrpVal &= ~(0x3);
+		WriteVal = (Xvphy_DrpEncodeIntDataWidth(ChPtr->RxIntDataWidth) & 0x3);
+		DrpVal |= WriteVal;
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x66, DrpVal);
+
+		/* RX_DATA_WIDTH */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x03, &DrpVal);
+		DrpVal &= ~(0x1E0);
+		WriteVal = (Xvphy_DrpEncodeDataWidth(ChPtr->RxDataWidth) & 0xF);
+		WriteVal <<= 5;
+		DrpVal |= WriteVal;
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x03, DrpVal);
+
+		/* Determine PLL type. */
+		PllType = XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_RX, ChId);
+		/* Determine which channel(s) to operate on. */
+		switch (PllType) {
+			case XVPHY_PLL_TYPE_QPLL:
+			case XVPHY_PLL_TYPE_QPLL0:
+			case XVPHY_PLL_TYPE_PLL0:
+				ChIdPll = XVPHY_CHANNEL_ID_CMN0;
+				PllxClkOutDiv = 2;
+				break;
+			case XVPHY_PLL_TYPE_QPLL1:
+			case XVPHY_PLL_TYPE_PLL1:
+				ChIdPll = XVPHY_CHANNEL_ID_CMN1;
+				PllxClkOutDiv = 2;
+				break;
+			default:
+				ChIdPll = ChId;
+				PllxClkOutDiv = 1;
+				break;
+		}
+
+		PllxVcoRateMHz = XVphy_GetPllVcoFreqHz(InstancePtr, QuadId, ChIdPll,
+				XVPHY_DIR_RX) / 1000000;
+		PllxClkOutMHz = PllxVcoRateMHz / PllxClkOutDiv;
+
+		/* CH_HSPMUX_RX */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x116, &DrpVal);
+		DrpVal &= ~(0x00FF);
+		if (PllxClkOutMHz >= 7500) {
+			DrpVal |= 0x68;
+		}
+		else if (PllxClkOutMHz >= 5500) {
+			DrpVal |= 0x44;
+		}
+		else if (PllxClkOutMHz >= 3500) {
+			DrpVal |= 0x24;
+		}
+		else {
+			DrpVal |= 0x3C;
+		}
+		/* Write new DRP register value for CH_HSPMUX_RX. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x116, DrpVal);
+
+		/* PREIQ_FREQ_BST */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0xFB, &DrpVal);
+		DrpVal &= ~(0x0030);
+		if (PllxClkOutMHz > 14110) {
+			DrpVal |= 3 << 4;
+		}
+		else if (PllxClkOutMHz >= 14000) {
+			DrpVal |= 2 << 4; /* LPM Mode */
+		}
+		else if (PllxClkOutMHz >= 10000) {
+			DrpVal |= 2 << 4;
+		}
+		else if (PllxClkOutMHz >= 6000) {
+			DrpVal |= 1 << 4;
+		}
+		/* Write new DRP register value for PREIQ_FREQ_BST. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0xFB, DrpVal);
+
+		/* RXPI_CFG0 */
+		if (PllxClkOutMHz > 7000) {
+			DrpVal = 0x0004;
+		}
+		else if (PllxClkOutMHz >= 6500) {
+			DrpVal = 0x0104;
+		}
+		else if (PllxClkOutMHz >= 5500) {
+			DrpVal = 0x2004;
+		}
+		else if (PllxClkOutMHz >= 5156) {
+			DrpVal = 0x0002;
+		}
+		else if (PllxClkOutMHz >= 4500) {
+			DrpVal = 0x0102;
+		}
+		else if (PllxClkOutMHz >= 4000) {
+			DrpVal = 0x2102;
+		}
+		else if (PllxClkOutMHz >= 3500) {
+			DrpVal = 0x2202;
+		}
+		else if (PllxClkOutMHz >= 3000) {
+			DrpVal = 0x0200;
+		}
+		else if (PllxClkOutMHz >= 2500) {
+			DrpVal = 0x1300;
+		}
+		else {
+			DrpVal = 0x3300;
+		}
+		/* Write new DRP register value for RXPI_CFG0. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x9D, DrpVal);
+
+		/* RXPI_CFG1 */
+		if (PllxClkOutMHz >= 5500) {
+			DrpVal = 0x0000;
+		}
+		else if (PllxClkOutMHz >= 4500) {
+			DrpVal = 0x0015;
+		}
+		else if (PllxClkOutMHz >= 3500) {
+			DrpVal = 0x0045;
+		}
+		else if (PllxClkOutMHz >= 2000) {
+			DrpVal = 0x00FD;
+		}
+		else {
+			DrpVal = 0x00FF;
+		}
+		/* Write new DRP register value for RXPI_CFG1. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x100, DrpVal);
+	}
+
+	Status |= XVphy_Gthe4RxPllRefClkDiv1Reconfig(InstancePtr, QuadId, ChId);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the channel's TX settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4TxChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	XVphy_Channel *ChPtr;
+	u32 ReturnVal;
+	u16 DrpVal;
+	u16 WriteVal;
+	XVphy_ChannelId ChIdPll;
+	XVphy_PllType PllType;
+	u32 PllxVcoRateMHz;
+	u32 PllxClkOutMHz;
+	u32 PllxClkOutDiv;
+    u32 Status = XST_SUCCESS;
+
+	ReturnVal = XVphy_Gthe4TxPllRefClkDiv1Reconfig(InstancePtr, QuadId, ChId);
+	if (!XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+		return ReturnVal;
+	}
+
+	/* Determine PLL type. */
+	PllType = XVphy_GetPllType(InstancePtr, QuadId, XVPHY_DIR_TX, ChId);
+	/* Determine which channel(s) to operate on. */
+	switch (PllType) {
+		case XVPHY_PLL_TYPE_QPLL:
+		case XVPHY_PLL_TYPE_QPLL0:
+		case XVPHY_PLL_TYPE_PLL0:
+			ChIdPll = XVPHY_CHANNEL_ID_CMN0;
+			PllxClkOutDiv = 2;
+			break;
+		case XVPHY_PLL_TYPE_QPLL1:
+		case XVPHY_PLL_TYPE_PLL1:
+			ChIdPll = XVPHY_CHANNEL_ID_CMN1;
+			PllxClkOutDiv = 2;
+			break;
+		default:
+			ChIdPll = ChId;
+			PllxClkOutDiv = 1;
+			break;
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+
+		ChPtr = &InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)];
+		/* TX_INT_DATAWIDTH */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x85, &DrpVal);
+		DrpVal &= ~(0x3 << 10);
+		WriteVal = ((Xvphy_DrpEncodeIntDataWidth(ChPtr->
+						TxIntDataWidth) & 0x3) << 10);
+		DrpVal |= WriteVal;
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x85, DrpVal);
+
+		/* TX_DATA_WIDTH */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x7A, &DrpVal);
+		DrpVal &= ~(0xF);
+		WriteVal = (Xvphy_DrpEncodeDataWidth(ChPtr->TxDataWidth) & 0xF);
+		DrpVal |= WriteVal;
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x7A, DrpVal);
+
+		PllxVcoRateMHz = XVphy_GetPllVcoFreqHz(InstancePtr, QuadId, ChIdPll,
+				XVPHY_DIR_TX) / 1000000;
+		PllxClkOutMHz = PllxVcoRateMHz / PllxClkOutDiv;
+
+		/* TXPI_CFG */
+		if (PllxClkOutMHz >= 5500) {
+			DrpVal = 0x0000;
+		}
+		else if (PllxClkOutMHz >= 3500) {
+			DrpVal = 0x0054;
+		}
+		else {
+			DrpVal = 0x03DF;
+		}
+		/* Write new DRP register value for TXPI_CFG. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0xFF, DrpVal);
+
+		/* TXPI_CFG3 */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x9C, &DrpVal);
+		DrpVal &= ~(0x0040);
+		if (PllxClkOutMHz < 7500 && PllxClkOutMHz >= 5500) {
+			DrpVal |= 1 << 6;
+		}
+		/* Write new DRP register value for TXPI_CFG3. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x9C, DrpVal);
+
+		/* TX_PI_BIASSET */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0xFB, &DrpVal);
+		DrpVal &= ~(0x0006);
+		if (PllxClkOutMHz >= 7500) {
+			DrpVal |= 3 << 1;
+		}
+		else if (PllxClkOutMHz >= 5500) {
+			DrpVal |= 2 << 1;
+		}
+		else if (PllxClkOutMHz >= 3500) {
+			DrpVal |= 1 << 1;
+		}
+		/* Write new DRP register value for TX_PI_BIASSET. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0xFB, DrpVal);
+
+		/* CH_HSPMUX_TX */
+		Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, 0x116, &DrpVal);
+		DrpVal &= ~(0xFF00);
+		if (PllxClkOutMHz >= 7500) {
+			DrpVal |= 0x68 << 8;
+		}
+		else if (PllxClkOutMHz >= 5500) {
+			DrpVal |= 0x44 << 8;
+		}
+		else if (PllxClkOutMHz >= 3500) {
+			DrpVal |= 0x24 << 8;
+		}
+		else {
+			DrpVal |= 0x3C << 8;
+		}
+		/* Write new DRP register value for CH_HSPMUX_TX. */
+		Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x116, DrpVal);
+	}
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the channel's TX CLKDIV1 settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4TxPllRefClkDiv1Reconfig(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId)
+{
+	u16 DrpVal;
+	u32 TxRefClkHz;
+    u32 Status = XST_SUCCESS;
+	XVphy_Channel *PllPtr = &InstancePtr->Quads[QuadId].
+                    Plls[XVPHY_CH2IDX(ChId)];
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+		TxRefClkHz = InstancePtr->HdmiTxRefClkHz;
+	}
+	else {
+		TxRefClkHz = XVphy_GetQuadRefClkFreq(InstancePtr, QuadId,
+								PllPtr->PllRefClkSel);
+	}
+
+	Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, XVPHY_DRP_TXCLK25,
+                    &DrpVal);
+	DrpVal &= ~(0xF800);
+	DrpVal |= XVphy_DrpEncodeClk25(TxRefClkHz) << 11;
+    Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, XVPHY_DRP_TXCLK25,
+				DrpVal);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will configure the channel's RX CLKDIV1 settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Gthe4RxPllRefClkDiv1Reconfig(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId)
+{
+	u16 DrpVal;
+	u32 RxRefClkHz;
+    u32 Status = XST_SUCCESS;
+	XVphy_Channel *PllPtr = &InstancePtr->Quads[QuadId].
+                    Plls[XVPHY_CH2IDX(ChId)];
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		RxRefClkHz = InstancePtr->HdmiRxRefClkHz;
+	}
+	else {
+		RxRefClkHz = XVphy_GetQuadRefClkFreq(InstancePtr, QuadId,
+								PllPtr->PllRefClkSel);
+	}
+
+	Status |= XVphy_DrpRd(InstancePtr, QuadId, ChId, XVPHY_DRP_RXCLK25,
+                    &DrpVal);
+	DrpVal &= ~(0x00F8);
+	DrpVal |= XVphy_DrpEncodeClk25(RxRefClkHz) << 3;
+	Status |= XVphy_DrpWr(InstancePtr, QuadId, ChId, XVPHY_DRP_RXCLK25,
+                    DrpVal);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured M value to DRP encoding.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return	The DRP encoding for M.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 XVphy_MToDrpEncoding(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId)
+{
+	u8 MRefClkDiv;
+	u8 DrpEncode;
+
+	if ((ChId >= XVPHY_CHANNEL_ID_CH1) && (ChId <= XVPHY_CHANNEL_ID_CH4)) {
+		MRefClkDiv = InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)]
+				.PllParams.MRefClkDiv;
+	}
+	else if ((ChId == XVPHY_CHANNEL_ID_CMN0) ||
+			(ChId == XVPHY_CHANNEL_ID_CMN1)) {
+		MRefClkDiv = InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)]
+				.PllParams.MRefClkDiv;
+	}
+	else {
+		MRefClkDiv = 0;
+	}
+
+	DrpEncode = XVphy_DrpEncodeQpllMCpllMN2(MRefClkDiv);
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured D value to DRP encoding.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	The DRP encoding for D.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 XVphy_DToDrpEncoding(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir)
+{
+	u8 OutDiv;
+	u8 DrpEncode;
+
+	OutDiv = InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+			OutDiv[Dir];
+
+	DrpEncode = XVphy_DrpEncodeCpllTxRxD(OutDiv);
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured N1/N2 value to DRP encoding.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	NId specified to operate on N1 (if == 1) or N2 (if == 2).
+*
+* @return	The DRP encoding for N1/N2.
+*
+* @note		None.
+*
+******************************************************************************/
+static u16 XVphy_NToDrpEncoding(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, u8 NId)
+{
+	u8 NFbDiv;
+	u16 DrpEncode;
+
+	if ((ChId == XVPHY_CHANNEL_ID_CMN0) ||
+			(ChId == XVPHY_CHANNEL_ID_CMN1)) {
+		NFbDiv = InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+				PllParams.NFbDiv;
+		DrpEncode = XVphy_DrpEncodeQpllN(NFbDiv);
+	}
+	else if (NId == 1) {
+		NFbDiv = InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+				PllParams.N1FbDiv;
+		DrpEncode = XVphy_DrpEncodeCpllN1(NFbDiv);
+	}
+	else {
+		NFbDiv = InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+				PllParams.N2FbDiv;
+		DrpEncode = XVphy_DrpEncodeQpllMCpllMN2(NFbDiv);
+	}
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured QPLL's M or CPLL's M or N2
+* values to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the QPLL's M or CPLL's M or N2 values.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 XVphy_DrpEncodeQpllMCpllMN2(u8 AttrEncode)
+{
+	u8 DrpEncode;
+
+	switch (AttrEncode) {
+	case 1:
+		DrpEncode = 16;
+		break;
+	case 6:
+		DrpEncode = 5;
+		break;
+	case 10:
+		DrpEncode = 7;
+		break;
+	case 12:
+		DrpEncode = 13;
+		break;
+	case 20:
+		DrpEncode = 15;
+		break;
+	case 2:
+	case 3:
+	case 4:
+	case 5:
+	case 8:
+	case 16:
+		DrpEncode = (AttrEncode - 2);
+		break;
+	default:
+		DrpEncode = 0xF;
+		break;
+	}
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured CPLL's N1 value to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the CPLL's N1 value.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 XVphy_DrpEncodeCpllN1(u8 AttrEncode)
+{
+	u8 DrpEncode;
+
+	DrpEncode = (AttrEncode - 4) & 0x1;
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured CPLL's D values to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the CPLL's D value.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 XVphy_DrpEncodeCpllTxRxD(u8 AttrEncode)
+{
+	u8 DrpEncode;
+
+	switch (AttrEncode) {
+	case 1:
+		DrpEncode = 0;
+		break;
+	case 2:
+		DrpEncode = 1;
+		break;
+	case 4:
+		DrpEncode = 2;
+		break;
+	case 8:
+		DrpEncode = 3;
+		break;
+	case 16:
+		DrpEncode = 4;
+		break;
+	default:
+		DrpEncode = 0x4;
+		break;
+	}
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured QPLL's N value to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the QPLL's N value.
+*
+* @note		None.
+*
+******************************************************************************/
+static u16 XVphy_DrpEncodeQpllN(u8 AttrEncode)
+{
+	u16 DrpEncode;
+
+	if ((16 <= AttrEncode) && (AttrEncode <= 160)) {
+		DrpEncode = AttrEncode - 2;
+	}
+	else {
+		DrpEncode = 0xFF;
+	}
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured RXDATAWIDTH to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the RXDATAWIDTH value.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 Xvphy_DrpEncodeDataWidth(u8 AttrEncode)
+{
+	u8 DrpEncode;
+
+	switch (AttrEncode) {
+	case 16:
+		DrpEncode = 2;
+		break;
+	case 20:
+		DrpEncode = 3;
+		break;
+	case 32:
+		DrpEncode = 4;
+		break;
+	case 40:
+		DrpEncode = 5;
+		break;
+	case 64:
+		DrpEncode = 6;
+		break;
+	case 80:
+		DrpEncode = 7;
+		break;
+	case 128:
+		DrpEncode = 8;
+		break;
+	case 160:
+		DrpEncode = 9;
+		break;
+	default:
+		DrpEncode = 0xF;
+		break;
+	}
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured RXINTDATAWIDTH to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the RXINTDATAWIDTH value.
+*
+* @note		None.
+*
+******************************************************************************/
+static u8 Xvphy_DrpEncodeIntDataWidth(u8 AttrEncode)
+{
+	u8 DrpEncode;
+
+	switch (AttrEncode) {
+	case 2:
+		DrpEncode = 0;
+		break;
+	case 4:
+		DrpEncode = 1;
+		break;
+	default:
+		DrpEncode = 2;
+		break;
+	}
+
+	return DrpEncode;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate the configured CLK25 to DRP encoding.
+*
+* @param	AttrEncode is the attribute to encode.
+*
+* @return	The DRP encoding for the CLK25 value.
+*
+* @note		None.
+*
+******************************************************************************/
+static u16 XVphy_DrpEncodeClk25(u32 RefClkFreqHz)
+{
+	u16 DrpEncode;
+	u32 RefClkFreqMHz = RefClkFreqHz / 1000000;
+
+	DrpEncode = ((RefClkFreqMHz / 25) +
+			(((RefClkFreqMHz % 25) > 0) ? 1 : 0)) - 1;
+
+	return (DrpEncode & 0x1F);
+}
+
+/*****************************************************************************/
+/**
+* This function configures the CPLL Calibration period and the count tolerance
+* registers.
+*
+* CpllCalPeriod    = ((fPLLClkin * N1 * N2) / (20 * M)) /
+* 						(16000 / (4 * fFreeRunClk))
+* CpllCalTolerance = CpllCalPeriod * 0.10
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param    FreeRunClkFreq is the freerunning clock freq in Hz
+*            driving the GT Wiz instance
+*
+* @return   XST_SUCCESS / XST_FAILURE
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_CfgCpllCalPeriodandTol(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir, u32 FreeRunClkFreq)
+{
+	u64 CpllCalPeriod;
+	u64 CpllCalTolerance;
+	u64 PllVcoFreqHz;
+	u32 RegVal;
+
+	/* Check if ChID is not a GT Channel */
+	if (!XVPHY_ISCH(ChId)) {
+		return XST_FAILURE;
+	}
+
+	PllVcoFreqHz = XVphy_GetPllVcoFreqHz(InstancePtr, QuadId, ChId, Dir);
+	CpllCalPeriod = PllVcoFreqHz * 200 / (u64)FreeRunClkFreq;
+	if (CpllCalPeriod % 10) {
+		CpllCalTolerance = (CpllCalPeriod / 10) + 1;
+	}
+	else {
+		CpllCalTolerance = CpllCalPeriod / 10;
+	}
+
+	/* Read CPLL Calibration Period Value */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+				XVPHY_CPLL_CAL_PERIOD_REG) & ~XVPHY_CPLL_CAL_PERIOD_MASK;
+    RegVal |= CpllCalPeriod & XVPHY_CPLL_CAL_PERIOD_MASK;
+	/* Write new CPLL Calibration Period Value */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+					XVPHY_CPLL_CAL_PERIOD_REG, RegVal);
+
+	/* Read CPLL Calibration Tolerance Value */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+				XVPHY_CPLL_CAL_TOL_REG) & ~XVPHY_CPLL_CAL_TOL_MASK;
+    RegVal |= CpllCalTolerance & XVPHY_CPLL_CAL_TOL_MASK;
+	/* Write new CPLL Calibration Tolerance Value */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+                    XVPHY_CPLL_CAL_TOL_REG, RegVal);
+
+	return XST_SUCCESS;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hdmi.c
@@ -0,0 +1,2721 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_hdmi.c
+ *
+ * This file contains video PHY functionality specific to the HDMI protocol.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Added GTPE2 and GTHE4 support.
+ *       MG   03/08/16 Fixed issue in function XVphy_HdmiCfgCalcMmcmParam
+ *                       for single pixel calculation.
+ * 1.2   gm            Added XVphy_HdmiMmcmStart and
+ *                       XVphy_HdmiMmcmWriteParameters functions
+ *                     Replaced xil_printf with log events
+ *                     Modified XVphy_DruGetRefClkFreqHz
+ *                     Suppressed warning messages due to unused arguments
+ * 1.3   gm   01/11/16 Added error message in XVphy_HdmiCpllParam when DRU is
+ *                     enabled and RX TMDS ratio is 1/40
+ *                     Fixed rounding of DRU refclk frequency
+ *                     Fixed a bug in XVphy_SetHdmiRxParam to update the ChId
+ *                        when DRU is enabled
+ * 1.4   gm   29/11/16 Added preprocessor directives for sw footprint reduction
+ *                     Added TX datawidth dynamic reconfiguration
+ *                     Incorporated AXIlite Freq auto extraction
+ *                     Added extra routine for 2/4 byte tranceiver modes
+ *                     Added logging and register access for ERR_IRQ impl
+ *                     Removed XVphy_HdmiMmcmStart API
+ *                     Fixed c++ compiler warnings
+ * 1.5   gm   27/04/17 Added Div in HdmiCfgCalcMmcmParam search algorithm
+ * 1.6   gm   06/08/17 Added XVPHY_LOG_EVT_HDMI20_ERR error condition in
+ *                       HdmiCfgCalcMmcmParam for GTPE2
+ *                     Removed XVPHY_LOG_EVT_VDCLK_HIGH_ERR error from
+ *                       HdmiCfgCalcMmcmParam since it falls under HDMI20_ERR
+ *                     Added interrupt initialization for TX and RX MMCM lock
+ *                     Removed printing QPLL0 in debug info for GTXE2
+ *                     Set different target DRU line rates for QPLL and
+ *                       CPLL for GTXE2
+ *                     Implemented TX and RX Only uses-cases in
+ *						 XVphy_HdmiDebugInfo API
+ *					   Fixed bug in HdmiCfgCalcMmcmParam when linerate exceeds
+ *					     3.4 Gbps when oversampling is enabled
+ *                     Changed xil_printf new lines to \r\n
+ *                     Marked XVphy_HdmiInitialize deprecated and replaced by
+ *                        XVphy_Hdmi_CfgInitialize
+ *                     Added XVPHY_LOG_EVT_DRU_CLK_ERR error condition to
+ *                        report when DRU REFCLK is out-of-range
+ * 1.7   gm   13/09/17 Added GTYE4 support.
+ *                     Added userclk freq checking in XVphy_HdmiCpllParam &
+ *                        XVphy_HdmiQpllParam API
+ *                     Removed XVphy_DruSetGain API
+ * 1.8   gm   05/14/18 Fixed a bug in XVphy_HdmiQpllParam where linerate is
+ *                        obtained from CH1 instead of QPLL0/1
+ * 1.9   gm   14/05/18 Added TX and RX MMCM lock event logging
+ *                     Removed deprecated XVphy_HdmiInitialize API
+ *
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#if defined (XPAR_XV_HDMITX_0_DEVICE_ID) || defined (XPAR_XV_HDMIRX_0_DEVICE_ID)
+#include "xstatus.h"
+#include "xvphy.h"
+#include "xvphy_i.h"
+#include "xvphy_hdmi.h"
+
+/****************************** Type Definitions ******************************/
+
+typedef struct {
+	u64 DruLineRate;
+	u16 PllScale;
+	u32 Qpll0RefClkMin;
+	u32 Qpll1RefClkMin;
+	u32 CpllRefClkMin;
+	u16 TxMmcmScale;
+	u32 TxMmcmFvcoMin;
+	u32 TxMmcmFvcoMax;
+	u16 RxMmcmScale;
+	u32 RxMmcmFvcoMin;
+	u32 RxMmcmFvcoMax;
+} XVphy_GtHdmiChars;
+
+/**************************** Function Prototypes *****************************/
+
+extern void XVphy_Ch2Ids(XVphy *InstancePtr, XVphy_ChannelId ChId,
+		u8 *Id0, u8 *Id1);
+static const XVphy_GtHdmiChars *GetGtHdmiPtr(XVphy *InstancePtr);
+static void XVphy_HdmiSetSystemClockSelection(XVphy *InstancePtr, u8 QuadId);
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function initializes the Video PHY for HDMI.
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ * @param	CfgPtr is a pointer to the configuration structure that will
+ *		        be used to copy the settings from.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+u32 XVphy_Hdmi_CfgInitialize(XVphy *InstancePtr, u8 QuadId,
+        XVphy_Config *CfgPtr)
+{
+	u8 Id, Id0, Id1;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+
+	/* Init done. */
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_INIT, 0);
+
+	/* Setup the instance. */
+	XVphy_CfgInitialize(InstancePtr, CfgPtr, CfgPtr->BaseAddr);
+
+	/* Set default. */
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].TxState =
+			XVPHY_GT_STATE_IDLE;
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].RxState =
+			XVPHY_GT_STATE_IDLE;
+		/* Initialize Transceiver Width values */
+		if (InstancePtr->Config.TransceiverWidth == 2) {
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				TxDataWidth = 20;
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				TxIntDataWidth = 2;
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				RxDataWidth = 20;
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				RxIntDataWidth = 2;
+		}
+		else {
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				TxDataWidth = 40;
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				TxIntDataWidth = 4;
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				RxDataWidth = 40;
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				RxIntDataWidth = 4;
+		}
+	}
+
+	/* Interrupt Disable. */
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_QPLL0_LOCK);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT);
+	XVphy_IntrDisable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+
+	/* Setup HDMI interrupt handler callback*/
+	XVphy_HdmiIntrHandlerCallbackInit(InstancePtr);
+
+	/* Configure clock detector. */
+	XVphy_ClkDetEnable(InstancePtr, FALSE);
+	XVphy_ClkDetSetFreqTimeout(InstancePtr,
+                InstancePtr->Config.AxiLiteClkFreq);
+	XVphy_ClkDetSetFreqLockThreshold(InstancePtr, 40);
+
+	/* Start capturing logs. */
+	XVphy_LogReset(InstancePtr);
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_INIT, 0);
+
+	XVphy_HdmiSetSystemClockSelection(InstancePtr, QuadId);
+
+	/* Indicate of QPLL is present in design */
+	if ((XVphy_IsTxUsingQpll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CH1) &&
+			(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX))) ||
+		(XVphy_IsRxUsingQpll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CH1) &&
+			(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)))) {
+		InstancePtr->HdmiIsQpllPresent = TRUE;
+	} else {
+		InstancePtr->HdmiIsQpllPresent = FALSE;
+	}
+
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE3) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE4) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTYE4)) {
+		XVphy_SetBufgGtDiv(InstancePtr, XVPHY_DIR_TX, 1);
+		XVphy_SetBufgGtDiv(InstancePtr, XVPHY_DIR_RX, 1);
+	}
+	XVphy_ResetGtPll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_RX, TRUE);
+	XVphy_ResetGtPll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_TX, TRUE);
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2)) {
+		XVphy_ResetGtTxRx(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_RX, TRUE);
+		XVphy_ResetGtTxRx(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, TRUE);
+	}
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_PowerDownGtPll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMNA,
+				TRUE);
+		XVphy_PowerDownGtPll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+				TRUE);
+	}
+	XVphy_MmcmReset(InstancePtr, QuadId, XVPHY_DIR_TX, TRUE);
+	XVphy_MmcmReset(InstancePtr, QuadId, XVPHY_DIR_RX, TRUE);
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+		XVphy_IBufDsEnable(InstancePtr, QuadId, XVPHY_DIR_TX, (FALSE));
+	}
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		XVphy_IBufDsEnable(InstancePtr, QuadId, XVPHY_DIR_RX, (FALSE));
+	}
+
+	/* DRU Settings. */
+	if (InstancePtr->Config.DruIsPresent) {
+		XVphy_IBufDsEnable(InstancePtr, QuadId, XVPHY_DIR_RX, TRUE);
+		XVphy_DruReset(InstancePtr, XVPHY_CHANNEL_ID_CHA, TRUE);
+		XVphy_DruEnable(InstancePtr, XVPHY_CHANNEL_ID_CHA, FALSE);
+	}
+
+	XVphy_SetRxLpm(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA, XVPHY_DIR_RX,
+			1);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3 || \
+	 XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4 || \
+     XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+		XVphy_SetTxVoltageSwing(InstancePtr, QuadId, (XVphy_ChannelId)Id, 0xC);
+#else
+		XVphy_SetTxVoltageSwing(InstancePtr, QuadId, (XVphy_ChannelId)Id, 0x1);
+#endif
+		XVphy_SetTxPreEmphasis(InstancePtr, QuadId, (XVphy_ChannelId)Id, 0x1);
+	}
+
+	/* Clear Interrupt Register */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_STS_REG,
+			0xFFFFFFFF);
+
+	/* Interrupt Enable. */
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_QPLL0_LOCK);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT);
+	XVphy_IntrEnable(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE);
+	XVphy_ClkDetEnable(InstancePtr, TRUE);
+
+	/* Set the flag to indicate the driver is. */
+	InstancePtr->IsReady = XIL_COMPONENT_IS_READY;
+
+	/* Init done. */
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_INIT, 1);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function Sets the System Clock Selection
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void XVphy_HdmiSetSystemClockSelection(XVphy *InstancePtr, u8 QuadId)
+{
+	XVphy_PllType XVphy_QPllType;
+
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) {
+			XVphy_QPllType = XVPHY_PLL_TYPE_QPLL;
+		}
+		else {
+			XVphy_QPllType = XVPHY_PLL_TYPE_QPLL0;
+		}
+
+		/* Set system clock selections */
+		if (InstancePtr->Config.TxSysPllClkSel ==
+				InstancePtr->Config.RxSysPllClkSel) {
+			if (InstancePtr->Config.RxSysPllClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_CPLL_OUTCLK) {
+				XVphy_PllInitialize(InstancePtr, QuadId,
+						XVPHY_CHANNEL_ID_CHA,
+						InstancePtr->Config.RxRefClkSel,
+						InstancePtr->Config.RxRefClkSel,
+						XVPHY_PLL_TYPE_CPLL,
+						XVPHY_PLL_TYPE_CPLL);
+			}
+			else {
+				XVphy_PllInitialize(InstancePtr, QuadId,
+						XVPHY_CHANNEL_ID_CMN0,
+						InstancePtr->Config.RxRefClkSel,
+						InstancePtr->Config.RxRefClkSel,
+						XVphy_QPllType,
+						XVphy_QPllType);
+			}
+		}
+		else if (InstancePtr->Config.TxSysPllClkSel ==
+				XVPHY_SYSCLKSELDATA_TYPE_CPLL_OUTCLK) {
+			XVphy_PllInitialize(InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CHA,
+					InstancePtr->Config.RxRefClkSel,
+					InstancePtr->Config.TxRefClkSel,
+					XVPHY_PLL_TYPE_CPLL,
+					XVphy_QPllType);
+		}
+		else {
+			XVphy_PllInitialize(InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CMN0,
+					InstancePtr->Config.TxRefClkSel,
+					InstancePtr->Config.RxRefClkSel,
+					XVphy_QPllType,
+					XVPHY_PLL_TYPE_CPLL);
+		}
+	}
+	/* GTPE2 */
+	else {
+		if (InstancePtr->Config.TxSysPllClkSel ==
+				XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK) {
+		XVphy_PllInitialize(InstancePtr, QuadId,
+			XVPHY_CHANNEL_ID_CMN0,
+			InstancePtr->Config.TxRefClkSel,
+			InstancePtr->Config.RxRefClkSel,
+			XVPHY_PLL_TYPE_PLL0,
+			XVPHY_PLL_TYPE_PLL1);
+		}
+		else {
+		XVphy_PllInitialize(InstancePtr, QuadId,
+				XVPHY_CHANNEL_ID_CMN0,
+				InstancePtr->Config.RxRefClkSel,
+				InstancePtr->Config.TxRefClkSel,
+				XVPHY_PLL_TYPE_PLL1,
+				XVPHY_PLL_TYPE_PLL0);
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function Updates the VPHY clocking.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	TxSysPllClkSel is the SYSCLKDATA selection for TX.
+* @param	RxSysPllClkSel is the SYSCLKDATA selection for RX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiUpdateClockSelection(XVphy *InstancePtr, u8 QuadId,
+		XVphy_SysClkDataSelType TxSysPllClkSel,
+		XVphy_SysClkDataSelType RxSysPllClkSel)
+{
+	u8 Id, Id0, Id1;
+
+	/* Reset PLL */
+	XVphy_ResetGtPll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_RX, TRUE);
+	XVphy_ResetGtPll(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_TX, TRUE);
+
+	/* Set default. */
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].TxState =
+			XVPHY_GT_STATE_IDLE;
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].RxState =
+			XVPHY_GT_STATE_IDLE;
+	}
+
+	/* Update VPhy Clocking */
+	InstancePtr->Config.TxSysPllClkSel = TxSysPllClkSel;
+	InstancePtr->Config.RxSysPllClkSel = RxSysPllClkSel;
+	XVphy_HdmiSetSystemClockSelection(InstancePtr, QuadId);
+}
+
+/*****************************************************************************/
+/**
+* This function resets the GT TX alignment module.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Reset specifies TRUE/FALSE value to either assert or deassert
+*		reset on the TX alignment module, respectively.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_TxAlignReset(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Reset)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read TX align register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_TX_BUFFER_BYPASS_REG);
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XVPHY_TX_BUFFER_BYPASS_TXPHDLYRESET_MASK(Id);
+	}
+
+	/* Write new value to BUFG_GT register. */
+	if (Reset) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_TX_BUFFER_BYPASS_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function resets the GT TX alignment module.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Start specifies TRUE/FALSE value to either start or ttop the TX
+*		alignment module, respectively.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_TxAlignStart(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Start)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read TX align register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_TX_BUFFER_BYPASS_REG);
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XVPHY_TX_BUFFER_BYPASS_TXPHALIGN_MASK(Id);
+	}
+
+	/* Write new value to BUFG_GT register. */
+	if (Start) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_TX_BUFFER_BYPASS_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function enables the VPHY's detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the clock detector respectively.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetEnable(XVphy *InstancePtr, u8 Enable)
+{
+	u32 RegVal;
+
+	/* Read clkdet ctrl register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_CLKDET_CTRL_REG);
+
+	/* Write new value to clkdet ctrl register. */
+	if (Enable) {
+		RegVal |= XVPHY_CLKDET_CTRL_RUN_MASK;
+	}
+	else {
+		RegVal &= ~XVPHY_CLKDET_CTRL_RUN_MASK;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function clears the clock detector TX/RX timer.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetTimerClear(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	/* Read the clock detector control register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_CLKDET_CTRL_REG);
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegVal |= XVPHY_CLKDET_CTRL_TX_TMR_CLR_MASK;
+	}
+	else {
+		RegVal |= XVPHY_CLKDET_CTRL_RX_TMR_CLR_MASK;
+	}
+
+	/* Write new value to clkdet ctrl register. */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function resets clock detector TX/RX frequency.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetFreqReset(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	/* Read clkdet ctrl register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_CLKDET_CTRL_REG);
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegVal |= XVPHY_CLKDET_CTRL_TX_FREQ_RST_MASK;
+	}
+	else {
+		RegVal |= XVPHY_CLKDET_CTRL_RX_FREQ_RST_MASK;
+	}
+
+	/* Write new value to clkdet ctrl register. */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the clock detector frequency lock counter threshold value.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ThresholdVal is the threshold value to be set.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetSetFreqLockThreshold(XVphy *InstancePtr, u16 ThresholdVal)
+{
+	u32 RegVal;
+
+	/* Read clkdet ctrl register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_CLKDET_CTRL_REG);
+	RegVal &= ~XVPHY_CLKDET_CTRL_RX_FREQ_RST_MASK;
+
+	/* Update with new threshold. */
+	RegVal |= (ThresholdVal << XVPHY_CLKDET_CTRL_FREQ_LOCK_THRESH_SHIFT);
+
+	/* Write new value to clkdet ctrl register. */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_CLKDET_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function checks clock detector RX/TX frequency zero indicator bit.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	- TRUE if zero frequency.
+*		- FALSE otherwise, if non-zero frequency.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XVphy_ClkDetCheckFreqZero(XVphy *InstancePtr, XVphy_DirectionType Dir)
+{
+	u32 MaskVal = 0;
+	u32 RegVal;
+
+	if (Dir == XVPHY_DIR_TX) {
+		MaskVal = XVPHY_CLKDET_STAT_TX_FREQ_ZERO_MASK;
+	}
+	else {
+		MaskVal = XVPHY_CLKDET_STAT_RX_FREQ_ZERO_MASK;
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_DRU_STAT_REG);
+	RegVal &= MaskVal;
+
+	if (RegVal) {
+		return (TRUE);
+	}
+
+	return (FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function sets clock detector frequency lock counter threshold value.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	TimeoutVal is the timeout value and is normally the system clock
+*		frequency.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetSetFreqTimeout(XVphy *InstancePtr, u32 TimeoutVal)
+{
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+			XVPHY_CLKDET_FREQ_TMR_TO_REG, TimeoutVal);
+}
+
+/*****************************************************************************/
+/**
+* This function loads the timer to TX/RX in the clock detector.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+* @param	TimeoutVal is the timeout value to store in the clock detector.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetTimerLoad(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, u32 TimeoutVal)
+{
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_CLKDET_TMR_TX_REG;
+	}
+	else {
+		RegOffset = XVPHY_CLKDET_TMR_RX_REG;
+	}
+
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, TimeoutVal);
+}
+
+/*****************************************************************************/
+/**
+* This function returns the frequency of the RX/TX reference clock as
+* measured by the clock detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	The measured frequency of the RX/TX reference clock.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ClkDetGetRefClkFreqHz(XVphy *InstancePtr, XVphy_DirectionType Dir)
+{
+	u32 RegOffset;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_CLKDET_FREQ_TX_REG;
+	}
+	else {
+		RegOffset = XVPHY_CLKDET_FREQ_RX_REG;
+	}
+
+	return XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+}
+
+/*****************************************************************************/
+/**
+* This function returns the frequency of the DRU reference clock as measured by
+* the clock detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	The measured frequency of the DRU reference clock.
+*
+* @note		The design must have a DRU for this function to return a valid
+*		value.
+*
+******************************************************************************/
+u32 XVphy_DruGetRefClkFreqHz(XVphy *InstancePtr)
+{
+	u32 DruFreqHz = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_CLKDET_FREQ_DRU_REG);
+
+
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) {
+		if (DruFreqHz > XVPHY_HDMI_GTXE2_DRU_REFCLK_MIN &&
+				DruFreqHz < XVPHY_HDMI_GTXE2_DRU_REFCLK_MAX){
+			return XVPHY_HDMI_GTXE2_DRU_REFCLK;
+		}
+	}
+	else if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE2) {
+		if (DruFreqHz > XVPHY_HDMI_GTHE2_DRU_REFCLK_MIN &&
+				DruFreqHz < XVPHY_HDMI_GTHE2_DRU_REFCLK_MAX){
+			return XVPHY_HDMI_GTHE2_DRU_REFCLK;
+		}
+	}
+	else if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+		if (DruFreqHz > XVPHY_HDMI_GTPE2_DRU_REFCLK_MIN &&
+				DruFreqHz < XVPHY_HDMI_GTPE2_DRU_REFCLK_MAX){
+			return XVPHY_HDMI_GTPE2_DRU_REFCLK;
+		}
+	}
+	else if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE3) {
+		if (DruFreqHz > XVPHY_HDMI_GTHE3_DRU_REFCLK_MIN &&
+				DruFreqHz < XVPHY_HDMI_GTHE3_DRU_REFCLK_MAX){
+			return XVPHY_HDMI_GTHE3_DRU_REFCLK;
+		}
+	}
+	else if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE4) {
+		if (DruFreqHz > XVPHY_HDMI_GTHE4_DRU_REFCLK_MIN &&
+				DruFreqHz < XVPHY_HDMI_GTHE4_DRU_REFCLK_MAX){
+			return XVPHY_HDMI_GTHE4_DRU_REFCLK;
+		}
+	}
+	else {
+		if (DruFreqHz > XVPHY_HDMI_GTYE4_DRU_REFCLK_MIN &&
+				DruFreqHz < XVPHY_HDMI_GTYE4_DRU_REFCLK_MAX){
+			return XVPHY_HDMI_GTYE4_DRU_REFCLK;
+		}
+	}
+	/* Return Failure */
+	return XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+* This function resets the DRU in the VPHY.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Reset specifies TRUE/FALSE value to either enable or disable
+*		the DRU respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_DruReset(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Reset)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read DRU ctrl register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_DRU_CTRL_REG);
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XVPHY_DRU_CTRL_RST_MASK(Id);
+	}
+
+	/* Write DRU ctrl register. */
+	if (Reset) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_DRU_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function enabled/disables the DRU in the VPHY.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ChId is the channel ID to operate on.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable
+*		the DRU, respectively.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_DruEnable(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Enable)
+{
+	u32 RegVal;
+	u32 MaskVal = 0;
+	u8 Id, Id0, Id1;
+
+	/* Read DRU ctrl register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_DRU_CTRL_REG);
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		MaskVal |= XVPHY_DRU_CTRL_EN_MASK(Id);
+	}
+
+	/* Write DRU ctrl register. */
+	if (Enable) {
+		RegVal |= MaskVal;
+	}
+	else {
+		RegVal &= ~MaskVal;
+	}
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_DRU_CTRL_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function gets the DRU version
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	None.
+*
+******************************************************************************/
+u16 XVphy_DruGetVersion(XVphy *InstancePtr)
+{
+	u32 RegVal;
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_DRU_STAT_REG);
+	RegVal &= XVPHY_DRU_STAT_VERSION_MASK;
+	RegVal >>= XVPHY_DRU_STAT_VERSION_SHIFT;
+
+	return ((u16)RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the DRU center frequency.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ChId specifies the channel ID.
+* @param	CenterFreqHz is the frequency value to set.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_DruSetCenterFreqHz(XVphy *InstancePtr, XVphy_ChannelId ChId,
+		u64 CenterFreqHz)
+{
+	u32 CenterFreqL;
+	u32 CenterFreqH;
+	u32 RegOffset;
+	u8 Id, Id0, Id1;
+
+	/* Split the 64-bit input into 2 32-bit values. */
+	CenterFreqL = (u32)CenterFreqHz;
+	CenterFreqHz >>= 32;
+	CenterFreqHz &= XVPHY_DRU_CFREQ_H_MASK;;
+	CenterFreqH = (u32)CenterFreqHz;
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		RegOffset = XVPHY_DRU_CFREQ_L_REG(Id);
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset,
+				CenterFreqL);
+
+		RegOffset = XVPHY_DRU_CFREQ_H_REG(Id);
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset,
+				CenterFreqH);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the center frequency value for the DRU.
+*
+* @param	InstancePtr is a pointer to the XVphy GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return	The calculated DRU Center frequency value.
+*
+* @note		According to XAPP1240:
+*			Center_f = fDIN * (2^32)/fdruclk
+*		The DRU clock is derived from the measured reference clock and
+*		the current QPLL settings.
+*
+******************************************************************************/
+u64 XVphy_DruCalcCenterFreqHz(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId)
+{
+	XVphy_Channel *ChPtr, *CmnPtr;
+	u64 DruRefClk;
+	u64 ClkDetRefClk;
+	u64 DataRate;
+	u64 FDin;
+	u64 FDruClk;
+
+	DruRefClk = XVphy_DruGetRefClkFreqHz(InstancePtr);
+	ClkDetRefClk = XVphy_ClkDetGetRefClkFreqHz(InstancePtr, XVPHY_DIR_RX);
+
+	/* Take the master channel (channel 1). */
+	ChPtr = &InstancePtr->Quads[QuadId].Ch1;
+
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+		CmnPtr = &InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)];
+		FDruClk = (DruRefClk * CmnPtr->PllParams.N1FbDiv *
+			CmnPtr->PllParams.N2FbDiv * 2) /
+			(CmnPtr->PllParams.MRefClkDiv * ChPtr->RxOutDiv * 20);
+	}
+	else if ((ChId == XVPHY_CHANNEL_ID_CMN0) ||
+			(ChId == XVPHY_CHANNEL_ID_CMN1)) {
+		FDruClk = (DruRefClk * InstancePtr->Quads[QuadId].Plls[
+			XVPHY_CH2IDX(ChId)].PllParams.NFbDiv) /
+			(ChPtr->RxOutDiv * 20);
+	}
+	else {
+		FDruClk = (DruRefClk * ChPtr->PllParams.N1FbDiv *
+			ChPtr->PllParams.N2FbDiv * 2) /
+			(ChPtr->PllParams.MRefClkDiv * ChPtr->RxOutDiv * 20);
+	}
+
+	DataRate = 10 * ClkDetRefClk;
+	FDin = DataRate * ((u64)1 << 32);
+
+	/* Check for divide by zero. */
+	if (FDin && FDruClk) {
+		return (FDin / FDruClk);
+	}
+	return 0;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the GT RX CDR and Equalization for DRU mode.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Enable enables the DRU logic (when 1), or disables (when 0).
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_HdmiGtDruModeEnable(XVphy *InstancePtr, u8 Enable)
+{
+	u32 RegVal;
+	u32 RegMask = 0;
+	u8 Id, Id0, Id1;
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_DRU_EN, Enable);
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_RX_EQ_CDR_REG);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		RegMask |= XVPHY_RX_STATUS_RXCDRHOLD_MASK(Id) |
+			XVPHY_RX_STATUS_RXOSOVRDEN_MASK(Id) |
+			XVPHY_RX_STATUS_RXLPMLFKLOVRDEN_MASK(Id) |
+			XVPHY_RX_STATUS_RXLPMHFOVRDEN_MASK(Id);
+	}
+
+	if (Enable) {
+		RegVal |= RegMask;
+	}
+	else {
+		RegVal &= ~RegMask;
+	}
+
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_RX_EQ_CDR_REG,
+			RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the HDMI MMCM parameters.
+*
+* @param	InstancePtr is a pointer to the Vphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+* @param	Ppc specifies the total number of pixels per clock.
+*		- 1 = XVIDC_PPC_1
+*		- 2 = XVIDC_PPC_2
+*		- 4 = XVIDC_PPC_4
+* @param	Bpc specifies the color depth/bits per color component.
+*		- 6 = XVIDC_BPC_6
+*		- 8 = XVIDC_BPC_8
+*		- 10 = XVIDC_BPC_10
+*		- 12 = XVIDC_BPC_12
+*		- 16 = XVIDC_BPC_16
+*
+* @return
+*		- XST_SUCCESS if calculated PLL parameters updated successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_HdmiCfgCalcMmcmParam(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir,
+		XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc)
+{
+	u32 RefClk;
+	u8 Div;
+	u8 Mult;
+	u8 MultDiv;
+	u8 Valid;
+	u64 LineRate = 0;
+	XVphy_Mmcm *MmcmPtr;
+	XVphy_PllType PllType;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	/* Get line rate. */
+	PllType = XVphy_GetPllType(InstancePtr, 0, Dir,
+			XVPHY_CHANNEL_ID_CH1);
+
+	switch (PllType) {
+		case XVPHY_PLL_TYPE_QPLL:
+		case XVPHY_PLL_TYPE_QPLL0:
+		case XVPHY_PLL_TYPE_PLL0:
+			LineRate = InstancePtr->Quads[QuadId].Cmn0.LineRateHz;
+			break;
+		case XVPHY_PLL_TYPE_QPLL1:
+		case XVPHY_PLL_TYPE_PLL1:
+			LineRate = InstancePtr->Quads[QuadId].Cmn1.LineRateHz;
+			break;
+		default:
+			LineRate = InstancePtr->Quads[QuadId].Ch1.LineRateHz;
+			break;
+	}
+
+	if (((LineRate / 1000000) > 2970) && (Ppc == XVIDC_PPC_1)) {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_1PPC_ERR, 1);
+		XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_MMCM_CFG, 1);
+		XVphy_ErrorHandler(InstancePtr);
+		return (XST_FAILURE);
+	}
+	else if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) &&
+			 ((LineRate / 1000000) > 2970)) {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_HDMI20_ERR, 1);
+		XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_VD_NOT_SPRTD, 1);
+		XVphy_ErrorHandler(InstancePtr);
+		return (XST_FAILURE);
+	}
+
+	Div = 1;
+
+	do {
+		if (Dir == XVPHY_DIR_RX) {
+			RefClk = InstancePtr->HdmiRxRefClkHz;
+			MmcmPtr= &InstancePtr->Quads[QuadId].RxMmcm;
+
+			RefClk = RefClk / (GetGtHdmiPtr(InstancePtr))->RxMmcmScale;
+			Mult = (GetGtHdmiPtr(InstancePtr))->RxMmcmFvcoMax * Div / RefClk;
+		}
+		else {
+			RefClk = InstancePtr->HdmiTxRefClkHz;
+			MmcmPtr= &InstancePtr->Quads[QuadId].TxMmcm;
+
+			RefClk = RefClk / (GetGtHdmiPtr(InstancePtr))->TxMmcmScale;
+			Mult = (GetGtHdmiPtr(InstancePtr))->TxMmcmFvcoMax * Div / RefClk;
+		}
+
+		/* Return if RefClk is below valid range */
+		if (RefClk < 20000000) {
+			return (XST_FAILURE);
+		}
+
+		/* In case of 4 pixels per clock, the M must be a multiple of four. */
+		if (Ppc == XVIDC_PPC_4) {
+			Mult = Mult / 4;
+			Mult = Mult * 4;
+		}
+		/* Else the M must be a multiple of two. */
+		else if (Ppc == XVIDC_PPC_2) {
+			Mult = Mult / 2;
+			Mult = Mult * 2;
+		}
+
+
+		Valid = (FALSE);
+		do {
+            MultDiv = Mult / Div;
+			MmcmPtr->ClkFbOutMult = Mult;
+			MmcmPtr->DivClkDivide = Div;
+
+			if (InstancePtr->Config.TransceiverWidth == 4) {
+				/* Link clock: TMDS clock ratio 1/40. */
+				if ((LineRate / 1000000) >= 3400) {
+					if ((Dir == XVPHY_DIR_TX) &&
+							(((LineRate / 1000000) / InstancePtr->
+									HdmiTxSampleRate) < 3400)) {
+						MmcmPtr->ClkOut0Div = MultDiv * 4;
+					}
+					else {
+						MmcmPtr->ClkOut0Div = MultDiv;
+					}
+				}
+				/* Link clock: TMDS clock ratio 1/10. */
+				else {
+					MmcmPtr->ClkOut0Div = MultDiv * 4;
+				}
+			}
+			else { /* 2 Byte Mode */
+				/* Link clock: TMDS clock ratio 1/40. */
+				if ((LineRate / 1000000) >= 3400) {
+					if ((Dir == XVPHY_DIR_TX) &&
+							(((LineRate / 1000000) / InstancePtr->
+									HdmiTxSampleRate) < 3400)) {
+						MmcmPtr->ClkOut0Div = MultDiv * 2;
+					}
+					else {
+						MmcmPtr->ClkOut0Div = MultDiv / 2;
+					}
+				}
+				/* Link clock: TMDS clock ratio 1/10. */
+				else {
+					MmcmPtr->ClkOut0Div = MultDiv * 2;
+				}
+			}
+
+			/* TMDS Clock */
+			MmcmPtr->ClkOut1Div = MultDiv * ((Dir == XVPHY_DIR_TX) ?
+					(InstancePtr->HdmiTxSampleRate) : 1);
+
+			/* Video clock. */
+			MmcmPtr->ClkOut2Div = 0;
+
+			switch (Bpc) {
+			case XVIDC_BPC_10:
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 5 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					/* The clock ratio is 2.5 */
+					/* The PLL only supports integer values */
+					/* The MultDiv must be dividable by two (2 * 2.5 = 5)
+						to get an integer number */
+					if ((MultDiv % 2) == 0) {
+						MmcmPtr->ClkOut2Div = (MultDiv * 5 / 2 *
+							((Dir == XVPHY_DIR_TX)?
+							(InstancePtr->HdmiTxSampleRate) : 1));
+					}
+				}
+				/* Single pixel. */
+				else {
+					/* The clock ratio is 1.25 */
+					/* The PLL only supports integer values */
+					/* The MultDiv must be dividable by four (4 * 1.25 = 5)
+						to get an integer number */
+					if ((MultDiv % 4) == 0) {
+						MmcmPtr->ClkOut2Div = (MultDiv * 5 / 4 *
+							((Dir == XVPHY_DIR_TX) ?
+							(InstancePtr->HdmiTxSampleRate) : 1));
+					}
+				}
+				break;
+			case XVIDC_BPC_12:
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 6 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 3 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Single pixel. */
+				else {
+					/* The clock ratio is 1.5 */
+					/* The PLL only supports integer values */
+					/* The MultDiv must be dividable by two (2 * 1.5 = 3)
+						to get an integer number */
+					if ((MultDiv % 2) == 0) {
+						MmcmPtr->ClkOut2Div = (MultDiv * 3 / 2 *
+							((Dir == XVPHY_DIR_TX) ?
+							(InstancePtr->HdmiTxSampleRate) : 1));
+					}
+				}
+				break;
+			case XVIDC_BPC_16 :
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 8 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 4 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Single pixel. */
+				else {
+					MmcmPtr->ClkOut2Div = (MultDiv * 2 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				break;
+			case XVIDC_BPC_8:
+			default:
+				/* Quad pixel. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 4 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Dual pixel. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					MmcmPtr->ClkOut2Div = (MultDiv * 2 *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				/* Single pixel. */
+				else {
+					MmcmPtr->ClkOut2Div = (MultDiv *
+						((Dir == XVPHY_DIR_TX) ?
+						(InstancePtr->HdmiTxSampleRate) : 1));
+				}
+				break;
+			}
+
+			/* Only do this when the ClkOut2Div has been set */
+			if (MmcmPtr->ClkOut2Div) {
+				if (Dir == XVPHY_DIR_RX) {
+					/* Correct divider value if TMDS clock ratio is 1/40. */
+					if (InstancePtr->HdmiRxTmdsClockRatio) {
+						if ((MmcmPtr->ClkOut2Div % 4) == 0) {
+							MmcmPtr->ClkOut2Div = MmcmPtr->ClkOut2Div / 4;
+						}
+						/* Not divisible by 4: repeat loop with a lower
+						 * multiply value. */
+						else {
+							MmcmPtr->ClkOut2Div = 255;
+						}
+					}
+				}
+				/* TX. */
+				else if ((((LineRate / 1000000) >= 3400) &&
+							(InstancePtr->HdmiTxSampleRate == 1)) ||
+						 (((LineRate / 1000000) / InstancePtr->
+								HdmiTxSampleRate) >= 3400)) {
+					if ((MmcmPtr->ClkOut2Div % 4) == 0) {
+						MmcmPtr->ClkOut2Div = MmcmPtr->ClkOut2Div / 4;
+					}
+					/* Not divisible by 4: repeat loop with a lower
+					 * multiply value. */
+					else {
+						MmcmPtr->ClkOut2Div = 255;
+					}
+				}
+			}
+
+			/* Check values. */
+			if ((MmcmPtr->ClkOut0Div > 0) && (MmcmPtr->ClkOut0Div <= 128) &&
+				(MmcmPtr->ClkOut1Div > 0) && (MmcmPtr->ClkOut1Div <= 128) &&
+				(MmcmPtr->ClkOut2Div > 0) && (MmcmPtr->ClkOut2Div <= 128)) {
+				Valid = (TRUE);
+			}
+			else {
+				/* 4 pixels per clock. */
+				if (Ppc == (XVIDC_PPC_4)) {
+					/* Decrease Mult value. */
+					Mult -= 4;
+				}
+				/* 2 pixels per clock. */
+				else if (Ppc == (XVIDC_PPC_2)) {
+					/* Decrease M value. */
+					Mult -= 2;
+				}
+				/* 1 pixel per clock */
+				else {
+					/* Decrease M value */
+					Mult -= 1;
+				}
+			}
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4 || \
+     XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+		} while (!Valid && (Mult > 0) && (Mult < 129));
+#else
+		} while (!Valid && (Mult > 0) && (Mult < 65));
+#endif
+
+		/* Increment divider */
+		Div++;
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4 || \
+     XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+	} while (!Valid && (Div > 0) && (Div < 107));
+#else
+	} while (!Valid && (Div > 0) && (Div < 20));
+#endif
+
+	if (Valid) {
+		XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_MMCM_CFG, 0);
+		return (XST_SUCCESS);
+	}
+	else {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_MMCM_ERR, 1);
+		XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_MMCM_CFG, 1);
+		XVphy_ErrorHandler(InstancePtr);
+		return (XST_FAILURE);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the QPLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if calculated QPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_HdmiQpllParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir)
+{
+	u32 Status;
+	u64 RefClk = 0;
+	u32 *RefClkPtr;
+	u64 TxLineRate = 0;
+	u8 Id, Id0, Id1;
+
+	u8 SRArray[] = {1, 3, 5};
+	u8 SRIndex;
+	u8 SRValue;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	XVphy_SysClkDataSelType SysClkDataSel = (XVphy_SysClkDataSelType) 0;
+	XVphy_SysClkOutSelType SysClkOutSel = (XVphy_SysClkOutSelType) 0;
+	XVphy_ChannelId ActiveCmnId = XVPHY_CHANNEL_ID_CMN0;
+
+	u32 QpllRefClk;
+	u32 QpllClkMin = 0;
+
+	/* Determine QPLL reference clock from the first (master) channel. */
+	if (Dir == XVPHY_DIR_RX) {
+		QpllRefClk = InstancePtr->HdmiRxRefClkHz;
+		RefClkPtr = &InstancePtr->HdmiRxRefClkHz;
+	}
+	else {
+		QpllRefClk = InstancePtr->HdmiTxRefClkHz;
+		RefClkPtr = &InstancePtr->HdmiTxRefClkHz;
+	}
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+	/* Determine which QPLL to use. */
+	if (((102343750 <= QpllRefClk) && (QpllRefClk <= 122500000)) ||
+		((204687500 <= QpllRefClk) && (QpllRefClk <= 245000000)) ||
+		((409375000 <= QpllRefClk) && (QpllRefClk <= 490000000))) {
+		SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK;
+		SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL1_REFCLK;
+		ActiveCmnId = XVPHY_CHANNEL_ID_CMN1;
+		QpllClkMin = (u32) XVPHY_HDMI_GTHE3_QPLL1_REFCLK_MIN;
+	}
+	else {
+		SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK;
+		SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL0_REFCLK;
+		ActiveCmnId = XVPHY_CHANNEL_ID_CMN0;
+		QpllClkMin = (u32) XVPHY_HDMI_GTHE3_QPLL0_REFCLK_MIN;
+	}
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+	/* Determine which QPLL to use. */
+	if (((102343750 <= QpllRefClk) && (QpllRefClk <= 122500000)) ||
+		((204687500 <= QpllRefClk) && (QpllRefClk <= 245000000)) ||
+		((409375000 <= QpllRefClk) && (QpllRefClk <= 490000000))) {
+		SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK;
+		SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL1_REFCLK;
+		ActiveCmnId = XVPHY_CHANNEL_ID_CMN1;
+		QpllClkMin = (u32) XVPHY_HDMI_GTHE4_QPLL1_REFCLK_MIN;
+	}
+	else {
+		SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK;
+		SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL0_REFCLK;
+		ActiveCmnId = XVPHY_CHANNEL_ID_CMN0;
+		QpllClkMin = (u32) XVPHY_HDMI_GTHE4_QPLL0_REFCLK_MIN;
+	}
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+	/* Determine which QPLL to use. */
+	if (((102343750 <= QpllRefClk) && (QpllRefClk <= 122500000)) ||
+		((204687500 <= QpllRefClk) && (QpllRefClk <= 245000000)) ||
+		((409375000 <= QpllRefClk) && (QpllRefClk <= 490000000))) {
+		SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK;
+		SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL1_REFCLK;
+		ActiveCmnId = XVPHY_CHANNEL_ID_CMN1;
+		QpllClkMin = (u32) XVPHY_HDMI_GTYE4_QPLL1_REFCLK_MIN;
+	}
+	else {
+		SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK;
+		SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL0_REFCLK;
+		ActiveCmnId = XVPHY_CHANNEL_ID_CMN0;
+		QpllClkMin = (u32) XVPHY_HDMI_GTYE4_QPLL0_REFCLK_MIN;
+	}
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+	SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK;
+	SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL_REFCLK;
+	ActiveCmnId = XVPHY_CHANNEL_ID_CMN;
+	QpllClkMin = (GetGtHdmiPtr(InstancePtr))->Qpll0RefClkMin;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	SysClkDataSel = XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK;
+	SysClkOutSel = XVPHY_SYSCLKSELOUT_TYPE_QPLL_REFCLK;
+	ActiveCmnId = XVPHY_CHANNEL_ID_CMN;
+	QpllClkMin = (GetGtHdmiPtr(InstancePtr))->Qpll0RefClkMin;
+#endif
+
+	/* Update QPLL clock selections. */
+	XVphy_CfgSysClkDataSel(InstancePtr, QuadId, Dir, SysClkDataSel);
+	XVphy_CfgSysClkOutSel(InstancePtr, QuadId, Dir, SysClkOutSel);
+
+	/* RX is using QPLL. */
+	if (Dir == XVPHY_DIR_RX) {
+		/* Check if the reference clock is not below the minimum QPLL
+		 * input frequency. */
+		if (QpllRefClk >= QpllClkMin) {
+			RefClk = QpllRefClk;
+
+			/* Scaled line rate. */
+			if (InstancePtr->HdmiRxTmdsClockRatio) {
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CMNA, (RefClk * 40));
+			}
+			else {
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CMNA, (RefClk * 10));
+			}
+
+			/* Clear DRU is enabled flag. */
+			InstancePtr->HdmiRxDruIsEnabled = 0;
+
+			/* Set RX data width. */
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+					&Id0, &Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				if (InstancePtr->Config.TransceiverWidth == 2) {
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxDataWidth = 20;
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxIntDataWidth = 2;
+				}
+				else {
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxDataWidth = 40;
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxIntDataWidth = 4;
+				}
+			}
+
+		}
+		/* The reference clock is below the minimum frequency thus
+		 * select the DRU. */
+		else if (InstancePtr->Config.DruIsPresent) {
+			RefClk = XVphy_DruGetRefClkFreqHz(InstancePtr);
+            /* Check DRU frequency */
+			if (RefClk == XST_FAILURE) {
+				XVphy_LogWrite(InstancePtr,
+						XVPHY_LOG_EVT_DRU_CLK_ERR, 1);
+				XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_DRU_CLK, 1);
+				XVphy_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+
+			/* Round input frequency to 10 kHz. */
+			RefClk = (RefClk+5000) / 10000;
+			RefClk = RefClk * 10000;
+
+			/* Set the DRU to operate at a linerate of 2.5 Gbps. */
+			XVphy_CfgLineRate(InstancePtr,
+				QuadId, XVPHY_CHANNEL_ID_CMNA,
+#if (XPAR_VPHY_0_TRANSCEIVER != XVPHY_GTXE2)
+				(GetGtHdmiPtr(InstancePtr))->DruLineRate);
+#else
+				XVPHY_HDMI_GTXE2_DRU_LRATE_QPLL);
+#endif
+
+			/* Set DRU is enabled flag. */
+			InstancePtr->HdmiRxDruIsEnabled = 1;
+
+			/* Set RX data width to 40 and 4 bytes. */
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+					&Id0, &Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[QuadId].Plls[
+					XVPHY_CH2IDX(Id)].RxDataWidth = 20;
+				InstancePtr->Quads[QuadId].Plls[
+					XVPHY_CH2IDX(Id)].RxIntDataWidth = 2;
+			}
+		}
+		else {
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_NO_DRU, 1);
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_NO_DRU, 1);
+			XVphy_ErrorHandler(InstancePtr);
+			return (XST_FAILURE);
+		}
+	}
+
+	/* TX is using QPLL. */
+	else {
+		/* Update TX line rates. */
+		XVphy_CfgLineRate(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CMNA,
+				(u64)((*RefClkPtr) * 10));
+		TxLineRate = (*RefClkPtr) / 100000;;
+
+		/* Set default TX sample rate. */
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		/* Check if the linerate is above the 340 Mcsc. */
+		if ((TxLineRate) >= 3400) {
+			(*RefClkPtr) = (*RefClkPtr) / 4;
+		}
+	}
+
+	/* Calculate QPLL values. */
+	for (SRIndex = 0; SRIndex < sizeof(SRArray); SRIndex++) {
+		/* Only use oversampling when then TX is using the QPLL. */
+		if (Dir == XVPHY_DIR_TX) {
+			SRValue = SRArray[SRIndex];
+
+			/* TX reference clock is below the minimum QPLL clock
+			 * input frequency. */
+			if ((*RefClkPtr) < QpllClkMin) {
+				RefClk = ((*RefClkPtr) * SRValue);
+
+				/* Calculate scaled line rate. */
+				if (TxLineRate >= 3400) {
+					XVphy_CfgLineRate(InstancePtr, QuadId,
+						XVPHY_CHANNEL_ID_CMNA,
+						(u64)(RefClk * 40));
+				}
+				else {
+					XVphy_CfgLineRate(InstancePtr, QuadId,
+						XVPHY_CHANNEL_ID_CMNA,
+						(u64)(RefClk * 10));
+				}
+			}
+			/* TX reference clock is in QPLL clock input range.
+			 * In this case don't increase the reference clock, but
+			 * increase the line rate. */
+			else {
+				RefClk = (*RefClkPtr);
+
+				/* Calculate scaled line rate. */
+				if (TxLineRate >= 3400) {
+					XVphy_CfgLineRate(InstancePtr, QuadId,
+						XVPHY_CHANNEL_ID_CMNA,
+						(u64)(RefClk * 40 *SRValue));
+				}
+
+				else {
+					XVphy_CfgLineRate(InstancePtr, QuadId,
+						XVPHY_CHANNEL_ID_CMNA,
+						(u64)(RefClk * 10 *SRValue));
+				}
+			}
+		}
+		/* For all other reference clocks force sample rate to one. */
+		else {
+			SRValue = 1;
+		}
+
+		Status = XVphy_ClkCalcParams(InstancePtr, QuadId, ActiveCmnId,
+						Dir, RefClk);
+		if (Status == (XST_SUCCESS)) {
+			/* Only execute when the TX is using the QPLL. */
+			if (Dir == XVPHY_DIR_TX) {
+				/* Set TX sample rate. */
+				InstancePtr->HdmiTxSampleRate = SRValue;
+
+				/* Set TX TMDS Clock Pattern Generator */
+				if (InstancePtr->Config.UseGtAsTxTmdsClk == TRUE) {
+					XVphy_PatgenSetRatio(InstancePtr, 0, TxLineRate);
+				}
+
+				/* Update reference clock only when the
+				 * reference clock is below the minimum QPLL
+				 * input frequency. */
+				if ((*RefClkPtr) < QpllClkMin) {
+					(*RefClkPtr) = (*RefClkPtr) * SRValue;
+				}
+				else if (SRValue > 1) {
+					XVphy_LogWrite(InstancePtr,
+							XVPHY_LOG_EVT_GT_QPLL_CFG_ERR, 1);
+					XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_QPLL_CFG, 1);
+					XVphy_ErrorHandler(InstancePtr);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+					XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_GT_PLL_LAYOUT, 1);
+					XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_PLL_LAYOUT, 1);
+					XVphy_PllLayoutErrorHandler(InstancePtr);
+#endif
+					return (XST_FAILURE);
+				}
+			}
+			if (Dir == XVPHY_DIR_RX) {
+                XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_NO_DRU, 0);
+			}
+
+			/* Check Userclock Frequency */
+            /* (297 MHz + 0.5%) + 10 KHz (Clkdet accuracy) */
+			if (298495000 <
+					(XVphy_GetLineRateHz(InstancePtr, QuadId,
+							ActiveCmnId) /
+					(InstancePtr->Config.TransceiverWidth * 10))) {
+				XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_USRCLK_ERR, 1);
+				XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_USRCLK, 1);
+				XVphy_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+            XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_QPLL_CFG, 0);
+            XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_USRCLK, 0);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_PLL_LAYOUT, 0);
+#endif
+			return (XST_SUCCESS);
+		}
+	}
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_GT_QPLL_CFG_ERR, 1);
+	XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_QPLL_CFG, 1);
+	XVphy_ErrorHandler(InstancePtr);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_GT_PLL_LAYOUT, 1);
+	XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_PLL_LAYOUT, 1);
+	XVphy_PllLayoutErrorHandler(InstancePtr);
+#endif
+	return (XST_FAILURE);
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the CPLL parameters.
+*
+* @param	InstancePtr is a pointer to the HDMI GT core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if calculated CPLL parameters updated
+*		  successfully.
+*		- XST_FAILURE if parameters not updated.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_HdmiCpllParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir)
+{
+	u32 Status;
+	u64 RefClk = 0;
+	u32 *RefClkPtr;
+	u32 TxLineRate = 0;
+	XVphy_ChannelId ChannelId = XVPHY_CHANNEL_ID_CHA;
+	u8 Id, Id0, Id1;
+
+	u8 SRArray[] = {1, 3, 5};
+	u8 SRIndex;
+	u8 SRValue;
+
+	XVphy_PllType PllType;
+
+	/* Suppress Warning Messages */
+	ChId = ChId;
+
+	/* Change Channel ID to Common if GTPE2 */
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+		PllType = XVphy_GetPllType(InstancePtr, QuadId, Dir,
+				XVPHY_CHANNEL_ID_CH1);
+		if (PllType == XVPHY_PLL_TYPE_PLL0) {
+			ChannelId = XVPHY_CHANNEL_ID_CMN0;
+		}
+		else {
+			ChannelId = XVPHY_CHANNEL_ID_CMN1;
+		}
+	}
+
+	/* TX is using CPLL. */
+	if ((Dir == XVPHY_DIR_TX) && (!XVphy_IsBonded(InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CH1))) {
+
+		/* Set default TX sample rate. */
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		/* Set line rate.  */
+		RefClkPtr = &InstancePtr->HdmiTxRefClkHz;
+		XVphy_CfgLineRate(InstancePtr, QuadId, ChannelId,
+				(u64)((*RefClkPtr) * 10));
+		TxLineRate = (*RefClkPtr)  / 100000;
+
+		/* Check if the line rate is above the 340 Mcsc. */
+		if (TxLineRate >= 3400) {
+			(*RefClkPtr) = (*RefClkPtr) / 4;
+		}
+	}
+	/* RX is using CPLL. */
+	else {
+		RefClkPtr = &InstancePtr->HdmiRxRefClkHz;
+
+		/* Check if the reference clock is not below the minimum CPLL
+		 * input frequency. */
+		if ((*RefClkPtr) >=
+				(GetGtHdmiPtr(InstancePtr))->CpllRefClkMin) {
+			RefClk = (*RefClkPtr);
+
+			/* Scaled linerate */
+			if (InstancePtr->HdmiRxTmdsClockRatio) {
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+					ChannelId, (RefClk * 40));
+			}
+			else {
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+					ChannelId, (RefClk * 10));
+			}
+
+			/* Clear DRU is enabled flag. */
+			InstancePtr->HdmiRxDruIsEnabled = 0;
+
+			/* Set RX data width. */
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+					&Id0, &Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				if ((InstancePtr->Config.TransceiverWidth == 2) ||
+					(InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2)) {
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxDataWidth = 20;
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxIntDataWidth = 2;
+				}
+				else {
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxDataWidth = 40;
+					InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+						RxIntDataWidth = 4;
+				}
+			}
+
+		}
+		/* The reference clock is below the minimum frequency thus
+		 * select the DRU. */
+		else {
+			if (InstancePtr->Config.DruIsPresent) {
+				/* Return config not found error when TMDS ratio is 1/40 */
+                if (InstancePtr->HdmiRxTmdsClockRatio) {
+                    XVphy_LogWrite(InstancePtr,
+                        XVPHY_LOG_EVT_GT_CPLL_CFG_ERR, 1);
+                    XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_CPLL_CFG, 1);
+                    XVphy_ErrorHandler(InstancePtr);
+                    return (XST_FAILURE);
+                }
+
+                RefClk = XVphy_DruGetRefClkFreqHz(InstancePtr);
+                /* Check DRU frequency */
+			if (RefClk == XST_FAILURE) {
+				XVphy_LogWrite(InstancePtr,
+						XVPHY_LOG_EVT_DRU_CLK_ERR, 1);
+				XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_DRU_CLK, 1);
+				XVphy_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+				/* Round input frequency to 10 kHz. */
+				RefClk = (RefClk+5000) / 10000;
+				RefClk = RefClk * 10000;
+
+				/* Set the DRU to operate at a linerate of
+				 * 2.5 Gbps. */
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+						ChannelId,
+#if (XPAR_VPHY_0_TRANSCEIVER != XVPHY_GTXE2)
+						(GetGtHdmiPtr(InstancePtr))->
+						DruLineRate);
+#else
+						XVPHY_HDMI_GTXE2_DRU_LRATE_CPLL);
+#endif
+
+				/* Set DRU is enabled flag. */
+				InstancePtr->HdmiRxDruIsEnabled = 1;
+
+				/* Set RX data width. */
+				XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+						&Id0, &Id1);
+				for (Id = Id0; Id <= Id1; Id++) {
+					InstancePtr->Quads[QuadId].Plls[
+						XVPHY_CH2IDX(Id)].
+						RxDataWidth = 20;
+					InstancePtr->Quads[QuadId].Plls[
+						XVPHY_CH2IDX(Id)].
+						RxIntDataWidth = 2;
+				}
+
+				if (TxLineRate > (((GetGtHdmiPtr(InstancePtr))
+						->DruLineRate) / 1000000)) {
+					XVphy_LogWrite(InstancePtr,
+							XVPHY_LOG_EVT_VD_NOT_SPRTD_ERR, 1);
+                    XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_CPLL_CFG, 1);
+                    XVphy_ErrorHandler(InstancePtr);
+                    return (XST_FAILURE);
+				}
+			}
+			else {
+				/* Return config not found error when TMDS ratio is 1/40 */
+                if (InstancePtr->HdmiRxTmdsClockRatio) {
+                    XVphy_LogWrite(InstancePtr,
+                        XVPHY_LOG_EVT_GT_CPLL_CFG_ERR, 1);
+                    XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_CPLL_CFG, 1);
+                    XVphy_ErrorHandler(InstancePtr);
+                }
+                else {
+					XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_NO_DRU, 1);
+					XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_NO_DRU, 1);
+					XVphy_ErrorHandler(InstancePtr);
+                }
+                return (XST_FAILURE);
+			}
+		}
+	}
+
+	/* Try different sample rates. */
+	for (SRIndex = 0; SRIndex < sizeof(SRArray); SRIndex++) {
+		/* Only use oversampling when then TX is using the CPLL. */
+		if ((Dir == XVPHY_DIR_TX) && (!XVphy_IsBonded(InstancePtr,
+					QuadId, XVPHY_CHANNEL_ID_CH1))) {
+			SRValue = SRArray[SRIndex];
+
+			/* Multiply the reference clock with the sample rate
+			 * value. */
+			RefClk = ((*RefClkPtr) * SRValue);
+
+			/* Calculate scaled line rate. */
+			if (TxLineRate >= 3400) {
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+					ChannelId, (RefClk * 40));
+			}
+			else {
+				XVphy_CfgLineRate(InstancePtr, QuadId,
+					ChannelId, (RefClk * 10));
+			}
+		}
+		/* For all other reference clocks force sample rate to one. */
+		else {
+			SRValue = 1;
+		}
+
+		Status = XVphy_ClkCalcParams(InstancePtr, QuadId,
+					ChannelId, Dir, RefClk);
+		if (Status == (XST_SUCCESS)) {
+			/* Only execute when the TX is using the QPLL. */
+			if ((Dir == XVPHY_DIR_TX) && (!XVphy_IsBonded(
+					InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CH1))) {
+				InstancePtr->HdmiTxSampleRate = SRValue;
+
+				/* Set TX TMDS Clock Pattern Generator */
+				if (InstancePtr->Config.UseGtAsTxTmdsClk == TRUE) {
+					XVphy_PatgenSetRatio(InstancePtr, 0, TxLineRate);
+				}
+
+				(*RefClkPtr) = (*RefClkPtr) * SRValue;
+			}
+			if (Dir == XVPHY_DIR_RX) {
+                XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_NO_DRU, 0);
+                XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_DRU_CLK, 0);
+			}
+
+			/* Check Userclock Frequency */
+            /* (297 MHz + 0.5%) + 10 KHz (Clkdet accuracy) */
+			if (298495000 <
+					(XVphy_GetLineRateHz(InstancePtr, QuadId,
+							XVPHY_CHANNEL_ID_CH1) /
+					(InstancePtr->Config.TransceiverWidth * 10))) {
+				XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_USRCLK_ERR, 1);
+				XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_USRCLK, 1);
+				XVphy_ErrorHandler(InstancePtr);
+				return (XST_FAILURE);
+			}
+
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_USRCLK, 0);
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_CPLL_CFG, 0);
+			return (XST_SUCCESS);
+		}
+	}
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_GT_CPLL_CFG_ERR, 1);
+	XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_CPLL_CFG, 1);
+	XVphy_ErrorHandler(InstancePtr);
+	return (XST_FAILURE);
+}
+
+/*****************************************************************************/
+/**
+* This function update/set the HDMI TX parameter.
+*
+* @param	InstancePtr is a pointer to the Vphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Ppc is the pixels per clock to set.
+* @param	Bpc is the bits per color to set.
+* @param	ColorFormat is the color format to set.
+*
+* @return
+*		- XST_SUCCESS if TX parameters set/updated.
+*		- XST_FAILURE if low resolution video not supported.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_SetHdmiTxParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVidC_PixelsPerClock Ppc, XVidC_ColorDepth Bpc,
+		XVidC_ColorFormat ColorFormat)
+{
+	u32 Status;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid((Ppc == (XVIDC_PPC_1)) || (Ppc == (XVIDC_PPC_2)) ||
+			(Ppc == (XVIDC_PPC_4)));
+	Xil_AssertNonvoid((Bpc == (XVIDC_BPC_8)) || (Bpc == (XVIDC_BPC_10)) ||
+			(Bpc == (XVIDC_BPC_12)) || (Bpc == (XVIDC_BPC_16)));
+	Xil_AssertNonvoid((ColorFormat == (XVIDC_CSF_RGB)) ||
+			(ColorFormat == (XVIDC_CSF_YCRCB_444)) ||
+			(ColorFormat == (XVIDC_CSF_YCRCB_422)) ||
+			(ColorFormat == (XVIDC_CSF_YCRCB_420)));
+
+	/* Only calculate the QPLL/CPLL parameters when the GT TX and RX are not
+	 * coupled. */
+	if (!XVphy_IsBonded(InstancePtr, QuadId, ChId)) {
+		if (XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+			Status = XVphy_HdmiCpllParam(InstancePtr, QuadId, ChId,
+					XVPHY_DIR_TX);
+		}
+		else if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+			Status = XVphy_HdmiQpllParam(InstancePtr, QuadId, ChId,
+					XVPHY_DIR_TX);
+			/* Update SysClk and PLL Clk registers immediately. */
+			XVphy_WriteCfgRefClkSelReg(InstancePtr, QuadId);
+		}
+		else {
+			/* GTP divider calculation is same with CPLL */
+			Status = XVphy_HdmiCpllParam(InstancePtr, QuadId, ChId,
+			XVPHY_DIR_TX);
+		}
+
+		if (Status == XST_FAILURE) {
+			return Status;
+		}
+	}
+	/* Bonded mode. */
+	else {
+		/* Copy reference clock. */
+		InstancePtr->HdmiTxRefClkHz = InstancePtr->HdmiRxRefClkHz;
+
+		/* Copy the line rate. */
+		if (XVphy_IsRxUsingQpll(InstancePtr, QuadId,
+					XVPHY_CHANNEL_ID_CH1)) {
+			InstancePtr->Quads[QuadId].Ch1.LineRateHz =
+				InstancePtr->Quads[QuadId].Cmn0.LineRateHz;
+		}
+		else {
+			InstancePtr->Quads[QuadId].Cmn0.LineRateHz =
+				InstancePtr->Quads[QuadId].Ch1.LineRateHz;
+		}
+
+		InstancePtr->HdmiTxSampleRate = 1;
+
+		Status = (XST_SUCCESS);
+	}
+
+	/* Is HDMITXSS PPC match with VPHY PPC? */
+	if (Ppc == InstancePtr->Config.Ppc) {
+		XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_VD_NOT_SPRTD, 0);
+		Status = (XST_SUCCESS);
+	}
+	else {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_PPC_MSMTCH_ERR, 1);
+		XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_VD_NOT_SPRTD, 1);
+		XVphy_ErrorHandler(InstancePtr);
+		Status = (XST_FAILURE);
+	}
+	if (Status == (XST_SUCCESS)) {
+		/* Calculate TXPLL parameters.
+		 * In HDMI the colordepth in YUV422 is always 12 bits,
+		 * although on the link itself it is being transmitted as
+		 * 8-bits. Therefore if the colorspace is YUV422, then force the
+		 * colordepth to 8 bits. */
+		if (ColorFormat == XVIDC_CSF_YCRCB_422) {
+			Status = XVphy_HdmiCfgCalcMmcmParam(InstancePtr, QuadId,
+				ChId, XVPHY_DIR_TX, Ppc, XVIDC_BPC_8);
+		}
+		/* Other colorspaces. */
+		else {
+			Status = XVphy_HdmiCfgCalcMmcmParam(InstancePtr, QuadId,
+				ChId, XVPHY_DIR_TX, Ppc, Bpc);
+		}
+	}
+	else {
+		Status = (XST_FAILURE);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function update/set the HDMI RX parameter.
+*
+* @param	InstancePtr is a pointer to the Vphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if RX parameters set/updated.
+*		- XST_FAILURE if low resolution video not supported.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_SetHdmiRxParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	XVphy_ChannelId ChanId = ChId;
+	XVphy_PllType PllType;
+	u32 Status;
+	u64 DruCenterFreq;
+	u8 Id, Id0, Id1;
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	if (XVphy_IsRxUsingCpll(InstancePtr, QuadId, ChId)) {
+		Status = XVphy_HdmiCpllParam(InstancePtr, QuadId, ChId,
+				XVPHY_DIR_RX);
+	}
+	else if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		Status = XVphy_HdmiQpllParam(InstancePtr, QuadId, ChId,
+				XVPHY_DIR_RX);
+		/* Update SysClk and PLL Clk registers immediately */
+		XVphy_WriteCfgRefClkSelReg(InstancePtr, QuadId);
+	}
+	else {
+		/* GTP divider calculation is same with CPLL */
+		Status = XVphy_HdmiCpllParam(InstancePtr, QuadId, ChId,
+				XVPHY_DIR_RX);
+	}
+
+	if (XVphy_IsBonded(InstancePtr, QuadId, XVPHY_CHANNEL_ID_CH1)) {
+		/* Same divisor value for all channels. */
+		XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+		for (Id = Id0; Id <= Id1; Id++) {
+			InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].
+				TxOutDiv = InstancePtr->Quads[QuadId].
+				Plls[XVPHY_CH2IDX(Id)].RxOutDiv;
+		}
+	}
+
+	if (InstancePtr->HdmiRxDruIsEnabled) {
+		/* Determine PLL type. */
+		PllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+				XVPHY_CHANNEL_ID_CH1);
+		/* Update the ChId */
+		ChanId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_RX, PllType);
+
+		DruCenterFreq = XVphy_DruCalcCenterFreqHz(InstancePtr, QuadId,
+					ChanId);
+		XVphy_DruSetCenterFreqHz(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+						DruCenterFreq);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function sets the Pattern Generator for the GT Channel 4 when it is
+* used to generate the TX TMDS Clock.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_PatgenSetRatio(XVphy *InstancePtr, u8 QuadId, u64 TxLineRate)
+{
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+    QuadId = QuadId;
+
+	RegVal = (XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+							XVPHY_PATGEN_CTRL_REG)
+				& ~XVPHY_PATGEN_CTRL_RATIO_MASK);
+
+	if ((TxLineRate >= 3400) && (InstancePtr->HdmiTxSampleRate == 1)) {
+		RegVal |= XVPHY_Patgen_Ratio_40 & XVPHY_PATGEN_CTRL_RATIO_MASK;
+	}
+	else {
+		RegVal |= InstancePtr->HdmiTxSampleRate &
+						XVPHY_PATGEN_CTRL_RATIO_MASK;
+	}
+
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+						XVPHY_PATGEN_CTRL_REG, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function prints Video PHY debug information related to HDMI.
+*
+* @param	InstancePtr is a pointer to the Vphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	buff Buffer to print to
+* @param	buff_size Maximum size of buff
+*
+* @return	Number of characters printed in buff.
+*
+* @note		None.
+*
+******************************************************************************/
+int XVphy_HdmiDebugInfo(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		char *buff, int buff_size)
+{
+	int strSize = 0;
+	u32 RegValue;
+	XVphy_Channel *ChPtr;
+	XVphy_ChannelId CmnId = XVPHY_CHANNEL_ID_CMN0;
+	u8 CpllDVal;
+	u8 QpllDVal;
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+	u8 UsesQpll0 = 0;
+#endif
+	u8 TxUsesPll0 = 0;
+
+	ChPtr = &InstancePtr->Quads[QuadId].Plls[0];
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+	if (ChPtr->TxDataRefClkSel ==
+			XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK) {
+		TxUsesPll0 = 1;
+	}
+#endif
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+		if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+			UsesQpll0 = (FALSE);
+#endif
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: PLL%d\n", (TxUsesPll0 ? 0 : 1));
+		}
+		else if (XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: CPLL\n");
+		}
+		else {
+			if ((ChPtr->TxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK) ||
+				(ChPtr->TxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK)) {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+				UsesQpll0 = (TRUE);
+#endif
+				CmnId = XVPHY_CHANNEL_ID_CMN0;
+			}
+			else {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+				UsesQpll0 = (FALSE);
+#endif
+				CmnId = XVPHY_CHANNEL_ID_CMN1;
+			}
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: QPLL%d\n", (UsesQpll0 ? 0 : 1));
+#else
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX: QPLL\n");
+#endif
+		}
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: PLL%d\n", (TxUsesPll0 ? 1 : 0));
+		}
+		else if (XVphy_IsRxUsingCpll(InstancePtr, QuadId, ChId)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: CPLL\n");
+		}
+		else {
+			if ((ChPtr->RxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK) ||
+				(ChPtr->RxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK)) {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+				UsesQpll0 = (TRUE);
+#endif
+				CmnId = XVPHY_CHANNEL_ID_CMN0;
+			}
+			else {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+				UsesQpll0 = (FALSE);
+#endif
+				CmnId = XVPHY_CHANNEL_ID_CMN1;
+			}
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: QPLL%d\n", (UsesQpll0 ? 0 : 1));
+#else
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX: QPLL\n");
+#endif
+		}
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"TX state: ");
+		switch (InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].TxState) {
+		case (XVPHY_GT_STATE_IDLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"idle\n");
+			break;
+		case (XVPHY_GT_STATE_LOCK):
+			if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"PLL%d lock\n", (TxUsesPll0 ? 0 : 1));
+			}
+			else if (XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"CPLL lock\n");
+			}
+			else {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL%d lock\n", (UsesQpll0 ? 0 : 1));
+#else
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL lock\n");
+#endif
+			}
+			break;
+		case (XVPHY_GT_STATE_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GT reset\n");
+			break;
+		case (XVPHY_GT_STATE_ALIGN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,	
+				"align\n");
+			break;
+		case (XVPHY_GT_STATE_READY):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ready\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"unknown\n");
+			break;
+		}
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"RX state: ");
+		switch (InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].RxState) {
+		case (XVPHY_GT_STATE_IDLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"idle\n");
+			break;
+		case (XVPHY_GT_STATE_LOCK):
+			if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"PLL%d lock\n", (TxUsesPll0 ? 1 : 0));
+			}
+			else if (XVphy_IsRxUsingCpll(InstancePtr, QuadId, ChId)) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"CPLL lock\n");
+			}
+			else {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL%d lock\n", (UsesQpll0 ? 0 : 1));
+#else
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL lock\n");
+#endif
+			}
+			break;
+		case (XVPHY_GT_STATE_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"GT reset\n");
+			break;
+		case (XVPHY_GT_STATE_READY):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ready\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"unknown\n");
+			break;
+		}
+	}
+
+	if (XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId)) {
+		QpllDVal = ChPtr->RxOutDiv;
+		CpllDVal = ChPtr->TxOutDiv;
+	}
+	else {
+		CpllDVal = ChPtr->RxOutDiv;
+		QpllDVal = ChPtr->TxOutDiv;
+	}
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize, "\n");
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		if ((XVphy_IsTxUsingQpll(InstancePtr, QuadId, ChId) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX))) ||
+			(XVphy_IsRxUsingQpll(InstancePtr, QuadId, ChId) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)))) {
+#if ((XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4) || \
+	 (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4))
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"QPLL%d settings\n", (UsesQpll0 ? 0 : 1));
+#else
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"QPLL settings\n");
+#endif
+			strSize += scnprintf(buff+strSize, buff_size-strSize,	
+				"-------------\n" \
+				"M : %d - N : %d - D : %d\n\n",
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.MRefClkDiv,
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.NFbDiv, QpllDVal);
+		}
+
+		if ((XVphy_IsTxUsingCpll(InstancePtr, QuadId, ChId) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX))) ||
+			(XVphy_IsRxUsingCpll(InstancePtr, QuadId, ChId) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)))) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"CPLL settings\n" \
+				"-------------\n" \
+				"M : %d - N1 : %d - N2 : %d - D : %d\n\n",
+				ChPtr->PllParams.MRefClkDiv,
+				ChPtr->PllParams.N1FbDiv, ChPtr->PllParams.N2FbDiv,
+				CpllDVal);
+		}
+	}
+	else {
+		if (((ChPtr->TxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX))) ||
+			((ChPtr->RxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)))) {
+			CmnId = XVPHY_CHANNEL_ID_CMN0;
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"PLL0 settings\n" \
+				"-------------\n" \
+				"M : %d - N1 : %d - N2 : %d - D : %d\n\n",
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.MRefClkDiv,
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.N1FbDiv,
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.N2FbDiv,
+				(TxUsesPll0 ? ChPtr->TxOutDiv : ChPtr->RxOutDiv));
+
+		}
+
+		if (((ChPtr->TxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_PLL1_OUTCLK) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX))) ||
+			((ChPtr->RxDataRefClkSel ==
+					XVPHY_SYSCLKSELDATA_TYPE_PLL1_OUTCLK) &&
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)))) {
+			CmnId = XVPHY_CHANNEL_ID_CMN1;
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"PLL1 settings\n"
+				"-------------\n"
+				"M : %d - N1 : %d - N2 : %d - D : %d\n\n",
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.MRefClkDiv,
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.N1FbDiv,
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(CmnId)].
+					PllParams.N2FbDiv,
+				(TxUsesPll0 ? ChPtr->RxOutDiv : ChPtr->TxOutDiv));
+		}
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"RX MMCM settings\n"
+			"-------------\n"
+			"Mult : %d - Div : %d - Clk0Div : %d - Clk1Div : %d - "
+			   "Clk2Div : %d\n\n",
+			InstancePtr->Quads[QuadId].RxMmcm.ClkFbOutMult,
+			InstancePtr->Quads[QuadId].RxMmcm.DivClkDivide,
+			InstancePtr->Quads[QuadId].RxMmcm.ClkOut0Div,
+			InstancePtr->Quads[QuadId].RxMmcm.ClkOut1Div,
+			InstancePtr->Quads[QuadId].RxMmcm.ClkOut2Div);
+	}
+
+	if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"TX MMCM settings\n" \
+			"-------------\n" \
+			"Mult : %d - Div : %d - Clk0Div : %d - Clk1Div : %d - "
+			   "Clk2Div : %d\n\n",
+			InstancePtr->Quads[QuadId].TxMmcm.ClkFbOutMult,
+			InstancePtr->Quads[QuadId].TxMmcm.DivClkDivide,
+			InstancePtr->Quads[QuadId].TxMmcm.ClkOut0Div,
+			InstancePtr->Quads[QuadId].TxMmcm.ClkOut1Div,
+			InstancePtr->Quads[QuadId].TxMmcm.ClkOut2Div);
+	}
+
+	if ((InstancePtr->Config.DruIsPresent) &&
+		(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)))	{
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"DRU Settings\n" \
+			"-------------\n");
+		RegValue = XVphy_DruGetVersion(InstancePtr);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"Version  : %d\n", RegValue);
+
+		if (InstancePtr->HdmiRxDruIsEnabled) {
+			RegValue = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+					XVPHY_DRU_GAIN_REG(ChId));
+
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"G1       : %d\nG1_P     : %d\n"
+				"G2       : %d\n",
+				((RegValue & XVPHY_DRU_GAIN_G1_MASK)),
+				((RegValue & XVPHY_DRU_GAIN_G1_P_MASK) >>
+					XVPHY_DRU_GAIN_G1_P_SHIFT),
+				((RegValue & XVPHY_DRU_GAIN_G2_MASK) >>
+					XVPHY_DRU_GAIN_G2_SHIFT));
+
+			RegValue = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+				XVPHY_DRU_CFREQ_H_REG(ChId));
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Center_F : %x", RegValue);
+
+			RegValue = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+				XVPHY_DRU_CFREQ_L_REG(ChId));
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"%x\n", RegValue);
+		}
+		else {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"DRU is disabled\n");
+		}
+
+		strSize += scnprintf(buff+strSize, buff_size-strSize," \n");
+	}
+	return strSize;
+}
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+static const XVphy_GtHdmiChars Gthe3HdmiChars = {
+	.DruLineRate = XVPHY_HDMI_GTHE3_DRU_LRATE,
+	.PllScale = XVPHY_HDMI_GTHE3_PLL_SCALE,
+	.Qpll0RefClkMin = XVPHY_HDMI_GTHE3_QPLL0_REFCLK_MIN,
+	.Qpll1RefClkMin = XVPHY_HDMI_GTHE3_QPLL1_REFCLK_MIN,
+	.CpllRefClkMin = XVPHY_HDMI_GTHE3_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XVPHY_HDMI_GTHE3_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XVPHY_HDMI_GTHE3_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XVPHY_HDMI_GTHE3_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XVPHY_HDMI_GTHE3_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XVPHY_HDMI_GTHE3_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XVPHY_HDMI_GTHE3_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+static const XVphy_GtHdmiChars Gthe4HdmiChars = {
+	.DruLineRate = XVPHY_HDMI_GTHE4_DRU_LRATE,
+	.PllScale = XVPHY_HDMI_GTHE4_PLL_SCALE,
+	.Qpll0RefClkMin = XVPHY_HDMI_GTHE4_QPLL0_REFCLK_MIN,
+	.Qpll1RefClkMin = XVPHY_HDMI_GTHE4_QPLL1_REFCLK_MIN,
+	.CpllRefClkMin = XVPHY_HDMI_GTHE4_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XVPHY_HDMI_GTHE4_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XVPHY_HDMI_GTHE4_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XVPHY_HDMI_GTHE4_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XVPHY_HDMI_GTHE4_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XVPHY_HDMI_GTHE4_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XVPHY_HDMI_GTHE4_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+static const XVphy_GtHdmiChars Gtye4HdmiChars = {
+	.DruLineRate = XVPHY_HDMI_GTYE4_DRU_LRATE,
+	.PllScale = XVPHY_HDMI_GTYE4_PLL_SCALE,
+	.Qpll0RefClkMin = XVPHY_HDMI_GTYE4_QPLL0_REFCLK_MIN,
+	.Qpll1RefClkMin = XVPHY_HDMI_GTYE4_QPLL1_REFCLK_MIN,
+	.CpllRefClkMin = XVPHY_HDMI_GTYE4_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XVPHY_HDMI_GTYE4_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XVPHY_HDMI_GTYE4_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XVPHY_HDMI_GTYE4_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XVPHY_HDMI_GTYE4_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XVPHY_HDMI_GTYE4_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XVPHY_HDMI_GTYE4_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+static const XVphy_GtHdmiChars Gthe2HdmiChars = {
+	.DruLineRate = XVPHY_HDMI_GTHE2_DRU_LRATE,
+	.PllScale = XVPHY_HDMI_GTHE2_PLL_SCALE,
+	.Qpll0RefClkMin = XVPHY_HDMI_GTHE2_QPLL_REFCLK_MIN,
+	.Qpll1RefClkMin = 0,
+	.CpllRefClkMin = XVPHY_HDMI_GTHE2_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XVPHY_HDMI_GTHE2_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XVPHY_HDMI_GTHE2_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XVPHY_HDMI_GTHE2_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XVPHY_HDMI_GTHE2_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XVPHY_HDMI_GTHE2_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XVPHY_HDMI_GTHE2_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+static const XVphy_GtHdmiChars Gtpe2HdmiChars = {
+	.DruLineRate = XVPHY_HDMI_GTPE2_DRU_LRATE,
+	.PllScale = XVPHY_HDMI_GTPE2_PLL_SCALE,
+	.Qpll0RefClkMin = XVPHY_HDMI_GTPE2_QPLL_REFCLK_MIN,
+	.Qpll1RefClkMin = 0,
+	.CpllRefClkMin = XVPHY_HDMI_GTPE2_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XVPHY_HDMI_GTPE2_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XVPHY_HDMI_GTPE2_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XVPHY_HDMI_GTPE2_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XVPHY_HDMI_GTPE2_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XVPHY_HDMI_GTPE2_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XVPHY_HDMI_GTPE2_RX_MMCM_FVCO_MAX,
+};
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+static const XVphy_GtHdmiChars Gtxe2HdmiChars = {
+	.DruLineRate = XVPHY_HDMI_GTXE2_DRU_LRATE,
+	.PllScale = XVPHY_HDMI_GTXE2_PLL_SCALE,
+	.Qpll0RefClkMin = XVPHY_HDMI_GTXE2_QPLL_REFCLK_MIN,
+	.Qpll1RefClkMin = 0,
+	.CpllRefClkMin = XVPHY_HDMI_GTXE2_CPLL_REFCLK_MIN,
+	.TxMmcmScale = XVPHY_HDMI_GTXE2_TX_MMCM_SCALE,
+	.TxMmcmFvcoMin = XVPHY_HDMI_GTXE2_TX_MMCM_FVCO_MIN,
+	.TxMmcmFvcoMax = XVPHY_HDMI_GTXE2_TX_MMCM_FVCO_MAX,
+	.RxMmcmScale = XVPHY_HDMI_GTXE2_RX_MMCM_SCALE,
+	.RxMmcmFvcoMin = XVPHY_HDMI_GTXE2_RX_MMCM_FVCO_MIN,
+	.RxMmcmFvcoMax = XVPHY_HDMI_GTXE2_RX_MMCM_FVCO_MAX,
+};
+#endif
+
+/*****************************************************************************/
+/**
+* This function returns a pointer to the HDMI parameters based on the GT type.
+*
+* @param	InstancePtr is a pointer to the Vphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- A pointer to the HDMI GT characteristics.
+*		- NULL if the GT type is unsupported.
+*
+* @note		None.
+*
+******************************************************************************/
+static const XVphy_GtHdmiChars *GetGtHdmiPtr(XVphy *InstancePtr)
+{
+	/* Suppress Warning Messages */
+	InstancePtr = InstancePtr;
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	return &Gtxe2HdmiChars;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE2)
+	return &Gthe2HdmiChars;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+	return &Gtpe2HdmiChars;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE3)
+	return &Gthe3HdmiChars;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4)
+	return &Gthe4HdmiChars;
+#elif (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+	return &Gtye4HdmiChars;
+#endif
+
+	return NULL;
+}
+
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hdmi.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hdmi.h
@@ -0,0 +1,178 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_hdmi.h
+ *
+ * The Xilinx Video PHY (VPHY) driver. This driver supports the Xilinx Video PHY
+ * IP core.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Added GTPE2 and GTHE4 constants
+ * 1.2   gm            Added XVphy_HdmiMmcmStart function
+ * 1.4   gm   29/11/16 Added preprocessor directives for sw footprint reduction
+ *                     Removed XVphy_HdmiMmcmStart API
+ *                     Corrected GTPE2 DRU REFCLK range
+ * 1.6   gm   03/07/17 Added XVPHY_HDMI_GTXE2_DRU_LRATE_Q/CPLL definitions
+ *                     Corrected FVCO range for MMCME4
+ * 1.7   gm   13/09/17 Removed XVphy_DruSetGain API
+ * </pre>
+ *
+ * @{
+*******************************************************************************/
+#if defined (XPAR_XV_HDMITX_0_DEVICE_ID) || defined (XPAR_XV_HDMIRX_0_DEVICE_ID)
+
+#ifndef XVPHY_HDMI_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XVPHY_HDMI_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/************************** Constant Definitions ******************************/
+
+#define XVPHY_HDMI_GTYE4_DRU_LRATE			2500000000U
+#define XVPHY_HDMI_GTYE4_DRU_REFCLK			156250000LL
+#define XVPHY_HDMI_GTYE4_DRU_REFCLK_MIN		156240000LL
+#define XVPHY_HDMI_GTYE4_DRU_REFCLK_MAX		156260000LL
+#define XVPHY_HDMI_GTYE4_PLL_SCALE			1000
+#define XVPHY_HDMI_GTYE4_QPLL0_REFCLK_MIN	61250000LL
+#define XVPHY_HDMI_GTYE4_QPLL1_REFCLK_MIN	50000000LL
+#define XVPHY_HDMI_GTYE4_CPLL_REFCLK_MIN	50000000LL
+#define XVPHY_HDMI_GTYE4_TX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTYE4_TX_MMCM_FVCO_MIN	800000000U
+#define XVPHY_HDMI_GTYE4_TX_MMCM_FVCO_MAX	1600000000U
+#define XVPHY_HDMI_GTYE4_RX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTYE4_RX_MMCM_FVCO_MIN	800000000U
+#define XVPHY_HDMI_GTYE4_RX_MMCM_FVCO_MAX	1600000000U
+
+#define XVPHY_HDMI_GTHE4_DRU_LRATE			2500000000U
+#define XVPHY_HDMI_GTHE4_DRU_REFCLK			156250000LL
+#define XVPHY_HDMI_GTHE4_DRU_REFCLK_MIN		156240000LL
+#define XVPHY_HDMI_GTHE4_DRU_REFCLK_MAX		156260000LL
+#define XVPHY_HDMI_GTHE4_PLL_SCALE			1000
+#define XVPHY_HDMI_GTHE4_QPLL0_REFCLK_MIN	61250000LL
+#define XVPHY_HDMI_GTHE4_QPLL1_REFCLK_MIN	50000000LL
+#define XVPHY_HDMI_GTHE4_CPLL_REFCLK_MIN	50000000LL
+#define XVPHY_HDMI_GTHE4_TX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTHE4_TX_MMCM_FVCO_MIN	800000000U
+#define XVPHY_HDMI_GTHE4_TX_MMCM_FVCO_MAX	1600000000U
+#define XVPHY_HDMI_GTHE4_RX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTHE4_RX_MMCM_FVCO_MIN	800000000U
+#define XVPHY_HDMI_GTHE4_RX_MMCM_FVCO_MAX	1600000000U
+
+#define XVPHY_HDMI_GTHE3_DRU_LRATE			2500000000U
+#define XVPHY_HDMI_GTHE3_DRU_REFCLK			156250000LL
+#define XVPHY_HDMI_GTHE3_DRU_REFCLK_MIN		156240000LL
+#define XVPHY_HDMI_GTHE3_DRU_REFCLK_MAX		156260000LL
+#define XVPHY_HDMI_GTHE3_PLL_SCALE			1000
+#define XVPHY_HDMI_GTHE3_QPLL0_REFCLK_MIN	61250000LL
+#define XVPHY_HDMI_GTHE3_QPLL1_REFCLK_MIN	50000000LL
+#define XVPHY_HDMI_GTHE3_CPLL_REFCLK_MIN	50000000LL
+#define XVPHY_HDMI_GTHE3_TX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTHE3_TX_MMCM_FVCO_MIN	600000000U
+#define XVPHY_HDMI_GTHE3_TX_MMCM_FVCO_MAX	1200000000U
+#define XVPHY_HDMI_GTHE3_RX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTHE3_RX_MMCM_FVCO_MIN	600000000U
+#define XVPHY_HDMI_GTHE3_RX_MMCM_FVCO_MAX	1200000000U
+
+#define XVPHY_HDMI_GTHE2_DRU_LRATE			2500000000U
+#define XVPHY_HDMI_GTHE2_DRU_REFCLK			125000000LL
+#define XVPHY_HDMI_GTHE2_DRU_REFCLK_MIN		124990000LL
+#define XVPHY_HDMI_GTHE2_DRU_REFCLK_MAX		125010000LL
+#define XVPHY_HDMI_GTHE2_PLL_SCALE			1000
+#define XVPHY_HDMI_GTHE2_QPLL_REFCLK_MIN	61250000LL
+#define XVPHY_HDMI_GTHE2_CPLL_REFCLK_MIN	80000000LL
+#define XVPHY_HDMI_GTHE2_TX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTHE2_TX_MMCM_FVCO_MIN	600000000U
+#define XVPHY_HDMI_GTHE2_TX_MMCM_FVCO_MAX	1200000000U
+#define XVPHY_HDMI_GTHE2_RX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTHE2_RX_MMCM_FVCO_MIN	600000000U
+#define XVPHY_HDMI_GTHE2_RX_MMCM_FVCO_MAX	1200000000U
+
+#define XVPHY_HDMI_GTXE2_DRU_LRATE_QPLL		2000000000U
+#define XVPHY_HDMI_GTXE2_DRU_LRATE_CPLL		2500000000U
+#define XVPHY_HDMI_GTXE2_DRU_LRATE			2500000000U
+#define XVPHY_HDMI_GTXE2_DRU_REFCLK			125000000LL
+#define XVPHY_HDMI_GTXE2_DRU_REFCLK_MIN		124990000LL
+#define XVPHY_HDMI_GTXE2_DRU_REFCLK_MAX		125010000LL
+#define XVPHY_HDMI_GTXE2_PLL_SCALE			1000
+#define XVPHY_HDMI_GTXE2_QPLL_REFCLK_MIN	74125000LL
+#define XVPHY_HDMI_GTXE2_CPLL_REFCLK_MIN	80000000LL
+#define XVPHY_HDMI_GTXE2_TX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTXE2_TX_MMCM_FVCO_MIN	800000000U
+#define XVPHY_HDMI_GTXE2_TX_MMCM_FVCO_MAX	1866000000U
+#define XVPHY_HDMI_GTXE2_RX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTXE2_RX_MMCM_FVCO_MIN	600000000U
+#define XVPHY_HDMI_GTXE2_RX_MMCM_FVCO_MAX	1200000000U
+
+#define XVPHY_HDMI_GTPE2_DRU_LRATE			2500000000U
+#define XVPHY_HDMI_GTPE2_DRU_REFCLK			100000000LL
+#define XVPHY_HDMI_GTPE2_DRU_REFCLK_MIN	 	99990000LL
+#define XVPHY_HDMI_GTPE2_DRU_REFCLK_MAX		100010000LL
+#define XVPHY_HDMI_GTPE2_PLL_SCALE			1000
+#define XVPHY_HDMI_GTPE2_QPLL_REFCLK_MIN	80000000LL
+#define XVPHY_HDMI_GTPE2_CPLL_REFCLK_MIN	80000000LL
+#define XVPHY_HDMI_GTPE2_TX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTPE2_TX_MMCM_FVCO_MIN	800000000U
+#define XVPHY_HDMI_GTPE2_TX_MMCM_FVCO_MAX	1866000000U
+#define XVPHY_HDMI_GTPE2_RX_MMCM_SCALE		1
+#define XVPHY_HDMI_GTPE2_RX_MMCM_FVCO_MIN	600000000U
+#define XVPHY_HDMI_GTPE2_RX_MMCM_FVCO_MAX	1200000000U
+
+/**************************** Function Prototypes *****************************/
+
+u32 XVphy_HdmiQpllParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir);
+u32 XVphy_HdmiCpllParam(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir);
+void XVphy_TxAlignReset(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Reset);
+void XVphy_TxAlignStart(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Start);
+void XVphy_ClkDetEnable(XVphy *InstancePtr, u8 Enable);
+void XVphy_ClkDetTimerClear(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir);
+void XVphy_ClkDetSetFreqLockThreshold(XVphy *InstancePtr, u16 ThresholdVal);
+u8 XVphy_ClkDetCheckFreqZero(XVphy *InstancePtr, XVphy_DirectionType Dir);
+void XVphy_ClkDetSetFreqTimeout(XVphy *InstancePtr, u32 TimeoutVal);
+void XVphy_ClkDetTimerLoad(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, u32 TimeoutVal);
+void XVphy_DruReset(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Reset);
+void XVphy_DruEnable(XVphy *InstancePtr, XVphy_ChannelId ChId, u8 Enable);
+u16 XVphy_DruGetVersion(XVphy *InstancePtr);
+void XVphy_DruSetCenterFreqHz(XVphy *InstancePtr, XVphy_ChannelId ChId,
+		u64 CenterFreqHz);
+u64 XVphy_DruCalcCenterFreqHz(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId);
+void XVphy_HdmiGtDruModeEnable(XVphy *InstancePtr, u8 Enable);
+void XVphy_PatgenSetRatio(XVphy *InstancePtr, u8 QuadId, u64 TxLineRate);
+void XVphy_HdmiIntrHandlerCallbackInit(XVphy *InstancePtr);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XVPHY_HDMI_H_ */
+#endif
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hdmi_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hdmi_intr.c
@@ -0,0 +1,1271 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_hdmi_intr.c
+ *
+ * This file contains video PHY functionality specific to the HDMI protocol
+ * related to interrupts.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Added GTPE2 and GTHE4 support
+ *                     Added XVphy_HdmiGtpPllLockHandler for GTPE2
+ * 1.2   gm            Replaced xil_printf with log events for debugging
+ * 1.3   gm   01/11/16 Fixed rounding of RX refclk frequency
+ *                     Fixed race condition in
+ *                       XVphy_HdmiRxClkDetFreqChangeHandler when  storing
+ *                       RxRefClkHz value
+ * 1.4   gm   29/11/16 Added preprocessor directives for sw footprint reduction
+ *                     Incorporated AXIlite Freq auto extraction
+ *                     Added logging and register access for ERR_IRQ impl
+ *                     Added mechanism to re-trigger GT TX reset when TX align
+ *                       get stuck
+ *                     Fixed c++ compiler warnings
+ * 1.6   gm   06/08/17 Prevented TX reset on bonded mode and when DRU is active
+ *                       in XVphy_HdmiGtRxResetDoneLockHandler API
+ *                     Added TX and RX MMCM Lock handling
+ *                     Improved TX initialization flow in bonded mode to
+ *                       reset GT TX only when PLL and MMCM are locked
+ * 1.7   gm   13/09/17 Added GTYE4 support
+ * 1.9   gm   14/05/18 Added TX and RX MMCM lock event logging
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#if defined (XPAR_XV_HDMITX_0_DEVICE_ID) || defined (XPAR_XV_HDMIRX_0_DEVICE_ID)
+#include "xstatus.h"
+#include "xvphy.h"
+#include "xvphy_i.h"
+#include "xvphy_hdmi.h"
+#include "xvphy_gt.h"
+
+/************************** Function Prototypes ******************************/
+
+extern void XVphy_Ch2Ids(XVphy *InstancePtr, XVphy_ChannelId ChId,
+		u8 *Id0, u8 *Id1);
+
+static void XVphy_HdmiGtHandler(XVphy *InstancePtr);
+static void XVphy_ClkDetHandler(XVphy *InstancePtr);
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+* This function installs an HDMI callback function for the specified handler
+* type
+*
+* @param	InstancePtr is a pointer to the XVPhy instance.
+* @param	HandlerType is the interrupt handler type which specifies which
+*		interrupt event to attach the callback for.
+* @param	CallbackFunc is the address to the callback function.
+* @param	CallbackRef is the user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return	None.
+*
+* @note		None.
+*
+*******************************************************************************/
+void XVphy_SetHdmiCallback(XVphy *InstancePtr,
+		XVphy_HdmiHandlerType HandlerType,
+		void *CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid((HandlerType == XVPHY_HDMI_HANDLER_TXINIT) ||
+			(HandlerType == XVPHY_HDMI_HANDLER_TXREADY) ||
+			(HandlerType == XVPHY_HDMI_HANDLER_RXINIT) ||
+			(HandlerType == XVPHY_HDMI_HANDLER_RXREADY));
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	switch (HandlerType) {
+	case XVPHY_HDMI_HANDLER_TXINIT:
+		InstancePtr->HdmiTxInitCallback = (XVphy_Callback)CallbackFunc;
+		InstancePtr->HdmiTxInitRef = CallbackRef;
+		break;
+
+	case XVPHY_HDMI_HANDLER_TXREADY:
+		InstancePtr->HdmiTxReadyCallback = (XVphy_Callback)CallbackFunc;
+		InstancePtr->HdmiTxReadyRef = CallbackRef;
+		break;
+
+	case XVPHY_HDMI_HANDLER_RXINIT:
+		InstancePtr->HdmiRxInitCallback = (XVphy_Callback)CallbackFunc;
+		InstancePtr->HdmiRxInitRef = CallbackRef;
+		break;
+
+	case XVPHY_HDMI_HANDLER_RXREADY:
+		InstancePtr->HdmiRxReadyCallback = (XVphy_Callback)CallbackFunc;
+		InstancePtr->HdmiRxReadyRef = CallbackRef;
+		break;
+
+	default:
+		break;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function sets the appropriate HDMI interupt handlers.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiIntrHandlerCallbackInit(XVphy *InstancePtr)
+{
+	/* GT Interrupts */
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_QPLL_LOCK,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE,
+			(XVphy_IntrHandler)XVphy_HdmiGtHandler, InstancePtr);
+
+	/* Clock Detector Interrupts */
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE,
+			(XVphy_IntrHandler)XVphy_ClkDetHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE,
+			(XVphy_IntrHandler)XVphy_ClkDetHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT,
+			(XVphy_IntrHandler)XVphy_ClkDetHandler, InstancePtr);
+
+	XVphy_SetIntrHandler(InstancePtr,
+			XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT,
+			(XVphy_IntrHandler)XVphy_ClkDetHandler, InstancePtr);
+}
+
+#if (XPAR_VPHY_0_TRANSCEIVER != XVPHY_GTPE2)
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by QPLL lock done.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiQpllLockHandler(XVphy *InstancePtr)
+{
+	XVphy_PllType TxPllType;
+	XVphy_PllType RxPllType;
+	u8 Id, Id0, Id1;
+	XVphy_ChannelId ChId;
+
+	/* Determine PLL type. */
+	TxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+		XVPHY_CHANNEL_ID_CH1);
+	RxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+		XVPHY_CHANNEL_ID_CH1);
+
+	/* RX is using QPLL. */
+	if ((RxPllType == XVPHY_PLL_TYPE_QPLL) ||
+			(RxPllType == XVPHY_PLL_TYPE_QPLL0) ||
+			(RxPllType == XVPHY_PLL_TYPE_QPLL1) ||
+			(RxPllType == XVPHY_PLL_TYPE_PLL0)  ||
+			(RxPllType == XVPHY_PLL_TYPE_PLL1)) {
+
+		/* Determine which channel(s) to operate on. */
+		ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_RX, RxPllType);
+
+		if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+			/* Log, lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_QPLL_LOCK, 1);
+
+			/* GT RX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_RX, FALSE);
+
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0,
+					&Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					RxState = XVPHY_GT_STATE_RESET;
+			}
+
+			/* If the GT TX and RX are coupled, then update the GT
+			 * TX state as well. */
+			if (XVphy_IsBonded(InstancePtr, 0,
+						XVPHY_CHANNEL_ID_CH1)) {
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+				if (XVphy_MmcmLocked(InstancePtr, 0, XVPHY_DIR_TX)) {
+#endif
+				/* GT TX reset. */
+				XVphy_ResetGtTxRx(InstancePtr, 0,
+						XVPHY_CHANNEL_ID_CHA,
+						XVPHY_DIR_TX, TRUE);
+
+				XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+						&Id0, &Id1);
+				for (Id = Id0; Id <= Id1; Id++) {
+					InstancePtr->Quads[0].Plls[
+						XVPHY_CH2IDX(Id)].
+						TxState = XVPHY_GT_STATE_RESET;
+				}
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+				}
+#endif
+			}
+		}
+		else {
+			/* Log, Lost lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_QPLL_LOCK, 0);
+		}
+	}
+	/* TX is using QPLL. */
+	else {
+		/* Determine which channel(s) to operate on. */
+		ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_TX, TxPllType);
+
+		if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+			/* Log, lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_QPLL_LOCK, 1);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			if (XVphy_MmcmLocked(InstancePtr, 0, XVPHY_DIR_TX)) {
+#endif
+
+			/* GT TX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_TX, FALSE);
+
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0,
+					&Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					TxState = XVPHY_GT_STATE_RESET;
+			}
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			}
+#endif
+		}
+		else {
+			/* Log, Lost lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_QPLL_LOCK, 0);
+		}
+	}
+}
+#endif
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GTP PLL0/1 lock done.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiGtpPllLockHandler(XVphy *InstancePtr, u8 Pll)
+{
+	XVphy_PllType TxPllType;
+	XVphy_PllType RxPllType;
+	u8 Id, Id0, Id1;
+	XVphy_ChannelId ChId;
+
+	/* Determine PLL type. */
+	TxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+			XVPHY_CHANNEL_ID_CH1);
+	RxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+			XVPHY_CHANNEL_ID_CH1);
+
+	/* RX is using QPLL. */
+	if (((RxPllType == XVPHY_PLL_TYPE_PLL0) && (Pll == 0)) ||
+	    ((RxPllType == XVPHY_PLL_TYPE_PLL1) && (Pll == 1))) {
+
+		/* Determine which channel(s) to operate on. */
+		ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_RX, RxPllType);
+
+		if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+			/* Log, lock */
+			XVphy_LogWrite(InstancePtr, (Pll == 0) ?
+				XVPHY_LOG_EVT_PLL0_LOCK :
+				XVPHY_LOG_EVT_PLL1_LOCK, 1);
+
+			/* GT RX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_RX, FALSE);
+
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0,
+					&Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					RxState = XVPHY_GT_STATE_RESET;
+			}
+
+			/* If the GT TX and RX are coupled, then update the GT
+			 * TX state as well. */
+			if (XVphy_IsBonded(InstancePtr, 0,
+						XVPHY_CHANNEL_ID_CH1)) {
+				/* GT TX reset. */
+				XVphy_ResetGtTxRx(InstancePtr, 0,
+					XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_TX, TRUE);
+
+				XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+						&Id0, &Id1);
+				for (Id = Id0; Id <= Id1; Id++) {
+					InstancePtr->Quads[0].Plls[
+						XVPHY_CH2IDX(Id)].TxState =
+							XVPHY_GT_STATE_RESET;
+				}
+			}
+		}
+		else {
+			/* Log, Lost lock */
+			XVphy_LogWrite(InstancePtr, (Pll == 0) ?
+					XVPHY_LOG_EVT_PLL0_LOCK :
+					XVPHY_LOG_EVT_PLL1_LOCK, 0);
+		}
+	}
+	/* TX is using QPLL. */
+	else {
+		/* Determine which channel(s) to operate on. */
+		ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_TX, TxPllType);
+
+		if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+			/* Log, lock */
+			XVphy_LogWrite(InstancePtr, (Pll == 0) ?
+					XVPHY_LOG_EVT_PLL0_LOCK :
+					XVPHY_LOG_EVT_PLL1_LOCK, 1);
+
+			/* GT TX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_TX, FALSE);
+
+			XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0,
+					&Id1);
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					TxState = XVPHY_GT_STATE_RESET;
+			}
+		}
+		else {
+			/* Log, Lost lock */
+			XVphy_LogWrite(InstancePtr, (Pll == 0) ?
+					XVPHY_LOG_EVT_PLL0_LOCK :
+					XVPHY_LOG_EVT_PLL1_LOCK, 0);
+		}
+	}
+}
+#endif
+
+#if (XPAR_VPHY_0_TRANSCEIVER != XVPHY_GTPE2)
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by CPLL lock done.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiCpllLockHandler(XVphy *InstancePtr)
+{
+	XVphy_PllType TxPllType;
+	XVphy_PllType RxPllType;
+	u8 Id, Id0, Id1;
+	XVphy_ChannelId ChId;
+
+	/* Determine PLL type. */
+	TxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+			XVPHY_CHANNEL_ID_CH1);
+	RxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+			XVPHY_CHANNEL_ID_CH1);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+
+	/* RX is using CPLL. */
+	if (RxPllType == XVPHY_PLL_TYPE_CPLL) {
+		/* Determine which channel(s) to operate on. */
+		ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_RX, RxPllType);
+
+		if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+			/* Log, lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_CPLL_LOCK, 1);
+			/* GT RX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_RX, FALSE);
+
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					RxState = XVPHY_GT_STATE_RESET;
+			}
+
+			/* If the GT TX and RX are coupled, then update the GT
+			 * TX state as well. */
+			if (XVphy_IsBonded(InstancePtr, 0,
+						XVPHY_CHANNEL_ID_CH1)) {
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+				if (XVphy_MmcmLocked(InstancePtr, 0, XVPHY_DIR_TX)) {
+#endif
+				/* GT TX reset. */
+				XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+						XVPHY_DIR_TX, TRUE);
+
+				for (Id = Id0; Id <= Id1; Id++) {
+					InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+						TxState = XVPHY_GT_STATE_RESET;
+				}
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+				}
+#endif
+			}
+		}
+		else {
+			/* Log, Lost lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_CPLL_LOCK, 0);
+		}
+	}
+	/* TX is using CPLL. */
+	else {
+		/* Determine which channel(s) to operate on. */
+		ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_TX, TxPllType);
+
+		if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+			/* Log, lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_CPLL_LOCK, 1);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			if (XVphy_MmcmLocked(InstancePtr, 0, XVPHY_DIR_TX)) {
+#endif
+			/* GT TX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_TX, FALSE);
+
+			for (Id = Id0; Id <= Id1; Id++) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					TxState = XVPHY_GT_STATE_RESET;
+			}
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			}
+#endif
+		}
+		else {
+			/* Log, Lost lock */
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_CPLL_LOCK, 0);
+		}
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GT TX reset lock done.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiGtTxResetDoneLockHandler(XVphy *InstancePtr)
+{
+	u8 Id, Id0, Id1;
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_TX_RST_DONE, 0);
+
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE3) ||
+            (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE4) ||
+            (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTYE4)) {
+		XVphy_TxAlignReset(InstancePtr, XVPHY_CHANNEL_ID_CHA, TRUE);
+		XVphy_TxAlignReset(InstancePtr, XVPHY_CHANNEL_ID_CHA, FALSE);
+	}
+
+	/* GT alignment. */
+	XVphy_TxAlignStart(InstancePtr, XVPHY_CHANNEL_ID_CHA, TRUE);
+	XVphy_TxAlignStart(InstancePtr, XVPHY_CHANNEL_ID_CHA, FALSE);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+			InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].TxState =
+				XVPHY_GT_STATE_READY;
+
+			/* TX ready callback. */
+			if (InstancePtr->HdmiTxReadyCallback) {
+				InstancePtr->HdmiTxReadyCallback(
+						InstancePtr->HdmiTxReadyRef);
+			}
+		} else {
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			XVphy_ClkDetTimerLoad(InstancePtr, 0, XVPHY_DIR_TX,
+							InstancePtr->Config.AxiLiteClkFreq/100);
+#endif
+
+			InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].TxState =
+				XVPHY_GT_STATE_ALIGN;
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GT TX alignment done.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiGtTxAlignDoneLockHandler(XVphy *InstancePtr)
+{
+	u8 Id, Id0, Id1;
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_TX_ALIGN, 1);
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	/* Clear TX timer. */
+	XVphy_ClkDetTimerClear(InstancePtr, 0, XVPHY_DIR_TX);
+#endif
+
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].TxState =
+			XVPHY_GT_STATE_READY;
+	}
+
+	/* TX ready callback. */
+	if (InstancePtr->HdmiTxReadyCallback) {
+		InstancePtr->HdmiTxReadyCallback(InstancePtr->HdmiTxReadyRef);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by GT RX reset lock done.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiGtRxResetDoneLockHandler(XVphy *InstancePtr)
+{
+	u8 Id, Id0, Id1;
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_RX_RST_DONE, 0);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].RxState =
+			XVPHY_GT_STATE_READY;
+	}
+
+	/* If DRU is use/d, release its reset. */
+	if (InstancePtr->HdmiRxDruIsEnabled) {
+		XVphy_DruReset(InstancePtr, XVPHY_CHANNEL_ID_CHA, FALSE);
+	}
+
+	/* RX ready callback. */
+	if (InstancePtr->HdmiRxReadyCallback) {
+		InstancePtr->HdmiRxReadyCallback(InstancePtr->HdmiRxReadyRef);
+	}
+
+	/* If the GT TX and RX are coupled and DRU is inactive, then update
+     * the GT TX state as well. */
+	if (XVphy_IsBonded(InstancePtr, 0, XVPHY_CHANNEL_ID_CH1) &&
+			!InstancePtr->HdmiRxDruIsEnabled) {
+		/* GT TX reset. */
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, FALSE);
+
+		for (Id = Id0; Id <= Id1; Id++) {
+			InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].TxState =
+				XVPHY_GT_STATE_RESET;
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by a change in TX frequency
+* as detected by the HDMI clock detector logic.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiTxClkDetFreqChangeHandler(XVphy *InstancePtr)
+{
+	XVphy_PllType PllType;
+	u8 Id, Id0, Id1;
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	/* Ignore TX freq change when on bonded mode. */
+	if (XVphy_IsBonded(InstancePtr, 0, XVPHY_CHANNEL_ID_CH1)) {
+		return;
+	}
+#endif
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_TX_FREQ, 0);
+
+	/* Determine PLL type. */
+	PllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+			XVPHY_CHANNEL_ID_CH1);
+
+	/* Assert GT TX reset. */
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2)) {
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, TRUE);
+	}
+
+	/* If the TX frequency has changed, the PLL is always disabled. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_PowerDownGtPll(InstancePtr, 0,
+			(PllType == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_CHANNEL_ID_CHA : XVPHY_CHANNEL_ID_CMNA, TRUE);
+	}
+	XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA, XVPHY_DIR_TX,
+			TRUE);
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) {
+		XVphy_GtUserRdyEnable(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+		XVPHY_DIR_TX, FALSE);
+	}
+
+	/* Mask the MMCM Lock */
+	XVphy_MmcmLockedMaskEnable(InstancePtr, 0, XVPHY_DIR_TX, TRUE);
+
+	/* Disable TX MMCM. */
+	/* XVphy_MmcmPowerDown(InstancePtr, 0, XVPHY_DIR_TX, TRUE); */
+
+	/* Clear TX timer. */
+	XVphy_ClkDetTimerClear(InstancePtr, 0, XVPHY_DIR_TX);
+
+	/* Clear GT alignment. */
+	XVphy_TxAlignStart(InstancePtr, XVPHY_CHANNEL_ID_CHA, FALSE);
+
+	/* De-assert GT TX reset. */
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2)) {
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, FALSE);
+	}
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].TxState =
+			XVPHY_GT_STATE_IDLE;
+	}
+
+	/* If there is no reference clock, load TX timer in usec. */
+	if (XVphy_ClkDetGetRefClkFreqHz(InstancePtr, XVPHY_DIR_TX)) {
+		XVphy_ClkDetTimerLoad(InstancePtr, 0, XVPHY_DIR_TX,
+						InstancePtr->Config.AxiLiteClkFreq/1000);
+	}
+
+	/* Callback to re-initialize. */
+	if (InstancePtr->HdmiTxInitCallback) {
+		InstancePtr->HdmiTxInitCallback(InstancePtr->HdmiTxInitRef);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for events triggered by a change in RX frequency
+* as detected by the HDMI clock detector logic.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiRxClkDetFreqChangeHandler(XVphy *InstancePtr)
+{
+	XVphy_PllType PllType;
+	u32 RxRefClkHz;
+	u8 Id, Id0, Id1;
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_RX_FREQ, 0);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].RxState =
+			XVPHY_GT_STATE_IDLE;
+	}
+
+	/* Mask the MMCM Lock */
+	XVphy_MmcmLockedMaskEnable(InstancePtr, 0, XVPHY_DIR_RX, TRUE);
+
+	/* Determine PLL type and RX reference clock selection. */
+	PllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+			XVPHY_CHANNEL_ID_CH1);
+
+	/* Fetch New RX Reference Clock Frequency */
+	RxRefClkHz = XVphy_ClkDetGetRefClkFreqHz(InstancePtr, XVPHY_DIR_RX);
+
+	/* Round input frequency to 10 kHz. */
+	RxRefClkHz = (RxRefClkHz+5000) / 10000;
+	RxRefClkHz = RxRefClkHz * 10000;
+
+	/* Store RX reference clock. */
+	InstancePtr->HdmiRxRefClkHz = RxRefClkHz;
+
+	/* If the RX frequency has changed, the PLL is always disabled. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_PowerDownGtPll(InstancePtr, 0,
+			(PllType == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_CHANNEL_ID_CHA : XVPHY_CHANNEL_ID_CMNA, TRUE);
+	}
+
+	XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA, XVPHY_DIR_RX,
+			TRUE);
+
+	/* When the GT TX and RX are coupled, then disable the QPLL. */
+	if (XVphy_IsBonded(InstancePtr, 0, XVPHY_CHANNEL_ID_CH1)) {
+		/* Mask the MMCM Lock */
+		XVphy_MmcmLockedMaskEnable(InstancePtr, 0, XVPHY_DIR_TX, TRUE);
+		XVphy_PowerDownGtPll(InstancePtr, 0,
+			(PllType == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_CHANNEL_ID_CMNA : XVPHY_CHANNEL_ID_CHA, TRUE);
+		XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_TX, 1);
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, TRUE);
+	}
+
+	/* Assert GT RX reset */
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2)) {
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_RX, FALSE);
+	}
+
+	/* If DRU is present, disable it and assert reset. */
+	if (InstancePtr->Config.DruIsPresent) {
+		XVphy_DruReset(InstancePtr, XVPHY_CHANNEL_ID_CHA, TRUE);
+		XVphy_DruEnable(InstancePtr, XVPHY_CHANNEL_ID_CHA, FALSE);
+	}
+
+	/* Clear RX timer. */
+	XVphy_ClkDetTimerClear(InstancePtr, 0, XVPHY_DIR_RX);
+
+	/* If there is reference clock, load RX timer in usec.
+	 * The reference clock should be larger than 25Mhz. We are using a 20Mhz
+	 * instead to keep some margin for errors. */
+	if (RxRefClkHz > 20000000) {
+		XVphy_ClkDetTimerLoad(InstancePtr, 0, XVPHY_DIR_RX,
+						InstancePtr->Config.AxiLiteClkFreq/1000);
+
+		/* Callback to re-initialize. */
+		if (InstancePtr->HdmiRxInitCallback) {
+			InstancePtr->HdmiRxInitCallback(InstancePtr->HdmiRxInitRef);
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for TX timer timeout events.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiTxTimerTimeoutHandler(XVphy *InstancePtr)
+{
+	XVphy_ChannelId ChId;
+	XVphy_PllType PllType;
+	u8 Id, Id0, Id1;
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	/* Check if timer timed out while waiting for TX Alignment
+	 * If yes, reset the GT TX
+	 */
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	if (InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id0)].TxState ==
+			XVPHY_GT_STATE_ALIGN) {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_TX_ALIGN_TMOUT, 1);
+		/* GT TX reset. */
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, FALSE);
+
+		XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0,
+				&Id1);
+		for (Id = Id0; Id <= Id1; Id++) {
+			InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+				TxState = XVPHY_GT_STATE_RESET;
+		}
+		return;
+	}
+#endif
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_TX_TMR, 1);
+
+	/* Determine PLL type. */
+	PllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+			XVPHY_CHANNEL_ID_CH1);
+	/* Determine which channel(s) to operate on. */
+	ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_TX, PllType);
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	if (!XVphy_IsBonded(InstancePtr, 0, XVPHY_CHANNEL_ID_CH1)) {
+#endif
+	/* Start TX MMCM. */
+	XVphy_MmcmStart(InstancePtr, 0, XVPHY_DIR_TX);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	}
+#endif
+
+	/* Enable PLL. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_PowerDownGtPll(InstancePtr, 0,
+			(PllType == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_CHANNEL_ID_CHA : XVPHY_CHANNEL_ID_CMNA, FALSE);
+	}
+
+	if (PllType != XVPHY_PLL_TYPE_CPLL) {
+		/* Set QPLL Selection in PIO. */
+		XVphy_WriteCfgRefClkSelReg(InstancePtr, 0);
+	}
+
+	XVphy_ClkReconfig(InstancePtr, 0, ChId);
+	XVphy_OutDivReconfig(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_TX);
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE3) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE4) ||
+        (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTYE4)) {
+		XVphy_SetBufgGtDiv(InstancePtr, XVPHY_DIR_TX,
+			(PllType == XVPHY_PLL_TYPE_CPLL) ?
+			InstancePtr->Quads[0].Plls[0].TxOutDiv :
+			InstancePtr->Quads[0].Plls[0].TxOutDiv / 2);
+	}
+	XVphy_DirReconfig(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA, XVPHY_DIR_TX);
+
+	/* Assert PLL reset. */
+	XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_TX, TRUE);
+
+	/* Assert GT TX reset. */
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2)) {
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+							XVPHY_DIR_TX, TRUE);
+	}
+
+	/* De-assert PLL reset. */
+	XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_TX, FALSE);
+
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE3) ||
+	    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE4) ||
+        (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTYE4)) {
+		/* Clear GT alignment. */
+		XVphy_TxAlignStart(InstancePtr, ChId, FALSE);
+	}
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].TxState =
+			XVPHY_GT_STATE_LOCK;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for RX timer timeout events.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiRxTimerTimeoutHandler(XVphy *InstancePtr)
+{
+	XVphy_ChannelId ChId;
+	XVphy_PllType PllType;
+	u32 Status;
+	u8 Id, Id0, Id1;
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_RX_TMR, 1);
+
+	/* Determine PLL type. */
+	PllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+			XVPHY_CHANNEL_ID_CH1);
+	/* Determine which channel(s) to operate on. */
+	ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_RX, PllType);
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+
+	/* Set RX parameters. */
+	Status = XVphy_SetHdmiRxParam(InstancePtr, 0, ChId);
+	if (Status != XST_SUCCESS) {
+		for (Id = Id0; Id <= Id1; Id++) {
+			InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].RxState =
+				XVPHY_GT_STATE_IDLE;
+			if (XVphy_IsBonded(InstancePtr, 0,
+						XVPHY_CHANNEL_ID_CH1)) {
+				InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].
+					TxState = XVPHY_GT_STATE_IDLE;
+			}
+		}
+
+		return;
+	}
+
+	/* Enable PLL. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_PowerDownGtPll(InstancePtr, 0,
+			(PllType == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_CHANNEL_ID_CHA : XVPHY_CHANNEL_ID_CMNA, FALSE);
+	}
+
+	/* Enable DRU to set the clock muxes. */
+	XVphy_DruEnable(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+			InstancePtr->HdmiRxDruIsEnabled);
+
+	/* Update reference clock election. */
+	if (InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2) {
+		XVphy_CfgPllRefClkSel(InstancePtr, 0,
+			((PllType == XVPHY_PLL_TYPE_CPLL) ?
+				XVPHY_CHANNEL_ID_CHA : XVPHY_CHANNEL_ID_CMNA),
+			((InstancePtr->HdmiRxDruIsEnabled) ?
+				InstancePtr->Config.DruRefClkSel :
+				InstancePtr->Config.RxRefClkSel));
+	}
+	/* GTP */
+	else {
+		XVphy_CfgPllRefClkSel(InstancePtr, 0,
+			((PllType == XVPHY_PLL_TYPE_PLL0) ?
+				XVPHY_CHANNEL_ID_CMN0 : XVPHY_CHANNEL_ID_CMN1),
+			((InstancePtr->HdmiRxDruIsEnabled) ?
+				InstancePtr->Config.DruRefClkSel :
+				InstancePtr->Config.RxRefClkSel));
+	}
+
+	/* Update GT DRU mode. */
+	XVphy_HdmiGtDruModeEnable(InstancePtr, InstancePtr->HdmiRxDruIsEnabled);
+
+	/* Update RefClk selection. */
+	XVphy_WriteCfgRefClkSelReg(InstancePtr, 0);
+
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) {
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_RX, TRUE);
+        /* GTP Wizard locks the DRP access to its internal FSM during reset */
+		/* Wait for reset sequence to release DRP port. */
+		XVphy_WaitUs(InstancePtr, 5000);
+	}
+
+	/* Determine PLL type. */
+	PllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+			XVPHY_CHANNEL_ID_CH1);
+	/* Determine which channel(s) to operate on. */
+	ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_RX, PllType);
+
+	XVphy_ClkReconfig(InstancePtr, 0, ChId);
+	XVphy_OutDivReconfig(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_RX);
+	if (XVphy_IsBonded(InstancePtr, 0, XVPHY_CHANNEL_ID_CH1)) {
+		XVphy_OutDivReconfig(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX);
+	}
+
+	XVphy_DirReconfig(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA, XVPHY_DIR_RX);
+
+	/* Assert RX PLL reset. */
+	XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA, XVPHY_DIR_RX,
+			TRUE);
+
+	if (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTXE2) {
+		XVphy_ResetGtTxRx(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_RX, TRUE);
+	}
+
+	/* De-assert RX PLL reset. */
+	XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+			XVPHY_DIR_RX, FALSE);
+
+	/* When the TX and RX are coupled, clear GT alignment. */
+	if (XVphy_IsBonded(InstancePtr, 0, XVPHY_CHANNEL_ID_CH1)) {
+		if (InstancePtr->HdmiRxDruIsEnabled) {
+			XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_GT_UNBONDED, 1);
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_BONDED_DRU, 1);
+			XVphy_ErrorHandler(InstancePtr);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_PLL_LAYOUT, 1);
+			XVphy_PllLayoutErrorHandler(InstancePtr);
+#endif
+		}
+		else {
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_BONDED_DRU, 0);
+			XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_PLL_LAYOUT, 0);
+		}
+		XVphy_ResetGtPll(InstancePtr, 0, XVPHY_CHANNEL_ID_CHA,
+				XVPHY_DIR_TX, 0);
+		XVphy_TxAlignStart(InstancePtr, ChId, FALSE);
+	}
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[0].Plls[XVPHY_CH2IDX(Id)].RxState =
+			XVPHY_GT_STATE_LOCK;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for TX MMCM Lock events.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiTxMmcmLockHandler(XVphy *InstancePtr)
+{
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	XVphy_ChannelId ChId;
+	XVphy_PllType TxPllType;
+	u8 Id, Id0, Id1;
+#endif
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_TXPLL_LOCK, 1);
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+	/* Determine PLL type. */
+	TxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+		XVPHY_CHANNEL_ID_CH1);
+	/* Determine which channel(s) to operate on. */
+	ChId = XVphy_GetRcfgChId(InstancePtr, 0, XVPHY_DIR_TX, TxPllType);
+
+	/* Reset GT TX when associated PLL is Locked */
+	if (XVphy_IsPllLocked(InstancePtr, 0, ChId) == XST_SUCCESS) {
+
+		if (!XVphy_IsBonded(InstancePtr, 0,
+					XVPHY_CHANNEL_ID_CH1)) {
+			/* GT TX reset. */
+			XVphy_ResetGtTxRx(InstancePtr, 0,
+					XVPHY_CHANNEL_ID_CHA,
+					XVPHY_DIR_TX, FALSE);
+		}
+		XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA,
+				&Id0, &Id1);
+		for (Id = Id0; Id <= Id1; Id++) {
+			InstancePtr->Quads[0].Plls[
+				XVPHY_CH2IDX(Id)].
+				TxState = XVPHY_GT_STATE_RESET;
+		}
+	}
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function is the handler for RX MMCM Lock events.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiRxMmcmLockHandler(XVphy *InstancePtr)
+{
+
+	XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_RXPLL_LOCK, 1);
+
+}
+
+/*****************************************************************************/
+/**
+* This function is the interrupt handler for the GT events.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_HdmiGtHandler(XVphy *InstancePtr)
+{
+	u32 Event;
+	u32 EventMask;
+	u32 EventAck;
+	XVphy_GtState *TxStatePtr;
+	XVphy_GtState *RxStatePtr;
+
+	EventMask = XVPHY_INTR_QPLL0_LOCK_MASK | XVPHY_INTR_CPLL_LOCK_MASK |
+		XVPHY_INTR_QPLL1_LOCK_MASK | XVPHY_INTR_TXRESETDONE_MASK |
+		XVPHY_INTR_TXALIGNDONE_MASK | XVPHY_INTR_RXRESETDONE_MASK |
+		XVPHY_INTR_TXMMCMUSRCLK_LOCK_MASK | XVPHY_INTR_RXMMCMUSRCLK_LOCK_MASK;
+
+	u8 QuadId = 0;
+
+	/* Read Interrupt Status register */
+	Event = XVphy_ReadReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_STS_REG);
+
+	EventAck = EventMask & Event;
+
+	/* Read States for Quad=0 Ch1 */
+	TxStatePtr = &InstancePtr->Quads[QuadId].Ch1.TxState;
+	RxStatePtr = &InstancePtr->Quads[QuadId].Ch1.RxState;
+
+	if (Event & XVPHY_INTR_TXMMCMUSRCLK_LOCK_MASK) {
+		XVphy_HdmiTxMmcmLockHandler(InstancePtr);
+	}
+	if (Event & XVPHY_INTR_RXMMCMUSRCLK_LOCK_MASK) {
+		XVphy_HdmiRxMmcmLockHandler(InstancePtr);
+	}
+	if ((Event & XVPHY_INTR_QPLL0_LOCK_MASK) ||
+	    (Event & XVPHY_INTR_QPLL1_LOCK_MASK)) {
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTPE2)
+		if (Event & XVPHY_INTR_QPLL0_LOCK_MASK) { /* PLL0. */
+			XVphy_HdmiGtpPllLockHandler(InstancePtr, 0);
+		}
+		if (Event & XVPHY_INTR_QPLL1_LOCK_MASK) { /* PLL1. */
+			XVphy_HdmiGtpPllLockHandler(InstancePtr, 1);
+		}
+#else
+		XVphy_HdmiQpllLockHandler(InstancePtr);
+#endif
+	}
+#if (XPAR_VPHY_0_TRANSCEIVER != XVPHY_GTPE2)
+	if (Event & XVPHY_INTR_CPLL_LOCK_MASK) {
+		XVphy_HdmiCpllLockHandler(InstancePtr);
+	}
+#endif
+	if ((Event & XVPHY_INTR_TXRESETDONE_MASK)
+			&& (*TxStatePtr == XVPHY_GT_STATE_RESET)) {
+		XVphy_HdmiGtTxResetDoneLockHandler(InstancePtr);
+	}
+	if ((Event & XVPHY_INTR_TXALIGNDONE_MASK)
+			&& (*TxStatePtr == XVPHY_GT_STATE_ALIGN)) {
+		XVphy_HdmiGtTxAlignDoneLockHandler(InstancePtr);
+	}
+	if ((Event & XVPHY_INTR_RXRESETDONE_MASK)
+			&& (*RxStatePtr == XVPHY_GT_STATE_RESET)) {
+		XVphy_HdmiGtRxResetDoneLockHandler(InstancePtr);
+	}
+
+	/* Clear event flags by writing to Interrupt Status register */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_STS_REG,
+			EventAck);
+}
+
+/*****************************************************************************/
+/**
+* This function is the interrupt handler for the clock detector events.
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ClkDetHandler(XVphy *InstancePtr)
+{
+	u32 Event;
+	u32 EventMask;
+	u32 EventAck;
+
+	EventMask = XVPHY_INTR_TXCLKDETFREQCHANGE_MASK |
+				XVPHY_INTR_RXCLKDETFREQCHANGE_MASK |
+				XVPHY_INTR_TXTMRTIMEOUT_MASK |
+				XVPHY_INTR_RXTMRTIMEOUT_MASK;
+
+	/* Read Interrupt Status register */
+	Event = XVphy_ReadReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_STS_REG);
+
+	EventAck = EventMask & Event;
+
+	if (Event & XVPHY_INTR_TXCLKDETFREQCHANGE_MASK) {
+		XVphy_HdmiTxClkDetFreqChangeHandler(InstancePtr);
+	}
+	if (Event & XVPHY_INTR_RXCLKDETFREQCHANGE_MASK) {
+		XVphy_HdmiRxClkDetFreqChangeHandler(InstancePtr);
+	}
+	if (Event & XVPHY_INTR_TXTMRTIMEOUT_MASK) {
+		XVphy_HdmiTxTimerTimeoutHandler(InstancePtr);
+	}
+	if (Event & XVPHY_INTR_RXTMRTIMEOUT_MASK) {
+		XVphy_HdmiRxTimerTimeoutHandler(InstancePtr);
+	}
+
+	/* Clear event flags by writing to Interrupt Status register */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_STS_REG,
+			EventAck);
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_hw.h
@@ -0,0 +1,640 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_hw.h
+ *
+ * This header file contains the identifiers and low-level driver functions (or
+ * macros) that can be used to access the device. High-level driver functions
+ * are defined in xvphy.h.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Added GTPE2 and GTHE4 support
+ * 1.4   gm   29/11/16 Added ERR_IRQ register offset
+ * 1.5   gm   02/05/17 Added CPLL CAL reg and corresponding masks
+ * 1.6   gm   06/08/17 Added TX and RX MMCM lock Masks
+ * 1.7   gm   13/09/17 Added GTYE4 support
+ * </pre>
+ *
+ * @{
+*******************************************************************************/
+
+#ifndef XVPHY_HW_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XVPHY_HW_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files **********************************/
+
+#include "xil_io.h"
+#include "xil_types.h"
+
+/************************** Constant Definitions ******************************/
+
+/******************************************************************************/
+/**
+ * Address mapping for the Video PHY core.
+ *
+*******************************************************************************/
+/** @name VPHY core registers: General registers.
+  * @{
+  */
+#define XVPHY_VERSION_REG			0x000
+#define XVPHY_BANK_SELECT_REG		0x00C
+#define XVPHY_REF_CLK_SEL_REG		0x010
+#define XVPHY_PLL_RESET_REG			0x014
+#define XVPHY_PLL_LOCK_STATUS_REG	0x018
+#define XVPHY_TX_INIT_REG			0x01C
+#define XVPHY_TX_INIT_STATUS_REG	0x020
+#define XVPHY_RX_INIT_REG			0x024
+#define XVPHY_RX_INIT_STATUS_REG	0x028
+#define XVPHY_IBUFDS_GTXX_CTRL_REG	0x02C
+#define XVPHY_POWERDOWN_CONTROL_REG	0x030
+#define XVPHY_LOOPBACK_CONTROL_REG	0x038
+/* @} */
+
+/** @name VPHY core registers: Dynamic reconfiguration port (DRP) registers.
+  * @{
+  */
+#define XVPHY_DRP_CONTROL_CH1_REG	0x040
+#define XVPHY_DRP_CONTROL_CH2_REG	0x044
+#define XVPHY_DRP_CONTROL_CH3_REG	0x048
+#define XVPHY_DRP_CONTROL_CH4_REG	0x04C
+#define XVPHY_DRP_STATUS_CH1_REG	0x050
+#define XVPHY_DRP_STATUS_CH2_REG	0x054
+#define XVPHY_DRP_STATUS_CH3_REG	0x058
+#define XVPHY_DRP_STATUS_CH4_REG	0x05C
+#define XVPHY_DRP_CONTROL_COMMON_REG	0x060
+#define XVPHY_DRP_STATUS_COMMON_REG	0x064
+#define XVPHY_DRP_CONTROL_TXMMCM_REG	0x124
+#define XVPHY_DRP_STATUS_TXMMCM_REG	0x128
+#define XVPHY_DRP_CONTROL_RXMMCM_REG	0x144
+#define XVPHY_DRP_STATUS_RXMMCM_REG	0x148
+/* @} */
+
+/** @name VPHY core registers: CPLL Calibration registers.
+  * @{
+  */
+#define XVPHY_CPLL_CAL_PERIOD_REG	0x068
+#define XVPHY_CPLL_CAL_TOL_REG		0x06C
+/* @} */
+
+/** @name VPHY core registers: Transmitter function registers.
+  * @{
+  */
+#define XVPHY_TX_CONTROL_REG		0x070
+#define XVPHY_TX_BUFFER_BYPASS_REG	0x074
+#define XVPHY_TX_STATUS_REG			0x078
+#define XVPHY_TX_DRIVER_CH12_REG	0x07C
+#define XVPHY_TX_DRIVER_CH34_REG	0x080
+/* @} */
+
+/** @name VPHY core registers: Receiver function registers.
+  * @{
+  */
+#define XVPHY_RX_CONTROL_REG		0x100
+#define XVPHY_RX_STATUS_REG		    0x104
+#define XVPHY_RX_EQ_CDR_REG		    0x108
+#define XVPHY_RX_TDLOCK_REG		    0x10C
+/* @} */
+
+/** @name VPHY core registers: Interrupt registers.
+  * @{
+  */
+#define XVPHY_ERR_IRQ			0x03C
+#define XVPHY_INTR_EN_REG		0x110
+#define XVPHY_INTR_DIS_REG		0x114
+#define XVPHY_INTR_MASK_REG		0x118
+#define XVPHY_INTR_STS_REG		0x11C
+/* @} */
+
+/** @name User clocking registers: MMCM and BUFGGT registers.
+  * @{
+  */
+#define XVPHY_MMCM_TXUSRCLK_CTRL_REG	0x0120
+#define XVPHY_MMCM_TXUSRCLK_REG1	0x0124
+#define XVPHY_MMCM_TXUSRCLK_REG2	0x0128
+#define XVPHY_MMCM_TXUSRCLK_REG3	0x012C
+#define XVPHY_MMCM_TXUSRCLK_REG4	0x0130
+#define XVPHY_BUFGGT_TXUSRCLK_REG 	0x0134
+#define XVPHY_MISC_TXUSRCLK_REG		0x0138
+
+#define XVPHY_MMCM_RXUSRCLK_CTRL_REG	0x0140
+#define XVPHY_MMCM_RXUSRCLK_REG1	0x0144
+#define XVPHY_MMCM_RXUSRCLK_REG2	0x0148
+#define XVPHY_MMCM_RXUSRCLK_REG3	0x014C
+#define XVPHY_MMCM_RXUSRCLK_REG4	0x0150
+#define XVPHY_BUFGGT_RXUSRCLK_REG 	0x0154
+#define XVPHY_MISC_RXUSRCLK_REG		0x0158
+/* @} */
+
+/** @name Clock detector (HDMI) registers.
+  * @{
+  */
+#define XVPHY_CLKDET_CTRL_REG		0x0200
+#define XVPHY_CLKDET_STAT_REG		0x0204
+#define XVPHY_CLKDET_FREQ_TMR_TO_REG	0x0208
+#define XVPHY_CLKDET_FREQ_TX_REG	0x020C
+#define XVPHY_CLKDET_FREQ_RX_REG	0x0210
+#define XVPHY_CLKDET_TMR_TX_REG		0x0214
+#define XVPHY_CLKDET_TMR_RX_REG		0x0218
+#define XVPHY_CLKDET_FREQ_DRU_REG	0x021C
+/* @} */
+
+/** @name Data recovery unit registers (HDMI).
+  * @{
+  */
+#define XVPHY_DRU_CTRL_REG		0x0300
+#define XVPHY_DRU_STAT_REG		0x0304
+
+#define XVPHY_DRU_CFREQ_L_REG(Ch)	(0x0308 + (12 * (Ch - 1)))
+#define XVPHY_DRU_CFREQ_H_REG(Ch)	(0x030C + (12 * (Ch - 1)))
+#define XVPHY_DRU_GAIN_REG(Ch)		(0x0310 + (12 * (Ch - 1)))
+/* @} */
+
+/** @name TMDS Clock Pattern Generator registers (HDMI).
+  * @{
+  */
+#define XVPHY_PATGEN_CTRL_REG		0x0340
+/* @} */
+
+/******************************************************************************/
+
+/** @name VPHY core masks, shifts, and register values.
+  * @{
+  */
+/* 0x0F8: VERSION */
+#define XVPHY_VERSION_INTER_REV_MASK \
+				0x000000FF	/**< Internal revision. */
+#define XVPHY_VERSION_CORE_PATCH_MASK \
+				0x00000F00	/**< Core patch details. */
+#define XVPHY_VERSION_CORE_PATCH_SHIFT 8	/**< Shift bits for core patch
+							details. */
+#define XVPHY_VERSION_CORE_VER_REV_MASK \
+				0x0000F000	/**< Core version revision. */
+#define XVPHY_VERSION_CORE_VER_REV_SHIFT 12	/**< Shift bits for core version
+							revision. */
+#define XVPHY_VERSION_CORE_VER_MNR_MASK \
+				0x00FF0000	/**< Core minor version. */
+#define XVPHY_VERSION_CORE_VER_MNR_SHIFT 16	/**< Shift bits for core minor
+							version. */
+#define XVPHY_VERSION_CORE_VER_MJR_MASK \
+				0xFF000000	/**< Core major version. */
+#define XVPHY_VERSION_CORE_VER_MJR_SHIFT 24	/**< Shift bits for core major
+							version. */
+/* 0x00C: BANK_SELECT_REG */
+#define XVPHY_BANK_SELECT_TX_MASK	0x00F
+#define XVPHY_BANK_SELECT_RX_MASK	0xF00
+#define XVPHY_BANK_SELECT_RX_SHIFT	8
+/* 0x010: REF_CLK_SEL */
+#define XVPHY_REF_CLK_SEL_QPLL0_MASK	0x0000000F
+#define XVPHY_REF_CLK_SEL_CPLL_MASK	0x000000F0
+#define XVPHY_REF_CLK_SEL_CPLL_SHIFT	4
+#define XVPHY_REF_CLK_SEL_QPLL1_MASK	0x00000F00
+#define XVPHY_REF_CLK_SEL_QPLL1_SHIFT	8
+#define XVPHY_REF_CLK_SEL_XPLL_GTREFCLK0 1
+#define XVPHY_REF_CLK_SEL_XPLL_GTREFCLK1 2
+#define XVPHY_REF_CLK_SEL_XPLL_GTNORTHREFCLK0 3
+#define XVPHY_REF_CLK_SEL_XPLL_GTNORTHREFCLK1 4
+#define XVPHY_REF_CLK_SEL_XPLL_GTSOUTHREFCLK0 5
+#define XVPHY_REF_CLK_SEL_XPLL_GTSOUTHREFCLK1 6
+#define XVPHY_REF_CLK_SEL_XPLL_GTEASTREFCLK0 3
+#define XVPHY_REF_CLK_SEL_XPLL_GTEASTREFCLK1 4
+#define XVPHY_REF_CLK_SEL_XPLL_GTWESTREFCLK0 5
+#define XVPHY_REF_CLK_SEL_XPLL_GTWESTREFCLK1 6
+#define XVPHY_REF_CLK_SEL_XPLL_GTGREFCLK 7
+#define XVPHY_REF_CLK_SEL_SYSCLKSEL_MASK 0x0F000000
+#define XVPHY_REF_CLK_SEL_SYSCLKSEL_SHIFT 24
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL0 0
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_PLL1 1
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_CPLL 0
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL 1
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL0 3
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_DATA_QPLL1 2
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CH 0
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN 1
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN0 2
+#define XVPHY_REF_CLK_SEL_XXSYSCLKSEL_OUT_CMN1 3
+#define XVPHY_REF_CLK_SEL_RXSYSCLKSEL_OUT_MASK(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 0x03000000 : 0x02000000)
+#define XVPHY_REF_CLK_SEL_TXSYSCLKSEL_OUT_MASK(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 0x0C000000 : 0x08000000)
+#define XVPHY_REF_CLK_SEL_RXSYSCLKSEL_DATA_MASK(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 0x30000000 : 0x01000000)
+#define XVPHY_REF_CLK_SEL_TXSYSCLKSEL_DATA_MASK(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 0xC0000000 : 0x04000000)
+#define XVPHY_REF_CLK_SEL_RXSYSCLKSEL_OUT_SHIFT(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 24 : 25)
+#define XVPHY_REF_CLK_SEL_TXSYSCLKSEL_OUT_SHIFT(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 26 : 27)
+#define XVPHY_REF_CLK_SEL_RXSYSCLKSEL_DATA_SHIFT(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 28 : 24)
+#define XVPHY_REF_CLK_SEL_TXSYSCLKSEL_DATA_SHIFT(G) \
+	((((G) == XVPHY_GT_TYPE_GTHE3) || \
+        ((G) == XVPHY_GT_TYPE_GTHE4) || \
+		((G) == XVPHY_GT_TYPE_GTYE4)) ? 30 : 26)
+/* 0x014: PLL_RESET */
+#define XVPHY_PLL_RESET_CPLL_MASK	0x1
+#define XVPHY_PLL_RESET_QPLL0_MASK	0x2
+#define XVPHY_PLL_RESET_QPLL1_MASK	0x4
+/* 0x018: PLL_LOCK_STATUS */
+#define XVPHY_PLL_LOCK_STATUS_CPLL_MASK(Ch) \
+		(0x01 << (Ch - 1))
+#define XVPHY_PLL_LOCK_STATUS_QPLL0_MASK	0x10
+#define XVPHY_PLL_LOCK_STATUS_QPLL1_MASK	0x20
+#define XVPHY_PLL_LOCK_STATUS_CPLL_ALL_MASK \
+		(XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		 XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		 XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		 XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_PLL_LOCK_STATUS_CPLL_HDMI_MASK \
+		(XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		 XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		 XVPHY_PLL_LOCK_STATUS_CPLL_MASK(XVPHY_CHANNEL_ID_CH3))
+/* 0x01C, 0x024: TX_INIT, RX_INIT */
+#define XVPHY_TXRX_INIT_GTRESET_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_PMARESET_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_PCSRESET_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_TX_INIT_USERRDY_MASK(Ch) \
+		(0x08 << (8 * (Ch - 1)))
+#define XVPHY_RX_INIT_USERRDY_MASK(Ch) \
+		(0x40 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_PLLGTRESET_MASK(Ch) \
+		(0x80 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_GTRESET_ALL_MASK \
+		(XVPHY_TXRX_INIT_GTRESET_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		 XVPHY_TXRX_INIT_GTRESET_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		 XVPHY_TXRX_INIT_GTRESET_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		 XVPHY_TXRX_INIT_GTRESET_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_TX_INIT_USERRDY_ALL_MASK \
+		(XVPHY_TX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		 XVPHY_TX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		 XVPHY_TX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		 XVPHY_TX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_RX_INIT_USERRDY_ALL_MASK \
+		(XVPHY_RX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		 XVPHY_RX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		 XVPHY_RX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		 XVPHY_RX_INIT_USERRDY_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_TXRX_INIT_PLLGTRESET_ALL_MASK \
+		(XVPHY_TXRX_INIT_PLLGTRESET_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		 XVPHY_TXRX_INIT_PLLGTRESET_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		 XVPHY_TXRX_INIT_PLLGTRESET_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		 XVPHY_TXRX_INIT_PLLGTRESET_MASK(XVPHY_CHANNEL_ID_CH4))
+/* 0x020, 0x028: TX_STATUS, RX_STATUS */
+#define XVPHY_TXRX_INIT_STATUS_RESETDONE_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_STATUS_PMARESETDONE_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_STATUS_POWERGOOD_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_TXRX_INIT_STATUS_RESETDONE_ALL_MASK \
+	(XVPHY_TXRX_INIT_STATUS_RESETDONE_MASK(XVPHY_CHANNEL_ID_CH1) | \
+	 XVPHY_TXRX_INIT_STATUS_RESETDONE_MASK(XVPHY_CHANNEL_ID_CH2) | \
+	 XVPHY_TXRX_INIT_STATUS_RESETDONE_MASK(XVPHY_CHANNEL_ID_CH3) | \
+	 XVPHY_TXRX_INIT_STATUS_RESETDONE_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_TXRX_INIT_STATUS_PMARESETDONE_ALL_MASK \
+	(XVPHY_TXRX_INIT_STATUS_PMARESETDONE_MASK(XVPHY_CHANNEL_ID_CH1) | \
+	 XVPHY_TXRX_INIT_STATUS_PMARESETDONE_MASK(XVPHY_CHANNEL_ID_CH2) | \
+	 XVPHY_TXRX_INIT_STATUS_PMARESETDONE_MASK(XVPHY_CHANNEL_ID_CH3) | \
+	 XVPHY_TXRX_INIT_STATUS_PMARESETDONE_MASK(XVPHY_CHANNEL_ID_CH4))
+/* 0x02C: IBUFDS_GTXX_CTRL */
+#define XVPHY_IBUFDS_GTXX_CTRL_GTREFCLK0_CEB_MASK	0x1
+#define XVPHY_IBUFDS_GTXX_CTRL_GTREFCLK1_CEB_MASK	0x2
+/* 0x030: POWERDOWN_CONTROL */
+#define XVPHY_POWERDOWN_CONTROL_CPLLPD_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_POWERDOWN_CONTROL_QPLL0PD_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_POWERDOWN_CONTROL_QPLL1PD_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_POWERDOWN_CONTROL_RXPD_MASK(Ch) \
+		(0x18 << (8 * (Ch - 1)))
+#define XVPHY_POWERDOWN_CONTROL_RXPD_SHIFT(Ch) \
+		(3 + (8 * (Ch - 1)))
+#define XVPHY_POWERDOWN_CONTROL_TXPD_MASK(Ch) \
+		(0x60 << (8 * (Ch - 1)))
+#define XVPHY_POWERDOWN_CONTROL_TXPD_SHIFT(Ch) \
+		(5 + (8 * (Ch - 1)))
+/* 0x038: LOOPBACK_CONTROL */
+#define XVPHY_LOOPBACK_CONTROL_CH_MASK(Ch) \
+		(0x03 << (8 * (Ch - 1)))
+#define XVPHY_LOOPBACK_CONTROL_CH_SHIFT(Ch) \
+		(8 * (Ch - 1))
+/* 0x040, 0x044, 0x048, 0x04C, 0x060: DRP_CONTROL_CH[1-4], DRP_CONTROL_COMMON */
+#define XVPHY_DRP_CONTROL_DRPADDR_MASK	0x00000FFF
+#define XVPHY_DRP_CONTROL_DRPEN_MASK	0x00001000
+#define XVPHY_DRP_CONTROL_DRPWE_MASK	0x00002000
+#define XVPHY_DRP_CONTROL_DRPRESET_MASK	0x00004000
+#define XVPHY_DRP_CONTROL_DRPDI_MASK	0xFFFF0000
+#define XVPHY_DRP_CONTROL_DRPDI_SHIFT	16
+/* 0x050, 0x054, 0x058, 0x05C, 0x064: DRP_STATUS_CH[1-4], DRP_STATUS_COMMON */
+#define XVPHY_DRP_STATUS_DRPO_MASK	0x0FFFF
+#define XVPHY_DRP_STATUS_DRPRDY_MASK	0x10000
+#define XVPHY_DRP_STATUS_DRPBUSY_MASK	0x20000
+/* 0x068: CPLL CAL PERIOD */
+#define XVPHY_CPLL_CAL_PERIOD_MASK      0x3FFFF
+/* 0x06C: CPLL CAL TOLERANCE */
+#define XVPHY_CPLL_CAL_TOL_MASK         0x3FFFF
+/* 0x070: TX_CONTROL */
+#define XVPHY_TX_CONTROL_TX8B10BEN_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_TX_CONTROL_TX8B10BEN_ALL_MASK \
+		(XVPHY_TX_CONTROL_TX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_TX_CONTROL_TX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_TX_CONTROL_TX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_TX_CONTROL_TX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_TX_CONTROL_TXPOLARITY_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_TX_CONTROL_TXPOLARITY_ALL_MASK \
+		(XVPHY_TX_CONTROL_TXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_TX_CONTROL_TXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_TX_CONTROL_TXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_TX_CONTROL_TXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_TX_CONTROL_TXPRBSSEL_MASK(Ch) \
+		(0x5C << (8 * (Ch - 1)))
+#define XVPHY_TX_CONTROL_TXPRBSSEL_ALL_MASK \
+		(XVPHY_TX_CONTROL_TXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_TX_CONTROL_TXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_TX_CONTROL_TXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_TX_CONTROL_TXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_TX_CONTROL_TXPRBSSEL_SHIFT(Ch) \
+		(2 + (8 * (Ch - 1)))
+#define XVPHY_TX_CONTROL_TXPRBSFORCEERR_MASK(Ch) \
+		(0x20 << (8 * (Ch - 1)))
+#define XVPHY_TX_CONTROL_TXPRBSFORCEERR_ALL_MASK \
+		(XVPHY_TX_CONTROL_TXPRBSFORCEERR_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_TX_CONTROL_TXPRBSFORCEERR_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_TX_CONTROL_TXPRBSFORCEERR_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_TX_CONTROL_TXPRBSFORCEERR_MASK(XVPHY_CHANNEL_ID_CH4))
+/* 0x074: TX_BUFFER_BYPASS */
+#define XVPHY_TX_BUFFER_BYPASS_TXPHDLYRESET_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXPHALIGN_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXPHALIGNEN_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXPHDLYPD_MASK(Ch) \
+		(0x08 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXPHINIT_MASK(Ch) \
+		(0x10 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXDLYRESET_MASK(Ch) \
+		(0x20 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXDLYBYPASS_MASK(Ch) \
+		(0x40 << (8 * (Ch - 1)))
+#define XVPHY_TX_BUFFER_BYPASS_TXDLYEN_MASK(Ch) \
+		(0x80 << (8 * (Ch - 1)))
+/* 0x078: TX_STATUS */
+#define XVPHY_TX_STATUS_TXPHALIGNDONE_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_TX_STATUS_TXPHINITDONE_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_TX_STATUS_TXDLYRESETDONE_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_TX_STATUS_TXBUFSTATUS_MASK(Ch) \
+		(0x18 << (8 * (Ch - 1)))
+#define XVPHY_TX_STATUS_TXBUFSTATUS_SHIFT(Ch) \
+		(3 + (8 * (Ch - 1)))
+/* 0x07C, 0x080: TX_DRIVER_CH12, TX_DRIVER_CH34 */
+#define XVPHY_TX_DRIVER_TXDIFFCTRL_MASK(Ch) \
+		(0x000F << (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXDIFFCTRL_SHIFT(Ch) \
+		(16 * ((Ch - 1) % 2))
+#define XVPHY_TX_DRIVER_TXELECIDLE_MASK(Ch) \
+		(0x0010 << (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXELECIDLE_SHIFT(Ch) \
+		(4 + (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXINHIBIT_MASK(Ch) \
+		(0x0020 << (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXINHIBIT_SHIFT(Ch) \
+		(5 + (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXPOSTCURSOR_MASK(Ch) \
+		(0x07C0 << (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXPOSTCURSOR_SHIFT(Ch) \
+		(6 + (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXPRECURSOR_MASK(Ch) \
+		(0xF800 << (16 * ((Ch - 1) % 2)))
+#define XVPHY_TX_DRIVER_TXPRECURSOR_SHIFT(Ch) \
+		(11 + (16 * ((Ch - 1) % 2)))
+/* 0x100: RX_CONTROL */
+#define XVPHY_RX_CONTROL_RX8B10BEN_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_RX_CONTROL_RX8B10BEN_ALL_MASK \
+		(XVPHY_RX_CONTROL_RX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_RX_CONTROL_RX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_RX_CONTROL_RX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_RX_CONTROL_RX8B10BEN_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_RX_CONTROL_RXPOLARITY_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_RX_CONTROL_RXPOLARITY_ALL_MASK \
+		(XVPHY_RX_CONTROL_RXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_RX_CONTROL_RXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_RX_CONTROL_RXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_RX_CONTROL_RXPOLARITY_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_RX_CONTROL_RXPRBSCNTRESET_MASK(Ch) \
+		(0x08 << (8 * (Ch - 1)))
+#define XVPHY_RX_CONTROL_RXPRBSSEL_MASK(Ch) \
+		(0xF0 << (8 * (Ch - 1)))
+#define XVPHY_RX_CONTROL_RXPRBSSEL_ALL_MASK \
+		(XVPHY_RX_CONTROL_RXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_RX_CONTROL_RXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_RX_CONTROL_RXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_RX_CONTROL_RXPRBSSEL_MASK(XVPHY_CHANNEL_ID_CH4))
+#define XVPHY_RX_CONTROL_RXPRBSSEL_SHIFT(Ch) \
+		(4 + (8 * (Ch - 1)))
+/* 0x104: RX_STATUS */
+#define XVPHY_RX_STATUS_RXCDRLOCK_MASK(Ch) \
+		(0x1 << (8 * (Ch - 1)))
+#define XVPHY_RX_STATUS_RXBUFSTATUS_MASK(Ch) \
+		(0xE << (8 * (Ch - 1)))
+#define XVPHY_RX_STATUS_RXBUFSTATUS_SHIFT(Ch) \
+		(1 + (8 * (Ch - 1)))
+/* 0x104: RX_EQ_CDR */
+#define XVPHY_RX_CONTROL_RXLPMEN_MASK(Ch) \
+		(0x01 << (8 * (Ch - 1)))
+#define XVPHY_RX_STATUS_RXCDRHOLD_MASK(Ch) \
+		(0x02 << (8 * (Ch - 1)))
+#define XVPHY_RX_STATUS_RXOSOVRDEN_MASK(Ch) \
+		(0x04 << (8 * (Ch - 1)))
+#define XVPHY_RX_STATUS_RXLPMLFKLOVRDEN_MASK(Ch) \
+		(0x08 << (8 * (Ch - 1)))
+#define XVPHY_RX_STATUS_RXLPMHFOVRDEN_MASK(Ch) \
+		(0x10 << (8 * (Ch - 1)))
+#define XVPHY_RX_CONTROL_RXLPMEN_ALL_MASK \
+		(XVPHY_RX_CONTROL_RXLPMEN_MASK(XVPHY_CHANNEL_ID_CH1) | \
+		XVPHY_RX_CONTROL_RXLPMEN_MASK(XVPHY_CHANNEL_ID_CH2) | \
+		XVPHY_RX_CONTROL_RXLPMEN_MASK(XVPHY_CHANNEL_ID_CH3) | \
+		XVPHY_RX_CONTROL_RXLPMEN_MASK(XVPHY_CHANNEL_ID_CH4))
+/* 0x110, 0x114, 0x118, 0x11C: INTR_EN, INTR_DIS, INTR_MASK, INTR_STS */
+#define XVPHY_INTR_TXRESETDONE_MASK		0x00000001
+#define XVPHY_INTR_RXRESETDONE_MASK		0x00000002
+#define XVPHY_INTR_CPLL_LOCK_MASK		0x00000004
+#define XVPHY_INTR_QPLL0_LOCK_MASK		0x00000008
+#define XVPHY_INTR_TXALIGNDONE_MASK		0x00000010
+#define XVPHY_INTR_QPLL1_LOCK_MASK		0x00000020
+#define XVPHY_INTR_TXCLKDETFREQCHANGE_MASK	0x00000040
+#define XVPHY_INTR_RXCLKDETFREQCHANGE_MASK	0x00000080
+#define XVPHY_INTR_TXMMCMUSRCLK_LOCK_MASK	0x00000200
+#define XVPHY_INTR_RXMMCMUSRCLK_LOCK_MASK	0x00000400
+#define XVPHY_INTR_TXTMRTIMEOUT_MASK		0x40000000
+#define XVPHY_INTR_RXTMRTIMEOUT_MASK		0x80000000
+#define XVPHY_INTR_QPLL_LOCK_MASK		XVPHY_INTR_QPLL0_LOCK_MASK
+/* 0x120, 0x140: MMCM_TXUSRCLK_CTRL, MMCM_RXUSRCLK_CTRL */
+#define XVPHY_MMCM_USRCLK_CTRL_CFG_NEW_MASK	0x01
+#define XVPHY_MMCM_USRCLK_CTRL_RST_MASK		0x02
+#define XVPHY_MMCM_USRCLK_CTRL_CFG_SUCCESS_MASK	0x10
+#define XVPHY_MMCM_USRCLK_CTRL_LOCKED_MASK	0x200
+#define XVPHY_MMCM_USRCLK_CTRL_PWRDWN_MASK	0x400
+#define XVPHY_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK	0x800
+#define XVPHY_MMCM_USRCLK_CTRL_CLKINSEL_MASK	0x1000
+/* 0x124, 0x144: MMCM_TXUSRCLK_REG1, MMCM_RXUSRCLK_REG1 */
+#define XVPHY_MMCM_USRCLK_REG1_DIVCLK_MASK \
+					0x00000FF
+#define XVPHY_MMCM_USRCLK_REG1_CLKFBOUT_MULT_MASK \
+					0x000FF00
+#define XVPHY_MMCM_USRCLK_REG1_CLKFBOUT_MULT_SHIFT \
+					8
+#define XVPHY_MMCM_USRCLK_REG1_CLKFBOUT_FRAC_MASK \
+					0x3FF0000
+#define XVPHY_MMCM_USRCLK_REG1_CLKFBOUT_FRAC_SHIFT \
+					16
+/* 0x128, 0x148: MMCM_TXUSRCLK_REG2, MMCM_RXUSRCLK_REG2 */
+#define XVPHY_MMCM_USRCLK_REG2_DIVCLK_MASK \
+					0x00000FF
+#define XVPHY_MMCM_USRCLK_REG2_CLKOUT0_FRAC_MASK \
+					0x3FF0000
+#define XVPHY_MMCM_USRCLK_REG2_CLKOUT0_FRAC_SHIFT \
+					16
+/* 0x12C, 0x130, 0x14C, 0x150: MMCM_TXUSRCLK_REG[3,4], MMCM_RXUSRCLK_REG[3,4] */
+#define XVPHY_MMCM_USRCLK_REG34_DIVCLK_MASK \
+					0x00000FF
+/* 0x134, 0x154: BUFGT_TXUSRCLK, BUFGT_RXUSRCLK */
+#define XVPHY_BUFGGT_XXUSRCLK_CLR_MASK	0x1
+#define XVPHY_BUFGGT_XXUSRCLK_DIV_MASK	0xE
+#define XVPHY_BUFGGT_XXUSRCLK_DIV_SHIFT	1
+/* 0x138, 0x158: MISC_TXUSRCLK_REG, MISC_RXUSERCLK_REG */
+#define XVPHY_MISC_XXUSRCLK_CKOUT1_OEN_MASK	0x1
+#define XVPHY_MISC_XXUSRCLK_REFCLK_CEB_MASK	0x2
+/* 0x200: CLKDET_CTRL */
+#define XVPHY_CLKDET_CTRL_RUN_MASK			0x1
+#define XVPHY_CLKDET_CTRL_TX_TMR_CLR_MASK		0x2
+#define XVPHY_CLKDET_CTRL_RX_TMR_CLR_MASK		0x4
+#define XVPHY_CLKDET_CTRL_TX_FREQ_RST_MASK		0x8
+#define XVPHY_CLKDET_CTRL_RX_FREQ_RST_MASK		0x10
+#define XVPHY_CLKDET_CTRL_FREQ_LOCK_THRESH_MASK		0x1FE0
+#define XVPHY_CLKDET_CTRL_FREQ_LOCK_THRESH_SHIFT	5
+/* 0x204: CLKDET_STAT */
+#define XVPHY_CLKDET_STAT_TX_FREQ_ZERO_MASK		0x1
+#define XVPHY_CLKDET_STAT_RX_FREQ_ZERO_MASK		0x2
+#define XVPHY_CLKDET_STAT_TX_REFCLK_LOCK_MASK		0x3
+#define XVPHY_CLKDET_STAT_TX_REFCLK_LOCK_CAP_MASK	0x4
+/* 0x300: DRU_CTRL */
+#define XVPHY_DRU_CTRL_RST_MASK(Ch)	(0x01 << (8 * (Ch - 1)))
+#define XVPHY_DRU_CTRL_EN_MASK(Ch)	(0x02 << (8 * (Ch - 1)))
+/* 0x304: DRU_STAT */
+#define XVPHY_DRU_STAT_ACTIVE_MASK(Ch)	(0x01 << (8 * (Ch - 1)))
+#define XVPHY_DRU_STAT_VERSION_MASK	0xFF000000
+#define XVPHY_DRU_STAT_VERSION_SHIFT	24
+/* 0x30C, 0x318, 0x324, 0x330: DRU_CFREQ_H_CH[1-4] */
+#define XVPHY_DRU_CFREQ_H_MASK		0x1F
+/* 0x310, 0x31C, 0x328, 0x334: DRU_GAIN_CH[1-4] */
+#define XVPHY_DRU_GAIN_G1_MASK		0x00001F
+#define XVPHY_DRU_GAIN_G1_SHIFT		0
+#define XVPHY_DRU_GAIN_G1_P_MASK	0x001F00
+#define XVPHY_DRU_GAIN_G1_P_SHIFT	8
+#define XVPHY_DRU_GAIN_G2_MASK		0x1F0000
+#define XVPHY_DRU_GAIN_G2_SHIFT		16
+/* 0x340 TMDS PATGEN */
+#define XVPHY_PATGEN_CTRL_RATIO_MASK		0x7
+#define XVPHY_PATGEN_CTRL_RATIO_SHIFT		0
+/* @} */
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+/** @name Register access macro definitions.
+  * @{
+  */
+#define XVphy_In32 Xil_In32
+#define XVphy_Out32 Xil_Out32
+/* @} */
+
+/******************************************************************************/
+/**
+ * This is a low-level function that reads from the specified register.
+ *
+ * @param	BaseAddress is the base address of the device.
+ * @param	RegOffset is the register offset to be read from.
+ *
+ * @return	The 32-bit value of the specified register.
+ *
+ * @note	C-style signature:
+ *		u32 XVphy_ReadReg(u32 BaseAddress, u32 RegOffset)
+ *
+*******************************************************************************/
+#define XVphy_ReadReg(BaseAddress, RegOffset) \
+	XVphy_In32((BaseAddress) + (RegOffset))
+
+/******************************************************************************/
+/**
+ * This is a low-level function that writes to the specified register.
+ *
+ * @param	BaseAddress is the base address of the device.
+ * @param	RegOffset is the register offset to write to.
+ * @param	Data is the 32-bit data to write to the specified register.
+ *
+ * @return	None.
+ *
+ * @note	C-style signature:
+ *		void XVphy_WriteReg(u32 BaseAddress, u32 RegOffset, u32 Data)
+ *
+*******************************************************************************/
+#define XVphy_WriteReg(BaseAddress, RegOffset, Data) \
+	XVphy_Out32((BaseAddress) + (RegOffset), (Data))
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XVPHY_HW_H_ */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_i.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_i.c
@@ -0,0 +1,1510 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_i.c
+ *
+ * Contains generic APIs that are locally called or used within the
+ * VPHY driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm,  11/09/16 Initial release.
+ * 1.4   gm   29/11/16 Fixed c++ compiler warnings
+ *                     Added xcvr adaptor functions for C++ compilations
+ * 1.6   gm   06/08/17 Added XVphy_MmcmLocked, XVphy_ErrorHandler and
+ *                              XVphy_PllLayoutErrorHandler APIs
+ * 1.7   gm   13/09/17 Added GTYE4 support
+ * 1.8   gm   23/07/18 Moved APIs XVphy_SetTxVoltageSwing and
+ *                       XVphy_SetTxPreEmphasis to xvphy.c/h
+ *            05/09/18 Added XVphy_GetRefClkSourcesCount API
+ * 1.9   gm   11/04/18 Added XVphy_IsHDMI API
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include <linux/string.h>
+#include "xstatus.h"
+#include "xvphy.h"
+#include "xvphy_i.h"
+#include "xvphy_hdmi.h"
+#include <linux/delay.h>
+#include "xvphy_gt.h"
+
+/**************************** Function Prototypes *****************************/
+
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function writes the current software configuration for the reference
+* clock selections to hardware for the specified quad on all channels.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_WriteCfgRefClkSelReg(XVphy *InstancePtr, u8 QuadId)
+{
+	u32 RegVal = 0;
+	XVphy_Channel *ChPtr;
+	XVphy_GtType GtType = InstancePtr->Config.XcvrType;
+
+	/* Point to the first channel since settings apply to all channels. */
+	ChPtr = &InstancePtr->Quads[QuadId].Ch1;
+
+	/* PllRefClkSel. */
+	/* - QPLL0. */
+	RegVal &= ~XVPHY_REF_CLK_SEL_QPLL0_MASK;
+	RegVal = InstancePtr->Quads[QuadId].Cmn0.PllRefClkSel;
+	/* - CPLL. */
+	RegVal &= ~XVPHY_REF_CLK_SEL_CPLL_MASK;
+	RegVal |= (ChPtr->CpllRefClkSel << XVPHY_REF_CLK_SEL_CPLL_SHIFT);
+	if ((GtType == XVPHY_GT_TYPE_GTHE3) ||
+            (GtType == XVPHY_GT_TYPE_GTHE4) ||
+            (GtType == XVPHY_GT_TYPE_GTYE4) ||
+            (GtType == XVPHY_GT_TYPE_GTPE2)) {
+		/* - QPLL1. */
+		RegVal &= ~XVPHY_REF_CLK_SEL_QPLL1_MASK;
+		RegVal |= (InstancePtr->Quads[QuadId].Cmn1.PllRefClkSel <<
+				XVPHY_REF_CLK_SEL_QPLL1_SHIFT);
+	}
+
+	/* SysClkDataSel. PLLCLKSEL */
+	RegVal &= ~XVPHY_REF_CLK_SEL_SYSCLKSEL_MASK;
+	/* - TXSYSCLKSEL[0]. TXPLLCLKSEL*/
+	RegVal |= (ChPtr->TxDataRefClkSel <<
+		XVPHY_REF_CLK_SEL_TXSYSCLKSEL_DATA_SHIFT(GtType)) &
+		XVPHY_REF_CLK_SEL_TXSYSCLKSEL_DATA_MASK(GtType);
+	/* - RXSYSCLKSEL[0]. RXPLLCLKSEL*/
+	RegVal |= (ChPtr->RxDataRefClkSel <<
+		XVPHY_REF_CLK_SEL_RXSYSCLKSEL_DATA_SHIFT(GtType)) &
+		XVPHY_REF_CLK_SEL_RXSYSCLKSEL_DATA_MASK(GtType);
+
+	/* SysClkOutSel. */
+	/* - TXSYSCLKSEL[1]. */
+	RegVal |= (ChPtr->TxOutRefClkSel <<
+		XVPHY_REF_CLK_SEL_TXSYSCLKSEL_OUT_SHIFT(GtType)) &
+		XVPHY_REF_CLK_SEL_TXSYSCLKSEL_OUT_MASK(GtType);
+	/* - RXSYSCLKSEL[1]. */
+	RegVal |= (ChPtr->RxOutRefClkSel <<
+		XVPHY_REF_CLK_SEL_RXSYSCLKSEL_OUT_SHIFT(GtType)) &
+		XVPHY_REF_CLK_SEL_RXSYSCLKSEL_OUT_MASK(GtType);
+
+	/* Write to hardware. */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_REF_CLK_SEL_REG,
+			RegVal);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* Configure the PLL reference clock selection for the specified channel(s).
+* This is applied to both direction to the software configuration only.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	SysClkDataSel is the reference clock selection to configure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_CfgPllRefClkSel(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_PllRefClkSelType RefClkSel)
+{
+	u8 Id, Id0, Id1;
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].PllRefClkSel =
+					RefClkSel;
+	}
+}
+
+/*****************************************************************************/
+/**
+* Configure the SYSCLKDATA reference clock selection for the direction. Same
+* configuration applies to all channels in the quad. This is applied to the
+* software configuration only.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	SysClkDataSel is the reference clock selection to configure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_CfgSysClkDataSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_SysClkDataSelType SysClkDataSel)
+{
+	XVphy_Channel *ChPtr;
+	u8 Id, Id0, Id1;
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	/* Select in software - same for all channels. */
+	for (Id = Id0; Id <= Id1; Id++) {
+		ChPtr = &InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)];
+		ChPtr->DataRefClkSel[Dir] = SysClkDataSel;
+	}
+}
+
+/*****************************************************************************/
+/**
+* Configure the SYSCLKOUT reference clock selection for the direction. Same
+* configuration applies to all channels in the quad. This is applied to the
+* software configuration only.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	SysClkOutSel is the reference clock selection to configure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_CfgSysClkOutSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_SysClkOutSelType SysClkOutSel)
+{
+	XVphy_Channel *ChPtr;
+	u8 Id, Id0, Id1;
+
+	XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	/* Select in software - same for all channels. */
+	for (Id = Id0; Id <= Id1; Id++) {
+		ChPtr = &InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)];
+		ChPtr->OutRefClkSel[Dir] = SysClkOutSel;
+	}
+}
+
+/*****************************************************************************/
+/**
+* Obtain the reconfiguration channel ID for given PLL type
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	PllType is the PLL type being used by the channel.
+*
+* @return	The Channel ID to be used for reconfiguration
+*
+* @note		None.
+*
+******************************************************************************/
+XVphy_ChannelId XVphy_GetRcfgChId(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_PllType PllType)
+{
+	XVphy_ChannelId ChId;
+
+	/* Suppress Warning Messages */
+	InstancePtr = InstancePtr;
+	QuadId = QuadId;
+	Dir = Dir;
+
+	/* Determine which channel(s) to operate on. */
+	switch (PllType) {
+	case XVPHY_PLL_TYPE_QPLL:
+	case XVPHY_PLL_TYPE_QPLL0:
+	case XVPHY_PLL_TYPE_PLL0:
+		ChId = XVPHY_CHANNEL_ID_CMN0;
+		break;
+	case XVPHY_PLL_TYPE_QPLL1:
+	case XVPHY_PLL_TYPE_PLL1:
+		ChId = XVPHY_CHANNEL_ID_CMN1;
+		break;
+	default:
+		ChId = XVPHY_CHANNEL_ID_CHA;
+		break;
+	}
+
+	return ChId;
+}
+
+/*****************************************************************************/
+/**
+* Obtain the current reference clock frequency for the quad based on the
+* reference clock type.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	RefClkType is the type to obtain the clock selection for.
+*
+* @return	The current reference clock frequency for the quad for the
+*		specified type selection.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_GetQuadRefClkFreq(XVphy *InstancePtr, u8 QuadId,
+		XVphy_PllRefClkSelType RefClkType)
+{
+	u32 FreqHz;
+
+	u8 RefClkIndex = RefClkType - XVPHY_PLL_REFCLKSEL_TYPE_GTREFCLK0;
+
+	FreqHz = (RefClkType > XVPHY_PLL_REFCLKSEL_TYPE_GTGREFCLK) ? 0 :
+		InstancePtr->Quads[QuadId].RefClkHz[RefClkIndex];
+
+	return FreqHz;
+}
+
+/*****************************************************************************/
+/**
+* Obtain the current [RT]XSYSCLKSEL[0] configuration.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return	The current [RT]XSYSCLKSEL[0] selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XVphy_SysClkDataSelType XVphy_GetSysClkDataSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_ChannelId ChId)
+{
+	u32 Sel;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	ChId = ChId;
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+							XVPHY_REF_CLK_SEL_REG);
+
+	if (Dir == XVPHY_DIR_TX) {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XVPHY_REF_CLK_SEL_TXSYSCLKSEL_DATA_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XVPHY_REF_CLK_SEL_TXSYSCLKSEL_DATA_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+	else {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XVPHY_REF_CLK_SEL_RXSYSCLKSEL_DATA_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XVPHY_REF_CLK_SEL_RXSYSCLKSEL_DATA_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+
+	return (XVphy_SysClkDataSelType) Sel;
+}
+
+/*****************************************************************************/
+/**
+* Obtain the current [RT]XSYSCLKSEL[1] configuration.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return	The current [RT]XSYSCLKSEL[1] selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XVphy_SysClkOutSelType XVphy_GetSysClkOutSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_ChannelId ChId)
+{
+	u32 Sel;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+	ChId = ChId;
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_REF_CLK_SEL_REG);
+
+	if (Dir == XVPHY_DIR_TX) {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XVPHY_REF_CLK_SEL_TXSYSCLKSEL_OUT_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XVPHY_REF_CLK_SEL_TXSYSCLKSEL_OUT_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+	else {
+		/* Synchronize software configuration to hardware. */
+		Sel = RegVal & XVPHY_REF_CLK_SEL_RXSYSCLKSEL_OUT_MASK(
+				InstancePtr->Config.XcvrType);
+		Sel >>= XVPHY_REF_CLK_SEL_RXSYSCLKSEL_OUT_SHIFT(
+				InstancePtr->Config.XcvrType);
+	}
+
+	return (XVphy_SysClkOutSelType)Sel;
+}
+
+/*****************************************************************************/
+/**
+* This function will check the status of a PLL lock on the specified channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+*
+* @return
+*		- XST_SUCCESS if the specified PLL is locked.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_IsPllLocked(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	XVphy_PllType TxPllType;
+	XVphy_PllType RxPllType;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (ChId == XVPHY_CHANNEL_ID_CMN0) {
+		MaskVal = XVPHY_PLL_LOCK_STATUS_QPLL0_MASK;
+	}
+	else if (ChId == XVPHY_CHANNEL_ID_CMN1) {
+		MaskVal = XVPHY_PLL_LOCK_STATUS_QPLL1_MASK;
+	}
+	else if (ChId == XVPHY_CHANNEL_ID_CMNA) {
+		MaskVal = XVPHY_PLL_LOCK_STATUS_QPLL0_MASK |
+			  XVPHY_PLL_LOCK_STATUS_QPLL1_MASK;
+	}
+	else if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		TxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_TX,
+				XVPHY_CHANNEL_ID_CH1);
+		RxPllType = XVphy_GetPllType(InstancePtr, 0, XVPHY_DIR_RX,
+				XVPHY_CHANNEL_ID_CH1);
+		if (RxPllType == XVPHY_PLL_TYPE_CPLL &&
+				XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+			MaskVal = XVPHY_PLL_LOCK_STATUS_CPLL_HDMI_MASK;
+		}
+		else if (TxPllType == XVPHY_PLL_TYPE_CPLL &&
+				XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+			MaskVal = XVPHY_PLL_LOCK_STATUS_CPLL_HDMI_MASK;
+		}
+		else {
+			MaskVal = XVPHY_PLL_LOCK_STATUS_CPLL_ALL_MASK;
+		}
+	}
+	else {
+		MaskVal = XVPHY_PLL_LOCK_STATUS_CPLL_MASK(ChId);
+	}
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_PLL_LOCK_STATUS_REG);
+
+	if ((RegVal & MaskVal) == MaskVal) {
+		return XST_SUCCESS;
+	}
+
+	return XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+* This function will reset and enable the Video PHY's user core logic.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID which to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_GtUserRdyEnable(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Hold)
+{
+	u32 RegVal;
+	u32 MaskVal;
+	u32 RegOffset;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_TX_INIT_REG;
+
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal = XVPHY_TX_INIT_USERRDY_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_TX_INIT_USERRDY_MASK(ChId);
+		}
+	}
+	else {
+		RegOffset = XVPHY_RX_INIT_REG;
+		if (ChId == XVPHY_CHANNEL_ID_CHA) {
+			MaskVal = XVPHY_RX_INIT_USERRDY_ALL_MASK;
+		}
+		else {
+			MaskVal = XVPHY_RX_INIT_USERRDY_MASK(ChId);
+		}
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	/* Assert reset. */
+	RegVal |= MaskVal;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~MaskVal;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will reset the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the reset if set to 1.
+*		If set to 0: reset, then enable.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_MmcmReset(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir,
+		u8 Hold)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffsetCtrl = XVPHY_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XVPHY_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	/* Assert reset. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+	RegVal |= XVPHY_MMCM_USRCLK_CTRL_RST_MASK;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	if (!Hold) {
+		/* De-assert reset. */
+		RegVal &= ~XVPHY_MMCM_USRCLK_CTRL_RST_MASK;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl,
+									RegVal);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will reset the mixed-mode clock manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+* @param	Enable is an indicator whether to "Enable" the locked mask
+*		if set to 1. If set to 0: reset, then disable.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_MmcmLockedMaskEnable(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, u8 Enable)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffsetCtrl = XVPHY_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XVPHY_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	/* Assert reset. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl);
+	RegVal |= XVPHY_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl, RegVal);
+
+	if (!Enable) {
+		/* De-assert reset. */
+		RegVal &= ~XVPHY_MMCM_USRCLK_CTRL_LOCKED_MASK_MASK;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl,
+									RegVal);
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will get the lock status of the mixed-mode clock
+* manager (MMCM) core.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+
+*
+* @return	TRUE if Locked else FALSE.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XVphy_MmcmLocked(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir)
+{
+	u32 RegOffsetCtrl;
+	u32 RegVal;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffsetCtrl = XVPHY_MMCM_TXUSRCLK_CTRL_REG;
+	}
+	else {
+		RegOffsetCtrl = XVPHY_MMCM_RXUSRCLK_CTRL_REG;
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffsetCtrl) &
+				XVPHY_MMCM_USRCLK_CTRL_LOCKED_MASK;
+
+	return (RegVal ? TRUE : FALSE);
+
+}
+
+/*****************************************************************************/
+/**
+* This function obtains the divider value of the BUFG_GT peripheral.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Dir is an indicator for TX or RX
+* @param	Div 3-bit divider value
+*
+* @return	None.
+*
+******************************************************************************/
+void XVphy_SetBufgGtDiv(XVphy *InstancePtr, XVphy_DirectionType Dir, u8 Div)
+{
+	u32 RegVal;
+	u32 RegOffset;
+	u8 Divider = Div;
+
+	if (Divider == 0) {
+		Divider = 1;
+	}
+	else {
+		Divider = Divider - 1;
+	}
+
+
+	if (Dir == XVPHY_DIR_TX) {
+		RegOffset = XVPHY_BUFGGT_TXUSRCLK_REG;
+	}
+	else {
+		RegOffset = XVPHY_BUFGGT_RXUSRCLK_REG;
+	}
+
+	/* Read BUFG_GT register. */
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, RegOffset);
+	RegVal &= ~XVPHY_BUFGGT_XXUSRCLK_DIV_MASK;
+
+	/* Shift divider value to correct position. */
+	Divider <<= XVPHY_BUFGGT_XXUSRCLK_DIV_SHIFT;
+	Divider &= XVPHY_BUFGGT_XXUSRCLK_DIV_MASK;
+	RegVal |= Divider;
+
+	/* Write new value to BUFG_GT ctrl register. */
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, RegOffset, RegVal);
+}
+
+/*****************************************************************************/
+/**
+* This function will power down the specified GT PLL.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to power down the PLL for.
+* @param	Dir is an indicator for TX or RX.
+* @param	Hold is an indicator whether to "hold" the power down if set
+*		to 1. If set to 0: power down, then power back up.
+*
+* @return
+*		- XST_SUCCESS.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_PowerDownGtPll(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u8 Hold)
+{
+	u32 MaskVal = 0;
+	u32 RegVal;
+	u8 Id, Id0, Id1;
+
+	/* Suppress Warning Messages */
+	QuadId = QuadId;
+
+	if (XVPHY_ISCH(ChId)) {
+		XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	}
+	else {
+		/* When powering down a QPLL, power down for all channels. */
+		XVphy_Ch2Ids(InstancePtr, XVPHY_CHANNEL_ID_CHA, &Id0, &Id1);
+	}
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (ChId == XVPHY_CHANNEL_ID_CMN0) {
+			MaskVal |= XVPHY_POWERDOWN_CONTROL_QPLL0PD_MASK(Id);
+		}
+		else if (ChId == XVPHY_CHANNEL_ID_CMN1) {
+			MaskVal |= XVPHY_POWERDOWN_CONTROL_QPLL1PD_MASK(Id);
+		}
+		else if (ChId == XVPHY_CHANNEL_ID_CMNA) {
+			MaskVal |= XVPHY_POWERDOWN_CONTROL_QPLL0PD_MASK(Id) |
+				   XVPHY_POWERDOWN_CONTROL_QPLL1PD_MASK(Id);
+		}
+		else {
+			MaskVal |= XVPHY_POWERDOWN_CONTROL_CPLLPD_MASK(Id);
+		}
+	}
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+					XVPHY_POWERDOWN_CONTROL_REG);
+	RegVal |= MaskVal;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+					XVPHY_POWERDOWN_CONTROL_REG, RegVal);
+
+	if (!Hold) {
+		RegVal &= ~MaskVal;
+		XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+					XVPHY_POWERDOWN_CONTROL_REG, RegVal);
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function will try to find the necessary PLL divisor values to produce
+* the configured line rate given the specified PLL input frequency. This will
+* be done for all channels specified by ChId.
+* This function is a wrapper for XVphy_PllCalculator.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to calculate the PLL values for.
+* @param	ChId is the channel ID to calculate the PLL values for.
+* @param	Dir is an indicator for TX or RX.
+* @param	PllClkInFreqHz is the PLL input frequency on which to base the
+*		calculations on. A value of 0 indicates to use the currently
+*		configured quad PLL reference clock. A non-zero value indicates
+*		to ignore what is currently configured in SW, and use a custom
+*		frequency instead.
+*
+* @return
+*		- XST_SUCCESS if valid PLL values were found to satisfy the
+*		  constraints.
+*		- XST_FAILURE otherwise.
+*
+* @note		If successful, the channel's PllParams structure will be
+*		modified with the valid PLL parameters.
+*
+******************************************************************************/
+u32 XVphy_ClkCalcParams(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u32 PllClkInFreqHz)
+{
+	u32 Status = XST_SUCCESS;
+	u8 Id, Id0, Id1;
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		Status = XVphy_PllCalculator(InstancePtr, QuadId,
+					(XVphy_ChannelId)Id, Dir, PllClkInFreqHz);
+		if (Status != XST_SUCCESS) {
+			return Status;
+		}
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the current output divider configuration over DRP.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID for which to write the settings for.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_OutDivReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir)
+{
+	u32 Status;
+	u8 Id;
+	u8 Id0;
+	u8 Id1;
+
+	if (!XVPHY_ISCH(ChId)) {
+		ChId = XVPHY_CHANNEL_ID_CHA;
+	}
+
+	XVphy_LogWrite(InstancePtr, (Dir == XVPHY_DIR_TX) ?
+		XVPHY_LOG_EVT_GT_TX_RECONFIG : XVPHY_LOG_EVT_GT_RX_RECONFIG, 0);
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		Status = XVphy_OutDivChReconfig(InstancePtr, QuadId,
+					(XVphy_ChannelId)Id, Dir);
+		if (Status != XST_SUCCESS) {
+			break;
+		}
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the current RX/TX configuration over DRP.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID for which to write the settings for.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_DirReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir)
+{
+	u32 Status = XST_SUCCESS;
+	u8 Id, Id0, Id1;
+
+	if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE2) &&
+			(Dir == XVPHY_DIR_TX)) {
+		return XST_SUCCESS;
+	}
+
+    if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) &&
+		((InstancePtr->Config.TxProtocol == XVPHY_PROTOCOL_DP) ||
+		 (InstancePtr->Config.RxProtocol == XVPHY_PROTOCOL_DP))) {
+               ChId = XVPHY_CHANNEL_ID_CHA;
+    }
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (Dir == XVPHY_DIR_TX) {
+			Status |= XVphy_TxChReconfig(InstancePtr, QuadId,
+											(XVphy_ChannelId)Id);
+		}
+		else {
+			Status |= XVphy_RxChReconfig(InstancePtr, QuadId,
+											(XVphy_ChannelId)Id);
+		}
+		if (Status != XST_SUCCESS) {
+			Status = XST_FAILURE;
+			break;
+		}
+	}
+
+	XVphy_LogWrite(InstancePtr, (Dir == XVPHY_DIR_TX) ?
+		XVPHY_LOG_EVT_GT_TX_RECONFIG : XVPHY_LOG_EVT_GT_RX_RECONFIG, 1);
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the current clocking settings for each channel to
+* hardware based on the configuration stored in the driver's instance.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID for which to write the settings for.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ClkReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	u32 Status = XST_SUCCESS;
+	u8 Id;
+	u8 Id0;
+	u8 Id1;
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		if (XVPHY_ISCH(Id)) {
+			Status |= XVphy_ClkChReconfig(InstancePtr, QuadId,
+											(XVphy_ChannelId)Id);
+		}
+		else if (XVPHY_ISCMN(ChId)) {
+			if (((XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) ||
+				(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX))) &&
+			    (InstancePtr->HdmiIsQpllPresent == FALSE)) {
+				XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_NO_QPLL_ERR, 1);
+				XVphy_CfgErrIntr(InstancePtr, XVPHY_ERR_NO_QPLL, 1);
+				XVphy_ErrorHandler(InstancePtr);
+				Status = XST_FAILURE;
+				return Status;
+			}
+			Status |= XVphy_ClkCmnReconfig(InstancePtr, QuadId,
+											(XVphy_ChannelId)Id);
+		}
+		if (Status != XST_SUCCESS) {
+			Status = XST_FAILURE;
+			return Status;
+		}
+	}
+
+	if (XVPHY_ISCH(ChId)) {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_CPLL_RECONFIG, 1);
+	}
+	else if (XVPHY_ISCMN(ChId) &&
+			(InstancePtr->Config.XcvrType != XVPHY_GT_TYPE_GTPE2)) {
+		XVphy_LogWrite(InstancePtr, XVPHY_LOG_EVT_QPLL_RECONFIG, 1);
+	}
+	else if (XVPHY_ISCMN(ChId)) { /* GTPE2. */
+		XVphy_LogWrite(InstancePtr, (ChId == XVPHY_CHANNEL_ID_CMN0) ?
+			XVPHY_LOG_EVT_PLL0_RECONFIG :
+			XVPHY_LOG_EVT_PLL1_RECONFIG, 1);
+	}
+
+	return Status;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the channel IDs to correspond with the supplied
+* channel ID based on the protocol. HDMI uses 3 channels; DP uses 4. This ID
+* translation is done to allow other functions to operate iteratively over
+* multiple channels.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	ChId is the channel ID used to determine the indices.
+* @param	Id0 is a pointer to the start channel ID to set.
+* @param	Id1 is a pointer to the end channel ID to set.
+*
+* @return	None.
+*
+* @note		The contents of Id0 and Id1 will be set according to ChId.
+*
+******************************************************************************/
+void XVphy_Ch2Ids(XVphy *InstancePtr, XVphy_ChannelId ChId,
+		u8 *Id0, u8 *Id1)
+{
+	u8 Channels = 4;
+
+	if (ChId == XVPHY_CHANNEL_ID_CHA) {
+		*Id0 = XVPHY_CHANNEL_ID_CH1;
+		if ((XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) ||
+			(XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX))) {
+			if (InstancePtr->Config.UseGtAsTxTmdsClk == TRUE) {
+				*Id1 = XVPHY_CHANNEL_ID_CH4;
+			}
+			else {
+				*Id1 = XVPHY_CHANNEL_ID_CH3;
+			}
+		}
+		else {
+			Channels = ((InstancePtr->Config.TxChannels >=
+							InstancePtr->Config.RxChannels) ?
+									InstancePtr->Config.TxChannels :
+									InstancePtr->Config.RxChannels);
+
+			if (Channels == 1) {
+				*Id1 = XVPHY_CHANNEL_ID_CH1;
+			}
+			else if (Channels == 2) {
+				*Id1 = XVPHY_CHANNEL_ID_CH2;
+			}
+			else if (Channels == 3) {
+				*Id1 = XVPHY_CHANNEL_ID_CH3;
+			}
+			else {
+				*Id1 = XVPHY_CHANNEL_ID_CH4;
+			}
+		}
+	}
+	else if (ChId == XVPHY_CHANNEL_ID_CMNA) {
+		*Id0 = XVPHY_CHANNEL_ID_CMN0;
+		if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE3) ||
+		    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTHE4) ||
+		    (InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTYE4)) {
+			*Id1 = XVPHY_CHANNEL_ID_CMN1;
+		}
+		else {
+			*Id1 = XVPHY_CHANNEL_ID_CMN0;
+		}
+	}
+	else {
+		*Id0 = *Id1 = ChId;
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will translate from XVphy_PllType to XVphy_SysClkDataSelType.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	The reference clock type based on the PLL selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XVphy_SysClkDataSelType Pll2SysClkData(XVphy_PllType PllSelect)
+{
+	return	(PllSelect == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_SYSCLKSELDATA_TYPE_CPLL_OUTCLK :
+		(PllSelect == XVPHY_PLL_TYPE_QPLL) ?
+			XVPHY_SYSCLKSELDATA_TYPE_QPLL_OUTCLK :
+		(PllSelect == XVPHY_PLL_TYPE_QPLL0) ?
+			XVPHY_SYSCLKSELDATA_TYPE_QPLL0_OUTCLK :
+		(PllSelect == XVPHY_PLL_TYPE_QPLL1) ?
+			XVPHY_SYSCLKSELDATA_TYPE_QPLL1_OUTCLK :
+		(PllSelect == XVPHY_PLL_TYPE_PLL0) ?
+			XVPHY_SYSCLKSELDATA_TYPE_PLL0_OUTCLK :
+		XVPHY_SYSCLKSELDATA_TYPE_PLL1_OUTCLK;
+}
+
+/*****************************************************************************/
+/**
+* This function will translate from XVphy_PllType to XVphy_SysClkOutSelType.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	The reference clock type based on the PLL selection.
+*
+* @note		None.
+*
+******************************************************************************/
+XVphy_SysClkOutSelType Pll2SysClkOut(XVphy_PllType PllSelect)
+{
+	return	(PllSelect == XVPHY_PLL_TYPE_CPLL) ?
+			XVPHY_SYSCLKSELOUT_TYPE_CPLL_REFCLK :
+		(PllSelect == XVPHY_PLL_TYPE_QPLL) ?
+			XVPHY_SYSCLKSELOUT_TYPE_QPLL_REFCLK :
+		(PllSelect == XVPHY_PLL_TYPE_QPLL0) ?
+			XVPHY_SYSCLKSELOUT_TYPE_QPLL0_REFCLK :
+		(PllSelect == XVPHY_PLL_TYPE_QPLL1) ?
+			XVPHY_SYSCLKSELOUT_TYPE_QPLL1_REFCLK :
+		(PllSelect == XVPHY_PLL_TYPE_PLL0) ?
+			XVPHY_SYSCLKSELOUT_TYPE_PLL0_REFCLK :
+		XVPHY_SYSCLKSELOUT_TYPE_PLL1_REFCLK;
+}
+
+/*****************************************************************************/
+/**
+* This function will try to find the necessary PLL divisor values to produce
+* the configured line rate given the specified PLL input frequency.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to calculate the PLL values for.
+* @param	ChId is the channel ID to calculate the PLL values for.
+* @param	Dir is an indicator for TX or RX.
+* @param	PllClkInFreqHz is the PLL input frequency on which to base the
+*		calculations on. A value of 0 indicates to use the currently
+*		configured quad PLL reference clock. A non-zero value indicates
+*		to ignore what is currently configured in SW, and use a custom
+*		frequency instead.
+*
+* @return
+*		- XST_SUCCESS if valid PLL values were found to satisfy the
+*		  constraints.
+*		- XST_FAILURE otherwise.
+*
+* @note		If successful, the channel's PllParams structure will be
+*		modified with the valid PLL parameters.
+*
+******************************************************************************/
+u32 XVphy_PllCalculator(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir,
+		u32 PllClkInFreqHz)
+{
+	u32 Status;
+	u64 PllClkOutFreqHz;
+	u64 CalcLineRateFreqHz;
+	u8 Id, Id0, Id1;
+	u64 PllClkInFreqHzIn = PllClkInFreqHz;
+	XVphy_Channel *PllPtr = &InstancePtr->Quads[QuadId].
+		Plls[XVPHY_CH2IDX(ChId)];
+
+	if (!PllClkInFreqHzIn) {
+		PllClkInFreqHzIn = XVphy_GetQuadRefClkFreq(InstancePtr, QuadId,
+					PllPtr->PllRefClkSel);
+	}
+
+	/* Select PLL value table offsets. */
+	const XVphy_GtPllDivs *GtPllDivs;
+	if (XVPHY_ISCH(ChId)) {
+		GtPllDivs = &InstancePtr->GtAdaptor->CpllDivs;
+	}
+	else {
+		GtPllDivs = &InstancePtr->GtAdaptor->QpllDivs;
+	}
+
+	const u8 *M, *N1, *N2, *D;
+	for (N2 = GtPllDivs->N2; *N2 != 0; N2++) {
+	for (N1 = GtPllDivs->N1; *N1 != 0; N1++) {
+	for (M = GtPllDivs->M;   *M != 0;  M++) {
+		PllClkOutFreqHz = (PllClkInFreqHzIn * *N1 * *N2) / *M;
+
+		/* Test if the calculated PLL clock is in the VCO range. */
+		Status = XVphy_CheckPllOpRange(InstancePtr, QuadId, ChId,
+				PllClkOutFreqHz);
+		if (Status != XST_SUCCESS) {
+			continue;
+		}
+
+		if ((InstancePtr->Config.XcvrType == XVPHY_GT_TYPE_GTPE2) ||
+				(XVPHY_ISCH(ChId))) {
+			PllClkOutFreqHz *= 2;
+		}
+		/* Apply TX/RX divisor. */
+		for (D = GtPllDivs->D; *D != 0; D++) {
+			CalcLineRateFreqHz = PllClkOutFreqHz / *D;
+			if (CalcLineRateFreqHz == PllPtr->LineRateHz) {
+				goto calc_done;
+			}
+		}
+	}
+	}
+	}
+	/* Calculation failed, don't change divisor settings. */
+	return XST_FAILURE;
+
+calc_done:
+	/* Found the multiplier and divisor values for requested line rate. */
+	PllPtr->PllParams.MRefClkDiv = *M;
+	PllPtr->PllParams.NFbDiv = *N1;
+	PllPtr->PllParams.N2FbDiv = *N2; /* Won't be used for QPLL.*/
+	PllPtr->PllParams.IsLowerBand = 1; /* Won't be used for CPLL. */
+
+	if (XVPHY_ISCMN(ChId)) {
+		/* Same divisor value for all channels if using a QPLL. */
+		ChId = XVPHY_CHANNEL_ID_CHA;
+	}
+
+	XVphy_Ch2Ids(InstancePtr, ChId, &Id0, &Id1);
+	for (Id = Id0; Id <= Id1; Id++) {
+		InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(Id)].OutDiv[Dir] =
+			*D;
+		if (Dir == XVPHY_DIR_RX) {
+			XVphy_CfgSetCdr(InstancePtr, QuadId, (XVphy_ChannelId)Id);
+		}
+	}
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+* This function calculates the PLL VCO operating frequency.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return	PLL VCO frequency in Hz
+*
+* @note		None.
+*
+******************************************************************************/
+u64 XVphy_GetPllVcoFreqHz(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir)
+{
+	u64 PllxVcoRateHz;
+	u64 PllRefClkHz;
+	XVphy_Channel *PllPtr = &InstancePtr->Quads[QuadId].
+                    Plls[XVPHY_CH2IDX(ChId)];
+
+	if (Dir == XVPHY_DIR_TX) {
+		if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_TX)) {
+			PllRefClkHz = InstancePtr->HdmiTxRefClkHz;
+		}
+		else {
+			PllRefClkHz = XVphy_GetQuadRefClkFreq(InstancePtr, QuadId,
+									PllPtr->PllRefClkSel);
+		}
+	}
+	else {
+		if (XVphy_IsHDMI(InstancePtr, XVPHY_DIR_RX)) {
+#if defined (XPAR_XV_HDMITX_0_DEVICE_ID) || defined (XPAR_XV_HDMIRX_0_DEVICE_ID)
+			if (InstancePtr->HdmiRxDruIsEnabled) {
+				PllRefClkHz = XVphy_DruGetRefClkFreqHz(InstancePtr);
+			}
+			else {
+				PllRefClkHz = InstancePtr->HdmiRxRefClkHz;
+			}
+#else
+			PllRefClkHz = 0;
+#endif
+		}
+		else {
+			PllRefClkHz = XVphy_GetQuadRefClkFreq(InstancePtr, QuadId,
+									PllPtr->PllRefClkSel);
+		}
+	}
+
+	PllxVcoRateHz = (u64)(PllRefClkHz *
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+								PllParams.N1FbDiv *
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+								PllParams.N2FbDiv) /
+				InstancePtr->Quads[QuadId].Plls[XVPHY_CH2IDX(ChId)].
+								PllParams.MRefClkDiv;
+
+	return PllxVcoRateHz;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the number of active reference clock sources
+* based in the CFG
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	No of active REFCLK sources
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XVphy_GetRefClkSourcesCount(XVphy *InstancePtr)
+{
+	u8 RefClkNum = 0;
+	u8 RefClkNumMax = 3;
+	XVphy_PllRefClkSelType RefClkSel[RefClkNumMax];
+	XVphy_PllRefClkSelType RefClkSelTemp[RefClkNumMax];
+	u8 i, j, Match;
+
+	/* TxRefClkSel */
+	RefClkSel[0] = (InstancePtr->Config.TxProtocol != XVPHY_PROTOCOL_NONE) ?
+						InstancePtr->Config.TxRefClkSel : 99;
+	/* RxRefClkSel */
+	RefClkSel[1] = (InstancePtr->Config.RxProtocol != XVPHY_PROTOCOL_NONE) ?
+						InstancePtr->Config.RxRefClkSel : 99;
+	/* DruRefClkSel */
+	RefClkSel[2] = (InstancePtr->Config.DruIsPresent) ?
+						InstancePtr->Config.DruRefClkSel : 99;
+
+	/* Initialize Unique RefClk holder */
+	for (i=0; i<RefClkNumMax; i++) {
+		RefClkSelTemp[i] = 99;
+	}
+
+	i = 0;
+	do {
+		if (RefClkSel[i] != 99) {
+			Match = 0;
+			j = 0;
+			/* Check if RefClkSel is already in Unique Holder array */
+			do {
+				if (RefClkSelTemp[j] == RefClkSel[i]) {
+					Match |= 1;
+				}
+				j++;
+			} while (j<RefClkNum);
+
+			/* Register in Unique Holder if new RefClk is detected */
+			if (Match == 0) {
+				RefClkSelTemp[RefClkNum] = RefClkSel[i];
+				/* Increment RefClk counter */
+				RefClkNum++;
+			}
+		}
+		i++;
+	} while (i<RefClkNumMax);
+
+	return RefClkNum;
+}
+
+#ifdef __cplusplus
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to set the clock and data recovery
+* (CDR) values for a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_CfgSetCdr(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->CfgSetCdr(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to check if a given PLL output
+* frequency is within the operating range of the PLL for the GT type.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	PllClkOutFreqHz is the frequency to check.
+*
+* @return
+*		- XST_SUCCESS if the frequency resides within the PLL's range.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_CheckPllOpRange(XVphy *InstancePtr, u8 QuadId,
+							XVphy_ChannelId ChId, u64 PllClkOutFreqHz)
+{
+	return InstancePtr->GtAdaptor->CheckPllOpRange(InstancePtr, QuadId, ChId,
+							PllClkOutFreqHz);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to set the output divider logic for
+* a given channel.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_OutDivChReconfig(XVphy *InstancePtr, u8 QuadId,
+							XVphy_ChannelId ChId, XVphy_DirectionType Dir)
+{
+	return InstancePtr->GtAdaptor->OutDivChReconfig(InstancePtr, QuadId,
+							ChId, Dir);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the channel
+* clock settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ClkChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->ClkChReconfig(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the common channel
+* clock settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	CmnId is the common channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_ClkCmnReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->ClkCmnReconfig(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the channel's
+* RX settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_RxChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->RxChReconfig(InstancePtr, QuadId, ChId);
+}
+
+/*****************************************************************************/
+/**
+* This function is a transceiver adaptor to configure the channel's
+* TX settings.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	ChId is the channel ID to operate on.
+*
+* @return
+*		- XST_SUCCESS if the configuration was successful.
+*		- XST_FAILURE otherwise.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_TxChReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId)
+{
+	return InstancePtr->GtAdaptor->TxChReconfig(InstancePtr, QuadId, ChId);
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function checks if Instance is HDMI 2.0 or HDMI 2.1
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+* @param	Dir is an indicator for RX or TX.
+*
+* @return	TRUE if HDMI 2.0 or 2.1 else FALSE.
+*
+* @note		None.
+*
+******************************************************************************/
+u8 XVphy_IsHDMI(XVphy *InstancePtr, XVphy_DirectionType Dir)
+{
+	if (Dir == XVPHY_DIR_TX) {
+		if (InstancePtr->Config.TxProtocol == XVPHY_PROTOCOL_HDMI) {
+			return TRUE;
+		}
+	} else { /* Dir == XVPHY_DIR_RX */
+		if (InstancePtr->Config.RxProtocol == XVPHY_PROTOCOL_HDMI) {
+			return TRUE;
+		}
+	}
+
+	return FALSE;
+}
+
+/*****************************************************************************/
+/**
+* This function is the error condition handler
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+* @param    ErrIrqType is the error type
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_ErrorHandler(XVphy *InstancePtr)
+{
+	if (InstancePtr->ErrorCallback != NULL) {
+		InstancePtr->ErrorCallback(InstancePtr->ErrorRef);
+	}
+}
+
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+/*****************************************************************************/
+/**
+* This function is the error condition handler
+*
+* @param	InstancePtr is a pointer to the VPHY instance.
+* @param    ErrIrqType is the error type
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_PllLayoutErrorHandler(XVphy *InstancePtr)
+{
+	if (InstancePtr->PllLayoutErrorCallback != NULL) {
+		InstancePtr->PllLayoutErrorCallback(InstancePtr->PllLayoutErrorRef);
+	}
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_i.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_i.h
@@ -0,0 +1,151 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_i.h
+ *
+ * Contains generic APIs that are locally called or used within the
+ * VPHY driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   gm   11/09/16 Initial release.
+ * 1.4   gm   11/24/16 Made debug log optional (can be disabled via makefile)
+ * 1.5   gm   02/05/17 Added XVphy_CfgCpllCalPeriodandTol API for US+ devices
+ * 1.6   gm   06/08/17 Added XVphy_MmcmLocked, XVphy_ErrorHandler and
+ *                       XVphy_PllLayoutErrorHandler APIs
+ * 1.7   gm   13/09/17 Removed XVphy_MmcmWriteParameters API
+ * 1.8   gm   23/07/18 Moved APIs XVphy_SetTxVoltageSwing and
+ *                       XVphy_SetTxPreEmphasis to xvphy.c/h
+ *            05/09/18 Added XVphy_GetRefClkSourcesCount API
+ * 1.9   gm   11/04/18 Added XVphy_IsHDMI API
+ *                           Moved XVphy_SetRxLpm to xvphy.c/.h
+ * </pre>
+ *
+ * @{
+*******************************************************************************/
+
+#ifndef XVPHY_I_H_
+/* Prevent circular inclusions by using protection macros. */
+#define XVPHY_I_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/******************************* Include Files ********************************/
+
+#include "xil_assert.h"
+#include "xvphy.h"
+#include "xvphy_hw.h"
+#include "xvidc.h"
+
+/****************************** Type Definitions ******************************/
+
+
+/**************************** Function Prototypes *****************************/
+
+
+void XVphy_Ch2Ids(XVphy *InstancePtr, XVphy_ChannelId ChId,
+		u8 *Id0, u8 *Id1);
+XVphy_SysClkDataSelType Pll2SysClkData(XVphy_PllType PllSelect);
+XVphy_SysClkOutSelType Pll2SysClkOut(XVphy_PllType PllSelect);
+u32 XVphy_PllCalculator(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir,
+		u32 PllClkInFreqHz);
+
+/* xvphy.c: Channel configuration functions - setters. */
+u32 XVphy_WriteCfgRefClkSelReg(XVphy *InstancePtr, u8 QuadId);
+void XVphy_CfgPllRefClkSel(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_PllRefClkSelType RefClkSel);
+void XVphy_CfgSysClkDataSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_SysClkDataSelType SysClkDataSel);
+void XVphy_CfgSysClkOutSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_SysClkOutSelType SysClkOutSel);
+
+u32 XVphy_ClkCalcParams(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u32 PllClkInFreqHz);
+u32 XVphy_OutDivReconfig(XVphy *InstancePtr, u8 QuadId,
+				XVphy_ChannelId ChId, XVphy_DirectionType Dir);
+u32 XVphy_DirReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir);
+u32 XVphy_ClkReconfig(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+
+/* xvphy.c: Channel configuration functions - getters. */
+XVphy_ChannelId XVphy_GetRcfgChId(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_PllType PllType);
+u32 XVphy_GetQuadRefClkFreq(XVphy *InstancePtr, u8 QuadId,
+		XVphy_PllRefClkSelType RefClkType);
+XVphy_SysClkDataSelType XVphy_GetSysClkDataSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_ChannelId ChId);
+XVphy_SysClkOutSelType XVphy_GetSysClkOutSel(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, XVphy_ChannelId ChId);
+u32 XVphy_IsPllLocked(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId);
+u32 XVphy_GtUserRdyEnable(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		XVphy_DirectionType Dir, u8 Hold);
+u32 XVphy_CfgCpllCalPeriodandTol(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir, u32 FreeRunClkFreq);
+
+
+/* xvphy.c: GT/MMCM DRP access. */
+u32 XVphy_MmcmWriteParameters(XVphy *InstancePtr, u8 QuadId,
+							XVphy_DirectionType Dir);
+void XVphy_MmcmReset(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir,
+		u8 Hold);
+void XVphy_MmcmLockedMaskEnable(XVphy *InstancePtr, u8 QuadId,
+		XVphy_DirectionType Dir, u8 Enable);
+u8 XVphy_MmcmLocked(XVphy *InstancePtr, u8 QuadId, XVphy_DirectionType Dir);
+void XVphy_SetBufgGtDiv(XVphy *InstancePtr, XVphy_DirectionType Dir, u8 Div);
+/* xvphy.c Miscellaneous control. */
+u32 XVphy_PowerDownGtPll(XVphy *InstancePtr, u8 QuadId, XVphy_ChannelId ChId,
+		u8 Hold);
+
+/* xvphy_intr.c: Interrupt handling functions. */
+void XVphy_SetIntrHandler(XVphy *InstancePtr, XVphy_IntrHandlerType HandlerType,
+		XVphy_IntrHandler CallbackFunc, void *CallbackRef);
+void XVphy_IntrEnable(XVphy *InstancePtr, XVphy_IntrHandlerType Intr);
+void XVphy_IntrDisable(XVphy *InstancePtr, XVphy_IntrHandlerType Intr);
+void XVphy_CfgErrIntr(XVphy *InstancePtr, XVphy_ErrType ErrIrq, u8 Set);
+
+u64 XVphy_GetPllVcoFreqHz(XVphy *InstancePtr, u8 QuadId,
+		XVphy_ChannelId ChId, XVphy_DirectionType Dir);
+u8 XVphy_GetRefClkSourcesCount(XVphy *InstancePtr);
+
+u8 XVphy_IsHDMI(XVphy *InstancePtr, XVphy_DirectionType Dir);
+void XVphy_HdmiTxTimerTimeoutHandler(XVphy *InstancePtr);
+void XVphy_HdmiRxTimerTimeoutHandler(XVphy *InstancePtr);
+
+void XVphy_ErrorHandler(XVphy *InstancePtr);
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTXE2)
+void XVphy_PllLayoutErrorHandler(XVphy *InstancePtr);
+#endif
+
+/******************* Macros (Inline Functions) Definitions ********************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* XVPHY_I_H_ */
+/** @} */
\ No newline at end of file
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_intr.c
@@ -0,0 +1,293 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_intr.c
+ *
+ * This file contains functions related to XVphy interrupt handling.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  10/19/15 Initial release.
+ * 1.4   gm   29/11/16 Added XVphy_CfgErrIntr for ERR_IRQ impl
+ * 1.6   gm   06/08/17 Added TX and RX MMCM locked handlers
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xvphy.h"
+#include "xvphy_i.h"
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function enables interrupts associated with the specified interrupt type
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ * @param	Intr is the interrupt type/mask to enable.
+ *
+ * @return	None.
+ *
+ * @note	None.
+*
+*******************************************************************************/
+void XVphy_IntrEnable(XVphy *InstancePtr, XVphy_IntrHandlerType Intr)
+{
+	u32 RegVal;
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_EN_REG);
+	RegVal |= Intr;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_EN_REG, RegVal);
+}
+
+/******************************************************************************/
+/**
+ * This function disabled interrupts associated with the specified interrupt
+ * type.
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ * @param	Intr is the interrupt type/mask to disable.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVphy_IntrDisable(XVphy *InstancePtr, XVphy_IntrHandlerType Intr)
+{
+	u32 RegVal;
+
+	RegVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_INTR_DIS_REG);
+	RegVal |= Intr;
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr, XVPHY_INTR_DIS_REG,
+			RegVal);
+}
+
+/******************************************************************************/
+/**
+ * This function installs a callback function for the specified handler type.
+ *
+ * @param	InstancePtr is a pointer to the XVPhy instance.
+ * @param	HandlerType is the interrupt handler type which specifies which
+ *		interrupt event to attach the callback for.
+ * @param	CallbackFunc is the address to the callback function.
+ * @param	CallbackRef is the user data item that will be passed to the
+ *		callback function when it is invoked.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVphy_SetIntrHandler(XVphy *InstancePtr, XVphy_IntrHandlerType HandlerType,
+			XVphy_IntrHandler CallbackFunc, void *CallbackRef)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid((HandlerType == XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_QPLL_LOCK) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK) ||
+		(HandlerType ==
+			XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE) ||
+		(HandlerType ==
+			XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT) ||
+		(HandlerType == XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT));
+	Xil_AssertVoid(CallbackFunc != NULL);
+	Xil_AssertVoid(CallbackRef != NULL);
+
+	switch (HandlerType) {
+	case XVPHY_INTR_HANDLER_TYPE_TXRESET_DONE:
+		InstancePtr->IntrTxResetDoneHandler = CallbackFunc;
+		InstancePtr->IntrTxResetDoneCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_RXRESET_DONE:
+		InstancePtr->IntrRxResetDoneHandler = CallbackFunc;
+		InstancePtr->IntrRxResetDoneCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_CPLL_LOCK:
+		InstancePtr->IntrCpllLockHandler = CallbackFunc;
+		InstancePtr->IntrCpllLockCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_QPLL_LOCK:
+		InstancePtr->IntrQpllLockHandler = CallbackFunc;
+		InstancePtr->IntrQpllLockCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_TXALIGN_DONE:
+		InstancePtr->IntrTxAlignDoneHandler = CallbackFunc;
+		InstancePtr->IntrTxAlignDoneCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_QPLL1_LOCK:
+		InstancePtr->IntrQpll1LockHandler = CallbackFunc;
+		InstancePtr->IntrQpll1LockCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_TX_CLKDET_FREQ_CHANGE:
+		InstancePtr->IntrTxClkDetFreqChangeHandler =
+							CallbackFunc;
+		InstancePtr->IntrTxClkDetFreqChangeCallbackRef =
+							CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_RX_CLKDET_FREQ_CHANGE:
+		InstancePtr->IntrRxClkDetFreqChangeHandler =
+							CallbackFunc;
+		InstancePtr->IntrRxClkDetFreqChangeCallbackRef =
+							CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_TX_MMCM_LOCK_CHANGE:
+		InstancePtr->IntrTxMmcmLockHandler = CallbackFunc;
+		InstancePtr->IntrTxMmcmLockCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_RX_MMCM_LOCK_CHANGE:
+		InstancePtr->IntrRxMmcmLockHandler = CallbackFunc;
+		InstancePtr->IntrRxMmcmLockCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_TX_TMR_TIMEOUT:
+		InstancePtr->IntrTxTmrTimeoutHandler = CallbackFunc;
+		InstancePtr->IntrTxTmrTimeoutCallbackRef = CallbackRef;
+		break;
+	case XVPHY_INTR_HANDLER_TYPE_RX_TMR_TIMEOUT:
+		InstancePtr->IntrRxTmrTimeoutHandler = CallbackFunc;
+		InstancePtr->IntrRxTmrTimeoutCallbackRef = CallbackRef;
+		break;
+	default:
+		break;
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function is the interrupt handler for the XVphy driver. It will detect
+ * what kind of interrupt has happened, and will invoke the appropriate callback
+ * function.
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVphy_InterruptHandler(XVphy *InstancePtr)
+{
+	u32 IntrStatus;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Determine what kind of interrupts have occurred. */
+	IntrStatus = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_INTR_STS_REG);
+
+	if (IntrStatus & XVPHY_INTR_CPLL_LOCK_MASK) {
+		InstancePtr->IntrCpllLockHandler(
+				InstancePtr->IntrCpllLockCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_QPLL_LOCK_MASK) {
+		InstancePtr->IntrQpllLockHandler(
+				InstancePtr->IntrQpllLockCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_QPLL1_LOCK_MASK) {
+		InstancePtr->IntrQpll1LockHandler(
+				InstancePtr->IntrQpll1LockCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_TXRESETDONE_MASK) {
+		InstancePtr->IntrTxResetDoneHandler(
+				InstancePtr->IntrTxResetDoneCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_TXALIGNDONE_MASK) {
+		InstancePtr->IntrTxAlignDoneHandler(
+				InstancePtr->IntrTxAlignDoneCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_RXRESETDONE_MASK) {
+		InstancePtr->IntrRxResetDoneHandler(
+				InstancePtr->IntrRxResetDoneCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_TXCLKDETFREQCHANGE_MASK) {
+		InstancePtr->IntrTxClkDetFreqChangeHandler(
+				InstancePtr->IntrTxClkDetFreqChangeCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_RXCLKDETFREQCHANGE_MASK) {
+		InstancePtr->IntrRxClkDetFreqChangeHandler(
+				InstancePtr->IntrRxClkDetFreqChangeCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_TXMMCMUSRCLK_LOCK_MASK) {
+		InstancePtr->IntrTxMmcmLockHandler(
+				InstancePtr->IntrTxMmcmLockCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_RXMMCMUSRCLK_LOCK_MASK) {
+		InstancePtr->IntrRxMmcmLockHandler(
+				InstancePtr->IntrRxMmcmLockCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_TXTMRTIMEOUT_MASK) {
+		InstancePtr->IntrTxTmrTimeoutHandler(
+				InstancePtr->IntrTxTmrTimeoutCallbackRef);
+	}
+	if (IntrStatus & XVPHY_INTR_RXTMRTIMEOUT_MASK) {
+		InstancePtr->IntrRxTmrTimeoutHandler(
+				InstancePtr->IntrRxTmrTimeoutCallbackRef);
+	}
+}
+
+/******************************************************************************/
+/**
+ * This function configures the error IRQ register based on the condition
+ * to generate an ERR_IRQ event
+ *
+ * @param	InstancePtr is a pointer to the XVphy instance.
+ *          ErrIrq is the IRQ type as define in XVphy_ErrType
+ *          Set is the flag to set or clear the ErrIrq param
+ *
+ * @return	None.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+void XVphy_CfgErrIntr(XVphy *InstancePtr, XVphy_ErrType ErrIrq, u8 Set)
+{
+	u32 ErrIrqVal;
+	u32 WriteVal;
+
+	ErrIrqVal = XVphy_ReadReg(InstancePtr->Config.BaseAddr,
+			XVPHY_ERR_IRQ);
+
+	WriteVal = (u32)ErrIrq;
+
+	if (Set) {
+		ErrIrqVal |= WriteVal;
+	}
+	else {
+		ErrIrqVal &= ~WriteVal;
+	}
+
+	XVphy_WriteReg(InstancePtr->Config.BaseAddr,
+				XVPHY_ERR_IRQ, ErrIrqVal);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_log.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_log.c
@@ -0,0 +1,586 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy.c
+ *
+ * Contains a minimal set of functions for the XVphy driver that allow access
+ * to all of the Video PHY core's functionality. See xvphy.h for a detailed
+ * description of the driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  10/19/15 Initial release.
+ * 1.1   gm   02/01/16 Additional events for event log printout
+ * 1.2   gm            Added log events for debugging
+ * 1.4   gm   11/24/16 Made debug log optional (can be disabled via makefile)
+ *                     Added XVPHY_LOG_EVT_TX_ALIGN_TMOUT log event
+ * 1.6   gm   06/08/17 Added XVPHY_LOG_EVT_HDMI20_ERR log event
+ *                     Added Red & Yellow printing for errors and warnings
+ *                     Added XVPHY_LOG_EVT_NO_QPLL_ERR log event
+ *                     Changed xil_printf new lines to \r\n
+ *                     Added XVPHY_LOG_EVT_DRU_CLK_ERR log event
+ * 1.7   gm   13/09/17 Added XVPHY_LOG_EVT_USRCLK_ERR event
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xvphy.h"
+#include "xvphy_i.h"
+
+/************************** Constant Definitions *****************************/
+#define ANSI_COLOR_RED     "\x1b[31m"
+#define ANSI_COLOR_GREEN   "\x1b[32m"
+#define ANSI_COLOR_YELLOW  "\x1b[33m"
+#define ANSI_COLOR_BLUE    "\x1b[34m"
+#define ANSI_COLOR_MAGENTA "\x1b[35m"
+#define ANSI_COLOR_CYAN    "\x1b[36m"
+#define ANSI_COLOR_WHITE   "\x1b[37m"
+#define ANSI_COLOR_RESET   "\x1b[0m"
+
+
+/**************************** Function Prototypes *****************************/
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function will reset the driver's logginc mechanism.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_LogReset(XVphy *InstancePtr)
+{
+#ifdef XV_VPHY_LOG_ENABLE
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Log.HeadIndex = 0;
+	InstancePtr->Log.TailIndex = 0;
+#endif
+}
+
+#ifdef XV_VPHY_LOG_ENABLE
+/*****************************************************************************/
+/**
+* This function will insert an event in the driver's logginc mechanism.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	Evt is the event type to log.
+* @param	Data is the associated data for the event.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVphy_LogWrite(XVphy *InstancePtr, XVphy_LogEvent Evt, u8 Data)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Evt <= (XVPHY_LOG_EVT_DUMMY));
+	Xil_AssertVoid(Data < 0xFF);
+
+	/* Write data and event into log buffer */
+	InstancePtr->Log.DataBuffer[InstancePtr->Log.HeadIndex] =
+			(Data << 8) | Evt;
+
+	/* Update head pointer if reached to end of the buffer */
+	if (InstancePtr->Log.HeadIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) / 2) - 1)) {
+		/* Clear pointer */
+		InstancePtr->Log.HeadIndex = 0;
+	}
+	else {
+		/* Increment pointer */
+		InstancePtr->Log.HeadIndex++;
+	}
+
+	/* Check tail pointer. When the two pointer are equal, then the buffer
+	 * is full. In this case then increment the tail pointer as well to
+	 * remove the oldest entry from the buffer. */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) / 2) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will read the last event from the log.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+*
+* @return	The log data.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_LogRead(XVphy *InstancePtr)
+{
+#ifdef XV_VPHY_LOG_ENABLE
+	u16 Log;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if there is any data in the log */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		Log = 0;
+	}
+	else {
+		Log = InstancePtr->Log.DataBuffer[InstancePtr->Log.TailIndex];
+
+		/* Increment tail pointer */
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) / 2) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+
+	return Log;
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function will print the entire log to the passed buffer.
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	buff Buffer to print to
+* @param	buff_size size off buff passed
+*
+* @return	number of bytes written to buff.
+*
+* @note		None.
+*
+******************************************************************************/
+int XVphy_LogShow(XVphy *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+#ifdef XV_VPHY_LOG_ENABLE
+	u16 Log;
+	u8 Evt;
+	u8 Data;
+
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	strSize = scnprintf(buff, buff_size,
+			"\r\n\n\nVPHY log\r\n" \
+			"------\r\n");
+
+	/* Read log data */
+	Log = XVphy_LogRead(InstancePtr);
+
+	while (Log != 0 && (buff_size - strSize) > 30 ) {
+		/* Event */
+		Evt = Log & 0xff;
+
+		/* Data */
+		Data = (Log >> 8) & 0xFF;
+
+		switch (Evt) {
+		case (XVPHY_LOG_EVT_NONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"GT log end\r\n-------\r\n");
+			break;
+		case (XVPHY_LOG_EVT_QPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL enable (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_QPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"QPLL reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_CPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"CPLL enable (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_CPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"CPLL reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_TXPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX MMCM enable (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_TXPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"TX MMCM reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_RXPLL_EN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX MMCM enable (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_RXPLL_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"RX MMCM reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_GTRX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"GT RX reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_GTTX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"GT TX reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_VID_TX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Video TX reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_VID_RX_RST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Video RX reset (%0d)\r\n", Data);
+			break;
+		case (XVPHY_LOG_EVT_TX_ALIGN):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX alignment done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX alignment start.\r\n.");
+			}
+			break;
+		case (XVPHY_LOG_EVT_TX_ALIGN_TMOUT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX alignment watchdog timed out.\r\n");
+			break;
+		case (XVPHY_LOG_EVT_TX_TMR):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX timer event\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX timer load\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_RX_TMR):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX timer event\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX timer load\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_CPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_GT_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_GT_TX_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT TX reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT TX reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_GT_RX_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT RX reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT RX reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_QPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_PLL0_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL0 reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL0 reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_PLL1_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL1 reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL1 reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_INIT):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT init done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"GT init start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_TXPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_RXPLL_RECONFIG):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM reconfig done\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM reconfig start\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_QPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"QPLL lost lock\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_PLL0_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL0 lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL0 lost lock\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_PLL1_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL1 lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"PLL1 lost lock\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_CPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"CPLL lost lock\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_RXPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX MMCM lost lock\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_TXPLL_LOCK):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM lock\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"TX MMCM lost lock\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_TX_RST_DONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX reset done\r\n");
+			break;
+		case (XVPHY_LOG_EVT_RX_RST_DONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX reset done\r\n");
+			break;
+		case (XVPHY_LOG_EVT_TX_FREQ):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX frequency event\r\n");
+			break;
+		case (XVPHY_LOG_EVT_RX_FREQ):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX frequency event\r\n");
+			break;
+		case (XVPHY_LOG_EVT_DRU_EN):
+			if (Data == 1) {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX DRU enable\r\n");
+			}
+			else {
+				strSize += scnprintf(buff+strSize, buff_size-strSize,
+						"RX DRU disable\r\n");
+			}
+			break;
+		case (XVPHY_LOG_EVT_GT_PLL_LAYOUT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Couldn't find the correct GT "
+					"parameters for this video resolution.\n\r");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Try another GT PLL layout.\n\r");
+			break;
+		case (XVPHY_LOG_EVT_GT_UNBONDED):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Transmitter cannot be used in\r\n");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"bonded mode when DRU is enabled\r\n");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Switch to unbonded PLL layout\r\n");
+			break;
+		case (XVPHY_LOG_EVT_1PPC_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: The VPHY cannot support this video ");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"format at PPC = 1\r\n");
+			break;
+		case (XVPHY_LOG_EVT_PPC_MSMTCH_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: HDMI TX SS PPC value, doesn't match with"
+					" VPhy PPC value\r\n");
+			break;
+		case (XVPHY_LOG_EVT_VDCLK_HIGH_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: GTPE2 Video PHY cannot"
+								"support resolutions");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"\r\n\twith video clock > 148.5 MHz.\r\n");
+			break;
+		case (XVPHY_LOG_EVT_NO_DRU):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Warning: No DRU instance found. ");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Low resolution video isn't supported in "
+					"this design.\r\n");
+			break;
+		case (XVPHY_LOG_EVT_GT_QPLL_CFG_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: QPLL config not found!\r\n");
+			break;
+		case (XVPHY_LOG_EVT_GT_CPLL_CFG_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: CPLL config not found!\r\n");
+			break;
+		case (XVPHY_LOG_EVT_VD_NOT_SPRTD_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: This video format is not "
+					"supported by this device\r\n");
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"         "
+					"Change to another format\r\n");
+			break;
+		case (XVPHY_LOG_EVT_MMCM_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: MMCM config not found!\r\n");
+			break;
+		case (XVPHY_LOG_EVT_HDMI20_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error!  The Video PHY doesn't "
+					"support HDMI 2.0 line rates\r\n");
+			break;
+		case (XVPHY_LOG_EVT_NO_QPLL_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error!  There's no QPLL instance in the design\r\n");
+			break;
+		case (XVPHY_LOG_EVT_DRU_CLK_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: Wrong DRU REFCLK frequency detected\r\n");
+			break;
+		case (XVPHY_LOG_EVT_USRCLK_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: User Clock frequency is more than 297 MHz\r\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Unknown event %i\r\n", Evt);
+			break;
+		}
+
+		if((buff_size - strSize) > 30) {
+			/* Read log data */
+			Log = XVphy_LogRead(InstancePtr);
+		} else {
+			Log = 0;
+		}
+	}
+#else
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"\r\nINFO:: VPHY Log Feature is Disabled \r\n");
+#endif
+    return strSize;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_mmcme4.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_mmcme4.c
@@ -0,0 +1,535 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_mmcme4.c
+ *
+ * Contains a minimal set of functions for the XVphy driver that allow access
+ * to all of the Video PHY core's functionality. See xvphy.h for a detailed
+ * description of the driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.7   gm   13/09/17 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xstatus.h"
+#include "xvphy.h"
+#include "xvphy_i.h"
+#if (XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTHE4 || \
+     XPAR_VPHY_0_TRANSCEIVER == XVPHY_GTYE4)
+
+/**************************** Function Prototypes *****************************/
+static u32 XVphy_Mmcme4DividerEncoding(XVphy_MmcmDivType DivType, u8 Div);
+static u16 XVphy_Mmcme4FilterReg1Encoding(u8 Mult);
+static u16 XVphy_Mmcme4FilterReg2Encoding(u8 Mult);
+static u16 XVphy_Mmcme4LockReg1Encoding(u8 Mult);
+static u16 XVphy_Mmcme4LockReg2Encoding(u8 Mult);
+static u16 XVphy_Mmcme4LockReg3Encoding(u8 Mult);
+
+/************************** Constant Definitions ******************************/
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of ClkFbOutMult optimized for:
+* Phase = 0; Dutycycle = 0.5; No Fractional division
+* The calculations are based on XAPP888
+*
+* @param	Div is the divider to be encoded
+*
+* @return
+*		- Encoded Value for ClkReg1 [31: 0]
+*       - Encoded Value for ClkReg2 [63:32]
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_Mmcme4DividerEncoding(XVphy_MmcmDivType DivType, u8 Div)
+{
+	u32 DrpEnc;
+	u32 ClkReg1;
+    u32 ClkReg2;
+    u8 HiTime, LoTime;
+
+    if (Div == 1) {
+        ClkReg1 = 0x00001041;
+        ClkReg2 = 0x00C00000;
+    }
+    else {
+        HiTime = Div / 2;
+        LoTime = Div - HiTime;
+
+        ClkReg1 = LoTime & 0x3F;
+        ClkReg1 |= (HiTime & 0x3F) << 6;
+        ClkReg1 |= (DivType == MMCM_DIVCLK_DIVIDE) ? 0x0000 : 0x1000;
+
+        ClkReg2 = (Div % 2) ? 0x00800000 : 0x00000000;
+    }
+
+    DrpEnc = ClkReg2 | ClkReg1;
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of FilterReg1 optimized for:
+* Phase = 0; Dutycycle = 0.5; BW = low; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- Encoded Value
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_Mmcme4FilterReg1Encoding(u8 Mult)
+{
+	u16 DrpEnc;
+
+    switch (Mult) {
+	case 1: case 2: case 3:
+	case 4: case 5: case 6:
+	case 7: case 8: case 9:
+	case 10: case 11: case 12:
+	case 13: case 14: case 16:
+		DrpEnc = 0x0900;
+		break;
+    case 15:
+		DrpEnc = 0x1000;
+		break;
+		break;
+	case 17: case 19: case 20:
+    case 29: case 30: case 31:
+    case 38: case 39: case 40:
+    case 41: case 78: case 79:
+    case 80: case 81: case 82:
+    case 83: case 84: case 85:
+		DrpEnc = 0x9800;
+		break;
+    case 26: case 27: case 28:
+    case 71: case 72: case 73:
+    case 74: case 75: case 76:
+    case 77: case 120: case 121:
+    case 122: case 123: case 124:
+    case 125: case 126: case 127:
+    case 128:
+		DrpEnc = 0x9100;
+		break;
+	default:
+		DrpEnc = 0x9900;
+		break;
+	}
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of FilterReg1 optimized for:
+* Phase = 0; Dutycycle = 0.5; BW = low; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- Encoded Value
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_Mmcme4FilterReg2Encoding(u8 Mult)
+{
+	u16 DrpEnc;
+
+    switch (Mult) {
+	case 1: case 2:
+		DrpEnc = 0x9990;
+		break;
+    case 3:
+		DrpEnc = 0x9190;
+		break;
+	case 4:
+		DrpEnc = 0x1190;
+		break;
+	case 5:
+		DrpEnc = 0x8190;
+		break;
+    case 6: case 7:
+		DrpEnc = 0x9890;
+		break;
+	case 8:
+		DrpEnc = 0x0190;
+		break;
+    case 9: case 10: case 11:
+	case 15: case 17: case 18:
+        DrpEnc = 0x1890;
+		break;
+    case 12: case 13: case 14:
+	case 19: case 20: case 21:
+    case 22: case 23: case 24:
+    case 25:
+		DrpEnc = 0x8890;
+		break;
+    case 16:
+    case 26: case 27: case 28:
+    case 29: case 30: case 31:
+    case 32: case 33: case 34:
+    case 35: case 36: case 37:
+		DrpEnc = 0x9090;
+		break;
+    case 38: case 39: case 40:
+    case 41: case 42: case 43:
+    case 44: case 45: case 46:
+    case 47: case 48: case 49:
+    case 50: case 51: case 52:
+    case 53: case 54: case 55:
+    case 56: case 57: case 58:
+    case 59: case 60: case 61:
+    case 62:
+		DrpEnc = 0x0890;
+		break;
+    case 120: case 121: case 122:
+    case 123: case 124: case 125:
+    case 126: case 127: case 128:
+		DrpEnc = 0x8090;
+		break;
+	default:
+		DrpEnc = 0x1090;
+		break;
+	}
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of LockReg1 optimized for:
+* Phase = 0; Dutycycle = 0.5; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- Encoded Value
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_Mmcme4LockReg1Encoding(u8 Mult)
+{
+	u16 DrpEnc;
+
+    switch (Mult) {
+	case 1: case 2: case 3:
+	case 4: case 5: case 6:
+	case 7: case 8: case 9:
+	case 10:
+		DrpEnc = 0x03e8;
+		break;
+	case 11:
+		DrpEnc = 0x0384;
+		break;
+	case 12:
+		DrpEnc = 0x0339;
+		break;
+	case 13:
+		DrpEnc = 0x02ee;
+		break;
+	case 14:
+		DrpEnc = 0x02bc;
+		break;
+	case 15:
+		DrpEnc = 0x028a;
+		break;
+	case 16:
+		DrpEnc = 0x0271;
+		break;
+	case 17:
+		DrpEnc = 0x023f;
+		break;
+	case 18:
+		DrpEnc = 0x0226;
+		break;
+	case 19:
+		DrpEnc = 0x020d;
+		break;
+	case 20:
+		DrpEnc = 0x01f4;
+		break;
+	case 21:
+		DrpEnc = 0x01db;
+		break;
+	case 22:
+		DrpEnc = 0x01c2;
+		break;
+	case 23:
+		DrpEnc = 0x01a9;
+		break;
+	case 24:
+	case 25:
+		DrpEnc = 0x0190;
+		break;
+	case 26:
+		DrpEnc = 0x0177;
+		break;
+	case 27:
+	case 28:
+		DrpEnc = 0x015e;
+		break;
+	case 29:
+	case 30:
+		DrpEnc = 0x0145;
+		break;
+	case 31:
+	case 32:
+	case 33:
+		DrpEnc = 0x012c;
+		break;
+	case 34:
+	case 35:
+	case 36:
+		DrpEnc = 0x0113;
+		break;
+	default:
+		DrpEnc = 0x00fa;
+		break;
+	}
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of LockReg2 optimized for:
+* Phase = 0; Dutycycle = 0.5; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- Encoded Value
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_Mmcme4LockReg2Encoding(u8 Mult)
+{
+	u16 DrpEnc;
+
+    switch (Mult) {
+	case 1:
+	case 2:
+		DrpEnc = 0x1801;
+		break;
+	case 3:
+		DrpEnc = 0x2001;
+		break;
+	case 4:
+		DrpEnc = 0x2c01;
+		break;
+	case 5:
+		DrpEnc = 0x3801;
+		break;
+	case 6:
+		DrpEnc = 0x4401;
+		break;
+	case 7:
+		DrpEnc = 0x4c01;
+		break;
+	case 8:
+		DrpEnc = 0x5801;
+		break;
+	case 9:
+		DrpEnc = 0x6401;
+		break;
+	case 10:
+		DrpEnc = 0x7001;
+		break;
+	default:
+		DrpEnc = 0x7c01;
+		break;
+	}
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function returns the DRP encoding of LockReg3 optimized for:
+* Phase = 0; Dutycycle = 0.5; No Fractional division
+*
+* @param	Mult is the divider to be encoded
+*
+* @return
+*		- Encoded Value
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVphy_Mmcme4LockReg3Encoding(u8 Mult)
+{
+	u16 DrpEnc;
+
+    switch (Mult) {
+	case 1:
+	case 2:
+		DrpEnc = 0x1be9;
+		break;
+	case 3:
+		DrpEnc = 0x23e9;
+		break;
+	case 4:
+		DrpEnc = 0x2fe9;
+		break;
+	case 5:
+		DrpEnc = 0x3be9;
+		break;
+	case 6:
+		DrpEnc = 0x47e9;
+		break;
+	case 7:
+		DrpEnc = 0x4fe9;
+		break;
+	case 8:
+		DrpEnc = 0x5be9;
+		break;
+	case 9:
+		DrpEnc = 0x67e9;
+		break;
+	case 10:
+		DrpEnc = 0x73e9;
+		break;
+	default:
+		DrpEnc = 0x7fe9;
+		break;
+	}
+
+	return DrpEnc;
+}
+
+/*****************************************************************************/
+/**
+* This function will write the mixed-mode clock manager (MMCM) values currently
+* stored in the driver's instance structure to hardware .
+*
+* @param	InstancePtr is a pointer to the XVphy core instance.
+* @param	QuadId is the GT quad ID to operate on.
+* @param	Dir is an indicator for TX or RX.
+*
+* @return
+*		- XST_SUCCESS if the MMCM write was successful.
+*		- XST_FAILURE otherwise, if the configuration success bit did
+*		  not go low.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVphy_MmcmWriteParameters(XVphy *InstancePtr, u8 QuadId,
+							XVphy_DirectionType Dir)
+{
+	u8 ChId;
+	u16 DrpVal;
+	u32 DrpVal32;
+	XVphy_Mmcm *MmcmParams;
+
+    ChId = (Dir == XVPHY_DIR_TX) ?
+						XVPHY_CHANNEL_ID_TXMMCM :
+						XVPHY_CHANNEL_ID_RXMMCM;
+
+	MmcmParams = &InstancePtr->Quads[QuadId].Mmcm[Dir];
+
+	/* Check Parameters if has been Initialized */
+	if (!MmcmParams->DivClkDivide && !MmcmParams->ClkFbOutMult &&
+			!MmcmParams->ClkOut0Div && !MmcmParams->ClkOut1Div &&
+			!MmcmParams->ClkOut2Div) {
+		return XST_FAILURE;
+	}
+
+
+	/* Write Power Register Value */
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x27, 0xFFFF);
+
+	/* Write CLKFBOUT Reg1 & Reg2 Values */
+	DrpVal32 = XVphy_Mmcme4DividerEncoding(MMCM_CLKFBOUT_MULT_F,
+						MmcmParams->ClkFbOutMult);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x14,
+						(u16)(DrpVal32 & 0xFFFF));
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x15,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write DIVCLK_DIVIDE Value */
+	DrpVal32 = XVphy_Mmcme4DividerEncoding(MMCM_DIVCLK_DIVIDE,
+						MmcmParams->DivClkDivide) ;
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x16,
+						(u16)(DrpVal32 & 0xFFFF));
+
+	/* Write CLKOUT0 Reg1 & Reg2 Values */
+	DrpVal32 = XVphy_Mmcme4DividerEncoding(MMCM_CLKOUT_DIVIDE,
+						MmcmParams->ClkOut0Div);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x08,
+						(u16)(DrpVal32 & 0xFFFF));
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x09,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write CLKOUT1 Reg1 & Reg2 Values */
+	DrpVal32 = XVphy_Mmcme4DividerEncoding(MMCM_CLKOUT_DIVIDE,
+						MmcmParams->ClkOut1Div);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x0A,
+						(u16)(DrpVal32 & 0xFFFF));
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x0B,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write CLKOUT2 Reg1 & Reg2 Values */
+	DrpVal32 = XVphy_Mmcme4DividerEncoding(MMCM_CLKOUT_DIVIDE,
+						MmcmParams->ClkOut2Div);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x0C,
+						(u16)(DrpVal32 & 0xFFFF));
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x0D,
+						(u16)((DrpVal32 >> 16) & 0xFFFF));
+
+	/* Write Lock Reg1 Value */
+	DrpVal = XVphy_Mmcme4LockReg1Encoding(MmcmParams->ClkFbOutMult);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x18, DrpVal);
+
+	/* Write Lock Reg2 Value */
+	DrpVal = XVphy_Mmcme4LockReg2Encoding(MmcmParams->ClkFbOutMult);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x19, DrpVal);
+
+	/* Write Lock Reg3 Value */
+	DrpVal = XVphy_Mmcme4LockReg3Encoding(MmcmParams->ClkFbOutMult);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x1A, DrpVal);
+
+	/* Write Filter Reg1 Value */
+	DrpVal = XVphy_Mmcme4FilterReg1Encoding(MmcmParams->ClkFbOutMult);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x4E, DrpVal);
+
+	/* Write Filter Reg2 Value */
+	DrpVal = XVphy_Mmcme4FilterReg2Encoding(MmcmParams->ClkFbOutMult);
+	XVphy_DrpWr(InstancePtr, QuadId, ChId, 0x4F, DrpVal);
+
+	return XST_SUCCESS;
+}
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/phy-xilinx-vphy/xvphy_sinit.c
@@ -0,0 +1,81 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xvphy_sinit.c
+ *
+ * This file contains static initialization methods for the XVphy driver.
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   als  10/19/15 Initial release.
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xvphy.h"
+#include "xvphy_i.h"
+
+/*************************** Variable Declarations ****************************/
+
+#ifndef XPAR_XVPHY_NUM_INSTANCES
+#define XPAR_XVPHY_NUM_INSTANCES 0
+#endif
+
+/**
+ * A table of configuration structures containing the configuration information
+ * for each Video PHY core in the system.
+ */
+extern XVphy_Config XVphy_ConfigTable[XPAR_XVPHY_NUM_INSTANCES];
+
+/**************************** Function Definitions ****************************/
+
+/******************************************************************************/
+/**
+ * This function looks for the device configuration based on the unique device
+ * ID. The table XVphy_ConfigTable[] contains the configuration information for
+ * each device in the system.
+ *
+ * @param	DeviceId is the unique device ID of the device being looked up.
+ *
+ * @return	A pointer to the configuration table entry corresponding to the
+ *		given device ID, or NULL if no match is found.
+ *
+ * @note	None.
+ *
+*******************************************************************************/
+XVphy_Config *XVphy_LookupConfig(u16 DeviceId)
+{
+	XVphy_Config *CfgPtr = NULL;
+	u32 Index;
+
+	for (Index = 0; Index < XPAR_XVPHY_NUM_INSTANCES; Index++) {
+		if (XVphy_ConfigTable[Index].DeviceId == DeviceId) {
+			CfgPtr = &XVphy_ConfigTable[Index];
+			break;
+		}
+	}
+
+	return CfgPtr;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx.c
@@ -0,0 +1,1782 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirx.c
+*
+* This is the main file for Xilinx HDMI RX core. Please see xv_hdmirx.h for
+* more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  gm, mg 11/03/15 Initial release.
+* 1.01  MG     30/12/15 Added DDC HDCP 2.2 calls
+* 1.02  yh     15/01/16 Added 3D Video support
+* 1.03  MG     19/02/16 Added link error callback
+* 1.04  MG     08/03/16 Updated XV_HdmiRx_SetStream to use RefClk
+* 1.05  MG     27/05/16 Updated XV_HdmiRx_CfgInitialize
+* 1.06  YH     18/07/16 Replace xil_printf with xdbg_printf
+* 1.07  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                          XV_HdmiRx_CfgInitialize
+* 1.08  YH     18/08/16 squash unused variable compiler warning
+* 1.09  YH     29/08/16 Set Match to FALSE when HTotal = 0
+* 1.10  MG     02/03/17 Fixed YUV420 reading in function
+*                          XV_HdmiRx_GetVideoTiming
+* 1.40  YH     19/07/17 Clean up Print Statement line ending to "\r\n"
+*              05/09/17 Enhanced Video Timing checking
+* 2.00  YH     16/11/17 Added dedicated reset for each clock domain
+*       YH     16/11/17 Added bridge overflow interrupt
+*       EB     18/01/18 Moved VicTable to Hdmi Common library
+*       EB     26/01/18 Updated XV_HdmiRx_GetVideoTiming to use
+*                          XVidC_GetVideoModeIdExtensive
+* 2.20  EB     16/08/18 Replaced TIME_10MS, TIME_16MS, TIME_200MS with
+*                          XV_HdmiRx_GetTime10Ms, XV_HdmiRx_GetTime16Ms
+*                          XV_HdmiRx_GetTime200Ms
+*                       Added TMDS Clock Ratio callback support
+* 2.30  EB     05/03/19 Updated the description of the API
+*                          XV_HdmiRx_GetLinkStatus
+* 2.40  EB     30/07/19 Updated XV_HdmiRx_GetVideoTiming to fix an issue where
+*                          FrameRate for YUV420 may be incorrect
+*                       Updated XV_HdmiRx_GetVideoTiming to fix an issue where
+*                          video timing values may be incorrect
+*              06/08/19 Added Vic and Video Timing mismatch callback support
+* 2.50  EB     02/12/18 Added 3D Audio Support
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmirx.h"
+#include <linux/string.h>
+
+/************************** Constant Definitions *****************************/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+static void StubCallback(void *CallbackRef);
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function initializes the HDMI RX core. This function must be called
+* prior to using the HDMI RX core. Initialization of the HDMI RX includes
+* setting up the instance data, and ensuring the hardware is in a quiescent
+* state.
+*
+* @param    InstancePtr is a pointer to the XHdmiRx core instance.
+* @param    CfgPtr points to the configuration structure associated with
+*       the HDMI RX core.
+* @param    EffectiveAddr is the base address of the device. If address
+*       translation is being used, then this parameter must reflect the
+*       virtual base address. Otherwise, the physical address should be
+*       used.
+*
+* @return
+*       - XST_SUCCESS if XV_HdmiRx_CfgInitialize was successful.
+*       - XST_FAILURE if HDMI RX PIO ID mismatched.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_CfgInitialize(XV_HdmiRx *InstancePtr, XV_HdmiRx_Config *CfgPtr, UINTPTR EffectiveAddr)
+{
+    u32 RegValue;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(CfgPtr != NULL);
+    Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)0x0);
+
+    /* Setup the instance */
+    (void)memset((void *)InstancePtr, 0, sizeof(XV_HdmiRx));
+    (void)memcpy((void *)&(InstancePtr->Config), (const void *)CfgPtr, sizeof(XV_HdmiRx_Config));
+    InstancePtr->Config.BaseAddress = EffectiveAddr;
+
+    /* Check PIO ID */
+    RegValue = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_ID_OFFSET));
+    RegValue = ((RegValue) >> (XV_HDMIRX_SHIFT_16)) & (XV_HDMIRX_MASK_16);
+    if (RegValue != (XV_HDMIRX_PIO_ID)) {
+        return (XST_FAILURE);
+    }
+
+    /*
+        Callbacks
+        These are placeholders pointing to the StubCallback
+        The actual callback pointers will be assigned by the SetCallback function
+    */
+
+    InstancePtr->ConnectCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsConnectCallbackSet = (FALSE);
+
+    InstancePtr->AuxCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsAuxCallbackSet = (FALSE);
+
+    InstancePtr->AudCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsAudCallbackSet = (FALSE);
+
+    InstancePtr->LnkStaCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsLnkStaCallbackSet = (FALSE);
+
+    InstancePtr->DdcCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsDdcCallbackSet = (FALSE);
+
+    InstancePtr->StreamDownCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsStreamDownCallbackSet = (FALSE);
+
+    InstancePtr->StreamInitCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsStreamInitCallbackSet = (FALSE);
+
+    InstancePtr->StreamUpCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsStreamUpCallbackSet = (FALSE);
+
+    InstancePtr->HdcpCallback = (XV_HdmiRx_HdcpCallback)((void *)StubCallback);
+    InstancePtr->IsHdcpCallbackSet = (FALSE);
+
+    InstancePtr->LinkErrorCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsLinkErrorCallbackSet = (FALSE);
+
+    InstancePtr->SyncLossCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsSyncLossCallbackSet = (FALSE);
+
+    InstancePtr->ModeCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsModeCallbackSet = (FALSE);
+
+    InstancePtr->TmdsClkRatioCallback =
+				(XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsTmdsClkRatioCallbackSet = (FALSE);
+
+    InstancePtr->VicErrorCallback = (XV_HdmiRx_Callback)((void *)StubCallback);
+    InstancePtr->IsVicErrorCallbackSet = (FALSE);
+
+    /* Clear HDMI variables */
+    XV_HdmiRx_Clear(InstancePtr);
+
+    // Clear connected flag
+    InstancePtr->Stream.IsConnected = (FALSE);
+
+    // Reset all peripherals
+    XV_HdmiRx_PioDisable(InstancePtr);
+    XV_HdmiRx_TmrDisable(InstancePtr);
+    XV_HdmiRx_VtdDisable(InstancePtr);
+    XV_HdmiRx_DdcDisable(InstancePtr);
+    XV_HdmiRx_AuxDisable(InstancePtr);
+    XV_HdmiRx_AudioDisable(InstancePtr);
+    XV_HdmiRx_LnkstaDisable(InstancePtr);
+
+    XV_HdmiRx_PioIntrDisable(InstancePtr);
+    XV_HdmiRx_TmrIntrDisable(InstancePtr);
+    XV_HdmiRx_VtdIntrDisable(InstancePtr);
+    XV_HdmiRx_DdcScdcClear(InstancePtr);
+
+    /*
+        PIO peripheral
+    */
+
+    /* PIO: Set event rising edge masks */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_IN_EVT_RE_OFFSET),
+            (XV_HDMIRX_PIO_IN_BRDG_OVERFLOW_MASK) |
+			(XV_HDMIRX_PIO_IN_DET_MASK) |
+            (XV_HDMIRX_PIO_IN_LNK_RDY_MASK) |
+            (XV_HDMIRX_PIO_IN_VID_RDY_MASK) |
+            (XV_HDMIRX_PIO_IN_MODE_MASK) |
+            (XV_HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK) |
+            (XV_HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK)
+        );
+
+    /* PIO: Set event falling edge masks */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_IN_EVT_FE_OFFSET),
+            (XV_HDMIRX_PIO_IN_DET_MASK) |
+            (XV_HDMIRX_PIO_IN_VID_RDY_MASK) |
+            (XV_HDMIRX_PIO_IN_MODE_MASK) |
+            (XV_HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK) |
+            (XV_HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK)
+        );
+
+    /* Set run flag */
+    XV_HdmiRx_PioEnable(InstancePtr);
+
+    /* Enable interrupt */
+    XV_HdmiRx_PioIntrEnable(InstancePtr);
+
+    /*
+        Timer
+    */
+
+    /* Set run flag */
+    XV_HdmiRx_TmrEnable(InstancePtr);
+
+    /* Enable interrupt */
+    XV_HdmiRx_TmrIntrEnable(InstancePtr);
+
+    /*
+        Video Timing detector peripheral
+    */
+
+    // Set timebase - 16 ms
+    XV_HdmiRx_VtdSetTimebase(InstancePtr, XV_HdmiRx_GetTime16Ms(InstancePtr));
+
+    // The VTD run flag is set in the armed state
+
+    /*
+        DDC peripheral
+    */
+
+    /* Enable DDC */
+    XV_HdmiRx_DdcEnable(InstancePtr);
+
+    /* Enable DDC peripheral interrupt */
+    //XV_HdmiRx_DdcIntrEnable(InstancePtr);
+
+    // Enable SCDC
+    XV_HdmiRx_DdcScdcEnable(InstancePtr);
+
+    /*
+        AUX peripheral
+    */
+
+    // The aux peripheral will be enabled in the RX init done callback
+    //XV_HdmiRx_AuxEnable(InstancePtr);
+
+    /* Enable AUX peripheral interrupt */
+    XV_HdmiRx_AuxIntrEnable(InstancePtr);
+
+    /*
+        Audio peripheral
+    */
+
+    // The audio peripheral willl be enabled in the RX init done callback
+    //XV_HdmiRx_AudioEnable(InstancePtr);
+
+    /* Enable AUD peripheral interrupt */
+    XV_HdmiRx_AudioIntrEnable(InstancePtr);
+
+    /* Enable Link Status */
+    XV_HdmiRx_LnkstaEnable(InstancePtr);
+
+    /* Enable Link Status peripheral interrupt */
+    //XV_HdmiRx_LinkIntrEnable(InstancePtr);
+
+    /* Reset the hardware and set the flag to indicate the driver is ready */
+    InstancePtr->IsReady = (u32)(XIL_COMPONENT_IS_READY);
+
+    return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function clears the HDMI RX variables and sets them to the defaults.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     This is required after a reset or init.
+*
+******************************************************************************/
+void XV_HdmiRx_Clear(XV_HdmiRx *InstancePtr)
+{
+    u32 Index;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_DOWN;            // The stream is down
+    InstancePtr->Stream.IsHdmi = (FALSE);
+    InstancePtr->Stream.Video.ColorFormatId = (XVIDC_CSF_RGB);          // Default RGB
+    InstancePtr->Stream.Video.IsInterlaced = 0;
+    InstancePtr->Stream.Video.ColorDepth = (XVIDC_BPC_8);               // Default 8 bits
+    InstancePtr->Stream.Video.PixPerClk = (XVIDC_PPC_2);
+    InstancePtr->Stream.Video.VmId = (XVIDC_VM_NO_INPUT);
+    InstancePtr->Stream.Video.Is3D = FALSE;
+    InstancePtr->Stream.Video.Info_3D.Format = XVIDC_3D_UNKNOWN;
+    InstancePtr->Stream.Video.Timing.HActive = 0;
+    InstancePtr->Stream.Video.Timing.HFrontPorch = 0;
+    InstancePtr->Stream.Video.Timing.HSyncWidth = 0;
+    InstancePtr->Stream.Video.Timing.HBackPorch = 0;
+    InstancePtr->Stream.Video.Timing.HTotal = 0;
+    InstancePtr->Stream.Video.Timing.HSyncPolarity = 0;
+    InstancePtr->Stream.Video.Timing.VActive = 0;
+    InstancePtr->Stream.Video.Timing.F0PVFrontPorch = 0;
+    InstancePtr->Stream.Video.Timing.F0PVSyncWidth = 0;
+    InstancePtr->Stream.Video.Timing.F0PVBackPorch = 0;
+    InstancePtr->Stream.Video.Timing.F0PVTotal = 0;
+    InstancePtr->Stream.Video.Timing.F1VFrontPorch = 0;
+    InstancePtr->Stream.Video.Timing.F1VSyncWidth = 0;
+    InstancePtr->Stream.Video.Timing.F1VBackPorch = 0;
+    InstancePtr->Stream.Video.Timing.F1VTotal = 0;
+    InstancePtr->Stream.Video.Timing.VSyncPolarity = 0;
+    InstancePtr->Stream.Vic = 0;
+    InstancePtr->Stream.Audio.Active = (FALSE);                             // Idle stream
+    InstancePtr->Stream.Audio.Channels = 2;                             // 2 channels
+    InstancePtr->Stream.GetVideoPropertiesTries = 0;
+
+    /* AUX */
+    InstancePtr->Aux.Header.Data = 0;
+    for (Index = 0; Index < 8; Index++) {
+        InstancePtr->Aux.Data.Data[Index] = 0;
+    }
+
+    /* Audio */
+    InstancePtr->AudCts = 0;
+    InstancePtr->AudN = 0;
+    InstancePtr->AudFormat = 0;
+
+    // Call stream down callback
+    if (InstancePtr->IsStreamDownCallbackSet) {
+        InstancePtr->StreamDownCallback(InstancePtr->StreamDownRef);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the HDMI RX stream parameters.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    Ppc specifies the pixel per clock.
+*       - 1 = XVIDC_PPC_1
+*       - 2 = XVIDC_PPC_2
+*       - 4 = XVIDC_PPC_4
+* @param    Clock specifies reference pixel clock frequency.
+*
+* @return
+*       - XST_SUCCESS is always returned.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_SetStream(XV_HdmiRx *InstancePtr, XVidC_PixelsPerClock Ppc, u32 Clock)
+{
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid((Ppc == (XVIDC_PPC_1)) || (Ppc == (XVIDC_PPC_2))
+                                             || (Ppc == (XVIDC_PPC_4)));
+    Xil_AssertNonvoid(Clock > 0x0);
+
+    /* Pixels per clock */
+    InstancePtr->Stream.Video.PixPerClk = Ppc;
+
+    /* Reference clock */
+    InstancePtr->Stream.RefClk = Clock;
+
+    /* Set RX pixel rate */
+    XV_HdmiRx_SetPixelRate(InstancePtr);
+
+    return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI RX Internal VRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI RX Internal VRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI RX. Therefore, clearing the PIO reset output will assert
+*       the HDMI Internal video reset.
+*       C-style signature:
+*       void XV_HdmiRx_INT_VRST(XV_HdmiRx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiRx_INT_VRST(XV_HdmiRx *InstancePtr, u8 Reset)
+{
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_INT_VRST_MASK));
+    }
+    else {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_INT_VRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI RX Internal LRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI RX Internal LRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI RX. Therefore, clearing the PIO reset output will assert
+*       the HDMI Internal link reset.
+*       C-style signature:
+*       void XV_HdmiRx_INT_VRST(XV_HdmiRx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiRx_INT_LRST(XV_HdmiRx *InstancePtr, u8 Reset)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_INT_LRST_MASK));
+    }
+    else {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_INT_LRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI RX External VRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI RX External VRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI RX. Therefore, clearing the PIO reset output will assert
+*       the HDMI external video reset.
+*       C-style signature:
+*       void XV_HdmiRx_EXT_VRST(XV_HdmiRx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiRx_EXT_VRST(XV_HdmiRx *InstancePtr, u8 Reset)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_EXT_VRST_MASK));
+    }
+    else {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_EXT_VRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI RX External SYSRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI RX External SYSRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI RX. Therefore, clearing the PIO reset output will assert
+*       the HDMI External system reset.
+*       C-style signature:
+*       void XV_HdmiRx_EXT_SYSRST(XV_HdmiRx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiRx_EXT_SYSRST(XV_HdmiRx *InstancePtr, u8 Reset)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_EXT_SYSRST_MASK));
+    }
+    else {
+        XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_EXT_SYSRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the pixel rate.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - XST_SUCCESS is always returned.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_SetPixelRate(XV_HdmiRx *InstancePtr)
+{
+    u32 RegValue;
+    u8 PixelRate;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* Mask pixel rate */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_MSK_OFFSET), (XV_HDMIRX_PIO_OUT_PIXEL_RATE_MASK));
+
+    /* Check pixel per clock */
+    switch (InstancePtr->Stream.Video.PixPerClk) {
+        case (XVIDC_PPC_2):
+            PixelRate = 1;
+            break;
+
+        case (XVIDC_PPC_4):
+            PixelRate = 2;
+            break;
+
+        default:
+            PixelRate = 0;
+            break;
+    }
+
+    /* Set pixel rate for video path */
+    RegValue = PixelRate << (XV_HDMIRX_PIO_OUT_PIXEL_RATE_SHIFT);
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_OFFSET), RegValue);
+
+    return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the color format
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRx_SetColorFormat(XV_HdmiRx *InstancePtr)
+{
+    u32 RegValue;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Mask PIO Out Mask register */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_MSK_OFFSET), (XV_HDMIRX_PIO_OUT_COLOR_SPACE_MASK));
+
+    /* Check for color format */
+    switch (InstancePtr->Stream.Video.ColorFormatId) {
+        case (XVIDC_CSF_YCRCB_444):
+            RegValue = 1;
+            break;
+
+        case (XVIDC_CSF_YCRCB_422):
+            RegValue = 2;
+            break;
+
+        case (XVIDC_CSF_YCRCB_420):
+            RegValue = 3;
+            break;
+
+        default:
+            RegValue = 0;
+            break;
+    }
+
+    /* Write color space into PIO Out register */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_OFFSET), (RegValue << (XV_HDMIRX_PIO_OUT_COLOR_SPACE_SHIFT)));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables/clear Hot-Plug-Detect.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    SetClr specifies TRUE/FALSE value to either enable or
+*       clear HPD respectively.
+*
+* @return
+*       - XST_SUCCESS is always returned.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_SetHpd(XV_HdmiRx *InstancePtr, u8 SetClr)
+{
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid((SetClr == (TRUE)) || (SetClr == (FALSE)));
+
+    if (SetClr) {
+        /* Set HPD */
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_HPD_MASK));
+    }
+    else {
+        /* Clear HPD */
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_HPD_MASK));
+    }
+
+    return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides status of the HDMI RX core Link Status peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    Type specifies one of the type for which status to be provided:
+*       - 0 = Link error counter for channel 0.
+*       - 1 = Link error counter for channel 1.
+*       - 2 = Link error counter for channel 2.
+*
+* @return   Link status of the HDMI RX core link.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiRx_GetLinkStatus(XV_HdmiRx *InstancePtr, u8 Type)
+{
+    u32 RegValue;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(Type < 0x6);
+
+    RegValue = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_LNKSTA_LNK_ERR0_OFFSET) + (4 * Type));
+
+    return RegValue;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides status of one of the link error counters reached the
+* maximum value.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - TRUE = Maximum error counter reached.
+*       - FALSE = Maximum error counter not reached.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_IsLinkStatusErrMax(XV_HdmiRx *InstancePtr)
+{
+    u32 Status;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* Read Link Status peripheral Status register */
+    Status = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_LNKSTA_STA_OFFSET)) & (XV_HDMIRX_LNKSTA_STA_ERR_MAX_MASK);
+
+    if (Status) {
+        Status = (TRUE);
+    }
+    else {
+        Status = (FALSE);
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function clears the link error counters.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRx_ClearLinkStatus(XV_HdmiRx *InstancePtr)
+{
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Set Error Clear bit */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_LNKSTA_CTRL_SET_OFFSET), (XV_HDMIRX_LNKSTA_CTRL_ERR_CLR_MASK));
+
+    /* Clear Error Clear bit */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_LNKSTA_CTRL_CLR_OFFSET), (XV_HDMIRX_LNKSTA_CTRL_ERR_CLR_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides audio clock regenerating CTS (Cycle-Time Stamp) value
+* at the HDMI sink device.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   Audio clock CTS value.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiRx_GetAcrCts(XV_HdmiRx *InstancePtr)
+{
+    u32 CtsValue;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* Read cycle time stamp value */
+    CtsValue = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUD_CTS_OFFSET));
+
+    return CtsValue;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides audio clock regenerating factor N value.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   ACR N value.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiRx_GetAcrN(XV_HdmiRx *InstancePtr)
+{
+    u32 AcrNValue;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* Read ACR factor N value */
+    AcrNValue = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUD_N_OFFSET));
+
+    return AcrNValue;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the size of the EDID buffer of the DDC slave.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - EDID buffer size
+*
+* @note     None.
+*
+******************************************************************************/
+u16 XV_HdmiRx_DdcGetEdidWords(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_EDID_STA_OFFSET));
+    Data >>= XV_HDMIRX_DDC_STA_EDID_WORDS_SHIFT;
+    Data &= XV_HDMIRX_DDC_STA_EDID_WORDS_MASK;
+    return (Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function loads the EDID data into the DDC slave.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param    EdidData is a pointer to the EDID data array.
+* @param    Length is the length, in bytes, of the EDID array.
+*
+* @return
+*       - XST_SUCCESS if the EDID data was loaded successfully
+*       - XST_FAILURE if the EDID data load failed
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_DdcLoadEdid(XV_HdmiRx *InstancePtr, u8 *EdidData, u16 Length)
+{
+    u8 Data;
+    u16 Index;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Check if the EDID data fits in the DDC slave EDID buffer
+    if (XV_HdmiRx_DdcGetEdidWords(InstancePtr) >= Length)
+    {
+        // Clear EDID write pointer
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_EDID_WP_OFFSET), 0);
+
+        // Copy EDID data
+        for (Index = 0; Index < Length; Index++) {
+            Data = *(EdidData + Index);
+            XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_EDID_DATA_OFFSET), (Data));
+        }
+
+        // Enable EDID
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_EDID_EN_MASK));
+
+        return (XST_SUCCESS);
+    }
+
+    // The EDID data is larger than the DDC slave EDID buffer size
+    else
+    {
+        xdbg_printf(XDBG_DEBUG_GENERAL,"The EDID data structure is too large to be stored in the DDC peripheral (%0d).\r\n", Length);
+        return (XST_FAILURE);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP address in the DDC peripheral.
+* This is implemented as a function and not a macro, so the HDCP driver can bind the function call with a handler.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+* @param    Address is the HDCP address.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XHdmiRx_DdcHdcpSetAddress(XHdmi_Rx *InstancePtr, u8 Address)
+*
+******************************************************************************/
+void XV_HdmiRx_DdcHdcpSetAddress(XV_HdmiRx *InstancePtr, u32 Address)
+{
+    // Verify argument.
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    // Write Address
+    XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_ADDRESS_OFFSET), (Address));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function writes HDCP data in the DDC peripheral.
+* This is implemented as a function and not a macro, so the HDCP driver can bind the function call with a handler.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+* @param    Data is the HDCP data to be written.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XHdmiRx_DdcHdcpWriteData(XHdmi_Rx *InstancePtr, u8 Data)
+*
+******************************************************************************/
+void XV_HdmiRx_DdcHdcpWriteData(XV_HdmiRx *InstancePtr, u32 Data)
+{
+    // Verify argument.
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    // Write data
+    XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_DATA_OFFSET), (Data));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads HDCP data from the DDC peripheral.
+* This is implemented as a function and not a macro, so the HDCP driver can bind the function call with a handler.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return   Returns the HDCP data read from the DDC peripheral.
+*
+* @note     C-style signature:
+*       u32 XHdmiRx_DdcHdcpReadData(XHdmi_Rx *InstancePtr)
+*
+******************************************************************************/
+u32 XV_HdmiRx_DdcHdcpReadData(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    Data = XV_HdmiRx_ReadReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_DATA_OFFSET));
+    return (Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the number of bytes of the HDCP 2.2 write buffer in the DDC slave.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return
+*       - HDCP 2.2 write buffer words
+*
+* @note     None.
+*
+******************************************************************************/
+u16 XV_HdmiRx_DdcGetHdcpWriteMessageBufferWords(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_STA_OFFSET));
+    Data >>= XV_HDMIRX_DDC_STA_HDCP_WMSG_WORDS_SHIFT;
+    Data &= XV_HDMIRX_DDC_STA_HDCP_WMSG_WORDS_MASK;
+    return (Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the status of the HDCP 2.2 write buffer in the DDC slave.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return
+*       - TRUE = HDCP 2.2 message buffer is empty.
+*       - FALSE = HDCP 2.2 message buffer contains data.
+*
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_DdcIsHdcpWriteMessageBufferEmpty(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_STA_OFFSET));
+    if (Data & XV_HDMIRX_DDC_STA_HDCP_WMSG_EP_MASK)
+        return (TRUE);
+    else
+        return (FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the number of bytes of the HDCP 2.2 read buffer in the DDC slave.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return
+*       - HDCP 2.2 read buffer words
+*
+* @note     None.
+*
+******************************************************************************/
+u16 XV_HdmiRx_DdcGetHdcpReadMessageBufferWords(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_STA_OFFSET));
+    Data >>= XV_HDMIRX_DDC_STA_HDCP_RMSG_WORDS_SHIFT;
+    Data &= XV_HDMIRX_DDC_STA_HDCP_RMSG_WORDS_MASK;
+    return (Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the status of the HDCP 2.2 read message buffer in the DDC slave.
+*
+* @param    InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return
+*       - TRUE = HDCP 2.2 message buffer is empty.
+*       - FALSE = HDCP 2.2 message buffer contains data.
+*
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_DdcIsHdcpReadMessageBufferEmpty(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_HDCP_STA_OFFSET));
+    if (Data & XV_HDMIRX_DDC_STA_HDCP_RMSG_EP_MASK)
+        return (TRUE);
+    else
+        return (FALSE);
+}
+
+/******************************************************************************/
+/**
+*
+* This function prints stream and timing information on STDIO/Uart console.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRx_DebugInfo(XV_HdmiRx *InstancePtr)
+{
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Print stream information */
+    XVidC_ReportStreamInfo(&InstancePtr->Stream.Video);
+
+    /* Print timing information */
+    XVidC_ReportTiming(&InstancePtr->Stream.Video.Timing, InstancePtr->Stream.Video.IsInterlaced);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides status of the stream
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - TRUE = Stream is up.
+*       - FALSE = Stream is down.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_IsStreamUp(XV_HdmiRx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_UP) {
+        return (TRUE);
+    }
+    else {
+        return (FALSE);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides the stream scrambler status
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - TRUE = Stream is scrambled.
+*       - FALSE = Stream is not scrambled.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_IsStreamScrambled(XV_HdmiRx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    return (InstancePtr->Stream.IsScrambled);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides the stream connected status
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - TRUE = Stream is connected.
+*       - FALSE = Stream is connected.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_IsStreamConnected(XV_HdmiRx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    return (InstancePtr->Stream.IsConnected);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the SCDC TMDS clock ratio bit
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*       - TRUE = TMDS clock ratio bit is set.
+*       - FALSE = TMDS clock ratio bit is cleared.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_GetTmdsClockRatio(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_IN_OFFSET));
+
+    if ((Data) & (XV_HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK))
+        return (TRUE);
+    else
+        return (FALSE);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the AVI VIC (captured by the AUX peripheral)
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   The AVI VIC code.
+*
+* @note     None.
+*
+******************************************************************************/
+u8 XV_HdmiRx_GetAviVic(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET));
+    Data >>= XV_HDMIRX_AUX_STA_AVI_VIC_SHIFT;
+    Data &= XV_HDMIRX_AUX_STA_AVI_VIC_MASK;
+    return (u8)(Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the AVI colorspace (captured by the AUX peripheral)
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   The AVI colorspace value.
+*
+* @note     None.
+*
+******************************************************************************/
+XVidC_ColorFormat XV_HdmiRx_GetAviColorSpace(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+    XVidC_ColorFormat ColorSpace;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET));
+    Data >>= XV_HDMIRX_AUX_STA_AVI_CS_SHIFT;
+    Data &= XV_HDMIRX_AUX_STA_AVI_CS_MASK;
+
+        switch (Data) {
+            case 1:
+                ColorSpace = (XVIDC_CSF_YCRCB_422);
+                break;
+
+            case 2:
+                ColorSpace = (XVIDC_CSF_YCRCB_444);
+                break;
+
+            case 3:
+                ColorSpace = (XVIDC_CSF_YCRCB_420);
+                break;
+
+            default:
+                ColorSpace = (XVIDC_CSF_RGB);
+                break;
+        }
+    return (ColorSpace);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the GCP color depth (captured by the AUX peripheral)
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   The GCP color depth.
+*
+* @note     None.
+*
+******************************************************************************/
+XVidC_ColorDepth XV_HdmiRx_GetGcpColorDepth(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+    XVidC_ColorDepth ColorDepth;
+
+    // Verify argument.
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Read status register
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET));
+    Data >>= XV_HDMIRX_AUX_STA_GCP_CD_SHIFT;
+    Data &= XV_HDMIRX_AUX_STA_GCP_CD_MASK;
+
+        switch (Data) {
+            case 1:
+                ColorDepth = (XVIDC_BPC_10);
+                break;
+
+            case 2:
+                ColorDepth = (XVIDC_BPC_12);
+                break;
+
+            case 3:
+                ColorDepth = (XVIDC_BPC_16);
+                break;
+
+            default:
+                ColorDepth = (XVIDC_BPC_8);
+                break;
+        }
+    return (ColorDepth);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function calculates the divider for the frame calculation
+*
+* @param    Dividend is the dividend value to use in the calculation.
+* @param    Divisor is the divisor value to use in the calculation.
+*
+* @return   The result of the calculation.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiRx_Divide(u32 Dividend, u32 Divisor)
+{
+    u32 Result;
+    u32 Remainder;
+    Result = Dividend / Divisor;
+    Remainder = Dividend % Divisor;
+    if (Remainder) {
+        if (Remainder > (Divisor/2))
+            Result += 1;
+    }
+    return (Result);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function searches for the video mode based on the vic.
+*
+* @param    Vic
+*
+* @return   Vic defined in the VIC table.
+*
+* @note     None.
+*
+******************************************************************************/
+XVidC_VideoMode XV_HdmiRx_LookupVmId(u8 Vic)
+{
+    XHdmiC_VicTable const *Entry;
+    u8 Index;
+
+    for (Index = 0; Index < sizeof(VicTable)/sizeof(XHdmiC_VicTable); Index++) {
+      Entry = &VicTable[Index];
+      if (Entry->Vic == Vic)
+        return (Entry->VmId);
+    }
+    return XVIDC_VM_NOT_SUPPORTED;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads the video properties from the aux peripheral
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_GetVideoProperties(XV_HdmiRx *InstancePtr)
+{
+	u32 Status;
+
+	// Read AUX peripheral status register
+	Status =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET));
+
+	// Check if AVI ready flag has been set
+	if ((Status) & (XV_HDMIRX_AUX_STA_AVI_MASK)) {
+
+		// Get AVI colorspace
+		InstancePtr->Stream.Video.ColorFormatId = XV_HdmiRx_GetAviColorSpace(InstancePtr);
+
+		// Get AVI Vic
+		InstancePtr->Stream.Vic = XV_HdmiRx_GetAviVic(InstancePtr);
+
+		// Get GCP colordepth
+		// In HDMI the colordepth in YUV422 is always 12 bits (although on the link itself it is being transmitted as 8-bits.
+		// Therefore if the colorspace is YUV422, then force the colordepth to 12 bits.
+		if (InstancePtr->Stream.Video.ColorFormatId == XVIDC_CSF_YCRCB_422) {
+			InstancePtr->Stream.Video.ColorDepth = XVIDC_BPC_12;
+		}
+
+		// Else read the colordepth from the general control packet
+		else {
+			InstancePtr->Stream.Video.ColorDepth = XV_HdmiRx_GetGcpColorDepth(InstancePtr);
+		}
+		return (XST_SUCCESS);
+	}
+
+	else {
+
+		// If we tried more than 8 times and still haven't received any AVI infoframes,
+		// then the source is DVI.
+		// In this case the video properties are forced to RGB and 8 bpc.
+		if (InstancePtr->Stream.GetVideoPropertiesTries > 7) {
+
+			// Force AVI colorspace to RGB
+			InstancePtr->Stream.Video.ColorFormatId = XVIDC_CSF_RGB;
+
+			// Set AVI vic to zero
+			InstancePtr->Stream.Vic = 0;
+
+			// Force color depth to 8 bpc
+			InstancePtr->Stream.Video.ColorDepth = XVIDC_BPC_8;
+
+			return (XST_SUCCESS);
+		}
+
+		// Return
+		else {
+			// Increment tries
+			InstancePtr->Stream.GetVideoPropertiesTries++;
+			return (XST_FAILURE);
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads the video timing from the VTD peripheral
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRx_GetVideoTiming(XV_HdmiRx *InstancePtr)
+{
+    u32 Data;
+
+    XVidC_VideoStream VidStreamCopy;
+
+    // Local timing parameters
+    u16 HActive;
+    u16 HFrontPorch;
+    u16 HSyncWidth;
+    u16 HBackPorch;
+    u16 HTotal;
+    // u16 HSyncPolarity; //squash unused variable compiler warning
+    u16 VActive;
+    u16 F0PVFrontPorch;
+    u16 F0PVSyncWidth;
+    u16 F0PVBackPorch;
+    u16 F0PVTotal;
+    u16 F1VFrontPorch;
+    u16 F1VSyncWidth;
+    u16 F1VBackPorch;
+    u16 F1VTotal;
+    u8 Match;
+    u8 YUV420_Correction;
+    u8 IsInterlaced;
+
+    InstancePtr->Stream.Video.VmId = XVIDC_VM_NOT_SUPPORTED;
+
+    // If the colorspace is YUV420, then the horizontal parameters must be doubled
+    if (InstancePtr->Stream.Video.ColorFormatId == XVIDC_CSF_YCRCB_420) {
+        YUV420_Correction = 2;
+    } else {
+        YUV420_Correction = 1;
+    }
+
+    // First we read the video parameters from the VTD and store them in a local variable
+    /* Read Total Pixels */
+    HTotal =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_TOT_PIX_OFFSET)) * YUV420_Correction;
+
+    /* Read Active Pixels */
+    HActive =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_ACT_PIX_OFFSET)) * YUV420_Correction;
+
+    /* Read Hsync Width */
+    HSyncWidth =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_HSW_OFFSET)) * YUV420_Correction;
+
+    /* Read HFront Porch */
+    HFrontPorch =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_HFP_OFFSET)) * YUV420_Correction;
+
+    /* Read HBack Porch */
+    HBackPorch =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_HBP_OFFSET)) * YUV420_Correction;
+
+    /* Total lines field 1 */
+    F0PVTotal =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_TOT_LIN_OFFSET)) & (0xFFFF);
+
+    /* Total lines field 2 */
+    F1VTotal =  ((XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_TOT_LIN_OFFSET))) >> 16);
+
+    /* Active lines field 1 */
+    VActive =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_ACT_LIN_OFFSET)) & (0xFFFF);
+
+    /* Read VSync Width field 1*/
+    F0PVSyncWidth =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_VSW_OFFSET)) & (0xFFFF);
+
+    /* Read VSync Width field 2*/
+    F1VSyncWidth =  ((XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_VSW_OFFSET))) >> 16);
+
+    /* Read VFront Porch field 1*/
+    F0PVFrontPorch =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_VFP_OFFSET)) & (0xFFFF);
+
+    /* Read VFront Porch field 2*/
+    F1VFrontPorch =  ((XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_VFP_OFFSET))) >> 16);
+
+    /* Read VBack Porch field 1 */
+    F0PVBackPorch =  XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_VBP_OFFSET)) & (0xFFFF);
+
+    /* Read VBack Porch field 2 */
+    F1VBackPorch =  ((XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_VBP_OFFSET))) >> 16);
+
+    /* Read Status register */
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_STA_OFFSET));
+
+    /* Check video format */
+    if ((Data) & (XV_HDMIRX_VTD_STA_FMT_MASK)) {
+        /* Interlaced */
+        IsInterlaced = 1;
+    }
+    else {
+        /* Progressive */
+        IsInterlaced = 0;
+    }
+
+    // Next, we compare these values with the previous stored values
+    // By default the match is true
+    Match = TRUE;
+
+    if (!HActive | !HFrontPorch | !HSyncWidth | !HBackPorch | !HTotal | !VActive |
+        !F0PVFrontPorch | !F0PVSyncWidth | !F0PVBackPorch | !F0PVTotal) {
+        Match = FALSE;
+    }
+
+	if (IsInterlaced == 1) {
+		if ((!F1VTotal || !VActive || !F1VFrontPorch ||
+			!F1VSyncWidth || !F1VBackPorch) ||
+			(F1VTotal != (VActive + F1VFrontPorch +
+				F1VSyncWidth + F1VBackPorch))) {
+			Match = FALSE;
+		}
+	} else {
+		if (F1VFrontPorch | F1VSyncWidth | F1VBackPorch) {
+			Match = FALSE;
+		}
+	}
+
+    // Htotal
+    if (HTotal != InstancePtr->Stream.Video.Timing.HTotal) {
+        Match = FALSE;
+    }
+
+    // HActive
+    if (HActive != InstancePtr->Stream.Video.Timing.HActive) {
+        Match = FALSE;
+    }
+
+    // HSyncWidth
+    if (HSyncWidth != InstancePtr->Stream.Video.Timing.HSyncWidth) {
+        Match = FALSE;
+    }
+
+    // HFrontPorch
+    if (HFrontPorch != InstancePtr->Stream.Video.Timing.HFrontPorch) {
+        Match = FALSE;
+    }
+
+    // HBackPorch
+    if (HBackPorch != InstancePtr->Stream.Video.Timing.HBackPorch) {
+        Match = FALSE;
+    }
+
+    // F0PVTotal
+    if (F0PVTotal != InstancePtr->Stream.Video.Timing.F0PVTotal) {
+        Match = FALSE;
+    }
+
+    // F1VTotal
+    if (F1VTotal != InstancePtr->Stream.Video.Timing.F1VTotal) {
+        Match = FALSE;
+    }
+
+    // VActive
+    if (VActive != InstancePtr->Stream.Video.Timing.VActive) {
+        Match = FALSE;
+    }
+
+    // F0PVSyncWidth
+    if (F0PVSyncWidth != InstancePtr->Stream.Video.Timing.F0PVSyncWidth) {
+        Match = FALSE;
+    }
+
+    // F1VSyncWidth
+    if (F1VSyncWidth != InstancePtr->Stream.Video.Timing.F1VSyncWidth) {
+        Match = FALSE;
+    }
+
+    // F0PVFrontPorch
+    if (F0PVFrontPorch != InstancePtr->Stream.Video.Timing.F0PVFrontPorch) {
+        Match = FALSE;
+    }
+
+    // F1VFrontPorch
+    if (F1VFrontPorch != InstancePtr->Stream.Video.Timing.F1VFrontPorch) {
+        Match = FALSE;
+    }
+
+    // F0PVBackPorch
+    if (F0PVBackPorch != InstancePtr->Stream.Video.Timing.F0PVBackPorch) {
+        Match = FALSE;
+    }
+
+    // F1VBackPorch
+    if (F1VBackPorch != InstancePtr->Stream.Video.Timing.F1VBackPorch) {
+        Match = FALSE;
+    }
+
+    if (HTotal != (HActive + HFrontPorch + HSyncWidth +HBackPorch)) {
+        Match = FALSE;
+    }
+
+    if (F0PVTotal != (VActive + F0PVFrontPorch + F0PVSyncWidth +F0PVBackPorch)) {
+        Match = FALSE;
+    }
+
+    // Then we store the timing parameters regardless if there was a match
+    /* Read Total Pixels */
+    InstancePtr->Stream.Video.Timing.HTotal =  HTotal;
+
+    /* Read Active Pixels */
+    InstancePtr->Stream.Video.Timing.HActive = HActive;
+
+    /* Read Hsync Width */
+    InstancePtr->Stream.Video.Timing.HSyncWidth = HSyncWidth;
+
+    /* Read HFront Porch */
+    InstancePtr->Stream.Video.Timing.HFrontPorch = HFrontPorch;
+
+    /* Read HBack Porch */
+    InstancePtr->Stream.Video.Timing.HBackPorch = HBackPorch;
+
+    /* Total lines field 1 */
+    InstancePtr->Stream.Video.Timing.F0PVTotal = F0PVTotal;
+
+    /* Total lines field 2 */
+    InstancePtr->Stream.Video.Timing.F1VTotal = F1VTotal;
+
+    /* Active lines field 1 */
+    InstancePtr->Stream.Video.Timing.VActive = VActive;
+
+    /* Read VSync Width field 1*/
+    InstancePtr->Stream.Video.Timing.F0PVSyncWidth = F0PVSyncWidth;
+
+    /* Read VSync Width field 2*/
+    InstancePtr->Stream.Video.Timing.F1VSyncWidth = F1VSyncWidth;
+
+    /* Read VFront Porch field 1*/
+    InstancePtr->Stream.Video.Timing.F0PVFrontPorch = F0PVFrontPorch;
+
+    /* Read VFront Porch field 2*/
+    InstancePtr->Stream.Video.Timing.F1VFrontPorch = F1VFrontPorch;
+
+    /* Read VBack Porch field 1 */
+    InstancePtr->Stream.Video.Timing.F0PVBackPorch =  F0PVBackPorch;
+
+    /* Read VBack Porch field 2 */
+    InstancePtr->Stream.Video.Timing.F1VBackPorch =  F1VBackPorch;
+
+    // Do we have a match?
+    // Yes, then continue processing
+    if (Match) {
+
+        /* Read Status register */
+        Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_STA_OFFSET));
+
+        /* Check video format */
+        if ((Data) & (XV_HDMIRX_VTD_STA_FMT_MASK)) {
+            /* Interlaced */
+            InstancePtr->Stream.Video.IsInterlaced = 1;
+        }
+        else {
+            /* Progressive */
+            InstancePtr->Stream.Video.IsInterlaced = 0;
+        }
+
+        /* Check Vsync polarity */
+        if ((Data) & (XV_HDMIRX_VTD_STA_VS_POL_MASK)) {
+            /* Positive */
+            InstancePtr->Stream.Video.Timing.VSyncPolarity = 1;
+        }
+        else {
+            /* Negative */
+            InstancePtr->Stream.Video.Timing.VSyncPolarity = 0;
+        }
+
+        /* Check Hsync polarity */
+        if ((Data) & (XV_HDMIRX_VTD_STA_HS_POL_MASK)) {
+            /* Positive */
+            InstancePtr->Stream.Video.Timing.HSyncPolarity = 1;
+        }
+        else {
+            /* Negative */
+            InstancePtr->Stream.Video.Timing.HSyncPolarity = 0;
+        }
+
+        /* Calculate and set the frame rate field assuming the stream is
+         * of YUV420 */
+        InstancePtr->Stream.Video.FrameRate =
+    		    (XVidC_FrameRate) (XV_HdmiRx_Divide((InstancePtr->Stream.PixelClk << 1),
+    				    (InstancePtr->Stream.Video.Timing.F0PVTotal *
+    						    InstancePtr->Stream.Video.Timing.HTotal)));
+
+        /* If the colorspace is not YUV420, then the frame rate must be
+         * halved */
+        if (InstancePtr->Stream.Video.ColorFormatId != XVIDC_CSF_YCRCB_420) {
+            InstancePtr->Stream.Video.FrameRate >>= 1;
+        }
+
+        // Lookup the video mode id
+        InstancePtr->Stream.Video.VmId =
+        XVidC_GetVideoModeIdExtensive(&InstancePtr->Stream.Video.Timing,
+        		InstancePtr->Stream.Video.FrameRate,
+			InstancePtr->Stream.Video.IsInterlaced,
+			(TRUE));
+
+        //If video mode not found in the table tag it as custom
+        if (InstancePtr->Stream.Video.VmId == XVIDC_VM_NOT_SUPPORTED) {
+            InstancePtr->Stream.Video.VmId = XVIDC_VM_CUSTOM;
+        }
+
+        VidStreamCopy = InstancePtr->Stream.Video;
+
+        if (XVidC_IsStream3D(&InstancePtr->Stream.Video)){
+            XVidC_Set3DVideoStream(&InstancePtr->Stream.Video,
+                                   VidStreamCopy.VmId,
+                                   VidStreamCopy.ColorFormatId,
+                                   VidStreamCopy.ColorDepth,
+                                   VidStreamCopy.PixPerClk,
+                                   &VidStreamCopy.Info_3D);
+        } else {
+            XVidC_SetVideoStream(&InstancePtr->Stream.Video,
+                                 VidStreamCopy.VmId,
+                                 VidStreamCopy.ColorFormatId,
+                                 VidStreamCopy.ColorDepth,
+                                 VidStreamCopy.PixPerClk);
+        }
+
+        // Return success
+        return (XST_SUCCESS);
+    }
+
+    // No match
+    else {
+        return (XST_FAILURE);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a stub for the asynchronous callback. The stub is here in
+* case the upper layer forgot to set the handlers. On initialization, all
+* handlers are set to this callback. It is considered an error for this
+* handler to be invoked.
+*
+* @param    CallbackRef is a callback reference passed in by the upper
+*       layer when setting the callback functions, and passed back to
+*       the upper layer when the callback is invoked.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+static void StubCallback(void *CallbackRef)
+{
+    Xil_AssertVoid(CallbackRef != NULL);
+    Xil_AssertVoidAlways();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx.h
@@ -0,0 +1,1317 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirx.h
+*
+* This is the main header file for Xilinx HDMI RX core. HDMI RX core is used
+* for extracting the video and audio streams from HDMI stream. It consists of
+* - Receiver core
+* - AXI4-Stream to Video Bridge
+* - Video Timing Controller and
+* - High-bandwidth Digital Content Protection (HDCP) (Optional)
+* - Data Recovery Unit (DRU) (Optional).
+*
+* Receiver core performs following operations:
+* - Aligns incoming data stream to the word boundary and removes inter channel
+* skew.
+* - Unscrambles the data if data rates above the 3.4 Gps. Otherwise bypasses
+* the Scrambler.
+* - Splits the data stream into video and packet data streams.
+* - Optional data streams decrypt by an external HDCP module.
+* - Decodes TMDS data into video data.
+* - Converts the pixel data from the link domain into the video domain.
+*
+* AXI Video Bridge converts the captured native video to AXI stream and outputs
+* the video data through the AXI video interface.
+*
+* Video Timing Controller (VTC) measures the video timing.
+*
+* Data Recovery Unit (DRU) to recover the data from the HDMI stream if incoming
+* HDMI stream is too slow for the transceiver.
+*
+* <b>Core Features </b>
+*
+* For a full description of HDMI RX features, please see the hardware
+* specification.
+*
+* <b>Software Initialization & Configuration</b>
+*
+* The application needs to do following steps in order for preparing the
+* HDMI RX core to be ready.
+*
+* - Call XV_HdmiRx_LookupConfig using a device ID to find the core configuration.
+* - Call XV_HdmiRx_CfgInitialize to initialize the device and the driver
+* instance associated with it.
+*
+* <b>Interrupts </b>
+*
+* This driver provides interrupt handlers
+* - XV_HdmiRx_IntrHandler, for handling the interrupts from the HDMI RX core
+* peripherals.
+*
+* Application developer needs to register interrupt handler with the processor,
+* within their examples. Whenever processor calls registered application's
+* interrupt handler associated with interrupt id, application's interrupt
+* handler needs to call appropriate peripheral interrupt handler reading
+* peripheral's Status register.
+
+* This driver provides XV_HdmiRx_SetCallback API to register functions with HDMI
+* RX core instance.
+*
+* <b> Virtual Memory </b>
+*
+* This driver supports Virtual Memory. The RTOS is responsible for calculating
+* the correct device base address in Virtual Memory space.
+*
+* <b> Threads </b>
+*
+* This driver is not thread safe. Any needs for threads or thread mutual
+* exclusion must be satisfied by the layer above this driver.
+*
+* <b> Asserts </b>
+*
+* Asserts are used within all Xilinx drivers to enforce constraints on argument
+* values. Asserts can be turned off on a system-wide basis by defining, at
+* compile time, the NDEBUG identifier. By default, asserts are turned on and it
+* is recommended that users leave asserts on during development.
+*
+* <b> Building the driver </b>
+*
+* The HDMI RX driver is composed of several source files. This allows the user
+* to build and link only those parts of the driver that are necessary.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  gm, mg 10/07/15 Initial release.
+* 1.01  yh     14/01/16 Added Marco for AxisEnable PIO
+* 1.02  yh     15/01/16 Added 3D Video support
+* 1.03  MG     18/02/16 Added link error callback.
+* 1.04  MG     08/03/16 Added RefClk to structure XV_HdmiRx_Stream
+* 1.05  MG     13/05/16 Added XV_HdmiRx_DdcHdcp22Mode and XV_HdmiRx_DdcHdcp14
+*                       Mode macros
+* 1.06  MG     27/05/16 Added VTD timebase macro
+* 1.07  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                          XV_HdmiRx_Config
+*                          XV_HdmiRx_CfgInitialize
+* 1.08  YH     14/11/16 Added XV_HdmiRx_Bridge_yuv420 & XV_HdmiRx_Bridge_pixel
+*                          mode macros
+* 1.09  MMO    02/03/17 Added Sync Loss and IsMode Handler for HDCP
+*                          compliance test.
+* 1.10  EB     24/10/17 Added enum XV_HdmiRx_AudioFormatType for AudFormat
+* 2.00  YH     16/11/17 Added dedicated reset for each clock domain
+*                       Added bridge overflow interrupt
+*       EB     18/01/18 Moved VicTable, XV_HdmiRx_Aux to Hdmi Common library
+*                       Moved Vendor Specific InfoFrame related functions to
+*                           HDMI Common library
+*                       Deprecating XV_HdmiRx_VSIF_ParsePacket,
+*                           XV_HdmiRx_VSIF_DisplayInfo,
+*                           XV_HdmiRx_VSIF_3DStructToString,
+*                           XV_HdmiRx_VSIF_3DSampMethodToString and
+*                           XV_HdmiRx_VSIF_3DSampPosToString APIs
+*       MMO    08/02/18 Added XV_HdmiRx_SyncStatus enumaration, and as
+*                           an element in XV_HdmiRx_Stream for Sync Loss
+*                           handling
+* 2.20  EB     16/08/18 Replaced TIME_10MS, TIME_16MS, TIME_200MS with
+*                           XV_HdmiRx_GetTime10Ms, XV_HdmiRx_GetTime16Ms
+*                           XV_HdmiRx_GetTime200Ms
+*                       Added TMDS Clock Ratio callback support
+*       YB     15/08/18	Added new callbacks for HDCP 1.4 & 2.2 protocol events.
+*                       Enumerated new entries for HDCP 1.4 & 2.2 protocol
+*                           events in XV_HdmiRx_HandlerType enum.
+* 2.50  EB     02/12/18 Added 3D Audio Support
+* </pre>
+*
+******************************************************************************/
+#ifndef XV_HDMIRX_H_
+#define XV_HDMIRX_H_		/**< Prevent circular inclusions
+				  *  by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmirx_hw.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xdebug.h"
+#include "xvidc.h"
+#include "xv_hdmic.h"
+
+/************************** Constant Definitions *****************************/
+
+/** @name Handler Types
+* @{
+*/
+/**
+* These constants specify different types of handler and used to differentiate
+* interrupt requests from peripheral.
+*/
+typedef enum {
+	XV_HDMIRX_HANDLER_CONNECT = 1,	/**< A connect event interrupt type */
+	XV_HDMIRX_HANDLER_BRDG_OVERFLOW,    /**< Interrupt type for bridge
+	                                     overflow */
+	XV_HDMIRX_HANDLER_AUX,			/**< Interrupt type for AUX peripheral */
+	XV_HDMIRX_HANDLER_AUD,			/**< Interrupt type for AUD peripheral */
+	XV_HDMIRX_HANDLER_LNKSTA,		/**< Interrupt type for LNKSTA peripheral */
+	XV_HDMIRX_HANDLER_DDC,			/**< Interrupt type for DDC	peripheral */
+	XV_HDMIRX_HANDLER_STREAM_DOWN,	/**< Interrupt type for stream down */
+	XV_HDMIRX_HANDLER_STREAM_INIT,	/**< Interrupt type for stream init */
+	XV_HDMIRX_HANDLER_STREAM_UP,	/**< Interrupt type for stream up */
+	XV_HDMIRX_HANDLER_HDCP,			/**< Interrupt type for hdcp */
+	XV_HDMIRX_HANDLER_DDC_HDCP_14_PROT,  /**< Interrupt type for HDCP14PROT event */
+	XV_HDMIRX_HANDLER_DDC_HDCP_22_PROT,  /**< Interrupt type for HDCP22PROT event */
+	XV_HDMIRX_HANDLER_LINK_ERROR,		/**< Interrupt type for link error */
+	XV_HDMIRX_HANDLER_SYNC_LOSS,       /**< Interrupt type for sync loss */
+	XV_HDMIRX_HANDLER_MODE,            /**< Interrupt type for mode */
+	XV_HDMIRX_HANDLER_TMDS_CLK_RATIO, /**< Interrupt type for TMDS clock ratio */
+	XV_HDMIRX_HANDLER_VIC_ERROR	/**< Interrupt type for VIC error */
+} XV_HdmiRx_HandlerType;
+/*@}*/
+
+/** @name HDMI RX stream status
+* @{
+*/
+typedef enum {
+	XV_HDMIRX_STATE_STREAM_DOWN,			/**< Stream down */
+	XV_HDMIRX_STATE_STREAM_IDLE,			/**< Stream idle */
+	XV_HDMIRX_STATE_STREAM_INIT,			/**< Stream init */
+	XV_HDMIRX_STATE_STREAM_ARM,				/**< Stream arm */
+	XV_HDMIRX_STATE_STREAM_LOCK,			/**< Stream lock */
+	XV_HDMIRX_STATE_STREAM_RDY,				/**< Stream ready */
+	XV_HDMIRX_STATE_STREAM_UP				/**< Stream up */
+} XV_HdmiRx_State;
+
+/** @name HDMI RX sync status
+* @{
+*/
+typedef enum {
+	XV_HDMIRX_SYNCSTAT_SYNC_LOSS,			/**< Sync Loss */
+	XV_HDMIRX_SYNCSTAT_SYNC_EST,			/**< Sync Lock */
+} XV_HdmiRx_SyncStatus;
+
+/** @name HDMI RX audio format
+* @{
+*/
+typedef enum {
+	XV_HDMIRX_AUDFMT_UNKNOWN = 0,
+	XV_HDMIRX_AUDFMT_LPCM,	// L-PCM
+	XV_HDMIRX_AUDFMT_HBR,	// HBR
+	XV_HDMIRX_AUDFMT_3D	// 3D Audio
+} XV_HdmiRx_AudioFormatType;
+
+
+/**************************** Type Definitions *******************************/
+
+/**
+* This typedef contains configuration information for the HDMI RX core.
+* Each HDMI RX device should have a configuration structure associated.
+*/
+typedef struct {
+	u16 DeviceId;		/**< DeviceId is the unique ID of the HDMI RX core */
+	UINTPTR BaseAddress;	/**< BaseAddress is the physical base address
+						* of the core's registers */
+
+	u32 AxiLiteClkFreq;
+} XV_HdmiRx_Config;
+
+/**
+* This typedef contains HDMI RX audio stream specific data structure.
+*/
+typedef struct {
+	u8	Active;			/**< Active flag. This flag is set when an acitve audio
+						* stream was detected */
+	u8 	Channels;		/**< Channels */
+} XV_HdmiRx_AudioStream;
+
+/**
+* This typedef contains HDMI RX stream specific data structure.
+*/
+typedef struct {
+	XVidC_VideoStream 	Video;			/**< Video stream for HDMI RX */
+	XV_HdmiRx_AudioStream	Audio;		/**< Audio stream */
+	u8 	Vic;							/**< Video Identification code flag */
+	u8 	IsHdmi;							/**< HDMI flag. 1 - HDMI Stream, 0 - DVI Stream */
+	u32 PixelClk;						/**< Pixel Clock */
+	u32 RefClk;							/**< Reference Clock */
+	u8 	IsScrambled; 					/**< Scrambler flag 1 - scrambled data ,
+										*	0 - non scrambled data */
+	XV_HdmiRx_State	State;				/**< State */
+	XV_HdmiRx_SyncStatus SyncStatus;    /**< Stream Sync Status*/
+	u8 	IsConnected;					/**< Connected flag. This flag is set when
+										* the cable is connected */
+	u8 GetVideoPropertiesTries;			/** This value is used  in the GetVideoProperties API*/
+} XV_HdmiRx_Stream;
+
+/**
+* Callback type for interrupt.
+*
+* @param	CallbackRef is a callback reference passed in by the upper
+*		layer when setting the callback functions, and passed back to
+*		the upper layer when the callback is invoked.
+*
+* @return	None.
+*
+* @note		None.
+*
+*/
+typedef void (*XV_HdmiRx_Callback)(void *CallbackRef);
+typedef void (*XV_HdmiRx_HdcpCallback)(void *CallbackRef, int Data);
+
+/**
+* The XHdmiRx driver instance data. An instance must be allocated for each
+* HDMI RX core in use.
+*/
+typedef struct {
+	XV_HdmiRx_Config Config;				/**< Hardware Configuration */
+	u32 IsReady;							/**< Core and the driver instance are initialized */
+
+	/*Callbacks */
+	XV_HdmiRx_Callback ConnectCallback;		/**< Callback for connect event interrupt */
+	void *ConnectRef;						/**< To be passed to the connect interrupt callback */
+	u32 IsConnectCallbackSet;				/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback AuxCallback;			/**< Callback for AUX event interrupt */
+	void *AuxRef;							/**< To be passed to the AUX interrupt callback */
+	u32 IsAuxCallbackSet;					/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback AudCallback;			/**< Callback for AUD event interrupt */
+	void *AudRef;							/**< To be passed to the Audio interrupt callback */
+	u32 IsAudCallbackSet;					/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback LnkStaCallback;		/**< Callback for LNKSTA event interrupt */
+	void *LnkStaRef;						/**< To be passed to the LNKSTA interrupt callback */
+	u32 IsLnkStaCallbackSet;				/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback DdcCallback;			/**< Callback for PDDC interrupt */
+	void *DdcRef;							/**< To be passed to the DDC interrupt callback */
+	u32 IsDdcCallbackSet;					/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback StreamDownCallback;	/**< Callback for stream down callback */
+	void *StreamDownRef;					/**< To be passed to the stream down callback */
+	u32	IsStreamDownCallbackSet;			/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback StreamInitCallback;	/**< Callback for stream init callback */
+	void *StreamInitRef;					/**< To be passed to the stream start callback */
+	u32 IsStreamInitCallbackSet;			/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback StreamUpCallback;		/**< Callback for stream up callback */
+	void *StreamUpRef;						/**< To be passed to the stream up callback */
+	u32 IsStreamUpCallbackSet;				/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_HdcpCallback HdcpCallback;	/**< Callback for hdcp callback */
+	void *HdcpRef;							/**< To be passed to the hdcp callback */
+	u32	IsHdcpCallbackSet;					/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback Hdcp14ProtEvtCallback; /**< Callback for hdcp 1.4 protocol event written on the ddc. */
+	void *Hdcp14ProtEvtRef;					  /**< To be passed to the hdcp 1.4 protocol event callback */
+	u32 IsHdcp14ProtEvtCallbackSet;			  /**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback Hdcp22ProtEvtCallback; /**< Callback for hdcp 2.2 protocol event written on the ddc. */
+	void *Hdcp22ProtEvtRef;					  /**< To be passed to the hdcp 2.2 protocol event callback */
+	u32 IsHdcp22ProtEvtCallbackSet;			  /**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback LinkErrorCallback;	/**< Callback for link error callback */
+	void *LinkErrorRef;						/**< To be passed to the link error callback */
+	u32 IsLinkErrorCallbackSet;				/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback BrdgOverflowCallback;/**< Callback for bridge overflow callback */
+	void *BrdgOverflowRef;					/**< To be passed to the bridge overflow callback */
+	u32 IsBrdgOverflowCallbackSet;			/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback SyncLossCallback;		/**< Callback for sync loss callback */
+	void *SyncLossRef;						/**< To be passed to the link error callback */
+	u32 IsSyncLossCallbackSet;				/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback ModeCallback;			/**< Callback for sync loss callback */
+	void *ModeRef;							/**< To be passed to the link error callback */
+	u32 IsModeCallbackSet;					/**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback TmdsClkRatioCallback;    /**< Callback for TMDS clock ratio change */
+	void *TmdsClkRatioRef;                  /**< To be passed to the TMDS callback */
+	u32 IsTmdsClkRatioCallbackSet;          /**< Set flag. This flag is set to true when the callback has been registered */
+
+	XV_HdmiRx_Callback VicErrorCallback;	/**< Callback for Vic error detection */
+	void *VicErrorRef;			/**< To be passed to the vic error callback */
+	u32 IsVicErrorCallbackSet;		/**< Set flag. This flag is set to true when the callback has been registered */
+
+	/* HDMI RX stream */
+	XV_HdmiRx_Stream Stream;				/**< HDMI RX stream information */
+
+	/* Aux peripheral specific */
+	XHdmiC_Aux Aux;					/**< AUX peripheral information */
+
+	/* Audio peripheral specific */
+	u32 AudCts;								/**< Audio CTS */
+	u32 AudN;								/**< Audio N element */
+	XV_HdmiRx_AudioFormatType AudFormat;	/**< Audio Format */
+} XV_HdmiRx;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the clock cycles required to count up to 10MS with respect
+* to AXI Lite Frequency
+*
+* @param  InstancePtr is a pointer to the XV_HdmiRX core instance.
+*
+* @return None.
+*
+*
+******************************************************************************/
+#define XV_HdmiRx_GetTime10Ms(InstancePtr) \
+  (InstancePtr)->Config.AxiLiteClkFreq/100
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the clock cycles required to count up to 16MS with
+* respect to AXI Lite Frequency
+*
+* @param  InstancePtr is a pointer to the XV_HdmiRX core instance.
+*
+* @return None.
+*
+*
+******************************************************************************/
+#define XV_HdmiRx_GetTime16Ms(InstancePtr) \
+  ((InstancePtr)->Config.AxiLiteClkFreq*10)/625
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the clock cycles required to count up to 200MS with
+* respect to AXI Lite Frequency
+*
+* @param  InstancePtr is a pointer to the XV_HdmiRX core instance.
+*
+* @return None.
+*
+*
+******************************************************************************/
+#define XV_HdmiRx_GetTime200Ms(InstancePtr) \
+  (InstancePtr)->Config.AxiLiteClkFreq/5
+
+/*****************************************************************************/
+/**
+*
+* This macro reads the RX version
+*
+* @param  InstancePtr is a pointer to the XHdmi_RX core instance.
+*
+* @return RX version.
+*
+* *note	C-style signature:
+*		u32 XV_HdmiRx_GetVersion(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_GetVersion(InstancePtr) \
+  XV_HdmiRx_ReadReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_VER_VERSION_OFFSET))
+
+/*****************************************************************************/
+/**
+*
+* This macro asserts or clears the HDMI RX reset.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param	Reset specifies TRUE/FALSE value to either assert or
+*		release HDMI RX reset.
+*
+* @return	None.
+*
+* @note		The reset output of the PIO is inverted. When the system is
+*		in reset, the PIO output is cleared and this will reset the
+*		HDMI RX. Therefore, clearing the PIO reset output will assert
+*		the HDMI link and video reset.
+*		C-style signature:
+*		void XV_HdmiRx_Reset(XV_HdmiRx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+#define XV_HdmiRx_Reset(InstancePtr, Reset) \
+{ \
+	if (Reset) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_RESET_MASK)); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_RESET_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro asserts or clears the HDMI RX link enable.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either assert or
+*		release HDMI RX link enable.
+*
+* @return	None.
+*
+* @note
+*		C-style signature:
+*		void XV_HdmiRx_Reset(XV_HdmiRx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiRx_LinkEnable(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_LNK_EN_MASK)); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_LNK_EN_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro asserts or clears the HDMI RX video enable.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either assert or
+*		release HDMI RX video enable.
+*
+* @return	None.
+*
+* @note
+*		C-style signature:
+*		void XV_HdmiRx_Reset(XV_HdmiRx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiRx_VideoEnable(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_VID_EN_MASK)); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_VID_EN_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro controls the HDMI RX Scrambler.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Rx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either enable or disable the
+*		scrambler.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_SetScrambler(XV_HdmiRx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiRx_SetScrambler(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_SCRM_MASK)); \
+		(InstancePtr)->Stream.IsScrambled = (TRUE); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_SCRM_MASK)); \
+		(InstancePtr)->Stream.IsScrambled = (FALSE); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro controls the YUV420 mode for video bridge.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Rx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either enable or disable the
+*		YUV 420 Support.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_Bridge_yuv420(XV_HdmiRx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiRx_Bridge_yuv420(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_BRIDGE_YUV420_MASK)); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_BRIDGE_YUV420_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro controls the Pixel Drop mode for video bridge.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Rx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either enable or disable the
+*		Pixel Repitition.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_Bridge_pixel(XV_HdmiRx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiRx_Bridge_pixel(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_BRIDGE_PIXEL_MASK)); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_BRIDGE_PIXEL_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro asserts or clears the AXIS enable output port.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+* @param	Reset specifies TRUE/FALSE value to either assert or
+*		release HDMI RX reset.
+*
+* @return	None.
+*
+* @note		The reset output of the PIO is inverted. When the system is
+*		in reset, the PIO output is cleared and this will reset the
+*		HDMI RX. Therefore, clearing the PIO reset output will assert
+*		the HDMI link and video reset.
+*		C-style signature:
+*		void XV_HdmiRx_AxisEnable(InstancePtr, Enable)
+*
+******************************************************************************/
+#define XV_HdmiRx_AxisEnable(InstancePtr, Enable) \
+{ \
+	if (Enable) { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_SET_OFFSET), (XV_HDMIRX_PIO_OUT_AXIS_EN_MASK)); \
+	} \
+	else { \
+		XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_OUT_CLR_OFFSET), (XV_HDMIRX_PIO_OUT_AXIS_EN_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX PIO peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_PioEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_PioEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_CTRL_SET_OFFSET), (XV_HDMIRX_PIO_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX PIO peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_PioDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_PioDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_CTRL_CLR_OFFSET), (XV_HDMIRX_PIO_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupts in the HDMI RX PIO peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_PioIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_PioIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_CTRL_SET_OFFSET), (XV_HDMIRX_PIO_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupts in the HDMI RX PIO peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_PioIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_PioIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_PIO_CTRL_CLR_OFFSET), (XV_HDMIRX_PIO_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX timer peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_TmrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_TmrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_TMR_CTRL_SET_OFFSET), (XV_HDMIRX_TMR_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX timer peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_TmrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_TmrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_TMR_CTRL_CLR_OFFSET), (XV_HDMIRX_TMR_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupts in the HDMI RX timer peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_TmrIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_TmrIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_TMR_CTRL_SET_OFFSET), (XV_HDMIRX_TMR_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupt in the HDMI RX timer peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_TmrIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_TmrIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_TMR_CTRL_CLR_OFFSET), (XV_HDMIRX_TMR_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro starts the HDMI RX timer peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_TmrStart(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_TmrStart(InstancePtr, Value) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_TMR_CNT_OFFSET), (u32)(Value))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX Timing Detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_VtdEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_VtdEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_VTD_CTRL_SET_OFFSET), (XV_HDMIRX_VTD_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX Timing Detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_VtdDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_VtdDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_VTD_CTRL_CLR_OFFSET), (XV_HDMIRX_VTD_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupt in the HDMI RX Timing Detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_VtdIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_VtdIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_VTD_CTRL_SET_OFFSET), (XV_HDMIRX_VTD_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupt in the HDMI RX Timing Detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_VtdIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_VtdIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_VTD_CTRL_CLR_OFFSET), (XV_HDMIRX_VTD_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the timebase in the HDMI RX Timing Detector peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_VtdSetTimebase(XV_HdmiRx *InstancePtr, Value)
+*
+******************************************************************************/
+#define XV_HdmiRx_VtdSetTimebase(InstancePtr, Value) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_VTD_CTRL_OFFSET), (u32)(Value << XV_HDMIRX_VTD_CTRL_TIMEBASE_SHIFT))
+
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX Display Data Channel (DDC) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the SCDC in the DDC peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcScdcEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcScdcEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_SCDC_EN_MASK));
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDCP in the DDC peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcHdcpEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcHdcpEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_HDCP_EN_MASK));
+
+#define XV_HdmiRx_DdcHdcpDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_CLR_OFFSET), (XV_HDMIRX_DDC_CTRL_HDCP_EN_MASK));
+
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the DDC peripheral into HDCP 1.4 mode.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcHdcp14Mode(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcHdcp14Mode(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_CLR_OFFSET), (XV_HDMIRX_DDC_CTRL_HDCP_MODE_MASK));
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the DDC peripheral into HDCP 2.2 mode.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcHdcp22Mode(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcHdcp22Mode(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_HDCP_MODE_MASK));
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX Display Data Channel (DDC) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_CLR_OFFSET), (XV_HDMIRX_DDC_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupts in the HDMI RX Display Data Channel (DDC)
+* peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupts in the HDMI RX Display Data Channel (DDC)
+* peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_CLR_OFFSET), (XV_HDMIRX_DDC_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro clears the SCDC registers in the DDC peripheral
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_DdcScdcClear(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcScdcClear(InstancePtr) \
+{ \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_SCDC_CLR_MASK)); \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_CLR_OFFSET), (XV_HDMIRX_DDC_CTRL_SCDC_CLR_MASK)); \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX Auxiliary (AUX) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AuxEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AuxEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUX_CTRL_SET_OFFSET), (XV_HDMIRX_AUX_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX Auxiliary (AUX) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AuxDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AuxDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUX_CTRL_CLR_OFFSET), (XV_HDMIRX_AUX_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupts in the HDMI RX Auxiliary (AUX) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AuxIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AuxIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUX_CTRL_SET_OFFSET), (XV_HDMIRX_AUX_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupts in the HDMI RX Auxiliary (AUX) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AuxIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AuxIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUX_CTRL_CLR_OFFSET), (XV_HDMIRX_AUX_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX Audio (AUD) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AudioEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AudioEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUD_CTRL_SET_OFFSET), (XV_HDMIRX_AUD_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX Audio (AUD) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AudioDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AudioDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUD_CTRL_CLR_OFFSET), (XV_HDMIRX_AUD_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupts in the HDMI RX Audio (AUD) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AudioIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AudioIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUD_CTRL_SET_OFFSET), (XV_HDMIRX_AUD_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupts in the HDMI RX Audio (AUD) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_AudioIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_AudioIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_AUD_CTRL_CLR_OFFSET), (XV_HDMIRX_AUD_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI RX Link Status (LNKSTA) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_LinkstaEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_LnkstaEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_LNKSTA_CTRL_SET_OFFSET), (XV_HDMIRX_LNKSTA_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI RX Link Status (LNKSTA) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_LinkstaDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_LnkstaDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_LNKSTA_CTRL_CLR_OFFSET), (XV_HDMIRX_LNKSTA_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupt in the HDMI RX Link Status (LNKSTA) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_LinkIntrEnable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_LinkIntrEnable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_LNKSTA_CTRL_SET_OFFSET), (XV_HDMIRX_LNKSTA_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disable interrupt in the HDMI RX Link Status (LNKSTA) peripheral.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiRx_LinkIntrDisable(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_LinkIntrDisable(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_LNKSTA_CTRL_CLR_OFFSET), (XV_HDMIRX_LNKSTA_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro returns true is the audio stream is active else false
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	TRUE if the audio stream is active, FALSE if it is not.
+*
+* @note		C-style signature:
+*		u32 XV_HdmiRx_IsAudioActive(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_IsAudioActive(InstancePtr) \
+	(InstancePtr)->Stream.Audio.Active
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the number of active audio channels.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return	Number of active audio channels.
+*
+* @note		C-style signature:
+*		u32 XV_HdmiRx_GetAudioChannels(XV_HdmiRx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_GetAudioChannels(InstancePtr) \
+	(InstancePtr)->Stream.Audio.Channels
+
+/*****************************************************************************/
+/**
+*
+* This macro clears the HDCP write message buffer in the DDC peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XHdmiRx_DdcHdcpClearWriteMessageBuffer(XHdmi_Rx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcHdcpClearWriteMessageBuffer(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_WMSG_CLR_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro clears the HDCP read message buffer in the DDC peripheral.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Rx core instance.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XHdmiRx_DdcHdcpClearReadMessageBuffer(XHdmi_Rx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiRx_DdcHdcpClearReadMessageBuffer(InstancePtr) \
+	XV_HdmiRx_WriteReg((InstancePtr)->Config.BaseAddress, (XV_HDMIRX_DDC_CTRL_SET_OFFSET), (XV_HDMIRX_DDC_CTRL_RMSG_CLR_MASK))
+
+/************************** Function Prototypes ******************************/
+
+/* Initialization function in xv_hdmirx_sinit.c */
+XV_HdmiRx_Config *XV_HdmiRx_LookupConfig(u16 DeviceId);
+
+/* Initialization and control functions in xv_hdmirx.c */
+int XV_HdmiRx_CfgInitialize(XV_HdmiRx *InstancePtr, XV_HdmiRx_Config *CfgPtr, UINTPTR EffectiveAddr);
+void XV_HdmiRx_Clear(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_SetStream(XV_HdmiRx *InstancePtr, XVidC_PixelsPerClock Ppc, u32 Clock);
+int XV_HdmiRx_IsStreamUp(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_IsStreamScrambled(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_IsStreamConnected(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_SetHpd(XV_HdmiRx *InstancePtr, u8 SetClr);
+void XV_HdmiRx_INT_VRST(XV_HdmiRx *InstancePtr, u8 Reset);
+void XV_HdmiRx_INT_LRST(XV_HdmiRx *InstancePtr, u8 Reset);
+void XV_HdmiRx_EXT_VRST(XV_HdmiRx *InstancePtr, u8 Reset);
+void XV_HdmiRx_EXT_SYSRST(XV_HdmiRx *InstancePtr, u8 Reset);
+int XV_HdmiRx_SetPixelRate(XV_HdmiRx *InstancePtr);
+void XV_HdmiRx_SetColorFormat(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_IsLinkStatusErrMax(XV_HdmiRx *InstancePtr);
+void XV_HdmiRx_ClearLinkStatus(XV_HdmiRx *InstancePtr);
+u32 XV_HdmiRx_GetLinkStatus(XV_HdmiRx *InstancePtr, u8 Type);
+u32 XV_HdmiRx_GetAcrCts(XV_HdmiRx *InstancePtr);
+u32 XV_HdmiRx_GetAcrN(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_DdcLoadEdid(XV_HdmiRx *InstancePtr, u8 *Data, u16 Length);
+void XV_HdmiRx_DdcHdcpSetAddress(XV_HdmiRx *InstancePtr, u32 Addr);
+void XV_HdmiRx_DdcHdcpWriteData(XV_HdmiRx *InstancePtr, u32 Data);
+u32 XV_HdmiRx_DdcHdcpReadData(XV_HdmiRx *InstancePtr);
+u16 XV_HdmiRx_DdcGetHdcpWriteMessageBufferWords(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_DdcIsHdcpWriteMessageBufferEmpty(XV_HdmiRx *InstancePtr);
+u16 XV_HdmiRx_DdcGetHdcpReadMessageBufferWords(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_DdcIsHdcpReadMessageBufferEmpty(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_GetTmdsClockRatio(XV_HdmiRx *InstancePtr);
+u8 XV_HdmiRx_GetAviVic(XV_HdmiRx *InstancePtr);
+XVidC_ColorFormat XV_HdmiRx_GetAviColorSpace(XV_HdmiRx *InstancePtr);
+XVidC_ColorDepth XV_HdmiRx_GetGcpColorDepth(XV_HdmiRx *InstancePtr);
+XVidC_VideoMode XV_HdmiRx_LookupVmId(u8 Vic);
+int XV_HdmiRx_GetVideoProperties(XV_HdmiRx *InstancePtr);
+int XV_HdmiRx_GetVideoTiming(XV_HdmiRx *InstancePtr);
+u32 XV_HdmiRx_Divide(u32 Dividend, u32 Divisor);
+
+/* Log specific functions */
+void XV_HdmiRx_DebugInfo(XV_HdmiRx *InstancePtr);
+
+/* Self test function in xv_hdmirx_selftest.c */
+int XV_HdmiRx_SelfTest(XV_HdmiRx *InstancePtr);
+
+/* Interrupt related function in xv_hdmirx_intr.c */
+void XV_HdmiRx_IntrHandler(void *InstancePtr);
+int XV_HdmiRx_SetCallback(XV_HdmiRx *InstancePtr,
+		XV_HdmiRx_HandlerType HandlerType,
+		void *CallbackFunc,
+		void *CallbackRef);
+
+
+/* [Linux] No need to add vendor specific API */
+/************************** Variable Declarations ****************************/
+/************************** Variable Declarations ****************************/
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* End of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx_hw.h
@@ -0,0 +1,381 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirx_hw.h
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx HDMI RX core.
+*
+* For more information about the operation of this core see the hardware
+* specification and documentation in the higher level driver xv_hdmirx.h file.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  gm, mg 11/03/15 Initial release.
+* 1.01  MG     30/12/15 Added DDC peripheral HDCP 2.2 masks
+* 1.02  yh     14/01/16 Added Bit Masking for AxisEnable PIO
+* 1.03  MG     18/02/16 Added AUX peripheral error event mask
+* 1.04  MG     13/05/16 Added DDC HDCP mode mask
+* 1.05  MG     27/05/16 Added VTD timebase
+* 1.06  MH     26/07/16 Added DDC HDCP protocol event.
+* 1.07  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XV_HdmiRx_WriteReg
+*                       XV_HdmiRx_ReadReg
+* 1.08  YH     14/11/16 Added BRIDGE_YUV420 and BRIDGE_PIXEL mask to PIO Out
+* 1.09  MMO    02/03/17 Added XV_HDMIRX_VTD_CTRL_SYNC_LOSS_MASK and
+*                          XV_HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK for HDCP
+*                          compliance
+* 1.10  EB     15/11/17 Added XV_HDMIRX_AUX_STA_GCP_CD_EVT_MASK
+* 1.10  YH     16/11/17 Added PIO_IN for bridge overflow interrupt
+*              16/11/17 Added PIO_OUT for dedicated reset for each clock domain
+* </pre>
+*
+******************************************************************************/
+#ifndef XV_HDMIRX_HW_H_
+#define XV_HDMIRX_HW_H_     /**< Prevent circular inclusions
+                  *  by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+
+// VER (Version Interface) peripheral register offsets
+#define XV_HDMIRX_VER_BASE                          (0*64)
+#define XV_HDMIRX_VER_ID_OFFSET                     ((XV_HDMIRX_VER_BASE)+(0*4))    /**< VER Identification *  Register offset */
+#define XV_HDMIRX_VER_VERSION_OFFSET                    ((XV_HDMIRX_VER_BASE)+(1*4))    /**< VER Version Register *  offset */
+
+// PIO (Parallel Interface) peripheral register offsets
+#define XV_HDMIRX_PIO_BASE                          (1*64)
+#define XV_HDMIRX_PIO_ID_OFFSET                     ((XV_HDMIRX_PIO_BASE)+(0*4))    /**< PIO Identification register offset */
+#define XV_HDMIRX_PIO_CTRL_OFFSET                   ((XV_HDMIRX_PIO_BASE)+(1*4))    /**< PIO Control register offset */
+#define XV_HDMIRX_PIO_CTRL_SET_OFFSET               ((XV_HDMIRX_PIO_BASE)+(2*4))    /**< PIO Control Register Set offset */
+#define XV_HDMIRX_PIO_CTRL_CLR_OFFSET               ((XV_HDMIRX_PIO_BASE)+(3*4))    /**< PIO Control Register Clear offset */
+#define XV_HDMIRX_PIO_STA_OFFSET                        ((XV_HDMIRX_PIO_BASE)+(4*4))    /**< PIO Status Register offset */
+#define XV_HDMIRX_PIO_OUT_OFFSET                        ((XV_HDMIRX_PIO_BASE)+(5*4))    /**< PIO Out Register offset */
+#define XV_HDMIRX_PIO_OUT_SET_OFFSET                    ((XV_HDMIRX_PIO_BASE)+(6*4))    /**< PIO Out Register Set offset */
+#define XV_HDMIRX_PIO_OUT_CLR_OFFSET                    ((XV_HDMIRX_PIO_BASE)+(7*4))    /**< PIO Out Register Clear offset */
+#define XV_HDMIRX_PIO_OUT_MSK_OFFSET                    ((XV_HDMIRX_PIO_BASE)+(8*4))    /**< PIO Out Mask Register  offset */
+#define XV_HDMIRX_PIO_IN_OFFSET                     ((XV_HDMIRX_PIO_BASE)+(9*4))    /**< PIO In Register offset */
+#define XV_HDMIRX_PIO_IN_EVT_OFFSET                 ((XV_HDMIRX_PIO_BASE)+(10*4))   /**< PIO In Event Register offset */
+#define XV_HDMIRX_PIO_IN_EVT_RE_OFFSET              ((XV_HDMIRX_PIO_BASE)+(11*4))   /**< PIO In Event Rising Edge Register offset */
+#define XV_HDMIRX_PIO_IN_EVT_FE_OFFSET              ((XV_HDMIRX_PIO_BASE)+(12*4))   /**< PIO In Event Falling Edge Register offset */
+
+// PIO peripheral Control register masks
+#define XV_HDMIRX_PIO_CTRL_RUN_MASK                 (1<<0)  /**< PIO Control Run mask */
+#define XV_HDMIRX_PIO_CTRL_IE_MASK                  (1<<1)  /**< PIO Control Interrupt Enable mask */
+
+// PIO peripheral Status register masks
+#define XV_HDMIRX_PIO_STA_IRQ_MASK                  (1<<0)  /**< PIO Status Interrupt mask */
+#define XV_HDMIRX_PIO_STA_EVT_MASK                  (1<<1)  /**< PIO Status Event mask */
+
+// PIO peripheral PIO Out register masks and shifts
+#define XV_HDMIRX_PIO_OUT_RESET_MASK                    (1<<0)  /**< PIO Out Reset mask */
+#define XV_HDMIRX_PIO_OUT_LNK_EN_MASK               (1<<1)  /**< PIO Out video enable mask */
+#define XV_HDMIRX_PIO_OUT_VID_EN_MASK               (1<<2)  /**< PIO Out video enable mask */
+#define XV_HDMIRX_PIO_OUT_HPD_MASK                  (1<<3)  /**< PIO Out Hot-Plug Detect mask */
+#define XV_HDMIRX_PIO_OUT_DEEP_COLOR_MASK           0x30    /**< PIO Out Deep Color mask */
+#define XV_HDMIRX_PIO_OUT_PIXEL_RATE_MASK           0xC0    /**< PIO Out Pixel Rate mask */
+#define XV_HDMIRX_PIO_OUT_SAMPLE_RATE_MASK          0x300   /**< PIO Out Sample Rate mask */
+#define XV_HDMIRX_PIO_OUT_COLOR_SPACE_MASK          0xC00   /**< PIO Out Color Space mask */
+#define XV_HDMIRX_PIO_OUT_AXIS_EN_MASK              0x80000 /**< PIO Out Axis Enable mask */
+#define XV_HDMIRX_PIO_OUT_DEEP_COLOR_SHIFT          4       /**< PIO Out Deep Color shift */
+#define XV_HDMIRX_PIO_OUT_PIXEL_RATE_SHIFT          6       /**< PIO Out Pixel Rate Shift */
+#define XV_HDMIRX_PIO_OUT_SAMPLE_RATE_SHIFT         8       /**< PIO Out Sample Rate shift */
+#define XV_HDMIRX_PIO_OUT_COLOR_SPACE_SHIFT         10      /**< PIO Out Color Space shift */
+#define XV_HDMIRX_PIO_OUT_SCRM_MASK                 (1<<12) /**< PIO Out Scrambler mask */
+#define XV_HDMIRX_PIO_OUT_BRIDGE_YUV420_MASK        (1<<29) /**< PIO Out Bridge_YUV420 mask */
+#define XV_HDMIRX_PIO_OUT_BRIDGE_PIXEL_MASK         (1<<30) /**< PIO Out Bridge_Pixel drop mask */
+
+#define XV_HDMIRX_PIO_OUT_INT_VRST_MASK             (1<<0)  /**< PIO Out INT_VRST mask */
+#define XV_HDMIRX_PIO_OUT_INT_LRST_MASK             (1<<20) /**< PIO Out INT_LRST mask */
+#define XV_HDMIRX_PIO_OUT_EXT_VRST_MASK             (1<<21) /**< PIO Out EXT_VRST mask */
+#define XV_HDMIRX_PIO_OUT_EXT_SYSRST_MASK           (1<<22) /**< PIO Out EXT_SYSRST mask */
+
+// PIO peripheral PIO In register masks
+#define XV_HDMIRX_PIO_IN_DET_MASK                   (1<<0) /**< PIO In cable detect mask */
+#define XV_HDMIRX_PIO_IN_LNK_RDY_MASK               (1<<1) /**< PIO In link ready mask */
+#define XV_HDMIRX_PIO_IN_VID_RDY_MASK               (1<<2) /**< PIO In video ready mask */
+#define XV_HDMIRX_PIO_IN_MODE_MASK                  (1<<3) /**< PIO In Mode mask */
+#define XV_HDMIRX_PIO_IN_SCRAMBLER_LOCK0_MASK       (1<<4) /**< PIO In Scrambler lock 0 mask */
+#define XV_HDMIRX_PIO_IN_SCRAMBLER_LOCK1_MASK       (1<<5) /**< PIO In Scrambler lock 1 mask */
+#define XV_HDMIRX_PIO_IN_SCRAMBLER_LOCK2_MASK       (1<<6) /**< PIO In Scrambler lock 2 mask */
+#define XV_HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK (1<<7) /**< PIO In SCDC scrambler enable mask */
+#define XV_HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK (1<<8) /**< PIO In SCDC TMDS clock ratio mask */
+#define XV_HDMIRX_PIO_IN_ALIGNER_LOCK_MASK			(1<<9) /**< PIO In alinger lock mask */
+#define XV_HDMIRX_PIO_IN_BRDG_OVERFLOW_MASK         (1<<10) /**< PIO In bridge overflow mask */
+
+// Timer peripheral register offsets
+#define XV_HDMIRX_TMR_BASE                          (2*64)
+#define XV_HDMIRX_TMR_ID_OFFSET                     ((XV_HDMIRX_TMR_BASE)+(0*4))    /**< TMR Identification register offset */
+#define XV_HDMIRX_TMR_CTRL_OFFSET                   ((XV_HDMIRX_TMR_BASE)+(1*4))    /**< TMR Control register offset */
+#define XV_HDMIRX_TMR_CTRL_SET_OFFSET               ((XV_HDMIRX_TMR_BASE)+(2*4))    /**< TMR Control Register Set offset */
+#define XV_HDMIRX_TMR_CTRL_CLR_OFFSET               ((XV_HDMIRX_TMR_BASE)+(3*4))    /**< TMR Control Register Clear offset */
+#define XV_HDMIRX_TMR_STA_OFFSET                        ((XV_HDMIRX_TMR_BASE)+(4*4))    /**< TMR Status Register offset */
+#define XV_HDMIRX_TMR_CNT_OFFSET                        ((XV_HDMIRX_TMR_BASE)+(5*4))    /**< TMR Counter Register offset */
+
+// Timer peripheral Control register masks
+#define XV_HDMIRX_TMR_CTRL_RUN_MASK                 (1<<0)  /**< TMR Control Run mask */
+#define XV_HDMIRX_TMR_CTRL_IE_MASK                  (1<<1)  /**< TMR Control Interrupt Enable mask */
+
+// Timer peripheral Status register masks
+#define XV_HDMIRX_TMR_STA_IRQ_MASK                  (1<<0)  /**< TMR Status Interrupt mask */
+#define XV_HDMIRX_TMR_STA_CNT_EVT_MASK              (1<<1)  /**< TMR Status counter Event mask */
+
+// Video Timing Detector (VTD) peripheral register offsets.
+#define XV_HDMIRX_VTD_BASE                          (3*64)
+#define XV_HDMIRX_VTD_ID_OFFSET                     ((XV_HDMIRX_VTD_BASE)+(0*4))    /**< VTD Identification Register offset */
+#define XV_HDMIRX_VTD_CTRL_OFFSET                   ((XV_HDMIRX_VTD_BASE)+(1*4))    /**< VTD Control Register offset */
+#define XV_HDMIRX_VTD_CTRL_SET_OFFSET               ((XV_HDMIRX_VTD_BASE)+(2*4))    /**< VTD Control Set Register offset */
+#define XV_HDMIRX_VTD_CTRL_CLR_OFFSET               ((XV_HDMIRX_VTD_BASE)+(3*4))    /**< VTD Control Clear Register offset */
+#define XV_HDMIRX_VTD_STA_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(4*4))    /**< VTD Status Register offset */
+#define XV_HDMIRX_VTD_TOT_PIX_OFFSET                    ((XV_HDMIRX_VTD_BASE)+(5*4))    /**< VTD Total Pixels Register offset */
+#define XV_HDMIRX_VTD_ACT_PIX_OFFSET                    ((XV_HDMIRX_VTD_BASE)+(6*4))    /**< VTD Active Pixels Register offset */
+#define XV_HDMIRX_VTD_TOT_LIN_OFFSET                    ((XV_HDMIRX_VTD_BASE)+(7*4))    /**< VTD Total Lines Register offset */
+#define XV_HDMIRX_VTD_ACT_LIN_OFFSET                    ((XV_HDMIRX_VTD_BASE)+(8*4))    /**< VTD Active Lines Register offset */
+#define XV_HDMIRX_VTD_VSW_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(9*4))    /**< VTD Vertical Sync Width Register offset */
+#define XV_HDMIRX_VTD_HSW_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(10*4))   /**< VTD Horizontal Sync Width Register offset */
+#define XV_HDMIRX_VTD_VFP_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(11*4))   /**< VTD Vertical Front Porch Register offset */
+#define XV_HDMIRX_VTD_VBP_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(12*4))   /**< VTD Vertical Back Porch Register offset */
+#define XV_HDMIRX_VTD_HFP_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(13*4))   /**< VTD Horizontal Front Porch Register offset */
+#define XV_HDMIRX_VTD_HBP_OFFSET                        ((XV_HDMIRX_VTD_BASE)+(14*4))   /**< VTD Horizontal Back Porch Register offset */
+
+// Video timing detector peripheral Control register masks and shift
+#define XV_HDMIRX_VTD_CTRL_RUN_MASK                 (1<<0)  	/**< VTD Control Run mask */
+#define XV_HDMIRX_VTD_CTRL_IE_MASK                  (1<<1)  	/**< VTD Control Interrupt Enable mask */
+#define XV_HDMIRX_VTD_CTRL_FIELD_POL_MASK           (1<<2)  	/**< VTD Control field polarity mask */
+#define XV_HDMIRX_VTD_CTRL_SYNC_LOSS_MASK           (1<<3)    /**< VTD Control field polarity mask */
+#define XV_HDMIRX_VTD_CTRL_TIMEBASE_SHIFT          	8      		/**< VTD Control timebase shift */
+#define XV_HDMIRX_VTD_CTRL_TIMERBASE_MASK          	0xffffff    /**< VTD Control timebase mask */
+
+// Video timing detector peripheral Status register masks
+#define XV_HDMIRX_VTD_STA_IRQ_MASK                  (1<<0)  /**< VTD Status Interrupt mask */
+#define XV_HDMIRX_VTD_STA_TIMEBASE_EVT_MASK        	(1<<1)  /**< VTD Status timebase event mask */
+#define XV_HDMIRX_VTD_STA_VS_POL_MASK               (1<<3)  /**< VTD Status Vsync Polarity mask */
+#define XV_HDMIRX_VTD_STA_HS_POL_MASK               (1<<4)  /**< VTD Status Hsync Polarity mask */
+#define XV_HDMIRX_VTD_STA_FMT_MASK                  (1<<5)  /**< VTD Status Format mask */
+#define XV_HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK        (1<<6)  /**< VTD Status Sync Loss mask */
+
+// DDC (Display Data Channel) peripheral register offsets.
+#define XV_HDMIRX_DDC_BASE                          (4*64)
+#define XV_HDMIRX_DDC_ID_OFFSET                     ((XV_HDMIRX_DDC_BASE)+(0*4))    /**< DDC Identification Register offset */
+#define XV_HDMIRX_DDC_CTRL_OFFSET                   ((XV_HDMIRX_DDC_BASE)+(1*4))    /**< DDC Control Register offset */
+#define XV_HDMIRX_DDC_CTRL_SET_OFFSET               ((XV_HDMIRX_DDC_BASE)+(2*4))    /**< DDC Control Register Set offset */
+#define XV_HDMIRX_DDC_CTRL_CLR_OFFSET               ((XV_HDMIRX_DDC_BASE)+(3*4))    /**< DDC Control Register Clear offset */
+#define XV_HDMIRX_DDC_STA_OFFSET                    ((XV_HDMIRX_DDC_BASE)+(4*4))    /**< DDC Status Register offset */
+#define XV_HDMIRX_DDC_EDID_STA_OFFSET               ((XV_HDMIRX_DDC_BASE)+(5*4))    /**< DDC EDID Status Register offset */
+#define XV_HDMIRX_DDC_HDCP_STA_OFFSET               ((XV_HDMIRX_DDC_BASE)+(6*4))    /**< DDC HDCP Status Register offset */
+#define XV_HDMIRX_DDC_EDID_SP_OFFSET                ((XV_HDMIRX_DDC_BASE)+(8*4))    /**< DDC Read EDID segment pointer offset */
+#define XV_HDMIRX_DDC_EDID_WP_OFFSET                ((XV_HDMIRX_DDC_BASE)+(9*4))    /**< DDC Read EDID write pointer offset */
+#define XV_HDMIRX_DDC_EDID_RP_OFFSET                ((XV_HDMIRX_DDC_BASE)+(10*4))   /**< DDC Read EDID read pointer offset */
+#define XV_HDMIRX_DDC_EDID_DATA_OFFSET              ((XV_HDMIRX_DDC_BASE)+(11*4))   /**< DDC Read EDID data offset */
+#define XV_HDMIRX_DDC_HDCP_ADDRESS_OFFSET           ((XV_HDMIRX_DDC_BASE)+(12*4))   /**< DDC Read HDCP address offset */
+#define XV_HDMIRX_DDC_HDCP_DATA_OFFSET              ((XV_HDMIRX_DDC_BASE)+(13*4))   /**< DDC Read HDCP data offset */
+
+// DDC peripheral Control register masks
+#define XV_HDMIRX_DDC_CTRL_RUN_MASK                 (1<<0)  /**< DDC Control Run mask */
+#define XV_HDMIRX_DDC_CTRL_IE_MASK                  (1<<1)  /**< DDC Control Interrupt enable mask */
+#define XV_HDMIRX_DDC_CTRL_EDID_EN_MASK             (1<<2)  /**< DDC Control EDID enable mask */
+#define XV_HDMIRX_DDC_CTRL_SCDC_EN_MASK             (1<<3)  /**< DDC Control SCDC enable mask */
+#define XV_HDMIRX_DDC_CTRL_HDCP_EN_MASK             (1<<4)  /**< DDC Control HDCP enable mask */
+#define XV_HDMIRX_DDC_CTRL_SCDC_CLR_MASK            (1<<5)  /**< DDC Control SCDC clear mask */
+#define XV_HDMIRX_DDC_CTRL_WMSG_CLR_MASK            (1<<6)  /**< DDC Control write message clear mask */
+#define XV_HDMIRX_DDC_CTRL_RMSG_CLR_MASK            (1<<7)  /**< DDC Control read message clear mask */
+#define XV_HDMIRX_DDC_CTRL_HDCP_MODE_MASK           (1<<8)  /**< DDC Control HDCP mode mask */
+
+// DDC peripheral Status register masks
+#define XV_HDMIRX_DDC_STA_IRQ_MASK                  (1<<0)  /**< DDC Status Interrupt mask */
+#define XV_HDMIRX_DDC_STA_EVT_MASK                  (1<<1)  /**< DDC Status Event mask */
+#define XV_HDMIRX_DDC_STA_BUSY_MASK                 (1<<2)  /**< DDC Status Busy mask */
+#define XV_HDMIRX_DDC_STA_SCL_MASK                  (1<<3)  /**< DDC Status state of the SCL input mask */
+#define XV_HDMIRX_DDC_STA_SDA_MASK                  (1<<4)  /**< DDC Status state of the SDA input mask */
+#define XV_HDMIRX_DDC_STA_HDCP_AKSV_EVT_MASK        (1<<5)  /**< DDC Status HDCP AKSV event mask */
+#define XV_HDMIRX_DDC_STA_HDCP_WMSG_NEW_EVT_MASK    (1<<6)  /**< DDC Status HDCP write message buffer new event mask */
+#define XV_HDMIRX_DDC_STA_HDCP_RMSG_END_EVT_MASK    (1<<7)  /**< DDC Status HDCP read message buffer end event mask */
+#define XV_HDMIRX_DDC_STA_HDCP_RMSG_NC_EVT_MASK     (1<<8)  /**< DDC Status HDCP read message buffer not completed event mask */
+#define XV_HDMIRX_DDC_STA_HDCP_1_PROT_MASK          (1<<9)  /**< DDC Status HDCP 1.4 protocol flag */
+#define XV_HDMIRX_DDC_STA_HDCP_2_PROT_MASK          (1<<10) /**< DDC Status HDCP 2.2 protocol flag */
+#define XV_HDMIRX_DDC_STA_HDCP_1_PROT_EVT_MASK      (1<<11) /**< DDC Status HDCP 1.4 protocol event flag */
+#define XV_HDMIRX_DDC_STA_HDCP_2_PROT_EVT_MASK      (1<<12) /**< DDC Status HDCP 2.2 protocol event flag */
+#define XV_HDMIRX_DDC_STA_EDID_WORDS_SHIFT          0       /**< DDC Status EDID words shift */
+#define XV_HDMIRX_DDC_STA_EDID_WORDS_MASK           0xFFFF  /**< DDC Status EDID words mask */
+#define XV_HDMIRX_DDC_STA_HDCP_WMSG_WORDS_MASK      0x7FF   /**< DDC Status HDCP 2.2 write message buffer words mask */
+#define XV_HDMIRX_DDC_STA_HDCP_WMSG_WORDS_SHIFT     0       /**< DDC Status HDCP 2.2 write message buffer words shift */
+#define XV_HDMIRX_DDC_STA_HDCP_WMSG_EP_MASK         (1<<11) /**< DDC Status HDCP 2.2 write message buffer empty mask */
+#define XV_HDMIRX_DDC_STA_HDCP_RMSG_WORDS_MASK      0x7FF   /**< DDC Status HDCP 2.2 read message buffer words mask */
+#define XV_HDMIRX_DDC_STA_HDCP_RMSG_WORDS_SHIFT     16      /**< DDC Status HDCP 2.2 read message buffer words shift */
+#define XV_HDMIRX_DDC_STA_HDCP_RMSG_EP_MASK         (1<<27) /**< DDC Status HDCP 2.2 read message buffer empty mask */
+
+// Auxiliary (AUX) peripheral register offsets.
+#define XV_HDMIRX_AUX_BASE                          (5*64)
+#define XV_HDMIRX_AUX_ID_OFFSET                     ((XV_HDMIRX_AUX_BASE)+(0*4))    /**< AUX Identification Register offset */
+#define XV_HDMIRX_AUX_CTRL_OFFSET                   ((XV_HDMIRX_AUX_BASE)+(1*4))    /**< AUX Control Register offset */
+#define XV_HDMIRX_AUX_CTRL_SET_OFFSET               ((XV_HDMIRX_AUX_BASE)+(2*4))    /**< AUX Control Register Set offset */
+#define XV_HDMIRX_AUX_CTRL_CLR_OFFSET               ((XV_HDMIRX_AUX_BASE)+(3*4))    /**< AUX Control Register Clear offset */
+#define XV_HDMIRX_AUX_STA_OFFSET                        ((XV_HDMIRX_AUX_BASE)+(4*4))    /**< AUX Status Register offset */
+#define XV_HDMIRX_AUX_DAT_OFFSET                        ((XV_HDMIRX_AUX_BASE)+(5*4))    /**< AUX Data Register offset */
+
+// AUX peripheral Control register masks
+#define XV_HDMIRX_AUX_CTRL_RUN_MASK                 (1<<0)  /**< AUX Control Run mask */
+#define XV_HDMIRX_AUX_CTRL_IE_MASK                  (1<<1)  /**< AUX Control Interrupt Enable mask */
+
+// AUX peripheral Status register masks and shifts
+#define XV_HDMIRX_AUX_STA_IRQ_MASK                  (1<<0)  /**< AUX Status Interrupt mask */
+#define XV_HDMIRX_AUX_STA_NEW_MASK                  (1<<1)  /**< AUX Status New Packet mask */
+#define XV_HDMIRX_AUX_STA_ERR_MASK					(1<<2)	/**< AUX Status New Packet mask */
+#define XV_HDMIRX_AUX_STA_AVI_MASK					(1<<3)	/**< AUX Status AVI infoframe mask */
+#define XV_HDMIRX_AUX_STA_GCP_MASK					(1<<4)	/**< AUX Status General control packet mask */
+#define XV_HDMIRX_AUX_STA_FIFO_EP_MASK              (1<<5)  /**< AUX Status FIFO Empty mask */
+#define XV_HDMIRX_AUX_STA_FIFO_FL_MASK              (1<<6)  /**< AUX Status FIFO Full mask */
+#define XV_HDMIRX_AUX_STA_GCP_CD_EVT_MASK			(1<<25) /**< AUX Status GCP ColorDepth mask */
+#define XV_HDMIRX_AUX_STA_GCP_AVMUTE_MASK           (1<<31) /**< AUX Status GCP avmute mask */
+#define XV_HDMIRX_AUX_STA_NEW_PKTS_MASK             0x1F    /**< AUX Status New Packets mask */
+#define XV_HDMIRX_AUX_STA_AVI_CS_MASK               0x03    /**< AUX Status AVI colorspace mask */
+#define XV_HDMIRX_AUX_STA_AVI_VIC_MASK              0x7F    /**< AUX Status AVI VIC mask */
+#define XV_HDMIRX_AUX_STA_GCP_CD_MASK               0x03    /**< AUX Status GCP colordepth mask */
+#define XV_HDMIRX_AUX_STA_GCP_PP_MASK               0x07    /**< AUX Status GCP pixel phase mask */
+#define XV_HDMIRX_AUX_STA_NEW_PKTS_SHIFT                8       /**< AUX Status New Packets Shift */
+#define XV_HDMIRX_AUX_STA_AVI_CS_SHIFT              16      /**< AUX Status AVI colorspace Shift */
+#define XV_HDMIRX_AUX_STA_AVI_VIC_SHIFT             18      /**< AUX Status AVI VIC Shift */
+#define XV_HDMIRX_AUX_STA_GCP_CD_SHIFT              26      /**< AUX Status GCP colordepth Shift */
+#define XV_HDMIRX_AUX_STA_GCP_PP_SHIFT              28      /**< AUX Status GCP pixel phase Shift */
+
+
+// Audio (AUD) peripheral register offsets.
+#define XV_HDMIRX_AUD_BASE                          (6*64)
+#define XV_HDMIRX_AUD_ID_OFFSET                     ((XV_HDMIRX_AUD_BASE)+(0*4))    /**< AUD Identification Register offset */
+#define XV_HDMIRX_AUD_CTRL_OFFSET                   ((XV_HDMIRX_AUD_BASE)+(1*4))    /**< AUD Control Register offset */
+#define XV_HDMIRX_AUD_CTRL_SET_OFFSET               ((XV_HDMIRX_AUD_BASE)+(2*4))    /**< AUD Control Register Set offset */
+#define XV_HDMIRX_AUD_CTRL_CLR_OFFSET               ((XV_HDMIRX_AUD_BASE)+(3*4))    /**< AUD Control Register Clear offset */
+#define XV_HDMIRX_AUD_STA_OFFSET                        ((XV_HDMIRX_AUD_BASE)+(4*4))    /**< AUD Status Register offset */
+#define XV_HDMIRX_AUD_CTS_OFFSET                        ((XV_HDMIRX_AUD_BASE)+(5*4))    /**< AUD CTS Register offset */
+#define XV_HDMIRX_AUD_N_OFFSET                      ((XV_HDMIRX_AUD_BASE)+(6*4))    /**< AUD N Register offset */
+
+// Audio peripheral Control register masks
+#define XV_HDMIRX_AUD_CTRL_RUN_MASK                 (1<<0)  /**< AUD Control Run mask */
+#define XV_HDMIRX_AUD_CTRL_IE_MASK                  (1<<1)  /**< AUD Control Interrupt Enable mask */
+
+// AUD peripheral Status register masks and shift
+#define XV_HDMIRX_AUD_STA_IRQ_MASK                  (1<<0)  /**< AUD Status Interrupt mask */
+#define XV_HDMIRX_AUD_STA_ACT_EVT_MASK              (1<<1)  /**< AUD Status Event mask */
+#define XV_HDMIRX_AUD_STA_CH_EVT_MASK               (1<<2)  /**< AUD Status Event mask */
+#define XV_HDMIRX_AUD_STA_ACT_MASK                  (1<<3)  /**< AUD Status Active mask */
+#define XV_HDMIRX_AUD_STA_AUD_CH_MASK               0x1F    /**< AUD Status Audio channel mask */
+#define XV_HDMIRX_AUD_STA_AUD_CH_SHIFT              8       /**< AUD Status Audio channel Shift */
+#define XV_HDMIRX_AUD_STA_AUD_FMT_MASK              0x07    /**< AUD Status Audio Format mask */
+#define XV_HDMIRX_AUD_STA_AUD_FMT_SHIFT             13      /**< AUD Status Audio Format Shift */
+
+
+// Link Status (LNKSTA) peripheral register offsets.
+#define XV_HDMIRX_LNKSTA_BASE                       (7*64)
+#define XV_HDMIRX_LNKSTA_ID_OFFSET                  ((XV_HDMIRX_LNKSTA_BASE)+(0*4)) /**< LNKSTA Identification Register offset */
+#define XV_HDMIRX_LNKSTA_CTRL_OFFSET                    ((XV_HDMIRX_LNKSTA_BASE)+(1*4)) /**< LNKSTA Control Register offset */
+#define XV_HDMIRX_LNKSTA_CTRL_SET_OFFSET                ((XV_HDMIRX_LNKSTA_BASE)+(2*4)) /**< LNKSTA Control Register Set offset */
+#define XV_HDMIRX_LNKSTA_CTRL_CLR_OFFSET                ((XV_HDMIRX_LNKSTA_BASE)+(3*4)) /**< LNKSTA Control Register Clear offset */
+#define XV_HDMIRX_LNKSTA_STA_OFFSET                 ((XV_HDMIRX_LNKSTA_BASE)+(4*4)) /**< LNKSTA Status Register offset */
+#define XV_HDMIRX_LNKSTA_LNK_ERR0_OFFSET                ((XV_HDMIRX_LNKSTA_BASE)+(5*4)) /**< LNKSTA Link Error Counter Channel 0 Register offset */
+#define XV_HDMIRX_LNKSTA_LNK_ERR1_OFFSET                ((XV_HDMIRX_LNKSTA_BASE)+(6*4)) /**< LNKSTA Link Error Counter Channel 1 Register offset */
+#define XV_HDMIRX_LNKSTA_LNK_ERR2_OFFSET                ((XV_HDMIRX_LNKSTA_BASE)+(7*4)) /**< LNKSTA Link Error Counter Channel 2 Register offset */
+
+// Link Status (LNKSTA) peripheral Control register masks
+#define XV_HDMIRX_LNKSTA_CTRL_RUN_MASK              (1<<0)  /**< LNKSTA Control Run mask */
+#define XV_HDMIRX_LNKSTA_CTRL_IE_MASK               (1<<1)  /**< LNKSTA Control Interrupt Enable mask */
+#define XV_HDMIRX_LNKSTA_CTRL_ERR_CLR_MASK          (1<<2)  /**< LNKSTA Control Error Clear mask */
+
+// Link Status (LNKSTA) peripheral Status register masks
+#define XV_HDMIRX_LNKSTA_STA_IRQ_MASK               (1<<0)  /**< LNKSTA Status Interrupt mask */
+#define XV_HDMIRX_LNKSTA_STA_ERR_MAX_MASK           (1<<1)  /**< LNKSTA Status Maximum Errors mask */
+
+// Peripheral ID and General shift values.
+#define XV_HDMIRX_SHIFT_16      16  /**< 16 shift value */
+#define XV_HDMIRX_MASK_16       0xFFFF  /**< 16 bit mask value */
+#define XV_HDMIRX_PIO_ID            0x2200  /**< PIO ID */
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/** @name Register access macro definition
+* @{
+*/
+#define XV_HdmiRx_In32  Xil_In32    /**< Input Operations */
+#define XV_HdmiRx_Out32 Xil_Out32   /**< Output Operations */
+
+/*****************************************************************************/
+/**
+*
+* This macro reads a value from a HDMI RX register. A 32 bit read is performed.
+* If the component is implemented in a smaller width, only the least
+* significant data is read from the register. The most significant data
+* will be read as 0.
+*
+* @param    BaseAddress is the base address of the HDMI RX core instance.
+* @param    RegOffset is the register offset of the register (defined at
+*       the top of this file).
+*
+* @return   The 32-bit value of the register.
+*
+* @note     C-style signature:
+*           u32 XV_HdmiRx_ReadReg(UINTPTR BaseAddress, u32 RegOffset)
+*
+******************************************************************************/
+#define XV_HdmiRx_ReadReg(BaseAddress, RegOffset) \
+    XV_HdmiRx_In32((BaseAddress) + (RegOffset))
+
+/*****************************************************************************/
+/**
+*
+* This macro writes a value to a HDMI RX register. A 32 bit write is performed.
+* If the component is implemented in a smaller width, only the least
+* significant data is written.
+*
+* @param    BaseAddress is the base address of the HDMI RX core instance.
+* @param    RegOffset is the register offset of the register (defined at
+*       the top of this file) to be written.
+* @param    Data is the 32-bit value to write into the register.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*           void XV_HdmiRx_WriteReg(UINTPTR BaseAddress, u32 RegOffset, u32 Data)
+*
+******************************************************************************/
+#define XV_HdmiRx_WriteReg(BaseAddress, RegOffset, Data) \
+    XV_HdmiRx_Out32((BaseAddress) + (RegOffset), (u32)(Data))
+/*@}*/
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Declarations ****************************/
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx_intr.c
@@ -0,0 +1,1057 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirx_intr.c
+*
+* This file contains interrupt related functions for Xilinx HDMI RX core.
+* Please see xv_hdmirx.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00  gm, mg 11/03/15 Initial release.
+* 1.01  yh     14/01/16 Set AxisEnable PIO to high when RX stream locked
+* 1.03  MG     18/02/16 Added Link Check callback
+* 1.04  MG     08/03/16 Added pixel clock calculation to HdmiRx_TmrIntrHandler
+* 1.05  MH     08/03/16 Added support for read not complete DDC event
+* 1.06  MG     27/05/16 Updated HdmiRx_VtdIntrHandler
+* 1.07  MG     27/05/16 Updated HdmiRx_TmrIntrHandler
+* 1.08  MG     30/05/16 Fixed issue with pixel clock adjustment for YUV422 colorspace
+* 1.09  MH     26/07/16 Added DDC HDCP protocol event.
+* 1.10  YH     18/08/16 squash unused variable compiler warning
+* 1.11  MG     03/03/17 Updated function HdmiRx_TmrIntrHandler with
+*                           GetVideoPropertiesTries
+* 1.12  YH     22/08/17 Update AudFormat when servicing Aud Interrupt
+* 1.13  MH     31/08/17 Update Reset sequence for Video_Bridge
+* 2.00  EB     16/01/18 Added clearing of XV_HDMIRX_AUX_STA_GCP_CD_EVT flag
+*                           after servicing it
+*       YH     16/11/17 Added bridge overflow interrupt
+*              16/11/17 Update Reset sequence with dedicated reset for
+*                           each clock domain
+*       MMO    08/02/18 Adding proper handling for Sync Loss/Sync Recover
+* 2.10  YH     13/04/18 Fixed a bug in PioIntrHandler
+* 2.20  EB     16/08/18 Replaced TIME_10MS, TIME_16MS, TIME_200MS with
+*                           XV_HdmiRx_GetTime10Ms, XV_HdmiRx_GetTime16Ms
+*                           XV_HdmiRx_GetTime200Ms
+*                       Added TMDS Clock Ratio callback support
+*       YB     15/08/18 Added new cases for HDCP 1.4 & 2.2 protocol events in
+*                           XV_HdmiRx_SetCallback function.
+*                       Updated the HdmiRx_DdcIntrHandler() function.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmirx.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+void HdmiRx_PioIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_TmrIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_VtdIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_DdcIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_AuxIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_AudIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_LinkStatusIntrHandler(XV_HdmiRx *InstancePtr);
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX driver.
+*
+* This handler reads the pending interrupt from PIO, DDC, TIMDET, AUX, AUD
+* and LNKSTA peripherals, determines the source of the interrupts, clears the
+* interrupts and calls callbacks accordingly.
+*
+* The application is responsible for connecting this function to the interrupt
+* system. Application beyond this driver is also responsible for providing
+* callbacks to handle interrupts and installing the callbacks using
+* XV_HdmiRx_SetCallback() during initialization phase. An example delivered
+* with this driver demonstrates how this could be done.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx instance that just
+*       interrupted.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRx_IntrHandler(void *InstancePtr)
+{
+    u32 Data;
+    XV_HdmiRx *HdmiRxPtr = (XV_HdmiRx *)InstancePtr;
+
+    /* Verify arguments */
+    Xil_AssertVoid(HdmiRxPtr != NULL);
+    Xil_AssertVoid(HdmiRxPtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    /* PIO */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_PIO_STA_OFFSET)) & (XV_HDMIRX_PIO_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to PIO handler */
+        HdmiRx_PioIntrHandler(HdmiRxPtr);
+    }
+
+    /* Timer */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_TMR_STA_OFFSET)) & (XV_HDMIRX_TMR_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to PIO handler */
+        HdmiRx_TmrIntrHandler(HdmiRxPtr);
+    }
+
+    /* Video Timing detector */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_VTD_STA_OFFSET)) & (XV_HDMIRX_VTD_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to video timing detector handler */
+        HdmiRx_VtdIntrHandler(HdmiRxPtr);
+    }
+
+    /* DDC */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET)) & (XV_HDMIRX_DDC_STA_IRQ_MASK);
+
+    /* Is the IRQ flag set */
+    if (Data) {
+        /* Jump to DDC handler */
+        HdmiRx_DdcIntrHandler(HdmiRxPtr);
+    }
+
+    /* AUX */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET)) & (XV_HDMIRX_AUX_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to AUX handler */
+        HdmiRx_AuxIntrHandler(HdmiRxPtr);
+    }
+
+    /* Audio */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_AUD_STA_OFFSET)) & (XV_HDMIRX_AUD_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to Audio handler */
+        HdmiRx_AudIntrHandler(HdmiRxPtr);
+    }
+
+    /* Link status */
+    Data = XV_HdmiRx_ReadReg(HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_LNKSTA_STA_OFFSET)) & (XV_HDMIRX_LNKSTA_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to Link Status handler */
+        HdmiRx_LinkStatusIntrHandler(HdmiRxPtr);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                 Callback Function Type
+* -------------------------   -----------------------------------------------
+* (XV_HDMIRX_HANDLER_VTD)         VtdCallback
+* (XV_HDMIRX_HANDLER_AUX)      AuxCallback
+* (XV_HDMIRX_HANDLER_AUD)      AudCallback
+* (XV_HDMIRX_HANDLER_LNKSTA)   LnkStaCallback
+* (XV_HDMIRX_HANDLER_PIO)      PioCallback
+* </pre>
+*
+* @param    InstancePtr is a pointer to the HDMI RX core instance.
+* @param    HandlerType specifies the type of handler.
+* @param    CallbackFunc is the address of the callback function.
+* @param    CallbackRef is a user data item that will be passed to the
+*       callback function when it is invoked.
+*
+* @return
+*       - XST_SUCCESS if callback function installed successfully.
+*       - XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note     Invoking this function for a handler that already has been
+*       installed replaces it with the new handler.
+*
+******************************************************************************/
+int XV_HdmiRx_SetCallback(XV_HdmiRx *InstancePtr,
+		XV_HdmiRx_HandlerType HandlerType,
+		void *CallbackFunc,
+		void *CallbackRef)
+{
+    u32 Status;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(HandlerType >= (XV_HDMIRX_HANDLER_CONNECT));
+    Xil_AssertNonvoid(CallbackFunc != NULL);
+    Xil_AssertNonvoid(CallbackRef != NULL);
+
+    /* Check for handler type */
+    switch (HandlerType) {
+
+        case (XV_HDMIRX_HANDLER_CONNECT):
+            InstancePtr->ConnectCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->ConnectRef = CallbackRef;
+            InstancePtr->IsConnectCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRX_HANDLER_AUX):
+            InstancePtr->AuxCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->AuxRef = CallbackRef;
+            InstancePtr->IsAuxCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRX_HANDLER_AUD):
+            InstancePtr->AudCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->AudRef = CallbackRef;
+            InstancePtr->IsAudCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRX_HANDLER_LNKSTA):
+            InstancePtr->LnkStaCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->LnkStaRef = CallbackRef;
+            InstancePtr->IsLnkStaCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Ddc
+        case (XV_HDMIRX_HANDLER_DDC):
+            InstancePtr->DdcCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->DdcRef = CallbackRef;
+            InstancePtr->IsDdcCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream down
+        case (XV_HDMIRX_HANDLER_STREAM_DOWN):
+            InstancePtr->StreamDownCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->StreamDownRef = CallbackRef;
+            InstancePtr->IsStreamDownCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream Init
+        case (XV_HDMIRX_HANDLER_STREAM_INIT):
+            InstancePtr->StreamInitCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->StreamInitRef = CallbackRef;
+            InstancePtr->IsStreamInitCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream up
+        case (XV_HDMIRX_HANDLER_STREAM_UP):
+            InstancePtr->StreamUpCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->StreamUpRef = CallbackRef;
+            InstancePtr->IsStreamUpCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP
+        case (XV_HDMIRX_HANDLER_HDCP):
+            InstancePtr->HdcpCallback = (XV_HdmiRx_HdcpCallback)CallbackFunc;
+            InstancePtr->HdcpRef = CallbackRef;
+            InstancePtr->IsHdcpCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP 1.4 Event
+        case (XV_HDMIRX_HANDLER_DDC_HDCP_14_PROT):
+            InstancePtr->Hdcp14ProtEvtCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->Hdcp14ProtEvtRef = CallbackRef;
+            InstancePtr->IsHdcp14ProtEvtCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP 2.2 Event
+        case (XV_HDMIRX_HANDLER_DDC_HDCP_22_PROT):
+            InstancePtr->Hdcp22ProtEvtCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->Hdcp22ProtEvtRef = CallbackRef;
+            InstancePtr->IsHdcp22ProtEvtCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRX_HANDLER_LINK_ERROR):
+            InstancePtr->LinkErrorCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->LinkErrorRef = CallbackRef;
+            InstancePtr->IsLinkErrorCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Bridge FIFO Overflow
+        case (XV_HDMIRX_HANDLER_BRDG_OVERFLOW):
+            InstancePtr->BrdgOverflowCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->BrdgOverflowRef = CallbackRef;
+            InstancePtr->IsBrdgOverflowCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Sync Loss
+        case (XV_HDMIRX_HANDLER_SYNC_LOSS):
+            InstancePtr->SyncLossCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->SyncLossRef = CallbackRef;
+            InstancePtr->IsSyncLossCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Mode
+        case (XV_HDMIRX_HANDLER_MODE):
+            InstancePtr->ModeCallback = (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->ModeRef = CallbackRef;
+            InstancePtr->IsModeCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // TMDS clock ratio
+        case (XV_HDMIRX_HANDLER_TMDS_CLK_RATIO):
+            InstancePtr->TmdsClkRatioCallback =
+                                  (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->TmdsClkRatioRef = CallbackRef;
+            InstancePtr->IsTmdsClkRatioCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Vic Error
+        case (XV_HDMIRX_HANDLER_VIC_ERROR):
+            InstancePtr->VicErrorCallback =
+                                  (XV_HdmiRx_Callback)CallbackFunc;
+            InstancePtr->VicErrorRef = CallbackRef;
+            InstancePtr->IsVicErrorCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        default:
+            Status = (XST_INVALID_PARAM);
+            break;
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX Timing Detector
+* (TIMDET) peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_VtdIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    u32 Status;
+    XVidC_VideoMode DecodedVmId = 0;
+
+    /* Read Video timing detector Status register */
+    Status = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress,
+		    (XV_HDMIRX_VTD_STA_OFFSET));
+
+    /* Check for time base event */
+    if ((Status) & (XV_HDMIRX_VTD_STA_TIMEBASE_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress,
+        		(XV_HDMIRX_VTD_STA_OFFSET),
+			(XV_HDMIRX_VTD_STA_TIMEBASE_EVT_MASK));
+
+        // Check if we are in lock state
+        if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_LOCK) {
+
+            // Read video timing
+            Status = XV_HdmiRx_GetVideoTiming(InstancePtr);
+
+            if (Status == XST_SUCCESS) {
+                if (InstancePtr->Stream.Vic != 0) {
+                    DecodedVmId = XV_HdmiRx_LookupVmId(InstancePtr->Stream.Vic);
+
+                    if (DecodedVmId != InstancePtr->Stream.Video.VmId &&
+                		    !(DecodedVmId == XVIDC_VM_NOT_SUPPORTED &&
+                				    InstancePtr->Stream.Video.VmId ==
+                						    XVIDC_VM_CUSTOM)) {
+                        /* Call VIC error callback */
+                        if (InstancePtr->VicErrorCallback) {
+                        	InstancePtr->VicErrorCallback(
+                        			InstancePtr->VicErrorRef);
+                        }
+                    }
+                }
+
+                // Enable AXI Stream output
+                XV_HdmiRx_AxisEnable(InstancePtr, (TRUE));
+
+                // Set stream status to up
+                InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_UP;
+
+                // Set stream sync status to est
+                InstancePtr->Stream.SyncStatus = XV_HDMIRX_SYNCSTAT_SYNC_EST;
+
+                // Enable sync loss
+                //XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress,
+                //  (XV_HDMIRX_VTD_CTRL_SET_OFFSET), (XV_HDMIRX_VTD_CTRL_SYNC_LOSS_MASK));
+
+                // Call stream up callback
+                if (InstancePtr->IsStreamUpCallbackSet) {
+                    InstancePtr->StreamUpCallback(InstancePtr->StreamUpRef);
+                }
+            }
+        }
+
+        // Check if we are in stream up state
+        else if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_UP) {
+
+            // Read video timing
+            Status = XV_HdmiRx_GetVideoTiming(InstancePtr);
+
+            if (Status != XST_SUCCESS) {
+                // Disable sync loss
+                //XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress,
+                //  (XV_HDMIRX_VTD_CTRL_CLR_OFFSET), (XV_HDMIRX_VTD_CTRL_SYNC_LOSS_MASK));
+
+                // Set stream status to up
+                InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_LOCK;
+
+            } else if (InstancePtr->Stream.SyncStatus == XV_HDMIRX_SYNCSTAT_SYNC_LOSS) {
+            	// Sync Est/Recover Flag
+            	InstancePtr->Stream.SyncStatus = XV_HDMIRX_SYNCSTAT_SYNC_EST;
+
+				// Call sync lost callback
+				if (InstancePtr->IsSyncLossCallbackSet) {
+					InstancePtr->SyncLossCallback(InstancePtr->SyncLossRef);
+				}
+            }
+        }
+
+    }
+
+    /* Check for sync loss event */
+    else if ((Status) & (XV_HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_VTD_STA_OFFSET), (XV_HDMIRX_VTD_STA_SYNC_LOSS_EVT_MASK));
+
+        if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_UP) {
+        	// Enable the Stream Up + Sync Loss Flag
+        	InstancePtr->Stream.SyncStatus = XV_HDMIRX_SYNCSTAT_SYNC_LOSS;
+
+			// Call sync lost callback
+			if (InstancePtr->IsSyncLossCallbackSet) {
+				InstancePtr->SyncLossCallback(InstancePtr->SyncLossRef);
+			}
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX DDC peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_DdcIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    u32 Status;
+
+    /* Read Status register */
+    Status = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET));
+
+    /* Check for HDCP write event */
+    if ((Status) & (XV_HDMIRX_DDC_STA_HDCP_WMSG_NEW_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET), (XV_HDMIRX_DDC_STA_HDCP_WMSG_NEW_EVT_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsHdcpCallbackSet) {
+            InstancePtr->HdcpCallback(InstancePtr->HdcpRef, XV_HDMIRX_DDC_STA_HDCP_WMSG_NEW_EVT_MASK);
+        }
+    }
+
+    /* Check for HDCP read event */
+    if ((Status) & (XV_HDMIRX_DDC_STA_HDCP_RMSG_END_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET), (XV_HDMIRX_DDC_STA_HDCP_RMSG_END_EVT_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsHdcpCallbackSet) {
+            InstancePtr->HdcpCallback(InstancePtr->HdcpRef, XV_HDMIRX_DDC_STA_HDCP_RMSG_END_EVT_MASK);
+        }
+    }
+
+    /* Check for HDCP read not complete event */
+    if ((Status) & (XV_HDMIRX_DDC_STA_HDCP_RMSG_NC_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET), (XV_HDMIRX_DDC_STA_HDCP_RMSG_NC_EVT_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsHdcpCallbackSet) {
+            InstancePtr->HdcpCallback(InstancePtr->HdcpRef, XV_HDMIRX_DDC_STA_HDCP_RMSG_NC_EVT_MASK);
+        }
+    }
+
+    /* Check for HDCP 1.4 Aksv event */
+    if ((Status) & (XV_HDMIRX_DDC_STA_HDCP_AKSV_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET), (XV_HDMIRX_DDC_STA_HDCP_AKSV_EVT_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsHdcpCallbackSet) {
+            InstancePtr->HdcpCallback(InstancePtr->HdcpRef, XV_HDMIRX_DDC_STA_HDCP_AKSV_EVT_MASK);
+        }
+    }
+
+    /* Check for HDCP 1.4 protocol event */
+    if ((Status) & (XV_HDMIRX_DDC_STA_HDCP_1_PROT_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET), (XV_HDMIRX_DDC_STA_HDCP_1_PROT_EVT_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsHdcp14ProtEvtCallbackSet) {
+            InstancePtr->Hdcp14ProtEvtCallback(InstancePtr->Hdcp14ProtEvtRef);
+        }
+    }
+
+    /* Check for HDCP 2.2 protocol event */
+    if ((Status) & (XV_HDMIRX_DDC_STA_HDCP_2_PROT_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET), (XV_HDMIRX_DDC_STA_HDCP_2_PROT_EVT_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsHdcp22ProtEvtCallbackSet) {
+            InstancePtr->Hdcp22ProtEvtCallback(InstancePtr->Hdcp22ProtEvtRef);
+        }
+    }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX PIO peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_PioIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    u32 Event;
+    u32 Data;
+
+    /* Read PIO IN Event register.*/
+    Event = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_IN_EVT_OFFSET));
+
+    /* Clear event flags */
+    XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_IN_EVT_OFFSET), (Event));
+
+    /* Read data */
+    Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_PIO_IN_OFFSET));
+
+    // Cable detect event has occurred
+    if ((Event) & (XV_HDMIRX_PIO_IN_DET_MASK)) {
+
+        // Cable is connected
+        if ((Data) & (XV_HDMIRX_PIO_IN_DET_MASK)) {
+            // Set connected flag
+            InstancePtr->Stream.IsConnected = (TRUE);
+        }
+
+        // Cable is disconnected
+        else {
+            // Clear connected flag
+            InstancePtr->Stream.IsConnected = (FALSE);
+
+            // Clear SCDC variables
+            XV_HdmiRx_DdcScdcClear(InstancePtr);
+        }
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsConnectCallbackSet) {
+            InstancePtr->ConnectCallback(InstancePtr->ConnectRef);
+        }
+    }
+
+    // Link ready event has occurred
+    if ((Event) & (XV_HDMIRX_PIO_IN_LNK_RDY_MASK)) {
+
+    // Set stream status to idle
+        InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_IDLE;            // The stream idle
+
+        // Load timer
+        XV_HdmiRx_TmrStart(InstancePtr,
+			XV_HdmiRx_GetTime10Ms(InstancePtr)); // 10 ms
+    }
+
+    // Video ready event has occurred
+    if ((Event) & (XV_HDMIRX_PIO_IN_VID_RDY_MASK)) {
+
+        // Ready
+        if ((Data) & (XV_HDMIRX_PIO_IN_VID_RDY_MASK)) {
+
+            // Check the previous state
+            // The link can only change to up when the previous state was init
+            // Else there was a glitch on the video ready input
+            if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_INIT) {
+
+				/* Toggle video reset for HDMI RX core */
+				XV_HdmiRx_INT_VRST(InstancePtr, TRUE);
+				XV_HdmiRx_INT_VRST(InstancePtr, FALSE);
+
+				/* Toggle bridge reset */
+				XV_HdmiRx_EXT_VRST(InstancePtr, TRUE);
+				XV_HdmiRx_EXT_SYSRST(InstancePtr, TRUE);
+				XV_HdmiRx_EXT_VRST(InstancePtr, FALSE);
+				XV_HdmiRx_EXT_SYSRST(InstancePtr, FALSE);
+
+				// Set stream status to arm
+                InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_ARM;         // The stream is armed
+
+                // Load timer - 200 ms (one UHD frame is 40 ms, 5 frames)
+                XV_HdmiRx_TmrStart(InstancePtr,
+				XV_HdmiRx_GetTime200Ms(InstancePtr));
+            }
+        }
+
+        // Stream down
+        else {
+			/* Assert HDMI RX core resets */
+			XV_HdmiRx_INT_VRST(InstancePtr, TRUE);
+			XV_HdmiRx_INT_LRST(InstancePtr, TRUE);
+
+            /* Clear variables */
+            XV_HdmiRx_Clear(InstancePtr);
+
+            // Disable aux and audio peripheral
+            // At this state the link clock is not stable.
+            // Therefore these two peripheral are disabled to prevent any glitches.
+            XV_HdmiRx_AuxDisable(InstancePtr);
+            XV_HdmiRx_AudioDisable(InstancePtr);
+
+            /* Disable VTD */
+            XV_HdmiRx_VtdDisable(InstancePtr);
+
+            // Disable link
+            XV_HdmiRx_LinkEnable(InstancePtr, (FALSE));
+
+            // Disable video
+            // MH AI: Don't reset bridge when clock is not stable
+            XV_HdmiRx_VideoEnable(InstancePtr, (TRUE));
+
+            XV_HdmiRx_AxisEnable(InstancePtr, (FALSE));
+
+            // Set stream status to down
+            InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_DOWN;
+
+            // Disable sync loss
+            XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress,
+                (XV_HDMIRX_VTD_CTRL_CLR_OFFSET), (XV_HDMIRX_VTD_CTRL_SYNC_LOSS_MASK));
+
+            // Call stream down callback
+            if (InstancePtr->IsStreamDownCallbackSet) {
+                InstancePtr->StreamDownCallback(InstancePtr->StreamDownRef);
+            }
+        }
+    }
+
+    // SCDC Scrambler Enable
+    if ((Event) & (XV_HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK)) {
+
+        // Enable scrambler
+        if ((Data) & (XV_HDMIRX_PIO_IN_SCDC_SCRAMBLER_ENABLE_MASK)) {
+            XV_HdmiRx_SetScrambler(InstancePtr, (TRUE));
+        }
+
+        // Disable scrambler
+        else {
+            XV_HdmiRx_SetScrambler(InstancePtr, (FALSE));
+        }
+    }
+
+    // Mode
+    if ((Event) & (XV_HDMIRX_PIO_IN_MODE_MASK)) {
+
+        // HDMI Mode
+        if ((Data) & (XV_HDMIRX_PIO_IN_MODE_MASK)) {
+            InstancePtr->Stream.IsHdmi = (TRUE);
+        }
+
+        // DVI Mode
+        else {
+            InstancePtr->Stream.IsHdmi = (FALSE);
+        }
+
+        if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_UP) {
+
+            /* Clear variables */
+            XV_HdmiRx_Clear(InstancePtr);
+
+        	// Set stream status to idle
+            InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_IDLE;
+
+            // Load timer
+            XV_HdmiRx_TmrStart(InstancePtr,
+			XV_HdmiRx_GetTime10Ms(InstancePtr)); // 10 ms
+        }
+
+        // Call mode callback
+        if (InstancePtr->IsModeCallbackSet) {
+            InstancePtr->ModeCallback(InstancePtr->ModeRef);
+        }
+    }
+
+    // TMDS clock ratio
+    if ((Event) & (XV_HDMIRX_PIO_IN_SCDC_TMDS_CLOCK_RATIO_MASK)) {
+        // Call TMDS Ratio callback
+        if (InstancePtr->IsTmdsClkRatioCallbackSet) {
+            InstancePtr->TmdsClkRatioCallback(InstancePtr->TmdsClkRatioRef);
+        }
+    }
+
+    /* Bridge Overflow event has occurred */
+    if ((Event) & (XV_HDMIRX_PIO_IN_BRDG_OVERFLOW_MASK)) {
+        // Check if user callback has been registered
+        if (InstancePtr->IsBrdgOverflowCallbackSet) {
+            InstancePtr->BrdgOverflowCallback(InstancePtr->BrdgOverflowRef);
+        }
+    }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX TMR peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_TmrIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    u32 Status;
+
+    /* Read Status register */
+    Status = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_TMR_STA_OFFSET));
+
+    /* Check for counter event */
+    if ((Status) & (XV_HDMIRX_TMR_STA_CNT_EVT_MASK)) {
+
+        // Clear counter event
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_TMR_STA_OFFSET), (XV_HDMIRX_TMR_STA_CNT_EVT_MASK));
+
+        // Idle state
+        if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_IDLE) {
+
+            // The link is stable now
+            // Then the aux and audio peripherals can be enabled
+            XV_HdmiRx_AuxEnable(InstancePtr);
+            XV_HdmiRx_AudioEnable(InstancePtr);
+
+			/* Release HDMI RX core resets */
+			XV_HdmiRx_INT_VRST(InstancePtr, FALSE);
+			XV_HdmiRx_INT_LRST(InstancePtr, FALSE);
+
+            // Enable link
+            XV_HdmiRx_LinkEnable(InstancePtr, (TRUE));
+
+            // Set stream status to init
+            InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_INIT;    // The stream init
+
+            // Clear GetVideoPropertiesTries
+            InstancePtr->Stream.GetVideoPropertiesTries = 0;
+
+            // Load timer - 200 ms (one UHD frame is 40 ms, 5 frames)
+            XV_HdmiRx_TmrStart(InstancePtr,
+			XV_HdmiRx_GetTime200Ms(InstancePtr));
+        }
+
+        // Init state
+        else if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_INIT) {
+
+            // Read video properties
+            if (XV_HdmiRx_GetVideoProperties(InstancePtr) == XST_SUCCESS) {
+
+            // Now we know the reference clock and color depth,
+            // the pixel clock can be calculated
+            // In case of YUV 422 the reference clock is the pixel clock
+            if (InstancePtr->Stream.Video.ColorFormatId == XVIDC_CSF_YCRCB_422) {
+                InstancePtr->Stream.PixelClk = InstancePtr->Stream.RefClk;
+            }
+
+            // For the other color spaces the pixel clock needs to be adjusted
+            else {
+
+                switch (InstancePtr->Stream.Video.ColorDepth) {
+                    case XVIDC_BPC_10:
+                        InstancePtr->Stream.PixelClk = (InstancePtr->Stream.RefClk * 4)/5;
+                        break;
+
+                    case XVIDC_BPC_12:
+                        InstancePtr->Stream.PixelClk = (InstancePtr->Stream.RefClk * 2)/3;
+                        break;
+
+                    case XVIDC_BPC_16:
+                        InstancePtr->Stream.PixelClk = InstancePtr->Stream.RefClk / 2;
+                        break;
+
+                    default:
+                        InstancePtr->Stream.PixelClk = InstancePtr->Stream.RefClk;
+                        break;
+                }
+            }
+
+				// Call stream init callback
+				if (InstancePtr->IsStreamInitCallbackSet) {
+					InstancePtr->StreamInitCallback(InstancePtr->StreamInitRef);
+				}
+			}
+
+            else {
+		// Load timer - 200 ms (one UHD frame is 40 ms, 5 frames)
+                XV_HdmiRx_TmrStart(InstancePtr,
+				XV_HdmiRx_GetTime200Ms(InstancePtr));
+            }
+        }
+
+        // Armed state
+        else if (InstancePtr->Stream.State == XV_HDMIRX_STATE_STREAM_ARM) {
+
+            /* Enable VTD */
+            XV_HdmiRx_VtdEnable(InstancePtr);
+
+            /* Enable interrupt */
+            XV_HdmiRx_VtdIntrEnable(InstancePtr);
+
+            // Set stream status to lock
+            InstancePtr->Stream.State = XV_HDMIRX_STATE_STREAM_LOCK;
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX AUX peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_AuxIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    u32 Status;
+    u8 Index;
+
+    /* Read Status register */
+    Status = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET));
+
+    /* Check for GCP colordepth event */
+    if ((Status) & (XV_HDMIRX_AUX_STA_GCP_CD_EVT_MASK)) {
+    	/* Clear event flag */
+    	XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET), (XV_HDMIRX_AUX_STA_GCP_CD_EVT_MASK));
+
+    	if ((Status) & (XV_HDMIRX_AUX_STA_GCP_MASK)) {
+    		InstancePtr->Stream.Video.ColorDepth = XV_HdmiRx_GetGcpColorDepth(InstancePtr);
+    	}
+    }
+
+    /* Check for new packet */
+    if ((Status) & (XV_HDMIRX_AUX_STA_NEW_MASK)) {
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET), (XV_HDMIRX_AUX_STA_NEW_MASK));
+
+        /* Set HDMI flag */
+        InstancePtr->Stream.IsHdmi = (TRUE);
+
+        /* Read header word and update AUX header field */
+        InstancePtr->Aux.Header.Data = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_DAT_OFFSET));
+
+        for (Index = 0x0; Index < 8; Index++) {
+            /* Read data word and update AUX data field */
+            InstancePtr->Aux.Data.Data[Index] = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_DAT_OFFSET));
+        }
+
+        /* Callback */
+        if (InstancePtr->IsAuxCallbackSet) {
+            InstancePtr->AuxCallback(InstancePtr->AuxRef);
+        }
+    }
+
+    /* Link integrity check */
+    if ((Status) & (XV_HDMIRX_AUX_STA_ERR_MASK)) {
+		XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET), (XV_HDMIRX_AUX_STA_ERR_MASK));
+
+        /* Callback */
+        if (InstancePtr->IsLinkErrorCallbackSet) {
+			InstancePtr->LinkErrorCallback(InstancePtr->LinkErrorRef);
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX AUD peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_AudIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    u32 Status;
+
+    // Read Status register
+    Status = XV_HdmiRx_ReadReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUD_STA_OFFSET));
+
+    // Check for active stream event
+    if ((Status) & (XV_HDMIRX_AUD_STA_ACT_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUD_STA_OFFSET), (XV_HDMIRX_AUD_STA_ACT_EVT_MASK));
+
+        InstancePtr->Stream.Audio.Active = (TRUE);
+    }
+
+    // Check for audio channel event
+    if ((Status) & (XV_HDMIRX_AUD_STA_CH_EVT_MASK)) {
+
+        // Clear event flag
+        XV_HdmiRx_WriteReg(InstancePtr->Config.BaseAddress, (XV_HDMIRX_AUD_STA_OFFSET), (XV_HDMIRX_AUD_STA_CH_EVT_MASK));
+
+        // Active channels
+	switch ((Status >> XV_HDMIRX_AUD_STA_AUD_CH_SHIFT) &
+			XV_HDMIRX_AUD_STA_AUD_CH_MASK) {
+            // 32 channels
+	case 6 :
+		InstancePtr->Stream.Audio.Channels = 32;
+		break;
+
+	// 24 channels
+	case 5 :
+		InstancePtr->Stream.Audio.Channels = 24;
+		break;
+
+	// 12 channels
+	case 4 :
+		InstancePtr->Stream.Audio.Channels = 12;
+		break;
+
+	// 8 channels
+	case 3 :
+		InstancePtr->Stream.Audio.Channels = 8;
+		break;
+
+	// 6 channels
+	case 2 :
+		InstancePtr->Stream.Audio.Channels = 6;
+		break;
+
+	// 4 channels
+	case 1 :
+		InstancePtr->Stream.Audio.Channels = 4;
+		break;
+
+	// 2 channels
+	default :
+		InstancePtr->Stream.Audio.Channels = 2;
+		break;
+	}
+
+        // Audio Format
+        InstancePtr->AudFormat = (XV_HdmiRx_AudioFormatType)((Status >> XV_HDMIRX_AUD_STA_AUD_FMT_SHIFT) & XV_HDMIRX_AUD_STA_AUD_FMT_MASK);
+
+        /* Callback */
+        if (InstancePtr->IsAudCallbackSet) {
+            InstancePtr->AudCallback(InstancePtr->AudRef);
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI RX Link Status
+* (LNKSTA) peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiRx_LinkStatusIntrHandler(XV_HdmiRx *InstancePtr)
+{
+    /* Callback */
+    if (InstancePtr->IsLnkStaCallbackSet) {
+        InstancePtr->LnkStaCallback(InstancePtr->LnkStaRef);
+    }
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirx_sinit.c
@@ -0,0 +1,93 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirx_sinit.c
+*
+* This file contains static initialization method for Xilinx HDMI RX core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.0   gm, mg 10/07/15 Initial release.
+
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmirx.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XV_HdmiRx_Config structure based
+* on the core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xv_hdmirx_g.c file.
+*
+* @param    DeviceId is the unique core ID of the HDMI RX core for the
+*       lookup operation.
+*
+* @return   XV_HdmiRx_LookupConfig returns a reference to a config record
+*       in the configuration table (in xv_hdmirx_g.c) corresponding
+*       to <i>DeviceId</i>, or NULL if no match is found.
+*
+* @note     None.
+*
+******************************************************************************/
+XV_HdmiRx_Config *XV_HdmiRx_LookupConfig(u16 DeviceId)
+{
+    extern XV_HdmiRx_Config
+            XV_HdmiRx_ConfigTable[XPAR_XV_HDMIRX_NUM_INSTANCES];
+    XV_HdmiRx_Config *CfgPtr = NULL;
+    u32 Index;
+
+    /* Checking for device id for which instance it is matching */
+    for (Index = (u32)0x0; Index < (u32)(XPAR_XV_HDMIRX_NUM_INSTANCES);
+                                Index++) {
+
+        /* Assigning address of config table if both device ids
+         * are matched
+         */
+        if (XV_HdmiRx_ConfigTable[Index].DeviceId == DeviceId) {
+            CfgPtr = &XV_HdmiRx_ConfigTable[Index];
+            break;
+        }
+    }
+
+    return (XV_HdmiRx_Config *)CfgPtr;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss.c
@@ -0,0 +1,2460 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirxss.c
+*
+* This is main code of Xilinx HDMI Receiver Subsystem device driver.
+* Please see xv_hdmirxss.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     15/01/16 Added 3D Video support
+* 1.2   yh     20/01/16 Added remapper support
+* 1.3   yh     01/02/16 Added set_ppc api
+* 1.4   yh     01/02/16 Removed xil_print "Cable (dis)connected"
+* 1.5   yh     01/02/16 Removed xil_printf("Active audio channels...)
+* 1.6   yh     15/02/16 Added default value to XV_HdmiRxSs_ConfigRemapper
+* 1.7   MG     03/02/16 Added HDCP support
+* 1.8   MG     10/02/16 Moved HDCP 2.2 reset from stream up/down callback
+*                       to connect callback
+* 1.9   MH     15/03/16 Added HDCP authenticated callback support
+* 1.10  MH     23/04/16 1. HDCP 1.x driver now uses AXI timer 4.1, so updated
+*                       to use AXI Timer config structure to determine timer
+*                       clock frequency
+*                       2. HDCP 1.x driver has fixed the problem where the
+*                       reset for the receiver causes the entire DDC peripheral
+*                       to get reset. Based on this change the driver has been
+*                       updated to use XV_HdmiRxSs_HdcpReset and
+*                       XV_HdmiRxSs_HdcpReset functions directly.
+*                       3. Updated XV_HdmiRxSs_HdcpEnable and
+*                       XV_HdmiRxSs_HdcpEnable functions to ensure that
+*                       HDCP 1.4 and 2.2 are mutually exclusive.
+*                       This fixes the problem where HDCP 1.4 and 2.2
+*                       state machines are running simultaneously.
+* 1.11  MG     13/05/16 Added DDC peripheral HDCP mode selection to XV_HdmiRxSs_HdcpEnable
+* 1.12  MH     23/06/16 Added HDCP repeater support.
+* 1.13  YH     18/07/16 1. Replace xil_print with xdbg_printf.
+*                       2. Replace MB_Sleep() with usleep_range(,  + /10)
+* 1.14  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XV_HdmiRxSs_CfgInitialize
+* 1.15  MH     26/07/16 Updates for automatic protocol switching
+* 1.16  MH     05/08/16 Updates to optimize out HDCP when excluded
+* 1.17  YH     17/08/16 Remove sleep in XV_HdmiRxSs_ResetRemapper
+*                       squash unused variable compiler warning
+*                       Added Event Log
+* 1.18  MH     08/10/16 Improve HDCP 1.4 authentication
+* 1.19  MG     31/10/16 Fixed issue with reference clock compensation in
+*                           XV_HdmiRxSS_SetStream
+* 1.20  YH     14/11/16 Added API to enable/disable YUV420/Pixel Drop Mode
+*                       for video bridge
+* 1.21  YH     14/11/16 Remove Remapper APIs
+*                       Replace XV_HdmiRxSs_ConfigRemapper API with
+*                       XV_HdmiRxSs_ConfigBridgeMode API as remapper feature is
+*                           moved to video bridge and controlled by HDMI core
+* 1.22  MMO    03/01/17 Add compiler option(XV_HDMIRXSS_LOG_ENABLE) to enable
+*                           Log
+*                       Move global variable XV_HdmiRx_VSIF VSIF to local
+*                           XV_HdmiRxSs_RetrieveVSInfoframe API
+*                       Move HDCP related API's to hdmirxss_hdcp.c
+* 1.23  MMO    10/02/17 Added Sync Loss and HDMI/DVI Interrupt Support
+*
+* 1.4   YH     07/07/17 Add new log type XV_HDMIRXSS_LOG_EVT_SETSTREAM_ERR
+*                       Report HDMI/DVI mode in HDMI example design info log
+*
+* 1.41  MMO    21/07/17 CR-979900 (Fix)
+*                       Removed the HDCP Push Event API Call when the
+*                       Aux Callback event happen
+*       MH     09/08/17 Added function XV_HdmiRxSs_HdcpSetCapability
+* 1.42  YH     06/10/17 Added function XV_HdmiRxSs_GetAudioFormat
+*       EB     10/10/17 Updated function XV_HdmiRxSs_ReportAudio to report
+*                           audio format
+* 5.00  YH     16/11/17 Added dedicated reset for each clock domain
+*              16/11/17 Added bridge overflow interrupt
+*       EB     16/01/18 Added parsing of InfoFrames during AuxCallback
+*                       Changed XV_HdmiRxSs_RetrieveVSInfoframe's input
+*                           parameter type
+*                       Added function XV_HdmiRxSs_GetAviInfoframe,
+*                           XV_HdmiRxSs_GetGCP, XV_HdmiRxSs_GetAudioInfoframe,
+*                           XV_HdmiRxSs_GetVSIF
+*                       Updated XV_HdmiRxSs_ConfigBridgeMode so Pixel
+*                           Pepetition is based on received AVI InfoFrame
+* 5.10  MMO    06/04/18 Updated XV_HdmiRxSs_ToggleHpd and XV_HdmiRxSs_Stop
+*                           for cleaner HPD flow during transition from HDMI2.0
+*                           to HDMI1.4
+*       YH     13/04/18 Fixed a bug in XV_HdmiRxSs_BrdgOverflowCallback
+* 5.20	EB     03/08/18 Added function XV_HdmiRxSs_AudioMute
+*                       Added TMDS Clock Ratio callback support
+* 5.40  EB     06/08/19 Added Vic and Video Timing mismatch callback support
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include <linux/delay.h>
+#include "xv_hdmirxss.h"
+#include "xv_hdmirxss_coreinit.h"
+
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+/**
+ * This typedef declares the driver instances of all the cores in the subsystem
+ */
+typedef struct
+{
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  XTmrCtr HdcpTimer;
+  XHdcp1x Hdcp14;
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  XHdcp22_Rx Hdcp22;
+#endif
+  XV_HdmiRx HdmiRx;
+} XV_HdmiRxSs_SubCores;
+
+/**************************** Local Global ***********************************/
+/** Define Driver instance of all sub-core included in the design */
+XV_HdmiRxSs_SubCores XV_HdmiRxSs_SubCoreRepo[XPAR_XV_HDMIRXSS_NUM_INSTANCES];
+
+/************************** Function Prototypes ******************************/
+static void XV_HdmiRxSs_GetIncludedSubcores(XV_HdmiRxSs *HdmiRxSsPtr,
+    u16 DevId);
+static void XV_HdmiRxSs_WaitUs(XV_HdmiRxSs *InstancePtr, u32 MicroSeconds);
+static void XV_HdmiRxSs_RetrieveVSInfoframe(XV_HdmiRxSs *HdmiRxSs);
+static int XV_HdmiRxSs_RegisterSubsysCallbacks(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ConnectCallback(void *CallbackRef);
+static void XV_HdmiRxSs_BrdgOverflowCallback(void *CallbackRef);
+static void XV_HdmiRxSs_AuxCallback(void *CallbackRef);
+static void XV_HdmiRxSs_AudCallback(void *CallbackRef);
+static void XV_HdmiRxSs_LnkStaCallback(void *CallbackRef);
+static void XV_HdmiRxSs_DdcCallback(void *CallbackRef);
+static void XV_HdmiRxSs_StreamDownCallback(void *CallbackRef);
+static void XV_HdmiRxSs_StreamInitCallback(void *CallbackRef);
+static void XV_HdmiRxSs_StreamUpCallback(void *CallbackRef);
+static void XV_HdmiRxSs_SyncLossCallback(void *CallbackRef);
+static void XV_HdmiRxSs_ModeCallback(void *CallbackRef);
+static void XV_HdmiRxSs_TmdsClkRatioCallback(void *CallbackRef);
+static void XV_HdmiRxSs_VicErrorCallback(void *CallbackRef);
+
+static void XV_HdmiRxSs_ReportCoreInfo(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ReportTiming(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ReportLinkQuality(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ReportDRMInfo(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ReportAudio(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ReportInfoFrame(XV_HdmiRxSs *InstancePtr);
+static void XV_HdmiRxSs_ReportSubcoreVersion(XV_HdmiRxSs *InstancePtr);
+
+static void XV_HdmiRxSs_ConfigBridgeMode(XV_HdmiRxSs *InstancePtr);
+
+/************************** Function Definition ******************************/
+
+void XV_HdmiRxSs_ReportInfo(XV_HdmiRxSs *InstancePtr)
+{
+    xil_printf("------------\r\n");
+    xil_printf("HDMI RX SubSystem\r\n");
+    xil_printf("------------\r\n");
+    XV_HdmiRxSs_ReportCoreInfo(InstancePtr);
+    XV_HdmiRxSs_ReportSubcoreVersion(InstancePtr);
+    xil_printf("\r\n");
+    xil_printf("HDMI RX Mode - ");
+    if (InstancePtr->HdmiRxPtr->Stream.IsHdmi == (TRUE)) {
+        xil_printf("HDMI\r\n");
+    }
+    else {
+        xil_printf("DVI\r\n");
+    }
+    xil_printf("------------\r\n");
+    xil_printf("HDMI RX timing\r\n");
+    xil_printf("------------\r\n");
+    XV_HdmiRxSs_ReportTiming(InstancePtr);
+    xil_printf("Link quality\r\n");
+    xil_printf("---------\r\n");
+    XV_HdmiRxSs_ReportLinkQuality(InstancePtr);
+    xil_printf("Audio\r\n");
+    xil_printf("---------\r\n");
+    XV_HdmiRxSs_ReportAudio(InstancePtr);
+    xil_printf("DRM info frame\r\n");
+    xil_printf("--------------\r\n");
+    XV_HdmiRxSs_ReportDRMInfo(InstancePtr);
+    xil_printf("Infoframe\r\n");
+    xil_printf("---------\r\n");
+    XV_HdmiRxSs_ReportInfoFrame(InstancePtr);
+    xil_printf("\r\n");
+}
+
+/*****************************************************************************/
+/**
+* This function reports list of cores included in Video Processing Subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance.
+*
+* @return None
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ReportCoreInfo(XV_HdmiRxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  xil_printf("\r\n  ->HDMI RX Subsystem Cores\r\n");
+
+  /* Report all the included cores in the subsystem instance */
+  if(InstancePtr->HdmiRxPtr)
+  {
+    xil_printf("    : HDMI RX \r\n");
+  }
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if(InstancePtr->Hdcp14Ptr)
+  {
+    xil_printf("    : HDCP 1.4 RX \r\n");
+  }
+
+  if(InstancePtr->HdcpTimerPtr)
+  {
+    xil_printf("    : HDCP: AXIS Timer\r\n");
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  if(InstancePtr->Hdcp22Ptr)
+  {
+    xil_printf("    : HDCP 2.2 RX \r\n");
+  }
+#endif
+}
+
+/******************************************************************************/
+/**
+ * This function installs a custom delay/sleep function to be used by the
+ *  XV_HdmiRxSs driver.
+ *
+ * @param   InstancePtr is a pointer to the HdmiSsRx instance.
+ * @param   CallbackFunc is the address to the callback function.
+ * @param   CallbackRef is the user data item (microseconds to delay) that
+ *      will be passed to the custom sleep/delay function when it is
+ *      invoked.
+ *
+ * @return  None.
+ *
+ * @note    None.
+ *
+*******************************************************************************/
+void XV_HdmiRxSs_SetUserTimerHandler(XV_HdmiRxSs *InstancePtr,
+            XVidC_DelayHandler CallbackFunc, void *CallbackRef)
+{
+    /* Verify arguments. */
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(CallbackFunc != NULL);
+    Xil_AssertVoid(CallbackRef != NULL);
+
+    InstancePtr->UserTimerWaitUs = CallbackFunc;
+    InstancePtr->UserTimerPtr = CallbackRef;
+}
+
+/******************************************************************************/
+/**
+ * This function is the delay/sleep function for the XV_HdmiRxSs driver. For the
+ * Zynq family, there exists native sleep functionality. For MicroBlaze however,
+ * there does not exist such functionality. In the MicroBlaze case, the default
+ * method for delaying is to use a predetermined amount of loop iterations. This
+ * method is prone to inaccuracy and dependent on system configuration; for
+ * greater accuracy, the user may supply their own delay/sleep handler, pointed
+ * to by InstancePtr->UserTimerWaitUs, which may have better accuracy if a
+ * hardware timer is used.
+ *
+ * @param   InstancePtr is a pointer to the HdmiSsRx instance.
+ * @param   MicroSeconds is the number of microseconds to delay/sleep for.
+ *
+ * @return  None.
+ *
+ * @note    None.
+ *
+*******************************************************************************/
+static void XV_HdmiRxSs_WaitUs(XV_HdmiRxSs *InstancePtr, u32 MicroSeconds)
+{
+    /* Verify arguments. */
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    if (MicroSeconds == 0) {
+        return;
+    }
+
+    if (InstancePtr->UserTimerWaitUs != NULL) {
+        /* Use the timer handler specified by the user for better
+         * accuracy. */
+        InstancePtr->UserTimerWaitUs(InstancePtr, MicroSeconds);
+    }
+    else {
+        usleep_range(MicroSeconds, MicroSeconds + MicroSeconds/10);
+    }
+}
+
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDMI RX
+ *
+ * @param  InstancePtr is a pointer to the HDMI RX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiRxSS_HdmiRxIntrHandler(XV_HdmiRxSs *InstancePtr)
+{
+    XV_HdmiRx_IntrHandler(InstancePtr->HdmiRxPtr);
+}
+
+/*****************************************************************************/
+/**
+ * This function register's all sub-core ISR's with interrupt controller and
+ * any subsystem level call back function with requisite sub-core
+ *
+ * @param  InstancePtr is a pointer to the Subsystem instance to be
+ *       worked on.
+ *
+ *****************************************************************************/
+static int XV_HdmiRxSs_RegisterSubsysCallbacks(XV_HdmiRxSs *InstancePtr)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = InstancePtr;
+
+  //Register HDMI callbacks
+  if(HdmiRxSsPtr->HdmiRxPtr) {
+    /*
+     * Register call back for Rx Core Interrupts.
+     */
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_CONNECT,
+                          (void *)XV_HdmiRxSs_ConnectCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_BRDG_OVERFLOW,
+                          (void *)XV_HdmiRxSs_BrdgOverflowCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_AUX,
+                          (void *)XV_HdmiRxSs_AuxCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_AUD,
+                          (void *)XV_HdmiRxSs_AudCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_LNKSTA,
+                          (void *)XV_HdmiRxSs_LnkStaCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_DDC,
+                          (void *)XV_HdmiRxSs_DdcCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_STREAM_DOWN,
+                          (void *)XV_HdmiRxSs_StreamDownCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_STREAM_INIT,
+                          (void *)XV_HdmiRxSs_StreamInitCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_STREAM_UP,
+                          (void *)XV_HdmiRxSs_StreamUpCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_SYNC_LOSS,
+                          (void *)XV_HdmiRxSs_SyncLossCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_MODE,
+                          (void *)XV_HdmiRxSs_ModeCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_TMDS_CLK_RATIO,
+                          (void *)XV_HdmiRxSs_TmdsClkRatioCallback,
+                          (void *)InstancePtr);
+
+    XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                          XV_HDMIRX_HANDLER_VIC_ERROR,
+                          (void *)XV_HdmiRxSs_VicErrorCallback,
+                          (void *)InstancePtr);
+  }
+
+  return(XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function queries the subsystem instance configuration to determine
+* the included sub-cores. For each sub-core that is present in the design
+* the sub-core driver instance is binded with the subsystem sub-core driver
+* handle
+*
+* @param  HdmiRxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+static void XV_HdmiRxSs_GetIncludedSubcores(XV_HdmiRxSs *HdmiRxSsPtr, u16 DevId)
+{
+  HdmiRxSsPtr->HdmiRxPtr   =((HdmiRxSsPtr->Config.HdmiRx.IsPresent) ?
+                            (&XV_HdmiRxSs_SubCoreRepo[DevId].HdmiRx) : NULL);
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  HdmiRxSsPtr->Hdcp14Ptr   =((HdmiRxSsPtr->Config.Hdcp14.IsPresent) ?
+                            (&XV_HdmiRxSs_SubCoreRepo[DevId].Hdcp14) : NULL);
+  HdmiRxSsPtr->HdcpTimerPtr=((HdmiRxSsPtr->Config.HdcpTimer.IsPresent) ?
+                            (&XV_HdmiRxSs_SubCoreRepo[DevId].HdcpTimer) : NULL);
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  HdmiRxSsPtr->Hdcp22Ptr   =((HdmiRxSsPtr->Config.Hdcp22.IsPresent) ?
+                            (&XV_HdmiRxSs_SubCoreRepo[DevId].Hdcp22) : NULL);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the video subsystem and included sub-cores.
+* This function must be called prior to using the subsystem. Initialization
+* includes setting up the instance data for top level as well as all included
+* sub-core therein, and ensuring the hardware is in a known stable state.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+* @param  CfgPtr points to the configuration structure associated with the
+*         subsystem instance.
+* @param  EffectiveAddr is the base address of the device. If address
+*         translation is being used, then this parameter must reflect the
+*         virtual base address. Otherwise, the physical address should be
+*         used.
+*
+* @return XST_SUCCESS if initialization is successful else XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiRxSs_CfgInitialize(XV_HdmiRxSs *InstancePtr,
+    XV_HdmiRxSs_Config *CfgPtr,
+    UINTPTR EffectiveAddr)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = InstancePtr;
+  struct v4l2_hdr10_payload *DrmInfoFramePtr;
+
+  /* Verify arguments */
+  Xil_AssertNonvoid(HdmiRxSsPtr != NULL);
+  Xil_AssertNonvoid(CfgPtr != NULL);
+  Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+  /* Setup the instance */
+  memcpy((void *)&(HdmiRxSsPtr->Config), (const void *)CfgPtr,
+    sizeof(XV_HdmiRxSs_Config));
+  HdmiRxSsPtr->Config.BaseAddress = EffectiveAddr;
+
+  /* Determine sub-cores included in the provided instance of subsystem */
+  XV_HdmiRxSs_GetIncludedSubcores(HdmiRxSsPtr, CfgPtr->DeviceId);
+
+  /* Initialize all included sub_cores */
+  if(HdmiRxSsPtr->HdmiRxPtr)
+  {
+    if(XV_HdmiRxSs_SubcoreInitHdmiRx(HdmiRxSsPtr) != XST_SUCCESS)
+    {
+      return(XST_FAILURE);
+    }
+  }
+
+  /* Register Callbacks */
+  XV_HdmiRxSs_RegisterSubsysCallbacks(HdmiRxSsPtr);
+
+#ifdef USE_HDCP_RX
+  /* Default value */
+  HdmiRxSsPtr->HdcpIsReady = (FALSE);
+#endif
+
+  /* Reset the hardware and set the flag to indicate the
+     subsystem is ready
+   */
+  XV_HdmiRxSs_Reset(HdmiRxSsPtr);
+  HdmiRxSsPtr->IsReady = XIL_COMPONENT_IS_READY;
+
+  DrmInfoFramePtr = XV_HdmiRxSs_GetDrmInfoframe(HdmiRxSsPtr);
+
+  DrmInfoFramePtr->metadata_type = 0xFF;
+  DrmInfoFramePtr->eotf = 0xFF;
+
+  return(XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the hdcp subsystem and included sub-cores.
+* This function must be called prior to using the subsystem. Initialization
+* includes setting up the instance data for top level as well as all included
+* sub-core therein, and ensuring the hardware is in a known stable state.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+* @param  CfgPtr points to the configuration structure associated with the
+*         subsystem instance.
+* @param  EffectiveAddr is the base address of the device. If address
+*         translation is being used, then this parameter must reflect the
+*         virtual base address. Otherwise, the physical address should be
+*         used.
+*
+* @return XST_SUCCESS if initialization is successful else XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiRxSs_CfgInitializeHdcp(XV_HdmiRxSs *InstancePtr,
+    XV_HdmiRxSs_Config *CfgPtr,
+    UINTPTR EffectiveAddr)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = InstancePtr;
+
+  /* Verify arguments */
+  Xil_AssertNonvoid(HdmiRxSsPtr != NULL);
+  Xil_AssertNonvoid(CfgPtr != NULL);
+  Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  if(HdmiRxSsPtr->Hdcp14Ptr) {
+    if(XV_HdmiRxSs_SubcoreInitHdcp14(HdmiRxSsPtr) != XST_SUCCESS) {
+      return(XST_FAILURE);
+    }
+  }
+
+  if(HdmiRxSsPtr->HdcpTimerPtr) {
+    if(XV_HdmiRxSs_SubcoreInitHdcpTimer(HdmiRxSsPtr) != XST_SUCCESS) {
+      return(XST_FAILURE);
+    }
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  // HDCP 2.2
+  if(HdmiRxSsPtr->Hdcp22Ptr) {
+    if(XV_HdmiRxSs_SubcoreInitHdcp22(HdmiRxSsPtr) != XST_SUCCESS) {
+      return(XST_FAILURE);
+    }
+  }
+#endif
+
+#ifdef USE_HDCP_RX
+  /* Default value */
+  HdmiRxSsPtr->HdcpIsReady = (FALSE);
+  XV_HdmiRxSs_HdcpSetCapability(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_BOTH);
+  HdmiRxSsPtr->UserHdcpProt = XV_HDMIRXSS_HDCP_NOUSERPREF;
+#endif
+
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+  /* HDCP is ready when both HDCP cores are instantiated and all keys are
+     loaded */
+  if (HdmiRxSsPtr->Hdcp14Ptr && HdmiRxSsPtr->Hdcp22Ptr &&
+      HdmiRxSsPtr->Hdcp22Lc128Ptr && HdmiRxSsPtr->Hdcp14KeyPtr &&
+      HdmiRxSsPtr->Hdcp22PrivateKeyPtr) {
+    HdmiRxSsPtr->HdcpIsReady = (TRUE);
+
+    /* Set default HDCP content protection scheme */
+    XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_14);
+  }
+#endif
+
+#if defined(XPAR_XHDCP_NUM_INSTANCES)
+  /* HDCP is ready when only the HDCP 1.4 core is instantiated and the key is
+     loaded */
+  if (!HdmiRxSsPtr->HdcpIsReady && HdmiRxSsPtr->Hdcp14Ptr &&
+       HdmiRxSsPtr->Hdcp14KeyPtr) {
+    HdmiRxSsPtr->HdcpIsReady = (TRUE);
+
+    /* Set default HDCP content protection scheme */
+    XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_14);
+  }
+#endif
+
+#if defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+  /* HDCP is ready when only the HDCP 2.2 core is instantiated and the keys are
+     loaded */
+  if (!HdmiRxSsPtr->HdcpIsReady && HdmiRxSsPtr->Hdcp22Ptr &&
+       HdmiRxSsPtr->Hdcp22Lc128Ptr && HdmiRxSsPtr->Hdcp22PrivateKeyPtr) {
+    HdmiRxSsPtr->HdcpIsReady = (TRUE);
+
+    /* Set default HDCP content protection scheme */
+    XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_22);
+  }
+#endif
+
+  XV_HdmiRxSs_Reset(HdmiRxSsPtr);
+
+  return(XST_SUCCESS);
+}
+
+/****************************************************************************/
+/**
+* This function starts the HDMI RX subsystem including all sub-cores that are
+* included in the processing pipeline for a given use-case. Video pipe is
+* started from back to front
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+* @note Cores are started only if the corresponding start flag in the scratch
+*       pad memory is set. This allows to selectively start only those cores
+*       included in the processing chain
+******************************************************************************/
+void XV_HdmiRxSs_Start(XV_HdmiRxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_START, 0);
+#endif
+  /* Drive HDMI RX HPD High */
+  XV_HdmiRx_SetHpd(InstancePtr->HdmiRxPtr, TRUE);
+}
+
+/*****************************************************************************/
+/**
+* This function stops the HDMI RX subsystem including all sub-cores
+* Stop the video pipe starting from front to back
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiRxSs_Stop(XV_HdmiRxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  /* Clear SCDC variables */
+  XV_HdmiRx_DdcScdcClear(InstancePtr->HdmiRxPtr);
+
+  /* Disable the scrambler */
+  XV_HdmiRx_SetScrambler(InstancePtr->HdmiRxPtr, (FALSE));
+
+  /* Drive HDMI RX HPD Low */
+  XV_HdmiRx_SetHpd(InstancePtr->HdmiRxPtr, (FALSE));
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_STOP, 0);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function resets the video subsystem sub-cores. There are 2 reset
+* networks within the subsystem
+*  - For cores that are on AXIS interface
+*  - For cores that are on AXI-MM interface
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiRxSs_Reset(XV_HdmiRxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_RESET, 0);
+#endif
+
+  /* Assert HDMI RX core resets */
+  XV_HdmiRxSs_RXCore_VRST(InstancePtr, TRUE);
+  XV_HdmiRxSs_RXCore_LRST(InstancePtr, TRUE);
+
+  /* Assert SYSCLK VID_IN bridge reset */
+  XV_HdmiRxSs_SYSRST(InstancePtr, TRUE);
+
+  /* Release HDMI RX core resets */
+  XV_HdmiRxSs_RXCore_VRST(InstancePtr, FALSE);
+  XV_HdmiRxSs_RXCore_LRST(InstancePtr, FALSE);
+
+  /* Release SYSCLK VID_IN bridge reset */
+  XV_HdmiRxSs_SYSRST(InstancePtr, FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the Internal Video reset
+* of the HDMI subcore within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiRxSs_RXCore_VRST(XV_HdmiRxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiRx_INT_VRST(InstancePtr->HdmiRxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the Internal Link reset
+* of the HDMI subcore within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiRxSs_RXCore_LRST(XV_HdmiRxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiRx_INT_LRST(InstancePtr->HdmiRxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the video reset of other
+* blocks within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiRxSs_VRST(XV_HdmiRxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiRx_EXT_VRST(InstancePtr->HdmiRxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the system reset of other
+* blocks within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiRxSs_SYSRST(XV_HdmiRxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiRx_EXT_SYSRST(InstancePtr->HdmiRxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a Bridge overflow event has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_BrdgOverflowCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->BrdgOverflowCallback) {
+    HdmiRxSsPtr->BrdgOverflowCallback(HdmiRxSsPtr->BrdgOverflowRef);
+  }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a RX connect event has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ConnectCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  // Is the cable connected?
+  if (XV_HdmiRx_IsStreamConnected(HdmiRxSsPtr->HdmiRxPtr)) {
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_CONNECT, 0);
+#endif
+    // Set RX hot plug detect
+    XV_HdmiRx_SetHpd(HdmiRxSsPtr->HdmiRxPtr, TRUE);
+
+    // Set stream connected flag
+    HdmiRxSsPtr->IsStreamConnected = (TRUE);
+
+#ifdef USE_HDCP_RX
+    // Push connect event to HDCP event queue
+    XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_CONNECT_EVT);
+#endif
+  }
+
+  // RX cable is disconnected
+  else {
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_DISCONNECT, 0);
+#endif
+    // Clear RX hot plug detect
+    XV_HdmiRx_SetHpd(HdmiRxSsPtr->HdmiRxPtr, FALSE);
+
+    // Set stream connected flag
+    HdmiRxSsPtr->IsStreamConnected = (FALSE);
+
+#ifdef USE_HDCP_RX
+    // Push disconnect event to HDCP event queue
+    XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_DISCONNECT_EVT);
+#endif
+
+    XV_HdmiRx_SetScrambler(HdmiRxSsPtr->HdmiRxPtr, (FALSE)); //Disable scrambler
+  }
+
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->ConnectCallback) {
+    HdmiRxSsPtr->ConnectCallback(HdmiRxSsPtr->ConnectRef);
+  }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a RX AUX IRQ has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_AuxCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+  XHdmiC_Aux *AuxPtr;
+  XHdmiC_AVI_InfoFrame *AviInfoFramePtr;
+  XHdmiC_AVI_InfoFrame *AviInfoFramePrevPtr;
+  XHdmiC_GeneralControlPacket *GeneralControlPacketPtr;
+  XHdmiC_AudioInfoFrame *AudioInfoFramePtr;
+  struct v4l2_hdr10_payload *DrmInfoFramePtr;
+
+  AviInfoFramePtr = XV_HdmiRxSs_GetAviInfoframe(HdmiRxSsPtr);
+  AviInfoFramePrevPtr = XV_HdmiRxSs_GetAviInfoframePrev(HdmiRxSsPtr);
+  GeneralControlPacketPtr = XV_HdmiRxSs_GetGCP(HdmiRxSsPtr);
+  AudioInfoFramePtr = XV_HdmiRxSs_GetAudioInfoframe(HdmiRxSsPtr);
+  DrmInfoFramePtr = XV_HdmiRxSs_GetDrmInfoframe(HdmiRxSsPtr);
+  AuxPtr = XV_HdmiRxSs_GetAuxiliary(HdmiRxSsPtr);
+
+  if(AuxPtr->Header.Byte[0] == AUX_VSIF_TYPE){
+	  // Retrieve Vendor Specific Info Frame
+	  XV_HdmiRxSs_RetrieveVSInfoframe(HdmiRxSsPtr);
+  } else if(AuxPtr->Header.Byte[0] == AUX_AVI_INFOFRAME_TYPE){
+
+	  // Reset Avi InfoFrame
+	  (void)memset((void *)AviInfoFramePtr, 0, sizeof(XHdmiC_AVI_InfoFrame));
+	  // Parse Aux to retrieve Avi InfoFrame
+	  XV_HdmiC_ParseAVIInfoFrame(AuxPtr, AviInfoFramePtr);
+	  if (memcmp(AviInfoFramePrevPtr, AviInfoFramePtr,
+				  sizeof(XHdmiC_AVI_InfoFrame))) {
+		memcpy(AviInfoFramePrevPtr, AviInfoFramePtr,
+				  sizeof(XHdmiC_AVI_InfoFrame));
+		HdmiRxSsPtr->AVIInfoChanged = true;
+	  }
+
+	  HdmiRxSsPtr->HdmiRxPtr->Stream.Video.ColorFormatId =
+	  			XV_HdmiRx_GetAviColorSpace(HdmiRxSsPtr->HdmiRxPtr);
+	  HdmiRxSsPtr->HdmiRxPtr->Stream.Vic =
+				XV_HdmiRx_GetAviVic(HdmiRxSsPtr->HdmiRxPtr);
+	  HdmiRxSsPtr->HdmiRxPtr->Stream.Video.AspectRatio =
+				XV_HdmiC_IFAspectRatio_To_XVidC(HdmiRxSsPtr->AVIInfoframe.PicAspectRatio);
+  } else if(AuxPtr->Header.Byte[0] == AUX_GENERAL_CONTROL_PACKET_TYPE) {
+	  // Reset General Control Packet
+	  (void)memset((void *)GeneralControlPacketPtr, 0, sizeof(XHdmiC_GeneralControlPacket));
+	  // Parse Aux to retrieve General Control Packet
+	  XV_HdmiC_ParseGCP(AuxPtr, GeneralControlPacketPtr);
+	  // Stream.Video.ColorDepth is updated from the core during AUX INTR
+  } else if(AuxPtr->Header.Byte[0] == AUX_AUDIO_INFOFRAME_TYPE) {
+	  // Reset Audio InfoFrame
+	  (void)memset((void *)AudioInfoFramePtr, 0, sizeof(XHdmiC_AudioInfoFrame));
+	  // Parse Aux to retrieve Audio InfoFrame
+	  XV_HdmiC_ParseAudioInfoFrame(AuxPtr, AudioInfoFramePtr);
+  } else if(AuxPtr->Header.Byte[0] == AUX_DRM_INFOFRAME_TYPE) {
+	  // Reset HDR InfoFrame
+	  (void)memset((void *)DrmInfoFramePtr, 0, sizeof(struct v4l2_hdr10_payload));
+	  // Parse Aux to retrieve HDR InfoFrame
+	  XV_HdmiC_ParseDRMIF(AuxPtr, DrmInfoFramePtr);
+  }
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->AuxCallback) {
+      HdmiRxSsPtr->AuxCallback(HdmiRxSsPtr->AuxRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a RX Sync Loss IRQ has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_SyncLossCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  if (HdmiRxSsPtr->HdmiRxPtr->Stream.SyncStatus ==
+		  	  	  	  	  	  	  	  	  	  	XV_HDMIRX_SYNCSTAT_SYNC_LOSS) {
+  // Push sync loss event to HDCP event queue
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_SYNCLOSS, 0);
+#endif
+
+#ifdef USE_HDCP_RX
+  XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_SYNC_LOSS_EVT);
+#endif
+  }
+  // Sync is recovered/establish
+  else if (HdmiRxSsPtr->HdmiRxPtr->Stream.SyncStatus ==
+		  	  	  	  	  	  	  	  	  	  	 XV_HDMIRX_SYNCSTAT_SYNC_EST) {
+	  // Push sync loss event to HDCP event queue
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+	  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_SYNCEST, 0);
+#endif
+
+#ifdef USE_HDCP_RX
+	  XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_SYNC_EST_EVT);
+#endif
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the mode has transitioned from DVI to HDMI or
+* vice versa.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ModeCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  // HDMI mode
+  if (XV_HdmiRxSs_GetVideoStreamType(HdmiRxSsPtr )) {
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_HDMIMODE, 0);
+#endif
+#ifdef USE_HDCP_RX
+    XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_HDMI_MODE_EVT);
+#endif
+  }
+
+  // DVI mode
+  else {
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_DVIMODE, 0);
+#endif
+#ifdef USE_HDCP_RX
+    XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_DVI_MODE_EVT);
+#endif
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the TMDS CLK ratio changes.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_TmdsClkRatioCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->TmdsClkRatioCallback) {
+      HdmiRxSsPtr->TmdsClkRatioCallback(HdmiRxSsPtr->TmdsClkRatioRef);
+  }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the Vic does not match with the detected video
+* timing.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_VicErrorCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_VICERROR, 0);
+#endif
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->VicErrorCallback) {
+	HdmiRxSsPtr->VicErrorCallback(HdmiRxSsPtr->VicErrorRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function retrieves the Vendor Specific Info Frame.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_RetrieveVSInfoframe(XV_HdmiRxSs *HdmiRxSs)
+{
+  /** Vendor-Specific InfoFrame structure */
+  XHdmiC_VSIF *VSIFPtr;
+  VSIFPtr = XV_HdmiRxSs_GetVSIF(HdmiRxSs);
+
+  if (HdmiRxSs->HdmiRxPtr->Aux.Header.Byte[0] == AUX_VSIF_TYPE) {
+	  // Reset Vendor Specific InfoFrame
+	  (void)memset((void *)VSIFPtr, 0, sizeof(XHdmiC_VSIF));
+
+	  XV_HdmiC_VSIF_ParsePacket(&HdmiRxSs->HdmiRxPtr->Aux, VSIFPtr);
+
+      // Defaults
+      HdmiRxSs->HdmiRxPtr->Stream.Video.Is3D = FALSE;
+      HdmiRxSs->HdmiRxPtr->Stream.Video.Info_3D.Format = XVIDC_3D_UNKNOWN;
+
+      if (VSIFPtr->Format == XHDMIC_VSIF_VF_3D) {
+          HdmiRxSs->HdmiRxPtr->Stream.Video.Is3D = TRUE;
+          HdmiRxSs->HdmiRxPtr->Stream.Video.Info_3D = VSIFPtr->Info_3D.Stream;
+      } else if (VSIFPtr->Format == XHDMIC_VSIF_VF_EXTRES) {
+          switch(VSIFPtr->HDMI_VIC) {
+              case 1 :
+                  HdmiRxSs->HdmiRxPtr->Stream.Vic = 95;
+                  break;
+
+              case 2 :
+                  HdmiRxSs->HdmiRxPtr->Stream.Vic = 94;
+                  break;
+
+              case 3 :
+                  HdmiRxSs->HdmiRxPtr->Stream.Vic = 93;
+                  break;
+
+              case 4 :
+                  HdmiRxSs->HdmiRxPtr->Stream.Vic = 98;
+                  break;
+
+              default :
+                  break;
+          }
+      }
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a RX Audio IRQ has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_AudCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  u8 Channels;
+
+  if (XV_HdmiRx_IsAudioActive(HdmiRxSsPtr->HdmiRxPtr)) {
+
+    // Get audio channels
+    Channels = XV_HdmiRx_GetAudioChannels(HdmiRxSsPtr->HdmiRxPtr);
+    HdmiRxSsPtr->AudioChannels = Channels;
+  }
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->AudCallback) {
+      HdmiRxSsPtr->AudCallback(HdmiRxSsPtr->AudRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a RX Link Status IRQ has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_LnkStaCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  HdmiRxSsPtr->IsLinkStatusErrMax =
+    XV_HdmiRx_IsLinkStatusErrMax(HdmiRxSsPtr->HdmiRxPtr);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_LINKSTATUS, 0);
+#endif
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->LnkStaCallback) {
+      HdmiRxSsPtr->LnkStaCallback(HdmiRxSsPtr->LnkStaRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a RX DDC IRQ has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_DdcCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->DdcCallback) {
+      HdmiRxSsPtr->DdcCallback(HdmiRxSsPtr->DdcRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the RX stream is down.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_StreamDownCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+  struct v4l2_hdr10_payload *DrmInfoFramePtr;
+  XHdmiC_AVI_InfoFrame *AviInfoFramePtr;
+
+  /* Assert HDMI RX core resets */
+  XV_HdmiRxSs_RXCore_VRST(HdmiRxSsPtr, TRUE);
+  XV_HdmiRxSs_RXCore_LRST(HdmiRxSsPtr, TRUE);
+
+  /* Assert SYSCLK VID_IN bridge reset */
+  XV_HdmiRxSs_SYSRST(HdmiRxSsPtr, TRUE);
+
+  /* Set stream up flag */
+  HdmiRxSsPtr->IsStreamUp = (FALSE);
+  DrmInfoFramePtr = XV_HdmiRxSs_GetDrmInfoframe(HdmiRxSsPtr);
+
+  DrmInfoFramePtr->metadata_type = 0xFF;
+  DrmInfoFramePtr->eotf = 0xFF;
+  AviInfoFramePtr = XV_HdmiRxSs_GetAviInfoframe(HdmiRxSsPtr);
+  memset((void *)AviInfoFramePtr, 0, sizeof(XHdmiC_AVI_InfoFrame));
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_STREAMDOWN, 0);
+#endif
+#ifdef USE_HDCP_RX
+  // Push stream-down event to HDCP event queue
+  XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_STREAMDOWN_EVT);
+#endif
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->StreamDownCallback) {
+      HdmiRxSsPtr->StreamDownCallback(HdmiRxSsPtr->StreamDownRef);
+  }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the RX stream init .
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_StreamInitCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_STREAMINIT, 0);
+#endif
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->StreamInitCallback) {
+      HdmiRxSsPtr->StreamInitCallback(HdmiRxSsPtr->StreamInitRef);
+  }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the RX stream is up.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_StreamUpCallback(void *CallbackRef)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)CallbackRef;
+
+  /* Clear link Status error counters */
+  XV_HdmiRx_ClearLinkStatus(HdmiRxSsPtr->HdmiRxPtr);
+
+  /* Set stream up flag */
+  HdmiRxSsPtr->IsStreamUp = (TRUE);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_STREAMUP, 0);
+#endif
+#ifdef USE_HDCP_RX
+  // Push stream-up event to HDCP event queue
+  XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_STREAMUP_EVT);
+#endif
+
+  /* Configure Remapper according to HW setting and video format */
+  XV_HdmiRxSs_ConfigBridgeMode(HdmiRxSsPtr);
+
+  // Check if user callback has been registered
+  if (HdmiRxSsPtr->StreamUpCallback) {
+      HdmiRxSsPtr->StreamUpCallback(HdmiRxSsPtr->StreamUpRef);
+  }
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                     Callback Function Type
+* -----------------------         --------------------------------------------------
+* (XV_HDMIRXSS_HANDLER_CONNECT)             HpdCallback
+* (XV_HDMIRXSS_HANDLER_VS)                  VsCallback
+* (XV_HDMIRXSS_HANDLER_STREAM_DOWN)         StreamDownCallback
+* (XV_HDMIRXSS_HANDLER_STREAM_UP)           StreamUpCallback
+* (XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATED)
+* (XV_HDMIRXSS_HANDLER_HDCP_UNAUTHENTICATED)
+* (XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATION_REQUEST)
+* (XV_HDMIRXSS_HANDLER_HDCP_STREAM_MANAGE_REQUEST)
+* (XV_HDMIRXSS_HANDLER_HDCP_TOPOLOGY_UPDATE)
+* </pre>
+*
+* @param    InstancePtr is a pointer to the HDMI RX Subsystem instance.
+* @param    HandlerType specifies the type of handler.
+* @param    CallbackFunc is the address of the callback function.
+* @param    CallbackRef is a user data item that will be passed to the
+*       callback function when it is invoked.
+*
+* @return
+*       - XST_SUCCESS if callback function installed successfully.
+*       - XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note     Invoking this function for a handler that already has been
+*       installed replaces it with the new handler.
+*
+******************************************************************************/
+int XV_HdmiRxSs_SetCallback(XV_HdmiRxSs *InstancePtr,
+		XV_HdmiRxSs_HandlerType HandlerType,
+		void *CallbackFunc,
+		void *CallbackRef)
+{
+    u32 Status;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(HandlerType >= (XV_HDMIRXSS_HANDLER_CONNECT));
+    Xil_AssertNonvoid(CallbackFunc != NULL);
+    Xil_AssertNonvoid(CallbackRef != NULL);
+
+    /* Check for handler type */
+    switch (HandlerType) {
+
+        case (XV_HDMIRXSS_HANDLER_CONNECT):
+            InstancePtr->ConnectCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->ConnectRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRXSS_HANDLER_BRDGOVERFLOW):
+            InstancePtr->BrdgOverflowCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->BrdgOverflowRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRXSS_HANDLER_AUX):
+            InstancePtr->AuxCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->AuxRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRXSS_HANDLER_AUD):
+            InstancePtr->AudCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->AudRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMIRXSS_HANDLER_LNKSTA):
+            InstancePtr->LnkStaCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->LnkStaRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Ddc
+        case (XV_HDMIRXSS_HANDLER_DDC):
+            InstancePtr->DdcCallback =(XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->DdcRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream down
+        case (XV_HDMIRXSS_HANDLER_STREAM_DOWN):
+            InstancePtr->StreamDownCallback =(XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->StreamDownRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream Init
+        case (XV_HDMIRXSS_HANDLER_STREAM_INIT):
+            InstancePtr->StreamInitCallback =(XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->StreamInitRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream up
+        case (XV_HDMIRXSS_HANDLER_STREAM_UP):
+            InstancePtr->StreamUpCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->StreamUpRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // TMDS_CLK_RATIO
+        case (XV_HDMIRXSS_HANDLER_TMDS_CLK_RATIO):
+            InstancePtr->TmdsClkRatioCallback =
+                                  (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->TmdsClkRatioRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // VIC_ERROR
+        case (XV_HDMIRXSS_HANDLER_VIC_ERROR):
+            InstancePtr->VicErrorCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->VicErrorRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP
+        case (XV_HDMIRXSS_HANDLER_HDCP):
+            InstancePtr->HdcpCallback = (XV_HdmiRxSs_Callback)CallbackFunc;
+            InstancePtr->HdcpRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP authenticated
+        case (XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATED):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            // Register HDCP 1.4 callbacks
+            if (InstancePtr->Hdcp14Ptr) {
+              XHdcp1x_SetCallback(InstancePtr->Hdcp14Ptr,
+                                  XHDCP1X_HANDLER_AUTHENTICATED,
+                                  (void *)(XHdcp1x_Callback)CallbackFunc,
+                                  (void *)CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+            // Register HDCP 2.2 callbacks
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Rx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_RX_HANDLER_AUTHENTICATED,
+                                    (void *)(XHdcp22_Rx_RunHandler)CallbackFunc,
+                                    (void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP authenticated
+        case (XV_HDMIRXSS_HANDLER_HDCP_UNAUTHENTICATED):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            // Register HDCP 1.4 callbacks
+            if (InstancePtr->Hdcp14Ptr) {
+              XHdcp1x_SetCallback(InstancePtr->Hdcp14Ptr,
+                                XHDCP1X_HANDLER_UNAUTHENTICATED,
+                                (void *)(XHdcp1x_Callback)CallbackFunc,
+                                (void *)CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+            // Register HDCP 2.2 callbacks
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Rx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_RX_HANDLER_UNAUTHENTICATED,
+                                    (void *)(XHdcp22_Rx_RunHandler)CallbackFunc,
+                                    (void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP authentication request
+        case (XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATION_REQUEST):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            // Register HDCP 1.4 callbacks
+            if (InstancePtr->Hdcp14Ptr) {
+        //Register the hdcp trigger downstream authentication callback
+               XHdcp1x_SetCallBack(InstancePtr->Hdcp14Ptr,
+                                   (XHdcp1x_HandlerType) XHDCP1X_RPTR_HDLR_TRIG_DOWNSTREAM_AUTH,
+                                   (void *) (XHdcp1x_Callback)CallbackFunc,
+                                   (void *) CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+            // Register HDCP 2.2 callbacks
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Rx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_RX_HANDLER_AUTHENTICATION_REQUEST,
+                                    (void *)(XHdcp22_Rx_RunHandler)CallbackFunc,
+                                    (void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP stream management request
+        case (XV_HDMIRXSS_HANDLER_HDCP_STREAM_MANAGE_REQUEST):
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+            // Register HDCP 2.2 callbacks
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Rx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_RX_HANDLER_STREAM_MANAGE_REQUEST,
+                                    (void *)(XHdcp22_Rx_RunHandler)CallbackFunc,
+                                    (void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP topology update request
+        case (XV_HDMIRXSS_HANDLER_HDCP_TOPOLOGY_UPDATE):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            // Register HDCP 1.4 callbacks
+            if (InstancePtr->Hdcp14Ptr) {
+              XHdcp1x_SetCallback(InstancePtr->Hdcp14Ptr,
+                                  XHDCP1X_HANDLER_TOPOLOGY_UPDATE,
+                                  (void *)(XHdcp1x_Callback)CallbackFunc,
+                                  (void *)CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+            // Register HDCP 2.2 callbacks
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Rx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_RX_HANDLER_TOPOLOGY_UPDATE,
+                                    (void *)(XHdcp22_Rx_RunHandler)CallbackFunc,
+                                    (void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP encryption status update
+        case (XV_HDMIRXSS_HANDLER_HDCP_ENCRYPTION_UPDATE):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            // Register HDCP 1.4 callbacks
+            if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetCallback(InstancePtr->Hdcp14Ptr,
+                                 XHDCP1X_HANDLER_ENCRYPTION_UPDATE,
+                                 (void *)(XHdcp1x_Callback)CallbackFunc,
+                                 (void *)CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+            // Register HDCP 2.2 callbacks
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Rx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_RX_HANDLER_ENCRYPTION_UPDATE,
+                                    (void *)(XHdcp22_Rx_RunHandler)CallbackFunc,
+                                    (void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        default:
+            Status = (XST_INVALID_PARAM);
+            break;
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the EDID parameters in the HDMI RX SS struct
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_SetEdidParam(XV_HdmiRxSs *InstancePtr, u8 *EdidDataPtr,
+                                                                u16 Length)
+{
+    InstancePtr->EdidPtr = EdidDataPtr;
+    InstancePtr->EdidLength = Length;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function loads the default EDID to the HDMI RX
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_LoadDefaultEdid(XV_HdmiRxSs *InstancePtr)
+{
+    u32 Status;
+
+    // Load new EDID
+    Status = XV_HdmiRx_DdcLoadEdid(InstancePtr->HdmiRxPtr, InstancePtr->EdidPtr,
+            InstancePtr->EdidLength);
+    if (Status == XST_SUCCESS) {
+        xil_printf("\r\nSuccessfully loaded edid.\r\n");
+    }
+    else {
+        xil_printf("\r\nError loading edid.\r\n");
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function loads the default EDID to the HDMI RX
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_LoadEdid(XV_HdmiRxSs *InstancePtr, u8 *EdidDataPtr,
+                                                                u16 Length)
+{
+    u32 Status;
+
+    // Load new EDID
+    Status = XV_HdmiRx_DdcLoadEdid(InstancePtr->HdmiRxPtr, EdidDataPtr, Length);
+
+    if (Status == XST_SUCCESS) {
+        xil_printf("\r\nSuccessfully loaded edid.\r\n");
+    }
+    else {
+        xil_printf("\r\nError loading edid.\r\n");
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the HPD on the HDMI RX.
+*
+* @param  Value is a flag used to set the HPD.
+*   - TRUE drives HPD high
+*   - FALSE drives HPD low
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_SetHpd(XV_HdmiRxSs *InstancePtr, u8 Value)
+{
+  /* Drive HDMI RX HPD based on the input value */
+  XV_HdmiRx_SetHpd(InstancePtr->HdmiRxPtr, Value);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function toggles the HPD on the HDMI RX.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_ToggleHpd(XV_HdmiRxSs *InstancePtr)
+{
+  /* Clear SCDC variables */
+  XV_HdmiRx_DdcScdcClear(InstancePtr->HdmiRxPtr);
+
+  /* Disable the scrambler */
+  XV_HdmiRx_SetScrambler(InstancePtr->HdmiRxPtr, (FALSE));
+
+  /* Drive HDMI RX HPD Low */
+  XV_HdmiRx_SetHpd(InstancePtr->HdmiRxPtr, (FALSE));
+
+  /* Wait 500 ms */
+  XV_HdmiRxSs_WaitUs(InstancePtr, 500000);
+
+  /* Drive HDMI RX HPD High */
+  XV_HdmiRx_SetHpd(InstancePtr->HdmiRxPtr, (TRUE));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS Aux structure
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return XVidC_VideoStream pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_Aux *XV_HdmiRxSs_GetAuxiliary(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->HdmiRxPtr->Aux));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS AVI InfoFrame structure
+*
+* @param  InstancePtr pointer to XV_HdmiRXSs instance
+*
+* @return XHdmiC_AVI_InfoFrame pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_AVI_InfoFrame *XV_HdmiRxSs_GetAviInfoframe(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->AVIInfoframe));
+}
+
+XHdmiC_AVI_InfoFrame *XV_HdmiRxSs_GetAviInfoframePrev(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->AVIInfoframePrev));
+}
+
+/* Clear on read */
+bool IsAVIInfoFrameChanged(XV_HdmiRxSs *InstancePtr) {
+	bool status = false;
+
+	status = InstancePtr->AVIInfoChanged;
+	InstancePtr->AVIInfoChanged = false;
+
+	return status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS General Control Packet
+* structure
+*
+* @param  InstancePtr pointer to XV_HdmiRXSs instance
+*
+* @return XHdmiC_GeneralControlPacket pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_GeneralControlPacket *XV_HdmiRxSs_GetGCP(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->GCP));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS Audio InfoFrame structure
+*
+* @param  InstancePtr pointer to XV_HdmiRXSs instance
+*
+* @return XHdmiC_AudioInfoFrame pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_AudioInfoFrame *XV_HdmiRxSs_GetAudioInfoframe(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->AudioInfoframe));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS Vendor Specific InfoFrame
+* structure
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return XHdmiC_VSIF pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_VSIF *XV_HdmiRxSs_GetVSIF(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->VSIF));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS DRM InfoFrame
+* structure
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return struct v4l2_hdr10_payload pointer
+*
+* @note   None.
+*
+******************************************************************************/
+struct v4l2_hdr10_payload *XV_HdmiRxSs_GetDrmInfoframe(XV_HdmiRxSs *InstancePtr)
+{
+    return (&(InstancePtr->DrmInfoframe));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function set HDMI RX susbsystem stream parameters
+*
+* @param  None.
+*
+* @return Calculated TMDS Clock
+*
+* @note   None.
+*
+******************************************************************************/
+u32 XV_HdmiRxSs_SetStream(XV_HdmiRxSs *InstancePtr,
+        u32 Clock, u32 LineRate)
+{
+
+    LineRate = LineRate;
+
+    if (Clock == 0) {
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  /* Write log */
+  XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_SETSTREAM_ERR, 0);
+#endif
+
+        return (XST_FAILURE);
+    }
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  /* Write log */
+  XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_SETSTREAM, 0);
+#endif
+  /* Set stream */
+  XV_HdmiRx_SetStream(InstancePtr->HdmiRxPtr, InstancePtr->Config.Ppc, Clock);
+
+  /* In case the TMDS clock ratio is 1/40 */
+  /* The reference clock must be compensated */
+  if (XV_HdmiRx_GetTmdsClockRatio(InstancePtr->HdmiRxPtr)) {
+      InstancePtr->HdmiRxPtr->Stream.RefClk =
+                   InstancePtr->HdmiRxPtr->Stream.RefClk * 4;
+  }
+
+  return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS video stream
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return XVidC_VideoStream pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XVidC_VideoStream *XV_HdmiRxSs_GetVideoStream(XV_HdmiRxSs *InstancePtr)
+{
+    return (&InstancePtr->HdmiRxPtr->Stream.Video);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS video Identification code
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return VIC
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XV_HdmiRxSs_GetVideoIDCode(XV_HdmiRxSs *InstancePtr)
+{
+    return (InstancePtr->HdmiRxPtr->Stream.Vic);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS video stream type
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return Stream Type  1:HDMI 0:DVI
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XV_HdmiRxSs_GetVideoStreamType(XV_HdmiRxSs *InstancePtr)
+{
+    return (InstancePtr->HdmiRxPtr->Stream.IsHdmi);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI RX SS video stream type
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return Stream Type  1:IsScrambled 0: not Scrambled
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XV_HdmiRxSs_GetVideoStreamScramblingFlag(XV_HdmiRxSs *InstancePtr)
+{
+    return (InstancePtr->HdmiRxPtr->Stream.IsScrambled);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the HDMI RX SS number of active audio channels
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return Channels
+*
+* @note   None.
+*
+******************************************************************************/
+u8 XV_HdmiRxSs_GetAudioChannels(XV_HdmiRxSs *InstancePtr)
+{
+    return (InstancePtr->AudioChannels);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the HDMI RX SS audio format
+*
+* @param  InstancePtr pointer to XV_HdmiRxSs instance
+*
+* @return Channels
+*
+* @note   None.
+*
+******************************************************************************/
+XV_HdmiRx_AudioFormatType XV_HdmiRxSs_GetAudioFormat(XV_HdmiRxSs *InstancePtr)
+{
+    return ((XV_HdmiRx_AudioFormatType)(InstancePtr->HdmiRxPtr->AudFormat));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when HDMI RX SS TMDS clock changes
+*
+* @param  None.
+*
+* @return None
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_RefClockChangeInit(XV_HdmiRxSs *InstancePtr)
+{
+  // Set TMDS Clock ratio
+  InstancePtr->TMDSClockRatio =
+    XV_HdmiRx_GetTmdsClockRatio(InstancePtr->HdmiRxPtr);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_REFCLOCKCHANGE, 0);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI RX SS timing information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ReportTiming(XV_HdmiRxSs *InstancePtr)
+{
+    // Check is the RX stream is up
+    if (XV_HdmiRx_IsStreamUp(InstancePtr->HdmiRxPtr)) {
+        XV_HdmiRx_DebugInfo(InstancePtr->HdmiRxPtr);
+        xil_printf("VIC: %0d\r\n", InstancePtr->HdmiRxPtr->Stream.Vic);
+        xil_printf("Scrambled: %0d\r\n",
+            (XV_HdmiRx_IsStreamScrambled(InstancePtr->HdmiRxPtr)));
+    }
+
+    // No stream
+    else {
+      xil_printf("No HDMI RX stream\r\n");
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reports the link quality based on the link error counter
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ReportLinkQuality(XV_HdmiRxSs *InstancePtr)
+{
+  u8 Channel;
+  u32 Errors;
+
+  for (Channel = 0; Channel < 3; Channel++)
+  {
+      Errors = XV_HdmiRx_GetLinkStatus(InstancePtr->HdmiRxPtr, Channel);
+
+      xil_printf("Link quality channel %0d : ", Channel);
+
+      if (Errors == 0) {
+        xil_printf("excellent");
+      }
+
+      else if ((Errors > 0) && (Errors < 1024)) {
+        xil_printf("good");
+      }
+
+      else if ((Errors > 1024) && (Errors < 16384)) {
+        xil_printf("average");
+      }
+
+      else {
+        xil_printf("bad");
+      }
+
+      xil_printf(" (%0d)\r\n", Errors);
+  }
+
+  /* Clear link error counters */
+  XV_HdmiRx_ClearLinkStatus(InstancePtr->HdmiRxPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI RX SS DRM If information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ReportDRMInfo(XV_HdmiRxSs *InstancePtr)
+{
+	struct v4l2_hdr10_payload *DrmInfoFramePtr;
+	DrmInfoFramePtr = XV_HdmiRxSs_GetDrmInfoframe(InstancePtr);
+
+
+	if (DrmInfoFramePtr->eotf != 0xFF)
+		xil_printf("eotf: %d\r\n", DrmInfoFramePtr->eotf);
+
+	if (DrmInfoFramePtr->metadata_type == 0xFF) {
+		xil_printf("No DRM info\r\n");
+		return;
+	}
+
+	xil_printf("DRM IF info:\n");
+	xil_printf("desc id: %d\r\n", DrmInfoFramePtr->metadata_type);
+	xil_printf("display primaries x0, y0, x1, y1, x2, y2: %d %d %d %d %d %d\r\n",
+			DrmInfoFramePtr->display_primaries[0].x, DrmInfoFramePtr->display_primaries[0].y,
+			DrmInfoFramePtr->display_primaries[1].x, DrmInfoFramePtr->display_primaries[1].y,
+			DrmInfoFramePtr->display_primaries[2].x, DrmInfoFramePtr->display_primaries[2].y
+		  );
+	xil_printf("white point x, y: %d %d\r\n",
+			DrmInfoFramePtr->white_point.x, DrmInfoFramePtr->white_point.y);
+	xil_printf("min/max display mastering luminance: %d %d\r\n",
+			DrmInfoFramePtr->min_mdl,
+			DrmInfoFramePtr->max_mdl);
+	xil_printf("Max_CLL: %d\r\n", DrmInfoFramePtr->max_cll);
+	xil_printf("max_fall: %d\r\n", DrmInfoFramePtr->max_fall);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI RX SS audio information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ReportAudio(XV_HdmiRxSs *InstancePtr)
+{
+  xil_printf("Format   : ");
+  switch (XV_HdmiRxSs_GetAudioFormat(InstancePtr)) {
+	  case 0:
+		xil_printf("Unknown\r\n");
+		break;
+	  case 1:
+		xil_printf("L-PCM\r\n");
+		break;
+	  case 2:
+		xil_printf("HBR\r\n");
+		break;
+	  case 3:
+		xil_printf("3D\r\n");
+		break;
+	  default:
+		break;
+  }
+  xil_printf("Channels : %d\r\n",
+  XV_HdmiRx_GetAudioChannels(InstancePtr->HdmiRxPtr));
+  xil_printf("ACR CTS  : %d\r\n", XV_HdmiRx_GetAcrCts(InstancePtr->HdmiRxPtr));
+  xil_printf("ACR N    : %d\r\n", XV_HdmiRx_GetAcrN(InstancePtr->HdmiRxPtr));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI RX SS audio information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ReportInfoFrame(XV_HdmiRxSs *InstancePtr)
+{
+  xil_printf("RX header: %0x\r\n", InstancePtr->HdmiRxPtr->Aux.Header.Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI RX SS subcore versions
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_ReportSubcoreVersion(XV_HdmiRxSs *InstancePtr)
+{
+  u32 Data;
+
+  if(InstancePtr->HdmiRxPtr)
+  {
+     Data = XV_HdmiRx_GetVersion(InstancePtr->HdmiRxPtr);
+     xil_printf("  HDMI RX version : %02d.%02d (%04x)\r\n",
+     ((Data >> 24) & 0xFF), ((Data >> 16) & 0xFF), (Data & 0xFFFF));
+  }
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if (InstancePtr->Hdcp14Ptr){
+     Data = XHdcp1x_GetVersion(InstancePtr->Hdcp14Ptr);
+     xil_printf("  HDCP 1.4 RX version : %02d.%02d (%04x)\r\n",
+        ((Data >> 24) & 0xFF), ((Data >> 16) & 0xFF), (Data & 0xFFFF));
+  }
+#endif
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function checks if the video stream is up.
+*
+* @param  None.
+*
+* @return
+*   - TRUE if stream is up.
+*   - FALSE if stream is down.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_IsStreamUp(XV_HdmiRxSs *InstancePtr)
+{
+  return (InstancePtr->IsStreamUp);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function checks if the interface is connected.
+*
+* @param  None.
+*
+* @return
+*   - TRUE if interface is connected.
+*   - FALSE if interface is not connected.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_IsStreamConnected(XV_HdmiRxSs *InstancePtr)
+{
+  return (InstancePtr->IsStreamConnected);
+}
+
+/******************************************************************************/
+/**
+*
+* This function configures the Bridge for YUV420 functionality and repeater
+*
+* @param InstancePtr  Instance Pointer to the main data structure
+* @param None
+*
+* @return
+*
+* @note
+*   None.
+*
+******************************************************************************/
+static void XV_HdmiRxSs_ConfigBridgeMode(XV_HdmiRxSs *InstancePtr) {
+    XVidC_VideoStream *HdmiRxSsVidStreamPtr;
+    HdmiRxSsVidStreamPtr = XV_HdmiRxSs_GetVideoStream(InstancePtr);
+
+    XHdmiC_AVI_InfoFrame *AviInfoFramePtr;
+    AviInfoFramePtr = XV_HdmiRxSs_GetAviInfoframe(InstancePtr);
+
+    if ((!InstancePtr->HdmiRxPtr->Stream.IsHdmi) &&
+		    HdmiRxSsVidStreamPtr->IsInterlaced) {
+	if ((HdmiRxSsVidStreamPtr->Timing.HActive == 1440) &&
+			((HdmiRxSsVidStreamPtr->Timing.VActive == 288) ||
+			 (HdmiRxSsVidStreamPtr->Timing.VActive == 240))) {
+             XV_HdmiRxSs_BridgeYuv420(InstancePtr, FALSE);
+             XV_HdmiRxSs_BridgePixelDrop(InstancePtr, TRUE);
+
+	     return;
+	}
+    }
+
+    // Pixel Repetition factor of 3 and above are not supported by the bridge
+    if (AviInfoFramePtr->PixelRepetition > XHDMIC_PIXEL_REPETITION_FACTOR_2) {
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    	XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_PIX_REPEAT_ERR,
+    			AviInfoFramePtr->PixelRepetition);
+#endif
+
+    	return;
+    }
+
+    if (HdmiRxSsVidStreamPtr->ColorFormatId == XVIDC_CSF_YCRCB_420) {
+        /*********************************************************
+         * 420 Support
+         *********************************************************/
+         XV_HdmiRxSs_BridgePixelDrop(InstancePtr, FALSE);
+         XV_HdmiRxSs_BridgeYuv420(InstancePtr, TRUE);
+    }
+    else {
+        if (AviInfoFramePtr->PixelRepetition ==
+				XHDMIC_PIXEL_REPETITION_FACTOR_2)
+        {
+            /*********************************************************
+             * NTSC/PAL Support
+             *********************************************************/
+             XV_HdmiRxSs_BridgeYuv420(InstancePtr, FALSE);
+             XV_HdmiRxSs_BridgePixelDrop(InstancePtr, TRUE);
+        }
+        else {
+            XV_HdmiRxSs_BridgeYuv420(InstancePtr, FALSE);
+            XV_HdmiRxSs_BridgePixelDrop(InstancePtr, FALSE);
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function will set the default in HDF.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRxSs core instance.
+* @param    Id is the XV_HdmiRxSs ID to operate on.
+*
+* @return   None.
+*
+* @note     Linux - No need to put definition inside.
+*
+******************************************************************************/
+void XV_HdmiRxSs_SetDefaultPpc(XV_HdmiRxSs *InstancePtr, u8 Id) {
+
+}
+
+/*****************************************************************************/
+/**
+* This function will set PPC specified by user.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRxSs core instance.
+* @param    Id is the XV_HdmiRxSs ID to operate on.
+* @param    Ppc is the PPC to be set.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_SetPpc(XV_HdmiRxSs *InstancePtr, u8 Id, u8 Ppc) {
+    InstancePtr->Config.Ppc = (XVidC_PixelsPerClock) Ppc;
+    Id = Id; //squash unused variable compiler warning
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI RX SS information to passed buffer
+*
+* @param	InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	buff Buffer to print to
+* @param	buff_size size off buff passed
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_ShowInfo(XV_HdmiRxSs *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+	u8 Channel;
+	u32 Errors;
+	const char* AudioFormatStr[] = {"Unknown", "L-PCM", "HBR"};
+	XV_HdmiRx_AudioFormatType AudioFormat = 0;
+	struct v4l2_hdr10_payload *DrmInfoFramePtr =
+			XV_HdmiRxSs_GetDrmInfoframe(InstancePtr);
+
+	strSize = scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nRx Info\r\n" \
+				"--------\r\n");
+
+    if (InstancePtr->HdmiRxPtr->Stream.IsHdmi == (TRUE)) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Mode: HDMI\r\n");
+    } else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Mode: DVI\r\n");
+    }
+
+    if (XV_HdmiRx_IsStreamUp(InstancePtr->HdmiRxPtr)) {
+		AudioFormat = XV_HdmiRxSs_GetAudioFormat(InstancePtr);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"VIC : %0d\r\n", InstancePtr->HdmiRxPtr->Stream.Vic);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Scrambled: %0d\r\n",
+				(XV_HdmiRx_IsStreamScrambled(InstancePtr->HdmiRxPtr)));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nAudio\r\n" \
+				"------\r\n");
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Format   : %s\r\n",
+				((AudioFormat < 3) ? AudioFormatStr[AudioFormat]
+								  : "Invalid"));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Channels : %d\r\n",
+				XV_HdmiRx_GetAudioChannels(InstancePtr->HdmiRxPtr));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ACR CTS  : %d\r\n",
+				XV_HdmiRx_GetAcrCts(InstancePtr->HdmiRxPtr));
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"ACR N    : %d\r\n\r\n",
+				XV_HdmiRx_GetAcrN(InstancePtr->HdmiRxPtr));
+    } else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"Status: No input stream detected\r\n");
+	}
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nLink quality\r\n" \
+				"------------\r\n");
+	for (Channel = 0; Channel < 3; Channel++)
+	{
+		Errors = XV_HdmiRx_GetLinkStatus(InstancePtr->HdmiRxPtr, Channel);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"Link quality channel %0d : ", Channel);
+
+		if (Errors == 0) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"excellent");
+		} else if ((Errors > 0) && (Errors < 1024)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"good");
+		} else if ((Errors > 1024) && (Errors < 16384)) {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"average");
+		} else {
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"bad");
+		}
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			" (%0d)\r\n", Errors);
+	}
+
+	if (DrmInfoFramePtr->eotf != 0xFF) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"eotf: %d\r\n", DrmInfoFramePtr->eotf);
+	}
+
+	if (DrmInfoFramePtr->metadata_type == 0xFF) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nNo DRM info\r\n");
+	} else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nDRM IF Info\r\n" \
+				"------------\r\n");
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"desc id: %d\r\n", DrmInfoFramePtr->metadata_type);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"display primaries x0, y0, x1, y1, x2, y2: %d %d %d %d %d %d\r\n",
+				DrmInfoFramePtr->display_primaries[0].x, DrmInfoFramePtr->display_primaries[0].y,
+				DrmInfoFramePtr->display_primaries[1].x, DrmInfoFramePtr->display_primaries[1].y,
+				DrmInfoFramePtr->display_primaries[2].x, DrmInfoFramePtr->display_primaries[2].y);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"white point x, y: %d %d\r\n",
+				DrmInfoFramePtr->white_point.x, DrmInfoFramePtr->white_point.y);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"min/max display mastering luminance: %d %d\r\n",
+				DrmInfoFramePtr->min_mdl,
+				DrmInfoFramePtr->max_mdl);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"max_cll: %d\r\n", DrmInfoFramePtr->max_cll);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"max_fall: %d\r\n", DrmInfoFramePtr->max_fall);
+	}
+
+	/* Clear link error counters */
+	XV_HdmiRx_ClearLinkStatus(InstancePtr->HdmiRxPtr);
+
+  return strSize;
+}
+
+/*
+* This function set HDMI RX audio parameters
+*
+* @param  Enable 0: Unmute the audio 1: Mute the audio.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_AudioMute(XV_HdmiRxSs *InstancePtr, u8 Enable)
+{
+  //Audio Mute Mode
+  if (Enable){
+	XV_HdmiRx_AudioDisable(InstancePtr->HdmiRxPtr);
+  }
+  else{
+	XV_HdmiRx_AudioEnable(InstancePtr->HdmiRxPtr);
+  }
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss.h
@@ -0,0 +1,598 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirxss.h
+*
+* This is main header file of the Xilinx HDMI RX Subsystem driver
+*
+* <b>HDMI RX Subsystem Overview</b>
+*
+* Video Subsystem is a collection of IP cores bounded together by software
+* to provide an abstract view of the processing pipe. It hides all the
+* complexities of programming the underlying cores from end user.
+*
+* <b>Subsystem Driver Features</b>
+*
+* Video Subsystem supports following features
+*   - AXI Stream Input/Output interface
+*   - 1, 2 or 4 pixel-wide video interface
+*   - 8/10/12/16 bits per component
+*   - RGB & YCbCr color space
+*   - Up to 4k2k 60Hz resolution at both Input and Output interface
+*   - Interlaced input support (1080i 50Hz/60Hz)
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     20/01/16 Added remapper support
+* 1.2   yh     01/02/16 Added set_ppc api
+* 1.3   MG     03/02/16 Added HDCP support
+* 1.4   MH     03/15/16 Added HDCP connect event.
+*                       Added HDCP authenticated callback support.
+* 1.5   YH     17/03/16 Remove xintc.h as it is processor dependent
+* 1.6   MH     23/06/16 Added HDCP repeater support.
+* 1.7   YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+* 1.8   MH     26/07/16 Updates for automatic protocol switching
+* 1.9   MH     05/08/16 Updates to optimize out HDCP when excluded
+* 1.10  YH     18/08/16 Combine Report function into one ReportInfo
+* 1.11  YH     14/11/16 Added API to enable/disable YUV420/Pixel Drop Mode
+*                       for video bridge
+* 1.15  YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.16  MMO    03/01/17 Add compiler option(XV_HDMIRXSS_LOG_ENABLE) to enable
+*                         Log
+*						Re-order the enumaration and data structure
+*                       Move HDCP local API into _hdcp.h
+*       ms     03/17/17 Added readme.txt file in examples folder for doxygen
+*                       generation.
+*       ms     04/10/17 Modified filename tag in examples to include them in
+*                        doxygen.
+* 1.4   YH     07/07/17 Add new log type XV_HDMIRXSS_LOG_EVT_SETSTREAM_ERR
+*       MH     09/08/17 Add function XV_HdmiRxSs_HdcpSetCapability
+*       YH     06/10/17 Add function XV_HdmiRxSs_GetAudioFormat
+* 5.0   YH     16/11/17 Added dedicated reset for each clock domain
+*              16/11/17 Added bridge overflow interrupt
+*       EB     16/01/18 Added InfoFrame data structure to XV_HdmiRxSs
+*                       Added XV_HDMIRXSS_LOG_EVT_PIX_REPEAT_ERR log event
+*                       Added functions XV_HdmiRxSs_GetAviInfoframe,
+*                           XV_HdmiRxSs_GetGCP, XV_HdmiRxSs_GetAudioInfoframe,
+*                           XV_HdmiRxSs_GetVSIF
+* 5.2   YB     08/14/18 Added dedicated callbacks for HDCP 1.4 and HDCP 2.2
+*                           protocol events.
+*       EB     03/08/18 Added function XV_HdmiRxSs_AudioMute
+*                       Added TMDS Clock Ratio callback support
+*       YB     17/08/18 Marked XV_HDMIRXSS_HDCP_1_PROT_EVT and
+*                           XV_HDMIRXSS_HDCP_2_PROT_EVT as deprecated.
+* 5.40  EB     06/08/19 Added Vic and Video Timing mismatch callback support
+* </pre>
+*
+******************************************************************************/
+
+#ifndef HDMIRXSS_H /**< prevent circular inclusions by using protection macros*/
+#define HDMIRXSS_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xstatus.h"
+#include "xv_hdmirx.h"
+#include "xv_hdmic_vsif.h"
+#if !defined(XV_CONFIG_LOG_VHDMIRXSS_DISABLE) && \
+    !defined(XV_CONFIG_LOG_DISABLE_ALL)
+#define XV_HDMIRXSS_LOG_ENABLE
+#endif
+
+#if defined(XPAR_XHDCP_NUM_INSTANCES) || defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+#define USE_HDCP_RX
+#define USE_HDCP_14_PROT_EVT_ENUM
+#pragma message ("'XV_HDMIRXSS_HDCP_1_PROT_EVT' event is deprecated")
+#define USE_HDCP_22_PROT_EVT_ENUM
+#pragma message ("'XV_HDMIRXSS_HDCP_2_PROT_EVT' event is deprecated")
+#define XV_HDMIRXSS_HDCP_KEYSEL 0x00u
+#define XV_HDMIRXSS_HDCP_MAX_QUEUE_SIZE 16
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+#include "xtmrctr.h"
+#include "xhdcp1x.h"
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+#include "xhdcp22_rx.h"
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+/*****************************************************************************/
+/**
+* This macros selects the bridge YUV420 mode
+*
+* @param  InstancePtr is a pointer to the HDMI RX Subsystem
+*
+*****************************************************************************/
+#define XV_HdmiRxSs_BridgeYuv420(InstancePtr,Enable) \
+{ \
+    XV_HdmiRx_Bridge_yuv420(InstancePtr->HdmiRxPtr, Enable); \
+} \
+
+/*****************************************************************************/
+/**
+* This macros selects the bridge pixel repeat mode
+*
+* @param  InstancePtr is a pointer to the HDMI RX Subsystem
+*
+*****************************************************************************/
+#define XV_HdmiRxSs_BridgePixelDrop(InstancePtr,Enable) \
+{ \
+    XV_HdmiRx_Bridge_pixel(InstancePtr->HdmiRxPtr, Enable); \
+}
+
+/****************************** Type Definitions ******************************/
+/** @name Handler Types
+* @{
+*/
+
+#define ANSI_COLOR_RED     "\x1b[31m"
+#define ANSI_COLOR_YELLOW  "\x1b[33m"
+#define ANSI_COLOR_RESET   "\x1b[0m"
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+typedef enum {
+	XV_HDMIRXSS_LOG_EVT_NONE = 1,		/**< Log event none. */
+	XV_HDMIRXSS_LOG_EVT_HDMIRX_INIT,	/**< Log event HDMIRX Init. */
+	XV_HDMIRXSS_LOG_EVT_VTC_INIT,	    /**< Log event VTC Init. */
+	XV_HDMIRXSS_LOG_EVT_HDCPTIMER_INIT,	/**< Log event HDCP Timer Init */
+	XV_HDMIRXSS_LOG_EVT_HDCP14_INIT,	/**< Log event HDCP 14 Init. */
+	XV_HDMIRXSS_LOG_EVT_HDCP22_INIT,	/**< Log event HDCP 22 Init. */
+	XV_HDMIRXSS_LOG_EVT_START,	        /**< Log event HDMIRXSS Start. */
+	XV_HDMIRXSS_LOG_EVT_STOP,	        /**< Log event HDMIRXSS Stop. */
+	XV_HDMIRXSS_LOG_EVT_RESET,	        /**< Log event HDMIRXSS Reset. */
+	XV_HDMIRXSS_LOG_EVT_CONNECT,        /**< Log event Cable connect. */
+	XV_HDMIRXSS_LOG_EVT_DISCONNECT,	    /**< Log event Cable disconnect. */
+	XV_HDMIRXSS_LOG_EVT_LINKSTATUS,     /**< Log event Link Status Error. */
+	XV_HDMIRXSS_LOG_EVT_STREAMUP,	    /**< Log event Stream Up. */
+	XV_HDMIRXSS_LOG_EVT_STREAMDOWN,	    /**< Log event Stream Down. */
+	XV_HDMIRXSS_LOG_EVT_STREAMINIT,	    /**< Log event Stream Init. */
+	XV_HDMIRXSS_LOG_EVT_SETSTREAM,      /**< Log event HDMIRXSS Setstream. */
+	XV_HDMIRXSS_LOG_EVT_SETSTREAM_ERR,  /**< Log event HDMIRXSS Setstream Err. */
+	XV_HDMIRXSS_LOG_EVT_REFCLOCKCHANGE, /**< Log event TMDS Ref clock change. */
+	XV_HDMIRXSS_LOG_EVT_HDCP14,             /**< Log event Enable HDCP 1.4. */
+	XV_HDMIRXSS_LOG_EVT_HDCP22,             /**< Log event Enable HDCP 2.2. */
+	XV_HDMIRXSS_LOG_EVT_HDMIMODE,           /**< Log event HDMI Mode change. */
+	XV_HDMIRXSS_LOG_EVT_DVIMODE,            /**< Log event HDMI Mode change. */
+	XV_HDMIRXSS_LOG_EVT_SYNCLOSS,           /**< Log event Sync Loss detected. */
+	XV_HDMIRXSS_LOG_EVT_PIX_REPEAT_ERR,		/**< Log event Unsupported Pixel Repetition. */
+	XV_HDMIRXSS_LOG_EVT_SYNCEST,            /**< Log event Sync Loss detected. */
+	XV_HDMIRXSS_LOG_EVT_VICERROR,           /**< Log event vic error detected. */
+	XV_HDMIRXSS_LOG_EVT_DUMMY               /**< Dummy Event should be last */
+} XV_HdmiRxSs_LogEvent;
+
+/**
+ * This typedef contains the logging mechanism for debug.
+ */
+typedef struct {
+	u16 DataBuffer[256];		/**< Log buffer with event data. */
+	u8 HeadIndex;			/**< Index of the head entry of the
+						Event/DataBuffer. */
+	u8 TailIndex;			/**< Index of the tail entry of the
+						Event/DataBuffer. */
+} XV_HdmiRxSs_Log;
+#endif
+
+#ifdef USE_HDCP_RX
+/**
+* These constants are used to identify fields inside the topology structure
+*/
+typedef enum {
+  XV_HDMIRXSS_HDCP_TOPOLOGY_DEPTH,
+  XV_HDMIRXSS_HDCP_TOPOLOGY_DEVICECNT,
+  XV_HDMIRXSS_HDCP_TOPOLOGY_MAXDEVSEXCEEDED,
+  XV_HDMIRXSS_HDCP_TOPOLOGY_MAXCASCADEEXCEEDED,
+  XV_HDMIRXSS_HDCP_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM,
+  XV_HDMIRXSS_HDCP_TOPOLOGY_HDCP1DEVICEDOWNSTREAM,
+  XV_HDMIRXSS_HDCP_TOPOLOGY_INVALID
+} XV_HdmiRxSs_HdcpTopologyField;
+
+/**
+* These constants specify the HDCP Events
+*/
+typedef enum
+{
+  XV_HDMIRXSS_HDCP_NO_EVT,
+  XV_HDMIRXSS_HDCP_STREAMUP_EVT,
+  XV_HDMIRXSS_HDCP_STREAMDOWN_EVT,
+  XV_HDMIRXSS_HDCP_CONNECT_EVT,
+  XV_HDMIRXSS_HDCP_DISCONNECT_EVT,
+#ifdef USE_HDCP_14_PROT_EVT_ENUM
+  XV_HDMIRXSS_HDCP_1_PROT_EVT,
+#endif
+#ifdef USE_HDCP_22_PROT_EVT_ENUM
+  XV_HDMIRXSS_HDCP_2_PROT_EVT,
+#endif
+  XV_HDMIRXSS_HDCP_DVI_MODE_EVT,
+  XV_HDMIRXSS_HDCP_HDMI_MODE_EVT,
+  XV_HDMIRXSS_HDCP_SYNC_LOSS_EVT,
+  XV_HDMIRXSS_HDCP_SYNC_EST_EVT,
+  XV_HDMIRXSS_HDCP_INVALID_EVT
+} XV_HdmiRxSs_HdcpEvent;
+
+/**
+* These constants specify the HDCP key types
+*/
+typedef enum
+{
+  XV_HDMIRXSS_KEY_HDCP22_LC128,     /**< HDCP 2.2 LC128 */
+  XV_HDMIRXSS_KEY_HDCP22_PRIVATE,   /**< HDCP 2.2 Private */
+  XV_HDMIRXSS_KEY_HDCP14,           /**< HDCP 1.4 Key */
+} XV_HdmiRxSs_HdcpKeyType;
+
+/**
+* These constants specify HDCP repeater content stream management type
+*/
+typedef enum
+{
+  XV_HDMIRXSS_HDCP_STREAMTYPE_0, /**< HDCP Stream Type 0 */
+  XV_HDMIRXSS_HDCP_STREAMTYPE_1  /**< HDCP Stream Type 1 */
+} XV_HdmiRxSs_HdcpContentStreamType;
+
+typedef struct
+{
+  XV_HdmiRxSs_HdcpEvent Queue[XV_HDMIRXSS_HDCP_MAX_QUEUE_SIZE]; /**< Data */
+  u8                    Tail;      /**< Tail pointer */
+  u8                    Head;      /**< Head pointer */
+} XV_HdmiRxSs_HdcpEventQueue;
+#endif
+
+/**
+* These constants specify the HDCP protection schemes
+*/
+typedef enum
+{
+  XV_HDMIRXSS_HDCP_NONE,       /**< No content protection */
+  XV_HDMIRXSS_HDCP_14,         /**< HDCP 1.4 */
+  XV_HDMIRXSS_HDCP_22,         /**< HDCP 2.2 */
+  XV_HDMIRXSS_HDCP_BOTH,       /**< Both HDCP 1.4 and 2.2 */
+  XV_HDMIRXSS_HDCP_NOUSERPREF,       /**< Control user selection.
+				       * to be used only with API
+				       * XV_HdmiRxSs_SetUserHdcpProtocol */
+} XV_HdmiRxSs_HdcpProtocol;
+
+/**
+* These constants specify different types of handler and used to differentiate
+* interrupt requests from peripheral.
+*/
+typedef enum {
+  XV_HDMIRXSS_HANDLER_CONNECT = 1,                  /**< Handler for connect
+                                                         event */
+  XV_HDMIRXSS_HANDLER_BRDGOVERFLOW,                 /**< Handler for
+                                                         bridge fifo overflow
+                                                         event */
+  XV_HDMIRXSS_HANDLER_AUX,                          /**< Handler for AUX
+                                                         peripheral event */
+  XV_HDMIRXSS_HANDLER_AUD,                          /**< Handler for AUD
+                                                         peripheral event */
+  XV_HDMIRXSS_HANDLER_LNKSTA,                       /**< Handler for LNKSTA
+                                                         peripheral event */
+  XV_HDMIRXSS_HANDLER_DDC,                          /**< Handler for DDC
+                                                         peripheral event */
+  XV_HDMIRXSS_HANDLER_STREAM_DOWN,                  /**< Handler for stream
+                                                         down event */
+  XV_HDMIRXSS_HANDLER_STREAM_INIT,                  /**< Handler for stream
+                                                         init event */
+  XV_HDMIRXSS_HANDLER_STREAM_UP,                    /**< Handler for stream up
+                                                         event */
+  XV_HDMIRXSS_HANDLER_HDCP,                         /**< Handler for HDCP 1.4
+                                                         event */
+  XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATED,           /**< Handler for HDCP
+                                                         authenticated event */
+  XV_HDMIRXSS_HANDLER_HDCP_UNAUTHENTICATED,         /**< Handler for HDCP
+                                                         unauthenticated event*/
+  XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATION_REQUEST,  /**< Handler for HDCP
+                                                         authentication request
+                                                         event */
+  XV_HDMIRXSS_HANDLER_HDCP_STREAM_MANAGE_REQUEST,   /**< Handler for HDCP stream
+                                                         manage request event */
+  XV_HDMIRXSS_HANDLER_HDCP_TOPOLOGY_UPDATE,         /**< Handler for HDCP
+                                                         topology update event*/
+  XV_HDMIRXSS_HANDLER_HDCP_ENCRYPTION_UPDATE,       /**< Handler for HDCP
+                                                         encryption status
+                                                         update event */
+  XV_HDMIRXSS_HANDLER_TMDS_CLK_RATIO,               /**< Handler type for
+                                                         TMDS clock ratio
+                                                         change */
+  XV_HDMIRXSS_HANDLER_VIC_ERROR                     /**< Handler type for
+                                                         VIC error change */
+} XV_HdmiRxSs_HandlerType;
+/*@}*/
+
+/**
+ * Sub-Core Configuration Table
+ */
+typedef struct
+{
+  u16 IsPresent;  /**< Flag to indicate if sub-core is present in the design*/
+  u16 DeviceId;   /**< Device ID of the sub-core */
+  UINTPTR AbsAddr; /**< Absolute Base Address of hte Sub-cores*/
+}XV_HdmiRxSs_SubCore;
+
+/**
+ * Video Processing Subsystem configuration structure.
+ * Each subsystem device should have a configuration structure associated
+ * that defines the MAX supported sub-cores within subsystem
+ */
+
+typedef struct
+{
+  u16 DeviceId;     /**< DeviceId is the unique ID  of the device */
+  UINTPTR BaseAddress;  /**< BaseAddress is the physical base address of the
+                        subsystem address range */
+  UINTPTR HighAddress;  /**< HighAddress is the physical MAX address of the
+                        subsystem address range */
+  XVidC_PixelsPerClock Ppc;         /**< Supported Pixel per Clock */
+  u8 MaxBitsPerPixel;               /**< Maximum  Supported Color Depth */
+  XV_HdmiRxSs_SubCore HdcpTimer;    /**< Sub-core instance configuration */
+  XV_HdmiRxSs_SubCore Hdcp14;       /**< Sub-core instance configuration */
+  XV_HdmiRxSs_SubCore Hdcp22;       /**< Sub-core instance configuration */
+  XV_HdmiRxSs_SubCore HdmiRx;       /**< Sub-core instance configuration */
+} XV_HdmiRxSs_Config;
+
+/**
+* Callback type for interrupt.
+*
+* @param  CallbackRef is a callback reference passed in by the upper
+*   layer when setting the callback functions, and passed back to
+*   the upper layer when the callback is invoked.
+*
+* @return None.
+*
+* @note   None.
+*
+*/
+typedef void (*XV_HdmiRxSs_Callback)(void *CallbackRef);
+
+/**
+* The XVprocss driver instance data. The user is required to allocate a variable
+* of this type for every XVprocss device in the system. A pointer to a variable
+* of this type is then passed to the driver API functions.
+*/
+typedef struct
+{
+  XV_HdmiRxSs_Config Config;    /**< Hardware configuration */
+  u32 IsReady;                  /**< Device and the driver instance are
+                                     initialized */
+  u8 AppMajVer;       /**< Major Version of application used by the driver */
+  u8 AppMinVer;       /**< Minor Version of application used by the driver */
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+  XV_HdmiRxSs_Log Log;				/**< A log of events. */
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  XTmrCtr *HdcpTimerPtr;           /**< handle to sub-core driver instance */
+  XHdcp1x *Hdcp14Ptr;                /**< handle to sub-core driver instance */
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  XHdcp22_Rx  *Hdcp22Ptr;           /**< handle to sub-core driver instance */
+#endif
+  XV_HdmiRx *HdmiRxPtr;             /**< handle to sub-core driver instance */
+
+  /*Callbacks */
+  XV_HdmiRxSs_Callback ConnectCallback; /**< Callback for connect event */
+  void *ConnectRef;     /**< To be passed to the connect callback */
+
+  XV_HdmiRxSs_Callback BrdgOverflowCallback;  /**< Callback for Bridge overflow
+                                           event */
+  void *BrdgOverflowRef;         /**< To be passed to the Bridge overflow
+                                    callback */
+
+  XV_HdmiRxSs_Callback AuxCallback;     /**< Callback for AUX event */
+  void *AuxRef;         /**< To be passed to the AUX callback */
+
+  XV_HdmiRxSs_Callback AudCallback;     /**< Callback for AUD event */
+  void *AudRef;         /**< To be passed to the AUD callback */
+
+  XV_HdmiRxSs_Callback LnkStaCallback;  /**< Callback for LNKSTA event */
+  void *LnkStaRef;      /**< To be passed to the LNKSTA callback */
+
+  XV_HdmiRxSs_Callback DdcCallback;     /**< Callback for PDDC event */
+  void *DdcRef;         /**< To be passed to the DDC callback */
+
+  XV_HdmiRxSs_Callback StreamDownCallback;/**< Callback for stream down event */
+  void *StreamDownRef;  /**< To be passed to the stream down callback */
+
+  XV_HdmiRxSs_Callback StreamInitCallback;/**< Callback for stream init event */
+  void *StreamInitRef;  /**< To be passed to the stream init callback */
+
+  XV_HdmiRxSs_Callback StreamUpCallback; /**< Callback for stream up event */
+  void *StreamUpRef;    /**< To be passed to the stream up callback */
+
+  XV_HdmiRxSs_Callback HdcpCallback;    /**< Callback for HDCP 1.4 event */
+  void *HdcpRef;        /**< To be passed to the hdcp callback */
+
+  XV_HdmiRxSs_Callback TmdsClkRatioCallback;  /**< Callback for scdc TMDS clock
+                                                   ratio change callback */
+  void *TmdsClkRatioRef;/**< To be passed to the scdc tmds clock ratio change
+                             callback */
+
+  XV_HdmiRxSs_Callback VicErrorCallback;  /**< Callback for VIC error
+                                               detection */
+   void *VicErrorRef;   /**< To be passed to the VIC error callback */
+
+  // Scratch pad
+  u8 IsStreamConnected;         /**< HDMI RX Stream Connected */
+  u8 IsStreamUp;                /**< HDMI RX Stream Up */
+  u8 AudioChannels;             /**< Number of Audio Channels */
+  int IsLinkStatusErrMax;       /**< Link Error Status Maxed */
+  u8 *EdidPtr;                     /**< Default Edid Pointer */
+  u16 EdidLength;               /**< Default Edid Length */
+  u8 TMDSClockRatio;            /**< HDMI RX TMDS clock ratio */
+
+  XHdmiC_AVI_InfoFrame AVIInfoframe;	/**< AVI InfoFrame */
+  XHdmiC_AVI_InfoFrame AVIInfoframePrev;	/**< AVI InfoFrame */
+  bool AVIInfoChanged;
+  XHdmiC_GeneralControlPacket GCP;		/**< General Control Packet */
+  XHdmiC_AudioInfoFrame AudioInfoframe;	/**< Audio InfoFrame */
+  XHdmiC_VSIF VSIF;						/**< Vendor Specific InfoFrame */
+  struct v4l2_hdr10_payload DrmInfoframe; /* HDR infoframe */
+
+  XVidC_DelayHandler UserTimerWaitUs; /**< Custom user function for
+                                           delay/sleep. */
+  void *UserTimerPtr;                 /**< Pointer to a timer instance
+                                           used by the custom user
+                                           delay/sleep function. */
+
+  XV_HdmiRxSs_HdcpProtocol      HdcpProtocol;   /**< HDCP protocol selected */
+#ifdef USE_HDCP_RX
+  /**< HDCP specific */
+  u32                           HdcpIsReady;    /**< HDCP ready flag */
+  XV_HdmiRxSs_HdcpProtocol	UserHdcpProt;    /**< User HDCP preference */
+  XV_HdmiRxSs_HdcpEventQueue    HdcpEventQueue;         /**< HDCP event queue */
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  u8                            *Hdcp22Lc128Ptr;     /**< Pointer to HDCP 2.2
+                                                         LC128 */
+  u8                            *Hdcp22PrivateKeyPtr;   /**< Pointer to HDCP 2.2
+                                                             Private key */
+#endif
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  u8                            *Hdcp14KeyPtr;   /**< Pointer to HDCP 1.4 key */
+#endif
+} XV_HdmiRxSs;
+
+/************************** Macros Definitions *******************************/
+#ifdef USE_HDCP_RX
+#define XV_HdmiRxSs_HdcpIsReady(InstancePtr) \
+  (InstancePtr)->HdcpIsReady
+#endif
+/************************** Function Prototypes ******************************/
+XV_HdmiRxSs_Config* XV_HdmiRxSs_LookupConfig(u32 DeviceId);
+void XV_HdmiRxSs_SetUserTimerHandler(XV_HdmiRxSs *InstancePtr,
+        XVidC_DelayHandler CallbackFunc, void *CallbackRef);
+void XV_HdmiRxSS_HdmiRxIntrHandler(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_CfgInitialize(XV_HdmiRxSs *InstancePtr,
+    XV_HdmiRxSs_Config *CfgPtr,
+    UINTPTR EffectiveAddr);
+int XV_HdmiRxSs_CfgInitializeHdcp(XV_HdmiRxSs *InstancePtr,
+    XV_HdmiRxSs_Config *CfgPtr,
+    UINTPTR EffectiveAddr);
+void XV_HdmiRxSs_Start(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_Stop(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_Reset(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_RXCore_VRST(XV_HdmiRxSs *InstancePtr, u8 Reset);
+void XV_HdmiRxSs_RXCore_LRST(XV_HdmiRxSs *InstancePtr, u8 Reset);
+void XV_HdmiRxSs_VRST(XV_HdmiRxSs *InstancePtr, u8 Reset);
+void XV_HdmiRxSs_SYSRST(XV_HdmiRxSs *InstancePtr, u8 Reset);
+int XV_HdmiRxSs_SetCallback(XV_HdmiRxSs *InstancePtr,
+		XV_HdmiRxSs_HandlerType HandlerType,
+		void *CallbackFunc,
+		void *CallbackRef);
+void XV_HdmiRxSs_SetEdidParam(XV_HdmiRxSs *InstancePtr, u8 *EdidDataPtr,
+                                                                u16 Length);
+void XV_HdmiRxSs_LoadDefaultEdid(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_LoadEdid(XV_HdmiRxSs *InstancePtr, u8 *EdidDataPtr,
+                                                                u16 Length);
+void XV_HdmiRxSs_SetHpd(XV_HdmiRxSs *InstancePtr, u8 Value);
+void XV_HdmiRxSs_ToggleHpd(XV_HdmiRxSs *InstancePtr);
+XHdmiC_Aux *XV_HdmiRxSs_GetAuxiliary(XV_HdmiRxSs *InstancePtr);
+XHdmiC_AVI_InfoFrame *XV_HdmiRxSs_GetAviInfoframe(XV_HdmiRxSs *InstancePtr);
+XHdmiC_AVI_InfoFrame *XV_HdmiRxSs_GetAviInfoframePrev(XV_HdmiRxSs *InstancePtr);
+bool IsAVIInfoFrameChanged(XV_HdmiRxSs *InstancePtr);
+XHdmiC_AudioInfoFrame *XV_HdmiRxSs_GetAudioInfoframe(XV_HdmiRxSs *InstancePtr);
+struct v4l2_hdr10_payload *XV_HdmiRxSs_GetDrmInfoframe(XV_HdmiRxSs *InstancePtr);
+XHdmiC_VSIF *XV_HdmiRxSs_GetVSIF(XV_HdmiRxSs *InstancePtr);
+XHdmiC_GeneralControlPacket *XV_HdmiRxSs_GetGCP(XV_HdmiRxSs *InstancePtr);
+u32 XV_HdmiRxSs_SetStream(XV_HdmiRxSs *InstancePtr,
+    u32 Clock,
+    u32 LineRate);
+XVidC_VideoStream *XV_HdmiRxSs_GetVideoStream(XV_HdmiRxSs *InstancePtr);
+u8 XV_HdmiRxSs_GetVideoIDCode(XV_HdmiRxSs *InstancePtr);
+u8 XV_HdmiRxSs_GetVideoStreamType(XV_HdmiRxSs *InstancePtr);
+u8 XV_HdmiRxSs_GetVideoStreamScramblingFlag(XV_HdmiRxSs *InstancePtr);
+u8 XV_HdmiRxSs_GetAudioChannels(XV_HdmiRxSs *InstancePtr);
+XV_HdmiRx_AudioFormatType XV_HdmiRxSs_GetAudioFormat(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_RefClockChangeInit(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_ReportInfo(XV_HdmiRxSs *InstancePtr);
+int  XV_HdmiRxSs_IsStreamUp(XV_HdmiRxSs *InstancePtr);
+int  XV_HdmiRxSs_IsStreamConnected(XV_HdmiRxSs *InstancePtr);
+
+void XV_HdmiRxSs_SetDefaultPpc(XV_HdmiRxSs *InstancePtr, u8 Id);
+void XV_HdmiRxSs_SetPpc(XV_HdmiRxSs *InstancePtr, u8 Id, u8 Ppc);
+void XV_HdmiRxSs_AudioMute(XV_HdmiRxSs *InstancePtr, u8 Enable);
+int XV_HdmiRxSs_SetUserHdcpProtocol(XV_HdmiRxSs *InstancePtr,
+		XV_HdmiRxSs_HdcpProtocol protocol);
+
+
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+void XV_HdmiRxSs_LogReset(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSs_LogWrite(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_LogEvent Evt, u8 Data);
+u16 XV_HdmiRxSs_LogRead(XV_HdmiRxSs *InstancePtr);
+#endif
+int XV_HdmiRxSs_LogShow(XV_HdmiRxSs *InstancePtr, char * buff, int buff_size);
+int XV_HdmiRxSs_ShowInfo(XV_HdmiRxSs *InstancePtr, char *buff, int buff_size);
+
+#ifdef USE_HDCP_RX
+void XV_HdmiRxSs_HdcpSetKey(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpKeyType KeyType, u8 *KeyPtr);
+int XV_HdmiRxSs_HdcpEnable(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpDisable(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpClearEvents(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpPushEvent(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpEvent Event);
+int XV_HdmiRxSs_HdcpPoll(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpSetProtocol(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpProtocol Protocol);
+int XV_HdmiRxSs_HdcpSetCapability(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpProtocol Protocol);
+XV_HdmiRxSs_HdcpProtocol XV_HdmiRxSs_HdcpGetProtocol(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsEnabled(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsAuthenticated(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsEncrypted(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsInProgress(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpInfo(XV_HdmiRxSs *InstancePtr, char *buff, int buff_size);
+void XV_HdmiRxSs_HdcpSetInfoDetail(XV_HdmiRxSs *InstancePtr, u8 Verbose);
+int XV_HdmiRxSs_HdcpSetTopology(XV_HdmiRxSs *InstancePtr, void *TopologyPtr);
+int XV_HdmiRxSs_HdcpSetTopologyReceiverIdList(XV_HdmiRxSs *InstancePtr, u8 *ListPtr, u32 ListSize);
+int XV_HdmiRxSs_HdcpSetTopologyField(XV_HdmiRxSs *InstancePtr,
+      XV_HdmiRxSs_HdcpTopologyField Field, u32 Value);
+int XV_HdmiRxSs_HdcpSetRepeater(XV_HdmiRxSs *InstancePtr, u8 Set);
+int XV_HdmiRxSs_HdcpSetTopologyUpdate(XV_HdmiRxSs *InstancePtr);
+XV_HdmiRxSs_HdcpContentStreamType XV_HdmiRxSs_HdcpGetContentStreamType(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsRepeater(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsInWaitforready(XV_HdmiRxSs *InstancePtr);
+int XV_HdmiRxSs_HdcpIsInComputations(XV_HdmiRxSs *InstancePtr);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+int XV_HdmiRxSs_HdcpTimerStart(void *InstancePtr, u16 TimeoutInMs);
+int XV_HdmiRxSs_HdcpTimerStop(void *InstancePtr);
+int XV_HdmiRxSs_HdcpTimerBusyDelay(void *InstancePtr, u16 DelayInMs);
+void XV_HdmiRxSS_HdcpIntrHandler(XV_HdmiRxSs *InstancePtr);
+void XV_HdmiRxSS_HdcpTimerIntrHandler(XV_HdmiRxSs *InstancePtr);
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+void XV_HdmiRxSS_Hdcp22TimerIntrHandler(XV_HdmiRxSs *InstancePtr);
+#endif
+
+#endif // USE_HDCP_RX
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_coreinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_coreinit.c
@@ -0,0 +1,763 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirxss_coreinit.c
+* @{
+* @details
+
+* HDMI RX Subsystem Sub-Cores initialization
+* The functions in this file provides an abstraction from the initialization
+* sequence for included sub-cores. Subsystem is assigned an address and range
+* on the axi-lite interface. This address space is condensed where-in each
+* sub-core is at a fixed offset from the subsystem base address. For processor
+* to be able to access the sub-core this offset needs to be transalted into a
+* absolute address within the subsystems addressable range
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     20/01/16 Added remapper support
+* 1.2   MG     20/01/16 Added HDCP support
+* 1.3   MH     08/03/16 Added DDC read message not complete event to
+*                       the function XV_HdmiRxSs_DdcHdcpCallback.
+*                       Updated XV_HdmiRxSs_LinkErrorCallback
+*                       function to set link error flag.
+* 1.4   MH     23/04/16 Remove XV_HdmiRxSs_Reset from
+*                       function XV_HdmiRxSs_SubcoreInitHdmiRx
+* 1.5   MH     15/07/16 Added HDCP repeater support.
+* 1.6   YH     18/07/16 Replace xil_print with xdbg_printf.
+* 1.7   YH     25/07/16 Used UINTPTR instead of u32 for BaseAddr,HighAddr,Offset
+*                       AbsAddr
+* 1.8   MH     08/08/16 Updates to optimize out HDCP when excluded.
+* 1.9   YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.10  MMO    03/01/17 Remove XV_HdmiRxSs_ComputeSubcoreAbsAddr API, as it
+*                       handles in the "_g" TCL generation
+*                       Move XV_HdmiRx_DdcLoadEdid to xv_hdmirxss.h and call it
+*                       in user application
+*                       Add compiler option(XV_HDMIRXSS_LOG_ENABLE) to enable Log
+* 3.2   MH     04/07/17 Fixed issue to prevent HDCP protocol switching when only
+*                       one protocol is in the design.
+* 5.2   YB     13/08/18 Added XV_HdmiRxSs_DdcHdcp14ProtocolEvtCallback() and
+*                       XV_HdmiRxSs_DdcHdcp22ProtocolEvtCallback() functions.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include "xv_hdmirxss_coreinit.h"
+
+/************************** Constant Definitions *****************************/
+
+/************************** Function Prototypes ******************************/
+#ifdef USE_HDCP_RX
+static void XV_HdmiRxSs_DdcSetRegAddrHandler(void *RefPtr, u32 Data);
+static void XV_HdmiRxSs_DdcSetRegDataHandler(void *RefPtr, u32 Data);
+static u32 XV_HdmiRxSs_DdcGetRegDataHandler(void *RefPtr);
+static void XV_HdmiRxSs_DdcHdcpCallback(void *RefPtr, int Type);
+static void XV_HdmiRxSs_DdcHdcp14ProtocolEvtCallback(void *RefPtr);
+static void XV_HdmiRxSs_DdcHdcp22ProtocolEvtCallback(void *RefPtr);
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+static u32 XV_HdmiRxSs_DdcGetWriteMessageBufferWordsHandler(void *RefPtr);
+static u32 XV_HdmiRxSs_DdcGetReadMessageBufferWordsHandler(void *RefPtr);
+static u32 XV_HdmiRxSs_DdcIsReadMessageBufferEmptyHandler(void *RefPtr);
+static u32 XV_HdmiRxSs_DdcIsWriteMessageBufferEmptyHandler(void *RefPtr);
+static void XV_HdmiRxSs_DdcClearReadMessageBufferHandler(void *RefPtr);
+static void XV_HdmiRxSs_DdcClearWriteMessageBufferHandler(void *RefPtr);
+static void XV_HdmiRxSs_LinkErrorCallback(void *RefPtr);
+#endif
+
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiRxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiRxSs_SubcoreInitHdmiRx(XV_HdmiRxSs *HdmiRxSsPtr)
+{
+  int Status;
+  XV_HdmiRx_Config *ConfigPtr;
+
+  if(HdmiRxSsPtr->HdmiRxPtr)
+  {
+    /* Get core configuration */
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_HDMIRX_INIT, 0);
+#endif
+    ConfigPtr  = XV_HdmiRx_LookupConfig(HdmiRxSsPtr->Config.HdmiRx.DeviceId);
+    if(ConfigPtr == NULL)
+    {
+      xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: HDMI RX device not found\r\n");
+      return(XST_FAILURE);
+    }
+
+    /* Initialize core */
+    Status = XV_HdmiRx_CfgInitialize(HdmiRxSsPtr->HdmiRxPtr,
+                                    ConfigPtr,
+                                    HdmiRxSsPtr->Config.HdmiRx.AbsAddr);
+
+    if (Status != XST_SUCCESS)
+    {
+      xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: HDMI RX Initialization failed\r\n");
+      return(XST_FAILURE);
+    }
+
+    // Load EDID
+    XV_HdmiRx_DdcLoadEdid(HdmiRxSsPtr->HdmiRxPtr, HdmiRxSsPtr->EdidPtr,
+        HdmiRxSsPtr->EdidLength);
+
+  }
+  return(XST_SUCCESS);
+}
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiRxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiRxSs_SubcoreInitHdcpTimer(XV_HdmiRxSs *HdmiRxSsPtr)
+{
+  int Status;
+  XTmrCtr_Config *ConfigPtr;
+
+  if(HdmiRxSsPtr->HdcpTimerPtr)
+  {
+    /* Get core configuration */
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_HDCPTIMER_INIT, 0);
+#endif
+    ConfigPtr  = XTmrCtr_LookupConfig(HdmiRxSsPtr->Config.HdcpTimer.DeviceId);
+    if(ConfigPtr == NULL)
+    {
+      xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: AXIS Timer device not found\r\n");
+      return(XST_FAILURE);
+    }
+
+    /* Setup the instance */
+    memset(HdmiRxSsPtr->HdcpTimerPtr, 0, sizeof(XTmrCtr));
+
+    /* Initialize core */
+    XTmrCtr_CfgInitialize(HdmiRxSsPtr->HdcpTimerPtr,
+                          ConfigPtr,
+                          HdmiRxSsPtr->Config.HdcpTimer.AbsAddr);
+
+
+    Status = XTmrCtr_InitHw(HdmiRxSsPtr->HdcpTimerPtr);
+
+    /* Set Timer Counter instance in HDCP to the generic Hdcp1xRef
+       that will be used in callbacks */
+    HdmiRxSsPtr->Hdcp14Ptr->Hdcp1xRef = (void *)HdmiRxSsPtr->HdcpTimerPtr;
+
+    /* Initialize the hdcp timer functions */
+    XHdcp1x_SetTimerStart(HdmiRxSsPtr->Hdcp14Ptr,
+      &XV_HdmiRxSs_HdcpTimerStart);
+    XHdcp1x_SetTimerStop(HdmiRxSsPtr->Hdcp14Ptr,
+      &XV_HdmiRxSs_HdcpTimerStop);
+    XHdcp1x_SetTimerDelay(HdmiRxSsPtr->Hdcp14Ptr,
+      &XV_HdmiRxSs_HdcpTimerBusyDelay);
+
+    if(Status != XST_SUCCESS)
+    {
+      xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: AXI Timer Initialization failed\r\n");
+      return(XST_FAILURE);
+    }
+  }
+  return(XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiRxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiRxSs_SubcoreInitHdcp14(XV_HdmiRxSs *HdmiRxSsPtr)
+{
+  int Status;
+  XHdcp1x_Config *ConfigPtr;
+
+  /* Is the HDCP 1.4 RX present? */
+  if (HdmiRxSsPtr->Hdcp14Ptr) {
+
+    /* Is the key loaded? */
+    if (HdmiRxSsPtr->Hdcp14KeyPtr) {
+
+      /* Get core configuration */
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+      XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_HDCP14_INIT, 0);
+#endif
+      ConfigPtr  = XHdcp1x_LookupConfig(HdmiRxSsPtr->Config.Hdcp14.DeviceId);
+      if(ConfigPtr == NULL)
+      {
+        xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: HDCP 1.4 device not found\r\n");
+        return(XST_FAILURE);
+      }
+
+      /* Initialize core */
+      void *PhyIfPtr = HdmiRxSsPtr->HdmiRxPtr;
+      Status = XHdcp1x_CfgInitialize(HdmiRxSsPtr->Hdcp14Ptr,
+                                        ConfigPtr,
+                                        PhyIfPtr,
+                                        HdmiRxSsPtr->Config.Hdcp14.AbsAddr);
+
+      /* Self-test the hdcp interface */
+      if (XHdcp1x_SelfTest(HdmiRxSsPtr->Hdcp14Ptr) != XST_SUCCESS) {
+          Status = XST_FAILURE;
+      }
+
+      if(Status != XST_SUCCESS)
+      {
+        xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: HDCP 1.4 Initialization failed\r\n");
+        return(XST_FAILURE);
+      }
+
+      /* Set-up the DDC Handlers */
+      XHdcp1x_SetCallback(HdmiRxSsPtr->Hdcp14Ptr,
+                          XHDCP1X_HANDLER_DDC_SETREGADDR,
+						  (void *)(XHdcp1x_SetDdcHandler)XV_HdmiRxSs_DdcSetRegAddrHandler,
+						  (void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp1x_SetCallback(HdmiRxSsPtr->Hdcp14Ptr,
+                          XHDCP1X_HANDLER_DDC_SETREGDATA,
+						  (void *)(XHdcp1x_SetDdcHandler)XV_HdmiRxSs_DdcSetRegDataHandler,
+						  (void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp1x_SetCallback(HdmiRxSsPtr->Hdcp14Ptr,
+                          XHDCP1X_HANDLER_DDC_GETREGDATA,
+						  (void *)(XHdcp1x_GetDdcHandler)XV_HdmiRxSs_DdcGetRegDataHandler,
+						  (void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      /* Select key */
+      XHdcp1x_SetKeySelect(HdmiRxSsPtr->Hdcp14Ptr, XV_HDMIRXSS_HDCP_KEYSEL);
+
+      /* Disable HDCP 1.4 repeater */
+      HdmiRxSsPtr->Hdcp14Ptr->IsRepeater = 0;
+
+      /* Set-up the HDMI RX HDCP Callback Handler */
+      XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                XV_HDMIRX_HANDLER_HDCP,
+				(void *)XV_HdmiRxSs_DdcHdcpCallback,
+                (void *)HdmiRxSsPtr);
+
+      /* Set-up the HDMI RX HDCP 1.4 Protocol Event Callback Handler */
+	  XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+			    XV_HDMIRX_HANDLER_DDC_HDCP_14_PROT,
+				(void *)XV_HdmiRxSs_DdcHdcp14ProtocolEvtCallback,
+				(void *)HdmiRxSsPtr);
+
+      /* Enable HDMI-RX DDC interrupts */
+      XV_HdmiRx_DdcIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+
+      /* Enable HDMI-RX HDCP */
+      XV_HdmiRx_DdcHdcpEnable(HdmiRxSsPtr->HdmiRxPtr);
+
+      /* Clear the HDCP KSV Fifo */
+      XV_HdmiRx_DdcHdcpClearReadMessageBuffer(HdmiRxSsPtr->HdmiRxPtr);
+
+      /* Clear the event queue */
+      XV_HdmiRxSs_HdcpClearEvents(HdmiRxSsPtr);
+
+      XHdcp1x_LateInit(HdmiRxSsPtr->Hdcp14Ptr);
+    }
+  }
+  return(XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiRxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiRxSs_SubcoreInitHdcp22(XV_HdmiRxSs *HdmiRxSsPtr)
+{
+  int Status;
+  XHdcp22_Rx_Config *ConfigPtr;
+
+  /* Is the HDCP 2.2 RX present? */
+  if (HdmiRxSsPtr->Hdcp22Ptr) {
+
+    /* Are the keys loaded? */
+    if (HdmiRxSsPtr->Hdcp22Lc128Ptr && HdmiRxSsPtr->Hdcp22PrivateKeyPtr) {
+
+      /* Get core configuration */
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+      XV_HdmiRxSs_LogWrite(HdmiRxSsPtr, XV_HDMIRXSS_LOG_EVT_HDCP22_INIT, 0);
+#endif
+      ConfigPtr  = XHdcp22Rx_LookupConfig(HdmiRxSsPtr->Config.Hdcp22.DeviceId);
+      if(ConfigPtr == NULL)
+      {
+        xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: HDCP 2.2 device not found\r\n");
+        return (XST_FAILURE);
+      }
+
+      /* Initialize core */
+      Status = XHdcp22Rx_CfgInitialize(HdmiRxSsPtr->Hdcp22Ptr,
+                                       ConfigPtr,
+                                       HdmiRxSsPtr->Config.Hdcp22.AbsAddr);
+      if (Status != XST_SUCCESS)
+      {
+        xdbg_printf(XDBG_DEBUG_GENERAL,"HDMIRXSS ERR:: HDCP 2.2 Initialization failed\r\n");
+        return(XST_FAILURE);
+      }
+
+      /* Set-up the DDC Handlers */
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_SETREGADDR,
+							(void *)(XHdcp22_Rx_SetHandler)XV_HdmiRxSs_DdcSetRegAddrHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_SETREGDATA,
+							(void *)(XHdcp22_Rx_SetHandler)XV_HdmiRxSs_DdcSetRegDataHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_GETREGDATA,
+							(void *)(XHdcp22_Rx_GetHandler)XV_HdmiRxSs_DdcGetRegDataHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_GETWBUFSIZE,
+							(void *)(XHdcp22_Rx_GetHandler)XV_HdmiRxSs_DdcGetWriteMessageBufferWordsHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_GETRBUFSIZE,
+							(void *)(XHdcp22_Rx_GetHandler)XV_HdmiRxSs_DdcGetReadMessageBufferWordsHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_ISWBUFEMPTY,
+							(void *)(XHdcp22_Rx_GetHandler)XV_HdmiRxSs_DdcIsWriteMessageBufferEmptyHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_ISRBUFEMPTY,
+							(void *)(XHdcp22_Rx_GetHandler)XV_HdmiRxSs_DdcIsReadMessageBufferEmptyHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_CLEARRBUF,
+							(void *)(XHdcp22_Rx_RunHandler)XV_HdmiRxSs_DdcClearReadMessageBufferHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+      XHdcp22Rx_SetCallback(HdmiRxSsPtr->Hdcp22Ptr,
+                            XHDCP22_RX_HANDLER_DDC_CLEARWBUF,
+							(void *)(XHdcp22_Rx_RunHandler)XV_HdmiRxSs_DdcClearWriteMessageBufferHandler,
+							(void *)HdmiRxSsPtr->HdmiRxPtr);
+
+
+      /* Set-up the HDMI RX HDCP Callback Handler */
+      XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                XV_HDMIRX_HANDLER_HDCP,
+				(void *)XV_HdmiRxSs_DdcHdcpCallback,
+                (void *)HdmiRxSsPtr);
+
+      /* Set-up the HDMI RX HDCP 2.2 Protocol Event Callback Handler */
+	  XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+				XV_HDMIRX_HANDLER_DDC_HDCP_22_PROT,
+				(void *)XV_HdmiRxSs_DdcHdcp22ProtocolEvtCallback,
+				(void *)HdmiRxSsPtr);
+
+      /* Set-up the HDMI RX Link error Callback Handler */
+      XV_HdmiRx_SetCallback(HdmiRxSsPtr->HdmiRxPtr,
+                XV_HDMIRX_HANDLER_LINK_ERROR,
+				(void *)XV_HdmiRxSs_LinkErrorCallback,
+                (void *)HdmiRxSsPtr);
+
+      /* Load Production Keys */
+      XHdcp22Rx_LoadLc128(HdmiRxSsPtr->Hdcp22Ptr, HdmiRxSsPtr->Hdcp22Lc128Ptr);
+      XHdcp22Rx_LoadPublicCert(HdmiRxSsPtr->Hdcp22Ptr, HdmiRxSsPtr->Hdcp22PrivateKeyPtr+40);
+      XHdcp22Rx_LoadPrivateKey(HdmiRxSsPtr->Hdcp22Ptr, HdmiRxSsPtr->Hdcp22PrivateKeyPtr+562);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+      XHdcp22Rx_LogReset(HdmiRxSsPtr->Hdcp22Ptr, FALSE);
+#endif
+      /* Enable HDMI-RX DDC interrupts */
+      XV_HdmiRx_DdcIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+
+      /* Enable HDMI-RX HDCP */
+      XV_HdmiRx_DdcHdcpEnable(HdmiRxSsPtr->HdmiRxPtr);
+
+      /* Clear the event queue */
+      XV_HdmiRxSs_HdcpClearEvents(HdmiRxSsPtr);
+
+      /* Default enable broadcasting */
+      XHdcp22Rx_SetBroadcast(HdmiRxSsPtr->Hdcp22Ptr, TRUE);
+    }
+  }
+
+  return (XST_SUCCESS);
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC set register address handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @param Data is the address to be written.
+ *
+ * @return None.
+ *
+ ******************************************************************************/
+static void XV_HdmiRxSs_DdcSetRegAddrHandler(void *RefPtr, u32 Data)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  XV_HdmiRx_DdcHdcpSetAddress(InstancePtr, Data);
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC set register data handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @param Data is the data to be written.
+ *
+ * @return None.
+ *
+ ******************************************************************************/
+static void XV_HdmiRxSs_DdcSetRegDataHandler(void *RefPtr, u32 Data)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  XV_HdmiRx_DdcHdcpWriteData(InstancePtr, Data);
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC get register data handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return The read data.
+ *
+ ******************************************************************************/
+static u32 XV_HdmiRxSs_DdcGetRegDataHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  return XV_HdmiRx_DdcHdcpReadData(InstancePtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC get write message buffer words handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return The number of words in the Write Message Buffer.
+ *
+ ******************************************************************************/
+static u32 XV_HdmiRxSs_DdcGetWriteMessageBufferWordsHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  return XV_HdmiRx_DdcGetHdcpWriteMessageBufferWords(InstancePtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC get read message buffer words handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return The number of words in the Read Message Buffer.
+ *
+ ******************************************************************************/
+static u32 XV_HdmiRxSs_DdcGetReadMessageBufferWordsHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  return XV_HdmiRx_DdcGetHdcpReadMessageBufferWords(InstancePtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC get read message buffer is empty handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return
+ *  - TRUE if read message buffer is empty.
+ *  - FALSE if read message buffer is not empty.
+ *
+ ******************************************************************************/
+static u32 XV_HdmiRxSs_DdcIsReadMessageBufferEmptyHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  return XV_HdmiRx_DdcIsHdcpReadMessageBufferEmpty(InstancePtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC get write message buffer is empty handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return
+ *  - TRUE if write message buffer is empty.
+ *  - FALSE if write message buffer is not empty.
+ *
+ ******************************************************************************/
+static u32 XV_HdmiRxSs_DdcIsWriteMessageBufferEmptyHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  return XV_HdmiRx_DdcIsHdcpWriteMessageBufferEmpty(InstancePtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC clear read message buffer handler for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return None
+ *
+ ******************************************************************************/
+static void XV_HdmiRxSs_DdcClearReadMessageBufferHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  XV_HdmiRx_DdcHdcpClearReadMessageBuffer(InstancePtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC clear write message buffer for the RX.
+ *
+ * @param RefPtr is a callback reference to the HDMI RX instance.
+ *
+ * @return None
+ *
+ ******************************************************************************/
+static void XV_HdmiRxSs_DdcClearWriteMessageBufferHandler(void *RefPtr)
+{
+  XV_HdmiRx *InstancePtr = (XV_HdmiRx *)RefPtr;
+  XV_HdmiRx_DdcHdcpClearWriteMessageBuffer(InstancePtr);
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+* This function is called when the HDMI-RX DDC HDCP interrupt has occurred.
+*
+* @param RefPtr is a callback reference to the HDCP22 RX instance.
+* @param Type indicates the cause of the interrupt.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+static void XV_HdmiRxSs_DdcHdcpCallback(void *RefPtr, int Type)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr;
+  HdmiRxSsPtr = (XV_HdmiRxSs*) RefPtr;
+
+  switch (Type)
+  {
+    // HDCP 2.2. write message event
+    case XV_HDMIRX_DDC_STA_HDCP_WMSG_NEW_EVT_MASK:
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+      if (HdmiRxSsPtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetWriteMessageAvailable(HdmiRxSsPtr->Hdcp22Ptr);
+      }
+#endif
+      break;
+
+    // HDCP 2.2 read message event
+    case XV_HDMIRX_DDC_STA_HDCP_RMSG_END_EVT_MASK:
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+      if (HdmiRxSsPtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetReadMessageComplete(HdmiRxSsPtr->Hdcp22Ptr);
+      }
+#endif
+      break;
+
+    // HDCP 2.2 read not complete event
+    case XV_HDMIRX_DDC_STA_HDCP_RMSG_NC_EVT_MASK:
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+      if (HdmiRxSsPtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetDdcError(HdmiRxSsPtr->Hdcp22Ptr);
+      }
+#endif
+      break;
+
+    // HDCP 1.4 Aksv event
+    case XV_HDMIRX_DDC_STA_HDCP_AKSV_EVT_MASK:
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (HdmiRxSsPtr->Hdcp14Ptr) {
+        XHdcp1x_ProcessAKsv(HdmiRxSsPtr->Hdcp14Ptr);
+      }
+#endif
+      break;
+
+    // HDCP 1.4 protocol event
+    case XV_HDMIRX_DDC_STA_HDCP_1_PROT_EVT_MASK:
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+      if (HdmiRxSsPtr->Hdcp14Ptr && HdmiRxSsPtr->Hdcp22Ptr) {
+#ifdef USE_HDCP_14_PROT_EVT_ENUM
+        XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_1_PROT_EVT);
+#endif
+      }
+#endif
+      break;
+
+    // HDCP 2.2 protocol event
+    case XV_HDMIRX_DDC_STA_HDCP_2_PROT_EVT_MASK:
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+      if (HdmiRxSsPtr->Hdcp14Ptr && HdmiRxSsPtr->Hdcp22Ptr) {
+#ifdef USE_HDCP_22_PROT_EVT_ENUM
+        XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_2_PROT_EVT);
+#endif
+      }
+#endif
+      break;
+
+    default:
+      break;
+  }
+}
+
+/*****************************************************************************/
+/**
+* This function is called when the HDMI-RX DDC HDCP 1.4 Protocol Event
+* interrupt has occurred.
+*
+* @param RefPtr is a callback reference to the HDCP22 RX instance.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+static void XV_HdmiRxSs_DdcHdcp14ProtocolEvtCallback(void *RefPtr)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr;
+  HdmiRxSsPtr = (XV_HdmiRxSs*) RefPtr;
+
+  /* Enable HDCP 1.4 */
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+  if (HdmiRxSsPtr->Hdcp14Ptr && HdmiRxSsPtr->Hdcp22Ptr) {
+	if (XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_14) !=
+	    XST_SUCCESS) {
+	  XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_22);
+	}
+  }
+#endif
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+* This function is called when the HDMI-RX link error has occurred.
+*
+* @param RefPtr is a callback reference to the HDCP22 RX instance.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+static void XV_HdmiRxSs_LinkErrorCallback(void *RefPtr)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr;
+  HdmiRxSsPtr = (XV_HdmiRxSs*) RefPtr;
+
+  // HDCP 2.2
+  if (HdmiRxSsPtr->Hdcp22Ptr) {
+    if (HdmiRxSsPtr->HdcpProtocol == XV_HDMIRXSS_HDCP_22) {
+      XHdcp22Rx_SetLinkError(HdmiRxSsPtr->Hdcp22Ptr);
+    }
+  }
+}
+
+/*****************************************************************************/
+/**
+* This function is called when the HDMI-RX DDC HDCP 2.2 Protocol Event
+* interrupt has occurred.
+*
+* @param RefPtr is a callback reference to the HDCP22 RX instance.
+*
+* @return None.
+*
+* @note   None.
+******************************************************************************/
+static void XV_HdmiRxSs_DdcHdcp22ProtocolEvtCallback(void *RefPtr)
+{
+  XV_HdmiRxSs *HdmiRxSsPtr;
+  HdmiRxSsPtr = (XV_HdmiRxSs*) RefPtr;
+
+  /* Enable HDCP 2.2 */
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+  if (HdmiRxSsPtr->Hdcp14Ptr && HdmiRxSsPtr->Hdcp22Ptr) {
+	if (XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_22) !=
+		XST_SUCCESS) {
+	  XV_HdmiRxSs_HdcpSetProtocol(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_14);
+	}
+  }
+#endif
+}
+#endif
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_coreinit.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_coreinit.h
@@ -0,0 +1,66 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirxss_coreinit.h
+* @{
+* @details
+*
+* This header file contains the hdmi rx subsystem sub-cores
+* initialization routines and helper functions.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     20/01/16 Added remapper support
+* 1.2   MG     03/02/16 Added HDCP support
+* 1.3   MH     08/08/16 Updates to optimize out HDCP when excluded.
+* 1.4   YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.5   MMO    03/01/16 Remove repetitive inclusion of header files
+* </pre>
+*
+******************************************************************************/
+#ifndef XV_HDMIRXSS_COREINIT_H__  /* prevent circular inclusions */
+#define XV_HDMIRXSS_COREINIT_H__  /* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "xv_hdmirxss.h"
+/************************** Constant Definitions *****************************/
+
+/************************** Function Prototypes ******************************/
+int XV_HdmiRxSs_SubcoreInitHdmiRx(XV_HdmiRxSs *HdmiRxSsPtr);
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+int XV_HdmiRxSs_SubcoreInitHdcpTimer(XV_HdmiRxSs *HdmiRxSsPtr);
+int XV_HdmiRxSs_SubcoreInitHdcp14(XV_HdmiRxSs *HdmiRxSsPtr);
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+int XV_HdmiRxSs_SubcoreInitHdcp22(XV_HdmiRxSs *HdmiRxSsPtr);
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_hdcp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_hdcp.c
@@ -0,0 +1,2176 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmirxss_hdcp.c
+*
+* This is main code of Xilinx HDMI Receiver Subsystem for HDCP Functionality.
+* Please see xv_hdmirxss.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00   MMO 19/12/16 Move HDCP Code from xv_hdmirxss.c to xv_hdmirxss_hdcp.c
+* 3.2    MH  04/07/17 Fixed issue to prevent HDCP protocol switching when only
+*                     one protocol is in the design.
+*        MH  09/08/17 Added function XV_HdmiRxSs_HdcpSetCapability
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include <linux/version.h>
+#include "xv_hdmirxss.h"
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+// HDCP specific
+#ifdef USE_HDCP_RX
+static XV_HdmiRxSs_HdcpEvent XV_HdmiRxSs_HdcpGetEvent(XV_HdmiRxSs *InstancePtr);
+static int XV_HdmiRxSs_HdcpProcessEvents(XV_HdmiRxSs *InstancePtr);
+static int XV_HdmiRxSs_HdcpReset(XV_HdmiRxSs *InstancePtr);
+static int XV_HdmiRxSs_HdcpSetTopologyDepth(XV_HdmiRxSs *InstancePtr, u32 Depth);
+static int XV_HdmiRxSs_HdcpSetTopologyDeviceCnt(XV_HdmiRxSs *InstancePtr, u32 DeviceCnt);
+static int XV_HdmiRxSs_HdcpSetTopologyMaxDevsExceeded(XV_HdmiRxSs *InstancePtr, u8 Value);
+static int XV_HdmiRxSs_HdcpSetTopologyMaxCascadeExceeded(XV_HdmiRxSs *InstancePtr, u8 Value);
+static int XV_HdmiRxSs_HdcpSetTopologyHdcp2LegacyDeviceDownstream(XV_HdmiRxSs *InstancePtr, u8 Value);
+static int XV_HdmiRxSs_HdcpSetTopologyHdcp1DeviceDownstream(XV_HdmiRxSs *InstancePtr, u8 Value);
+#endif
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+static u32 XV_HdmiRxSs_HdcpTimerConvUsToTicks(u32 TimeoutInUs,
+                                            u32 ClockFrequency);
+static void XV_HdmiRxSs_HdcpTimerCallback(void *CallBackRef, u8 TimerChannel);
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/************************** Function Definition ******************************/
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDCP
+ *
+ * @param  InstancePtr is a pointer to the HDMI RX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiRxSS_HdcpIntrHandler(XV_HdmiRxSs *InstancePtr)
+{
+  XHdcp1x_CipherIntrHandler(InstancePtr->Hdcp14Ptr);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDCP Timer
+ *
+ * @param  InstancePtr is a pointer to the HDMI RX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiRxSS_HdcpTimerIntrHandler(XV_HdmiRxSs *InstancePtr)
+{
+  XTmrCtr_InterruptHandler(InstancePtr->HdcpTimerPtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDCP 2.2 Timer
+ *
+ * @param  InstancePtr is a pointer to the HDMI RX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiRxSS_Hdcp22TimerIntrHandler(XV_HdmiRxSs *InstancePtr)
+{
+  XTmrCtr *XTmrCtrPtr;
+
+  XTmrCtrPtr = XHdcp22Rx_GetTimer(InstancePtr->Hdcp22Ptr);
+
+  XTmrCtr_InterruptHandler(XTmrCtrPtr);
+}
+#endif
+
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function converts from microseconds to timer ticks
+*
+* @param TimeoutInUs  the timeout to convert
+* @param ClockFrequency  the clock frequency to use in the conversion
+*
+* @return
+*   The number of "ticks"
+*
+* @note
+*   None.
+*
+******************************************************************************/
+static u32 XV_HdmiRxSs_HdcpTimerConvUsToTicks(u32 TimeoutInUs,
+                                                    u32 ClockFrequency)
+{
+  u32 TimeoutFreq = 0;
+  u32 NumTicks = 0;
+
+  /* Check for greater than one second */
+  if (TimeoutInUs > 1000000ul) {
+      u32 NumSeconds = 0;
+
+      /* Determine theNumSeconds */
+      NumSeconds = (TimeoutInUs/1000000ul);
+
+      /* Update theNumTicks */
+      NumTicks = (NumSeconds*ClockFrequency);
+
+      /* Adjust theTimeoutInUs */
+      TimeoutInUs -= (NumSeconds*1000000ul);
+  }
+
+  /* Convert TimeoutFreq to a frequency */
+  TimeoutFreq  = 1000;
+  TimeoutFreq *= 1000;
+  TimeoutFreq /= TimeoutInUs;
+
+  /* Update NumTicks */
+  NumTicks += ((ClockFrequency / TimeoutFreq) + 1);
+
+  return (NumTicks);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+*
+* This function serves as the timer callback function
+*
+* @param CallBackRef  the callback reference value
+* @param TimerChannel  the channel within the timer that expired
+*
+* @return
+*   void
+*
+* @note
+*   None
+*
+******************************************************************************/
+static void XV_HdmiRxSs_HdcpTimerCallback(void* CallBackRef, u8 TimerChannel)
+{
+  XHdcp1x* HdcpPtr = (XHdcp1x*) CallBackRef;
+
+  TimerChannel = TimerChannel;
+  XHdcp1x_HandleTimeout(HdcpPtr);
+  return;
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function starts a timer on behalf of an hdcp interface
+*
+* @param InstancePtr  the hdcp interface
+* @param TimeoutInMs  the timer duration in milliseconds
+*
+* @return
+*   XST_SUCCESS if successful
+*
+* @note
+*   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpTimerStart(void *InstancePtr, u16 TimeoutInMs)
+{
+  XHdcp1x *HdcpPtr = (XHdcp1x *)InstancePtr;
+  XTmrCtr *TimerPtr = (XTmrCtr *)HdcpPtr->Hdcp1xRef;
+
+  u8 TimerChannel = 0;
+  u32 TimerOptions = 0;
+  u32 NumTicks = 0;
+
+  /* Verify argument. */
+  Xil_AssertNonvoid(TimerPtr != NULL);
+
+  /* Determine NumTicks */
+  NumTicks = XV_HdmiRxSs_HdcpTimerConvUsToTicks((TimeoutInMs*1000ul),
+        TimerPtr->Config.SysClockFreqHz);
+
+  /* Stop it */
+  XTmrCtr_Stop(TimerPtr, TimerChannel);
+
+  /* Configure the callback */
+  XTmrCtr_SetHandler(TimerPtr, &XV_HdmiRxSs_HdcpTimerCallback,
+                                              (void*) InstancePtr);
+
+  /* Configure the timer options */
+  TimerOptions  = XTmrCtr_GetOptions(TimerPtr, TimerChannel);
+  TimerOptions |=  XTC_DOWN_COUNT_OPTION;
+  TimerOptions |=  XTC_INT_MODE_OPTION;
+  TimerOptions &= ~XTC_AUTO_RELOAD_OPTION;
+  XTmrCtr_SetOptions(TimerPtr, TimerChannel, TimerOptions);
+
+  /* Set the timeout and start */
+  XTmrCtr_SetResetValue(TimerPtr, TimerChannel, NumTicks);
+  XTmrCtr_Start(TimerPtr, TimerChannel);
+
+  return (XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function stops a timer on behalf of an hdcp interface
+*
+* @param InstancePtr  the hdcp interface
+*
+* @return
+*   XST_SUCCESS if successful
+*
+* @note
+*   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpTimerStop(void *InstancePtr)
+{
+  XHdcp1x *HdcpPtr = (XHdcp1x *)InstancePtr;
+  XTmrCtr *TimerPtr = (XTmrCtr *)HdcpPtr->Hdcp1xRef;
+
+  u8 TimerChannel = 0;
+
+  /* Verify argument. */
+  Xil_AssertNonvoid(TimerPtr != NULL);
+
+  /* Stop it */
+  XTmrCtr_Stop(TimerPtr, TimerChannel);
+
+  return (XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function busy waits for an interval on behalf of an hdcp interface
+*
+* @param InstancePtr  the hdcp interface
+* @param DelayInMs  the delay duration in milliseconds
+*
+* @return
+*   XST_SUCCESS if successful
+*
+* @note
+*   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpTimerBusyDelay(void *InstancePtr, u16 DelayInMs)
+{
+
+  XHdcp1x *HdcpPtr = (XHdcp1x *)InstancePtr;
+  XTmrCtr *TimerPtr = (XTmrCtr *)HdcpPtr->Hdcp1xRef;
+
+  u8 TimerChannel = 0;
+  u32 TimerOptions = 0;
+  u32 NumTicks = 0;
+
+  /* Verify argument. */
+	Xil_AssertNonvoid(TimerPtr != NULL);
+
+  /* Determine NumTicks */
+  NumTicks = XV_HdmiRxSs_HdcpTimerConvUsToTicks((DelayInMs*1000ul),
+                TimerPtr->Config.SysClockFreqHz);
+
+  /* Stop it */
+  XTmrCtr_Stop(TimerPtr, TimerChannel);
+
+  /* Configure the timer options */
+  TimerOptions  = XTmrCtr_GetOptions(TimerPtr, TimerChannel);
+  TimerOptions |=  XTC_DOWN_COUNT_OPTION;
+  TimerOptions &= ~XTC_INT_MODE_OPTION;
+  TimerOptions &= ~XTC_AUTO_RELOAD_OPTION;
+  XTmrCtr_SetOptions(TimerPtr, TimerChannel, TimerOptions);
+
+  /* Set the timeout and start */
+  XTmrCtr_SetResetValue(TimerPtr, TimerChannel, NumTicks);
+  XTmrCtr_Start(TimerPtr, TimerChannel);
+
+  /* Wait until done */
+  while (!XTmrCtr_IsExpired(TimerPtr, TimerChannel));
+
+  return (XST_SUCCESS);
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function pushes an event into the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Event is the event to be pushed in the queue.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpPushEvent(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpEvent Event)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(Event < XV_HDMIRXSS_HDCP_INVALID_EVT);
+
+  /* Write event into the queue */
+  InstancePtr->HdcpEventQueue.Queue[InstancePtr->HdcpEventQueue.Head] = Event;
+
+  /* Update head pointer */
+  if (InstancePtr->HdcpEventQueue.Head == (XV_HDMIRXSS_HDCP_MAX_QUEUE_SIZE - 1)) {
+    InstancePtr->HdcpEventQueue.Head = 0;
+  }
+  else {
+    InstancePtr->HdcpEventQueue.Head++;
+  }
+
+  /* Check tail pointer. When the two pointer are equal, then the buffer
+   * is full. In this case then increment the tail pointer as well to
+   * remove the oldest entry from the buffer.
+   */
+  if (InstancePtr->HdcpEventQueue.Tail == InstancePtr->HdcpEventQueue.Head) {
+    if (InstancePtr->HdcpEventQueue.Tail == (XV_HDMIRXSS_HDCP_MAX_QUEUE_SIZE - 1)) {
+      InstancePtr->HdcpEventQueue.Tail = 0;
+    }
+    else {
+      InstancePtr->HdcpEventQueue.Tail++;
+    }
+  }
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function gets an event from the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return When the queue is filled, the next event is returned.
+*         When the queue is empty, XV_HDMIRXSS_HDCP_NO_EVT is returned.
+*
+* @note   None.
+*
+******************************************************************************/
+static XV_HdmiRxSs_HdcpEvent XV_HdmiRxSs_HdcpGetEvent(XV_HdmiRxSs *InstancePtr)
+{
+  XV_HdmiRxSs_HdcpEvent Event;
+
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  /* Check if there are any events in the queue */
+  if (InstancePtr->HdcpEventQueue.Tail == InstancePtr->HdcpEventQueue.Head) {
+    return XV_HDMIRXSS_HDCP_NO_EVT;
+  }
+
+  Event = InstancePtr->HdcpEventQueue.Queue[InstancePtr->HdcpEventQueue.Tail];
+
+  /* Update tail pointer */
+  if (InstancePtr->HdcpEventQueue.Tail == (XV_HDMIRXSS_HDCP_MAX_QUEUE_SIZE - 1)) {
+    InstancePtr->HdcpEventQueue.Tail = 0;
+  }
+  else {
+    InstancePtr->HdcpEventQueue.Tail++;
+  }
+
+  return Event;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function clears all pending events from the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpClearEvents(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  InstancePtr->HdcpEventQueue.Head = 0;
+  InstancePtr->HdcpEventQueue.Tail = 0;
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function processes pending events from the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpProcessEvents(XV_HdmiRxSs *InstancePtr)
+{
+  XV_HdmiRxSs_HdcpEvent Event;
+  int Status = XST_SUCCESS;
+
+  /* Verify argument */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  Event = XV_HdmiRxSs_HdcpGetEvent(InstancePtr);
+
+  switch (Event) {
+
+    // Stream up
+    case XV_HDMIRXSS_HDCP_STREAMUP_EVT :
+      break;
+
+    // Stream down
+    case XV_HDMIRXSS_HDCP_STREAMDOWN_EVT :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, FALSE);
+      }
+#endif
+      break;
+
+    // Connect
+    case XV_HDMIRXSS_HDCP_CONNECT_EVT :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        // Set physical state
+        XHdcp1x_SetPhysicalState(InstancePtr->Hdcp14Ptr, TRUE);
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+      }
+#endif
+      XV_HdmiRxSs_HdcpSetProtocol(InstancePtr, InstancePtr->HdcpProtocol);
+      break;
+
+    // Disconnect
+    // Enable the previous HDCP protocol
+    case XV_HDMIRXSS_HDCP_DISCONNECT_EVT :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        // Clear HDMI mode
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, FALSE);
+
+        // Set physical state
+        XHdcp1x_SetPhysicalState(InstancePtr->Hdcp14Ptr, FALSE);
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+      }
+#endif
+      break;
+
+#ifdef USE_HDCP_14_PROT_EVT_ENUM
+    // HDCP 1.4 protocol event
+    // Enable HDCP 1.4
+    case XV_HDMIRXSS_HDCP_1_PROT_EVT :
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+      if (InstancePtr->Hdcp14Ptr && InstancePtr->Hdcp22Ptr) {
+        if(XV_HdmiRxSs_HdcpSetProtocol(InstancePtr, XV_HDMIRXSS_HDCP_14) != XST_SUCCESS) {
+          XV_HdmiRxSs_HdcpSetProtocol(InstancePtr, XV_HDMIRXSS_HDCP_22);
+        }
+      }
+#endif
+      break;
+#endif
+
+#ifdef USE_HDCP_22_PROT_EVT_ENUM
+    // HDCP 2.2 protocol event
+    // Enable HDCP 2.2
+    case XV_HDMIRXSS_HDCP_2_PROT_EVT :
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_RX_NUM_INSTANCES)
+      if (InstancePtr->Hdcp14Ptr && InstancePtr->Hdcp22Ptr) {
+        if(XV_HdmiRxSs_HdcpSetProtocol(InstancePtr, XV_HDMIRXSS_HDCP_22) != XST_SUCCESS) {
+          XV_HdmiRxSs_HdcpSetProtocol(InstancePtr, XV_HDMIRXSS_HDCP_14);
+        }
+      }
+#endif
+      break;
+#endif
+
+    // DVI mode event
+    case XV_HDMIRXSS_HDCP_DVI_MODE_EVT:
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, FALSE);
+      }
+#endif
+      break;
+
+    // HDMI mode event
+    case XV_HDMIRXSS_HDCP_HDMI_MODE_EVT:
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, TRUE);
+      }
+#endif
+      break;
+
+    // Sync loss event
+    case XV_HDMIRXSS_HDCP_SYNC_LOSS_EVT:
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, FALSE);
+      }
+#endif
+      break;
+
+      // Sync est/recover event
+      case XV_HDMIRXSS_HDCP_SYNC_EST_EVT:
+  #ifdef XPAR_XHDCP_NUM_INSTANCES
+        if (InstancePtr->Hdcp14Ptr) {
+          XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, TRUE);
+        }
+  #endif
+        break;
+
+    default :
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function schedules the available HDCP cores. Only the active
+* HDCP protocol poll function is executed. HDCP 1.4 and 2.2 poll
+* functions should not execute in parallel.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpPoll(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  /* Only poll when the HDCP is ready */
+  if (InstancePtr->HdcpIsReady) {
+
+    /* Process any pending events from the RX event queue */
+    XV_HdmiRxSs_HdcpProcessEvents(InstancePtr);
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    if (InstancePtr->Hdcp22Ptr) {
+      if (XHdcp22Rx_IsEnabled(InstancePtr->Hdcp22Ptr)) {
+        XHdcp22Rx_Poll(InstancePtr->Hdcp22Ptr);
+      }
+    }
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    if (InstancePtr->Hdcp14Ptr) {
+      if (XHdcp1x_IsEnabled(InstancePtr->Hdcp14Ptr)) {
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+    }
+#endif
+  }
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the active HDCP protocol and enables it.
+* The protocol can be set to either HDCP 1.4, 2.2, or None.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Protocol is the requested content protection scheme of type
+*        XV_HdmiRxSs_HdcpProtocol.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetProtocol(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpProtocol Protocol)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid((Protocol == XV_HDMIRXSS_HDCP_NONE) ||
+                    (Protocol == XV_HDMIRXSS_HDCP_14)   ||
+                    (Protocol == XV_HDMIRXSS_HDCP_22));
+
+  int Status;
+
+  /* Set requested protocol */
+  if ((InstancePtr->UserHdcpProt != XV_HDMIRXSS_HDCP_NOUSERPREF) &&
+		  (Protocol != InstancePtr->UserHdcpProt))
+	  return XST_SUCCESS;
+
+  InstancePtr->HdcpProtocol = Protocol;
+
+  /* Reset both protocols */
+  Status = XV_HdmiRxSs_HdcpReset(InstancePtr);
+  if (Status != XST_SUCCESS) {
+    InstancePtr->HdcpProtocol = XV_HDMIRXSS_HDCP_NONE;
+    return XST_FAILURE;
+  }
+
+  /* Enable the requested protocol */
+  Status = XV_HdmiRxSs_HdcpEnable(InstancePtr);
+  if (Status != XST_SUCCESS) {
+    InstancePtr->HdcpProtocol = XV_HDMIRXSS_HDCP_NONE;
+    return XST_FAILURE;
+  }
+
+  return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the active HDCP protocol and enables it.
+* XV_HdmiRxSs_HdcpSetProtocol is intended to be used internally.
+* Applications should API XV_HdmiRxSs_SetUserHdcpProtocol
+* instead of directly using XV_HdmiRxSs_HdcpSetProtocol.
+*
+* The protocol can be set to either HDCP 1.4, 2.2, or None.
+* XV_HDMIRXSS_HDCP_NOUSERPREF is the default state and should
+* be reset back to this state when application wants the HDCP
+* configuration based on source connected.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Protocol is the requested content protection scheme of type
+*        XV_HdmiRxSs_HdcpProtocol.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+
+int XV_HdmiRxSs_SetUserHdcpProtocol(XV_HdmiRxSs *InstancePtr,
+		XV_HdmiRxSs_HdcpProtocol protocol)
+{
+	int Status = XST_SUCCESS;
+
+	Xil_AssertNonvoid((protocol == XV_HDMIRXSS_HDCP_NONE) ||
+		(protocol == XV_HDMIRXSS_HDCP_NOUSERPREF) ||
+		(protocol == XV_HDMIRXSS_HDCP_14) ||
+		(protocol == XV_HDMIRXSS_HDCP_22));
+
+	XV_HdmiRx_DdcHdcpDisable(InstancePtr->HdmiRxPtr);
+
+	InstancePtr->UserHdcpProt = protocol;
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+	if (protocol == XV_HDMIRXSS_HDCP_14)
+		XHdcp22Rx_SetBroadcast(InstancePtr->Hdcp22Ptr, FALSE);
+	else
+		XHdcp22Rx_SetBroadcast(InstancePtr->Hdcp22Ptr, TRUE);
+#endif
+
+	if (protocol != XV_HDMIRXSS_HDCP_NOUSERPREF)
+		Status =  XV_HdmiRxSs_HdcpSetProtocol(InstancePtr, protocol);
+
+	if (InstancePtr->UserHdcpProt == XV_HDMIRXSS_HDCP_NONE) {
+		XV_HdmiRx_DdcHdcpDisable(InstancePtr->HdmiRxPtr);
+	} else {
+		XV_HdmiRx_DdcHdcpEnable(InstancePtr->HdmiRxPtr);
+	}
+
+	/* Toggle HPD to get attention of upstream transmitter */
+	XV_HdmiRxSs_ToggleHpd(InstancePtr);
+
+	return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the desired HDCP capability and enables it.
+* The protocol can be set to either both or none. Selective
+* enablement of HDCP 1.4 and 2.2 is not yet supported.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Protocol is the requested content protection scheme of type
+*        XV_HdmiRxSs_HdcpProtocol. Only options currently supported
+*        is both and none.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetCapability(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpProtocol Protocol)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(Protocol <= XV_HDMIRXSS_HDCP_BOTH);
+
+    // Enable HDCP capable for both protocols
+    // DDC slave is enabled
+    switch (Protocol) {
+
+    // Disable HDCP capable for both protocols
+    // DDC slave is disabled
+    case XV_HDMIRXSS_HDCP_NONE:
+      XV_HdmiRx_DdcIntrDisable(InstancePtr->HdmiRxPtr);
+      XV_HdmiRx_DdcHdcpDisable(InstancePtr->HdmiRxPtr);
+      XV_HdmiRxSs_HdcpDisable(InstancePtr);
+      break;
+
+    // Enable HDCP capable for both protocols
+    // DDC slave is enabled
+    default :
+      XV_HdmiRx_DdcIntrEnable(InstancePtr->HdmiRxPtr);
+      XV_HdmiRx_DdcHdcpEnable(InstancePtr->HdmiRxPtr);
+      break;
+  }
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function gets the active HDCP content protection scheme.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  @RequestedScheme is the requested content protection scheme.
+*
+* @note   None.
+*
+******************************************************************************/
+XV_HdmiRxSs_HdcpProtocol XV_HdmiRxSs_HdcpGetProtocol(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  return InstancePtr->HdcpProtocol;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function enables the requested HDCP protocol. This function
+* ensures that the HDCP protocols are mutually exclusive such that
+* either HDCP 1.4 or HDCP 2.2 is enabled and active at any given time.
+* When the protocol is set to None, both HDCP protocols are disabled.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpEnable(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status1 = XST_SUCCESS;
+  int Status2 = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol) {
+
+    /* Disable HDCP 1.4 and HDCP 2.2 */
+    case XV_HDMIRXSS_HDCP_NONE :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        Status1 = XHdcp1x_Disable(InstancePtr->Hdcp14Ptr);
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+        XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_HDCP14, 0);
+#endif
+      }
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        Status2 = XHdcp22Rx_Disable(InstancePtr->Hdcp22Ptr);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+        XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_HDCP22, 0);
+#endif
+      }
+#endif
+      break;
+
+    /* Enable HDCP 1.4 and disable HDCP 2.2 */
+    case XV_HDMIRXSS_HDCP_14 :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        Status1 = XHdcp1x_Enable(InstancePtr->Hdcp14Ptr);
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+        XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_HDCP14, 1);
+#endif
+      }
+      else {
+        Status1 = XST_FAILURE;
+      }
+
+      /* Set DDC peripheral to HDCP 1.4 mode */
+      XV_HdmiRx_DdcHdcp14Mode(InstancePtr->HdmiRxPtr);
+#else
+      Status1 = XST_FAILURE;
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        Status2 = XHdcp22Rx_Disable(InstancePtr->Hdcp22Ptr);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+        XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_HDCP22, 0);
+#endif
+      }
+#endif
+      break;
+
+    /* Enable HDCP 2.2 and disable HDCP 1.4 */
+    case XV_HDMIRXSS_HDCP_22 :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        Status1 = XHdcp1x_Disable(InstancePtr->Hdcp14Ptr);
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+        XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_HDCP14, 0);
+#endif
+      }
+#endif
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        Status2 = XHdcp22Rx_Enable(InstancePtr->Hdcp22Ptr);
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+        XV_HdmiRxSs_LogWrite(InstancePtr, XV_HDMIRXSS_LOG_EVT_HDCP22, 1);
+#endif
+      }
+      else {
+        Status2 = XST_FAILURE;
+      }
+
+      /* Set DDC peripheral to HDCP 2.2 mode */
+      XV_HdmiRx_DdcHdcp22Mode(InstancePtr->HdmiRxPtr);
+#else
+      Status2 = XST_FAILURE;
+#endif
+      break;
+
+    default :
+      return XST_FAILURE;
+  }
+
+  return (Status1 == XST_SUCCESS && Status2 == XST_SUCCESS) ? XST_SUCCESS : XST_FAILURE;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function disables both HDCP 1.4 and 2.2 protocols.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpDisable(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  /* Set protocol to NONE then reset/disable HDCP 1.4 and 2.2 */
+  InstancePtr->HdcpProtocol = XV_HDMIRXSS_HDCP_NONE;
+  Status = XV_HdmiRxSs_HdcpReset(InstancePtr);
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function resets both HDCP 1.4 and 2.2 protocols. This function also
+* disables both HDCP 1.4 and 2.2 protocols.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpReset(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  // Resetting HDCP 1.4 causes the state machine to be enabled, therefore
+  // disable must be called immediately after reset is called.
+  if (InstancePtr->Hdcp14Ptr) {
+    Status = XHdcp1x_Reset(InstancePtr->Hdcp14Ptr);
+    XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+
+    Status = XHdcp1x_Disable(InstancePtr->Hdcp14Ptr);
+    XHdcp1x_Poll(InstancePtr->Hdcp14Ptr); // This is needed to ensure that the previous command is executed.
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  // HDCP 2.2
+  if (InstancePtr->Hdcp22Ptr) {
+    Status = XHdcp22Rx_Reset(InstancePtr->Hdcp22Ptr);
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+
+    Status = XHdcp22Rx_Disable(InstancePtr->Hdcp22Ptr);
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+  }
+#endif
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is enabled.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - TRUE if active protocol is enabled
+*  - FALSE if active protocol is disabled
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsEnabled(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMIRXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_14 :
+      return XHdcp1x_IsEnabled(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_22 :
+      return XHdcp22Rx_IsEnabled(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is authenticated.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - TRUE if active protocol is authenticated
+*  - FALSE if active protocol is not authenticated
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsAuthenticated(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMIRXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_14 :
+      return XHdcp1x_IsAuthenticated(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_22 :
+      return XHdcp22Rx_IsAuthenticated(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol has encryption enabled.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - TRUE if active protocol has encryption enabled
+*  - FALSE if active protocol has encryption disabled
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsEncrypted(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMIRXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_14 :
+      return XHdcp1x_IsEncrypted(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_22 :
+      return XHdcp22Rx_IsEncryptionEnabled(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is busy authenticating.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - TRUE if active protocol is busy authenticating
+*  - FALSE if active protocol is not busy authenticating
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsInProgress(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMIRXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_14 :
+      return XHdcp1x_IsInProgress(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    case XV_HDMIRXSS_HDCP_22 :
+      return XHdcp22Rx_IsInProgress(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is in computations state.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - TRUE if active protocol is in computations state
+*  - FALSE if active protocol is not in computations state
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsInComputations(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+	case XV_HDMIRXSS_HDCP_NONE :
+	  return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+	case XV_HDMIRXSS_HDCP_14 :
+	  return XHdcp1x_IsInComputations(InstancePtr->Hdcp14Ptr);
+#endif
+
+	case XV_HDMIRXSS_HDCP_22 :
+	  return FALSE;
+
+	default :
+	  return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is in wait-for-ready state.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*  - TRUE if active protocol is in computations state
+*  - FALSE if active protocol is not in computations state
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsInWaitforready(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+	case XV_HDMIRXSS_HDCP_NONE :
+	  return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+	case XV_HDMIRXSS_HDCP_14 :
+	  return XHdcp1x_IsInWaitforready(InstancePtr->Hdcp14Ptr);
+#endif
+
+	case XV_HDMIRXSS_HDCP_22 :
+	  return FALSE;
+
+	default :
+	  return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets pointers to the HDCP 1.4 and HDCP 2.2 keys.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_HdcpSetKey(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_HdcpKeyType KeyType, u8 *KeyPtr)
+{
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+  Xil_AssertVoid((KeyType == XV_HDMIRXSS_KEY_HDCP22_LC128)   ||
+                   (KeyType == XV_HDMIRXSS_KEY_HDCP22_PRIVATE)   ||
+                    (KeyType == XV_HDMIRXSS_KEY_HDCP14));
+
+  switch (KeyType) {
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2 LC128
+    case XV_HDMIRXSS_KEY_HDCP22_LC128 :
+      InstancePtr->Hdcp22Lc128Ptr = KeyPtr;
+      break;
+
+    // HDCP 2.2 Private key
+    case XV_HDMIRXSS_KEY_HDCP22_PRIVATE :
+      InstancePtr->Hdcp22PrivateKeyPtr = KeyPtr;
+      break;
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_KEY_HDCP14 :
+      InstancePtr->Hdcp14KeyPtr = KeyPtr;
+#endif
+      break;
+
+    default :
+      break;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function reports the HDCP information.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param buff The buffer to print to
+* @param buff_size The size of the buffer
+
+* @return The number of bytes written to buff.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpInfo(XV_HdmiRxSs *InstancePtr, char *buff, int buff_size)
+{
+  int strSize = 0;
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMIRXSS_HDCP_NONE :
+      strSize = scnprintf(buff+strSize, buff_size-strSize,
+          "\r\nHDCP RX is disabled\r\n");
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        if (XHdcp1x_IsEnabled(InstancePtr->Hdcp14Ptr)) {
+          strSize = scnprintf(buff+strSize, buff_size-strSize,
+              "\r\nHDCP 1.4 RX Info\r\n" \
+              "Encryption : %s.\r\n",
+              (XHdcp1x_IsEncrypted(InstancePtr->Hdcp14Ptr) ? "Enabled" : "Disabled"));
+
+          XDebug_SetDebugBufPrintf(buff,buff_size, &strSize);
+          XHdcp1x_Info(InstancePtr->Hdcp14Ptr);
+          XDebug_SetDebugBufPrintf(NULL,0, NULL);
+          // Route debug output to xil_printf
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+          XDebug_SetDebugPrintf((void *)printk);
+#else
+          XDebug_SetDebugPrintf((void *)_printk);
+#endif
+        }
+        else {
+          strSize = scnprintf(buff+strSize, buff_size-strSize,
+              "\r\nHDCP 1.4 RX is disabled\r\n");
+        }
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        if (XHdcp22Rx_IsEnabled(InstancePtr->Hdcp22Ptr)) {
+          strSize = XHdcp22Rx_LogShow(InstancePtr->Hdcp22Ptr, buff, buff_size);
+          strSize += scnprintf(buff+strSize, buff_size-strSize,
+              "HDCP 2.2 RX Info\r\n");
+          XDebug_SetDebugBufPrintf(buff,buff_size, &strSize);
+          XHdcp22Rx_Info(InstancePtr->Hdcp22Ptr);
+          XDebug_SetDebugBufPrintf(NULL,0, NULL);
+          // Route debug output to xil_printf
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+          XDebug_SetDebugPrintf((void *)printk);
+#else
+          XDebug_SetDebugPrintf((void *)_printk);
+#endif
+        }
+        else {
+          strSize = scnprintf(buff+strSize, buff_size-strSize, "\r\nHDCP 2.2 RX is disabled\r\n");
+        }
+      }
+      break;
+#endif
+
+    default:
+      strSize = scnprintf(buff+strSize, buff_size-strSize, "\r\nHDCP info unknown?\r\n");
+  }
+  return strSize;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP logging level.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Verbose is set to TRUE to enable detailed logging.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_HdcpSetInfoDetail(XV_HdmiRxSs *InstancePtr, u8 Verbose)
+{
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  if (Verbose) {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+   // HDCP 1.4
+   if (InstancePtr->Hdcp14Ptr) {
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+     XHdcp1x_SetDebugLogMsg((void *)printk);
+#else
+     XHdcp1x_SetDebugLogMsg((void *)_printk);
+#endif
+   }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+   // HDCP 2.2
+   if (InstancePtr->Hdcp22Ptr) {
+     XHdcp22Rx_LogReset(InstancePtr->Hdcp22Ptr, TRUE);
+   }
+#endif
+  }
+
+  else {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    if (InstancePtr->Hdcp14Ptr) {
+      XHdcp1x_SetDebugLogMsg(NULL);
+    }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    if (InstancePtr->Hdcp22Ptr) {
+      XHdcp22Rx_LogReset(InstancePtr->Hdcp22Ptr, FALSE);
+    }
+#endif
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function copies the HDCP repeater topology for the active protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param TopologyPtr is a pointer to the topology structure.
+*
+* @return .
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetTopology(XV_HdmiRxSs *InstancePtr, void *TopologyPtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(TopologyPtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopology(InstancePtr->Hdcp14Ptr, ((XHdcp1x_RepeaterExchange*)(TopologyPtr)));
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopology(InstancePtr->Hdcp22Ptr, (XHdcp22_Rx_Topology*)(TopologyPtr));
+      } else {
+        Status = XST_FAILURE;
+      }
+    break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function copies the HDCP repeater topology list for the active
+* protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param ListPtr is a pointer to the Receiver ID list.
+* @param ListSize is the number of Receiver IDs in the list.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetTopologyReceiverIdList(XV_HdmiRxSs *InstancePtr, u8 *ListPtr, u32 ListSize)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(ListPtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopologyKSVList(InstancePtr->Hdcp14Ptr, ListPtr,	ListSize);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyReceiverIdList(InstancePtr->Hdcp22Ptr, ListPtr, ListSize);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default :
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets various fields inside the HDCP repeater topology.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Field indicates what field of the topology structure to update.
+* @param Value is the value assigned to the field of the topology structure.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetTopologyField(XV_HdmiRxSs *InstancePtr,
+      XV_HdmiRxSs_HdcpTopologyField Field, u32 Value)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(Field < XV_HDMIRXSS_HDCP_TOPOLOGY_INVALID);
+
+  switch (Field)
+  {
+	  case XV_HDMIRXSS_HDCP_TOPOLOGY_DEPTH:
+      return XV_HdmiRxSs_HdcpSetTopologyDepth(InstancePtr, Value);
+	  case XV_HDMIRXSS_HDCP_TOPOLOGY_DEVICECNT:
+      return XV_HdmiRxSs_HdcpSetTopologyDeviceCnt(InstancePtr, Value);
+	  case XV_HDMIRXSS_HDCP_TOPOLOGY_MAXDEVSEXCEEDED:
+      return XV_HdmiRxSs_HdcpSetTopologyMaxDevsExceeded(InstancePtr, Value);
+	  case XV_HDMIRXSS_HDCP_TOPOLOGY_MAXCASCADEEXCEEDED:
+      return XV_HdmiRxSs_HdcpSetTopologyMaxCascadeExceeded(InstancePtr, Value);
+	  case XV_HDMIRXSS_HDCP_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM:
+      return XV_HdmiRxSs_HdcpSetTopologyHdcp2LegacyDeviceDownstream(InstancePtr, Value);
+	  case XV_HDMIRXSS_HDCP_TOPOLOGY_HDCP1DEVICEDOWNSTREAM:
+      return XV_HdmiRxSs_HdcpSetTopologyHdcp1DeviceDownstream(InstancePtr, Value);
+    default:
+      return XST_FAILURE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology depth for the active
+* protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Depth is the Repeater cascade depth.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpSetTopologyDepth(XV_HdmiRxSs *InstancePtr, u32 Depth)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopologyField(InstancePtr->Hdcp14Ptr,
+          XHDCP1X_TOPOLOGY_DEPTH, Depth);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyField(InstancePtr->Hdcp22Ptr,
+          XHDCP22_RX_TOPOLOGY_DEPTH, Depth);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology device count for the active
+* protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param DeviceCnt is the Total number of connected downstream devices.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpSetTopologyDeviceCnt(XV_HdmiRxSs *InstancePtr, u32 DeviceCnt)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopologyField(InstancePtr->Hdcp14Ptr,
+          XHDCP1X_TOPOLOGY_DEVICECNT, DeviceCnt);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyField(InstancePtr->Hdcp22Ptr,
+          XHDCP22_RX_TOPOLOGY_DEVICECNT, DeviceCnt);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology maximum devices exceeded
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Value is either TRUE or FALSE.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpSetTopologyMaxDevsExceeded(XV_HdmiRxSs *InstancePtr, u8 Value)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopologyField(InstancePtr->Hdcp14Ptr,
+          XHDCP1X_TOPOLOGY_MAXDEVSEXCEEDED, Value);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyField(InstancePtr->Hdcp22Ptr,
+          XHDCP22_RX_TOPOLOGY_MAXDEVSEXCEEDED, Value);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology maximum cascade exceeded
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Value is either TRUE or FALSE.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpSetTopologyMaxCascadeExceeded(XV_HdmiRxSs *InstancePtr, u8 Value)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopologyField(InstancePtr->Hdcp14Ptr,
+          XHDCP1X_TOPOLOGY_MAXCASCADEEXCEEDED, Value);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyField(InstancePtr->Hdcp22Ptr,
+          XHDCP22_RX_TOPOLOGY_MAXCASCADEEXCEEDED, Value);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology HDCP2 legacy device
+* downstream flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Value is either TRUE or FALSE.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpSetTopologyHdcp2LegacyDeviceDownstream(XV_HdmiRxSs *InstancePtr, u8 Value)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  Value = Value;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyField(InstancePtr->Hdcp22Ptr,
+          XHDCP22_RX_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM, Value);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology HDCP 1.x repeater downstream
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Value is either TRUE or FALSE.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiRxSs_HdcpSetTopologyHdcp1DeviceDownstream(XV_HdmiRxSs *InstancePtr, u8 Value)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  Value = Value;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyField(InstancePtr->Hdcp22Ptr,
+          XHDCP22_RX_TOPOLOGY_HDCP1DEVICEDOWNSTREAM, Value);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater topology update flag, indicating that
+* the topology is ready for upstream propagation.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Value is either TRUE or FALSE.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetTopologyUpdate(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // None
+    case XV_HDMIRXSS_HDCP_NONE:
+      Status = XST_FAILURE;
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetTopologyUpdate(InstancePtr->Hdcp14Ptr);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Rx_SetTopologyUpdate(InstancePtr->Hdcp22Ptr);
+      } else {
+        Status = XST_FAILURE;
+      }
+      break;
+#endif
+
+    default:
+      Status = XST_FAILURE;
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function gets the repeater management content stream type.
+* When the protocol is HDCP 1.4 the stream type is always Type 0.
+* For HDCP 2.2 the stream type is extracted from the HDCP 2.2
+* stream manage message.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+XV_HdmiRxSs_HdcpContentStreamType XV_HdmiRxSs_HdcpGetContentStreamType(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int StreamType;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      StreamType = XV_HDMIRXSS_HDCP_STREAMTYPE_0;
+      break;
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        StreamType = XHdcp22Rx_GetContentStreamType(InstancePtr->Hdcp22Ptr);
+      } else {
+        StreamType = XV_HDMIRXSS_HDCP_STREAMTYPE_0;
+      }
+      break;
+#endif
+
+    default:
+      StreamType = XV_HDMIRXSS_HDCP_STREAMTYPE_0;
+  }
+
+  return (XV_HdmiRxSs_HdcpContentStreamType) StreamType;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function checks if the HDMI receiver is an HDCP repeater
+* upstream interface for the active protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+*
+* @return
+*   - TRUE if repeater upstream interface.
+*   - FALSE if not repeater upstream interface.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpIsRepeater(XV_HdmiRxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = (int)FALSE;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMIRXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Status = XHdcp1x_IsRepeater(InstancePtr->Hdcp14Ptr);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMIRXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Status = XHdcp22Rx_IsRepeater(InstancePtr->Hdcp22Ptr);
+      }
+      break;
+#endif
+
+    default:
+      Status = (int)FALSE;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_RX
+/*****************************************************************************/
+/**
+*
+* This function enables the Repeater functionality for the HDCP protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiRxSs instance.
+* @param Set is TRUE to enable and FALSE to disable repeater.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_HdcpSetRepeater(XV_HdmiRxSs *InstancePtr, u8 Set)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  if (InstancePtr->Hdcp14Ptr) {
+    XHdcp1x_SetRepeater(InstancePtr->Hdcp14Ptr, Set);
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_RX_NUM_INSTANCES
+  // HDCP 2.2
+  if (InstancePtr->Hdcp22Ptr) {
+    XHdcp22Rx_SetRepeater(InstancePtr->Hdcp22Ptr, Set);
+  }
+#endif
+
+  return XST_SUCCESS;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_log.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-rx/xv_hdmirxss_log.c
@@ -0,0 +1,331 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xv_hdmirxss_log.c
+ *
+ *
+ * @note    None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   YH   17/08/16 Initial release.
+ * 1.01  MMO  03/01/17 Add compiler option(XV_HDMIRXSS_LOG_ENABLE) to enable
+ *                         Log
+ * 1.4   YH   07/07/17 Add new log type XV_HDMIRXSS_LOG_EVT_SETSTREAM_ERR
+ * 5.0   EB   16/01/18 Added new log XV_HDMIRXSS_LOG_EVT_PIX_REPEAT_ERR
+ *            23/01/18 Minor cleanup
+ *       MMO  05/02/18 Added new log XV_HDMIRXSS_LOG_EVT_SYNCEST
+ * 5.4   EB   06/08/19 Added new log XV_HDMIRXSS_LOG_EVT_VICERROR
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xv_hdmirxss.h"
+
+/**************************** Function Prototypes *****************************/
+
+/**************************** Function Definitions ****************************/
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+/*****************************************************************************/
+/**
+* This function will reset the driver's logging mechanism.
+*
+* @param    InstancePtr is a pointer to the xv_hdmirxss core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_LogReset(XV_HdmiRxSs *InstancePtr)
+{
+    /* Verify arguments. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    InstancePtr->Log.HeadIndex = 0;
+    InstancePtr->Log.TailIndex = 0;
+}
+
+/*****************************************************************************/
+/**
+* This function will insert an event in the driver's logginc mechanism.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRxSs core instance.
+* @param    Evt is the event type to log.
+* @param    Data is the associated data for the event.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiRxSs_LogWrite(XV_HdmiRxSs *InstancePtr, XV_HdmiRxSs_LogEvent Evt, u8 Data)
+{
+    /* Verify arguments. */
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(Evt <= (XV_HDMIRXSS_LOG_EVT_DUMMY));
+    Xil_AssertVoid(Data < 0xFF);
+
+    /* Write data and event into log buffer */
+    InstancePtr->Log.DataBuffer[InstancePtr->Log.HeadIndex] =
+            (Data << 8) | Evt;
+
+	/* Update head pointer if reached to end of the buffer */
+	if (InstancePtr->Log.HeadIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) /
+					sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+		/* Clear pointer */
+		InstancePtr->Log.HeadIndex = 0;
+	}
+	else {
+		/* Increment pointer */
+		InstancePtr->Log.HeadIndex++;
+	}
+
+	/* Check tail pointer. When the two pointer are equal, then the buffer
+	 * is full. In this case then increment the tail pointer as well to
+	 * remove the oldest entry from the buffer. */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) /
+					sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will read the last event from the log.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRxSs core instance.
+*
+* @return   The log data.
+*
+* @note     None.
+*
+******************************************************************************/
+u16 XV_HdmiRxSs_LogRead(XV_HdmiRxSs *InstancePtr)
+{
+    u16 Log;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* Check if there is any data in the log */
+    if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+        Log = 0;
+    }
+    else {
+        Log = InstancePtr->Log.DataBuffer[InstancePtr->Log.TailIndex];
+
+        /* Increment tail pointer */
+        if (InstancePtr->Log.TailIndex ==
+            (u8)((sizeof(InstancePtr->Log.DataBuffer) /
+					sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+            InstancePtr->Log.TailIndex = 0;
+        }
+        else {
+            InstancePtr->Log.TailIndex++;
+        }
+    }
+
+    return Log;
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will print the entire log.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiRxSs core instance.
+* @param	buff Buffer to print to
+* @param	buff_size size off buff passed
+*
+* @return   number of characters written to buff
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiRxSs_LogShow(XV_HdmiRxSs *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+#ifdef XV_HDMIRXSS_LOG_ENABLE
+    u16 Log;
+    u8 Evt;
+    u8 Data;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+	strSize = scnprintf(buff+strSize, buff_size-strSize,
+			"\r\n\n\nHDMI RX log\r\n" \
+			"------\r\n");
+
+    /* Read log data */
+    Log = XV_HdmiRxSs_LogRead(InstancePtr);
+
+    while (Log != 0 && (buff_size - strSize) > 30 ) {
+        /* Event */
+        Evt = Log & 0xff;
+
+        /* Data */
+        Data = (Log >> 8) & 0xFF;
+
+        switch (Evt) {
+        case (XV_HDMIRXSS_LOG_EVT_NONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"HDMI RXSS log end\r\n-------\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_HDMIRX_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing HDMI RX core....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_VTC_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing VTC core....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_HDCPTIMER_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing AXI Timer core....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_HDCP14_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing HDCP 1.4 core....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_HDCP22_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing HDCP 2.2 core....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_START):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Start HDMI RX Subsystem....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_STOP):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Stop HDMI RX Subsystem....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Reset HDMI RX Subsystem....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_CONNECT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX cable is connected....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_DISCONNECT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX cable is disconnected....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_LINKSTATUS):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Link Status Error....\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_STREAMUP):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Stream is Up\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_STREAMDOWN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Stream is Down\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_STREAMINIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Stream Start\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_SETSTREAM):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Stream Init\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_SETSTREAM_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Error: RX Stream Reference Clock = 0\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_REFCLOCKCHANGE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX TMDS reference clock change\r\n");
+            break;
+         case (XV_HDMIRXSS_LOG_EVT_HDCP14):
+              if (Data) {
+            		strSize += scnprintf(buff+strSize, buff_size-strSize,
+            				"RX HDCP 1.4 Enabled\r\n");
+              } else {
+            		strSize += scnprintf(buff+strSize, buff_size-strSize,
+            				"RX HDCP 1.4 Disabled\r\n");
+              }
+            break;
+         case (XV_HDMIRXSS_LOG_EVT_HDCP22):
+              if (Data) {
+            		strSize += scnprintf(buff+strSize, buff_size-strSize,
+            				"RX HDCP 2.2 Enabled\r\n");
+              } else {
+            		strSize += scnprintf(buff+strSize, buff_size-strSize,
+            				"RX HDCP 2.2 Disabled\r\n");
+              }
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_DVIMODE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX mode changed to DVI\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_HDMIMODE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX mode changed to HDMI\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_SYNCLOSS):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Sync Loss detected\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_PIX_REPEAT_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Unsupported Pixel Repetition: %d\r\n", Data);
+			break;
+		case (XV_HDMIRXSS_LOG_EVT_SYNCEST):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"RX Sync Loss recovered\r\n");
+            break;
+        case (XV_HDMIRXSS_LOG_EVT_VICERROR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Vic and video timing mismatch\r\n");
+			break;
+        default:
+        	strSize += scnprintf(buff+strSize, buff_size-strSize,
+        			"Unknown event: %i\r\n", Evt);
+            break;
+        }
+
+		if((buff_size - strSize) > 30) {
+	        /* Read log data */
+	        Log = XV_HdmiRxSs_LogRead(InstancePtr);
+		} else {
+			Log = 0;
+		}
+    }
+#else
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"\r\n INFO:: HDMIRXSS Log Feature is Disabled \r\n");
+#endif
+    return strSize;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx.c
@@ -0,0 +1,2087 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitx.c
+*
+* This is the main file for Xilinx HDMI TX core. Please see xv_hdmitx.h for
+* more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.01  yh     15/01/16 Add 3D Support
+* 1.02  MG     09/03/16 Added XV_HdmiTx_SetHdmiMode and XV_HdmiTx_SetDviMode
+* 1.03  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XV_HdmiTx_CfgInitialize
+* 1.04  YH     27/07/16 Remove checking VideoMode<(XVIDC_VM_NUM_SUPPORTED));
+* 1.05  YH     17/08/16 Add XV_HdmiTx_SetAxiClkFreq
+*                       Move XV_HdmiTx_DdcInit to XV_HdmiTx_SetAxiClkFreq
+*                       squash unused variable compiler warning
+* 1.06  MG     07/03/17 Updated XV_HdmiTx_Auxsend with packet ready check
+* 1.07  YH     19/07/17 Added Video Masking Check API
+* 1.08  YH     06/10/17 Added function XV_HdmiTx_SetAudioFormat and function
+*                           XV_HdmiTx_GetAudioFormat
+*       EB     10/10/17 Updated XV_HdmiTx_Scrambler to always enable scrambler
+*                           for HDMI 2.0 resolutions
+* 1.09  MMO    19/12/17 Added XV_HdmiTx_SetTmdsClk API
+* 2.00  YH     16/01/18 Added dedicated reset for each clock domain
+*                       Added bridge unlock interrupt
+*                       Added PIO_OUT to set GCP_AVMUTE
+*       EB     18/01/18 Moved VicTable to Hdmi Common library
+*                       Updated function XV_HdmiTx_SetTmdsClk and renamed to
+*                           XV_HdmiTx_GetTmdsClk
+*                       Updated function XV_HdmiTx_SetStream
+*                       Moved VicTable, XV_HdmiTx_Aux to Hdmi Common library
+*       EB     23/01/18 Updated XV_HdmiTx_SetAudioChannels to fix an issue
+*                           where setting audio channel value will unmute the
+*                           audio regardless of the current status
+* 2.02  MMO    11/08/18 Added Bridge Overflow and Bridge Underflow (PIO IN)
+*       EB     14/08/18 Updated XV_HdmiTx_CfgInitialize to initialize
+*                       	HPD pulse periods
+* 2.03  EB     28/03/19 Disable PIO Interrupt for XV_HdmiTx_DdcWrite and
+*                           XV_HdmiTx_DdcRead APIs to prevent another DDC
+*                           transactions from happening in the middle of a DDC
+*                           transaction
+*       EB     16/07/19 Replaced sampling rate of 4 with 2 at the API
+*                           XV_HdmiTx_SetSampleRate
+* 2.50  EB     02/12/18 Added 3D Audio Support
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmitx.h"
+#include "xil_printf.h"
+#include <linux/string.h>
+#include <linux/delay.h>
+
+/************************** Constant Definitions *****************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+static int XV_HdmiTx_DdcGetAck(XV_HdmiTx *InstancePtr);
+static int XV_HdmiTx_DdcWaitForDone(XV_HdmiTx *InstancePtr);
+static u32 XV_HdmiTx_DdcWriteCommand(XV_HdmiTx *InstancePtr, u32 Cmd);
+static u8 XV_HdmiTx_DdcReadData(XV_HdmiTx *InstancePtr);
+
+/**************************** Type Definitions *******************************/
+
+/************************** Function Prototypes ******************************/
+
+static void StubCallback(void *Callback);
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function initializes the HDMI TX core. This function must be called
+* prior to using the HDMI TX core. Initialization of the HDMI TX includes
+* setting up the instance data and ensuring the hardware is in a quiescent
+* state.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    CfgPtr points to the configuration structure associated with
+*       the HDMI TX core.
+* @param    EffectiveAddr is the base address of the device. If address
+*       translation is being used, then this parameter must reflect the
+*       virtual base address. Otherwise, the physical address should be
+*       used.
+*
+* @return
+*       - XST_SUCCESS if XV_HdmiTx_CfgInitialize was successful.
+*       - XST_FAILURE if HDMI TX PIO ID mismatched.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_CfgInitialize(XV_HdmiTx *InstancePtr, XV_HdmiTx_Config *CfgPtr,
+    UINTPTR EffectiveAddr)
+{
+    u32 RegValue;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(CfgPtr != NULL);
+    Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)0x0);
+
+    /* Setup the instance */
+    (void)memset((void *)InstancePtr, 0, sizeof(XV_HdmiTx));
+    (void)memcpy((void *)&(InstancePtr->Config), (const void *)CfgPtr,
+        sizeof(XV_HdmiTx_Config));
+    InstancePtr->Config.BaseAddress = EffectiveAddr;
+
+    /* Set all handlers to stub values, let user configure this data later */
+    InstancePtr->ConnectCallback = (XV_HdmiTx_Callback)((void *)StubCallback);
+    InstancePtr->IsConnectCallbackSet = (FALSE);
+
+    InstancePtr->ToggleCallback = (XV_HdmiTx_Callback)((void *)StubCallback);
+    InstancePtr->IsToggleCallbackSet = (FALSE);
+
+    InstancePtr->VsCallback = (XV_HdmiTx_Callback)((void *)StubCallback);
+    InstancePtr->IsVsCallbackSet = (FALSE);
+
+    InstancePtr->StreamDownCallback =(XV_HdmiTx_Callback)((void *)StubCallback);
+    InstancePtr->IsStreamDownCallbackSet = (FALSE);
+
+    InstancePtr->StreamUpCallback = (XV_HdmiTx_Callback)((void *)StubCallback);
+    InstancePtr->IsStreamUpCallbackSet = (FALSE);
+
+    /* Clear HDMI variables */
+    XV_HdmiTx_Clear(InstancePtr);
+
+    /* Disable scrambler override function */
+    InstancePtr->Stream.OverrideScrambler = (FALSE);
+
+    // Set stream status
+    InstancePtr->Stream.State = XV_HDMITX_STATE_STREAM_DOWN;
+    // The stream is down
+
+    // Clear connected flag
+    InstancePtr->Stream.IsConnected = (FALSE);
+
+    /* Reset all peripherals */
+    XV_HdmiTx_PioDisable(InstancePtr);
+    XV_HdmiTx_DdcDisable(InstancePtr);
+    XV_HdmiTx_AudioDisable(InstancePtr);
+    XV_HdmiTx_AuxDisable(InstancePtr);
+
+    XV_HdmiTx_PioIntrClear(InstancePtr);
+    XV_HdmiTx_DdcIntrClear(InstancePtr);
+
+    /* Read PIO peripheral Identification register */
+    RegValue = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+    (XV_HDMITX_PIO_ID_OFFSET));
+
+    RegValue = ((RegValue) >> (XV_HDMITX_SHIFT_16)) &
+    (XV_HDMITX_MASK_16);
+    if (RegValue != (XV_HDMITX_PIO_ID)) {
+        return (XST_FAILURE);
+    }
+
+    /* PIO: Set event rising edge masks */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+    (XV_HDMITX_PIO_IN_EVT_RE_OFFSET),
+            (XV_HDMITX_PIO_IN_BRDG_UNDERFLOW_MASK) |
+            (XV_HDMITX_PIO_IN_BRDG_OVERFLOW_MASK) |
+            (XV_HDMITX_PIO_IN_HPD_TOGGLE_MASK) |
+            (XV_HDMITX_PIO_IN_HPD_MASK) |
+            (XV_HDMITX_PIO_IN_VS_MASK) |
+            (XV_HDMITX_PIO_IN_LNK_RDY_MASK)
+        );
+
+    /* PIO: Set event falling edge masks */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+    (XV_HDMITX_PIO_IN_EVT_FE_OFFSET),
+            (XV_HDMITX_PIO_IN_BRDG_LOCKED_MASK) |
+            (XV_HDMITX_PIO_IN_HPD_MASK) |
+            (XV_HDMITX_PIO_IN_LNK_RDY_MASK)
+        );
+
+    /* Set the Timegrid for HPD Pulse for Connect and Toggle Event */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+                       XV_HDMITX_HPD_TIMEGRID_OFFSET,
+                       XV_HdmiTx_GetTime1Ms(InstancePtr));
+
+    /* Toggle HPD Pulse (50ms - 99ms)*/
+	RegValue = ((99 << XV_HDMITX_SHIFT_16) | /* 99 ms on Bit 31:16 */
+	            (50)); /* 50 ms on Bit 15:0 */
+
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+		           XV_HDMITX_TOGGLE_CONF_OFFSET,
+			   RegValue);
+
+    /* HPD/Connect Trigger (100ms + 0ms)*/
+	RegValue = ((10 << XV_HDMITX_SHIFT_16) | /* 10 ms on Bit 31:16 */
+	            (100)); /* 100 ms on Bit 15:0 */
+
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+		           XV_HDMITX_CONNECT_CONF_OFFSET,
+			   RegValue);
+
+    /* Enable the PIO peripheral interrupt */
+    XV_HdmiTx_PioIntrEnable(InstancePtr);
+
+    /* Enable the PIO peripheral */
+    XV_HdmiTx_PioEnable(InstancePtr);
+
+    /* Set HDMI mode */
+    XV_HdmiTx_SetHdmiMode(InstancePtr);
+
+    /* Enable the AUX peripheral */
+    /* The aux peripheral is enabled at stream up */
+    //XV_HdmiTx_AuxEnable(InstancePtr);
+
+    /* Enable audio */
+    /* The audio peripheral is enabled at stream up */
+    //XV_HdmiTx_AudioEnable(InstancePtr);
+
+    /* Reset the hardware and set the flag to indicate the driver is ready */
+    InstancePtr->IsReady = (u32)(XIL_COMPONENT_IS_READY);
+
+    return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the AXI4-Lite Clock Frequency
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    ClkFreq specifies the value that needs to be set.
+*
+* @return
+*
+*
+* @note     This is required after a reset or init.
+*
+******************************************************************************/
+void XV_HdmiTx_SetAxiClkFreq(XV_HdmiTx *InstancePtr, u32 ClkFreq)
+{
+	InstancePtr->CpuClkFreq = ClkFreq;
+
+	/* Initialize DDC */
+	XV_HdmiTx_DdcInit(InstancePtr, InstancePtr->CpuClkFreq);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the core into HDMI mode.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*
+*
+* @note     This is required after a reset or init.
+*
+******************************************************************************/
+void XV_HdmiTx_SetHdmiMode(XV_HdmiTx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Set mode bit in core */
+    XV_HdmiTx_SetMode(InstancePtr);
+
+    /* Set flag in structure */
+    InstancePtr->Stream.IsHdmi = TRUE;
+
+    /* Enable the AUX peripheral */
+    /* The aux peripheral is enabled at stream up */
+    XV_HdmiTx_AuxEnable(InstancePtr);
+
+    /* Enable audio */
+    /* The audio peripheral is enabled at stream up */
+    XV_HdmiTx_AudioEnable(InstancePtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the core into DVI mode.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*
+*
+* @note     This is required after a reset or init.
+*
+******************************************************************************/
+void XV_HdmiTx_SetDviMode(XV_HdmiTx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Disable audio peripheral */
+    XV_HdmiTx_AudioDisable(InstancePtr);
+
+    /* Disable aux peripheral */
+    XV_HdmiTx_AuxDisable(InstancePtr);
+
+    /* Clear mode bit in core */
+    XV_HdmiTx_ClearMode(InstancePtr);
+
+    /* Clear flag in structure */
+    InstancePtr->Stream.IsHdmi = FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function clear the HDMI TX variables and sets it to the defaults.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*
+*
+* @note     This is required after a reset or init.
+*
+******************************************************************************/
+void XV_HdmiTx_Clear(XV_HdmiTx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides video identification code of video mode.
+*
+* @param    VideoMode specifies resolution identifier.
+*
+* @return   Video identification code defined in the VIC table.
+*
+* @note     None.
+*
+******************************************************************************/
+u8 XV_HdmiTx_LookupVic(XVidC_VideoMode VideoMode)
+{
+    XHdmiC_VicTable const *Entry;
+    u8 Index;
+
+    for (Index = 0; Index < sizeof(VicTable)/sizeof(XHdmiC_VicTable);
+        Index++) {
+      Entry = &VicTable[Index];
+      if (Entry->VmId == VideoMode)
+        return (Entry->Vic);
+    }
+    return 0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets and return the TMDS Clock based on Video Parameter
+*
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    VideoMode specifies resolution identifier.
+* @param    ColorFormat specifies the type of color format.
+*       - 0 = XVIDC_CSF_RGB
+*       - 1 = XVIDC_CSF_YCRCB_444
+*       - 2 = XVIDC_CSF_YCRCB_422
+*       - 3 = XVIDC_CSF_YCRCB_420
+* @param    Bpc specifies the color depth/bits per color component.
+*       - 6 = XVIDC_BPC_6
+*       - 8 = XVIDC_BPC_8
+*       - 10 = XVIDC_BPC_10
+*       - 12 = XVIDC_BPC_12
+*       - 16 = XVIDC_BPC_16
+*
+* @return
+*       - TMDS Clock
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiTx_GetTmdsClk (XV_HdmiTx *InstancePtr,
+    XVidC_VideoMode VideoMode,
+    XVidC_ColorFormat ColorFormat,
+    XVidC_ColorDepth Bpc) {
+
+    u32 TmdsClock;
+
+    /* Calculate reference clock. First calculate the pixel clock */
+	/* TODO - Not same as BM code */
+    if (VideoMode != XVIDC_VM_CUSTOM) {
+		TmdsClock = XVidC_GetPixelClockHzByVmId(VideoMode);
+    } else {
+		TmdsClock = XVidC_GetPixelClockHzByHVFr(InstancePtr->Stream.Video.Timing.HTotal,
+                                              InstancePtr->Stream.Video.Timing.F0PVTotal,
+                                              InstancePtr->Stream.Video.FrameRate);
+    }
+
+    /* Store the pixel clock in the structure */
+    InstancePtr->Stream.PixelClk = TmdsClock;
+
+    /* YUV420 */
+    if (ColorFormat == (XVIDC_CSF_YCRCB_420)) {
+        /* In YUV420 the tmds clock is divided by two*/
+        TmdsClock = TmdsClock / 2;
+    }
+
+    /* RGB, YUV444 and YUV420 */
+    if ( ColorFormat != XVIDC_CSF_YCRCB_422 ) {
+
+        switch (Bpc) {
+
+            // 10-bits
+            case XVIDC_BPC_10 :
+                TmdsClock = TmdsClock * 5 / 4;
+                break;
+
+            // 12-bits
+            case XVIDC_BPC_12 :
+                TmdsClock = TmdsClock * 3 / 2;
+                break;
+
+            // 16-bits
+            case XVIDC_BPC_16 :
+                TmdsClock = TmdsClock * 2;
+                break;
+
+            // 8-bits
+            default:
+                TmdsClock = TmdsClock;
+                break;
+        }
+    }
+
+    return TmdsClock;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function controls the scrambler. Requires TMDSClock to be up to date in
+* order to force enable scrambler when TMDSClock > 340MHz.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - XST_SUCCESS if HDMI 2.0
+*       - XST_FAILURE if HDMI 1.4
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_Scrambler(XV_HdmiTx *InstancePtr) {
+    u8 DdcBuf[2];
+    u32 Status;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Check if the sink is HDMI 2.0
+    // Check if the TMDS Clock is higher than 340MHz
+    // Check scrambler flag
+	if (InstancePtr->Stream.IsHdmi20 &&
+			((InstancePtr->Stream.TMDSClock > 340000000 &&
+					InstancePtr->Stream.OverrideScrambler != (TRUE))
+					|| InstancePtr->Stream.IsScrambled)) {
+		XV_HdmiTx_SetScrambler(InstancePtr, (TRUE));
+	}
+	// Clear
+	else {
+		XV_HdmiTx_SetScrambler(InstancePtr, (FALSE));
+	}
+
+    // Update TMDS configuration
+    // Only when it is a HDMI 2.0 sink device
+    if (InstancePtr->Stream.IsHdmi20) {
+
+        DdcBuf[0] = 0x20;   // Offset scrambler status
+        Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 1,
+        (u8*)&DdcBuf, (FALSE));
+
+        // Check if write was successful
+        if (Status == (XST_SUCCESS)) {
+
+            // Read TMDS configuration
+            Status = XV_HdmiTx_DdcRead(InstancePtr, 0x54, 1,
+            (u8*)&DdcBuf, (TRUE));
+
+            // The result is in ddc_buf[0]
+            // Clear scrambling enable bit
+            DdcBuf[0] &= 0xfe;
+
+            // Set scrambler bit if scrambler is enabled
+            if (InstancePtr->Stream.IsScrambled)
+                DdcBuf[0] |= 0x01;
+
+            // Copy buf[0] to buf[1]
+            DdcBuf[1] = DdcBuf[0];
+
+            // Offset
+            DdcBuf[0] = 0x20;   // Offset scrambler status
+
+            // Write back TMDS configuration
+            Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 2,
+            (u8*)&DdcBuf, (TRUE));
+        }
+
+        // Write failed
+        else {
+            return XST_FAILURE;
+        }
+    }
+    return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function controls the TMDS clock ratio
+*
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - XST_SUCCESS if HDMI 2.0
+*       - XST_FAILURE if HDMI 1.4
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_ClockRatio(XV_HdmiTx *InstancePtr) {
+    u8 DdcBuf[2];
+    u32 Status;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Update TMDS configuration
+    // Only when it is a HDMI 2.0 sink device
+    if (InstancePtr->Stream.IsHdmi20) {
+
+        DdcBuf[0] = 0x20;   // Offset scrambler status
+        Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (FALSE));
+
+        // Check if write was successful
+        if (Status == (XST_SUCCESS)) {
+
+            // Read TMDS configuration
+            Status = XV_HdmiTx_DdcRead(InstancePtr, 0x54, 1,
+                (u8*)&DdcBuf, (TRUE));
+
+            // The result is in ddc_buf[0]
+            // Clear TMDS clock ration bit (1)
+            DdcBuf[0] &= 0xfd;
+
+            /* Set the TMDS clock ratio bit if the bandwidth is
+                higher than 3.4 Gbps */
+            if (InstancePtr->Stream.TMDSClockRatio) {
+                DdcBuf[0] |= 0x02;
+            }
+
+            // Copy buf[0] to buf[1]
+            DdcBuf[1] = DdcBuf[0];
+
+            // Offset
+            DdcBuf[0] = 0x20;   // Offset scrambler status
+
+            // Write back TMDS configuration
+            Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 2,
+                (u8*)&DdcBuf, (TRUE));
+        }
+    return XST_SUCCESS;
+    }
+    return XST_FAILURE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function detects connected sink is a HDMI 2.0/HDMI 1.4 sink device
+* and sets appropriate flag in the TX stream.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - XST_SUCCESS if HDMI 2.0
+*       - XST_FAILURE if HDMI 1.4
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_DetectHdmi20(XV_HdmiTx *InstancePtr)
+{
+    u8 DdcBuf[2];
+    u32 Status;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    /* Write source version. Offset (Source version) */
+    DdcBuf[0] = 0x02;
+
+    /* Version 1 */
+    DdcBuf[1] = 0x01;
+    Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 2, (u8*)&DdcBuf, (TRUE));
+
+    /* If the write was successful, then the sink is HDMI 2.0 */
+    if (Status == (XST_SUCCESS)) {
+        InstancePtr->Stream.IsHdmi20 = (TRUE);
+        Status = (XST_SUCCESS);
+    }
+
+    /* Else it is a HDMI 1.4 device */
+    else {
+        InstancePtr->Stream.IsHdmi20 = (FALSE);
+        Status = (XST_FAILURE);
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function shows the sinks SCDC registers.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_ShowSCDC(XV_HdmiTx *InstancePtr)
+{
+    u8 DdcBuf[2];
+    u32 Status;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Sink version. Offset Scrambler status */
+    DdcBuf[0] = 0x01;
+    Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (FALSE));
+
+    /* Check if write was successful */
+    if (Status == (XST_SUCCESS)) {
+        Status = XV_HdmiTx_DdcRead(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (TRUE));
+        xil_printf("HDMI TX: SCDC 0x01 : %0x\r\n", DdcBuf[0]);
+    }
+
+    /* TMDS configuration. Offset Scrambler status */
+    DdcBuf[0] = 0x20;
+    Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (FALSE));
+
+    /* Check if write was successful */
+    if (Status == (XST_SUCCESS)) {
+        Status = XV_HdmiTx_DdcRead(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (TRUE));
+        xil_printf("HDMI TX: SCDC 0x20 : %0x\r\n", DdcBuf[0]);
+    }
+
+    /* Scrambler status. Offset Scrambler status */
+    DdcBuf[0] = 0x21;
+    Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (FALSE));
+
+    /* Check if write was successful */
+    if (Status == (XST_SUCCESS)) {
+        Status = XV_HdmiTx_DdcRead(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (TRUE));
+        xil_printf("HDMI TX: SCDC 0x21 : %0x\r\n", DdcBuf[0]);
+    }
+
+    /* Status flags. Offset Scrambler status */
+    DdcBuf[0] = 0x40;
+    Status = XV_HdmiTx_DdcWrite(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (FALSE));
+
+    /* Check if write was successful */
+    if (Status == (XST_SUCCESS)) {
+        Status = XV_HdmiTx_DdcRead(InstancePtr, 0x54, 1, (u8*)&DdcBuf, (TRUE));
+        xil_printf("HDMI TX: SCDC 0x40 : %0x\r\n", DdcBuf[0]);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the HDMI TX stream parameters.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    VideoMode specifies resolution identifier.
+* @param    ColorFormat specifies the type of color format.
+*       - 0 = XVIDC_CSF_RGB
+*       - 1 = XVIDC_CSF_YCRCB_444
+*       - 2 = XVIDC_CSF_YCRCB_422
+*       - 3 = XVIDC_CSF_YCRCB_420
+* @param    Bpc specifies the color depth/bits per color component.
+*       - 6 = XVIDC_BPC_6
+*       - 8 = XVIDC_BPC_8
+*       - 10 = XVIDC_BPC_10
+*       - 12 = XVIDC_BPC_12
+*       - 16 = XVIDC_BPC_16
+* @param    Ppc specifies the pixel per clock.
+*       - 1 = XVIDC_PPC_1
+*       - 2 = XVIDC_PPC_2
+*       - 4 = XVIDC_PPC_4
+*
+* @return   TmdsClock, reference clock calculated based on the input
+*       parameters.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiTx_SetStream(XV_HdmiTx *InstancePtr, XVidC_VideoMode VideoMode,
+XVidC_ColorFormat ColorFormat, XVidC_ColorDepth Bpc, XVidC_PixelsPerClock Ppc,
+XVidC_3DInfo *Info3D)
+{
+    u32 TmdsClock;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid((ColorFormat == (XVIDC_CSF_RGB))       ||
+                      (ColorFormat == (XVIDC_CSF_YCRCB_444)) ||
+                      (ColorFormat == (XVIDC_CSF_YCRCB_422)) ||
+                      (ColorFormat == (XVIDC_CSF_YCRCB_420)));
+    Xil_AssertNonvoid((Bpc == (XVIDC_BPC_8))  ||
+                      (Bpc == (XVIDC_BPC_10)) ||
+                      (Bpc == (XVIDC_BPC_12)) ||
+                      (Bpc == (XVIDC_BPC_16)));
+    Xil_AssertNonvoid((Ppc == (XVIDC_PPC_1)) ||
+                      (Ppc == (XVIDC_PPC_2)) ||
+                      (Ppc == (XVIDC_PPC_4)));
+
+    if(Info3D == NULL)
+        XVidC_SetVideoStream(&InstancePtr->Stream.Video, VideoMode, ColorFormat, Bpc, Ppc);
+    else
+        XVidC_Set3DVideoStream(&InstancePtr->Stream.Video, VideoMode, ColorFormat, Bpc, Ppc, Info3D);
+
+    /** In HDMI the colordepth in YUV422 is always 12 bits,
+    * although on the link itself it is being transmitted as 8-bits.
+    * Therefore if the colorspace is YUV422, then force the colordepth
+    * to 12 bits. */
+    if (ColorFormat == XVIDC_CSF_YCRCB_422) {
+        InstancePtr->Stream.Video.ColorDepth = XVIDC_BPC_12;
+    }
+
+    InstancePtr->Stream.Vic = XV_HdmiTx_LookupVic(
+        InstancePtr->Stream.Video.VmId);
+
+    // Set TX pixel rate
+    XV_HdmiTx_SetPixelRate(InstancePtr);
+
+    // Set TX color space
+    XV_HdmiTx_SetColorFormat(InstancePtr);
+
+    // Set TX color depth
+    XV_HdmiTx_SetColorDepth(InstancePtr);
+
+    /* Calculate reference clock. First calculate the pixel clock */
+    TmdsClock = XV_HdmiTx_GetTmdsClk(InstancePtr,
+                                     InstancePtr->Stream.Video.VmId,
+                                     ColorFormat,
+                                     Bpc);
+
+    /* Store TMDS clock for future reference */
+	InstancePtr->Stream.TMDSClock = TmdsClock;
+
+    /* HDMI 2.0 */
+    if (InstancePtr->Stream.IsHdmi20 && TmdsClock > 340000000) {
+            InstancePtr->Stream.IsScrambled = (TRUE);
+            InstancePtr->Stream.TMDSClockRatio  = 1;
+    }
+    /* HDMI 1.4 */
+    else {
+		InstancePtr->Stream.IsScrambled = (FALSE);
+        InstancePtr->Stream.TMDSClockRatio  = 0;
+    }
+
+    XV_HdmiTx_Scrambler(InstancePtr);
+    XV_HdmiTx_ClockRatio(InstancePtr);
+
+    if ((InstancePtr->Stream.IsHdmi20 == (FALSE)) && (TmdsClock > 340000000)) {
+        TmdsClock = 0;
+    }
+
+    return TmdsClock;
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI TX Internal VRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI TX Internal VRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI TX. Therefore, clearing the PIO reset output will assert
+*       the HDMI Internal video reset.
+*       C-style signature:
+*       void XV_HdmiTx_INT_VRST(XV_HdmiTx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiTx_INT_VRST(XV_HdmiTx *InstancePtr, u8 Reset)
+{
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_INT_VRST_MASK));
+    }
+    else {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_INT_VRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI TX Internal LRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI TX Internal LRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI TX. Therefore, clearing the PIO reset output will assert
+*       the HDMI Internal link reset.
+*       C-style signature:
+*       void XV_HdmiTx_INT_VRST(XV_HdmiTx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiTx_INT_LRST(XV_HdmiTx *InstancePtr, u8 Reset)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_INT_LRST_MASK));
+    }
+    else {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_INT_LRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI TX External VRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI TX External VRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI TX. Therefore, clearing the PIO reset output will assert
+*       the HDMI external video reset.
+*       C-style signature:
+*       void XV_HdmiTx_EXT_VRST(XV_HdmiTx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiTx_EXT_VRST(XV_HdmiTx *InstancePtr, u8 Reset)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_EXT_VRST_MASK));
+    }
+    else {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_EXT_VRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function asserts or releases the HDMI TX External SYSRST.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI TX External SYSRST.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI TX. Therefore, clearing the PIO reset output will assert
+*       the HDMI External system reset.
+*       C-style signature:
+*       void XV_HdmiTx_EXT_SYSRST(XV_HdmiTx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+void XV_HdmiTx_EXT_SYSRST(XV_HdmiTx *InstancePtr, u8 Reset)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    if (Reset) {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_EXT_SYSRST_MASK));
+    }
+    else {
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_EXT_SYSRST_MASK));
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function sets the HDMI TX AUX GCP register AVMUTE bit.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_SetGcpAvmuteBit(XV_HdmiTx *InstancePtr)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_GCP_AVMUTE_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function clears the HDMI TX AUX GCP register AVMUTE bit.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_ClearGcpAvmuteBit(XV_HdmiTx *InstancePtr)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_GCP_AVMUTE_MASK));
+
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function sets the HDMI TX AUX GCP register CLEAR_AVMUTE bit.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_SetGcpClearAvmuteBit(XV_HdmiTx *InstancePtr)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_GCP_CLEARAVMUTE_MASK));
+}
+
+/*****************************************************************************/
+/**
+*
+*  This function clears the HDMI TX AUX GCP register CLEAR_AVMUTE bit.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_ClearGcpClearAvmuteBit(XV_HdmiTx *InstancePtr)
+{
+	/* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_GCP_CLEARAVMUTE_MASK));
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the pixel rate at output.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_SetPixelRate(XV_HdmiTx *InstancePtr)
+{
+    u32 RegValue;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Mask PIO Out Mask register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_MSK_OFFSET),
+        (XV_HDMITX_PIO_OUT_PIXEL_RATE_MASK));
+
+    /* Check for pixel width */
+    switch (InstancePtr->Stream.Video.PixPerClk) {
+
+        case (XVIDC_PPC_2):
+            RegValue = 1;
+            break;
+
+        case (XVIDC_PPC_4):
+            RegValue = 2;
+            break;
+
+        default:
+            RegValue = 0;
+            break;
+    }
+
+    /* Write pixel rate into PIO Out register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_OFFSET),
+        (RegValue << (XV_HDMITX_PIO_OUT_PIXEL_RATE_SHIFT)));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the sample rate at output.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    SampleRate specifies the value that needs to be set.
+*       - 2 samples per clock
+*       - 3 samples per clock.
+*       - 5 samples per clock.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_SetSampleRate(XV_HdmiTx *InstancePtr, u8 SampleRate)
+{
+    u32 RegValue;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(SampleRate < 0xFF);
+
+    // Store sample rate in structure
+    InstancePtr->Stream.SampleRate = SampleRate;
+
+    // Mask PIO Out Mask register
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_MSK_OFFSET),
+        (XV_HDMITX_PIO_OUT_SAMPLE_RATE_MASK));
+
+    // Check for sample rate
+    switch (SampleRate) {
+        case 2:
+            RegValue = 2;
+            break;
+
+        case 3:
+            RegValue = 1;
+            break;
+
+        case 5:
+            RegValue = 3;
+            break;
+
+        default:
+            RegValue = 0;
+            break;
+    }
+
+    // Write sample rate into PIO Out register
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_OFFSET),
+        (RegValue << (XV_HDMITX_PIO_OUT_SAMPLE_RATE_SHIFT)));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the color format
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_SetColorFormat(XV_HdmiTx *InstancePtr)
+{
+    u32 RegValue;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Mask PIO Out Mask register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_MSK_OFFSET),
+        (XV_HDMITX_PIO_OUT_COLOR_SPACE_MASK));
+
+    /* Check for color format */
+    switch (InstancePtr->Stream.Video.ColorFormatId) {
+        case (XVIDC_CSF_YCRCB_444):
+            RegValue = 1;
+            break;
+
+        case (XVIDC_CSF_YCRCB_422):
+            RegValue = 2;
+            break;
+
+        case (XVIDC_CSF_YCRCB_420):
+            RegValue = 3;
+            break;
+
+        default:
+            RegValue = 0;
+            break;
+    }
+
+    /* Write color space into PIO Out register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_OFFSET),
+        (RegValue << (XV_HDMITX_PIO_OUT_COLOR_SPACE_SHIFT)));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the color depth
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_SetColorDepth(XV_HdmiTx *InstancePtr)
+{
+    u32 RegValue;
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Mask PIO Out Mask register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_MSK_OFFSET), (XV_HDMITX_PIO_OUT_COLOR_DEPTH_MASK));
+
+    // Color depth
+    switch (InstancePtr->Stream.Video.ColorDepth) {
+        // 10 bits
+        case (XVIDC_BPC_10):
+            RegValue = 1;
+            break;
+
+        // 12 bits
+        case (XVIDC_BPC_12):
+            RegValue = 2;
+            break;
+
+        // 16 bits
+        case (XVIDC_BPC_16):
+            RegValue = 3;
+            break;
+
+        // 8 bits
+        default:
+            RegValue = 0;
+            break;
+    }
+
+    /* Write color depth into PIO Out register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_PIO_OUT_OFFSET),
+        (RegValue << (XV_HDMITX_PIO_OUT_COLOR_DEPTH_SHIFT)));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prepares TX DDC peripheral to use.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Frequency specifies the value that needs to be set.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_DdcInit(XV_HdmiTx *InstancePtr, u32 Frequency)
+{
+    u32 RegValue;
+
+    /* Verify arguments. */
+    Xil_AssertVoid(InstancePtr != NULL);
+    Xil_AssertVoid(Frequency > 0x0);
+
+    RegValue = (Frequency / 100000) / 2;
+    RegValue = ((RegValue) << (XV_HDMITX_DDC_CTRL_CLK_DIV_SHIFT)) &
+     ((XV_HDMITX_DDC_CTRL_CLK_DIV_MASK) << (XV_HDMITX_DDC_CTRL_CLK_DIV_SHIFT));
+
+    /* Update DDC Control register */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_DDC_CTRL_OFFSET), RegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the acknowledge flag
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @note     None.
+*
+******************************************************************************/
+static int XV_HdmiTx_DdcGetAck(XV_HdmiTx *InstancePtr)
+{
+    u32 Status;
+
+    // Read status register
+    Status = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_DDC_STA_OFFSET));
+    return (Status & XV_HDMITX_DDC_STA_ACK_MASK);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function waits for the done flag to be set
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @note     None.
+*
+******************************************************************************/
+static int XV_HdmiTx_DdcWaitForDone(XV_HdmiTx *InstancePtr)
+{
+    u32 Data;
+    u32 Status;
+    u32 Exit;
+
+    Exit = (FALSE);
+
+    // Default status, assume failure
+    Status = XST_FAILURE;
+
+    do {
+        // Read control register
+        Data = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+            (XV_HDMITX_DDC_CTRL_OFFSET));
+
+        if (Data & (XV_HDMITX_DDC_CTRL_RUN_MASK)) {
+
+            // Read status register
+            Data = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+                (XV_HDMITX_DDC_STA_OFFSET));
+
+            // Done
+            if (Data & (XV_HDMITX_DDC_STA_DONE_MASK)) {
+                // Clear done flag
+                XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+                    (XV_HDMITX_DDC_STA_OFFSET), (XV_HDMITX_DDC_STA_DONE_MASK));
+                Exit = (TRUE);
+                Status = XST_SUCCESS;
+            }
+
+            // Time out
+            else if (Data & (XV_HDMITX_DDC_STA_TIMEOUT_MASK)) {
+                // Clear time out flag
+                XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+                    (XV_HDMITX_DDC_STA_OFFSET), (XV_HDMITX_DDC_STA_TIMEOUT_MASK));
+                Exit = (TRUE);
+                Status = XST_FAILURE;
+            }
+        }
+        else {
+            Status = (XST_FAILURE);
+            Exit = (TRUE);
+        }
+
+    } while (!Exit);
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function writes data into the command fifo.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @note     None.
+*
+******************************************************************************/
+static u32 XV_HdmiTx_DdcWriteCommand(XV_HdmiTx *InstancePtr, u32 Cmd)
+{
+    u32 Status;
+    u32 Exit;
+	int Tries = 0;
+	
+    Exit = (FALSE);
+
+    do {
+        // Read control register
+        Status = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+					(XV_HDMITX_DDC_CTRL_OFFSET));
+
+        if (Status & (XV_HDMITX_DDC_CTRL_RUN_MASK)) {
+            // Read status register
+            Status = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+						(XV_HDMITX_DDC_STA_OFFSET));
+
+            // Mask command fifo full flag
+            Status &= XV_HDMITX_DDC_STA_CMD_FULL;
+
+            // Check if the command fifo isn't full
+			/* TODO - Not same as BM code */
+            if (!Status) {
+                XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+                    (XV_HDMITX_DDC_CMD_OFFSET), (Cmd));
+				Status = XST_SUCCESS;
+                Exit = (TRUE);
+            } else {
+			  /* FIFO Full Case */
+			  usleep_range(100, 200);
+			  /* FIFO remained full for 1 millisecond (10 iterations of at least 100 microseconds). */
+			  if (Tries++ > 10) {
+				// Disable DDC peripheral
+				XV_HdmiTx_DdcDisable(InstancePtr);
+			    Status = XST_FAILURE;
+				Exit = (TRUE);
+			  }
+			}
+        }
+        else {
+            Status = (XST_FAILURE);
+            Exit = (TRUE);
+        }
+    } while (!Exit);
+	return(Status);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads data from the data fifo.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @note     None.
+*
+******************************************************************************/
+static u8 XV_HdmiTx_DdcReadData(XV_HdmiTx *InstancePtr)
+{
+    u32 Status;
+    u32 Exit;
+    u32 Data;
+	int Tries = 0;
+
+    Exit = (FALSE);
+
+    do {
+        // Read control register
+        Data = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+            (XV_HDMITX_DDC_CTRL_OFFSET));
+
+        if (Data & (XV_HDMITX_DDC_CTRL_RUN_MASK)) {
+            // Read status register
+            Status = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+                (XV_HDMITX_DDC_STA_OFFSET));
+
+            // Mask data fifo empty flag
+            Status &= XV_HDMITX_DDC_STA_DAT_EMPTY;
+
+            // Check if the data fifo has data
+			/* TODO - Not same as BM code */
+            if (!Status) {
+                Data = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+                    (XV_HDMITX_DDC_DAT_OFFSET));
+                Exit = (TRUE);
+            } else {
+			  /* FIFO Full Case - allow time for slave clock stretching */
+			  usleep_range(1000, 1100);
+			  /* FIFO remained full for 10 millisecond (10 iterations of at least 1msec). */
+			  if (Tries++ > 10) {
+				// Disable DDC peripheral
+				XV_HdmiTx_DdcDisable(InstancePtr);
+				Exit = (TRUE);
+				Data = 0;				
+			  }
+			}
+        }
+        else {
+            Exit = (TRUE);
+            Data = 0;
+        }
+    } while (!Exit);
+
+    return (Data);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function writes data from DDC peripheral from given slave address.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Slave specifies the slave address from where data needs to be
+*       read.
+* @param    Length specifies number of bytes to be read.
+* @param    Buffer specifies a pointer to u8 variable that will be
+*       filled with data.
+* @param    Stop specifies the stop flag which is either TRUE/FALSE.
+*
+* @return
+*       - XST_SUCCESS if an acknowledgement received and timeout.
+*       - XST_FAILURE if no acknowledgement received.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_DdcWrite(XV_HdmiTx *InstancePtr, u8 Slave,
+    u16 Length, u8 *Buffer, u8 Stop)
+{
+    u32 Status;
+    u32 Data;
+    u32 Index;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(Slave > 0x0);
+    Xil_AssertNonvoid(Length > 0x0);
+    Xil_AssertNonvoid(Buffer != NULL);
+    Xil_AssertNonvoid((Stop == (TRUE)) || (Stop == (FALSE)));
+
+    /* [DIFF FROM BM] Not taking this BM logic as we disable PIO interrupts in the handler and
+     * enabling it when interrupt is processed.
+     */
+#if 0
+    /* Disable PIO Interrupt to prevent another DDC transactions from happening
+     * in the middle of an ongoing DDC transaction
+     */
+    XV_HdmiTx_PioIntrDisable(InstancePtr);
+#endif
+
+    // Status default, assume failure
+    Status = XST_FAILURE;
+
+    // Enable DDC peripheral
+    XV_HdmiTx_DdcEnable(InstancePtr);
+
+    // Disable interrupt in DDC peripheral
+    // Polling is used
+    XV_HdmiTx_DdcIntrDisable(InstancePtr);
+
+    // Write start token
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (XV_HDMITX_DDC_CMD_STR_TOKEN));
+	if (Status == XST_FAILURE) return(Status);
+	
+    // First check if the slave can be addressed
+    // Write write token
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (XV_HDMITX_DDC_CMD_WR_TOKEN));
+	if (Status == XST_FAILURE) return(Status);
+
+    // Write length (high)
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, 0);
+	if (Status == XST_FAILURE) return(Status);
+
+    // Write length (low)
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, 1);
+	if (Status == XST_FAILURE) return(Status);
+
+    // Slave address
+    Data = Slave << 1;
+
+    // Set write bit (low)
+    Data &= 0xFE;
+
+    // Write slave address
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (Data));
+	if (Status == XST_FAILURE) return(Status);
+
+    // Wait for done flag
+    if (XV_HdmiTx_DdcWaitForDone(InstancePtr) == XST_SUCCESS) {
+
+        // Check acknowledge
+        if (XV_HdmiTx_DdcGetAck(InstancePtr)) {
+
+            // Now write the data
+            // Write write token
+            Status = XV_HdmiTx_DdcWriteCommand(InstancePtr,
+						(XV_HDMITX_DDC_CMD_WR_TOKEN));
+			if (Status == XST_FAILURE) return(Status);
+
+            // Write length (high)
+            Data = ((Length >> 8) & 0xFF);
+            Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, Data);
+			if (Status == XST_FAILURE) return(Status);
+
+            // Write length (low)
+            Data = (Length & 0xFF);
+            Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, Data);
+			if (Status == XST_FAILURE) return(Status);
+
+            // Write Data
+            for (Index = 0; Index < Length; Index++) {
+                Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, *Buffer++);
+				if (Status == XST_FAILURE) return(Status);
+            }
+
+            // Wait for done flag
+            if (XV_HdmiTx_DdcWaitForDone(InstancePtr) == XST_SUCCESS) {
+
+                // Check acknowledge
+                // ACK
+                if (XV_HdmiTx_DdcGetAck(InstancePtr)) {
+
+                    // Stop condition
+                    if (Stop) {
+                        // Write stop token
+                        Status = XV_HdmiTx_DdcWriteCommand(InstancePtr,
+									(XV_HDMITX_DDC_CMD_STP_TOKEN));
+						if (Status == XST_FAILURE) return(Status);
+
+                        // Wait for done flag
+                        XV_HdmiTx_DdcWaitForDone(InstancePtr);
+                    }
+
+					// Update status flag
+					Status = XST_SUCCESS;
+                }
+            }
+        }
+    }
+
+    // Disable DDC peripheral
+    XV_HdmiTx_DdcDisable(InstancePtr);
+
+    /* [DIFF FROM BM] Not taking this BM logic as we disable PIO interrupts in the handler and
+     * enabling it when interrupt is processed.
+     */
+#if 0
+    // Enable the interrupts which were disabled earlier
+    XV_HdmiTx_PioIntrEnable(InstancePtr);
+#endif
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads data from DDC peripheral from given slave address.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Slave specifies the slave address from where data needs to be
+*       read.
+* @param    Length specifies number of bytes to be read.
+* @param    Buffer specifies a pointer to u8 variable that will be
+*       filled with data.
+* @param    Stop specifies the stop flag which is either TRUE/FALSE.
+*
+* @return
+*       - XST_SUCCESS if an acknowledgement received and timeout.
+*       - XST_FAILURE if no acknowledgement received.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_DdcRead(XV_HdmiTx *InstancePtr, u8 Slave, u16 Length,
+    u8 *Buffer, u8 Stop)
+{
+    u32 Status;
+    u32 Data;
+    u32 Index;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(Slave > 0x0);
+    Xil_AssertNonvoid(Length > 0x0);
+    Xil_AssertNonvoid(Buffer != NULL);
+    Xil_AssertNonvoid((Stop == (TRUE)) || (Stop == (FALSE)));
+
+    /* [DIFF FROM BM] Not taking this BM logic as we disable PIO interrupts in the handler and
+     * enabling it when interrupt is processed.
+     */
+#if 0
+    /* Disable PIO Interrupt to prevent another DDC transactions from happening
+     * in the middle of an ongoing DDC transaction
+     */
+    XV_HdmiTx_PioIntrDisable(InstancePtr);
+#endif
+
+    // Status default, assume failure
+    Status = XST_FAILURE;
+
+    // Enable DDC peripheral
+    XV_HdmiTx_DdcEnable(InstancePtr);
+
+    // Disable interrupt in DDC peripheral
+    // Polling is used
+    XV_HdmiTx_DdcIntrDisable(InstancePtr);
+
+    // Write start token
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (XV_HDMITX_DDC_CMD_STR_TOKEN));
+	if (Status == XST_FAILURE) return(Status);
+	
+    // First check if the slave can be addressed
+    // Write write token
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (XV_HDMITX_DDC_CMD_WR_TOKEN));
+	if (Status == XST_FAILURE) return(Status);
+	
+    // Write length (high)
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, 0);
+	if (Status == XST_FAILURE) return(Status);
+	
+    // Write length (low)
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, 1);
+	if (Status == XST_FAILURE) return(Status);
+	
+    // Slave address
+    Data = Slave << 1;
+
+    // Set read bit (high)
+    Data |= 0x01;
+
+    // Write slave address
+    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (Data));
+	if (Status == XST_FAILURE) return(Status);
+	
+    // Wait for done flag
+    if (XV_HdmiTx_DdcWaitForDone(InstancePtr) == XST_SUCCESS) {
+
+        // Check acknowledge
+        if (XV_HdmiTx_DdcGetAck(InstancePtr)) {
+
+            // Write read token
+            Status = XV_HdmiTx_DdcWriteCommand(InstancePtr,
+						(XV_HDMITX_DDC_CMD_RD_TOKEN));
+			if (Status == XST_FAILURE) return(Status);
+			
+            // Write read length (high)
+            Data = (Length >> 8) & 0xFF;
+            Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (Data));
+			if (Status == XST_FAILURE) return(Status);
+			
+            // Write read length (low)
+            Data = Length & 0xFF;
+            Status = XV_HdmiTx_DdcWriteCommand(InstancePtr, (Data));
+			if (Status == XST_FAILURE) return(Status);
+			
+            // Read Data
+            for (Index = 0; Index < Length; Index++) {
+                *Buffer++ = XV_HdmiTx_DdcReadData(InstancePtr);
+            }
+
+            // Wait for done flag
+            if (XV_HdmiTx_DdcWaitForDone(InstancePtr) == XST_SUCCESS) {
+
+                // Stop condition
+                if (Stop) {
+                    // Write stop token
+                    Status = XV_HdmiTx_DdcWriteCommand(InstancePtr,
+								(XV_HDMITX_DDC_CMD_STP_TOKEN));
+					if (Status == XST_FAILURE) return(Status);
+					
+                    // Wait for done flag
+                    XV_HdmiTx_DdcWaitForDone(InstancePtr);
+                }
+
+                // Update status
+                Status = XST_SUCCESS;
+            }
+        }
+    }
+
+    // Disable DDC peripheral
+    XV_HdmiTx_DdcDisable(InstancePtr);
+
+    /* [DIFF FROM BM] Not taking this BM logic as we disable PIO interrupts in the handler and
+     * enabling it when interrupt is processed.
+     */
+#if 0
+    // Enable the interrupts which were disabled earlier
+    XV_HdmiTx_PioIntrEnable(InstancePtr);
+#endif
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function transmits the infoframes generated by the processor.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - XST_SUCCESS if infoframes transmitted successfully.
+*       - XST_FAILURE if AUX FIFO is full.
+*
+* @note     None.
+*
+******************************************************************************/
+u32 XV_HdmiTx_AuxSend(XV_HdmiTx *InstancePtr)
+{
+    u32 Index;
+    u32 Status;
+    u32 RegValue;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    // Default
+	Status = (XST_FAILURE);
+
+    /* Read the AUX status register */
+    RegValue = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+        (XV_HDMITX_AUX_STA_OFFSET));
+
+    // First check if the AUX packet is ready
+    if (RegValue & (XV_HDMITX_AUX_STA_PKT_RDY_MASK)) {
+
+	// Check if the fifo is full
+		if (RegValue & (XV_HDMITX_AUX_STA_FIFO_FUL_MASK)) {
+			RegValue = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+			        (XV_HDMITX_AUX_STA_OFFSET));
+
+			xdbg_printf((XDBG_DEBUG_GENERAL), "HDMI TX AUX FIFO full\r\n");
+		}
+		else {
+			/* Update AUX with header data */
+			XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+				(XV_HDMITX_AUX_DAT_OFFSET), InstancePtr->Aux.Header.Data);
+
+			/* Update AUX with actual data */
+			for (Index = 0x0; Index < 8; Index++) {
+				XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+					(XV_HDMITX_AUX_DAT_OFFSET), InstancePtr->Aux.Data.Data[Index]);
+			}
+
+			Status = (XST_SUCCESS);
+		}
+    }
+    return Status;
+}
+
+/******************************************************************************/
+/**
+*
+* This function prints stream and timing information on STDIO/Uart console.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_DebugInfo(XV_HdmiTx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertVoid(InstancePtr != NULL);
+
+    /* Print stream information */
+    XVidC_ReportStreamInfo(&InstancePtr->Stream.Video);
+
+    /* Print timing information */
+    XVidC_ReportTiming(&InstancePtr->Stream.Video.Timing,
+                InstancePtr->Stream.Video.IsInterlaced);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides status of the stream
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - TRUE = Scrambled.
+*       - FALSE = Not scrambled.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_IsStreamScrambled(XV_HdmiTx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    return (InstancePtr->Stream.IsScrambled);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function provides the stream connected status
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - TRUE = Stream is connected.
+*       - FALSE = Stream is connected.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_IsStreamConnected(XV_HdmiTx *InstancePtr)
+{
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    return (InstancePtr->Stream.IsConnected);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the active audio channels
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - XST_SUCCESS if active channels were set.
+*       - XST_FAILURE if no active channles were set.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_SetAudioChannels(XV_HdmiTx *InstancePtr, u8 Value)
+{
+    u32 Data;
+    u32 Status;
+    u8 AudioStatus;
+    u32 AudioCtrl;
+
+    AudioCtrl = XV_HdmiTx_ReadReg((InstancePtr)->Config.BaseAddress,
+			XV_HDMITX_AUD_CTRL_OFFSET);
+
+    AudioStatus = AudioCtrl & XV_HDMITX_AUD_CTRL_RUN_MASK;
+
+    // Stop peripheral
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_AUD_CTRL_CLR_OFFSET), (XV_HDMITX_AUD_CTRL_RUN_MASK));
+    AudioCtrl &= ~((u32)XV_HDMITX_AUD_CTRL_RUN_MASK);
+
+    switch (Value) {
+	// 32 Channels
+	case 32:
+            Data = 6;
+            Status = (XST_SUCCESS);
+            break;
+
+	// 24 Channels
+	case 24:
+            Data = 5;
+            Status = (XST_SUCCESS);
+            break;
+
+	// 12 Channels
+	case 12:
+            Data = 4;
+            Status = (XST_SUCCESS);
+            break;
+
+        // 8 Channels
+        case 8:
+            Data = 3;
+            Status = (XST_SUCCESS);
+            break;
+
+        // 6 Channels
+        case 6:
+            Data = 2;
+            Status = (XST_SUCCESS);
+            break;
+
+        // 4 Channels
+        case 4:
+            Data = 1;
+            Status = (XST_SUCCESS);
+            break;
+
+        // 2 Channels
+        case 2:
+            Data = 0;
+            Status = (XST_SUCCESS);
+            break;
+
+        default :
+            Status = (XST_FAILURE);
+            break;
+    }
+
+    if (Status == (XST_SUCCESS)) {
+	Data &= XV_HDMITX_AUD_CTRL_CH_MASK;
+        Data <<= XV_HDMITX_AUD_CTRL_CH_SHIFT;
+
+        AudioCtrl &= ~((u32)(XV_HDMITX_AUD_CTRL_CH_MASK <<
+			XV_HDMITX_AUD_CTRL_CH_SHIFT));
+        AudioCtrl |= Data;
+
+        // Set active channels
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+            (XV_HDMITX_AUD_CTRL_OFFSET), (AudioCtrl));
+
+        // Store active channel in structure
+        (InstancePtr)->Stream.Audio.Channels = Value;
+
+        // Start peripheral
+        if (AudioStatus) {
+			XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+					(XV_HDMITX_AUD_CTRL_SET_OFFSET),
+					(XV_HDMITX_AUD_CTRL_RUN_MASK));
+        }
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets the active audio format
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return
+*       - XST_SUCCESS if active channels were set.
+*       - XST_FAILURE if no active channles were set.
+*
+* @note     None.
+*
+******************************************************************************/
+int XV_HdmiTx_SetAudioFormat(XV_HdmiTx *InstancePtr, XV_HdmiTx_AudioFormatType Value)
+{
+    u32 Status;
+    u32 AudioCtrl;
+    u32 Data;
+
+    if (Value > XV_HDMITX_AUDFMT_3D) {
+	    return XST_FAILURE;
+    }
+
+    Data = Value;
+
+    // Stop peripheral
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+        (XV_HDMITX_AUD_CTRL_CLR_OFFSET), (XV_HDMITX_AUD_CTRL_RUN_MASK));
+
+    AudioCtrl = XV_HdmiTx_ReadReg((InstancePtr)->Config.BaseAddress,
+		    XV_HDMITX_AUD_CTRL_OFFSET);
+
+    Data &= XV_HDMITX_AUD_CTRL_AUDFMT_MASK;
+    Data <<= XV_HDMITX_AUD_CTRL_AUDFMT_SHIFT;
+
+    AudioCtrl &= ~((u32)(XV_HDMITX_AUD_CTRL_AUDFMT_MASK <<
+			XV_HDMITX_AUD_CTRL_AUDFMT_SHIFT));
+    AudioCtrl |= Data;
+
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+                (XV_HDMITX_AUD_CTRL_OFFSET), (AudioCtrl));
+
+    // Start peripheral
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress,
+		    (XV_HDMITX_AUD_CTRL_SET_OFFSET),
+		    (XV_HDMITX_AUD_CTRL_RUN_MASK));
+
+    Status = (XST_SUCCESS);
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the active audio format
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   Active audio format of HDMI Tx
+*
+* @note     None.
+*
+******************************************************************************/
+XV_HdmiTx_AudioFormatType XV_HdmiTx_GetAudioFormat(XV_HdmiTx *InstancePtr)
+{
+	XV_HdmiTx_AudioFormatType RegValue;
+
+    Xil_AssertNonvoid(InstancePtr != NULL);
+
+    RegValue = XV_HdmiTx_ReadReg((InstancePtr)->Config.BaseAddress, (XV_HDMITX_AUD_CTRL_OFFSET));
+    RegValue = (RegValue >> XV_HDMITX_AUD_CTRL_AUDFMT_SHIFT) & (XV_HDMITX_AUD_CTRL_AUDFMT_MASK);
+
+    return RegValue;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is a stub for the asynchronous callback. The stub is here in
+* case the upper layer forgot to set the handlers. On initialization, all
+* handlers are set to this callback. It is considered an error for this
+* handler to be invoked.
+*
+* @param    CallbackRef is a callback reference passed in by the upper
+*       layer when setting the callback functions, and passed back to
+*       the upper layer when the callback is invoked.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+static void StubCallback(void *Callback)
+{
+    Xil_AssertVoid(Callback != NULL);
+    Xil_AssertVoidAlways();
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx.h
@@ -0,0 +1,1130 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitx.h
+*
+* This is the main header file for Xilinx HDMI TX core. HDMI TX core is used
+* for transmitting the incoming video and audio streams. It consists of
+* - Transmitter core
+* - AXI4-Stream to Video Bridge
+* - Video Timing Controller and
+* - High-bandwidth Digital Content Protection (HDCP) (Optional).
+*
+* The HDMI TX uses three AXI interfaces for Video, Audio and Processor:
+* - AXI4-Stream interface for Video, can be single, dual or quad pixels per
+* clock and supports 8 and 10 bits per component.
+* - AXI4-Stream interface for Audio, accepts multiple channels uncompressed
+* and compressed audio data.
+* - AXI4-Lite interface for processor, controls the transmitter.
+* Please do refer AXI Reference Guide (UG761) for more information on AXI
+* interfaces.
+*
+* Transmitter core performs following operations:
+* - Converts video data from the video clock domain into the link clock domain.
+* - TMDS (Transition Minimized Differential Signaling) encoding.
+* - Merges encoded video data and packet data into a single HDMI stream.
+* - Optional HDMI stream is encrypted by an external HDCP module.
+* - Over samples HDMI stream if stream bandwidth is too low for the transceiver
+* to handle.
+* - Scrambles encrypted/HDMI stream if data rate is above 3.4 Gbps otherwise
+* bypasses the Scrambler.
+*
+* AXI Video Bridge converts the incoming video AXI-stream to native video.
+*
+* Video Timing Controller (VTC) generates the native video timing.
+*
+* <b>Core Features </b>
+*
+* For a full description of HDMI TX features, please see the hardware
+* specification.
+*
+* <b>Software Initialization & Configuration</b>
+*
+* The application needs to do following steps in order for preparing the
+* HDMI TX core to be ready.
+*
+* - Call XV_HdmiTx_LookupConfig using a device ID to find the core
+*   configuration.
+* - Call XV_HdmiTx_CfgInitialize to initialize the device and the driver
+*   instance associated with it.
+*
+* <b>Interrupts </b>
+*
+* This driver provides interrupt handlers
+* - XV_HdmiTx_IntrHandler, for handling the interrupts from the HDMI TX core
+* PIO and DDC peripheral respectively.
+*
+* Application developer needs to register interrupt handler with the processor,
+* within their examples. Whenever processor calls registered application's
+* interrupt handler associated with interrupt id, application's interrupt
+* handler needs to call appropriate peripheral interrupt handler reading
+* peripheral's Status register.
+
+* This driver provides XV_HdmiTx_SetCallback API to register functions with HDMI
+* TX core instance.
+*
+* <b> Virtual Memory </b>
+*
+* This driver supports Virtual Memory. The RTOS is responsible for calculating
+* the correct device base address in Virtual Memory space.
+*
+* <b> Threads </b>
+*
+* This driver is not thread safe. Any needs for threads or thread mutual
+* exclusion must be satisfied by the layer above this driver.
+*
+* <b> Asserts </b>
+*
+* Asserts are used within all Xilinx drivers to enforce constraints on argument
+* values. Asserts can be turned off on a system-wide basis by defining at
+* compile time, the NDEBUG identifier. By default, asserts are turned on and it
+* is recommended that users leave asserts on during development.
+*
+* <b> Building the driver </b>
+*
+* The HDMI TX driver is composed of several source files. This allows the user
+* to build and link only those parts of the driver that are necessary.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*s
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     15/01/16 Add 3D Support
+* 1.2   MG     09/03/16 Added XV_HdmiTx_SetHdmiMode and XV_HdmiTx_SetDviMode.
+*                       Removed support for reduced blanking
+* 1.3   YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XV_HdmiTx_Config
+*                       XV_HdmiTx_CfgInitialize
+* 1.4   YH     17/08/16 Added XV_HdmiTx_SetAxiClkFreq
+* 1.5   YH     14/11/16 Added XV_HdmiTx_Bridge_yuv420 & XV_HdmiTx_Bridge_pixel
+*                       mode macros
+* 1.6   MG     28/03/17 Added XV_HdmiTx_Mask macros
+* 1.7   YH     19/07/17 Added XV_HdmiTx_IsMasked macro
+*              22/08/17 Added XV_HdmiTx_Audio_LPCM macro
+*                       Added XV_HdmiTx_Audio_HBR macro
+* 1.8   YH     06/10/17 Replaced XV_HdmiTx_Audio_LPCM and XV_HdmiTx_Audio_HBR
+*                           macro with API XV_HdmiTx_SetAudioFormat
+*                       Added XV_HdmiTx_GetAudioFormat
+* 1.9   EB     24/10/17 Added enum XV_HdmiTx_AudioFormatType
+* 1.10  MMO    19/12/17 Added XV_HdmiTx_SetTmdsClk API
+* 2.0   EB     16/01/18 Updated function XV_HdmiTx_SetTmdsClk and renamed to
+*                           XV_HdmiTx_ConfigTmdsClk
+*                       Moved Vendor Specific InfoFrame related functions to
+*                           HDMI Common library
+*                       Deprecating XV_HdmiTx_VSIF_GeneratePacket,
+*                           XV_HdmiTx_VSIF_DisplayInfo,
+*                           XV_HdmiTx_VSIF_3DStructToString,
+*                           XV_HdmiTx_VSIF_3DSampMethodToString and
+*                           XV_HdmiTx_VSIF_3DSampPosToString APIs
+*                       Moved VicTable, XV_HdmiTx_Aux to Hdmi Common library
+*       EB     24/01/18 Added OverrideHdmi14Scrambler to XV_HdmiTx_Stream
+* 2.2   EB     03/08/18 Marked XV_HdmiTx_AudioMute and XV_HdmiTx_AudioUnmute
+*                           as deprecated
+*       MMO    11/08/18 Added Bridge Overflow and Bridge Underflow (PIO IN)
+* 2.5   EB     02/12/18 Added 3D Audio Support
+* </pre>
+*
+******************************************************************************/
+#ifndef XV_HDMITX_H_
+#define XV_HDMITX_H_        /**< Prevent circular inclusions
+                  *  by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmitx_hw.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+#include "xdebug.h"
+#include "xvidc.h"
+#include "xv_hdmic.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+/** @name Handler Types
+* @{
+*/
+/**
+* These constants specify different types of handler and used to differentiate
+* interrupt requests from peripheral.
+*/
+typedef enum {
+	XV_HDMITX_HANDLER_CONNECT = 1,  // Handler for connect
+	XV_HDMITX_HANDLER_TOGGLE,       // Handler for toggle
+	XV_HDMITX_HANDLER_BRDGUNLOCK,   // Handler for bridge unlocked
+	XV_HDMITX_HANDLER_BRDGOVERFLOW, // Handler for bridge overflow
+	XV_HDMITX_HANDLER_BRDGUNDERFLOW,// Handler for bridge underflow
+	XV_HDMITX_HANDLER_VS,           // Handler for vsync
+	XV_HDMITX_HANDLER_STREAM_DOWN,  // Handler for stream down
+	XV_HDMITX_HANDLER_STREAM_UP     // Handler for stream up
+} XV_HdmiTx_HandlerType;
+/*@}*/
+
+/** @name HDMI TX stream status
+* @{
+*/
+typedef enum {
+    XV_HDMITX_STATE_STREAM_DOWN,    // Stream down
+    XV_HDMITX_STATE_STREAM_UP       // Stream up
+} XV_HdmiTx_State;
+
+/** @name HDMI TX audio format
+* @{
+*/
+typedef enum {
+    XV_HDMITX_AUDFMT_LPCM = 0,    // L-PCM
+    XV_HDMITX_AUDFMT_HBR,         // HBR
+    XV_HDMITX_AUDFMT_3D           // 3D Audio
+} XV_HdmiTx_AudioFormatType;
+
+/**
+* This typedef contains configuration information for the HDMI TX core.
+* Each HDMI TX device should have a configuration structure associated.
+*/
+typedef struct {
+    u16 DeviceId;       /**< DeviceId is the unique ID of the HDMI TX core */
+    UINTPTR BaseAddress;    /**< BaseAddress is the physical
+                        * base address of the core's registers */
+	u32 AxiLiteClkFreq;
+} XV_HdmiTx_Config;
+
+/**
+* This typedef contains audio stream specific data structure
+*/
+typedef struct {
+    u8 Channels;            //< Video Identification code */
+} XV_HdmiTx_AudioStream;
+
+/**
+* This typedef contains HDMI TX stream specific data structure.
+*/
+typedef struct {
+    XVidC_VideoStream       Video;              /**< Video stream for HDMI TX */
+    XV_HdmiTx_AudioStream   Audio;              /**< Audio stream for HDMI TX */
+    u8                      Vic;                /**< Video Identification code
+                                                flag  */
+    u8                      IsHdmi;             /**< HDMI flag. 1 - HDMI Stream,
+                                                0 - DVI Stream  */
+    u8                      IsHdmi20;           /**< HDMI 2.0 flag  */
+    u8                      IsScrambled;        /**< Scrambler flag
+                                1 - scrambled data , 0 - non scrambled data */
+    u8			    OverrideScrambler; /**< Override scramble
+						    flag */
+    u32                     TMDSClock;          /**< TMDS clock */
+    u8                      TMDSClockRatio;     /**< TMDS clock ration
+                                0 - 1/10, 1 - 1/40 */
+    u32                     PixelClk;           /**< Pixel Clock  */
+    XV_HdmiTx_State         State;              /**< State */
+    u8                      IsConnected;        /**< Connected flag.
+                            This flag is set when the cable is connected  */
+    u8                      SampleRate;         /**< Sample rate */
+} XV_HdmiTx_Stream;
+
+/**
+* Callback type for Vsync event interrupt.
+*
+* @param    CallbackRef is a callback reference passed in by the upper
+*       layer when setting the callback functions, and passed back to
+*       the upper layer when the callback is invoked.
+*
+* @return   None.
+*
+* @note     None.
+*
+*/
+typedef void (*XV_HdmiTx_Callback)(void *CallbackRef);
+
+/**
+* The XV_HdmiTx driver instance data. An instance must be allocated for each
+* HDMI TX core in use.
+*/
+typedef struct {
+    XV_HdmiTx_Config Config;    /**< Hardware Configuration */
+    u32 IsReady;        /**< Core and the driver instance are initialized */
+
+    /* Callbacks */
+    XV_HdmiTx_Callback ConnectCallback;     /**< Callback for connect event
+                                            interrupt */
+    void *ConnectRef;                       /**< To be passed to the connect
+                                            interrupt callback */
+    u32 IsConnectCallbackSet;               /**< Set flag. This flag is set
+                                to true when the callback has been registered */
+
+    XV_HdmiTx_Callback ToggleCallback;     /**< Callback for toggle event
+                                            interrupt */
+    void *ToggleRef;                       /**< To be passed to the toggle
+                                            interrupt callback */
+    u32 IsToggleCallbackSet;               /**< Set flag. This flag is set
+                                to true when the callback has been registered */
+
+    XV_HdmiTx_Callback VsCallback;          /**< Callback for Vsync event
+                                            interrupt */
+    void *VsRef;                            /**< To be passed to the Vsync
+                                        interrupt callback */
+    u32 IsVsCallbackSet;                    /**< Set flag. This flag is set to
+                                true when the callback has been registered */
+
+    XV_HdmiTx_Callback BrdgUnlockedCallback;   /**< Callback for Bridge
+                                                 *UnLocked event interrupt */
+    void *BrdgUnlockedRef;                  /**< To be passed to the Bridge
+                                              Unlocked interrupt callback */
+    u32 IsBrdgUnlockedCallbackSet;       /**< Set flag. This flag is set to
+                                true when the callback has been registered */
+
+    XV_HdmiTx_Callback BrdgOverflowCallback;   /**< Callback for Bridge
+                                                  * Overflow event interrupt */
+    void *BrdgOverflowRef;                  /**< To be passed to the Bridge
+                                              Overflow interrupt callback */
+    u32 IsBrdgOverflowCallbackSet;       /**< Set flag. This flag is set to
+                                true when the callback has been registered */
+
+    XV_HdmiTx_Callback BrdgUnderflowCallback;   /**< Callback for Bridge
+                                                  * Underflow event
+                                                  * interrupt */
+    void *BrdgUnderflowRef;                  /**< To be passed to the Bridge
+                                              Underflow interrupt callback */
+    u32 IsBrdgUnderflowCallbackSet;       /**< Set flag. This flag is set to
+                                true when the callback has been registered */
+
+    XV_HdmiTx_Callback StreamDownCallback;  /**< Callback for stream down
+                                            callback */
+    void *StreamDownRef;                    /**< To be passed to the stream
+                                            down callback */
+    u32 IsStreamDownCallbackSet;            /**< Set flag. This flag is set to
+                                true when the callback has been registered */
+
+    XV_HdmiTx_Callback StreamUpCallback;    /**< Callback for stream up
+    callback */
+    void *StreamUpRef;                      /**< To be passed to the stream up
+    callback */
+    u32 IsStreamUpCallbackSet;              /**< Set flag. This flag is set to
+    true when the callback has been registered */
+
+    /* Aux peripheral specific */
+    XHdmiC_Aux Aux;                         /**< AUX peripheral information */
+
+    /* HDMI TX stream */
+    XV_HdmiTx_Stream Stream;                /**< HDMI TX stream information */
+    u32 CpuClkFreq;                         /* CPU Clock frequency */
+
+} XV_HdmiTx;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+*
+* This macro returns the clock cycles required to count up to 1MS with respect
+* to AXI Lite Frequency
+*
+* @param  InstancePtr is a pointer to the XV_HdmiTX core instance.
+*
+* @return None.
+*
+*
+******************************************************************************/
+#define XV_HdmiTx_GetTime1Ms(InstancePtr) \
+  (InstancePtr)->Config.AxiLiteClkFreq/1000
+
+/*****************************************************************************/
+/**
+*
+* This macro reads the TX version
+*
+* @param  InstancePtr is a pointer to the XV_HdmiTX core instance.
+*
+* @return None.
+*
+*
+******************************************************************************/
+#define XV_HdmiTx_GetVersion(InstancePtr) \
+  XV_HdmiTx_ReadReg((InstancePtr)->Config.BaseAddress, \
+  (XV_HDMITX_VER_VERSION_OFFSET))
+
+/*****************************************************************************/
+/**
+*
+* This macro asserts or releases the HDMI TX reset.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    Reset specifies TRUE/FALSE value to either assert or
+*       release HDMI TX reset.
+*
+* @return   None.
+*
+* @note     The reset output of the PIO is inverted. When the system is
+*       in reset, the PIO output is cleared and this will reset the
+*       HDMI RX. Therefore, clearing the PIO reset output will assert
+*       the HDMI link and video reset.
+*       C-style signature:
+*       void XV_HdmiTx_Reset(XV_HdmiTx *InstancePtr, u8 Reset)
+*
+******************************************************************************/
+#define XV_HdmiTx_Reset(InstancePtr, Reset) \
+{ \
+    if (Reset) { \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_RST_MASK)); \
+    } \
+    else { \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_RST_MASK)); \
+    } \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro controls the HDMI TX Scrambler.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+* @param    SetClr specifies TRUE/FALSE value to either set ON or clear
+*       Scrambler.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_SetScrambler(XV_HdmiTx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiTx_SetScrambler(InstancePtr, SetClr) \
+{ \
+    if (SetClr) { \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_SCRM_MASK)); \
+        (InstancePtr)->Stream.IsScrambled = (TRUE); \
+    } \
+    else { \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_SCRM_MASK)); \
+        (InstancePtr)->Stream.IsScrambled = (FALSE); \
+    } \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro controls the YUV420 mode for video bridge.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Tx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either enable or disable the
+*		YUV 420 Support.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiTx_Bridge_yuv420(XV_HdmiTx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiTx_Bridge_yuv420(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_PIO_OUT_SET_OFFSET), \
+						   (XV_HDMITX_PIO_OUT_BRIDGE_YUV420_MASK)); \
+	} \
+	else { \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_PIO_OUT_CLR_OFFSET), \
+						   (XV_HDMITX_PIO_OUT_BRIDGE_YUV420_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro controls the Pixel Repeat mode for video bridge.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Tx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either enable or disable the
+*		Pixel Repitition Support.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiTx_Bridge_pixel(XV_HdmiTx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiTx_Bridge_pixel(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_PIO_OUT_SET_OFFSET), \
+				   (XV_HDMITX_PIO_OUT_BRIDGE_PIXEL_MASK)); \
+	} \
+	else { \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_PIO_OUT_CLR_OFFSET), \
+				   (XV_HDMITX_PIO_OUT_BRIDGE_PIXEL_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI TX PIO peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_PioEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_PioEnable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_CTRL_SET_OFFSET), (XV_HDMITX_PIO_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI TX PIO peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_PioDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_PioDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_CTRL_CLR_OFFSET), (XV_HDMITX_PIO_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupt in the HDMI TX PIO peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_PioIntrEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_PioIntrEnable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_CTRL_SET_OFFSET), (XV_HDMITX_PIO_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupt in the HDMI TX PIO peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_PioIntrDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_PioIntrDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_CTRL_CLR_OFFSET), (XV_HDMITX_PIO_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro clears HDMI TX PIO interrupt.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_PioIntrClear(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_PioIntrClear(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_STA_OFFSET), (XV_HDMITX_PIO_STA_IRQ_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI TX Display Data Channel (DDC) peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_DdcEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_DdcEnable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_DDC_CTRL_SET_OFFSET), (XV_HDMITX_DDC_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI TX Display Data Channel (DDC) peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_DdcDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_DdcDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_DDC_CTRL_CLR_OFFSET), (XV_HDMITX_DDC_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupt in the HDMI TX DDC peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_DdcIntrEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_DdcIntrEnable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_DDC_CTRL_SET_OFFSET), (XV_HDMITX_DDC_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupt in the HDMI TX DDC peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_DdcIntrDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_DdcIntrDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_DDC_CTRL_CLR_OFFSET), (XV_HDMITX_DDC_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro clears HDMI TX DDC interrupt.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_DdcIntrClear(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_DdcIntrClear(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_DDC_STA_OFFSET), (XV_HDMITX_DDC_STA_IRQ_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables the HDMI TX Auxiliary (AUX) peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AuxEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_AuxEnable(InstancePtr) \
+{ \
+    if ((InstancePtr)->Stream.IsHdmi) { \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_AUX_CTRL_SET_OFFSET), (XV_HDMITX_AUX_CTRL_RUN_MASK)); \
+    } \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro disables the HDMI TX Auxiliary (AUX) peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AuxDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_AuxDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_AUX_CTRL_CLR_OFFSET), (XV_HDMITX_AUX_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables interrupt in the HDMI TX AUX peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AuxIntrEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_AuxIntrEnable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_AUX_CTRL_SET_OFFSET), (XV_HDMITX_AUX_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables interrupt in the HDMI TX AUX peripheral.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AuxIntrDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_AuxIntrDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_AUX_CTRL_CLR_OFFSET), (XV_HDMITX_AUX_CTRL_IE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro enables audio in HDMI TX core.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AudioEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_AudioEnable(InstancePtr) \
+{ \
+    if ((InstancePtr)->Stream.IsHdmi) { \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_AUD_CTRL_SET_OFFSET), (XV_HDMITX_AUD_CTRL_RUN_MASK)); \
+    } \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro disables audio in HDMI TX core.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AudioDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_AudioDisable(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_AUD_CTRL_CLR_OFFSET), (XV_HDMITX_AUD_CTRL_RUN_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro unmutes audio in HDMI TX core.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AudioUnmute(XV_HdmiTx *InstancePtr)
+*
+* @deprecated   XV_HdmiTx_AudioUnmute will be deprecated in 2019.3 and replaced
+*               by XV_HdmiTx_AudioEnable.
+*
+******************************************************************************/
+#define XV_HdmiTx_AudioUnmute(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_AUD_CTRL_SET_OFFSET), (XV_HDMITX_AUD_CTRL_RUN_MASK)) \
+	_Pragma ("GCC warning \"'XV_HdmiTx_AudioUnmute' macro is deprecated\"")
+
+/*****************************************************************************/
+/**
+*
+* This macro mutes audio in HDMI TX core.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_AudioMute(XV_HdmiTx *InstancePtr)
+*
+* @deprecated   XV_HdmiTx_AudioMute will be deprecated in 2019.3 and replaced
+*               by XV_HdmiTx_AudioDisable.
+*
+******************************************************************************/
+#define XV_HdmiTx_AudioMute(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_AUD_CTRL_CLR_OFFSET), (XV_HDMITX_AUD_CTRL_RUN_MASK)) \
+	_Pragma ("GCC warning \"'XV_HdmiTx_AudioMute' macro is deprecated\"")
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the mode bit.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_SetMode(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_SetMode(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_OUT_SET_OFFSET), (XV_HDMITX_PIO_OUT_MODE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro clears the mode bit.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_ClearMode(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_ClearMode(InstancePtr) \
+    XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_OUT_CLR_OFFSET), (XV_HDMITX_PIO_OUT_MODE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro provides the current mode.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   Current mode.
+*       0 = DVI
+*       1 = HDMI
+*
+* @note     C-style signature:
+*       u8 XV_HdmiTx_GetMode(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_GetMode(InstancePtr) \
+    (XV_HdmiTx_ReadReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_OUT_OFFSET)) & (XV_HDMITX_PIO_OUT_MODE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro provides the current sample rate.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   Sample rate
+*
+* @note     C-style signature:
+*       u8 XV_HdmiTx_GetSampleRate(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_GetSampleRate(InstancePtr) \
+    (InstancePtr)->Stream.SampleRate
+
+/*****************************************************************************/
+/**
+*
+* This macro provides the active audio channels.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   Audio channels
+*
+*
+******************************************************************************/
+#define XV_HdmiTx_GetAudioChannels(InstancePtr) \
+    (InstancePtr)->Stream.Audio.Channels
+
+/*****************************************************************************/
+/**
+*
+* This macro provides the current pixel packing phase.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   Pixel packing phase.
+*
+*
+******************************************************************************/
+#define XV_HdmiTx_GetPixelPackingPhase(InstancePtr) \
+    ( ( (XV_HdmiTx_ReadReg( (InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_PIO_IN_OFFSET) ) ) >> (XV_HDMITX_PIO_IN_PPP_SHIFT)) \
+    & (XV_HDMITX_PIO_IN_PPP_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This macro disables video mask in HDMI TX core.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_MaskDisable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_MaskDisable(InstancePtr) \
+{ \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_MASK_CTRL_CLR_OFFSET), (XV_HDMITX_MASK_CTRL_RUN_MASK)); \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro enables video mask in HDMI TX core.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*       void XV_HdmiTx_MaskEnable(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_MaskEnable(InstancePtr) \
+{ \
+        XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+        (XV_HDMITX_MASK_CTRL_SET_OFFSET), (XV_HDMITX_MASK_CTRL_RUN_MASK)); \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro enables or disables the noise in the video mask.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Tx core instance.
+* @param	SetClr specifies TRUE/FALSE value to either enable or disable the
+*		Noise.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiTx_MaskNoise(XV_HdmiTx *InstancePtr, u8 SetClr)
+*
+******************************************************************************/
+#define XV_HdmiTx_MaskNoise(InstancePtr, SetClr) \
+{ \
+	if (SetClr) { \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_MASK_CTRL_SET_OFFSET), \
+				   (XV_HDMITX_MASK_CTRL_NOISE_MASK)); \
+	} \
+	else { \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_MASK_CTRL_CLR_OFFSET), \
+				   (XV_HDMITX_MASK_CTRL_NOISE_MASK)); \
+	} \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the red component value in the video mask.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Tx core instance.
+* @param	Value
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiTx_MaskSetRed(XV_HdmiTx *InstancePtr, u16 Value)
+*
+******************************************************************************/
+#define XV_HdmiTx_MaskSetRed(InstancePtr, Value) \
+{ \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_MASK_RED_OFFSET), \
+				   (Value)); \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the green component value in the video mask.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Tx core instance.
+* @param	Value
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiTx_MaskSetGreen(XV_HdmiTx *InstancePtr, u16 Value)
+*
+******************************************************************************/
+#define XV_HdmiTx_MaskSetGreen(InstancePtr, Value) \
+{ \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_MASK_GREEN_OFFSET), \
+				   (Value)); \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro sets the blue component value in the video mask.
+*
+* @param	InstancePtr is a pointer to the XHdmi_Tx core instance.
+* @param	Value
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XV_HdmiTx_MaskSetBlue(XV_HdmiTx *InstancePtr, u16 Value)
+*
+******************************************************************************/
+#define XV_HdmiTx_MaskSetBlue(InstancePtr, Value) \
+{ \
+		XV_HdmiTx_WriteReg((InstancePtr)->Config.BaseAddress, \
+		                   (XV_HDMITX_MASK_BLUE_OFFSET), \
+				   (Value)); \
+}
+
+/*****************************************************************************/
+/**
+*
+* This macro provides the current video mask mode.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx core instance.
+*
+* @return   Current mode.
+*       0 = Video masking is disabled
+*       1 = Video masking is enabled
+*
+* @note     C-style signature:
+*       u8 XV_HdmiTx_IsMasked(XV_HdmiTx *InstancePtr)
+*
+******************************************************************************/
+#define XV_HdmiTx_IsMasked(InstancePtr) \
+    XV_HdmiTx_ReadReg((InstancePtr)->Config.BaseAddress, \
+    (XV_HDMITX_MASK_CTRL_OFFSET)) & (XV_HDMITX_MASK_CTRL_RUN_MASK)
+
+/************************** Function Prototypes ******************************/
+
+/* Initialization function in xv_hdmitx_sinit.c */
+XV_HdmiTx_Config *XV_HdmiTx_LookupConfig(u16 DeviceId);
+
+/* Initialization and control functions in xv_hdmitx.c */
+int XV_HdmiTx_CfgInitialize(XV_HdmiTx *InstancePtr,
+    XV_HdmiTx_Config *CfgPtr,
+    UINTPTR EffectiveAddr);
+void XV_HdmiTx_SetHdmiMode(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_SetDviMode(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_Clear(XV_HdmiTx *InstancePtr);
+u8 XV_HdmiTx_GetVic(XVidC_VideoMode VideoMode);
+XVidC_VideoMode XV_HdmiTx_GetVideoModeFromVic(u8 Vic);
+u32 XV_HdmiTx_SetStream(XV_HdmiTx *InstancePtr,
+    XVidC_VideoMode VideoMode,
+    XVidC_ColorFormat ColorFormat,
+    XVidC_ColorDepth Bpc,
+    XVidC_PixelsPerClock Ppc,
+    XVidC_3DInfo *Info3D);
+
+u32 XV_HdmiTx_GetTmdsClk (XV_HdmiTx *InstancePtr,
+    XVidC_VideoMode VideoMode,
+    XVidC_ColorFormat ColorFormat,
+    XVidC_ColorDepth Bpc);
+
+void XV_HdmiTx_INT_VRST(XV_HdmiTx *InstancePtr, u8 Reset);
+void XV_HdmiTx_INT_LRST(XV_HdmiTx *InstancePtr, u8 Reset);
+void XV_HdmiTx_EXT_VRST(XV_HdmiTx *InstancePtr, u8 Reset);
+void XV_HdmiTx_EXT_SYSRST(XV_HdmiTx *InstancePtr, u8 Reset);
+void XV_HdmiTx_SetGcpAvmuteBit(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_ClearGcpAvmuteBit(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_SetGcpClearAvmuteBit(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_ClearGcpClearAvmuteBit(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_SetPixelRate(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_SetSampleRate(XV_HdmiTx *InstancePtr, u8 SampleRate);
+void XV_HdmiTx_SetColorFormat(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_SetColorDepth(XV_HdmiTx *InstancePtr);
+int XV_HdmiTx_IsStreamScrambled(XV_HdmiTx *InstancePtr);
+int XV_HdmiTx_IsStreamConnected(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_SetAxiClkFreq(XV_HdmiTx *InstancePtr, u32 ClkFreq);
+void XV_HdmiTx_DdcInit(XV_HdmiTx *InstancePtr, u32 Frequency);
+int XV_HdmiTx_DdcWrite(XV_HdmiTx *InstancePtr, u8 Slave, u16 Length,
+    u8 *Buffer, u8 Stop);
+int XV_HdmiTx_DdcRead(XV_HdmiTx *InstancePtr, u8 Slave, u16 Length,
+    u8 *Buffer, u8 Stop);
+u32 XV_HdmiTx_AuxSend(XV_HdmiTx *InstancePtr);
+int XV_HdmiTx_Scrambler(XV_HdmiTx *InstancePtr);
+int XV_HdmiTx_ClockRatio(XV_HdmiTx *InstancePtr);
+int XV_HdmiTx_DetectHdmi20(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_ShowSCDC(XV_HdmiTx *InstancePtr);
+void XV_HdmiTx_DebugInfo(XV_HdmiTx *InstancePtr);
+int XV_HdmiTx_SetAudioChannels(XV_HdmiTx *InstancePtr, u8 Value);
+int XV_HdmiTx_SetAudioFormat(XV_HdmiTx *InstancePtr, XV_HdmiTx_AudioFormatType Value);
+XV_HdmiTx_AudioFormatType XV_HdmiTx_GetAudioFormat(XV_HdmiTx *InstancePtr);
+/* Self test function in xv_hdmitx_selftest.c */
+int XV_HdmiTx_SelfTest(XV_HdmiTx *InstancePtr);
+
+/* Interrupt related functions in xv_hdmitx_intr.c */
+void XV_HdmiTx_IntrHandler(void *InstancePtr);
+int XV_HdmiTx_SetCallback(XV_HdmiTx *InstancePtr,
+		XV_HdmiTx_HandlerType HandlerType,
+		void *CallbackFunc,
+		void *CallbackRef);
+
+
+/* [Linux] Not supporting vendor specific APIs */ 
+/************************** Variable Declarations ****************************/
+
+/************************** Variable Declarations ****************************/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* End of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx_hw.h
@@ -0,0 +1,391 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitx_hw.h
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx HDMI TX core.
+*
+* For more information about the operation of this core see the hardware
+* specification and documentation in the higher level driver xv_hdmitx.h file.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.01  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XV_HdmiTx_WriteReg
+*                       XV_HdmiTx_ReadReg
+* 1.02  YH     14/11/16 Added BRIDGE_YUV420 and BRIDGE_PIXEL mask to PIO Out
+* 1.03  MG     06/03/17 Added XV_HDMITX_AUX_STA_PKT_RDY_MASK
+* 1.04  MMO    03/05/17 Updated the comments for XV_HdmiTx_ReadReg and
+*                       	XV_HdmiTx_WriteReg
+* 1.1   MG     03/05/17 Introduced video mask peripheral
+* 1.2   YH     22/08/17 Added XV_HDMITX_AUD_CTRL_AUDFMT_MASK (Audio Format)
+* 1.3   YH     06/10/17 Added XV_HDMITX_AUD_CTRL_AUDFMT_SHIFT (Audio Format)
+* 1.4   YH     16/01/18 Added PIO_OUT for dedicated reset for each clock domain
+*                       Added PIO_IN to bridge unlock interrupt
+*                       Added PIO_OUT to set GCP_AVMUTE
+* 1.5   MMO    11/08/18 Added PIO_IN to bridge overflow and underflow interrupt
+*       EB     14/08/18 Added XV_HDMITX_HPD_TIMEGRID_OFFSET,
+*                       	XV_HDMITX_TOGGLE_CONF_OFFSET and
+*                       	XV_HDMITX_CONNECT_CONF_OFFSET
+* </pre>
+*
+******************************************************************************/
+#ifndef XV_HDMITX_HW_H_
+#define XV_HDMITX_HW_H_     /**< Prevent circular inclusions
+                  *  by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+
+/**< VER (Version Interface) peripheral register offsets */
+/**< The VER is the first peripheral on the local bus */
+#define XV_HDMITX_VER_BASE              (0*64)
+#define XV_HDMITX_VER_ID_OFFSET         ((XV_HDMITX_VER_BASE)+(0*4))/**<
+                                    * VER Identification *  Register offset */
+#define XV_HDMITX_VER_VERSION_OFFSET    ((XV_HDMITX_VER_BASE)+(1*4))/**<
+                                    * VER Version Register *  offset */
+
+/**< PIO (Parallel Interface) peripheral register offsets */
+/**< The PIO is the first peripheral on the local bus */
+#define XV_HDMITX_PIO_BASE              (1*64)
+#define XV_HDMITX_PIO_ID_OFFSET         ((XV_HDMITX_PIO_BASE)+(0*4))/**< PIO
+                                        * Identification *  Register offset */
+#define XV_HDMITX_PIO_CTRL_OFFSET       ((XV_HDMITX_PIO_BASE)+(1*4))/**< PIO
+                                        * Control Register *  offset */
+#define XV_HDMITX_PIO_CTRL_SET_OFFSET   ((XV_HDMITX_PIO_BASE)+(2*4))/**< PIO
+                                        * Control Register Set *  offset */
+#define XV_HDMITX_PIO_CTRL_CLR_OFFSET   ((XV_HDMITX_PIO_BASE)+(3*4))/**< PIO
+                                        * Control Register Clear *  offset */
+#define XV_HDMITX_PIO_STA_OFFSET        ((XV_HDMITX_PIO_BASE)+(4*4))/**< PIO
+                                        * Status Register *  offset */
+#define XV_HDMITX_PIO_OUT_OFFSET        ((XV_HDMITX_PIO_BASE)+(5*4))/**< PIO
+                                        * Out Register offset */
+#define XV_HDMITX_PIO_OUT_SET_OFFSET    ((XV_HDMITX_PIO_BASE)+(6*4))/**< PIO
+                                        * Out Register Set *  offset */
+#define XV_HDMITX_PIO_OUT_CLR_OFFSET    ((XV_HDMITX_PIO_BASE)+(7*4))/**< PIO
+                                        * Out Register Clear *  offset */
+#define XV_HDMITX_PIO_OUT_MSK_OFFSET    ((XV_HDMITX_PIO_BASE)+(8*4))/**< PIO
+                                        * Out Mask Register *  offset */
+#define XV_HDMITX_PIO_IN_OFFSET         ((XV_HDMITX_PIO_BASE)+(9*4))/**< PIO
+                                        * In Register offset */
+#define XV_HDMITX_PIO_IN_EVT_OFFSET     ((XV_HDMITX_PIO_BASE)+(10*4))/**< PIO
+                                        * In Event Register *  offset */
+#define XV_HDMITX_PIO_IN_EVT_RE_OFFSET  ((XV_HDMITX_PIO_BASE)+(11*4))/**< PIO
+                                        * In Event Rising Edge
+					*  Register offset */
+#define XV_HDMITX_PIO_IN_EVT_FE_OFFSET  ((XV_HDMITX_PIO_BASE)+(12*4))/**< PIO
+                                        * In Event Falling Edge
+					*  Register offset */
+#define XV_HDMITX_HPD_TIMEGRID_OFFSET   ((XV_HDMITX_PIO_BASE)+(13*4))/**< PIO
+                                        * HPD Config. *  offset */
+#define XV_HDMITX_TOGGLE_CONF_OFFSET    ((XV_HDMITX_PIO_BASE)+(14*4))/**< PIO
+                                        * HPD Config. *  Register offset */
+#define XV_HDMITX_CONNECT_CONF_OFFSET   ((XV_HDMITX_PIO_BASE)+(15*4))/**< PIO
+                                        * HPD Config. *  Register offset */
+
+// PIO peripheral Control register masks
+#define XV_HDMITX_PIO_CTRL_RUN_MASK     (1<<0)  /**< PIO Control Run mask */
+#define XV_HDMITX_PIO_CTRL_IE_MASK      (1<<1)  /**< PIO Control Interrupt
+                                                * Enable mask */
+
+// PIO peripheral Status register masks
+#define XV_HDMITX_PIO_STA_IRQ_MASK      (1<<0) /**< PIO Status Interrupt mask */
+#define XV_HDMITX_PIO_STA_EVT_MASK      (1<<1) /**< PIO Status Event mask */
+
+// PIO peripheral PIO Out register masks and shifts
+#define XV_HDMITX_PIO_OUT_RST_MASK          (1<<0)  /**< PIO Out Reset mask */
+#define XV_HDMITX_PIO_OUT_MODE_MASK         (1<<3)  /**< PIO Out Mode mask */
+#define XV_HDMITX_PIO_OUT_COLOR_DEPTH_MASK  0x30    /**< PIO Out Color Depth
+                                                    * mask */
+#define XV_HDMITX_PIO_OUT_PIXEL_RATE_MASK   0xC0    /**< PIO Out Pixel Rate
+                                                    * mask */
+#define XV_HDMITX_PIO_OUT_SAMPLE_RATE_MASK  0x300   /**< PIO Out Sample Rate
+                                                    * mask */
+#define XV_HDMITX_PIO_OUT_COLOR_SPACE_MASK  0xC00   /**< PIO Out Color Space
+                                                    * mask */
+#define XV_HDMITX_PIO_OUT_SCRM_MASK         (1<<12) /**< PIO Out Scrambler
+                                                    * mask */
+#define XV_HDMITX_PIO_OUT_COLOR_DEPTH_SHIFT 4   /**< PIO Out Color Depth
+                                                    * shift */
+#define XV_HDMITX_PIO_OUT_PIXEL_RATE_SHIFT  6   /**< PIO Out Pixel Rate
+                                                    * shift */
+#define XV_HDMITX_PIO_OUT_SAMPLE_RATE_SHIFT 8   /**< PIO Out Sample Rate
+                                                    * shift */
+#define XV_HDMITX_PIO_OUT_COLOR_SPACE_SHIFT 10  /**< PIO Out Color Space
+                                                    * shift */
+#define XV_HDMITX_PIO_OUT_GCP_CLEARAVMUTE_MASK    (1<<28) /**< PIO Out
+							  * GCP_CLEARAVMUTE mask */
+#define XV_HDMITX_PIO_OUT_BRIDGE_YUV420_MASK (1<<29) /**< PIO Out Bridge_YUV420
+                                                         * mask */
+#define XV_HDMITX_PIO_OUT_BRIDGE_PIXEL_MASK  (1<<30) /**< PIO Out Bridge_Pixel
+                                                         * repeat mask */
+#define XV_HDMITX_PIO_OUT_GCP_AVMUTE_MASK    (1<<31) /**< PIO Out GCP_AVMUTE
+                                                         * mask */
+#define XV_HDMITX_PIO_OUT_INT_VRST_MASK      (1<<0)  /**< PIO Out INT_VRST
+                                                         * mask */
+#define XV_HDMITX_PIO_OUT_INT_LRST_MASK      (1<<20) /**< PIO Out INT_LRST
+                                                        * mask */
+#define XV_HDMITX_PIO_OUT_EXT_VRST_MASK      (1<<21) /**< PIO Out EXT_VRST
+                                                        * mask */
+#define XV_HDMITX_PIO_OUT_EXT_SYSRST_MASK    (1<<22) /**< PIO Out EXT_SYSRST
+                                                         * mask */
+
+
+// PIO peripheral PIO In register masks
+#define XV_HDMITX_PIO_IN_LNK_RDY_MASK       (1<<0)  /**< PIO In link ready
+                                                    * mask */
+#define XV_HDMITX_PIO_IN_VID_RDY_MASK       (1<<1)  /**< PIO In video ready
+                                                    * mask */
+#define XV_HDMITX_PIO_IN_HPD_MASK           (1<<2)  /**< PIO In HPD mask */
+#define XV_HDMITX_PIO_IN_VS_MASK            (1<<3)  /**< PIO In Vsync mask */
+#define XV_HDMITX_PIO_IN_PPP_MASK           0x07    /**< PIO In Pixel packing
+                                                    * phase mask */
+#define XV_HDMITX_PIO_IN_HPD_TOGGLE_MASK    (1<<8)  /**< PIO In HPD toggle
+                                                     * mask */
+#define XV_HDMITX_PIO_IN_PPP_SHIFT          5       /**< PIO In Pixel packing
+                                                    * phase shift */
+#define XV_HDMITX_PIO_IN_BRDG_LOCKED_MASK   (1<<9) /**< PIO In Bridge Locked
+                                                    * mask */
+#define XV_HDMITX_PIO_IN_BRDG_OVERFLOW_MASK (1<<10) /**< PIO In Bridge Overflow
+                                                    * mask */
+#define XV_HDMITX_PIO_IN_BRDG_UNDERFLOW_MASK (1<<11) /**< PIO In Bridge
+                                                    * Underflow mask */
+
+/**< DDC (Display Data Channel) peripheral register offsets */
+/**< The DDC is the second peripheral on the local bus */
+#define XV_HDMITX_DDC_BASE                  (2*64)
+#define XV_HDMITX_DDC_ID_OFFSET             ((XV_HDMITX_DDC_BASE)+(0*4))/**< DDC
+                                * Identification *  Register offset */
+#define XV_HDMITX_DDC_CTRL_OFFSET           ((XV_HDMITX_DDC_BASE)+(1*4))/**< DDC
+                                * Control Register *  offset */
+#define XV_HDMITX_DDC_CTRL_SET_OFFSET       ((XV_HDMITX_DDC_BASE)+(2*4))/**< DDC
+                                * Control Register Set *  offset */
+#define XV_HDMITX_DDC_CTRL_CLR_OFFSET       ((XV_HDMITX_DDC_BASE)+(3*4))/**< DDC
+                                * Control Register Clear *  offset */
+#define XV_HDMITX_DDC_STA_OFFSET            ((XV_HDMITX_DDC_BASE)+(4*4))/**< DDC
+                                * Status Register *  offset */
+#define XV_HDMITX_DDC_CMD_OFFSET            ((XV_HDMITX_DDC_BASE)+(5*4))/**< DDC
+                                * Command Register *  offset */
+#define XV_HDMITX_DDC_DAT_OFFSET            ((XV_HDMITX_DDC_BASE)+(6*4))/**< DDC
+                                * Data Register *  offset */
+
+// DDC peripheral Control register masks and shift
+#define XV_HDMITX_DDC_CTRL_RUN_MASK         (1<<0)  /**< DDC Control Run mask */
+#define XV_HDMITX_DDC_CTRL_IE_MASK          (1<<1)  /**< DDC Control Interrupt
+                                                    *  Enable mask */
+#define XV_HDMITX_DDC_CTRL_CLK_DIV_MASK     0xFFFF  /**< DDC Control Clock
+                                                    * Divider mask */
+#define XV_HDMITX_DDC_CTRL_CLK_DIV_SHIFT    16  /**< DDC Control Clock
+                                                *Divider shift */ /*@}*/
+
+// DDC peripheral Status register masks
+#define XV_HDMITX_DDC_STA_IRQ_MASK      (1<<0)  /**< DDC Status IRQ mask */
+#define XV_HDMITX_DDC_STA_EVT_MASK      (1<<1)  /**< DDC Status Event mask */
+#define XV_HDMITX_DDC_STA_BUSY_MASK     (1<<2)  /**< DDC Status Busy mask */
+#define XV_HDMITX_DDC_STA_DONE_MASK     (1<<3)  /**< DDC Status Busy mask */
+#define XV_HDMITX_DDC_STA_TIMEOUT_MASK  (1<<4)  /**< DDC Status Timeout mask */
+#define XV_HDMITX_DDC_STA_ACK_MASK      (1<<5)  /**< DDC Status ACK mask */
+#define XV_HDMITX_DDC_STA_SCL_MASK      (1<<6)  /**< DDC State of SCL Input
+                                                * mask */
+#define XV_HDMITX_DDC_STA_SDA_MASK      (1<<7)  /**< DDC State of SDA Input
+                                                * mask */
+#define XV_HDMITX_DDC_STA_CMD_FULL      (1<<8)  /**< Command fifo full */
+#define XV_HDMITX_DDC_STA_DAT_EMPTY     (1<<9)  /**< Data fifo empty */
+#define XV_HDMITX_DDC_STA_CMD_WRDS_MASK 0xFF /**< Command fifo words mask*/
+#define XV_HDMITX_DDC_STA_CMD_WRDS_SHIFT    16  /**< Command fifo words shift */
+#define XV_HDMITX_DDC_STA_DAT_WRDS_MASK     0xFF /**< Data fifo words mask */
+#define XV_HDMITX_DDC_STA_DAT_WRDS_SHIFT    24  /**< Data fifo words shift */
+
+// DDC peripheral token
+#define XV_HDMITX_DDC_CMD_STR_TOKEN     (0x100) /**< Start token */
+#define XV_HDMITX_DDC_CMD_STP_TOKEN     (0x101) /**< Stop token */
+#define XV_HDMITX_DDC_CMD_RD_TOKEN      (0x102) /**< Read token */
+#define XV_HDMITX_DDC_CMD_WR_TOKEN      (0x103) /**< Write token */
+
+// Auxiliary (AUX) peripheral register offsets
+// The AUX is the third peripheral on the local bus
+#define XV_HDMITX_AUX_BASE              (3*64)
+#define XV_HDMITX_AUX_ID_OFFSET         ((XV_HDMITX_AUX_BASE)+(0*4)) /**< AUX
+                                * Identification *  Register offset */
+#define XV_HDMITX_AUX_CTRL_OFFSET       ((XV_HDMITX_AUX_BASE)+(1*4)) /**< AUX
+                                * Control Register *  offset */
+#define XV_HDMITX_AUX_CTRL_SET_OFFSET   ((XV_HDMITX_AUX_BASE)+(2*4)) /**< AUX
+                                * Control Register Set *  offset */
+#define XV_HDMITX_AUX_CTRL_CLR_OFFSET   ((XV_HDMITX_AUX_BASE)+(3*4)) /**< AUX
+                                * Control Register Clear *  offset */
+#define XV_HDMITX_AUX_STA_OFFSET        ((XV_HDMITX_AUX_BASE)+(4*4)) /**< AUX
+                                * Status Register *  offset */
+#define XV_HDMITX_AUX_DAT_OFFSET        ((XV_HDMITX_AUX_BASE)+(5*4)) /**< AUX
+                                * Data Register *  offset */
+
+// Auxiliary peripheral Control register masks
+#define XV_HDMITX_AUX_CTRL_RUN_MASK         (1<<0)  /**< AUX Control Run mask */
+#define XV_HDMITX_AUX_CTRL_IE_MASK          (1<<1)  /**< AUX Control Interrupt
+                                                    * Enable mask */
+
+// Auxiliary peripheral Status register masks and shift
+#define XV_HDMITX_AUX_STA_IRQ_MASK          (1<<0)  /**< AUX Status Interrupt
+                                                    *  mask */
+#define XV_HDMITX_AUX_STA_FIFO_EMT_MASK     (1<<1)  /**< AUX Status FIFO Empty
+                                                    *  mask */
+#define XV_HDMITX_AUX_STA_FIFO_FUL_MASK     (1<<2)  /**< AUX Status FIFO Full
+                                                    *  mask */
+#define XV_HDMITX_AUX_STA_PKT_RDY_MASK     (1<<3)  /**< AUX Status FIFO Ready
+                                                    *  mask */
+#define XV_HDMITX_AUX_STA_FREE_PKTS_MASK    0x0F    /**< AUX Status Free Packets
+                                                    *  mask */
+#define XV_HDMITX_AUX_STA_FREE_PKTS_SHIFT   15  /**< AUX Status Free
+                                                    *  Packets shift */
+
+
+// Audio (AUD) peripheral register offsets
+// The AUD is the forth peripheral on the local bus
+#define XV_HDMITX_AUD_BASE              (4*64)
+#define XV_HDMITX_AUD_ID_OFFSET         ((XV_HDMITX_AUD_BASE)+(0*4)) /**< AUD
+                                * Identification *  Register offset */
+#define XV_HDMITX_AUD_CTRL_OFFSET       ((XV_HDMITX_AUD_BASE)+(1*4)) /**< AUD
+                                * Control Register *  offset */
+#define XV_HDMITX_AUD_CTRL_SET_OFFSET   ((XV_HDMITX_AUD_BASE)+(2*4)) /**< AUD
+                                * Control Register Set *  offset */
+#define XV_HDMITX_AUD_CTRL_CLR_OFFSET   ((XV_HDMITX_AUD_BASE)+(3*4)) /**< AUD
+                                * Control Register Clear *  offset */
+#define XV_HDMITX_AUD_STA_OFFSET        ((XV_HDMITX_AUD_BASE)+(4*4)) /**< AUD
+                                * Status Register *  offset */
+#define XV_HDMITX_AUD_ACR_CTS_OFFSET    ((XV_HDMITX_AUD_BASE)+(5*4)) /**< AUD
+                                * Clock Regeneration CTS *  Register offset */
+#define XV_HDMITX_AUD_ACR_N_OFFSET      ((XV_HDMITX_AUD_BASE)+(6*4)) /**< AUD
+                                * Clock Regeneration N *  Register offset */
+
+// Audio peripheral Control register masks
+#define XV_HDMITX_AUD_CTRL_RUN_MASK     (1<<0)  /**< AUD Control Run mask */
+#define XV_HDMITX_AUD_CTRL_IE_MASK      (1<<1)  /**< AUD Control Interrupt
+                                                * Enable mask */
+#define XV_HDMITX_AUD_CTRL_CH_MASK      0x1F /**< AUD Control channels mask */
+#define XV_HDMITX_AUD_CTRL_CH_SHIFT     4    /**< AUD Control channels shift */
+#define XV_HDMITX_AUD_CTRL_AUDFMT_MASK  0x7 /**< AUD Control AUD Format
+                                                * mask */
+#define XV_HDMITX_AUD_CTRL_AUDFMT_SHIFT 9   /**< AUD Control AUD Format
+                                              * shift */
+
+// Audio peripheral Status register masks
+#define XV_HDMITX_AUD_STA_IRQ_MASK      (1<<0) /**< AUD Status Interrupt mask */
+
+// Video Mask (MASK) peripheral register offsets
+// The mask is the fifth peripheral on the local bus
+#define XV_HDMITX_MASK_BASE              (5*64)
+#define XV_HDMITX_MASK_ID_OFFSET         ((XV_HDMITX_MASK_BASE)+(0*4)) /**< MASK
+                                * Identification *  Register offset */
+#define XV_HDMITX_MASK_CTRL_OFFSET       ((XV_HDMITX_MASK_BASE)+(1*4)) /**< MASK
+                                * Control Register *  offset */
+#define XV_HDMITX_MASK_CTRL_SET_OFFSET   ((XV_HDMITX_MASK_BASE)+(2*4)) /**< MASK
+                                * Control Register Set *  offset */
+#define XV_HDMITX_MASK_CTRL_CLR_OFFSET   ((XV_HDMITX_MASK_BASE)+(3*4)) /**< MASK
+                                * Control Register Clear *  offset */
+#define XV_HDMITX_MASK_STA_OFFSET        ((XV_HDMITX_MASK_BASE)+(4*4)) /**< MASK
+                                * Status Register *  offset */
+#define XV_HDMITX_MASK_RED_OFFSET        ((XV_HDMITX_MASK_BASE)+(5*4)) /**< MASK
+                                * Red Component Register *  offset */
+#define XV_HDMITX_MASK_GREEN_OFFSET        ((XV_HDMITX_MASK_BASE)+(6*4)) /**< MASK
+                                * Green Component Register *  offset */
+#define XV_HDMITX_MASK_BLUE_OFFSET        ((XV_HDMITX_MASK_BASE)+(7*4)) /**< MASK
+                                * Blue Component Register *  offset */
+
+// Video mask peripheral Control register masks
+#define XV_HDMITX_MASK_CTRL_RUN_MASK     (1<<0)  /**< MASK Control Run mask */
+#define XV_HDMITX_MASK_CTRL_NOISE_MASK   (1<<2)  /**< MASK Control Noise */
+
+// Peripheral ID and General shift values.
+#define XV_HDMITX_SHIFT_16  16  /**< 16 shift value */
+#define XV_HDMITX_MASK_16   0xFFFF  /**< 16 bit mask value */
+#define XV_HDMITX_PIO_ID    0x2200  /**< TX's PIO ID */
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+// Register access macro definition
+#define XV_HdmiTx_In32  Xil_In32    /**< Input Operations */
+#define XV_HdmiTx_Out32 Xil_Out32   /**< Output Operations */
+
+/*****************************************************************************/
+/**
+*
+* This macro reads a value from a HDMI TX register. A 32 bit read is performed.
+* If the component is implemented in a smaller width, only the least
+* significant data is read from the register. The most significant data
+* will be read as 0.
+*
+* @param    BaseAddress is the base address of the HDMI TX core instance.
+* @param    RegOffset is the register offset of the register (defined at
+*       the top of this file).
+*
+* @return   The 32-bit value of the register.
+*
+* @note     C-style signature:
+*           u32 XV_HdmiTx_ReadReg(UINTPTR BaseAddress, u32 RegOffset)
+*
+******************************************************************************/
+#define XV_HdmiTx_ReadReg(BaseAddress, RegOffset) \
+    XV_HdmiTx_In32((BaseAddress) + (RegOffset))
+
+/*****************************************************************************/
+/**
+*
+* This macro writes a value to a HDMI TX register. A 32 bit write is performed.
+* If the component is implemented in a smaller width, only the least
+* significant data is written.
+*
+* @param    BaseAddress is the base address of the HDMI TX core instance.
+* @param    RegOffset is the register offset of the register (defined at
+*       the top of this file) to be written.
+* @param    Data is the 32-bit value to write into the register.
+*
+* @return   None.
+*
+* @note     C-style signature:
+*           void XV_HdmiTx_WriteReg(UINTPTR BaseAddress, u32 RegOffset, u32 Data)
+*
+******************************************************************************/
+#define XV_HdmiTx_WriteReg(BaseAddress, RegOffset, Data) \
+    XV_HdmiTx_Out32((BaseAddress) + (RegOffset), (u32)(Data))
+/*@}*/
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Declarations ****************************/
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx_intr.c
@@ -0,0 +1,383 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitx_intr.c
+*
+* This file contains interrupt related functions for Xilinx HDMI TX core.
+* Please see xv_hdmitx.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   YH     18/08/16 squash unused variable compiler warning
+* 1.2   YH     16/01/18 Added bridge unlock interrupt
+* 1.3   MMO    11/08/18 Added bridge overflow and underflow interrupt
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmitx.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+/* [Linux] Cannot make static as it is being called from TX driver wrapper code */
+void HdmiTx_PioIntrHandler(XV_HdmiTx *InstancePtr);
+void HdmiTx_DdcIntrHandler(XV_HdmiTx *InstancePtr);
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the HDMI TX driver.
+*
+* This handler reads the pending interrupt from PIO and DDC peripheral,
+* determines the source of the interrupts, clears the interrupts and calls
+* callbacks accordingly.
+*
+* The application is responsible for connecting this function to the interrupt
+* system. Application beyond this driver is also responsible for providing
+* callbacks to handle interrupts and installing the callbacks using
+* XV_HdmiTx_SetCallback() during initialization phase. An example delivered
+* with this driver demonstrates how this could be done.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTx instance that just
+*       interrupted.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTx_IntrHandler(void *InstancePtr)
+{
+    u32 Data;
+    XV_HdmiTx *HdmiTxPtr = (XV_HdmiTx *)InstancePtr;
+
+    /* Verify arguments */
+    Xil_AssertVoid(HdmiTxPtr != NULL);
+    Xil_AssertVoid(HdmiTxPtr->IsReady == XIL_COMPONENT_IS_READY);
+
+    /* PIO */
+    Data = XV_HdmiTx_ReadReg(HdmiTxPtr->Config.BaseAddress,
+                            (XV_HDMITX_PIO_STA_OFFSET)) &
+                            (XV_HDMITX_PIO_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to PIO handler */
+        HdmiTx_PioIntrHandler(HdmiTxPtr);
+    }
+
+    /* DDC */
+    Data = XV_HdmiTx_ReadReg(HdmiTxPtr->Config.BaseAddress,
+                            (XV_HDMITX_DDC_STA_OFFSET)) &
+                            (XV_HDMITX_DDC_STA_IRQ_MASK);
+
+    /* Check for IRQ flag set */
+    if (Data) {
+        /* Jump to DDC handler */
+        HdmiTx_DdcIntrHandler(HdmiTxPtr);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType              Callback Function Type
+* -----------------------  --------------------------------------------------
+* (XV_HDMITX_HANDLER_HPD)   HpdCallback
+* (XV_HDMITX_HANDLER_VS)    VsCallback
+* </pre>
+*
+* @param    InstancePtr is a pointer to the HDMI TX core instance.
+* @param    HandlerType specifies the type of handler.
+* @param    CallbackFunc is the address of the callback function.
+* @param    CallbackRef is a user data item that will be passed to the
+*       callback function when it is invoked.
+*
+* @return
+*       - XST_SUCCESS if callback function installed successfully.
+*       - XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note     Invoking this function for a handler that already has been
+*       installed replaces it with the new handler.
+*
+******************************************************************************/
+int XV_HdmiTx_SetCallback(XV_HdmiTx *InstancePtr,
+			XV_HdmiTx_HandlerType HandlerType,
+			void *CallbackFunc,
+			void *CallbackRef)
+{
+    u32 Status;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(HandlerType >= (XV_HDMITX_HANDLER_CONNECT));
+    Xil_AssertNonvoid(CallbackFunc != NULL);
+    Xil_AssertNonvoid(CallbackRef != NULL);
+
+    /* Check for handler type */
+    switch (HandlerType) {
+        case (XV_HDMITX_HANDLER_CONNECT):
+            InstancePtr->ConnectCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->ConnectRef = CallbackRef;
+            InstancePtr->IsConnectCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMITX_HANDLER_TOGGLE):
+            InstancePtr->ToggleCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->ToggleRef = CallbackRef;
+            InstancePtr->IsToggleCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMITX_HANDLER_BRDGUNLOCK):
+            InstancePtr->BrdgUnlockedCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->BrdgUnlockedRef = CallbackRef;
+            InstancePtr->IsBrdgUnlockedCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMITX_HANDLER_BRDGOVERFLOW):
+            InstancePtr->BrdgOverflowCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->BrdgOverflowRef = CallbackRef;
+            InstancePtr->IsBrdgOverflowCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMITX_HANDLER_BRDGUNDERFLOW):
+            InstancePtr->BrdgUnderflowCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->BrdgUnderflowRef = CallbackRef;
+            InstancePtr->IsBrdgUnderflowCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        case (XV_HDMITX_HANDLER_VS):
+            InstancePtr->VsCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->VsRef = CallbackRef;
+            InstancePtr->IsVsCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream down
+        case (XV_HDMITX_HANDLER_STREAM_DOWN):
+            InstancePtr->StreamDownCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->StreamDownRef = CallbackRef;
+            InstancePtr->IsStreamDownCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream up
+        case (XV_HDMITX_HANDLER_STREAM_UP):
+            InstancePtr->StreamUpCallback = (XV_HdmiTx_Callback)CallbackFunc;
+            InstancePtr->StreamUpRef = CallbackRef;
+            InstancePtr->IsStreamUpCallbackSet = (TRUE);
+            Status = (XST_SUCCESS);
+            break;
+
+        default:
+            Status = (XST_INVALID_PARAM);
+            break;
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the HDMI TX PIO peripheral interrupt handler.
+*
+* This handler reads corresponding event interrupt from the PIO_IN_EVT
+* register. It determines the source of the interrupts and calls according
+* callbacks.
+*
+* @param    InstancePtr is a pointer to the HDMI TX core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiTx_PioIntrHandler(XV_HdmiTx *InstancePtr)
+{
+    u32 Event;
+    u32 Data;
+
+    /* Read PIO IN Event register.*/
+    Event = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+                            (XV_HDMITX_PIO_IN_EVT_OFFSET));
+
+    /* Clear event flags */
+    XV_HdmiTx_WriteReg(InstancePtr->Config.BaseAddress,
+                    (XV_HDMITX_PIO_IN_EVT_OFFSET),
+                    (Event));
+
+    /* Read data */
+    Data = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+                            (XV_HDMITX_PIO_IN_OFFSET));
+
+    /* HPD event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_HPD_TOGGLE_MASK)) {
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsToggleCallbackSet) {
+            InstancePtr->ToggleCallback(InstancePtr->ToggleRef);
+        }
+    }
+
+    /* HPD event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_HPD_MASK)) {
+
+        // Check the HPD status
+        if ((Data) & (XV_HDMITX_PIO_IN_HPD_MASK))
+            InstancePtr->Stream.IsConnected = (TRUE);   // Set connected flag
+        else
+            InstancePtr->Stream.IsConnected = (FALSE);  // Clear connected flag
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsConnectCallbackSet) {
+            InstancePtr->ConnectCallback(InstancePtr->ConnectRef);
+        }
+    }
+
+    /* Bridge Unlocked event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_BRDG_LOCKED_MASK)) {
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsBrdgUnlockedCallbackSet) {
+            InstancePtr->BrdgUnlockedCallback(InstancePtr->BrdgUnlockedRef);
+        }
+    }
+
+    /* Bridge Overflow event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_BRDG_OVERFLOW_MASK)) {
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsBrdgOverflowCallbackSet) {
+            InstancePtr->BrdgOverflowCallback(InstancePtr->BrdgOverflowRef);
+        }
+    }
+
+    /* Bridge Underflow event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_BRDG_UNDERFLOW_MASK)) {
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsBrdgUnderflowCallbackSet) {
+            InstancePtr->BrdgUnderflowCallback(InstancePtr->BrdgUnderflowRef);
+        }
+    }
+
+    /* Vsync event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_VS_MASK)) {
+
+        // Check if user callback has been registered
+        if (InstancePtr->IsVsCallbackSet) {
+            InstancePtr->VsCallback(InstancePtr->VsRef);
+        }
+    }
+
+    /* Link ready event has occurred */
+    if ((Event) & (XV_HDMITX_PIO_IN_LNK_RDY_MASK)) {
+
+        // Check the link status
+        if ((Data) & (XV_HDMITX_PIO_IN_LNK_RDY_MASK)) {
+            // Set stream status to up
+            InstancePtr->Stream.State = XV_HDMITX_STATE_STREAM_UP;
+
+            /* Enable the AUX peripheral */
+            XV_HdmiTx_AuxEnable(InstancePtr);
+
+            /* Enable the AUX peripheral interrupt */
+            XV_HdmiTx_AuxIntrEnable(InstancePtr);
+
+            /* Enable audio */
+            //XV_HdmiTx_AudioEnable(InstancePtr);
+
+            // Check if user callback has been registered
+            if (InstancePtr->IsStreamUpCallbackSet) {
+                InstancePtr->StreamUpCallback(InstancePtr->StreamUpRef);
+            }
+        }
+
+        // Link down
+        else {
+            // Set stream status to down
+            InstancePtr->Stream.State = XV_HDMITX_STATE_STREAM_DOWN;
+
+            /* Disable Audio */
+            XV_HdmiTx_AudioDisable(InstancePtr);
+
+            /* Disable AUX */
+            XV_HdmiTx_AuxDisable(InstancePtr);
+
+            // Check if user callback has been registered
+            if (InstancePtr->IsStreamDownCallbackSet) {
+                InstancePtr->StreamDownCallback(InstancePtr->StreamDownRef);
+            }
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is the HDMI TX DDC peripheral interrupt handler.
+*
+* This handler reads DDC Status register and determines the timeout. It also
+* determines the state and based on that performs required operation.
+*
+*
+* @param    InstancePtr is a pointer to the HDMI TX core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void HdmiTx_DdcIntrHandler(XV_HdmiTx *InstancePtr)
+{
+    u32 Data;
+
+    /* Read DDC Status register */
+    Data = XV_HdmiTx_ReadReg(InstancePtr->Config.BaseAddress,
+                            (XV_HDMITX_DDC_STA_OFFSET));
+    Data = Data; //squash unused variable compiler warning
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitx_sinit.c
@@ -0,0 +1,93 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitx_sinit.c
+*
+* This file contains static initialization method for Xilinx HDMI TX core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00         10/07/15 Initial release.
+
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xv_hdmitx.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XV_HdmiTx_Config structure based
+* on the core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xv_hdmitx_g.c file.
+*
+* @param    DeviceId is the unique core ID of the HDMI TX core for the
+*       lookup operation.
+*
+* @return   XV_HdmiTx_LookupConfig returns a reference to a config record
+*       in the configuration table (in xv_hdmitx_g.c) corresponding
+*       to <i>DeviceId</i>, or NULL if no match is found.
+*
+* @note     None.
+*
+******************************************************************************/
+XV_HdmiTx_Config *XV_HdmiTx_LookupConfig(u16 DeviceId)
+{
+    extern XV_HdmiTx_Config
+            XV_HdmiTx_ConfigTable[XPAR_XV_HDMITX_NUM_INSTANCES];
+    XV_HdmiTx_Config *CfgPtr = NULL;
+    u32 Index;
+
+    /* Checking for device id for which instance it is matching */
+    for (Index = (u32)0x0; Index < (u32)(XPAR_XV_HDMITX_NUM_INSTANCES);
+                                Index++) {
+
+        /* Assigning address of config table if both device ids
+         * are matched
+         */
+        if (XV_HdmiTx_ConfigTable[Index].DeviceId == DeviceId) {
+            CfgPtr = &XV_HdmiTx_ConfigTable[Index];
+            break;
+        }
+    }
+
+    return (XV_HdmiTx_Config *)CfgPtr;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss.c
@@ -0,0 +1,2924 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitxss.c
+*
+* This is main code of Xilinx HDMI Transmitter Subsystem device driver.
+* Please see xv_hdmitxss.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.01  MG     17/12/16 Fixed issue in function SetAudioChannels
+*                       Updated function XV_HdmiTxSs_SendAuxInfoframe
+* 1.02  yh     12/01/16 Check vtc existance before configuring it
+* 1.03  yh     15/01/16 Add 3D Support
+* 1.04  yh     20/01/16 Added remapper support
+* 1.05  yh     01/02/16 Added set_ppc api
+* 1.06  yh     01/02/16 Removed xil_print "Cable (dis)connected"
+* 1.07  yh     15/02/16 Added default value to XV_HdmiTxSs_ConfigRemapper
+* 1.08  MG     03/02/16 Added HDCP support
+* 1.09  MG     09/03/16 Added XV_HdmiTxSs_SetHdmiMode and XV_HdmiTxSs_SetDviMode
+*                       Removed reduced blanking support
+* 1.10  MH     03/15/16 Moved HDCP 2.2 reset from stream up/down callback to
+*                       connect callback
+* 1.11  YH     18/03/16 Add XV_HdmiTxSs_SendGenericAuxInfoframe function
+* 1.12  MH     23/04/16 1. HDCP 1.x driver now uses AXI timer 4.1, so updated
+*                       to use AXI Timer config structure to determine timer
+*                       clock frequency
+*                       2. HDCP 1.x driver has fixed the problem where the
+*                       reset for the receiver causes the entire DDC peripheral
+*                       to get reset. Based on this change the driver has been
+*                       updated to use XV_HdmiTxSs_HdcpReset and
+*                       XV_HdmiTxSs_HdcpReset functions directly.
+*                       3. Updated XV_HdmiTxSs_HdcpEnable and
+*                       XV_HdmiTxSs_HdcpEnable functions to ensure that
+*                       HDCP 1.4 and 2.2 are mutually exclusive.
+*                       This fixes the problem where HDCP 1.4 and 2.2
+*                       state machines are running simultaneously.
+* 1.13   MH    23/06/16 Added HDCP repeater support.
+* 1.14   YH    18/07/16 1. Replace xil_print with xdbg_printf.
+*                       2. XV_HdmiTx_VSIF VSIF global variable local to
+*                        XV_HdmiTxSs_SendVSInfoframe
+*                       3. Replace MB_Sleep() with usleep
+*                       4. Remove checking VideoMode < XVIDC_VM_NUM_SUPPORTED in
+*                       XV_HdmiTxSs_SetStream to support customized video format
+* 1.15   YH    25/07/16 Used UINTPTR instead of u32 for BaseAddress
+*                       XV_HdmiTxSs_CfgInitialize
+* 1.16   YH    04/08/16 Remove unused functions
+*                       XV_HdmiTxSs_GetSubSysStruct
+* 1.17   MH    08/08/16 Updates to optimize out HDCP when excluded.
+* 1.18   YH    17/08/16 Remove sleep in XV_HdmiTxSs_ResetRemapper
+*                       Added Event Log
+*                       Combine Report function into one ReportInfo
+* 1.19   YH    27/08/16 Remove unused functions XV_HdmiTxSs_SetUserTimerHandler
+*                       XV_HdmiTxSs_WaitUs
+* 1.20   MH    08/10/16 Update function call sequence in
+*                       XV_HdmiTxSs_StreamUpCallback
+*
+* 1.1x   mmo   04/11/16 Updated the XV_HdmiTxSs_SetAudioChannels API which
+*                       currently calls XV_HdmiTx_SetAudioChannels driver,
+*                       which sets the Audio Channels
+*                       accordingly. This fixed is made during v1.2 (2016.1)
+* 1.21  YH     14/11/16 Added API to enable/disable YUV420/Pixel Repeat Mode
+*                       for video bridge
+* 1.22  YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.23  mmo    03/01/17 Move HDCP Related API to xv_hdmitxss_hdcp.c
+*                       Remove inclusion of the xenv.h and sleep.h as it not
+*                           used
+*                       Replaced "print" with "xil_printf"
+*                       Replace Carriage Return (\r) and Line Feed (\n) order,\
+*                           where the Carriage Return + Line Feed order is used.
+* 1.24  mmo    02/03/17 Added XV_HdmiTxSs_ReadEdidSegment API for Multiple
+*                             Segment Support and HDMI Compliance Test
+*                       Updated the XV_HdmiTxSs_ShowEdid API to have support
+*                             multiple EDID.
+* 1.25  MH     21/04/17 Updated to set HDMI mode in functions
+*                             XV_HdmiTxSS_SetHdmiMode and XV_HdmiTxSS_SetDviMode.
+* 1.40  YH     07/07/17 Fixed issue with VTC register read when video clock is
+*                             not present
+*                       Report HDMI/DVI mode in HDMI example design info log
+*                       Added Video Masking APIs
+* 1.41  mmo    02/08/17 Initialize the hdcp1.4 first before the hdcp1.4 timer
+*                              as the hdcp1.4 timer requires hdcp1.4 to be
+*                              initialize
+*       MH     09/08/17 Added function XV_HdmiTxSs_HdcpSetCapability
+*              22/08/17 Added function XV_HdmiTxSs_SetAudioFormat
+* 1.42  YH     06/10/17 Updated function XV_HdmiTxSs_SetAudioFormat
+*                       Added function XV_HdmiTxSs_GetAudioFormat
+*       EB     17/10/17 Added function XV_HdmiTxSs_ReportAudio
+*                       Updated function XV_HdmiTxSs_ReportInfo
+* 1.43  MMO    19/12/17 Added XV_HdmiTxSS_SetTMDS API
+* 5.00  EB     16/01/18 Updated XV_HdmiTxSS_SetTMDS API
+*                       Updated XV_HdmiTxSs_SetVideoStream API
+*                       Moved XV_HdmiTxSs_SendVSInfoframe function to HDMI
+*							    Common Library
+*                       Updated function XV_HdmiTxSs_StreamStart,
+*                               XV_HdmiTxSs_SendGenericAuxInfoframe
+*                       Added function XV_HdmiTxSs_GetAviInfoframe,
+*                           XV_HdmiTxSs_GetAudioInfoframe, XV_HdmiTxSs_GetVSIF
+*                           XV_HdmiTxSs_GetAuxiliary
+*                       Updated XV_HdmiTxSs_ConfigBridgeMode so Pixel
+*                           Pepetition AVI InfoFrame is sent out
+*                       Deprecating XV_HdmiTxSs_SendAviInfoframe and
+*                           XV_HdmiTxSs_SendGeneralControlPacket APIs
+*       YH     16/01/18 Added dedicated reset for each clock domain
+*                       Added bridge unlock interrupt
+*                       Added PIO_OUT to set GCP_AVMUTE
+*       EB     23/01/18 Added function
+*                           XV_HdmiTxSs_SetVideoStreamHdmi14ScramblingOverrideFlag
+*              25/01/18 Added function XV_HdmiTxSs_SetScrambler
+*              01/02/18	Updated function XV_HdmiTxSs_VtcSetup and changed the
+*                           input parameters to it to enable logging of
+*                           unsupported video timing by VTC
+*       SM     28/02/18 Added definition of XV_HdmiTxSS_SetAppVersion() API
+* 5.20  EB     03/08/18 Updated XV_HdmiTxSS_MaskSetRed, XV_HdmiTxSS_MaskSetGreen,
+*                           XV_HdmiTxSS_MaskSetBlue API
+*                       Replaced XV_HdmiTx_AudioMute API call with
+*                           XV_HdmiTx_AudioDisable
+*                       Replaced XV_HdmiTx_AudioUnmute API call with
+*                           XV_HdmiTx_AudioEnable
+*                       Replaced XV_HdmiTx_AudioUnmute API call with
+* 		MMO    11/08/18 Added Bridge Overflow and Bridge Underflow Interrupt
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include "xv_hdmitxss.h"
+#include "xv_hdmitxss_coreinit.h"
+
+/************************** Constant Definitions *****************************/
+/* Pixel definition in 8 bit resolution in YUV color space*/
+static const u8 bkgndColorYUV[XV_BKGND_LAST][3] =
+{
+  {  0, 128, 128}, //Black
+  {255, 128, 128}, //White
+  { 76,  85, 255}, //Red
+  {149,  43,  21}, //Green
+  { 29, 255, 107}, //Blue
+  {  0,   0,   0}  //Place holder for Noise Video Mask
+};
+
+/* Pixel map in RGB color space*/
+/* {Green, Blue, Red} */
+static const u8 bkgndColorRGB[XV_BKGND_LAST][3] =
+{
+  {0, 0, 0}, //Black
+  {1, 1, 1}, //White
+  {0, 0, 1}, //Red
+  {1, 0, 0}, //Green
+  {0, 1, 0}, //Blue
+  {0, 0, 0}  //Place holder for Noise Video Mask
+};
+
+/**************************** Type Definitions *******************************/
+/**
+ * This typedef declares the driver instances of all the cores in the subsystem
+ */
+typedef struct
+{
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  XTmrCtr HdcpTimer;
+  XHdcp1x Hdcp14;
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  XHdcp22_Tx  Hdcp22;
+#endif
+  XV_HdmiTx HdmiTx;
+  XVtc Vtc;
+}XV_HdmiTxSs_SubCores;
+
+/**************************** Local Global ***********************************/
+XV_HdmiTxSs_SubCores XV_HdmiTxSs_SubCoreRepo[XPAR_XV_HDMITXSS_NUM_INSTANCES];
+                /**< Define Driver instance of all sub-core
+                                    included in the design */
+
+/************************** Function Prototypes ******************************/
+static void XV_HdmiTxSs_GetIncludedSubcores(XV_HdmiTxSs *HdmiTxSsPtr,
+                                            u16 DevId);
+static int XV_HdmiTxSs_RegisterSubsysCallbacks(XV_HdmiTxSs *InstancePtr);
+static int XV_HdmiTxSs_VtcSetup(XV_HdmiTxSs *HdmiTxSsPtr);
+static u32 XV_HdmiTxSS_SetTMDS(XV_HdmiTxSs *InstancePtr,
+                        XVidC_VideoMode VideoMode,
+                        XVidC_ColorFormat ColorFormat,
+                        XVidC_ColorDepth Bpc);
+static void XV_HdmiTxSs_ConnectCallback(void *CallbackRef);
+static void XV_HdmiTxSs_ToggleCallback(void *CallbackRef);
+static void XV_HdmiTxSs_BrdgUnlockedCallback(void *CallbackRef);
+static void XV_HdmiTxSs_BrdgOverflowCallback(void *CallbackRef);
+static void XV_HdmiTxSs_BrdgUnderflowCallback(void *CallbackRef);
+static void XV_HdmiTxSs_VsCallback(void *CallbackRef);
+static void XV_HdmiTxSs_StreamUpCallback(void *CallbackRef);
+static void XV_HdmiTxSs_StreamDownCallback(void *CallbackRef);
+static u32 XV_HdmiTxSS_GetVidMaskColorValue(XV_HdmiTxSs *InstancePtr,
+											u16 Value);
+
+static void XV_HdmiTxSs_ReportCoreInfo(XV_HdmiTxSs *InstancePtr);
+static void XV_HdmiTxSs_ReportTiming(XV_HdmiTxSs *InstancePtr);
+static void XV_HdmiTxSs_ReportAudio(XV_HdmiTxSs *InstancePtr);
+static void XV_HdmiTxSs_ReportSubcoreVersion(XV_HdmiTxSs *InstancePtr);
+
+static void XV_HdmiTxSs_ConfigBridgeMode(XV_HdmiTxSs *InstancePtr);
+
+/***************** Macros (Inline Functions) Definitions *********************/
+/*****************************************************************************/
+/**
+* This macro selects the bridge YUV420 mode
+*
+* @param  InstancePtr is a pointer to the HDMI TX Subsystem
+*
+*****************************************************************************/
+#define XV_HdmiTxSs_BridgeYuv420(InstancePtr, Enable) \
+{ \
+    XV_HdmiTx_Bridge_yuv420(InstancePtr->HdmiTxPtr, Enable); \
+}
+
+/*****************************************************************************/
+/**
+* This macro selects the bridge pixel repeat mode
+*
+* @param  InstancePtr is a pointer to the HDMI TX Subsystem
+*
+*****************************************************************************/
+#define XV_HdmiTxSs_BridgePixelRepeat(InstancePtr, Enable) \
+{ \
+    XV_HdmiTx_Bridge_pixel(InstancePtr->HdmiTxPtr, Enable); \
+}
+/************************** Function Definition ******************************/
+
+/*****************************************************************************/
+/**
+ * This function sets the core into HDMI mode
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiTxSS_SetHdmiMode(XV_HdmiTxSs *InstancePtr)
+{
+    XV_HdmiTx_SetHdmiMode(InstancePtr->HdmiTxPtr);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, TRUE);
+    }
+#endif
+}
+
+/*****************************************************************************/
+/**
+ * This function sets the core into DVI mode
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiTxSS_SetDviMode(XV_HdmiTxSs *InstancePtr)
+{
+    XV_HdmiTx_SetDviMode(InstancePtr->HdmiTxPtr);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetHdmiMode(InstancePtr->Hdcp14Ptr, FALSE);
+    }
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function reports list of cores included in Video Processing Subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance.
+*
+* @return None
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ReportCoreInfo(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  xil_printf("\r\n  ->HDMI TX Subsystem Cores\r\n");
+
+  /* Report all the included cores in the subsystem instance */
+  if (InstancePtr->HdmiTxPtr) {
+    xil_printf("    : HDMI TX \r\n");
+  }
+
+  if (InstancePtr->VtcPtr) {
+    xil_printf("    : VTC Core \r\n");
+  }
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if (InstancePtr->Hdcp14Ptr) {
+    xil_printf("    : HDCP 1.4 TX \r\n");
+  }
+
+  if (InstancePtr->HdcpTimerPtr) {
+    xil_printf("    : HDCP: AXIS Timer\r\n");
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  if (InstancePtr->Hdcp22Ptr) {
+    xil_printf("    : HDCP 2.2 TX \r\n");
+  }
+#endif
+}
+
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDMI TX
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiTxSS_HdmiTxIntrHandler(XV_HdmiTxSs *InstancePtr)
+{
+    XV_HdmiTx_IntrHandler(InstancePtr->HdmiTxPtr);
+}
+/*****************************************************************************/
+/**
+ * This function register's all sub-core ISR's with interrupt controller and
+ * any subsystem level call back function with requisite sub-core
+ *
+ * @param  InstancePtr is a pointer to the Subsystem instance to be
+ *       worked on.
+ *
+ *****************************************************************************/
+static int XV_HdmiTxSs_RegisterSubsysCallbacks(XV_HdmiTxSs *InstancePtr)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = InstancePtr;
+
+  /** Register HDMI callbacks */
+  if (HdmiTxSsPtr->HdmiTxPtr) {
+    /*
+     * Register call back for Tx Core Interrupts.
+     */
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_CONNECT,
+						  (void *)XV_HdmiTxSs_ConnectCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_TOGGLE,
+						  (void *)XV_HdmiTxSs_ToggleCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_BRDGUNLOCK,
+						  (void *)XV_HdmiTxSs_BrdgUnlockedCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_BRDGOVERFLOW,
+						  (void *)XV_HdmiTxSs_BrdgOverflowCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_BRDGUNDERFLOW,
+						  (void *)XV_HdmiTxSs_BrdgUnderflowCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_VS,
+						  (void *)XV_HdmiTxSs_VsCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_STREAM_UP,
+						  (void *)XV_HdmiTxSs_StreamUpCallback,
+						  (void *)InstancePtr);
+
+    XV_HdmiTx_SetCallback(HdmiTxSsPtr->HdmiTxPtr,
+                          XV_HDMITX_HANDLER_STREAM_DOWN,
+						  (void *)XV_HdmiTxSs_StreamDownCallback,
+						  (void *)InstancePtr);
+  }
+
+  return(XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function queries the subsystem instance configuration to determine
+* the included sub-cores. For each sub-core that is present in the design
+* the sub-core driver instance is binded with the subsystem sub-core driver
+* handle
+*
+* @param  HdmiTxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+static void XV_HdmiTxSs_GetIncludedSubcores(XV_HdmiTxSs *HdmiTxSsPtr, u16 DevId)
+{
+  HdmiTxSsPtr->HdmiTxPtr     = ((HdmiTxSsPtr->Config.HdmiTx.IsPresent)    \
+                        ? (&XV_HdmiTxSs_SubCoreRepo[DevId].HdmiTx) : NULL);
+  HdmiTxSsPtr->VtcPtr        = ((HdmiTxSsPtr->Config.Vtc.IsPresent)  \
+                        ? (&XV_HdmiTxSs_SubCoreRepo[DevId].Vtc) : NULL);
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  HdmiTxSsPtr->Hdcp14Ptr       = ((HdmiTxSsPtr->Config.Hdcp14.IsPresent) \
+                        ? (&XV_HdmiTxSs_SubCoreRepo[DevId].Hdcp14) : NULL);
+  HdmiTxSsPtr->HdcpTimerPtr  = ((HdmiTxSsPtr->Config.HdcpTimer.IsPresent) \
+                        ? (&XV_HdmiTxSs_SubCoreRepo[DevId].HdcpTimer) : NULL);
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  // HDCP 2.2
+  HdmiTxSsPtr->Hdcp22Ptr       = ((HdmiTxSsPtr->Config.Hdcp22.IsPresent) \
+                        ? (&XV_HdmiTxSs_SubCoreRepo[DevId].Hdcp22) : NULL);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the video subsystem and included sub-cores.
+* This function must be called prior to using the subsystem. Initialization
+* includes setting up the instance data for top level as well as all included
+* sub-core therein, and ensuring the hardware is in a known stable state.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+* @param  CfgPtr points to the configuration structure associated with the
+*         subsystem instance.
+* @param  EffectiveAddr is the base address of the device. If address
+*         translation is being used, then this parameter must reflect the
+*         virtual base address. Otherwise, the physical address should be
+*         used.
+*
+* @return XST_SUCCESS if initialization is successful else XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_CfgInitialize(XV_HdmiTxSs *InstancePtr,
+                              XV_HdmiTxSs_Config *CfgPtr,
+                              UINTPTR EffectiveAddr)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = InstancePtr;
+
+  /* Verify arguments */
+  Xil_AssertNonvoid(HdmiTxSsPtr != NULL);
+  Xil_AssertNonvoid(CfgPtr != NULL);
+  Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+  /* Setup the instance */
+  memcpy((void *)&(HdmiTxSsPtr->Config), (const void *)CfgPtr,
+    sizeof(XV_HdmiTxSs_Config));
+  HdmiTxSsPtr->Config.BaseAddress = EffectiveAddr;
+
+  /* Initialize InfoFrame */
+  (void)memset((void *)&(HdmiTxSsPtr->AVIInfoframe), 0, sizeof(XHdmiC_AVI_InfoFrame));
+  (void)memset((void *)&(HdmiTxSsPtr->VSIF), 0, sizeof(XHdmiC_VSIF));
+  (void)memset((void *)&(HdmiTxSsPtr->AudioInfoframe), 0, sizeof(XHdmiC_AudioInfoFrame));
+  memset((void *)&(HdmiTxSsPtr->DrmInfoframe), 0, sizeof(struct v4l2_hdr10_payload));
+  HdmiTxSsPtr->DrmInfoframe.metadata_type = 0xff;
+  HdmiTxSsPtr->DrmInfoframe.eotf = 0xff;
+
+  /* Determine sub-cores included in the provided instance of subsystem */
+  XV_HdmiTxSs_GetIncludedSubcores(HdmiTxSsPtr, CfgPtr->DeviceId);
+
+  /* Initialize all included sub_cores */
+  if (HdmiTxSsPtr->HdmiTxPtr) {
+    if (XV_HdmiTxSs_SubcoreInitHdmiTx(HdmiTxSsPtr) != XST_SUCCESS) {
+      return(XST_FAILURE);
+    }
+    XV_HdmiTx_SetAxiClkFreq(HdmiTxSsPtr->HdmiTxPtr,
+                            HdmiTxSsPtr->Config.AxiLiteClkFreq);
+  }
+
+  if (HdmiTxSsPtr->VtcPtr) {
+    if (XV_HdmiTxSs_SubcoreInitVtc(HdmiTxSsPtr) != XST_SUCCESS) {
+      return(XST_FAILURE);
+    }
+  }
+
+  /* Register Callbacks */
+  XV_HdmiTxSs_RegisterSubsysCallbacks(HdmiTxSsPtr);
+
+  /* Set default HDCP protocol */
+  HdmiTxSsPtr->HdcpProtocol = XV_HDMITXSS_HDCP_NONE;
+
+  /* HDCP ready flag */
+
+#ifdef USE_HDCP_TX
+  /* Default value */
+  HdmiTxSsPtr->HdcpIsReady = (FALSE);
+#endif
+
+  /* Set the flag to indicate the subsystem is ready */
+  XV_HdmiTxSs_Reset(HdmiTxSsPtr);
+  HdmiTxSsPtr->IsReady = XIL_COMPONENT_IS_READY;
+
+  return(XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the hdcp subsystem and included sub-cores.
+* This function must be called prior to using the subsystem. Initialization
+* includes setting up the instance data for top level as well as all included
+* sub-core therein, and ensuring the hardware is in a known stable state.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+* @param  CfgPtr points to the configuration structure associated with the
+*         subsystem instance.
+* @param  EffectiveAddr is the base address of the device. If address
+*         translation is being used, then this parameter must reflect the
+*         virtual base address. Otherwise, the physical address should be
+*         used.
+*
+* @return XST_SUCCESS if initialization is successful else XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_CfgInitializeHdcp(XV_HdmiTxSs *InstancePtr,
+                              XV_HdmiTxSs_Config *CfgPtr,
+                              UINTPTR EffectiveAddr)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = InstancePtr;
+
+  /* Verify arguments */
+  Xil_AssertNonvoid(HdmiTxSsPtr != NULL);
+  Xil_AssertNonvoid(CfgPtr != NULL);
+  Xil_AssertNonvoid(EffectiveAddr != (UINTPTR)NULL);
+
+  // HDCP 1.4
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if (HdmiTxSsPtr->Hdcp14Ptr) {
+    if (XV_HdmiTxSs_SubcoreInitHdcp14(HdmiTxSsPtr) != XST_SUCCESS){
+      return(XST_FAILURE);
+    }
+  }
+
+  if (HdmiTxSsPtr->HdcpTimerPtr) {
+    if (XV_HdmiTxSs_SubcoreInitHdcpTimer(HdmiTxSsPtr) != XST_SUCCESS){
+      return(XST_FAILURE);
+    }
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  // HDCP 2.2
+  if (HdmiTxSsPtr->Hdcp22Ptr) {
+    if (XV_HdmiTxSs_SubcoreInitHdcp22(HdmiTxSsPtr) != XST_SUCCESS){
+      return(XST_FAILURE);
+    }
+  }
+#endif
+
+  /* HDCP ready flag */
+#ifdef USE_HDCP_TX
+  /* Default value */
+  HdmiTxSsPtr->HdcpIsReady = (FALSE);
+  XV_HdmiTxSs_HdcpSetCapability(HdmiTxSsPtr, XV_HDMITXSS_HDCP_BOTH);
+#endif
+
+#if defined(XPAR_XHDCP_NUM_INSTANCES) && defined(XPAR_XHDCP22_TX_NUM_INSTANCES)
+  /* HDCP is ready when both HDCP cores are instantiated and both keys
+     are loaded */
+  if (HdmiTxSsPtr->Hdcp14Ptr && HdmiTxSsPtr->Hdcp22Ptr &&
+      HdmiTxSsPtr->Hdcp22Lc128Ptr && HdmiTxSsPtr->Hdcp22SrmPtr &&
+      HdmiTxSsPtr->Hdcp14KeyPtr) {
+    HdmiTxSsPtr->HdcpIsReady = (TRUE);
+  }
+#endif
+
+#if defined(XPAR_XHDCP_NUM_INSTANCES)
+  /* HDCP is ready when only the HDCP 1.4 core is instantiated and the key
+     is loaded */
+  if (!HdmiTxSsPtr->HdcpIsReady && HdmiTxSsPtr->Hdcp14Ptr &&
+       HdmiTxSsPtr->Hdcp14KeyPtr) {
+    HdmiTxSsPtr->HdcpIsReady = (TRUE);
+  }
+#endif
+
+#if defined(XPAR_XHDCP22_TX_NUM_INSTANCES)
+  /* HDCP is ready when only the HDCP 2.2 core is instantiated and the key
+     is loaded */
+  if (!HdmiTxSsPtr->HdcpIsReady && HdmiTxSsPtr->Hdcp22Ptr &&
+       HdmiTxSsPtr->Hdcp22Lc128Ptr &&
+      HdmiTxSsPtr->Hdcp22SrmPtr) {
+    HdmiTxSsPtr->HdcpIsReady = (TRUE);
+  }
+#endif
+
+  return(XST_SUCCESS);
+}
+/****************************************************************************/
+/**
+* This function starts the HDMI TX subsystem including all sub-cores that are
+* included in the processing pipeline for a given use-case. Video pipe is
+* started from back to front
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+* @note Cores are started only if the corresponding start flag in the scratch
+*       pad memory is set. This allows to selectively start only those cores
+*       included in the processing chain
+******************************************************************************/
+void XV_HdmiTxSs_Start(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_START, 0);
+#endif
+}
+
+/*****************************************************************************/
+/**
+* This function stops the HDMI TX subsystem including all sub-cores
+* Stop the video pipe starting from front to back
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_Stop(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_STOP, 0);
+#endif
+  if (InstancePtr->VtcPtr) {
+    /* Disable VTC */
+    XVtc_DisableGenerator(InstancePtr->VtcPtr);
+  }
+}
+
+/*****************************************************************************/
+/**
+* This function resets the video subsystem sub-cores. There are 2 reset
+* networks within the subsystem
+*  - For cores that are on AXIS interface
+*  - For cores that are on AXI-MM interface
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_Reset(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_RESET, 0);
+#endif
+  /* Assert HDMI TXCore resets */
+  XV_HdmiTxSs_TXCore_LRST(InstancePtr, TRUE);
+  XV_HdmiTxSs_TXCore_VRST(InstancePtr, TRUE);
+
+  /* Assert VID_OUT bridge resets */
+  XV_HdmiTxSs_SYSRST(InstancePtr, TRUE);
+  XV_HdmiTxSs_VRST(InstancePtr, TRUE);
+
+  /* Release VID_IN bridge resets */
+  XV_HdmiTxSs_SYSRST(InstancePtr, FALSE);
+  XV_HdmiTxSs_VRST(InstancePtr, FALSE);
+
+  /* Release HDMI TXCore resets */
+  XV_HdmiTxSs_TXCore_LRST(InstancePtr, FALSE);
+  XV_HdmiTxSs_TXCore_VRST(InstancePtr, FALSE);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the Internal Video reset
+* of the HDMI subcore within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_TXCore_VRST(XV_HdmiTxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_INT_VRST(InstancePtr->HdmiTxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the Internal Link reset
+* of the HDMI subcore within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_TXCore_LRST(XV_HdmiTxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_INT_LRST(InstancePtr->HdmiTxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the video reset of other
+* blocks within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_VRST(XV_HdmiTxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_EXT_VRST(InstancePtr->HdmiTxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function asserts or releases the system reset of other
+* blocks within the subsystem
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_SYSRST(XV_HdmiTxSs *InstancePtr, u8 Reset)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_EXT_SYSRST(InstancePtr->HdmiTxPtr, Reset);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the HDMI TX AUX GCP register AVMUTE bit.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetGcpAvmuteBit(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_SetGcpAvmuteBit(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+* This function clears the HDMI TX AUX GCP register AVMUTE bit.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_ClearGcpAvmuteBit(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_ClearGcpAvmuteBit(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+* This function sets the HDMI TX AUX GCP register CLEAR_AVMUTE bit.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetGcpClearAvmuteBit(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_SetGcpClearAvmuteBit(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+* This function clears the HDMI TX AUX GCP register CLEAR_AVMUTE bit.
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSs_ClearGcpClearAvmuteBit(XV_HdmiTxSs *InstancePtr)
+{
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  XV_HdmiTx_ClearGcpClearAvmuteBit(InstancePtr->HdmiTxPtr);
+}
+/*****************************************************************************/
+/**
+*
+* This function configures Video Timing Controller (VTC).
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiTxSs_VtcSetup(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+  /* Polarity configuration */
+  XVtc_Polarity Polarity;
+  XVtc_SourceSelect SourceSelect;
+  XVtc_Timing VideoTiming;
+  u32 HdmiTx_Hblank;
+  u32 Vtc_Hblank;
+
+  /* Disable Generator */
+  XVtc_Reset(HdmiTxSsPtr->VtcPtr);
+  XVtc_DisableGenerator(HdmiTxSsPtr->VtcPtr);
+  XVtc_Disable(HdmiTxSsPtr->VtcPtr);
+
+  /* Set up source select */
+  memset((void *)&SourceSelect, 0, sizeof(SourceSelect));
+
+  /* 1 = Generator registers, 0 = Detector registers */
+  SourceSelect.VChromaSrc = 1;
+  SourceSelect.VActiveSrc = 1;
+  SourceSelect.VBackPorchSrc = 1;
+  SourceSelect.VSyncSrc = 1;
+  SourceSelect.VFrontPorchSrc = 1;
+  SourceSelect.VTotalSrc = 1;
+  SourceSelect.HActiveSrc = 1;
+  SourceSelect.HBackPorchSrc = 1;
+  SourceSelect.HSyncSrc = 1;
+  SourceSelect.HFrontPorchSrc = 1;
+  SourceSelect.HTotalSrc = 1;
+
+  XVtc_SetSource(HdmiTxSsPtr->VtcPtr, &SourceSelect);
+
+  VideoTiming.HActiveVideo = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HActive;
+  VideoTiming.HFrontPorch = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HFrontPorch;
+  VideoTiming.HSyncWidth = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HSyncWidth;
+  VideoTiming.HBackPorch = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HBackPorch;
+  VideoTiming.HSyncPolarity = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HSyncPolarity;
+
+  /* Vertical Timing */
+  VideoTiming.VActiveVideo = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.VActive;
+
+  VideoTiming.V0FrontPorch = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.F0PVFrontPorch;
+  VideoTiming.V0BackPorch = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.F0PVBackPorch;
+  VideoTiming.V0SyncWidth = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.F0PVSyncWidth;
+
+  VideoTiming.V1FrontPorch = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.F1VFrontPorch;
+  VideoTiming.V1SyncWidth = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.F1VSyncWidth;
+  VideoTiming.V1BackPorch = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.F1VBackPorch;
+
+  VideoTiming.VSyncPolarity = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.VSyncPolarity;
+
+  VideoTiming.Interlaced = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.IsInterlaced;
+
+    /* 4 pixels per clock */
+    if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.PixPerClk == XVIDC_PPC_4) {
+    	/* If the parameters below are not divisible by the current PPC setting,
+    	 * log an error as VTC does not support such video timing
+    	 */
+		if (VideoTiming.HActiveVideo & 0x3 || VideoTiming.HFrontPorch & 0x3 ||
+				VideoTiming.HBackPorch & 0x3 || VideoTiming.HSyncWidth & 0x3) {
+#ifdef XV_HDMITXSS_LOG_ENABLE
+				XV_HdmiTxSs_LogWrite(HdmiTxSsPtr,
+						XV_HDMITXSS_LOG_EVT_VTC_RES_ERR, 0);
+#endif
+		}
+		VideoTiming.HActiveVideo = VideoTiming.HActiveVideo/4;
+		VideoTiming.HFrontPorch = VideoTiming.HFrontPorch/4;
+		VideoTiming.HBackPorch = VideoTiming.HBackPorch/4;
+		VideoTiming.HSyncWidth = VideoTiming.HSyncWidth/4;
+    }
+
+    /* 2 pixels per clock */
+    else if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.PixPerClk == XVIDC_PPC_2) {
+    	/* If the parameters below are not divisible by the current PPC setting,
+    	 * log an error as VTC does not support such video timing
+    	 */
+		if (VideoTiming.HActiveVideo & 0x1 || VideoTiming.HFrontPorch & 0x1 ||
+				VideoTiming.HBackPorch & 0x1 || VideoTiming.HSyncWidth & 0x1) {
+#ifdef XV_HDMITXSS_LOG_ENABLE
+			XV_HdmiTxSs_LogWrite(HdmiTxSsPtr,
+					XV_HDMITXSS_LOG_EVT_VTC_RES_ERR, 0);
+#endif
+		}
+		VideoTiming.HActiveVideo = VideoTiming.HActiveVideo/2;
+		VideoTiming.HFrontPorch = VideoTiming.HFrontPorch/2;
+		VideoTiming.HBackPorch = VideoTiming.HBackPorch/2;
+		VideoTiming.HSyncWidth = VideoTiming.HSyncWidth/2;
+    }
+
+    /* 1 pixels per clock */
+    else {
+		VideoTiming.HActiveVideo = VideoTiming.HActiveVideo;
+		VideoTiming.HFrontPorch = VideoTiming.HFrontPorch;
+		VideoTiming.HBackPorch = VideoTiming.HBackPorch;
+		VideoTiming.HSyncWidth = VideoTiming.HSyncWidth;
+    }
+
+    /* For YUV420 the line width is double there for double the blanking */
+    if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.ColorFormatId == XVIDC_CSF_YCRCB_420) {
+    	/* If the parameters below are not divisible by the current PPC setting,
+    	 * log an error as VTC does not support such video timing
+    	 */
+		if (VideoTiming.HActiveVideo & 0x1 || VideoTiming.HFrontPorch & 0x1 ||
+				VideoTiming.HBackPorch & 0x1 || VideoTiming.HSyncWidth & 0x1) {
+#ifdef XV_HDMITXSS_LOG_ENABLE
+			XV_HdmiTxSs_LogWrite(HdmiTxSsPtr,
+					XV_HDMITXSS_LOG_EVT_VTC_RES_ERR, 0);
+#endif
+		}
+		VideoTiming.HActiveVideo = VideoTiming.HActiveVideo/2;
+		VideoTiming.HFrontPorch = VideoTiming.HFrontPorch/2;
+		VideoTiming.HBackPorch = VideoTiming.HBackPorch/2;
+		VideoTiming.HSyncWidth = VideoTiming.HSyncWidth/2;
+    }
+
+/** When compensating the vtc horizontal timing parameters for the pixel mode
+* (quad or dual) rounding errors might be introduced (due to the divide)
+* If this happens, the vtc total horizontal blanking is less than the hdmi tx
+* horizontal blanking.
+* As a result the hdmi tx vid out bridge is not able to lock to
+* the incoming video stream.
+* This process will check the horizontal blank timing and compensate
+* for this condition.
+* Calculate hdmi tx horizontal blanking */
+
+  HdmiTx_Hblank = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HFrontPorch +
+    HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HSyncWidth +
+    HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Timing.HBackPorch;
+
+  do {
+    // Calculate vtc horizontal blanking
+    Vtc_Hblank = VideoTiming.HFrontPorch +
+        VideoTiming.HBackPorch +
+        VideoTiming.HSyncWidth;
+
+    // Quad pixel mode
+    if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.PixPerClk == XVIDC_PPC_4) {
+      Vtc_Hblank *= 4;
+    }
+
+    // Dual pixel mode
+    else if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.PixPerClk == XVIDC_PPC_2) {
+      Vtc_Hblank *= 2;
+    }
+
+    // Single pixel mode
+    else {
+      //Vtc_Hblank *= 1;
+    }
+
+    /* For YUV420 the line width is double there for double the blanking */
+    if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.ColorFormatId == XVIDC_CSF_YCRCB_420) {
+        Vtc_Hblank *= 2;
+    }
+
+    // If the horizontal total blanking differs,
+    // then increment the Vtc horizontal front porch.
+    if (Vtc_Hblank != HdmiTx_Hblank) {
+      VideoTiming.HFrontPorch++;
+    }
+
+  } while (Vtc_Hblank < HdmiTx_Hblank);
+
+  if (Vtc_Hblank != HdmiTx_Hblank) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "Error! Current format with total Hblank (%d) cannot \r\n",
+                  HdmiTx_Hblank);
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "       be transmitted with pixels per clock = %d\r\n",
+                  HdmiTxSsPtr->HdmiTxPtr->Stream.Video.PixPerClk);
+      return (XST_FAILURE);
+  }
+
+  XVtc_SetGeneratorTiming(HdmiTxSsPtr->VtcPtr, &VideoTiming);
+
+  /* Set up Polarity of all outputs */
+  memset((void *)&Polarity, 0, sizeof(XVtc_Polarity));
+  Polarity.ActiveChromaPol = 1;
+  Polarity.ActiveVideoPol = 1;
+
+  //Polarity.FieldIdPol = 0;
+  if (VideoTiming.Interlaced) {
+    Polarity.FieldIdPol = 1;
+  }
+  else {
+    Polarity.FieldIdPol = 0;
+  }
+
+  Polarity.VBlankPol = VideoTiming.VSyncPolarity;
+  Polarity.VSyncPol = VideoTiming.VSyncPolarity;
+  Polarity.HBlankPol = VideoTiming.HSyncPolarity;
+  Polarity.HSyncPol = VideoTiming.HSyncPolarity;
+
+  XVtc_SetPolarity(HdmiTxSsPtr->VtcPtr, &Polarity);
+
+  /* VTC driver does not take care of the setting of the VTC in
+   * interlaced operation. As a work around the register
+   * is set manually */
+  if (VideoTiming.Interlaced) {
+    /* Interlaced mode */
+    XVtc_WriteReg(HdmiTxSsPtr->VtcPtr->Config.BaseAddress, 0x68, 0x42);
+  }
+  else {
+    /* Progressive mode */
+    XVtc_WriteReg(HdmiTxSsPtr->VtcPtr->Config.BaseAddress, 0x68, 0x2);
+  }
+
+  /* Enable generator module */
+  XVtc_Enable(HdmiTxSsPtr->VtcPtr);
+  XVtc_EnableGenerator(HdmiTxSsPtr->VtcPtr);
+  XVtc_RegUpdateEnable(HdmiTxSsPtr->VtcPtr);
+
+  return (XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function set the TMDSClock and return it.
+*
+* @param  None.
+*
+* @return Calculated TMDS Clock
+*
+* @note   None.
+*
+*****************************************************************************/
+static u32 XV_HdmiTxSS_SetTMDS(XV_HdmiTxSs *InstancePtr,
+                        XVidC_VideoMode VideoMode,
+                        XVidC_ColorFormat ColorFormat,
+                        XVidC_ColorDepth Bpc) {
+
+    u32 TmdsClk;
+
+    TmdsClk = XV_HdmiTx_GetTmdsClk(InstancePtr->HdmiTxPtr,
+                                     VideoMode,
+                                     ColorFormat,
+                                     Bpc);
+
+    /* Store TMDS clock for future reference */
+	InstancePtr->HdmiTxPtr->Stream.TMDSClock = TmdsClk;
+
+    return TmdsClk;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a TX connect event has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ConnectCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+  /* Is the cable connected */
+  if (XV_HdmiTx_IsStreamConnected(HdmiTxSsPtr->HdmiTxPtr)) {
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_CONNECT, 0);
+#endif
+
+    /* Reset DDC */
+    XV_HdmiTx_DdcDisable(HdmiTxSsPtr->HdmiTxPtr);
+
+    /* Set stream connected flag */
+    HdmiTxSsPtr->IsStreamConnected = (TRUE);
+
+#ifdef USE_HDCP_TX
+    /* Push connect event to the HDCP event queue */
+    XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_CONNECT_EVT);
+#endif
+  }
+
+  /* TX cable is disconnected */
+  else {
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_DISCONNECT, 0);
+#endif
+    /* Assert HDMI TXCore link reset */
+    XV_HdmiTxSs_TXCore_LRST(HdmiTxSsPtr, TRUE);
+    XV_HdmiTxSs_TXCore_VRST(HdmiTxSsPtr, TRUE);
+
+    /* Assert SYSCLK VID_OUT bridge reset */
+    XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, TRUE);
+    XV_HdmiTxSs_VRST(HdmiTxSsPtr, TRUE);
+
+    /* Reset DDC */
+    XV_HdmiTx_DdcDisable(HdmiTxSsPtr->HdmiTxPtr);
+
+    /* Set stream connected flag */
+    HdmiTxSsPtr->IsStreamConnected = (FALSE);
+
+#ifdef USE_HDCP_TX
+    /* Push disconnect event to the HDCP event queue */
+    XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_DISCONNECT_EVT);
+#endif
+  }
+
+  /* Check if user callback has been registered */
+  if (HdmiTxSsPtr->ConnectCallback) {
+    HdmiTxSsPtr->ConnectCallback(HdmiTxSsPtr->ConnectRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a TX toggle event has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ToggleCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+  /* Reset DDC */
+  XV_HdmiTx_DdcDisable(HdmiTxSsPtr->HdmiTxPtr);
+
+  /* Set toggle flag */
+  HdmiTxSsPtr->IsStreamToggled = TRUE;
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_TOGGLE, 0);
+#endif
+  /* Check if user callback has been registered */
+  if (HdmiTxSsPtr->ToggleCallback) {
+    HdmiTxSsPtr->ToggleCallback(HdmiTxSsPtr->ToggleRef);
+  }
+
+  /* Clear toggle flag */
+  HdmiTxSsPtr->IsStreamToggled = FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a bridge unlocked has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_BrdgUnlockedCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_BRDG_UNLOCKED, 0);
+#endif
+
+  /* Check if user callback has been registered */
+  if (HdmiTxSsPtr->BrdgUnlockedCallback) {
+      HdmiTxSsPtr->BrdgUnlockedCallback(HdmiTxSsPtr->BrdgUnlockedRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a bridge Overflow has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_BrdgOverflowCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+  /* Check if user callback has been registered */
+  if (HdmiTxSsPtr->BrdgOverflowCallback) {
+      HdmiTxSsPtr->BrdgOverflowCallback(HdmiTxSsPtr->BrdgOverflowRef);
+  }
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a bridge Underflow has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_BrdgUnderflowCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+  /* Check if user callback has been registered */
+  if (HdmiTxSsPtr->BrdgUnderflowCallback) {
+      HdmiTxSsPtr->BrdgUnderflowCallback(HdmiTxSsPtr->BrdgUnderflowRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when a TX vsync has occurred.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_VsCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+  // Check if user callback has been registered
+  if (HdmiTxSsPtr->VsCallback) {
+      HdmiTxSsPtr->VsCallback(HdmiTxSsPtr->VsRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the TX stream is up.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_StreamUpCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+
+  /* Set stream up flag */
+  HdmiTxSsPtr->IsStreamUp = (TRUE);
+
+#ifdef USE_HDCP_TX
+  /* Push the stream-up event to the HDCP event queue */
+  XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_STREAMUP_EVT);
+#endif
+
+  /* Check if user callback has been registered.
+     User may change the video stream properties in the callback;
+     therefore, execute the callback before changing stream settings. */
+  if (HdmiTxSsPtr->StreamUpCallback) {
+      HdmiTxSsPtr->StreamUpCallback(HdmiTxSsPtr->StreamUpRef);
+  }
+
+  /* Set TX sample rate */
+  XV_HdmiTx_SetSampleRate(HdmiTxSsPtr->HdmiTxPtr, HdmiTxSsPtr->SamplingRate);
+
+  /* Release VID_IN bridge resets */
+  /* Linux - Remove the SYSRST deassert so that bridge is in reset */
+  XV_HdmiTxSs_VRST(HdmiTxSsPtr, FALSE);
+
+  /* Release HDMI TXCore resets */
+  XV_HdmiTxSs_TXCore_LRST(HdmiTxSsPtr, FALSE);
+  XV_HdmiTxSs_TXCore_VRST(HdmiTxSsPtr, FALSE);
+
+  if (HdmiTxSsPtr->VtcPtr) {
+    /* Setup VTC */
+    XV_HdmiTxSs_VtcSetup(HdmiTxSsPtr);
+  }
+
+  if (HdmiTxSsPtr->AudioEnabled) {
+      /* HDMI TX unmute audio */
+      HdmiTxSsPtr->AudioMute = (FALSE);
+      XV_HdmiTx_AudioEnable(HdmiTxSsPtr->HdmiTxPtr);
+  }
+
+  /* Configure video bridge mode according to HW setting and video format */
+  XV_HdmiTxSs_ConfigBridgeMode(HdmiTxSsPtr);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_STREAMUP, 0);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when the TX stream is down.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_StreamDownCallback(void *CallbackRef)
+{
+  XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)CallbackRef;
+  /* Assert HDMI TXCore link reset */
+  XV_HdmiTxSs_TXCore_LRST(HdmiTxSsPtr, TRUE);
+  XV_HdmiTxSs_TXCore_VRST(HdmiTxSsPtr, TRUE);
+
+  /* Assert SYSCLK VID_OUT bridge reset */
+  XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, TRUE);
+  XV_HdmiTxSs_VRST(HdmiTxSsPtr, TRUE);
+
+  /* Reset DDC */
+  XV_HdmiTx_DdcDisable(HdmiTxSsPtr->HdmiTxPtr);
+
+  /* Set stream up flag */
+  HdmiTxSsPtr->IsStreamUp = (FALSE);
+  HdmiTxSsPtr->DrmInfoframe.metadata_type = 0xff;
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_STREAMDOWN, 0);
+#endif
+#ifdef USE_HDCP_TX
+  /* Push the stream-down event to the HDCP event queue */
+  XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_STREAMDOWN_EVT);
+#endif
+
+  /* Check if user callback has been registered */
+  if (HdmiTxSsPtr->StreamDownCallback) {
+      HdmiTxSsPtr->StreamDownCallback(HdmiTxSsPtr->StreamDownRef);
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType                     Callback Function Type
+* -----------------------         ---------------------------------------------
+* (XV_HDMITXSS_HANDLER_CONNECT)       HpdCallback
+* (XV_HDMITXSS_HANDLER_VS)            VsCallback
+* (XV_HDMITXSS_HANDLER_STREAM_DOWN)   StreamDownCallback
+* (XV_HDMITXSS_HANDLER_STREAM_UP)     StreamUpCallback
+* (XV_HDMITXSS_HANDLER_BRDGOVERFLOW)  BrdgOverflowCallback
+* (XV_HDMITXSS_HANDLER_BRDGUNDERFLOW) BrdgUnderflowCallback
+* (XV_HDMITXSS_HANDLER_HDCP_AUTHENTICATED)
+* (XV_HDMITXSS_HANDLER_HDCP_DOWNSTREAM_TOPOLOGY_AVAILABLE)
+* (XV_HDMITXSS_HANDLER_HDCP_UNAUTHENTICATED)
+* </pre>
+*
+* @param    InstancePtr is a pointer to the HDMI TX Subsystem instance.
+* @param    HandlerType specifies the type of handler.
+* @param    CallbackFunc is the address of the callback function.
+* @param    CallbackRef is a user data item that will be passed to the
+*       callback function when it is invoked.
+*
+* @return
+*       - XST_SUCCESS if callback function installed successfully.
+*       - XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note     Invoking this function for a handler that already has been
+*       installed replaces it with the new handler.
+*
+******************************************************************************/
+int XV_HdmiTxSs_SetCallback(XV_HdmiTxSs *InstancePtr,
+		XV_HdmiTxSs_HandlerType HandlerType,
+		void *CallbackFunc,
+		void *CallbackRef)
+{
+    u32 Status;
+
+    /* Verify arguments. */
+    Xil_AssertNonvoid(InstancePtr != NULL);
+    Xil_AssertNonvoid(HandlerType >= (XV_HDMITXSS_HANDLER_CONNECT));
+    Xil_AssertNonvoid(CallbackFunc != NULL);
+    Xil_AssertNonvoid(CallbackRef != NULL);
+
+    /* Check for handler type */
+    switch (HandlerType) {
+        // Connect
+        case (XV_HDMITXSS_HANDLER_CONNECT):
+            InstancePtr->ConnectCallback = (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->ConnectRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Toggle
+        case (XV_HDMITXSS_HANDLER_TOGGLE):
+            InstancePtr->ToggleCallback = (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->ToggleRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Bridge Unlocked
+        case (XV_HDMITXSS_HANDLER_BRDGUNLOCK):
+            InstancePtr->BrdgUnlockedCallback =
+			    (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->BrdgUnlockedRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Bridge Overflow
+        case (XV_HDMITXSS_HANDLER_BRDGOVERFLOW):
+            InstancePtr->BrdgOverflowCallback =
+			    (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->BrdgOverflowRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Bridge Underflow
+        case (XV_HDMITXSS_HANDLER_BRDGUNDERFLOW):
+            InstancePtr->BrdgUnderflowCallback =
+			    (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->BrdgUnderflowRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Vsync
+        case (XV_HDMITXSS_HANDLER_VS):
+            InstancePtr->VsCallback = (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->VsRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream down
+        case (XV_HDMITXSS_HANDLER_STREAM_DOWN):
+            InstancePtr->StreamDownCallback =
+                (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->StreamDownRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // Stream up
+        case (XV_HDMITXSS_HANDLER_STREAM_UP):
+            InstancePtr->StreamUpCallback = (XV_HdmiTxSs_Callback)CallbackFunc;
+            InstancePtr->StreamUpRef = CallbackRef;
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP authenticated
+        case (XV_HDMITXSS_HANDLER_HDCP_AUTHENTICATED):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            /* Register HDCP 1.4 callbacks */
+            if (InstancePtr->Hdcp14Ptr) {
+              XHdcp1x_SetCallback(InstancePtr->Hdcp14Ptr,
+                                  XHDCP1X_HANDLER_AUTHENTICATED,
+								  (void *)(XHdcp1x_Callback) CallbackFunc,
+								  (void *)CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+            /* Register HDCP 2.2 callbacks */
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Tx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_TX_HANDLER_AUTHENTICATED,
+									(void *)(XHdcp22_Tx_Callback)CallbackFunc,
+									(void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP downstream topology available
+        case (XV_HDMITXSS_HANDLER_HDCP_DOWNSTREAM_TOPOLOGY_AVAILABLE):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            /** Register HDCP 1.4 callbacks */
+            if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetCallBack(InstancePtr->Hdcp14Ptr,
+                            (XHdcp1x_HandlerType) XHDCP1X_RPTR_HDLR_REPEATER_EXCHANGE,
+							(void *) (XHdcp1x_Callback)CallbackFunc,
+							(void *) CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+            /** Register HDCP 2.2 callbacks */
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Tx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_TX_HANDLER_DOWNSTREAM_TOPOLOGY_AVAILABLE,
+									(void *)(XHdcp22_Tx_Callback)CallbackFunc,
+									(void *)CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+            break;
+
+        // HDCP unauthenticated
+        case (XV_HDMITXSS_HANDLER_HDCP_UNAUTHENTICATED):
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+            /** Register HDCP 1.4 callbacks */
+            if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_SetCallBack(InstancePtr->Hdcp14Ptr,
+                            XHDCP1X_HANDLER_UNAUTHENTICATED,
+							(void *) (XHdcp1x_Callback)CallbackFunc,
+							(void *) CallbackRef);
+            }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+            /** Register HDCP 2.2 callbacks */
+            if (InstancePtr->Hdcp22Ptr) {
+              XHdcp22Tx_SetCallback(InstancePtr->Hdcp22Ptr,
+                                    XHDCP22_TX_HANDLER_UNAUTHENTICATED,
+                                    (void *) (XHdcp22_Tx_Callback)CallbackFunc,
+									(void *) CallbackRef);
+            }
+#endif
+            Status = (XST_SUCCESS);
+          break;
+
+        default:
+            Status = (XST_INVALID_PARAM);
+            break;
+    }
+
+    return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads the HDMI Sink EDID.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_ReadEdid(XV_HdmiTxSs *InstancePtr, u8 *Buffer)
+{
+    u32 Status;
+
+    // Default
+    Status = (XST_FAILURE);
+
+    // Check if a sink is connected
+    if (InstancePtr->IsStreamConnected == (TRUE)) {
+
+      *Buffer = 0x00;   // Offset zero
+      Status = XV_HdmiTx_DdcWrite(InstancePtr->HdmiTxPtr, 0x50, 1, Buffer,
+        (FALSE));
+
+      // Check if write was successful
+      if (Status == (XST_SUCCESS)) {
+        // Read edid
+        Status = XV_HdmiTx_DdcRead(InstancePtr->HdmiTxPtr, 0x50, 256, Buffer,
+            (TRUE));
+      }
+    }
+  return Status;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function reads one block from the HDMI Sink EDID.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_ReadEdidSegment(XV_HdmiTxSs *InstancePtr, u8 *Buffer, u8 segment)
+{
+    u32 Status;
+
+    u8 dummy = 0;
+
+    // Default
+    Status = (XST_FAILURE);
+
+    // Check if a sink is connected
+    if (InstancePtr->IsStreamConnected == (TRUE)) {
+
+	  // For multiple segment EDID read
+	  // First, read the first block, then read address 0x7e to know how many
+	  // blocks, if more than 2 blocks, then select segment after first 2 blocks
+	  // Use the following code to select segment
+
+	  if(segment != 0) {
+        // Segment Pointer
+        Status = XV_HdmiTx_DdcWrite(InstancePtr->HdmiTxPtr, 0x30, 1, &segment,
+        (FALSE));
+	  }
+
+      // Read blocks
+      dummy = 0x00;   // Offset zero
+      Status = XV_HdmiTx_DdcWrite(InstancePtr->HdmiTxPtr, 0x50, 1, &dummy,
+        (FALSE));
+
+      // Check if write was successful
+      if (Status == (XST_SUCCESS)) {
+        // Read edid
+        Status = XV_HdmiTx_DdcRead(InstancePtr->HdmiTxPtr, 0x50, 128, Buffer,
+            (TRUE));
+      }
+
+	  if(segment != 0) {
+        // Segment Pointer
+        Status = XV_HdmiTx_DdcWrite(InstancePtr->HdmiTxPtr, 0x30, 1, &segment,
+        (FALSE));
+	  }
+
+      // Read blocks
+      dummy = 0x80;   // Offset 128
+      Status = XV_HdmiTx_DdcWrite(InstancePtr->HdmiTxPtr, 0x50, 1, &dummy,
+        (FALSE));
+
+      // Check if write was successful
+      if (Status == (XST_SUCCESS)) {
+        // Read edid
+        Status = XV_HdmiTx_DdcRead(InstancePtr->HdmiTxPtr, 0x50, 128, &Buffer[128],
+            (TRUE));
+      }
+    }
+    else {
+      xil_printf("No sink is connected.\r\n");
+      xil_printf("Please connect a HDMI sink.\r\n");
+    }
+  return Status;
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function starts the HDMI TX stream
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_StreamStart(XV_HdmiTxSs *InstancePtr)
+{
+  u32 TmdsClk;
+
+  // Set TX pixel rate
+  XV_HdmiTx_SetPixelRate(InstancePtr->HdmiTxPtr);
+
+  // Set TX color depth
+  XV_HdmiTx_SetColorDepth(InstancePtr->HdmiTxPtr);
+
+  // Set TX color format
+  XV_HdmiTx_SetColorFormat(InstancePtr->HdmiTxPtr);
+
+  // Set the TMDS Clock
+  TmdsClk = XV_HdmiTxSS_SetTMDS(InstancePtr,
+				 InstancePtr->HdmiTxPtr->Stream.Video.VmId,
+				 InstancePtr->HdmiTxPtr->Stream.Video.ColorFormatId,
+				 InstancePtr->HdmiTxPtr->Stream.Video.ColorDepth);
+
+  // Set TX scrambler
+  XV_HdmiTx_Scrambler(InstancePtr->HdmiTxPtr);
+
+  // Set TX clock ratio
+  XV_HdmiTx_ClockRatio(InstancePtr->HdmiTxPtr);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_STREAMSTART, 0);
+#endif
+  if ((InstancePtr->HdmiTxPtr->Stream.IsHdmi20 == (FALSE))
+  		&& (TmdsClk > 340000000)) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "\r\nWarning: Sink does not support HDMI 2.0\r\n");
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "         Connect to HDMI 2.0 Sink or \r\n");
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "         Change to HDMI 1.4 video format\r\n\r\n");
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables / disables the TX scrambler
+*
+* @param  InstancePtr is a pointer to the Subsystem instance to be worked on.
+* @param  Enable TRUE:Enable scrambler FALSE:Disable scrambler
+*
+* @return None.
+*
+* @note   The scrambler setting will revert to the default behavior during the
+*         next stream configuration (scrambler is enabled for HDMI 2.0 video
+*         and disabled when the video is of HDMI 1.4 or lower)
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetScrambler(XV_HdmiTxSs *InstancePtr, u8 Enable)
+{
+	if (InstancePtr->HdmiTxPtr->Stream.IsHdmi20 == (TRUE)) {
+		/* Override the default behavior of the scrambler so that scrambling
+		 * can be disabled even when TMDS Clock > 340 MHz
+		 */
+		InstancePtr->HdmiTxPtr->Stream.OverrideScrambler = (TRUE);
+		/* Set the IsScrambled flag in order to enable or disable scrambler
+		 * when XV_HdmiTx_Scrambler is called
+		 */
+		XV_HdmiTxSs_SetVideoStreamScramblingFlag(InstancePtr, Enable);
+		/* Enable / disable scrambler depending on the value set to
+		 * IsScrambled
+		 */
+		XV_HdmiTx_Scrambler(InstancePtr->HdmiTxPtr);
+		// Disable the override of the scrambler
+		InstancePtr->HdmiTxPtr->Stream.OverrideScrambler = (FALSE);
+	} else {
+		xdbg_printf(XDBG_DEBUG_GENERAL,
+			  "\r\nWarning: Scrambler is always disabled when sink does"
+			  "not support SCDC control interface\r\n");
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sends audio info frames.
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SendAuxInfoframe(XV_HdmiTxSs *InstancePtr, void *Aux)
+{
+  u8 Index;
+  u8 Crc;
+  XHdmiC_Aux *tx_aux = (XHdmiC_Aux *)Aux;
+
+  if (Aux == (NULL)) {
+      /* Header, Packet type */
+      InstancePtr->HdmiTxPtr->Aux.Header.Byte[0] = 0x84;
+
+      /* Version */
+      InstancePtr->HdmiTxPtr->Aux.Header.Byte[1] = 0x01;
+
+      /* Length */
+      InstancePtr->HdmiTxPtr->Aux.Header.Byte[2] = 10;
+
+      /* Checksum (this will be calculated by the HDMI TX IP) */
+      InstancePtr->HdmiTxPtr->Aux.Header.Byte[3] = 0;
+
+      /* 2 Channel count. Audio coding type refer to stream */
+      InstancePtr->HdmiTxPtr->Aux.Data.Byte[1] = 0x1;
+
+      for (Index = 2; Index < 32; Index++) {
+        InstancePtr->HdmiTxPtr->Aux.Data.Byte[Index] = 0;
+      }
+
+      /* Calculate AVI infoframe checksum */
+      Crc = 0;
+
+      /* Header */
+      for (Index = 0; Index < 3; Index++) {
+        Crc += InstancePtr->HdmiTxPtr->Aux.Header.Byte[Index];
+      }
+
+      /* Data */
+      for (Index = 1; Index < 5; Index++) {
+        Crc += InstancePtr->HdmiTxPtr->Aux.Data.Byte[Index];
+      }
+
+      Crc = 256 - Crc;
+      InstancePtr->HdmiTxPtr->Aux.Data.Byte[0] = Crc;
+
+      XV_HdmiTx_AuxSend(InstancePtr->HdmiTxPtr);
+
+  }
+
+  else {
+      // Copy Audio Infoframe
+      if (tx_aux->Header.Byte[0] == 0x84) {
+        // Header
+        InstancePtr->HdmiTxPtr->Aux.Header.Data = tx_aux->Header.Data;
+
+        // Data
+        for (Index = 0; Index < 8; Index++) {
+          InstancePtr->HdmiTxPtr->Aux.Data.Data[Index] =
+            tx_aux->Data.Data[Index];
+        }
+      }
+  }
+
+  /* Send packet */
+  XV_HdmiTx_AuxSend(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sends generic info frames.
+*
+* @param  None.
+*
+* @return
+*       - XST_SUCCESS if infoframes transmitted successfully.
+*       - XST_FAILURE if AUX FIFO is full.
+*
+* @note   None.
+*
+******************************************************************************/
+u32 XV_HdmiTxSs_SendGenericAuxInfoframe(XV_HdmiTxSs *InstancePtr, void *Aux)
+{
+  u8 Index;
+  XHdmiC_Aux *tx_aux = (XHdmiC_Aux *)Aux;
+
+  // Header
+  InstancePtr->HdmiTxPtr->Aux.Header.Data = tx_aux->Header.Data;
+
+  // Data
+  for (Index = 0; Index < 8; Index++) {
+    InstancePtr->HdmiTxPtr->Aux.Data.Data[Index] =
+    tx_aux->Data.Data[Index];
+  }
+
+  /* Send packet */
+  return XV_HdmiTx_AuxSend(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS number of active audio channels
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  AudioChannels
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetAudioChannels(XV_HdmiTxSs *InstancePtr, u8 AudioChannels)
+{
+	// Audio InfoFrame's channel count starts from 2ch = 1
+	InstancePtr->AudioInfoframe.ChannelCount = AudioChannels - 1;
+    InstancePtr->AudioChannels = AudioChannels;
+    XV_HdmiTx_SetAudioChannels(InstancePtr->HdmiTxPtr, AudioChannels);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(InstancePtr,
+                         XV_HDMITXSS_LOG_EVT_SETAUDIOCHANNELS,
+                         AudioChannels);
+#endif
+}
+
+/*****************************************************************************/
+/**
+*
+* This function set HDMI TX audio parameters
+*
+* @param  Enable 0: Unmute the audio 1: Mute the audio.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_AudioMute(XV_HdmiTxSs *InstancePtr, u8 Enable)
+{
+  //Audio Mute Mode
+  if (Enable){
+	XV_HdmiTx_AudioDisable(InstancePtr->HdmiTxPtr);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_AUDIOMUTE, 0);
+#endif
+  }
+  else{
+	XV_HdmiTx_AudioEnable(InstancePtr->HdmiTxPtr);
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_AUDIOUNMUTE, 0);
+#endif
+  }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS Audio Format
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  format 1:HBR 0:L-PCM
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetAudioFormat(XV_HdmiTxSs *InstancePtr,
+		 XV_HdmiTx_AudioFormatType format)
+{
+    XV_HdmiTx_SetAudioFormat(InstancePtr->HdmiTxPtr, format);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the active audio format
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+*
+* @return   Active audio format of HDMI Tx Subsystem
+*
+* @note     None.
+*
+******************************************************************************/
+XV_HdmiTx_AudioFormatType XV_HdmiTxSs_GetAudioFormat(XV_HdmiTxSs *InstancePtr)
+{
+	XV_HdmiTx_AudioFormatType Format;
+
+	Format = XV_HdmiTx_GetAudioFormat(InstancePtr->HdmiTxPtr);
+
+    return Format;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI TX SS Aux structure
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return XVidC_VideoStream pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_Aux *XV_HdmiTxSs_GetAuxiliary(XV_HdmiTxSs *InstancePtr)
+{
+    return (&(InstancePtr->HdmiTxPtr->Aux));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI TX SS AVI InfoFrame structure
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return XHdmiC_AVI_InfoFrame pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_AVI_InfoFrame *XV_HdmiTxSs_GetAviInfoframe(XV_HdmiTxSs *InstancePtr)
+{
+    return (&(InstancePtr->AVIInfoframe));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI TX SS Audio InfoFrame structure
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return XHdmiC_AudioInfoFrame pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_AudioInfoFrame *XV_HdmiTxSs_GetAudioInfoframe(XV_HdmiTxSs *InstancePtr)
+{
+    return (&(InstancePtr->AudioInfoframe));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI TX SS Vendor Specific InfoFrame
+* structure
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return XHdmiC_VSIF pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XHdmiC_VSIF *XV_HdmiTxSs_GetVSIF(XV_HdmiTxSs *InstancePtr)
+{
+    return (&(InstancePtr->VSIF));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI TX SS DRM InfoFrame
+* structure
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return struct v4l2_hdr10_payload pointer
+*
+* @note   None.
+*
+******************************************************************************/
+struct v4l2_hdr10_payload *XV_HdmiTxSs_GetDrmInfoframe(XV_HdmiTxSs *InstancePtr)
+{
+    return (&(InstancePtr->DrmInfoframe));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function set HDMI TX susbsystem stream parameters
+*
+* @param  None.
+*
+* @return Calculated TMDS Clock
+*
+* @note   None.
+*
+******************************************************************************/
+u32 XV_HdmiTxSs_SetStream(XV_HdmiTxSs *InstancePtr,
+        XVidC_VideoMode VideoMode, XVidC_ColorFormat ColorFormat,
+        XVidC_ColorDepth Bpc, XVidC_3DInfo *Info3D)
+{
+  u32 TmdsClock = 0;
+
+  TmdsClock = XV_HdmiTx_SetStream(InstancePtr->HdmiTxPtr, VideoMode,
+    ColorFormat, Bpc, InstancePtr->Config.Ppc, Info3D);
+
+#ifdef XV_HDMITXSS_LOG_ENABLE
+  XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_SETSTREAM, VideoMode);
+#endif
+  if(TmdsClock == 0) {
+    xdbg_printf(XDBG_DEBUG_GENERAL,
+                "\r\nWarning: Sink does not support HDMI 2.0\r\n");
+    xdbg_printf(XDBG_DEBUG_GENERAL,
+                "         Connect to HDMI 2.0 Sink or \r\n");
+    xdbg_printf(XDBG_DEBUG_GENERAL,
+                "         Change to HDMI 1.4 video format\r\n\r\n");
+}
+
+  return TmdsClock;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function returns the pointer to HDMI TX SS video stream
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return XVidC_VideoStream pointer
+*
+* @note   None.
+*
+******************************************************************************/
+XVidC_VideoStream *XV_HdmiTxSs_GetVideoStream(XV_HdmiTxSs *InstancePtr)
+{
+    return (&InstancePtr->HdmiTxPtr->Stream.Video);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video stream
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param
+*
+* @return XVidC_VideoStream pointer
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetVideoStream(XV_HdmiTxSs *InstancePtr,
+                                    XVidC_VideoStream VidStream)
+{
+    // Set Stream Properties
+    InstancePtr->HdmiTxPtr->Stream.Video = VidStream;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video Identification code
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  SamplingRate Value
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetSamplingRate(XV_HdmiTxSs *InstancePtr, u8 SamplingRate)
+{
+    InstancePtr->SamplingRate = SamplingRate;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video Identification code
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  InstancePtr VIC Flag Value
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetVideoIDCode(XV_HdmiTxSs *InstancePtr, u8 Vic)
+{
+    InstancePtr->HdmiTxPtr->Stream.Vic = Vic;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video stream type
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  InstancePtr VIC Value 1:HDMI 0:DVI
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetVideoStreamType(XV_HdmiTxSs *InstancePtr, u8 StreamType)
+{
+    //InstancePtr->HdmiTxPtr->Stream.IsHdmi = StreamType;
+    if (StreamType) {
+    	XV_HdmiTxSS_SetHdmiMode(InstancePtr);
+    	XV_HdmiTxSs_AudioMute(InstancePtr, FALSE);
+    } else {
+    	XV_HdmiTxSs_AudioMute(InstancePtr, TRUE);
+    	XV_HdmiTxSS_SetDviMode(InstancePtr);
+    }
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video stream type
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  IsScrambled 1:IsScrambled 0: not Scrambled
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetVideoStreamScramblingFlag(XV_HdmiTxSs *InstancePtr,
+                                                            u8 IsScrambled)
+{
+    InstancePtr->HdmiTxPtr->Stream.IsScrambled = IsScrambled;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video stream scrambling behaviour. Setting
+* OverrideScramble to true will force enabling/disabling scrambling function
+* based on the value of IsScrambled flag.
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  OverrideScramble
+*         0: Scrambling is always enabled for HDMI 2.0 resolutions and is
+*            enabled /or disabled for HDMI 1.4 resolutions based on IsScrambled
+*            value
+*         1: Enable scrambling if IsScrambled is TRUE and disable scrambling
+*            if IsScrambled is FALSE
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetVideoStreamScramblingOverrideFlag(XV_HdmiTxSs *InstancePtr,
+                                                           u8 OverrideScramble)
+{
+    InstancePtr->HdmiTxPtr->Stream.OverrideScrambler = OverrideScramble;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS TMDS Cock Ratio
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param  Ratio 0 - 1/10, 1 - 1/40
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetTmdsClockRatio(XV_HdmiTxSs *InstancePtr, u8 Ratio)
+{
+    InstancePtr->HdmiTxPtr->Stream.TMDSClockRatio = Ratio;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function Sets the HDMI TX SS video Identification code
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param
+*
+* @return Stream Data Structure (TMDS Clock)
+*
+* @note   None.
+*
+******************************************************************************/
+u32 XV_HdmiTxSs_GetTmdsClockFreqHz(XV_HdmiTxSs *InstancePtr)
+{
+    return (InstancePtr->HdmiTxPtr->Stream.TMDSClock);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function detects connected sink is a HDMI 2.0/HDMI 1.4 sink device
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+*
+* @return
+*       - XST_SUCCESS if HDMI 2.0
+*       - XST_FAILURE if HDMI 1.4
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_DetectHdmi20(XV_HdmiTxSs *InstancePtr)
+{
+      return (XV_HdmiTx_DetectHdmi20(InstancePtr->HdmiTxPtr));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function is called when HDMI TX SS TMDS clock changes
+*
+* @param  None.
+*
+* @return None
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_RefClockChangeInit(XV_HdmiTxSs *InstancePtr)
+{
+
+      /* Assert VID_IN bridge resets */
+      XV_HdmiTxSs_SYSRST(InstancePtr, TRUE);
+      XV_HdmiTxSs_VRST(InstancePtr, TRUE);
+
+      /* Assert HDMI TXCore resets */
+      XV_HdmiTxSs_TXCore_LRST(InstancePtr, TRUE);
+      XV_HdmiTxSs_TXCore_VRST(InstancePtr, TRUE);
+
+      /* Clear variables */
+      XV_HdmiTx_Clear(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI TX SS timing information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_ReportTiming(XV_HdmiTxSs *InstancePtr)
+{
+      if (((u32) XV_HdmiTx_GetMode(InstancePtr->HdmiTxPtr)) == 0) {
+        xil_printf("HDMI TX Mode - DVI \r\n");
+      }
+      else {
+        xil_printf("HDMI TX Mode - HDMI \r\n");
+      }
+
+      if (XV_HdmiTxSS_IsMasked(InstancePtr) == 0) {
+	  xil_printf("HDMI Video Mask is Disabled\r\n\r\n");
+      }
+      else {
+	  xil_printf("HDMI Video Mask is Enabled\r\n\r\n");
+      }
+
+      XV_HdmiTx_DebugInfo(InstancePtr->HdmiTxPtr);
+      xil_printf("Scrambled: %0d\r\n",
+        (XV_HdmiTx_IsStreamScrambled(InstancePtr->HdmiTxPtr)));
+      xil_printf("Sample rate: %0d\r\n",
+        (XV_HdmiTx_GetSampleRate(InstancePtr->HdmiTxPtr)));
+      xil_printf("\r\n");
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI TX SS DRM If information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ReportDRMInfo(XV_HdmiTxSs *InstancePtr)
+{
+	struct v4l2_hdr10_payload *DrmInfoFramePtr;
+	DrmInfoFramePtr = XV_HdmiTxSs_GetDrmInfoframe(InstancePtr);
+
+	if (DrmInfoFramePtr->eotf != 0xFF)
+		xil_printf("eotf: %d\r\n", DrmInfoFramePtr->eotf);
+
+	if (DrmInfoFramePtr->metadata_type == 0xFF) {
+		xil_printf("No DRM info\r\n");
+		return;
+	}
+
+	xil_printf("DRM IF info:\r\n");
+	xil_printf("desc id: %d\r\n", DrmInfoFramePtr->metadata_type);
+	xil_printf("display primaries x0, y0, x1, y1, x2, y2: %d %d %d %d %d %d\r\n",
+			DrmInfoFramePtr->display_primaries[0].x, DrmInfoFramePtr->display_primaries[0].y,
+			DrmInfoFramePtr->display_primaries[1].x, DrmInfoFramePtr->display_primaries[1].y,
+			DrmInfoFramePtr->display_primaries[2].x, DrmInfoFramePtr->display_primaries[2].y
+		  );
+	xil_printf("white point x, y: %d %d\r\n",
+			DrmInfoFramePtr->white_point.x, DrmInfoFramePtr->white_point.y);
+	xil_printf("min/max display mastering luminance: %d %d\r\n",
+			DrmInfoFramePtr->min_mdl,
+			DrmInfoFramePtr->max_mdl);
+	xil_printf("Max_CLL: %d\r\n", DrmInfoFramePtr->max_cll);
+	xil_printf("max_fall: %d\r\n", DrmInfoFramePtr->max_fall);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI TX SS audio information
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ReportAudio(XV_HdmiTxSs *InstancePtr)
+{
+  xil_printf("Format   : ");
+  if (XV_HdmiTxSs_GetAudioFormat(InstancePtr) == 1) {
+	  xil_printf("HBR\r\n");
+  }
+  else {
+	  xil_printf("L-PCM\r\n");
+  }
+  xil_printf("Channels : %d\r\n",
+  XV_HdmiTx_GetAudioChannels(InstancePtr->HdmiTxPtr));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI TX SS subcore versions
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ReportSubcoreVersion(XV_HdmiTxSs *InstancePtr)
+{
+  u32 Data;
+
+  if (InstancePtr->HdmiTxPtr) {
+     Data = XV_HdmiTx_GetVersion(InstancePtr->HdmiTxPtr);
+     xil_printf("  HDMI TX version : %02d.%02d (%04x)\r\n",
+        ((Data >> 24) & 0xFF), ((Data >> 16) & 0xFF), (Data & 0xFFFF));
+  }
+
+  if (InstancePtr->VtcPtr){
+	 if (InstancePtr->IsStreamUp == TRUE){
+       Data = XVtc_GetVersion(InstancePtr->VtcPtr);
+       xil_printf("  VTC version     : %02d.%02d (%04x)\r\n",
+          ((Data >> 24) & 0xFF), ((Data >> 16) & 0xFF), (Data & 0xFFFF));
+	 }
+	 else {
+       xil_printf("  VTC version is not available for reading as ");
+	   xil_printf("HDMI TX Video Clock is not ready.\r\n");
+	 }
+  }
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  if (InstancePtr->Hdcp14Ptr){
+     Data = XHdcp1x_GetVersion(InstancePtr->Hdcp14Ptr);
+     xil_printf("  HDCP 1.4 TX version : %02d.%02d (%04x)\r\n",
+        ((Data >> 24) & 0xFF), ((Data >> 16) & 0xFF), (Data & 0xFFFF));
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  // HDCP 2.2
+  if (InstancePtr->Hdcp22Ptr) {
+   Data = XHdcp22Tx_GetVersion(InstancePtr->Hdcp22Ptr);
+   xil_printf("  HDCP 2.2 TX version : %02d.%02d (%04x)\r\n",
+    ((Data >> 24) & 0xFF), ((Data >> 16) & 0xFF), (Data & 0xFFFF));
+  }
+#endif
+
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI TX SS subcore versions
+*
+* @param  None.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_ReportInfo(XV_HdmiTxSs *InstancePtr)
+{
+    xil_printf("------------\r\n");
+    xil_printf("HDMI TX SubSystem\r\n");
+    xil_printf("------------\r\n");
+    XV_HdmiTxSs_ReportCoreInfo(InstancePtr);
+    XV_HdmiTxSs_ReportSubcoreVersion(InstancePtr);
+    xil_printf("\r\n");
+    xil_printf("HDMI TX timing\r\n");
+    xil_printf("------------\r\n");
+    XV_HdmiTxSs_ReportTiming(InstancePtr);
+    xil_printf("Audio\r\n");
+    xil_printf("---------\r\n");
+    XV_HdmiTxSs_ReportAudio(InstancePtr);
+    xil_printf("DRM info frame\r\n");
+    xil_printf("--------------\r\n");
+    XV_HdmiTxSs_ReportDRMInfo(InstancePtr);
+}
+/*****************************************************************************/
+/**
+*
+* This function checks if the video stream is up.
+*
+* @param  None.
+*
+* @return
+*   - TRUE if stream is up.
+*   - FALSE if stream is down.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_IsStreamUp(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify arguments. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  return (InstancePtr->IsStreamUp);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function checks if the interface is connected.
+*
+* @param  None.
+*
+* @return
+*   - TRUE if the interface is connected.
+*   - FALSE if the interface is not connected.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_IsStreamConnected(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify arguments. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  return (InstancePtr->IsStreamConnected);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function checks if the interface has toggled.
+*
+* @param  None.
+*
+* @return
+*   - TRUE if the interface HPD has toggled.
+*   - FALSE if the interface HPD has not toggled.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_IsStreamToggled(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify arguments. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  return (InstancePtr->IsStreamToggled);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function configures the Bridge for YUV420 and repeater functionality
+*
+* @param InstancePtr  Instance Pointer to the main data structure
+* @param None
+*
+* @return
+*
+* @note   None.
+*
+******************************************************************************/
+static void XV_HdmiTxSs_ConfigBridgeMode(XV_HdmiTxSs *InstancePtr) {
+	XVidC_VideoStream *HdmiTxSsVidStreamPtr;
+    HdmiTxSsVidStreamPtr = XV_HdmiTxSs_GetVideoStream(InstancePtr);
+
+    XHdmiC_AVI_InfoFrame *AviInfoFramePtr;
+    AviInfoFramePtr = XV_HdmiTxSs_GetAviInfoframe(InstancePtr);
+
+    // Pixel Repetition factor of 3 and above are not supported by the bridge
+    if (AviInfoFramePtr->PixelRepetition > XHDMIC_PIXEL_REPETITION_FACTOR_2) {
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    	XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_PIX_REPEAT_ERR,
+    			AviInfoFramePtr->PixelRepetition);
+#endif
+    	return;
+    }
+
+    if (HdmiTxSsVidStreamPtr->ColorFormatId == XVIDC_CSF_YCRCB_420) {
+        /*********************************************************
+         * 420 Support
+         *********************************************************/
+         XV_HdmiTxSs_BridgePixelRepeat(InstancePtr, FALSE);
+         AviInfoFramePtr->PixelRepetition = XHDMIC_PIXEL_REPETITION_FACTOR_1;
+         XV_HdmiTxSs_BridgeYuv420(InstancePtr, TRUE);
+    }
+    else {
+        if ((AviInfoFramePtr->PixelRepetition ==
+					XHDMIC_PIXEL_REPETITION_FACTOR_2))
+        {
+            /*********************************************************
+             * NTSC/PAL Support
+             *********************************************************/
+             XV_HdmiTxSs_BridgeYuv420(InstancePtr, FALSE);
+             XV_HdmiTxSs_BridgePixelRepeat(InstancePtr, TRUE);
+        }
+        else {
+            XV_HdmiTxSs_BridgeYuv420(InstancePtr, FALSE);
+            XV_HdmiTxSs_BridgePixelRepeat(InstancePtr, FALSE);
+            AviInfoFramePtr->PixelRepetition =
+					XHDMIC_PIXEL_REPETITION_FACTOR_1;
+        }
+    }
+}
+
+/*****************************************************************************/
+/**
+* This function will set the default in HDF.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param    Id is the XV_HdmiTxSs ID to operate on.
+*
+* @return   None.
+*
+* @note     Linux - No need to put definition inside.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetDefaultPpc(XV_HdmiTxSs *InstancePtr, u8 Id) {
+
+}
+
+/*****************************************************************************/
+/**
+* This function will set PPC specified by user.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param    Id is the XV_HdmiTxSs ID to operate on.
+* @param    Ppc is the PPC to be set.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_SetPpc(XV_HdmiTxSs *InstancePtr, u8 Id, u8 Ppc) {
+    InstancePtr->Config.Ppc = (XVidC_PixelsPerClock) Ppc;
+    Id = Id; //squash unused variable compiler warning
+}
+
+/*****************************************************************************/
+/**
+* This function will enable the video masking.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSS_MaskEnable(XV_HdmiTxSs *InstancePtr)
+{
+    XV_HdmiTx_MaskEnable(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+* This function will disable the video masking.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSS_MaskDisable(XV_HdmiTxSs *InstancePtr)
+{
+    XV_HdmiTx_MaskDisable(InstancePtr->HdmiTxPtr);
+}
+
+/*****************************************************************************/
+/**
+* This function will enable or disable the noise in the video mask.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	Enable specifies TRUE/FALSE value to either enable or disable the
+*		Noise.
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSS_MaskNoise(XV_HdmiTxSs *InstancePtr, u8 Enable)
+{
+    XV_HdmiTx_MaskNoise(InstancePtr->HdmiTxPtr, Enable);
+}
+
+static u32 XV_HdmiTxSS_GetVidMaskColorValue(XV_HdmiTxSs *InstancePtr,
+											u16 Value)
+{
+	u32 Data;
+	s8 Temp;
+
+	Temp = InstancePtr->Config.MaxBitsPerPixel -
+				InstancePtr->HdmiTxPtr->Stream.Video.ColorDepth;
+	Data = Value << ((Temp > 0) ? Temp : 0);
+
+	return Data;
+}
+
+/*****************************************************************************/
+/**
+* This function will set the red component in the video mask.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	Value specifies the video mask value set to red component
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSS_MaskSetRed(XV_HdmiTxSs *InstancePtr, u16 Value)
+{
+    u32 Data;
+
+    Data = XV_HdmiTxSS_GetVidMaskColorValue(InstancePtr, Value);
+
+	XV_HdmiTx_MaskSetRed(InstancePtr->HdmiTxPtr, (Data));
+}
+
+
+/*****************************************************************************/
+/**
+* This function will set the green component in the video mask.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	Value specifies the video mask value set to green component
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSS_MaskSetGreen(XV_HdmiTxSs *InstancePtr, u16 Value)
+{
+    u32 Data;
+
+    Data = XV_HdmiTxSS_GetVidMaskColorValue(InstancePtr, Value);
+
+	XV_HdmiTx_MaskSetGreen(InstancePtr->HdmiTxPtr, (Data));
+}
+
+/*****************************************************************************/
+/**
+* This function will set the blue component in the video mask.
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	Value specifies the video mask value set to blue component
+*
+* @return   None.
+*
+* @note     None.
+*
+******************************************************************************/
+void XV_HdmiTxSS_MaskSetBlue(XV_HdmiTxSs *InstancePtr, u16 Value)
+{
+    u32 Data;
+
+    Data = XV_HdmiTxSS_GetVidMaskColorValue(InstancePtr, Value);
+
+	XV_HdmiTx_MaskSetBlue(InstancePtr->HdmiTxPtr, (Data));
+}
+
+/*****************************************************************************/
+/**
+* This function configures the background color for Video Masking Feature
+*
+* @param  InstancePtr is a pointer to the core instance to be worked on.
+* @param  ColorId is the background color requested
+*
+* @return None
+*
+******************************************************************************/
+void XV_HdmiTxSS_SetBackgroundColor(XV_HdmiTxSs *InstancePtr,
+                                    XVMaskColorId  ColorId)
+{
+    u16 Cr_R_val,y_G_val,Cb_B_val;
+    u16 scale;
+
+    XVidC_ColorFormat cfmt;
+	XVidC_ColorDepth bpc;
+
+    XVidC_VideoStream *HdmiTxSsVidStreamPtr;
+    HdmiTxSsVidStreamPtr = XV_HdmiTxSs_GetVideoStream(InstancePtr);
+
+    cfmt = HdmiTxSsVidStreamPtr->ColorFormatId;
+	bpc = InstancePtr->HdmiTxPtr->Stream.Video.ColorDepth;
+
+  /*
+   * Assert validates the input arguments
+   */
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  if(cfmt == XVIDC_CSF_RGB)
+  {
+    scale = ((1<<bpc)-1);
+    y_G_val  = bkgndColorRGB[ColorId][0] * scale;
+    Cb_B_val = bkgndColorRGB[ColorId][1] * scale;
+    Cr_R_val = bkgndColorRGB[ColorId][2] * scale;
+  }
+  else //YUV
+  {
+    scale =  (1<<(bpc-XVIDC_BPC_8));
+    y_G_val  = bkgndColorYUV[ColorId][0] * scale;
+    Cb_B_val = bkgndColorYUV[ColorId][1] * scale;
+    Cr_R_val = bkgndColorYUV[ColorId][2] * scale;
+  }
+
+  if(ColorId == XV_BKGND_NOISE) {
+	XV_HdmiTxSS_MaskNoise(InstancePtr, (TRUE));
+  }
+  else {
+	XV_HdmiTxSS_MaskNoise(InstancePtr, (FALSE));
+    /* Set Background color (outside window) */
+	XV_HdmiTxSS_MaskSetRed(InstancePtr,  Cr_R_val);
+	XV_HdmiTxSS_MaskSetGreen(InstancePtr, y_G_val);
+	XV_HdmiTxSS_MaskSetBlue(InstancePtr, Cb_B_val);
+  }
+  XV_HdmiTxSS_MaskEnable(InstancePtr);
+}
+
+
+/*****************************************************************************/
+/**
+* This function will get the current video mask mode
+*
+* @param    InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+*
+* @return   Current mode.
+*       0 = Video masking is disabled
+*       1 = Video masking is enabled
+*
+* @note     None.
+*
+*
+******************************************************************************/
+u8 XV_HdmiTxSS_IsMasked(XV_HdmiTxSs *InstancePtr)
+{
+    return ((u8)XV_HdmiTx_IsMasked(InstancePtr->HdmiTxPtr));
+}
+
+/*****************************************************************************/
+/**
+*
+* This function prints the HDMI TX SS information to passed buffer
+*
+* @param	InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	buff Buffer to print to
+* @param	buff_size size off buff passed
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_ShowInfo(XV_HdmiTxSs *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+	struct v4l2_hdr10_payload *DrmInfoFramePtr =
+				XV_HdmiTxSs_GetDrmInfoframe(InstancePtr);
+
+	strSize = scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nTx Info\r\n" \
+				"--------\r\n");
+    if (((u32) XV_HdmiTx_GetMode(InstancePtr->HdmiTxPtr)) == 0) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+	        "TX Mode - DVI \r\n");
+    } else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"TX Mode - HDMI \r\n");
+    }
+
+    if (XV_HdmiTxSS_IsMasked(InstancePtr) == 0) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"HDMI Video Mask is Disabled\r\n\r\n");
+    } else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"HDMI Video Mask is Enabled\r\n\r\n");
+    }
+
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"Scrambled: %0d\r\n",
+			(XV_HdmiTx_IsStreamScrambled(InstancePtr->HdmiTxPtr)));
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"Sample rate: %0d\r\n",
+			(XV_HdmiTx_GetSampleRate(InstancePtr->HdmiTxPtr)));
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"Audio channels: %0d\r\n\r\n",
+			(XV_HdmiTx_GetAudioChannels(InstancePtr->HdmiTxPtr)));
+
+	if (DrmInfoFramePtr->eotf != 0xFF) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"eotf: %d\r\n", DrmInfoFramePtr->eotf);
+	}
+
+	if (DrmInfoFramePtr->metadata_type == 0xFF) {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nNo DRM info\r\n");
+	} else {
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"\r\nDRM IF Info\r\n" \
+				"------------\r\n");
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"desc id: %d\r\n", DrmInfoFramePtr->metadata_type);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"display primaries x0, y0, x1, y1, x2, y2: %d %d %d %d %d %d\r\n",
+				DrmInfoFramePtr->display_primaries[0].x, DrmInfoFramePtr->display_primaries[0].y,
+				DrmInfoFramePtr->display_primaries[1].x, DrmInfoFramePtr->display_primaries[1].y,
+				DrmInfoFramePtr->display_primaries[2].x, DrmInfoFramePtr->display_primaries[2].y);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"white point x, y: %d %d\r\n",
+				DrmInfoFramePtr->white_point.x, DrmInfoFramePtr->white_point.y);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"min/max display mastering luminance: %d %d\r\n",
+				DrmInfoFramePtr->min_mdl,
+				DrmInfoFramePtr->max_mdl);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"max_cll: %d\r\n", DrmInfoFramePtr->max_cll);
+		strSize += scnprintf(buff+strSize, buff_size-strSize,
+				"max_fall: %d\r\n", DrmInfoFramePtr->max_fall);
+	}
+
+  return strSize;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss.h
@@ -0,0 +1,593 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitxss.h
+*
+* This is main header file of the Xilinx HDMI TX Subsystem driver
+*
+* <b>HDMI Transmitter Subsystem Overview</b>
+*
+* HDMI TX Subsystem is a collection of IP cores bounded together by software
+* to provide an abstract view of the processing pipe. It hides all the
+* complexities of programming the underlying cores from end user.
+*
+* <b>Subsystem Driver Features</b>
+*
+* HDMI Subsystem supports following features
+*   - AXI Stream Input/Output interface
+*   - 1, 2 or 4 pixel-wide video interface
+*   - 8/10/12/16 bits per component
+*   - RGB & YCbCr color space
+*   - Up to 4k2k 60Hz resolution at both Input and Output interface
+*   - Interlaced input support (1080i 50Hz/60Hz)
+
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     15/01/16 Add 3D Support
+* 1.2   yh     20/01/16 Added remapper support
+* 1.3   yh     01/02/16 Added set_ppc api
+* 1.4   MG     03/02/16 Added HDCP support
+* 1.5   MG     09/03/16 Removed reduced blanking support and
+*                       added XV_HdmiTxSS_SetHdmiMode and XV_HdmiTxSS_SetDviMode
+* 1.6   MH     03/15/16 Added HDCP connect event
+* 1.7   YH     17/03/16 Remove xintc.h as it is processor dependent
+* 1.8   YH     18/03/16 Add XV_HdmiTxSs_SendGenericAuxInfoframe function
+* 1.9   MH     23/06/16 Added HDCP repeater support.
+* 1.10  YH     25/07/16 Used UINTPTR instead of u32 for BaseAddress
+* 1.11  MH     08/08/16 Updates to optimize out HDCP when excluded.
+* 1.12  YH     18/08/16 Combine Report function into one ReportInfo
+*                       Add Event Log
+* 1.13  YH     27/08/16 Remove unused function XV_HdmiTxSs_SetUserTimerHandler
+* 1.14  YH     14/11/16 Added API to enable/disable YUV420/Pixel Repeat Mode
+*                       for video bridge
+* 1.15  YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.16  mmo    03/01/17 Add compiler option(XV_HDMITXSS_LOG_ENABLE) to enable
+*                            Log
+*                       Re-order the enumation and data structure
+* 1.17  mmo    02/03/17 Added XV_HdmiTxSs_ReadEdidSegment API for Multiple
+*                             Segment Support and HDMI Compliance Test
+* 4.0   YH     19/07/17 Added Video Masking APIs
+*       MH     09/08/17 Added function XV_HdmiTxSs_HdcpSetCapability
+*              22/08/17 Added function XV_HdmiTxSs_SetAudioFormat
+*       EB     10/10/17 Added function XV_HdmiTxSs_GetAudioFormat
+* 5.0   YH     16/01/18 Added dedicated reset for each clock domain
+*                       Added bridge unlock interrupt
+*                       Added PIO_OUT to set GCP_AVMUTE
+*       EB     17/01/18 Added InfoFrame data structure to XV_HdmiTxSs
+*                       Added XV_HDMITXSS_LOG_EVT_PIX_REPEAT_ERR log event
+*                       Added functions XV_HdmiTxSs_GetAuxiliary,
+*                             XV_HdmiTxSs_GetAviInfoframe,
+*                             XV_HdmiTxSs_GetAudioInfoframe,
+*                             XV_HdmiTxSs_GetVSIF
+*                       Updated the return type of the function
+*                             XV_HdmiTxSs_SendGenericAuxInfoframe
+*       EB     23/01/18 Added function
+*                           XV_HdmiTxSs_SetVideoStreamHdmi14ScramblingOverrideFlag
+*              25/01/18 Added function XV_HdmiTxSs_SetScrambler
+*       mmo    08/02/18 Added LowResolutionSupp & YUV420Supp in the
+*                             XV_HdmiTxSs_Config
+*       SM     28/02/18 Added XV_HdmiTxSS_SetAppVersion API and AppMajVer and
+*                           AppMinVer version number in XV_HdmiTxSs structure
+*       MMO    11/08/18 Added Bridge Overflow and Bridge Underflow Interrupt
+* </pre>
+*
+******************************************************************************/
+
+#ifndef HDMITXSS_H /**< prevent circular inclusions by using protection macros*/
+#define HDMITXSS_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+#include "xstatus.h"
+#include "xvidc.h"
+#include "xv_hdmic.h"
+#include "xv_hdmic_vsif.h"
+
+#include "xv_hdmitx.h"
+#include "xvtc.h"
+
+#if !defined(XV_CONFIG_LOG_VHDMITXSS_DISABLE) && \
+                                             !defined(XV_CONFIG_LOG_DISABLE_ALL)
+#define XV_HDMITXSS_LOG_ENABLE
+#endif
+
+#if defined(XPAR_XHDCP_NUM_INSTANCES) || defined(XPAR_XHDCP22_TX_NUM_INSTANCES)
+#define USE_HDCP_TX
+#define XV_HDMITXSS_HDCP_KEYSEL 0x00u
+#define XV_HDMITXSS_HDCP_MAX_QUEUE_SIZE 16
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+#include "xtmrctr.h"
+#include "xhdcp1x.h"
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+#include "xhdcp22_tx.h"
+#endif
+
+
+
+/****************************** Type Definitions ******************************/
+#define ANSI_COLOR_RED     "\x1b[31m"
+#define ANSI_COLOR_YELLOW  "\x1b[33m"
+#define ANSI_COLOR_RESET   "\x1b[0m"
+
+/**
+ * This typedef contains the different background colors available
+ */
+typedef enum
+{
+  XV_BKGND_BLACK = 0,
+  XV_BKGND_WHITE,
+  XV_BKGND_RED,
+  XV_BKGND_GREEN,
+  XV_BKGND_BLUE,
+  XV_BKGND_NOISE,
+  XV_BKGND_LAST
+}XVMaskColorId;
+
+/** @name Handler Types
+* @{
+*/
+#ifdef XV_HDMITXSS_LOG_ENABLE
+typedef enum {
+	XV_HDMITXSS_LOG_EVT_NONE = 1,		  /**< Log event none. */
+	XV_HDMITXSS_LOG_EVT_HDMITX_INIT,	  /**< Log event HDMITX Init. */
+	XV_HDMITXSS_LOG_EVT_VTC_INIT,	      /**< Log event VTC Init. */
+	XV_HDMITXSS_LOG_EVT_HDCPTIMER_INIT,	  /**< Log event HDCP Timer Init */
+	XV_HDMITXSS_LOG_EVT_HDCP14_INIT,	  /**< Log event HDCP 14 Init. */
+	XV_HDMITXSS_LOG_EVT_HDCP22_INIT,	  /**< Log event HDCP 22 Init. */
+	XV_HDMITXSS_LOG_EVT_REMAP_HWRESET_INIT,	/**< Log event Remap reset Init. */
+	XV_HDMITXSS_LOG_EVT_REMAP_INIT,		/**< Log event Remapper Init. */
+	XV_HDMITXSS_LOG_EVT_START,	/**< Log event HDMITXSS Start. */
+	XV_HDMITXSS_LOG_EVT_STOP,	/**< Log event HDMITXSS Stop. */
+	XV_HDMITXSS_LOG_EVT_RESET,	/**< Log event HDMITXSS Reset. */
+	XV_HDMITXSS_LOG_EVT_CONNECT, /**< Log event Cable connect. */
+	XV_HDMITXSS_LOG_EVT_TOGGLE, /**< Log event HPD toggle. */
+	XV_HDMITXSS_LOG_EVT_DISCONNECT,	/**< Log event Cable disconnect. */
+	XV_HDMITXSS_LOG_EVT_STREAMUP,	/**< Log event Stream Up. */
+	XV_HDMITXSS_LOG_EVT_STREAMDOWN,	/**< Log event Stream Down. */
+	XV_HDMITXSS_LOG_EVT_STREAMSTART, /**< Log event Stream Start. */
+	XV_HDMITXSS_LOG_EVT_SETAUDIOCHANNELS, /**< Log event Set Audio Channels. */
+	XV_HDMITXSS_LOG_EVT_AUDIOMUTE,		/**< Log event Audio Mute */
+	XV_HDMITXSS_LOG_EVT_AUDIOUNMUTE,	/**< Log event Audio Unmute. */
+	XV_HDMITXSS_LOG_EVT_SETSTREAM,   /**< Log event HDMITXSS Setstream. */
+	XV_HDMITXSS_LOG_EVT_HDCP14_AUTHREQ,   /**< Log event HDCP 1.4 AuthReq. */
+	XV_HDMITXSS_LOG_EVT_HDCP22_AUTHREQ,   /**< Log event HDCP 2.2 AuthReq. */
+	XV_HDMITXSS_LOG_EVT_PIX_REPEAT_ERR,	/**< Log event Unsupported Pixel
+											 Repetition. */
+	XV_HDMITXSS_LOG_EVT_VTC_RES_ERR,	/**< Log event Resolution Unsupported
+											 by VTC. */
+	XV_HDMITXSS_LOG_EVT_BRDG_UNLOCKED,	/**< VID-OUT bridge unlocked. */
+	XV_HDMITXSS_LOG_EVT_DUMMY		/**< Dummy Event should be last */
+} XV_HdmiTxSs_LogEvent;
+
+/**
+ * This typedef contains the logging mechanism for debug.
+ */
+typedef struct {
+    u16 DataBuffer[256];        /**< Log buffer with event data. */
+    u8 HeadIndex;               /**< Index of the head entry of the
+                                     Event/DataBuffer. */
+    u8 TailIndex;               /**< Index of the tail entry of the
+                                     Event/DataBuffer. */
+} XV_HdmiTxSs_Log;
+#endif
+
+/**
+* These constants specify the HDCP protection schemes
+*/
+typedef enum
+{
+    XV_HDMITXSS_HDCP_NONE,   /**< No content protection */
+    XV_HDMITXSS_HDCP_14,     /**< HDCP 1.4 */
+    XV_HDMITXSS_HDCP_22,     /**< HDCP 2.2 */
+    XV_HDMITXSS_HDCP_BOTH    /**< Both HDCP 1.4 and 2.2 */
+} XV_HdmiTxSs_HdcpProtocol;
+
+#ifdef USE_HDCP_TX
+/**
+* These constants specify the HDCP key types
+*/
+typedef enum
+{
+    XV_HDMITXSS_KEY_HDCP22_LC128,   /**< HDCP 2.2 LC128 */
+    XV_HDMITXSS_KEY_HDCP22_SRM,     /**< HDCP 2.2 SRM */
+    XV_HDMITXSS_KEY_HDCP14,         /**< HDCP 1.4 Key */
+    XV_HDMITXSS_KEY_HDCP14_SRM,     /**< HDCP 1.4 SRM */
+    XV_HDMITXSS_KEY_INVALID         /**< Invalid Key */
+} XV_HdmiTxSs_HdcpKeyType;
+
+/**
+* These constants specify HDCP repeater content stream management type
+*/
+typedef enum
+{
+    XV_HDMITXSS_HDCP_STREAMTYPE_0, /**< HDCP Stream Type 0 */
+    XV_HDMITXSS_HDCP_STREAMTYPE_1  /**< HDCP Stream Type 1 */
+} XV_HdmiTxSs_HdcpContentStreamType;
+
+typedef enum
+{
+    XV_HDMITXSS_HDCP_NO_EVT,
+    XV_HDMITXSS_HDCP_STREAMUP_EVT,
+    XV_HDMITXSS_HDCP_STREAMDOWN_EVT,
+    XV_HDMITXSS_HDCP_CONNECT_EVT,
+    XV_HDMITXSS_HDCP_DISCONNECT_EVT,
+    XV_HDMITXSS_HDCP_AUTHENTICATE_EVT,
+    XV_HDMITXSS_HDCP_INVALID_EVT
+} XV_HdmiTxSs_HdcpEvent;
+
+/**
+* These constants are used to identify fields inside the topology structure
+*/
+typedef enum {
+    XV_HDMITXSS_HDCP_TOPOLOGY_DEPTH,
+    XV_HDMITXSS_HDCP_TOPOLOGY_DEVICECNT,
+    XV_HDMITXSS_HDCP_TOPOLOGY_MAXDEVSEXCEEDED,
+    XV_HDMITXSS_HDCP_TOPOLOGY_MAXCASCADEEXCEEDED,
+    XV_HDMITXSS_HDCP_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM,
+    XV_HDMITXSS_HDCP_TOPOLOGY_HDCP1DEVICEDOWNSTREAM,
+    XV_HDMITXSS_HDCP_TOPOLOGY_INVALID
+} XV_HdmiTxSs_HdcpTopologyField;
+
+typedef struct
+{
+    XV_HdmiTxSs_HdcpEvent   Queue[XV_HDMITXSS_HDCP_MAX_QUEUE_SIZE]; /**< Data */
+    u8                      Tail;      /**< Tail pointer */
+    u8                      Head;      /**< Head pointer */
+} XV_HdmiTxSs_HdcpEventQueue;
+#endif
+
+/**
+* These constants specify different types of handler and used to differentiate
+* interrupt requests from peripheral.
+*/
+typedef enum {
+    XV_HDMITXSS_HANDLER_CONNECT = 1,                       /**< Handler for
+                                                            connect event */
+    XV_HDMITXSS_HANDLER_TOGGLE,                            /**< Handler for
+                                                            toggle event */
+    XV_HDMITXSS_HANDLER_BRDGUNLOCK,                        /**< Handler for
+                                                            bridge unlocked
+                                                            event */
+    XV_HDMITXSS_HANDLER_BRDGOVERFLOW,                      /**< Handler for
+                                                            bridge overflow
+                                                            event */
+    XV_HDMITXSS_HANDLER_BRDGUNDERFLOW,                     /**< Handler for
+                                                            bridge underflow
+                                                            event */
+    XV_HDMITXSS_HANDLER_VS,                                /**< Handler for
+                                                            vsync event */
+    XV_HDMITXSS_HANDLER_STREAM_DOWN,                       /**< Handler for
+                                                            stream down event */
+    XV_HDMITXSS_HANDLER_STREAM_UP,                         /**< Handler for
+                                                            stream up event */
+    XV_HDMITXSS_HANDLER_HDCP_AUTHENTICATED,                /**< Handler for
+                                                            HDCP authenticated
+                                                            event */
+    XV_HDMITXSS_HANDLER_HDCP_DOWNSTREAM_TOPOLOGY_AVAILABLE,/**< Handler for
+                                                            HDCP downstream
+                                                            topology available
+                                                            event */
+    XV_HDMITXSS_HANDLER_HDCP_UNAUTHENTICATED               /**< Handler for
+                                                            HDCP unauthenticated
+                                                            event */
+} XV_HdmiTxSs_HandlerType;
+/*@}*/
+
+/**
+ * Sub-Core Configuration Table
+ */
+typedef struct
+{
+  u16 IsPresent;  /**< Flag to indicate if sub-core is present in the design*/
+  u16 DeviceId;   /**< Device ID of the sub-core */
+  UINTPTR AbsAddr; /**< Sub-core Absolute Base Address */
+}XV_HdmiTxSs_SubCore;
+
+/**
+ * Video Processing Subsystem configuration structure.
+ * Each subsystem device should have a configuration structure associated
+ * that defines the MAX supported sub-cores within subsystem
+ */
+
+typedef struct
+{
+    u16 DeviceId;                     /**< DeviceId is the unique ID  of the
+                                           device */
+    UINTPTR BaseAddress;              /**< BaseAddress is the physical base
+                                           address of the subsystem address
+                                           range */
+    UINTPTR HighAddress;              /**< HighAddress is the physical MAX
+                                           address of the subsystem address
+                                           range */
+    XVidC_PixelsPerClock Ppc;         /**< Supported Pixel per Clock */
+    u8 MaxBitsPerPixel;               /**< Maximum  Supported Color Depth */
+	u8 LowResolutionSupp;
+	u8 YUV420Supp;
+    u32 AxiLiteClkFreq;               /**< AXI Lite Clock Frequency in Hz */
+    XV_HdmiTxSs_SubCore HdcpTimer;    /**< Sub-core instance configuration */
+    XV_HdmiTxSs_SubCore Hdcp14;       /**< Sub-core instance configuration */
+    XV_HdmiTxSs_SubCore Hdcp22;       /**< Sub-core instance configuration */
+    XV_HdmiTxSs_SubCore HdmiTx;       /**< Sub-core instance configuration */
+    XV_HdmiTxSs_SubCore Vtc;          /**< Sub-core instance configuration */
+} XV_HdmiTxSs_Config;
+
+/**
+* Callback type for interrupt.
+*
+* @param  CallbackRef is a callback reference passed in by the upper
+*   layer when setting the callback functions, and passed back to
+*   the upper layer when the callback is invoked.
+*
+* @return None.
+*
+* @note   None.
+*
+*/
+typedef void (*XV_HdmiTxSs_Callback)(void *CallbackRef);
+
+/**
+* The XVprocss driver instance data. The user is required to allocate a variable
+* of this type for every XVprocss device in the system. A pointer to a variable
+* of this type is then passed to the driver API functions.
+*/
+typedef struct
+{
+    XV_HdmiTxSs_Config Config;  /**< Hardware configuration */
+    u32 IsReady;         /**< Device and the driver instance are initialized */
+
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_Log Log;                /**< A log of events. */
+#endif
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    XTmrCtr *HdcpTimerPtr;          /**< handle to sub-core driver instance */
+    XHdcp1x *Hdcp14Ptr;             /**< handle to sub-core driver instance */
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    XHdcp22_Tx  *Hdcp22Ptr;         /**< handle to sub-core driver instance */
+#endif
+    XV_HdmiTx *HdmiTxPtr;           /**< handle to sub-core driver instance */
+    XVtc *VtcPtr;                   /**< handle to sub-core driver instance */
+
+    /* Callbacks */
+    XV_HdmiTxSs_Callback ConnectCallback; /**< Callback for connect event */
+    void *ConnectRef;                     /**< To be passed to the connect
+                                               callback */
+
+    XV_HdmiTxSs_Callback ToggleCallback; /**< Callback for toggle event */
+    void *ToggleRef;                     /**< To be passed to the toggle
+                                              callback */
+
+    XV_HdmiTxSs_Callback BrdgUnlockedCallback; /**< Callback for Bridge
+                                                 * UnLocked event interrupt */
+    void *BrdgUnlockedRef;                  /**< To be passed to the Bridge
+                                              Unlocked interrupt callback */
+
+    XV_HdmiTxSs_Callback BrdgOverflowCallback; /**< Callback for Bridge
+                                                 * Overflow event interrupt */
+    void *BrdgOverflowRef;                  /**< To be passed to the Bridge
+                                              Overflow interrupt callback */
+
+    XV_HdmiTxSs_Callback BrdgUnderflowCallback; /**< Callback for Bridge
+                                                 * Underflow event interrupt */
+    void *BrdgUnderflowRef;                  /**< To be passed to the Bridge
+                                              Underflow interrupt callback */
+
+    XV_HdmiTxSs_Callback VsCallback; /**< Callback for Vsync event */
+    void *VsRef;                   /**< To be passed to the Vsync callback */
+
+    XV_HdmiTxSs_Callback StreamDownCallback; /**< Callback for stream down */
+    void *StreamDownRef; /**< To be passed to the stream down callback */
+
+    XV_HdmiTxSs_Callback StreamUpCallback; /**< Callback for stream up */
+    void *StreamUpRef;  /**< To be passed to the stream up callback */
+
+    /**< Scratch pad */
+    u8 SamplingRate;              /**< HDMI TX Sampling rate */
+    u8 IsStreamConnected;         /**< HDMI TX Stream Connected */
+    u8 IsStreamUp;                /**< HDMI TX Stream Up */
+    u8 IsStreamToggled;           /**< HDMI TX Stream Toggled */
+    u8 AudioEnabled;              /**< HDMI TX Audio Enabled */
+    u8 AudioMute;                 /**< HDMI TX Audio Mute */
+    u8 AudioChannels;             /**< Number of Audio Channels */
+
+	XHdmiC_AVI_InfoFrame AVIInfoframe;		/**< AVI InfoFrame */
+	XHdmiC_AudioInfoFrame AudioInfoframe;	/**< Audio InfoFrame */
+	XHdmiC_VSIF VSIF;						/**< Vendor Specific InfoFrame */
+	struct v4l2_hdr10_payload DrmInfoframe;	/**< DRM Infoframe */
+
+    XV_HdmiTxSs_HdcpProtocol    HdcpProtocol;    /**< HDCP protocol selected */
+#ifdef USE_HDCP_TX
+    /**< HDCP specific */
+    XV_HdmiTxSs_HdcpProtocol    HdcpCapability;  /**< HDCP protocol desired */
+    u32                         HdcpIsReady;     /**< HDCP ready flag */
+    XV_HdmiTxSs_HdcpEventQueue  HdcpEventQueue;  /**< HDCP event queue */
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    u8                          *Hdcp22Lc128Ptr; /**< Pointer to HDCP 2.2
+                                                      LC128 */
+    u8                          *Hdcp22SrmPtr;   /**< Pointer to HDCP 2.2 SRM */
+#endif
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    u8                          *Hdcp14KeyPtr;   /**< Pointer to HDCP 1.4 key */
+    u8                          *Hdcp14SrmPtr;   /**< Pointer to HDCP 1.4 SRM */
+#endif
+#endif
+} XV_HdmiTxSs;
+
+/************************** Macros Definitions *******************************/
+#ifdef USE_HDCP_TX
+#define XV_HdmiTxSs_HdcpIsReady(InstancePtr) \
+  (InstancePtr)->HdcpIsReady
+#endif
+/************************** Function Prototypes ******************************/
+XV_HdmiTxSs_Config *XV_HdmiTxSs_LookupConfig(u32 DeviceId);
+void XV_HdmiTxSS_SetHdmiMode(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSS_SetDviMode(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSS_HdmiTxIntrHandler(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_CfgInitialize(XV_HdmiTxSs *InstancePtr,
+    XV_HdmiTxSs_Config *CfgPtr,
+    UINTPTR EffectiveAddr);
+int XV_HdmiTxSs_CfgInitializeHdcp(XV_HdmiTxSs *InstancePtr,
+    XV_HdmiTxSs_Config *CfgPtr,
+    UINTPTR EffectiveAddr);
+void XV_HdmiTxSs_Start(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_Stop(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_Reset(XV_HdmiTxSs *InstancePtr);
+
+void XV_HdmiTxSs_TXCore_VRST(XV_HdmiTxSs *InstancePtr, u8 Reset);
+void XV_HdmiTxSs_TXCore_LRST(XV_HdmiTxSs *InstancePtr, u8 Reset);
+void XV_HdmiTxSs_VRST(XV_HdmiTxSs *InstancePtr, u8 Reset);
+void XV_HdmiTxSs_SYSRST(XV_HdmiTxSs *InstancePtr, u8 Reset);
+void XV_HdmiTxSs_SetGcpAvmuteBit(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_ClearGcpAvmuteBit(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_SetGcpClearAvmuteBit(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_ClearGcpClearAvmuteBit(XV_HdmiTxSs *InstancePtr);
+
+int XV_HdmiTxSs_SetCallback(XV_HdmiTxSs *InstancePtr,
+		XV_HdmiTxSs_HandlerType HandlerType,
+		void *CallbackFuncPtr,
+		void *CallbackRef);
+int XV_HdmiTxSs_ReadEdid(XV_HdmiTxSs *InstancePtr, u8 *BufferPtr);
+int XV_HdmiTxSs_ReadEdidSegment(XV_HdmiTxSs *InstancePtr, u8 *Buffer, u8 segment);
+void XV_HdmiTxSs_SetScrambler(XV_HdmiTxSs *InstancePtr, u8 Enable);
+void XV_HdmiTxSs_StreamStart(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_SendAuxInfoframe(XV_HdmiTxSs *InstancePtr, void *AuxPtr);
+u32 XV_HdmiTxSs_SendGenericAuxInfoframe(XV_HdmiTxSs *InstancePtr, void *AuxPtr);
+void XV_HdmiTxSs_SetAudioChannels(XV_HdmiTxSs *InstancePtr, u8 AudioChannels);
+void XV_HdmiTxSs_AudioMute(XV_HdmiTxSs *InstancePtr, u8 Enable);
+void XV_HdmiTxSs_SetAudioFormat(XV_HdmiTxSs *InstancePtr,
+    XV_HdmiTx_AudioFormatType format);
+XV_HdmiTx_AudioFormatType XV_HdmiTxSs_GetAudioFormat(XV_HdmiTxSs *InstancePtr);
+XHdmiC_Aux *XV_HdmiTxSs_GetAuxiliary(XV_HdmiTxSs *InstancePtr);
+XHdmiC_AVI_InfoFrame *XV_HdmiTxSs_GetAviInfoframe(XV_HdmiTxSs *InstancePtr);
+XHdmiC_AudioInfoFrame *XV_HdmiTxSs_GetAudioInfoframe(XV_HdmiTxSs *InstancePtr);
+XHdmiC_VSIF *XV_HdmiTxSs_GetVSIF(XV_HdmiTxSs *InstancePtr);
+u32 XV_HdmiTxSs_SetStream(XV_HdmiTxSs *InstancePtr,
+    XVidC_VideoMode VideoMode,
+    XVidC_ColorFormat ColorFormat,
+    XVidC_ColorDepth Bpc,
+    XVidC_3DInfo *Info3D);
+XVidC_VideoStream *XV_HdmiTxSs_GetVideoStream(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_SetVideoStream(XV_HdmiTxSs *InstancePtr,
+                                    XVidC_VideoStream VidStream);
+void XV_HdmiTxSs_SetSamplingRate(XV_HdmiTxSs *InstancePtr, u8 SamplingRate);
+void XV_HdmiTxSs_SetVideoIDCode(XV_HdmiTxSs *InstancePtr, u8 Vic);
+void XV_HdmiTxSs_SetVideoStreamType(XV_HdmiTxSs *InstancePtr, u8 StreamType);
+void XV_HdmiTxSs_SetVideoStreamScramblingFlag(XV_HdmiTxSs *InstancePtr,
+                                                            u8 IsScrambled);
+void XV_HdmiTxSs_SetVideoStreamScramblingOverrideFlag(XV_HdmiTxSs *InstancePtr,
+														u8 OverrideScramble);
+void XV_HdmiTxSs_SetTmdsClockRatio(XV_HdmiTxSs *InstancePtr, u8 Ratio);
+u32 XV_HdmiTxSs_GetTmdsClockFreqHz(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_DetectHdmi20(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_RefClockChangeInit(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_ReportInfo(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_IsStreamUp(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_IsStreamConnected(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_IsStreamToggled(XV_HdmiTxSs *InstancePtr);
+u8 XV_HdmiTxSs_IsSinkHdcp14Capable(XV_HdmiTxSs *InstancePtr);
+u8 XV_HdmiTxSs_IsSinkHdcp22Capable(XV_HdmiTxSs *InstancePtr);
+
+void XV_HdmiTxSs_SetDefaultPpc(XV_HdmiTxSs *InstancePtr, u8 Id);
+void XV_HdmiTxSs_SetPpc(XV_HdmiTxSs *InstancePtr, u8 Id, u8 Ppc);
+struct v4l2_hdr10_payload
+	*XV_HdmiTxSs_GetDrmInfoframe(XV_HdmiTxSs *InstancePtr);
+
+#ifdef XV_HDMITXSS_LOG_ENABLE
+void XV_HdmiTxSs_LogReset(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_LogWrite(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_LogEvent Evt, u8 Data);
+u16 XV_HdmiTxSs_LogRead(XV_HdmiTxSs *InstancePtr);
+#endif
+int XV_HdmiTxSs_LogShow(XV_HdmiTxSs *InstancePtr, char *buff, int buff_size);
+int XV_HdmiTxSs_ShowInfo(XV_HdmiTxSs *InstancePtr, char *buff, int buff_size);
+
+#ifdef USE_HDCP_TX
+void XV_HdmiTxSs_HdcpSetKey(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_HdcpKeyType KeyType, u8 *KeyPtr);
+int XV_HdmiTxSs_HdcpPoll(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpSetProtocol(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_HdcpProtocol Protocol);
+int XV_HdmiTxSs_HdcpSetCapability(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_HdcpProtocol Protocol);
+XV_HdmiTxSs_HdcpProtocol XV_HdmiTxSs_HdcpGetProtocol(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpClearEvents(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpPushEvent(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_HdcpEvent Event);
+int XV_HdmiTxSs_HdcpEnable(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpDisable(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpAuthRequest(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpEnableEncryption(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpDisableEncryption(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpEnableBlank(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpDisableBlank(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpIsEnabled(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpIsAuthenticated(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpIsEncrypted(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpIsInProgress(XV_HdmiTxSs *InstancePtr);
+
+int XV_HdmiTxSs_HdcpInfo(XV_HdmiTxSs *InstancePtr, char *buff, int buff_size);
+void XV_HdmiTxSs_HdcpSetInfoDetail(XV_HdmiTxSs *InstancePtr, u8 Verbose);
+
+void *XV_HdmiTxSs_HdcpGetTopology(XV_HdmiTxSs *InstancePtr);
+u8 *XV_HdmiTxSs_HdcpGetTopologyReceiverIdList(XV_HdmiTxSs *InstancePtr);
+u32 XV_HdmiTxSs_HdcpGetTopologyField(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_HdcpTopologyField Field);
+
+void XV_HdmiTxSs_HdcpSetContentStreamType(XV_HdmiTxSs *InstancePtr,
+       XV_HdmiTxSs_HdcpContentStreamType StreamType);
+int XV_HdmiTxSs_HdcpIsRepeater(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpSetRepeater(XV_HdmiTxSs *InstancePtr, u8 Set);
+int XV_HdmiTxSs_HdcpIsInComputations(XV_HdmiTxSs *InstancePtr);
+int XV_HdmiTxSs_HdcpIsInWaitforready(XV_HdmiTxSs *InstancePtr);
+
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+int XV_HdmiTxSs_HdcpTimerStart(void *InstancePtr, u16 TimeoutInMs);
+int XV_HdmiTxSs_HdcpTimerStop(void *InstancePtr);
+int XV_HdmiTxSs_HdcpTimerBusyDelay(void *InstancePtr, u16 DelayInMs);
+
+void XV_HdmiTxSS_HdcpIntrHandler(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSS_HdcpTimerIntrHandler(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSs_HdcpTimerCallback(void *CallBackRef, u8 TimerChannel);
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+void XV_HdmiTxSS_Hdcp22TimerIntrHandler(XV_HdmiTxSs *InstancePtr);
+#endif
+
+void XV_HdmiTxSS_MaskEnable(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSS_MaskDisable(XV_HdmiTxSs *InstancePtr);
+void XV_HdmiTxSS_MaskNoise(XV_HdmiTxSs *InstancePtr, u8 Enable);
+void XV_HdmiTxSS_MaskSetRed(XV_HdmiTxSs *InstancePtr, u16 Value);
+void XV_HdmiTxSS_MaskSetGreen(XV_HdmiTxSs *InstancePtr, u16 Value);
+void XV_HdmiTxSS_MaskSetBlue(XV_HdmiTxSs *InstancePtr, u16 Value);
+void XV_HdmiTxSS_SetBackgroundColor(XV_HdmiTxSs *InstancePtr,
+                                    XVMaskColorId  ColorId);
+u8 XV_HdmiTxSS_IsMasked(XV_HdmiTxSs *InstancePtr);
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_coreinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_coreinit.c
@@ -0,0 +1,436 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitxss_coreinit.c
+* @{
+* @details
+
+* HDMI TX Subsystem Sub-Cores initialization
+* The functions in this file provides an abstraction from the initialization
+* sequence for included sub-cores. Subsystem is assigned an address and range
+* on the axi-lite interface. This address space is condensed where-in each
+* sub-core is at a fixed offset from the subsystem base address. For processor
+* to be able to access the sub-core this offset needs to be transalted into a
+* absolute address within the subsystems addressable range
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     20/01/16 Added remapper support
+* 1.2   MG     03/02/16 Added HDCP support
+* 1.3   MH     23/04/16 VTC driver has been updated to avoid processor
+*                       exceptions. Workarounds have been removed.
+* 1.4   MH     23/06/16 Added HDCP repeater support.
+* 1.5   YH     18/07/16 Replace xil_printf with xdbg_printf
+* 1.6   YH     25/07/16 Used UINTPTR instead of u32 for BaseAddr,HighAddr,Offset
+*                       AbsAddr
+* 1.7   MH     08/08/16 Updates to optimize out HDCP when excluded.
+* 1.8   YH     17/08/16 Added Event Log
+* 1.9   YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.10  MMO    03/01/17 Remove XV_HdmiTxSs_ComputeSubcoreAbsAddr API, as it
+*                            handles in the "_g" TCL generation
+*                       Re-align coding style to ensure, 80 characters per row
+* 3.2   MH     04/24/17 Set default HDMI mode in XV_HdmiTxSs_SubcoreInitHdmiTx
+* 3.3   MH     07/17/17 Set HDCP 2.2 polling value to 10 ms.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include "xv_hdmitxss_coreinit.h"
+
+/************************** Constant Definitions *****************************/
+
+/************************** Function Prototypes ******************************/
+#ifdef USE_HDCP_TX
+static int XV_HdmiTxSs_DdcReadHandler(u8 DeviceAddress,
+    u16 ByteCount, u8* BufferPtr, u8 Stop, void *RefPtr);
+static int XV_HdmiTxSs_DdcWriteHandler(u8 DeviceAddress,
+    u16 ByteCount, u8* BufferPtr, u8 Stop, void *RefPtr);
+#endif
+
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiTxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_SubcoreInitHdmiTx(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+  int Status;
+  XV_HdmiTx_Config *ConfigPtr;
+
+  if (HdmiTxSsPtr->HdmiTxPtr) {
+    /* Get core configuration */
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_HDMITX_INIT, 0);
+#endif
+    ConfigPtr  = XV_HdmiTx_LookupConfig(HdmiTxSsPtr->Config.HdmiTx.DeviceId);
+    if (ConfigPtr == NULL) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "HDMITXSS ERR:: HDMI TX device not found\r\n");
+      return(XST_FAILURE);
+    }
+
+    /* Initialize core */
+    Status = XV_HdmiTx_CfgInitialize(HdmiTxSsPtr->HdmiTxPtr,
+                                    ConfigPtr,
+                                    HdmiTxSsPtr->Config.HdmiTx.AbsAddr);
+
+    if (Status != XST_SUCCESS) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "HDMITXSS ERR:: HDMI TX Initialization failed\r\n");
+      return(XST_FAILURE);
+    }
+
+    /* Set default transmitter mode to HDMI */
+    XV_HdmiTxSS_SetHdmiMode(HdmiTxSsPtr);
+  }
+  return(XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiTxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_SubcoreInitVtc(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+  int Status;
+  XVtc_Config *ConfigPtr;
+
+  if (HdmiTxSsPtr->VtcPtr) {
+    /* Get core configuration */
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_VTC_INIT, 0);
+#endif
+    ConfigPtr  = XVtc_LookupConfig(HdmiTxSsPtr->Config.Vtc.DeviceId);
+    if (ConfigPtr == NULL) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,"HDMITXSS ERR:: VTC device not found\r\n");
+      return(XST_FAILURE);
+    }
+
+    /* Initialize core */
+    Status = XVtc_CfgInitialize(HdmiTxSsPtr->VtcPtr,
+                                ConfigPtr,
+                                HdmiTxSsPtr->Config.Vtc.AbsAddr);
+
+    if (Status != XST_SUCCESS) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "HDMITXSS ERR:: VTC Initialization failed\r\n");
+      return(XST_FAILURE);
+    }
+  }
+  return(XST_SUCCESS);
+}
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiTxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_SubcoreInitHdcpTimer(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+  int Status;
+  XTmrCtr_Config *ConfigPtr;
+
+  if (HdmiTxSsPtr->HdcpTimerPtr) {
+    /* Get core configuration */
+#ifdef XV_HDMITXSS_LOG_ENABLE
+    XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_HDCPTIMER_INIT, 0);
+#endif
+    ConfigPtr  = XTmrCtr_LookupConfig(HdmiTxSsPtr->Config.HdcpTimer.DeviceId);
+    if (ConfigPtr == NULL) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "HDMITXSS ERR:: AXIS Timer device not found\r\n");
+      return(XST_FAILURE);
+    }
+
+    /* Setup the instance */
+    memset(HdmiTxSsPtr->HdcpTimerPtr, 0, sizeof(XTmrCtr));
+
+    /* Initialize core */
+    XTmrCtr_CfgInitialize(HdmiTxSsPtr->HdcpTimerPtr,
+                          ConfigPtr,
+                          HdmiTxSsPtr->Config.HdcpTimer.AbsAddr);
+
+    Status = XTmrCtr_InitHw(HdmiTxSsPtr->HdcpTimerPtr);
+
+    /* Set Timer Counter instance in HDCP to the generic Hdcp1xRef
+     * that will be used in callbacks */
+    HdmiTxSsPtr->Hdcp14Ptr->Hdcp1xRef = (void *)HdmiTxSsPtr->HdcpTimerPtr;
+
+    /* Initialize the hdcp timer functions */
+    XHdcp1x_SetTimerStart(HdmiTxSsPtr->Hdcp14Ptr,
+      &XV_HdmiTxSs_HdcpTimerStart);
+    XHdcp1x_SetTimerStop(HdmiTxSsPtr->Hdcp14Ptr,
+      &XV_HdmiTxSs_HdcpTimerStop);
+    XHdcp1x_SetTimerDelay(HdmiTxSsPtr->Hdcp14Ptr,
+      &XV_HdmiTxSs_HdcpTimerBusyDelay);
+
+    if (Status != XST_SUCCESS) {
+      xdbg_printf(XDBG_DEBUG_GENERAL,
+                  "HDMITXSS ERR:: AXI Timer Initialization failed\r\n");
+      return(XST_FAILURE);
+    }
+  }
+  return(XST_SUCCESS);
+}
+
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiTxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_SubcoreInitHdcp14(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+  int Status;
+  XHdcp1x_Config *ConfigPtr;
+
+  /* Is the HDCP 1.4 TX present? */
+  if (HdmiTxSsPtr->Hdcp14Ptr) {
+
+    /* Is the key loaded? */
+    if (HdmiTxSsPtr->Hdcp14KeyPtr) {
+
+      /* Get core configuration */
+#ifdef XV_HDMITXSS_LOG_ENABLE
+      XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_HDCP14_INIT, 0);
+#endif
+      ConfigPtr  = XHdcp1x_LookupConfig(HdmiTxSsPtr->Config.Hdcp14.DeviceId);
+      if (ConfigPtr == NULL){
+        xdbg_printf(XDBG_DEBUG_GENERAL,
+                    "HDMITXSS ERR:: HDCP 1.4 device not found\r\n");
+        return(XST_FAILURE);
+      }
+
+      /* Initialize core */
+      void *PhyIfPtr = HdmiTxSsPtr->HdmiTxPtr;
+
+      Status = XHdcp1x_CfgInitialize(HdmiTxSsPtr->Hdcp14Ptr,
+                                        ConfigPtr,
+                                        PhyIfPtr,
+                                        HdmiTxSsPtr->Config.Hdcp14.AbsAddr);
+
+      /* Self-test the hdcp interface */
+      if (XHdcp1x_SelfTest(HdmiTxSsPtr->Hdcp14Ptr) != XST_SUCCESS) {
+          Status = XST_FAILURE;
+      }
+
+      /* Set-up the DDC Handlers */
+      XHdcp1x_SetCallback(HdmiTxSsPtr->Hdcp14Ptr,
+                          XHDCP1X_HANDLER_DDC_WRITE,
+                          (void *)XV_HdmiTxSs_DdcWriteHandler,
+						  (void *)HdmiTxSsPtr->HdmiTxPtr);
+
+      XHdcp1x_SetCallback(HdmiTxSsPtr->Hdcp14Ptr,
+                          XHDCP1X_HANDLER_DDC_READ,
+						  (void *)XV_HdmiTxSs_DdcReadHandler,
+						  (void *)HdmiTxSsPtr->HdmiTxPtr);
+
+      if (Status != XST_SUCCESS) {
+        xdbg_printf(XDBG_DEBUG_GENERAL,
+                    "HDMITXSS ERR:: HDCP 1.4 Initialization failed\r\n");
+        return(XST_FAILURE);
+      }
+
+      /* Key select */
+      XHdcp1x_SetKeySelect(HdmiTxSsPtr->Hdcp14Ptr, XV_HDMITXSS_HDCP_KEYSEL);
+
+      /* Load SRM */
+
+
+      /* Disable HDCP 1.4 repeater */
+      HdmiTxSsPtr->Hdcp14Ptr->IsRepeater = 0;
+    }
+  }
+  return(XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+* This function initializes the included sub-core to it's static configuration
+*
+* @param  HdmiTxSsPtr is a pointer to the Subsystem instance to be worked on.
+*
+* @return XST_SUCCESS/XST_FAILURE
+*
+******************************************************************************/
+int XV_HdmiTxSs_SubcoreInitHdcp22(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+  int Status;
+  XHdcp22_Tx_Config *Hdcp22TxConfig;
+
+  /* Is the HDCP 2.2 TX present? */
+  if (HdmiTxSsPtr->Hdcp22Ptr) {
+
+    /* Is the key loaded? */
+    if (HdmiTxSsPtr->Hdcp22Lc128Ptr && HdmiTxSsPtr->Hdcp22SrmPtr) {
+
+      /* Get core configuration */
+#ifdef XV_HDMITXSS_LOG_ENABLE
+      XV_HdmiTxSs_LogWrite(HdmiTxSsPtr, XV_HDMITXSS_LOG_EVT_HDCP22_INIT, 0);
+#endif
+      /* Initialize HDCP 2.2 TX */
+      Hdcp22TxConfig =
+                    XHdcp22Tx_LookupConfig(HdmiTxSsPtr->Config.Hdcp22.DeviceId);
+
+      if (Hdcp22TxConfig == NULL) {
+        xdbg_printf(XDBG_DEBUG_GENERAL,
+                    "HDMITXSS ERR:: HDCP 2.2 device not found\r\n");
+        return XST_FAILURE;
+      }
+
+      Status = XHdcp22Tx_CfgInitialize(HdmiTxSsPtr->Hdcp22Ptr,
+                                       Hdcp22TxConfig,
+                                       HdmiTxSsPtr->Config.Hdcp22.AbsAddr);
+      if (Status != XST_SUCCESS) {
+        xdbg_printf(XDBG_DEBUG_GENERAL,
+                    "HDMITXSS ERR:: HDCP 2.2 Initialization failed\r\n");
+        return Status;
+      }
+
+      /* Set-up the DDC Handlers */
+      XHdcp22Tx_SetCallback(HdmiTxSsPtr->Hdcp22Ptr,
+                            XHDCP22_TX_HANDLER_DDC_WRITE,
+							(void *)XV_HdmiTxSs_DdcWriteHandler,
+							(void *)HdmiTxSsPtr->HdmiTxPtr);
+
+      XHdcp22Tx_SetCallback(HdmiTxSsPtr->Hdcp22Ptr,
+                            XHDCP22_TX_HANDLER_DDC_READ,
+							(void *)XV_HdmiTxSs_DdcReadHandler,
+							(void *)HdmiTxSsPtr->HdmiTxPtr);
+
+      /* Set polling value */
+      XHdcp22Tx_SetMessagePollingValue(HdmiTxSsPtr->Hdcp22Ptr, 10);
+
+      XHdcp22Tx_LogReset(HdmiTxSsPtr->Hdcp22Ptr, FALSE);
+
+      /* Load key */
+      XHdcp22Tx_LoadLc128(HdmiTxSsPtr->Hdcp22Ptr, HdmiTxSsPtr->Hdcp22Lc128Ptr);
+
+      /* Load SRM */
+      Status = XHdcp22Tx_LoadRevocationTable(HdmiTxSsPtr->Hdcp22Ptr,
+                                             HdmiTxSsPtr->Hdcp22SrmPtr);
+      if (Status != XST_SUCCESS) {
+        xdbg_printf(XDBG_DEBUG_GENERAL,
+                    "HDMITXSS ERR:: HDCP 2.2 failed to load SRM\r\n");
+        return Status;
+      }
+
+      /* Clear the event queue */
+      XV_HdmiTxSs_HdcpClearEvents(HdmiTxSsPtr);
+    }
+  }
+
+  return (XST_SUCCESS);
+}
+#endif
+
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC read handler for the TX.
+ *
+ * @param DeviceAddress is the 7-bit I2C slave address
+ *
+ * @param ByteCount is the number of bytes to read
+ *
+ * @param BufferPtr is a pointer to the buffer where
+ *        the read data is written to.
+ *
+ * @param Stop indicates if a I2C stop condition is generated
+ *        at the end of the burst.
+ *
+ * @param RefPtr is a callback reference to the HDMI TX instance
+ *
+ * @return
+ *  - XST_SUCCESS if action was successful
+ *  - XST_FAILURE if action was not successful
+ *
+ ******************************************************************************/
+static int XV_HdmiTxSs_DdcReadHandler(u8 DeviceAddress,
+    u16 ByteCount, u8* BufferPtr, u8 Stop, void *RefPtr)
+{
+  XV_HdmiTx *InstancePtr = (XV_HdmiTx *)RefPtr;
+  return XV_HdmiTx_DdcRead(InstancePtr,
+                           DeviceAddress,
+                           ByteCount,
+                           BufferPtr,
+                           Stop);
+}
+
+/*****************************************************************************/
+/**
+ *
+ * This is the DDC write handler for the TX.
+ *
+ * @param DeviceAddress is the 7-bit I2C slave address
+ *
+ * @param ByteCount is the number of bytes to write
+ *
+ * @param BufferPtr is a pointer to the buffer containing
+ *        the data to be written.
+ *
+ * @param Stop indicates if a I2C stop condition is generated
+ *        at the end of the burst.
+ *
+ * @param RefPtr is a callback reference to the HDMI TX instance
+ *
+ * @return
+ *  - XST_SUCCESS if action was successful
+ *  - XST_FAILURE if action was not successful
+ *
+ ******************************************************************************/
+static int XV_HdmiTxSs_DdcWriteHandler(u8 DeviceAddress,
+    u16 ByteCount, u8* BufferPtr, u8 Stop, void *RefPtr)
+{
+  XV_HdmiTx *InstancePtr = (XV_HdmiTx *)RefPtr;
+  return XV_HdmiTx_DdcWrite(InstancePtr,
+                            DeviceAddress,
+                            ByteCount,
+                            BufferPtr,
+                            Stop);
+}
+#endif
+
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_coreinit.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_coreinit.h
@@ -0,0 +1,67 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitxss_coreinit.h
+* @{
+* @details
+*
+* This header file contains the hdmi tx subsystem sub-cores
+* initialization routines and helper functions.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00         10/07/15 Initial release.
+* 1.1   yh     20/01/16 Added remapper support
+* 1.2   MG     03/02/16 Added HDCP support
+* 1.3   MH     08/08/16 Updates to optimize out HDCP when excluded.
+* 1.4   YH     14/11/16 Remove Remapper APIs as remapper feature is moved to
+*                       video bridge and controlled by HDMI core
+* 1.5   MMO    03/01/16 Remove repetitive inclusion of header files
+* </pre>
+*
+******************************************************************************/
+#ifndef XV_HDMITXSS_COREINIT_H__  /* prevent circular inclusions */
+#define XV_HDMITXSS_COREINIT_H__  /* by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "xv_hdmitxss.h"
+/************************** Constant Definitions *****************************/
+
+/************************** Function Prototypes ******************************/
+int XV_HdmiTxSs_SubcoreInitHdmiTx(XV_HdmiTxSs *HdmiTxSsPtr);
+int XV_HdmiTxSs_SubcoreInitVtc(XV_HdmiTxSs *HdmiTxSsPtr);
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+int XV_HdmiTxSs_SubcoreInitHdcpTimer(XV_HdmiTxSs *HdmiTxSsPtr);
+int XV_HdmiTxSs_SubcoreInitHdcp14(XV_HdmiTxSs *HdmiTxSsPtr);
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+int XV_HdmiTxSs_SubcoreInitHdcp22(XV_HdmiTxSs *HdmiTxSsPtr);
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_hdcp.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_hdcp.c
@@ -0,0 +1,2239 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xv_hdmitxss_hdcp.c
+*
+* This is main code of Xilinx HDMI Transmitter Subsystem device driver.
+* Please see xv_hdmitxss.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ---- -------- -------------------------------------------------------
+* 1.00   MMO 19/12/16 Move HDCP Code from xv_hdmitxss.c to xv_hdmitxss_hdcp.c
+* 3.20   MH  04/12/17 Updated function XV_HdmiTxSs_IsSinkHdcp14Capable and
+*                     XV_HdmiTxSs_IsSinkHdcp22Capable.
+*            08/09/17 Added function XV_HdmiTxSs_HdcpSetCapability
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+#include <linux/version.h>
+#include "xv_hdmitxss.h"
+/************************** Constant Definitions *****************************/
+
+/**************************** Type Definitions *******************************/
+
+/**************************** Local Global ***********************************/
+
+/************************** Function Prototypes ******************************/
+// HDCP specific
+#ifdef USE_HDCP_TX
+static XV_HdmiTxSs_HdcpEvent XV_HdmiTxSs_HdcpGetEvent(XV_HdmiTxSs *InstancePtr);
+static int XV_HdmiTxSs_HdcpProcessEvents(XV_HdmiTxSs *InstancePtr);
+static int XV_HdmiTxSs_HdcpReset(XV_HdmiTxSs *InstancePtr);
+static u32 XV_HdmiTxSs_HdcpGetTopologyDepth(XV_HdmiTxSs *InstancePtr);
+static u32 XV_HdmiTxSs_HdcpGetTopologyDeviceCnt(XV_HdmiTxSs *InstancePtr);
+static u8 XV_HdmiTxSs_HdcpGetTopologyMaxDevsExceeded(XV_HdmiTxSs *InstancePtr);
+static u8
+        XV_HdmiTxSs_HdcpGetTopologyMaxCascadeExceeded(XV_HdmiTxSs *InstancePtr);
+static u8
+  XV_HdmiTxSs_HdcpGetTopologyHdcp2LegacyDeviceDownstream(XV_HdmiTxSs *InstancePtr);
+static u8
+     XV_HdmiTxSs_HdcpGetTopologyHdcp1DeviceDownstream(XV_HdmiTxSs *InstancePtr);
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+static u32 XV_HdmiTxSs_HdcpTimerConvUsToTicks(u32 TimeoutInUs,
+    u32 ClockFrequency);
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+/************************** Function Definition ******************************/
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDCP
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiTxSS_HdcpIntrHandler(XV_HdmiTxSs *InstancePtr)
+{
+    XHdcp1x_CipherIntrHandler(InstancePtr->Hdcp14Ptr);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDCP Timer
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiTxSS_HdcpTimerIntrHandler(XV_HdmiTxSs *InstancePtr)
+{
+    XTmrCtr_InterruptHandler(InstancePtr->HdcpTimerPtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+/*****************************************************************************/
+/**
+ * This function calls the interrupt handler for HDCP 2.2 Timer
+ *
+ * @param  InstancePtr is a pointer to the HDMI TX Subsystem
+ *
+ *****************************************************************************/
+void XV_HdmiTxSS_Hdcp22TimerIntrHandler(XV_HdmiTxSs *InstancePtr)
+{
+  XTmrCtr *XTmrCtrPtr;
+
+  XTmrCtrPtr = XHdcp22Tx_GetTimer(InstancePtr->Hdcp22Ptr);
+
+  XTmrCtr_InterruptHandler(XTmrCtrPtr);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function converts from microseconds to timer ticks
+*
+* @param TimeoutInUs  the timeout to convert
+* @param ClockFrequency  the clock frequency to use in the conversion
+*
+* @return
+*   The number of "ticks"
+*
+* @note
+*   None.
+*
+******************************************************************************/
+static u32 XV_HdmiTxSs_HdcpTimerConvUsToTicks(u32 TimeoutInUs,
+                                                    u32 ClockFrequency)
+{
+    u32 TimeoutFreq = 0;
+    u32 NumTicks = 0;
+
+    /* Check for greater than one second */
+    if (TimeoutInUs > 1000000ul) {
+        u32 NumSeconds = 0;
+
+        /* Determine theNumSeconds */
+        NumSeconds = (TimeoutInUs/1000000ul);
+
+        /* Update theNumTicks */
+        NumTicks = (NumSeconds*ClockFrequency);
+
+        /* Adjust theTimeoutInUs */
+        TimeoutInUs -= (NumSeconds*1000000ul);
+    }
+
+    /* Convert TimeoutFreq to a frequency */
+    TimeoutFreq  = 1000;
+    TimeoutFreq *= 1000;
+    TimeoutFreq /= TimeoutInUs;
+
+    /* Update NumTicks */
+    NumTicks += ((ClockFrequency / TimeoutFreq) + 1);
+
+    return (NumTicks);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/*****************************************************************************/
+/**
+*
+* This function serves as the timer callback function
+*
+* @param CallBackRef  the callback reference value
+* @param TimerChannel  the channel within the timer that expired
+*
+* @return
+*   void
+*
+* @note
+*   None
+*
+******************************************************************************/
+void XV_HdmiTxSs_HdcpTimerCallback(void* CallBackRef, u8 TimerChannel)
+{
+    XHdcp1x* HdcpPtr = (XHdcp1x*) CallBackRef;
+
+    TimerChannel = TimerChannel;
+    XHdcp1x_HandleTimeout(HdcpPtr);
+    return;
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function starts a timer on behalf of an hdcp interface
+*
+* @param InstancePtr  the hdcp interface
+* @param TimeoutInMs  the timer duration in milliseconds
+*
+* @return
+*   XST_SUCCESS if successful
+*
+* @note
+*   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpTimerStart(void *InstancePtr, u16 TimeoutInMs)
+{
+    XHdcp1x *HdcpPtr = (XHdcp1x *)InstancePtr;
+    XTmrCtr *TimerPtr = (XTmrCtr *)HdcpPtr->Hdcp1xRef;
+
+    u8 TimerChannel = 0;
+    u32 TimerOptions = 0;
+    u32 NumTicks = 0;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(TimerPtr != NULL);
+
+
+    /* Determine NumTicks */
+    NumTicks = XV_HdmiTxSs_HdcpTimerConvUsToTicks((TimeoutInMs*1000ul),
+                  TimerPtr->Config.SysClockFreqHz);
+
+
+    /* Stop it */
+    XTmrCtr_Stop(TimerPtr, TimerChannel);
+
+    /* Configure the callback */
+    XTmrCtr_SetHandler(TimerPtr, &XV_HdmiTxSs_HdcpTimerCallback,
+                                                (void*) HdcpPtr);
+
+    /* Configure the timer options */
+    TimerOptions  = XTmrCtr_GetOptions(TimerPtr, TimerChannel);
+    TimerOptions |=  XTC_DOWN_COUNT_OPTION;
+    TimerOptions |=  XTC_INT_MODE_OPTION;
+    TimerOptions &= ~XTC_AUTO_RELOAD_OPTION;
+    XTmrCtr_SetOptions(TimerPtr, TimerChannel, TimerOptions);
+
+    /* Set the timeout and start */
+    XTmrCtr_SetResetValue(TimerPtr, TimerChannel, NumTicks);
+    XTmrCtr_Start(TimerPtr, TimerChannel);
+
+    return (XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function stops a timer on behalf of an hdcp interface
+*
+* @param InstancePtr  the hdcp interface
+*
+* @return
+*   XST_SUCCESS if successful
+*
+* @note
+*   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpTimerStop(void *InstancePtr)
+{
+    XHdcp1x *HdcpPtr = (XHdcp1x *)InstancePtr;
+    XTmrCtr *TimerPtr = (XTmrCtr *)HdcpPtr->Hdcp1xRef;
+
+    u8 TimerChannel = 0;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(TimerPtr != NULL);
+
+    /* Stop it */
+    XTmrCtr_Stop(TimerPtr, TimerChannel);
+
+    return (XST_SUCCESS);
+}
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+/******************************************************************************/
+/**
+*
+* This function busy waits for an interval on behalf of an hdcp interface
+*
+* @param InstancePtr  the hdcp interface
+* @param DelayInMs  the delay duration in milliseconds
+*
+* @return
+*   XST_SUCCESS if successful
+*
+* @note
+*   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpTimerBusyDelay(void *InstancePtr, u16 DelayInMs)
+{
+    XHdcp1x *HdcpPtr = (XHdcp1x *)InstancePtr;
+    XTmrCtr *TimerPtr = (XTmrCtr *)HdcpPtr->Hdcp1xRef;
+
+    u8 TimerChannel = 0;
+    u32 TimerOptions = 0;
+    u32 NumTicks = 0;
+
+    /* Verify argument. */
+    Xil_AssertNonvoid(TimerPtr != NULL);
+
+
+    /* Determine NumTicks */
+    NumTicks = XV_HdmiTxSs_HdcpTimerConvUsToTicks((DelayInMs*1000ul),
+                  TimerPtr->Config.SysClockFreqHz);
+
+    /* Stop it */
+    XTmrCtr_Stop(TimerPtr, TimerChannel);
+
+    /* Configure the timer options */
+    TimerOptions  = XTmrCtr_GetOptions(TimerPtr, TimerChannel);
+    TimerOptions |=  XTC_DOWN_COUNT_OPTION;
+    TimerOptions &= ~XTC_INT_MODE_OPTION;
+    TimerOptions &= ~XTC_AUTO_RELOAD_OPTION;
+    XTmrCtr_SetOptions(TimerPtr, TimerChannel, TimerOptions);
+
+    /* Set the timeout and start */
+    XTmrCtr_SetResetValue(TimerPtr, TimerChannel, NumTicks);
+    XTmrCtr_Start(TimerPtr, TimerChannel);
+
+    /* Wait until done */
+    while (!XTmrCtr_IsExpired(TimerPtr, TimerChannel));
+
+    return (XST_SUCCESS);
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function pushes an event into the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+* @param Event is the event to be pushed in the queue.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpPushEvent(XV_HdmiTxSs *InstancePtr,
+                              XV_HdmiTxSs_HdcpEvent Event)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(Event < XV_HDMITXSS_HDCP_INVALID_EVT);
+
+  /* Write event into the queue */
+  InstancePtr->HdcpEventQueue.Queue[InstancePtr->HdcpEventQueue.Head] = Event;
+
+  /* Update head pointer */
+  if (InstancePtr->HdcpEventQueue.Head ==
+                                        (XV_HDMITXSS_HDCP_MAX_QUEUE_SIZE - 1)) {
+    InstancePtr->HdcpEventQueue.Head = 0;
+  }
+  else {
+    InstancePtr->HdcpEventQueue.Head++;
+  }
+
+  /* Check tail pointer. When the two pointer are equal, then the buffer
+   * is full. In this case then increment the tail pointer as well to
+   * remove the oldest entry from the buffer.
+   */
+  if (InstancePtr->HdcpEventQueue.Tail == InstancePtr->HdcpEventQueue.Head) {
+    if (InstancePtr->HdcpEventQueue.Tail ==
+                                        (XV_HDMITXSS_HDCP_MAX_QUEUE_SIZE - 1)) {
+      InstancePtr->HdcpEventQueue.Tail = 0;
+    }
+    else {
+      InstancePtr->HdcpEventQueue.Tail++;
+    }
+  }
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets an event from the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return When the queue is filled, the next event is returned.
+*         When the queue is empty, XV_HDMITXSS_HDCP_NO_EVT is returned.
+*
+* @note   None.
+*
+******************************************************************************/
+static XV_HdmiTxSs_HdcpEvent XV_HdmiTxSs_HdcpGetEvent(XV_HdmiTxSs *InstancePtr)
+{
+  XV_HdmiTxSs_HdcpEvent Event;
+
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  /* Check if there are any events in the queue */
+  if (InstancePtr->HdcpEventQueue.Tail == InstancePtr->HdcpEventQueue.Head) {
+    return XV_HDMITXSS_HDCP_NO_EVT;
+  }
+
+  Event = InstancePtr->HdcpEventQueue.Queue[InstancePtr->HdcpEventQueue.Tail];
+
+  /* Update tail pointer */
+  if (InstancePtr->HdcpEventQueue.Tail ==
+                                        (XV_HDMITXSS_HDCP_MAX_QUEUE_SIZE - 1)) {
+    InstancePtr->HdcpEventQueue.Tail = 0;
+  }
+  else {
+    InstancePtr->HdcpEventQueue.Tail++;
+  }
+
+  return Event;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function clears all pending events from the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpClearEvents(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  InstancePtr->HdcpEventQueue.Head = 0;
+  InstancePtr->HdcpEventQueue.Tail = 0;
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function processes pending events from the HDCP event queue.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiTxSs_HdcpProcessEvents(XV_HdmiTxSs *InstancePtr)
+{
+  XV_HdmiTxSs_HdcpEvent Event;
+  int Status = XST_SUCCESS;
+
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  Event = XV_HdmiTxSs_HdcpGetEvent(InstancePtr);
+  switch (Event) {
+
+    // Stream up
+    // Attempt authentication with downstream device
+    case XV_HDMITXSS_HDCP_STREAMUP_EVT :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        // Set physical state
+        XHdcp1x_SetPhysicalState(InstancePtr->Hdcp14Ptr, TRUE);
+        // This is needed to ensure that the previous command is executed.
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+#endif
+      break;
+
+    // Stream down
+    case XV_HDMITXSS_HDCP_STREAMDOWN_EVT :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        // Set physical state
+        XHdcp1x_SetPhysicalState(InstancePtr->Hdcp14Ptr, FALSE);
+        // This is needed to ensure that the previous command is executed.
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+#endif
+      XV_HdmiTxSs_HdcpReset(InstancePtr);
+      break;
+
+    // Connect
+    case XV_HDMITXSS_HDCP_CONNECT_EVT :
+      break;
+
+    // Disconnect
+    // Reset both HDCP protocols
+    case XV_HDMITXSS_HDCP_DISCONNECT_EVT :
+      XV_HdmiTxSs_HdcpReset(InstancePtr);
+      break;
+
+    // Authenticate
+    case XV_HDMITXSS_HDCP_AUTHENTICATE_EVT :
+      XV_HdmiTxSs_HdcpAuthRequest(InstancePtr);
+      break;
+
+    default :
+      break;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function schedules the available HDCP cores. Only the active
+* HDCP protocol poll function is executed. HDCP 1.4 and 2.2 poll
+* functions should not execute in parallel.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpPoll(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  /* Only poll when the HDCP is ready */
+  if (InstancePtr->HdcpIsReady) {
+
+    /* Process any pending events from the TX event queue */
+    XV_HdmiTxSs_HdcpProcessEvents(InstancePtr);
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    if (InstancePtr->Hdcp22Ptr) {
+      if (XHdcp22Tx_IsEnabled(InstancePtr->Hdcp22Ptr)) {
+       XHdcp22Tx_Poll(InstancePtr->Hdcp22Ptr);
+      }
+    }
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    if (InstancePtr->Hdcp14Ptr) {
+      if (XHdcp1x_IsEnabled(InstancePtr->Hdcp14Ptr)) {
+       XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+    }
+#endif
+  }
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function sets the active HDCP protocol and enables it.
+* The protocol can be set to either HDCP 1.4, 2.2, or None.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+* @param Protocol is the requested content protection scheme of type
+*        XV_HdmiTxSs_HdcpProtocol.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpSetProtocol(XV_HdmiTxSs *InstancePtr,
+                                XV_HdmiTxSs_HdcpProtocol Protocol)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid((Protocol == XV_HDMITXSS_HDCP_NONE)   ||
+                    (Protocol == XV_HDMITXSS_HDCP_14) ||
+                    (Protocol == XV_HDMITXSS_HDCP_22));
+
+  int Status;
+
+  // Set protocol
+  InstancePtr->HdcpProtocol = Protocol;
+
+  // Reset both protocols
+  Status = XV_HdmiTxSs_HdcpReset(InstancePtr);
+  if (Status != XST_SUCCESS) {
+    InstancePtr->HdcpProtocol = XV_HDMITXSS_HDCP_NONE;
+    return XST_FAILURE;
+  }
+
+  // Enable the requested protocol
+  Status = XV_HdmiTxSs_HdcpEnable(InstancePtr);
+  if (Status != XST_SUCCESS) {
+    InstancePtr->HdcpProtocol = XV_HDMITXSS_HDCP_NONE;
+    return XST_FAILURE;
+  }
+
+  return XST_SUCCESS;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP protocol capability used during authentication.
+* The protocol capability can be set to either HDCP 1.4, 2.2, Both, or None.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+* @param Protocol is the desired content protection scheme of type
+*        XV_HdmiTxSs_HdcpProtocol.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpSetCapability(XV_HdmiTxSs *InstancePtr,
+                                XV_HdmiTxSs_HdcpProtocol Protocol)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(Protocol <= XV_HDMITXSS_HDCP_BOTH);
+
+  // Set protocol
+  InstancePtr->HdcpCapability = Protocol;
+
+  return XST_SUCCESS;
+}
+#endif
+
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the active HDCP content protection scheme.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  @RequestedScheme is the requested content protection scheme.
+*
+* @note   None.
+*
+******************************************************************************/
+XV_HdmiTxSs_HdcpProtocol XV_HdmiTxSs_HdcpGetProtocol(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  return InstancePtr->HdcpProtocol;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function enables the requested HDCP protocol. This function
+* ensures that the HDCP protocols are mutually exclusive such that
+* either HDCP 1.4 or HDCP 2.2 is enabled and active at any given time.
+* When the protocol is set to None, both HDCP protocols are disabled.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpEnable(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status1 = XST_SUCCESS;
+  int Status2 = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol) {
+
+    /* Disable HDCP 1.4 and HDCP 2.2 */
+    case XV_HDMITXSS_HDCP_NONE :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        Status1 = XHdcp1x_Disable(InstancePtr->Hdcp14Ptr);
+        // This is needed to ensure that the previous command is executed.
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        Status2 = XHdcp22Tx_Disable(InstancePtr->Hdcp22Ptr);
+      }
+#endif
+      break;
+
+    /* Enable HDCP 1.4 and disable HDCP 2.2 */
+    case XV_HDMITXSS_HDCP_14 :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        Status1 = XHdcp1x_Enable(InstancePtr->Hdcp14Ptr);
+        // This is needed to ensure that the previous command is executed.
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+      else {
+        Status1 = XST_FAILURE;
+      }
+#else
+      Status1 = XST_FAILURE;
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        Status2 = XHdcp22Tx_Disable(InstancePtr->Hdcp22Ptr);
+      }
+#endif
+      break;
+
+    /* Enable HDCP 2.2 and disable HDCP 1.4 */
+    case XV_HDMITXSS_HDCP_22 :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        Status1 = XHdcp1x_Disable(InstancePtr->Hdcp14Ptr);
+        // This is needed to ensure that the previous command is executed.
+        XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+      }
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        Status2 = XHdcp22Tx_Enable(InstancePtr->Hdcp22Ptr);
+      }
+      else {
+        Status2 = XST_FAILURE;
+      }
+#else
+      Status2 = XST_FAILURE;
+#endif
+      break;
+
+    default :
+      return XST_FAILURE;
+  }
+
+  return (Status1 == XST_SUCCESS &&
+          Status2 == XST_SUCCESS) ?
+          XST_SUCCESS : XST_FAILURE;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function disables both HDCP 1.4 and 2.2 protocols.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpDisable(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  /* Set protocol to NONE then reset/disable HDCP 1.4 and 2.2 */
+  InstancePtr->HdcpProtocol = XV_HDMITXSS_HDCP_NONE;
+  Status = XV_HdmiTxSs_HdcpReset(InstancePtr);
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function resets both HDCP 1.4 and 2.2 protocols. This function
+* also disables the both HDCP 1.4 and 2.2 protocols.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+static int XV_HdmiTxSs_HdcpReset(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  // Resetting HDCP 1.4 causes the state machine to be enabled, therefore
+  // disable must be called immediately after reset is called.
+  if (InstancePtr->Hdcp14Ptr) {
+    Status = XHdcp1x_Reset(InstancePtr->Hdcp14Ptr);
+    // This is needed to ensure that the previous command is executed.
+    XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+
+    Status = XHdcp1x_Disable(InstancePtr->Hdcp14Ptr);
+    // This is needed to ensure that the previous command is executed.
+    XHdcp1x_Poll(InstancePtr->Hdcp14Ptr);
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  // HDCP 2.2
+  if (InstancePtr->Hdcp22Ptr) {
+    Status = XHdcp22Tx_Reset(InstancePtr->Hdcp22Ptr);
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+
+    Status = XHdcp22Tx_Disable(InstancePtr->Hdcp22Ptr);
+    if (Status != XST_SUCCESS)
+      return XST_FAILURE;
+  }
+#endif
+
+  // Set defaults
+  XV_HdmiTxSs_HdcpDisableEncryption(InstancePtr);
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function sends an authentication request to the connected receiver.
+* The HDCP protocol is determined automatically by checking the capabilities
+* of the connected device. When the connected device supports both HDCP 1.4
+* and HDCP 2.2, then HDCP 2.2 is given priority.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if authentication started successfully
+*  - XST_FAILURE if authentication did not start successfully
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpAuthRequest(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_FAILURE;
+
+  /* Always disable encryption */
+  if (XV_HdmiTxSs_HdcpDisableEncryption(InstancePtr) != XST_SUCCESS) {
+    XV_HdmiTxSs_HdcpSetProtocol(InstancePtr, XV_HDMITXSS_HDCP_NONE);
+    return XST_FAILURE;
+  }
+
+  /* Verify if sink is attached */
+  if (!XV_HdmiTx_IsStreamConnected(InstancePtr->HdmiTxPtr)) {
+    xdbg_printf(XDBG_DEBUG_GENERAL, "No sink is attached\r\n");
+    XV_HdmiTxSs_HdcpSetProtocol(InstancePtr, XV_HDMITXSS_HDCP_NONE);
+    return XST_FAILURE;
+  }
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  /* Authenticate HDCP 2.2, takes priority */
+  if ((InstancePtr->Hdcp22Ptr) &&
+      (InstancePtr->HdcpCapability == XV_HDMITXSS_HDCP_22 ||
+       InstancePtr->HdcpCapability == XV_HDMITXSS_HDCP_BOTH)) {
+    if (XV_HdmiTxSs_IsSinkHdcp22Capable(InstancePtr)) {
+      xdbg_printf(XDBG_DEBUG_GENERAL, "Starting HDCP 2.2 authentication\r\n");
+#ifdef XV_HDMITXSS_LOG_ENABLE
+      XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_HDCP22_AUTHREQ, 0);
+#endif
+	  Status = XV_HdmiTxSs_HdcpSetProtocol(InstancePtr, XV_HDMITXSS_HDCP_22);
+      Status |= XHdcp22Tx_Authenticate(InstancePtr->Hdcp22Ptr);
+    }
+    else {
+      Status = XST_FAILURE;
+      xdbg_printf(XDBG_DEBUG_GENERAL, "Sink is not HDCP 2.2 capable\r\n");
+    }
+  }
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  /* Authenticate HDCP 1.4 */
+  if ((InstancePtr->Hdcp14Ptr) && (Status == XST_FAILURE) &&
+      (InstancePtr->HdcpCapability == XV_HDMITXSS_HDCP_14 ||
+       InstancePtr->HdcpCapability == XV_HDMITXSS_HDCP_BOTH)) {
+    if (XV_HdmiTxSs_IsSinkHdcp14Capable(InstancePtr)) {
+      xdbg_printf(XDBG_DEBUG_GENERAL, "Starting HDCP 1.4 authentication\r\n");
+#ifdef XV_HDMITXSS_LOG_ENABLE
+      XV_HdmiTxSs_LogWrite(InstancePtr, XV_HDMITXSS_LOG_EVT_HDCP14_AUTHREQ, 0);
+#endif
+      Status = XV_HdmiTxSs_HdcpSetProtocol(InstancePtr, XV_HDMITXSS_HDCP_14);
+      Status |= XHdcp1x_Authenticate(InstancePtr->Hdcp14Ptr);
+    }
+    else {
+      Status = XST_FAILURE;
+      xdbg_printf(XDBG_DEBUG_GENERAL, "Sink is not HDCP 1.4 capable\r\n");
+    }
+  }
+#endif
+
+  /* Set protocol to None */
+  if (Status == XST_FAILURE) {
+    XV_HdmiTxSs_HdcpSetProtocol(InstancePtr, XV_HDMITXSS_HDCP_NONE);
+  }
+
+  return (Status == XST_SUCCESS) ? XST_SUCCESS : XST_FAILURE;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function enables encryption for the active HDCP protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpEnableEncryption(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      if (InstancePtr->Hdcp14Ptr) {
+        Status = XHdcp1x_EnableEncryption(InstancePtr->Hdcp14Ptr, 0x1);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_22 :
+      if (InstancePtr->Hdcp22Ptr) {
+        Status = XHdcp22Tx_EnableEncryption(InstancePtr->Hdcp22Ptr);
+      }
+      break;
+#endif
+
+    default :
+      Status = XST_FAILURE;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function disables encryption for both HDCP protocols.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpDisableEncryption(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = XST_SUCCESS;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if (InstancePtr->Hdcp14Ptr) {
+    Status = XHdcp1x_DisableEncryption(InstancePtr->Hdcp14Ptr, 0x1);
+
+    if (Status != XST_SUCCESS) {
+      return XST_FAILURE;
+    }
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  if (InstancePtr->Hdcp22Ptr) {
+    Status = XHdcp22Tx_DisableEncryption(InstancePtr->Hdcp22Ptr);
+
+    if (Status != XST_SUCCESS) {
+      return XST_FAILURE;
+    }
+  }
+#endif
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function enables cipher blank for the active HDCP protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpEnableBlank(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_Enable(InstancePtr->Hdcp14Ptr);
+        XHdcp1x_EnableBlank(InstancePtr->Hdcp14Ptr);
+        return XST_SUCCESS;
+      }
+#endif
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Tx_Enable(InstancePtr->Hdcp22Ptr);
+        XHdcp22Tx_EnableBlank(InstancePtr->Hdcp22Ptr);
+        return XST_SUCCESS;
+      }
+#endif
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      if (InstancePtr->Hdcp14Ptr) {
+        XHdcp1x_EnableBlank(InstancePtr->Hdcp14Ptr);
+        return XST_SUCCESS;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_22 :
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Tx_EnableBlank(InstancePtr->Hdcp22Ptr);
+        return XST_SUCCESS;
+      }
+      break;
+#endif
+
+    default :
+      /* Do nothing */
+      break;
+  }
+
+  return XST_FAILURE;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function disables cipher blank for both HDCP protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpDisableBlank(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if (InstancePtr->Hdcp14Ptr) {
+    XHdcp1x_DisableBlank(InstancePtr->Hdcp14Ptr);
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  if (InstancePtr->Hdcp22Ptr) {
+    XHdcp22Tx_DisableBlank(InstancePtr->Hdcp22Ptr);
+  }
+#endif
+
+  return XST_SUCCESS;
+}
+#endif
+
+/*****************************************************************************/
+/**
+*
+* This function determines if the connected HDMI sink is HDCP 1.4 capable
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if sink is HDCP 1.4 capable and ready to authenticate.
+*  - FALSE if sink does not support HDCP 1.4 or is not ready.
+*
+******************************************************************************/
+u8 XV_HdmiTxSs_IsSinkHdcp14Capable(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  if (InstancePtr->Hdcp14Ptr) {
+    if (XHdcp1x_IsDwnstrmCapable(InstancePtr->Hdcp14Ptr)) {
+      return TRUE;
+    }
+    else {
+      return FALSE;
+    }
+  }
+  else {
+    return FALSE;
+  }
+#endif
+
+  return FALSE;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function determines if the connected HDMI sink is HDCP 2.2 capable.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if sink is HDCP 2.2 capable and ready to authenticate.
+*  - FALSE if sink does not support HDCP 2.2 or is not ready.
+*
+******************************************************************************/
+u8 XV_HdmiTxSs_IsSinkHdcp22Capable(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  if (InstancePtr->Hdcp22Ptr) {
+    if (XHdcp22Tx_IsDwnstrmCapable(InstancePtr->Hdcp22Ptr)) {
+      return TRUE;
+    }
+    else {
+      return FALSE;
+    }
+  }
+  else {
+    return FALSE;
+  }
+#endif
+
+  return FALSE;
+}
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is enabled.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if active protocol is enabled
+*  - FALSE if active protocol is disabled
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsEnabled(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      return XHdcp1x_IsEnabled(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_22 :
+      return XHdcp22Tx_IsEnabled(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is authenticated.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if active protocol is authenticated
+*  - FALSE if active protocol is not authenticated
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsAuthenticated(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      return XHdcp1x_IsAuthenticated(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_22 :
+      return XHdcp22Tx_IsAuthenticated(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol has encryption enabled.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if active protocol has encryption enabled
+*  - FALSE if active protocol has encryption disabled
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsEncrypted(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      return XHdcp1x_IsEncrypted(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_22 :
+      return XHdcp22Tx_IsEncryptionEnabled(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is busy authenticating.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if active protocol is busy authenticating
+*  - FALSE if active protocol is not busy authenticating
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsInProgress(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      return XHdcp1x_IsInProgress(InstancePtr->Hdcp14Ptr);
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_22 :
+      return XHdcp22Tx_IsInProgress(InstancePtr->Hdcp22Ptr);
+#endif
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is in computations state.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if active protocol is in computations state
+*  - FALSE if active protocol is not in computations state
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsInComputations(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      return XHdcp1x_IsInComputations(InstancePtr->Hdcp14Ptr);
+#endif
+
+    case XV_HDMITXSS_HDCP_22 :
+      return FALSE;
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the active HDCP protocol is in wait-for-ready state.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*  - TRUE if active protocol is in computations state
+*  - FALSE if active protocol is not in computations state
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsInWaitforready(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      return FALSE;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14 :
+      return XHdcp1x_IsInWaitforready(InstancePtr->Hdcp14Ptr);
+#endif
+
+    case XV_HDMITXSS_HDCP_22 :
+      return FALSE;
+
+    default :
+      return FALSE;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function sets pointers to the HDCP 1.4 and HDCP 2.2 keys and
+* System Renewability Message (SRM).
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_HdcpSetKey(XV_HdmiTxSs *InstancePtr,
+                            XV_HdmiTxSs_HdcpKeyType KeyType,
+                            u8 *KeyPtr)
+{
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+  Xil_AssertVoid(KeyType <= XV_HDMITXSS_KEY_INVALID);
+
+  switch (KeyType) {
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2 LC128
+    case XV_HDMITXSS_KEY_HDCP22_LC128 :
+      InstancePtr->Hdcp22Lc128Ptr = KeyPtr;
+      break;
+
+    // HDCP 2.2 SRM
+    case XV_HDMITXSS_KEY_HDCP22_SRM :
+      InstancePtr->Hdcp22SrmPtr = KeyPtr;
+      break;
+#endif
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_KEY_HDCP14 :
+      InstancePtr->Hdcp14KeyPtr = KeyPtr;
+      break;
+
+    // HDCP 1.4 SRM
+    case XV_HDMITXSS_KEY_HDCP14_SRM :
+      InstancePtr->Hdcp14SrmPtr = KeyPtr;
+      break;
+#endif
+
+    default :
+      break;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function reports the HDCP info
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+* @param buff The buffer to print to
+* @param buff_size The size of the buffer
+
+* @return The number of bytes written to buff.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpInfo(XV_HdmiTxSs *InstancePtr, char *buff, int buff_size)
+{
+  int strSize = 0;
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  switch (InstancePtr->HdcpProtocol) {
+    case XV_HDMITXSS_HDCP_NONE :
+      strSize = scnprintf(buff+strSize, buff_size-strSize,
+          "\r\nHDCP TX is disabled\r\n");
+      break;
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14 :
+      if (InstancePtr->Hdcp14Ptr) {
+        if (XHdcp1x_IsEnabled(InstancePtr->Hdcp14Ptr)) {
+          strSize = scnprintf(buff+strSize, buff_size-strSize,
+              "\r\nHDCP 1.4 TX Info\r\n");
+
+          XDebug_SetDebugBufPrintf(buff,buff_size, &strSize);
+          XHdcp1x_Info(InstancePtr->Hdcp14Ptr);
+          XDebug_SetDebugBufPrintf(NULL,0, NULL);
+          // Route debug output to xil_printf
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+          XDebug_SetDebugPrintf((void *)printk);
+#else
+          XDebug_SetDebugPrintf((void *)_printk);
+#endif
+        }
+        else {
+          strSize = scnprintf(buff+strSize, buff_size-strSize,
+              "\r\nHDCP 1.4 TX is disabled\r\n");
+        }
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22 :
+      if (InstancePtr->Hdcp22Ptr) {
+        if (XHdcp22Tx_IsEnabled(InstancePtr->Hdcp22Ptr)) {
+          strSize = XHdcp22Tx_LogShow(InstancePtr->Hdcp22Ptr, buff, buff_size);
+
+          strSize += scnprintf(buff+strSize, buff_size-strSize,
+              "HDCP 2.2 TX Info\r\n");
+          XDebug_SetDebugBufPrintf(buff,buff_size, &strSize);
+          XHdcp22Tx_Info(InstancePtr->Hdcp22Ptr);
+          XDebug_SetDebugBufPrintf(NULL,0, NULL);
+          // Route debug output to xil_printf
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+          XDebug_SetDebugPrintf((void *)printk);
+#else
+          XDebug_SetDebugPrintf((void *)_printk);
+#endif
+        }
+        else {
+          strSize = scnprintf(buff+strSize, buff_size-strSize,
+              "\r\nHDCP 2.2 TX is disabled\r\n");
+        }
+      }
+      break;
+#endif
+
+    default:
+      strSize = scnprintf(buff+strSize, buff_size-strSize,
+          "\r\nHDCP Info Unknown?\r\n");
+      break;
+  }
+  return strSize;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function sets the logging level.
+*
+* @param  InstancePtr pointer to XV_HdmiTxSs instance
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_HdcpSetInfoDetail(XV_HdmiTxSs *InstancePtr, u8 Verbose)
+{
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+
+  if (Verbose) {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    if (InstancePtr->Hdcp14Ptr) {
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+      XHdcp1x_SetDebugLogMsg((void *)printk);
+#else
+      XHdcp1x_SetDebugLogMsg((void *)_printk);
+#endif
+    }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    if (InstancePtr->Hdcp22Ptr) {
+      XHdcp22Tx_LogReset(InstancePtr->Hdcp22Ptr, TRUE);
+    }
+#endif
+  } else {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    if (InstancePtr->Hdcp14Ptr) {
+      XHdcp1x_SetDebugLogMsg(NULL);
+    }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    if (InstancePtr->Hdcp22Ptr) {
+      XHdcp22Tx_LogReset(InstancePtr->Hdcp22Ptr, FALSE);
+    }
+#endif
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology for the active protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return Pointer to repeater topology structure.
+*
+* @note   None.
+*
+******************************************************************************/
+void *XV_HdmiTxSs_HdcpGetTopology(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  void *RepeaterTopologyPtr = NULL;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        RepeaterTopologyPtr = XHdcp1x_GetTopology(InstancePtr->Hdcp14Ptr);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        RepeaterTopologyPtr = XHdcp22Tx_GetTopology(InstancePtr->Hdcp22Ptr);
+      }
+      break;
+#endif
+
+    default:
+      RepeaterTopologyPtr = NULL;
+  }
+
+  return RepeaterTopologyPtr;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology list.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return Pointer to repeater topology list.
+*
+* @note   None.
+*
+******************************************************************************/
+u8 *XV_HdmiTxSs_HdcpGetTopologyReceiverIdList(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 *ListPtr = NULL;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        ListPtr = XHdcp1x_GetTopologyKSVList(InstancePtr->Hdcp14Ptr);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        ListPtr = XHdcp22Tx_GetTopologyReceiverIdList(InstancePtr->Hdcp22Ptr);
+      }
+      break;
+#endif
+
+    default:
+      ListPtr = NULL;
+  }
+
+  return ListPtr;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets various fields inside the HDCP repeater topology.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+* @param Field indicates what field of the topology structure to update.
+*
+* @return XST_SUCCESS or XST_FAILURE.
+*
+* @note   None.
+*
+******************************************************************************/
+u32 XV_HdmiTxSs_HdcpGetTopologyField(XV_HdmiTxSs *InstancePtr,
+                                     XV_HdmiTxSs_HdcpTopologyField Field)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+  Xil_AssertNonvoid(Field < XV_HDMITXSS_HDCP_TOPOLOGY_INVALID);
+
+  switch (Field)
+  {
+      case XV_HDMITXSS_HDCP_TOPOLOGY_DEPTH:
+      return XV_HdmiTxSs_HdcpGetTopologyDepth(InstancePtr);
+      case XV_HDMITXSS_HDCP_TOPOLOGY_DEVICECNT:
+      return XV_HdmiTxSs_HdcpGetTopologyDeviceCnt(InstancePtr);
+      case XV_HDMITXSS_HDCP_TOPOLOGY_MAXDEVSEXCEEDED:
+      return XV_HdmiTxSs_HdcpGetTopologyMaxDevsExceeded(InstancePtr);
+      case XV_HDMITXSS_HDCP_TOPOLOGY_MAXCASCADEEXCEEDED:
+      return XV_HdmiTxSs_HdcpGetTopologyMaxCascadeExceeded(InstancePtr);
+      case XV_HDMITXSS_HDCP_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM:
+      return XV_HdmiTxSs_HdcpGetTopologyHdcp2LegacyDeviceDownstream(InstancePtr);
+      case XV_HDMITXSS_HDCP_TOPOLOGY_HDCP1DEVICEDOWNSTREAM:
+      return XV_HdmiTxSs_HdcpGetTopologyHdcp1DeviceDownstream(InstancePtr);
+    default:
+      return 0;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology depth.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return Depth from the repeater topology table.
+*
+* @note   None.
+*
+******************************************************************************/
+static u32 XV_HdmiTxSs_HdcpGetTopologyDepth(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 Depth = 0;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // HDCP 1.4
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Depth = XHdcp1x_GetTopologyField(InstancePtr->Hdcp14Ptr,
+                  XHDCP1X_TOPOLOGY_DEPTH);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Depth = XHdcp22Tx_GetTopologyField(InstancePtr->Hdcp22Ptr,
+                  XHDCP22_TX_TOPOLOGY_DEPTH);
+      }
+      break;
+#endif
+
+    default :
+      Depth = 0;
+  }
+
+  return Depth;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology device count.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return Depth from the repeater topology table.
+*
+* @note   None.
+*
+******************************************************************************/
+static u32 XV_HdmiTxSs_HdcpGetTopologyDeviceCnt(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 DeviceCnt = 0;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        DeviceCnt = XHdcp1x_GetTopologyField(InstancePtr->Hdcp14Ptr,
+                      XHDCP1X_TOPOLOGY_DEVICECNT);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        DeviceCnt = XHdcp22Tx_GetTopologyField(InstancePtr->Hdcp22Ptr,
+                      XHDCP22_TX_TOPOLOGY_DEVICECNT);
+      }
+      break;
+#endif
+
+    default:
+      DeviceCnt = 0;
+  }
+
+  return DeviceCnt;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology maximum devices exceeded
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*   - TRUE if maximum devices exceeded.
+*   - FALSE if maximum devices not exceeded.
+*
+* @note   None.
+*
+******************************************************************************/
+static u8 XV_HdmiTxSs_HdcpGetTopologyMaxDevsExceeded(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 Flag = FALSE;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Flag = XHdcp1x_GetTopologyField(InstancePtr->Hdcp14Ptr,
+                 XHDCP1X_TOPOLOGY_MAXDEVSEXCEEDED);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Flag = XHdcp22Tx_GetTopologyField(InstancePtr->Hdcp22Ptr,
+                 XHDCP22_TX_TOPOLOGY_MAXDEVSEXCEEDED);
+      }
+      break;
+#endif
+
+    default:
+      Flag = FALSE;
+  }
+
+  return Flag;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology maximum cascade exceeded
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*   - TRUE if maximum cascade exceeded.
+*   - FALSE if maximum cascade not exceeded.
+*
+* @note   None.
+*
+******************************************************************************/
+static
+u8 XV_HdmiTxSs_HdcpGetTopologyMaxCascadeExceeded(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 Flag = FALSE;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Flag = XHdcp1x_GetTopologyField(InstancePtr->Hdcp14Ptr,
+                 XHDCP1X_TOPOLOGY_MAXCASCADEEXCEEDED);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Flag = XHdcp22Tx_GetTopologyField(InstancePtr->Hdcp22Ptr,
+                XHDCP22_TX_TOPOLOGY_MAXCASCADEEXCEEDED);
+      }
+      break;
+#endif
+
+    default:
+      Flag = FALSE;
+  }
+
+  return Flag;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology HDCP2 Legacy Device downstream
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*   - TRUE if HDCP2 legacy device is downstream.
+*   - FALSE if HDCP2 legacy device is not downstream.
+*
+* @note   None.
+*
+******************************************************************************/
+static
+u8 XV_HdmiTxSs_HdcpGetTopologyHdcp2LegacyDeviceDownstream(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 Flag = FALSE;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Flag = FALSE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Flag = XHdcp22Tx_GetTopologyField(InstancePtr->Hdcp22Ptr,
+                 XHDCP22_TX_TOPOLOGY_HDCP2LEGACYDEVICEDOWNSTREAM);
+      }
+      break;
+#endif
+
+    default:
+      Flag = FALSE;
+  }
+
+  return Flag;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function gets the HDCP repeater topology HDCP 1.x device downstream
+* flag.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*   - TRUE if HDCP 1.x device is downstream.
+*   - FALSE if HDCP 1.x device is not downstream.
+*
+* @note   None.
+*
+******************************************************************************/
+static
+   u8 XV_HdmiTxSs_HdcpGetTopologyHdcp1DeviceDownstream(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  u8 Flag = FALSE;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Flag = TRUE;
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Flag = XHdcp22Tx_GetTopologyField(InstancePtr->Hdcp22Ptr,
+                 XHDCP22_TX_TOPOLOGY_HDCP1DEVICEDOWNSTREAM);
+      }
+      break;
+#endif
+
+    default:
+      Flag = FALSE;
+  }
+
+  return Flag;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function sets the HDCP repeater content stream management type.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return None.
+*
+* @note   None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_HdcpSetContentStreamType(XV_HdmiTxSs *InstancePtr,
+       XV_HdmiTxSs_HdcpContentStreamType StreamType)
+{
+  /* Verify argument. */
+  Xil_AssertVoid(InstancePtr != NULL);
+  Xil_AssertVoid(StreamType <= XV_HDMITXSS_HDCP_STREAMTYPE_1);
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      break;
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        XHdcp22Tx_SetContentStreamType(InstancePtr->Hdcp22Ptr,
+                                       (XHdcp22_Tx_ContentStreamType) StreamType);
+      }
+      break;
+#endif
+
+    default:
+      break;
+  }
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function checks if the HDMI transmitter is an HDCP repeater
+* downstream interface for the active protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+*
+* @return
+*   - TRUE if repeater downstream interface.
+*   - FALSE if not repeater downstream interface.
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpIsRepeater(XV_HdmiTxSs *InstancePtr)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+  int Status = (int)FALSE;
+
+  switch (InstancePtr->HdcpProtocol)
+  {
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+    // HDCP 1.4
+    case XV_HDMITXSS_HDCP_14:
+      if (InstancePtr->Hdcp14Ptr) {
+        Status = XHdcp1x_IsRepeater(InstancePtr->Hdcp14Ptr);
+      }
+      break;
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+    // HDCP 2.2
+    case XV_HDMITXSS_HDCP_22:
+      if (InstancePtr->Hdcp22Ptr) {
+        Status = XHdcp22Tx_IsRepeater(InstancePtr->Hdcp22Ptr);
+      }
+      break;
+#endif
+
+    default:
+      Status = (int)FALSE;
+  }
+
+  return Status;
+}
+#endif
+
+#ifdef USE_HDCP_TX
+/*****************************************************************************/
+/**
+*
+* This function enables the Repeater functionality for the HDCP protocol.
+*
+* @param InstancePtr is a pointer to the XV_HdmiTxSs instance.
+* @param Set is TRUE to enable and FALSE to disable repeater.
+*
+* @return
+*  - XST_SUCCESS if action was successful
+*  - XST_FAILURE if action was not successful
+*
+* @note   None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_HdcpSetRepeater(XV_HdmiTxSs *InstancePtr, u8 Set)
+{
+  /* Verify argument. */
+  Xil_AssertNonvoid(InstancePtr != NULL);
+
+#ifdef XPAR_XHDCP_NUM_INSTANCES
+  // HDCP 1.4
+  if (InstancePtr->Hdcp14Ptr) {
+    XHdcp1x_SetRepeater(InstancePtr->Hdcp14Ptr, Set);
+  }
+#endif
+
+#ifdef XPAR_XHDCP22_TX_NUM_INSTANCES
+  // HDCP 2.2
+  if (InstancePtr->Hdcp22Ptr) {
+    XHdcp22Tx_SetRepeater(InstancePtr->Hdcp22Ptr, Set);
+  }
+#endif
+
+  return XST_SUCCESS;
+}
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_log.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xv_hdmitxss_log.c
@@ -0,0 +1,307 @@
+/*******************************************************************************
+ *
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+*******************************************************************************/
+/******************************************************************************/
+/**
+ *
+ * @file xv_hdmitxss_log.c
+ *
+ *
+ * @note	None.
+ *
+ * <pre>
+ * MODIFICATION HISTORY:
+ *
+ * Ver   Who  Date     Changes
+ * ----- ---- -------- -----------------------------------------------
+ * 1.0   YH   17/08/16 Initial release.
+ * 1.01  MMO  03/01/17 Add compiler option(XV_HDMITXSS_LOG_ENABLE) to enable Log
+ * 5.0   EB   16/01/18 Added new log XV_HDMITXSS_LOG_EVT_PIX_REPEAT_ERR
+ *            23/01/18 Minor cleanup
+ * </pre>
+ *
+*******************************************************************************/
+
+/******************************* Include Files ********************************/
+
+#include "xv_hdmitxss.h"
+
+/**************************** Function Prototypes *****************************/
+
+/**************************** Function Definitions ****************************/
+
+/*****************************************************************************/
+/**
+* This function will reset the driver's logging mechanism.
+*
+* @param	InstancePtr is a pointer to the xv_hdmitxss core instance.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+#ifdef XV_HDMITXSS_LOG_ENABLE
+void XV_HdmiTxSs_LogReset(XV_HdmiTxSs *InstancePtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	InstancePtr->Log.HeadIndex = 0;
+	InstancePtr->Log.TailIndex = 0;
+}
+
+/*****************************************************************************/
+/**
+* This function will insert an event in the driver's logginc mechanism.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	Evt is the event type to log.
+* @param	Data is the associated data for the event.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XV_HdmiTxSs_LogWrite(XV_HdmiTxSs *InstancePtr, XV_HdmiTxSs_LogEvent Evt, u8 Data)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(Evt <= (XV_HDMITXSS_LOG_EVT_DUMMY));
+	Xil_AssertVoid(Data < 0xFF);
+
+	/* Write data and event into log buffer */
+	InstancePtr->Log.DataBuffer[InstancePtr->Log.HeadIndex] =
+			(Data << 8) | Evt;
+
+	/* Update head pointer if reached to end of the buffer */
+	if (InstancePtr->Log.HeadIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) / sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+		/* Clear pointer */
+		InstancePtr->Log.HeadIndex = 0;
+	}
+	else {
+		/* Increment pointer */
+		InstancePtr->Log.HeadIndex++;
+	}
+
+	/* Check tail pointer. When the two pointer are equal, then the buffer
+	 * is full. In this case then increment the tail pointer as well to
+	 * remove the oldest entry from the buffer. */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) / sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+}
+
+/*****************************************************************************/
+/**
+* This function will read the last event from the log.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+*
+* @return	The log data.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XV_HdmiTxSs_LogRead(XV_HdmiTxSs *InstancePtr)
+{
+	u16 Log;
+
+	/* Verify argument. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Check if there is any data in the log */
+	if (InstancePtr->Log.TailIndex == InstancePtr->Log.HeadIndex) {
+		Log = 0;
+	}
+	else {
+		Log = InstancePtr->Log.DataBuffer[InstancePtr->Log.TailIndex];
+
+		/* Increment tail pointer */
+		if (InstancePtr->Log.TailIndex ==
+			(u8)((sizeof(InstancePtr->Log.DataBuffer) / sizeof(InstancePtr->Log.DataBuffer[0])) - 1)) {
+			InstancePtr->Log.TailIndex = 0;
+		}
+		else {
+			InstancePtr->Log.TailIndex++;
+		}
+	}
+
+	return Log;
+}
+#endif
+
+/*****************************************************************************/
+/**
+* This function will print the entire log to the passed buffer.
+*
+* @param	InstancePtr is a pointer to the XV_HdmiTxSs core instance.
+* @param	buff Buffer to print to
+* @param	buff_size size off buff passed
+*
+* @return	The number of characters written to buff.
+*
+* @note		None.
+*
+******************************************************************************/
+int XV_HdmiTxSs_LogShow(XV_HdmiTxSs *InstancePtr, char *buff, int buff_size)
+{
+	int strSize = 0;
+#ifdef XV_HDMITXSS_LOG_ENABLE
+	u16 Log;
+	u8 Evt;
+	u8 Data;
+
+	/* Verify argument. */
+	Xil_AssertVoid(InstancePtr != NULL);
+
+	strSize = scnprintf(buff+strSize, buff_size-strSize,
+			"\r\n\n\nHDMI TX log\r\n" \
+			"------\r\n");
+
+	/* Read log data */
+	Log = XV_HdmiTxSs_LogRead(InstancePtr);
+
+	while (Log != 0 && (buff_size - strSize) > 30 ) {
+		/* Event */
+		Evt = Log & 0xff;
+
+		/* Data */
+		Data = (Log >> 8) & 0xFF;
+
+		switch (Evt) {
+		case (XV_HDMITXSS_LOG_EVT_NONE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"HDMI TXSS log end\r\n-------\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_HDMITX_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing HDMI TX core....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_VTC_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing VTC core....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_HDCPTIMER_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing AXI Timer core....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_HDCP14_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing HDCP 1.4 core....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_HDCP22_INIT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Initializing HDCP 2.2 core....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_START):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Start HDMI TX Subsystem....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_STOP):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Stop HDMI TX Subsystem....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_RESET):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Reset HDMI TX Subsystem....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_CONNECT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX cable is connected....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_DISCONNECT):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX cable is disconnected....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_TOGGLE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX cable is toggled....\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_STREAMUP):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Stream is Up\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_STREAMDOWN):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Stream is Down\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_STREAMSTART):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Stream Start\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_SETAUDIOCHANNELS):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Set Audio Channels (%0d)\r\n", Data);
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_AUDIOMUTE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Audio Muted\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_AUDIOUNMUTE):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Audio Unmuted\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_SETSTREAM):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX Set Stream, with video mode (%0d)\r\n", Data);
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_HDCP14_AUTHREQ):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX HDCP 1.4 authentication request\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_HDCP22_AUTHREQ):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"TX HDCP 2.2 authentication request\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_PIX_REPEAT_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Unsupported Pixel Repetition: %d\r\n", Data);
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_VTC_RES_ERR):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Unsupported Video by VTC\r\n");
+			break;
+	    case (XV_HDMITXSS_LOG_EVT_BRDG_UNLOCKED):
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"VID Bridge Unlocked\r\n");
+			break;
+		default:
+			strSize += scnprintf(buff+strSize, buff_size-strSize,
+					"Unknown event: %i\r\n", Data);
+			break;
+		}
+
+		if((buff_size - strSize) > 30) {
+	        /* Read log data */
+	        Log = XV_HdmiTxSs_LogRead(InstancePtr);
+		} else {
+			Log = 0;
+		}
+	}
+#else
+	strSize += scnprintf(buff+strSize, buff_size-strSize,
+			"\r\n INFO:: HDMITXSS Log Feature is Disabled \r\n");
+#endif
+    return strSize;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc.c
@@ -0,0 +1,2649 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xvtc.c
+* @{
+*
+* This is main code of Xilinx MVI Video Timing Controller (VTC) device driver.
+* The VTC device detects and generates video sync signals to Video IP cores
+* like MVI Video Scaler. Please see xvtc.h for more details of the driver.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00a xd     08/05/08 First release.
+* 1.01a xd     07/23/10 Added GIER; Added more h/w generic info into
+*                       xparameters.h; Feed callbacks with pending
+*                       interrupt info. Added Doxygen & Version support.
+* 3.00a cjm    08/01/12 Converted from xio.h to xil_io.h, translating
+*                       basic types, MB cache functions, exceptions and
+*                       assertions to xil_io format.
+*                       Replaced the following:
+*                       "XExc_Init" -> "Xil_ExceptionInit"
+*                       "XExc_RegisterHandler" ->
+*                       "Xil_ExceptionRegisterHandler"
+*                       "XEXC_ID_NON_CRITICAL_INT" -> "XIL_EXCEPTION_ID_INT"
+*                       "XExceptionHandler" -> "Xil_ExceptionHandler"
+*                       "XExc_mEnableExceptions" -> "Xil_ExceptionEnable"
+*                       "XEXC_NON_CRITICAL" -> "XIL_EXCEPTION_NON_CRITICAL"
+*                       "XExc_DisableExceptions" -> "Xil_ExceptionDisable"
+*                       "XExc_RemoveHandler" -> "Xil_ExceptionRemoveHandler"
+*                       "microblaze_enable_interrupts" -> "Xil_ExceptionEnable"
+*                       "microblaze_disable_interrupts" ->
+*                       Xil_ExceptionDisable"
+*                       "XCOMPONENT_IS_STARTED" -> "XIL_COMPONENT_IS_STARTED"
+*                       "XCOMPONENT_IS_READY" -> "(XIL_COMPONENT_IS_READY)"
+*
+*                       "XASSERT_NONVOID" -> "Xil_AssertNonvoid"
+*                       "XASSERT_VOID_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XASSERT_VOID" -> "Xil_AssertVoid"
+*                       "Xil_AssertVoid_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XAssertStatus" -> "Xil_AssertStatus"
+*                       "XAssertSetCallback" -> "Xil_AssertCallback"
+*
+*                       "XASSERT_OCCURRED" -> "XIL_ASSERT_OCCURRED"
+*                       "XASSERT_NONE" -> "XIL_ASSERT_NONE"
+*
+*                       "microblaze_disable_dcache" -> "Xil_DCacheDisable"
+*                       "microblaze_enable_dcache" -> "Xil_DCacheEnable"
+*                       "microblaze_enable_icache" -> "Xil_ICacheEnable"
+*                       "microblaze_disable_icache" -> "Xil_ICacheDisable"
+*                       "microblaze_init_dcache_range" ->
+*                       "Xil_DCacheInvalidateRange"
+*                       "XCache_DisableDCache" -> "Xil_DCacheDisable"
+*                       "XCache_DisableICache" -> "Xil_ICacheDisable"
+*                       "XCache_EnableDCache" -> "Xil_DCacheEnableRegion"
+*                       "XCache_EnableICache" -> "Xil_ICacheEnableRegion"
+*                       "XCache_InvalidateDCacheLine" ->
+*                       "Xil_DCacheInvalidateRange"
+*
+*                       "XUtil_MemoryTest32" -> "Xil_TestMem32"
+*                       "XUtil_MemoryTest16" -> "Xil_TestMem16"
+*                       "XUtil_MemoryTest8" -> "Xil_TestMem8"
+*
+*                       "xutil.h" -> "xil_testmem.h"
+*
+*                       "xbasic_types.h" -> "xil_types.h"
+*                       "xio.h" -> "xil_io.h"
+*
+*                       "XIo_In32" -> "Xil_In32"
+*                       "XIo_Out32" -> "Xil_Out32"
+*
+*                       "XTRUE" -> "TRUE"
+*                       "XFALSE" -> "FALSE"
+*                       "XNULL" -> "NULL"
+*
+*                       "Xuint8" -> "u8"
+*                       "Xuint16" -> "u16"
+*                       "Xuint32" -> "u32"
+*                       "Xint8" -> "char"
+*                       "Xint16" -> "short"
+*                       "Xint32" -> "long"
+*                       "Xfloat32" -> "float"
+*                       "Xfloat64" -> "double"
+*                       "Xboolean" -> "int"
+*                       "XTEST_FAILED" -> "XST_FAILURE"
+*                       "XTEST_PASSED" -> "XST_SUCCESS"
+* 4.00a cjm    02/08/13 Removed XVTC_CTL_HASS_MASK
+* 5.00a cjm    08/07/13 Replaced CTL in Polarity and Encoding register
+*                       definition with "POL" and "ENC"
+* 5.00a cjm    10/30/13 Removed type parameter from XVtc_Enable which now
+*                       enables both generator and detector.
+*                       Added XVtc_EnableGenerator to enable only the Generator
+*                       Added XVtc_EnableDetector to enable only the Detector
+* 5.00a cjm    11/01/13 Added Timing, VideoMode and Signal Conversion Functions
+*                       XVtc_ConvVideoMode2Timing
+*                       XVtc_ConvTiming2Signal
+*                       XVtc_ConvSignal2Timing
+*                       XVtc_ConvTiming2VideoMode
+*                       Added Timing and Video Mode Set/Get Functions
+*                       XVtc_SetGeneratorTiming
+*                       XVtc_SetGeneratorVideoMode
+*                       XVtc_GetGeneratorTiming
+*                       XVtc_GetGeneratorVideoMode
+*                       XVtc_GetDetectorTiming
+*                       XVtc_GetDetectorVideoMode
+*                       Updated XVtc_GetGeneratorHoriOffset and
+*                       XVtc_SetGeneratorHoriOffset. For adding interlaced or
+*                       field-1 registers setting/getting updated
+*                       XVtc_SetGenerator to align vsync to hsync
+*                       horizontally by default.
+*                       Added Field 1 set/get to XVtc_SetGenerator,
+*                       XVtc_GetGenerator and XVtc_GetDetector.
+* 5.00a cjm    11/03/13 Added Chroma/field parity bit masks.
+*                       Replaced old timing bit masks/shifts with Start/End Bit
+*                       masks/shifts.
+* 6.1   adk    08/23/14 Modified HActiveVideo value to 1920 for
+*                       XVTC_VMODE_1080I mode.
+*                       Removed Major, Minor and Revision parameters from
+*                       XVtc_GetVersion.
+*                       Modified return type of XVtc_GetVersion from
+*                       void to u32.
+* 7.0   vns    25/02/15 Added progressive and interlaced mode switching feature.
+*                       Modified XVtc_SetGenerator, XVtc_GetGenerator,
+*                       XVtc_GetDetector, XVtc_ConvTiming2Signal and
+*                       XVtc_ConvSignal2Timing APIs
+* 7.1   vns    07/10/15 Corrected V0SyncStart and V1SyncStart values
+*                       in APIs XVtc_ConvTiming2Signal and
+*                       XVtc_ConvSignal2Timing
+*                       Corrected register read to XVTC_DVSYNC_F1_OFFSET
+*                       in API XVtc_GetDetector
+*       vns    10/14/15 Modified XVtc_SetSource API to provided programming
+*                       interlaced mode feature and modified XVtc_GetSource
+*                       API to read interlaced mode status.
+*                       Corrected XVtc_ConvSignal2Timing API to get interlaced
+*                       mode from SignalCfgPtr structure.
+* 7.2   mh     04/20/16 Removed call to XVtc_Reset from XVtc_CfgInitialize.
+*       sk     08/16/16 Used UINTPTR instead of u32 for Baseaddress as part of
+*                       adding 64 bit support. CR# 867425.
+*                       Changed the prototype of XVtc_CfgInitialize API.
+* 8.0   jsr    07/03/18	Added a new register XVTC_GASIZE_F1_OFFSET for interlaced
+*       		modes FIELD1 vactive size. This value is same as FILED0
+*       		vactive size for all interlaced modes except for SDI NTSC
+*       		mode
+*	jsr    10/01/18	Removed the hard coded programming of vactive size values
+* 			based on resolutions. Moved the hard coded values for SDI
+* 			NTSC resolution to SDI TXSS driver instead of in VTC
+* 			driver.
+* 	jsr    10/03/18	Corrected the VGA resoultion timing paramters w.r.t the
+* 			timing values given in the VTC GUI for 640x480p
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xvtc.h"
+#include <linux/string.h>
+//#include "xenv.h"
+#include "xil_printf.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/************************** Function Prototypes ******************************/
+
+/*
+* Each of callback functions to be called on different types of interrupts.
+* These stub functions are set during XVtc_CfgInitialize as default
+* callback functions. If application is not registered any of the callback
+* function, these functions will be called for doing nothing.
+*/
+static void StubCallBack(void *CallBackRef, u32 Mask);
+static void StubErrCallBack(void *CallBackRef, u32 ErrorMask);
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function initializes the VTC core. This function must be called
+* prior to using the VTC core. Initialization of the VTC includes setting up
+* the instance data, and ensuring the hardware is in a quiescent state.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+* @param	CfgPtr points to the configuration structure associated with
+*		the VTC core.
+* @param	EffectiveAddr is the base address of the device. If address
+*		translation is being used, then this parameter must reflect the
+*		virtual base address. Otherwise, the physical address should be
+*		used.
+*
+* @return
+*		- XST_SUCCESS if XVtc_CfgInitialize was successful.
+*
+* @note		None.
+*
+******************************************************************************/
+int XVtc_CfgInitialize(XVtc *InstancePtr, XVtc_Config *CfgPtr,
+				UINTPTR EffectiveAddr)
+{
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(CfgPtr != NULL);
+	Xil_AssertNonvoid((u32 *)EffectiveAddr != NULL);
+
+	/* Setup the instance */
+	memset((void *)InstancePtr, 0, sizeof(XVtc));
+
+	memcpy((void *)&(InstancePtr->Config), (const void *)CfgPtr,
+			   sizeof(XVtc_Config));
+	InstancePtr->Config.BaseAddress = EffectiveAddr;
+
+	/* Set all handlers to stub values, let user configure this data later */
+	InstancePtr->FrameSyncCallBack = (XVtc_CallBack) StubCallBack;
+	InstancePtr->LockCallBack = (XVtc_CallBack) StubCallBack;
+	InstancePtr->DetectorCallBack = (XVtc_CallBack) StubCallBack;
+	InstancePtr->GeneratorCallBack = (XVtc_CallBack) StubCallBack;
+	InstancePtr->ErrCallBack = (XVtc_ErrorCallBack) StubErrCallBack;
+
+	/* Set the flag to indicate the driver is ready */
+	InstancePtr->IsReady = (u32)(XIL_COMPONENT_IS_READY);
+
+	return XST_SUCCESS;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the VTC Generator core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_EnableGenerator(XVtc *InstancePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Change the value according to the enabling type and write it back */
+	CtrlRegValue |= XVTC_CTL_GE_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+			CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the VTC Detector core
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_EnableDetector(XVtc *InstancePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Change the value according to the enabling type and write it back */
+	CtrlRegValue |= XVTC_CTL_DE_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+			CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function enables the Detector and Generator at same time of the
+* VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_Enable(XVtc *InstancePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Setup the SW Enable Bit and write it back */
+	CtrlRegValue |= XVTC_CTL_SW_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+				CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the VTC Generator core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_DisableGenerator(XVtc *InstancePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Change the value according to the disabling type and write it
+	 * back
+	 */
+	CtrlRegValue &= (u32)(~(XVTC_CTL_GE_MASK));
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+			CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the VTC Detector core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_DisableDetector(XVtc *InstancePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Change the value according to the disabling type and write it
+	 * back
+	 */
+	CtrlRegValue &= (u32)(~(XVTC_CTL_DE_MASK));
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+			CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function disables the Detector and Generator at same time of the VTC
+* core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_Disable(XVtc *InstancePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Change the value, clearing Core Enable, and write it back*/
+	CtrlRegValue &= ~XVTC_CTL_SW_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+			CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the output polarity of the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	PolarityPtr points to a Polarity configuration structure with
+*		the setting to use on the VTC core.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void XVtc_SetPolarity(XVtc *InstancePtr, XVtc_Polarity *PolarityPtr)
+{
+	u32 PolRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(PolarityPtr != NULL);
+
+	/* Read Control register value back and clear all polarity
+	 * bits first
+	 */
+	PolRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_GPOL_OFFSET));
+	PolRegValue &= (u32)(~(XVTC_POL_ALLP_MASK));
+
+	/* Change the register value according to the setting in the Polarity
+	 * configuration structure
+	 */
+	if (PolarityPtr->ActiveChromaPol)
+		PolRegValue |= XVTC_POL_ACP_MASK;
+
+	if (PolarityPtr->ActiveVideoPol)
+		PolRegValue |= XVTC_POL_AVP_MASK;
+
+	if (PolarityPtr->FieldIdPol)
+		PolRegValue |= XVTC_POL_FIP_MASK;
+
+	if (PolarityPtr->VBlankPol)
+		PolRegValue |= XVTC_POL_VBP_MASK;
+
+	if (PolarityPtr->VSyncPol)
+		PolRegValue |= XVTC_POL_VSP_MASK;
+
+	if (PolarityPtr->HBlankPol)
+		PolRegValue |= XVTC_POL_HBP_MASK;
+
+	if (PolarityPtr->HSyncPol)
+		PolRegValue |= XVTC_POL_HSP_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_GPOL_OFFSET),
+			PolRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the output polarity setting used by the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	PolarityPtr points to a Polarity configuration structure that
+*		will be populated with the setting used on the VTC core
+*		after this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetPolarity(XVtc *InstancePtr, XVtc_Polarity *PolarityPtr)
+{
+	u32 PolRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(PolarityPtr != NULL);
+
+	/* Clear the Polarity configuration structure */
+	memset((void *)PolarityPtr, 0, sizeof(XVtc_Polarity));
+
+	/* Read Control register value back */
+	PolRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_GPOL_OFFSET));
+
+	/* Populate the Polarity configuration structure w/ the current setting
+	 * used in the device
+	 */
+	if (PolRegValue & XVTC_POL_ACP_MASK)
+		PolarityPtr->ActiveChromaPol = 1;
+
+	if (PolRegValue & XVTC_POL_AVP_MASK)
+		PolarityPtr->ActiveVideoPol = 1;
+
+	if (PolRegValue & XVTC_POL_FIP_MASK)
+		PolarityPtr->FieldIdPol = 1;
+
+	if (PolRegValue & XVTC_POL_VBP_MASK)
+		PolarityPtr->VBlankPol = 1;
+
+	if (PolRegValue & XVTC_POL_VSP_MASK)
+		PolarityPtr->VSyncPol = 1;
+
+	if (PolRegValue & XVTC_POL_HBP_MASK)
+		PolarityPtr->HBlankPol = 1;
+
+	if (PolRegValue & XVTC_POL_HSP_MASK)
+		PolarityPtr->HSyncPol = 1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the input polarity setting used by the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	PolarityPtr points to a Polarity configuration structure that
+*		will be populated with the setting used on the VTC core after
+*		this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetDetectorPolarity(XVtc *InstancePtr, XVtc_Polarity *PolarityPtr)
+{
+	u32 PolRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(PolarityPtr != NULL);
+
+	/* Clear the Polarity configuration structure */
+	memset((void *)PolarityPtr, 0, sizeof(XVtc_Polarity));
+
+	/* Read Control register value back */
+	PolRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_DPOL_OFFSET));
+
+	/* Populate the Polarity configuration structure w/ the current setting
+	 * used in the core.
+	 */
+	if (PolRegValue & XVTC_POL_ACP_MASK)
+		PolarityPtr->ActiveChromaPol = 1;
+
+	if (PolRegValue & XVTC_POL_AVP_MASK)
+		PolarityPtr->ActiveVideoPol = 1;
+
+	if (PolRegValue & XVTC_POL_FIP_MASK)
+		PolarityPtr->FieldIdPol = 1;
+
+	if (PolRegValue & XVTC_POL_VBP_MASK)
+		PolarityPtr->VBlankPol = 1;
+
+	if (PolRegValue & XVTC_POL_VSP_MASK)
+		PolarityPtr->VSyncPol = 1;
+
+	if (PolRegValue & XVTC_POL_HBP_MASK)
+		PolarityPtr->HBlankPol = 1;
+
+	if (PolRegValue & XVTC_POL_HSP_MASK)
+		PolarityPtr->HSyncPol = 1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the source selecting of the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on
+* @param 	SourcePtr points to a Source Selecting configuration structure
+*		with the setting to use on the VTC device.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetSource(XVtc *InstancePtr, XVtc_SourceSelect *SourcePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(SourcePtr != NULL);
+
+	/* Read Control register value back and clear all source selection bits
+	 * first
+	 */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+	CtrlRegValue &= ~XVTC_CTL_ALLSS_MASK;
+
+	/* Change the register value according to the setting in the source
+	 * selection configuration structure
+	 */
+
+	if (SourcePtr->FieldIdPolSrc)
+		CtrlRegValue |= XVTC_CTL_FIPSS_MASK;
+
+	if (SourcePtr->ActiveChromaPolSrc)
+		CtrlRegValue |= XVTC_CTL_ACPSS_MASK;
+
+	if (SourcePtr->ActiveVideoPolSrc)
+		CtrlRegValue |= XVTC_CTL_AVPSS_MASK;
+
+	if (SourcePtr->HSyncPolSrc)
+		CtrlRegValue |= XVTC_CTL_HSPSS_MASK;
+
+	if (SourcePtr->VSyncPolSrc)
+		CtrlRegValue |= XVTC_CTL_VSPSS_MASK;
+
+	if (SourcePtr->HBlankPolSrc)
+		CtrlRegValue |= XVTC_CTL_HBPSS_MASK;
+
+	if (SourcePtr->VBlankPolSrc)
+		CtrlRegValue |= XVTC_CTL_VBPSS_MASK;
+
+
+	if (SourcePtr->VChromaSrc)
+		CtrlRegValue |= XVTC_CTL_VCSS_MASK;
+
+	if (SourcePtr->VActiveSrc)
+		CtrlRegValue |= XVTC_CTL_VASS_MASK;
+
+	if (SourcePtr->VBackPorchSrc)
+		CtrlRegValue |= XVTC_CTL_VBSS_MASK;
+
+	if (SourcePtr->VSyncSrc)
+		CtrlRegValue |= XVTC_CTL_VSSS_MASK;
+
+	if (SourcePtr->VFrontPorchSrc)
+		CtrlRegValue |= XVTC_CTL_VFSS_MASK;
+
+	if (SourcePtr->VTotalSrc)
+		CtrlRegValue |= XVTC_CTL_VTSS_MASK;
+
+	if (SourcePtr->HBackPorchSrc)
+		CtrlRegValue |= XVTC_CTL_HBSS_MASK;
+
+	if (SourcePtr->HSyncSrc)
+		CtrlRegValue |= XVTC_CTL_HSSS_MASK;
+
+	if (SourcePtr->HFrontPorchSrc)
+		CtrlRegValue |= XVTC_CTL_HFSS_MASK;
+
+	if (SourcePtr->HTotalSrc)
+		CtrlRegValue |= XVTC_CTL_HTSS_MASK;
+
+	if (SourcePtr->InterlacedMode)
+		CtrlRegValue |= XVTC_CTL_INTERLACE_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_CTL_OFFSET),
+			CtrlRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the source select setting used by the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param 	SourcePtr points to a source select configuration structure
+*		that will be populated with the setting used on the VTC core
+*		after this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void XVtc_GetSource(XVtc *InstancePtr, XVtc_SourceSelect *SourcePtr)
+{
+	u32 CtrlRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(SourcePtr != NULL);
+
+	/* Clear the source selection configuration structure */
+	memset((void *)SourcePtr, 0, sizeof(XVtc_SourceSelect));
+
+	/* Read Control register value back */
+	CtrlRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					(XVTC_CTL_OFFSET));
+
+	/* Populate the source select configuration structure with the current
+	 * setting used in the core
+	 */
+	if (CtrlRegValue & XVTC_CTL_FIPSS_MASK)
+		SourcePtr->FieldIdPolSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_ACPSS_MASK)
+		SourcePtr->ActiveChromaPolSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_AVPSS_MASK)
+		SourcePtr->ActiveVideoPolSrc= 1;
+	if (CtrlRegValue & XVTC_CTL_HSPSS_MASK)
+		SourcePtr->HSyncPolSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VSPSS_MASK)
+		SourcePtr->VSyncPolSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_HBPSS_MASK)
+		SourcePtr->HBlankPolSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VBPSS_MASK)
+		SourcePtr->VBlankPolSrc = 1;
+
+	if (CtrlRegValue & XVTC_CTL_VCSS_MASK)
+		SourcePtr->VChromaSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VASS_MASK)
+		SourcePtr->VActiveSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VBSS_MASK)
+		SourcePtr->VBackPorchSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VSSS_MASK)
+		SourcePtr->VSyncSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VFSS_MASK)
+		SourcePtr->VFrontPorchSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_VTSS_MASK)
+		SourcePtr->VTotalSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_HBSS_MASK)
+		SourcePtr->HBackPorchSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_HSSS_MASK)
+		SourcePtr->HSyncSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_HFSS_MASK)
+		SourcePtr->HFrontPorchSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_HTSS_MASK)
+		SourcePtr->HTotalSrc = 1;
+	if (CtrlRegValue & XVTC_CTL_INTERLACE_MASK)
+		SourcePtr->InterlacedMode = 1;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the line skip setting of the Generator in the VTC
+* core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param 	GeneratorChromaSkip indicates whether to skip 1 line between
+*		active chroma for the Generator module. Use Non-0 value for
+*		this parameter to skip 1 line, and 0 to not skip lines.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetSkipLine(XVtc *InstancePtr, int GeneratorChromaSkip)
+{
+	u32 FrameEncodeRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Read Control register value back and clear all skip bits first */
+	FrameEncodeRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						(XVTC_GFENC_OFFSET));
+	FrameEncodeRegValue &= (u32)(~(XVTC_ENC_GACLS_MASK));
+
+	/* Change the register value according to the skip setting passed
+	 * into this function.
+	 */
+	if (GeneratorChromaSkip)
+		FrameEncodeRegValue |= XVTC_ENC_GACLS_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_GFENC_OFFSET),
+			FrameEncodeRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the line skip setting used by the Generator in the VTC
+* core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	GeneratorChromaSkipPtr will point to the value indicating
+*		whether one line is skipped between active chroma for the
+*		Generator module after this function returns. Value 1 means
+*		that 1 line is skipped and zero means that no lines are
+*		skipped.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetSkipLine(XVtc *InstancePtr, int *GeneratorChromaSkipPtr)
+{
+	u32 FrameEncodeRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(GeneratorChromaSkipPtr != NULL);
+
+	/* Read Control register value back */
+	FrameEncodeRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						(XVTC_GFENC_OFFSET));
+
+	/* Populate the skip variable values according to the skip setting
+	 * used by the core.
+	 */
+	if (FrameEncodeRegValue & XVTC_ENC_GACLS_MASK)
+		*GeneratorChromaSkipPtr = 1;
+	else
+		*GeneratorChromaSkipPtr = 0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the pixel skip setting of the Generator in the VTC
+* core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	GeneratorChromaSkip indicates whether to skip 1 pixel between
+*		active chroma for the Generator module. Use Non-0 value for
+*		this parameter to skip 1 pixel, and 0 to not skip pixels
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetSkipPixel(XVtc *InstancePtr, int GeneratorChromaSkip)
+{
+	u32 FrameEncodeRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == (u32)(XIL_COMPONENT_IS_READY));
+
+	/* Read Control register value back and clear all skip bits first */
+	FrameEncodeRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						(XVTC_GFENC_OFFSET));
+	FrameEncodeRegValue &= (u32)(~(XVTC_ENC_GACPS_MASK));
+
+	/* Change the register value according to the skip setting passed
+	 * into this function.
+	 */
+	if (GeneratorChromaSkip)
+		FrameEncodeRegValue |= XVTC_ENC_GACPS_MASK;
+
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_GFENC_OFFSET),
+				FrameEncodeRegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the pixel skip setting used by the Generator in the VTC
+* core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	GeneratorChromaSkipPtr will point to the value indicating
+*		whether one pixel is skipped between active chroma for the
+*		Generator module after this function returns. Value 1 means
+*		that 1 pixel is skipped and zero means that no pixels are
+*		skipped.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetSkipPixel(XVtc *InstancePtr, int *GeneratorChromaSkipPtr)
+{
+	u32 FrameEncodeRegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(GeneratorChromaSkipPtr != NULL);
+
+	/* Read Control register value back */
+	FrameEncodeRegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						(XVTC_GFENC_OFFSET));
+
+	/* Populate the skip variable values according to the skip setting
+	 * used by the core.
+	 */
+	if (FrameEncodeRegValue & XVTC_ENC_GACPS_MASK)
+		*GeneratorChromaSkipPtr = 1;
+	else
+		*GeneratorChromaSkipPtr = 0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the Generator delay setting of the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param 	VertDelay indicates the number of total lines per frame to
+*		delay the generator output. The valid range is from 0 to 4095.
+* @param	HoriDelay indicates the number of total clock cycles per line
+*		to delay the generator output. The valid range is from 0 to
+*		4095.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetDelay(XVtc *InstancePtr, int VertDelay, int HoriDelay)
+{
+	u32 RegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(VertDelay >= 0);
+	Xil_AssertVoid(HoriDelay >= 0);
+	Xil_AssertVoid(VertDelay <= 4095);
+	Xil_AssertVoid(HoriDelay <= 4095);
+
+	/* Calculate the delay value */
+	RegValue = HoriDelay & XVTC_GGD_HDELAY_MASK;
+	RegValue |= (VertDelay << XVTC_GGD_VDELAY_SHIFT) &
+			XVTC_GGD_VDELAY_MASK;
+
+	/* Update the Generator Global Delay register w/ the value */
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, (XVTC_GGD_OFFSET),
+			RegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the Generator delay setting used by the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	VertDelayPtr will point to a value indicating the number of
+*		total lines per frame to delay the generator output after
+*		this function returns.
+* @param	HoriDelayPtr will point to a value indicating the number of
+*		total clock cycles per line to delay the generator output
+*		after this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetDelay(XVtc *InstancePtr, int *VertDelayPtr, int *HoriDelayPtr)
+{
+	u32 RegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(VertDelayPtr != NULL);
+	Xil_AssertVoid(HoriDelayPtr != NULL);
+
+	/* Read the Generator Global Delay register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+				(XVTC_GGD_OFFSET));
+
+	/* Calculate the delay values */
+	*HoriDelayPtr = RegValue & XVTC_GGD_HDELAY_MASK;
+	*VertDelayPtr = (RegValue & XVTC_GGD_VDELAY_MASK) >>
+				XVTC_GGD_VDELAY_SHIFT;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the SYNC setting of a frame sync used by the VTC
+* core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	FrameSyncIndex indicates the index number of the frame sync.
+*		The valid range is from 0 to 15.
+* @param	VertStart indicates the vertical line count during which the
+*		frame sync is active. The valid range is from 0 to 4095.
+* @param	HoriStart indicates the horizontal cycle count during which the
+*		frame sync is active. The valid range is from 0 to 4095.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetFSync(XVtc *InstancePtr, u16 FrameSyncIndex, u16 VertStart,
+			u16 HoriStart)
+{
+	u32 RegValue;
+	u32 RegAddress;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(FrameSyncIndex <= 15);
+	Xil_AssertVoid(VertStart <= 4095);
+	Xil_AssertVoid(HoriStart <= 4095);
+
+	/* Calculate the sync value */
+	RegValue = HoriStart & XVTC_FSXX_HSTART_MASK;
+	RegValue |= (VertStart << XVTC_FSXX_VSTART_SHIFT) &
+			XVTC_FSXX_VSTART_MASK;
+
+	/* Calculate the frame sync register address to write to */
+	RegAddress = XVTC_FS00_OFFSET + FrameSyncIndex * XVTC_REG_ADDRGAP;
+
+	/* Update the Generator Global Delay register w/ the value */
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, RegAddress, RegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the SYNC setting of a frame sync used by the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	FrameSyncIndex indicates the index number of the frame sync.
+* 		The valid range is from 0 to 15.
+* @param	VertStartPtr will point to the value that indicates the
+* 		vertical line count during which the frame sync is active once
+*		this function returns.
+* @param	HoriStartPtr will point to the value that indicates the
+*		horizontal cycle count during which the frame sync is active
+*		once this function returns.
+*
+* @return	None.
+*
+******************************************************************************/
+void XVtc_GetFSync(XVtc *InstancePtr, u16 FrameSyncIndex,
+			u16 *VertStartPtr, u16 *HoriStartPtr)
+{
+	u32 RegValue;
+	u32 RegAddress;
+
+	/* Assert bad arguments and conditions */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(FrameSyncIndex <= 15);
+	Xil_AssertVoid(VertStartPtr != NULL);
+	Xil_AssertVoid(VertStartPtr != NULL);
+
+	/* Calculate the frame sync register address to read from */
+	RegAddress = XVTC_FS00_OFFSET + FrameSyncIndex * XVTC_REG_ADDRGAP;
+
+	/* Read the frame sync register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, RegAddress);
+
+	/* Calculate the frame sync values */
+	*HoriStartPtr = RegValue & XVTC_FSXX_HSTART_MASK;
+	*VertStartPtr = (RegValue & XVTC_FSXX_VSTART_MASK) >>
+				XVTC_FSXX_VSTART_SHIFT;
+}
+
+/*****************************************************************************/
+/**
+ * This function sets the VBlank/VSync Horizontal Offsets for the Generator
+ * in a VTC device.
+ *
+ * @param  InstancePtr is a pointer to the VTC device instance to be worked on.
+ * @param  HoriOffsets points to a VBlank/VSync Horizontal Offset configuration
+ *	   with the setting to use on the VTC device.
+ * @return NONE.
+ *
+ *****************************************************************************/
+void XVtc_SetGeneratorHoriOffset(XVtc *InstancePtr,
+				XVtc_HoriOffsets *HoriOffsets)
+{
+	u32 RegValue;
+
+	/* Assert bad arguments and conditions */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(HoriOffsets != NULL);
+
+	/* Calculate and update Generator VBlank Hori. Offset 0 register value
+	 */
+	RegValue = (HoriOffsets->V0BlankHoriStart) & XVTC_XVXHOX_HSTART_MASK;
+	RegValue |= (HoriOffsets->V0BlankHoriEnd << XVTC_XVXHOX_HEND_SHIFT) &
+					XVTC_XVXHOX_HEND_MASK;
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, XVTC_GVBHOFF_OFFSET,
+								RegValue);
+
+	/* Calculate and update Generator VSync Hori. Offset 0 register
+	 * value
+	 */
+	RegValue = (HoriOffsets->V0SyncHoriStart) & XVTC_XVXHOX_HSTART_MASK;
+	RegValue |= (HoriOffsets->V0SyncHoriEnd << XVTC_XVXHOX_HEND_SHIFT) &
+					XVTC_XVXHOX_HEND_MASK;
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, XVTC_GVSHOFF_OFFSET,
+								RegValue);
+
+	/* Calculate and update Generator VBlank Hori. Offset 1 register
+	 * value
+	 */
+	RegValue = (HoriOffsets->V1BlankHoriStart) & XVTC_XVXHOX_HSTART_MASK;
+	RegValue |= (HoriOffsets->V1BlankHoriEnd << XVTC_XVXHOX_HEND_SHIFT) &
+					XVTC_XVXHOX_HEND_MASK;
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress, XVTC_GVBHOFF_F1_OFFSET,
+								RegValue);
+
+	/* Calculate and update Generator VSync Hori. Offset 1 register
+	 * value
+	 */
+	RegValue = (HoriOffsets->V1SyncHoriStart) & XVTC_XVXHOX_HSTART_MASK;
+	RegValue |= (HoriOffsets->V1SyncHoriEnd << XVTC_XVXHOX_HEND_SHIFT) &
+					XVTC_XVXHOX_HEND_MASK;
+	XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GVSHOFF_F1_OFFSET,
+								RegValue);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the VBlank/VSync Horizontal Offsets currently used by
+* the Generator in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	HoriOffsets points to a VBlank/VSync Horizontal Offset
+*		configuration structure that will be populated with the setting
+*		currently used on the Generator in the given VTC device after
+*		this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetGeneratorHoriOffset(XVtc *InstancePtr,
+					XVtc_HoriOffsets *HoriOffsets)
+{
+	u32 RegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(HoriOffsets != NULL);
+
+	/* Parse Generator VBlank Hori. Offset 0 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GVBHOFF_OFFSET);
+	HoriOffsets->V0BlankHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V0BlankHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+
+	/* Parse Generator VSync Hori. Offset 0 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_GVSHOFF_OFFSET);
+	HoriOffsets->V0SyncHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V0SyncHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+
+	/* Parse Generator VBlank Hori. Offset 1 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_GVBHOFF_F1_OFFSET);
+	HoriOffsets->V1BlankHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V1BlankHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+
+	/* Parse Generator VSync Hori. Offset 1 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+					 XVTC_GVSHOFF_F1_OFFSET);
+	HoriOffsets->V1SyncHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V1SyncHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the VBlank/VSync Horizontal Offsets detected by
+* the Detector in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	HoriOffsets points to a VBlank/VSync Horizontal Offset
+*		configuration structure that will be populated with the setting
+*		detected on the Detector in the given VTC device after this
+*		function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetDetectorHoriOffset(XVtc *InstancePtr,
+				XVtc_HoriOffsets *HoriOffsets)
+{
+	u32 RegValue;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(HoriOffsets != NULL);
+
+	/* Parse Detector VBlank Hori. Offset 0 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DVBHOFF_OFFSET);
+	HoriOffsets->V0BlankHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V0BlankHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+
+	/* Parse Detector VSync Hori. Offset 0 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_DVSHOFF_OFFSET);
+	HoriOffsets->V0SyncHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V0SyncHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+
+	/* Parse Detector VBlank Hori. Offset 1 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_DVBHOFF_F1_OFFSET);
+	HoriOffsets->V1BlankHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V1BlankHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+
+	/* Parse Detector VSync Hori. Offset 1 register value */
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_DVSHOFF_F1_OFFSET);
+	HoriOffsets->V1SyncHoriStart = RegValue & XVTC_XVXHOX_HSTART_MASK;
+	HoriOffsets->V1SyncHoriEnd = (RegValue & XVTC_XVXHOX_HEND_MASK)
+					>> XVTC_XVXHOX_HEND_SHIFT;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up VTC signal to be used by the Generator module
+* in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	SignalCfgPtr is a pointer to the VTC signal configuration
+*		to be used by the Generator module in the VTC core.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+void XVtc_SetGenerator(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr)
+{
+	u32 RegValue;
+	u32 r_htotal, r_vtotal, r_hactive, r_vactive;
+	XVtc_Signal *SCPtr;
+	XVtc_HoriOffsets horiOffsets;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(SignalCfgPtr != NULL);
+
+	SCPtr = SignalCfgPtr;
+	if(SCPtr->OriginMode == 0)
+	{
+		r_htotal = SCPtr->HTotal+1;
+		r_vtotal = SCPtr->V0Total+1;
+
+		r_hactive = r_htotal - SCPtr->HActiveStart;
+		r_vactive = r_vtotal - SCPtr->V0ActiveStart;
+
+		RegValue = (r_htotal) & XVTC_SB_START_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GHSIZE_OFFSET, RegValue);
+
+		RegValue = (r_vtotal) & XVTC_VSIZE_F0_MASK;
+		RegValue |= ((SCPtr->V1Total+1) << XVTC_VSIZE_F1_SHIFT) &
+							XVTC_VSIZE_F1_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GVSIZE_OFFSET, RegValue);
+
+
+		RegValue = (r_hactive) & XVTC_ASIZE_HORI_MASK;
+		RegValue |= ((r_vactive) << XVTC_ASIZE_VERT_SHIFT ) &
+							XVTC_ASIZE_VERT_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GASIZE_OFFSET, RegValue);
+		/* For some resolutions, the FIELD1 vactive size is different
+		 * from FIELD0, e.g. XVIDC_VM_720x486_60_I (SDI NTSC),
+		 * As there is no vactive FIELD1 entry in the video common
+		 * library, program it separately. For resolutions where
+		 * vactive values are different, it should be taken care in
+		 * corrosponding driver. Otherwise program same values in
+		 * FIELD0 and FIELD1 registers */
+		RegValue = ((r_vactive) << XVTC_ASIZE_VERT_SHIFT) &
+				XVTC_ASIZE_VERT_MASK;
+
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GASIZE_F1_OFFSET, RegValue);
+
+		/* Update the Generator Horizontal 1 Register */
+		RegValue = (SCPtr->HSyncStart + r_hactive) &
+						XVTC_SB_START_MASK;
+		RegValue |= ((SCPtr->HBackPorchStart + r_hactive) <<
+				XVTC_SB_END_SHIFT) & XVTC_SB_END_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GHSYNC_OFFSET, RegValue);
+
+		/* Update the Generator Vertical 1 Register (field 0) */
+		RegValue = (SCPtr->V0SyncStart + r_vactive -1) &
+						XVTC_SB_START_MASK;
+		RegValue |= ((SCPtr->V0BackPorchStart + r_vactive -1) <<
+				XVTC_SB_END_SHIFT) & XVTC_SB_END_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GVSYNC_OFFSET, RegValue);
+
+		/* Update the Generator Vertical Sync Register (field 1) */
+		RegValue = (SCPtr->V1SyncStart + r_vactive -1) &
+						XVTC_SB_START_MASK;
+		RegValue |= ((SCPtr->V1BackPorchStart + r_vactive -1) <<
+					XVTC_SB_END_SHIFT) & XVTC_SB_END_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GVSYNC_F1_OFFSET, RegValue);
+
+		/* Chroma Start */
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GFENC_OFFSET);
+		RegValue &= ~XVTC_ENC_CPARITY_MASK;
+		RegValue = (((SCPtr->V0ChromaStart - SCPtr->V0ActiveStart) <<
+						XVTC_ENC_CPARITY_SHIFT) &
+					XVTC_ENC_CPARITY_MASK) | RegValue;
+
+		RegValue &= ~XVTC_ENC_PROG_MASK;
+		RegValue |= (SCPtr->Interlaced << XVTC_ENC_PROG_SHIFT) &
+				XVTC_ENC_PROG_MASK;
+
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GFENC_OFFSET, RegValue);
+
+		/* Setup default Horizontal Offsets - can override later with
+		 * XVtc_SetGeneratorHoriOffset()
+		 */
+		horiOffsets.V0BlankHoriStart = r_hactive;
+		horiOffsets.V0BlankHoriEnd = r_hactive;
+		horiOffsets.V0SyncHoriStart = SCPtr->HSyncStart + r_hactive;
+		horiOffsets.V0SyncHoriEnd = SCPtr->HSyncStart + r_hactive;
+
+		horiOffsets.V1BlankHoriStart = r_hactive;
+		horiOffsets.V1BlankHoriEnd = r_hactive;
+		horiOffsets.V1SyncHoriStart = SCPtr->HSyncStart + r_hactive;
+		horiOffsets.V1SyncHoriEnd = SCPtr->HSyncStart + r_hactive;
+
+	}
+	else
+	{
+		/* Total in mode=1 is the line width */
+		r_htotal = SCPtr->HTotal;
+		/* Total in mode=1 is the frame height */
+		r_vtotal = SCPtr->V0Total;
+		r_hactive = SCPtr->HFrontPorchStart;
+		r_vactive = SCPtr->V0FrontPorchStart;
+
+		RegValue = (r_htotal) & XVTC_SB_START_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GHSIZE_OFFSET, RegValue);
+
+		RegValue = (r_vtotal) & XVTC_VSIZE_F0_MASK;
+		RegValue |= ((SCPtr->V1Total) << XVTC_VSIZE_F1_SHIFT) &
+							XVTC_VSIZE_F1_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GVSIZE_OFFSET, RegValue);
+
+
+		RegValue = (r_hactive) & XVTC_ASIZE_HORI_MASK;
+		RegValue |= ((r_vactive) << XVTC_ASIZE_VERT_SHIFT) &
+							XVTC_ASIZE_VERT_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GASIZE_OFFSET, RegValue);
+		/* For some resolutions, the FIELD1 vactive size is different
+		 * from FIELD0, e.g. XVIDC_VM_720x486_60_I (SDI NTSC),
+		 * As there is no vactive FIELD1 entry in the video common
+		 * library, program it separately. For resolutions where
+		 * vactive values are different, it should be taken care in
+		 * corrosponding driver. Otherwise program same values in
+		 * FIELD0 and FIELD1 registers */
+		RegValue = ((r_vactive) << XVTC_ASIZE_VERT_SHIFT) &
+				XVTC_ASIZE_VERT_MASK;
+
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GASIZE_F1_OFFSET, RegValue);
+
+		/* Update the Generator Horizontal 1 Register */
+		RegValue = (SCPtr->HSyncStart) & XVTC_SB_START_MASK;
+		RegValue |= ((SCPtr->HBackPorchStart) << XVTC_SB_END_SHIFT) &
+						XVTC_SB_END_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GHSYNC_OFFSET, RegValue);
+
+
+		/* Update the Generator Vertical Sync Register (field 0) */
+		RegValue = (SCPtr->V0SyncStart) & XVTC_SB_START_MASK;
+		RegValue |= ((SCPtr->V0BackPorchStart) << XVTC_SB_END_SHIFT) &
+						XVTC_SB_END_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+						XVTC_GVSYNC_OFFSET, RegValue);
+
+		/* Update the Generator Vertical Sync Register (field 1) */
+		RegValue = (SCPtr->V1SyncStart) & XVTC_SB_START_MASK;
+		RegValue |= ((SCPtr->V1BackPorchStart) << XVTC_SB_END_SHIFT) &
+						XVTC_SB_END_MASK;
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GVSYNC_F1_OFFSET, RegValue);
+
+		/* Chroma Start */
+		  RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GFENC_OFFSET);
+		RegValue &= ~XVTC_ENC_CPARITY_MASK;
+		RegValue = (((SCPtr->V0ChromaStart - SCPtr->V0ActiveStart) <<
+							XVTC_ENC_CPARITY_SHIFT)
+					& XVTC_ENC_CPARITY_MASK) | RegValue;
+
+		RegValue &= ~XVTC_ENC_PROG_MASK;
+		RegValue |= (SCPtr->Interlaced << XVTC_ENC_PROG_SHIFT) &
+						XVTC_ENC_PROG_MASK;
+
+		XVtc_WriteReg(InstancePtr->Config.BaseAddress,
+					XVTC_GFENC_OFFSET, RegValue);
+
+		/* Setup default Horizontal Offsets - can override later with
+		 * XVtc_SetGeneratorHoriOffset()
+		 */
+		horiOffsets.V0BlankHoriStart = r_hactive;
+		horiOffsets.V0BlankHoriEnd = r_hactive;
+		horiOffsets.V0SyncHoriStart = SCPtr->HSyncStart;
+		horiOffsets.V0SyncHoriEnd = SCPtr->HSyncStart;
+		horiOffsets.V1BlankHoriStart = r_hactive;
+		horiOffsets.V1BlankHoriEnd = r_hactive;
+		horiOffsets.V1SyncHoriStart = SCPtr->HSyncStart;
+		horiOffsets.V1SyncHoriEnd = SCPtr->HSyncStart;
+
+	}
+	XVtc_SetGeneratorHoriOffset(InstancePtr, &horiOffsets);
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the VTC signal setting used by the Generator module
+* in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	SignalCfgPtr is a pointer to a VTC signal configuration
+*		which will be populated with the setting used by the Generator
+*		module in the VTC core once this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetGenerator(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr)
+{
+	u32 RegValue;
+  u32 r_htotal, r_vtotal, r_hactive, r_vactive;
+	XVtc_Signal *SCPtr;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(SignalCfgPtr != NULL);
+
+	SCPtr = SignalCfgPtr;
+  if(SCPtr->OriginMode == 0)
+  {
+
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GHSIZE_OFFSET);
+	r_htotal = (RegValue) & XVTC_SB_START_MASK;
+	SCPtr->HTotal = (r_htotal-1) & XVTC_SB_START_MASK;
+
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GVSIZE_OFFSET);
+	r_vtotal = (RegValue) & XVTC_VSIZE_F0_MASK;
+	SCPtr->V0Total = (r_vtotal-1) & XVTC_VSIZE_F0_MASK;
+	SCPtr->V1Total = (RegValue & XVTC_VSIZE_F1_MASK) >> XVTC_VSIZE_F1_SHIFT;
+    if(SCPtr->V1Total != 0)
+    {
+      SCPtr->V1Total = SCPtr->V1Total - 1;
+    }
+
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GASIZE_OFFSET);
+	r_hactive = (RegValue) & XVTC_ASIZE_HORI_MASK;
+	SCPtr->HActiveStart = (r_htotal - r_hactive) & XVTC_ASIZE_HORI_MASK;
+	r_vactive = (RegValue & XVTC_ASIZE_VERT_MASK) >> XVTC_ASIZE_VERT_SHIFT;
+
+	SCPtr->V0ActiveStart = (r_vtotal - r_vactive) & XVTC_VSIZE_F0_MASK;
+	SCPtr->V1ActiveStart = (SCPtr->V1Total - r_vactive - 1) & XVTC_VSIZE_F0_MASK;
+
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GHSYNC_OFFSET);
+    SCPtr->HSyncStart = ((RegValue - r_hactive) & XVTC_SB_START_MASK);
+    SCPtr->HBackPorchStart = (((RegValue>>16) - r_hactive) & XVTC_SB_START_MASK);
+
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GVSYNC_OFFSET);
+    SCPtr->V0SyncStart = ((RegValue-r_vactive+1) & XVTC_SB_START_MASK);
+    SCPtr->V0BackPorchStart = (((RegValue>>16) - r_vactive+1) & XVTC_SB_START_MASK);
+
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GVSYNC_F1_OFFSET);
+    SCPtr->V1SyncStart = ((RegValue-r_vactive+1) & XVTC_SB_START_MASK);
+    SCPtr->V1BackPorchStart = (((RegValue>>16) - r_vactive+1) & XVTC_SB_START_MASK);
+
+
+	/* Get signal values from the Generator Vertical 2 Register (field 0)*/
+	RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress, XVTC_GFENC_OFFSET);
+	SCPtr->V0ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+					XVTC_ENC_CPARITY_SHIFT) + (r_vtotal - r_vactive)) & XVTC_SB_START_MASK;
+
+	SCPtr->V1ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+					XVTC_ENC_CPARITY_SHIFT) + (SCPtr->V1Total - r_vactive - 1)) & XVTC_SB_START_MASK;
+
+	SCPtr->Interlaced = (RegValue & XVTC_ENC_PROG_MASK) >> XVTC_ENC_PROG_SHIFT;
+    SCPtr->HFrontPorchStart = 0;
+    SCPtr->V0FrontPorchStart = 0;
+  }
+	else
+	{
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GHSIZE_OFFSET);
+		r_htotal = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->HTotal = (r_htotal) & XVTC_SB_START_MASK;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GVSIZE_OFFSET);
+		r_vtotal = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->V0Total = (r_vtotal) & XVTC_SB_START_MASK;
+		SCPtr->V1Total = (RegValue>>XVTC_SB_END_SHIFT) &
+							XVTC_SB_START_MASK;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GASIZE_OFFSET);
+		r_hactive = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->HFrontPorchStart = (r_hactive) & XVTC_SB_START_MASK;
+		r_vactive = (RegValue>>XVTC_SB_END_SHIFT) & XVTC_SB_START_MASK;
+		SCPtr->V0FrontPorchStart = (r_vactive) & XVTC_SB_START_MASK;
+		SCPtr->V1FrontPorchStart = SCPtr->V0FrontPorchStart;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GHSYNC_OFFSET);
+		SCPtr->HSyncStart = ((RegValue) & XVTC_SB_START_MASK);
+		SCPtr->HBackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT)) &
+							XVTC_SB_START_MASK);
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GVSYNC_OFFSET);
+		SCPtr->V0SyncStart = ((RegValue) & XVTC_SB_START_MASK);
+		SCPtr->V0BackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT)) &
+							XVTC_SB_START_MASK);
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GVSYNC_F1_OFFSET);
+		SCPtr->V1SyncStart = ((RegValue) & XVTC_SB_START_MASK);
+		SCPtr->V1BackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT)) &
+							XVTC_SB_START_MASK);
+
+		/* Get signal values from the Generator Vertical 2 Register (field 0)*/
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_GFENC_OFFSET);
+		SCPtr->V0ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+				XVTC_ENC_CPARITY_SHIFT)) & XVTC_SB_START_MASK;
+		SCPtr->V1ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+				XVTC_ENC_CPARITY_SHIFT)) & XVTC_SB_START_MASK;
+		SCPtr->Interlaced = (RegValue & XVTC_ENC_PROG_MASK) >> XVTC_ENC_PROG_SHIFT;
+
+		SCPtr->HActiveStart = 0;
+		SCPtr->V0ActiveStart = 0;
+		SCPtr->V1ActiveStart = 0;
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the VTC signal setting used by the Detector module
+* in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	SignalCfgPtr is a pointer to a VTC signal configuration
+*		which will be populated with the setting used by the Detector
+*		module in the VTC core once this function returns.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetDetector(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr)
+{
+	u32 RegValue;
+	u32 r_htotal, r_vtotal, r_hactive, r_vactive;
+	XVtc_Signal *SCPtr;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(SignalCfgPtr != NULL);
+
+	SCPtr = SignalCfgPtr;
+
+	if(SCPtr->OriginMode == 0)
+	{
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_DHSIZE_OFFSET);
+		r_htotal = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->HTotal = (r_htotal-1) & XVTC_SB_START_MASK;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_DVSIZE_OFFSET);
+		r_vtotal = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->V0Total = (r_vtotal-1) & XVTC_SB_START_MASK;
+		SCPtr->V1Total = (RegValue>>XVTC_SB_END_SHIFT) &
+							XVTC_SB_START_MASK;
+		if(SCPtr->V1Total != 0) {
+			SCPtr->V1Total = SCPtr->V1Total - 1;
+		}
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DASIZE_OFFSET);
+		r_hactive = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->HActiveStart = (r_htotal - r_hactive) &
+						XVTC_SB_START_MASK;
+		r_vactive = (RegValue>>XVTC_SB_END_SHIFT) &
+						XVTC_SB_START_MASK;
+		SCPtr->V0ActiveStart = (r_vtotal - r_vactive) &
+						XVTC_SB_START_MASK;
+		SCPtr->V1ActiveStart = (SCPtr->V1Total - r_vactive - 1) &
+							XVTC_SB_START_MASK;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DHSYNC_OFFSET);
+		SCPtr->HSyncStart = ((RegValue - r_hactive) &
+						XVTC_SB_START_MASK);
+		SCPtr->HBackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT) -
+							r_hactive)
+						& XVTC_SB_START_MASK);
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DVSYNC_OFFSET);
+		SCPtr->V0SyncStart = ((RegValue-r_vactive+1) &
+							XVTC_SB_START_MASK);
+		SCPtr->V0BackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT) -
+					r_vactive+1) & XVTC_SB_START_MASK);
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+						XVTC_GVSYNC_F1_OFFSET);
+		SCPtr->V1SyncStart = ((RegValue-r_vactive+1) &
+						XVTC_SB_START_MASK);
+		SCPtr->V1BackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT) -
+								r_vactive+1)
+							& XVTC_SB_START_MASK);
+
+		/* Get signal values from the Generator Vertical 2 Register
+		 * (field 0)
+		 */
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DFENC_OFFSET);
+		SCPtr->V0ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+					XVTC_ENC_CPARITY_SHIFT) +
+				(r_vtotal - r_vactive)) & XVTC_SB_START_MASK;
+
+		SCPtr->V1ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+						XVTC_ENC_CPARITY_SHIFT) +
+			(SCPtr->V1Total - r_vactive - 1)) & XVTC_SB_START_MASK;
+		SCPtr->Interlaced = (RegValue & XVTC_ENC_PROG_MASK) >> XVTC_ENC_PROG_SHIFT;
+
+		SCPtr->HFrontPorchStart = 0;
+		SCPtr->V0FrontPorchStart = 0;
+	}
+	else
+	{
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DHSIZE_OFFSET);
+		r_htotal = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->HTotal = (r_htotal) & XVTC_SB_START_MASK;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DVSIZE_OFFSET);
+		r_vtotal = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->V0Total = (r_vtotal) & XVTC_SB_START_MASK;
+		SCPtr->V1Total = (RegValue>>XVTC_SB_END_SHIFT) &
+							XVTC_SB_START_MASK;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DASIZE_OFFSET);
+		r_hactive = (RegValue) & XVTC_SB_START_MASK;
+		SCPtr->HFrontPorchStart = (r_hactive) & XVTC_SB_START_MASK;
+		r_vactive = (RegValue>>XVTC_SB_END_SHIFT) & XVTC_SB_START_MASK;
+		SCPtr->V0FrontPorchStart = (r_vactive) & XVTC_SB_START_MASK;
+		SCPtr->V1FrontPorchStart = SCPtr->V0FrontPorchStart;
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DHSYNC_OFFSET);
+		SCPtr->HSyncStart = ((RegValue) & XVTC_SB_START_MASK);
+		SCPtr->HBackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT)) &
+							XVTC_SB_START_MASK);
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DVSYNC_OFFSET);
+		SCPtr->V0SyncStart = ((RegValue) & XVTC_SB_START_MASK);
+		SCPtr->V0BackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT)) &
+							XVTC_SB_START_MASK);
+
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DVSYNC_F1_OFFSET);
+		SCPtr->V1SyncStart = ((RegValue) & XVTC_SB_START_MASK);
+		SCPtr->V1BackPorchStart = (((RegValue>>XVTC_SB_END_SHIFT)) &
+							XVTC_SB_START_MASK);
+
+
+		/* Get signal values from the Generator Vertical 2 Register
+		 * (field 0)
+		 */
+		RegValue = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+							XVTC_DFENC_OFFSET);
+		SCPtr->V0ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+				XVTC_ENC_CPARITY_SHIFT)) & XVTC_SB_START_MASK;
+
+		SCPtr->V1ChromaStart = (((RegValue & XVTC_ENC_CPARITY_MASK) >>
+				XVTC_ENC_CPARITY_SHIFT)) & XVTC_SB_START_MASK;
+		SCPtr->Interlaced = (RegValue & XVTC_ENC_PROG_MASK) >> XVTC_ENC_PROG_SHIFT;
+
+		SCPtr->HActiveStart = 0;
+		SCPtr->V0ActiveStart = 0;
+		SCPtr->V1ActiveStart = 0;
+	}
+
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function facilitates software identification of exact version of the
+* VTC hardware (h/w).
+*
+* @param	InstancePtr is a pointer to the XVtc instance.
+*
+* @return	Version, contents of a Version register.
+*
+* @note		None.
+*
+******************************************************************************/
+u32 XVtc_GetVersion(XVtc *InstancePtr)
+{
+	u32 Version;
+
+	/* Verify argument */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+
+	/* Read Version register */
+	Version = XVtc_ReadReg(InstancePtr->Config.BaseAddress,
+				XVTC_VER_OFFSET);
+
+	return Version;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts the video mode integer into the video timing
+* information stored within the XVtc_Timing pointer.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	Mode is a u16 int defined as macro to one of the predefined
+*		Video Modes.
+* @param	TimingPtr is a pointer to a VTC Video Timing Structure.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_ConvVideoMode2Timing(XVtc *InstancePtr, u16 Mode,
+					XVtc_Timing *TimingPtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(TimingPtr != NULL);
+
+	/* clear timing structure. Set Interlaced to 0 by default */
+	memset((void *)TimingPtr, 0, sizeof(XVtc_Timing));
+
+	switch(Mode)
+	{
+	case XVTC_VMODE_720P: // 720p@60 (1280x720 HD 720)
+	{
+
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1280;
+		TimingPtr->HFrontPorch   = 110;
+		TimingPtr->HSyncWidth    = 40;
+		TimingPtr->HBackPorch    = 220;
+		TimingPtr->HSyncPolarity = 1;
+
+		// Vertical Timing
+		TimingPtr->VActiveVideo  = 720;
+		TimingPtr->V0FrontPorch   = 5;
+		TimingPtr->V0SyncWidth    = 5;
+		TimingPtr->V0BackPorch    = 20;
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+	case XVTC_VMODE_1080P: // 1080p@60 (1920x1080 HD 1080)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1920;
+		TimingPtr->HFrontPorch   = 88;
+		TimingPtr->HSyncWidth    = 44;
+		TimingPtr->HBackPorch    = 148;
+		TimingPtr->HSyncPolarity = 1;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 1080;
+		TimingPtr->V0FrontPorch   = 4;
+		TimingPtr->V0SyncWidth    = 5;
+		TimingPtr->V0BackPorch    = 36;
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+	case XVTC_VMODE_480P: // 480p@60
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 720;
+		TimingPtr->HFrontPorch   = 16;
+		TimingPtr->HSyncWidth    = 62;
+		TimingPtr->HBackPorch    = 60;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 480;
+		TimingPtr->V0FrontPorch   = 9;
+		TimingPtr->V0SyncWidth    = 6;
+		TimingPtr->V0BackPorch    = 30;
+		TimingPtr->VSyncPolarity = 0;
+
+		break;
+	}
+	case XVTC_VMODE_576P: // 576p@50
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 720;
+		TimingPtr->HFrontPorch   = 12;
+		TimingPtr->HSyncWidth    = 64;
+		TimingPtr->HBackPorch    = 68;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 576;
+		TimingPtr->V0FrontPorch   = 5;
+		TimingPtr->V0SyncWidth    = 5;
+		TimingPtr->V0BackPorch    = 39;
+		TimingPtr->VSyncPolarity = 0;
+
+		break;
+	}
+	case XVTC_VMODE_VGA: // 640x480 (VGA)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 640;
+		TimingPtr->HFrontPorch   = 16;
+		TimingPtr->HSyncWidth    = 96;
+		TimingPtr->HBackPorch    = 48;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 480;
+		TimingPtr->V0FrontPorch   = 10;
+		TimingPtr->V0SyncWidth    = 2;
+		TimingPtr->V0BackPorch    = 33;
+		TimingPtr->VSyncPolarity = 0;
+
+		break;
+	}
+	case XVTC_VMODE_SVGA: // 800x600@60 (SVGA)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 800;
+		TimingPtr->HFrontPorch   = 40;
+		TimingPtr->HSyncWidth    = 128;
+		TimingPtr->HBackPorch    = 88;
+		TimingPtr->HSyncPolarity = 1;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 600;
+		TimingPtr->V0FrontPorch   = 1;
+		TimingPtr->V0SyncWidth    = 4;
+		TimingPtr->V0BackPorch    = 23;
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+	case XVTC_VMODE_XGA: // 1024x768@60 (XGA)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1024;
+		TimingPtr->HFrontPorch   = 24;
+		TimingPtr->HSyncWidth    = 136;
+		TimingPtr->HBackPorch    = 160;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 768;
+		TimingPtr->V0FrontPorch   = 3;
+		TimingPtr->V0SyncWidth    = 6;
+		TimingPtr->V0BackPorch    = 29;
+		TimingPtr->VSyncPolarity = 0;
+
+		break;
+	}
+	case XVTC_VMODE_SXGA: // 1280x1024@60 (SXGA)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1280;
+		TimingPtr->HFrontPorch   = 48;
+		TimingPtr->HSyncWidth    = 112;
+		TimingPtr->HBackPorch    = 248;
+		TimingPtr->HSyncPolarity = 1;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 1024;
+		TimingPtr->V0FrontPorch   = 1;
+		TimingPtr->V0SyncWidth    = 3;
+		TimingPtr->V0BackPorch    = 38;
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+
+	case XVTC_VMODE_WXGAPLUS: // 1440x900@60 (WXGA+)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1440;
+		TimingPtr->HFrontPorch   = 80;
+		TimingPtr->HSyncWidth    = 152;
+		TimingPtr->HBackPorch    = 232;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 900;
+		TimingPtr->V0FrontPorch   = 3;
+		TimingPtr->V0SyncWidth    = 6;
+		TimingPtr->V0BackPorch    = 25;
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+	case XVTC_VMODE_WSXGAPLUS: // 1680x1050@60 (WSXGA+)
+	{
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1680;
+		TimingPtr->HFrontPorch   = 104;
+		TimingPtr->HSyncWidth    = 176;
+		TimingPtr->HBackPorch    = 280;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 1050;
+		TimingPtr->V0FrontPorch   = 3;
+		TimingPtr->V0SyncWidth    = 6;
+		TimingPtr->V0BackPorch    = 30;
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+	case XVTC_VMODE_1080I: // 1080i@60
+	{
+		TimingPtr->Interlaced = 1;
+
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 1920;
+		TimingPtr->HFrontPorch   = 88;
+		TimingPtr->HSyncWidth    = 44;
+		TimingPtr->HBackPorch    = 148;
+		TimingPtr->HSyncPolarity = 1;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 540;
+		TimingPtr->V0FrontPorch   = 2;
+		TimingPtr->V0SyncWidth    = 5;
+		TimingPtr->V0BackPorch    = 15;
+
+		TimingPtr->V1FrontPorch   = 2;
+		TimingPtr->V1SyncWidth    = 5;
+		TimingPtr->V1BackPorch    = 16;
+
+		TimingPtr->VSyncPolarity = 1;
+
+		break;
+	}
+	case XVTC_VMODE_NTSC: //480i@60
+	{
+		TimingPtr->Interlaced = 1;
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 720;
+		TimingPtr->HFrontPorch   = 19;
+		TimingPtr->HSyncWidth    = 62;
+		TimingPtr->HBackPorch    = 57;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 240;
+		TimingPtr->V0FrontPorch   = 4;
+		TimingPtr->V0SyncWidth    = 3;
+		TimingPtr->V0BackPorch    = 15;
+
+		TimingPtr->V1FrontPorch   = 4;
+		TimingPtr->V1SyncWidth    = 3;
+		TimingPtr->V1BackPorch    = 16;
+
+		TimingPtr->VSyncPolarity = 0;
+
+		break;
+	}
+	case XVTC_VMODE_PAL: //576i@50
+	{
+		TimingPtr->Interlaced = 1;
+		// Horizontal Timing
+		TimingPtr->HActiveVideo  = 720;
+		TimingPtr->HFrontPorch   = 12;
+		TimingPtr->HSyncWidth    = 63;
+		TimingPtr->HBackPorch    = 69;
+		TimingPtr->HSyncPolarity = 0;
+
+		 // Vertical Timing
+		TimingPtr->VActiveVideo  = 288;
+		TimingPtr->V0FrontPorch   = 2;
+		TimingPtr->V0SyncWidth    = 3;
+		TimingPtr->V0BackPorch    = 19;
+
+		TimingPtr->V1FrontPorch   = 2;
+		TimingPtr->V1SyncWidth    = 3;
+		TimingPtr->V1BackPorch    = 20;
+
+		TimingPtr->VSyncPolarity = 0;
+
+		break;
+	}
+
+	// add other video formats here
+	}
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts the video timing structure into the VTC signal
+* configuration structure, horizontal offsets structure and the
+* polarity structure.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	TimingPtr is a pointer to a Video Timing structure to be read.
+* @param	SignalCfgPtr is a pointer to a VTC signal configuration to be
+*		set.
+* @param	HOffPtr is a pointer to a VTC horizontal offsets structure to
+*		be set.
+* @param	PolarityPtr is a pointer to a VTC polarity structure to be set.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_ConvTiming2Signal(XVtc *InstancePtr, XVtc_Timing *TimingPtr,
+			XVtc_Signal *SignalCfgPtr, XVtc_HoriOffsets *HOffPtr,
+			XVtc_Polarity *PolarityPtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(TimingPtr != NULL);
+	Xil_AssertVoid(SignalCfgPtr != NULL);
+	Xil_AssertVoid(HOffPtr != NULL);
+	Xil_AssertVoid(PolarityPtr != NULL);
+
+
+	/* Setting up VTC Polarity.  */
+	memset((void *)PolarityPtr, 0, sizeof(XVtc_Polarity));
+	PolarityPtr->ActiveChromaPol = 1;
+	PolarityPtr->ActiveVideoPol  = 1;
+	PolarityPtr->FieldIdPol      = 1;
+	/* Vblank matches Vsync Polarity */
+	PolarityPtr->VBlankPol       = TimingPtr->VSyncPolarity;
+	PolarityPtr->VSyncPol        = TimingPtr->VSyncPolarity;
+	/* hblank matches hsync Polarity */
+	PolarityPtr->HBlankPol       = TimingPtr->HSyncPolarity;
+	PolarityPtr->HSyncPol        = TimingPtr->HSyncPolarity;
+
+
+	memset((void *)SignalCfgPtr, 0, sizeof(XVtc_Signal));
+	memset((void *)HOffPtr, 0, sizeof(XVtc_HoriOffsets));
+
+	/* Populate the VTC Signal config structure. */
+	/* Active Video starts at 0 */
+	SignalCfgPtr->OriginMode = 1;
+	SignalCfgPtr->HActiveStart      = 0;
+	SignalCfgPtr->HFrontPorchStart  = TimingPtr->HActiveVideo;
+	SignalCfgPtr->HSyncStart        = SignalCfgPtr->HFrontPorchStart +
+							TimingPtr->HFrontPorch;
+	SignalCfgPtr->HBackPorchStart   = SignalCfgPtr->HSyncStart +
+							TimingPtr->HSyncWidth;
+	SignalCfgPtr->HTotal            = SignalCfgPtr->HBackPorchStart +
+							TimingPtr->HBackPorch;
+
+	SignalCfgPtr->V0ChromaStart     = 0;
+	SignalCfgPtr->V0ActiveStart     = 0;
+	SignalCfgPtr->V0FrontPorchStart = TimingPtr->VActiveVideo;
+	SignalCfgPtr->V0SyncStart       = SignalCfgPtr->V0FrontPorchStart +
+						TimingPtr->V0FrontPorch - 1;
+	SignalCfgPtr->V0BackPorchStart  = SignalCfgPtr->V0SyncStart +
+						TimingPtr->V0SyncWidth;
+	SignalCfgPtr->V0Total           = SignalCfgPtr->V0BackPorchStart +
+						TimingPtr->V0BackPorch + 1;
+
+	HOffPtr->V0BlankHoriStart = SignalCfgPtr->HFrontPorchStart;
+	HOffPtr->V0BlankHoriEnd   = SignalCfgPtr->HFrontPorchStart;
+	HOffPtr->V0SyncHoriStart  = SignalCfgPtr->HSyncStart;
+	HOffPtr->V0SyncHoriEnd    = SignalCfgPtr->HSyncStart;
+
+	if(TimingPtr->Interlaced == 1) {
+		SignalCfgPtr->V1ChromaStart     = 0;
+		SignalCfgPtr->V1ActiveStart     = 0;
+		SignalCfgPtr->V1FrontPorchStart = TimingPtr->VActiveVideo;
+		SignalCfgPtr->V1SyncStart       =
+					SignalCfgPtr->V1FrontPorchStart +
+					TimingPtr->V1FrontPorch - 1;
+		SignalCfgPtr->V1BackPorchStart  =
+						SignalCfgPtr->V1SyncStart +
+							TimingPtr->V1SyncWidth;
+		SignalCfgPtr->V1Total           =
+					SignalCfgPtr->V1BackPorchStart +
+						TimingPtr->V1BackPorch + 1;
+		SignalCfgPtr->Interlaced 		= 1;
+
+		/* Align to H blank */
+		HOffPtr->V1BlankHoriStart = SignalCfgPtr->HFrontPorchStart;
+		/* Align to H Blank */
+		HOffPtr->V1BlankHoriEnd   = SignalCfgPtr->HFrontPorchStart;
+
+		/* Align to half line */
+		HOffPtr->V1SyncHoriStart  = SignalCfgPtr->HSyncStart -
+						(SignalCfgPtr->HTotal / 2);
+		HOffPtr->V1SyncHoriEnd    = SignalCfgPtr->HSyncStart -
+						(SignalCfgPtr->HTotal / 2);
+	}
+	/* Progressive formats */
+	else {
+	/* Set Field 1 same as Field 0 */
+		SignalCfgPtr->V1ChromaStart     = SignalCfgPtr->V0ChromaStart;
+		SignalCfgPtr->V1ActiveStart     = SignalCfgPtr->V0ActiveStart;
+		SignalCfgPtr->V1FrontPorchStart =
+					SignalCfgPtr->V0FrontPorchStart;
+		SignalCfgPtr->V1SyncStart       = SignalCfgPtr->V0SyncStart;
+		SignalCfgPtr->V1BackPorchStart  =
+					SignalCfgPtr->V0BackPorchStart;
+		SignalCfgPtr->V1Total           = SignalCfgPtr->V0Total;
+		SignalCfgPtr->Interlaced		= 0;
+
+		HOffPtr->V1BlankHoriStart = HOffPtr->V0BlankHoriStart;
+		HOffPtr->V1BlankHoriEnd   = HOffPtr->V0BlankHoriEnd;
+		HOffPtr->V1SyncHoriStart  = HOffPtr->V0SyncHoriStart;
+		HOffPtr->V1SyncHoriEnd    = HOffPtr->V0SyncHoriEnd;
+	}
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts the VTC signal structure, horizontal offsets
+* structure and the polarity structure into the Video Timing structure.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	SignalCfgPtr is a pointer to a VTC signal configuration to
+*		be read
+* @param	HOffPtr is a pointer to a VTC horizontal offsets structure
+*		to be read
+* @param	PolarityPtr is a pointer to a VTC polarity structure to be
+*		read.
+* @param	TimingPtr is a pointer to a Video Timing structure to be set.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_ConvSignal2Timing(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr,
+				XVtc_HoriOffsets *HOffPtr,
+				XVtc_Polarity *PolarityPtr,
+				XVtc_Timing *TimingPtr)
+{
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(SignalCfgPtr != NULL);
+	Xil_AssertVoid(HOffPtr != NULL);
+	Xil_AssertVoid(PolarityPtr != NULL);
+	Xil_AssertVoid(TimingPtr != NULL);
+	Xil_AssertVoid(SignalCfgPtr->OriginMode == 1);
+
+	memset((void *)TimingPtr, 0, sizeof(XVtc_Timing));
+
+	/* Set Polarity */
+	TimingPtr->VSyncPolarity = PolarityPtr->VSyncPol;
+	TimingPtr->HSyncPolarity = PolarityPtr->HSyncPol;
+
+	/* Horizontal Timing */
+	TimingPtr->HActiveVideo = SignalCfgPtr->HFrontPorchStart;
+
+
+	TimingPtr->HFrontPorch  = SignalCfgPtr->HSyncStart -
+					SignalCfgPtr->HFrontPorchStart;
+	TimingPtr->HSyncWidth   = SignalCfgPtr->HBackPorchStart -
+				        SignalCfgPtr->HSyncStart;
+	TimingPtr->HBackPorch   = SignalCfgPtr->HTotal -
+					SignalCfgPtr->HBackPorchStart;
+
+	/* Vertical Timing */
+	TimingPtr->VActiveVideo  = SignalCfgPtr->V0FrontPorchStart;
+
+
+	TimingPtr->V0FrontPorch  = SignalCfgPtr->V0SyncStart -
+					  SignalCfgPtr->V0FrontPorchStart + 1;
+	TimingPtr->V0SyncWidth   = SignalCfgPtr->V0BackPorchStart -
+						SignalCfgPtr->V0SyncStart + 1;
+	TimingPtr->V0BackPorch   = SignalCfgPtr->V0Total -
+					SignalCfgPtr->V0BackPorchStart;
+
+	TimingPtr->V1FrontPorch  = SignalCfgPtr->V1SyncStart -
+					SignalCfgPtr->V1FrontPorchStart + 1;
+	TimingPtr->V1SyncWidth   = SignalCfgPtr->V1BackPorchStart -
+						SignalCfgPtr->V1SyncStart + 1;
+	TimingPtr->V1BackPorch   = SignalCfgPtr->V1Total -
+					SignalCfgPtr->V1BackPorchStart;
+
+	/* Interlaced */
+	TimingPtr->Interlaced  = SignalCfgPtr->Interlaced;
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function converts the video timing structure into predefined video
+* mode values returned as a short integer.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	TimingPtr is a pointer to a Video Timing structure to be read.
+*
+* @return	VideoMode is the video mode of the VTC core.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVtc_ConvTiming2VideoMode(XVtc *InstancePtr, XVtc_Timing *TimingPtr)
+{
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertNonvoid(TimingPtr != NULL);
+
+	/* Checking for Interlaced value */
+	if(TimingPtr->Interlaced == 0) {
+		if(TimingPtr->HActiveVideo == 1280) {
+			if (TimingPtr->VActiveVideo == 720) {
+				return XVTC_VMODE_720P;
+			}
+			else if (TimingPtr->VActiveVideo == 1024) {
+				return XVTC_VMODE_SXGA;
+			}
+
+		}
+		else if((TimingPtr->HActiveVideo == 1920) &&
+				(TimingPtr->VActiveVideo == 1080)) {
+			return XVTC_VMODE_1080P;
+		}
+		else if(TimingPtr->HActiveVideo == 720) {
+			if (TimingPtr->VActiveVideo == 480) {
+				return XVTC_VMODE_480P;
+			}
+			else if (TimingPtr->VActiveVideo == 576) {
+				return XVTC_VMODE_576P;
+			}
+		}
+		else if((TimingPtr->HActiveVideo == 640) &&
+				(TimingPtr->VActiveVideo == 480)) {
+			return XVTC_VMODE_VGA;
+		}
+		else if((TimingPtr->HActiveVideo == 800) &&
+				(TimingPtr->VActiveVideo == 600)) {
+			return XVTC_VMODE_SVGA;
+		}
+		else if((TimingPtr->HActiveVideo == 1024) &&
+			(TimingPtr->VActiveVideo == 768)) {
+			return XVTC_VMODE_XGA;
+		}
+		else if((TimingPtr->HActiveVideo == 1440) &&
+				(TimingPtr->VActiveVideo == 900)) {
+			return XVTC_VMODE_WXGAPLUS;
+		}
+		else if((TimingPtr->HActiveVideo == 1680) &&
+				(TimingPtr->VActiveVideo == 1050)) {
+			return XVTC_VMODE_WSXGAPLUS;
+		}
+
+	}
+	/* Interlaced */
+	else {
+		if((TimingPtr->HActiveVideo == 720) &&
+			(TimingPtr->VActiveVideo == 240)) {
+			return XVTC_VMODE_NTSC;
+		}
+		else if((TimingPtr->HActiveVideo == 1920) &&
+			(TimingPtr->VActiveVideo == 540)) {
+			return XVTC_VMODE_1080I;
+		}
+		else if((TimingPtr->HActiveVideo == 720) &&
+				(TimingPtr->VActiveVideo == 288)) {
+			return XVTC_VMODE_PAL;
+		}
+
+	}
+
+	/* Not found - read from Timing to discover format */
+	return 0;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the generator (Polarity, H/V values and horizontal
+* offsets) by reading the configuration from a video timing structure.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	TimingPtr is a pointer to a Video Timing Structure to be read.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetGeneratorTiming(XVtc *InstancePtr, XVtc_Timing * TimingPtr)
+{
+	XVtc_Polarity Polarity;
+	XVtc_Signal Signal;
+	XVtc_HoriOffsets Hoff;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(TimingPtr != NULL);
+
+	XVtc_ConvTiming2Signal(InstancePtr, TimingPtr, &Signal, &Hoff,
+				&Polarity);
+	XVtc_SetPolarity(InstancePtr, &Polarity);
+	XVtc_SetGenerator(InstancePtr, &Signal);
+	XVtc_SetGeneratorHoriOffset(InstancePtr, &Hoff);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function sets up the generator (Polarity, H/V values and horizontal
+* offsets) by reading the configuration from a video mode short integer.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	Mode is a short integer predefined video mode.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_SetGeneratorVideoMode(XVtc *InstancePtr, u16 Mode)
+{
+	XVtc_Timing Timing;
+
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	XVtc_ConvVideoMode2Timing(InstancePtr, Mode, &Timing);
+
+	XVtc_SetGeneratorTiming(InstancePtr, &Timing);
+
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the video timing structure settings currently used by
+* generator in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	TimingPtr is a pointer to a Video Timing Structure to be set.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetGeneratorTiming(XVtc *InstancePtr, XVtc_Timing *TimingPtr)
+{
+
+	XVtc_Polarity Polarity;
+	XVtc_Signal Signal;
+	XVtc_HoriOffsets Hoff;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(TimingPtr != NULL);
+
+
+	Signal.OriginMode = 1;
+	XVtc_GetPolarity(InstancePtr, &Polarity);
+	XVtc_GetGeneratorHoriOffset(InstancePtr, &Hoff);
+	XVtc_GetGenerator(InstancePtr, &Signal);
+
+	XVtc_ConvSignal2Timing(InstancePtr, &Signal, &Hoff, &Polarity,
+					TimingPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the video mode currently used by the generator
+* in the VTC core. If the video mode is unknown or not recognized, then 0
+* will be returned.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	VideoMode is the video mode of the VTC core.
+*
+* @note		Note.
+*
+******************************************************************************/
+u16 XVtc_GetGeneratorVideoMode(XVtc *InstancePtr)
+{
+
+	u16 mode;
+	XVtc_Timing Timing;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	XVtc_GetGeneratorTiming(InstancePtr, &Timing);
+	mode = XVtc_ConvTiming2VideoMode(InstancePtr, &Timing);
+
+	return mode;
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the video timing structure settings currently reported by
+* the detector in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+* @param	TimingPtr is a pointer to a Video Timing structure to be set.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_GetDetectorTiming(XVtc *InstancePtr, XVtc_Timing *TimingPtr)
+{
+	XVtc_Polarity Polarity;
+	XVtc_Signal Signal;
+	XVtc_HoriOffsets Hoff;
+
+	/* Verify arguments */
+	Xil_AssertVoid(InstancePtr != NULL);
+	Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+	Xil_AssertVoid(TimingPtr != NULL);
+
+
+	Signal.OriginMode = 1;
+	XVtc_GetDetector(InstancePtr, &Signal);
+	XVtc_GetDetectorPolarity(InstancePtr, &Polarity);
+	XVtc_GetDetectorHoriOffset(InstancePtr, &Hoff);
+
+	XVtc_ConvSignal2Timing(InstancePtr, &Signal, &Hoff, &Polarity,
+					TimingPtr);
+}
+
+/*****************************************************************************/
+/**
+*
+* This function gets the video mode currently reported by the detector
+* in the VTC core. If the video mode is unknown or not recognized, then 0
+* will be returned.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return 	VideoMode is the video mode of the VTC core.
+*
+* @note		None.
+*
+******************************************************************************/
+u16 XVtc_GetDetectorVideoMode(XVtc *InstancePtr)
+{
+	u16 mode;
+	XVtc_Timing Timing;
+
+	/* Verify arguments */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+
+	XVtc_GetDetectorTiming(InstancePtr, &Timing);
+	mode = XVtc_ConvTiming2VideoMode(InstancePtr, &Timing);
+
+	return mode;
+}
+
+/*****************************************************************************/
+/**
+*
+* This routine is a stub for the asynchronous callbacks. The stub is here in
+* case the upper layer forgot to set the handlers. On initialization, all
+* handlers except error handler are set to this callback. It is considered an
+* error for this handler to be invoked.
+*
+* @param	CallBackRef is a callback reference passed in by the upper
+*		layer when setting the callback functions, and passed back
+*		to the upper layer when the callback is invoked.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void StubCallBack(void *CallBackRef, u32 Mask)
+{
+	(void)CallBackRef;
+	(void)Mask;
+	Xil_AssertVoidAlways();
+}
+
+/*****************************************************************************/
+/**
+*
+* This routine is a stub for the asynchronous error interrupt callback. The
+* stub is here in case the upper layer forgot to set the handler. On
+* initialization, Error interrupt handler is set to this callback. It is
+* considered an error for this handler to be invoked.
+*
+* @param	CallBackRef is a callback reference passed in by the upper
+*		layer when setting the callback functions, and passed back to
+*		the upper layer when the callback is invoked.
+* @param 	ErrorMask is a bit mask indicating the cause of the error. Its
+*		value equals 'OR'ing one or more XVTC_IXR_*_MASK values defined
+*		in xvtc_hw.h.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+static void StubErrCallBack(void *CallBackRef, u32 ErrorMask)
+{
+	(void)CallBackRef;
+	(void)ErrorMask;
+	Xil_AssertVoidAlways();
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc.h
@@ -0,0 +1,949 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xvtc.h
+* @{
+* @details
+*
+* This is the main header file of Xilinx MVI Video Timing Controller (VTC)
+* device driver. The VTC device detects video signals, independently
+* overrides any one of them, re-generates video signals with +/- delay and
+* with polarity inversion, and generates up to 16 one cycle Frame Sync outputs.
+*
+* The device has the following main features:
+* - Detect video signals:
+*	- horizontal sync
+*	- horizontal blank
+*	- vertical sync
+*	- vertical blank
+*	- active video
+*	- field id
+* - Independently override any one signal.
+* - Re-generate video signals with +/- delay and with polarity inversion.
+* - Generate up to 16 one cycle Frame Sync outputs.
+*
+* For a full description of VTC features, please see the hardware
+* specification.
+*
+* <b>Software Initialization & Configuration</b>
+*
+* The application needs to do following steps in order for preparing the
+* VTC to be ready to process video signal handling.
+*
+* - Call XVtc_LookupConfig using a device ID to find the core
+*   configuration.
+* - Call XVtc_CfgInitialize to initialize the device and the driver
+*   instance associated with it.
+* - Call XVtc_SetGenerator to set up the video signals to generate,
+*   if desired.
+* - Call XVtc_SetPolarity to set up the video signal polarity.
+* - Call XVtc_SetSource for source selection
+* - Call XVtc_SetGeneratorHoriOffset to set up the Generator
+*   VBlank/VSync horizontal offsets, if values other than the default are
+*   needed
+* - Call XVtc_EnableSync, if generator needs to be synced to the detector
+* - Call XVtc_Enable to enable/start the VTC device.
+*
+* <b>Interrupts </b>
+*
+* The interrupt types supported are:
+* - Frame Sync Interrupts 0 - 15
+* - Generator interrupt:
+*	- Generator Active Video Interrupt
+*	- Generator VBLANK Interrupt
+* - Detector interrupt:
+*	- Detector Active Video Interrupt
+*	- Detector VBLANK Interrupt
+* - Signal Lock interrupt:
+*	- Active Chroma signal lock
+*	- Active Video Signal Lock
+*	- Field ID Signal Lock
+*	- Vertical Blank Signal Lock
+*	- Vertical Sync Signal Lock
+*	- Horizontal Blank Signal Lock
+*	- Horizontal Sync Signal Lock
+*
+* <b> Virtual Memory </b>
+*
+* This driver supports Virtual Memory. The RTOS is responsible for calculating
+* the correct device base address in Virtual Memory space.
+*
+* <b> Threads </b>
+*
+* This driver is not thread safe. Any needs for threads or thread mutual
+* exclusion must be satisfied by the layer above this driver.
+*
+* <b> Asserts </b>
+*
+* Asserts are used within all Xilinx drivers to enforce constraints on argument
+* values. Asserts can be turned off on a system-wide basis by defining, at
+* compile time, the NDEBUG identifier. By default, asserts are turned on and it
+* is recommended that users leave asserts on during development.
+*
+* <b> Building the driver </b>
+*
+* The Vtc driver is composed of several source files. This allows the user
+* to build and link only those parts of the driver that are necessary.
+*
+* <b> Examples </b>
+*
+* An example is provided with this driver to demonstrate the driver usage.
+*
+* <b>Cache Coherency</b>
+*
+* <b>Alignment</b>
+*
+* <b>Limitations</b>
+*
+* <b>BUS Interface</b>
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- -----------------------------------------------
+* 1.00a xd     08/05/08 First release
+* 1.01a xd     07/23/10 Added GIER Added more h/w generic info into
+*                       xparameters.h Feed callbacks with pending
+*                       interrupt info. Added Doxygen & Version support
+* 2.00a xd     05/13/11 1. Renamed to "Video Timing Controller"
+*                       2. Added Generator/Detector VBlank/VSync
+*                          Horizontal offset setup/fetch support
+*                       3. Renamed the IP to support to be axi_vtc
+*                       4. Supported sync between generator and detector
+*                          with addition of new XVtc_EnableSync and
+*                          XVtc_DisableSync functions
+*                       5. Renamed XVtc_SetSync to XVtc_SetFSync
+*                       6. Renamed XVtc_GetSync to XVtc_GetFSync
+*                       7. Removed unnecessary register write in
+*                          XVtc_Reset
+*                       8. Corrected driver name in .mdd file
+*                       9. Updated register bit definition (a few fields grow
+*                          from 12 to 13 bit wide)
+* 2.00a cm     05/25/11 1. Renamed XVtc_SetSkip to XVtc_SetSkipLine
+*                       2. Renamed XVtc_GetSkip to XVtc_GetSkipLine
+*                       3. Added XVtc_SetSkipPixel
+*                       4. Added XVtc_GetSkipPixel
+* 2.00a cm     06/16/12 1. Added missing xil_assert.h include
+* 2.00a cm     07/25/12 1. Removed unused XVtc_IntrSetLockPolarity function
+* 3.00a cm     08/02/12 1. Added the XVtc_Sync_Reset frame sync'ed SW
+*                       reset function.
+* 3.00a cjm    08/02/12 Converted from xio.h to xil_io.h, translating
+*                       basic types, MB cache functions, exceptions and
+*                       assertions to xil_io format.
+*                       Replaced the following
+*                       "XExc_Init" -> "Xil_ExceptionInit"
+*                       "XExc_RegisterHandler" -> "Xil_ExceptionRegister
+*                                                                 Handler"
+*                       "XEXC_ID_NON_CRITICAL_INT" -> "XIL_EXCEPTION_ID_INT"
+*                       "XExceptionHandler" -> "Xil_ExceptionHandler"
+*                       "XExc_mEnableExceptions" -> "Xil_ExceptionEnable"
+*                       "XEXC_NON_CRITICAL" -> "XIL_EXCEPTION_NON_CRITICAL"
+*                       "XExc_DisableExceptions" -> "Xil_ExceptionDisable"
+*                       "XExc_RemoveHandler" -> "Xil_ExceptionRemoveHandler"
+*                       "microblaze_enable_interrupts" -> "Xil_ExceptionEnable"
+*                       "microblaze_disable_interrupts" -> "Xil_Exception
+*                                                               Disable"
+*
+*                       "XCOMPONENT_IS_STARTED" -> "XIL_COMPONENT_IS_STARTED"
+*                       "XCOMPONENT_IS_READY" -> "XIL_COMPONENT_IS_READY"
+*
+*                       "XASSERT_NONVOID" -> "Xil_AssertNonvoid"
+*                       "XASSERT_VOID_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XASSERT_VOID" -> "Xil_AssertVoid"
+*                       "Xil_AssertVoid_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XAssertStatus" -> "Xil_AssertStatus"
+*                       "XAssertSetCallback" -> "Xil_AssertCallback"
+*
+*                       "XASSERT_OCCURRED" -> "XIL_ASSERT_OCCURRED"
+*                       "XASSERT_NONE" -> "XIL_ASSERT_NONE"
+*
+*                       "microblaze_disable_dcache" -> "Xil_DCacheDisable"
+*                       "microblaze_enable_dcache" -> "Xil_DCacheEnable"
+*                       "microblaze_enable_icache" -> "Xil_ICacheEnable"
+*                       "microblaze_disable_icache" -> "Xil_ICacheDisable"
+*                       "microblaze_init_dcache_range" -> "Xil_DCacheInvalidate
+*                                                                       Range"
+*
+*                       "XCache_DisableDCache" -> "Xil_DCacheDisable"
+*                       "XCache_DisableICache" -> "Xil_ICacheDisable"
+*                       "XCache_EnableDCache" -> "Xil_DCacheEnableRegion"
+*                       "XCache_EnableICache" -> "Xil_ICacheEnableRegion"
+*                       "XCache_InvalidateDCacheLine" -> "Xil_DCacheInvalidate
+*                                                                       Range"
+*
+*                       "XUtil_MemoryTest32" -> "Xil_TestMem32"
+*                       "XUtil_MemoryTest16" -> "Xil_TestMem16"
+*                       "XUtil_MemoryTest8" -> "Xil_TestMem8"
+*
+*                       "xutil.h" -> "xil_testmem.h"
+*
+*                       "xbasic_types.h" -> "xil_types.h"
+*                       "xio.h" -> "xil_io.h"
+*
+*                       "XIo_In32" -> "Xil_In32"
+*                       "XIo_Out32" -> "Xil_Out32"
+*
+*                       "XTRUE" -> "TRUE"
+*                       "XFALSE" -> "FALSE"
+*                       "XNULL" -> "NULL"
+*
+*                       "Xuint8" -> "u8"
+*                       "Xuint16" -> "u16"
+*                       "Xuint32" -> "u32"
+*                       "Xint8" -> "char"
+*                       "Xint16" -> "short"
+*                       "Xint32" -> "long"
+*                       "Xfloat32" -> "float"
+*                       "Xfloat64" -> "double"
+*                       "Xboolean" -> "int"
+*                       "XTEST_FAILED" -> "XST_FAILURE"
+*                       "XTEST_PASSED" -> "XST_SUCCESS"
+* 4.00a cjm    02/07/13 Removed Unused Functions
+*                       XVtc_IntrEnableGlobal
+*                       XVtc_IntrDisableGlobal
+* 5.00a cjm    08/07/13 Replaced XVTC_RESET with (XVTC_CTL)
+*                       Replaced XVTC_RESET_RESET_MASK with
+*                       (XVTC_CTL_RESET_MASK)
+*                       Replaced XVTC_SYNC_RESET_MASK with (XVTC_CTL_SRST_MASK)
+* 5.00a cjm    10/30/13 Replaced XVtc_RegUpdate with XVtc_RegUpdateEnable
+*                       Added XVtc_RegUpdateDisable
+*                       Removed type parameter from XVtc_Enable
+*                       Added XVtc_EnableGenerator to enable only the Generator
+*                       Added XVtc_EnableDetector to enable only the Detector
+* 5.00a cjm    11/01/13 Added Timing, VideoMode and Signal Conversion
+*                       Functions:
+*                       XVtc_ConvVideoMode2Timing
+*                       XVtc_ConvTiming2Signal
+*                       XVtc_ConvSignal2Timing
+*                       XVtc_ConvTiming2VideoMode
+*                       Added Timing and Video Mode Set/Get Functions:
+*                       XVtc_SetGeneratorTiming
+*                       XVtc_SetGeneratorVideoMode
+*                       XVtc_GetGeneratorTiming
+*                       XVtc_GetGeneratorVideoMode
+*                       XVtc_GetDetectorTiming
+*                       XVtc_GetDetectorVideoMode
+* 6.0   adk    19/12/13 Updated as per the New Tcl API's.
+* 6.1   adk    23/08/14 Implemented XVtc_SelfTest in
+*                       xvtc_selftest.c.
+*                       Modified prototype of XVtc_GetVersion API.
+* 7.0   vns    02/25/15 Added Interlaced field to XVtc_Signal structure,
+*                       Removed XVtc_RegUpdate as there are is one more API,
+*                       XVtc_RegUpdateEnable with same functionality but
+*                       provided backward compatability.
+*
+*                       Modifications from xvtc.c file are:
+*                       Modified HActiveVideo value to 1920 for
+*                       XVTC_VMODE_1080I mode.
+*                       Removed Major, Minor and Revision parameters from
+*                       XVtc_GetVersion.
+*                       Modified return type of XVtc_GetVersion from
+*                       void to u32.
+*                       Added progressive and interlaced mode switching feature.
+*                       Modified XVtc_SetGenerator, XVtc_GetGenerator,
+*                       XVtc_GetDetector, XVtc_ConvTiming2Signal and
+*                       XVtc_ConvSignal2Timing APIs
+*
+*                       Modifications from xvtc_hw.h file are:
+*                       Removed XVTC_ERR_FIL_MASK macro because it is  not
+*                       present in latest product guide.
+*                       Modified register offsets from XVTC_* to XVTC_*_OFFSET
+*                       for consistency.
+*                       Added backward compatibility macros.
+*
+*                       Modifications from xvtc_intr.c and xvtc_sinit.c files
+*                       are:
+*                       updated doxygen tags.
+*
+*                       Modifications from xvtc_selftest.c file are:
+*                       First Release.
+*                       Implemented following function:
+*                       XVtc_SelfTest.
+* 7.1   vns    10/14/15 Added InterlacedMode feild to XVtc_SourceSelect
+*                       structure
+* 7.2   sk     08/16/16 Used UINTPTR instead of u32 for Baseaddress as part of
+*                       adding 64 bit support. CR# 867425.
+*                       Changed the prototype of XVtc_CfgInitialize API.
+*       ms     03/17/17 Added readme.txt file in examples folder for doxygen
+*                       generation.
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XVTC_H_
+#define XVTC_H_		/**< Prevent circular inclusions
+			  * by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xvtc_hw.h"
+#include "xil_assert.h"
+#include "xstatus.h"
+
+/************************** Constant Definitions *****************************/
+
+/** @name Interrupt Types for setting up Callbacks
+* @{
+*/
+#define XVTC_HANDLER_FRAMESYNC	1	/**< A frame sync event
+					  * interrupt type */
+#define XVTC_HANDLER_LOCK	2	/**< A signal lock event
+					  *  interrupt type */
+#define XVTC_HANDLER_DETECTOR	3	/**< A detector event
+					  *  interrupt type */
+#define XVTC_HANDLER_GENERATOR	4	/**< A generator event
+					  *  interrupt type */
+#define XVTC_HANDLER_ERROR	5	/**< An error condition
+					  *  interrupt type */
+/*@}*/
+
+/** @name Options for enabling VTC modules
+ *  @{
+ */
+#define XVTC_EN_GENERATOR	1	/**< To enable generator */
+#define XVTC_EN_DETECTOR	2	/**< To enable detector */
+/*@}*/
+
+/** @name Address gap between two register next to each other
+ *  @{
+ */
+#define XVTC_REG_ADDRGAP	4	/**< Register address gap */
+
+
+#define XVTC_VMODE_720P		1	/**< Video mode 720P */
+#define XVTC_VMODE_1080P	2	/**< Video mode 1080P */
+#define XVTC_VMODE_480P		3	/**< Video mode 480P */
+#define XVTC_VMODE_576P		4	/**< Video mode 576P */
+#define XVTC_VMODE_VGA		5	/**< Video mode VGA */
+#define XVTC_VMODE_SVGA		6	/**< Video mode SVGA */
+#define XVTC_VMODE_XGA		7	/**< Video mode XGA */
+#define XVTC_VMODE_SXGA		8	/**< Video mode SXGA */
+#define XVTC_VMODE_WXGAPLUS	9	/**< Video mode WXGAPlus */
+#define XVTC_VMODE_WSXGAPLUS	10	/**< Video mode WSXGAPlus */
+#define XVTC_VMODE_1080I	100	/**< Video mode 1080I */
+#define XVTC_VMODE_NTSC		101	/**< Video mode NTSC */
+#define XVTC_VMODE_PAL		102	/**< Video mode PAL */
+/*@}*/
+
+/**************************** Type Definitions *******************************/
+
+/**
+ * This typedef contains configuration information for a VTC core.
+ * Each VTC device should have a configuration structure associated
+ */
+typedef struct {
+	u16 DeviceId;		/**< DeviceId is the unique ID of the VTC
+				  *  core */
+	UINTPTR BaseAddress;	/**< BaseAddress is the physical base address
+				  *  of the core's registers */
+} XVtc_Config;
+
+/**
+ * This typedef contains Polarity configuration information for a VTC core.
+ */
+typedef struct {
+	u8 ActiveChromaPol;	/**< Active Chroma Output Polarity */
+	u8 ActiveVideoPol;	/**< Active Video Output Polarity */
+	u8 FieldIdPol;		/**< Field ID Output Polarity */
+	u8 VBlankPol;		/**< Vertical Blank Output Polarity */
+	u8 VSyncPol;		/**< Vertical Sync Output Polarity */
+	u8 HBlankPol;		/**< Horizontal Blank Output
+				  *  Polarity */
+	u8 HSyncPol;		/**< Horizontal Sync Output Polarity */
+} XVtc_Polarity;
+
+/**
+ * This typedef contains Source Selection configuration information for a
+ * VTC core.
+ */
+typedef struct {
+	u8 FieldIdPolSrc;	/**< Field ID Output Polarity Source */
+	u8 ActiveChromaPolSrc;	/**< Active Chroma Output Polarity Source */
+	u8 ActiveVideoPolSrc;	/**< Active Video Output Polarity Source */
+	u8 HSyncPolSrc;		/**< Horizontal Sync Output Polarity Source */
+	u8 VSyncPolSrc;		/**< Vertical Sync Output Polarity Source */
+	u8 HBlankPolSrc;	/**< Horizontal Blank Output Polarity Source */
+	u8 VBlankPolSrc;	/**< Vertical Blank Output Polarity Source */
+
+	u8 VChromaSrc;		/**< Start of Active Chroma Register
+				  *  Source Select */
+	u8 VActiveSrc;		/**< Vertical Active Video Start Register
+				  *  Source Select */
+	u8 VBackPorchSrc;	/**< Vertical Back Porch Start Register
+				  *  Source Select */
+	u8 VSyncSrc;		/**< Vertical Sync Start Register Source
+				  *  Select */
+	u8 VFrontPorchSrc;	/**< Vertical Front Porch Start Register Source
+				  *  Select */
+	u8 VTotalSrc;		/**< Vertical Total Register Source Select */
+	u8 HActiveSrc;		/**< Horizontal Active Video Start Register
+				  *  Source Select */
+	u8 HBackPorchSrc;	/**< Horizontal Back Porch Start Register
+				  *  Source Select */
+	u8 HSyncSrc;		/**< Horizontal Sync Start Register
+				  *  Source Select */
+	u8 HFrontPorchSrc;	/**< Horizontal Front Porch Start Register
+				  *  Source Select */
+	u8 HTotalSrc;		/**< Horizontal Total Register Source Select */
+	u8 InterlacedMode;	/**< Interelaced mode */
+
+} XVtc_SourceSelect;
+
+/**
+ * This typedef contains the VTC signal configuration used by the
+ * Generator/Detector modules in a VTC device.
+ */
+typedef struct {
+	u16 OriginMode;		/**< Origin Mode */
+	u16 HTotal;		/**< Horizontal total clock cycles per Line */
+	u16 HFrontPorchStart;	/**< Horizontal Front Porch Start Cycle
+				  *  Count */
+	u16 HSyncStart;		/**< Horizontal Sync Start Cycle Count */
+	u16 HBackPorchStart;	/**< Horizontal Back Porch Start Cycle Count */
+	u16 HActiveStart;	/**< Horizontal Active Video Start Cycle
+				  *  Count */
+
+	u16 V0Total;		/**< Total lines per Frame (Field 0) */
+	u16 V0FrontPorchStart;	/**< Vertical Front Porch Start Line
+				  *  Count * (Field 0) */
+	u16 V0SyncStart;	/**< Vertical Sync Start Line Count
+				  *  (Field 0) */
+	u16 V0BackPorchStart;	/**< Vertical Back Porch Start Line
+				  *  Count *  (Field 0) */
+	u16 V0ActiveStart;	/**< Vertical Active Video Start Line
+				  *  Count *  (Field 0) */
+	u16 V0ChromaStart;	/**< Active Chroma Start Line Count
+				  *  (Field 0) */
+
+	u16 V1Total;		/**< Total lines per Frame (Field 1) */
+	u16 V1FrontPorchStart;	/**< Vertical Front Porch Start Line
+				  *  Count *  (Field 1) */
+	u16 V1SyncStart;	/**< Vertical Sync Start Line Count
+				  *  (Field 1) */
+	u16 V1BackPorchStart;	/**< Vertical Back Porch Start Line Count *
+				  *  (Field 1) */
+	u16 V1ActiveStart;	/**< Vertical Active Video Start Line
+				  *  Count (Field 1) */
+	u16 V1ChromaStart;	/**< Active Chroma Start Line Count
+				  *  (Field 1) */
+	u8 Interlaced;		/**< Interlaced / Progressive video */
+} XVtc_Signal;
+
+/**
+ * This typedef contains Detector/Generator VBlank/VSync Horizontal Offset
+ * configuration information for a VTC device.
+ */
+typedef struct {
+	u16 V0BlankHoriStart;	/**< Vertical Blank Hori Offset Start
+				  *  (field 0) */
+	u16 V0BlankHoriEnd;	/**< Vertical Blank Hori Offset End
+				  *  (field 0) */
+	u16 V0SyncHoriStart;	/**< Vertical Sync  Hori Offset Start
+				  *  (field 0) */
+	u16 V0SyncHoriEnd;	/**< Vertical Sync  Hori Offset End
+				  *  (field 0) */
+	u16 V1BlankHoriStart;	/**< Vertical Blank Hori Offset Start
+				  *  (field 1) */
+	u16 V1BlankHoriEnd;	/**< Vertical Blank Hori Offset End
+				  *  (field 1) */
+	u16 V1SyncHoriStart;	/**< Vertical Sync  Hori Offset Start
+				  * (field 1) */
+	u16 V1SyncHoriEnd;	/**< Vertical Sync  Hori Offset End
+				  *  (field 1) */
+} XVtc_HoriOffsets;
+
+/**
+* This typedef contains Timing (typically in Display Timing) format
+* configuration information for the VTC core.
+*/
+typedef struct {
+	/* Horizontal Timing */
+	u16 HActiveVideo;	/**< Horizontal Active Video Size */
+	u16 HFrontPorch;	/**< Horizontal Front Porch Size */
+	u16 HSyncWidth;		/**< Horizontal Sync Width */
+	u16 HBackPorch;		/**< Horizontal Back Porch Size */
+	u16 HSyncPolarity;	/**< Horizontal Sync Polarity */
+
+	/* Vertical Timing */
+	u16 VActiveVideo;	/**< Vertical Active Video Size */
+	u16 V0FrontPorch;	/**< Vertical Front Porch Size */
+	u16 V0SyncWidth;	/**< Vertical Sync Width */
+	u16 V0BackPorch;	/**< Horizontal Back Porch Size */
+
+	u16 V1FrontPorch;	/**< Vertical Front Porch Size */
+	u16 V1SyncWidth;	/**< Vertical Sync Width */
+	u16 V1BackPorch;	/**< Vertical Back Porch Size */
+
+	u16 VSyncPolarity;	/**< Vertical Sync Polarity */
+
+	u8 Interlaced;		/**< Interlaced / Progressive video */
+} XVtc_Timing;
+
+/**
+*
+* Callback type for all interrupts except error interrupt.
+*
+* @param	CallBackRef is a callback reference passed in by the upper
+*		layer when setting the callback functions, and passed back to
+*		the upper layer when the callback is invoked.
+* @param	Mask is a bit mask indicating the cause of the event. For
+*		current core version, this parameter is "OR" of 0 or more
+*		XVTC_IXR_*_MASK constants defined in xvtc_hw.h.
+*
+* @return	None.
+*
+* @note		None.
+*
+ *****************************************************************************/
+typedef void (*XVtc_CallBack)(void *CallBackRef, u32 Mask);
+
+/**
+*
+* Callback type for Error interrupt.
+*
+* @param	CallBackRef is a callback reference passed in by the upper
+*		layer when setting the callback functions, and passed back to
+*		the upper layer when the callback is invoked.
+* @param	ErrorMask is a bit mask indicating the cause of the error. For
+*		current core version, this parameter always have value 0 and
+*		could be ignored.
+*
+* @return	None.
+*
+* @note		None.
+*
+*****************************************************************************/
+typedef void (*XVtc_ErrorCallBack)(void *CallBackRef, u32 ErrorMask);
+
+/**
+ * The XVtc driver instance data. An instance must be allocated for each
+ * VTC core in use.
+ */
+typedef struct {
+	XVtc_Config Config;	/**< Hardware Configuration */
+	u32 IsReady;		/**< Core and the driver instance are
+				  *  initialized */
+
+	/* Interrupt callbacks*/
+	XVtc_CallBack FrameSyncCallBack;	/**< Callback for Frame Sync
+						  *  interrupt */
+	void *FrameSyncRef;		/**< To be passed to the Frame Sync
+					  *  interrupt callback */
+
+	XVtc_CallBack LockCallBack;	/**< Callback for Signal Lock
+					  *  interrupt */
+	void *LockRef;			/**< To be passed to the Signal Lock
+					  *  interrupt callback */
+
+	XVtc_CallBack DetectorCallBack;	/**< Callback for Detector interrupt */
+	void *DetectorRef;		/**< To be passed to the Detector
+					  *  interrupt callback */
+
+	XVtc_CallBack GeneratorCallBack;	/**< Callback for Generator
+						  *  interrupt */
+	void *GeneratorRef;		/**< To be passed to the Generator
+					  *  interrupt callback */
+
+	XVtc_ErrorCallBack ErrCallBack;	/**< Callback for Error interrupt */
+	void *ErrRef;			/**< To be passed to the Error
+					  *  interrupt callback */
+} XVtc;
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+*
+* This function macro resets the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_Reset(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_Reset(InstancePtr) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_CTL_OFFSET), \
+			(XVTC_CTL_RESET_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This function macro resets the VTC core after the next input frame is
+* complete.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_SyncReset(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_SyncReset(InstancePtr) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_CTL_OFFSET), \
+		(XVTC_CTL_SRST_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This function macro enables synchronization of the Generator with the
+* Detector on the given VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return 	None.
+*
+* @note		C-style signature:
+*		void XVtc_EnableSync(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_EnableSync(InstancePtr) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_CTL_OFFSET), \
+		XVtc_ReadReg((InstancePtr)->Config.BaseAddress, \
+			(XVTC_CTL_OFFSET)) | (XVTC_CTL_SE_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This function macro enables updating timing registers at the end of each
+* Generator frame.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_RegUpdateEnable(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_RegUpdateEnable(InstancePtr) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_CTL_OFFSET), \
+		XVtc_ReadReg((InstancePtr)->Config.BaseAddress, \
+			(XVTC_CTL_OFFSET)) | (XVTC_CTL_RU_MASK))
+
+/*****************************************************************************/
+/**
+*
+* This function macro disables updating timing registers at the end of each
+* Generator frame.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_RegUpdateDisable(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_RegUpdateDisable(InstancePtr) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_CTL_OFFSET), \
+		XVtc_ReadReg((InstancePtr)->Config.BaseAddress, \
+			(XVTC_CTL_OFFSET)) & (~(XVTC_CTL_RU_MASK)))
+
+/*****************************************************************************/
+/**
+*
+* This function macro disables synchronization of the Generator with the
+* Detector on the given VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_DisableSync(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_DisableSync(InstancePtr) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_CTL_OFFSET), \
+		(XVtc_ReadReg((InstancePtr)->Config.BaseAddress, \
+			(XVTC_CTL_OFFSET)) & ~(XVTC_CTL_SE_MASK)))
+
+/*****************************************************************************/
+/**
+*
+* This function macro gets the status of the Detector in the VTC core.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	The Detector status. Use XVTC_DS_* in xvtc_hw.h to interpret
+*		the returned value.
+*
+* @note		C-style signature:
+*		u32 XVtc_GetDetectionStatus(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_GetDetectionStatus(InstancePtr) \
+	XVtc_ReadReg((InstancePtr)->Config.BaseAddress, (XVTC_DTSTAT_OFFSET))
+
+/*****************************************************************************/
+/**
+*
+* This function macro enables individual interrupts of the VTC core by
+* updating the IRQ_ENABLE register.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @param	IntrType is the bit-mask of the interrupts to be enabled.
+*		Bit positions of 1 will be enabled. Bit positions of 0 will
+*		keep the previous setting. This mask is formed by OR'ing
+*		XVTC_IXR_*_MASK bits defined in xvtc_hw.h.
+*
+* @return	None.
+*
+* @note		The existing enabled interrupt(s) will remain enabled.
+*		C-style signature:
+*		void XVtc_IntrEnable(XVtc *InstancePtr, u32 IntrType)
+*
+******************************************************************************/
+#define XVtc_IntrEnable(InstancePtr, IntrType) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_IER_OFFSET), \
+		(((IntrType) & (XVTC_IXR_ALLINTR_MASK)) | \
+			(XVtc_ReadReg((InstancePtr)->Config.BaseAddress, \
+				(XVTC_IER_OFFSET)))))
+
+/*****************************************************************************/
+/**
+*
+* This function macro disables individual interrupts of the VTC core by
+* updating the IRQ_ENABLE register.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @param	IntrType is the bit-mask of the interrupts to be disabled.
+*		Bit positions of 1 will be disabled. Bit positions of 0 will
+*		keep the previous setting. This mask is formed by OR'ing
+*		XVTC_IXR_*_MASK bits defined in xvtc_hw.h.
+*
+* @return	None.
+*
+* @note		Any other interrupt not covered by parameter IntrType,
+*		if enabled before this macro is called, will remain enabled.
+*		C-style signature:
+*		void XVtc_IntrDisable(XVtc *InstancePtr, u32 IntrType)
+*
+******************************************************************************/
+#define XVtc_IntrDisable(InstancePtr, IntrType) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_IER_OFFSET), \
+		XVtc_ReadReg((InstancePtr)->Config.BaseAddress, \
+		(XVTC_IER_OFFSET)) & ((~(IntrType)) & (XVTC_IXR_ALLINTR_MASK)))
+
+/*****************************************************************************/
+/**
+*
+* This function macro returns the pending interrupt status of the VTC core
+* read from the Status register.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	The status of pending interrupts of the VTC core.
+* 		Use XVTC_IXR_*_MASK constants defined in xvtc_hw.h to
+*		interpret this value.
+*
+* @note		C-style signature:
+*		u32 XVtc_StatusGePending(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_StatusGetPending(InstancePtr) \
+	XVtc_ReadReg((InstancePtr)->Config.BaseAddress, (XVTC_ISR_OFFSET)) & \
+		(XVTC_IXR_ALLINTR_MASK)
+
+/*****************************************************************************/
+/**
+*
+* This function macro returns the pending interrupts of the VTC core for
+* the interrupts that have been enabled.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	The pending interrupts of the VTC core. Use
+*		XVTC_IXR_*_MASK constants defined in xvtc_hw.h to
+*		interpret this value. The returned value is a logical AND of
+*		the contents of the STATUS Register and the IRQ_ENABLE
+*		Register.
+*
+* @note		C-style signature:
+*		u32 XVtc_IntrGetPending(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_IntrGetPending(InstancePtr) \
+	(XVtc_ReadReg((InstancePtr)->Config.BaseAddress, XVTC_IER_OFFSET) & \
+	 XVtc_ReadReg((InstancePtr)->Config.BaseAddress, XVTC_ISR_OFFSET) & \
+	 XVTC_IXR_ALLINTR_MASK)
+
+/*****************************************************************************/
+/**
+*
+* This function macro clears/acknowledges pending interrupts of the VTC
+* core in the Status register. Bit positions of 1 will be cleared.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+* @param	IntrType is the pending interrupts to clear/acknowledge.
+*		Use OR'ing of XVTC_IXR_*_MASK constants defined in
+*		xvtc_hw.h to create this parameter value.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_IntrClear(XVtc *InstancePtr, u32 IntrType)
+*
+******************************************************************************/
+#define XVtc_IntrClear(InstancePtr, IntrType) \
+	XVtc_WriteReg((InstancePtr)->Config.BaseAddress, (XVTC_ISR_OFFSET), \
+		((IntrType) & (XVTC_IXR_ALLINTR_MASK)))
+
+/*****************************************************************************/
+/**
+*
+* This function macro resets the VTC core after the next input frame is
+* complete.
+*
+* @param	InstancePtr is a pointer to the VTC core instance to be
+*		worked on.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_Sync_Reset(XVtc *InstancePtr)
+*
+******************************************************************************/
+#define XVtc_Sync_Reset		XVtc_SyncReset
+
+/** @name Compatibility Macros
+ *  @{
+ */
+#define XVtc_RegUpdate		XVtc_RegUpdateEnable
+/*@}*/
+/************************** Function Prototypes ******************************/
+
+/* Initialization and control functions in xvtc.c */
+
+/* Initialization */
+int XVtc_CfgInitialize(XVtc *InstancePtr, XVtc_Config *CfgPtr,
+			UINTPTR EffectiveAddr);
+
+/* Enabling and Disabling the VTC core */
+void XVtc_EnableGenerator(XVtc *InstancePtr);
+void XVtc_EnableDetector(XVtc *InstancePtr);
+void XVtc_Enable(XVtc *InstancePtr);
+void XVtc_DisableGenerator(XVtc *InstancePtr);
+void XVtc_DisableDetector(XVtc *InstancePtr);
+void XVtc_Disable(XVtc *InstancePtr);
+
+/* Video Mode, Timing and Signal/HoriOffsets/Polarity Conversions */
+void XVtc_ConvVideoMode2Timing(XVtc *InstancePtr, u16 Mode,
+		XVtc_Timing *TimingPtr);
+void XVtc_ConvTiming2Signal(XVtc *InstancePtr, XVtc_Timing *TimingPtr,
+		XVtc_Signal *SignalCfgPtr, XVtc_HoriOffsets *HOffPtr,
+		XVtc_Polarity *PolarityPtr);
+void XVtc_ConvSignal2Timing(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr,
+		XVtc_HoriOffsets *HOffPtr, XVtc_Polarity *PolarityPtr,
+		XVtc_Timing *TimingPtr);
+u16 XVtc_ConvTiming2VideoMode(XVtc *InstancePtr, XVtc_Timing *TimingPtr);
+
+/* Timing/Video Mode Setting/Fetching */
+void XVtc_SetGeneratorTiming(XVtc *InstancePtr, XVtc_Timing * TimingPtr);
+void XVtc_SetGeneratorVideoMode(XVtc *InstancePtr, u16 Mode);
+void XVtc_GetGeneratorTiming(XVtc *InstancePtr, XVtc_Timing *TimingPtr);
+u16  XVtc_GetGeneratorVideoMode(XVtc *InstancePtr);
+void XVtc_GetDetectorTiming(XVtc *InstancePtr, XVtc_Timing *TimingPtr);
+u16  XVtc_GetDetectorVideoMode(XVtc *InstancePtr);
+
+/* Polarity setting */
+void XVtc_SetPolarity(XVtc *InstancePtr, XVtc_Polarity *PolarityPtr);
+void XVtc_GetPolarity(XVtc *InstancePtr, XVtc_Polarity *PolarityPtr);
+void XVtc_GetDetectorPolarity(XVtc *InstancePtr, XVtc_Polarity *PolarityPtr);
+
+/* Source selection */
+void XVtc_SetSource(XVtc *InstancePtr, XVtc_SourceSelect *SourcePtr);
+void XVtc_GetSource(XVtc *InstancePtr, XVtc_SourceSelect *SourcePtr);
+
+/* Skipping setting */
+void XVtc_SetSkipLine(XVtc *InstancePtr, int GeneratorChromaSkip);
+void XVtc_GetSkipLine(XVtc *InstancePtr, int *GeneratorChromaSkipPtr);
+void XVtc_SetSkipPixel(XVtc *InstancePtr, int GeneratorChromaSkip);
+void XVtc_GetSkipPixel(XVtc *InstancePtr, int *GeneratorChromaSkipPtr);
+
+/* VTC generator/detector setting/fetching */
+void XVtc_SetGenerator(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr);
+void XVtc_GetGenerator(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr);
+void XVtc_GetDetector(XVtc *InstancePtr, XVtc_Signal *SignalCfgPtr);
+
+/* Delay setting */
+void XVtc_SetDelay(XVtc *InstancePtr, int VertDelay, int HoriDelay);
+void XVtc_GetDelay(XVtc *InstancePtr, int *VertDelayPtr, int *HoriDelayPtr);
+
+/* Frame Sync setting */
+void XVtc_SetFSync(XVtc *InstancePtr, u16 FrameSyncIndex,
+			   u16 VertStart, u16 HoriStart);
+void XVtc_GetFSync(XVtc *InstancePtr, u16 FrameSyncIndex,
+			   u16 *VertStartPtr, u16 *HoriStartPtr);
+
+/* Horizontal Offset Setting */
+void XVtc_SetGeneratorHoriOffset(XVtc *InstancePtr,
+			   XVtc_HoriOffsets *HoriOffset);
+void XVtc_GetGeneratorHoriOffset(XVtc *InstancePtr,
+			   XVtc_HoriOffsets *HoriOffset);
+void XVtc_GetDetectorHoriOffset(XVtc *InstancePtr,
+			   XVtc_HoriOffsets *HoriOffset);
+
+/* Version function */
+u32 XVtc_GetVersion(XVtc *InstancePtr);
+
+/* Initialization functions in xvtc_sinit.c */
+XVtc_Config *XVtc_LookupConfig(u16 DeviceId);
+
+/*
+ * Interrupt related function(s) in xvtc_intr.c
+ */
+void XVtc_IntrHandler(void *InstancePtr);
+int XVtc_SetCallBack(XVtc *InstancePtr, u32 IntrType,
+			void *CallBackFunc, void *CallBackRef);
+
+/* SelfTest related function in xvtc_selftest.c */
+int XVtc_SelfTest(XVtc *InstancePtr);
+
+/************************** Variable Declarations ****************************/
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc_hw.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc_hw.h
@@ -0,0 +1,655 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xvtc_hw.h
+* @{
+*
+* This header file contains identifiers and register-level core functions (or
+* macros) that can be used to access the Xilinx VTC core.
+*
+* For more information about the operation of this core, see the hardware
+* specification and documentation in the higher level driver xvtc.h source
+* code file.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- -------------------------------------------------------
+* 1.00a xd     08/05/08 First release.
+* 1.01a xd     07/23/10 Added GIER. Added more h/w generic info into
+*                       xparameters.h. Feed callbacks with pending
+*                       interrupt info. Added Doxygen & Version support.
+* 2.00a cm     05/25/11 Renamed XVTC_CTL_GACS_MASK to XVTC_CTL_GACLS_MASKl.
+*                       Added XVTC_CTL_GACPS_MASK.
+* 3.00a cjm    08/01/12 Converted from xio.h to xil_io.h, translating basic
+*                       types, MB cache functions, exceptions and assertions to
+*                       xil_io format. Replaced the following
+*                       "XExc_Init" -> "Xil_ExceptionInit"
+*                       "XExc_RegisterHandler" -> "Xil_ExceptionRegisterHandler"
+*                       "XEXC_ID_NON_CRITICAL_INT" -> "XIL_EXCEPTION_ID_INT"
+*                       "XExceptionHandler" -> "Xil_ExceptionHandler"
+*                       "XExc_mEnableExceptions" -> "Xil_ExceptionEnable"
+*                       "XEXC_NON_CRITICAL" -> "XIL_EXCEPTION_NON_CRITICAL"
+*                       "XExc_DisableExceptions" -> "Xil_ExceptionDisable"
+*                       "XExc_RemoveHandler" -> "Xil_ExceptionRemoveHandler"
+*                       "microblaze_enable_interrupts" -> "Xil_Exception
+*                                                                      Enable"
+*                       "microblaze_disable_interrupts" -> "Xil_Exception
+*                                                                       Disable"
+*
+*                       "XCOMPONENT_IS_STARTED" -> "XIL_COMPONENT_IS_STARTED"
+*                       "XCOMPONENT_IS_READY" -> "XIL_COMPONENT_IS_READY"
+*
+*                       "XASSERT_NONVOID" -> "Xil_AssertNonvoid"
+*                       "XASSERT_VOID_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XASSERT_VOID" -> "Xil_AssertVoid"
+*                       "Xil_AssertVoid_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XAssertStatus" -> "Xil_AssertStatus"
+*                       "XAssertSetCallback" -> "Xil_AssertCallback"
+*
+*                       "XASSERT_OCCURRED" -> "XIL_ASSERT_OCCURRED"
+*                       "XASSERT_NONE" -> "XIL_ASSERT_NONE"
+*
+*                       "microblaze_disable_dcache" -> "Xil_DCacheDisable"
+*                       "microblaze_enable_dcache" -> "Xil_DCacheEnable"
+*                       "microblaze_enable_icache" -> "Xil_ICacheEnable"
+*                       "microblaze_disable_icache" -> "Xil_ICacheDisable"
+*                       "microblaze_init_dcache_range" -> "Xil_DCache
+*                                                         InvalidateRange"
+*
+*                       "XCache_DisableDCache" -> "Xil_DCacheDisable"
+*                       "XCache_DisableICache" -> "Xil_ICacheDisable"
+*                       "XCache_EnableDCache" -> "Xil_DCacheEnableRegion"
+*                       "XCache_EnableICache" -> "Xil_ICacheEnableRegion"
+*                       "XCache_InvalidateDCacheLine" -> "Xil_DCache
+*                                                       InvalidateRange"
+*
+*                       "XUtil_MemoryTest32" -> "Xil_TestMem32"
+*                       "XUtil_MemoryTest16" -> "Xil_TestMem16"
+*                       "XUtil_MemoryTest8" -> "Xil_TestMem8"
+*
+*                       "xutil.h" -> "xil_testmem.h"
+*
+*                       "xbasic_types.h" -> "xil_types.h"
+*                       "xio.h" -> "xil_io.h"
+*
+*                       "XIo_In32" -> "Xil_In32"
+*                       "XIo_Out32" -> "Xil_Out32"
+*
+*                       "XTRUE" -> "TRUE"
+*                       "XFALSE" -> "FALSE"
+*                       "XNULL" -> "NULL"
+*
+*                       "Xuint8" -> "u8"
+*                       "Xuint16" -> "u16"
+*                       "Xuint32" -> "u32"
+*                       "Xint8" -> "char"
+*                       "Xint16" -> "short"
+*                       "Xint32" -> "long"
+*                       "Xfloat32" -> "float"
+*                       "Xfloat64" -> "double"
+*                       "Xboolean" -> "int"
+*                       "XTEST_FAILED" -> "XST_FAILURE"
+*                       "XTEST_PASSED" -> "XST_SUCCESS"
+* 3.00a cjm    08/02/12 Changed XVTC_RESET_RESET_MASK from 0x0000_000a
+*                       to 0x8000_0000
+* 4.00a cjm    02/07/13 Remove Unused defines: XVTC_GIER, XVTC_GIER_GIE_MASK.
+* 4.00a cjm    02/08/13 Removed XVTC_CTL_HASS_MASK.
+* 5.00a cjm    08/06/13 Replaced CTL in Polarity and Encoding register
+*                       definition with "POL" and "ENC".
+*                       Renamed XVTC_RESET_RESET_MASK to XVTC_CTL_RESET_MASK.
+*                       Renamed XVTC_SYNC_RESET_MASK to XVTC_CTL_SRST_MASK.
+*                       Renamed Error register bit defs to XVTC_ERR_*
+*                       Added Patch and Internal Revision MASKs for.
+*                       Revision register.
+* 5.00a cjm    11/01/13 Removed Unused Hori Offset registers defines from
+*                       0x0a0 - 0x0c0A
+*                       Added interlaced register defines.
+*                       Changed Version Register Revision shift from 12 to 8
+*                       and changed mask to be 8 instead of 4 bits wide
+* 5.00a cjm    11/03/13 Added Chroma/field parity bit masks.
+*                       Replaced old timing bit masks/shifts with Start/End Bit
+*                       masks/shifts.
+* 6.1   adk    08/23/14 Removed XVTC_ERR_FIL_MASK macro because it is  not
+*                       present in latest product guide.
+*                       Modified register offsets from XVTC_* to XVTC_*_OFFSET
+*                       for consistency.
+*                       Added backward compatibility macros.
+* 7.1   vns   10/14/15  Added XVTC_CTL_INTERLACE_MASK macro and
+*                       modified XVTC_CTL_ALLSS_MASK
+* 8.0   jsr   07/03/18  Added new register XVTC_GASIZE_F1_OFFSET
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XVTC_HW_H_
+#define XVTC_HW_H_	/**< prevent circular inclusions
+			  * by using protection macros */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/***************************** Include Files *********************************/
+
+#include "xil_io.h"
+
+/************************** Constant Definitions *****************************/
+
+/** @name Core Register Offsets
+* @{
+*/
+#define XVTC_CTL_OFFSET		0x000	/**< Control Register Offset */
+#define XVTC_ISR_OFFSET		0x004	/**< Status/Interrupt Status Register
+					  *  Offset */
+#define XVTC_ERROR_OFFSET	0x008	/**< Error Register Offset */
+#define XVTC_IER_OFFSET		0x00C	/**< Interrupt Enable Register
+					  *  Offset */
+#define XVTC_VER_OFFSET		0x010	/**< Version Register Offset */
+
+#define XVTC_DASIZE_OFFSET	0x020	/**< Detector Active Size Offset */
+#define XVTC_DTSTAT_OFFSET	0x024	/**< Detector Timing Status Offset */
+#define XVTC_DFENC_OFFSET	0x028	/**< Detector Encoding Offset */
+#define XVTC_DPOL_OFFSET	0x02C	/**< Detector Polarity Offset */
+#define XVTC_DHSIZE_OFFSET	0x030	/**< Detector Frame Horizontal Size
+					  *  Offset */
+#define XVTC_DVSIZE_OFFSET	0x034	/**< Detector Frame Vertical Size
+					  *  Offset */
+#define XVTC_DHSYNC_OFFSET	0x038	/**< Detector Horizontal sync
+					  *  Offset */
+
+#define XVTC_DVBHOFF_OFFSET	0x03C	/**< Detector Frame/F0 Vblank
+					  *  Horizontal Offset */
+#define XVTC_DVSYNC_OFFSET	0x040	/**< Detector Frame/F0 Vertical Sync
+					  *  Offset */
+#define XVTC_DVSHOFF_OFFSET	0x044	/**< Detector Frame/F0 Vsync Horizontal
+					  *  Offset */
+
+#define XVTC_DVBHOFF_F1_OFFSET 	0x048	/**< Detector Field 1 Vblank Horizontal
+					  *  Offset */
+#define XVTC_DVSYNC_F1_OFFSET	0x04C	/**< Detector Field 1 Vertical Sync
+					  *  Offset */
+#define XVTC_DVSHOFF_F1_OFFSET	0x050	/**< Detector Field 1 Vsync Horizontal
+					  *  Offset */
+
+#define XVTC_GASIZE_OFFSET	0x060	/**< Generator Active Size Offset */
+#define XVTC_GTSTAT_OFFSET	0x064	/**< Generator Timing Status Offset */
+#define XVTC_GFENC_OFFSET	0x068	/**< Generator Encoding Offset */
+#define XVTC_GPOL_OFFSET	0x06C	/**< Generator Polarity Offset */
+#define XVTC_GHSIZE_OFFSET	0x070	/**< Generator Frame Horizontal Size
+					  *  Offset */
+#define XVTC_GVSIZE_OFFSET	0x074	/**< Generator Frame Vertical Size
+					  *  Offset */
+#define XVTC_GHSYNC_OFFSET	0x078	/**< Generator Horizontal Sync
+					  *  Offset */
+
+#define XVTC_GVBHOFF_OFFSET	0x07C	/**< Generator Frame/F0 Vblank
+					  *  Horizontal Offset */
+#define XVTC_GVSYNC_OFFSET	0x080	/**< Generator Frame/F0 Vertical
+					  *  Sync Offset */
+#define XVTC_GVSHOFF_OFFSET	0x084	/**< Generator Frame/F0 Vsync
+					  *  horizontal Offset */
+
+#define XVTC_GVBHOFF_F1_OFFSET	0x088	/**< Generator Field 1 Vblank
+					  *  Horizontal Offset */
+#define XVTC_GVSYNC_F1_OFFSET	0x08C	/**< Generator Field 1 Vertical
+					  *  Sync Offset */
+#define XVTC_GVSHOFF_F1_OFFSET	0x090	/**< Generator Field 1 Vsync horizontal
+					  *  Offset */
+#define XVTC_GASIZE_F1_OFFSET	0x094	/**< Generator Field 1 Active Size
+					  *  Offset */
+
+#define XVTC_FS00_OFFSET	0x100	/**< Frame Sync 00 Config
+					  *  Register Offset */
+#define XVTC_FS01_OFFSET	0x104	/**< Frame Sync 01 Config
+					  *  Register Offset */
+#define XVTC_FS02_OFFSET	0x108	/**< Frame Sync 02 Config
+					  *  Register Offset */
+#define XVTC_FS03_OFFSET	0x10C	/**< Frame Sync 03 Config
+					  *  Register Offset */
+#define XVTC_FS04_OFFSET	0x110	/**< Frame Sync 04 Config
+					  *  Register Offset */
+#define XVTC_FS05_OFFSET	0x114	/**< Frame Sync 05 Config
+					  *  Register Offset */
+#define XVTC_FS06_OFFSET	0x118	/**< Frame Sync 06 Config
+					  *  Register Offset */
+#define XVTC_FS07_OFFSET	0x11C	/**< Frame Sync 07 Config
+					  *  Register Offset */
+#define XVTC_FS08_OFFSET	0x120	/**< Frame Sync 08 Config
+					  *  Register Offset */
+#define XVTC_FS09_OFFSET	0x124	/**< Frame Sync 09 Config
+					  *  Register Offset */
+#define XVTC_FS10_OFFSET	0x128	/**< Frame Sync 10 Config
+					  *  Register Offset */
+#define XVTC_FS11_OFFSET	0x12C	/**< Frame Sync 11 Config
+					  *  Register Offset */
+#define XVTC_FS12_OFFSET	0x130	/**< Frame Sync 12 Config
+					  *  Register Offset */
+#define XVTC_FS13_OFFSET	0x134	/**< Frame Sync 13 Config
+					  *  Register Offset */
+#define XVTC_FS14_OFFSET	0x138	/**< Frame Sync 14 Config
+					  *  Register Offset */
+#define XVTC_FS15_OFFSET	0x13C	/**< Frame Sync 15 Config
+					  *  Register Offset */
+
+#define XVTC_GGD_OFFSET		0x140	/**< Generator Global Delay
+					  *  Register Offset */
+/*@}*/
+
+/** @name Control Register Bit Definitions
+* @{
+*/
+#define XVTC_CTL_RESET_MASK	0x80000000 /**< Software Reset Mask */
+#define XVTC_CTL_SRST_MASK	0x40000000 /**< Frame Sync'ed Software
+					      *  Reset Mask */
+#define XVTC_CTL_FIPSS_MASK	0x04000000 /**< Field ID Output
+					      *  Polarity Source Mask */
+#define XVTC_CTL_ACPSS_MASK	0x02000000 /**< Active Chroma Output
+					      *  Polarity Source Mask */
+#define XVTC_CTL_AVPSS_MASK	0x01000000 /**< Active Video Output
+					      *  Polarity Source Mask */
+#define XVTC_CTL_HSPSS_MASK	0x00800000 /**< Horizontal Sync Output
+					      *  Polarity Source Mask */
+#define XVTC_CTL_VSPSS_MASK	0x00400000 /**< Vertical Sync Output
+					      *  Polarity Source Mask */
+#define XVTC_CTL_HBPSS_MASK	0x00200000 /**< Horizontal Blank Output
+					      *  Polarity Source Mask */
+#define XVTC_CTL_VBPSS_MASK	0x00100000 /**< Vertical Blank Output
+					      *  Polarity Source Mask */
+
+#define XVTC_CTL_INTERLACE_MASK	0x00080000 /**< Interlaced mode */
+
+#define XVTC_CTL_VCSS_MASK	0x00040000 /**< Generator Chroma Polarity
+					      *  and Encoding Source
+					      *  Select Mask */
+#define XVTC_CTL_VASS_MASK	0x00020000 /**< Generator Vertical Blank
+					      *  Offset Source Select
+					      *  Mask */
+#define XVTC_CTL_VBSS_MASK	0x00010000 /**< Generator Vertical Sync End
+					      *  (Back porch start) Source
+					      *  Select Mask */
+#define XVTC_CTL_VSSS_MASK	0x00008000 /**< Generator Vertical Sync
+					     *  Start Source Select Mask */
+#define XVTC_CTL_VFSS_MASK	0x00004000 /**< Generator Vertical Active Size
+					     *  Source Select Mask */
+#define XVTC_CTL_VTSS_MASK	0x00002000/**<  Generator Vertical Total Source
+					     *   Select (Frame Size) Mask */
+
+#define XVTC_CTL_HBSS_MASK	0x00000800 /**< Horizontal Back Porch Start
+					      *  Register Source Select
+					      *  (Sync End) Mask */
+#define XVTC_CTL_HSSS_MASK	0x00000400 /**< Horizontal Sync Start Register
+					      *  Source Select Mask */
+#define XVTC_CTL_HFSS_MASK	0x00000200 /**< Horizontal Front Porch Start
+					      *  Register Source Select
+					      *  (Active Size) Mask */
+#define XVTC_CTL_HTSS_MASK	0x00000100 /**< Horizontal Total Register
+					      *  Source Select (Frame Size)
+					      *  Mask */
+
+#define XVTC_CTL_ALLSS_MASK	0x03FDEF00 /**< Bit mask for all source
+					     *  select Mask */
+//#define XVTC_CTL_LP_MASK	0x00000008 /**< Lock Polarity */
+#define XVTC_CTL_SE_MASK	0x00000020 /**< Enable Sync with Detector */
+#define XVTC_CTL_DE_MASK	0x00000008 /**< VTC Detector Enable */
+#define XVTC_CTL_GE_MASK	0x00000004 /**< VTC Generator Enable */
+#define XVTC_CTL_RU_MASK	0x00000002 /**< VTC Register Update */
+#define XVTC_CTL_SW_MASK	0x00000001 /**< VTC Core Enable */
+/*@}*/
+
+/** @name Interrupt Status/Enable Register Bit Definitions
+* @{
+*/
+#define XVTC_IXR_FSYNC15_MASK	0x80000000 /**< Frame Sync Interrupt 15
+					      *  Mask */
+#define XVTC_IXR_FSYNC14_MASK	0x40000000 /**< Frame Sync Interrupt 14
+					      *  Mask */
+#define XVTC_IXR_FSYNC13_MASK	0x20000000 /**< Frame Sync Interrupt 13
+					      *  Mask */
+#define XVTC_IXR_FSYNC12_MASK	0x10000000 /**< Frame Sync Interrupt 12
+					      *  Mask */
+#define XVTC_IXR_FSYNC11_MASK	0x08000000 /**< Frame Sync Interrupt 11
+					      *  Mask */
+#define XVTC_IXR_FSYNC10_MASK	0x04000000 /**< Frame Sync Interrupt 10
+					      *  Mask */
+#define XVTC_IXR_FSYNC09_MASK	0x02000000 /**< Frame Sync Interrupt 09
+					      *  Mask */
+#define XVTC_IXR_FSYNC08_MASK	0x01000000 /**< Frame Sync Interrupt 08
+					      *  Mask */
+#define XVTC_IXR_FSYNC07_MASK	0x00800000 /**< Frame Sync Interrupt 07
+					      *  Mask */
+#define XVTC_IXR_FSYNC06_MASK	0x00400000 /**< Frame Sync Interrupt 06
+					      *  Mask */
+#define XVTC_IXR_FSYNC05_MASK	0x00200000 /**< Frame Sync Interrupt 05
+					      *  Mask */
+#define XVTC_IXR_FSYNC04_MASK	0x00100000 /**< Frame Sync Interrupt 04
+					      *  Mask */
+#define XVTC_IXR_FSYNC03_MASK	0x00080000 /**< Frame Sync Interrupt 03
+					      *  Mask */
+#define XVTC_IXR_FSYNC02_MASK	0x00040000 /**< Frame Sync Interrupt 02
+					      *  Mask */
+#define XVTC_IXR_FSYNC01_MASK	0x00020000 /**< Frame Sync Interrupt 01
+					      *  Mask */
+#define XVTC_IXR_FSYNC00_MASK	0x00010000 /**< Frame Sync Interrupt 00
+					      *  Mask */
+#define XVTC_IXR_FSYNCALL_MASK	0xFFFF0000 /**< All Frame Sync Interrupt 0-15
+					      *  Mask */
+
+#define XVTC_IXR_G_AV_MASK	0x00002000 /**< Generator Active Video Intr
+					      *  Mask */
+#define XVTC_IXR_G_VBLANK_MASK	0x00001000 /**< Generator VBLANK Interrupt
+					      *  Mask */
+#define XVTC_IXR_G_ALL_MASK	0x00003000 /**< All Generator interrupts
+					      *  Mask */
+
+#define XVTC_IXR_D_AV_MASK	0x00000800 /**< Detector Active Video
+					      *  Interrupt Mask */
+#define XVTC_IXR_D_VBLANK_MASK	0x00000400 /**< Detector VBLANK Interrupt
+					      *  Mask */
+#define XVTC_IXR_D_ALL_MASK	0x00000C00 /**< All Detector Interrupts
+					      *  Mask */
+
+#define XVTC_IXR_LOL_MASK	0x00000200 /**< Lock Loss Mask */
+#define XVTC_IXR_LO_MASK	0x00000100 /**< Lock Mask */
+#define XVTC_IXR_LOCKALL_MASK	0x00000300 /**< All Signal Lock interrupt
+					     *  Mask */
+
+#define XVTC_IXR_ALLINTR_MASK	(XVTC_IXR_FSYNCALL_MASK |\
+				 XVTC_IXR_G_ALL_MASK |\
+				 XVTC_IXR_D_ALL_MASK |\
+				 XVTC_IXR_LOCKALL_MASK) /**< Mask for all
+							  *  interrupts Mask */
+
+#define XVTC_IXR_SPURIOUS_INTR_MASK	~(XVTC_IXR_ALLINTR_MASK)
+
+/** @name Error Register Bit Definitions
+* @{
+*/
+#define XVTC_ERR_ACL_MASK	0x00200000	/**< Active Chroma Signal
+						  *  Lock Mask */
+#define XVTC_ERR_AVL_MASK	0x00100000	/**< Active Video Signal
+						  *  Lock Mask */
+#define XVTC_ERR_HSL_MASK	0x00080000	/**< Horizontal Sync Signal
+						  *  Lock Mask */
+#define XVTC_ERR_VSL_MASK	0x00040000	/**< Vertical Sync Signal
+						  *  Lock Mask */
+#define XVTC_ERR_HBL_MASK	0x00020000	/**< Horizontal Blank Signal
+						  *  Lock Mask */
+#define XVTC_ERR_VBL_MASK	0x00010000	/**< Vertical Blank Signal
+						  *  Lock Mask */
+/*@}*/
+
+/** @name Version Register Bit Definition and Shifts
+* @{
+*/
+#define XVTC_VER_MAJOR_MASK	0xFF000000	/**< Major Version Mask */
+#define XVTC_VER_MAJOR_SHIFT	24		/**< Major Version Bit Shift */
+#define XVTC_VER_MINOR_MASK	0x00FF0000	/**< Minor Version Mask */
+#define XVTC_VER_MINOR_SHIFT	16		/**< Minor Version Bit Shift */
+#define XVTC_VER_REV_MASK	0x0000FF00	/**< Revision Version Mask */
+#define XVTC_VER_REV_SHIFT	8		/**< Revision Version Bit
+						  *  Shift */
+#define XVTC_VER_IREV_MASK	0x000000FF	/**< Internal Revision Version
+						  *  Mask */
+#define XVTC_VER_IREV_SHIFT	0		/**< Internal Revision Bit
+						  *  Shift */
+/*@}*/
+
+/** @name Generator/Detector Active Video Size Register Bit Definitions and
+* Shift
+*  @{
+*/
+#define XVTC_ASIZE_VERT_MASK	0x1FFF0000 /**< Total number of lines
+					      *  (including blanking) for
+					      *  frame or field 1 */
+#define XVTC_ASIZE_VERT_SHIFT	16	    /**<  Bit shift for End Cycle or
+					      *   Line Count */
+#define XVTC_ASIZE_HORI_MASK	0x00001FFF /**< Horizontal Active Frame
+					      *  Size.The width of the frame
+					      *  without blanking in number
+					      *  of pixels or clocks. */
+/*@}*/
+
+/** @name Generator/Detector Status Bit Definitions
+* @{
+*/
+#define XVTC_STAT_AVIDEO_MASK	0x00000004	/**< Active Video Interrupt
+						  *  Status.Mask */
+#define XVTC_STAT_VBLANK_MASK	0x00000002	/**< Vertical Blank Interrupt
+						  *  Status Mask */
+#define XVTC_STAT_LOCKED_MASK	0x00000001	/**< Lock Status. Set High when
+						  *  all signals have locked.
+						  *  (Detector only) Mask */
+/*@}*/
+
+/** @name Generator/Detector Encoding Register Bit Definitions
+* @{
+*/
+#define XVTC_ENC_GACPS_MASK	0x00000200	/**< Generator Active Chroma
+						  *  Pixel Skip/Parity Mask */
+#define XVTC_ENC_CPARITY_MASK	0x00000100	/**< Chroma Line Parity Mask */
+#define XVTC_ENC_CPARITY_SHIFT	8		/**< Bit shift for Active
+						  *  Chroma Line Parity */
+#define XVTC_ENC_FPARITY_MASK	0x00000080	/**< Field Parity Mask  */
+#define XVTC_ENC_PROG_MASK	0x00000040	/**< Progressive/Interlaced
+						  *  Mask */
+#define XVTC_ENC_PROG_SHIFT	6			/**< Progressive/Interlaced
+						  *  Shift */
+#define XVTC_ENC_GACLS_MASK	0x00000001	/**< Generator Active Chroma
+						  *  Line Skip/parity Mask */
+/*@}*/
+
+/** @name Generator/Detector Polarity Register Bit Definitions
+* @{
+*/
+#define XVTC_POL_FIP_MASK	0x00000040	/**< Field ID Output
+						  *  Polarity Mask */
+#define XVTC_POL_ACP_MASK	0x00000020	/**< Active Chroma Output
+						  *  Polarity Mask */
+#define XVTC_POL_AVP_MASK	0x00000010	/**< Active Video Output
+						  *  Polarity Mask */
+#define XVTC_POL_HSP_MASK	0x00000008	/**< Horizontal Sync Output
+						  *  Polarity Mask */
+#define XVTC_POL_VSP_MASK	0x00000004	/**< Vertical Sync Output
+						  *  Polarity Mask */
+#define XVTC_POL_HBP_MASK	0x00000002	/**< Horizontal Blank Output
+						  *  Polarity Mask */
+#define XVTC_POL_VBP_MASK	0x00000001	/**< Vertical Blank Output
+						  *  Polarity Mask */
+#define XVTC_POL_ALLP_MASK	0x0000007F	/**< Bit mask for all
+						  *  polarity bits Mask */
+/*@}*/
+
+/** @name Generator/Detector Full Vertical Size Register Bit Definitions
+* and Shift
+* @{
+*/
+#define XVTC_VSIZE_F1_MASK	0x1FFF0000 /**< Total number of lines
+					      *  (including blanking) for
+					      *  frame or field 1 */
+#define XVTC_VSIZE_F1_SHIFT	16	/**< Bit shift for End Cycle or
+					  *  Line Count */
+#define XVTC_VSIZE_F0_MASK	0x00001FFF /**< Total number of lines
+					      *  (including blanking) for
+					      *  frame or field 0 */
+/*@}*/
+
+/** @name Generator/Detector Sync/Blank Register Bit Definitions and Shift
+* @{
+*/
+#define XVTC_SB_END_MASK	0x1FFF0000 /**< End cycle or line count
+					      *  of horizontal sync, vertical
+					      *  sync or vertical blank */
+#define XVTC_SB_END_SHIFT	16	    /**< Bit shift for End Cycle or
+					      *  Line Count */
+#define XVTC_SB_START_MASK	0x00001FFF /**< Start cycle or line count
+					      *  of horizontal sync, vertical
+					      *  sync or vertical blank */
+/*@}*/
+
+/** @name Generator/Detector VBlank/VSync Horizontal Bit Definitions and Shift
+* @{
+*/
+#define XVTC_XVXHOX_HEND_MASK	0x1FFF0000	/**< Horizontal Offset End
+						  *  Mask */
+#define XVTC_XVXHOX_HEND_SHIFT	16		/**< Horizontal End Shift */
+#define XVTC_XVXHOX_HSTART_MASK	0x00001FFF	/**< Horizontal Offset Start
+						  *  Offset */
+/*@}*/
+
+/** @name Frame Sync 00 - 15
+* @{
+*/
+#define XVTC_FSXX_VSTART_MASK	0x1FFF0000 /**< Vertical line count during
+					      *  which current Frame Sync is
+					      *  active Mask */
+#define XVTC_FSXX_VSTART_SHIFT	16	    /**< Bit shift for the vertical
+					      *  line count */
+#define XVTC_FSXX_HSTART_MASK	0x00001FFF /**< Horizontal cycle count
+					      *  during which current
+					      *  Frame Sync is active Mask */
+/*@}*/
+
+/** @name VTC Generator Global Delay Bit Definition and Shift
+* @{
+*/
+#define XVTC_GGD_VDELAY_MASK	0x1FFF0000	/**< Total lines per frame to
+						  *  delay generator output
+						  *  Mask */
+#define XVTC_GGD_VDELAY_SHIFT	16		/**< Bit shift for the total
+						  *  lines */
+#define XVTC_GGD_HDELAY_MASK	0x00001FFF	/**< Total clock cycles per
+						  *  line to delay generator
+						  *  output Mask */
+/*@}*/
+
+/** @name Compatibility Macros
+* @{
+*/
+#define XVTC_CTL	XVTC_CTL_OFFSET
+#define XVTC_ISR	XVTC_ISR_OFFSET
+#define XVTC_ERROR	XVTC_ERROR_OFFSET
+#define XVTC_IER	XVTC_IER_OFFSET
+#define XVTC_VER	XVTC_VER_OFFSET
+#define XVTC_DASIZE	XVTC_DASIZE_OFFSET
+#define XVTC_DTSTAT	XVTC_DTSTAT_OFFSET
+#define XVTC_DFENC	XVTC_DFENC_OFFSET
+#define XVTC_DPOL	XVTC_DPOL_OFFSET
+#define XVTC_DHSIZE	XVTC_DHSIZE_OFFSET
+#define XVTC_DVSIZE	XVTC_DVSIZE_OFFSET
+#define XVTC_DHSYNC	XVTC_DHSYNC_OFFSET
+#define XVTC_DVBHOFF	XVTC_DVBHOFF_OFFSET
+#define XVTC_DVSYNC	XVTC_DVSYNC_OFFSET
+#define XVTC_DVSHOFF	XVTC_DVSHOFF_OFFSET
+#define XVTC_DVBHOFF_F1	XVTC_DVBHOFF_F1_OFFSET
+#define XVTC_DVSYNC_F1	XVTC_DVSYNC_F1_OFFSET
+#define XVTC_DVSHOFF_F1	XVTC_DVSHOFF_F1_OFFSET
+#define XVTC_GASIZE	XVTC_GASIZE_OFFSET
+#define XVTC_GTSTAT	XVTC_GTSTAT_OFFSET
+#define XVTC_GFENC	XVTC_GFENC_OFFSET
+#define XVTC_GPOL	XVTC_GPOL_OFFSET
+#define XVTC_GHSIZE	XVTC_GHSIZE_OFFSET
+#define XVTC_GVSIZE	XVTC_GVSIZE_OFFSET
+#define XVTC_GHSYNC	XVTC_GHSYNC_OFFSET
+#define XVTC_GVBHOFF	XVTC_GVBHOFF_OFFSET
+#define XVTC_GVSYNC	XVTC_GVSYNC_OFFSET
+#define XVTC_GVSHOFF	XVTC_GVSHOFF_OFFSET
+#define XVTC_GVBHOFF_F1	XVTC_GVBHOFF_F1_OFFSET
+#define XVTC_GVSYNC_F1	XVTC_GVSYNC_F1_OFFSET
+#define XVTC_GVSHOFF_F1	XVTC_GVSHOFF_F1_OFFSET
+#define XVTC_FS00	XVTC_FS00_OFFSET
+#define XVTC_FS01	XVTC_FS01_OFFSET
+#define XVTC_FS02	XVTC_FS02_OFFSET
+#define XVTC_FS03	XVTC_FS03_OFFSET
+#define XVTC_FS04	XVTC_FS04_OFFSET
+#define XVTC_FS05	XVTC_FS05_OFFSET
+#define XVTC_FS06	XVTC_FS06_OFFSET
+#define XVTC_FS07	XVTC_FS07_OFFSET
+#define XVTC_FS08	XVTC_FS08_OFFSET
+#define XVTC_FS09	XVTC_FS09_OFFSET
+#define XVTC_FS10	XVTC_FS10_OFFSET
+#define XVTC_FS11	XVTC_FS11_OFFSET
+#define XVTC_FS12	XVTC_FS12_OFFSET
+#define XVTC_FS13	XVTC_FS13_OFFSET
+#define XVTC_FS14	XVTC_FS14_OFFSET
+#define XVTC_FS15	XVTC_FS15_OFFSET
+#define XVTC_GGD	XVTC_GGD_OFFSET
+/*@}*/
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/** @name Register Access Macro Definition
+* @{
+*/
+#define XVtc_In32		Xil_In32	/**< Input Operations */
+#define XVtc_Out32		Xil_Out32	/**< Output Operations */
+
+/*****************************************************************************/
+/**
+*
+* This function macro reads the given register.
+*
+* @param	BaseAddress is the base address of the VTC core.
+* @param	RegOffset is the register offset of the register (defined at
+*		top of this file).
+*
+* @return	The 32-bit value of the register.
+*
+* @note		C-style signature:
+*		u32 XVtc_ReadReg(u32 BaseAddress, u32 RegOffset)
+*
+******************************************************************************/
+#define XVtc_ReadReg(BaseAddress, RegOffset) \
+		XVtc_In32((BaseAddress) + ((u32)RegOffset))
+
+/*****************************************************************************/
+/**
+*
+* Write the given register.
+*
+* @param	BaseAddress is the base address of the VTC core.
+* @param	RegOffset is the register offset of the register (defined at
+*		top of this file) to be written.
+* @param	Data is the 32-bit value to write to the register.
+*
+* @return	None.
+*
+* @note		C-style signature:
+*		void XVtc_WriteReg(u32 BaseAddress, u32 RegOffset, u32 Data)
+*
+******************************************************************************/
+#define XVtc_WriteReg(BaseAddress, RegOffset, Data) 	\
+		XVtc_Out32((BaseAddress) + ((u32)RegOffset), (u32)(Data))
+/*@}*/
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Declarations ****************************/
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* end of protection macro */
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc_intr.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc_intr.c
@@ -0,0 +1,282 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xvtc_intr.c
+* @{
+*
+* This file contains interrupt related functions of Xilinx VTC core.
+* Please see xvtc.h for more details of the core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- -----------------------------------------------
+* 1.00a xd     08/05/08 First release
+* 1.01a xd     07/23/10 Added GIER. Added more h/w generic info into
+*                       xparameters.h. Feed callbacks with pending
+*                       interrupt info. Added Doxygen & Version support.
+* 3.00a cjm    08/01/12 Converted from xio.h to xil_io.h, translating
+*                       basic types, MB cache functions, exceptions and
+*                       assertions to xil_io format.
+*                       Replaced the following:
+*                       "XExc_Init" -> "Xil_ExceptionInit"
+*                       "XExc_RegisterHandler" -> "Xil_Exception
+*                                                 RegisterHandler"
+*                       "XEXC_ID_NON_CRITICAL_INT" -> "XIL_EXCEPTION_ID_INT"
+*                       "XExceptionHandler" -> "Xil_ExceptionHandler"
+*                       "XExc_mEnableExceptions" -> "Xil_ExceptionEnable"
+*                       "XEXC_NON_CRITICAL" -> "XIL_EXCEPTION_NON_CRITICAL"
+*                       "XExc_DisableExceptions" -> "Xil_ExceptionDisable"
+*                       "XExc_RemoveHandler" -> "Xil_ExceptionRemoveHandler"
+*                       "microblaze_enable_interrupts" -> "Xil_Exception
+*                                                         Enable"
+*                       "microblaze_disable_interrupts" -> "Xil_Exception
+*                                                           Disable"
+*                       "XCOMPONENT_IS_STARTED" -> "XIL_COMPONENT_IS_STARTED"
+*                       "XCOMPONENT_IS_READY" -> "XIL_COMPONENT_IS_READY"
+*                       "XASSERT_NONVOID" -> "Xil_AssertNonvoid"
+*                       "XASSERT_VOID_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XASSERT_VOID" -> "Xil_AssertVoid"
+*                       "Xil_AssertVoid_ALWAYS" -> "Xil_AssertVoidAlways"
+*                       "XAssertStatus" -> "Xil_AssertStatus"
+*                       "XAssertSetCallback" -> "Xil_AssertCallback"
+*
+*                       "XASSERT_OCCURRED" -> "XIL_ASSERT_OCCURRED"
+*                       "XASSERT_NONE" -> "XIL_ASSERT_NONE"
+*
+*                       "microblaze_disable_dcache" -> "Xil_DCacheDisable"
+*                       "microblaze_enable_dcache" -> "Xil_DCacheEnable"
+*                       "microblaze_enable_icache" -> "Xil_ICacheEnable"
+*                       "microblaze_disable_icache" -> "Xil_ICacheDisable"
+*                       "microblaze_init_dcache_range" -> "Xil_DCache
+*                                                        InvalidateRange"
+*
+*                       "XCache_DisableDCache" -> "Xil_DCacheDisable"
+*                       "XCache_DisableICache" -> "Xil_ICacheDisable"
+*                       "XCache_EnableDCache" -> "Xil_DCacheEnableRegion"
+*                       "XCache_EnableICache" -> "Xil_ICacheEnableRegion"
+*                       "XCache_InvalidateDCacheLine" -> "Xil_DCache
+*                                                             InvalidateRange"
+*
+*                       "XUtil_MemoryTest32" -> "Xil_TestMem32"
+*                       "XUtil_MemoryTest16" -> "Xil_TestMem16"
+*                       "XUtil_MemoryTest8" -> "Xil_TestMem8"
+*
+*                       "xutil.h" -> "xil_testmem.h"
+*
+*                       "xbasic_types.h" -> "xil_types.h"
+*                       "xio.h" -> "xil_io.h"
+*
+*                       "XIo_In32" -> "Xil_In32"
+*                       "XIo_Out32" -> "Xil_Out32"
+*
+*                       "XTRUE" -> "TRUE"
+*                       "XFALSE" -> "FALSE"
+*                       "XNULL" -> "NULL"
+*
+*                       "Xuint8" -> "u8"
+*                       "Xuint16" -> "u16"
+*                       "Xuint32" -> "u32"
+*                       "Xint8" -> "char"
+*                       "Xint16" -> "short"
+*                       "Xint32" -> "long"
+*                       "Xfloat32" -> "float"
+*                       "Xfloat64" -> "double"
+*                       "Xboolean" -> "int"
+*                       "XTEST_FAILED" -> "XST_FAILURE"
+*                       "XTEST_PASSED" -> "XST_SUCCESS"
+* 6.1   adk    08/23/14 Alligned doxygen tags.
+* 8.1   pg     04/03/20  Fixed interrupt handler issue
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xvtc.h"
+
+/************************** Constant Definitions *****************************/
+
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function is the interrupt handler for the VTC core.
+*
+* This handler reads the pending interrupt from the IER/ISR, determines the
+* source of the interrupts, calls according callbacks and finally clears the
+* interrupts.
+*
+* The application is responsible for connecting this function to the interrupt
+* system. Application beyond this driver is also responsible for providing
+* callbacks to handle interrupts and installing the callbacks using
+* XVtc_SetCallBack() during initialization phase.
+*
+* @param	InstancePtr is a pointer to the XVtc instance that just
+*		interrupted.
+*
+* @return	None.
+*
+* @note		None.
+*
+******************************************************************************/
+void XVtc_IntrHandler(void *InstancePtr)
+{
+	u32 PendingIntr;
+	u32 ErrorStatus;
+	XVtc *XVtcPtr = (XVtc *) InstancePtr;
+
+	/* Verify arguments. */
+	Xil_AssertVoid(XVtcPtr != NULL);
+	Xil_AssertVoid(XVtcPtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* Get pending interrupts */
+	PendingIntr = XVtc_IntrGetPending(XVtcPtr);
+
+	/* Clear pending interrupt(s) */
+	XVtc_IntrClear(XVtcPtr, PendingIntr);
+
+	/* Spurious interrupt has happened */
+	if (PendingIntr & XVTC_IXR_SPURIOUS_INTR_MASK) {
+		ErrorStatus = 0;
+		XVtcPtr->ErrCallBack(XVtcPtr->ErrRef, ErrorStatus);
+		return;
+	}
+
+	/* A generator event has happened */
+	if ((PendingIntr & XVTC_IXR_G_ALL_MASK))
+		XVtcPtr->GeneratorCallBack(XVtcPtr->GeneratorRef,
+		PendingIntr);
+
+	/* A detector event has happened */
+	if ((PendingIntr & XVTC_IXR_D_ALL_MASK))
+		XVtcPtr->DetectorCallBack(XVtcPtr->DetectorRef,
+		PendingIntr);
+
+	/* A frame sync is done */
+	if ((PendingIntr & XVTC_IXR_FSYNCALL_MASK))
+		XVtcPtr->FrameSyncCallBack(XVtcPtr->FrameSyncRef,
+		PendingIntr);
+
+	/* A signal lock is detected */
+	if ((PendingIntr & XVTC_IXR_LOCKALL_MASK))
+		XVtcPtr->LockCallBack(XVtcPtr->LockRef,
+		PendingIntr);
+}
+
+
+/*****************************************************************************/
+/**
+*
+* This routine installs an asynchronous callback function for the given
+* HandlerType:
+*
+* <pre>
+* HandlerType              Callback Function Type
+* -----------------------  --------------------------------------------------
+* XVTC_HANDLER_FRAMESYNC   XVtc_FrameSyncCallBack
+* XVTC_HANDLER_LOCK        XVtc_LockCallBack
+* XVTC_HANDLER_DETECTOR    XVtc_DetectorCallBack
+* XVTC_HANDLER_GENERATOR   XVtc_GeneratorCallBack
+* XVTC_HANDLER_ERROR       XVtc_ErrCallBack
+*
+* HandlerType              Invoked by this driver when:
+* -----------------------  --------------------------------------------------
+* XVTC_HANDLER_FRAMESYNC   A frame sync event happens
+* XVTC_HANDLER_LOCK        A signal lock event happens
+* XVTC_HANDLER_DETECTOR    A detector related event happens
+* XVTC_HANDLER_GENERATOR   A generator related event happens
+* XVTC_HANDLER_ERROR       An error condition happens
+* </pre>
+*
+* @param	InstancePtr is a pointer to the XVtc instance to be worked
+*		on.
+* @param	HandlerType specifies which callback is to be attached.
+* @param	CallBackFunc is the address of the callback function.
+* @param	CallBackRef is a user data item that will be passed to the
+*		callback function when it is invoked.
+*
+* @return
+*		- XST_SUCCESS when handler is installed.
+*		- XST_INVALID_PARAM when HandlerType is invalid.
+*
+* @note		Invoking this function for a handler that already has been
+*		installed replaces it with the new handler.
+*
+******************************************************************************/
+int XVtc_SetCallBack(XVtc *InstancePtr, u32 HandlerType,
+				void *CallBackFunc, void *CallBackRef)
+{
+
+	/* Verify arguments. */
+	Xil_AssertNonvoid(InstancePtr != NULL);
+	Xil_AssertNonvoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
+
+	/* For specific handler type assigning callback function reference */
+	switch (HandlerType) {
+	case XVTC_HANDLER_FRAMESYNC:
+		InstancePtr->FrameSyncCallBack =
+				(XVtc_CallBack) CallBackFunc;
+		InstancePtr->FrameSyncRef = CallBackRef;
+		break;
+
+	case XVTC_HANDLER_LOCK:
+		InstancePtr->LockCallBack = (XVtc_CallBack) CallBackFunc;
+		InstancePtr->LockRef = CallBackRef;
+		break;
+
+	case XVTC_HANDLER_DETECTOR:
+		InstancePtr->DetectorCallBack =
+				(XVtc_CallBack) CallBackFunc;
+		InstancePtr->DetectorRef = CallBackRef;
+		break;
+
+	case XVTC_HANDLER_GENERATOR:
+		InstancePtr->GeneratorCallBack =
+				(XVtc_CallBack) CallBackFunc;
+		InstancePtr->GeneratorRef = CallBackRef;
+		break;
+
+	case XVTC_HANDLER_ERROR:
+		InstancePtr->ErrCallBack =
+				(XVtc_ErrorCallBack) CallBackFunc;
+		InstancePtr->ErrRef = CallBackRef;
+		break;
+
+	default:
+		return XST_INVALID_PARAM;
+
+	}
+	return XST_SUCCESS;
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc_sinit.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmi-tx/xvtc_sinit.c
@@ -0,0 +1,105 @@
+/******************************************************************************
+*
+ *
+ * Copyright (C) 2015, 2016, 2017 Xilinx, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xvtc_sinit.c
+* @{
+*
+* This file contains static initialization methods for Xilinx VTC core.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver   Who    Date     Changes
+* ----- ------ -------- --------------------------------------------------
+* 1.00a xd     08/05/08 First release.
+* 1.01a xd     07/23/10 Added GIER; Added more h/w generic info into
+*                       xparameters.h. Feed callbacks with pending
+*                       interrupt info. Added Doxygen & Version support.
+* 3.00a cjm    08/01/12 Converted from xio.h to xil_io.h, translating
+*                       basic types, MB cache functions, exceptions and
+*                       assertions to xil_io format.
+*                       Replaced the following:
+*                       "Xuint16" -> "u16".
+* 6.1   adk    08/23/14 updated doxygen tags.
+* 7.1   als    08/11/16 Provide protection against driver inclusion in the
+*                       absence of VTC instantiation.
+* </pre>
+*
+******************************************************************************/
+
+/***************************** Include Files *********************************/
+
+#include "xvtc.h"
+
+/************************** Constant Definitions *****************************/
+
+#ifndef XPAR_XVTC_NUM_INSTANCES
+#define XPAR_XVTC_NUM_INSTANCES 0
+#endif
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+
+/**************************** Type Definitions *******************************/
+
+
+/************************** Function Prototypes ******************************/
+
+
+/************************** Variable Definitions *****************************/
+
+
+/************************** Function Definitions *****************************/
+
+/*****************************************************************************/
+/**
+*
+* This function returns a reference to an XVtc_Config structure based on the
+* core id, <i>DeviceId</i>. The return value will refer to an entry in
+* the device configuration table defined in the xvtc_g.c file.
+*
+* @param	DeviceId is the unique core ID of the VTC core for the lookup
+*		operation.
+*
+* @return	XVtc_LookupConfig returns a reference to a config record in
+*		the configuration table (in xvtc_g.c) corresponding to
+*		<i>DeviceId</i>, or NULL if no match is found.
+*
+* @note		None.
+*
+******************************************************************************/
+XVtc_Config *XVtc_LookupConfig(u16 DeviceId)
+{
+	extern XVtc_Config XVtc_ConfigTable[];
+	XVtc_Config *CfgPtr = NULL;
+	int i;
+
+	/* Checking for device id for which instance it is matching */
+	for (i = 0; i < XPAR_XVTC_NUM_INSTANCES; i++) {
+		/* Assigning address of config table if both device ids
+		 * are matched
+		 */
+		if (XVtc_ConfigTable[i].DeviceId == DeviceId) {
+			CfgPtr = &XVtc_ConfigTable[i];
+			break;
+		}
+	}
+
+	return CfgPtr;
+}
+/** @} */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmirx.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx-hdmirx.c
@@ -0,0 +1,2688 @@
+/*
+ * Xilinx Video HDMI RX Subsystem driver implementing a V4L2 subdevice
+ *
+ * Copyright (C) 2016-2017 Leon Woestenberg <leon@sidebranch.com>
+ * Copyright (C) 2016-2017 Xilinx, Inc.
+ *
+ * Authors: Leon Woestenberg <leon@sidebranch.com>
+ *          Rohit Consul <rohitco@xilinx.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/xilinx-v4l2-controls.h>
+#include <linux/v4l2-dv-timings.h>
+#include <linux/firmware.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/hdmi.h>
+#include <linux/version.h>
+#include <media/hdr-ctrls.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-subdev.h>
+#include <media/v4l2-dv-timings.h>
+
+#include "linux/phy/phy-vphy.h"
+
+/* baseline driver includes */
+#include "xilinx-hdmi-rx/xv_hdmirxss.h"
+
+/* for the HMAC, using password to decrypt HDCP keys */
+#include "phy-xilinx-vphy/xhdcp22_common.h"
+#include "phy-xilinx-vphy/aes256.h"
+#include "xlnx_hdmirx_audio.h"
+
+#define hdmi_mutex_lock(x) mutex_lock(x)
+#define hdmi_mutex_unlock(x) mutex_unlock(x)
+
+
+#define HDMI_MAX_LANES	4
+#define EDID_BLOCKS_MAX 10
+#define EDID_BLOCK_SIZE 128
+
+/* RX Subsystem Sub-core offsets */
+#define RXSS_RX_OFFSET				0x00000u
+#define RXSS_HDCP14_OFFSET			0x10000u
+#define RXSS_HDCP14_TIMER_OFFSET	0x20000u
+#define RXSS_HDCP22_OFFSET			0x40000u
+/* HDCP22 sub-core offsets */
+#define RX_HDCP22_CIPHER_OFFSET		0x00000u
+#define RX_HDCP2_MMULT_OFFSET		0x10000u
+#define RX_HDCP22_TIMER_OFFSET		0x20000u
+#define RX_HDCP22_RNG_OFFSET		0x30000u
+
+struct xhdmi_device {
+	struct device *dev;
+	void __iomem *iomem;
+	void __iomem *hdcp1x_keymngmt_iomem;
+
+	/* clocks */
+	struct clk *clk;
+	struct clk *axi_lite_clk;
+
+	/* HDMI RXSS interrupt number */
+	int irq;
+	/* HDCP interrupt numbers */
+	int hdcp1x_irq;
+	int hdcp1x_timer_irq;
+	int hdcp22_irq;
+	int hdcp22_timer_irq;
+	/* status */
+	bool hdcp_authenticated;
+	bool hdcp_encrypted;
+	bool hdcp_password_accepted;
+	/* delayed work to drive HDCP poll */
+	struct delayed_work delayed_work_hdcp_poll;
+
+	bool teardown;
+	struct phy *phy[HDMI_MAX_LANES];
+
+	/* mutex to prevent concurrent access to this structure */
+	struct mutex xhdmi_mutex;
+	/* protects concurrent access from interrupt context */
+	spinlock_t irq_lock;
+
+	/* schedule (future) work */
+	struct workqueue_struct *work_queue;
+	struct delayed_work delayed_work_enable_hotplug;
+
+	struct v4l2_subdev subdev;
+
+	/* V4L media output pad to construct the video pipeline */
+	struct media_pad pad;
+	struct v4l2_mbus_framefmt detected_format;
+	struct v4l2_dv_timings detected_timings;
+	const struct xvip_video_format *vip_format;
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	bool cable_is_connected;
+	bool hdmi_stream_is_up;
+
+	/* copy of user specified EDID block, if any */
+	u8 edid_user[EDID_BLOCKS_MAX * EDID_BLOCK_SIZE];
+	/* number of actual blocks valid in edid_user */
+	int edid_user_blocks;
+
+	/* number of EDID blocks supported by IP */
+	int edid_blocks_max;
+
+	/* configuration for the baseline subsystem driver instance */
+	XV_HdmiRxSs_Config config;
+	/* bookkeeping for the baseline subsystem driver instance */
+	XV_HdmiRxSs xv_hdmirxss;
+	/* sub core interrupt status registers */
+	u32 IntrStatus[7];
+	/* pointer to xvphy */
+	XVphy *xvphy;
+	/* pointer to HDMI GT controller phy */
+	XHdmiphy1 *xgtphy;
+	/* flag to determine which phy */
+	u32 isvphy;
+	/* HDCP keys */
+	u8 hdcp_password[32];
+	u8 Hdcp22Lc128[16];
+	u8 Hdcp22PrivateKey[902];
+	u8 Hdcp14KeyA[328];
+	u8 Hdcp14KeyB[328];
+	/* flag to indicate audio is enabled in device tree */
+	bool audio_enabled;
+	/* flag to indicate audio is initialized */
+	bool audio_init;
+	/* audio data to be shared with audio module */
+	struct xlnx_hdmirx_audio_data *rx_audio_data;
+};
+
+// Xilinx EDID
+static const u8 xilinx_edid[] = {
+	0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x61, 0x98, 0x34, 0x12, 0x78, 0x56, 0x34, 0x12,
+	0x0E, 0x1C, 0x01, 0x03, 0x80, 0xA0, 0x5A, 0x78, 0x0A, 0xEE, 0x91, 0xA3, 0x54, 0x4C, 0x99, 0x26,
+	0x0F, 0x50, 0x54, 0x21, 0x08, 0x00, 0x71, 0x4F, 0x81, 0xC0, 0x81, 0x00, 0x81, 0x80, 0x95, 0x00,
+	0xA9, 0xC0, 0xB3, 0x00, 0x01, 0x01, 0x08, 0xE8, 0x00, 0x30, 0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58,
+	0x8A, 0x00, 0x40, 0x84, 0x63, 0x00, 0x00, 0x1E, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
+	0x58, 0x2C, 0x45, 0x00, 0x40, 0x84, 0x63, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x18,
+	0x4B, 0x0F, 0x8C, 0x3C, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
+	0x00, 0x58, 0x49, 0x4C, 0x49, 0x4E, 0x58, 0x20, 0x48, 0x44, 0x4D, 0x49, 0x0A, 0x20, 0x01, 0x85,
+
+	0x02, 0x03, 0x3F, 0xF5, 0x57, 0x61, 0x10, 0x1F, 0x04, 0x13, 0x05, 0x14, 0x20, 0x21, 0x22, 0x5D,
+	0x5E, 0x5F, 0x60, 0x65, 0x66, 0x62, 0x63, 0x64, 0x07, 0x16, 0x03, 0x12, 0x23, 0x0F, 0x07, 0x07,
+	0x83, 0x6F, 0x00, 0x00, 0x6B, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x78, 0x3C, 0x20, 0x00, 0x20, 0x03,
+	0x67, 0xD8, 0x5D, 0xC4, 0x01, 0x78, 0x80, 0x07, 0xE3, 0x0F, 0x01, 0xE0, 0xE2, 0x00, 0xCF, 0x02,
+	0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45, 0x00, 0x20, 0xC2, 0x31, 0x00, 0x00,
+	0x1E, 0x08, 0xE8, 0x00, 0x30, 0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58, 0x8A, 0x00, 0x20, 0xC2, 0x31,
+	0x00, 0x00, 0x1E, 0x04, 0x74, 0x00, 0x30, 0xF2, 0x70, 0x5A, 0x80, 0xB0, 0x58, 0x8A, 0x00, 0x20,
+	0x52, 0x31, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xDC
+};
+
+static inline struct xhdmi_device *to_xhdmi(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xhdmi_device, subdev);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Core Operations
+ */
+
+static const struct v4l2_event xhdmi_ev_fmt = {
+	.type = V4L2_EVENT_SOURCE_CHANGE,
+	.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
+};
+
+static int xhdmi_subscribe_event(struct v4l2_subdev *sd, struct v4l2_fh *fh, struct v4l2_event_subscription *sub)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(sd);
+	switch (sub->type) {
+		case V4L2_EVENT_SOURCE_CHANGE:
+		{
+			int rc;
+			rc = v4l2_src_change_event_subdev_subscribe(sd, fh, sub);
+			dev_dbg(xhdmi->dev, "xhdmi_subscribe_event(V4L2_EVENT_SOURCE_CHANGE) = %d\n", rc);
+			return rc;
+		}
+#if 0
+		case V4L2_EVENT_CTRL:
+			return v4l2_ctrl_subdev_subscribe_event(sd, fh, sub);
+#endif
+		default:
+		{
+			dev_dbg(xhdmi->dev, "xhdmi_subscribe_event() default: -EINVAL\n");
+			return -EINVAL;
+		}
+	}
+}
+
+ /* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Video Operations
+ */
+
+static int xhdmi_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	/* HDMI does not need to be enabled when we start streaming */
+	dev_dbg(xhdmi->dev, "xhdmi_s_stream enable = %d\n", enable);
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Pad Operations
+ */
+
+ /* https://linuxtv.org/downloads/v4l-dvb-apis/vidioc-dv-timings-cap.html */
+
+/* https://linuxtv.org/downloads/v4l-dvb-apis/vidioc-subdev-g-fmt.html */
+static struct v4l2_mbus_framefmt *
+__xhdmi_get_pad_format_ptr(struct xhdmi_device *xhdmi,
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+		struct v4l2_subdev_pad_config *cfg,
+#else
+		struct v4l2_subdev_state *sd_state,
+#endif
+		unsigned int pad, u32 which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		dev_dbg(xhdmi->dev, "__xhdmi_get_pad_format(): V4L2_SUBDEV_FORMAT_TRY\n");
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+		return v4l2_subdev_get_try_format(&xhdmi->subdev, cfg, pad);
+#else
+		return v4l2_subdev_get_try_format(&xhdmi->subdev, sd_state, pad);
+#endif
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		dev_dbg(xhdmi->dev, "__xhdmi_get_pad_format(): V4L2_SUBDEV_FORMAT_ACTIVE\n");
+		dev_dbg(xhdmi->dev, "detected_format->width = %u\n", xhdmi->detected_format.width);
+		return &xhdmi->detected_format;
+	default:
+		return NULL;
+	}
+}
+
+static int xhdmi_get_format(struct v4l2_subdev *subdev,
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+			   struct v4l2_subdev_pad_config *cfg,
+#else
+			   struct v4l2_subdev_state *sd_state,
+#endif
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	struct v4l2_mbus_framefmt *gfmt;
+
+	dev_dbg(xhdmi->dev, "xhdmi_get_format\n");
+
+	if (fmt->pad > 0)
+		return -EINVAL;
+
+	/* copy either try or currently-active (i.e. detected) format to caller */
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+	gfmt = __xhdmi_get_pad_format_ptr(xhdmi, cfg, fmt->pad, fmt->which);
+#else
+	gfmt = __xhdmi_get_pad_format_ptr(xhdmi, sd_state, fmt->pad, fmt->which);
+#endif
+	if (!gfmt)
+		return -EINVAL;
+	fmt->format = *gfmt;
+
+	dev_dbg(xhdmi->dev, "xhdmi_get_format, height = %u\n", fmt->format.height);
+
+	return 0;
+}
+
+/* we must modify the requested format to match what the hardware can provide */
+static int xhdmi_set_format(struct v4l2_subdev *subdev,
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+			   struct v4l2_subdev_pad_config *cfg,
+#else
+			   struct v4l2_subdev_state *sd_state,
+#endif
+			   struct v4l2_subdev_format *fmt)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	dev_dbg(xhdmi->dev,"xhdmi_set_format\n");
+	if (fmt->pad > 0)
+		return -EINVAL;
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	/* there is nothing we can take from the format requested by the caller,
+	 * by convention we must return the active (i.e. detected) format */
+	fmt->format = xhdmi->detected_format;
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+	return 0;
+}
+
+/* https://linuxtv.org/downloads/v4l-dvb-apis-new/media/kapi/v4l2-subdev.html#v4l2-sub-device-functions-and-data-structures
+ * https://linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-edid.html
+ */
+static int xhdmi_get_edid(struct v4l2_subdev *subdev, struct v4l2_edid *edid) {
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	int do_copy = 1;
+	if (edid->pad > 0)
+		return -EINVAL;
+	if (edid->start_block != 0)
+		return -EINVAL;
+	/* caller is only interested in the size of the EDID? */
+	if ((edid->start_block == 0) && (edid->blocks == 0)) do_copy = 0;
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	/* user EDID active? */
+	if (xhdmi->edid_user_blocks) {
+		if (do_copy)
+			memcpy(edid->edid, xhdmi->edid_user,
+			       128 * (u16)xhdmi->edid_user_blocks);
+		edid->blocks = xhdmi->edid_user_blocks;
+	} else {
+		if (do_copy)
+			memcpy(edid->edid, &xilinx_edid[0], sizeof(xilinx_edid));
+		edid->blocks = sizeof(xilinx_edid) / 128;
+	}
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+	return 0;
+}
+
+static void xhdmi_set_hpd(struct xhdmi_device *xhdmi, int enable)
+{
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	XV_HdmiRx_SetHpd(HdmiRxSsPtr->HdmiRxPtr, enable);
+}
+
+static void xhdmi_delayed_work_enable_hotplug(struct work_struct *work)
+{
+	struct delayed_work *dwork = to_delayed_work(work);
+	struct xhdmi_device *xhdmi = container_of(dwork, struct xhdmi_device,
+						delayed_work_enable_hotplug);
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+
+	XV_HdmiRx_SetHpd(HdmiRxSsPtr->HdmiRxPtr, 1);
+}
+
+static int xhdmi_set_edid(struct v4l2_subdev *subdev, struct v4l2_edid *edid) {
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	if (edid->pad > 0)
+		return -EINVAL;
+	if (edid->start_block != 0)
+		return -EINVAL;
+	if (edid->blocks > xhdmi->edid_blocks_max) {
+		/* notify caller of how many EDID blocks this driver supports */
+		edid->blocks = xhdmi->edid_blocks_max;
+		return -E2BIG;
+	}
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	xhdmi->edid_user_blocks = edid->blocks;
+
+	/* Disable hotplug and I2C access to EDID RAM from DDC port */
+	cancel_delayed_work_sync(&xhdmi->delayed_work_enable_hotplug);
+	xhdmi_set_hpd(xhdmi, 0);
+
+	if (edid->blocks) {
+		memcpy(xhdmi->edid_user, edid->edid, 128 * edid->blocks);
+		XV_HdmiRxSs_LoadEdid(HdmiRxSsPtr, (u8 *)&xhdmi->edid_user,
+				     128 * (u16)xhdmi->edid_user_blocks);
+		/* enable hotplug after 100 ms */
+		queue_delayed_work(xhdmi->work_queue,
+				&xhdmi->delayed_work_enable_hotplug, HZ / 10);
+	}
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdevice Operations
+ */
+
+static int xhdmi_enum_frame_size(struct v4l2_subdev *subdev,
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+				struct v4l2_subdev_pad_config *cfg,
+#else
+				struct v4l2_subdev_state *sd_state,
+#endif
+				struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->pad > 0)
+		return -EINVAL;
+	/* we support a non-discrete set, i.e. contiguous range of frame sizes,
+	 * do not return a discrete set */
+	return 0;
+}
+
+/**
+ * xhdmi_enum_mbus_code - Enumerate the media format code
+ * @subdev: V4L2 subdevice
+ * @sd_state: V4L2 subdev state
+ * @code: returning media bus code
+ *
+ * Enumerate the media bus code of the subdevice. Return the corresponding
+ * pad format code. This function only works for subdevices with fixed format
+ * on all pads. Subdevices with multiple format should have their own
+ * function to enumerate mbus codes.
+ *
+ * Return: 0 if the media bus code is found, or -EINVAL if the format index
+ * is not valid.
+ */
+int xhdmi_enum_mbus_code(struct v4l2_subdev *subdev,
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+		struct v4l2_subdev_pad_config *cfg,
+#else
+		struct v4l2_subdev_state *sd_state,
+#endif
+		struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct v4l2_mbus_framefmt *format;
+
+	/* Enumerating frame sizes based on the active configuration isn't
+	 * supported yet.
+	 */
+	if (code->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+		return -EINVAL;
+
+	if (code->index)
+		return -EINVAL;
+
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(5, 15, 0))
+	format = v4l2_subdev_get_try_format(subdev, cfg, code->pad);
+#else
+	format = v4l2_subdev_get_try_format(subdev, sd_state, code->pad);
+#endif
+
+	code->code = format->code;
+
+	return 0;
+}
+
+static int xhdmi_dv_timings_cap(struct v4l2_subdev *subdev,
+		struct v4l2_dv_timings_cap *cap)
+{
+	if (cap->pad != 0)
+		return -EINVAL;
+	cap->type = V4L2_DV_BT_656_1120;
+	cap->bt.max_width = 4096;
+	cap->bt.max_height = 2160;
+	cap->bt.min_pixelclock = 25000000;
+	cap->bt.max_pixelclock = 297000000;
+	cap->bt.standards = V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT |
+			 V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT;
+	cap->bt.capabilities = V4L2_DV_BT_CAP_PROGRESSIVE |
+		V4L2_DV_BT_CAP_REDUCED_BLANKING | V4L2_DV_BT_CAP_CUSTOM;
+	return 0;
+}
+
+static int xhdmi_query_dv_timings(struct v4l2_subdev *subdev,
+			struct v4l2_dv_timings *timings)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+
+	if (!timings)
+		return -EINVAL;
+
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	if (!xhdmi->hdmi_stream_is_up) {
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		return -ENOLINK;
+	}
+
+	/* copy detected timings into destination */
+	*timings = xhdmi->detected_timings;
+
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+	return 0;
+}
+
+/* struct v4l2_subdev_internal_ops.open */
+static int xhdmi_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	dev_dbg(xhdmi->dev,"xhdmi_open\n");
+	return 0;
+}
+
+/* struct v4l2_subdev_internal_ops.close */
+static int xhdmi_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xhdmi_device *xhdmi = to_xhdmi(subdev);
+	dev_dbg(xhdmi->dev,"xhdmi_close\n");
+	return 0;
+}
+
+static int xhdmi_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	return 0;
+}
+
+static int xhdmi_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
+{
+	int ret = 0;
+	struct xhdmi_device *xhdmi =
+			container_of(ctrl->handler,
+					struct xhdmi_device,
+					ctrl_handler);
+	XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	struct v4l2_metadata_hdr *hdr_ptr;
+
+	switch (ctrl->id)  {
+	case V4L2_CID_METADATA_HDR:
+		{
+			hdr_ptr = (struct v4l2_metadata_hdr *) ctrl->p_new.p;
+			hdr_ptr->metadata_type = V4L2_HDR_TYPE_HDR10;
+			hdr_ptr->size = sizeof(struct v4l2_hdr10_payload);
+			memcpy (hdr_ptr->payload,
+					&HdmiRxSsPtr->DrmInfoframe,
+					hdr_ptr->size);
+			break;
+		}
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops xhdmi_ctrl_ops = {
+	.s_ctrl	= xhdmi_s_ctrl,
+	.g_volatile_ctrl = xhdmi_g_volatile_ctrl,
+};
+
+static const struct v4l2_ctrl_config xhdmi_ctrls[] = {
+	{
+		.ops = &xhdmi_ctrl_ops,
+		.id = V4L2_CID_METADATA_HDR,
+		.name = "HDR Controls",
+		.type = V4L2_CTRL_TYPE_HDR,
+		.min = 0x8000000000000000,
+		.max = 0x7FFFFFFFFFFFFFFF,
+		.step = 1,
+		.def = 0,
+		.elem_size = sizeof(struct v4l2_metadata_hdr),
+		.flags = V4L2_CTRL_FLAG_VOLATILE | V4L2_CTRL_FLAG_HAS_PAYLOAD,
+	}
+};
+static struct v4l2_subdev_core_ops xhdmi_core_ops = {
+	.subscribe_event = xhdmi_subscribe_event,
+	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static struct v4l2_subdev_video_ops xhdmi_video_ops = {
+	.s_stream = xhdmi_s_stream,
+	.query_dv_timings = xhdmi_query_dv_timings,
+};
+
+/* If the subdev driver intends to process video and integrate with the media framework,
+ * it must implement format related functionality using v4l2_subdev_pad_ops instead of
+ * v4l2_subdev_video_ops. */
+static struct v4l2_subdev_pad_ops xhdmi_pad_ops = {
+	.enum_mbus_code		= xhdmi_enum_mbus_code,
+	.enum_frame_size	= xhdmi_enum_frame_size,
+	.get_fmt			= xhdmi_get_format,
+	.set_fmt			= xhdmi_set_format,
+	.get_edid			= xhdmi_get_edid,
+	.set_edid			= xhdmi_set_edid,
+	.dv_timings_cap		= xhdmi_dv_timings_cap,
+};
+
+static struct v4l2_subdev_ops xhdmi_ops = {
+	.core   = &xhdmi_core_ops,
+	.video  = &xhdmi_video_ops,
+	.pad    = &xhdmi_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops xhdmi_internal_ops = {
+	.open	= xhdmi_open,
+	.close	= xhdmi_close,
+};
+
+/* -----------------------------------------------------------------------------
+ * Media Operations
+ */
+
+static const struct media_entity_operations xhdmi_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+/* -----------------------------------------------------------------------------
+ * Power Management
+ */
+
+void HdmiRx_PioIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_TmrIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_VtdIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_DdcIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_AuxIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_AudIntrHandler(XV_HdmiRx *InstancePtr);
+void HdmiRx_LinkStatusIntrHandler(XV_HdmiRx *InstancePtr);
+
+static void XV_HdmiRxSs_IntrEnable(XV_HdmiRxSs *HdmiRxSsPtr)
+{
+	XV_HdmiRx_PioIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_TmrIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_VtdIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_DdcIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_AuxIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_AudioIntrEnable(HdmiRxSsPtr->HdmiRxPtr);
+}
+
+static void XV_HdmiRxSs_IntrDisable(XV_HdmiRxSs *HdmiRxSsPtr)
+{
+	XV_HdmiRx_PioIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_TmrIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_VtdIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_DdcIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_AuxIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_AudioIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+	XV_HdmiRx_LinkIntrDisable(HdmiRxSsPtr->HdmiRxPtr);
+}
+
+static int __maybe_unused hdmirx_pm_suspend(struct device *dev)
+{
+	unsigned long flags;
+	struct xhdmi_device *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	dev_dbg(xhdmi->dev,"HDMI RX suspend function called\n");
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiRxSs_IntrDisable(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+	return 0;
+}
+
+static int __maybe_unused hdmirx_pm_resume(struct device *dev)
+{
+	unsigned long flags;
+	struct xhdmi_device *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	dev_dbg(xhdmi->dev,"HDMI RX resume function called\n");
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiRxSs_IntrEnable(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+	return 0;
+}
+
+static irqreturn_t hdmirx_irq_handler(int irq, void *dev_id)
+{
+	struct xhdmi_device *xhdmi;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	unsigned long flags;
+	xhdmi = (struct xhdmi_device *)dev_id;
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	if (HdmiRxSsPtr->IsReady != XIL_COMPONENT_IS_READY) {
+		printk(KERN_INFO "hdmirx_irq_handler(): HDMI RX SS is not initialized?!\n");
+	}
+
+	/* read status registers */
+	xhdmi->IntrStatus[0] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_PIO_STA_OFFSET)) & (XV_HDMIRX_PIO_STA_IRQ_MASK);
+	xhdmi->IntrStatus[1] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_TMR_STA_OFFSET)) & (XV_HDMIRX_TMR_STA_IRQ_MASK);
+	xhdmi->IntrStatus[2] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_VTD_STA_OFFSET)) & (XV_HDMIRX_VTD_STA_IRQ_MASK);
+	xhdmi->IntrStatus[3] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_DDC_STA_OFFSET)) & (XV_HDMIRX_DDC_STA_IRQ_MASK);
+	xhdmi->IntrStatus[4] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_AUX_STA_OFFSET)) & (XV_HDMIRX_AUX_STA_IRQ_MASK);
+	xhdmi->IntrStatus[5] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_AUD_STA_OFFSET)) & (XV_HDMIRX_AUD_STA_IRQ_MASK);
+	xhdmi->IntrStatus[6] = XV_HdmiRx_ReadReg(HdmiRxSsPtr->HdmiRxPtr->Config.BaseAddress, (XV_HDMIRX_LNKSTA_STA_OFFSET)) & (XV_HDMIRX_LNKSTA_STA_IRQ_MASK);
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	/* mask interrupt request */
+	XV_HdmiRxSs_IntrDisable(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* call bottom-half */
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t hdmirx_irq_thread(int irq, void *dev_id)
+{
+	struct xhdmi_device *xhdmi;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	unsigned long flags;
+
+	xhdmi = (struct xhdmi_device *)dev_id;
+	if (xhdmi->teardown) {
+		printk(KERN_INFO "irq_thread: teardown\n");
+		return IRQ_HANDLED;
+	}
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	/* call baremetal interrupt handler, this in turn will
+	 * call the registed callbacks functions */
+
+	if (xhdmi->IntrStatus[0]) HdmiRx_PioIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+	if (xhdmi->IntrStatus[1]) HdmiRx_TmrIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+	if (xhdmi->IntrStatus[2]) HdmiRx_VtdIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+	if (xhdmi->IntrStatus[3]) HdmiRx_DdcIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+	if (xhdmi->IntrStatus[4]) HdmiRx_AuxIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+	if (xhdmi->IntrStatus[5]) HdmiRx_AudIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+	if (xhdmi->IntrStatus[6]) HdmiRx_LinkStatusIntrHandler(HdmiRxSsPtr->HdmiRxPtr);
+
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	/* unmask interrupt request */
+	XV_HdmiRxSs_IntrEnable(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+
+/* top-half interrupt handler for HDMI RX HDCP */
+static irqreturn_t hdmirx_hdcp_irq_handler(int irq, void *dev_id)
+{
+	struct xhdmi_device *xhdmi;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	unsigned long flags;
+	xhdmi = (struct xhdmi_device *)dev_id;
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	/* mask/disable interrupt requests */
+	if (irq == xhdmi->hdcp1x_irq) {
+		XHdcp1x_WriteReg(HdmiRxSsPtr->Hdcp14Ptr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK, (u32)0xFFFFFFFFu);
+	} else if (irq == xhdmi->hdcp1x_timer_irq) {
+		XTmrCtr_DisableIntr(HdmiRxSsPtr->HdcpTimerPtr->BaseAddress, 0);
+	} else if (irq == xhdmi->hdcp22_timer_irq) {
+		XTmrCtr_DisableIntr(HdmiRxSsPtr->Hdcp22Ptr->TimerInst.BaseAddress, 0);
+		XTmrCtr_DisableIntr(HdmiRxSsPtr->Hdcp22Ptr->TimerInst.BaseAddress, 1);
+	}
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* call bottom-half */
+	return IRQ_WAKE_THREAD;
+}
+
+/* HDCP service routine, runs outside of interrupt context and can sleep and takes mutexes */
+static irqreturn_t hdmirx_hdcp_irq_thread(int irq, void *dev_id)
+{
+	struct xhdmi_device *xhdmi;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	unsigned long flags;
+	xhdmi = (struct xhdmi_device *)dev_id;
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	/* driver is being torn down, do not process further interrupts */
+	if (xhdmi->teardown) {
+		printk(KERN_INFO "irq_thread: teardown\n");
+		return IRQ_HANDLED;
+	}
+
+	/* invoke the bare-metal interrupt handler under mutex lock */
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	if (irq == xhdmi->hdcp1x_irq) {
+		XV_HdmiRxSS_HdcpIntrHandler(HdmiRxSsPtr);
+	} else if (irq == xhdmi->hdcp1x_timer_irq) {
+		XV_HdmiRxSS_HdcpTimerIntrHandler(HdmiRxSsPtr);
+	} else if (irq == xhdmi->hdcp22_timer_irq) {
+		XV_HdmiRxSS_Hdcp22TimerIntrHandler(HdmiRxSsPtr);
+	}
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+
+	/* re-enable interrupt requests */
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	if (irq == xhdmi->hdcp1x_irq) {
+		XHdcp1x_WriteReg(HdmiRxSsPtr->Hdcp14Ptr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK, (u32)0xFFFFFFFDu);
+	} else if (irq == xhdmi->hdcp1x_timer_irq) {
+		XTmrCtr_EnableIntr(HdmiRxSsPtr->HdcpTimerPtr->BaseAddress, 0);
+	} else if (irq == xhdmi->hdcp22_timer_irq) {
+		XTmrCtr_EnableIntr(HdmiRxSsPtr->Hdcp22Ptr->TimerInst.BaseAddress, 0);
+		XTmrCtr_EnableIntr(HdmiRxSsPtr->Hdcp22Ptr->TimerInst.BaseAddress, 1);
+	}
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+/* callbacks from HDMI RX SS interrupt handler
+ * these are called with the xhdmi->mutex locked and the xvphy_mutex non-locked
+ * to prevent mutex deadlock, always lock the xhdmi first, then the xvphy mutex */
+static void RxConnectCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+
+	if (!xhdmi || !HdmiRxSsPtr)
+		return;
+
+	VphyPtr = xhdmi->xvphy;
+	XGtPhyPtr = xhdmi->xgtphy;
+
+	if ((xhdmi->isvphy && !VphyPtr) || (!xhdmi->isvphy && !XGtPhyPtr))
+		return;
+
+	xhdmi->cable_is_connected = !!HdmiRxSsPtr->IsStreamConnected;
+	dev_dbg(xhdmi->dev,"RxConnectCallback(): cable is %sconnected.\n",
+					xhdmi->cable_is_connected? "": "dis");
+
+	xvphy_mutex_lock(xhdmi->phy[0]);
+	/* RX cable is connected? */
+	if (HdmiRxSsPtr->IsStreamConnected) {
+		if (xhdmi->isvphy)
+			XVphy_IBufDsEnable(VphyPtr, 0, XVPHY_DIR_RX, (TRUE));
+		else
+			XHdmiphy1_IBufDsEnable(XGtPhyPtr, 0, XHDMIPHY1_DIR_RX, (TRUE));
+	} else {
+		if (xhdmi->isvphy) {
+			/* clear GT RX TMDS clock ratio */
+			VphyPtr->HdmiRxTmdsClockRatio = 0;
+			XVphy_IBufDsEnable(VphyPtr, 0, XVPHY_DIR_RX, (FALSE));
+		} else {
+			/* clear GT RX TMDS clock ratio */
+			XGtPhyPtr->HdmiRxTmdsClockRatio = 0;
+			XHdmiphy1_IBufDsEnable(XGtPhyPtr, 0, XHDMIPHY1_DIR_RX, (FALSE));
+		}
+	}
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+}
+
+static void RxStreamDownCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+
+	if (!xhdmi || !HdmiRxSsPtr) return;
+	(void)HdmiRxSsPtr;
+	dev_dbg(xhdmi->dev,"RxStreamDownCallback()\n");
+	xhdmi->hdmi_stream_is_up = 0;
+	xhdmi->hdcp_authenticated = 0;
+}
+
+static void RxStreamInitCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+	XVidC_VideoStream *HdmiRxSsVidStreamPtr;
+	u32 Status;
+
+	if (!xhdmi || !HdmiRxSsPtr)
+		return;
+
+	VphyPtr = xhdmi->xvphy;
+	XGtPhyPtr = xhdmi->xgtphy;
+
+	if ((xhdmi->isvphy && !VphyPtr) || (!xhdmi->isvphy && !XGtPhyPtr))
+		return;
+
+	dev_dbg(xhdmi->dev,"RxStreamInitCallback\r\n");
+	// Calculate RX MMCM parameters
+	// In the application the YUV422 colordepth is 12 bits
+	// However the HDMI transports YUV422 in 8 bits.
+	// Therefore force the colordepth to 8 bits when the colorspace is YUV422
+
+	HdmiRxSsVidStreamPtr = XV_HdmiRxSs_GetVideoStream(HdmiRxSsPtr);
+
+	xvphy_mutex_lock(xhdmi->phy[0]);
+
+	if (HdmiRxSsVidStreamPtr->ColorFormatId == XVIDC_CSF_YCRCB_422) {
+		if (xhdmi->isvphy) {
+			Status = XVphy_HdmiCfgCalcMmcmParam(VphyPtr, 0, XVPHY_CHANNEL_ID_CH1,
+					XVPHY_DIR_RX,
+					HdmiRxSsVidStreamPtr->PixPerClk,
+					XVIDC_BPC_8);
+		} else {
+			Status = XHdmiphy1_HdmiCfgCalcMmcmParam(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CH1,
+					XHDMIPHY1_DIR_RX,
+					HdmiRxSsVidStreamPtr->PixPerClk,
+					XVIDC_BPC_8);
+		}
+	// Other colorspaces
+	} else {
+		if (xhdmi->isvphy) {
+			Status = XVphy_HdmiCfgCalcMmcmParam(VphyPtr, 0, XVPHY_CHANNEL_ID_CH1,
+					XVPHY_DIR_RX,
+					HdmiRxSsVidStreamPtr->PixPerClk,
+					HdmiRxSsVidStreamPtr->ColorDepth);
+		} else {
+			Status = XHdmiphy1_HdmiCfgCalcMmcmParam(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CH1,
+					XHDMIPHY1_DIR_RX,
+					HdmiRxSsVidStreamPtr->PixPerClk,
+					HdmiRxSsVidStreamPtr->ColorDepth);
+		}
+	}
+
+	if (Status == XST_FAILURE) {
+		xvphy_mutex_unlock(xhdmi->phy[0]);
+		return;
+	}
+
+	// Enable and configure RX MMCM
+	if (xhdmi->isvphy)
+		XVphy_MmcmStart(VphyPtr, 0, XVPHY_DIR_RX);
+	else
+		XHdmiphy1_MmcmStart(XGtPhyPtr, 0, XHDMIPHY1_DIR_RX);
+	//wait 10ms for PLL to stabilize
+	usleep_range(10000, 11000);
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+}
+
+/*
+ * Duplicate of v4l2_hdmi_rx_colorimetry to fit xilinx hdmi structure
+ * definition. Ideally we could use the API directly, but limited by the AVI
+ * infoframe definition as it is only for AVI version 2 only. In future extend
+ * the framework to handle higher AVI infoframe version and use the
+ * structures/APIs directly from framework.
+ *
+ * By default, an SD Video Format shall be encoded according to SMPTE 170M [1]
+ * color space, an HD Video Format shall be encoded according to ITU-R BT.709
+ * [7] color space.
+ */
+
+void hdmirx_getformat(struct xhdmi_device *xhdmi,
+		XV_HdmiRxSs *HdmiRxSsPtr,
+		XVidC_VideoStream *Stream)
+{
+	XHdmiC_AVI_InfoFrame *avi =
+		XV_HdmiRxSs_GetAviInfoframe(HdmiRxSsPtr);
+
+	XHdmiC_VSIF *vsif = XV_HdmiRxSs_GetVSIF(HdmiRxSsPtr);
+	bool default_is_lim_range_rgb = avi->VIC > 1;
+	bool is_ce = avi->VIC || (vsif && vsif->HDMI_VIC);
+	bool is_sdtv = (xhdmi->detected_format.height) <= 576;
+	xhdmi->detected_format.colorspace = V4L2_COLORSPACE_DEFAULT;
+	xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_DEFAULT;
+	xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+	xhdmi->detected_format.quantization = V4L2_QUANTIZATION_DEFAULT;
+
+	switch (avi->ColorSpace) {
+	case HDMI_COLORSPACE_RGB:
+		/* RGB pixel encoding */
+		switch (avi->Colorimetry) {
+		case HDMI_COLORIMETRY_EXTENDED:
+			switch (avi->ExtendedColorimetry) {
+			case HDMI_EXTENDED_COLORIMETRY_OPRGB:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_OPRGB;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_OPRGB;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_601;
+				break;
+			case HDMI_EXTENDED_COLORIMETRY_BT2020:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_BT2020;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_BT2020;
+				break;
+			default:
+				break;
+			}
+			break;
+		default:
+			break;
+		}
+
+		switch (avi->QuantizationRange) {
+		case HDMI_QUANTIZATION_RANGE_LIMITED:
+			xhdmi->detected_format.quantization = V4L2_QUANTIZATION_LIM_RANGE;
+			break;
+		case HDMI_QUANTIZATION_RANGE_FULL:
+			break;
+		default:
+			if (default_is_lim_range_rgb)
+				xhdmi->detected_format.quantization = V4L2_QUANTIZATION_LIM_RANGE;
+			break;
+		}
+		break;
+
+	default:
+		/* YCbCr pixel encoding */
+		switch (avi->YccQuantizationRange) {
+		case HDMI_YCC_QUANTIZATION_RANGE_FULL:
+			xhdmi->detected_format.quantization = V4L2_QUANTIZATION_FULL_RANGE;
+			break;
+		default:
+			xhdmi->detected_format.quantization = V4L2_QUANTIZATION_LIM_RANGE;
+			break;
+		}
+		/*
+		 * TODO: Add based on color components. Refer 14 of CTA-861-G
+		 * specification
+		 */
+		switch (avi->Colorimetry) {
+		case HDMI_COLORIMETRY_NONE:
+			if (!is_ce)
+				break;
+			if (is_sdtv) {
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_SMPTE170M;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_601;
+			} else {
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_REC709;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_709;
+			}
+			xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+			break;
+		case HDMI_COLORIMETRY_ITU_601:
+			xhdmi->detected_format.colorspace = V4L2_COLORSPACE_SMPTE170M;
+			xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_601;
+			xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+			break;
+		case HDMI_COLORIMETRY_ITU_709:
+			xhdmi->detected_format.colorspace = V4L2_COLORSPACE_REC709;
+			xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_709;
+			xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+			break;
+		case HDMI_COLORIMETRY_EXTENDED:
+			switch (avi->ExtendedColorimetry) {
+			case HDMI_EXTENDED_COLORIMETRY_XV_YCC_601:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_REC709;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_XV709;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+				break;
+			case HDMI_EXTENDED_COLORIMETRY_XV_YCC_709:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_REC709;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_XV601;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+				break;
+			case HDMI_EXTENDED_COLORIMETRY_S_YCC_601:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_SRGB;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_601;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_SRGB;
+				break;
+			case HDMI_EXTENDED_COLORIMETRY_OPYCC_601:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_OPRGB;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_601;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_OPRGB;
+				break;
+			case HDMI_EXTENDED_COLORIMETRY_BT2020:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_BT2020;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_BT2020;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+				break;
+			case HDMI_EXTENDED_COLORIMETRY_BT2020_CONST_LUM:
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_BT2020;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_BT2020_CONST_LUM;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+				break;
+			default: /* fall back to ITU_709 */
+				xhdmi->detected_format.colorspace = V4L2_COLORSPACE_REC709;
+				xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_709;
+				xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_709;
+				break;
+			}
+			break;
+		default:
+			break;
+		}
+		break;
+	}
+
+	dev_dbg(xhdmi->dev,"colorspace = %d, xfer_func =%d, \
+			ycbcr_enc = %d, quantization = %d\n",
+			xhdmi->detected_format.colorspace,
+			xhdmi->detected_format.xfer_func,
+			xhdmi->detected_format.ycbcr_enc,
+			xhdmi->detected_format.quantization);
+}
+
+/* @TODO Once this upstream V4L2 patch lands, consider VIC support: https://patchwork.linuxtv.org/patch/37137/ */
+static void RxStreamUpCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	XVidC_VideoStream *Stream;
+
+	if (!xhdmi || !HdmiRxSsPtr || !HdmiRxSsPtr->HdmiRxPtr) return;
+	dev_dbg(xhdmi->dev,"RxStreamUpCallback() - stream is up.\n");
+	Stream = XV_HdmiRxSs_GetVideoStream(HdmiRxSsPtr);
+#ifdef DEBUG
+	XV_HdmiRx_DebugInfo(HdmiRxSsPtr->HdmiRxPtr);
+#endif
+	/* http://lxr.free-electrons.com/source/include/uapi/linux/videodev2.h#L1229 */
+	xhdmi->detected_format.width = Stream->Timing.HActive;
+	xhdmi->detected_format.height = Stream->Timing.VActive;
+
+	/* Check for the NTSC and PAL resolutions. RX will detect the resolution as 1440x240 (NTSC resolution)
+	 * for field 0 and field 1.
+	 * Upon detecting this RX should drop the extra pixel and send only 720x240 per field to Frame buffer write IP.
+	 * Therefore in the end of this function, we will have to call API to configure bridge for pixel drop.
+	 */
+	if((((Stream->Timing.HActive == 1440) && (Stream->Timing.VActive == 240) && (Stream->FrameRate == 60)) ||
+			((Stream->Timing.HActive == 1440) && (Stream->Timing.VActive == 288) && (Stream->FrameRate == 50)))
+			&& (!!Stream->IsInterlaced))
+	{
+		xhdmi->detected_format.width /= 2;
+		dev_dbg(xhdmi->dev, "NTSC/PAL detected_format.width after divide by 2 = %d\n", xhdmi->detected_format.width);
+	}
+
+	/* There is no point in setting feild V4L2_FIELD_INTERLACED as it is not getting used */
+	//xhdmi->detected_format.field = Stream->IsInterlaced? V4L2_FIELD_INTERLACED: V4L2_FIELD_NONE;
+	xhdmi->detected_format.field = V4L2_FIELD_NONE;
+
+	/* https://linuxtv.org/downloads/v4l-dvb-apis/ch02s05.html#v4l2-colorspace */
+	hdmirx_getformat(xhdmi, HdmiRxSsPtr, Stream);
+
+	/* https://linuxtv.org/downloads/v4l-dvb-apis/subdev.html#v4l2-mbus-framefmt */
+	/* see UG934 page 8 */
+	/* the V4L2 media bus fmt codes match the AXI S format, and match those from TPG */
+	if (Stream->ColorFormatId == XVIDC_CSF_RGB) {
+		if (HdmiRxSsPtr->Config.MaxBitsPerPixel == 10) {
+			if(Stream->ColorDepth == XVIDC_BPC_8) {
+				xhdmi->detected_format.code = MEDIA_BUS_FMT_RBG888_1X24;
+				dev_dbg(xhdmi->dev,"XVIDC_CSF_RGB -> MEDIA_BUS_FMT_RBG888_1X24\n");
+			} else {
+				xhdmi->detected_format.code = MEDIA_BUS_FMT_RBG101010_1X30;
+				dev_dbg(xhdmi->dev,"XVIDC_CSF_RGB -> MEDIA_BUS_FMT_RBG101010_1X30\n");
+			}
+		/* Default will always be 8 */
+		} else {
+			xhdmi->detected_format.code = MEDIA_BUS_FMT_RBG888_1X24;
+			dev_dbg(xhdmi->dev,"XVIDC_CSF_RGB -> MEDIA_BUS_FMT_RBG888_1X24\n");
+		}
+
+	/* YUV444 */
+	} else if (Stream->ColorFormatId == XVIDC_CSF_YCRCB_444) {
+		if (HdmiRxSsPtr->Config.MaxBitsPerPixel == 10) {
+			if(Stream->ColorDepth == XVIDC_BPC_8) {
+				xhdmi->detected_format.code = MEDIA_BUS_FMT_VUY8_1X24;
+				dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_444 -> MEDIA_BUS_FMT_VUY8_1X24\n");
+			} else {
+				xhdmi->detected_format.code = MEDIA_BUS_FMT_VUY10_1X30;
+				dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_444 -> MEDIA_BUS_FMT_VUY10_1X30\n");
+			}
+		/* Default will always be 8 */
+		} else {
+			xhdmi->detected_format.code = MEDIA_BUS_FMT_VUY8_1X24;
+			dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_444 -> MEDIA_BUS_FMT_VUY8_1X24\n");
+		}
+
+	/* Since 422 is always detected as 12 BPC, set the 8bit media bus format */
+	} else if (Stream->ColorFormatId == XVIDC_CSF_YCRCB_422) {
+		if (HdmiRxSsPtr->Config.MaxBitsPerPixel == 10) {
+			xhdmi->detected_format.code = MEDIA_BUS_FMT_UYVY10_1X20;
+			dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_422 -> MEDIA_BUS_FMT_UYVY10_1X20\n");
+		/* Default will always be 8 */
+		} else {
+			xhdmi->detected_format.code = MEDIA_BUS_FMT_UYVY8_1X16;
+			dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_422 -> MEDIA_BUS_FMT_UYVY8_1X16\n");
+		}
+
+	/* YUV420 */
+	} else if (Stream->ColorFormatId == XVIDC_CSF_YCRCB_420) {
+		if (HdmiRxSsPtr->Config.MaxBitsPerPixel == 10) {
+			if(Stream->ColorDepth == XVIDC_BPC_8) {
+				xhdmi->detected_format.code = MEDIA_BUS_FMT_VYYUYY8_1X24;
+				dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_420 -> MEDIA_BUS_FMT_VYYUYY8_1X24\n");
+			} else {
+				xhdmi->detected_format.code = MEDIA_BUS_FMT_VYYUYY10_4X20;
+				dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_420 -> MEDIA_BUS_FMT_VYYUYY10_1X24\n");
+			}
+		} else {
+			xhdmi->detected_format.code = MEDIA_BUS_FMT_VYYUYY8_1X24;
+			dev_dbg(xhdmi->dev,"XVIDC_CSF_YCRCB_420 -> MEDIA_BUS_FMT_VYYUYY8_1X24\n");
+		}
+	}
+
+	/* map to v4l2_dv_timings */
+	xhdmi->detected_timings.type =  V4L2_DV_BT_656_1120;
+
+	/* Read Active Pixels */
+	xhdmi->detected_timings.bt.width = Stream->Timing.HActive;
+	/* Active lines field 1 */
+	xhdmi->detected_timings.bt.height = Stream->Timing.VActive;
+	/* Interlaced */
+	xhdmi->detected_timings.bt.interlaced = !!Stream->IsInterlaced;
+	xhdmi->detected_timings.bt.polarities =
+	/* Vsync polarity, Positive == 1 */
+		(Stream->Timing.VSyncPolarity? V4L2_DV_VSYNC_POS_POL: 0) |
+	/* Hsync polarity, Positive == 1 */
+		(Stream->Timing.HSyncPolarity? V4L2_DV_HSYNC_POS_POL: 0);
+
+	/* from xvid.c:XVidC_GetPixelClockHzByVmId() but without VmId */
+	if (Stream->IsInterlaced) {
+		xhdmi->detected_timings.bt.pixelclock =
+			(Stream->Timing.F0PVTotal + Stream->Timing.F1VTotal) *
+			Stream->FrameRate / 2;
+	} else {
+		xhdmi->detected_timings.bt.pixelclock =
+			Stream->Timing.F0PVTotal * Stream->FrameRate;
+	}
+	xhdmi->detected_timings.bt.pixelclock *= Stream->Timing.HTotal;
+
+	/* Check for the NTSC and PAL resolutions. RX will detect the resolution as 1440x240 (NTSC resolution)
+	 * for field 0 and field 1.
+	 * Upon detecting this RX should drop the extra pixel and send only 720x240 per field to Frame buffer write IP.
+	 * Therefore in the end of this function, we will have to call API to configure bridge for pixel drop.
+	 */
+	if((((Stream->Timing.HActive == 1440) && (Stream->Timing.VActive == 240) && (Stream->FrameRate == 60)) ||
+			((Stream->Timing.HActive == 1440) && (Stream->Timing.VActive == 288) && (Stream->FrameRate == 50)))
+			&& (!!Stream->IsInterlaced))
+	{
+		xhdmi->detected_timings.bt.width /= 2;
+		dev_dbg(xhdmi->dev, "NTSC/PAL detected_timings.bt.width after divide by 2 = %d\n", xhdmi->detected_format.width);
+
+		dev_dbg(xhdmi->dev,"Programming RX bridge for dropping pixels\n");
+		XV_HdmiRxSs_BridgeYuv420(HdmiRxSsPtr, FALSE);
+		XV_HdmiRxSs_BridgePixelDrop(HdmiRxSsPtr, TRUE);
+	}
+
+	dev_dbg(xhdmi->dev,"HdmiRxSsPtr->HdmiRxPtr->Stream.PixelClk = %d\n", HdmiRxSsPtr->HdmiRxPtr->Stream.PixelClk);
+	/* Read HFront Porch */
+	xhdmi->detected_timings.bt.hfrontporch = Stream->Timing.HFrontPorch;
+	/* Read Hsync Width */
+	xhdmi->detected_timings.bt.hsync = Stream->Timing.HSyncWidth;
+	/* Read HBack Porch */
+	xhdmi->detected_timings.bt.hbackporch = Stream->Timing.HBackPorch;
+	/* Read VFront Porch field 1*/
+	xhdmi->detected_timings.bt.vfrontporch = Stream->Timing.F0PVFrontPorch;
+	/* Read VSync Width field 1*/
+	xhdmi->detected_timings.bt.vsync = Stream->Timing.F0PVSyncWidth;
+	/* Read VBack Porch field 1 */
+	xhdmi->detected_timings.bt.vbackporch = Stream->Timing.F0PVBackPorch;
+	/* Read VFront Porch field 2*/
+	xhdmi->detected_timings.bt.il_vfrontporch = Stream->Timing.F1VFrontPorch;
+	/* Read VSync Width field 2*/
+	xhdmi->detected_timings.bt.il_vsync = Stream->Timing.F1VSyncWidth;
+	/* Read VBack Porch field 2 */
+	xhdmi->detected_timings.bt.il_vbackporch = Stream->Timing.F1VBackPorch;
+	xhdmi->detected_timings.bt.standards = V4L2_DV_BT_STD_CEA861;
+	xhdmi->detected_timings.bt.flags = V4L2_DV_FL_IS_CE_VIDEO;
+
+	(void)Stream->VmId;
+
+	xhdmi->hdmi_stream_is_up = 1;
+	/* notify source format change event */
+	v4l2_subdev_notify_event(&xhdmi->subdev, &xhdmi_ev_fmt);
+
+	/* TODO: As subsystem API XV_HdmiRxSs_AudioEnable is not available,
+	 *  core API is used currently.
+	 */
+	if (xhdmi->audio_init)
+		XV_HdmiRx_AudioEnable(HdmiRxSsPtr->HdmiRxPtr);
+#ifdef DEBUG
+	v4l2_print_dv_timings("xilinx-hdmi-rx", "", & xhdmi->detected_timings, 1);
+#endif
+}
+
+static void RxBrdgOverflowCallback(void *CallbackRef)
+{
+	//dev_dbg(xhdmi->dev,"RxBrdgOverflowCallback()\n");
+}
+
+static void RxAudCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	struct xlnx_hdmirx_audio_data *adata = xhdmi->rx_audio_data;
+
+	dev_dbg(xhdmi->dev,"%s()\n", __func__);
+	adata->format = XV_HdmiRxSs_GetAudioFormat(HdmiRxSsPtr);
+	adata->num_channels = XV_HdmiRxSs_GetAudioChannels(HdmiRxSsPtr);
+	//ToDo: Insert registered ALSA driver call-back
+	if (xhdmi->audio_init && adata->num_channels >= 2) {
+		adata->audio_detected = true;
+		wake_up_interruptible(&adata->audio_update_q);
+	}
+
+	dev_dbg(xhdmi->dev, "Channels = %d\n", adata->num_channels);
+	dev_dbg(xhdmi->dev, "Format   = %d\n", adata->format);
+}
+
+static void RxAuxCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	XHdmiC_Aux *AuxPtr;
+	XHdmiC_Aux AuxFifo;
+	bool AviInfoFrameChangeStatus = false;
+	unsigned long flags;
+
+	AuxPtr = XV_HdmiRxSs_GetAuxiliary(HdmiRxSsPtr);
+
+	//dev_dbg(xhdmi->dev,"%s()\n", __func__);
+	/* read out the aux packet to a local buffer
+	 *  currently only 1 Aux packet (last recvd) is stored
+	 */
+	if (AuxPtr->Header.Byte[0] != AUX_GENERAL_CONTROL_PACKET_TYPE) {
+		memcpy(&AuxFifo, AuxPtr, sizeof(XHdmiC_Aux));
+	}
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	AviInfoFrameChangeStatus = IsAVIInfoFrameChanged(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	if (AviInfoFrameChangeStatus &&
+			XV_HdmiRxSs_IsStreamUp(HdmiRxSsPtr)) {
+		RxStreamUpCallback(CallbackRef);
+	}
+	//ToDO: Insert registered ALSA driver callback
+}
+
+/* Called from non-interrupt context with xvphy mutex locked
+ */
+static void VphyHdmiRxInitCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+
+	if (!xhdmi)
+		return;
+
+	VphyPtr = xhdmi->xvphy;
+	XGtPhyPtr = xhdmi->xgtphy;
+
+	if ((xhdmi->isvphy && !VphyPtr) || (!xhdmi->isvphy && !XGtPhyPtr))
+		return;
+
+	dev_dbg(xhdmi->dev,"VphyHdmiRxInitCallback()\n");
+
+	/* a pair of mutexes must be locked in fixed order to prevent deadlock,
+	 * and the order is RX SS then XVPHY, so first unlock XVPHY then lock both */
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	xvphy_mutex_lock(xhdmi->phy[0]);
+
+	XV_HdmiRxSs_RefClockChangeInit(HdmiRxSsPtr);
+	/* @NOTE maybe implement xvphy_set_hdmirx_tmds_clockratio(); */
+	if (xhdmi->isvphy)
+		VphyPtr->HdmiRxTmdsClockRatio = HdmiRxSsPtr->TMDSClockRatio;
+	else
+		XGtPhyPtr->HdmiRxTmdsClockRatio = HdmiRxSsPtr->TMDSClockRatio;
+
+	/* unlock RX SS but keep XVPHY locked */
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+}
+
+/* Called from non-interrupt context with xvphy mutex locked
+ */
+static void VphyHdmiRxReadyCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XVphy *VphyPtr;
+	XVphy_PllType RxPllType;
+	XHdmiphy1 *XGtPhyPtr;
+	XHdmiphy1_PllType GtRxPllType;
+
+	if (!xhdmi)
+		return;
+
+	VphyPtr = xhdmi->xvphy;
+	XGtPhyPtr = xhdmi->xgtphy;
+
+	if ((xhdmi->isvphy && !VphyPtr) || (!xhdmi->isvphy && !XGtPhyPtr))
+		return;
+
+	dev_dbg(xhdmi->dev,"VphyHdmiRxReadyCallback()\n");
+
+	/* a pair of mutexes must be locked in fixed order to prevent deadlock,
+	 * and the order is RX SS then XVPHY, so first unlock XVPHY then lock both */
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	xvphy_mutex_lock(xhdmi->phy[0]);
+
+	if (xhdmi->isvphy) {
+		RxPllType = XVphy_GetPllType(VphyPtr, 0, XVPHY_DIR_RX,
+			XVPHY_CHANNEL_ID_CH1);
+		if (!(RxPllType == XVPHY_PLL_TYPE_CPLL)) {
+			XV_HdmiRxSs_SetStream(&xhdmi->xv_hdmirxss, VphyPtr->HdmiRxRefClkHz,
+					(XVphy_GetLineRateHz(VphyPtr, 0, XVPHY_CHANNEL_ID_CMN0)/1000000));
+		}
+		else {
+			XV_HdmiRxSs_SetStream(&xhdmi->xv_hdmirxss, VphyPtr->HdmiRxRefClkHz,
+					(XVphy_GetLineRateHz(VphyPtr, 0, XVPHY_CHANNEL_ID_CH1)/1000000));
+		}
+	} else {
+		GtRxPllType = XHdmiphy1_GetPllType(XGtPhyPtr, 0, XHDMIPHY1_DIR_RX,
+			XHDMIPHY1_CHANNEL_ID_CH1);
+		if (!(GtRxPllType == XHDMIPHY1_PLL_TYPE_CPLL)) {
+			XV_HdmiRxSs_SetStream(&xhdmi->xv_hdmirxss, XGtPhyPtr->HdmiRxRefClkHz,
+				(XHdmiphy1_GetLineRateHz(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CMN0)/1000000));
+		} else {
+			XV_HdmiRxSs_SetStream(&xhdmi->xv_hdmirxss, XGtPhyPtr->HdmiRxRefClkHz,
+				(XHdmiphy1_GetLineRateHz(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CH1)/1000000));
+		}
+	}
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+}
+
+static void RxHdcpAuthenticatedCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	int HdcpProtocol;
+
+	HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	HdcpProtocol = XV_HdmiRxSs_HdcpGetProtocol(HdmiRxSsPtr);
+	xhdmi->hdcp_authenticated = 1;
+	switch (HdcpProtocol) {
+	case XV_HDMIRXSS_HDCP_22:
+		dev_dbg(xhdmi->dev,"HDCP 2.2 RX authenticated.\n");
+		break;
+	case XV_HDMIRXSS_HDCP_14:
+		dev_dbg(xhdmi->dev,"HDCP 1.4 RX authenticated.\n");
+		break;
+	}
+}
+
+static void RxHdcpUnauthenticatedCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+
+	xhdmi->hdcp_authenticated = 0;
+	dev_dbg(xhdmi->dev,"HDCP RX unauthenticated.\n");
+}
+
+static void RxHdcpEncryptionUpdateCallback(void *CallbackRef)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)CallbackRef;
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+
+	xhdmi->hdcp_encrypted = !!XV_HdmiRxSs_HdcpIsEncrypted(HdmiRxSsPtr);
+	dev_dbg(xhdmi->dev,"HDCP RX encryption changed; now %s.\n",
+					xhdmi->hdcp_encrypted? "enabled": "disabled");
+}
+
+/* this function is responsible for periodically calling XV_HdmiRxSs_HdcpPoll() */
+static void hdcp_poll_work(struct work_struct *work)
+{
+	/* find our parent container structure */
+	struct xhdmi_device *xhdmi = container_of(work, struct xhdmi_device,
+		delayed_work_hdcp_poll.work);
+
+	XV_HdmiRxSs *HdmiRxSsPtr;
+
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	XV_HdmiRxSs_HdcpPoll(HdmiRxSsPtr);
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+	/* reschedule this work again in 1 millisecond */
+	schedule_delayed_work(&xhdmi->delayed_work_hdcp_poll, msecs_to_jiffies(1));
+	return;
+}
+
+static int XHdcp_KeyManagerInit(uintptr_t BaseAddress, u8 *Hdcp14Key)
+{
+	u32 RegValue;
+	u8 Row;
+	u8 i;
+	u8 *KeyPtr;
+	u8 Status;
+
+	/* Assign key pointer */
+	KeyPtr = Hdcp14Key;
+
+	/* Reset */
+	Xil_Out32((BaseAddress + 0x0c), (1<<31));
+
+	// There are 41 rows
+	for (Row=0; Row<41; Row++)
+	{
+		/* Set write enable */
+		Xil_Out32((BaseAddress + 0x20), 1);
+
+		/* High data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		/* Write high data */
+		Xil_Out32((BaseAddress + 0x2c), RegValue);
+
+		/* Low data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		/* Write low data */
+		Xil_Out32((BaseAddress + 0x30), RegValue);
+
+		/* Table / Row Address */
+		Xil_Out32((BaseAddress + 0x28), Row);
+
+		// Write in progress
+		do
+		{
+			RegValue = Xil_In32(BaseAddress + 0x24);
+			RegValue &= 1;
+		} while (RegValue != 0);
+	}
+
+	// Verify
+
+	/* Re-Assign key pointer */
+	KeyPtr = Hdcp14Key;
+
+	/* Default Status */
+	Status = XST_SUCCESS;
+
+	/* Start at row 0 */
+	Row = 0;
+
+	do
+	{
+		/* Set read enable */
+		Xil_Out32((BaseAddress + 0x20), (1<<1));
+
+		/* Table / Row Address */
+		Xil_Out32((BaseAddress + 0x28), Row);
+
+		// Read in progress
+		do
+		{
+			RegValue = Xil_In32(BaseAddress + 0x24);
+			RegValue &= 1;
+		} while (RegValue != 0);
+
+		/* High data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		if (RegValue != Xil_In32(BaseAddress + 0x2c))
+			Status = XST_FAILURE;
+
+		/* Low data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		if (RegValue != Xil_In32(BaseAddress + 0x30))
+			Status = XST_FAILURE;
+
+		/* Increment row */
+		Row++;
+
+	} while ((Row<41) && (Status == XST_SUCCESS));
+
+	if (Status == XST_SUCCESS)
+	{
+		/* Set read lockout */
+		Xil_Out32((BaseAddress + 0x20), (1<<31));
+
+		/* Start AXI-Stream */
+		Xil_Out32((BaseAddress + 0x0c), (1));
+	}
+
+	return Status;
+}
+
+
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+static int instance = 0;
+/* TX uses [1, 127] and RX uses [128, 254] */
+/* The HDCP22 timer uses an additional offset of +64 */
+#define RX_DEVICE_ID_BASE 128
+
+/* Local Global table for sub-core instance(s) configuration settings */
+XV_HdmiRx_Config XV_HdmiRx_ConfigTable[XPAR_XV_HDMIRX_NUM_INSTANCES];
+
+extern XHdcp22_Cipher_Config XHdcp22_Cipher_ConfigTable[];
+extern XHdcp22_Rng_Config XHdcp22_Rng_ConfigTable[];
+extern XHdcp22_mmult_Config XHdcp22_mmult_ConfigTable[];
+extern XHdcp1x_Config XHdcp1x_ConfigTable[];
+extern XTmrCtr_Config XTmrCtr_ConfigTable[];
+extern XHdcp22_Rx_Config XHdcp22_Rx_ConfigTable[];
+
+/* Compute the absolute address by adding subsystem base address
+   to sub-core offset */
+static int xhdmi_subcore_AbsAddr(uintptr_t SubSys_BaseAddr,
+                                 uintptr_t SubSys_HighAddr,
+								 uintptr_t SubCore_Offset,
+								 uintptr_t *SubCore_AbsAddr)
+{
+  int Status;
+  uintptr_t absAddr;
+
+  absAddr = SubSys_BaseAddr | SubCore_Offset;
+  if((absAddr>=SubSys_BaseAddr) && (absAddr<=SubSys_HighAddr)) {
+    *SubCore_AbsAddr = absAddr;
+    Status = XST_SUCCESS;
+  } else {
+    *SubCore_AbsAddr = 0;
+    Status = XST_FAILURE;
+  }
+
+  return(Status);
+}
+
+/* Each sub-core within the subsystem has defined offset read from
+   device-tree. */
+static int xhdmi_compute_subcore_AbsAddr(XV_HdmiRxSs_Config *config)
+{
+	int ret;
+
+	/* Subcore: Rx */
+	ret = xhdmi_subcore_AbsAddr(config->BaseAddress,
+							    config->HighAddress,
+							    config->HdmiRx.AbsAddr,
+							    &(config->HdmiRx.AbsAddr));
+	if (ret != XST_SUCCESS) {
+	   return -EFAULT;
+	}
+	XV_HdmiRx_ConfigTable[instance].BaseAddress = config->HdmiRx.AbsAddr;
+
+	/* Subcore: hdcp1x */
+	if (config->Hdcp14.IsPresent) {
+		ret = xhdmi_subcore_AbsAddr(config->BaseAddress,
+									config->HighAddress,
+									config->Hdcp14.AbsAddr,
+									&(config->Hdcp14.AbsAddr));
+	  if (ret != XST_SUCCESS) {
+	     return -EFAULT;
+	  }
+	  XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES/2 + instance].BaseAddress = config->Hdcp14.AbsAddr;
+    }
+
+	/* Subcore: hdcp1x timer */
+	if (config->HdcpTimer.IsPresent) {
+	  ret = xhdmi_subcore_AbsAddr(config->BaseAddress,
+	  						      config->HighAddress,
+	  						      config->HdcpTimer.AbsAddr,
+	  						      &(config->HdcpTimer.AbsAddr));
+	  if (ret != XST_SUCCESS) {
+	     return -EFAULT;
+	  }
+	  XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 0].BaseAddress = config->HdcpTimer.AbsAddr;
+    }
+
+	/* Subcore: hdcp22 */
+	if (config->Hdcp22.IsPresent) {
+	  ret = xhdmi_subcore_AbsAddr(config->BaseAddress,
+	  						      config->HighAddress,
+	  						      config->Hdcp22.AbsAddr,
+	  						      &(config->Hdcp22.AbsAddr));
+	  if (ret != XST_SUCCESS) {
+	     return -EFAULT;
+	  }
+	  XHdcp22_Rx_ConfigTable[instance].BaseAddress = config->Hdcp22.AbsAddr;
+	}
+
+	return (ret);
+}
+
+static ssize_t vphy_log_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+	XVphy *VphyPtr = xhdmi->xvphy;
+	XHdmiphy1 *XGtPhyPtr = xhdmi->xgtphy;
+
+	if (xhdmi->isvphy)
+		count = XVphy_LogShow(VphyPtr, buf, PAGE_SIZE);
+	else
+		count = XHdmiphy1_LogShow(XGtPhyPtr, buf, PAGE_SIZE);
+
+	return count;
+}
+
+static ssize_t vphy_info_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	if (xhdmi->isvphy) {
+		VphyPtr = xhdmi->xvphy;
+		count = XVphy_HdmiDebugInfo(VphyPtr, 0, XVPHY_CHANNEL_ID_CHA, buf, PAGE_SIZE);
+		count += scnprintf(&buf[count], (PAGE_SIZE-count), "Rx Ref Clk: %0d Hz\n",
+					XVphy_ClkDetGetRefClkFreqHz(xhdmi->xvphy, XVPHY_DIR_RX));
+		count += scnprintf(&buf[count], (PAGE_SIZE-count), "DRU Ref Clk: %0d Hz\n",
+					XVphy_DruGetRefClkFreqHz(xhdmi->xvphy));
+	} else {
+		XGtPhyPtr = xhdmi->xgtphy;
+		count = XHdmiphy1_HdmiDebugInfo(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CHA, buf, PAGE_SIZE);
+		count += scnprintf(&buf[count], (PAGE_SIZE-count), "Rx Ref Clk: %0d Hz\n",
+					XHdmiphy1_ClkDetGetRefClkFreqHz(xhdmi->xgtphy, XHDMIPHY1_DIR_RX));
+		count += scnprintf(&buf[count], (PAGE_SIZE-count), "DRU Ref Clk: %0d Hz\n",
+					XHdmiphy1_DruGetRefClkFreqHz(xhdmi->xgtphy));
+	}
+	return count;
+}
+
+static ssize_t hdmi_log_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	count = XV_HdmiRxSs_LogShow(HdmiRxSsPtr, buf, PAGE_SIZE);
+	return count;
+}
+
+static ssize_t hdcp_log_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	count = XV_HdmiRxSs_HdcpInfo(HdmiRxSsPtr, buf, PAGE_SIZE);
+	return count;
+}
+
+static ssize_t hdmi_info_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	count = 0;
+	if (XV_HdmiRxSs_IsStreamUp(HdmiRxSsPtr)) {
+		count = XVidC_ShowStreamInfo(&HdmiRxSsPtr->HdmiRxPtr->Stream.Video, buf, PAGE_SIZE);
+	}
+	count += XV_HdmiRxSs_ShowInfo(HdmiRxSsPtr, &buf[count], (PAGE_SIZE-count));
+	return count;
+}
+
+static ssize_t hdcp_debugen_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	long int i;
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	if (kstrtol(buf, 10, &i)) {
+		printk(KERN_INFO "hdcp_debugen_store() input invalid.\n");
+		return count;
+	}
+	i = !!i;
+	if (i) {
+		/* Enable detail logs for hdcp transactions*/
+		XV_HdmiRxSs_HdcpSetInfoDetail(HdmiRxSsPtr, TRUE);
+	} else {
+		/* Disable detail logs for hdcp transactions*/
+		XV_HdmiRxSs_HdcpSetInfoDetail(HdmiRxSsPtr, FALSE);
+	}
+	return count;
+}
+
+static ssize_t hdcp_authenticated_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_authenticated);
+	return count;
+}
+
+static ssize_t hdcp_encrypted_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_encrypted);
+	return count;
+}
+
+/* This function decrypts the HDCP keys, uses aes256.c */
+/* Note that the bare-metal implementation deciphers in-place in the cipherbuffer, then after that copies to the plaintext buffer,
+ * thus trashing the source.
+ *
+ * In this implementation, a local buffer is created (aligned to 16Byte boundary), the cipher is first copied to the local buffer,
+ * where it is then decrypted in-place and then copied over to target Plain Buffer. This leaves the source buffer intact.
+ */
+static void Decrypt(const u8 *CipherBufferPtr/*src*/, u8 *PlainBufferPtr/*dst*/, u8 *Key, u16 Length)
+{
+	u16 i;
+	u8 *AesBufferPtr;
+	u8 *LocalBuf; //16Byte aligned
+	u16 AesLength;
+	aes256_context ctx;
+
+	AesLength = Length/16; // The aes always encrypts 16 bytes
+	if (Length % 16) {
+		AesLength++;
+	}
+
+	//Allocate local buffer that is 16Byte aligned
+	LocalBuf = kzalloc((size_t)(AesLength*16), GFP_KERNEL);
+	if (!LocalBuf) {
+		printk(KERN_ERR "%s - %s Unable to allocate memory!\n",
+		       __FILE__, __func__);
+		return;
+	}
+
+	// Copy cipher into local buffer
+	memcpy(LocalBuf, CipherBufferPtr, (AesLength*16));
+
+	// Assign local Pointer // @NOTE: Changed
+	AesBufferPtr = LocalBuf;
+
+	// Initialize AES256
+	aes256_init(&ctx, Key);
+
+	for (i=0; i<AesLength; i++)
+	{
+		// Decrypt
+		aes256_decrypt_ecb(&ctx, AesBufferPtr);
+
+		// Increment pointer
+		AesBufferPtr += 16;	// The aes always encrypts 16 bytes
+	}
+
+	// Done
+	aes256_done(&ctx);
+
+	//copy decrypted key into Plainbuffer
+	memcpy(PlainBufferPtr, LocalBuf, Length);
+
+	//free local buffer
+	kfree(LocalBuf);
+}
+
+#define SIGNATURE_OFFSET			0
+#define HDCP22_LC128_OFFSET			16
+#define HDCP22_CERTIFICATE_OFFSET	32
+#define HDCP14_KEY1_OFFSET			1024
+#define HDCP14_KEY2_OFFSET			1536
+
+/* buffer points to the encrypted data (from EEPROM), password points to a 32-character password */
+static int XHdcp_LoadKeys(const u8 *Buffer, u8 *Password, u8 *Hdcp22Lc128, u32 Hdcp22Lc128Size, u8 *Hdcp22RxPrivateKey, u32 Hdcp22RxPrivateKeySize,
+	u8 *Hdcp14KeyA, u32 Hdcp14KeyASize, u8 *Hdcp14KeyB, u32 Hdcp14KeyBSize)
+{
+	u8 i;
+	const u8 HdcpSignature[16] = { "xilinx_hdcp_keys" };
+	u8 Key[32] = { 0 };
+	u8 SignatureOk;
+	u8 HdcpSignatureBuffer[16];
+
+	// Generate password hash
+	XHdcp22Cmn_Sha256Hash(Password, 32, Key);
+
+	/* decrypt the signature */
+	Decrypt(&Buffer[SIGNATURE_OFFSET]/*source*/, HdcpSignatureBuffer/*destination*/, Key, sizeof(HdcpSignature));
+
+	SignatureOk = 1;
+	for (i = 0; i < sizeof(HdcpSignature); i++) {
+		if (HdcpSignature[i] != HdcpSignatureBuffer[i])
+			SignatureOk = 0;
+	}
+
+	/* password and buffer are correct, as the generated key could correctly decrypt the signature */
+	if (SignatureOk == 1) {
+		/* decrypt the keys */
+		Decrypt(&Buffer[HDCP22_LC128_OFFSET], Hdcp22Lc128, Key, Hdcp22Lc128Size);
+		Decrypt(&Buffer[HDCP22_CERTIFICATE_OFFSET], Hdcp22RxPrivateKey, Key, Hdcp22RxPrivateKeySize);
+		Decrypt(&Buffer[HDCP14_KEY1_OFFSET], Hdcp14KeyA, Key, Hdcp14KeyASize);
+		Decrypt(&Buffer[HDCP14_KEY2_OFFSET], Hdcp14KeyB, Key, Hdcp14KeyBSize);
+		return XST_SUCCESS;
+	} else {
+		printk(KERN_INFO "HDCP key store signature mismatch; HDCP key data and/or password are invalid.\n");
+	}
+	return XST_FAILURE;
+}
+
+/* assume the HDCP C structures containing the keys are valid, and sets them in the bare-metal driver / IP */
+static int hdcp_keys_configure(struct xhdmi_device *xhdmi)
+{
+	XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	if (xhdmi->config.Hdcp14.IsPresent && xhdmi->config.HdcpTimer.IsPresent && xhdmi->hdcp1x_keymngmt_iomem) {
+		u8 Status;
+		dev_dbg(xhdmi->dev,"HDCP1x components are all there.\n");
+		/* Set pointer to HDCP 1.4 key */
+		XV_HdmiRxSs_HdcpSetKey(HdmiRxSsPtr, XV_HDMIRXSS_KEY_HDCP14, xhdmi->Hdcp14KeyB);
+		/* Key manager Init */
+		Status = XHdcp_KeyManagerInit((uintptr_t)xhdmi->hdcp1x_keymngmt_iomem, HdmiRxSsPtr->Hdcp14KeyPtr);
+		if (Status != XST_SUCCESS) {
+			dev_err(xhdmi->dev, "HDCP 1.4 RX Key Manager initialization error.\n");
+			return -EINVAL;
+		}
+		dev_info(xhdmi->dev, "HDCP 1.4 RX Key Manager initialized OK.\n");
+	}
+	if (xhdmi->config.Hdcp22.IsPresent) {
+		/* Set pointer to HDCP 2.2 LC128 */
+		XV_HdmiRxSs_HdcpSetKey(HdmiRxSsPtr, XV_HDMIRXSS_KEY_HDCP22_LC128, xhdmi->Hdcp22Lc128);
+		/* Set pointer to HDCP 2.2 private key */
+		XV_HdmiRxSs_HdcpSetKey(HdmiRxSsPtr, XV_HDMIRXSS_KEY_HDCP22_PRIVATE, xhdmi->Hdcp22PrivateKey);
+	}
+	return 0;
+}
+
+/* the EEPROM contents (i.e. the encrypted HDCP keys) must be dumped as a binary blob;
+ * the user must first upload the password */
+static ssize_t hdcp_key_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+	XV_HdmiRxSs *HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+
+	/* check for valid size of HDCP encrypted key binary blob, @TODO adapt */
+	if (count < 1872) {
+		printk(KERN_INFO "hdcp_key_store(count = %d, expected >=1872)\n", (int)count);
+		return -EINVAL;
+	}
+	xhdmi->hdcp_password_accepted = 0;
+	/* decrypt the keys from the binary blob (buffer) into the C structures for keys */
+	if (XHdcp_LoadKeys((const u8*)buf, xhdmi->hdcp_password,
+		xhdmi->Hdcp22Lc128, sizeof(xhdmi->Hdcp22Lc128),
+		xhdmi->Hdcp22PrivateKey, sizeof(xhdmi->Hdcp22PrivateKey),
+		xhdmi->Hdcp14KeyA, sizeof(xhdmi->Hdcp14KeyA),
+		xhdmi->Hdcp14KeyB, sizeof(xhdmi->Hdcp14KeyB)) == XST_SUCCESS) {
+
+		xhdmi->hdcp_password_accepted = 1;
+		/* configure the keys in the IP */
+		hdcp_keys_configure(xhdmi);
+
+		/* configure HDCP in HDMI */
+		u8 Status = XV_HdmiRxSs_CfgInitializeHdcp(HdmiRxSsPtr, &xhdmi->config, (uintptr_t)xhdmi->iomem);
+		if (Status != XST_SUCCESS) {
+			dev_err(xhdmi->dev, "XV_HdmiRxSs_CfgInitializeHdcp() failed with error %d\n", Status);
+			return -EINVAL;
+		}
+
+		XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_HDCP_AUTHENTICATED,
+			RxHdcpAuthenticatedCallback, (void *)xhdmi);
+		XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_HDCP_UNAUTHENTICATED,
+			RxHdcpUnauthenticatedCallback, (void *)xhdmi);
+		XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_HDCP_ENCRYPTION_UPDATE,
+			RxHdcpEncryptionUpdateCallback, (void *)xhdmi);
+
+		if (HdmiRxSsPtr->Config.Hdcp14.IsPresent || HdmiRxSsPtr->Config.Hdcp22.IsPresent) {
+			if (xhdmi->cable_is_connected) {
+				// Push connect event to HDCP event queue
+				XV_HdmiRxSs_HdcpPushEvent(HdmiRxSsPtr, XV_HDMIRXSS_HDCP_CONNECT_EVT);
+				/* Force HPD toggle */
+				XV_HdmiRxSs_ToggleHpd(HdmiRxSsPtr);
+			}
+			/* call into hdcp_poll_work, which will reschedule itself */
+			hdcp_poll_work(&xhdmi->delayed_work_hdcp_poll.work);
+		}
+	}
+	return count;
+}
+
+static ssize_t hdcp_password_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%s", xhdmi->hdcp_password_accepted? "accepted": "rejected");
+	return count;
+}
+
+/* store the HDCP key password, after this the HDCP key can be written to sysfs */
+static ssize_t hdcp_password_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	int i = 0;
+	struct xhdmi_device *xhdmi = (struct xhdmi_device *)dev_get_drvdata(sysfs_dev);
+
+	if (count > sizeof(xhdmi->hdcp_password)) return -EINVAL;
+	/* copy password characters up to newline or carriage return */
+	while ((i < count) && (i < sizeof(xhdmi->hdcp_password))) {
+		/* do not include newline or carriage return in password */
+		if ((buf[i] == '\n') || (buf[i] == '\r') || (buf[i] == 0)) break;
+		xhdmi->hdcp_password[i] = buf[i];
+		i++;
+	}
+	/* zero remaining characters */
+	while (i < sizeof(xhdmi->hdcp_password)) {
+		xhdmi->hdcp_password[i] = 0;
+		i++;
+	}
+	return count;
+}
+
+static DEVICE_ATTR(vphy_log,  0444, vphy_log_show, NULL/*null_store*/);
+static DEVICE_ATTR(vphy_info, 0444, vphy_info_show, NULL/*null_store*/);
+static DEVICE_ATTR(hdmi_log,  0444, hdmi_log_show, NULL/*null_store*/);
+static DEVICE_ATTR(hdcp_log,  0444, hdcp_log_show, NULL/*null_store*/);
+static DEVICE_ATTR(hdmi_info, 0444, hdmi_info_show, NULL/*null_store*/);
+static DEVICE_ATTR(hdcp_debugen, 0220, NULL/*show*/, hdcp_debugen_store);
+static DEVICE_ATTR(hdcp_key, 0220, NULL/*null_show*/, hdcp_key_store);
+static DEVICE_ATTR(hdcp_password, 0660, hdcp_password_show, hdcp_password_store);
+/* read-only status */
+static DEVICE_ATTR(hdcp_authenticated, 0444, hdcp_authenticated_show, NULL/*store*/);
+static DEVICE_ATTR(hdcp_encrypted, 0444, hdcp_encrypted_show, NULL/*store*/);
+
+static struct attribute *attrs[] = {
+	&dev_attr_vphy_log.attr,
+	&dev_attr_vphy_info.attr,
+	&dev_attr_hdmi_log.attr,
+	&dev_attr_hdcp_log.attr,
+	&dev_attr_hdmi_info.attr,
+	&dev_attr_hdcp_debugen.attr,
+	&dev_attr_hdcp_key.attr,
+	&dev_attr_hdcp_password.attr,
+	&dev_attr_hdcp_authenticated.attr,
+	&dev_attr_hdcp_encrypted.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+static int xhdmi_parse_of(struct xhdmi_device *xhdmi, XV_HdmiRxSs_Config *config)
+{
+	struct device *dev = xhdmi->dev;
+	struct device_node *node = dev->of_node;
+	int rc;
+	bool isHdcp14_en, isHdcp22_en;
+	u32 val = 0;
+
+	rc = of_property_read_u32(node, "xlnx,input-pixels-per-clock", &val);
+	if (rc < 0)
+		goto error_dt;
+	config->Ppc = val;
+
+	rc = of_property_read_u32(node, "xlnx,max-bits-per-component", &val);
+	if (rc < 0)
+		goto error_dt;
+	config->MaxBitsPerPixel = val;
+
+	rc = of_property_read_u32(node, "xlnx,edid-ram-size", &val);
+	if (rc == 0) {
+		if (val % 128)
+			goto error_dt;
+		xhdmi->edid_blocks_max = val / EDID_BLOCK_SIZE;
+	}
+
+	/* RX Core */
+	config->HdmiRx.DeviceId = RX_DEVICE_ID_BASE + instance;
+	config->HdmiRx.IsPresent = 1;
+	config->HdmiRx.AbsAddr = RXSS_RX_OFFSET;
+	XV_HdmiRx_ConfigTable[instance].DeviceId = RX_DEVICE_ID_BASE + instance;
+	XV_HdmiRx_ConfigTable[instance].BaseAddress = RXSS_RX_OFFSET;
+
+	isHdcp14_en = of_property_read_bool(node, "xlnx,include-hdcp-1-4");
+	isHdcp22_en = of_property_read_bool(node, "xlnx,include-hdcp-2-2");
+	xhdmi->audio_enabled =
+		of_property_read_bool(node, "xlnx,audio-enabled");
+
+	if (isHdcp14_en) {
+		/* HDCP14 Core */
+		/* make subcomponent of RXSS present */
+		config->Hdcp14.DeviceId = RX_DEVICE_ID_BASE + instance;
+		config->Hdcp14.IsPresent = 1;
+		config->Hdcp14.AbsAddr = RXSS_HDCP14_OFFSET;
+		/* and configure it */
+		XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES/2 + instance].DeviceId = config->Hdcp14.DeviceId;
+		XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES/2 + instance].BaseAddress = RXSS_HDCP14_OFFSET;
+		XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES/2 + instance].IsRx = 1;
+		XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES/2 + instance].IsHDMI = 1;
+
+		/* HDCP14 Timer Core */
+		/* make subcomponent of RXSS present */
+		config->HdcpTimer.DeviceId = RX_DEVICE_ID_BASE + instance;
+		config->HdcpTimer.IsPresent = 1;
+		config->HdcpTimer.AbsAddr = RXSS_HDCP14_TIMER_OFFSET;
+		/* and configure it */
+		XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 0].DeviceId = config->HdcpTimer.DeviceId;
+		XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 0].BaseAddress = RXSS_HDCP14_TIMER_OFFSET;
+		/* @TODO increment timer index */
+	}
+
+	if (isHdcp22_en) {
+		/* HDCP22 SS */
+		config->Hdcp22.DeviceId = RX_DEVICE_ID_BASE + instance;
+		config->Hdcp22.IsPresent = 1;
+		config->Hdcp22.AbsAddr = RXSS_HDCP22_OFFSET;
+		XHdcp22_Rx_ConfigTable[instance].DeviceId = config->Hdcp22.DeviceId;
+		XHdcp22_Rx_ConfigTable[instance].BaseAddress = RXSS_HDCP22_OFFSET;
+		XHdcp22_Rx_ConfigTable[instance].Protocol = 0; /*HDCP22_RX_HDMI*/
+		XHdcp22_Rx_ConfigTable[instance].Mode = 0; /*XHDCP22_RX_RECEIVER*/
+		XHdcp22_Rx_ConfigTable[instance].TimerDeviceId = RX_DEVICE_ID_BASE + instance;
+		XHdcp22_Rx_ConfigTable[instance].CipherDeviceId = RX_DEVICE_ID_BASE + instance;
+		XHdcp22_Rx_ConfigTable[instance].MontMultDeviceId = RX_DEVICE_ID_BASE + instance;
+		XHdcp22_Rx_ConfigTable[instance].RngDeviceId = RX_DEVICE_ID_BASE + instance;
+
+		/* HDCP22 Cipher Core */
+		XHdcp22_Cipher_ConfigTable[XPAR_XHDCP22_CIPHER_NUM_INSTANCES/2 + instance].DeviceId = RX_DEVICE_ID_BASE + instance;
+		XHdcp22_Cipher_ConfigTable[XPAR_XHDCP22_CIPHER_NUM_INSTANCES/2 + instance].BaseAddress = RX_HDCP22_CIPHER_OFFSET;
+		/* HDCP22 MMULT Core */
+		XHdcp22_mmult_ConfigTable[XPAR_XHDCP22_MMULT_NUM_INSTANCES/2 + instance].DeviceId = RX_DEVICE_ID_BASE + instance;
+		XHdcp22_mmult_ConfigTable[XPAR_XHDCP22_MMULT_NUM_INSTANCES/2 + instance].BaseAddress = RX_HDCP2_MMULT_OFFSET;
+		/* HDCP22-Timer Core */
+		XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 1].DeviceId = RX_DEVICE_ID_BASE + 64 + instance;
+		XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 1].BaseAddress = RX_HDCP22_TIMER_OFFSET;
+		/* HDCP22 RNG Core */
+		XHdcp22_Rng_ConfigTable[XPAR_XHDCP22_RNG_NUM_INSTANCES/2 + instance].DeviceId = RX_DEVICE_ID_BASE + instance;
+		XHdcp22_Rng_ConfigTable[XPAR_XHDCP22_RNG_NUM_INSTANCES/2 + instance].BaseAddress = RX_HDCP22_RNG_OFFSET;
+	}
+
+
+	return 0;
+
+error_dt:
+		dev_err(xhdmi->dev, "Error parsing device tree");
+		return rc;
+}
+
+static int xhdmi_probe(struct platform_device *pdev)
+{
+	struct v4l2_subdev *subdev;
+	struct xhdmi_device *xhdmi;
+	int ret, i;
+	unsigned int index = 0;
+	struct resource *res;
+
+	const struct firmware *fw_edid;
+	const char *fw_edid_name = "xilinx/xilinx-hdmi-rx-edid.bin";
+	unsigned long flags;
+	unsigned long axi_clk_rate;
+
+	XV_HdmiRxSs *HdmiRxSsPtr;
+	struct xlnx_hdmirx_audio_data *adata;
+	u32 Status;
+
+	dev_info(&pdev->dev, "probe started\n");
+	/* allocate zeroed HDMI RX device structure */
+	xhdmi = devm_kzalloc(&pdev->dev, sizeof(*xhdmi), GFP_KERNEL);
+	if (!xhdmi)
+		return -ENOMEM;
+	xhdmi->rx_audio_data =
+		devm_kzalloc(&pdev->dev, sizeof(struct xlnx_hdmirx_audio_data),
+			     GFP_KERNEL);
+	if (!xhdmi->rx_audio_data)
+		return -ENOMEM;
+
+	adata = xhdmi->rx_audio_data;
+	/* store pointer of the real device inside platform device */
+	xhdmi->dev = &pdev->dev;
+
+	xhdmi->edid_blocks_max = 2;
+
+	/* mutex that protects against concurrent access */
+	mutex_init(&xhdmi->xhdmi_mutex);
+	spin_lock_init(&xhdmi->irq_lock);
+	/* work queues */
+	xhdmi->work_queue = create_singlethread_workqueue("xilinx-hdmi-rx");
+	if (!xhdmi->work_queue) {
+		dev_info(xhdmi->dev, "Could not create work queue\n");
+		return -ENOMEM;
+	}
+
+	INIT_DELAYED_WORK(&xhdmi->delayed_work_enable_hotplug,
+		xhdmi_delayed_work_enable_hotplug);
+
+	dev_dbg(xhdmi->dev,"DT parse start\n");
+	/* parse open firmware device tree data */
+	ret = xhdmi_parse_of(xhdmi, &xhdmi->config);
+	if (ret < 0)
+		return ret;
+	dev_dbg(xhdmi->dev,"DT parse done\n");
+
+	/* acquire vphy lanes */
+	for (index = 0; index < 3; index++)
+	{
+		static const struct of_device_id xlnx_hdmi_phy_id_table[] = {
+			{ .compatible = "xlnx,hdmi-gt-controller-1.0", },
+			{ .compatible = "xlnx,vid-phy-controller-2.2", },
+			{ /* end of table */ },
+		};
+		const struct of_device_id *match;
+
+		char phy_name[16];
+		snprintf(phy_name, sizeof(phy_name), "hdmi-phy%d", index);
+		xhdmi->phy[index] = devm_phy_get(xhdmi->dev, phy_name);
+		if (IS_ERR(xhdmi->phy[index])) {
+			ret = PTR_ERR(xhdmi->phy[index]);
+			xhdmi->phy[index] = NULL;
+			if (ret == -EPROBE_DEFER) {
+				dev_info(xhdmi->dev, "xvphy/xgtphy not ready -EPROBE_DEFER\n");
+				return ret;
+			}
+			if (ret != -EPROBE_DEFER)
+				dev_err(xhdmi->dev, "failed to get phy lane %s index %d, error %d\n",
+					phy_name, index, ret);
+			goto error_phy;
+		}
+
+		match = of_match_node(xlnx_hdmi_phy_id_table, xhdmi->phy[index]->dev.parent->of_node);
+		if (!match) {
+			dev_err(xhdmi->dev, "of_match_node failed for phy!\n");
+			goto error_phy;
+		}
+
+		if (strncmp(match->compatible, "xlnx,vid-phy-controller", 23) == 0)
+			xhdmi->isvphy = 1;
+		else
+			xhdmi->isvphy = 0;
+
+		ret = phy_init(xhdmi->phy[index]);
+		if (ret) {
+			dev_err(xhdmi->dev,
+				"failed to init phy lane %d\n", index);
+			goto error_phy;
+		}
+	}
+
+	/* get ownership of the HDMI RXSS MMIO register space resource */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(xhdmi->dev, "unable to get register space resource!\n");
+		return -EINVAL;
+	}
+	/* map the MMIO region */
+	xhdmi->iomem = devm_ioremap_resource(xhdmi->dev, res);
+	if (IS_ERR(xhdmi->iomem)) {
+		ret = PTR_ERR(xhdmi->iomem);
+		goto error_resource;
+	}
+	xhdmi->config.DeviceId = instance;
+	xhdmi->config.BaseAddress = (uintptr_t)xhdmi->iomem;
+	xhdmi->config.HighAddress = (uintptr_t)xhdmi->iomem + resource_size(res) - 1;
+
+	/* Compute AbsAddress for sub-cores */
+	ret = xhdmi_compute_subcore_AbsAddr(&xhdmi->config);
+	if (ret == -EFAULT) {
+	   dev_err(xhdmi->dev, "hdmi-rx sub-core address out-of range\n");
+	   return ret;
+	}
+
+	/* video streaming bus clock */
+	xhdmi->clk = devm_clk_get(xhdmi->dev, "s_axis_video_aclk");
+	if (IS_ERR(xhdmi->clk)) {
+		ret = PTR_ERR(xhdmi->clk);
+		if (ret == -EPROBE_DEFER)
+			dev_info(xhdmi->dev, "video-clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(xhdmi->dev, "failed to get video clk\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xhdmi->clk);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed enable AXI4 stream clk\n");
+		return ret;
+	}
+
+	/* AXI lite register bus clock */
+	xhdmi->axi_lite_clk = devm_clk_get(xhdmi->dev, "s_axi_cpu_aclk");
+	if (IS_ERR(xhdmi->axi_lite_clk)) {
+		ret = PTR_ERR(xhdmi->axi_lite_clk);
+		if (ret == -EPROBE_DEFER)
+			dev_info(xhdmi->dev, "axi-lite clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(xhdmi->dev, "failed to get axi-lite clk\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xhdmi->axi_lite_clk);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed enable axi-lite clk\n");
+		return ret;
+	}
+
+	axi_clk_rate = clk_get_rate(xhdmi->axi_lite_clk);
+	dev_dbg(xhdmi->dev,"AXI Lite clock rate = %lu Hz\n", axi_clk_rate);
+
+	/* we now know the AXI clock rate */
+	XHdcp1x_ConfigTable[XPAR_XHDCP_NUM_INSTANCES/2 + instance].SysFrequency = axi_clk_rate;
+	XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 0].SysClockFreqHz = axi_clk_rate;
+	XTmrCtr_ConfigTable[XPAR_XTMRCTR_NUM_INSTANCES/2 + instance * 2 + 1].SysClockFreqHz = axi_clk_rate;
+	XV_HdmiRx_ConfigTable[instance].AxiLiteClkFreq = axi_clk_rate;
+
+	/* get ownership of the HDCP1x key management MMIO register space resource */
+	if (xhdmi->config.Hdcp14.IsPresent) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hdcp1x-keymngmt");
+
+		if (res) {
+			dev_dbg(xhdmi->dev,"Mapping HDCP1x key management block.\n");
+			xhdmi->hdcp1x_keymngmt_iomem = devm_ioremap_resource(xhdmi->dev, res);
+			dev_dbg(xhdmi->dev,"HDCP1x key management block @%p.\n", xhdmi->hdcp1x_keymngmt_iomem);
+			if (IS_ERR(xhdmi->hdcp1x_keymngmt_iomem)) {
+				dev_err(xhdmi->dev, "Could not ioremap hdcp1x-keymngmt.\n");
+				return PTR_ERR(xhdmi->hdcp1x_keymngmt_iomem);
+			}
+		}
+	}
+
+	/* get HDMI RXSS irq */
+	xhdmi->irq = platform_get_irq(pdev, 0);
+	if (xhdmi->irq <= 0) {
+		dev_err(&pdev->dev, "platform_get_irq() failed\n");
+		return xhdmi->irq;
+	}
+
+	if (xhdmi->config.Hdcp14.IsPresent) {
+		xhdmi->hdcp1x_irq = platform_get_irq_byname(pdev, "hdcp14_irq");
+		dev_dbg(xhdmi->dev,"xhdmi->hdcp1x_irq = %d\n", xhdmi->hdcp1x_irq);
+		xhdmi->hdcp1x_timer_irq = platform_get_irq_byname(pdev, "hdcp14_timer_irq");
+		dev_dbg(xhdmi->dev,"xhdmi->hdcp1x_timer_irq = %d\n", xhdmi->hdcp1x_timer_irq);
+	}
+
+	if (xhdmi->config.Hdcp22.IsPresent) {
+		xhdmi->hdcp22_irq = platform_get_irq_byname(pdev, "hdcp22_irq");
+		dev_dbg(xhdmi->dev,"xhdmi->hdcp22_irq = %d\n", xhdmi->hdcp22_irq);
+		xhdmi->hdcp22_timer_irq = platform_get_irq_byname(pdev, "hdcp22_timer_irq");
+		dev_dbg(xhdmi->dev,"xhdmi->hdcp22_timer_irq = %d\n", xhdmi->hdcp22_timer_irq);
+	}
+
+	if (xhdmi->config.Hdcp14.IsPresent || xhdmi->config.Hdcp22.IsPresent) {
+	  INIT_DELAYED_WORK(&xhdmi->delayed_work_hdcp_poll, hdcp_poll_work/*function*/);
+	}
+
+	/* create sysfs group entry */
+	ret = sysfs_create_group(&xhdmi->dev->kobj, &attr_group);
+	if (ret) {
+		dev_err(xhdmi->dev, "sysfs group creation (%d) failed \n", ret);
+		return ret;
+	}
+
+	HdmiRxSsPtr = (XV_HdmiRxSs *)&xhdmi->xv_hdmirxss;
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+
+	ret = devm_request_threaded_irq(&pdev->dev, xhdmi->irq, hdmirx_irq_handler, hdmirx_irq_thread,
+		IRQF_TRIGGER_HIGH, "xilinx-hdmi-rx", xhdmi/*dev_id*/);
+
+	if (ret) {
+		dev_err(&pdev->dev, "unable to request IRQ %d\n", xhdmi->irq);
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		goto error_phy;
+	}
+
+	/* HDCP 1.4 Cipher interrupt */
+	if (xhdmi->hdcp1x_irq > 0) {
+		/* Request the HDCP14 interrupt */
+		ret = devm_request_threaded_irq(&pdev->dev, xhdmi->hdcp1x_irq, hdmirx_hdcp_irq_handler, hdmirx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmirxss-hdcp1x-cipher", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(&pdev->dev, "unable to request IRQ %d\n", xhdmi->hdcp1x_irq);
+			hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+			return ret;
+		}
+	}
+
+	/* HDCP 1.4 Timer interrupt */
+	if (xhdmi->hdcp1x_timer_irq > 0) {
+		/* Request the HDCP14 interrupt */
+		ret = devm_request_threaded_irq(&pdev->dev, xhdmi->hdcp1x_timer_irq, hdmirx_hdcp_irq_handler, hdmirx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmirxss-hdcp1x-timer", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(&pdev->dev, "unable to request IRQ %d\n", xhdmi->hdcp1x_timer_irq);
+			hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+			return ret;
+		}
+	}
+
+	/* HDCP 2.2 interrupt, unused currently */
+#if 0
+	if (xhdmi->hdcp22_irq > 0) {
+		/* Request the HDCP22 interrupt */
+		ret = devm_request_threaded_irq(&pdev->dev, xhdmi->hdcp22_irq, hdmirx_hdcp_irq_handler, hdmirx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmirxss-hdcp22", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(&pdev->dev, "unable to request IRQ %d\n", xhdmi->hdcp22_irq);
+				hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+			hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+			return ret;
+		}
+	}
+#endif
+	/* HDCP 2.2 Timer interrupt */
+	if (xhdmi->hdcp22_timer_irq > 0) {
+		/* Request the HDCP22 timer interrupt */
+		ret = devm_request_threaded_irq(&pdev->dev, xhdmi->hdcp22_timer_irq, hdmirx_hdcp_irq_handler, hdmirx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmirxss-hdcp22-timer", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(&pdev->dev, "unable to request IRQ %d\n", xhdmi->hdcp22_timer_irq);
+				hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+			hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+
+			return ret;
+		}
+	}
+
+	/* sets pointer to the EDID used by XV_HdmiRxSs_LoadDefaultEdid() */
+	XV_HdmiRxSs_SetEdidParam(HdmiRxSsPtr, (u8 *)&xilinx_edid[0], sizeof(xilinx_edid));
+
+	/* Initialize top level and all included sub-cores */
+	Status = XV_HdmiRxSs_CfgInitialize(HdmiRxSsPtr, &xhdmi->config, (uintptr_t)xhdmi->iomem);
+	if (Status != XST_SUCCESS) {
+		dev_err(xhdmi->dev, "initialization failed with error %d\n", Status);
+		return -EINVAL;
+	}
+
+	/* disable interrupts */
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiRxSs_IntrDisable(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* retrieve EDID */
+	if (request_firmware(&fw_edid, fw_edid_name, xhdmi->dev) == 0) {
+		int blocks = fw_edid->size / 128;
+		if ((blocks == 0) || (blocks > xhdmi->edid_blocks_max) || (fw_edid->size % 128)) {
+			dev_err(xhdmi->dev, "%s must be n * 128 bytes, with 1 <= n <= %d, using Xilinx built-in EDID instead.\n",
+				fw_edid_name, xhdmi->edid_blocks_max);
+		} else {
+			memcpy(xhdmi->edid_user, fw_edid->data, 128 * blocks);
+			xhdmi->edid_user_blocks = blocks;
+		}
+	}
+	release_firmware(fw_edid);
+
+	if (xhdmi->edid_user_blocks) {
+		dev_info(xhdmi->dev, "Using %d EDID block%s (%d bytes) from '%s'.\n",
+			xhdmi->edid_user_blocks, xhdmi->edid_user_blocks > 1? "s":"",
+			128 * (u16)xhdmi->edid_user_blocks, fw_edid_name);
+		XV_HdmiRxSs_LoadEdid(HdmiRxSsPtr, (u8 *)&xhdmi->edid_user,
+				     128 * (u16)xhdmi->edid_user_blocks);
+	} else {
+		dev_info(xhdmi->dev, "Using Xilinx built-in EDID.\n");
+		XV_HdmiRxSs_LoadDefaultEdid(HdmiRxSsPtr);
+	}
+
+	/* RX SS callback setup (from xapp1287/xhdmi_example.c:2146) */
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_CONNECT,
+		RxConnectCallback, (void *)xhdmi);
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_STREAM_DOWN,
+		RxStreamDownCallback, (void *)xhdmi);
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_STREAM_INIT,
+		RxStreamInitCallback, (void *)xhdmi);
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_STREAM_UP,
+		RxStreamUpCallback, (void *)xhdmi);
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_BRDGOVERFLOW,
+		RxBrdgOverflowCallback, (void *)xhdmi);
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_AUD,
+		RxAudCallback, (void *)xhdmi);
+	XV_HdmiRxSs_SetCallback(HdmiRxSsPtr, XV_HDMIRXSS_HANDLER_AUX,
+		RxAuxCallback, (void *)xhdmi);
+
+	/* get a reference to the XVphy/ XHdmiphy1 data structure */
+	if (xhdmi->isvphy)
+		xhdmi->xvphy = xvphy_get_xvphy(xhdmi->phy[0]);
+	else
+		xhdmi->xgtphy = xvphy_get_xvphy(xhdmi->phy[0]);
+
+	xvphy_mutex_lock(xhdmi->phy[0]);
+	/* the callback is not specific to a single lane, but we need to
+	 * provide one of the phy's as reference */
+	if (xhdmi->isvphy) {
+		XVphy_SetHdmiCallback(xhdmi->xvphy, XVPHY_HDMI_HANDLER_RXINIT,
+			VphyHdmiRxInitCallback, (void *)xhdmi);
+		XVphy_SetHdmiCallback(xhdmi->xvphy, XVPHY_HDMI_HANDLER_RXREADY,
+			VphyHdmiRxReadyCallback, (void *)xhdmi);
+	} else {
+		XHdmiphy1_SetHdmiCallback(xhdmi->xgtphy, XHDMIPHY1_HDMI_HANDLER_RXINIT,
+			VphyHdmiRxInitCallback, (void *)xhdmi);
+		XHdmiphy1_SetHdmiCallback(xhdmi->xgtphy, XHDMIPHY1_HDMI_HANDLER_RXREADY,
+			VphyHdmiRxReadyCallback, (void *)xhdmi);
+	}
+
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+
+	platform_set_drvdata(pdev, xhdmi);
+
+	/* Initialize V4L2 subdevice */
+	subdev = &xhdmi->subdev;
+	v4l2_subdev_init(subdev, &xhdmi_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xhdmi_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	v4l2_set_subdevdata(subdev, xhdmi);
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+
+	/* Initialize V4L2 media entity */
+	xhdmi->pad.flags = MEDIA_PAD_FL_SOURCE;
+	subdev->entity.ops = &xhdmi_media_ops;
+	ret = media_entity_pads_init(&subdev->entity, 1/*npads*/, &xhdmi->pad);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to init media entity\n");
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		goto error_irq;
+	}
+
+	ret = v4l2_ctrl_handler_init(&xhdmi->ctrl_handler,
+				ARRAY_SIZE(xhdmi_ctrls)/*controls*/);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to initialize V4L2 ctrl\n");
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		goto error_irq;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(xhdmi_ctrls); i++) {
+		struct v4l2_ctrl *ctrl;
+
+		dev_dbg(&pdev->dev, "%d ctrl = 0x%x\n", i,
+			xhdmi_ctrls[i].id);
+		ctrl = v4l2_ctrl_new_custom(&xhdmi->ctrl_handler,
+					    &xhdmi_ctrls[i], NULL);
+		if (!ctrl) {
+			dev_err(&pdev->dev, "Failed for %s ctrl\n",
+				xhdmi_ctrls[i].name);
+			v4l2_ctrl_handler_free(&xhdmi->ctrl_handler);
+			hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+			goto error_irq;
+		}
+	}
+
+	if (xhdmi->ctrl_handler.error) {
+		dev_err(&pdev->dev, "failed to add controls\n");
+		ret = xhdmi->ctrl_handler.error;
+		v4l2_ctrl_handler_free(&xhdmi->ctrl_handler);
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		goto error_irq;
+	}
+
+	subdev->ctrl_handler = &xhdmi->ctrl_handler;
+	ret = v4l2_ctrl_handler_setup(&xhdmi->ctrl_handler);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to set controls\n");
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		goto error_irq;
+	}
+
+	/* assume detected format */
+	xhdmi->detected_format.width = 1280;
+	xhdmi->detected_format.height = 720;
+	xhdmi->detected_format.field = V4L2_FIELD_NONE;
+	xhdmi->detected_format.colorspace = V4L2_COLORSPACE_REC709;
+	xhdmi->detected_format.code = MEDIA_BUS_FMT_RBG888_1X24;
+	xhdmi->detected_format.colorspace = V4L2_COLORSPACE_SRGB;
+	xhdmi->detected_format.xfer_func = V4L2_XFER_FUNC_DEFAULT;
+	xhdmi->detected_format.ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+	xhdmi->detected_format.quantization = V4L2_QUANTIZATION_DEFAULT;
+
+	ret = v4l2_async_register_subdev(subdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to register subdev\n");
+		hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+		goto error;
+	}
+
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+
+	/* enable interrupts */
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiRxSs_IntrEnable(HdmiRxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* probe has succeeded for this instance, increment instance index */
+	instance++;
+
+	if (xhdmi->audio_enabled) {
+		ret = hdmirx_register_aud_dev(xhdmi->dev);
+		if (ret < 0) {
+			xhdmi->audio_init = false;
+			dev_err(xhdmi->dev, "hdmi rx audio init failed\n");
+		} else {
+			xhdmi->audio_init = true;
+			init_waitqueue_head(&adata->audio_update_q);
+			dev_info(xhdmi->dev, "hdmi rx audio initialized\n");
+		}
+	}
+	/* return success */
+	dev_info(xhdmi->dev, "probe successful\n");
+	return 0;
+
+error:
+	v4l2_ctrl_handler_free(&xhdmi->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+error_irq:
+
+error_phy:
+	printk(KERN_INFO "xhdmirx_probe() error_phy:\n");
+	index = 0;
+	/* release the lanes that we did get, if we did not get all lanes */
+	if (xhdmi->phy[index]) {
+		printk(KERN_INFO "phy_exit() xhdmi->phy[%d] = %p\n", index, xhdmi->phy[index]);
+		phy_exit(xhdmi->phy[index]);
+		xhdmi->phy[index] = NULL;
+	}
+error_resource:
+	printk(KERN_INFO "xhdmirx_probe() error_resource:\n");
+	return ret;
+}
+
+static int xhdmi_remove(struct platform_device *pdev)
+{
+	struct xhdmi_device *xhdmi = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xhdmi->subdev;
+	unsigned long flags;
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiRxSs_IntrDisable(&xhdmi->xv_hdmirxss);
+	xhdmi->teardown = 1;
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	cancel_delayed_work(&xhdmi->delayed_work_enable_hotplug);
+	destroy_workqueue(xhdmi->work_queue);
+
+	sysfs_remove_group(&pdev->dev.kobj, &attr_group);
+	v4l2_async_unregister_subdev(subdev);
+	v4l2_ctrl_handler_free(&xhdmi->ctrl_handler);
+	media_entity_cleanup(&subdev->entity);
+	clk_disable_unprepare(xhdmi->clk);
+	if (xhdmi->audio_init)
+		hdmirx_unregister_aud_dev(&pdev->dev);
+	dev_dbg(xhdmi->dev,"removed.\n");
+	return 0;
+}
+
+static const struct dev_pm_ops xhdmirx_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(hdmirx_pm_suspend, hdmirx_pm_resume)
+};
+
+static const struct of_device_id xhdmi_of_id_table[] = {
+	{ .compatible = "xlnx,v-hdmi-rx-ss-3.1" },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xhdmi_of_id_table);
+
+static struct platform_driver xhdmi_driver = {
+	.driver = {
+		.name		= "xilinx-hdmi-rx",
+		.pm		= &xhdmirx_pm_ops,
+		.of_match_table	= xhdmi_of_id_table,
+	},
+	.probe			= xhdmi_probe,
+	.remove			= xhdmi_remove,
+};
+
+struct xlnx_hdmirx_audio_data *hdmirx_get_audio_data(struct device *dev)
+{
+	struct xhdmi_device *xhdmi = dev_get_drvdata(dev);
+
+	if (!xhdmi)
+		return NULL;
+	else
+		return xhdmi->rx_audio_data;
+}
+
+u32 hdmirx_audio_startup(struct device *dev)
+{
+	int err;
+	struct xlnx_hdmirx_audio_data *adata;
+	unsigned long jiffies = msecs_to_jiffies(XHDMI_AUDIO_DETECT_TIMEOUT);
+	struct xhdmi_device *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+	adata = xhdmi->rx_audio_data;
+
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	XV_HdmiRx_AudioEnable(HdmiRxSsPtr->HdmiRxPtr);
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+
+	err = wait_event_interruptible_timeout(adata->audio_update_q,
+					       adata->audio_detected,
+					       jiffies);
+	if (!err) {
+		dev_err(dev, "No audio detected in input stream\n");
+		return 0;
+	}
+
+	return adata->num_channels;
+}
+
+void hdmirx_audio_shutdown(struct device *dev)
+{
+	struct xhdmi_device *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiRxSs *HdmiRxSsPtr = &xhdmi->xv_hdmirxss;
+
+	hdmi_mutex_lock(&xhdmi->xhdmi_mutex);
+	XV_HdmiRx_AudioDisable(HdmiRxSsPtr->HdmiRxPtr);
+	hdmi_mutex_unlock(&xhdmi->xhdmi_mutex);
+}
+
+module_platform_driver(xhdmi_driver);
+
+MODULE_DESCRIPTION("Xilinx HDMI RXSS V4L2 driver");
+MODULE_AUTHOR("Leon Woestenberg <leon@sidebranch.com>");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xilinx_drm_hdmi.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xilinx_drm_hdmi.c
@@ -0,0 +1,3207 @@
+/*
+ * Xilinx DRM HDMI encoder driver
+ *
+ * Xilinx HDMI-Tx Subsystem driver
+ * Copyright (C) 2018 Rohit Consul <rohitco@xilinx.com>
+ *
+ * Authors: Rohit Consul <rohitco@xilinx.com>
+ *			Leon Woestenberg <leon@sidebranch.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_of.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_sysfs.h>
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/component.h>
+#include <linux/device.h>
+#include <linux/hdmi.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/sysfs.h>
+#include <linux/workqueue.h>
+#include <uapi/linux/media-bus-format.h>
+#include "../drivers/gpu/drm/xlnx/xlnx_bridge.h"
+
+#include "linux/phy/phy-vphy.h"
+
+/* baseline driver includes */
+#include "xilinx-hdmi-tx/xv_hdmitxss.h"
+
+/* for the HMAC, using password to decrypt HDCP keys */
+#include "phy-xilinx-vphy/xhdcp22_common.h"
+#include "phy-xilinx-vphy/aes256.h"
+
+#include "xlnx_hdmitx_audio.h"
+
+#define HDMI_MAX_LANES				4
+
+#define XVPHY_TXREFCLK_RDY_LOW		0
+#define XVPHY_TXREFCLK_RDY_HIGH		1
+#define XHDMIPHY1_TXREFCLK_RDY_LOW		0
+#define XHDMIPHY1_TXREFCLK_RDY_HIGH		1
+
+#define hdmi_mutex_lock(x) mutex_lock(x)
+#define hdmi_mutex_unlock(x) mutex_unlock(x)
+
+/* TX Subsystem Sub-core offsets */
+#define TXSS_TX_OFFSET				0x00000u
+#define TXSS_VTC_OFFSET				0x10000u
+#define TXSS_HDCP14_OFFSET			0x20000u
+#define TXSS_HDCP14_TIMER_OFFSET	0x30000u
+#define TXSS_HDCP22_OFFSET			0x40000u
+/* HDCP22 sub-core offsets */
+#define TX_HDCP22_CIPHER_OFFSET		0x00000u
+#define TX_HDCP22_TIMER_OFFSET		0x10000u
+#define TX_HDCP22_RNG_OFFSET		0x20000u
+/* Tx subsystem video interface */
+#define XHDMI_AXI_STREAM		0
+#define XHDMI_NATIVE_VIDEO		1
+#define XHDMI_NATIVE_VIDEO_VDE		2
+/** HDMI 2.0 suppors minimum resolution of 640x480 and
+ *  maximum resolution of 4096x2160. VPSS scaling values
+ *  should be configured accordingly.
+ */
+#define XHDMI_VPSS_MIN_WIDTH		640
+#define XHDMI_VPSS_MIN_HEIGHT		480
+#define XHDMI_VPSS_MAX_WIDTH		4096
+#define XHDMI_VPSS_MAX_HEIGHT		2160
+
+/**
+ * struct xlnx_drm_hdmi - Xilinx HDMI core
+ * @encoder: the drm encoder structure
+ * @connector: the drm connector structure
+ * @dev: device structure
+ * @iomem: device I/O memory for register access
+ * @hdcp1x_keymngmt_iomem: hdcp key management block I/O memory for register access
+ * @clk: video clock
+ * @axi_lite_clk: axi_lite clock for register access
+ * @tmds_clk: clock configured per resolution
+ * @retimer_clk: dp159 (retimer) clock
+ * @irq: hdmi subsystem irq
+ * @hdcp1x_irq;: hdcp14 block irq
+ * @hdcp1x_timer_irq: hdcp1.4 timer irq
+ * @hdcp22_irq: hdcp2.2 block irq
+ * @hdcp22_timer_irq: hdcp2.2 time irq
+ * @hdcp_authenticate: flag to enable/disable hdcp authentication
+ * @hdcp_encrypt: flag to enable/disable encryption
+ * @hdcp_protect: flag to prevent hdcp in pass-throuch mode
+ * @hdcp_authenticated: authentication state flag
+ * @hdcp_encrypted: ecryption state flag
+ * @hdcp_password_accepted: flag to denote is user pwd was accepted
+ * @delayed_work_hdcp_poll: work queue for hdcp polling
+ * @hdcp_auth_counter: counter to control hdcp poll time
+ * @teardown: flag to indicate driver is being unloaded
+ * @phy: PHY handle for hdmi lanes
+ * @hdmi_mutex: mutex to lock hdmi structure
+ * @irq_lock: to lock irq handler
+ * @cable_connected: flag to indicate cable state
+ * @hdmi_stream_up: flag to inidcate video stream state
+ * @have_edid: flag to indicate if edid is available
+ * @is_hdmi_20_sink: flag to indicate if sink is hdmi2.0 capable
+ * @dpms: current dpms state
+ * @xvidc_colorfmt: hdmi ip internal colorformat representation
+ * @config: IP configuration structure
+ * @xv_hdmitxss: IP low level driver structure
+ * @IntrStatus: Flag to indicate irq status
+ * @xvphy: pointer to xilinx video phy
+ * @xgtphy: pointer to Xilinx HDMI GT Controller phy
+ * @isvphy: Flag to determine which Phy
+ * @wait_for_streamup: Flag for TxStreamUpCallback done
+ * @wait_event: Wait event queue for TxStreamUpCallback
+ * @audio_enabled: flag to indicate audio is enabled in device tree
+ * @audio_init: flag to indicate audio is initialized
+ * @tx_audio_data: audio data to be shared with audio module
+ * @bridge: bridge structure
+ * @height_out: configurable bridge output height parameter
+ * @height_out_prop_val: configurable bridge output height parameter value
+ * @width_out: configurable bridge output width parameter
+ * @width_out_prop_val: configurable bridge output width parameter value
+ * @in_fmt: configurable bridge input media format
+ * @in_fmt_prop_val: configurable media bus format value
+ * @out_fmt: configurable bridge output media format
+ * @out_fmt_prop_val: configurable media bus format value
+ * @aspect_ratio: configurable aspect ratio parameter
+ * @aspect_ratio_prop_val: configurable aspect ratio value
+ */
+struct xlnx_drm_hdmi {
+	struct drm_encoder encoder;
+	struct drm_connector connector;
+	struct device *dev;
+	void __iomem *iomem;
+	void __iomem *hdcp1x_keymngmt_iomem;
+	/* video streaming bus clock */
+	struct clk *clk;
+	struct clk *axi_lite_clk;
+	/* tmds clock for output res */
+	struct clk *tmds_clk;
+	/* retimer that we configure by setting a clock rate */
+	struct clk *retimer_clk;
+
+	/* HDMI TXSS interrupt */
+	int irq;
+	/* HDCP interrupts  */
+	int hdcp1x_irq;
+	int hdcp1x_timer_irq;
+	int hdcp22_irq;
+	int hdcp22_timer_irq;
+	/* controls */
+	bool hdcp_authenticate;
+	bool hdcp_encrypt;
+	bool hdcp_protect;
+	/* status */
+	bool hdcp_authenticated;
+	bool hdcp_encrypted;
+	bool hdcp_password_accepted;
+	/* delayed work to drive HDCP poll */
+	struct delayed_work delayed_work_hdcp_poll;
+	int hdcp_auth_counter;
+
+	bool teardown;
+
+	struct phy *phy[HDMI_MAX_LANES];
+
+	/* mutex to prevent concurrent access to this structure */
+	struct mutex hdmi_mutex;
+	/* protects concurrent access from interrupt context */
+	spinlock_t irq_lock;
+
+	bool cable_connected;
+	bool hdmi_stream_up;
+	bool have_edid;
+	bool is_hdmi_20_sink;
+	int dpms;
+
+	XVidC_ColorFormat xvidc_colorfmt;
+	XVidC_ColorDepth xvidc_colordepth;
+	/* configuration for the baseline subsystem driver instance */
+	XV_HdmiTxSs_Config config;
+	/* bookkeeping for the baseline subsystem driver instance */
+	XV_HdmiTxSs xv_hdmitxss;
+	/* sub core interrupt status registers */
+	u32 IntrStatus;
+	/* pointer to xvphy */
+	XVphy *xvphy;
+	/* pointer to xgtphy */
+	XHdmiphy1 *xgtphy;
+	/* flag to determine which Phy */
+	u32 isvphy;
+
+	/* flag for waiting till TxStreamUpCallback ends */
+	u32 wait_for_streamup:1;
+	/* Queue to wait on event of TxStreamUpCallback */
+	wait_queue_head_t wait_event;
+
+	/* HDCP keys */
+	u8 hdcp_password[32];
+	u8 Hdcp22Lc128[16];
+	u8 Hdcp22PrivateKey[902];
+	u8 Hdcp14KeyA[328];
+	u8 Hdcp14KeyB[328];
+	bool audio_enabled;
+	bool audio_init;
+	struct xlnx_hdmitx_audio_data *tx_audio_data;
+	struct xlnx_bridge *bridge;
+	struct drm_property *height_out;
+	u32 height_out_prop_val;
+	struct drm_property *width_out;
+	u32 width_out_prop_val;
+	struct drm_property *in_fmt;
+	u32 in_fmt_prop_val;
+	struct drm_property *out_fmt;
+	u32 out_fmt_prop_val;
+	struct drm_property *aspect_ratio;
+	u32 aspect_ratio_prop_val;
+	/*
+	 * Map of v4l2_hdmi_rx_colorimetry.
+	 * AVI infoframe values are derived in driver reverse of how the
+	 * values are populated for v4l2.
+	 */
+	struct drm_property *colorspace;
+	u32 colorspace_val;
+	struct drm_property *ycbcr_enc;
+	u32 ycbcr_enc_val;
+	struct drm_property *xfer_func;
+	u32 xfer_func_val;
+	struct drm_property *quantization;
+	enum hdmi_quantization_range quantization_val;
+};
+
+static const u8 Hdcp22Srm[] = {
+  0x91, 0x00, 0x00, 0x01, 0x01, 0x00, 0x01, 0x87, 0x00, 0x00, 0x00, 0x00, 0x8B, 0xBE, 0x2D, 0x46,
+  0x05, 0x9F, 0x00, 0x78, 0x7B, 0xF2, 0x84, 0x79, 0x7F, 0xC4, 0xF5, 0xF6, 0xC4, 0x06, 0x36, 0xA1,
+  0x20, 0x2E, 0x57, 0xEC, 0x8C, 0xA6, 0x5C, 0xF0, 0x3A, 0x14, 0x38, 0xF0, 0xB7, 0xE3, 0x68, 0xF8,
+  0xB3, 0x64, 0x22, 0x55, 0x6B, 0x3E, 0xA9, 0xA8, 0x08, 0x24, 0x86, 0x55, 0x3E, 0x20, 0x0A, 0xDB,
+  0x0E, 0x5F, 0x4F, 0xD5, 0x0F, 0x33, 0x52, 0x01, 0xF3, 0x62, 0x54, 0x40, 0xF3, 0x43, 0x0C, 0xFA,
+  0xCD, 0x98, 0x1B, 0xA8, 0xB3, 0x77, 0xB7, 0xF8, 0xFA, 0xF7, 0x4D, 0x71, 0xFB, 0xB5, 0xBF, 0x98,
+  0x9F, 0x1A, 0x1E, 0x2F, 0xF2, 0xBA, 0x80, 0xAD, 0x20, 0xB5, 0x08, 0xBA, 0xF6, 0xB5, 0x08, 0x08,
+  0xCF, 0xBA, 0x49, 0x8D, 0xA5, 0x73, 0xD5, 0xDE, 0x2B, 0xEA, 0x07, 0x58, 0xA8, 0x08, 0x05, 0x66,
+  0xB8, 0xD5, 0x2B, 0x9C, 0x0B, 0x32, 0xF6, 0x5A, 0x61, 0xE4, 0x9B, 0xC2, 0xF6, 0xD1, 0xF6, 0x2D,
+  0x0C, 0x19, 0x06, 0x0E, 0x3E, 0xCE, 0x62, 0x97, 0x80, 0xFC, 0x50, 0x56, 0x15, 0xCB, 0xE1, 0xC7,
+  0x23, 0x4B, 0x52, 0x34, 0xC0, 0x9F, 0x85, 0xEA, 0xA9, 0x15, 0x8C, 0xDD, 0x7C, 0x78, 0xD6, 0xAD,
+  0x1B, 0xB8, 0x28, 0x1F, 0x50, 0xD4, 0xD5, 0x42, 0x29, 0xEC, 0xDC, 0xB9, 0xA1, 0xF4, 0x26, 0xFA,
+  0x43, 0xCC, 0xCC, 0xE7, 0xEA, 0xA5, 0xD1, 0x76, 0x4C, 0xDD, 0x92, 0x9B, 0x1B, 0x1E, 0x07, 0x89,
+  0x33, 0xFE, 0xD2, 0x35, 0x2E, 0x21, 0xDB, 0xF0, 0x31, 0x8A, 0x52, 0xC7, 0x1B, 0x81, 0x2E, 0x43,
+  0xF6, 0x59, 0xE4, 0xAD, 0x9C, 0xDB, 0x1E, 0x80, 0x4C, 0x8D, 0x3D, 0x9C, 0xC8, 0x2D, 0x96, 0x23,
+  0x2E, 0x7C, 0x14, 0x13, 0xEF, 0x4D, 0x57, 0xA2, 0x64, 0xDB, 0x33, 0xF8, 0xA9, 0x10, 0x56, 0xF4,
+  0x59, 0x87, 0x43, 0xCA, 0xFC, 0x54, 0xEA, 0x2B, 0x46, 0x7F, 0x8A, 0x32, 0x86, 0x25, 0x9B, 0x2D,
+  0x54, 0xC0, 0xF2, 0xEF, 0x8F, 0xE7, 0xCC, 0xFD, 0x5A, 0xB3, 0x3C, 0x4C, 0xBC, 0x51, 0x89, 0x4F,
+  0x41, 0x20, 0x7E, 0xF3, 0x2A, 0x90, 0x49, 0x5A, 0xED, 0x3C, 0x8B, 0x3D, 0x9E, 0xF7, 0xC1, 0xA8,
+  0x21, 0x99, 0xCF, 0x20, 0xCC, 0x17, 0xFC, 0xC7, 0xB6, 0x5F, 0xCE, 0xB3, 0x75, 0xB5, 0x27, 0x76,
+  0xCA, 0x90, 0x99, 0x2F, 0x80, 0x98, 0x9B, 0x19, 0x21, 0x6D, 0x53, 0x7E, 0x1E, 0xB9, 0xE6, 0xF3,
+  0xFD, 0xCB, 0x69, 0x0B, 0x10, 0xD6, 0x2A, 0xB0, 0x10, 0x5B, 0x43, 0x47, 0x11, 0xA4, 0x60, 0x28,
+  0x77, 0x1D, 0xB4, 0xB2, 0xC8, 0x22, 0xDB, 0x74, 0x3E, 0x64, 0x9D, 0xA8, 0xD9, 0xAA, 0xEA, 0xFC,
+  0xA8, 0xA5, 0xA7, 0xD0, 0x06, 0x88, 0xBB, 0xD7, 0x35, 0x4D, 0xDA, 0xC0, 0xB2, 0x11, 0x2B, 0xFA,
+  0xED, 0xBF, 0x2A, 0x34, 0xED, 0xA4, 0x30, 0x7E, 0xFD, 0xC5, 0x21, 0xB6
+};
+
+static inline struct xlnx_drm_hdmi *encoder_to_hdmi(struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct xlnx_drm_hdmi, encoder);
+}
+
+static inline struct xlnx_drm_hdmi *connector_to_hdmi(struct drm_connector *connector)
+{
+	return container_of(connector, struct xlnx_drm_hdmi, connector);
+}
+
+
+void HdmiTx_PioIntrHandler(XV_HdmiTx *InstancePtr);
+
+static void XV_HdmiTxSs_IntrEnable(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+	XV_HdmiTx_PioIntrEnable(HdmiTxSsPtr->HdmiTxPtr);
+}
+
+static void XV_HdmiTxSs_IntrDisable(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+	XV_HdmiTx_PioIntrDisable(HdmiTxSsPtr->HdmiTxPtr);
+}
+
+static int __maybe_unused hdmitx_pm_suspend(struct device *dev)
+{
+	unsigned long flags;
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	dev_dbg(xhdmi->dev,"HDMI TX suspend function called\n");
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiTxSs_IntrDisable(HdmiTxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+	return 0;
+}
+
+static int __maybe_unused hdmitx_pm_resume(struct device *dev)
+{
+	unsigned long flags;
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	dev_dbg(xhdmi->dev,"HDMI TX resume function called\n");
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiTxSs_IntrEnable(HdmiTxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+	return 0;
+}
+
+/* XV_HdmiTx_IntrHandler */
+static irqreturn_t hdmitx_irq_handler(int irq, void *dev_id)
+{
+	struct xlnx_drm_hdmi *xhdmi;
+
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	unsigned long flags;
+
+	xhdmi = (struct xlnx_drm_hdmi *)dev_id;
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	if (HdmiTxSsPtr->IsReady != XIL_COMPONENT_IS_READY) {
+		dev_dbg(xhdmi->dev, "hdmitx_irq_handler(): HDMI TX SS is not initialized?!\n");
+	}
+
+	/* read status registers */
+	xhdmi->IntrStatus = XV_HdmiTx_ReadReg(HdmiTxSsPtr->HdmiTxPtr->Config.BaseAddress, (
+							XV_HDMITX_PIO_STA_OFFSET)) & (XV_HDMITX_PIO_STA_IRQ_MASK);
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	/* mask interrupt request */
+	XV_HdmiTxSs_IntrDisable(HdmiTxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* call bottom-half */
+	return IRQ_WAKE_THREAD;
+}
+
+/* (struct xlnx_drm_hdmi *)dev_id */
+static irqreturn_t hdmitx_irq_thread(int irq, void *dev_id)
+{
+	struct xlnx_drm_hdmi *xhdmi;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	unsigned long flags;
+
+	xhdmi = (struct xlnx_drm_hdmi *)dev_id;
+	if (!xhdmi) {
+		dev_dbg(xhdmi->dev, "irq_thread: !dev_id\n");
+		return IRQ_HANDLED;
+	}
+	/* driver is being torn down, do not process further interrupts */
+	if (xhdmi->teardown) {
+		dev_dbg(xhdmi->dev, "irq_thread: teardown\n");
+		return IRQ_HANDLED;
+	}
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+
+	/* call baremetal interrupt handler, this in turn will
+	 * call the registed callbacks functions */
+	if (xhdmi->IntrStatus) HdmiTx_PioIntrHandler(HdmiTxSsPtr->HdmiTxPtr);
+
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	/* unmask interrupt request */
+	XV_HdmiTxSs_IntrEnable(HdmiTxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+/* top-half interrupt handler for HDMI TX HDCP */
+static irqreturn_t hdmitx_hdcp_irq_handler(int irq, void *dev_id)
+{
+	struct xlnx_drm_hdmi *xhdmi;
+
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	unsigned long flags;
+
+	xhdmi = (struct xlnx_drm_hdmi *)dev_id;
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	/* mask/disable interrupt requests */
+	if (irq == xhdmi->hdcp1x_irq) {
+	  XHdcp1x_WriteReg(HdmiTxSsPtr->Hdcp14Ptr->Config.BaseAddress,
+		  XHDCP1X_CIPHER_REG_INTERRUPT_MASK, (u32)0xFFFFFFFFu);
+	} else if (irq == xhdmi->hdcp1x_timer_irq) {
+	  XTmrCtr_DisableIntr(HdmiTxSsPtr->HdcpTimerPtr->BaseAddress, 0);
+	} else if (irq == xhdmi->hdcp22_timer_irq) {
+	  XTmrCtr_DisableIntr(HdmiTxSsPtr->Hdcp22Ptr->Timer.TmrCtr.BaseAddress, 0);
+	  XTmrCtr_DisableIntr(HdmiTxSsPtr->Hdcp22Ptr->Timer.TmrCtr.BaseAddress, 1);
+	}
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* call bottom-half */
+	return IRQ_WAKE_THREAD;
+}
+
+/* HDCP service routine, runs outside of interrupt context and can sleep and takes mutexes */
+static irqreturn_t hdmitx_hdcp_irq_thread(int irq, void *dev_id)
+{
+	struct xlnx_drm_hdmi *xhdmi;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	unsigned long flags;
+
+	xhdmi = (struct xlnx_drm_hdmi *)dev_id;
+	if (!xhdmi) {
+		dev_dbg(xhdmi->dev, "irq_thread: !dev_id\n");
+		return IRQ_HANDLED;
+	}
+	/* driver is being torn down, do not process further interrupts */
+	if (xhdmi->teardown) {
+		dev_dbg(xhdmi->dev, "irq_thread: teardown\n");
+		return IRQ_HANDLED;
+	}
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	/* invoke the bare-metal interrupt handler under mutex lock */
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	if (irq == xhdmi->hdcp1x_irq) {
+		XV_HdmiTxSS_HdcpIntrHandler(HdmiTxSsPtr);
+	} else if (irq == xhdmi->hdcp1x_timer_irq) {
+		XV_HdmiTxSS_HdcpTimerIntrHandler(HdmiTxSsPtr);
+	} else if (irq == xhdmi->hdcp22_timer_irq) {
+		XV_HdmiTxSS_Hdcp22TimerIntrHandler(HdmiTxSsPtr);
+	}
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+
+	/* re-enable interrupt requests */
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	if (irq == xhdmi->hdcp1x_irq) {
+		XHdcp1x_WriteReg(HdmiTxSsPtr->Hdcp14Ptr->Config.BaseAddress,
+			XHDCP1X_CIPHER_REG_INTERRUPT_MASK, (u32)0xFFFFFFFDu);
+	} else if (irq == xhdmi->hdcp1x_timer_irq) {
+		XTmrCtr_EnableIntr(HdmiTxSsPtr->HdcpTimerPtr->BaseAddress, 0);
+	} else if (irq == xhdmi->hdcp22_timer_irq) {
+		XTmrCtr_EnableIntr(HdmiTxSsPtr->Hdcp22Ptr->Timer.TmrCtr.BaseAddress, 0);
+		XTmrCtr_EnableIntr(HdmiTxSsPtr->Hdcp22Ptr->Timer.TmrCtr.BaseAddress, 1);
+	}
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static void hdcp_protect_content(struct xlnx_drm_hdmi *xhdmi)
+{
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	if (!XV_HdmiTxSs_HdcpIsReady(HdmiTxSsPtr)) return;
+	/* content must be protected but is not encrypted? */
+	if (xhdmi->hdcp_protect && (!xhdmi->hdcp_encrypted)) {
+		/* blank content instead of encrypting */
+		XV_HdmiTxSs_HdcpEnableBlank(HdmiTxSsPtr);
+	} else {
+		/* do not blank content; either no protection required or already encrypted */
+		XV_HdmiTxSs_HdcpDisableBlank(HdmiTxSsPtr);
+	}
+}
+
+static void XHdcp_Authenticate(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+	if (!XV_HdmiTxSs_HdcpIsReady(HdmiTxSsPtr)) return;
+	if (XV_HdmiTxSs_IsStreamUp(HdmiTxSsPtr)) {
+		/* Trigger authentication on Idle */
+		if (!(XV_HdmiTxSs_HdcpIsAuthenticated(HdmiTxSsPtr)) &&
+			!(XV_HdmiTxSs_HdcpIsInProgress(HdmiTxSsPtr))) {
+			XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_AUTHENTICATE_EVT);
+		}
+		/* Trigger authentication on Toggle */
+		else if (XV_HdmiTxSs_IsStreamToggled(HdmiTxSsPtr)) {
+			XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_AUTHENTICATE_EVT);
+		}
+	}
+}
+
+// Send Vendor Specific InfoFrame
+static void SendVSInfoframe(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+	XHdmiC_VSIF *VSIFPtr;
+	XHdmiC_Aux Aux;
+
+	VSIFPtr = XV_HdmiTxSs_GetVSIF(HdmiTxSsPtr);
+
+	(void)memset((void *)VSIFPtr, 0, sizeof(XHdmiC_VSIF));
+	(void)memset((void *)&Aux, 0, sizeof(XHdmiC_Aux));
+
+	VSIFPtr->Version = 0x1;
+	VSIFPtr->IEEE_ID = 0xC03;
+
+	if (XVidC_IsStream3D(&(HdmiTxSsPtr->HdmiTxPtr->Stream.Video))) {
+		VSIFPtr->Format = XHDMIC_VSIF_VF_3D;
+		VSIFPtr->Info_3D.Stream = HdmiTxSsPtr->HdmiTxPtr->Stream.Video.Info_3D;
+		VSIFPtr->Info_3D.MetaData.IsPresent = FALSE;
+	} else if (HdmiTxSsPtr->HdmiTxPtr->Stream.Video.VmId == XVIDC_VM_3840x2160_24_P ||
+			   HdmiTxSsPtr->HdmiTxPtr->Stream.Video.VmId == XVIDC_VM_3840x2160_25_P ||
+			   HdmiTxSsPtr->HdmiTxPtr->Stream.Video.VmId == XVIDC_VM_3840x2160_30_P ||
+			   HdmiTxSsPtr->HdmiTxPtr->Stream.Video.VmId == XVIDC_VM_4096x2160_24_P) {
+		VSIFPtr->Format = XHDMIC_VSIF_VF_EXTRES;
+
+		/* Set HDMI VIC */
+		switch(HdmiTxSsPtr->HdmiTxPtr->Stream.Video.VmId) {
+			case XVIDC_VM_4096x2160_24_P :
+				VSIFPtr->HDMI_VIC = 4;
+				break;
+			case XVIDC_VM_3840x2160_24_P :
+				VSIFPtr->HDMI_VIC = 3;
+				break;
+			case XVIDC_VM_3840x2160_25_P :
+				VSIFPtr->HDMI_VIC = 2;
+				break;
+			case XVIDC_VM_3840x2160_30_P :
+				VSIFPtr->HDMI_VIC = 1;
+				break;
+			default :
+				break;
+		}
+	} else {
+		VSIFPtr->Format = XHDMIC_VSIF_VF_NOINFO;
+	}
+
+	Aux = XV_HdmiC_VSIF_GeneratePacket(VSIFPtr);
+
+	XV_HdmiTxSs_SendGenericAuxInfoframe(HdmiTxSsPtr, &Aux);
+}
+
+/* Send out all the InfoFrames in the AuxFifo during PassThrough mode
+ * or send out AVI, Audio, Vendor Specific InfoFrames.
+ */
+static void SendInfoframe(XV_HdmiTxSs *HdmiTxSsPtr)
+{
+	XHdmiC_AVI_InfoFrame *AviInfoFramePtr;
+	XHdmiC_Aux AuxFifo;
+
+	AviInfoFramePtr = XV_HdmiTxSs_GetAviInfoframe(HdmiTxSsPtr);
+
+	// Generate Aux from the current TX InfoFrame
+	AuxFifo = XV_HdmiC_AVIIF_GeneratePacket(AviInfoFramePtr);
+	XV_HdmiTxSs_SendGenericAuxInfoframe(HdmiTxSsPtr, &AuxFifo);
+
+	/* GCP does not need to be sent out because GCP packets on the TX side is
+	   handled by the HDMI TX core fully. */
+
+	SendVSInfoframe(HdmiTxSsPtr);
+}
+
+static void TxToggleCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	dev_dbg(xhdmi->dev,"%s()\n", __func__);
+	XV_HdmiTxSs_StreamStart(HdmiTxSsPtr);
+	if (XV_HdmiTxSs_HdcpIsReady(HdmiTxSsPtr) && xhdmi->hdcp_authenticate) {
+		XHdcp_Authenticate(HdmiTxSsPtr);
+	}
+}
+
+static void TxConnectCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+	XVphy *VphyPtr = xhdmi->xvphy;
+	XHdmiphy1 *XGtPhyPtr = xhdmi->xgtphy;
+
+	dev_dbg(xhdmi->dev,"%s()\n", __func__);
+	xvphy_mutex_lock(xhdmi->phy[0]);
+	if (HdmiTxSsPtr->IsStreamConnected) {
+		int xst_hdmi20;
+		xhdmi->cable_connected = 1;
+		xhdmi->connector.status = connector_status_connected;
+		/* Check HDMI sink version */
+		xst_hdmi20 = XV_HdmiTxSs_DetectHdmi20(HdmiTxSsPtr);
+		dev_dbg(xhdmi->dev,"TxConnectCallback(): TX connected to HDMI %s Sink Device\n",
+			(xst_hdmi20 == XST_SUCCESS)? "2.0": "1.4");
+		xhdmi->is_hdmi_20_sink = (xst_hdmi20 == XST_SUCCESS);
+		if (xhdmi->isvphy)
+			XVphy_IBufDsEnable(VphyPtr, 0, XVPHY_DIR_TX, (TRUE));
+		else
+			XHdmiphy1_IBufDsEnable(XGtPhyPtr, 0, XHDMIPHY1_DIR_TX, (TRUE));
+		XV_HdmiTxSs_StreamStart(HdmiTxSsPtr);
+		/* stream never goes down on disconnect. Force hdcp event */
+		if (xhdmi->hdmi_stream_up &&
+			XV_HdmiTxSs_HdcpIsReady(HdmiTxSsPtr) &&
+			xhdmi->hdcp_authenticate) {
+			/* Push the Authenticate event to the HDCP event queue */
+			XV_HdmiTxSs_HdcpPushEvent(HdmiTxSsPtr, XV_HDMITXSS_HDCP_AUTHENTICATE_EVT);
+		}
+	}
+	else {
+		dev_dbg(xhdmi->dev,"TxConnectCallback(): TX disconnected\n");
+		xhdmi->cable_connected = 0;
+		xhdmi->connector.status = connector_status_disconnected;
+		xhdmi->have_edid = 0;
+		xhdmi->is_hdmi_20_sink = 0;
+		/* do not disable ibufds - stream will not go down*/
+		if (xhdmi->isvphy)
+			XVphy_IBufDsEnable(VphyPtr, 0, XVPHY_DIR_TX, (FALSE));
+		else
+			XHdmiphy1_IBufDsEnable(XGtPhyPtr, 0, XHDMIPHY1_DIR_TX, (FALSE));
+	}
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+
+	if(xhdmi->connector.dev) {
+		/* Not using drm_kms_helper_hotplug_event because apart from notifying
+		 * user space about hotplug, it also calls output_poll_changed of drm device
+		 * that is used to inform the fbdev helper of output changes. It is of no use
+		 * here. Sometimes there were hang issue while running the application
+		 * on using drm_kms_helper_hotplug_event API. */
+		drm_sysfs_hotplug_event(xhdmi->connector.dev);
+		//drm_kms_helper_hotplug_event(xhdmi->drm_dev);
+		dev_dbg(xhdmi->dev,"Hotplug event sent to user space, Connect = %d", xhdmi->connector.status);
+	} else {
+		printk(KERN_WARNING "Not sending HOTPLUG event because "
+				"drm device is NULL as drm_connector_init is not called yet.\n");
+	}
+
+	dev_dbg(xhdmi->dev,"TxConnectCallback() done\n");
+}
+
+static void TxStreamUpCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	XVphy_PllType TxPllType;
+	XHdmiphy1_PllType GtTxPllType;
+	u64 TxLineRate = 0;
+	XHdmiC_AVI_InfoFrame *AVIInfoFramePtr;
+	XVidC_VideoStream *HdmiTxSsVidStreamPtr;
+
+	HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	VphyPtr = xhdmi->xvphy;
+	XGtPhyPtr = xhdmi->xgtphy;
+
+	dev_dbg(xhdmi->dev,"TxStreamUpCallback(): TX stream is up\n");
+	/* Ensure that the bridge SYSRST is not released */
+	XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, TRUE);
+	xhdmi->hdmi_stream_up = 1;
+
+	AVIInfoFramePtr = XV_HdmiTxSs_GetAviInfoframe(HdmiTxSsPtr);
+	HdmiTxSsVidStreamPtr = XV_HdmiTxSs_GetVideoStream(HdmiTxSsPtr);
+	if ( (HdmiTxSsVidStreamPtr->VmId == XVIDC_VM_1440x480_60_I) ||
+		 (HdmiTxSsVidStreamPtr->VmId == XVIDC_VM_1440x576_50_I) ) {
+		AVIInfoFramePtr->PixelRepetition =
+				XHDMIC_PIXEL_REPETITION_FACTOR_2;
+		dev_dbg(xhdmi->dev,"Pixel repetition set to 2\n");
+	} else {
+		AVIInfoFramePtr->PixelRepetition =
+				XHDMIC_PIXEL_REPETITION_FACTOR_1;
+		dev_dbg(xhdmi->dev,"Pixel repetition set to 1\n");
+	}
+
+	xvphy_mutex_lock(xhdmi->phy[0]);
+	if (xhdmi->isvphy) {
+		TxPllType = XVphy_GetPllType(VphyPtr, 0, XVPHY_DIR_TX, XVPHY_CHANNEL_ID_CH1);
+		if ((TxPllType == XVPHY_PLL_TYPE_CPLL)) {
+			TxLineRate = XVphy_GetLineRateHz(VphyPtr, 0, XVPHY_CHANNEL_ID_CH1);
+		}
+		else if((TxPllType == XVPHY_PLL_TYPE_QPLL) ||
+			(TxPllType == XVPHY_PLL_TYPE_QPLL0) ||
+			(TxPllType == XVPHY_PLL_TYPE_PLL0)) {
+			TxLineRate = XVphy_GetLineRateHz(VphyPtr, 0, XVPHY_CHANNEL_ID_CMN0);
+		}
+		else {
+			TxLineRate = XVphy_GetLineRateHz(VphyPtr, 0, XVPHY_CHANNEL_ID_CMN1);
+		}
+	} else {
+		GtTxPllType = XHdmiphy1_GetPllType(XGtPhyPtr, 0, XHDMIPHY1_DIR_TX, XHDMIPHY1_CHANNEL_ID_CH1);
+		/* Versal - Implementation different here */
+		if (GtTxPllType == XHDMIPHY1_PLL_TYPE_LCPLL) {
+			TxLineRate =
+				XHdmiphy1_GetLineRateHz(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CMN0);
+			dev_dbg(xhdmi->dev, "GtPhy TxLineRate LCPLL %lld Kbps\r\n",(TxLineRate/1000));
+		} else if (GtTxPllType == XHDMIPHY1_PLL_TYPE_RPLL) {
+			TxLineRate =
+				XHdmiphy1_GetLineRateHz(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CMN1);
+			dev_dbg(xhdmi->dev, "GtPhy TxLineRate RPLL %lld Kbps\r\n",(TxLineRate/1000));
+		} else {
+			dev_err(xhdmi->dev, "GtPhy Error! Invalid GtTxPllType in TxStreamUpCallback.\r\n");
+		}
+	}
+
+	/* configure an external retimer through a (virtual) CCF clock
+	 * (this was tested against the DP159 misc retimer driver) */
+	if (xhdmi->retimer_clk) {
+		dev_dbg(xhdmi->dev,"retimer: clk_set_rate(xhdmi->retimer_clk, TxLineRate=%lld\n", TxLineRate);
+		(void)clk_set_rate(xhdmi->retimer_clk, (signed long long)TxLineRate);
+	}
+	/* Copy Sampling Rate */
+	if (xhdmi->isvphy)
+		XV_HdmiTxSs_SetSamplingRate(HdmiTxSsPtr, VphyPtr->HdmiTxSampleRate);
+	else
+		XV_HdmiTxSs_SetSamplingRate(HdmiTxSsPtr, XGtPhyPtr->HdmiTxSampleRate);
+
+	/* Enable TX TMDS clock*/
+	if (xhdmi->isvphy)
+		XVphy_Clkout1OBufTdsEnable(VphyPtr, XVPHY_DIR_TX, (TRUE));
+	else
+		XHdmiphy1_Clkout1OBufTdsEnable(XGtPhyPtr, XHDMIPHY1_DIR_TX, (TRUE));
+
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+
+#ifdef DEBUG
+	XV_HdmiTx_DebugInfo(HdmiTxSsPtr->HdmiTxPtr);
+#endif
+	if (xhdmi->hdcp_authenticate) {
+		XHdcp_Authenticate(HdmiTxSsPtr);
+	}
+
+	/* Enable Audio */
+	if (xhdmi->audio_enabled) {
+		XV_HdmiTxSs_AudioMute(HdmiTxSsPtr, 0);
+	}
+
+	/* Check if Link Ready and Video Ready bits are set in PIO_IN register */
+	if ((XV_HDMITX_PIO_IN_VID_RDY_MASK | XV_HDMITX_PIO_IN_LNK_RDY_MASK) &&
+			XV_HdmiTx_ReadReg((uintptr_t)xhdmi->iomem,
+					XV_HDMITX_PIO_IN_OFFSET)) {
+		xhdmi->wait_for_streamup = 1;
+	} else {
+		xhdmi->wait_for_streamup = 0;
+	}
+
+	wake_up(&xhdmi->wait_event);
+
+	/* When YUYV is base color format for pl display then HDMI doesn't come up
+	 * first couple of tries as the EXT_SYSRST (bit 22) is cleared.
+	 * Set this bit in case stream is up and encoder is enabled
+	 */
+	if (xhdmi->dpms == DRM_MODE_DPMS_ON && HdmiTxSsPtr->HdmiTxPtr->Stream.IsConnected)
+		XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, FALSE);
+
+	dev_dbg(xhdmi->dev,"TxStreamUpCallback(): done\n");
+}
+
+static void TxStreamDownCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+
+	dev_dbg(xhdmi->dev,"TxStreamDownCallback(): TX stream is down\n\r");
+	xhdmi->hdmi_stream_up = 0;
+
+	xhdmi->hdcp_authenticated = 0;
+	xhdmi->hdcp_encrypted = 0;
+	hdcp_protect_content(xhdmi);
+}
+
+static void TxVsCallback(void *CallbackRef)
+{
+	XHdmiC_Aux aud_aux_fifo;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+	struct hdmi_drm_infoframe frame;
+	struct v4l2_hdr10_payload *DRMInfoFramePtr =
+				XV_HdmiTxSs_GetDrmInfoframe(HdmiTxSsPtr);
+	XHdmiC_Aux hdr_aux_fifo;
+	struct drm_connector_state *state = xhdmi->connector.state;
+
+	/* Send NULL Aux packet */
+	SendInfoframe(HdmiTxSsPtr);
+
+	if (xhdmi->audio_init) {
+		aud_aux_fifo.Header.Byte[0] = xhdmi->tx_audio_data->buffer[0];
+		aud_aux_fifo.Header.Byte[1] = xhdmi->tx_audio_data->buffer[1];
+		aud_aux_fifo.Header.Byte[2] = xhdmi->tx_audio_data->buffer[2];
+		aud_aux_fifo.Header.Byte[3] = 0;
+
+		aud_aux_fifo.Data.Byte[0] = xhdmi->tx_audio_data->buffer[3];
+		aud_aux_fifo.Data.Byte[1] = xhdmi->tx_audio_data->buffer[4];
+		aud_aux_fifo.Data.Byte[2] = xhdmi->tx_audio_data->buffer[5];
+		aud_aux_fifo.Data.Byte[3] = xhdmi->tx_audio_data->buffer[6];
+		aud_aux_fifo.Data.Byte[4] = xhdmi->tx_audio_data->buffer[7];
+		aud_aux_fifo.Data.Byte[5] = xhdmi->tx_audio_data->buffer[8];
+
+		XV_HdmiTxSs_SendGenericAuxInfoframe(HdmiTxSsPtr,
+							&aud_aux_fifo);
+	}
+
+	if (!state || !state->gen_hdr_output_metadata)
+		return;
+
+	drm_hdmi_infoframe_set_gen_hdr_metadata(&frame, state);
+	/* hdmi_drm_infoframe to v4l2_hdr10_payload */
+	DRMInfoFramePtr->eotf = (__u8) frame.eotf;
+	DRMInfoFramePtr->metadata_type = (__u8) frame.metadata_type;
+	DRMInfoFramePtr->display_primaries[0].x =
+				(__u16) frame.display_primaries[0].x;
+	DRMInfoFramePtr->display_primaries[0].y =
+				(__u16) frame.display_primaries[0].y;
+	DRMInfoFramePtr->display_primaries[1].x =
+				(__u16) frame.display_primaries[1].x;
+	DRMInfoFramePtr->display_primaries[1].y =
+				(__u16) frame.display_primaries[1].y;
+	DRMInfoFramePtr->display_primaries[2].x =
+				(__u16) frame.display_primaries[2].x;
+	DRMInfoFramePtr->display_primaries[2].y =
+				(__u16) frame.display_primaries[2].y;
+	DRMInfoFramePtr->white_point.x = (__u16) frame.white_point.x;
+	DRMInfoFramePtr->white_point.y = (__u16) frame.white_point.y;
+	DRMInfoFramePtr->max_mdl =
+				(__u16) frame.max_display_mastering_luminance;
+	DRMInfoFramePtr->min_mdl =
+				(__u16) frame.min_display_mastering_luminance;
+	DRMInfoFramePtr->max_cll = (__u16) frame.max_cll;
+	DRMInfoFramePtr->max_fall = (__u16) frame.max_fall;
+
+	XV_HdmiC_DRMIF_GeneratePacket(DRMInfoFramePtr, &hdr_aux_fifo);
+	XV_HdmiTxSs_SendGenericAuxInfoframe(HdmiTxSsPtr, &hdr_aux_fifo);
+}
+
+void TxBrdgUnlockedCallback(void *CallbackRef)
+{
+	/* When video out bridge lost lock, reset TPG */
+	/* ResetTpg();                                */
+	/* Config and Run the TPG                     */
+	/* XV_ConfigTpg(&Tpg);                        */
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	dev_dbg(xhdmi->dev,"TX Bridge Unlocked Callback\r\n");
+}
+
+void TxBrdgOverflowCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	dev_dbg(xhdmi->dev,"TX Video Bridge Overflow\r\n");
+}
+
+void TxBrdgUnderflowCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	dev_dbg(xhdmi->dev,"TX Video Bridge Underflow\r\n");
+}
+
+void TxHdcpAuthenticatedCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	xhdmi->hdcp_authenticated = 1;
+	if (XV_HdmiTxSs_HdcpGetProtocol(HdmiTxSsPtr) == XV_HDMITXSS_HDCP_22) {
+		dev_dbg(xhdmi->dev,"HDCP 2.2 TX authenticated.\n");
+	}
+
+	else if (XV_HdmiTxSs_HdcpGetProtocol(HdmiTxSsPtr) == XV_HDMITXSS_HDCP_14) {
+		dev_dbg(xhdmi->dev,"HDCP 1.4 TX authenticated.\n");
+	}
+
+	if (xhdmi->hdcp_encrypt) {
+		dev_dbg(xhdmi->dev,"Enabling Encryption.\n");
+		XV_HdmiTxSs_HdcpEnableEncryption(HdmiTxSsPtr);
+		xhdmi->hdcp_encrypted = 1;
+		hdcp_protect_content(xhdmi);
+	} else {
+		dev_dbg(xhdmi->dev,"Not Enabling Encryption.\n");
+	}
+}
+
+void TxHdcpUnauthenticatedCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+
+	dev_dbg(xhdmi->dev,"TxHdcpUnauthenticatedCallback()\n");
+	xhdmi->hdcp_authenticated = 0;
+	xhdmi->hdcp_encrypted = 0;
+	hdcp_protect_content(xhdmi);
+}
+
+/* entered with vphy mutex taken */
+static void VphyHdmiTxInitCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+
+	HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	dev_dbg(xhdmi->dev,"VphyHdmiTxInitCallback(): XV_HdmiTxSs_RefClockChangeInit()\n");
+
+	/* a pair of mutexes must be locked in fixed order to prevent deadlock,
+	 * and the order is TX SS then XVPHY, so first unlock XVPHY then lock both */
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	xvphy_mutex_lock(xhdmi->phy[0]);
+
+	XV_HdmiTxSs_RefClockChangeInit(HdmiTxSsPtr);
+	/* unlock TX SS mutex but keep XVPHY locked */
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+	dev_dbg(xhdmi->dev,"VphyHdmiTxInitCallback() done\n");
+}
+
+/* entered with vphy mutex taken */
+static void VphyHdmiTxReadyCallback(void *CallbackRef)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)CallbackRef;
+
+	dev_dbg(xhdmi->dev,"VphyHdmiTxReadyCallback(NOP) done\n");
+}
+
+/*
+ * DRM connector functions
+ */
+
+static enum drm_connector_status
+xlnx_drm_hdmi_connector_detect(struct drm_connector *connector, bool force)
+{
+	/* it takes HDMI 50 ms to detect connection on init */
+	static int first_time_ms = 50;
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+	/* first time; wait 50 ms max until cable connected */
+	while (first_time_ms && !xhdmi->cable_connected) {
+		msleep(1);
+		first_time_ms--;
+	}
+	/* connected in less than 50 ms? */
+	if (first_time_ms) {
+		/* do not wait during further connect detects */
+		first_time_ms = 0;
+		/* after first time, report immediately */
+		dev_dbg(xhdmi->dev,"xlnx_drm_hdmi_connector_detect() waited %d ms until connect.\n", 50 - first_time_ms);
+	}
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	/* cable connected  */
+	if (xhdmi->cable_connected) {
+		hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+		dev_dbg(xhdmi->dev, "xlnx_drm_hdmi_connector_detect() = connected\n");
+		return connector_status_connected;
+	}
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+	dev_dbg(xhdmi->dev, "xlnx_drm_hdmi_connector_detect() = disconnected\n");
+	return connector_status_disconnected;
+}
+
+static void xlnx_drm_hdmi_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+	connector->dev = NULL;
+}
+
+static int xlnx_drm_hdmi_set_property(struct drm_connector *connector,
+			     struct drm_connector_state *state,
+			     struct drm_property *property, uint64_t val)
+{
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+
+	if (property == xhdmi->colorspace)
+		xhdmi->colorspace_val = (u32)val;
+	else if (property == xhdmi->ycbcr_enc)
+		xhdmi->ycbcr_enc_val = (u32)val;
+	else if (property == xhdmi->xfer_func)
+		xhdmi->xfer_func_val = (u32)val;
+	else if (property == xhdmi->quantization)
+		xhdmi->quantization_val = (u32)val;
+	else if (property == xhdmi->height_out)
+		xhdmi->height_out_prop_val = (u32)val;
+	else if (property == xhdmi->width_out)
+		xhdmi->width_out_prop_val = (u32)val;
+	else if (property == xhdmi->in_fmt)
+		xhdmi->in_fmt_prop_val = (u32)val;
+	else if (property == xhdmi->out_fmt)
+		xhdmi->out_fmt_prop_val = (u32)val;
+	else if (property == xhdmi->aspect_ratio)
+		xhdmi->aspect_ratio_prop_val = (u32)val;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static int xlnx_drm_hdmi_get_property(struct drm_connector *connector,
+			     const struct drm_connector_state *state,
+			     struct drm_property *property, uint64_t *val)
+{
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+
+	if (property == xhdmi->colorspace)
+		*val = xhdmi->colorspace_val;
+	else if (property == xhdmi->ycbcr_enc)
+		*val = xhdmi->ycbcr_enc_val;
+	else if (property == xhdmi->xfer_func)
+		*val = xhdmi->xfer_func_val;
+	else if (property == xhdmi->quantization)
+		*val = xhdmi->quantization_val;
+	else if (property == xhdmi->height_out)
+		*val = xhdmi->height_out_prop_val;
+	else if (property == xhdmi->width_out)
+		*val = xhdmi->width_out_prop_val;
+	else if (property == xhdmi->in_fmt)
+		*val = xhdmi->in_fmt_prop_val;
+	else if (property == xhdmi->out_fmt)
+		*val = xhdmi->out_fmt_prop_val;
+	else if (property == xhdmi->aspect_ratio)
+		*val = xhdmi->aspect_ratio_prop_val;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct drm_connector_funcs xlnx_drm_hdmi_connector_funcs = {
+//	.dpms			= drm_helper_connector_dpms,
+	.detect			= xlnx_drm_hdmi_connector_detect,
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= xlnx_drm_hdmi_connector_destroy,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_set_property = xlnx_drm_hdmi_set_property,
+	.atomic_get_property = xlnx_drm_hdmi_get_property,
+};
+
+static int xlnx_drm_hdmi_connector_mode_valid(struct drm_connector *connector,
+				    struct drm_display_mode *mode)
+{
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+	int max_rate = 340 * 1000;
+	enum drm_mode_status status = MODE_OK;
+
+	dev_dbg(xhdmi->dev, "%s\n", __func__);
+
+	/* This is done to make the functionality similar as BM code in which the
+	 * timing table has vdisplay value of 540 for 1080i usecase.
+	 * By this change, doing modetest -M xlnx, will give vdisplay 540 instead of
+	 * 1080 */
+	if(mode->flags & DRM_MODE_FLAG_INTERLACE) {
+		mode->vdisplay = mode->vdisplay / 2;
+		dev_dbg(xhdmi->dev, "For DRM_MODE_FLAG_INTERLACE, divide mode->vdisplay %d\n", mode->vdisplay);
+	}
+
+	drm_mode_debug_printmodeline(mode);
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	/* HDMI 2.0 sink connected? */
+	if (xhdmi->is_hdmi_20_sink)
+		max_rate = 600 * 1000;
+	/* pixel clock too high for sink? */
+	if (mode->clock > max_rate)
+		status = MODE_CLOCK_HIGH;
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+	return status;
+}
+
+/* callback function for drm_do_get_edid(), used in xlnx_drm_hdmi_get_modes()
+ * through drm_do_get_edid() from drm/drm_edid.c.
+ *
+ * called with hdmi_mutex taken
+ *
+ * Return 0 on success, !0 otherwise
+ */
+static int xlnx_drm_hdmi_get_edid_block(void *data, u8 *buf, unsigned int block,
+				  size_t len)
+{
+	u8 *buffer;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)data;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	int ret;
+
+	/* out of bounds? */
+	if (((block * 128) + len) > 256) return -EINVAL;
+
+	buffer = kzalloc(256, GFP_KERNEL);
+	if (!buffer) return -ENOMEM;
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	if (!HdmiTxSsPtr->IsStreamConnected) {
+		dev_dbg(xhdmi->dev, "xlnx_drm_hdmi_get_edid_block() stream is not connected\n");
+	}
+	/* first obtain edid in local buffer */
+	ret = XV_HdmiTxSs_ReadEdid(HdmiTxSsPtr, buffer);
+	if (ret == XST_FAILURE) {
+		kfree(buffer);
+		dev_dbg(xhdmi->dev, "xlnx_drm_hdmi_get_edid_block() failed reading EDID\n");
+		return -EINVAL;
+	}
+
+	/* then copy the requested 128-byte block(s) */
+	memcpy(buf, buffer + block * 128, len);
+	/* free our local buffer */
+	kfree(buffer);
+	return 0;
+}
+
+static int xlnx_drm_hdmi_connector_get_modes(struct drm_connector *connector)
+{
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+	struct edid *edid = NULL;
+	int ret;
+	bool is_hdmi_sink;
+
+	dev_dbg(xhdmi->dev, "%s\n", __func__);
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+
+	/* When the I2C adapter connected to the DDC bus is hidden behind a device that
+	 * exposes a different interface to read EDID blocks this function can be used
+	 * to get EDID data using a custom block read function. - from drm_edid.c
+	 */
+
+	/* private data hdmi is passed to xlnx_drm_hdmi_get_edid_block(data, ...) */
+	edid = drm_do_get_edid(connector, xlnx_drm_hdmi_get_edid_block, xhdmi);
+
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+	if (!edid) {
+		xhdmi->have_edid = 0;
+		dev_err(xhdmi->dev, "xlnx_drm_hdmi_get_modes() could not obtain edid, assume <= 1024x768 works.\n");
+		drm_connector_update_edid_property(connector, NULL);
+		return 0;
+	}
+	xhdmi->have_edid = 1;
+
+	/* If the sink is non HDMI, set the stream type to DVI else HDMI */
+	is_hdmi_sink = drm_detect_hdmi_monitor(edid);
+	if(is_hdmi_sink) {
+		XV_HdmiTxSs_SetVideoStreamType(&xhdmi->xv_hdmitxss, 1);
+		dev_dbg(xhdmi->dev, "EDID shows HDMI sink is connected, setting stream type to HDMI\n");
+	} else {
+		XV_HdmiTxSs_SetVideoStreamType(&xhdmi->xv_hdmitxss, 0);
+		dev_dbg(xhdmi->dev, "EDID shows non HDMI sink is connected, setting stream type to DVI\n");
+	}
+
+	drm_connector_update_edid_property(connector, edid);
+	ret = drm_add_edid_modes(connector, edid);
+	kfree(edid);
+	dev_dbg(xhdmi->dev, "xlnx_drm_hdmi_get_modes() done\n");
+	return ret;
+}
+
+static struct drm_encoder *
+xlnx_drm_hdmi_connector_best_encoder(struct drm_connector *connector)
+{
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+
+	return &xhdmi->encoder;
+}
+
+static struct drm_connector_helper_funcs xlnx_drm_hdmi_connector_helper_funcs = {
+	.get_modes		= xlnx_drm_hdmi_connector_get_modes,
+	.best_encoder	= xlnx_drm_hdmi_connector_best_encoder,
+	.mode_valid		= xlnx_drm_hdmi_connector_mode_valid,
+};
+
+/*
+ * DRM encoder functions
+ */
+static void xlnx_drm_hdmi_encoder_dpms(struct drm_encoder *encoder, int dpms)
+{
+	struct xlnx_drm_hdmi *xhdmi = encoder_to_hdmi(encoder);
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	dev_dbg(xhdmi->dev,"xilinx_drm_hdmi_dpms(dpms = %d)\n", dpms);
+
+	if (xhdmi->dpms == dpms) {
+		goto done;
+	}
+
+	xhdmi->dpms = dpms;
+
+	switch (dpms) {
+	case DRM_MODE_DPMS_ON:
+		/* power-up */
+		goto done;
+	default:
+		/* power-down */
+		goto done;
+	}
+done:
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+}
+
+static void xlnx_drm_hdmi_encoder_enable(struct drm_encoder *encoder)
+{
+	struct xlnx_drm_hdmi *xhdmi = encoder_to_hdmi(encoder);
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+	XHdmiphy1 *XGtPhyPtr = xhdmi->xgtphy;
+
+	xlnx_drm_hdmi_encoder_dpms(encoder, DRM_MODE_DPMS_ON);
+	/* Enable the EXT VRST which actually starts the bridge */
+	XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, FALSE);
+
+	if (XGtPhyPtr)
+		XHdmiphy1_TxPllreset(XGtPhyPtr);
+}
+
+static void xlnx_drm_hdmi_encoder_disable(struct drm_encoder *encoder)
+{
+	struct xlnx_drm_hdmi *xhdmi = encoder_to_hdmi(encoder);
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	if (xhdmi->bridge)
+		xlnx_bridge_disable(xhdmi->bridge);
+
+	xlnx_drm_hdmi_encoder_dpms(encoder, DRM_MODE_DPMS_OFF);
+	/* Disable the EXT VRST which actually starts the bridge */
+	XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, TRUE);
+}
+
+static XVidC_ColorFormat hdmitx_find_media_bus(struct xlnx_drm_hdmi *xhdmi,
+					       u32 drm_fourcc)
+{
+	switch(drm_fourcc) {
+
+	case DRM_FORMAT_XBGR8888:
+	case DRM_FORMAT_XRGB8888:
+	case DRM_FORMAT_BGR888:
+	case DRM_FORMAT_RGB888:
+	case DRM_FORMAT_ARGB8888:
+	case DRM_FORMAT_ABGR8888:
+		xhdmi->xvidc_colordepth = XVIDC_BPC_8;
+		return XVIDC_CSF_RGB;
+	case DRM_FORMAT_XBGR2101010:
+		xhdmi->xvidc_colordepth = XVIDC_BPC_10;
+		return XVIDC_CSF_RGB;
+
+	case DRM_FORMAT_VUY888:
+	case DRM_FORMAT_XVUY8888:
+	case DRM_FORMAT_Y8:
+	case DRM_FORMAT_YUV444:
+		xhdmi->xvidc_colordepth = XVIDC_BPC_8;
+		return XVIDC_CSF_YCRCB_444;
+	case DRM_FORMAT_XVUY2101010:
+	case DRM_FORMAT_Y10:
+	case DRM_FORMAT_X403:
+		xhdmi->xvidc_colordepth = XVIDC_BPC_10;
+		return XVIDC_CSF_YCRCB_444;
+
+	case DRM_FORMAT_YUYV: //packed, 8b
+	case DRM_FORMAT_UYVY: //packed, 8b
+	case DRM_FORMAT_NV16: //semi-planar, 8b
+		xhdmi->xvidc_colordepth = XVIDC_BPC_8;
+		return XVIDC_CSF_YCRCB_422;
+	case DRM_FORMAT_XV20: //semi-planar, 10b
+		xhdmi->xvidc_colordepth = XVIDC_BPC_10;
+		return XVIDC_CSF_YCRCB_422;
+
+	case DRM_FORMAT_NV12: //semi-planar, 8b
+		xhdmi->xvidc_colordepth = XVIDC_BPC_8;
+		return XVIDC_CSF_YCRCB_420;
+	case DRM_FORMAT_XV15: //semi-planar, 10b
+		xhdmi->xvidc_colordepth = XVIDC_BPC_10;
+		return XVIDC_CSF_YCRCB_420;
+
+	default:
+		printk("Warning: Unknown drm_fourcc format code: %d\n", drm_fourcc);
+		xhdmi->xvidc_colordepth = XVIDC_BPC_UNKNOWN;
+		return XVIDC_CSF_RGB;
+	}
+}
+
+/*
+ * Refer table 14 of CTA-861-G. Doesn't comply completely due to gap between
+ * v4l2 and drm. Also extended colorimetry of XHDMIC_AVI_InfoFrame is not upto
+ * date with CTA-861-G spec.  So override the ones with
+ * HDMI_EXTENDED_COLORIMETRY_xx without actually modifying the structures.
+ *
+ * Implementation partially referred from xxx_set_fmt API from driver
+ * adv7511-v4l2.c
+ */
+static void xlnx_drm_hdmi_set_colorimetry(struct xlnx_drm_hdmi *xhdmi)
+{
+	XV_HdmiTxSs *HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+	XHdmiC_AVI_InfoFrame *AviInfoFramePtr =
+				XV_HdmiTxSs_GetAviInfoframe(HdmiTxSsPtr);
+	/*
+	 * c = Colorimetry
+	 * ec = Extended Colorimetry
+	 * y = RGB or YCbCr
+	 * q = RGB Quantization Range
+	 * yq = YCC Quantization Range
+	 */
+	u8 c = HDMI_COLORIMETRY_NONE;
+	u8 ec = HDMI_EXTENDED_COLORIMETRY_XV_YCC_601;
+	u8 y = HDMI_COLORSPACE_RGB;
+	u8 q = HDMI_QUANTIZATION_RANGE_DEFAULT;
+	u8 yq = HDMI_YCC_QUANTIZATION_RANGE_LIMITED;
+
+	switch (xhdmi->xvidc_colorfmt) {
+	case XVIDC_CSF_YCRCB_444:
+		y = HDMI_COLORSPACE_YUV444;
+		break;
+	case XVIDC_CSF_YCRCB_420:
+		y = HDMI_COLORSPACE_YUV420;
+		break;
+	case XVIDC_CSF_YCRCB_422:
+		y = HDMI_COLORSPACE_YUV422;
+		break;
+	default:
+		break;
+	};
+
+	switch (xhdmi->colorspace_val) {
+	case V4L2_COLORSPACE_OPRGB:
+		c = HDMI_COLORIMETRY_EXTENDED;
+		ec = y ? HDMI_EXTENDED_COLORIMETRY_OPYCC_601 :
+			 HDMI_EXTENDED_COLORIMETRY_OPRGB;
+		break;
+	case V4L2_COLORSPACE_SMPTE170M:
+		c = y ? HDMI_COLORIMETRY_ITU_601 : HDMI_COLORIMETRY_NONE;
+		if (y && xhdmi->ycbcr_enc_val == V4L2_YCBCR_ENC_XV601) {
+			c = HDMI_COLORIMETRY_EXTENDED;
+			ec = HDMI_EXTENDED_COLORIMETRY_XV_YCC_601;
+		}
+		break;
+	case V4L2_COLORSPACE_REC709:
+		c = y ? HDMI_COLORIMETRY_ITU_709 : HDMI_COLORIMETRY_NONE;
+		if (y && xhdmi->ycbcr_enc_val == V4L2_YCBCR_ENC_XV709) {
+			c = HDMI_COLORIMETRY_EXTENDED;
+			ec = HDMI_EXTENDED_COLORIMETRY_XV_YCC_709;
+		}
+		break;
+	case V4L2_COLORSPACE_SRGB:
+		c = y ? HDMI_COLORIMETRY_EXTENDED : HDMI_COLORIMETRY_NONE;
+		ec = y ? HDMI_EXTENDED_COLORIMETRY_S_YCC_601 :
+			 HDMI_EXTENDED_COLORIMETRY_XV_YCC_601;
+		break;
+	case V4L2_COLORSPACE_BT2020:
+		c = HDMI_COLORIMETRY_EXTENDED;
+		if (y && xhdmi->ycbcr_enc_val == V4L2_YCBCR_ENC_BT2020_CONST_LUM)
+			ec = 5; /* Not yet available in hdmi.h */
+		else
+			ec = 6; /* Not yet available in hdmi.h */
+		break;
+	default:
+		break;
+	}
+
+	/*
+	 * CEA-861-F says that for RGB formats the YCC range must match the
+	 * RGB range, although sources should ignore the YCC range.
+	 *
+	 * The RGB quantization range shouldn't be non-zero if the EDID doesn't
+	 * have the Q bit set in the Video Capabilities Data Block, however this
+	 * isn't checked at the moment. The assumption is that the application
+	 * knows the EDID and can detect this.
+	 *
+	 * The same is true for the YCC quantization range: non-standard YCC
+	 * quantization ranges should only be sent if the EDID has the YQ bit
+	 * set in the Video Capabilities Data Block.
+	 */
+	switch (xhdmi->quantization_val) {
+	case V4L2_QUANTIZATION_FULL_RANGE:
+		q = y ? HDMI_QUANTIZATION_RANGE_DEFAULT :
+			HDMI_QUANTIZATION_RANGE_FULL;
+		yq = q ? q - 1 : HDMI_YCC_QUANTIZATION_RANGE_FULL;
+		break;
+	case V4L2_QUANTIZATION_LIM_RANGE:
+		q = y ? HDMI_QUANTIZATION_RANGE_DEFAULT :
+			HDMI_QUANTIZATION_RANGE_LIMITED;
+		yq = q ? q - 1 : HDMI_YCC_QUANTIZATION_RANGE_LIMITED;
+		break;
+	default:
+		break;
+	}
+
+	AviInfoFramePtr->Colorimetry = c;
+	AviInfoFramePtr->ExtendedColorimetry= ec;
+	AviInfoFramePtr->QuantizationRange = q;
+	AviInfoFramePtr->YccQuantizationRange = yq;
+}
+
+/**
+ * xlnx_drm_hdmi_encoder_atomic_mode_set -  drive the HDMI timing parameters
+ *
+ * @encoder: pointer to Xilinx DRM encoder
+ * @crtc_state: DRM crtc state
+ * @connector_state: DRM connector state
+ *
+ * This function derives the HDMI IP timing parameters from the timing
+ * values given to timing module.
+ */
+static void xlnx_drm_hdmi_encoder_atomic_mode_set(struct drm_encoder *encoder,
+				  struct drm_crtc_state *crtc_state,
+				  struct drm_connector_state *connector_state)
+{
+	struct xlnx_drm_hdmi *xhdmi = encoder_to_hdmi(encoder);
+	struct drm_display_mode *mode = &crtc_state->mode;
+	struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+
+	XVidC_VideoTiming vt;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	XVidC_VideoStream *HdmiTxSsVidStreamPtr;
+	XHdmiC_AVI_InfoFrame *AviInfoFramePtr;
+	XHdmiC_VSIF *VSIFPtr;
+	u32 TmdsClock = 0;
+	u32 PrevPhyTxRefClock = 0;
+	u32 Result;
+	u32 drm_fourcc;
+	int ret;
+	int i, frame_rate;
+	XVidC_VideoMode vic_id = 0;
+	XHdmiC_VicTable const *entry;
+
+	dev_dbg(xhdmi->dev,"%s\n", __func__);
+	HdmiTxSsPtr = &xhdmi->xv_hdmitxss;
+
+	VphyPtr = xhdmi->xvphy;
+	XGtPhyPtr = xhdmi->xgtphy;
+
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	xvphy_mutex_lock(xhdmi->phy[0]);
+	drm_mode_debug_printmodeline(mode);
+
+	drm_fourcc = encoder->crtc->primary->state->fb->format->format;
+	xhdmi->xvidc_colorfmt = hdmitx_find_media_bus(xhdmi, drm_fourcc);
+	dev_dbg(xhdmi->dev,"xvidc_colorfmt = %d\n", xhdmi->xvidc_colorfmt);
+	dev_dbg(xhdmi->dev,"xvidc_colordepth = %d\n", xhdmi->xvidc_colordepth);
+
+	dev_dbg(xhdmi->dev,"mode->clock = %d\n", mode->clock * 1000);
+	dev_dbg(xhdmi->dev,"mode->crtc_clock = %d\n", mode->crtc_clock * 1000);
+	dev_dbg(xhdmi->dev,"mode->pvsync = %d\n",
+		!!(mode->flags & DRM_MODE_FLAG_PVSYNC));
+	dev_dbg(xhdmi->dev,"mode->phsync = %d\n",
+		!!(mode->flags & DRM_MODE_FLAG_PHSYNC));
+	dev_dbg(xhdmi->dev,"mode->hsync_end = %d\n", mode->hsync_end);
+	dev_dbg(xhdmi->dev,"mode->hsync_start = %d\n", mode->hsync_start);
+	dev_dbg(xhdmi->dev,"mode->vsync_end = %d\n", mode->vsync_end);
+	dev_dbg(xhdmi->dev,"mode->vsync_start = %d\n", mode->vsync_start);
+	dev_dbg(xhdmi->dev,"mode->hdisplay = %d\n", mode->hdisplay);
+	dev_dbg(xhdmi->dev,"mode->vdisplay = %d\n", mode->vdisplay);
+	dev_dbg(xhdmi->dev,"mode->htotal = %d\n", mode->htotal);
+	dev_dbg(xhdmi->dev,"mode->vtotal = %d\n", mode->vtotal);
+	dev_dbg(xhdmi->dev,"vrefresh = %d\n", drm_mode_vrefresh(mode));
+	dev_dbg(xhdmi->dev,"mode->flags = %d interlace = %d\n", mode->flags,
+			!!(mode->flags & DRM_MODE_FLAG_INTERLACE));
+
+	/* Set bridge input and output parameters */
+	if (xhdmi->bridge) {
+		xlnx_bridge_set_input(xhdmi->bridge, adjusted_mode->hdisplay,
+				      adjusted_mode->vdisplay,
+				      xhdmi->in_fmt_prop_val);
+		xlnx_bridge_set_output(xhdmi->bridge, xhdmi->width_out_prop_val,
+				       xhdmi->height_out_prop_val,
+				       xhdmi->out_fmt_prop_val);
+		xlnx_bridge_enable(xhdmi->bridge);
+
+		frame_rate = drm_mode_vrefresh(adjusted_mode);
+
+		for (i = 0; i < VICTABLE_SIZE; i++) {
+			entry = &VicTable[i];
+			if (entry->Width == xhdmi->width_out_prop_val &&
+			    entry->Height == xhdmi->height_out_prop_val &&
+			    entry->AspectRatio == xhdmi->aspect_ratio_prop_val &&
+			    entry->FrameRate == frame_rate) {
+				vic_id = entry->Vic;
+				break;
+			}
+
+		}
+
+		if (vic_id){
+			mode = drm_display_mode_from_cea_vic(encoder->dev, vic_id);
+		} else {
+			dev_err(xhdmi->dev, "Unsupported Vic Id %d\n", vic_id);
+			return;
+		}
+	}
+
+	/* see slide 20 of http://events.linuxfoundation.org/sites/events/files/slides/brezillon-drm-kms.pdf */
+	vt.HActive = mode->hdisplay;
+	vt.HFrontPorch = mode->hsync_start - mode->hdisplay;
+	vt.HSyncWidth = mode->hsync_end - mode->hsync_start;
+	vt.HBackPorch = mode->htotal - mode->hsync_end;
+	vt.HTotal = mode->htotal;
+	vt.HSyncPolarity = !!(mode->flags & DRM_MODE_FLAG_PHSYNC);
+
+	/* Enable this code for debugging of NTSC and PAL resolution */
+	if((((mode->hdisplay == 720) && (mode->vdisplay == 240) && (drm_mode_vrefresh(mode) == 60)) ||
+			((mode->hdisplay == 720) && (mode->vdisplay == 288) && (drm_mode_vrefresh(mode) == 50)))
+			&& (mode->flags & DRM_MODE_FLAG_INTERLACE) && (mode->flags & DRM_MODE_FLAG_DBLCLK))
+	{
+		dev_dbg(xhdmi->dev,"NTSC/PAL\n");
+		vt.HActive *= 2;
+		vt.HFrontPorch *= 2;
+		vt.HSyncWidth *= 2;
+		vt.HBackPorch *= 2;
+		vt.HTotal *= 2;
+	}
+
+	vt.VActive = mode->vdisplay;
+	/* Progressive timing data is stored in field 0 */
+	vt.F0PVFrontPorch = mode->vsync_start - mode->vdisplay;
+	vt.F0PVSyncWidth = mode->vsync_end - mode->vsync_start;
+	vt.F0PVBackPorch = mode->vtotal - mode->vsync_end;
+	vt.F0PVTotal = mode->vtotal;
+
+	if(mode->flags & DRM_MODE_FLAG_INTERLACE) {
+		dev_dbg(xhdmi->dev,"Programming fields for interlace");
+
+		vt.VActive = mode->vdisplay;
+
+		vt.F0PVFrontPorch = (mode->vsync_start - (mode->vdisplay * 2)) / 2;
+		vt.F0PVSyncWidth = (mode->vsync_end - mode->vsync_start) / 2;
+		vt.F0PVBackPorch = (mode->vtotal - mode->vsync_end) / 2;
+		vt.F0PVTotal = mode->vdisplay + vt.F0PVFrontPorch + vt.F0PVSyncWidth
+				+ vt.F0PVBackPorch;
+
+		if((mode->vtotal - mode->vsync_end) % 2)
+			vt.F1VFrontPorch = 1 + (mode->vsync_start - (mode->vdisplay * 2)) / 2;
+		else
+			vt.F1VFrontPorch = (mode->vsync_start - (mode->vdisplay * 2)) / 2;
+		vt.F1VSyncWidth = (mode->vsync_end - mode->vsync_start) / 2;
+		vt.F1VBackPorch = (mode->vtotal - mode->vsync_end) / 2;
+		vt.F1VTotal = mode->vdisplay + vt.F1VFrontPorch + vt.F1VSyncWidth
+				+ vt.F1VBackPorch;
+	}
+
+	vt.VSyncPolarity = !!(mode->flags & DRM_MODE_FLAG_PVSYNC);
+
+	HdmiTxSsVidStreamPtr = XV_HdmiTxSs_GetVideoStream(HdmiTxSsPtr);
+	AviInfoFramePtr = XV_HdmiTxSs_GetAviInfoframe(HdmiTxSsPtr);
+	VSIFPtr = XV_HdmiTxSs_GetVSIF(HdmiTxSsPtr);
+
+	// Reset Avi InfoFrame
+	(void)memset((void *)AviInfoFramePtr, 0, sizeof(XHdmiC_AVI_InfoFrame));
+	// Reset Vendor Specific InfoFrame
+	(void)memset((void *)VSIFPtr, 0, sizeof(XHdmiC_VSIF));
+
+	if (xhdmi->isvphy) {
+		/* Get current Tx Ref clock from PHY */
+		PrevPhyTxRefClock = VphyPtr->HdmiTxRefClkHz;
+
+		/* Disable TX TDMS clock */
+		XVphy_Clkout1OBufTdsEnable(VphyPtr, XVPHY_DIR_TX, (FALSE));
+	} else {
+		/* Get current Tx Ref clock from PHY */
+		PrevPhyTxRefClock = XGtPhyPtr->HdmiTxRefClkHz;
+
+		/* Disable TX TDMS clock */
+		XHdmiphy1_Clkout1OBufTdsEnable(XGtPhyPtr, XHDMIPHY1_DIR_TX, (FALSE));
+	}
+
+	/* The isExtensive is made true to get the correct video timing by matching
+	 * all the parameters */
+	HdmiTxSsVidStreamPtr->VmId = XVidC_GetVideoModeIdExtensive(&vt,
+			drm_mode_vrefresh(mode), (u8)!!(mode->flags & DRM_MODE_FLAG_INTERLACE), (u8)TRUE);
+
+	dev_dbg(xhdmi->dev,"VmId = %d Interlaced = %d\n", HdmiTxSsVidStreamPtr->VmId, !!(mode->flags & DRM_MODE_FLAG_INTERLACE));
+	if (HdmiTxSsVidStreamPtr->VmId == XVIDC_VM_NOT_SUPPORTED) { //no match found in timing table
+		dev_dbg(xhdmi->dev,"Tx Video Mode not supported. Using DRM Timing\n");
+		HdmiTxSsVidStreamPtr->VmId = XVIDC_VM_CUSTOM;
+		HdmiTxSsVidStreamPtr->FrameRate = (XVidC_FrameRate)drm_mode_vrefresh(mode);
+		HdmiTxSsVidStreamPtr->Timing = vt; //overwrite with drm detected timing
+		HdmiTxSsVidStreamPtr->IsInterlaced = (!!(mode->flags & DRM_MODE_FLAG_INTERLACE));
+#ifdef DEBUG
+		XVidC_ReportTiming(&HdmiTxSsVidStreamPtr->Timing, (u8)!!(mode->flags & DRM_MODE_FLAG_INTERLACE));
+#endif
+	}
+
+	/* The value of xvidc_colordepth is set by calling hdmitx_find_media_bus()
+	 * API earlier in this function. Check whether the value is valid or not */
+	if (XVIDC_BPC_UNKNOWN == xhdmi->xvidc_colordepth)
+		xhdmi->xvidc_colordepth = (XVidC_ColorDepth)HdmiTxSsPtr->Config.MaxBitsPerPixel;
+
+	/* check if resolution is supported at requested bit depth */
+	switch (xhdmi->xvidc_colorfmt) {
+		case XVIDC_CSF_RGB:
+		case XVIDC_CSF_YCRCB_444:
+			if ((xhdmi->xvidc_colordepth > XVIDC_BPC_8) &&
+				(mode->hdisplay >= 3840) &&
+				(mode->vdisplay >= 2160) &&
+				(drm_mode_vrefresh(mode) >= XVIDC_FR_50HZ)) {
+					dev_dbg(xhdmi->dev,"INFO> UHD only supports 24-bits color depth\n");
+					xhdmi->xvidc_colordepth = XVIDC_BPC_8;
+			}
+			break;
+
+		default:
+			break;
+	}
+
+	TmdsClock = XV_HdmiTxSs_SetStream(HdmiTxSsPtr, HdmiTxSsVidStreamPtr->VmId, xhdmi->xvidc_colorfmt,
+			xhdmi->xvidc_colordepth, NULL);
+
+	//Update AVI InfoFrame
+	AviInfoFramePtr->Version = 2;
+	AviInfoFramePtr->ColorSpace = XV_HdmiC_XVidC_To_IfColorformat(xhdmi->xvidc_colorfmt);
+	AviInfoFramePtr->VIC = HdmiTxSsPtr->HdmiTxPtr->Stream.Vic;
+	xlnx_drm_hdmi_set_colorimetry(xhdmi);
+
+	if ( (HdmiTxSsVidStreamPtr->VmId == XVIDC_VM_1440x480_60_I) ||
+			(HdmiTxSsVidStreamPtr->VmId == XVIDC_VM_1440x576_50_I) ) {
+		AviInfoFramePtr->PixelRepetition = XHDMIC_PIXEL_REPETITION_FACTOR_2;
+	} else {
+		AviInfoFramePtr->PixelRepetition = XHDMIC_PIXEL_REPETITION_FACTOR_1;
+	}
+
+	// Set TX reference clock
+	if (xhdmi->isvphy)
+		VphyPtr->HdmiTxRefClkHz = TmdsClock;
+	else
+		XGtPhyPtr->HdmiTxRefClkHz = TmdsClock;
+
+	dev_dbg(xhdmi->dev,"(TmdsClock = %u, from XV_HdmiTxSs_SetStream())\n", TmdsClock);
+
+	if (xhdmi->isvphy) {
+		dev_dbg(xhdmi->dev,"XVphy_SetHdmiTxParam(PixPerClk = %d, ColorDepth = %d, ColorFormatId=%d)\n",
+		(int)HdmiTxSsVidStreamPtr->PixPerClk, (int)HdmiTxSsVidStreamPtr->ColorDepth,
+		(int)HdmiTxSsVidStreamPtr->ColorFormatId);
+
+		// Set GT TX parameters, this might change VphyPtr->HdmiTxRefClkHz
+		Result = XVphy_SetHdmiTxParam(VphyPtr, 0, XVPHY_CHANNEL_ID_CHA,
+					HdmiTxSsVidStreamPtr->PixPerClk,
+					HdmiTxSsVidStreamPtr->ColorDepth,
+					HdmiTxSsVidStreamPtr->ColorFormatId);
+	} else {
+		dev_dbg(xhdmi->dev,"XHdmiphy1_SetHdmiTxParam(PixPerClk = %d, ColorDepth = %d, ColorFormatId=%d)\n",
+		(int)HdmiTxSsVidStreamPtr->PixPerClk, (int)HdmiTxSsVidStreamPtr->ColorDepth,
+		(int)HdmiTxSsVidStreamPtr->ColorFormatId);
+
+		// Set GT TX parameters, this might change XGtPhyPtr->HdmiTxRefClkHz
+		Result = XHdmiphy1_SetHdmiTxParam(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CHA,
+					HdmiTxSsVidStreamPtr->PixPerClk,
+					HdmiTxSsVidStreamPtr->ColorDepth,
+					HdmiTxSsVidStreamPtr->ColorFormatId);
+	}
+	if (Result == (XST_FAILURE)) {
+		dev_dbg(xhdmi->dev,"Unable to set requested TX video resolution.\n\r");
+		xvphy_mutex_unlock(xhdmi->phy[0]);
+		hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+		return;
+	}
+
+	if (!xhdmi->bridge) {
+		if (xhdmi->isvphy)
+			adjusted_mode->clock = VphyPtr->HdmiTxRefClkHz / 1000;
+		else
+			adjusted_mode->clock = XGtPhyPtr->HdmiTxRefClkHz / 1000;
+	}
+	else {
+		adjusted_mode->clock = mode->clock;
+	}
+
+	dev_dbg(xhdmi->dev,"adjusted_mode->clock = %u Hz\n", adjusted_mode->clock);
+
+	/* request required tmds clock rate */
+	ret = clk_set_rate(xhdmi->tmds_clk,
+			   adjusted_mode->clock * (unsigned long)1000);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed to set tmds clock rate to %d: %d\n",
+					(adjusted_mode->clock * 1000), ret);
+	}
+	/* When switching between modes with same Phy RefClk phy tx_refxlk_rdy_en
+	 * signal must be toggled (asserted and de-asserted) to reset phy's
+	 * internal frequency detection state machine
+	 */
+	if (xhdmi->isvphy) {
+		dev_dbg(xhdmi->dev,"PrevPhyTxRefClock: %d, NewRefClock: %d\n", PrevPhyTxRefClock, VphyPtr->HdmiTxRefClkHz);
+		if (PrevPhyTxRefClock == VphyPtr->HdmiTxRefClkHz) {
+			/* Switching between resolutions with same frequency */
+			dev_dbg(xhdmi->dev,"***** Reset Phy Tx Frequency *******\n");
+			XVphy_ClkDetFreqReset(VphyPtr, 0, XVPHY_DIR_TX);
+		}
+	} else {
+		dev_dbg(xhdmi->dev,"PrevPhyTxRefClock: %d, NewRefClock: %d\n", PrevPhyTxRefClock, XGtPhyPtr->HdmiTxRefClkHz);
+		if (PrevPhyTxRefClock == XGtPhyPtr->HdmiTxRefClkHz) {
+			/* Switching between resolutions with same frequency */
+			dev_dbg(xhdmi->dev,"***** Reset Phy Tx Frequency *******\n");
+			XHdmiphy1_ClkDetFreqReset(XGtPhyPtr, 0, XHDMIPHY1_DIR_TX);
+		}
+	}
+
+	xhdmi->tx_audio_data->tmds_clk = clk_get_rate(xhdmi->tmds_clk);
+	/* if the mode is HDMI 2.0, use a multiplier value of 4 */
+	if (HdmiTxSsPtr->HdmiTxPtr->Stream.TMDSClockRatio) {
+		xhdmi->tx_audio_data->tmds_clk =
+			xhdmi->tx_audio_data->tmds_clk * 4;
+		xhdmi->tx_audio_data->tmds_clk_ratio = true;
+	} else {
+		xhdmi->tx_audio_data->tmds_clk_ratio = false;
+	}
+
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+
+	xhdmi->wait_for_streamup = 0;
+	wait_event_timeout(xhdmi->wait_event, xhdmi->wait_for_streamup, msecs_to_jiffies(10000));
+	if (!xhdmi->wait_for_streamup)
+		dev_dbg(xhdmi->dev, "wait_for_streamup timeout\n");
+	/* Keep SYS_RST asserted */
+	XV_HdmiTxSs_SYSRST(HdmiTxSsPtr, TRUE);
+}
+
+static const struct drm_encoder_funcs xlnx_drm_hdmi_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+static const struct drm_encoder_helper_funcs xlnx_drm_hdmi_encoder_helper_funcs = {
+	//.dpms				= xlnx_drm_hdmi_encoder_dpms,
+	.enable				= xlnx_drm_hdmi_encoder_enable,
+	.disable			= xlnx_drm_hdmi_encoder_disable,
+	.atomic_mode_set	= xlnx_drm_hdmi_encoder_atomic_mode_set,
+};
+
+/* this function is responsible for periodically calling XV_HdmiTxSs_HdcpPoll()
+	and XHdcp_Authenticate */
+static void hdcp_poll_work(struct work_struct *work)
+{
+	/* find our parent container structure */
+	struct xlnx_drm_hdmi *xhdmi = container_of(work, struct xlnx_drm_hdmi,
+		delayed_work_hdcp_poll.work);
+	XV_HdmiTxSs *HdmiTxSsPtr;
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	if (XV_HdmiTxSs_HdcpIsReady(HdmiTxSsPtr)) {
+		hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+		XV_HdmiTxSs_HdcpPoll(HdmiTxSsPtr);
+		xhdmi->hdcp_auth_counter++;
+		if(xhdmi->hdcp_auth_counter >= 10) { //every 10ms
+			xhdmi->hdcp_auth_counter = 0;
+			if (xhdmi->hdcp_authenticate) {
+				XHdcp_Authenticate(HdmiTxSsPtr);
+			}
+		}
+		hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+	}
+	/* reschedule this work again in 1 millisecond */
+	schedule_delayed_work(&xhdmi->delayed_work_hdcp_poll, msecs_to_jiffies(1));
+	return;
+}
+
+static int XHdcp_KeyManagerInit(uintptr_t BaseAddress, u8 *Hdcp14Key)
+{
+	u32 RegValue;
+	u8 Row;
+	u8 i;
+	u8 *KeyPtr;
+	u8 Status;
+
+	/* Assign key pointer */
+	KeyPtr = Hdcp14Key;
+
+	/* Reset */
+	Xil_Out32((BaseAddress + 0x0c), (1<<31));
+
+	// There are 41 rows
+	for (Row=0; Row<41; Row++)
+	{
+		/* Set write enable */
+		Xil_Out32((BaseAddress + 0x20), 1);
+
+		/* High data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		/* Write high data */
+		Xil_Out32((BaseAddress + 0x2c), RegValue);
+
+		/* Low data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		/* Write low data */
+		Xil_Out32((BaseAddress + 0x30), RegValue);
+
+		/* Table / Row Address */
+		Xil_Out32((BaseAddress + 0x28), Row);
+
+		// Write in progress
+		do
+		{
+			RegValue = Xil_In32(BaseAddress + 0x24);
+			RegValue &= 1;
+		} while (RegValue != 0);
+	}
+
+	// Verify
+
+	/* Re-Assign key pointer */
+	KeyPtr = Hdcp14Key;
+
+	/* Default Status */
+	Status = XST_SUCCESS;
+
+	/* Start at row 0 */
+	Row = 0;
+
+	do
+	{
+		/* Set read enable */
+		Xil_Out32((BaseAddress + 0x20), (1<<1));
+
+		/* Table / Row Address */
+		Xil_Out32((BaseAddress + 0x28), Row);
+
+		// Read in progress
+		do
+		{
+			RegValue = Xil_In32(BaseAddress + 0x24);
+			RegValue &= 1;
+		} while (RegValue != 0);
+
+		/* High data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		if (RegValue != Xil_In32(BaseAddress + 0x2c))
+			Status = XST_FAILURE;
+
+		/* Low data */
+		RegValue = 0;
+		for (i=0; i<4; i++)
+		{
+			RegValue <<= 8;
+			RegValue |= *KeyPtr;
+			KeyPtr++;
+		}
+
+		if (RegValue != Xil_In32(BaseAddress + 0x30))
+			Status = XST_FAILURE;
+
+		/* Increment row */
+		Row++;
+
+	} while ((Row<41) && (Status == XST_SUCCESS));
+
+	if (Status == XST_SUCCESS)
+	{
+		/* Set read lockout */
+		Xil_Out32((BaseAddress + 0x20), (1<<31));
+
+		/* Start AXI-Stream */
+		Xil_Out32((BaseAddress + 0x0c), (1));
+	}
+
+	return Status;
+}
+
+
+/* -----------------------------------------------------------------------------
+ * Platform Device Driver
+ */
+
+static int instance = 0;
+/* TX uses [1, 127] and RX uses [128, 254] */
+/* The HDCP22 timer uses an additional offset of +64 */
+#define TX_DEVICE_ID_BASE 1
+
+/* Local Global table for all sub-core instance(s) configuration settings */
+XVtc_Config XVtc_ConfigTable[XPAR_XVTC_NUM_INSTANCES];
+XV_HdmiTx_Config XV_HdmiTx_ConfigTable[XPAR_XV_HDMITX_NUM_INSTANCES];
+
+extern XHdcp22_Cipher_Config XHdcp22_Cipher_ConfigTable[];
+extern XHdcp22_Rng_Config XHdcp22_Rng_ConfigTable[];
+extern XHdcp1x_Config XHdcp1x_ConfigTable[];
+extern XTmrCtr_Config XTmrCtr_ConfigTable[];
+extern XHdcp22_Tx_Config XHdcp22_Tx_ConfigTable[];
+
+/* Compute the absolute address by adding subsystem base address
+   to sub-core offset */
+static int xhdmi_drm_subcore_AbsAddr(uintptr_t SubSys_BaseAddr,
+									 uintptr_t SubSys_HighAddr,
+									 uintptr_t SubCore_Offset,
+									 uintptr_t *SubCore_AbsAddr)
+{
+  int Status;
+  uintptr_t absAddr;
+
+  absAddr = SubSys_BaseAddr | SubCore_Offset;
+  if((absAddr>=SubSys_BaseAddr) && (absAddr<=SubSys_HighAddr)) {
+    *SubCore_AbsAddr = absAddr;
+    Status = XST_SUCCESS;
+  } else {
+    *SubCore_AbsAddr = 0;
+    Status = XST_FAILURE;
+  }
+
+  return(Status);
+}
+
+/* Each sub-core within the subsystem has defined offset read from
+   device-tree. */
+static int xhdmi_drm_compute_subcore_AbsAddr(XV_HdmiTxSs_Config *config)
+{
+	int ret;
+
+	/* Subcore: Tx */
+	ret = xhdmi_drm_subcore_AbsAddr(config->BaseAddress,
+									config->HighAddress,
+									config->HdmiTx.AbsAddr,
+									&(config->HdmiTx.AbsAddr));
+	if (ret != XST_SUCCESS) {
+	   return -EFAULT;
+	}
+	XV_HdmiTx_ConfigTable[instance].BaseAddress = config->HdmiTx.AbsAddr;
+
+	/* Subcore: Vtc */
+	ret = xhdmi_drm_subcore_AbsAddr(config->BaseAddress,
+									config->HighAddress,
+									config->Vtc.AbsAddr,
+									&(config->Vtc.AbsAddr));
+	if (ret != XST_SUCCESS) {
+	   return -EFAULT;
+	}
+	XVtc_ConfigTable[instance].BaseAddress = config->Vtc.AbsAddr;
+
+	/* Subcore: hdcp1x */
+	if (config->Hdcp14.IsPresent) {
+	  ret = xhdmi_drm_subcore_AbsAddr(config->BaseAddress,
+		  							  config->HighAddress,
+									  config->Hdcp14.AbsAddr,
+									  &(config->Hdcp14.AbsAddr));
+	  if (ret != XST_SUCCESS) {
+	     return -EFAULT;
+	  }
+	  XHdcp1x_ConfigTable[instance].BaseAddress = config->Hdcp14.AbsAddr;
+	}
+
+	/* Subcore: hdcp1x timer */
+	if (config->HdcpTimer.IsPresent) {
+	  ret = xhdmi_drm_subcore_AbsAddr(config->BaseAddress,
+	  								  config->HighAddress,
+	  								  config->HdcpTimer.AbsAddr,
+	  								  &(config->HdcpTimer.AbsAddr));
+	  if (ret != XST_SUCCESS) {
+	     return -EFAULT;
+	  }
+	  XTmrCtr_ConfigTable[instance * 2 + 0].BaseAddress = config->HdcpTimer.AbsAddr;
+	}
+
+	/* Subcore: hdcp22 */
+	if (config->Hdcp22.IsPresent) {
+	  ret = xhdmi_drm_subcore_AbsAddr(config->BaseAddress,
+	  								  config->HighAddress,
+	  								  config->Hdcp22.AbsAddr,
+	  								  &(config->Hdcp22.AbsAddr));
+
+	  if (ret != XST_SUCCESS) {
+	     return -EFAULT;
+	  }
+	  XHdcp22_Tx_ConfigTable[instance].BaseAddress = config->Hdcp22.AbsAddr;
+	}
+
+	return (ret);
+}
+
+/*
+*	tx driver sysfs entries
+*/
+static ssize_t vphy_log_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	if (xhdmi->isvphy) {
+		VphyPtr = xhdmi->xvphy;
+		count = XVphy_LogShow(VphyPtr, buf, PAGE_SIZE);
+	} else {
+		XGtPhyPtr = xhdmi->xgtphy;
+		count = XHdmiphy1_LogShow(XGtPhyPtr, buf, PAGE_SIZE);
+	}
+	return count;
+}
+
+static ssize_t vphy_info_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XVphy *VphyPtr;
+	XHdmiphy1 *XGtPhyPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	if (xhdmi->isvphy) {
+		VphyPtr = xhdmi->xvphy;
+		count = XVphy_HdmiDebugInfo(VphyPtr, 0, XVPHY_CHANNEL_ID_CHA, buf, PAGE_SIZE);
+		count += scnprintf(&buf[count], (PAGE_SIZE-count), "Tx Ref Clk: %0d Hz\n",
+				XVphy_ClkDetGetRefClkFreqHz(xhdmi->xvphy, XVPHY_DIR_TX));
+	} else {
+		XGtPhyPtr = xhdmi->xgtphy;
+		count = XHdmiphy1_HdmiDebugInfo(XGtPhyPtr, 0, XHDMIPHY1_CHANNEL_ID_CHA, buf, PAGE_SIZE);
+		count += scnprintf(&buf[count], (PAGE_SIZE-count), "Tx Ref Clk: %0d Hz\n",
+				XHdmiphy1_ClkDetGetRefClkFreqHz(xhdmi->xgtphy, XHDMIPHY1_DIR_TX));
+	}
+	return count;
+}
+
+static ssize_t hdmi_log_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	count = XV_HdmiTxSs_LogShow(HdmiTxSsPtr, buf, PAGE_SIZE);
+	return count;
+}
+
+static ssize_t hdmi_info_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	count = XVidC_ShowStreamInfo(&HdmiTxSsPtr->HdmiTxPtr->Stream.Video, buf, PAGE_SIZE);
+	count += XV_HdmiTxSs_ShowInfo(HdmiTxSsPtr, &buf[count], (PAGE_SIZE-count));
+	return count;
+}
+
+static ssize_t hdcp_log_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	count = XV_HdmiTxSs_HdcpInfo(HdmiTxSsPtr, buf, PAGE_SIZE);
+	return count;
+}
+
+static ssize_t hdcp_authenticate_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	long int i;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	if (kstrtol(buf, 10, &i)) {
+		dev_dbg(xhdmi->dev, "hdcp_authenticate_store() input invalid.\n");
+		return count;
+	}
+	i = !!i;
+	xhdmi->hdcp_authenticate = i;
+	if (i && XV_HdmiTxSs_HdcpIsReady(HdmiTxSsPtr)) {
+		XV_HdmiTxSs_HdcpSetProtocol(HdmiTxSsPtr, XV_HDMITXSS_HDCP_22);
+		XV_HdmiTxSs_HdcpAuthRequest(HdmiTxSsPtr);
+	}
+	return count;
+}
+
+static ssize_t hdcp_encrypt_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	long int i;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	if (kstrtol(buf, 10, &i)) {
+		dev_dbg(xhdmi->dev, "hdcp_encrypt_store() input invalid.\n");
+		return count;
+	}
+	i = !!i;
+	xhdmi->hdcp_encrypt = i;
+	return count;
+}
+
+static ssize_t hdcp_protect_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	long int i;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	if (kstrtol(buf, 10, &i)) {
+		dev_dbg(xhdmi->dev, "hdcp_protect_store() input invalid.\n");
+		return count;
+	}
+	i = !!i;
+	xhdmi->hdcp_protect = i;
+	hdcp_protect_content(xhdmi);
+	return count;
+}
+
+static ssize_t hdcp_debugen_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	long int i;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+	if (kstrtol(buf, 10, &i)) {
+		dev_dbg(xhdmi->dev, "hdcp_debugen_store() input invalid.\n");
+		return count;
+	}
+	i = !!i;
+	if (i) {
+		/* Enable detail logs for hdcp transactions*/
+		XV_HdmiTxSs_HdcpSetInfoDetail(HdmiTxSsPtr, TRUE);
+	} else {
+		/* Disable detail logs for hdcp transactions*/
+		XV_HdmiTxSs_HdcpSetInfoDetail(HdmiTxSsPtr, FALSE);
+	}
+	return count;
+}
+
+static ssize_t hdcp_authenticate_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_authenticate);
+	return count;
+}
+
+static ssize_t hdcp_encrypt_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_encrypt);
+	return count;
+}
+
+static ssize_t hdcp_protect_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_protect);
+	return count;
+}
+
+static ssize_t hdcp_authenticated_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_authenticated);
+	return count;
+}
+
+static ssize_t hdcp_encrypted_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%d", xhdmi->hdcp_encrypted);
+	return count;
+}
+
+
+/* This function decrypts the HDCP keys, uses aes256.c */
+/* Note that the bare-metal implementation deciphers in-place in the cipherbuffer, then after that copies to the plaintext buffer,
+ * thus trashing the source.
+ *
+ * In this implementation, a local buffer is created (aligned to 16Byte boundary), the cipher is first copied to the local buffer,
+ * where it is then decrypted in-place and then copied over to target Plain Buffer. This leaves the source buffer intact.
+ */
+static int Decrypt(const u8 *CipherBufferPtr/*src*/, u8 *PlainBufferPtr/*dst*/, u8 *Key, u16 Length)
+{
+	u16 i;
+	u8 *AesBufferPtr;
+	u8 *LocalBuf; //16Byte aligned
+	u16 AesLength;
+	aes256_context ctx;
+
+	AesLength = Length/16; // The aes always encrypts 16 bytes
+	if (Length % 16) {
+		AesLength++;
+	}
+
+	//Allocate local buffer that is 16Byte aligned
+	LocalBuf = kzalloc((size_t)(AesLength*16), GFP_KERNEL);
+	if (!LocalBuf) {
+		printk(KERN_ERR "%s - %s Unable to allocate memory!\n",
+		       __FILE__, __func__);
+		return XST_FAILURE;
+	}
+
+	// Copy cipher into local buffer
+	memcpy(LocalBuf, CipherBufferPtr, (AesLength*16));
+
+	// Assign local Pointer // @NOTE: Changed
+	AesBufferPtr = LocalBuf;
+
+	// Initialize AES256
+	aes256_init(&ctx, Key);
+
+	for (i=0; i<AesLength; i++)
+	{
+		// Decrypt
+		aes256_decrypt_ecb(&ctx, AesBufferPtr);
+
+		// Increment pointer
+		AesBufferPtr += 16;	// The aes always encrypts 16 bytes
+	}
+
+	// Done
+	aes256_done(&ctx);
+
+	//copy decrypted key into Plainbuffer
+	memcpy(PlainBufferPtr, LocalBuf, Length);
+
+	//free local buffer
+	kfree(LocalBuf);
+
+	return XST_SUCCESS;
+}
+
+#define SIGNATURE_OFFSET			0
+#define HDCP22_LC128_OFFSET			16
+#define HDCP22_CERTIFICATE_OFFSET	32
+#define HDCP14_KEY1_OFFSET			1024
+#define HDCP14_KEY2_OFFSET			1536
+
+/* buffer points to the encrypted data (from EEPROM), password points to a 32-character password */
+static int XHdcp_LoadKeys(const u8 *Buffer, u8 *Password, u8 *Hdcp22Lc128, u32 Hdcp22Lc128Size, u8 *Hdcp22RxPrivateKey, u32 Hdcp22RxPrivateKeySize,
+	u8 *Hdcp14KeyA, u32 Hdcp14KeyASize, u8 *Hdcp14KeyB, u32 Hdcp14KeyBSize)
+{
+	u8 i;
+	const u8 HdcpSignature[16] = { "xilinx_hdcp_keys" };
+	u8 Key[32] = {0};
+	u8 SignatureOk;
+	u8 HdcpSignatureBuffer[16];
+	int ret;
+
+	// Generate password hash
+	XHdcp22Cmn_Sha256Hash(Password, 32, Key);
+
+	/* decrypt the signature */
+	ret = Decrypt(&Buffer[SIGNATURE_OFFSET]/*source*/, HdcpSignatureBuffer/*destination*/, Key, sizeof(HdcpSignature));
+	if (ret != XST_SUCCESS)
+		return ret;
+
+	SignatureOk = 1;
+	for (i = 0; i < sizeof(HdcpSignature); i++) {
+		if (HdcpSignature[i] != HdcpSignatureBuffer[i])
+			SignatureOk = 0;
+	}
+
+	/* password and buffer are correct, as the generated key could correctly decrypt the signature */
+	if (SignatureOk == 1) {
+		/* decrypt the keys */
+		ret = Decrypt(&Buffer[HDCP22_LC128_OFFSET], Hdcp22Lc128, Key, Hdcp22Lc128Size);
+		if (ret != XST_SUCCESS)
+			return ret;
+		ret = Decrypt(&Buffer[HDCP22_CERTIFICATE_OFFSET], Hdcp22RxPrivateKey, Key, Hdcp22RxPrivateKeySize);
+		if (ret != XST_SUCCESS)
+			return ret;
+		ret = Decrypt(&Buffer[HDCP14_KEY1_OFFSET], Hdcp14KeyA, Key, Hdcp14KeyASize);
+		if (ret != XST_SUCCESS)
+			return ret;
+		ret = Decrypt(&Buffer[HDCP14_KEY2_OFFSET], Hdcp14KeyB, Key, Hdcp14KeyBSize);
+		if (ret != XST_SUCCESS)
+			return ret;
+
+		return XST_SUCCESS;
+	} else {
+		printk(KERN_INFO "HDCP key store signature mismatch; HDCP key data and/or password are invalid.\n");
+	}
+	return XST_FAILURE;
+}
+
+/* assume the HDCP C structures containing the keys are valid, and sets them in the bare-metal driver / IP */
+static int hdcp_keys_configure(struct xlnx_drm_hdmi *xhdmi)
+{
+	XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	if (xhdmi->config.Hdcp14.IsPresent && xhdmi->config.HdcpTimer.IsPresent && xhdmi->hdcp1x_keymngmt_iomem) {
+		u8 Status;
+		dev_dbg(xhdmi->dev,"HDCP1x components are all there.\n");
+		/* Set pointer to HDCP 1.4 key */
+		XV_HdmiTxSs_HdcpSetKey(HdmiTxSsPtr, XV_HDMITXSS_KEY_HDCP14, xhdmi->Hdcp14KeyA);
+		/* Key manager Init */
+		Status = XHdcp_KeyManagerInit((uintptr_t)xhdmi->hdcp1x_keymngmt_iomem, HdmiTxSsPtr->Hdcp14KeyPtr);
+		if (Status != XST_SUCCESS) {
+			dev_err(xhdmi->dev, "HDCP 1.4 TX Key Manager initialization error.\n");
+			return -EINVAL;
+		}
+		dev_info(xhdmi->dev, "HDCP 1.4 TX Key Manager initialized OK.\n");
+	}
+	if (xhdmi->config.Hdcp22.IsPresent) {
+		/* Set pointer to HDCP 2.2 LC128 */
+		XV_HdmiTxSs_HdcpSetKey(HdmiTxSsPtr, XV_HDMITXSS_KEY_HDCP22_LC128, xhdmi->Hdcp22Lc128);
+		XV_HdmiTxSs_HdcpSetKey(HdmiTxSsPtr, XV_HDMITXSS_KEY_HDCP22_SRM, (u8 *)&Hdcp22Srm[0]);
+	}
+	return 0;
+}
+
+/* the EEPROM contents (i.e. the encrypted HDCP keys) must be dumped as a binary blob;
+ * the user must first upload the password */
+static ssize_t hdcp_key_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+	XV_HdmiTxSs *HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	/* check for valid size of HDCP encrypted key binary blob, @TODO adapt */
+	if (count < 1872) {
+		dev_dbg(xhdmi->dev, "hdcp_key_store(count = %d, expected >=1872)\n", (int)count);
+		return -EINVAL;
+	}
+	xhdmi->hdcp_password_accepted = 0;
+	/* decrypt the keys from the binary blob (buffer) into the C structures for keys */
+	if (XHdcp_LoadKeys((const u8 *)buf, xhdmi->hdcp_password,
+		xhdmi->Hdcp22Lc128, sizeof(xhdmi->Hdcp22Lc128),
+		xhdmi->Hdcp22PrivateKey, sizeof(xhdmi->Hdcp22PrivateKey),
+		xhdmi->Hdcp14KeyA, sizeof(xhdmi->Hdcp14KeyA),
+		xhdmi->Hdcp14KeyB, sizeof(xhdmi->Hdcp14KeyB)) == XST_SUCCESS) {
+
+		xhdmi->hdcp_password_accepted = 1;
+
+		/* configure the keys in the IP */
+		hdcp_keys_configure(xhdmi);
+
+		/* configure HDCP in HDMI */
+		u8 Status = XV_HdmiTxSs_CfgInitializeHdcp(HdmiTxSsPtr, &xhdmi->config, (uintptr_t)xhdmi->iomem);
+		if (Status != XST_SUCCESS) {
+			dev_err(xhdmi->dev, "XV_HdmiTxSs_CfgInitializeHdcp() failed with error %d\n", Status);
+			return -EINVAL;
+		}
+		XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_HDCP_AUTHENTICATED,
+			TxHdcpAuthenticatedCallback, (void *)xhdmi);
+		XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_HDCP_UNAUTHENTICATED,
+			TxHdcpUnauthenticatedCallback, (void *)xhdmi);
+
+		if (xhdmi->config.Hdcp14.IsPresent || xhdmi->config.Hdcp22.IsPresent) {
+			/* call into hdcp_poll_work, which will reschedule itself */
+			hdcp_poll_work(&xhdmi->delayed_work_hdcp_poll.work);
+		}
+	}
+	return count;
+}
+
+static ssize_t hdcp_password_show(struct device *sysfs_dev, struct device_attribute *attr,
+	char *buf)
+{
+	ssize_t count;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	count = scnprintf(buf, PAGE_SIZE, "%s", xhdmi->hdcp_password_accepted? "accepted": "rejected");
+	return count;
+}
+
+/* store the HDCP key password, after this the HDCP key can be written to sysfs */
+static ssize_t hdcp_password_store(struct device *sysfs_dev, struct device_attribute *attr,
+	const char *buf, size_t count)
+{
+	int i = 0;
+	struct xlnx_drm_hdmi *xhdmi = (struct xlnx_drm_hdmi *)dev_get_drvdata(sysfs_dev);
+
+	if (count > sizeof(xhdmi->hdcp_password)) return -EINVAL;
+	/* copy password characters up to newline or carriage return */
+	while ((i < count) && (i < sizeof(xhdmi->hdcp_password))) {
+		/* do not include newline or carriage return in password */
+		if ((buf[i] == '\n') || (buf[i] == '\r')) break;
+		xhdmi->hdcp_password[i] = buf[i];
+		i++;
+	}
+	/* zero remaining characters */
+	while (i < sizeof(xhdmi->hdcp_password)) {
+		xhdmi->hdcp_password[i] = 0;
+		i++;
+	}
+	return count;
+}
+
+static DEVICE_ATTR(vphy_log,  0444, vphy_log_show, NULL/*store*/);
+static DEVICE_ATTR(vphy_info, 0444, vphy_info_show, NULL/*store*/);
+static DEVICE_ATTR(hdmi_log,  0444, hdmi_log_show, NULL/*store*/);
+static DEVICE_ATTR(hdcp_log,  0444, hdcp_log_show, NULL/*store*/);
+static DEVICE_ATTR(hdmi_info, 0444, hdmi_info_show, NULL/*store*/);
+static DEVICE_ATTR(hdcp_debugen, 0220, NULL/*show*/, hdcp_debugen_store);
+static DEVICE_ATTR(hdcp_key, 0220, NULL/*show*/, hdcp_key_store);
+static DEVICE_ATTR(hdcp_password, 0660, hdcp_password_show, hdcp_password_store);
+
+/* readable and writable controls */
+DEVICE_ATTR(hdcp_authenticate, 0664, hdcp_authenticate_show, hdcp_authenticate_store);
+DEVICE_ATTR(hdcp_encrypt, 0664, hdcp_encrypt_show, hdcp_encrypt_store);
+DEVICE_ATTR(hdcp_protect, 0664, hdcp_protect_show, hdcp_protect_store);
+/* read-only status */
+DEVICE_ATTR(hdcp_authenticated, 0444, hdcp_authenticated_show, NULL/*store*/);
+DEVICE_ATTR(hdcp_encrypted, 0444, hdcp_encrypted_show, NULL/*store*/);
+
+static struct attribute *attrs[] = {
+	&dev_attr_vphy_log.attr,
+	&dev_attr_vphy_info.attr,
+	&dev_attr_hdmi_log.attr,
+	&dev_attr_hdcp_log.attr,
+	&dev_attr_hdmi_info.attr,
+	&dev_attr_hdcp_debugen.attr,
+	&dev_attr_hdcp_key.attr,
+	&dev_attr_hdcp_password.attr,
+	&dev_attr_hdcp_authenticate.attr,
+	&dev_attr_hdcp_encrypt.attr,
+	&dev_attr_hdcp_protect.attr,
+	&dev_attr_hdcp_authenticated.attr,
+	&dev_attr_hdcp_encrypted.attr,
+	NULL,
+};
+
+static struct attribute_group attr_group = {
+	.attrs = attrs,
+};
+
+static void xlnx_drm_hdmi_create_connector_property(
+		struct drm_connector *connector)
+{
+	struct drm_device *dev = connector->dev;
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+
+	xhdmi->colorspace =
+		drm_property_create_range(dev, 0, "colorspace", 0, 12);
+	xhdmi->ycbcr_enc =
+		drm_property_create_range(dev, 0, "ycbcr_enc", 0, 8);
+	xhdmi->xfer_func =
+		drm_property_create_range(dev, 0, "xfer_func", 0, 7);
+	xhdmi->quantization =
+		drm_property_create_range(dev, 0, "quantization", 0, 2);
+	xhdmi->height_out = drm_property_create_range(dev, 0, "height_out",
+						      XHDMI_VPSS_MIN_HEIGHT,
+						      XHDMI_VPSS_MAX_HEIGHT);
+	xhdmi->width_out = drm_property_create_range(dev, 0, "width_out",
+						     XHDMI_VPSS_MIN_WIDTH,
+						     XHDMI_VPSS_MAX_WIDTH);
+	/**
+	 *  in_fmt & out_fmt range is defined as per the VPSS scaler only
+	 *  supported media bus format values
+	 */
+	xhdmi->in_fmt = drm_property_create_range(dev, 0, "in_fmt",
+						  MEDIA_BUS_FMT_RGB888_1X24,
+						  MEDIA_BUS_FMT_VYYUYY8_1X24);
+	xhdmi->out_fmt = drm_property_create_range(dev, 0, "out_fmt",
+						   MEDIA_BUS_FMT_RGB888_1X24,
+						   MEDIA_BUS_FMT_VYYUYY8_1X24);
+	xhdmi->aspect_ratio = drm_property_create_range(dev, 0, "aspect_ratio",
+							XVIDC_AR_4_3, XVIDC_AR_256_135);
+}
+
+static void xlnx_drm_hdmi_attach_connector_property(
+		struct drm_connector *connector)
+{
+	struct xlnx_drm_hdmi *xhdmi = connector_to_hdmi(connector);
+	struct drm_mode_object *obj = &connector->base;
+
+	if (xhdmi->colorspace)
+		drm_object_attach_property(obj, xhdmi->colorspace, 0);
+	if (xhdmi->ycbcr_enc)
+		drm_object_attach_property(obj, xhdmi->ycbcr_enc, 0);
+	if (xhdmi->xfer_func)
+		drm_object_attach_property(obj, xhdmi->xfer_func, 0);
+	if (xhdmi->quantization)
+		drm_object_attach_property(obj, xhdmi->quantization, 0);
+	if (xhdmi->height_out)
+		drm_object_attach_property(obj, xhdmi->height_out, 0);
+	if (xhdmi->width_out)
+		drm_object_attach_property(obj, xhdmi->width_out, 0);
+	if (xhdmi->in_fmt)
+		drm_object_attach_property(obj, xhdmi->in_fmt, 0);
+	if (xhdmi->out_fmt)
+		drm_object_attach_property(obj, xhdmi->out_fmt, 0);
+	if (xhdmi->aspect_ratio)
+		drm_object_attach_property(obj, xhdmi->aspect_ratio, 0);
+}
+
+static int xlnx_drm_hdmi_create_connector(struct drm_encoder *encoder)
+{
+	struct xlnx_drm_hdmi *xhdmi = encoder_to_hdmi(encoder);
+	struct drm_connector *connector = &xhdmi->connector;
+	int ret;
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+	connector->interlace_allowed = true;
+
+	ret = drm_connector_init(encoder->dev, connector,
+				 &xlnx_drm_hdmi_connector_funcs,
+				 DRM_MODE_CONNECTOR_HDMIA);
+	if (ret) {
+		dev_err(xhdmi->dev, "Failed to initialize connector with drm\n");
+		return ret;
+	}
+
+	drm_connector_helper_add(connector, &xlnx_drm_hdmi_connector_helper_funcs);
+	ret = drm_connector_register(connector);
+	if (ret) {
+		dev_err(xhdmi->dev, "Failed to register the connector (ret=%d)\n", ret);
+		return ret;
+	}
+	ret = drm_connector_attach_encoder(connector, encoder);
+	if (ret) {
+		dev_err(xhdmi->dev,
+			"Failed to attach encoder to connector (ret=%d)\n", ret);
+		return ret;
+	}
+
+	drm_object_attach_property(&connector->base,
+			connector->dev->mode_config.gen_hdr_output_metadata_property,
+			0);
+
+	xlnx_drm_hdmi_create_connector_property(connector);
+	xlnx_drm_hdmi_attach_connector_property(connector);
+
+	return 0;
+}
+
+static int xlnx_drm_hdmi_bind(struct device *dev, struct device *master,
+			void *data)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	struct drm_encoder *encoder = &xhdmi->encoder;
+	struct drm_device *drm_dev = data;
+	int ret;
+
+	/* NOTE - "xlnx-drm" is the platform driver
+	 * "xlnx" is drm driver (Xilinx DRM KMS Driver)
+	 * In above case - drm_dev->driver->name = xlnx
+	 */
+
+	/*
+	 * TODO: The possible CRTCs are 1 now as per current implementation of
+	 * HDMI tx driver. DRM framework can support more than one CRTCs and
+	 * HDMI driver can be enhanced for that.
+	 */
+	encoder->possible_crtcs = 1;
+
+	/* initialize encoder */
+	drm_encoder_init(drm_dev, encoder, &xlnx_drm_hdmi_encoder_funcs,
+			 DRM_MODE_ENCODER_TMDS, NULL);
+	drm_encoder_helper_add(encoder, &xlnx_drm_hdmi_encoder_helper_funcs);
+
+	/* create connector */
+	ret = xlnx_drm_hdmi_create_connector(encoder);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed creating connector, ret = %d\n", ret);
+		drm_encoder_cleanup(encoder);
+	}
+	return ret;
+}
+
+static void xlnx_drm_hdmi_unbind(struct device *dev, struct device *master,
+				void *data)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+
+	if (xhdmi->bridge)
+		xlnx_bridge_disable(xhdmi->bridge);
+	xlnx_drm_hdmi_encoder_dpms(&xhdmi->encoder, DRM_MODE_DPMS_OFF);
+	drm_encoder_cleanup(&xhdmi->encoder);
+	drm_connector_cleanup(&xhdmi->connector);
+}
+
+static const struct component_ops xlnx_drm_hdmi_component_ops = {
+	.bind	= xlnx_drm_hdmi_bind,
+	.unbind	= xlnx_drm_hdmi_unbind
+};
+
+static void xlnx_drm_hdmi_initialize(struct xlnx_drm_hdmi *xhdmi)
+{
+	unsigned long flags;
+	XV_HdmiTxSs *HdmiTxSsPtr;
+	u32 Status;
+	int ret;
+
+	dev_dbg(xhdmi->dev, "%s\n", __func__);
+
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	HdmiTxSsPtr = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	Status = XV_HdmiTxSs_CfgInitialize(HdmiTxSsPtr, &xhdmi->config, (uintptr_t)xhdmi->iomem);
+	if (Status != XST_SUCCESS) {
+		dev_err(xhdmi->dev, "initialization failed with error %d\n", Status);
+	}
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiTxSs_IntrDisable(HdmiTxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+
+	/* TX SS callback setup */
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_CONNECT,
+		TxConnectCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_TOGGLE,
+		TxToggleCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_STREAM_UP,
+		TxStreamUpCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_STREAM_DOWN,
+		TxStreamDownCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_VS,
+		TxVsCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_BRDGUNLOCK,
+		TxBrdgUnlockedCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_BRDGOVERFLOW,
+		TxBrdgOverflowCallback, (void *)xhdmi);
+	XV_HdmiTxSs_SetCallback(HdmiTxSsPtr, XV_HDMITXSS_HANDLER_BRDGUNDERFLOW,
+		TxBrdgUnderflowCallback, (void *)xhdmi);
+
+	/* get a reference to the XVphy data structure */
+	if (xhdmi->isvphy)
+		xhdmi->xvphy = xvphy_get_xvphy(xhdmi->phy[0]);
+	else
+		xhdmi->xgtphy = xvphy_get_xvphy(xhdmi->phy[0]);
+
+	xvphy_mutex_lock(xhdmi->phy[0]);
+	/* the callback is not specific to a single lane, but we need to
+	 * provide one of the phys as reference */
+
+	if (xhdmi->isvphy) {
+		XVphy_SetHdmiCallback(xhdmi->xvphy, XVPHY_HDMI_HANDLER_TXINIT,
+			VphyHdmiTxInitCallback, (void *)xhdmi);
+		XVphy_SetHdmiCallback(xhdmi->xvphy, XVPHY_HDMI_HANDLER_TXREADY,
+			VphyHdmiTxReadyCallback, (void *)xhdmi);
+	} else {
+		XHdmiphy1_SetHdmiCallback(xhdmi->xgtphy, XHDMIPHY1_HDMI_HANDLER_TXINIT,
+			VphyHdmiTxInitCallback, (void *)xhdmi);
+		XHdmiphy1_SetHdmiCallback(xhdmi->xgtphy, XHDMIPHY1_HDMI_HANDLER_TXREADY,
+			VphyHdmiTxReadyCallback, (void *)xhdmi);
+	}
+	xvphy_mutex_unlock(xhdmi->phy[0]);
+
+	/* Request the interrupt */
+	ret = devm_request_threaded_irq(xhdmi->dev, xhdmi->irq, hdmitx_irq_handler, hdmitx_irq_thread,
+		IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmitxss", xhdmi/*dev_id*/);
+	if (ret) {
+		dev_err(xhdmi->dev, "unable to request IRQ %d\n", xhdmi->irq);
+	}
+
+	/* HDCP 1.4 Cipher interrupt */
+	if (xhdmi->hdcp1x_irq > 0) {
+		ret = devm_request_threaded_irq(xhdmi->dev, xhdmi->hdcp1x_irq, hdmitx_hdcp_irq_handler, hdmitx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmitxss-hdcp1x-cipher", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(xhdmi->dev, "unable to request IRQ %d\n", xhdmi->hdcp1x_irq);
+		}
+	}
+
+	/* HDCP 1.4 Timer interrupt */
+	if (xhdmi->hdcp1x_timer_irq > 0) {
+		ret = devm_request_threaded_irq(xhdmi->dev, xhdmi->hdcp1x_timer_irq, hdmitx_hdcp_irq_handler, hdmitx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmitxss-hdcp1x-timer", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(xhdmi->dev, "unable to request IRQ %d\n", xhdmi->hdcp1x_timer_irq);
+		}
+	}
+
+	/* HDCP 2.2 Timer interrupt */
+	if (xhdmi->hdcp22_timer_irq > 0) {
+		ret = devm_request_threaded_irq(xhdmi->dev, xhdmi->hdcp22_timer_irq, hdmitx_hdcp_irq_handler, hdmitx_hdcp_irq_thread,
+			IRQF_TRIGGER_HIGH /*| IRQF_SHARED*/, "xilinx-hdmitxss-hdcp22-timer", xhdmi/*dev_id*/);
+		if (ret) {
+			dev_err(xhdmi->dev, "unable to request IRQ %d\n", xhdmi->hdcp22_timer_irq);
+		}
+	}
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+
+	spin_lock_irqsave(&xhdmi->irq_lock, flags);
+	XV_HdmiTxSs_IntrEnable(HdmiTxSsPtr);
+	spin_unlock_irqrestore(&xhdmi->irq_lock, flags);
+}
+
+static int xlnx_drm_hdmi_parse_of(struct xlnx_drm_hdmi *xhdmi, XV_HdmiTxSs_Config *config)
+{
+	struct device *dev = xhdmi->dev;
+	struct device_node *node = dev->of_node;
+	int rc;
+	u32 val = 0;
+	bool isHdcp14_en, isHdcp22_en;
+
+	rc = of_property_read_u32(node, "xlnx,input-pixels-per-clock", &val);
+	if (rc < 0)
+		goto error_dt;
+	config->Ppc = (XVidC_PixelsPerClock)val;
+
+	rc = of_property_read_u32(node, "xlnx,max-bits-per-component", &val);
+	if (rc < 0)
+		goto error_dt;
+	config->MaxBitsPerPixel = val;
+
+
+	/* Tx Core */
+	config->HdmiTx.DeviceId = (u16)(TX_DEVICE_ID_BASE + instance);
+	config->HdmiTx.IsPresent = 1;
+	config->HdmiTx.AbsAddr = TXSS_TX_OFFSET;
+	XV_HdmiTx_ConfigTable[instance].DeviceId = TX_DEVICE_ID_BASE + instance;
+	XV_HdmiTx_ConfigTable[instance].BaseAddress = TXSS_TX_OFFSET;
+
+	rc = of_property_read_u32(node, "xlnx,vid-interface", &val);
+	if (rc < 0)
+		goto error_dt;
+
+	if (val != XHDMI_AXI_STREAM && val != XHDMI_NATIVE_VIDEO &&
+	    val != XHDMI_NATIVE_VIDEO_VDE) {
+		dev_err(xhdmi->dev, "Unsupported video interface: %d", val);
+		return -EINVAL;
+	}
+
+	/*VTC Core */
+	if (val == XHDMI_AXI_STREAM) {
+		config->Vtc.IsPresent = 1;
+		config->Vtc.DeviceId = TX_DEVICE_ID_BASE + instance;
+		config->Vtc.AbsAddr = TXSS_VTC_OFFSET;
+		XVtc_ConfigTable[instance].DeviceId = config->Vtc.DeviceId;
+		XVtc_ConfigTable[instance].BaseAddress = TXSS_VTC_OFFSET;
+	} else {
+		dev_dbg(xhdmi->dev, "Enabled native video interface\n");
+		config->Vtc.IsPresent = 0;
+	}
+
+	isHdcp14_en = of_property_read_bool(node, "xlnx,include-hdcp-1-4");
+	isHdcp22_en = of_property_read_bool(node, "xlnx,include-hdcp-2-2");
+	xhdmi->audio_enabled =
+		of_property_read_bool(node, "xlnx,audio-enabled");
+
+	if (isHdcp14_en) {
+		/* HDCP14 Core */
+		/* make subcomponent of TXSS present */
+		config->Hdcp14.IsPresent = 1;
+		config->Hdcp14.DeviceId = TX_DEVICE_ID_BASE + instance;
+		config->Hdcp14.AbsAddr = TXSS_HDCP14_OFFSET;
+		XHdcp1x_ConfigTable[instance].DeviceId = config->Hdcp14.DeviceId;
+		XHdcp1x_ConfigTable[instance].BaseAddress = TXSS_HDCP14_OFFSET;
+		XHdcp1x_ConfigTable[instance].IsRx = 0;
+		XHdcp1x_ConfigTable[instance].IsHDMI = 1;
+
+		/* HDCP14 Timer Core */
+		/* make subcomponent of TXSS present */
+		config->HdcpTimer.DeviceId = TX_DEVICE_ID_BASE + instance;
+		config->HdcpTimer.IsPresent = 1;
+		config->HdcpTimer.AbsAddr = TXSS_HDCP14_TIMER_OFFSET;
+
+		/* and configure it */
+		XTmrCtr_ConfigTable[instance * 2 + 0].DeviceId = config->HdcpTimer.DeviceId;
+		XTmrCtr_ConfigTable[instance * 2 + 0].BaseAddress = TXSS_HDCP14_TIMER_OFFSET;
+		/* @TODO increment timer index */
+	}
+
+	if (isHdcp22_en) {
+		/* HDCP22 SS */
+		config->Hdcp22.DeviceId = TX_DEVICE_ID_BASE + instance;
+		config->Hdcp22.IsPresent = 1;
+		config->Hdcp22.AbsAddr = TXSS_HDCP22_OFFSET;
+		XHdcp22_Tx_ConfigTable[instance].DeviceId = config->Hdcp22.DeviceId;
+		XHdcp22_Tx_ConfigTable[instance].BaseAddress = TXSS_HDCP22_OFFSET;
+		XHdcp22_Tx_ConfigTable[instance].Protocol = 0; //HDCP22_TX_HDMI
+		XHdcp22_Tx_ConfigTable[instance].Mode = 0; //XHDCP22_TX_TRANSMITTER
+		XHdcp22_Tx_ConfigTable[instance].TimerDeviceId = TX_DEVICE_ID_BASE + 64 + instance;
+		XHdcp22_Tx_ConfigTable[instance].CipherId = TX_DEVICE_ID_BASE + instance;
+		XHdcp22_Tx_ConfigTable[instance].RngId = TX_DEVICE_ID_BASE + instance;
+
+		/* HDCP22 Cipher Core */
+		XHdcp22_Cipher_ConfigTable[instance].DeviceId = TX_DEVICE_ID_BASE + instance;
+		XHdcp22_Cipher_ConfigTable[instance].BaseAddress = TX_HDCP22_CIPHER_OFFSET;
+		/* HDCP22-Timer Core */
+		XTmrCtr_ConfigTable[instance * 2 + 1].DeviceId = TX_DEVICE_ID_BASE + 64 + instance;
+		XTmrCtr_ConfigTable[instance * 2 + 1].BaseAddress = TX_HDCP22_TIMER_OFFSET;
+		/* HDCP22 RNG Core */
+		XHdcp22_Rng_ConfigTable[instance].DeviceId = TX_DEVICE_ID_BASE + instance;
+		XHdcp22_Rng_ConfigTable[instance].BaseAddress = TX_HDCP22_RNG_OFFSET;
+	}
+
+	if (isHdcp14_en || isHdcp22_en) {
+		rc = of_property_read_u32(node, "xlnx,hdcp-authenticate", &val);
+		if (rc == 0) {
+			xhdmi->hdcp_authenticate = val;
+		}
+		rc = of_property_read_u32(node, "xlnx,hdcp-encrypt", &val);
+		if (rc == 0) {
+			xhdmi->hdcp_encrypt = val;
+		}
+	} else {
+		xhdmi->hdcp_authenticate = 0;
+		xhdmi->hdcp_encrypt = 0;
+	}
+	// set default color format to RGB
+	xhdmi->xvidc_colorfmt = XVIDC_CSF_RGB;
+
+	if (xhdmi->audio_enabled) {
+		xhdmi->tx_audio_data->acr_base = hdmitx_parse_aud_dt(dev);
+		if (!xhdmi->tx_audio_data->acr_base) {
+			xhdmi->audio_init = false;
+			dev_err(dev, "tx audio: acr base parse failed\n");
+		}
+	} else {
+		dev_info(dev, "hdmi tx audio disabled in DT\n");
+	}
+	return 0;
+
+error_dt:
+	dev_err(xhdmi->dev, "Error parsing device tree");
+	return rc;
+}
+
+static int xlnx_drm_hdmi_probe(struct platform_device *pdev)
+{
+	struct xlnx_drm_hdmi *xhdmi;
+	int ret;
+	unsigned int index;
+	struct resource *res;
+	struct device_node *vpss_node;
+	unsigned long axi_clk_rate;
+
+	dev_info(&pdev->dev, "probe started\n");
+	/* allocate zeroed HDMI TX device structure */
+	xhdmi = devm_kzalloc(&pdev->dev, sizeof(*xhdmi), GFP_KERNEL);
+	if (!xhdmi)
+		return -ENOMEM;
+
+	xhdmi->tx_audio_data =
+		devm_kzalloc(&pdev->dev, sizeof(struct xlnx_hdmitx_audio_data),
+			     GFP_KERNEL);
+	if (!xhdmi->tx_audio_data)
+		return -ENOMEM;
+
+	/* store pointer of the real device inside platform device */
+	xhdmi->dev = &pdev->dev;
+
+	/* get ownership of the HDMI TXSS MMIO register space resource */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "unable to get register space resource!\n");
+		return -EINVAL;
+	}
+	/* map the MMIO region */
+	xhdmi->iomem = devm_ioremap_resource(xhdmi->dev, res);
+	if (IS_ERR(xhdmi->iomem)) {
+		dev_err(xhdmi->dev, "failed to remap io region\n");
+		return PTR_ERR(xhdmi->iomem);
+	}
+	/* mutex that protects against concurrent access */
+	mutex_init(&xhdmi->hdmi_mutex);
+	spin_lock_init(&xhdmi->irq_lock);
+
+	init_waitqueue_head(&xhdmi->wait_event);
+
+	dev_dbg(xhdmi->dev,"DT parse start\n");
+	/* parse open firmware device tree data */
+	ret = xlnx_drm_hdmi_parse_of(xhdmi, &xhdmi->config);
+	if (ret < 0)
+		return ret;
+
+	/* VPSS Bridge support */
+	vpss_node = of_parse_phandle(xhdmi->dev->of_node, "xlnx,vpss", 0);
+	if (vpss_node) {
+		xhdmi->bridge = of_xlnx_bridge_get(vpss_node);
+		if (!xhdmi->bridge) {
+			dev_info(xhdmi->dev, "Didn't get bridge instance\n");
+			return -EPROBE_DEFER;
+		}
+	}
+
+	dev_dbg(xhdmi->dev,"DT parse done\n");
+
+	/* acquire vphy lanes */
+	for (index = 0; index < 3; index++)
+	{
+		static const struct of_device_id xlnx_hdmi_phy_id_table[] = {
+			{ .compatible = "xlnx,hdmi-gt-controller-1.0", },
+			{ .compatible = "xlnx,vid-phy-controller-2.2", },
+			{ /* end of table */ },
+		};
+		const struct of_device_id *match;
+
+		char phy_name[16];
+		snprintf(phy_name, sizeof(phy_name), "hdmi-phy%d", index);
+		xhdmi->phy[index] = devm_phy_get(xhdmi->dev, phy_name);
+		if (IS_ERR(xhdmi->phy[index])) {
+			ret = PTR_ERR(xhdmi->phy[index]);
+			xhdmi->phy[index] = NULL;
+			if (ret == -EPROBE_DEFER) {
+				dev_info(xhdmi->dev, "xvphy/xgtphy not ready -EPROBE_DEFER\n");
+				return ret;
+			}
+			if (ret != -EPROBE_DEFER)
+				dev_err(xhdmi->dev, "failed to get phy lane %s index %d, error %d\n",
+					phy_name, index, ret);
+			goto error_phy;
+		}
+
+		match = of_match_node(xlnx_hdmi_phy_id_table, xhdmi->phy[index]->dev.parent->of_node);
+		if (!match) {
+			dev_err(xhdmi->dev, "of_match_node failed for phy!\n");
+			goto error_phy;
+		}
+
+		if (strncmp(match->compatible, "xlnx,vid-phy-controller", 23) == 0)
+			xhdmi->isvphy = 1;
+		else
+			xhdmi->isvphy = 0;
+
+		ret = phy_init(xhdmi->phy[index]);
+		if (ret) {
+			dev_err(xhdmi->dev,
+				"failed to init phy lane %d\n", index);
+			goto error_phy;
+		}
+	}
+
+	xhdmi->config.DeviceId = instance;
+	xhdmi->config.BaseAddress = (uintptr_t)xhdmi->iomem;
+	xhdmi->config.HighAddress = (uintptr_t)xhdmi->iomem + resource_size(res) - 1;
+
+	/* Compute sub-core AbsAddres */
+	ret = xhdmi_drm_compute_subcore_AbsAddr(&xhdmi->config);
+	if (ret == -EFAULT) {
+	   dev_err(xhdmi->dev, "hdmi-tx sub-core address out-of range\n");
+	   return ret;
+	}
+
+	/* 4 clock sources to be acquired and enabled */
+	/* acquire video streaming bus clock */
+	xhdmi->clk = devm_clk_get(xhdmi->dev, "s_axis_video_aclk");
+	if (IS_ERR(xhdmi->clk)) {
+		ret = PTR_ERR(xhdmi->clk);
+		if (ret == -EPROBE_DEFER)
+			dev_info(xhdmi->dev, "video-clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(xhdmi->dev, "failed to get video clk\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xhdmi->clk);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed to prep and enable axis video clk!\n");
+		return ret;
+	}
+
+	/* acquire axi-lite register bus clock */
+	xhdmi->axi_lite_clk = devm_clk_get(xhdmi->dev, "s_axi_cpu_aclk");
+	if (IS_ERR(xhdmi->axi_lite_clk)) {
+		ret = PTR_ERR(xhdmi->axi_lite_clk);
+		if (ret == -EPROBE_DEFER)
+			dev_info(xhdmi->dev, "axi-lite-clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(xhdmi->dev, "failed to get axi-lite clk\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xhdmi->axi_lite_clk);
+	if (ret) {
+		dev_err(xhdmi->dev, "failed to prep and enable axilite clk!\n");
+		return ret;
+	}
+
+	axi_clk_rate = clk_get_rate(xhdmi->axi_lite_clk);
+	dev_dbg(xhdmi->dev,"axi_clk_rate = %lu Hz\n", axi_clk_rate);
+	xhdmi->config.AxiLiteClkFreq = axi_clk_rate;
+
+	/* we now know the AXI clock rate */
+	XHdcp1x_ConfigTable[instance].SysFrequency = axi_clk_rate;
+	XTmrCtr_ConfigTable[instance * 2 + 0].SysClockFreqHz = axi_clk_rate;
+	XTmrCtr_ConfigTable[instance * 2 + 1].SysClockFreqHz = axi_clk_rate;
+	XV_HdmiTx_ConfigTable[instance].AxiLiteClkFreq = axi_clk_rate;
+
+	/* acquire Tmds clock for output resolution */
+	xhdmi->tmds_clk = devm_clk_get(&pdev->dev, "txref-clk");
+	if (IS_ERR(xhdmi->tmds_clk)) {
+		ret = PTR_ERR(xhdmi->tmds_clk);
+		xhdmi->tmds_clk = NULL;
+		if (ret == -EPROBE_DEFER)
+			dev_info(xhdmi->dev, "tx-clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(xhdmi->dev, "failed to get tx-clk.\n");
+		return ret;
+	}
+	dev_dbg(xhdmi->dev, "got txref-clk (default rate = %lu)\n", clk_get_rate(xhdmi->tmds_clk));
+	ret = clk_prepare_enable(xhdmi->tmds_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable tx clk\n");
+		return ret;
+	}
+
+	xhdmi->tx_audio_data->tmds_clk = clk_get_rate(xhdmi->tmds_clk);
+	/* support to drive an external retimer IC on the TX path, depending on TX clock line rate */
+	xhdmi->retimer_clk = devm_clk_get(&pdev->dev, "retimer-clk");
+	if (IS_ERR(xhdmi->retimer_clk)) {
+		ret = PTR_ERR(xhdmi->retimer_clk);
+		xhdmi->retimer_clk = NULL;
+		if (ret == -EPROBE_DEFER)
+			dev_info(xhdmi->dev, "retimer-clk not ready -EPROBE_DEFER\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(xhdmi->dev, "Did not find a retimer-clk, not driving an external retimer device driver.\n");
+		return ret;
+	} else if (xhdmi->retimer_clk) {
+		dev_dbg(xhdmi->dev,"got retimer-clk\n");
+		ret = clk_prepare_enable(xhdmi->retimer_clk);
+		if (ret) {
+			dev_err(xhdmi->dev, "failed to enable retimer-clk\n");
+			return ret;
+		}
+		dev_dbg(xhdmi->dev,"prepared and enabled retimer-clk\n");
+	} else {
+		dev_dbg(xhdmi->dev,"no retimer clk specified, assuming no redriver/retimer is used.\n");
+	}
+
+	/* get ownership of the HDCP1x key management MMIO register space resource */
+	if (xhdmi->config.Hdcp14.IsPresent) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hdcp1x-keymngmt");
+
+		if (res) {
+			dev_dbg(xhdmi->dev,"Mapping HDCP1x key management block.\n");
+			xhdmi->hdcp1x_keymngmt_iomem = devm_ioremap_resource(xhdmi->dev, res);
+			dev_dbg(xhdmi->dev,"HDCP1x key management block @%p.\n", xhdmi->hdcp1x_keymngmt_iomem);
+			if (IS_ERR(xhdmi->hdcp1x_keymngmt_iomem)) {
+				dev_dbg(xhdmi->dev,"Could not ioremap hdcp1x-keymngmt.\n");
+				return PTR_ERR(xhdmi->hdcp1x_keymngmt_iomem);
+			}
+		}
+	}
+
+	/* get HDMI TXSS irq */
+	xhdmi->irq = platform_get_irq(pdev, 0);
+	if (xhdmi->irq <= 0) {
+		dev_err(xhdmi->dev, "platform_get_irq() failed\n");
+		return xhdmi->irq;
+	}
+
+	if (xhdmi->config.Hdcp14.IsPresent) {
+	  xhdmi->hdcp1x_irq = platform_get_irq_byname(pdev, "hdcp14_irq");
+	  dev_dbg(xhdmi->dev,"xhdmi->hdcp1x_irq = %d\n", xhdmi->hdcp1x_irq);
+	  xhdmi->hdcp1x_timer_irq = platform_get_irq_byname(pdev, "hdcp14_timer_irq");
+	  dev_dbg(xhdmi->dev,"xhdmi->hdcp1x_timer_irq = %d\n", xhdmi->hdcp1x_timer_irq);
+	}
+
+	if (xhdmi->config.Hdcp22.IsPresent) {
+	  xhdmi->hdcp22_irq = platform_get_irq_byname(pdev, "hdcp22_irq");
+	  dev_dbg(xhdmi->dev,"xhdmi->hdcp22_irq = %d\n", xhdmi->hdcp22_irq);
+	  xhdmi->hdcp22_timer_irq = platform_get_irq_byname(pdev, "hdcp22_timer_irq");
+	  dev_dbg(xhdmi->dev,"xhdmi->hdcp22_timer_irq = %d\n", xhdmi->hdcp22_timer_irq);
+	}
+
+	if (xhdmi->config.Hdcp14.IsPresent || xhdmi->config.Hdcp22.IsPresent) {
+		INIT_DELAYED_WORK(&xhdmi->delayed_work_hdcp_poll, hdcp_poll_work/*function*/);
+	}
+
+	/* create sysfs group */
+	ret = sysfs_create_group(&xhdmi->dev->kobj, &attr_group);
+	if (ret) {
+		dev_err(xhdmi->dev, "sysfs group creation (%d) failed \n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, xhdmi);
+
+	/* initialize hw */
+	xlnx_drm_hdmi_initialize(xhdmi);
+
+	if (xhdmi->audio_enabled && xhdmi->tx_audio_data->acr_base) {
+		if (hdmitx_register_aud_dev(xhdmi->dev, instance)) {
+			xhdmi->audio_init = false;
+			dev_err(xhdmi->dev, "hdmi tx audio init failed\n");
+		} else {
+			xhdmi->audio_init = true;
+			dev_info(xhdmi->dev, "hdmi tx audio initialized\n");
+		}
+	}
+
+	/* probe has succeeded for this instance, increment instance index */
+	instance++;
+
+	dev_info(xhdmi->dev, "probe successful\n");
+	return component_add(xhdmi->dev, &xlnx_drm_hdmi_component_ops);
+
+error_phy:
+	dev_info(xhdmi->dev, "probe failed:: error_phy:\n");
+	index = 0;
+	/* release the lanes that we did get, if we did not get all lanes */
+	if (xhdmi->phy[index]) {
+		printk(KERN_INFO "phy_exit() xhdmi->phy[%d] = %p\n", index, xhdmi->phy[index]);
+		phy_exit(xhdmi->phy[index]);
+		xhdmi->phy[index] = NULL;
+	}
+
+	return ret;
+}
+
+static int xlnx_drm_hdmi_remove(struct platform_device *pdev)
+{
+	struct xlnx_drm_hdmi *xhdmi = platform_get_drvdata(pdev);
+
+	if (xhdmi->audio_init)
+		hdmitx_unregister_aud_dev(&pdev->dev);
+
+	sysfs_remove_group(&pdev->dev.kobj, &attr_group);
+	component_del(&pdev->dev, &xlnx_drm_hdmi_component_ops);
+	return 0;
+}
+
+struct xlnx_hdmitx_audio_data *hdmitx_get_audio_data(struct device *dev)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+
+	if (!xhdmi)
+		return NULL;
+	else
+		return xhdmi->tx_audio_data;
+}
+
+void hdmitx_audio_startup(struct device *dev)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiTxSs *xv_hdmitxss = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	XV_HdmiTxSs_AudioMute(xv_hdmitxss, 0);
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+}
+
+void hdmitx_audio_hw_params(struct device *dev,
+		struct hdmi_audio_infoframe *frame)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiTxSs *xv_hdmitxss = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	XV_HdmiTxSs_SetAudioChannels(xv_hdmitxss, frame->channels);
+	XV_HdmiTxSs_AudioMute(xv_hdmitxss, 0);
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+
+}
+
+void hdmitx_audio_shutdown(struct device *dev)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	XV_HdmiTxSs *xv_hdmitxss = (XV_HdmiTxSs *)&xhdmi->xv_hdmitxss;
+
+	hdmi_mutex_lock(&xhdmi->hdmi_mutex);
+	XV_HdmiTxSs_AudioMute(xv_hdmitxss, 1);
+	hdmi_mutex_unlock(&xhdmi->hdmi_mutex);
+}
+
+void hdmitx_audio_mute(struct device *dev, bool enable)
+{
+	if (enable)
+		hdmitx_audio_shutdown(dev);
+	else
+		hdmitx_audio_startup(dev);
+}
+
+int hdmitx_audio_geteld(struct device *dev, uint8_t *buf, size_t len)
+{
+	struct xlnx_drm_hdmi *xhdmi = dev_get_drvdata(dev);
+	size_t size;
+
+	if (xhdmi->have_edid) {
+		size = drm_eld_size(xhdmi->connector.eld);
+		if (size != 0) {
+			if (len < size)
+				size = len;
+			memcpy(buf, xhdmi->connector.eld, size);
+			return 0;
+		} else {
+			return -EINVAL;
+		}
+	}
+
+	return -EIO;
+}
+
+static const struct dev_pm_ops xhdmitx_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(hdmitx_pm_suspend, hdmitx_pm_resume)
+};
+
+static const struct of_device_id xlnx_drm_hdmi_of_match[] = {
+	{ .compatible = "xlnx,v-hdmi-tx-ss-3.1", },
+	{ /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xlnx_drm_hdmi_of_match);
+
+static struct platform_driver xlnx_drm_hdmi_driver = {
+	.probe			= xlnx_drm_hdmi_probe,
+	.remove			= xlnx_drm_hdmi_remove,
+	.driver			= {
+		.owner		= THIS_MODULE,
+		.name		= "xlnx-drm-hdmi",
+		.pm			= &xhdmitx_pm_ops,
+		.of_match_table	= xlnx_drm_hdmi_of_match,
+	},
+};
+
+
+module_platform_driver(xlnx_drm_hdmi_driver);
+
+MODULE_AUTHOR("rohit consul <rohitco@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx DRM KMS HDMI Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmirx_audio.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmirx_audio.c
@@ -0,0 +1,112 @@
+/*
+ * Xilinx ALSA SoC HDMI audio capture support
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/of_address.h>
+#include <sound/soc.h>
+#include <sound/hdmi-codec.h>
+
+#include "xlnx_hdmirx_audio.h"
+
+#define XV_AES_ENABLE 0x8
+
+
+/* xlnx_rx_pcm_startup - initialze audio during audio usecase
+ *
+ * This function is called by ALSA framework before audio
+ * capture begins.
+ *
+ * Return: 0 on success
+ */
+static int xlnx_rx_pcm_startup(struct snd_pcm_substream *substream,
+			struct snd_soc_dai *dai)
+{
+	u32 channels = hdmirx_audio_startup(dai->dev);
+
+	if (!channels)
+		return -EINVAL;
+
+	dev_info(dai->dev,
+		 "Detected audio with channel count = %d, starting capture\n",
+		 channels);
+	return 0;
+}
+
+/* xlnx_rx_pcm_shutdown - Deinitialze audio when audio usecase is stopped
+ *
+ * This function is called by ALSA framework before audio capture usecase
+ * ends.
+ */
+static void xlnx_rx_pcm_shutdown(struct snd_pcm_substream *substream,
+				struct snd_soc_dai *dai)
+{
+	hdmirx_audio_shutdown(dai->dev);
+}
+
+static const struct snd_soc_dai_ops xlnx_rx_dai_ops = {
+	.startup = xlnx_rx_pcm_startup,
+	.shutdown = xlnx_rx_pcm_shutdown,
+};
+
+static struct snd_soc_dai_driver xlnx_rx_audio_dai = {
+	.name = "xlnx_hdmi_rx",
+	.capture = {
+		.stream_name = "Capture",
+		.channels_min = 2,
+		.channels_max = 8,
+		.rates = SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 |
+			 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 |
+			 SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_176400 |
+			 SNDRV_PCM_RATE_192000,
+		.formats = SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE,
+	},
+	.ops = &xlnx_rx_dai_ops,
+};
+
+static int xlnx_rx_codec_probe(struct snd_soc_component *component)
+{
+	return 0;
+}
+
+void xlnx_rx_codec_remove(struct snd_soc_component *component)
+{
+}
+
+static const struct snd_soc_component_driver xlnx_rx_codec_driver = {
+	.probe = xlnx_rx_codec_probe,
+	.remove = xlnx_rx_codec_remove,
+};
+
+/* hdmirx_register_aud_dev - register audio device
+ *
+ * This functions registers codec DAI device as part of
+ * ALSA SoC framework.
+ */
+int hdmirx_register_aud_dev(struct device *dev)
+{
+	return snd_soc_register_component(dev, &xlnx_rx_codec_driver,
+			&xlnx_rx_audio_dai, 1);
+}
+
+/* hdmirx_register_aud_dev - register audio device
+ *
+ * This functions unregisters codec DAI device
+ */
+void hdmirx_unregister_aud_dev(struct device *dev)
+{
+	snd_soc_unregister_component(dev);
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmirx_audio.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmirx_audio.h
@@ -0,0 +1,36 @@
+/*
+ * Xilinx ALSA SoC HDMI audio capture support
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __XILINX_HDMI_RX_AUD_H__
+#define __XILINX_HDMI_RX_AUD_H__
+
+#define XHDMI_AUDIO_DETECT_TIMEOUT 50
+
+struct xlnx_hdmirx_audio_data *hdmirx_get_audio_data(struct device *dev);
+int hdmirx_register_aud_dev(struct device *dev);
+void hdmirx_unregister_aud_dev(struct device *dev);
+u32 hdmirx_audio_startup(struct device *dev);
+void hdmirx_audio_shutdown(struct device *dev);
+
+struct xlnx_hdmirx_audio_data {
+	void __iomem *aes_base;
+	bool audio_detected;
+	wait_queue_head_t audio_update_q;
+	int format;
+	u8 num_channels;
+};
+#endif /* __XILINX_HDMI_RX_AUD_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmitx_audio.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmitx_audio.c
@@ -0,0 +1,510 @@
+/*
+ * Xilinx ALSA SoC HDMI audio playback support
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drm_crtc.h> /* This is only to get MAX_ELD_BYTES */
+#include <linux/hdmi.h>
+#include <linux/of_address.h>
+#include <sound/soc.h>
+#include <sound/pcm_drm_eld.h>
+
+#include "xlnx_hdmitx_audio.h"
+
+#define XV_ACR_ENABLE 0x4
+#define XV_ACR_N 0xc
+#define ACR_CTRL_TMDSCLKRATIO BIT(3)
+
+/*
+ * This list is only for formats allowed on the I2S bus. So there is
+ * some formats listed that are not supported by HDMI interface. For
+ * instance allowing the 32-bit formats enables 24-precision with CPU
+ * DAIs that do not support 24-bit formats. If the extra formats cause
+ * problems, we should add the video side driver an option to disable
+ * them.
+ */
+#define I2S_FORMATS	(SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S16_BE |\
+			 SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S20_3BE |\
+			 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_3BE |\
+			 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S24_BE |\
+			 SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_S32_BE |\
+			 SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_LE)
+#define HDMI_RATES	(SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 |\
+			 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 |\
+			 SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_176400 |\
+			 SNDRV_PCM_RATE_192000)
+
+/*
+ * CEA speaker placement for HDMI 1.4:
+ *
+ *  FL  FLC   FC   FRC   FR   FRW
+ *
+ *                                  LFE
+ *
+ *  RL  RLC   RC   RRC   RR
+ *
+ *  Speaker placement has to be extended to support HDMI 2.0
+ */
+enum hdmi_codec_cea_spk_placement {
+	FL  = BIT(0),	/* Front Left           */
+	FC  = BIT(1),	/* Front Center         */
+	FR  = BIT(2),	/* Front Right          */
+	FLC = BIT(3),	/* Front Left Center    */
+	FRC = BIT(4),	/* Front Right Center   */
+	RL  = BIT(5),	/* Rear Left            */
+	RC  = BIT(6),	/* Rear Center          */
+	RR  = BIT(7),	/* Rear Right           */
+	RLC = BIT(8),	/* Rear Left Center     */
+	RRC = BIT(9),	/* Rear Right Center    */
+	LFE = BIT(10),	/* Low Frequency Effect */
+};
+
+/*
+ * cea Speaker allocation structure
+ */
+struct hdmi_codec_cea_spk_alloc {
+	const int ca_id;
+	unsigned int n_ch;
+	unsigned long mask;
+};
+
+struct acr_n_table {
+	u32 tmds_rate;
+	u32 acr_nval[7];
+};
+
+/*
+ * hdmi_codec_channel_alloc: speaker configuration available for CEA
+ *
+ * This is an ordered list that must match with hdmi_codec_8ch_chmaps struct
+ * The preceding ones have better chances to be selected by
+ * hdmi_codec_get_ch_alloc_table_idx().
+ */
+static const struct hdmi_codec_cea_spk_alloc hdmi_codec_channel_alloc[] = {
+	{ .ca_id = 0x00, .n_ch = 2,
+	  .mask = FL | FR},
+	/* 2.1 */
+	{ .ca_id = 0x01, .n_ch = 4,
+	  .mask = FL | FR | LFE},
+	/* Dolby Surround */
+	{ .ca_id = 0x02, .n_ch = 4,
+	  .mask = FL | FR | FC },
+	/* surround51 */
+	{ .ca_id = 0x0b, .n_ch = 6,
+	  .mask = FL | FR | LFE | FC | RL | RR},
+	/* surround40 */
+	{ .ca_id = 0x08, .n_ch = 6,
+	  .mask = FL | FR | RL | RR },
+	/* surround41 */
+	{ .ca_id = 0x09, .n_ch = 6,
+	  .mask = FL | FR | LFE | RL | RR },
+	/* surround50 */
+	{ .ca_id = 0x0a, .n_ch = 6,
+	  .mask = FL | FR | FC | RL | RR },
+	/* 6.1 */
+	{ .ca_id = 0x0f, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | RC },
+	/* surround71 */
+	{ .ca_id = 0x13, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | RLC | RRC },
+	/* others */
+	{ .ca_id = 0x03, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC },
+	{ .ca_id = 0x04, .n_ch = 8,
+	  .mask = FL | FR | RC},
+	{ .ca_id = 0x05, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC },
+	{ .ca_id = 0x06, .n_ch = 8,
+	  .mask = FL | FR | FC | RC },
+	{ .ca_id = 0x07, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RC },
+	{ .ca_id = 0x0c, .n_ch = 8,
+	  .mask = FL | FR | RC | RL | RR },
+	{ .ca_id = 0x0d, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | RC },
+	{ .ca_id = 0x0e, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | RC },
+	{ .ca_id = 0x10, .n_ch = 8,
+	  .mask = FL | FR | RL | RR | RLC | RRC },
+	{ .ca_id = 0x11, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | RLC | RRC },
+	{ .ca_id = 0x12, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | RLC | RRC },
+	{ .ca_id = 0x14, .n_ch = 8,
+	  .mask = FL | FR | FLC | FRC },
+	{ .ca_id = 0x15, .n_ch = 8,
+	  .mask = FL | FR | LFE | FLC | FRC },
+	{ .ca_id = 0x16, .n_ch = 8,
+	  .mask = FL | FR | FC | FLC | FRC },
+	{ .ca_id = 0x17, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | FLC | FRC },
+	{ .ca_id = 0x18, .n_ch = 8,
+	  .mask = FL | FR | RC | FLC | FRC },
+	{ .ca_id = 0x19, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC | FLC | FRC },
+	{ .ca_id = 0x1a, .n_ch = 8,
+	  .mask = FL | FR | RC | FC | FLC | FRC },
+	{ .ca_id = 0x1b, .n_ch = 8,
+	  .mask = FL | FR | LFE | RC | FC | FLC | FRC },
+	{ .ca_id = 0x1c, .n_ch = 8,
+	  .mask = FL | FR | RL | RR | FLC | FRC },
+	{ .ca_id = 0x1d, .n_ch = 8,
+	  .mask = FL | FR | LFE | RL | RR | FLC | FRC },
+	{ .ca_id = 0x1e, .n_ch = 8,
+	  .mask = FL | FR | FC | RL | RR | FLC | FRC },
+	{ .ca_id = 0x1f, .n_ch = 8,
+	  .mask = FL | FR | LFE | FC | RL | RR | FLC | FRC },
+};
+
+/* N values for Audio Clock Regeneration */
+const struct acr_n_table acr_n_table[] = {
+	/* TMDSClk    32k   44k1   48k   88k2    96k  176k4   192k */
+	{        0, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 25200000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 27000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 31500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 33750000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 37800000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 40500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 50400000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 54000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 67500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 74250000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 81000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{ 92812500, { 8192, 6272, 12288, 12544, 24576, 25088, 49152} },
+	{108000000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{111375000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{148500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{185625000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{222750000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{297000000, { 3072, 4704,  5120,  9408, 10240, 18816, 20480} },
+	{371250000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{445500000, { 4096, 6272,  6144, 12544, 12288, 25088, 24576} },
+	{594000000, { 3072, 9408,  6144, 18816, 12288, 37632, 24576} }
+};
+
+static u16 srate_to_index(u32 srate)
+{
+	u16 index;
+
+	switch (srate) {
+	case 32000:
+		index = 0;
+	break;
+	case 44100:
+		index = 1;
+	break;
+	case 48000:
+		index = 2;
+	break;
+	case 88200:
+		index = 3;
+	break;
+	case 96000:
+		index = 4;
+	break;
+	case 176400:
+		index = 5;
+	break;
+	case 192000:
+		index = 6;
+	break;
+	default:
+		index = 0;
+	break;
+	}
+
+	return index;
+}
+
+/* xhdmi_acr_get_n - calculate N value from lookup table
+ * @tmds_rate: TMDS clock
+ * @srate: sampling rate
+ *
+ * This function retrieves N value from the lookup table using
+ * TMDS clock and sampling rate
+ *
+ * Return: N value
+ */
+static const unsigned int xhdmi_acr_get_n(unsigned int tmds_rate, int srate)
+{
+	struct acr_n_table const *item;
+	u16 i, idx;
+
+	for (i = 0; i < sizeof(acr_n_table)/sizeof(struct acr_n_table); i++) {
+		item = &acr_n_table[i];
+		if (item->tmds_rate == tmds_rate) {
+			idx = srate_to_index(srate);
+			return item->acr_nval[idx];
+		}
+	}
+
+	/* if not found return default */
+	item = &acr_n_table[0];
+	idx = srate_to_index(srate);
+	return item->acr_nval[idx];
+}
+
+/* hdmitx_parse_aud_dt - parse ACR node from DT
+ * @dev: device
+ *
+ * Parse the DT entry related to ACR IP.
+ */
+void __iomem *hdmitx_parse_aud_dt(struct device *dev)
+{
+	int rc;
+	struct device_node *node, *acr_node;
+	void __iomem *acr_base;
+	struct resource acr_res;
+
+	node = dev->of_node;
+	acr_node = of_parse_phandle(node, "xlnx,xlnx-hdmi-acr-ctrl", 0);
+	if (!acr_node) {
+		dev_err(dev, "failed to get acr_node!\n");
+		acr_base = NULL;
+	} else {
+		rc = of_address_to_resource(acr_node, 0, &acr_res);
+		if (rc) {
+			dev_err(dev, "acr resource failed: %d\n", rc);
+			acr_base = NULL;
+		} else {
+			acr_base = devm_ioremap_resource(dev, &acr_res);
+			if (IS_ERR(acr_base)) {
+				dev_err(dev, "acr ioremap failed\n");
+				acr_base = NULL;
+			}
+		}
+		of_node_put(acr_node);
+	}
+	return acr_base;
+}
+
+static unsigned long hdmi_codec_spk_mask_from_alloc(int spk_alloc)
+{
+	int i;
+	static const unsigned long hdmi_codec_eld_spk_alloc_bits[] = {
+		[0] = FL | FR, [1] = LFE, [2] = FC, [3] = RL | RR,
+		[4] = RC, [5] = FLC | FRC, [6] = RLC | RRC,
+	};
+	unsigned long spk_mask = 0;
+
+	for (i = 0; i < ARRAY_SIZE(hdmi_codec_eld_spk_alloc_bits); i++) {
+		if (spk_alloc & (1 << i))
+			spk_mask |= hdmi_codec_eld_spk_alloc_bits[i];
+	}
+
+	return spk_mask;
+}
+
+static int hdmi_codec_get_ch_alloc_table_idx(u8 *eld, u8 channels)
+{
+	int i;
+	u8 spk_alloc;
+	unsigned long spk_mask;
+	const struct hdmi_codec_cea_spk_alloc *cap = hdmi_codec_channel_alloc;
+
+	spk_alloc = drm_eld_get_spk_alloc(eld);
+	spk_mask = hdmi_codec_spk_mask_from_alloc(spk_alloc);
+
+	for (i = 0; i < ARRAY_SIZE(hdmi_codec_channel_alloc); i++, cap++) {
+		/* If spk_alloc == 0, HDMI is unplugged return stereo config*/
+		if (!spk_alloc && cap->ca_id == 0)
+			return i;
+		if (cap->n_ch != channels)
+			continue;
+		if (!(cap->mask == (spk_mask & cap->mask)))
+			continue;
+		return i;
+	}
+
+	return -EINVAL;
+}
+
+static int hdmi_codec_fill_cea_params(struct snd_pcm_substream *substream,
+				      struct snd_soc_dai *dai,
+				      unsigned int channels,
+				      struct hdmi_audio_infoframe *cea)
+{
+	int idx;
+	int ret;
+	u8 eld[MAX_ELD_BYTES];
+
+	ret = hdmitx_audio_geteld(dai->dev, eld, sizeof(eld));
+	if (ret)
+		return ret;
+
+	ret = snd_pcm_hw_constraint_eld(substream->runtime, eld);
+	if (ret)
+		return ret;
+
+	/* Select a channel allocation that matches with ELD and pcm channels */
+	idx = hdmi_codec_get_ch_alloc_table_idx(eld, channels);
+	if (idx < 0) {
+		dev_err(dai->dev, "Not able to map channels to speakers (%d)\n",
+			idx);
+		return idx;
+	}
+
+	hdmi_audio_infoframe_init(cea);
+	cea->channels = channels;
+	cea->coding_type = HDMI_AUDIO_CODING_TYPE_STREAM;
+	cea->sample_size = HDMI_AUDIO_SAMPLE_SIZE_STREAM;
+	cea->sample_frequency = HDMI_AUDIO_SAMPLE_FREQUENCY_STREAM;
+	cea->channel_allocation = hdmi_codec_channel_alloc[idx].ca_id;
+
+	return 0;
+}
+
+/* xlnx_tx_pcm_startup - initialize audio during audio usecase
+ *
+ * This function is called by ALSA framework before audio
+ * playback begins. This callback initializes audio
+ *
+ * Return: 0 on success
+ */
+static int xlnx_tx_pcm_startup(struct snd_pcm_substream *substream,
+			       struct snd_soc_dai *dai)
+{
+	hdmitx_audio_startup(dai->dev);
+
+	return 0;
+}
+
+/* xlnx_tx_pcm_hw_params - sets the playback stream properties
+ * @dev: device
+ * @data: optional data set during registration
+ * @fmt: Protocol between ASoC cpu-dai and HDMI-encoder
+ * @hparams: stream parameters
+ *
+ * This function is called by ALSA framework after startup callback
+ * packs the audio infoframe from stream paremters and programs ACR
+ * block
+ *
+ * Return: 0 on success
+ */
+static int xlnx_tx_pcm_hw_params(struct snd_pcm_substream *substream,
+				 struct snd_pcm_hw_params *params,
+				 struct snd_soc_dai *dai)
+{
+	u32 n, val;
+	int ret;
+	struct hdmi_audio_infoframe frame;
+	struct xlnx_hdmitx_audio_data *adata = hdmitx_get_audio_data(dai->dev);
+
+	if (!adata)
+		return -EINVAL;
+
+	ret = hdmi_codec_fill_cea_params(substream, dai,
+					 params_channels(params),
+					 &frame);
+	if (ret < 0)
+		return ret;
+
+	hdmitx_audio_hw_params(dai->dev, &frame);
+	hdmi_audio_infoframe_pack(&frame, adata->buffer,
+				  HDMI_INFOFRAME_SIZE(AUDIO));
+
+	n = xhdmi_acr_get_n(adata->tmds_clk, params_rate(params));
+
+	/* Disable ACR */
+	writel(2, adata->acr_base + XV_ACR_ENABLE);
+	/* program 'N' */
+	writel(n, adata->acr_base + XV_ACR_N);
+
+	val = 3;
+	if (adata->tmds_clk_ratio)
+		val |= ACR_CTRL_TMDSCLKRATIO;
+
+	/* Enable ACR */
+	writel(val, adata->acr_base + XV_ACR_ENABLE);
+
+	return 0;
+}
+
+/* xlnx_tx_pcm_shutdown - Deinitialze audio when audio usecase is stopped
+ *
+ * This function is called by ALSA framework before audio playback usecase
+ * ends.
+ */
+static void xlnx_tx_pcm_shutdown(struct snd_pcm_substream *substream,
+				 struct snd_soc_dai *dai)
+{
+	hdmitx_audio_shutdown(dai->dev);
+}
+
+/* xlnx_tx_pcm_digital_mute - mute or unmute audio
+ *
+ * This function is called by ALSA framework before audio usecase
+ * starts and before audio usecase ends
+ */
+static int xlnx_tx_pcm_digital_mute(struct snd_soc_dai *dai, int enable,
+				    int direction)
+{
+	hdmitx_audio_mute(dai->dev, enable);
+
+	return 0;
+}
+
+int xlnx_tx_pcm_get_eld(struct device *dev, void *data,
+			uint8_t *buf, size_t len)
+{
+	return hdmitx_audio_geteld(dev, buf, len);
+}
+
+static const struct snd_soc_dai_ops xlnx_hdmi_tx_dai_ops = {
+	.startup = xlnx_tx_pcm_startup,
+	.hw_params = xlnx_tx_pcm_hw_params,
+	.shutdown = xlnx_tx_pcm_shutdown,
+	.mute_stream = xlnx_tx_pcm_digital_mute,
+	.no_capture_mute = 1,
+};
+
+static struct snd_soc_dai_driver xlnx_hdmi_tx_dai = {
+	.name = "xlnx_hdmi_tx",
+	.playback = {
+		.stream_name = "I2S Playback",
+		.channels_min = 2,
+		.channels_max = 8,
+		.rates = HDMI_RATES,
+		.formats = I2S_FORMATS,
+		.sig_bits = 24,
+	},
+	.ops = &xlnx_hdmi_tx_dai_ops,
+};
+
+static int xlnx_tx_codec_probe(struct snd_soc_component *component)
+{
+	return 0;
+}
+
+void xlnx_tx_codec_remove(struct snd_soc_component *component)
+{
+}
+
+static const struct snd_soc_component_driver xlnx_hdmi_component = {
+	.probe = xlnx_tx_codec_probe,
+	.remove = xlnx_tx_codec_remove,
+};
+
+int hdmitx_register_aud_dev(struct device *dev, int instance)
+{
+	return devm_snd_soc_register_component(dev, &xlnx_hdmi_component,
+			&xlnx_hdmi_tx_dai, 1);
+}
+
+void hdmitx_unregister_aud_dev(struct device *dev)
+{
+	snd_soc_unregister_component(dev);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmitx_audio.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/hdmi/xlnx_hdmitx_audio.h
@@ -0,0 +1,38 @@
+/*
+ * Xilinx ALSA SoC HDMI audio playback support
+ *
+ * Copyright (C) 2017-2018 Xilinx, Inc.
+ *
+ * Author: Maruthi Srinivas Bayyavarapu <maruthis@xilinx.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __XILINX_HDMI_TX_AUD_H__
+#define __XILINX_HDMI_TX_AUD_H__
+struct xlnx_hdmitx_audio_data {
+	u8 buffer[HDMI_INFOFRAME_SIZE(AUDIO)];
+	unsigned int tmds_clk;
+	void __iomem *acr_base;
+	bool tmds_clk_ratio;
+};
+
+struct xlnx_hdmitx_audio_data *hdmitx_get_audio_data(struct device *dev);
+void __iomem *hdmitx_parse_aud_dt(struct device *dev);
+int hdmitx_register_aud_dev(struct device *dev, int instance);
+void hdmitx_unregister_aud_dev(struct device *dev);
+void hdmitx_audio_startup(struct device *dev);
+void hdmitx_audio_hw_params(struct device *dev,
+		struct hdmi_audio_infoframe *frame);
+void hdmitx_audio_shutdown(struct device *dev);
+void hdmitx_audio_mute(struct device *dev, bool enable);
+int hdmitx_audio_geteld(struct device *dev, uint8_t *buf, size_t len);
+
+#endif /* __XILINX_HDMI_TX_AUD_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/misc/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/misc/Makefile
@@ -0,0 +1,2 @@
+obj-m    += dp159.o
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-hdmi/misc/dp159.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-hdmi/misc/dp159.c
@@ -0,0 +1,229 @@
+/*
+ * dp159 redriver and retimer
+ * Copyright (C) 2016, 2017 Leon Woestenberg <leon@sidebranch.com>
+ *
+ * based on code
+ * Copyright (C) 2007 Hans Verkuil
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/of.h>
+#include <linux/of.h>
+#include <linux/clk-provider.h>
+
+MODULE_DESCRIPTION("i2c device driver for dp159 redriver and retimer");
+MODULE_AUTHOR("Leon Woestenberg");
+MODULE_LICENSE("GPL");
+
+static bool debug;
+
+module_param(debug, bool, 0644);
+
+MODULE_PARM_DESC(debug, "Debugging messages, 0=Off (default), 1=On");
+
+struct clk_tx_linerate {
+	struct clk_hw hw;
+	struct i2c_client *client;
+	struct clk *clk;
+	unsigned long rate;
+};
+
+static inline int dp159_write(struct i2c_client *client, u8 reg, u8 value)
+{
+	int rc;
+	rc = i2c_smbus_write_byte_data(client, reg, value);
+	return rc;
+}
+
+static inline int dp159_read(struct i2c_client *client, u8 reg)
+{
+
+	return i2c_smbus_read_byte_data(client, reg);
+}
+
+static int dp159_program(struct i2c_client *client, unsigned long rate)
+{
+	int r;
+	r = dp159_write(client, 0x09, 0x06);
+
+	if ((rate / (1000000)) > 3400) {
+//		printk(KERN_INFO "dp159_program(rate = %lu) for HDMI 2.0\n", rate);
+		/* SLEW_CTL    = Reg0Bh[7:6] = 10
+		 * TX_TERM_CTL = Reg0Bh[4:3] = 11
+		*/
+		r |= dp159_write(client, 0x0B, 0x9A);
+
+		/*
+		 * Set the 0x0C register to
+		 * - increase VSWING_DATA and VSWING_CLK by 14%.
+		 * - set HDMI_TWPST1 to 2 dB de-emphasis.
+		 * Refer to DP159 datasheet below for details
+		 * https://www.ti.com/lit/ds/symlink/sn65dp159.pdf
+		 */
+		r |= dp159_write(client, 0x0C, 0x49);
+		r |= dp159_write(client, 0x0D, 0x00);
+		r |= dp159_write(client, 0x0A, 0x36); // Automatic retimer for HDMI 2.0
+	} else {
+//		printk(KERN_INFO "dp159_program(rate = %lu) for HDMI 1.4\n", rate);
+		/*datasheet has 0 by default. 0x1 disables DDC training and only
+		 * allows HDMI1.4b/DVI, which is OK*/
+
+		r |= dp159_write(client, 0x0B, 0x80); // SLEW_CTL    = Reg0Bh[7:6] = 10
+                                              // TX_TERM_CTL = Reg0Bh[4:3] = 00
+		// VSWING_DATA & VSWING_CLK to +14%
+		//           Reg0Ch[7:2] = 100100
+		// PRE_SEL = Reg0Ch[1:0] = 00 (labeled HDMI_TWPST)
+		r |= dp159_write(client, 0x0C, 0x48);
+		r |= dp159_write(client, 0x0D, 0x00);
+        // Automatic redriver to retimer crossover at 1.0 Gbps
+		r |= dp159_write(client, 0x0A, 0x35);
+	}
+	return r;
+}
+
+#define to_clk_tx_linerate(_hw) container_of(_hw, struct clk_tx_linerate, hw)
+
+int clk_tx_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate)
+{
+	struct clk_tx_linerate *clk;
+	clk = to_clk_tx_linerate(hw);
+	//printk(KERN_INFO "dp159: clk_tx_set_rate(): rate = %lu, parent_rate = %lu\n", rate, parent_rate);
+	clk->rate = rate;
+	dp159_program(clk->client, rate);
+	return 0;
+};
+
+unsigned long clk_tx_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+	struct clk_tx_linerate *clk;
+	clk = to_clk_tx_linerate(hw);
+	//printk(KERN_INFO "dp159: clk_tx_recalc_rate(): parent_rate = %lu\n", parent_rate);
+	return clk->rate;
+};
+
+long clk_tx_round_rate(struct clk_hw *hw,
+	unsigned long rate,	unsigned long *parent_rate)
+{
+	struct clk_tx_linerate *clk;
+	clk = to_clk_tx_linerate(hw);
+	return rate;
+};
+
+struct clk_ops clk_tx_rate_ops = {
+	.set_rate 		= &clk_tx_set_rate,
+	.recalc_rate	= &clk_tx_recalc_rate,
+	.round_rate		= &clk_tx_round_rate,
+};
+
+static int dp159_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct clk_tx_linerate *clk_tx;
+	struct clk *clk;
+	struct clk_init_data init;
+	int ret;
+
+	/* Check if the adapter supports the needed features */
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+		return -EIO;
+
+	if ((dp159_read(client, 0) != 'D') || (dp159_read(client, 1) != 'P')) {
+		dev_err(&client->dev, "Identification registers do not indicate DP159 presence.\n");
+		return -ENODEV;
+	}
+
+	dev_info(&client->dev, "probed\n");
+	/* initialize to HDMI 1.4 */
+	(void)dp159_write(client, 0x0B, 0x80);
+	(void)dp159_write(client, 0x0C, 0x48);
+	(void)dp159_write(client, 0x0D, 0x00);
+	(void)dp159_write(client, 0x0A, 0x35);
+
+	/* allocate fixed-rate clock */
+	clk_tx = kzalloc(sizeof(*clk_tx), GFP_KERNEL);
+	if (!clk_tx)
+		return -ENOMEM;
+
+	init.name = dev_name(&client->dev);
+	init.ops = &clk_tx_rate_ops;
+	init.flags = 0; ///*flags | CLK_IS_BASIC*/;
+	init.parent_names = NULL;
+	init.num_parents = 0;
+
+	clk_tx->hw.init = &init;
+
+	/* register the clock */
+	clk = clk_register(&client->dev, &clk_tx->hw);
+	if (IS_ERR(clk)) {
+		kfree(clk_tx);
+		return PTR_ERR(clk);
+	}
+	/* reference to client in clock */
+	clk_tx->client = client;
+	clk_tx->clk = clk;
+	/* reference to clk_tx in client */
+	i2c_set_clientdata(client, (void *)clk_tx);
+	//dev_info(&client->dev, "DP159 retimer.\n");
+
+	ret = of_clk_add_provider(client->dev.of_node, of_clk_src_simple_get,
+		to_clk_tx_linerate(&clk_tx->hw));
+	if (ret) {
+		dev_err(&client->dev, "unable to add clk provider\n");
+	}
+	dev_info(&client->dev, "probe successful\n");
+	return 0;
+}
+
+static int dp159_remove(struct i2c_client *client)
+{
+	struct clk_tx_linerate *clk_tx;
+	clk_tx = (struct clk_tx_linerate *)i2c_get_clientdata(client);
+	if (clk_tx)
+		clk_unregister(clk_tx->clk);
+	return 0;
+}
+
+static const struct i2c_device_id dp159_id[] = {
+	{ "dp159", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, dp159_id);
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id dp159_of_match[] = {
+        { .compatible = "ti,dp159", },
+        { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, dp159_of_match);
+#endif
+
+static struct i2c_driver dp159_driver = {
+	.driver = {
+		.owner = THIS_MODULE,
+		.name	= "dp159",
+		.of_match_table = of_match_ptr(dp159_of_match),
+	},
+	.probe		= dp159_probe,
+	.remove		= dp159_remove,
+	.id_table	= dp159_id,
+};
+
+module_i2c_driver(dp159_driver);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-isp-module/LICENSE.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-isp-module/LICENSE.md
@@ -0,0 +1,342 @@
+		    GNU GENERAL PUBLIC LICENSE
+		       Version 2, June 1991
+
+ Copyright (C) 1989, 1991 Free Software Foundation, Inc.
+                       51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+			    Preamble
+
+  The licenses for most software are designed to take away your
+freedom to share and change it.  By contrast, the GNU General Public
+License is intended to guarantee your freedom to share and change free
+software--to make sure the software is free for all its users.  This
+General Public License applies to most of the Free Software
+Foundation's software and to any other program whose authors commit to
+using it.  (Some other Free Software Foundation software is covered by
+the GNU Library General Public License instead.)  You can apply it to
+your programs, too.
+
+  When we speak of free software, we are referring to freedom, not
+price.  Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+this service if you wish), that you receive source code or can get it
+if you want it, that you can change the software or use pieces of it
+in new free programs; and that you know you can do these things.
+
+  To protect your rights, we need to make restrictions that forbid
+anyone to deny you these rights or to ask you to surrender the rights.
+These restrictions translate to certain responsibilities for you if you
+distribute copies of the software, or if you modify it.
+
+  For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must give the recipients all the rights that
+you have.  You must make sure that they, too, receive or can get the
+source code.  And you must show them these terms so they know their
+rights.
+
+  We protect your rights with two steps: (1) copyright the software, and
+(2) offer you this license which gives you legal permission to copy,
+distribute and/or modify the software.
+
+  Also, for each author's protection and ours, we want to make certain
+that everyone understands that there is no warranty for this free
+software.  If the software is modified by someone else and passed on, we
+want its recipients to know that what they have is not the original, so
+that any problems introduced by others will not reflect on the original
+authors' reputations.
+
+  Finally, any free program is threatened constantly by software
+patents.  We wish to avoid the danger that redistributors of a free
+program will individually obtain patent licenses, in effect making the
+program proprietary.  To prevent this, we have made it clear that any
+patent must be licensed for everyone's free use or not licensed at all.
+
+  The precise terms and conditions for copying, distribution and
+modification follow.
+
+		    GNU GENERAL PUBLIC LICENSE
+   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
+
+  0. This License applies to any program or other work which contains
+a notice placed by the copyright holder saying it may be distributed
+under the terms of this General Public License.  The "Program", below,
+refers to any such program or work, and a "work based on the Program"
+means either the Program or any derivative work under copyright law:
+that is to say, a work containing the Program or a portion of it,
+either verbatim or with modifications and/or translated into another
+language.  (Hereinafter, translation is included without limitation in
+the term "modification".)  Each licensee is addressed as "you".
+
+Activities other than copying, distribution and modification are not
+covered by this License; they are outside its scope.  The act of
+running the Program is not restricted, and the output from the Program
+is covered only if its contents constitute a work based on the
+Program (independent of having been made by running the Program).
+Whether that is true depends on what the Program does.
+
+  1. You may copy and distribute verbatim copies of the Program's
+source code as you receive it, in any medium, provided that you
+conspicuously and appropriately publish on each copy an appropriate
+copyright notice and disclaimer of warranty; keep intact all the
+notices that refer to this License and to the absence of any warranty;
+and give any other recipients of the Program a copy of this License
+along with the Program.
+
+You may charge a fee for the physical act of transferring a copy, and
+you may at your option offer warranty protection in exchange for a fee.
+
+  2. You may modify your copy or copies of the Program or any portion
+of it, thus forming a work based on the Program, and copy and
+distribute such modifications or work under the terms of Section 1
+above, provided that you also meet all of these conditions:
+
+    a) You must cause the modified files to carry prominent notices
+    stating that you changed the files and the date of any change.
+
+    b) You must cause any work that you distribute or publish, that in
+    whole or in part contains or is derived from the Program or any
+    part thereof, to be licensed as a whole at no charge to all third
+    parties under the terms of this License.
+
+    c) If the modified program normally reads commands interactively
+    when run, you must cause it, when started running for such
+    interactive use in the most ordinary way, to print or display an
+    announcement including an appropriate copyright notice and a
+    notice that there is no warranty (or else, saying that you provide
+    a warranty) and that users may redistribute the program under
+    these conditions, and telling the user how to view a copy of this
+    License.  (Exception: if the Program itself is interactive but
+    does not normally print such an announcement, your work based on
+    the Program is not required to print an announcement.)
+
+These requirements apply to the modified work as a whole.  If
+identifiable sections of that work are not derived from the Program,
+and can be reasonably considered independent and separate works in
+themselves, then this License, and its terms, do not apply to those
+sections when you distribute them as separate works.  But when you
+distribute the same sections as part of a whole which is a work based
+on the Program, the distribution of the whole must be on the terms of
+this License, whose permissions for other licensees extend to the
+entire whole, and thus to each and every part regardless of who wrote it.
+
+Thus, it is not the intent of this section to claim rights or contest
+your rights to work written entirely by you; rather, the intent is to
+exercise the right to control the distribution of derivative or
+collective works based on the Program.
+
+In addition, mere aggregation of another work not based on the Program
+with the Program (or with a work based on the Program) on a volume of
+a storage or distribution medium does not bring the other work under
+the scope of this License.
+
+  3. You may copy and distribute the Program (or a work based on it,
+under Section 2) in object code or executable form under the terms of
+Sections 1 and 2 above provided that you also do one of the following:
+
+    a) Accompany it with the complete corresponding machine-readable
+    source code, which must be distributed under the terms of Sections
+    1 and 2 above on a medium customarily used for software interchange; or,
+
+    b) Accompany it with a written offer, valid for at least three
+    years, to give any third party, for a charge no more than your
+    cost of physically performing source distribution, a complete
+    machine-readable copy of the corresponding source code, to be
+    distributed under the terms of Sections 1 and 2 above on a medium
+    customarily used for software interchange; or,
+
+    c) Accompany it with the information you received as to the offer
+    to distribute corresponding source code.  (This alternative is
+    allowed only for noncommercial distribution and only if you
+    received the program in object code or executable form with such
+    an offer, in accord with Subsection b above.)
+
+The source code for a work means the preferred form of the work for
+making modifications to it.  For an executable work, complete source
+code means all the source code for all modules it contains, plus any
+associated interface definition files, plus the scripts used to
+control compilation and installation of the executable.  However, as a
+special exception, the source code distributed need not include
+anything that is normally distributed (in either source or binary
+form) with the major components (compiler, kernel, and so on) of the
+operating system on which the executable runs, unless that component
+itself accompanies the executable.
+
+If distribution of executable or object code is made by offering
+access to copy from a designated place, then offering equivalent
+access to copy the source code from the same place counts as
+distribution of the source code, even though third parties are not
+compelled to copy the source along with the object code.
+
+  4. You may not copy, modify, sublicense, or distribute the Program
+except as expressly provided under this License.  Any attempt
+otherwise to copy, modify, sublicense or distribute the Program is
+void, and will automatically terminate your rights under this License.
+However, parties who have received copies, or rights, from you under
+this License will not have their licenses terminated so long as such
+parties remain in full compliance.
+
+  5. You are not required to accept this License, since you have not
+signed it.  However, nothing else grants you permission to modify or
+distribute the Program or its derivative works.  These actions are
+prohibited by law if you do not accept this License.  Therefore, by
+modifying or distributing the Program (or any work based on the
+Program), you indicate your acceptance of this License to do so, and
+all its terms and conditions for copying, distributing or modifying
+the Program or works based on it.
+
+  6. Each time you redistribute the Program (or any work based on the
+Program), the recipient automatically receives a license from the
+original licensor to copy, distribute or modify the Program subject to
+these terms and conditions.  You may not impose any further
+restrictions on the recipients' exercise of the rights granted herein.
+You are not responsible for enforcing compliance by third parties to
+this License.
+
+  7. If, as a consequence of a court judgment or allegation of patent
+infringement or for any other reason (not limited to patent issues),
+conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License.  If you cannot
+distribute so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you
+may not distribute the Program at all.  For example, if a patent
+license would not permit royalty-free redistribution of the Program by
+all those who receive copies directly or indirectly through you, then
+the only way you could satisfy both it and this License would be to
+refrain entirely from distribution of the Program.
+
+If any portion of this section is held invalid or unenforceable under
+any particular circumstance, the balance of the section is intended to
+apply and the section as a whole is intended to apply in other
+circumstances.
+
+It is not the purpose of this section to induce you to infringe any
+patents or other property right claims or to contest validity of any
+such claims; this section has the sole purpose of protecting the
+integrity of the free software distribution system, which is
+implemented by public license practices.  Many people have made
+generous contributions to the wide range of software distributed
+through that system in reliance on consistent application of that
+system; it is up to the author/donor to decide if he or she is willing
+to distribute software through any other system and a licensee cannot
+impose that choice.
+
+This section is intended to make thoroughly clear what is believed to
+be a consequence of the rest of this License.
+
+  8. If the distribution and/or use of the Program is restricted in
+certain countries either by patents or by copyrighted interfaces, the
+original copyright holder who places the Program under this License
+may add an explicit geographical distribution limitation excluding
+those countries, so that distribution is permitted only in or among
+countries not thus excluded.  In such case, this License incorporates
+the limitation as if written in the body of this License.
+
+  9. The Free Software Foundation may publish revised and/or new versions
+of the General Public License from time to time.  Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+Each version is given a distinguishing version number.  If the Program
+specifies a version number of this License which applies to it and "any
+later version", you have the option of following the terms and conditions
+either of that version or of any later version published by the Free
+Software Foundation.  If the Program does not specify a version number of
+this License, you may choose any version ever published by the Free Software
+Foundation.
+
+  10. If you wish to incorporate parts of the Program into other free
+programs whose distribution conditions are different, write to the author
+to ask for permission.  For software which is copyrighted by the Free
+Software Foundation, write to the Free Software Foundation; we sometimes
+make exceptions for this.  Our decision will be guided by the two goals
+of preserving the free status of all derivatives of our free software and
+of promoting the sharing and reuse of software generally.
+
+			    NO WARRANTY
+
+  11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
+FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.  EXCEPT WHEN
+OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
+PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
+OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRE RISK AS
+TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.  SHOULD THE
+PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
+REPAIR OR CORRECTION.
+
+  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
+REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
+INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
+OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
+TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
+YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
+PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGES.
+
+		     END OF TERMS AND CONDITIONS
+
+	    How to Apply These Terms to Your New Programs
+
+  If you develop a new program, and you want it to be of the greatest
+possible use to the public, the best way to achieve this is to make it
+free software which everyone can redistribute and change under these terms.
+
+  To do so, attach the following notices to the program.  It is safest
+to attach them to the start of each source file to most effectively
+convey the exclusion of warranty; and each file should have at least
+the "copyright" line and a pointer to where the full notice is found.
+
+    <one line to give the program's name and a brief idea of what it does.>
+    Copyright (C) <year>  <name of author>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+Also add information on how to contact you by electronic and paper mail.
+
+If the program is interactive, make it output a short notice like this
+when it starts in an interactive mode:
+
+    Gnomovision version 69, Copyright (C) year name of author
+    Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
+    This is free software, and you are welcome to redistribute it
+    under certain conditions; type `show c' for details.
+
+The hypothetical commands `show w' and `show c' should show the appropriate
+parts of the General Public License.  Of course, the commands you use may
+be called something other than `show w' and `show c'; they could even be
+mouse-clicks or menu items--whatever suits your program.
+
+You should also get your employer (if you work as a programmer) or your
+school, if any, to sign a "copyright disclaimer" for the program, if
+necessary.  Here is a sample; alter the names:
+
+  Yoyodyne, Inc., hereby disclaims all copyright interest in the program
+  `Gnomovision' (which makes passes at compilers) written by James Hacker.
+
+  <signature of Ty Coon>, 1 April 1989
+  Ty Coon, President of Vice
+
+This General Public License does not permit incorporating your program into
+proprietary programs.  If your program is a subroutine library, you may
+consider it more useful to permit linking proprietary applications with the
+library.  If this is what you want to do, use the GNU Library General
+Public License instead of this License.
+
+Copyright (C) 2022 Xilinx.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-isp-module/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-isp-module/Makefile
@@ -0,0 +1,39 @@
+#
+# Copyright (c) 2022. Xilinx.  All rights reserved.
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms and conditions of the GNU General Public License,
+# version 2, as published by the Free Software Foundation.
+#
+# This program is distributed in the hope it will be useful, but WITHOUT
+# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+# FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+# more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+#
+
+SRC := $(shell pwd)
+
+obj-m += xilinx-isppipeline.o
+##CFLAGS_xilinx-isppipeline.o += -I/usr/src/linux-xilinx-zynqmp-headers-5.15.0-1003/include/
+
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/include/linux
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/generated/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/generated/uapi/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/uapi/
+
+all:
+	$(MAKE) -C $(KERNEL_SRC) M=$(PWD) modules
+
+modules_install:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules_install
+
+clean:
+	rm -f *.o *~ core .depend .*.cmd *.ko *.mod.c
+	rm -f Module.markers Module.symvers modules.order modules.builtin
+	rm -f */*.ko */*.mod.c */.*.mod.c */.*.cmd */*.o
+	rm -f */modules.order */modules.builtin
+	rm -rf .tmp_versions Modules.symvers
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-isp-module/README.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-isp-module/README.md
@@ -0,0 +1,7 @@
+# xilinx-isppipeline
+This is a V4L sub-device based driver for Vitis Vision ISP pipeline that takes a Bayer video stream format as input and generates an RGB video output.
+
+# License
+
+(C) Copyright 2020 - 2022 Xilinx, Inc.\
+SPDX-License-Identifier: GPL-2.0
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-isp-module/xilinx-isppipeline.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-isp-module/xilinx-isppipeline.c
@@ -0,0 +1,500 @@
+/*
+ * Xilinx ISP IP
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+
+#include "xilinx-vip.h"
+
+#define XDEMOSAIC_AP_CTRL			(0x00)
+#define XDEMOSAIC_WIDTH				(0x10)
+#define XDEMOSAIC_HEIGHT			(0x18)
+#define XDEMOSAIC_RGAIN			    (0x30)
+#define XDEMOSAIC_BGAIN			    (0x38)
+#define XDEMOSAIC_MODE_REG          (0x20)
+#define XDEMOSAIC_PAWB              (0x54)
+#define XDEMOSAIC_GAMMA_LUT         (0x0800)
+#define XDEMOSAIC_INPUT_BAYER_FORMAT		(0x28)
+
+#define XDEMOSAIC_MIN_HEIGHT	(64)
+#define XDEMOSAIC_MAX_HEIGHT	(4320)
+#define XDEMOSAIC_DEF_HEIGHT	(720)
+#define XDEMOSAIC_MIN_WIDTH	(64)
+#define XDEMOSAIC_MAX_WIDTH	(8192)
+#define XDEMOSAIC_DEF_WIDTH	(1280)
+
+#define XDEMOSAIC_RESET_DEASSERT	(0)
+#define XDEMOSAIC_RESET_ASSERT		(1)
+#define XDEMOSAIC_START			BIT(0)
+#define XDEMOSAIC_AUTO_RESTART		BIT(7)
+#define XDEMOSAIC_STREAM_ON	(XDEMOSAIC_AUTO_RESTART | XDEMOSAIC_START)
+
+enum xdmsc_bayer_format {
+	XDEMOSAIC_RGGB = 0,
+	XDEMOSAIC_GRBG,
+	XDEMOSAIC_GBRG,
+	XDEMOSAIC_BGGR,
+};
+
+struct xdmsc_dev {
+	struct xvip_device xvip;
+	struct media_pad pads[2];
+	struct v4l2_mbus_framefmt formats[2];
+	struct v4l2_mbus_framefmt default_formats[2];
+
+	enum xdmsc_bayer_format bayer_fmt;
+	struct gpio_desc *rst_gpio;
+	u32 max_width;
+	u32 max_height;
+	u32 rgain;
+    u32 bgain;
+	const u8 *gamma_lut;
+    u32 mode_reg;
+    u32 pawb;
+};
+
+static inline u32 xdmsc_read(struct xdmsc_dev *xdmsc, u32 reg)
+{
+	u32 data;
+
+	data = xvip_read(&xdmsc->xvip, reg);
+	dev_dbg(xdmsc->xvip.dev,
+		"Reading 0x%x from reg offset 0x%x", data, reg);
+	return data;
+}
+
+static inline void xdmsc_write(struct xdmsc_dev *xdmsc, u32 reg, u32 data)
+{
+	xvip_write(&xdmsc->xvip, reg, data);
+	dev_dbg(xdmsc->xvip.dev,
+		"Writing 0x%x to reg offset 0x%x", data, reg);
+#ifdef DEBUG
+	if (xdmsc_read(xdmsc, reg) != data)
+		dev_err(xdmsc->xvip.dev,
+			"Wrote 0x%x does not match read back", data);
+#endif
+}
+
+static inline struct xdmsc_dev *to_xdmsc(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct xdmsc_dev, xvip.subdev);
+}
+
+static struct v4l2_mbus_framefmt
+*__xdmsc_get_pad_format(struct xdmsc_dev *xdmsc,
+			struct v4l2_subdev_state *sd_state,
+			unsigned int pad, u32 which)
+{
+	struct v4l2_mbus_framefmt *get_fmt;
+
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		get_fmt = v4l2_subdev_get_try_format(&xdmsc->xvip.subdev,
+						     sd_state, pad);
+		break;
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		get_fmt = &xdmsc->formats[pad];
+		break;
+	default:
+		get_fmt = NULL;
+		break;
+	}
+
+	return get_fmt;
+}
+
+//corrections
+static void xdmsc_set_lut_entries(struct xdmsc_dev *xdmsc,
+			       const u32 lut_base, const u8 *lut)
+{
+	int itr;
+	u32 lut_offset, lut_data;
+
+	lut_offset = lut_base;
+
+	for (itr = 0; itr < 768; itr=itr+4) {
+		lut_data = (lut[itr+3] << 24) | (lut[itr+2] << 16) | (lut[itr+1] << 8) | lut[itr];
+		xdmsc_write(xdmsc, lut_offset, lut_data);
+		lut_offset += 4;
+	}
+}
+
+static int xdmsc_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+
+	if (!enable) {
+		dev_dbg(xdmsc->xvip.dev, "%s : Off", __func__);
+		gpiod_set_value_cansleep(xdmsc->rst_gpio,
+					 XDEMOSAIC_RESET_ASSERT);
+		gpiod_set_value_cansleep(xdmsc->rst_gpio,
+					 XDEMOSAIC_RESET_DEASSERT);
+		return 0;
+	}
+
+	//u32 rgain = 156; u32 bgain=140;
+
+	//u32 pawb =256;
+
+	u8 gamma_lut[768]={0,6,10,13,15,18,20,23,25,27,29,31,33,35,36,38,40,41,43,45,46,48,49,51,52,54,55,57,58,59,61,62,63,65,66,67,69,70,71,72,74,75,76,77,79,80,81,82,83,84,86,87,88,89,90,91,92,93,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,132,133,134,135,136,137,138,139,140,141,142,142,143,144,145,146,147,148,149,149,150,151,152,153,154,155,155,156,157,158,159,160,161,161,162,163,164,165,166,166,167,168,169,170,170,171,172,173,174,175,175,176,177,178,179,179,180,181,182,182,183,184,185,186,186,187,188,189,189,190,191,192,193,193,194,195,196,196,197,198,199,199,200,201,202,202,203,204,205,205,206,207,208,208,209,210,211,211,212,213,213,214,215,216,216,217,218,219,219,220,221,221,222,223,224,224,225,226,226,227,228,228,229,230,231,231,232,233,233,234,235,235,236,237,238,238,239,240,240,241,242,242,243,244,244,245,246,246,247,248,248,249,250,250,251,252,252,253,254,255,0,6,10,13,15,18,20,23,25,27,29,31,33,35,36,38,40,41,43,45,46,48,49,51,52,54,55,57,58,59,61,62,63,65,66,67,69,70,71,72,74,75,76,77,79,80,81,82,83,84,86,87,88,89,90,91,92,93,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,132,133,134,135,136,137,138,139,140,141,142,142,143,144,145,146,147,148,149,149,150,151,152,153,154,155,155,156,157,158,159,160,161,161,162,163,164,165,166,166,167,168,169,170,170,171,172,173,174,175,175,176,177,178,179,179,180,181,182,182,183,184,185,186,186,187,188,189,189,190,191,192,193,193,194,195,196,196,197,198,199,199,200,201,202,202,203,204,205,205,206,207,208,208,209,210,211,211,212,213,213,214,215,216,216,217,218,219,219,220,221,221,222,223,224,224,225,226,226,227,228,228,229,230,231,231,232,233,233,234,235,235,236,237,238,238,239,240,240,241,242,242,243,244,244,245,246,246,247,248,248,249,250,250,251,252,252,253,254,255,0,6,10,13,15,18,20,23,25,27,29,31,33,35,36,38,40,41,43,45,46,48,49,51,52,54,55,57,58,59,61,62,63,65,66,67,69,70,71,72,74,75,76,77,79,80,81,82,83,84,86,87,88,89,90,91,92,93,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,132,133,134,135,136,137,138,139,140,141,142,142,143,144,145,146,147,148,149,149,150,151,152,153,154,155,155,156,157,158,159,160,161,161,162,163,164,165,166,166,167,168,169,170,170,171,172,173,174,175,175,176,177,178,179,179,180,181,182,182,183,184,185,186,186,187,188,189,189,190,191,192,193,193,194,195,196,196,197,198,199,199,200,201,202,202,203,204,205,205,206,207,208,208,209,210,211,211,212,213,213,214,215,216,216,217,218,219,219,220,221,221,222,223,224,224,225,226,226,227,228,228,229,230,231,231,232,233,233,234,235,235,236,237,238,238,239,240,240,241,242,242,243,244,244,245,246,246,247,248,248,249,250,250,251,252,252,253,254,255};
+
+	xdmsc_write(xdmsc, XDEMOSAIC_WIDTH,
+		    xdmsc->formats[XVIP_PAD_SINK].width);
+	xdmsc_write(xdmsc, XDEMOSAIC_HEIGHT,
+		    xdmsc->formats[XVIP_PAD_SINK].height);
+	xdmsc_write(xdmsc, XDEMOSAIC_RGAIN, xdmsc->rgain);
+	xdmsc_write(xdmsc, XDEMOSAIC_BGAIN, xdmsc->bgain);
+	xdmsc_write(xdmsc, XDEMOSAIC_MODE_REG, 1);
+	xdmsc_write(xdmsc, XDEMOSAIC_PAWB, xdmsc->pawb);
+	//xdmsc_write(xdmsc, XDEMOSAIC_INPUT_BAYER_FORMAT, xdmsc->bayer_fmt);
+	xdmsc_set_lut_entries(xdmsc, XDEMOSAIC_GAMMA_LUT, gamma_lut);
+
+	/* Start Demosaic Video IP */
+	xdmsc_write(xdmsc, XDEMOSAIC_AP_CTRL, XDEMOSAIC_STREAM_ON);
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops xdmsc_video_ops = {
+	.s_stream = xdmsc_s_stream,
+};
+
+static int xdmsc_get_format(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_format *fmt)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+	struct v4l2_mbus_framefmt *get_fmt;
+
+	get_fmt = __xdmsc_get_pad_format(xdmsc, sd_state, fmt->pad, fmt->which);
+	if (!get_fmt)
+		return -EINVAL;
+
+	fmt->format = *get_fmt;
+
+	return 0;
+}
+
+static bool
+xdmsc_is_format_bayer(struct xdmsc_dev *xdmsc, u32 code)
+{
+	switch (code) {
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+	case MEDIA_BUS_FMT_SRGGB12_1X12:
+	case MEDIA_BUS_FMT_SRGGB16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_RGGB;
+		break;
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SGRBG12_1X12:
+	case MEDIA_BUS_FMT_SGRBG16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_GRBG;
+		break;
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SGBRG12_1X12:
+	case MEDIA_BUS_FMT_SGBRG16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_GBRG;
+		break;
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+	case MEDIA_BUS_FMT_SBGGR12_1X12:
+	case MEDIA_BUS_FMT_SBGGR16_1X16:
+		xdmsc->bayer_fmt = XDEMOSAIC_BGGR;
+		break;
+	default:
+		dev_dbg(xdmsc->xvip.dev, "Unsupported format for Sink Pad");
+		return false;
+	}
+	return true;
+}
+
+static int xdmsc_set_format(struct v4l2_subdev *subdev,
+			    struct v4l2_subdev_state *sd_state,
+			    struct v4l2_subdev_format *fmt)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+	struct v4l2_mbus_framefmt *__format;
+
+	__format = __xdmsc_get_pad_format(xdmsc, sd_state, fmt->pad, fmt->which);
+	if (!__format)
+		return -EINVAL;
+
+	*__format = fmt->format;
+
+	__format->width = clamp_t(unsigned int, fmt->format.width,
+				  XDEMOSAIC_MIN_WIDTH, xdmsc->max_width);
+	__format->height = clamp_t(unsigned int, fmt->format.height,
+				   XDEMOSAIC_MIN_HEIGHT, xdmsc->max_height);
+
+	if (fmt->pad == XVIP_PAD_SOURCE) {
+		if (__format->code != MEDIA_BUS_FMT_RBG888_1X24 &&
+		    __format->code != MEDIA_BUS_FMT_RBG101010_1X30 &&
+		    __format->code != MEDIA_BUS_FMT_RBG121212_1X36 &&
+		    __format->code != MEDIA_BUS_FMT_RBG161616_1X48) {
+			dev_dbg(xdmsc->xvip.dev,
+				"%s : Unsupported source media bus code format",
+				__func__);
+			__format->code = MEDIA_BUS_FMT_RBG888_1X24;
+		}
+	}
+
+	if (fmt->pad == XVIP_PAD_SINK) {
+		if (!xdmsc_is_format_bayer(xdmsc, __format->code)) {
+			dev_dbg(xdmsc->xvip.dev,
+				"Unsupported Sink Pad Media format, defaulting to RGGB");
+			__format->code = MEDIA_BUS_FMT_SRGGB8_1X8;
+		}
+	}
+
+	fmt->format = *__format;
+	return 0;
+}
+
+static int xdmsc_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct xdmsc_dev *xdmsc = to_xdmsc(subdev);
+	struct v4l2_mbus_framefmt *format;
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SINK);
+	*format = xdmsc->default_formats[XVIP_PAD_SINK];
+
+	format = v4l2_subdev_get_try_format(subdev, fh->state, XVIP_PAD_SOURCE);
+	*format = xdmsc->default_formats[XVIP_PAD_SOURCE];
+	return 0;
+}
+
+static int xdmsc_close(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	return 0;
+}
+
+static const struct v4l2_subdev_internal_ops xdmsc_internal_ops = {
+	.open = xdmsc_open,
+	.close = xdmsc_close,
+};
+
+static const struct v4l2_subdev_pad_ops xdmsc_pad_ops = {
+	.enum_mbus_code = xvip_enum_mbus_code,
+	.enum_frame_size = xvip_enum_frame_size,
+	.get_fmt = xdmsc_get_format,
+	.set_fmt = xdmsc_set_format,
+};
+
+static const struct v4l2_subdev_ops xdmsc_ops = {
+	.video = &xdmsc_video_ops,
+	.pad = &xdmsc_pad_ops,
+};
+
+static const struct media_entity_operations xdmsc_media_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static int xdmsc_parse_of(struct xdmsc_dev *xdmsc)
+{
+	struct device *dev = xdmsc->xvip.dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *ports;
+	struct device_node *port;
+	u32 port_id = 0;
+	int rval;
+
+	rval = of_property_read_u32(node, "xlnx,max-height",
+				    &xdmsc->max_height);
+	if (rval < 0) {
+		dev_err(dev, "missing xlnx,max-height property!");
+		return -EINVAL;
+	} else if (xdmsc->max_height > XDEMOSAIC_MAX_HEIGHT ||
+		 xdmsc->max_height < XDEMOSAIC_MIN_HEIGHT) {
+		dev_err(dev, "Invalid height in dt");
+		return -EINVAL;
+	}
+
+	rval = of_property_read_u32(node, "xlnx,max-width",
+				    &xdmsc->max_width);
+	if (rval < 0) {
+		dev_err(dev, "missing xlnx,max-width property!");
+		return -EINVAL;
+	} else if (xdmsc->max_width > XDEMOSAIC_MAX_WIDTH ||
+		 xdmsc->max_width < XDEMOSAIC_MIN_WIDTH) {
+		dev_err(dev, "Invalid width in dt");
+		return -EINVAL;
+	}
+
+    rval = of_property_read_u32(node, "xlnx,rgain",
+                    &xdmsc->rgain);
+    if (rval < 0) {
+        dev_err(dev, "missing xlnx,rgain!");
+        return -EINVAL;
+    }
+
+    rval = of_property_read_u32(node, "xlnx,bgain",
+                    &xdmsc->bgain);
+    if (rval < 0) {
+        dev_err(dev, "missing xlnx,bgain!");
+        return -EINVAL;
+    }
+
+    rval = of_property_read_u32(node, "xlnx,pawb",
+                    &xdmsc->pawb);
+    if (rval < 0) {
+        dev_err(dev, "missing xlnx,pawb!");
+        return -EINVAL;
+    }
+
+    rval = of_property_read_u32(node, "xlnx,mode-reg",
+                    &xdmsc->mode_reg);
+    if (rval < 0) {
+        dev_err(dev, "missing xlnx,mode-reg!");
+        return -EINVAL;
+    }
+	ports = of_get_child_by_name(node, "ports");
+	if (!ports)
+		ports = node;
+	/* Get the format description for each pad */
+	for_each_child_of_node(ports, port) {
+		if (port->name && (of_node_cmp(port->name, "port") == 0)) {
+			rval = of_property_read_u32(port, "reg", &port_id);
+			if (rval < 0) {
+				dev_err(dev, "No reg in DT");
+				return rval;
+			}
+
+			if (port_id != 0 && port_id != 1) {
+				dev_err(dev, "Invalid reg in DT");
+				return -EINVAL;
+			}
+		}
+	}
+
+	xdmsc->rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(xdmsc->rst_gpio)) {
+		if (PTR_ERR(xdmsc->rst_gpio) != -EPROBE_DEFER)
+			dev_err(dev, "Reset GPIO not setup in DT");
+		return PTR_ERR(xdmsc->rst_gpio);
+	}
+	return 0;
+}
+
+static int xdmsc_probe(struct platform_device *pdev)
+{
+	struct xdmsc_dev *xdmsc;
+	struct v4l2_subdev *subdev;
+	struct v4l2_mbus_framefmt *def_fmt;
+	int rval;
+
+	xdmsc = devm_kzalloc(&pdev->dev, sizeof(*xdmsc), GFP_KERNEL);
+	if (!xdmsc)
+		return -ENOMEM;
+	xdmsc->xvip.dev = &pdev->dev;
+	rval = xdmsc_parse_of(xdmsc);
+	if (rval < 0)
+		return rval;
+	rval = xvip_init_resources(&xdmsc->xvip);
+	if (rval)
+		return -EIO;
+
+	/* Reset Demosaic IP */
+	gpiod_set_value_cansleep(xdmsc->rst_gpio,
+				 XDEMOSAIC_RESET_DEASSERT);
+
+	/* Init V4L2 subdev */
+	subdev = &xdmsc->xvip.subdev;
+	v4l2_subdev_init(subdev, &xdmsc_ops);
+	subdev->dev = &pdev->dev;
+	subdev->internal_ops = &xdmsc_internal_ops;
+	strlcpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev->name));
+	subdev->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Default Formats Initialization */
+	def_fmt = &xdmsc->default_formats[XVIP_PAD_SINK];
+	def_fmt->field = V4L2_FIELD_NONE;
+	def_fmt->colorspace = V4L2_COLORSPACE_SRGB;
+	def_fmt->width = XDEMOSAIC_DEF_WIDTH;
+	def_fmt->height = XDEMOSAIC_DEF_HEIGHT;
+
+	/*
+	 * Sink Pad can be any Bayer format.
+	 * Default Sink Pad format is RGGB.
+	 */
+	def_fmt->code = MEDIA_BUS_FMT_SRGGB10_1X10;
+	xdmsc->formats[XVIP_PAD_SINK] = *def_fmt;
+
+	def_fmt = &xdmsc->default_formats[XVIP_PAD_SOURCE];
+	*def_fmt = xdmsc->default_formats[XVIP_PAD_SINK];
+
+	/* Source Pad has a fixed media bus format of RGB */
+	def_fmt->code = MEDIA_BUS_FMT_RBG888_1X24;
+	xdmsc->formats[XVIP_PAD_SOURCE] = *def_fmt;
+
+	xdmsc->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+	xdmsc->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+	/* Init Media Entity */
+	subdev->entity.ops = &xdmsc_media_ops;
+	rval = media_entity_pads_init(&subdev->entity, 2, xdmsc->pads);
+	if (rval < 0)
+		goto media_error;
+
+	platform_set_drvdata(pdev, xdmsc);
+	rval = v4l2_async_register_subdev(subdev);
+	if (rval < 0) {
+		dev_err(&pdev->dev, "failed to register subdev");
+		goto v4l2_subdev_error;
+	}
+	dev_info(&pdev->dev,
+		 "Xilinx ISP Driver Probe Successful");
+	return 0;
+
+v4l2_subdev_error:
+	media_entity_cleanup(&subdev->entity);
+media_error:
+	xvip_cleanup_resources(&xdmsc->xvip);
+	return rval;
+}
+
+static int xdmsc_remove(struct platform_device *pdev)
+{
+	struct xdmsc_dev *xdmsc = platform_get_drvdata(pdev);
+	struct v4l2_subdev *subdev = &xdmsc->xvip.subdev;
+
+	v4l2_async_unregister_subdev(subdev);
+	media_entity_cleanup(&subdev->entity);
+	xvip_cleanup_resources(&xdmsc->xvip);
+	return 0;
+}
+
+static const struct of_device_id xdmsc_of_id_table[] = {
+	{.compatible = "xlnx,ISPPipeline_accel"},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xdmsc_of_id_table);
+
+static struct platform_driver xdmsc_driver = {
+	.driver = {
+		.name = "xilinx-isppipeline",
+		.of_match_table = xdmsc_of_id_table,
+	},
+	.probe = xdmsc_probe,
+	.remove = xdmsc_remove,
+
+};
+
+module_platform_driver(xdmsc_driver);
+MODULE_DESCRIPTION("Xilinx Demosaic IP Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-isp-module/xilinx-vip.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-isp-module/xilinx-vip.h
@@ -0,0 +1,246 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Xilinx Video IP Core
+ *
+ * Copyright (C) 2013-2015 Ideas on Board
+ * Copyright (C) 2013-2015 Xilinx, Inc.
+ *
+ * Contacts: Hyun Kwon <hyun.kwon@xilinx.com>
+ *           Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ */
+
+#ifndef __XILINX_VIP_H__
+#define __XILINX_VIP_H__
+
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <media/v4l2-subdev.h>
+
+struct clk;
+
+/*
+ * Minimum and maximum width and height common to most video IP cores. IP
+ * cores with different requirements must define their own values.
+ */
+#define XVIP_MIN_WIDTH			32
+#define XVIP_MAX_WIDTH			7680
+#define XVIP_MIN_HEIGHT			32
+#define XVIP_MAX_HEIGHT			7680
+
+/*
+ * Pad IDs. IP cores with with multiple inputs or outputs should define
+ * their own values.
+ */
+#define XVIP_PAD_SINK			0
+#define XVIP_PAD_SOURCE			1
+
+/* Xilinx Video IP Control Registers */
+#define XVIP_CTRL_CONTROL			0x0000
+#define XVIP_CTRL_CONTROL_SW_ENABLE		BIT(0)
+#define XVIP_CTRL_CONTROL_REG_UPDATE		BIT(1)
+#define XVIP_CTRL_CONTROL_BYPASS		BIT(4)
+#define XVIP_CTRL_CONTROL_TEST_PATTERN		BIT(5)
+#define XVIP_CTRL_CONTROL_FRAME_SYNC_RESET	BIT(30)
+#define XVIP_CTRL_CONTROL_SW_RESET		BIT(31)
+#define XVIP_CTRL_STATUS			0x0004
+#define XVIP_CTRL_STATUS_PROC_STARTED		BIT(0)
+#define XVIP_CTRL_STATUS_EOF			BIT(1)
+#define XVIP_CTRL_ERROR				0x0008
+#define XVIP_CTRL_ERROR_SLAVE_EOL_EARLY		BIT(0)
+#define XVIP_CTRL_ERROR_SLAVE_EOL_LATE		BIT(1)
+#define XVIP_CTRL_ERROR_SLAVE_SOF_EARLY		BIT(2)
+#define XVIP_CTRL_ERROR_SLAVE_SOF_LATE		BIT(3)
+#define XVIP_CTRL_IRQ_ENABLE			0x000c
+#define XVIP_CTRL_IRQ_ENABLE_PROC_STARTED	BIT(0)
+#define XVIP_CTRL_IRQ_EOF			BIT(1)
+#define XVIP_CTRL_VERSION			0x0010
+#define XVIP_CTRL_VERSION_MAJOR_MASK		(0xff << 24)
+#define XVIP_CTRL_VERSION_MAJOR_SHIFT		24
+#define XVIP_CTRL_VERSION_MINOR_MASK		(0xff << 16)
+#define XVIP_CTRL_VERSION_MINOR_SHIFT		16
+#define XVIP_CTRL_VERSION_REVISION_MASK		(0xf << 12)
+#define XVIP_CTRL_VERSION_REVISION_SHIFT	12
+#define XVIP_CTRL_VERSION_PATCH_MASK		(0xf << 8)
+#define XVIP_CTRL_VERSION_PATCH_SHIFT		8
+#define XVIP_CTRL_VERSION_INTERNAL_MASK		(0xff << 0)
+#define XVIP_CTRL_VERSION_INTERNAL_SHIFT	0
+
+/* Xilinx Video IP Timing Registers */
+#define XVIP_ACTIVE_SIZE			0x0020
+#define XVIP_ACTIVE_VSIZE_MASK			(0x7ff << 16)
+#define XVIP_ACTIVE_VSIZE_SHIFT			16
+#define XVIP_ACTIVE_HSIZE_MASK			(0x7ff << 0)
+#define XVIP_ACTIVE_HSIZE_SHIFT			0
+#define XVIP_ENCODING				0x0028
+#define XVIP_ENCODING_NBITS_8			(0 << 4)
+#define XVIP_ENCODING_NBITS_10			(1 << 4)
+#define XVIP_ENCODING_NBITS_12			(2 << 4)
+#define XVIP_ENCODING_NBITS_16			(3 << 4)
+#define XVIP_ENCODING_NBITS_MASK		(3 << 4)
+#define XVIP_ENCODING_NBITS_SHIFT		4
+#define XVIP_ENCODING_VIDEO_FORMAT_YUV422	(0 << 0)
+#define XVIP_ENCODING_VIDEO_FORMAT_YUV444	(1 << 0)
+#define XVIP_ENCODING_VIDEO_FORMAT_RGB		(2 << 0)
+#define XVIP_ENCODING_VIDEO_FORMAT_YUV420	(3 << 0)
+#define XVIP_ENCODING_VIDEO_FORMAT_MASK		(3 << 0)
+#define XVIP_ENCODING_VIDEO_FORMAT_SHIFT	0
+
+/**
+ * struct xvip_device - Xilinx Video IP device structure
+ * @subdev: V4L2 subdevice
+ * @dev: (OF) device
+ * @iomem: device I/O register space remapped to kernel virtual memory
+ * @clk: video core clock
+ * @saved_ctrl: saved control register for resume / suspend
+ */
+struct xvip_device {
+	struct v4l2_subdev subdev;
+	struct device *dev;
+	void __iomem *iomem;
+	struct clk *clk;
+	u32 saved_ctrl;
+};
+
+/**
+ * struct xvip_video_format - Xilinx Video IP video format description
+ * @vf_code: AXI4 video format code
+ * @width: AXI4 format width in bits per component
+ * @pattern: CFA pattern for Mono/Sensor formats
+ * @code: media bus format code
+ * @bpl_factor: Bytes per line factor
+ * @bpp: bits per pixel
+ * @fourcc: V4L2 pixel format FCC identifier
+ * @num_planes: number of planes w.r.t. color format
+ * @buffers: number of buffers per format
+ * @hsub: Horizontal sampling factor of Chroma
+ * @vsub: Vertical sampling factor of Chroma
+ */
+struct xvip_video_format {
+	unsigned int vf_code;
+	unsigned int width;
+	const char *pattern;
+	unsigned int code;
+	unsigned int bpl_factor;
+	unsigned int bpp;
+	u32 fourcc;
+	u8 num_planes;
+	u8 buffers;
+	u8 hsub;
+	u8 vsub;
+};
+
+const struct xvip_video_format *xvip_get_format_by_code(unsigned int code);
+const struct xvip_video_format *xvip_get_format_by_fourcc(u32 fourcc);
+const struct xvip_video_format *xvip_of_get_format(struct device_node *node);
+void xvip_bpl_scaling_factor(u32 fourcc, u32 *numerator, u32 *denominator);
+void xvip_width_padding_factor(u32 fourcc, u32 *numerator, u32 *denominator);
+void xvip_set_format_size(struct v4l2_mbus_framefmt *format,
+			  const struct v4l2_subdev_format *fmt);
+int xvip_enum_mbus_code(struct v4l2_subdev *subdev,
+			struct v4l2_subdev_state *sd_state,
+			struct v4l2_subdev_mbus_code_enum *code);
+int xvip_enum_frame_size(struct v4l2_subdev *subdev,
+			 struct v4l2_subdev_state *sd_state,
+			 struct v4l2_subdev_frame_size_enum *fse);
+
+static inline u32 xvip_read(struct xvip_device *xvip, u32 addr)
+{
+	return ioread32(xvip->iomem + addr);
+}
+
+static inline void xvip_write(struct xvip_device *xvip, u32 addr, u32 value)
+{
+	iowrite32(value, xvip->iomem + addr);
+}
+
+static inline void xvip_clr(struct xvip_device *xvip, u32 addr, u32 clr)
+{
+	xvip_write(xvip, addr, xvip_read(xvip, addr) & ~clr);
+}
+
+static inline void xvip_set(struct xvip_device *xvip, u32 addr, u32 set)
+{
+	xvip_write(xvip, addr, xvip_read(xvip, addr) | set);
+}
+
+void xvip_clr_or_set(struct xvip_device *xvip, u32 addr, u32 mask, bool set);
+void xvip_clr_and_set(struct xvip_device *xvip, u32 addr, u32 clr, u32 set);
+
+int xvip_init_resources(struct xvip_device *xvip);
+void xvip_cleanup_resources(struct xvip_device *xvip);
+
+static inline void xvip_reset(struct xvip_device *xvip)
+{
+	xvip_write(xvip, XVIP_CTRL_CONTROL, XVIP_CTRL_CONTROL_SW_RESET);
+}
+
+static inline void xvip_start(struct xvip_device *xvip)
+{
+	xvip_set(xvip, XVIP_CTRL_CONTROL,
+		 XVIP_CTRL_CONTROL_SW_ENABLE | XVIP_CTRL_CONTROL_REG_UPDATE);
+}
+
+static inline void xvip_stop(struct xvip_device *xvip)
+{
+	xvip_clr(xvip, XVIP_CTRL_CONTROL, XVIP_CTRL_CONTROL_SW_ENABLE);
+}
+
+static inline void xvip_resume(struct xvip_device *xvip)
+{
+	xvip_write(xvip, XVIP_CTRL_CONTROL,
+		   xvip->saved_ctrl | XVIP_CTRL_CONTROL_SW_ENABLE);
+}
+
+static inline void xvip_suspend(struct xvip_device *xvip)
+{
+	xvip->saved_ctrl = xvip_read(xvip, XVIP_CTRL_CONTROL);
+	xvip_write(xvip, XVIP_CTRL_CONTROL,
+		   xvip->saved_ctrl & ~XVIP_CTRL_CONTROL_SW_ENABLE);
+}
+
+static inline void xvip_set_frame_size(struct xvip_device *xvip,
+				       const struct v4l2_mbus_framefmt *format)
+{
+	xvip_write(xvip, XVIP_ACTIVE_SIZE,
+		   (format->height << XVIP_ACTIVE_VSIZE_SHIFT) |
+		   (format->width << XVIP_ACTIVE_HSIZE_SHIFT));
+}
+
+static inline void xvip_get_frame_size(struct xvip_device *xvip,
+				       struct v4l2_mbus_framefmt *format)
+{
+	u32 reg;
+
+	reg = xvip_read(xvip, XVIP_ACTIVE_SIZE);
+	format->width = (reg & XVIP_ACTIVE_HSIZE_MASK) >>
+			XVIP_ACTIVE_HSIZE_SHIFT;
+	format->height = (reg & XVIP_ACTIVE_VSIZE_MASK) >>
+			 XVIP_ACTIVE_VSIZE_SHIFT;
+}
+
+static inline void xvip_enable_reg_update(struct xvip_device *xvip)
+{
+	xvip_set(xvip, XVIP_CTRL_CONTROL, XVIP_CTRL_CONTROL_REG_UPDATE);
+}
+
+static inline void xvip_disable_reg_update(struct xvip_device *xvip)
+{
+	xvip_clr(xvip, XVIP_CTRL_CONTROL, XVIP_CTRL_CONTROL_REG_UPDATE);
+}
+
+static inline void xvip_print_version(struct xvip_device *xvip)
+{
+	u32 version;
+
+	version = xvip_read(xvip, XVIP_CTRL_VERSION);
+
+	dev_info(xvip->dev, "device found, version %u.%02x%x\n",
+		 ((version & XVIP_CTRL_VERSION_MAJOR_MASK) >>
+		  XVIP_CTRL_VERSION_MAJOR_SHIFT),
+		 ((version & XVIP_CTRL_VERSION_MINOR_MASK) >>
+		  XVIP_CTRL_VERSION_MINOR_SHIFT),
+		 ((version & XVIP_CTRL_VERSION_REVISION_MASK) >>
+		  XVIP_CTRL_VERSION_REVISION_SHIFT));
+}
+
+#endif /* __XILINX_VIP_H__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-10gige-module/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-10gige-module/Kconfig
@@ -0,0 +1,4 @@
+config NET_VENDOR_S2I
+	tristate "Sensor to Image Ethernet MAC support"
+	help
+	  Say Y here if you want to use the Sensor to Image Ethernet MAC.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-10gige-module/LICENSE.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-10gige-module/LICENSE.md
@@ -0,0 +1,342 @@
+		    GNU GENERAL PUBLIC LICENSE
+		       Version 2, June 1991
+
+ Copyright (C) 1989, 1991 Free Software Foundation, Inc.
+                       51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+			    Preamble
+
+  The licenses for most software are designed to take away your
+freedom to share and change it.  By contrast, the GNU General Public
+License is intended to guarantee your freedom to share and change free
+software--to make sure the software is free for all its users.  This
+General Public License applies to most of the Free Software
+Foundation's software and to any other program whose authors commit to
+using it.  (Some other Free Software Foundation software is covered by
+the GNU Library General Public License instead.)  You can apply it to
+your programs, too.
+
+  When we speak of free software, we are referring to freedom, not
+price.  Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+this service if you wish), that you receive source code or can get it
+if you want it, that you can change the software or use pieces of it
+in new free programs; and that you know you can do these things.
+
+  To protect your rights, we need to make restrictions that forbid
+anyone to deny you these rights or to ask you to surrender the rights.
+These restrictions translate to certain responsibilities for you if you
+distribute copies of the software, or if you modify it.
+
+  For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must give the recipients all the rights that
+you have.  You must make sure that they, too, receive or can get the
+source code.  And you must show them these terms so they know their
+rights.
+
+  We protect your rights with two steps: (1) copyright the software, and
+(2) offer you this license which gives you legal permission to copy,
+distribute and/or modify the software.
+
+  Also, for each author's protection and ours, we want to make certain
+that everyone understands that there is no warranty for this free
+software.  If the software is modified by someone else and passed on, we
+want its recipients to know that what they have is not the original, so
+that any problems introduced by others will not reflect on the original
+authors' reputations.
+
+  Finally, any free program is threatened constantly by software
+patents.  We wish to avoid the danger that redistributors of a free
+program will individually obtain patent licenses, in effect making the
+program proprietary.  To prevent this, we have made it clear that any
+patent must be licensed for everyone's free use or not licensed at all.
+
+  The precise terms and conditions for copying, distribution and
+modification follow.
+
+		    GNU GENERAL PUBLIC LICENSE
+   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
+
+  0. This License applies to any program or other work which contains
+a notice placed by the copyright holder saying it may be distributed
+under the terms of this General Public License.  The "Program", below,
+refers to any such program or work, and a "work based on the Program"
+means either the Program or any derivative work under copyright law:
+that is to say, a work containing the Program or a portion of it,
+either verbatim or with modifications and/or translated into another
+language.  (Hereinafter, translation is included without limitation in
+the term "modification".)  Each licensee is addressed as "you".
+
+Activities other than copying, distribution and modification are not
+covered by this License; they are outside its scope.  The act of
+running the Program is not restricted, and the output from the Program
+is covered only if its contents constitute a work based on the
+Program (independent of having been made by running the Program).
+Whether that is true depends on what the Program does.
+
+  1. You may copy and distribute verbatim copies of the Program's
+source code as you receive it, in any medium, provided that you
+conspicuously and appropriately publish on each copy an appropriate
+copyright notice and disclaimer of warranty; keep intact all the
+notices that refer to this License and to the absence of any warranty;
+and give any other recipients of the Program a copy of this License
+along with the Program.
+
+You may charge a fee for the physical act of transferring a copy, and
+you may at your option offer warranty protection in exchange for a fee.
+
+  2. You may modify your copy or copies of the Program or any portion
+of it, thus forming a work based on the Program, and copy and
+distribute such modifications or work under the terms of Section 1
+above, provided that you also meet all of these conditions:
+
+    a) You must cause the modified files to carry prominent notices
+    stating that you changed the files and the date of any change.
+
+    b) You must cause any work that you distribute or publish, that in
+    whole or in part contains or is derived from the Program or any
+    part thereof, to be licensed as a whole at no charge to all third
+    parties under the terms of this License.
+
+    c) If the modified program normally reads commands interactively
+    when run, you must cause it, when started running for such
+    interactive use in the most ordinary way, to print or display an
+    announcement including an appropriate copyright notice and a
+    notice that there is no warranty (or else, saying that you provide
+    a warranty) and that users may redistribute the program under
+    these conditions, and telling the user how to view a copy of this
+    License.  (Exception: if the Program itself is interactive but
+    does not normally print such an announcement, your work based on
+    the Program is not required to print an announcement.)
+
+These requirements apply to the modified work as a whole.  If
+identifiable sections of that work are not derived from the Program,
+and can be reasonably considered independent and separate works in
+themselves, then this License, and its terms, do not apply to those
+sections when you distribute them as separate works.  But when you
+distribute the same sections as part of a whole which is a work based
+on the Program, the distribution of the whole must be on the terms of
+this License, whose permissions for other licensees extend to the
+entire whole, and thus to each and every part regardless of who wrote it.
+
+Thus, it is not the intent of this section to claim rights or contest
+your rights to work written entirely by you; rather, the intent is to
+exercise the right to control the distribution of derivative or
+collective works based on the Program.
+
+In addition, mere aggregation of another work not based on the Program
+with the Program (or with a work based on the Program) on a volume of
+a storage or distribution medium does not bring the other work under
+the scope of this License.
+
+  3. You may copy and distribute the Program (or a work based on it,
+under Section 2) in object code or executable form under the terms of
+Sections 1 and 2 above provided that you also do one of the following:
+
+    a) Accompany it with the complete corresponding machine-readable
+    source code, which must be distributed under the terms of Sections
+    1 and 2 above on a medium customarily used for software interchange; or,
+
+    b) Accompany it with a written offer, valid for at least three
+    years, to give any third party, for a charge no more than your
+    cost of physically performing source distribution, a complete
+    machine-readable copy of the corresponding source code, to be
+    distributed under the terms of Sections 1 and 2 above on a medium
+    customarily used for software interchange; or,
+
+    c) Accompany it with the information you received as to the offer
+    to distribute corresponding source code.  (This alternative is
+    allowed only for noncommercial distribution and only if you
+    received the program in object code or executable form with such
+    an offer, in accord with Subsection b above.)
+
+The source code for a work means the preferred form of the work for
+making modifications to it.  For an executable work, complete source
+code means all the source code for all modules it contains, plus any
+associated interface definition files, plus the scripts used to
+control compilation and installation of the executable.  However, as a
+special exception, the source code distributed need not include
+anything that is normally distributed (in either source or binary
+form) with the major components (compiler, kernel, and so on) of the
+operating system on which the executable runs, unless that component
+itself accompanies the executable.
+
+If distribution of executable or object code is made by offering
+access to copy from a designated place, then offering equivalent
+access to copy the source code from the same place counts as
+distribution of the source code, even though third parties are not
+compelled to copy the source along with the object code.
+
+  4. You may not copy, modify, sublicense, or distribute the Program
+except as expressly provided under this License.  Any attempt
+otherwise to copy, modify, sublicense or distribute the Program is
+void, and will automatically terminate your rights under this License.
+However, parties who have received copies, or rights, from you under
+this License will not have their licenses terminated so long as such
+parties remain in full compliance.
+
+  5. You are not required to accept this License, since you have not
+signed it.  However, nothing else grants you permission to modify or
+distribute the Program or its derivative works.  These actions are
+prohibited by law if you do not accept this License.  Therefore, by
+modifying or distributing the Program (or any work based on the
+Program), you indicate your acceptance of this License to do so, and
+all its terms and conditions for copying, distributing or modifying
+the Program or works based on it.
+
+  6. Each time you redistribute the Program (or any work based on the
+Program), the recipient automatically receives a license from the
+original licensor to copy, distribute or modify the Program subject to
+these terms and conditions.  You may not impose any further
+restrictions on the recipients' exercise of the rights granted herein.
+You are not responsible for enforcing compliance by third parties to
+this License.
+
+  7. If, as a consequence of a court judgment or allegation of patent
+infringement or for any other reason (not limited to patent issues),
+conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License.  If you cannot
+distribute so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you
+may not distribute the Program at all.  For example, if a patent
+license would not permit royalty-free redistribution of the Program by
+all those who receive copies directly or indirectly through you, then
+the only way you could satisfy both it and this License would be to
+refrain entirely from distribution of the Program.
+
+If any portion of this section is held invalid or unenforceable under
+any particular circumstance, the balance of the section is intended to
+apply and the section as a whole is intended to apply in other
+circumstances.
+
+It is not the purpose of this section to induce you to infringe any
+patents or other property right claims or to contest validity of any
+such claims; this section has the sole purpose of protecting the
+integrity of the free software distribution system, which is
+implemented by public license practices.  Many people have made
+generous contributions to the wide range of software distributed
+through that system in reliance on consistent application of that
+system; it is up to the author/donor to decide if he or she is willing
+to distribute software through any other system and a licensee cannot
+impose that choice.
+
+This section is intended to make thoroughly clear what is believed to
+be a consequence of the rest of this License.
+
+  8. If the distribution and/or use of the Program is restricted in
+certain countries either by patents or by copyrighted interfaces, the
+original copyright holder who places the Program under this License
+may add an explicit geographical distribution limitation excluding
+those countries, so that distribution is permitted only in or among
+countries not thus excluded.  In such case, this License incorporates
+the limitation as if written in the body of this License.
+
+  9. The Free Software Foundation may publish revised and/or new versions
+of the General Public License from time to time.  Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+Each version is given a distinguishing version number.  If the Program
+specifies a version number of this License which applies to it and "any
+later version", you have the option of following the terms and conditions
+either of that version or of any later version published by the Free
+Software Foundation.  If the Program does not specify a version number of
+this License, you may choose any version ever published by the Free Software
+Foundation.
+
+  10. If you wish to incorporate parts of the Program into other free
+programs whose distribution conditions are different, write to the author
+to ask for permission.  For software which is copyrighted by the Free
+Software Foundation, write to the Free Software Foundation; we sometimes
+make exceptions for this.  Our decision will be guided by the two goals
+of preserving the free status of all derivatives of our free software and
+of promoting the sharing and reuse of software generally.
+
+			    NO WARRANTY
+
+  11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
+FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.  EXCEPT WHEN
+OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
+PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
+OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRE RISK AS
+TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.  SHOULD THE
+PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
+REPAIR OR CORRECTION.
+
+  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
+REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
+INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
+OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
+TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
+YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
+PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGES.
+
+		     END OF TERMS AND CONDITIONS
+
+	    How to Apply These Terms to Your New Programs
+
+  If you develop a new program, and you want it to be of the greatest
+possible use to the public, the best way to achieve this is to make it
+free software which everyone can redistribute and change under these terms.
+
+  To do so, attach the following notices to the program.  It is safest
+to attach them to the start of each source file to most effectively
+convey the exclusion of warranty; and each file should have at least
+the "copyright" line and a pointer to where the full notice is found.
+
+    <one line to give the program's name and a brief idea of what it does.>
+    Copyright (C) <year>  <name of author>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+Also add information on how to contact you by electronic and paper mail.
+
+If the program is interactive, make it output a short notice like this
+when it starts in an interactive mode:
+
+    Gnomovision version 69, Copyright (C) year name of author
+    Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
+    This is free software, and you are welcome to redistribute it
+    under certain conditions; type `show c' for details.
+
+The hypothetical commands `show w' and `show c' should show the appropriate
+parts of the General Public License.  Of course, the commands you use may
+be called something other than `show w' and `show c'; they could even be
+mouse-clicks or menu items--whatever suits your program.
+
+You should also get your employer (if you work as a programmer) or your
+school, if any, to sign a "copyright disclaimer" for the program, if
+necessary.  Here is a sample; alter the names:
+
+  Yoyodyne, Inc., hereby disclaims all copyright interest in the program
+  `Gnomovision' (which makes passes at compilers) written by James Hacker.
+
+  <signature of Ty Coon>, 1 April 1989
+  Ty Coon, President of Vice
+
+This General Public License does not permit incorporating your program into
+proprietary programs.  If your program is a subroutine library, you may
+consider it more useful to permit linking proprietary applications with the
+library.  If this is what you want to do, use the GNU Library General
+Public License instead of this License.
+
+Copyright (C) 2022 Sensor to Image GmbH.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-10gige-module/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-10gige-module/Makefile
@@ -0,0 +1,22 @@
+s2imac-objs := s2imac_m.o
+obj-m := s2imac.o
+
+SRC := $(shell pwd)
+
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/include/linux
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/generated/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/generated/uapi/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/uapi/
+
+all:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules
+
+modules_install:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules_install
+
+clean:
+	rm -f *.o *~ core .depend .*.cmd *.ko *.mod.c
+	rm -f Module.markers Module.symvers modules.order
+	rm -f */modules.order */modules.builtin
+	rm -rf .tmp_versions Modules.symvers
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-10gige-module/README.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-10gige-module/README.md
@@ -0,0 +1,2 @@
+# mv-camera-10gige-module
+This repository contains the driver source code for KR260 10gige module, which we got it from IP partner Euresys.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-10gige-module/s2imac.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-10gige-module/s2imac.h
@@ -0,0 +1,286 @@
+/******************************************************************************/
+/*  Linux driver header for the s2imac device.                                */
+/*  Copyright (c) 2022. Sensor to Image GmbH.						          */
+/*                                                                            */
+/*  This program is free software; you can redistribute it and/or modify      */
+/*  it under the terms of the GNU General Public License version 2 as         */
+/*  published by the Free Software Foundation.								  */
+/*----------------------------------------------------------------------------*/
+/*    File :  s2imac.h                                                        */
+/*    Date :  2021-09-29                                                      */
+/*     Rev :  1.4                                                             */
+/*  Author :  RW                                                              */
+/*----------------------------------------------------------------------------*/
+/*  GigE Vision control protocol                                              */
+/*----------------------------------------------------------------------------*/
+/*  0.1  |  2018-03-15  |  RW  |  Initial release                             */
+/*  0.2  |  2018-05-29  |  RW  |  Version to 1.1.4                            */
+/*  0.3  |  2018-07-05  |  RW  |  Version to 1.1.5                            */
+/*  0.4  |  2018-09-05  |  RW  |  Add TIMEOUT_READ_WRITE_PHY define           */
+/*       |              |      |  Version to 1.1.6                            */
+/*  0.5  |  2018-10-18  |  RW  |  Version to 1.1.7                            */
+/*  0.6  |  2018-11-05  |  RW  |  Added MDIO_CLOCK and MDIO_CLOCK_DIV defines */
+/*       |              |      |  Version to 1.1.8                            */
+/*  0.7  |  2019-01-04  |  RW  |  Add rx/tx buffer to net_local structure     */
+/*       |              |      |  Add zynqmp arch                             */
+/*       |              |      |  Version to 1.1.9                            */
+/*  0.8  |  2019-08-08  |  RW  |  Version to 1.2.0                            */
+/*  0.9  |  2019-08-23  |  RW  |  Version to 1.2.1                            */
+/*  0.10 |  2019-09-02  |  RW  |  Version to 1.2.2                            */
+/*  1.0  |  2019-11-18  |  RW  |  Version to 1.3.0                            */
+/*  1.1  |  2020-12-15  |  RW  |  Set little-endian mode for linux            */ 
+/*       |              |      |  Added config-interface to device tree       */ 
+/*       |              |      |  Version to 1.3.1                            */
+/*  1.2  |  2021-01-29  |  RW  |  Version to 1.3.2                            */
+/*  1.3  |  2021-08-31  |  RW  |  Added Xilinx 10/25-Gigabit Ethernet         */
+/*       |              |      |  PCS/PMA IP core                             */ 
+/*       |              |      |  Version to 1.4.0                            */
+/*  1.4  |  2021-09-29  |  RW  |  Version to 1.4.1                            */
+/******************************************************************************/
+#ifndef _S2IMAC_H_
+#define _S2IMAC_H_
+
+#include <linux/module.h>
+#include <linux/uaccess.h>
+#include <linux/init.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/io.h>
+
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 7, 0)
+#define HAVE_TRANS_START_HELPER
+#endif
+
+#define DRIVER_NAME "s2imac"
+#define DRIVER_VERS "1.4.1"
+
+#define TIMEOUT_READ_WRITE_PHY  2000
+ 
+//#define NBASE_T_MARVELL 1
+ 
+//#define CONFIG_S2IMAC_POLLING 1
+
+/* MDIO register basis */
+#define MDIO_BASE   (lp->base_addr[S2IMAC_GIGEMAP] + 0x1000)
+#define MDIO_BASE1  (lp->base_addr[S2IMAC_GIGEMAP] + 0x3000)
+
+/* Tx/Rx buffer basis */
+#define TXBUF         (lp->base_addr[S2IMAC_GIGEMAP] + 0x4000)
+#define RXBUF         (lp->base_addr[S2IMAC_GIGEMAP] + 0x8000)
+
+/* MAC registers definition */
+#define SPEED   (lp->base_addr[S2IMAC_GIGEMAP] + (0x100 << 2))
+#define RCW1    (lp->base_addr[S2IMAC_GIGEMAP] + (0x240 << 2))
+#define TC      (lp->base_addr[S2IMAC_GIGEMAP] + (0x280 << 2))
+#define EMMC    (lp->base_addr[S2IMAC_GIGEMAP] + (0x300 << 2))
+#define MC      (lp->base_addr[S2IMAC_GIGEMAP] + (0x340 << 2))
+#define UAW0    (lp->base_addr[S2IMAC_GIGEMAP] + (0x380 << 2))
+#define UAW1    (lp->base_addr[S2IMAC_GIGEMAP] + (0x384 << 2))
+#define AFM     (lp->base_addr[S2IMAC_GIGEMAP] + (0x390 << 2))
+
+
+
+
+#define MDIO_RXTX_JUMBO   (1 << 30)
+#define MDIO_RXTX_ENABLE  (1 << 28)
+#define MDIO_RXTX_HALFDUPLEX  (1 << 26)
+
+#define MDIO_EMMC_10BASET (0)
+#define MDIO_EMMC_100BASET  (1 << 30)
+#define MDIO_EMMC_1000BASET (1 << 31)
+
+#define MDIO_ENABLE_MASK  (1 << 6)
+#define MDIO_CLOCK_DIV_MASK ((1 << 6) - 1)
+
+#define MDIO_ENABLE_MASK1  (1 << 5)
+#define MDIO_CLOCK_DIV_MASK1 ((1 << 5) - 1)
+
+#define MDIO_CLOCK  (2500000) /* 2.5 MHz */
+#define MDIO_CLOCK_DIV  (MDIO_CLOCK_DIV_MASK & \
+      ((lp->coreclk / (2 * MDIO_CLOCK)) - 1))
+
+#define MDIO_CLOCK_DIV1  (MDIO_CLOCK_DIV_MASK1 & \
+      ((lp->coreclk / (2 * MDIO_CLOCK)) - 1))
+      
+/* direct registers definition */
+#define GCSR        (lp->base_addr[S2IMAC_GIGEMAP] + 0xC000)
+#define CLK_FREQ    (lp->base_addr[S2IMAC_GIGEMAP] + 0xC008)
+#define TOCNT_DIV   (lp->base_addr[S2IMAC_GIGEMAP] + 0xC014)
+#define MDIO_ACC    (lp->base_addr[S2IMAC_GIGEMAP] + 0xC028)
+#define ETHSIZE     (lp->base_addr[S2IMAC_GIGEMAP] + 0xC02C)
+#define MAC_HIGH    (lp->base_addr[S2IMAC_GIGEMAP] + 0xC030)
+#define MAC_LOW     (lp->base_addr[S2IMAC_GIGEMAP] + 0xC034)
+#define TX_LEN      (lp->base_addr[S2IMAC_GIGEMAP] + 0xC048)
+#define RX_LEN      (lp->base_addr[S2IMAC_GIGEMAP] + 0xC04C)
+#define MAC_RX_HIGH (lp->base_addr[S2IMAC_GIGEMAP] + 0xC090)
+#define MAC_RX_LOW  (lp->base_addr[S2IMAC_GIGEMAP] + 0xC094)
+
+#ifndef CONFIG_S2IMAC_POLLING
+#define INT_MASK    (lp->base_addr[S2IMAC_GIGEMAP] + 0xC0AC)
+#define INT_REQ     (lp->base_addr[S2IMAC_GIGEMAP] + 0xC0B0)
+#endif
+
+#define ID_REG      (lp->base_addr[S2IMAC_GIGEMAP] + 0xC0B4)
+
+
+#define GCSR_CONNECTED      0x00000001
+#define GCSR_IP_OK          0x00000002
+#define GCSR_LITTLE_ENDIAN  0x01000000
+
+#define GCSR_RST_PHY    (1 << 2)
+
+#define MDIO_ACC_ENA_NBLOCK (1 << 31)
+#define MDIO_ACC_NBLOCK   (1 << 16)
+#define MDIO_ACC_MIIRDY   (1 << 17)
+
+#ifndef CONFIG_S2IMAC_POLLING
+#define INT_ENABLE_RX   (1)
+#define INT_ENABLE_TX   (1 << 1)
+#define INT_ENABLE_IRQS   (1 << 31)
+#endif
+
+/* max MTU size of an ... */
+#define XTE_MTU     1500  /* Ethernet frame */
+#define XTE_JUMBO_MTU   8982  /* jumbo Ethernet frame, not supported by the GigE core */
+#define XTE_HDR_SIZE    14  /* Ethernet header */
+#define XTE_HDR_VLAN_SIZE 18  /* Ethernet header with VLAN */
+#define XTE_TRL_SIZE    4 /* Ethernet trailer (FCS) */
+#define XTE_MAX_FRAME_SIZE  (XTE_MTU + XTE_HDR_SIZE + XTE_TRL_SIZE)
+#define XTE_MAX_VLAN_FRAME_SIZE (XTE_MTU + XTE_HDR_VLAN_SIZE + XTE_TRL_SIZE)
+#define XTE_MAX_JUMBO_FRAME_SIZE (XTE_JUMBO_MTU + XTE_HDR_SIZE + XTE_TRL_SIZE)
+
+/* Tx timeout is 60 seconds. */
+#define TX_TIMEOUT    (60*HZ)
+
+/* BUFFER_ALIGN(adr) calculates the number of bytes to the next alignment. */
+#define ALIGNMENT   4
+#define BUFFER_ALIGN(adr) ((ALIGNMENT - ((ulong)adr)) % ALIGNMENT)
+
+/* Read/Write access to the registers */
+#ifndef in_be32
+#if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP)
+#define in_be32(offset)   __raw_readl(offset)
+#define out_be32(offset, val) __raw_writel(val, offset)
+#endif
+#endif
+
+#define DWORD_SWAP(x) ((((x) << 24) & 0xff000000L) | \
+       (((x) <<  8) & 0x00ff0000L) | \
+       (((x) >>  8) & 0x0000ff00L) | \
+       (((x) >> 24) & 0x000000ffL) )
+
+# define WORD_SWAP(x) ((((x) << 8) & 0xff00) | (((x) >> 8) & 0x00ff)) 
+
+// Types of the Ethernet PHYs
+#define PHY_BROADCOM    0x00
+#define PHY_MARVELL     0x01
+#define PHY_NATIONAL    0x02
+#define PHY_MICREL      0x03
+#define PHY_10G_AEL2005 0x04
+#define PHY_10G_TN80XX  0x05
+#define PHY_10G_PCS_PMA 0x06
+#define PHY_1G_PCS_PMA  0x07
+#define PHY_TI          0x08
+#define PHY_NBASET_MRVL 0x09
+#define PHY_NBASET_AQR  0x0A
+#define PHY_SWITCH_MRVL 0x0B
+#define PHY_25G_PCS_PMA 0x0C
+#define PHY_NONE        0xFF
+
+// NBASE-T MAC TX link speed throttling constants
+#define NBASET_SPD_10G  0
+#define NBASET_SPD_5G   1
+#define NBASET_SPD_2500 3
+#define NBASET_SPD_1000 9
+
+// Host interface mode
+typedef enum phy_if_mode {DEFAULT, XAUI, RXAUI, USXGMII} phy_if_mode;
+
+/**send_data
+ * struct net_local - Our private per device data
+ * @ndev:   instance of the network device
+ * @base_addr[]:  base address of the s2imac device
+ * @coreclk:    ip core clock frequency in Hz
+ * @regmem_end:   physical end of GigEV register bank
+ * @regmem_start: physical start of GigEV register bank
+ * @reset_lock:   lock used for synchronization
+ * @deferred_skb: holds an skb (for transmission at a later time) when the
+ *      Tx buffer is not free
+ * @phy_dev:    pointer to the PHY device
+ * @phy_node:   pointer to the PHY device node
+ * @last_link:    last link status
+ * @cur_speed:    current speed
+ */
+struct net_local {
+
+  struct net_device *ndev;
+
+#define S2IMAC_GIGEMAP        0
+#define S2IMAC_VIDEOMAP       1
+#define S2IMAC_FRAMEBUFFERMAP 2
+#define MAX_S2IMAC_MAPS       3
+  
+  void __iomem *base_addr[MAX_S2IMAC_MAPS];
+  unsigned int coreclk;
+
+  unsigned long video_end;
+  unsigned long video_start;
+
+  unsigned long framebuffer_end;
+  unsigned long framebuffer_start;
+  
+
+  spinlock_t reset_lock;
+  struct sk_buff *deferred_skb;
+
+  /* FIXME: use mdio bus: struct phy_device *phy_dev; */
+  /* FIXME: use mdio bus: struct device_node *phy_node; */
+  u32 phy_addr;   /* FIXME: really global, use mdio bus */
+
+  int last_link;
+  int cur_speed;
+
+  u8 phy_type; 
+  u8 init_phy; 
+
+  u32 *gige_txbuf;
+  u32 *gige_rxbuf;
+
+#ifdef CONFIG_S2IMAC_POLLING
+  struct timer_list irq_timer;  /* ISR polling timer */
+#endif
+
+  struct timer_list phy_timer;  /* PHY monitoring timer */
+  
+  phy_if_mode config_interface;
+
+  void __iomem *phy_base_addr;
+
+  unsigned long phy_base_end;
+  unsigned long phy_base_start;
+};
+
+/* some useful structs and typedefs for s2imac.c */
+typedef struct {
+  __u32 address;
+  __u32 data;
+} s2igen_content_t;
+
+/* some useful defines for s2imac.c */
+#define SIOS2IGENRD   SIOCDEVPRIVATE+0  /* generic read */
+#define SIOS2IGENWR   SIOCDEVPRIVATE+1  /* generic write */
+
+/* old defines */
+#define SIOS2IREGRD   SIOCDEVPRIVATE+2  /* register read */
+#define SIOS2IREGWR   SIOCDEVPRIVATE+3  /* register write */
+
+/* new defines */
+#define SIOS2IVIDEORD   SIOCDEVPRIVATE+2    /* video read */
+#define SIOS2IVIDEOWR   SIOCDEVPRIVATE+3    /* video write */
+#define SIOS2IFBUFRD    SIOCDEVPRIVATE+4    /* framebuffer read */
+#define SIOS2IFBUFWR    SIOCDEVPRIVATE+5    /* framebuffer write */
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-10gige-module/s2imac_m.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-10gige-module/s2imac_m.c
@@ -0,0 +1,2214 @@
+/******************************************************************************/
+/*  Linux driver for the s2imac device.                                       */
+/*  Copyright (c) 2022. Sensor to Image GmbH.                                 */
+/*                                                                            */
+/*  This program is free software; you can redistribute it and/or modify      */
+/*  it under the terms of the GNU General Public License version 2 as         */
+/*  published by the Free Software Foundation.                                */
+/*----------------------------------------------------------------------------*/
+/*    File :  s2imac_m.c                                                      */
+/*    Date :  2021-09-29                                                      */
+/*     Rev :  1.4                                                             */
+/*  Author :  RW                                                              */
+/*----------------------------------------------------------------------------*/
+/*  GigE Vision control protocol                                              */
+/*----------------------------------------------------------------------------*/
+/*  0.1  |  2010-10     |  RW  |  Initial release                             */
+/*  0.2  |  2011-01     |  RW  |  Code improvements and coding style          */
+/*       |              |      |  corrections                                 */  
+/*  0.3  |  2011-02     |  RW  |  Change over to an interrupt driven network  */
+/*       |              |      |  driver                                      */
+/*  0.4  |  2013-07     |  RW  |  Added broadcom BCM54610 phy support         */
+/*  0.5  |  2013-12     |  RW  |  Remove swab bytes in send and receive data  */
+/*       |              |      |  (is made in fpga)                           */
+/*  0.6  |  2016-04     |  RW  |  Support zynq                                */
+/*  0.7  |  2016-11-23  |  RW  |  Bug fix:when data with odd length is sent   */
+/*       |              |      |  Version to 1.1.0                            */
+/*  0.8  |  2016-12-06  |  RW  |  Add support for Marwell 88e1512 PHY         */
+/*       |              |      |  Problem (crash) fixed when driver is        */
+/*       |              |      |  unloaded as a module                        */
+/*       |              |      |  Check for maximum MTU size of 1500 bytes    */
+/*       |              |      |  in s2imac_change_mtu function               */
+/*       |              |      |  Display driver version and copyright when   */
+/*       |              |      |  started                                     */
+/*       |              |      |  Version to 1.1.1                            */
+/*  0.8  |  2017-05-16  |  RW  |  Description was changed                     */
+/*  0.9  |  2017-12-04  |  RW  |  Fix compile error for linux 4.7 and greater */
+/*       |              |      |  Version to 1.1.2                            */
+/*  0.10 |  2018-03-15  |  RW  |  Add Marvel NBASE T Phy                      */
+/*       |              |      |  Version to 1.1.3                            */
+/*  0.11 |  2018-05-29  |  RW  |  Wait after close the network device         */
+/*  0.12 |  2018-07-05  |  RW  |  Remove wait after close the network device  */
+/*       |              |      |  Clear rx buffer when close the device       */
+/*  0.13 |  2018-09-05  |  RW  |  Add timeout in read/write ethernet PHY regs */
+/*       |              |      |  remove not used code in ethtool_get_settings*/
+/*  0.14 |  2018-10-29  |  RW  |  Clear XGigE interrupts and clear RX_LEN     */
+/*       |              |      |  register in s2imac_enable_interrupts        */
+/*       |              |      |  Clear always the rx interrupt in            */
+/*       |              |      |  s2imac_rx_handler function                  */
+/*  0.15 |  2018-11-05  |  RW  |  Set current parameter to phy_setup function */
+/*       |              |      |  Fixed the build warnings                    */
+/*       |              |      |  Moved MDIO_CLOCK and MDIO_CLOCK_DIV defines */
+/*       |              |      |  to s2imac.h header file                     */
+/*       |              |      |  Removed unused code                         */
+/*  0.16 |  2019-01-04  |  RW  |  Add rx/tx buffer to net_local structure     */
+/*       |              |      |  Set the base address pointers to 0 if unmap */
+/*       |              |      |  Get the available register name from the    */
+/*       |              |      |  device tree (core, video, framebuffer)      */
+/*       |              |      |  e.q. reg-names = "core", "framebuffer";     */
+/*       |              |      |  Change the error handling in s2imac_of_probe*/
+/*       |              |      |  if no phy found chancel s2imac_of_probe     */
+/*  0.17 |  2019-08-08  |  RW  |  Don't set the gcsr connected bit in         */
+/*       |              |      |  set_mac_speed function                      */ 
+/*  0.18 |  2019-08-23  |  RW  |  If link is up than set gcsr connected bit   */
+/*       |              |      |  in open function                            */ 
+/*       |              |      |  Fixed bug to get iospace for video and      */ 
+/*       |              |      |  framebuffer                                 */ 
+/*  0.19 |  2019-09-02  |  RW  |  Added s2imac_set_rx_mode function to enable */ 
+/*       |              |      |  or disable multicast mode                   */ 
+/*       |              |      |  Change error outputs for register mapping   */ 
+/*  1.0  |  2019-11-18  |  RW  |  Added NBASE-T Marvell PH support            */ 
+/*       |              |      |  Rename file to s2imac_m.c                   */ 
+/*  1.1  |  2020-12-15  |  RW  |  Set little-endian mode for linux            */ 
+/*       |              |      |  Added config-interface to device tree       */ 
+/*  1.2  |  2021-01-29  |  RW  |  Add new timer functions was changed by      */
+/*       |              |      |  kernel 4.15.0                               */
+/*       |              |      |  Struct ethtool_ops was changed by kernel    */
+/*       |              |      |  add new get and set link functions          */ 
+/*  1.3  |  2021-08-31  |  RW  |  Added Xilinx 10/25-Gigabit Ethernet         */ 
+/*       |              |      |  PCS/PMA IP core                             */ 
+/*  1.4  |  2021-09-29  |  RW  |  struct ethtool_link_ksettings was changed by*/
+/*       |              |      |  kernel 4.9.212                              */
+/******************************************************************************/
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/uaccess.h>
+#include <linux/init.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+
+#include "s2imac.h"
+
+#ifdef NBASE_T_MARVELL
+/* include Marvel NBASE T Phy functions */
+#include "m88x33xx/m88x33xx.h"
+#endif
+
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/version.h>
+
+/*************************/
+/* s2imac driver calls */
+/*************************/
+
+#ifndef CONFIG_S2IMAC_POLLING
+/**
+ * s2imac_enable_interrupts - Enable the interrupts for the s2imac device
+ * @drvdata:  Pointer to the s2imac device private data
+ *
+ * This function enables the Tx and Rx interrupts for the s2imac device along
+ * with the Global Interrupt Enable.
+ */
+static void s2imac_enable_interrupts(struct net_local *lp)
+{
+  u32 reg_data;
+
+  /* clear XGigE interrupts */
+  out_be32 ((u32 *) INT_REQ,  INT_ENABLE_TX | INT_ENABLE_RX);
+  
+  /* get interrput mask register */
+  reg_data = in_be32((u32 *) INT_MASK);
+
+  /* Enable the Tx interrupts, enable Rx interrupts and enable the global interrupt */
+  out_be32 ((u32 *) INT_MASK, reg_data | INT_ENABLE_TX | INT_ENABLE_RX | INT_ENABLE_IRQS);
+  
+  /* clear RX_LEN register */  
+  out_be32 ((u32 *) RX_LEN, 0);
+}
+
+/**
+ * s2imac_disable_interrupts - Disable the interrupts for the s2imac device
+ * @drvdata:  Pointer to the s2imac device private data
+ *
+ * This function disables the Tx and Rx interrupts for the s2imac device,
+ * along with the Global Interrupt Enable.
+ */
+static void s2imac_disable_interrupts(struct net_local *lp)
+{
+  u32 reg_data;
+  
+  /* get interrput mask register */
+  reg_data = in_be32((u32 *) INT_MASK);
+
+  /* disable the Tx interrupts, disable Rx interrupts and disable the global interrupt */
+  out_be32 ((u32 *) INT_MASK, reg_data & (~INT_ENABLE_TX) & (~INT_ENABLE_RX) & (~INT_ENABLE_IRQS));
+}
+#endif
+
+/* Read Ethernet PHY register */
+static u16 s2imac_phy_read (struct net_local *lp, u8 reg_addr)
+{
+  u32 ret;
+  int retries = 0;
+  
+  if (in_be32 ((u32 *) MDIO_ACC) & MDIO_ACC_NBLOCK) {
+    /*
+     * Non-blocking mode
+     * (only this software thread waits for MDIO access)
+     */
+    ret = in_be32 ((u32 *) (MDIO_BASE + ((lp->phy_addr & 0x1F) << 7)
+          + ((reg_addr & 0x1F) << 2)));
+
+    /*
+     * Wait here polling, until the value is ready to be read.
+     * Should we avoid endless loop due to hardware?
+     */
+    do {
+      ret = in_be32 ((u32 *) MDIO_ACC);
+      retries++;
+      if(retries > TIMEOUT_READ_WRITE_PHY)
+        break;
+    } while (!(ret & MDIO_ACC_MIIRDY));
+    /*
+     * read the value
+     */
+    ret = in_be32 ((u32 *) MDIO_ACC);
+  } else {
+    /*
+     * Blocking mode
+     * (whole system waits for the bus transaction to finish)
+     */
+    ret = in_be32 ((u32 *) (MDIO_BASE + ((lp->phy_addr & 0x1F) << 7)
+          + ((reg_addr & 0x1F) << 2)));
+  }
+  return (u16) (ret & 0xFFFF);
+}
+
+static u16 s2imac_phy_read1 (struct net_local *lp, u8 reg_addr)
+{
+  u32 ret;
+  int retries = 0;
+
+  if (in_be32 ((u32 *) MDIO_ACC) & MDIO_ACC_NBLOCK) {
+    /*
+     * Non-blocking mode
+     * (only this software thread waits for MDIO access)
+     */
+    ret = in_be32 ((u32 *) (MDIO_BASE1 + ((lp->phy_addr & 0x1F) << 7)
+          + ((reg_addr & 0x1F) << 2)));
+
+    /*
+     * Wait here polling, until the value is ready to be read.
+     * Should we avoid endless loop due to hardware?
+     */
+    do {
+      ret = in_be32 ((u32 *) MDIO_ACC);
+      retries++;
+      if(retries > TIMEOUT_READ_WRITE_PHY)
+        break;
+    } while (!(ret & MDIO_ACC_MIIRDY));
+    /*
+     * read the value
+     */
+    ret = in_be32 ((u32 *) MDIO_ACC);
+  } else {
+    /*
+     * Blocking mode
+     * (whole system waits for the bus transaction to finish)
+     */
+    ret = in_be32 ((u32 *) (MDIO_BASE1 + ((lp->phy_addr & 0x1F) << 7)
+          + ((reg_addr & 0x1F) << 2)));
+  }
+  return (u16) (ret & 0xFFFF);
+}
+
+/* Write Ethernet PHY register */
+static void s2imac_phy_write (struct net_local *lp, u8 reg_addr, u16 reg_data)
+{
+  u32 ret;
+  int retries = 0;
+
+  if (in_be32 ((u32 *) MDIO_ACC) & MDIO_ACC_NBLOCK) {
+    /*
+     * Non-blocking mode
+     * (only this software thread waits for MDIO access)
+     */
+    out_be32 ((u32 *) (MDIO_BASE + (lp->phy_addr << 7)
+           + ((reg_addr) << 2)), reg_data);
+
+    /*
+     * Wait here polling, until the value is ready written.
+     * Should we avoid endless loop due to hardware?
+     */
+    do {
+      ret = in_be32 ((u32 *) MDIO_ACC);
+      retries++;
+      if(retries > TIMEOUT_READ_WRITE_PHY)
+        break;
+    } while (!(ret & MDIO_ACC_MIIRDY));
+  } else {
+    /*
+     * Blocking mode
+     * (whole system waits for the bus transaction to finish)
+     */
+    out_be32 ((u32 *) (MDIO_BASE + (lp->phy_addr << 7)
+           + ((reg_addr) << 2)), reg_data);
+  }
+}
+
+static void s2imac_phy_write_addr (struct net_local *lp, u8 reg_addr, u16 reg_data)
+{
+  u32 ret;
+  int retries = 0;
+
+  if (in_be32 ((u32 *) MDIO_ACC) & MDIO_ACC_NBLOCK) {
+    /*
+     * Non-blocking mode
+     * (only this software thread waits for MDIO access)
+     */
+    out_be32 ((u32 *) (MDIO_BASE1 + (lp->phy_addr << 7)
+           + ((reg_addr) << 2)), reg_data);
+
+    /*
+     * Wait here polling, until the value is ready written.
+     * Should we avoid endless loop due to hardware?
+     */
+    do {
+      ret = in_be32 ((u32 *) MDIO_ACC);
+      retries++;
+      if(retries > TIMEOUT_READ_WRITE_PHY)
+        break;
+    } while (!(ret & MDIO_ACC_MIIRDY));
+  } else {
+    /*
+     * Blocking mode
+     * (whole system waits for the bus transaction to finish)
+     */
+    out_be32 ((u32 *) (MDIO_BASE1 + (lp->phy_addr << 7)
+           + ((reg_addr) << 2)), reg_data);
+  }
+}
+
+/* Extended PHY read */
+u16 s2imac_mdio_read(struct net_local *lp, u8 reg, u16 addr)
+{
+    s2imac_phy_write_addr(lp, reg, addr);
+    return s2imac_phy_read1(lp, reg);
+}
+
+/* Extended PHY write */
+void s2imac_mdio_write(struct net_local *lp, u8 reg, u16 addr, u16 val)
+{
+    s2imac_phy_write_addr(lp, reg, addr);
+    s2imac_phy_write(lp, reg, val);
+    return;
+}
+
+/*
+ * Detect the PHY address by scanning addresses 0 to 31 and
+ * looking at the MII status register (register 1) and assuming
+ * the PHY supports 10Mbps full/half duplex. Feel free to change
+ * this code to match your PHY, or hardcode the address if needed.
+ *
+ * Use MII register 1 (MII status register) to detect PHY
+ *
+ * Mask used to verify certain PHY features (or register contents)
+ * in the register above:
+ *  0x1000: 10Mbps full duplex support
+ *  0x0800: 10Mbps half duplex support
+ *  0x0008: Auto-negotiation support
+ */
+#define PHY_DETECT_REG    1
+#define PHY_DETECT_MASK   0x1808
+static int detect_phy (struct net_local *lp, struct device *dev)
+{
+  u16 phy_reg;
+
+  for (lp->phy_addr = 31; (int)lp->phy_addr >= 0; lp->phy_addr--) {
+    phy_reg = s2imac_phy_read (lp, PHY_DETECT_REG);
+    if (phy_reg != 0xFFFF) {
+//    if ((phy_reg != 0xFFFF) && ((phy_reg & PHY_DETECT_MASK)
+//              == PHY_DETECT_MASK)) {
+      /* Found a valid PHY address */
+      dev_info (dev, "PHY detected at address %d.\n",
+          lp->phy_addr);
+      return lp->phy_addr;
+    }
+  }
+  /* default to zero */
+  dev_info (dev, "No PHY detected. Assuming a PHY at address  %d.\n", lp->phy_addr);
+  return lp->phy_addr;
+}
+
+static void set_mac_speed (struct net_local *lp)
+{
+  u32 cfg  = 0x80000000;      /* Default 1 Gbps */
+  u32 rxtx = 0x10000000;      /* Enabled by default */
+  struct net_device *ndev = lp->ndev;
+  u32 id;
+//  u16 tmp;
+//  int i, retries;
+//  unsigned retries = 10;
+
+  /* wait for link up */
+//  while (retries-- && ((s2imac_phy_read (lp, 1) & 0x24) != 0x24)) ;
+
+  /* get PHY id */
+  id = (s2imac_phy_read (lp, 2) << 16)
+      | s2imac_phy_read (lp, 3);
+
+  /*
+   * Marwell 88e1111 id 0x1410cc2 - ml50x, ml605, ZC702, ZC706, / 88e1512 id 0x1410dd1 - SVDK
+   */
+  /* FIXME this part will be replaced by PHY lib */
+  if ((id == 0x1410cc2) || (id == 0x1410dd1)) {
+    switch ((s2imac_phy_read (lp, 0x11)) & 0xE000) {
+    case 0x0000:
+      /* 10BASE-T, half-duplex */
+      cfg = MDIO_EMMC_10BASET;
+      rxtx = (MDIO_RXTX_ENABLE | MDIO_RXTX_HALFDUPLEX);
+      lp->cur_speed = 10;
+      dev_info (&ndev->dev, "speed set to 10BASE-T/HD\n");
+      break;
+    case 0x2000:
+      /* 10BASE-T, full-duplex */
+      cfg = MDIO_EMMC_10BASET;
+      rxtx = MDIO_RXTX_ENABLE;
+      lp->cur_speed = 10;
+      dev_info (&ndev->dev, "speed set to 10BASE-T/FD\n");
+      break;
+    case 0x4000:
+      /* 100BASE-TX, half-duplex */
+      cfg = MDIO_EMMC_100BASET;
+      rxtx = (MDIO_RXTX_ENABLE | MDIO_RXTX_HALFDUPLEX);
+      lp->cur_speed = 100;
+      dev_info (&ndev->dev, "speed set to 100BASE-T/HD\n");
+      break;
+    case 0x6000:
+      /* 100BASE-TX, full-duplex */
+      cfg = MDIO_EMMC_100BASET;
+      rxtx = MDIO_RXTX_ENABLE;
+      lp->cur_speed = 100;
+      dev_info (&ndev->dev, "speed set to 100BASE-T/FD\n");
+      break;
+    case 0x8000:
+      /* 1000BASE-T, half-duplex */
+      cfg = MDIO_EMMC_1000BASET;
+      rxtx = (MDIO_RXTX_ENABLE | MDIO_RXTX_HALFDUPLEX);
+      lp->cur_speed = 1000;
+      dev_info (&ndev->dev, "speed set to 1000BASE-T/HD\n");
+      break;
+    case 0xA000:
+      /* 1000BASE-T, full-duplex */
+      cfg = MDIO_EMMC_1000BASET;
+      rxtx = MDIO_RXTX_ENABLE;
+      lp->cur_speed = 1000;
+      dev_info (&ndev->dev, "speed set to 1000BASE-T/FD\n");
+      break;
+    default:
+      return;
+    }
+    lp->phy_type = PHY_MARVELL;
+  }
+  else if(id == 0x0143BD63){
+    /*
+    * Broadcom BCM54610 id 0x0143BD63
+    */
+    switch ((s2imac_phy_read (lp, 0x19)) & 0x0700) {
+    case 0x0100:
+      /* 10BASE-T, half-duplex */
+      cfg = MDIO_EMMC_10BASET;
+      rxtx = (MDIO_RXTX_ENABLE | MDIO_RXTX_HALFDUPLEX);
+      lp->cur_speed = 10;
+      dev_info (&ndev->dev, "speed set to 10BASE-T/HD\n");
+      break;
+    case 0x0200:
+      /* 10BASE-T, full-duplex */
+      cfg = MDIO_EMMC_10BASET;
+      rxtx = MDIO_RXTX_ENABLE;
+      lp->cur_speed = 10;
+      dev_info (&ndev->dev, "speed set to 10BASE-T/FD\n");
+      break;
+    case 0x0300:
+      /* 100BASE-TX, half-duplex */
+      cfg = MDIO_EMMC_100BASET;
+      rxtx = (MDIO_RXTX_ENABLE | MDIO_RXTX_HALFDUPLEX);
+      lp->cur_speed = 100;
+      dev_info (&ndev->dev, "speed set to 100BASE-T/HD\n");
+      break;
+    case 0x0500:
+      /* 100BASE-TX, full-duplex */
+      cfg = MDIO_EMMC_100BASET;
+      rxtx = MDIO_RXTX_ENABLE;
+      lp->cur_speed = 100;
+      dev_info (&ndev->dev, "speed set to 100BASE-T/FD\n");
+      break;
+    case 0x0600:
+      /* 1000BASE-T, half-duplex */
+      cfg = MDIO_EMMC_1000BASET;
+      rxtx = (MDIO_RXTX_ENABLE | MDIO_RXTX_HALFDUPLEX);
+      lp->cur_speed = 1000;
+      dev_info (&ndev->dev, "speed set to 1000BASE-T/HD\n");
+      break;
+    case 0x0700:
+      /* 1000BASE-T, full-duplex */
+      cfg = MDIO_EMMC_1000BASET;
+      rxtx = MDIO_RXTX_ENABLE;
+      lp->cur_speed = 1000;
+      dev_info (&ndev->dev, "speed set to 1000BASE-T/FD\n");
+      break;
+    default:
+      return;
+    }
+    /* Set PHY autonegotiation registers */
+    s2imac_phy_write (lp, 4, 0x01E1);
+    s2imac_phy_write (lp, 9, 0x0300);
+    /* Setup PHY LEDs
+    *   - activity LED indicates even link utilization
+    *   - LED1 = off, LED2 = activity
+    *   - LED3 = off, LED4 = link quality
+    */
+    s2imac_phy_write (lp, 0x1C, 0xA40B); 
+    s2imac_phy_write (lp, 0x1C, 0xB43E);
+    s2imac_phy_write (lp, 0x1C, 0xB87E);
+    
+    lp->phy_type = PHY_BROADCOM;
+  }
+  else {
+
+    if(lp->phy_base_addr == 0) {
+      if(lp->init_phy == 0) {
+          out_be32 ((u32 *) MC, MDIO_ENABLE_MASK1 | MDIO_CLOCK_DIV1);
+        lp->phy_addr = detect_phy (lp, &ndev->dev);
+      }
+
+      /* check if phy is NBASE-T Marvell PHY */
+      id = ((s2imac_mdio_read (lp, 1, 2) << 16) | s2imac_mdio_read (lp, 1, 3)) & 0xFFFFFFFC;
+    } else 
+      id = 0;
+    
+    if(id == 0x2B09A8) {
+#ifdef NBASE_T_MARVELL
+
+      if(lp->init_phy == 0) {
+
+        dev_info (&ndev->dev, "Init NBASE-T Marvell PHY [%X] ...\n", id);
+        
+        s2imac_mdio_write(lp, 31, 0xF001, (s2imac_mdio_read(lp, 31, 0xF001) & 0xFFF8) | 0x0001);  // XAUI mode
+        s2imac_mdio_write(lp, 31, 0xF001,  s2imac_mdio_read(lp, 31, 0xF001)           | 0x8000);  // SW reset
+  
+        i = m88x33xx_init(lp, RXAUI);
+        if(i != 0)
+          dev_err (&ndev->dev, "Error m88x33xx_init: %d\n", i);
+        else {
+          lp->init_phy = 1;
+          
+          retries = 50;
+          while (retries-- && ((s2imac_mdio_read (lp, 0x03, 0x8008) & 0x0400) == 0)) 
+            //udelay(200000);
+            mdelay(200);
+        }
+      }
+      
+      /* Setup XGMAC speed throttling and GEV link speed register */
+      tmp = s2imac_mdio_read(lp, 0x03, 0x8008);
+      switch (tmp & 0xC000) {
+          /* 10Mbps */
+          case 0x0000:    out_be32 ((u32 *) SPEED, NBASET_SPD_1000);
+                          lp->cur_speed = 10;
+                          dev_info (&ndev->dev, "speed set to 10BASE-T/FD\n");
+                          break;
+          /* 100Mbps */
+          case 0x4000:    out_be32 ((u32 *) SPEED, NBASET_SPD_1000);
+                          lp->cur_speed = 100;
+                          dev_info (&ndev->dev, "speed set to 100BASE-T/FD\n");
+                          break;
+          /* 1Gbps */
+          case 0x8000:    out_be32 ((u32 *) SPEED, NBASET_SPD_1000);
+                          lp->cur_speed = 1000;
+                          dev_info (&ndev->dev, "speed set to 1000BASE-T/FD\n");
+                          break;
+          /* 10Gbps + NBASE-T */
+          case 0xC000:    switch (tmp & 0x000C) {
+          /* 2.5Gbps */
+          case 0x0004:    out_be32 ((u32 *) SPEED, NBASET_SPD_2500);
+                          lp->cur_speed = 2500;
+                          dev_info (&ndev->dev, "speed set to 2500BASE-T/FD\n");
+                          break;
+          /* 5Gbps */
+          case 0x0008:    out_be32 ((u32 *) SPEED, NBASET_SPD_5G);
+                          lp->cur_speed = 5000;
+                          dev_info (&ndev->dev, "speed set to 5000BASE-T/FD\n");
+                          break;
+          /* 10Gbps */
+          default:        out_be32 ((u32 *) SPEED, NBASET_SPD_10G);
+                          lp->cur_speed = 10000;
+                          dev_info (&ndev->dev, "speed set to 10000BASE-T/FD\n");
+                          break;
+        }
+        break;
+      }
+      
+      lp->phy_type = PHY_NBASET_MRVL;
+      rxtx = MDIO_RXTX_ENABLE;
+#endif    
+    } else {      
+    
+      // Xilinx 10/25-Gigabit Ethernet PCS/PMA IP core
+       lp->phy_type = PHY_25G_PCS_PMA;
+      // 10/25GBASE-SR, full-duplex
+      rxtx = MDIO_RXTX_ENABLE;
+
+      dev_info (&ndev->dev, "PHY: Xilinx 10/25-Gigabit Ethernet PCS/PMA IP core\n");
+
+      if (in_be32 ((u32 *)(lp->phy_base_addr + 0x0498)) & 0x00000001) {
+        lp->cur_speed = 10000;
+        dev_info (&ndev->dev, "speed set to 10000BASE-T/FD\n");
+      } else {
+        lp->cur_speed = 25000;
+        dev_info (&ndev->dev, "speed set to 25000BASE-T/FD\n");
+      }
+    }
+  }
+  
+  if((lp->phy_type == PHY_MARVELL) || (lp->phy_type == PHY_BROADCOM)) {
+    out_be32 ((u32 *) EMMC, cfg);
+  }
+    
+  /* Enable jumbo frames for Tx and Rx */
+  out_be32 ((u32 *) TC, rxtx | MDIO_RXTX_JUMBO);
+  out_be32 ((u32 *) RCW1, rxtx | MDIO_RXTX_JUMBO);
+}
+
+/*
+ * Perform any necessary special phy setup. In the gmii case, nothing needs to
+ * be done.
+ */
+static void phy_setup (struct net_local *lp, struct net_device *dev)
+{
+  u32 reg;
+  unsigned retries = 10;
+
+  /* non-blocking PHY access enabled (if supported) */
+  out_be32 ((u32 *) MDIO_ACC, MDIO_ACC_ENA_NBLOCK);
+
+  /* wait for end of PHY reset */
+  do {
+    reg = in_be32 ((u32 *) GCSR);
+  } while (reg & GCSR_RST_PHY);
+
+  /*
+   * Setup timers and clock generators
+   *   - timeout counter clock period 1 ms
+   *   - PHY MDC frequency (max 2.5 MHz according to IEEE Std 802.3-2002,
+   *     BCM5461A supports 12.5 MHz)
+   */
+  out_be32 ((u32 *) CLK_FREQ, lp->coreclk);
+  out_be32 ((u32 *) TOCNT_DIV, (lp->coreclk / 1000) - 1);
+  out_be32 ((u32 *) MC, MDIO_ENABLE_MASK | MDIO_CLOCK_DIV);
+
+  /* wait for link up */
+  while (retries-- && ((s2imac_phy_read (lp, 1) & 0x24) != 0x24)) ;
+}
+
+/*
+ * The PHY registers read here should be standard registers in all PHY chips
+ */
+static int get_phy_status (struct net_device *ndev, int *linkup)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  u16 reg;
+
+  if((lp->phy_type == PHY_MARVELL) || (lp->phy_type == PHY_BROADCOM)) {
+    reg = s2imac_phy_read (lp, MII_BMSR);
+    *linkup = (reg & BMSR_LSTATUS) != 0;
+  } else if(lp->phy_type == PHY_25G_PCS_PMA) {
+    // 10GBASE-R Xilinx 10/25Gbps PCS/PMA IP core
+    *linkup = in_be32 ((u32 *)(lp->phy_base_addr + 0x040C)) & 0x00000001;
+  } else {
+    if((s2imac_mdio_read (lp, 0x03, 0x8008) & 0x0400) == 0)
+      *linkup = 0;
+    else
+      *linkup = 1;
+  }
+//BMSR_ANEGCOMPLETE
+  return 0;
+}
+
+/*
+ * This routine is used for two purposes. The first is to keep s2imac
+ * EMAC's duplex setting in sync with the PHY's. The second is to keep
+ * the system apprised of the state of the link. Note that this driver
+ * does not configure the PHY. Either the PHY should be configured for
+ * auto-negotiation or it should be handled by something like mii-tool.
+ */
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+static void poll_gmii (unsigned long data)
+#else
+static void poll_gmii (struct timer_list *data)
+#endif
+{
+  struct net_device *ndev;
+  struct net_local *lp;
+  int phy_carrier;
+  int netif_carrier;
+  u32 reg;
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+  ndev = (struct net_device *)data;
+  lp = (struct net_local *)netdev_priv (ndev);
+#else  
+  lp = from_timer(lp, data, phy_timer);
+  ndev = lp->ndev;
+#endif  
+
+  /* first, find out what's going on with the PHY */
+  if (get_phy_status (ndev, &phy_carrier)) {
+    dev_err (&ndev->dev, "terminating link monitoring\n");
+    return;
+  }
+
+  netif_carrier = netif_carrier_ok (ndev) != 0;
+
+ 
+  if (phy_carrier != netif_carrier) {
+    if (phy_carrier) {
+
+      /* Reset PHY/MAC
+      *  (workaround to avoid problems with out of DCM
+      *  specification clocks in the 10 Mbps mode)
+      */
+      reg = in_be32 ((u32 *) GCSR);
+      reg |= GCSR_RST_PHY;
+      out_be32 ((u32 *) GCSR, reg);
+
+      /* wait for end of PHY reset */
+      do {
+        reg = in_be32 ((u32 *) GCSR);
+      } while (reg & GCSR_RST_PHY);
+
+      set_mac_speed (lp);
+
+      /* enable receive and transmit clients */
+      reg = in_be32 ((u32 *) GCSR);
+      reg |= (GCSR_CONNECTED | GCSR_LITTLE_ENDIAN);
+      out_be32 ((u32 *) GCSR, reg);
+
+			dev_info (&ndev->dev, "PHY link carrier restored\n");
+      netif_carrier_on (ndev);
+
+    } else {
+
+      /* Periodically restart autonegotiation */
+      if((lp->phy_type == PHY_MARVELL) || (lp->phy_type == PHY_BROADCOM)) {
+        if (s2imac_phy_read(lp, 0x01) & 0x0020)
+          s2imac_phy_write(lp, 0x00, s2imac_phy_read(lp, 0x00) | 0x0200);
+      }
+
+      /* disable receive and transmit clients */
+      reg = in_be32 ((u32 *) GCSR);
+      reg &= ~GCSR_CONNECTED;
+      out_be32 ((u32 *) GCSR, reg);
+
+      dev_info (&ndev->dev, "PHY link carrier lost\n");
+      netif_carrier_off (ndev);
+    }
+  }
+
+  /* Set up the timer so we'll get called again in 2 seconds. */
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+  lp->phy_timer.expires = jiffies + 2 * HZ;
+  add_timer (&lp->phy_timer);
+#else
+  mod_timer(&lp->phy_timer, jiffies + 2 * HZ);
+#endif
+}
+
+/**
+ * s2imac_send_data - Send an Ethernet frame
+ * @lp:   Pointer to the s2imac device private data
+ * @data: Pointer to the data to be sent
+ * @byte_count: Total frame size, &lp->ndev->devincluding header
+ *
+ * This function checks if the Tx buffer of the s2imac device is free to send
+ * data. If so, it fills the Tx buffer with data for transmission. Otherwise, it
+ * returns an error.
+ *
+ * Return:  0 upon success or -1 if the buffer(s) are full.
+ *
+ * Note:  The maximum Tx packet size can not be more than Ethernet header
+ *    (14 Bytes) + Maximum MTU (1500 bytes). This is excluding FCS.
+ */
+static int s2imac_send_data (struct net_local *lp, u8 * data,
+           unsigned int byte_count)
+{
+  u16 *to_u16_ptr, val;
+  u32 len, i, len_rx, *to_u32_ptr, align_buffer,j;
+  u8 *to_u8_ptr, *from_u8_ptr;
+
+#ifndef CONFIG_S2IMAC_POLLING
+  if(in_be32 ((u32 *) TX_LEN))
+    return -1; /* Buffer was full, return failure */
+#endif
+
+  /* If the length is too large, truncate it */
+  if (byte_count > ETH_FRAME_LEN)
+    byte_count = ETH_FRAME_LEN;
+  
+  len = ((byte_count - 2) / 4);
+  to_u16_ptr = (u16 *)data;
+
+  // first 2 bytes of buffer not used 
+  val = *to_u16_ptr++;
+  lp->gige_txbuf[0] = (u32) (((u32) val << 16) | (u32) 0x0000);
+
+  to_u32_ptr = (u32 *)to_u16_ptr;
+	
+  len_rx = 2;
+  for (i = 1; i <= len; i++) {
+    lp->gige_txbuf[i] = *to_u32_ptr++;
+    len_rx += 4;
+  }
+
+  // if there are data available, send it 
+  if(len_rx != byte_count)  {
+      len = byte_count - len_rx;
+      align_buffer = 0;
+      to_u8_ptr = (u8 *)&align_buffer;
+      from_u8_ptr = (u8 *)to_u32_ptr;
+      for (j = 0; j < len; j++) 
+        *to_u8_ptr++ = *from_u8_ptr++;
+      lp->gige_txbuf[i] = align_buffer;
+  }
+  
+  /* send reply */
+  while (in_be32 ((u32 *) TX_LEN)) { 
+  };
+  out_be32 ((u32 *) TX_LEN, byte_count);
+
+  //dev_info (&lp->ndev->dev, "send: %d\n",in_be32 ((u32 *) TX_LEN));
+
+  return 0;
+}
+
+#ifndef CONFIG_S2IMAC_POLLING
+/**********************/
+/* Interrupt Handlers */
+/**********************/
+
+/**
+ * s2imac_tx_handler - Interrupt handler for frames sent
+ * @dev:  Pointer to the network device
+ *
+ * This function updates the number of packets transmitted and handles the
+ * deferred skb, if there is one.
+ */
+static void s2imac_tx_handler(struct net_device *dev)
+{
+  struct net_local *lp = (struct net_local *) netdev_priv(dev);
+      
+  if (lp->deferred_skb) {
+    dev->stats.tx_packets++;
+    if (s2imac_send_data(lp,
+          (u8 *) lp->deferred_skb->data,
+          lp->deferred_skb->len) == 0) {
+      dev->stats.tx_bytes += lp->deferred_skb->len;
+      dev_kfree_skb_irq(lp->deferred_skb);
+      lp->deferred_skb = NULL;
+#ifdef HAVE_TRANS_START_HELPER
+      netif_trans_update(dev);
+#else
+      dev->trans_start = jiffies;
+#endif
+      netif_wake_queue(dev);
+    }
+  }
+  /* clear tx interrupt */
+  out_be32 ((u32 *) INT_REQ,  INT_ENABLE_TX);
+}
+
+/**
+ * s2imac_rx_handler- Interrupt handler for frames received
+ * @dev:  Pointer to the network device
+ *
+ * This function allocates memory for a socket buffer, fills it with data
+ * received and hands it over to the TCP/IP stack.
+ */
+static void s2imac_rx_handler(struct net_device *dev)
+{
+  struct net_local *lp = (struct net_local *) netdev_priv(dev);
+  struct sk_buff *skb;
+  unsigned int align;
+  u32 len, l, i, align_buffer,len_rx;
+  u8 *to_u8_ptr, *from_u8_ptr;
+  u32 *to_u32_ptr;
+
+  len = in_be32 ((u32 *) RX_LEN);
+	
+//  dev_info (&dev->dev, "[INFO] - IRQ IN: %d\n", len);
+
+  if (len) {
+    skb = dev_alloc_skb (len + ALIGNMENT);
+    if (!skb) {
+      dev->stats.rx_dropped++;
+      dev_err (&dev->dev,
+         "Could not allocate receive buffer\n");
+      return;
+    }
+
+    /*
+     * A new skb should have the data halfword aligned, but this code is
+     * here just in case that isn't true. Calculate how many
+     * bytes we should reserve to get the data to start on a word
+     * boundary
+     */
+    align = BUFFER_ALIGN (skb->data);
+    if (align)
+      skb_reserve (skb, align);
+
+    skb_reserve (skb, 2);
+
+    l = (len / 4);
+
+    to_u32_ptr = (u32 *)skb->data;
+    len_rx = 0;
+    for (i = 0; i < l; i++) 
+    {
+      align_buffer = ((lp->gige_rxbuf[i] >> 16) | (lp->gige_rxbuf[i + 1] << 16));
+      *to_u32_ptr++ = align_buffer;
+      len_rx += 4;
+    }
+
+    if(len != len_rx)
+    {
+      l = len - len_rx;
+      align_buffer = ((lp->gige_rxbuf[i] >> 16) | (lp->gige_rxbuf[i + 1] << 16));
+      to_u8_ptr = (u8 *)to_u32_ptr;
+      from_u8_ptr = (u8 *)&align_buffer;
+      for (i = 0; i < l; i++) 
+        *to_u8_ptr++ = *from_u8_ptr++;
+    }
+
+    skb_put (skb, len); /* Tell the skb how much data we got */
+    skb->dev = dev; /* Fill out required meta-data */
+
+    skb->protocol = eth_type_trans (skb, dev);
+    skb->ip_summed = CHECKSUM_NONE;
+
+    dev->stats.rx_packets++;
+    dev->stats.rx_bytes += len;
+
+    if (!skb_defer_rx_timestamp(skb))
+      netif_rx (skb); /* Send the packet upstream */
+  }
+  
+  /* clear rx interrupt */
+  out_be32 ((u32 *) INT_REQ,  INT_ENABLE_RX);
+  out_be32 ((u32 *) RX_LEN, 0);
+}
+
+/**
+ * s2imac_interrupt - Interrupt handler for this driver
+ * @irq:  Irq of the s2imac device
+ * @dev_id: Void pointer to the network device instance used as callback
+ *    reference
+ *
+ * This function handles the Tx and Rx interrupts of the s2imac device.
+ */
+static irqreturn_t s2imac_interrupt(int irq, void *dev_id)
+{
+  struct net_device *dev = dev_id;
+  struct net_local *lp = (struct net_local *) netdev_priv(dev);
+  u32 reg_data;
+  unsigned long flags;
+
+  spin_lock_irqsave (&lp->reset_lock, flags);
+
+  /* read the irq status */
+  reg_data = in_be32((u32 *) INT_REQ);
+
+  /* check if rx interrupt */
+  if((reg_data & INT_ENABLE_RX) == INT_ENABLE_RX)
+    s2imac_rx_handler(dev);
+
+  /* check if tx interrupt */
+  if((reg_data & INT_ENABLE_TX) == INT_ENABLE_TX)
+    s2imac_tx_handler(dev);
+
+  spin_unlock_irqrestore (&lp->reset_lock, flags);
+
+  return IRQ_HANDLED;
+}
+
+#else
+
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+static void s2imac_irq_timer (unsigned long data)
+#else
+static void s2imac_irq_timer (struct timer_list *data)
+#endif
+{
+  struct net_device *ndev;
+  struct net_local *lp;
+//  struct net_device *ndev = (struct net_device *)data;
+//  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  struct sk_buff *skb;
+  unsigned int align;
+  u32 len, l, i, align_buffer,len_rx;
+  u16 *to_u16_ptr;
+  u16 *from_u16_ptr;
+  u32 *to_u32_ptr;
+  u16 w1, w2;
+  u8 *to_u8_ptr, *from_u8_ptr;
+
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+  ndev = (struct net_device *)data;
+  lp = (struct net_local *)netdev_priv (ndev);
+#else  
+  lp = from_timer(lp, data, irq_timer);
+  ndev = lp->ndev;
+#endif  
+  
+  
+  len = in_be32 ((u32 *) RX_LEN);
+  if (len) {
+    skb = dev_alloc_skb (len + ALIGNMENT);
+    if (!skb) {
+      ndev->stats.rx_dropped++;
+      dev_err (&ndev->dev,
+        "Could not allocate receive buffer\n");
+      return;
+    }
+
+    /*
+     * A new skb should have the data halfword aligned, but this code is
+     * here just in case that isn't true. Calculate how many
+     * bytes we should reserve to get the data to start on a word
+     * boundary
+     */
+    align = BUFFER_ALIGN (skb->data);
+    if (align)
+      skb_reserve (skb, align);
+
+    skb_reserve (skb, 2);
+
+    l = (len / 4);
+
+    to_u32_ptr = (u32 *)skb->data;
+    len_rx = 0;
+    for (i = 0; i < l; i++) 
+    {
+      align_buffer = ((lp->gige_rxbuf[i] >> 16) | (lp->gige_rxbuf[i + 1] << 16));
+      *to_u32_ptr++ = align_buffer;
+      len_rx += 4;
+    }
+
+    if(len != len_rx)
+    {
+      l = len - len_rx;
+      align_buffer = ((lp->gige_rxbuf[i] >> 16) | (lp->gige_rxbuf[i + 1] << 16));
+      to_u8_ptr = (u8 *)to_u32_ptr;
+      from_u8_ptr = (u8 *)&align_buffer;
+      for (i = 0; i < l; i++) 
+        *to_u8_ptr++ = *from_u8_ptr++;
+    }
+
+    skb_put (skb, len); /* Tell the skb how much data we got */
+    skb->dev = ndev;  /* Fill out required meta-data */
+
+    skb->protocol = eth_type_trans (skb, ndev);
+    skb->ip_summed = CHECKSUM_NONE;
+
+    ndev->stats.rx_packets++;
+    ndev->stats.rx_bytes += len;
+
+    if (!skb_defer_rx_timestamp(skb))
+      netif_rx (skb);   /* Send the packet upstream */
+
+    out_be32 ((u32 *) RX_LEN, 0);
+  }
+
+  mod_timer (&lp->irq_timer, jiffies);
+}
+#endif
+
+/**
+ * s2imac_update_address - Update the MAC address in the device
+ * @lp:   Pointer to the s2imac device private data
+ * @address_ptr:Pointer to the MAC address (MAC address is a 48-bit value)
+ *
+ * Tx must be idle and Rx should be idle for deterministic results.
+ * It is recommended that this function should be called after the
+ * initialization and before transmission of any packets from the device.
+ * The MAC address can be programmed using any of the two transmit
+ * buffers (if configured).
+ */
+static void s2imac_update_address (struct net_local *lp, u8 * address_ptr)
+{
+  u32 val;
+  u32 mac_l, mac_h;
+
+  /* set up unicast MAC address filter */
+  val = ((address_ptr[3] << 24) | (address_ptr[2] << 16) |
+         (address_ptr[1] << 8) | (address_ptr[0]));
+  out_be32 ((u32 *) UAW0, val);
+  val = (address_ptr[5] << 8) | address_ptr[4];
+  out_be32 ((u32 *) UAW1, val);
+
+  mac_h = (address_ptr[0] << 8) | address_ptr[1];
+  mac_l = ((address_ptr[2] << 24) | (address_ptr[3] << 16) |
+     (address_ptr[4] << 8) | (address_ptr[5]));
+  out_be32 ((u32 *) MAC_HIGH, mac_h); /* set gige_mac_h register */
+  out_be32 ((u32 *) MAC_LOW, mac_l);  /* set gige_mac_l register */
+  out_be32 ((u32 *) MAC_RX_HIGH, mac_h);  /* set gige_rx_mac_h register */
+  out_be32 ((u32 *) MAC_RX_LOW, mac_l); /* set gige_rx_mac_l register */
+}
+
+/**
+ * s2imac_set_mac_address - Set the MAC address for this device
+ * @dev:  Pointer to the network device instance
+ * @addr: Void pointer to the sockaddr structure
+ *
+ * This function copies the HW address from the sockaddr strucutre to the
+ * net_device structure and updates the address in HW.
+ *
+ * Return:  Error if the net device is busy or 0 if the addr is set
+ *    successfully
+ */
+static int s2imac_set_mac_address (struct net_device *ndev, void *address)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  struct sockaddr *addr = address;
+
+  if (netif_running (ndev))
+    return -EBUSY;
+
+  memcpy (ndev->dev_addr, addr->sa_data, ndev->addr_len);
+  s2imac_update_address (lp, ndev->dev_addr);
+  return 0;
+}
+
+/**
+ * s2imac_tx_timeout - Callback for Tx Timeout
+ * @dev:  Pointer to the network device
+ *
+ * This function is called when Tx time out occurs for s2imac device.
+ */
+static void s2imac_tx_timeout (struct net_device *ndev, unsigned int val)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  unsigned long flags;
+#ifdef HAVE_TRANS_START_HELPER
+  struct netdev_queue *txq = netdev_get_tx_queue(ndev, 0);
+#endif
+  
+  dev_err (&ndev->dev, "Exceeded transmit timeout of %lu ms\n",
+     TX_TIMEOUT * 1000UL / HZ);
+
+  ndev->stats.tx_errors++;
+
+  /* Reset the device */
+  spin_lock_irqsave (&lp->reset_lock, flags);
+
+  /* Shouldn't really be necessary, but shouldn't hurt */
+  netif_stop_queue (ndev);
+
+#ifndef CONFIG_S2IMAC_POLLING
+  s2imac_disable_interrupts(lp);
+  s2imac_enable_interrupts(lp);
+#endif  
+
+  //out_be32 ((u32 *) TX_LEN, byte_count);
+
+  if (lp->deferred_skb) {
+    dev_kfree_skb (lp->deferred_skb);
+    lp->deferred_skb = NULL;
+    ndev->stats.tx_errors++;
+  }
+
+  /* To exclude tx timeout */
+#ifdef HAVE_TRANS_START_HELPER
+  txq->trans_start = 0xffffffff - TX_TIMEOUT - TX_TIMEOUT;
+#else
+  ndev->trans_start = 0xffffffff - TX_TIMEOUT - TX_TIMEOUT;
+#endif 
+  /* We're all ready to go. Start the queue */
+  netif_wake_queue (ndev);
+  spin_unlock_irqrestore (&lp->reset_lock, flags);
+}
+
+/**
+ * s2imac_open - Open the network device
+ * @dev:  Pointer to the network device
+ *
+ * This function sets the MAC address, requests an IRQ and enables interrupts
+ * for the s2imac device and starts the Tx queue.
+ * It also connects to the phy device, if MDIO is included in s2imac device.
+ */
+static int s2imac_open (struct net_device *ndev)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  int link;
+  u32 reg;
+#ifndef CONFIG_S2IMAC_POLLING
+  int retval;
+  s2imac_disable_interrupts(lp);
+#endif
+
+  /* Just to be safe, stop the device first */
+  netif_stop_queue (ndev);
+
+  /* Set the MAC address each time opened */
+  s2imac_update_address (lp, ndev->dev_addr);
+
+  /* transmit and receive packet buffers */
+  lp->gige_txbuf = (u32 *)TXBUF;
+  lp->gige_rxbuf = (u32 *)RXBUF;
+
+  /* setup phy */
+  set_mac_speed (lp);
+
+  /* if link if up enable connected bit */
+  get_phy_status (ndev, &link);
+
+  /* first read from PHY_25G_PCS_PMA always 0, need to fix */
+  if(lp->phy_type == PHY_25G_PCS_PMA)
+    link = 1;
+
+  if(link)
+  {
+    /* enable receive and transmit clients */
+    reg = in_be32 ((u32 *) GCSR);
+    reg |= (GCSR_CONNECTED | GCSR_LITTLE_ENDIAN);
+    out_be32 ((u32 *) GCSR, reg);
+  }  
+  
+#ifndef CONFIG_S2IMAC_POLLING
+  /* grab the IRQ */
+  retval = request_irq(ndev->irq, s2imac_interrupt, 0, ndev->name, ndev);
+  if (retval) {
+    dev_err(&lp->ndev->dev, "Could not allocate interrupt %d\n",
+      ndev->irq);
+    return retval;
+  }
+  
+  /* Enable Interrupts */
+  s2imac_enable_interrupts(lp);
+#else
+  mod_timer (&lp->irq_timer, jiffies);
+#endif
+
+  /* We're ready to go */
+  netif_start_queue (ndev);
+
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+  /* Set up the PHY monitoring timer. */
+  lp->phy_timer.expires = jiffies + 2 * HZ;
+  lp->phy_timer.data = (unsigned long)ndev;
+  lp->phy_timer.function = &poll_gmii;
+  init_timer (&lp->phy_timer);
+  add_timer (&lp->phy_timer);
+#else
+   timer_setup(&lp->phy_timer, &poll_gmii, 0);
+   mod_timer(&lp->phy_timer, jiffies + 2 * HZ);
+#endif
+  return 0;
+}
+
+/**
+ * s2imac_close - Close the network device
+ * @dev:  Pointer to the network device
+ *
+ * This function stops the Tx queue, disables interrupts and frees the IRQ for
+ * the s2imac device.
+ * It also disconnects the phy device associated with the s2imac device.
+ */
+static int s2imac_close (struct net_device *ndev)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  u32 reg;
+
+  netif_stop_queue (ndev);
+
+#ifndef CONFIG_S2IMAC_POLLING
+  s2imac_disable_interrupts(lp);
+  free_irq(ndev->irq, ndev);
+#endif
+	
+  /* Shut down the PHY monitoring timer. */
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+  del_timer_sync (&lp->phy_timer);
+#else
+  del_timer(&lp->phy_timer);
+#endif  
+  /* disable receive and transmit clients */
+  reg = in_be32 ((u32 *) GCSR);
+  reg &= ~GCSR_CONNECTED;
+  out_be32 ((u32 *) GCSR, reg);
+
+  return 0;
+}
+
+/**
+ * s2imac_get_stats - Get the stats for the net_device
+ * @dev:  Pointer to the network device
+ *
+ * This function returns the address of the 'net_device_stats' structure for the
+ * given network device. This structure holds usage statistics for the network
+ * device.
+ *
+ * Return:  Pointer to the net_device_stats structure.
+ */
+static struct net_device_stats *s2imac_get_stats (struct net_device *ndev)
+{
+  return &ndev->stats;
+}
+
+/**
+ * s2imac_send - Transmit a frame
+ * @orig_skb: Pointer to the socket buffer to be transmitted
+ * @dev:  Pointer to the network device
+ *
+ * This function checks if the Tx buffer of the s2imac device is free to send
+ * data. If so, it fills the Tx buffer with data from socket buffer data,
+ * updates the stats and frees the socket buffer. The Tx completion is signaled
+ * by an interrupt. If the Tx buffer isn't free, then the socket buffer is
+ * deferred and the Tx queue is stopped so that the deferred socket buffer can
+ * be transmitted when the s2imac device is free to transmit data.
+ *
+ * Return:  0, always.
+ */
+static int s2imac_send (struct sk_buff *orig_skb, struct net_device *ndev)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  struct sk_buff *new_skb;
+  unsigned int len;
+  unsigned long flags;
+
+  len = orig_skb->len;
+
+  new_skb = orig_skb;
+
+  spin_lock_irqsave (&lp->reset_lock, flags);
+
+  if (s2imac_send_data (lp, (u8 *) new_skb->data, len) != 0) {
+    /*
+     * If the s2imac Tx buffer is busy, stop the Tx queue and
+     * defer the skb for transmission at a later point when the
+     * current transmission is complete
+     */
+    netif_stop_queue (ndev);
+    lp->deferred_skb = new_skb;
+    /* Take the time stamp now, since we can't do this in an ISR. */
+    skb_tx_timestamp(new_skb);
+    spin_unlock_irqrestore (&lp->reset_lock, flags);
+    return 0;
+  }
+  spin_unlock_irqrestore (&lp->reset_lock, flags);
+
+  skb_tx_timestamp(new_skb);
+  ndev->stats.tx_packets++;
+  ndev->stats.tx_bytes += len;
+  dev_kfree_skb (new_skb);
+#ifdef HAVE_TRANS_START_HELPER
+  netif_trans_update(ndev);
+#else
+  ndev->trans_start = jiffies;
+#endif  
+  return 0;
+}
+
+/**
+ * s2imac_remove_ndev - Free the network device
+ * @ndev: Pointer to the network device to be freed
+ *
+ * This function un maps the IO region of the s2imac device and frees the net
+ * device.
+ */
+static void s2imac_remove_ndev (struct net_device *ndev)
+{
+  if (ndev) {
+    struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+
+    if (lp->base_addr[S2IMAC_GIGEMAP])
+    {
+      iounmap ((void __iomem __force *)(lp->base_addr[S2IMAC_GIGEMAP]));
+      lp->base_addr[S2IMAC_GIGEMAP] = NULL;
+    } 
+    if (lp->base_addr[S2IMAC_VIDEOMAP])
+    {
+      iounmap ((void __iomem __force *)(lp->base_addr[S2IMAC_VIDEOMAP]));
+      lp->base_addr[S2IMAC_VIDEOMAP] = NULL;
+    }
+      
+    if (lp->base_addr[S2IMAC_FRAMEBUFFERMAP])
+    {
+      iounmap ((void __iomem __force *)(lp->base_addr[S2IMAC_FRAMEBUFFERMAP]));
+      lp->base_addr[S2IMAC_FRAMEBUFFERMAP] = NULL;
+    }
+      
+    free_netdev (ndev);
+  }
+}
+
+#ifndef ETHTOOL_GLINKSETTINGS
+static int s2imac_ethtool_get_settings (struct net_device *ndev,
+          struct ethtool_cmd *ecmd)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+  u16 gmii_status = 0;
+
+  memset (ecmd, 0, sizeof (struct ethtool_cmd));
+
+//  if((lp->phy_type == PHY_MARVELL) || (lp->phy_type == PHY_BROADCOM)) 
+    gmii_status = s2imac_phy_read (lp, MII_BMSR);
+
+  ecmd->duplex = DUPLEX_FULL;
+
+  ecmd->supported |= SUPPORTED_MII;
+
+  ecmd->port = PORT_MII;
+
+  ecmd->speed = lp->cur_speed;
+
+  if (gmii_status & BMSR_ANEGCAPABLE) {
+    ecmd->supported |= SUPPORTED_Autoneg;
+  }
+  if (gmii_status & BMSR_ANEGCOMPLETE) {
+    ecmd->autoneg = AUTONEG_ENABLE;
+    ecmd->advertising |= ADVERTISED_Autoneg;
+  } else {
+    ecmd->autoneg = AUTONEG_DISABLE;
+  }
+  ecmd->phy_address = lp->phy_addr;
+  ecmd->transceiver = XCVR_INTERNAL;
+
+  ecmd->supported |= SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full | SUPPORTED_1000baseT_Full;
+  return 0;
+}
+
+static int s2imac_ethtool_set_settings (struct net_device *ndev,
+          struct ethtool_cmd *ecmd)
+{
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+
+  if ((ecmd->duplex != DUPLEX_FULL) ||
+      (ecmd->transceiver != XCVR_INTERNAL) ||
+      (ecmd->phy_address && (ecmd->phy_address != lp->phy_addr))) {
+    return -EOPNOTSUPP;
+  }
+
+  if ((ecmd->speed != 10000) && (ecmd->speed != 1000) && (ecmd->speed != 100) &&
+      (ecmd->speed != 10)) {
+    dev_err (&ndev->dev, "speed not supported: %d\n", ecmd->speed);
+    return -EOPNOTSUPP;
+  }
+
+  if (ecmd->speed != lp->cur_speed) {
+    lp->cur_speed = ecmd->speed;
+    dev_err (&ndev->dev, "can not change speed to: %d\n", ecmd->speed);
+  }
+  return 0;
+}
+#else
+static int s2imac_get_link_ksettings(struct net_device *dev,
+				       struct ethtool_link_ksettings *cmd)
+{
+	struct net_local *lp = (struct net_local *)netdev_priv (dev);
+  u16 gmii_status = 0;
+	u32 supported = 0;
+
+	if (!lp->init_phy)
+		return -ENODEV;
+
+  memset (cmd, 0, sizeof (struct ethtool_link_ksettings));
+
+  gmii_status = s2imac_phy_read (lp, MII_BMSR);
+
+  cmd->base.speed = lp->cur_speed;
+  cmd->base.duplex = DUPLEX_FULL;
+  cmd->base.port = PORT_MII;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 9, 212)
+	cmd->base.transceiver = XCVR_INTERNAL;
+#endif  
+  cmd->base.phy_address = lp->phy_addr;
+
+  if (gmii_status & BMSR_ANEGCOMPLETE) {
+    cmd->base.autoneg = AUTONEG_ENABLE;
+  } else {
+    cmd->base.autoneg = AUTONEG_DISABLE;
+  }
+  
+  supported |= SUPPORTED_MII;
+  if (gmii_status & BMSR_ANEGCAPABLE) {
+    supported |= SUPPORTED_Autoneg;
+  }
+  supported |= SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full | SUPPORTED_1000baseT_Full;
+	ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported,
+						supported);
+	return 0;
+}
+static int s2imac_set_link_ksettings(struct net_device *dev,
+				       const struct ethtool_link_ksettings *cmd)
+{
+	struct net_local *lp = (struct net_local *)netdev_priv (dev);
+
+	if (!lp->init_phy)
+		return -ENODEV;
+  
+	if (cmd->base.phy_address != lp->phy_addr)
+		return -EINVAL;
+  
+  if ((cmd->base.duplex != DUPLEX_FULL) ||
+      (cmd->base.transceiver != XCVR_INTERNAL) ||
+      (cmd->base.phy_address && (cmd->base.phy_address != lp->phy_addr))) {
+    return -EOPNOTSUPP;
+  }
+
+  if ((cmd->base.speed != 10000) && (cmd->base.speed != 1000) && (cmd->base.speed != 100) &&
+      (cmd->base.speed != 10)) {
+    dev_err (&dev->dev, "speed not supported: %d\n", cmd->base.speed);
+    return -EOPNOTSUPP;
+  }
+
+  if (cmd->base.speed != lp->cur_speed) {
+    lp->cur_speed = cmd->base.speed;
+    dev_err (&dev->dev, "can not change speed to: %d\n", cmd->base.speed);
+  }
+    
+	return 0;
+}
+#endif
+
+static struct net_device_ops s2imac_netdev_ops;
+
+/* From include/linux/ethtool.h */
+static struct ethtool_ops ethtool_ops = {
+#ifndef ETHTOOL_GLINKSETTINGS
+  .get_settings = s2imac_ethtool_get_settings,
+  .set_settings = s2imac_ethtool_set_settings,
+#else
+	.get_link_ksettings	= s2imac_get_link_ksettings,
+	.set_link_ksettings	= s2imac_set_link_ksettings,
+#endif  
+
+  .get_link = ethtool_op_get_link
+};
+
+/**
+ * s2imac_of_probe - Probe method for the s2imac device.
+ * @ofdev:  Pointer to OF device structure
+ * @match:  Pointer to the structure used for matching a device
+ *
+ * This function probes for the s2imac device in the device tree.
+ * It initializes the driver data structure and the hardware, sets the MAC
+ * address and registers the network device.
+ *
+ * Return:  0, if the driver is bound to the s2imac device, or
+ *    a negative error if there is failure.
+ */
+static int s2imac_of_probe(struct platform_device *ofdev)
+//static int __devinit s2imac_of_probe (struct of_device *ofdev)
+//              const struct of_device_id *match)
+{
+#ifndef CONFIG_S2IMAC_POLLING
+#ifdef CONFIG_MICROBLAZE
+  struct resource r_irq; /* Interrupt resources */
+#else  
+  struct resource *r_irq1; /* Interrupt resources */
+#endif
+#endif
+  struct resource r_mem;  /* IO mem resources */
+  struct net_device *ndev;
+  struct net_local *lp;
+//  struct device_node *np = ofdev->node;
+  struct device_node *np = ofdev->dev.of_node;
+  struct device *dev = &ofdev->dev;
+  const void *mac_address;
+  const unsigned int *clk;
+  int rc = 0;
+  u32 mac_l, mac_h;
+  int res_cnt = 0;
+  const unsigned int *cfg_int;
+  const unsigned int *phy_base_addr;
+  const unsigned int *phy_base_addr_len;
+  unsigned int phy_base_addr_len_val;
+	
+#ifdef CONFIG_MICROBLAZE
+  struct device_node *cpu;
+#endif
+
+  dev_info (dev, "probing \'%s\'\n", np->name);
+
+  /* Create an ethernet device instance */
+  ndev = alloc_etherdev (sizeof (struct net_local));
+  if (!ndev) {
+    dev_err (dev, "Could not allocate network device\n");
+    return -ENOMEM;
+  }
+
+  dev_set_drvdata (dev, ndev);
+  SET_NETDEV_DEV (ndev, dev);
+
+  lp = netdev_priv (ndev);
+  lp->ndev = ndev;
+  lp->init_phy = 0;
+  
+  lp->base_addr[S2IMAC_GIGEMAP] = NULL;
+  lp->base_addr[S2IMAC_VIDEOMAP] = NULL;
+  lp->base_addr[S2IMAC_FRAMEBUFFERMAP] = NULL;
+  
+  ndev->mem_start = 0;
+  ndev->mem_end = 0;
+  
+  lp->video_start = 0;
+  lp->video_end = 0;
+
+  lp->framebuffer_start = 0;
+  lp->framebuffer_end = 0;
+
+  lp->phy_base_addr = NULL;
+  lp->phy_base_start = 0;
+  lp->phy_base_end = 0;
+  
+  /* Get clock configuration for the device */
+  clk = of_get_property (np, "clock-frequency", NULL);
+  if (clk == NULL || (!(u32) be32_to_cpup(clk))) {
+    dev_warn (dev, "no clock-frequency property set\n");
+    rc = -ENODEV;
+
+#ifndef CONFIG_MICROBLAZE
+
+      goto error;
+
+#else /* is CONFIG_MICROBLAZE */
+    cpu = of_find_node_by_type (NULL, "cpu");
+    if (!cpu) {
+      dev_err (dev, "you don't have a cpu?\n");
+      goto error;
+    }
+
+    clk = of_get_property (cpu, "clock-frequency", NULL);
+    if (!clk) {
+      dev_err (dev, "no CPU clock-frequency property set\n");
+      goto error;
+    }
+    dev_warn (dev, "use CPU clock-frequency\n");
+    rc = 0;
+#endif
+  }
+  lp->coreclk = be32_to_cpup(clk);
+   
+  dev_info (dev, "core clock is %d Hz\n", lp->coreclk);
+  
+  cfg_int = of_get_property (np, "config-interface", NULL);
+  if (cfg_int == NULL) {
+    dev_warn (dev, "no config-interface property set, set to DEFAULT\n");
+		lp->config_interface = DEFAULT;
+	}
+	else {
+		if(strcmp( (char *)cfg_int, "DEFAULT") == 0)
+		  lp->config_interface = DEFAULT;
+		else if(strcmp( (char *)cfg_int, "XAUI") == 0)
+		  lp->config_interface = XAUI;
+		else if(strcmp( (char *)cfg_int, "RXAUI") == 0)
+		  lp->config_interface = RXAUI;
+		else if(strcmp( (char *)cfg_int, "USXGMII") == 0)
+		  lp->config_interface = USXGMII;
+		else
+		  lp->config_interface = DEFAULT;
+    dev_info (dev, "config-interface is %s [%d]\n", (char *)cfg_int, lp->config_interface);
+	}
+	
+  /* Get iospace for the gige register */
+  if(platform_get_resource_byname(ofdev, IORESOURCE_MEM, "core"))
+  {
+    rc = of_address_to_resource (ofdev->dev.of_node, S2IMAC_GIGEMAP, &r_mem);
+    if (rc) {
+      dev_err (dev, "Invalid address for core register\n");
+      goto error;
+    }
+
+    if (!request_mem_region (r_mem.start,
+          r_mem.end - r_mem.start + 1,
+          DRIVER_NAME)) {
+      dev_err (dev, "Couldn't lock core memory region at %llX\n",
+        r_mem.start);
+      rc = -EBUSY;
+      goto error;
+    }
+
+    ndev->mem_start = r_mem.start;
+    ndev->mem_end = r_mem.end;
+
+    /* Get the virtual base address for the gige register */
+    lp->base_addr[S2IMAC_GIGEMAP] =
+        ioremap (ndev->mem_start, ndev->mem_end - ndev->mem_start + 1);
+
+    if (NULL == lp->base_addr[S2IMAC_GIGEMAP]) {
+      dev_err (dev, "Could not allocate iomem for core\n");
+      rc = -EIO;
+      goto error;
+    }
+        
+    dev_info (dev, "core found at 0x%lX mapped to 0x%llX\n",
+      ndev->mem_start,
+      (uint64_t)lp->base_addr[S2IMAC_GIGEMAP]);
+  }
+  
+  /* Get iospace for the video register */
+  if(platform_get_resource_byname(ofdev, IORESOURCE_MEM, "video"))
+  {
+    rc = of_address_to_resource (ofdev->dev.of_node, S2IMAC_VIDEOMAP, &r_mem);
+    if (rc) {
+      dev_err (dev, "Invalid address for video register\n");
+      goto error;
+    }
+
+    if (!request_mem_region (r_mem.start,
+          r_mem.end - r_mem.start + 1,
+          DRIVER_NAME)) {
+      dev_err (dev, "Couldn't lock video memory region at %p\n",
+        (void *)r_mem.start);
+      rc = -EBUSY;
+      goto error;
+    }
+    lp->video_start = r_mem.start;
+    lp->video_end = r_mem.end;
+    
+    /* Get the virtual base address for the video register */
+    lp->base_addr[S2IMAC_VIDEOMAP] =
+        ioremap (lp->video_start, lp->video_end - lp->video_start + 1);
+
+    if (NULL == lp->base_addr[S2IMAC_VIDEOMAP]) {
+      dev_err (dev, "Could not allocate iomem for video\n");
+      rc = -EIO;
+      goto error;
+    }
+    
+    dev_info (dev, "video found at 0x%lX mapped to 0x%llX\n",
+      lp->video_start,
+      (uint64_t)lp->base_addr[S2IMAC_VIDEOMAP]);
+  }
+  else
+    res_cnt = 1;
+  
+#if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_ARCH_ZYNQMP)
+  /* Get iospace for the framebuffer register */
+  if(platform_get_resource_byname(ofdev, IORESOURCE_MEM, "framebuffer"))
+  {
+    rc = of_address_to_resource (ofdev->dev.of_node, S2IMAC_FRAMEBUFFERMAP - res_cnt, &r_mem);
+    if (rc) {
+      dev_err (dev, "Invalid address for framebuffer register\n");
+      goto error;
+    }
+
+    if (!request_mem_region (r_mem.start,
+          r_mem.end - r_mem.start + 1,
+          DRIVER_NAME)) {
+      dev_err (dev, "Couldn't lock framebuffer memory region at %p\n",
+        (void *)r_mem.start);
+      rc = -EBUSY;
+      goto error;
+    }
+    lp->framebuffer_start = r_mem.start;
+    lp->framebuffer_end = r_mem.end;
+    
+    /* Get the virtual base address for the framebuffer register */
+    lp->base_addr[S2IMAC_FRAMEBUFFERMAP] =
+        ioremap (lp->framebuffer_start, lp->framebuffer_end - lp->framebuffer_start + 1);
+      
+    if (NULL == lp->base_addr[S2IMAC_FRAMEBUFFERMAP]) {
+      dev_err (dev, "Could not allocate iomem for framebuffer\n");
+      rc = -EIO;
+      goto error;
+    }
+
+    dev_info (dev, "framebuffer found at 0x%lX mapped to 0x%llX\n",
+      lp->framebuffer_start,
+      (uint64_t)lp->base_addr[S2IMAC_FRAMEBUFFERMAP]);
+  }
+#endif
+
+#ifndef CONFIG_S2IMAC_POLLING
+#ifdef CONFIG_MICROBLAZE
+  /* Get IRQ for the device */
+  rc = of_irq_to_resource(ofdev->dev.of_node, 0, &r_irq);
+  if (rc == NO_IRQ) {
+    dev_err(dev, "no IRQ found\n");
+    goto error;
+  }
+  ndev->irq = r_irq.start;
+#else
+  r_irq1 = platform_get_resource(ofdev, IORESOURCE_IRQ, 0);
+  if (!r_irq1) {
+    dev_err(dev, "no IRQ found\n");
+    goto error;
+  }
+  ndev->irq = r_irq1->start;
+#endif
+  dev_info(dev,"Irq is %d\n", ndev->irq);
+#endif
+
+  spin_lock_init (&lp->reset_lock);
+
+  /* check if mac address is already set */
+  mac_h = in_be32 ((u32 *) MAC_HIGH);
+  mac_l = in_be32 ((u32 *) MAC_LOW);
+  
+  if ((mac_h == 0) && (mac_l == 0)) {
+    mac_address = of_get_mac_address (np, ndev->dev_addr);
+    if (mac_address)
+      /* Copy the MAC address from OF node. */
+      memcpy (ndev->dev_addr, mac_address, 6);
+    else
+      dev_warn (dev, "No MAC address found\n");
+
+		/* Set the MAC address in the device */
+    s2imac_update_address (lp, ndev->dev_addr);
+  } else {
+    ndev->dev_addr[0] = (u8) (mac_h >> 8);
+    ndev->dev_addr[1] = (u8) (mac_h & 0xff);
+    ndev->dev_addr[2] = (u8) (mac_l >> 24);
+    ndev->dev_addr[3] = (u8) (mac_l >> 16);
+    ndev->dev_addr[4] = (u8) (mac_l >> 8);
+    ndev->dev_addr[5] = (u8) (mac_l & 0xff);
+  }
+
+  dev_info (dev, "MAC address is now %02x:%02x:%02x:%02x:%02x:%02x\n",
+      ndev->dev_addr[0], ndev->dev_addr[1], ndev->dev_addr[2],
+      ndev->dev_addr[3], ndev->dev_addr[4], ndev->dev_addr[5]);
+  
+  /* Get phy base address length*/
+  phy_base_addr_len = of_get_property (np, "phy-base-address-length", NULL);
+  if (phy_base_addr_len == NULL) {
+    dev_warn (dev, "no phy-address-length set, set to 0\n");
+    phy_base_addr_len_val = 0;
+  }
+  else 
+    phy_base_addr_len_val = be32_to_cpup(phy_base_addr_len);
+
+  /* Get phy base address */
+  phy_base_addr = of_get_property (np, "phy-base-address", NULL);
+  if (phy_base_addr == NULL) {
+    dev_warn (dev, "no phy-base-address set, set to 0\n");
+    lp->phy_base_addr = 0;
+  }
+  else {
+    r_mem.start = be32_to_cpup(phy_base_addr);
+    if(r_mem.start)
+    {
+      r_mem.end = r_mem.start + (phy_base_addr_len_val - 1);
+      
+      if (!request_mem_region (r_mem.start,
+            r_mem.end - r_mem.start + 1,
+            DRIVER_NAME)) {
+        dev_err (dev, "Couldn't lock phy base address region at %p\n",
+          (void *)r_mem.start);
+        rc = -EBUSY;
+        goto error;
+      }
+      
+      lp->phy_base_start = r_mem.start;
+      lp->phy_base_end = r_mem.end;
+
+      /* Get the virtual base address for the phy base address */
+      lp->phy_base_addr = ioremap (lp->phy_base_start, lp->phy_base_end - lp->phy_base_start + 1);
+
+      if (NULL == lp->phy_base_addr) {
+        dev_err (dev, "Could not allocate iomem for phy base address\n");
+        rc = -EIO;
+        goto error;
+      }
+          
+      dev_info (dev, "phy base address found at 0x%lX mapped to 0x%llX\n",
+        lp->phy_base_start,
+        (uint64_t)lp->phy_base_addr);
+    }
+  }
+  
+  /* Scan to find the PHY */
+  phy_setup (lp, ndev);
+  lp->phy_addr = detect_phy (lp, dev);
+  if(lp->phy_addr == -1)
+    goto error;
+
+#ifdef CONFIG_S2IMAC_POLLING
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(4, 15, 0)) 
+  init_timer (&lp->irq_timer);
+  lp->irq_timer.function = s2imac_irq_timer;
+  lp->irq_timer.data = (unsigned long)ndev;
+#else
+   timer_setup(&lp->irq_timer, s2imac_irq_timer, 0);
+#endif
+#endif
+
+  ndev->netdev_ops = &s2imac_netdev_ops;
+  ndev->flags &= ~IFF_MULTICAST;
+  ndev->watchdog_timeo = TX_TIMEOUT;
+  ndev->ethtool_ops = &ethtool_ops;
+
+  /* Set ethtool IOCTL handler vectors. */
+//  SET_ETHTOOL_OPS (ndev, &ethtool_ops);
+
+  /* Finally, register the device */
+  rc = register_netdev (ndev);
+  if (rc) {
+    dev_err (dev, "Cannot register network device, aborting\n");
+    goto error;
+  }
+  
+  return 0;
+
+error:
+
+  if(lp->base_addr[S2IMAC_FRAMEBUFFERMAP])
+  {
+    iounmap (lp->base_addr[S2IMAC_FRAMEBUFFERMAP]);
+    lp->base_addr[S2IMAC_FRAMEBUFFERMAP] = NULL;
+  }
+  
+  if(lp->base_addr[S2IMAC_VIDEOMAP])
+  {
+    iounmap (lp->base_addr[S2IMAC_VIDEOMAP]);
+    lp->base_addr[S2IMAC_VIDEOMAP] = NULL;
+  }
+  
+  if(lp->base_addr[S2IMAC_GIGEMAP])
+  {
+    iounmap (lp->base_addr[S2IMAC_GIGEMAP]);
+    lp->base_addr[S2IMAC_GIGEMAP] = NULL;
+  }
+  
+  if(lp->framebuffer_start)
+  {
+    release_mem_region (lp->framebuffer_start,
+            lp->framebuffer_end - lp->framebuffer_start + 1);
+    lp->framebuffer_start = 0;
+  }
+  
+  if(lp->video_start)
+  {
+    release_mem_region (lp->video_start,
+            lp->video_end - lp->video_start + 1);
+    lp->video_start = 0;
+  }
+  
+  if(ndev->mem_start)
+  {
+    release_mem_region (ndev->mem_start,
+            ndev->mem_end - ndev->mem_start + 1);
+    ndev->mem_start = 0;
+  } 
+
+  if(lp->phy_base_start)
+  {
+    release_mem_region (lp->phy_base_start,
+            lp->phy_base_end - lp->phy_base_start + 1);
+    lp->phy_base_start = 0;
+  }
+  
+  s2imac_remove_ndev (ndev);
+  
+  return rc;
+}
+
+/**
+ * s2imac_of_remove - Unbind the driver from the s2imac device.
+ * @of_dev: Pointer to OF device structure
+ *
+ * This function is called if a device is physically removed from the system or
+ * if the driver module is being unloaded. It frees any resources allocated to
+ * the device.
+ *
+ * Return:  0, always.
+ */
+//static int __devexit s2imac_of_remove (struct of_device *of_dev)
+static int s2imac_of_remove (struct platform_device *of_dev)
+{
+  struct device *dev = &of_dev->dev;
+  struct net_device *ndev = dev_get_drvdata (dev);
+  struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+
+  unregister_netdev (ndev);
+
+  s2imac_remove_ndev (ndev);
+
+  if(lp->framebuffer_start)
+  {
+    release_mem_region (lp->framebuffer_start,
+            lp->framebuffer_end - lp->framebuffer_start + 1);
+    lp->framebuffer_start = 0;
+  }
+  
+  if(lp->video_start)
+  {
+    release_mem_region (lp->video_start,
+            lp->video_end - lp->video_start + 1);
+    lp->video_start = 0;
+  }
+  
+  if(ndev->mem_start)
+  {
+    release_mem_region (ndev->mem_start,
+            ndev->mem_end - ndev->mem_start + 1);
+    ndev->mem_start = 0;
+  }
+
+  if(lp->phy_base_start)
+  {
+    release_mem_region (lp->phy_base_start,
+            lp->phy_base_end - lp->phy_base_start + 1);
+    lp->phy_base_start = 0;
+  }
+  
+  dev_set_drvdata (dev, NULL);
+
+  return 0;
+}
+
+static int s2imac_change_mtu (struct net_device *ndev, int new_mtu)
+{
+  int device_enable = 0;
+#ifdef CONFIG_XILINX_GIGE_VLAN
+  int head_size = XTE_HDR_VLAN_SIZE;
+#else
+  int head_size = XTE_HDR_SIZE;
+#endif
+  int max_frame = new_mtu + head_size + XTE_TRL_SIZE;
+  int min_frame = 1 + head_size + XTE_TRL_SIZE;
+
+  if (max_frame < min_frame)
+    return -EINVAL;
+
+  if (max_frame > XTE_MAX_FRAME_SIZE) {
+    dev_info (&ndev->dev, "Wrong MTU packet size. Use %d size\n",
+      XTE_MTU);
+    new_mtu = XTE_MTU;
+  }
+
+  ndev->mtu = new_mtu;  /* change mtu in net_device structure */
+
+  /* stop driver */
+  if (netif_running (ndev)) {
+    device_enable = 1;
+    s2imac_close (ndev);
+  }
+
+  if (device_enable)
+    s2imac_open (ndev); /* open the device */
+  return 0;
+}
+
+static int s2imac_ioctl (struct net_device *ndev, struct ifreq *rq, void __user *data, int cmd)
+{
+	struct net_local *lp = (struct net_local *)netdev_priv (ndev);
+	s2igen_content_t *gen_content;
+	int ret = 0;
+
+	gen_content = kmalloc(sizeof(s2igen_content_t), GFP_KERNEL);
+	if (!gen_content)
+		return -ENOMEM;
+
+	ret = copy_from_user (gen_content, data, sizeof (s2igen_content_t));
+	if (ret) {
+		printk(KERN_ERR "copy_from_user fails ret = %d", ret);
+		printk(KERN_ERR "gen_content address = %u data = %u\n", gen_content->address, gen_content->data);
+		kfree(gen_content);
+	    return -EFAULT;
+	}
+
+  /* check address range 1st slot --> device base address */
+  if((cmd == SIOS2IGENRD) || (cmd == SIOS2IGENWR)){
+    if (gen_content->address > (ndev->mem_end - ndev->mem_start + 1))
+	{
+		printk(KERN_ERR "gen_content->address failed");
+		kfree(gen_content);
+		return -EINVAL;
+	}
+  }
+
+  /* check address range 2st slot --> register base address */
+  if((cmd == SIOS2IVIDEORD) || (cmd == SIOS2IVIDEOWR)){
+
+    if (gen_content->address > (lp->video_end - lp->video_start + 1)) {
+		kfree(gen_content);
+		return -EINVAL;
+	}
+  }
+  
+  /* check address range 3st slot --> register base address */
+  if((cmd == SIOS2IFBUFRD) || (cmd == SIOS2IFBUFWR)){
+
+    if (gen_content->address > (lp->framebuffer_end - lp->framebuffer_start + 1)) {
+		kfree(gen_content);
+		return -EINVAL;
+	}
+  }
+
+  switch (cmd) {
+  case SIOS2IGENRD: /* core read */
+
+    gen_content->data =
+        in_be32 ((u32 *) (lp->base_addr[S2IMAC_GIGEMAP] + gen_content->address));
+
+	ret = copy_to_user(data, gen_content, sizeof (s2igen_content_t));
+    if (ret) {
+		printk(KERN_ERR "copy_to_user failed ret = %d", ret);
+		kfree(gen_content);
+		return -EFAULT;
+	}
+	break;
+
+  case SIOS2IGENWR: /* core write */
+
+    out_be32 ((u32 *) (lp->base_addr[S2IMAC_GIGEMAP] + gen_content->address),
+        gen_content->data);
+	break;
+
+  case SIOS2IVIDEORD: /* video register read */
+
+    gen_content->data =
+        in_be32 ((u32 *) (lp->base_addr[S2IMAC_VIDEOMAP] + gen_content->address));
+
+    if (copy_to_user
+        (data, gen_content, sizeof (s2igen_content_t))) {
+		kfree(gen_content);
+		return -EFAULT;
+	}
+	break;
+
+  case SIOS2IVIDEOWR: /* video register write */
+
+    out_be32 ((u32 *) (lp->base_addr[S2IMAC_VIDEOMAP] + gen_content->address),
+        gen_content->data);
+	break;
+
+  case SIOS2IFBUFRD: /* framebuffer register read */
+
+    gen_content->data =
+        in_be32 ((u32 *) (lp->base_addr[S2IMAC_FRAMEBUFFERMAP] + gen_content->address));
+
+    if (copy_to_user
+        (data, gen_content, sizeof (s2igen_content_t))) {
+		kfree(gen_content);
+		return -EFAULT;
+	}
+	break;
+
+  case SIOS2IFBUFWR: /* framebuffer register write */
+
+    out_be32 ((u32 *) (lp->base_addr[S2IMAC_FRAMEBUFFERMAP] + gen_content->address),
+        gen_content->data);
+	break;
+
+  default:
+	kfree(gen_content);
+    return -EOPNOTSUPP;
+  }
+	kfree(gen_content);
+	return 0;
+}
+
+/**
+ * s2imac_set_rx_mode - enable/disable promiscuous and multicast modes
+ * @ndev: network interface device structure
+ */
+static void s2imac_set_rx_mode(struct net_device *ndev)
+{
+  struct net_local *lp = netdev_priv(ndev);
+  u32 reg;
+
+  /* get promiscuous mode of the MAC */
+  reg = in_be32 ((u32 *) AFM);
+  
+  /* Enable multicast mode */
+  if ((ndev->flags & IFF_ALLMULTI) || (ndev->flags & IFF_MULTICAST)){
+    reg |= 0x80000000;
+  /* Disable multicast mode */
+  } else {
+    reg = ~0x80000000;
+  }
+
+  /* enable/disable promiscuous mode of the MAC */
+  out_be32 ((u32 *) AFM, reg);
+}
+
+static struct net_device_ops s2imac_netdev_ops = {
+  .ndo_open = s2imac_open,
+  .ndo_stop = s2imac_close,
+  .ndo_start_xmit = s2imac_send,
+  .ndo_siocdevprivate = s2imac_ioctl,
+  .ndo_change_mtu = s2imac_change_mtu,
+  .ndo_set_mac_address = s2imac_set_mac_address,
+  .ndo_tx_timeout = s2imac_tx_timeout,
+  .ndo_get_stats = s2imac_get_stats,
+  .ndo_set_rx_mode  = s2imac_set_rx_mode,
+};
+
+/* Match table for OF platform binding */
+//static struct of_device_id s2imac_of_match[] __devinitdata = {
+static struct of_device_id s2imac_of_match[] = {
+  { .compatible = "s2i,s2imac-1.00.a", },
+  { .compatible = "xlnx,s2imac-epc-1.02.a", },
+  { .compatible = "xlnx,s2imac-epc-2.0", },
+  { .compatible = "s2i,s2imac-epc", .type = "network", },
+  { /* end of list */ },
+};
+
+MODULE_DEVICE_TABLE (of, s2imac_of_match);
+
+//static struct of_platform_driver s2imac_of_driver = {
+static struct platform_driver s2imac_of_driver = {
+  .driver = {
+    .name = DRIVER_NAME,
+    .owner = THIS_MODULE,
+    .of_match_table = s2imac_of_match,
+  },
+  .probe = s2imac_of_probe,
+  .remove = s2imac_of_remove,
+};
+
+/**
+ * s2imac_init - Initial driver registration call
+ *
+ * Return:  0 upon success, or a negative error upon failure.
+ */
+static int __init s2imac_init (void)
+{
+  /* No kernel boot options used, we just need to register the driver */
+//  return of_register_platform_driver (&s2imac_of_driver);
+
+  pr_info("S2I Ethernet MAC Driver - %s\n",
+    DRIVER_VERS);
+  pr_info("Copyright(c) 2010 - 2021 Sensor to Image GmbH.\n");
+  
+  return platform_driver_register (&s2imac_of_driver);
+}
+
+/**
+ * s2imac_cleanup - Driver un-registration call
+ */
+static void __exit s2imac_cleanup (void)
+{
+//  of_unregister_platform_driver (&s2imac_of_driver);
+  platform_driver_unregister (&s2imac_of_driver);
+}
+
+module_init (s2imac_init);
+module_exit (s2imac_cleanup);
+
+MODULE_AUTHOR ("Sensor to Image GmbH.");
+MODULE_DESCRIPTION ("S2I Ethernet MAC Driver");
+MODULE_LICENSE ("GPL");
+MODULE_AUTHOR("Enclustra");
+//MODULE_VERSION("1.0");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-sensor-module/LICENSE.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-sensor-module/LICENSE.md
@@ -0,0 +1,342 @@
+		    GNU GENERAL PUBLIC LICENSE
+		       Version 2, June 1991
+
+ Copyright (C) 1989, 1991 Free Software Foundation, Inc.
+                       51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+			    Preamble
+
+  The licenses for most software are designed to take away your
+freedom to share and change it.  By contrast, the GNU General Public
+License is intended to guarantee your freedom to share and change free
+software--to make sure the software is free for all its users.  This
+General Public License applies to most of the Free Software
+Foundation's software and to any other program whose authors commit to
+using it.  (Some other Free Software Foundation software is covered by
+the GNU Library General Public License instead.)  You can apply it to
+your programs, too.
+
+  When we speak of free software, we are referring to freedom, not
+price.  Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+this service if you wish), that you receive source code or can get it
+if you want it, that you can change the software or use pieces of it
+in new free programs; and that you know you can do these things.
+
+  To protect your rights, we need to make restrictions that forbid
+anyone to deny you these rights or to ask you to surrender the rights.
+These restrictions translate to certain responsibilities for you if you
+distribute copies of the software, or if you modify it.
+
+  For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must give the recipients all the rights that
+you have.  You must make sure that they, too, receive or can get the
+source code.  And you must show them these terms so they know their
+rights.
+
+  We protect your rights with two steps: (1) copyright the software, and
+(2) offer you this license which gives you legal permission to copy,
+distribute and/or modify the software.
+
+  Also, for each author's protection and ours, we want to make certain
+that everyone understands that there is no warranty for this free
+software.  If the software is modified by someone else and passed on, we
+want its recipients to know that what they have is not the original, so
+that any problems introduced by others will not reflect on the original
+authors' reputations.
+
+  Finally, any free program is threatened constantly by software
+patents.  We wish to avoid the danger that redistributors of a free
+program will individually obtain patent licenses, in effect making the
+program proprietary.  To prevent this, we have made it clear that any
+patent must be licensed for everyone's free use or not licensed at all.
+
+  The precise terms and conditions for copying, distribution and
+modification follow.
+
+		    GNU GENERAL PUBLIC LICENSE
+   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
+
+  0. This License applies to any program or other work which contains
+a notice placed by the copyright holder saying it may be distributed
+under the terms of this General Public License.  The "Program", below,
+refers to any such program or work, and a "work based on the Program"
+means either the Program or any derivative work under copyright law:
+that is to say, a work containing the Program or a portion of it,
+either verbatim or with modifications and/or translated into another
+language.  (Hereinafter, translation is included without limitation in
+the term "modification".)  Each licensee is addressed as "you".
+
+Activities other than copying, distribution and modification are not
+covered by this License; they are outside its scope.  The act of
+running the Program is not restricted, and the output from the Program
+is covered only if its contents constitute a work based on the
+Program (independent of having been made by running the Program).
+Whether that is true depends on what the Program does.
+
+  1. You may copy and distribute verbatim copies of the Program's
+source code as you receive it, in any medium, provided that you
+conspicuously and appropriately publish on each copy an appropriate
+copyright notice and disclaimer of warranty; keep intact all the
+notices that refer to this License and to the absence of any warranty;
+and give any other recipients of the Program a copy of this License
+along with the Program.
+
+You may charge a fee for the physical act of transferring a copy, and
+you may at your option offer warranty protection in exchange for a fee.
+
+  2. You may modify your copy or copies of the Program or any portion
+of it, thus forming a work based on the Program, and copy and
+distribute such modifications or work under the terms of Section 1
+above, provided that you also meet all of these conditions:
+
+    a) You must cause the modified files to carry prominent notices
+    stating that you changed the files and the date of any change.
+
+    b) You must cause any work that you distribute or publish, that in
+    whole or in part contains or is derived from the Program or any
+    part thereof, to be licensed as a whole at no charge to all third
+    parties under the terms of this License.
+
+    c) If the modified program normally reads commands interactively
+    when run, you must cause it, when started running for such
+    interactive use in the most ordinary way, to print or display an
+    announcement including an appropriate copyright notice and a
+    notice that there is no warranty (or else, saying that you provide
+    a warranty) and that users may redistribute the program under
+    these conditions, and telling the user how to view a copy of this
+    License.  (Exception: if the Program itself is interactive but
+    does not normally print such an announcement, your work based on
+    the Program is not required to print an announcement.)
+
+These requirements apply to the modified work as a whole.  If
+identifiable sections of that work are not derived from the Program,
+and can be reasonably considered independent and separate works in
+themselves, then this License, and its terms, do not apply to those
+sections when you distribute them as separate works.  But when you
+distribute the same sections as part of a whole which is a work based
+on the Program, the distribution of the whole must be on the terms of
+this License, whose permissions for other licensees extend to the
+entire whole, and thus to each and every part regardless of who wrote it.
+
+Thus, it is not the intent of this section to claim rights or contest
+your rights to work written entirely by you; rather, the intent is to
+exercise the right to control the distribution of derivative or
+collective works based on the Program.
+
+In addition, mere aggregation of another work not based on the Program
+with the Program (or with a work based on the Program) on a volume of
+a storage or distribution medium does not bring the other work under
+the scope of this License.
+
+  3. You may copy and distribute the Program (or a work based on it,
+under Section 2) in object code or executable form under the terms of
+Sections 1 and 2 above provided that you also do one of the following:
+
+    a) Accompany it with the complete corresponding machine-readable
+    source code, which must be distributed under the terms of Sections
+    1 and 2 above on a medium customarily used for software interchange; or,
+
+    b) Accompany it with a written offer, valid for at least three
+    years, to give any third party, for a charge no more than your
+    cost of physically performing source distribution, a complete
+    machine-readable copy of the corresponding source code, to be
+    distributed under the terms of Sections 1 and 2 above on a medium
+    customarily used for software interchange; or,
+
+    c) Accompany it with the information you received as to the offer
+    to distribute corresponding source code.  (This alternative is
+    allowed only for noncommercial distribution and only if you
+    received the program in object code or executable form with such
+    an offer, in accord with Subsection b above.)
+
+The source code for a work means the preferred form of the work for
+making modifications to it.  For an executable work, complete source
+code means all the source code for all modules it contains, plus any
+associated interface definition files, plus the scripts used to
+control compilation and installation of the executable.  However, as a
+special exception, the source code distributed need not include
+anything that is normally distributed (in either source or binary
+form) with the major components (compiler, kernel, and so on) of the
+operating system on which the executable runs, unless that component
+itself accompanies the executable.
+
+If distribution of executable or object code is made by offering
+access to copy from a designated place, then offering equivalent
+access to copy the source code from the same place counts as
+distribution of the source code, even though third parties are not
+compelled to copy the source along with the object code.
+
+  4. You may not copy, modify, sublicense, or distribute the Program
+except as expressly provided under this License.  Any attempt
+otherwise to copy, modify, sublicense or distribute the Program is
+void, and will automatically terminate your rights under this License.
+However, parties who have received copies, or rights, from you under
+this License will not have their licenses terminated so long as such
+parties remain in full compliance.
+
+  5. You are not required to accept this License, since you have not
+signed it.  However, nothing else grants you permission to modify or
+distribute the Program or its derivative works.  These actions are
+prohibited by law if you do not accept this License.  Therefore, by
+modifying or distributing the Program (or any work based on the
+Program), you indicate your acceptance of this License to do so, and
+all its terms and conditions for copying, distributing or modifying
+the Program or works based on it.
+
+  6. Each time you redistribute the Program (or any work based on the
+Program), the recipient automatically receives a license from the
+original licensor to copy, distribute or modify the Program subject to
+these terms and conditions.  You may not impose any further
+restrictions on the recipients' exercise of the rights granted herein.
+You are not responsible for enforcing compliance by third parties to
+this License.
+
+  7. If, as a consequence of a court judgment or allegation of patent
+infringement or for any other reason (not limited to patent issues),
+conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License.  If you cannot
+distribute so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you
+may not distribute the Program at all.  For example, if a patent
+license would not permit royalty-free redistribution of the Program by
+all those who receive copies directly or indirectly through you, then
+the only way you could satisfy both it and this License would be to
+refrain entirely from distribution of the Program.
+
+If any portion of this section is held invalid or unenforceable under
+any particular circumstance, the balance of the section is intended to
+apply and the section as a whole is intended to apply in other
+circumstances.
+
+It is not the purpose of this section to induce you to infringe any
+patents or other property right claims or to contest validity of any
+such claims; this section has the sole purpose of protecting the
+integrity of the free software distribution system, which is
+implemented by public license practices.  Many people have made
+generous contributions to the wide range of software distributed
+through that system in reliance on consistent application of that
+system; it is up to the author/donor to decide if he or she is willing
+to distribute software through any other system and a licensee cannot
+impose that choice.
+
+This section is intended to make thoroughly clear what is believed to
+be a consequence of the rest of this License.
+
+  8. If the distribution and/or use of the Program is restricted in
+certain countries either by patents or by copyrighted interfaces, the
+original copyright holder who places the Program under this License
+may add an explicit geographical distribution limitation excluding
+those countries, so that distribution is permitted only in or among
+countries not thus excluded.  In such case, this License incorporates
+the limitation as if written in the body of this License.
+
+  9. The Free Software Foundation may publish revised and/or new versions
+of the General Public License from time to time.  Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+Each version is given a distinguishing version number.  If the Program
+specifies a version number of this License which applies to it and "any
+later version", you have the option of following the terms and conditions
+either of that version or of any later version published by the Free
+Software Foundation.  If the Program does not specify a version number of
+this License, you may choose any version ever published by the Free Software
+Foundation.
+
+  10. If you wish to incorporate parts of the Program into other free
+programs whose distribution conditions are different, write to the author
+to ask for permission.  For software which is copyrighted by the Free
+Software Foundation, write to the Free Software Foundation; we sometimes
+make exceptions for this.  Our decision will be guided by the two goals
+of preserving the free status of all derivatives of our free software and
+of promoting the sharing and reuse of software generally.
+
+			    NO WARRANTY
+
+  11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
+FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.  EXCEPT WHEN
+OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
+PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
+OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRE RISK AS
+TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.  SHOULD THE
+PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
+REPAIR OR CORRECTION.
+
+  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
+REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
+INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
+OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
+TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
+YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
+PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGES.
+
+		     END OF TERMS AND CONDITIONS
+
+	    How to Apply These Terms to Your New Programs
+
+  If you develop a new program, and you want it to be of the greatest
+possible use to the public, the best way to achieve this is to make it
+free software which everyone can redistribute and change under these terms.
+
+  To do so, attach the following notices to the program.  It is safest
+to attach them to the start of each source file to most effectively
+convey the exclusion of warranty; and each file should have at least
+the "copyright" line and a pointer to where the full notice is found.
+
+    <one line to give the program's name and a brief idea of what it does.>
+    Copyright (C) <year>  <name of author>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+Also add information on how to contact you by electronic and paper mail.
+
+If the program is interactive, make it output a short notice like this
+when it starts in an interactive mode:
+
+    Gnomovision version 69, Copyright (C) year name of author
+    Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
+    This is free software, and you are welcome to redistribute it
+    under certain conditions; type `show c' for details.
+
+The hypothetical commands `show w' and `show c' should show the appropriate
+parts of the General Public License.  Of course, the commands you use may
+be called something other than `show w' and `show c'; they could even be
+mouse-clicks or menu items--whatever suits your program.
+
+You should also get your employer (if you work as a programmer) or your
+school, if any, to sign a "copyright disclaimer" for the program, if
+necessary.  Here is a sample; alter the names:
+
+  Yoyodyne, Inc., hereby disclaims all copyright interest in the program
+  `Gnomovision' (which makes passes at compilers) written by James Hacker.
+
+  <signature of Ty Coon>, 1 April 1989
+  Ty Coon, President of Vice
+
+This General Public License does not permit incorporating your program into
+proprietary programs.  If your program is a subroutine library, you may
+consider it more useful to permit linking proprietary applications with the
+library.  If this is what you want to do, use the GNU Library General
+Public License instead of this License.
+
+Copyright (C) 2022 FRAMOS.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-sensor-module/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-sensor-module/Makefile
@@ -0,0 +1,38 @@
+#
+# Copyright (c) 2022. FRAMOS.  All rights reserved.
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms and conditions of the GNU General Public License,
+# version 2, as published by the Free Software Foundation.
+#
+# This program is distributed in the hope it will be useful, but WITHOUT
+# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+# FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+# more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+#
+
+obj-m := imx547.o
+
+SRC := $(shell pwd)
+
+EXTRA_CFLAGS := -I$(KERNEL_SRC)/drivers/media/platform/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/include/linux
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/generated/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/generated/uapi/
+EXTRA_CFLAGS += -I$(KERNEL_SRC)/arch/arm64/include/uapi/
+
+all:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules
+
+modules_install:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules_install
+
+clean:
+	rm -f *.o *~ core .depend .*.cmd *.ko *.mod.c
+	rm -f Module.markers Module.symvers modules.order
+	rm -f */modules.order */modules.builtin
+	rm -rf .tmp_versions Modules.symvers
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-sensor-module/README.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-sensor-module/README.md
@@ -0,0 +1,7 @@
+/******************************************************************************
+* Copyright (C) 2010 - 2022 Xilinx, Inc. All rights reserved.
+*******************************************************************************/
+# mv-camera-sensor-module
+IMX547 sensor device driver
+
+mv-camera defect detection application is using IMX547 sensor to capture the live frames. This V4L2 based device driver will configure imx547 sensor & exposes user controls to tune gain, exposure, black_level etc.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-sensor-module/imx547.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-sensor-module/imx547.c
@@ -0,0 +1,1168 @@
+/*
+ * imx547.c - imx547 sensor driver
+ *
+ * Copyright (c) 2022. FRAMOS.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/v4l2-mediabus.h>
+#include <linux/videodev2.h>
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+
+#include "imx547_mode_tbls.h"
+
+#define IMX547_K_FACTOR 1000LL
+#define IMX547_M_FACTOR 1000000LL
+#define IMX547_G_FACTOR 1000000000LL
+#define IMX547_T_FACTOR 1000000000000LL
+
+#define IMX547_MIN_GAIN             (0)
+#define IMX547_MAX_GAIN             (480)
+#define IMX547_DEF_GAIN             (0)
+
+#define IMX547_MIN_BLACK_LEVEL          (0)
+#define IMX547_MAX_BLACK_LEVEL_10BIT    (1023)
+#define IMX547_MAX_BLACK_LEVEL_12BIT    (4095)
+#define IMX547_DEF_BLACK_LEVEL_10BIT    (60)
+#define IMX547_DEF_BLACK_LEVEL_12BIT    (240)
+
+#define IMX547_MIN_EXPOSURE_TIME    (14)
+#define IMX547_MAX_EXPOSURE_TIME    (660000)
+#define IMX547_DEF_EXPOSURE_TIME    (1000)
+
+// 10bit maximum 122.2 fps
+#define IMX547_MAX_FRAME_INTERVAL_10BIT_NUMERATOR   (5)
+#define IMX547_MAX_FRAME_INTERVAL_10BIT_DENOMINATOR (611)
+// 12bit maximum 82.4 fps
+#define IMX547_MAX_FRAME_INTERVAL_12BIT_NUMERATOR   (5)
+#define IMX547_MAX_FRAME_INTERVAL_12BIT_DENOMINATOR (412)
+#define IMX547_MIN_FRAME_RATE       (2)
+#define IMX547_DEF_FRAME_RATE       (60)
+
+#define IMX547_MIN_SHS_LENGTH_10BIT 54
+#define IMX547_MIN_SHS_LENGTH_12BIT 40
+
+#define IMX547_DEFAULT_LINE_TIME_10BIT 3700 // [ns]
+#define IMX547_DEFAULT_LINE_TIME_12BIT 5500 // [ns]
+
+#define IMX547_INCK 74250000LL
+
+static const struct of_device_id imx547_of_match[] = {
+    { .compatible = "framos,imx547" },
+    { }
+};
+MODULE_DEVICE_TABLE(of, imx547_of_match);
+
+static const struct regmap_config imx547_regmap_config = {
+    .reg_bits = 16,
+    .val_bits = 8,
+    .cache_type = REGCACHE_RBTREE,
+};
+
+/*
+ * imx547 test pattern related structure
+ */
+enum {
+    TEST_PATTERN_NO_PATTERN = 0,
+    TEST_PATTERN_SEQUENCE_PATTERN_1,
+    TEST_PATTERN_SEQUENCE_PATTERN_2,
+    TEST_PATTERN_GRADIATION_PATTERN,
+};
+
+static const char * const tp_qmenu[] = {
+    "No Pattern",
+    "Sequence Pattern 1",
+    "Sequence Pattern 2",
+    "Gradiation Pattern",
+};
+
+/*
+ * struct imx547_ctrls - imx547 ctrl structure
+ * @handler: V4L2 ctrl handler structure
+ * @exposure: Pointer to exposure ctrl structure
+ * @gain: Pointer to gain ctrl structure
+ * @test_pattern: Pointer to test pattern ctrl structure
+ * @black_level: Pointer to black level ctrl structure
+ */
+struct imx547_ctrls {
+    struct v4l2_ctrl_handler handler;
+    struct v4l2_ctrl *exposure;
+    struct v4l2_ctrl *gain;
+    struct v4l2_ctrl *test_pattern;
+    struct v4l2_ctrl *black_level;
+};
+
+/*
+ * struct stim547 - imx547 device structure
+ * @sd: V4L2 subdevice structure
+ * @pad: Media pad structure
+ * @client: Pointer to I2C client
+ * @ctrls: imx547 control structure
+ * @format: V4L2 media bus frame format structure
+ * @frame_interval: V4L2 frame interval structure
+ * @regmap: Pointer to regmap structure
+ * @gt_trx_reset_gpio: Pointer to GT TRX wizard reset gpio
+ * @pipe_reset_gpio: Pointer to input pipe reset gpio
+ * @lock: Mutex structure
+ * @frame_length: Frame length
+ * @line_time: Line time in nanoseconds
+ */
+struct stimx547 {
+    struct v4l2_subdev sd;
+    struct media_pad pad;
+    struct i2c_client *client;
+    struct imx547_ctrls ctrls;
+    struct v4l2_mbus_framefmt format;
+    struct v4l2_fract frame_interval;
+    struct regmap *regmap;
+    struct gpio_desc *gt_trx_reset_gpio;
+    struct gpio_desc *pipe_reset_gpio;
+    struct mutex lock; /* mutex lock for operations */
+    u64 frame_length;
+    u32 line_time;
+};
+
+/*
+ * Function declaration
+ */
+static int imx547_set_gain(struct stimx547 *priv, int val);
+static int imx547_set_exposure(struct stimx547 *priv, int val);
+static int imx547_set_test_pattern(struct stimx547 *priv, int val);
+static int imx547_set_black_level(struct stimx547 *priv, int val);
+static int imx547_set_frame_interval(struct stimx547 *priv);
+static int imx547_calculate_line_time(struct stimx547 *priv);
+
+static inline void msleep_range(unsigned int delay_base)
+{
+    usleep_range(delay_base * 1000, delay_base * 1000 + 500);
+}
+
+/*
+ * v4l2_ctrl and v4l2_subdev related operations
+ */
+static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
+{
+    return &container_of(ctrl->handler,
+                 struct stimx547, ctrls.handler)->sd;
+}
+
+static inline struct stimx547 *to_imx547(struct v4l2_subdev *sd)
+{
+    return container_of(sd, struct stimx547, sd);
+}
+
+/*
+ * Writing a register table
+ *
+ * @priv: Pointer to device
+ * @table: Table containing register values (with optional delays)
+ *
+ * This is used to write register table into sensor's reg map.
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_write_table(struct stimx547 *priv, const struct reg_8 table[])
+{
+    struct regmap *regmap = priv->regmap;
+    int err = 0;
+    const struct reg_8 *next;
+    u8 val;
+
+    int range_start = -1;
+    int range_count = 0;
+    u8 range_vals[16];
+    int max_range_vals = ARRAY_SIZE(range_vals);
+
+    for (next = table;; next++) {
+        if ((next->addr != range_start + range_count) ||
+            (next->addr == IMX547_TABLE_END) ||
+            (next->addr == IMX547_TABLE_WAIT_MS) ||
+            (range_count == max_range_vals)) {
+            if (range_count == 1)
+                err = regmap_write(regmap,
+                           range_start, range_vals[0]);
+            else if (range_count > 1)
+                err = regmap_bulk_write(regmap, range_start,
+                            &range_vals[0],
+                            range_count);
+            else
+                err = 0;
+
+            if (err)
+                return err;
+
+            range_start = -1;
+            range_count = 0;
+
+            /* Handle special address values */
+            if (next->addr == IMX547_TABLE_END)
+                break;
+
+            if (next->addr == IMX547_TABLE_WAIT_MS) {
+                msleep_range(next->val);
+                continue;
+            }
+        }
+
+        val = next->val;
+
+        if (range_start == -1)
+            range_start = next->addr;
+
+        range_vals[range_count++] = val;
+    }
+    return 0;
+}
+
+static inline int imx547_write_reg(struct stimx547 *priv, u16 addr, u8 val)
+{
+    int err;
+
+    err = regmap_write(priv->regmap, addr, val);
+    if (err)
+        dev_err(&priv->client->dev,
+            "%s : i2c write failed, %x = %x\n", __func__,
+            addr, val);
+    else
+        dev_dbg(&priv->client->dev,
+            "%s : addr 0x%x, val=0x%x\n", __func__,
+            addr, val);
+    return err;
+}
+
+/**
+ * Read a multibyte register.
+ *
+ * Uses a bulk read where possible.
+ *
+ * @priv: Pointer to device structure
+ * @addr: Address of the LSB register.  Other registers must be
+ *        consecutive, least-to-most significant.
+ * @val: Pointer to store the register value (cpu endianness)
+ * @nbytes: Number of bytes to read (range: [1..3]).
+ *          Other bytes are zet to 0.
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_read_mbreg(struct stimx547 *priv, u16 addr, u32 *val,
+                 size_t nbytes)
+{
+    __le32 val_le = 0;
+    int err;
+
+    err = regmap_bulk_read(priv->regmap, addr, &val_le, nbytes);
+    if (err) {
+        dev_err(&priv->client->dev,
+            "%s : i2c bulk read failed, %x (%zu bytes)\n",
+            __func__, addr, nbytes);
+    } else {
+        *val = le32_to_cpu(val_le);
+        dev_dbg(&priv->client->dev,
+            "%s : addr 0x%x, val=0x%x (%zu bytes)\n",
+            __func__, addr, *val, nbytes);
+    }
+
+    return err;
+}
+
+/**
+ * Write a multibyte register.
+ *
+ * Uses a bulk write where possible.
+ *
+ * @priv: Pointer to device structure
+ * @addr: Address of the LSB register.  Other registers must be
+ *        consecutive, least-to-most significant.
+ * @val: Value to be written to the register (cpu endianness)
+ * @nbytes: Number of bytes to write (range: [1..3])
+ */
+static int imx547_write_mbreg(struct stimx547 *priv, u16 addr, u32 val,
+                  size_t nbytes)
+{
+    __le32 val_le = cpu_to_le32(val);
+    int err;
+
+    err = regmap_bulk_write(priv->regmap, addr, &val_le, nbytes);
+    if (err)
+        dev_err(&priv->client->dev,
+            "%s : i2c bulk write failed, %x = %x (%zu bytes)\n",
+            __func__, addr, val, nbytes);
+    else
+        dev_dbg(&priv->client->dev,
+            "%s : addr 0x%x, val=0x%x (%zu bytes)\n",
+            __func__, addr, val, nbytes);
+    return err;
+}
+
+/*
+ * imx547_common_regs - Function for setting common registers.
+ * @priv: Pointer to device structure
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_common_regs(struct stimx547 *priv)
+{
+    int err = 0;
+
+    err = imx547_write_table(priv, imx547_common_settings);
+    if (err)
+        return err;
+
+    dev_dbg(&priv->client->dev, "imx547 : imx547_common_regs !\n");
+
+    return err;
+}
+
+/*
+ * imx547_set_pixel_format - Function for setting registers for pixel format.
+ * @priv: Pointer to device structure
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_set_pixel_format(struct stimx547 *priv)
+{
+    int err = 0;
+
+    switch (priv->format.code) {
+        case MEDIA_BUS_FMT_SRGGB10_1X10:
+        case MEDIA_BUS_FMT_Y10_1X10:
+            err = imx547_write_table(priv, imx547_10bit_mode);
+            break;
+        case MEDIA_BUS_FMT_SRGGB12_1X12:
+        case MEDIA_BUS_FMT_Y12_1X12:
+            err = imx547_write_table(priv, imx547_12bit_mode);
+            break;
+        default:
+            dev_err(&priv->client->dev, "%s: unknown pixel format\n", __func__);
+            return -EINVAL;
+    }
+    dev_dbg(&priv->client->dev, "imx547 : imx547_set_pixel_format !\n");
+
+    return err;
+}
+
+/*
+ * imx547_start_stream - Function for starting stream
+ * @priv: Pointer to device structure
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_start_stream(struct stimx547 *priv)
+{
+    int err = 0;
+
+    err = imx547_write_reg(priv, STANDBY, 0x00);
+
+    /* "Internal regulator stabilization" time */
+    usleep_range(1138000, 1140000);
+
+    gpiod_set_value_cansleep(priv->gt_trx_reset_gpio, 1);
+    usleep_range(20000, 21000);
+    gpiod_set_value_cansleep(priv->gt_trx_reset_gpio, 0);
+
+    err |= imx547_write_reg(priv, XMSTA, 0x00);
+
+    dev_dbg(&priv->client->dev, "imx547 : imx547_start_stream !\n");
+    return 0;
+}
+
+/*
+ * imx547_stop_stream - Function for stoping stream
+ * @priv: Pointer to device structure
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_stop_stream(struct stimx547 *priv)
+{
+    int err = 0;
+
+    err = imx547_write_reg(priv, STANDBY, 0x01);
+
+    usleep_range(100, 110);
+       
+    err |= imx547_write_reg(priv, XMSTA, 0x01);
+
+
+    dev_dbg(&priv->client->dev, "imx547 : imx547_stop_stream !\n");
+    return 0;
+}
+
+
+/**
+ * imx547_s_ctrl - This is used to set the imx547 V4L2 controls
+ * @ctrl: V4L2 control to be set
+ *
+ * This function is used to set the V4L2 controls for the imx547 sensor.
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+    struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
+    struct stimx547 *imx547 = to_imx547(sd);
+    int ret = -EINVAL;
+
+    dev_dbg(&imx547->client->dev,
+        "%s : s_ctrl: %s, value: %d\n", __func__,
+        ctrl->name, ctrl->val);
+
+    switch (ctrl->id) {
+    case V4L2_CID_EXPOSURE:
+        dev_dbg(&imx547->client->dev,
+            "%s : set V4L2_CID_EXPOSURE\n", __func__);
+        ret = imx547_set_exposure(imx547, ctrl->val);
+        break;
+
+    case V4L2_CID_GAIN:
+        dev_dbg(&imx547->client->dev,
+            "%s : set V4L2_CID_GAIN\n", __func__);
+        ret = imx547_set_gain(imx547, ctrl->val);
+        break;
+
+    case V4L2_CID_TEST_PATTERN:
+        dev_dbg(&imx547->client->dev,
+            "%s : set V4L2_CID_TEST_PATTERN\n", __func__);
+        ret = imx547_set_test_pattern(imx547, ctrl->val);
+        break;
+
+    case V4L2_CID_BLACK_LEVEL:
+        dev_dbg(&imx547->client->dev,
+            "%s : set V4L2_CID_BLACK_LEVEL\n", __func__);
+        ret = imx547_set_black_level(imx547, ctrl->val);
+        break;
+
+    }
+
+    return ret;
+}
+
+
+/**
+ * imx547_get_fmt - Get the pad format
+ * @sd: Pointer to V4L2 Sub device structure
+ * @cfg: Pointer to sub device pad information structure
+ * @fmt: Pointer to pad level media bus format
+ *
+ * This function is used to get the pad format information.
+ *
+ * Return: 0 on success
+ */
+static int imx547_get_fmt(struct v4l2_subdev *sd,
+              struct v4l2_subdev_state *sd_state,
+              struct v4l2_subdev_format *fmt)
+{
+    struct stimx547 *imx547 = to_imx547(sd);
+
+    mutex_lock(&imx547->lock);
+    fmt->format = imx547->format;
+    mutex_unlock(&imx547->lock);
+    return 0;
+}
+
+/**
+ * imx547_set_fmt - This is used to set the pad format
+ * @sd: Pointer to V4L2 Sub device structure
+ * @cfg: Pointer to sub device pad information structure
+ * @format: Pointer to pad level media bus format
+ *
+ * This function is used to set the pad format.
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_fmt(struct v4l2_subdev *sd,
+              struct v4l2_subdev_state *sd_state,
+              struct v4l2_subdev_format *format)
+{
+    struct stimx547 *imx547 = to_imx547(sd);
+    int err = 0;
+
+    mutex_lock(&imx547->lock);
+    imx547->format = format->format;
+
+    switch (imx547->format.code) {
+        case MEDIA_BUS_FMT_SRGGB10_1X10:
+        case MEDIA_BUS_FMT_Y10_1X10:
+            imx547->line_time = IMX547_DEFAULT_LINE_TIME_10BIT;
+            break;
+        case MEDIA_BUS_FMT_SRGGB12_1X12:
+        case MEDIA_BUS_FMT_Y12_1X12:
+            imx547->line_time = IMX547_DEFAULT_LINE_TIME_12BIT;
+            break;
+        default:
+            dev_err(&imx547->client->dev, "%s: Cannot find line time\n", __func__);
+            return -EINVAL;
+    }
+
+    mutex_unlock(&imx547->lock);
+
+    return err;
+}
+
+
+/**
+ * imx547_g_frame_interval - Get the frame interval
+ * @sd: Pointer to V4L2 Sub device structure
+ * @fi: Pointer to V4l2 Sub device frame interval structure
+ *
+ * This function is used to get the frame interval.
+ *
+ * Return: 0 on success
+ */
+static int imx547_g_frame_interval(struct v4l2_subdev *sd,
+                   struct v4l2_subdev_frame_interval *fi)
+{
+    struct stimx547 *imx547 = to_imx547(sd);
+
+    fi->interval = imx547->frame_interval;
+    dev_dbg(&imx547->client->dev, "%s frame rate = %d / %d\n", __func__, imx547->frame_interval.numerator, imx547->frame_interval.denominator);
+
+    return 0;
+}
+
+/**
+ * imx547_s_frame_interval - Set the frame interval
+ * @sd: Pointer to V4L2 Sub device structure
+ * @fi: Pointer to V4l2 Sub device frame interval structure
+ *
+ * This function is used to set the frame interval.
+ *
+ * Return: 0 on success
+ */
+static int imx547_s_frame_interval(struct v4l2_subdev *sd,
+                   struct v4l2_subdev_frame_interval *fi)
+{
+    struct stimx547 *imx547 = to_imx547(sd);
+    struct v4l2_ctrl *ctrl = imx547->ctrls.exposure;
+    int min, max, def;
+    int ret;
+    u32 min_reg_shs;
+
+    mutex_lock(&imx547->lock);
+    imx547->frame_interval = fi->interval;
+    ret = imx547_set_frame_interval(imx547);
+    if (!ret) {
+        /*
+         * exposure time range is decided by frame interval
+         * need to update it after frame interval changes
+         */
+
+        switch (imx547->format.code) {
+            case MEDIA_BUS_FMT_SRGGB10_1X10:
+            case MEDIA_BUS_FMT_Y10_1X10:
+                min_reg_shs = IMX547_MIN_SHS_LENGTH_10BIT;
+                break;
+            case MEDIA_BUS_FMT_SRGGB12_1X12:
+            case MEDIA_BUS_FMT_Y12_1X12:
+                min_reg_shs = IMX547_MIN_SHS_LENGTH_12BIT;
+                break;
+            default:
+                dev_err(&imx547->client->dev, "%s: Cannot find minimum SHS\n", __func__);
+                return -EINVAL;
+        }
+
+        min = IMX547_MIN_EXPOSURE_TIME;
+        max = (imx547->frame_length - min_reg_shs) * imx547->line_time / IMX547_K_FACTOR;
+        def = max;
+        if (__v4l2_ctrl_modify_range(ctrl, min, max, 1, def)) {
+            dev_err(&imx547->client->dev,
+                "Exposure ctrl range update failed\n");
+            goto unlock;
+        }
+
+        /* update exposure time accordingly */
+        imx547_set_exposure(imx547, ctrl->val);
+
+        dev_dbg(&imx547->client->dev, "set frame interval to %llu us\n", fi->interval.numerator * IMX547_M_FACTOR / fi->interval.denominator);
+    }
+
+unlock:
+    mutex_unlock(&imx547->lock);
+
+    return ret;
+}
+
+/**
+ * imx547_s_stream - It is used to start/stop the streaming.
+ * @sd: V4L2 Sub device
+ * @on: Flag (True / False)
+ *
+ * This function controls the start or stop of streaming for the
+ * imx547 sensor.
+ *
+ * Return: 0 on success, errors otherwise
+ */
+static int imx547_s_stream(struct v4l2_subdev *sd, int on)
+{
+    struct stimx547 *imx547 = to_imx547(sd);
+    int ret = 0;
+
+    mutex_lock(&imx547->lock);
+
+    if (on) {
+
+        /* load common registers */
+        ret = imx547_common_regs(imx547);
+        if (ret)
+            goto fail;
+
+         /* load pixel format registers */
+        ret = imx547_set_pixel_format(imx547);
+        if (ret)
+            goto fail;
+
+        /* calculate line time */
+        ret = imx547_calculate_line_time(imx547);
+        if (ret)
+            goto fail;
+
+        /* update frame interval */
+        ret = imx547_set_frame_interval(imx547);
+        if (ret)
+            goto fail;
+
+        /* update exposure time */
+        ret = imx547_set_exposure(imx547, imx547->ctrls.exposure->val);
+        if (ret)
+            goto fail;
+
+        /* start stream */
+        ret = imx547_start_stream(imx547);
+        if (ret)
+            goto fail;
+    } else {
+        /* stop stream */
+        ret = imx547_stop_stream(imx547);
+        if (ret)
+            goto fail;
+    }
+
+    mutex_unlock(&imx547->lock);
+    dev_dbg(&imx547->client->dev, "%s : Done\n", __func__);
+    return 0;
+
+fail:
+    mutex_unlock(&imx547->lock);
+    dev_err(&imx547->client->dev, "s_stream failed\n");
+    return ret;
+}
+
+
+/*
+ * imx547_set_gain - Function called when setting gain
+ * @priv: Pointer to device structure
+ * @val: Value of gain
+ *
+ * Set the gain based on input value.
+ * The caller should hold the mutex lock imx547->lock if necessary
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_gain(struct stimx547 *priv, int val)
+{
+    
+    int err;
+
+    err = imx547_write_mbreg(priv, GAIN_LOW, val, 2);
+    if (err){
+        dev_dbg(&priv->client->dev, "%s: GAIN control error\n", __func__);
+        return err;
+    }
+
+    /* update gain */
+    priv->ctrls.gain->val = val;
+
+    dev_dbg(&priv->client->dev, "%s:  gain val [%d]\n",  __func__, val);
+
+    return 0;
+}
+
+/*
+ * imx547_set_black_level - Function called when setting black level
+ * @priv: Pointer to device structure
+ * @val: Value of black level
+ *
+ * Set the black level based on input value.
+ * The caller should hold the mutex lock imx547->lock if necessary
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_black_level(struct stimx547 *priv, int val)
+{
+    
+    int err;
+
+    err = imx547_write_mbreg(priv, BLKLEVEL_LOW, val, 2);
+    if (err){
+        dev_dbg(&priv->client->dev, "%s: BLKLEVEL control error\n", __func__);
+        return err;
+    }
+
+    /* update black level */
+    priv->ctrls.black_level->val = val;
+
+    dev_dbg(&priv->client->dev, "%s:  black level val [%d]\n",  __func__, val);
+
+    return 0;
+}
+
+/*
+ * imx547_set_exposure - Function called when setting exposure time
+ * @priv: Pointer to device structure
+ * @val: Variable for exposure time, in the unit of micro-second
+ *
+ * Set exposure time based on input value.
+ * The caller should hold the mutex lock imx547->lock if necessary
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_exposure(struct stimx547 *priv, int val)
+{
+    
+    int err = 0;
+    u32 integration_time_line;
+    u32 reg_shs, min_reg_shs;
+
+    dev_dbg(&priv->client->dev, "%s: integration time: %d [us]\n", __func__, val);
+
+    /* Check value with internal range */
+    if (val > priv->ctrls.exposure->maximum) {
+        val = priv->ctrls.exposure->maximum;
+    }
+    else if (val < priv->ctrls.exposure->minimum) {
+        val = priv->ctrls.exposure->minimum;
+    }
+
+    integration_time_line = (val * IMX547_K_FACTOR) / priv->line_time ;
+
+    reg_shs = priv->frame_length - integration_time_line;
+    
+    switch (priv->format.code) {
+        case MEDIA_BUS_FMT_SRGGB10_1X10:
+        case MEDIA_BUS_FMT_Y10_1X10:
+            min_reg_shs = IMX547_MIN_SHS_LENGTH_10BIT;
+            break;
+        case MEDIA_BUS_FMT_SRGGB12_1X12:
+        case MEDIA_BUS_FMT_Y12_1X12:
+            min_reg_shs = IMX547_MIN_SHS_LENGTH_12BIT;
+            break;
+        default:
+            dev_err(&priv->client->dev, "%s: Cannot find minimum SHS\n", __func__);
+            return -EINVAL;
+    }
+
+    if (reg_shs < min_reg_shs)
+        reg_shs = min_reg_shs;
+    else if (reg_shs > (priv->frame_length - 1))
+        reg_shs = priv->frame_length - 1;
+
+    err = imx547_write_mbreg(priv, SHS_LOW, reg_shs, 3);
+    if (err) {
+        dev_err(&priv->client->dev, "%s: failed to set exposure\n", __func__);
+        return err;
+    }
+
+    /* update exposure time */
+    priv->ctrls.exposure->val = val;
+
+    dev_dbg(&priv->client->dev,
+     "%s: set integration time: %d [us], coarse1:%d [line], shs: %d [line], frame length: %llu [line]\n",
+     __func__, val, integration_time_line, reg_shs, priv->frame_length);
+
+    return err;
+}
+
+/*
+ * imx547_set_test_pattern - Function called when setting test pattern
+ * @priv: Pointer to device structure
+ * @val: Variable for test pattern
+ *
+ * Set to different test patterns based on input value.
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_test_pattern(struct stimx547 *priv, int val)
+{
+
+    int err;
+
+    if (val) {
+        err = imx547_write_reg(priv, 0x3550, 0x07);
+        if (err) 
+            goto fail;
+
+        err = imx547_write_reg(priv, 0x3551, (u8)(val));
+        if (err) 
+            goto fail;
+    }
+    else {
+        err = imx547_write_reg(priv, 0x3550, 0x06);
+        if (err) 
+            goto fail;
+    }
+
+    return 0;
+
+fail:
+    dev_err(&priv->client->dev, "%s: error setting test pattern\n", __func__);
+    return err;
+}
+
+
+/*
+ * imx547_set_exposure - Function for calculating 1H time
+ * @priv: Pointer to device structure
+ *
+ * Calculate line time based on HMAX value.
+ *
+ * Return: 0 on success
+ */
+static int imx547_calculate_line_time(struct stimx547 *priv)
+{
+    u32 hmax;
+    int err;
+
+    err = imx547_read_mbreg(priv, HMAX_LOW, &hmax, 2);
+    if (err) {
+        dev_err(&priv->client->dev, "%s: unable to read hmax\n", __func__);
+        return err;
+    }
+
+    priv->line_time = (hmax*IMX547_G_FACTOR) / (IMX547_INCK);
+
+
+    dev_dbg(&priv->client->dev, "%s: hmax: %u [inck], line_time: %u [ns]\n",
+            __func__, hmax, priv->line_time);
+
+    return 0;
+}
+
+
+/*
+ * imx547_set_frame_length - Function called when setting frame length
+ * @priv: Pointer to device structure
+ *
+ * Set frame length.
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_frame_length(struct stimx547 *priv)
+{
+    int err;
+    u32 frame_length_32bit;
+
+    frame_length_32bit = (u32)priv->frame_length;
+
+    err = imx547_write_mbreg(priv, VMAX_LOW, frame_length_32bit, 3);
+    if (err) {
+        dev_err(&priv->client->dev, "%s unable to write vmax\n", __func__);
+        return err;
+    }
+
+    dev_dbg(&priv->client->dev, "%s : input length = %llu\n", __func__, priv->frame_length);
+
+    return 0;
+}
+
+/*
+ * imx547_set_frame_interval - Function called when setting frame interval
+ * @priv: Pointer to device structure
+ *
+ * Change frame interval by updating VMAX value
+ * The caller should hold the mutex lock imx547->lock if necessary
+ *
+ * Return: 0 on success
+ */
+static int imx547_set_frame_interval(struct stimx547 *priv)
+{
+    int err;
+    u64 frame_length;
+    u64 req_frame_rate;
+    u32 max_frame_rate;
+
+	dev_dbg(&priv->client->dev, "%s: input frame interval = %d / %d", 
+			__func__, priv->frame_interval.numerator, priv->frame_interval.denominator);
+
+    if (priv->frame_interval.numerator == 0 || priv->frame_interval.denominator == 0) {
+        priv->frame_interval.denominator = IMX547_DEF_FRAME_RATE;
+        priv->frame_interval.numerator = 1;
+    }
+
+    req_frame_rate = IMX547_M_FACTOR * priv->frame_interval.denominator / priv->frame_interval.numerator;
+
+    switch (priv->format.code) {
+        case MEDIA_BUS_FMT_SRGGB10_1X10:
+        case MEDIA_BUS_FMT_Y10_1X10:
+            max_frame_rate = IMX547_M_FACTOR * IMX547_MAX_FRAME_INTERVAL_10BIT_DENOMINATOR / IMX547_MAX_FRAME_INTERVAL_10BIT_NUMERATOR;
+            break;
+        case MEDIA_BUS_FMT_SRGGB12_1X12:
+        case MEDIA_BUS_FMT_Y12_1X12:
+            max_frame_rate = IMX547_M_FACTOR * IMX547_MAX_FRAME_INTERVAL_12BIT_DENOMINATOR / IMX547_MAX_FRAME_INTERVAL_12BIT_NUMERATOR;
+            break;
+        default:
+            dev_err(&priv->client->dev, "%s: Cannot find maximum frame rate\n", __func__);
+            return -EINVAL;
+    }
+
+    /* boundary check */
+    if (req_frame_rate > max_frame_rate) {
+        switch (priv->format.code) {
+            case MEDIA_BUS_FMT_SRGGB10_1X10:
+            case MEDIA_BUS_FMT_Y10_1X10:
+                priv->frame_interval.numerator = IMX547_MAX_FRAME_INTERVAL_10BIT_NUMERATOR;
+                priv->frame_interval.denominator = IMX547_MAX_FRAME_INTERVAL_10BIT_DENOMINATOR ;
+                break;
+            case MEDIA_BUS_FMT_SRGGB12_1X12:
+            case MEDIA_BUS_FMT_Y12_1X12:
+                priv->frame_interval.numerator = IMX547_MAX_FRAME_INTERVAL_12BIT_NUMERATOR;
+                priv->frame_interval.denominator = IMX547_MAX_FRAME_INTERVAL_12BIT_DENOMINATOR ;
+                break;
+            default:
+                dev_err(&priv->client->dev, "%s: Frame interval setting error\n", __func__);
+                return -EINVAL;
+        }
+    } else if (req_frame_rate < (IMX547_MIN_FRAME_RATE * IMX547_M_FACTOR)) {
+        priv->frame_interval.numerator = 1;
+        priv->frame_interval.denominator = IMX547_MIN_FRAME_RATE;
+    }
+
+    req_frame_rate = IMX547_M_FACTOR * priv->frame_interval.denominator / priv->frame_interval.numerator;
+
+    frame_length = (IMX547_M_FACTOR * IMX547_G_FACTOR) / (req_frame_rate * priv->line_time);
+    priv->frame_length = frame_length;
+    dev_dbg(&priv->client->dev, "%s: req_frame_rate: %llu line time: %d, frame_length:%llu  \n",
+			 __func__, req_frame_rate, priv->line_time, frame_length);
+
+    err = imx547_set_frame_length(priv);
+    if (err)
+        goto fail;
+
+    return 0;
+
+fail:
+    dev_err(&priv->client->dev, "%s error = %d\n", __func__, err);
+    return err;
+}
+
+static const struct v4l2_subdev_pad_ops imx547_pad_ops = {
+    .get_fmt = imx547_get_fmt,
+    .set_fmt = imx547_set_fmt,
+};
+
+static const struct v4l2_subdev_video_ops imx547_video_ops = {
+    .g_frame_interval = imx547_g_frame_interval,
+    .s_frame_interval = imx547_s_frame_interval,
+    .s_stream = imx547_s_stream,
+};
+
+static const struct v4l2_subdev_ops imx547_subdev_ops = {
+    .pad = &imx547_pad_ops,
+    .video = &imx547_video_ops,
+};
+
+static const struct v4l2_ctrl_ops imx547_ctrl_ops = {
+    .s_ctrl = imx547_s_ctrl,
+};
+
+
+static int imx547_probe(struct i2c_client *client)
+{
+    struct v4l2_subdev *sd;
+    struct stimx547 *imx547;
+    int ret;
+
+    /* initialize imx547 */
+    imx547 = devm_kzalloc(&client->dev, sizeof(*imx547), GFP_KERNEL);
+    if (!imx547)
+        return -ENOMEM;
+
+    mutex_init(&imx547->lock);
+
+    /* initialize format */
+    imx547->format.width = IMX547_DEFAULT_WIDTH;
+    imx547->format.height = IMX547_DEFAULT_HEIGHT;
+    imx547->format.field = V4L2_FIELD_NONE;
+    imx547->format.code = MEDIA_BUS_FMT_SRGGB12_1X12;
+    imx547->format.colorspace = V4L2_COLORSPACE_SRGB;
+    imx547->frame_interval.numerator = 1;
+    imx547->frame_interval.denominator = IMX547_DEF_FRAME_RATE;
+    imx547->frame_length = IMX547_DEFAULT_HEIGHT + IMX547_MIN_FRAME_DELTA;
+
+    /* initialize regmap */
+    imx547->regmap = devm_regmap_init_i2c(client, &imx547_regmap_config);
+    if (IS_ERR(imx547->regmap)) {
+        dev_err(&client->dev,
+            "regmap init failed: %ld\n", PTR_ERR(imx547->regmap));
+        ret = -ENODEV;
+        goto err_regmap;
+    }
+
+    /* initialize subdevice */
+    imx547->client = client;
+    sd = &imx547->sd;
+    v4l2_i2c_subdev_init(sd, client, &imx547_subdev_ops);
+    sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
+
+    /* initialize subdev media pad */
+    imx547->pad.flags = MEDIA_PAD_FL_SOURCE;
+    sd->entity.function = MEDIA_ENT_F_CAM_SENSOR;
+    ret = media_entity_pads_init(&sd->entity, 1, &imx547->pad);
+    if (ret < 0) {
+        dev_err(&client->dev,
+            "%s : media entity init Failed %d\n", __func__, ret);
+        goto err_regmap;
+    }
+
+    /* initialize gt trx reset gpio */
+    imx547->gt_trx_reset_gpio = devm_gpiod_get_index_optional(&client->dev, "reset",
+                                0, GPIOD_OUT_HIGH);
+    if (IS_ERR(imx547->gt_trx_reset_gpio)) {
+        if (PTR_ERR(imx547->gt_trx_reset_gpio) != -EPROBE_DEFER)
+            dev_err(&client->dev, "GT TRX Reset GPIO not setup in DT");
+        ret = PTR_ERR(imx547->gt_trx_reset_gpio);
+        goto err_me;
+    }
+
+    /* initialize pipe reset gpio */
+    imx547->pipe_reset_gpio = devm_gpiod_get_index_optional(&client->dev, "reset",
+                              1, GPIOD_OUT_HIGH);
+    if (IS_ERR(imx547->pipe_reset_gpio)) {
+        if (PTR_ERR(imx547->pipe_reset_gpio) != -EPROBE_DEFER)
+            dev_err(&client->dev, "GT TRX Reset GPIO not setup in DT");
+        ret = PTR_ERR(imx547->pipe_reset_gpio);
+        goto err_me;
+    }
+    gpiod_set_value_cansleep(imx547->pipe_reset_gpio, 0);
+
+    /* initialize controls */
+    ret = v4l2_ctrl_handler_init(&imx547->ctrls.handler, 3);
+    if (ret < 0) {
+        dev_err(&client->dev,
+            "%s : ctrl handler init Failed\n", __func__);
+        goto err_me;
+    }
+
+    imx547->ctrls.handler.lock = &imx547->lock;
+
+    /* add new controls */
+    imx547->ctrls.test_pattern = v4l2_ctrl_new_std_menu_items(
+        &imx547->ctrls.handler, &imx547_ctrl_ops,
+        V4L2_CID_TEST_PATTERN,
+        ARRAY_SIZE(tp_qmenu) - 1, 0, 0, tp_qmenu);
+
+    imx547->ctrls.gain = v4l2_ctrl_new_std(
+        &imx547->ctrls.handler,
+        &imx547_ctrl_ops,
+        V4L2_CID_GAIN, IMX547_MIN_GAIN,
+        IMX547_MAX_GAIN, 1,
+        IMX547_DEF_GAIN);
+
+    imx547->ctrls.exposure = v4l2_ctrl_new_std(
+        &imx547->ctrls.handler,
+        &imx547_ctrl_ops,
+        V4L2_CID_EXPOSURE, IMX547_MIN_EXPOSURE_TIME,
+        IMX547_M_FACTOR / IMX547_DEF_FRAME_RATE, 1,
+        IMX547_DEF_EXPOSURE_TIME);
+
+    imx547->ctrls.black_level = v4l2_ctrl_new_std(
+        &imx547->ctrls.handler,
+        &imx547_ctrl_ops,
+        V4L2_CID_BLACK_LEVEL, IMX547_MIN_BLACK_LEVEL,
+        IMX547_MAX_BLACK_LEVEL_10BIT, 1,
+        IMX547_DEF_BLACK_LEVEL_10BIT);
+
+    imx547->sd.ctrl_handler = &imx547->ctrls.handler;
+    if (imx547->ctrls.handler.error) {
+        ret = imx547->ctrls.handler.error;
+        goto err_ctrls;
+    }
+
+    /* setup default controls */
+    ret = v4l2_ctrl_handler_setup(&imx547->ctrls.handler);
+    if (ret) {
+        dev_err(&client->dev,
+            "Error %d setup default controls\n", ret);
+        goto err_ctrls;
+    }
+
+    /* register subdevice */
+    ret = v4l2_async_register_subdev(sd);
+    if (ret < 0) {
+        dev_err(&client->dev,
+            "%s : v4l2_async_register_subdev failed %d\n",
+            __func__, ret);
+        goto err_ctrls;
+    }
+
+    dev_info(&client->dev, "imx547 : imx547 probe success !\n");
+    return 0;
+
+err_ctrls:
+    v4l2_ctrl_handler_free(&imx547->ctrls.handler);
+err_me:
+    media_entity_cleanup(&sd->entity);
+err_regmap:
+    mutex_destroy(&imx547->lock);
+    return ret;
+}
+
+static int imx547_remove(struct i2c_client *client)
+{
+    struct v4l2_subdev *sd = i2c_get_clientdata(client);
+    struct stimx547 *imx547 = to_imx547(sd);
+
+    /* stop stream */
+    imx547_stop_stream(imx547);
+
+    v4l2_async_unregister_subdev(sd);
+    v4l2_ctrl_handler_free(&imx547->ctrls.handler);
+    media_entity_cleanup(&sd->entity);
+    mutex_destroy(&imx547->lock);
+    return 0;
+}
+
+static const struct i2c_device_id imx547_id[] = {
+    { "imx547", 0 },
+    { }
+};
+
+MODULE_DEVICE_TABLE(i2c, imx547_id);
+
+static struct i2c_driver imx547_i2c_driver = {
+    .driver = {
+        .name   = "imx547",
+        .of_match_table = imx547_of_match,
+    },
+    .probe_new  = imx547_probe,
+    .remove     = imx547_remove,
+    .id_table   = imx547_id,
+};
+
+module_i2c_driver(imx547_i2c_driver);
+
+MODULE_AUTHOR("FRAMOS GmbH");
+MODULE_DESCRIPTION("IMX547 CMOS Image Sensor driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-mv-camera-sensor-module/imx547_mode_tbls.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-mv-camera-sensor-module/imx547_mode_tbls.h
@@ -0,0 +1,489 @@
+/*
+ * imx547_mode_tbls.h - imx547 sensor mode tables
+ *
+ * Copyright (c) 2022. FRAMOS.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __IMX547_TABLES__
+#define __IMX547_TABLES__
+
+/**
+ * Image sensor registers as described in the IMX547 register map
+ */
+
+#define STANDBY             0x3000
+#define XMSTA               0x3010
+
+#define INCKSEL_ST0         0x3014
+#define INCKSEL_ST1         0x3015
+#define INCKSEL_ST2         0x3016
+#define INCKSEL_ST3         0x3018
+#define INCKSEL_ST4         0x3019
+#define INCKSEL_ST5         0x301B
+#define REGHOLD             0x3034
+#define HVMODE              0x303C
+#define VOPB_VBLK_HWID_LOW  0x30D0
+#define VOPB_VBLK_HWID_HIGH 0x30D1
+#define FINFO_HWIDTH_LOW    0x30D2
+#define FINFO_HWIDTH_HIGH   0x30D3
+
+#define VMAX_LOW            0x30D4
+#define VMAX_MID            0x30D5
+#define VMAX_HIGH           0x30D6
+#define HMAX_LOW            0x30D8
+#define HMAX_HIGH           0x30D9
+#define FREQ                0x30DC
+#define GMRWT               0x30E2
+#define GMTWT               0x30E3
+#define GAINDLY             0x30E5
+#define GSDLY               0x30E6
+
+
+#define ADBIT               0x3200
+#define HREVERSE_VREVERSE   0x3204
+
+#define INCKSEL_N0          0x321C
+#define INCKSEL_N1          0x321D
+#define INCKSEL_N2          0x321E
+#define INCKSEL_N3          0x321F
+
+#define INCKSEL_S0          0x3220
+#define INCKSEL_S1          0x3221
+#define INCKSEL_S2          0x3222
+#define INCKSEL_S3          0x3223
+
+#define INCKSEL_D0          0x3224
+#define INCKSEL_D1          0x3225
+#define INCKSEL_D2          0x3226
+#define INCKSEL_D3          0x3227
+
+#define SLVS_EN             0x322B
+#define LLBLANK_LOW         0x323C
+#define LLBLANK_HIGH        0x323D
+#define VINT_EN             0x323E
+
+#define SHS_LOW             0x3240
+#define SHS_MID             0x3241
+#define SHS_HIGH            0x3242
+
+#define TRIGMODE            0x3400
+#define ODBIT               0x3430
+#define SYNCSEL             0x343C
+#define STBSLVS             0x3444
+
+#define GAIN_RTS            0x3502
+#define GAIN_LOW            0x3514
+#define GAIN_HIGH           0x3515
+#define BLKLEVEL_LOW        0x35B4
+#define BLKLEVEL_HIGH       0x35B5
+
+#define LANESEL             0x3904
+#define IDLECODE1_LOW       0x3934 
+#define IDLECODE1_HIGH      0x3935 
+#define IDLECODE2_LOW       0x3936 
+#define IDLECODE2_HIGH      0x3937 
+#define IDLECODE3_LOW       0x3938 
+#define IDLECODE3_HIGH      0x3939 
+#define IDLECODE4_LOW       0x393A 
+#define IDLECODE4_HIGH      0x393B 
+
+#define CRC_ECC_MODE        0x3A00
+
+/**
+ * Resolutions of implemented frame modes
+ */
+
+#define IMX547_DEFAULT_WIDTH        2472
+#define IMX547_DEFAULT_HEIGHT       2064
+
+/**
+ * Special values for the write table function
+ */
+#define IMX547_TABLE_WAIT_MS 0
+#define IMX547_TABLE_END     1
+#define IMX547_WAIT_MS       10
+
+#define IMX547_MIN_FRAME_DELTA  144
+
+#define IMX547_TO_LOW_BYTE(x) (x & 0xFF)
+#define IMX547_TO_MID_BYTE(x) (x >> 8)
+
+/*
+ * imx547 I2C operation related structure
+ */
+struct reg_8 {
+    u16 addr;
+    u8 val;
+};
+
+typedef struct reg_8 imx547_reg;
+
+/**
+ * Tables for the write table function
+ */
+
+static const imx547_reg imx547_stop[] = {
+
+    {STANDBY,              0x01},
+    {IMX547_TABLE_WAIT_MS, IMX547_WAIT_MS},
+    {XMSTA,                0x01},
+
+    {IMX547_TABLE_WAIT_MS, 30},
+    {IMX547_TABLE_END,     0x00}
+};
+
+static const imx547_reg imx547_10bit_mode[] = {
+
+    {HMAX_LOW,      IMX547_TO_LOW_BYTE(274)}, 
+    {HMAX_HIGH,     IMX547_TO_MID_BYTE(274)}, 
+    {VMAX_LOW,      IMX547_TO_LOW_BYTE(2216)}, 
+    {VMAX_MID,      IMX547_TO_MID_BYTE(2216)}, 
+
+    {GMRWT,     0x08},
+    {GMTWT,     0x32},
+    {GAINDLY,   0x02},
+    {GSDLY,     0x08},
+
+    {ADBIT,     0x05},
+    {ODBIT,     0x00},
+
+    {0x35A4,    0x1C},
+    {0x35A8,    0x1C},
+    {0x35EC,    0x1C},
+
+    {0x362C,    0x1C},
+    {0x362E,    0xEB},
+    {0x362F,    0x1F},
+    {0x3654,    0x1C},
+    {0x3656,    0xEB},
+    {0x3657,    0x1F},
+    {0x367C,    0x1C},
+    {0x367E,    0xEB},
+    {0x367F,    0x1F},
+    {0x36E8,    0x11},
+
+    {0x4056,    0x0F},
+    {0x4096,    0x0F},
+
+    {0x4460,    0x6C},
+
+    {0x45E6,    0x53},
+    {0x45F0,    0x90},
+    {0x45F2,    0x8A},
+    {0x45F8,    0x8E},
+    {0x45FA,    0x90},
+
+
+    {0x4604,    0x8E},
+    {0x4606,    0x90},
+    {0x460C,    0x8A},
+    {0x460E,    0xBB},
+    {0x4614,    0x90},
+    {0x4616,    0x8A},
+    {0x4634,    0x4A},
+    {0x4636,    0x90},
+    {0x463C,    0x4C},
+    {0x463E,    0x92},
+    {0x4644,    0x4E},
+    {0x4646,    0x94},
+    {0x464C,    0x47},
+    {0x464E,    0x4D},
+    {0x4654,    0x49},
+    {0x4656,    0x50},
+    {0x465C,    0x4B},
+    {0x465E,    0x52},
+    {0x466A,    0x9E},
+    {0x4670,    0x98},
+    {0x4676,    0x96},
+    {0x4678,    0xBA},
+    {0x4698,    0x93},
+    {0x469A,    0xB9},
+
+    {0x4728,    0xD4},
+    {0x4729,    0x0E},
+    {0x472E,    0x05},
+    {0x472F,    0x04},
+    {0x4730,    0x04},
+    {0x4731,    0x04},
+
+    {0x4900,    0x64},
+    {0x4908,    0x6E},
+
+    {IMX547_TABLE_WAIT_MS, IMX547_WAIT_MS},
+    {IMX547_TABLE_END,     0x00}
+};
+
+static const imx547_reg imx547_12bit_mode[] = {
+
+    {HMAX_LOW,      IMX547_TO_LOW_BYTE(408)}, 
+    {HMAX_HIGH,     IMX547_TO_MID_BYTE(408)}, 
+    {VMAX_LOW,      IMX547_TO_LOW_BYTE(2208)}, 
+    {VMAX_MID,      IMX547_TO_MID_BYTE(2208)}, 
+
+    {GMRWT,     0x06},
+    {GMTWT,     0x24},
+    {GAINDLY,   0x02},
+    {GSDLY,     0x10},
+
+    {ADBIT,     0x15},
+    {ODBIT,     0x01},
+
+    {0x35A4,    0x08},
+    {0x35A8,    0x08},
+    {0x35EC,    0x08},
+
+    {0x362C,    0x64},
+    {0x362E,    0x00},
+    {0x362F,    0x00},
+    {0x3654,    0x64},
+    {0x3656,    0x20},
+    {0x3657,    0x00},
+    {0x367C,    0x64},
+    {0x367E,    0x00},
+    {0x367F,    0x00},
+    {0x36E8,    0x13},
+
+    {0x4056,    0x23},
+    {0x4096,    0x23},
+
+    {0x4460,    0x6E},
+
+    {0x45E6,    0x3F},
+    {0x45F0,    0x95},
+    {0x45F2,    0x8F},
+    {0x45F8,    0x93},
+    {0x45FA,    0x95},
+
+
+    {0x4604,    0x93},
+    {0x4606,    0x95},
+    {0x460C,    0x8F},
+    {0x460E,    0xC0},
+    {0x4614,    0x95},
+    {0x4616,    0x8F},
+    {0x4634,    0x36},
+    {0x4636,    0x95},
+    {0x463C,    0x38},
+    {0x463E,    0x97},
+    {0x4644,    0x3A},
+    {0x4646,    0x99},
+    {0x464C,    0x33},
+    {0x464E,    0x39},
+    {0x4654,    0x35},
+    {0x4656,    0x3C},
+    {0x465C,    0x37},
+    {0x465E,    0x3E},
+    {0x466A,    0xA3},
+    {0x4670,    0x9D},
+    {0x4676,    0x9B},
+    {0x4678,    0xBF},
+    {0x4698,    0x98},
+    {0x469A,    0xBE},
+
+    {0x4728,    0xFB},
+    {0x4729,    0x07},
+    {0x472E,    0x06},
+    {0x472F,    0x06},
+    {0x4730,    0x06},
+    {0x4731,    0x06},
+
+    {0x4900,    0x6C},
+    {0x4908,    0x68},
+
+    {IMX547_TABLE_WAIT_MS, IMX547_WAIT_MS},
+    {IMX547_TABLE_END,     0x00}
+};
+
+static const imx547_reg imx547_common_settings[] = {
+
+    {FREQ,          0x00},
+    {INCKSEL_ST0,   0x0A},
+    {INCKSEL_ST1,   0x22},
+    {INCKSEL_ST2,   0xB1},
+    {INCKSEL_ST3,   0x40},
+    {INCKSEL_ST4,   0x04},
+    {INCKSEL_ST5,   0x3A},
+
+    {INCKSEL_N0,    0x80},
+    {INCKSEL_N1,    0x05},
+    {INCKSEL_N2,    0xE0},
+    {INCKSEL_N3,    0x00},
+
+    {INCKSEL_S0,    0x80},
+    {INCKSEL_S1,    0x05},
+    {INCKSEL_S2,    0xE0},
+    {INCKSEL_S3,    0x00},
+
+    {INCKSEL_D0,    0x10},
+    {INCKSEL_D1,    0x14},
+    {INCKSEL_D2,    0x20},
+    {INCKSEL_D3,    0xC0},
+
+    {SLVS_EN,       0x02},
+    {LLBLANK_LOW,   0x19},
+    {VINT_EN,       0x33},
+    {CRC_ECC_MODE,  0xD1},
+    {VOPB_VBLK_HWID_LOW,    0xA8},
+    {VOPB_VBLK_HWID_HIGH,   0x09},
+    {FINFO_HWIDTH_LOW,      0xA8},
+    {FINFO_HWIDTH_HIGH,     0x09},
+    {IDLECODE1_LOW,     0x3C},
+    {IDLECODE1_HIGH,    0x01},
+    {IDLECODE2_LOW,     0xBC},
+    {IDLECODE2_HIGH,    0x01},
+    {IDLECODE3_LOW,     0x3C},
+    {IDLECODE3_HIGH,    0x01},
+    {IDLECODE4_LOW,     0x3C},
+    {IDLECODE4_HIGH,    0x01},
+
+    {HVMODE,    0x03},
+    {LANESEL,   0x03},
+
+    {GAIN_RTS,  0x09},
+    {SYNCSEL,   0xF0}, 
+
+    {0x3004,    0xA8},
+    {0x3005,    0x02},
+
+    {0x3233,    0x00},
+
+    {0x3521,    0x3D},
+    {0x3535,    0x00},
+    {0x3542,    0x27},
+    {0x3546,    0x0F},
+    {0x354A,    0x20},
+    {0x359C,    0x0F},
+    {0x359D,    0x02},
+    {0x35A5,    0x12},
+    {0x35A9,    0x62},
+    {0x35CE,    0x0E},
+    {0x35ED,    0x12},
+    {0x35F0,    0xFB},
+    {0x35F1,    0x0B},
+    {0x35F2,    0xFB},
+    {0x35F3,    0x0B},
+    
+    {0x3642,    0x10},
+    {0x366A,    0x2E},
+    {0x3670,    0xC3},
+    {0x3672,    0x05},
+    {0x3674,    0xB6},
+    {0x3675,    0x01},
+    {0x3676,    0x05},
+    {0x3692,    0x10},
+    {0x36F5,    0x0F},
+    
+    {0x3797,    0x20},
+
+    {0x3E2E,    0x07},
+    {0x3E30,    0x4E},
+    {0x3E6E,    0x07},
+    {0x3E70,    0x35},
+    {0x3E96,    0x01},
+    {0x3E9E,    0x38},
+    {0x3EA0,    0x4C},
+
+    {0x3F3A,    0x04},
+
+    {0x4182,    0x00},
+    {0x41A2,    0x03},
+
+    {0x4232,    0x3C},
+    {0x4235,    0x22},
+
+    {0x4306,    0x00},
+    {0x4307,    0x00},
+    {0x4308,    0x00},
+    {0x4309,    0x00},
+    {0x4310,    0x04},
+    {0x4311,    0x04},
+    {0x4312,    0x04},
+    {0x4313,    0x04},
+    {0x431E,    0x16},
+    {0x431F,    0x16},
+    {0x433C,    0x8A},
+    {0x433D,    0x02},
+    {0x433E,    0xE8},
+    {0x433F,    0x05},
+    {0x4340,    0x9E},
+    {0x4341,    0x0C},
+
+    {0x446A,    0x4C},
+    {0x446E,    0x51},
+    {0x4472,    0x57},
+    {0x4476,    0x79},
+    {0x448A,    0x4C},
+    {0x448E,    0x51},
+    {0x4492,    0x57},
+    {0x4496,    0x79},
+    {0x44EC,    0x3F},
+    {0x44F0,    0x44},
+    {0x44F4,    0x4A},
+
+    {0x4510,    0x3F},
+    {0x4514,    0x44},
+    {0x4518,    0x4A},
+    {0x4576,    0xBE},
+    {0x457A,    0xB1},
+    {0x4580,    0xBC},
+    {0x4584,    0xAF},
+
+    {0x473C,    0x06},
+    {0x473D,    0x06},
+    {0x473E,    0x06},
+    {0x473F,    0x06},
+    {0x4749,    0x9F},
+    {0x474A,    0x99},
+    {0x474B,    0x09},
+    {0x4753,    0x90},
+    {0x4754,    0x99},
+    {0x4755,    0x09},
+    {0x4788,    0x04},
+
+    {0x4864,    0xDC},
+    {0x4868,    0xDC},
+    {0x486C,    0xDC},
+    {0x4874,    0xDC},
+    {0x4878,    0xDC},
+    {0x487C,    0xDC},
+    {0x48A4,    0xF4},
+    {0x48A8,    0xF4},
+    {0x48AC,    0xF4},
+    {0x48B4,    0xF4},
+    {0x48B8,    0xF4},
+    {0x48BC,    0xF4},
+
+    {0x4901,    0x0A},
+    {0x4902,    0x01},
+    {0x4916,    0x00},
+    {0x4917,    0x00},
+    {0x4918,    0xFF},
+    {0x4919,    0x0F},
+    {0x491E,    0xFF},
+    {0x491F,    0x0F},
+    {0x4920,    0x00},
+    {0x4921,    0x00},
+    {0x4926,    0xFF},
+    {0x4927,    0x0F},
+    {0x4928,    0x00},
+    {0x4929,    0x00},
+
+    {0x4A34,    0x0A},
+
+    {IMX547_TABLE_WAIT_MS,      IMX547_WAIT_MS},
+    {IMX547_TABLE_END,          0x0000}
+};
+
+#endif /* __IMX547_TABLES__ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/Kbuild
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/Kbuild
@@ -0,0 +1,4 @@
+obj-m	+= common/
+obj-m	+= al5e/
+obj-m	+= al5d/
+obj-m	+= dmaproxy/
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/Kconfig
@@ -0,0 +1,9 @@
+menuconfig ALLEGRO
+	tristate "Allegro video codec drivers"
+	help
+	  Enable Allegro video codec drivers
+
+if ALLEGRO
+source "drivers/staging/allegro/al5e/Kconfig"
+source "drivers/staging/allegro/al5d/Kconfig"
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/LICENSE.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/LICENSE.md
@@ -0,0 +1,340 @@
+		    GNU GENERAL PUBLIC LICENSE
+		       Version 2, June 1991
+
+ Copyright (C) 1989, 1991 Free Software Foundation, Inc.
+                       51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+			    Preamble
+
+  The licenses for most software are designed to take away your
+freedom to share and change it.  By contrast, the GNU General Public
+License is intended to guarantee your freedom to share and change free
+software--to make sure the software is free for all its users.  This
+General Public License applies to most of the Free Software
+Foundation's software and to any other program whose authors commit to
+using it.  (Some other Free Software Foundation software is covered by
+the GNU Library General Public License instead.)  You can apply it to
+your programs, too.
+
+  When we speak of free software, we are referring to freedom, not
+price.  Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+this service if you wish), that you receive source code or can get it
+if you want it, that you can change the software or use pieces of it
+in new free programs; and that you know you can do these things.
+
+  To protect your rights, we need to make restrictions that forbid
+anyone to deny you these rights or to ask you to surrender the rights.
+These restrictions translate to certain responsibilities for you if you
+distribute copies of the software, or if you modify it.
+
+  For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must give the recipients all the rights that
+you have.  You must make sure that they, too, receive or can get the
+source code.  And you must show them these terms so they know their
+rights.
+
+  We protect your rights with two steps: (1) copyright the software, and
+(2) offer you this license which gives you legal permission to copy,
+distribute and/or modify the software.
+
+  Also, for each author's protection and ours, we want to make certain
+that everyone understands that there is no warranty for this free
+software.  If the software is modified by someone else and passed on, we
+want its recipients to know that what they have is not the original, so
+that any problems introduced by others will not reflect on the original
+authors' reputations.
+
+  Finally, any free program is threatened constantly by software
+patents.  We wish to avoid the danger that redistributors of a free
+program will individually obtain patent licenses, in effect making the
+program proprietary.  To prevent this, we have made it clear that any
+patent must be licensed for everyone's free use or not licensed at all.
+
+  The precise terms and conditions for copying, distribution and
+modification follow.
+
+		    GNU GENERAL PUBLIC LICENSE
+   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
+
+  0. This License applies to any program or other work which contains
+a notice placed by the copyright holder saying it may be distributed
+under the terms of this General Public License.  The "Program", below,
+refers to any such program or work, and a "work based on the Program"
+means either the Program or any derivative work under copyright law:
+that is to say, a work containing the Program or a portion of it,
+either verbatim or with modifications and/or translated into another
+language.  (Hereinafter, translation is included without limitation in
+the term "modification".)  Each licensee is addressed as "you".
+
+Activities other than copying, distribution and modification are not
+covered by this License; they are outside its scope.  The act of
+running the Program is not restricted, and the output from the Program
+is covered only if its contents constitute a work based on the
+Program (independent of having been made by running the Program).
+Whether that is true depends on what the Program does.
+
+  1. You may copy and distribute verbatim copies of the Program's
+source code as you receive it, in any medium, provided that you
+conspicuously and appropriately publish on each copy an appropriate
+copyright notice and disclaimer of warranty; keep intact all the
+notices that refer to this License and to the absence of any warranty;
+and give any other recipients of the Program a copy of this License
+along with the Program.
+
+You may charge a fee for the physical act of transferring a copy, and
+you may at your option offer warranty protection in exchange for a fee.
+
+  2. You may modify your copy or copies of the Program or any portion
+of it, thus forming a work based on the Program, and copy and
+distribute such modifications or work under the terms of Section 1
+above, provided that you also meet all of these conditions:
+
+    a) You must cause the modified files to carry prominent notices
+    stating that you changed the files and the date of any change.
+
+    b) You must cause any work that you distribute or publish, that in
+    whole or in part contains or is derived from the Program or any
+    part thereof, to be licensed as a whole at no charge to all third
+    parties under the terms of this License.
+
+    c) If the modified program normally reads commands interactively
+    when run, you must cause it, when started running for such
+    interactive use in the most ordinary way, to print or display an
+    announcement including an appropriate copyright notice and a
+    notice that there is no warranty (or else, saying that you provide
+    a warranty) and that users may redistribute the program under
+    these conditions, and telling the user how to view a copy of this
+    License.  (Exception: if the Program itself is interactive but
+    does not normally print such an announcement, your work based on
+    the Program is not required to print an announcement.)
+
+These requirements apply to the modified work as a whole.  If
+identifiable sections of that work are not derived from the Program,
+and can be reasonably considered independent and separate works in
+themselves, then this License, and its terms, do not apply to those
+sections when you distribute them as separate works.  But when you
+distribute the same sections as part of a whole which is a work based
+on the Program, the distribution of the whole must be on the terms of
+this License, whose permissions for other licensees extend to the
+entire whole, and thus to each and every part regardless of who wrote it.
+
+Thus, it is not the intent of this section to claim rights or contest
+your rights to work written entirely by you; rather, the intent is to
+exercise the right to control the distribution of derivative or
+collective works based on the Program.
+
+In addition, mere aggregation of another work not based on the Program
+with the Program (or with a work based on the Program) on a volume of
+a storage or distribution medium does not bring the other work under
+the scope of this License.
+
+  3. You may copy and distribute the Program (or a work based on it,
+under Section 2) in object code or executable form under the terms of
+Sections 1 and 2 above provided that you also do one of the following:
+
+    a) Accompany it with the complete corresponding machine-readable
+    source code, which must be distributed under the terms of Sections
+    1 and 2 above on a medium customarily used for software interchange; or,
+
+    b) Accompany it with a written offer, valid for at least three
+    years, to give any third party, for a charge no more than your
+    cost of physically performing source distribution, a complete
+    machine-readable copy of the corresponding source code, to be
+    distributed under the terms of Sections 1 and 2 above on a medium
+    customarily used for software interchange; or,
+
+    c) Accompany it with the information you received as to the offer
+    to distribute corresponding source code.  (This alternative is
+    allowed only for noncommercial distribution and only if you
+    received the program in object code or executable form with such
+    an offer, in accord with Subsection b above.)
+
+The source code for a work means the preferred form of the work for
+making modifications to it.  For an executable work, complete source
+code means all the source code for all modules it contains, plus any
+associated interface definition files, plus the scripts used to
+control compilation and installation of the executable.  However, as a
+special exception, the source code distributed need not include
+anything that is normally distributed (in either source or binary
+form) with the major components (compiler, kernel, and so on) of the
+operating system on which the executable runs, unless that component
+itself accompanies the executable.
+
+If distribution of executable or object code is made by offering
+access to copy from a designated place, then offering equivalent
+access to copy the source code from the same place counts as
+distribution of the source code, even though third parties are not
+compelled to copy the source along with the object code.
+
+  4. You may not copy, modify, sublicense, or distribute the Program
+except as expressly provided under this License.  Any attempt
+otherwise to copy, modify, sublicense or distribute the Program is
+void, and will automatically terminate your rights under this License.
+However, parties who have received copies, or rights, from you under
+this License will not have their licenses terminated so long as such
+parties remain in full compliance.
+
+  5. You are not required to accept this License, since you have not
+signed it.  However, nothing else grants you permission to modify or
+distribute the Program or its derivative works.  These actions are
+prohibited by law if you do not accept this License.  Therefore, by
+modifying or distributing the Program (or any work based on the
+Program), you indicate your acceptance of this License to do so, and
+all its terms and conditions for copying, distributing or modifying
+the Program or works based on it.
+
+  6. Each time you redistribute the Program (or any work based on the
+Program), the recipient automatically receives a license from the
+original licensor to copy, distribute or modify the Program subject to
+these terms and conditions.  You may not impose any further
+restrictions on the recipients' exercise of the rights granted herein.
+You are not responsible for enforcing compliance by third parties to
+this License.
+
+  7. If, as a consequence of a court judgment or allegation of patent
+infringement or for any other reason (not limited to patent issues),
+conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License.  If you cannot
+distribute so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you
+may not distribute the Program at all.  For example, if a patent
+license would not permit royalty-free redistribution of the Program by
+all those who receive copies directly or indirectly through you, then
+the only way you could satisfy both it and this License would be to
+refrain entirely from distribution of the Program.
+
+If any portion of this section is held invalid or unenforceable under
+any particular circumstance, the balance of the section is intended to
+apply and the section as a whole is intended to apply in other
+circumstances.
+
+It is not the purpose of this section to induce you to infringe any
+patents or other property right claims or to contest validity of any
+such claims; this section has the sole purpose of protecting the
+integrity of the free software distribution system, which is
+implemented by public license practices.  Many people have made
+generous contributions to the wide range of software distributed
+through that system in reliance on consistent application of that
+system; it is up to the author/donor to decide if he or she is willing
+to distribute software through any other system and a licensee cannot
+impose that choice.
+
+This section is intended to make thoroughly clear what is believed to
+be a consequence of the rest of this License.
+
+  8. If the distribution and/or use of the Program is restricted in
+certain countries either by patents or by copyrighted interfaces, the
+original copyright holder who places the Program under this License
+may add an explicit geographical distribution limitation excluding
+those countries, so that distribution is permitted only in or among
+countries not thus excluded.  In such case, this License incorporates
+the limitation as if written in the body of this License.
+
+  9. The Free Software Foundation may publish revised and/or new versions
+of the General Public License from time to time.  Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+Each version is given a distinguishing version number.  If the Program
+specifies a version number of this License which applies to it and "any
+later version", you have the option of following the terms and conditions
+either of that version or of any later version published by the Free
+Software Foundation.  If the Program does not specify a version number of
+this License, you may choose any version ever published by the Free Software
+Foundation.
+
+  10. If you wish to incorporate parts of the Program into other free
+programs whose distribution conditions are different, write to the author
+to ask for permission.  For software which is copyrighted by the Free
+Software Foundation, write to the Free Software Foundation; we sometimes
+make exceptions for this.  Our decision will be guided by the two goals
+of preserving the free status of all derivatives of our free software and
+of promoting the sharing and reuse of software generally.
+
+			    NO WARRANTY
+
+  11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
+FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.  EXCEPT WHEN
+OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
+PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
+OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRE RISK AS
+TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.  SHOULD THE
+PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
+REPAIR OR CORRECTION.
+
+  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
+REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
+INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
+OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
+TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
+YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
+PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGES.
+
+		     END OF TERMS AND CONDITIONS
+
+	    How to Apply These Terms to Your New Programs
+
+  If you develop a new program, and you want it to be of the greatest
+possible use to the public, the best way to achieve this is to make it
+free software which everyone can redistribute and change under these terms.
+
+  To do so, attach the following notices to the program.  It is safest
+to attach them to the start of each source file to most effectively
+convey the exclusion of warranty; and each file should have at least
+the "copyright" line and a pointer to where the full notice is found.
+
+    <one line to give the program's name and a brief idea of what it does.>
+    Copyright (C) <year>  <name of author>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+Also add information on how to contact you by electronic and paper mail.
+
+If the program is interactive, make it output a short notice like this
+when it starts in an interactive mode:
+
+    Gnomovision version 69, Copyright (C) year name of author
+    Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
+    This is free software, and you are welcome to redistribute it
+    under certain conditions; type `show c' for details.
+
+The hypothetical commands `show w' and `show c' should show the appropriate
+parts of the General Public License.  Of course, the commands you use may
+be called something other than `show w' and `show c'; they could even be
+mouse-clicks or menu items--whatever suits your program.
+
+You should also get your employer (if you work as a programmer) or your
+school, if any, to sign a "copyright disclaimer" for the program, if
+necessary.  Here is a sample; alter the names:
+
+  Yoyodyne, Inc., hereby disclaims all copyright interest in the program
+  `Gnomovision' (which makes passes at compilers) written by James Hacker.
+
+  <signature of Ty Coon>, 1 April 1989
+  Ty Coon, President of Vice
+
+This General Public License does not permit incorporating your program into
+proprietary programs.  If your program is a subroutine library, you may
+consider it more useful to permit linking proprietary applications with the
+library.  If this is what you want to do, use the GNU Library General
+Public License instead of this License.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/Makefile
@@ -0,0 +1,25 @@
+SRC := $(shell pwd)
+
+ifeq ($(O),)
+	include $(KERNEL_SRC)/.config
+else
+	include $(O)/.config
+endif
+
+obj-m	+= common/
+obj-m	+= al5e/
+obj-m	+= al5d/
+obj-m	+= dmaproxy/
+
+all:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) O=$(O) modules
+
+modules_install:
+	$(MAKE) -C $(KERNEL_SRC) M=$(SRC) modules_install
+
+clean:
+	rm -f *.o *~ core .depend .*.cmd *.ko *.mod.c
+	rm -f Module.markers Module.symvers modules.order modules.builtin
+	rm -f */*.ko */*.mod.c */.*.mod.c */.*.cmd */*.o
+	rm -f */modules.order */modules.builtin
+	rm -rf .tmp_versions Modules.symvers
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/README.md
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/README.md
@@ -0,0 +1 @@
+Video Codec Unit (VCU) Linux out-of-tree modules for Yocto.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/Kconfig
@@ -0,0 +1,8 @@
+config ALLEGRO_VCU_DEC_DRIVER
+    tristate "Allegro VCU Decoder"
+    depends on HAS_DMA
+    select DMA_SHARED_BUFFER
+    help
+        Enables Allegro VCU driver.
+        To compile this driver as a module, choose M here.
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/Makefile
@@ -0,0 +1,10 @@
+AL_COMMON=../common
+
+ccflags-y += -I$(srctree)/$(src)/../include
+
+obj-m += al5d.o
+
+al5d-objs := \
+	al_dec.o \
+	dec_mails_factory.o \
+	dec_user.o \
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/al_dec.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/al_dec.c
@@ -0,0 +1,369 @@
+/*
+ * al_dec.c userspace interface and probe / remove of the driver
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/io.h>
+#include <linux/uaccess.h>
+
+#include <linux/cdev.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/fcntl.h>
+#include <linux/firmware.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/signal.h>
+#include <linux/slab.h>
+#include <linux/stddef.h>
+#include <linux/vmalloc.h>
+#include <linux/version.h>
+
+#include "al_dec_ioctl.h"
+#include "al_alloc_ioctl.h"
+#include "al_vcu.h"
+#include "al_alloc.h"
+#include "al_user.h"
+#include "al_codec.h"
+#include "dec_user.h"
+#include "al_char.h"
+
+#include "mcu_interface.h"
+#include "al_mail.h"
+#include "dec_mails_factory.h"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+#include "xil_clk.h"
+#endif
+
+#define AL5D_FIRMWARE "al5d.fw"
+#define AL5D_BOOTLOADER_FIRMWARE "al5d_b.fw"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+#define AL5D_CORE_CLK "vcu_core_dec"
+#define AL5D_MCU_CLK "vcu_mcu_dec"
+#endif
+
+int max_users_nb = MAX_USERS_NB;
+static int al5d_codec_major;
+static int al5d_codec_nr_devs = AL5_NR_DEVS;
+static struct class *module_class;
+
+static int ioctl_usage(struct al5_user *user, unsigned int cmd)
+{
+	pr_err("Unknown ioctl: 0x%.8X\n", cmd);
+	pr_err("Known ioctl are:\n");
+	pr_err("AL_MCU_CONFIG_CHANNEL:%.8lX\n",
+	       (unsigned long)AL_MCU_CONFIG_CHANNEL);
+	pr_err("AL_MCU_DESTROY_CHANNEL:%.8lX\n",
+	       (unsigned long)AL_MCU_DESTROY_CHANNEL);
+	pr_err("AL_MCU_DECODE_ONE_FRM:%.8lX\n",
+	       (unsigned long)AL_MCU_DECODE_ONE_FRM);
+	pr_err("AL_MCU_WAIT_FOR_STATUS:%.8lX\n",
+	       (unsigned long)AL_MCU_WAIT_FOR_STATUS);
+	pr_err("AL_MCU_SEARCH_START_CODE:%.8lX\n",
+	       (unsigned long)AL_MCU_SEARCH_START_CODE);
+	pr_err("GET_DMA_FD:%.8lX\n",
+	       (unsigned long)GET_DMA_FD);
+
+	return -EINVAL;
+}
+
+static long al5d_ioctl(struct file *filp, unsigned int cmd,
+		       unsigned long arg)
+{
+	struct al5_filp_data *filp_data = filp->private_data;
+	struct al5_user *user = filp_data->user;
+	struct al5_codec_desc *codec = filp_data->codec;
+	long ret;
+
+	switch (cmd) {
+		struct al5_channel_config channel_config;
+		struct al5_params params;
+		struct al5_decode_msg decode_msg;
+		struct al5_search_sc_msg sc_msg;
+		struct al5_scstatus sc_status;
+	case AL_MCU_CONFIG_CHANNEL:
+		ioctl_info("ioctl AL_MCU_CONFIG_CHANNEL from user %i",
+			   user->uid);
+		if (copy_from_user(&channel_config, (void *)arg,
+				   sizeof(channel_config)))
+			return -EFAULT;
+		ret = al5d_user_create_channel(user, &channel_config);
+		if (copy_to_user((void *)arg, &channel_config,
+				 sizeof(channel_config)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_CONFIG_CHANNEL for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_DESTROY_CHANNEL:
+		ioctl_info("ioctl AL_MCU_DESTROY_CHANNEL from user %i",
+			   user->uid);
+		ret = al5_user_destroy_channel(user, false);
+		ioctl_info("end AL_MCU_DESTROY_CHANNEL for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_WAIT_FOR_STATUS:
+		ioctl_info("ioctl AL_MCU_WAIT_FOR_STATUS from user %i",
+			   user->uid);
+		if (copy_from_user(&params, (void *)arg, sizeof(params)))
+			return -EFAULT;
+		ret = al5d_user_wait_for_status(user, &params);
+		if (copy_to_user((void *)arg, &params, sizeof(params)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_WAIT_FOR_STATUS for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_DECODE_ONE_FRM:
+		ioctl_info("ioctl AL_MCU_DECODE_ONE_FRM from user %i",
+			   user->uid);
+		if (copy_from_user(&decode_msg, (void *)arg,
+				   sizeof(decode_msg)))
+			return -EFAULT;
+		ret = al5d_user_decode_one_frame(user, &decode_msg);
+		if (copy_to_user((void *)arg, &decode_msg, sizeof(decode_msg)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_DECODE_ONE_FRM for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_DECODE_ONE_SLICE:
+		ioctl_info("ioctl AL_MCU_DECODE_ONE_SLICE from user %i",
+			   user->uid);
+		if (copy_from_user(&decode_msg, (void *)arg,
+				   sizeof(decode_msg)))
+			return -EFAULT;
+		ret = al5d_user_decode_one_slice(user, &decode_msg);
+		if (copy_to_user((void *)arg, &decode_msg, sizeof(decode_msg)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_DECODE_ONE_SLICE for user %i",
+			   user->uid);
+		return ret;
+
+	case AL_MCU_SEARCH_START_CODE:
+		ioctl_info("ioctl AL_MCU_SEARCH_START_CODE from user %i",
+			   user->uid);
+		if (copy_from_user(&sc_msg, (void *)arg, sizeof(sc_msg)))
+			return -EFAULT;
+		ret = al5d_user_search_start_code(user, &sc_msg);
+		if (copy_to_user((void *)arg, &sc_msg, sizeof(sc_msg)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_SEARCH_START_CODE for user %i",
+			   user->uid);
+		return ret;
+
+	case AL_MCU_WAIT_FOR_START_CODE:
+		ioctl_info("ioctl AL_MCU_WAIT_FOR_START_CODE from user %i",
+			   user->uid);
+		if (copy_from_user(&sc_status, (void *)arg, sizeof(sc_status)))
+			return -EFAULT;
+		ret = al5d_user_wait_for_start_code(user, &sc_status);
+		if (copy_to_user((void *)arg, &sc_status, sizeof(sc_status)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_WAIT_FOR_START_CODE for user %i",
+			   user->uid);
+		return ret;
+
+	case GET_DMA_FD:
+		ret = al5_ioctl_get_dma_fd(codec->device, arg);
+		return ret;
+
+	case GET_DMA_PHY:
+		ret = al5_ioctl_get_dmabuf_dma_addr(codec->device, arg);
+		return ret;
+
+	default:
+		return ioctl_usage(user, cmd);
+	}
+
+	return 0;
+}
+
+static const struct file_operations al5d_fops = {
+	.owner		= THIS_MODULE,
+	.open		= al5_codec_open,
+	.release	= al5_codec_release,
+	.unlocked_ioctl = al5d_ioctl,
+	.compat_ioctl	= al5_codec_compat_ioctl,
+	.poll		= al5_codec_poll,
+};
+
+static int al5d_setup_codec_cdev(struct al5_codec_desc *codec, int minor)
+{
+	struct device *device;
+	const char *device_name = "allegroDecodeIP";
+	dev_t dev = MKDEV(al5d_codec_major, minor);
+
+	int err = al5_setup_codec_cdev(codec, &al5d_fops, THIS_MODULE,
+				       al5d_codec_major,
+				       minor);
+
+	if (err)
+		return err;
+
+	of_property_read_string(codec->device->of_node, "al,devicename", &device_name);
+
+	device = device_create(module_class, NULL, dev, NULL, device_name);
+	if (IS_ERR(device)) {
+		pr_err("device not created\n");
+		al5_clean_up_codec_cdev(codec);
+		return PTR_ERR(device);
+	}
+
+	return 0;
+}
+
+static int al5d_codec_probe(struct platform_device *pdev)
+{
+	int err;
+	static int current_minor;
+
+	struct al5_codec_desc *codec;
+
+	codec = devm_kzalloc(&pdev->dev,
+			     sizeof(struct al5_codec_desc),
+			     GFP_KERNEL);
+	if (codec == NULL)
+		return -ENOMEM;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+	err = xil_clk_set_up(pdev, codec, AL5D_CORE_CLK, AL5D_MCU_CLK);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup clock");
+		return err;
+	}
+#endif
+
+	err = al5_codec_set_up(codec, pdev, max_users_nb);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup codec");
+		return err;
+	}
+	err = al5_codec_set_firmware(codec, AL5D_FIRMWARE,
+				     AL5D_BOOTLOADER_FIRMWARE);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup firmware");
+		al5_codec_tear_down(codec);
+		return err;
+	}
+	err = al5d_setup_codec_cdev(codec, current_minor);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup cdev");
+		al5_codec_tear_down(codec);
+		return err;
+	}
+	codec->minor = current_minor;
+	++current_minor;
+
+	return 0;
+}
+
+static int al5d_codec_remove(struct platform_device *pdev)
+{
+	struct al5_codec_desc *codec = platform_get_drvdata(pdev);
+	dev_t dev = MKDEV(al5d_codec_major, codec->minor);
+
+	al5_codec_tear_down(codec);
+	device_destroy(module_class, dev);
+	al5_clean_up_codec_cdev(codec);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+	xil_clk_clean_up(pdev, codec);
+#endif
+	return 0;
+}
+
+static const struct of_device_id al5d_codec_of_match[] = {
+	{ .compatible = "al,al5d" },
+	{ /* sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, al5d_codec_of_match);
+
+static struct platform_driver al5d_platform_driver = {
+	.probe			= al5d_codec_probe,
+	.remove			= al5d_codec_remove,
+	.driver			=       {
+		.name		= "al5d",
+		.of_match_table = of_match_ptr(al5d_codec_of_match),
+	},
+};
+
+static int setup_chrdev_region(void)
+{
+	return al5_setup_chrdev_region(&al5d_codec_major, 0,
+				       al5d_codec_nr_devs, "al5d");
+}
+
+static int create_module_class(void)
+{
+	module_class = class_create(THIS_MODULE, "allegro_decode_class");
+	if (IS_ERR(module_class))
+		return PTR_ERR(module_class);
+
+	return 0;
+}
+
+static void destroy_module_class(void)
+{
+	class_destroy(module_class);
+}
+
+static int __init al5d_codec_init(void)
+{
+	int err;
+
+	err = setup_chrdev_region();
+	if (err)
+		return err;
+
+	err = create_module_class();
+	if (err)
+		return err;
+
+	return platform_driver_register(&al5d_platform_driver);
+}
+
+static void __exit al5d_codec_exit(void)
+{
+	dev_t devno = MKDEV(al5d_codec_major, 0);
+
+	platform_driver_unregister(&al5d_platform_driver);
+	destroy_module_class();
+	unregister_chrdev_region(devno, al5d_codec_nr_devs);
+}
+
+module_init(al5d_codec_init);
+module_exit(al5d_codec_exit);
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Kevin Grandemange");
+MODULE_AUTHOR("Sebastien Alaiwan");
+MODULE_AUTHOR("Antoine Gruzelle");
+MODULE_DESCRIPTION("Allegro Codec Driver");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/al_dec_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/al_dec_ioctl.h
@@ -0,0 +1,62 @@
+/*
+ * al_dec_ioctl.h structure used to communicate with the userspace
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_DEC_IOCTL_H_
+#define _AL_DEC_IOCTL_H_
+#include <linux/types.h>
+#include "al_ioctl.h"
+
+#define AL_MCU_CONFIG_CHANNEL  _IOWR('q', 2, struct al5_channel_config)
+#define AL_MCU_DESTROY_CHANNEL  _IO('q', 4)
+#define AL_MCU_DECODE_ONE_FRM _IOWR('q', 5, struct al5_decode_msg)
+#define AL_MCU_WAIT_FOR_STATUS _IOWR('q', 6, struct al5_params)
+#define AL_MCU_SEARCH_START_CODE _IOWR('q', 8, struct al5_search_sc_msg)
+#define AL_MCU_WAIT_FOR_START_CODE _IOWR('q', 9, struct al5_scstatus)
+#define AL_MCU_DECODE_ONE_SLICE _IOWR('q', 18, struct al5_decode_msg)
+
+struct al5_channel_status {
+	__u32 error_code;
+};
+
+struct al5_params {
+	__u32 size;
+	__u32 opaque[128];
+};
+
+struct al5_channel_config {
+	struct al5_params param;
+	struct al5_channel_status status;
+};
+
+struct al5_scstatus {
+	__u16 num_sc;
+	__u32 num_bytes;
+};
+
+struct al5_decode_msg {
+	struct al5_params params;
+	struct al5_params addresses;
+	__u32 slice_param_v;
+};
+
+struct al5_search_sc_msg {
+	struct al5_params param;
+	struct al5_params buffer_addrs;
+};
+
+#endif  /* _AL_DEC_IOCTL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/dec_mails_factory.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/dec_mails_factory.c
@@ -0,0 +1,102 @@
+/*
+ * dec_mails_factory.c high level message creation for the mcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/device.h>
+#include <linux/string.h>
+
+#include "al_mail.h"
+#include "al_mail_private.h"
+#include "al_codec_mails.h"
+#include "dec_mails_factory.h"
+
+const u32 sender_uid_size = 4;
+
+/* *msg is filled, *mail is read-only */
+void al5d_mail_get_status(struct al5_params *status, struct al5_mail *mail)
+{
+	status->size = mail->body_size - 4;
+	memcpy(&status->opaque, mail->body + 4, status->size);
+}
+
+/* *msg is filled, *mail is read-only */
+void al5d_mail_get_sc_status(struct al5_scstatus *scstatus,
+			     struct al5_mail *mail)
+{
+	memcpy(scstatus, mail->body + 4, sizeof(*scstatus));
+}
+
+void write_decode_mail(struct al5_mail *mail,
+		       u32 chan_uid, struct al5_decode_msg *msg)
+{
+	al5_mail_write_word(mail, chan_uid);
+	al5_mail_write(mail, msg->params.opaque, msg->params.size);
+	al5_mail_write(mail, msg->addresses.opaque, msg->addresses.size);
+	al5_mail_write_word(mail, msg->slice_param_v);
+}
+
+struct al5_mail *
+al5d_create_decode_one_slice_msg(u32 chan_uid, struct al5_decode_msg *msg)
+{
+	int mail_size = 4 + msg->params.size + msg->addresses.size +
+			sizeof(msg->slice_param_v);
+	struct al5_mail *mail = al5_mail_create(AL_MCU_MSG_DECODE_ONE_SLICE,
+						mail_size);
+
+	write_decode_mail(mail, chan_uid, msg);
+
+	return mail;
+}
+
+struct al5_mail *
+al5d_create_decode_one_frame_msg(u32 chan_uid, struct al5_decode_msg *msg)
+{
+	int mail_size = 4 + msg->params.size + msg->addresses.size +
+			sizeof(msg->slice_param_v);
+	struct al5_mail *mail = al5_mail_create(AL_MCU_MSG_DECODE_ONE_FRM,
+						mail_size);
+
+	write_decode_mail(mail, chan_uid, msg);
+
+	return mail;
+}
+
+struct al5_mail *
+al5d_create_channel_param_msg(u32 user_uid, struct al5_params *msg)
+{
+	int mail_size = 4 + msg->size;
+	struct al5_mail *mail = al5_mail_create(AL_MCU_MSG_CREATE_CHANNEL,
+						mail_size);
+
+	al5_mail_write_word(mail, user_uid);
+	al5_mail_write(mail, msg->opaque, msg->size);
+	return mail;
+}
+
+struct al5_mail *
+al5d_create_search_sc_mail(u32 user_uid, struct al5_search_sc_msg *msg)
+{
+	int mail_size = 4 + msg->param.size + msg->buffer_addrs.size;
+	struct al5_mail *mail = al5_mail_create(AL_MCU_MSG_SEARCH_START_CODE,
+						mail_size);
+
+	al5_mail_write_word(mail, user_uid);
+	al5_mail_write(mail, msg->param.opaque, msg->param.size);
+	al5_mail_write(mail, msg->buffer_addrs.opaque, msg->buffer_addrs.size);
+
+	return mail;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/dec_mails_factory.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/dec_mails_factory.h
@@ -0,0 +1,39 @@
+/*
+ * dec_mails_factory.h high level message creation for the mcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _MCU_DEC_H_
+#define _MCU_DEC_H_
+
+#include "mcu_interface.h"
+#include "al_mail.h"
+#include "al_dec_ioctl.h"
+
+void al5d_mail_get_status(struct al5_params *status, struct al5_mail *mail);
+void al5d_mail_get_sc_status(struct al5_scstatus *scstatus,
+			     struct al5_mail *mail);
+
+struct al5_mail *al5d_create_decode_one_frame_msg(u32 chan_uid,
+						  struct al5_decode_msg *msg);
+struct al5_mail *al5d_create_channel_param_msg(u32 user_uid,
+					       struct al5_params *msg);
+struct al5_mail *al5d_create_search_sc_mail(u32 user_uid,
+					    struct al5_search_sc_msg *msg);
+struct al5_mail *al5d_create_decode_one_slice_msg(u32 chan_uid,
+						  struct al5_decode_msg *msg);
+
+#endif /* _MCU_DEC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/dec_user.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/dec_user.c
@@ -0,0 +1,219 @@
+/*
+ * dec_user.c high level communication with the vcu and the firmware
+ * channel creation, frame encoding
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/printk.h>
+#include <linux/string.h>
+
+#include "dec_user.h"
+#include "dec_mails_factory.h"
+#include "al_mail.h"
+#include "al_mail_private.h"
+#include "al_codec_mails.h"
+
+static void update_chan_param(struct al5_channel_status *status,
+			      struct al5_mail *mail)
+{
+	memcpy(&status->error_code, mail->body + 8, 4);
+}
+
+static int chan_is_valid(u32 chan_uid)
+{
+	return chan_uid == BAD_CHAN ? -EINVAL : 0;
+}
+
+static int check_chan_id(struct al5_user *user, struct al5_mail *mail)
+{
+	u32 chan_uid = al5_mail_get_chan_uid(mail);
+
+	if (chan_is_valid(chan_uid)) {
+		dev_err(user->device,
+			"VCU: unavailable resources or wrong configuration");
+		return -EINVAL;
+	}
+	return 0;
+}
+
+int al5d_user_create_channel(struct al5_user *user,
+			     struct al5_channel_config *msg)
+{
+	struct al5_mail *feedback;
+	int err = -EINVAL;
+
+	err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+	if (err == -EINTR)
+		return err;
+
+	if (al5_chan_is_created(user)) {
+		err = -EPERM;
+		goto unlock;
+	}
+
+	err = al5_check_and_send(user,
+				 al5d_create_channel_param_msg(user->uid,
+							       &msg->param));
+	if (err)
+		goto unlock;
+
+	err =
+		al5_queue_pop_timeout(&feedback,
+				      &user->queues[AL5_USER_MAIL_CREATE]);
+	if (err)
+		goto unlock;
+
+	update_chan_param(&msg->status, feedback);
+
+	err = check_chan_id(user, feedback);
+	al5_free_mail(feedback);
+	if (err)
+		goto unlock;
+
+	user->checkpoint = CHECKPOINT_CREATED;
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return 0;
+
+unlock:
+	dev_err(user->device, "Channel wasn't created.");
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5d_user_create_channel);
+
+int al5d_user_decode_one_slice(struct al5_user *user,
+			       struct al5_decode_msg *msg)
+{
+	int err;
+
+	err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+	if (err == -EINTR)
+		return err;
+
+	if (!al5_chan_is_created(user)) {
+		dev_err(user->device,
+			"Cannot decode slice until channel is configured on MCU");
+		err = -EPERM;
+		goto unlock;
+	}
+
+	err = al5_check_and_send(user,
+				 al5d_create_decode_one_slice_msg(user->chan_uid,
+								  msg));
+
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+
+int al5d_user_decode_one_frame(struct al5_user *user,
+			       struct al5_decode_msg *msg)
+{
+	int err;
+
+	err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+	if (err == -EINTR)
+		return err;
+
+	if (!al5_chan_is_created(user)) {
+		dev_err(user->device,
+			"Cannot decode frame until channel is configured on MCU");
+		err = -EPERM;
+		goto unlock;
+	}
+
+	err = al5_check_and_send(user,
+				 al5d_create_decode_one_frame_msg(user->chan_uid,
+								  msg));
+
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+
+}
+EXPORT_SYMBOL_GPL(al5d_user_decode_one_frame);
+
+int al5d_user_search_start_code(struct al5_user *user,
+				struct al5_search_sc_msg *msg)
+{
+	return al5_check_and_send(user,
+				  al5d_create_search_sc_mail(user->uid, msg));
+}
+EXPORT_SYMBOL_GPL(al5d_user_search_start_code);
+
+int al5d_user_wait_for_status(struct al5_user *user, struct al5_params *msg)
+{
+	struct al5_mail *feedback;
+	int err = 0;
+
+	if (!mutex_trylock(&user->locks[AL5_USER_STATUS]))
+		return -EINTR;
+
+	if (!al5_chan_is_created(user)) {
+		err = -EPERM;
+		goto unlock;
+	}
+
+	if (user->non_block) {
+		feedback = al5_queue_pop_no_wait(&user->queues[AL5_USER_MAIL_STATUS]);
+		if (feedback)
+			al5d_mail_get_status(msg, feedback);
+		else
+			err = -EWOULDBLOCK;
+	}else  {
+		feedback = al5_queue_pop(&user->queues[AL5_USER_MAIL_STATUS]);
+		if (feedback)
+			al5d_mail_get_status(msg, feedback);
+		else
+			err = -EINTR;
+	}
+
+	al5_free_mail(feedback);
+
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_STATUS]);
+	return err;
+}
+
+int al5d_user_wait_for_start_code(struct al5_user *user,
+				  struct al5_scstatus *msg)
+{
+	int err = 0;
+	struct al5_mail *feedback;
+
+	if (!mutex_trylock(&user->locks[AL5_USER_SC]))
+		return -EINTR;
+
+	if (user->non_block) {
+		feedback = al5_queue_pop_no_wait(&user->queues[AL5_USER_MAIL_SC]);
+		if (feedback)
+			al5d_mail_get_sc_status(msg, feedback);
+		else
+			err = -EWOULDBLOCK;
+	}else  {
+		feedback = al5_queue_pop(&user->queues[AL5_USER_MAIL_SC]);
+		if (feedback)
+			al5d_mail_get_sc_status(msg, feedback);
+		else
+			err = -EINTR;
+	}
+
+	al5_free_mail(feedback);
+
+	mutex_unlock(&user->locks[AL5_USER_SC]);
+	return err;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5d/dec_user.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5d/dec_user.h
@@ -0,0 +1,33 @@
+/*
+ * dec_user.h high level communication with the vcu and the firmware
+ * channel creation, frame encoding
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "al_user.h"
+#include "al_dec_ioctl.h"
+
+int al5d_user_create_channel(struct al5_user *user,
+			     struct al5_channel_config *msg);
+int al5d_user_decode_one_frame(struct al5_user *user,
+			       struct al5_decode_msg *msg);
+int al5d_user_search_start_code(struct al5_user *user,
+				struct al5_search_sc_msg *msg);
+int al5d_user_wait_for_status(struct al5_user *user, struct al5_params *msg);
+int al5d_user_wait_for_start_code(struct al5_user *user,
+				  struct al5_scstatus *msg);
+int al5d_user_decode_one_slice(struct al5_user *user,
+			       struct al5_decode_msg *msg);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/Kconfig
@@ -0,0 +1,8 @@
+config ALLEGRO_VCU_ENC_DRIVER
+    tristate "Allegro VCU Encoder"
+    depends on HAS_DMA
+    select DMA_SHARED_BUFFER
+    help
+        Enables Allegro VCU Encoder driver.
+        To compile this driver as a module, choose M here.
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/Makefile
@@ -0,0 +1,10 @@
+AL_COMMON=../common
+
+ccflags-y += -I$(srctree)/$(src)/../include
+
+obj-m += al5e.o
+
+al5e-objs := \
+	al_enc.o\
+	enc_user.o\
+	enc_mails_factory.o\
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/al_enc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/al_enc.c
@@ -0,0 +1,355 @@
+/*
+ * al_enc.c userspace interface and probe / remove of the driver
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/io.h>
+#include <linux/uaccess.h>
+
+#include <linux/cdev.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/fcntl.h>
+#include <linux/firmware.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/signal.h>
+#include <linux/slab.h>
+#include <linux/stddef.h>
+#include <linux/vmalloc.h>
+#include <linux/version.h>
+
+#include "al_enc_ioctl.h"
+#include "al_alloc_ioctl.h"
+#include "al_vcu.h"
+#include "al_alloc.h"
+#include "al_user.h"
+#include "al_codec.h"
+#include "enc_user.h"
+#include "al_char.h"
+
+#include "mcu_interface.h"
+#include "al_mail.h"
+#include "enc_mails_factory.h"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+#include "xil_clk.h"
+#endif
+
+#define AL5E_FIRMWARE "al5e.fw"
+#define AL5E_BOOTLOADER_FIRMWARE "al5e_b.fw"
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+#define AL5E_CORE_CLK "vcu_core_enc"
+#define AL5E_MCU_CLK "vcu_mcu_enc"
+#endif
+
+int max_users_nb = MAX_USERS_NB;
+static int al5e_codec_major;
+static int al5e_codec_nr_devs = AL5_NR_DEVS;
+static struct class *module_class;
+
+static int ioctl_usage(struct al5_user *user, unsigned int cmd)
+{
+	pr_err("Unknown ioctl: 0x%.8X\n", cmd);
+	pr_err("Known ioctl are:\n");
+	pr_err("AL_MCU_CONFIG_CHANNEL:%.8lX\n",
+	       (unsigned long)AL_MCU_CONFIG_CHANNEL);
+	pr_err("AL_MCU_DESTROY_CHANNEL:%.8lX\n",
+	       (unsigned long)AL_MCU_DESTROY_CHANNEL);
+	pr_err("AL_MCU_ENCODE_ONE_FRM:%.8lX\n",
+	       (unsigned long)AL_MCU_ENCODE_ONE_FRM);
+	pr_err("AL_MCU_WAIT_FOR_STATUS:%.8lX\n",
+	       (unsigned long)AL_MCU_WAIT_FOR_STATUS);
+	pr_err("GET_DMA_FD:%.8lX\n",
+	       (unsigned long)GET_DMA_FD);
+
+	return -EINVAL;
+}
+
+static long al5e_ioctl(struct file *filp, unsigned int cmd,
+		       unsigned long arg)
+{
+	struct al5_filp_data *filp_data = filp->private_data;
+	struct al5_user *user = filp_data->user;
+	struct al5_codec_desc *codec = filp_data->codec;
+	long ret;
+
+	switch (cmd) {
+		struct al5_config_channel config_channel;
+		struct al5_params encode_status;
+		struct al5_encode_msg encode_msg;
+		struct al5_reconstructed_info rec_msg;
+		struct al5_buffer buffer_msg;
+		u32 rec_fd;
+	case AL_MCU_CONFIG_CHANNEL:
+		ioctl_info("ioctl AL_MCU_CONFIG_CHANNEL from user %i",
+			   user->uid);
+		if (copy_from_user(&config_channel, (void *)arg,
+				   sizeof(config_channel)))
+			return -EFAULT;
+		ret = al5e_user_create_channel(user, &config_channel);
+		if (copy_to_user((void *)arg, &config_channel,
+				 sizeof(config_channel)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_CONFIG_CHANNEL for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_DESTROY_CHANNEL:
+		ioctl_info("ioctl AL_MCU_DESTROY_CHANNEL from user %i",
+			   user->uid);
+		ret = al5_user_destroy_channel(user, false);
+		ioctl_info("end AL_MCU_DESTROY_CHANNEL for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_WAIT_FOR_STATUS:
+		ioctl_info("ioctl AL_MCU_WAIT_FOR_STATUS from user %i",
+			   user->uid);
+		if (copy_from_user(&encode_status, (void *)arg,
+				   sizeof(encode_status)))
+			return -EFAULT;
+		ret = al5e_user_wait_for_status(user, &encode_status);
+		if (copy_to_user((void *)arg, &encode_status,
+				 sizeof(encode_status)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_WAIT_FOR_STATUS for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_ENCODE_ONE_FRM:
+		ioctl_info("ioctl AL_MCU_ENCODE_ONE_FRM from user %i",
+			   user->uid);
+		if (copy_from_user(&encode_msg, (void *)arg,
+				   sizeof(encode_msg)))
+			return -EFAULT;
+		ret = al5e_user_encode_one_frame(user, &encode_msg);
+		if (copy_to_user((void *)arg, &encode_msg, sizeof(encode_msg)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_ENCODE_ONE_FRM for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_GET_REC_PICTURE:
+		ioctl_info("ioctl AL_MCU_GET_REC from user %i", user->uid);
+		if (copy_from_user(&rec_msg, (void *)arg, sizeof(rec_msg)))
+			return -EFAULT;
+		ret = al5e_user_get_rec(user, &rec_msg);
+		if (copy_to_user((void *)arg, &rec_msg, sizeof(rec_msg)))
+			return -EFAULT;
+		ioctl_info("end AL_MCU_GET_REC for user %i", user->uid);
+		return ret;
+
+	case AL_MCU_RELEASE_REC_PICTURE:
+		ioctl_info("ioctl AL_MCU_GET_REC from user %i", user->uid);
+		if (copy_from_user(&rec_fd, (void *)arg, sizeof(rec_fd)))
+			return -EFAULT;
+		return al5e_user_release_rec(user, rec_fd);
+		ioctl_info("end AL_MCU_GET_REC from user %i", user->uid);
+
+	case AL_MCU_PUT_STREAM_BUFFER:
+		if (copy_from_user(&buffer_msg, (void *)arg,
+				   sizeof(buffer_msg)))
+			return -EFAULT;
+		return al5e_user_put_stream_buffer(user, &buffer_msg);
+
+	case GET_DMA_FD:
+		ret = al5_ioctl_get_dma_fd(codec->device, arg);
+		return ret;
+
+	case GET_DMA_PHY:
+		ret = al5_ioctl_get_dmabuf_dma_addr(codec->device, arg);
+		return ret;
+
+	default:
+		return ioctl_usage(user, cmd);
+	}
+}
+
+static const struct file_operations al5e_fops = {
+	.owner		= THIS_MODULE,
+	.open		= al5_codec_open,
+	.release	= al5_codec_release,
+	.unlocked_ioctl = al5e_ioctl,
+	.compat_ioctl	= al5_codec_compat_ioctl,
+	.poll		= al5_codec_poll,
+};
+
+static int al5e_setup_codec_cdev(struct al5_codec_desc *codec, int minor)
+{
+	struct device *device;
+	const char *device_name = "allegroIP";
+	dev_t dev = MKDEV(al5e_codec_major, minor);
+
+	int err = al5_setup_codec_cdev(codec, &al5e_fops, THIS_MODULE,
+				       al5e_codec_major,
+				       minor);
+
+	if (err)
+		return err;
+
+	of_property_read_string(codec->device->of_node, "al,devicename", &device_name);
+
+	device = device_create(module_class, NULL, dev, NULL, device_name);
+	if (IS_ERR(device)) {
+		pr_err("device not created\n");
+		al5_clean_up_codec_cdev(codec);
+		return PTR_ERR(device);
+	}
+
+	return 0;
+}
+
+static int al5e_probe(struct platform_device *pdev)
+{
+	int err;
+	static int current_minor;
+
+	struct al5_codec_desc *codec;
+
+	codec = devm_kzalloc(&pdev->dev,
+			     sizeof(struct al5_codec_desc),
+			     GFP_KERNEL);
+	if (codec == NULL)
+		return -ENOMEM;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+	err = xil_clk_set_up(pdev, codec, AL5E_CORE_CLK, AL5E_MCU_CLK);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup clock");
+		return err;
+	}
+#endif
+
+	err = al5_codec_set_up(codec, pdev, max_users_nb);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup codec");
+		return err;
+	}
+	err = al5_codec_set_firmware(codec, AL5E_FIRMWARE,
+				     AL5E_BOOTLOADER_FIRMWARE);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup firmware");
+		al5_codec_tear_down(codec);
+		return err;
+	}
+	err = al5e_setup_codec_cdev(codec, current_minor);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to setup cdev");
+		al5_codec_tear_down(codec);
+		return err;
+	}
+	codec->minor = current_minor;
+	++current_minor;
+
+	return 0;
+}
+
+static int al5e_remove(struct platform_device *pdev)
+{
+	struct al5_codec_desc *codec = platform_get_drvdata(pdev);
+	dev_t dev = MKDEV(al5e_codec_major, codec->minor);
+
+	al5_codec_tear_down(codec);
+	device_destroy(module_class, dev);
+	al5_clean_up_codec_cdev(codec);
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+	xil_clk_clean_up(pdev, codec);
+#endif
+
+	return 0;
+}
+
+static const struct of_device_id al5e_of_match[] = {
+	{ .compatible = "al,al5e" },
+	{ /* sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, al5e_of_match);
+
+static struct platform_driver al5e_platform_driver = {
+	.probe			= al5e_probe,
+	.remove			= al5e_remove,
+	.driver			=       {
+		.name		= "al5e",
+		.of_match_table = of_match_ptr(al5e_of_match),
+	},
+};
+
+static int setup_chrdev_region(void)
+{
+	return al5_setup_chrdev_region(&al5e_codec_major, 0,
+				       al5e_codec_nr_devs, "al5e");
+}
+
+static int create_module_class(void)
+{
+	module_class = class_create(THIS_MODULE, "allegro_encode_class");
+	if (IS_ERR(module_class))
+		return PTR_ERR(module_class);
+
+	return 0;
+}
+
+static void destroy_module_class(void)
+{
+	class_destroy(module_class);
+}
+
+static int __init al5e_init(void)
+{
+	int err;
+
+	err = setup_chrdev_region();
+	if (err)
+		return err;
+
+	err = create_module_class();
+	if (err)
+		return err;
+
+	return platform_driver_register(&al5e_platform_driver);
+}
+
+static void __exit al5e_exit(void)
+{
+	dev_t devno = MKDEV(al5e_codec_major, 0);
+
+	platform_driver_unregister(&al5e_platform_driver);
+	destroy_module_class();
+	unregister_chrdev_region(devno, al5e_codec_nr_devs);
+}
+
+module_init(al5e_init);
+module_exit(al5e_exit);
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Kevin Grandemange");
+MODULE_AUTHOR("Sebastien Alaiwan");
+MODULE_AUTHOR("Antoine Gruzelle");
+MODULE_DESCRIPTION("Allegro Codec Driver");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/al_enc_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/al_enc_ioctl.h
@@ -0,0 +1,75 @@
+/*
+ * al_enc_ioctl.h structure used to communicate with the userspace
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_ENC_IOCTL_H_
+#define _AL_ENC_IOCTL_H_
+#include "al_ioctl.h"
+#include <linux/types.h>
+
+#define AL_MCU_CONFIG_CHANNEL  _IOWR('q', 2, struct al5_config_channel)
+#define AL_MCU_DESTROY_CHANNEL  _IO('q', 4)
+#define AL_MCU_ENCODE_ONE_FRM _IOWR('q', 5, struct al5_encode_msg)
+#define AL_MCU_WAIT_FOR_STATUS _IOWR('q', 6, struct al5_params)
+
+#define AL_MCU_PUT_STREAM_BUFFER _IOWR('q', 22, struct al5_buffer)
+
+#define AL_MCU_GET_REC_PICTURE _IOWR('q', 23, struct al5_reconstructed_info)
+#define AL_MCU_RELEASE_REC_PICTURE _IOWR('q', 24, __u32)
+
+
+struct al5_reconstructed_info {
+	__u32 fd;
+	__u32 pic_struct;
+	__u32 poc;
+	__u32 width;
+	__u32 height;
+};
+
+struct al5_params {
+	__u32 size;
+	__u32 opaque_params[128];
+};
+
+struct al5_channel_status {
+	__u32 error_code;
+};
+
+struct al5_config_channel {
+	struct al5_params param;
+	struct al5_channel_status status;
+	__u32 rc_plugin_fd;
+};
+
+struct al5_encode_msg {
+	struct al5_params params;
+	struct al5_params addresses;
+};
+
+struct al5_stream_buffer {
+	__u64 stream_buffer_ptr;
+	__u32 handle;
+	__u32 offset;
+	__u32 size;
+};
+
+struct al5_buffer {
+	struct al5_stream_buffer stream_buffer;
+	__u32 external_mv_handle;
+};
+
+#endif  /* _AL_ENC_IOCTL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/enc_feedbacks.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/enc_feedbacks.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef __AL_FEEDBACKS__
+#define __AL_FEEDBACKS__
+
+#include <linux/types.h>
+
+struct al5_channel_buffers {
+	__u32 int_buffers_count;
+	__u32 int_buffers_size;
+	__u32 rec_buffers_count;
+	__u32 rec_buffers_size;
+	__u32 reserved;
+};
+
+struct al5e_feedback_channel {
+	u32 chan_uid;
+	u32 user_uid;
+	struct al5_channel_buffers buffers_needed;
+	u32 error_code;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/enc_mails_factory.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/enc_mails_factory.c
@@ -0,0 +1,65 @@
+/*
+ * enc_mails_factory.c high level message creation for the mcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/types.h>
+#include <linux/string.h>
+
+#include "enc_mails_factory.h"
+
+void al5e_mail_get_status(struct al5_params *status,
+			  struct al5_mail *mail)
+{
+	status->size = al5_mail_get_size(mail) - 4;
+	memcpy(status->opaque_params, al5_mail_get_body(mail) + 4,
+	       status->size);
+}
+
+struct al5_mail *al5e_create_encode_one_frame_msg(u32 chan_uid,
+						  struct al5_encode_msg *msg)
+{
+	int mail_size = 8 + msg->params.size + msg->addresses.size;
+	struct al5_mail *mail = al5_mail_create(AL_MCU_MSG_ENCODE_ONE_FRM,
+						mail_size);
+
+	const int padding = 0;
+
+	al5_mail_write_word(mail, chan_uid);
+	al5_mail_write_word(mail, padding);
+	al5_mail_write(mail, msg->params.opaque_params, msg->params.size);
+	al5_mail_write(mail, msg->addresses.opaque_params, msg->addresses.size);
+
+	return mail;
+}
+
+struct al5_mail *al5e_create_channel_param_msg(u32 user_uid,
+					       struct al5_params *msg,
+					       u32 mcu_rc_plugin_addr,
+					       u32 mcu_rc_plugin_size)
+{
+	/* One word for the user uid and two words for the rc plugin */
+	struct al5_mail *mail = al5_mail_create(AL_MCU_MSG_CREATE_CHANNEL, msg->size + 3 * sizeof(u32));
+	if(!mail)
+		return NULL;
+
+	al5_mail_write_word(mail, user_uid);
+	al5_mail_write(mail, msg->opaque_params, msg->size);
+	al5_mail_write_word(mail, mcu_rc_plugin_addr);
+	al5_mail_write_word(mail, mcu_rc_plugin_size);
+
+	return mail;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/enc_mails_factory.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/enc_mails_factory.h
@@ -0,0 +1,35 @@
+/*
+ * enc_mails_factory.h high level message creation for the mcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _MCU_ENC_H_
+#define _MCU_ENC_H_
+
+#include "al_mail.h"
+#include "al_enc_ioctl.h"
+#include "al_codec_mails.h"
+
+void al5e_mail_get_status(struct al5_params *status,
+			  struct al5_mail *mail);
+struct al5_mail *al5e_create_encode_one_frame_msg(u32 chan_uid,
+						  struct al5_encode_msg *msg);
+struct al5_mail *al5e_create_channel_param_msg(u32 user_uid,
+					       struct al5_params *msg,
+					       u32 mcu_rc_plugin_addr,
+					       u32 mcu_rc_plugin_size);
+
+#endif /* _MCU_ENC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/enc_user.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/enc_user.c
@@ -0,0 +1,430 @@
+/*
+ * enc_user.c high level communication with the vcu and the firmware
+ * channel creation, frame encoding
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/types.h>
+#include <linux/string.h>
+#include <linux/mutex.h>
+
+#include "enc_user.h"
+#include "enc_mails_factory.h"
+#include "enc_feedbacks.h"
+#include "al_dmabuf.h"
+#include "al_buffers_pool.h"
+
+static void update_chan_param(struct al5_channel_status *status,
+			      struct al5e_feedback_channel *message)
+{
+	status->error_code = message->error_code;
+}
+
+static int chan_is_valid(u32 chan_uid)
+{
+	return chan_uid == BAD_CHAN ? -EINVAL : 0;
+}
+
+static struct al5_mail *create_mail_from_bufpool(u32 msg_uid, u32 chan_uid,
+						 struct al5_buffers_pool bufpool)
+{
+	struct al5_mail *mail;
+	int i;
+	u32 size_per_buffer = 3 * sizeof(u32);
+	u32 content_size = bufpool.count * size_per_buffer;
+
+	mail = al5_mail_create(msg_uid, 4 + content_size);
+	al5_mail_write_word(mail, chan_uid);
+	for (i = 0; i < bufpool.count; i++) {
+		struct al5_dma_buffer *buffer = bufpool.buffers[i];
+		u32 mcu_vaddr = al5_mcu_get_virtual_address(
+			(u32)(uintptr_t)buffer->dma_handle);
+		/* ip and mcu only support a 2G dma zone */
+		al5_mail_write_word(mail, (u32)(uintptr_t)buffer->dma_handle);
+		al5_mail_write_word(mail, mcu_vaddr);
+		al5_mail_write_word(mail, buffer->size);
+	}
+
+	return mail;
+}
+
+static int allocate_channel_buffers(struct al5_user *user,
+				    struct al5_channel_buffers buffers)
+{
+	int err;
+	unsigned long pagesize = (1 << PAGE_SHIFT);
+
+	buffers.rec_buffers_size += pagesize -
+				    (buffers.rec_buffers_size % pagesize);
+	err = al5_bufpool_allocate(&user->int_buffers, user->device,
+				   buffers.int_buffers_count,
+				   buffers.int_buffers_size);
+	if (err)
+		return err;
+	err = al5_bufpool_allocate(&user->rec_buffers, user->device,
+				   buffers.rec_buffers_count,
+				   buffers.rec_buffers_size);
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static int send_intermediate_buffers(struct al5_user *user)
+{
+	struct al5_mail *mail;
+
+	mail = create_mail_from_bufpool(AL_MCU_MSG_PUSH_BUFFER_INTERMEDIATE,
+					user->chan_uid, user->int_buffers);
+	return al5_check_and_send(user, mail);
+}
+
+static int send_reference_buffers(struct al5_user *user)
+{
+	struct al5_mail *mail;
+
+	mail = create_mail_from_bufpool(AL_MCU_MSG_PUSH_BUFFER_REFERENCE,
+					user->chan_uid, user->rec_buffers);
+	return al5_check_and_send(user, mail);
+}
+
+static int try_to_create_channel(struct al5_user *user,
+				 struct al5_config_channel *msg,
+				 struct al5e_feedback_channel *fb_message)
+{
+	struct al5_params *param = &msg->param;
+	struct al5_channel_status *status = &msg->status;
+	struct al5_mail *feedback;
+	int err;
+
+	struct al5_buffer_info rc_plugin_info;
+	u32 mcu_rc_plugin_addr = 0;
+	u32 mcu_rc_plugin_size = 0;
+
+	if (msg->rc_plugin_fd != -1) {
+		err = al5_get_dmabuf_info(user->device, msg->rc_plugin_fd,
+					    &rc_plugin_info);
+		if (err)
+			return err;
+		mcu_rc_plugin_addr = al5_mcu_get_virtual_address(rc_plugin_info.bus_address);
+		mcu_rc_plugin_size = rc_plugin_info.size;
+	}
+
+	err =  al5_check_and_send(user, al5e_create_channel_param_msg(user->uid,
+									  param,
+									  mcu_rc_plugin_addr,
+									  mcu_rc_plugin_size));
+
+	if (err)
+		return err;
+
+	err = al5_queue_pop_timeout(&feedback,
+				    &user->queues[AL5_USER_MAIL_CREATE]);
+	if (err)
+		return err;
+
+	*fb_message =
+		*(struct al5e_feedback_channel *)al5_mail_get_body(feedback);
+	al5_free_mail(feedback);
+	update_chan_param(status, fb_message);
+
+	err = chan_is_valid(fb_message->chan_uid);
+	if (err) {
+		dev_err(user->device,
+			"VCU: unavailable resources or wrong configuration");
+		return err;
+	}
+
+	return 0;
+}
+
+int al5e_user_create_channel(struct al5_user *user, struct al5_config_channel *msg)
+{
+	struct al5e_feedback_channel fb_message = { 0 };
+	int err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+
+	if (err == -EINTR)
+		return err;
+
+	if (al5_chan_is_created(user)) {
+		err = -EPERM;
+		dev_err(user->device, "Channel already created (%d, %d)", user->uid,
+			user->chan_uid);
+		goto fail;
+	}
+
+	if (user->checkpoint == CHECKPOINT_DESTROYED)
+		user->checkpoint = NO_CHECKPOINT;
+
+	if (user->checkpoint == NO_CHECKPOINT) {
+		err = try_to_create_channel(user, msg, &fb_message);
+		if (err) {
+			dev_warn_ratelimited(user->device,
+					     "Failed on create channel (%d)", user->uid);
+			goto fail;
+		}
+		user->checkpoint = CHECKPOINT_ALLOCATE_BUFFERS;
+	}
+
+	if (user->checkpoint == CHECKPOINT_ALLOCATE_BUFFERS) {
+		err = allocate_channel_buffers(user, fb_message.buffers_needed);
+		if (err) {
+			dev_warn_ratelimited(user->device,
+					     "Failed internal buffers allocation, channel (%d, %d) isn't fully created yet", user->uid, user->chan_uid);
+			goto fail_allocate;
+		}
+		user->checkpoint = CHECKPOINT_SEND_INTERMEDIATE_BUFFERS;
+	}
+
+	if (user->checkpoint == CHECKPOINT_SEND_INTERMEDIATE_BUFFERS) {
+		err = send_intermediate_buffers(user);
+		if (err) {
+			dev_warn_ratelimited(user->device,
+					     "Failed to send intermediate buffers, channel (%d, %d) isn't fully created yet", user->uid, user->chan_uid);
+			goto fail;
+		}
+		user->checkpoint = CHECKPOINT_SEND_REFERENCE_BUFFERS;
+	}
+
+	if (user->checkpoint == CHECKPOINT_SEND_REFERENCE_BUFFERS) {
+		err = send_reference_buffers(user);
+		if (err) {
+			dev_warn_ratelimited(user->device,
+					     "Failed to send reference buffers, channel (%d, %d) isn't fully created yet", user->uid, user->chan_uid);
+			goto fail;
+		}
+		user->checkpoint = CHECKPOINT_CREATED;
+	}
+
+	dev_dbg(user->device, "Created channel (%d, %d)", user->uid, user->chan_uid);
+
+	goto unlock;
+
+fail_allocate:
+	user->checkpoint = NO_CHECKPOINT;
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	al5_user_destroy_channel(user, 0);
+	return err;
+fail:
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5e_user_create_channel);
+
+int al5e_user_encode_one_frame(struct al5_user *user,
+			       struct al5_encode_msg *msg)
+{
+	int err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+
+	if (err == -EINTR)
+		return err;
+
+	if (!al5_chan_is_created(user)) {
+		dev_err(user->device, "Cannot encode frame until channel is configured (%d, %d)", user->uid, user->chan_uid);
+		err = -EPERM;
+		goto unlock;
+	}
+
+	err = al5_check_and_send(user,
+				 al5e_create_encode_one_frame_msg(user->chan_uid,
+								  msg));
+
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5e_user_encode_one_frame);
+
+int al5e_user_wait_for_status(struct al5_user *user,
+			      struct al5_params *msg)
+{
+	struct al5_mail *feedback;
+	int err = 0;
+
+	if (!mutex_trylock(&user->locks[AL5_USER_STATUS]))
+		return -EINTR;
+
+	if (!al5_chan_is_created(user)) {
+		dev_dbg(user->device,
+			"Cannot get a frame status if the channel isn't configured (%d, %d)", user->uid,
+			user->chan_uid);
+		err = -EPERM;
+		goto unlock;
+	}
+
+	if (user->non_block) {
+		feedback = al5_queue_pop_no_wait(&user->queues[AL5_USER_MAIL_STATUS]);
+		if (feedback)
+			al5e_mail_get_status(msg, feedback);
+		else
+			err = -EWOULDBLOCK;
+	}else {
+		feedback = al5_queue_pop(&user->queues[AL5_USER_MAIL_STATUS]);
+		if (feedback)
+			al5e_mail_get_status(msg, feedback);
+		else
+			err = -EINTR;
+	}
+
+	al5_free_mail(feedback);
+
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_STATUS]);
+	return err;
+}
+
+int al5e_user_put_stream_buffer(struct al5_user *user,
+				struct al5_buffer *buffer)
+{
+	struct al5_buffer_info stream_buffer_info;
+	struct al5_buffer_info external_mv_buffer_info;
+	struct al5_mail *mail;
+	u32 stream_mcu_vaddr;
+	u32 external_mv_mcu_vaddr = 0;
+
+	int err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+
+	if (!al5_chan_is_created(user)) {
+		dev_err(user->device, "Cannot put a stream buffer if the channel isn't configured (%d, %d)", user->uid, user->chan_uid);
+		err = -EPERM;
+		goto unlock;
+	}
+
+	err = al5_get_dmabuf_info(user->device, buffer->stream_buffer.handle,
+				  &stream_buffer_info);
+	if (err)
+		goto unlock;
+
+	if (buffer->stream_buffer.size > stream_buffer_info.size) {
+		err = -EFAULT;
+		goto unlock;
+	}
+
+	if (buffer->external_mv_handle != 0) {
+		err = al5_get_dmabuf_info(user->device, buffer->external_mv_handle,
+					  &external_mv_buffer_info);
+		if (err)
+			goto unlock;
+		external_mv_mcu_vaddr = al5_mcu_get_virtual_address(
+			external_mv_buffer_info.bus_address);
+	}
+
+	mail = al5_mail_create(AL_MCU_MSG_PUT_STREAM_BUFFER, 32);
+	al5_mail_write_word(mail, user->chan_uid);
+	al5_mail_write_word(mail, stream_buffer_info.bus_address);
+	stream_mcu_vaddr = al5_mcu_get_virtual_address(stream_buffer_info.bus_address);
+	al5_mail_write_word(mail, stream_mcu_vaddr);
+	al5_mail_write_word(mail, buffer->stream_buffer.size);
+	al5_mail_write_word(mail, buffer->stream_buffer.offset);
+	al5_mail_write(mail, &buffer->stream_buffer.stream_buffer_ptr, 8);
+	al5_mail_write_word(mail, external_mv_mcu_vaddr);
+
+	err = al5_check_and_send(user, mail);
+
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+
+static int get_user_rec_buffer(struct al5_user *user, int id)
+{
+	if (id > user->rec_buffers.count || id < 0)
+		return -1;
+	return al5_bufpool_reserve_fd(&user->rec_buffers, id);
+}
+
+int al5e_user_get_rec(struct al5_user *user, struct al5_reconstructed_info *msg)
+{
+	int err = 0;
+	struct al5_mail *feedback;
+	struct al5_mail *mail;
+
+	if (!mutex_trylock(&user->locks[AL5_USER_CHANNEL]))
+		return -EINTR;
+
+	if (!al5_chan_is_created(user)) {
+		dev_err(user->device, "Cannot get a reconstructed buffer if the channel isn't configured (%d, %d)", user->uid, user->chan_uid);
+		err = -EPERM;
+		goto unlock;
+	}
+
+	mail = al5_create_empty_mail(user->chan_uid,
+				     AL_MCU_MSG_GET_RECONSTRUCTED_PICTURE);
+
+	err = al5_check_and_send(user, mail);
+	if (err)
+		goto unlock;
+
+	feedback = al5_queue_pop(&user->queues[AL5_USER_MAIL_REC]);
+	if (!feedback) {
+		err = -EINTR;
+		goto unlock;
+	}
+
+	msg->fd = get_user_rec_buffer(user, al5_mail_get_word(feedback, 1));
+	if (msg->fd == -1) {
+		err = -EINVAL;
+		goto no_rec_buf;
+	}
+
+	msg->pic_struct = al5_mail_get_word(feedback, 2);
+	msg->poc = al5_mail_get_word(feedback, 3);
+	if (al5_mail_get_size(feedback) > 3 * sizeof(u32)) {
+		msg->width = al5_mail_get_word(feedback, 4);
+		msg->height = al5_mail_get_word(feedback, 5);
+	} else
+		dev_err(user->device,
+			"Your firmware version is too old, you need to update");
+
+no_rec_buf:
+	al5_free_mail(feedback);
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+
+int al5e_user_release_rec(struct al5_user *user, u32 fd)
+{
+	u32 uid;
+	int id;
+	struct al5_mail *mail;
+	int err = 0;
+
+	if (!mutex_trylock(&user->locks[AL5_USER_CHANNEL]))
+		return -EINTR;
+
+	if (!al5_chan_is_created(user)) {
+		dev_err(user->device, "Cannot release a reconstructed buffer if the channel isn't configured (%d, %d)", user->uid, user->chan_uid);
+		err = -EPERM;
+		goto unlock;
+	}
+
+	id = al5_bufpool_get_id(&user->rec_buffers, fd);
+	if (id < 0) {
+		err = -EINVAL;
+		goto unlock;
+	}
+	uid = id;
+	mail = al5_create_classic_mail(user->chan_uid,
+				       AL_MCU_MSG_RELEASE_RECONSTRUCTED_PICTURE,
+				       &uid, sizeof(uid));
+
+	err = al5_check_and_send(user, mail);
+unlock:
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+	return err;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/al5e/enc_user.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/al5e/enc_user.h
@@ -0,0 +1,33 @@
+/*
+ * enc_user.h high level communication with the vcu and the firmware
+ * channel creation, frame encoding
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "al_user.h"
+#include "al_enc_ioctl.h"
+
+int al5e_user_create_channel(struct al5_user *user,
+			     struct al5_config_channel *msg);
+int al5e_user_encode_one_frame(struct al5_user *user,
+			       struct al5_encode_msg *msg);
+int al5e_user_wait_for_status(struct al5_user *user,
+			      struct al5_params *msg);
+int al5e_user_put_stream_buffer(struct al5_user *user,
+				struct al5_buffer *buffer);
+
+int al5e_user_release_rec(struct al5_user *user, u32 fd);
+int al5e_user_get_rec(struct al5_user *user,
+		      struct al5_reconstructed_info *msg);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/Makefile
@@ -0,0 +1,28 @@
+ccflags-y += -I$(srctree)/$(src)/../include
+
+obj-m += allegro.o
+
+allegro-objs := \
+	al_alloc.o \
+	al_alloc_ioctl.o \
+	al_buffers_pool.o \
+	al_char.o \
+	al_codec.o \
+	al_dmabuf.o \
+	al_user.o \
+	al_vcu.o \
+	al_mail.o \
+	al_codec_mails.o \
+	al_mailbox.o \
+	al_list.o \
+	al_queue.o \
+	mcu_interface.o \
+	mcu_utils.o \
+	al_group.o \
+
+ifeq ($(CONFIG_ALLEGRO_ONLY),1)
+  allegro-objs += al_l2_prefetch.o
+else
+  allegro-objs += xil_l2_prefetch.o
+  allegro-objs += xil_clk.o
+endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_alloc.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_alloc.c
@@ -0,0 +1,97 @@
+/*
+ * al_alloc.c dma buffers allocation and dmabuf support
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/dma-buf.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include "al_alloc.h"
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Kevin Grandemange");
+MODULE_AUTHOR("Sebastien Alaiwan");
+MODULE_AUTHOR("Antoine Gruzelle");
+MODULE_DESCRIPTION("Allegro Common");
+
+struct al5_dma_buffer *al5_alloc_dma_(struct device *dev, size_t size)
+{
+	struct al5_dma_buffer *buf =
+		kmalloc(sizeof(struct al5_dma_buffer),
+			GFP_KERNEL);
+
+	if (!buf)
+		return NULL;
+
+	buf->offset = 0;
+	buf->size = size;
+	buf->cpu_handle = dma_alloc_coherent(dev, buf->size,
+					     &buf->dma_handle,
+					     GFP_KERNEL | GFP_DMA | __GFP_NOWARN);
+
+	if (!buf->cpu_handle) {
+		kfree(buf);
+		return NULL;
+	}
+
+	return buf;
+}
+
+struct al5_dma_buffer *al5_alloc_dma(struct device *dev, size_t size)
+{
+	struct al5_dma_buffer *buf = al5_alloc_dma_(dev, size);
+
+	if (!buf)
+		return NULL;
+
+	if ((buf->dma_handle & 0xffffffff) != 0)
+		return buf;
+
+	/* Deal with special case of a buffer with lsb == 0 (not accepted by the firmware)
+	   Retry the allocation with size + PAGE_SIZE and if we get lsb == 0 again, add a one page
+	   offset to the start of the buffer */
+	dma_free_coherent(dev, buf->size, buf->cpu_handle, buf->dma_handle);
+	buf = al5_alloc_dma_(dev, size + PAGE_SIZE);
+	if (!buf)
+		return NULL;
+
+	if ((buf->dma_handle & 0xffffffff) == 0) {
+		buf->offset = PAGE_SIZE;
+		buf->size -= PAGE_SIZE;
+		buf->cpu_handle += PAGE_SIZE;
+		buf->dma_handle += PAGE_SIZE;
+	}
+
+	return buf;
+}
+EXPORT_SYMBOL_GPL(al5_alloc_dma);
+
+void al5_free_dma(struct device *dev, struct al5_dma_buffer *buf)
+{
+	if (!buf)
+		return;
+
+	buf->cpu_handle -= buf->offset;
+	buf->dma_handle -= buf->offset;
+	buf->size += buf->offset;
+	dma_free_coherent(dev, buf->size, buf->cpu_handle,
+			  buf->dma_handle);
+	kfree(buf);
+}
+EXPORT_SYMBOL_GPL(al5_free_dma);
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_alloc_ioctl.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_alloc_ioctl.c
@@ -0,0 +1,63 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include "al_alloc_ioctl.h"
+#include "al_dmabuf.h"
+
+#include <linux/uaccess.h>
+
+int al5_ioctl_get_dma_fd(struct device *dev, unsigned long arg)
+{
+	struct al5_dma_info info;
+	int err;
+
+	if (copy_from_user(&info, (struct al5_dma_info *)arg, sizeof(info)))
+		return -EFAULT;
+
+	err = al5_allocate_dmabuf(dev, info.size, &info.fd);
+	if (err)
+		return err;
+
+	err = al5_dmabuf_get_address(dev, info.fd, &info.phy_addr);
+	if (err)
+		return err;
+
+	if (copy_to_user((void *)arg, &info, sizeof(info)))
+		return -EFAULT;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_ioctl_get_dma_fd);
+
+int al5_ioctl_get_dmabuf_dma_addr(struct device *dev, unsigned long arg)
+{
+	struct al5_dma_info info;
+	int err;
+
+	if (copy_from_user(&info, (struct al5_dma_info *)arg, sizeof(info)))
+		return -EFAULT;
+
+	err = al5_dmabuf_get_address(dev, info.fd, &info.phy_addr);
+	if (err)
+		return err;
+
+	if (copy_to_user((void *)arg, &info, sizeof(info)))
+		return -EFAULT;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_ioctl_get_dmabuf_dma_addr);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_buffers_pool.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_buffers_pool.c
@@ -0,0 +1,113 @@
+/*
+ * al_buffers_pool.c high level function to write messages in the mailbox
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/slab.h>
+
+#include "al_dmabuf.h"
+#include <linux/dma-buf.h>
+#include "al_buffers_pool.h"
+
+void al5_bufpool_init(struct al5_buffers_pool *bufpool)
+{
+	memset(bufpool, 0, sizeof(*bufpool));
+}
+
+int al5_bufpool_allocate(struct al5_buffers_pool *bufpool,
+			 struct device *device, int count, int size)
+{
+	int i;
+
+	bufpool->count = 0;
+	bufpool->buffers = kcalloc(count, sizeof(struct al5_dma_buffer *),
+				   GFP_KERNEL);
+	if (!bufpool->buffers)
+		goto fail_buffers;
+
+	bufpool->handles = kcalloc(count, sizeof(void *), GFP_KERNEL);
+	if (!bufpool->handles)
+		goto fail_handles;
+
+	for (i = 0; i < count; i++) {
+		bufpool->buffers[i] = al5_alloc_dma(device, size);
+		if (bufpool->buffers[i] == NULL)
+			goto fail_dma_allocation;
+		bufpool->handles[i] = al5_dmabuf_wrap(device, size, bufpool->buffers[i]);
+		if (IS_ERR(bufpool->handles[i])) {
+			al5_free_dma(device, bufpool->buffers[i]);
+			goto fail_dma_allocation;
+		}
+		++bufpool->count;
+	}
+
+	return 0;
+
+fail_dma_allocation:
+	al5_bufpool_free(bufpool, device);
+	return -ENOMEM;
+
+fail_handles:
+	kfree(bufpool->buffers);
+fail_buffers:
+	return -ENOMEM;
+}
+EXPORT_SYMBOL_GPL(al5_bufpool_allocate);
+
+void al5_bufpool_free(struct al5_buffers_pool *bufpool, struct device *device)
+{
+	int i;
+
+	for (i = 0; i < bufpool->count; ++i)
+		dma_buf_put(bufpool->handles[i]);
+
+	kfree(bufpool->buffers);
+	kfree(bufpool->handles);
+	bufpool->buffers = NULL;
+	bufpool->handles = NULL;
+	memset(bufpool, 0, sizeof(*bufpool));
+}
+EXPORT_SYMBOL_GPL(al5_bufpool_free);
+
+int al5_bufpool_get_id(struct al5_buffers_pool *bufpool, int fd)
+{
+	u32 i = 0;
+	struct dma_buf *handle = dma_buf_get(fd);
+
+	if (IS_ERR(handle))
+		return -1;
+
+	for (i = 0; i < bufpool->count; ++i) {
+		if (handle == bufpool->handles[i]) {
+			dma_buf_put(handle);
+			return i;
+		}
+	}
+	dma_buf_put(handle);
+	return -1;
+}
+EXPORT_SYMBOL_GPL(al5_bufpool_get_id);
+
+int al5_bufpool_reserve_fd(struct al5_buffers_pool *bufpool, int id)
+{
+	struct dma_buf *dbuf = bufpool->handles[id];
+	int fd = dma_buf_fd(dbuf, O_RDWR);
+
+	dma_buf_get(fd);
+	return fd;
+}
+EXPORT_SYMBOL_GPL(al5_bufpool_reserve_fd);
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_char.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_char.c
@@ -0,0 +1,63 @@
+/*
+ * al_char.c char device setup helpers
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "al_codec.h"
+
+int al5_setup_chrdev_region(int *major, int base_minor, int nb_devs, char *desc)
+{
+	dev_t dev = 0;
+	int err;
+
+	if (*major == 0) {
+		err = alloc_chrdev_region(&dev, base_minor, nb_devs, desc);
+		*major = MAJOR(dev);
+
+		if (err) {
+			pr_alert("Allegro codec: can't get major %d\n",
+				 *major);
+			return err;
+		}
+	}
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_setup_chrdev_region);
+
+int al5_setup_codec_cdev(struct al5_codec_desc *codec,
+			 const struct file_operations *fops,
+			 struct module *owner, int major, int minor)
+{
+	int err, devno = MKDEV(major, minor);
+
+	cdev_init(&codec->cdev, fops);
+	codec->cdev.owner = owner;
+	err = cdev_add(&codec->cdev, devno, 1);
+	if (err) {
+		al5_err("Error %d adding allegro device number %d", err, minor);
+		return err;
+	}
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_setup_codec_cdev);
+
+void al5_clean_up_codec_cdev(struct al5_codec_desc *codec)
+{
+	cdev_del(&codec->cdev);
+}
+EXPORT_SYMBOL_GPL(al5_clean_up_codec_cdev);
+
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_codec.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_codec.c
@@ -0,0 +1,578 @@
+/*
+ * al_codec.c per device operation. functions to change the state of the vcu
+ * and functions to handle channels created by the user.
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/delay.h>
+#include <linux/of_address.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/of.h>
+#include <linux/version.h>
+
+#include "al_mail.h"
+#include "al_codec_mails.h"
+#include "mcu_utils.h"
+#include "al_codec.h"
+#include "al_alloc.h"
+#include "mcu_interface.h"
+
+#ifdef CONFIG_MEMORY_HOTPLUG
+#define HOTPLUG_ALIGN 0x40000000
+#endif
+static void set_icache_offset(struct al5_codec_desc *codec)
+{
+	dma_addr_t dma_handle = codec->icache->dma_handle - MCU_CACHE_OFFSET;
+	unsigned long msb = 0;
+	u32 icache_offset_lsb;
+	u32 icache_offset_msb;
+
+	if (codec->icache->dma_handle < MCU_CACHE_OFFSET)
+		msb = 0xFFFFFFFF;
+
+	icache_offset_lsb = (u32)dma_handle;
+	icache_offset_msb = (sizeof(dma_handle) == 4) ? msb : dma_handle >> 32;
+	al5_writel(icache_offset_lsb, AL5_ICACHE_ADDR_OFFSET_LSB);
+	al5_writel(icache_offset_msb, AL5_ICACHE_ADDR_OFFSET_MSB);
+}
+
+static void set_dcache_offset(struct al5_codec_desc *codec)
+{
+	dma_addr_t mem_seg = codec->icache->dma_handle & 0xffffffff00000000;
+	dma_addr_t dma_handle = mem_seg - MCU_CACHE_OFFSET;
+	unsigned long msb = 0;
+	u32 dcache_offset_lsb;
+	u32 dcache_offset_msb;
+
+	if (mem_seg < MCU_CACHE_OFFSET)
+		msb = 0xFFFFFFFF;
+
+	dcache_offset_lsb = (u32)dma_handle;
+	dcache_offset_msb = (sizeof(dma_handle) == 4) ? msb : dma_handle >> 32;
+
+	al5_writel(dcache_offset_msb, AL5_DCACHE_ADDR_OFFSET_MSB);
+	al5_writel(dcache_offset_lsb, AL5_DCACHE_ADDR_OFFSET_LSB);
+}
+
+static int copy_firmware(struct al5_codec_desc *codec,
+			 const struct firmware *fw,
+			 const struct firmware *bl_fw)
+{
+	setup_info("firmware size is %zx", fw->size);
+	setup_info("bootloader firmware size is %zx", bl_fw->size);
+
+	if (fw->size > AL5_ICACHE_SIZE) {
+		al5_err("firmware is too big");
+		return -EINVAL;
+	}
+
+	if (bl_fw->size > MCU_SRAM_SIZE) {
+		al5_err("bootloader firmware is too big");
+		return -EINVAL;
+	}
+
+	memcpy(codec->icache->cpu_handle, fw->data, fw->size);
+	memcpy_toio_32(codec->regs, bl_fw->data, bl_fw->size);
+
+	return 0;
+}
+
+static void stop_mcu(struct al5_codec_desc *codec)
+{
+	int time = 0;
+
+	al5_writel(0, AL5_MCU_WAKEUP);
+	al5_writel(MCU_SLEEP_INSTRUCTION, AL5_MCU_INTERRUPT_HANDLER);
+	al5_signal_mcu(codec->users_group.mcu);
+
+	while ((al5_readl(AL5_MCU_STA) & 1) != 1 && time < 100) {
+		msleep(20);
+		time += 20;
+	}
+}
+
+static void reset_mcu(struct al5_codec_desc *codec)
+{
+	/* Mode 1 Reset MCU (sleep) */
+	al5_writel(1, AL5_MCU_RESET_MODE);
+	al5_writel(0, AL5_MCU_WAKEUP);
+
+	/* Reset MCU */
+	al5_writel(1, AL5_MCU_RESET);
+
+}
+
+static void start_mcu(struct al5_codec_desc *codec)
+{
+	al5_writel(1, AL5_MCU_WAKEUP);
+}
+
+static void set_mcu_interrupt_mask(struct al5_codec_desc *codec)
+{
+	al5_writel(1, AL5_MCU_INTERRUPT_MASK);
+}
+
+static int request_all_firmwares(struct al5_codec_desc *codec,
+				 const struct firmware **fw,
+				 const struct firmware **bl_fw,
+				 char *fw_file,
+				 char *bl_fw_file)
+{
+	int err;
+
+	err = request_firmware(fw, fw_file, codec->device);
+	if (err) {
+		al5_err("firmware file '%s' not found", fw_file);
+		goto out_failed;
+	}
+
+	err = request_firmware(bl_fw, bl_fw_file, codec->device);
+	if (err) {
+		al5_err("bootloader firmware file '%s' not found",
+			bl_fw_file);
+		goto out_failed_firmware;
+	}
+
+	return 0;
+
+out_failed_firmware:
+	release_firmware(*fw);
+out_failed:
+	return err;
+
+}
+
+static int setup_and_start_mcu(struct al5_codec_desc *codec,
+			       const struct firmware *fw,
+			       const struct firmware *bl_fw)
+{
+	int ret;
+
+	stop_mcu(codec);
+	reset_mcu(codec);
+
+	ret = copy_firmware(codec, fw, bl_fw);
+	if (ret)
+		return ret;
+
+	set_icache_offset(codec);
+	set_dcache_offset(codec);
+	set_mcu_interrupt_mask(codec);
+
+	start_mcu(codec);
+
+	return 0;
+}
+
+static int alloc_mcu_caches(struct al5_codec_desc *codec)
+{
+	/* alloc the icache and the dcache */
+	codec->icache = al5_alloc_dma(codec->device, AL5_ICACHE_SIZE);
+	if (!codec->icache)
+		return -ENOMEM;
+
+	/* dcache map base addr */
+
+	codec->dcache_base_addr = 0;
+
+	al5_writel(codec->icache->dma_handle >> 32, AXI_ADDR_OFFSET_IP);
+	setup_info("icache phy is at %p", (void *)codec->icache->dma_handle);
+
+	return 0;
+}
+
+u32 get_l2_size_in_bits(void *);
+u32 get_l2_color_bitdepth(void *);
+u32 get_num_cores(void *);
+u32 get_core_frequency(void *);
+
+static void set_l2_info(struct device *dev, struct mcu_init_msg *init_msg)
+{
+	void *parent = dev_get_drvdata(dev->parent);
+
+	if (!IS_ERR(parent)) {
+		init_msg->l2_size_in_bits = get_l2_size_in_bits(parent);
+		init_msg->l2_color_bitdepth = get_l2_color_bitdepth(parent);
+		init_msg->num_cores = get_num_cores(parent);
+		init_msg->core_frequency = get_core_frequency(parent);
+	} else {
+		init_msg->l2_size_in_bits = -1;
+		init_msg->l2_color_bitdepth = -1;
+		init_msg->num_cores = -1;
+		init_msg->core_frequency = -1;
+	}
+}
+
+static int init_mcu(struct al5_codec_desc *codec, struct al5_user *root,
+		    bool plugin_enabled)
+{
+	int err = 0;
+	struct mcu_init_msg init_msg;
+	struct al5_mail *feedback;
+
+	u32 mcu_memory_pool;
+	struct device_node *np = codec->device->of_node;
+
+	err = mutex_lock_killable(&root->locks[AL5_USER_INIT]);
+	if (err == -EINTR)
+		return err;
+
+	err = al5_queue_pop_timeout(&feedback,
+				    &root->queues[AL5_USER_MAIL_INIT]);
+	if (err) {
+		al5_err("Mcu didn't start (no ping after startup, is mcu enabled ?)");
+		goto unlock;
+	}
+	al5_free_mail(feedback);
+
+	mcu_memory_pool = MCU_SUBALLOCATOR_SIZE;
+	of_property_read_u32(np, "al,mcu_ext_mem_size", &mcu_memory_pool);
+
+	codec->suballoc_buf = al5_alloc_dma(codec->device, mcu_memory_pool);
+	if (!codec->suballoc_buf) {
+		err = -ENOMEM;
+		al5_err("Couldn't allocate mcu memory pool");
+		goto unlock;
+	}
+
+	init_msg.addr = codec->suballoc_buf->dma_handle + MCU_CACHE_OFFSET;
+	init_msg.size = codec->suballoc_buf->size;
+	set_l2_info(codec->device, &init_msg);
+	al5_info("l2 prefetch size:%d (bits), l2 color bitdepth:%d\n",
+		 init_msg.l2_size_in_bits, init_msg.l2_color_bitdepth);
+	init_msg.plugin_enabled = plugin_enabled;
+
+	err = al5_check_and_send(root, create_init_msg(root->uid, &init_msg));
+	if (err) {
+		al5_err("Couldn't send initial configuration to mcu");
+		goto fail_msg;
+	}
+
+	err = al5_queue_pop_timeout(&feedback, &root->queues[AL5_USER_MAIL_INIT]);
+	if (err) {
+		al5_err("Mcu didn't acknowledge its configuration");
+		goto fail_msg;
+	}
+	al5_free_mail(feedback);
+
+	mutex_unlock(&root->locks[AL5_USER_INIT]);
+	return 0;
+
+fail_msg:
+	al5_free_dma(codec->device, codec->suballoc_buf);
+	codec->suballoc_buf = NULL;
+unlock:
+	mutex_unlock(&root->locks[AL5_USER_INIT]);
+	return err;
+}
+
+unsigned int al5_codec_poll(struct file *filp, poll_table *wait)
+{
+	struct al5_filp_data *private_data = filp->private_data;
+	struct al5_user *user = private_data->user;
+	unsigned int mask = 0;
+	int err;
+
+	struct al5_queue *status = &user->queues[AL5_USER_MAIL_STATUS];
+	struct al5_queue *sc = &user->queues[AL5_USER_MAIL_SC];
+
+	poll_wait(filp, &status->queue, wait);
+	poll_wait(filp, &sc->queue, wait);
+
+	err = mutex_lock_killable(&user->locks[AL5_USER_CHANNEL]);
+	if (err == -EINTR)
+		return err;
+
+	if (user->checkpoint == CHECKPOINT_DESTROYED)
+		mask = POLLHUP;
+
+	mutex_unlock(&user->locks[AL5_USER_CHANNEL]);
+
+	spin_lock(&status->lock);
+	if (!al5_list_empty(status->list))
+		mask |= POLLIN;
+	spin_unlock(&status->lock);
+
+	spin_lock(&sc->lock);
+	if (!al5_list_empty(sc->list))
+		mask |= POLLIN;
+	spin_unlock(&sc->lock);
+
+	return mask;
+}
+EXPORT_SYMBOL_GPL(al5_codec_poll);
+
+int al5_codec_open(struct inode *inode, struct file *filp)
+{
+	struct al5_filp_data *private_data = kzalloc(sizeof(*private_data),
+						     GFP_KERNEL);
+	struct al5_user *user;
+	struct al5_codec_desc *codec;
+	int err;
+
+	user = kzalloc(sizeof(*user), GFP_KERNEL);
+	if (!user)
+		return -ENOMEM;
+	codec = container_of(inode->i_cdev, struct al5_codec_desc, cdev);
+	user->non_block = filp->f_flags & O_NONBLOCK;
+
+	err = al5_group_bind_user(&codec->users_group, user);
+	if (err) {
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 9, 0)
+		kfree_sensitive(user);
+#else
+		kzfree(user);
+#endif
+		return err;
+	}
+
+	private_data->codec = codec;
+	private_data->user = user;
+	filp->private_data = private_data;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_codec_open);
+
+void al5_user_destroy_channel_resources(struct al5_user *user);
+int al5_codec_release(struct inode *inode, struct file *filp)
+{
+	struct al5_filp_data *private_data = filp->private_data;
+	struct al5_user *user = private_data->user;
+	struct al5_codec_desc *codec = private_data->codec;
+
+	if (al5_chan_is_created(user)) {
+		const int quiet = 1;
+
+		/* best effort to destroy the channel if it wasn't already */
+		int ret = -1;
+		int tries = 0;
+		while (ret != 0 && tries < 10000) {
+			ret = al5_user_destroy_channel(user, quiet);
+			++tries;
+		}
+		if (ret != 0)
+			dev_err(codec->device,
+				"Failed to destroy channel on mcu. Something went wrong (%d)", ret);
+
+		/* best effort. If everything went wrong, still free the channel resources
+		 * to avoid leaks */
+		al5_user_destroy_channel_resources(user);
+	}
+	al5_user_remove_residual_messages(user);
+	al5_group_unbind_user(&codec->users_group, user);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 9, 0)
+	kfree_sensitive(user);
+	kfree_sensitive(filp->private_data);
+#else
+	kzfree(user);
+	kzfree(filp->private_data);
+#endif
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_codec_release);
+
+int al5_codec_set_firmware(struct al5_codec_desc *codec, char *fw_file,
+			   char *bl_fw_file)
+{
+	const struct firmware *fw = NULL;
+	const struct firmware *bl_fw = NULL;
+	struct al5_user root;
+	int err;
+	bool plugin_enabled;
+
+	err = request_all_firmwares(codec, &fw, &bl_fw, fw_file, bl_fw_file);
+	if (err)
+		return err;
+
+	/* We need to bind root before starting the mcu because we are waiting
+	 * for a sync msg
+	 */
+	err = al5_group_bind_user(&codec->users_group, &root);
+	if (err)
+		goto release_firmware;
+
+	err = setup_and_start_mcu(codec, fw, bl_fw);
+	if (err)
+		goto release_firmware;
+
+	/* after this, the mcu is set to send us an interrupt, we can't fail before
+	 * ack'ing it */
+	plugin_enabled = fw->size > AL5_RC_PLUGIN_CODE_START;
+
+	err = init_mcu(codec, &root, plugin_enabled);
+	if (err) {
+		stop_mcu(codec);
+		goto release_firmware;
+	}
+	al5_group_unbind_user(&codec->users_group, &root);
+
+release_firmware:
+	release_firmware(fw);
+	release_firmware(bl_fw);
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5_codec_set_firmware);
+
+int al5_codec_set_up(struct al5_codec_desc *codec, struct platform_device *pdev,
+		     size_t max_users_nb)
+{
+	int err, irq;
+	struct device_node *mem_node;
+	struct resource mem_res;
+	struct resource *res;
+	const char *device_name = dev_name(&pdev->dev);
+	struct mcu_mailbox_config config;
+	struct mcu_mailbox_interface *mcu;
+	unsigned long pgtable_padding;
+
+	codec->device = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "Can't get resource");
+		err = -ENODEV;
+		goto fail;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Failed to get IRQ");
+		err = irq;
+		goto fail;
+	}
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 6, 0)
+	codec->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+#else
+	codec->regs = devm_ioremap_nocache(&pdev->dev,
+					   res->start, resource_size(res));
+#endif
+	codec->regs_size = res->end - res->start;
+
+	if (IS_ERR(codec->regs)) {
+		dev_err(&pdev->dev, "Can't map registers");
+		err = PTR_ERR(codec->regs);
+		goto fail;
+	}
+
+	mem_node = of_parse_phandle(pdev->dev.of_node, "memory-region", 0);
+	if (mem_node) {
+		err = of_address_to_resource(mem_node, 0, &mem_res);
+
+		if (!err) {
+			err = of_reserved_mem_device_init(&pdev->dev);
+			if (err) {
+				dev_err(&pdev->dev, "Failed to get shared dma pool with error : %d\n", err);
+			} else {
+				dev_dbg(&pdev->dev, "Using shared dma pool for allocation\n");
+				err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+				if (err) {
+					dev_err(&pdev->dev, "dma_set_coherent_mask: %d\n", err);
+					goto fail_mem;
+				}
+
+#ifdef CONFIG_MEMORY_HOTPLUG
+			/* Hotplug requires 0x40000000 alignment so round to nearest multiple */
+			if (resource_size(&mem_res) % HOTPLUG_ALIGN)
+				pgtable_padding = HOTPLUG_ALIGN -
+					(resource_size(&mem_res) % HOTPLUG_ALIGN);
+			else
+				pgtable_padding = 0;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 10, 0)
+			add_memory(0, mem_res.start, resource_size(&mem_res) +
+					   pgtable_padding, MHP_NONE);
+#else
+			add_memory(0, mem_res.start, resource_size(&mem_res) +
+					   pgtable_padding);
+#endif
+#endif
+			}
+		}
+	}
+	of_node_put(mem_node);
+
+	config.cmd_base = (unsigned long)codec->regs + MAILBOX_CMD;
+	config.cmd_size = MAILBOX_SIZE;
+	config.status_base = (unsigned long)codec->regs + MAILBOX_STATUS;
+	config.status_size = MAILBOX_SIZE;
+
+	err = al5_mcu_interface_create(&mcu, codec->device, &config,
+				       codec->regs + AL5_MCU_INTERRUPT);
+	if (err) {
+		dev_err(&pdev->dev, "Can't create interface with mcu");
+		goto fail_mem;
+	}
+
+	al5_group_init(&codec->users_group, mcu, max_users_nb, codec->device);
+
+	err = alloc_mcu_caches(codec);
+	if (err) {
+		dev_err(&pdev->dev, "icache failed to be allocated");
+		goto fail_mem;
+	}
+
+	err = devm_request_threaded_irq(codec->device,
+					irq,
+					al5_hardirq_handler,
+					al5_irq_handler,
+					IRQF_SHARED, device_name, codec);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to request IRQ #%d -> :%d",
+			irq, err);
+		goto free_mcu_caches;
+	}
+
+	platform_set_drvdata(pdev, codec);
+
+	return 0;
+
+free_mcu_caches:
+	al5_free_dma(codec->device, codec->icache);
+	codec->icache = NULL;
+fail_mem:
+	of_reserved_mem_device_release(codec->device);
+fail:
+	return err;
+
+}
+EXPORT_SYMBOL_GPL(al5_codec_set_up);
+
+void al5_codec_tear_down(struct al5_codec_desc *codec)
+{
+	struct al5_group *group = &codec->users_group;
+
+	al5_mcu_interface_destroy(group->mcu, codec->device);
+	al5_group_deinit(group);
+	al5_free_dma(codec->device, codec->suballoc_buf);
+	al5_free_dma(codec->device, codec->icache);
+	of_reserved_mem_device_release(codec->device);
+}
+EXPORT_SYMBOL_GPL(al5_codec_tear_down);
+
+long al5_codec_compat_ioctl(struct file *file, unsigned int cmd,
+			    unsigned long arg)
+{
+	long ret = -ENOIOCTLCMD;
+
+	if (file->f_op->unlocked_ioctl)
+		ret = file->f_op->unlocked_ioctl(file, cmd, arg);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(al5_codec_compat_ioctl);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_codec_mails.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_codec_mails.c
@@ -0,0 +1,94 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/printk.h>
+
+#include "al_codec_mails.h"
+#include "al_ioctl.h"
+#include "al_traces.h"
+
+const u32 uid_size = 4;
+struct al5_mail *create_init_msg(u32 chan_uid, struct mcu_init_msg *msg)
+{
+	struct al5_mail *mail;
+
+	mail = al5_mail_create(AL_MCU_MSG_INIT, uid_size + sizeof(*msg));
+	if (!mail)
+		return NULL;
+	al5_mail_write_word(mail, chan_uid);
+	al5_mail_write(mail, msg, sizeof(*msg));
+
+	return mail;
+}
+
+struct al5_mail *create_destroy_channel_msg(u32 chan_uid)
+{
+	return al5_create_empty_mail(chan_uid, AL_MCU_MSG_DESTROY_CHANNEL);
+}
+
+struct al5_mail *create_quiet_destroy_channel_msg(u32 chan_uid)
+{
+	return al5_create_empty_mail(chan_uid,
+				     AL_MCU_MSG_QUIET_DESTROY_CHANNEL);
+}
+
+struct al5_mail *al5_create_empty_mail(u32 sender_uid, u32 msg_uid)
+{
+	struct al5_mail *mail = al5_mail_create(msg_uid, uid_size);
+
+	al5_mail_write_word(mail, sender_uid);
+	return mail;
+}
+EXPORT_SYMBOL_GPL(al5_create_empty_mail);
+struct al5_mail *al5_create_classic_mail(u32 sender_uid, u32 msg_uid, void *msg,
+					 u32 msg_size)
+{
+	struct al5_mail *mail;
+
+	mail = al5_mail_create(msg_uid, uid_size + msg_size);
+	if (!mail)
+		return NULL;
+	al5_mail_write_word(mail, sender_uid);
+	al5_mail_write(mail, msg, msg_size);
+
+	return mail;
+}
+EXPORT_SYMBOL_GPL(al5_create_classic_mail);
+
+
+u32 al5_mail_get_chan_uid(struct al5_mail *mail)
+{
+	u32 mail_uid = al5_mail_get_uid(mail);
+
+	switch (mail_uid) {
+	case AL_MCU_MSG_INIT:
+	case AL_MCU_MSG_SEARCH_START_CODE:
+	case AL_MCU_MSG_TRACE:
+		pr_err("assert: mail of uid %d doesn't have a chan_uid\n",
+		       mail_uid);
+		return -1;
+	default:
+		return al5_mail_get_word(mail, 0);
+	}
+}
+EXPORT_SYMBOL_GPL(al5_mail_get_chan_uid);
+
+void al5_print_mcu_trace(struct al5_mail *mail)
+{
+	mcu_info("Mcu trace: %s", (char *)al5_mail_get_body(mail));
+}
+EXPORT_SYMBOL_GPL(al5_print_mcu_trace);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_dmabuf.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_dmabuf.c
@@ -0,0 +1,418 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include "al_dmabuf.h"
+
+#include <linux/uaccess.h>
+#include <linux/dma-buf.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Kevin Grandemange");
+MODULE_AUTHOR("Sebastien Alaiwan");
+MODULE_AUTHOR("Antoine Gruzelle");
+MODULE_DESCRIPTION("Allegro Common");
+
+struct al5_dmabuf_priv {
+	struct al5_dma_buffer *buffer;
+
+	/* DMABUF related */
+	struct device *dev;
+	struct sg_table *sgt_base;
+	enum dma_data_direction dma_dir;
+};
+
+struct al5_dmabuf_attachment {
+	struct sg_table sgt;
+	enum dma_data_direction dma_dir;
+};
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 19, 0)
+/* device argument was removed */
+static int al5_dmabuf_attach(struct dma_buf *dbuf, struct dma_buf_attachment *dbuf_attach)
+#else
+static int al5_dmabuf_attach(struct dma_buf *dbuf, struct device *dev,
+			     struct dma_buf_attachment *dbuf_attach)
+#endif
+{
+	struct al5_dmabuf_priv *dinfo = dbuf->priv;
+	struct al5_dmabuf_attachment *attach;
+
+	struct scatterlist *rd, *wr;
+	struct sg_table *sgt;
+	int ret, i;
+
+	attach = kzalloc(sizeof(*attach), GFP_KERNEL);
+	if (!attach)
+		return -ENOMEM;
+
+	sgt = &attach->sgt;
+
+	ret = sg_alloc_table(sgt, dinfo->sgt_base->orig_nents, GFP_KERNEL);
+	if (ret) {
+		kfree(attach);
+		return -ENOMEM;
+	}
+
+	rd = dinfo->sgt_base->sgl;
+	wr = sgt->sgl;
+
+	for (i = 0; i < sgt->orig_nents; ++i) {
+		sg_set_page(wr, sg_page(rd), rd->length, rd->offset);
+		/* map the scatter gather list. As the mapping is coherent we only add
+		 * the dma address and the dma length in the scatterlist without doing
+		 * the costly cache invalidation */
+		sg_dma_address(wr) = dinfo->buffer->dma_handle;
+		sg_dma_len(wr) = rd->length;
+		rd = sg_next(rd);
+		wr = sg_next(wr);
+	}
+
+	attach->dma_dir = DMA_NONE;
+
+	dbuf_attach->priv = attach;
+
+	return 0;
+}
+
+static void al5_dmabuf_detach(struct dma_buf *dbuf,
+			      struct dma_buf_attachment *db_attach)
+{
+	struct al5_dmabuf_attachment *attach = db_attach->priv;
+	struct sg_table *sgt;
+
+	if (!attach)
+		return;
+
+	sgt = &attach->sgt;
+
+	sg_free_table(sgt);
+	kfree(attach);
+	db_attach->priv = NULL;
+}
+
+static struct sg_table *al5_dmabuf_map(struct dma_buf_attachment *db_attach,
+				       enum dma_data_direction dma_dir)
+{
+	struct al5_dmabuf_attachment *attach = db_attach->priv;
+	struct sg_table *sgt;
+	struct mutex *lock = &db_attach->dmabuf->lock;
+
+	mutex_lock(lock);
+
+	sgt = &attach->sgt;
+
+	if (attach->dma_dir == dma_dir) {
+		mutex_unlock(lock);
+		return sgt;
+	}
+
+	attach->dma_dir = dma_dir;
+
+	mutex_unlock(lock);
+
+	return sgt;
+}
+
+static void al5_dmabuf_unmap(struct dma_buf_attachment *at,
+			     struct sg_table *sg, enum dma_data_direction dir)
+{
+}
+
+static int al5_dmabuf_mmap(struct dma_buf *buf, struct vm_area_struct *vma)
+{
+	struct al5_dmabuf_priv *dinfo = buf->priv;
+	unsigned long start = vma->vm_start;
+	unsigned long vsize = vma->vm_end - start;
+	struct al5_dma_buffer *buffer = dinfo->buffer;
+	int ret;
+
+	if (!dinfo) {
+		pr_err("No buffer to map\n");
+		return -EINVAL;
+	}
+
+	vma->vm_pgoff = 0;
+
+	ret = dma_mmap_coherent(dinfo->dev, vma, buffer->cpu_handle,
+				buffer->dma_handle, vsize);
+
+	if (ret < 0) {
+		pr_err("Remapping memory failed, error: %d\n", ret);
+		return ret;
+	}
+
+	vma->vm_flags |= VM_DONTEXPAND | VM_DONTDUMP;
+
+	return 0;
+}
+
+static void al5_dmabuf_release(struct dma_buf *buf)
+{
+	struct al5_dmabuf_priv *dinfo = buf->priv;
+	struct al5_dma_buffer *buffer = dinfo->buffer;
+
+	if (dinfo->sgt_base) {
+		sg_free_table(dinfo->sgt_base);
+		kfree(dinfo->sgt_base);
+	}
+
+
+	dma_free_coherent(dinfo->dev, buffer->size, buffer->cpu_handle,
+			  buffer->dma_handle);
+
+	put_device(dinfo->dev);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 9, 0)
+	kfree_sensitive(buffer);
+#else
+	kzfree(buffer);
+#endif
+	kfree(dinfo);
+}
+
+static void *al5_dmabuf_kmap(struct dma_buf *dmabuf, unsigned long page_num)
+{
+	struct al5_dmabuf_priv *dinfo = dmabuf->priv;
+	void *vaddr = dinfo->buffer->cpu_handle;
+
+	return vaddr + page_num * PAGE_SIZE;
+}
+
+#if LINUX_VERSION_CODE > KERNEL_VERSION(5, 10, 0)
+static int al5_dmabuf_vmap(struct dma_buf *dbuf, struct dma_buf_map *map)
+#else
+static void *al5_dmabuf_vmap(struct dma_buf *dbuf)
+#endif
+{
+	struct al5_dmabuf_priv *dinfo = dbuf->priv;
+	void *vaddr = dinfo->buffer->cpu_handle;
+
+#if LINUX_VERSION_CODE > KERNEL_VERSION(5, 10, 0)
+	if (!vaddr)
+		return -ENOMEM;
+	dma_buf_map_set_vaddr(map, vaddr);
+
+	return 0;
+#else
+	return vaddr;
+#endif
+}
+
+static const struct dma_buf_ops al5_dmabuf_ops = {
+	.attach		= al5_dmabuf_attach,
+	.detach		= al5_dmabuf_detach,
+	.map_dma_buf	= al5_dmabuf_map,
+	.unmap_dma_buf	= al5_dmabuf_unmap,
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(4, 12, 0)
+/* the map_atomic interface was removed after 4.19 */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(4, 19, 0)
+	.map_atomic	= al5_dmabuf_kmap,
+#endif
+/* the map interface was removed in 5.8 */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(5, 8, 0)
+	.map		= al5_dmabuf_kmap,
+#endif
+#else
+	.kmap_atomic	= al5_dmabuf_kmap,
+	.kmap		= al5_dmabuf_kmap,
+#endif
+	.vmap		= al5_dmabuf_vmap,
+	.mmap		= al5_dmabuf_mmap,
+	.release	= al5_dmabuf_release,
+};
+
+static void define_export_info(struct dma_buf_export_info *exp_info,
+			       size_t size,
+			       void *priv)
+{
+	exp_info->owner = THIS_MODULE;
+	exp_info->exp_name = KBUILD_MODNAME;
+	exp_info->ops = &al5_dmabuf_ops;
+	exp_info->flags = O_RDWR;
+	exp_info->resv = NULL;
+	exp_info->size = size;
+	exp_info->priv = priv;
+}
+
+static struct sg_table *al5_get_base_sgt(struct al5_dmabuf_priv *dinfo)
+{
+	int ret;
+	struct sg_table *sgt;
+	struct al5_dma_buffer *buf = dinfo->buffer;
+	struct device *dev = dinfo->dev;
+
+	sgt = kzalloc(sizeof(*sgt), GFP_KERNEL);
+	if (!sgt)
+		return NULL;
+
+	ret = dma_get_sgtable(dev, sgt, buf->cpu_handle, buf->dma_handle,
+			      buf->size);
+	if (ret < 0) {
+		kfree(sgt);
+		return NULL;
+	}
+
+	return sgt;
+
+}
+
+static struct dma_buf *al5_get_dmabuf(void *dma_info_priv)
+{
+	struct dma_buf *dbuf;
+	struct dma_buf_export_info exp_info;
+
+	struct al5_dmabuf_priv *dinfo = dma_info_priv;
+
+	struct al5_dma_buffer *buf = dinfo->buffer;
+
+	define_export_info(&exp_info,
+			   buf->size,
+			   (void *)dinfo);
+
+	if (!dinfo->sgt_base)
+		dinfo->sgt_base = al5_get_base_sgt(dinfo);
+
+	if (WARN_ON(!dinfo->sgt_base))
+		return NULL;
+
+	dbuf = dma_buf_export(&exp_info);
+	if (IS_ERR(dbuf)) {
+		pr_err("couldn't export dma buf\n");
+		return NULL;
+	}
+
+	return dbuf;
+}
+
+void *al5_dmabuf_wrap(struct device *dev, size_t size,
+		      struct al5_dma_buffer *buffer)
+{
+	struct al5_dmabuf_priv *dinfo;
+	struct dma_buf *dbuf;
+
+	dinfo = kzalloc(sizeof(*dinfo), GFP_KERNEL);
+	if (!dinfo)
+		return ERR_PTR(-ENOMEM);
+
+	dinfo->dev = get_device(dev);
+	dinfo->buffer = buffer;
+	dinfo->dma_dir = DMA_BIDIRECTIONAL;
+	dinfo->sgt_base = al5_get_base_sgt(dinfo);
+
+	dbuf = al5_get_dmabuf(dinfo);
+	if (IS_ERR_OR_NULL(dbuf))
+		return ERR_PTR(-EINVAL);
+
+	return dbuf;
+}
+EXPORT_SYMBOL_GPL(al5_dmabuf_wrap);
+
+int al5_create_dmabuf_fd(struct device *dev, size_t size,
+			 struct al5_dma_buffer *buffer)
+{
+	struct dma_buf *dbuf = al5_dmabuf_wrap(dev, size, buffer);
+
+	if (IS_ERR(dbuf))
+		return PTR_ERR(dbuf);
+	return dma_buf_fd(dbuf, O_RDWR);
+}
+EXPORT_SYMBOL_GPL(al5_create_dmabuf_fd);
+
+int al5_allocate_dmabuf(struct device *dev, size_t size, u32 *fd)
+{
+	struct al5_dma_buffer *buffer;
+
+	buffer = al5_alloc_dma(dev, size);
+	if (!buffer) {
+		dev_err(dev, "Can't alloc DMA buffer of size %ld", size);
+		return -ENOMEM;
+	}
+
+	*fd = al5_create_dmabuf_fd(dev, size, buffer);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_allocate_dmabuf);
+
+int al5_get_dmabuf_info(struct device *dev, u32 fd,
+			struct al5_buffer_info *info)
+{
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	int err = 0;
+
+	dbuf = dma_buf_get(fd);
+	if (IS_ERR(dbuf))
+		return -EINVAL;
+	attach = dma_buf_attach(dbuf, dev);
+	if (IS_ERR(attach)) {
+		err = -EINVAL;
+		goto fail_attach;
+	}
+	sgt = dma_buf_map_attachment(attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR(sgt)) {
+		err = -EINVAL;
+		goto fail_map;
+	}
+
+	info->bus_address = sg_dma_address(sgt->sgl);
+	info->size = dbuf->size;
+
+	dma_buf_unmap_attachment(attach, sgt, DMA_BIDIRECTIONAL);
+fail_map:
+	dma_buf_detach(dbuf, attach);
+fail_attach:
+	dma_buf_put(dbuf);
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5_get_dmabuf_info);
+
+int al5_dmabuf_get_address(struct device *dev, u32 fd, u32 *bus_address)
+{
+	struct dma_buf *dbuf;
+	struct dma_buf_attachment *attach;
+	struct sg_table *sgt;
+	int err = 0;
+
+	dbuf = dma_buf_get(fd);
+	if (IS_ERR(dbuf))
+		return -EINVAL;
+	attach = dma_buf_attach(dbuf, dev);
+	if (IS_ERR(attach)) {
+		err = -EINVAL;
+		goto fail_attach;
+	}
+	sgt = dma_buf_map_attachment(attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR(sgt)) {
+		err = -EINVAL;
+		goto fail_map;
+	}
+
+	*bus_address = sg_dma_address(sgt->sgl);
+
+	dma_buf_unmap_attachment(attach, sgt, DMA_BIDIRECTIONAL);
+fail_map:
+	dma_buf_detach(dbuf, attach);
+fail_attach:
+	dma_buf_put(dbuf);
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5_dmabuf_get_address);
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_group.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_group.c
@@ -0,0 +1,258 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/slab.h>
+#include <linux/printk.h>
+#include <linux/string.h>
+
+#include "al_group.h"
+#include "al_mail.h"
+#include "al_codec_mails.h"
+#include "al_constants.h"
+
+void al5_group_init(struct al5_group *group, struct mcu_mailbox_interface *mcu,
+		    int max_users_nb, struct device *device)
+{
+	group->users = kcalloc(max_users_nb, sizeof(void *), GFP_KERNEL);
+	group->max_users_nb = max_users_nb;
+	spin_lock_init(&group->lock);
+	group->mcu = mcu;
+	group->device = device;
+}
+
+void al5_user_destroy_channel_resources(struct al5_user *user);
+void al5_group_deinit(struct al5_group *group)
+{
+	kfree(group->users);
+}
+
+int al5_group_bind_user(struct al5_group *group, struct al5_user *user)
+{
+	unsigned long flags = 0;
+	int uid = -1;
+	int err = 0;
+	int i;
+
+	spin_lock_irqsave(&group->lock, flags);
+	for (i = 0; i < group->max_users_nb; ++i) {
+		if (group->users[i] == NULL) {
+			uid = i;
+			break;
+		}
+	}
+	if (uid == -1) {
+		dev_err(group->device, "Max user allocation reached\n");
+		err = -EAGAIN;
+		goto unlock;
+	}
+
+	group->users[uid] = user;
+	al5_user_init(user, uid, group->mcu, group->device);
+
+unlock:
+	spin_unlock_irqrestore(&group->lock, flags);
+	return err;
+
+}
+EXPORT_SYMBOL_GPL(al5_group_bind_user);
+
+void al5_group_unbind_user(struct al5_group *group, struct al5_user *user)
+{
+	unsigned long flags = 0;
+
+	spin_lock_irqsave(&group->lock, flags);
+	group->users[user->uid] = NULL;
+	spin_unlock_irqrestore(&group->lock, flags);
+}
+EXPORT_SYMBOL_GPL(al5_group_unbind_user);
+
+struct al5_user *al5_group_user_from_uid(struct al5_group *group, int user_uid)
+{
+	struct al5_user *user;
+
+	if (user_uid >= group->max_users_nb || user_uid < 0) {
+		dev_err(group->device,
+			"Received user id %d, expected a value in [0..%ld]\n",
+			user_uid, (unsigned long)group->max_users_nb);
+		user = NULL;
+	} else
+		user = group->users[user_uid];
+
+	return user;
+}
+EXPORT_SYMBOL_GPL(al5_group_user_from_uid);
+
+static bool hasChannelId(struct al5_user *user, int channel_id)
+{
+	return user != NULL && user->chan_uid == channel_id;
+}
+
+struct al5_user *al5_group_user_from_chan_uid(struct al5_group *group,
+					      int chan_uid)
+{
+	int i;
+
+	for (i = 0; i < group->max_users_nb; ++i)
+		if (hasChannelId(group->users[i], chan_uid))
+			return group->users[i];
+
+	dev_err(group->device, "Received chan_uid %d. No corresponding channel",
+		chan_uid);
+
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(al5_group_user_from_chan_uid);
+
+static void destroy_orphan_channel(struct al5_group *group, int chan_uid)
+{
+	int err;
+	struct al5_mail *mail;
+
+	mail = create_quiet_destroy_channel_msg(chan_uid);
+	if (!mail)
+		goto fail;
+
+	err = al5_mcu_send(group->mcu, mail);
+	if (err)
+		goto fail_send;
+
+	al5_signal_mcu(group->mcu);
+	al5_free_mail(mail);
+	return;
+
+fail_send:
+	al5_free_mail(mail);
+fail:
+	dev_err(group->device, "Couldn't destroy orphan mcu channel\n");
+}
+
+void print_cannot_retrieve_user(struct device *dev, u32 mail_uid)
+{
+	dev_err(dev, "Mail of uid %d received related to inexistant user\n",
+		mail_uid);
+}
+
+bool should_destroy_channel_on_bad_feedback(u32 mail_uid)
+{
+	switch (mail_uid) {
+	case AL_MCU_MSG_INIT:
+	case AL_MCU_MSG_SEARCH_START_CODE:
+	case AL_MCU_MSG_DESTROY_CHANNEL:
+		return false;
+	default:
+		return true;
+	}
+}
+
+struct al5_user *retrieve_user(struct al5_group *group, struct al5_mail *mail)
+{
+	struct al5_user *user;
+	int user_uid, chan_uid = BAD_CHAN;
+
+	switch (al5_mail_get_uid(mail)) {
+
+	case AL_MCU_MSG_CREATE_CHANNEL:
+		user_uid = al5_mail_get_word(mail, 1);
+		user = al5_group_user_from_uid(group, user_uid);
+		break;
+	case AL_MCU_MSG_INIT:
+	case AL_MCU_MSG_SEARCH_START_CODE:
+		user_uid = al5_mail_get_word(mail, 0);
+		user = al5_group_user_from_uid(group, user_uid);
+		break;
+	default:
+		chan_uid = al5_mail_get_word(mail, 0);
+		user = al5_group_user_from_chan_uid(group, chan_uid);
+		break;
+	}
+	return user;
+}
+
+/* return -1 if we failed to retrieve the user, -ENOMEM if there was a memory
+ * shortage and 0 otherwhise */
+#define AL_NO_USER -1
+int try_to_deliver_to_user(struct al5_group *group, struct al5_mail *mail)
+{
+	struct al5_user *user;
+	int ret = AL_NO_USER;
+	u32 mail_uid = al5_mail_get_uid(mail);
+
+	spin_lock(&group->lock);
+	user = retrieve_user(group, mail);
+
+        if (user == NULL) {
+		print_cannot_retrieve_user(group->device, al5_mail_get_uid(mail));
+		goto unlock;
+	}
+
+	if (mail_uid == AL_MCU_MSG_DESTROY_CHANNEL)
+		user->chan_uid = BAD_CHAN;
+
+	if (mail_uid == AL_MCU_MSG_CREATE_CHANNEL)
+		user->chan_uid = al5_mail_get_chan_uid(mail);
+
+	ret = al5_user_deliver(user, mail);
+
+unlock:
+	spin_unlock(&group->lock);
+	return ret;
+}
+
+void handle_mail(struct al5_group *group, struct al5_mail *mail)
+{
+	int error;
+	u32 mail_uid = al5_mail_get_uid(mail);
+
+	if (mail_uid == AL_MCU_MSG_TRACE) {
+		al5_print_mcu_trace(mail);
+		al5_free_mail(mail);
+		return;
+	}
+
+	error = try_to_deliver_to_user(group, mail);
+	if (error == AL_NO_USER) {
+		if (should_destroy_channel_on_bad_feedback(mail_uid))
+			destroy_orphan_channel(group, al5_mail_get_chan_uid(mail));
+		al5_free_mail(mail);
+	}else if (error == -ENOMEM)
+		dev_err(group->device,
+			"Failed to deliver mail to the user (memory shortage). Skipping...\n");
+}
+
+void read_mail(struct al5_group *group)
+{
+	struct al5_mail *mail = al5_mcu_recv(group->mcu);
+
+	if (!mail) {
+		dev_err(group->device, "Failed to get mcu mail. Skipping...\n");
+		return;
+	}
+
+	handle_mail(group, mail);
+}
+
+/* A message contains at least a header (2 u16).
+   We compute the upper bound of the message number
+   to check if the mailbox is broken and stop looping if it is */
+#define MAX_MAILBOX_MSG (MAILBOX_SIZE / 4)
+void al5_group_read_mails(struct al5_group *group)
+{
+	unsigned nb_msg = 0;
+
+	while (!al5_mcu_is_empty(group->mcu) && nb_msg++ < MAX_MAILBOX_MSG)
+		read_mail(group);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_l2_prefetch.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_l2_prefetch.c
@@ -0,0 +1,42 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/types.h>
+
+u32 get_l2_color_bitdepth(void *parent)
+{
+	(void)parent;
+	return -1;
+}
+
+u32 get_l2_size_in_bits(void *parent)
+{
+	(void)parent;
+	return -1;
+}
+
+u32 get_num_cores(void *parent)
+{
+	(void)parent;
+	return -1;
+}
+
+u32 get_core_frequency(void *parent)
+{
+	(void)parent;
+	return -1;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_list.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_list.c
@@ -0,0 +1,81 @@
+/*
+ * al_list.c
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "al_list.h"
+#include <linux/slab.h>
+
+void al5_list_init(struct al5_list **l)
+{
+	*l = NULL;
+}
+
+int al5_list_empty(const struct al5_list *l)
+{
+	return l == NULL;
+}
+
+/* return -ENOMEM if we failed to create the list object, 0 otherwhise */
+int al5_list_push(struct al5_list **l, struct al5_mail *mail)
+{
+	struct al5_list *first_pos = *l;
+
+	if (*l == NULL) {
+		*l = kmalloc(sizeof(**l), GFP_NOWAIT);
+		if (*l == NULL)
+			return -ENOMEM;
+		(*l)->mail = mail;
+		(*l)->next = NULL;
+		return 0;
+	}
+	while ((*l)->next != NULL)
+		*l = (*l)->next;
+	(*l)->next = kmalloc(sizeof(*((*l)->next)), GFP_NOWAIT);
+	if ((*l)->next == NULL)
+		return -ENOMEM;
+	(*l)->next->mail = mail;
+	(*l)->next->next = NULL;
+	*l = first_pos;
+
+	return 0;
+}
+
+struct al5_mail *al5_list_pop(struct al5_list **l)
+{
+	struct al5_mail *mail;
+	struct al5_list *next;
+
+	if (*l == NULL)
+		return NULL;
+
+	mail = (*l)->mail;
+	next = (*l)->next;
+
+	kfree(*l);
+	*l = next;
+	return mail;
+}
+
+void al5_list_empty_and_destroy(struct al5_list **l)
+{
+	while (!al5_list_empty(*l)) {
+		struct al5_mail *mail = al5_list_pop(l);
+
+		al5_free_mail(mail);
+	}
+	kfree(*l);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_mail.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_mail.c
@@ -0,0 +1,112 @@
+/*
+ * al_mail.c create a message to send to the vcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/slab.h>
+#include <linux/string.h>
+
+#include "al_mail.h"
+#include "al_mail_private.h"
+
+static size_t get_mail_struct_size(void)
+{
+	const size_t mail_size = roundup(sizeof(struct al5_mail), 4);
+
+	return mail_size;
+}
+
+/* body should be aligned 32 bits */
+size_t al5_get_mail_alloc_size(u32 content_size)
+{
+	return get_mail_struct_size() + content_size;
+}
+
+void al5_mail_init(struct al5_mail *mail, u32 msg_uid, u32 content_size)
+{
+	mail->body_offset = 0;
+	mail->msg_uid = msg_uid;
+	mail->body_size = content_size;
+	mail->body = (u8 *)mail + get_mail_struct_size();
+}
+
+struct al5_mail *al5_mail_create(u32 msg_uid, u32 content_size)
+{
+	struct al5_mail *mail =
+		kmalloc(al5_get_mail_alloc_size(content_size), GFP_KERNEL);
+
+	if (!mail)
+		return NULL;
+
+	al5_mail_init(mail, msg_uid, content_size);
+
+	return mail;
+}
+EXPORT_SYMBOL_GPL(al5_mail_create);
+
+void al5_mail_write(struct al5_mail *mail, void *content, u32 size)
+{
+	memcpy(mail->body + mail->body_offset, content, size);
+	mail->body_offset += size;
+}
+EXPORT_SYMBOL_GPL(al5_mail_write);
+
+void al5_mail_write_word(struct al5_mail *mail, u32 word)
+{
+	al5_mail_write(mail, &word, 4);
+}
+EXPORT_SYMBOL_GPL(al5_mail_write_word);
+
+void al5_free_mail(struct al5_mail *mail)
+{
+	if (mail != NULL)
+		kfree(mail);
+}
+EXPORT_SYMBOL_GPL(al5_free_mail);
+
+u32 al5_mail_get_uid(struct al5_mail *mail)
+{
+	return mail->msg_uid;
+}
+EXPORT_SYMBOL_GPL(al5_mail_get_uid);
+
+u32 al5_mail_get_size(struct al5_mail *mail)
+{
+	return mail->body_size;
+}
+EXPORT_SYMBOL_GPL(al5_mail_get_size);
+
+void *al5_mail_get_body(struct al5_mail *mail)
+{
+	return mail->body;
+}
+EXPORT_SYMBOL_GPL(al5_mail_get_body);
+
+u32 al5_mail_get_word(struct al5_mail *mail, u32 word_offset)
+{
+	return ((u32 *)(mail->body))[word_offset];
+}
+EXPORT_SYMBOL_GPL(al5_mail_get_word);
+
+struct al5_mail *al5_mail_create_copy(struct al5_mail *mail)
+{
+	struct al5_mail *copy = al5_mail_create(mail->msg_uid, mail->body_size);
+
+	al5_mail_write(copy, mail->body, mail->body_size);
+
+	return copy;
+}
+EXPORT_SYMBOL_GPL(al5_mail_create_copy);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_mailbox.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_mailbox.c
@@ -0,0 +1,199 @@
+/*
+ * al_mailbox.c mailbox mechanisms. r/w messages to/from the mcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/slab.h>
+#include <linux/io.h>
+
+#include "al_mailbox.h"
+#include "al_mail_private.h"
+#include "mcu_utils.h"
+
+const int header_size = 4;
+
+static int not_enough_space_in_mailbox(size_t mailbox_size,
+				       size_t used_size,
+				       size_t data_size)
+{
+	/* Head & Tail can only be multiples of 4,
+	 * and they can only be equals if mailbox is empty
+	 */
+	return data_size + 4 > mailbox_size - used_size;
+}
+
+static int mailbox_is_wrapping(size_t mailbox_size,
+			       unsigned int tail_value,
+			       size_t data_size)
+{
+	return tail_value + data_size > mailbox_size;
+}
+/* Require mailbox_is_wrapping */
+static void write_in_mailbox_until_wrap(struct mailbox *box,
+					size_t *memcpy_size,
+					unsigned int *tail,
+					u8 **data)
+{
+	size_t space_left_before_wrapping = box->size - *tail;
+
+	memcpy_toio_32(box->data + *tail, *data, space_left_before_wrapping);
+	*tail = 0;
+	*memcpy_size -= space_left_before_wrapping;
+	*data += space_left_before_wrapping;
+}
+
+/* Require mailbox_is_wrapping */
+static void read_in_mailbox_until_wrap(struct mailbox *box,
+				       size_t *memcpy_size,
+				       unsigned int *head,
+				       u8 **data)
+{
+
+	size_t space_left_before_wrapping = box->size - *head;
+
+	memcpy_fromio_32(*data, box->data + *head,  space_left_before_wrapping);
+	*head = 0;
+	*memcpy_size -= space_left_before_wrapping;
+	*data += space_left_before_wrapping;
+}
+
+void al5_mailbox_init(struct mailbox *box, void *base, size_t data_size)
+{
+	box->size = data_size;
+	box->head = base;
+	box->tail = base + 4;
+	box->data = base + 8;
+	iowrite32(0, box->head);
+	iowrite32(0, box->tail);
+}
+EXPORT_SYMBOL_GPL(al5_mailbox_init);
+
+static u16 unserialize_msg_uid(u8 *header)
+{
+	return header[2] + (header[3] << 8);
+}
+
+static u16 unserialize_body_size(u8 *header)
+{
+	return header[0] + (header[1] << 8);
+}
+
+static void serialize_header(u8 *header, u16 msg_uid, u16 body_size)
+{
+	header[0] = body_size & 0x00ff;
+	header[1] = body_size >> 8;
+	header[2] = msg_uid & 0x00ff;
+	header[3] = msg_uid >> 8;
+}
+
+static void pull_tail(struct mailbox *box)
+{
+	box->local_tail = ioread32(box->tail);
+}
+
+static void push_tail(struct mailbox *box)
+{
+	iowrite32(box->local_tail, box->tail);
+}
+
+/* Assume there is enough place in mailbox */
+static void write_data(struct mailbox *box, u8 *in_data, size_t size)
+{
+	u32 tail_value = box->local_tail;
+
+	if (mailbox_is_wrapping(box->size, tail_value, size))
+		write_in_mailbox_until_wrap(box,
+					    &size,
+					    &tail_value,
+					    &in_data);
+	memcpy_toio_32(box->data + tail_value, in_data, size);
+
+	tail_value = ((tail_value + size + 3) / 4 * 4) % box->size;
+	box->local_tail = tail_value;
+}
+
+static u8 *read_data(struct mailbox *box, u8 *out_data, size_t size)
+{
+	u32 head_value = ioread32(box->head);
+	u8 *data_iterator = out_data;
+
+	if (mailbox_is_wrapping(box->size, head_value, size))
+		read_in_mailbox_until_wrap(box, &size, &head_value,
+					   &data_iterator);
+
+	memcpy_fromio_32(data_iterator, box->data + head_value, size);
+	head_value = ((head_value + size + 3) / 4 * 4) % box->size;
+	iowrite32(head_value, box->head);
+
+	return out_data;
+}
+
+int al5_mailbox_write(struct mailbox *box, struct al5_mail *mail)
+{
+	u8 header[header_size];
+	size_t mail_size = al5_mail_get_size(mail);
+	size_t total_size = mail_size + header_size;
+	unsigned int head_value = ioread32(box->head);
+	unsigned int tail_value = ioread32(box->tail);
+	size_t mailbox_size = box->size;
+	size_t used_size =
+		(tail_value >= head_value) ? (tail_value - head_value)
+		: (mailbox_size + tail_value - head_value);
+
+	if (not_enough_space_in_mailbox(mailbox_size, used_size, total_size))
+		return -EAGAIN;
+
+	serialize_header(header, al5_mail_get_uid(mail), mail_size);
+
+	pull_tail(box);
+	write_data(box, header, header_size);
+	write_data(box, al5_mail_get_body(mail), mail_size);
+	push_tail(box);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_mailbox_write);
+
+bool al5_mailbox_read(struct mailbox *box, struct al5_mail *mail, size_t mail_size)
+{
+	u8 header[header_size];
+	u16 msg_uid;
+	u16 body_size;
+	size_t real_mail_size;
+
+	read_data(box, header, header_size);
+
+	msg_uid = unserialize_msg_uid(header);
+	body_size = unserialize_body_size(header);
+
+	real_mail_size = al5_get_mail_alloc_size(body_size);
+
+	/* we can't store this mail, it will be dropped */
+	if (mail_size < real_mail_size) {
+		pr_debug(
+			"BUG(%s) mail_size: %ld, real mail_size: %ld, body size: %d, msg uid: %d\n", __func__, mail_size, real_mail_size, body_size,
+			msg_uid);
+		return false;
+	}
+
+	al5_mail_init(mail, msg_uid, body_size);
+
+	read_data(box, mail->body, body_size);
+	/* for consistency, but noone should want to write after this mail */
+	mail->body_offset += body_size;
+	return true;
+}
+EXPORT_SYMBOL_GPL(al5_mailbox_read);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_queue.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_queue.c
@@ -0,0 +1,127 @@
+/*
+ * al_queue.c
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "al_queue.h"
+
+void al5_queue_init(struct al5_queue *q)
+{
+	init_waitqueue_head(&q->queue);
+	spin_lock_init(&q->lock);
+	al5_list_init(&q->list);
+	q->locked = true;
+}
+EXPORT_SYMBOL_GPL(al5_queue_init);
+
+static bool mail_is_available(struct al5_queue *q)
+{
+	return !al5_list_empty(q->list) || !q->locked;
+}
+
+int al5_queue_pop_timeout(struct al5_mail **mail, struct al5_queue *q)
+{
+	unsigned long flags = 0;
+
+	int err = wait_event_interruptible_timeout(q->queue,
+						   mail_is_available(q),
+						   WAIT_TIMEOUT_DURATION);
+
+	/*
+	 * queue has a strict timeout.
+	 * if we get a timeout, it means
+	 * the mcu didn't answer and is in
+	 * a bad state. we do not want to try again
+	 */
+	if (err == 0)
+		err = -EINVAL;
+	else if (err > 0)
+		err = 0;
+	/* errors of queue are transmitted to the userspace so use EINTR */
+	else if (err == -ERESTARTSYS)
+		err = -EINTR;
+
+	spin_lock_irqsave(&q->lock, flags);
+	*mail = al5_list_pop(&q->list);
+	spin_unlock_irqrestore(&q->lock, flags);
+
+	if (*mail)
+		err = 0;
+	else
+		err = (err != 0) ? err : -EINVAL;
+
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5_queue_pop_timeout);
+
+struct al5_mail *al5_queue_pop(struct al5_queue *q)
+{
+	struct al5_mail *mail;
+	unsigned long flags = 0;
+
+	wait_event_interruptible(q->queue, mail_is_available(q));
+	spin_lock_irqsave(&q->lock, flags);
+	mail = al5_list_pop(&q->list);
+	spin_unlock_irqrestore(&q->lock, flags);
+
+	return mail;
+}
+EXPORT_SYMBOL_GPL(al5_queue_pop);
+
+struct al5_mail *al5_queue_pop_no_wait(struct al5_queue *q)
+{
+	struct al5_mail *mail = NULL;
+	unsigned long flags = 0;
+
+	if (mail_is_available(q)) {
+		spin_lock_irqsave(&q->lock, flags);
+		mail = al5_list_pop(&q->list);
+		spin_unlock_irqrestore(&q->lock, flags);
+	}
+
+	return mail;
+}
+EXPORT_SYMBOL_GPL(al5_queue_pop_no_wait);
+
+/* return -ENOME if we failed to push, 0 otherwhise */
+int al5_queue_push(struct al5_queue *q, struct al5_mail *mail)
+{
+	unsigned long flags = 0;
+	int err;
+
+	spin_lock_irqsave(&q->lock, flags);
+	err = al5_list_push(&q->list, mail);
+	spin_unlock_irqrestore(&q->lock, flags);
+
+	wake_up_interruptible(&q->queue);
+
+	return err;
+}
+EXPORT_SYMBOL_GPL(al5_queue_push);
+
+void al5_queue_unlock(struct al5_queue *q)
+{
+	q->locked = false;
+	wake_up_interruptible(&q->queue);
+}
+EXPORT_SYMBOL_GPL(al5_queue_unlock);
+
+void al5_queue_lock(struct al5_queue *q)
+{
+	q->locked = true;
+}
+EXPORT_SYMBOL_GPL(al5_queue_lock);
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_user.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_user.c
@@ -0,0 +1,212 @@
+/*
+ * al_user.c high level function to write messages in the mailbox
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/kernel.h>
+
+#include "al_user.h"
+#include "al_codec_mails.h"
+
+static int mail_to_queue(int mail_uid)
+{
+	switch (mail_uid) {
+	case AL_MCU_MSG_INIT:
+		return AL5_USER_MAIL_INIT;
+	case AL_MCU_MSG_CREATE_CHANNEL:
+		return AL5_USER_MAIL_CREATE;
+	case AL_MCU_MSG_DESTROY_CHANNEL:
+		return AL5_USER_MAIL_DESTROY;
+	case AL_MCU_MSG_ENCODE_ONE_FRM:
+	case AL_MCU_MSG_DECODE_ONE_FRM:
+		return AL5_USER_MAIL_STATUS;
+	case AL_MCU_MSG_SEARCH_START_CODE:
+		return AL5_USER_MAIL_SC;
+	case AL_MCU_MSG_GET_RECONSTRUCTED_PICTURE:
+	case AL_MCU_MSG_RELEASE_RECONSTRUCTED_PICTURE:
+		return AL5_USER_MAIL_REC;
+	default:
+		return AL5_USER_MAIL_DEBUG;
+	}
+}
+
+static int send_msg(struct mcu_mailbox_interface *mcu, struct al5_mail *mail)
+{
+	int err = al5_mcu_send(mcu, mail);
+
+	if (err)
+		return err;
+
+	al5_signal_mcu(mcu);
+
+	return 0;
+}
+
+int al5_check_and_send(struct al5_user *user, struct al5_mail *mail)
+{
+	int err;
+
+	if (!mail)
+		return -ENOMEM;
+	err = send_msg(user->mcu, mail);
+	al5_free_mail(mail);
+	if (err)
+		return err;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_check_and_send);
+
+/* return -ENOMEM if we failed to deliver, 0 otherwhise */
+int al5_user_deliver(struct al5_user *user, struct al5_mail *mail)
+{
+	struct al5_queue *queue =
+		&user->queues[mail_to_queue(al5_mail_get_uid(mail))];
+
+	return al5_queue_push(queue, mail);
+}
+
+static void user_queues_unlock(struct al5_user *user)
+{
+	al5_queue_unlock(&user->queues[AL5_USER_MAIL_STATUS]);
+	al5_queue_unlock(&user->queues[AL5_USER_MAIL_SC]);
+	al5_queue_unlock(&user->queues[AL5_USER_MAIL_CREATE]);
+	al5_queue_unlock(&user->queues[AL5_USER_MAIL_REC]);
+}
+
+static void user_queues_lock(struct al5_user *user)
+{
+	al5_queue_lock(&user->queues[AL5_USER_MAIL_STATUS]);
+	al5_queue_lock(&user->queues[AL5_USER_MAIL_SC]);
+	al5_queue_lock(&user->queues[AL5_USER_MAIL_CREATE]);
+	al5_queue_lock(&user->queues[AL5_USER_MAIL_REC]);
+}
+
+void al5_user_remove_residual_messages(struct al5_user *user)
+{
+	int queue_id;
+
+	for (queue_id = 0; queue_id < AL5_USER_MAIL_NUMBER; ++queue_id) {
+		struct al5_queue *q = &user->queues[queue_id];
+		struct al5_mail *mail;
+
+		al5_queue_unlock(q);
+		mail = al5_queue_pop(q);
+
+		while (mail) {
+			al5_free_mail(mail);
+			mail = al5_queue_pop(q);
+		}
+	}
+}
+
+void al5_user_init(struct al5_user *user, int uid,
+		   struct mcu_mailbox_interface *mcu, struct device *device)
+{
+	int i;
+
+	memset(user, 0, sizeof(*user));
+	for (i = 0; i < AL5_USER_OPS_NUMBER; ++i)
+		mutex_init(&user->locks[i]);
+	for (i = 0; i < AL5_USER_MAIL_NUMBER; ++i)
+		al5_queue_init(&user->queues[i]);
+	user->uid = uid;
+	user->mcu = mcu;
+	user->chan_uid = BAD_CHAN;
+	user->checkpoint = NO_CHECKPOINT;
+	user->device = device;
+	al5_bufpool_init(&user->int_buffers);
+	al5_bufpool_init(&user->rec_buffers);
+}
+EXPORT_SYMBOL_GPL(al5_user_init);
+
+void al5_user_destroy_channel_resources(struct al5_user *user)
+{
+	al5_bufpool_free(&user->int_buffers, user->device);
+	al5_bufpool_free(&user->rec_buffers, user->device);
+}
+
+int al5_user_destroy_channel(struct al5_user *user, int quiet)
+{
+	int err = 0;
+	int i, j;
+	struct al5_mail *mail;
+
+	// Destroy the channel if it was created
+	if (user->checkpoint == NO_CHECKPOINT)
+		return -EPERM;
+
+	user_queues_unlock(user);
+	for (i = 0; i < AL5_USER_OPS_NUMBER; ++i) {
+		err = mutex_lock_killable(&user->locks[i]);
+		if (err == -EINTR) {
+			for (j = 0; j < i; ++j)
+				mutex_unlock(&user->locks[j]);
+
+			goto relock_user_queues;
+		}
+	}
+
+	if (quiet) {
+		err = al5_check_and_send(user,
+					 create_quiet_destroy_channel_msg(
+						 user->chan_uid));
+		if (err)
+			goto unlock_mutexes;
+	} else {
+		err = al5_check_and_send(user, create_destroy_channel_msg(
+						 user->chan_uid));
+		if (err)
+			goto unlock_mutexes;
+
+		mail = al5_queue_pop(&user->queues[AL5_USER_MAIL_DESTROY]);
+		if (mail == NULL) {
+			err = -EINTR;
+			goto unlock_mutexes;
+		}
+
+		al5_free_mail(mail);
+	}
+
+	user->checkpoint = CHECKPOINT_DESTROYED;
+	al5_user_destroy_channel_resources(user);
+
+unlock_mutexes:
+	for (i = 0; i < AL5_USER_OPS_NUMBER; ++i)
+		mutex_unlock(&user->locks[i]);
+relock_user_queues:
+	user_queues_lock(user);
+	return err;
+
+}
+EXPORT_SYMBOL_GPL(al5_user_destroy_channel);
+
+int al5_chan_is_created(struct al5_user *user)
+{
+	return user->checkpoint == CHECKPOINT_CREATED;
+}
+EXPORT_SYMBOL_GPL(al5_chan_is_created);
+
+struct al5_mail *al5_user_get_mail(struct al5_user *user, u32 mail_uid)
+{
+	struct al5_mail *mail;
+	u32 queue_uid = mail_to_queue(mail_uid);
+
+	al5_queue_unlock(&user->queues[queue_uid]);
+	mail = al5_queue_pop(&user->queues[queue_uid]);
+	al5_queue_lock(&user->queues[queue_uid]);
+
+	return mail;
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/al_vcu.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/al_vcu.c
@@ -0,0 +1,52 @@
+/*
+ * al_vcu.c handle communication with mcu via interrupts
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "al_vcu.h"
+#include "al_codec.h"
+#include "al_group.h"
+
+#define AL5_MCU_IRQ_STA 0x910C
+
+irqreturn_t al5_hardirq_handler(int irq, void *data)
+{
+	struct al5_codec_desc *codec = (struct al5_codec_desc *)data;
+	u32 irq_status = al5_readl(AL5_MCU_IRQ_STA);
+
+	if (irq_status == 0)
+		return IRQ_NONE;
+
+	al5_writel(irq_status, AL5_MCU_INTERRUPT_CLR);
+
+	/* wait for the interrupt acknowledgment to propagate in the hw */
+	al5_readl(AL5_MCU_IRQ_STA);
+
+	return IRQ_WAKE_THREAD;
+}
+EXPORT_SYMBOL_GPL(al5_hardirq_handler);
+
+irqreturn_t al5_irq_handler(int irq, void *data)
+{
+	struct al5_codec_desc *codec = (struct al5_codec_desc *)data;
+
+	irq_info("Got irq from Mcu");
+	al5_group_read_mails(&codec->users_group);
+
+	return IRQ_HANDLED;
+}
+EXPORT_SYMBOL_GPL(al5_irq_handler);
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/mcu_interface.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/mcu_interface.c
@@ -0,0 +1,122 @@
+/*
+ * mcu_interface.c mcu interface of the vcu. implements access control to the
+ * mailbox and the protocol to signal a message was sent to the mcu.
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "mcu_interface_private.h"
+#include "mcu_utils.h"
+#include "al_mail_private.h"
+
+#include <linux/printk.h>
+
+int al5_mcu_interface_create(struct mcu_mailbox_interface **mcu,
+			     struct device *device,
+			     struct mcu_mailbox_config *config,
+			     void *mcu_interrupt_register)
+{
+	*mcu = devm_kmalloc(device, sizeof(struct mcu_mailbox_interface), GFP_KERNEL);
+	if (!*mcu)
+		return -ENOMEM;
+
+	al5_mailbox_init(&(*mcu)->cpu_to_mcu, (void *)config->cmd_base,
+			 config->cmd_size);
+	al5_mailbox_init(&(*mcu)->mcu_to_cpu, (void *)config->status_base,
+			 config->status_size);
+	spin_lock_init(&(*mcu)->read_lock);
+	spin_lock_init(&(*mcu)->write_lock);
+	(*mcu)->interrupt_register = mcu_interrupt_register;
+	(*mcu)->dev = device;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(al5_mcu_interface_create);
+
+void al5_mcu_interface_destroy(struct mcu_mailbox_interface *mcu,
+			       struct device *device)
+{
+	devm_kfree(device, mcu);
+}
+EXPORT_SYMBOL_GPL(al5_mcu_interface_destroy);
+
+/* These functions call mailbox methods */
+
+int al5_mcu_send(struct mcu_mailbox_interface *mcu, struct al5_mail *mail)
+{
+	int error;
+
+	spin_lock(&mcu->write_lock);
+	error = al5_mailbox_write(&mcu->cpu_to_mcu, mail);
+	spin_unlock(&mcu->write_lock);
+
+	if (error)
+		dev_warn_ratelimited(mcu->dev, "mailbox is full, retry");
+
+	return error;
+}
+EXPORT_SYMBOL_GPL(al5_mcu_send);
+
+struct al5_mail *al5_mcu_recv(struct mcu_mailbox_interface *mcu)
+{
+	/* this is also the maximum size of the al5_params opaque struct */
+	const size_t mail_size = al5_get_mail_alloc_size(128 * 4);
+	struct al5_mail *mail = kmalloc(mail_size, GFP_KERNEL);
+
+	if (!mail)
+		return NULL;
+
+	spin_lock(&mcu->read_lock);
+	if (!al5_mailbox_read(&mcu->mcu_to_cpu, mail, mail_size)) {
+		dev_err(mcu->dev,
+			"BUG: mcu sent a message bigger than the maximum size.");
+		kfree(mail);
+		mail = NULL;
+	}
+
+	spin_unlock(&mcu->read_lock);
+
+	return mail;
+}
+EXPORT_SYMBOL_GPL(al5_mcu_recv);
+
+int al5_mcu_is_empty(struct mcu_mailbox_interface *mcu)
+{
+	struct mailbox *mailbox = &mcu->mcu_to_cpu;
+	u32 head_value;
+	u32 tail_value;
+
+	spin_lock(&mcu->read_lock);
+	head_value = ioread32(mailbox->head);
+	tail_value = ioread32(mailbox->tail);
+	spin_unlock(&mcu->read_lock);
+
+	return head_value == tail_value;
+}
+EXPORT_SYMBOL_GPL(al5_mcu_is_empty);
+
+void al5_signal_mcu(struct mcu_mailbox_interface *mcu)
+{
+	iowrite32(1, mcu->interrupt_register);
+}
+EXPORT_SYMBOL_GPL(al5_signal_mcu);
+
+const u32 mcu_cache_offset = 0x80000000;
+
+u32 al5_mcu_get_virtual_address(u32 physicalAddress)
+{
+	return physicalAddress + mcu_cache_offset;
+}
+EXPORT_SYMBOL_GPL(al5_mcu_get_virtual_address);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/mcu_utils.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/mcu_utils.c
@@ -0,0 +1,41 @@
+/*
+ * mcu_utils.c memory copy using only 32 bits aligned access
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "mcu_utils.h"
+/* only 32 bits access are available on the apb */
+int memcpy_toio_32(void *pdst, const void *psrc, int size)
+{
+	const __u32 *src = psrc;
+	__u32 *dst = pdst;
+	int i;
+
+	for (i = 0; i < size / 4; ++i)
+		iowrite32(src[i], dst + i);
+	return 0;
+}
+
+int memcpy_fromio_32(void *pdst, void *psrc, int size)
+{
+	__u32 *src = psrc;
+	__u32 *dst = pdst;
+	int i;
+
+	for (i = 0; i < size / 4; ++i)
+		dst[i] = ioread32(src + i);
+	return 0;
+}
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/mcu_utils.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/mcu_utils.h
@@ -0,0 +1,28 @@
+/*
+ * mcu_utils.h memory operation using only 32 bits aligned accesses
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _MCU_UTILS_H_
+#define _MCU_UTILS_H_
+
+#include <linux/types.h>
+#include <linux/io.h>
+
+int memcpy_toio_32(void *pdst, const void *psrc, int size);
+int memcpy_fromio_32(void *pdst, void *psrc, int size);
+
+#endif /* _MCU_UTILS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/xil_clk.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/xil_clk.c
@@ -0,0 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx vcu clock consumer driver
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ *
+ * Author: Rohit Visavalia <rohit.visavalia@xilinx.com>
+ *
+ * This file is used to set the encoder and decoder clk.
+ * it acts as a clk consumer for xilinx VCU.
+ */
+#include <linux/version.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <linux/mfd/syscon/xlnx-vcu.h>
+#include <linux/regmap.h>
+#include <linux/clk.h>
+
+#include "al_codec.h"
+
+#define VCU_PLL_CLK			0x34
+#define VCU_PLL_CLK_DEC			0x64
+#define VCU_MCU_CLK			0x24
+#define VCU_CORE_CLK			0x28
+#define MHZ				1000000
+#define FRAC				100
+
+int xil_clk_set_up(struct platform_device *pdev, struct al5_codec_desc *codec,
+		   const char *core_clk, const char *mcu_clk)
+{
+	u32 refclk, coreclk, mcuclk, inte, deci;
+	int err;
+	struct xvcu_device *xvcu_core = dev_get_drvdata(pdev->dev.parent);
+	codec->logicore_reg_ba = xvcu_core->logicore_reg_ba;
+
+	codec->pll_ref = devm_clk_get(pdev->dev.parent, "pll_ref");
+	if (IS_ERR(codec->pll_ref)) {
+		if (PTR_ERR(codec->pll_ref) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Could not get pll_ref clock\n");
+		return PTR_ERR(codec->pll_ref);
+	}
+
+	codec->core_clk = devm_clk_get(pdev->dev.parent, core_clk);
+	if (IS_ERR(codec->core_clk)) {
+		if (PTR_ERR(codec->core_clk) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Could not get core clock\n");
+		return PTR_ERR(codec->core_clk);
+	}
+
+	codec->mcu_clk = devm_clk_get(pdev->dev.parent, mcu_clk);
+	if (IS_ERR(codec->mcu_clk)) {
+		if (PTR_ERR(codec->mcu_clk) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "Could not get mcu clock\n");
+		return PTR_ERR(codec->mcu_clk);
+	}
+
+	regmap_read(codec->logicore_reg_ba, VCU_PLL_CLK, &inte);
+	regmap_read(codec->logicore_reg_ba, VCU_PLL_CLK_DEC, &deci);
+	regmap_read(codec->logicore_reg_ba, VCU_CORE_CLK, &coreclk);
+	regmap_read(codec->logicore_reg_ba, VCU_MCU_CLK, &mcuclk);
+
+	if (!mcuclk || !coreclk) {
+		dev_err(&pdev->dev, "Invalid mcu and core clock data\n");
+		return -EINVAL;
+	}
+
+	refclk = (inte * MHZ) + (deci * (MHZ / FRAC));
+	coreclk *= MHZ;
+	mcuclk *= MHZ;
+	dev_dbg(&pdev->dev, "Ref clock from logicoreIP is %uHz\n", refclk);
+	dev_dbg(&pdev->dev, "Core clock from logicoreIP is %uHz\n", coreclk);
+	dev_dbg(&pdev->dev, "Mcu clock from logicoreIP is %uHz\n", mcuclk);
+
+	err = clk_set_rate(codec->pll_ref, refclk);
+	if (err)
+		dev_warn(&pdev->dev, "failed to set logicoreIP refclk rate %d\n"
+			 , err);
+
+	err = clk_prepare_enable(codec->pll_ref);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable pll_ref clk source %d\n",
+			err);
+		return err;
+	}
+
+	err = clk_set_rate(codec->mcu_clk, mcuclk);
+	if (err)
+		dev_warn(&pdev->dev, "failed to set logicoreIP mcu clk rate "
+			 "%d\n", err);
+
+	err = clk_prepare_enable(codec->mcu_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable mcu %d\n", err);
+		goto error_mcu;
+	}
+
+	err = clk_set_rate(codec->core_clk, coreclk);
+	if (err)
+		dev_warn(&pdev->dev, "failed to set logicoreIP core clk rate "
+			 "%d\n", err);
+
+	err = clk_prepare_enable(codec->core_clk);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable core %d\n", err);
+		goto error_core;
+	}
+	return 0;
+
+error_core:
+	clk_disable_unprepare(codec->mcu_clk);
+error_mcu:
+	clk_disable_unprepare(codec->pll_ref);
+
+	return err;
+
+}
+EXPORT_SYMBOL_GPL(xil_clk_set_up);
+
+int xil_clk_clean_up(struct platform_device *pdev, struct al5_codec_desc *codec)
+{
+	clk_disable_unprepare(codec->core_clk);
+	devm_clk_put(pdev->dev.parent, codec->core_clk);
+
+	clk_disable_unprepare(codec->mcu_clk);
+	devm_clk_put(pdev->dev.parent, codec->mcu_clk);
+
+	clk_disable_unprepare(codec->pll_ref);
+	devm_clk_put(pdev->dev.parent, codec->pll_ref);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xil_clk_clean_up);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/common/xil_l2_prefetch.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/common/xil_l2_prefetch.c
@@ -0,0 +1,64 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/types.h>
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 10, 0)
+#include <linux/mfd/syscon/xlnx-vcu.h>
+#else
+#include <soc/xilinx/xlnx_vcu.h>
+#endif
+
+#define MEMORY_WORD_SIZE_IN_BITS 32
+
+u32 get_l2_color_bitdepth(void *parent)
+{
+	struct xvcu_device *xvcu = (struct xvcu_device *)parent;
+
+	return xvcu_get_color_depth(xvcu) == 0 ? 8 : 10;
+}
+
+static u32 get_memory_words_in_bits(struct xvcu_device *xvcu)
+{
+	return get_l2_color_bitdepth(xvcu) * MEMORY_WORD_SIZE_IN_BITS;
+}
+
+u32 get_l2_size_in_bits(void *parent)
+{
+	struct xvcu_device *xvcu = (struct xvcu_device *)parent;
+
+	return xvcu_get_memory_depth(xvcu) * get_memory_words_in_bits(xvcu);
+}
+
+u32 get_num_cores(void *parent)
+{
+	struct xvcu_device *xvcu = (struct xvcu_device *)parent;
+
+	u32 num_cores = xvcu_get_num_cores(xvcu);
+
+	if (num_cores == 0)
+		return -1;
+	return num_cores;
+}
+
+u32 get_core_frequency(void *parent)
+{
+	struct xvcu_device *xvcu = (struct xvcu_device *)parent;
+
+	return xvcu_get_clock_frequency(xvcu);
+}
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/device-tree-bindings.txt
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/device-tree-bindings.txt
@@ -0,0 +1,11 @@
+al5e, al5d:
+
+al,mcu_ext_mem_size: specifies the size of the external memory of the mcu. default is MCU_SUBALLOCATOR_SIZE
+
+memory-region: a phandle that points to a reserved-memory node. The driver will use the reserved memory instead of using the CMA pools to allocate its memory. It will also configure the hw ip if needed so that the ip can access the allocated memory. (See https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841683/Linux+Reserved+Memory for more information)
+
+al,devicename: specifies the /dev/X name the created device should have. default is /dev/allegroIP for al5e and /dev/allegroDecodeIP for al5d
+
+al5r:
+
+al,devicename: specifies the /dev/X name the created device should have. default is that the /dev/X node isn't created
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/dmaproxy/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/dmaproxy/Kconfig
@@ -0,0 +1,7 @@
+config DMAPROXY
+        tristate "DMA Proxy client"
+        depends on DMA_ENGINE
+        select DMA_ENGINE_RAID
+        help
+          Simple DMA proxy client. Exports APIs to perform Mem2Mem DMA transfer
+	  To compile this driver as a module, choose M here.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/dmaproxy/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/dmaproxy/Makefile
@@ -0,0 +1 @@
+obj-m += dmaproxy.o
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/dmaproxy/dmaproxy.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/dmaproxy/dmaproxy.c
@@ -0,0 +1,355 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx zynqmp-dma client driver
+ *
+ * Copyright (C) 2019 Xilinx, Inc.
+ *
+ * Author: Jeegar Patel <jeegar.patel@xilinx.com>
+ *
+ * This driver uses the dma engine subsystem's API to perform
+ * memory to memory copy operation using zynqmp-dma and share
+ * IOCTL so userspace application use them
+ */
+
+#include <linux/cdev.h>
+#include <linux/dma-buf.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_dma.h>
+#include <linux/uaccess.h>
+#include <linux/slab.h>
+
+#include "dmaproxy.h"
+
+static dev_t dmaproxy_dev;
+static struct cdev dmaproxy_cdev;
+static struct class *dmaproxy_cl;
+#define MINOR_CNT 8
+
+struct dmacopy_done {
+	bool		done;
+	wait_queue_head_t       wait;
+};
+
+struct dmaproxy_data {
+	struct dma_chan  *chan;
+	struct dma_buf	*src_dbuf;
+	struct dma_buf_attachment  *src_attach;
+	struct sg_table  *src_sgt;
+	struct dma_buf  *dst_dbuf;
+	struct dma_buf_attachment  *dst_attach;
+	struct sg_table  *dst_sgt;
+	dma_addr_t  src_buf;
+	dma_addr_t  dst_buf;
+	struct dmacopy_done	done;
+};
+
+
+static void dmacopy_callback(void *arg)
+{
+	struct dmacopy_done *done = arg;
+
+	done->done = true;
+	wake_up(&done->wait);
+}
+
+static int dmaproxy_open(struct inode *i, struct file *f)
+{
+	struct dmaproxy_data *dmaproxy_data;
+	dma_cap_mask_t mask;
+	struct dma_chan *chan;
+
+	dmaproxy_data = kmalloc(sizeof(*dmaproxy_data), GFP_KERNEL);
+	if (!dmaproxy_data)
+		return -ENOMEM;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_MEMCPY, mask);
+
+	chan = dma_request_channel(mask, NULL, NULL);
+	if (!chan) {
+		pr_err("No more DMA channel available\n");
+		return -EBUSY;
+	}
+
+	dmaproxy_data->chan = chan;
+
+	f->private_data = dmaproxy_data;
+
+	return 0;
+}
+
+static int dmaproxy_close(struct inode *i, struct file *f)
+{
+	struct dmaproxy_data *dmaproxy_data = f->private_data;
+
+	dmaengine_terminate_all(dmaproxy_data->chan);
+	dma_release_channel(dmaproxy_data->chan);
+	dmaproxy_data->chan = NULL;
+
+	kfree(dmaproxy_data);
+	return 0;
+}
+
+static int dmabuf_get_address(struct dmaproxy_data *dmaproxy_data, dmaproxy_arg_t dmaproxy)
+{
+	struct dma_device *dma_dev = dmaproxy_data->chan->device;
+	u8  align = 0;
+
+	dmaproxy_data->src_dbuf = dma_buf_get(dmaproxy.src_fd);
+	if (IS_ERR(dmaproxy_data->src_dbuf)) {
+		pr_err("dma_buf_get failed for src\n");
+		goto fail_src_dbuf;
+	}
+
+	dmaproxy_data->src_attach = dma_buf_attach(dmaproxy_data->src_dbuf, dma_dev->dev);
+	if (IS_ERR(dmaproxy_data->src_attach)) {
+		pr_err("dma_buf_attach get failed for src\n");
+		goto fail_src_attach;
+	}
+
+	dmaproxy_data->src_sgt = dma_buf_map_attachment(dmaproxy_data->src_attach, DMA_BIDIRECTIONAL);
+	if (IS_ERR(dmaproxy_data->src_sgt)) {
+		pr_err("dma_buf_map get failed for src\n");
+		goto fail_src_map;
+	}
+
+	dmaproxy_data->src_buf = sg_dma_address(dmaproxy_data->src_sgt->sgl);
+
+	if (dmaproxy.dst_fd != dmaproxy.src_fd) {
+		dmaproxy_data->dst_dbuf = dma_buf_get(dmaproxy.dst_fd);
+		if (IS_ERR(dmaproxy_data->dst_dbuf)) {
+			pr_err("dma_buf_get failed for dst\n");
+			goto fail_dst_dbuf;
+		}
+
+		dmaproxy_data->dst_attach = dma_buf_attach(dmaproxy_data->dst_dbuf, dma_dev->dev);
+		if (IS_ERR(dmaproxy_data->dst_attach)) {
+			pr_err("dma_buf_attach get failed for dst\n");
+			goto fail_dst_attach;
+		}
+
+		dmaproxy_data->dst_sgt = dma_buf_map_attachment(dmaproxy_data->dst_attach, DMA_BIDIRECTIONAL);
+		if (IS_ERR(dmaproxy_data->dst_sgt)) {
+			pr_err("dma_buf_map get failed for dst\n");
+			goto fail_dst_map;
+		}
+
+		dmaproxy_data->dst_buf = sg_dma_address(dmaproxy_data->dst_sgt->sgl);
+	} else {
+		dmaproxy_data->dst_buf = dmaproxy_data->src_buf;
+	}
+
+	align = dma_dev->copy_align;
+	if (1 << align > dmaproxy.size) {
+		pr_err("%lu-byte buffer too small for %d-byte alignment\n",
+		       dmaproxy.size, 1 << align);
+		goto fail_align;
+	}
+
+	dmaproxy_data->src_buf = dmaproxy_data->src_buf + dmaproxy.src_offset;
+	dmaproxy_data->dst_buf = dmaproxy_data->dst_buf + dmaproxy.dst_offset;
+
+	if (align)
+		dmaproxy_data->src_buf = PTR_ALIGN(dmaproxy_data->src_buf, align);
+	if (align)
+		dmaproxy_data->dst_buf = PTR_ALIGN(dmaproxy_data->dst_buf, align);
+
+	return 0;
+
+fail_align:
+	if (dmaproxy.dst_fd == dmaproxy.src_fd)
+		goto fail_dst_dbuf;
+	else
+		dma_buf_unmap_attachment(dmaproxy_data->dst_attach, dmaproxy_data->dst_sgt, DMA_BIDIRECTIONAL);
+fail_dst_map:
+	dma_buf_detach(dmaproxy_data->dst_dbuf, dmaproxy_data->dst_attach);
+fail_dst_attach:
+	dma_buf_put(dmaproxy_data->dst_dbuf);
+fail_dst_dbuf:
+	dma_buf_unmap_attachment(dmaproxy_data->src_attach, dmaproxy_data->src_sgt, DMA_BIDIRECTIONAL);
+fail_src_map:
+	dma_buf_detach(dmaproxy_data->src_dbuf, dmaproxy_data->src_attach);
+fail_src_attach:
+	dma_buf_put(dmaproxy_data->src_dbuf);
+fail_src_dbuf:
+	return -EINVAL;
+}
+
+static void dmabuf_cleanup(struct dmaproxy_data *dmaproxy_data, dmaproxy_arg_t dmaproxy)
+{
+	dma_buf_unmap_attachment(dmaproxy_data->src_attach, dmaproxy_data->src_sgt, DMA_BIDIRECTIONAL);
+	dma_buf_detach(dmaproxy_data->src_dbuf, dmaproxy_data->src_attach);
+	dma_buf_put(dmaproxy_data->src_dbuf);
+	if (dmaproxy.dst_fd != dmaproxy.src_fd) {
+		dma_buf_unmap_attachment(dmaproxy_data->dst_attach, dmaproxy_data->dst_sgt, DMA_BIDIRECTIONAL);
+		dma_buf_detach(dmaproxy_data->dst_dbuf, dmaproxy_data->dst_attach);
+		dma_buf_put(dmaproxy_data->dst_dbuf);
+	}
+}
+
+static int perform_dma_copy(struct dmaproxy_data *dmaproxy_data, dmaproxy_arg_t dmaproxy)
+{
+	struct dma_device	*dma_dev;
+	struct dma_chan	*chan;
+	struct dma_async_tx_descriptor	*tx = NULL;
+	struct dmaengine_unmap_data	*um = NULL;
+	enum dma_status   status;
+	enum dma_ctrl_flags flags;
+	dma_cookie_t	 cookie;
+	int ret = 0;
+
+	chan = dmaproxy_data->chan;
+	dma_dev = dmaproxy_data->chan->device;
+
+	um = dmaengine_get_unmap_data(dma_dev->dev, 2, GFP_KERNEL);
+	if (!um) {
+		pr_err("dmaengine get unmap data failed\n");
+		return -ENOMEM;
+	}
+	um->len = dmaproxy.size;
+
+	um->addr[0] = dma_map_page(dma_dev->dev, phys_to_page(dmaproxy_data->src_buf),
+				   offset_in_page(dmaproxy_data->src_buf), um->len, DMA_TO_DEVICE);
+	ret = dma_mapping_error(dma_dev->dev, um->addr[0]);
+	if (ret) {
+		pr_err("dma map error for source buffer\n");
+		goto exit;
+	}
+	um->to_cnt++;
+
+	um->addr[1] = dma_map_page(dma_dev->dev, phys_to_page(dmaproxy_data->dst_buf),
+				   offset_in_page(dmaproxy_data->dst_buf), um->len, DMA_BIDIRECTIONAL);
+	ret = dma_mapping_error(dma_dev->dev, um->addr[1]);
+	if (ret) {
+		pr_err("dma map error for destination buffer\n");
+		goto exit;
+	}
+	um->bidi_cnt++;
+
+	flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+	tx = dma_dev->device_prep_dma_memcpy(chan, um->addr[1], um->addr[0], um->len, flags);
+	if (!tx) {
+		pr_err("device prep for dma memcpy get failed\n");
+		ret = -ECANCELED;
+		goto exit;
+	}
+
+	dmaproxy_data->done.done = false;
+	init_waitqueue_head(&dmaproxy_data->done.wait);
+	tx->callback = dmacopy_callback;
+	tx->callback_param = &dmaproxy_data->done;
+	cookie = tx->tx_submit(tx);
+
+	if (dma_submit_error(cookie)) {
+		pr_err("dma submit error\n");
+		ret = -ECANCELED;
+		goto exit;
+	}
+	dma_async_issue_pending(chan);
+
+	/*FIXME: Set some X ms of timeout here */
+	wait_event_timeout(dmaproxy_data->done.wait, dmaproxy_data->done.done,
+			   msecs_to_jiffies(-1));
+
+	status = dma_async_is_tx_complete(chan, cookie, NULL, NULL);
+
+	if (!dmaproxy_data->done.done) {
+		pr_err("timeout error while dma copy\n");
+		ret = -ETIME;
+		goto exit;
+	} else if (status != DMA_COMPLETE) {
+		pr_err("dma copy get failed\n");
+		ret = -ECANCELED;
+		goto exit;
+	}
+
+exit:
+	dmaengine_unmap_put(um);
+	return ret;
+}
+
+static long dmaproxy_ioctl(struct file *f, unsigned int cmd, unsigned long arg)
+{
+	dmaproxy_arg_t	dmaproxy;
+	struct dmaproxy_data	*dmaproxy_data = f->private_data;
+	int	ret;
+
+	switch (cmd) {
+	case DMAPROXY_COPY: {
+		if (copy_from_user(&dmaproxy, (dmaproxy_arg_t *)arg, sizeof(dmaproxy_arg_t))) {
+			pr_err("copy from user failed for DMAPROXY_COPY\n");
+			return -EFAULT;
+		}
+
+		if (dmabuf_get_address(dmaproxy_data, dmaproxy))
+			return -EINVAL;
+
+		ret = perform_dma_copy(dmaproxy_data, dmaproxy);
+
+		dmabuf_cleanup(dmaproxy_data, dmaproxy);
+		break;
+	}
+
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct file_operations dmaproxy_fops = {
+	.owner = THIS_MODULE,
+	.open = dmaproxy_open,
+	.release = dmaproxy_close,
+	.unlocked_ioctl = dmaproxy_ioctl
+};
+
+static int __init dma_proxy_init(void)
+{
+	int ret;
+	struct device *dmaproxy_device;
+
+	ret = alloc_chrdev_region(&dmaproxy_dev, 0, MINOR_CNT, "dmaproxy");
+	if (ret < 0)
+		return ret;
+
+	cdev_init(&dmaproxy_cdev, &dmaproxy_fops);
+	ret = cdev_add(&dmaproxy_cdev, dmaproxy_dev, MINOR_CNT);
+	if (ret < 0) {
+		unregister_chrdev_region(dmaproxy_dev, MINOR_CNT);
+		return ret;
+	}
+
+	dmaproxy_cl = class_create(THIS_MODULE, "char");
+	if (IS_ERR(dmaproxy_cl)) {
+		cdev_del(&dmaproxy_cdev);
+		unregister_chrdev_region(dmaproxy_dev, MINOR_CNT);
+		return PTR_ERR(dmaproxy_cl);
+	}
+
+	dmaproxy_device = device_create(dmaproxy_cl, NULL, dmaproxy_dev, NULL, "dmaproxy");
+	if (IS_ERR(dmaproxy_device)) {
+		class_destroy(dmaproxy_cl);
+		cdev_del(&dmaproxy_cdev);
+		unregister_chrdev_region(dmaproxy_dev, MINOR_CNT);
+		return PTR_ERR(dmaproxy_device);
+	}
+
+	return 0;
+}
+
+static void __exit dma_proxy_exit(void)
+{
+	device_destroy(dmaproxy_cl, dmaproxy_dev);
+	class_destroy(dmaproxy_cl);
+	cdev_del(&dmaproxy_cdev);
+	unregister_chrdev_region(dmaproxy_dev, MINOR_CNT);
+}
+
+module_init(dma_proxy_init)
+module_exit(dma_proxy_exit)
+
+MODULE_AUTHOR("Jeegar Patel <jeegar.patel@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx's zynqmp-dma Client Driver");
+MODULE_LICENSE("GPL v2");
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/dmaproxy/dmaproxy.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/dmaproxy/dmaproxy.h
@@ -0,0 +1,16 @@
+#ifndef DMAPROXY_IOCTL_H
+#define DMAPROXY_IOCTL_H
+#include <linux/ioctl.h>
+
+typedef struct dmaproxy_arg {
+	int src_fd;
+	int dst_fd;
+	int src_offset;
+	int dst_offset;
+	size_t size;
+} dmaproxy_arg_t;
+
+#define DMAPROXY_IOCTL_MAGIC 0x32
+#define DMAPROXY_COPY _IOWR(DMAPROXY_IOCTL_MAGIC, 1, dmaproxy_arg_t *)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_alloc.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_alloc.h
@@ -0,0 +1,35 @@
+/*
+ * al_alloc.h dma buffers allocation and dmabuf support
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_ALLOC_H_
+#define _AL_ALLOC_H_
+
+#include <linux/device.h>
+#include "al_ioctl.h"
+
+struct al5_dma_buffer {
+	size_t size;
+	dma_addr_t dma_handle;
+	void *cpu_handle;
+	size_t offset; /* internal */
+};
+
+struct al5_dma_buffer *al5_alloc_dma(struct device *dev, size_t size);
+void al5_free_dma(struct device *dev, struct al5_dma_buffer *buf);
+
+#endif /* _AL_ALLOC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_alloc_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_alloc_ioctl.h
@@ -0,0 +1,22 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/device.h>
+
+int al5_ioctl_get_dma_fd(struct device *dev, unsigned long arg);
+int al5_ioctl_get_dmabuf_dma_addr(struct device *dev, unsigned long arg);
+
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_buffers_pool.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_buffers_pool.h
@@ -0,0 +1,37 @@
+/*
+ * al_buffers_pool.h high level function to write messages in the mailbox
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __AL_BUFFERS_POOL__
+#define __AL_BUFFERS_POOL__
+
+struct al5_buffers_pool {
+	int count;
+	struct al5_dma_buffer **buffers;
+	void **handles;
+	int *fds;
+};
+
+
+void al5_bufpool_init(struct al5_buffers_pool *bufpool);
+int al5_bufpool_allocate(struct al5_buffers_pool *bufpool,
+			 struct device *device, int count, int size);
+void al5_bufpool_free(struct al5_buffers_pool *bufpool, struct device *device);
+int al5_bufpool_get_id(struct al5_buffers_pool *bufpool, int fd);
+int al5_bufpool_reserve_fd(struct al5_buffers_pool *bufpool, int id);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_char.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_char.h
@@ -0,0 +1,27 @@
+/*
+ * al_char.h char device setup helpers
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef _AL_CHAR_H_
+#define _AL_CHAR_H_
+
+int al5_setup_chrdev_region(int *major, int minor, int nb_devs, char *desc);
+int al5_setup_codec_cdev(struct al5_codec_desc *codec,
+			 const struct file_operations *fops,
+			 struct module *owner, int major, int minor);
+void al5_clean_up_codec_cdev(struct al5_codec_desc *codec);
+
+#endif /* _AL_CHAR_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_codec.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_codec.h
@@ -0,0 +1,101 @@
+/*
+ * al_codec.h per device operation. functions to change the state of the vcu
+ * and functions to handle channels created by the user.
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_CODEC_H_
+#define _AL_CODEC_H_
+
+#include <linux/dma-buf.h>
+#include <linux/cdev.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/firmware.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/poll.h>
+#include <linux/version.h>
+
+#include "al_group.h"
+#include "mcu_interface.h"
+#include "al_alloc.h"
+#include "al_user.h"
+#include "al_vcu.h"
+#include "al_traces.h"
+#include "al_constants.h"
+
+#define al5_writel(val, reg) iowrite32(val, codec->regs + reg)
+#define al5_readl(reg) ioread32(codec->regs + reg)
+
+#define al5_dbg(format, ...) \
+	dev_dbg(codec->device, format, ## __VA_ARGS__)
+
+#define al5_info(format, ...) \
+	dev_info(codec->device, format, ## __VA_ARGS__)
+
+#define al5_err(format, ...) \
+	dev_err(codec->device, format, ## __VA_ARGS__)
+
+#define al5_warn_ratelimited(format, ...) \
+	dev_warn_ratelimited(codec->device, format, ## __VA_ARGS__)
+
+struct al5_codec_desc {
+	struct device *device;
+	struct cdev cdev;
+
+	/* Base addr for regs */
+	void __iomem *regs;
+	unsigned long regs_size;
+
+	/* cache */
+	struct al5_dma_buffer *icache, *suballoc_buf;
+	dma_addr_t dcache_base_addr;
+
+	struct al5_group users_group;
+	int minor;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+	struct clk *pll_ref;
+	struct clk *core_clk;
+	struct clk *mcu_clk;
+	struct regmap *logicore_reg_ba;
+#endif
+};
+
+struct al5_filp_data {
+	struct al5_codec_desc *codec;
+	struct al5_user *user;
+};
+
+int al5_codec_set_up(struct al5_codec_desc *codec,
+		     struct platform_device *pdev,
+		     size_t max_users_nb);
+
+void al5_codec_tear_down(struct al5_codec_desc *codec);
+
+int al5_codec_set_firmware(struct al5_codec_desc *codec, char *fw_file,
+			   char *bl_fw_file);
+
+int al5_codec_open(struct inode *inode, struct file *filp);
+int al5_codec_release(struct inode *inode, struct file *filp);
+
+long al5_codec_compat_ioctl(struct file *file, unsigned int cmd,
+			    unsigned long arg);
+
+unsigned int al5_codec_poll(struct file *filp, poll_table *wait);
+
+#endif /* _AL_CODEC_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_codec_mails.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_codec_mails.h
@@ -0,0 +1,84 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef __AL_CODEC_MAILS__
+#define __AL_CODEC_MAILS__
+
+#include "al_mail.h"
+
+enum al5_mail_uid {
+	AL_MCU_MSG_INIT,
+	AL_MCU_MSG_DEINIT,
+	AL_MCU_MSG_IP_INT,
+	AL_MCU_MSG_CPU_INT,
+	AL_MCU_MSG_CPU_RSP,
+	AL_MCU_MSG_CREATE_CHANNEL,
+	AL_MCU_MSG_DESTROY_CHANNEL,
+	AL_MCU_MSG_ENCODE_ONE_FRM,
+	AL_MCU_MSG_DECODE_ONE_FRM,
+	AL_MCU_MSG_SEARCH_START_CODE,
+	AL_MCU_MSG_QUIET_DESTROY_CHANNEL,
+	AL_MCU_MSG_GET_RESOURCE,
+	AL_MCU_MSG_SET_BUFFER,
+	AL_MCU_MSG_SHUTDOWN,
+	AL_MCU_MSG_PUSH_BUFFER_INTERMEDIATE,
+	AL_MCU_MSG_PUSH_BUFFER_REFERENCE,
+
+	AL_MCU_MSG_GET_RECONSTRUCTED_PICTURE,
+	AL_MCU_MSG_RELEASE_RECONSTRUCTED_PICTURE,
+	AL_MCU_MSG_PUT_STREAM_BUFFER,
+
+	/* NSFProd */
+	AL_MCU_MSG_TRACE,
+	AL_MCU_MSG_RANDOM_TEST,
+	AL_MCU_MSG_SET_TIMER_BUFFER,
+	AL_MCU_MSG_SET_IRQ_TIMER_BUFFER,
+
+	AL_MCU_MSG_DECODE_ONE_SLICE,
+
+	/* sentinel */
+	AL_MCU_MSG_MAX,
+};
+
+struct mcu_init_msg {
+	u32 addr;
+	u32 size;
+	u32 l2_size_in_bits;
+	u32 l2_color_bitdepth;
+	u32 num_cores;
+	u32 core_frequency;
+	u32 plugin_enabled;
+};
+
+struct msg_info {
+	u32 chan_uid;
+	void *priv;
+};
+
+struct al5_mail *create_init_msg(u32 chan_uid, struct mcu_init_msg *msg);
+struct al5_mail *create_destroy_channel_msg(u32 chan_uid);
+struct al5_mail *create_quiet_destroy_channel_msg(u32 chan_uid);
+
+struct al5_mail *al5_create_classic_mail(u32 sender_uid, u32 msg_uid, void *msg,
+					 u32 msg_size);
+struct al5_mail *al5_create_empty_mail(u32 sender_uid, u32 msg_uid);
+
+u32 al5_mail_get_chan_uid(struct al5_mail *mail);
+
+void al5_print_mcu_trace(struct al5_mail *mail);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_constants.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_constants.h
@@ -0,0 +1,37 @@
+#ifndef _AL_CONSTANTS_H_
+#define ifndef _AL_CONSTANTS_H_
+
+/* MCU Mailbox */
+#define MAILBOX_CMD                     0x7000
+#define MAILBOX_STATUS                  0x7800
+#define MAILBOX_SIZE                    (0x800 - 0x8)
+
+/* MCU Bootloader */
+#define AL5_MCU_INTERRUPT_HANDLER       0x0010
+#define MCU_SLEEP_INSTRUCTION           0xba020004 /* Instruction "mbar 16" */
+
+/* MCU Control Regs */
+#define AL5_MCU_RESET                   0x9000
+#define AL5_MCU_RESET_MODE              0x9004
+#define AL5_MCU_STA                     0x9008
+#define AL5_MCU_WAKEUP                  0x900c
+
+#define AL5_ICACHE_ADDR_OFFSET_MSB      0x9010
+#define AL5_ICACHE_ADDR_OFFSET_LSB      0x9014
+#define AL5_DCACHE_ADDR_OFFSET_MSB      0x9018
+#define AL5_DCACHE_ADDR_OFFSET_LSB      0x901c
+
+#define AL5_MCU_INTERRUPT               0x9100
+#define AL5_MCU_INTERRUPT_MASK          0x9104
+#define AL5_MCU_INTERRUPT_CLR           0x9108
+
+#define AXI_ADDR_OFFSET_IP              0x9208
+
+/* MCU Cache */
+#define MCU_SUBALLOCATOR_SIZE           (1024 * 1024 * 32)      /* 32 MB */
+#define MCU_CACHE_OFFSET                0x80000000
+#define AL5_ICACHE_SIZE                 (1024 * 600)            /* 600 KB (for possible extensions) */
+#define AL5_RC_PLUGIN_CODE_START        (1024 * 512)
+#define MCU_SRAM_SIZE                   0x8000                  /* 32 kB */
+
+#endif /* _AL_CONSTANTS_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_dmabuf.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_dmabuf.h
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#include <linux/device.h>
+#include "al_alloc.h"
+
+struct al5_buffer_info {
+	u32 bus_address;
+	u32 size;
+};
+
+void *al5_dmabuf_wrap(struct device *dev, size_t size,
+		      struct al5_dma_buffer *buffer);
+int al5_create_dmabuf_fd(struct device *dev, size_t size,
+			 struct al5_dma_buffer *buffer);
+
+int al5_allocate_dmabuf(struct device *dev, size_t size, u32 *fd);
+int al5_dmabuf_get_address(struct device *dev, u32 fd, u32 *bus_address);
+int al5_get_dmabuf_info(struct device *dev, u32 fd,
+			struct al5_buffer_info *info);
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_group.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_group.h
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef __AL_GROUP__
+#define __AL_GROUP__
+
+#include <linux/spinlock.h>
+
+#include "mcu_interface.h"
+#include "al_user.h"
+
+struct al5_group {
+	struct mcu_mailbox_interface *mcu;
+	spinlock_t lock;
+
+	int max_users_nb;
+	struct al5_user **users;
+	struct device *device;
+};
+
+void al5_group_init(struct al5_group *group, struct mcu_mailbox_interface *mcu,
+		    int max_users_nb, struct device *device);
+void al5_group_deinit(struct al5_group *group);
+
+int al5_group_bind_user(struct al5_group *group, struct al5_user *user);
+void al5_group_unbind_user(struct al5_group *group, struct al5_user *user);
+
+struct al5_user *al5_group_user_from_uid(struct al5_group *group, int user_uid);
+struct al5_user *al5_group_user_from_chan_uid(struct al5_group *group,
+					      int chan_uid);
+
+void al5_group_read_mails(struct al5_group *group);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_ioctl.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_ioctl.h
@@ -0,0 +1,33 @@
+/*
+ * al_ioctl.h common ioctl. allocation ioctl
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_IOCTL_H_
+#define _AL_IOCTL_H_
+
+#define GET_DMA_FD        _IOWR('q', 13, struct al5_dma_info)
+#define GET_DMA_PHY       _IOWR('q', 18, struct al5_dma_info)
+
+#include <linux/types.h>
+
+struct al5_dma_info {
+	__u32 fd;
+	__u32 size;
+	__u32 phy_addr;
+};
+
+#endif /* _AL_IOCTL_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_list.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_list.h
@@ -0,0 +1,35 @@
+/*
+ * al_list.h
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __AL_LIST__
+#define __AL_LIST__
+
+#include "al_mailbox.h"
+
+struct al5_list {
+	struct al5_mail *mail;
+	struct al5_list *next;
+};
+
+void al5_list_init(struct al5_list **l);
+int al5_list_empty(const struct al5_list *l);
+int al5_list_push(struct al5_list **l, struct al5_mail *mail);
+struct al5_mail *al5_list_pop(struct al5_list **l);
+void al5_list_empty_and_destroy(struct al5_list **l);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_mail.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_mail.h
@@ -0,0 +1,38 @@
+/*
+ * al_mail.h create a message to send to the vcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef _MCU_COMMON_H_
+#define _MCU_COMMON_H_
+
+#include <linux/types.h>
+
+struct al5_mail;
+
+struct al5_mail *al5_mail_create(u32 msg_uid, u32 size);
+void al5_mail_write(struct al5_mail *mail, void *content, u32 size);
+void al5_mail_write_word(struct al5_mail *mail, u32 word);
+void al5_free_mail(struct al5_mail *m_data);
+u32 al5_mail_get_uid(struct al5_mail *mail);
+u32 al5_mail_get_size(struct al5_mail *mail);
+void *al5_mail_get_body(struct al5_mail *mail);
+u32 al5_mail_get_word(struct al5_mail *mail, u32 word_offset);
+
+struct al5_mail *al5_mail_create_copy(struct al5_mail *mail);
+
+#endif /* _MCU_COMMON_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_mail_private.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_mail_private.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef __AL_MAIL_PRIVATE__
+#define __AL_MAIL_PRIVATE__
+
+struct al5_mail {
+	u32 body_offset;
+	u16 msg_uid;
+	u16 body_size;
+	u8 *body;
+};
+
+size_t al5_get_mail_alloc_size(u32 content_size);
+void al5_mail_init(struct al5_mail *mail, u32 msg_uid, u32 content_size);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_mailbox.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_mailbox.h
@@ -0,0 +1,38 @@
+/*
+ * al_mailbox.h mailbox mechanisms. r/w messages to/from the mcu
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _MCU_MAILBOX_H_
+#define _MCU_MAILBOX_H_
+
+#include <linux/types.h>
+
+#include "al_mail.h"
+
+struct mailbox {
+	size_t size; /* In bytes */
+	u8 *data;
+	void *tail;
+	void *head;
+	u16 local_tail;
+};
+
+void al5_mailbox_init(struct mailbox *box, void *base, size_t data_size);
+int al5_mailbox_write(struct mailbox *box, struct al5_mail *mail);
+bool al5_mailbox_read(struct mailbox *box, struct al5_mail *mail, size_t mail_size);
+
+#endif /* _MCU_MAILBOX_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_queue.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_queue.h
@@ -0,0 +1,46 @@
+/*
+ * al_queue.h
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __AL_QUEUE__
+#define __AL_QUEUE__
+
+#include <linux/sched.h>
+#include <linux/wait.h>
+#include <linux/spinlock.h>
+
+#include "al_mailbox.h"
+#include "al_list.h"
+
+#define WAIT_TIMEOUT_DURATION (HZ * 5)
+
+struct al5_queue {
+	wait_queue_head_t queue;
+	struct al5_list *list;
+	spinlock_t lock;
+	int locked;
+};
+
+void al5_queue_init(struct al5_queue *q);
+struct al5_mail *al5_queue_pop_no_wait(struct al5_queue *q);
+struct al5_mail *al5_queue_pop(struct al5_queue *q);
+int al5_queue_pop_timeout(struct al5_mail **mail, struct al5_queue *q);
+int al5_queue_push(struct al5_queue *q, struct al5_mail *mail);
+void al5_queue_unlock(struct al5_queue *q);
+void al5_queue_lock(struct al5_queue *q);
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_traces.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_traces.h
@@ -0,0 +1,64 @@
+/*
+ * al_traces.h
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_TRACES_H_
+#define _AL_TRACES_H_
+
+#include <linux/printk.h>
+
+#define AL5_DEBUG 0
+#if AL5_DEBUG
+#define mails_info(format, ...) \
+	do {    \
+		pr_info("\e[0;32m"); \
+		pr_cont(format, ## __VA_ARGS__); \
+		pr_cont("\e[0m\n"); \
+	} while (0)
+#define ioctl_info(format, ...) \
+	do {    \
+		pr_info("\e[0;33m"); \
+		pr_cont(format, ## __VA_ARGS__); \
+		pr_cont("\e[0m\n"); \
+	} while (0)
+
+#define irq_info(format, ...) \
+	do { \
+		pr_info("\e[0;34m"); \
+		pr_cont(format, ## __VA_ARGS__); \
+		pr_cont("\e[0m\n"); \
+	} while (0)
+
+#define setup_info(format, ...) \
+	dev_info(codec->device, format, ## __VA_ARGS__)
+#else
+
+#define mails_info(format, ...)
+#define ioctl_info(format, ...)
+#define irq_info(format, ...)
+#define setup_info(format, ...)
+
+#endif
+
+#define mcu_info(format, ...) \
+	do {    \
+		pr_info("\e[0;31m"); \
+		pr_cont(format, ## __VA_ARGS__); \
+		pr_cont("\e[0m\n"); \
+	} while (0)
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_user.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_user.h
@@ -0,0 +1,112 @@
+/*
+ * al_user.h high level function to write messages in the mailbox
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_USER_H_
+#define _AL_USER_H_
+
+#include <linux/mutex.h>
+#include <linux/device.h>
+
+#include "al_ioctl.h"
+#include "al_mail.h"
+#include "al_queue.h"
+#include "mcu_interface.h"
+#include "al_buffers_pool.h"
+
+enum user_mail {
+	AL5_USER_MAIL_INIT,
+	AL5_USER_MAIL_CREATE,
+	AL5_USER_MAIL_DESTROY,
+	AL5_USER_MAIL_STATUS,
+	AL5_USER_MAIL_SC,
+	AL5_USER_MAIL_DEBUG,
+	AL5_USER_MAIL_REC,
+
+	/* always the last one */
+	AL5_USER_MAIL_NUMBER,
+};
+
+enum user_operations {
+	AL5_USER_INIT,
+	AL5_USER_CHANNEL,
+	AL5_USER_STATUS,
+	AL5_USER_SC,
+
+	/* always the last one */
+	AL5_USER_OPS_NUMBER
+};
+
+#define NO_CHECKPOINT -1
+#define CHECKPOINT_ALLOCATE_BUFFERS 1
+#define CHECKPOINT_SEND_INTERMEDIATE_BUFFERS 2
+#define CHECKPOINT_SEND_REFERENCE_BUFFERS 3
+#define CHECKPOINT_CREATED 4
+#define CHECKPOINT_DESTROYED 5
+#define BAD_CHAN 0xff
+
+/* User structure
+ * There is one User for each opening of the device file descriptor.
+ * Being a user allow us to call ioctl's to communicate with mcu or ip
+ * In order to perform encoding or decoding operations,
+ * creating a channel is needed
+ */
+
+struct al5_user {
+	/* the user id is used to identify the mail that are exchanged between the user
+	   and the mcu before the creation of a channel */
+	int uid;
+	/* The chan_uid is used to identify the channel that should receive the mails
+	   in the mcu and in the driver. In the driver it is used to select which user
+	   should receive the current mail. */
+	int chan_uid;
+
+	int checkpoint;
+
+	struct mcu_mailbox_interface *mcu;
+
+	struct al5_queue queues[AL5_USER_MAIL_NUMBER];
+	struct mutex locks[AL5_USER_OPS_NUMBER];
+
+	struct device *device;
+	struct al5_buffers_pool int_buffers;
+	struct al5_buffers_pool rec_buffers;
+
+	bool non_block;
+};
+
+void al5_user_init(struct al5_user *user, int uid,
+		   struct mcu_mailbox_interface *mcu, struct device *device);
+int al5_user_destroy_channel(struct al5_user *user, int quiet);
+void al5_user_remove_residual_messages(struct al5_user *user);
+
+int al5_check_and_send(struct al5_user *user, struct al5_mail *mail);
+
+int al5_chan_is_created(struct al5_user *user);
+
+int al5_have_checkpoint(struct al5_user *user);
+
+int al5_user_deliver(struct al5_user *user, struct al5_mail *mail);
+
+int al5_is_ready(struct al5_user *user, struct al5_mail **mail, int my_uid);
+
+int al5_status_is_ready(struct al5_user *user, struct al5_mail **mail,
+			int my_uid);
+
+struct al5_mail *al5_user_get_mail(struct al5_user *user, u32 mail_uid);
+
+#endif /* _AL_USER_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/al_vcu.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/al_vcu.h
@@ -0,0 +1,33 @@
+/*
+ * al_vcu.h handle communication with mcu via interrupts
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _AL_VCU_H_
+#define _AL_VCU_H_
+
+#include <linux/interrupt.h>
+
+#define AL5_NR_DEVS 4
+#define MAX_USERS_NB 256
+
+extern int max_users_nb;
+
+irqreturn_t al5_irq_handler(int irq, void *data);
+irqreturn_t al5_hardirq_handler(int irq, void *data);
+
+
+#endif /* _AL_VCU_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/mcu_interface.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/mcu_interface.h
@@ -0,0 +1,55 @@
+/*
+ * mcu_interface.h mcu interface of the vcu. implements access control to the
+ * mailbox and the protocol to signal a message was sent to the mcu.
+ *
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _MCU_INTERFACE_H_
+#define _MCU_INTERFACE_H_
+
+#include <linux/slab.h>
+#include <linux/device.h>
+
+#include "al_mailbox.h"
+#include "al_mail.h"
+
+struct mcu_mailbox_interface;
+
+struct mcu_mailbox_config {
+	unsigned long cmd_base;
+	unsigned long status_base;
+	unsigned long cmd_size;
+	unsigned long status_size;
+};
+
+int al5_mcu_interface_create(struct mcu_mailbox_interface **mcu,
+			     struct device *device,
+			     struct mcu_mailbox_config *config,
+			     void *mcu_interrupt_register);
+
+void al5_mcu_interface_destroy(struct mcu_mailbox_interface *mcu,
+			       struct device *device);
+
+int al5_mcu_is_empty(struct mcu_mailbox_interface *mcu);
+
+int al5_mcu_send(struct mcu_mailbox_interface *mcu, struct al5_mail *data);
+struct al5_mail *al5_mcu_recv(struct mcu_mailbox_interface *mcu);
+
+void al5_signal_mcu(struct mcu_mailbox_interface *mcu);
+
+u32 al5_mcu_get_virtual_address(u32 physicalAddress);
+
+#endif /* _MCU_INTERFACE_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/mcu_interface_private.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/mcu_interface_private.h
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2019, Allegro DVT (www.allegrodvt.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifndef __MCU_INTERFACE_PRIVATE__
+#define __MCU_INTERFACE_PRIVATE__
+
+#include <linux/spinlock.h>
+#include "mcu_interface.h"
+
+struct mcu_mailbox_interface {
+	struct mailbox mcu_to_cpu;
+	struct mailbox cpu_to_mcu;
+	spinlock_t read_lock;
+	spinlock_t write_lock;
+	void *interrupt_register;
+	struct device *dev;
+};
+
+#endif
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/staging/xilinx-vcu/include/xil_clk.h
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/staging/xilinx-vcu/include/xil_clk.h
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx vcu clock consumer driver header file
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ *
+ * Author: Rohit Visavalia <rohit.visavalia@xilinx.com>
+ *
+ * This file is used to set the encoder and decoder clk.
+ * it acts as a clk consumer for xilinx VCU.
+ */
+#ifndef _XIL_CLK_H_
+#define _XIL_CLK_H_
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(5, 15, 0)
+#include "al_codec.h"
+
+int xil_clk_set_up(struct platform_device *pdev, struct al5_codec_desc *codec,
+		   const char *core_clk, const char *mcu_clk);
+int xil_clk_clean_up(struct platform_device *pdev,
+		     struct al5_codec_desc *codec);
+
+#endif
+#endif /* _XIL_CLK_H_ */
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/ubuntu-host/Kconfig
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/ubuntu-host/Kconfig
@@ -0,0 +1,5 @@
+config UBUNTU_HOST
+	tristate "proc dir for exporting host data to containers"
+	help
+	  Creates an ubuntu-host directory in proc for providing data from
+	  Ubuntu hosts to containers.
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/ubuntu-host/Makefile
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/ubuntu-host/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_UBUNTU_HOST) += ubuntu-host.o
--- linux-xilinx-zynqmp-5.15.0.orig/ubuntu/ubuntu-host/ubuntu-host.c
+++ linux-xilinx-zynqmp-5.15.0/ubuntu/ubuntu-host/ubuntu-host.c
@@ -0,0 +1,68 @@
+#include <linux/uaccess.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/proc_fs.h>
+#include <asm/uaccess.h>
+
+#define PROC_DIR		"ubuntu-host"
+
+#define ESM_TOKEN_FILE		"esm-token"
+#define ESM_TOKEN_MAX_SIZE		64
+
+static struct proc_dir_entry *proc_dir;
+static char esm_token_buffer[ESM_TOKEN_MAX_SIZE];
+
+static ssize_t esm_token_read(struct file *f, char __user *buf, size_t len,
+			      loff_t *off)
+{
+	return simple_read_from_buffer(buf, len, off, esm_token_buffer,
+				       strlen(esm_token_buffer));
+}
+
+static ssize_t esm_token_write(struct file *f, const char __user *buf,
+			       size_t len, loff_t *off)
+{
+	ssize_t ret;
+
+	if (len >= ESM_TOKEN_MAX_SIZE - 1)
+		return -EINVAL;
+
+	ret = simple_write_to_buffer(esm_token_buffer, ESM_TOKEN_MAX_SIZE - 1,
+				     off, buf, len);
+	if (ret >= 0)
+		esm_token_buffer[ret] = '\0';
+
+	return ret;
+}
+
+static const struct proc_ops esm_token_fops = {
+	.proc_read = esm_token_read,
+	.proc_write = esm_token_write,
+};
+
+static void ubuntu_host_cleanup(void)
+{
+	remove_proc_entry(ESM_TOKEN_FILE, proc_dir);
+	proc_remove(proc_dir);
+}
+
+static int __init ubuntu_host_init(void)
+{
+	proc_dir = proc_mkdir(PROC_DIR, NULL);
+	if (!proc_dir) {
+		pr_err("Failed to create ubuntu-host dir\n");
+		return -ENOMEM;
+	}
+
+	if (!proc_create_data(ESM_TOKEN_FILE, 0644, proc_dir, &esm_token_fops, NULL)) {
+		pr_err("Failed to create esm-tokan file\n");
+		ubuntu_host_cleanup();
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+module_init(ubuntu_host_init);
+module_exit(ubuntu_host_cleanup);
+MODULE_LICENSE("GPL");
--- linux-xilinx-zynqmp-5.15.0.orig/usr/include/Makefile
+++ linux-xilinx-zynqmp-5.15.0/usr/include/Makefile
@@ -28,13 +28,13 @@
 no-header-test += linux/android/binder.h
 no-header-test += linux/android/binderfs.h
 no-header-test += linux/coda.h
+no-header-test += linux/cyclades.h
 no-header-test += linux/errqueue.h
 no-header-test += linux/fsmap.h
 no-header-test += linux/hdlc/ioctl.h
 no-header-test += linux/ivtv.h
 no-header-test += linux/kexec.h
 no-header-test += linux/matroxfb.h
-no-header-test += linux/nfc.h
 no-header-test += linux/omap3isp.h
 no-header-test += linux/omapfb.h
 no-header-test += linux/patchkey.h
@@ -48,6 +48,9 @@
 no-header-test += linux/v4l2-subdev.h
 no-header-test += linux/videodev2.h
 no-header-test += linux/vm_sockets.h
+no-header-test += linux/xilinx-sdirxss.h
+no-header-test += linux/xilinx-hls.h
+no-header-test += linux/xilinx-v4l2-events.h
 no-header-test += sound/asequencer.h
 no-header-test += sound/asoc.h
 no-header-test += sound/asound.h
--- linux-xilinx-zynqmp-5.15.0.orig/virt/kvm/async_pf.c
+++ linux-xilinx-zynqmp-5.15.0/virt/kvm/async_pf.c
@@ -88,7 +88,27 @@
 	rcuwait_wake_up(&vcpu->wait);
 
 	mmput(mm);
-	kvm_put_kvm(vcpu->kvm);
+}
+
+static void kvm_flush_and_free_async_pf_work(struct kvm_async_pf *work)
+{
+	/*
+	 * The async #PF is "done", but KVM must wait for the work item itself,
+	 * i.e. async_pf_execute(), to run to completion.  If KVM is a module,
+	 * KVM must ensure *no* code owned by the KVM (the module) can be run
+	 * after the last call to module_put().  Note, flushing the work item
+	 * is always required when the item is taken off the completion queue.
+	 * E.g. even if the vCPU handles the item in the "normal" path, the VM
+	 * could be terminated before async_pf_execute() completes.
+	 *
+	 * Wake all events skip the queue and go straight done, i.e. don't
+	 * need to be flushed (but sanity check that the work wasn't queued).
+	 */
+	if (work->wakeup_all)
+		WARN_ON_ONCE(work->work.func);
+	else
+		flush_work(&work->work);
+	kmem_cache_free(async_pf_cache, work);
 }
 
 void kvm_clear_async_pf_completion_queue(struct kvm_vcpu *vcpu)
@@ -115,7 +135,6 @@
 #else
 		if (cancel_work_sync(&work->work)) {
 			mmput(work->mm);
-			kvm_put_kvm(vcpu->kvm); /* == work->vcpu->kvm */
 			kmem_cache_free(async_pf_cache, work);
 		}
 #endif
@@ -127,7 +146,10 @@
 			list_first_entry(&vcpu->async_pf.done,
 					 typeof(*work), link);
 		list_del(&work->link);
-		kmem_cache_free(async_pf_cache, work);
+
+		spin_unlock(&vcpu->async_pf.lock);
+		kvm_flush_and_free_async_pf_work(work);
+		spin_lock(&vcpu->async_pf.lock);
 	}
 	spin_unlock(&vcpu->async_pf.lock);
 
@@ -152,7 +174,7 @@
 
 		list_del(&work->queue);
 		vcpu->async_pf.queued--;
-		kmem_cache_free(async_pf_cache, work);
+		kvm_flush_and_free_async_pf_work(work);
 	}
 }
 
@@ -187,7 +209,6 @@
 	work->arch = *arch;
 	work->mm = current->mm;
 	mmget(work->mm);
-	kvm_get_kvm(work->vcpu->kvm);
 
 	INIT_WORK(&work->work, async_pf_execute);
 
--- linux-xilinx-zynqmp-5.15.0.orig/virt/kvm/coalesced_mmio.c
+++ linux-xilinx-zynqmp-5.15.0/virt/kvm/coalesced_mmio.c
@@ -187,15 +187,17 @@
 			r = kvm_io_bus_unregister_dev(kvm,
 				zone->pio ? KVM_PIO_BUS : KVM_MMIO_BUS, &dev->dev);
 
+			kvm_iodevice_destructor(&dev->dev);
+
 			/*
 			 * On failure, unregister destroys all devices on the
 			 * bus _except_ the target device, i.e. coalesced_zones
-			 * has been modified.  No need to restart the walk as
-			 * there aren't any zones left.
+			 * has been modified.  Bail after destroying the target
+			 * device, there's no need to restart the walk as there
+			 * aren't any zones left.
 			 */
 			if (r)
 				break;
-			kvm_iodevice_destructor(&dev->dev);
 		}
 	}
 
--- linux-xilinx-zynqmp-5.15.0.orig/virt/kvm/eventfd.c
+++ linux-xilinx-zynqmp-5.15.0/virt/kvm/eventfd.c
@@ -456,8 +456,8 @@
 	idx = srcu_read_lock(&kvm->irq_srcu);
 	gsi = kvm_irq_map_chip_pin(kvm, irqchip, pin);
 	if (gsi != -1)
-		hlist_for_each_entry_rcu(kian, &kvm->irq_ack_notifier_list,
-					 link)
+		hlist_for_each_entry_srcu(kian, &kvm->irq_ack_notifier_list,
+					  link, srcu_read_lock_held(&kvm->irq_srcu))
 			if (kian->gsi == gsi) {
 				srcu_read_unlock(&kvm->irq_srcu, idx);
 				return true;
@@ -473,8 +473,8 @@
 {
 	struct kvm_irq_ack_notifier *kian;
 
-	hlist_for_each_entry_rcu(kian, &kvm->irq_ack_notifier_list,
-				 link)
+	hlist_for_each_entry_srcu(kian, &kvm->irq_ack_notifier_list,
+				  link, srcu_read_lock_held(&kvm->irq_srcu))
 		if (kian->gsi == gsi)
 			kian->irq_acked(kian);
 }
--- linux-xilinx-zynqmp-5.15.0.orig/virt/kvm/kvm_main.c
+++ linux-xilinx-zynqmp-5.15.0/virt/kvm/kvm_main.c
@@ -117,6 +117,8 @@
 
 static const struct file_operations stat_fops_per_vm;
 
+static struct file_operations kvm_chardev_ops;
+
 static long kvm_vcpu_ioctl(struct file *file, unsigned int ioctl,
 			   unsigned long arg);
 #ifdef CONFIG_KVM_COMPAT
@@ -155,11 +157,17 @@
 static unsigned long long kvm_createvm_count;
 static unsigned long long kvm_active_vms;
 
+static DEFINE_PER_CPU(cpumask_var_t, cpu_kick_mask);
+
 __weak void kvm_arch_mmu_notifier_invalidate_range(struct kvm *kvm,
 						   unsigned long start, unsigned long end)
 {
 }
 
+__weak void kvm_arch_guest_memory_reclaimed(struct kvm *kvm)
+{
+}
+
 bool kvm_is_zone_device_pfn(kvm_pfn_t pfn)
 {
 	/*
@@ -251,50 +259,57 @@
 	return true;
 }
 
+static void kvm_make_vcpu_request(struct kvm *kvm, struct kvm_vcpu *vcpu,
+				  unsigned int req, cpumask_var_t tmp,
+				  int current_cpu)
+{
+	int cpu;
+
+	kvm_make_request(req, vcpu);
+
+	if (!(req & KVM_REQUEST_NO_WAKEUP) && kvm_vcpu_wake_up(vcpu))
+		return;
+
+	/*
+	 * tmp can be "unavailable" if cpumasks are allocated off stack as
+	 * allocation of the mask is deliberately not fatal and is handled by
+	 * falling back to kicking all online CPUs.
+	 */
+	if (!cpumask_available(tmp))
+		return;
+
+	/*
+	 * Note, the vCPU could get migrated to a different pCPU at any point
+	 * after kvm_request_needs_ipi(), which could result in sending an IPI
+	 * to the previous pCPU.  But, that's OK because the purpose of the IPI
+	 * is to ensure the vCPU returns to OUTSIDE_GUEST_MODE, which is
+	 * satisfied if the vCPU migrates. Entering READING_SHADOW_PAGE_TABLES
+	 * after this point is also OK, as the requirement is only that KVM wait
+	 * for vCPUs that were reading SPTEs _before_ any changes were
+	 * finalized. See kvm_vcpu_kick() for more details on handling requests.
+	 */
+	if (kvm_request_needs_ipi(vcpu, req)) {
+		cpu = READ_ONCE(vcpu->cpu);
+		if (cpu != -1 && cpu != current_cpu)
+			__cpumask_set_cpu(cpu, tmp);
+	}
+}
+
 bool kvm_make_vcpus_request_mask(struct kvm *kvm, unsigned int req,
 				 struct kvm_vcpu *except,
 				 unsigned long *vcpu_bitmap, cpumask_var_t tmp)
 {
-	int i, cpu, me;
 	struct kvm_vcpu *vcpu;
+	int i, me;
 	bool called;
 
 	me = get_cpu();
 
-	kvm_for_each_vcpu(i, vcpu, kvm) {
-		if ((vcpu_bitmap && !test_bit(i, vcpu_bitmap)) ||
-		    vcpu == except)
-			continue;
-
-		kvm_make_request(req, vcpu);
-
-		if (!(req & KVM_REQUEST_NO_WAKEUP) && kvm_vcpu_wake_up(vcpu))
-			continue;
-
-		/*
-		 * tmp can be "unavailable" if cpumasks are allocated off stack
-		 * as allocation of the mask is deliberately not fatal and is
-		 * handled by falling back to kicking all online CPUs.
-		 */
-		if (!cpumask_available(tmp))
+	for_each_set_bit(i, vcpu_bitmap, KVM_MAX_VCPUS) {
+		vcpu = kvm_get_vcpu(kvm, i);
+		if (!vcpu || vcpu == except)
 			continue;
-
-		/*
-		 * Note, the vCPU could get migrated to a different pCPU at any
-		 * point after kvm_request_needs_ipi(), which could result in
-		 * sending an IPI to the previous pCPU.  But, that's ok because
-		 * the purpose of the IPI is to ensure the vCPU returns to
-		 * OUTSIDE_GUEST_MODE, which is satisfied if the vCPU migrates.
-		 * Entering READING_SHADOW_PAGE_TABLES after this point is also
-		 * ok, as the requirement is only that KVM wait for vCPUs that
-		 * were reading SPTEs _before_ any changes were finalized.  See
-		 * kvm_vcpu_kick() for more details on handling requests.
-		 */
-		if (kvm_request_needs_ipi(vcpu, req)) {
-			cpu = READ_ONCE(vcpu->cpu);
-			if (cpu != -1 && cpu != me)
-				__cpumask_set_cpu(cpu, tmp);
-		}
+		kvm_make_vcpu_request(kvm, vcpu, req, tmp, me);
 	}
 
 	called = kvm_kick_many_cpus(tmp, !!(req & KVM_REQUEST_WAIT));
@@ -306,14 +321,25 @@
 bool kvm_make_all_cpus_request_except(struct kvm *kvm, unsigned int req,
 				      struct kvm_vcpu *except)
 {
-	cpumask_var_t cpus;
+	struct kvm_vcpu *vcpu;
+	struct cpumask *cpus;
 	bool called;
+	int i, me;
 
-	zalloc_cpumask_var(&cpus, GFP_ATOMIC);
+	me = get_cpu();
 
-	called = kvm_make_vcpus_request_mask(kvm, req, except, NULL, cpus);
+	cpus = this_cpu_cpumask_var_ptr(cpu_kick_mask);
+	cpumask_clear(cpus);
+
+	kvm_for_each_vcpu(i, vcpu, kvm) {
+		if (vcpu == except)
+			continue;
+		kvm_make_vcpu_request(kvm, vcpu, req, cpus, me);
+	}
+
+	called = kvm_kick_many_cpus(cpus, !!(req & KVM_REQUEST_WAIT));
+	put_cpu();
 
-	free_cpumask_var(cpus);
 	return called;
 }
 
@@ -351,6 +377,12 @@
 	kvm_make_all_cpus_request(kvm, KVM_REQ_MMU_RELOAD);
 }
 
+static void kvm_flush_shadow_all(struct kvm *kvm)
+{
+	kvm_arch_flush_shadow_all(kvm);
+	kvm_arch_guest_memory_reclaimed(kvm);
+}
+
 #ifdef KVM_ARCH_NR_OBJS_PER_MEMORY_CACHE
 static inline void *mmu_memory_cache_alloc_obj(struct kvm_mmu_memory_cache *mc,
 					       gfp_t gfp_flags)
@@ -429,8 +461,8 @@
 
 void kvm_vcpu_destroy(struct kvm_vcpu *vcpu)
 {
-	kvm_dirty_ring_free(&vcpu->dirty_ring);
 	kvm_arch_vcpu_destroy(vcpu);
+	kvm_dirty_ring_free(&vcpu->dirty_ring);
 
 	/*
 	 * No need for rcu_read_lock as VCPU_RUN is the only place that changes
@@ -467,12 +499,15 @@
 typedef void (*on_lock_fn_t)(struct kvm *kvm, unsigned long start,
 			     unsigned long end);
 
+typedef void (*on_unlock_fn_t)(struct kvm *kvm);
+
 struct kvm_hva_range {
 	unsigned long start;
 	unsigned long end;
 	pte_t pte;
 	hva_handler_t handler;
 	on_lock_fn_t on_lock;
+	on_unlock_fn_t on_unlock;
 	bool flush_on_ret;
 	bool may_block;
 };
@@ -549,8 +584,11 @@
 	if (range->flush_on_ret && ret)
 		kvm_flush_remote_tlbs(kvm);
 
-	if (locked)
+	if (locked) {
 		KVM_MMU_UNLOCK(kvm);
+		if (!IS_KVM_NULL_FN(range->on_unlock))
+			range->on_unlock(kvm);
+	}
 
 	srcu_read_unlock(&kvm->srcu, idx);
 
@@ -571,6 +609,7 @@
 		.pte		= pte,
 		.handler	= handler,
 		.on_lock	= (void *)kvm_null_fn,
+		.on_unlock	= (void *)kvm_null_fn,
 		.flush_on_ret	= true,
 		.may_block	= false,
 	};
@@ -590,12 +629,31 @@
 		.pte		= __pte(0),
 		.handler	= handler,
 		.on_lock	= (void *)kvm_null_fn,
+		.on_unlock	= (void *)kvm_null_fn,
 		.flush_on_ret	= false,
 		.may_block	= false,
 	};
 
 	return __kvm_handle_hva_range(kvm, &range);
 }
+
+static bool kvm_change_spte_gfn(struct kvm *kvm, struct kvm_gfn_range *range)
+{
+	/*
+	 * Skipping invalid memslots is correct if and only change_pte() is
+	 * surrounded by invalidate_range_{start,end}(), which is currently
+	 * guaranteed by the primary MMU.  If that ever changes, KVM needs to
+	 * unmap the memslot instead of skipping the memslot to ensure that KVM
+	 * doesn't hold references to the old PFN.
+	 */
+	WARN_ON_ONCE(!READ_ONCE(kvm->mn_active_invalidate_count));
+
+	if (range->slot->flags & KVM_MEMSLOT_INVALID)
+		return false;
+
+	return kvm_set_spte_gfn(kvm, range);
+}
+
 static void kvm_mmu_notifier_change_pte(struct mmu_notifier *mn,
 					struct mm_struct *mm,
 					unsigned long address,
@@ -616,7 +674,7 @@
 	if (!READ_ONCE(kvm->mmu_notifier_count))
 		return;
 
-	kvm_handle_hva_range(mn, address, address + 1, pte, kvm_set_spte_gfn);
+	kvm_handle_hva_range(mn, address, address + 1, pte, kvm_change_spte_gfn);
 }
 
 void kvm_inc_notifier_count(struct kvm *kvm, unsigned long start,
@@ -658,6 +716,7 @@
 		.pte		= __pte(0),
 		.handler	= kvm_unmap_gfn_range,
 		.on_lock	= kvm_inc_notifier_count,
+		.on_unlock	= kvm_arch_guest_memory_reclaimed,
 		.flush_on_ret	= true,
 		.may_block	= mmu_notifier_range_blockable(range),
 	};
@@ -709,6 +768,7 @@
 		.pte		= __pte(0),
 		.handler	= (void *)kvm_null_fn,
 		.on_lock	= kvm_dec_notifier_count,
+		.on_unlock	= (void *)kvm_null_fn,
 		.flush_on_ret	= false,
 		.may_block	= mmu_notifier_range_blockable(range),
 	};
@@ -781,7 +841,7 @@
 	int idx;
 
 	idx = srcu_read_lock(&kvm->srcu);
-	kvm_arch_flush_shadow_all(kvm);
+	kvm_flush_shadow_all(kvm);
 	srcu_read_unlock(&kvm->srcu, idx);
 }
 
@@ -909,7 +969,7 @@
 	int kvm_debugfs_num_entries = kvm_vm_stats_header.num_desc +
 				      kvm_vcpu_stats_header.num_desc;
 
-	if (!kvm->debugfs_dentry)
+	if (IS_ERR(kvm->debugfs_dentry))
 		return;
 
 	debugfs_remove_recursive(kvm->debugfs_dentry);
@@ -1032,6 +1092,9 @@
 	if (!kvm)
 		return ERR_PTR(-ENOMEM);
 
+	/* KVM is pinned via open("/dev/kvm"), the fd passed to this ioctl(). */
+	__module_get(kvm_chardev_ops.owner);
+
 	KVM_MMU_LOCK_INIT(kvm);
 	mmgrab(current->mm);
 	kvm->mm = current->mm;
@@ -1047,6 +1110,12 @@
 
 	BUILD_BUG_ON(KVM_MEM_SLOTS_NUM > SHRT_MAX);
 
+	/*
+	 * Force subsequent debugfs file creations to fail if the VM directory
+	 * is not created (by kvm_create_vm_debugfs()).
+	 */
+	kvm->debugfs_dentry = ERR_PTR(-ENOENT);
+
 	if (init_srcu_struct(&kvm->srcu))
 		goto out_err_no_srcu;
 	if (init_srcu_struct(&kvm->irq_srcu))
@@ -1122,6 +1191,7 @@
 out_err_no_srcu:
 	kvm_arch_free_vm(kvm);
 	mmdrop(current->mm);
+	module_put(kvm_chardev_ops.owner);
 	return ERR_PTR(r);
 }
 
@@ -1176,7 +1246,7 @@
 	WARN_ON(rcuwait_active(&kvm->mn_memslots_update_rcuwait));
 	kvm->mn_active_invalidate_count = 0;
 #else
-	kvm_arch_flush_shadow_all(kvm);
+	kvm_flush_shadow_all(kvm);
 #endif
 	kvm_arch_destroy_vm(kvm);
 	kvm_destroy_devices(kvm);
@@ -1188,6 +1258,7 @@
 	preempt_notifier_dec();
 	hardware_disable_all();
 	mmdrop(mm);
+	module_put(kvm_chardev_ops.owner);
 }
 
 void kvm_get_kvm(struct kvm *kvm)
@@ -1242,9 +1313,9 @@
  */
 static int kvm_alloc_dirty_bitmap(struct kvm_memory_slot *memslot)
 {
-	unsigned long dirty_bytes = 2 * kvm_dirty_bitmap_bytes(memslot);
+	unsigned long dirty_bytes = kvm_dirty_bitmap_bytes(memslot);
 
-	memslot->dirty_bitmap = kvzalloc(dirty_bytes, GFP_KERNEL_ACCOUNT);
+	memslot->dirty_bitmap = __vcalloc(2, dirty_bytes, GFP_KERNEL_ACCOUNT);
 	if (!memslot->dirty_bitmap)
 		return -ENOMEM;
 
@@ -1523,11 +1594,10 @@
 
 static int kvm_set_memslot(struct kvm *kvm,
 			   const struct kvm_userspace_memory_region *mem,
-			   struct kvm_memory_slot *old,
 			   struct kvm_memory_slot *new, int as_id,
 			   enum kvm_mr_change change)
 {
-	struct kvm_memory_slot *slot;
+	struct kvm_memory_slot *slot, old;
 	struct kvm_memslots *slots;
 	int r;
 
@@ -1558,7 +1628,7 @@
 		 * Note, the INVALID flag needs to be in the appropriate entry
 		 * in the freshly allocated memslots, not in @old or @new.
 		 */
-		slot = id_to_memslot(slots, old->id);
+		slot = id_to_memslot(slots, new->id);
 		slot->flags |= KVM_MEMSLOT_INVALID;
 
 		/*
@@ -1576,6 +1646,7 @@
 		 *	- kvm_is_visible_gfn (mmu_check_root)
 		 */
 		kvm_arch_flush_shadow_memslot(kvm, slot);
+		kvm_arch_guest_memory_reclaimed(kvm);
 
 		/* Released in install_new_memslots. */
 		mutex_lock(&kvm->slots_arch_lock);
@@ -1589,6 +1660,26 @@
 		kvm_copy_memslots(slots, __kvm_memslots(kvm, as_id));
 	}
 
+	/*
+	 * Make a full copy of the old memslot, the pointer will become stale
+	 * when the memslots are re-sorted by update_memslots(), and the old
+	 * memslot needs to be referenced after calling update_memslots(), e.g.
+	 * to free its resources and for arch specific behavior.  This needs to
+	 * happen *after* (re)acquiring slots_arch_lock.
+	 */
+	slot = id_to_memslot(slots, new->id);
+	if (slot) {
+		old = *slot;
+	} else {
+		WARN_ON_ONCE(change != KVM_MR_CREATE);
+		memset(&old, 0, sizeof(old));
+		old.id = new->id;
+		old.as_id = as_id;
+	}
+
+	/* Copy the arch-specific data, again after (re)acquiring slots_arch_lock. */
+	memcpy(&new->arch, &old.arch, sizeof(old.arch));
+
 	r = kvm_arch_prepare_memory_region(kvm, new, mem, change);
 	if (r)
 		goto out_slots;
@@ -1596,14 +1687,18 @@
 	update_memslots(slots, new, change);
 	slots = install_new_memslots(kvm, as_id, slots);
 
-	kvm_arch_commit_memory_region(kvm, mem, old, new, change);
+	kvm_arch_commit_memory_region(kvm, mem, &old, new, change);
+
+	/* Free the old memslot's metadata.  Note, this is the full copy!!! */
+	if (change == KVM_MR_DELETE)
+		kvm_free_memslot(kvm, &old);
 
 	kvfree(slots);
 	return 0;
 
 out_slots:
 	if (change == KVM_MR_DELETE || change == KVM_MR_MOVE) {
-		slot = id_to_memslot(slots, old->id);
+		slot = id_to_memslot(slots, new->id);
 		slot->flags &= ~KVM_MEMSLOT_INVALID;
 		slots = install_new_memslots(kvm, as_id, slots);
 	} else {
@@ -1618,7 +1713,6 @@
 			      struct kvm_memory_slot *old, int as_id)
 {
 	struct kvm_memory_slot new;
-	int r;
 
 	if (!old->npages)
 		return -EINVAL;
@@ -1631,12 +1725,7 @@
 	 */
 	new.as_id = as_id;
 
-	r = kvm_set_memslot(kvm, mem, old, &new, as_id, KVM_MR_DELETE);
-	if (r)
-		return r;
-
-	kvm_free_memslot(kvm, old);
-	return 0;
+	return kvm_set_memslot(kvm, mem, &new, as_id, KVM_MR_DELETE);
 }
 
 /*
@@ -1664,7 +1753,8 @@
 	id = (u16)mem->slot;
 
 	/* General sanity checks */
-	if (mem->memory_size & (PAGE_SIZE - 1))
+	if ((mem->memory_size & (PAGE_SIZE - 1)) ||
+	    (mem->memory_size != (unsigned long)mem->memory_size))
 		return -EINVAL;
 	if (mem->guest_phys_addr & (PAGE_SIZE - 1))
 		return -EINVAL;
@@ -1710,7 +1800,6 @@
 	if (!old.npages) {
 		change = KVM_MR_CREATE;
 		new.dirty_bitmap = NULL;
-		memset(&new.arch, 0, sizeof(new.arch));
 	} else { /* Modify an existing slot. */
 		if ((new.userspace_addr != old.userspace_addr) ||
 		    (new.npages != old.npages) ||
@@ -1724,9 +1813,8 @@
 		else /* Nothing to change. */
 			return 0;
 
-		/* Copy dirty_bitmap and arch from the current memslot. */
+		/* Copy dirty_bitmap from the current memslot. */
 		new.dirty_bitmap = old.dirty_bitmap;
-		memcpy(&new.arch, &old.arch, sizeof(new.arch));
 	}
 
 	if ((change == KVM_MR_CREATE) || (change == KVM_MR_MOVE)) {
@@ -1752,7 +1840,7 @@
 			bitmap_set(new.dirty_bitmap, 0, new.npages);
 	}
 
-	r = kvm_set_memslot(kvm, mem, &old, &new, as_id, change);
+	r = kvm_set_memslot(kvm, mem, &new, as_id, change);
 	if (r)
 		goto out_bitmap;
 
@@ -2088,7 +2176,6 @@
 
 	return NULL;
 }
-EXPORT_SYMBOL_GPL(kvm_vcpu_gfn_to_memslot);
 
 bool kvm_is_visible_gfn(struct kvm *kvm, gfn_t gfn)
 {
@@ -2728,16 +2815,28 @@
 }
 EXPORT_SYMBOL_GPL(kvm_release_pfn_dirty);
 
+static bool kvm_is_ad_tracked_pfn(kvm_pfn_t pfn)
+{
+	if (!pfn_valid(pfn))
+		return false;
+
+	/*
+	 * Per page-flags.h, pages tagged PG_reserved "should in general not be
+	 * touched (e.g. set dirty) except by its owner".
+	 */
+	return !PageReserved(pfn_to_page(pfn));
+}
+
 void kvm_set_pfn_dirty(kvm_pfn_t pfn)
 {
-	if (!kvm_is_reserved_pfn(pfn) && !kvm_is_zone_device_pfn(pfn))
+	if (kvm_is_ad_tracked_pfn(pfn))
 		SetPageDirty(pfn_to_page(pfn));
 }
 EXPORT_SYMBOL_GPL(kvm_set_pfn_dirty);
 
 void kvm_set_pfn_accessed(kvm_pfn_t pfn)
 {
-	if (!kvm_is_reserved_pfn(pfn) && !kvm_is_zone_device_pfn(pfn))
+	if (kvm_is_ad_tracked_pfn(pfn))
 		mark_page_accessed(pfn_to_page(pfn));
 }
 EXPORT_SYMBOL_GPL(kvm_set_pfn_accessed);
@@ -2985,7 +3084,8 @@
 	int r;
 	gpa_t gpa = ghc->gpa + offset;
 
-	BUG_ON(len + offset > ghc->len);
+	if (WARN_ON_ONCE(len + offset > ghc->len))
+		return -EINVAL;
 
 	if (slots->generation != ghc->generation) {
 		if (__kvm_gfn_to_hva_cache_init(slots, ghc, ghc->gpa, ghc->len))
@@ -3022,7 +3122,8 @@
 	int r;
 	gpa_t gpa = ghc->gpa + offset;
 
-	BUG_ON(len + offset > ghc->len);
+	if (WARN_ON_ONCE(len + offset > ghc->len))
+		return -EINVAL;
 
 	if (slots->generation != ghc->generation) {
 		if (__kvm_gfn_to_hva_cache_init(slots, ghc, ghc->gpa, ghc->len))
@@ -3205,6 +3306,7 @@
  */
 void kvm_vcpu_block(struct kvm_vcpu *vcpu)
 {
+	bool halt_poll_allowed = !kvm_arch_no_poll(vcpu);
 	ktime_t start, cur, poll_end;
 	bool waited = false;
 	u64 block_ns;
@@ -3212,7 +3314,7 @@
 	kvm_arch_vcpu_blocking(vcpu);
 
 	start = cur = poll_end = ktime_get();
-	if (vcpu->halt_poll_ns && !kvm_arch_no_poll(vcpu)) {
+	if (vcpu->halt_poll_ns && halt_poll_allowed) {
 		ktime_t stop = ktime_add_ns(ktime_get(), vcpu->halt_poll_ns);
 
 		++vcpu->stat.generic.halt_attempted_poll;
@@ -3267,7 +3369,7 @@
 	update_halt_poll_stats(
 		vcpu, ktime_to_ns(ktime_sub(poll_end, start)), waited);
 
-	if (!kvm_arch_no_poll(vcpu)) {
+	if (halt_poll_allowed) {
 		if (!vcpu_valid_wakeup(vcpu)) {
 			shrink_halt_poll_ns(vcpu);
 		} else if (vcpu->kvm->max_halt_poll_ns) {
@@ -3426,12 +3528,13 @@
 {
 	struct kvm *kvm = me->kvm;
 	struct kvm_vcpu *vcpu;
-	int last_boosted_vcpu = me->kvm->last_boosted_vcpu;
+	int last_boosted_vcpu;
 	int yielded = 0;
 	int try = 3;
 	int pass;
 	int i;
 
+	last_boosted_vcpu = READ_ONCE(kvm->last_boosted_vcpu);
 	kvm_vcpu_set_in_spin_loop(me, true);
 	/*
 	 * We boost the priority of a VCPU that is runnable but not
@@ -3463,7 +3566,7 @@
 
 			yielded = kvm_vcpu_yield_to(vcpu);
 			if (yielded > 0) {
-				kvm->last_boosted_vcpu = i;
+				WRITE_ONCE(kvm->last_boosted_vcpu, i);
 				break;
 			} else if (yielded < 0) {
 				try--;
@@ -3702,8 +3805,17 @@
 			sizeof(vcpu->stat), user_buffer, size, offset);
 }
 
+static int kvm_vcpu_stats_release(struct inode *inode, struct file *file)
+{
+	struct kvm_vcpu *vcpu = file->private_data;
+
+	kvm_put_kvm(vcpu->kvm);
+	return 0;
+}
+
 static const struct file_operations kvm_vcpu_stats_fops = {
 	.read = kvm_vcpu_stats_read,
+	.release = kvm_vcpu_stats_release,
 	.llseek = noop_llseek,
 };
 
@@ -3724,6 +3836,9 @@
 		put_unused_fd(fd);
 		return PTR_ERR(file);
 	}
+
+	kvm_get_kvm(vcpu->kvm);
+
 	file->f_mode |= FMODE_PREAD;
 	fd_install(fd, file);
 
@@ -4135,8 +4250,11 @@
 		kvm_put_kvm_no_destroy(kvm);
 		mutex_lock(&kvm->lock);
 		list_del(&dev->vm_node);
+		if (ops->release)
+			ops->release(dev);
 		mutex_unlock(&kvm->lock);
-		ops->destroy(dev);
+		if (ops->destroy)
+			ops->destroy(dev);
 		return ret;
 	}
 
@@ -4304,8 +4422,17 @@
 				sizeof(kvm->stat), user_buffer, size, offset);
 }
 
+static int kvm_vm_stats_release(struct inode *inode, struct file *file)
+{
+	struct kvm *kvm = file->private_data;
+
+	kvm_put_kvm(kvm);
+	return 0;
+}
+
 static const struct file_operations kvm_vm_stats_fops = {
 	.read = kvm_vm_stats_read,
+	.release = kvm_vm_stats_release,
 	.llseek = noop_llseek,
 };
 
@@ -4324,6 +4451,9 @@
 		put_unused_fd(fd);
 		return PTR_ERR(file);
 	}
+
+	kvm_get_kvm(kvm);
+
 	file->f_mode |= FMODE_PREAD;
 	fd_install(fd, file);
 
@@ -4542,6 +4672,12 @@
 	};
 };
 
+long __weak kvm_arch_vm_compat_ioctl(struct file *filp, unsigned int ioctl,
+				     unsigned long arg)
+{
+	return -ENOTTY;
+}
+
 static long kvm_vm_compat_ioctl(struct file *filp,
 			   unsigned int ioctl, unsigned long arg)
 {
@@ -4550,6 +4686,11 @@
 
 	if (kvm->mm != current->mm || kvm->vm_bugged)
 		return -EIO;
+
+	r = kvm_arch_vm_compat_ioctl(filp, ioctl, arg);
+	if (r != -ENOTTY)
+		return r;
+
 	switch (ioctl) {
 #ifdef CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT
 	case KVM_CLEAR_DIRTY_LOG: {
@@ -5342,7 +5483,7 @@
 	}
 	add_uevent_var(env, "PID=%d", kvm->userspace_pid);
 
-	if (kvm->debugfs_dentry) {
+	if (!IS_ERR(kvm->debugfs_dentry)) {
 		char *tmp, *p = kmalloc(PATH_MAX, GFP_KERNEL_ACCOUNT);
 
 		if (p) {
@@ -5399,9 +5540,7 @@
 static void kvm_resume(void)
 {
 	if (kvm_usage_count) {
-#ifdef CONFIG_LOCKDEP
-		WARN_ON(lockdep_is_held(&kvm_count_lock));
-#endif
+		lockdep_assert_not_held(&kvm_count_lock);
 		hardware_enable_nolock(NULL);
 	}
 }
@@ -5543,20 +5682,22 @@
 		goto out_free_3;
 	}
 
+	for_each_possible_cpu(cpu) {
+		if (!alloc_cpumask_var_node(&per_cpu(cpu_kick_mask, cpu),
+					    GFP_KERNEL, cpu_to_node(cpu))) {
+			r = -ENOMEM;
+			goto out_free_4;
+		}
+	}
+
 	r = kvm_async_pf_init();
 	if (r)
-		goto out_free;
+		goto out_free_4;
 
 	kvm_chardev_ops.owner = module;
 	kvm_vm_fops.owner = module;
 	kvm_vcpu_fops.owner = module;
 
-	r = misc_register(&kvm_dev);
-	if (r) {
-		pr_err("kvm: misc device register failed\n");
-		goto out_unreg;
-	}
-
 	register_syscore_ops(&kvm_syscore_ops);
 
 	kvm_preempt_ops.sched_in = kvm_sched_in;
@@ -5565,13 +5706,28 @@
 	kvm_init_debug();
 
 	r = kvm_vfio_ops_init();
-	WARN_ON(r);
+	if (WARN_ON_ONCE(r))
+		goto err_vfio;
+
+	/*
+	 * Registration _must_ be the very last thing done, as this exposes
+	 * /dev/kvm to userspace, i.e. all infrastructure must be setup!
+	 */
+	r = misc_register(&kvm_dev);
+	if (r) {
+		pr_err("kvm: misc device register failed\n");
+		goto err_register;
+	}
 
 	return 0;
 
-out_unreg:
+err_register:
+	kvm_vfio_ops_exit();
+err_vfio:
 	kvm_async_pf_deinit();
-out_free:
+out_free_4:
+	for_each_possible_cpu(cpu)
+		free_cpumask_var(per_cpu(cpu_kick_mask, cpu));
 	kmem_cache_destroy(kvm_vcpu_cache);
 out_free_3:
 	unregister_reboot_notifier(&kvm_reboot_notifier);
@@ -5591,8 +5747,18 @@
 
 void kvm_exit(void)
 {
-	debugfs_remove_recursive(kvm_debugfs_dir);
+	int cpu;
+
+	/*
+	 * Note, unregistering /dev/kvm doesn't strictly need to come first,
+	 * fops_get(), a.k.a. try_module_get(), prevents acquiring references
+	 * to KVM while the module is being stopped.
+	 */
 	misc_deregister(&kvm_dev);
+
+	debugfs_remove_recursive(kvm_debugfs_dir);
+	for_each_possible_cpu(cpu)
+		free_cpumask_var(per_cpu(cpu_kick_mask, cpu));
 	kmem_cache_destroy(kvm_vcpu_cache);
 	kvm_async_pf_deinit();
 	unregister_syscore_ops(&kvm_syscore_ops);